Small Signal Loudspeaker Impedance Emulator

DEFF Research Database (Denmark)

Iversen, Niels Elkjær; Knott, Arnold

2014-01-01

Specifying the performance of audio amplifiers is typically done by playing sine waves into a pure ohmic load. However real loudspeaker impedances are not purely ohmic but characterized by the mechanical resonance between the mass of the diaphragm and the compliance of its suspension which vary...... from driver to driver. Therefore, a loudspeaker emulator capable of adjusting its impedance to that of a given driver is desired for measurement purposes. This paper proposes a loudspeaker emulator circuit for small signals. Simulations and experimental results are compared and show that it is possible...... to emulate the loudspeaker impedance with an electric circuit and that its resonance frequency can be changed by tuning two resistors....

Small-signal Loudspeaker Impedance Emulator

DEFF Research Database (Denmark)

Knott, Arnold; Iversen, Niels Elkjær

2014-01-01

Specifying the performance of audio ampliers is typically done by playing sine waves into a pure ohmic load. However real loudspeaker impedances are not purely ohmic but characterised by the mechanical resonance between the mass of the diaphragm and the compliance of its' suspension which vary from...... driver to driver. Therefore a loudspeaker emulator capable of adjusting its' impedance to a given driver is in need for measurement purposes. This paper proposes a loudspeaker emulator circuit for small signals. Simulations and experimental results are compared and show that it is possible to emulate...... the loudspeaker impedance with an electric circuit and that its' resonance frequency can be changed by tuning two resistors....

Emulation of dynamic simulators with application to hydrology

Energy Technology Data Exchange (ETDEWEB)

Machac, David, E-mail: david.machac@eawag.ch [Eawag, Swiss Federal Institute of Aquatic Science and Technology, Department of Systems Analysis, Integrated Assessment and Modelling, 8600 Dübendorf (Switzerland); ETH Zurich, Department of Environmental Systems Science, 8092 Zurich (Switzerland); Reichert, Peter [Eawag, Swiss Federal Institute of Aquatic Science and Technology, Department of Systems Analysis, Integrated Assessment and Modelling, 8600 Dübendorf (Switzerland); ETH Zurich, Department of Environmental Systems Science, 8092 Zurich (Switzerland); Albert, Carlo [Eawag, Swiss Federal Institute of Aquatic Science and Technology, Department of Systems Analysis, Integrated Assessment and Modelling, 8600 Dübendorf (Switzerland)

2016-05-15

Many simulation-intensive tasks in the applied sciences, such as sensitivity analysis, parameter inference or real time control, are hampered by slow simulators. Emulators provide the opportunity of speeding up simulations at the cost of introducing some inaccuracy. An emulator is a fast approximation to a simulator that interpolates between design input–output pairs of the simulator. Increasing the number of design data sets is a computationally demanding way of improving the accuracy of emulation. We investigate the complementary approach of increasing emulation accuracy by including knowledge about the mechanisms of the simulator into the formulation of the emulator. To approximately reproduce the output of dynamic simulators, we consider emulators that are based on a system of linear, ordinary or partial stochastic differential equations with a noise term formulated as a Gaussian process of the parameters to be emulated. This stochastic model is then conditioned to the design data so that it mimics the behavior of the nonlinear simulator as a function of the parameters. The drift terms of the linear model are designed to provide a simplified description of the simulator as a function of its key parameters so that the required corrections by the conditioned Gaussian process noise are as small as possible. The goal of this paper is to compare the gain in accuracy of these emulators by enlarging the design data set and by varying the degree of simplification of the linear model. We apply this framework to a simulator for the shallow water equations in a channel and compare emulation accuracy for emulators based on different spatial discretization levels of the channel and for a standard non-mechanistic emulator. Our results indicate that we have a large gain in accuracy already when using the simplest mechanistic description by a single linear reservoir to formulate the drift term of the linear model. Adding some more reservoirs does not lead to a significant

The role of endogenous lipids in the emulsifying properties of cocoa

Science.gov (United States)

Gould, Joanne; Furse, Samuel; Wolf, Bettina

2016-03-01

This paper describes a study in which the emulsifying properties of cocoa material with and without its lipid fraction were explored. This study was motivated by the commercial interest in naturally-occurring particulate emulsifiers as opposed to the chemically modified emulsifying particles presently available for commercial use. The hypothesis was that endogenous lipids from cocoa were responsible for driving the formation of stable oil-in-water (o/w) emulsions. The data presented includes relative quantification of phospholipids from different commercially available cocoa material using 31P NMR spectroscopy and analyses of the emulsifying power of delipidified cocoa material. The commercially available cocoa material comprised several phospholipids, with phosphatidylcholine being the most abundant in all samples. Dispersions of delipidified cocoa material were found to drive the formation of o/w emulsions despite the absence of lipids. We therefore concluded that the emulsifying behaviour of cocoa material is not entirely reliant upon the endogenous lipids. This suggests that cocoa material may have a new and potentially widespread use in industrial food preparation and may inform manufacturing strategies for novel food grade emulsifiers.

Termite: Emulation Testbed for Encounter Networks

Directory of Open Access Journals (Sweden)

Rodrigo Bruno

2015-08-01

Full Text Available Cutting-edge mobile devices like smartphones and tablets are equipped with various infrastructureless wireless interfaces, such as WiFi Direct and Bluetooth. Such technologies allow for novel mobile applications that take advantage of casual encounters between co-located users. However, the need to mimic the behavior of real-world encounter networks makes testing and debugging of such applications hard tasks. We present Termite, an emulation testbed for encounter networks. Our system allows developers to run their applications on a virtual encounter network emulated by software. Developers can model arbitrary encounter networks and specify user interactions on the emulated virtual devices. To facilitate testing and debugging, developers can place breakpoints, inspect the runtime state of virtual nodes, and run experiments in a stepwise fashion. Termite defines its own Petri Net variant to model the dynamically changing topology and synthesize user interactions with virtual devices. The system is designed to efficiently multiplex an underlying emulation hosting infrastructure across multiple developers, and to support heterogeneous mobile platforms. Our current system implementation supports virtual Android devices communicating over WiFi Direct networks and runs on top of a local cloud infrastructure. We evaluated our system using emulator network traces, and found that Termite is expressive and performs well.

Desenvolvimento e estudos de estabilidade preliminares de emulsões O/A contendo Cetoconazol 2,0% = Development and Preliminary Stability Evaluations of O/W emulsion containing Ketoconazole 2.0%

Directory of Open Access Journals (Sweden)

Vanessa Catalá Casteli

2008-07-01

Full Text Available O objetivo deste trabalho foi desenvolver emulsões O/A contendo Cetoconazol 2,0% e avaliar sua estabilidade preliminar por meio da análise de suas características físicoquímicas, tais como homogeneidade, formação de agregados, floculação, cremeação ecoalescência. As emulsões foram formuladas utilizando diferentes bases autoemulsionantes, compostas por álcool cetoestearílico, álcool etoxilado, álcool graxos superiores, ácido esteárico, lanolina e outros. As emulsões foram submetidas aos testes de centrifugação,estresse térmico e ciclo gela-degela, e suas características organolépticas e físico-químicas foram avaliadas no início e no final de cada ensaio. Todas as amostras mantiveram sua homogeneidade após o teste de centrifugação, mas somente os sistemas preparados comceras autoemulsionáveis constituídas por álcool graxos superiores (Polawax NF® e Copolímero de Amônio Acriloil dimetiltaurato VP, Trilauril 4 fosfato, Sesquisosterato de metil glicose, Óleo de flores de verão e Tetradibutil pentaeritritil hidroxihidrocinamato deGlicerina (Hostacerin NCB® mantiveram sua estabilidade após testes de estresse térmico e ciclo gela-degela.The objective of this work was the development of O/W emulsions containing Ketoconazole 2.0% and to evaluate their preliminary stability by analyzing physical-chemical characteristics such as homogeneity, aggregation formation, flocculation, creaming and coalescence. The emulsions were formulated using different self-emulsifying bases, composed of cetearyl alcohol, ethoxylalcohol, higher fatty alcohol, stearic acid, lanolin and others. The O/W emulsions were evaluated by centrifugation test, thermal stress test, and freezing/defrosting cycles, and its organoleptic and physical-chemistry characteristics were analyzed before and after eachassay. All samples maintained their homogeneity after the centrifugation test, but only the systems prepared with self emulsifying composed of

Optimization of Emulsifying Effectiveness of Phytosterol in Milk Using Two-Level Fractional Factorial Design

Directory of Open Access Journals (Sweden)

He Yunxia

2017-12-01

Full Text Available In this paper emulsifying effects of seven emulsifiers including Tween 80, Span 80, tripolyglycerol monostearate, sodium stearoyl lactylate, sucrose ester, soy lecithin and monoglyceride on phytosterol in milk were investigated using single factor test and fractional factorial design. The addition for seven emulsifiers were in the following concentrations: 0.1%, 0.2%, 0.3%, 0.4%, 0.5% and 0.6%. The results revealed that tripolyglycerol monostearate, sucrose ester and monoglyceride had a significant emulsifying effect on phytosterol in milk, Tripolyglycerol monostearate showed a positive emulsifying effect on phytosterol in milk, while sucrose ester and monoglyceride exhibited a negative emulsifying effect on phytosterol in milk.

Dietary emulsifiers impact the mouse gut microbiota promoting colitis and metabolic syndrome.

Science.gov (United States)

Chassaing, Benoit; Koren, Omry; Goodrich, Julia K; Poole, Angela C; Srinivasan, Shanthi; Ley, Ruth E; Gewirtz, Andrew T

2015-03-05

The intestinal tract is inhabited by a large and diverse community of microbes collectively referred to as the gut microbiota. While the gut microbiota provides important benefits to its host, especially in metabolism and immune development, disturbance of the microbiota-host relationship is associated with numerous chronic inflammatory diseases, including inflammatory bowel disease and the group of obesity-associated diseases collectively referred to as metabolic syndrome. A primary means by which the intestine is protected from its microbiota is via multi-layered mucus structures that cover the intestinal surface, thereby allowing the vast majority of gut bacteria to be kept at a safe distance from epithelial cells that line the intestine. Thus, agents that disrupt mucus-bacterial interactions might have the potential to promote diseases associated with gut inflammation. Consequently, it has been hypothesized that emulsifiers, detergent-like molecules that are a ubiquitous component of processed foods and that can increase bacterial translocation across epithelia in vitro, might be promoting the increase in inflammatory bowel disease observed since the mid-twentieth century. Here we report that, in mice, relatively low concentrations of two commonly used emulsifiers, namely carboxymethylcellulose and polysorbate-80, induced low-grade inflammation and obesity/metabolic syndrome in wild-type hosts and promoted robust colitis in mice predisposed to this disorder. Emulsifier-induced metabolic syndrome was associated with microbiota encroachment, altered species composition and increased pro-inflammatory potential. Use of germ-free mice and faecal transplants indicated that such changes in microbiota were necessary and sufficient for both low-grade inflammation and metabolic syndrome. These results support the emerging concept that perturbed host-microbiota interactions resulting in low-grade inflammation can promote adiposity and its associated metabolic effects

Loudspeaker impedance emulator for multi resonant systems

DEFF Research Database (Denmark)

Iversen, Niels Elkjær; Knott, Arnold

2015-01-01

Specifying the performance of audio amplifiers is typically done by playing sine waves into a pure ohmic load. However real loudspeaker impedances are not purely ohmic but characterised by its electrical, mechanical and acoustical properties. Therefore a loudspeaker emulator capable of adjusting...... its impedance to that of a given loudspeaker is desired for measurement purposes. An adjustable RLC based emulator is implemented with switch controlled capacitors, air gap controlled inductors and potentiometers. Calculations and experimental results are compared and show that it is possible...... to emulate the loudspeaker impedance infinite baffle-, closed box- and the multi resonant vented box-loudspeaker by tuning the component values in the proposed circuit. Future work is outlined and encourage that the proposed impedance emulator is used as part of a control circuit in a switch-mode based...

Evaluating Emulation-based Models of Distributed Computing Systems

Energy Technology Data Exchange (ETDEWEB)

Jones, Stephen T. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Cyber Initiatives; Gabert, Kasimir G. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Cyber Initiatives; Tarman, Thomas D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Emulytics Initiatives

2017-08-01

Emulation-based models of distributed computing systems are collections of virtual ma- chines, virtual networks, and other emulation components configured to stand in for oper- ational systems when performing experimental science, training, analysis of design alterna- tives, test and evaluation, or idea generation. As with any tool, we should carefully evaluate whether our uses of emulation-based models are appropriate and justified. Otherwise, we run the risk of using a model incorrectly and creating meaningless results. The variety of uses of emulation-based models each have their own goals and deserve thoughtful evaluation. In this paper, we enumerate some of these uses and describe approaches that one can take to build an evidence-based case that a use of an emulation-based model is credible. Predictive uses of emulation-based models, where we expect a model to tell us something true about the real world, set the bar especially high and the principal evaluation method, called validation , is comensurately rigorous. We spend the majority of our time describing and demonstrating the validation of a simple predictive model using a well-established methodology inherited from decades of development in the compuational science and engineering community.

Implementation of Fast Emulator-based Code Calibration

Energy Technology Data Exchange (ETDEWEB)

Bowman, Nathaniel [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Risk & Reliability Analysis; Denman, Matthew R [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Risk & Reliability Analysis

2016-08-01

Calibration is the process of using experimental data to gain more precise knowledge of simulator inputs. This process commonly involves the use of Markov-chain Monte Carlo, which requires running a simulator thousands of times. If we can create a faster program, called an emulator, that mimics the outputs of the simulator for an input range of interest, then we can speed up the process enough to make it feasible for expensive simulators. To this end, we implement a Gaussian-process emulator capable of reproducing the behavior of various long-running simulators to within acceptable tolerance. This fast emulator can be used in place of a simulator to run Markov-chain Monte Carlo in order to calibrate simulation parameters to experimental data. As a demonstration, this emulator is used to calibrate the inputs of an actual simulator against two sodium-fire experiments.

Statistical Emulator for Expensive Classification Simulators

Science.gov (United States)

Ross, Jerret; Samareh, Jamshid A.

2016-01-01

Expensive simulators prevent any kind of meaningful analysis to be performed on the phenomena they model. To get around this problem the concept of using a statistical emulator as a surrogate representation of the simulator was introduced in the 1980's. Presently, simulators have become more and more complex and as a result running a single example on these simulators is very expensive and can take days to weeks or even months. Many new techniques have been introduced, termed criteria, which sequentially select the next best (most informative to the emulator) point that should be run on the simulator. These criteria methods allow for the creation of an emulator with only a small number of simulator runs. We follow and extend this framework to expensive classification simulators.

Preparation and evaluation of nattokinase-loaded self-double-emulsifying drug delivery system

OpenAIRE

Wang, Xiaona; Jiang, Sifan; Wang, Xinyue; Liao, Jie; Yin, Zongning

2015-01-01

In the present study, we prepared nattokinase-loaded self-double-emulsifying drug delivery system (SDEDDS) and investigated its preliminary pharmacodynamics. The type and concentration of oil phase, inner aqueous phase and emulsifier were screened to prepare optimum nattokinase-loaded SDEDDS. Next, the optimum formulations were characterized based on microstructure, volume-weighted mean droplet size, self-emulsifying rate, yield, storage stability, in vitro release and in vivo pharmacodynamic...

The Ratios of Pre-emulsified Duck Skin for Optimized Processing of Restructured Ham.

Science.gov (United States)

Shim, Jae-Yun; Kim, Tae-Kyung; Kim, Young-Boong; Jeon, Ki-Hong; Ahn, Kwang-Il; Paik, Hyun-Dong; Choi, Yun-Sang

2018-02-01

The purpose of this study was to investigate the quality of duck ham formulated with duck skin through the pre-emulsification process. The experiments to investigate the quality characteristics of duck ham were carried out to measure proximate composition, cooking loss, emulsion stability, pH, color, texture profile analysis, apparent viscosity, and sensory characteristics. Duck ham was prepared with various ratios of duck skin in pre-emulsion as follows: Control (duct skin 30%), T1 (duck skin 20% + pre-emulsified duck skin 10%), T2 (duck skin 15% + pre-emulsified duck skin 15%), T3 (duck skin 10% + pre-emulsified duck skin 20%), and T4 (pre-emulsified duck skin 30%). As the ratio of duck skin to pre-emulsified skin changed, the quality of duck ham in terms of moisture content, fat content, cooking loss, emulsion stability, lightness, textural analysis, apparent viscosity, and overall acceptability changed. The moisture content of T2 was the highest ( p ham and 1:1 ratio of duck skin and pre-emulsified skin was the proper ratio to improve the quality characteristics of duck ham.

Preparation and evaluation of Vinpocetine self-emulsifying pH gradient release pellets.

Science.gov (United States)

Liu, Mengqi; Zhang, Shiming; Cui, Shuxia; Chen, Fen; Jia, Lianqun; Wang, Shu; Gai, Xiumei; Li, Pingfei; Yang, Feifei; Pan, Weisan; Yang, Xinggang

2017-11-01

The main objective of this study was to develop a pH gradient release pellet with self-emulsifying drug delivery system (SEDDS), which could not only improve the oral bioavailability of Vinpocetine (VIN), a poor soluble drug, but reduce the fluctuation of plasma concentration. First, the liquid VIN SEDDS formulation was prepared. Then the self-emulsifying pH gradient release pellets were prepared by extrusion spheronization technique, and formulation consisted by the liquid SEDDS, absorbent (colloidal silicon dioxide), penetration enhancer (sodium chloride), microcrystalline cellulose, ethyl alcohol, and three coating materials (HPMC, Eudragit L30D55, Eudragit FS30D) were eventually selected. Three kinds of coated pellets were mixed in capsules with the mass ratio of 1:1:1. The release curves of capsules were investigated in vitro under the simulated gastrointestinal conditions. In addition, the oral bioavailability and pharmacokinetics of VIN self-emulsifying pH gradient release pellets, commercial tablets and liquid VIN SEDDS were evaluated in Beagle dogs. The oral bioavailability of self-emulsifying pH gradient release pellets was about 149.8% of commercial VIN tablets, and it was about 86% of liquid VIN SEDDS, but there were no significant difference between liquid SEDDS and self-emulsifying pH gradient release pellets. In conclusion, the self-emulsifying pH gradient release pellets could significantly enhance the absorption of VIN and effectively achieve a pH gradient release. And the self-emulsifying pH gradient release pellet was a promising method to improve bioavailability of insoluble drugs.

21 CFR 524.1742 - N-(Mercaptomethyl) phthalimide S-(O,O-dimethyl phosphorodithioate) emulsifiable liquid.

Science.gov (United States)

2010-04-01

... phosphorodithioate) emulsifiable liquid. 524.1742 Section 524.1742 Food and Drugs FOOD AND DRUG ADMINISTRATION... phosphorodithioate) emulsifiable liquid. (a) Specifications. The emulsifiable liquid contains 11.6 percent N... soap and water; for eyes, flush with water. Wash all contaminated clothing with soap and hot water...

Using oily wastewater emulsified fuel in boiler: energy saving and reduction of air pollutant emissions.

Science.gov (United States)

Chen, Chun-Chi; Lee, Wen-Jhy

2008-01-01

The limited data for using emulsified oil have demonstrated its effectiveness in reducing flue gas pollutant emissions. The presence of a high concentration of toxic organic compounds in industrial wastewaters always presents significant problems. Therefore, this study was undertaken by using wastewater with COD of 9600 mg/L and total petroleum hydrocarbons-gasoline 440 mg/L for making an emulsified oil (wastewater content 20% with 0.1% surfactant) to evaluate the extent of reductions in both criteria pollutants and polycyclic aromatic hydrocarbons. For comparison, two other systems (heavy oil fuel and water-emulsified oil) were also conducted. The wastewater-emulsified oil fuel results in significant reductions in particulate matter (PM), NO(x), SO2, and CO as compared to heavy oil fuel and similar to those from water/oil emulsified fuel; for PM, it is better in wastewater-emulsified oil. The reductions of total PAH flue gas emissions are 38 and 30% for wastewater- and water-emulsified fuel, respectively; they are 63 and 44% for total BaP(eq), respectively. In addition to reducing flue gas pollutant emissions, the results also demonstrate that the use of wastewater-emulsified fuel in boiler operation provides several advantages: (1) safe disposal of industrial wastewater; and (2) energy savings of about 13%. Thus, wastewater/oil-emulsified fuel is highly suitable for use in boilers.

Fire Emulator/Detector Evaluator

Data.gov (United States)

Federal Laboratory Consortium — Description:The fire emulator/detector evaluator (FE/DE) is a computer-controlled flow tunnel used to re-create the environments surrounding detectors in the early...

SSCI 125 emulation of Point Lepreau G.S

International Nuclear Information System (INIS)

MacLean, M.; Hogg, J.; Newman, H.; Thompson, H.

1997-01-01

A C language program has been developed at the Point Lepreau Nuclear Generating Station which emulates the actions of an SSCI 125 computer's instruction set and also emulates the actions of those input and output devices which belong to the plant control computer of the nuclear power plant's full scope training simulator. This enables the same DCC software to run on both the $20 million dollar training simulator and an equivalent desktop simulator whose hardware cost is now $16,000 or less. It facilitates making additional copies of the $20 million dollar training simulator for less than 0.1% of the cost per copy. When this emulation program is run on a 266 MHz DEC single CPU Alpha computer, it simulates the running of the training simulator plant control DCC (digital control computer) at approximately the rate of real time: either faster or slightly slower depending on the compiler options employed and depending on the choice of the modeled machine cycle speed of the SSCI. Using the standard machine cycle speed of 660 nanoseconds, using the emulator fully optimized and using plant process modelling without optimization the speed is 90% as fast as real time - this is the normal use situation for simulator modelers who were the originally intended users of the emulator. If the modeled SSCI machine cycle speed is slowed down to 792 nanoseconds (making use of space capacity on the real SSCI to reduce the workload of emulation), and all objects are compiled as optimized, then it takes only about 20 minutes of clock time to simulate over 30 minutes of modelling time. This mode of simulation may be useful for somebody who is not doing emulator or modeling code development. This could include preparing lesson plans for the training simulator, developing or evaluating plant operating procedures or trying out revised DCC software. (DM)

The effect of different emulsifiers on the eggless cake properties containing WPC.

Science.gov (United States)

Khalilian Movahhed, Mohammad; Mohebbi, Mohebbat; Koocheki, Arash; Milani, Elnaz

2016-11-01

The possibility of complete replacement of egg proteins with whey protein concentrate (WPC) and improvement in quality by different emulsifiers was evaluated. Three emulsifiers, including polyglycerol ester (PGE), distilled mono glyceride (DMG) and lecithin were used to bake eggless cakes, containing 8% (w/w) WPC. The response surface analysis was applied to study the effect of emulsifiers on the eggless cake properties. The emulsifiers, individually and interactively, improved the properties of the eggless cakes significantly. The PGE and DMG decreased the batter density, however lecithin increased it. All emulsifiers increased the porosity and volume of the eggless cakes, but decreased the hardness and gumminess of crumb and improved the sensory acceptance. The indices used for optimization of formulation were water activity, moisture content, hardness, gumminess, volume, porosity and total acceptance. The optimum quality of the eggless cake can be achieved from a combination of 0.5 PGE, 0.25 DMG and 0.5% lecithin. The experimental and predicted responses of the optimized eggless cake had a good resemblance.

SONEP: A Software-Defined Optical Network Emulation Platform

DEFF Research Database (Denmark)

Azodolmolky, Siamak; Petersen, Martin Nordal; Fagertun, Anna Manolova

2014-01-01

Network emulation has been one of the tools of choice for conducting experiments on commodity hardware. In the absence of an easy to use optical network test-bed, researchers can significantly benefit from the availability of a flexible/programmable optical network emulation platform. Exploiting...... the lightweight system virtualization, which is recently supported in modern operating systems, in this work we present the architecture of a Software-Defined Network (SDN) emulation platform for transport optical networks and investigate its usage in a use-case scenario. To the best of our knowledge......, this is for the first time that an SDN-based emulation platform is proposed for modeling and performance evaluation of optical networks. Coupled with recent trend of extension of SDN towards transport (optical) networks, the presented tool can facilitate the evaluation of innovative idea before actual implementations...

Preparation and evaluation of nattokinase-loaded self-double-emulsifying drug delivery system

Directory of Open Access Journals (Sweden)

Xiaona Wang

2015-10-01

Full Text Available In the present study, we prepared nattokinase-loaded self-double-emulsifying drug delivery system (SDEDDS and investigated its preliminary pharmacodynamics. The type and concentration of oil phase, inner aqueous phase and emulsifier were screened to prepare optimum nattokinase-loaded SDEDDS. Next, the optimum formulations were characterized based on microstructure, volume-weighted mean droplet size, self-emulsifying rate, yield, storage stability, in vitro release and in vivo pharmacodynamics studies. The water/oil/water multiple emulsions exhibited typical multiple structure, with relatively small volume-weighted mean droplet size 6.0 ± 0.7 μm and high self-emulsifying ability (self-emulsifying time <2 min. Encapsulation of nattokinase was up to 86.8 ± 8.2%. The cumulative release of nattokinase within 8 h was about 30%, exhibiting a sustained release effect. The pharmacodynamics study indicated that nattokinase-loaded SDEDDS could significantly prolong the whole blood clotting time in mouse and effectively improve the carrageenan-induced tail thrombosis compared with nattokinase solution. Moreover, we showed that SDEDDS could successfully self-emulsify into water/oil/water multiple emulsions upon dilution in dispersion medium with gentle stirring and effectively protect nattokinase activity in gastric environment. Our findings suggested that SDEDDS could be a promising strategy for peptide and protein drugs by oral administration.

Foaming and emulsifying properties of pectin isolated from different plant materials

Science.gov (United States)

Yancheva, Nikoleta; Markova, Daniela; Murdzheva, Dilyana; Vasileva, Ivelina; Slavov, Anton

2016-03-01

The foaming and emulsifying properties of pectins obtained from waste rose petals, citrus pressings, grapefruit peels and celery were studied. It was found that the highest foaming capacity showed pectin derived from celery. The effect of pectin concentration on the foaming capacity of pectin solutions was investigated. For all the investigated pectins increasing the concentration led to increase of the foaming capacity. Emulsifying activity and emulsion stability of model emulsion systems (50 % oil phase) with 0.6 % pectic solutions were determined. The highest emulsifying activity and stability showed pectin isolated by dilute acid extraction from waste rose petals.

Foaming and emulsifying properties of pectin isolated from different plant materials

Directory of Open Access Journals (Sweden)

Yancheva Nikoleta

2016-03-01

Full Text Available The foaming and emulsifying properties of pectins obtained from waste rose petals, citrus pressings, grapefruit peels and celery were studied. It was found that the highest foaming capacity showed pectin derived from celery. The effect of pectin concentration on the foaming capacity of pectin solutions was investigated. For all the investigated pectins increasing the concentration led to increase of the foaming capacity. Emulsifying activity and emulsion stability of model emulsion systems (50 % oil phase with 0.6 % pectic solutions were determined. The highest emulsifying activity and stability showed pectin isolated by dilute acid extraction from waste rose petals.

Investigations on burning efficiency and exhaust emission of in-line type emulsified fuel system

Energy Technology Data Exchange (ETDEWEB)

Tseng, Y.K. [National Chinyi University of Technology (Taiwan). Dept. of Mechanical Engineering; Cheng, H.C. [Point Environmental Protection Technology Company Limited (Taiwan)

2011-07-28

In this research, the burning efficiency as well as exhaust emission of a new water-in-oil emulsified fuel system was studied. This emulsified system contains two core processes, the first one is to mix 97% water with 3% emulsifier by volume, and get the milk-like emulsified liquid, while the second one is to compound the milk-like emulsified liquid with heavy oil then obtain the emulsified fuel. In order to overcome the used demulsification problem during in reserve or in transport, this system was designed as a made and use in-line type. From the results of a series of burning tests, the fuel saving can be 8--15%. Also, from the comparison of decline for the heat value and total energy output of emulsified fuel, one can find that the water as the dispersed phase in the combustion process will lead to a micro-explosion as well as the water gas effect, both can raise the combustion temperature and burning efficiency. By comparing the waste gas emission of different types of emulsified fuel, one can know that, the CO2 emission reduces approximately 14%, and NOx emission reduces above 46%, meaning the reduction of the exhaust gas is truly effective. From the exhaust temperature of tail pipe, the waste heat discharge also may reduce 27%, it is quite advantageous to the global warming as well as earth environmental protection.

Bayesian emulation for optimization in multi-step portfolio decisions

OpenAIRE

Irie, Kaoru; West, Mike

2016-01-01

We discuss the Bayesian emulation approach to computational solution of multi-step portfolio studies in financial time series. "Bayesian emulation for decisions" involves mapping the technical structure of a decision analysis problem to that of Bayesian inference in a purely synthetic "emulating" statistical model. This provides access to standard posterior analytic, simulation and optimization methods that yield indirect solutions of the decision problem. We develop this in time series portf...

Experimental investigation of the performance and emissions of diesel engines by a novel emulsified diesel fuel

International Nuclear Information System (INIS)

Chen, Zhenbin; Wang, Xiaochen; Pei, Yiqiang; Zhang, Chengliang; Xiao, Mingwei; He, Jinge

2015-01-01

Highlights: • A novel bio-fuel, glucose solution emulsified diesel fuel, is evaluated. • Emulsified diesel has comparable brake thermal efficiency. • NO X emissions decrease with emulsified fuel at all loads. • Soot emissions decrease with emulsified fuel except at a few operating points. - Abstract: The subject of this paper was to study the performance and emissions of two typical diesel engines using glucose solution emulsified diesel fuel. Emulsified diesel with a 15% glucose solution by mass fraction was used in diesel engines and compared with pure diesel. For the agricultural diesel engine, performance and emission characteristics were measured under various engine loads. The results showed that the brake thermal efficiencies were improved using emulsified diesel fuel. Emulsified fuel decreased NO x and soot emissions except at a few specific operating conditions. HydroCarbon (HC) and CO emissions were increased. For the automotive diesel engine, performance and emissions were measured using the 13-mode European Stationary Cycle (ESC). It was found that brake thermal efficiencies of emulsified diesel and pure diesel were comparable at 75% and 100% load. Soot emissions decreased significantly while NO x emissions decreased slightly. HC emissions increased while CO emissions decreased at some operating conditions

Feasibility and reliability of using an exoskeleton to emulate muscle contractures during walking.

Science.gov (United States)

Attias, M; Bonnefoy-Mazure, A; De Coulon, G; Cheze, L; Armand, S

2016-10-01

Contracture is a permanent shortening of the muscle-tendon-ligament complex that limits joint mobility. Contracture is involved in many diseases (cerebral palsy, stroke, etc.) and can impair walking and other activities of daily living. The purpose of this study was to quantify the reliability of an exoskeleton designed to emulate lower limb muscle contractures unilaterally and bilaterally during walking. An exoskeleton was built according to the following design criteria: adjustable to different morphologies; respect of the principal lines of muscular actions; placement of reflective markers on anatomical landmarks; and the ability to replicate the contractures of eight muscles of the lower limb unilaterally and bilaterally (psoas, rectus femoris, hamstring, hip adductors, gastrocnemius, soleus, tibialis posterior, and peroneus). Sixteen combinations of contractures were emulated on the unilateral and bilateral muscles of nine healthy participants. Two sessions of gait analysis were performed at weekly intervals to assess the reliability of the emulated contractures. Discrete variables were extracted from the kinematics to analyse the reliability. The exoskeleton did not affect normal walking when contractures were not emulated. Kinematic reliability varied from poor to excellent depending on the targeted muscle. Reliability was good for the bilateral and unilateral gastrocnemius, soleus, and tibialis posterior as well as the bilateral hamstring and unilateral hip adductors. The exoskeleton can be used to replicate contracture on healthy participants. The exoskeleton will allow us to differentiate primary and compensatory effects of muscle contractures on gait kinematics. Copyright © 2016 Elsevier B.V. All rights reserved.

LTE modem power consumption, SAR and RF signal strength emulation

DEFF Research Database (Denmark)

Musiige, Deogratius; Vincent, Laulagnet; Anton, François

2012-01-01

This paper presents a new methodology for emulating the LTE modem power consumption, emitted SAR and RF signal strength when transmitting an LTE signal. The inputs of the methodology are: modem logical/protocol commands, time advance, near-field specifier, and antenna characteristics. The power...... emulation model(s) are computed by a two layer 451 neural network based on physical power measurements. SAR is emulated by polynomial interpolation models based on FDTD simulations. The accuracies of the mathematical function approximations for the emulation models of power and SAR are 5.19% and 3...

Enhancement of emulsifier production by Curvularia lunata in cadmium, zinc and lead presence.

Science.gov (United States)

Paraszkiewicz, Katarzyna; Frycie, Aleksandra; Słaba, Mirosława; Długoński, Jerzy

2007-10-01

The influence of cadmium, zinc and lead on fungal emulsifier synthesis and on the growth of filamentous fungus Curvularia lunata has been studied. Tolerance to heavy metals established for C. lunata was additionally compared with the sensitivity exhibited by strains of Curvularia tuberculata and Paecilomyces marquandii-fungi which do not secrete compounds of emulsifying activity. Although C. lunata, as the only one out of all studied fungi, exhibited the lowest tolerance to heavy metals when grown on a solid medium (in conditions preventing emulsifier synthesis), it manifested the highest tolerance in liquid culture - in conditions allowing exopolymer production. Cadmium, zinc and lead presented in liquid medium up to a concentration of 15 mM had no negative effect on C. lunata growth and stimulated emulsifier synthesis. In the presence of 15 mM of heavy metals, both the emulsifier and 24-h-old growing mycelium exhibited maximum sorption capacities, which were determined as 18.2 +/- 2.67, 156.1 +/- 10.32 mg g(-1) for Cd2+, 22.2 +/- 3.40, 95.2 +/- 14.21 mg g(-1) for Zn2+ and 51.1 +/- 1.85, 230.0 +/- 28.47 mg g(-1) for Pb2+ respectively. The results obtained by us in this work indicate that the emulsifier acts as a protective compound increasing the ability of C. lunata to survive in heavy metal polluted environment. Enhancement of exopolymer synthesis in the presence of Cd2+, Zn2+ and Pb2+ may also suggest, at least to some extent, a metal-specific nature of emulsifier production in C. lunata. Due to accumulation capability and tolerance to heavy metals, C. lunata mycelium surrounded by the emulsifier could be applied for toxic metal removal.

Design of BLDCM emulator for transmission control units

Science.gov (United States)

Liu, Chang; He, Yongyi; Zhang, Bodong

2018-04-01

According to the testing requirements of the transmission control unit, a brushless DC motor emulating system is designed based on motor simulation and power hardware-in-the-loop. The discrete motor model is established and a real-time numerical method is designed to solve the motor states. The motor emulator directly interacts with power stage of the transmission control unit using a power-efficient circuit topology and is compatible with sensor-less control. Experiments on a laboratory prototype help to verify that the system can emulate the real motor currents and voltages whenever the motor is starting up or suddenly loaded.

Model of a photovoltaic panel emulator in MATLAB-Simulink

OpenAIRE

CAN, Hayrettin

2014-01-01

Being able to behave electrically similar to photovoltaic (PV) panels, PV emulator systems make it possible to perform different PV system tests under various operation conditions. In this paper, a model of a PV panel emulator is presented using the Power System Blockset under MATLAB-Simulink. The simulation of the emulator system is developed for testing a controller prior to a real-time implementation. The model can handle the dependence of all of the parameters in the model with ...

Phenolipids as antioxidants in emulsified systems

DEFF Research Database (Denmark)

Sørensen, Ann-Dorit Moltke; Bayrasy, Christelle; Laguerre, Mickäel

Lipid oxidation is a major issue in foods containing LC PUFA and substantial efforts have been made to protect lipids against oxidation. Recent studies carried out with phenolipids (lipophilized phenolics) in emulsified systems have shown that increased lipophilicity did not necessarily lead...... antioxidant effect has been shown to be influenced by the specific phenolic compound and the type of emulsion. The overall aim for our work was to evaluate phenolipids with different lipophilicity as antioxidants in emulsified food. In the study presented here caffeic, ferulic and coumaric acid were selected...... along with their corresponding alkyl esters (C4-C20). The methods used to evaluate the antioxidative effect of the different phenolipids were the CAT assay (o/w emulsion), antioxidant assays (DPPH, Iron chelating and reducing power) and partitioning studies. Moreover, the results from the CAT assay...

Hierarchical adaptive experimental design for Gaussian process emulators

International Nuclear Information System (INIS)

Busby, Daniel

2009-01-01

Large computer simulators have usually complex and nonlinear input output functions. This complicated input output relation can be analyzed by global sensitivity analysis; however, this usually requires massive Monte Carlo simulations. To effectively reduce the number of simulations, statistical techniques such as Gaussian process emulators can be adopted. The accuracy and reliability of these emulators strongly depend on the experimental design where suitable evaluation points are selected. In this paper a new sequential design strategy called hierarchical adaptive design is proposed to obtain an accurate emulator using the least possible number of simulations. The hierarchical design proposed in this paper is tested on various standard analytic functions and on a challenging reservoir forecasting application. Comparisons with standard one-stage designs such as maximin latin hypercube designs show that the hierarchical adaptive design produces a more accurate emulator with the same number of computer experiments. Moreover a stopping criterion is proposed that enables to perform the number of simulations necessary to obtain required approximation accuracy.

FED firmware interface testing with pixel phase 1 emulator

CERN Document Server

Kilpatrick, Matthew

2017-01-01

A hardware emulation of the CMS pixel detector phase 1 upgrade front-end electronics has been developed to test and validate the architecture of the back-end electronics (FED) firmware. The emulation is implemented on a Virtex 6 FPGA on the CERN GLIB uTCA platform, utilizing an 8-way SFP FPGA Mezzanine Card to drive compatible optical transmitters to the back-end electronics at 400 bps. The firmware emulates the complex functions of the phase 1 pixel readout chips (PSI46digv2 and PROC600) and token bit manager ASICs and allows for possible abnormalities that can occur in the output data stream. The emulation implements both fixed data patterns that are used as test vectors and realistic simulated data to drive the readout of the FED at the expected data and trigger rates. Testing software was developed to control the emulator and verify correct transmission of data and exception handling in the FED. An installation has been integrated into the pixel DAQ test system at CMS to be used for fast validation of F...

FED firmware interface testing with pixel phase 1 emulator

CERN Document Server

Kilpatrick, Matthew

2018-01-01

A hardware emulation of the CMS pixel detector phase 1 upgrade front-end electronics has been developed to test and validate the architecture of the back-end electronics (FED) firmware. The emulation is implemented on a Virtex 6 FPGA on the CERN GLIB uTCA platform, utilizing an 8-way SFP FPGA Mezzanine Card to drive compatible optical transmitters to the back-end electronics at 400 bps. The firmware emulates the complex functions of the phase 1 pixel readout chips (PSI46digv2 and PROC600) and token bit manager ASICs and allows for possible abnormalities that can occur in the output data stream. The emulation implements both fixed data patterns that are used as test vectors and realistic simulated data to drive the readout of the FED at the expected data and trigger rates. Testing software was developed to control the emulator and verify correct transmission of data and exception handling in the FED. An installation has been integrated into the pixel DAQ test system at CMS to be used for fast validation of F...

Effect of pre-emulsified sesame oil on physical-chemical and rheological properties of pork batters

Directory of Open Access Journals (Sweden)

Zhuang Li KANG

Full Text Available Abstract Physical-chemical and rheological properties of pork batters as affected by replacing pork back-fat with pre-emulsified sesame oil were investigated. Replacement of pork back-fat with pre-emulsified sesame oil, improved L* value, moisture and protein content, hardness, cohesiveness, and chewiness, declined a* value, fat content and energy, but not affect cooking yield. When used pre-emulsified sesame oil to replace pork back-fat 50%, the sample had the highest L* value and texture. According to the results of dynamic rheological, replaced pork back-fat by pre-emulsified sesame oil increased the storage modulus (G' values at 80 °C, and formed firm gel. The result of Low-field nuclear magnetic resonance (LF-NMR shown that the batters with pre-emulsified sesame oil had higher water holding capacity than the control. Overall, the batters with pre-emulsified sesame oil enabled lowering of fat and energy contents, making the pork batter had better texture.

Multichannel Digital Emulator of Radiation Detection Systems

International Nuclear Information System (INIS)

Abba, A.; Caponio, F.; Geraci, A.

2013-06-01

A digital system for emulating in real time signals from generic setups for radiation detection is presented. The instrument is not a pulse generator of recorded shapes but a synthesizer of random pulses compliant to programmable statistics for energy and occurrence time. Completely programmable procedures for emulation of noise, disturbances and reference level variation can be implemented. The instrument has been realized and fully tested. (authors)

Effects of prerigor pressurization on the emulsifying capacity of muscle protein

Energy Technology Data Exchange (ETDEWEB)

Elgasim, E.A.; Kennick, W.H.; Anglemier, A.F.; Elkhalifa, E.A.; Koohmaraie, M.

1982-05-01

The emulsifying capacities of pressure treated and control muscle homogenates, sarcoplasmic protein and myofibrillar proteins of ovine and bovine longissimus muscles were determined at 2, 6, 24 and 168 hr postmortem. The pH of the intact muscle, muscle homogenate and myofibrillar protein extract were taken at these times. Before onset of rigor mortis, the emulsifying capacity of muscle homogenate from the control samples was higher than the pressure treated samples. At 24 and 168 hr postmortem, the pressure treated and control samples were not significantly different (P>0.05) for emulsifying capacity. At 2 hr postmortem, the emulsifying capacity of myofibrillar protein extract from control samples was higher (P<0.05) than that from pressure treated samples; thereafter, the emulsification curve for the pressure treated samples was higher than that of the control. The emulsification capacity of sarcoplasmic proteins from control muscles was slightly, but consistently, higher than that from pressure treated muscles throughout the test period. Overall, the emulsification capacity of muscle proteins was not detrimentally affected by pressure treatment.

Advanced Machine Learning Emulators of Radiative Transfer Models

Science.gov (United States)

Camps-Valls, G.; Verrelst, J.; Martino, L.; Vicent, J.

2017-12-01

Physically-based model inversion methodologies are based on physical laws and established cause-effect relationships. A plethora of remote sensing applications rely on the physical inversion of a Radiative Transfer Model (RTM), which lead to physically meaningful bio-geo-physical parameter estimates. The process is however computationally expensive, needs expert knowledge for both the selection of the RTM, its parametrization and the the look-up table generation, as well as its inversion. Mimicking complex codes with statistical nonlinear machine learning algorithms has become the natural alternative very recently. Emulators are statistical constructs able to approximate the RTM, although at a fraction of the computational cost, providing an estimation of uncertainty, and estimations of the gradient or finite integral forms. We review the field and recent advances of emulation of RTMs with machine learning models. We posit Gaussian processes (GPs) as the proper framework to tackle the problem. Furthermore, we introduce an automatic methodology to construct emulators for costly RTMs. The Automatic Gaussian Process Emulator (AGAPE) methodology combines the interpolation capabilities of GPs with the accurate design of an acquisition function that favours sampling in low density regions and flatness of the interpolation function. We illustrate the good capabilities of our emulators in toy examples, leaf and canopy levels PROSPECT and PROSAIL RTMs, and for the construction of an optimal look-up-table for atmospheric correction based on MODTRAN5.

Influence of using emulsified diesel fuel on the performance and pollutants emitted from diesel engine

International Nuclear Information System (INIS)

Alahmer, Ali

2013-01-01

Highlights: • Emulsified diesel fuels with water content of range 0–30% by volume were prepared. • Effect emulsified diesel fuel on diesel engine performance and pollutant emissions. • Using emulsified fuel improves the diesel engine performance and reduces emissions. - Abstract: This manuscript investigates the effect of emulsified diesel fuel on the engine performance and on the main pollutant emissions for a water-cooled, four stroke, four cylinders, and direct injection diesel engine. Emulsified diesel fuels with water content of range 0–30% by volume were used. The experiments were conducted in the speed range from 1000 to 3000 rpm. It was found that, in general, the using emulsified fuel improves the engine performance and reduces emissions. While the brake specific fuel consumption (BSFC) has a minimum value at 5% water content and 2000 rpm. The torque (T), the break mean effective pressure (BMEP) and thermal efficiency (η th ) are found to have maximum values under these conditions. The emission CO 2 was found to increase with engine speed and to decrease with water content. NO x produced from emulsified fuel is significantly less than that produced from pure diesel under the same conditions. And as the percentage of water content in the emulsion increases, the emitted amount of oxygen also increases

RF power consumption emulation optimized with interval valued homotopies

DEFF Research Database (Denmark)

Musiige, Deogratius; Anton, François; Yatskevich, Vital

2011-01-01

This paper presents a methodology towards the emulation of the electrical power consumption of the RF device during the cellular phone/handset transmission mode using the LTE technology. The emulation methodology takes the physical environmental variables and the logical interface between...... the baseband and the RF system as inputs to compute the emulated power dissipation of the RF device. The emulated power, in between the measured points corresponding to the discrete values of the logical interface parameters is computed as a polynomial interpolation using polynomial basis functions....... The evaluation of polynomial and spline curve fitting models showed a respective divergence (test error) of 8% and 0.02% from the physically measured power consumption. The precisions of the instruments used for the physical measurements have been modeled as intervals. We have been able to model the power...

Memristor emulator causes dissimilarity on a coupled memristive systems

Science.gov (United States)

Sabarathinam, S.; Prasad, Awadhesh

2018-04-01

The memristor is known as abasic fourth passive solid state circuit element. Itgaining increasing attention to create the next generation electronic devices commonly used as fundamental chaotic circuit although often arbitrary (typically piecewise linear or cubic) fluxcharge characteristics. In thispresent work, the causes of the memristor emulator studied in a coupled memristive chaoticoscillator for the first time. We confirm that the emulator that allows synchronization between theoscillators and cause the dissimilarity between the systems when increasing the couplingstrength, and co-efficient of the memristor emulator. The detailed statistical analysis was performed to confirm such phenomenon.

The design of a network emulation and simulation laboratory

CSIR Research Space (South Africa)

Von Solms, S

2015-07-01

Full Text Available The development of the Network Emulation and Simulation Laboratory is motivated by the drive to contribute to the enhancement of the security and resilience of South Africa's critical information infrastructure. The goal of the Network Emulation...

Enzymatic preparation and characterization of soybean lecithin-based emulsifiers

International Nuclear Information System (INIS)

Reddy Jala, R.C.; Chen, B.; Li, H.; Zhang, Y.; Cheong, L.Z.; Yang, T.; Xu, X.

2016-01-01

Simple enzymatic methods were developed for the synthesis of lysolecithin, glycerolyzed lecithin and hydrolyzed lecithin. The products were characterized in terms of their acetone insoluble matter, hexane insoluble matter, moisture, phospholipid distribution and fatty acid composition. The HLB value ranges of different products with different acid values were detected. The efficiency of optimally hydrolyzed lecithin was examined at high calcium ion, low pH, and aqueous solutions and compared with commercially available standard lecithin-based emulsifiers. Overall, lysolecithin powder was proven to be the best emulsifier even at strong and medium acidic conditions. [es

Encapsulation of magnetic nanoparticles with polystyrene via emulsifier-free miniemulsion polymerization

International Nuclear Information System (INIS)

Faridi-Majidi, R.; Sharifi-Sanjani, N.; Agend, F.

2006-01-01

Magnetite nanoparticles (Fe 3 O 4 ), with an average size of about 10 nm, were encapsulated with polystyrene using a new method based on emulsifier-free miniemulsion polymerization in the presence of 2, 2' azobis (2-amidinopropane) dihydrochloride (V-50) as a cationic ionizable water-soluble initiator and hexadecane as a hydrophobe. Transmission electron microscopy (TEM) proved the presence of magnetite in polymer particles which appeared to be monodisperse in size, approximately 100-300 nm in diameter, through TEM and scanning electron microscopy (SEM). Thermogravimetric analysis (TGA) measurement was used to determine the percentage of magnetite in the products. The results of emulsifier-free miniemulsion polymerization were compared with those of conventional emulsifier-free emulsion polymerization using (V-50) as the initiator in both cases

Production of a New Emulsifier Material for the Formation Heavy Hydrocarbon/Water Emulsion

Directory of Open Access Journals (Sweden)

Afshin Farahbakhsh

2011-04-01

Full Text Available Emulsifiers are a unique class of compounds that have proved to have a variety of potential applications in formation of hydrocarbon in water emulsion, in enhancement of oil recovery and in the reduction of heavy oil viscosity. In this paper, a bio emulsifier was synthesized by a strain of Bacillus licheniformis and was separated by an autoclave and centrifugal process; the purification of bio emulsifier and the increase quality of product was done by adding sulfuric acid (H2SO4 (98% to the solution and centrifuging this compound again. This bio emulsifier has the property of emulsification to a wide range of heavy hydrocarbon to form a stable hydrocarbon-water emulsion. This bio emulsifier could reduce Iranian Nuroze high viscosity oil of about 10000 cP down to 250 cP. This means about 97% decreases in the viscosity. The emulsion stable this condition for 48 hr and the viscosity slowly increases to 4000cp until 192 hr. The stability of the oil in water emulsion during 48hr allows the heavy oil to be transported practically over lengthy distances or remain stable for long periods of time prior to utilization.

How to Party Like it’s 1999: Emulation for Everyone

Directory of Open Access Journals (Sweden)

Dianne Dietrich

2016-04-01

Full Text Available Emulated access of complex media has long been discussed, but there are very few instances in which complex, interactive, born-digital emulations are available to researchers. New York Public Library has made 1980-90's era video games from 5.25" floppy disks in the Timothy Leary Papers accessible via a DosBox emulator. These games appear in various stages of development and display the work of at least four of Leary's collaborators on the games. 56 disk images from the Leary Papers are currently emulated in the reading room. New York University has made late 1990s-mid 2000's era Photoshop files from the Jeremy Blake Papers accessible to researchers. The Blake Papers include over 300 pieces of media. Cornell University Library was awarded a grant from the NEH to analyze approximately 100 born-digital artworks created for CD-ROM from the Rose Goldsen Archive of New Media Art to develop preservation workflows, access strategies, and metadata frameworks. Rhizome has undertaken a number of emulation projects as a major part of its preservation strategy for born-digital artworks. In cooperation with the University of Freiburg in Germany, Rhizome recently restored several digital artworks for public access using a cloud-based emulation framework. This framework (bwFLA has been designed to facilitate the reenactments of software on a large scale, for internal use or public access. This paper will guide readers through how to implement emulation. Each of the institutions weigh in on oddities and idiosyncrasies they encountered throughout the process — from accession to access.

North-Karelian forest owners' attitude to nature-emulating forestry work methods

International Nuclear Information System (INIS)

Jouhiaho, A.

1999-01-01

The TTS-Institute conducted a mail-questionnaire study of forest owners' opinions in the Province of North Karelia (Pohjois-Karjala) concerning work methods as applied in silviculture and logging. In addition, the study looked into the matter of the forest owners' willingness to pay for the implementation of nature-emulating silviculture and logging. The response percentage was 57 % with 344 forest owners responding to the questionnaire. The majority of the forest owners understood nature-emulating silviculture and logging as worthwhile objectives and as actions aimed at economically advantageous outcomes. Nature-emulating work methods involve the use of method emulating the natural development dynamics of forest ecosystems and causing minimum disturbance to the ecosystem. The term 'nature-emulating' was also seen to include forest treatment with awareness of landscape management viewpoints. Less than half of the forest owners were willing to pay for the implementation of nature-emulating silviculture and logging. Of those willing to pay, half were prepared to pay an extra 6 - 10 % for sivicultural and 1 - 5 % for logging on top of the costs. (orig.)

On the network-based emulation of human visual search

NARCIS (Netherlands)

Gerrissen, J.F.

1991-01-01

We describe the design of a computer emulator of human visual search. The emulator mechanism is eventually meant to support ergonomic assessment of the effect of display structure and protocol on search performance. As regards target identification and localization, it mimics a number of

COSMIC EMULATION: FAST PREDICTIONS FOR THE GALAXY POWER SPECTRUM

Energy Technology Data Exchange (ETDEWEB)

Kwan, Juliana; Heitmann, Katrin; Habib, Salman; Frontiere, Nicholas; Pope, Adrian [High Energy Physics Division, Argonne National Laboratory, Lemont, IL 60439 (United States); Padmanabhan, Nikhil [Department of Physics, Yale University, 260 Whitney Ave., New Haven, CT 06520 (United States); Lawrence, Earl [Statistical Sciences, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Finkel, Hal [Argonne Leadership Computing Facility, Argonne National Laboratory, Lemont, IL 60439 (United States)

2015-09-01

The halo occupation distribution (HOD) approach has proven to be an effective method for modeling galaxy clustering and bias. In this approach, galaxies of a given type are probabilistically assigned to individual halos in N-body simulations. In this paper, we present a fast emulator for predicting the fully nonlinear galaxy–galaxy auto and galaxy–dark matter cross power spectrum and correlation function over a range of freely specifiable HOD modeling parameters. The emulator is constructed using results from 100 HOD models run on a large ΛCDM N-body simulation, with Gaussian Process interpolation applied to a PCA-based representation of the galaxy power spectrum. The total error is currently ∼1% in the auto correlations and ∼2% in the cross correlations from z = 1 to z = 0, over the considered parameter range. We use the emulator to investigate the accuracy of various analytic prescriptions for the galaxy power spectrum, parametric dependencies in the HOD model, and the behavior of galaxy bias as a function of HOD parameters. Additionally, we obtain fully nonlinear predictions for tangential shear correlations induced by galaxy–galaxy lensing from our galaxy–dark matter cross power spectrum emulator. All emulation products are publicly available at http://www.hep.anl.gov/cosmology/CosmicEmu/emu.html.

Development of the CELSS Emulator at NASA JSC

Science.gov (United States)

Cullingford, Hatice S.

1989-01-01

The Controlled Ecological Life Support System (CELSS) Emulator is under development at the NASA Johnson Space Center (JSC) with the purpose to investigate computer simulations of integrated CELSS operations involving humans, plants, and process machinery. This paper describes Version 1.0 of the CELSS Emulator that was initiated in 1988 on the JSC Multi Purpose Applications Console Test Bed as the simulation framework. The run module of the simulation system now contains a CELSS model called BLSS. The CELSS Emulator makes it possible to generate model data sets, store libraries of results for further analysis, and also display plots of model variables as a function of time. The progress of the project is presented with sample test runs and simulation display pages.

Single-step emulation of nonlinear fiber-optic link with gaussian mixture model

DEFF Research Database (Denmark)

Borkowski, Robert; Doberstein, Andy; Haisch, Hansjörg

2015-01-01

We use a fast and low-complexity statistical signal processing method to emulate nonlinear noise in fiber links. The proposed emulation technique stands in good agreement with the numerical NLSE simulation for 32 Gbaud DP-16QAM nonlinear transmission.......We use a fast and low-complexity statistical signal processing method to emulate nonlinear noise in fiber links. The proposed emulation technique stands in good agreement with the numerical NLSE simulation for 32 Gbaud DP-16QAM nonlinear transmission....

Real-time emulation of neural images in the outer retinal circuit.

Science.gov (United States)

Hasegawa, Jun; Yagi, Tetsuya

2008-12-01

We describe a novel real-time system that emulates the architecture and functionality of the vertebrate retina. This system reconstructs the neural images formed by the retinal neurons in real time by using a combination of analog and digital systems consisting of a neuromorphic silicon retina chip, a field-programmable gate array, and a digital computer. While the silicon retina carries out the spatial filtering of input images instantaneously, using the embedded resistive networks that emulate the receptive field structure of the outer retinal neurons, the digital computer carries out the temporal filtering of the spatially filtered images to emulate the dynamical properties of the outer retinal circuits. The emulations of the neural image, including 128 x 128 bipolar cells, are carried out at a frame rate of 62.5 Hz. The emulation of the response to the Hermann grid and a spot of light and an annulus of lights has demonstrated that the system responds as expected by previous physiological and psychophysical observations. Furthermore, the emulated dynamics of neural images in response to natural scenes revealed the complex nature of retinal neuron activity. We have concluded that the system reflects the spatiotemporal responses of bipolar cells in the vertebrate retina. The proposed emulation system is expected to aid in understanding the visual computation in the retina and the brain.

Encapsulation of magnetic nanoparticles with polystyrene via emulsifier-free miniemulsion polymerization

Energy Technology Data Exchange (ETDEWEB)

Faridi-Majidi, R. [School of Chemistry, University College of Science, Tehran University, Tehran (Iran, Islamic Republic of)]. E-mail: refaridi@khayam.ut.ac.ir; Sharifi-Sanjani, N. [School of Chemistry, University College of Science, Tehran University, Tehran (Iran, Islamic Republic of); Agend, F. [Malek-Ashtar University, Lavizan, Tehran (Iran, Islamic Republic of)

2006-09-25

Magnetite nanoparticles (Fe{sub 3}O{sub 4}), with an average size of about 10 nm, were encapsulated with polystyrene using a new method based on emulsifier-free miniemulsion polymerization in the presence of 2, 2' azobis (2-amidinopropane) dihydrochloride (V-50) as a cationic ionizable water-soluble initiator and hexadecane as a hydrophobe. Transmission electron microscopy (TEM) proved the presence of magnetite in polymer particles which appeared to be monodisperse in size, approximately 100-300 nm in diameter, through TEM and scanning electron microscopy (SEM). Thermogravimetric analysis (TGA) measurement was used to determine the percentage of magnetite in the products. The results of emulsifier-free miniemulsion polymerization were compared with those of conventional emulsifier-free emulsion polymerization using (V-50) as the initiator in both cases.

Panel Flutter Emulation Using a Few Concentrated Forces

Science.gov (United States)

Dhital, Kailash; Han, Jae-Hung

2018-04-01

The objective of this paper is to study the feasibility of panel flutter emulation using a few concentrated forces. The concentrated forces are considered to be equivalent to aerodynamic forces. The equivalence is carried out using surface spline method and principle of virtual work. The structural modeling of the plate is based on the classical plate theory and the aerodynamic modeling is based on the piston theory. The present approach differs from the linear panel flutter analysis in scheming the modal aerodynamics forces with unchanged structural properties. The solutions for the flutter problem are obtained numerically using the standard eigenvalue procedure. A few concentrated forces were considered with an optimization effort to decide their optimal locations. The optimization process is based on minimizing the error between the flutter bounds from emulated and linear flutter analysis method. The emulated flutter results for the square plate of four different boundary conditions using six concentrated forces are obtained with minimal error to the reference value. The results demonstrated the workability and viability of using concentrated forces in emulating real panel flutter. In addition, the paper includes the parametric studies of linear panel flutter whose proper literatures are not available.

Enzymatic preparation and characterization of soybean lecithin-based emulsifiers

Directory of Open Access Journals (Sweden)

R. C. Reddy Jala

2016-12-01

Full Text Available Simple enzymatic methods were developed for the synthesis of lysolecithin, glycerolyzed lecithin and hydrolyzed lecithin. The products were characterized in terms of their acetone insoluble matter, hexane insoluble matter, moisture, phospholipid distribution and fatty acid composition. The HLB value ranges of different products with different acid values were detected. The efficiency of optimally hydrolyzed lecithin was examined at high calcium ion, low pH, and aqueous solutions and compared with commercially available standard lecithin-based emulsifiers. Overall, lysolecithin powder was proven to be the best emulsifier even at strong and medium acidic conditions.

Experimental verification of on-chip CMOS fractional-order capacitor emulators

KAUST Repository

Tsirimokou, G.

2016-06-13

The experimental results from a fabricated integrated circuit of fractional-order capacitor emulators are reported. The chip contains emulators of capacitors of orders 0.3, 0.4, 0.5, 0.6 and 0.7 with nano-Farad pseudo-capacitances that can be adjusted through a bias current. Two off-chip capacitors are used to set the bandwidth of each emulator independently. The chip was designed in Austria microsystems (AMS) 0.35μ CMOS. © 2016 The Institution of Engineering and Technology.

Experimental verification of on-chip CMOS fractional-order capacitor emulators

KAUST Repository

Tsirimokou, G.; Psychalinos, C.; Salama, Khaled N.; Elwakil, A.S.

2016-01-01

The experimental results from a fabricated integrated circuit of fractional-order capacitor emulators are reported. The chip contains emulators of capacitors of orders 0.3, 0.4, 0.5, 0.6 and 0.7 with nano-Farad pseudo-capacitances that can be adjusted through a bias current. Two off-chip capacitors are used to set the bandwidth of each emulator independently. The chip was designed in Austria microsystems (AMS) 0.35μ CMOS. © 2016 The Institution of Engineering and Technology.

EmuStack: An OpenStack-Based DTN Network Emulation Platform (Extended Version

Directory of Open Access Journals (Sweden)

Haifeng Li

2016-01-01

Full Text Available With the advancement of computing and network virtualization technology, the networking research community shows great interest in network emulation. Compared with network simulation, network emulation can provide more relevant and comprehensive details. In this paper, EmuStack, a large-scale real-time emulation platform for Delay Tolerant Network (DTN, is proposed. EmuStack aims at empowering network emulation to become as simple as network simulation. Based on OpenStack, distributed synchronous emulation modules are developed to enable EmuStack to implement synchronous and dynamic, precise, and real-time network emulation. Meanwhile, the lightweight approach of using Docker container technology and network namespaces allows EmuStack to support a (up to hundreds of nodes large-scale topology with only several physical nodes. In addition, EmuStack integrates the Linux Traffic Control (TC tools with OpenStack for managing and emulating the virtual link characteristics which include variable bandwidth, delay, loss, jitter, reordering, and duplication. Finally, experiences with our initial implementation suggest the ability to run and debug experimental network protocol in real time. EmuStack environment would bring qualitative change in network research works.

Photovoltaic sources modeling and emulation

CERN Document Server

Piazza, Maria Carmela Di

2012-01-01

This book offers an extensive introduction to the modeling of photovoltaic generators and their emulation by means of power electronic converters will aid in understanding and improving design and setup of new PV plants.

Evaluating the Limits of Network Topology Inference Via Virtualized Network Emulation

Science.gov (United States)

2015-06-01

virtualized environment. First, we automatically build topological ground truth according to various network generation models and create emulated Cisco ...to various network generation models and create emulated Cisco router networks by leveraging and modifying existing emulation software. We then au... markets , to verifying compliance with policy, as in recent “network neutrality” rules established in the United States. The Internet is a network of

Protein nativity explains emulsifying properties of aqueous extracted protein components from yellow pea

NARCIS (Netherlands)

Geerts, Marlies E.J.; Nikiforidis, Constantinos V.; Goot, van der Atze Jan; Padt, van der Albert

2017-01-01

In this paper, the emulsifying properties of a protein-enriched fraction from pea are unravelled. The emulsifying properties of mildly fractionated protein fractions from yellow pea and compared to those of commercial pea protein isolate. The emulsion stability of an oil-in-water emulsions were

The characteristic of spray using diesel water emulsified fuel in a diesel engine

International Nuclear Information System (INIS)

Park, Sangki; Woo, Seungchul; Kim, Hyungik; Lee, Kihyung

2016-01-01

Highlights: • Water in oil emulsion is produced using ceramic membrane. • Surfactant type affect stability performance and droplet size distribution. • Evaporation characteristic of DE is poor compared with neat diesel. • Coefficient of variation maintains below 2.0% both DE and neat diesel. - Abstract: In this study, it was applied to the diesel–water emulsified (DE) fuel that carried out the experiment for the characteristic of sprat using diesel water emulsified fuel in a diesel engine, and the possibility of its application to conventional diesel engines was evaluated from the fundamental characteristics of diesel–water emulsified fuel. According to the results of the spray characteristics such as spray penetration and spray distribution were measured in the experiment, and then analyzed through digital image processing. The DEs were applied to actual diesel engines and their combustion, emission, and fuel consumption characteristics were compared with those of diesel. The results showed that the experiments were confirmed as the spray atomization characteristics at the various emulsified fuels.

Characteristics of W/O emulsions containing polymeric emulsifier PEG 30-dipolyhydroxystearate

Directory of Open Access Journals (Sweden)

Milinković Jelena R.

2016-01-01

Full Text Available Water-in-oil (W/O emulsions are dispersed systems which are often used in the pharmaceutical, cosmetic and food industries as products, or as carriers of active substances. It is well known that they are very unstable, so that selection of the emulsifier and properties of the oil and water phase are main factors affecting their stability. The aim of this paper was to examine the possibility of application of a lipophilic, polymeric emulsifier, PEG 30-dipolyhydroxystearate (CithrolTM DPHS, for stabilization of W/O emulsions. Behaviour of the emulsifier at W/O interfaces was determined by means of tensiometry. A series of emulsions were prepared with 20% (w/w of water and different types of oil. Droplet size, droplet size distribution, viscosity, and sedimentation stability during 30 days of storage at room temperature of the emulsions prepared with paraffin oil, olive oil, grape seed oil, and medium-chain triglycerides, stabilized with 1% CithrolTM DPHS, were determined. All investigated emulsions were stable for 30 days, except the one prepared with paraffin oil. The results of this study confirmed that PEG 30-dipolyhydroxylstearate is a good emulsifier and stabilizer of W/O emulsions which contain different types of oil. [Projekat Ministarstva nauke Republike Srbije, br. III46010

QERx- A Faster than Real-Time Emulator for Space Processors

Science.gov (United States)

Carvalho, B.; Pidgeon, A.; Robinson, P.

2012-08-01

Developing software for space systems is challenging. Especially because, in order to be sure it can cope with the harshness of the environment and the imperative requirements and constrains imposed by the platform were it will run, it needs to be tested exhaustively. Software Validation Facilities (SVF) are known to the industry and developers, and provide the means to run the On-Board Software (OBSW) in a realistic environment, allowing the development team to debug and test the software.But the challenge is to be able to keep up with the performance of the new processors (LEON2 and LEON3), which need to be emulated within the SVF. Such processor emulators are also used in Operational Simulators, used to support mission preparation and train mission operators. These simulators mimic the satellite and its behaviour, as realistically as possible. For test/operational efficiency reasons and because they will need to interact with external systems, both these uses cases require the processor emulators to provide real-time, or faster, performance.It is known to the industry that the performance of previously available emulators is not enough to cope with the performance of the new processors available in the market. SciSys approached this problem with dynamic translation technology trying to keep costs down by avoiding a hardware solution and keeping the integration flexibility of full software emulation.SciSys presented “QERx: A High Performance Emulator for Software Validation and Simulations” [1], in a previous DASIA event. Since then that idea has evolved and QERx has been successfully validated. SciSys is now presenting QERx as a product that can be tailored to fit different emulation needs. This paper will present QERx latest developments and current status.

Scalable and reusable emulator for evaluating the performance of SS7 networks

Science.gov (United States)

Lazar, Aurel A.; Tseng, Kent H.; Lim, Koon Seng; Choe, Winston

1994-04-01

A scalable and reusable emulator was designed and implemented for studying the behavior of SS7 networks. The emulator design was largely based on public domain software. It was developed on top of an environment supported by PVM, the Parallel Virtual Machine, and managed by OSIMIS-the OSI Management Information Service platform. The emulator runs on top of a commercially available ATM LAN interconnecting engineering workstations. As a case study for evaluating the emulator, the behavior of the Singapore National SS7 Network under fault and unbalanced loading conditions was investigated.

DDM Workload Emulation

Science.gov (United States)

Vigne, R.; Schikuta, E.; Garonne, V.; Stewart, G.; Barisits, M.; Beermann, T.; Lassnig, M.; Serfon, C.; Goossens, L.; Nairz, A.; Atlas Collaboration

2014-06-01

Rucio is the successor of the current Don Quijote 2 (DQ2) system for the distributed data management (DDM) system of the ATLAS experiment. The reasons for replacing DQ2 are manifold, but besides high maintenance costs and architectural limitations, scalability concerns are on top of the list. Current expectations are that the amount of data will be three to four times as it is today by the end of 2014. Further is the availability of more powerful computing resources pushing additional pressure on the DDM system as it increases the demands on data provisioning. Although DQ2 is capable of handling the current workload, it is already at its limits. To ensure that Rucio will be up to the expected workload, a way to emulate it is needed. To do so, first the current workload, observed in DQ2, must be understood in order to scale it up to future expectations. The paper discusses how selected core concepts are applied to the workload of the experiment and how knowledge about the current workload is derived from various sources (e.g. analysing the central file catalogue logs). Finally a description of the implemented emulation framework, used for stress-testing Rucio, is given.

DDM workload emulation

International Nuclear Information System (INIS)

Vigne, R; Schikuta, E; Garonne, V; Stewart, G; Barisits, M; Beermann, T; Lassnig, M; Serfon, C; Goossens, L; Nairz, A

2014-01-01

Rucio is the successor of the current Don Quijote 2 (DQ2) system for the distributed data management (DDM) system of the ATLAS experiment. The reasons for replacing DQ2 are manifold, but besides high maintenance costs and architectural limitations, scalability concerns are on top of the list. Current expectations are that the amount of data will be three to four times as it is today by the end of 2014. Further is the availability of more powerful computing resources pushing additional pressure on the DDM system as it increases the demands on data provisioning. Although DQ2 is capable of handling the current workload, it is already at its limits. To ensure that Rucio will be up to the expected workload, a way to emulate it is needed. To do so, first the current workload, observed in DQ2, must be understood in order to scale it up to future expectations. The paper discusses how selected core concepts are applied to the workload of the experiment and how knowledge about the current workload is derived from various sources (e.g. analysing the central file catalogue logs). Finally a description of the implemented emulation framework, used for stress-testing Rucio, is given.

