The certification of boron in primary ingot aluminium. BCR No.25

International Nuclear Information System (INIS)

Vandecasteele, C.; Colinet, E.

1984-01-01

This report sets out the experimental procedures used for the certification of boron in primary ingot aluminium, which has already been certified for carbon and oxygen. Samples were analysed by seven different laboratories using the following methods: spectrophotometry, ICP-emission spectrometry, isotope dilution mass spectrometry, spark source mass spectrometry and charged particle activation analysis. The analytical methods and the statistical approach to analyse the data are described

Investigation of aluminium-rich alloy system of aluminium-strontium-silicium

International Nuclear Information System (INIS)

Ganiev, I.N.; Vakhobov, A.B.; Dzhuraev, T.D.; Alidzhanov, F.N.

1976-01-01

An area of the solid solution based on aluminium was studied, and the surface was plotted of the liquidus adjoining the apex of the aluminium corner of the strontium-aluminium-silicon system. The investigation was carried out by microstructure and differential thermal analyses and by the measurement of the microhardness of the component phases. A combined solubility of silicon and strontium in aluminium was studied along three radial sections at Sr-to-Si ratios of 1/2, 1/1 and 2/1. The relationships of ''composition vs. Microhardness'', obtained in these sections, made it possible to define the boundaries of the phase regions in the aluminium corner of the strontium-aluminium-silicon system at 500 deg C. The greatest solubility is that along the Al-SrAl 2 Si 2 section at a Sr/Si ratio of 1/2. A further increase in the content of strontium brings about a drop in the solubility of silicon in solid aluminium. The projection of the liquidus surface of the strontium-aluminium-silicon system, rich in aluminium, includes four surfaces of primary crystallization: α-Al, SrAl 4 , SrAl 2 Si 2 and Si. The system comprises a section of Al-SrAl 2 Si 2 representing a quasibinary system of an eutectic type. The eutectic reaction takes place at a temperature of 640 deg C. The quasibinary Al-SrAl 2 Si 2 section divides the aluminium corner of the Sr-Al-Si system into two independent systems Al-SrAl 4 -SrAl 2 Si 2 and Al-Si-SrAl 2 Si 2 of an eutectic type

Effects of zinc smelter emissions on farms and gardens at Palmerton, PA

Science.gov (United States)

Chaney, R.L.; Beyer, W.N.; Gifford, C.H.; Sileo, L.

1988-01-01

In 1979, before the primary Zn smelter at Palmerton was closed due to excessive Zn and Cd emissions and change in the price of Zn, we were contacted by a local veterinarian regarding death of foals (young horses) on farms near the smelter. To examine whether Zn or Cd contamination of forage or soils could be providing potentially toxic levels of Zn or other elements in the diets of foals, we measured metals in forages, soils, and feces of grazing livestock on two farms near Palmerton. The farms were about 2.5 and about 10 km northeast of the East stack. Soils, forages, and feces were greatly increased in Zn and Cd. Soil, forage, and fecal Zn were near 1000 mg/kg and Cd, 10-20 mg/kg at farm A (2.5 km) compared to normal background levels of 43 mg Zn and 0.2 mg Cd/kg, respectively. Liver and kidney of cattle raised on Farm A were increased in Zn and Cd, indicating that at least part of the Zn and Cd in smelter contaminated forages was bioavailable. During the farm sampling, we obtained soil from one garden in Palmerton within 200 m of the primary (West) smelter. The Borough surrounds the smelter facility in a valley. Because soil Cd was near 100 mg/kg, we sampled garden soils and vegetables from over 40 gardens in 6 randomly selected blocks and in rural areas at different distances from the smelter during September, 1980. All homes were contacted on each sampled block. Nearly all homes had some garden, while at least 2 appeared to grow over 50% of their annual vegetable and potato consumption. Palmerton garden soils averaged 76 mg Cd/kg and 5830 mg Zn/kg. Gardeners had been taught to add limestone and organic fertilizers to counteract yield reduction and chlorosis due to the excessive soil Zn. Gardens with over 5000 mg Zn/kg were nearly allover pH 7, and many were calcareous. Because the smelter had not yet ceased operations in 1980, crops could have been polluted by aerosol Zn and Cd emitted by the smelter. Crop Zn and Cd were extremely high, about 100 times normal

Impact of Site Elevation on Mg Smelter Design

Science.gov (United States)

Baker, Phillip W.

Site elevation has many surprising and significant impacts on the engineering design of metallurgical plant of all types. Electrolytic magnesium smelters maybe built at high elevation for a variety of reasons including availability of raw material, energy or electric power. Because of the unit processes they typically involve, Mg smelters can be extensively impacted by site elevation. In this paper, generic examples of the design changes required to adapt a smelter originally designed for sea level to operate at 2700 m are presented. While the examples are drawn from a magnesium plant design case, these changes are generically applicable to all industrial plants utilizing similar unit processes irrespective of product.

A solidification/stabilization process for wastewater treatment sludge from a primary copper smelter

Directory of Open Access Journals (Sweden)

Ivšić-Bajčeta Dragana

2013-01-01

Full Text Available Wastewater treatment sludge from primary copper smelter is characterized as hazardous waste that requires treatment prior disposal due to significant amount of heavy metals and arsenic. The aim of the presented study was to investigate the feasibility and the effectiveness of solidification/stabilization process of the sludge using fly ash and lime as binders. The effectiveness of the process was evaluated by Unconfined Compressive Strength (UCS testing, leaching tests (EN 12457-4 and Toxicity Characteristic Leaching Procedure (TCLP and Acid Neutralization Capacity (ANC test. All samples reached target UCS of 0.35 MPa. Calcium to silicon concentration ratio (cCa/cSi, determined by X-Ray Fluorescence (XRF analysis, was identified as main factor governing strength development. Inductively coupled plasma-optical emission spectrometry (ICP-OES analyses of solutions after leaching tests showed excellent stabilization of Cu, Ni, Pb and Zn (above 99 % and arsenic (above 90 % in samples with high Ca(OH2 content. Results of ANC test indicated that buffering capacity of solidified material linearly depended on Ca concentration in FA and lime. Sample with 20 % of binder heaving 50 % of FA and 50 % of lime met all requirements to be safely disposed. [Projekat Ministarstva nauke Republike Srbije, br. 34033

Bioavailability and uptake of smelter emissions in freshwater zooplankton in northeastern Washington, USA lakes using Pb isotope analysis and trace metal concentrations.

Science.gov (United States)

Child, A W; Moore, B C; Vervoort, J D; Beutel, M W

2018-07-01

The upper Columbia River and associated valley systems are highly contaminated with metal wastes from nearby smelting operations in Trail, British Columbia, Canada (Teck smelter), and to a lesser extent, Northport, Washington, USA (Le Roi smelter). Previous studies have investigated depositional patterns of airborne emissions from these smelters, and documented the Teck smelter as the primary metal contamination source. However, there is limited research directed at whether these contaminants are bioavailable to aquatic organisms. This study investigates whether smelter derived contaminants are bioavailable to freshwater zooplankton. Trace metal (Zn, Cd, As, Sb, Pb and Hg) concentrations and Pb isotope compositions of zooplankton and sediment were measured in lakes ranging from 17 to 144 km downwind of the Teck smelter. Pb isotopic compositions of historic ores used by both smelters are uniquely less radiogenic than local geologic formations, so when zooplankton assimilate substantial amounts of smelter derived metals their compositions deviate from local baseline compositions toward ore compositions. Sediment metal concentrations and Pb isotope compositions in sediment follow significant (p < 0.001) negative exponential and sigmoidal patterns, respectively, as distance from the Teck smelting operation increases. Zooplankton As, Cd, and Sb contents were related to distance from the Teck smelter (p < 0.05), and zooplankton Pb isotope compositions suggest As, Cd, Sb and Pb from historic and current smelter emissions are biologically available to zooplankton. Zooplankton from lakes within 86 km of the Teck facility display isotopic evidence that legacy ore pollution is biologically available for assimilation. However, without water column data our study is unable to determine if legacy contaminants are remobilized from lake sediments, or erosional pathways from the watershed. Copyright © 2018 Elsevier Ltd. All rights reserved.

Aluminum smelter-derived polycyclic aromatic hydrocarbons and flatfish health in the Kitimat marine ecosystem, British Columbia, Canada.

Science.gov (United States)

Johnson, Lyndal L; Ylitalo, Gina M; Myers, Mark S; Anulacion, Bernadita F; Buzitis, Jon; Collier, Tracy K

2015-04-15

From 2000-2004 a monitoring study was conducted to evaluate the impacts of aluminum smelter-derived polycyclic aromatic hydrocarbons (PAHs) on the health of fish in the marine waters of Kitimat, British Columbia, Canada. These waters are part of the historical fishing grounds of the Haisla First Nation, and since the 1950s the Alcan Primary Metal Company has operated an aluminum smelter at the head of the Kitimat Arm embayment. As a result, adjacent marine and estuarine sediments have been severely contaminated with a mixture of smelter-associated PAHs in the range of 10,000-100,000 ng/g dry wt. These concentrations are above those shown to cause adverse effects in fish exposed to PAHs in urban estuaries, but it was uncertain whether comparable effects would be seen at the Kitimat site due to limited bioavailability of smelter-derived PAHs. Over the 5-year study we conducted biennial collections of adult English sole (Parophrys vetulus) and sediment samples at the corresponding capture sites. Various tissue samples (e.g. liver, kidney, gonad, stomach contents) and bile were taken from each animal to determine levels of exposure and biological effects, and compare the uptake and toxicity of smelter-derived PAHs with urban mixtures of PAHs. Results showed significant intersite differences in concentrations of PAHs. Sole collected at sites nearest the smelter showed increased PAH exposure, as well as significantly higher prevalences of PAH-associated liver disease, compared to sites within Kitimat Arm that were more distant from the smelter. However, measures of PAH exposure (e.g., bile metabolites) were surprisingly high in sole from the reference sites outside of Kitimat Arm, though sediment and dietary PAHs at these sites were low, and fish from the areas showed no biological injury. PAH uptake, exposure, and biological effects in Kitimat English sole were relatively lower when compared to English sole collected from urban sites contaminated with PAH mixtures from

Trophic transfer potential of aluminium oxide nanoparticles using representative primary producer (Chlorella ellipsoides) and a primary consumer (Ceriodaphnia dubia)

International Nuclear Information System (INIS)

Pakrashi, Sunandan; Dalai, Swayamprava; Chandrasekaran, Natarajan; Mukherjee, Amitava

2014-01-01

Highlights: • Trophic transfer of alumina nanoparticles using Chlorella ellipsoides and Ceriodaphnia dubia. • Subtle alterations in the feeding behaviour of the daphnids. • Disruption the energy flow through the food chain. • Transmission electron microscopy validated the disrupted feeding behaviour. - Abstract: The transfer of nanoparticles through the food chain can lead to bioaccumulation and biomagnification resulting in a long term negative impact on the ecosystem functions. The primary objective of this study was evaluation of aluminium oxide nanoparticles transfer from primary producers to primary consumers. A simple set up consisting of a primary producer (Chlorella ellipsoides) and a primary consumer (Ceriodaphnia dubia) was used. Here, C. ellipsoides were exposed to the varying concentrations of the nanoparticles ranging from 20 to 120 μg/mL (196 to 1176 μM) for 48 h and the infested algal cells were used as the feed to C. dubia. The bioaccumulation of the nanoparticles into the daphnids was noted and the biomagnification factors were computed. The exposure was noted to cause subtle alterations in the feeding behaviour of the daphnids. This might have long term consequences in the energy flow through the food chain. The reproductive behaviour of the daphnids remained unaffected upon exposure to nanoparticle infested algal feed. Distinct observations at ultra-structural scale using transmission electron microscopy provided visual evidences for the disrupted feeding behaviour upon exposure to nanoparticle treated algae. Internalization of nanoparticle like inclusion bodies in the intracellular space of algae was also detected. The findings were further substantiated by a detailed analysis of hydrodynamic stability, bioavailability and dissolution of ions from the nanoparticles over the exposure period. Altogether, the study brings out the first of its kind of observation of trophic transfer potential/behaviour of aluminium oxide nanoparticles and

Trophic transfer potential of aluminium oxide nanoparticles using representative primary producer (Chlorella ellipsoides) and a primary consumer (Ceriodaphnia dubia)

Energy Technology Data Exchange (ETDEWEB)

Pakrashi, Sunandan; Dalai, Swayamprava; Chandrasekaran, Natarajan; Mukherjee, Amitava, E-mail: amit.mookerjea@gmail.com

2014-07-01

Highlights: • Trophic transfer of alumina nanoparticles using Chlorella ellipsoides and Ceriodaphnia dubia. • Subtle alterations in the feeding behaviour of the daphnids. • Disruption the energy flow through the food chain. • Transmission electron microscopy validated the disrupted feeding behaviour. - Abstract: The transfer of nanoparticles through the food chain can lead to bioaccumulation and biomagnification resulting in a long term negative impact on the ecosystem functions. The primary objective of this study was evaluation of aluminium oxide nanoparticles transfer from primary producers to primary consumers. A simple set up consisting of a primary producer (Chlorella ellipsoides) and a primary consumer (Ceriodaphnia dubia) was used. Here, C. ellipsoides were exposed to the varying concentrations of the nanoparticles ranging from 20 to 120 μg/mL (196 to 1176 μM) for 48 h and the infested algal cells were used as the feed to C. dubia. The bioaccumulation of the nanoparticles into the daphnids was noted and the biomagnification factors were computed. The exposure was noted to cause subtle alterations in the feeding behaviour of the daphnids. This might have long term consequences in the energy flow through the food chain. The reproductive behaviour of the daphnids remained unaffected upon exposure to nanoparticle infested algal feed. Distinct observations at ultra-structural scale using transmission electron microscopy provided visual evidences for the disrupted feeding behaviour upon exposure to nanoparticle treated algae. Internalization of nanoparticle like inclusion bodies in the intracellular space of algae was also detected. The findings were further substantiated by a detailed analysis of hydrodynamic stability, bioavailability and dissolution of ions from the nanoparticles over the exposure period. Altogether, the study brings out the first of its kind of observation of trophic transfer potential/behaviour of aluminium oxide nanoparticles and

Utilization of red mud and Pb/Zn smelter waste for the synthesis of a red mud-based cementitious material.

Science.gov (United States)

Li, Yuan-Cheng; Min, Xiao-Bo; Ke, Yong; Chai, Li-Yuan; Shi, Mei-Qing; Tang, Chong-Jian; Wang, Qing-Wei; Liang, Yan-Jie; Lei, Jie; Liu, De-Gang

2018-02-15

A new method in which Pb/Zn smelter waste containing arsenic and heavy metals (arsenic sludge), red mud and lime are utilized to prepare red mud-based cementitious material (RCM) is proposed in this study. XRD, SEM, FTIR and unconfined compressive strength (UCS) tests were employed to assess the physicochemical properties of RCM. In addition, ettringite and iron oxide-containing ettringite were used to study the hydration mechanism of RCM. The results show that the UCS of the RCM (red mud+arsenic sludge+lime) was higher than that of the binder (red mud+arsenic sludge). When the mass ratio of m (binder): m (lime) was 94:6 and then maintained 28days at ambient temperature, the UCS reached 12.05MPa. The red mud has potential cementitious characteristics, and the major source of those characteristics was the aluminium oxide. In the red mud-arsenic sludge-lime system, aluminium oxide was effectively activated by lime and gypsum to form complex hydration products. Some of the aluminium in ettringite was replaced by iron to form calcium sulfoferrite hydrate. The BCR and leaching toxicity results show that the leaching concentration was strongly dependent on the chemical speciation of arsenic and the hydration products. Therefore, the investigated red mud and arsenic sludge can be successfully utilized in cement composites to create a red mud-based cementitious material. Copyright © 2017 Elsevier B.V. All rights reserved.

Environmental Exposure to Arsenic, Lead, and Cadmium in People Living near Janghang Copper Smelter in Korea.

Science.gov (United States)

Kim, Yong-Dae; Eom, Sang-Yong; Yim, Dong-Hyuk; Kim, In-Soo; Won, Hee-Kwan; Park, Choong-Hee; Kim, Guen-Bae; Yu, Seung-Do; Choi, Byung-Sun; Park, Jung-Duck; Kim, Heon

2016-04-01

Concentrations of heavy metals exceed safety thresholds in the soil near Janghang Copper Refinery, a smelter in Korea that operated from 1936 to 1989. This study was conducted to evaluate the level of exposure to toxic metals and the potential effect on health in people living near the smelter. The study included 572 adults living within 4 km of the smelter and compared them with 413 controls group of people living similar lifestyles in a rural area approximately 15 km from the smelter. Urinary arsenic (As) level did not decrease according to the distance from the smelter, regardless of gender and working history in smelters and mines. However, in subjects who had no occupational exposure to toxic metals, blood lead (Pb) and cadmium (Cd) and urinary Cd decreased according to the distance from the smelter, both in men and women. Additionally, the distance from the smelter was a determinant factor for a decrease of As, Pb, and Cd in multiple regression models, respectively. On the other hands, urinary Cd was a risk factor for renal tubular dysfunction in populations living near the smelter. These results suggest that Janghang copper smelter was a main contamination source of As, Pb, and Cd, and populations living near the smelter suffered some adverse health effects as a consequence. The local population should be advised to make efforts to reduce exposure to environmental contaminants, in order to minimize potential health effects, and to pay close attention to any health problems possibly related to toxic metal exposure.

Arsenic pollution in the Yellowknife area from gold smelter activities

International Nuclear Information System (INIS)

Hutchinson, T.C.; Aufreiter, S.; Hancock, R.G.V.

1982-01-01

Gold mined at Yelloknife in the North West Territories of Canada is associated with arsenopyrite ores which necessitates the oxidation of the arsenic and sulphur by roasting at two Yellowknife smelters. As 2 O 3 and SO 2 are emitted into the atmosphere, and despite improvements in emission control, significant emissions still occur. In order to asses the arsenic contamination in the local environment and the potential exposures to man, soil samples and samples of the native vegetation were collected in and around Yellowknife and the two smelters. Arsenic and antimony analyses were done by instrumental neutron activation analysis using the SLOWPOKE facility at University of Toronto. Zinc, copper, lead and cadmium analyses were done by atomic adsorption spectrophotometry. Arsenic was found to be accumulated in the soils in the vicinity of the two smelters to levels of several thousand ppm. Antimony levels were about 10% of arsenic and were highly correlated with arsenic. Zinc occured to 500 ppm around the smelters. Soil arsenic levels are sufficiently high to inhibit root growth in soils over a very extensive area. (author)

Lead exposure in children living in a smelter community in region Lagunera, Mexico.

Science.gov (United States)

García Vargas, G G; Rubio Andrade, M; Del Razo, L M; Borja Aburto, V; Vera Aguilar, E; Cebrián, M E

2001-03-23

Industrial growth has created the potential for environmental problems in Mexico, since attention to environmental controls and urban planning has lagged behind the pace of industrialization. The aim of this cross-sectional study was to assess lead exposure in children aged 6-9 yr attending 3 primary schools and living in the vicinity of the largest smelter complex in Mexico. One of the schools is located 650 m distant from a smelter complex that includes a lead smelter (close school); the second is located 1750 m away from the complex and at the side of a heavy traffic road (intermediate school) in Torreon, Coahuila. The third school is located in Comez Palacio, Durango, 8100 m away from the smelter complex and distant from heavy vehicular traffic or industrial areas (remote school). Lead was measured in air, soil, dust, and well water. Lead in blood (PbB) was determined in 394 children attending the above mentioned schools. Determinations were performed by atomic absorption spectrometry. Diet, socioeconomic status, hygienic habits, and other variables were assessed by questionnaire. Median (range) PbB values were 7.8 microg/dl (3.54-29.61) in the remote school, 21.8 microg/dl (8.37-52.08) in the intermediate school and 27.6 microg/dl (7.37-58.53) in children attending the close school. The percentage of children with PbB > 15 microg/dl was 6.80%, 84.9%, and 92.1% respectively. In this order, the geometric means (range) of Pb concentrations in air were 2.5 microg/m3 (1.1-7.5), 5.8 microg/m3 (4.3-8.5), and 6.1 microg/m3 (1.6-14.9). The Pb concentrations in dust from playgrounds areas in the intermediate and close school settings ranged from 1,457 to 4,162.5 mg/kg. Pb concentrations in drinking water were less than 5 microg/L. Soil and dust ingestion and inhalation appear to be the main routes of exposure. Our results indicate that environmental contamination has resulted in an increased body burden of Pb, suggesting that children living in the vicinity of the

Improved dust handling at Inco's Copper Cliff smelter

International Nuclear Information System (INIS)

Dutton, A.; Warner, A.E.M.; Humphris, M.J.

1989-01-01

The Cooper Cliff Smelter Complex comprises three major production departments - a Nickel Smelter for the processing of nickel concentrated to a low iron, nickel - copper sulphide (Bessemer) matte; a Matte Processing plant for the separation of matte sulphides and the production of market nickel oxides and refinery feeds and a Copper Smelter to process copper concentrates to blister copper. Annual production is currently -114,000 tonnes of copper as blister and -110,000 tonnes of nickel. The nickel concentrate (11-13% Ni, 2-3% Cu) is roasted in multi-hearth roasters, smelted in oxy-fuel fired reverberatory furnaces to a 30-35% CuNiCo matte and converted to Bessemer matte (75% CuNiCo) in Peirce-Smith converters. The Bessemer matte is slow cooled and crushed for subsequent separation by mineral dressing techniques in the Matte Processing plant into nickel (sulphide and metallic) concentrates and a copper (chalcocite) concentrate. Nickel sulphides are further processed in fluid bed reactors to oxide market product or refinery feedstock. The copper concentrate (29-30% Cu, 0.9% No.) is dried in fluid bed driers, smelted to a 40-50% copper matte in an Inco oxygen flash furnace and converted to blister copper in Peirce-Smith converters. The chalcocite concentrate from the matte separation stage is flash converted to a semi-blister (3-4% S, 4-5% Ni) and then finished to lighter conventionally. A schematic process flowsheet of the Smelter Complex is shown in this paper

Antimony distribution and environmental mobility at an historic antimony smelter site, New Zealand

International Nuclear Information System (INIS)

Wilson, N.J.; Craw, D.; Hunter, K.

2004-01-01

A historic antimony smelter site at Endeavour Inlet, New Zealand has smelter residues with up to 17 wt.% antimony. Residues include coarse tailings (cm scale particles, poorly sorted), sand tailings (well sorted) and smelter slag (blocks up to 30 cm across). All of this material has oxidised to some degree over the ca. 100 years since the site was abandoned. Oxidation has resulted in acidification of the residues down to pH 2-5. Smelter slag contains pyrrhotite (FeS) and metallic antimony, and oxidation is restricted to surfaces only. The coarse tailings are the most oxidised, and few sulfide grains persist. Unoxidised sand tailings contain 10-20 vol.% stibnite (Sb 2 S 3 ) containing up to 5% As, with subordinate arsenopyrite (FeAsS), and minor pyrite (FeS 2 ). The sand tailings are variably oxidised on a scale of 2-10 cm, but original depositional layering is preserved during oxidation and formation of senarmontite (Sb 2 O 3 ). Oxidation of sand tailings has resulted in localised mobility of both Sb and As on the cm scale, resulting in redistribution of these metalloids with iron oxyhydroxide around sand grain boundaries. Experiments demonstrate that Sb mobility decreases with time on a scale of days. Attenuation of both As and Sb occurs due to adsorption on to iron oxyhydroxides which are formed during oxidation of the smelter residues. There is no detectable loss of Sb or As from the smelter site into the adjacent river, <50 m away, which has elevated Sb (ca. 20 μg/l) and As (ca. 7 μg /l) from mineralised rocks upstream. Despite the high concentrations of Sb and As in the smelter residues, these metalloids are not being released into the environment. - High levels of antimony in primitive smelter soils remain largely immobile on the metre scale

76 FR 64943 - Proposed Cercla Administrative Cost Recovery Settlement; ACM Smelter and Refinery Site, Located...

Science.gov (United States)

2011-10-19

... Settlement; ACM Smelter and Refinery Site, Located in Cascade County, MT AGENCY: Environmental Protection... projected future response costs concerning the ACM Smelter and Refinery NPL Site (Site), Operable Unit 1..., Helena, MT 59626. Mr. Sturn can be reached at (406) 457-5027. Comments should reference the ACM Smelter...

Feasibility study of a portable smelter for scrap metals

International Nuclear Information System (INIS)

Cavendish, J.H.

1976-06-01

The use of a portable smelter to process uranium-contaminated scrap metals was studied. Objectives were to convert scrap metal located at many diverse sites into a form which would be suitable for unlicensed sale and reduce the problems associated with storing the scrap. The Foundry Design Company study indicated the portable smelter concept was feasible from an equipment and transportation standpoint. Capital costs for a 5-ton/hour (steel) nominal capacity unit were estimated to be $2,349,000. Technical evaluation indicates that all the common metals considered, i.e., iron, nickel, copper, and aluminum, are amenable to uranium decontamination by smelting except aluminum. An economic evaluation of the processing of the 30,000 tons of steel scrap to be generated by the Cascade Improvement Program by a portable smelter was made based upon information supplied by Foundry Design Company, plus the assumption that the product metal could be sold for $120.00 per ton. This evaluation indicated a net return of $2,424,000 to the government could be realized. The Health and Safety study indicated no major problems of this nature would be encountered in operating a portable smelter. The legal review indicated the proposed operation fell within the authority of existing regulations. Consideration of possible conflicts with regard to competition with the private sector was suggested

Selecting an oxygen plant for a copper smelter modernization

Science.gov (United States)

Larson, Kenneth H.; Hutchison, Robert L.

1994-10-01

The selection of an oxygen plant for the Cyprus Miami smelter modernization project began with a good definition of the use requirements and the smelter process variables that can affect oxygen demand. To achieve a reliable supply of oxygen with a reasonable amount of capital, critical equipment items were reviewed and reliability was added through the use of installed spares, purchase of insurance spare parts or the installation of equipment design for 50 percent of the production design such that the plant could operate with one unit while the other unit is being maintained. The operating range of the plant was selected to cover variability in smelter oxygen demand, and it was recognized that the broader operating range sacrificed about two to three percent in plant power consumption. Careful consideration of the plant "design point" was important to both the capital and operating costs of the plant, and a design point was specified that allowed a broad range of operation for maximum flexibility.

Finite Element Analysis of Warpage in Laminated Aluminium Alloy Plates for Machining of Primary Aeronautic Parts

International Nuclear Information System (INIS)

Reis, A. C.; Moreira Filho, L. A.; Menezes, M. A.

2007-01-01

The aim of this paper consists in presenting a method of simulating the warpage in 7xxx series aluminium alloy plates. To perform this simulation finite element software MSC.Patran and MSC.Marc were used. Another result of this analysis will be the influence on material residual stresses induced on the raw material during the rolling process upon the warpage of primary aeronautic parts, fabricated through machining (milling) at Embraer. The method used to determinate the aluminium plate residual stress was Layer Removal Test. The numerical algorithm Modified Flavenot Method was used to convert layer removal and beam deflection in stress level. With such information about the level and profile of residual stresses become possible, during the step that anticipate the manufacturing to incorporate these values in the finite-element approach for modelling warpage parts. Based on that warpage parameter surely the products are manufactured with low relative vulnerability propitiating competitiveness and price

Toxicity of dissolved and precipitated aluminium to marine diatoms.

Science.gov (United States)

Gillmore, Megan L; Golding, Lisa A; Angel, Brad M; Adams, Merrin S; Jolley, Dianne F

2016-05-01

Localised aluminium contamination can lead to high concentrations in coastal waters, which have the potential for adverse effects on aquatic organisms. This research investigated the toxicity of 72-h exposures of aluminium to three marine diatoms (Ceratoneis closterium (formerly Nitzschia closterium), Minutocellus polymorphus and Phaeodactylum tricornutum) by measuring population growth rate inhibition and cell membrane damage (SYTOX Green) as endpoints. Toxicity was correlated to the time-averaged concentrations of different aluminium size-fractions, operationally defined as aluminium exposure varied between diatom species. C. closterium was the most sensitive species (10% inhibition of growth rate (72-h IC10) of 80 (55-100)μg Al/L (95% confidence limits)) while M. polymorphus (540 (460-600)μg Al/L) and P. tricornutum (2100 (2000-2200)μg Al/L) were less sensitive (based on measured total aluminium). Dissolved aluminium was the primary contributor to toxicity in C. closterium, while a combination of dissolved and precipitated aluminium forms contributed to toxicity in M. polymorphus. In contrast, aluminium toxicity to the most tolerant diatom P. tricornutum was due predominantly to precipitated aluminium. Preliminary investigations revealed the sensitivity of C. closterium and M. polymorphus to aluminium was influenced by initial cell density with aluminium toxicity significantly (paluminium toxicity to diatoms do not involve compromising the plasma membrane. These results indicate that marine diatoms have a broad range in sensitivity to aluminium with toxic mechanisms related to both dissolved and precipitated aluminium. Copyright © 2016 Elsevier B.V. All rights reserved.

Hydrometallurgical treatment of copper smelter dusts. Desarsenification of leaching solutions

International Nuclear Information System (INIS)

Alguacil, F.J.; Magne, L.; Navarro, P.; Simpson, J.

1996-01-01

Copper smelter dusts contain along with this metal, which is amenable for its recovery, a number of other metals (especially arsenic) which are considered as toxic. Different alternatives have been proposed for the treatment of such metallurgical residues and among them Hydrometallurgy shows good perspectives for its application in this field. In the present work different hydrometallurgical processes proposed for the treatment of copper smelter dusts are described and evaluated together with different alternatives given for the Desarsenification of the leaching solutions. (Author) 36 refs

Speciation of Cr(VI) in environmental samples in the vicinity of the ferrochrome smelter.

Science.gov (United States)

Sedumedi, Hilda N; Mandiwana, Khakhathi L; Ngobeni, Prince; Panichev, Nikolay

2009-12-30

The impact of ferrochrome smelter on the contamination of its environment with toxic hexavalent chromium, Cr(VI), was assessed by analyzing smelter dusts, soil, grass and tree barks. For the separation of Cr(VI) from Cr(III), solid samples were treated with 0.1M Na(2)CO(3) and filtered through hydrophilic PDVF 0.45 microm filter prior to the determination of Cr(VI) by electrothermal atomic absorption spectrometry (ET-AAS). Ferrochrome smelter dust was found to contain significant levels of Cr(VI), viz. 43.5 microg g(-1) (cyclone dust), 2710 microg g(-1) (fine dust), and 7800 microg g(-1) (slimes dust) which exceeded the maximum acceptable risk concentration (20 microg g(-1)). The concentration of Cr(VI) in environmental samples of grass (3.4+/-0.2), soil (7.7+/-0.2), and tree bark (11.8+/-1.2) collected in the vicinity of the chrome smelter were higher as compared with the same kind of samples collected from uncontaminated area. The results of the investigation show that ferrochrome smelter is a source of environmental pollution with contamination factors of Cr(VI) ranging between 10 and 50.

Speciation of Cr(VI) in environmental samples in the vicinity of the ferrochrome smelter

International Nuclear Information System (INIS)

Sedumedi, Hilda N.; Mandiwana, Khakhathi L.; Ngobeni, Prince; Panichev, Nikolay

2009-01-01

The impact of ferrochrome smelter on the contamination of its environment with toxic hexavalent chromium, Cr(VI), was assessed by analyzing smelter dusts, soil, grass and tree barks. For the separation of Cr(VI) from Cr(III), solid samples were treated with 0.1 M Na 2 CO 3 and filtered through hydrophilic PDVF 0.45 μm filter prior to the determination of Cr(VI) by electrothermal atomic absorption spectrometry (ET-AAS). Ferrochrome smelter dust was found to contain significant levels of Cr(VI), viz. 43.5 μg g -1 (cyclone dust), 2710 μg g -1 (fine dust), and 7800 μg g -1 (slimes dust) which exceeded the maximum acceptable risk concentration (20 μg g -1 ). The concentration of Cr(VI) in environmental samples of grass (3.4 ± 0.2), soil (7.7 ± 0.2), and tree bark (11.8 ± 1.2) collected in the vicinity of the chrome smelter were higher as compared with the same kind of samples collected from uncontaminated area. The results of the investigation show that ferrochrome smelter is a source of environmental pollution with contamination factors of Cr(VI) ranging between 10 and 50.

Sulfur dioxide emissions from Peruvian copper smelters detected by the ozone monitoring instrument

NARCIS (Netherlands)

Carn, S.A.; Krueger, A.J.; Krotkov, N.A.; Yang, Kai; Levelt, P.F.

2007-01-01

We report the first daily observations of sulfur dioxide (SO2) emissions from copper smelters by a satellite-borne sensor - the Ozone Monitoring Instrument (OMI) on NASA's EOS/Aura spacecraft. Emissions from two Peruvian smelters (La Oroya and Ilo) were detected in up to 80% of OMI overpasses

Recent developments in advanced aircraft aluminium alloys

International Nuclear Information System (INIS)

Dursun, Tolga; Soutis, Costas

2014-01-01

Highlights: • To compete with composites, performance of aluminium alloys should be increased. • Al–Li alloys have higher strength, fracture and fatigue/corrosion resistance. • Improvements of aerospace Al alloys are due to optimised solute content and ratios. • In selecting new materials, there should be no reduction in the level of safety. • The use of hybrid materials could provide additional opportunities for Al alloys. - Abstract: Aluminium alloys have been the primary material for the structural parts of aircraft for more than 80 years because of their well known performance, well established design methods, manufacturing and reliable inspection techniques. Nearly for a decade composites have started to be used more widely in large commercial jet airliners for the fuselage, wing as well as other structural components in place of aluminium alloys due their high specific properties, reduced weight, fatigue performance and corrosion resistance. Although the increased use of composite materials reduced the role of aluminium up to some extent, high strength aluminium alloys remain important in airframe construction. Aluminium is a relatively low cost, light weight metal that can be heat treated and loaded to relatively high level of stresses, and it is one of the most easily produced of the high performance materials, which results in lower manufacturing and maintenance costs. There have been important recent advances in aluminium aircraft alloys that can effectively compete with modern composite materials. This study covers latest developments in enhanced mechanical properties of aluminium alloys, and high performance joining techniques. The mechanical properties on newly developed 2000, 7000 series aluminium alloys and new generation Al–Li alloys are compared with the traditional aluminium alloys. The advantages and disadvantages of the joining methods, laser beam welding and friction stir welding, are also discussed

EMERGING TECHNOLOGY BULLETIN: RECLAMATION OF LEAD FROM SUPERFUND WASTE MATERIAL USING SECONDARY LEAD SMELTERS

Science.gov (United States)

This process involves incorporating lead-contaminated Superfund waste with the regular feed to a secondary lead smelter. Since secondary lead smelters already recover lead from recycled automobile batteries, it seems likely that this technology could be used to treat waste from ...

Composition and fate of mine- and smelter-derived particles in soils of humid subtropical and hot semi-arid areas

Energy Technology Data Exchange (ETDEWEB)

Ettler, Vojtěch, E-mail: ettler@natur.cuni.cz [Institute of Geochemistry, Mineralogy and Mineral Resources, Faculty of Science, Charles University in Prague, Albertov 6, 128 43 Praha 2 (Czech Republic); Johan, Zdenek [BRGM, Avenue Claude Guillemin, 45082 Orléans Cedex 2 (France); Kříbek, Bohdan; Veselovský, František [Czech Geological Survey, Geologická 6, 152 00 Praha 5 (Czech Republic); Mihaljevič, Martin [Institute of Geochemistry, Mineralogy and Mineral Resources, Faculty of Science, Charles University in Prague, Albertov 6, 128 43 Praha 2 (Czech Republic); Vaněk, Aleš; Penížek, Vít [Department of Soil Science and Soil Protection, Faculty of Agrobiology, Food and Natural Resources, Czech University of Life Sciences Prague, Kamýcká 129, 165 21 Praha 6 (Czech Republic); Majer, Vladimír [Czech Geological Survey, Geologická 6, 152 00 Praha 5 (Czech Republic); Sracek, Ondra [Department of Geology, Faculty of Science, Palacký University in Olomouc, 17. listopadu 12, 771 46 Olomouc (Czech Republic); Mapani, Ben; Kamona, Fred [Department of Geology, Faculty of Science, University of Namibia, Private Bag 13301, Windhoek (Namibia); Nyambe, Imasiku [University of Zambia, School of Mines, P. O. Box 32 379, Lusaka (Zambia)

2016-09-01

�� Soluble sulphates and arsenolite from primary smelter dusts not detected in soils • Higher metal availability and greater weathering of particles in subtropical soils • Complex Ca–Cu–Pb arsenates efficiently control mobility of metal(loids).

Some effects of smelter pollution northeast of Falconbridge, Ontario

Energy Technology Data Exchange (ETDEWEB)

Gorham, E

1960-01-01

A study along a line northwest from the metal smelter at Falconbridge, Ontario, reveals that strong sulphate accumulation in the surface soil occurs only within about one mile of the chimneys emitting sulphur dioxide pollution while effects upon the soil drainage waters are marked to a distance of nearly two miles, and still clearly evident 10 or more miles away. The number of species present in the flora declines sharply within about four miles of the smelter, but certain species (e.g. Pinus strobus, Vaccinium myrtilloides) disappear at much greater distances. Among the most tolerant species are Acer rubrum, Quercus rubra, Sambucus pubens, and Polygonum cilinode.

Lead identification in soil surrounding a used lead acid battery smelter area in Banten, Indonesia

International Nuclear Information System (INIS)

Adventini, N; Santoso, M; Lestiani, D D; Syahfitri, W Y N; Rixson, L

2017-01-01

A used lead acid battery smelter generates particulates containing lead that can contaminate the surrounding environment area. Lead is a heavy metal which is harmful to health if it enters the human body through soil, air, or water. An identification of lead in soil samples surrounding formal and informal used lead acid battery smelters area in Banten, Indonesia using EDXRF has been carried out. The EDXRF accuracy and precision evaluated from marine sediment IAEA 457 gave a good agreement to the certified value. A number of 16 soil samples from formal and informal areas and 2 soil samples from control area were taken from surface and subsurface soils. The highest lead concentrations from both lead smelter were approximately 9 folds and 11 folds higher than the reference and control samples. The assessment of lead contamination in soils described in C f index was in category: moderately and strongly polluted by lead for formal and informal lead smelter. Daily lead intake of children in this study from all sites had exceeded the recommended dietary allowance. The HI values for adults and children living near both lead smelter areas were greater than the value of safety threshold 1. This study finding confirmed that there is a potential health risk for inhabitants surrounding the used lead acid battery smelter areas in Banten, Indonesia. (paper)

Aluminium bridges, aluminium bridge decks

NARCIS (Netherlands)

Soetens, F.; Straalen, IJ.J. van

2003-01-01

Applications of aluminium have grown considerably in building and civil engineering the last decade. In building and civil engineering the increase of aluminium applications is due to various aspects like light weight, durability and maintenance, use of extrusions, and esthetics. The paper starts

Speciation of Cr(VI) in environmental samples in the vicinity of the ferrochrome smelter

Energy Technology Data Exchange (ETDEWEB)

Sedumedi, Hilda N. [Department of Chemistry, Tshwane University of Technology, P.O. Box 56208, Arcadia, 0007, Pretoria (South Africa); Mandiwana, Khakhathi L., E-mail: MandiwanaKL@tut.ac.za [Department of Chemistry, Tshwane University of Technology, P.O. Box 56208, Arcadia, 0007, Pretoria (South Africa); Ngobeni, Prince; Panichev, Nikolay [Department of Chemistry, Tshwane University of Technology, P.O. Box 56208, Arcadia, 0007, Pretoria (South Africa)

2009-12-30

The impact of ferrochrome smelter on the contamination of its environment with toxic hexavalent chromium, Cr(VI), was assessed by analyzing smelter dusts, soil, grass and tree barks. For the separation of Cr(VI) from Cr(III), solid samples were treated with 0.1 M Na{sub 2}CO{sub 3} and filtered through hydrophilic PDVF 0.45 {mu}m filter prior to the determination of Cr(VI) by electrothermal atomic absorption spectrometry (ET-AAS). Ferrochrome smelter dust was found to contain significant levels of Cr(VI), viz. 43.5 {mu}g g{sup -1} (cyclone dust), 2710 {mu}g g{sup -1} (fine dust), and 7800 {mu}g g{sup -1} (slimes dust) which exceeded the maximum acceptable risk concentration (20 {mu}g g{sup -1}). The concentration of Cr(VI) in environmental samples of grass (3.4 {+-} 0.2), soil (7.7 {+-} 0.2), and tree bark (11.8 {+-} 1.2) collected in the vicinity of the chrome smelter were higher as compared with the same kind of samples collected from uncontaminated area. The results of the investigation show that ferrochrome smelter is a source of environmental pollution with contamination factors of Cr(VI) ranging between 10 and 50.

Characterization of the lead smelter slag in Santo Amaro, Bahia, Brazil

International Nuclear Information System (INIS)

Andrade Lima, L.R.P. de; Bernardez, L.A.

2011-01-01

For 33 years, a primary lead smelter operated in Santo Amaro (Brazil). Since the 1970s, large amounts of Pb and Cd have been widely documented in the blood and hair of people living near the smelter. The plant closed down in 1993, and several years later, the Pb levels in the blood of children under 4 years of age living near the smelter were high, where the disposed lead slag was suspected to be the main source of this contamination. The objective of this study is to elucidate the source of the Pb contamination and any other potentially toxic contamination, focusing on the characterization of the slag. The samples used for this characterization study were taken from the slag heaps. The results of the chemical analysis showed that the major constituents of the slag, in decreasing order of wt%, were the following: Fe 2 O 3 (28.10), CaO (23.11), SiO 2 (21.39), ZnO (9.47), MgO (5.44), PbO (4.06), Al 2 O 3 (3.56), C (2.26), MnO (1.44), Na 2 O (0.27), S (0.37), K 2 O (0.26), and TiO 2 (0.25). The Cd content of the slag was 57.3 mg/kg, which is relatively low. The X-ray diffraction and the electron probe microanalyzer X-ray mapping indicated that the major phases in the slag were wuestite, olivine, kirschsteinite, and franklinite. Only spheroidal metallic Pb was found in the slag. The leaching study showed that the slag was stable at a pH greater than 2.8, and only in an extremely acidic environment was the solubilization of the Pb enhanced significantly. The solubilization of Zn was very limited in the acidic and alkaline environments. These results can be explained by the limited leachability of the metallic Pb and Zn-bearing compounds. The leaching study used TCLP, SPLP, and SWEP and indicated that the lead slag was stable in weak acidic environments for short contact times.

Alloys of uranium and aluminium with low aluminium content; Alliages uranium-aluminium a faible teneur en aluminium

Energy Technology Data Exchange (ETDEWEB)

Cabane, G; Englander, M; Lehmann, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1955-07-01

Uranium, as obtained after spinning in phase {gamma}, presents an heterogeneous structure with large size grains. The anisotropic structure of the metal leads to an important buckling and surface distortion of the fuel slug which is incompatible with its tubular cladding for nuclear fuel uses. Different treatments have been made to obtain an isotropic structure presenting high thermal stability (laminating, hammering and spinning in phase {alpha}) without success. Alloys of uranium and aluminium with low aluminium content present important advantage in respect of non allied uranium. The introduction of aluminium in the form of intermetallic compound (UAl{sub 2}) gives a better resistance to thermal fatigue. Alloys obtained from raw casting present an improved buckling and surface distortion in respect of pure uranium. This improvement is obtained with uranium containing between 0,15 and 0,5 % of aluminium. An even more improvement in thermal stability is obtained by thermal treatments of these alloys. These new characteristics are explained by the fine dispersion of the UAl{sub 2} particles in uranium. The results after treatments obtained from an alloy slug containing 0,4 % of aluminium show no buckling or surface distortion and no elongation. (M.P.)

Rows of Dislocation Loops in Aluminium Irradiated by Aluminium Ions

DEFF Research Database (Denmark)

Henriksen, L.; Johansen, A.; Koch, J.

1967-01-01

Single-crystal aluminium specimens, irradiated with 50-keV aluminium ions, contain dislocation loops that are arranged in regular rows along <110 > directions. ©1967 The American Institute of Physics......Single-crystal aluminium specimens, irradiated with 50-keV aluminium ions, contain dislocation loops that are arranged in regular rows along directions. ©1967 The American Institute of Physics...

All cause mortality and incidence of cancer in workers in bauxite mines and alumina refineries

NARCIS (Netherlands)

Fritschi, Lin; Hoving, Jan Lucas; Sim, Malcolm R.; del Monaco, Anthony; Macfarlane, Ewan; McKenzie, Dean; Benke, Geza; de Klerk, Nicholas

2008-01-01

Bauxite is a reddish clay that is refined to produce alumina, which is then reduced to aluminium. There have been studies examining the health of workers in aluminium smelters, but not workers in bauxite mining and alumina refining. A cohort of employees of 1 large aluminium company since 1983 was

Socio-demographic characteristics of traditional gold smelters in Makassar, south Sulawesi, Indonesia

Science.gov (United States)

Habo Abbas, Hasriwiani; Sakakibara, Masayuki; Hakim Arma, Lukmanul; Hardi Yanti, Iva

2017-06-01

The traditional gold smelting in Makassar, South Sulawesi, Indonesia, is an informal work with the manufacture of gold jewelry as the core activity. Stages of the gold processing include panning, smelting, and refining with mercury. In the current study, we used a social demography analysis to classify the traditional gold smelter workers in this region. Data (e.g. sex, age, education level, time working, and income) were obtained from a questionnaire survey of 58 smelter workers in the Wajo and Tallo Sub-districts of Makassar. Results showed that 84.5% of the workers were males aged from 21 to 50 years with on the average 15 year of work. The gold smelter were last educated in elementary school (31.0%), junior high school (36.2%), and senior high school (27.6%) levels whereas 5.1% have no education. We found that the monthly income of an un-skilled worker was ∼Rp. 2 million (USD 147.0) whereas that of a skilled worker was between Rp. 2.5 million (USD 183.76) and Rp. 5 million (USD 367.51). An owner could earn over Rp. 5 million (USD 367.51) per month. The result suggested that the traditional gold smelting used rudimentary technique and attracted young people with a low education level. This business continues to exist because the worker earn sufficient income and may higher through mastering gold smelter proficiency.

Heavy metals in the atmosphere coming from a copper smelter in Chile

Science.gov (United States)

Romo-Kröger, C. M.; Morales, J. R.; Dinator, M. I.; Llona, F.; Eaton, L. C.

The Chilean mine El Teniente is the world's largest underground copper mine. It operates a giant smelter at Caletones (34° 7' S, 70° 27' W) and we have found it is the major source of air contamination in the region. In August 1991 a special circumstance occurred due to a labor strike, with total cessation of activities. A time series analysis of airborne particles collected at a site about 13 km from the smelter was performed in a period including the strike. The PIXE method and other techniques were used to analyse fine (Elemental characterization of soil samples by radioactive source analysis demonstrated that this group of elements did not come from airborne soil dust. Cluster analyses of the interelement correlation matrices, resulting from PIXE data, showed one group (Si, K, Ca, Fe) with main origin in soil and another group (S, Cu, Zn, As) coming from the copper smelter.

Effective radium concentration in topsoils contaminated by lead and zinc smelters

Energy Technology Data Exchange (ETDEWEB)

Girault, Frédéric, E-mail: girault@ipgp.fr [Institut de Physique du Globe de Paris, Sorbonne Paris Cité, Université Paris Diderot, CNRS, Paris, France. (France); Perrier, Frédéric; Poitou, Charles; Isambert, Aude [Institut de Physique du Globe de Paris, Sorbonne Paris Cité, Université Paris Diderot, CNRS, Paris, France. (France); Théveniaut, Hervé; Laperche, Valérie [Bureau de Recherches Géologiques et Minières, Orléans, France. (France); Clozel-Leloup, Blandine [Bureau de Recherches Géologiques et Minières, Villeurbanne, France. (France); Douay, Francis [Laboratoire Génie Civil et géo Environnement, ISA Lille, Lille, France. (France)

2016-10-01

Trace elements (TE) are indicative of industrial pollution in soils, but geochemical methods are difficult to implement in contaminated sites with large numbers of samples. Therefore, measurement of soil magnetic susceptibility (MS) has been used to map TE pollutions, albeit with contrasted results in some cases. Effective radium concentration (EC{sub Ra}), product of radium concentration by the emanation factor, can be measured in a cost-effective manner in the laboratory, and could then provide a useful addition. We evaluate this possibility using 186 topsoils sampled over about 783 km{sup 2} around two former lead and zinc smelters in Northern France. The EC{sub Ra} values, obtained from 319 measurements, range from 0.70 ± 0.06 to 12.53 ± 0.49 Bq·kg{sup −1}, and are remarkably organized spatially, away from the smelters, in domains corresponding to geographical units. Lead-contaminated soils, with lead concentrations above 100 mg·kg{sup −1} < 3 km from the smelters, are characterized on average by larger peak EC{sub Ra} values and larger dispersion. At large scales, away from the smelters, spatial variations of EC{sub Ra} correlate well with spatial variations of MS, thus suggesting that, at distance larger than 5 km, variability of MS contains a significant natural component. Larger EC{sub Ra} values are correlated with larger fine fraction and, possibly, mercury concentration. While MS is enhanced in the vicinity of the smelters and is associated with the presence of soft ferrimagnetic minerals such as magnetite, it does not correlate systematically with metal concentrations. When multiple industrial and urban sources are present, EC{sub Ra} mapping, thus, can help in identifying at least part of the natural spatial variability of MS. More generally, this study shows that EC{sub Ra} mapping provides an independent and reliable assessment of the background spatial structure which underlies the structure of a given contamination. Furthermore, EC{sub Ra

Effective radium concentration in topsoils contaminated by lead and zinc smelters

International Nuclear Information System (INIS)

Girault, Frédéric; Perrier, Frédéric; Poitou, Charles; Isambert, Aude; Théveniaut, Hervé; Laperche, Valérie; Clozel-Leloup, Blandine; Douay, Francis

2016-01-01

Trace elements (TE) are indicative of industrial pollution in soils, but geochemical methods are difficult to implement in contaminated sites with large numbers of samples. Therefore, measurement of soil magnetic susceptibility (MS) has been used to map TE pollutions, albeit with contrasted results in some cases. Effective radium concentration (EC_R_a), product of radium concentration by the emanation factor, can be measured in a cost-effective manner in the laboratory, and could then provide a useful addition. We evaluate this possibility using 186 topsoils sampled over about 783 km"2 around two former lead and zinc smelters in Northern France. The EC_R_a values, obtained from 319 measurements, range from 0.70 ± 0.06 to 12.53 ± 0.49 Bq·kg"−"1, and are remarkably organized spatially, away from the smelters, in domains corresponding to geographical units. Lead-contaminated soils, with lead concentrations above 100 mg·kg"−"1 < 3 km from the smelters, are characterized on average by larger peak EC_R_a values and larger dispersion. At large scales, away from the smelters, spatial variations of EC_R_a correlate well with spatial variations of MS, thus suggesting that, at distance larger than 5 km, variability of MS contains a significant natural component. Larger EC_R_a values are correlated with larger fine fraction and, possibly, mercury concentration. While MS is enhanced in the vicinity of the smelters and is associated with the presence of soft ferrimagnetic minerals such as magnetite, it does not correlate systematically with metal concentrations. When multiple industrial and urban sources are present, EC_R_a mapping, thus, can help in identifying at least part of the natural spatial variability of MS. More generally, this study shows that EC_R_a mapping provides an independent and reliable assessment of the background spatial structure which underlies the structure of a given contamination. Furthermore, EC_R_a may provide a novel index to identify soils

Characterization of the lead smelter slag in Santo Amaro, Bahia, Brazil

Energy Technology Data Exchange (ETDEWEB)

Andrade Lima, L.R.P. de, E-mail: lelo@ufba.br [Department of Materials Science and Technology, Federal University of Bahia, C.P. 6974, Salvador, BA 41810-971 (Brazil); Bernardez, L.A. [Ingenium Consultoria em Engenharia Ltda (Brazil)

2011-05-30

For 33 years, a primary lead smelter operated in Santo Amaro (Brazil). Since the 1970s, large amounts of Pb and Cd have been widely documented in the blood and hair of people living near the smelter. The plant closed down in 1993, and several years later, the Pb levels in the blood of children under 4 years of age living near the smelter were high, where the disposed lead slag was suspected to be the main source of this contamination. The objective of this study is to elucidate the source of the Pb contamination and any other potentially toxic contamination, focusing on the characterization of the slag. The samples used for this characterization study were taken from the slag heaps. The results of the chemical analysis showed that the major constituents of the slag, in decreasing order of wt%, were the following: Fe{sub 2}O{sub 3} (28.10), CaO (23.11), SiO{sub 2} (21.39), ZnO (9.47), MgO (5.44), PbO (4.06), Al{sub 2}O{sub 3} (3.56), C (2.26), MnO (1.44), Na{sub 2}O (0.27), S (0.37), K{sub 2}O (0.26), and TiO{sub 2} (0.25). The Cd content of the slag was 57.3 mg/kg, which is relatively low. The X-ray diffraction and the electron probe microanalyzer X-ray mapping indicated that the major phases in the slag were wuestite, olivine, kirschsteinite, and franklinite. Only spheroidal metallic Pb was found in the slag. The leaching study showed that the slag was stable at a pH greater than 2.8, and only in an extremely acidic environment was the solubilization of the Pb enhanced significantly. The solubilization of Zn was very limited in the acidic and alkaline environments. These results can be explained by the limited leachability of the metallic Pb and Zn-bearing compounds. The leaching study used TCLP, SPLP, and SWEP and indicated that the lead slag was stable in weak acidic environments for short contact times.

Aluminium in human sweat.

Science.gov (United States)

Minshall, Clare; Nadal, Jodie; Exley, Christopher

2014-01-01

It is of burgeoning importance that the human body burden of aluminium is understood and is measured. There are surprisingly few data to describe human excretion of systemic aluminium and almost no reliable data which relate to aluminium in sweat. We have measured the aluminium content of sweat in 20 healthy volunteers following mild exercise. The concentration of aluminium ranged from 329 to 5329μg/L. These data equate to a daily excretion of between 234 and 7192μg aluminium and they strongly suggest that perspiration is the major route of excretion of systemic aluminium in humans. Copyright © 2013 Elsevier GmbH. All rights reserved.

The mineralogy of bauxite for producing smelter-grade alumina

Science.gov (United States)

Authier-Martin, M.; Forte, G.; Ostap, S.; See, J.

2001-12-01

Aluminum-producing companies rely on low-cost, high-purity, smelter-grade alumina (aluminum oxide), and alumina production utilizes the bulk of bauxites mined world-wide. The mineralogy of the bauxites has a significant impact on the operation of the Bayer process for alumina production. Typically, the Bayer process produces smelter-grade alumina of 99.5% Al2O3, starting from bauxite containing 30% to 60% Al2O3. The main objective of the Bayer process is to extract the maximum amount of aluminum from the bauxite at as high an aluminate concentration in solution as possible, while limiting any troublesome side reactions. Only with a better understanding of the chemistry of the mineral species and a strict control of the operating/processing conditions can the Bayer process produce efficiently, a low cost, high-quality alumina with minimum detrimental environmental impact.

Mercury contamination in vicinity of secondary copper smelters in Fuyang, Zhejiang Province, China: Levels and contamination in topsoils

International Nuclear Information System (INIS)

Yin Xuebin; Yao Chunxia; Song Jing; Li Zhibo; Zhang Changbo; Qian Wei; Bi De; Li Chenxi; Teng Ying; Wu Longhua; Wan Hongdong; Luo Yongming

2009-01-01

In the present study, we aim to investigate the extent of soil contamination by Hg, particularly by anthropogenic Hg, and tentatively estimate the total Hg (Hg T ) accumulation in topsoils (0-15 cm) in Fuyang, Zhejiang Province-a secondary Cu smelter of China. The results show that the levels of soil Hg in the vicinity of the smelters have been substantially elevated following local smelting activities. The spatial distribution of soil Hg in this area reveals a rapid decrease as the distance from the smelter reaches 1.5 km, which is probably due to the quick deposition process of particulate Hg and reactive gaseous Hg emitted from the smelters. The total accumulation of Hg T in the topsoils of the study area of 10.9 km 2 is approximately 365-561 kg and of which 346-543 kg might be contributed by anthropogenic emission alone with an annual emission of 17.3-27.2 kg Hg to the topsoils. - Secondary copper smelters in Fuyang release a considerable amount of mercury into topsoils.

Human exposure to aluminium.

Science.gov (United States)

Exley, Christopher

2013-10-01

Human activities have circumvented the efficient geochemical cycling of aluminium within the lithosphere and therewith opened a door, which was previously only ajar, onto the biotic cycle to instigate and promote the accumulation of aluminium in biota and especially humans. Neither these relatively recent activities nor the entry of aluminium into the living cycle are showing any signs of abating and it is thus now imperative that we understand as fully as possible how humans are exposed to aluminium and the future consequences of a burgeoning exposure and body burden. The aluminium age is upon us and there is now an urgent need to understand how to live safely and effectively with aluminium.