Preparation and characterization of a self-emulsifying pellet formulation.

Science.gov (United States)

Abdalla, Ahmed; Mäder, Karsten

2007-05-01

The purpose of the current study is to investigate the feasibility of producing solid self-emulsifying pellets using the extrusion/spheronization technique. Pellets were made from a mixture of C18 partial glycerides, Solutol HS15 and microcrystalline cellulose. Pellets with good physical properties (size, shape, friability) and self-emulsifying properties were produced. The pellets were, in contrast to pellets lacking Solutol, able to transfer a lipophilic dye and a spin probe into the aqueous media. The release kinetics and the microenvironment of the pellets during the release process were assessed using electron spin resonance (ESR) spectroscopy. The ESR results showed that the hydrophobic spin probe was localized mainly in the lipid environment all over the release time. Furthermore, the formulation was capable of accelerating the release of the drug diazepam and achieving a diazepam concentration above its saturation solubility. In conclusion, spherical pellets with low friability and self-emulsifying properties can be produced by the standard extrusion/spheronization technique. The pellets are capable of transfering lipophilic compounds into the aqueous phase and have a high potential to increase the bioavailability of lipophilic drugs.

An FPGA-Based Quantum Computing Emulation Framework Based on Serial-Parallel Architecture

Directory of Open Access Journals (Sweden)

Y. H. Lee

2016-01-01

Full Text Available Hardware emulation of quantum systems can mimic more efficiently the parallel behaviour of quantum computations, thus allowing higher processing speed-up than software simulations. In this paper, an efficient hardware emulation method that employs a serial-parallel hardware architecture targeted for field programmable gate array (FPGA is proposed. Quantum Fourier transform and Grover’s search are chosen as case studies in this work since they are the core of many useful quantum algorithms. Experimental work shows that, with the proposed emulation architecture, a linear reduction in resource utilization is attained against the pipeline implementations proposed in prior works. The proposed work contributes to the formulation of a proof-of-concept baseline FPGA emulation framework with optimization on datapath designs that can be extended to emulate practical large-scale quantum circuits.

CHAIN EXTENDER AND EMULSIFIER APPLICATION IN IRON ORE FLOTATION

Directory of Open Access Journals (Sweden)

José Pedro da Silva

2013-06-01

Full Text Available The present study aims to evaluate the reverse flotation performance of iron ore, using collector (amine, in the presence and absence of chain extender (diesel oil and emulsifier (sodium lauryl sulfate.Six tests were realized with duplicate. Tests using amine, diesel oil and sodium lauryl sulphate show the better results, with metallurgical recovery of 91.82% and the concentrate silica equal 1.68%. Thus, it is found that the use of emulsifier and chain extender together with the amine, shows better results in the flotation, in terms of metal recovery and selectivity, when compared to using only amine or amine and diesel oil.

A Mobile Augmented Reality Emulator for Android

Directory of Open Access Journals (Sweden)

Donald Munro

2017-07-01

Full Text Available Augmented Reality (AR provides a fusion of the real and virtual worlds by superimposing virtual objects on real world scenery. The implementation of AR on mobile devices is known as Mobile Augmented Reality (MAR. MAR is in its infancy and MAR development software is in the process of maturing. Dating back to the origin of Computer Science as an independent field, software development tools have been an integral part of the process of software creation. MAR, being a relatively new technology, is still lacking such related software development tools. With the rapid progression of mobile devices, the development of MAR applications fusing advanced Computer Vision techniques with mobile device sensors have become increasingly feasible. However, testing and debugging of MAR applications present a new challenge in that they require the developer be at the location that is being augmented at some point during the development process. In this research study, a MAR recorder application was developed as well as emulation class libraries for Android devices that allows the recording and off-site playback of video, location and motion sensor data. The research objective was to provide a software emulator which provides debugging, testing and prototyping capabilities for a MAR application including the ability to emulate the combination of computer vision with locational and motion sensors using previously recorded data. The emulator was evaluated using different mobile technologies. The results indicate that this research could assist developers of MAR applications to implement applications more rapidly, without being at the location.

An Integrated Methodology for Emulsified Formulated Product Design

DEFF Research Database (Denmark)

Mattei, Michele

are mixed together to determine the desired emulsified product. They are still mainly designed and analysed through trial - and - error based exper- imental techniques, therefore a systematic approach , integrating model-based as well a s experiment - based techniques, for design of these products could......The consumer oriented chemical based products are used every day by millions of people. They are structured products constituted of numerous chemicals, and many of them, especially household and personal care products, are emulsions where active ingredients, solvents, additives and surfactants...... significantly reduce both time and cost connected to product development by doing only the necessary experi- ments , and ensuring chances for innovation . The main contribution of this project i s the development of an integrated methodology for the design of emulsified formulated products. The methodology...

Multiprocessor Priority Ceiling Emulation for Safety-Critical Java

DEFF Research Database (Denmark)

Strøm, Torur Biskopstø; Schoeberl, Martin

2015-01-01

Priority ceiling emulation has preferable properties on uniprocessor systems, such as avoiding priority inversion and being deadlock free. This has made it a popular locking protocol. According to the safety-critical Java specication, priority ceiling emulation is a requirement for implementations....... However, implementing the protocol for multiprocessor systemsis more complex so implementations might perform worse than non-preemptive implementations. In this paper we compare two multiprocessor lock implementations with hardware support for the Java optimized processor: non-preemptive locking...

The emulsifying and tribological properties of modified graphene oxide in oil-in-water emulsion

NARCIS (Netherlands)

Wu, Yinglei; Zeng, Xiangqiong; Ren, Tianhui; de Vries, Erik G.; van der Heide, Emile

2017-01-01

Graphene oxide (GO) was asymmetric chemically modified with myristyltrimethylammonium bromide (TTAB) to get modified graphene oxide (MGO). This MGO was used as an emulsifier and additive in oil-in-water emulsion. The emulsifying tests showed MGO greatly improved the stability of base emulsion and

Stability Emulsion and Sensory Characteristics Low Fat Mayonnaise Using Kefir as Emulsifier Replacer

Directory of Open Access Journals (Sweden)

Herly Evanuarini

2017-03-01

Full Text Available Mayonnaise is a kind of semi solid oil in water (o/w emulsion which containing pasteurized egg yolk as an emulsifier. The consumers have demanded that the use of egg yolk be reduced. Kefir was used to develop a low fat mayonnaise as emulsifier replacer to egg yolk. The objective of this research was to observe the emulsion stability, sensory characteristics of low fat mayonnaise prepare during kefir as emulsifier replacer. The research method was using experimental design. The result showed that formulation of low fat mayonnaise by using Rice bran oil 40%, kefir 20% produces the optimal low fat mayonnaise in emulsion stability and accepted by the panelist.

Influence of gamma radiation and freezing on emulsifying capacity of trash fish muscle

International Nuclear Information System (INIS)

Ghosh, S.K.; Lewis, N.F.

1979-01-01

The authors examined meat taken from seven different types of fish to determine its emulsifying capacity, i.e. once after treatment with γ-rays and once after frozen storage. The results showed that the shelf life of refrigerated trash fish with a low γ-radiation dose (100 Krad), which hardly affected the emulsifying capacity of the fishmeat, can be considerably extended. Trash fis frozen at -18 0 C should (apart from a few exceptions) be processed at the latest after one month's storage. Generally speaking however the emulsifying capacity of the fish musculature fell much more quickly in all species of fish after irradiation than it did during frozen storage. (orig./MG) 891 MG/orig.- 892 HIS [de

Effect of Hydrocolloids and Emulsifiers on Baking Quality of Composite Cassava-Maize-Wheat Breads

Directory of Open Access Journals (Sweden)

Maria Eduardo

2014-01-01

Full Text Available Cassava is widely available worldwide but bread quality is impaired when cassava is used in the bread formulation. To overcome this problem, different improvers were tested in the preparation of composite cassava-maize-wheat (CMW breads. Emulsifiers, diacetyl tartic acid ester of monoglycerides (DATEM, sodium stearoyl-2-lactylate (SSL, and lecithin (LC; and hydrocolloids, carboxymethylcellulose (CMC and high-methylated pectin (HM pectin were added during dough preparation of the composite flours (cassava-maize-wheat, 40 : 10 : 50. Each emulsifier was tested in combination with the hydrocolloids at levels of 0.1, 0.3, and 0.5% while hydrocolloids were used at a level of 3%. Bread quality attributes such as specific loaf volume, crust colour, crumb moisture, and firmness were measured. The specific volume of the fresh breads significantly improved with the addition of hydrocolloids (7.5 and 13% and in combination with emulsifiers (from 7.9 to 27% compared with bread produced without improvers. A significant improvement of brownness index and firmness of the composite flours breads was achieved with the addition of hydrocolloids and emulsifiers. The results show that emulsifiers and hydrocolloids can significantly improve the baking quality of CMW breads and thereby enhance the potential for using locally produced flours in bread baking.

Effects of water-emulsified fuel on a diesel engine generator's thermal efficiency and exhaust.

Science.gov (United States)

Syu, Jin-Yuan; Chang, Yuan-Yi; Tseng, Chao-Heng; Yan, Yeou-Lih; Chang, Yu-Min; Chen, Chih-Chieh; Lin, Wen-Yinn

2014-08-01

Water-emulsified diesel has proven itself as a technically sufficient improvement fuel to improve diesel engine fuel combustion emissions and engine performance. However, it has seldom been used in light-duty diesel engines. Therefore, this paper focuses on an investigation into the thermal efficiency and pollution emission analysis of a light-duty diesel engine generator fueled with different water content emulsified diesel fuels (WD, including WD-0, WD-5, WD-10, and WD-15). In this study, nitric oxide, carbon monoxide, hydrocarbons, and carbon dioxide were analyzed by a vehicle emission gas analyzer and the particle size and number concentration were measured by an electrical low-pressure impactor. In addition, engine loading and fuel consumption were also measured to calculate the thermal efficiency. Measurement results suggested that water-emulsified diesel was useful to improve the thermal efficiency and the exhaust emission of a diesel engine. Obviously, the thermal efficiency was increased about 1.2 to 19.9%. In addition, water-emulsified diesel leads to a significant reduction of nitric oxide emission (less by about 18.3 to 45.4%). However the particle number concentration emission might be increased if the loading of the generator becomes lower than or equal to 1800 W. In addition, exhaust particle size distributions were shifted toward larger particles at high loading. The consequence of this research proposed that the water-emulsified diesel was useful to improve the engine performance and some of exhaust emissions, especially the NO emission reduction. Implications: The accumulated test results provide a good basis to resolve the corresponding pollutants emitted from a light-duty diesel engine generator. By measuring and analyzing transforms of exhaust pollutant from this engine generator, the effects of water-emulsified diesel fuel and loading on emission characteristics might be more clear. Understanding reduction of pollutant emissions during the use

Wireless Network Emulation System (WiNE)

National Research Council Canada - National Science Library

Holland, Gavin

2005-01-01

.... Our approach to this problem is to develop a tool that emulates a field-test environment in the lab, so technologies under consideration can migrate from coarse simulation models to actual code...

The Use and Abuses of Emulation as a Pedagogical Practice

Science.gov (United States)

Jonas, Mark E.; Chambers, Drew W.

2017-01-01

From the late eighteenth through the end of the nineteenth century, educational philosophers and practitioners debated the benefits and shortcomings of the use of emulation in schools. During this period, "emulation" referred to a pedagogy that leveraged comparisons between students as a tool to motivate them to higher achievement. Many…

Production and Application of Lysozyme-Gum Arabic Conjugate in Mayonnaise as a Natural Preservative and Emulsifier

DEFF Research Database (Denmark)

Hashemi, Marjan M.; Aminlari, Mahmoud; Forouzan, Mehdi M.

2018-01-01

Nowadays demand for food products made by natural sources is rising so fast. In this work Lysozyme (Lyz) was conjugated with gum Arabic (GA) in order to be applied in mayonnaise, at which the presence of both preservative and emulsifier is essential. Interestingly, the Lyz-GA conjugate exhibited...... possible the application of a natural preservative and emulsifier in food and pharmaceutical industries, whereas Lyz alone does not have a broad-spectrum antibacterial activity or emulsifying properties....... improved functional properties and antibacterial activity. In order to approve the results of this study, the Lyz-GA conjugate was applied to mayonnaise as a natural preservative and emulsifier. Application of the Lzy-GA conjugate in mayonnaise expedited the death rate of both S. aureus and E. coli K-12...

Demonstration of Emulator-Based Bayesian Calibration of Safety Analysis Codes: Theory and Formulation

Directory of Open Access Journals (Sweden)

Joseph P. Yurko

2015-01-01

Full Text Available System codes for simulation of safety performance of nuclear plants may contain parameters whose values are not known very accurately. New information from tests or operating experience is incorporated into safety codes by a process known as calibration, which reduces uncertainty in the output of the code and thereby improves its support for decision-making. The work reported here implements several improvements on classic calibration techniques afforded by modern analysis techniques. The key innovation has come from development of code surrogate model (or code emulator construction and prediction algorithms. Use of a fast emulator makes the calibration processes used here with Markov Chain Monte Carlo (MCMC sampling feasible. This work uses Gaussian Process (GP based emulators, which have been used previously to emulate computer codes in the nuclear field. The present work describes the formulation of an emulator that incorporates GPs into a factor analysis-type or pattern recognition-type model. This “function factorization” Gaussian Process (FFGP model allows overcoming limitations present in standard GP emulators, thereby improving both accuracy and speed of the emulator-based calibration process. Calibration of a friction-factor example using a Method of Manufactured Solution is performed to illustrate key properties of the FFGP based process.

Emulation of Narrowband Powerline Data Transmission Channels and Evaluation of PLC Systems

OpenAIRE

Liu, Wenqing

2013-01-01

This work proposes advanced emulation of the physical layer behavior of NB-PLC channels and the application of a channel emulator for the evaluation of NB-PLC systems. In addition, test procedures and reference channels are proposed to improve efficiency and accuracy in the system evaluation and classification. This work shows that the channel emulator-based solution opens new ways toward flexible, reliable and technology-independent performance assessment of PLC modems.

Boosting flood warning schemes with fast emulator of detailed hydrodynamic models

Science.gov (United States)

Bellos, V.; Carbajal, J. P.; Leitao, J. P.

2017-12-01

Floods are among the most destructive catastrophic events and their frequency has incremented over the last decades. To reduce flood impact and risks, flood warning schemes are installed in flood prone areas. Frequently, these schemes are based on numerical models which quickly provide predictions of water levels and other relevant observables. However, the high complexity of flood wave propagation in the real world and the need of accurate predictions in urban environments or in floodplains hinders the use of detailed simulators. This sets the difficulty, we need fast predictions that meet the accuracy requirements. Most physics based detailed simulators although accurate, will not fulfill the speed demand. Even if High Performance Computing techniques are used (the magnitude of required simulation time is minutes/hours). As a consequence, most flood warning schemes are based in coarse ad-hoc approximations that cannot take advantage a detailed hydrodynamic simulation. In this work, we present a methodology for developing a flood warning scheme using an Gaussian Processes based emulator of a detailed hydrodynamic model. The methodology consists of two main stages: 1) offline stage to build the emulator; 2) online stage using the emulator to predict and generate warnings. The offline stage consists of the following steps: a) definition of the critical sites of the area under study, and the specification of the observables to predict at those sites, e.g. water depth, flow velocity, etc.; b) generation of a detailed simulation dataset to train the emulator; c) calibration of the required parameters (if measurements are available). The online stage is carried on using the emulator to predict the relevant observables quickly, and the detailed simulator is used in parallel to verify key predictions of the emulator. The speed gain given by the emulator allows also to quantify uncertainty in predictions using ensemble methods. The above methodology is applied in real

LTE HetNet Mobility Performance Through Emulation with Commercial Smartphones

DEFF Research Database (Denmark)

Jensen, Anders Riis; Pedersen, Klaus I.; Lauridsen, Mads

2014-01-01

In this paper we introduce a laboratory emulation setup for evaluation of Long Term Evolution (LTE) mobility performance in a co-channel heterogeneous network (HetNet). The setup consists of two eNodeB emulators, signal faders and release 9 LTE User Equipment (UE). It is shown how the LTE HetNet ...

Hardware Locks with Priority Ceiling Emulation for a Java Chip-Multiprocessor

DEFF Research Database (Denmark)

Strøm, Torur Biskopstø; Schoeberl, Martin

2015-01-01

According to the safety-critical Java specification, priority ceiling emulation is a requirement for implementations, as it has preferable properties, such as avoiding priority inversion and being deadlock free on uni-core systems. In this paper we explore our hardware supported implementation...... of priority ceiling emulation on the multicore Java optimized processor, and compare it to the existing hardware locks on the Java optimized processor. We find that the additional overhead for priority ceiling emulation on a multicore processor is several times higher than simpler, non-premptive locks, mainly...

Effect of nonionic compound emulsifiers Tween80 and Span80 on the properties of microencapsulated phase change materials.

Science.gov (United States)

Zhan, Shiping; Zhou, Zhiyi; Wang, Weijing; Zhao, Qicheng; Hou, Weimin

2014-01-01

In this article, the nonionic compound emulsifiers Tween80 and Span80 were used to prepare microcapsules containing phase change materials (microPCMs) with melamine-formaldehyde (MF) shells by in situ polymerization method. The effects of compound emulsifiers Tween80 and Span80 on the structure, morphologies and properties of microPCMs containing paraffin were studied. SEM morphological investigation suggests that a complex of Tween80 and Span80 as emulsifiers are optimal for the fabrication of microPCMs in this study compared to Tween60 or OP-10. The diameter distributions of microPCMs synthesized with different amounts of compound emulsifiers are uniform, whereas compound emulsifiers' amount affect the mean diameter of microPCMs decreasing from 5.34 to 3.05 µm. These microPCMs with the core/shell weight ratio 3/1 have smoother surface and a higher core content of 68.7% than other core/shell ratio. Anti-osmosis measurements indicate that microPCMs have good compactness and stable performance compared to those synthesized by one type of emulsifier.

Thermal, emulsifying and rheological properties of polysaccharides sequentially extracted from Vaccinium bracteatum Thunb leaves.

Science.gov (United States)

Xu, Qi-Xin; Shi, Jun-Jun; Zhang, Jian-Guo; Li, Ling; Jiang, Li; Wei, Zhao-Jun

2016-12-01

Plant polysaccharides are widely used in food industry as thickening and gelling agents and these attributes largely depend on their thermal, emulsifying and rheological properties. As known, the extraction methods always bring about the diversification of property and functions of polysaccharides. Thus, the Vaccinium bracteatum Thunb leaves polysaccharides (VBTLP) were sequentially extracted using hot buffer (HBSS), chelating agent (CHSS), dilute alkaline (DASS) and concentrated alkaline (CASS). The thermal, emulsifying and rheological properties of VBTLP were investigated in the present study. Within the range of 20-225°C, CHSS showed the highest peak temperature, whereas HBSS displayed the highest endothermic enthalpy and highest emulsifying activity, while, CASS showed the longest emulsifying stability. The VBTLP solutions exhibited non-Newtonian shear-thinning behavior within the concentrations of 0.6-2.5%. The apparent viscosity of VBTLP solution decreased under following conditions: acidic pH (4.0), alkaline pH (10.0), in the presence of Ca 2+ and at high temperature, while it increased in the presence of Na + and at freezing conditions. The modulus G' and G″ of VBTLP solutions were increased with increasing oscillation frequency, and the crossover frequency shifted to lower values when the polysaccharide content increased. The above results of thermal, emulsifying and rheological properties of VBTLPs supplied the basis for V. bracteatum leaves in potential industrial applications of foods. Copyright © 2016 Elsevier B.V. All rights reserved.

Emulating Industrial Control System Field Devices Using Gumstix Technology

Science.gov (United States)

2012-06-01

Security mechanisms (e.g., intrusion detection systems, antivirus and honeypots) are employed in traditional Information Technology (IT) systems to detect...can be used to determine the vendor of the device if the fingerprinting is done on a local segment. 2.8 Emulation Emulation is software or...Each of the honeypots in the network can be different systems ranging from Windows workstations to IIS web servers to Cisco routers. Honeynets rely

Effects of Emulsifiers on Preparing Spherical Urea-Formaldehyde Paraffin Capsules Modified by β-Cyclodextrin for Energy Storage

Directory of Open Access Journals (Sweden)

Xin Yu

2014-01-01

Full Text Available Urea-formaldehyde (UF paraffin capsules (B-UPCS modified by β-cyclodextrin (β-CD were successfully prepared with excellent energy storage capacity using different emulsifiers. B-UPCS were characterized by FT-IR, DSC SEM, optical microscopy, and laser particle size distribution analyzer. The effects of different emulsifiers and the stirring rate of emulsion on the microstructure, average particle diameter, and the content of paraffin were discussed in details. The results show that OP-10 for use with PCMs as emulsifier has a better emulsifying capacity, thermal stability, and mechanical stirring stability than SDBS for use with PCMs as emulsifier. As a result, the optimum dosage of OP-10 was 3% to 7%, and the suitable stirring rate of emulsion was 7500 to 12500 rpm. At this time, the spherical particle diameter of B-UPCS was about 1.0 μm, the paraffin content was 78%, and the enthalpy of B-UPCS can reach 161.0 J/g.

DCS emulator development for the ACR-1000 simulator

International Nuclear Information System (INIS)

Nakashima, Y.; Trueman, R.; Ishii, K.

2010-01-01

Nuclear Power Plant (NPP) simulators are the main means for operator training and as such are a crucial part of the NPP operation life-cycle. Hitachi, Ltd., Information and Control Systems Company (henceforth 'Hitachi') is the preferred DCS and DCS emulator developer and supplier for the ACR-1000 NPP control system. Hitachi's concept for the DCS (distributed control system) portion of the ACR-1000 simulator is 'total emulation of the DCS' by software. This paper will review the current status of the technical development and the major project milestones. (author)

Inexplicit Learning: Transferring Knowledge through Visual and Emulative practices

Directory of Open Access Journals (Sweden)

Koumudi Patil

2017-12-01

Full Text Available This study attempts to understand how expert knowledge is transmitted in the absence or lack of explicit and formal means of knowledge acquisition, with particular interest in the evolved relationship of a master-apprentice, observable in pockets of traditional communities of practice. An ethnographic study based on content analysis of the transcriptions of members of a craft community from Varanasi, India has been used to strengthen the undermined pedagogical role of observation and emulation in the transfer of inexplicit knowledge. It is argued that in-situ observation and emulation foster situations for facilitating co-production of knowledge, further implying co-authorship. Gaining community membership in craft communities is not merely a matter of gaining a professional degree; instead, it is a slow process of enculturation.Keywords: Observation, Emulation, Inexplicit learning, Master-apprentice. Communities of Practice

Desenvolvimento e estudos de estabilidade preliminares de emulsões O/A contendo Cetoconazol 2,0% - DOI: 10.4025/actascihealthsci.v30i2.812 Development and Preliminary Stability Evaluations of O/W emulsion containing Ketoconazole 2.0% - DOI: 10.4025/actascihealthsci.v30i2.812

Directory of Open Access Journals (Sweden)

Márcio Augusto Leite de Campos

2008-12-01

Full Text Available O objetivo deste trabalho foi desenvolver emulsões O/A contendo Cetoconazol 2,0% e avaliar sua estabilidade preliminar por meio da análise de suas características físico-químicas, tais como homogeneidade, formação de agregados, floculação, cremeação e coalescência. As emulsões foram formuladas utilizando diferentes bases autoemulsionantes, compostas por álcool cetoestearílico, álcool etoxilado, álcool graxos superiores, ácido esteárico, lanolina e outros. As emulsões foram submetidas aos testes de centrifugação, estresse térmico e ciclo gela-degela, e suas características organolépticas e físico-químicas foram avaliadas no início e no final de cada ensaio. Todas as amostras mantiveram sua homogeneidade após o teste de centrifugação, mas somente os sistemas preparados com ceras autoemulsionáveis constituídas por álcool graxos superiores (Polawax NF® e Copolímero de Amônio Acriloil dimetiltaurato VP, Trilauril 4 fosfato, Sesquisosterato de metil glicose, Óleo de flores de verão e Tetradibutil pentaeritritil hidroxihidrocinamato de Glicerina (Hostacerin NCB® ; mantiveram sua estabilidade após testes de estresse térmico e ciclo gela-degelaThe objective of this work was the development of O/W emulsions containing Ketoconazole 2.0% and to evaluate their preliminary stability by analyzing physical-chemical characteristics such as homogeneity, aggregation formation, flocculation, creaming and coalescence. The emulsions were formulated using different self-emulsifying bases, composed of cetearyl alcohol, ethoxyl alcohol, higher fatty alcohol, stearic acid, lanolin and others. The O/W emulsions were evaluated by centrifugation test, thermal stress test, and freezing/defrosting cycles, and its organoleptic and physical-chemistry characteristics were analyzed before and after each assay. All samples maintained their homogeneity after the centrifugation test, but only the systems prepared with self emulsifying

Emulation of simulations of atmospheric dispersion at Fukushima for Sobol' sensitivity analysis

Science.gov (United States)

Girard, Sylvain; Korsakissok, Irène; Mallet, Vivien

2015-04-01

Polyphemus/Polair3D, from which derives IRSN's operational model ldX, was used to simulate the atmospheric dispersion at the Japan scale of radionuclides after the Fukushima disaster. A previous study with the screening method of Morris had shown that - The sensitivities depend a lot on the considered output; - Only a few of the inputs are non-influential on all considered outputs; - Most influential inputs have either non-linear effects or are interacting. These preliminary results called for a more detailed sensitivity analysis, especially regarding the characterization of interactions. The method of Sobol' allows for a precise evaluation of interactions but requires large simulation samples. Gaussian process emulators for each considered outputs were built in order to relieve this computational burden. Globally aggregated outputs proved to be easy to emulate with high accuracy, and associated Sobol' indices are in broad agreement with previous results obtained with the Morris method. More localized outputs, such as temporal averages of gamma dose rates at measurement stations, resulted in lesser emulator performances: tests simulations could not satisfactorily be reproduced by some emulators. These outputs are of special interest because they can be compared to available observations, for instance for calibration purpose. A thorough inspection of prediction residuals hinted that the model response to wind perturbations often behaved in very distinct regimes relatively to some thresholds. Complementing the initial sample with wind perturbations set to the extreme values allowed for sensible improvement of some of the emulators while other remained too unreliable to be used in a sensitivity analysis. Adaptive sampling or regime-wise emulation could be tried to circumvent this issue. Sobol' indices for local outputs revealed interesting patterns, mostly dominated by the winds, with very high interactions. The emulators will be useful for subsequent studies. Indeed

Fast emulation of track reconstruction in the CMS simulation

CERN Document Server

Komm, Matthias

2017-01-01

Simulated samples of various physics processes are a key ingredient within analyses to unlock the physics behind LHC collision data. Samples with more and more statistics are required to keep up with the increasing amounts of recorded data. During sample generation, significant computing time is spent on the reconstruction of charged particle tracks from energy deposits which additionally scales with the pileup conditions. In CMS, the FastSimulation package is developed for providing a fast alternative to the standard simulation and reconstruction workflow. It employs various techniques to emulate track reconstruction effects in particle collision events. Several analysis groups in CMS are utilizing the package, in particular those requiring many samples to scan the parameter space of physics models (e.g. SUSY) or for the purpose of estimating systematic uncertainties. The strategies for and recent developments in this emulation are presented, including a novel, flexible implementation of tracking emulation w...

The Ghost Condition: Imitation Versus Emulation in Young Children's Observational Learning.

Science.gov (United States)

Thompson, Doreen E.; Russell, James

2004-01-01

Although observational learning by children may occur through imitating a modeler's actions, it can also occur through learning about an object's dynamic affordances- a process that M. Tomasello (1996) calls "emulation." The relative contributions of imitation and emulation within observational learning were examined in a study with 14- to…

Evaluation of emulsifier stability of biosurfactant produced by Saccharomyces lipolytica CCT-0913

OpenAIRE

Lima,Álvaro Silva; Alegre,Ranulfo Monte

2009-01-01

Surface-active compounds of biological origin are widely used for many industries (cosmetic, food, petrochemical). The Saccharomyces lipolytica CCT-0913 was able to grow and produce a biosurfactant on 5% (v/v) diesel-oil at pH 5.0 and 32ºC. The cell-free broth emulsified and stabilized the oil-in-water emulsion through a first order kinetics. The results showed that the initial pH value and temperature influenced the emulsifier stability (ES), which was the time when oil was separated. The bi...

W-NINE: A Two-Stage Emulation Platform for Mobile and Wireless Systems

Directory of Open Access Journals (Sweden)

Emmanuel Conchon

2010-01-01

Full Text Available More and more applications and protocols are now running on wireless networks. Testing the implementation of such applications and protocols is a real challenge as the position of the mobile terminals and environmental effects strongly affect the overall performance. Network emulation is often perceived as a good trade-off between experiments on operational wireless networks and discrete-event simulations on Opnet or ns-2. However, ensuring repeatability and realism in network emulation while taking into account mobility in a wireless environment is very difficult. This paper proposes a network emulation platform, called W-NINE, based on off-line computations preceding online pattern-based traffic shaping. The underlying concepts of repeatability, dynamicity, accuracy, and realism are defined in the emulation context. Two different simple case studies illustrate the validity of our approach with respect to these concepts.

Effects of inulin on the structure and emulsifying properties of protein components in dough.

Science.gov (United States)

Liu, Juan; Luo, Denglin; Li, Xuan; Xu, Baocheng; Zhang, Xiaoyu; Liu, Jianxue

2016-11-01

High-purity gliadin, glutenin and gluten fractions were extracted from wheat gluten flour. To investigate the effects of three types of inulin with different degrees of polymerization (DP) on the emulsifying properties, disulfide contents, secondary structures and microstructures of these fractions, Turbidimetry, spectrophotometer, Fourier transform infrared spectroscopy (FT-IR) and scanning electron microscopy (SEM) were used in this study. The results showed that the emulsifying activity of gliadin was higher than that of glutenin and gluten, but its emulsion stability was lower than that of glutenin. Adding inulin increased the emulsifying activity of the three protein fractions and emulsion stability of gliadin and gluten, but decreased the emulsion stability of glutenin and disulfide bond contents of glutenin and gluten. In the presence of inulin, the α-helical structure of the three proteins had no significant change, whereas the β-turn structure decreased and β-sheet structure increased. The SEM images showed that inulin had the most significant effect on the glutenin microstructure. In general, inulin with a higher DP had greater effects on the structure and emulsifying properties of protein components in dough. Copyright © 2016 Elsevier Ltd. All rights reserved.

Emulating Science

Directory of Open Access Journals (Sweden)

Carneiro, Larissa

2017-11-01

Full Text Available This article compares forms of visual argumentation in the scientific study of evolution and Young-Earth Creationism, arguing that secular forms of scientific representation have affected the way creationists visually construct their own. In order to affirm their view of the origin of the universe, creationists borrow from, mimic, and ultimately emulate the techniques, or at least the appearance, of scientific method and reasoning. The use of the word “emulation” is very deliberate since their aim is to match and surpass a rival scientific paradigm – evolution. The sermon preached by the design of the Creation Museum in Petersburg, Kentucky, is not content simply to look like science, but aims to do science that is affirmed by the Scriptures.

Antioxidant Properties of Astaxanthin in Oil-in-Water Emulsions with Differently-Charged Emulsifiers Under Chlorophyll Photosensitization.

Science.gov (United States)

Yi, BoRa; Kim, Mi-Ja; Lee, JaeHwan

2018-03-01

The antioxidative or prooxidative properties of astaxanthin at the concentrations of 0, 10, and 100 μM were determined in oil-in-water (O/W) emulsions containing neutral, anionic, and cationic emulsifiers, which was Tween 20, sodium dodecyl sulfate, cetyltrimethylammonium bromide (CTAB), respectively, under chlorophyll photosensitization. The oxidative parameters and headspace volatiles were analyzed in O/W emulsions. In the 24 h period of visible light irradiation, 100 μM of astaxanthin acted as an antioxidant in O/W emulsions containing neutral and anionic emulsifiers. However, astaxanthin in O/W emulsions with a cationic emulsifier was neither an antioxidant nor a prooxidant. The profiles of volatile compounds showed that astaxanthin served as a singlet oxygen quencher in O/W emulsions containing neutral and anionic emulsifiers. However, in O/W emulsion with a cationic emulsifier, astaxanthin was neither a singlet oxygen quencher nor a free radical scavenger because prooxidant properties of CTAB overwhelmed the antioxidant effects of astaxanthin. Therefore, the antioxidant properties of astaxanthin were influenced by the emulsifier charges in O/W emulsions. Astaxanthin is a lipid-soluble pigment and has antioxidant, anticancer, and anti-inflammatory properties and beneficial effects on cardiovascular diseases. Many lipid-based foods are displayed on the shelves in the markets under fluorescent light. The addition of astaxanthin can extend the shelf life of O/W emulsion type foods such as beverage and dressing products under visible light irradiation. Also, oxidative stability in emulsion type foods containing astaxanthin rich natural ingredients can be predicted. © 2018 Institute of Food Technologists®.

Biopharmaceutical insights of particulate emulsified systems - a prospective overview.

Science.gov (United States)

Katamreddy, Jyothshna Devi; Yalavarthi, Prasanna Raju; D, Subba Rao; Battu, Sowjanya; Peesa, Jaya Preethi

2018-05-10

During the twenty-first century, drug discovery is expanding rapidly and a large number of chemical moieties are recognized. Many of them are poorly soluble and hence related biopharmaceutical constraints are to be addressed systematically. Among novel approaches to resolving biopharmaceutical issues, micro- and nano-emulsified systems serve as the best strategy for delivering both hydrophobic and hydrophilic drugs owing to their greater solubilization and transportation capabilities. Of late, the unique physical and biopharmaceutical properties of these liquid isotropic homogenous systems have gained substantive research importance. In addition nano/micro lipid systems share structural and functional similarity with that of the physiological lipids which offer better tolerance ability in the body. In this context, this article provides information on the historical emergence of particulate emulsified systems, importance and rationale of selection of carriers. It also encompasses the physicochemical principles that are responsible for the elevation of therapeutic outcomes of delivery systems. Detailed and schematic absorption of these drug delivery systems is explained here. Gastro-intestinal biochemistry necessary in the understanding of digestion process, lipolytic products formed, micellar structures, enzymes, transporters, mechanism of cell uptake involved after subsequent oral absorption are also emphasized. In addition, this article also explains disposition and pharmacokinetic properties of emulsified systems with real-time therapeutic research outcomes. The influence of biochemical compositions and biopharmaceutical principles on absorption and disposition patterns of ME/NEs was described in the article for the interest of readers and young researchers.

Surface Enrichment by Conventional and Polymerizable Sulfated Nonylphenol Ethoxylate Emulsifiers in Water-Based Pressure-Sensitive Adhesive

Science.gov (United States)

Jilin Zhang; Yuxi Zhao; Matthew R. Dubay; Steven J. Severtson; Larry E. Gwin; Carl J. Houtman

2013-01-01

Comparisons of properties are made for pressure-sensitive adhesives (PSAs) generated via emulsion polymerization using both conventional and reactive emulsifiers. The emulsifiers are ammonium salts of sulfated nonylphenol ethoxylates with similar chemical structures and hydrophilic−lipophilic balances. The polymerizable surfactant possesses a reactive double...

The Preparation and Performances of Self-Dispersed Nanomicron Emulsified Wax Solid Lubricant Ewax for Drilling Fluids

Directory of Open Access Journals (Sweden)

Feng-shan Zhou

2014-01-01

Full Text Available An oil-in-water nanomicron wax emulsion with oil phase content 45 wt% was prepared by using the emulsifying method of surfactant-in-oil. The optimum prepared condition is 85°C, 20 min, and 5 wt% complex emulsifiers. Then the abovementioned nanomicron emulsifying wax was immersed into a special water-soluble polymer in a certain percentage by the semidry technology. At last, a solidified self-dispersed nanomicron emulsified wax named as Ewax, a kind of solid lubricant for water based drilling fluid, was obtained after dried in the special soluble polymer containing emulsifying wax in low temperature. It is shown that the adhesion coefficient reduced rate (ΔKf is 73.5% and the extreme pressure (E-P friction coefficient reduced rate (Δf is 77.6% when the produced Ewax sample was added to fresh water based drilling fluid at dosage 1.0 wt%. In comparison with other normal similar liquid products, Ewax not only has better performances of lubrication, filtration loss control property, heat resistance, and tolerance to salt and is environmentally friendly, but also can solve the problems of freezing in the winter and poor storage stability of liquid wax emulsion in oilfield applications.

Developing a real-time emulation of multiresolutional control architectures for complex, discrete-event systems

Energy Technology Data Exchange (ETDEWEB)

Davis, W.J.; Macro, J.G.; Brook, A.L. [Univ. of Illinois, Urbana, IL (United States)] [and others

1996-12-31

This paper first discusses an object-oriented, control architecture and then applies the architecture to produce a real-time software emulator for the Rapid Acquisition of Manufactured Parts (RAMP) flexible manufacturing system (FMS). In specifying the control architecture, the coordinated object is first defined as the primary modeling element. These coordinated objects are then integrated into a Recursive, Object-Oriented Coordination Hierarchy. A new simulation methodology, the Hierarchical Object-Oriented Programmable Logic Simulator, is then employed to model the interactions among the coordinated objects. The final step in implementing the emulator is to distribute the models of the coordinated objects over a network of computers and to synchronize their operation to a real-time clock. The paper then introduces the Hierarchical Subsystem Controller as an intelligent controller for the coordinated object. The proposed approach to intelligent control is then compared to the concept of multiresolutional semiosis that has been developed by Dr. Alex Meystel. Finally, the plans for implementing an intelligent controller for the RAMP FMS are discussed.

Yielding physically-interpretable emulators - A Sparse PCA approach

Science.gov (United States)

Galelli, S.; Alsahaf, A.; Giuliani, M.; Castelletti, A.

2015-12-01

Projection-based techniques, such as Principal Orthogonal Decomposition (POD), are a common approach to surrogate high-fidelity process-based models by lower order dynamic emulators. With POD, the dimensionality reduction is achieved by using observations, or 'snapshots' - generated with the high-fidelity model -, to project the entire set of input and state variables of this model onto a smaller set of basis functions that account for most of the variability in the data. While reduction efficiency and variance control of POD techniques are usually very high, the resulting emulators are structurally highly complex and can hardly be given a physically meaningful interpretation as each basis is a projection of the entire set of inputs and states. In this work, we propose a novel approach based on Sparse Principal Component Analysis (SPCA) that combines the several assets of POD methods with the potential for ex-post interpretation of the emulator structure. SPCA reduces the number of non-zero coefficients in the basis functions by identifying a sparse matrix of coefficients. While the resulting set of basis functions may retain less variance of the snapshots, the presence of a few non-zero coefficients assists in the interpretation of the underlying physical processes. The SPCA approach is tested on the reduction of a 1D hydro-ecological model (DYRESM-CAEDYM) used to describe the main ecological and hydrodynamic processes in Tono Dam, Japan. An experimental comparison against a standard POD approach shows that SPCA achieves the same accuracy in emulating a given output variable - for the same level of dimensionality reduction - while yielding better insights of the main process dynamics.

Emulation tool of dynamic systems via internet

Directory of Open Access Journals (Sweden)

Daniel Ruiz Olaya

2015-11-01

Full Text Available The experimentation laboratories for the studies of control system courses can become expensive, either in its acquisition, operation or maintenance. An alternative resource have been the remote laboratories. However, not always is possible to get complex systems. A solution to this matter are the remote emulation laboratories. In this paper describes the development of a Web application for the emulation of dynamic systems using a free-distribution software tool of rapid control prototyping based on Linux/RTAI. This application is focused especially for the experimentation with dynamic systems that are not available easily in a laboratory where the model have been configured by the user. The design of the front-end and the back-end are presented. The latency times of the real-time operating system and the ability of the system to reproduce similar signals to a real system from an emulated model were verified. An example, to test the functionality of the application the model of an evaporator was used. One of the advantages of the application is the work methodology which is based on the development of blocks in Scicos. This allows the user to reuse those parameters and the code that was implemented to build a block on the Scicos toolbox with the Linux/RTAI/ScicosLab environment. Moreover, only a web-browser and the Java Virtual Machine are required.

High-emulation mask recognition with high-resolution hyperspectral video capture system

Science.gov (United States)

Feng, Jiao; Fang, Xiaojing; Li, Shoufeng; Wang, Yongjin

2014-11-01

We present a method for distinguishing human face from high-emulation mask, which is increasingly used by criminals for activities such as stealing card numbers and passwords on ATM. Traditional facial recognition technique is difficult to detect such camouflaged criminals. In this paper, we use the high-resolution hyperspectral video capture system to detect high-emulation mask. A RGB camera is used for traditional facial recognition. A prism and a gray scale camera are used to capture spectral information of the observed face. Experiments show that mask made of silica gel has different spectral reflectance compared with the human skin. As multispectral image offers additional spectral information about physical characteristics, high-emulation mask can be easily recognized.

Emulsifiers' composition modulates venous irritation of the nanoemulsions as a lipophilic and venous irritant drug delivery system.

Science.gov (United States)

Mao, Chengwen; Wan, Jiangling; Chen, Huabing; Xu, Huibi; Yang, Xiangliang

2009-01-01

In this study, a nanoemulsion (NE) system was investigated for intravenous delivery of lipophilic and venous irritant drugs. NEs were prepared to deliver diallyl trisulfide (DT) for systemic therapy of bacterial and fungal infection, egg phospholipid was chosen as the main emulsifier, and two co-emulsifiers were also incorporated, including Poloxamer 188 (P188) and Solutol HS 15 (S15). Soybean oil was used as the dispersed phases, forming stable DT NEs with small particle sizes. The venous irritation of DT NEs was evaluated by in vitro human umbilical cord endothelial cells (CRL 1730) compatibility model with the intracellular adenosine triphosphate (ATP) and guanosine triphosphate (GTP) concentrations as the indices. The intracellular ATP and GTP reduction changed with the incorporation of a variety of co-emulsifiers, which varied in a free DT concentration-dependent manner. It was deduced that the free DT concentrations of NEs containing co-emulsifiers were determined by the partition coefficient of DT between oil and surfactant buffer solution. In conclusion, NE was an appropriate delivery system for lipophilic and venous irritant drug, and optimization of the composition of emulsifiers was an effective method to alleviate the venous irritation of DT NEs.

Potential of L-fucose isolated from Brown Seaweeds as Promising Natural Emulsifier compare to Carboxymethyl Cellulose (CMC)

Science.gov (United States)

Al-Baarri, A. N.; Legowo, A. M.; Widayat; Abduh, S. B. M.; Lestari, F. P.; Desnasari, D.; Santoso, I. P. M.

2018-02-01

L-fucose has been understood as sulfated polysaccharides and it could be extracted and fractionated from brown algae. These polysaccharides contains carbohydrate, sulfate, and protein that may be used as emulsifier. This research was aimed to study the emulsification properties of L-fucose through the determination of total dissolved solids (TDS), color CIE L*a*b* and stability of oil-in-water emulsion. As much as 0.5% of high concentrated L-fucose and 0.5% of carboxymethyl cellulose (CMC) were used as emulsifier in a 10% (v/v) oil-in-water (O/W) emulsion. The emulsifier was added to O/W emulsions and then heated at 72°C. Result of stability emulsion and TDS showed that L-fucose was comparable to the CMC but remarkable changed the color of O/W emulsion. Heating process significantly reduced the stability O/W emulsion when L-fucose was applied. As conclusion, L-fucose might be used as natural emulsifier in O/W emulsion but in the low heat treatment of food processing. This study may provide valuable information for utilizing natural emulsifier from abundant resources from nature.

Synthesis and characterization of nano-SiO{sub 2} modified fluorine-containing polyacrylate emulsifier-free emulsion

Energy Technology Data Exchange (ETDEWEB)

Zhou, Jianhua, E-mail: zhoujianh@21cn.com [College of Resource and Environment, Shaanxi University of Science and Technology, Xi’an 710021 (China); Shaanxi Research Institute of Agricultural Products Processing Technology, Xi’an 710021 (China); Chen, Xin; Duan, Hao; Ma, Jianzhong; Ma, Yurong [College of Resource and Environment, Shaanxi University of Science and Technology, Xi’an 710021 (China)

2015-03-15

Graphical abstract: Nano-SiO{sub 2} modified fluorine-containing polyacrylate emulsifier-free emulsion was synthesized by emulsifier-free emulsion polymerization and sol–gel process using ethyl silicate as precursor for nano-SiO{sub 2}. - Highlights: • Nano-SiO{sub 2} modified fluorine-containing polyacrylate emulsifier-free emulsion was successfully synthesized by emulsion polymerization using surfmer and sol–gel process. • The contact angle results showed that the finished fabric had an excellent water and oil repellency. • The nano-SiO{sub 2} modified fluorine-containing polyacrylate emulsifier-free emulsion proved to be highly solvent-resistant and water-resistant. • The transmission electron microscopy (TEM) indicated that the nano-SiO{sub 2} presented on the surface of latex particles. • The atomic force microscope (AFM) and energy dispersive X-ray spectrometer (EDX) confirmed that the hybrid film had a rough surface and the organic fluorine segment could migrate onto the film–air interface. - Abstract: Nano-SiO{sub 2} modified fluorine-containing polyacrylate emulsifier-free emulsion, consisting of methyl methacrylate, butyl acrylate, dodecafluoroheptyl methacrylate and ethyl silicate, was successfully synthesized by emulsion polymerization using surfmer and sol–gel process. When increasing ethyl silicate content, the latex centrifugal stability decreased, and the latex particle size increased. The contact angle results showed that the finished fabric had an excellent water and oil repellency. Furthermore, compared with fluorine-containing polyacrylate emulsifier-free emulsion, the obtained nano-SiO{sub 2} modified fluorine-containing polyacrylate emulsifier-free emulsion proved to be highly solvent-resistant and water-resistant. In addition, the transmission electron microscopy (TEM) indicated that the nano-SiO{sub 2} presented on the surface of latex particles. The atomic force microscope (AFM) and energy dispersive X-ray spectrometer

Produced water treatment for beneficial use : emulsified oil removal

NARCIS (Netherlands)

Waisi, Basma

2016-01-01

The development of novel carbon material, high accessible surface area, interconnected porosity, and stable nanofiber nonwoven media for emulsified oil droplets separation from oily wastewater, in particular for oilfields produced water treatment, is discussed in this thesis. Firstly, the quantity

Internal monitoring of GBTx emulator using IPbus for CBM experiment

Science.gov (United States)

Mandal, Swagata; Zabolotny, Wojciech; Sau, Suman; Chkrabarti, Amlan; Saini, Jogender; Chattopadhyay, Subhasis; Pal, Sushanta Kumar

2015-09-01

The Compressed Baryonic Matter (CBM) experiment is a part of the Facility for Antiproton and Ion Research (FAIR) in Darmstadt at GSI. In CBM experiment a precisely time synchronized fault tolerant self-triggered electronics is required for Data Acquisition (DAQ) system in CBM experiments which can support high data rate (up to several TB/s). As a part of the implementation of the DAQ system of Muon Chamber (MUCH) which is one of the important detectors in CBM experiment, a FPGA based Gigabit Transceiver (GBTx) emulator is implemented. Readout chain for MUCH consists of XYTER chips (Front end electronics) which will be directly connected to detector, GBTx emulator, Data Processing Board (DPB) and First level event selector board (FLIB) with backend software interface. GBTx emulator will be connected with the XYTER emulator through LVDS (Low Voltage Differential Signalling) line in the front end and in the back end it is connected with DPB through 4.8 Gbps optical link. IPBus over Ethernet is used for internal monitoring of the registers within the GBTx. In IPbus implementation User Datagram Protocol (UDP) stack is used in transport layer of OSI model so that GBTx can be controlled remotely. A Python script is used at computer side to drive IPbus controller.

Thermoelectric Generator Emulator for MPPT Testing

DEFF Research Database (Denmark)

Man, Elena Anamaria; Sera, Dezso; Máthé, Lászlo

2015-01-01

This paper presents a novel approach to use a DC power supply as a thermoelectric generator (TEG) emulator to perform static and dynamic maximum power point tracking (MPPT). First, the electrical characterization of a calcium-manganese-oxide module is performed on a TEG test rig. Afterwards...

Implementation of a MIX Emulator: A Case Study of the Scala Programming Language Facilities

Directory of Open Access Journals (Sweden)

Batdalov Ruslan

2017-12-01

Full Text Available Implementation of an emulator of MIX, a mythical computer invented by Donald Knuth, is used as a case study of the features of the Scala programming language. The developed emulator provides rich opportunities for program debugging, such as tracking intermediate steps of program execution, an opportunity to run a program in the binary or the decimal mode of MIX, verification of correct synchronisation of input/output operations. Such Scala features as cross-compilation, family polymorphism and support for immutable data structures have proved to be useful for implementation of the emulator. The authors of the paper also propose some improvements to these features: flexible definition of family-polymorphic types, integration of family polymorphism with generics, establishing full equivalence between mutating operations on mutable data types and copy-and-modify operations on immutable data types. The emulator is free and open source software available at www.mix-emulator.org.

Emulation-Based Virtual Laboratories: A Low-Cost Alternative to Physical Experiments in Control Engineering Education

Science.gov (United States)

Goodwin, G. C.; Medioli, A. M.; Sher, W.; Vlacic, L. B.; Welsh, J. S.

2011-01-01

This paper argues the case for emulation-based virtual laboratories in control engineering education. It demonstrates that such emulation experiments can give students an industrially relevant educational experience at relatively low cost. The paper also describes a particular emulation-based system that has been developed with the aim of giving…

Modeling for Ship Power System Emulation

Science.gov (United States)

2009-05-08

used repeatedly for load- identification in shipboard environments (3). The NILM may be able to improve the HSR performance by identifying...electric plant. One of the major reasons for the hardware emulator is to test the NILM in a ring distribution lineup to evaluate if power to particular

Statistical emulation of a tsunami model for sensitivity analysis and uncertainty quantification

Directory of Open Access Journals (Sweden)

A. Sarri

2012-06-01

Full Text Available Due to the catastrophic consequences of tsunamis, early warnings need to be issued quickly in order to mitigate the hazard. Additionally, there is a need to represent the uncertainty in the predictions of tsunami characteristics corresponding to the uncertain trigger features (e.g. either position, shape and speed of a landslide, or sea floor deformation associated with an earthquake. Unfortunately, computer models are expensive to run. This leads to significant delays in predictions and makes the uncertainty quantification impractical. Statistical emulators run almost instantaneously and may represent well the outputs of the computer model. In this paper, we use the outer product emulator to build a fast statistical surrogate of a landslide-generated tsunami computer model. This Bayesian framework enables us to build the emulator by combining prior knowledge of the computer model properties with a few carefully chosen model evaluations. The good performance of the emulator is validated using the leave-one-out method.

Dynamic emulation modelling for the optimal operation of water systems: an overview

Science.gov (United States)

Castelletti, A.; Galelli, S.; Giuliani, M.

2014-12-01

Despite sustained increase in computing power over recent decades, computational limitations remain a major barrier to the effective and systematic use of large-scale, process-based simulation models in rational environmental decision-making. Whereas complex models may provide clear advantages when the goal of the modelling exercise is to enhance our understanding of the natural processes, they introduce problems of model identifiability caused by over-parameterization and suffer from high computational burden when used in management and planning problems. As a result, increasing attention is now being devoted to emulation modelling (or model reduction) as a way of overcoming these limitations. An emulation model, or emulator, is a low-order approximation of the process-based model that can be substituted for it in order to solve high resource-demanding problems. In this talk, an overview of emulation modelling within the context of the optimal operation of water systems will be provided. Particular emphasis will be given to Dynamic Emulation Modelling (DEMo), a special type of model complexity reduction in which the dynamic nature of the original process-based model is preserved, with consequent advantages in a wide range of problems, particularly feedback control problems. This will be contrasted with traditional non-dynamic emulators (e.g. response surface and surrogate models) that have been studied extensively in recent years and are mainly used for planning purposes. A number of real world numerical experiences will be used to support the discussion ranging from multi-outlet water quality control in water reservoir through erosion/sedimentation rebalancing in the operation of run-off-river power plants to salinity control in lake and reservoirs.

[Treatment of wrinkles of the upper lip by emulsified fat or "Nanofat": Biological and clinical study about 4 cases].

Science.gov (United States)

Mesguich Batel, F; Bertrand, B; Magalon, J; François, P; Velier, M; Veran, J; Mallet, S; Jouve, E; Sabatier, F; Casanova, D

2018-02-01

Emulsified fat injection showed its interest in aesthetic facial surgery. The adipose tissue harvested is mechanically emulsified and filtered. The suspension obtained is injected into the dermis through small diameter needles (27 to 30 gauges). The objective of our study was to evaluate the biological composition of emulsified fat and its clinical effectiveness in the treatment of peri-oral wrinkles in 4 patients aged 50 to 59 years. Each patient received an intradermal injection of emulsified fat in the peri-oral wrinkles prepared from abdominal fat under local anesthesia. The cell viability, stromal vascular fraction (FVS) composition in emulsified fat and the adipocyte differentiation capacity of mesenchymal stem cells (MSC) were studied. The clinical results were evaluated by standardized photographs, 3D microphotography, confocal microscopy, and self-evaluation of patient satisfaction over a period of 4 months. The biological study of the emulsified fat found a lysis of all the adipocytes. The mean number of FVS cells was 126,330±2758 cells by cc of emulsified fat with preserved cell viability (85.1±6.84 %) and a good proportion of regeneratives cells (18.77±6.2 %). The clinical study found a tendency to decrease the volume of wrinkles on standardized photography and 3D microphotography no significative. Patients were satisfied with treatment with an average score of 7±1.15/10 to 4 months. Intradermal injection of emulsified fat seems to be an interesting treatment of face wrinkles. Our study has shown its safety, but additional studies seems necessary to confirm its clinical efficacy. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

Multislice computed tomography: angiographic emulation versus standard assessment for detection of coronary stenoses

Energy Technology Data Exchange (ETDEWEB)

Schnapauff, Dirk; Hamm, Bernd; Dewey, Marc [Humboldt-Universitaet zu Berlin, Department of Radiology, Charite - Universitaetsmedizin Berlin, Chariteplatz 1, P.O. Box 10098, Berlin (Germany); Duebel, Hans-Peter; Baumann, Gert [Charite - Universitaetsmedizin Berlin, Department of Cardiology, Berlin (Germany); Scholze, Juergen [Charite - Universitaetsmedizin Berlin, Charite Outpatient Centre, Berlin (Germany)

2007-07-15

The present study investigated angiographic emulation of multislice computed tomography (MSCT) (catheter-like visualization) as an alternative approach of analyzing and visualizing findings in comparison with standard assessment. Thirty patients (120 coronary arteries) were randomly selected from 90 prospectively investigated patients with suspected coronary artery disease who underwent MSCT (16-slice scanner, 0.5 mm collimation, 400 ms rotation time) prior to conventional coronary angiography for comparison of both approaches. Sensitivity and specificity of angiographic emulation [81% (26/32) and 93% (82/88)] were not significantly different from those of standard assessment [88% (28/32) and 99% (87/88)], while the per-case analysis time was significantly shorter for angiographic emulation than for standard assessment (3.4 {+-} 1.5 vs 7.0 {+-} 2.5 min, P < 0.001). Both interventional and referring cardiologists preferred angiographic emulation over standard curved multiplanar reformations of MSCT coronary angiography for illustration, mainly because of improved overall lucidity and depiction of sidebranches (P < 0.001). In conclusion, angiographic emulation of MSCT reduces analysis time, yields a diagnostic accuracy comparable to that of standard assessment, and is preferred by cardiologists for visualization of results. (orig.)

A physics informed emulator for laser-driven radiating shock simulations

KAUST Repository

McClarren, Ryan G.; Ryu, D.; Paul Drake, R.; Grosskopf, Michael; Bingham, Derek; Chou, Chuan-Chih; Fryxell, Bruce; van der Holst, Bart; Paul Holloway, James; Kuranz, Carolyn C.; Mallick, Bani; Rutter, Erica; Torralva, Ben R.

2011-01-01

This work discusses the uncertainty quantification aspect of quantification of margin and uncertainty (QMU) in the context of two linked computer codes. Specifically, we present a physics based reduction technique to deal with functional data from the first code and then develop an emulator for this reduced data. Our particular application deals with conditions created by laser deposition in a radiating shock experiment modeled using the Lagrangian, radiation-hydrodynamics code Hyades. Our goal is to construct an emulator and perform a sensitivity analysis of the functional output from Hyades to be used as an initial condition for a three-dimensional code that will compute the evolution of the radiating shock at later times. Initial attempts at purely statistical data reduction techniques, were not successful at reducing the number of parameters required to describe the Hyades output. We decided on an alternate approach using physical arguments to decide what features/locations of the output were relevant (e.g., the location of the shock front or the location of the maximum pressure) and then used a piecewise linear fit between these locations. This reduced the number of outputs needed from the emulator to 40, down from the O(1000) points in the Hyades output. Then, using Bayesian MARS and Gaussian process regression, we were able to build emulators for Hyades and study sensitivities to input parameters. © 2011 Elsevier Ltd. All rights reserved.

A physics informed emulator for laser-driven radiating shock simulations

KAUST Repository

McClarren, Ryan G.

2011-09-01

This work discusses the uncertainty quantification aspect of quantification of margin and uncertainty (QMU) in the context of two linked computer codes. Specifically, we present a physics based reduction technique to deal with functional data from the first code and then develop an emulator for this reduced data. Our particular application deals with conditions created by laser deposition in a radiating shock experiment modeled using the Lagrangian, radiation-hydrodynamics code Hyades. Our goal is to construct an emulator and perform a sensitivity analysis of the functional output from Hyades to be used as an initial condition for a three-dimensional code that will compute the evolution of the radiating shock at later times. Initial attempts at purely statistical data reduction techniques, were not successful at reducing the number of parameters required to describe the Hyades output. We decided on an alternate approach using physical arguments to decide what features/locations of the output were relevant (e.g., the location of the shock front or the location of the maximum pressure) and then used a piecewise linear fit between these locations. This reduced the number of outputs needed from the emulator to 40, down from the O(1000) points in the Hyades output. Then, using Bayesian MARS and Gaussian process regression, we were able to build emulators for Hyades and study sensitivities to input parameters. © 2011 Elsevier Ltd. All rights reserved.

Statistical emulation of landslide-induced tsunamis at the Rockall Bank, NE Atlantic.

Science.gov (United States)

Salmanidou, D M; Guillas, S; Georgiopoulou, A; Dias, F

2017-04-01

Statistical methods constitute a useful approach to understand and quantify the uncertainty that governs complex tsunami mechanisms. Numerical experiments may often have a high computational cost. This forms a limiting factor for performing uncertainty and sensitivity analyses, where numerous simulations are required. Statistical emulators, as surrogates of these simulators, can provide predictions of the physical process in a much faster and computationally inexpensive way. They can form a prominent solution to explore thousands of scenarios that would be otherwise numerically expensive and difficult to achieve. In this work, we build a statistical emulator of the deterministic codes used to simulate submarine sliding and tsunami generation at the Rockall Bank, NE Atlantic Ocean, in two stages. First we calibrate, against observations of the landslide deposits, the parameters used in the landslide simulations. This calibration is performed under a Bayesian framework using Gaussian Process (GP) emulators to approximate the landslide model, and the discrepancy function between model and observations. Distributions of the calibrated input parameters are obtained as a result of the calibration. In a second step, a GP emulator is built to mimic the coupled landslide-tsunami numerical process. The emulator propagates the uncertainties in the distributions of the calibrated input parameters inferred from the first step to the outputs. As a result, a quantification of the uncertainty of the maximum free surface elevation at specified locations is obtained.

Burning Rate Emulator Experiments for Spacecraft Fire Safety

Data.gov (United States)

National Aeronautics and Space Administration — Experimental Investigation of Emulated Burning Rate at Various Gravity Levels Support for the initial development stages of a novel experimental apparatus, the...

Competitive displacement of sodium caseinate by low-molecular-weight emulsifiers and the effects on emulsion texture and rheology.

Science.gov (United States)

Munk, M B; Larsen, F H; van den Berg, F W J; Knudsen, J C; Andersen, M L

2014-07-29

Low-molecular-weight (LMW) emulsifiers are used to promote controlled destabilization in many dairy-type emulsions in order to obtain stable foams in whippable products. The relation between fat globule aggregation induced by three LMW emulsifiers, lactic acid ester of monoglyceride (LACTEM), saturated monoglyceride (GMS), and unsaturated monoglyceride (GMU) and their effect on interfacial protein displacement was investigated. It was found that protein displacement by LMW emulsifiers was not necessary for fat globule aggregation in emulsions, and conversely fat globule aggregation was not necessarily accompanied by protein displacement. The three LMW emulsifiers had very different effects on emulsions. LACTEM induced shear instability of emulsions, which was accompanied by protein displacement. High stability was characteristic for emulsions with GMS where protein was displaced from the interface. Emulsions containing GMU were semisolid, but only low concentrations of protein were detected in the separated serum phase. The effects of LACTEM, GMS, and GMU may be explained by three different mechanisms involving formation of interfacial α-gel, pickering stabilization and increased exposure of bound casein to the water phase. The latter may facilitate partial coalescence. Stabilizing hydrocolloids did not have any effect on the LMW emulsifiers' ability to induce protein displacement.

Effect of emulsifiers on complexation and retrogradation characteristics of native and chemically modified White sorghum (Sorghum bicolor) starch

International Nuclear Information System (INIS)

Ali, Tahira Mohsin; Hasnain, Abid

2013-01-01

Highlights: ► Sorghum starches were chemically modified. ► Starch–lipid complexes were studied in the presence of emulsifiers. ► Type II complexes were also detected in native and oxidized starches on adding GMS. ► Starch–lipid complexes sharply reduced retrogradation in modified starches. - Abstract: The effect of emulsifiers on complexation and retrogradation characteristics of native and chemically modified white sorghum starches was studied. Complex forming tendency of white sorghum starch with commercially available emulsifiers GMS and DATEM improved after acetylation. Presence of emulsifiers reduced λ max (wavelength of maximum absorbance) both for native and modified sorghum starches suggesting lower availability of amylose chains to complex with iodine. In native white sorghum starch (NWSS) and oxidized white sorghum starch (OWSS), both Type I and Type II starch–lipid complexes were observed on addition of 1.0% GMS prior to gelatinization. Acetylated-oxidized white sorghum starch (AOWSS) formed weakest complexes among all the modified starches. The results revealed that antistaling characteristics of modified sorghum starches were enhanced when used in combination with emulsifiers. The most prominent decline in reassociative capability among modified starches was observed for acetylated starches.

Approach for energy saving and pollution reducing by fueling diesel engines with emulsified biosolution/ biodiesel/diesel blends.

Science.gov (United States)

Lin, Yuan-Chung; Lee, Wen-Jhy; Chao, How-Ran; Wang, Shu-Li; Tsou, Tsui-Chun; Chang-Chien, Guo-Ping; Tsai, Perng-Jy

2008-05-15

The developments of both biodiesel and emulsified diesel are being driven by the need for reducing emissions from diesel engines and saving energy. Artificial chemical additives are also being used in diesel engines for increasing their combustion efficiencies. But the effects associated with the use of emulsified additive/biodiesel/diesel blends in diesel engines have never been assessed. In this research, the premium diesel fuel (PDF) was used as the reference fuel. A soy-biodiesel was selected as the test biodiesel. A biosolution made of 96.5 wt % natural organic enzyme-7F (NOE-7F) and 3.5 wt % water (NOE-7F water) was used as the fuel additive. By adding additional 1 vol % of surfactant into the fuel blend, a nanotechnology was used to form emulsified biosolution/soy-biodiesel/PDF blends for fueling the diesel engine. We found that the emulsified biosolution/soy-biodiesel/PDF blends did not separate after being kept motionless for 30 days. The above stability suggests that the above combinations are suitable for diesel engines as alternative fuels. Particularly, we found that the emulsified biosolution/soy-biodiesel/PDF blends did have the advantage in saving energy and reducing the emissions of both particulate matters (PM) and polycyclic aromatic hydrocarbons (PAHs) from diesel engines as compared with PDF, soy-biodiesel/PDF blends, and emulsified soy-biodiesel/ PDF blends. The results obtained from this study will provide useful approaches for reducing the petroleum reliance, pollution, and global warming. However, it should be noted that NO(x) emissions were not measured in the present study which warrants the need for future investigation.

Cellular automata machines as physics emulators

International Nuclear Information System (INIS)

Toffoli, T.

1988-01-01

Can one design a computer optimized to be a physics emulator rather than a software interpreter? Cellular automata are discrete dynamical systems whose behavior is completely specified in terms of a local relation, much as is the case for a large class of continuous dynamical systems defined by partial differential equations. 31 refs, 3 figs

Performance Evaluation, Emulation, and Control of Cross-Flow Hydrokinetic Turbines

Science.gov (United States)

Cavagnaro, Robert J.

power, and electrical power output of a complete power take-off (PTO) system are utilized to determine the rotor hydrodynamic efficiency (maximum of 17%) and total system efficiency (maximum of 9%). A lab-based dynamometry method yields individual component and total PTO efficiencies, shown to have high variability and strong influence on total system efficiency. Dynamic efficiencies of PTO components can effect the overall efficiency of a turbine system, a result from field characterization. Thus, the ability to evaluate such components and their potential effects on turbine performance prior to field deployment is desirable. Before attempting control experiments with actual turbines, hardware-in-the-loop testing on controllable motor-generator sets or electromechanical emulation machines (EEMs) are explored to better understand power take-off response. The emulator control dynamic equations are presented, methods for scaling turbine parameters are developed and evaluated, and experimental results are presented from three EEMs programmed to emulate the same cross-flow turbine. Although hardware platforms and control implementations varied, results show that each EEM is successful in emulating the turbine model at different power levels, thus demonstrating the general feasibility of the approach. However, performance of motor control under torque command, current command, or speed command differed; torque methods required accurate characterization of the motors while speed methods utilized encoder feedback and more accurately tracked turbine dynamics. In a demonstration of an EEM for evaluating a hydrokinetic turbine implementation, a controller is used to track the maximum power-point of the turbine in response to turbulence. Utilizing realistic inflow conditions and control laws, the emulator dynamic speed response is shown to agree well at low frequencies with simulation but to deviate at high frequencies. The efficacy of an electromechanical emulator as an accurate

On Emulation-Based Network Intrusion Detection Systems

NARCIS (Netherlands)

Abbasi, Ali; Wetzel, Jos; Bokslag, Wouter; Zambon, Emmanuele; Etalle, Sandro

2014-01-01

Emulation-based network intrusion detection systems have been devised to detect the presence of shellcode in network traffic by trying to execute (portions of) the network packet payloads in an in- strumented environment and checking the execution traces for signs of shellcode activity.

On emulation-based network intrusion detection systems

NARCIS (Netherlands)

Abbasi, A.; Wetzels, J.; Bokslag, W.; Zambon, E.; Etalle, S.; Stavrou, A.; Bos, H.; Portokalidis, G.

2014-01-01

Emulation-based network intrusion detection systems have been devised to detect the presence of shellcode in network traffic by trying to execute (portions of) the network packet payloads in an instrumented environment and checking the execution traces for signs of shellcode activity.

Software emulator of nuclear pulse generation with different pulse shapes and pile-up

Energy Technology Data Exchange (ETDEWEB)

Pechousek, Jiri, E-mail: jiri.pechousek@upol.cz [Department of Experimental Physics, Faculty of Science, Palacky University, 17. listopadu 1192/12, 771 46 Olomouc (Czech Republic); Konecny, Daniel [Department of Optics, Faculty of Science, Palacky University, 17. listopadu 1192/12, 77 146 Olomouc (Czech Republic); Novak, Petr; Kouril, Lukas; Kohout, Pavel [Department of Experimental Physics, Faculty of Science, Palacky University, 17. listopadu 1192/12, 771 46 Olomouc (Czech Republic); Celiktas, Cuneyt [Department of Physics, Faculty of Science, Ege University, Bornova, Izmir (Turkey); Vujtek, Milan [Department of Experimental Physics, Faculty of Science, Palacky University, 17. listopadu 1192/12, 771 46 Olomouc (Czech Republic)

2016-08-21

The optimal detection of output signals from nuclear counting devices represents one of the key physical factors that govern accuracy and experimental reproducibility. In this context, the fine calibration of the detector under diverse experimental scenarios, although time costly, is necessary. However this process can be rendered easier with the use of systems that work in lieu of emulators. In this report we describe an innovative programmable pulse generator device capable to emulate the scintillation detector signals, in a way to mimic the detector performances under a variety of experimental conditions. The emulator generates a defined number of pulses, with a given shape and amplitude in the form of a sampled detector signal. The emulator output is then used off-line by a spectrometric system in order to set up its optimal performance. Three types of pulse shapes are produced by our device, with the possibility to add noise and pulse pile-up effects into the signal. The efficiency of the pulse detection, pile-up rejection and/or correction, together with the dead-time of the system, are therein analyzed through the use of some specific algorithms for pulse processing, and the results obtained validate the beneficial use of emulators for the accurate calibration process of spectrometric systems.

Long-term stability investigation of o/w cosmetic creams stabilized by mixed emulsifier

Directory of Open Access Journals (Sweden)

Đekić Ljiljana M.

2012-01-01

Full Text Available Polyglyceryl-3 Methylglucose Distearate (PMD, TEGO® Care 450, Evonik, Germanyis natural (vegetable, non-ionic, PEG-free emulsifier, suitable for the formulation of oil-in-water (o/w cosmetic creams and lotions. The oil phase components can be selected from mineral oils, vegetable oils and synthetic esters, which enable different variety of application profile of these emulsions. It is possible to prepare stable emulsions using low-level concentration of the PMD (2-3% if lotions contain 10-25%, and creams 20-40 % of oil phase. PMD forms liquid crystal structure in the presence of stearic acid, glyceryl stearate, fatty alcohols, or their combinations. The o/w type creams, stabilized by these mixed emulsifiers are complex, multiphase systems. The aim of this work was to formulate, prepare and investigate long-term stability of the o/w creams stabilized by mixed emulsifier polyglyceryl-3 methylglucose distearate/glyceryl stearate/stearyl alcohol, depending on concentration levels of PMD (2% or 3% and oil:water phase ratio (20:80 and 30:70. The samples were prepared using hot/hot procedure. Organoleptic inspection, centrifugation test, rheological measurements, electric conductivity and pH value measurements were performed 72 h, 1, 3, 12 and 30 months after preparation. The prepared samples were apparently white and homogenous creams. The consistency and homogeneity were preserved after centrifugation of the creams after 72 h, 1, 3, 12 and 30 months storage, and no phase separation could be detected. The pH values obtained are suitable for skin application. Conductivity values (25.2-63.7 μS cm1, 72 h after preparation were attributed to the multiple phase o/w emulsions with high percentages of fixed water. Results of the rheological measurements have shown that the investigated creams exhibited non-Newtonian thyxotropic behavior. The concentration of emulsifier PMD and oil phase content had an influence on the rheological parameters of investigated

The Mira-Titan Universe. II. Matter Power Spectrum Emulation

Energy Technology Data Exchange (ETDEWEB)

Lawrence, Earl; Heitmann, Katrin; Kwan, Juliana; Upadhye, Amol; Bingham, Derek; Habib, Salman; Higdon, David; Pope, Adrian; Finkel, Hal; Frontiere, Nicholas

2017-09-20

We introduce a new cosmic emulator for the matter power spectrum covering eight cosmological parameters. Targeted at optical surveys, the emulator provides accurate predictions out to a wavenumber k similar to 5 Mpc(-1) and redshift z <= 2. In addition to covering the standard set of Lambda CDM parameters, massive neutrinos and a dynamical dark energy of state are included. The emulator is built on a sample set of 36 cosmological models, carefully chosen to provide accurate predictions over the wide and large parameter space. For each model, we have performed a high-resolution simulation, augmented with 16 medium-resolution simulations and TimeRG perturbation theory results to provide accurate coverage over a wide k-range; the data set generated as part of this project is more than 1.2Pbytes. With the current set of simulated models, we achieve an accuracy of approximately 4%. Because the sampling approach used here has established convergence and error-control properties, follow-up results with more than a hundred cosmological models will soon achieve similar to 1% accuracy. We compare our approach with other prediction schemes that are based on halo model ideas and remapping approaches.

Validation of FORTRAN emulators for the G2 varian control programs

International Nuclear Information System (INIS)

Delorme, G.

1996-01-01

The extensive use of the Gentilly full scope simulator for training and verification of plant procedures, forced the development of a reliable desktop simulator for software maintenance purposes. For that we needed emulators for the control programs which run on the DCC Varian computers in the full scope simulator. This paper presents the validation results for the Reactor Regulating System (RRS) program. This emulator was programmed in a modular fashion providing ease of maintenance and of transportation to another environment. The results obtained with specific tests or with integrated testing involving complex control rule interactions, compared favorably with the ones obtained using the actual plant control programs running on the full scope simulator, which constitutes an irrefutable validation procedure. This RRS package along with the other emulators being validated In this manner could be used in safety codes with confidence. (author)

MPPT algorithm test on a photovoltaic emulating system constructed by a DC power supply and an indoor solar panel

International Nuclear Information System (INIS)

Zhou, Z.; Holland, P.M.; Igic, P.

2014-01-01

Highlights: • A novel PV emulator is constructed by using conventional solar panels with a DC power supply. • The proposed PV emulator is cost-effectiveness, relatively easy implementation. • The proposed PV emulator avoids the bandwidth problem associated with electronics PV emulators. • Indoor testing of MPPT algorithms and power converters avoids the dependency on solar irradiation. • The PV emulating system has been used for testing a P and O MPPT algorithm and a boost dc converter. - Abstract: In this paper a novel photovoltaic (PV) emulating scheme for testing maximum power point tracking (MPPT) algorithms and PV inverters has been proposed. It is constructed by the parallel connection of conventional solar panels with a DC power supply operating in current source mode. The advantages of the proposed scheme are cost-effectiveness, relatively easy implementation and indoor testing of MPPT algorithms and power converters avoiding weather and time of day dependency on solar irradiation levels. Furthermore, the proposed PV emulator avoids the bandwidth problem associated with the dc converter based PV emulating systems. Detailed circuit connection, parameters, electrical characteristics and mathematical model of the PV emulator are presented and discussed. Proposed PV emulating system has been used to test a boost DC/DC converter controlled by Perturb and Observe (P and O) MPPT algorithm. Test results confirmed the effectiveness of the proposed PV emulation system and all achieved results correspond well to the original designed values

Co-Emulation of Scan-Chain Based Designs Utilizing SCE-MI Infrastructure

OpenAIRE

Tomas, Bill Jason; Jiang, Yingtao; Yang, Mei

2014-01-01

As the complexity of the scan algorithm is dependent on the number of design registers, large SoC scan designs can no longer be verified in RTL simulation unless partitioned into smaller sub - blocks. This paper proposes a meth odology to decrease scan - chain verification time utilizing SCE - MI, a widely used communication protocol for emulation, and an FPGA - based emulation platform. A high - level (SystemC) testbench and FPGA synthesizable har...

PROPRIEDADES EMULSIFICANTES E SOLUBILIDADE DA CASEÍNA BOVINA E DE SEUS HIDROLISADOS TRÍPTICOS: 1. EFEITO DO PH E DO TEMPO DE HIDRÓLISE EMULSIFYING PROPERTIES AND SOLUBILITY OF CASEIN AND IT’S TRYPTIC HYDROLYSATES: 1. EFFECTS OF PH AND HYDROLYSIS TIME

Directory of Open Access Journals (Sweden)

Ângela Jardim DUARTE

1998-08-01

Full Text Available Visando a aplicação industrial da caseína e de seus hidrolisados trípticos, foram estudados os efeitos da variação do pH e do tempo de hidrólise sobre suas características de solubilidade e propriedades emulsificantes. Testou-se os valores de pH de 3,0; 4,0; 5,0; 6,0; 7,0 e 8,0 e os tempos de hidrólise: 5, 10 15, 30 e 60min. Foram medidos a solubilidade, a capacidade emulsificante, o índice de atividade emulsificante, a estabilidade da emulsão, e calculdado o tamanho dos glóbulos de gordura. Os resultados obtidos para a caseína nativa indicaram que os melhores valores para estas propriedades funcionais foram encontrados em pH acima de 5,0. A hidrólise tríptica da caseína foi benéfica para sua solubilidade e capacidade emulsificante e prejudicou sua estabilidade, em todos os valores de pH e tempos de hidrólise, exceto no pH 5,0 com 5 min de reação. Por outro lado, este tratamento enzimático contribuiu para melhorar o índice de atividade emulsificante da caseína, entre valores de pH 3,0 e 5,0 e após 10 min de reação.The effects of pH and hydrolysis time on the solubility and emulsifying properties were studied, in view of the industrial application of casein and its tryptic hydrolyzates. It has been tested the pH values of 3,0; 4,0; 5,0; 6,0; 7,0 and 8,0 and the reaction times: 5, 10, 15, 30 and 60 min. It has been evaluated the solubility, the emulsifying capacity, the emulsifying activity index and the emulsion stability. The results show that the best values for the functional properties of native casein were achieved at pH above 5,0. The tryptic hydrolysis of casein favored the solubility and emulsifying capacity but reduced the emulsion stability, at all pH and hydrolysis times, except in pH 5,0 with 5min of reaction. Otherwise, this enzymatic treatment improved the emulsifying activity index of casein only between pH 3,0- 5,0, after 10 min of reaction.

Emulsifying triglycerides with dairy phospholipids instead of soy lecithin modulates gut lipase activity

DEFF Research Database (Denmark)

Mathiassen, Jakob Hovalt; Nejrup, Rikke Guldhammer; Frøkiær, Hanne

2015-01-01

in particular to limit fatty acid absorption in babies given infant formulas. Since interaction between the lipid droplet and the gastric and duodenal lipases occur through the hydrophobic/hydrophilic interface, the composition of the emulsifier may be crucial for efficient hydrolysis. We therefore determined...... hydrolytic rate of gastric lipase and pancreatic lipase, on their own or pancreatic lipase after gastric lipase on TAG droplets of similar size emulsified in either soy lecithin (SL) or in bovine milk phospholipids (MPL), more similar to human milk globule membrane lipids than soy lecithin. Gastric lipase...... for formulas for term-born infants....

Synthesis of quaternary derivatives of ortho-coco di-amido toluene and investigation of these compounds as cationic bitumen emulsifier

Energy Technology Data Exchange (ETDEWEB)

Hassanzadeh, Masoumeh; Tayebi, Leila; Dezfouli, Hedieh; Kambarani, Masoud; Avval, Parviz Ahmadi [Tehran Univ. (Iran, Islamic Republic of). ACECR, Designing Chemical Process Research Group

2012-05-15

Bitumen emulsions are preferred over conventional pavement systems due to their biologically and environmentally acceptable formulation, safety, low viscosity, storage stability, and cost effectiveness. The present investigation deals with the systematic study to synthesize ortho-cocodi-amido toluene and four quaternary derivatives by amidation of coconut oil and ortho toluene diamine (OTD), followed by quaternization with formaldehyde, formic acid mixture, and acrylonitrile, resulted in a new quaternary compound useful as cationic emulsifier in bitumen emulsions. The roles of temperature and reaction time in determining optimum conditions were investigated as well. Emulsifying behavior of these quaternary compounds was studied by sieve residue test, settlement and storage stability test of emulsified asphalt, and water solubility. The results show that the acrylonitrile imidazolinium derivative of o-cocodi-amido toluene (VI) can be used as a rapid-medium setting emulsifier. (orig.)

Quantum Emulation of Gravitational Waves.

Science.gov (United States)

Fernandez-Corbaton, Ivan; Cirio, Mauro; Büse, Alexander; Lamata, Lucas; Solano, Enrique; Molina-Terriza, Gabriel

2015-07-14

Gravitational waves, as predicted by Einstein's general relativity theory, appear as ripples in the fabric of spacetime traveling at the speed of light. We prove that the propagation of small amplitude gravitational waves in a curved spacetime is equivalent to the propagation of a subspace of electromagnetic states. We use this result to propose the use of entangled photons to emulate the evolution of gravitational waves in curved spacetimes by means of experimental electromagnetic setups featuring metamaterials.

A calibration and data assimilation method using the Bayesian MARS emulator

International Nuclear Information System (INIS)

Stripling, H.F.; McClarren, R.G.; Kuranz, C.C.; Grosskopf, M.J.; Rutter, E.; Torralva, B.R.

2013-01-01

Highlights: ► We outline a transparent, flexible method for the calibration of uncertain inputs to computer models. ► We account for model, data, emulator, and measurement uncertainties. ► The method produces improved predictive results, which are validated using leave one-out experiments. ► Our implementation leverages the Bayesian MARS emulator, but any emulator may be substituted. -- Abstract: We present a method for calibrating the uncertain inputs to a computer model using available experimental data. The goal of the procedure is to estimate the posterior distribution of the uncertain inputs such that when samples from the posterior are used as inputs to future model runs, the model is more likely to replicate (or predict) the experimental response. The calibration is performed by sampling the space of the uncertain inputs, using the computer model (or, more likely, an emulator for the computer model) to assign weights to the samples, and applying the weights to produce the posterior distributions and generate predictions of new experiments with confidence bounds. The method is similar to Metropolis–Hastings calibration methods with independently sampled updates, except that we generate samples beforehand and replace the candidate acceptance routine with a weighting scheme. We apply our method to the calibration of a Hyades 2D model of laser energy deposition in beryllium. We employ a Bayesian Multivariate Adaptive Regression Splines (BMARS) emulator as a surrogate for Hyades 2D. We treat a range of uncertainties in our application, including uncertainties in the experimental inputs, experimental measurement error, and systematic experimental timing errors. The resulting posterior distributions agree with our existing intuition, and we validate the results by performing a series of leave-one-out predictions. We find that the calibrated predictions are considerably more accurate and less uncertain than blind sampling of the forward model alone.

An Emulator Toolbox to Approximate Radiative Transfer Models with Statistical Learning

Directory of Open Access Journals (Sweden)

Juan Pablo Rivera

2015-07-01

Full Text Available Physically-based radiative transfer models (RTMs help in understanding the processes occurring on the Earth’s surface and their interactions with vegetation and atmosphere. When it comes to studying vegetation properties, RTMs allows us to study light interception by plant canopies and are used in the retrieval of biophysical variables through model inversion. However, advanced RTMs can take a long computational time, which makes them unfeasible in many real applications. To overcome this problem, it has been proposed to substitute RTMs through so-called emulators. Emulators are statistical models that approximate the functioning of RTMs. Emulators are advantageous in real practice because of the computational efficiency and excellent accuracy and flexibility for extrapolation. We hereby present an “Emulator toolbox” that enables analysing multi-output machine learning regression algorithms (MO-MLRAs on their ability to approximate an RTM. The toolbox is included in the free-access ARTMO’s MATLAB suite for parameter retrieval and model inversion and currently contains both linear and non-linear MO-MLRAs, namely partial least squares regression (PLSR, kernel ridge regression (KRR and neural networks (NN. These MO-MLRAs have been evaluated on their precision and speed to approximate the soil vegetation atmosphere transfer model SCOPE (Soil Canopy Observation, Photochemistry and Energy balance. SCOPE generates, amongst others, sun-induced chlorophyll fluorescence as the output signal. KRR and NN were evaluated as capable of reconstructing fluorescence spectra with great precision. Relative errors fell below 0.5% when trained with 500 or more samples using cross-validation and principal component analysis to alleviate the underdetermination problem. Moreover, NN reconstructed fluorescence spectra about 50-times faster and KRR about 800-times faster than SCOPE. The Emulator toolbox is foreseen to open new opportunities in the use of advanced

Stabilizing effect of cetostearyl alcohol and glyceryl monostearate as co-emulsifiers on hydrocarbon-free O/W glyceride creams.

Science.gov (United States)

Ballmann, C; Mueller, B W

2008-01-01

The structure of a stable O/W cream is characterized by a more or less pronounced mixed crystal bilayer. The addition of co-emulsifiers in order to achieve a soft formulation often leads to a mixed crystal bilayer network of high viscosity and even phase separation. In order to ovoid this components of different chemical identities are used which often are not inert or harmless if they are absorbed. For this reason it seems to be interesting to use only components from one chemical family, e.g. to use only glycerides and their derivatives because in the case of absorption they are metabolized. The disadvantages of glyceride creams are, however, their low viscosity. The aim of this investigation was to find the optimum amount of co-emulsifier as consistency excipient for the basic formulation of an O/W glyceride cream. This was achieved by using differential scanning calorimetry; thermogravimetry, oscillation rheology and various stress tests. The amount of co-emulsifier used should not be too high, as it would crystallize increasingly during storage which gives the preparation an optical inhomogenity and a lack in softness which is needed for a suitable cosmetic acceptance. A slightly higher concentration than is necessary for the mixed emulsifier system can be advantageous, as the formation of a separate crystalline lipophilic network in the preparation increases its viscosity which will lead to a higher physico-chemical stability of the formulation. These results were obtained with the co-emulsifiers glyceryl monostearate (Imwitor 900), cetylstearyl alcohol (Lanette O), and PEG-20-glycerolstearate (Tagat S2) as O/W emulsifier. As oil phase a mixture of Miglyol 812 (caprylic/capric triglyceride) and Avocado oil was used.

A physics informed emulator for laser-driven radiating shock simulations

International Nuclear Information System (INIS)

McClarren, Ryan G.; Ryu, D.; Paul Drake, R.; Grosskopf, Michael; Bingham, Derek; Chou, Chuan-Chih; Fryxell, Bruce; Holst, Bart van der; Paul Holloway, James; Kuranz, Carolyn C.; Mallick, Bani; Rutter, Erica; Torralva, Ben R.

2011-01-01

This work discusses the uncertainty quantification aspect of quantification of margin and uncertainty (QMU) in the context of two linked computer codes. Specifically, we present a physics based reduction technique to deal with functional data from the first code and then develop an emulator for this reduced data. Our particular application deals with conditions created by laser deposition in a radiating shock experiment modeled using the Lagrangian, radiation-hydrodynamics code Hyades. Our goal is to construct an emulator and perform a sensitivity analysis of the functional output from Hyades to be used as an initial condition for a three-dimensional code that will compute the evolution of the radiating shock at later times. Initial attempts at purely statistical data reduction techniques, were not successful at reducing the number of parameters required to describe the Hyades output. We decided on an alternate approach using physical arguments to decide what features/locations of the output were relevant (e.g., the location of the shock front or the location of the maximum pressure) and then used a piecewise linear fit between these locations. This reduced the number of outputs needed from the emulator to 40, down from the O(1000) points in the Hyades output. Then, using Bayesian MARS and Gaussian process regression, we were able to build emulators for Hyades and study sensitivities to input parameters. - Highlights: → Uncertainty quantification for two linked computer codes is investigated. → We perform physics-based dimension reduction on the code output. → This reduces the uncertain degrees of freedom from hundreds to tens.

Characterization of industrial wastes as raw materials for Emulsified Modified Bitumen (EMB) formulation

Science.gov (United States)

Najib Razali, Mohd; Isa, Syarifah Nur Ezatie Mohd; Salehan, Noor Adilah Md; Musa, Musfafikri; Aziz, Mohd Aizudin Abd; Nour, Abdurahman Hamid; Yunus, Rosli Mohd

2018-04-01

This study was conducted to characterize industrial wastes for formulation of emulsified modified bitumen (EMB) in relation to their physical characteristic and elemental composition. This analysis will give information either raw materials from industrial wastes can be used for EMB formulation. Bitumen is produced from crude oil that is extracted from the ground which categorizes the crude oil as one of the non-renewable form of product. A vast environmental problem issues arises in Malaysia cause by the excessive manufacturing activity that lead to a miss-management of industrial waste has leads to the used of industrial waste in the EMB formulation. Industrial waste such as polystyrene, polyethylene and used automotive oil can be used as alternative to formulate bitumen. Then a suitable emulsifier needs to be added to produce the final product which is EMB. The emulsifier will yield a charge depends on its properties to bind the oily bitumen with water. Physical characteristic studies were performed by thermogravimetric Analysis (TGA), differential scanning calorimetry (DSC), flash point test, density rest and moisture content test. Fourier Transform Infrared Spectroscopy (FTIR) analysis was measured to determine the material’s molecular composition and structure.

Preparation, characterization and thermal properties of nanocapsules containing phase change material n-dodecanol by miniemulsion polymerization with polymerizable emulsifier

International Nuclear Information System (INIS)

Chen, Zhong-Hua; Yu, Fei; Zeng, Xing-Rong; Zhang, Zheng-Guo

2012-01-01

Highlights: ► We prepare nanocapsules containing n-dodecanol via miniemulsion polymerization. ► Polymerizable emulsifier plays important role in the preparation of nanocapsules. ► Adding co-emulsifier into water phase is helpful to encapsulate n-dodecanol. ► The phase change latent heat of nanocapsule is 98.8 J/g with temperature of 18.2 °C. -- Abstract: Nanocapsules containing phase change material (PCM) n-dodecanol as core and polymethyl methacrylate (PMMA) as shell were synthesized by miniemulsion polymerization with polymerizable emulsifier DNS-86 and co-emulsifier hexadecane (HD). The nanocapsules were characterized by using Fourier transform infrared spectroscopy (FTIR), transmission electron microscope (TEM), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and laser particle diameter analyzer. The effects of polymerizable emulsifier and co-emulsifier on the properties of nanocapsules were studied. The results show that thermal properties of nanocapsules are affected greatly by the addition methods of HD and the amounts of DNS-86 and HD. Adding HD into water phase is helpful for the encapsulation of n-dodecanol. When the mass ratios of DNS-86 to n-dodecanol and the mass ratios of HD to n-dodecanol were 3% and 2%, the phase change latent heat and the encapsulation efficiency of nanocapsules reached to the maximum value of 98.8 J/g and 82.2%, respectively. Spherical nanocapsules with mean diameter of 150 nm and phase change temperature of 18.2 °C are obtained, which are sure to have a good potential for energy storage.

Keeping gut lining at bay: impact of emulsifiers.

Science.gov (United States)

Cani, Patrice D; Everard, Amandine

2015-06-01

Obesity is associated with altered gut microbiota and low-grade inflammation. Both dietary habits and food composition contribute to the onset of such diseases. Emulsifiers, compounds commonly used in a variety of foods, were shown to induce body weight gain, low-grade inflammation and metabolic disorders. These dietary compounds promote gut microbiota alteration and gut barrier dysfunction leading to negative metabolic alterations. Copyright © 2015 Elsevier Ltd. All rights reserved.

Self-emulsifying drug delivery systems (SEDDS): formulation development, characterization, and applications.

Science.gov (United States)

Singh, Bhupinder; Bandopadhyay, Shantanu; Kapil, Rishi; Singh, Ramandeep; Katare, O

2009-01-01

Self-emulsifying drug delivery systems (SEDDS) possess unparalleled potential in improving oral bioavailability of poorly water-soluble drugs. Following their oral administration, these systems rapidly disperse in gastrointestinal fluids, yielding micro- or nanoemulsions containing the solubilized drug. Owing to its miniscule globule size, the micro/nanoemulsifed drug can easily be absorbed through lymphatic pathways, bypassing the hepatic first-pass effect. We present an exhaustive and updated account of numerous literature reports and patents on diverse types of self-emulsifying drug formulations, with emphasis on their formulation, characterization, and systematic optimization strategies. Recent advancements in various methodologies employed to characterize their globule size and shape, ability to encapsulate the drug, gastrointestinal and thermodynamic stability, rheological characteristics, and so forth, are discussed comprehensively to guide the formula-tor in preparing an effective and robust SEDDS formulation. Also, this exhaustive review offers an explicit discussion on vital applications of the SEDDS in bioavailability enhancement of various drugs, outlining an overview on myriad in vitro, in situ, and ex vivo techniques to assess the absorption and/ or permeation potential of drugs incorporated in the SEDDS in animal and cell line models, and the subsequent absorption pathways followed by them. In short, the current article furnishes an updated compilation of wide-ranging information on all the requisite vistas of the self-emulsifying formulations, thus paving the way for accelerated progress into the SEDDS application in pharmaceutical research.

Experimental Study of Using Emulsified Diesel Fuel on the Performance and Pollutants Emitted from Four Stroke Water Cooled Diesel Engine

Science.gov (United States)

Sakhrieh, A.; Fouad, R. H.; Yamin, J. A.

2009-08-01

A water-cooled, four stroke, four cylinder, direct injection diesel engine was used to study the effect of emulsified diesel fuel on the engine performance and on the main pollutant emissions. Emulsified diesel fuels of 0%, 5%, 10%, 15%, 20%, 25% and 30% water by volume were used. The experiments were conducted in the speed range from 1000 to 3000 rpm. It was found that, in general, using emulsified fuel improves the engine performance and reduces emissions. While the BSFC has a minimum value at 5% water and 2000 rpm, the torque, the BMEP and efficiency are found to have maximum values under these conditions. CO2 was found to increase with engine speed and to decrease with water content. NOx produced from emulsified fuel is significantly less than that produced from pure diesel under the same conditions.

ATM LAN Emulation: Getting from Here to There.

Science.gov (United States)

Learn, Larry L., Ed.

1995-01-01

Discusses current LAN (local area network) configuration and explains ATM (asynchronous transfer mode) as the future telecommunications transport. Highlights include LAN emulation, which enables the interconnection of legacy LANs and the new ATM environment; virtual LANs; broadcast servers; and standards. (LRW)

Treatment of emulsified oily wastewater by commercial scale electrocoagulation at Vancouver shipyards

Energy Technology Data Exchange (ETDEWEB)

Stephenson, R.J.; Tennant, B.D. [McKay Creek Technologies Ltd., North Vancouver, BC (Canada); Hartle, D.R. [Vancouver Shipping Co. Ltd., BC (Canada); Stuckert, B. [Quantum Environmental Group, Richmond, BC (Canada)

2002-06-01

Some of the emulsified oily wastewater generated by the Washington Marine Group fleet and the Vancouver shipyards are from sources such as bilge water, tank wash water from gas freeing operations, ballast water, and wastewater from pressure washing equipment. The Washington Marine Group is the largest shipbuilding, ship maintenance and repair, and marine transportation company in Canada, a group to which McKay Creek Technologies belongs. A investigation was performed in an attempt to find commercially viable means of treating this wastewater. McKay Creek Technologies developed its own cleaning process. Electrocoagulation is a process based on the use of an electrical current in an electrochemical cell to coagulate contaminants in wastewater. With three years of experience gained by treating the wastewater of the Washington Marine Group operations at Vancouver shipyards using this technology, McKay Creek Technologies has found ways to treat emulsified oily wastewater simply and effectively. It has been determined that electrocoagulation is an effective treatment method for emulsified oils, poly-nuclear aromatic hydrocarbons (PAHs), poorly settling solids, poorly soluble organics, contaminants which add turbidity to water, and negatively charged metal species like arsenic, molybdenum, and phosphate. A brief history of electrocoagulation was provided, and the authors explained the process and how it was applied to the situation at Vancouver shipyards. 2 refs., 5 tabs., 1 fig.

A Voltage Mode Memristor Bridge Synaptic Circuit with Memristor Emulators

Directory of Open Access Journals (Sweden)

Leon Chua

2012-03-01

Full Text Available A memristor bridge neural circuit which is able to perform signed synaptic weighting was proposed in our previous study, where the synaptic operation was verified via software simulation of the mathematical model of the HP memristor. This study is an extension of the previous work advancing toward the circuit implementation where the architecture of the memristor bridge synapse is built with memristor emulator circuits. In addition, a simple neural network which performs both synaptic weighting and summation is built by combining memristor emulators-based synapses and differential amplifier circuits. The feasibility of the memristor bridge neural circuit is verified via SPICE simulations.

A Reactive and Cycle-True IP Emulator for MPSoC Exploration

DEFF Research Database (Denmark)

Mahadevan, Shankar; Angiolini, Federico; Sparsø, Jens

2008-01-01

The design of MultiProcessor Systems-on-Chip (MPSoC) emphasizes intellectual-property (IP)-based communication-centric approaches. Therefore, for the optimization of the MPSoC interconnect, the designer must develop traffic models that realistically capture the application behavior as executing...... on the IP core. In this paper, we introduce a Reactive IP Emulator (RIPE) that enables an effective emulation of the IP-core behavior in multiple environments, including bit and cycle-true simulation. The RIPE is built as a multithreaded abstract instruction-set processor, and it can generate reactive...

Natural emulsifiers - Biosurfactants, phospholipids, biopolymers, and colloidal particles: Molecular and physicochemical basis of functional performance.

Science.gov (United States)

McClements, David Julian; Gumus, Cansu Ekin

2016-08-01

There is increasing consumer pressure for commercial products that are more natural, sustainable, and environmentally friendly, including foods, cosmetics, detergents, and personal care products. Industry has responded by trying to identify natural alternatives to synthetic functional ingredients within these products. The focus of this review article is on the replacement of synthetic surfactants with natural emulsifiers, such as amphiphilic proteins, polysaccharides, biosurfactants, phospholipids, and bioparticles. In particular, the physicochemical basis of emulsion formation and stabilization by natural emulsifiers is discussed, and the benefits and limitations of different natural emulsifiers are compared. Surface-active polysaccharides typically have to be used at relatively high levels to produce small droplets, but the droplets formed are highly resistant to environmental changes. Conversely, surface-active proteins are typically utilized at low levels, but the droplets formed are highly sensitive to changes in pH, ionic strength, and temperature. Certain phospholipids are capable of producing small oil droplets during homogenization, but again the droplets formed are highly sensitive to changes in environmental conditions. Biosurfactants (saponins) can be utilized at low levels to form fine oil droplets that remain stable over a range of environmental conditions. Some nature-derived nanoparticles (e.g., cellulose, chitosan, and starch) are effective at stabilizing emulsions containing relatively large oil droplets. Future research is encouraged to identify, isolate, purify, and characterize new types of natural emulsifier, and to test their efficacy in food, cosmetic, detergent, personal care, and other products. Copyright © 2016 Elsevier B.V. All rights reserved.

Yield emulsifiers exopolysaccharides produced by native halophilic bacteria concentrations molasses three Saccharum officinarum L. "sugarcane"

Directory of Open Access Journals (Sweden)

Ángel Fuentes, Carmen Carreño

2013-06-01

Full Text Available The microbial exopolysaccharide with emulsifying properties are an alternative to polymers and chemicals from algae and plants. Its production in molasses as carbon source lowers costs and generates added value to this byproduct of the sugar industry, so the aim of this study was to determine the performance and productivity of EPS emulsifiers by native halophilic bacteria in 20, 30 and 40 gL-1 of molasses. In MY synthetic medium with 5 % w/v of salts, 138 isolates of bacteria obtained from soil samples of salt water and in the districts of San Jose and Santa Rosa, in Lambayeque. In 10.8 % of these gummy colony forming bacteria and grown on glucose as carbon source EPS recovered whose maximum values of the mixtures in water emulsion - oil phase were 63.3 and 56.6 % after 1 and 24 hours, respectively. The M5 bacteria identified as Halomonas C1 10-1 sp. M5 EPS synthesized emulsifiers molasses broth, reaching yields Yp/s of 0.296 gg-1 and 0.200 gg-1 with 20 and 30 gL-1 of molasses respectively, a productivity of 0.016 and 0.017 gL-1 h -1 , not differing significantly between them. With 10 gL-1 glucose was reached Yp/s of 0.171 gg-1 and a productivity of 0.018 gL-1 h -1 . It was shown that the EPS produced native halophilic bacteria utilizing molasses emulsifiers as carbon source.

An alkyl polyglucoside-mixed emulsifier as stabilizer of emulsion systems: the influence of colloidal structure on emulsions skin hydration potential.

Science.gov (United States)

Savic, Snezana; Lukic, Milica; Jaksic, Ivana; Reichl, Stephan; Tamburic, Slobodanka; Müller-Goymann, Christel

2011-06-01

To be considered as a suitable vehicle for drugs/cosmetic actives, an emulsion system should have a number of desirable properties mainly dependent on surfactant used for its stabilization. In the current study, C(12-14) alkyl polyglucoside (APG)-mixed emulsifier of natural origin has been investigated in a series of binary (emulsifier concentration 10-25% (w/w)) and ternary systems with fixed emulsifier content (15% (w/w)) with or without glycerol. To elucidate the systems' colloidal structure the following physicochemical techniques were employed: polarization and transmission electron microscopy, X-ray diffraction (WAXD and SAXD), thermal analysis (DSC and TGA), complex rheological, pH, and conductivity measurements. Additionally, the emulsion vehicles' skin hydration potential was tested in vivo, on human skin under occlusion. In a series of binary systems with fixed emulsifier/water ratios ranging from 10/90 to 25/75 the predominance of a lamellar mesophase was found, changing its character from a liquid crystalline to a gel crystalline type. The same was observed in gel emulsions containing equal amounts of emulsifier and oil (15% (w/w)), but varying in glycerol content (0-25%). Different emulsion samples exhibited different water distribution modes in the structure, reflecting their rheological behavior and also their skin hydration capacity. Copyright © 2011 Elsevier Inc. All rights reserved.

Multi-level emulation of complex climate model responses to boundary forcing data

Science.gov (United States)

Tran, Giang T.; Oliver, Kevin I. C.; Holden, Philip B.; Edwards, Neil R.; Sóbester, András; Challenor, Peter

2018-04-01

Climate model components involve both high-dimensional input and output fields. It is desirable to efficiently generate spatio-temporal outputs of these models for applications in integrated assessment modelling or to assess the statistical relationship between such sets of inputs and outputs, for example, uncertainty analysis. However, the need for efficiency often compromises the fidelity of output through the use of low complexity models. Here, we develop a technique which combines statistical emulation with a dimensionality reduction technique to emulate a wide range of outputs from an atmospheric general circulation model, PLASIM, as functions of the boundary forcing prescribed by the ocean component of a lower complexity climate model, GENIE-1. Although accurate and detailed spatial information on atmospheric variables such as precipitation and wind speed is well beyond the capability of GENIE-1's energy-moisture balance model of the atmosphere, this study demonstrates that the output of this model is useful in predicting PLASIM's spatio-temporal fields through multi-level emulation. Meaningful information from the fast model, GENIE-1 was extracted by utilising the correlation between variables of the same type in the two models and between variables of different types in PLASIM. We present here the construction and validation of several PLASIM variable emulators and discuss their potential use in developing a hybrid model with statistical components.

Effect of antioxidant properties of lecithin emulsifier on oxidative stability of encapsulated bioactive compounds.

Science.gov (United States)

Pan, Yuanjie; Tikekar, Rohan V; Nitin, N

2013-06-25

Oxidation of encapsulated bioactive compounds in emulsions is one of the key challenges that limit shelf life of emulsion containing products. Oxidation in these emulsions is triggered by permeation of free radicals generated at the emulsion interface. The objective of this study was to evaluate the role of antioxidant properties of common emulsifiers (lecithin and Tween 20) in reducing permeation of free radicals across the emulsion interface. Radical permeation rates were correlated with oxidative stability of a model bioactive compound (curcumin) encapsulated in these emulsions. Rate of permeation of peroxyl radicals from the aqueous phase to the oil phase of emulsion was inversely proportional to the antioxidant properties of emulsifiers. The rate of radical permeation was significantly higher (plecithin compared to native lecithin that showed higher antioxidant activity. Free radical permeation rate correlated with stability of curcumin in emulsions and was significantly higher (plecithin stabilized emulsions as compared to Tween 20 emulsions. Overall, this study demonstrates that antioxidant activity of emulsifiers significantly influences permeation of free radicals across the emulsion interface and the rate of oxidation of bioactive encapsulant. Copyright © 2013 Elsevier B.V. All rights reserved.

Ultrasound Assisted Synthesis of Hydroxylated Soybean Lecithin from Crude Soybean Lecithin as an Emulsifier.

Science.gov (United States)

Chiplunkar, Pranali P; Pratap, Amit P

2017-10-01

Soybean lecithin is a by-product obtained during degumming step of crude soybean oil refining. Crude soybean lecithin (CSL) contains major amount of phospholipids (PLs) along with minor amount of acylglycerols, bioactive components, etc. Due to presence of PLs, CSL can be used as an emulsifier. Crude soybean lecithin (CSL) was utilized to synthesize hydroxylated soybean lecithin (HSL) by hydroxylation using hydrogen peroxide and catalytic amount of lactic acid to enhance the hydrophilicity and emulsifying properties of CSL. To reduce the reaction time and to increase rate of reaction, HSL was synthesized under ultrasound irradiation. The effect of different operating parameters such as lactic acid, hydrogen peroxide, temperature, ultrasonic power and duty cycle in synthesis of HSL were studied and optimized. The surface tension (SFT), interfacial tension (IFT) and the critical micelle concentration (CMC) of the HSL (26.11 mN/m, 2.67 mN/m, 112 mg/L) were compared to CSL (37.53 mN/m, 6.22 mN/m, 291 mg/L) respectively. The HSL has better emulsion stability and low foaming characteristics as compared to CSL. Therefore, the product as an effective emulsifier can be used in food, pharmacy, lubricant, cosmetics, etc.

A novel betaine type asphalt emulsifier synthesized and investigated by online FTIR spectrophotometric method

Directory of Open Access Journals (Sweden)

Shi Laishun

2015-01-01

Full Text Available A novel betaine type asphalt emulsifier 3-(N,N,N-dimethyl acetoxy ammonium chloride-2-hydroxypropyl laurate was synthesized after three steps by the reaction of lauric acid, epichlorohydrin, dimethylamine and sodium chloroacetate. The optimum reaction conditions were obtained for the synthesis of the first step of 3-chloro-2-hydroxypropyl laurate. The esterification yield reaches 97.1% at the optimum conditions of reaction temperature 80ºC, reaction time 6 h, feedstock mole ratio of epichlorohydrin to lauric acid 1.5, mass ratio of catalyst to lauric acid 2%. The chemical structure of the product was characterized by FTIR and 1H NMR. The first synthesis step of 3-chloro-2-hydroxypropyl laurate was monitored by online FTIR technique. The by-product was detected by the online FTIR analysis. Based upon the experimental data, a plausible reaction mechanism was proposed for the reaction. The CMC of the objective product has a lower value of 7.4×10-4 mol/L. The surface tension at CMC is 30.85 mN/m. The emulsifier is a rapid-set asphalt emulsifier.

Effect of mixing mode and emulsifying agents on micro/nanoencapsulation of low viscosity self-healing agents in polymethyl methacrylate shell

Science.gov (United States)

Ahangaran, Fatemeh; Navarchian, Amir H.; Hayaty, Mehran; Esmailpour, Karim

2016-09-01

In this study, epoxy prepolymer (EC 157) and pentaerythritol tetrakis (3-mercaptopropionate) (PETMP) as hardener were encapsulated separately in polymethyl methacrylate (PMMA) shells through an internal phase separation method. Chemical structures, morphologies, and thermal properties of healing agent micro/nanocapsules were characterized by Fourier transform infrared (FT-IR) spectroscopy, field emission scanning electron microscopy (FESEM), and thermal gravimetric analysis (TGA) respectively. The effects of encapsulation processing conditions such as mechanical mixing rate, ultrasonication, emulsifier type, and co-emulsifier concentration on encapsulation yield, capsule mean diameter and core content were studied using the Taguchi experimental design approach. The results indicated that the main significant factors affecting the yield of encapsulation are emulsifier type and ultrasonication. The most important factors which affect the mean diameter of capsules are emulsifier type and mechanical mixing rate. The core content was influenced by ultrasonication and mechanical mixing rate. The relative optimum condition of encapsulation was also determined using overall evaluation criteria.

Real-Time Emulation of Nonstationary Channels in Safety-Relevant Vehicular Scenarios

Directory of Open Access Journals (Sweden)

Golsa Ghiaasi

2018-01-01

Full Text Available This paper proposes and discusses the architecture for a real-time vehicular channel emulator capable of reproducing the input/output behavior of nonstationary time-variant radio propagation channels in safety-relevant vehicular scenarios. The vehicular channel emulator architecture aims at a hardware implementation which requires minimal hardware complexity for emulating channels with the varying delay-Doppler characteristics of safety-relevant vehicular scenarios. The varying delay-Doppler characteristics require real-time updates to the multipath propagation model for each local stationarity region. The vehicular channel emulator is used for benchmarking the packet error performance of commercial off-the-shelf (COTS vehicular IEEE 802.11p modems and a fully software-defined radio-based IEEE 802.11p modem stack. The packet error ratio (PER estimated from temporal averaging over a single virtual drive and the packet error probability (PEP estimated from ensemble averaging over repeated virtual drives are evaluated and compared for the same vehicular scenario. The proposed architecture is realized as a virtual instrument on National Instruments™ LabVIEW. The National Instrument universal software radio peripheral with reconfigurable input-output (USRP-Rio 2953R is used as the software-defined radio platform for implementation; however, the results and considerations reported are of general purpose and can be applied to other platforms. Finally, we discuss the PER performance of the modem for two categories of vehicular channel models: a vehicular nonstationary channel model derived for urban single lane street crossing scenario of the DRIVEWAY’09 measurement campaign and the stationary ETSI models.

UPEML, Computer Independent Emulator of CDC Update Utility

International Nuclear Information System (INIS)

2002-01-01

1 - Description of program or function: UPEML is a machine-portable CDC UPDATE emulation program. It is capable of emulating a significant subset of the standard CDC UPDATE functions, including program library creation and subsequent modification. 2 - Method of solution: UPEML was originally written to facilitate the use of CDC-based scientific packages on alternate computers. In addition to supporting computers such as the VAX/VMS, IBM, and CRAY/COS, Version 3.0 now supports UNIX workstations and the CRAY/UNICOS operating system. Several program bugs have been corrected in Version 3.0. Version 3.0 has several new features including 1) improved error checking, 2) the ability to use *ADDFILE and READ from nested files, 3) creation of compile file on creation, 4) allows identifiers to begin with numbers, and 5) ability to control warning messages and program termination on error conditions. 3 - Restrictions on the complexity of the problem: None noted

Development of the CELSS emulator at NASA. Johnson Space Center

Science.gov (United States)

Cullingford, Hatice S.

1990-01-01

The Closed Ecological Life Support System (CELSS) Emulator is under development. It will be used to investigate computer simulations of integrated CELSS operations involving humans, plants, and process machinery. Described here is Version 1.0 of the CELSS Emulator that was initiated in 1988 on the Johnson Space Center (JSC) Multi Purpose Applications Console Test Bed as the simulation framework. The run model of the simulation system now contains a CELSS model called BLSS. The CELSS simulator empowers us to generate model data sets, store libraries of results for further analysis, and also display plots of model variables as a function of time. The progress of the project is presented with sample test runs and simulation display pages.

Microwave emulations and tight-binding calculations of transport in polyacetylene

Energy Technology Data Exchange (ETDEWEB)

Stegmann, Thomas, E-mail: stegmann@icf.unam.mx [Instituto de Ciencias Físicas, Universidad Nacional Autónoma de México, Avenida Universidad s/n, 62210 Cuernavaca (Mexico); Franco-Villafañe, John A., E-mail: jofravil@fis.unam.mx [Instituto de Física, Benemérita Universidad Autónoma de Puebla, Apartado Postal J-48, 72570 Puebla (Mexico); Instituto de Ciencias Físicas, Universidad Nacional Autónoma de México, Avenida Universidad s/n, 62210 Cuernavaca (Mexico); Ortiz, Yenni P. [Instituto de Ciencias Físicas, Universidad Nacional Autónoma de México, Avenida Universidad s/n, 62210 Cuernavaca (Mexico); Kuhl, Ulrich [Université de Nice – Sophia Antipolis, Laboratoire de la Physique de la Matière Condensée, CNRS, Parc Valrose, 06108 Nice (France); Mortessagne, Fabrice, E-mail: fabrice.mortessagne@unice.fr [Université de Nice – Sophia Antipolis, Laboratoire de la Physique de la Matière Condensée, CNRS, Parc Valrose, 06108 Nice (France); Seligman, Thomas H. [Instituto de Ciencias Físicas, Universidad Nacional Autónoma de México, Avenida Universidad s/n, 62210 Cuernavaca (Mexico); Centro Internacional de Ciencias, 62210 Cuernavaca (Mexico)

2017-01-05

A novel approach to investigate the electron transport of cis- and trans-polyacetylene chains in the single-electron approximation is presented by using microwave emulation measurements and tight-binding calculations. In the emulation we take into account the different electronic couplings due to the double bonds leading to coupled dimer chains. The relative coupling constants are adjusted by DFT calculations. For sufficiently long chains a transport band gap is observed if the double bonds are present, whereas for identical couplings no band gap opens. The band gap can be observed also in relatively short chains, if additional edge atoms are absent, which cause strong resonance peaks within the band gap. The experimental results are in agreement with our tight-binding calculations using the nonequilibrium Green's function method. The tight-binding calculations show that it is crucial to include third nearest neighbor couplings to obtain the gap in the cis-polyacetylene. - Highlights: • Electronic transport in individual polyacetylene chains is studied. • Microwave emulation experiments and tight-binding calculations agree well. • In long chains a band-gap opens due the dimerization of the chain. • In short chains edge atoms cause strong resonance peaks in the center of the band-gap.

Microwave emulations and tight-binding calculations of transport in polyacetylene

International Nuclear Information System (INIS)

Stegmann, Thomas; Franco-Villafañe, John A.; Ortiz, Yenni P.; Kuhl, Ulrich; Mortessagne, Fabrice; Seligman, Thomas H.

2017-01-01

A novel approach to investigate the electron transport of cis- and trans-polyacetylene chains in the single-electron approximation is presented by using microwave emulation measurements and tight-binding calculations. In the emulation we take into account the different electronic couplings due to the double bonds leading to coupled dimer chains. The relative coupling constants are adjusted by DFT calculations. For sufficiently long chains a transport band gap is observed if the double bonds are present, whereas for identical couplings no band gap opens. The band gap can be observed also in relatively short chains, if additional edge atoms are absent, which cause strong resonance peaks within the band gap. The experimental results are in agreement with our tight-binding calculations using the nonequilibrium Green's function method. The tight-binding calculations show that it is crucial to include third nearest neighbor couplings to obtain the gap in the cis-polyacetylene. - Highlights: • Electronic transport in individual polyacetylene chains is studied. • Microwave emulation experiments and tight-binding calculations agree well. • In long chains a band-gap opens due the dimerization of the chain. • In short chains edge atoms cause strong resonance peaks in the center of the band-gap.

An orbital emulator for pursuit-evasion game theoretic sensor management

Science.gov (United States)

Shen, Dan; Wang, Tao; Wang, Gang; Jia, Bin; Wang, Zhonghai; Chen, Genshe; Blasch, Erik; Pham, Khanh

2017-05-01

This paper develops and evaluates an orbital emulator (OE) for space situational awareness (SSA). The OE can produce 3D satellite movements using capabilities generated from omni-wheeled robot and robotic arm motion methods. The 3D motion of a satellite is partitioned into the movements in the equatorial plane and the up-down motions in the vertical plane. The 3D actions are emulated by omni-wheeled robot models while the up-down motions are performed by a stepped-motor-controlled-ball along a rod (robotic arm), which is attached to the robot. For multiple satellites, a fast map-merging algorithm is integrated into the robot operating system (ROS) and simultaneous localization and mapping (SLAM) routines to locate the multiple robots in the scene. The OE is used to demonstrate a pursuit-evasion (PE) game theoretic sensor management algorithm, which models conflicts between a space-based-visible (SBV) satellite (as pursuer) and a geosynchronous (GEO) satellite (as evader). The cost function of the PE game is based on the informational entropy of the SBV-tracking-GEO scenario. GEO can maneuver using a continuous and low thruster. The hard-in-loop space emulator visually illustrates the SSA problem solution based PE game.

Lipid composition and emulsifying properties of canola lecithin from enzymatic degumming.

Science.gov (United States)

Xie, Meizhen; Dunford, Nurhan Turgut

2017-03-01

This study investigated the polar lipid composition and emulsifying properties of canola lecithin from enzymatic degumming (CLED). Phospholipase A 1 was used for enzymatic degumming of crude canola oil to collect lecithin sample. Canola lecithin from water degumming (CLWD) was also collected and served as the control. The results showed that the contents of phosphatidylethanolamine (PE) (2.99%) and phosphatidylcholine (PC) (6.59%) in CLED were significantly lower than that in CLWD (PE 15.55% and PC 21.93%); while the content of lysophosphatidylcholine (LPC) (19.45%) in CLED was significantly higher than that in CLWD (3.27%). Unsaturated fatty acids accounted for a higher percentage of the total fatty acids in CLED than in CLWD. CLED promoted more stable o/w emulsions than CLWD. This study provides a better understanding of the chemical nature of CLED, and important information for utilization of CLED as o/w emulsifier. Copyright © 2016 Elsevier Ltd. All rights reserved.

Evidence for emulation in chimpanzees in social settings using the floating peanut task.

Directory of Open Access Journals (Sweden)

Claudio Tennie

Full Text Available BACKGROUND: It is still unclear which observational learning mechanisms underlie the transmission of difficult problem-solving skills in chimpanzees. In particular, two different mechanisms have been proposed: imitation and emulation. Previous studies have largely failed to control for social factors when these mechanisms were targeted. METHODS: In an attempt to resolve the existing discrepancies, we adopted the 'floating peanut task', in which subjects need to spit water into a tube until it is sufficiently full for floating peanuts to be grasped. In a previous study only a few chimpanzees were able to invent the necessary solution (and they either did so in their first trials or never. Here we compared success levels in baseline tests with two experimental conditions that followed: 1 A full model condition to test whether social demonstrations would be effective, and 2 A social emulation control condition, in which a human experimenter poured water from a bottle into the tube, to test whether results information alone (present in both experimental conditions would also induce successes. Crucially, we controlled for social factors in both experimental conditions. Both types of demonstrations significantly increased successful spitting, with no differences between demonstration types. We also found that younger subjects were more likely to succeed than older ones. Our analysis showed that mere order effects could not explain our results. CONCLUSION: The full demonstration condition (which potentially offers additional information to observers, in the form of actions, induced no more successes than the emulation condition. Hence, emulation learning could explain the success in both conditions. This finding has broad implications for the interpretation of chimpanzee traditions, for which emulation learning may perhaps suffice.

Emulation, imitation, over-imitation and the scope of culture for child and chimpanzee.

Science.gov (United States)

Whiten, Andrew; McGuigan, Nicola; Marshall-Pescini, Sarah; Hopper, Lydia M

2009-08-27

We describe our recent studies of imitation and cultural transmission in chimpanzees and children, which question late twentieth-century characterizations of children as imitators, but chimpanzees as emulators. As emulation entails learning only about the results of others' actions, it has been thought to curtail any capacity to sustain cultures. Recent chimpanzee diffusion experiments have by contrast documented a significant capacity for copying local behavioural traditions. Additionally, in recent 'ghost' experiments with no model visible, chimpanzees failed to replicate the object movements on which emulation is supposed to focus. We conclude that chimpanzees rely more on imitation and have greater cultural capacities than previously acknowledged. However, we also find that they selectively apply a range of social learning processes that include emulation. Recent studies demonstrating surprisingly unselective 'over-imitation' in children suggest that children's propensity to imitate has been underestimated too. We discuss the implications of these developments for the nature of social learning and culture in the two species. Finally, our new experiments directly address cumulative cultural learning. Initial results demonstrate a relative conservatism and conformity in chimpanzees' learning, contrasting with cumulative cultural learning in young children. This difference may contribute much to the contrast in these species' capacities for cultural evolution.

Emotions Targeting Moral Exemplarity: Making Sense of the Logical Geography of Admiration, Emulation and Elevation

Science.gov (United States)

Kristjánsson, Kristján

2017-01-01

Despite renewed interest in moral role-modelling and its emotional underpinnings, further conceptual work is needed on the logical geography of the emotions purportedly driving it, in particular, admiration, emulation and elevation. In this article, I explore admiration (as understood by Linda Zagzebski), emulation (as understood by Aristotle) and…

Interactions between iron, phenolic compounds, emulsifiers, and pH in omega-3-enriched oil-in-water emulsions

DEFF Research Database (Denmark)

Sørensen, Ann-Dorit Moltke; Haahr, Anne-Mette; Becker, E.M.

2008-01-01

The behavior of antioxidants in emulsions is influenced by several factors such as pH and emulsifier type. This study aimed to evaluate the interaction between selected food emulsifiers, phenolic compounds, iron, and pH and their effect on the oxidative stability of n-3 polyunsaturated lipids...... products. When iron was present, the pH was crucial for the formation of lipid oxidation products. At pH 3 some phenolic compounds, especially caffeic acid, reduced Fe3+ to Fe2+, and Fe2+ increased lipid oxidation at this pH compared to pH 6. Among the evaluated phenols, caffeic acid had the most...... significant effects, as caffeic acid was found to be prooxidative irrespective of pH, emulsifier type, and presence of iron, although the degrees of lipid oxidation were different at the different experimental conditions. The other evaluated phenols were prooxidative at pH 3 in Citrem-stabilized emulsions...

Adsorption at the biocompatible α-pinene-water interface and emulsifying properties of two eco-friendly surfactants.

Science.gov (United States)

Trujillo-Cayado, Luis Alfonso; Ramírez, Pablo; Alfaro, María Carmen; Ruíz, Manuela; Muñoz, José

2014-10-01

In this contribution, we provide an accurate characterization at the α-pinene/water interface of two commercial polyoxytheylene glycerol ester surfactants which differ in the number of ethylene oxide (EO) groups, comprising a systematic analysis of interfacial pressure isotherms, dynamic curves, interfacial rheology and emulsifying properties. Polyoxyethylene glycerol esters derived from cocoa oil are non-ionic surfactants obtained from a renewable source which fulfill the environmental and toxicological requirements to be used as eco-friendly emulsifying agents. α-Pinene is a renewable biosolvent completely insoluble in water, which could find numerous applications. Interfacial rheology and equilibrium interfacial pressure data fitted a rigorous reorientation model that assumes that the surfactant molecules, when adsorbed at the interface, can acquire two orientations. The surfactant with the highest number of EO groups (Levenol C201) turned out to be more surface active at the α-pinene/water interface. In addition, the surfactant with the lowest number of EO groups (Levenol H&B) is solubilized into the adjacent oil phase. Slightly concentrated α-pinene emulsions were obtained using both surfactants. Nevertheless, more stable α-pinene emulsions with smaller droplet sizes and lower polidispersity were obtained when Levenol C201 was used as emulsifier instead of Levenol H&B. The systematic characterization presented in this work provides important new findings on the interfacial and emulsifying properties of polyoxytheylene glycerol ester surfactants, which can be applied in the rational development of new biocompatible products. Copyright © 2014 Elsevier B.V. All rights reserved.

Produção de cerâmicas celulares por emulsão seguida de gelificação Production of cellular ceramics by gel casting ceramic emulsions

Directory of Open Access Journals (Sweden)

E. de Sousa

2011-03-01

Full Text Available As cerâmicas celulares têm sido produzidas por diferentes métodos, resultando em uma ampla faixa de estruturas e propriedades. Este trabalho descreve uma nova rota para a produção de cerâmicas celulares, a qual se baseia na gelificação de emulsões constituídas de suspensões cerâmicas aquosas contendo monômeros orgânicos solúveis em água e uma fase líquida apolar emulsificada (querosene. Os efeitos do teor de sólidos e da fração de querosene nas propriedades reológicas das emulsões foram avaliados. A estrutura celular foi analisada por microscopia eletrônica de varredura e revelou poros isolados nas amostras de baixa porosidade, os quais mudaram para uma rede interconectada de poros com o aumento da porosidade. Compressão diametral foi usada para avaliar a resistência mecânica das amostras sinterizadas, a qual variou entre 2,0 e 48 MPa, dependendo da porosidade.Cellular ceramics have been produced by several methods, resulting in a wide range of structures and properties. This work describes a novel route to produce cellular ceramics based on the gel casting of emulsions consisting of an aqueous ceramic suspension containing water-soluble organic monomers and an emulsified insoluble liquid phase (kerosene. The effects of solids loading and kerosene content on the rheological properties of emulsions were evaluated. SEM of the cellular structure revealed isolated pores for samples with low porosity, which changed to an interconnected network of pores as the porosity increased. Diametrical compression was used to evaluate the strength of sintered samples, which varied in the range of 2.0 and 48 MPa, depending on the porosity.

Automatic Generation of Machine Emulators: Efficient Synthesis of Robust Virtual Machines for Legacy Software Migration

DEFF Research Database (Denmark)

Franz, Michael; Gal, Andreas; Probst, Christian

2006-01-01

As older mainframe architectures become obsolete, the corresponding le- gacy software is increasingly executed via platform emulators running on top of more modern commodity hardware. These emulators are virtual machines that often include a combination of interpreters and just-in-time compilers....... Implementing interpreters and compilers for each combination of emulated and target platform independently of each other is a redundant and error-prone task. We describe an alternative approach that automatically synthesizes specialized virtual-machine interpreters and just-in-time compilers, which...... then execute on top of an existing software portability platform such as Java. The result is a considerably reduced implementation effort....

Copy of Using Emulation and Simulation to Understand the Large-Scale Behavior of the Internet.

Energy Technology Data Exchange (ETDEWEB)

Adalsteinsson, Helgi; Armstrong, Robert C.; Chiang, Ken; Gentile, Ann C.; Lloyd, Levi; Minnich, Ronald G.; Vanderveen, Keith; Van Randwyk, Jamie A; Rudish, Don W.

2008-10-01

We report on the work done in the late-start LDRDUsing Emulation and Simulation toUnderstand the Large-Scale Behavior of the Internet. We describe the creation of a researchplatform that emulates many thousands of machines to be used for the study of large-scale inter-net behavior. We describe a proof-of-concept simple attack we performed in this environment.We describe the successful capture of a Storm bot and, from the study of the bot and furtherliterature search, establish large-scale aspects we seek to understand via emulation of Storm onour research platform in possible follow-on work. Finally, we discuss possible future work.3

Environment Emulation For Wsn Testbed

Directory of Open Access Journals (Sweden)

Radosław Kapłoniak

2012-01-01

Full Text Available The development of applications for wireless sensor networks is a challenging task. For this reason, several testbed platforms have been created. They simplify the manageability of nodes by offering easy ways of programming and debugging sensor nodes. These platforms, sometimes composed of dozens of sensors, provide a convenient way for carrying out research on medium access control and data exchange between nodes. In this article, we propose the extension of the WSN testbed, which could be used for evaluating and testing the functionality of sensor networks applications by emulating a real-world environment.

Characterization of E 471 food emulsifiers by high-performance thin-layer chromatography-fluorescence detection.

Science.gov (United States)

Oellig, Claudia; Brändle, Klara; Schwack, Wolfgang

2018-07-13

Mono- and diacylglycerol (MAG and DAG) emulsifiers, also known as food additive E 471, are widely used to adjust techno-functional properties in various foods. Besides MAGs and DAGs, E 471 emulsifiers additionally comprise different amounts of triacylglycerols (TAGs) and free fatty acids (FFAs). MAGs, DAGs, TAGs and FFAs are generally determined by high-performance liquid chromatography (HPLC) or gas chromatography (GC) coupled to mass selective detection, analyzing the individual representatives of the lipid classes. In this work we present a rapid and sensitive method for the determination of MAGs, DAGs, TAGs and FFAs in E 471 emulsifiers by high-performance thin-layer chromatography with fluorescence detection (HPTLC-FLD), including a response factor system for quantitation. Samples were simply dissolved and diluted with t-butyl methyl ether before a two-fold development was performed on primuline pre-impregnated LiChrospher silica gel plates with diethyl ether and n-pentane/n-hexane/diethyl ether (52:20:28, v/v/v) as the mobile phases to 18 and 75 mm, respectively. For quantitation, the plate was scanned in the fluorescence mode at UV 366/>400 nm, when the cumulative signal for each lipid class was used. Calibration was done with 1,2-distearin and amounts of lipid classes were calculated with response factors and expressed as monostearin, distearin, tristearin and stearic acid. Limits of detection and quantitation were 1 and 4 ng/zone, respectively, for 1,2-distearin. Thus, the HPTLC-FLD approach represents a simple, rapid and convenient screening alternative to HPLC and GC analysis of the individual compounds. Visual detection additionally enables an easy characterization and the direct comparison of emulsifiers through the lipid class pattern, when utilized as a fingerprint. Copyright © 2018 Elsevier B.V. All rights reserved.

Effect of Different Combinations of Gums and Emulsifiers on the Quality of Bread

International Nuclear Information System (INIS)

Haider, M. R.; Din, G. M. U.; Mehmood, A.; Hussain, A.; Nasir, M. U.

2016-01-01

A project was designed to evaluate the effect of different combinations of emulsifiers and gums on the quality of bread. Wheat variety AARI-11 was milled to get straight grade flour and mixed with the Emulsifiers (DMG and DATEM) and Gums (G.G and CMC) in a quantity of (0.3- 0.6 %). Both, straight grade flour as well as treated flour (combination with gums and emulsifiers) were subjected to proximate and rheological analysis. Results of the rheological study showed a significant change in water absorption, dough development time, dough stability time and dough viscosity i.e. W/A 61.33-62.93%, D.D.T 3.9-4.8 min, D.S.T 7-9.1 min and 818.33-950.00 BU, respectively. Breads prepared with both flours were also studied for their sensory attributes during storage after the interval of 24 h. The highest score was awarded to T1 (0.3% DATEM and 0.5% guar gum) on the bases of its excellent external attributes (colour of crust, volume, symmetry of form, evenness of bake and crust character) and internal characteristics (aroma, grain, texture, taste, mastication and colour of crumb). After the sensory and physicochemical analyses, it is concluded that with the addition of DATEM (0.3%) and guar gum (0.5%) resulted in good quality of bread. (author)

Study on FPGA-Based Emulator for the Diagnosis of Gradual Degradation in Reciprocating Pump

Energy Technology Data Exchange (ETDEWEB)

Lim, Sang Sun; Kim, Wooshik [Sejong Univ., Seoul (Korea, Republic of); Kim, Tae Yun; Chai, Jang Bom [Ajou Univ., Suwon (Korea, Republic of)

2017-01-15

The purpose of this study is to develop a method for diagnosing the degree of gradual degradation of a reciprocating pump caused by continuous use as a water supply pump in a nuclear power plant. Normally, the progress of such degradation is too slow to be noticed. Hence, it is difficult to determine the degree of degradation using the existing diagnostic methods. In this paper, we propose a new method by which the normal state and the degraded state of the pump can be differentiated, so that the degree of degradation can be identified. First, an emulator was developed using FPGA by providing the parameters of the pump under normal state, so that the emulator generates the information of the pump in the healthy state. Then, by comparing this information with the parameters received from various output sensors of the emulator during the current state, it is possible to identify and measure the degree of gradual degradation. This paper presents some of the results obtained during the development process, and results that show how the emulator operates, by comparing the data collected from an actual pump.

Evaluation of glycerol derivative as emulsifier for oil based drilling fluids; Avaliacao de derivados de glicerina como emulsificante para fluidos de perfuracao de base oleo

Energy Technology Data Exchange (ETDEWEB)

Andrade, Susan A. [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil). Escola de Quimica; Cavalcanti, Milena Y.; Rodrigues Junior, Jorge; Lachter, Elizabeth R.; Nascimento, Regina Sandra V. [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil). Inst. de Quimica

2008-07-01

In view of the growing search for new applications for the surplus glycerine of biodiesel production, the use of a glycerine derivative as emulsifier in oil based muds is proposed in this work. Glycerine monooleate was synthesized through esterification reaction, and characterized by NMR{sup 13}C. Its applicability as emulsifier was verified through electric stability tests performed on inverted phase drilling fluids. The obtained results were compared with two formulations containing different emulsifiers (sorbitol monooleate and trimethylolpropane monooleate). It was also evaluated the rheological properties of the formulated fluids through standard tests. It was verified that the fluid that contained the glycerine derivative showed considerably better electric stability results than the other systems. It also presented rheological properties similar to the ones shown by the system that contained the commercial emulsifier (sorbitol monooleate). Thus, it was found that glycerine monooleate is a potential substitute to the currently emulsifiers (author)

Performance tests of a power-electronics converter for multi-megawatt wind turbines using a grid emulator

International Nuclear Information System (INIS)

Averous, Nurhan Rizqy; Berthold, Anica; Monti, Antonello; De Doncker, Rik W.; Schneider, Alexander; Schwimmbeck, Franz

2016-01-01

A vast increase of wind turbines (WT) contribution in the modern electrical grids have led to the development of grid connection requirements. In contrast to the conventional test method, testing power-electronics converters for WT using a grid emulator at Center for Wind Power Drives (CWD) RWTH Aachen University offers more flexibility for conducting test scenarios. Further analysis on the performance of the device under test (DUT) is however required when testing with grid emulator since the characteristic of the grid emulator might influence the performance of the DUT. This paper focuses on the performance analysis of the DUT when tested using grid emulator. Beside the issue regarding the current harmonics, the performance during Fault Ride-Through (FRT) is discussed in detail. A power hardware in the loop setup is an attractive solution to conduct a comprehensive study on the interaction between the power-electronics converters and the electrical grids. (paper)

Performance tests of a power-electronics converter for multi-megawatt wind turbines using a grid emulator

Science.gov (United States)

Rizqy Averous, Nurhan; Berthold, Anica; Schneider, Alexander; Schwimmbeck, Franz; Monti, Antonello; De Doncker, Rik W.

2016-09-01

A vast increase of wind turbines (WT) contribution in the modern electrical grids have led to the development of grid connection requirements. In contrast to the conventional test method, testing power-electronics converters for WT using a grid emulator at Center for Wind Power Drives (CWD) RWTH Aachen University offers more flexibility for conducting test scenarios. Further analysis on the performance of the device under test (DUT) is however required when testing with grid emulator since the characteristic of the grid emulator might influence the performance of the DUT. This paper focuses on the performance analysis of the DUT when tested using grid emulator. Beside the issue regarding the current harmonics, the performance during Fault Ride-Through (FRT) is discussed in detail. A power hardware in the loop setup is an attractive solution to conduct a comprehensive study on the interaction between the power-electronics converters and the electrical grids.

Effects of rice bran on sensory and physico-chemical properties of emulsified pork meatballs.

Science.gov (United States)

Huang, S C; Shiau, C Y; Liu, T E; Chu, C L; Hwang, D F

2005-08-01

Four kinds of bran, which are milled from important rice cultivators in Taiwan, have high contents of dietary fiber, fat and protein. The use of rice bran in Kung-wan, an emulsified pork meatball, was investigated. It was found that protein and fat contents, and white index of meatballs decreased as the amount of bran increased. A texture profile analysis (TPA) also indicated the hardness, gumminess and chewiness of the Kung-wan decreased. The sensory scores of taste, texture and overall acceptability of meatballs with less than 10% added bran showed no significant difference from those for meatballs without bran. However, the added amount of 15% enriched meatballs resulted in inferior sensory scores. The bran's particle size profoundly affected the sensory and physico-chemical properties of the meat products. Meatballs enriched with smaller bran particles possessed higher TPA indices and sensory scores than those added with larger ones. No significant differences in proximate composition, cooking yield, color and sensory quality were found among emulsified meatballs enriched with four different kinds of bran. Conclusively, the suitable amount of rice bran that should be added to emulsified pork meatballs was less than 10% and a smaller particle size would result in better quality.

Diesel engine performance and emission evaluation using emulsified fuels stabilized by conventional and gemini surfactants

Energy Technology Data Exchange (ETDEWEB)

M. Nadeem; C. Rangkuti; K. Anuar; M.R.U. Haq; I.B. Tan; S.S. Shah [Universiti Teknologi PETRONAS, Bandar Seri Iskandar (Malaysia)

2006-10-15

Diesel engines exhausting gaseous emission and particulate matter have long been regarded as one of the major air pollution sources, particularly in metropolitan areas, and have been a source of serious public concern for a long time. The emulsification method is not only motivated by cost reduction but is also one of the potentially effective techniques to reduce exhaust emission from diesel engines. Water/diesel (W/D) emulsified formulations are reported to reduce the emissions of NOx, SOx, CO and particulate matter (PM) without compensating the engine's performance. Emulsion fuels with varying contents of water and diesel were prepared and stabilized by conventional and gemini surfactant, respectively. Surfactant's dosage, emulsification time, stirring intensity, emulsifying temperature and mixing time have been reported. Diesel engine performance and exhaust emission was also measured and analyzed with these indigenously prepared emulsified fuels. The obtained experimental results indicate that the emulsions stabilized by gemini surfactant have much finer and better-distributed water droplets as compared to those stabilized by conventional surfactant. A comparative study involving torque, engine brake mean effective pressure (BMEP), specific fuel consumption (SFC), particulate matter (PM), NOx and CO emissions is also reported for neat diesel and emulsified formulations. It was found that there was an insignificant reduction in engine's efficiency but on the other hand there are significant benefits associated with the incorporation of water contents in diesel regarding environmental hazards. The biggest reduction in PM, NOx, CO and SOx emission was achieved by the emulsion stabilized by gemini surfactant containing 15% water contents. 34 refs., 11 figs., 1 tab.

Development of a Photovoltaic Array Emulator System in Real Time Considering Climatic Conditions Variations

Directory of Open Access Journals (Sweden)

Camilo E. Ardila-Franco

2013-11-01

Full Text Available This paper presents the development of an emulator that has the ability to replicate, in real time, the behavior of photovoltaic panels (PV arrays considering different conditions of irradiation and temperature for each one. The emulator consists of a data acquisition card, a programmable source and a computer. It is based on the bypass diode model that provides a better approximation to real operating conditions. The solution is computed by a simplified equation that uses the Lambert W function, which reduces the computation time. After that, it generates a solution table of values of current as a function of voltage on terminals, temperature and irradiation. Real-time emulation is performed by means of a search algorithm in the solutions table of the closest value to the voltage imposed on the terminals.