Bio-processing of copper from combined smelter dust and flotation concentrate: A comparative study on the stirred tank and airlift reactors

Energy Technology Data Exchange (ETDEWEB)

Vakylabad, Ali Behrad, E-mail: alibehzad86@yahoo.co.uk [Department of Mining Engineering, Shahid Bahonar University, Kerman (Iran, Islamic Republic of); Engineers of Nano and Bio Advanced Sciences Company (ENBASCo.), ATIC, Mohaghegh University (Iran, Islamic Republic of); Schaffie, Mahin [Department of Chemical Engineering, Shahid Bahonar University of Kerman, Kerman (Iran, Islamic Republic of); Mineral Industries Research Centre (MIRC), Shahid Bahonar University of Kerman, Kerman (Iran, Islamic Republic of); Ranjbar, Mohammad [Department of Mining Engineering, Shahid Bahonar University, Kerman (Iran, Islamic Republic of); Mineral Industries Research Centre (MIRC), Shahid Bahonar University of Kerman, Kerman (Iran, Islamic Republic of); Manafi, Zahra [Sarcheshmeh Copper Complex, National Iranian Copper Industry Company (Iran, Islamic Republic of); Darezereshki, Esmaeel [Mineral Industries Research Centre (MIRC), Shahid Bahonar University of Kerman, Kerman (Iran, Islamic Republic of); Energy and Environmental Engineering Research Center (EERC), Shahid Bahonar University of Kerman, Kerman (Iran, Islamic Republic of)

2012-11-30

Highlights: Black-Right-Pointing-Pointer Flotation concentrate and smelter dust were sampled and combined. Black-Right-Pointing-Pointer Copper bioleaching from the combined was investigated. Black-Right-Pointing-Pointer Two bio-reactors were investigated and optimized: stirred and airlift. Black-Right-Pointing-Pointer STRs had better technical conditions and situations for bacterial leaching. - Abstract: To scrutinize the influence of the design and type of the bioreactors on the bioleaching efficiency, the bioleaching were evaluated in a batch airlift and a batch stirred tank bioreactors with mixed mesophilic and mixed moderately thermophilic bacteria. According to the results, maximum copper recoveries were achieved using the cultures in the stirred tank bioreactors. It is worth noting that the main phase of the flotation concentrate was chalcopyrite (as a primary sulphide), but the smelter dust mainly contained secondary copper sulphides such as Cu{sub 2}S, CuS, and Cu{sub 5}FeS{sub 4}.Under optimum conditions, copper dissolution from the combined flotation concentrate and smelter dust (as an environmental hazard) reached 94.50% in the STR, and 88.02% in the airlift reactor with moderately thermophilic, after 23 days. Also, copper extractions calculated for the bioleaching using mesophilic bacteria were 48.73% and 37.19% in the STR (stirred tank reactor) and the airlift bioreactor, respectively. In addition, the SEM/EDS, XRD, chemical, and mineralogical analyses and studies confirmed the above results.

Bio-processing of copper from combined smelter dust and flotation concentrate: A comparative study on the stirred tank and airlift reactors

International Nuclear Information System (INIS)

Vakylabad, Ali Behrad; Schaffie, Mahin; Ranjbar, Mohammad; Manafi, Zahra; Darezereshki, Esmaeel

2012-01-01

Highlights: ► Flotation concentrate and smelter dust were sampled and combined. ► Copper bioleaching from the combined was investigated. ► Two bio-reactors were investigated and optimized: stirred and airlift. ► STRs had better technical conditions and situations for bacterial leaching. - Abstract: To scrutinize the influence of the design and type of the bioreactors on the bioleaching efficiency, the bioleaching were evaluated in a batch airlift and a batch stirred tank bioreactors with mixed mesophilic and mixed moderately thermophilic bacteria. According to the results, maximum copper recoveries were achieved using the cultures in the stirred tank bioreactors. It is worth noting that the main phase of the flotation concentrate was chalcopyrite (as a primary sulphide), but the smelter dust mainly contained secondary copper sulphides such as Cu 2 S, CuS, and Cu 5 FeS 4 .Under optimum conditions, copper dissolution from the combined flotation concentrate and smelter dust (as an environmental hazard) reached 94.50% in the STR, and 88.02% in the airlift reactor with moderately thermophilic, after 23 days. Also, copper extractions calculated for the bioleaching using mesophilic bacteria were 48.73% and 37.19% in the STR (stirred tank reactor) and the airlift bioreactor, respectively. In addition, the SEM/EDS, XRD, chemical, and mineralogical analyses and studies confirmed the above results.

Determination of Aluminium Content in Aluminium Hydroxide Formulation by FT-NIR Transmittance Spectroscopy

DEFF Research Database (Denmark)

Lai, Xuxin; Zheng, Yiwu; Søndergaard, Ib

2007-01-01

A method for determining the aluminium content of an aluminium hydroxide suspension using near infrared (NIR) transmittance spectroscopy has been developed. Inductively coupled plasma-atomic emission spectroscopy (ICP-AES) was used as reference method. The factors influencing the NIR analysis...... aluminium content in aluminium hydroxide suspension. (c) 2007 Elsevier Ltd. All rights reserved....

Void formation in pure aluminium irradiated with high-energetic electron beams and gamma-quanta

DEFF Research Database (Denmark)

Gan, V. V.; Ozhigou, L. S.; Yamnitsky, V. A.

1983-01-01

The spatial distribution of displaced atoms and helium atoms and also the spectra of damaging energies of primary displaced atoms in a thick aluminium target irradiated with electrons of 225 MeV energy were calculated. Pure aluminium (99.9999%) irradiated up to 0.04 dose was studied by electron...

Effect of Bio char on Plant Growth and Aluminium Form of Soil under Aluminium Stress

Science.gov (United States)

Qian, Lianwen; Li, Qingbiao; Sun, Jingwei; Feng, Ying

2018-01-01

Aluminium-enriched acid red soils in South China easily cause aluminium toxicity to plants, but biochip can improve soils and eliminate soil contaminations. In this project, biochip was used in potted plant control test to study the effect of biochip on plant growth in soil under acid aluminium stress and the migration and conversion of aluminium in plant-soil system. The fin dings show that the application of biochip increases the pH value of soil under aluminium stress significantly, changes the existing form of aluminium ion in soil, reduces the plants’ absorption of aluminium, and alleviates the aluminium toxicity to plants, but too much biochip may inhibit the growth of plants. In this case, further study should be carried out as regards the volume and way of biochip input in practical applications as well as the timeliness of aluminium toxicity removal.

Molecular breeding of cereals for aluminium resistance

Science.gov (United States)

Aluminium (Al3+) toxicity is the primary factor limiting crop production on acidic soils worldwide. In addition to an application of lime for soil amelioration, Al3+ resistant plant varieties have been deployed to raise productivity on such hostile soils. This has been possible due to the exploita...

Confined recrystallization of high-purity aluminium during accumulative roll bonding of aluminium laminates

International Nuclear Information System (INIS)

Chekhonin, Paul; Beausir, Benoît; Scharnweber, Juliane; Oertel, Carl-Georg; Hausöl, Tina; Höppel, Heinz Werner; Brokmeier, Heinz-Günter; Skrotzki, Werner

2012-01-01

Aluminium laminates consisting of high-purity aluminium and commercially pure aluminium have been produced by accumulative roll bonding (ARB) at ambient temperature for up to 10 cycles. To study the microstructure and texture development of the high-purity aluminium layers with regard to the shrinking layer thickness during ARB, microstructure and texture investigations were carried out by electron backscatter diffraction and neutron and X-ray diffraction, respectively. While the commercially pure aluminium layers develop an ultrafine-grained microstructure, partial discontinuous recrystallization occurs in the high-purity layers. The texture of the high-purity layers mainly consists of Cube and “Tilted Cube” (tilted with respect to the transverse direction) components. The experimental results are discussed with respect to confined recrystallization in the ARB aluminium laminates.

Alloys of uranium and aluminium with low aluminium content

International Nuclear Information System (INIS)

Cabane, G.; Englander, M.; Lehmann, J.

1955-01-01

Uranium, as obtained after spinning in phase γ, presents an heterogeneous structure with large size grains. The anisotropic structure of the metal leads to an important buckling and surface distortion of the fuel slug which is incompatible with its tubular cladding for nuclear fuel uses. Different treatments have been made to obtain an isotropic structure presenting high thermal stability (laminating, hammering and spinning in phase α) without success. Alloys of uranium and aluminium with low aluminium content present important advantage in respect of non allied uranium. The introduction of aluminium in the form of intermetallic compound (UAl 2 ) gives a better resistance to thermal fatigue. Alloys obtained from raw casting present an improved buckling and surface distortion in respect of pure uranium. This improvement is obtained with uranium containing between 0,15 and 0,5 % of aluminium. An even more improvement in thermal stability is obtained by thermal treatments of these alloys. These new characteristics are explained by the fine dispersion of the UAl 2 particles in uranium. The results after treatments obtained from an alloy slug containing 0,4 % of aluminium show no buckling or surface distortion and no elongation. (M.P.)

Catchment liming creates recolonization opportunity for sensitive invertebrates in a smelter impacted landscape

Directory of Open Access Journals (Sweden)

John M. Gunn

2016-04-01

Full Text Available The response of a sensitive indicator species to the effects of catchment liming was assessed in a lake severely impacted by atmospheric emissions from a metal smelter in Sudbury, Canada. The lake chemistry recovered following the closure of the local smelter and major reductions (approximately 95% in acid and metal emissions from other area smelters, leading to recolonization of the lake with fish and other biota. However, the littoral macrobenthos community remain severely impoverished. The catchment liming sustained improved stream water quality for 20 years after the initial aerial treatment and created a littoral zone hot spot for the recolonization of Hyalella azteca. Colonization at delta sites of untreated catchment drainage areas, in the same lake, were low and highly variable, and these sites appeared to be impacted from soil erosion and episodic release of acid and metals. This study demonstrated the need to both reduce air pollutants and to conduct land reclamation in severely damaged watersheds, before lake ecosystems themselves can be fully recovered.

Phase transformation of aluminium hydroxide to aα- alumina prepared from different aluminium salts

International Nuclear Information System (INIS)

Masliana Muslimin; Meor Yusoff Meor Sulaiman

2006-01-01

The study intends to look at the most suitable aluminium salt to produce a single-phase a-alumina by the hydrothermal method. In the process to produce alumina from the calcination of aluminium hydroxide (Al(OH) 3 ), three different aluminium salts namely aluminium sulfate (Al 2 (SO 4) 2), aluminium nitrate (A(NO 3 ) 3 ) and aluminium chloride (AlCl 3 ) were tried. The process involved the used of NH 4 OH as the precipitating medium. Aluminium hydroxide produced from each of these salts were characterised by x-ray diffraction (XRD) technique to identity the crystalline phase. Aluminium hydroxide produced by all the different aluminium salts is present as boehmite or pseudo-boehmite phase. Aluminium hydroxide produced from Al 2 (SO) 2 , Al(NO) 3 and AlCl 3 shows the transformation of the boehmite phase to a α-alumina phase at 500 0 C. On further heating, the α-alumina continuously formed at 800 o C followed soon at 1000 o C. But for the Al(NO3) 3 salts a different phase transitions occurs on heating especially at 1000 o C. Here it was observed not a single alumina phase is presence but the presence of both α and γ--alumina phases. At 1300 o C, the single α-alumina phase was formed. The study concluded that aluminium sulphate is recommended in order to obtain a single-phase α-alumina with the required characteristics. (Author)

Effect of iron and silicon in aluminium and its alloys

International Nuclear Information System (INIS)

Kovacs, I.

1990-01-01

The iron and silicon are the main impurities in aluminium, they are always present in alloys made from commercially pure base material. The solid solubility of iron in aluminium is very low, therefore its largest amount forms intermetallic compounds the kind of which depends strongly on the other impurities of alloying elements. Although the solid solubility of silicon is much larger than that of the iron, it is the constituent of both the primary and the secondary particles, the structure of which depends in general on the iron-silicon concentration ratio. These Fe and Si containing particles can cause various and basic changes in the macroscopic properties of the alloy. Since commercially pure aluminium has extensive consumer and industrial use, it is very important to know, not only from scientific but also from practical point of view, the effect of iron and silicon on the physical and mechanical properties of aluminium and its alloys. The aim of the ''International Workshop on the Effect of Iron and Silicon in Aluminium and its Alloys'' was to clarify the present knowledge on this subject. The thirty papers presented at the Workshop and collected in this Proceedings cover many important fields of the subject. I hope that they will contribute to both the deeper understanding of the related phenomena and the improvement of technologies for producing better aluminium alloys

Coprecipitation of yttrium and aluminium hydroxide for preparation of yttrium aluminium garnet

NARCIS (Netherlands)

Vrolijk, J.W.G.A.; Willems, J.W.M.M.; Metselaar, R.

1990-01-01

Coprecipitation of yttrium and aluminium hydroxide for the preparation of pure yttrium aluminium garnet (YAG) powder with small grain size is the subject of this study. Starting materials are sulphates and chlorides of yttrium and aluminium. To obtain pure YAG (Y3Al5O12), the pH during flocculation

Influence of smelter fumes on the growth of white pine in the Sudbury region

Energy Technology Data Exchange (ETDEWEB)

Linzon, S N

1958-01-01

An additional study was started in 1949 to determine the effects on neighboring white pine forests of sulfur fumes discharged from large smelters operated by two mining companies in the Sudbury district of Ontario. A number of sample timber areas, near to, farther removed, and remote from the sources of the fumes, were placed under observation. Approximately 7000 white pine trees in the vigorous age class of 50 to 90 years had been examined annually by 1954. Foliage on the white pine trees located less than 25 miles northeast of Sudbury showed more extensive injuries every year than foliage on trees located at greater distances from the smelters. Studies of diameter increment showed that there was a gradual decline in the annual growth of white pine in the areas near to the smelters, whereas a constant pattern was maintained in areas located farther from the sources of smoke. Further, in the areas close to the smelters, the volume of white pine lost through excessive tree mortality of all crown class sizes exceeded the volume added by the surviving trees. However, at distances beyond 25 to 30 miles northeast of Sudbury in the direction of the prevailing wind the condition of white pine improved remarkably. It is indicated that the combination of concentration frequency, and duration of atmospheric sulfur dioxide visitations has here declined to a threshold value for the inhibition of growth of white pine. 25 references, 25 figures, 23 tables.

Patterns of insect communities along a stress gradient following decommissioning of a Cu-Ni smelter

International Nuclear Information System (INIS)

Babin-Fenske, Jennifer; Anand, Madhur

2011-01-01

The diversity, estimated richness and abundance of terrestrial insect communities were examined along a stress gradient of past pollution in the region of Sudbury, Ontario, Canada. This gradient represents the natural recovery and lingering effects of a decommissioned copper-nickel smelting complex. Ant genera and sixteen higher taxonomic groups (family and order) had the highest abundance at the sites with intermediate stress. Eight families increased in abundance with distance from the decommissioned source of pollution and eleven families decreased reflecting a complex response of diversity to pollution. Carabid beetles show an increase in diversity further from the smelter; however, examination of the species composition reveals a distinct carabid community closest to the smelter, emphasizing the unique habitat created by severe pollution. Although almost forty years since decomissioning of the smelter complex, the terrestrial insect community in the vicinity remains significantly impacted suggesting slow recovery. - Highlights: → Several taxonomic groups had highest abundance at intermediate stress. → Eight families increased in abundance with distance from the source of pollution. → Eleven families decreased in abundance with distance. → Species composition reveals a distinct carabid community closest to the smelter. → Terrestrial insect community still significantly impacted suggesting slow recovery. - Our study finds both unexpected and expected responses of insect communities to a landscape gradient of past pollution suggesting the emergence of novel ecosystems.

Metal pollution around an iron smelter complex in northern Norway at different modes of operation

International Nuclear Information System (INIS)

Steinnes, E.; Sjoebakk, T.E.; Frontas'eva, M.V.; Varskog, P.

2003-01-01

The moss biomonitoring technique was employed to study the atmospheric deposition in and around the town of Mo i Rana, northern Norway, before and after closing an iron smelter and establishing alternative ferrous metal industries. Samples of Hylocomium splendens were collected from the same sites in 1989 and 1993. A combination of instrumental neutron activation analysis (INAA) and atomic absorption spectrometry was used to obtain data for 38 elements in these moss samples, and the analytical data were subjected to factor analysis. In general, the deposition was higher when the iron smelter was still in operation, in particular for Fe and for many elements normally associated with crustal matter. For Cr there was a substantially increased deposition due to the operation of a new ferrochrome smelter. Also for Ni and Au an increased deposition was observed, whereas for metals such as Mn, Co, Ag, Sb, and W there was no appreciable change. INAA proved to be a powerful tool for this kind of study. The regional distribution of pollutants was strongly dependent on the local topography. Samples of natural surface soils collected simultaneously with the first moss series showed clear signs of contamination with a number of metals from atmospheric deposition. The approach described in this work could be advantageously used to study atmospheric deposition of heavy metals around iron smelters in Russia and elsewhere

Patterns of insect communities along a stress gradient following decommissioning of a Cu-Ni smelter

Energy Technology Data Exchange (ETDEWEB)

Babin-Fenske, Jennifer [Department of Biology, Laurentian University, Sudbury, Ontario, P3E 2C6 (Canada); Anand, Madhur, E-mail: manand@uoguelph.ca [School of Environmental Sciences, University of Guelph, Guelph, Ontario, N1G 2W1 (Canada)

2011-10-15

The diversity, estimated richness and abundance of terrestrial insect communities were examined along a stress gradient of past pollution in the region of Sudbury, Ontario, Canada. This gradient represents the natural recovery and lingering effects of a decommissioned copper-nickel smelting complex. Ant genera and sixteen higher taxonomic groups (family and order) had the highest abundance at the sites with intermediate stress. Eight families increased in abundance with distance from the decommissioned source of pollution and eleven families decreased reflecting a complex response of diversity to pollution. Carabid beetles show an increase in diversity further from the smelter; however, examination of the species composition reveals a distinct carabid community closest to the smelter, emphasizing the unique habitat created by severe pollution. Although almost forty years since decomissioning of the smelter complex, the terrestrial insect community in the vicinity remains significantly impacted suggesting slow recovery. - Highlights: > Several taxonomic groups had highest abundance at intermediate stress. > Eight families increased in abundance with distance from the source of pollution. > Eleven families decreased in abundance with distance. > Species composition reveals a distinct carabid community closest to the smelter. > Terrestrial insect community still significantly impacted suggesting slow recovery. - Our study finds both unexpected and expected responses of insect communities to a landscape gradient of past pollution suggesting the emergence of novel ecosystems.

Toxicity of aluminium on five aquatic invertebrates; Aluminiums toksisitet paa 5 akvatiske invertebrater

Energy Technology Data Exchange (ETDEWEB)

Moe, J [Oslo Univ. (Norway)

1996-01-01

The conference paper deals with the experiments done by investigating the effects from the toxicity of aluminium on aquatic invertebrates. The aim of the experiments was to compare the toxicity of unstable aluminium compounds with stable forms of aluminium. 8 refs., 2 figs., 2 tabs.

Effect of Sintering Temperature on the Properties of Aluminium-Aluminium Oxide Composite Materials

Directory of Open Access Journals (Sweden)

Dewan Muhammad Nuruzzaman

2016-12-01

Full Text Available In this study, aluminium-aluminium oxide (Al-Al2O3 metal matrix composites of different weight percentage reinforcements of aluminium oxide were processed at different sintering temperatures. In order to prepare these composite specimens, conventional powder metallurgy (PM method was used. Three types specimens of different compositions such as 95%Al+5%Al2O3, 90%Al+10%Al2O3 and 85%Al+15%Al2O3 were prepared under 20 Ton compaction load. Then, all the specimens were sintered in a furnace at two different temperatures 550oC and 580oC. In each sintering process, two different heating cycles were used. After the sintering process, it was observed that undistorted flat specimens were successfully prepared for all the compositions. The effects of sintering temperature and weight fraction of aluminium oxide particulates on the density, hardness and microstructure of Al-Al2O3 composites were observed. It was found that density and hardness of the composite specimens were significantly influenced by sintering temperature and percentage aluminium oxide reinforcement. Furthermore, optical microscopy revealed that almost uniform distribution of aluminium oxide reinforcement within the aluminium matrix was achieved.

Contamination and health risks of soil heavy metals around a lead/zinc smelter in southwestern China.

Science.gov (United States)

Li, Peizhong; Lin, Chunye; Cheng, Hongguang; Duan, Xiaoli; Lei, Kai

2015-03-01

Anthropogenic emissions of toxic metals from smelters are a global problem. The objective of this study was to investigate the distribution of toxic metals in soils around a 60 year-old Pb/Zn smelter in a town in Yunnan Province of China. Topsoil and soil core samples were collected and analyzed to determine the concentrations of various forms of toxic metals. The results indicated that approximately 60 years of Pb/Zn smelting has led to significant contamination of the local soil by Zn, Pb, Cd, As, Sb, and Hg, which exhibited maximum concentrations of 8078, 2485, 75.4, 71.7, 25.3, and 2.58mgkg(-1), dry wet, respectively. Other metals, including Co, Cr, Cu, Mn, Ni, Sc, and V, were found to originate from geogenic sources. The concentrations of smelter driven metals in topsoil decreased with increasing distance from the smelter. The main contamination by Pb, Zn, and Cd was found in the upper 40cm of soil around the Pb/Zn smelter, but traces of Pb, Zn, and Cd contamination were found below 100cm. Geogenic Ni in the topsoil was mostly bound in the residual fraction (RES), whereas anthropogenic Cd, Pb, and Zn were mostly associated with non-RES fractions. Therefore, the smelting emissions increased not only the concentrations of Cd, Pb, and Zn in the topsoil but also their mobility and bioavailability. The hazard quotient and hazard index showed that the topsoil may pose a health risk to children, primarily due to the high Pb and As contents of the soil. Copyright © 2014 Elsevier Inc. All rights reserved.

Heavy metals in white-tailed deer living near a zinc smelter in Pennsylvania

Science.gov (United States)

Sileo, Louis; Beyer, W. Nelson

1985-01-01

White-tailed deer (Odocoileus virginianus (Zimmermann)) shot within 20 km of the zinc smelters in the Palmerton, Pennsylvania area contained extremely high renal concentrations of cadmium (372 ppm dry weight (dw)) and zinc (600 ppm dw). The deer with the highest renal zinc concentration was shot 4 km from the smelters and had joint lesions similar to those seen in zinc-poisoned horses from the same area. The highest concentrations of lead in both hard and soft tissues were relatively low, 10.9 ppm dw in a sample of teeth, 17.4 ppm dw in a metacarpus, and 4.9 ppm dw in a kidney.

Dispersion strengthening of aluminium-aluminium-oxide products

DEFF Research Database (Denmark)

Hansen, Niels

1970-01-01

The true stress-true strain curves at room temperature and at 400°C were determined for various types of aluminium-aluminium-oxide products containing from 0.2 to 4.7 weight per cent of aluminium oxide. The effect of particles on the initial flow stress and the flow stress for 0.2% offset at room...... temperature and at 400°C is in agreement with Orowan's theory. The increase in flow stress at room temperature for strain values below 3 per cent was related to the plastic strain by the equation σ-σoy=k1ε 1/2, where σoy is the initial flow stress and where k1 increases for increasing volume fraction...... and decreasing particle size of the dispersed particles. A general expression for k1 was derived for the relationship between the dislocation density and the strain in dispersion-strengthened products...

Estimating mercury emissions from a zinc smelter in relation to China's mercury control policies

International Nuclear Information System (INIS)

Wang, S.X.; Song, J.X.; Li, G.H.; Wu, Y.; Zhang, L.; Wan, Q.; Streets, D.G.; Chin, Conrad K.; Hao, J.M.

2010-01-01

Mercury concentrations of flue gas at inlet/outlet of the flue gas cleaning, electrostatic demister, reclaiming tower, acid plant, and mercury contents in zinc concentrate and by-products were measured in a hydrometallurgical zinc smelter. The removal efficiency of flue gas cleaning, electrostatic demister, mercury reclaiming and acid plant was about 17.4%, 30.3%, 87.9% and 97.4% respectively. Flue gas cleaning and electrostatic demister captured 11.7% and 25.3% of the mercury in the zinc concentrate, respectively. The mercury reclaiming tower captured 58.3% of the mercury in the zinc concentrate. About 4.2% of the mercury in the zinc concentrate was captured by the acid plant. Consequently, only 0.8% of the mercury in the zinc concentrate was emitted to the atmosphere. The atmospheric mercury emission factor was 0.5 g t -1 of zinc produced for the tested smelter, indicating that this process offers the potential to effectively reduce mercury emissions from zinc smelting. - Modern scale production equipped with acid plant and Hg reclaiming tower will significantly reduce Hg emissions from zinc smelters in China.

Metal Pollution Around an Iron Smelter Complex in Northern Norway at Different Modes of Operation

CERN Document Server

Steinnes, E; Eidhammer-Sjobakk, T; Varskog, P

2003-01-01

The moss biomonitoring technique was employed to study the atmospheric deposition in and around the town of Mo i Rana, northern Norway, before and after closing an iron smelter and establishing alternative ferrous metal industries. Samples of Hylocomium splendens were collected from the same sites in 1989 and 1993. A combination of instrumental neutron activation analysis (INAA) and atomic absorption spectrometry was used to obtain data for 38 elements in these moss samples, and the analytical data were subjected to factor analysis. In general, the deposition was higher when the iron smelter was still in operation, in particular for Fe and for many elements normally associated with crustal matter. For Cr there was a substantially increased deposition due to the operation of a new ferrochrome smelter. Also for Ni and Au an increased deposition was observed, whereas for metals such as Mn, Co, Ag, Sb, and W there was no appreciable change. INAA proved to be a powerful tool for this kind of study. The regional di...

The prophylactic reduction of aluminium intake.

Science.gov (United States)

Lione, A

1983-02-01

The use of modern analytical methods has demonstrated that aluminium salts can be absorbed from the gut and concentrated in various human tissues, including bone, the parathyroids and brain. The neurotoxicity of aluminium has been extensively characterized in rabbits and cats, and high concentrations of aluminium have been detected in the brain tissue of patients with Alzheimer's disease. Various reports have suggested that high aluminium intakes may be harmful to some patients with bone disease or renal impairment. Fatal aluminium-induced neuropathies have been reported in patients on renal dialysis. Since there are no demonstrable consequences of aluminium deprivation, the prophylactic reduction of aluminium intake by many patients would appear prudent. In this report, the major sources of aluminium in foods and non-prescription drugs are summarized and alternative products are described. The most common foods that contain substantial amounts of aluminium-containing additives include some processed cheeses, baking powders, cake mixes, frozen doughs, pancake mixes, self-raising flours and pickled vegetables. The aluminium-containing non-prescription drugs include some antacids, buffered aspirins, antidiarrhoeal products, douches and haemorrhoidal medications. The advisability of recommending a low aluminium diet for geriatric patients is discussed in detail.

The impact of a copper smelter on adjacent soil zinc and cadmium fractions and soil organic carbon

Energy Technology Data Exchange (ETDEWEB)

Liu Ling; Wu Longhua; Luo Yongming [Key Lab. of Soil Environment and Pollution Remediation, Chinese Academy of Sciences, NJ (China); Zhang Changbo [Shanghai Academy of Environmental Sciences, SH (China); Jiang Yugen; Qiu Xiya [Soils and Fertilisers Div., Fuyang City Agricultural Bureau, Hangzhou, ZJ (China)

2010-07-15

Purpose: We investigated the chemical fractions of Zn, Cd and Cu in soils collected from positions at different distances from a copper smelter and studied the relationships between distribution patterns of Zn, Cd and Cu, fractions and soil organic carbon (SOC), especially ''black carbon'' (BC), in contaminated soils. The relationships between soil particle size and concentrations of Zn and Cd in contaminated soil were also examined. Materials and methods: Soil samples were collected from field sites at different distances from the copper smelter, air-dried and passed through 0.25-mm and 0.149-mm nylon mesh sieves. The SOC and BC were determined. Aqua regia and sequentially extracted Zn, Cd and Cu fractions in soil and the different sizes of soil particles, and metal concentrations (Zn, Cd and Cu) in BC were also determined. Results and discussion: The soils were heavily contaminated by fly ash from the copper smelter. Concentrations of Zn, Cd and Cu in soil and SOC decreased with increasing distance from the smelter. Concentrations of Zn and Cd in the surface soil (0-15 cm) decreased from 27,017 to 892 mg kg{sup -1} and from 18.7 to 1.04 mg kg{sup -1}, respectively. Soil BC and concentrations of Zn, Cd and Cu in the BC fraction showed significant and positive relationships with the corresponding aqua regia metal concentrations in soil. Soil Zn and Cd occurred predominantly in the exchangeable and reducible fractions, but residual and oxidisable fractions of Cu that were not considered mobile or bioavailable were predominant (>60%). Concentrations of Zn and Cd in the soil particle size fractions tended to increase with decreasing particle size. Conclusions: The Cd and Zn and BC were all derived from the fly ash of the smelter. Concentrations of Zn and Cd and BC in the soil decreased significantly with increasing distance from the smelter. Zinc and Cd in contaminated soils increased as particle size decreased, and were mainly in highly available

The structure of spruce-fir tree stands mortality under impact of the Middle Ural copper smelter emissions

Directory of Open Access Journals (Sweden)

I. E. Bergman

2015-04-01

Full Text Available The influence of industrial pollution on mortality values (dead fallen wood and dead standing trees and its distribution by degrees of decomposition were investigated in spruce-fir forest stands in the vicinity of the Middle Ural copper smelter (the city of Revda, Sverdlovsk region. The total mortality and mortality in each size category did not depend on the distance to the source of pollution. At the same time, the amount of dead fallen wood was significantly greater (1.9 times in the polluted area (2 and 4 km from the smelter as compared with the background territory (30 km from the smelter. Mortality proportion out of the total number of the trees (both live and dead did not differ significantly between the sites, although this parameter tended to increase nearer the smelter. The distribution of mortality by size categories revealed significant differences between background territory and site with average level of contamination, as well as background territory and highly contaminated site. Observed differences are associated with an increased proportion of lesser mortality near the smelter (by 15 % and 12 % as compared with areas of background and middle levels of contamination, respectively, as well as because of double-declining of medium- and large-sized mortality near the smelter. The distribution of the living tree stands by size categories also has a connection with level of contamination. The average diameters of the living tree stand and the elements of coarse woody debris (dead fallen wood and dead standing trees do not differ significantly between sites with different levels of contamination. For the small-sized dead fallen wood, the proportion of weakly decomposed stems increased with the level of pollution, while proportion of strongly decomposed stems decreased. The distribution of medium- and large-sized dead fallen wood on the stages of decomposition does not vary between sites with different levels of pollution.

Impact of mercury mine and smelter St. Ana – Podljubelj on spatial distribution of chemical elements in soil

Directory of Open Access Journals (Sweden)

Tamara Teršič

2005-06-01

Full Text Available The objective of the research project was to establish the extension of Hg pollution as a consequence of mining and smelting activities in a narrow Alpine valley. The St. Ana mine was first exploited as early as in 1557 and was finally abandoned in 1902. The entire operating period yielded about 110.000 tons of ore, from which 360 tons of Hg was produced. By soil sampling it was established that on about 9 ha the Hg contents in soil exceed the Slovenian critical values for soil (10 mg/kg. The estimated mercury mean for the studied area is 1.3 mg/kg (0.17 – 718 mg/kg. The highest contents of mercury in soilswere found in the area of the mercury smelter.That is a consequence of former atmospheric emissions and technological losses. High values of Hg were found also in soil on the mine and smelter waste dump. The highest determined contents of Hg (108 mg/kg in this area are almost 7-times lower than thecontents of Hg in the area of the smelter. Mercury in soils generally decrease with depth and distance from the mine and smelter. Apart from the area around the former mine and smelter, mercury appear in higher concentrations also along the road that runs along thevalley, which is due to the use of Hg bearing mine tailings in road construction.

Investigation of the aluminium-aluminium oxide reversible transformation as observed by hot stage electron microscopy.

Science.gov (United States)

Grove, C. A.; Judd, G.; Ansell, G. S.

1972-01-01

Thin foils of high purity aluminium and an Al-Al2O3 SAP type of alloy were oxidised in a specially designed hot stage specimen chamber in an electron microscope. Below 450 C, amorphous aluminium oxide formed on the foil surface and was first detectable at foil edges, holes, and pits. Islands of aluminium then nucleated in this amorphous oxide. The aluminium islands displayed either a lateral growth with eventual coalescence with other islands, or a reoxidation process which caused the islands to disappear. The aluminium island formation was determined to be related to the presence of the electron beam. A mechanism based upon electron charging due to the electron beam was proposed to explain the nucleation, growth, coalescence, disappearance, and geometry of the aluminium islands.

TEM investigation of aluminium containing precipitates in high aluminium doped silicon carbide

International Nuclear Information System (INIS)

Wong-Leung, J.; FitzGerald, J.D.

2002-01-01

Full text: Silicon carbide is a promising semiconductor material for applications in high temperature and high power devices. The successful growth of good quality epilayers in this material has enhanced its potential for device applications. As a novel semiconductor material, there is a need for studying its basic physical properties and the role of dopants in this material. In this study, silicon carbide epilayers were grown on 4H-SiC wafers of (0001) orientation with a miscut angle of 8 deg at a temperature of 1550 deg C. The epilayers contained regions of high aluminium doping well above the solubility of aluminium in silicon carbide. High temperature annealing of this material resulted in the precipitation of aluminium in the wafers. The samples were analysed by secondary ion mass spectrometry and transmission electron microscopy. Selected area diffraction studies show the presence of aluminium carbide and aluminium silicon carbide phases. Copyright (2002) Australian Society for Electron Microscopy Inc

Reductive-sulfurizing smelting treatment of smelter slag for copper and cobalt recovery

Directory of Open Access Journals (Sweden)

Li Y.

2018-01-01

Full Text Available Recovery of copper and cobalt from smelter slag using reductive-sulfurizing smelting method was performed in this study. The effects of reductive agent (coke, sulfurizing agent (pyrite, slag modifier (CaO and smelting temperature and duration on the extractive efficiencies of Cu, Co and Fe were discussed. The phase compositions and microstructure of the materials, copper-cobalt matte and cleaned slag were determined. The results showed that copper and cobalt contents in cleaned slag could decrease averagely to 0.18% and 0.071% respectively after cleaning. 91.99% Cu and 92.94% Co and less than 38.73% Fe were recovered from the smelter slag under the optimum conditions: 6 wt.% coke, 20 wt.% pyrite and 6 wt.% CaO addition to the smelter slag, smelting temperature of 1350°C and smelting duration of 3h. The addition of CaO can increase the selectivity of Co recovery. The cleaning products were characterized by XRD and SEM-EDS analysis. The results showed that the main phases of copper-cobalt matte were iron sulfide (FeS, geerite (Cu8S5, iron cobalt sulfide (Fe0.92Co0.08S and Fe-Cu-Co alloy. The cleaned slag mainly comprised fayalite (Fe2SiO4, hedenbergite (CaFe(Si2O6 and magnetite (Fe3O4.

Bio-processing of copper from combined smelter dust and flotation concentrate: a comparative study on the stirred tank and airlift reactors.

Science.gov (United States)

Vakylabad, Ali Behrad; Schaffie, Mahin; Ranjbar, Mohammad; Manafi, Zahra; Darezereshki, Esmaeel

2012-11-30

To scrutinize the influence of the design and type of the bioreactors on the bioleaching efficiency, the bioleaching were evaluated in a batch airlift and a batch stirred tank bioreactors with mixed mesophilic and mixed moderately thermophilic bacteria. According to the results, maximum copper recoveries were achieved using the cultures in the stirred tank bioreactors. It is worth noting that the main phase of the flotation concentrate was chalcopyrite (as a primary sulphide), but the smelter dust mainly contained secondary copper sulphides such as Cu(2)S, CuS, and Cu(5)FeS(4).Under optimum conditions, copper dissolution from the combined flotation concentrate and smelter dust (as an environmental hazard) reached 94.50% in the STR, and 88.02% in the airlift reactor with moderately thermophilic, after 23 days. Also, copper extractions calculated for the bioleaching using mesophilic bacteria were 48.73% and 37.19% in the STR (stirred tank reactor) and the airlift bioreactor, respectively. In addition, the SEM/EDS, XRD, chemical, and mineralogical analyses and studies confirmed the above results. Copyright © 2012 Elsevier B.V. All rights reserved.

Factors affecting the aluminium content of human femoral head and neck.

Science.gov (United States)

Zioła-Frankowska, Anetta; Dąbrowski, Mikołaj; Kubaszewski, Łukasz; Rogala, Piotr; Frankowski, Marcin

2015-11-01

Tissues for the study were obtained intraoperatively during hip replacement procedures from 96 patients. In all the cases, the indication for this treatment was primary or secondary degenerative changes in the hip joint. The subject of the study was the head and neck of the femur, resected in situ. Aluminium concentrations measured in femoral head and neck samples from patients aged between 25 and 91 were varied. Statistical methods were applied to determine the variations in relation to the parameters from the background survey. Significant differences in the aluminium content of femoral head samples were observed between patients under and over 60 years of age. Based on the results, it was confirmed that the aluminium accumulates in bones over a lifetime. The study showed that the content of aluminium in the head and neck of the femur depends on the factors such as: type of medicines taken, contact with chemicals at work, differences in body anatomy and sex. The study on the levels of aluminium in bones and the factors affecting its concentration is a valuable source of information for further research on the role of aluminium in bone diseases. Based on the investigations, it was found that the GF-AAS technique is the best analytical tool for routine analysis of aluminium in complex matrix samples. The use of femoral heads in the investigations was approved by the Bioethics Committee of the University of Medical Sciences in Poznań (Poland). Copyright © 2015 Elsevier Inc. All rights reserved.

Transformation of arsenic-rich copper smelter flue dust in contrasting soils: A 2-year field experiment.

Science.gov (United States)

Jarošíková, Alice; Ettler, Vojtěch; Mihaljevič, Martin; Penížek, Vít; Matoušek, Tomáš; Culka, Adam; Drahota, Petr

2018-06-01

Dust emissions from copper smelters processing arsenic-bearing ores represent a risk to soil environments due to the high levels of As and other inorganic contaminants. Using an in situ experiment in four different forest and grassland soils (pH 3.2-8.0) we studied the transformation of As-rich (>50 wt% As) copper smelter dust over 24 months. Double polyamide bags with 1 g of flue dust were buried at different depths in soil pits and in 6-month intervals; then those bags, surrounding soil columns, and soil pore waters were collected and analysed. Dust dissolution was relatively fast during the first 6 months (5-34%), and mass losses attained 52% after 24 months. The key driving forces affecting dust dissolution were not only pH, but also the water percolation/retention in individual soils. Primary arsenolite (As 2 O 3 ) dissolution was responsible for high As release from the dust (to 72%) and substantial increase of As in the soil (to a 56 × increase; to 1500 mg kg -1 ). Despite high arsenolite solubility, this phase persisted in the dust after 2 years of exposure. Mineralogical investigation indicated that mimetite [Pb 5 (AsO 4 ) 3 (Cl,OH)], unidentified complex Ca-Pb-Fe-Zn arsenates, and Fe oxyhydroxides partly controlled the mobility of As and other metal(loid)s. Compared to As, other less abundant contaminants (Bi, Cu, Pb, Sb, Zn) were released into the soil to a lesser extent (8-40% of total). The relatively high mobility of As in the soil can be seen from decreases of bulk As concentrations after spring snowmelt, high water-extractable fractions with up to ∼50% of As(III) in extracts, and high As concentrations in soil pore waters. Results indicate that efficient controls of emissions from copper smelters and flue dust disposal sites are needed to prevent extensive contamination of nearby soils by persistent As. Copyright © 2018 Elsevier Ltd. All rights reserved.

Aluminium based adjuvants and their effects on mitochondria and lysosomes of phagocytosing cells.

Science.gov (United States)

Ohlsson, Lars; Exley, Christopher; Darabi, Anna; Sandén, Emma; Siesjö, Peter; Eriksson, Håkan

2013-11-01

Aluminium oxyhydroxide, Al(OH)3 is one of few compounds approved as an adjuvant in human vaccines. However, the mechanism behind its immune stimulating properties is still poorly understood. In vitro co-culture of an aluminium adjuvant and the human monocytic cell line THP-1 resulted in reduced cell proliferation. Inhibition occurred at concentrations of adjuvant several times lower than would be found at the injection site using a vaccine formulation containing an aluminium adjuvant. Based on evaluation of the mitochondrial membrane potential, THP-1 cells showed no mitochondrial rupture after co-culture with the aluminium adjuvant, instead an increase in mitochondrial activity was seen. The THP-1 cells are phagocytosing cells and after co-culture with the aluminium adjuvant the phagosomal pathway was obstructed. Primary or early phagosomes mature into phagolysosomes with an internal pH of 4.5 - 5 and carry a wide variety of hydrolysing enzymes. Co-culture with the aluminium adjuvant yielded a reduced level of acidic vesicles and cathepsin L activity, a proteolytic enzyme of the phagolysosomes, was almost completely inhibited. THP-1 cells are an appropriate in vitro model in order to investigate the mechanism behind the induction of a phagocytosing antigen presenting cell into an inflammatory cell by aluminium adjuvants. Much information will be gained by investigating the phagosomal pathway and what occurs inside the phagosomes and to elucidate the ultimate fate of phagocytosed aluminium particles. © 2013.

Analysis of aluminium in rat following administration of allergen immunotherapy using either aluminium or microcrystalline-tyrosine-based adjuvants.

Science.gov (United States)

McDougall, Stuart A; Heath, Matthew D; Kramer, Matthias F; Skinner, Murray A

2016-03-01

Investigation into the absorption, distribution and elimination of aluminium in rat after subcutaneous aluminium adjuvant formulation administration using ICP-MS is described. Assays were verified under the principles of a tiered approach. There was no evidence of systemic exposure of aluminium, in brain or in kidney. Extensive and persistent retention of aluminium at the dose site was observed for at least 180 days after administration. This is the first published work that has quantified aluminium adjuvant retention based on the quantity of aluminium delivered in a typical allergy immunotherapy course. The results indicate that the repeated administration of aluminium-containing adjuvants will likely contribute directly and significantly to an individual's body burden of aluminium.

TITANIUM CARBON ALUMINIUM : A NOVEL GRAIN REFINER FOR ALUMINIUM-LITHIUM ALLOYS

OpenAIRE

Birch , M.; Cowell , A.

1987-01-01

This work explores the possibility of achieving grain size control in aluminium-lithium alloys with the titanium carbon aluminium (TiCAl) master alloys invented at the Technical University of Berlin and developed by London and Scandinavian Metallurgical Co Ltd (LSM). Grain refining tests were conducted on a single batch of 8090 alloy using addition rates of 0.2wt% and 0.4wt% of TiCAl and 3/1 titanium boron aluminium (TiBAl). Other tests using 0.4wt% of binary TiAl gave poor results, showing t...

Lead distribution in soils impacted by a secondary lead smelter: Experimental and modelling approaches

Energy Technology Data Exchange (ETDEWEB)

Schneider, Arnaud R., E-mail: arnaud.schneider@univ-reims.fr [GEGENAA, EA 3795, Université de Reims Champagne-Ardenne, SFR Condorcet FR CNRS 3417, 2 esplanade Roland Garros, 51100 Reims (France); Cancès, Benjamin; Ponthieu, Marie [GEGENAA, EA 3795, Université de Reims Champagne-Ardenne, SFR Condorcet FR CNRS 3417, 2 esplanade Roland Garros, 51100 Reims (France); Sobanska, Sophie [Laboratoire de Spectrochimie IR et Raman, UMR-CNRS 8516, Bât. C5 Université de Lille I, 59655 Villeneuve d' Ascq Cedex (France); Benedetti, Marc F. [Institut de Physique du Globe de Paris, Sorbonne Paris Cité, Université Paris Diderot, UMR 7154, CNRS, F-75005 Paris (France); Pourret, Olivier [HydrISE, Institut Polytechnique LaSalle Beauvais, FR-60000 Beauvais (France); Conreux, Alexandra; Calandra, Ivan; Martinet, Blandine; Morvan, Xavier; Gommeaux, Maxime; Marin, Béatrice [GEGENAA, EA 3795, Université de Reims Champagne-Ardenne, SFR Condorcet FR CNRS 3417, 2 esplanade Roland Garros, 51100 Reims (France)

2016-10-15

Smelting activities are one of the most common sources of trace elements in the environment. The aim of this study was to determine the lead distribution in upper horizons (0–5 and 5–10 cm) of acidic soils in the vicinity of a lead-acid battery recycling plant in northern France. The combination of chemical methods (sequential extractions), physical methods (Raman microspectroscopy and scanning electron microscopy with an energy dispersive spectrometer) and multi-surface complexation modelling enabled an assessment of the behaviour of Pb. Regardless of the studied soil, none of the Pb-bearing phases commonly identified in similarly polluted environments (e.g., anglesite) were observed. Lead was mainly associated with organic matter and manganese oxides. The association of Pb with these soil constituents can be interpreted as evidence of Pb redistribution in the studied soils following smelter particle deposition. - Highlights: • Lead behavior was studied in smelter impacted soils. • A combination of experimental methods and modelling was employed. • Pb was mainly associated with organic matter and to a lesser degree with Mn oxides. • Pb was redistributed in soils after smelter particle deposition.

Lead distribution in soils impacted by a secondary lead smelter: Experimental and modelling approaches

International Nuclear Information System (INIS)

Schneider, Arnaud R.; Cancès, Benjamin; Ponthieu, Marie; Sobanska, Sophie; Benedetti, Marc F.; Pourret, Olivier; Conreux, Alexandra; Calandra, Ivan; Martinet, Blandine; Morvan, Xavier; Gommeaux, Maxime; Marin, Béatrice

2016-01-01

Smelting activities are one of the most common sources of trace elements in the environment. The aim of this study was to determine the lead distribution in upper horizons (0–5 and 5–10 cm) of acidic soils in the vicinity of a lead-acid battery recycling plant in northern France. The combination of chemical methods (sequential extractions), physical methods (Raman microspectroscopy and scanning electron microscopy with an energy dispersive spectrometer) and multi-surface complexation modelling enabled an assessment of the behaviour of Pb. Regardless of the studied soil, none of the Pb-bearing phases commonly identified in similarly polluted environments (e.g., anglesite) were observed. Lead was mainly associated with organic matter and manganese oxides. The association of Pb with these soil constituents can be interpreted as evidence of Pb redistribution in the studied soils following smelter particle deposition. - Highlights: • Lead behavior was studied in smelter impacted soils. • A combination of experimental methods and modelling was employed. • Pb was mainly associated with organic matter and to a lesser degree with Mn oxides. • Pb was redistributed in soils after smelter particle deposition.

Verification of Some Vegetable Oils as Cutting Fluid for Aluminium

African Journals Online (AJOL)

Akorede

kerosene (due to the gummy nature of aluminium metal). The parameters ... In the cutting of metals, work is done in the plastic deformation of the layer being cut at the primary shear ... Lathe machine – Model: Metalx WARSZAWA,. Serial No.

Generic assessment of radiation exposures to workers in a portable smelter and to the surrounding population

International Nuclear Information System (INIS)

Randolph, M.L.; Watson, A.P.; O'Donnell, F.R.

1978-10-01

A scenario for operation of a proposed portable smelter has been developed by National Lead Company of Ohio to recycle radioactively contaminated ferrous scrap arising from modifications at nuclear facilities of the Department of Energy. The current generic study complements that work by developing tables of radiation dose conversion factors for estimation of external whole-body doses and 50-year whole-body internal dose commitments to routine workers in the smelter and to the public within 50 miles of the smelter. Applications of the tables to specific cases require site-specific source terms consisting of amounts of radionuclides present in scrap metal, separation efficiency for radionuclides, concentration of contaminated airborne particulates, ingested amount of contaminated material, and amount of metal released through the stack. Equations relating doses to tabular values and these source terms are developed, and hypothetical sample calculations are given. Assumptions, approximations, and limitations of the methods are discussed as well as nonroutine operations and nonradioactive hazards

Aluminium in Infrastructures

NARCIS (Netherlands)

Maljaars, J.

2016-01-01

Aluminium alloys are used in infrastructures such as pedestrian bridges or parts of it such as handrail. This paper demonstrates that aluminium alloys are in principle also suited for heavy loaded structures, such as decks of traffic bridges and helicopter landing platforms. Recent developments in

Climate Policy and Carbon Leakage

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-07-01

This report explores the effects of the EU emissions trading scheme on the aluminium sector (i.e. competitiveness loss and carbon leakage). With its very high electricity intensity, primary aluminium stands out in the heavy industry picture: a sector whose emissions are not capped in the present EU ETS, European aluminium smelters still stand to lose profit margins and, possibly, market shares, as electricity prices increase following CO2 caps on generators' emissions - the famous pass-through of CO2 prices into electricity prices. The analysis includes a method of quantification of this issue, based on two indicators: profit margins and trade flows. As the EU is at the forefront of such policy, the paper provides policy messages to all countries on how trade exposed energy-intensive industries can be 'moved' by carbon constraint. This also is a contentious topic in Australia, Japan, New Zealand, and the US, where ambitious climate policies -- including cap-and-trade systems -- are currently debated.

Formation of aluminium nitride and segregation of Cu impurity atoms in aluminium implanted by high dose nitrogen ions

International Nuclear Information System (INIS)

Lin Chenglu; Hemment, P.L.F.; Li Jinhua; Zou Shichang

1994-01-01

Aluminium films with a thickness of 7000 A (containing 0.85% copper) were deposited on silicon substrates. 400 keV N 2 + or 350 keV N + ions were implanted into the aluminium films or at the interface between the aluminium and silicon, respectively. Automatic spreading resistance (ASR), Fourier transform infrared spectroscopy (FTIR) and Rutherford backscattering (RBS) and channelling were used to characterize the formation of aluminium nitride and the depth distribution of the Cu impurity in the aluminium films after ion implantation and post-annealing. The formation of a stoichiometric AlN layer with high resistance was evident from ASR, RBS analysis and FTIR measurements by the presence of the absorption band at 650 cm -1 . When the implanted nitrogen is near the interface between the aluminium and silicon, a multilayer structure can be obtained, which consists of aluminium, aluminium nitride and the silicon substrate. Cu, which is a background impurity in the deposited aluminium films, segregated into the synthesised aluminium nitride during high dose nitrogen ion implantation. This is due to irradiation-induced segregation during ion implantation. (orig.)

Ion nitriding of aluminium

International Nuclear Information System (INIS)

Fitz, T.

2002-09-01

The present study is devoted to the investigation of the mechanism of aluminium nitriding by a technique that employs implantation of low-energy nitrogen ions and diffusional transport of atoms. The nitriding of aluminium is investigated, because this is a method for surface modification of aluminium and has a potential for application in a broad spectrum of fields such as automobile, marine, aviation, space technologies, etc. However, at present nitriding of aluminium does not find any large scale industrial application, due to problems in the formation of stoichiometric aluminium nitride layers with a sufficient thickness and good quality. For the purposes of this study, ion nitriding is chosen, as an ion beam method with the advantage of good and independent control over the process parameters, which thus can be related uniquely to the physical properties of the resulting layers. Moreover, ion nitriding has a close similarity to plasma nitriding and plasma immersion ion implantation, which are methods with a potential for industrial application. (orig.)

Preliminary studies of airborne particulate emmisions from the Ampellum S.A. copper smelter, Zlatna, Romania

Directory of Open Access Journals (Sweden)

Ben J. Williamson

2003-04-01

Full Text Available Preliminary studies have been carried on the characterization of particulate emissions from the Ampellum S.A. copper smelter in the town of Zlatna, Romania. The particulates studied were collected on polycarbonate filters using air pump apparatus and on the surfaces of lichens. Mass of total suspended particulates (TSP and PM10 varied from 19 to 230 μg/m3 and 3 to 146 μg/m3, respectively (PM10/TSP = 0.14 to 1.0, depending on wind direction and proximity to the smelter. Particulates on collection filters from a site directly downwind from the smelter have a mean equivalent spherical diameter (ESD of 0.94 μm (s.d. 1.1 and are dominantly made up of material with the composition of anglesite (PbSO4. The remainder of the material is a heterogeneous mixture of silicates and Fe-, Pb- and Cu-bearing phases. Particulates > 5 μm ESD are rare on the TSP filters, mainly due to the restricted sampling durations possible with the equipment used (<3 hours. Particulates have therefore been studied in the lichen Acarospora smaragdula, which was growing on posts downwind from the smelter and which was found to contain high levels and a broader range of particulates compared with the filters (<5 to 100 μm in diameter. Larger particles include 20-30 μm diameter Fe-rich spherules, which occasionally have Pb- and S-rich encrustations on their surfaces. The nature and possible health effects of the particulates are discussed and recommendations made for future studies.

Osmium isotopic tracing of atmospheric emissions from an aluminum smelter

Science.gov (United States)

Gogot, Julien; Poirier, André; Boullemant, Amiel

2015-09-01

We present for the first time the use of osmium isotopic composition as a tracer of atmospheric emissions from an aluminum smelter, where alumina (extracted from bauxite) is reduced through electrolysis into metallic aluminum using carbonaceous anodes. These anodes are consumed in the process; they are made of petroleum coke and pitch and have high Re/Os elementary ratio. Due to the relatively large geological age of their source material, their osmium shows a high content of radiogenic 187Os produced from in situ187Re radioactive decay. The radiogenic isotopic composition (187Os/188Os ∼ 2.5) of atmospheric particulate emissions from this smelter is different from that of other typical anthropogenic osmium sources (that come from ultramafic geological contexts with unradiogenic Os isotopes, e.g., 187Os/188Os < 0.2) and also different from average eroding continental crust 187Os/188Os ratios (ca. 1.2). This study demonstrates the capacity of osmium measurements to monitor particulate matter emissions from the Al-producing industry.

Variation in aluminium patch test reactivity over time.

Science.gov (United States)

Siemund, Ingrid; Mowitz, Martin; Zimerson, Erik; Bruze, Magnus; Hindsén, Monica

2017-11-01

Contact allergy to aluminium has been reported more frequently in recent years. It has been pointed out that positive patch test reactions to aluminium may not be reproducible on retesting. To investigate possible variations in patch test reactivity to aluminium over time. Twenty-one adults, who had previously reacted positively to aluminium, were patch tested with equimolar dilution series in pet. of aluminium chloride hexahydrate and aluminium lactate, four times over a period of 8 months. Thirty-six of 84 (43%) serial dilution tests with aluminium chloride hexahydrate and 49 of 84 (58%) serial dilution tests with aluminium lactate gave negative results. The range of reactivity varied between a negative reaction to aluminium chloride hexahydrate at 10% and/or to aluminium lactate at 12%, and a positive reaction to aluminium chloride hexahydrate at 0.1% and/or to aluminium lactate at 0.12%. The highest individual difference in test reactivity noticed was 320-fold when the two most divergent minimal eliciting concentrations were compared. The patch test reactivity to aluminium varies over time. Aluminium-allergic individuals may have false-negative reactions. Therefore, retesting with aluminium should be considered when there is a strong suspicion of aluminium contact allergy. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Controls on Metal Leaching from Secondary Pb Smelter Air-Pollution-Control Residues

Czech Academy of Sciences Publication Activity Database

Ettler, V.; Šebek, O.; Grygar, Tomáš; Klementová, Mariana; Bezdička, Petr

2008-01-01

Roč. 42, č. 21 (2008), s. 7878-7884 ISSN 0013-936X Institutional research plan: CEZ:AV0Z40320502 Keywords : lead smelter * waste incineration * soils Subject RIV: CA - Inorganic Chemistry Impact factor: 4.458, year: 2008

Ammonia leaching of copper smelter dust and precipitation as copper sulphide; Lixiviacion amoniacal de polvos de fundicion de cobre y precipitacion como sulfuro de cobre

Energy Technology Data Exchange (ETDEWEB)

Morales, A.; Hevia, J. F.; Cifuentes, G.

2009-07-01

The effect of ammonia on the leaching of copper smelter dust and copper precipitation from these solutions as sulphide using sulfur and sulfur dioxide was studied. The precipitation was done in ammoniacal media because this solution produced more satisfactory results at room temperature that a sulphuric media. A solid was precipitated containing 60 % of copper of the dust smelter. The other waste generated contained around 80 % of the arsenic of the original copper smelter dust. Based on the preliminary results obtained in this work it will propose a procedure for the recovery of copper as sulphide from copper smelter dust with parallel confinement of arsenic. (Author) 14 refs.