Emulating weak localization using a solid-state quantum circuit.

Science.gov (United States)

Chen, Yu; Roushan, P; Sank, D; Neill, C; Lucero, Erik; Mariantoni, Matteo; Barends, R; Chiaro, B; Kelly, J; Megrant, A; Mutus, J Y; O'Malley, P J J; Vainsencher, A; Wenner, J; White, T C; Yin, Yi; Cleland, A N; Martinis, John M

2014-10-14

Quantum interference is one of the most fundamental physical effects found in nature. Recent advances in quantum computing now employ interference as a fundamental resource for computation and control. Quantum interference also lies at the heart of sophisticated condensed matter phenomena such as Anderson localization, phenomena that are difficult to reproduce in numerical simulations. Here, employing a multiple-element superconducting quantum circuit, with which we manipulate a single microwave photon, we demonstrate that we can emulate the basic effects of weak localization. By engineering the control sequence, we are able to reproduce the well-known negative magnetoresistance of weak localization as well as its temperature dependence. Furthermore, we can use our circuit to continuously tune the level of disorder, a parameter that is not readily accessible in mesoscopic systems. Demonstrating a high level of control, our experiment shows the potential for employing superconducting quantum circuits as emulators for complex quantum phenomena.

Hardware emulation of Memristor based Ternary Content Addressable Memory

KAUST Repository

Bahloul, Mohamed A.

2017-12-13

MTCAM (Memristor Ternary Content Addressable Memory) is a special purpose storage medium in which data could be retrieved based on the stored content. Using Memristors as the main storage element provides the potential of achieving higher density and more efficient solutions than conventional methods. A key missing item in the validation of such approaches is the wide spread availability of hardware emulation platforms that can provide reliable and repeatable performance statistics. In this paper, we present a hardware MTCAM emulation based on 2-Transistors-2Memristors (2T2M) bit-cell. It builds on a bipolar memristor model with storing and fetching capabilities based on the actual current-voltage behaviour. The proposed design offers a flexible verification environment with quick design revisions, high execution speeds and powerful debugging techniques. The proposed design is modeled using VHDL and prototyped on Xilinx Virtex® FPGA.

Hardware emulation of Memristor based Ternary Content Addressable Memory

KAUST Repository

Bahloul, Mohamed A.; Naous, Rawan; Masmoudi, M.

2017-01-01

MTCAM (Memristor Ternary Content Addressable Memory) is a special purpose storage medium in which data could be retrieved based on the stored content. Using Memristors as the main storage element provides the potential of achieving higher density and more efficient solutions than conventional methods. A key missing item in the validation of such approaches is the wide spread availability of hardware emulation platforms that can provide reliable and repeatable performance statistics. In this paper, we present a hardware MTCAM emulation based on 2-Transistors-2Memristors (2T2M) bit-cell. It builds on a bipolar memristor model with storing and fetching capabilities based on the actual current-voltage behaviour. The proposed design offers a flexible verification environment with quick design revisions, high execution speeds and powerful debugging techniques. The proposed design is modeled using VHDL and prototyped on Xilinx Virtex® FPGA.

PROPRIEDADES EMULSIONANTES E SOLUBILIDADE DA CASEÍNA BOVINA: 2. EFEITO DA ADIÇÃO DE NaCl EMULSIFYING PROPERTIES AND SOLUBILITY OF CASEIN: 2. EFFECTS OF THE NaCl ADDITION

Directory of Open Access Journals (Sweden)

Ângela Jardim DUARTE

1998-08-01

Full Text Available O efeito da adição de NaCl sobre algumas propriedades funcionais da caseína e de seus hidrolisados trípticos, foi estudado em dois valores de pH (4,0 e 5,0. Para tal, foi adicionado um teor de 0,02M do sal às soluções-tampão empregadas no preparo das amostras. Foram determinadas a solubilidade protéica, a capacidade emulsificante (EC, o índice de atividade emulsificante (EAI e a estabilidade das emulsões (ES, e o raio médio dos glóbulos de gordura (R foi calculado. Os resultados obtidos indicaram que, nos dois valores de pH estudados, a adição de NaCl levou a um aumento significativo da solubilidade e da EC da caseína e de todos os hidrolisados trípticos. Por outro lado, diminuiu os valores de EAI da caseína e elevou os dos hidrolisados, tendo sido observado o oposto para o tamanho dos glóbulos de gordura. Com relação à ES, a da caseína apresentou ligeiro aumento no pH 5,0, enquanto que apenas alguns hidrolisados trípticos tiveram a sua ES elevada em pH 4,0 ou 5,0.The effect of the NaCl addition on the emulsifying properties of casein and tryptic casein hydrolysates was studied in two pH values (4,0 e 5,0. A 0.02 M concentration of salt was added to the buffer solutions used for preparing the samples. The protein solubility, the emulsifying capacity (EC, the emulsifying activity index (EAI and the emulsion stability (ES were determined. The mean radius (R of fat droplets was also calculated. The results showed that the addition of NaCl increased the solubility and the EC of casein and casein hydrolysates, in both pH values. However, this salt addition reduced the EAI of casein and increased that of the hydrolysates.The opposite was observed relating to the R of fat droplets. Regarding the ES, that of casein presented little increase in pH 5.0, and the same result was obtained for only some hydrolysates in pH 5.0 or 4.0.

Quality characteristics of egg-reduced pound cakes following WPI and emulsifier incorporation

NARCIS (Netherlands)

Paraskevopoulou, A.; Donsouzi, S.; Nikiforidis, C.V.; Kiosseoglou, V.

2015-01-01

The effect of partial (50 wt%) or total liquid egg replacement by whey proteins in combination with emulsifiers, i.e. hydroxypropylmethylcellulose (HPMC) and sodium stearoyl-2-lactylate (SSL), on the quality of pound cakes was investigated. Cakes containing whey protein isolate (WPI) solutions of

The Effect of Emulsifier and Hydrocolloid on Baking Expansion and Texture of Bread from Modified Cassava

Directory of Open Access Journals (Sweden)

Pudjihastuti Isti

2018-01-01

Full Text Available Indonesia has a very abundant cassava that can be used instead of wheat. Bread made from cassava is safe for celiac sufferers, in which cannot tolerate a protein called gluten found in wheat flour. However, bread from cassava has the disadvantage that it cannot inflate perfectly. Our research goal is to study the effect of emulsifier and hydrocolloid concentration as modifying agents on baking expansion and bread texture (hardness. The test level hedonic preference for bread products results from modified tapioca is also necessary to know the level of customer satisfaction. This study were conducted by three main stages, modification of cassava, baking process, and analyses. Modification of cassava starch was applied using combination of lactic acid solution and ultra violet (UV irradiation. Emulsifier (DATEM and hydrocolloid (xanthan gum were used in baking process. The addition of emulsifier and hydrocolloid can improve baking expansion. The addition of 7% emulsifiers on modified cassava can increase the volume of bread, taste, and texture so it can give greater satisfaction to consumers. Hydrocolloid can replace the function of gluten so the bread can inflate perfectly. The optimal composition of modified cassava in bread making is 25% of modified cassava and 75% of wheat flour. The low value of texture (hardness on bread made from modified cassava indicated a better performance in comparison with native cassava. Baking expansion and texture of the bread is influenced by the modification process. Furthermore, the comprehensive and optimum studies of modification need to be investigated.

The coyote universe extended: Precision emulation of the matter power spectrum

International Nuclear Information System (INIS)

Heitmann, Katrin; Kwan, Juliana; Habib, Salman; Lawrence, Earl; Higdon, David

2014-01-01

Modern sky surveys are returning precision measurements of cosmological statistics such as weak lensing shear correlations, the distribution of galaxies, and cluster abundance. To fully exploit these observations, theorists must provide predictions that are at least as accurate as the measurements, as well as robust estimates of systematic errors that are inherent to the modeling process. In the nonlinear regime of structure formation, this challenge can only be overcome by developing a large-scale, multi-physics simulation capability covering a range of cosmological models and astrophysical processes. As a first step to achieving this goal, we have recently developed a prediction scheme for the matter power spectrum (a so-called emulator), accurate at the 1% level out to k ∼ 1 Mpc –1 and z = 1 for wCDM cosmologies based on a set of high-accuracy N-body simulations. It is highly desirable to increase the range in both redshift and wavenumber and to extend the reach in cosmological parameter space. To make progress in this direction, while minimizing computational cost, we present a strategy that maximally reuses the original simulations. We demonstrate improvement over the original spatial dynamic range by an order of magnitude, reaching k ∼ 10 h Mpc –1 , a four-fold increase in redshift coverage, to z = 4, and now include the Hubble parameter as a new independent variable. To further the range in k and z, a new set of nested simulations run at modest cost is added to the original set. The extension in h is performed by including perturbation theory results within a multi-scale procedure for building the emulator. This economical methodology still gives excellent error control, ∼5% near the edges of the domain of applicability of the emulator. A public domain code for the new emulator is released as part of the work presented in this paper.

STABILITY OF EMULSIFIER-FREE EMULSION COPOLYMERIZATION OF METHYL METHACRYLATE/ BUTYL ACRYLATE/SODIUM MONO(ETHYL POLYOXYETHYLENE) MALEATE

Institute of Scientific and Technical Information of China (English)

Mao-gen Zhang; Zhi-xue Weng; Zhi-ming Huang; Zu-ren Pan

1999-01-01

A series of new water-soluble bifunctional comonomers having both carboxyl and alkyl polyoxyethylene groups, such as sodium mono(ethyl polyoxyethylene) maleate (ZE series) with various molecular weights of polyoxyethylene ethyl ether, were synthesized and characterized. The effects of the structural factor, the amount and feeding mode of the comonomers, the initiator concentration and polymerization temperature on the stability of emulsifier-free emulsion copolymerization of methyl methacrylate (MMA) and butyl acrylate (BA) in the presence of a small amount of ZE with potassium persulfate as initiator were investigated. Stable, almost monodispersed MMA/BA/ZE emulsifier-free latex particles were prepared.

Influence of different emulsifiers on characteristics of eggless cake containing soy milk: Modeling of physical and sensory properties by mixture experimental design.

Science.gov (United States)

Rahmati, Nazanin Fatemeh; Mazaheri Tehrani, Mostafa

2014-09-01

Emulsifiers of different structures and functionalities are important ingredients usually used in baking cakes with satisfactory properties. In this study, three emulsifiers including distilled glycerol mono stearate (DGMS), lecithin and sorbitan mono stearate (SMS) were used to bake seven eggless cakes containing soy milk and optimization was performed by using mixture experimental design to produce an eggless cake sample with optimized properties. Physical properties of cake batters (viscosity, specific gravity and stability), cake quality parameters (moisture loss, density, specific volume, volume index, contour, symmetry, color and texture) and sensory attributes of eggless cakes were analyzed to investigate functional potential of the emulsifiers and results were compared with those of control cake containing egg. Almost in all cases emulsifiers, compared to the control cake, changed properties of eggless cakes significantly. Regarding models of different response variables (except for some properties) and their high R(2) (99.51-100), it could be concluded that models obtained by mixture design were significantly fitted for the studied responses.

A Smart Home Development Tool combining Simulation, Emulation and Real-World IoT

DEFF Research Database (Denmark)

Lynggaard, Per

Intelligent smart homes will offer context-aware, personalized and adaptive services to users. These services range from simple remote control to fully automated / autonomous actions based on user context and adaptive behaviour. However, in science it is difficult to study smart homes...... and their embedded smart objects, because laboratory environments are costly and time consuming to create. This paper proposes a simulator with built-in emulator capabilities. It integrates smart home simulation and emulation capabilities into one device. In this way, smart home implementation models exist either...

Stabilization of heavy oil-water emulsions using a bio/chemical emulsifier mixture

Energy Technology Data Exchange (ETDEWEB)

Farahbakhsh, A.; Taghizadeh, M.; Movagharnejad, K. [Chemical Engineering Department, Babol University of Technology, Babol (Iran, Islamic Republic of); Yakhchali, B. [National Institute of Genetic Engineering and Biotechnology, Tehran (Iran, Islamic Republic of)

2011-11-15

In this study, the viscosity reduction of heavy oil has been investigated through the formation of oil-water emulsion using a bio/chemical emulsifier mixture. Four bioemulsifiers from indigenous Rhodococcus ergthropolis and Bacillus licheniformis strains were used to stabilize a highly-viscous oil-in-water emulsion. The Taguchi method with an L{sub 9} orthogonal array design was used to investigate the effect of various control factors on the formation of the oil/water emulsions. An emulsion with lowest viscosity was formed using ACO4 strain. The substantial stability of the oil-in-water emulsion allows the heavy oil to be transported practically over long distances or remain stationary for a considerable period of time prior to utilization. As the result of Taguchi analysis, the temperature and concentration of the emulsifier had a significant influence on viscosity reduction of the emulsion. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Rapid testing and identification of actuator using dSPACE real-time emulator

Science.gov (United States)

Xie, Daocheng; Wang, Zhongwei; Zeng, Qinghua

2011-10-01

To solve the problem of model identification of actuator in control system design of aerocraft, testing system based on dSPACE emulator is established, sending testing signal and receiving feedback voltage are realized using dSPACE interactive cards, communication between signal generating equipment and feedback voltage acquisition equipment is synchronized. This paper introduces the hardware architecture and key technologies of the simulation system. Constructing, downloading and calculating of the testing model is finished using dSPACE emulator, D/A transfer of testing signal is realized using DS2103 card, DS2002 card transfer the feedback voltage to digital value. Filtering module is added to the signal acquisition, for reduction of noise interference in the A/D channel. Precision of time and voltage is improved by setting acquisition period 1ms. The data gathered is recorded and displayed with Controldesk tools. The response of four actuators under different frequency are tested, frequency-domain analysis is done using least square method, the model of actuator is identified, simulation data fits well with real response of the actuator. The testing system created with dSPACE emulator satisfies the rapid testing and identification of actuator.

Novel Modified Elman Neural Network Control for PMSG System Based on Wind Turbine Emulator

OpenAIRE

Lin, Chih-Hong

2013-01-01

The novel modified Elman neural network (NN) controlled permanent magnet synchronous generator (PMSG) system, which is directly driven by a permanent magnet synchronous motor (PMSM) based on wind turbine emulator, is proposed to control output of rectifier (AC/DC power converter) and inverter (DC/AC power converter) in this study. First, a closed loop PMSM drive control based on wind turbine emulator is designed to generate power for the PMSG system according to different wind speeds. Then, t...

Modeling, Analysis and Control of Different DC-DC Converter Topologies for Photo Voltaic Emulator

Directory of Open Access Journals (Sweden)

Mohammad Tauquir Iqbal

2016-05-01

Full Text Available This paper presents the modeling, analysis and control of different DC-DC converter topologies to emulate the photovoltaic (PV system. A PV emulator is basically a DC-DC converter having same electrical characteristics that of solar PV panel.  The emulator helps to achieve real characteristics of PV system in a better way in an environment where using actual PV systems can produce inconsistent results due to variation in weather conditions. The paper describes different types of DC-DC converters like buck, Resonant and Quasi Resonant Converter. The complete system is modelled in MATLAB® Simulink SimPowerSystem software package. The Simulation results obtained from the MATLAB® Simulink SimPowerSystem software package for different topologies under steady and dynamic conditions are analyzed and presented. An evaluation table is also presented at the end of the paper, presenting the effectiveness of each topology.

Performance Guaranteed Inertia Emulation forDiesel-Wind System Feed Microgrid via ModelReference Control

Energy Technology Data Exchange (ETDEWEB)

Melin, Alexander M. [ORNL; Zhang, Yichen [University of Tennessee, Knoxville (UTK), Department of Electrical Engineering and Computer Science; Djouadi, Seddik [University of Tennessee, Knoxville (UTK), Department of Electrical Engineering and Computer Science; Olama, Mohammed M. [ORNL

2017-04-01

In this paper, a model reference control based inertia emulation strategy is proposed. Desired inertia can be precisely emulated through this control strategy so that guaranteed performance is ensured. A typical frequency response model with parametrical inertia is set to be the reference model. A measurement at a specific location delivers the information of disturbance acting on the diesel-wind system to the referencemodel. The objective is for the speed of the diesel-wind system to track the reference model. Since active power variation is dominantly governed by mechanical dynamics and modes, only mechanical dynamics and states, i.e., a swing-engine-governor system plus a reduced-order wind turbine generator, are involved in the feedback control design. The controller is implemented in a three-phase diesel-wind system feed microgrid. The results show exact synthetic inertia is emulated, leading to guaranteed performance and safety bounds.

Performance emulation and parameter estimation for nonlinear fibre-optic links

DEFF Research Database (Denmark)

Piels, Molly; Porto da Silva, Edson; Zibar, Darko

2016-01-01

Fibre-optic communication systems, especially when operating in the nonlinear regime, generally do not perform exactly as theory would predict. A number of methods for data-based evaluation of nonlinear fibre-optic link parameters, both for accurate performance emulation and optimization...

Development of Ethernet emulation driver for reflective memory

International Nuclear Information System (INIS)

Seo, Seong-Heon

2010-01-01

Reflective memory (RFM) is adopted as a real time network in the KSTAR plasma control system (PCS). Since the data uploaded from any computer are automatically shared among all the computers on the RFM network, the design of a distributed control system based on RFM is easily implemented through the management of memory mapping. The data providers and consumers are logically well seperated so that, if memory mapping information is given, a new control unit can be added without any modification to the existing system except connecting a new RFM module through an optical cable. The KSTAR PCS is also connected with the Ethernet in addition to the RFM because the RFM does not support the Transmission Control Protocol/Internet Protocol (TCP/IP) and many network services of the operating system such as the Network File System (NFS) and the Secure Shell (SSH) are based on the TCP/IP. Therefore we developed an Ethernet emulation driver for the RFM to eliminate the need for a separate Ethernet network. The driver was tested on the Linux kernel 2.6.31. The algorithm of the emulation driver is explained and the experimental setup is presented.

Bayesian Sensitivity Analysis of a Cardiac Cell Model Using a Gaussian Process Emulator

Science.gov (United States)

Chang, Eugene T Y; Strong, Mark; Clayton, Richard H

2015-01-01

Models of electrical activity in cardiac cells have become important research tools as they can provide a quantitative description of detailed and integrative physiology. However, cardiac cell models have many parameters, and how uncertainties in these parameters affect the model output is difficult to assess without undertaking large numbers of model runs. In this study we show that a surrogate statistical model of a cardiac cell model (the Luo-Rudy 1991 model) can be built using Gaussian process (GP) emulators. Using this approach we examined how eight outputs describing the action potential shape and action potential duration restitution depend on six inputs, which we selected to be the maximum conductances in the Luo-Rudy 1991 model. We found that the GP emulators could be fitted to a small number of model runs, and behaved as would be expected based on the underlying physiology that the model represents. We have shown that an emulator approach is a powerful tool for uncertainty and sensitivity analysis in cardiac cell models. PMID:26114610

DDM Workload Emulation

CERN Document Server

Vigne, R; The ATLAS collaboration; Garonne, V; Stewart, G; Barisits, M; Beermann, T; Lassnig, M; Serfon, C; Goossens, L; Nairz, A

2013-01-01

Rucio is the successor of the current Don Quijote 2 (DQ2) system for the distributed data management (DDM) system of the ATLAS experiment. The reasons for replacing DQ2 are manifold, but besides high maintenance costs and architectural limitations, scalability concerns are on top of the list. Current expectations are that the amount of data will be three to four times as it is today by the end of 2014. Further is the availability of more powerful computing resources pushing additional pressure on the DDM system as it increases the demands on data provisioning. Although DQ2 is capable of handling the current workload, it is already at its limits. To ensure that Rucio will be up to the expected workload, a way to emulate it is needed. To do so, first the current workload, observed in DQ2, must be understood in order to scale it up to future expectations. The paper discusses how selected core concepts are applied to the workload of the experiment and how knowledge about the current workload is derived from vario...

DDM Workload Emulation

CERN Document Server

Vigne, R; The ATLAS collaboration; Garonne, V; Stewart, G; Barisits, M; Beermann, T; Serfon, C; Goossens, L; Nairz, A

2014-01-01

Rucio is the successor of the current Don Quijote 2 (DQ2) system for the distributed data management (DDM) system of the ATLAS experiment. The reasons for replacing DQ2 are manifold, but besides high maintenance costs and architectural limitations, scalability concerns are on top of the list. Current expectations are that the amount of data will be three to four times as it is today by the end of 2014. Further is the availability of more powerful computing resources pushing additional pressure on the DDM system as it increases the demands on data provisioning. Although DQ2 is capable of handling the current workload, it is already at its limits. To ensure that Rucio will be up to the expected workload, a way to emulate it is needed. To do so, first the current workload, observed in DQ2, must be understood in order to scale it up to future expectations. The paper discusses how selected core concepts are applied to the workload of the experiment and how knowledge about the current workload is derived from vario...

Effects of Lipids and Emulsifiers on the Physicochemical and Sensory Properties of Cosmetic Emulsions Containing Vitamin E

Directory of Open Access Journals (Sweden)

Lucia Montenegro

2015-03-01

Full Text Available Sensory properties are fundamental in determining the success of a cosmetic product. In this work, we assessed the influence of different oils and emulsifiers on the physicochemical and sensory properties of anti-ageing cosmetic O/W emulsions containing vitamin E acetate as active ingredient. No clear correlation between physicochemical properties and sensory characteristics was evidenced. Sensorial evaluation of these formulations pointed out that the emulsifier systems affected the perceived oiliness and absorbency during application of the product, thus influencing its acceptance. These results suggest the need for more detailed studies on the physicochemical factors involved in determining the consumers’ acceptance.

Characteristic of sausages as influenced by partial replacement of pork back-fat using pre-emulsified soybean oil stabilized by fish proteins isolate

Directory of Open Access Journals (Sweden)

Nopparat Cheetangdee

2017-08-01

Full Text Available Substitution of animal fat with oils rich in n-3 is a feasible way to improve the nutritive value of comminuted meat product. The effect on the characteristics of sausages was investigated of partial replacement of porcine fat with soybean oil (SBO using a pre-emulsification technique. Fish protein isolate (FPI produced from yellow stripe trevally (Selaroides leptolepis was used as an emulsifier to prepare pre-emulsified SBO (preSBO, and its concentration effect (1%, 2% and 3%, w/v was observed in comparison with soy protein isolate (SPI. Substitution of porcine fat using preSBO enhanced the product stability. SPI exhibited better emulsifying ability than FPI. However, FPI was more effective at reinforcing the protein matrix of the sausages than SPI, as suggested by a lowered cooking loss and the restored textural attributes of the sausages formulated with FPI stabilized preSBO. The effective concentration of FPI to improve the product stability was 2%. This work suggested that FPI was promising in the preparation of emulsified meat products.

Oxidative stability of 70% fish oil‐in‐water emulsions: Impact of emulsifiers and pH

DEFF Research Database (Denmark)

Horn, Anna Frisenfeldt; Nielsen, Nina Skall; Andersen, Ulf

2011-01-01

The objective of this study was to evaluate the protective effects of five different emulsifiers on lipid oxidation in 70% fish oil‐in‐water emulsions to be used as delivery systems for long chain polyunsaturated omega‐3 fatty acids to foods. The emulsifiers were either phospholipid (PL) based......‐in‐water emulsions prepared with whey protein isolate, sodium caseinate, milk phospholipids, or soy lecithin. The emulsions can be used as delivery systems for fish oil to foods. However, only emulsions prepared with proteins at high pH offered advantages with respect to better oxidative stability during storage...... compared to neat fish oil. Thus, when fish oil is added to a food product in a delivery emulsion, the type of emulsion used should be carefully considered....

Antioxidative activity and emulsifying properties of cuttlefish skin gelatin modified by oxidised phenolic compounds

NARCIS (Netherlands)

Aewsiri, T.; Benjakul, S.; Visessanguan, W.; Eun, J.B.; Wierenga, P.A.; Gruppen, H.

2009-01-01

Antioxidative activity and emulsifying properties of cuttlefish skin gelatin modified by different oxidised phenolic compounds including caffeic acid, ferulic acid and tannic acid at different concentrations were investigated. Oxidised phenolic compounds were covalently attached to gelatin as

Simulation, measurement, and emulation of photovoltaic modules using high frequency and high power density power electronic circuits

Science.gov (United States)

Erkaya, Yunus

The number of solar photovoltaic (PV) installations is growing exponentially, and to improve the energy yield and the efficiency of PV systems, it is necessary to have correct methods for simulation, measurement, and emulation. PV systems can be simulated using PV models for different configurations and technologies of PV modules. Additionally, different environmental conditions of solar irradiance, temperature, and partial shading can be incorporated in the model to accurately simulate PV systems for any given condition. The electrical measurement of PV systems both prior to and after making electrical connections is important for attaining high efficiency and reliability. Measuring PV modules using a current-voltage (I-V) curve tracer allows the installer to know whether the PV modules are 100% operational. The installed modules can be properly matched to maximize performance. Once installed, the whole system needs to be characterized similarly to detect mismatches, partial shading, or installation damage before energizing the system. This will prevent any reliability issues from the onset and ensure the system efficiency will remain high. A capacitive load is implemented in making I-V curve measurements with the goal of minimizing the curve tracer volume and cost. Additionally, the increase of measurement resolution and accuracy is possible via the use of accurate voltage and current measurement methods and accurate PV models to translate the curves to standard testing conditions. A move from mechanical relays to solid-state MOSFETs improved system reliability while significantly reducing device volume and costs. Finally, emulating PV modules is necessary for testing electrical components of a PV system. PV emulation simplifies and standardizes the tests allowing for different irradiance, temperature and partial shading levels to be easily tested. Proper emulation of PV modules requires an accurate and mathematically simple PV model that incorporates all known

Synthesis and characterization of fluorinated polyacrylate latex emulsified with novel surfactants.

Science.gov (United States)

Zhang, Cuifeng; Xu, Tingting; Bao, Zhongbin; Chen, Lijun

2017-01-01

The fluorinated polyacrylate latex were successfully prepared with semi- continuous seeded emulsion polymerization of butyl acrylate (BA), methyl methacrylate (MMA) and hexafluorobutyl methacrylate (HFMA) which was initiated with potassium persulfate (KPS) initiator and emulsified with the novel mixed surfactants of sodium lauryl glutamate (SLG) and alkylphenol ethoxylates (OP-10). The structure of the resultant latex was confirmed by Fourier transform infrared spectroscopy (FTIR). The particle size of the latex was measured by Zetatrac dynamic light scattering detector. The film of latex was tested by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and contact angle (CA). The optimum conditions of preparing the novel fluorinated polyacrylate latex are optimized and the results are as follows: the amount of emulsifiers is 4.0%; mass ratio of SLG to OP-10 is 1:1, the amount of the initiator is 0.6%. The mass ratio of MMA to BA is 1:1 and the amount of HFMA is 7.0%. In this case, the conversion is high and the polymerization stability is good. In addition, the water resistance and thermal properties of the latex films were improved significantly in comparison with the film of the latex prepared without the fluorinated monomer.

Improvement of Emulsifying Properties of Wheat Gluten Hydrolysate λ-Carrageenan Conjugates

Directory of Open Access Journals (Sweden)

Jin-Shui Wang

2006-01-01

Full Text Available Gluten hydrolysate was prepared through limited enzymatic hydrolysis of wheat gluten resulting from the byproducts of wheat starch. The enzyme applied in the present study was Protamex. Response surface methodology was used to investigate the effects of pH, gluten hydrolysate (GHPλ-carrageenan (C ratio and reaction time on emulsifying properties of the GHP-C conjugate. The regression model for emulsion activity index (EAI was significant at p=0.001, while reaction time had a significant effect on EAI of the conjugate with regression coefficient of 4.25. The interactions of pH and GHP/ C ratio, and GHP/C ratio and reaction time significantly affected the EAI of the conjugate. Both the emulsifying property and nitrogen solubility index (NSI of GHP-C conjugate prepared under the optimal conditions increased more remarkably, compared to the control. The denaturation temperature of GHP-C conjugate obviously increased compared to wheat gluten. The addition of GHP-C conjugate had different effects on dough characteristics. Moreover, this conjugate can delay the increase in the bread crumb firmness during storage. It demonstrated that this conjugate couldimprove the dough characteristics and had anti-staling properties of bread.

The Influence of Emulsifier on Rheological and Sensory Properties of Cosmetic Lotions

Czech Academy of Sciences Publication Activity Database

Morávková, Tereza; Filip, Petr

2013-01-01

Roč. 2013, july (2013) ISSN 1687-6822 R&D Projects: GA ČR GA103/09/2066 Institutional research plan: CEZ:AV0Z20600510 Institutional support: RVO:67985874 Keywords : cosmetic lotions * emulsifiers * sensory assessments Subject RIV: BK - Fluid Dynamics Impact factor: 0.500, year: 2012 http://www.hindawi.com/journals/amse/2013/168503/

Engineered Multifunctional Fluorinated Film Based on Semicontinuous Emulsion Polymerization Using Polymerizable Quaternary Ammonium Emulsifiers

Directory of Open Access Journals (Sweden)

Hongzhu Liu

2018-01-01

Full Text Available Along with society’s progress, high-quality coatings are widely used. Although fluorinated polymers were successfully prepared by semicontinuous emulsion polymerization with surfactants, chlorotrifluoroethylene (CTFE, and acrylate monomers, the optimization collocation of surfactants still has room for improvement. The traditional emulsifiers are physically absorbed onto the surface of latex particles. The latex film generated by latex particles is unstable in water, which limits its application. Herein, a novel series of cationic quaternary ammonium polymerizable surfactant was selected because it can react with CTFE and acrylate monomers and can become a part of the polymers. We also studied the effects of emulsifier type on resultant emulsion properties. In addition, wonderful weatherability, water resistance, and antibacterial and antifouling of the multifunctional fluorinated films were observed, which would open up a bright future for coating industries.

Application of Emulsified Zero-Valent Iron to Marine Environments

Science.gov (United States)

Brooks, Kathleen B.; Quinn, Jacqueline W.; Clausen, Christian A.; Geiger, Cherie L.

2005-01-01

Contamination of marine waters and sediments with heavy metals and dense non-aqueous phase liquids (DNAPLs) including chlorinated solvents, pesticides and PCBs pose ecological and human health risks through the contaminant's potential bioaccumulation in fish, shellfish and avian populations. The contaminants enter marine environments through improper disposal techniques and storm water run-off. Current remediation technologies for application to marine environments include costly dredging and off-site treatment of the contaminated media. Emulsified zero-valent iron (EZVI) has been proven to effectively degrade dissolved-phase and DNAPL-phase contaminants in freshwater environments on both the laboratory and field-scale level. However, the application to marine environments is only just being explored. This paper discusses the potential use of EZVI in brackish and saltwater environments, with supporting laboratory data detailed. Laboratory studies were performed in 2005 to establish the effectiveness of EZVI to degrade trichloroethylene (TCE) in saltwater. Headspace vials were setup to determine the kinetic rate of TCE degradation using EZVI in seawater. The reaction vials were analyzed by Gas Chromatographic/Flame Ionization Detection (GC/FID) for ethene production after a 48 day period using a GC/FID Purge and Trap system. Analytical results showed that EZVI was very effective at degrading TCE. The reaction by-products (ethene, acetylene and ethane) were produced at 71% of the rate in seawater as in the fresh water controls. Additionally, iron within the EZVI particles was protected from oxidation of the corrosive seawater, allowing EZVI to perform in an environment where zero-valent iron alone could not compete. Laboratory studies were also performed to establish the effectiveness of emulsified zero-valent metal (EZVM) to remove dissolved-phase cadmium and lead found in seawater. EZVM is comprised of a combination of magnesium and iron metal surrounded by the

Emulsifying properties of maillard conjugates produced from sodium caseinate and locust bean gum

Directory of Open Access Journals (Sweden)

F. A. Perrechil

2014-06-01

Full Text Available Emulsifying properties of sodium caseinate -locust bean gum Maillard conjugates produced at different temperatures (54 - 96 ºC, protein/polysaccharide ratios (0.3 - 1.0 and reaction times (1 - 24 hours were evaluated. Conjugate formation was confirmed by formation of color and high molecular weight fractions and the decrease of the αs- and β-casein bands. The emulsions stabilized by Maillard conjugates showed good stability. The mean droplet diameter (d32 tended to decrease with the increase of incubation time and temperature, except at extreme conditions (24 hours and 90 ºC or 96 ºC when the partial degradation of the conjugates was probably favored, resulting in phase separation of emulsions. The emulsion viscosity decreased with the increase in the protein/polysaccharide ratio and with the degradation of the conjugates. The conditions used in the experimental design made the optimization of the conjugate production viable, which showed greater emulsifier properties than the pure protein under acid conditions.

Study on degradation of nitrobenzene in groundwater using emulsified nano-zero-valent iron

Energy Technology Data Exchange (ETDEWEB)

Dong, Jun, E-mail: dongjun@jlu.edu.cn; Wen, Chunyu, E-mail: 13756014702@163.com; Liu, Dengfeng, E-mail: 862337789@qq.com [Jilin University, College of Environment and Resources (China); Zhang, Wenjing, E-mail: zhangwj@caep.org.cn [Chinese Academy for Environmental Planning (CAEP) (China); Li, Jintong, E-mail: 1535448369@qq.com; Jiang, Hanjie, E-mail: 1932639992@qq.com; Qin, Chongwei, E-mail: 476158689@qq.com; Hong, Mei, E-mail: hongmei@jlu.edu.cn [Jilin University, College of Environment and Resources (China)

2015-01-15

Emulsified nano-zero-valent iron (EZVI) is a modified form of bare nanoiron with improved transportability and targetability for the remediation of organic-solvents polluted soil and groundwater. In this work, EZVI (50–150 nm) was prepared by coating an emulsified vegetable oil membrane on the surface of Fe nanoparticles. EZVI was well-dispersed and less aggregation was observed. Batch experiments were conducted in anaerobic conditions to investigate the kinetics of nitrobenzene reduction by EZVI and the influences of oil concentration, initial iron content, and initial pH. Results indicated that the kinetics of nitrobenzene reduction by EZVI followed a pseudo-first-order kinetics. The observed rate constant of nitrobenzene is 0.0942 min{sup −1}. The oil concentration of 1 and 2 % tended to be preferred concentrations. The rate of nitrobenzene degradation and aniline formation increased with increasing iron content. The low pH is favorable to the nitrobenzene reduction by EZVI.

Effectiveness of a fading emulator in evaluating the performance of MIMO systems by comparison with a propagation test

DEFF Research Database (Denmark)

Yamamoto, Atsushi; Sakata, T.; Hayashi, T.

2010-01-01

This paper presents a MIMO spatial fading emulator, used to represent a street microcell environment. The fading emulator can reproduce a multipath radio propagation environment with either a uniform or non-uniform angular power spectrum (APS) in the horizontal plane. In this paper, we used...

Evaporation and Ignition Characteristics of Water Emulsified Diesel under Conventional and Low Temperature Combustion Conditions

Directory of Open Access Journals (Sweden)

Zhaowen Wang

2017-07-01

Full Text Available The combination of emulsified diesel and low temperature combustion (LTC technology has great potential in reducing engine emissions. A visualization study on the spray and combustion characteristics of water emulsified diesel was conducted experimentally in a constant volume chamber under conventional and LTC conditions. The effects of ambient temperature on the evaporation, ignition and combustion characteristics of water emulsified diesel were studied under cold, evaporating and combustion conditions. Experimental results showed that the ambient temperature had little effect on the spray structures, in terms of the liquid core length, the spray shape and the spray area. However, higher ambient temperature slightly reduced the Sauter Mean Diameter (SMD of the spray droplets. The auto-ignition delay time increased significantly with the decrease of the ambient temperature. The ignition process always occurred at the entrainment region near the front periphery of the liquid core. This entrainment region was evolved from the early injected fuel droplets which were heated and mixed by the continuous entrainment until the local temperature and equivalence ratio reached the ignition condition. The maximum value of integrated natural flame luminosity (INFL reduced by 60% when the ambient temperature dropped from 1000 to 800 K, indicating a significant decrease of the soot emissions could be achieved by LTC combustion mode than the conventional diesel engines.

Helix aspersa gelatin as an emulsifier and emulsion stabilizer: functional properties and effects on pancreatic lipolysis.

Science.gov (United States)

Zarai, Zied; Balti, Rafik; Sila, Assaâd; Ben Ali, Yassine; Gargouri, Youssef

2016-01-01

Emulsions are widely used in food and pharmaceutical applications for the encapsulation, solubilization, entrapment, and controlled delivery of active ingredients. In order to fulfill the increasing demand for clean label excipients, natural polymers could be used to replace the potentially irritative synthetic surfactants used in emulsion formulation. In the present study, we have studied the properties of oil-in-water emulsions prepared with land snail gelatin (LSG) as the sole emulsifying agent, extracted and described for the first time. LSG was evaluated in terms of proximate composition, oil and water holding capacity, emulsifying and foaming properties, color and amino acid composition. Emulsions of trioctanoylglycerol (TC8) and olive oil were made at different gelatin/oil ratios and changes in droplet-size distribution were determined. The superior emulsifying properties of LSG, the susceptibility of gelatin protein emulsions increasing flocculation on storage, and the coalescence of gelatin emulsions following centrifugation were demonstrated. Furthermore, the effect of LSG on the activity of turkey pancreatic lipase (TPL) was evaluated through the pH-stat methodology with TC8 and olive oil emulsions. The LSG affected the TPL activity in a concentration-dependent way. Our results showed that LSG, comparably to gum arabic, increases the pancreatic lipase activity and improves its stability at the oil-water interface.

THE INFLUENCE OF CARBON BURNOUT ON SUBMICRON PARTICLE FORMATION FROM EMULSIFIED FUEL OIL COMBUSTION

Science.gov (United States)

The paper gives results of an examination of particle behavior and particle size distributions from the combustion of different fuel oils and emulsified fuels in three experimental combusators. Results indicate that improved carbon (C) burnout from fule oil combustion, either by...

Emulsifying property of a viscous exopolysaccharide fromSphingomonas paucimobilis.

Science.gov (United States)

Ashtaputre, A A; Shah, A K

1995-03-01

A viscous exopolysaccharide fromSphingomonas paucimobilis-GS1, emulsified xylene, benzene, 2-methylnaphthalene, hexadecane, hexane, kerosene and paraffin oil as well as castor, coconut and olive oils when used at 1 mg/ml. It stabilized the emulsions more efficiently than commercial gums such as arabic, tragacanth, karaya and xanthan. Emulsions were stable for 6 months, from 4 to 40°C and pH 4 to 10 and in the presence of NaCl up to 50 g/l. The polysaccharide had no discernible toxicity towards mice when tested using World Health Organization guidelines.

Eudaemon : Involuntary and on-demand emulation against zero-day exploits

NARCIS (Netherlands)

Portokalidis, Georgios; Bos, Herbert

2008-01-01

Eudaemon is a technique that aims to blur the borders between protected and unprotected applications, and brings together honeypot technology and end-user intrusion detection and prevention. Eudaemon is able to attach to any running process, and redirect execution to a user-space emulator that will

Simulated, Emulated, and Physical Investigative Analysis (SEPIA) of networked systems.

Energy Technology Data Exchange (ETDEWEB)

Burton, David P.; Van Leeuwen, Brian P.; McDonald, Michael James; Onunkwo, Uzoma A.; Tarman, Thomas David; Urias, Vincent E.

2009-09-01

This report describes recent progress made in developing and utilizing hybrid Simulated, Emulated, and Physical Investigative Analysis (SEPIA) environments. Many organizations require advanced tools to analyze their information system's security, reliability, and resilience against cyber attack. Today's security analysis utilize real systems such as computers, network routers and other network equipment, computer emulations (e.g., virtual machines) and simulation models separately to analyze interplay between threats and safeguards. In contrast, this work developed new methods to combine these three approaches to provide integrated hybrid SEPIA environments. Our SEPIA environments enable an analyst to rapidly configure hybrid environments to pass network traffic and perform, from the outside, like real networks. This provides higher fidelity representations of key network nodes while still leveraging the scalability and cost advantages of simulation tools. The result is to rapidly produce large yet relatively low-cost multi-fidelity SEPIA networks of computers and routers that let analysts quickly investigate threats and test protection approaches.

Emulating conventional operator interfaces on window-based workstations

International Nuclear Information System (INIS)

Carr, G.P.

1990-01-01

This paper explores an approach to support the LAMPF and PSR control systems on VAX/VMS workstations using DECwindows and VI Corporation Data Views as the operator interface. The PSR control system was recently turned over to MP division and the two control-system staffs were merged into one group. One of the goals of this new group is to develop a common workstation-based operator console and interface which can be used in a single control room controlling both the linac and proton storage ring. The new console operator interface will need a high-level graphics toolkit for its implementation. During the conversion to the new consoles it will also probably be necessary to write a package to emulate the current operator interfaces at the software level. This paper describes a project to evaluate the appropriateness of VI Corporation's Data Views graphics package for use in the LAMPF control-system environment by using it to write an emulation of the LAMPF touch-panel interface to a large LAMPF control-system application program. A secondary objective of this project was to explore any productivity increases that might be realized by using an object-oriented graphics package and graphics editor. (orig.)

Emulation of reionization simulations for Bayesian inference of astrophysics parameters using neural networks

Science.gov (United States)

Schmit, C. J.; Pritchard, J. R.

2018-03-01

Next generation radio experiments such as LOFAR, HERA, and SKA are expected to probe the Epoch of Reionization (EoR) and claim a first direct detection of the cosmic 21cm signal within the next decade. Data volumes will be enormous and can thus potentially revolutionize our understanding of the early Universe and galaxy formation. However, numerical modelling of the EoR can be prohibitively expensive for Bayesian parameter inference and how to optimally extract information from incoming data is currently unclear. Emulation techniques for fast model evaluations have recently been proposed as a way to bypass costly simulations. We consider the use of artificial neural networks as a blind emulation technique. We study the impact of training duration and training set size on the quality of the network prediction and the resulting best-fitting values of a parameter search. A direct comparison is drawn between our emulation technique and an equivalent analysis using 21CMMC. We find good predictive capabilities of our network using training sets of as low as 100 model evaluations, which is within the capabilities of fully numerical radiative transfer codes.

Transdermal solid delivery of epigallocatechin-3-gallate using self-double-emulsifying drug delivery system as vehicle: Formulation, evaluation and vesicle-skin interaction.

Science.gov (United States)

Hu, Caibiao; Gu, Chengyu; Fang, Qiao; Wang, Qiang; Xia, Qiang

2016-02-01

The present study investigated a self-double-emulsifying drug delivery system loaded with epigallocatechin-3-gallate to improve epigallocatechin-3-gallate skin retention. The long chain solid lipids (cetostearyl alcohol) and macadamia oil were utilized as a carrier to deliver the bioactive ingredient. Response surface methodology was used to optimize the formulation, and the solid lipid to total lipid weight ratio, concentration of epigallocatechin-3-gallate and hydrophilic surfactant on skin retention were found to be the principal factors. The optimum formulation with high encapsulation efficiency (95.75%), self-double-emulsification performance (99.58%) and skin retention (87.24%) were derived from the fitted models and experimentally examined, demonstrating a reasonable agreement between experimental and predicted values. Epigallocatechin-3-gallate-self-double-emulsifying drug delivery system was found to be stable for 3 months. Transdermal studies could explain a higher skin diffusion of epigallocatechin-3-gallate from the self-double-emulsifying drug delivery system compared with EGCG aqueous solution. In vitro cytotoxicity showed that epigallocatechin-3-gallate-self-double-emulsifying drug delivery system did not exert hazardous effect on L929 cells up to 1:10. © The Author(s) 2015.

Continuous-variable quantum authentication of physical unclonable keys: Security against an emulation attack

Science.gov (United States)

Nikolopoulos, Georgios M.

2018-01-01

We consider a recently proposed entity authentication protocol in which a physical unclonable key is interrogated by random coherent states of light, and the quadratures of the scattered light are analyzed by means of a coarse-grained homodyne detection. We derive a sufficient condition for the protocol to be secure against an emulation attack in which an adversary knows the challenge-response properties of the key and moreover, he can access the challenges during the verification. The security analysis relies on Holevo's bound and Fano's inequality, and suggests that the protocol is secure against the emulation attack for a broad range of physical parameters that are within reach of today's technology.

User authentication based on the NFC host-card-emulation technology

Science.gov (United States)

Kološ, Jan; Kotyrba, Martin

2017-11-01

This paper deals with implementation of algorithms for data exchange between mobile devices supporting NFC HCE (Host-Card-Emulation) and a contactless NFC reader communicating in a read/write mode. This solution provides multiplatform architecture for data exchange between devices with a focus on safe and simple user authentication.

Emulsifier-free emulsion polymerization of tetrafluoroethylene by radiation. IV. Effects of additives on Polymer molecular weight

International Nuclear Information System (INIS)

Watanabe, T.; Suwa, T.; Okamoto, J.; Machi, S.

1979-01-01

Poly(tetrafluoroethylene)(PTFE) of high molecular weight, 4.5 x 10 7 , was incidentally obtained at earlier study of an emulsifier-free emulsion polymerization of tetrafluoroethylene by radiation. In order to clarify this phenomenon, the effects of additives, in particular radical scavengers, on the molecular weight of PTFE and its polymerization behavior were studied. It was found that the molecular weight of PTFE is increased by the addition of hydroquinone, benzoquinone, α-pinene, dl-limonene, and ethylenediamine but is decreased by oxygen and triethylamine. A PTFE latex with molecular weight higher than 2 x 10 7 was obtained in the presence of hydroquinone. It is concluded that additives such as hydroquinone and benzaquinone, which rapidly scavenge the primary radicals (OH, H, and e/sub aq/ - ) in the aqueous phase but not the growing polymer radicals in PTFE particles, are most effective in increasing the molecular weight

Long-Term Synaptic Plasticity Emulated in Modified Graphene Oxide Electrolyte Gated IZO-Based Thin-Film Transistors.

Science.gov (United States)

Yang, Yi; Wen, Juan; Guo, Liqiang; Wan, Xiang; Du, Peifu; Feng, Ping; Shi, Yi; Wan, Qing

2016-11-09

Emulating neural behaviors at the synaptic level is of great significance for building neuromorphic computational systems and realizing artificial intelligence. Here, oxide-based electric double-layer (EDL) thin-film transistors were fabricated using 3-triethoxysilylpropylamine modified graphene oxide (KH550-GO) electrolyte as the gate dielectrics. Resulting from the EDL effect and electrochemical doping between mobile protons and the indium-zinc-oxide channel layer, long-term synaptic plasticity was emulated in our devices. Synaptic functions including long-term memory, synaptic temporal integration, and dynamic filters were successfully reproduced. In particular, spike rate-dependent plasticity (SRDP), one of the basic learning rules of long-term plasticity in the neural network where the synaptic weight changes according to the rate of presynaptic spikes, was emulated in our devices. Our results may facilitate the development of neuromorphic computational systems.

Design and implementation of HMI and SCADA applied to a didactic emulation of a packing process

Directory of Open Access Journals (Sweden)

Manuel Alejandro Bohórquez-Dallos

2013-07-01

The supervision and control of the signals are performed with the CANopen protocol. The developed system allows the user to interact directly with the emulation of the process, triggering elements of it in the computer remotely and locally using the touch screen. The SCADA and HMI are embedded in a CoDeSys® function that the user can use as a learning tool for automating the process emulation.

Lecithin-linker formulations for self-emulsifying delivery of nutraceuticals.

Science.gov (United States)

Chu, Jacquelene; Cheng, Yu-Ling; Rao, A Venketeshwer; Nouraei, Mehdi; Zarate-Muñoz, Silvia; Acosta, Edgar J

2014-08-25

Lecithin-linker microemulsions are formulations produced with soybean lecithin in combination with a highly lipophilic (lipophilic linker) and highly hydrophilic (hydrophilic linkers) surfactant-like additives. In this work, lecithin-linker systems were formulated to produce self-emulsifying delivery systems for β-carotene and β-sitosterol. The concentration of the lipophilic linker, sorbitan monooleate, was adjusted to minimize the formation of liquid crystals. The concentration of hydrophilic linkers, decaglyceryl caprylate/caprate and PEG-6-caprylic/capric glycerides, was gradually increased (scanned) until single phase clear microemulsions were obtained. For these scans, the oil (ethyl caprate) to water ratio was set to 1. The single phase, clear microemulsions were diluted with fed-state simulated intestinal fluid (FeSSIF) and produced stable emulsions, with drop sizes close to 200 nm. Using pseudo-ternary phase diagrams to evaluate the process of dilution of microemulsion preconcentrates (mixtures of oil, lecithin and linkers with little or no water) with FeSSIF, it was determined that self-emulsifying systems are obtained when the early stages of the dilution produce single phase microemulsions. If liquid crystals or multiple phase systems are obtained during those early stages, then the emulsification yields unstable emulsions with large drop sizes. An in vitro permeability study conducted using a Flow-Thru Dialyzer revealed that stable emulsions with drop sizes of 150-300 nm produce large and irreversible permeation of β-carotene to sheep intestine. On the other hand, unstable emulsions produced without the linker combination separated in the dialyzer chamber. Copyright © 2014 Elsevier B.V. All rights reserved.

Sucrose polyesters from poultry fat as non-ionic emulsifiers

Directory of Open Access Journals (Sweden)

Megahed, Mohamed G.

2000-12-01

Full Text Available Poultry fats are rich in palmitic and oleic acids are produced as by-products from poultry industries. These fats can be utilized in the preparation of emulsifiers. Sucrose esters of poultry fat are prepared from low-cost poultry fat and sucrose by esterification. The yield of sucrose esters prepared in this work exceeds than 85%. The hydrophilic-lipophilic balance (HLB, surface tension, interfacial tension and stability index (SI were evaluated and compared with standard emulsifiers prepared from pure palmitate and oleate esters. Concerning the stability of emulsions, the values of interfacial tension and HLB were higher for the sucrose esters of poultry fat.Las grasas de aves de corral son ricas en ácidos palmítico y oleico y son producidas como subproductos de las industrias avícolas. Estas grasas pueden ser utilizadas en la preparación de emulsionantes. Los ésteres de sacarosa de grasas de aves de corral fueron preparadas a partir de grasas de bajo coste y sacarosa por esterificación. El rendimiento de los ésteres de sacarosa preparados en este trabajo superó el 85%. El balance hidrofílicolipofílico (HLB, tensión superficial, tensión interfacial e índice de estabilidad (SI fueron evaluados y comparados con emulsionantes estandar preparados de ésteres de palmitato y oleato puros. Los valores de tensión interfacial y el HLB fueron más altos en los poliésteres de sacarosa de las grasas de aves de corral.

Emulation of long-term changes in global climate: application to the late Pliocene and future

Directory of Open Access Journals (Sweden)

N. S. Lord

2017-11-01

Full Text Available Multi-millennial transient simulations of climate changes have a range of important applications, such as for investigating key geologic events and transitions for which high-resolution palaeoenvironmental proxy data are available, or for projecting the long-term impacts of future climate evolution on the performance of geological repositories for the disposal of radioactive wastes. However, due to the high computational requirements of current fully coupled general circulation models (GCMs, long-term simulations can generally only be performed with less complex models and/or at lower spatial resolution. In this study, we present novel long-term continuous projections of climate evolution based on the output from GCMs, via the use of a statistical emulator. The emulator is calibrated using ensembles of GCM simulations, which have varying orbital configurations and atmospheric CO2 concentrations and enables a variety of investigations of long-term climate change to be conducted, which would not be possible with other modelling techniques on the same temporal and spatial scales. To illustrate the potential applications, we apply the emulator to the late Pliocene (by modelling surface air temperature – SAT, comparing its results with palaeo-proxy data for a number of global sites, and to the next 200 kyr (thousand years (by modelling SAT and precipitation. A range of CO2 scenarios are prescribed for each period. During the late Pliocene, we find that emulated SAT varies on an approximately precessional timescale, with evidence of increased obliquity response at times. A comparison of atmospheric CO2 concentration for this period, estimated using the proxy sea surface temperature (SST data from different sites and emulator results, finds that relatively similar CO2 concentrations are estimated based on sites at lower latitudes, whereas higher-latitude sites show larger discrepancies. In our second illustrative application, spanning the next

An overview of Linux container based network emulation

CSIR Research Space (South Africa)

Peach, Schalk

2016-07-01

Full Text Available , a remote procedure call (RPC) application programming interface (API), a Python library and various user interface (UI) enhancements. Additional goals of the CORE project are to allow wireless network experiments through the Extendable Mobile Ad... backend functionality, the design of the backend and the choice of virtualisation technologies. An additional comparison that is included is the capability of a CBE to distribute an emulation across multiple host machines. In Table 1, a preliminary model...

Alkyl caffeates as antioxidants in O/W emulsions: Impact of emulsifier type and endogenous tocopherols

DEFF Research Database (Denmark)

Sørensen, Ann-Dorit Moltke; Villeneuve, Pierre; Jacobsen, Charlotte

2017-01-01

, the aim was to evaluate the impact of emulsifiers (Citrem and Tween80) and presence of endogenous tocopherols on the efficacies of caffeic acid and caffeates (C1–C20) as antioxidants in emulsions. Lipid oxidation was evaluated during storage and partitioning of caffeic acid and caffeates was estimated...... by measuring their concentrations in the aqueous phase. Partitioning of caffeic acid and caffeates was influenced by emulsifier type and the presence of endogenous tocopherols. Caffeic acid was the most efficient antioxidant in Citrem and Tween stabilized emulsions in the presence of endogenous tocopherol....... In contrast, for Tween stabilized emulsions, caffeic acid acted as a prooxidant and the evaluated caffeates acted as strong antioxidants in the absence of endogenous tocopherol. Thus, when endogenous tocopherol was present lipophilization of caffeic acid did not increase its efficacy as an antioxidant...

Towards Emulation-as-a-Service: Cloud Services for Versatile Digital Object Access

Directory of Open Access Journals (Sweden)

Dirk von Suchodoletz

2013-06-01

Full Text Available The changing world of IT services opens the chance to more tightly integrate digital long-term preservation into systems, both for commercial and end users. The emergence of cloud offerings re-centralizes services, and end users interact with them remotely through standardized (web-client applications on their various devices. This offers the chance to use partially the same concepts and methods to access obsolete computer environments and allows for more sustainable business processes. In order to provide a large variety of user-friendly remote emulation services, especially in combination with authentic performance and user experience, a distributed system model and architecture is required, suitable to run as a cloud service, allowing for the specialization both of memory institutions and third party service providers.The shift of the usually non-trivial task of the emulation of obsolete software environments from the end user to specialized providers can help to simplify digital preservation and access strategies. Besides offering their users better access to their holdings, libraries and archives may gain new business opportunities to offer services to a third party, such as businesses requiring authentic reproduction of digital objects and processes for legal reasons. This paper discusses cloud concepts as the next logical step for accessing original digital material. Emulation-as-a-Service (EaaS fills the gap between the successful demonstration of emulation strategies as a long term access strategy and it’s perceived availability and usability. EaaS can build upon the ground of research and prototypical implementations of previous projects, and reuse well established remote access technology.In this article we develop requirements and a system model, suitable for a distributed environment. We will discuss the building blocks of the core services as well as requirements regarding access management. Finally, we will try to present a

Statistical Emulation of Climate Model Projections Based on Precomputed GCM Runs*

KAUST Repository

Castruccio, Stefano

2014-03-01

The authors describe a new approach for emulating the output of a fully coupled climate model under arbitrary forcing scenarios that is based on a small set of precomputed runs from the model. Temperature and precipitation are expressed as simple functions of the past trajectory of atmospheric CO2 concentrations, and a statistical model is fit using a limited set of training runs. The approach is demonstrated to be a useful and computationally efficient alternative to pattern scaling and captures the nonlinear evolution of spatial patterns of climate anomalies inherent in transient climates. The approach does as well as pattern scaling in all circumstances and substantially better in many; it is not computationally demanding; and, once the statistical model is fit, it produces emulated climate output effectively instantaneously. It may therefore find wide application in climate impacts assessments and other policy analyses requiring rapid climate projections.

Meltability and Stretchability of White Brined Cheese: Effect of Emulsifier Salts

OpenAIRE

Khaled Abu-Alruz; Ayman S. Mazahreh; Ali F. Al-Shawabkeh; Amer A. Omari; Jihad M. Quasem

2009-01-01

Problem statement: This study was based on the hypothesis that by adding low concentrations of emulsifier salts, may specifically act on the cross linking bonds of the protein matrix, to the original brine (storage medium) it would be possible to induce meltability and stretchability in white brined cheese. Approach: A new apparatus for measuring the actual stretchability was designed and constructed; measurements on different cheese samples proved its validity and reliability to measure stre...

Development and Optimization of Polymeric Self-Emulsifying Nanocapsules for Localized Drug Delivery: Design of Experiment Approach

Directory of Open Access Journals (Sweden)

Jyoti Wadhwa

2014-01-01

Full Text Available The purpose of the present study was to formulate polymeric self-emulsifying curcumin nanocapsules with high encapsulation efficiency, good emulsification ability, and optimal globule size for localized targeting in the colon. Formulations were prepared using modified quasiemulsion solvent diffusion method. Concentration of formulation variables, namely, X1 (oil, X2 (polymeric emulsifier, and X3 (adsorbent, was optimized by design of experiments using Box-Behnken design, for its impact on mean globule size (Y1 and encapsulation efficiency (Y2 of the formulation. Polymeric nanocapsules with an average diameter of 100–180 nm and an encapsulation efficiency of 64.85 ± 0.12% were obtained. In vitro studies revealed that formulations released the drug after 5 h lag time corresponding to the time to reach the colonic region. Pronounced localized action was inferred from the plasma concentration profile (Cmax 200 ng/mL that depicts limited systemic absorption. Roentgenography study confirms the localized presence of carrier (0–2 h in upper GIT; 2–4 h in small intestine; and 4–24 h in the lower intestine. Optimized formulation showed significantly higher cytotoxicity (IC50 value 20.32 μM in HT 29 colonic cancer cell line. The present study demonstrates systematic development of polymeric self-emulsifying nanocapsule formulation of curcumin for localized targeting in colon.

In situ SERS detection of emulsifiers at lipid interfaces using label-free amphiphilic gold nanoparticles.

Science.gov (United States)

Li, Yue; Driver, Michael; Winuprasith, Thunnalin; Zheng, Jinkai; McClements, David Julian; He, Lili

2014-10-21

Herein, we fabricated amphiphilic gold nanoparticles (GNPs) that can self-assemble at oil-water interfaces. We applied those GNPs for in situ SERS detection of emulsifier molecules within the interfacial region of oil in water (O/W) emulsion systems.

The influence of carbohydrate-based fat replacers with and without emulsifiers on the quality characteristics of lowfat cake.

Science.gov (United States)

Khalil, A H

1998-01-01

Physical and sensory characteristics of cakes prepared with either the carbohydrate-based fat replacers N-Flate, Paselli MD 10 and Litesse (0, 25, 50 and 75% of fat weight) or fat replacers plus emulsifier (mono- and diglycerides; 0 and 3% of flour weight) were studied. Specific gravity of the batter was significantly (p Cakes prepared with fat replacers at the 25 and 50% levels had higher volumes, specific volume and standing heights than those of the control. Cakes prepared with fat replacers at the 25, 50 and 75% levels were more compressible than the control. Cakes prepared with Paselli MD 10 had the highest volumes, specific volume, standing heights and compressibilities. Incorporation of emulsifier with fat replacers improved cake volumes, standing heights and compressibilities. Cakes prepared with fat replacers exhibited higher crust and crumb color values compared to the control. Cakes prepared with 25 or 50% fat replacers had higher mean scores for flavor, softness and eating quality than the control. Incorporation of emulsifier with fat replacers did not affect the crust color, crumb color and flavor, but significantly (p < or = 0.05) improved softness and eating quality.

Application of thin film composite membranes with forward osmosis technology for the separation of emulsified oil-water

KAUST Repository

Duong, Hoang Hanh Phuoc; Chung, Neal Tai-Shung

2014-01-01

Large amounts of oily wastewater have been produced from various industries. The main challenge of oily wastewater treatments is to separate the stable emulsified oil particles from water. Therefore, the aim of this study is to investigate the effectiveness of forward osmosis (FO) processes to treat the stable oil-water emulsions. The FO technique has been demonstrated successfully for the treatment of a wide range of oil-water emulsions from a low to a very high concentration up to 200,000. ppm. The dependence of separation performance on oily feed concentration and flow rate has been investigated. Water can be separated from oily feeds containing 500. ppm or 200,000. ppm emulsified oil at a relatively high flux of 16.5±1.2. LMH or 11.8±1.6. LMH respectively by using a thin film composite membrane PAN-TFC and 1. M NaCl as the draw solution. Moreover, this membrane can achieve an oil rejection of 99.88% to produce water with a negligible oil level. Due to the presence of emulsified oil particles in the oily feed solutions, the membrane fouling has been addressed in this study. Better anti-fouling TFC FO membranes are needed. © 2013 Elsevier B.V.

Application of thin film composite membranes with forward osmosis technology for the separation of emulsified oil-water

KAUST Repository

Duong, Hoang Hanh Phuoc

2014-02-01

Large amounts of oily wastewater have been produced from various industries. The main challenge of oily wastewater treatments is to separate the stable emulsified oil particles from water. Therefore, the aim of this study is to investigate the effectiveness of forward osmosis (FO) processes to treat the stable oil-water emulsions. The FO technique has been demonstrated successfully for the treatment of a wide range of oil-water emulsions from a low to a very high concentration up to 200,000. ppm. The dependence of separation performance on oily feed concentration and flow rate has been investigated. Water can be separated from oily feeds containing 500. ppm or 200,000. ppm emulsified oil at a relatively high flux of 16.5±1.2. LMH or 11.8±1.6. LMH respectively by using a thin film composite membrane PAN-TFC and 1. M NaCl as the draw solution. Moreover, this membrane can achieve an oil rejection of 99.88% to produce water with a negligible oil level. Due to the presence of emulsified oil particles in the oily feed solutions, the membrane fouling has been addressed in this study. Better anti-fouling TFC FO membranes are needed. © 2013 Elsevier B.V.

Efeito do pH e da hidrólise tríptica sobre as propriedades emulsionantes da globina bovina The effect of the pH and the tryptic hydrolysis on the emulsifying properties of bovine globin

Directory of Open Access Journals (Sweden)

Cleia Batista Dias ORNELLAS

2001-01-01

Full Text Available No intuito de estudar o efeito do pH e da ação da tripsina sobre as propriedades emulsionantes da globina bovina, extraída pelo método da acetona acidificada, foram determinados neste trabalho, a capacidade emulsionante (EC, o índice de atividade emulsionante (EAI e a estabilidade da emulsão (ES. Testaram-se os valores de pH de 3,0 a 8,0 e os tempos de hidrólise de 5,0 a 60 min. Os dados obtidos indicam que os maiores valores de EC e ES foram obtidos no pH 5,0 e 6,0, respectivamente, correspondente à faixa de alta solubilidade da proteína. Por outro lado, o EAI, além de apresentar um máximo no pH 3,0, foi igualmente elevado nos valores de pH 7,0 e 8,0, situados na zona onde a globina é praticamente insolúvel. A hidrólise tríptica, nas condições empregadas, contribuiu para melhorar a EC, em toda a faixa de pH estudada, enquanto que para o EAI somente foi benéfico em pH 4,0 e 5,0. No caso da ES, este tratamento enzimático não foi vantajoso, promovendo melhoras apenas no pH 7,0, onde a proteína é insolúvel, e somente após 60 min de hidrólise.The effect of the pH and of the trypsin on the emulsifying properties of bovine globin, extracted by the acidified acetone method, was studied. The emulsifying capacity (EC, the emulsifying activity index (EAI and the emulsion stability (ES were determined at pH varying from 3.0 to 8.0 and employing hydrolysis times from 5 to 60 min. The highest vaules for EC and ES were obtained at pH 5.0 and 6.0, respectively, corresponding to the range of large protein solubility. On the other hand, the EAI was higher at pH 3.0 and also at pH 7.0 and 8.0, where the protein is insoluble. The tryptic hydrolysis produced an increase in EC, in all pH ranges studied, while for the EAI the same effect was observed only in pH 4.0 and 5.0, and for ES at pH 7.0 after 60 min of hydrolysis.

A generic inertia emulation controller for multi-terminal VSC-HVDC systems

DEFF Research Database (Denmark)

Zhu, Jiebei; Guerrero, Josep M.; Booth, Campbell

2013-01-01

A generic Inertia Emulation Controller (INEC) for Multi-Terminal Voltage-source-converter based HVDC (VSC-MTDC) is proposed in this paper. The proposed INEC can be incorporated in any grid-side-voltage-source-converter (GVSC) station, allowing the MTDC terminal to contribute an inertial response...

Emulation Platform for Cyber Analysis of Wireless Communication Network Protocols

Energy Technology Data Exchange (ETDEWEB)

Van Leeuwen, Brian P. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Eldridge, John M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-11-01

Wireless networking and mobile communications is increasing around the world and in all sectors of our lives. With increasing use, the density and complexity of the systems increase with more base stations and advanced protocols to enable higher data throughputs. The security of data transported over wireless networks must also evolve with the advances in technologies enabling more capable wireless networks. However, means for analysis of the effectiveness of security approaches and implementations used on wireless networks are lacking. More specifically a capability to analyze the lower-layer protocols (i.e., Link and Physical layers) is a major challenge. An analysis approach that incorporates protocol implementations without the need for RF emissions is necessary. In this research paper several emulation tools and custom extensions that enable an analysis platform to perform cyber security analysis of lower layer wireless networks is presented. A use case of a published exploit in the 802.11 (i.e., WiFi) protocol family is provided to demonstrate the effectiveness of the described emulation platform.

Efficiency of emulsifier-free emulsions and emulsions containing rapeseed lecithin as delivery systems for vectorization and release of coenzyme Q10: physico-chemical properties and in vitro evaluation.

Science.gov (United States)

Kaci, M; Arab-Tehrany, E; Dostert, G; Desjardins, I; Velot, E; Desobry, S

2016-11-01

To improve the encapsulation and release of coenzyme Q10 (CoQ10), emulsifier-free-emulsions were developed with a new emulsification process using high-frequency ultrasound (HFU) at 1.7MHz. Nano-emulsions containing CoQ10 were prepared with or without rapeseed lecithin as an emulsifier. The emulsions prepared with HFU were compared with an emulsion of CoQ10 containing emulsifier prepared with the same emulsification technique as well as with emulsions prepared with low-frequency ultrasound coupled with high-pressure homogenization (LFU+HPH). The physico-chemical properties of the emulsions were determined by average droplet size measurement with nano-droplet tracking analysis, droplet surface charge with ζ potential measurement, surface tension and rheological behaviour. Emulsions made by LFU+HPH with an emulsifier showed lower droplet sizes due to cavitation generated by the HFU process. Surface tension results showed that there was no significant difference between emulsions containing lecithin emulsifier regardless of the preparation process or the inclusion of CoQ10. In vitro biocompatibility tests were performed on human mesenchymal stem cells in order to show the cytotoxicity of various formulations and the efficiency of CoQ10-loaded emulsions. In vitro tests proved that the vectors were not toxic. Furthermore, CoQ10 facilitated a high rate of cell proliferation and metabolic activity especially when in an emulsifier-free formulation. Copyright © 2016 Elsevier B.V. All rights reserved.

Modeling and Experimental Test of Grid-Tied Photovoltaic Cell Emulating System in the Stand-alone Mode

Directory of Open Access Journals (Sweden)

Vu Minh Phap

2017-06-01

Full Text Available In recent decades, generation of electricity from solar arrays has been increased to meet the world's growing energy demand. However, the utilization rate of the power conditioner in the grid-tied solar power system is low because the operation of solar panels is dependent on sunlight. Thus, we studied the method that the small scale wind power generating system in size from a few hundred watts to two or three kilowatts can be connected to the grid-tied power conditioner of the solar power system for residential applications with low power ratings (single phase, size is limited to 10kW by emulating characteristic of the solar panel. In this paper, we introduce the application of the grid-tied PV cell emulating system in the stand-alone mode to improve the utilization rate of the power conditioner. The simulation and experimental test results verify that the PV cell emulating system can operate the power conditioner of the gridtied solar power system.

Adjusting the operating characteristics to improve the performance of an emulsified palm oil methyl ester run diesel engine

International Nuclear Information System (INIS)

Debnath, Biplab K.; Sahoo, Niranjan; Saha, Ujjwal K.

2013-01-01

Highlights: ► The oxygenated biodiesel has a lower calorific value and emits higher NO X than diesel. ► The objective is to study the water in palm oil biodiesel emulsion in a diesel engine. ► The tests are performed at higher compression ratio and retarded injection timing. ► The results obtained are compared with a POME run diesel engine. ► Higher efficiency, lower ignition delay and emissions are the outcomes. - Abstract: The popularity of emulsified fuels as alternative to diesel is cumulative. The water in diesel emulsion is the most practiced one. The presence of water in emulsion and its micro-explosion reduces emissions. However, the emulsified biodiesel is not properly explored. The reason may be due to its lesser calorific value that does not augment efficiency. Alongside oxygenated biodiesel generally emits higher NO X than diesel. Therefore, the present investigation targets at finding the performance, combustion and emission characteristics of emulsified biodiesel in a diesel engine at an elevated compression ratio (CR) and retarded injection timing (IT). This is because; at this CR–IT combination emulsified fuel will be injected at the warmer environment, mechanically created inside the cylinder. The objective is to achieve a faster combustion, lower ignition delay (ID), improved performance and emission characteristics. The biodiesel used in this work is the palm oil methyl ester (POME). The prepared two-phase water in POME (WIP) emulsion is tested in a variable compression ratio (VCR) diesel engine at CR = 18 and IT = 20°BTDC. The results obtained are then compared with the POME run engine data under the same CR and IT specifications. Additionally, experiments have also been conducted in the same engine at CR = 17.5 and IT = 23°BTDC to compare its results with those of WIP and POME run engines

DESIGN AND IMPLEMENTATION OF POTENTIOMETER-BASED NONLINEAR TRANSDUCER EMULATOR

Directory of Open Access Journals (Sweden)

Sheroz Khan

2011-05-01

Full Text Available This work attempts to design and implement in hardware a transducer with a nonlinear response using potentiometer. Potentiometer is regarded as a linear transducer, while a the response of a nonlinear transducer can be treated as a concatenation of linear segments made out of the response curve of an actual nonlinear transducer at the points of inflections being exhibited by the nonlinear curve. Each straight line segment is characterized by its slope and a constant, called the y-intercept, which is ultimately realized by a corresponding electronic circuit. The complete circuit diagram is made of three stages: (i the input stage for range selection, (ii a digital logic to make appropriate selection, (iii a conditioning circuit for realizing a given straight-line segment identified by its relevant slope and reference voltage. The simulation of the circuit is carried using MULTISIM, and the designed circuit is afterward tested to verify that variations of the input voltage give us an output voltage very close to the response pattern envisaged in the analytical stage of the design. The utility of this work lies in its applications in emulating purpose built transducers that could be used to nicely emulate a transducer in a real world system that is to be controlled by a programmable digital system.

Global sensitivity analysis using emulators, with an example analysis of large fire plumes based on FDS simulations

Energy Technology Data Exchange (ETDEWEB)

Kelsey, Adrian [Health and Safety Laboratory, Harpur Hill, Buxton (United Kingdom)

2015-12-15

Uncertainty in model predictions of the behaviour of fires is an important issue in fire safety analysis in nuclear power plants. A global sensitivity analysis can help identify the input parameters or sub-models that have the most significant effect on model predictions. However, to perform a global sensitivity analysis using Monte Carlo sampling might require thousands of simulations to be performed and therefore would not be practical for an analysis based on a complex fire code using computational fluid dynamics (CFD). An alternative approach is to perform a global sensitivity analysis using an emulator. Gaussian process emulators can be built using a limited number of simulations and once built a global sensitivity analysis can be performed on an emulator, rather than using simulations directly. Typically reliable emulators can be built using ten simulations for each parameter under consideration, therefore allowing a global sensitivity analysis to be performed, even for a complex computer code. In this paper we use an example of a large scale pool fire to demonstrate an emulator based approach to global sensitivity analysis. In that work an emulator based global sensitivity analysis was used to identify the key uncertain model inputs affecting the entrainment rates and flame heights in large Liquefied Natural Gas (LNG) fire plumes. The pool fire simulations were performed using the Fire Dynamics Simulator (FDS) software. Five model inputs were varied: the fire diameter, burn rate, radiative fraction, computational grid cell size and choice of turbulence model. The ranges used for these parameters in the analysis were determined from experiment and literature. The Gaussian process emulators used in the analysis were created using 127 FDS simulations. The emulators were checked for reliability, and then used to perform a global sensitivity analysis and uncertainty analysis. Large-scale ignited releases of LNG on water were performed by Sandia National

Optimization of methylene blue removal by stable emulsified liquid membrane using Plackett-Burman and Box-Behnken designs of experiments.

Science.gov (United States)

Djenouhat, Meriem; Bendebane, Farida; Bahloul, Lynda; Samar, Mohamed E H; Ismail, Fadhel

2018-02-01

The stability of an emulsified liquid membrane composed of Span80 as a surfactant, D2EHPA as an extractant and sulfuric acid as an internal phase was first studied according to different diluents and many operating parameters using the Plackett-Burman design of experiments. Then the removal of methylene blue from an aqueous solution has been carried out using this emulsified liquid membrane at its stability conditions. The effects of operating parameters were analysed from the Box-Behnken design of experiments. The optimization of the extraction has been realized applying the response surface methodology and the results showed that the dye extraction yielding 98.72% was achieved at optimized conditions.

Self-Micro Emulsifying Drug Delivery Systems: a Strategy to Improve Oral Bioavailability

Directory of Open Access Journals (Sweden)

Vijay K. Sharma

Full Text Available Aim: Oral route has always been the favorite route of drug administration in many diseases and till today it is the first way investigated in the development of new dosage forms. The major problem in oral drug formulations is low and erratic bioavailability, which mainly results from poor aqueous solubility, thereby pose problems in their formulation. For the therapeutic delivery of lipophilic active moieties (BCS class II drugs, lipid based formulations are inviting increasing attention. Methods: To that aim, from the web sites of PubMed, HCAplus, Thomson, and Registry were used as the main sources to perform the search for the most significant research articles published on the subject. The information was then carefully analyzed, highlighting the most important results in the formulation and development of self-micro emulsifying drug delivery systems as well as its therapeutic activity. Results: Self-emulsifying drug delivery system (SMEDDS has gained more attention due to enhanced oral bio-availability enabling reduction in dose, more consistent temporal profiles of drug absorption, selective targeting of drug(s toward specific absorption window in GIT, and protection of drug(s from the unreceptive environment in gut. Conclusions: This article gives a complete overview of SMEDDS as a promising approach to effectively deal with the problem of poorly soluble molecules.

Emulation of a complex global aerosol model to quantify sensitivity to uncertain parameters

Directory of Open Access Journals (Sweden)

L. A. Lee

2011-12-01

Full Text Available Sensitivity analysis of atmospheric models is necessary to identify the processes that lead to uncertainty in model predictions, to help understand model diversity through comparison of driving processes, and to prioritise research. Assessing the effect of parameter uncertainty in complex models is challenging and often limited by CPU constraints. Here we present a cost-effective application of variance-based sensitivity analysis to quantify the sensitivity of a 3-D global aerosol model to uncertain parameters. A Gaussian process emulator is used to estimate the model output across multi-dimensional parameter space, using information from a small number of model runs at points chosen using a Latin hypercube space-filling design. Gaussian process emulation is a Bayesian approach that uses information from the model runs along with some prior assumptions about the model behaviour to predict model output everywhere in the uncertainty space. We use the Gaussian process emulator to calculate the percentage of expected output variance explained by uncertainty in global aerosol model parameters and their interactions. To demonstrate the technique, we show examples of cloud condensation nuclei (CCN sensitivity to 8 model parameters in polluted and remote marine environments as a function of altitude. In the polluted environment 95 % of the variance of CCN concentration is described by uncertainty in the 8 parameters (excluding their interaction effects and is dominated by the uncertainty in the sulphur emissions, which explains 80 % of the variance. However, in the remote region parameter interaction effects become important, accounting for up to 40 % of the total variance. Some parameters are shown to have a negligible individual effect but a substantial interaction effect. Such sensitivities would not be detected in the commonly used single parameter perturbation experiments, which would therefore underpredict total uncertainty. Gaussian process

Application of associative emulator neural network for power control of nuclear reactor

International Nuclear Information System (INIS)

Datta, A.K.; Bandyopadhyay, Somnath

1993-01-01

This paper addresses the question of how to perform on-line training of emulator neural network for power control in a nuclear reactor. The computation and convergence problem can be reduced by judicious choice of bidirectional associative recall. (author). 10 refs., 2 figs

Carcinogenicity study of the emulsifier TOSOM and the release agent TOS in Wistar rats

DEFF Research Database (Denmark)

Meyer, Otto A.; KRISTIANSEN, E.; GRY, J.

1993-01-01

Groups of 60 Wistar rats of each sex were fed diets containing 3, 6 or 12% of the margarine emulsifier TOSOM (thermally oxidized soybean oil interacted with mono- and diglycerides of fatty acids) for 2.5 yr. In addition, three groups of 60 rats of each sex were fed two products of the release agent...

Technical study on semi-object emulation of structural statics problem

International Nuclear Information System (INIS)

Mo Jun; Shi Pingan; Liu Xingfu; Liu Zhiyong; Fu Chunyu

2002-01-01

Structural strength analysis depends mainly on finite element method and experiments. For complex structural system, a rather large error can be caused by some uncertain factors, such as load distributions, boundary conditions and constitutive relations in numerical analysis. At the same time, owing to the limitation of measuring and testing techniques, the strength and stiffness of key components can not be estimated by using the limited test data. To simulate stresses accurately under complex static environment, improve man-machine interactive system, and make the best use of fore- and post-processing function in graphic data processing, the authors combine numerical analysis with experimental technique and have developed the semi-object emulation technique to analyze the nonlinear problem of structure statics. The modern optical measuring techniques and image processing techniques are firstly used for the method to acquire displacement data of the vessel surface, and the data are used for the boundary condition to determine the geometrical size of disfigurement in the wall of vessel and the stress level. The experimental verification of a given test model show that these adverse problem can be solved by using semi-object emulation technology

Real Time Emulation of Dynamic Tariff for Congestion Management in Distribution Networks

DEFF Research Database (Denmark)

Rasmussen, Theis Bo; Wu, Qiuwei; Huang, Shaojun

2016-01-01

This paper presents the real time evaluation of the dynamic tariff (DT) method for alleviating congestion in a distribution networks with high penetration of distributed energy resources (DERs). The DT method is implemented in a real time digital testing platform that emulates a real distribution...

Muscle emulation with DC motor and neural networks for biped robots.

Science.gov (United States)

Serhan, Hayssam; Nasr, Chaiban G; Henaff, Patrick

2010-08-01

This paper shows how to use a DC motor and its PID controller, to behave analogously to a muscle. A model of the muscle that has been learned by a NNARX (Neural Network Auto Regressive eXogenous) structure is used. The PID parameters are tuned by an MLP Network with a special indirect online learning algorithm. The calculation of the learning algorithm is performed based on a mathematical equation of the DC motor or with a Neural Network identification of the motor. For each of the two algorithms, the output of the muscle model is used as a reference for the DC motor control loop. The results show that we succeeded in forcing the physical system to behave in the same way as the muscle model with acceptable margin of error. An implementation in the knees of a simulated biped robot is realized. Simulation compares articular trajectories with and without the muscle emulator and shows that with muscle emulator, articular trajectories become closer to the human being ones and that total power consumption is reduced.

DEP: A Depression Emulation Program*

Science.gov (United States)

Webster, Charles; Glass, Richard M; Banks, Gordon

1988-01-01

Cognitive deficits can be studied by “lesioning” computer simulations of normal cognitive processes. DEP (Depression Emulation Program) implements key aspects of a computational theory of “normal” adaptive reactive depression. A theory of “normal” depression is a step toward a theory of “pathological” depression. Transient depressed mood caused by an environmental event may be an example of fallure-triggered reprogramming of the self-schema. We normally generate responses to our environment in a fast and effortless “compiled” mode. After experiencing a stable, internal, and global failure, we debug our self-schema in a slow and effortful “interpreted” mode. During debugging, we experience a cognitive loop, increased objectivity, decreased motivation, and fluctuating self-generalizations. DEP exhibits analogous behavior and suggests vulnerability in an emotional operating system that normally, and periodically, adapts to a changing environment. Computer simulation of cognitive deficit may become a valuable research tool in psychiatry and neurology.

Optimization of methylene blue removal by stable emulsified liquid membrane using Plackett–Burman and Box–Behnken designs of experiments

Science.gov (United States)

Djenouhat, Meriem; Bendebane, Farida; Bahloul, Lynda; Samar, Mohamed E. H.

2018-01-01

The stability of an emulsified liquid membrane composed of Span80 as a surfactant, D2EHPA as an extractant and sulfuric acid as an internal phase was first studied according to different diluents and many operating parameters using the Plackett–Burman design of experiments. Then the removal of methylene blue from an aqueous solution has been carried out using this emulsified liquid membrane at its stability conditions. The effects of operating parameters were analysed from the Box–Behnken design of experiments. The optimization of the extraction has been realized applying the response surface methodology and the results showed that the dye extraction yielding 98.72% was achieved at optimized conditions. PMID:29515841

Wireless Visual Sensor Network Robots- Based for the Emulation of Collective Behavior

Directory of Open Access Journals (Sweden)

Fredy Hernán Martinez Sarmiento

2012-03-01

Full Text Available We consider the problem of bacterial quorum sensing emulate on small mobile robots. Robots that reflect the behavior of bacteria are designed as mobile wireless camera nodes. They are able to structure a dynamic wireless sensor network. Emulated behavior corresponds to a simplification of bacterial quorum sensing, where the action of a network node is conditioned by the population density of robots(nodes in a given area. The population density reading is done visually using a camera. The robot makes an estimate of the population density of the images, and acts according to this information. The operation of the camera is done with a custom firmware, reducing the complexity of the node without loss of performance. It was noted the route planning and the collective behavior of robots without the use of any other external or local communication. Neither was it necessary to develop a model system, precise state estimation or state feedback.

Highly permeable double-skinned forward osmosis membranes for anti-fouling in the emulsified oil-water separation process

KAUST Repository

Duong, Hoang Hanh Phuoc; Chung, Neal Tai-Shung; Wei, Shawn; Irish, Lana

2014-01-01

Forward osmosis (FO) has attracted wide attention in recent years. However, the FO performance may be restricted due to internal concentration polarization (ICP) and fast fouling propensity that occurs in the membrane sublayer. Particularly, these problems significantly affect the membrane performance when treating highly contaminated oily wastewater. Recently, double-skinned flat sheet cellulose acetate (CA) membranes consisting of two selective skins via the phase inversion method have demonstrated less ICP and fouling propensity over typical single-skinned membranes. However, these membranes exhibit low water fluxes of <12 LMH under 2 M NaCl draw solution. Therefore, a novel double-skinned FO membrane with a high water flux has been aimed for in this study for emulsified oil-water treatment. The double-skinned FO membrane comprises a fully porous sublayer sandwiched between (i) a truly dense skin for salt rejection and (ii) a fairly loose dense skin for emulsified oil particle rejection. The former dense skin is a polyamide synthesized via interfacial polymerization, while the latter one is a self-assembled sulfonated pentablock copolymer (Nexar copolymer) layer. The resultant double-skinned membrane exhibits a high water flux of 17.2 LMH and a low reverse salt transport of 4.85 gMH using 0.5 M NaCl as the draw solution and DI water as the feed. The double-skinned membrane outperforms the single-skinned membrane with much lower fouling propensity for emulsified oil-water separation. © 2014 American Chemical Society.

Highly permeable double-skinned forward osmosis membranes for anti-fouling in the emulsified oil-water separation process

KAUST Repository

Duong, Hoang Hanh Phuoc

2014-04-15

Forward osmosis (FO) has attracted wide attention in recent years. However, the FO performance may be restricted due to internal concentration polarization (ICP) and fast fouling propensity that occurs in the membrane sublayer. Particularly, these problems significantly affect the membrane performance when treating highly contaminated oily wastewater. Recently, double-skinned flat sheet cellulose acetate (CA) membranes consisting of two selective skins via the phase inversion method have demonstrated less ICP and fouling propensity over typical single-skinned membranes. However, these membranes exhibit low water fluxes of <12 LMH under 2 M NaCl draw solution. Therefore, a novel double-skinned FO membrane with a high water flux has been aimed for in this study for emulsified oil-water treatment. The double-skinned FO membrane comprises a fully porous sublayer sandwiched between (i) a truly dense skin for salt rejection and (ii) a fairly loose dense skin for emulsified oil particle rejection. The former dense skin is a polyamide synthesized via interfacial polymerization, while the latter one is a self-assembled sulfonated pentablock copolymer (Nexar copolymer) layer. The resultant double-skinned membrane exhibits a high water flux of 17.2 LMH and a low reverse salt transport of 4.85 gMH using 0.5 M NaCl as the draw solution and DI water as the feed. The double-skinned membrane outperforms the single-skinned membrane with much lower fouling propensity for emulsified oil-water separation. © 2014 American Chemical Society.

Evaluating the accuracy of climate change pattern emulation for low warming targets

Science.gov (United States)

Tebaldi, Claudia; Knutti, Reto

2018-05-01

Global climate policy is increasingly debating the value of very low warming targets, yet not many experiments conducted with global climate models in their fully coupled versions are currently available to help inform studies of the corresponding impacts. This raises the question whether a map of warming or precipitation change in a world 1.5 °C warmer than preindustrial can be emulated from existing simulations that reach higher warming targets, or whether entirely new simulations are required. Here we show that also for this type of low warming in strong mitigation scenarios, climate change signals are quite linear as a function of global temperature. Therefore, emulation techniques amounting to linear rescaling on the basis of global temperature change ratios (like simple pattern scaling) provide a viable way forward. The errors introduced are small relative to the spread in the forced response to a given scenario that we can assess from a multi-model ensemble. They are also small relative to the noise introduced into the estimates of the forced response by internal variability within a single model, which we can assess from either control simulations or initial condition ensembles. Challenges arise when scaling inadvertently reduces the inter-model spread or suppresses the internal variability, both important sources of uncertainty for impact assessment, or when the scenarios have very different characteristics in the composition of the forcings. Taking advantage of an available suite of coupled model simulations under low-warming and intermediate scenarios, we evaluate the accuracy of these emulation techniques and show that they are unlikely to represent a substantial contribution to the total uncertainty.

Effects of emulsifier addition on the crystallization and melting behavior of palm olein and coconut oil.

Science.gov (United States)

Maruyama, Jessica Mayumi; Soares, Fabiana Andreia Schafer De Martini; D'Agostinho, Natalia Roque; Gonçalves, Maria Inês Almeida; Gioielli, Luiz Antonio; da Silva, Roberta Claro

2014-03-12

Two commercial emulsifiers (EM1 and EM2), containing predominantly monoacylglycerols (MAGs), were added in proportiond of 1.0 and 3.0% (w/w) to coconut oil and palm olein. EM1 consisted of approximately 90% MAGs, whereas EM2 consisted of approximately 50% MAGs. The crystallization behavior of these systems was evaluated by differential scanning calorimetry (DSC) and microscopy under polarized light. On the basis of DSC results, it was clear that the addition of EM2 accelerated the crystallization of coconut oil and delayed the crystallization of palm olein. In both oils EM2 addition led to the formation of smaller spherulites, and these effects improved the possibilities for using these fats as ingredients. In coconut oil the spherulites were maintained even at higher temperatures (20 °C). The addition of EM1 to coconut oil changed the crystallization pattern. In palm olein, the addition of 3.0% (w/w) of this emulsifier altered the pattern of crystallization of this fat.

Characterization of Acinetobacter baumannii strain PS3 in degradation of food emulsifiers

Science.gov (United States)

Nguyen, Ngoc Tuan; Tran, Tuyet Nhung; Ha, Thi Bich Ngoc

2018-04-01

Strain SP3 revealed the abilty to utilizes emulsifier which is widely used in the preparation of drugs, vaccines, food, cosmetics and skin care products as its sole carbon and energy source. Generation time ranges from 1.4 to 2.1 h on the polysorbate family. Strain was identified as Acinetobacter baumannii based on 16S rRNA gene and it could dispose 27 % polysorbate 80 within a day. The proposed mechanism for polysorbate utilization belongs to the β-oxidation.

Neural Network Emulation of Reionization Simulations

Science.gov (United States)

Schmit, Claude J.; Pritchard, Jonathan R.

2018-05-01

Next generation radio experiments such as LOFAR, HERA and SKA are expected to probe the Epoch of Reionization and claim a first direct detection of the cosmic 21cm signal within the next decade. One of the major challenges for these experiments will be dealing with enormous incoming data volumes. Machine learning is key to increasing our data analysis efficiency. We consider the use of an artificial neural network to emulate 21cmFAST simulations and use it in a Bayesian parameter inference study. We then compare the network predictions to a direct evaluation of the EoR simulations and analyse the dependence of the results on the training set size. We find that the use of a training set of size 100 samples can recover the error contours of a full scale MCMC analysis which evaluates the model at each step.

High Dynamic Performance Nonlinear Source Emulator

DEFF Research Database (Denmark)

Nguyen-Duy, Khiem; Knott, Arnold; Andersen, Michael A. E.

2016-01-01

As research and development of renewable and clean energy based systems is advancing rapidly, the nonlinear source emulator (NSE) is becoming very essential for testing of maximum power point trackers or downstream converters. Renewable and clean energy sources play important roles in both...... terrestrial and nonterrestrial applications. However, most existing NSEs have only been concerned with simulating energy sources in terrestrial applications, which may not be fast enough for testing of nonterrestrial applications. In this paper, a high-bandwidth NSE is developed that is able to simulate...... change in the input source but also to a load step between nominal and open circuit. Moreover, all of these operation modes have a very fast settling time of only 10 μs, which is hundreds of times faster than that of existing works. This attribute allows for higher speed and a more efficient maximum...

Phosphate Reduction in Emulsified Meat Products: Impact of Phosphate Type and Dosage on Quality Characteristics.

Science.gov (United States)

Glorieux, Seline; Goemaere, Olivier; Steen, Liselot; Fraeye, Ilse

2017-09-01

Phosphate reduction is of important industrial relevance in the manufacturing of emulsified meat products because it may give rise to a healthier product. The effect of seven different phosphate types was tested on the physicochemical and quality characteristics to select the most promising phosphate type for further cooked sausage manufacturing. Next, phosphate mass fraction was gradually reduced. Tetrasodium di- or pyrophosphate (TSPP) and sodium tripolyphosphate (STPP) increased pH, reduced structural properties, resulted in the highest emulsion stability, lowest cooking loss and had little effect on hardness. Based on the viscoelastic properties, a minimum mass fraction of 0.06% TSPP was sufficient to obtain an acceptable quality product. Rheology proved to be a very useful tool to evaluate the quality of meat products, as it gives insight in the structure of the meat product and especially the functional properties of meat proteins. Based on the obtained results, it can be concluded that the current amount of phosphate added to emulsified meat products can be significantly reduced with minimal loss of product quality.

Development and Evaluation of Liquid and Solid Self-Emulsifying Drug Delivery Systems for Atorvastatin

Directory of Open Access Journals (Sweden)

Anna Czajkowska-Kośnik

2015-11-01

Full Text Available The objective of this work was to design and characterize liquid and solid self-emulsifying drug delivery systems (SEDDS for poorly soluble atorvastatin. To optimize the composition of liquid atorvastatin-SEDDS, solubility tests, pseudoternary phase diagrams, emulsification studies and other in vitro examinations (thermodynamic stability, droplet size and zeta potential analysis were performed. Due to the disadvantages of liquid SEDDS (few choices for dosage forms, low stability and portability during the manufacturing process, attempts were also made to obtain solid SEDDS. Solid SEDDS were successfully obtained using the spray drying technique from two optimized liquid formulations, CF3 and OF2. Despite liquid SEDDS formulation, CF3 was characterized by lower turbidity, higher percentage transmittance and better self-emulsifying properties, and based on the in vitro dissolution study it can be concluded that better solubilization properties were exhibited by solid formulation OF2. Overall, the studies demonstrated the possibility of formulating liquid and solid SEEDS as promising carriers of atorvastatin. SEDDS, with their unique solubilization properties, provide the opportunity to deliver lipophilic drugs to the gastrointestinal tract in a solubilized state, avoiding dissolution—a restricting factor in absorption rate of BCS Class 2 drugs, including atorvastatin.

A facile method for emulsified oil-water separation by using polyethylenimine-coated magnetic nanoparticles

Science.gov (United States)

Lü, Ting; Qi, Dongming; Zhang, Dong; Lü, Yulan; Zhao, Hongting

2018-04-01

Oil spills and oily wastewater discharges from ships and industrial activities have serious impacts on the environment and human health. In this study, a class of easy-to-synthesize polyethylenimine (PEI)-coated Fe3O4 magnetic nanoparticles (MNPs) was successfully synthesized via a one-step coprecipitation method. The synthesized PEI-coated Fe3O4 MNPs were characterized by using multiple technologies and applied in emulsified oil-water separation for the first time. It was found that the PEI effectively tuned the surface charge and wettability of MNPs. As a result, the PEI-coated MNPs could successfully assemble at the oil-water interface and promote the coalescence of oil droplets, thereby facilitating the subsequent magnetic separation. Results showed that the oil-water separation performance was superior and enhanced with the increase of ionic strength. Recycling experiment indicated that the PEI-coated MNPs could be reused up to six times without showing a significant decrease in separation efficiency. All of these results suggested that the PEI-coated MNP could potentially be used as a class of promising nanomaterials for emulsified oil-water separation. [Figure not available: see fulltext.

Integration of a network aware traffic generation device into a computer network emulation platform

CSIR Research Space (South Africa)

Von Solms, S

2014-07-01

Full Text Available Flexible, open source network emulation tools can provide network researchers with significant benefits regarding network behaviour and performance. The evaluation of these networks can benefit greatly from the integration of realistic, network...

A novel sample preparation method using rapid nonheated saponification method for the determination of cholesterol in emulsified foods.

Science.gov (United States)

Jeong, In-Seek; Kwak, Byung-Man; Ahn, Jang-Hyuk; Leem, Donggil; Yoon, Taehyung; Yoon, Changyong; Jeong, Jayoung; Park, Jung-Min; Kim, Jin-Man

2012-10-01

In this study, nonheated saponification was employed as a novel, rapid, and easy sample preparation method for the determination of cholesterol in emulsified foods. Cholesterol content was analyzed using gas chromatography with a flame ionization detector (GC-FID). The cholesterol extraction method was optimized for maximum recovery from baby food and infant formula. Under these conditions, the optimum extraction solvent was 10 mL ethyl ether per 1 to 2 g sample, and the saponification solution was 0.2 mL KOH in methanol. The cholesterol content in the products was determined to be within the certified range of certified reference materials (CRMs), NIST SRM 1544 and SRM 1849. The results of the recovery test performed using spiked materials were in the range of 98.24% to 99.45% with an relative standard devitation (RSD) between 0.83% and 1.61%. This method could be used to reduce sample pretreatment time and is expected to provide an accurate determination of cholesterol in emulsified food matrices such as infant formula and baby food. A novel, rapid, and easy sample preparation method using nonheated saponification was developed for cholesterol detection in emulsified foods. Recovery tests of CRMs were satisfactory, and the recoveries of spiked materials were accurate and precise. This method was effective and decreased the time required for analysis by 5-fold compared to the official method. © 2012 Institute of Food Technologists®

Physical, rheological, functional and film properties of a novel emulsifier: Frost grape polysaccharide (FGP) from Vitis riparia Michx

Science.gov (United States)

A novel emulsifier, Frost grape polysaccharide (FGP), isolated from natural exudate of the species Vitis riparia Michx, was physically and rheologically characterized. The determination of the physical, structural, thermodynamic, emulsification, film, and rheological properties of FGP provide essent...

Changes of lipid and fatty acid absorption induced by high dose of citric acid ester and lecithin emulsifiers.

Science.gov (United States)

Sadouki, Mohamed; Bouchoucha, Michel

2014-09-01

To describe the effect of two food emulsifiers, lecithin (E322) and citric acid esters of mono-and diglycerides of fatty acids (E472c), on the intestinal absorption of lipids. The experiment was conducted on 24 male Wistar rats randomly assigned in three groups. For two groups of six rats, 30% of the lipid intake was replaced with lecithin (L) or citric acid ester of mono and diglycerides, (E); the remaining 12 rats were the control group (C). Diet and fecal fat analysis was used to determine the apparent lipid absorption (ALA) and fatty acids. ALA was significantly lower in the group E than in the groups C and L (p acids decreased while the length of the carbon chains increased, and this decrease was higher in the group E. E472c emulsifier decreased the intestinal absorption of lipids.

Integration of drinking water treatment plant process models and emulated process automation software

NARCIS (Netherlands)

Worm, G.I.M.

2012-01-01

The objective of this research is to limit the risks of fully automated operation of drinking water treatment plants and to improve their operation by using an integrated system of process models and emulated process automation software. This thesis contains the design of such an integrated system.

Emulation and design of terahertz reflection-mode confocal scanning microscopy based on virtual pinhole

Science.gov (United States)

Yang, Yong-fa; Li, Qi

2014-12-01

In the practical application of terahertz reflection-mode confocal scanning microscopy, the size of detector pinhole is an important factor that determines the performance of spatial resolution characteristic of the microscopic system. However, the use of physical pinhole brings some inconvenience to the experiment and the adjustment error has a great influence on the experiment result. Through reasonably selecting the parameter of matrix detector virtual pinhole (VPH), it can efficiently approximate the physical pinhole. By using this approach, the difficulty of experimental calibration is reduced significantly. In this article, an imaging scheme of terahertz reflection-mode confocal scanning microscopy that is based on the matrix detector VPH is put forward. The influence of detector pinhole size on the axial resolution of confocal scanning microscopy is emulated and analyzed. Then, the parameter of VPH is emulated when the best axial imaging performance is reached.

HAZARDOUS AIR POLLUTANTS FROM THE COMBUSTION OF AN EMULSIFIED HEAVY FUEL OIL IN A FIRETUBE BOILER

Science.gov (United States)

The report gives results of measuring emissions of hazardous air pollutants (HAPs) from the combustion flue gases of a No. 6 fuel oil, both with and without an emulsifying agent, in a 2.5 million Btu/hr (732 kW) firetube boiler with the purpose of determining the impacts of the e...

RENEW: a real-time and effective network emulator of windows for IPv6

Science.gov (United States)

Zhao, Bing; Jin, Zhigang; Shu, Yantai; Li, Yu; Cen, Dan

2007-09-01

Although IPv4 is still working, IPv6 is considered as the backbone and characteristic of the NGI. With the development of Internet, new protocols and network equipments are required to develop. It is necessary to test the new protocols and network equipments extensively before deployment. This paper proposes the design and implementation of RENEW, a useable and accurate network emulator which supports both IPv4 and IPv6 protocols. Besides, it also works on Windows platform. In our IPv6 testbed, we use RENEW to emulate various network characteristics and conditions including bandwidth, delay packet loss and jitter. Compared with the expected values, results are acceptable. Through implementation and experimentation study, we have shown that RENEW does provide the real-time control and change on the parameters of IPv6 network conditions effectively and expediently on Windows. It also gives enough accuracy and more satisfactory convenience to the development and test work for the new protocols.

Primary Displacement Damage Calculation Induced by Neutron and Ion Using Binary Collision Approximation Techniques (Marlowe Code)

International Nuclear Information System (INIS)

Mota, F.; Ortiz, C. J.; Vila, R.

2012-01-01

Irradiation Experimental Area of TechnoFusion will emulate the extreme irradiation fusion conditions in materials by means of three ion accelerators: one used for self-implanting heavy ions (Fe, Si, C,...) to emulate the displacement damage induced by fusion neutrons and the other two for light ions (H and He) to emulate the transmutation induced by fusion neutrons. This Laboratory will play an essential role in the selection of functional materials for DEMO reactor since it will allow reproducing the effects of neutron radiation on fusion materials. Ion irradiation produces little or no residual radioactivity, allowing handling of samples without the need for special precautions. Currently, two different methods are used to calculate the primary displacement damage by neutron irradiation or by ion irradiation. On one hand, the displacement damage doses induced by neutrons are calculated considering the NRT model based on the electronic screening theory of Linhard. This methodology is commonly used since 1975. On the other hand, for experimental research community the SRIM code is commonly used to calculate the primary displacement damage dose induced by ion irradiation. Therefore, both methodologies of primary displacement damage calculation have nothing in common. However, if we want to design ion irradiation experiments capable to emulate the neutron fusion effect in materials, it is necessary to develop comparable methodologies of damage calculation for both kinds of radiation. It would allow us to define better the ion irradiation parameters (Ion, current, Ion energy, dose, etc) required to emulate a specific neutron irradiation environment. Therefore, our main objective was to find the way to calculate the primary displacement damage induced by neutron irradiation and by ion irradiation starting from the same point, that is, the PKA spectrum. In order to emulate the neutron irradiation that would prevail under fusion conditions, two approaches are contemplated: a) on

Measuring the emulsification dynamics and stability of self-emulsifying drug delivery systems.

Science.gov (United States)

Vasconcelos, Teófilo; Marques, Sara; Sarmento, Bruno

2018-02-01

Self-emulsifying drug delivery systems (SEDDS) are one of the most promising technologies in the drug delivery field, particularly for addressing solubility and bioavailability issues of drugs. The development of these drug carriers excessively relies in visual observations and indirect determinations. The present manuscript intended to describe a method able to measure the emulsification of SEDDS, both micro and nano-emulsions, able to measure the droplet size and to evaluate the physical stability of these formulations. Additionally, a new process to evaluate the physical stability of SEDDS after emulsification was also proposed, based on a cycle of mechanical stress followed by a resting period. The use of a multiparameter continuous evaluation during the emulsification process and stability was of upmost value to understand SEDDS emulsification process. Based on this method, SEDDS were classified as fast and slow emulsifiers. Moreover, emulsification process and stabilization of emulsion was subject of several considerations regarding the composition of SEDDS as major factor that affects stability to physical stress and the use of multicomponent with different properties to develop a stable and robust SEDDS formulation. Drug loading level is herein suggested to impact droplets size of SEDDS after dispersion and SEDDS stability to stress conditions. The proposed protocol allows an online measurement of SEDDS droplet size during emulsification and a rationale selection of excipients based on its emulsification and stabilization performance. Copyright © 2017. Published by Elsevier B.V.

Anti-cancer evaluation of quercetin embedded PLA nanoparticles synthesized by emulsified nanoprecipitation.

Science.gov (United States)

Pandey, Sanjeev K; Patel, Dinesh K; Thakur, Ravi; Mishra, Durga P; Maiti, Pralay; Haldar, Chandana

2015-04-01

This study was carried out to synthesize quercetin (Qt) embedded poly(lactic acid) (PLA) nanoparticles (PLA-Qt) and to evaluate anti-cancer efficacy of PLA-Qt by using human breast cancer cells. PLA-Qt were synthesized by using novel emulsified nanoprecipitation technique with varying dimension of 32 ± 8 to 152 ± 9 nm of PLA-Qt with 62 ± 3% (w/w) entrapment efficiency by varying the concentration of polymer, emulsifier, drug and preparation temperature. The dimension of PLA-Qt was measured through transmission electron microscopy indicating larger particle size at higher concentration of PLA. The release rate of Qt from PLA-Qt was found to be more sustained for larger particle dimension (152 ± 9 nm) as compared to smaller particle dimension (32 ± 8 nm). Interaction between Qt and PLA was verified through spectroscopic and calorimetric methods. Delayed diffusion and stronger interaction in PLA-Qt caused the sustained delivery of Qt from the polymer matrix. In vitro cytotoxicity study indicate the killing of ∼ 50% breast cancer cells in two days at 100 μg/ml of drug concentration while the ∼ 40% destruction of cells require 5 days for PLA-Qt (46 ± 6 nm; 20mg/ml of PLA). Thus our results propose anticancer efficacy of PLA-Qt nanoparticles in terms of its sustained release kinetics revealing novel vehicle for the treatment of cancer. Copyright © 2015 Elsevier B.V. All rights reserved.

Emulsifying Property and Antioxidative Activity of Cuttlefish Skin Gelatin Modified with Oxidized Linoleic Acid and Oxidized Tannic Acid

NARCIS (Netherlands)

Aewsiri, T.; Benjakul, S.; Visessanguan, W.; Wierenga, P.A.; Gruppen, H.

2013-01-01

Cuttlefish skin gelatins modified with oxidized linoleic acid (OLA) and oxidized tannic acid (OTA) were characterized and determined for emulsifying properties and antioxidative activity. Modification of gelatin with 5% OTA increased the total phenolic content and 1,1-diphenyl-2-picrylhydrazyl,

Experimental demonstration of an improved EPON architecture using OFDMA for bandwidth scalable LAN emulation

DEFF Research Database (Denmark)

Deng, Lei; Zhao, Ying; Yu, Xianbin

2011-01-01

We propose and demonstrate an improved Ethernet passive optical network (EPON) architecture supporting bandwidth-scalable physical layer local area network (LAN) emulation. Due to the use of orthogonal frequency division multiple access (OFDMA) technology for the LAN traffic transmission, there i...

Engine performance and emission of compression ignition engine fuelled with emulsified biodiesel-water

Science.gov (United States)

Maawa, W. N.; Mamat, R.; Najafi, G.; Majeed Ali, O.; Aziz, A.

2015-12-01

The depletion of fossil fuel and environmental pollution has become world crucial issues in current era. Biodiesel-water emulsion is one of many possible approaches to reduce emissions. In this study, emulsified biodiesel with 4%, 6% and 8% of water contents were prepared to be used as fuel in a direct injection compression ignition engine. The performance indicator such as brake power, brake specific fuel consumption (BSFC) and brake thermal efficiency (BTE) and emissions such as NOx and particulate matter (PM) were investigated. The engine was set at constant speed of 2500 rpm and load from 20% to 60%. All the results were compared to B5 (blend of 95% petroleum diesel and 5% palm oil biodiesel) biodiesel. At low load, the BSFC decrease by 12.75% at 4% water ratio and decreased by 1.5% at 6% water ratio. However, the BSFC increases by 17.19% with increasing water ratio to 8% compared to B5. Furthermore, there was no significant decrease in brake power and BTE at 60% load. For 20% and 40% load there was some variance regarding to brake power and BTE. Significant reduction in NOx and PM emissions by 73.87% and 20.00% respectively were achieved with increasing water ratio to 8%. Overall, it is observed that the emulsified of biodiesel-water is an appropriate alternative fuel method to reduce emissions.

Characterization and emulsifying property of a novel bioemulsifier by Aeribacillus pallidus YM-1.

Science.gov (United States)

Zheng, C; Li, Z; Su, J; Zhang, R; Liu, C; Zhao, M

2012-07-01

  Biosurfactants and bioemulsifiers commonly have the advantages of biodegradability, low toxicity, selectivity and biocompatibility over chemically synthesized surfactants. The goal of the study is to present a novel bioemulsifier with great application potential.   Aeribacillus pallidus YM-1, isolated from crude oil contaminated soil, was found to produce a novel high molecular bioemulsifier with an emulsification index of 60 ± 1% without remarkable surface tension reduction (45·7 ± 0·1 mN m(-1) ). The number-average molecular weight was determined as 526 369 Da by gel permeation chromatography analysis. Bioemulsifier was subjected to FT-IR and a complex of carbohydrates (41·1%), lipids (47·6%) and proteins (11·3%) was determined.   The bioemulsifier of A. pallidus YM-1 was isolated from the glucose-based culture medium and characterized with the help of chemical analytical techniques. The bioemulsifier exhibited a promising emulsifying property for biotechnology application potential in bioremediation and microbial enhanced oil recovery.   This is the first report of the bioemulsifier production by A. pallidus. The potential emulsifying activity of the bioemulsifier in the present study may be explored in various biotechnological and industrial applications. © 2012 The Authors. Journal of Applied Microbiology © 2012 The Society for Applied Microbiology.

Uncertainty-based simulation-optimization using Gaussian process emulation: Application to coastal groundwater management

Science.gov (United States)

Rajabi, Mohammad Mahdi; Ketabchi, Hamed

2017-12-01

Combined simulation-optimization (S/O) schemes have long been recognized as a valuable tool in coastal groundwater management (CGM). However, previous applications have mostly relied on deterministic seawater intrusion (SWI) simulations. This is a questionable simplification, knowing that SWI models are inevitably prone to epistemic and aleatory uncertainty, and hence a management strategy obtained through S/O without consideration of uncertainty may result in significantly different real-world outcomes than expected. However, two key issues have hindered the use of uncertainty-based S/O schemes in CGM, which are addressed in this paper. The first issue is how to solve the computational challenges resulting from the need to perform massive numbers of simulations. The second issue is how the management problem is formulated in presence of uncertainty. We propose the use of Gaussian process (GP) emulation as a valuable tool in solving the computational challenges of uncertainty-based S/O in CGM. We apply GP emulation to the case study of Kish Island (located in the Persian Gulf) using an uncertainty-based S/O algorithm which relies on continuous ant colony optimization and Monte Carlo simulation. In doing so, we show that GP emulation can provide an acceptable level of accuracy, with no bias and low statistical dispersion, while tremendously reducing the computational time. Moreover, five new formulations for uncertainty-based S/O are presented based on concepts such as energy distances, prediction intervals and probabilities of SWI occurrence. We analyze the proposed formulations with respect to their resulting optimized solutions, the sensitivity of the solutions to the intended reliability levels, and the variations resulting from repeated optimization runs.

The use of perturbed physics ensembles and emulation in palaeoclimate reconstruction (Invited)

Science.gov (United States)

Edwards, T. L.; Rougier, J.; Collins, M.

2010-12-01

Climate is a coherent process, with correlations and dependencies across space, time, and climate variables. However, reconstructions of palaeoclimate traditionally consider individual pieces of information independently, rather than making use of this covariance structure. Such reconstructions are at risk of being unphysical or at least implausible. Climate simulators such as General Circulation Models (GCMs), on the other hand, contain climate system theory in the form of dynamical equations describing physical processes, but are imperfect and computationally expensive. These two datasets - pointwise palaeoclimate reconstructions and climate simulator evaluations - contain complementary information, and a statistical synthesis can produce a palaeoclimate reconstruction that combines them while not ignoring their limitations. We use an ensemble of simulators with perturbed parameterisations, to capture the uncertainty about the simulator variant, and our method also accounts for structural uncertainty. The resulting reconstruction contains a full expression of climate uncertainty, not just pointwise but also jointly over locations. Such joint information is crucial in determining spatially extensive features such as isotherms, or the location of the tree-line. A second outcome of the statistical analysis is a refined distribution for the simulator parameters. In this way, information from palaeoclimate observations can be used directly in quantifying uncertainty in future climate projections. The main challenge is the expense of running a large scale climate simulator: each evaluation of an atmosphere-ocean GCM takes several months of computing time. The solution is to interpret the ensemble of evaluations within an 'emulator', which is a statistical model of the simulator. This technique has been used fruitfully in the statistical field of Computer Models for two decades, and has recently been applied in estimating uncertainty in future climate predictions in the

Phosphate Reduction in Emulsifi ed Meat Products: Impact of Phosphate Type and Dosage on Quality Characteristics

Directory of Open Access Journals (Sweden)

Seline Glorieux

2017-01-01

Full Text Available Phosphate reduction is of important industrial relevance in the manufacturing of emulsifi ed meat products because it may give rise to a healthier product. The eff ect of seven diff erent phosphate types was tested on the physicochemical and quality characteristics to select the most promising phosphate type for further cooked sausage manufacturing. Next, phosphate mass fraction was gradually reduced. Tetrasodium di- or pyrophosphate (TSPP and sodium tripolyphosphate (STPP increased pH, reduced structural properties, resulted in the highest emulsion stability, lowest cooking loss and had litt le eff ect on hardness. Based on the viscoelastic properties, a minimum mass fraction of 0.06 % TSPP was suffi cient to obtain an acceptable quality product. Rheology proved to be a very useful tool to evaluate the quality of meat products, as it gives insight in the structure of the meat product and especially the functional properties of meat proteins. Based on the obtained results, it can be concluded that the current amount of phosphate added to emulsifi ed meat products can be signifi cantly reduced with minimal loss of product quality.

Characterization and emulsifying properties of β-lactoglobulin-gum Acacia Seyal conjugates prepared via the Maillard reaction.

Science.gov (United States)

Bi, Binwei; Yang, Hao; Fang, Yapeng; Nishinari, Katsuyoshi; Phillips, Glyn O

2017-01-01

Gum Acacia Seyal (ASY) is less valued than is gum Acacia Senegal, due to its poor emulsifying ability. The present study investigated the Maillard reaction between ASY and β-lactoglobulin (BLG) and its impact on the emulsifying properties of ASY. The reaction products of BLG/ASY mixture (r=1/4), prepared by dry-heating at 60°C and a relative humidity of 79%, as a function of incubation time, were characterized by SDS-PAGE, GPC-MALLS and DSC. The results showed that 12-24h of dry-heating under the given conditions was sufficient for conjugation, meanwhile avoiding the formation of deeply coloured and insoluble melanoidins. More than 64% of the protein was incorporated into ASY, resulting in a two-fold increase in arabinogalactan-protein (AGP) content and 3.5 times increase in weight-average molecular mass of ASY. The conjugation with BLG markedly improved the stability of ASY-stabilized emulsions and their resistance against severe conditions, such as low pH and high saline conditions. Copyright © 2016 Elsevier Ltd. All rights reserved.

The influence of raw material, added emulsifying salt and spray drying on cheese powder structure and hydration properties

DEFF Research Database (Denmark)

Felix da Silva, Denise; Larsen, Flemming Hofmann; Hougaard, Anni Bygvrå

2017-01-01

The present work has evaluated how raw material, addition of emulsifying salts (ES) and drying technology affect particle characteristics, structure, and hydration of cheese powders. In this context the spray drying technology induced the strongest effect on morphology and swelling of cheese powder...

Polycyclic aromatic hydrocarbon-emulsifier protein produced by Aspergillus brasiliensis (niger) in an airlift bioreactor following an electrochemical pretreatment.

Science.gov (United States)

Sánchez-Vázquez, Victor; Shirai, Keiko; González, Ignacio; Gutiérrez-Rojas, Mariano

2018-05-01

An emulsifier protein (EP) was produced and easily separated from oil-contaminated water as an economical substrate when Aspergillus brasiliensis, pretreated in a solid state culture with a controlled electric field, was used in an airlift bioreactor. The hydrocarbon-EP comprised 19.5% of the total protein, its purification enhanced the specific emulsifying activity (EA) seven times. The influence of operational conditions (pH and salt concentration) on the EA were assessed to characterise the emulsion stability. The EA was increased by 19% in alkaline environments (pH 7-11), but it was not affected by the presence of salt (0-35 g L -1 ). On the other hand, preheating the EP samples (60 °C) enhanced the EA by 2.5 times. Based on analysis of its EA, this EP can be applied as a bioremediation enhancer in contaminated soils. Copyright © 2018 Elsevier Ltd. All rights reserved.

Removal of emulsified oil in residual waters by means of dissolved air flotation

International Nuclear Information System (INIS)

Echeverri Londono, Carlos Alberto

1996-01-01

In this article is consigned a theoretical and experimental study on the treatment of industrial residual waters with emulsified oil, through the flotation process for dissolved air (FAD), changing some operation parameters and some importance topics, related with the process. The experimental results and the theoretical pattern, show that the removal of oil depends fundamentally on the chemical pretreatment. Efficiencies of removal of oil up of 99% they were obtained, using the dissolved air flotation with the help of coagulants

Amelioration of carbon tetrachloride-induced hepatic injury by emulsified Antrodia extract

Directory of Open Access Journals (Sweden)

Wei-Chih Chang

2018-03-01

Full Text Available Objective(s: Antrodia cinnamomea (AC is found with anti-inflammatory and immunomodulatory biological activities. In this study, we investigated the anti-hepatitis effect of the emulsified AC extract from RO water or supercritical fluid CO2 with ethanol co-solvent extract methods of AC preparations. Materials and Methods: Five groups of eight to ten weeks male rats with a count of ten for each group were studied to evaluate the protection of two kinds of AC extract from hepatic injury. Acute liver injury of rats was induced by injecting 40% carbon tetrachloride (CCl4 1 mg/kg intraperitoneally. Positive and negative control groups rats were perfused with CCl4 or isotonic saline, respectively. Experimental groups received oral administration once/day of AC preparations before CCl4 treatment: water AC extract (WAE group, or emulsified AC extract from supercritical fluid extraction (EAE group for 5 days, and sacrificed on the 6th day and the blood and liver samples were collected under chloral hydrate anesthesia. The anti-inflammatory, antioxidant markers, and relevant signaling pathways were measured (AST, ALT, ROS, IL-1, IL-6, NO, and COX-2, MAPKs, and caspase-3. Results: EAE at 50 mg/kg significantly decreased the serum AST, ALT, IL-1, IL-6, NO, and ROS levels. Both extracts reduced the activation of p-ERK in the liver samples, but EAE inhibited COX-2 and caspase-3 protein expression better than WAE. The EAE ameliorated CCl4-induced hepatic injury significantly; as compared with WAE and the positive control. Conclusion: The hepatoprotection of EAE could be attributed to the antioxidant and anti-inflammatory effects of Antrodia.

A learning-based autonomous driver: emulate human driver's intelligence in low-speed car following

Science.gov (United States)

Wei, Junqing; Dolan, John M.; Litkouhi, Bakhtiar

2010-04-01

In this paper, an offline learning mechanism based on the genetic algorithm is proposed for autonomous vehicles to emulate human driver behaviors. The autonomous driving ability is implemented based on a Prediction- and Cost function-Based algorithm (PCB). PCB is designed to emulate a human driver's decision process, which is modeled as traffic scenario prediction and evaluation. This paper focuses on using a learning algorithm to optimize PCB with very limited training data, so that PCB can have the ability to predict and evaluate traffic scenarios similarly to human drivers. 80 seconds of human driving data was collected in low-speed (car-following scenarios. In the low-speed car-following tests, PCB was able to perform more human-like carfollowing after learning. A more general 120 kilometer-long simulation showed that PCB performs robustly even in scenarios that are not part of the training set.

Manufacture and characterization of breast tissue phantoms for emulating benign lesions

Science.gov (United States)

Villamarín, J. A.; Rojas, M. A.; Potosi, O. M.; Narváez-Semanate, J. L.; Gaviria, C.

2017-11-01

Phantoms elaboration has turned a very important field of study during the last decades due to its applications in medicine. These objects are capable of emulating or mimicking acoustically biological tissues in which parameters like speed of sound (SOS) and attenuation are successfully attained. However, these materials are expensive depending on their characteristics (USD 460.00 - 6000.00) and is difficult to have precise measurements because of their composition. This paper presents the elaboration and characterization of low cost ( USD $25.00) breast phantoms which emulate histological normality and pathological conditions in order to support algorithm calibration procedures in imaging diagnosis. Quantitative ultrasound (QUS) was applied to estimate SOS and attenuation values for breast tissue (background) and benign lesions (fibroadenoma and cysts). Results showed values of the SOS and attenuation for the background between 1410 - 1450 m/s and 0.40 - 0.55 dB/cm at 1 MHz sampling frequency, respectively. On the other hand, the SOS obtained for the lesions ranges from 1350 to 1700 m/s and attenuation values between 0.50 - 1.80 dB/cm at 1 MHz. Finally, the fabricated phantoms allowed for obtaining ultrasonograms comparable with real ones whose acoustic parameters are in agree with those reported in the literature.

Neurokernel: An Open Source Platform for Emulating the Fruit Fly Brain.

Directory of Open Access Journals (Sweden)

Lev E Givon

Full Text Available We have developed an open software platform called Neurokernel for collaborative development of comprehensive models of the brain of the fruit fly Drosophila melanogaster and their execution and testing on multiple Graphics Processing Units (GPUs. Neurokernel provides a programming model that capitalizes upon the structural organization of the fly brain into a fixed number of functional modules to distinguish between these modules' local information processing capabilities and the connectivity patterns that link them. By defining mandatory communication interfaces that specify how data is transmitted between models of each of these modules regardless of their internal design, Neurokernel explicitly enables multiple researchers to collaboratively model the fruit fly's entire brain by integration of their independently developed models of its constituent processing units. We demonstrate the power of Neurokernel's model integration by combining independently developed models of the retina and lamina neuropils in the fly's visual system and by demonstrating their neuroinformation processing capability. We also illustrate Neurokernel's ability to take advantage of direct GPU-to-GPU data transfers with benchmarks that demonstrate scaling of Neurokernel's communication performance both over the number of interface ports exposed by an emulation's constituent modules and the total number of modules comprised by an emulation.

Resilient Coordination of Networked Multiagent Systems Based on Distributed State Emulators

OpenAIRE

Yucelen, Tansel; De La Torre, Gerardo

2014-01-01

This note studies resilient coordination of networked multiagent systems in the presence of misbehaving agents, i.e., agents that are subject to adversaries modeled as exogenous disturbances. Apart from the existing relevant literature that make specific assumptions on the graph topology and/or the fraction of misbehaving agents, we present an adaptive control architecture based on distributed state emulators and show that the nominal networked multiagent system behavior can be retrieved even...

Composition of legume soaking water and emulsifying properties in gluten-free bread.

Science.gov (United States)

Huang, San; Liu, Yuling; Zhang, Weihan; Dale, Kylie J; Liu, Silu; Zhu, Jingnan; Serventi, Luca

2018-04-01

Soaking of legumes results in the loss of macronutrients, micronutrients and phytochemicals. Fibre, protein and phytochemicals found in legumes exert emulsifying activity that may improve the structure and texture of gluten-free bread. The legume soaking water of haricot beans, garbanzo chickpeas, whole green lentils, split yellow peas and yellow soybeans were tested in this study for functional properties and use as food ingredients. Composition, physicochemical properties and effect on the quality of gluten-free bread were determined for each legume soaking water. Haricot beans and split yellow peas released the highest amount of solids in the legume soaking water: 1.89 and 2.38 g/100 g, respectively. Insoluble fibre was the main constituent of haricot beans legume soaking water, while water-soluble carbohydrates and protein were the major fraction of split yellow peas. High quantities of phenolics (∼400 µg/g) and saponins (∼3 mg/g) were found in the legume soaking water of haricot beans, whole green lentils and split yellow peas. High emulsifying activity (46 and 50%) was found for the legume soaking water of garbanzo chickpeas and split yellow peas, probably due to their protein content and high ratio of water-soluble carbohydrates to dry matter. Such activity resulted in softer texture of the gluten-free bread. A homogeneous structure of crumb pores was found for split yellow peas, opposing that of whole green lentils. A balance between the contents of yeast nutrients and antinutrients was the likely basis of the different appearances.

A Novel 100 kW Power Hardware-in-the-Loop Emulation Test Bench for Permanent Magnet Synchronous Machines with Nonlinear Magnetics

OpenAIRE

Schmitt, Alexander; Richter, Jan; Gommeringer, Mario; Wersal, Thomas; Braun, Michael

2016-01-01

This paper presents a high dynamic power hardware-inthe-loop (PHIL) emulation test bench to mimic arbitrary permanent magnet synchronous machines with nonlinear magnetics. The proposed PHIL test bench is composed of a high performance real-time simulation system to calculate the machine behaviour and a seven level modular multiphase multilevel converter to emulate the power flow of the virtual machine. The PHIL test bench is parametrized for an automotive synchronous machine and controlled by...

Novel Modified Elman Neural Network Control for PMSG System Based on Wind Turbine Emulator

Directory of Open Access Journals (Sweden)

Chih-Hong Lin

2013-01-01

Full Text Available The novel modified Elman neural network (NN controlled permanent magnet synchronous generator (PMSG system, which is directly driven by a permanent magnet synchronous motor (PMSM based on wind turbine emulator, is proposed to control output of rectifier (AC/DC power converter and inverter (DC/AC power converter in this study. First, a closed loop PMSM drive control based on wind turbine emulator is designed to generate power for the PMSG system according to different wind speeds. Then, the rotor speed of the PMSG, the voltage, and current of the power converter are detected simultaneously to yield better power output of the converter. Because the PMSG system is the nonlinear and time-varying system, two sets online trained modified Elman NN controllers are developed for the tracking controllers of DC bus power and AC power to improve output performance of rectifier and inverter. Finally, experimental results are verified to show the effectiveness of the proposed control scheme.

Development of a Radio Frequency Space Environment Path Emulator for Evaluating Spacecraft Ranging Hardware

Science.gov (United States)

Mitchell, Jason W.; Baldwin, Philip J.; Kurichh, Rishi; Naasz, Bo J.; Luquette, Richard J.

2007-01-01

The Formation Flying Testbed (FFTB) at the National Aeronautics and Space Administration (NASA) Goddard Space Flight Center (GSFC) provides a hardware-in-the-loop test environment for formation navigation and control. The facility is evolving as a modular, hybrid, dynamic simulation facility for end-to-end guidance, navigation and. control (GN&C) design and analysis of formation flying spacecraft. The core capabilities of the FFTB, as a platform for testing critical hardware and software algorithms in-the-loop, have expanded to include S-band Radio Frequency (RF) modems for inter-spacecraft communication and ranging. To enable realistic simulations that require RF ranging sensors for relative navigation, a mechanism is needed to buffer the RF signals exchanged between spacecraft that accurately emulates the dynamic environment through which the RF signals travel, including the effects of medium, moving platforms, and radiated power. The Path Emulator for RF Signals (PERFS), currently under development at NASA GSFC, provides this capability. The function and performance of a prototype device are presented.

Novel self-emulsifying formulation of quercetin for improved in vivo antioxidant potential

DEFF Research Database (Denmark)

Jain, Sanyog; Jain, Amit K; Pohekar, Milind

2013-01-01

Quercetin (QT) was formulated into a novel self-emulsifying drug delivery system (SEDDS) to improve its oral bioavailability and antioxidant potential compared to free drug. Capmul MCM was selected as the oily phase on the basis of optimum solubility of QT in oil. Tween 20 and ethanol were selected.......8. The ratio of 40:40:20 w/w, Capmul MCM:QT (19:1)/Tween 20/ethanol was optimized based on its ability to form a spontaneous submicrometer emulsion in simulated gastrointestinal fluids. DPPH scavenging assay showed comparable antioxidant activity of QT-SEDDS to free QT. QT-SEDDS was robust in terms...

Piecewise linear emulator of the nonlinear Schroedinger equation and the resulting analytic solutions for Bose-Einstein condensates

International Nuclear Information System (INIS)

Theodorakis, Stavros

2003-01-01

We emulate the cubic term Ψ 3 in the nonlinear Schroedinger equation by a piecewise linear term, thus reducing the problem to a set of uncoupled linear inhomogeneous differential equations. The resulting analytic expressions constitute an excellent approximation to the exact solutions, as is explicitly shown in the case of the kink, the vortex, and a δ function trap. Such a piecewise linear emulation can be used for any differential equation where the only nonlinearity is a Ψ 3 one. In particular, it can be used for the nonlinear Schroedinger equation in the presence of harmonic traps, giving analytic Bose-Einstein condensate solutions that reproduce very accurately the numerically calculated ones in one, two, and three dimensions

Preparation of diesel emulsion using auxiliary emulsifier mono ethylene glycol and utilization in a turbocharged diesel engine

International Nuclear Information System (INIS)

Yilmaz, Emre; Solmaz, Hamit; Polat, Seyfi; Uyumaz, Ahmet; Şahin, Fatih; Salman, M. Sahir

2014-01-01

Highlights: • Mono-ethylene glycol was used as an auxiliary emulsifier. • Using mono ethylene glycol prolonged precipitation duration of emulsions. • With using E5 and E10 fuels engine torque averagely increased by 0.35% and 1.73% respectively. • It was found that specific fuel consumption of emulsions is lower than diesel. • Using E10 fuel reduced CO, NO x and soot emissions 44%, 47% and 5% respectively. - Abstract: Diesel engines are used widely as they have lower fuel consumption and higher thermal efficiency in transportation sector. However, the emitted high NO x , CO and soot emissions have led researchers to search different alternative fuels. At this point, diesel fuels emulsions help to reduce exhaust emissions. In this study, the effects of diesel fuel emulsions containing 5% (E5) and 10% (E10) water on engine performance an exhaust emissions has been investigated. Mono ethylene glycol was used as an auxiliary emulsifier in the preparation of the emulsion. Use of the mono ethylene glycol reduced the subsidence rate of the E5 and E10 about 34.5% and 47.1% respectively. The experiments were conducted at full load condition and at 2500, 3250 and 4000 rpm engine speeds. Engine torque and power increased according to diesel fuel between 2400 and 3600 engine speed range when emulsified fuels were used. But significant reductions were observed after that engine speed range. It was observed that the nitrogenoxide (NO x ) emission reduced 5.42% and 11.01% with using E5 and E10 fuel respectively according to diesel fuel at 2500 rpm. Also the soot emissions reduced 12.39% and 22.97% with using E5 and E10

De-emulsifiers for water-in-crude oil-emulsions

Energy Technology Data Exchange (ETDEWEB)

Zaki, N. [Egyptian Petroleum Research Inst. (EPRI), Cairo (Egypt); Al-Sabagh, A. [Egyptian Petroleum Research Inst. (EPRI), Cairo (Egypt)

1997-01-01

The efficiency of 18 different polyalkylphenols-polyalkylene-polyamines-formaldehyde ethoxylates (PAPAFE) in the deemulsification of water-in-crude oil-emulsion were studied. In this respect, two naturally occurring Egyptian water-in-curde oil-emulsions were used to test the investigated de-emulsifiers. The effect of the variation in the molecular structure of the (PAPAFE) on their de-emulsification potency is investigated. The investigation reveals that de-emulsifiers containing nonyl phenol reduce crude oil-water interfacial tension (IFT) and are more efficient than those containing dodecyl phenol. PAPAFE containing more amino groups are found to have better emulsion breaking ability. This is attributed to their enhanced ability to solubilize asphaltenes, which are the prime motivators for crude oil-water emulsion stability. They drag asphaltenes crosslinked at the water-crude oil interface and consequently, resulting in a substantial decrease in emulsion stability. There exists an optimum hydrophilic-lipophilic balance (HLB) for the investigated PAPAFE, ranging from 12 to 13.5 at which their maximum de-emulsification ability is attained. All studied PAPAFE showed increased de-emulsification performance by increasing the temperature from 50 to 70 C. Increasing the temperature reduces the viscosity of the crude oil continuous phase and increases the rate of diffusion of both the surfactant molecules and the dispersed water droplets. This will cause an increase in the rate of coalescence of the water droplets. (orig.) [Deutsch] Es wurde die Wirkung von 18 verschiedenen Polyalkylphenolpolyalkylenpolyamine-formaldehydethoxylaten (PAPAFE) bei der Demulgierung von Wasser-in-Rohoel-Emulsionen untersucht. Zwei in Aegypten natuerlich vorkommende Wasser-in-Rohoel-Emulsionen wurden fuer die Versuche eingesetzt, dabei wurde der Einfluss der molekularen Struktur der PAPAFEs auf das Demulgiervermoegen untersucht. Es zeigte sich, dass Demulgatoren mit Nonylphenol die

Real-Time Emulation of Heterogeneous Wireless Networks with End-to-Edge Quality of Service Guarantees: The AROMA Testbed

Directory of Open Access Journals (Sweden)

Anna Umbert

2010-01-01

Full Text Available This work presents and describes the real-time testbed for all-IP Beyond 3G (B3G heterogeneous wireless networks that has been developed in the framework of the European IST AROMA project. The main objective of the AROMA testbed is to provide a highly accurate and realistic framework where the performance of algorithms, policies, protocols, services, and applications for a complete heterogeneous wireless network can be fully assessed and evaluated before bringing them to a real system. The complexity of the interaction between all-IP B3G systems and user applications, while dealing with the Quality of Service (QoS concept, motivates the development of this kind of emulation platform where different solutions can be tested in realistic conditions that could not be achieved by means of simple offline simulations. This work provides an in-depth description of the AROMA testbed, emphasizing many interesting implementation details and lessons learned during the development of the tool that may result helpful to other researchers and system engineers in the development of similar emulation platforms. Several case studies are also presented in order to illustrate the full potential and capabilities of the presented emulation platform.

Causal knowledge and imitation/emulation switching in chimpanzees (Pan troglodytes) and children (Homo sapiens).

Science.gov (United States)

Horner, Victoria; Whiten, Andrew

2005-07-01

This study explored whether the tendency of chimpanzees and children to use emulation or imitation to solve a tool-using task was a response to the availability of causal information. Young wild-born chimpanzees from an African sanctuary and 3- to 4-year-old children observed a human demonstrator use a tool to retrieve a reward from a puzzle-box. The demonstration involved both causally relevant and irrelevant actions, and the box was presented in each of two conditions: opaque and clear. In the opaque condition, causal information about the effect of the tool inside the box was not available, and hence it was impossible to differentiate between the relevant and irrelevant parts of the demonstration. However, in the clear condition causal information was available, and subjects could potentially determine which actions were necessary. When chimpanzees were presented with the opaque box, they reproduced both the relevant and irrelevant actions, thus imitating the overall structure of the task. When the box was presented in the clear condition they instead ignored the irrelevant actions in favour of a more efficient, emulative technique. These results suggest that emulation is the favoured strategy of chimpanzees when sufficient causal information is available. However, if such information is not available, chimpanzees are prone to employ a more comprehensive copy of an observed action. In contrast to the chimpanzees, children employed imitation to solve the task in both conditions, at the expense of efficiency. We suggest that the difference in performance of chimpanzees and children may be due to a greater susceptibility of children to cultural conventions, perhaps combined with a differential focus on the results, actions and goals of the demonstrator.

Chemical and physical characteristics of local lecithin in comparison with some other food emulsifiers

Directory of Open Access Journals (Sweden)

El-Shattory, Y.

1999-08-01

Full Text Available The chemical and physical characteristics of local lecithin and other food emulsifiers (Emulfuid E, Triodan R 90, Panodan 150 and Glycerol mono stéarate were studied. The characteristics of these emulsifiers studied were solubility, hydrophile-lipophile balance (HLB, stability index (SI, fatty acid composition and infrared spectrum. The results obtained showed that Emulfuid E and local lecithin were mixture of lecithins and phosphatidyl ethanol-amine. In addition, Triodan R 90 was a polyglycerol ester of ricinoleic acid, Panodan 150 was a blend of mono and diglycerides, and G.M.S. was a monoglycerol ester of stearic acid.

Se estudiaron las características químicas y físicas de lecitina local y otros emulsionantes alimentarios (Emulfuid E, Triodan R 90, Panodan 150 y Monoestearato de glicerol. Las características de estos emulsionantes estudiados fueron solubilidad, balance hidrófilo-lipófilo (HLB, índice de estabilidad (SI, composición en ácidos grasos y espectros de infrarrojo. Los resultados obtenidos mostraron que Emulfuid E y lecitina local fueron mezclas de lecitinas y fosfatidil etanolamina. Por otro lado, Triodan R 90 fue ester poliglicerídico del ácido ricinoleico, Panodan 150 una mezcla de mono y diglicéridos y G.M.S. un éster monoglicerídico del ácido esteárico.

A comparative study on the emulsifying properties of various species of gum tragacanth.

Science.gov (United States)

Farzi, Mina; Emam-Djomeh, Zahra; Mohammadifar, Mohammad Amin

2013-06-01

Emulsification activities of three different species of gum tragacanth containing Astragalus gossypinus, A. compactus and A. rahensis were investigated. Emulsion stability indexes, particle size distributions, steady and unsteady rheological properties and some other physicochemical attributes including the surface tensions and uronic acid contents were taken into consideration. It was revealed that A. gossypinus created the most stable emulsions although having lower viscosity than A. compactus. It is believed that higher insoluble fraction and higher uronic content made this species a good steric and electrostatic emulsifier. Copyright © 2013 Elsevier B.V. All rights reserved.