Recovery in aluminium

DEFF Research Database (Denmark)

Gundlach, Carsten

2006-01-01

In the present thesis the development of a unique experimental method for volume characterisation of individual embedded crystallites down to a radius of 150 nm is presented. This method is applied to in-situ studies of recovery in aluminium. The method is an extension of 3DXRD microscopy, an X...... are represented as strings. To identify the strings a combination of a 5D connected component type algorithm and multi-peak fitting was found to be superior. The first use of the method was a study of recovery of a deformed aluminium alloy (AA1050). The aluminium alloy was deformed by cold rolling to a thickness...

New insight into atmospheric mercury emissions from zinc smelters using mass flow analysis.

Science.gov (United States)

Wu, Qingru; Wang, Shuxiao; Hui, Mulin; Wang, Fengyang; Zhang, Lei; Duan, Lei; Luo, Yao

2015-03-17

The mercury (Hg) flow paths from three zinc (Zn) smelters indicated that a large quantity of Hg, approximately 38.0-57.0% of the total Hg input, was stored as acid slag in the landfill sites. Approximately 15.0-27.1% of the Hg input was emitted into water or stored as open-dumped slags, and 3.3-14.5% of the Hg input ended in sulfuric acid. Atmospheric Hg emissions, accounting for 1.4-9.6% of the total Hg input, were from both the Zn production and waste disposal processes. Atmospheric Hg emissions from the waste disposal processes accounted for 40.6, 89.6, and 94.6% of the total atmospheric Hg emissions of the three studied smelters, respectively. The Zn production process mainly contributed to oxidized Hg (Hg2+) emissions, whereas the waste disposal process generated mostly elemental Hg (Hg0) emissions. When the emissions from these two processes are considered together, the emission proportion of the Hg2+ mass was 51, 46, and 29% in smelters A, B, and C, respectively. These results indicated that approximately 10.8±5.8 t of atmospheric Hg emissions from the waste disposal process were ignored in recent inventories. Therefore, the total atmospheric Hg emissions from the Zn industry of China should be approximately 50 t.

Influences of smelter fumes upon the chemical composition of lake waters near Sudbury, Ontario, and upon the surrounding vegetation

Energy Technology Data Exchange (ETDEWEB)

Gorham, E; Gordon, A G

1960-01-01

Analyses for sulphate, calcium, and pH have been made on surface waters from 102 lakes and ponds in the Sudbury metal-smelting district, and data are presented for 35 of these. Sulphur pollution is frequently high within about 5 miles of the three smelters, many ponds exhibiting more than three times the sulphate concentration normal for this area, and three waters more than 10 times this level. Outside about 15 miles distance the influence of smelter pollution upon sulphate concentrations in surface waters is negligible. As expected, many of the most polluted waters are strongly acid, with pH values going as low as 3.3. Sulphuric acid from air pollution has also led to increased weathering of calcium from soils and rocks, so that this ion tends to rise in concentration not only in waters above pH 6 (as expected) but also in those below pH 5. Damage to terrestrial vegetation is frequently marked within about 5 miles of the smelters, while it is seldom obvious to the untrained eye beyond this distance. Severe damage occurs chiefly within about 2 miles of the smelters.

Spatial distribution and risk assessment of heavy metals in soil near a Pb/Zn smelter in Feng County, China.

Science.gov (United States)

Shen, Feng; Liao, Renmei; Ali, Amjad; Mahar, Amanullah; Guo, Di; Li, Ronghua; Xining, Sun; Awasthi, Mukesh Kumar; Wang, Quan; Zhang, Zengqiang

2017-05-01

A large scale survey and a small scale continuous monitoring was conducted to evaluate the impact of Pb/Zn smelting on soil heavy metals (HMs) accumulation and potential ecological risk in Feng County, Shaanxi province of China. Soil parameters including pH, texture, CEC, spatial and temporal distribution of HMs (Cd, Cu, Ni, Pb and Zn), and BCR fractionation were monitored accordingly. The results showed the topsoil in the proximity of smelter, especially the smelter area and county seat, were highly polluted by HMs in contrast to the river basins. Fractionation of Cd and Zn in soil samples revealed higher proportion of mobile fractions than other HMs. The soil Cd and Zn contents decreased vertically, but still exceeded the second level limits of Environmental Quality Standard for Soils of China (EQSS) within 80cm. The dominated soil pollutant (Cd) had higher ecological risk than Cu, Ni, Zn and Pb. The potential ecological risk (PER) factor of Cd were 65.7% and 100% in surrounding county and smelter area, respectively. The long-term smelter dust emission mainly contributed to the HMs pollution and posed serious environment risk to living beings. Copyright © 2017 Elsevier Inc. All rights reserved.

Internal friction in iron-aluminium alloys having a high aluminium content

International Nuclear Information System (INIS)

Hillairet, J.; Delaplace, J.; Silvent, A.

1966-01-01

By using a torsion pendulum to measure the internal friction of iron-aluminium alloys containing between 25 and 50 atom per cent of aluminium, it has been possible to show the existence of three damping peaks due to interstitial carbon. Their evolution is followed as a function of the carbon content, of the thermal treatment and of the aluminium content. A model based on the preferential occupation of tetrahedral sites is proposed as an interpretation of the results. A study of the Zener peak in these substitution alloys shows also that a part of the short distance disorder existing at high temperatures can be preserved by quenching. (author) [fr

The Influence of Tool Geometry towards Cutting Performance in Machining Aluminium 7075

Directory of Open Access Journals (Sweden)

Muhammad Syafik Jumali

2017-01-01

Full Text Available Aerospace industries often use Computer Numerical Control (CNC machining in manufacturing aerospace parts. Aluminium 7075 is the most common material used as aircraft components. This research aims to produce end mill with optimum geometry in terms of the helix angle, primary radial relief angle and secondary relief angle. End mills with different geometry parameters are tested on Aluminium 7075 and data on surface roughness and tool wear were collected. The results were then analysed to determine which parameters brought the optimum result with regards to surface roughness and tool wear.

Aluminium localization and toxicity symptoms related to root growth ...

Indian Academy of Sciences (India)

We correlated root growth inhibition with aluminium (Al3+) localization and toxicity symptoms in rice roots using seedlings of two genotypes (tolerant and sensitive) that were exposed to different AlCl3 concentrations. Al3+ localization was evaluated by hematoxylin in primary roots and by morin in cross-sections of the root ...

The determination of trace oxygen in aluminium and aluminium-silicon alloy by helium-3 activation analysis

International Nuclear Information System (INIS)

Vandecasteele, C.; Goethals, P.; Kieffer, R.; Hoste, J.

1975-01-01

The determination of oxygen in aluminium and aluminium-silicon alloy by helium-3 activation is studied. The 18 F formed from oxygen is separated by distillation followed by precipitation of leadfluorochloride. The chemical yield is determined by activation in an isotopic neutron source. Concentrations of resp. 27 and 64 ng.g -1 with a precision for a single determination of resp. 30 and 13% are found in 99.5% aluminium and in aluminium-silicon (3%) alloy. (author)

Roll bonding of strained aluminium

DEFF Research Database (Denmark)

Staun, Jakob M.

2003-01-01

This report investigates roll bonding of pre-strained (å ~ 4) aluminium sheets to produce high strain material from high purity aluminium (99.996%) and commercial pure aluminium (99.6%). The degree of bonding is investigated by optical microscopy and ultrasonic scanning. Under the right...... of the cross rolled volume fraction is found. To further asses this effect, and the anisotropy, it is necessary to acquire knowledge about both texture and microstructure, e.g. by TEM. Roll bonding of pre-strained aluminium is found to be a possible alternative to ARB in the quest for ultra-fine grained...

Aluminium in foodstuffs and diets in Sweden.

Science.gov (United States)

Jorhem, L; Haegglund, G

1992-01-01

The levels of aluminium have been determined in a number of individual foodstuffs on the Swedish market and in 24 h duplicate diets collected by women living in the Stockholm area. The results show that the levels in most foods are very low and that the level in vegetables can vary by a factor 10. Beverages from aluminium cans were found to have aluminium levels not markedly different from those in glass bottles. Based on the results of the analysis of individual foods, the average Swedish daily diet was calculated to contain about 0.6 mg aluminium, whereas the mean content of the collected duplicate diets was 13 mg. A cake made from a mix containing aluminium phosphate in the baking soda was identified as the most important contributor of aluminium to the duplicate diets. Tea and aluminium utensils were estimated to increase the aluminium content of the diets by approximately 4 and 2 mg/day, respectively. The results also indicate that a considerable amount of aluminium must be introduced from other sources.

Constructions of aluminium electrolytic cells

International Nuclear Information System (INIS)

Galushkin, N.V.

1995-01-01

This chapter of monograph is devoted to constructions of aluminium electrolytic cells. Therefore, the general characteristic and classification of aluminium electrolytic cells was considered. The anode and cathode structure was studied. The lining of cathode casing, the process of collection of anode gases, electrolytic cell cover, and electrical insulation was studied as well. The installation and dismantling of aluminium electrolytic cells was described.

Environmental screening of novel technologies to increase material circularity: A case study on aluminium cans

DEFF Research Database (Denmark)

Stotz, Philippe Maurice; Niero, Monia; Bey, Niki

2017-01-01

It is undisputed that the recycling of aluminium is desirable as long as the environmental and economic implications of its reintegration do not exceed the burdens of its primary production. The efficiency of any aluminium recycling system can be expressed by the total material losses throughout...... the entire process chain, ideally reaching 0%, thus equivalent to 100% metal recovery. However, in most cases metals are recycled in open/cascade recycling loop where dilution and quality losses occur. Innovations in aluminium beverage can (ABC) design as well as in sorting and recycling technologies have......-related impact categories show the highest susceptibility to increasing recycled content and recycling rate, while the technological novelties show little effect. In terms of abiotic resource depletion the introduction of novel technologies could have the potential to retain quality of the aluminium alloys...

Bioindication of air pollution effects near a copper smelter in Brazil using mango trees and soil microbiological properties

International Nuclear Information System (INIS)

Klumpp, Andreas; Hintemann, Therese; Santana Lima, Josanidia; Kandeler, Ellen

2003-01-01

A field study near the copper smelter of a large industrial complex examined air pollution effects on vegetation and soil parameters in Camacari (northeast Brazil). Close to the smelter, soil pH-value was lower and total acidity as well as organic carbon contents were higher compared with a site far from the source and two reference sites. The acidification of top soil particularly and the drastically enhanced plant-available copper concentrations were caused by atmospheric deposition. High sulphur and copper deposition significantly reduced microbial biomass and altered functional diversity of soil microorganisms (arylsulphatase and xylanase). Large accumulations of sulphur, arsenic and copper were detected in mango leaves (Mangifera indica) growing downwind from the smelter suggesting potential food chain-mediated risk. - Atmospheric emissions in northeast Brazil have transformed soil pH, accumulated in soil and plants as sulphur and heavy metals, and affected the functional diversity of soil microorganisms

Bioindication of air pollution effects near a copper smelter in Brazil using mango trees and soil microbiological properties

Energy Technology Data Exchange (ETDEWEB)

Klumpp, Andreas; Hintemann, Therese; Santana Lima, Josanidia; Kandeler, Ellen

2003-12-01

A field study near the copper smelter of a large industrial complex examined air pollution effects on vegetation and soil parameters in Camacari (northeast Brazil). Close to the smelter, soil pH-value was lower and total acidity as well as organic carbon contents were higher compared with a site far from the source and two reference sites. The acidification of top soil particularly and the drastically enhanced plant-available copper concentrations were caused by atmospheric deposition. High sulphur and copper deposition significantly reduced microbial biomass and altered functional diversity of soil microorganisms (arylsulphatase and xylanase). Large accumulations of sulphur, arsenic and copper were detected in mango leaves (Mangifera indica) growing downwind from the smelter suggesting potential food chain-mediated risk. - Atmospheric emissions in northeast Brazil have transformed soil pH, accumulated in soil and plants as sulphur and heavy metals, and affected the functional diversity of soil microorganisms.

Interpreting major industrial landscapes: Social follow-up on meanings, the case of two aluminium smelters, Alcan (Alma, Canada) and Pechiney (Dunkirk, France)

International Nuclear Information System (INIS)

Fortin, Marie-Jose; Gagnon, Christiane

2006-01-01

Landscape is becoming an object of growing social concern and, as such, an object of mediation between major industrial producers and local communities. The question of the capacity of environmental assessment to address this issue is thus raised. Until now, landscape studies have focused on visual aspects, although subjective dimensions such as perceptions and meanings have been recognised. The research in this article concerns the subjective dimensions, and is presented with a view to further the understanding of the process of the social interpretation of landscape as it relates to heavy industrial sites. Within a socioconstructivist perspective, two case studies (a longitudinal follow-up and an ex-post) of two aluminum smelters, one in Alma (Quebec, Canada) and the other in Dunkirk (France) were conducted. The results show that nearby residents' interpretations of landscape varied according to three sets of factors related to 1) the dynamics of regional development and the historical place of industry in the community, 2) the relationship between residents and the industry and local governance capacities, and 3) the social impacts experienced. To conclude, three ways of using qualitative methodologies for social and environmental follow-up in a socioconstructivist approach to landscape are proposed

Biological monitoring of exposure to polycyclic aromatic hydrocarbons among people living nearby an aluminium smelter in the province of Quebec; Surveillance biologique de l'exposition aux hydrocarbures aromatiques polycycliques chez des personnes vivant aux environs d'une aluminerie quebecoise

Energy Technology Data Exchange (ETDEWEB)

Saint-Amour, M.; Tremblay, C.; Jacques, L. [Direction de la Sante Publique de la Monteregie, Quebec (Canada); Weber, J.P. [Centre de Toxicologie du Quebec (Canada)

2000-10-01

The objective of the study is to estimate the exposure to pyrene, an indicator of polycyclic aromatic hydrocarbons (PAHs) in the general, environment, by using the internal dose of 1-hydroxy-pyrene (1-OHP) among people living nearby an aluminium smelter in the Monteregie area, Province of Quebec, Canada.This cross-sectional study was done in November and December 1998. Participants were randomly selected according to their environmental exposure to PAHs and were distributed according to three exposure levels (high, low, none). Altogether, 121 non smokers aged between 18 to 70 years were recruited for the study. Persons occupationally exposed to PAHs or using tar-based medications were excluded. Those with personal medical conditions that affect the metabolism of pyrene were also excluded. Urine samples were taken in the morning and analysed by gas chromatography and mass spectrometry (GC-MS) to determine the concentration of the metabolite, 1-OHP. Among the exposed group (n=78), the geometric mean of urinary concentration of 1-OHP was 0.073 {mu}mol/mol creatinine compared to 0.060 {mu}mol/mol creatinine for the control group (n=40). The difference did not reach statistical significance (p=0.09, 0.067 and 0.060 {mu}mol/mol creatinine p=0.13). Accounting for personal risk factors, such as diet, passive smoke, use of wood heating and time spent at home during the three days prior to urine sampling, did not change previous results. This study indicates that the environmental levels of PAH produced by this factory are low and do not contribute significantly to be body burden of PAH as measured by 1-OHP. (authors)

Determination of aluminium in groundwater samples by GF-AAS, ICP-AES, ICP-MS and modelling of inorganic aluminium complexes.

Science.gov (United States)

Frankowski, Marcin; Zioła-Frankowska, Anetta; Kurzyca, Iwona; Novotný, Karel; Vaculovič, Tomas; Kanický, Viktor; Siepak, Marcin; Siepak, Jerzy

2011-11-01

The paper presents the results of aluminium determinations in ground water samples of the Miocene aquifer from the area of the city of Poznań (Poland). The determined aluminium content amounted from aluminium determinations were performed using three analytical techniques: graphite furnace atomic absorption spectrometry (GF-AAS), inductively coupled plasma atomic emission spectrometry (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS). The results of aluminium determinations in groundwater samples for particular analytical techniques were compared. The results were used to identify the ascent of ground water from the Mesozoic aquifer to the Miocene aquifer in the area of the fault graben. Using the Mineql+ program, the modelling of the occurrence of aluminium and the following aluminium complexes: hydroxy, with fluorides and sulphates was performed. The paper presents the results of aluminium determinations in ground water using different analytical techniques as well as the chemical modelling in the Mineql+ program, which was performed for the first time and which enabled the identification of aluminium complexes in the investigated samples. The study confirms the occurrence of aluminium hydroxy complexes and aluminium fluoride complexes in the analysed groundwater samples. Despite the dominance of sulphates and organic matter in the sample, major participation of the complexes with these ligands was not stated based on the modelling.

[Association between serum aluminium level and methylation of amyloid precursor protein gene in workers engaged in aluminium electrolysis].

Science.gov (United States)

Yang, X J; Yuan, Y Z; Niu, Q

2016-04-20

To investigate the association between serum aluminium level and methylation of the promoter region of amyloid precursor protein (APP)gene in workers engaged in aluminium electrolysis. In 2012, 366 electrolysis workers in an aluminium factory were enrolled as exposure group (working years >10 and age >40 years)and divided into low-exposure group and high-exposure group based on the median serum aluminium level. Meanwhile, 102 workers in a cement plant not exposed to aluminium were enrolled as control group. Graphite furnace atomic absorption spectrometry was used to measure serum aluminium level, methylation specific PCR was used to measure the methylation rate of the promoter region of APP gene, and ELI-SA was used to measure the protein expression of APP in lymphocytes in peripheral blood. The exposure group had a significantly higher serum aluminium level than the control group (45.07 μg/L vs 30.51 μg/L, P0.05). The multivariate logistic regression analysis showed that with reference to the control group, low aluminium exposure (OR=1.86, 95% CI 1.67~3.52)and high aluminium exposure (OR=2.98, 95% CI 1.97~4.15)were risk factors for a reduced methylation rate of the promoter region of APP gene. Reduced methylation of the promoter region of APP gene may be associated with increased serum aluminium level, and downregulated methylation of the promoter region of APP gene may accelerate APP gene transcription.

Bumblebee pupae contain high levels of aluminium.

Science.gov (United States)

Exley, Christopher; Rotheray, Ellen; Goulson, David

2015-01-01

The causes of declines in bees and other pollinators remains an on-going debate. While recent attention has focussed upon pesticides, other environmental pollutants have largely been ignored. Aluminium is the most significant environmental contaminant of recent times and we speculated that it could be a factor in pollinator decline. Herein we have measured the content of aluminium in bumblebee pupae taken from naturally foraging colonies in the UK. Individual pupae were acid-digested in a microwave oven and their aluminium content determined using transversely heated graphite furnace atomic absorption spectrometry. Pupae were heavily contaminated with aluminium giving values between 13.4 and 193.4 μg/g dry wt. and a mean (SD) value of 51.0 (33.0) μg/g dry wt. for the 72 pupae tested. Mean aluminium content was shown to be a significant negative predictor of average pupal weight in colonies. While no other statistically significant relationships were found relating aluminium to bee or colony health, the actual content of aluminium in pupae are extremely high and demonstrate significant exposure to aluminium. Bees rely heavily on cognitive function and aluminium is a known neurotoxin with links, for example, to Alzheimer's disease in humans. The significant contamination of bumblebee pupae by aluminium raises the intriguing spectre of cognitive dysfunction playing a role in their population decline.

Composition and fate of mine- and smelter-derived particulates in soils from humid subtropical and semiarid areas

Science.gov (United States)

Ettler, Vojtech; Kribek, Bohdan; Mihaljevic, Martin; Vanek, Ales; Penizek, Vit; Sracek, Ondra; Mapani, Ben; Kamona, Fred; Nyambe, Imasiku

2017-04-01

Soils in the vicinity of non-ferrous metal smelters are often highly polluted by inorganic contaminants released from particulate emissions, which undergo weathering processes and release contaminants when deposited in soils. We studied the heavy mineral fraction, separated from mining- and smelter-affected topsoils, from both a humid subtropical area in the Zambian Copperbelt and a hot semi-arid area in the northern Namibia. High concentrations of metal(loid)s were detected in the studied soils: up to 1450 ppm As, 8980 ppm Cu, 4640 ppm Pb, 2620 ppm Zn. A combination of X-ray diffraction analysis (XRD), scanning electron microscopy (SEM/EDS), and electron probe microanalysis (EPMA) helped to identify the phases forming individual metal(loid)-bearing particles. Whereas spherical particles originate from the smelting and flue gas cleaning processes, angular particles either have geogenic origins or they are windblown from the mining operations and mine waste disposal sites. Sulphides from ores and mine tailings often exhibit weathering rims in contrast to smelter-derived high-temperature sulphides (chalcocite [Cu2S], digenite [Cu9S5], covellite [CuS], non-stoichiometric quenched Cu-Fe-S phases). Soils from humid subtropical areas exhibit higher available concentrations of metal(loids), and higher frequencies of weathering features (especially for copper-bearing oxides such as delafossite [CuFeO2]) are observed. In contrast, metal(loid)s are efficiently retained in semi-arid soils, where a high proportion of non-weathered smelter slag particles and low-solubility Ca-Cu-Pb arsenates occur. Our results indicate that compared to semi-arid areas (where inorganic contaminants were rather immobile in soils despite their high concentrations) a higher potential risk exists for agriculture in mine- and smelter-affected humid subtropical areas (where metal(loid) contaminants can be highly available for the uptake by crops). This study was supported by the Czech Science

Long-term effects of aluminium dust inhalation.

Science.gov (United States)

Peters, Susan; Reid, Alison; Fritschi, Lin; de Klerk, Nicholas; Musk, A W Bill

2013-12-01

During the 1950s and 1960s, aluminium dust inhalation was used as a potential prophylaxis against silicosis in underground miners, including in Australia. We investigated the association between aluminium dust inhalation and cardiovascular, cerebrovascular and Alzheimer's diseases in a cohort of Australian male underground gold miners. We additionally looked at pneumoconiosis mortality to estimate the effect of the aluminium therapy. SMRs and 95% CI were calculated to compare mortality of the cohort members with that of the Western Australian male population (1961-2009). Internal comparisons on duration of aluminium dust inhalation were examined using Cox regression. Aluminium dust inhalation was reported for 647 out of 1894 underground gold miners. During 42 780 person-years of follow-up, 1577 deaths were observed. An indication of increased mortality of Alzheimer's disease among miners ever exposed to aluminium dust was found (SMR=1.38), although it was not statistically significant (95% CI 0.69 to 2.75). Rates for cardiovascular and cerebrovascular death were above population levels, but were similar for subjects with or without a history of aluminium dust inhalation. HRs suggested an increasing risk of cardiovascular disease with duration of aluminium dust inhalation (HR=1.02, 95% CI 1.00 to 1.04, per year of exposure). No difference in the association between duration of work underground and pneumoconiosis was observed between the groups with or without aluminium dust exposure. No protective effect against silicosis was observed from aluminium dust inhalation. Conversely, exposure to aluminium dust may possibly increase the risk of cardiovascular disease and dementia of the Alzheimer's type.

The influence of the intensity of smoking and years of work in the metallurgy on pro-oxidant/antioxidant balance in the blood of smelters.

Science.gov (United States)

Bizon, Anna; Antonowicz-Juchniewicz, Jolanta; Andrzejak, Ryszard; Milnerowicz, Halina

2013-03-01

The aim of this study was to investigate the effect of cigarette smoking and occupational exposure to heavy metals on the degree of pro-oxidant/antioxidant imbalance in smelters. The investigations were performed on the blood and urine of 400 subjects: 300 male copper smelters and 100 nonexposed male subjects. Biological material was divided into three groups: nonsmokers, those who smoked less than 20 cigarettes a day and those who smoked more than 20 cigarettes a day. The results showed a significant increase in the concentration of lead, cadmium and arsenic in the blood and urine of smelters, while smoking more than 20 cigarettes a day caused a further increase in the concentration of these metals. The level of malondialdehyde was approximately twofold higher in the plasma of the smelters compared to the control group. We have observed a disturbance in the level of antioxidants in erythrocyte lysate manifested by an increase in metallothionein and glutathione concentrations as well as superoxide dismutase and glutathione peroxidase activities and the decrease in glutathione S-transferase activity. Cigarette smoking, years of work in metallurgy and age of smelters were additional factors significantly affecting the pro-oxidant/antioxidant balance.

Mapping airborne lead contamination near a metals smelter in Derbyshire, UK: spatial variation of Pb concentration and 'enrichment factor' for tree bark.

Science.gov (United States)

Bellis, D; Cox, A J; Staton, I; McLeod, C W; Satake, K

2001-10-01

Samples of tree bark, collected over an area of 4 km2 near a small non-ferrous metals smelter in Derbyshire, UK, were analysed for Pb and Al by inductively coupled plasma atomic emission spectroscopy (ICP-AES). Analyte concentrations varied from 100 to over 25,000 mg kg-1 and 5 to 1000 mg kg-1, respectively. While an inverse relationship between the Pb content of bark and distance from the smelter was observed, concentrations fluctuated, indicating a variability in sample collection efficiency and problems in standardization. To overcome these effects, the Pb/Al ratio was calculated and subsequently normalized to the average Pb/Al ratio in continental crust (0.00015). On the assumption that the time-averaged concentration of airborne Al in this area is relatively constant and derived principally from wind-blown soil, the measurement represents an anthropogenic 'enrichment factor' (PbEF). PbEF varied from 10,000 to over 1,000,000, and showed a consistent reduction with distance from the smelter. Isolines of equal PbEF were subsequently defined on a map of the sampled area. Pb contamination was greatest in the vicinity of the smelter, and preferential transport along the NW-SE axis of the valley (in which the smelter is situated) was observed. The use of enrichment factors thus proved valuable in defining the relative level of airborne-derived Pb pollution.

Design and analysis of aluminium brdiges

NARCIS (Netherlands)

Soetens, F.; Straalen, IJ.J. van

2004-01-01

Applications of aluminium have grown considerably in building and civil engineering the last decade, which is due to various aspects: light weight, durability and maintenance, use of extrusions. The paper starts with a short history of aluminium bridges and then focuses on aluminium bridges in the

Heavy metal tolerance in Agropyron repens (L. P. Bauv. populations from the Legnica copper smelter area, Lower Silesia

Directory of Open Access Journals (Sweden)

Teresa Brej

2014-01-01

Full Text Available The copper smelter "Legnica" is one of the oldest plants in Lower Silesia. Among the few weed species spontaneously migrating to the area around the emitter there is couch grass (Agropyron repens (L. P. Bauv.. The purpose of this study was to analyse whether the local couch grass populations, growing at various distances from the smelter, differ in tolerance to heavy metals occurring in this area. The populations were tested for tolerance to five metals (Cu, Zn, Pb, Cd, Ni using the root elongation method. The highest tolerance to Pb developed in two populations localized nearest the smelter. Similarly, all populations of couch grass from the vicinity of the smelter show a high tolerance to copper, particularly the plants from the most contaminated site. The IT for the latter population is almost 1509r, even at the highest dose of Cu. For Zn a nearing IT as for Cu was obtained. Comparing the shape of IT curves for Cd, special emphasis is put on the fact that a fixed tolerance to cadmium occurs only in the population localized closest to the emitter. The analysis of Ni-tolerance curves, of which the content in local soil is minimal, does not confirm the thesis on possibility of development of co-tolerance in the surveyed populations. It appeared that stress conditions existing near the smelter do not inhibit seed production in couch grass, but prevent a successful course of their germination on polluted soil. The improvement of soil even by 50% (addition of unpolluted soil does not improve the poor process of germination in couch grass growing nearest to the smelter. Of importance is the fact that the highest number of seeds germinated on their own, polluted soil. The need of metals' content for plant germination in populations most distant from the smelter is evidenced by an almost 30% reduction of germination ability of local seeds after addition of unpolluted soil. Another significant observation was the fact that, in spite of a poor

Intersampler field comparison of Respicon(R), IOM, and closed-face 25-mm personal aerosol samplers during primary production of aluminium.

Science.gov (United States)

Skaugset, Nils Petter; Ellingsen, Dag G; Notø, Hilde; Jordbekken, Lars; Thomassen, Yngvar

2013-10-01

Intersampler field comparison of Respicon(®), 25-mm closed-face 'total dust' cassette (CFC), and IOM inhalable aerosol sampler was conducted in pot rooms at seven aluminium smelters. The aerosol mass and water-soluble fluoride were selected as airborne contaminants for the comparisons. The aerosol masses of 889 sample pairs of IOM and Respicon(®) inhalable aerosol sub-fraction, 165 of IOM and 25-mm CFC, and 194 of CFC and Respicon(®) thoracic aerosol sub-fraction were compared. The number of sample pairs for the comparison of water-soluble fluoride was 906, 170, and 195, respectively. The geometric mean aerosol mass collected with the inhalable Respicon(®) was 2.91 mg m(-3) compared with 3.38 mg m(-3) with the IOM. The overall ratio between IOM and Respicon(®) inhalable sub-fraction was 1.16 [95% confidence interval (CI) = 1.11-1.21] for aerosol mass and 1.13 (95% CI = 1.08-1.18) for water-soluble fluoride. The results indicate that Respicon(®) undersampled the aerosol mass and water-soluble fluoride in the inhalable sub-fraction compared with the IOM. The results indicated undersampling of the Respicon(®) at mass concentrations higher than 1.35 mg m(-3) and oversampling at lower mass concentrations. The overall ratio between aerosol mass collected with IOM and CFC was 4.19 (95% CI = 3.79-4.64) and 1.61 (95% CI = 1.51-1.72) for water-soluble fluoride. Thus, for this industry, a correction factor of 4.2 is suggested for the conversion of CFC to inhalable aerosol masses and a conversion factor of 1.6 for water-soluble fluoride if wall deposits in the CFC are included. CFC and thoracic Respicon(®) collected similar aerosol masses (ratio = 1.04; 95% CI = 0.97-1.12), whereas the ratio was 1.19 (95% CI = 1.11-1.28) for water-soluble fluoride. The variability of the exposure is substantial; thus, large data sets are required in sampler performance field comparisons.

Food chain transfer of cadmium and lead to cattle in a lead-zinc smelter in Guizhou, China

International Nuclear Information System (INIS)

Cai Qiu; Long Meili; Zhu Ming; Zhou Qingzhen; Zhang Ling; Liu Jie

2009-01-01

Cadmium (Cd) and Lead (Pb) are environmental pollutants. Environmental samples and bovine tissues were collected from the areas around a lead-zinc smelter in Guizhou, China for Cd, Pb, zinc (Zn) and copper (Cu) analysis. Cd in soil (10 mg/kg) and feed (6.6 mg/kg) from the polluted areas was 10 times higher than the Chinese Standards, resulting in higher Cd in bovine kidney (38 mg/kg) and liver (2.5 mg/kg). Pb in feed (132 mg/kg) from the polluted area was much higher than unpolluted areas, causing higher Pb levels in bovine tissues. Environmental Zn was elevated, but bovine tissue Zn was normal. Cu in bovine liver decreased with increased Cd and Pb. Metals in drinking water and in bovine muscle were within the Standard range. Thus, in the areas of this lead-zinc smelter, the environment has been contaminated with Cd and Pb, which has been transferred to cattle through the food chain. - Cd and Pb from lead-zinc smelters contaminate the environment and accumulate in bovine tissues.

Recycling of aluminium swarf by direct incorporation in aluminium melts

OpenAIRE

Puga, Hélder; Barbosa, J.; Soares, Delfim; Silva, Filipe Samuel; Ribeiro, Carlos Silva

2009-01-01

The purpose of this work was to recover a standard AlSi12Cu1 alloy from machining chips inside the foundry plant, by using an environmentally friend technique to produce cast ingots with characteristics similar to those of the commercially available 2nd melt raw material. The recyclability of aluminium swarf using different melting techniques and the influence of chips preparation in the aluminium alloy recovery rate and dross production was experimentally studied and evaluated...

Irradiation damage in aluminium single crystals produced by 50-keV aluminium and copper ions

DEFF Research Database (Denmark)

Henriksen, L.; Johansen, A.; Koch, J.

1968-01-01

Aluminium single crystals, thin enough to be examined by electron microscopy, have been irradiated with 50-keV aluminium and copper ions. The irradiation fluxes were in the range 1011–1014 cm−2 s−1 and the doses were from 6 × 1012 to 6 × 1014 cm−2. Irradiation along either a or a direction produces...... rows of dislocation loops all lying parallel to one particular direction. If the aluminium target is quenched from 600 °C and annealed at room temperature prior to irradiation with aluminium ions, the rows of loops are suppressed. The amount of damage observed is considerably less than would...

78 FR 33409 - Proposed Information Collection Request; Comment Request; See Item Specific ICR Titles Provided...

Science.gov (United States)

2013-06-04

... Production (40 CFR Part 60, Subpart M), Primary Copper Smelters (40 CFR Part 60, Subpart P), Primary Zinc... bronze production facilities, primary copper smelters, primary zinc smelters, primary lead smelters... ID Number: EPA-HQ-OECA-2013-0314; Title: NSPS for Phosphate Rock Plants (40 CFR Part 60, Subpart NN...

Effect of aluminium on migratory and invasive properties of MCF-7 human breast cancer cells in culture.

Science.gov (United States)

Darbre, Philippa D; Bakir, Ayse; Iskakova, Elzira

2013-11-01

Aluminium (Al) has been measured in human breast tissue, nipple aspirate fluid and breast cyst fluid, and recent studies have shown that at tissue concentrations, aluminium can induce DNA damage and suspension growth in human breast epithelial cells. This paper demonstrates for the first time that exposure to aluminium can also increase migratory and invasive properties of MCF-7 human breast cancer cells. Long-term (32 weeks) but not short-term (1 week) exposure of MCF-7 cells to 10(-4) M aluminium chloride or 10(-4) M aluminium chlorohydrate increased motility of the cells as measured by live cell imaging (cumulative length moved by individual cells), by a wound healing assay and by migration in real time through 8 μm pores of a membrane using xCELLigence technology. Long-term exposure (37 weeks) to 10(-4) M aluminium chloride or 10(-4) M aluminium chlorohydrate also increased the ability of MCF-7 cells to invade through a matrigel layer as measured in real time using the xCELLigence system. Although molecular mechanisms remain to be characterized, the ability of aluminium salts to increase migratory and invasive properties of MCF-7 cells suggests that the presence of aluminium in the human breast could influence metastatic processes. This is important because mortality from breast cancer arises mainly from tumour spread rather than from the presence of a primary tumour in the breast. © 2013.

Laser welding of aluminium alloys

OpenAIRE

Forsman, Tomas

2000-01-01

This thesis treats laser welding of aluminium alloys from a practical perspective with elements of mathematical analysis. The theoretical work has in all cases been verified experimentally. The aluminium alloys studied are from the 5xxx and 6xxx groups which are common for example in the automotive industry. Aluminium has many unique physical properties. The properties which more than others have been shown to influence the welding process is its high reflection, high thermal conductivity, lo...

Contrasting isotopic signatures between anthropogenic and geogenic Zn and evidence for post-depositional fractionation processes in smelter-impacted soils from Northern France

Science.gov (United States)

Juillot, Farid; Maréchal, Chloe; Morin, Guillaume; Jouvin, Delphine; Cacaly, Sylvain; Telouk, Philipe; Benedetti, Marc F.; Ildefonse, Philippe; Sutton, Steve; Guyot, François; Brown, Gordon E., Jr.

2011-05-01

Zinc isotopes have been studied along two smelter-impacted soil profiles sampled near one of the largest Pb and Zn processing plants in Europe located in northern France, about 50 km south of Lille. Mean δ 66Zn values along these two soil profiles range from +0.22 ± 0.17‰ (2 σ) to +0.34 ± 0.17‰ (2 σ) at the lowest horizons and from +0.38 ± 0.45‰ (2 σ) to +0.76 ± 0.14‰ (2 σ) near the surface. The δ 66Zn values in the lowest horizons of the soils are interpreted as being representative of the local geochemical background (mean value +0.31 ± 0.38‰), whereas heavier δ 66Zn values near the surface of the two soils are related to anthropogenic Zn. This anthropogenic Zn occurs in the form of franklinite (ZnFe 2O 4)-bearing slag grains originating from processing wastes at the smelter site and exhibiting δ 66Zn values of +0.81 ± 0.20‰ (2 σ). The presence of franklinite is indicated by EXAFS analysis of the topsoil samples from both soil profiles as well as by micro-XANES analysis of the surface horizon of a third smelter-impacted soil from a distant site. These results indicate that naturally occurring Zn and smelter-derived Zn exhibit significantly different δ 66Zn values, which suggests that zinc isotopes can be used to distinguish between geogenic and anthropogenic sources of Zn in smelter-impacted soils. In addition to a possible influence of additional past sources of light Zn (likely Zn-sulfides and Zn-sulfates directly emitted by the smelter), the light δ 66Zn values in the surface horizons compared to smelter-derived slag materials are interpreted as resulting mainly from fractionation processes associated with biotic and/or abiotic pedological processes (Zn-bearing mineral precipitation, Zn complexation by organic matter, and plant uptake of Zn). This conclusion emphasizes the need for additional Zn isotopic studies before being able to use Zn isotopes to trace sources and pathways of this element in surface environments.

Process for the manufacture of plates containing neutron poison from aluminium and aluminium alloys

International Nuclear Information System (INIS)

Bauer, G.; Pollmann, E.; Srostlik, P.

1985-01-01

A process for guaranteeing sub-critical arrangements of nuclear fuel in tranport and/or storage containers is described, in which a homogeneous distribution of neutron poison in the aluminium matrix is guaranteed. A homogeneous mixture of aluminium powder and neutron poison powder is produced, this is pressed into plates in several stages, dried and made into hollow aluminium profiles of rectangular cross-section. The open ends of the hollow profile are then closed and this is rolled to the required dimension at 470-500 0 C. (orig./HP) [de

Chapter 1. Economic aspects of aluminium production

International Nuclear Information System (INIS)

Yanko, E.A.; Kabirov, Sh.O.; Safiev, Kh.; Azizov, B.S.; Mirpochaev, Kh.A.

2011-01-01

This article is devoted to economic aspects of aluminium production. Therefore, the perspectives of development of aluminium production, the base components of aluminium cost and economic security of enterprise are considered in this chapter.

Ductile failure in upsetting of a rapid-solidification-processed aluminium alloy

NARCIS (Netherlands)

Habraken, F.A.C.M.; Dautzenberg, J.H.

1993-01-01

Cold upset-tests have been performed on a Rapid Solidification Processed (RSP) aluminium-alloy, produced by the ‘melt-spun ribbons’-process out of 70% car-scrap and 30% primary scrap. The ribbons are hot extruded, resulting in 29 mm diameter bar. Its properties regarding plastic flow and fracture

Aluminium and nickel in human albumin solutions

DEFF Research Database (Denmark)

Gammelgaard, Bente; Sandberg, E

1989-01-01

Five different brands of commercially available human albumin solutions for infusion were analysed for their aluminium and nickel contents by atomic absorption spectrometry. The aluminium concentrations ranged from 12 micrograms/l to 1109 micrograms/l and the nickel concentrations ranged from 17...... micrograms/l to 77 micrograms/l. Examination of the aluminium and nickel contents of the constituents for the production of one brand showed too low levels to explain the final contamination of the product. By following the aluminium and nickel concentrations of the same brand during the production...... of a batch of albumin solution, filtration was shown to contribute to contamination, although the largest increase in aluminium as well as nickel concentrations appeared during the bulk concentrating process. To avoid health risks to certain patients, regulations should be established requiring aluminium...

Aluminium beverage can recycling

Energy Technology Data Exchange (ETDEWEB)

Lewinski, A von

1985-08-01

Canned beverages have become a controversial issue in this era of ecological sensitivity. METALL has already discussed the problem of can recycling. The present article discusses the technical aspects of aluminium can recycling. Two further articles will follow on aluminium can recycling in North America and on the results of European pilot projects.

Photochemical preparation of aluminium oxide layers via vacuum ultraviolet irradiation of a polymeric hexanoato aluminium complex

International Nuclear Information System (INIS)

Wennrich, L.; Khalil, H.; Bundesmann, C.; Decker, U.; Gerlach, J.W.; Helmstedt, U.; Manova, D.; Naumov, S.; Prager, L.

2013-01-01

By means of photochemical conversion of thin layers of a polymeric hexanoato aluminium complex as the precursor, thin aluminium oxide layers were prepared onto silicon wafers. The precursor compound was synthesized and characterized by several analytical techniques like NMR, FTIR, XPS, ICP, and found to be a polymeric aluminium-containing coordination compound which has been proposed to be a hydroxo-bridged aluminium chain with pendant hexanoyl side-chains ascertained as catena-poly[{di(κ-O,O-hexanoato)aluminium}(μ-hydroxo)] (PHAH). Thin layers deposited from a solution of PHAH in toluene onto silicon wafers were irradiated using VUV radiation from a xenon excimer lamp. The layers were characterized by XPS, XRD, XRR, and spectroscopic ellipsometry. VUV radiation with a radiant exposure of E = 36 J cm −2 led to almost carbon-free amorphous layers with a composition close to that of alumina having a density of about 2.1 g cm −3 . Thus, using the example of a polymeric aluminium complex, the potential of the photochemical conversion of metal complexes into oxides could be shown as an alternative method, in addition to sol–gel techniques, for the generation of thin plane metal-oxide layers at normal temperature and pressure. Highlights: ► A polymeric aluminium complex was synthesized and characterized by NMR, FTIR, XPS and ICP. ► Thin layers of the compound were irradiated using vacuum-UV radiation and converted to AlO x . ► Quantum-chemical calculations explain the conversion mechanism.

Aluminium-27 n.m.r. studies of aluminium fluoro complexes in dichloromethane solution: evidence for tetrafluoroaluminate anion

International Nuclear Information System (INIS)

Colton, R.; Eller, P.G.

1989-01-01

Mixed aluminium chloro/fluoro anions are formed in dichloromethane solution by the interaction of AlCl 3 and [Ph 3 PhCH 2 P] [H 2 F 3 ]. Aluminium-27 n.m.r. studies are restricted to the stoichiometric ranges F/Al from 1:1 to 3:1 and F/Al>8:1. Between these limits rapid precipitation reactions occur. In the fluoride-rich stoichiometric range there is rapid exchange on the n.m.r. time scale between the aluminium fluoro anion and free fluoride, so that a direct identification of the species by the multiplicity of the resonance is not possible. Indirect evidence strongly suggests that the aluminium species is [AlF 4 ] - . In the F/Al stoichiometry range from 1:1 to 3:1 aluminium-27 resonances were observed for all the other possible [AlCl χ F 4-χ ] - species. Studies on the aluminium iodo/fluoro system support the identification of [AlF 4 ] - , but the system is labile and the mixed iodo/fluoro species undergo rapid disproportionation. 12 refs., 1 fig

Effect of hydrogen on aluminium and aluminium alloys: A review

DEFF Research Database (Denmark)

Ambat, Rajan; Dwarakadasa, E.S.

1996-01-01

Susceptibility of aluminium and its alloys towards hydrogen embrittlement has been well established. Still a lot of confusion exists on the question of transport of hydrogen and its possible role in stress corrosion cracking. This paper reviews some of the fundamental properties of hydrogen...... in aluminium and its alloys and its effect on mechanical properties. The importance of hydrogen embrittlement over anodic dissolution to explain the stress corrosion cracking mechanism of these alloys is also examined in considerable detail. The various experimental findings concerning the link between...

Raw materials for aluminium production

International Nuclear Information System (INIS)

Galushkin, N.V.

1995-01-01

This chapter of monograph is devoted to to raw materials which used in aluminium production. Therefore, the using of alumina, and fluoride salts in aluminium production was considered. The physical properties of alumina were studied.

Electron beam welding of aluminium components

International Nuclear Information System (INIS)

Maajid, Ali; Vadali, S.K.; Maury, D.K.

2015-01-01

Aluminium is one of the most widely used materials in industries like transportation, shipbuilding, manufacturing, aerospace, nuclear, etc. The challenges in joining of aluminium are distortion, cleanliness and quality. Main difficulties faced during fusion welding of aluminium components are removal of surface oxide layer, weld porosity, high heat input requirement, distortion, hot cracking, etc. Physical properties of aluminium such as its high thermal conductivity, high coefficient of thermal expansion, no change in colour at high temperature, large difference in the melting points of the metal and its oxide (∼ 1400 °C) compound the difficulties faced during welding. Gas Tungsten Arc Welding (GTAW), Gas Metal Arc Welding (GMAW), Plasma Arc Welding (PAW), etc are generally used in industries for fusion welding of aluminium alloys. However in case of thicker jobs the above processes are not suitable due to requirements of elaborate edge preparation, preheating of jobs, fixturing to prevent distortion, etc. Moreover, precise control over the heat input during welding and weld bead penetration is not possible with above processes. Further, if heat sensitive parts are located near the weld joint then high energy density beam welding process like Electron Beam Welding (EBW) is the best possible choice for aluminium welding.This paper discusses EB welding of aluminium components, typical geometry of components, selection/optimization of welding parameters, problems faced during standardization of welding and process parameters and their remedies etc.

Chapter 2. Theoretical aspects of aluminium production

International Nuclear Information System (INIS)

Yanko, E.A.; Kabirov, Sh.O.; Safiev, Kh.; Azizov, B.S.; Mirpochaev, Kh.A.

2011-01-01

This article is devoted to theoretical aspects of aluminium production. Thus, the electrochemistry of electrolysis process, calculation of base industrial indicators of aluminium electrolytic cell, and processes occurring on anode and cathode were considered. Factors, which increase the current output and electrolytic cell productivity were studied. The side effects, including anode effect, sodium extraction on cathode, aluminium dissolution in the electrolyte, aluminium carbide formation, and influence of admixtures in the electrolyte were studied as well.

Aluminium in brain tissue in familial Alzheimer's disease.

Science.gov (United States)

Mirza, Ambreen; King, Andrew; Troakes, Claire; Exley, Christopher

2017-03-01

The genetic predispositions which describe a diagnosis of familial Alzheimer's disease can be considered as cornerstones of the amyloid cascade hypothesis. Essentially they place the expression and metabolism of the amyloid precursor protein as the main tenet of disease aetiology. However, we do not know the cause of Alzheimer's disease and environmental factors may yet be shown to contribute towards its onset and progression. One such environmental factor is human exposure to aluminium and aluminium has been shown to be present in brain tissue in sporadic Alzheimer's disease. We have made the first ever measurements of aluminium in brain tissue from 12 donors diagnosed with familial Alzheimer's disease. The concentrations of aluminium were extremely high, for example, there were values in excess of 10μg/g tissue dry wt. in 5 of the 12 individuals. Overall, the concentrations were higher than all previous measurements of brain aluminium except cases of known aluminium-induced encephalopathy. We have supported our quantitative analyses using a novel method of aluminium-selective fluorescence microscopy to visualise aluminium in all lobes of every brain investigated. The unique quantitative data and the stunning images of aluminium in familial Alzheimer's disease brain tissue raise the spectre of aluminium's role in this devastating disease. Copyright © 2016 The Authors. Published by Elsevier GmbH.. All rights reserved.

Modelling assessment of regional groundwater contamination due to historic smelter emissions of heavy metals

NARCIS (Netherlands)

Grift, B. van der; Griffioen, J.

2008-01-01

Historic emissions from ore smelters typically cause regional soil contamination. We developed a modelling approach to assess the impact of such contamination on groundwater and surface water load, coupling unsaturated zone leaching modelling with 3D groundwater transport modelling. Both historic

Lactobacillus plantarum CCFM639 alleviates aluminium toxicity.

Science.gov (United States)

Yu, Leilei; Zhai, Qixiao; Liu, Xiaoming; Wang, Gang; Zhang, Qiuxiang; Zhao, Jianxin; Narbad, Arjan; Zhang, Hao; Tian, Fengwei; Chen, Wei

2016-02-01

Aluminium (Al) is the most abundant metal in the earth's crust. Al exposure can cause a variety of adverse physiological effects in humans and animals. Our aim was to demonstrate that specific probiotic bacteria can play a special physiologically functional role in protection against Al toxicity in mice. Thirty strains of lactic acid bacteria (LAB) were tested for their aluminium-binding ability, aluminium tolerance, their antioxidative capacity, and their ability to survive the exposure to artificial gastrointestinal (GI) juices. Lactobacillus plantarum CCFM639 was selected for animal experiments because of its excellent performance in vitro. Forty mice were divided into four groups: control, Al only, Al plus CCFM639, and Al plus deferiprone (DFP). CCFM639 was administered at 10(9) CFU once daily for 10 days, followed by a single oral dose of aluminium chloride hexahydrate at 5.14 mg aluminium (LD50) for each mouse. The results showed that CCFM639 treatment led to a significant reduction in the mortality rates with corresponding decrease in intestinal aluminium absorption and in accumulation of aluminium in the tissues and amelioration of hepatic histopathological damage. This probiotic treatment also resulted in alleviation of hepatic, renal, and cerebral oxidative stress. The treatment of L. plantarum CCFM639 has potential as a therapeutic dietary strategy against acute aluminium toxicity.

Structural evolution in nanoporous anodic aluminium oxide

International Nuclear Information System (INIS)

Rocca, Emmanuel; Vantelon, Delphine; Reguer, Solenn; Mirambet, François

2012-01-01

Nanoporous and self-organized layers of aluminium alloys are used in many applications as membranes, templates for nanometric objects or corrosion protection for aluminium alloys. The use of this nanometric structure widely remains empirical, especially in the case of very small pores ( 4 into AlO 6 cluster and a partial release of sulphate ions are an important chemical transformation of the amorphous structure. This structural transformation defines the chemistry (pH and surface charge) inside the nanopores, the ageing behaviour and the possible incorporation or diffusion of chemical species in the nanostructure. Highlights: ► Investigations of local chemical environment of aluminium atoms in anodic aluminium oxide. ► The oxide structure is constituted by 2/3 of aluminium in tetrahedral coordination 1/3 in octahedral coordination. ► In contact with water, AlO 4 clusters are transformed into AlO 6 cluster and the aluminium sulphate bonds are hydrolysed. ► These transformations induce a pH decrease inside the nanostructure.

Aluminium, gallium, indium and thallium

International Nuclear Information System (INIS)

Brown, Paul L.; Ekberg, Christian

2016-01-01

Aluminium can exist in a number of oxyhydroxide mineral phases including corundum, diaspore, boehmite and gibbsite. The stability constants at zero ionic strength reported for Al(OH) 3 (aq) vary linearly with respect to the inverse of absolute temperature. A full suite of thermodynamic parameters is available for all aluminium phases and hydrolysis species. Gallium hydrolyses to a greater extent than aluminium, with the onset of hydrolysis reactions occurring just above a pHof 1. In fact, even though aluminium has the smallest ionic radius of this series of metals, it has the weakest hydrolysis species and oxide/hydroxide phases.This is due to the presence of stabilising d-orbitals in the heavier metals, gallium, indium and thallium(III). There are few available data for the stability constants of indium(III) hydrolysis species. Of those that are available, the range in the proposed stability constants covers many orders of magnitude.

Challenges in LCA modelling of multiple loops for aluminium cans

DEFF Research Database (Denmark)

Niero, Monia; Olsen, Stig Irving

considered the case of closed-loop recycling for aluminium cans, where body and lid are different alloys, and discussed the abovementioned challenge. The Life Cycle Inventory (LCI) modelling of aluminium processes is traditionally based on a pure aluminium flow, therefore neglecting the presence of alloying...... elements. We included the effect of alloying elements on the LCA modelling of aluminium can recycling. First, we performed a mass balance of the main alloying elements (Mn, Fe, Si, Cu) in aluminium can recycling at increasing levels of recycling rate. The analysis distinguished between different aluminium...... packaging scrap sources (i.e. used beverage can and mixed aluminium packaging) to understand the limiting factors for multiple loop aluminium can recycling. Secondly, we performed a comparative LCA of aluminium can production and recycling in multiple loops considering the two aluminium packaging scrap...

Durability of bare and anodised aluminium in atmosphere of very different corrosivities I. Bare aluminium

International Nuclear Information System (INIS)

Gonzalez, J. A.; Escudero, E.; Lopez, V.; Simancas, J.; Morcillo, M.

2004-01-01

The behaviour of bare aluminium is studied in atmospheric exposure at 11 natural testing stations with salinity levels ranging between 2.1 and 684 mg Cl''- m''-2 d''-1. In atmospheres of low or moderate aggressivity aluminium behaves as a passive material, though the insignificant corrosion that is produced is sufficient to spoil its appearance. In contrast, at salinity levels of 50 mg Cl''- m''-2 ''-1 or above, aluminium is susceptible to pitting corrosion even in the first year of atmospheric exposure, or in the second year at salinities of ≤ 10 mg Cl''- m''-2 d''-1. For comparative purposes, results are included for aluminium protected with an anodic film of 28 μm thickness exposed at the same testing stations. A 28 μm anodic film, correctly sealed, prevents the risk of localised corrosion even in the most unfavourable situations. (Author) 23 refs

Spatial clustering of toxic trace elements in adolescents around the Torreón, Mexico lead–zinc smelter

Science.gov (United States)

Garcia-Vargas, Gonzalo G.; Rothenberg, Stephen J.; Silbergeld, Ellen K.; Weaver, Virginia; Zamoiski, Rachel; Resnick, Carol; Rubio-Andrade, Marisela; Parsons, Patrick J.; Steuerwald, Amy J.; Navas-Acién, Ana; Guallar, Eliseo

2016-01-01

High blood lead (BPb) levels in children and elevated soil and dust arsenic, cadmium, and lead were previously found in Torreón, northern Mexico, host to the world’s fourth largest lead–zinc metal smelter. The objectives of this study were to determine spatial distributions of adolescents with higher BPb and creatinine-corrected urine total arsenic, cadmium, molybdenum, thallium, and uranium around the smelter. Cross-sectional study of 512 male and female subjects 12–15 years of age was conducted. We measured BPb by graphite furnace atomic absorption spectrometry and urine trace elements by inductively coupled plasma-mass spectrometry, with dynamic reaction cell mode for arsenic. We constructed multiple regression models including sociodemographic variables and adjusted for subject residence spatial correlation with spatial lag or error terms. We applied local indicators of spatial association statistics to model residuals to identify hot spots of significant spatial clusters of subjects with higher trace elements. We found spatial clusters of subjects with elevated BPb (range 3.6–14.7 µg/dl) and urine cadmium (0.18–1.14 µg/g creatinine) adjacent to and downwind of the smelter and elevated urine thallium (0.28–0.93 µg/g creatinine) and uranium (0.07–0.13 µg/g creatinine) near ore transport routes, former waste, and industrial discharge sites. The conclusion derived from this study was that spatial clustering of adolescents with high BPb and urine cadmium adjacent to and downwind of the smelter and residual waste pile, areas identified over a decade ago with high lead and cadmium in soil and dust, suggests that past and/or present plant operations continue to present health risks to children in those neighborhoods. PMID:24549228

Fatigue test on aluminium bridges

NARCIS (Netherlands)

Maljaars, J.; Soetens, F.; Straalen, van IJ.J.

2005-01-01

Traffic bridges are subjected to variable loads and should therefore be checked on fatigue. Especially low weight materials, like aluminium, are sensitive to fatigue, because the variable load is a substantial part of the total load. This paper shows the structural design of an aluminium bridge

Fatal aluminium phosphide poisoning

Directory of Open Access Journals (Sweden)

Meena Mahesh Chand

2015-06-01

Full Text Available Aluminium phosphide (AlP is a cheap solid fumigant and a highly toxic pesticide which is commonly used for grain preservation. AlP has currently aroused interest with a rising number of cases in the past four decades due to increased use for agricultural and non-agricultural purposes. Its easy availability in the markets has increased also its misuse for committing suicide. Phosphine inhibits cellular oxygen utilization and can induce lipid peroxidation. Poisoning with AlP has often occurred in attempts to commit suicide, and that more often in adults than in teenagers. This is a case of suicidal consumption of aluminium phosphide by a 32-year-old young medical anesthetist. Toxicological analyses detected aluminium phosphide. We believe that free access of celphos tablets in grain markets should be prohibited by law.

Friction Welding of Aluminium and Aluminium Alloys with Steel

Directory of Open Access Journals (Sweden)

Andrzej Ambroziak

2014-01-01

Full Text Available The paper presents our actual knowledge and experience in joining dissimilar materials with the use of friction welding method. The joints of aluminium and aluminium alloys with the different types of steel were studied. The structural effects occurring during the welding process were described. The mechanical properties using, for example, (i microhardness measurements, (ii tensile tests, (iii bending tests, and (iv shearing tests were determined. In order to obtain high-quality joints the influence of different configurations of the process such as (i changing the geometry of bonding surface, (ii using the interlayer, or (iii heat treatment was analyzed. Finally, the issues related to the selection of optimal parameters of friction welding process were also investigated.

Aluminium cables in automotive applications : Prestudy of aluminium cable uses in Scania products&Failure analysis and evaluation

OpenAIRE

Man, Yu

2016-01-01

The increasing demand of light constructed vehicles as well as soaring price of copper metal owing to limited nature resources have been promoting the use of aluminium metal as an alternative conductor of automotive cables. This thesis work is to lay theoretical foundations for further research and development regarding the introduction of new automotive cables i.e. aluminium cables. Current application of automotive aluminium cables in automotive industry as well as failure analysis and eval...

Application of radioactivation analysis for determination of impurities in aluminium, raw materials and in samples from aluminium production process

International Nuclear Information System (INIS)

Vucina, L.J.

1977-01-01

Trace elements in aluminium, raw materials and in the samples from different stages of aluminium production were determined by nondestructive neutron radioactivation analysis. The samples were taken from the Bayer's process of alumina production (bauxite, red sludge and alumina), from the components of the reduction cell (anode, criolyte and AlF 3 ) and of the final product - aluminium (purity 99.5-99.7%). Under given set of conditions ten trace elements (V,La,Ga,Mn,Co,Cr,Sc,Sb,Zn and Fe) were determined in aluminium and followed through the production process. It was found that the main impurities in aluminium are iron (0.15%) and zinc (0.O6%). It has been concluded that the purity of produced aluminium depends mainly on the purity of used alumina. The second important source of contamination of aluminium is anode. The results obtained by radioactivation analysis for V, Mn, Cr and Fe fall within the ranges of concentrations of these elements determined by use of other methods (volumetry, spectrophotometry, atomic absorption). Higher values for zinc were obtained by radioactivation analysis, probably due to unsatisfactory irradiation and measuring conditions for this element. The possibilities of application of radioactivation analysis to these kinds of samples are also disscused

Aluminium in allergen-specific subcutaneous immunotherapy--a German perspective.

Science.gov (United States)

Kramer, Matthias F; Heath, Matthew D

2014-07-16

We are living in an "aluminium age" with increasing bioavailability of the metal for approximately 125 years, contributing significantly to the aluminium body burden of humans. Over the course of life, aluminium accumulates and is stored predominantly in the lungs, bones, liver, kidneys and brain. The toxicity of aluminium in humans is briefly summarised, highlighting links and possible causal relationships between a high aluminium body burden and a number of neurological disorders and disease states. Aluminium salts have been used as depot-adjuvants successfully in essential prophylactic vaccinations for almost 100 years, with a convincing positive benefit-risk assessment which remains unchanged. However, allergen-specific immunotherapy commonly consists of administering a long-course programme of subcutaneous injections using preparations of relevant allergens. Regulatory authorities currently set aluminium limits for vaccines per dose, rather than per treatment course. Unlike prophylactic vaccinations, numerous injections with higher proportions of aluminium-adjuvant per injection are applied in subcutaneous immunotherapy (SCIT) and will significantly contribute to a higher cumulative life dose of aluminium. While the human body may cope robustly with a daily aluminium overload from the environment, regulatory cumulative threshold values in immunotherapy need further addressing. Based on the current literature, predisposing an individual to an unusually high level of aluminium, such as through subcutaneous immunotherapy, has the potential to form focal accumulations in the body with the propensity to exert forms of toxicity. Particularly in relation to longer-term health effects, the safety of aluminium adjuvants in immunotherapy remains unchallenged by health authorities - evoking the need for more consideration, guidance, and transparency on what is known and not known about its safety in long-course therapy and what measures can be taken to prevent or

Detection and removal of fluorine in the waste gases of a steel smelter and measuring air quality in its surroundings

Energy Technology Data Exchange (ETDEWEB)

Graue, G; Nagel, H

1968-01-01

Plant damage in the Duisburg area was attributed to the action of fluoride supposedly originating in industrial waste gases, particularly of steel smelters. Air quality measurements were taken near a large steel smelter for a period of three years. After eliminating errors the total concentration of fluoride in the course of 3 years was established as between 2 and 6 mg/m/sup 2/ per day. Clearly, no free fluorine is emitted by steel smelters, although gaseous fluoride compounds can occur. Downstream from metallurgical furnaces, particularly where brown smoke is emitted, this fluoride is almost completely adsorbed by the dust. Ores and other raw materials in steel smelters are liable to contain fluorides, usually in the form of fluorite. Only a small proportion of this is liberated on the sintering band. However, since the sintering waste gases are acid, less fluoride is adsorbed by dust at this point and separated during dust collection. The use of desulfurization units downstream of the sintering bands could solve this problem. If, for the time being, nothing is done in this direction, it is because the fluoride contents of these gases do not play a significant role, due to the height of the stacks in use. This is supported by the results of extensive air purity measurements in the Duisburg region, in which fluoride levels between 1 and 3 ..mu..g were found per m/sup 3/ STP of air.

Spark counting technique with an aluminium oxide film

International Nuclear Information System (INIS)

Kawai, H.; Koga, T.; Morishima, H.; Niwa, T.; Nishiwaki, Y.

1980-01-01

Automatic spark counting of etch-pits on a polycarbonate film produced by nuclear fission fragments is now used for neutron monitoring in several countries. A method was developed using an aluminium oxide film instead of a polycarbonate as the neutron detector. Aluminium oxide films were prepared as follows: A cleaned aluminium plate as an anode and a nickel plate as a cathode were immersed in dilute sulfuric acid solution and electric current flowed between the electrodes at 12degC for 10-30 minutes. Electric current density was about 10 mA/cm 2 . The aluminium plate was then kept in boiling water for 10-30 minutes for sealing. The thickness of the aluminium oxide layer formed was about 1μm. The aluminium plate attached to a plate of suitable fissionable material, such as uranium or thorium, was irradiated with neutrons and set in a usual spark counter for fission track counting. One electrode was the aluminium plate and the other was an aluminized polyester sheet. Sparked pulses were counted with a usual scaler. The advantage of using spark counting with an aluminium oxide film for neutron monitoring is rapid measurement of neutron exposure, since chemical etching which is indispensable for spark counting with a polycarbonate detector film, is not needed. (H.K.)

Environmental impact of active and abandoned mines and metal smelters in Slovenia

Directory of Open Access Journals (Sweden)

Tomaž Budkovič

2003-06-01

Full Text Available Slovenia has long been known for its numerous mines and ore processing. From the times of the Roman Empire to now, 49 mines and open pits were opened, four of them were large (Idrija, Mežica – Topla, Litija and Žirovski vrh. There were also 25 oreprocessing plants and smelters, which were operating mostly in the vicinity of larger mines (Idrija, Žerjav, Celje. Due to the lack of written sources, we probably haven succeeded in making a complete list of them. There were 33 iron works operating in the vicinity ofmines and open pits, three large ones have further developed and are still operating (Jesenice, Ravne na Koroškem and Štore. As the ore processing capacities have far exceeded the capacities of the Slovenian mining, ore has long been imported and only processed in Slovenia. On the basis of the results of our investigations in the vicinity of larger mines and smelters we estimated that in Slovenia the areas in which critical limit for heavy metal content is exceeded sums up to about 80 km2.

Steam generated conversion coating on aluminium alloys

DEFF Research Database (Denmark)

Din, Rameez Ud; Jellesen, Morten Stendahl; Ambat, Rajan

Aluminium and its alloys are widely used in aerospace industry owing to their high strength to weight ratio. The surface of aluminium under normal conditions has a thin oxide film (2.5-10 nm) responsible for its inherent corrosion resistance. This oxide film can further be converted or transformed...... into functional conversion coatings in order to enhance corrosion resistance and adhesion to paint systems. Chromium based conversion coatings have been extensively used on aluminium alloys to improve adhesion of subsequent paint layers and corrosion resistance. However, the use of hexavalent chromium is strictly...... regulated due to its toxic nature and suspected carcinogenicity. So, it is highly imperative to develop other alternatives for chrome conversion coatings. Treatment of aluminium with natural water at elevated temperatures results in the formation of different forms of aluminium oxide (γ-AlO(OH) , Al(OH)3...

Advances in development and application of aluminium batteries

DEFF Research Database (Denmark)

Qingfeng, Li; Zhuxian, Qiu

2001-01-01

Aluminium has long attracted attention as a potential battery anode because of its high theoretical voltage and specific energy. The protective oxide layer at aluminium surface is however detrimental to its performance to achieve its reversible potential, and also causing the delayed activation o...... aluminium batteres, especially aluminium-air batteries, and a wide range of their applications from emergency power supplies, reserve batteries field portable batteries, to batteries for electric vehicles and underwater propulsion....

Alveolar proteinosis associated with aluminium dust inhalation.

Science.gov (United States)

Chew, R; Nigam, S; Sivakumaran, P

2016-08-01

Secondary alveolar proteinosis is a rare lung disease which may be triggered by a variety of inhaled particles. The diagnosis is made by detection of anti-granulocyte-macrophage colony-stimulating factor antibodies in bronchoalveolar lavage fluid, which appears milky white and contains lamellar bodies. Aluminium has been suggested as a possible cause, but there is little evidence in the literature to support this assertion. We report the case of a 46-year-old former boilermaker and boat builder who developed secondary alveolar proteinosis following sustained heavy aluminium exposure. The presence of aluminium was confirmed both by histological examination and metallurgical analysis of a mediastinal lymph node. Despite cessation of exposure to aluminium and treatment with whole-lung lavage which normally results in improvements in both symptoms and lung function, the outcome was poor and novel therapies are now being used for this patient. It may be that the natural history in aluminium-related alveolar proteinosis is different, with the metal playing a mediating role in the disease process. Our case further supports the link between aluminium and secondary alveolar proteinosis and highlights the need for measures to prevent excessive aluminium inhalation in relevant industries. © The Author 2016. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Metal contamination in wildlife living near two zinc smelters

Science.gov (United States)

Beyer, W.N.; Pattee, O.H.; Sileo, L.; Hoffman, D.J.; Mulhern, B.M.

1985-01-01

Wildlife in an oak forest on Blue Mountain was studied 10 km upwind (Bake Oven Knob site) and 2 km downwind (Palmerton site) of two zinc smelters in eastern Pennsylvania, USA. Previous studies at sites near these smelters had shown changes in populations of soil microflora, lichens, green plants and litter-inhabiting arthropods. The 02 soil litter horizon at Palmerton was heavily contaminated with Pb (2700 mg kg-1), Zn (24000 mg kg-1), and Cd (710 mg kg-1), and to a lesser extent with Cu (440 mg kg-1). Various kinds of invertebrates (earthworms, slugs and millipedes) that feed on soil litter or soil organic matter were rare at, or absent from, the Palmerton site. Those collected at Bake Oven Knob tended to have much higher concentrations of metals than did other invertebrates. Frogs, toads and salamanders were very rare at, or absent from, the Palmerton site, but were present at Bake Oven Knob and at other sites on Blue Mountain farther from the smelters. Metal concentrations (dry wt) in different organisms from Palmerton were compared. Concentrations of Pb were highest in shrews (110 mg kg-1), followed by songbirds (56 mg kg-1), leaves (21 mg kg-1), mice (17 mg kg-1), carrion insects (14 mg kg-1), berries (4.0 mg kg-1), moths (4,3 mg kg-1) and fungi (3.7 mg kg-1). Concentrations of Cd, in contrast, were highest in carrion insects (25 mg kg-1 ),followed by fungi (9.8 mg kg-1), leaves (8.1 mg kg-1), shrews (7.3 mg kg-I), moths (4.9 mg kg-1), mice (2.6 mg kg -1), songbirds (2.5 mg kg -1) and berries (1.2 mg kg-1). Concentrations of Zn and Cu tended to be highest in the same organisms that had the highest concentrations of Cd. Only a small proportion of the metals in the soil became incorporated into plant foliage, and much of the metal contamination detected in the biota probably came from aerial deposition. The mice from both sites seemed to be healthy. Shrews had higher concentrations of metals than did mice, and one shrew showed evidence of Pb poisoning; its red

Ion beam analysis of aluminium in thin layers

International Nuclear Information System (INIS)

Healy, M.J.F.; Pidduck, A.J.; Dollinger, G.; Gorgens, L.; Bergmaier, A.

2002-01-01

This work quantifies aluminium in thin surface and near surface layers. In one example, the layer overlies a thin gallium nitride layer on an aluminium oxide substrate and in a second example the aluminium exists just below the surface of an indium arsenide substrate. The technique of non-Rutherford elastic backscattering of protons was used for the samples where aluminum in the layer of interest needed to be resolved from aluminium in the sapphire substrate and the results were corroborated at the Technische Universitaet Muenchen using heavy ion elastic recoil detection analysis. In the second example, where it was unnecessary to isolate the signal of aluminium in the layer of interest (as the substrate contained no aluminium), then the 27 Al(d,p 01 ) 28 Al nuclear reaction was used. The elastic proton scattering cross section of aluminum was found to vary very rapidly over the energy range of interest

The aluminium content of infant formulas remains too high.

Science.gov (United States)

Chuchu, Nancy; Patel, Bhavini; Sebastian, Blaise; Exley, Christopher

2013-10-08

Recent research published in this journal highlighted the issue of the high content of aluminium in infant formulas. The expectation was that the findings would serve as a catalyst for manufacturers to address a significant problem of these, often necessary, components of infant nutrition. It is critically important that parents and other users have confidence in the safety of infant formulas and that they have reliable information to use in choosing a product with a lower content of aluminium. Herein, we have significantly extended the scope of the previous research and the aluminium content of 30 of the most widely available and often used infant formulas has been measured. Both ready-to-drink milks and milk powders were subjected to microwave digestion in the presence of 15.8 M HNO3 and 30% w/v H2O2 and the aluminium content of the digests was measured by TH GFAAS. Both ready-to-drink milks and milk powders were contaminated with aluminium. The concentration of aluminium across all milk products ranged from ca 100 to 430 μg/L. The concentration of aluminium in two soya-based milk products was 656 and 756 μg/L. The intake of aluminium from non-soya-based infant formulas varied from ca 100 to 300 μg per day. For soya-based milks it could be as high as 700 μg per day. All 30 infant formulas were contaminated with aluminium. There was no clear evidence that subsequent to the problem of aluminium being highlighted in a previous publication in this journal that contamination had been addressed and reduced. It is the opinion of the authors that regulatory and other non-voluntary methods are now required to reduce the aluminium content of infant formulas and thereby protect infants from chronic exposure to dietary aluminium.

Preparation of aluminium lakes by electrocoagulation

OpenAIRE

Prapai Pradabkham

2008-01-01

Aluminium lakes have been prepared by electrocoagulation employing aluminium as electrodes. The electrocoagulation is conducted in an aqueous alcoholic solution and is completed within one hour. The dye content in the lake ranges approximately between 4-32%.

76 FR 17548 - Prevention of Significant Deterioration (PSD) and Nonattainment New Source Review (NSR...

Science.gov (United States)

2011-03-30

...; (vi) Primary aluminum ore reduction plants; (vii) Primary copper smelters; (viii) Municipal... acid plants; (x) Petroleum refineries; (xi) Lime plants; (xii) Phosphate rock processing plants; (xiii... smelters; (e) Iron and steel mills; (f) Primary aluminum ore reduction plants; (g) Primary copper smelters...

Transformation of arsenic-rich copper smelter flue dust in contrasting soils: A 2-year field experiment

Czech Academy of Sciences Publication Activity Database

Jarošíková, A.; Ettler, V.; Mihaljevič, M.; Penížek, V.; Matoušek, Tomáš; Culka, A.; Drahota, P.

2018-01-01

Roč. 237, JUN (2018), s. 83-92 ISSN 0269-7491 Institutional support: RVO:68081715 Keywords : arsenic * smelter dust * soil Subject RIV: CB - Analytical Chemistry, Separation OBOR OECD: Analytical chemistry Impact factor: 5.099, year: 2016

Serum aluminium levels of workers in the bauxite mines.

Science.gov (United States)

de Kom, J F; Dissels, H M; van der Voet, G B; de Wolff, F A

1997-01-01

Aluminium is produced from the mineral bauxite. Occupational exposure is reported during the industrial processing of aluminium and is associated with pulmonary and neurotoxicity. However, data on exposure and toxicity of workers in the open bauxite mining industry do not exist. Therefore, a study was performed to explore aluminium exposure in employees involved in this bauxite mining process in a Surinam mine. A group of workers occupationally exposed to aluminium in an open bauxite mine were compared with a group of nonexposed wood processors. Serum aluminium was analyzed using atomic absorption spectrometry Data from the clinical chemistry of the blood and a questionnaire were used to explore determinants for aluminium exposure. No significant difference between serum aluminium in the exposed (4.4 +/- 2.0 micrograms/L, n = 27) and control group (5.1 +/- 1.5 micrograms/L, n = 27) was detected. For the serum concentration of the clinical chemical variables (calcium, citrate, and creatinine), a statistically significant difference was computed (p < or = 0.02) between the exposed and control group. All levels were slightly higher in the exposed group; no statistically significant correlations with serum aluminium were found. In this study, serum aluminium values were in the normal range, no significant difference between the groups could be detected despite long-term occupational exposure.

Argon-arc welding of heat resisting aluminium alloys

International Nuclear Information System (INIS)

Ryazantsev, V.I.; Fedoseev, V.A.

1997-01-01

Welding of aluminium heat resisting alloys of the Al-Cu-Mg system is studied. The hot-shortness of heat-resistant alloys M40, 1150 and 1151 are at the level of aluminium alloys 1201 and by 2-3 times lower as compared to the aluminium alloy AMg6. The M40, 1150 and 1151 alloys have unquestionable advantages against other know aluminium alloys only at temperatures of welded structures operation, beginning with 150-2000 deg C and especially at 250 deg C

Net shape powder processing of aluminium

International Nuclear Information System (INIS)

Schaffer, G.B.

2000-01-01

The increasing interest in light weight materials coupled to the need for cost-effective processing have combined to create a significant opportunity for aluminium powder metallurgy. Net shape processing of aluminium using the classical press-and-sinter powder metallurgy technique is a unique and important metal-forming method which is cost effective in producing complex parts at, or very close to, final dimensions. This paper provides an overview of the net shape powder processing of aluminium. Current research is critically reviewed and the future potential is briefly considered

Preparation of aluminium lakes by electrocoagulation

Directory of Open Access Journals (Sweden)

Prapai Pradabkham

2008-07-01

Full Text Available Aluminium lakes have been prepared by electrocoagulation employing aluminium as electrodes. The electrocoagulation is conducted in an aqueous alcoholic solution and is completed within one hour. The dye content in the lake ranges approximately between 4-32%.

Investigation of aluminium state in some popular food, which are cooked in aluminium vessels, using spectroscopic analysis methods

International Nuclear Information System (INIS)

Al-Shahneh, M.; Saheune, Kh.

2009-01-01

Aluminium and lead elements were determined in drinking water and salt solution from chick-pea and faba-bean cooked in aluminium vessels and others from teflon for comparison using atomic absorption spectroscopy by graphite furnace. The relationship between heating time and aluminium quantities transferred to these food solutions was investigated. The lead element was determined taking into consideration the fact that this element may enter in these vessels somehow during the manufacturing process. Results show that the highest value of aluminium quantities was recorded in salt solution ( 17.022 μg/ml) without heating , followed by chick-pea solution (9.95 μg/ml), then faba-bean solution (2.81 μg/ml) when the heated period was 120 minutes. (author)

Effect of tempering on corrosion resistance of cast aluminium bronzes

International Nuclear Information System (INIS)

Aaltonen, P.; Klemetti, K.; Haenninen, H.

1985-01-01

The subject of this study is corrosion resistance of aluminium bronzes, which are copper base alloys containing aluminium up to 12% with additions of nickel, iron and manganese. The main conclutions that can be drawn are: (1) The dealloying corrosion resistance of nickel-aluminium bronze is much better than that of aluminium bronze with iron and manganese additions, but it is not immune; (2) The dealloying corrosion resistance of aluminium bronzes can be improved by appropiate heat treatments. The best properties were obtained by temperering between 600 and 800 deg C, depending on the initial microstructure; (3) In crevice conditions, where local acidification can occur, dealloying of aluminium bronzes is a consequence of the preferential attack of aluminium-rich phases. By appropriate tempering, a uniform distribution of aluminium-rich phases is obtained and the continous path for selective corrosion is not formed

What is the risk of aluminium as a neurotoxin?

Science.gov (United States)

Exley, Christopher

2014-06-01

Aluminium is neurotoxic. Its free ion, Al(3+) (aq), is highly biologically reactive and uniquely equipped to do damage to essential cellular (neuronal) biochemistry. This unequivocal fact must be the starting point in examining the risk posed by aluminium as a neurotoxin in humans. Aluminium is present in the human brain and it accumulates with age. The most recent research demonstrates that a significant proportion of individuals older than 70 years of age have a potentially pathological accumulation of aluminium somewhere in their brain. What are the symptoms of chronic aluminium intoxication in humans? What if neurodegenerative diseases such as Alzheimer's disease are the manifestation of the risk of aluminium as a neurotoxin? How might such an (outrageous) hypothesis be tested?

Assessment of Fluoride Concentration of Soil and Vegetables in Vicinity of Zinc Smelter, Debari, Udaipur, Rajasthan.

Science.gov (United States)

Bhat, Nagesh; Jain, Sandeep; Asawa, Kailash; Tak, Mridula; Shinde, Kushal; Singh, Anukriti; Gandhi, Neha; Gupta, Vivek Vardhan

2015-10-01

As of late, natural contamination has stimulated as a reaction of mechanical and other human exercises. In India, with the expanding industrialization, numerous unsafe substances are utilized or are discharged amid generation as cleans, exhaust, vapours and gasses. These substances at last are blended in the earth and causes health hazards. To determine concentration of fluoride in soils and vegetables grown in the vicinity of Zinc Smelter, Debari, Udaipur, Rajasthan. Samples of vegetables and soil were collected from areas situated at 0, 1, 2, 5, and 10 km distance from the zinc smelter, Debari. Three samples of vegetables (i.e. Cabbage, Onion and Tomato) and 3 samples of soil {one sample from the upper layer of soil (i.e. 0 to 20 cm) and one from the deep layer (i.e. 20 - 40 cm)} at each distance were collected. The soil and vegetable samples were sealed in clean polythene bags and transported to the laboratory for analysis. One sample each of water and fertilizer from each distance were also collected. The mean fluoride concentration in the vegetables grown varied between 0.36 ± 0.69 to 0.71 ± 0.90 ppm. The fluoride concentration in fertilizer and water sample from various distances was found to be in the range of 1.4 - 1.5 ppm and 1.8 - 1.9 ppm respectively. The fluoride content of soil and vegetables was found to be higher in places near to the zinc smelter.

Novel manufacturing method by using stainless steel pipes expanded into aluminium profiles for the ITER Neutral Beam cryopumps

Energy Technology Data Exchange (ETDEWEB)

Dremel, Matthias, E-mail: matthias.dremel@iter.org; Boissin, Jean-Claude; Déléage, Vincent; Quinn, Eamonn; Pearce, Robert

2015-10-15

This paper describes the novel engineering and manufacturing solution of stainless steel pipe expansion into aluminium extrusion profiles for use at cryogenic temperatures up to 400 K. This fabrication method will be used for the thermal radiation shields and the cryopanels of the ITER Neutral Beam cryopumps. The use of stainless steel pipes expanded into aluminium extrusion profiles is a solution that combines standard stainless steel welding procedures for the manifolds of the cooling circuits with extended aluminium structures taking advantage of the high thermal conductivity of aluminium. The cryogenic cooling circuits of the pump are a first confinement barrier in the ITER vacuum vessel and the risk of a leakage needs to be minimized as far as possible. The expansion method avoids the need of joints of dissimilar materials in the primary confinement barrier. The fabrication method and results of the prototyping of full scaled components for the ITER Neutral Beam cryopumps are outlined in this paper.

Analysis of metal(loid)s contamination and their continuous input in soils around a zinc smelter: Development of methodology and a case study in South Korea.

Science.gov (United States)

Yun, Sung-Wook; Baveye, Philippe C; Kim, Dong-Hyeon; Kang, Dong-Hyeon; Lee, Si-Young; Kong, Min-Jae; Park, Chan-Gi; Kim, Hae-Do; Son, Jinkwan; Yu, Chan

2018-07-01

Soil contamination due to atmospheric deposition of metals originating from smelters is a global environmental problem. A common problem associated with this contamination is the discrimination between anthropic and natural contributions to soil metal concentrations: In this context, we investigated the characteristics of soil contamination in the surrounding area of a world class smelter. We attempted to combine several approaches in order to identify sources of metals in soils and to examine contamination characteristics, such as pollution level, range, and spatial distribution. Soil samples were collected at 100 sites during a field survey and total concentrations of As, Cd, Cr, Cu, Fe, Hg, Ni, Pb, and Zn were analyzed. We conducted a multivariate statistical analysis, and also examined the spatial distribution by 1) identifying the horizontal variation of metals according to particular wind directions and distance from the smelter and 2) drawing a distribution map by means of a GIS tool. As, Cd, Cu, Hg, Pb, and Zn in the soil were found to originate from smelter emissions, and As also originated from other sources such as abandoned mines and waste landfill. Among anthropogenic metals, the horizontal distribution of Cd, Hg, Pb, and Zn according to the downwind direction and distance from the smelter showed a typical feature of atmospheric deposition (regression model: y = y 0  + αe -βx ). Lithogenic Fe was used as an indicator, and it revealed the continuous input and accumulation of these four elements in the surrounding soils. Our approach was effective in clearly identifying the sources of metals and analyzing their contamination characteristics. We believe this study will provide useful information to future studies on soil pollution by metals around smelters. Copyright © 2018 Elsevier Ltd. All rights reserved.

Detection of aluminium in different culinary media using black ...

African Journals Online (AJOL)

Jacques Blessing

The interactions between food and aluminium local kitchen utensils can be a potential source of aluminium released which can ... need to be adopted to preserve consumers' health. ..... Corrosion behaviour of different ... Aluminium beverage.

There is (still too much aluminium in infant formulas

Directory of Open Access Journals (Sweden)

Burrell Shelle-Ann M

2010-08-01

Full Text Available Abstract Background Infant formulas are sophisticated milk-based feeds for infants which are used as a substitute for breast milk. Historically they are known to be contaminated by aluminium and in the past this has raised health concerns for exposed infants. We have measured the aluminium content of a number of widely used infant formulas to determine if their contamination by aluminium and consequent issues of child health persists. Methods Samples of ready-made milks and powders used to make milks were prepared by microwave digestion of acid/peroxide mixtures and their aluminium content determined by THGA. Results The concentration of aluminium in ready-made milks varied from ca 176 to 700 μg/L. The latter concentration was for a milk for preterm infants. The aluminium content of powders used to make milks varied from ca 2.4 to 4.3 μg/g. The latter content was for a soya-based formula and equated to a ready-to-drink milk concentration of 629 μg/L. Using the manufacturer's own guidelines of formula consumption the average daily ingestion of aluminium from infant formulas for a child of 6 months varied from ca 200 to 600 μg of aluminium. Generally ingestion was higher from powdered as compared to ready-made formulas. Conclusions The aluminium content of a range of well known brands of infant formulas remains high and particularly so for a product designed for preterm infants and a soya-based product designed for infants with cow's milk intolerances and allergies. Recent research demonstrating the vulnerability of infants to early exposure to aluminium serves to highlight an urgent need to reduce the aluminium content of infant formulas to as low a level as is practically possible.

Molybdenum solubility in aluminium nitrate solutions

Energy Technology Data Exchange (ETDEWEB)

Heres, X.; Sans, D.; Bertrand, M.; Eysseric, C. [CEA, Centre de Marcoule, Nuclear Energy Division, DRCP, BP 17171, 30207 Bagnols-sur-Ceze Cedex (France); Brackx, E.; Domenger, R.; Excoffier, E. [CEA, Centre de Marcoule, Nuclear Energy Division, DTEC, BP 17171, 30207 Bagnols-sur-Ceze Cedex (France); Valery, J.F. [AREVA-NC, DOR/RDP, Paris - La Defense (France)

2016-07-01

For over 60 years, research reactors (RR or RTR for research testing reactors) have been used as neutron sources for research, radioisotope production ({sup 99}Mo/{sup 99m}Tc), nuclear medicine, materials characterization, etc... Currently, over 240 of these reactors are in operation in 56 countries. They are simpler than power reactors and operate at lower temperature (cooled to below 100 C. degrees). The fuel assemblies are typically plates or cylinders of uranium alloy and aluminium (U-Al) coated with pure aluminium. These fuels can be processed in AREVA La Hague plant after batch dissolution in concentrated nitric acid and mixing with UOX fuel streams. The aim of this study is to accurately measure the solubility of molybdenum in nitric acid solution containing high concentrations of aluminium. The higher the molybdenum solubility is, the more flexible reprocessing operations are, especially when the spent fuels contain high amounts of molybdenum. To be most representative of the dissolution process, uranium-molybdenum alloy and molybdenum metal powder were dissolved in solutions of aluminium nitrate at the nominal dissolution temperature. The experiments showed complete dissolution of metallic elements after 30 minutes long stirring, even if molybdenum metal was added in excess. After an induction period, a slow precipitation of molybdic acid occurs for about 15 hours. The data obtained show the molybdenum solubility decreases with increasing aluminium concentration. The solubility law follows an exponential relation around 40 g/L of aluminium with a high determination coefficient. Molybdenum solubility is not impacted by the presence of gadolinium, or by an increasing concentration of uranium. (authors)

Niobium-base grain refiner for aluminium

International Nuclear Information System (INIS)

Silva Pontes, P. da; Robert, M.H.; Cupini, N.L.

1980-01-01

A new chemical grain refiner for aluminium has been developed, using inoculation of a niobium-base compound. When a bath of molten aluminium is inoculated whith this refiner, an intermetallic aluminium-niobium compound is formed which acts as a powerful nucleant, producing extremely fine structure comparable to those obtained by means of the traditional grain refiner based on titanium and boron. It was found that the refinement of the structure depends upon the weight percentage of the new refiner inoculated as well as the time of holding the bath after inoculation and before pouring, but mainly on the inoculating temperature. (Author) [pt

The heavy metal partition in size-fractions of the fine particles in agricultural soils contaminated by waste water and smelter dust

Energy Technology Data Exchange (ETDEWEB)

Zhang, Haibo, E-mail: hbzhang@yic.ac.cn [Yantai Institute of Coastal Zone Research, Chinese Academy of Sciences, Yantai 264003 (China); Luo, Yongming, E-mail: ymluo@yic.ac.cn [Yantai Institute of Coastal Zone Research, Chinese Academy of Sciences, Yantai 264003 (China); Key Laboratory of Soil Environment and Pollution Remediation, Institute of Soil Science, Chinese Academy of Sciences, Nanjing 210008 (China); Makino, Tomoyuki [National Institute for Agro-Environmental Sciences, Tsukuba 3058604 (Japan); Wu, Longhua [Key Laboratory of Soil Environment and Pollution Remediation, Institute of Soil Science, Chinese Academy of Sciences, Nanjing 210008 (China); Nanzyo, Masami [Tohoku University, Sendai 9808576 (Japan)

2013-03-15

Highlights: ► A continuous flow ultra-centrifugation method has been developed to obtain fine particles from polluted agricultural soil. ► Pollution source affected the heavy metal fractionation in size-fractions by changing soil particle properties. ► The iron oxides affected the distribution of lead species more than other metals in the smelter dust polluted particles. -- Abstract: The partitioning of pollutant in the size-fractions of fine particles is particularly important to its migration and bioavailability in soil environment. However, the impact of pollution sources on the partitioning was seldom addressed in the previous studies. In this study, the method of continuous flow ultra-centrifugation was developed to separate three size fractions (<1 μm, <0.6 μm and <0.2 μm) of the submicron particles from the soil polluted by wastewater and smelter dust respectively. The mineralogy and physicochemical properties of each size-fraction were characterized by X-ray diffraction, transmission electron microscope etc. Total content of the polluted metals and their chemical speciation were measured. A higher enrichment factor of the metals in the fractions of <1 μm or less were observed in the soil contaminated by wastewater than by smelter dust. The organic substance in the wastewater and calcite from lime application were assumed to play an important role in the metal accumulation in the fine particles of the wastewater polluted soil. While the metal accumulation in the fine particles of the smelter dust polluted soil is mainly associated with Mn oxides. Cadmium speciation in both soils is dominated by dilute acid soluble form and lead speciation in the smelter dust polluted soil is dominated by reducible form in all particles. This implied that the polluted soils might be a high risk to human health and ecosystem due to the high bioaccessblity of the metals as well as the mobility of the fine particles in soil.

The heavy metal partition in size-fractions of the fine particles in agricultural soils contaminated by waste water and smelter dust

International Nuclear Information System (INIS)

Zhang, Haibo; Luo, Yongming; Makino, Tomoyuki; Wu, Longhua; Nanzyo, Masami

2013-01-01

Highlights: ► A continuous flow ultra-centrifugation method has been developed to obtain fine particles from polluted agricultural soil. ► Pollution source affected the heavy metal fractionation in size-fractions by changing soil particle properties. ► The iron oxides affected the distribution of lead species more than other metals in the smelter dust polluted particles. -- Abstract: The partitioning of pollutant in the size-fractions of fine particles is particularly important to its migration and bioavailability in soil environment. However, the impact of pollution sources on the partitioning was seldom addressed in the previous studies. In this study, the method of continuous flow ultra-centrifugation was developed to separate three size fractions (<1 μm, <0.6 μm and <0.2 μm) of the submicron particles from the soil polluted by wastewater and smelter dust respectively. The mineralogy and physicochemical properties of each size-fraction were characterized by X-ray diffraction, transmission electron microscope etc. Total content of the polluted metals and their chemical speciation were measured. A higher enrichment factor of the metals in the fractions of <1 μm or less were observed in the soil contaminated by wastewater than by smelter dust. The organic substance in the wastewater and calcite from lime application were assumed to play an important role in the metal accumulation in the fine particles of the wastewater polluted soil. While the metal accumulation in the fine particles of the smelter dust polluted soil is mainly associated with Mn oxides. Cadmium speciation in both soils is dominated by dilute acid soluble form and lead speciation in the smelter dust polluted soil is dominated by reducible form in all particles. This implied that the polluted soils might be a high risk to human health and ecosystem due to the high bioaccessblity of the metals as well as the mobility of the fine particles in soil

IEC 61267: Feasibility of type 1100 aluminium and a copper/aluminium combination for RQA beam qualities.

Science.gov (United States)

Leong, David L; Rainford, Louise; Zhao, Wei; Brennan, Patrick C

2016-01-01

In the course of performance acceptance testing, benchmarking or quality control of X-ray imaging systems, it is sometimes necessary to harden the X-ray beam spectrum. IEC 61267 specifies materials and methods to accomplish beam hardening and, unfortunately, requires the use of 99.9% pure aluminium (Alloy 1190) for the RQA beam quality, which is expensive and difficult to obtain. Less expensive and more readily available filters, such as Alloy 1100 (99.0% pure) aluminium and copper/aluminium combinations, have been used clinically to produce RQA series without rigorous scientific investigation to support their use. In this paper, simulation and experimental methods are developed to determine the differences in beam quality using Alloy 1190 and Alloy 1100. Additional simulation investigated copper/aluminium combinations to produce RQA5 and outputs from this simulation are verified with laboratory tests using different filter samples. The results of the study demonstrate that although Alloy 1100 produces a harder beam spectrum compared to Alloy 1190, it is a reasonable substitute. A combination filter of 0.5 mm copper and 2 mm aluminium produced a spectrum closer to that of Alloy 1190 than Alloy 1100 with the added benefits of lower exposures and lower batch variability. Copyright © 2015 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

Remediation of phosphate-contaminated water by electrocoagulation with aluminium, aluminium alloy and mild steel anodes.

Science.gov (United States)

Vasudevan, Subramanyan; Lakshmi, Jothinathan; Jayaraj, Jeganathan; Sozhan, Ganapathy

2009-05-30

The present study provides an electrocoagulation process for the remediation of phosphate-contaminated water using aluminium, aluminium alloy and mild steel as the anodes and stainless steel as the cathode. The various parameters like effect of anode materials, effect of pH, concentration of phosphate, current density, temperature and co-existing ions, and so forth, and the adsorption capacity was evaluated using both Freundlich and Langmuir isotherm models. The adsorption of phosphate preferably fitting the Langmuir adsorption isotherm suggests monolayer coverage of adsorbed molecules. The results showed that the maximum removal efficiency of 99% was achieved with aluminium alloy anode at a current density of 0.2 A dm(-2), at a pH of 7.0. The adsorption process follows second-order kinetics.

Lead isotopes in soils near five historic American lead smelters and refineries

International Nuclear Information System (INIS)

Rabinowitz, Michael B.

2005-01-01

This survey of soil lead in the vicinity of old industrial sites examines how the stable isotope patterns vary among the sites according to the sources of the lead ore processed at each site. Lead smelters and refineries, which closed down decades ago, are the basis of this investigation. Samples were taken from near five old factory sites in Collinsville and Alton (Illinois), Ponderay (Idaho), East Chicago (Indiana) and Omaha (Nebraska). Historical records were searched for accounts of the sources of the lead. Lead concentrations were measured by atomic absorption flame spectrophotometry, and stable isotopic analysis was done by plasma ionization mass spectrometry. At every site visited, remnants of the old factories, in terms of soil lead pollution, could be found. In spite of potential complications of varying smelter feedstock sourced from mines of different geological age, it was possible to match the isotopic patterns in the soils with the documented sources of the ores. The Collinsville and Alton sites resembled Missouri lead. The Ponderay value was higher than major Bunker Hill, Idaho deposits, but closer to the minor, nearby Oreille County, Washington ores. Mostly Utah ore was used in East Chicago. The Omaha soil reflects lead from Mexico, Colorado and Montana

Method for aluminium dross utilization

International Nuclear Information System (INIS)

Lucheva, B.; Petkov, R.; Tzonev, Tz.

2003-01-01

A new hydrometallurgical method has been developed for metal aluminum utilization from secondary aluminum dross. Secondary aluminum dross is a powder product with an average of 35% aluminium content (below 1mm). It is waste from primary aluminum dross pyrometallurgical flux less treatment in rotary DC electric arc furnace. This method is based on aluminum leaching in copper chloride water solution. As a result an aluminum oxychloride solution and solids, consisting of copper and oxides are obtained. In order to copper chloride solution regenerate hydrochloric acid is added to the solids. The process is simple, quick, economic and safe. The aluminum oxychloride solution contains 56 g/l Al 2 O 3 . The molar ratios are Al:Cl=0,5; OH:Al=1. The solution has 32 % basicity and 1,1 g/cm 3 density. For increasing the molar ratio of aluminium to chlorine aluminum hydroxide is added to this solution at 80 o C. Aluminum hydroxide is the final product from the secondary aluminum dross alkaline leaching. As a result aluminum oxychloride solution of the following composition is prepared: Al 2 O 3 - 180 g/l; Al:Cl=1,88; OH:Al=4,64; basicity 82%; density 1,22 g/cm 3 , pH=4 -4,5. Aluminum oxychloride solution produced by means of this method can be used in potable and wastewater treatment, paper making, in refractory mixture as a binder etc. (Original)

Human biomonitoring of aluminium after a single, controlled manual metal arc inert gas welding process of an aluminium-containing worksheet in nonwelders.

Science.gov (United States)

Bertram, Jens; Brand, Peter; Hartmann, Laura; Schettgen, Thomas; Kossack, Veronika; Lenz, Klaus; Purrio, Ellwyn; Reisgen, Uwe; Kraus, Thomas

2015-10-01

Several existing field studies evaluate aluminium welding works but no thoroughly controlled exposure scenario for welding fume has been described yet. This study provides information about the uptake and elimination of aluminium from welding fumes under controlled conditions. In the Aachen Workplace Simulation Laboratory, we are able to generate welding fumes of a defined particle mass concentration. We exposed 12, until then occupationally unexposed participants with aluminium-containing welding fumes of a metal inert gas (MIG) welding process of a total dust mass concentration of 2.5 mg/m(3) for 6 h. Room air filter samples were collected, and the aluminium concentration in air derived. Urine and plasma samples were collected directly before and after the 6-h lasting exposure, as well as after 1 and 7 days. Human biomonitoring methods were used to determine the aluminium content of the samples with high-resolution continuum source atomic absorption spectrometry. Urinary aluminium concentrations showed significant changes after exposure compared to preexposure levels (mean t(1) (0 h) 13.5 µg/L; mean t(2) (6 h) 23.5 µg/L). Plasma results showed the same pattern but pre-post comparison did not reach significance. We were able to detect a significant increase of the internal aluminium burden of a single MIG aluminium welding process in urine, while plasma failed significance. Biphasic elimination kinetic can be observed. The German BAT of 60 µg/g creatinine was not exceeded, and urinary aluminium returned nearly to baseline concentrations after 7 days.

Multiply-negatively charged aluminium clusters and fullerenes

Energy Technology Data Exchange (ETDEWEB)

Walsh, Noelle

2008-07-15

Multiply negatively charged aluminium clusters and fullerenes were generated in a Penning trap using the 'electron-bath' technique. Aluminium monoanions were generated using a laser vaporisation source. After this, two-, three- and four-times negatively charged aluminium clusters were generated for the first time. This research marks the first observation of tetra-anionic metal clusters in the gas phase. Additionally, doubly-negatively charged fullerenes were generated. The smallest fullerene dianion observed contained 70 atoms. (orig.)

Irradiation of aluminium alloy materials with electron beam

International Nuclear Information System (INIS)

Konno, Osamu; Masumoto, Kazuyoshi

1982-01-01

It is a theme with a room for discussion to employ the stainless steel composed of longer half-life materials for the vacuum system of accelerators, from the viewpoint of radiation exposure. Therefore, it is desirable to use aluminium of shorter half-life in place of stainless steel. As a result of investigation on the above theme in the 1.2 GeV electron linac project in Tohoku University, it has been concluded that aluminium alloy vacuum chambers can reduce exposure dose by about one or two figures as compared with stainless steel ones. Of course, aluminium alloy contains trace amounts of Mg, Si, Ti, Cr, Mn, Fe, Zn, Cu and others. Therefore, four kinds of aluminium alloy considered to be usable have been examined for induced radioactivity by electron beam irradiation. Stainless steel SUS 304 has been also irradiated for comparison. Radiation energy has been 30 MeV and 200 MeV. When stainless steel and aluminium alloy were compared, aluminium alloy was very effective for reducing surface dose in low energy irradiation. In 200 MeV irradiation, the dose ratio of aluminium alloy to stainless steel became 1/30 to 1/100 after one week, though the dose difference between these two materials became smaller in 100 days or more after irradiation. If practical inspection and repair are implemented during the period from a few days to one week after shutdown, the aluminium alloy is preferable for exposure dose reduction even in high energy irradiation. (Wakatsuki, Y.)

Introduction. Aluminium production on electrolytic cells with calcined anodes

International Nuclear Information System (INIS)

Galushkin, N.V.

1995-01-01

This chapter presents the monograph content, which includes the description of physicochemical processes in aluminium electrolytic cells, and mechanism of electrolytic aluminium obtaining. The short description of aluminium electrolytic cells construction is presented in this book as well.

Aluminium allergy and granulomas induced by vaccinations for children

DEFF Research Database (Denmark)

Andersen, Rosa Marie O; Zachariae, Claus; Johansen, Jeanne Duus

2014-01-01

Vaccination with aluminium-adsorbed vaccines can induce aluminium allergy with persistent itching subcutaneous nodules at the injection site - vaccination granulomas. In this article we give an overview of childhood aluminium-adsorbed vaccines available in Denmark. Through literature studies we...

Synthesis and properties of bimetallic aluminium alkoxides

International Nuclear Information System (INIS)

Vyshinskaya, K.I.; Vasil'ev, G.A.; Vishnyakova, T.A.

1997-01-01

A single stage method of aluminium bimetallic alkoxide synthesis, which consists in activated aluminium reaction with metal salts in the relevant alcohols, has been developed. Properties of the compounds prepared are described

Beryllium electrodeposition on aluminium cathode from chloride melts

International Nuclear Information System (INIS)

Nichkov, I.F.; Novikov, E.A.; Serebryakov, G.A.; Kanashin, Yu.P.; Sardyko, G.N.

1980-01-01

Cathodic processes during beryllium deposition on liquid and solid aluminium cathodes are investigated. Mixture of sodium, potassium and beryllium chloride melts served as an lectrolyte. Beryllium ion discharge at the expense of alloy formation takes place at more positive potentials than on an indifferent cathode at low current densities ( in the case of liquid aluminium cathode). Metallographic analysis and measurements of microhardness have shown, that the cathodic product includes two phases: beryllium solid solution in aluminium and metallic beryllium. It is concluded, that aluminium-beryllium alloys with high cathodic yield by current can be obtained by the electrolytic method

Investigation process of alcoholysis of hydride aluminium-adobe

International Nuclear Information System (INIS)

Numanov, M.I.; Normatov, I.Sh.; Mirsaidov, U.M.

2001-01-01

Considering of that process of acid treatment of aluminium-adobe hydride realizes in the ethyl alcohol media it was necessary study the process of alcoholysis of AlH 3 and aluminium additives. In the end of article authors became to conclusion that deficiency of spontaneous alcoholysis of AlH 3 in adobe caused by protective action of fiber; solvate ability of LiCl and alkoxy aluminium hydride of lithium-LiCl·CO 2 H 5 OH, Li Al(OC 2 H 5 ) 4 ·nC 2 H 5 OH decreasing the expectancy of responding of alcohol with aluminium hydride

KS R41B. A high performance steel-aluminium composite material; KS R41B. Ein Stahl-Aluminium-Verbundwerkstoff fuer hohe Belastungen

Energy Technology Data Exchange (ETDEWEB)

Deicke, K. [KS Gleitlager GmbH (Germany). Bereich Metall; Matucha, H.; Schubert, W. [KS Gleitlager GmbH, St. Leon-Rot (Germany); Steffens, T. [KS Gleitlager GmbH, Neckarsulm (Germany)

2002-08-01

Aluminium-tin alloys have been well-known for a long time and have proved to be suitable bearing materials for crankshaft bearings for many years. The known alloy AlZn4,5SiCuPb is one of the aluminium materials capable of sustaining the highest mechanical loads. In order to achieve optimum sliding properties, it would be necessary to increase the share of the soft lead phase in the alloy. This article by KS Gleitlager GmbH shows a reasonably priced manufacturing technology for high-performance aluminium-zinc-silicon-copper alloys. (orig.) [German] Die Aluminium-Zinn-Lagerlegierungen sind seit langem bekannt und haben sich seit Jahren als Lagerwerkstoff fuer Kurbelwellenlager bewaehrt. Die Legierung AlZn4,5SiCuPb gehoert zu den mechanisch am hoechsten belastbaren Aluminium-Werkstoffen. Um optimale Gleiteigenschaften zu erzielen, muesste in der Legierung der Anteil des weichen Bleis noch weiter erhoeht werden. Dieser Beitrag der KS Gleitlager GmbH zeigt eine kostenguenstige Herstelltechnologie fuer hochbelastbare Aluminium-Zink-Silizium-Kupfer-Legierungen. (orig.)

Energy Absorption of Monolithic and Fibre Reinforced Aluminium Cylinders

NARCIS (Netherlands)

De Kanter, J.L.C.G.

2006-01-01

Summary accompanying the thesis: Energy Absorption of Monolithic and Fibre Reinforced Aluminium Cylinders by Jens de Kanter This thesis presents the investigation of the crush behaviour of both monolithic aluminium cylinders and externally fibre reinforced aluminium cylinders. The research is based

Corrosion of aluminium in copper-aluminium couples under a marine environment: Influence of polyaniline deposited onto copper

International Nuclear Information System (INIS)

Vera, Rosa; Verdugo, Patricia; Orellana, Marco; Munoz, Eduardo

2010-01-01

Research highlights: → The presence of Polyaniline in the Al-Cu system produces a decrease in the oxygen reduction reaction. → In the marine enviroment, aluminium in Al-Cu couples, suffers pitting and exfoliation. → The aluminium deterioration increases with chloride and enviromental sulphur dioxide presence, mainly when it is united to bare copper. - Abstract: In this study, we examined how aluminium corrosion in Al-Cu/PANI galvanic couples in a marine environment is influenced by deposition of polyaniline (PANI) on copper. Polarization curves and immersion assays in 0.1 M NaCl were performed. The morphologies of etched Al and corrosion products were observed by SEM, and the Al ions in solution were quantified by atomic absorption spectroscopy. A reduction in aluminium damage due to galvanic corrosion was observed as a result of decreased effective area for the oxygen reduction reaction on Cu/PANI electrode. Furthermore, an electrochemical reduction of PANI from leucoemeraldine to emeraldine base is proposed.

Aluminium hydroxide-the carrier for catalysts coating

International Nuclear Information System (INIS)

Normatov, I.Sh.; Mirsaidov, U.M.

2003-01-01

At present time several methods of receiving aluminium hydroxide are exist. But all they differ by much staging of process connected with preliminary receiving of intermediate compounds, with application of expensive metallic aluminium

Effects of aluminium surface morphology and chemical modification on wettability

DEFF Research Database (Denmark)

Rahimi, Maral; Fojan, Peter; Gurevich, Leonid

2014-01-01

-life aluminium surfaces of different morphology: unpolished aluminium, polished aluminium, and aluminium foil, were subjected to surface modification procedures which involved the formation of a layer of hydrophilic hyperbranched polyethyleneglycol via in situ polymerization, molecular vapour deposition...... of a monolayer of fluorinated silane, and a combination of those. The effect of these surface modification techniques on roughness and wettability of the aluminium surfaces was elucidated by ellipsometry, contact angle measurements and atomic force microscopy. We demonstrated that by employing different types...

Solidification microstructures of aluminium-uranium alloys

International Nuclear Information System (INIS)

Ambrozio Filho, F.; Vieira, R.R.

1976-01-01

The solidification of microstrutures of aluminium-uranium alloys in the range of 4 to 20% uranium is investigated. The solidification was obtained both in ingot molds and under controlled directional solidification. The conditions for the presence of primary crystals and eutectic are discussed and an analysis of the influence of variables (growth rate and thermal gradient in the liquid) on the alloy structure is made. The effect of cooling rate on the alloy structures has been determined. It is found that the resulting structure can be derived from the kinectics concept, as required by the coupled-zone theory. Suggestions on the qualitative intervals of composition and temperatures with eutectic growth are presented [pt

76 FR 38024 - Standards of Performance for New Stationary Sources

Science.gov (United States)

2011-06-29

... January 20, 1983. O Sewage Treatment Plants X X P Primary Copper Smelters X X Q Primary Zinc Smelters X X R Primary Lead Smelters X X S Primary Aluminum Reduction Plants X X T Phosphate Fertilizer Industry: X X Wet Process Phosphoric Acid Plants. U Phosphate Fertilizer Industry: X X Superphosphoric Acid...

Aluminium removal from water after defluoridation with the electrocoagulation process.

Science.gov (United States)

Sinha, Richa; Mathur, Sanjay; Brighu, Urmila

2015-01-01

Fluoride is the most electronegative element and has a strong affinity for aluminium. Owing to this fact, most of the techniques used for fluoride removal utilized aluminium compounds, which results in high concentrations of aluminium in treated water. In the present paper, a new approach is presented to meet the WHO guideline for residual aluminium concentration as 0.2 mg/L. In the present work, the electrocoagulation (EC) process was used for fluoride removal. It was found that aluminium content in water increases with an increase in the energy input. Therefore, experiments were optimized for a minimum energy input to achieve the target value (0.7 mg/L) of fluoride in resultant water. These optimized sets were used for further investigations of aluminium control. The experimental investigations revealed that use of bentonite clay as coagulant in clariflocculation brings down the aluminium concentration of water below the WHO guideline. Bentonite dose of 2 g/L was found to be the best for efficient removal of aluminium.

Irradiation effects in magnesium and aluminium alloys

International Nuclear Information System (INIS)

Sturcken, E.F.

1979-01-01

Effects of neutron irradiation on microstructure, mechanical properties and swelling of several magnesium and aluminium alloys were studied. The neutron fluences of 2-3 X 10 22 n/cm 2 , >0.2 MeV produced displacement doses of 20 to 45 displacements per atom (dpa). Ductility of the magnesium alloys was severely reduced by irradiation induced recrystallization and precipitation of various forms. Precipitation of transmuted silicon occurred in the aluminium alloys. However, the effect on ductility was much less than for the magnesium alloys. The magnesium and aluminium alloys had excellent resistance to swelling: The best magnesium alloy was Mg/3.0 wt% Al/0.19 wt% Ca; its density decreased by only 0.13%. The best aluminium alloy was 6063, with a density decrease of 0.22%. (Auth.)

Steam Initiated Surface Modification of Aluminium Alloys

DEFF Research Database (Denmark)

Din, Rameez Ud

The extensive demand of aluminium alloys in various industries such as in transportationis mainly due to the high strength to weight ratio, which could be translated into fuel economy and efficiency. Corrosion protection of aluminium alloys is an important aspect for all applications which includes...... the use of aluminium alloys in the painted form requiring a conversion coating to improve the adhesion. Chromate based conversion coating processes are extremely good for these purposes, however the carcinogenic and toxic nature of hexavalent chromium led to the search for more benign and eco......, crystalline nano-particles, role of steam-based treatment on adhesion of industrially applied powder coating, and investigations of a failed painted aluminium window profile due to defects in the extruded profile. Chapters 13 and 14 describe the overall discussion, conclusions and future work based...

Deformation features of aluminium in tensile tests

International Nuclear Information System (INIS)

Quadros, N.F. de.

1984-01-01

It is presented a method to analyse stress-strain curves. Plastic and elastic strains were studied. The strains were done by tensile tests in four types of materials: highly pure aluminium, pure aluminium, commercially pure aluminium and aluminium - uranium. The chemical compositions were obtained by spectroscopy analysis and neutron activation analysis. Tensile tests were carried out at three strain rates, at room temperature, 100,200, 300 and 400 0 C, with knives extensometer and strain-gages to studied the elastic strain region. A multiple spring model based on two springs model to analyse elastic strain caused by tests without extensometers, taking in account moduli of elasticity and, an interactive analysis system with graphic capability were developed. It was suggested a qualitative model to explain the quantized multielasticity of Bell. (M.C.K.) [pt

Dielectric aluminium phosphate thin films. Couches minces dielectriques de phosphate d'aluminium

Energy Technology Data Exchange (ETDEWEB)

Daviero, S. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France)); Avinens, C. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France)); Ibanez, A. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France)); Giuntini, J.C. (Lab. Physicochimie des Materiaux Solides, 34 -Montpellier (France)); Philippot, E. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France))

1993-04-01

Aluminium phosphate thin films on silicium substrate have been carried out from tributylphosphate and aluminium acetylacetonate precursors in solution through the ''pyrosol'' process. It can be observed a large range of chemical analysis in terms of experimental conditions. These thin films have been characterized by X-ray diffraction and infrared spectrometry. Their electrical characteristics, defined from direct current and alternative current measurements, are quite different to those of the crystallized phosphate and can be explained by P-O and Al-O ''dangling bond'' existence. (orig.).

Rapidly solidified aluminium for optical applications

NARCIS (Netherlands)

Gubbels, G.P.H.; Venrooy, B.W.H. van; Bosch, A.J.; Senden, R.

2008-01-01

This paper present the results of a diamond turning study of a rapidly solidified aluminium 6061 alloy grade, known as RSA6061. It is shown that this small grain material can be diamond turned to smaller roughness values than standard AA6061 aluminium grades. Also, the results are nearly as good as

Effects of emission reductions from the smelters in Sudbury on recovery of lakes within the metal deposition zone

Energy Technology Data Exchange (ETDEWEB)

Keller, W.; Heneberry, J.; Clark, M.; Malette, M.; Gunn, J. [Laurentian Univ., Sudbury, ON (Canada) Dept. of Biology

1999-07-01

Recent trends are examined in the chemistry of Sudbury lakes for evidence of further chemical recovery, as well as some of the biological characteristics of recovering Sudbury lakes. Preliminary results are provided from studies investigating physical, chemical and biological factors that may influence the lake recovery process with a focus on the lakes close to Sudbury that were historically the most severely affected. Smelter emission reductions in the Sudbury area have led to substantial changes in the water quality of area lakes, and decreases in acidity, sulfate, and copper and nickel concentrations followed the substantial decreases in emissions during the 1970s and similar trends are continuing after the implementation of large additional smelter emission reductions in the 1990s. Some of the most highly affected lakes close to the Sudbury smelters have showed very dramatic reductions in acidity and metal concentrations during the 1990s. Evaluation of the direct effects of the recent emissions reductions is confounded by the potential continuing effects of previous emission reductions and the effects of weather variations on chemistry time trends in Sudbury lakes. Continued monitoring of Sudbury lakes is essential to evaluate the ultimate effect of emission reduction programs, to develop an understanding of the recovery process, and to determine the need for any additional emission reduction requirements. 38 refs., 7 figs.

[Determination of aluminium in flour foods with photometric method].

Science.gov (United States)

Ma, Lan; Zhao, Xin; Zhou, Shuang; Yang, Dajin

2012-05-01

To establish a determination method for aluminium in flour foods with photometric method. After samples being treated with microwave digestion and wet digestion, aluminium in staple flour foods was determined by photometric method. There was a good linearity of the result in the range of 0.25 - 5.0 microg/ml aluminium, r = 0.9998; limit of detection (LOD) : 2.3 ng/ml; limit of quantitation (LOQ) : 7 ng/ml. This method of determining aluminium in flour foods is simple, rapid and reliable.