FPGAs Emulate Microprocessors-A Successful Case for HFC NPP Digital I and C Upgrade

International Nuclear Information System (INIS)

Hsu, Allen; Crow, Ivan; Reese, Carl; Kim, Jong; Yang, Steve

2014-01-01

Field Programmable Gate Arrays (FPGAs), as programmable logic devices (PLDs) have gained a great deal of interests for implementing safety I and C applications in nuclear power plants (NPPs) largely owing to the FPGAs'potential advantage over the currently more common microprocessor-based digital I and C applications. First of all, FPGAs have adequate capabilities for most digital I and C applications in NPPs. Secondly, FPGAs provide products with longer lifetime, improve testability, and reduce the drift which occurs in analog-based systems, from hardware perspective. Thirdly, FPGAs, from software perspective, can be made simpler, less reliant on complex software such as operating systems, which should make FPGAs easier to qualify for nuclear safety applications. Fourthly, FPGAs are less vulnerable to cyber attacks when FPGAs implement the I and C systems that do not contain high-level, general purpose software that may be easily subjected to malicious modifications. Finally, FPGAs can bring cost reduction in an I and C digital upgrade because FPGAs can provide simpler licensing process than microprocessor-based digital I and C, and FPGAs can be implemented more efficiently. This paper will present one successful case for YGN Unit I and C upgrade using FPGA-based components to replace the obsolete Intel 8085 Microprocessor-based controllers. In this case, FPGAs emulated the process of the existing microprocessors and interpreted the execution of CPU processing. More than 160 of the FPGA-based SBC-01 controllers replacing the Intel 8085 Microprocessor-based Printed Circuit Boards have been installed and running successfully for safety I and C applications over the last five years. In this upgrade, the new FPGA-based controller board SBC-01 emulated the functions of Intel 8085 microprocessor correctly. It is a successful and cost-effective upgrade.vIn this paper, lifecycle design and implementation process and rigorous V and V activities that were used in the

FPGAs Emulate Microprocessors-A Successful Case for HFC NPP Digital I and C Upgrade

Energy Technology Data Exchange (ETDEWEB)

Hsu, Allen; Crow, Ivan; Reese, Carl; Kim, Jong; Yang, Steve [Doosan HF Controls Corp, Carrollton (United States)

2014-08-15

Field Programmable Gate Arrays (FPGAs), as programmable logic devices (PLDs) have gained a great deal of interests for implementing safety I and C applications in nuclear power plants (NPPs) largely owing to the FPGAs'potential advantage over the currently more common microprocessor-based digital I and C applications. First of all, FPGAs have adequate capabilities for most digital I and C applications in NPPs. Secondly, FPGAs provide products with longer lifetime, improve testability, and reduce the drift which occurs in analog-based systems, from hardware perspective. Thirdly, FPGAs, from software perspective, can be made simpler, less reliant on complex software such as operating systems, which should make FPGAs easier to qualify for nuclear safety applications. Fourthly, FPGAs are less vulnerable to cyber attacks when FPGAs implement the I and C systems that do not contain high-level, general purpose software that may be easily subjected to malicious modifications. Finally, FPGAs can bring cost reduction in an I and C digital upgrade because FPGAs can provide simpler licensing process than microprocessor-based digital I and C, and FPGAs can be implemented more efficiently. This paper will present one successful case for YGN Unit I and C upgrade using FPGA-based components to replace the obsolete Intel 8085 Microprocessor-based controllers. In this case, FPGAs emulated the process of the existing microprocessors and interpreted the execution of CPU processing. More than 160 of the FPGA-based SBC-01 controllers replacing the Intel 8085 Microprocessor-based Printed Circuit Boards have been installed and running successfully for safety I and C applications over the last five years. In this upgrade, the new FPGA-based controller board SBC-01 emulated the functions of Intel 8085 microprocessor correctly. It is a successful and cost-effective upgrade.vIn this paper, lifecycle design and implementation process and rigorous V and V activities that were used in the

Development of adaptive core emulator for PMS-XRBP of CE type plant

International Nuclear Information System (INIS)

Song, Jae Seung; Zee, Sung Quun; Lee, Chung Chan; Lee, Ki Bog; Rhy, Hyo Sang; Chang, Jong Hwa; Lee, Young Ouk; Baek, Seung Min; Seo, Ho Joon.

1996-12-01

The purpose of this report is to develop ONED-based adaptive core emulator (ACE) for Korean Standard Nuclear Power Plant. This report is first year report and includes 1) augmentation of ONED94 I/O system 2) non-equilibrium xenon initialization for core transient simulation 3) ONED94 verification via plant measurements 4) automatic data link system from PMS and personal computer. (author). 4 tabs., 4 figs., 8 refs

Development of adaptive core emulator for PMS-XRBP of CE type plant

Energy Technology Data Exchange (ETDEWEB)

Song, Jae Seung; Zee, Sung Quun; Lee, Chung Chan; Lee, Ki Bog; Rhy, Hyo Sang; Chang, Jong Hwa; Lee, Young Ouk; Baek, Seung Min; Seo, Ho Joon

1996-12-01

The purpose of this report is to develop ONED-based adaptive core emulator (ACE) for Korean Standard Nuclear Power Plant. This report is first year report and includes (1) augmentation of ONED94 I/O system (2) non-equilibrium xenon initialization for core transient simulation (3) ONED94 verification via plant measurements (4) automatic data link system from PMS and personal computer. (author). 4 tabs., 4 figs., 8 refs.

Treatment of emulsified oils by electrocoagulation: pulsed voltage applications.

Science.gov (United States)

Genc, Ayten; Bakirci, Busra

2015-01-01

The effect of pulsed voltage application on energy consumption during electrocoagulation was investigated. Three voltage profiles having the same arithmetic average with respect to time were applied to the electrodes. The specific energy consumption for these profiles were evaluated and analyzed together with oil removal efficiencies. The effects of applied voltages, electrode materials, electrode configurations, and pH on oil removal efficiency were determined. Electrocoagulation experiments were performed by using synthetic and real wastewater samples. The pulsed voltages saved energy during the electrocoagulation process. In continuous operation, energy saving was as high as 48%. Aluminum electrodes used for the treatment of emulsified oils resulted in higher oil removal efficiencies in comparison with stainless steel and iron electrodes. When the electrodes gap was less than 1 cm, higher oil removal efficiencies were obtained. The highest oil removal efficiencies were 95% and 35% for the batch and continuous operating modes, respectively.

Emulating Wired Backhaul with Wireless Network Coding

DEFF Research Database (Denmark)

Thomsen, Henning; De Carvalho, Elisabeth; Popovski, Petar

2014-01-01

In this paper we address the need for wireless network densification. We propose a solution wherein the wired backhaul employed in heterogeneous cellular networks is replaced with wireless links, while maintaining the rate requirements of the uplink and downlink traffic of each user. The first...... of the two-way protocol. The transmit power is set high enough to enable successive decoding at the small cell base station where the downlink data to the user is first decoded and its contribution removed from the received signal followed by the uplink data from the user. The decoding of the second layer......, the uplink traffic to the user, remains identical to the one performed in a wired system. In the broadcast phase, the decoding of the downlink traffic can also be guaranteed to remain identical. Hence, our solution claims an emulation of a wired backhaul with wireless network coding with same performance. We...

Generic inertia emulation controller for multi-terminal voltage-source-converter high voltage direct current systems

DEFF Research Database (Denmark)

Zhu, Jiebei; Guerrero, Josep M.; Hung, William

2014-01-01

A generic Inertia Emulation Controller (INEC) scheme for Multi-Terminal Voltage-Source-Converter based HVDC (VSC-MTDC) systems is proposed and presented in this paper. The proposed INEC can be incorporated in any Grid-side Voltage-Source-Converter (GVSC) station, allowing the MTDC terminal...

Space Link Extension (SLE) Emulation for High-Throughput Network Communication

Science.gov (United States)

Murawski, Robert W.; Tchorowski, Nicole; Golden, Bert

2014-01-01

As the data rate requirements for space communications increases, significant stress is placed not only on the wireless satellite communication links, but also on the ground networks which forward data from end-users to remote ground stations. These wide area network (WAN) connections add delay and jitter to the end-to-end satellite communication link, effects which can have significant impacts on the wireless communication link. It is imperative that any ground communication protocol can react to these effects such that the ground network does not become a bottleneck in the communication path to the satellite. In this paper, we present our SCENIC Emulation Lab testbed which was developed to test the CCSDS SLE protocol implementations proposed for use on future NASA communication networks. Our results show that in the presence of realistic levels of network delay, high-throughput SLE communication links can experience significant data rate throttling. Based on our observations, we present some insight into why this data throttling happens, and trace the probable issue back to non-optimal blocking communication which is sup-ported by the CCSDS SLE API recommended practices. These issues were presented as well to the SLE implementation developers which, based on our reports, developed a new release for SLE which we show fixes the SLE blocking issue and greatly improves the protocol throughput. In this paper, we also discuss future developments for our end-to-end emulation lab and how these improvements can be used to develop and test future space communication technologies.

Laboratory evaluation of the emulsifying characteristics of pumps

Energy Technology Data Exchange (ETDEWEB)

Harvey, A.C.; Guzdar, A.R.; Friswell, D.R.

1973-10-01

The program was devoted to a laboratory investigation of the emulsifying characteristics of different pumps suitable for shipboard pumping of bilge and ballast water oily wastes. The tests were designed to investigate the effect of several parameters, such as oil type, input oil concentration, detergent, pump operating characteristics (pressure and flow rate), and salt vs. fresh water, on emulsification. Tests were conducted on the Foster-Miller test loop. No. 2 fuel oil, lubricating oil and No. 6 fuel oil were the oils tested at concentrations ranging from 1 to 10%. The oils were tested with and without the addition of 10% Gamlen D surfactant. The pumps used were a Parker Diaphragm pump, a Blackmer Sliding Vane pump, an Ingersoll Rand Centrifugal pump, and a Deming Centrifugal pump. Pump pressure ranged from 10 to 60 psi and flow rates from 10 to 100 gpm. A total of 270 tests was conducted covering 198 different operating points, 108 concerning pump comparison, 54 concerning oil concentration and surfactant, and 45 concerning salt water.

Combining super-ensembles and statistical emulation to improve a regional climate and vegetation model

Science.gov (United States)

Hawkins, L. R.; Rupp, D. E.; Li, S.; Sarah, S.; McNeall, D. J.; Mote, P.; Betts, R. A.; Wallom, D.

2017-12-01

Changing regional patterns of surface temperature, precipitation, and humidity may cause ecosystem-scale changes in vegetation, altering the distribution of trees, shrubs, and grasses. A changing vegetation distribution, in turn, alters the albedo, latent heat flux, and carbon exchanged with the atmosphere with resulting feedbacks onto the regional climate. However, a wide range of earth-system processes that affect the carbon, energy, and hydrologic cycles occur at sub grid scales in climate models and must be parameterized. The appropriate parameter values in such parameterizations are often poorly constrained, leading to uncertainty in predictions of how the ecosystem will respond to changes in forcing. To better understand the sensitivity of regional climate to parameter selection and to improve regional climate and vegetation simulations, we used a large perturbed physics ensemble and a suite of statistical emulators. We dynamically downscaled a super-ensemble (multiple parameter sets and multiple initial conditions) of global climate simulations using a 25-km resolution regional climate model HadRM3p with the land-surface scheme MOSES2 and dynamic vegetation module TRIFFID. We simultaneously perturbed land surface parameters relating to the exchange of carbon, water, and energy between the land surface and atmosphere in a large super-ensemble of regional climate simulations over the western US. Statistical emulation was used as a computationally cost-effective tool to explore uncertainties in interactions. Regions of parameter space that did not satisfy observational constraints were eliminated and an ensemble of parameter sets that reduce regional biases and span a range of plausible interactions among earth system processes were selected. This study demonstrated that by combining super-ensemble simulations with statistical emulation, simulations of regional climate could be improved while simultaneously accounting for a range of plausible land

Characterization of a Prototype Radio Frequency Space Environment Path Emulator for Evaluating Spacecraft Ranging Hardware

Science.gov (United States)

Mitchell, Jason W.; Baldwin, Philip J.; Kurichh, Rishi; Naasz, Bo J.; Luquette, Richard J.

2007-01-01

The Formation Flying Testbed (FFTB) at the National Aeronautics and Space Administration (NASA) Goddard Space Flight Center (GSFC) provides a hardware-in-the-loop test environment for formation navigation and control. The facility is evolving as a modular, hybrid, dynamic simulation facility for end-to-end guidance, navigation and control (GN&C) design and analysis of formation flying spacecraft. The core capabilities of the FFTB, as a platform for testing critical hardware and software algorithms in-the-loop, have expanded to include S-band Radio Frequency (RF) modems for interspacecraft communication and ranging. To enable realistic simulations that require RF ranging sensors for relative navigation, a mechanism is needed to buffer the RF signals exchanged between spacecraft that accurately emulates the dynamic environment through which the RF signals travel, including the effects of the medium, moving platforms, and radiated power. The Path Emulator for Radio Frequency Signals (PERFS), currently under development at NASA GSFC, provides this capability. The function and performance of a prototype device are presented.

An adaptive tuned mass damper based on the emulation of positive and negative stiffness with an MR damper

International Nuclear Information System (INIS)

Weber, F; Boston, C; Maślanka, M

2011-01-01

This paper presents a new adaptive tuned mass damper (TMD) whose stiffness and damping can be tuned in real-time to changing frequencies of a target structure. The adaptive TMD consists of a tuned mass, a tuned passive spring and a magnetorheological (MR) damper. The MR damper is used to emulate controlled friction–viscous damping and controlled stiffness. The controlled positive or negative stiffness emulated by the MR damper works in parallel to the stiffness of the passive TMD spring. The resulting overall TMD stiffness can therefore be varied around the passive spring stiffness using the MR damper. Both the emulated stiffness and friction–viscous damping in the MR damper are controlled such that the resulting overall TMD stiffness and damping are adjusted according to Den Hartog's formulae. Simulations demonstrate that the adaptive TMD with a controlled MR damper provides the same reduction of steady state vibration amplitudes in the target structure as a passive TMD if the target structure vibrates at the nominal frequency. However, if the target structure vibrates at different frequencies, e.g. due to changed service loads, the adaptive TMD with a controlled MR damper outperforms the passive TMD by up to several 100% depending on the frequency change

Multi-level emulation of a volcanic ash transport and dispersion model to quantify sensitivity to uncertain parameters

Science.gov (United States)

Harvey, Natalie J.; Huntley, Nathan; Dacre, Helen F.; Goldstein, Michael; Thomson, David; Webster, Helen

2018-01-01

Following the disruption to European airspace caused by the eruption of Eyjafjallajökull in 2010 there has been a move towards producing quantitative predictions of volcanic ash concentration using volcanic ash transport and dispersion simulators. However, there is no formal framework for determining the uncertainties of these predictions and performing many simulations using these complex models is computationally expensive. In this paper a Bayesian linear emulation approach is applied to the Numerical Atmospheric-dispersion Modelling Environment (NAME) to better understand the influence of source and internal model parameters on the simulator output. Emulation is a statistical method for predicting the output of a computer simulator at new parameter choices without actually running the simulator. A multi-level emulation approach is applied using two configurations of NAME with different numbers of model particles. Information from many evaluations of the computationally faster configuration is combined with results from relatively few evaluations of the slower, more accurate, configuration. This approach is effective when it is not possible to run the accurate simulator many times and when there is also little prior knowledge about the influence of parameters. The approach is applied to the mean ash column loading in 75 geographical regions on 14 May 2010. Through this analysis it has been found that the parameters that contribute the most to the output uncertainty are initial plume rise height, mass eruption rate, free tropospheric turbulence levels and precipitation threshold for wet deposition. This information can be used to inform future model development and observational campaigns and routine monitoring. The analysis presented here suggests the need for further observational and theoretical research into parameterisation of atmospheric turbulence. Furthermore it can also be used to inform the most important parameter perturbations for a small operational

Advances in the generation of a new emulsified fuel

Energy Technology Data Exchange (ETDEWEB)

Chavez, A. [Technical Consultancy, Energy Plus UC, Huitzilac, Morelos (Mexico); Ramirez, M. [Instituto Mexicano del Petroleo, Programa de Aseguramiento de Hidrocarburos, Mexico, D.F. (Mexico); Medina, E. [Universidad Nacional Autonoma de Mexico, Departamento de Termofluidos, Facultad de Ingenieria, Mexico, D.F. (Mexico); Bolado, R.; Mora, J. [Instituto Mexicano del Petroleo, Laboratorio de Combustion, Veracruz (Mexico)

2011-08-15

The development of a new emulsified fuel is described, from the conceptual idea to the semi-industrial tests of the final product. The starting point was the necessity to lower the particulate matter (PM) emissions produced by the combustion of more than 200 MBD of heavy fuel oil (HFO) used for electric power conversion. The major component of HFO is a vacuum residue of the oil refining process mixed with light cycle oils to make it pumpable. An alternative to handle and burn the high viscosity residue (solid at room temperature) is by converting it in an oil-in-water emulsion. The best emulsions resulted of 70% residue in 30% water, Sauter Mean Diameter of 10-20 {mu}m and a stability of more than 90 days. Spray burning tests of the emulsion against HFO in a semi-industrial 500 kW furnace showed a reduction in PM emissions of 24-36%. (orig.)

Solubility of ocular therapeutic agents in self-emulsifying oils. I. Self-emulsifying oils for ocular drug delivery: solubility of indomethacin, aciclovir and hydrocortisone.

Science.gov (United States)

Czajkowska-Kośnik, Anna; Sznitowska, Małgorzata

2009-01-01

Self-emulsifying drug delivery systems (SEDDS) were prepared by dissolving Cremophor EL, Tween 20, Tween 80 and Span 80 (1% or 5%) in oils (Miglyol 812 or castor oil). Solubilities of three ophthalmic drugs, namely aciclovir, hydrocortisone and indomethacin were determined in these systems. In addition, the effect of a small amount of water (0.5% and 2%) on solubilization properties of the systems was estimated. Of the three substances, indomethacin showed the best solubility in Miglyol while aciclovir was practically insoluble in this oil. The surfactants usually increased drug solubility in the oily phase. Only Tween 20 was found to decrease the solubility of aciclovir and hydrocortisone in Miglyol. Addition of a small amount of water to the oil/surfactant system increased solubility of hydrocortisone, but not of indomethacin. The results of the current study may be utilized to design a suitable composition of SEDDS and allow continuation of research on this type of drug carriers.

Emulsifier-free emulsion polymerization produces highly charged, monodisperse particles for near infrared photonic crystals.

Science.gov (United States)

Reese, Chad E; Asher, Sanford A

2002-04-01

We have developed emulsifier-free, emulsion polymerization recipes for the synthesis of highly charged, monodisperse latex particles of diameters between 500 and 1100 nm. These latexes consist of poly[styrene-(co-2-hydroxyethyl methacrylate)] spherical particles whose surfaces are functionalized with sulfate and carboxylic acid groups. These highly charged, monodisperse particles readily self-assemble into robust, three-dimensionally ordered crystalline colloidal array photonic crystals that Bragg diffract light in the near infrared spectral region. By altering the particle number density, the diffraction wavelength can be tuned from approximately 1000 to approximately 4000 nm.

Emulation of recharge and evapotranspiration processes in shallow groundwater systems

Science.gov (United States)

Doble, Rebecca C.; Pickett, Trevor; Crosbie, Russell S.; Morgan, Leanne K.; Turnadge, Chris; Davies, Phil J.

2017-12-01

In shallow groundwater systems, recharge and evapotranspiration are highly sensitive to changes in the depth to water table. To effectively model these fluxes, complex functions that include soil and vegetation properties are often required. Model emulation (surrogate modelling or meta-modelling) can provide a means of incorporating detailed conceptualisation of recharge and evapotranspiration processes, while maintaining the numerical tractability and computational performance required for regional scale groundwater models and uncertainty analysis. A method for emulating recharge and evapotranspiration processes in groundwater flow models was developed, and applied to the South East region of South Australia and western Victoria, which is characterised by shallow groundwater, wetlands and coastal lakes. The soil-vegetation-atmosphere transfer (SVAT) model WAVES was used to generate relationships between net recharge (diffuse recharge minus evapotranspiration from groundwater) and depth to water table for different combinations of climate, soil and land cover types. These relationships, which mimicked previously described soil, vegetation and groundwater behaviour, were combined into a net recharge lookup table. The segmented evapotranspiration package in MODFLOW was adapted to select values of net recharge from the lookup table depending on groundwater depth, and the climate, soil and land use characteristics of each cell. The model was found to be numerically robust in steady state testing, had no major increase in run time, and would be more efficient than tightly-coupled modelling approaches. It made reasonable predictions of net recharge and groundwater head compared with remotely sensed estimates of net recharge and a standard MODFLOW comparison model. In particular, the method was better able to predict net recharge and groundwater head in areas with steep hydraulic gradients.

Synergistic Combinations of a Pyrethroid Insecticide and an Emulsifiable Oil Formulation of Beauveria bassiana to Overcome Insecticide Resistance in Listronotus maculicollis (Coleoptera: Curculionidae).

Science.gov (United States)

Wu, Shaohui; Kostromytska, Olga S; Koppenhöfer, Albrecht M

2017-08-01

The annual bluegrass weevil, Listronotus maculicollis (Kirby), is a major pest of golf course turf in eastern North America and has become particularly problematic owing to widespread development of insecticide resistance. As an alternative option to manage resistant adult L. maculicollis, we explored combinations of the pyrethroid insecticide bifenthrin with an emulsifiable oil formulation of the entomopathogenic fungus Beauveria bassiana strain GHA (Bb ES). Combinations synergistically enhanced mortality in both insecticide-susceptible and insecticide-resistant L. maculicollis adults in the laboratory when bifenthrin was used at LC50s for each population. To determine the component behind the synergism, technical spores of B. bassiana GHA and the emulsifiable oil carrier in the fungal formulation were tested separately or in combination with bifenthrin. In both separate and combined applications, the emulsifiable oil carrier was responsible for high mortality within 3 d after treatment and interacted synergistically with bifenthrin, whereas fungus-induced mortality started later. Strong synergism was also observed in three field experiments with a relatively resistant L. maculicollis population. Combinations of Bb ES and bifenthrin hold promise as an effective L. maculicollis management tool, particularly of pyrethroid-resistant populations. © The Authors 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

A state space approach to the emulator-based GPC design

DEFF Research Database (Denmark)

Jensen, Morten Rostgaard; Lauritsen, Morten Bach; Poulsen, Niels Kjølstad

1996-01-01

in models and designs based on the delta-operator. The GPC controller is interesting since it is a controller that successfully has been applied to many industrial process during the last decade. The present paper discusses an emulator-based GPC, a controller design intended for fast sampled adaptive......For sampled dynamical systems the delta-operator is an appealing alternative to the conventional shift operator since at rapid sampling rates it shows better numerical properties and a closer rapprochement to the continuous-time description. Thus, the structural information is easy to interpret...... control systems where the conventional q-based techniques fail due to poor word-length characteristics....

Programming a Detector Emulator on NI's FlexRIO Platform

Science.gov (United States)

Gervais, Michelle; Crawford, Christopher; Sprow, Aaron; Nab Collaboration

2017-09-01

Recently digital detector emulators have been on the rise as a means to test data acquisition systems and analysis toolkits from a well understood data set. National Instruments' PXIe-7962R FPGA module and Active Technologies AT-1212 DAC module provide a customizable platform for analog output. Using a graphical programming language, we have developed a system capable of producing two time-correlated channels of analog output which sample unique amplitude spectra to mimic nuclear physics experiments. This system will be used to model the Nab experiment, in which a prompt beta decay electron is followed by a slow proton according to a defined time distribution. We will present the results of our work and discuss further development potential. DOE under Contract DE-SC0008107.

Effect of emulsifier type and concentration, aqueous phase volume and wax ratio on physical, material and mechanical properties of water in oil lipsticks.

Science.gov (United States)

Beri, A; Norton, J E; Norton, I T

2013-12-01

Water-in-oil emulsions in lipsticks could have the potential to improve moisturizing properties and deliver hydrophilic molecules to the lips. The aims of this work were (i) to investigate the effect of emulsifier type (polymer vs. monomer, and saturated vs. unsaturated chain) and concentration on droplet size and (ii) to investigate the effect of wax ratio (carnauba wax, microcrystalline wax, paraffin wax and performalene) and aqueous phase volume on material properties (Young's modulus, point of fracture, elastic modulus and viscous modulus). Emulsion formation was achieved using a high shear mixer. Results showed that the saturated nature of the emulsifier had very little effect on droplet size, neither did the use of an emulsifier with a larger head group (droplet size ~18-25 μm). Polyglycerol polyricinoleate (PGPR) resulted in emulsions with the smallest droplets (~3-5 μm), as expected from previous studies that show that it produces a thick elastic interface. The results also showed that both Young's modulus and point of fracture increase with increasing percentage of carnauba wax (following a power law dependency of 3), but decrease with increasing percentage of microcrystalline wax, suggesting that the carnauba wax is included in the overall wax network formed by the saturated components, whereas the microcrystalline wax forms irregular crystals that disrupt the overall wax crystal network. Young's modulus, elastic modulus and viscous modulus all decrease with increasing aqueous phase volume in the emulsions, although the slope of the decrease in elastic and viscous moduli is dependent on the addition of solid wax, as a result of strengthening the network. This work suggests the potential use for emulsions in lipstick applications, particularly when PGPR is used as an emulsifier, and with the addition of solid wax, as it increases network strength. © 2013 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

PREPARATION AND EVALUATION OF VITAMIN E ADJUVANTED OIL EMULSIFIED INFECTIOUS BRONCHITIS EXPERIMENTAL VACCINE

Directory of Open Access Journals (Sweden)

S. ALI, M. ARSHAD, M. SIDDIQUE AND M. ASHRAF

2007-10-01

Full Text Available The present study was conducted to prepare oil emulsified (OE infectious bronchitis (IB experimental vaccines. The vaccines were prepared using the vaccinal strain H-120 Infectious Bonchitis virus (IBV. The virus was cultivated in 9-day old embryonated eggs via allantoic cavity route. Allantoic-amniotic fluid (AAF was collected and inactivated with formalin @ 0.12%. Water in oil emulsion was prepared by adding one part of AAF to four parts of mineral oil containing water phase (Tween 80 and oil phase (Span 80 surfactants. Hydrophile lypohile balance (HLB of the emulsion was maintained at 7.0. Two oil emulsified experimental vaccines were prepared. Vaccine-I was prepared without vitamin E and Vaccine-II with vitamin E (300 mg/ml. A total of 120 day-old broiler breeder chickens were divided into 4 groups, A, B, C, and D, each having 30 birds. At the age of 21 days, experimental Vaccine-I, experimental vaccine-II and commercial IB killed (H-120 vaccine were inoculated @ 0.5 ml in the birds of groups A, B and C, respectively. Group D was maintained as nonvaccinated control. Efficacy of the vaccines was evaluated on the basis of humoral immune response (haemagglutination inhibition antibody titres against IB in the four groups. The seven weeks cumulative mean antibody titres (CMT of each group were calculated. The highest CMT was observed in group B (130, followed by group C (69, group A (58 and group D (17. Statistical analysis showed that haemagglutination inhibition (HI antibody titres in group B (vaccine- II were significantly higher than those of groups A, B and C (P< 0.05.

Influence of different degrees of bilateral emulated contractures at the triceps surae on gait kinematics: The difference between gastrocnemius and soleus.

Science.gov (United States)

Attias, M; Bonnefoy-Mazure, A; De Coulon, G; Cheze, L; Armand, S

2017-10-01

Ankle plantarflexion contracture results from a permanent shortening of the muscle-tendon complex. It often leads to gait alterations. The objective of this study was to compare the kinematic adaptations of different degrees of contractures and between isolated bilateral gastrocnemius and soleus emulated contractures using an exoskeleton. Eight combinations of contractures were emulated bilaterally on 10 asymptomatic participants using an exoskeleton that was able to emulate different degrees of contracture of gastrocnemius (biarticular muscle) and soleus (monoarticular muscle), corresponding at 0°, 10°, 20°, and 30° ankle plantarflexion contracture (knee-flexed and knee-extended). Range of motion was limited by ropes attached for soleus on heel and below the knee and for gastrocnemius on heel and above the knee. A gait analysis session was performed to evaluate the effect of these different emulated contractures on the Gait Profile Score, walking speed and gait kinematics. Gastrocnemius and soleus contractures influence gait kinematics, with an increase of the Gait Profile Score. Significant differences were found in the kinematics of the ankles, knees and hips. Contractures of soleus cause a more important decrease in the range of motion at the ankle than the same degree of gastrocnemius contractures. Gastrocnemius contractures cause greater knee flexion (during the stance phase) and hip flexion (during all the gait cycle) than the same level of soleus contractures. These results can support the interpretation of the Clinical Gait Analysis data by providing a better understanding of the effect of isolate contracture of soleus and gastrocnemius on gait kinematics. Copyright © 2017 Elsevier B.V. All rights reserved.

Accumulation of operational history through emulation test to meet proven technology requirement for newly developed I and C technology

International Nuclear Information System (INIS)

Yeong Cheol, Shin; Sung Kon, Kang; Han Seong, Son

2006-01-01

As new advanced digital I and C technology with potential benefits of higher functionality and better cost effectiveness is available in the market, NPP (Nuclear Power Plant) operators are inclined to use the new technology for the construction of new plant and the upgrade of existing plants. However, this new technology poses risks to the NPP operators at the same time. These risks are mainly due to the poor reliability of newly developed technology. KHNP's past experiences with the new equipment shows many cases of reliability problems. And their consequences include unintended plant trips, lowered acceptance of the new digital technology by the plant I and C maintenance crew, and increased licensing burden in answering for questions from the nuclear regulatory body. Considering the fact that the risk of these failures in the nuclear plant operation is far greater than those in other industry, nuclear power plant operators want proven technology for I and C systems. This paper presents an approach for the emulation of operational history through which a newly developed technology becomes a proven technology. One of the essential elements of this approach is the feedback scheme of running the new equipment in emulated environment, gathering equipment failure, and correcting the design(and test bed). The emulation of environment includes normal and abnormal events of the new equipment such as reconfiguration of control system due to power failure, plant operation including full spectrum of credible scenarios in an NPP. Emulation of I and C equipment execution mode includes normal operation, initialization and termination, abnormal operation, hardware maintenance and maintenance of algorithm/software. Plant specific simulator is used to create complete profile of plant operational conditions that I and C equipment is to experience in the real plant. Virtual operating crew technology is developed to run the simulator scenarios without involvement of actual operators

Fat reduction and alternatives for its substitution un emulsified meat products, a review

Directory of Open Access Journals (Sweden)

Irma Natalia Rivera Ruiz

2012-06-01

Full Text Available Animal fat employed in emulsified meat products elaboration is important for the flavor and texture characteristics. Nonetheless, the association of this kind of saturated fats with cardiovascular disease is a negative factor against their consumption. Different alternatives had been studied to reduce their content, replacing the fat with water, hydrocolloids, gums, proteins and/or vegetable oils. This modifies the meat products functional properties like yield, cocking stability and water retention, affecting moisture content and oxidative rancidity, texture and color. All these alternatives had advantages and disadvantages in their use and application, but the particular needs will determinate the optimum formulation for healthier meat products.

Asynchronous transfer mode and Local Area Network emulation standards, protocols, and security implications

OpenAIRE

Kirwin, John P.

1999-01-01

A complex networking technology called Asynchronous Transfer Mode (ATM) and a networking protocol called Local Area Network Emulation (LANE) are being integrated into many naval networks without any security-driven naval configuration guidelines. No single publication is available that describes security issues of data delivery and signaling relating to the transition of Ethernet to LANE and ATM. The thesis' focus is to provide: (1) an overview and security analysis of standardized protocols ...

The introspective may achieve more: Enhancing existing Geoscientific models with native-language emulated structural reflection

Science.gov (United States)

Ji, Xinye; Shen, Chaopeng

2018-01-01

Geoscientific models manage myriad and increasingly complex data structures as trans-disciplinary models are integrated. They often incur significant redundancy with cross-cutting tasks. Reflection, the ability of a program to inspect and modify its structure and behavior at runtime, is known as a powerful tool to improve code reusability, abstraction, and separation of concerns. Reflection is rarely adopted in high-performance Geoscientific models, especially with Fortran, where it was previously deemed implausible. Practical constraints of language and legacy often limit us to feather-weight, native-language solutions. We demonstrate the usefulness of a structural-reflection-emulating, dynamically-linked metaObjects, gd. We show real-world examples including data structure self-assembly, effortless input/output (IO) and upgrade to parallel I/O, recursive actions and batch operations. We share gd and a derived module that reproduces MATLAB-like structure in Fortran and C++. We suggest that both a gd representation and a Fortran-native representation are maintained to access the data, each for separate purposes. Embracing emulated reflection allows generically-written codes that are highly re-usable across projects.

Estabilidade de emulsões de d-limoneno em quitosana modificada Stability of d-limonene emulsions in modified chitosan

Directory of Open Access Journals (Sweden)

Camila Figueiredo Borgognoni

2006-09-01

Full Text Available A quitosana é um biopolímero produzido a partir da quitina, presente na casca de crustáceos. Atualmente, o estudo de suas propriedades se deve às suas diversas utilizações nas áreas farmacêutica e alimentícia. A quitosana utilizada neste estudo foi quimicamente modificada para tornar-se solúvel em água (quitosana succinilada. Estudou-se a estabilidade de emulsões com d-limoneno para que estes dados sejam úteis na sua posterior utilização como agente de encapsulação de d-limoneno por liofilização. Sua estabilidade foi analisada por espectrofotometria, em diferentes temperaturas, e por cromatografia gasosa associada à técnica da análise do espaço livre, à temperatura ambiente. Sua caracterização foi feita por microscopia óptica. Emulsões de maltodextrina com d-limoneno foram utilizadas para comparação já que maltodextrinas são muito usadas como agentes de encapsulação de aromas. Observou-se boa estabilidade de emulsões de quitosana succinilada com d-limoneno ao longo do tempo e características muito distintas em relação às observadas em emulsões de maltodextrina com d-limoneno. Pode-se concluir neste estudo que emulsões de quitosana succinilada com d-limoneno apresentaram características favoráveis à encapsulação de aromas.Chitosan is a biopolymer derived from chitin, a component of the shells of crustaceans. Recently, special attention has been given to the study of chitosan properties as a consequence of their wide application in pharmaceutical and food areas. In this study, the chitosan used was chemically modified in order to become water soluble (succinyl chitosan. The stability of succinyl chitosan emulsion with d-limonene was studied so that these results could be useful in a subsequent use of succinyl chitosan as a d-limonene encapsulating agent by lyophilization. The stability of the emulsion was analyzed using a spectrophotometer in different temperatures and by the headspace

Effects of Emulsifier, Overrun and Dasher Speed on Ice Cream Microstructure and Melting Properties.

Science.gov (United States)

Warren, Maya M; Hartel, Richard W

2018-03-01

Ice cream is a multiphase frozen food containing ice crystals, air cells, fat globules, and partially coalesced fat globule clusters dispersed in an unfrozen serum phase (sugars, proteins, and stabilizers). This microstructure is responsible for ice cream's melting characteristics. By varying both formulation (emulsifier content and overrun) and processing conditions (dasher speed), the effects of different microstructural elements, particularly air cells and fat globule clusters, on ice cream melt-down properties were studied. Factors that caused an increase in shear stress within the freezer, namely increasing dasher speed and overrun, caused a decrease in air cell size and an increase in extent of fat destabilization. Increasing emulsifier content, especially of polysorbate 80, caused an increase in extent of fat destabilization. Both overrun and fat destabilization influenced drip-through rates. Ice creams with a combination of low overrun and low fat destabilization had the highest drip-through rates. Further, the amount of remnant foam left on the screen increased with reduced drip-through rates. These results provide a better understanding of the effects of microstructure components and their interactions on drip-through rate. Manipulating operating and formulation parameters in ice cream manufacture influences the microstructure (air cells, ice crystals, and fat globule clusters). This work provides guidance on which parameters have most effect on air cell size and fat globule cluster formation. Further, the structural characteristics that reduce melt-down rate were determined. Ice cream manufacturers will use these results to tailor their products for the desired quality attributes. © 2018 Institute of Food Technologists®.

A novel mechanism for emulating insect wing kinematics

International Nuclear Information System (INIS)

Seshadri, Pranay; Benedict, Moble; Chopra, Inderjit

2012-01-01

A novel dual-differential four-bar flapping mechanism that can accurately emulate insect wing kinematics in all three degrees of freedom (translation, rotation and stroke plane deviation) is developed. The mechanism is specifically designed to be simple and scalable such that it can be utilized on an insect-based flapping wing micro air vehicle. Kinematic formulations for the wing stroke position, pitch angle and coning angle for this model are derived from first principles and compared with a 3D simulation. A benchtop flapping mechanism based on this model was designed and built, which was also equipped with a balance for force measurements. 3D motion capture tests were conducted on this setup to demonstrate the capability of generating complex figure-of-eight flapping motions along with dynamic pitching. The dual-differential four-bar mechanism was implemented on a light-weight vehicle that demonstrated tethered hover. (paper)

Comparative Emulsifying Properties of Octenyl Succinic Anhydride (OSA-Modified Starch: Granular Form vs Dissolved State.

Directory of Open Access Journals (Sweden)

María Matos

Full Text Available The emulsifying ability of OSA-modified and native starch in the granular form, in the dissolved state and a combination of both was compared. This study aims to understand mixed systems of particles and dissolved starch with respect to what species dominates at droplet interfaces and how stability is affected by addition of one of the species to already formed emulsions. It was possible to create emulsions with OSA-modified starch isolated from Quinoa as sole emulsifier. Similar droplet sizes were obtained with emulsions prepared at 7% (w/w oil content using OSA-modified starch in the granular form or molecularly dissolved but large differences were observed regarding stability. Pickering emulsions kept their droplet size constant after one month while emulsions formulated with OSA-modified starch dissolved exhibited coalescence. All emulsions stabilized combining OSA-modified starch in granular form and in solution showed larger mean droplet sizes with no significant differences with respect to the order of addition. These emulsions were unstable due to coalescence regarding presence of free oil. Similar results were obtained when emulsions were prepared by combining OSA-modified granules with native starch in solution. The degree of surface coverage of starch granules was much lower in presence of starch in solution which indicates that OSA-starch is more surface active in the dissolved state than in granular form, although it led to unstable systems compared to starch granule stabilized Pickering emulsions, which demonstrated to be extremely stable.

Multi-level emulation of a volcanic ash transport and dispersion model to quantify sensitivity to uncertain parameters

Directory of Open Access Journals (Sweden)

N. J. Harvey

2018-01-01

Full Text Available Following the disruption to European airspace caused by the eruption of Eyjafjallajökull in 2010 there has been a move towards producing quantitative predictions of volcanic ash concentration using volcanic ash transport and dispersion simulators. However, there is no formal framework for determining the uncertainties of these predictions and performing many simulations using these complex models is computationally expensive. In this paper a Bayesian linear emulation approach is applied to the Numerical Atmospheric-dispersion Modelling Environment (NAME to better understand the influence of source and internal model parameters on the simulator output. Emulation is a statistical method for predicting the output of a computer simulator at new parameter choices without actually running the simulator. A multi-level emulation approach is applied using two configurations of NAME with different numbers of model particles. Information from many evaluations of the computationally faster configuration is combined with results from relatively few evaluations of the slower, more accurate, configuration. This approach is effective when it is not possible to run the accurate simulator many times and when there is also little prior knowledge about the influence of parameters. The approach is applied to the mean ash column loading in 75 geographical regions on 14 May 2010. Through this analysis it has been found that the parameters that contribute the most to the output uncertainty are initial plume rise height, mass eruption rate, free tropospheric turbulence levels and precipitation threshold for wet deposition. This information can be used to inform future model development and observational campaigns and routine monitoring. The analysis presented here suggests the need for further observational and theoretical research into parameterisation of atmospheric turbulence. Furthermore it can also be used to inform the most important parameter perturbations

Effect of tartarate and citrate based food additives on the micellar properties of sodium dodecylsulfate for prospective use as food emulsifier.

Science.gov (United States)

Banipal, Tarlok S; Kaur, Harjinder; Kaur, Amanpreet; Banipal, Parampaul K

2016-01-01

Citrate and tartarate based food preservatives can be used to enhance the emulsifying properties of sodium dodecylsulfate (SDS) based micellar system and thus making it appropriate for food applications. Exploration of interactions between the two species is the key constraint for execution of such ideas. In this work various micellar and thermodynamic parameters of SDS like critical micellar concentration (CMC), standard Gibbs free energy of micellization (ΔG(0)mic.) etc. have been calculated in different concentrations of disodium tartarate (DST) and trisodium citrate (TSC) in the temperature range (288.15-318.15)K from the conductivity and surface tension measurements. The parameters obtained from these studies reveal the competitive nature of both the additives with SDS for available positions at the air/water interface. TSC is found to be more effective additive in order to make SDS micellar system better for its potential applications as food emulsifier. Copyright © 2015 Elsevier Ltd. All rights reserved.

Assessing the Usability of Gaze-Adapted Interface against Conventional Eye-based Input Emulation

OpenAIRE

Kumar, Chandan; Menges, Raphael; Staab, Steffen

2017-01-01

In recent years, eye tracking systems have greatly improved, beginning to play a promising role as an input medium. Eye trackers can be used for application control either by simply emulating the mouse and keyboard devices in the traditional graphical user interface, or by customized interfaces for eye gaze events. In this work, we evaluate these two approaches to assess their impact in usability. We present a gaze-adapted Twitter application interface with direct interaction of eye gaze inpu...

Method using in vivo quantitative spectroscopy to guide design and optimization of low-cost, compact clinical imaging devices: emulation and evaluation of multispectral imaging systems

Science.gov (United States)

Saager, Rolf B.; Baldado, Melissa L.; Rowland, Rebecca A.; Kelly, Kristen M.; Durkin, Anthony J.

2018-04-01

With recent proliferation in compact and/or low-cost clinical multispectral imaging approaches and commercially available components, questions remain whether they adequately capture the requisite spectral content of their applications. We present a method to emulate the spectral range and resolution of a variety of multispectral imagers, based on in-vivo data acquired from spatial frequency domain spectroscopy (SFDS). This approach simulates spectral responses over 400 to 1100 nm. Comparing emulated data with full SFDS spectra of in-vivo tissue affords the opportunity to evaluate whether the sparse spectral content of these imagers can (1) account for all sources of optical contrast present (completeness) and (2) robustly separate and quantify sources of optical contrast (crosstalk). We validate the approach over a range of tissue-simulating phantoms, comparing the SFDS-based emulated spectra against measurements from an independently characterized multispectral imager. Emulated results match the imager across all phantoms (<3 % absorption, <1 % reduced scattering). In-vivo test cases (burn wounds and photoaging) illustrate how SFDS can be used to evaluate different multispectral imagers. This approach provides an in-vivo measurement method to evaluate the performance of multispectral imagers specific to their targeted clinical applications and can assist in the design and optimization of new spectral imaging devices.

rpe v5: an emulator for reduced floating-point precision in large numerical simulations

Science.gov (United States)

Dawson, Andrew; Düben, Peter D.

2017-06-01

This paper describes the rpe (reduced-precision emulator) library which has the capability to emulate the use of arbitrary reduced floating-point precision within large numerical models written in Fortran. The rpe software allows model developers to test how reduced floating-point precision affects the result of their simulations without having to make extensive code changes or port the model onto specialized hardware. The software can be used to identify parts of a program that are problematic for numerical precision and to guide changes to the program to allow a stronger reduction in precision.The development of rpe was motivated by the strong demand for more computing power. If numerical precision can be reduced for an application under consideration while still achieving results of acceptable quality, computational cost can be reduced, since a reduction in numerical precision may allow an increase in performance or a reduction in power consumption. For simulations with weather and climate models, savings due to a reduction in precision could be reinvested to allow model simulations at higher spatial resolution or complexity, or to increase the number of ensemble members to improve predictions. rpe was developed with a particular focus on the community of weather and climate modelling, but the software could be used with numerical simulations from other domains.

Bacterial degradation of emulsified crude oil and the effects of various surfactants

International Nuclear Information System (INIS)

Bruheim, P.; Bredholt, H.; Eimhjellen, K.

1997-01-01

The effects of surfactants on the oxidation rate of alkanes in crude oil were investigated using a selected bacterial species, Rhodococcus sp., pregrown to various growth stages. Oxidation rates were measured in a three-hour period by Warburg respirometry. Response to emulsified oil was found to be dependent on the physiological state of the bacteria. In the exponential growth phase oxidation rates were negatively affected by surfactant amendment, whereas in the stationary growth phase oxidation rates appear to have been stimulated. The stimulatory effect was attributed to the chemical structure and physico-chemical properties of the surfactants. Surfactants with hydrophilic-lipophilic balance values (HLB) in the intermediate range of 8-12 gave the best values. Neither the commercial dispersants nor the biosurfactants exhibited any stimulative effects. 21 refs., 4 tabs., 1 fig

Emulation of MS DOS Operational System on the Autonomous Crate-Controller with I8086 microprocessor

International Nuclear Information System (INIS)

Hons, Z.; Cizek, P.; Streit, V.

1988-01-01

KM-DOS operating system for CAMAC autonomous crate-controller based on Intel 8086/8087 microprocessor connected with Pravec-16 IBM PC is described. The KM-DOS system fully emulates the MS DOS environment on the CAMAC controller. Thus ASSEMBLER, FORTRAN, C and PASCAL programs compiled and linked on IBM PC and compatible can be run on the CAMAC controller and parall work of both computers is enabled

Nanoemulsions produced with varied type of emulsifier and oil content: An influence of formulation and process parameters on the characteristics and physical stability

Directory of Open Access Journals (Sweden)

Đorđević Sanela M.

2013-01-01

Full Text Available The aim of the present study was to prepare oil-in-water nanoemulsions stabilized with a novel natural alkyl polyglucoside surfactant and to compare them with corresponding lecithin/polysorbate 80 - based nanoemulsions in terms of physicochemical properties and physical stability. Nanoemulsions were prepared by high pressure homogenization, using 20, 30 and 40% (w/w medium chain triglyceride as oil phase, and 4, 6 and 8% (w/w lecithin/polysorbate 80 mixture (1/1 or caprylyl/capryl glucoside as emulsifiers. The influence of emulsifier type, emulsifier concentration and oil content was investigated with respect to changes in particle size, particle size distribution, surface charge and physical stability. The influence of production parameters (number of homogenization cycles, type of homogenization process, homogenization pressure on particle size was also investigated. Analysis was performed by photon correlation spectroscopy, laser diffraction, zeta potential, pH and electrical conductivity measurements. All formulations produced revealed a small droplet size ranging from 147 to 228 nm and a very narrow size distribution (polydispersity index range 0,072-0,124. Zeta potentials were about -20 mV and -50 mV for nanoemulsions stabilized with lecithin/polysorbate 80 and caprylyl/capryl glucoside, respectively. The results obtained during the stability studies (6 months at 25°C and 1 month at 40°C indicated that nanoemulsion stability was influenced by their composition. Acquired results also suggested the most appropriate production parameters: 9 homogenization cycles, homogenization pressure of 500 bar and discontinuous process of homogenization.

Emulsifier type, metal chelation and pH affect oxidative stability of n-3-enriched emulsions

DEFF Research Database (Denmark)

Haahr, Anne-Mette; Jacobsen, Charlotte

2008-01-01

-enriched oil-in-water emulsion. The selected food emulsifiers were Tween 80, Citrem, sodium caseinate and lecithin. Lipid oxidation was evaluated by determination of peroxide values and secondary volatile oxidation products. Moreover, the zeta potential and the droplet sizes were determined. Twen resulted...... in the least oxidatively stable emulsions, followed by Citrem. When iron was present, caseinate-stabilized emulsions oxidized slower than lecithin emulsions at pH 3, whereas the opposite was the case at pH 7. Oxidation generally progressed faster at pH 3 than at pH 7, irrespective of the addition of iron. EDTA...

GW170817 falsifies dark matter emulators

Science.gov (United States)

Boran, S.; Desai, S.; Kahya, E. O.; Woodard, R. P.

2018-02-01

On August 17, 2017 the LIGO interferometers detected the gravitational wave (GW) signal (GW170817) from the coalescence of binary neutron stars. This signal was also simultaneously seen throughout the electromagnetic (EM) spectrum from radio waves to gamma rays. We point out that this simultaneous detection of GW and EM signals rules out a class of modified gravity theories, termed "dark matter emulators," which dispense with the need for dark matter by making ordinary matter couple to a different metric from that of GW. We discuss other kinds of modified gravity theories which dispense with the need for dark matter and are still viable. This simultaneous observation also provides the first observational test of Einstein's weak equivalence principle (WEP) between gravitons and photons. We estimate the Shapiro time delay due to the gravitational potential of the total dark matter distribution along the line of sight (complementary to the calculation by Abbott et al. [Astrophys. J. Lett. 848, L13 (2017)], 10.3847/2041-8213/aa920c) to be about 400 days. Using this estimate for the Shapiro delay and from the time difference of 1.7 seconds between the GW signal and gamma rays, we can constrain violations of the WEP using the parametrized post-Newtonian parameter γ , and it is given by |γGW-γEM|<9.8 ×10-8.

Preparation of magnetic latexes functionalized with chloromethyl groups via emulsifier-free miniemulsion polymerization

International Nuclear Information System (INIS)

Faridi-Majidi, Reza; Sharifi-Sanjani, Naser

2007-01-01

Functionalized crosslinked polystyrene-co-divinylbenzene-co-chloromethylstyrene magnetic latex particles were prepared via emulsifier-free miniemulsion polymerization using 2, 2' azobis (2-amidinopropane) dihydrochloride (V-50) as an initiator and in the presence of magnetite nanoparticles in the monomers. Transmission electron microscopy (TEM) proved the presence of magnetite nanoparticles in polymer particles. Differential scanning calorimetery (DSC) analysis of the product showed an exothermic signal due to crosslinking of chains through electrophilic aromatic substitution of phenyl groups with chloromethyl groups in the presence of the dispersed Fe 3 O 4 as Lewis acid. This was proven by thermogravimetric analysis (TGA) via the loss of gaseous HCl. The results were also compared with those of magnetite-free miniemulsion polymerization using V-50

Preparation of magnetic latexes functionalized with chloromethyl groups via emulsifier-free miniemulsion polymerization

Energy Technology Data Exchange (ETDEWEB)

Faridi-Majidi, Reza [School of Chemistry, University College of Science, Tehran University, Tehran (Iran, Islamic Republic of)]. E-mail: refaridi@khayam.ut.ac.ir; Sharifi-Sanjani, Naser [School of Chemistry, University College of Science, Tehran University, Tehran (Iran, Islamic Republic of)

2007-04-15

Functionalized crosslinked polystyrene-co-divinylbenzene-co-chloromethylstyrene magnetic latex particles were prepared via emulsifier-free miniemulsion polymerization using 2, 2' azobis (2-amidinopropane) dihydrochloride (V-50) as an initiator and in the presence of magnetite nanoparticles in the monomers. Transmission electron microscopy (TEM) proved the presence of magnetite nanoparticles in polymer particles. Differential scanning calorimetery (DSC) analysis of the product showed an exothermic signal due to crosslinking of chains through electrophilic aromatic substitution of phenyl groups with chloromethyl groups in the presence of the dispersed Fe{sub 3}O{sub 4} as Lewis acid. This was proven by thermogravimetric analysis (TGA) via the loss of gaseous HCl. The results were also compared with those of magnetite-free miniemulsion polymerization using V-50.

Quality characteristics of Dutch-style fermented sausages manufactured with partial replacement of pork back-fat with pure, pre-emulsified or encapsulated fish oil

NARCIS (Netherlands)

Josquin, N.M.; Linssen, J.P.H.; Houben, J.H.

2012-01-01

Dutch-style fermented sausages were manufactured with 15% and 30% pork back-fat substitution by pure or commercial encapsulated fish oil, either added as such or as pre-emulsified mixture with soy protein isolate. Adding commercial encapsulated fish oil was the most important factor influencing the

Emulating Spherical Wave Channel Models in Multi-probe Anechoic Chamber Setups

DEFF Research Database (Denmark)

Fan, Wei; Carreño, Xavier; Nielsen, Jesper Ødum

2015-01-01

to emulate spherical wave channel models in multi-probe anechoic chamber setups. In this paper, a technique based on the field synthesis principle is proposed to approximate spherical waves emitted from arbitrarily located point sources with arbitrary polarizations. Simulation results show that static......Spherical wave channel modeling has attracted huge research attention for massive multiple-input multiple-output (MIMO) and short-distance MIMO systems. Current research work in multi-probe anechoic chamber systems is limited to reproduce radio channels assuming planar wavefronts. There is a need...... spherical waves can be reproduced with a limited number of probes, and the field synthesis accuracy of spherical wave depends on the location of the source point....

Self-emulsifying drug delivery systems: Design of a novel vaginal delivery system for curcumin.

Science.gov (United States)

Köllner, S; Nardin, I; Markt, R; Griesser, J; Prüfert, F; Bernkop-Schnürch, A

2017-06-01

The aim of this study was to develop a vaginal self-emulsifying delivery system for curcumin being capable of spreading, of permeating the mucus gel layer and of protecting the drug being incorporated in oily nanodroplets towards mucus interactions and immobilization. The emulsifying properties of curcumin loaded SEDDS containing 30% Cremophor RH40, 20% Capmul PG-8, 30% Captex 300, 10% DMSO and 10% tetraglycol (SEDD formulation A) as well as 25% PEG 200, 35% Cremophor RH40, 20% Captex 355, 10% Caprylic acid and 10% Tween 80 (SEDD formulation B) after diluting 1+2 with artificial vaginal fluid were characterized regarding droplet size and zeta potential. Collagen swelling test was used to examine the irritation potential of SEDDS. Additionally to mucus binding studies, permeation studies in the mucus were performed. Furthermore, spreading potential of the novel developed formulations was compared with a commercial available o/w cream (non-ionic hydrophilic cream) on vaginal mucosa. SEDDS displayed a mean droplet size between 38 and 141nm and a zeta potential of -0.3 to -1.6mV. The collagen swelling test indicated no significant irritation potential of both formulations over 24h. An immediate interaction of unformulated curcumin with the mucus was determined, whereas both SEDDS facilitated drug permeation through the mucus layer. Formulation B showed a 2.2-fold improved transport ratio of curcumin compared to SEDD formulation A. In comparison to the vaginal cream, SEDD formulation A and B were able to spread over the vaginal mucosa and cover the tissue to a 17.8- and 14.8-fold higher extent, respectively. According to these results, SEDDS seems to be a promising tool for vaginal application. Copyright © 2017 Elsevier B.V. All rights reserved.

Bioaccessibility and Cellular Uptake of β-Carotene Encapsulated in Model O/W Emulsions: Influence of Initial Droplet Size and Emulsifiers

Directory of Open Access Journals (Sweden)

Wei Lu

2017-09-01

Full Text Available The effects of the initial emulsion structure (droplet size and emulsifier on the properties of β-carotene-loaded emulsions and the bioavailability of β-carotene after passing through simulated gastrointestinal tract (GIT digestion were investigated. Exposure to GIT significantly changed the droplet size, surface charge and composition of all emulsions, and these changes were dependent on their initial droplet size and the emulsifiers used. Whey protein isolate (WPI-stabilized emulsion showed the highest β-carotene bioaccessibility, while sodium caseinate (SCN-stabilized emulsion showed the highest cellular uptake of β-carotene. The bioavailability of emulsion-encapsulated β-carotene based on the results of bioaccessibility and cellular uptake showed the same order with the results of cellular uptake being SCN > TW80 > WPI. An inconsistency between the results of bioaccessibility and bioavailability was observed, indicating that the cellular uptake assay is necessary for a reliable evaluation of the bioavailability of emulsion-encapsulated compounds. The findings in this study contribute to a better understanding of the correlation between emulsion structure and the digestive fate of emulsion-encapsulated nutrients, which make it possible to achieve controlled or potential targeted delivery of nutrients by designing the structure of emulsion-based carriers.

The effect of emulsifying salts on the turbidity of a diluted milk system with varying pH and protein concentration.

Science.gov (United States)

Culler, M D; Saricay, Y; Harte, F M

2017-06-01

Solutions of 10 commonly used emulsifying salts (ES) listed in the Code of Federal Regulations (21CFR133.179) for pasteurized process cheese were tested for their effect on the turbidity of a diluted milk system at different pH and protein concentrations to characterize the conditions that affect micellar structure. Emulsifying salt solutions were made by mixing the ES in a 1-in-20 dilution of water in skim milk ultrafiltrate (3 kDa molecular weight cut-off) to obtain ES concentrations from 0 to 248 mM. Skim milk was added to solutions containing nanopure water, skim milk ultrafiltrate, and a specific ES ranging in concentration from 0 to 248 mM and pH 5, 5.8, 6.8, 7.8, and 8.8. The turbidity of the samples was measured as the optical density at 400 nm immediately after mixing (time, t = 0), after 30 s (t = 30s), and after 30 min (t = 30min). Emulsifying salts were found to cause a decrease in the turbidity of the system, which was modeled using an exponential decay model, where C* represents a threshold salt concentration at which rapid dissociation occurs. At pH values 5.8 and 6.8, the ES caused the greatest decrease in turbidity of the diluted milk system. At pH 5, the ES had the least effect on the turbidity of the system. Sodium hexametaphosphate was found to have the strongest dissociative effect, with a C* value of 0.33 mM for t = 0 at pH 6.8. In contrast, the largest C* value calculated at pH 6.8 was monosodium phosphate at 278.22 mM. Increased time resulted in lower C* values. The model established for this study can be used to predict the dissociation of casein micelles in the presence of various types of ES. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

The effect of clove bud powder at a spice level on antioxidant and quality properties of emulsified pork sausage during cold storage.

Science.gov (United States)

Jin, Sang-Keun; Choi, Jung-Seok; Jeong, Jin-Yeon; Kim, Gap-Don

2016-09-01

Clove bud is a widely used spice in meat and meat products, and it contains high level of phenolic compounds. The effectiveness of the clove as a spice has not been fully studied at a general level of addition in the meat products. Therefore, in the present study, the antioxidant, antimicrobial, and nitrite scavenging abilities of clove bud powder (CBP) was assessed at spice level (0.1% and 0.2%) in emulsified pork sausage, during 6 weeks of cold storage. CBP had DPPH radical scavenging ability, but CBP addition at 0.1% and 0.2% did not decrease the TBARS value. An antimicrobial effect of CBP was also not observed during the cold storage. However, residual nitrite at storage weeks 4 and 6 was shown to be lower (P 0.05). The positive effect on nitrite scavenging could be expected by the addition of 0.2% CBP as a spice. However, antioxidant and antimicrobial abilities were not observed, as well as improvement in the quality of characteristics, in emulsified pork sausage. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Aerodynamic consequences of wing morphing during emulated take-off and gliding in birds.

Science.gov (United States)

Klaassen van Oorschot, Brett; Mistick, Emily A; Tobalske, Bret W

2016-10-01

Birds morph their wings during a single wingbeat, across flight speeds and among flight modes. Such morphing may allow them to maximize aerodynamic performance, but this assumption remains largely untested. We tested the aerodynamic performance of swept and extended wing postures of 13 raptor species in three families (Accipitridae, Falconidae and Strigidae) using a propeller model to emulate mid-downstroke of flapping during take-off and a wind tunnel to emulate gliding. Based on previous research, we hypothesized that (1) during flapping, wing posture would not affect maximum ratios of vertical and horizontal force coefficients (C V :C H ), and that (2) extended wings would have higher maximum C V :C H when gliding. Contrary to each hypothesis, during flapping, extended wings had, on average, 31% higher maximum C V :C H ratios and 23% higher C V than swept wings across all biologically relevant attack angles (α), and, during gliding, maximum C V :C H ratios were similar for the two postures. Swept wings had 11% higher C V than extended wings in gliding flight, suggesting flow conditions around these flexed raptor wings may be different from those in previous studies of swifts (Apodidae). Phylogenetic affiliation was a poor predictor of wing performance, due in part to high intrafamilial variation. Mass was only significantly correlated with extended wing performance during gliding. We conclude that wing shape has a greater effect on force per unit wing area during flapping at low advance ratio, such as take-off, than during gliding. © 2016. Published by The Company of Biologists Ltd.

Effect of emulsion size and shelf life of azadirachtin A on the bioefficacy of neem (Azadirachta indica A. Juss) emulsifiable concentrates.

Science.gov (United States)

Kumar, L; Parmar, B S

2000-08-01

In a study of 33 recipes of neem oil based emulsifiable concentrates, the specific surface area of the emulsions and cream plus oil layer separation in emulsions at 24 h revealed a correlation of -0.6874 between them and correlations of -0.8940 and 0.6972, respectively, with bioefficacy (LC(50)) against the 3-day-old second-instar larvae of the Bihar hairy caterpillar, Spilosoma obliqua Walker. Nearly 96-99% of azadirachtin A in emulsifiable concentrates (aza-A content = 617.93-1149.65 ppm) degraded during the heat stability test at 54 +/- 1 degrees C for 14 days with half-lives ranging between 1.84 and 4.53 days. The LC(50) values against S. obliqua were, however, statistically at par in both the pre- and the post-heat-treated samples, suggesting a similar effect of azadirachtin A and its degradation products on the bioactivity. The half-life of azadirachtin A could be enhanced by storing the concentrates at lower temperatures. A low pH of the formulation solvent did not check the degradation of azadirachtin A, as reported with aqueous solutions in the literature.

A Real Time Electronics Emulator with Realistic Data Generation for Reception Tests of the CMS ECAL Front-End Boards

CERN Document Server

Romanteau, T; Collard, Caroline; Debraine, A; Decotigny, D; Dobrzynski, L; Karar, A; Regnault, N

2005-01-01

The CMS [1] electromagnetic calorimeter (ECAL) [2] uses 3 132 Front-End boards (FE) performing both trigger and data readout functions. Prior to their integration at CERN, the FE boards have to be validated by dedicated test bench systems. The final one, called "XFEST" (eXtended Front-End System Test) and for which the present developments have been performed, is located at Laboratoire Leprince-Ringuet. In this contribution, a solution is described to efficiently test a large set of complex electronics boards characterized by a large number of input ports and a high throughput data rate. To perform it, an algorithm to simulate the Very Front End signals has been emulated. The project firmwares use VHDL embedded into XILINX Field Programmable Gate Array circuits (FPGA). This contribution describes the solutions developed in order to create a realistic digital input patterns real-time emul ator working at 40 MHz. The implementation of a real time comparison of the FE output streams as well as the test bench wil...

DEMONSTRATION OF IN SITU DEHALOGENATION OF DNAPL THROUGH INJECTION OF EMULSIFIED ZERO-VALIENT IRON AT LAUNCH COMPLEX 34 IN CAPE CANAVERAL AIR FORCE STATION, FLORIDA

Science.gov (United States)

The purpose of this project was to evaluate the technical and cost performance of emulsified zero-valent iron (EZVI) technology when applied to DNAPL contaminants in the saturated zone. This demonstration was conducted at Launch Complex 34, Cape Canaveral Air Force Station, FL, w...

An intravenously injectable emulsified iodinated oil contrast agent for liver CT. Experimental study of lipiodol emulsion emulsified by lecithin (LEL38) in rabbits

International Nuclear Information System (INIS)

Kamei, Tsuyoshi

1994-01-01

LEL38 (lipiodol emulsion emulsified by lecithin 38 mgI/ml, mean diameter 200 nm) is a new intravenously injectable oil contrast agent for liver CT. The aim of this report was to evaluate its ability to enhance contrast in the liver of 46 rabbits with regard to the correlation of density with time at an injected dose of 76 mgI/kg (before to 120 minutes after), the correlation of density with dose (0-760 mgI/kg) and the detectability of liver mass. The time-density correlation of LEL38 in the liver, that is, peak density, was achieved after 30 minutes, and it was elevated to 20.9 H. U. Thereafter, it decreased slowly. In the blood vessels, it reached a sharp peak after immediately being elevated to 14. 7 H. U. Thereafter detectability decreased quickly. The maximum difference in density between liver and blood vessels was 34 H. U. after 60 minutes. The dose-density correlation in the liver and blood vessels was linear. Tumors were detected as clear areas of low density. The minimal detectability was about 3 mm. LEL38 may be an effective contrast agent for screening CT studies of liver disease. (author)

Calibration of uncertain inputs to computer models using experimentally measured quantities and the BMARS emulator

International Nuclear Information System (INIS)

Stripling, H.F.; McClarren, R.G.; Kuranz, C.C.; Grosskopf, M.J.; Rutter, E.; Torralva, B.R.

2011-01-01

We present a method for calibrating the uncertain inputs to a computer model using available experimental data. The goal of the procedure is to produce posterior distributions of the uncertain inputs such that when samples from the posteriors are used as inputs to future model runs, the model is more likely to replicate (or predict) the experimental response. The calibration is performed by sampling the space of the uncertain inputs, using the computer model (or, more likely, an emulator for the computer model) to assign weights to the samples, and applying the weights to produce the posterior distributions and generate predictions of new experiments within confidence bounds. The method is similar to the Markov chain Monte Carlo (MCMC) calibration methods with independent sampling with the exception that we generate samples beforehand and replace the candidate acceptance routine with a weighting scheme. We apply our method to the calibration of a Hyades 2D model of laser energy deposition in beryllium. We employ a Bayesian Multivariate Adaptive Regression Splines (BMARS) emulator as a surrogate for Hyades 2D. We treat a range of uncertainties in our system, including uncertainties in the experimental inputs, experimental measurement error, and systematic experimental timing errors. The results of the calibration are posterior distributions that both agree with intuition and improve the accuracy and decrease the uncertainty in experimental predictions. (author)

Reforging the Wedding Ring: Exploring a Semi-Artificial Model of Population for the United Kingdom with Gaussian process emulators

Directory of Open Access Journals (Sweden)

Viet Dung Cao

2013-10-01

Full Text Available Background: We extend the "Wedding Ring‟ agent-based model of marriage formation to include some empirical information on the natural population change for the United Kingdom together with behavioural explanations that drive the observed nuptiality trends. Objective: We propose a method to explore statistical properties of agent-based demographic models. By coupling rule-based explanations driving the agent-based model with observed data we wish to bring agent-based modelling and demographic analysis closer together. Methods: We present a Semi-Artificial Model of Population, which aims to bridge demographic micro-simulation and agent-based traditions. We then utilise a Gaussian process emulator - a statistical model of the base model - to analyse the impact of selected model parameters on two key model outputs: population size and share of married agents. A sensitivity analysis is attempted, aiming to assess the relative importance of different inputs. Results: The resulting multi-state model of population dynamics has enhanced predictive capacity as compared to the original specification of the Wedding Ring, but there are some trade-offs between the outputs considered. The sensitivity analysis allows identification of the most important parameters in the modelled marriage formation process. Conclusions: The proposed methods allow for generating coherent, multi-level agent-based scenarios aligned with some aspects of empirical demographic reality. Emulators permit a statistical analysis of their properties and help select plausible parameter values. Comments: Given non-linearities in agent-based models such as the Wedding Ring, and the presence of feedback loops, the uncertainty in the model may not be directly computable by using traditional statistical methods. The use of statistical emulators offers a way forward.

A Robotic Fish to Emulate the Fast-Start

Science.gov (United States)

Currier, Todd; Ma, Ganzhong; Modarres-Sadeghi, Yahya

2017-11-01

An experimental study is conducted on a robotic fish designed to emulate the fast-start response. The fish body is constructed of 3D printed ribs and a light spring steel spine. The body is actuated using a series of pressured pistons. A total of four pistons are supplied with pressure through lightweight high pressure service lines. The source of pressure is carbon dioxide with a 700 psi peak operating pressure resulting in a body response that can cycle a c-start maneuver in milliseconds. The motion of the fish is precisely controlled through the use of solenoids with a control signal produced by a programmable microprocessor. The fish is constrained in all translational degrees of freedom but allowed to rotate about a vertical axis. The influence of the point of rotation is studied with different mounting points along the length of the head of the fish. The forces are measured in two perpendicular in-plane directions. A high speed camera is used to capture the response of the fish and the corresponding flow around it. Comparison is made with the kinematics observed in live fish.

Mining data from hemodynamic simulations via Bayesian emulation

Directory of Open Access Journals (Sweden)

Nair Prasanth B

2007-12-01

Full Text Available Abstract Background: Arterial geometry variability is inevitable both within and across individuals. To ensure realistic prediction of cardiovascular flows, there is a need for efficient numerical methods that can systematically account for geometric uncertainty. Methods and results: A statistical framework based on Bayesian Gaussian process modeling was proposed for mining data generated from computer simulations. The proposed approach was applied to analyze the influence of geometric parameters on hemodynamics in the human carotid artery bifurcation. A parametric model in conjunction with a design of computer experiments strategy was used for generating a set of observational data that contains the maximum wall shear stress values for a range of probable arterial geometries. The dataset was mined via a Bayesian Gaussian process emulator to estimate: (a the influence of key parameters on the output via sensitivity analysis, (b uncertainty in output as a function of uncertainty in input, and (c which settings of the input parameters result in maximum and minimum values of the output. Finally, potential diagnostic indicators were proposed that can be used to aid the assessment of stroke risk for a given patient's geometry.

Contribution to the study of the physical stability of the suspensions of zinc oxide, titanium dioxide and precipitated sulphur employing emulsified solid greases like vehicle

International Nuclear Information System (INIS)

Porras Navarro, Martha

2001-01-01

This research evaluated the physical stability of the suspensions of zinc oxide, precipitated sulphur and titanium dioxide. By using emulsified vehicles of three solid greases: stearilic alcohol, stearic acid and beeswax. That varies the concentration of solid grease (2%, 4%, 6 %) and the velocity of agitation for the emulsified vehicle's preparation (250, 500, 750 revolutions by minutes). That got 81 suspensions, 27 for every grease employed. The following effects there were evaluated like indicators of the physical stability of the suspensions: volume of sediment, apparent viscosity, facility of resuspension. There was effected an analysis of the varying of two controlled factors to establish the importance since the statistical viewpoint of the variants of the process over the volume of the sediment. This study indicates that the selection of solid grease is an parameter which influence is significant, what supports the got data through the research. By giving as a result that the stearilic alcohol is the most competent vehicle for the preparation of these suspensions. (Author) [es

Emulating facial biomechanics using multivariate partial least squares surrogate models.

Science.gov (United States)

Wu, Tim; Martens, Harald; Hunter, Peter; Mithraratne, Kumar

2014-11-01

A detailed biomechanical model of the human face driven by a network of muscles is a useful tool in relating the muscle activities to facial deformations. However, lengthy computational times often hinder its applications in practical settings. The objective of this study is to replace precise but computationally demanding biomechanical model by a much faster multivariate meta-model (surrogate model), such that a significant speedup (to real-time interactive speed) can be achieved. Using a multilevel fractional factorial design, the parameter space of the biomechanical system was probed from a set of sample points chosen to satisfy maximal rank optimality and volume filling. The input-output relationship at these sampled points was then statistically emulated using linear and nonlinear, cross-validated, partial least squares regression models. It was demonstrated that these surrogate models can mimic facial biomechanics efficiently and reliably in real-time. Copyright © 2014 John Wiley & Sons, Ltd.