Comparison of reactivity to a metallic disc and 2% aluminium salt in 366 children, and reproducibility over time for 241 young adults with childhood vaccine-related aluminium contact allergy.

Science.gov (United States)

Gente Lidholm, Anette; Inerot, Annica; Gillstedt, Martin; Bergfors, Elisabet; Trollfors, Birger

2018-07-01

An aluminium hydroxide-adsorbed pertussis toxoid vaccine was studied in 76 000 children in the 1990s in Gothenburg, Sweden. Long-lasting itchy subcutaneous nodules at the vaccination site were seen in 745 participants. Of 495 children with itchy nodules who were patch tested for aluminium allergy, 377 were positive. In 2007-2008, 241 of the positive children were retested. Only in one third were earlier positive results reproduced. To further describe patch test reactions to different aluminium compounds in children with vaccine-induced aluminium allergy. Positive patch test results for metallic aluminium (empty Finn Chamber) and aluminium chloride hexahydrate 2% petrolatum (pet.) were analysed in 366 children with vaccine-induced persistent itching nodules tested in 1998-2002. Of those, 241 were tested a second time (2007-2008), and the patch test results of the two aluminium preparations were analysed. Patch testing with aluminium chloride hexahydrate 2% pet. is a more sensitive way to diagnose aluminium contact allergy than patch testing with metallic aluminium. A general decrease in the strength of reactions to both aluminium preparations in 241 children tested twice was observed. Aluminium contact allergy can be diagnosed by patch testing without using metallic aluminium. © 2018 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Effect of smelt aluminium on mechanical properties of steels

International Nuclear Information System (INIS)

Ryabov, V.R.; Dykhno, I.S.; Deev, G.F.; Karikh, V.V.

1987-01-01

Effect of smelt aluminium on mechanical properties of armco-iron and 12 Kh18N10T steel is studied. It is stated that in smelt aluminium and aluminium alloy contact with armco-iron the sample ductility is decreased. Corrosion effect of smelt alluminium on (18Kh15N5AM3) steel in the form of reinforced wire in aluminium-steel KAS-1A composite material is investigted. It is stated in experiment that during smelt alluminium-steel contact interaction of heterogeneous phases takes place

Study of corrosion in aluminium using neutron radiography technique

International Nuclear Information System (INIS)

Islam, M.N.; Alam, M.K.; Saklayen, M.A.; Ahsan, M.H.; Islam, S.M.A.; Zaman, M.A.

2000-01-01

Neutron radiography technique has been adopted for detection of corrosion in aluminium by filling artificially made holes on aluminium slab with Al(OH) 3 . The contrast between the optical densities of corrosion products and aluminium slab was assessed from the densitometric measurements. Variation of optical density difference with sample thickness has also been studied. The results confirm that approximately 0.039 mm thick corrosion products having diameter 10 mm can easily be detected in 2 cm thick aluminium slab. The linear attenuation coefficient of Al(OH) 3 has been obtained as 0.9447. From the present investigation it is confirmed that film neutron radiography (NR) technique is helpful for investigation of Al(OH) 3 type corrosion product in aluminium. (author)

Removal of Arsenic from Wastewaters by Airlift Electrocoagulation: Part 3: Copper Smelter Wastewater Treatment

DEFF Research Database (Denmark)

Hansen, H.K.; Ottosen, Lisbeth M.

2010-01-01

The arsenic content in wastewater is of major concern for copper smelters. A typical complex wastewater treatment is needed with a combination of chemical and physical processes. Electrocoagulation (EC) has shown its potential for arsenic removal due to the formation of ferric hydroxide-arsenate ...... threshold value for wastewater discharge could rapidly be reached when the conventional method did not clean the wastewater sufficiently....

Effects of aluminium surface morphology and chemical modification on wettability

Energy Technology Data Exchange (ETDEWEB)

Rahimi, M., E-mail: mar@sbi.aau.dk [Department of Energy and Environment, Danish Building Research Institute, Aalborg University, A.C. Meyers Vænge 15, 2450 København SV (Denmark); Fojan, P.; Gurevich, L. [Department of Physics and Nanotechnology, Aalborg University, Skjernvej 4, DK-9220 Aalborg East (Denmark); Afshari, A. [Department of Energy and Environment, Danish Building Research Institute, Aalborg University, A.C. Meyers Vænge 15, 2450 København SV (Denmark)

2014-03-01

Highlights: • Successful surface modification procedures on aluminium samples were performed involving formation of the layer of hydrophilic hyperbranched polyethyleneglycol (PEG) via in situ polymerization, molecular vapour deposition of a monolayer of fluorinated silane, and a combination of those. • The groups of surfaces with hydrophobic behavior were found to follow the Wenzel model. • A transition from Cassie–Baxter's to Wenzel's regime was observed due to changing of the surface roughness upon mechanical polishing in aluminium samples. - Abstract: Aluminium alloys are some of the predominant metals in industrial applications such as production of heat exchangers, heat pumps. They have high heat conductivity coupled with a low specific weight. In cold working conditions, there is a risk of frost formation on the surface of aluminium in the presence of water vapour, which can lead to the deterioration of equipment performance. This work addresses the methods of surface modification of aluminium and their effect of the underlying surface morphology and wettability, which are the important parameters for frost formation. Three groups of real-life aluminium surfaces of different morphology: unpolished aluminium, polished aluminium, and aluminium foil, were subjected to surface modification procedures which involved the formation of a layer of hydrophilic hyperbranched polyethyleneglycol via in situ polymerization, molecular vapour deposition of a monolayer of fluorinated silane, and a combination of those. The effect of these surface modification techniques on roughness and wettability of the aluminium surfaces was elucidated by ellipsometry, contact angle measurements and atomic force microscopy. We demonstrated that by employing different types of surface modifications the contact angle of water droplets on aluminium samples can be varied from 12° to more than 120°. A crossover from Cassie–Baxter to Wenzel regime upon changing the surface

Spectrophotometric determination of aluminium in steel with xylenol orange

International Nuclear Information System (INIS)

Majeed, A.; Javed, N.; Khan, M.S.

1996-01-01

Spectrophotometric determination of Aluminium in steel based on colour reaction between Aluminium and xylenol orange has been carried out. Red coloured complex formed in weak acidic solution is measured for its absorbance at 550 nm. The various optimum experimental conditions for Aluminium xylenol orange (Al-Xo) complex have been studied. (author)

Wear behavior of carbon fiber/aluminium-composites during abrasive loading; Verschleissverhalten von Kohlenstoffaser/Aluminium-Verbunden unter abrasiver Beanspruchung

Energy Technology Data Exchange (ETDEWEB)

Wielage, B.; Dorner, A. [Technische Univ. Chemnitz (Germany). Lehrstuhl fuer Verbundwerkstoffe

1998-07-01

Abrasive wear resistance of aluminium is significantly improved by the reinforcement with a high volume percentage of carbon fibres. The wear of unreinforced aluminium after scratching by a diamond indenter can be described as pure microgrooving without any micro-chipping. After integration of 70 vol.-% carbon fibers the damage mechanism is considerably altered and a great amount of micro-chipping occurs. The abrasive wear is strongly influenced by the fiber orientation. The best wear resistance is observed when the fibers are orientated perpendicular to the wear surface. (orig.) [Deutsch] Die Verstaerkung von Aluminium mit einem hohen Volumengehalt endloser Kohlenstoffasern verbessert erkennbar dessen Resistenz gegenueber Abrasionsverschleiss. Der Verschleiss von unverstaerktem Aluminium infolge des Ritzens mit einem Diamantindenter erfolgt in Form von reinem Mikrofurchen ohne Spanbildung. Aufgrund der Integration von 70 Vol.-% Kohlenstoffasern wird eine erhebliche Zunahme des Schaedigungsmechanismus Mikrospanen festgestellt. Die Faserorientierung hat merklichen Einfluss auf die Sensibilitaet gegenueber Abrasion. Orientierung der anisotropen Kohlenstoffasern senkrecht zur Verschleissoberflaeche bedingt den geringsten Abrasionsverschleiss. (orig.)

Study of ionic movements during anodic oxidation of nitrogen-implanted aluminium

International Nuclear Information System (INIS)

Terwagne, G.; Lucas, S.; Bodart, F.; Sorensen, G.; Jensen, H.

1990-01-01

In recent years there has been a considerable interest in synthesizing aluminium nitrides by ion implantation in order to modify the tribological properties of aluminium. The growth of an oxide layer by anodic process on these synthesized aluminium nitrides gives an interesting oxide-on-semiconductor material with surprising dynamic and decorative properties. During the anodic oxidation, ionic movements are involved in the near-surface region of the aluminium material; these ionic movements have been studied by Rutherford backscattering spectrometry (RBS) and nuclear reaction analysis (NRA) on thin aluminium foils (7000 A) preimplanted with nitrogen and post-oxidized in an ammonium pentaborate solution. The growth of the oxide layer is reduced when the aluminium is preimplanted with nitrogen: the speed of oxidation depends on the implantation conditions (energy and fluence). Moreover, the aluminium nitride can be dissolved when all metallic aluminium staying between the surface and the AlN are consumed by the anodic process. (orig.)

Diffusion bonding of transition structures for integral aluminium-fibre reinforced polymer (FRP) compounds

Energy Technology Data Exchange (ETDEWEB)

Hehl, A. von [IWT - Stiftung Institut fuer Werkstofftechnik, Hauptabteilung Werkstofftechnik, Bremen (Germany); Syassen, F. [Airbus Operations GmbH, Metal Technology, Bremen (Germany); Schimanski, K.

2012-04-15

Components in hybrid design become more and more important in terms of their lightweight potential. In this context the demand for weight saving in aerospace leads to increasing numbers of applications of fibre composites for primary structural components. In consequence the use of FRP-metal compounds is necessary. Within the investigations of the researcher group ''Schwarz Silber'' (FOR 1224) founded by the DFG (German Research Foundation) material optimised interface structures for advanced CFRP-aluminium compounds are currently being studied. Within their work the researcher group focussed on three concepts realizing the transition structures: the usage of wires (titanium), foils (titanium) and fibres (glass fibre) as transition elements between CFRP and aluminium. For the connection of the aluminium sheet and the transition element die-casting and laser beam welding are basically used. As a possible alternative to the both liquid phase processes a feasibility study haven been done focussing the solid state processes diffusion bonding. The experimental results show the high potential of this process in view of the transferable loads for integral transition structures. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Steam Assisted Accelerated Growth of Oxide Layer on Aluminium Alloys

DEFF Research Database (Denmark)

Din, Rameez Ud; Yuksel, Serkan; Jellesen, Morten Stendahl

2013-01-01

Corrosion resistance of aluminium alloys is related to the composition and morphology of the oxide film on the surface of aluminium. In this paper we investigated the use of steam on the surface modification of aluminium to produce boehmite films. The study reveals a detailed investigation...... of the effect of vapour pressure, structure of intermetallic particles and thickness of boehmite films on the corrosion behaviour of aluminium alloys....

Evidence-based integrated environmental solutions for secondary lead smelters: Pollution prevention and waste minimization technologies and practices

Energy Technology Data Exchange (ETDEWEB)

Genaidy, A.M., E-mail: world_tek_inc@yahoo.com [University of Cincinnati, Cincinnati, Ohio (United States); Sequeira, R. [University of Cincinnati, Cincinnati, Ohio (United States); Tolaymat, T. [U.S. Environmental Protection Agency, Office of Research and Development, Cincinnati, Ohio (United States); Kohler, J. [US Environmental Protection Agency, Office of Solid Waste and Emergency Response, Washington DC (United States); Rinder, M. [WorldTek Inc, Cincinnati (United States)

2009-05-01

An evidence-based methodology was adopted in this research to establish strategies to increase lead recovery and recycling via a systematic review and critical appraisal of the published literature. In particular, the research examines pollution prevention and waste minimization practices and technologies that meet the following criteria: (a) reduce/recover/recycle the largest quantities of lead currently being disposed of as waste, (b) technically and economically viable, that is, ready to be diffused and easily transferable, and (c) strong industry interest (i.e., industry would consider implementing projects with higher payback periods). The following specific aims are designed to achieve the study objectives: Aim 1 - To describe the recycling process of recovering refined lead from scrap; Aim 2 - To document pollution prevention and waste management technologies and practices adopted by US stakeholders along the trajectory of LAB and lead product life cycle; Aim 3 - To explore improved practices and technologies which are employed by other organizations with an emphasis on the aforementioned criteria; Aim 4 - To demonstrate the economic and environmental costs and benefits of applying improved technologies and practices to existing US smelting operations; and Aim 5 - To evaluate improved environmental technologies and practices using an algorithm that integrates quantitative and qualitative criteria. The process of identifying relevant articles and reports was documented. The description of evidence was presented for current practices and technologies used by US smelters as well as improved practices and technologies. Options for integrated environmental solutions for secondary smelters were introduced and rank ordered on the basis of costs (i.e., capital investment) and benefits (i.e., production increases, energy and flux savings, and reduction of SO2 and slag). An example was provided to demonstrate the utility of the algorithm by detailing the costs and

Evidence-based integrated environmental solutions for secondary lead smelters: pollution prevention and waste minimization technologies and practices.

Science.gov (United States)

Genaidy, A M; Sequeira, R; Tolaymat, T; Kohler, J; Rinder, M

2009-05-01

An evidence-based methodology was adopted in this research to establish strategies to increase lead recovery and recycling via a systematic review and critical appraisal of the published literature. In particular, the research examines pollution prevention and waste minimization practices and technologies that meet the following criteria: (a) reduce/recover/recycle the largest quantities of lead currently being disposed of as waste, (b) technically and economically viable, that is, ready to be diffused and easily transferable, and (c) strong industry interest (i.e., industry would consider implementing projects with higher payback periods). The following specific aims are designed to achieve the study objectives: Aim 1 - To describe the recycling process of recovering refined lead from scrap; Aim 2 - To document pollution prevention and waste management technologies and practices adopted by US stakeholders along the trajectory of LAB and lead product life cycle; Aim 3 - To explore improved practices and technologies which are employed by other organizations with an emphasis on the aforementioned criteria; Aim 4 - To demonstrate the economic and environmental costs and benefits of applying improved technologies and practices to existing US smelting operations; and Aim 5 - To evaluate improved environmental technologies and practices using an algorithm that integrates quantitative and qualitative criteria. The process of identifying relevant articles and reports was documented. The description of evidence was presented for current practices and technologies used by US smelters as well as improved practices and technologies. Options for integrated environmental solutions for secondary smelters were introduced and rank ordered on the basis of costs (i.e., capital investment) and benefits (i.e., production increases, energy and flux savings, and reduction of SO(2) and slag). An example was provided to demonstrate the utility of the algorithm by detailing the costs and

Corrosion behaviour of borated aluminium used as neutron absorber

Energy Technology Data Exchange (ETDEWEB)

Emmerich, R. [EaglePicher Technologies GmbH, Oehringen (Germany); Ensinger, W.; Enders, B. [Philipps-Univ. of Marburg, Dept. of Chemistry, Material Science Centre (Germany)

2004-07-01

The electrochemical behaviour of pure and borated aluminium was examined. Measurements were performed in two different electrolytes at 90 C containing different trace-amounts of chloride. For borated aluminium current transients, i.e. metastable depassivation events were found. It is suggested to attribute these transients to less stable passivation layers in comparison to pure aluminium.

Effects of Aluminium Sulfate on Cadmium Accumulation in Rice

International Nuclear Information System (INIS)

Khamvarn, Vararas; Boontanon, Narin; Prapagdee, Benjaphorn; Kumsopa, Acharaporn; Boonsirichai, Kanokporn

2011-06-01

Full text: Cadmium accumulation in Pathum Thani 1 and Suphan Buri 60 rice cultivars was investigated upon treatment with aluminium sulfate as a precipitant. Rice was grown hydroponically in a medium containing 4 ppm cadmium nitrate with or without 4 ppm aluminium sulfate. Root, stem with leaves and grain samples were collected and analyzed for cadmium content using atomic absorption spectroscopy and inductively coupled plasma atomic emission spectroscopy. Without the addition of aluminium sulfate, Pathum Thani 1 and Suphan Buri 60 accumulated 24.71∫ 3.14 ppm and 34.43 ∫ 4.51 ppm (dry weight of whole plant) of cadmium, respectively. With aluminium sulfate, cadmium accumulation increased to 40.66 ∫ 2.47 ppm and 62.94 ∫ 10.69 ppm, respectively. The addition of aluminium sulfate to the planting medium did not reduce cadmium accumulation but caused the rice to accumulate more cadmium especially in the shoots and grains. This observation might serve as the basis for future research on the management of agricultural areas that are contaminated with cadmium and aluminium

Volatilisation and oxidation of aluminium scraps fed into incineration furnaces

International Nuclear Information System (INIS)

Biganzoli, Laura; Gorla, Leopoldo; Nessi, Simone; Grosso, Mario

2012-01-01

Highlights: ► Aluminium packaging partitioning in MSW incineration residues is evaluated. ► The amount of aluminium packaging recoverable from the bottom ashes is evaluated. ► Aluminium packaging oxidation rate in the residues of MSW incineration is evaluated. ► 80% of aluminium cans, 51% of trays and 27% of foils can be recovered from bottom ashes. - Abstract: Ferrous and non-ferrous metal scraps are increasingly recovered from municipal solid waste incineration bottom ash and used in the production of secondary steel and aluminium. However, during the incineration process, metal scraps contained in the waste undergo volatilisation and oxidation processes, which determine a loss of their recoverable mass. The present paper evaluates the behaviour of different types of aluminium packaging materials in a full-scale waste to energy plant during standard operation. Their partitioning and oxidation level in the residues of the incineration process are evaluated, together with the amount of potentially recoverable aluminium. About 80% of post-consumer cans, 51% of trays and 27% of foils can be recovered through an advanced treatment of bottom ash combined with a melting process in the saline furnace for the production of secondary aluminium. The residual amount of aluminium concentrates in the fly ash or in the fine fraction of the bottom ash and its recovery is virtually impossible using the current eddy current separation technology. The average oxidation levels of the aluminium in the residues of the incineration process is equal to 9.2% for cans, 17.4% for trays and 58.8% for foils. The differences between the tested packaging materials are related to their thickness, mechanical strength and to the alloy.

Electron Conditioning of Technical Aluminium Surfaces

Energy Technology Data Exchange (ETDEWEB)

Le Pimpec, F

2004-09-02

The effect of electron conditioning on commercially aluminium alloys 1100 and 6063 were investigated. Contrary to the assumption that electron conditioning, if performed long enough, can reduce and stabilize the SEY to low values (= 1.3, value of many pure elements [1]), the SEY of aluminium did not go lower than 1.8. In fact, it reincreases with continued electron exposure dose.

Microstructures in the 6060 aluminium alloy after various severe plastic deformation treatments

International Nuclear Information System (INIS)

Adamczyk-Cieslak, Boguslawa; Mizera, Jaroslaw; Kurzydlowski, Krzysztof Jan

2011-01-01

This paper presents the results concerning the microstructural refinement of the industrial 6060 aluminium alloy processed by severe plastic deformation (SPD). The high level of plastic deformation was achieved using the three methods: hydrostatic extrusion (HE), equal channel angular extrusion (ECAE) and extrusion torsion (ET), which differed in the dynamics of the loading, intensity and homogeneity of the plastic strain field. Microstructure analyses were performed before and after SPD deformation using a transmission (TEM) and a scanning electron microscope (SEM). The refined microstructures were examined qualitatively and quantitatively by the stereological methods and computer image analyses. The microstructure of the industrial 6060 aluminium alloy after deformation was characterized by an average grain size of about 0.4 μm. The results show that the precipitates strongly affect the degree of refinement and the mechanism of microstructural transformations. During the SPD, the second phase particles break apart and homogenize. The HE method generates the largest increase of the volume fraction of the small primary particles. Moreover, the HE process is most effective in reducing the primary particle size. During HE and ECAE processes the second phase precipitates dissolve partially and change their shape. - Research Highlights: → SPD results in a significant increase in the density of the small primary particles. → SPD homogenizes the particle size distribution. → HE and ECAE processes bring nano-grains in the vicinity of the primary particles. → HE and ECAE processing results in the β' precipitates partial dissolutions. → During HE and ECAE processes the β' particles change their shape.

78 FR 25185 - Delegation of New Source Performance Standards and National Emission Standards for Hazardous Air...

Science.gov (United States)

2013-04-30

... Sewage Treatment Plants X X X X P Primary Copper Smelters X X X X Q Primary Zinc Smelters X X X X R Primary Lead Smelters X X X X S Primary Aluminum Reduction Plants.... X X X X T Phosphate Fertilizer Industry: Wet X X X X Process Phosphoric Acid Plants. U Phosphate Fertilizer Industry: X X X X...

Aluminium leaching from red mud by filamentous fungi.

Science.gov (United States)

Urík, Martin; Bujdoš, Marek; Milová-Žiaková, Barbora; Mikušová, Petra; Slovák, Marek; Matúš, Peter

2015-11-01

This contribution investigates the efficient and environmentally friendly aluminium leaching from red mud (bauxite residue) by 17 species of filamentous fungi. Bioleaching experiments were examined in batch cultures with the red mud in static, 7-day cultivation. The most efficient fungal strains in aluminium bioleaching were Penicillium crustosum G-140 and Aspergillus niger G-10. The A. niger G-10 strain was capable to extract up to approximately 141 mg·L(-1) of aluminium from 0.2 g dry weight red mud. Chemical leaching with organic acids mixture, prepared according to A. niger G-10 strain's respective fungal excretion during cultivation, proved that organic acids significantly contribute to aluminium solubilization from red mud. Copyright © 2015 Elsevier Inc. All rights reserved.

Determination of ultratrace amounts of uranium and thorium in aluminium and aluminium alloys by electrothermal vaporization/ICP-MS

International Nuclear Information System (INIS)

Nakamura, Yasushi; Kobayashi, Yoshio; Kakurai, Yousuke

1993-01-01

A method has been developed for determining the 0.01 ng g -1 level of uranium and thorium in aluminium and aluminium alloys by electrothermal vaporization (ETV)/ICP-MS. This method was found to be significantly interfered with any matrices or other elements contained. An ion-exchange technique was therefore applied to separate uranium and thorium from aluminium and other elements. It was known that uranium are adsorbed on an anion-exchange resin and thorium are adsorbed on cation-exchange resin. However, aluminium and copper were eluted with 6 M hydrochloric acid. Dissolve the sample with hydrochloric acid containing copper which was added for analysis of pure aluminium, and oxidize with hydrogen peroxide. Concentration of hydrochloric acid in the solution was adjusted to 6 M, and then passed the solution through the mixed ion-exchange resin column. After the uranium and thorium were eluted with 1 M hydrofluoric acid-0.1 M hydrochloric acid, the solution was evaporated to dryness. It was then dissolved with 1 M hydrochloric acid. Uranium and thorium were analyzed by ETV/ICP-MS using tungsten and molybdenum boats, respectively, since the tungsten boat contained high-level thorium and the molybdenum boat contained uranium. The determination limit of uranium and thorium were 0.003 and 0.005 ng g -1 , respectively. (author)

Investigations concerning the effect of aluminium toxicity on the physiology and fine structures of oat plants. Physiologische und feinstrukturelle Untersuchungen zur Aluminium-Toxizitaet an Haferpflanzen

Energy Technology Data Exchange (ETDEWEB)

Marienfeld, S.

1992-06-30

In order to test the toxicity of aluminium to plants, two-week-old oat seedlings were exposed to aluminium concentrations of 0-400 [mu]M in the culture broth. Already after 12-24 hours a decrease in longitudinal root growth is to be noted, resulting from impaired mitosis activity of the root tip. This, and the observed premature cell differentiation are not aluminium-specific but unspecific reactions to unfavourable conditions. Shoot growth is only reduced after 3-4 days, and less so. Magnesium and calcium fertilization did enhance the growth of aluminium-stressed plants, but not to the level of the control plants, although the mineral concentration in the leaves reached normal values. Phosphate concentration in the root increased because of aluminium phosphate precipitation in the cell walls, which has detoxifying effect along with aluminium fixation to negative charges in the cell walls. Aluminium remains almost quantitatively in the cell wall area of the roots and is not accumulated in the cell core. Aluminium stress causes transpiration and CO[sub 2] uptake to be impaired as a reaction to the growth depression in the root area, even before the mineral concentration in the shoots is lowered. Later there follow chlorophyll depletion, chloroplast degradation, and a reduction of the leaf area. (UWA)

Friction stir welding (FSW of aluminium foam sandwich panels

Directory of Open Access Journals (Sweden)

M. Bušić

2016-07-01

Full Text Available The article focuses on the influence of welding speed and tool tilt angle upon the mechanical properties at the friction stir welding of aluminium foam sandwich panels. Double side welding was used for producing butt welds of aluminium sandwich panels applying insertion of extruded aluminium profile. Such insertion provided lower pressure of the tool upon the aluminium panels, providing also sufficient volume of the material required for the weldment formation. Ultimate tensile strength and flexural strength for three-point bending test have been determined for samples taken from the welded joints. Results have confirmed anticipated effects of independent variables.

Isotopic characterisation of lead in contaminated soils from the vicinity of a non-ferrous metal smelter near Plovdiv, Bulgaria

Energy Technology Data Exchange (ETDEWEB)

Bacon, Jeffrey R. [Macaulay Institute, Craigiebuckler, Aberdeen AB15 8QH (United Kingdom)]. E-mail: j.bacon@macaulay.ac.uk; Dinev, Nikolai S. [N Poushkarov Institute of Soil Science and Agroecology, Sofia (Bulgaria)

2005-03-01

Soil samples from the vicinity of a non-ferrous metal smelter near Plovdiv, Bulgaria contained very high concentrations of cadmium, lead and zinc (up to 140, 4900 and 5900 mg kg{sup -1}, respectively). A roadside soil in a relatively uncontaminated area also contained high concentrations of the same metals (24, 1550 and 1870 mg kg{sup -1}, respectively) indicating that the transport of ores could be a source of contamination. Even though the lead isotope ratios in all the samples fell within a very narrow range (for example, 1.186-1.195 for {sup 206}Pb/{sup 207}Pb), the samples could be differentiated into three distinct groups: ores ({sup 206}Pb/{sup 207}Pb and {sup 208}Pb/{sup 207}Pb ratios of 1.1874-1.1884 and 2.4755-2.4807, respectively), current deposition (1.1864 and 2.4704-2.4711, respectively) and local background (1.1927-1.1951 and 2.4772-2.4809, respectively). Although most of the current deposition has its origin in the ores used at the smelter, up to 12% could be from other sources such as petrol lead. - Although soils in the vicinity of a non-ferrous metal smelter near Plovdiv, Bulgaria, have become highly contaminated with the ores used, lead isotope analysis has revealed that up to 12% of current deposition could be from other sources such as petrol lead.

Isotopic characterisation of lead in contaminated soils from the vicinity of a non-ferrous metal smelter near Plovdiv, Bulgaria

International Nuclear Information System (INIS)

Bacon, Jeffrey R.; Dinev, Nikolai S.

2005-01-01

Soil samples from the vicinity of a non-ferrous metal smelter near Plovdiv, Bulgaria contained very high concentrations of cadmium, lead and zinc (up to 140, 4900 and 5900 mg kg -1 , respectively). A roadside soil in a relatively uncontaminated area also contained high concentrations of the same metals (24, 1550 and 1870 mg kg -1 , respectively) indicating that the transport of ores could be a source of contamination. Even though the lead isotope ratios in all the samples fell within a very narrow range (for example, 1.186-1.195 for 206 Pb/ 207 Pb), the samples could be differentiated into three distinct groups: ores ( 206 Pb/ 207 Pb and 208 Pb/ 207 Pb ratios of 1.1874-1.1884 and 2.4755-2.4807, respectively), current deposition (1.1864 and 2.4704-2.4711, respectively) and local background (1.1927-1.1951 and 2.4772-2.4809, respectively). Although most of the current deposition has its origin in the ores used at the smelter, up to 12% could be from other sources such as petrol lead. - Although soils in the vicinity of a non-ferrous metal smelter near Plovdiv, Bulgaria, have become highly contaminated with the ores used, lead isotope analysis has revealed that up to 12% of current deposition could be from other sources such as petrol lead

Surface treatments for aluminium alloys

Science.gov (United States)

Ardelean, M.; Lascău, S.; Ardelean, E.; Josan, A.

2018-01-01

Typically, in contact with the atmosphere, the aluminium surface is covered with an aluminium oxide layer, with a thickness of less than 1-2μm. Due to its low thickness, high porosity and low mechanical strength, this layer does not protect the metal from corrosion. Anodizing for protective and decorative purposes is the most common method of superficial oxidation processes and is carried out through anodic oxidation. The oxide films, resulted from anodizing, are porous, have a thickness of 20-50μm, and are heat-resistant, stable to water vapour and other corrosion agents. Hard anodizing complies with the same obtains principles as well as decorative and protective anodization. The difference is in that hard anodizing is achieved at low temperatures and high intensity of electric current. In the paper are presented the results of decorative and hard anodization for specimens made from several aluminium alloys in terms of the appearance of the specimens and of the thickness of the anodized.

Aluminium/iron reinforced polyfurfuryl alcohol resin as advanced biocomposites

Directory of Open Access Journals (Sweden)

Rakesh Kumar

2016-07-01

Full Text Available Aluminium and iron are widely used in construction sectors for the preparation of advanced composites with epoxy resins as matrices. In recent times, there are several reports on the polymerization of polyfufuryl alcohol (PFA a thermoset bioresins from furfuryl alcohol (FA. FA is obtained from waste of sugarcane bagasse. In this work, first the possibility of curing PFA from FA in the presence of aluminium or iron has been explored. Absorbance results from colorimeter/spectrophotometerindicated that the curing of FA to PFA in presence of aluminium started easily while in presence of iron the curing of FA to PFA could not start. Based on the above results, aluminium wire reinforced composites were successfully prepared with three different weight fractions (0.13, 0.09 and 0.07 of aluminium wire. The mechanical properties of these composites were determined theoretically and reported.

Volatilisation and oxidation of aluminium scraps fed into incineration furnaces

Energy Technology Data Exchange (ETDEWEB)

Biganzoli, Laura, E-mail: laura.biganzoli@mail.polimi.it [Politecnico di Milano, Piazza L. Da Vinci 32, 20133 Milano (Italy); Gorla, Leopoldo; Nessi, Simone; Grosso, Mario [Politecnico di Milano, Piazza L. Da Vinci 32, 20133 Milano (Italy)

2012-12-15

Highlights: Black-Right-Pointing-Pointer Aluminium packaging partitioning in MSW incineration residues is evaluated. Black-Right-Pointing-Pointer The amount of aluminium packaging recoverable from the bottom ashes is evaluated. Black-Right-Pointing-Pointer Aluminium packaging oxidation rate in the residues of MSW incineration is evaluated. Black-Right-Pointing-Pointer 80% of aluminium cans, 51% of trays and 27% of foils can be recovered from bottom ashes. - Abstract: Ferrous and non-ferrous metal scraps are increasingly recovered from municipal solid waste incineration bottom ash and used in the production of secondary steel and aluminium. However, during the incineration process, metal scraps contained in the waste undergo volatilisation and oxidation processes, which determine a loss of their recoverable mass. The present paper evaluates the behaviour of different types of aluminium packaging materials in a full-scale waste to energy plant during standard operation. Their partitioning and oxidation level in the residues of the incineration process are evaluated, together with the amount of potentially recoverable aluminium. About 80% of post-consumer cans, 51% of trays and 27% of foils can be recovered through an advanced treatment of bottom ash combined with a melting process in the saline furnace for the production of secondary aluminium. The residual amount of aluminium concentrates in the fly ash or in the fine fraction of the bottom ash and its recovery is virtually impossible using the current eddy current separation technology. The average oxidation levels of the aluminium in the residues of the incineration process is equal to 9.2% for cans, 17.4% for trays and 58.8% for foils. The differences between the tested packaging materials are related to their thickness, mechanical strength and to the alloy.

Aluminium allergy and granulomas induced by vaccinations for children

DEFF Research Database (Denmark)

Andersen, Rosa Marie O; Zachariae, Claus; Johansen, Jeanne Duus

2014-01-01

Vaccination with aluminium-adsorbed vaccines can induce aluminium allergy with persistent itching subcutaneous nodules at the injection site - vaccination granulomas. In this article we give an overview of childhood aluminium-adsorbed vaccines available in Denmark. Through literature studies we...... examine the incidence, the symptoms and the prognosis for the vaccination granulomas and the allergy. Finally we discuss the status in Denmark....

Hot workability of aluminium alloys

International Nuclear Information System (INIS)

Yoo, Yeon Chul; Oh, Kyung Jin

1986-01-01

Hot Workability of aluminium alloys, 2024, 6061 and 7075, has been studied by hot torsion tests at temperatures from 320 to 515 deg C and at strain rates from 1.26 x 10 -3 to 5.71 x 10 -3 sec -1 . Hot working condition of these aluminium alloys was determined quantitatively from the constitutive equations obtained from flow stress curves in torsion. Experimental data of the logarith of the Zener-Hollomonn parameter showed good linear relationships to the logarith of sinh(ασ-bar)

Aluminium toxicity tolerance in crop plants: Present status of research

African Journals Online (AJOL)

... tolerance of which genes of the Aluminium-activated malate transporter (ALMT) and multidrug and toxic compound extrusion (MATE) families are prominent. In this review, the progress of research in identifying aluminium toxicity tolerant genes is discussed. Keywords: Aluminium toxicity, soil acidity, hydroponic screening, ...

Compressive Behaviour and Energy Absorption of Aluminium Foam Sandwich

Science.gov (United States)

Endut, N. A.; Hazza, M. H. F. Al; Sidek, A. A.; Adesta, E. T. Y.; Ibrahim, N. A.

2018-01-01

Development of materials in automotive industries plays an important role in order to retain the safety, performance and cost. Metal foams are one of the idea to evolve new material in automotive industries since it can absorb energy when it deformed and good for crash management. Recently, new technology had been introduced to replace metallic foam by using aluminium foam sandwich (AFS) due to lightweight and high energy absorption behaviour. Therefore, this paper provides reliable data that can be used to analyze the energy absorption behaviour of aluminium foam sandwich by conducting experimental work which is compression test. Six experiments of the compression test were carried out to analyze the stress-strain relationship in terms of energy absorption behavior. The effects of input variables include varying the thickness of aluminium foam core and aluminium sheets on energy absorption behavior were evaluated comprehensively. Stress-strain relationship curves was used for energy absorption of aluminium foam sandwich calculation. The result highlights that the energy absorption of aluminium foam sandwich increases from 12.74 J to 64.42 J respectively with increasing the foam and skin thickness.

Investigation of different anode materials for aluminium rechargeable batteries

Science.gov (United States)

Muñoz-Torrero, David; Leung, Puiki; García-Quismondo, Enrique; Ventosa, Edgar; Anderson, Marc; Palma, Jesús; Marcilla, Rebeca

2018-01-01

In order to shed some light into the importance of the anodic reaction in reversible aluminium batteries, we investigate here the electrodeposition of aluminium in an ionic liquid electrolyte (BMImCl-AlCl3) using different substrates. We explore the influence of the type of anodic material (aluminium, stainless steel and carbon) and its 3D geometry on the reversibility of the anodic reaction by cyclic voltammetry (CV) and galvanostatic charge-discharge. The shape of the CVs confirms that electrodeposition of aluminium was feasible in the three materials but the highest peak currents and smallest peak separation in the CV of the aluminium anode suggested that this material was the most promising. Interestingly, carbon-based substrates appeared as an interesting alternative due to the high peak currents in CV, moderate overpotentials and dual role as anode and cathode. 3D substrates such as fiber-based carbon paper and aluminium mesh showed significantly smaller overpotentials and higher efficiencies for Al reaction suggesting that the use of 3D substrates in full batteries might result in enhanced power. This is corroborated by polarization testing of full Al-batteries.

Aluminium Electroplating on Steel from a Fused Bromide Electrolyte

Energy Technology Data Exchange (ETDEWEB)

Prabhat Tripathy; Laura Wurth; Eric Dufek; Toni Y. Gutknecht; Natalie Gese; Paula Hahn; Steven Frank; Guy Fredrickson; J Stephen Herring

2014-08-01

A quaternary bromide bath (LiBr-KBr-CsBr-AlBr3) was used to electro-coat aluminium on steel substrates. The electrolyte was prepared by the addition of AlBr3 into the eutectic LiBr-KBr-CsBr melt. A smooth, thick, adherent and shiny aluminium coating could be obtained with 80 wt.% AlBr3 in the ternary melt. The SEM photographs of the coated surfaces suggest the formation of thick and dense coatings with good aluminium coverage. Both salt immersion and open circuit potential measurement suggest that the coatings did display good corrosion-resistance behavior. Annealing of the coated surfaces, prior to corrosion tests, suggested the robustness of the metallic aluminium coating in preventing the corrosion of the steel surfaces. Studies also indicated that the quaternary bromide plating bath can potentially provide a better aluminium coating on both ferrous and non-ferrous metals, including complex surfaces/geometries.

Characterisation and concentration profile of aluminium during ...

African Journals Online (AJOL)

An aluminium(Al) characterisation study was conducted at a surface water treatment plant (Buffalo Pound Water Treatment Plant (BPWTP) in Moose Jaw, Saskatchewan, Canada) to understand better the effect of alum coagulant on various Al fractions. The raw water source for BPWTP is Buffalo Pound Lake water. The Al ...

Feet sunk in molten aluminium: The burn and its prevention.

Science.gov (United States)

Alonso-Peña, David; Arnáiz-García, María Elena; Valero-Gasalla, Javier Luis; Arnáiz-García, Ana María; Campillo-Campaña, Ramón; Alonso-Peña, Javier; González-Santos, Jose María; Fernández-Díaz, Alaska Leonor; Arnáiz, Javier

2015-08-01

Nowadays, despite improvements in safety rules and inspections in the metal industry, foundry workers are not free from burn accidents. Injuries caused by molten metals include burns secondary to molten iron, aluminium, zinc, copper, brass, bronze, manganese, lead and steel. Molten aluminium is one of the most common causative agents of burns (60%); however, only a few publications exist concerning injuries from molten aluminium. The main mechanisms of lesion from molten aluminium include direct contact of the molten metal with the skin or through safety apparel, or when the metal splash burns through the pants and rolls downward along the leg. Herein, we report three cases of deep dermal burns after 'soaking' the foot in liquid aluminium and its evolutive features. This paper aims to show our experience in the management of burns due to molten aluminium. We describe the current management principles and the key features of injury prevention. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

Corrosion of Metal-Matrix Composites with Aluminium Alloy Substrate

Directory of Open Access Journals (Sweden)

B. Bobic

2010-03-01

Full Text Available The corrosion behaviour of MMCs with aluminium alloy matrix was presented. The corrosion characteristics of boron-, graphite-, silicon carbide-, alumina- and mica- reinforced aluminium MMCs were reviewed. The reinforcing phase influence on MMCs corrosion rate as well as on various corrosion forms (galvanic, pitting, stress corrosion cracking, corrosion fatique, tribocorrosion was discussed. Some corrosion protection methods of aluminium based MMCs were described

Cold forming of aluminium - State of the art

DEFF Research Database (Denmark)

Bay, Niels

1997-01-01

The ongoing development of cold forging technology has been manifested lately by the increasing application of components in cold forged aluminium alloys. Applying precipitation hardening alloys components with great strength/weight ratio can be produced with a strength comparable...... to that of unalloyed steel. After description of the different types of alloys and their individual properties and applications, the special requirements for tool design by cold forging in aluminium is discussed. Finally, a large number of industrial examples on cold forged aluminium components are presented. (C) 1997...

Effect of pressurized steam on AA1050 aluminium

DEFF Research Database (Denmark)

Jariyaboon, Manthana; Møller, Per; Ambat, Rajan

2012-01-01

Purpose - The purpose of this paper is to understand the effect of pressurized steam on surface changes, structures of intermetallic particles and corrosion behavior of AA1050 aluminium. Design/methodology/approach - Industrially pure aluminium (AA1050, 99.5 per cent) surfaces were exposed...... reactivities was observed due to the formation of the compact oxide layer. Originality/value - This paper reveals a detailed investigation of how pressurized steam can affect the corrosion behaviour of AA1050 aluminium and the structure of Fe-containing intermetallic particles....

Characterization of aluminium alloys rapidly solidified

International Nuclear Information System (INIS)

Monteiro, W.A.

1988-01-01

This paper discussed the investigation of the microstructural and mechanical properties of the aluminium alloys (3003; 7050; Al-9% Mg) rapidly solidified by melt spinning process (cooling rate 10 4 - 10 6 K/s). The rapidly solidification process of the studied aluminium alloys brought a microcrystallinity, a minimum presence of coarse precipitation and, also, better mechanical properties of them comparing to the same alloys using ingot process. (author) [pt

Sinter aluminium as cladding material for fuel elements; Aluminium fritte comme materiau de gainage pour les elements combustibles

Energy Technology Data Exchange (ETDEWEB)

Mann, K E; Boudouresques, M B [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Otto Fuchs, Meinerzhagen, Westfalen (Germany)

1961-07-01

1. Survey of the production process of sinter aluminium. 2. Description of the forming processes (extrusion, forging and rolling), whereby the production of tubing for atom piles will be explained in detail. 3. Production of ribbed tubes and tubes with close tolerances of sizes. 4. The different SAP-qualities and their properties under special consideration of the properties at elevated temperatures and the creep properties. 5. Diffusion behaviour of SAP with Be, Mg, Al, U and UO{sub 2}. 6. Corrosion behaviour in CO{sub 2} atmosphere at high temperature and in water. 7. Weldability. 8. Effect of irradiation on the mechanical properties. 9. Superiority of SAP compared with normal wrought alloys of the same composition. (author) [French] 1. Apercu des processus de production de l'aluminium fritte. 2. Expose des operations de transformation (filageries, forgeage et laminage), avec explication detaillee de la fabrication de gaine pour reacteurs. 3. Fabrication de tubes canneles et de tubes avec de faibles tolerances. 4. Diverses proprietes de l'aluminium fritte SAP, notamment proprietes aux temperatures elevees et proprietes de fluage. 5. Diffusion de l'aluminium fritte SAP en presence de Be, Mg, Al, U et UO{sub 2}. 6. Resistance a la corrosion dans une atmosphere de CO{sub 2} a temperature elevee et dans l'eau. 7. Possibilites de soudage. 8. Effet de l'irradiation sur les proprietes mecaniques. 9. Superiorite de l'aluminium fritte SAP sur les alliages forges normaux de meme composition. (auteur)

Low temperature oxidation of niobium alloy with silicon-aluminium coating

International Nuclear Information System (INIS)

Lazarev, Eh.M.; Sapozhnikova, L.V.; Shabanova, M.E.; Pod'yachev, V.N.; Kornilova, Z.I.

1987-01-01

Using the gravimetry methods heat resistance of niobium-titanium-aluminium alloy in the air and at 700 deg C in the initial state and when it is protected by silicide-aluminium coatings (with variable content of aluminium) is investigated. Using X-ray diffraction and micro X-ray diffraction analyses, mechanisms of the alloy oxidation and the coating protective effect are studied. The role of aluminium in the formation of coatings is analyzed and according to bend tests the plasticity of the coatings is evaluated

The structure of high-quality aluminium cast iron

Directory of Open Access Journals (Sweden)

D. Kopyciński

2012-01-01

Full Text Available In this study presents the analyse of aluminium iron cast structure (as-cast condition which are used in high temperature. While producing the casts of aluminium iron major influence has been preserve the structure of technological process parameters. The addition to Fe-C-Al alloy V, Ti, Cr leads to the improvement of functional and mechanical cast qualities. In this study, a method was investigated to eliminate the presence of undesirable Al4C3 phases in a aluminium cast iron structure and thus improve the production process. V and Ti additions in aluminium cast iron allows to development of FeAl - VC or TiC alloys. In particular, V or Ti contents above 5 wt.% were found to totally eliminate the presence of Al4C3. In addition, preliminary work indicates that the alloy with the FeAl - VC or TiC structure reveals high oxidation resistance. The introduction of 5 wt.% chromium to aluminium cast iron strengthened Al4C3 precipitate. Thus, the resultant alloy can be considered an intermetallic FeAl matrix strengthened by VC and TiC or modified Al4C3 reinforcements.

Long term insight into biodiversity of a smelter wasteland reclaimed with biosolids and by-product lime.

Science.gov (United States)

Siebielec, Sylwia; Siebielec, Grzegorz; Stuczyński, Tomasz; Sugier, Piotr; Grzęda, Emilia; Grządziel, Jarosław

2018-09-15

Smelter wastelands containing high amounts of zinc, lead, cadmium, and arsenic constitute a major problem worldwide. Serious hazards for human health and ecosystem functioning are related to a lack of vegetative cover, causing fugitive dust fluxes, runoff and leaching of metals, affecting post-industrial ecosystems, often in heavily populated areas. Previous studies demonstrated the short term effectiveness of assisted phytostabilisation of zinc and lead smelter slags, using biosolids and liming. However, a long term persistence of plant communities introduced for remediation and risk reduction has not been adequately evaluated. The work was aimed at characterising trace element solubility, plant and microbial communities of the top layer of the reclaimed zinc and lead smelter waste heaps in Piekary Slaskie, Poland, 20 years after the treatment and revegetation. The surface layer of the waste heaps treated with various rates of biosolids and the by-product lime was sampled for measuring chemical and biochemical parameters, which are indicative for metals bioavailability as well as for microorganisms activity. Microbial processes were characterised by enzyme activities, abundance of specific groups of microorganisms and identification of N fixing bacteria. Plant communities of the area were characterised by a percent coverage of the surface and by a composition of plant species and plant diversity. The study provides a strong evidence that the implemented remediation approach enables a sustainable functioning of the ecosystem established on the toxic waste heaps. Enzyme activities and the count of various groups of microorganisms were the highest in areas treated with both biosolids and lime, regardless their rates. A high plant species diversity and microbial activities are sustainable after almost two decades from the treatment, which is indicative of a strong resistance of the established ecosystem to a metal stress and a poor physical quality of the

Method of preparing an Al-Ti-B grain refiner for aluminium-comprising products, and a method of casting aluminium products

NARCIS (Netherlands)

Brinkman, H.J.; Duszczyk, J.; Katgerman, L.

1999-01-01

The invention relates to a method of preparing an Al-Ti-B grain refiner for cast aluminium-comprising products. According to the invention the preparation is realized by mixing powders selected from the group comprising aluminium, titanium, boron, and alloys and intermetallic compounds thereof,

Mercury deposition/accumulation rates in the vicinity of a lead smelter as recorded by a peat deposit

Czech Academy of Sciences Publication Activity Database

Ettler, V.; Navrátil, Tomáš; Mihaljevič, M.; Rohovec, Jan; Zuna, M.; Šebek, O.; Strnad, L.; Hojdová, Maria

2008-01-01

Roč. 42, č. 24 (2008), s. 5968-5977 ISSN 1352-2310 R&D Projects: GA ČR GP526/07/P170 Institutional research plan: CEZ:AV0Z30130516 Keywords : mercury * deposition * Pb Smelter, * peat * historical record Subject RIV: DD - Geochemistry Impact factor: 2.890, year: 2008

Smelters as Analogs for a Volcanic Eruption at Yucca Mountain

International Nuclear Information System (INIS)

Ross, Benjamin

2004-01-01

The distribution of trace radionuclides in secondary metal smelters provides an analog for spent fuel released from packages during a volcanic eruption. The fraction of the inventory of a radionuclide that would be released into the air in a volcanic eruption is called the dust partitioning factor. In consequence analyses of a volcanic eruption at Yucca Mountain, a value of one has been used for this parameter for all elements. This value is too high for the refractory elements. Reducing the dust partitioning factor for refractory elements to a value equal to the fraction of the magma that becomes ash would still yield conservative estimates of how much radioactivity would be released in an eruption

Recovery of tritium from lithium-sintered aluminium product (SAP) and lithium-aluminium alloys

International Nuclear Information System (INIS)

Talbot, J.B.; Wiffen, F.W.

1979-01-01

The tritium release rates of irradiated samples of lithium-containing aluminium (Li-Al) and sintered aluminium product (Li-SAP) were investigated to evaluate the potential application of both materials in fusion reactors. The observed release rates followed the pattern expected for bulk diffusion of tritium in a solid. Therefore, diffusion coefficients for tritium in Li-SAP were determined over a temperature range of 383 and 500 0 C and tritium in Li-Al at 450 0 C. At 450 0 C, the diffusion coefficients of tritium in Li-SAP and Li-Al are 2.988 x 10 -10 cm 2 sec -1 and 1.462 x 10 -6 cm 2 sec -1 , respectively. (author)

Characterisation of airborne particulate pollution in the Cu smelter and former mining town of Karabash, South Ural Mountains of Russia.

Science.gov (United States)

Williamson, B J; Udachin, V; Purvis, O W; Spiro, B; Cressey, G; Jones, G C

2004-11-01

Airborne total suspended particulates (TSP), dusts from smelter blast furnace and converter stacks, and filtrates of snow melt waters have been characterised in the Cu smelter and former mining town of Karabash, Russia. TSP was collected at sites up- and downwind of the smelter and large waste and tailings dumps (Oct. 2000 and July 2001). Methods for particle size, mineralogical and elemental determinations have been tested and described, and a new PSD-MicroSOURCE XRD technique developed for the mineralogical analysis of microsamples on filter substrates. TSP in downwind samples has a mean equivalent spherical diameter of 0.5 microm (s.d. = 0.2) and was found to be 100% respirable. The main element of human health/environmental concern, above Russian maximum permitted levels (1 microg m(-3), average over any time period), was Pb which was measured at 16-30 microg m(-3) in downwind samples. Individual particulates mainly consisted of complex mixtures of anglesite (PbSO4), Zn2SnO4 and poorly ordered Zn sulphates. From experimental and theoretical considerations, a high proportion of contained Pb, Zn, Cd and As in this material is considered to be in a readily bioavailable form. Chemical and mineralogical differences between the TSP, stack dusts and snow samples are discussed, as well as the implications for human and regional environmental health.

Thermal formation of corundum from aluminium hydroxides ...

Indian Academy of Sciences (India)

Aluminium hydroxides have been precipitated from various aluminium salts and the differences in their thermal behaviour have been investigated. Pseudoboehmite derived from the nitrate, sulfate and chloride all form -Al2O3 at ∼ 400°C but the formation of -Al2O3 at 1200°C occurs more readily in the material derived ...

Thermal formation of corundum from aluminium hydroxides ...

Indian Academy of Sciences (India)

Abstract. Aluminium hydroxides have been precipitated from various aluminium salts and the differences in their thermal behaviour have been investigated. Pseudoboehmite derived from the nitrate, sulfate and chloride all form γ-Al2O3 at ~ 400°C but the formation of α-Al2O3 at 1200°C occurs more readily in the material ...

Influence of Alkali Treatment on the Surface Area of Aluminium Dross

Directory of Open Access Journals (Sweden)

N. S. Ahmad Zauzi

2016-01-01

Full Text Available Aluminium dross is an industrial waste from aluminium refining industry and classified as toxic substances. However, the disposal of dross as a waste is a burden to aluminium manufacturer industries due to its negative effects to the ecosystem, surface, and ground water. Therefore the purpose of this study is to evaluate the influence of sodium hydroxide (NaOH on the surface area and pore size of aluminium dross. There were 3 stages in the treatment activities, which were leaching, precipitation, and calcination process. The optimum result from this study was the surface area of aluminium dross increases from 10.1 m2/g up to 80.0 m2/g at 40°C, 1% NaOH, and 15-minute reaction time. Thus, aluminium dross has a potential to be converted into other useful material such as catalyst and absorbent. The benefit of this research is that the hazardous industrial waste can be turned into wealth to be used in other applications such as in catalytic activities and absorber in waste water treatment. Further investigation on the physicochemical of aluminium dross with different acid or alkali should be conducted to get deeper understanding on the aluminium dross as a catalyst-type material.

Elastic and plastic properties of iron-aluminium alloys. Special problems raised by the brittleness of alloys of high aluminium content; Proprietes elastiques et plastiques des alliages fer-aluminium. Problemes particuliers poses par la fragilite des alliages a forte teneur en aluminium

Energy Technology Data Exchange (ETDEWEB)

Mouturat, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1966-06-01

The present study embodies the results obtained with iron-aluminium alloys whose composition runs from 0 to nearly 50 atoms per cent aluminium. Conditions of elaboration and transformation have been studied successively, as well as the Young's modulus and the flow stress; the last chapter embodies, a study of the Portevin-le-Chatelier effect in alloys of 40 atoms per cent of aluminium. I) The principal difficulty to clear up consisted in the intergranular brittleness of ordered alloys; this brittleness has been considerably reduced with appropriate conditions of elaboration and transformation. II) The studies upon the Young's modulus are in connection with iron-aluminium alloys; transformation temperatures are well shown up. The formation of covalent bonds on and after 25 atoms per cent show the highest values of the modulus. III) The analysis of variations of the flow stress according to the temperature show some connection with ordered structures, the existence of antiphase domains and the existence of sur-structure dislocations. IV) In the ordered Fe Al domain the kinetics of the Portevin-le-Chatelier effect could be explained by a mechanism of diffusion of vacancies. The role they play has been specified by the influence they exert upon the dislocations; this has led us to the inhomogeneous Rudman order; this inhomogeneous order could explain the shape of the traction curves. (author) [French] Cette etude comporte les resultats obtenus avec des alliages fer-aluminium dont la composition s'etend de 0 a pres de 50 atomes pour cent d'aluminium. Nous avons etudie successivement les conditions d'elaboration et de transformation, le module elastique et la limite elastique; un dernier chapitre est consacre a l'etude du phenomene Portevin-le-Chatelier dans les alliages a 40 atomes pour cent d'aluminium. I) La principale difficulte a resoudre residait dans la fragilite intergranulaire des alliages ordonnes; celle-ci a ete considerablement reduite par des conditions

The binding, transport and fate of aluminium in biological cells.

Science.gov (United States)

Exley, Christopher; Mold, Matthew J

2015-04-01

Aluminium is the most abundant metal in the Earth's crust and yet, paradoxically, it has no known biological function. Aluminium is biochemically reactive, it is simply that it is not required for any essential process in extant biota. There is evidence neither of element-specific nor evolutionarily conserved aluminium biochemistry. This means that there are no ligands or chaperones which are specific to its transport, there are no transporters or channels to selectively facilitate its passage across membranes, there are no intracellular storage proteins to aid its cellular homeostasis and there are no pathways which evolved to enable the metabolism and excretion of aluminium. Of course, aluminium is found in every compartment of every cell of every organism, from virus through to Man. Herein we have investigated each of the 'silent' pathways and metabolic events which together constitute a form of aluminium homeostasis in biota, identifying and evaluating as far as is possible what is known and, equally importantly, what is unknown about its uptake, transport, storage and excretion. Copyright © 2014 Elsevier GmbH. All rights reserved.

Wear and chemistry of zirconium-silicate, aluminium-silicate and zirconium-aluminium-silicate glasses in alkaline medium

International Nuclear Information System (INIS)

Rouse, C.G.; Lemos Guenaga, C.M. de

1984-01-01

A study of the chemical durability, in alkaline solutions, of zirconium silicate, aluminium silicate, zirconium/aluminium silicate glasses as a function of glass composition is carried out. The glasses were tested using standard DIN-52322 method, where the glass samples are prepared in small polished pieces and attacked for 3 hours in a 800 ml solution of 1N (NaOH + NA 2 CO 3 ) at 97 0 C. The results show that the presence of ZrO 2 in the glass composition increases its chemical durability to alkaline attack. Glasses of the aluminium/zirconium silicate series were melted with and without TiO 2 . It was shown experimentally that for this series of glasses, the presence of both TiO 2 and ZrO 2 gave better chemical durability results. However, the best overall results were obtained from the simpler zirconium silicate glasses, where it was possible to make glasses with higher values of ZrO 2 . (Author) [pt

Aluminium effect on the physical properties of titanium

International Nuclear Information System (INIS)

Nazimov, O.P.; Il'in, A.A.; Zvonova, L.N.

1977-01-01

The effect of aluminium on the physical properties of titanium was investigated. Within the framework of the configuration model of matter it is shown that a change in physical properties with an aluminium content of up to 7.5 wt.% in alloys depends on the phase composition and electron structure. In interacting with titanium, aluminium exhibits acceptor properties, causing d→s electron transitions. The electrons which have shifted to the s-state are partly collectivized and partly localized into quasistable sp 3 configurations, with the resulting increase of the interatomic forces. An intensification of d→s transitions in alloying of titanium with aluminium stabilizes the α-phase. Predominance of d 1 configurations in the intermediate spectrum in the region of the α-solution increases the ratio of the axes of the HCP lattice and determines the electron type of conduction of alloys of the Ti-Al system

Aluminium and Aroma Compound Concentration in Beer During Storage at Different Temperatures

Directory of Open Access Journals (Sweden)

Marija Soldo Gjeldum

2006-01-01

Full Text Available Problem of aluminium in beer has been elaborated in several papers over the last decade. However, the effect of aluminium on organoleptic properties of beer has been observed in few papers where it has been stated that aluminium gives beer a »metallic« and bitter flavour without any observations on particular aroma compound changes. Also, the number of reports on precise changes of aroma components throughout different storage conditions is surprisingly scarce. In order to investigate the changes of aluminium concentration along with aroma compound changes, graphite furnace-atomic absorption spectrophotometry (GF-AAS with Zeeman background correction and gas chromatography with static headspace sampler (GC-HSS were used in this work. Analyses were conducted periodically throughout seven months of storage on three different brands of beer from name breweries. Samples were taken before and after filling in aluminium cans. One part of samples was stored in a refrigerator (4 °C and the other in a thermostatic chamber (22 °C. The effects of beer brand and storage conditions on aluminium concentration and level of aroma compounds were measured. To prove the effect of aluminium concentration on the changes of aroma compounds, the adequate level of aluminium sulphate was added to bottled beer samples stored at 28 °C. Although different beer types showed significantly different aluminium concentration, it could be the result of other factors (different batches of identical beer type showed significantly different aluminium concentration as well. Samples that were stored in the refrigerator were protected from aluminium migration from the can to the beer and showed increased aroma stability. Level of aroma constituents of analyzed beer brands was significantly different. Elevated aluminium concentration did not have any noticeable effect on the level of aroma compounds in beer samples stored at 28 °C.

Experimental Realisation of Elusive Multiple-bonded Aluminium Compounds: A New Horizon in the Aluminium Chemistry.

Science.gov (United States)

Inoue, Shigeyoshi; Bag, Prasenjit; Weetman, Catherine

2018-05-23

Synthesis and isolation of stable main group compounds featuring multiple bonds has been of keen interest for the last several decades. Multiply bonded complexes were obtained using sterically demanding substituents that provide kinetic and thermodynamic stability. Many of these compounds have unusual structural and electronic properties that challenges the classical concept of covalent multiple bonding. In contrast, analogous aluminium compounds are scarce in spite of its high natural abundance. The parent dialumene (Al2H2) has been calculated to be extremely weak, thus making Al multiple bonds a challenging synthetic target. This review provides an overview of these recent advances in the cutting edge synthetic approaches used to obtain aluminium homo- and heterodiatomic multiply bonded complexes. Additionally, the reactivity of these novel compounds towards various small molecules and reagents will be discussed herein. This review provides an overview on the current progress in aluminium multiple bond chemistry and the careful ligand design required to stabilise these reactive species. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Sintered aluminium powders

International Nuclear Information System (INIS)

Stepanova, M.G.; Matveev, B.I.

1974-01-01

The mechanical and physical properties of aluminium powder alloys and the various methods employed to produce them are considered. Data are given on the hardening of the alloys SAP and SPAK-4, as well as the powder-alloy system Al-Cr-Zr. (L.M.)

Silane based coating of aluminium mold

DEFF Research Database (Denmark)

2013-01-01

having at least one closed cavity is provided, at least one surface of the at least one cavity being an aluminium surface coated with a silane based coating layer. The silane based anti-stiction coating improves the anti-stiction properties of the mold which may allow for molding and demolding...... of structures which would otherwise be difficult to mold. The resistance of the coated aluminium mold is significantly improved by applying a silane-based coating layer....

Aluminium hydroxide-induced granulomas in pigs

DEFF Research Database (Denmark)

Valtulini, S; Macchi, C; Ballanti, P

2005-01-01

The effect of intramuscular injection of 40 mg/2 ml aluminium hydroxide in the neck of pigs was examined in a number of ways. The investigation followed repeated slaughterhouse reports, according to which 64.8% of pigs from one particular farm were found at slaughter to have one or more nodules...... in the muscles of the neck (group slaughtered). The pigs had been injected with a vaccine containing 40 mg/2 ml dose of aluminium hydroxide as adjuvant. Research consisted of two phases: first, an epidemiological study was carried out, aimed at determining the risk factors for the granulomas. The results...... and adjuvant) to pigs inoculated twice with apyrogenic bi-distilled water (group water) and to pigs inoculated once with the adjuvant and once with apyrogenic bi-distilled water (group adjuvant/water). Both studies agreed in their conclusions, which indicate that the high amount of aluminium hydroxide...

Finite size melting of spherical solid-liquid aluminium interfaces

DEFF Research Database (Denmark)

Chang, J.; Johnson, Erik; Sakai, T.

2009-01-01

We have investigated the melting of nano-sized cone shaped aluminium needles coated with amorphous carbon using transmission electron microscopy. The interface between solid and liquid aluminium was found to have spherical topology. For needles with fixed apex angle, the depressed melting tempera...... to the conclusion that the depressed melting temperature is not controlled solely by the inverse radius 1/R. Instead, we found a direct relation between the depressed melting temperature and the ratio between the solid-liquid interface area and the molten volume.......We have investigated the melting of nano-sized cone shaped aluminium needles coated with amorphous carbon using transmission electron microscopy. The interface between solid and liquid aluminium was found to have spherical topology. For needles with fixed apex angle, the depressed melting...

Structural perturbation of diphtheria toxoid upon adsorption to aluminium hydroxide adjuvant

NARCIS (Netherlands)

Regnier, M.; Metz, B.; Tilstra, W.; Hendriksen, C.; Jiskoot, W.; Norde, W.; Kersten, G.

2012-01-01

Aluminium-containing adjuvants are often used to enhance the potency of vaccines. In the present work we studied whether adsorption of diphtheria toxoid to colloidal aluminium hydroxide induces conformational changes of the antigen. Diphtheria toxoid has a high affinity for the aluminium hydroxide

Disruption of an Alumina Layer During Sintering of Aluminium in Nitrogen

Directory of Open Access Journals (Sweden)

Pieczonka T.

2017-06-01

Full Text Available Aluminium oxide layer on aluminium particles cannot be avoided. However, to make the metal-metal contacts possible, this sintering barrier has to be overcome in some way, necessarily to form sintering necks and their development. It is postulated that the disruption of alumina layer under sintering conditions may originate physically and chemically. Additionally, to sinter successfully non alloyed aluminium powder in nitrogen, the operation of both types mechanism is required. It is to be noted that metallic aluminium surface has to be available to initiate reactions between aluminium and the sintering atmosphere, i.e. mechanical disruption of alumina film precedes the chemical reactions, and only then chemically induced mechanisms may develop. Dilatometry, gravimetric and differential thermal analyses, and microstructure investigations were used to study the sintering response of aluminium at 620°C in nitrogen, which is the only sintering atmosphere producing shrinkage.

Recycled Aluminium Cans/Eggshell Composites: Evaluation of Mechanical and Wear Resistance Properties

Directory of Open Access Journals (Sweden)

J.O. Agunsoye

2015-03-01

Full Text Available Aluminium based metal matrix composites have been produced from recycled aluminium cans and 150µm sized eggshell particles using a stir cast process. The mechanical properties of the control and aluminium can/eggshell composites produced have been investigated. The microstructures of the aluminium can/eggshell composites were examined with the aids of Scanning Electron Microscope (SEM after the sample surfaces have been carefully prepared and etched with aqueous solution of 0.5 cm3 nitric acid. Micrographs revealed that there was a homogenous distribution of eggshell particles within the aluminium can matrix. An indication of effective stirring action during the melting process. The wear resistance was also investigated under different applied loads (6 to 14 N on an abrasive surface emery paper of grade 220. The results revealed an increase in Young’s modulus of elasticity and yield stress from 1,206.45 and 50.23 Mpa respectively of the cast aluminium can with 0 % eggshell particle to the maximum of 3,258.87and 73.2 MPa of aluminium can/12 % eggshell composites. The hardness values increased from 66.23 to 75.13 VN. There was a gradual increase in wear rate of the tested samples as the applied load increased. However, the wear resistance of the aluminium can/6 % eggshell and aluminium can/12 % eggshell composites increased significantly. Hence, recycling of aluminium cans and eggshells can be harnessed into development of useful engineering metal matrix composite materials.

Surface roughness when diamond turning RSA 905 optical aluminium

Science.gov (United States)

Otieno, T.; Abou-El-Hossein, K.; Hsu, W. Y.; Cheng, Y. C.; Mkoko, Z.

2015-08-01

Ultra-high precision machining is used intensively in the photonics industry for the production of various optical components. Aluminium alloys have proven to be advantageous and are most commonly used over other materials to make various optical components. Recently, the increasing demand from optical systems for optical aluminium with consistent material properties has led to the development of newly modified grades of aluminium alloys produced by rapid solidification in the foundry process. These new aluminium grades are characterised by their finer microstructures and refined mechanical and physical properties. However the machining database of these new optical aluminium grades is limited and more research is still required to investigate their machinability performance when they are diamond turned in ultrahigh precision manufacturing environment. This work investigates the machinability of rapidly solidified aluminium RSA 905 by varying a number of diamond-turning cutting parameters and measuring the surface roughness over a cutting distance of 4 km. The machining parameters varied in this study were the cutting speed, feed rate and depth of cut. The results showed a common trend of decrease in surface roughness with increasing cutting distance. The lowest surface roughness Ra result obtained after 4 km in this study was 3.2 nm. This roughness values was achieved using a cutting speed of 1750 rpm, feed rate of 5 mm/min and depth of cut equal to 25 μm.

In vivo monitoring of skeletal aluminium burden in patients with renal failure

International Nuclear Information System (INIS)

Ellis, K.J.; Kelleher, S.; Raciti, A.; Savory, J.; Wills, M.

1988-01-01

In vivo neutron activation analysis was used to examine the total body and partial body (hand) aluminium levels in patients with end-stage renal failure. Patients maintained on chronic hemodialysis had higher mean body burdens of aluminium than did those clinically managed without dialysis. Approximately 70% of the patients examined indicated elevated levels of body or skeletal aluminium. A significant correlation was observed between the in vivo aluminium/calcium ratio obtained for the hand measurement and the increase in serum aluminium levels following a disferroxamine infusion test. The direct in vivo monitoring of hand Al/Ca values in patients may provide an alternate choice to bone biopsy for the detection of aluminium intoxication. (author) 15 refs.; 5 figs.; 2 tabs

Dietary exposure to aluminium in the popular Chinese fried bread youtiao.

Science.gov (United States)

Li, Ge; Zhao, Xue; Wu, Shimin; Hua, Hongying; Wang, Qiang; Zhang, Zhiheng

2017-06-01

Youtiao is a typical, traditional and widely consumed fried food in China. Fermentation of youtiao involves the use of aluminium potassium sulphate (alum). There are health concerns related to the levels of aluminium in food; therefore, we aimed to determine the aluminium concentrations of youtiao from various locations, and to estimate the dietary exposure by different age groups in southern and northern China. The aluminium content of youtiao samples varied considerably (range = 4.46-852.69 mg kg -1 ). Both the mean and median aluminium contents of youtiao exceeded 100 mg kg -1 , which is the China National Standard (GB) 2760-2014 National Food Safety for Standards for food additives. However, the median and 97.5th percentile of weekly dietary exposure to aluminium from youtiao, estimated using Monte Carlo simulation, did not exceed the provisional tolerable weekly intake (PTWI) set by the joint FAO/WHO Expert Committee on Food Additives (JECFA) for children, adolescents, adults and seniors. The weekly dietary exposure to aluminium would exceed the PTWI if children, adolescents, adults and seniors consumed 134.47, 260.98, 327.10 or 320.41 g of youtiao per week, respectively.

Silicon Alloying On Aluminium Based Alloy Surface

International Nuclear Information System (INIS)

Suryanto

2002-01-01

Silicon alloying on surface of aluminium based alloy was carried out using electron beam. This is performed in order to enhance tribological properties of the alloy. Silicon is considered most important alloying element in aluminium alloy, particularly for tribological components. Prior to silicon alloying. aluminium substrate were painted with binder and silicon powder and dried in a furnace. Silicon alloying were carried out in a vacuum chamber. The Silicon alloyed materials were assessed using some techniques. The results show that silicon alloying formed a composite metal-non metal system in which silicon particles are dispersed in the alloyed layer. Silicon content in the alloyed layer is about 40% while in other place is only 10.5 %. The hardness of layer changes significantly. The wear properties of the alloying alloys increase. Silicon surface alloying also reduced the coefficient of friction for sliding against a hardened steel counter face, which could otherwise be higher because of the strong adhesion of aluminium to steel. The hardness of the silicon surface alloyed material dropped when it underwent a heating cycle similar to the ion coating process. Hence, silicon alloying is not a suitable choice for use as an intermediate layer for duplex treatment

Dietary exposure to aluminium of urban residents from cities in South China.

Science.gov (United States)

Jiang, Qi; Wang, Jing; Li, Min; Liang, Xuxia; Dai, Guangwei; Hu, Zhikun; Wen, Jian; Huang, Qiong; Zhang, Yonghui

2013-01-01

A dietary survey was conducted over three consecutive days by using 24-hour dietary recall in the Pearl River Delta of South China to investigate the dietary consumption status. A total of 1702 food samples, 22 food groups, were collected, and aluminium concentrations of foods were determined by using ICP-MS. Weekly dietary exposure to aluminium of the average urban residents of South China was estimated to be 1.5 mg kg⁻¹ body weight, which amounted to 76% of the provisional tolerable weekly intake. Wheat-made products (53.5%) contributed most to the dietary exposure, followed by vegetables (12.2%). The high-level consumers' weekly exposure to aluminium was 11.1 mg kg⁻¹ body weight, which amounted to 407% of the provisional tolerable weekly intake. The results indicated that the general urban residents in South China might be safe from aluminium exposure, but the high-level consumers might be at some risk of aluminium exposure. The foods contributing to aluminium exposure were processed food with aluminium-containing food additives. It is necessary to take effective measures to control the overuse of aluminium-containing food additives.

Usage of neural network to predict aluminium oxide layer thickness.

Science.gov (United States)

Michal, Peter; Vagaská, Alena; Gombár, Miroslav; Kmec, Ján; Spišák, Emil; Kučerka, Daniel

2015-01-01

This paper shows an influence of chemical composition of used electrolyte, such as amount of sulphuric acid in electrolyte, amount of aluminium cations in electrolyte and amount of oxalic acid in electrolyte, and operating parameters of process of anodic oxidation of aluminium such as the temperature of electrolyte, anodizing time, and voltage applied during anodizing process. The paper shows the influence of those parameters on the resulting thickness of aluminium oxide layer. The impact of these variables is shown by using central composite design of experiment for six factors (amount of sulphuric acid, amount of oxalic acid, amount of aluminium cations, electrolyte temperature, anodizing time, and applied voltage) and by usage of the cubic neural unit with Levenberg-Marquardt algorithm during the results evaluation. The paper also deals with current densities of 1 A · dm(-2) and 3 A · dm(-2) for creating aluminium oxide layer.

Usage of Neural Network to Predict Aluminium Oxide Layer Thickness

Directory of Open Access Journals (Sweden)

Peter Michal

2015-01-01

Full Text Available This paper shows an influence of chemical composition of used electrolyte, such as amount of sulphuric acid in electrolyte, amount of aluminium cations in electrolyte and amount of oxalic acid in electrolyte, and operating parameters of process of anodic oxidation of aluminium such as the temperature of electrolyte, anodizing time, and voltage applied during anodizing process. The paper shows the influence of those parameters on the resulting thickness of aluminium oxide layer. The impact of these variables is shown by using central composite design of experiment for six factors (amount of sulphuric acid, amount of oxalic acid, amount of aluminium cations, electrolyte temperature, anodizing time, and applied voltage and by usage of the cubic neural unit with Levenberg-Marquardt algorithm during the results evaluation. The paper also deals with current densities of 1 A·dm−2 and 3 A·dm−2 for creating aluminium oxide layer.

Stability and leaching of cobalt smelter fly ash

DEFF Research Database (Denmark)

Vítková, Martina; Hyks, Jiri; Ettler, Vojtěch

2013-01-01

The leaching behaviour of fly ash from a Co smelter situated in the Zambian Copperbelt was studied as a function of pH (5–12) using the pH-static leaching test (CEN/TS 14997). Various experimental time intervals (48h and 168h) were evaluated. The leaching results were combined with the ORCHESTRA...... modelling framework and a detailed mineralogical investigation was performed on the original FA and leached solid residues. The largest amounts of Co, Cu, Pb and Zn were leached at pH 5, generally with the lowest concentrations between pH 9 and 11 and slightly increased concentrations at pH 12. For most...... detected using SEM/EDS and/or TEM/EDS. The leaching of metals was mainly attributed to the dissolution of metallic particles. Partial dissolution of silicate and glass fractions was assumed to significantly influence the release of Ca, Mg, Fe, K, Al and Si as well as Cu, Co and Zn. The formation of illite...

Elastic and plastic properties of iron-aluminium alloys. Special problems raised by the brittleness of alloys of high aluminium content; Proprietes elastiques et plastiques des alliages fer-aluminium. Problemes particuliers poses par la fragilite des alliages a forte teneur en aluminium

Energy Technology Data Exchange (ETDEWEB)

Mouturat, P. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1966-06-01

The present study embodies the results obtained with iron-aluminium alloys whose composition runs from 0 to nearly 50 atoms per cent aluminium. Conditions of elaboration and transformation have been studied successively, as well as the Young's modulus and the flow stress; the last chapter embodies, a study of the Portevin-le-Chatelier effect in alloys of 40 atoms per cent of aluminium. I) The principal difficulty to clear up consisted in the intergranular brittleness of ordered alloys; this brittleness has been considerably reduced with appropriate conditions of elaboration and transformation. II) The studies upon the Young's modulus are in connection with iron-aluminium alloys; transformation temperatures are well shown up. The formation of covalent bonds on and after 25 atoms per cent show the highest values of the modulus. III) The analysis of variations of the flow stress according to the temperature show some connection with ordered structures, the existence of antiphase domains and the existence of sur-structure dislocations. IV) In the ordered Fe Al domain the kinetics of the Portevin-le-Chatelier effect could be explained by a mechanism of diffusion of vacancies. The role they play has been specified by the influence they exert upon the dislocations; this has led us to the inhomogeneous Rudman order; this inhomogeneous order could explain the shape of the traction curves. (author) [French] Cette etude comporte les resultats obtenus avec des alliages fer-aluminium dont la composition s'etend de 0 a pres de 50 atomes pour cent d'aluminium. Nous avons etudie successivement les conditions d'elaboration et de transformation, le module elastique et la limite elastique; un dernier chapitre est consacre a l'etude du phenomene Portevin-le-Chatelier dans les alliages a 40 atomes pour cent d'aluminium. I) La principale difficulte a resoudre residait dans la fragilite intergranulaire des alliages ordonnes; celle-ci a ete

The aluminium content of breast tissue taken from women with breast cancer.

Science.gov (United States)

House, Emily; Polwart, Anthony; Darbre, Philippa; Barr, Lester; Metaxas, George; Exley, Christopher

2013-10-01

The aetiology of breast cancer is multifactorial. While there are known genetic predispositions to the disease it is probable that environmental factors are also involved. Recent research has demonstrated a regionally specific distribution of aluminium in breast tissue mastectomies while other work has suggested mechanisms whereby breast tissue aluminium might contribute towards the aetiology of breast cancer. We have looked to develop microwave digestion combined with a new form of graphite furnace atomic absorption spectrometry as a precise, accurate and reproducible method for the measurement of aluminium in breast tissue biopsies. We have used this method to test the thesis that there is a regional distribution of aluminium across the breast in women with breast cancer. Microwave digestion of whole breast tissue samples resulted in clear homogenous digests perfectly suitable for the determination of aluminium by graphite furnace atomic absorption spectrometry. The instrument detection limit for the method was 0.48 μg/L. Method blanks were used to estimate background levels of contamination of 14.80 μg/L. The mean concentration of aluminium across all tissues was 0.39 μg Al/g tissue dry wt. There were no statistically significant regionally specific differences in the content of aluminium. We have developed a robust method for the precise and accurate measurement of aluminium in human breast tissue. There are very few such data currently available in the scientific literature and they will add substantially to our understanding of any putative role of aluminium in breast cancer. While we did not observe any statistically significant differences in aluminium content across the breast it has to be emphasised that herein we measured whole breast tissue and not defatted tissue where such a distribution was previously noted. We are very confident that the method developed herein could now be used to provide accurate and reproducible data on the aluminium content

Probing the distribution and contamination levels of 10 trace metal/metalloids in soils near a Pb/Zn smelter in Middle China.

Science.gov (United States)

Li, Zhonggen; Feng, Xinbin; Bi, Xiangyang; Li, Guanghui; Lin, Yan; Sun, Guangyi

2014-03-01

The horizontal and vertical distribution patterns and contamination status of ten trace metal/metalloids (Ag, Bi, Co, Cr, Ge, In, Ni, Sb, Sn, Tl) in soils around one of the largest Chinese Pb-Zn smelter in Zhuzhou City, Central China, were revealed. Different soil samples were collected from 11 areas, including ten agricultural areas and one city park area, with a total of 83 surface soil samples and six soil cores obtained. Trace metal/metalloids were determined by inductively coupled plasma-mass spectrometry after digestion by an acid mixture of HF and HNO3. The results showed that Ag, Bi, In, Sb, Sn, and Tl contents decreased both with the distance to the Pb-Zn smelter as well as the soil depth, hinting that these elements were mainly originated from the Pb-Zn smelting operations and were introduced into soils through atmospheric deposition. Soil Ge was influenced by the smelter at a less extent, while the distributions of Co, Cr, and Ni were roughly even among most sampling sites and soil depths, suggesting that they were primarily derived from natural sources. The contamination status, as revealed by the geo-accumulation index (I geo), indicated that In and Ag were the most enriched elements, followed by Sb, Bi, and Sn. In general, Cr, Tl, Co, Ni, and Ge were of an uncontaminated status.

Potentiometric titration curves of aluminium salt solutions and its ...

African Journals Online (AJOL)

Potentiometric titration curves of aluminium salt solutions and its species conversion ... of aluminium salt solutions under the moderate slow rate of base injection. ... silicate radical, and organic acid radical on the titration curves and its critical ...

Bioaccumulation of Aluminium in Hydromacrophytes in Polish Coastal Lakes

Directory of Open Access Journals (Sweden)

Senze Magdalena

2015-03-01

Full Text Available The research on aluminium content was conducted in water and on aquatic flora of Polish lakes in the central part of the coast. The study included the lakes Sarbsko, Choczewskie, Bia.e, K.odno, D.brze and Salino investigated in the summer of 2013. The examined lakes belong mainly to the direct basin of the Baltic Sea. Samples of aquatic plants and lake waters were collected. In the water samples pH and electrolytic conductivity were measured. The aluminium content was determined both in water and aquatic plants. Submerged hydromacrophyte studies included Myriophyllum alterniflorum L., Potamogeton perfoliatus L. and Ceratophyllum demersum L. Emergent hydromacrophyte studies included Phragmites australis (Cav. Trin. ex Steud., Juncus bulbosus L., Iris pseudacorus L., Eleocharis palustris (L. Roem. % Schult., Phalaris arundinacea L., Carex riparia Curt., Mentha aquatic L., Stratiotes aloides L., Alisma plantago-aquatica L., Glyceria maxima (Hartman Holmb., Sagittaria sagittifolia L., Scirpus lacustris L. and Typha angustifolia L. The purpose of this investigation was the determination of the aluminium content in submerged and emergent hydromacrophytes and also the definition of their bioaccumulative abilities. The average concentration of aluminium in water was 2.68 fęg Al dm.3. The average content of aluminium in plants was 2.8015 mg Al kg.1. The bioaccumulation factor ranged from BCF=19.74 to BCF=16619. On the basis of the analysis of the aluminium content in water and aquatic plants results show that both water and plants were characterized by a moderate level of aluminium. The recorded concentrations indicate a mid-range value and are much lower than those which are quoted for a variety of surface waters in various parts of the world.

Lake restoration with aluminium, bentonite and Phoslock: the effect on sediment stability and light attenuation

DEFF Research Database (Denmark)

Egemose, Sara; Reitzel, Kasper; Flindt, Mogens

treatments on aluminium mobility, sediment stability or light climate. A laboratory flume experiment including three shallow Danish lakes was conducted. We measured the effects of aluminium, Phoslock (a commercial product), bentonite, and a combination of bentonite/aluminium. Each treatment caused a varying...... consolidation of the sediment. The largest consolidation occurred using Phoslock- and bentonite-addition followed by bentonite/aluminium-addition, whereas aluminium alone had no effect. Sediment stability thresholds were measured before and after addition. Especially Phoslock, but also bentonite and bentonite....../aluminium increased sediment erosion threshold, with respectively 200%, 43% and 57%. Aluminium, bentonite/aluminium, and Phoslock improved the light conditions in the water phase, with respectively 60%, 57% and 50%, whereas bentonite created higher turbidity. Conclusively aluminium improved the light conditions...

Anodization of Aluminium using a fast two-step process

Indian Academy of Sciences (India)

283.6 eV. Keywords. Anodization; phosphoric acid; anodization time; anodized aluminium oxide; aluminium. ... of anodization.5–7 The AAO layer has a large band gap, good ..... transmittance increases as the anodised membrane is heated to ...

Serum aluminium levels in glue-sniffer adolescent and in glue containers.

Science.gov (United States)

Akay, Cemal; Kalman, Süleyman; Dündaröz, Ruşen; Sayal, Ahmet; Aydin, Ahmet; Ozkan, Yalçin; Gül, Hüsamettin

2008-05-01

Glue sniffing is a serious medical problem among teenagers. Various chemical substances such as toluene and benzene containing glues have been reported to be toxic. It has been demonstrated that some toxic metals such as lead are elevated in the blood of solvent-addicted patients. Whereas aluminium is an element that has toxic effects on neurological, hematopoetic system and bone metabolism. We want to determine the serum levels of aluminium in glue-sniffer adolescents in comparison with healthy subjects. In addition, we compared aluminium levels of different commercial glue preparations (i.e. metal and plastic containers), to determine which type of container is better for less aluminium toxicity. We measured serum levels of aluminium in 37 glue-sniffer and 37 healthy subjects using atomic absorption spectrophotometry. The average duration of glue-sniffer was 3.8 +/- 0.8 years. We also measured aluminium levels of 10 commercial glue preparations that seven of them with metal and three with plastic containers. We found that serum levels of aluminium were 63.29 +/- 13.20 ng/ml and 36.7 +/- 8.60 ng/ml in glue-sniffer and in control subjects, respectively (P sniffers, it may be a good step to market of glue preparations in plastic instead of metal containers.

Derivation of a water quality guideline for aluminium in marine waters.

Science.gov (United States)

Golding, Lisa A; Angel, Brad M; Batley, Graeme E; Apte, Simon C; Krassoi, Rick; Doyle, Chris J

2015-01-01

Metal risk assessment of industrialized harbors and coastal marine waters requires the application of robust water quality guidelines to determine the likelihood of biological impacts. Currently there is no such guideline available for aluminium in marine waters. A water quality guideline of 24 µg total Al/L has been developed for aluminium in marine waters based on chronic 10% inhibition or effect concentrations (IC10 or EC10) and no-observed-effect concentrations (NOECs) from 11 species (2 literature values and 9 species tested including temperate and tropical species) representing 6 taxonomic groups. The 3 most sensitive species tested were a diatom Ceratoneis closterium (formerly Nitzschia closterium; IC10 = 18 µg Al/L, 72-h growth rate inhibition) aluminium forms of aluminate (Al(OH4 (-) ) and aluminium hydroxide (Al(OH)3 (0) ) although both dissolved, and particulate aluminium contributed to toxicity in the diatom Minutocellus polymorphus and green alga Dunaliella tertiolecta. In contrast, aluminium toxicity to the green flagellate alga Tetraselmis sp. was the result of particulate aluminium only. Four species, a brown macroalga (Hormosira banksii), sea urchin embryo (Heliocidaris tuberculata), and 2 juvenile fish species (Lates calcarifer and Acanthochromis polyacanthus), were not adversely affected at the highest test concentration used. © 2014 SETAC.

Heavy metal contamination of topsoils around a lead and zinc smelter in the Republic of Macedonia

International Nuclear Information System (INIS)

Stafilov, Trajce; Sajn, Robert; Pancevski, Zlatko; Boev, Blazo; Frontasyeva, Marina V.; Strelkova, Lyudmila P.

2010-01-01

The results of a first systematic study of spatial distribution of different elements in surface soil over the Veles region (50 km 2 ) known for its lead and zinc industrial activity in the recent past are reported. A total of 201 soil samples were collected according to a dense net in urban area and less dense net in rural area. The total of 42 elements were analyzed by epithermal neutron activation analysis (ENAA) and by atomic absorption spectrometry (AAS). The content of elements such as As, Au, Cd, Cu, Hg, In, Pb, Sb, Se, Zn in soil samples around the lead and zinc smelter and in the adjacent part of the town of Veles has appeared to be much higher than in those collected in the surrounding areas due to the pollution from the plant. Thus, the content of Cd (three times); Pb and Zn (two times) is even higher than the corresponding intervention (critical) values according to the Dutch standards. The results obtained by two complementary analytical techniques, AAS and ENAA, are discussed in terms of multivariate statistics. GIS technology was applied to depict the areas most affected by contamination from the lead and zinc smelter.

The Impact of a Nickel-Copper Smelter on Concentrations of Toxic Elements in Local Wild Food from the Norwegian, Finnish, and Russian Border Regions.

Science.gov (United States)

Hansen, Martine D; Nøst, Therese H; Heimstad, Eldbjørg S; Evenset, Anita; Dudarev, Alexey A; Rautio, Arja; Myllynen, Päivi; Dushkina, Eugenia V; Jagodic, Marta; Christensen, Guttorm N; Anda, Erik E; Brustad, Magritt; Sandanger, Torkjel M

2017-06-28

Toxic elements emitted from the Pechenganickel complex on the Kola Peninsula have caused concern about potential effects on local wild food in the border regions between Norway, Finland and Russia. The aim of this study was to assess Ni, Cu, Co, As, Pb, Cd, and Hg concentrations in local wild foods from these border regions. During 2013-2014, we collected samples of different berry, mushroom, fish, and game species from sites at varying distances from the Ni-Cu smelter in all three border regions. Our results indicate that the Ni-Cu smelter is the main source of Ni, Co, and As in local wild foods, whereas the sources of Pb and Cd are more complex. We observed no consistent trends for Cu, one of the main toxic elements emitted by the Ni-Cu smelter; nor did we find any trend for Hg in wild food. Concentrations of all investigated toxic elements were highest in mushrooms, except for Hg, which was highest in fish. EU maximum levels of Pb, Cd, and Hg were exceeded in some samples, but most had levels considered safe for human consumption. No international thresholds exist for the other elements under study.

Deposition of aluminium nanoparticles using dense plasma focus device

International Nuclear Information System (INIS)

Devi, Naorem Bilasini; Srivastava, M P; Roy, Savita

2010-01-01

Plasma route to nanofabrication has drawn much attention recently. The dense plasma focus (DPF) device is used for depositing aluminium nanoparticles on n-type Si (111) wafer. The plasma chamber is filled with argon gas and evacuated at a pressure of 80 Pa. The substrate is placed at distances 4.0 cm, 5.0 cm and 6.0 cm from the top of the central anode. The aluminium is deposited on Si wafer at room temperature with two focused DPF shots. The deposits on the substrate are examined for their morphological properties using atomic force microscopy (AFM). The AFM images have shown the formation of aluminium nanoparticles. From the AFM images, it is found that the size of aluminium nanoparticles increases with increase in distance between the top of anode and the substrate for same number of DPF shots.

Corrosion issues of powder coated AA6060 aluminium profiles

DEFF Research Database (Denmark)

Din, Rameez Ud; Valgarðsson, Smári; Jellesen, Morten Stendahl

2015-01-01

In this study detailed microstructural investigation of the reason for unexpected corrosion of powder coated aluminium alloy AA6060 windows profiles has been performed. The results from this study reveals that the failure of the window profiles was originated from the surface defects present...... on the extruded AA6060 aluminium profile after metallurgical process prior to powder coating. Surface defects are produced due to intermetallic particles in the alloy, which disturb the flow during the extrusion process. The corrosion mechanism leading to the failure of the powder coated AA6060 aluminium profiles...

Aluminium tolerance in rice is antagonistic with nitrate preference and synergistic with ammonium preference.

Science.gov (United States)

Zhao, Xue Qiang; Guo, Shi Wei; Shinmachi, Fumie; Sunairi, Michio; Noguchi, Akira; Hasegawa, Isao; Shen, Ren Fang

2013-01-01

Acidic soils are dominated chemically by more ammonium and more available, so more potentially toxic, aluminium compared with neutral to calcareous soils, which are characterized by more nitrate and less available, so less toxic, aluminium. However, it is not known whether aluminium tolerance and nitrogen source preference are linked in plants. This question was investigated by comparing the responses of 30 rice (Oryza sativa) varieties (15 subsp. japonica cultivars and 15 subsp. indica cultivars) to aluminium, various ammonium/nitrate ratios and their combinations under acidic solution conditions. indica rice plants were generally found to be aluminium-sensitive and nitrate-preferring, while japonica cultivars were aluminium-tolerant and relatively ammonium-preferring. Aluminium tolerance of different rice varieties was significantly negatively correlated with their nitrate preference. Furthermore, aluminium enhanced ammonium-fed rice growth but inhibited nitrate-fed rice growth. The results suggest that aluminium tolerance in rice is antagonistic with nitrate preference and synergistic with ammonium preference under acidic solution conditions. A schematic diagram summarizing the interactions of aluminium and nitrogen in soil-plant ecosystems is presented and provides a new basis for the integrated management of acidic soils.

Synthesis, properties, and assimilation methods of aluminium hydride

International Nuclear Information System (INIS)

Mirsaidov, U.M.

2013-01-01

We have discovered a new source of aluminium hydride-conversion of tetrahydrofurane under influence of halogenous alkyls. We have proposed the chlorbenzene method of synthesis of AlH 3 , which excludes adhesion and ensure high quality of the product with respect to its purity, thermal stability, habits of crystals (round shape), and granulometric composition. We determined capability of benzyl chloride to fix AlH 4 -groups by the way of complexes formation. This allows increasing efficient concentration of AlH 3 solutions and their productivity. We have carried out 'direct' crystallization of aluminium hydride in one stage using interaction of binary metal hydride with aluminium chloride in the medium of ether-toluene at 60-100 d ig C a nd using solvent distillation. In the reaction of Li H with AlCl 3 , we achieved output of pure crystal AlH 3 of hexagonal modification, which was close to quantitative. We have discovered the assimilation methods of aluminium hydride in carrying out of solid-phase chemical reactions. (author)

Indentation of aluminium foam at low velocity

Directory of Open Access Journals (Sweden)

Shi Xiaopeng

2015-01-01

Full Text Available The indentation behaviour of aluminium foams at low velocity (10 m/s ∼ 30 m/s was investigated both in experiments and numerical simulation in this paper. A flat-ended indenter was used and the force-displacement history was recorded. The Split Hopkinson Pressure bar was used to obtain the indentation velocity and forces in the dynamic experiments. Because of the low strength of the aluminium foam, PMMA bar was used, and the experimental data were corrected using Bacon's method. The energy absorption characteristics varying with impact velocity were then obtained. It was found that the energy absorption ability of aluminium foam gradually increases in the quasi-static regime and shows a significant increase at ∼10 m/s velocity. Numerical simulation was also conducted to investigate this process. A 3D Voronoi model was used and models with different relative densities were investigated as well as those with different failure strain. The indentation energy increases with both the relative density and failure strain. The analysis of the FE model implies that the significant change in energy absorption ability of aluminium foam in indentation at ∼10 m/s velocity may be caused by plastic wave effect.

Improvement of photodynamic activity of aluminium sulphophthalocyanine due to biotinylation

Science.gov (United States)

Meerovich, Irina G.; Jerdeva, Victoria V.; Derkacheva, Valentina M.; Meerovich, Gennadii A.; Lukyanets, Eugeny A.; Kogan, Eugenia A.; Savitsky, Alexander P.

2003-09-01

The photodynamic activity of dibiotinylated aluminium sulphophthalocyanine in vitro and in vivo were studied. It was obtained that in vitro dibiotinylated aluminium sulphophthalocyanine provides the effective damage of small cell lung carcinoma OAT-75. In vivo dibiotinylated aluminium sulphophthalocyanine causes destruction of tumor (Erlich carcinoma), results in total necrosis of tumor tissue and expresses vascular damage (trombosis and destruction of vascular walls) even in concentration 0.25 mg/kg of a body weight.

Aluminium supplier selection for the automotive parts manufacturer

Directory of Open Access Journals (Sweden)

M. Cieśla

2016-04-01

Full Text Available This paper presents a methodology for selection of the optimal sources of supply, which is also known as the problem of supplier selection. Theoretical considerations are expanded with research related to aluminium supplier selection for a hypothetical manufacturer of aluminium parts for transportation equipment located in Poland. Evaluation of five suppliers of aluminium from Poland, Germany and Slovenia has been conducted using a weighted scoring method, a strengths and weaknesses method and a graphical method. Choosing the best offer and prioritizing suppliers allows not only the most rational decision in the field of supply logistics to be taken but also the quality of service in the metallurgical industry to be improved.

Monte Carlo simulation of electron depth distribution and backscattering for carbon films deposited on aluminium as a function of incidence angle and primary energy

Science.gov (United States)

Dapor, Maurizio

2005-01-01

Carbon films are deposited on various substrates (polymers, polyester fabrics, polyester yarns, metal alloys) both for experimental and technological motivations (medical devices, biocompatible coatings, food package and so on). Computational studies of the penetration of electron beams in supported thin film of carbon are very useful in order to compare the simulated results with analytical techniques data (obtained by scanning electron microscopy and/or Auger electron spectroscopy) and investigate the film characteristics. In the present paper, the few keV electron depth distribution and backscattering coefficient for the special case of film of carbon deposited on aluminium are investigated, by a Monte Carlo simulation, as a function of the incidence angle and primary electron energy. The simulated results can be used as a way to evaluate the carbon film thickness by a set of measurements of the backscattering coefficient.

Do aluminium-based phosphate binders continue to have a role in contemporary nephrology practice?

Science.gov (United States)

Mudge, David W; Johnson, David W; Hawley, Carmel M; Campbell, Scott B; Isbel, Nicole M; van Eps, Carolyn L; Petrie, James J B

2011-05-13

Aluminium-containing phosphate binders have long been used for treatment of hyperphosphatemia in dialysis patients. Their safety became controversial in the early 1980's after reports of aluminium related neurological and bone disease began to appear. Available historical evidence however, suggests that neurological toxicity may have primarily been caused by excessive exposure to aluminium in dialysis fluid, rather than aluminium-containing oral phosphate binders. Limited evidence suggests that aluminium bone disease may also be on the decline in the era of aluminium removal from dialysis fluid, even with continued use of aluminium binders. The K/DOQI and KDIGO guidelines both suggest avoiding aluminium-containing binders. These guidelines will tend to promote the use of the newer, more expensive binders (lanthanum, sevelamer), which have limited evidence for benefit and, like aluminium, limited long-term safety data. Treating hyperphosphatemia in dialysis patients continues to represent a major challenge, and there is a large body of evidence linking serum phosphate concentrations with mortality. Most nephrologists agree that phosphate binders have the potential to meaningfully reduce mortality in dialysis patients. Aluminium is one of the cheapest, most effective and well tolerated of the class, however there are no prospective or randomised trials examining the efficacy and safety of aluminium as a binder. Aluminium continues to be used as a binder in Australia as well as some other countries, despite concern about the potential for toxicity. There are some data from selected case series that aluminium bone disease may be declining in the era of reduced aluminium content in dialysis fluid, due to rigorous water testing. This paper seeks to revisit the contemporary evidence for the safety record of aluminium-containing binders in dialysis patients. It puts their use into the context of the newer, more expensive binders and increasing concerns about the risks of

Do aluminium-based phosphate binders continue to have a role in contemporary nephrology practice?

Directory of Open Access Journals (Sweden)

van Eps Carolyn L

2011-05-01

Full Text Available Abstract Background Aluminium-containing phosphate binders have long been used for treatment of hyperphosphatemia in dialysis patients. Their safety became controversial in the early 1980's after reports of aluminium related neurological and bone disease began to appear. Available historical evidence however, suggests that neurological toxicity may have primarily been caused by excessive exposure to aluminium in dialysis fluid, rather than aluminium-containing oral phosphate binders. Limited evidence suggests that aluminium bone disease may also be on the decline in the era of aluminium removal from dialysis fluid, even with continued use of aluminium binders. Discussion The K/DOQI and KDIGO guidelines both suggest avoiding aluminium-containing binders. These guidelines will tend to promote the use of the newer, more expensive binders (lanthanum, sevelamer, which have limited evidence for benefit and, like aluminium, limited long-term safety data. Treating hyperphosphatemia in dialysis patients continues to represent a major challenge, and there is a large body of evidence linking serum phosphate concentrations with mortality. Most nephrologists agree that phosphate binders have the potential to meaningfully reduce mortality in dialysis patients. Aluminium is one of the cheapest, most effective and well tolerated of the class, however there are no prospective or randomised trials examining the efficacy and safety of aluminium as a binder. Aluminium continues to be used as a binder in Australia as well as some other countries, despite concern about the potential for toxicity. There are some data from selected case series that aluminium bone disease may be declining in the era of reduced aluminium content in dialysis fluid, due to rigorous water testing. Summary This paper seeks to revisit the contemporary evidence for the safety record of aluminium-containing binders in dialysis patients. It puts their use into the context of the newer, more

Do aluminium-based phosphate binders continue to have a role in contemporary nephrology practice?

Science.gov (United States)

2011-01-01

Background Aluminium-containing phosphate binders have long been used for treatment of hyperphosphatemia in dialysis patients. Their safety became controversial in the early 1980's after reports of aluminium related neurological and bone disease began to appear. Available historical evidence however, suggests that neurological toxicity may have primarily been caused by excessive exposure to aluminium in dialysis fluid, rather than aluminium-containing oral phosphate binders. Limited evidence suggests that aluminium bone disease may also be on the decline in the era of aluminium removal from dialysis fluid, even with continued use of aluminium binders. Discussion The K/DOQI and KDIGO guidelines both suggest avoiding aluminium-containing binders. These guidelines will tend to promote the use of the newer, more expensive binders (lanthanum, sevelamer), which have limited evidence for benefit and, like aluminium, limited long-term safety data. Treating hyperphosphatemia in dialysis patients continues to represent a major challenge, and there is a large body of evidence linking serum phosphate concentrations with mortality. Most nephrologists agree that phosphate binders have the potential to meaningfully reduce mortality in dialysis patients. Aluminium is one of the cheapest, most effective and well tolerated of the class, however there are no prospective or randomised trials examining the efficacy and safety of aluminium as a binder. Aluminium continues to be used as a binder in Australia as well as some other countries, despite concern about the potential for toxicity. There are some data from selected case series that aluminium bone disease may be declining in the era of reduced aluminium content in dialysis fluid, due to rigorous water testing. Summary This paper seeks to revisit the contemporary evidence for the safety record of aluminium-containing binders in dialysis patients. It puts their use into the context of the newer, more expensive binders and increasing

Decomposition of pre calcined aluminium silicate ores of Afghanistan by hydrochloric acid

International Nuclear Information System (INIS)

Khomidi, A.K.; Mamatov, E.D.

2015-01-01

Present article is devoted to decomposition of pre calcined aluminium silicate ores of Afghanistan by hydrochloric acid. The physicochemical properties of initial aluminium silicate ores were studied by means of X-ray phase, differential thermal and silicate analysis. The chemical composition of aluminium containing ores was determined. The optimal conditions of interaction of initial and pre calcined siallites with hydrochloric acid were defined. The kinetics of acid decomposition of aluminium silicate ores was studied as well.

An interesting and efficient green corrosion inhibitor for aluminium ...

African Journals Online (AJOL)

An interesting and efficient green corrosion inhibitor for aluminium from extracts of ... Journal Home > Vol 13, No 1 (2014) > ... possible applications in metal surface anodizing and surface coating in industries. Keywords: Moringa oleifera, Aluminium, Hydrochloric acid, Langmuir isotherm, Plant extracts, Corrosion inhibition ...

Power distribution: conductors in aluminium

International Nuclear Information System (INIS)

Schmid, R.

2007-01-01

This article takes a look at the use of aluminium conductors in medium and low-voltage cables. The author discusses how the increasing price of copper has led to the increasing use of aluminium as a material for the production of the conductors used in medium and low-voltage power cables. Aid is provided that is to help purchasers make the correct decisions when buying medium and low-voltage cables. The current market situation is examined and the appropriate norms are looked at. Technical data and economic aspects are discussed, both for medium and low-voltage applications. The electrical characteristics of the type of cable to be used are examined and discussed

Spectrographic determination of trace impurities in reactor grade aluminium

International Nuclear Information System (INIS)

Chandola, L.C.; Machado, I.J.

1975-01-01

A spectrographic method enabling the determination of 21 trace impurities in aluminium oxide is described. The technique involves mixing the sample with graphite buffer in the ratio 1:1, loading it in a graphite electrode and arcing it for 30 sec. in a dc arc to 10 A current against a pointed graphite cathode. The spectra are photographed on Ilford N.30 emulsion employing a large quartz spectrograph. The aluminium line at 2669.2 A 0 serves as the internal standard. The impurities determined are Ag, B, Bi, Cd, Co, Cr, Cu, Fe, Ga, In, Mg, Mo, Ni, Pb, Sb, Si, Sn, Ti, V and Zn. The sensitivity varies from 5 to 100 ppm and the precision from +- 5 to +- 22% for different elements. A method for converting aluminium metal to aluminium oxide is described. It is found that boron is not lost during this conversion. (author)

Friction and corrosion resistance of sputter deposited supersaturated metastable aluminium-molybdenum alloys

Energy Technology Data Exchange (ETDEWEB)

Abu-Zeid, O.A. [Univ. of the United Arab Emirates, Al-Ain (United Arab Emirates). Dept. of Mech. Eng.; Bates, R.I. [Design, Mfg. and Marketing Research Inst., Univ. of Salford (United Kingdom)

1996-12-15

Two closed field unbalanced magnetrons with targets of aluminium and molybdenum have been used for the co-deposition of aluminium-molybdenum coatings with different compositions. A pin on disk machine and a computer controlled potentiostat have been used to evaluate respectively, the tribological and corrosion properties of the deposited alloys. Results have shown that introducing molybdenum into aluminium coatings improves their poor tribological properties. Aluminium-molybdenum coatings with different compositions have shown low wear behaviour and for coatings with high molybdenum contents (> 80%) friction coefficients against steel, as low as 0.18 have been obtained. The addition of molybdenum into aluminium coatings has reduced their corrosion tendency and corrosion current density in a marine environment. (orig.)

Towards toxicokinetic modelling of aluminium exposure from adjuvants in medicinal products.

Science.gov (United States)

Weisser, Karin; Stübler, Sabine; Matheis, Walter; Huisinga, Wilhelm

2017-08-01

As a potentially toxic agent on nervous system and bone, the safety of aluminium exposure from adjuvants in vaccines and subcutaneous immune therapy (SCIT) products has to be continuously re-evaluated, especially regarding concomitant administrations. For this purpose, knowledge on absorption and disposition of aluminium in plasma and tissues is essential. Pharmacokinetic data after vaccination in humans, however, are not available, and for methodological and ethical reasons difficult to obtain. To overcome these limitations, we discuss the possibility of an in vitro-in silico approach combining a toxicokinetic model for aluminium disposition with biorelevant kinetic absorption parameters from adjuvants. We critically review available kinetic aluminium-26 data for model building and, on the basis of a reparameterized toxicokinetic model (Nolte et al., 2001), we identify main modelling gaps. The potential of in vitro dissolution experiments for the prediction of intramuscular absorption kinetics of aluminium after vaccination is explored. It becomes apparent that there is need for detailed in vitro dissolution and in vivo absorption data to establish an in vitro-in vivo correlation (IVIVC) for aluminium adjuvants. We conclude that a combination of new experimental data and further refinement of the Nolte model has the potential to fill a gap in aluminium risk assessment. Copyright © 2017 Elsevier Inc. All rights reserved.

RESPONSE OF PHENOLIC METABOLISM INDUCED BY ALUMINIUM TOXICITY IN FAGOPYRUM ESCULENTUM MOENCH. PLANTS.

Science.gov (United States)

Smirnov, O E; Kosyan, A M; Kosyk, O I; Taran, N Yu

2015-01-01

Buckwheat genus (Fagopyrum Mill.) is one of the aluminium tolerant taxonomic units of plants. The aim of the study was an evaluation of the aluminium (50 μM effect on phenolic accumulation in various parts of buckwheat plants (Fagopyrum esculentum Moench). Detection of increasing of total phenolic content, changes in flavonoid and anthocyanin content and phenylalanine ammonia-lyase activity (PAL) were revealed over a period of 10 days of exposure to aluminium. The most significant effects of aluminium treatment on phenolic compounds accumulation were total phenolic content increasing (by 27.2%) and PAL activity rising by 2.5 times observed in leaves tissues. Received data could be helpful to understand the aluminium tolerance principles and relationships of phenolic compounds to aluminium phytotoxicity.

Modelling of heterogeneous clustering in aluminium

International Nuclear Information System (INIS)

Smith, A.E.; Bourgeois, L.; Nie, J.-F.; Muddle, B.C.

2003-01-01

Full text: Ab initio modelling of heterogeneous clustering in aluminium has been carried out in order to study the precipitation hardening of alloys. This process is based on the addition of small amounts of solute element to the pure metal. With increasing computational power, atomic scale effects can now be better simulated to determine the nature of the hardening mechanism. Comparisons are made between results obtained from two computational packages. These are the Linear Augmented Plane Wave WEEN2K and the plane wave pseudopotential density functional theory package fhi98md. The study of the optimal geometry of very small size clusters inside aluminium has begun with the testing of initial convergence conditions by determination of binding energies for a variety of super cell sizes of the aluminium host crystal. These are compared with total energy calculations for small size precipitates of copper and transition metals of fixed geometry. Such local optimal determinations are seen as precursors to full Monte Carlo calculations of the notional best local geometry for larger precipitates

Synthesis of aluminium nanoparticles by arc evaporation of an ...

Indian Academy of Sciences (India)

Administrator

Abstract. Aluminium nanoparticles (Al Nps) are synthesized using arc discharge method by applying direct current between aluminium electrodes in liquid environment without any use of vacuum equipment, heat exchangers, high temperatures furnaces and inert gases. After synthesis of Al Nps, in situ coating process on.

The varied functions of aluminium-activated malate transporters–much more than aluminium resistance

Science.gov (United States)

Palmer, Antony J.; Baker, Alison; Muench, Stephen P.

2016-01-01

The ALMT (aluminium-activated malate transporter) family comprises a functionally diverse but structurally similar group of ion channels. They are found ubiquitously in plant species, expressed throughout different tissues, and located in either the plasma membrane or tonoplast. The first family member identified was TaALMT1, discovered in wheat root tips, which was found to be involved in aluminium resistance by means of malate exudation into the soil. However, since this discovery other family members have been shown to have many other functions such as roles in stomatal opening, general anionic homoeostasis, and in economically valuable traits such as fruit flavour. Recent evidence has also shown that ALMT proteins can act as key molecular actors in GABA (γ-aminobutyric acid) signalling, the first evidence that GABA can act as a signal transducer in plants. PMID:27284052

Computer modelling of age hardening for cast aluminium alloys

International Nuclear Information System (INIS)

Wu, Linda; Ferguson, W George

2009-01-01

Age hardening, or precipitation hardening, is one of the most widely adopted techniques for strengthening of aluminium alloys. Although various age hardening models have been developed for aluminium alloys, from the large volume of literature reviewed, it appears that the bulk of the research has been concentrated on wrought aluminium alloys, only a few of the established precipitation models have been applied to the casting aluminium alloys. In the present work, there are two modelling methods that have been developed and applied to the casting aluminium alloys A356 and A357. One is based on the Shercliff-Ashby methodology to produce a process model, by which we mean a mathematical relationship between process variables (alloy composition, ageing temperature and time) and material properties (yield strength or hardness) through microstructure evolution (precipitate radius, volume fraction). The other method is based on the Kampmann and Wagner Numerical (KWN) model which deals with concomitant nucleation, growth and coarsening and is thus capable of predicting the full evolution of the particle size distribution and then a strength model is used to evaluate the resulting change in hardness or yield strength at room temperature by taking into account contributions from lattice resistance, solid solution hardening and precipitation hardening.

Light-weight aluminium bridges and bridge decks. An overview of recent applications

NARCIS (Netherlands)

Maljaars, J.; Soetens, F.; Kluyver, D. de

2008-01-01

The last decades have shown a large increase in the application of aluminium alloys for light-weight bridges. For bridge construction, aluminium alloys have some specific advantages, but also some points of attention. This paper deals with some recent projects of aluminium bridges, and for these

Improving the wettability of 2024 aluminium alloy by means of cold plasma treatment

Science.gov (United States)

Polini, W.; Sorrentino, L.

2003-05-01

Aluminium alloys are heavily used to manufacture structural parts in the aeronautic industry because of its lightness and its corrosion resistance. These alloys are successfully used in other industrial fields too, such as railway, automotive and naval industries. The need to contrast the severe use conditions and the heavy stresses developing in aeronautic field implies to protect the surfaces of the structures in aluminium alloy by any deterioration. To preserve by deterioration, it is necessary to make aluminium more suitable to be coated by protective paint. In the aeronautic industry, a complex and critical process is used in order to enhance both wettability and adhesive properties of aluminium alloy surfaces. Cold plasma treatment represents an efficient, clean and economic alternative to activate aluminium surfaces. The present work deals with air cold plasma treatment of 2024 aluminium alloy surfaces. The influence of dc electrical discharge cold plasma parameters on wettability of 2024 aluminium alloy surfaces has been studied. A set of process variables (voltage, time and air flow rate) has been identified and used to conduct some experimental tests on the basis of design of experiment (DOE) techniques. The experimental results show that the proposed plasma process may considerably increase aluminium alloy wettability. These results represent the first step in trying to optimise the aluminium adhesion by means of this non-conventional manufacturing process.

Microstructure and properties of aluminium-aluminium oxide graded composite materials

Science.gov (United States)

Kamaruzaman, F. F.; Nuruzzaman, D. M.; Ismail, N. M.; Hamedon, Z.; Iqbal, A. K. M. A.; Azhari, A.

2018-03-01

In this research works, four-layered aluminium-aluminium oxide (Al-Al2O3) graded composite materials were fabricated using powder metallurgy (PM) method. In processing, metal-ceramic graded composite materials of 0%, 10%, 20% and 30% weight percentage of ceramic concentration were prepared under 30 ton compaction load using a cylindrical die-punch set made of steel. After that, two-step pressureless sintering was carried out at sintering temperature and time 600°C and 3 hours respectively. It was observed that the sintered cylindrical specimens of 30 mm diameter were prepared successfully. The graded composite specimens were analysed and the properties such as density, microstructure and hardness were measured. It was found that after sintering process, the diameter of the graded cylindrical structure was decreased. Using both Archimedes method and rule of mixture (ROM), he density of structure was measured. The obtained results revealed that the microvickers hardness was increased as the ceramic component increases in the graded layer. Moreover, it was observed that the interface of the graded structure is clearly distinguished within the multilayer stack and the ceramic particles are almost uniformly distributed in the Al matrix.

Development of an on-line electrochemical analyser for trace level aluminium

International Nuclear Information System (INIS)

Chow, Christopher W.K.; Thomas, Shaun D.; Davey, David E.; Mulcahy, Dennis E.; Drikas, Mary

2003-01-01

An in-house designed computerised flow injection (FI) system for low-level aluminium analysis is examined. A simple, low cost electrochemical detection system has been implemented with computerised control and data acquisition system. The system consists of a commercial electrochemical analyser, FI components (manifold, pumps and valves) and an in-house designed control system to perform automated analysis. This system was developed to study aluminium speciation in water, particularly for drinking water. The analytical technique was based upon the complexation reaction between aluminium and a ligand--DASA (1,2-dihydroxy-anthraquinone-3-sulphonic acid). 'Labile' and total aluminium concentrations, Al labile and Al total , respectively, were determined by measuring the sample before and after UV irradiation by amperometry at +0.6 V. The limit of detection for this technique was 10 μg/l (0.37 μM) and the linear calibration range was up to 1.6 mg/l (60 μM) with r 2 value of 0.999. The Al labile /Al total ratios of the water treated by 40, 80 and 100 mg/l of alum using a laboratory scale pilot plant to simulate conventional drinking water treatment processes were found to be 0.4, 0.5 and 0.8, respectively. These results indicated that when higher alum dose was employed, the residual aluminium was present mostly as the 'labile' species. Whereas, if the treatment process was not running at its optimum condition (underdosing), a large portion of aluminium was present as natural organic matter (NOM) - aluminium complexes in the treated water. The system offers a practical and effective means of providing extended knowledge of residual aluminium in drinking water

Aluminium Matrix Composites Reinforced with Co-continuous Interlaced Phases Aluminium-alumina Needles

Directory of Open Access Journals (Sweden)

Elvio de Napole Gregolin

2002-09-01

Full Text Available An Al-5SiO2 (5 wt% of SiO2 aluminium matrix fiber composite was produced where the reinforcement consists of fossil silica fibers needles. After being heat-treated at 600 °C, the original fiber morphology was retained but its microstructure changed from solid silica to an interconnected (Al-Si/Al2O3 interlaced structure named co-continuous composite. A technique of powder metallurgy, using commercial aluminium powder and the silica fibers as starting materials, followed by hot extrusion, was used to produce the composite. The co-continuous microstructure was obtained partially or totally on the fibers as a result of the reaction, which occurs during the heat treatment, first by solid diffusion and finally by the liquid Al-Si in local equilibrium, formed with the silicon released by reaction. The internal structure of the fibers was characterized using field emission electron microscope (FEG-SEM and optical microscopy on polished and fractured samples.