Reduced time delay for gravitational waves with dark matter emulators

International Nuclear Information System (INIS)

Desai, S.; Kahya, E. O.; Woodard, R. P.

2008-01-01

We discuss the implications for gravitational wave detectors of a class of modified gravity theories which dispense with the need for dark matter. These models, which are known as dark matter emulators, have the property that weak gravitational waves couple to the metric that would follow from general relativity without dark matter whereas ordinary particles couple to a combination of the metric and other fields which reproduces the result of general relativity with dark matter. We show that there is an appreciable difference in the Shapiro delays of gravitational waves and photons or neutrinos from the same source, with the gravitational waves always arriving first. We compute the expected time lags for GRB 070201, for SN 1987a and for Sco-X1. We estimate the probable error by taking account of the uncertainty in position, and by using three different dark matter profiles

Avaliação da estabilidade e atividade antioxidante de uma emulsão base não-iônica contendo resveratrol

Directory of Open Access Journals (Sweden)

Marcela Kist Lange

2009-03-01

Full Text Available Vários são os fatores que podem ocasionar a instabilidade de uma emulsão, destacando-se a oxidação, reação prevenida pelo emprego de antioxidantes. O butil-hidróxi-tolueno (BHT tem sido um dos antioxidantes sintéticos mais utilizados em formulações cosméticas, porém, a busca da indústria farmacêutica e cosmética pelo emprego de produtos de origem natural tem sido cada vez maior. Visto isso, o objetivo do presente trabalho foi a incorporação do resveratrol, um composto fenólico encontrado principalmente em uvas bem como em vinhos tintos, em uma emulsão base não-iônica para avaliação do perfil de estabilidade e atividade antioxidante em comparação a uma emulsão base não-iônica contendo o BHT. O perfil de estabilidade foi analisado pela observação das características organolépticas, determinação do pH e espalhabilidade, e atividade antioxidante através do teste com o radical livre 2,2-difenil-1-picrilhidrazila (DPPH. Em relação à estabilidade, a altas temperaturas, a emulsão contendo BHT mostrou-se superior à emulsão contendo resveratrol. Pela análise da atividade antioxidante, o resveratrol tanto na sua forma de extrato seco, como quando incorporado na emulsão, demonstrou significativa superioridade em relação ao BHT, podendo ser sua utilização uma alternativa viável em preparações cosméticas, devido ao seu grande potencial antioxidante.There are several factors that can lead to the instability of an emulsion, highlighting the oxidation, a reaction prevented by the use of antioxidants. The butylated hydroxytoluene (BHT has been one of the most used synthetic antioxidants in cosmetic formulations; however, pharmaceutical and cosmetic industries have shown considerable interest regarding the search for the use of natural products. Based on this, the objective of this work was the incorporation of resveratrol, a natural phenolic compound found mainly in grapes as well as in red wines, into a non

Nanoemulsions of thymol and eugenol co-emulsified by lauric arginate and lecithin.

Science.gov (United States)

Ma, Qiumin; Davidson, P Michael; Zhong, Qixin

2016-09-01

Lauric arginate (LAE) is a cationic surfactant with excellent antimicrobial activities. To incorporate essential oil components (EOCs) in aqueous systems, properties of EOC nanoemulsions prepared with a LAE and lecithin mixture were studied. The LAE-lecithin mixture resulted in stable translucent nanoemulsions of thymol and eugenol with spherical droplets smaller than 100nm, contrasting with the turbid emulsions prepared with individual emulsifiers. Zeta-potential data suggested the formation of LAE-lecithin complexes probably through hydrophobic interaction. Negligible difference was observed for antimicrobial activities of nanoemulsions and LAE in tryptic soy broth. In 2% reduced fat milk, nanoemulsions showed similar antilisterial activities compared to free LAE in inhibiting Listeria monocytogenes, but was less effective against Escherichia coli O157:H7 than free LAE, which was correlated with the availability of LAE as observed in release kinetics. Therefore, mixing LAE with lecithin improved the physical properties of EOC nanoemulsions but did not improve antimicrobial activities, especially against Gram-negative bacteria. Copyright © 2016 Elsevier Ltd. All rights reserved.

Bayesian sensitivity analysis of a 1D vascular model with Gaussian process emulators.

Science.gov (United States)

Melis, Alessandro; Clayton, Richard H; Marzo, Alberto

2017-12-01

One-dimensional models of the cardiovascular system can capture the physics of pulse waves but involve many parameters. Since these may vary among individuals, patient-specific models are difficult to construct. Sensitivity analysis can be used to rank model parameters by their effect on outputs and to quantify how uncertainty in parameters influences output uncertainty. This type of analysis is often conducted with a Monte Carlo method, where large numbers of model runs are used to assess input-output relations. The aim of this study was to demonstrate the computational efficiency of variance-based sensitivity analysis of 1D vascular models using Gaussian process emulators, compared to a standard Monte Carlo approach. The methodology was tested on four vascular networks of increasing complexity to analyse its scalability. The computational time needed to perform the sensitivity analysis with an emulator was reduced by the 99.96% compared to a Monte Carlo approach. Despite the reduced computational time, sensitivity indices obtained using the two approaches were comparable. The scalability study showed that the number of mechanistic simulations needed to train a Gaussian process for sensitivity analysis was of the order O(d), rather than O(d×103) needed for Monte Carlo analysis (where d is the number of parameters in the model). The efficiency of this approach, combined with capacity to estimate the impact of uncertain parameters on model outputs, will enable development of patient-specific models of the vascular system, and has the potential to produce results with clinical relevance. © 2017 The Authors International Journal for Numerical Methods in Biomedical Engineering Published by John Wiley & Sons Ltd.

Synchronous Parallel System for Emulation and Discrete Event Simulation

Science.gov (United States)

Steinman, Jeffrey S. (Inventor)

2001-01-01

A synchronous parallel system for emulation and discrete event simulation having parallel nodes responds to received messages at each node by generating event objects having individual time stamps, stores only the changes to the state variables of the simulation object attributable to the event object and produces corresponding messages. The system refrains from transmitting the messages and changing the state variables while it determines whether the changes are superseded, and then stores the unchanged state variables in the event object for later restoral to the simulation object if called for. This determination preferably includes sensing the time stamp of each new event object and determining which new event object has the earliest time stamp as the local event horizon, determining the earliest local event horizon of the nodes as the global event horizon, and ignoring events whose time stamps are less than the global event horizon. Host processing between the system and external terminals enables such a terminal to query, monitor, command or participate with a simulation object during the simulation process.

Emulating coupled atmosphere-ocean and carbon cycle models with a simpler model, MAGICC6 – Part 1: Model description and calibration

Directory of Open Access Journals (Sweden)

M. Meinshausen

2011-02-01

Full Text Available Current scientific knowledge on the future response of the climate system to human-induced perturbations is comprehensively captured by various model intercomparison efforts. In the preparation of the Fourth Assessment Report (AR4 of the Intergovernmental Panel on Climate Change (IPCC, intercomparisons were organized for atmosphere-ocean general circulation models (AOGCMs and carbon cycle models, named "CMIP3" and "C⁴MIP", respectively. Despite their tremendous value for the scientific community and policy makers alike, there are some difficulties in interpreting the results. For example, radiative forcings were not standardized across the various AOGCM integrations and carbon cycle runs, and, in some models, key forcings were omitted. Furthermore, the AOGCM analysis of plausible emissions pathways was restricted to only three SRES scenarios. This study attempts to address these issues. We present an updated version of MAGICC, the simple carbon cycle-climate model used in past IPCC Assessment Reports with enhanced representation of time-varying climate sensitivities, carbon cycle feedbacks, aerosol forcings and ocean heat uptake characteristics. This new version, MAGICC6, is successfully calibrated against the higher complexity AOGCMs and carbon cycle models. Parameterizations of MAGICC6 are provided. The mean of the emulations presented here using MAGICC6 deviates from the mean AOGCM responses by only 2.2% on average for the SRES scenarios. This enhanced emulation skill in comparison to previous calibrations is primarily due to: making a "like-with-like comparison" using AOGCM-specific subsets of forcings; employing a new calibration procedure; as well as the fact that the updated simple climate model can now successfully emulate some of the climate-state dependent effective climate sensitivities of AOGCMs. The diagnosed effective climate sensitivity at the time of CO₂ doubling for the AOGCMs is on average 2.88 °C, about

Application of the dynamically allocated virtual clustering management system to emulated tactical network experimentation

Science.gov (United States)

Marcus, Kelvin

2014-06-01

The U.S Army Research Laboratory (ARL) has built a "Network Science Research Lab" to support research that aims to improve their ability to analyze, predict, design, and govern complex systems that interweave the social/cognitive, information, and communication network genres. Researchers at ARL and the Network Science Collaborative Technology Alliance (NS-CTA), a collaborative research alliance funded by ARL, conducted experimentation to determine if automated network monitoring tools and task-aware agents deployed within an emulated tactical wireless network could potentially increase the retrieval of relevant data from heterogeneous distributed information nodes. ARL and NS-CTA required the capability to perform this experimentation over clusters of heterogeneous nodes with emulated wireless tactical networks where each node could contain different operating systems, application sets, and physical hardware attributes. Researchers utilized the Dynamically Allocated Virtual Clustering Management System (DAVC) to address each of the infrastructure support requirements necessary in conducting their experimentation. The DAVC is an experimentation infrastructure that provides the means to dynamically create, deploy, and manage virtual clusters of heterogeneous nodes within a cloud computing environment based upon resource utilization such as CPU load, available RAM and hard disk space. The DAVC uses 802.1Q Virtual LANs (VLANs) to prevent experimentation crosstalk and to allow for complex private networks. Clusters created by the DAVC system can be utilized for software development, experimentation, and integration with existing hardware and software. The goal of this paper is to explore how ARL and the NS-CTA leveraged the DAVC to create, deploy and manage multiple experimentation clusters to support their experimentation goals.

Self-double-emulsifying drug delivery system (SDEDDS): a new way for oral delivery of drugs with high solubility and low permeability.

Science.gov (United States)

Qi, Xiaole; Wang, Lishuang; Zhu, Jiabi; Hu, Zhenyi; Zhang, Jie

2011-05-16

Water-in-oil-in-water (w/o/w) double emulsions are potential for enhancing oral bioavailability of drugs with high solubility and low permeability, but their industrial application is limited due to the instability. Herein, we developed a novel formulation, self-double-emulsifying drug delivery systems (SDEDDS) by formulating mixtures of hydrophilic surfactants and water-in-oil (w/o) emulsions, which were easier to be stable through formulations optimization. SDEDDS can spontaneously emulsify to water-in-oil-in-water (w/o/w) double emulsions in the mixed aqueous gastrointestinal environment, with drugs encapsulated in the internal water phase of the double emulsions. We employed SDEDDS to improve the oral absorption of pidotimod, a peptide-like drug with high solubility and low permeability. The optimized pidotimod-SDEDDS were found to be stable up to 6 months under 25°C. Plasma concentration-time profiles from pharmacokinetic studies in rats dosed with SDEDDS showed 2.56-fold (p<0.05) increased absorption of pidotimod, compared to the pidotimod solution. Histopathologic studies confirmed that SDEDDS exerted absorption promoting effect without serious local damages. These studies demonstrate that SDEDDS may be a promising strategy for peroral delivery of peptide and peptidomimetic drugs. Copyright © 2011 Elsevier B.V. All rights reserved.

Conjunctively optimizing flash flood control and water quality in urban water reservoirs by model predictive control and dynamic emulation

Science.gov (United States)

Galelli, Stefano; Goedbloed, Albert; Schmitter, Petra; Castelletti, Andrea

2014-05-01

Urban water reservoirs are a viable adaptation option to account for increasing drinking water demand of urbanized areas as they allow storage and re-use of water that is normally lost. In addition, the direct availability of freshwater reduces pumping costs and diversifies the portfolios of drinking water supply. Yet, these benefits have an associated twofold cost. Firstly, the presence of large, impervious areas increases the hydraulic efficiency of urban catchments, with short time of concentration, increased runoff rates, losses of infiltration and baseflow, and higher risk of flash floods. Secondly, the high concentration of nutrients and sediments characterizing urban discharges is likely to cause water quality problems. In this study we propose a new control scheme combining Model Predictive Control (MPC), hydro-meteorological forecasts and dynamic model emulation to design real-time operating policies that conjunctively optimize water quantity and quality targets. The main advantage of this scheme stands in its capability of exploiting real-time hydro-meteorological forecasts, which are crucial in such fast-varying systems. In addition, the reduced computational requests of the MPC scheme allows coupling it with dynamic emulators of water quality processes. The approach is demonstrated on Marina Reservoir, a multi-purpose reservoir located in the heart of Singapore and characterized by a large, highly urbanized catchment with a short (i.e. approximately one hour) time of concentration. Results show that the MPC scheme, coupled with a water quality emulator, provides a good compromise between different operating objectives, namely flood risk reduction, drinking water supply and salinity control. Finally, the scheme is used to assess the effect of source control measures (e.g. green roofs) aimed at restoring the natural hydrological regime of Marina Reservoir catchment.

Emulating galaxy clustering and galaxy-galaxy lensing into the deeply nonlinear regime: methodology, information, and forecasts

OpenAIRE

Wibking, Benjamin D.; Salcedo, Andrés N.; Weinberg, David H.; Garrison, Lehman H.; Ferrer, Douglas; Tinker, Jeremy; Eisenstein, Daniel; Metchnik, Marc; Pinto, Philip

2017-01-01

The combination of galaxy-galaxy lensing (GGL) with galaxy clustering is one of the most promising routes to determining the amplitude of matter clustering at low redshifts. We show that extending clustering+GGL analyses from the linear regime down to $\\sim 0.5 \\, h^{-1}$ Mpc scales increases their constraining power considerably, even after marginalizing over a flexible model of non-linear galaxy bias. Using a grid of cosmological N-body simulations, we construct a Taylor-expansion emulator ...

Technical study on semi-object emulation of structural statics problem

CERN Document Server

MoJun; LiuXingFu; LiuZhiYong; Shi Pin Gan

2002-01-01

Structural strength analysis depends mainly on finite element method and experiments. For complex structural system, a rather large error can be caused by some uncertain factors, such as load distributions, boundary conditions and constitutive relations in numerical analysis. At the same time, owing to the limitation of measuring and testing techniques, the strength and stiffness of key components can not be estimated by using the limited test data. To simulate stresses accurately under complex static environment, improve man-machine interactive system, and make the best use of fore- and post-processing function in graphic data processing, the combine numerical analysis with experimental technique and have developed the semi-object emulation technique to analyze the nonlinear problem of structure statics. The modern optical measuring techniques and image processing techniques are firstly used for the method to acquire displacement data of the vessel surface, and the data are used for the boundary condition to...

Antibacterial Activity of Emulsified Pomelo (Citrus grandis Osbeck Peel Oil and Water-Soluble Chitosan on Staphylococcus aureus and Escherichia coli

Directory of Open Access Journals (Sweden)

Guan-Wen Chen

2018-04-01

Full Text Available This study utilized pomelo steam distillation to isolate pomelo peel essential oil. The constituents were then analyzed through gas chromatography-mass spectrometry (GC-MS, and the antibacterial activity of the essential oil emulsions at different homogenizer speed conditions and concentrations of water-soluble chitosan (degree of acetylation, DA = 54.8% against S. aureus and E. coli was examined. Analysis of the essential oil composition identified a total of 33 compounds with the main constituent, limonene accounting for 87.5% (940.07 mg/g of the total. The pomelo peel oil was emulsified through homogenization at 24,000 rpm, resulting in a minimal inhibitory concentration (MIC for E. coli that was 1.9 times lower than that of the essential oil without homogenization. In addition, a mixture of 0.4% essential oil emulsion and 0.03% water-soluble chitosan had the strongest synergetic antibacterial effect on S. aureus and E. coli at pH 7.4. In comparison with chitosan alone, the MIC value of this mixture was significantly 2.4 and 2.5 times lower. Hence, this study suggests using a mixture of emulsified pomelo peel oil and water-soluble chitosan to develop a novel natural food preservative, and that the processability of food, as well as the economic value of the byproducts of the Taiwan Matou pomelo and chitosan, could be increased.

Novel solid self-emulsifying drug delivery system of coenzyme Q₁₀ with improved photochemical and pharmacokinetic behaviors.

Science.gov (United States)

Onoue, Satomi; Uchida, Atushi; Kuriyama, Kazuki; Nakamura, Tatsuya; Seto, Yoshiki; Kato, Masashi; Hatanaka, Junya; Tanaka, Toshiyuki; Miyoshi, Hiroyuki; Yamada, Shizuo

2012-08-15

The present study was undertaken to develop a solid self-emulsifying drug delivery system of coenzyme Q(10) (CoQ(10)/s-SEDDS) with high photostability and oral bioavailability. The CoQ(10)/s-SEDDS was prepared by spray-drying an emulsion preconcentrate containing CoQ(10), medium-chain triglyceride, sucrose ester of fatty acid, and hydroxypropyl cellulose, and its physicochemical, photochemical, and pharmacokinetic properties were evaluated. The CoQ(10)/s-SEDDS powder with a diameter of ca. 15 μm was obtained by spray-drying, in which the CoQ(10) was mostly amorphized. The CoQ(10)/s-SEDDS exhibited immediate self-emulsification when introduced to aqueous media under gentle agitation, forming uniform fine droplets with a mean diameter of ca. 280 nm. There was marked generation of reactive oxygen species, in particular superoxide, from CoQ(10) exposed to simulated sunlight (250W/m(2)), suggesting potent photoreactivity. Nano-emulsified solution of CoQ(10) under light exposure underwent photodegradation with 22-fold higher degradation kinetics than crystalline CoQ(10), although the CoQ(10)/s-SEDDS was less photoreactive. After the oral administration of CoQ(10)/s-SEDDS (100 mg-CoQ(10)/kg) in rats, enhanced exposure of CoQ(10) was observed with increases in both C(max) and AUC of ca. 5-fold in comparison with those of orally administered crystalline CoQ(10). From the improved physicochemical and pharmacokinetic data, the s-SEDDS approach upon spray-drying might be a suitable dosage option for enhancing nutraceutical and pharmaceutical values of CoQ(10). Copyright © 2012 Elsevier B.V. All rights reserved.

A comparison of the stability of beverage cloud emulsions formulated with different gum acacia- and starch-based emulsifiers.

Science.gov (United States)

Reiner, S J; Reineccius, G A; Peppard, T L

2010-06-01

The performance of several hydrocolloids (3 gum acacias, 1 modified gum acacia, and 3 modified starches) in stabilizing beverage emulsions and corresponding model beverages was investigated employing different core materials, emulsifier usage levels, and storage temperatures. Concentrated emulsions were prepared using orange terpenes or Miglyol 812 (comprising medium-chain triglycerides, MCT) weighted 1:1 with ester gum, stored at 25 or 35 degrees C, and analyzed on days 0, 1, and 3. On day 3, model beverages were made from each emulsion, stored at both temperatures, and analyzed weekly for 4 wk. Stability of concentrated emulsions was assessed by measuring mean particle size and by visual observations of ringing; beverage stability was judged similarly and also by loss of turbidity. Particle size measurements showed concentrated emulsions containing gum acacia or modified gum acacia with either core material were stable over 3 d storage at both temperatures whereas those made with modified starches were not, destabilization being faster at 35 degrees C. Beverages based on orange terpenes, in contrast to Miglyol, yielded smaller mean particle sizes, both on manufacture and during storage, regardless of hydrocolloid used. Visual observations of ringing generally supported this finding. Modified gum acacia was evaluated at both recommended and higher usage levels, stability increasing in the latter case. In general, all gum acacia and modified gum acacia emulsifiers were superior in stability to those based on modified starches, at either temperature, for orange terpene-based beverages. In Miglyol-based beverages, similar results were seen, except 1 modified starch performed as well as the gum acacia products.

Microbial biodiversity of Tang and Pirgal mud volcanoes and evaluation of bio-emulsifier and bio-demulsifier activities of Capnophile bacteria.

Science.gov (United States)

Parsia, Yasaman; Sorooshian, Shahryar

2017-12-01

The data presented in this article is related to the Master thesis; entitled "Survey Aerobic Microbial Diversity Mud Volcanoes in Chabahar and Khash Ports in Southern Iran" by the first author of this article, year 2011, Islamic Azad University, Iran (reference number (Parsia, 2011) [1] of this article). This article shows microbial biodiversity and evaluates bio-emulsifier and bio-demulsifier abilities of capnophile isolates, in order to introduce a superior isolate for the Microbial Enhanced Oil Recovery (MEOR) process in the petrochemical industry.

Pseudo-random generator to allow to an electronic pulse simulator the ability to emulate radioisotopes spectra

International Nuclear Information System (INIS)

Lucianna F A; Carrillo M A; Mangussi M J

2012-01-01

The present work describes the development of a pseudo-random system to provide to a simulator pulse of radiation detectors the ability to emit pulses patterns similar to those recorded when measuring actual radioisotope. The idea is that the system can emulate characteristic spectral distributions of known radioisotopes, as well as creating individual spectra for specific purposes. This design is based on an improvement in terms of software from earlier development that only supplied predefined amplitude pulses at constant intervals (author)

Space Link Extension Protocol Emulation for High-Throughput, High-Latency Network Connections

Science.gov (United States)

Tchorowski, Nicole; Murawski, Robert

2014-01-01

New space missions require higher data rates and new protocols to meet these requirements. These high data rate space communication links push the limitations of not only the space communication links, but of the ground communication networks and protocols which forward user data to remote ground stations (GS) for transmission. The Consultative Committee for Space Data Systems, (CCSDS) Space Link Extension (SLE) standard protocol is one protocol that has been proposed for use by the NASA Space Network (SN) Ground Segment Sustainment (SGSS) program. New protocol implementations must be carefully tested to ensure that they provide the required functionality, especially because of the remote nature of spacecraft. The SLE protocol standard has been tested in the NASA Glenn Research Center's SCENIC Emulation Lab in order to observe its operation under realistic network delay conditions. More specifically, the delay between then NASA Integrated Services Network (NISN) and spacecraft has been emulated. The round trip time (RTT) delay for the continental NISN network has been shown to be up to 120ms; as such the SLE protocol was tested with network delays ranging from 0ms to 200ms. Both a base network condition and an SLE connection were tested with these RTT delays, and the reaction of both network tests to the delay conditions were recorded. Throughput for both of these links was set at 1.2Gbps. The results will show that, in the presence of realistic network delay, the SLE link throughput is significantly reduced while the base network throughput however remained at the 1.2Gbps specification. The decrease in SLE throughput has been attributed to the implementation's use of blocking calls. The decrease in throughput is not acceptable for high data rate links, as the link requires constant data a flow in order for spacecraft and ground radios to stay synchronized, unless significant data is queued a the ground station. In cases where queuing the data is not an option

Influence of the formulation type (o/w, w/o/w emulsions and ointment on the topical delivery of paromomycin Influência da forma farmacêutica (emulsão múltipla A/O/A, emulsão O/A e pomada sobre a permeação e retenção cutânea da paromomicina

Directory of Open Access Journals (Sweden)

Sérgio Fernandes de Oliveira Gomes

2004-09-01

Full Text Available Ointments containing paromomycin (PA have been used for topical treatment of cutaneous leishmaniasis. Although influence of the vehicle on skin permeation is crucial for optimization of formulations containing PA, this aspect has not been investigated experimentally. In this study, we have evaluated the influence of the formulation type [oil-in-water (o/w, water-in-oil-in-water (w/o/w emulsions and ointment] on in vitro release and skin permeation of PA and experiments were carried out on cellulose acetate membrane and skin biopsies from hairless mice, respectively. PA release from o/w emulsion (51.7% ± 0.9 of dose applied was faster than that observed for w/o/w emulsion (3.0% ± 0.5. PA absorption from o/w emulsion (87.1% ± 3.9 through stripped skin was 5 to 6 times higher than that observed for w/o/w multiple emulsion (14.7% ± 0.5 and ointment (16.6% ± 0.1. PA permeation through intact (normal skin was negligible for all tested formulations. Skin uptake from o/w emulsion (0.9% ± 0.1 was greater than that observed for w/o/w multiple emulsion (0.3% ± 0.1 and ointment (0.1% ± 0.1. These results suggest that a hydrophilic vehicle (o/w emulsion could be an interesting alternative to improve topical delivery of PA.Pomadas contendo paromomicina (PA são utilizadas no tratamento tópico da leishmaniose cutânea. Embora a influência do veículo seja crucial para otimização de formulações contendo PA, este aspecto não tem sido investigado experimentalmente. Neste estudo, nós avaliamos a influência do tipo de formulação [emulsões óleo-em-água (o/a, múltipla água-em-óleo-em-água (a/o/a e pomadas] sobre a liberação e permeação cutânea in vitro da PA e os experimentos foram conduzidos sobre membranas de acetato de celulose e biópsias de pele de camundongos glabros, respectivamente. A liberação de PA a partir da emulsão o/a (51,7% da dose aplicada foi mais rápida do que aquela observada a partir da emulsão múltipla a

Retaining Oxidative Stability of Emulsified Foods by Novel Nonmigratory Polyphenol Coated Active Packaging.

Science.gov (United States)

Roman, Maxine J; Decker, Eric A; Goddard, Julie M

2016-07-13

Oxidation causes lipid rancidity, discoloration, and nutrient degradation that decrease shelf life of packaged foods. Synthetic additives are effective oxidation inhibitors, but are undesirable to consumers who prefer "clean" label products. The aim of this study was to improve oxidative stability of emulsified foods by a novel nonmigratory polyphenol coated active packaging. Polyphenol coatings were applied to chitosan functionalized polypropylene (PP) by laccase assisted polymerization of catechol and catechin. Polyphenol coated PP exhibited both metal chelating (39.3 ± 2.5 nmol Fe(3+) cm(-2), pH 4.0) and radical scavenging (up to 52.9 ± 1.8 nmol Trolox eq cm(-2)) capacity, resulting in dual antioxidant functionality to inhibit lipid oxidation and lycopene degradation in emulsions. Nonmigratory polyphenol coated PP inhibited ferric iron promoted degradation better than soluble chelators, potentially by partitioning iron from the emulsion droplet interface. This work demonstrates that polyphenol coatings can be designed for advanced material chemistry solutions in active food packaging.

In vitro and in vivo performance of monoacyl phospholipid-based self-emulsifying drug delivery systems

DEFF Research Database (Denmark)

Tran, Thuy; Siqueira, Scheyla D V S; Amenitsch, Heinz

2017-01-01

to investigate the impact of LPC on the emulsion droplet size, extent of digestion, colloidal structure evolution and drug precipitation during in vitro lipolysis simulating human conditions and drug bioavailability in a rat model. The four investigated SEDDS containing long-chain glycerides, polyoxyl 35 castor...... and polydispersity of the dispersed SEDDS. The two LPC-free SEDDS generated lamellar phase structures (Lα) with d-spacing=4.76nm during digestion. Incorporating LPC into these systems inhibited the formation of lamellar phase structures. The amount of precipitated crystalline FF from the four SEDDS was similar......This study investigates the effect of monoacyl phospholipid incorporation on the in vitro and in vivo performance of self-emulsifying drug delivery systems (SEDDS). Monoacyl phosphatidylcholine (Lipoid S LPC 80 (LPC)) was incorporated into four different fenofibrate (FF)-loaded long-chain SEDDS...

Combined high-power ultrasound and high-pressure homogenization nanoemulsification: The effect of energy density, oil content and emulsifier type and content.

Science.gov (United States)

Calligaris, Sonia; Plazzotta, Stella; Valoppi, Fabio; Anese, Monica

2018-05-01

Combinations of ultrasound (US) and high-pressure homogenization (HPH) at low-medium energy densities were studied as alternative processes to individual US and HPH to produce Tween 80 and whey protein stabilized nanoemulsions, while reducing the energy input. To this aim, preliminary trials were performed to compare emulsification efficacy of single and combined HPH and US treatments delivering low-medium energy densities. Results highlighted the efficacy of US-HPH combined process in reducing the energy required to produce nanoemulsions stabilized with both Tween 80 and whey protein isolate. Subsequently, the effect of emulsifier content (1-3% w/w), oil amount (10-20% w/w) and energy density (47-175 MJ/m 3 ) on emulsion mean particle diameter was evaluated by means of a central composite design. Particles of 140-190 nm were obtained by delivering 175 MJ/m 3 energy density at emulsions containing 3% (w/w) Tween 80 and 10% (w/w) oil. In the case of whey protein isolate stabilized emulsions, a reduced emulsifier amount (1% w/w) and intermediate energy density (120 MJ/m 3 ) allowed a minimum droplet size around 220-250 nm to be achieved. Results showed that, in both cases, at least 50% of the energy density should be delivered by HPH to obtain the minimum particle diameter. Copyright © 2018 Elsevier Ltd. All rights reserved.

Emulation of Physician Tasks in Eye-Tracked Virtual Reality for Remote Diagnosis of Neurodegenerative Disease.

Science.gov (United States)

Orlosky, Jason; Itoh, Yuta; Ranchet, Maud; Kiyokawa, Kiyoshi; Morgan, John; Devos, Hannes

2017-04-01

For neurodegenerative conditions like Parkinson's disease, early and accurate diagnosis is still a difficult task. Evaluations can be time consuming, patients must often travel to metropolitan areas or different cities to see experts, and misdiagnosis can result in improper treatment. To date, only a handful of assistive or remote methods exist to help physicians evaluate patients with suspected neurological disease in a convenient and consistent way. In this paper, we present a low-cost VR interface designed to support evaluation and diagnosis of neurodegenerative disease and test its use in a clinical setting. Using a commercially available VR display with an infrared camera integrated into the lens, we have constructed a 3D virtual environment designed to emulate common tasks used to evaluate patients, such as fixating on a point, conducting smooth pursuit of an object, or executing saccades. These virtual tasks are designed to elicit eye movements commonly associated with neurodegenerative disease, such as abnormal saccades, square wave jerks, and ocular tremor. Next, we conducted experiments with 9 patients with a diagnosis of Parkinson's disease and 7 healthy controls to test the system's potential to emulate tasks for clinical diagnosis. We then applied eye tracking algorithms and image enhancement to the eye recordings taken during the experiment and conducted a short follow-up study with two physicians for evaluation. Results showed that our VR interface was able to elicit five common types of movements usable for evaluation, physicians were able to confirm three out of four abnormalities, and visualizations were rated as potentially useful for diagnosis.

A Voice-Detecting Sensor and a Scanning Keyboard Emulator to Support Word Writing by Two Boys with Extensive Motor Disabilities

Science.gov (United States)

Lancioni, Giulio E.; Singh, Nirbhay N.; O'Reilly, Mark F.; Sigafoos, Jeff; Green, Vanessa; Chiapparino, Claudia; Stasolla, Fabrizio; Oliva, Doretta

2009-01-01

The present study assessed the use of a voice-detecting sensor interfaced with a scanning keyboard emulator to allow two boys with extensive motor disabilities to write. Specifically, the study (a) compared the effects of the voice-detecting sensor with those of a familiar pressure sensor on the boys' writing time, (b) checked which of the sensors…

Inhibitory effect of BCG cell-wall skeletons (BCG-CWS) emulsified in squalane on tumor growth and metastasis in mice.

Science.gov (United States)

Yoo, Yung Choon; Hata, Katsusuke; Lee, Kyung Bok; Azuma, Ichiro

2002-08-01

The antimetastatic effect of BCG-CWS, which was emulsified in an oil-in-water form with either Drakeol 6VR mineral oil (BCG-CWS/DK) or squalane (BCG-CWS/SQA), on lung metastasis produced by highly metastatic murine tumor cells, Colon26-M3.1 carcinoma cells and B16-BL6 melanoma cells, was investigated in syngeneic mice. An intravenous (i.v.) administration of BCG-CWS (100 mg/mouse) 1 day after tumor inoculation significantly inhibited tumor metastasis of both Colon26-M3.1 carcinoma and B16-BL6 melanoma cells in experimental lung metastasis models. No differences in the antitumor activity of the two oil-based formulations (BCG-CWS/DK and BCG-CWS/SQA) were obverved. However, BCG-CWS/SQA administered through subcutaneous (s.c.) route was shown to be effective only when it was consecutively injected (3 times) after tumor inoculation. An in vivo analysis for tumor-induced angiogenesis showed that a single i.v. administration of BCG-CWS/SQA inhibited the number of tumor-induced blood vessels and suppressed tumor growth. Furthermore, the multiple administration of BCG-CWS/SQA given at on week intervals led to a significant reduction in spontaneous lung metastasis of B16-BL6 melanoma cells in a spontaneous metastasis model. These results suggest that BCG-CWS emulsified with squalane is a potent inhibitory agent of lung metastasis, and that the antimetastatic effect of BCG-CWS is related to the suppression of tumor growth and the inhibition of tumor-induced angiogenesis.

AC Transmission Emulation Control Strategies for the BTB VSC HVDC System in the Metropolitan Area of Seoul

Directory of Open Access Journals (Sweden)

Sungyoon Song

2017-08-01

Full Text Available In the Korean power system, growing power loads have recently created the problems of voltage instability and fault current in the Seoul Capital Area (SCA. Accordingly, the back-to-back (BTB voltage source converter (VSC high-voltage direct-current (HVDC system is emerging to resolve such problems with grid segmentation. However, non-convergence problems occur in this metropolitan area, due to the large change of power flow in some contingencies. Therefore, this paper proposes two kinds of AC transmission emulation control (ATEC strategies to improve the metropolitan transient stability, and to resolve the non-convergence problem. The proposed ATEC strategies are able to mitigate possible overloading of adjacent AC transmission, and maintain power balance between metropolitan regions. The first ATEC strategy uses a monitoring system that permits the reverse power flow of AC transmission, and thus effectively improves the grid stability based on the power transfer equation. The second ATEC strategy emulates AC transmission with DC link capacitors in a permissible DC-link voltage range according to angle difference, and securely improves the gird stability, without requiring grid operator schedule decisions. This paper compares two kinds of ATEC schemes: it demonstrates the first ATEC strategy with specific fault scenario with PSS/E (Power Transmission System Planning Software, and evaluates the second ATEC strategy with internal controller performance with PSCAD/EMTDC (Power System Electromagnetic Transients Simulation Software.

Integrated process for the removal of emulsified oils from effluents in the steel industry

Energy Technology Data Exchange (ETDEWEB)

Benito, J.M.; Rios, G.; Gutierrez, B.; Pazos, C.; Coca, J.

1999-11-01

Emulsified oils contained in aqueous effluents from cold-rolling mills of the steel industry can be effectively removed via an integrated process consisting of a coagulation/flocculation stage followed by ultrafiltration of the resulting aqueous phase. The effects of CaCl{sub 2}, NaOH, and lime on the stability of different industrial effluents were studied in the coagulation experiments. The flocculants tested were inorganic prehydrolyzed aluminum salts and quaternary polyamines. Ultrafiltration of the aqueous phase from the coagulation/flocculation stage was carried out in a stirred cell using Amicon PM30 and XM300 organic membranes. Permeate fluxes were measured for industrial effluents to which the indicated coagulants and flocculants had been added. Oil concentrations in the permeate were 75% lower than the limits established by all European Union countries. Complete regeneration of the membrane was accomplished with an aqueous solution of a commercial detergent.

Influence of Casein-Phospholipid Combinations as Emulsifier on the Physical and Oxidative Stability of Fish Oil-in-Water Emulsions

DEFF Research Database (Denmark)

García Moreno, Pedro Jesús; Horn, Anna Frisenfeldt; Jacobsen, Charlotte

2014-01-01

The objective of this study was to investigate the influence of casein (0.3% w/w) and phospholipid (0.5% w/w) emulsifier combinations on the physical and oxidative stability of 10% fish oil-in-water emulsions at pH 7. For that purpose, three phospholipids were evaluated, namely, lecithin (LC......), phosphatidylcholine (PC), and phosphatidylethanolamine (PE). The emulsion stabilized with LC showed the best physical stability having the most negative zeta potential and the lowest mean droplet size. In addition, this emulsion was also the least oxidized in terms of peroxide value and concentration of the volatile...

A Numerical Comparison of Spray Combustion between Raw and Water-in-Oil Emulsified Fuel

Directory of Open Access Journals (Sweden)

D. Tarlet

2010-03-01

Full Text Available Heavy fuel-oils, used engine oils and animal fat can be used as dense, viscous combustibles within industrial boilers. Burning these combustibles in the form of an emulsion with water enables to decrease the flame length and the formation of carbonaceous residue, in comparison with raw combustibles. These effects are due to the secondary atomization among the spray, which is a consequence of the micro-explosion phenomenon. This phenomenon acts in a single emulsion droplet by the fast (< 0.1 ms vaporization of the inside water droplets, leading to complete disintegration of the whole emulsion droplet. First, the present work demonstrates a model of spray combustion of raw fuel. Secondly, the spray combustion of water-in-oil emulsified fuel is exposed to the same burning conditions, taking into account the micro-explosion phenomenon. Finally, the comparison between the results with and without second atomization shows some similar qualitative tendencies with experimental measurements from the literature.

Disintegration and cancer immunotherapy efficacy of a squalane-in-water delivery system emulsified by bioresorbable poly(ethylene glycol)-block-polylactide.

Science.gov (United States)

Chen, Wei-Lin; Liu, Shih-Jen; Leng, Chih-Hsiang; Chen, Hsin-Wei; Chong, Pele; Huang, Ming-Hsi

2014-02-01

Vaccine adjuvant is conferred on the substance that helps to enhance antigen-specific immune response. Here we investigated the disintegration characteristics and immunotherapy potency of an emulsified delivery system comprising bioresorbable polymer poly(ethylene glycol)-polylactide (PEG-PLA), phosphate buffer saline (PBS), and metabolizable oil squalane. PEG-PLA-stabilized oil-in-water emulsions show good stability at 4 °C and at room temperature. At 37 °C, squalane/PEG-PLA/PBS emulsion with oil/aqueous weight ratio of 7/3 (denominated PELA73) was stable for 6 weeks without phase separation. As PEG-PLA being degraded, 30% of free oil at the surface layer and 10% of water at the bottom disassociated from the PELA73 emulsion were found after 3 months. A MALDI-TOF MS study directly on the DIOS plate enables us to identify low molecular weight components released during degradation. Our results confirm the loss of PLA moiety of the emulsifier PEG-PLA directly affected the stability of PEG-PLA-stabilized emulsion, leading to emulsion disintegration and squalane/water phase separation. As adjuvant for cancer immunotherapeutic use, an HPV16 E7 peptide antigen formulated with PELA73 plus immunostimulatory CpG molecules could strongly enhance antigen-specific T-cell responses as well as anti-tumor ability with respected to non-formulated or Alum-formulated peptide. Accordingly, these advances may be a potential immunoregulatory strategy in manipulating the immune responses induced by tumor-associated antigens. Copyright © 2013 The Authors. Published by Elsevier Ltd.. All rights reserved.

Emulating atmosphere-ocean and carbon cycle models with a simpler model, MAGICC6 – Part 2: Applications

Directory of Open Access Journals (Sweden)

M. Meinshausen

2011-02-01

Full Text Available Intercomparisons of coupled atmosphere-ocean general circulation models (AOGCMs and carbon cycle models are important for galvanizing our current scientific knowledge to project future climate. Interpreting such intercomparisons faces major challenges, not least because different models have been forced with different sets of forcing agents. Here, we show how an emulation approach with MAGICC6 can address such problems. In a companion paper (Meinshausen et al., 2011a, we show how the lower complexity carbon cycle-climate model MAGICC6 can be calibrated to emulate, with considerable accuracy, globally aggregated characteristics of these more complex models. Building on that, we examine here the Coupled Model Intercomparison Project's Phase 3 results (CMIP3. If forcing agents missed by individual AOGCMs in CMIP3 are considered, this reduces ensemble average temperature change from pre-industrial times to 2100 under SRES A1B by 0.4 °C. Differences in the results from the 1980 to 1999 base period (as reported in IPCC AR4 to 2100 are negligible, however, although there are some differences in the trajectories over the 21st century. In a second part of this study, we consider the new RCP scenarios that are to be investigated under the forthcoming CMIP5 intercomparison for the IPCC Fifth Assessment Report. For the highest scenario, RCP8.5, relative to pre-industrial levels, we project a median warming of around 4.6 °C by 2100 and more than 7 °C by 2300. For the lowest RCP scenario, RCP3-PD, the corresponding warming is around 1.5 °C by 2100, decreasing to around 1.1 °C by 2300 based on our AOGCM and carbon cycle model emulations. Implied cumulative CO₂ emissions over the 21st century for RCP8.5 and RCP3-PD are 1881 GtC (1697 to 2034 GtC, 80% uncertainty range and 381 GtC (334 to 488 GtC, when prescribing CO₂ concentrations and accounting for uncertainty in the carbon cycle. Lastly, we assess the reasons why a previous MAGICC

Vitamin E TPGS emulsified vinorelbine bitartrate loaded solid lipid nanoparticles (SLN): Formulation development, optimization and in vitro characterization.

Science.gov (United States)

Maurya, Lakshmi; Rajamanickam, Vijayakumar Mahalingam; Narayan, Gopeshwar; Singh, Sanjay

2018-04-08

Vinorelbine bitartrate (VRL), a semi synthetic vinca alkaloid approved for breast cancer, has been proved to beneficial as first line and subsequent therapies. However, it's hydrophilic and thermo labile nature provides hindrance to oral clinical translation. The current work focused on the application of DOE a modern statistical optimization tool for the development and optimization of a solid lipid nanoparticle (SLN) formulation that can encapsulate hydrophilic and thermolabile Vinorelbine bitartrate (VRL) to a maximum extent without compromising integrity and anticancer activity of the drug. SLNs were prepared by solvent diffusion technique employing Taguchi orthogonal array design with optimized formulation and process variables. The emulsifying nature and low melting point of glyceryl mono-oleate (GMO) were exploited to enhance entrapment and minimizing temperature associated degradation, respectively. Moreover, two types of surfactants, Vitamin E TPGS (TPGS) and Poloxamer-188 were utilized to obtain TPGS-VRL-SLNs and PL-VRL-SLNs, respectively. The SLNs were characterized for various physicochemical properties, in-vitro drug release kinetics and anticancer activity by MTT assay on MCF-7 cancer cell lines. The SLNs were found to be spherical in shape with entrapment efficiency (EE) up to 58 %. In-vitro release studies showed biphasic release pattern following Korsemeyer peppas model with fickian release kinetics. Results of MTT assay revealed that TPGS-VRL-SLNs and PL-VRL-SLNs were 39.5 and 18.5 fold more effective, respectively, compared to the pristine VRL. DOE approach was successfully applied for the development of VRL-SLNs. Enhanced entrapment and anticancer efficacy of TPGS-VRL-SLN can be attributed to emulsifying nature of GMO and inherent cytotoxic nature of TPGS, respectively, which synergizes with VRL. Therefore, TPGS associated SLNs may be potential carrier in cancer chemotherapeutics. Copyright© Bentham Science Publishers; For any queries, please

On flotation separation of oxo-anions of transition metals by the use of fine-emulsified solutions of cationic collector in non-polar liquids

International Nuclear Information System (INIS)

Skrylev, L.D.; Purich, A.N.; Babinets, S.K.

1980-01-01

Experimentally shown is a principle possibility of flotation separation of oxo-anions of transition metals by the use of fine-emulsified solutions of cationic collector in non-polar liquids. Ammonium vanadate and sodium tuno.state solutions have been the objects of study. Hexadezilamine has been used as collector. The collector has been introduced in the form of hexadecylamine emulsions in n-decane, in tetrachloromethane or alcohol. Optimum pH value ranges are determined for separation processes

EFFECTS OF ω-ACRYLOYL POLY(ETHYLENE OXIDE) MACROMONOMER ON EMULSIFIER-FREE EMULSION COPOLYMERIZATION OF METHYL METHACRYLATE AND n-BUTYL ACRYLATE

Institute of Scientific and Technical Information of China (English)

无

1998-01-01

Well-defined nonionic hydrophilic ω-acryloyl poly(ethylene oxide) macromonomer (PEO-A) has been prepared by living anionic polymerization of ethylene oxide with diphenyl methyl potassium as the initiator and acryloyl chloride as the reaction terminating agent. The polymer was characterized by FTIR and SEC. The emulsifier-free emulsion polymerization of methyl methacrylate (MMA) and n-butyl acrylate (BA) containing various concentrations of PEO-A was studied. In all cases stable emulsion coplymerizations of MMA and BA were obtained. The stabilizing effect was found to be dependent on the molecular weight and the feed amount of the macromonomer.

Microbial biodiversity of Tang and Pirgal mud volcanoes and evaluation of bio-emulsifier and bio-demulsifier activities of Capnophile bacteria

Directory of Open Access Journals (Sweden)

Yasaman Parsia

2017-12-01

Full Text Available The data presented in this article is related to the Master thesis; entitled “Survey Aerobic Microbial Diversity Mud Volcanoes in Chabahar and Khash Ports in Southern Iran” by the first author of this article, year 2011, Islamic Azad University, Iran (reference number (Parsia, 2011 [1] of this article. This article shows microbial biodiversity and evaluates bio-emulsifier and bio-demulsifier abilities of capnophile isolates, in order to introduce a superior isolate for the Microbial Enhanced Oil Recovery (MEOR process in the petrochemical industry. Keywords: Mud volcanoes, Biodiversity, Bio-emulsification, Bio-demulsification, Petrochemistry

Emulating Host-Microbiome Ecosystem of Human Gastrointestinal Tract in Vitro.

Science.gov (United States)

Park, Gun-Seok; Park, Min Hee; Shin, Woojung; Zhao, Connie; Sheikh, Sameer; Oh, So Jung; Kim, Hyun Jung

2017-06-01

The human gut microbiome performs prodigious physiological functions such as production of microbial metabolites, modulation of nutrient digestion and drug metabolism, control of immune system, and prevention of infection. Paradoxically, gut microbiome can also negatively orchestrate the host responses in diseases or chronic disorders, suggesting that the regulated and balanced host-gut microbiome crosstalk is a salient prerequisite in gastrointestinal physiology. To understand the pathophysiological role of host-microbiome crosstalk, it is critical to recreate in vivo relevant models of the host-gut microbiome ecosystem in human. However, controlling the multi-species microbial communities and their uncontrolled growth has remained a notable technical challenge. Furthermore, conventional two-dimensional (2D) or 3D culture systems do not recapitulate multicellular microarchitectures, mechanical dynamics, and tissue-specific functions. Here, we review recent advances and current pitfalls of in vitro and ex vivo models that display human GI functions. We also discuss how the disruptive technologies such as 3D organoids or a human organ-on-a-chip microphysiological system can contribute to better emulate host-gut microbiome crosstalks in health and disease. Finally, the medical and pharmaceutical significance of the gut microbiome-based personalized interventions is underlined as a future perspective.

A methodology to emulate and evaluate a productive virtual workstation

Science.gov (United States)

Krubsack, David; Haberman, David

1992-01-01

The Advanced Display and Computer Augmented Control (ADCACS) Program at ACT is sponsored by NASA Ames to investigate the broad field of technologies which must be combined to design a 'virtual' workstation for the Space Station Freedom. This program is progressing in several areas and resulted in the definition of requirements for a workstation. A unique combination of technologies at the ACT Laboratory have been networked to effectively create an experimental environment. This experimental environment allows the integration of nonconventional input devices with a high power graphics engine within the framework of an expert system shell which coordinates the heterogeneous inputs with the 'virtual' presentation. The flexibility of the workstation is evolved as experiments are designed and conducted to evaluate the condition descriptions and rule sets of the expert system shell and its effectiveness in driving the graphics engine. Workstation productivity has been defined by the achievable performance in the emulator of the calibrated 'sensitivity' of input devices, the graphics presentation, the possible optical enhancements to achieve a wide field of view color image and the flexibility of conditional descriptions in the expert system shell in adapting to prototype problems.

A data-driven emulation framework for representing water-food nexus in a changing cold region

Science.gov (United States)

Nazemi, A.; Zandmoghaddam, S.; Hatami, S.

2017-12-01

Water resource systems are under increasing pressure globally. Growing population along with competition between water demands and emerging effects of climate change have caused enormous vulnerabilities in water resource management across many regions. Diagnosing such vulnerabilities and provision of effective adaptation strategies requires the availability of simulation tools that can adequately represent the interactions between competing water demands for limiting water resources and inform decision makers about the critical vulnerability thresholds under a range of potential natural and anthropogenic conditions. Despite a significant progress in integrated modeling of water resource systems, regional models are often unable to fully represent the contemplating dynamics within the key elements of water resource systems locally. Here we propose a data-driven approach to emulate a complex regional water resource system model developed for Oldman River Basin in southern Alberta, Canada. The aim of the emulation is to provide a detailed understanding of the trade-offs and interaction at the Oldman Reservoir, which is the key to flood control and irrigated agriculture in this over-allocated semi-arid cold region. Different surrogate models are developed to represent the dynamic of irrigation demand and withdrawal as well as reservoir evaporation and release individually. The nan-falsified offline models are then integrated through the water balance equation at the reservoir location to provide a coupled model for representing the dynamic of reservoir operation and water allocation at the local scale. The performance of individual and integrated models are rigorously examined and sources of uncertainty are highlighted. To demonstrate the practical utility of such surrogate modeling approach, we use the integrated data-driven model for examining the trade-off in irrigation water supply, reservoir storage and release under a range of changing climate, upstream

User's guide to the CALVEC software library: a computer program for emulation of CALCOMP graphics on a Versatec printer/plotter

International Nuclear Information System (INIS)

Gray, W.H.

1978-08-01

This document describes a set of FORTRAN subroutines collectively called the CALVEC subprogram library. The purpose of the CALVEC software library is the emulation of CALCOMP pen and ink graphics on a DECsystem 10. A user level interface with CALVEC software allows standard CALCOMP subprogram calls to produce a VECtor file, SEGMNT.VEC. This vector file may subsequently be postprocessed into an image in a variety of ways

User's guide to the CALVEC software library: a computer program for emulation of CALCOMP graphics on a versatec printer/plotter

International Nuclear Information System (INIS)

Gray, W.H.

1979-03-01

this document describes a set of FORTRAN subroutines collectively called the CALVEC subprogram library. The purpose of the CALVEC software library is the emulation of CALCOMP pen and ink graphics on a DECsystem 10. A user level interface with CALVEC software allows standard CALCOMP subprogram calls to produce a VECtor file, FOR24.VEC. This vector file may subsequently be postprocessed into an image in a variety of ways

The Prospects of Whole Brain Emulation within the next Half- Century

Science.gov (United States)

Eth, Daniel; Foust, Juan-Carlos; Whale, Brandon

2013-12-01

Whole Brain Emulation (WBE), the theoretical technology of modeling a human brain in its entirety on a computer-thoughts, feelings, memories, and skills intact-is a staple of science fiction. Recently, proponents of WBE have suggested that it will be realized in the next few decades. In this paper, we investigate the plausibility of WBE being developed in the next 50 years (by 2063). We identify four essential requisite technologies: scanning the brain, translating the scan into a model, running the model on a computer, and simulating an environment and body. Additionally, we consider the cultural and social effects of WBE. We find the two most uncertain factors for WBE's future to be the development of advanced miniscule probes that can amass neural data in vivo and the degree to which the culture surrounding WBE becomes cooperative or competitive. We identify four plausible scenarios from these uncertainties and suggest the most likely scenario to be one in which WBE is realized, and the technology is used for moderately cooperative ends

Emulating a crowded intracellular environment in vitro dramatically improves RT-PCR performance

International Nuclear Information System (INIS)

Lareu, Ricky R.; Harve, Karthik S.; Raghunath, Michael

2007-01-01

The polymerase chain reaction's (PCR) phenomenal success in advancing fields as diverse as Medicine, Agriculture, Conservation, or Paleontology is based on the ability of using isolated prokaryotic thermostable DNA polymerases in vitro to copy DNA irrespective of origin. This process occurs intracellularly and has evolved to function efficiently under crowded conditions, namely in an environment packed with macromolecules. However, current in vitro practice ignores this important biophysical parameter of life. In order to more closely emulate conditions of intracellular biochemistry in vitro we added inert macromolecules into reverse transcription (RT) and PCR. We show dramatic improvements in all parameters of RT-PCR including 8- to 10-fold greater sensitivity, enhanced polymerase processivity, higher specific amplicon yield, greater primer annealing and specificity, and enhanced DNA polymerase thermal stability. The faster and more efficient reaction kinetics was a consequence of the cumulative molecular and thermodynamic effects of the excluded volume effect created by macromolecular crowding

Design and building of home made 8051 micro controller emulator

International Nuclear Information System (INIS)

Hussein, A. E.

2009-09-01

This research targeted design and build of a simple lab made emulator for the 8051 micro controller to assist student and researcher in their projects. This will be achieved by thorough understanding of the software and the hardware of the development tool which will enhance the user knowledge rather than considering them as black boxes and unaware of their capabilities and their limitations. Regarding the hardware this work preferred to use the same central processing unit the developer wanted to build with little modification. While the software is a program loaded in the micro controller itself responsible (making use of flash micro controllers) for communication with the host computer terminal, and monitoring the user program which is loaded in external memory by the program. Any terminal program on the host computer can be used to carry out communication with monitor program provided that a carriage return should be pressed after monitor power up to let the monitor adjust its baud rate accordingly. This feature makes the monitor program so simple and familiar to the user. For simplicity the software is enhanced with flash programming and erasing subroutine which can allow the user to store his program there if he put a flash ROM in his hardware and he can make it as start up program which will run automatically after start up. Also many programs can be loaded in the flash as long as its capacity is capable. Definitely this requires configuring flash start and end in the source before compiling it. This flash feature allows the development hardware to be as final board and hence a debugable one as long as monitor program resides inside the micro controller. Considering the debugging stage as the most crucial step in the development cycle, this work tried to find some suitable and simple solutions that can enhance knowledge. As a result some commands on the user program like uploading, displaying, jumping, selecting among others, running, editing, clearing and

Using Machine Learning as a fast emulator of physical processes within the Met Office's Unified Model

Science.gov (United States)

Prudden, R.; Arribas, A.; Tomlinson, J.; Robinson, N.

2017-12-01

The Unified Model is a numerical model of the atmosphere used at the UK Met Office (and numerous partner organisations including Korean Meteorological Agency, Australian Bureau of Meteorology and US Air Force) for both weather and climate applications.Especifically, dynamical models such as the Unified Model are now a central part of weather forecasting. Starting from basic physical laws, these models make it possible to predict events such as storms before they have even begun to form. The Unified Model can be simply described as having two components: one component solves the navier-stokes equations (usually referred to as the "dynamics"); the other solves relevant sub-grid physical processes (usually referred to as the "physics"). Running weather forecasts requires substantial computing resources - for example, the UK Met Office operates the largest operational High Performance Computer in Europe - and the cost of a typical simulation is spent roughly 50% in the "dynamics" and 50% in the "physics". Therefore there is a high incentive to reduce cost of weather forecasts and Machine Learning is a possible option because, once a machine learning model has been trained, it is often much faster to run than a full simulation. This is the motivation for a technique called model emulation, the idea being to build a fast statistical model which closely approximates a far more expensive simulation. In this paper we discuss the use of Machine Learning as an emulator to replace the "physics" component of the Unified Model. Various approaches and options will be presented and the implications for further model development, operational running of forecasting systems, development of data assimilation schemes, and development of ensemble prediction techniques will be discussed.

Efficient and robust gradient enhanced Kriging emulators.

Energy Technology Data Exchange (ETDEWEB)

Dalbey, Keith R.

2013-08-01

%E2%80%9CNaive%E2%80%9D or straight-forward Kriging implementations can often perform poorly in practice. The relevant features of the robustly accurate and efficient Kriging and Gradient Enhanced Kriging (GEK) implementations in the DAKOTA software package are detailed herein. The principal contribution is a novel, effective, and efficient approach to handle ill-conditioning of GEK's %E2%80%9Ccorrelation%E2%80%9D matrix, RN%CC%83, based on a pivoted Cholesky factorization of Kriging's (not GEK's) correlation matrix, R, which is a small sub-matrix within GEK's RN%CC%83 matrix. The approach discards sample points/equations that contribute the least %E2%80%9Cnew%E2%80%9D information to RN%CC%83. Since these points contain the least new information, they are the ones which when discarded are both the easiest to predict and provide maximum improvement of RN%CC%83's conditioning. Prior to this work, handling ill-conditioned correlation matrices was a major, perhaps the principal, unsolved challenge necessary for robust and efficient GEK emulators. Numerical results demonstrate that GEK predictions can be significantly more accurate when GEK is allowed to discard points by the presented method. Numerical results also indicate that GEK can be used to break the curse of dimensionality by exploiting inexpensive derivatives (such as those provided by automatic differentiation or adjoint techniques), smoothness in the response being modeled, and adaptive sampling. Development of a suitable adaptive sampling algorithm was beyond the scope of this work; instead adaptive sampling was approximated by omitting the cost of samples discarded by the presented pivoted Cholesky approach.

Modelagem da polimerização simultânea de estireno em suspensão e emulsão Modeling styrene simultaneous suspension and emulsion polymerization systems

Directory of Open Access Journals (Sweden)

Marcelo K. Lenzi

2004-06-01

Full Text Available Apesar dos processos de polimerização em suspensão e emulsão serem processos heterogêneos, cada um origina características peculiares para a distribuição de tamanho de partículas, distribuição de pesos moleculares, taxa de nucleação das partículas de polímero, taxa de polimerização, entre outras. Neste trabalho, são realizadas polimerizações de estireno simultaneamente em suspensão e emulsão. A carga inicial do reator equivale à receita de uma polimerização em suspensão tradicional, enquanto os constituintes da emulsão são adicionados ao longo da batelada. Analisa-se como as propriedades finais do polímero e o curso da polimerização dependem do momento em que a carga característica da emulsão é adicionada à polimerização em suspensão. Apresenta-se, também, um modelo matemático para a descrição do sistema, sendo que o modelo proposto possui boa concordância com dados experimentais de conversão, pesos moleculares médios e curva de distribuição de pesos moleculares. A morfologia da partícula de polímero e os pesos moleculares médios mudam significativamente, dependendo do momento da adição da emulsão, podendo até mesmo ser obtidas curvas de distribuição de pesos moleculares bimodais. Verificou-se que as partículas apresentam características do tipo núcleo/casca, sendo o núcleo formado pelas partículas obtidas pela polimerização em suspensão e a casca formada pelas partículas do processo em emulsão.Although both emulsion and suspension polymerization processes are performed in heterogeneous media, each process presents its own typical characteristics, such as the particle size distribution, molecular weight distribution, polymer particle nucleation rates, rates of polymerization, and so on. In this work styrene polymerizations are carried out in suspension and emulsion processes simultaneously. The initial reactor charge resembles the recipe of standard styrene suspension

A new self-emulsifying formulation of mefenamic acid with enhanced drug dissolution

Directory of Open Access Journals (Sweden)

Pornsak Sriamornsak

2015-04-01

Full Text Available To enhance the dissolution of poorly soluble mefenamic acid, self-emulsifying formulation (SEF, composing of oil, surfactant and co-surfactant, was formulated. Among the oils and surfactants studied, Imwitor® 742, Tween® 60, Cremophore® EL and Transcutol® HP were selected as they showed maximal solubility to mefenamic acid. The ternary phase diagram was constructed to find optimal concentration that provided the highest drug loading. The droplet size after dispersion and drug dissolution of selected formulations were investigated. The results showed that the formulation containing Imwitor® 742, Tween® 60 and Transcutol® HP (10:30:60 can encapsulate high amount of mefenamic acid. The dissolution study demonstrated that, in the medium containing surfactant, nearly 100% of mefenamic acid were dissolved from SEF within 5 min while 80% of drugs were dissolved from the commercial product in 45 min. In phosphate buffer (without surfactant, 80% of drug were dissolved from the developed SEF within 5 min while only about 13% of drug were dissolved in 45 min, from the commercial product. The results suggested that the SEF can enhance the dissolution of poorly soluble drug and has a potential to enhance drug absorption and improve bioavailability of drug.

Placement of empty catheters for an HDR-emulating LDR prostate brachytherapy technique: comparison to standard intraoperative planning.

Science.gov (United States)

Niedermayr, Thomas R; Nguyen, Paul L; Murciano-Goroff, Yonina R; Kovtun, Konstantin A; Neubauer Sugar, Emily; Cail, Daniel W; O'Farrell, Desmond A; Hansen, Jorgen L; Cormack, Robert A; Buzurovic, Ivan; Wolfsberger, Luciant T; O'Leary, Michael P; Steele, Graeme S; Devlin, Philip M; Orio, Peter F

2014-01-01

We sought to determine whether placing empty catheters within the prostate and then inverse planning iodine-125 seed locations within those catheters (High Dose Rate-Emulating Low Dose Rate Prostate Brachytherapy [HELP] technique) would improve concordance between planned and achieved dosimetry compared with a standard intraoperative technique. We examined 30 consecutive low dose rate prostate cases performed by standard intraoperative technique of planning followed by needle placement/seed deposition and compared them to 30 consecutive low dose rate prostate cases performed by the HELP technique. The primary endpoint was concordance between planned percentage of the clinical target volume that receives at least 100% of the prescribed dose/dose that covers 90% of the volume of the clinical target volume (V100/D90) and the actual V100/D90 achieved at Postoperative Day 1. The HELP technique had superior concordance between the planned target dosimetry and what was actually achieved at Day 1 and Day 30. Specifically, target D90 at Day 1 was on average 33.7 Gy less than planned for the standard intraoperative technique but was only 10.5 Gy less than planned for the HELP technique (p 0.05). Placing empty needles first and optimizing the plan to the known positions of the needles resulted in improved concordance between the planned and the achieved dosimetry to the target, possibly because of elimination of errors in needle placement. Copyright © 2014 American Brachytherapy Society. Published by Elsevier Inc. All rights reserved.

Laboratory evaluation of the emulsifying characteristics of pumps. [Bilge and ballast water oily wastes

Energy Technology Data Exchange (ETDEWEB)

Harvey, A.C.; Guzdar, A.R.; Fiswell, D.R.

1973-10-01

The program was devoted to a laboratory investigation of the emulsifying characteristics of different pumps suitable for shipboard pumping of bilge and ballast water oily wastes. The tests were designed to investigate the effect of several parameters, such as oil type, input oil concentration, detergent, pump operating characteristics (pressure and flow rate), and salt versus fresh water, on emulsification. Tests were conducted on the Foster-Miller tests loop. No. 2 fuel oil, lubricating oil and No. 6 fuel oil were the oils tested at concentrations ranging from 1 to 10%. The oils were tested with and without the addition of 10% Gamlen D surfactant. The pumps used were a Parker Diaphragm pump, a Blackmer Sliding Vane pump, an Ingersoll Rand Centrifugal pump and a Deming Centrifugal pump. Pump pressure ranged from 10 to 60 psi and flow rate from 10 to 100 gpm. A total of 270 tests were conducted covering 198 different operating points, 108 concerning pump comparison, 54 concerning oil concentration and surfactant, and 45 concerning salt water.

Avaliação da eficiência do ultrassom no processo de separação de fases em água produzida e em emulsões sintéticas do tipo O/A

OpenAIRE

Ronchi, Renata Peterle

2014-01-01

Um grande problema das indústrias petrolíferas está relacionado ao desenvolvimento de tecnologias eficazes para o tratamento da água produzida proveniente da etapa de processamento primário, apresentando-se como emulsões estáveis do tipo óleo/água. Este estudo descreve uma metodologia de síntese de emulsões do tipo óleo em água, e aplica testes com ultrassom, para avaliar a capacidade desta técnica em propor uma separação de fases e consequente redução do Teor de Óleos e Gra...

Hardware-in-the-Loop emulator for a hydrokinetic turbine

Science.gov (United States)

Rat, C. L.; Prostean, O.; Filip, I.

2018-01-01

Hydroelectric power has proven to be an efficient and reliable form of renewable energy, but its impact on the environment has long been a source of concern. Hydrokinetic turbines are an emerging class of renewable energy technology designed for deployment in small rivers and streams with minimal environmental impact on the local ecosystem. Hydrokinetic technology represents a truly clean source of energy, having the potential to become a highly efficient method of harvesting renewable energy. However, in order to achieve this goal, extensive research is necessary. This paper presents a Hardware-in-the-Loop emulator for a run-of-the-river type hydrokinetic turbine. The HIL system uses an ABB ACS800 drive to control an induction machine as a significant means of replicating the behavior of the real turbine. The induction machine is coupled to a permanent magnet synchronous generator and the corresponding load. The ACS800 drive is controlled through the software system, which comprises of the hydrokinetic turbine real-time simulation through mathematical modeling in the LabVIEW programming environment running on a NI CompactRIO (cRIO) platform. The advantages of this method are that it can provide a means for testing many control configurations without requiring the presence of the real turbine. This paper contains the basic principles of a hydrokinetic turbine, particularly the run-of-the-river configurations along with the experimental results obtained from the HIL system.

Towards an acoustical platform for many-body spin emulation: Transmon qubits patterned on a piezoelectric material

Science.gov (United States)

Moores, Brad A.; Sletten, Lucas R.; Viennot, Jeremie; Lehnert, K. W.

Man-made systems of interacting qubits are a promising and powerful way of exploring many-body spin physics beyond classical computation. Although transmon qubits are perhaps the most advanced quantum computing technology, building a system of such qubits designed to emulate a system of many interacting spins is hindered by the mismatch of scales between the transmons and the electromagnetic modes that couple them. We propose a strategy to overcome this mismatch by using surface acoustic waves, which couple to qubits piezoelectrically and have micron wavelengths at GHz frequencies. In this talk, we will present characterizations of transmon qubits fabricated on a piezoelectric material, and show that their coherence properties are sufficient to explore acoustically mediated qubit interactions.

Emulation of neutron irradiation effects with protons: validation of principle

International Nuclear Information System (INIS)

Was, G.S.; Busby, J.T.; Allen, T.; Kenik, E.A.; Jensson, A.; Bruemmer, S.M.; Gan, J.; Edwards, A.D.; Scott, P.M.; Andreson, P.L.

2002-01-01

This paper presents the results of the irradiation, characterization and irradiation assisted stress corrosion cracking (IASCC) behavior of proton- and neutron-irradiated samples of 304SS and 316SS from the same heats. The objective of the study was to determine whether proton irradiation does indeed emulate the full range of effects of in-reactor neutron irradiation: radiation-induced segregation (RIS), irradiated microstructure, radiation hardening and IASCC susceptibility. The work focused on commercial heats of 304 stainless steel (heat B) and 316 stainless steel (heat P). Irradiation with protons was conducted at 360 deg. C to doses between 0.3 and 5.0 dpa to approximate those by neutron irradiation at 275 deg. C over the same dose range. Characterization consisted of grain boundary microchemistry, dislocation loop microstructure, hardness as well as stress corrosion cracking (SCC) susceptibility of both un-irradiated and irradiated samples in oxygenated and de-oxygenated water environments at 288 deg. C. Overall, microchemistry, microstructure, hardening and SCC behavior of proton- and neutron-irradiated samples were in excellent agreement. RIS analysis showed that in both heats and for both irradiating particles, the pre-existing grain boundary Cr enrichment transformed into a 'W' shaped profile at 1.0 dpa and then into a 'V' shaped profile between 3.0 and 5.0 dpa. Grain boundary segregation of Cr, Ni, Si, and Mo all followed the same trends and agreed well in magnitude. The microstructure of both proton- and neutron-irradiated samples was dominated by small, faulted dislocation loops. Loop size distributions were nearly identical in both heats over a range of doses. Saturated loop size following neutron irradiation was about 30% larger than that following proton irradiation. Loop density increased with dose through 5.0 dpa for both particle irradiations and was a factor of 3 greater in neutron-irradiated samples vs. proton-irradiated samples. Grain boundary

Effects of Carriers, Emulsifiers, and Biopesticides for Direct Silk Treatments on Caterpillar Feeding Damage and Ear Development in Sweet Corn.

Science.gov (United States)

Westgate, P J; Schultz, B B; Hazzard, R V

2017-04-01

In the northeastern United States, control of Lepidopteran pests of sweet corn, particularly corn earworm [Helicoverpa zea (Boddie)], is difficult using organic methods. The direct application of corn oil and Bacillus thuringiensis (Bt) to corn silk has been shown to reduce ear damage from corn earworm in past studies; these studies sought to optimize this method by evaluating additional carrier and biopesticide mixtures that comply with the United States Federal Insecticide, Fungicide, and Rodenticide Act and National Organic Standards. Carriers, which are liquids used to dissolve the biopesticide and deliver it into the tip of the ear, may have phytotoxic or insecticidal properties. Experiments conducted from 2001 to 2005 evaluated caterpillar damage and ear development effects from carriers (vegetable and paraffinic oils and carrageenan), biopesticides (Bt, spinsosad, and neem), and three emulsifiers in various combinations when applied directly to the tips of the ears 5-7 d after silk initiation. There were no effects of emulsifiers on ear quality, except for slight reduction in caterpillar damage in one of the two years. There were no differences among corn, soy, canola, and safflower oils in corn earworm control or tip development. The carrageenan carrier had the least effect upon ear development as measured by the length of nonpollinated kernels at the tip, compared to corn oil or paraffinic oil (JMS Stylet Oil), which caused the greatest tip damage as well as an oily discoloration. The carrier-pesticide combinations with the best ear quality overall were spinosad in carrageenan or corn oil, and Bt in carrageenan. © The Authors 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

On-line use of the 168/E emulator at the CERN ISR SFM detector

International Nuclear Information System (INIS)

Bertuzzi, C.; Drijard, D.; Frehse, H.; Gavillet, P.; Gokieli, R.; Innocenti, P.G.; Messerli, R.; Mornacchi, G.; Norton, A.; Porte, J.P.

1981-01-01

The Split Field Magnet Detector at the CERN ISR has been used in recent years to study events with a high transverse momentum charged particle. As a first level computer based trigger a linear estimate of the track momentum by fixed point arithmethic was calculated on-line by a minicomputer. In addition appreciable further rejection was obtained by off-line filtering on the IBM-370/168, using pattern recognition and a fit of the triggering particle in the magnetic field. The availability of the 168/E emulator makes it possible to transfer the proven methods used off-line to real time data reduction. Preliminary results on filter efficiency and speed for an experiment triggering on a high Psub(T) hadron at 10 to 20 0 with respect to the outgoing beam (Exp. R 419) are given. Possible improvements and extensions are discussed. (orig.)

Critical Clearing Time and Wind Power in Small Isolated Power Systems Considering Inertia Emulation

Directory of Open Access Journals (Sweden)

Elías Jesús Medina-Domínguez

2015-11-01

Full Text Available The stability and security of small and isolated power systems can be compromised when large amounts of wind power enter them. Wind power integration depends on such factors as power generation capacity, conventional generation technology or grid topology. Another issue that can be considered is critical clearing time (CCT. In this paper, wind power and CCT are studied in a small isolated power system. Two types of wind turbines are considered: a squirrel cage induction generator (SCIG and a full converter. Moreover, the full converter wind turbine’s inertia emulation capability is considered, and its impact on CCT is discussed. Voltage is taken into account because of its importance in power systems of this kind. The study focuses on the small, isolated Lanzarote-Fuerteventura power system, which is expected to be in operation by 2020.

Effect of monomer concentration on the kinetics of emulsifier-free emulsion polymerization of Vinyl Acetate and Methyl Acrylate

International Nuclear Information System (INIS)

Mohammad Beigi, H. R.

2001-01-01

The effect of monomer concentration on the kinetics of the emulsifier-free emulsion polymerization of vinyl acetate and methyl acrylate were studied. The polymerizations were carried out using potassium persulfate as the initiator. Form the electron micrographs of the resulting lattices, monodisperse PVAc and PMA lattices with particle diameters varying between 149-443 mm and 112-497 nm, respectively were processed. Uniformity of particle size indicated that nucleation of stable particle occurs early in the polymerization process. The polymerization rate was found to be proportional to the 0.88 and 1.5 power of the initial monomer concentration of vinyl acetate and methyl acrylate, respectively. Higher monomer concentration results in fewer particles and larger final particle diameter. With increasing monomer solubility in water the size of particle decreases and its distribution broadens

New functionalities of Maillard reaction products as emulsifiers and encapsulating agents, and the processing parameters: a brief review.

Science.gov (United States)

Lee, Yee-Ying; Tang, Teck-Kim; Phuah, Eng-Tong; Alitheen, Noorjahan Banu Mohamed; Tan, Chin-Ping; Lai, Oi-Ming

2017-03-01

Non-enzymatic browning has been a wide and interesting research area in the food industry, ranging from the complexity of the reaction to its applications in the food industry as well as its ever-debatable health effects. This review provides a new perspective to the Maillard reaction apart from its ubiquitous function in enhancing food flavour, taste and appearance. It focuses on the recent application of Maillard reaction products as an inexpensive and excellent source of emulsifiers as well as superior encapsulating matrices for the entrapment of bioactive compounds. Additionally, it will also discuss the latest approaches employed to perform the Maillard reaction as well as several important reaction parameters that need to be taken into consideration when conducting the Maillard reaction. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Emulation-based comparative study of centralized and distributed control schemes for optical networks

Science.gov (United States)

Xin, Chunsheng; Ye, Yinghua; Dixit, Sudhir; Qiao, Chunming

2001-07-01

Recently there are considerable amount of research about the automatic control and provisioning in all optical networks. One of the critical issues is how to provide effective lightpath provisioning to improve network performance, such as blocking probability and decision time. Depending on the network topology, configuration, and administration policy, a distributed or centralized control scheme can be employed to manage the routing and signaling. In a distributed control scheme, each node exchanges information with other nodes, but performs routing and signaling independently from other nodes. On the other hand, in a centralized scheme, each node communicates with a central controller and the controller performs routing and signaling on behalf of all other nodes. Intuitively, the centralized scheme can obtain a lower blocking probability since the controller has the complete resource availability information. We have studied the two schemes through emulations, determined the signaling and processing overheads and quantified the conditions that favor one approach over the other.

Using RBF to Enable Circuit Emulation Service over Internet%采用RBF来支撑互联网络上的电路模拟服务

Institute of Scientific and Technical Information of China (English)

金涬; 张斌; 赵阳; 王庆波; 陈滢

2009-01-01

Circuit Emulation Service(CES)aims to enable packet switched networks to provide guaranteed services with comparable qualities of circuit switched networks.Our paper addresses the key issue of QoS of CES flows over Internet.Enlightened by the time division idea popularly used in circuit switched networks,we propose a time division based control mechanism to provide guaranteed QoS for the constant-rate CES flows.The control mechanism is able to estimate the arrival times of the coming packets in CES flows,and reserve the time slots for them.ACCOrdingly.it enables the packets to consume the reserved time slots of their own,so the CES flows are guaranteed to be processed.Refreshing Bloom Filter(RBF),an efficient data representation structure,is proposed to support the time division control mechanism.It consists of multiple bloom filters,and can efficiently record the arrival time slots of millions of packets.The proposed control system model could be a practical tool to support Circuit Emulation Services over Intemet.

The influence of animal fat replacement with vegetable oils on sensorial perception of meat emulsified products

Directory of Open Access Journals (Sweden)

Cristian TUDOSE

2014-12-01

Full Text Available For the purpose of the present study, in an emulsified meat product the pork backfat was replaced with a vegetable oil pre-emulsion and its effect on quality attributes were investigated. In order to do so, a classic and a new meat products were manufactured. Extra virgin olive oil and palm oil pre-emulsion were added instead of animal fat in the new product. Texture and physiochemical properties were analyzed by instrumental measurements. It was observed that during storage moisture and pH decreased. Using vegetable oils determined substantial increase of TBA values. Texture was influenced mainly by storage time for both products, while replacement of pork backfat with vegetable oil pre-emulsion had no influence on sample firmness. The sensory properties of meat products were evaluated by a group of trained panelists using an analitycal sensory evaluation technique. Overall the new product presented good acceptability which recommends it like a new healthier meat product.

The Physical State of Emulsified Edible Oil Modulates Its in Vitro Digestion.

Science.gov (United States)

Guo, Qing; Bellissimo, Nick; Rousseau, Dérick

2017-10-18

Emulsified lipid digestion was tailored by manipulating the physical state of dispersed oil droplets in whey protein stabilized oil-in-water (O/W) emulsions, where the oil phase consisted of one of five ratios of soybean oil (SO) and fully hydrogenated soybean oil (FHSO). The evolution in particle size distribution, structural changes during oral, gastric, and intestinal digestion, and free fatty acid release during intestinal digestion were all investigated. Irrespective of the physical state and structure of the dispersed oil/fat, all emulsions were stable against droplet size increases during oral digestion. During gastric digestion, the 50:50 SO:FHSO emulsion was more stable against physical breakdown than any other emulsion. All emulsions underwent flocculation and coalescence or partial coalescence upon intestinal digestion, with the SO emulsion being hydrolyzed the most rapidly. The melting point of all emulsions containing FHSO was above 37 °C, with the presence of solid fat within the dispersed oil droplets greatly limiting lipolysis. Fat crystal polymorph and nanoplatelet size did not play an important role in the rate and extent of lipid digestion. Free fatty acid release modeled by the Weibull distribution function showed that the rate of lipid digestion (κ) decreased with increasing solid fat content, and followed an exponential relationship (R 2 = 0.95). Overall, lipid digestion was heavily altered by the physical state of the dispersed oil phase within O/W emulsions.

Formulation, optimization, and evaluation of self-emulsifying drug delivery systems of nevirapine.

Science.gov (United States)

Chintalapudi, Ramprasad; Murthy, T E G K; Lakshmi, K Rajya; Manohar, G Ganesh

2015-01-01

The aim of the present study was to formulate and optimize the self-emulsifying drug delivery systems (SEDDS) of nevirapine (NVP) by use of 2(2) factorial designs to enhance the oral absorption of NVP by improving its solubility, dissolution rate, and diffusion profile. SEDDS are the isotropic mixtures of oil, surfactant, co-surfactant and drug that form oil in water microemulsion when introduced into the aqueous phase under gentle agitation. Solubility of NVP in different oils, surfactants, and co-surfactants was determined for the screening of excipients. Pseudo-ternary phase diagrams were constructed by the aqueous titration method, and formulations were developed based on the optimum excipient combinations with the help of data obtained through the maximum micro emulsion region containing combinations of oil, surfactant, and co-surfactant. The formulations of SEDDS were optimized by 2(2) factorial designs. The optimum formulation of SEDDS contains 32.5% oleic acid, 44.16% tween 20, and 11.9% polyethylene glycol 600 as oil, surfactant, and co-surfactant respectively. The SEDDS was evaluated for the following drug content, self-emulsification time, rheological properties, zeta potential, in vitro diffusion studies, thermodynamic stability studies, and in vitro dissolution studies. An increase in dissolution was achieved by SEDDS compared to pure form of NVP. Overall, this study suggests that the dissolution and oral bioavailability of NVP could be improved by SEDDS technology.

High speed fault tolerant secure communication for muon chamber using FPGA based GBTx emulator

Science.gov (United States)

Sau, Suman; Mandal, Swagata; Saini, Jogender; Chakrabarti, Amlan; Chattopadhyay, Subhasis

2015-12-01

The Compressed Baryonic Matter (CBM) experiment is a part of the Facility for Antiproton and Ion Research (FAIR) in Darmstadt at the GSI. The CBM experiment will investigate the highly compressed nuclear matter using nucleus-nucleus collisions. This experiment will examine lieavy-ion collisions in fixed target geometry and will be able to measure hadrons, electrons and muons. CBM requires precise time synchronization, compact hardware, radiation tolerance, self-triggered front-end electronics, efficient data aggregation schemes and capability to handle high data rate (up to several TB/s). As a part of the implementation of read out chain of Muon Cliamber(MUCH) [1] in India, we have tried to implement FPGA based emulator of GBTx in India. GBTx is a radiation tolerant ASIC that can be used to implement multipurpose high speed bidirectional optical links for high-energy physics (HEP) experiments and is developed by CERN. GBTx will be used in highly irradiated area and more prone to be affected by multi bit error. To mitigate this effect instead of single bit error correcting RS code we have used two bit error correcting (15, 7) BCH code. It will increase the redundancy which in turn increases the reliability of the coded data. So the coded data will be less prone to be affected by noise due to radiation. The data will go from detector to PC through multiple nodes through the communication channel. The computing resources are connected to a network which can be accessed by authorized person to prevent unauthorized data access which might happen by compromising the network security. Thus data encryption is essential. In order to make the data communication secure, advanced encryption standard [2] (AES - a symmetric key cryptography) and RSA [3], [4] (asymmetric key cryptography) are used after the channel coding. We have implemented GBTx emulator on two Xilinx Kintex-7 boards (KC705). One will act as transmitter and other will act as receiver and they are connected

High speed fault tolerant secure communication for muon chamber using FPGA based GBTx emulator

International Nuclear Information System (INIS)

Sau, Suman; Chakrabarti, Amlan; Saini, Jogender; Chattopadhyay, Subhasis; Mandal, Swagata

2015-01-01

The Compressed Baryonic Matter (CBM) experiment is a part of the Facility for Antiproton and Ion Research (FAIR) in Darmstadt at the GSI. The CBM experiment will investigate the highly compressed nuclear matter using nucleus-nucleus collisions. This experiment will examine lieavy-ion collisions in fixed target geometry and will be able to measure hadrons, electrons and muons. CBM requires precise time synchronization, compact hardware, radiation tolerance, self-triggered front-end electronics, efficient data aggregation schemes and capability to handle high data rate (up to several TB/s). As a part of the implementation of read out chain of Muon Cliamber(MUCH) [1] in India, we have tried to implement FPGA based emulator of GBTx in India. GBTx is a radiation tolerant ASIC that can be used to implement multipurpose high speed bidirectional optical links for high-energy physics (HEP) experiments and is developed by CERN. GBTx will be used in highly irradiated area and more prone to be affected by multi bit error. To mitigate this effect instead of single bit error correcting RS code we have used two bit error correcting (15, 7) BCH code. It will increase the redundancy which in turn increases the reliability of the coded data. So the coded data will be less prone to be affected by noise due to radiation. The data will go from detector to PC through multiple nodes through the communication channel. The computing resources are connected to a network which can be accessed by authorized person to prevent unauthorized data access which might happen by compromising the network security. Thus data encryption is essential. In order to make the data communication secure, advanced encryption standard [2] (AES - a symmetric key cryptography) and RSA [3], [4] (asymmetric key cryptography) are used after the channel coding. We have implemented GBTx emulator on two Xilinx Kintex-7 boards (KC705). One will act as transmitter and other will act as receiver and they are connected

Influence of emulsifiers on the optimization of processing parameters of refining milk chocolate in the ball mill

Directory of Open Access Journals (Sweden)

Pajin Biljana

2011-01-01

Full Text Available Chocolate manufacture is a complex process which includes a large number of technology operations. One of the obligatory phases is milling, called refining, which aims at obtaining the appropriate distribution of particle size, resulting in the chocolate with optimal physical and sensory characteristics. The aim of this work was to define and optimize the process parameters for the production of milk chocolate by a non-conventional procedure, using the ball mill. The quality of chocolate mass, produced on this way, is determined by measuring the following parameters: moisture, size of the largest cocoa particle, yield flow, and Casson plastic viscosity. A special consideration of this study is the optimization of the types and amounts of emulsifiers, which are responsible for achieving the appropriate rheological and physical characteristics of the chocolate mass. The obtained parameters are compared with those which are typical for the standard procedure.

Mechanistic site-based emulation of a global ocean biogeochemical model (MEDUSA 1.0 for parametric analysis and calibration: an application of the Marine Model Optimization Testbed (MarMOT 1.1

Directory of Open Access Journals (Sweden)

J. C. P. Hemmings

2015-03-01

Full Text Available Biogeochemical ocean circulation models used to investigate the role of plankton ecosystems in global change rely on adjustable parameters to capture the dominant biogeochemical dynamics of a complex biological system. In principle, optimal parameter values can be estimated by fitting models to observational data, including satellite ocean colour products such as chlorophyll that achieve good spatial and temporal coverage of the surface ocean. However, comprehensive parametric analyses require large ensemble experiments that are computationally infeasible with global 3-D simulations. Site-based simulations provide an efficient alternative but can only be used to make reliable inferences about global model performance if robust quantitative descriptions of their relationships with the corresponding 3-D simulations can be established. The feasibility of establishing such a relationship is investigated for an intermediate complexity biogeochemistry model (MEDUSA coupled with a widely used global ocean model (NEMO. A site-based mechanistic emulator is constructed for surface chlorophyll output from this target model as a function of model parameters. The emulator comprises an array of 1-D simulators and a statistical quantification of the uncertainty in their predictions. The unknown parameter-dependent biogeochemical environment, in terms of initial tracer concentrations and lateral flux information required by the simulators, is a significant source of uncertainty. It is approximated by a mean environment derived from a small ensemble of 3-D simulations representing variability of the target model behaviour over the parameter space of interest. The performance of two alternative uncertainty quantification schemes is examined: a direct method based on comparisons between simulator output and a sample of known target model "truths" and an indirect method that is only partially reliant on knowledge of the target model output. In general, chlorophyll

Emulsifying and gelling properties of weakfish myofibrillar proteins as affected by squid mantle myofibrillar proteins in a model system

Directory of Open Access Journals (Sweden)

Daniela Mariel Suarez

2014-03-01

Full Text Available The aim of the present work was to investigate the physicochemical, biochemical and functional characteristics of both the myofibrils (MF and actomyosin (AM of squid mantle (Illex argentinus and weakfish (Cynoscion guatucupa muscles, and evaluate the influence of the addition of myofibrilar proteins from the squid mantle on the physicochemical and functional properties of those of the weakfish. After extraction, purification and characterization of the MF and AM of both species, emulsions of each protein fraction from each muscle were formulated. Mixtures of the MF or AM of both species were also analyzed. The emulsifying properties were monitoring using the Emulsifying Activity Index (EAI and Emulsion Stability (ES. In addition, gel pastes were formulated from the squid mantle, weakfish muscle and the mixture of both species, and the following functional properties of the gels assessed: water holding capacity, colour, textural profile analysis (TPA (hardness, elasticity, cohesiveness, gumminess and gel strength. The EAI values of emulsions formulated with the MF of the mantle were significantly (p<0.05 higher than those formulated from those of weakfish. The incorporation of squid MF in the mixture increased the EAI values. Conversely, the highest ES values were obtained with weakfish MF, and the incorporation of MF weakfish in the mixture increased the ES values. Similar EAI and ES behaviours were observed for the AM of the corresponding species. Irrespective of the thermal treatment, the gel strength of the gelled paste of squid muscle was significantly (p<0.05 lower than that of weakfish muscle and of those obtained with the different mixtures. The behaviours of the expressible moisture (EM from the gelled pastes were similar to those of gel strength. Irrespective of the thermal treatment, the pastes formulated with a high weakfish: mantle ratio showed less water loss. The gelled pastes of squid mantle showed the highest values for whiteness

Bayesian uncertainty analysis for complex systems biology models: emulation, global parameter searches and evaluation of gene functions.

Science.gov (United States)

Vernon, Ian; Liu, Junli; Goldstein, Michael; Rowe, James; Topping, Jen; Lindsey, Keith

2018-01-02

Many mathematical models have now been employed across every area of systems biology. These models increasingly involve large numbers of unknown parameters, have complex structure which can result in substantial evaluation time relative to the needs of the analysis, and need to be compared to observed data of various forms. The correct analysis of such models usually requires a global parameter search, over a high dimensional parameter space, that incorporates and respects the most important sources of uncertainty. This can be an extremely difficult task, but it is essential for any meaningful inference or prediction to be made about any biological system. It hence represents a fundamental challenge for the whole of systems biology. Bayesian statistical methodology for the uncertainty analysis of complex models is introduced, which is designed to address the high dimensional global parameter search problem. Bayesian emulators that mimic the systems biology model but which are extremely fast to evaluate are embeded within an iterative history match: an efficient method to search high dimensional spaces within a more formal statistical setting, while incorporating major sources of uncertainty. The approach is demonstrated via application to a model of hormonal crosstalk in Arabidopsis root development, which has 32 rate parameters, for which we identify the sets of rate parameter values that lead to acceptable matches between model output and observed trend data. The multiple insights into the model's structure that this analysis provides are discussed. The methodology is applied to a second related model, and the biological consequences of the resulting comparison, including the evaluation of gene functions, are described. Bayesian uncertainty analysis for complex models using both emulators and history matching is shown to be a powerful technique that can greatly aid the study of a large class of systems biology models. It both provides insight into model behaviour

Development of Quantitative Structure-Property Relationship Models for Self-Emulsifying Drug Delivery System of 2-Aryl Propionic Acid NSAIDs

Directory of Open Access Journals (Sweden)

Chen-Wen Li

2011-01-01

Full Text Available We developed the quantative structure-property relationships (QSPRs models to correlate the molecular structures of surfactant, cosurfactant, oil, and drug with the solubility of poorly water-soluble 2-aryl propionic acid nonsteroidal anti-inflammatory drugs (2-APA-NSAIDs in self-emulsifying drug delivery systems (SEDDSs. The compositions were encoded with electronic, geometrical, topological, and quantum chemical descriptors. To obtain reliable predictions, we used multiple linear regression (MLR and artificial neural network (ANN methods for model development. The obtained equations were validated using a test set of 42 formulations and showed a great predictive power, and linear models were found to be better than nonlinear ones. The obtained QSPR models would greatly facilitate fast screening for the optimal formulations of SEDDS at the early stage of drug development and minimize experimental effort.

ESSE: Engineering Super Simulation Emulation for Virtual Reality Systems Environment

International Nuclear Information System (INIS)

Suh, Kune Y.; Yeon, Choul W.

2008-01-01

The trademark 4 + D Technology TM based Engineering Super Simulation Emulation (ESSE) is introduced. ESSE resorting to three-dimensional (3D) Virtual Reality (VR) technology pledges to provide with an interactive real-time motion, sound and tactile and other forms of feedback in the man machine systems environment. In particular, the 3D Virtual Engineering Neo cybernetic Unit Soft Power (VENUS) adds a physics engine to the VR platform so as to materialize a physical atmosphere. A close cooperation system and prompt information share are crucial, thereby increasing the necessity of centralized information system and electronic cooperation system. VENUS is further deemed to contribute towards public acceptance of nuclear power in general, and safety in particular. For instance, visualization of nuclear systems can familiarize the public in answering their questions and alleviating misunderstandings on nuclear power plants answering their questions and alleviating misunderstandings on nuclear power plants (NPPs) in general, and performance, security and safety in particular. An in-house flagship project Systemic Three-dimensional Engine Platform Prototype Engineering (STEPPE) endeavors to develop the Systemic Three-dimensional Engine Platform (STEP) for a variety of VR applications. STEP is home to a level system providing the whole visible scene of virtual engineering of man machine system environment. The system is linked with video monitoring that provides a 3D Computer Graphics (CG) visualization of major events. The database linked system provides easy access to relevant blueprints. The character system enables the operators easy access to visualization of major events. The database linked system provides easy access to relevant blueprints. The character system enables the operators to access the virtual systems by using their virtual characters. Virtually Engineered NPP Informative systems by using their virtual characters. Virtually Engineered NPP Informative

Synesthesia, sensory-motor contingency, and semantic emulation: how swimming style-color synesthesia challenges the traditional view of synesthesia.

Science.gov (United States)

Mroczko-Wąsowicz, Aleksandra; Werning, Markus

2012-01-01

Synesthesia is traditionally regarded as a phenomenon in which an additional non-standard phenomenal experience occurs consistently in response to ordinary stimulation applied to the same or another modality. Recent studies suggest an important role of semantic representations in the induction of synesthesia. In the present proposal we try to link the empirically grounded theory of sensory-motor contingency and mirror system based embodied simulation/emulation to newly discovered cases of swimming style-color synesthesia. In the latter color experiences are evoked only by showing the synesthetes a picture of a swimming person or asking them to think about a given swimming style. Neural mechanisms of mirror systems seem to be involved here. It has been shown that for mirror-sensory synesthesia, such as mirror-touch or mirror-pain synesthesia (when visually presented tactile or noxious stimulation of others results in the projection of the tactile or pain experience onto oneself), concurrent experiences are caused by overactivity in the mirror neuron system responding to the specific observation. The comparison of different forms of synesthesia has the potential of challenging conventional thinking on this phenomenon and providing a more general, sensory-motor account of synesthesia encompassing cases driven by semantic or emulational rather than pure sensory or motor representations. Such an interpretation could include top-down associations, questioning the explanation in terms of hard-wired structural connectivity. In the paper the hypothesis is developed that the wide-ranging phenomenon of synesthesia might result from a process of hyperbinding between "too many" semantic attribute domains. This hypothesis is supplemented by some suggestions for an underlying neural mechanism.

Preparation of Fe3O4/poly(styrene-butyl acrylate-[2-(methacryloxy)ethyl]trimethylammonium chloride) by emulsifier-free emulsion polymerization and its interaction with DNA

International Nuclear Information System (INIS)

Li Xiaolong; Liu Guoqiang; Yan Wei; Chu, Paul K.; Yeung, Kelvin W.K.; Wu Shuilin; Yi Changfeng; Xu Zushun

2012-01-01

Cationic magnetic polymer particles Fe 3 O 4 /poly(styrene-butyl acrylate-[2-(methacryloxy)ethyl]trimethylammonium chloride), a type of potential gene carrier, were prepared by emulsifier-free emulsion polymerization with oleic acid modified magnetite Fe 3 O 4 , styrene, butyl acrylate and [2-(methacryloxy)ethyl]trimethylammonium chloride) (METAC). The morphology of the particles was characterized by transmission electron microscopy and the composites of particles were characterized by FT-IR spectroscopy, X-ray diffraction. These results showed that magnetic particles were well dispersed in polymers with the content of about 15%(wt/wt). The composites exhibited superparamagnetism and possessed a certain level of magnetic response. The interactions between the particles with calf-thymus DNA (ct DNA) were confirmed by zeta potential measurement, UV–vis spectroscopy and fluorescence spectroscopy. The DNA-binding capacity determined by the agarose gel electrophoresis showed good binding capacity of the emulsion to DNA. These results suggested the potential of the cationic magnetic polymer emulsion as gene target delivery carrier. - Highlights: ► A new type of cationic magnetic polymer particles was synthesized by emulsifier-free emulsion polymerization. ► Structural, morphological, and magnetic properties of the composite were evaluated. ► The interaction between cationic magnetic polymer particles with DNA was confirmed by zeta potential measurements. ► UV–vis spectrophotometry, fluorescent spectroscopy and agarose gel electrophoresis. ► This process may have potential applications to gene carrier and DNA separation.

Efeito da hidrólise tríptica e do pH sobre as propriedades funcionais do plasma bovino The effect of the tryptic hydrolysis and the pH on the functional properties of bovine plasma

Directory of Open Access Journals (Sweden)

Cléia Batista Dias Ornellas

2003-04-01

Full Text Available Visando a utilização do plasma bovino como agente funcional de alimentos, foram estudadas, na faixa de pH de 3,0 a 8,0, a solubilidade, a hidrofobicidade e a sua habilidade de formar e estabilizar emulsões. Para tal, foram determinados a capacidade emulsionante (EC, o índice de atividade emulsionante (EAI e a estabilidade da emulsão (ES. O efeito da ação da tripsina sobre estas propriedades foi, também, verificado, tendo sido preparados cinco hidrolisados enzimáticos. Os resultados obtidos indicam que a hidrofobicidade e o EAI apresentaram um máximo em pH 3,0 e 7,0, respectivamente, enquanto que as outras propriedades praticamente não foram influenciadas pela variação de pH. A hidrólise tríptica provocou uma redução da solubilidade e da EC, não afetou o EAI e a ES, tendo contribuído para melhorar apenas a hidrofobicidade, em alguns tempos de reação.Aiming to use of the bovine plasma as functional agent of foods, we studied its solubility, hidrophobicity and ability to form and to stabilize emulsions, in the range of pH from 3.0 to 8.0. Emulsifying capacity (EC, the emulsifying activity index (EAI and the stability of the emulsion (ES were determinated. The effect of the trypsin on these properties was also studied and five enzymatic hydrolysates were prepared. The results showed that hydrophobicity and EAI presented a maximum value at pH 3.0 and 7.0, respectively, while the other properties practically were not influenced by the pH variation. The tryptic hydrolysis produced a reduction of the solubility and EC, it showed no effect on EAI and ES and improved only the hidrophobicity in some periods of reaction.

Synthesis and emulsifying properties of carbohydrate fatty acid esters produced from Agave tequilana fructans by enzymatic acylation.

Science.gov (United States)

Casas-Godoy, Leticia; Arrizon, Javier; Arrieta-Baez, Daniel; Plou, Francisco J; Sandoval, Georgina

2016-08-01

Carbohydrate fatty acid esters are non-ionic surfactants with a broad spectrum of applications. These molecules are generally synthesized using short carbohydrates or linear fructans; however in this research carbohydrate fatty acid esters were produced for the first time with branched fructans from Agave tequilana. Using immobilized lipases we successfully acylated A. tequilana fructans with vinyl laurate, obtaining products with different degrees of polymerization (DP). Lipozyme 435 was the most efficient lipase to catalyze the transesterification reaction. HPLC and ESI-MS analysis proved the presence of a mixture of acylated products as a result of the chemical complexity of fructans in the A. tequilana. The ESI-MS spectra showed a molecular mass shift between 183 and 366g/mol for fructooligosaccharides with a DP lower than 6, which indicated the presence of Agave fructans that had been mono- and diacylated with lauric acid. The carbohydrate fatty acid esters (CFAE) obtained showed good emulsifying properties in W/O emulsions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Physical, Rheological, Functional, and Film Properties of a Novel Emulsifier: Frost Grape Polysaccharide from Vitis riparia Michx.

Science.gov (United States)

Hay, William T; Vaughn, Steven F; Byars, Jeffrey A; Selling, Gordon W; Holthaus, Derek M; Price, Neil P J

2017-10-04

A novel emulsifier, Frost grape polysaccharide (FGP), isolated from natural exudate of the species Vitis riparia Michx, was physically and rheologically characterized. The determination of the physical, structural, thermodynamic, emulsification, film, and rheological properties of FGP provide essential details for the commercial adoption of this novel plant polysaccharide. FGP is capable of producing exceptionally stable emulsions when compared with the industrially ubiquitous gum arabic (GA). The FGP isolate contained a negligible amount of nitrogen (0.03%), indicating that it does not contain an associated glycoprotein, unlike GA. Solutions of FGP have a high degree of thermostability, displaying no loss in viscosity with temperature cycling and no thermal degradation when held at 90 °C. FGP is an excellent film former, producing high tensile strength films which remain intact at temperatures up to 200 °C. This work identified a number of potential food and pharmaceutical applications where FGP is significantly superior to GA.

History matching of a complex epidemiological model of human immunodeficiency virus transmission by using variance emulation.

Science.gov (United States)

Andrianakis, I; Vernon, I; McCreesh, N; McKinley, T J; Oakley, J E; Nsubuga, R N; Goldstein, M; White, R G

2017-08-01

Complex stochastic models are commonplace in epidemiology, but their utility depends on their calibration to empirical data. History matching is a (pre)calibration method that has been applied successfully to complex deterministic models. In this work, we adapt history matching to stochastic models, by emulating the variance in the model outputs, and therefore accounting for its dependence on the model's input values. The method proposed is applied to a real complex epidemiological model of human immunodeficiency virus in Uganda with 22 inputs and 18 outputs, and is found to increase the efficiency of history matching, requiring 70% of the time and 43% fewer simulator evaluations compared with a previous variant of the method. The insight gained into the structure of the human immunodeficiency virus model, and the constraints placed on it, are then discussed.

MIMO Fading Emulator Development with FPGA and Its Application to Performance Evaluation of Mobile Radio Systems

Directory of Open Access Journals (Sweden)

Yoshio Karasawa

2017-01-01

Full Text Available We present four new developments for a multiple-input multiple-output (MIMO over-the-air measurement system based on our previous studies. The first two developments relate to the channel model for multipath environment generation. One is a further simplification of the circuit configuration without performance degradation by reducing the number of delay generation units, which dominate the performance limit when implementing the circuit on a field-programmable gate array (FPGA. The other is to realize spatial correlation characteristics among the input ports on the transmission side, whereas the previously proposed channel model did not consider this correlation. The third development involves the details of implementing the MIMO fading emulator on an FPGA as a two-stage scheme. The fourth is the demonstration of application examples of the developed system.

Characterization of edible emulsified films with low affinity to water based on kefiran and oleic acid.

Science.gov (United States)

Ghasemlou, Mehran; Khodaiyan, Faramarz; Oromiehie, Abdulrasoul; Yarmand, Mohammad Saeid

2011-10-01

New edible composite films based on kefiran and oleic acid (OA) at the ratio of 15, 25, and 35% (w/w) were prepared using emulsification with the aim of improving their water vapour barrier and mechanical properties. Film-forming solutions were characterized in terms of rheological properties and particle-size distribution. The impact of the incorporation of OA into the film matrix was studied by investigating the physical, mechanical, and thermal properties of the films. The water vapour permeability (WVP) of the emulsified films was reduced by approximately 33% by adding OA. The mechanical properties of kefiran films were also affected by adding OA: tensile strength was diminished, and elongation increased considerably. Differential scanning calorimetry showed that the glass transition temperature (T(g)) of the kefiran film was -16°C and was not considerably affected by adding OA. Therefore, OA could be incorporated into these films for some food-technology applications that need a low affinity toward water. Copyright © 2011 Elsevier B.V. All rights reserved.

Impact of Emulsifiers Addition on the Retrogradation of Rice Gels during Low-Temperature Storage

Directory of Open Access Journals (Sweden)

Zhe Yang

2017-01-01

Full Text Available Rice and its products are widely consumed in Asian countries; however, starch retrogradation decreases the quality and shortens the shelf-life of rice foods particularly at low temperature. In this study sucrose ester (SE, glycerol monostearate (GMS, and sodium stearoyl lactylate (SSL were added to rice flour and corresponding rice gels. Then, gelatinization properties, retrogradation characteristics, texture, and water content of these rice gels were investigated at 4°C and −20°C storage, respectively. The results demonstrated that the rice gels with 0.2% GMS had the lowest retrogradation index (ΔHr/ΔHg (11.84% and hardness (1359 g at 4°C for a 10 d period, which was significantly lower in comparison to control and the other two emulsifiers (P<0.05. Adhesiveness and water content were increased compared to the other samples. Furthermore, the retrogradation of rice gels stored at 4°C was comparatively rapid compared to gels stored at −20°C. Gel samples stored at −20°C were still acceptable for more than 15 days. Thus it was revealed that GMS has the potential to retard starch retrogradation and produce high-quality rice products in preservation.

Biomimetic Multilayer Nanofibrous Membranes with Elaborated Superwettability for Effective Purification of Emulsified Oily Wastewater.

Science.gov (United States)

Ge, Jianlong; Jin, Qing; Zong, Dingding; Yu, Jianyong; Ding, Bin

2018-05-09

Creating a porous membrane to effectively separate the emulsified oil-in-water emulsions with energy-saving property is highly desired but remains a challenge. Herein, a multilayer nanofibrous membrane was developed with the inspiration of the natural architectures of earth for gravity-driven water purification. As a result, the obtained biomimetic multilayer nanofibrous membranes exhibited three individual layers with designed functions; they were the inorganic nanofibrous layer to block the serious intrusion of oil to prevent the destructive fouling of the polymeric matrix; the submicron porous layer with designed honeycomb-like cavities to catch the smaller oil droplets and ensures a satisfactory water permeability; and the high porous fibrous substrate with larger pore size provided a template support and allows water to pass through quickly. Consequently, with the cooperation of these three functional layers, the resultant composite membrane possessed superior anti-oil-fouling property and robust oil-in-water emulsion separation performance with good separation efficiency and competitive permeation flux solely under the drive of gravity. The permeation flux of the membrane for the emulsion was up to 5163 L m -2 h -1 with a separation efficiency of 99.5%. We anticipate that our strategy could provide a facile route for developing a new generation of specific membranes for oily wastewater remediation.

Ravuconazole self-emulsifying delivery system: in vitro activity against Trypanosoma cruzi amastigotes and in vivo toxicity

Directory of Open Access Journals (Sweden)

Spósito PA

2017-05-01

Full Text Available Pollyanna Álvaro Spósito,1 Ana Lia Mazzeti,1,2 Caroline de Oliveira Faria,1 Julio A Urbina,3 Gwenaelle Pound-Lana,1 Maria Terezinha Bahia,2 Vanessa Furtado Mosqueira1 1Laboratory of Pharmaceutics and Nanotechnology Research, Pharmacy Department, School of Pharmacy, Universidade Federal de Ouro Preto, Minas Gerais, Brazil; 2Parasite Diseases Research Laboratory, NUPEB, Medical School, Universidade Federal de Ouro Preto, MG, Brazil; 3Venezuelan Institute for Scientific Research, Apartado, Caracas, Venezuela Abstract: Self-emulsifying drug delivery systems (SEDDSs are lipid-based anhydrous formulations composed of an isotropic mixture of oil, surfactant, and cosurfactants usually presented in gelatin capsules. Ravuconazole (Biopharmaceutics Classification System [BCS] Class II is a poorly water-soluble drug, and a SEDDS type IIIA was designed to deliver it in a predissolved state, improving dissolution in gastrointestinal fluids. After emulsification, the droplets had mean hydrodynamic diameters <250 nm, zeta potential values in the range of −45 mV to −57 mV, and showed no signs of ravuconazole precipitation. Asymmetric flow field-flow fractionation with dynamic and multiangle laser light scattering was used to characterize these formulations in terms of size distribution and homogeneity. The fractograms obtained at 37°C showed a polydisperse profile for all blank and ravuconazole–SEDDS formulations but no large aggregates. SEDDS increased ravuconazole in vitro dissolution extent and rate (20% compared to free drug (3% in 6 h. The in vivo toxicity of blank SEDDS comprising Labrasol® surfactant in different concentrations and preliminary safety tests in repeated-dose oral administration (20 days showed a dose-dependent Labrasol toxicity in healthy mice. Ravuconazole–SEDDS at low surfactant content (10%, v/v in Trypanosoma cruzi-infected mice was safe during the 20-day treatment. The anti-T. cruzi activity of free ravuconazole

Enzymatic preparation and characterization of soybean lecithin-based emulsifiers; Preparación enzimática y caracterización de emulsionantes a base de lecitina de soja

Energy Technology Data Exchange (ETDEWEB)

Reddy Jala, R.C.; Chen, B.; Li, H.; Zhang, Y.; Cheong, L.Z.; Yang, T.; Xu, X.

2016-07-01

Simple enzymatic methods were developed for the synthesis of lysolecithin, glycerolyzed lecithin and hydrolyzed lecithin. The products were characterized in terms of their acetone insoluble matter, hexane insoluble matter, moisture, phospholipid distribution and fatty acid composition. The HLB value ranges of different products with different acid values were detected. The efficiency of optimally hydrolyzed lecithin was examined at high calcium ion, low pH, and aqueous solutions and compared with commercially available standard lecithin-based emulsifiers. Overall, lysolecithin powder was proven to be the best emulsifier even at strong and medium acidic conditions. [Spanish] Se han desarrollado métodos enzimáticos simples para la síntesis de lisolecitina, lecitina esterificada a glicerol y lecitina hidrolizada. Los productos se caracterizaron en términos de su composición en materia insoluble en acetona, materia insoluble en hexano, humedad, distribución de fosfolípidos y ácidos grasos. Además, se detectaron rangos de los valores de HLB de diferentes productos con valores de ácido diferentes. La eficiencia de la lecitina hidrolizada de forma óptima fue estudiada en función de una alta concentración de ion calcio, pH bajo, y soluciones acuosas y se compara con emulsionantes basados en lecitina estándar disponibles en el mercado. En general, el polvo de lisolecitina mostró ser el mejor emulsionante incluso en condiciones ácidas fuertes y medias.

Alpha-tocopheryl polyethylene glycol succinate-emulsified poly(lactic-co-glycolic acid) nanoparticles for reversal of multidrug resistance in vitro

International Nuclear Information System (INIS)

Wang Ying; Lu Yu; Ding Liying; Liu Yaqing; Yu Shuqin; Guo Miao; Ron Wenting; Song Feifei

2012-01-01

Multidrug resistance (MDR) is one of the factors in the failure of anticancer chemotherapy. In order to enhance the anticancer effect of P-glycoprotein (P-gp) substrates, inhibition of the P-gp efflux pump on MDR cells is a good tactic. We designed novel multifunctional drug-loaded alpha-tocopheryl polyethylene glycol succinate (TPGS)/poly(lactic-co-glycolic acid) (PLGA) nanoparticles (TPGS/PLGA/SN-38 NPs; SN-38 is 7-ethyl-10-hydroxy-camptothecin), with TPGS-emulsified PLGA NPs as the carrier and modulator of the P-gp efflux pump and SN-38 as the model drug. TPGS/PLGA/SN-38 NPs were prepared using a modified solvent extraction/evaporation method. Physicochemical characterizations of TPGS/PLGA/SN-38 NPs were in conformity with the principle of nano-drug delivery systems (nDDSs), including a diameter of about 200 nm, excellent spherical particles with a smooth surface, narrow size distribution, appropriate surface charge, and successful drug-loading into the NPs. The cytotoxicity of TPGS/PLGA/SN-38 NPs to MDR cells was increased by 3.56 times compared with that of free SN-38. Based on an intracellular accumulation study relative to the time-dependent uptake and efflux inhibition, we suggest novel mechanisms of MDR reversal of TPGS/PLGA NPs. Firstly, TPGS/PLGA/SN-38 NPs improved the uptake of the loaded drug by clathrin-mediated endocytosis in the form of unbroken NPs. Simultaneously, intracellular NPs escaped the recognition of P-gp by MDR cells. After SN-38 was released from TPGS/PLGA/SN-38 NPs in MDR cells, TPGS or/and PLGA may modulate the efflux microenvironment of the P-gp pump, such as mitochondria and the P-gp domain with an ATP-binding site. Finally, the controlled-release drug entered the nucleus of the MDR cell to induce cytotoxicity. The present study showed that TPGS-emulsified PLGA NPs could be functional carriers in nDDS for anticancer drugs that are also P-gp substrates. More importantly, to enhance the therapeutic effect of P-gp substrates, this work

Determinação do fator de proteção solar (FPS in vitro e in vivo de emulsões com óleo de andiroba (Carapa guianensis

Directory of Open Access Journals (Sweden)

Márcio Ferrari

Full Text Available O óleo de andiroba extraído da Carapa guianensis tem apresentado considerável interesse pelas indústrias farmacêutica e cosmética devido a suas propriedades antiinflamatória e repelente de insetos. Esta pesquisa teve como objetivo avaliar a atividade fotoprotetora in vitro e in vivo do óleo de andiroba. Emulsões estáveis do tipo O/A foram preparadas com o metoxicinamato de etilhexila aditivadas ou não com óleo de andiroba. As características organolépticas foram avaliadas através de análises macroscópicas e o tipo de emulsão pelo teste de diluição. O FPS in vitro foi determinado pelo método espectrofotométrico desenvolvido por Mansur, e o teste in vivo de acordo com a metodologia padronizada pela Food and Drug Administration (FDA. Não houve diferença estatística entre as formulações, demonstrando que o óleo de andiroba não apresentou atividade fotoprotetora.

Adapting to the 30-degree visual perspective by emulating the angled laparoscope: a simple and low-cost solution for basic surgical training.

Science.gov (United States)

Daniel, Lorias Espinoza; Tapia, Fernando Montes; Arturo, Minor Martínez; Ricardo, Ordorica Flores

2014-12-01

The ability to handle and adapt to the visual perspectives generated by angled laparoscopes is crucial for skilled laparoscopic surgery. However, the control of the visual work space depends on the ability of the operator of the camera, who is often not the most experienced member of the surgical team. Here, we present a simple, low-cost option for surgical training that challenges the learner with static and dynamic visual perspectives at 30 degrees using a system that emulates the angled laparoscope. A system was developed using a low-cost camera and readily available materials to emulate the angled laparoscope. Nine participants undertook 3 tasks to test spatial adaptation to the static and dynamic visual perspectives at 30 degrees. Completing each task to a predefined satisfactory level ensured precision of execution of the tasks. Associated metrics (time and error rate) were recorded, and the performance of participants were determined. A total of 450 repetitions were performed by 9 residents at various stages of training. All the tasks were performed with a visual perspective of 30 degrees using the system. Junior residents were more proficient than senior residents. This system is a viable and low-cost alternative for developing the basic psychomotor skills necessary for the handling and adaptation to visual perspectives of 30 degrees, without depending on a laparoscopic tower, in junior residents. More advanced skills may then be acquired by other means, such as in the operating theater or through clinical experience.

Formulasi Sediaan Nano Herbal Tempuyung (Sonchus arvensis L. dalam Bentuk Self Nano-Emulsifying Drug Delivery System (SNEDDS

Directory of Open Access Journals (Sweden)

Budy Wijiyanto

2016-12-01

Full Text Available Tempuyung (Sonchus arvensis L. merupakan tanaman asli Indonesia yang berhkasiat sebagai diuretik dan antioksidan. Untuk mendapatkan efek terapi yang optimal perlu inovasi untuk membuatnya menjadi sediaan nano herbal. Penelitian ini bertujuan  membuat sediaan nano herbal tempuyung dalam bentuk Self Nano-Emulsifying Drug Delivery System (SNEDDS.  Kandungan zat aktif tempuyung diekstraksi dengan etanol dan berikut diuapkan pelarutnya untuk mendapatkan ekstrak kental. Ekstrak yang diperoleh distandarisasi menurut Farmakope Herbal Indonesia. Berikutnya dibuat SNEDDS tempuyung dengan menggunakan minyak Capryol-90, surfaktan tween 20 dan ko-surfaktan PEG 400. SNEDDS yang diperoleh dikarakterisasi meliputi ukuran partikel dan zeta potensial. Dari ekstraksi diperoleh ekstrak kental sebanyak 77,52 g. Hasil ini telah memenuhi syarat jika dibandingkan dengan Farmakope Herbal yang menyebutkan perolehan rendemen ekstrak kental daun tempuyung adalah tidak kurang dari 7,5%.  Formulasi tempuyung dalam bentuk sediaan SNEDDS diperoleh suatu nanoemulsi yang jernih dengan ukuran partikel 16,2 ± 1,06 nm dan nilai zeta potensial -37,48±0,74 mV. Dapat disimpulkan bahwa ekstrak tempuyung menghasilkan suatu nano herbal dalam bentuk sediaan SNEDDS.

Emulating natural disturbances for declining late-successional species: A case study of the consequences for Cerulean Warblers (Setophaga cerulea)

Science.gov (United States)

Boves, Than J.; Buehler, David A.; Sheehan, James; Wood, Petra Bohall; Rodewald, Amanda D.; Larkin, Jeffrey L.; Keyser, Patrick D.; Newell, Felicity L.; George, Gregory A.; Bakermans, Marja H.; Evans, Andrea; Beachy, Tiffany A.; McDermott, Molly E.; Perkins, Kelly A.; White, Matthew; Wigley, T. Bently

2013-01-01

Forest cover in the eastern United States has increased over the past century and while some late-successional species have benefited from this process as expected, others have experienced population declines. These declines may be in part related to contemporary reductions in small-scale forest interior disturbances such as fire, windthrow, and treefalls. To mitigate the negative impacts of disturbance alteration and suppression on some late-successional species, strategies that emulate natural disturbance regimes are often advocated, but large-scale evaluations of these practices are rare. Here, we assessed the consequences of experimental disturbance (using partial timber harvest) on a severely declining late-successional species, the cerulean warbler (Setophaga cerulea), across the core of its breeding range in the Appalachian Mountains. We measured numerical (density), physiological (body condition), and demographic (age structure and reproduction) responses to three levels of disturbance and explored the potential impacts of disturbance on source-sink dynamics. Breeding densities of warblers increased one to four years after all canopy disturbances (vs. controls) and males occupying territories on treatment plots were in better condition than those on control plots. However, these beneficial effects of disturbance did not correspond to improvements in reproduction; nest success was lower on all treatment plots than on control plots in the southern region and marginally lower on light disturbance plots in the northern region. Our data suggest that only habitats in the southern region acted as sources, and interior disturbances in this region have the potential to create ecological traps at a local scale, but sources when viewed at broader scales. Thus, cerulean warblers would likely benefit from management that strikes a landscape-level balance between emulating natural disturbances in order to attract individuals into areas where current structure is

Book Review Emulation real estate values ​​and territorial dynamics / Reseña del libro Emulación del valor inmobiliario y dinámica territorial

Directory of Open Access Journals (Sweden)

Adolfo Benito Narváez Tijerina

2011-09-01

Full Text Available Reseña del libro: "Emulación del valor inmobiliario y dinámica territorial", de Jesús Manuel Fitch Osuna, Monterrey, Universidad Autónoma de Nuevo León-UPC, 2010. Book Review: "Emulation real estate values ​​and territorial dynamics," Jesus Manuel Fitch Osuna, Monterrey, Universidad Autonoma de Nuevo Leon-UPC, 2010.

Pinatubo Emulation in Multiple Models (POEMs): co-ordinated experiments in the ISA-MIP model intercomparison activity component of the SPARC Stratospheric Sulphur and it's Role in Climate initiative (SSiRC)

Science.gov (United States)

Lee, Lindsay; Mann, Graham; Carslaw, Ken; Toohey, Matthew; Aquila, Valentina

2016-04-01

The World Climate Research Program's SPARC initiative has a new international activity "Stratospheric Sulphur and its Role in Climate" (SSiRC) to better understand changes in stratospheric aerosol and precursor gaseous sulphur species. One component of SSiRC involves an intercomparison "ISA-MIP" of composition-climate models that simulate the stratospheric aerosol layer interactively. Within PoEMS each modelling group will run a "perturbed physics ensemble" (PPE) of interactive stratospheric aerosol (ISA) simulations of the Pinatubo eruption, varying several uncertain parameters associated with the eruption's SO2 emissions and model processes. A powerful new technique to quantify and attribute sources of uncertainty in complex global models is described by Lee et al. (2011, ACP). The analysis uses Gaussian emulation to derive a probability density function (pdf) of predicted quantities, essentially interpolating the PPE results in multi-dimensional parameter space. Once trained on the ensemble, a Monte Carlo simulation with the fast Gaussian emulator enabling a full variance-based sensitivity analysis. The approach has already been used effectively by Carslaw et al., (2013, Nature) to quantify the uncertainty in the cloud albedo effect forcing from a 3D global aerosol-microphysics model allowing to compare the sensitivy of different predicted quantities to uncertainties in natural and anthropogenic emissions types, and structural parameters in the models. Within ISA-MIP, each group will carry out a PPE of runs, with the subsequent analysis with the emulator assessing the uncertainty in the volcanic forcings predicted by each model. In this poster presentation we will give an outline of the "PoEMS" analysis, describing the uncertain parameters to be varied and the relevance to further understanding differences identified in previous international stratospheric aerosol assessments.

Self nano-emulsifying drug delivery system for Embelin: Design, characterization and in-vitro studies

Directory of Open Access Journals (Sweden)

Komal Parmar

2015-10-01

Full Text Available CThe objective of the present study was to prepare solid self-nanoemulsifying drug delivery system (S-SNEDDS containing Capryol-90 as oil phase for the delivery of Embelin, a poorly water soluble herbal active ingredient. Box-Behnken experimental design was employed to optimise the formulation variables, X1 (amount of oil; Capryol 90, X2 (amount of surfactant; Acrysol EL 135 and X3 (amount of co-surfactant; PEG 400. Systems were appraised for visual characteristics for self emulsifying time, globule size and drug release. Optimised liquid formulations were formulated into free flowing granules (S-SNEDDS by adsorption on the porous materials like Aerosil 200 and Neusilin and thereby compressed into tablet. In vitro dissolution studies of SNEDDS revealed increased in the dissolution rate of the drug. FT-IR data revealed no physicochemical interaction between drug and excipients. Solid state characterization of S-SNEDDS by DSC and Powder XRD confirmed reduction in drug crystallinity which further supports the results of dissolution studies. TEM analysis exhibited spherical globules. Further, the accelerated stability studies for 6 months revealed that S-SNEDDS of Embelin are found to be stable without any significant change in physicochemical properties. Thus, the present studies demonstrated dissolution enhancement potential of porous carrier based S-SNEDDS for poorly water soluble herbal active ingredient, Embelin.

Comparison of high-resolution ultrasonic resonator technology and Raman spectroscopy as novel process analytical tools for drug quantification in self-emulsifying drug delivery systems.

Science.gov (United States)

Stillhart, Cordula; Kuentz, Martin

2012-02-05

Self-emulsifying drug delivery systems (SEDDS) are complex mixtures in which drug quantification can become a challenging task. Thus, a general need exists for novel analytical methods and a particular interest lies in techniques with the potential for process monitoring. This article compares Raman spectroscopy with high-resolution ultrasonic resonator technology (URT) for drug quantification in SEDDS. The model drugs fenofibrate, indomethacin, and probucol were quantitatively assayed in different self-emulsifying formulations. We measured ultrasound velocity and attenuation in the bulk formulation containing drug at different concentrations. The formulations were also studied by Raman spectroscopy. We used both, an in-line immersion probe for the bulk formulation and a multi-fiber sensor for measuring through hard-gelatin capsules that were filled with SEDDS. Each method was assessed by calculating the relative standard error of prediction (RSEP) as well as the limit of quantification (LOQ) and the mean recovery. Raman spectroscopy led to excellent calibration models for the bulk formulation as well as the capsules. The RSEP depended on the SEDDS type with values of 1.5-3.8%, while LOQ was between 0.04 and 0.35% (w/w) for drug quantification in the bulk. Similarly, the analysis of the capsules led to RSEP of 1.9-6.5% and LOQ of 0.01-0.41% (w/w). On the other hand, ultrasound attenuation resulted in RSEP of 2.3-4.4% and LOQ of 0.1-0.6% (w/w). Moreover, ultrasound velocity provided an interesting analytical response in cases where the drug strongly affected the density or compressibility of the SEDDS. We conclude that ultrasonic resonator technology and Raman spectroscopy constitute suitable methods for drug quantification in SEDDS, which is promising for their use as process analytical technologies. Copyright © 2011 Elsevier B.V. All rights reserved.

Preparation of Fe{sub 3}O{sub 4}/poly(styrene-butyl acrylate-[2-(methacryloxy)ethyl]trimethylammonium chloride) by emulsifier-free emulsion polymerization and its interaction with DNA

Energy Technology Data Exchange (ETDEWEB)

Li Xiaolong; Liu Guoqiang; Yan Wei [Ministry-of-Education Key Laboratory for the Green Preparation and Application of Functional Materials, Hubei University, Wuhan (China); Chu, Paul K. [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon (Hong Kong); Yeung, Kelvin W.K. [Division of Spine Surgery, Department of Orthopaedics and Traumatology, The University of Hong Kong, Pokfulam (Hong Kong); Wu Shuilin; Yi Changfeng [Ministry-of-Education Key Laboratory for the Green Preparation and Application of Functional Materials, Hubei University, Wuhan (China); Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon (Hong Kong); Division of Spine Surgery, Department of Orthopaedics and Traumatology, The University of Hong Kong, Pokfulam (Hong Kong); Xu Zushun, E-mail: zushun25@yahoo.com.cn [Ministry-of-Education Key Laboratory for the Green Preparation and Application of Functional Materials, Hubei University, Wuhan (China); Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon (Hong Kong); Division of Spine Surgery, Department of Orthopaedics and Traumatology, University of Hong Kong, Pokfulam (Hong Kong)

2012-04-15

Cationic magnetic polymer particles Fe{sub 3}O{sub 4}/poly(styrene-butyl acrylate-[2-(methacryloxy)ethyl]trimethylammonium chloride), a type of potential gene carrier, were prepared by emulsifier-free emulsion polymerization with oleic acid modified magnetite Fe{sub 3}O{sub 4}, styrene, butyl acrylate and [2-(methacryloxy)ethyl]trimethylammonium chloride) (METAC). The morphology of the particles was characterized by transmission electron microscopy and the composites of particles were characterized by FT-IR spectroscopy, X-ray diffraction. These results showed that magnetic particles were well dispersed in polymers with the content of about 15%(wt/wt). The composites exhibited superparamagnetism and possessed a certain level of magnetic response. The interactions between the particles with calf-thymus DNA (ct DNA) were confirmed by zeta potential measurement, UV-vis spectroscopy and fluorescence spectroscopy. The DNA-binding capacity determined by the agarose gel electrophoresis showed good binding capacity of the emulsion to DNA. These results suggested the potential of the cationic magnetic polymer emulsion as gene target delivery carrier. - Highlights: Black-Right-Pointing-Pointer A new type of cationic magnetic polymer particles was synthesized by emulsifier-free emulsion polymerization. Black-Right-Pointing-Pointer Structural, morphological, and magnetic properties of the composite were evaluated. Black-Right-Pointing-Pointer The interaction between cationic magnetic polymer particles with DNA was confirmed by zeta potential measurements. Black-Right-Pointing-Pointer UV-vis spectrophotometry, fluorescent spectroscopy and agarose gel electrophoresis. Black-Right-Pointing-Pointer This process may have potential applications to gene carrier and DNA separation.

Removal of emulsified and dissolved traces of organic compounds from industrial wastewaters using nature and synthesized (Na A and Nam) zeolites

International Nuclear Information System (INIS)

Modirshahla, N.; Tabatabaii, S.

2004-01-01

The main object of this study was to compare the natural and synthetic (Na A and Nam) zeolites as absorbents in removing emulsified and dissolved traces of organic compounds, which appear in the wastewater of power plants, refinery and petrochemical complexes. The specific objections of the work was: a) to select the best species that have the highest amount of absorption; b) to measure the rate of absorption of traces organic compounds and emulsions on the natural and synthesized zeolites; c) to establish the absorption isotherms for the organics and emulsions with selected samples; d) to select readily available regenerants, and e ) to examine the ph dependence of the process and to establish a simple and practical method to detect and to measure the pollution after the treatment process. The BOD and COD of the treated and feed waters were compared

Lipid oxidation in base algae oil and water-in-algae oil emulsion: Impact of natural antioxidants and emulsifiers.

Science.gov (United States)

Chen, Bingcan; Rao, Jiajia; Ding, Yangping; McClements, David Julian; Decker, Eric Andrew

2016-07-01

The impact of natural hydrophilic antioxidants, metal chelators, and hydrophilic antioxidant/metal chelator mixture on the oxidative stability of base algae oil and water-in-algae oil emulsion was investigated. The results showed that green tea extract and ascorbic acid had greatest protective effect against algae oil oxidation and generated four day lag phase, whereas rosmarinic acid, grape seed extract, grape seed extract polymer, deferoxamine (DFO), and ethylenediaminetetraacetic acid (EDTA) had no significant protective effect. Besides, there was no synergistic effect observed between natural antioxidants and ascorbic acid. The emulsifiers are critical to the physicochemical stability of water-in-algae oil emulsions. Polyglycerol polyricinoleate (PGPR) promoted the oxidation of emulsion. Conversely, the protective effect on algae oil oxidation was appreciated when defatted soybean lecithin (PC 75) or defatted lyso-lecithin (Lyso-PC) was added. The role of hydrophilic antioxidants in emulsion was similar to that in algae oil except EDTA which demonstrated strong antioxidative effect in emulsion. The results could provide information to build up stable food products containing polyunsaturated fatty acids (PUFA). Copyright © 2016 Elsevier Ltd. All rights reserved.

CHARACTERIZING THE FORMATION HISTORY OF MILKY WAY LIKE STELLAR HALOS WITH MODEL EMULATORS

International Nuclear Information System (INIS)

Gómez, Facundo A.; O'Shea, Brian W.; Coleman-Smith, Christopher E.; Tumlinson, Jason; Wolpert, Robert L.

2012-01-01

We use the semi-analytic model ChemTreeN, coupled to cosmological N-body simulations, to explore how different galaxy formation histories can affect observational properties of Milky Way like galaxies' stellar halos and their satellite populations. Gaussian processes are used to generate model emulators that allow one to statistically estimate a desired set of model outputs at any location of a p-dimensional input parameter space. This enables one to explore the full input parameter space orders of magnitude faster than could be done otherwise. Using mock observational data sets generated by ChemTreeN itself, we show that it is possible to successfully recover the input parameter vectors used to generate the mock observables if the merger history of the host halo is known. However, our results indicate that for a given observational data set, the determination of 'best-fit' parameters is highly susceptible to the particular merger history of the host. Very different halo merger histories can reproduce the same observational data set, if the 'best-fit' parameters are allowed to vary from history to history. Thus, attempts to characterize the formation history of the Milky Way using these kind of techniques must be performed statistically, analyzing large samples of high-resolution N-body simulations.

Self-assembly, foaming, and emulsifying properties of sodium alkyl carboxylate/guanidine hydrochloride aqueous mixtures.

Science.gov (United States)

Fameau, Anne-Laure; Houinsou-Houssou, Bérénice; Ventureira, Jorge Luis; Navailles, Laurence; Nallet, Frédéric; Novales, Bruno; Douliez, Jean-Paul

2011-04-19

Unsaturated fatty acids may be extracted from various agricultural resources and are widely used as soaps in the industry. However, there also exist a large variety of saturated and hydroxy fatty acids in nature, but their metal salts crystallize at room temperature in water, hampering their use in biological and chemical studies or for industrial applications. Addition of guanidine hydrochloride (GuHCl) to sodium salt of myristic acid has been shown to prevent its crystallization in water, forming stable flat bilayers at room temperature. Herein, we extend this finding to two other saturated fatty acids (palmitic and stearic acids) and two hydroxyl fatty acids (juniperic and 12 hydroxy stearic acids) and study more deeply (by using small angle neutron scattering) the supramolecular assemblies formed in both saturated and hydroxyl fatty acid systems. In addition, we take the advantage that crystallization no longer occurs at room temperature in the presence of GuHCl to study the foaming and emulsifying properties of those fatty acid dispersions. Briefly, our results show that all fatty acids, even juniperic acid, which is a bola lipid, are arranged in a bilayer structure that may be interdigitated. Depending on the nature of the fatty acid, the systems exhibit good foamability and foam stability (except for juniperic acid), and emulsion stability was good. Those findings should be of interest for using saturated long chain (and hydroxyl) fatty acids as surfactants for detergency or even materials chemistry. © 2011 American Chemical Society

Mycobacteria emulsified in olive oil-in-water trigger a robust immune response in bladder cancer treatment

Science.gov (United States)

Noguera-Ortega, Estela; Blanco-Cabra, Núria; Rabanal, Rosa Maria; Sánchez-Chardi, Alejandro; Roldán, Mónica; Guallar-Garrido, Sandra; Torrents, Eduard; Luquin, Marina; Julián, Esther

2016-01-01

The hydrophobic composition of mycobacterial cell walls leads to the formation of clumps when attempting to resuspend mycobacteria in aqueous solutions. Such aggregation may interfere in the mycobacteria-host cells interaction and, consequently, influence their antitumor effect. To improve the immunotherapeutic activity of Mycobacterium brumae, we designed different emulsions and demonstrated their efficacy. The best formulation was initially selected based on homogeneity and stability. Both olive oil (OO)- and mineral oil-in-water emulsions better preserved the mycobacteria viability and provided higher disaggregation rates compared to the others. But, among both emulsions, the OO emulsion increased the mycobacteria capacity to induce cytokines’ production in bladder tumor cell cultures. The OO-mycobacteria emulsion properties: less hydrophobic, lower pH, more neutralized zeta potential, and increased affinity to fibronectin than non-emulsified mycobacteria, indicated favorable conditions for reaching the bladder epithelium in vivo. Finally, intravesical OO-M. brumae-treated mice showed a significantly higher systemic immune response, together with a trend toward increased tumor-bearing mouse survival rates compared to the rest of the treated mice. The physicochemical characteristics and the induction of a robust immune response in vitro and in vivo highlight the potential of the OO emulsion as a good delivery vehicle for the mycobacterial treatment of bladder cancer. PMID:27265565

Equivalence of Primary Control Strategies for AC and DC Microgrids

Directory of Open Access Journals (Sweden)

Eneko Unamuno

2017-01-01

Full Text Available Microgrid frequency and voltage regulation is a challenging task, as classical generators with rotational inertia are usually replaced by converter-interfaced systems that inherently do not provide any inertial response. The aim of this paper is to analyse and compare autonomous primary control techniques for alternating current (AC and direct current (DC microgrids that improve this transient behaviour. In this context, a virtual synchronous machine (VSM technique is investigated for AC microgrids, and its behaviour for different values of emulated inertia and droop slopes is tested. Regarding DC microgrids, a virtual-impedance-based algorithm inspired by the operation concept of VSMs is proposed. The results demonstrate that the proposed strategy can be configured to have an analogous behaviour to VSM techniques by varying the control parameters of the integrated virtual-impedances. This means that the steady-state and transient behaviour of converters employing these strategies can be configured independently. As shown in the simulations, this is an interesting feature that could be, for instance, employed for the integration of different dynamic generation or storage systems, such as batteries or supercapacitors.

Approaches for scalable modeling and emulation of cyber systems : LDRD final report.

Energy Technology Data Exchange (ETDEWEB)

Mayo, Jackson R.; Minnich, Ronald G.; Armstrong, Robert C.; Rudish, Don W.

2009-09-01

The goal of this research was to combine theoretical and computational approaches to better understand the potential emergent behaviors of large-scale cyber systems, such as networks of {approx} 10{sup 6} computers. The scale and sophistication of modern computer software, hardware, and deployed networked systems have significantly exceeded the computational research community's ability to understand, model, and predict current and future behaviors. This predictive understanding, however, is critical to the development of new approaches for proactively designing new systems or enhancing existing systems with robustness to current and future cyber threats, including distributed malware such as botnets. We have developed preliminary theoretical and modeling capabilities that can ultimately answer questions such as: How would we reboot the Internet if it were taken down? Can we change network protocols to make them more secure without disrupting existing Internet connectivity and traffic flow? We have begun to address these issues by developing new capabilities for understanding and modeling Internet systems at scale. Specifically, we have addressed the need for scalable network simulation by carrying out emulations of a network with {approx} 10{sup 6} virtualized operating system instances on a high-performance computing cluster - a 'virtual Internet'. We have also explored mappings between previously studied emergent behaviors of complex systems and their potential cyber counterparts. Our results provide foundational capabilities for further research toward understanding the effects of complexity in cyber systems, to allow anticipating and thwarting hackers.

Emulation and Calibration of the SALT Read-out Chip for the Upstream Tracker for Modernised LHCb Detector

CERN Document Server

Dendek, Adam

2015-01-01

The LHCb is one of the four major experiments currently operating at CERN. The main reason for constructing the LHCb forward spectrometer was a precise measurement of the CP violation in heavy quarks section as well as search for a New Physics. To obtain interesting results, the LHCb is mainly focused on study of B meson decays. Unfortunately, due to the present data acquisition architecture, the LHCb experiment is statistically limited for collecting such events. This fact led the LHCb Collaboration to decide to perform far-reaching upgrade. Key part of this upgrade will be replacement of the TT detector. To perform this action, it was requited to design new tracking detector with entirely new front-end electronics. This detector will be called the Upstream Tracker (UT) and the read-out chip — SALT. This note presents an overall discussion on SALT chip. In particular, the emulation process of the SALT data preformed via the software written by the author.

Meta-modelling, visualization and emulation of multi-dimensional data for virtual production intelligence

Science.gov (United States)

Schulz, Wolfgang; Hermanns, Torsten; Al Khawli, Toufik

2017-07-01

Decision making for competitive production in high-wage countries is a daily challenge where rational and irrational methods are used. The design of decision making processes is an intriguing, discipline spanning science. However, there are gaps in understanding the impact of the known mathematical and procedural methods on the usage of rational choice theory. Following Benjamin Franklin's rule for decision making formulated in London 1772, he called "Prudential Algebra" with the meaning of prudential reasons, one of the major ingredients of Meta-Modelling can be identified finally leading to one algebraic value labelling the results (criteria settings) of alternative decisions (parameter settings). This work describes the advances in Meta-Modelling techniques applied to multi-dimensional and multi-criterial optimization by identifying the persistence level of the corresponding Morse-Smale Complex. Implementations for laser cutting and laser drilling are presented, including the generation of fast and frugal Meta-Models with controlled error based on mathematical model reduction Reduced Models are derived to avoid any unnecessary complexity. Both, model reduction and analysis of multi-dimensional parameter space are used to enable interactive communication between Discovery Finders and Invention Makers. Emulators and visualizations of a metamodel are introduced as components of Virtual Production Intelligence making applicable the methods of Scientific Design Thinking and getting the developer as well as the operator more skilled.

Emulation and Sobol' sensitivity analysis of an atmospheric dispersion model applied to the Fukushima nuclear accident

Science.gov (United States)

Girard, Sylvain; Mallet, Vivien; Korsakissok, Irène; Mathieu, Anne

2016-04-01

Simulations of the atmospheric dispersion of radionuclides involve large uncertainties originating from the limited knowledge of meteorological input data, composition, amount and timing of emissions, and some model parameters. The estimation of these uncertainties is an essential complement to modeling for decision making in case of an accidental release. We have studied the relative influence of a set of uncertain inputs on several outputs from the Eulerian model Polyphemus/Polair3D on the Fukushima case. We chose to use the variance-based sensitivity analysis method of Sobol'. This method requires a large number of model evaluations which was not achievable directly due to the high computational cost of Polyphemus/Polair3D. To circumvent this issue, we built a mathematical approximation of the model using Gaussian process emulation. We observed that aggregated outputs are mainly driven by the amount of emitted radionuclides, while local outputs are mostly sensitive to wind perturbations. The release height is notably influential, but only in the vicinity of the source. Finally, averaging either spatially or temporally tends to cancel out interactions between uncertain inputs.