Aluminium alloys in municipal solid waste incineration bottom ash.

Science.gov (United States)

Hu, Yanjun; Rem, Peter

2009-05-01

With the increasing growth of incineration of household waste, more and more aluminium is retained in municipal solid waste incinerator bottom ash. Therefore recycling of aluminium from bottom ash becomes increasingly important. Previous research suggests that aluminium from different sources is found in different size fractions resulting in different recycling rates. The purpose of this study was to develop analytical and sampling techniques to measure the particle size distribution of individual alloys in bottom ash. In particular, cast aluminium alloys were investigated. Based on the particle size distribution it was computed how well these alloys were recovered in a typical state-of-the-art treatment plant. Assessment of the cast alloy distribution was carried out by wet physical separation processes, as well as chemical methods, X-ray fluorescence analysis and electron microprobe analysis. The results from laboratory analyses showed that cast alloys tend to concentrate in the coarser fractions and therefore are better recovered in bottom ash treatment plants.

Trace aluminium determination and sampling problems of archeological bone employing destructive neutron activation analysis

International Nuclear Information System (INIS)

Blotcky, A.J.; Rack, E.P.; Recker, R.R.; Leffler, J.A.; Teitelbaum, S.

1978-01-01

A destructive neutron activation analysis procedure was developed for determining trace aluminium content in bone. The method is based on a carefully planned sample preparation, irradiation at a neutron flux for 3.1x10 11 nxcm -2 xs -1 for 5 minutes, and chemical separation based on ion exchange. It was found that bone samples soaked in aluminium containing soil gave highly elevated aluminium values as a result of the aluminium adsorption into the bone matrix. The maximum aluminium content values for prehistoric bones are larger than those of modern bones and comparable to aluminium levels present in bone from renal patients. (T.G.)

Fire exposed aluminium structures

NARCIS (Netherlands)

Maljaars, J.; Fellinger, J.E.J.; Soetens, F.

2005-01-01

Material properties and mechanical response models for fire design of steel structures are based on extensive research and experience. Contrarily, the behaviour of aluminium load bearing structures exposed to fire is relatively unexplored. This article gives an overview of physical and mechanical

Manufacturing and Machining Challenges of Hybrid Aluminium Metal Matix Composites

Science.gov (United States)

Baburaja, Kammuluri; Sainadh Teja, S.; Karthik Sri, D.; Kuldeep, J.; Gowtham, V.

2017-08-01

Manufacturing which involves material removal processes or material addition processes or material transformation processes. One or all the processes to obtain the final desired properties for a material with desired shape which meets the required precision and accuracy values for the expected service life of a material in working conditions. Researchers found the utility of aluminium to be the second largest after steel. Aluminium and its metal matrix composite possess wide applications in various applications in aerospace industry, automobile industry, Constructions and even in kitchen utensils. Hybrid Al-MMCconsist of two different materials, and one will be from organic origin along with the base material. In this paper an attempt is made to bring out the importance of utilization of aluminium and the challenges concerned in manufacturing and machining of hybrid aluminium MMC.

Chemical mimicking of bio-assisted aluminium extraction by Aspergillus niger's exometabolites.

Science.gov (United States)

Boriová, Katarína; Urík, Martin; Bujdoš, Marek; Pifková, Ivana; Matúš, Peter

2016-11-01

Presence of microorganisms in soils strongly affects mobility of metals. This fact is often excluded when mobile metal fraction in soil is studied using extraction procedures. Thus, the first objective of this paper was to evaluate strain Aspergillus niger's exometabolites contribution on aluminium mobilization. Fungal exudates collected in various time intervals during cultivation were analyzed and used for two-step bio-assisted extraction of alumina and gibbsite. Oxalic, citric and gluconic acids were identified in collected culture media with concentrations up to 68.4, 2.0 and 16.5 mmol L -1 , respectively. These exometabolites proved to be the most efficient agents in mobile aluminium fraction extraction with aluminium extraction efficiency reaching almost 2.2%. However, fungal cultivation is time demanding process. Therefore, the second objective was to simplify acquisition of equally efficient extracting agent by chemically mimicking composition of main organic acid components of fungal exudates. This was successfully achieved with organic acids mixture prepared according to medium composition collected on the 12th day of Aspergillus niger cultivation. This mixture extracted similar amounts of aluminium from alumina compared to culture medium. The aluminium extraction efficiency from gibbsite by organic acids mixture was lesser than 0.09% which is most likely because of more rigid mineral structure of gibbsite compared to alumina. The prepared organic acid mixture was then successfully applied for aluminium extraction from soil samples and compared to standard single step extraction techniques. This showed there is at least 2.9 times higher content of mobile aluminium fraction in soils than it was previously considered, if contribution of microbial metabolites is considered in extraction procedures. Thus, our contribution highlights the significance of fungal metabolites in aluminium extraction from environmental samples, but it also simplifies the

Electrical connection for aluminium conductors in automotive applications : Prestudy of available solutions for electrical connection methods of aluminium cables

OpenAIRE

Hamedi, Emilia

2017-01-01

Due to increasing weight of electrical component and wiring harnesses in a vehicle contrary to the demand of light constructed vehicles as well as the constantly increasing and fluctuating price of copper compared to aluminium’s stable and far lower price, the use of aluminium conductors as an alternative have been promoted.  This thesis work lay theoretical research of the available methods used for electrical connection of aluminium conductors in order to increase the knowledge about the av...

Determination of total mercury in aluminium industrial zones and soil contaminated with red mud.

Science.gov (United States)

Rasulov, Oqil; Zacharová, Andrea; Schwarz, Marián

2017-08-01

This study investigated total mercury contents in areas impacted by aluminium plants in Tajikistan and Slovakia and in one area flooded with red mud in Hungary. We present the first determination of total mercury contents in the near-top soil (0-10 and 10-20 cm) in Tajikistan and the first comparative investigation of Tajikistan-Slovakia-Hungary. The Tajik Aluminium Company (TALCO) is one of the leading producers of primary aluminium in Central Asia. In the past 30 years, the plant has been producing large volumes of industrial waste, resulting in negative impacts on soil, groundwater and air quality of the surrounding region. Mercury concentrations were significant in Slovakia and Hungary, 6 years after the flooding. In studied areas in Slovakia and Hungary, concentrations of total mercury exceeded the threshold limit value (TLV = 0.5 mg Hg kg -1 ). However, in Tajikistan, values were below the TLV (0.006-0.074 mg kg -1 ) and did not significantly vary between depths. Total Hg in Slovakia ranged from 0.057 to 0.668 mg kg -1 and in Hungary from 0.029 to 1.275 mg kg -1 . However, in the plots near to the red mud reservoir and the flooded area, Hg concentrations were higher in the upper layers than in the lower ones.

Measurement of oxide-layer thickness of internal granules in high-purity aluminium

International Nuclear Information System (INIS)

Takacs, S.; Ditroi, F.; Mahunka, I.

1989-01-01

Charged-particle activation analysis was used for the determination of bulk oxygen concentration in aluminium. High-purity aluminium samples and mixtures containing different amounts of alumina were irradiated by 13 MeV 3 He particles. The aim of the investigation was to determine the oxide-layer thickness on the surface of internal aluminium granules. The measurement was carried out by determining the bulk oxygen concentration in the samples, and calculating the oxide-layer thickness, by using model conditions about the microstructure of the aluminium samples. (author) 5 refs

Selective Sulfidation of Lead Smelter Slag with Sulfur

Science.gov (United States)

Han, Junwei; Liu, Wei; Wang, Dawei; Jiao, Fen; Qin, Wenqing

2016-02-01

The selective sulfidation of lead smelter slag with sulfur was studied. The effects of temperature, sulfur dosage, carbon, and Na salts additions were investigated based on thermodynamic calculation. The results indicated that more than 96 pct of zinc in the slag could be converted into sulfides. Increasing temperature, sulfur dosage, or Na salts dosage was conducive to the sulfidation of the zinc oxides in the slag. High temperature and excess Na salts would result in the more consumption of carbon and sulfur. Carbon addition not only promoted the selective sulfidation but reduced the sulfur dosage and eliminated the generation of SO2. Iron oxides had a buffering role on the sulfur efficient utilization. The transformation of sphalerite to wurtzite was feasible under reducing condition at high temperature, especially above 1273 K (1000 °C). The growth of ZnS particles largely depended upon the roasting temperature. They were significantly increased when the temperature was above 1273 K (1000 °C), which was attributed to the formation of a liquid phase.

The varied functions of aluminium-activated malate transporters-much more than aluminium resistance.

Science.gov (United States)

Palmer, Antony J; Baker, Alison; Muench, Stephen P

2016-06-15

The ALMT (aluminium-activated malate transporter) family comprises a functionally diverse but structurally similar group of ion channels. They are found ubiquitously in plant species, expressed throughout different tissues, and located in either the plasma membrane or tonoplast. The first family member identified was TaALMT1, discovered in wheat root tips, which was found to be involved in aluminium resistance by means of malate exudation into the soil. However, since this discovery other family members have been shown to have many other functions such as roles in stomatal opening, general anionic homoeostasis, and in economically valuable traits such as fruit flavour. Recent evidence has also shown that ALMT proteins can act as key molecular actors in GABA (γ-aminobutyric acid) signalling, the first evidence that GABA can act as a signal transducer in plants. © 2016 The Author(s). Published by Portland Press Limited on behalf of the Biochemical Society.

Corrosion of research reactor aluminium clad spent fuel in water

International Nuclear Information System (INIS)

2003-01-01

This report describes research performed in ten laboratories within the framework of the IAEA Co-ordinated Research Project on Corrosion of Research Reactor Aluminium Clad Spent Fuel in Water. The project consisted of exposure of standard racks of corrosion coupons in the spent fuel pools of the participating research reactor laboratories and the evaluation of the coupons after predetermined exposure times, along with periodic monitoring of the storage water. A group of experts in the field contributed a state of the art review and provided technical supervision of the project. Localized corrosion mechanisms are notoriously difficult to understand, and it was clear from the outset that obtaining consistency in the results and their interpretation from laboratory to laboratory would depend on the development of an excellent set of experimental protocols. These experimental protocols are described in the report together with guidelines for the maintenance of optimum water chemistry to minimize the corrosion of aluminium clad research reactor fuel in wet storage. A large database on corrosion of aluminium clad materials has been generated from the CRP and the SRS corrosion surveillance programme. An evaluation of these data indicates that the most important factors contributing to the corrosion of the aluminium are: (1) High water conductivity (100-200 μS/cm); (2) Aggressive impurity ion concentrations (Cl - ); (3) Deposition of cathodic particles on aluminium (Fe, etc.); (4) Sludge (containing Fe, Cl - and other ions in concentrations greater than ten times the concentrations in the water); (5) Galvanic couples between dissimilar metals (stainless steel-aluminium, aluminium-uranium, etc); (6) Scratches and imperfections (in protective oxide coating on cladding); (7) Poor water circulation. These factors operating both independently and synergistically may cause corrosion of the aluminium. The single most important key to preventing corrosion is maintaining good

Heavy metal content of lichens in relation to distance from a nickel smelter in Sudbury, Ontario

Energy Technology Data Exchange (ETDEWEB)

Nieboer, E; Ahmed, H M; Puckett, K J; Richardson, D H.S.

1972-01-01

The Sudbury region of Ontario has large deposits of nickel, iron, and copper, and thus a number of smelting plants which produce sulfur dioxide and heavy metal pollution. Since lichens are good indicators of SO/sub 2/ pollution levels, the pattern of heavy metal content in lichen species in the area of a copper smelter in Sudbury was correlated with distance from the smelter to ascertain whether lichens might also be good indicators of the amount of heavy metal fallout. The lichens were analyzed qualitatively and quantitatively. All seven species of lichens contained copper, iron, zinc, nickel, manganese, and lead. Cadmium and cobalt were detected in two species. Neither gold nor silver could be identified in lichen material with the tests used. A pollution model was developed and compared to field results. The simple dilution of the stack effluent was consistent with the fact that the lichen metal content was related to the reciprocal of the distance from the pollution source. The lichens from the area could tolerate simultaneously high concentrations of several heavy metals that are known to be toxic to other plants. The mechanism of metal uptake was not clearly established. The study showed that lichens and other epiphytes are potentially the most useful indicators of heavy metal fallout around industrial plants.

Treatment of metallurgical wastes : recovery of metal values from smelter slags by pressure oxidative leaching

Energy Technology Data Exchange (ETDEWEB)

Li, Y.; Perederiy, I.; Papangelakis, V.G. [Toronto Univ., ON (Canada). Dept. of Chemical Engineering and Applied Chemistry

2008-07-01

Vast quantities of slag are produced and dumped as waste by-products during the production of base metals by smelting operations. These slags contain large amounts of valuable metals which lead to a decrease in metal yield and, combined with the entrapped sulphur, pose a danger to the environment. The dissolution of fayalite is important for the selective recovery of valuable metals and the cleanup of slags in high pressure oxidative leaching. The nature of base metals and iron in solidified slag must be investigated in order to understand the mechanism of the process. This paper discussed the application of powder X-ray diffraction (PXRD) and scanning electron microscopy (SEM) for the characterization of a smelter slag microstructure. The study used leaching tests with the same smelter slag to measure and monitor the results of leaching, including metal extraction levels, the extent of iron dissolution as well as impurity contents. The paper provided information on the experiment with particular reference to slag leaching, chemical analysis, and characterization. It was concluded that slag consists of several solid phases with base metal sulfide and oxide droplets entrapped in the fayalite matrix or silica regions. Therefore, nickel, copper, cobalt, and zinc need to be exposed either chemically or mechanically to promote their recovery. 21 refs., 4 tabs., 5 figs.

Electrotransport of hydrogen in aluminium at 20 and 800 deg C

International Nuclear Information System (INIS)

Byalik, O.M.; Volkotrub, N.P.; Pinchuk, V.M.; Golub, L.V.; Degtyarenko, G.E.; Ivanchuk, D.F.

1982-01-01

Electrotransport of hydrogen in the field of crystal lattice of aluminium is investigated at the special installation using the method of measurement of electric resistivity. Quantum-mechanical calculation of H + and H - ions interaction with aluminium atoms is made to clarify the mechanizm of electrotransport. It is shown, that probability of the H + and H - ions permeation in the field of aluminium crystal lattice can be judged by the ratio of δE 1 (the lattice potential barrier) and δ 2 (the local energy minium in the case of atom arrangement in the lattice plane). The value of potentials of hydrogen ions interaction with aluminium lattice is obtained in the result os solution of the Schroedinger equation

AE Monitoring of Diamond Turned Rapidly Soldified Aluminium 443

International Nuclear Information System (INIS)

Onwuka, G; Abou-El-Hossein, K; Mkoko, Z

2017-01-01

The fast replacement of conventional aluminium with rapidly solidified aluminium alloys has become a noticeable trend in the current manufacturing industries involved in the production of optics and optical molding inserts. This is as a result of the improved performance and durability of rapidly solidified aluminium alloys when compared to conventional aluminium. Melt spinning process is vital for manufacturing rapidly solidified aluminium alloys like RSA 905, RSA 6061 and RSA 443 which are common in the industries today. RSA 443 is a newly developed alloy with few research findings and huge research potential. There is no available literature focused on monitoring the machining of RSA 443 alloys. In this research, Acoustic Emission sensing technique was applied to monitor the single point diamond turning of RSA 443 on an ultrahigh precision lathe machine. The machining process was carried out after careful selection of feed, speed and depths of cut. The monitoring process was achieved with a high sampling data acquisition system using different tools while concurrent measurement of the surface roughness and tool wear were initiated after covering a total feed distance of 13km. An increasing trend of raw AE spikes and peak to peak signal were observed with an increase in the surface roughness and tool wear values. Hence, acoustic emission sensing technique proves to be an effective monitoring method for the machining of RSA 443 alloy. (paper)

Sol gel synthesis for preparation of yttrium aluminium garnet

NARCIS (Netherlands)

Vrolijk, J.W.G.A.; Willems, J.W.M.M.; Metselaar, R.; With, de G.; Terpstra, R.A.; Metselaar, R.

1989-01-01

Sol-gel—synthesis for preparation of pure yttrium aluminium garnet powder with small grain size is subject of this ongoing study. Starting materials were sulfates and chlorides of yttrium and aluminium. To obtain pure YAG (Y3A1SO1Z) pH during hydrolysis as well as temperature during calcination and

Defect generation during solidification of aluminium foams

International Nuclear Information System (INIS)

Mukherjee, M.; Garcia-Moreno, F.; Banhart, J.

2010-01-01

The reason for the frequent occurrence of cell wall defects in metal foams was investigated. Aluminium foams often expand during solidification, a process which is referred as solidification expansion (SE). The effect of SE on the structure of aluminium foams was studied in situ by X-ray radioscopy and ex situ by X-ray tomography. A direct correlation between the magnitude of SE and the number of cell wall ruptures during SE and finally the number of defects in the solidified foams was found.

Aluminium, extractable from soil samples by the acid ammonium acetate soil-testing method

Directory of Open Access Journals (Sweden)

Osmo Mäkitie

1968-05-01

Full Text Available The extractant, 0.5 M acetic acid –0.5 M ammonium acetate at pH 4.65, which is used in soil-testing, extracts relatively high amounts of aluminium from acid soils. The mean values of acetate-extractable aluminium at pH 4.65, 1.75 meq Al/100 g of soil, and of exchangeable aluminium (M KCI extraction, 0.41 meq Al were obtained from a material of 30 samples of acid soils (Table 2. Several other acetic acid ammonium acetate extractants, from M acetic acid to M ammonium acetate solution were also used for studying the extractability of soil aluminium. The soil-testing extractant can be used for the estimation of the soluble amounts of aluminium in acid soils, however, further studies are needed for a better interpretation of the ammonium acetate extractable (at pH 4.65 aluminium in our soils.

Crystal structure and phase composition of aluminium thin films with holmium additions

International Nuclear Information System (INIS)

Koleshko, V.M.; Belitskij, V.F.; Obukhov, V.E.; Rumak, N.V.; Urban, T.P.

1984-01-01

The effect of holmium additions on the crystal structure and phase composition of thin aluminium films has been studied. A regularity in grain size changes in aluminium thin films versus the holmium content in them is established. The holmium introduction is shown to result in the appearance of axial texture in the aluminium films, the texture axis being determined by the quantity of the addition. During heat treatment of the aluminium films, containing holmium additions, in the range of low ( approximately 100-200 deg C) annealing temperatures holmium monohydroxide is formed, and at annealing temperatures 300 deg C 0 3 is formed

Decreasing emissions of a secondary lead smelter by installation of a battery breaker. Emissionsminderung einer Sekundaerbleihuette durch Integration einer Akkuschrott-Aufbereitung

Energy Technology Data Exchange (ETDEWEB)

Lamm, K F

1986-11-01

Dust and lead emissions of a secondary lead smelter mainly from the area of stockyards, handling, transport, charge preparing as well as the further treatment in rotary furnaces. A 60% decrease is obtained by compact assembling of covered battery stockyard, battery breaker and charge preparation and direct connection to the existing smelter area. The breaker itself contains a wet screen trommel and a filter press for separation of paste. The heavy-media sink-float-system has been replaced by dynamic water separation, which results in cleaner qualities of all fractions. In spite of a 100% wet separation plant, a bagfilter can be used with expected clean gas dust contents below 5 mg/m{sup 3} and below 2.5 mg Pb/m{sup 3}. Over a 2 years-period, dust and lead contents have been below 1 mg/m{sup 3}. (orig.) With 5 refs., 2 flowsheets, 10 figs.

Arsenic accumulation in people working with and living near a gold smelter

International Nuclear Information System (INIS)

Jervis, R.E.; Tiefenbach, B.; Toronto Univ., Ontario

1979-01-01

The processing of arsenic-containing ores for the recovery of metals such as gold, copper or lead can cause both an occupational health hazard to smelter workers and an environmental health problem to persons living downwind from the refineries. The study reported is a follow-up to preliminary investigations of possible arsenic ingestion by native children living near a gold refinery at Yellowknife, N.W.T., Canada and of a few mine-mill workers. Instrumental neutron activation of lake water and melted snow used as drinking water as well as of scalp hair gave evidence of appreciable intake of arsenic and some mercury. A further set of 67 hair samples was obtained from most of the smelter workers and from children in a native settlement who were considered most vulnerable, augmented by a set of 26 control samples from steel workers and children living in a comparable (but arsenic-free) northern area about 1000 km distance at Whitehorse, Yukon. Hair arsenic levels were consistently elevated above the controls, ranging to 280 ppm in one worker. The water supplies ranged up to 3 ppm, well above the 0.05 ppm MPC for drinking water. A larger epidemiological study of the area and of Hay River, N.W.T. controls, done in association with electromyography, was just completed and involved a further 414 children and workers from Yellowknife and 105 from the control area. The mean hair arsenic of 6.7 ppm for the former was quite different from a result of 0.33 ppm for the Hay River group, and 33% of the Yellowknife subjects were elevated above 1 ppm but none of the controls were above this concentration. Four workers were above 100 ppm, ranging as high as 620 ppm hair arsenic

The effects of aluminium and selenium supplementation on brain ...

African Journals Online (AJOL)

This in vivo study was designed to investigate the potential of aluminium (Al), in the absence of added iron, to participate in either antioxidant or pro-oxidant events. Some markers of oxidative stress were determined in liver and brain of rats exposed to aluminium lactate, either alone or in the presence of dietary supplements ...

Potentiometric determination of the 'formal' hydrolysis ratio of aluminium species in aqueous solutions

International Nuclear Information System (INIS)

Fournier, Agathe C.; Shafran, Kirill L.; Perry, Carole C.

2008-01-01

The 'formal' hydrolysis ratio (h = C(OH - ) added /C(Al) total ) of hydrolysed aluminium-ions is an important parameter required for the exhaustive and quantitative speciation-fractionation of aluminium in aqueous solutions. This paper describes a potentiometric method for determination of the formal hydrolysis ratio based on an automated alkaline titration procedure. The method uses the point of precipitation of aluminium hydroxide as a reference (h = 3.0) in order to calculate the initial formal hydrolysis ratio of hydrolysed aluminium-ion solutions. Several solutions of pure hydrolytic species including aluminium monomers (AlCl 3 ), Al 13 polynuclear cluster ([Al 13 O 4 (OH) 24 (H 2 O) 12 ] 7+ ), Al 30 polynuclear cluster ([Al 30 O 8 (OH) 56 (H 2 O) 26 ] 18+ ) and a suspension of nanoparticulate aluminium hydroxide have been used as 'reference standards' to validate the proposed potentiometric method. Other important variables in the potentiometric determination of the hydrolysis ratio have also been optimised including the concentration of aluminium and the type and strength of alkali (Trizma-base, NH 3 , NaHCO 3 , Na 2 CO 3 and KOH). The results of the potentiometric analysis have been cross-verified by quantitative 27 Al solution nuclear magnetic resonance ( 27 Al NMR) measurements. The 'formal' hydrolysis ratio of a commercial basic aluminium chloride has been measured as an example of a practical application of the developed technique

Aluminium concentration versus the base cation to aluminium ratio as predictors for aluminium toxicity in Pinus sylvestris and Picea abies seedlings

NARCIS (Netherlands)

Schöll, van L.; Keltjens, W.G.; Hoffland, E.; Breemen, van N.

2004-01-01

Aluminium (Al) toxicity is considered an important factor in forest deterioration caused by soil acidification. A ratio of base cations (BC) to Al in the soil solution lower than 1 is widely used as an indicator for potentially adverse effects on tree health. In our view, the validity of the

EXPERIMENTAL INVESTIGATION ON TRIBOLOGICAL CHARACTERISTICS OF SILICON NITRIDE REINFORCED ALUMINIUM METAL MATRIX COMPOSITES

Directory of Open Access Journals (Sweden)

D. BHUVANESH

2017-05-01

Full Text Available Aluminium alloy (LM25 reinforced with silicon nitride was fabricated by liquid metallurgy route. The fabricated composite was investigated for dry sliding wear behaviour by conducting experiments using pin-on-disc tribometer. Set of experiments were planned using Taguchi’s technique and data analysis was carried out using L27 orthogonal array. Analysis of Variance (ANOVA technique was used to determine the significance of parameter with respect to wear rate. Signal-to-Noise ratio was employed to detect the most and least influential parameter as well as their level of influence. ‘Smaller the wear’ characteristic was chosen for the analysis of dry sliding wear. Results implied that, the load has the primary effect on the wear succeeded by the effect of sliding velocity and sliding distance. Scanning Electronic Microscopic studies were carried out on worn surfaces to understand the wear mechanism.Tribological results indicated that LM25 aluminium alloy could be better utilized as a material for piston, rotor and bearings for long life in low speed applications.

Effect of microcrystallization on pitting corrosion of pure aluminium

International Nuclear Information System (INIS)

Meng Guozhe; Wei Liyan; Zhang Tao; Shao Yawei; Wang Fuhui; Dong Chaofang; Li Xiaogang

2009-01-01

A microcrystalline aluminium film with grain size of about 400 nm was prepared by magnetron sputtering technique. Its corrosion behaviour was investigated in NaCl containing acidic solution by means of potentiodynamic polarization curves and electrochemical noise (EN). The polarization results indicated that the corrosion potential of the sample shifted towards more positive direction, while its corrosion current density decreased compared with that of pure coarse-grain Al. The EN analysis based on stochastic model demonstrated that there existed two kinds of effect of microcrystallization on the pitting behaviour of pure aluminium: (1) the rate of pit initiation is accelerated, (2) the pit growth process was impeded. This leads to the enhancement of pitting resistance for the microcrystallized aluminium.

Three body abrasion of laser surface alloyed aluminium AA1200

CSIR Research Space (South Africa)

Mabhali, Luyolo AB

2012-06-01

Full Text Available Laser surface alloying of aluminium AA1200 was performed with a 4 kW Nd:YAG laser to improve the abrasion wear resistance. Aluminium surfaces reinforced with metal matrix composites and intermetallic phases were achieved. The phases present depended...

Neutron activation analysis of baths forming conversion layer on aluminium

International Nuclear Information System (INIS)

Szilagyi, Istvan; Maleczki, Emil; Bodizs, Denes

1988-01-01

Chromate layers were formed on the surface of aluminium using yellow and green chromating solutions. For the determination of the aluminium content neutron activation method was used. Nuclear effects disturbing the determination were eliminated by double irradiation technique. (author) 8 refs.; 4 figs

Dietary exposure to aluminium and health risk assessment in the residents of Shenzhen, China.

Science.gov (United States)

Yang, Mei; Jiang, Lixin; Huang, Huiping; Zeng, Shengbo; Qiu, Fen; Yu, Miao; Li, Xiaorong; Wei, Sheng

2014-01-01

Although there are great changes of dietary in the past few decades in China, few are known about the aluminium exposure in Chinese diet. The aim of this study is to systematically evaluate the dietary aluminium intake level in residents of Shenzhen, China. A total of 853 persons from 244 household were investigated their diet by three days food records. Finally, 149 kinds of foods in 17 food groups were selected to be the most consumed foods. From them, 1399 food samples were collected from market to test aluminium concentration. High aluminium levels were found in jellyfish (median, 527.5 mg/kg), fried twisted cruller (median, 466.0 mg/kg), shell (median, 107.1 mg/kg). The Shenzhen residents' average dietary aluminium exposure was estimated at 1.263 mg/kg bw/week which is lower than the PTWI (provisional tolerable weekly intake). But 0-2 and 3-13 age groups have the highest aluminium intake exceeding the PTWI (3.356 mg/kg bw/week and 3.248 mg/kg bw/week) than other age groups. And the main dietary aluminium exposure sources are fried twisted cruller, leaf vegetables and bean products. Our study suggested that even three decades rapid economy development, children in Shenzhen still have high dietary aluminium exposure risk. How to control high dietary aluminium exposure still is a great public health challenge in Shenzhen, China.

Decomposition of oxidezed lead and aluminium thin films on molybdenum substrates

International Nuclear Information System (INIS)

Makarovskij, N.A.

1981-01-01

The decomposition of oxidized solid phase lead and aluminium thin films on molybdenum substrates in the process of diffusion annealing in the 5x10 -5 mm Hg vacuum at temperatures from 280 to 320 deg C and from 500 to 560 deg C, respectively, is investigated. The conclusion is made that failure of oxidized lead and aluminium thin film coatings is carried out by the mechanism of volumetric self-diffusion. Experimentally established values of activation energies of the process of lead (Qsub(Mo)sup(Pb)=29 kcal/mol) and aluminium (Qsub(Mo)sup(Al)=35 kcal/mol) film failure are close to corresponding activation energies of lead and aluminium volumetric self-diffusion, which agrees with the conclusions made [ru

Corrosion Inhibition of Aluminium in Acid Media By Citrullus Colocynthis Extract

Directory of Open Access Journals (Sweden)

Rajkiran Chauhan

2011-01-01

Full Text Available Inhibition of corrosion of aluminium in acid solution by methanol extract of Citrullus colocynthis plant has been studied using mass loss and thermometric measurements. It has been found that the plant extract act as a good corrosion inhibitor for aluminium in all concentrations of sulphuric and hydrochloric acid solution. The inhibition action depends on the concentration of acid and inhibitor. Results for mass loss and thermometric measurement indicate that inhibition efficiency increase with increasing inhibitor concentration. The inhibition action of the plant extract is discussed in view of Langmuir adsorption isotherm. It has been observed that the adsorption of the extract on aluminium surface is a spontaneous process. The plant extract provides a good protection to aluminium against corrosion.

Method of preparing an Al-Ti-B grain refiner for aluminium-comprising products, and a method of casting aluminium products

OpenAIRE

Brinkman, H.J.; Duszczyk, J.; Katgerman, L.

1999-01-01

The invention relates to a method of preparing an Al-Ti-B grain refiner for cast aluminium-comprising products. According to the invention the preparation is realized by mixing powders selected from the group comprising aluminium, titanium, boron, and alloys and intermetallic compounds thereof, compressing, heating in an inert environment until an exothermic reaction is initiated and cooling. It has been shown that when the grain refiner thus prepared is applied, the quality of cast products ...

Impacts of landscape remediation on the heavy metal pollution dynamics of a lake surrounded by non-ferrous smelter waste

Energy Technology Data Exchange (ETDEWEB)

Blake, William H. [Department of Geography, University of Wales, Swansea SA2 8PP (United Kingdom)]. E-mail: william.blake@plymouth.ac.uk; Walsh, Rory P.D. [Department of Geography, University of Wales, Swansea SA2 8PP (United Kingdom); Reed, Jane M. [Department of Geography, University of Hull, Cottingham Road, Hull HU6 7RX (United Kingdom); Barnsley, Michael J. [Department of Geography, University of Wales, Swansea SA2 8PP (United Kingdom); Smith, Jamie [Department of Geography, University of Wales, Swansea SA2 8PP (United Kingdom)

2007-07-15

Heavy metal concentrations and potential bioavailability are reported for sediment in a shallow flood detention lake surrounded by reclaimed, smelter-contaminated land. A range of sediment column proxy indicators is used to explore changes in pollution dynamics with remediation. Sediment concentrations of Pb and Zn are high at {approx}600 and 20 000 mg kg{sup -1}, respectively. Less than 7% of total Pb is potentially bioavailable following sequential extraction as opposed to 47% of Zn. Metal transfer mechanisms to lake sediment include detrital inputs, scavenging by particulates and biogeochemical precipitation. Sedimentary evidence indicates that detrital inputs to the lake declined following land reclamation after which it is proposed that dissolved inputs increased with leaching of reworked waste material. Whilst downcore metal profiles may be subject to post-depositional change, diatom analysis suggests more recent improvements in water quality. The potential for post-remediation pollution episodes relating to metal release from historic sedimentary stores should be considered in future remediation strategies. - The contaminant hydrology of reworked smelter spoil is complex.

Impacts of landscape remediation on the heavy metal pollution dynamics of a lake surrounded by non-ferrous smelter waste

International Nuclear Information System (INIS)

Blake, William H.; Walsh, Rory P.D.; Reed, Jane M.; Barnsley, Michael J.; Smith, Jamie

2007-01-01

Heavy metal concentrations and potential bioavailability are reported for sediment in a shallow flood detention lake surrounded by reclaimed, smelter-contaminated land. A range of sediment column proxy indicators is used to explore changes in pollution dynamics with remediation. Sediment concentrations of Pb and Zn are high at ∼600 and 20 000 mg kg -1 , respectively. Less than 7% of total Pb is potentially bioavailable following sequential extraction as opposed to 47% of Zn. Metal transfer mechanisms to lake sediment include detrital inputs, scavenging by particulates and biogeochemical precipitation. Sedimentary evidence indicates that detrital inputs to the lake declined following land reclamation after which it is proposed that dissolved inputs increased with leaching of reworked waste material. Whilst downcore metal profiles may be subject to post-depositional change, diatom analysis suggests more recent improvements in water quality. The potential for post-remediation pollution episodes relating to metal release from historic sedimentary stores should be considered in future remediation strategies. - The contaminant hydrology of reworked smelter spoil is complex

An aluminium evaporation source for ion plating

International Nuclear Information System (INIS)

Walley, P.A.; Cross, K.B.

1977-01-01

Ion plating with aluminium is becoming increasingly accepted as a method of anti-corrosion surface passivation, the usual requirements being for a layer between 12 and 50 microns in thickness, (0.0005 to 0.002). The evaporation system described here offers a number of advantages over high power electron beam sources when used for aluminium ion plating. The source consists of a resistively heated, specially shaped, boron nitride-titanium diboride boat and a metering feed system. Its main features are small physical size, soft vacuum compatibility, low power consumption and metered evaporation output. (author)

Bioactive type glass-ceramics within incorporated aluminium

International Nuclear Information System (INIS)

Volzone, C.; Stabile, F.M.; Ortiga, J.

2012-01-01

Bioactive glass-ceramics are used as biomaterials for the reparation of bone tissue. They are prepared, generally, by bioglass of specific composition for each particular use. The aluminium addition in the formulation at very small quantities influences on the structural properties. Two glass-ceramics obtained by P 2 O 5 -Na 2 O-CaO-SiO 2 formulation within aluminium (0.5 % in Al 2 O 3 base) added through a reactive alumina and purified feldspar were analyzed. The results showed structural differences between both glass-ceramics. (author)

Aluminium-rich corner in Al-Cu-La system

International Nuclear Information System (INIS)

Yunusov, I.; Ganiev, I.N.

1990-01-01

Aluminium corner of Al-Cu-La system are investigated by means of microstructural and differential thermal analysis. Existence of LaCu 2 Al 10 and LaCu 0.5 Al 3.5 ternary compounds in the system is confirmed and it is shown, as well, both compounds are in two-phase equilibrium with aluminium solid solution and form with it and between each other eutectic type state diagrams. State diagrams for quasibinary sections are plotted

Elastic and plastic properties of iron-aluminium alloys. Special problems raised by the brittleness of alloys of high aluminium content

International Nuclear Information System (INIS)

Mouturat, P.

1966-06-01

The present study embodies the results obtained with iron-aluminium alloys whose composition runs from 0 to nearly 50 atoms per cent aluminium. Conditions of elaboration and transformation have been studied successively, as well as the Young's modulus and the flow stress; the last chapter embodies, a study of the Portevin-le-Chatelier effect in alloys of 40 atoms per cent of aluminium. I) The principal difficulty to clear up consisted in the intergranular brittleness of ordered alloys; this brittleness has been considerably reduced with appropriate conditions of elaboration and transformation. II) The studies upon the Young's modulus are in connection with iron-aluminium alloys; transformation temperatures are well shown up. The formation of covalent bonds on and after 25 atoms per cent show the highest values of the modulus. III) The analysis of variations of the flow stress according to the temperature show some connection with ordered structures, the existence of antiphase domains and the existence of sur-structure dislocations. IV) In the ordered Fe Al domain the kinetics of the Portevin-le-Chatelier effect could be explained by a mechanism of diffusion of vacancies. The role they play has been specified by the influence they exert upon the dislocations; this has led us to the inhomogeneous Rudman order; this inhomogeneous order could explain the shape of the traction curves. (author) [fr

Impact properties of aluminium - glass fiber reinforced plastics sandwich panels

Directory of Open Access Journals (Sweden)

Mathivanan Periasamy

2012-06-01

Full Text Available Aluminium - glass fiber reinforced plastics (GFRP sandwich panels are hybrid laminates consisting of GFRP bonded with thin aluminum sheets on either side. Such sandwich materials are increasingly used in airplane and automobile structures. Laminates with varying aluminium thickness fractions, fiber volume fractions and orientation in the layers of GFRP were fabricated by hand lay up method and evaluated for their impact performance by conducting drop weight tests under low velocity impacts. The impact energy required for initiating a crack in the outer aluminium layer as well as the energy required for perforation was recorded. The impact load-time history was also recorded to understand the failure behavior. The damage depth and the damage area were measured to evaluate the impact resistance. Optical photography and scanning electron micrographs were taken to visualize the crack and the damage zone. The bidirectional cross-ply hybrid laminate (CPHL has been found to exhibit better impact performance and damage resistance than the unidirectional hybrid laminate (UDHL. Increase in aluminium thickness fraction (Al tf and fiber volume fraction (Vf resulted in an increase in the impact energy required for cracking and perforation. On an overall basis, the sandwich panels exhibited better impact performance than the monolithic aluminium.

Photodynamic effect of aluminium and zinc tetrasulfophthalocyanines on melanoma cancer cells

CSIR Research Space (South Africa)

Maduray, K

2010-06-01

Full Text Available Aluminium and zinc tetrasulfophthalocyanines were activated with a 672nm wavelength laser to investigate the photodynamic effects on melanoma cancer, dermal fibroblast and epidermal keratinocyte cells. Aluminium tetrasulfophthalocyanine was more...

Numerical/experimental research on welded joints in aluminium truss girders

NARCIS (Netherlands)

van Hove, B.W.E.M.; Soetens, F.; Mazzolani, F.M.; Bellucci, F.; Faggiano, B.; Squillace, A.

2016-01-01

Welded joints in a 30 meter span aluminium truss girder were investigated numerically and experimentally. Since aluminium design rules for welded K-and N-joints in CHS truss girders were lacking the joints were checked using steel design rules. Calculations showed that the N-joints were governing

Numerical modelling of closed-cell aluminium foam under dynamic loading

Science.gov (United States)

Hazell, Paul; Kader, M. A.; Islam, M. A.; Escobedo, J. P.; Saadatfar, M.

2015-06-01

Closed-cell aluminium foams are extensively used in aerospace and automobile industries. The understanding of their behaviour under impact loading conditions is extremely important since impact problems are directly related to design of these engineering structures. This research investigates the response of a closed-cell aluminium foam (CYMAT) subjected to dynamic loading using the finite element software ABAQUS/explicit. The aim of this research is to numerically investigate the material and structural properties of closed-cell aluminium foam under impact loading conditions with interest in shock propagation and its effects on cell wall deformation. A μ-CT based 3D foam geometry is developed to simulate the local cell collapse behaviours. A number of numerical techniques are applied for modelling the crush behaviour of aluminium foam to obtain the more accurate results. The simulation results are compared with experimental data. Comparison of the results shows a good correlation between the experimental results and numerical predictions.

"INHIBITORY EFFECT OF ALUMINIUM ON KCL AND PHENYLEPHRINE INDUCED CONTRACTION IN ISOLATED RAT AORTA"

Directory of Open Access Journals (Sweden)

T. Mashhoodi

2004-10-01

Full Text Available It has been shown in some investigations that cardiovascular events are the main causes of death in hemodialysis patients. The exact etiology is unknown but some of the articles have reported a relation between aluminium ions in the dialysis solution and cardiovascular disorders. To determine the probable effect of aluminium on vasculature function, in vitro effects of aluminium ion on vasoconstriction induced by KCl (30 mM or phenylephrine (10 µM were investigated using isolated rat aorta. AlCl3 (1-4 mM decreased both KCl and phenylephrine induced contractions in a dose dependent manner (P<0.01. Complete inhibition of the contractions occurred using the higher doses of aluminium. Results of this study suggest that because of inhibitory effects of aluminium on vascular contractions, the probable cardiovascular dysfunction must be considered in aluminium intoxication.

Thermodynamic properties of uranium in gallium–aluminium based alloys

International Nuclear Information System (INIS)

Volkovich, V.A.; Maltsev, D.S.; Yamshchikov, L.F.; Chukin, A.V.; Smolenski, V.V.; Novoselova, A.V.; Osipenko, A.G.

2015-01-01

Activity, activity coefficients and solubility of uranium was determined in gallium-aluminium alloys containing 1.6 (eutectic), 5 and 20 wt.% aluminium. Additionally, activity of uranium was determined in aluminium and Ga–Al alloys containing 0.014–20 wt.% Al. Experiments were performed up to 1073 K. Intermetallic compounds formed in the alloys were characterized by X-ray diffraction. Partial and excess thermodynamic functions of U in the studied alloys were calculated. - Highlights: • Thermodynamics of uranium is determined in Ga–Al alloys of various compositions. • Uranium in the mixed alloys interacts with both components, Ga and Al. • Interaction of U with Al increases with decreasing temperature. • Activity and solubility of uranium depend on Al content in Ga–Al alloys.

Thermodynamic properties of uranium in gallium–aluminium based alloys

Energy Technology Data Exchange (ETDEWEB)

Volkovich, V.A., E-mail: v.a.volkovich@urfu.ru [Department of Rare Metals and Nanomaterials, Institute of Physics and Technology, Ural Federal University, Ekaterinburg, 620002 (Russian Federation); Maltsev, D.S.; Yamshchikov, L.F. [Department of Rare Metals and Nanomaterials, Institute of Physics and Technology, Ural Federal University, Ekaterinburg, 620002 (Russian Federation); Chukin, A.V. [Department of Theoretical Physics and Applied Mathematics, Institute of Physics and Technology, Ural Federal University, Ekaterinburg, 620002 (Russian Federation); Smolenski, V.V.; Novoselova, A.V. [Institute of High-Temperature Electrochemistry UD RAS, Ekaterinburg, 620137 (Russian Federation); Osipenko, A.G. [JSC “State Scientific Centre - Research Institute of Atomic Reactors”, Dimitrovgrad, 433510 (Russian Federation)

2015-10-15

Activity, activity coefficients and solubility of uranium was determined in gallium-aluminium alloys containing 1.6 (eutectic), 5 and 20 wt.% aluminium. Additionally, activity of uranium was determined in aluminium and Ga–Al alloys containing 0.014–20 wt.% Al. Experiments were performed up to 1073 K. Intermetallic compounds formed in the alloys were characterized by X-ray diffraction. Partial and excess thermodynamic functions of U in the studied alloys were calculated. - Highlights: • Thermodynamics of uranium is determined in Ga–Al alloys of various compositions. • Uranium in the mixed alloys interacts with both components, Ga and Al. • Interaction of U with Al increases with decreasing temperature. • Activity and solubility of uranium depend on Al content in Ga–Al alloys.

Natural gas anodes for aluminium electrolysis in molten fluorides.

Science.gov (United States)

Haarberg, Geir Martin; Khalaghi, Babak; Mokkelbost, Tommy

2016-08-15

Industrial primary production of aluminium has been developed and improved over more than 100 years. The molten salt electrolysis process is still suffering from low energy efficiency and considerable emissions of greenhouse gases (CO2 and PFC). A new concept has been suggested where methane is supplied through the anode so that the CO2 emissions may be reduced significantly, the PFC emissions may be eliminated and the energy consumption may decrease significantly. Porous carbon anodes made from different graphite grades were studied in controlled laboratory experiments. The anode potential, the anode carbon consumption and the level of HF gas above the electrolyte were measured during electrolysis. In some cases it was found that the methane oxidation was effectively participating in the anode process.

Comparison of the x-ray attenuation properties of breast calcifications, aluminium, hydroxyapatite and calcium oxalate.

Science.gov (United States)

Warren, L M; Mackenzie, A; Dance, D R; Young, K C

2013-04-07

Aluminium is often used as a substitute material for calcifications in phantom measurements in mammography. Additionally, calcium oxalate, hydroxyapatite and aluminium are used in simulation studies. This assumes that these materials have similar attenuation properties to calcification, and this assumption is examined in this work. Sliced mastectomy samples containing calcification were imaged at ×5 magnification using a digital specimen cabinet. Images of the individual calcifications were extracted, and the diameter and contrast of each calculated. The thicknesses of aluminium required to achieve the same contrast as each calcification when imaged under the same conditions were calculated using measurements of the contrast of aluminium foils. As hydroxyapatite and calcium oxalate are also used to simulate calcifications, the equivalent aluminium thicknesses of these materials were also calculated using tabulated attenuation coefficients. On average the equivalent aluminium thickness was 0.85 times the calcification diameter. For calcium oxalate and hydroxyapatite, the equivalent aluminium thicknesses were 1.01 and 2.19 times the thickness of these materials respectively. Aluminium and calcium oxalate are suitable substitute materials for calcifications. Hydroxyapatite is much more attenuating than the calcifications and aluminium. Using solid hydroxyapatite as a substitute for calcification of the same size would lead to excessive contrast in the mammographic image.

Different Approach to the Aluminium Oxide Topography Characterisation

International Nuclear Information System (INIS)

Poljacek, Sanja Mahovic; Gojo, Miroslav; Raos, Pero; Stoic, Antun

2007-01-01

Different surface topographic techniques are being widely used for quantitative measurements of typical industrial aluminium oxide surfaces. In this research, specific surface of aluminium oxide layer on the offset printing plate has been investigated by using measuring methods which have previously not been used for characterisation of such surfaces. By using two contact instruments and non-contact laser profilometer (LPM) 2D and 3D roughness parameters have been defined. SEM micrographs of the samples were made. Results have shown that aluminium oxide surfaces with the same average roughness value (Ra) and mean roughness depth (Rz) typically used in the printing plate surface characterisation, have dramatically different surface topographies. According to the type of instrument specific roughness parameters should be used for defining the printing plate surfaces. New surface roughness parameters were defined in order to insure detailed characterisation of the printing plates in graphic reproduction process

Quantitative electron probe microanalysis of borides in aluminium

International Nuclear Information System (INIS)

Karduck, P.; Schuerhoff, H.J.; Burchard, W.G.

1983-01-01

A procedure for the quantitative analysis of borides in aluminium was introduced. For this purpose the optimal apparative boundary conditions for the EPMA of boron were worked out. With these conditions a satisfactory peak to background ratio of 57 could be achieved for B-Kα-radiation. By application of this method the following conclusion should be drawn concerning the kind of nuclei during grain refinement of aluminium with titanium and boron: For grain refinement of aluminium with titanium and boron in the hypoperitectic region of the binary system Al-Ti TiB 2 -particles in clusters provide the high efficiency of refinement. This entails that the TiB 2 -particles already present in the master alloy remain inert in the melt. Hence, the good efficiency of refinement in this region cannot be attributed to the presence of particles like Al 3 Ti, AlB 2 or (Al, Ti) B 2 . (Author)

Aluminium - Cobalt-Pillared Clay for Dye Filtration Membrane

Science.gov (United States)

Darmawan, A.; Widiarsih

2018-04-01

The manufacture of membrane support from cobalt aluminium pillared clay has been conducted. This research was conducted by mixing a clay suspension with pillared solution prepared from the mixture of Co(NO3)2.6H2O and AlCl3.6H2O. The molar ratio between Al and Co was 75:25 and the ratio of [OH-]/[metal] was 2. The clay suspension was stirred for 24 hours at room temperature, filtered and dried. The dried clay was then calcined at 200°C, 300°C and 400°C with a ramp rate of 2°C/min. Aluminium-cobalt-pillared clay was then characterized by XRD and GSA and moulded become a membrane support for subsequent tests on dye filtration. The XRD analysis showed that basal spacing (d 001) value of aluminium cobalt was 19.49 Å, which was higher than the natural clay of 15.08Å however, the basal spacing decreased with increasing calcination temperature. The result of the GSA analysis showed that the pore diameter of the aluminium cobalt pillared clay membrane was almost the same as that of natural clay that were 34.5Å and 34.2Å, respectively. Nevertheless, the pillared clay has a more uniform pore size distribution. The results of methylene blue filtration measurements demonstrated that the membrane filter support could well which shown by a clear filtrate at all concentrations tested. The value of rejection and flux decreased with the increasing concentration of methylene blue. The values of dye rejection and water flux reached 99.89% and 5. 80 x 10-6 kg min-1, respectively but they decreased with increasing concentration of methylene blue. The results of this study indicates that the aluminium-pillared clay cobalt could be used as membrane materials especially for ultrafiltration.

Combined Corrosion and Wear of Aluminium Alloy 7075-T6

NARCIS (Netherlands)

Liu, Y.; Mol, J.M.C.; Janssen, G.C.A.M.

2016-01-01

The aluminium alloy 7075-T6 is widely used in engineering. In some applications, like slurry transport, corrosion and abrasion occur simultaneously, resulting in early material failure. In the present work, we investigated the combined effect of corrosion and wear on the aluminium alloy 7075-T6. We

Grain Refinement of Commercial EC Grade 1070 Aluminium Alloy for Electrical Application

OpenAIRE

Hassanabadi, Massoud

2015-01-01

The aluminium alloys for electrical conductivity applications are generally not grain refinedsince the addition of grain refiners drops the electrical conductivity by introducing impuritiesinto the melt. Non-grain refined aluminium may lead to bar fracture and cracks during themetalworking process. The present study focuses to find an optimum balance between the grain refiner addition andthe electrical conductivity of commercial EC grade 1070 aluminium alloy for electricalapplication. In orde...

Development of microstructure during sintering and aluminium exposure of titanium diboride ceramics

Energy Technology Data Exchange (ETDEWEB)

Pettersen, Gunnar

1997-12-31

In the production of aluminium, much less energy need be consumed if an inert, wetted cathode is present in the electrolysis cell. Titanium diboride, TiB{sub 2}, is easily wetted and does not readily dissolve in liquid aluminium, but it degrades, probably because aluminium penetrates into it during electrolysis. This degradation is linked to impurities present in the TiB{sub 2} after sintering. This thesis studies the sintering process and how aluminium penetrates into the material. High-purity, high-density TiB{sub 2} compacts were made by hot pressing at 50 MPa in an argon atmosphere at 1790-1960 {sup o}C. Samples were made with different impurity additions. These samples were exposed to liquid aluminium at 980 {sup o}C for 24 hours. All samples were penetrated, but the amount and appearance depended on the sintering aid used. Unlike the other samples, pure TiB{sub 2} was easily penetrated by metallic aluminium because of the open porosity and microcracks of this material. Grain boundary penetration was common among the samples. Differences in penetration behaviour between grain boundaries are probably due to differences in grain boundary energy. But no relation to segregants or boundary misorientation was found. The orientation of grain boundary planes and de-wetting of thin films upon cooling may explain the observed microstructure development. The samples sintered with Ti addition suffered extensive penetration despite their high densities. The grain boundaries of these samples became faceted and contained thicker films of metallic aluminium, presumably because of increased solubility due to iron segregations. All secondary phases present in the grain junctions after sintering, except from the B{sub 4}C phase, reacted with the penetrated aluminium. This did not cause swelling and cracking, as has been suggested by other authors. 101 refs., 48 figs., 7 tabs.

Effect of Microbial inoculation in combating the aluminium toxicity effect on growth of Zea mays.

Science.gov (United States)

Arora, P; Singh, G; Tiwari, A

2017-07-31

The present study is aimed at improving the aluminium tolerance in maize crop employing the potential of microbial inoculants in conferring resistance to these toxicities via production of certain chelating compounds like siderophores, exopolysachharides and organic acids. Acid soils have now-a-days become one of the key factors for limiting growth of many agriculturally important crops. Aluminium  is one of the major elements present in acid soils and is mainly responsible for toxicity in the soil. This aluminium is rapidly soluble in soil water and hence absorbed by plant roots under conditions where soil pH is below 5. This toxicity leads to severe root growth inhibition, thereby limiting the production of maize crops. It was observed that use of microbial inoculums can be helpful in elimination of these toxic compounds and prevent the inhibition of root growth . It was found that the soils contaminated with aluminium toxicity decreased the root length of maize plant significantly by 65% but Bacillus and Burkholderia inoculation increased this root length significantly by 1.4- folds and 2- folds respectively thereby combating the effect of aluminium toxicity. Aluminium concentration was found maximum in roots of plants which were grown under aluminium stress condition. But this aluminium accumulation decreased ̴ 2-folds when Burkholderia was used as seed inoculants under aluminium stress conditions. Also, at 60mM aluminium accumulation, phosphorus solubilisation in roots was found to be increased upto 30% on Burkholderia inoculation. However, Bacillus inoculation didn't show any significant difference in either of the case. Thus, the inoculation of seeds with Burkholderia isolates could prove to be a boon in sequestering aluminium toxicity in Zea mays.

Modeling and evaluation of urban pollution events of atmospheric heavy metals from a large Cu-smelter.

Science.gov (United States)

Chen, Bing; Stein, Ariel F; Castell, Nuria; Gonzalez-Castanedo, Yolanda; Sanchez de la Campa, A M; de la Rosa, J D

2016-01-01

Metal smelting and processing are highly polluting activities that have a strong influence on the levels of heavy metals in air, soil, and crops. We employ an atmospheric transport and dispersion model to predict the pollution levels originated from the second largest Cu-smelter in Europe. The model predicts that the concentrations of copper (Cu), zinc (Zn), and arsenic (As) in an urban area close to the Cu-smelter can reach 170, 70, and 30 ng m−3, respectively. The model captures all the observed urban pollution events, but the magnitude of the elemental concentrations is predicted to be lower than that of the observed values; ~300, ~500, and ~100 ng m−3 for Cu, Zn, and As, respectively. The comparison between model and observations showed an average correlation coefficient of 0.62 ± 0.13. The simulation shows that the transport of heavy metals reaches a peak in the afternoon over the urban area. The under-prediction in the peak is explained by the simulated stronger winds compared with monitoring data. The stronger simulated winds enhance the transport and dispersion of heavy metals to the regional area, diminishing the impact of pollution events in the urban area. This model, driven by high resolution meteorology (2 km in horizontal), predicts the hourly-interval evolutions of atmospheric heavy metal pollutions in the close by urban area of industrial hotspot.

Risk minimisation of FGD gypsum leachates by incorporation of aluminium sulphate

Energy Technology Data Exchange (ETDEWEB)

Alvarez-Ayuso, E. [Department of Environmental Geology, Institute of Earth Sciences ' Jaume Almera' (CSIC), C/ Lluis Sole i Sabaris, s/n, 08028 Barcelona (Spain); Department of Environmental Geochemistry, IRNASA, CSIC, Apto. 257, 37071 Salamanca (Spain)], E-mail: ealvarez@ija.csic.es; Querol, X. [Department of Environmental Geology, Institute of Earth Sciences ' Jaume Almera' (CSIC), C/ Lluis Sole i Sabaris, s/n, 08028 Barcelona (Spain); Ballesteros, J.C.; Gimenez, A. [Endesa Generacion, S.A., C/ Ribera de Loira, 60, 28042 Madrid (Spain)

2008-11-15

The incorporation of aluminium sulphate to (flue gas desulphurisation) FGD gypsum before its disposal was investigated as a way to minimise the risk supposed by the high fluoride content of its leachates. Using a bath method the kinetic and equilibrium processes of fluoride removal by aluminium sulphate were studied at fluoride/aluminium molar concentration (F/Al) ratios in the range 1.75 10{sup -2}-1.75 under the pH conditions (about 6.5) of FGD gypsum leachates. It was found that fluoride removal was a very fast process at any of the (F/Al) ratios subject of study, with equilibrium attained within the first 15 min of interaction. High decreases in solution fluoride concentrations (50-80%) were found at the equilibrium state. The use of aluminium sulphate in the stabilization of FGD gypsum proved to greatly decrease its fluoride leachable content (in the range 20-90% for aluminium sulphate doses of 0.1-5%, as determined by the European standard EN 12457-4). Such fluoride leaching minimisation assures the characterization of this by-product as a waste acceptable at landfills for non-hazardous wastes according to the Council Decision 2003/33/EC on waste disposal. Furthermore, as derived from column leaching studies, the proposed stabilization system showed to be highly effective in simulated conditions of disposal, displaying fluoride leaching reduction values about 55 and 80% for aluminium sulphate added amounts of 1 and 2%, respectively.

Aluminium Foam and Magnesium Compound Casting Produced by High-Pressure Die Casting

Directory of Open Access Journals (Sweden)

Iban Vicario

2016-01-01

Full Text Available Nowadays, fuel consumption and carbon dioxide emissions are two of the main focal points in vehicle design, promoting the reduction in the weight of vehicles by using lighter materials. The aim of the work is to evaluate the influence of different aluminium foams and injection parameters in order to obtain compound castings with a compromise between the obtained properties and weight by high-pressure die cast (HPDC using aluminium foams as cores into a magnesium cast part. To evaluate the influence of the different aluminium foams and injection parameters on the final casting products quality, the type and density of the aluminium foam, metal temperature, plunger speed, and multiplication pressure have been varied within a range of suitable values. The obtained compound HPDC castings have been studied by performing visual and RX inspections, obtaining sound composite castings with aluminium foam cores. The presence of an external continuous layer on the foam surface and the correct placement of the foam to support injection conditions permit obtaining good quality parts. A HPDC processed magnesium-aluminium foam composite has been developed for a bicycle application obtaining a suitable combination of mechanical properties and, especially, a reduced weight in the demonstration part.

Adsorption of lithium ion to amorphous hydrous aluminium oxide

International Nuclear Information System (INIS)

Wada, Hideo; Kitamura, Takao; Fujii, Ayako; Katoh, Shunsaku

1982-01-01

Adsorption process of lithium ion to amorphous hydrous aluminium oxide (a-HAO) was investigated by pH titration method with lithium chloride-lithium hydroxide mixed solution and X-ray diffraction analysis of a-HAO after pH titration. In the pH titration, the addition of hydroxide ion in amount from 0 to 4.0 mmol.g -1 gave no change to the pH of the solution and caused adsorption of lithium ion equivalent in amount to added hydroxide ion. X-ray diffraction analysis showed the formation of lithium hydrogenaluminate LiH (AlO 2 ) 2 .5H 2 O (LHA) in the a-HAO after pH titration. These results showed that adsorption of lithium ion by a-HAO was related to a reaction which consumed hydroxide ion and formed LHA. In order to elucidate detail process of the reaction, changes of pH, aluminium concentration and lithium concentration of the solution, respectively with time, were determined. The pH of the solution decreased in two stages. At the first stage of the pH decrease, the aluminium concentration increased whereas the lithium concentration did not change. At the second stage, the lithium concentration decreased together with the decrease of the aluminium concentration. It was inferred that adsorption of lithium ion proceeded through dissolution of a-HAO and precipitation of LHA. Theoretical adsorption capacity calculated from the above formula for LHA and aluminium content in a-HAO was 4.7 mmol.g -1 and agreed fairly well with observed value 4.0 mmol.g -1 . (author)

Coprecipitation of aluminium with hydroxides of tetra-, penta- and hexavalent actinides

International Nuclear Information System (INIS)

Yusov, A.B.; Budantseva, N.A.; Anan'ev, A.V.; Fedoseev, A.M.

2000-01-01

By the methods of IR spectroscopy and powder x-ray diffractometry precipitates formed in alkaline medium by actinide (4, 5, 6) in the presence of aluminium are studied. It is shown that in studied conditions formation of actinide aluminates not occurs. In the same time in the process of precipitation interaction of aluminium hydroxocomplexes with U(6) and Th(4) ions probably takes place. Hypothesis is expressed that possibility of aluminium hydroxocomplexes interaction with actinides in different oxidation state is depended on peculiarities of hydrolytic behaviour of the lasts [ru

A study on the role of diboride in the heterogeneous nucleation of aluminium

International Nuclear Information System (INIS)

Suarez, O. M.

2004-01-01

The intangible role of titanium and aluminium diboride in the nucleation of aluminium was re-examined. Two different techniques, complemented with scanning electron microscopy, allowed determining the stability of the diboride in the presence of titanium tri aluminides and liquid aluminium phases. Through rapid scintillated quenching the high temperature diboride were retained and studied. Then, in a diffusion couple, the reactivity of such diboride was tested in contact with pure titanium tri aluminide. It is proposed that a ternary diboride acts as the main catalytic particle in the crystallization of aluminium alloys with refined grains. (Author) 27 refs

Integrating science and business models of sustainability for environmentally-challenging industries such as secondary lead smelters: a systematic review and analysis of findings.

Science.gov (United States)

Genaidy, A M; Sequeira, R; Tolaymat, T; Kohler, J; Wallace, S; Rinder, M

2010-09-01

Secondary lead smelters (SLS) represent an environmentally-challenging industry as they deal with toxic substances posing potential threats to both human and environmental health, consequently, they operate under strict government regulations. Such challenges have resulted in the significant reduction of SLS plants in the last three decades. In addition, the domestic recycling of lead has been on a steep decline in the past 10 years as the amount of lead recovered has remained virtually unchanged while consumption has increased. Therefore, one may wonder whether sustainable development can be achieved among SLS. The primary objective of this study was to determine whether a roadmap for sustainable development can be established for SLS. The following aims were established in support of the study objective: (1) to conduct a systematic review and an analysis of models of sustainable systems with a particular emphasis on SLS; (2) to document the challenges for the U.S. secondary lead smelting industry; and (3) to explore practices and concepts which act as vehicles for SLS on the road to sustainable development. An evidence-based methodology was adopted to achieve the study objective. A comprehensive electronic search was conducted to implement the aforementioned specific aims. Inclusion criteria were established to filter out irrelevant scientific papers and reports. The relevant articles were closely scrutinized and appraised to extract the required information and data for the possible development of a sustainable roadmap. The search process yielded a number of research articles which were utilized in the systematic review. Two types of models emerged: management/business and science/mathematical models. Although the management/business models explored actions to achieve sustainable growth in the industrial enterprise, science/mathematical models attempted to explain the sustainable behaviors and properties aiming at predominantly ecosystem management. As such

Study of the electronic structure of pure aluminium, aluminium oxide and nitride by spectroscopy of electrons excited under electronic and photonic bombardment (X and UV)

International Nuclear Information System (INIS)

Gautier-Soyer, Martine

1985-01-01

This research thesis reports the use of electron spectroscopy with electrons excited under electronic or photonic (X or UV) bombardment for the study of electronic state density of aluminium, aluminium oxide (Al 2 O 3 ) and aluminium nitride (AlN). The objective is to get an insight into phenomena related to technological problems of adherence, wear, lubrication, corrosion or breakdown met in metals, insulators and semiconductors. The author highlighted the presence of occupied surface states on Al(111) and Al(100), and electronic levels localised in the forbidden band of Al 2 O 3 and AlN, induced by structural defects which promote surface reactivity [fr

The environmental rules of economic development: Governing air pollution from smelters in Chuquicamata and La Oroya

OpenAIRE

Orihuela, José Carlos

2015-01-01

Why and how do societies transform the environmental rules of economic development, or fail to do so? This article compares the experiences of Chile and Peru in the regulation of smelting activities between 1990 and 2010. Air pollution from smelters in  Chuquicamata  and  La Oroya, each emblematic of the two countries’ mining industries, did not give rise to nationally destabilising protest. Nevertheless, despite the absence of pressing discontent with pollution, the environmental rules for m...

Effect of aluminium particles on mechanical and morphological properties of epoxy nanocomposites

Directory of Open Access Journals (Sweden)

Bello Sefiu A.

2017-01-01

Full Text Available Bumper is a front or rear part of automobiles. It is designed and shaped to be impact absorbing and protecting automobiles from damage in low impact collisions. Initially, they were made from heavy steels, increasing the weight of automobiles and fuel consumption. Also, high impacts of steel bumpers on pedestrians during accidental collision cause fatalities and or disabilities. An effort to enhance fuel efficiency, safety, freedom of design and shape detailing, heavy alloys for automobile applications are now being replaced with polymeric composites. Aluminium micro particles and nanoparticles were prepared from aluminium cans through sand casting, lathe machine spinning, and ball milling techniques. Both types of aluminium particles were incorporated into a mixture of diglycidyl ether of bisphenol A (DGEBA, epoxy resin cured with amine base hardener (ABH. Phases of the epoxy polymer and composites were identified using Xray Diffraction (XRD. Spatial arrangement of the phases within the matrix and their elemental composition were examined using Scanning Electron Microscope with attached energy dispersive X-ray spectroscopy (SEM/EDX. Tensile, impact and micro hardness tests were conducted on the prepared epoxy/aluminium composites. Results of the XRD showed the presence of aluminium compounds/phases due to chemical reactions between aluminium particles and DGEBA/ABH system. SEM confirmed a homogeneous distribution of the phases within the epoxy matrix, and that there is a strong adhesion between the epoxy matrix and aluminium particles. Correlation between the mechanical properties of the prepared nanocomposite and the procured bumper materials exhibited a fair suitability of the prepared nanocomposites for automobile applications.

Comparative performance of aluminium copper and iron solar stills

International Nuclear Information System (INIS)

Dioha, I.J.; Nwagbo, E.E.; Gulma, N.A.

1990-12-01

Three different metal sheets have been used in the fabrication of three different single sloping solar stills of the same surface geometry. The metals were galvanized iron, aluminium and copper. This paper presents the performance of the different stills operating under the same environmental conditions. The observed distillate yields was greatest for copper, then aluminium and lastly, iron still. The differences in the yields is attributed to the differences in the thermal conductivities of the metals. The equivalent local costs for the fabrication of the copper, aluminium and iron stills are respectively $160, $95 and $60. Taking the long run costs into consideration, the copper still is preferred because of its availability, durability, weldability and relatively higher conductivity of 380Wm -1 K -1 value. (author). 9 refs, 2 figs, 2 tabs

Aluminium and Alzheimer's disease: the science that describes the link

National Research Council Canada - National Science Library

Exley, Christopher

2001-01-01

... that has been encircled is the gene for the amyloid precursor protein. (Thanks to Walter Lukiw for supplying this information.) Aluminium and Alzheimer's Disease: The Science that Describes the LinkAluminium and Alzheimer's Disease The Science that Describes the Link Edited by Christopher Exley Birchall Centre for Inorganic Chemistry and Materials Scienc...

Activation Analysis of Aluminium

Energy Technology Data Exchange (ETDEWEB)

Brune, Dag

1961-01-15

An analysis of pure aluminium alloyed with magnesium was per- formed by means of gamma spectrometry , Chemical separations were not employed. The isotopes to be determined were obtained in conditions of optimum activity by suitably choosing the time of irradiation and decay. The following elements were detected and measured quantitatively: Iron, zinc, copper, gallium, manganese, chromium, scandium and hafnium.

Study of the secondary electron energy spectrum of clean aluminium modification during oxygen adsorption, hydrogen adsorption or carbon segregation

International Nuclear Information System (INIS)

Pellerin, Francois

1981-01-01

The first part of this work is a review of both theoretical and experimental aspects of the fine structure appearing in the Secondary Electron Spectrum (SES) and in the electron energy loss spectrum. In the second part, we report the results of a study of the SES and ELS spectra of clean and gas covered aluminium. The use of very low primary electron energies (E p ≤ 30 eV) enables the detection of previously unobserved peaks in the ELS spectra of clean and oxygen covered aluminium. They are attributed to single electron excitations. Furthermore, a very large peak appears in the SES spectrum during oxygen or carbon adsorption on aluminium. It is interpreted in terms of interaction of the background electrons with the valence electrons of the surface. Molecular hydrogen adsorption is observed on Ta, Pt, Al 2 O 3 , Si. It is responsible for an ELS peak located 13 eV below the elastic peak. Furthermore, on silicon, the chemisorbed hydrogen form can be distinguished from the molecular form with the help of ELS. Finally, some examples are given of the application of these results to surface imaging. (author) [fr

Diagnostics of ytterbium/aluminium laser plasmas

International Nuclear Information System (INIS)

Bailey, J.; Lee, R.W.; Landen, O.L.; Kilkenny, J.D.; Lewis, C.L.; Busquet, M.

1986-11-01

Microdot spectroscopy was used to study the x-ray emission from laser-produced plasmas consisting of 10% ytterbium, 90% aluminium. Spectra were recorded with a space-resolving flat crystal (PET) mini-spectrometer in the 4.0-8.0 A range. The Janus research laser at LLNL irradiated the targets with green (0.53 μm) light in a 1 nsec pulse. The power density was varied between 4x10 13 and 3x10 14 W/cm 2 . The plasma electron density and temperature were determined from the aluminium XI, XII and XIII line emission. By examining correlations between changes in the plasma conditions with changes in the ytterbium spectra, we will determine the potential for using ytterbium line emission as a plasma diagnostic

Corrosion of research reactor aluminium clad spent fuel in water

International Nuclear Information System (INIS)

2009-12-01

A large variety of research reactor spent fuel with different fuel meats, different geometries and different enrichments in 235 U are presently stored underwater in basins located around the world. More than 90% of these fuels are clad in aluminium or aluminium based alloys that are notoriously susceptible to corrosion in water of less than optimum quality. Some fuel is stored in the reactor pools themselves, some in auxiliary pools (or basins) close to the reactor and some stored at away-from-reactor pools. Since the early 1990s, when corrosion induced degradation of the fuel cladding was observed in many of the pools, corrosion of research reactor aluminium clad spent nuclear fuel stored in light water filled basins has become a major concern, and programmes were implemented at the sites to improve fuel storage conditions. The IAEA has since then established a number of programmatic activities to address corrosion of research reactor aluminium clad spent nuclear fuel in water. Of special relevance was the Coordinated Research Project (CRP) on Corrosion of Research Reactor Aluminium Clad Spent Fuel in Water (Phase I) initiated in 1996, whose results were published in IAEA Technical Reports Series No. 418. At the end of this CRP it was considered necessary that a continuation of the CRP should concentrate on fuel storage basins that had demonstrated significant corrosion problems and would therefore provide additional insight into the fundamentals of localized corrosion of aluminium. As a consequence, the IAEA started a new CRP entitled Corrosion of Research Reactor Aluminium Clad Spent Fuel in Water (Phase II), to carry out more comprehensive research in some specific areas of corrosion of aluminium clad spent nuclear fuel in water. In addition to this CRP, one of the activities under IAEA's Technical Cooperation Regional Project for Latin America Management of Spent Fuel from Research Reactors (2001-2006) was corrosion monitoring and surveillance of research

Study of super-conductors in the aluminium-magnesium system; Etude des supraconducteurs du systeme aluminium-magnesium

Energy Technology Data Exchange (ETDEWEB)

Bonnin, B [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1965-05-01

The author has designed and built an apparatus for the measurement of the magnetization of superconducting alloys by the classical method of extraction. Its originality is due to the employment of a cryostat having two helium baths. The lowest temperature reached by pumping on the innermost helium bath using a primary pump combined with a BOOSTER pump is 0.75 deg. K. Temperatures are determined with a aid of Hartshorn bridge. With this apparatus, it has been possible to study the influence of extended defects on the irreversible behaviour of the magnetization of aluminium-magnesium alloys. It has been shown that the effect of these defects is important chiefly in the superconductors alloys of the second kind. The introduction of the extended defects was controlled by electron microscopy and by the measure of the residual resistivities. Finally, the author has measured for these alloys the critical fields Hc, Hc1, Hc2, the transition temperatures Tc and the coefficients of electronic specific heat {gamma}. (author) [French] L'auteur a realise un appareillage lui permettant de mesurer l'aimantation d'alliages supraconducteurs par la methode classique d'extraction. L'originalite du montage reside en la construction d'un cryostat a double bain d'helium. La temperature la plus basse atteinte en pompant sur le bain d'helium interieur a l'aide d'une pompe BOOSTER est de 0.75 deg. K. Les temperatures sont determinees a l'aide d'un pont de Hartshorn. C'est avec cet appareillage que l'auteur a pu etudier l'influence des defauts etendus sur le comportement irreversible de l'aimantation d'alliages d'aluminium-magnesium. Il a montre que l'influence de ces defauts est essentiellement sensible dans les alliages supraconducteurs de la deuxieme espece. L'introduction des defauts etendus a ete controlee par microscopie electronique et par mesure de resistivite residuelle. Enfin, pour tous ces alliages ont ete mesures: les champs critiques Hc, Hc1, Hc2, les temperatures critiques Tc

A note on the behind armour effects from perforated alumina/aluminium targets

OpenAIRE

Hazell, P. J.; Fellows, N. A.; Hetherington, J. G.

1998-01-01

A thin, ceramic-faced armour, separated from a thick metal block, has been subjected to high-velocity impact by a 6.35 mm diameter steel sphere. Experimental work was carried out which compared firings into ceramic-faced aluminium armour, separated from thick aluminium witness blocks, with firings into the thick aluminium blocks alone. The depth of penetration and the area of damage were measured and an estimated percentage weight saving due to the inclusion of the ceramic-f...

Corrosion behaviour of nanometre sized cerium oxide and titanium oxide incorporated aluminium in NaCl solution

International Nuclear Information System (INIS)

Ashraf, P. Muhamed; Edwin, Leela

2013-01-01

Highlights: ► Corrosion resistant aluminium incorporated with nano oxides of cerium and titanium. ► 0.2% nano CeO 2 and 0.05% nano TiO 2 showed increased corrosion resistance. ► Nano TiO 2 concentration influenced the optimum performance of the material. ► Comparison of Micro and nano CeO 2 and TiO 2 aluminium showed the latter is best. - Abstract: The study highlights the development of an aluminium matrix composite by incorporating mixture of nanometre sized cerium oxide and titanium oxide in pure aluminium and its corrosion resistance in marine environment. The mixed nanometre sized oxides incorporated aluminium exhibited improved microstructure and excellent corrosion resistance. Corrosion resistance depends on the concentration of nanometre sized titanium oxide. Electrochemical characteristics improved several folds in nanometre sized mixed oxides incorporated aluminium than micrometre sized oxides incorporated aluminium.

Purity and surface roughness of vacuum deposited aluminium films

Energy Technology Data Exchange (ETDEWEB)

Dhere, N G; Arsenio, T P [Instituto Militar de Engenharia, Rio de Janeiro (Brazil); Patnaik, B K [Pontificia Universidade Catolica do Rio de Janeiro (Brazil). Instituto de Fisica; Assuncao, F C.R.; de Souza, A M [Pontificia Universidade Catolica do Rio de Janeiro (Brazil). Departamento de Ciencia dos Materiais e Metalurgia

1975-04-01

The authors studied the purity, surface roughness and grain size of vacuum-deposited aluminium films, using an intermetallic crucible and a continuous feed of pure aluminium wire. The grain size and roughness were studied by electron difraction, X-ray diffraction and the scanning electron microscope. Purity was determined by X-ray fluorescence produced by proton bombardment in the Van de Graaff accelerator and by X-ray and optical emission spectrometry.

On the anodic aluminium oxide refractive index of nanoporous templates

International Nuclear Information System (INIS)

Hierro-Rodriguez, A; Rocha-Rodrigues, P; Araujo, J P; Valdés-Bango, F; Alameda, J M; Teixeira, J M; Jorge, P A S; Santos, J L; Guerreiro, A

2015-01-01

In the present study, we have determined the intrinsic refractive index of anodic aluminium oxide, which is originated by the formation of nanoporous alumina templates. Different templates have been fabricated by the conventional two-step anodization procedure in oxalic acid. Their porosities were modified by chemical wet etching allowing the tuning of their effective refractive indexes (air-filled nanopores  +  anodic aluminium oxide). By standard spectroscopic light transmission measurements, the effective refractive index for each different template was extracted in the VIS–NIR region. The determination of the intrinsic anodic aluminium oxide refractive index was performed by using the Maxwell–Garnett homogenization theory. The results are coincident for all the fabricated samples. The obtained refractive index (∼1.55) is quite lower (∼22%) than the commonly used Al 2 O 3 handbook value (∼1.75), showing that the amorphous nature of the anodic oxide structure strongly conditions its optical properties. This difference is critical for the correct design and modeling of optical plasmonic metamaterials based on anodic aluminium oxide nanoporous templates. (paper)

ADC3 YANG DIBUAT DENGAN PELEBURAN ULANG ALUMINIUM BEKAS SEBAGAI BAHAN PROPELER KAPAL KAYU

Directory of Open Access Journals (Sweden)

Suyanto Suyanto

2016-11-01

Full Text Available Saat ini pembuatan propeler aluminium pada industri kecil banyak memanfaatkan bahan dasar aluminium bekas. Namun produk yang dihasilkan belum memenuhi spesifikasi standar material. Penelitian dilakukan dengan menggunakan bahan dasar aluminium siku bekas dan aluminium kampas bekas. Variasi penambahan TiB sebagai grain refiner dilakukan pada saat peleburan. Perhitungan dengan simulasi Excel dilakukan untuk memperkirakan komposisi hasil pengecoran yang sesuai. Pengecoran ulang menghasilkan produk dengan tingkat porositas 3,3 % sampai 5,9 %. Penggunaan cetakan pasir ikut berperan dalam timbulnya porositas. Penambahan TiB sebanyak 0,5% ke ADC3 berpengaruh pada penurunan ukuran butir hingga 50%, peningkatan kekerasan hingga 23%, peningkatan kekuatan tarik hingga 11%, serta penurunan keuletan hingga 20%. Kata kunci: ADC3, pengecoran ulang aluminium, propeler.

A reliability based stress-life evaluation of aluminium-graphite particulate composites

International Nuclear Information System (INIS)

Achutha, M.V.; Sridhara, B.K.; Abdul Budan, D.

2008-01-01

Fatigue tests were conducted on sand cast aluminium-graphite composite specimens on Rotating Beam Fatigue Testing Machine with three different stress levels. Aluminium-graphite (LM 25-5% graphite) composite was processed by closed mould sand casting method. Three-stress level fatigue test program was planned for carrying out fatigue experiments. Three different stress levels selected for fatigue experiments were a fraction of ultimate tensile strength. Statistical design of fatigue experiments was carried out to determine the sample size at each stress level. Experimental results are presented in the form of stress-life (S-N) curves and reliability-stress-life (R-S-N) curves, which are helpful for designers. The S-N curve of the aluminium-graphite composite was compared with its matrix alloy LM 25. Comparison revealed that the fatigue behaviour of the aluminium-graphite composite is superior to that of the matrix alloy

Corrosion behaviour of zinc and aluminium in simulated nuclear accident environments

International Nuclear Information System (INIS)

Piippo, J.; Laitinen, T.; Sirkiae, P.

1997-02-01

The corrosion rates of zinc and aluminium were determined in simulated large pipe break and in severe accident cases. An in situ on fine measurement technique, which is based on the resistance measurement of sample wires, was used. In the large pipe break case the corrosion rates of zinc and aluminium were determined at pH 8 and pH 10 in deaerated and in aerated solutions. Tests were also performed in aerated 0.1 M borate buffer solution at pH 9.2. Temperature range was 130 deg C - 50 deg C. The corrosion of zinc appears to be relatively fast in neutral or mildly alkaline aerated water, while both high pH and deaeration tend to reduce the corrosion rates of zinc. The aeration and pH elevation decrease the corrosion rate of aluminium. The simulation of the severe accident case took place in the pH range 3-11 in chloride containing solutions at 50 deg C temperature. The corrosion rate of aluminium was lower than that of zinc, except for the solution with pH 11, in which the corrosion rate of aluminium was practically identical to that of zinc. Both metals corroded more rapidly in the presence of chlorides in acidic and alkalic conditions than in the absence of chlorides at neutral environment. The solubility of zinc and aluminium and the stability of the corrosion products were estimated using thermodynamical calculations. The experimental results and the thermodynamical calculations were in fair agreement. (8 refs.)

Development of solar selective absorber layers on aluminium. Final report; Entwicklung solarselektiver Absorberschichten auf Aluminium fuer Solarkollektoren. Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Hoenicke, D.; Moeller, T.; Schwarz, T.

1998-01-31

A new electrolytic process was developed to form solar selective layers on aluminium. In the developed process, both the formation of the alumina layer and the deposition of metals into the layer takes place in only one treatment step using a single electrolysis bath. The main step of the so called ISOC-method (impulse structured oxide ceramic) is the anodic oxidation of aluminium which was carried out by using a pulse technique at different voltages. During the anodic polarisation a thin alumina ceramic layer was formed, while the cathodic led to the metal deposition as copper and nickel. The conditions of the electrolysis were varied in order to estimate optimal parameters achieving solar selective layers with high selectivity. Furthermore, a scale-up of the lab scale apparatus to a mini plant was carried out. Finally, the corrosion resistance of the absorber layers was improved by the formation of a thin hydrophobic overlayer using a sol-gel treatment. (orig.) [Deutsch] Ein neuartiges Behandlungsverfahren zur Erzeugung von solarselektiven Absorberschichten auf Aluminium wurde entwickelt. Bei dieser elektrochemischen Behandlung wird in einem Einstufenprozess mit einem Elektrolyten durch eine Kombination von anodischer Oxidation und bipolarer Pulsbehandlung auf der Oberflaeche des Aluminiums eine impulsstrukturierte Oxidkeramik (ISOK) erzeugt. Dabei entsteht durch eine anodische Oxidation eine strukturierte Aluminiumoxidschicht. Bei der bipolaren Pulsbehandlung erfolgt dann eine Abscheidung der im ISOK-Elektrolyten befindlichen Metalle Cu und Ni auf oder in die Aluminiumoxidoberflaeche. Die ISOK-Behandlung wurde vom Labormassstab zu einem ISOK-Verfahren im Miniplant-Massstab entwickelt. Der Einfluss der elektrischen Parameter und der chemischen Zusammensetzung der ISOK-Elektrolyte wurde untersucht. Durch eine auf das ISOK-Verfahren abgestimmte Nachbehandlung, ein Tauchverfahren in einer Sol-Gel-Loesung, entsteht ein Schichtsystem mit hoher Solarselektivitaet

Friction conditions in the bearing area of an aluminium extrusion process

NARCIS (Netherlands)

Ma, X.; de Rooij, Matthias B.; Schipper, Dirk J.

2012-01-01

In aluminium extrusion processes, friction inside the bearing channel is important for controlling the surface quality of the extrusion products. The contact materials show a large hardness difference, one being hot aluminium, and the other being hardened tool steel. Further, the contact pressure is

Propolis Protection from Toxicity Caused by Aluminium Chloride in Male Rats

International Nuclear Information System (INIS)

Mangood, S.A.; Kamal, A.M.; Haggag, A.M.

2012-01-01

Propolis is a resinous natural hive product derived from plant exudate collected by honey bees and has been extensively used in folk medicine. The present study was undertaken to determine the effectiveness of propolis in alleviating the toxicity of aluminium chloride (AlCl 3 )on some hematological and biochemical parameters of male albino rats. Twenty four male albino rats were arranged into 4 equal groups; control group, aluminium group (34 mg AlCl 3 /kg/day), propolis group (100μg propolis/rat)and aluminium plus propolis group. Rats were orally administered their respective doses daily for 30 days. AlCl 3 caused significant decrease in hemoglobin (Hb), red blood cell count (RBC), hematocrit (Ht), total and differential leucocyte count (TLC) when compared to control. On the other hand, aluminium administration caused a significant increase in urea, uric acid, creatinin, bilirubin, the content of phosphorous, alanine aminotransferase (ALT) and asparate aminotransferase (AST) and significant decrease in total protein, albumin, globulin and calcium when compared to control. The administration of propolis alleviated the toxic effect of AlCl 3 in experimental rats. It could be concluded thal propolis my afford protection from toxicity caused by aluminium chloride in male albino rats

High-purity aluminium creep under high hydrostatic pressure

International Nuclear Information System (INIS)

Zajtsev, V.I.; Lyafer, E.I.; Tokij, V.V.

1977-01-01

The effect of the hydrostatic pressure on the rate of steady-state creep of high-purity aluminium was investigated. It is shown that the hydrostatic pressure inhibits the creep. The activation volume of the creep is independent of the direction in the range of (4.7-6.2) kg/mm 2 and of the pressure in the range of (1-7.8000) atm. It is concluded that self-diffusion does not control the creep of high-purity aluminium at room temperature in the investigated stress and pressure range

Toxicity of smelter slag-contaminated sediments from Upper Lake Roosevelt and associated metals to early life stage White Sturgeon (Acipenser transmontanus Richardson, 1836)

Science.gov (United States)

Little, E.E.; Calfee, R.D.; Linder, G.

2014-01-01

The toxicity of five smelter slag-contaminated sediments from the upper Columbia River and metals associated with those slags (cadmium, copper, zinc) was evaluated in 96-h exposures of White Sturgeon (Acipenser transmontanus Richardson, 1836) at 8 and 30 days post-hatch. Leachates prepared from slag-contaminated sediments were evaluated for toxicity. Leachates yielded a maximum aqueous copper concentration of 11.8 μg L−1 observed in sediment collected at Dead Man's Eddy (DME), the sampling site nearest the smelter. All leachates were nonlethal to sturgeon that were 8 day post-hatch (dph), but leachates from three of the five sediments were toxic to fish that were 30 dph, suggesting that the latter life stage is highly vulnerable to metals exposure. Fish maintained consistent and prolonged contact with sediments and did not avoid contaminated sediments when provided a choice between contaminated and uncontaminated sediments. White Sturgeon also failed to avoid aqueous copper (1.5–20 μg L−1). In water-only 96-h exposures of 35 dph sturgeon with the three metals, similar toxicity was observed during exposure to water spiked with copper alone and in combination with cadmium and zinc. Cadmium ranging from 3.2 to 41 μg L−1 or zinc ranging from 21 to 275 μg L−1 was not lethal, but induced adverse behavioral changes including a loss of equilibrium. These results suggest that metals associated with smelter slags may pose an increased exposure risk to early life stage sturgeon if fish occupy areas contaminated by slags.

Contradictory effect of chromate inhibitor on corrosive wear of aluminium alloy

International Nuclear Information System (INIS)

Pokhmurskii, V.I.; Zin, I.M.; Vynar, V.A.; Bily, L.M.

2011-01-01

Research highlights: → Corrosive wear of aluminium alloy in inhibited artificial acid rain was studied. → Tribometer with linear reciprocating ball-on-flat geometry was used.→ Corrosion potential, polarization current and friction coefficient were measured. → Chromate decreases corrosion of aluminium alloy under wear conditions. → Chromate in general accelerates corrosive wear of the alloy in acid rain. - Abstract: The corrosive wear of D16T aluminium alloy in artificial acid rain was studied. A special tribometer with the linear reciprocating ball-on-flat geometry was used. The setup allows to measure simultaneously an open circuit potential, to carry out potentiostatic and potentiodynamic polarization studies of the alloy corrosion and to record the friction coefficient. It was established that the addition of strontium chromate inhibitor to the working environment decreases an electrochemical corrosion of the aluminium alloy under wear conditions, but in general accelerates its destruction due to insufficient wear resistance of a formed surface film.

A study of aluminium-exposed fish using a scanning proton microprobe

Energy Technology Data Exchange (ETDEWEB)

Cholewa, M; Legge, G L.F. [Melbourne Univ., Parkville, VIC (Australia). School of Physics; Eeckhaoudt, S; Van Grieken, R [Universitaire Instelling Antwerpen, Antwerp (Belgium)

1994-12-31

A major problem has arisen in Europe with the depopulation of fresh water fish in lakes and streams collecting acid rain. The sensitivity to acidification is species specific and appears to be associated with metal levels. The Scanning Proton Microprobe (SPMP) at the Micro Analytical Research Centre of the University of Melbourne was used to study the subcellular distribution of aluminium and other elements in the gills of fish exposed to acidified water with elevated Al-levels. Experiments were performed on thin sections taken from fish exposed to media with different pH and aluminium concentration. Aluminium was found on the surface of the gill lamellae, but also inside the tissue. Bulk analysis of the gills showed much higher concentrations in the aluminium-exposed fish, compared to the control ones, but no information regarding the actual accumulation sites can be inferred. Extensive study of damage done to the sample by intense proton beams during elemental analysis was performed with scanning transmission ion microscopy. 3 refs., 3 figs.

A study of aluminium-exposed fish using a scanning proton microprobe

Energy Technology Data Exchange (ETDEWEB)

Cholewa, M.; Legge, G.L.F. [Melbourne Univ., Parkville, VIC (Australia). School of Physics; Eeckhaoudt, S.; Van Grieken, R. [Universitaire Instelling Antwerpen, Antwerp (Belgium)

1993-12-31

A major problem has arisen in Europe with the depopulation of fresh water fish in lakes and streams collecting acid rain. The sensitivity to acidification is species specific and appears to be associated with metal levels. The Scanning Proton Microprobe (SPMP) at the Micro Analytical Research Centre of the University of Melbourne was used to study the subcellular distribution of aluminium and other elements in the gills of fish exposed to acidified water with elevated Al-levels. Experiments were performed on thin sections taken from fish exposed to media with different pH and aluminium concentration. Aluminium was found on the surface of the gill lamellae, but also inside the tissue. Bulk analysis of the gills showed much higher concentrations in the aluminium-exposed fish, compared to the control ones, but no information regarding the actual accumulation sites can be inferred. Extensive study of damage done to the sample by intense proton beams during elemental analysis was performed with scanning transmission ion microscopy. 3 refs., 3 figs.

Process Simulation of Aluminium Sheet Metal Deep Drawing at Elevated Temperatures

International Nuclear Information System (INIS)

Winklhofer, Johannes; Trattnig, Gernot; Lind, Christoph; Sommitsch, Christof; Feuerhuber, Hannes

2010-01-01

Lightweight design is essential for an economic and environmentally friendly vehicle. Aluminium sheet metal is well known for its ability to improve the strength to weight ratio of lightweight structures. One disadvantage of aluminium is that it is less formable than steel. Therefore complex part geometries can only be realized by expensive multi-step production processes. One method for overcoming this disadvantage is deep drawing at elevated temperatures. In this way the formability of aluminium sheet metal can be improved significantly, and the number of necessary production steps can thereby be reduced. This paper introduces deep drawing of aluminium sheet metal at elevated temperatures, a corresponding simulation method, a characteristic process and its optimization. The temperature and strain rate dependent material properties of a 5xxx series alloy and their modelling are discussed. A three dimensional thermomechanically coupled finite element deep drawing simulation model and its validation are presented. Based on the validated simulation model an optimised process strategy regarding formability, time and cost is introduced.

A study of aluminium-exposed fish using a scanning proton microprobe

International Nuclear Information System (INIS)

Cholewa, M.; Legge, G.L.F.

1993-01-01

A major problem has arisen in Europe with the depopulation of fresh water fish in lakes and streams collecting acid rain. The sensitivity to acidification is species specific and appears to be associated with metal levels. The Scanning Proton Microprobe (SPMP) at the Micro Analytical Research Centre of the University of Melbourne was used to study the subcellular distribution of aluminium and other elements in the gills of fish exposed to acidified water with elevated Al-levels. Experiments were performed on thin sections taken from fish exposed to media with different pH and aluminium concentration. Aluminium was found on the surface of the gill lamellae, but also inside the tissue. Bulk analysis of the gills showed much higher concentrations in the aluminium-exposed fish, compared to the control ones, but no information regarding the actual accumulation sites can be inferred. Extensive study of damage done to the sample by intense proton beams during elemental analysis was performed with scanning transmission ion microscopy. 3 refs., 3 figs

Smelter Jobs? Societal changes and employment opportunities for women in East Iceland Er álið málið? Samfélagsbreytingar og atvinnumöguleikar kvenna á Austurlandi

Directory of Open Access Journals (Sweden)

Tinna Kristbjörg Halldórsdóttir

2012-12-01

Full Text Available The period from 2003-2008 was one of upheaval and change in East Iceland with the single largest construction project in Iceland to date; the building of Kárahnjúkar dam and the Fjarðaál Alcoa aluminium smelter. These gave way to various societal changes in the area, such as population increase, new jobs and rise in housing prices, in addition to a range of side effects on the service factor. The aim of this article is to explore if women in the area describe new employment opportunities accompanying these changes. The results are derived from in-depth interviews with 34 women in East Iceland. The interviews unfold the view that a certain ‘modernization’ of the east Icelandic society can be attributed to the smelter construction. However, the women interviewed have difficulty defining whether and how they themselves had profited from the constructions and none of those interviewed in this research named working in the smelter as one of their employment opportunities. Among the reasons discussed were the twelve-hour shifts, lack of flexibilities, long distances and the binding to the workplace during work-hours. Results indicate that an unequal gender balance still remainsin the area.Um miðjan síðasta áratug átti sér stað umrót og breytingar á Austurlandi með stærstu einstöku framkvæmdum Íslandssögunnar; byggingu Kárahnjúkastíflu og álvers Alcoa Fjarðaáls. Framkvæmdunum fylgdu ýmsar samfélagsbreytingar; fjölgun íbúa á svæðinu, fjölgun starfa, hækkun húsnæðisverðs, auk þess sem framkvæmdirnar höfðu margskonar hliðaráhrif á þá þjónustu sem íbúunum stóð til boða. Meginmarkmið þessarar greinar er svara spurningunni; að hvaða marki hafa álversframkvæmdirnar bætt vinnumarkaðsstöðu kvenna á Austurlandi? Auk greiningar lýðfræðilegra gagna og annarra heimilda, byggir greinin á viðtölum við 34 konur búsettar á svæðinu. Engin þeirra vann í álverinu. Helstu niðurstöður s

Study of Surface Roughness and Cutting force in machining for 6068 Aluminium alloy

Science.gov (United States)

Purushothaman, D.; Kaushik Yanamundra, Krishna; Krishnan, Gokul; Perisamy, C.

2018-04-01

Metal matrix composites, in particular, Aluminium Hybrid Composites are gaining increasing attention for applications in air and land because of their superior strength to weight ratio, density and high temperature resistance. Aluminium alloys are being used for a wide range of applications in Aerospace and Automobile industries, to name a few. The Aluminium Alloy 6068 has been used as the specimen. It is mainly composed of Aluminium (93.22 - 97.6 %), Magnesium (0.60 - 1.2 %), Silicon (0.60 - 1.4 %) and Bismuth (0.60 - 1.1 %). Aluminium 6068 is widely used for manufacturing aircraft structures, fuselages and wings. It is also extensively used in fabricating automobile parts such as wheel spacers. In this study, tests for the measurement of surface roughness and cutting force has been carried out on the specimen, the results evaluated and conclusions are drawn. Also the simulation of the same is carried out in a commercial FE software – ABAQUS.

The quality of our drinking water: aluminium determination with an acoustic wave sensor.

Science.gov (United States)

Veríssimo, Marta I S; Gomes, M Teresa S R

2008-06-09

A new methodology based on an inexpensive aluminium acoustic wave sensor is presented. Although the aluminium sensor has already been reported, and the composition of the selective membrane is known, the low detection limits required for the analysis of drinking water, demanded the inclusion of a preconcentration stage, as well as an optimization of the sensor. The necessary coating amount was established, as well as the best preconcentration protocol, in terms of oxidation of organic matter and aluminium elution from the Chelex-100. The methodology developed with the acoustic wave sensor allowed aluminium quantitation above 0.07 mg L(-1). Several water samples from Portugal were analysed using the acoustic wave sensor, as well as by UV-vis spectrophotometry. Results obtained with both methodologies were not statistically different (alpha=0.05), both in terms of accuracy and precision. This new methodology proved to be adequate for aluminium quantitation in drinking water and showed to be faster and less reagent consuming than the UV spectrophotometric methodology.

Ultraviolet Plasmonic Aluminium Nanoparticles for Highly Efficient Light Incoupling on Silicon Solar Cells

Directory of Open Access Journals (Sweden)

Yinan Zhang

2016-05-01

Full Text Available Plasmonic metal nanoparticles supporting localized surface plasmon resonances have attracted a great deal of interest in boosting the light absorption in solar cells. Among the various plasmonic materials, the aluminium nanoparticles recently have become a rising star due to their unique ultraviolet plasmonic resonances, low cost, earth-abundance and high compatibility with the complementary metal-oxide semiconductor (CMOS manufacturing process. Here, we report some key factors that determine the light incoupling of aluminium nanoparticles located on the front side of silicon solar cells. We first numerically study the scattering and absorption properties of the aluminium nanoparticles and the influence of the nanoparticle shape, size, surface coverage and the spacing layer on the light incoupling using the finite difference time domain method. Then, we experimentally integrate 100-nm aluminium nanoparticles on the front side of silicon solar cells with varying silicon nitride thicknesses. This study provides the fundamental insights for designing aluminium nanoparticle-based light trapping on solar cells.

Leaching Behavior of Slags from AN Old Lead Smelter in Chihuahua, Mexico: Metals, Chlorides, Nitrates, Sulfates and Tds Analyses

Science.gov (United States)

Espejel-Garcia, D.; Wenglas-Lara, G.; Villalobos-Aragon, A.; Espejel-Garcia, V. V.

2013-05-01

Waste materials (such as, smelter slags, waste glass, tires, plastics, rubbish, ashes, etc.), have a large potential to substitute natural materials, reducing costs, especially for the construction industry. Smelter slags are resistant and have better compression strength values in comparison to natural aggregates, and generally are far beyond of what the standard ratios need to qualify a material as a good one for construction. But this material has a big problem within it: the existence of toxic elements and compounds in high concentrations, which means that water and soil contamination can be present after water infiltrates through this material; so we perform leaching experiments to characterize and measure the possible contamination under controlled conditions. To perform the slags-leaching experiments, we used an EA-NEN-7375-2004 tank test standard from Netherlands. This test was selected because to our knowledge it is the only one which allows the use of coarse material, as the one utilized in construction. The leaching experiments sampling was performed at different times: 6, 24, 168 and 360 hours, to compare the leachate concentration at the two different pH's values (5 and 8) selected to simulate real conditions. For the leaching experiments, the slags were mixed with natural road base material (gravel-sands from volcanic rocks) at different proportions of 30% and 50%. In order to understand the slags' leaching behavior, other experiments were carried out with the pure material, for both (slags and natural aggregates). After analyses by ICP-OES , the slags from this smelter in Chihuahua contain Pb (0.5 - 4 wt.%), Zn (15-35 wt.%) and As (0.6 wt.%), as well such as: bicarbonates, chlorides, nitrates, sulfates, Mg, K, Na, Ca and TDS. Based on the results of the leaching analyses, via atomic absorption technique, we conclude that Pb and As concentrations are provided by the slags, meanwhile, the bicarbonates, chlorides, Na and Ca are contributed by the road

Visualisation and quantification of heavy metal accessibility in smelter slags: The influence of morphology on availability

International Nuclear Information System (INIS)

Morrison, Anthony L.; Swierczek, Zofia; Gulson, Brian L.

2016-01-01

The Imperial Smelting Furnace (ISF) for producing lead and zinc simultaneously has operated on four continents and in eleven countries from the 1950's. One of the process changes that the ISF introduced was the production of a finely granulated slag waste. Although this slag contained significant amounts of residual lead (Pb) and zinc (Zn), because of its glassy nature it was considered environmentally benign. From the Cockle Creek smelter near Boolaroo at the northern end of Lake Macquarie, NSW, Australia, it is estimated that around 2.1 million tonnes of the fine slag was distributed into the community and most remains where it was originally utilised. Residual tonnages of slag of this magnitude are common worldwide wherever the ISF operated. Studies of base metal smelting slags have concluded that mineralogical and morphological characteristics of the slag play a critical role in moderating environmental release of toxic elements. Scanning electron microscopy (SEM) and microanalysis of the ISF slags has shown that the Pb and associated elements are present as discrete nodules (∼6–22 μm) in the slag and that they are not associated with Zn which is contained in the glass slag phase. Using an automated SEM and analysis technique (QEMSCAN"®) to “map” the mineralogical structure of the particles, it was possible to quantitatively determine the degree of access infiltrating fluids might have to the reaction surface of the Pb phases. The level of access decreases with increasing particle size, but in even the largest sized particles (−3350 + 2000 μm) nearly 80% of the Pb-containing phases were totally or partially accessible. These results provide evidence that the toxic elements in the slags are not contained by the glassy phase and will be vulnerable to leaching over time depending on their individual phase reactivity. - Highlights: • QEMSCAN"® allowed determination of access to infiltrating fluids to Pb in smelter slags. • Pb and associated

Recycling of Metals

DEFF Research Database (Denmark)

Damgaard, Anders; Christensen, Thomas Højlund

2011-01-01

Metals like iron and aluminium are produced from mineral ore and used for a range of products, some of which have very short lifetimes and thus constitute a major fraction of municipal waste. Packaging in terms of cans, foils and containers are products with a short lifetime. Other products like...... appliances, vehicles and buildings, containing iron and aluminium metals, have long lifetimes before they end up in the waste stream. The recycling of production waste and postconsumer metals has a long history in the metal industry. Some metal smelters are today entirely based on scarp metals. This chapter...... describes briefly how iron and aluminium are produced and how scrap metal is recycled in the industry. Quality requirements and use of recycled products are discussed, as are the resource and environmental issues of metal recycling. Copper and other metals are also found in waste but in much smaller...

Studying of metals distribution in the Pinus Sylvestris bark and needles in a zone of influence the gradient polluted air stream from Cu-smelter

International Nuclear Information System (INIS)

Aminov, P.G.; Lonshchakova, G.F.

2008-01-01

In the paper the features of accumulation for heavy metals by pine needles and bark in the gradient dispersion area of technogenic elements and using of the bark as the bioindicator to establish influencing zones of smelter on environment are represented

Aluminium and energy. An interview

Energy Technology Data Exchange (ETDEWEB)

Meyer, E R

1978-06-01

The interview between METALL and the president of Aluswuisse refers mainly to aspects of energy and deals more closely with the questions whether western Europe in view of relatively high prices for electricity is still competitive and which part can be played by aluminium in overcoming the energy crisis.

COMBINED ALUMINIUM SULFATE/HYDROXIDE PROCESS FOR ...

African Journals Online (AJOL)

sulfate, and used for fluoride removal from water by combining with Nalgonda Technique. ... effects on human health and could result in fluorosis. ... [23], nanoscale aluminium oxide hydroxide (AlOOH) [24] and natural zeolite [25], were among.

Response function of NaI(Tl) detectors and multiple backscattering of gamma rays in aluminium

International Nuclear Information System (INIS)

Sabharwal, Arvind D.; Singh, Manpreet; Singh, Bhajan; Sandhu, B.S.

2008-01-01

The response function, converting the observed pulse-height distribution of a NaI(Tl) detector to a true photon spectrum, is obtained experimentally with the help of an inverse matrix approach. The energy of gamma-ray photons continuously decreases as the number of scatterings increases in a sample having finite dimensions when one deals with the depth of the sample. The present experiments are undertaken to study the effect of target thickness on intensity distribution of gamma photons multiply backscattered from an aluminium target. A NaI(Tl) gamma-ray detector detects the photons backscattered from the aluminium target. The subtraction of analytically estimated singly scattered distribution from the observed intensity distribution (originating from interactions of primary gamma-ray photons with the target) results in multiply backscattered events. We observe that for each incident gamma photon energy, the number of multiply backscattered photons increases with increase in target thickness and then saturates at a particular target thickness called the saturation thickness (depth). Saturation thickness for multiply backscattering of gamma photons is found to decrease with increase in energy of incident gamma-ray photons

Research progress of aluminium alloy endplates for PEMFCs

Energy Technology Data Exchange (ETDEWEB)

Fu, Yu.; Hou, Junbo [Fuel Cell system and Engineering Laboratory, Dalian Institute of Chemical and Physics, Chinese Academy of Sciences, Dalian 116023 (China); Graduate University of Chinese Academy of Sciences, Beijing 100049 (China); Hou, Ming; Yan, Xiqiang; Luo, Xiaokuan; Shao, Zhigang; Yi, Baolian [Fuel Cell system and Engineering Laboratory, Dalian Institute of Chemical and Physics, Chinese Academy of Sciences, Dalian 116023 (China)

2007-04-15

The endplate is a crucial component in a proton exchange membrane fuel cell (PEMFC) stack. It can provide the necessary rigidity and strength for the stack. An aluminium alloy is one of the ideal materials for PEMFC endplates because of its low density and high rigidity. But it does not meet the requirements of corrosion resistance and electrical insulation in PEMFC environments. In this work, methods of sealing treatments and the conditions of aluminium alloy anodization were investigated. Corrosion resistances of the samples prepared by different technologies were evaluated in simulated PEMFC environments. The results showed that the corrosion resistance of the samples sealed by epoxy resin was greatly improved compared with those sealed in boiling water, and the samples anodized at a constant current density performed better than those anodized at a constant voltage. By insulation measurements, all of the samples showed good electrical insulation. The aluminium alloy endplate anodized at a constant current density and sealed with thermosetting bisphenol-A epoxy resin exhibited promising potential for practical applications by assembling it in a PEMFC stack and applying a life test. (author)

Phase composition and properties of rapidly cooled aluminium-zirconium-chromium alloys

International Nuclear Information System (INIS)

Sokolovskaya, E.M.; Badalova, L.M.; Podd''yakova, E.I.; Kazakova, E.F.; Loboda, T.P.; Gribanov, A.V.

1989-01-01

Using the methods of physicochemical analysis the interaction of aluminium with zirconium and chromium is studied. Polythermal cross sections between Al 3 -Zr-Al 7 Cr and radial polythermal cross section from aluminium-rich corner with the ratio of components Zr:Cr=5:7 by mass are constructed. The effect of zirconium and chromium content on electrochemical characteristics of aluminium-base rapidly quenching alloys in systems Al-Cr, Al-Zr, Al-Cr-Zr. An increase in chromium concentration in oversaturated solid solution of Al-Cr system expands considerably the range of passive state. When Al 7 Cr phase appears the range of passive stae vanishes

Quantification of aluminium-27 NMR spectra of high-surface-area oxides

International Nuclear Information System (INIS)

Pearson, R.M.; Schramm, C.M.

1990-01-01

This paper discusses the quantitation of 27 Al NMR spectra. It is showns that the so called 'invisible' aluminium atoms seen by recent workers are completely consistent with known continuous wave NMR studies of the 27 Al NMR spectra of high surface area aluminium oxides. The use of pulsed NMR techniques further complicate the quantitative measurement of 27 Al NMR spectra, especially when high resolution NMR spectrometers are used for this purpose. Methods are described which allow both the estimation of aluminium not seen by continuous wave techniques and the amounts of the NMR spectra lost in pulsed work. (author). 24 refs.; 6 figs.; 1 tab

Non-Contact Thickness and Profile Measurements of Rolled Aluminium Strip Using EMAT

International Nuclear Information System (INIS)

Hobbis, A.; Aruleswaran, A.

2006-01-01

Accurate measurement of strip thickness is a very high priority for the aluminium rolled product industry. This paper presents the findings of trials to measure the thickness of aluminium strip using a send-receive, radially polarised Electromagnetic Acoustic Transducer (EMAT). A broadband EMAT system, developed at Warwick University, UK with a centre frequency of approximately 5 MHz and frequency content up to 12 MHz was used. The resultant ultrasonic waveforms have been processed using Fourier analysis. Static measurements of aluminium alloy samples in the thickness range between 0.28 mm to 2.8 mm have been measured using this non-contact approach at stand-offs of up to 2 mm. Measurements across the aluminium strip width to evaluate its profile for quality control was also carried out successfully. Some of the experiments and results obtained are described in detail

Novel package for inhibition of aluminium corrosion in alkaline solutions

Energy Technology Data Exchange (ETDEWEB)

Abdel-Gaber, A.M., E-mail: ashrafmoustafa@yahoo.com [Chemistry Department, Faculty of Science, Alexandria University, Ibrahimia, P.O. Box 426, Alexandria 21321 (Egypt); Khamis, E.; Abo-Eldahab, H.; Adeel, Sh. [Chemistry Department, Faculty of Science, Alexandria University, Ibrahimia, P.O. Box 426, Alexandria 21321 (Egypt)

2010-11-01

Inhibition of aluminium corrosion in 2 M sodium hydroxide solution by a package composed of the cationic surfactant cetyl trimethyl ammonium bromide (CTAB) and lupine seed extract has been investigated employing different electrochemical techniques and chemical gasometry measurements. Potentiodynamic polarization curve measurements showed that lupine seed extract controls both the anodic dissolution of aluminium and the hydrogen gas evolved at the cathodic sites of aluminium surface. Nyquist plots showed two capacitive semicircles in the high and low frequency regions separated by an inductive loop at intermediate frequencies. The inductive loop may be explained by the occurrence of adsorbed intermediates on the surface. A proposed equivalent circuit was used to analyse the impedance spectra for aluminium in NaOH solutions. The corrosion inhibition data have been analysed using different isotherms. The results showed excellent agreement between the kinetic-thermodynamic model and Flory-Huggins isotherm. Gasometry measurements showed that the Inhibitive effect of the surfactant increases at a composition around its critical micelle concentration (cmc). The presence of both the surfactant and lupine seed extract did not indicate synergistic action between them. The mode of adsorption of the surfactant molecules corresponding to their structure is also discussed.

Novel package for inhibition of aluminium corrosion in alkaline solutions

International Nuclear Information System (INIS)

Abdel-Gaber, A.M.; Khamis, E.; Abo-Eldahab, H.; Adeel, Sh.

2010-01-01

Inhibition of aluminium corrosion in 2 M sodium hydroxide solution by a package composed of the cationic surfactant cetyl trimethyl ammonium bromide (CTAB) and lupine seed extract has been investigated employing different electrochemical techniques and chemical gasometry measurements. Potentiodynamic polarization curve measurements showed that lupine seed extract controls both the anodic dissolution of aluminium and the hydrogen gas evolved at the cathodic sites of aluminium surface. Nyquist plots showed two capacitive semicircles in the high and low frequency regions separated by an inductive loop at intermediate frequencies. The inductive loop may be explained by the occurrence of adsorbed intermediates on the surface. A proposed equivalent circuit was used to analyse the impedance spectra for aluminium in NaOH solutions. The corrosion inhibition data have been analysed using different isotherms. The results showed excellent agreement between the kinetic-thermodynamic model and Flory-Huggins isotherm. Gasometry measurements showed that the Inhibitive effect of the surfactant increases at a composition around its critical micelle concentration (cmc). The presence of both the surfactant and lupine seed extract did not indicate synergistic action between them. The mode of adsorption of the surfactant molecules corresponding to their structure is also discussed.

Hydrogen generation from aluminium corrosion in reactor containment spray solutions

International Nuclear Information System (INIS)

Frid, W.; Karlberg, G.; Sundvall, S.B.

1982-01-01

The aluminium corrosion experiments in reactor containment spray solutions, under the conditions expected to prevail during LOCA in BWR and PWR, were performed in order to investigate relationships between temperature, pH and hydrogen production rates. In order to simulate the conditions in a BWR containment realistic ratios between aluminium surface and water volume and between aluminium surface and oxygen volume were used. Three different aluminium alloys were exposed to spray solutions: AA 1050, AA 5052 and AA 6082. The corrosion rates were measured for BWR solutions (deaerated and aerated) with pH 5 and 9 at 50, 100 and 150 0 C. The pressure was constantly 0.8 MPa. The hydrogen production rate was measured by means of gas chromatography. In deionized BWR water the corrosion rates did not exceed about 0.05 mm/year in all cases, i.e. were practically independent of temperature and pH. Hydrogen concentrations were less than 0.1 vol.% in cooled dry gas. Corrosion rates and hydrogen production in PWR alkaline solution measured at pH 9.7 and 150 0 C were very high. AA 5052 alloy was the best material

Mechanical properties of plasma-sprayed layers of aluminium and aluminium alloy on AZ 91

Czech Academy of Sciences Publication Activity Database

Kubatík, Tomáš František; Ctibor, Pavel; Mušálek, Radek; Janata, Marek

2017-01-01

Roč. 51, č. 2 (2017), s. 323-327 ISSN 1580-2949 R&D Projects: GA ČR(CZ) GP14-31538P Institutional support: RVO:61389021 Keywords : plasma spraying of aluminium * adhesion of coating * wear * magnesium alloy AZ91 Subject RIV: JG - Metallurgy OBOR OECD: Materials engineering Impact factor: 0.436, year: 2016

Microstructures of alloyed and dispersed hard particles in the aluminium surface

CSIR Research Space (South Africa)

Pityana, S

2010-03-01

Full Text Available Laser surface alloying of A1200 aluminium alloy was carried out using a 4.4 kW Nd:YAG laser. Powder mixtures of SiC and TiC hard particles were injected into the laser generated melt pool on the aluminium substrate using a commercial powder feeder...

Effect of heat treatment on anodic activation of aluminium by trace element indium

Energy Technology Data Exchange (ETDEWEB)

Graver, Brit [Department of Materials Science and Engineering, Norwegian University of Science and Technology, N-7491 Trondheim (Norway); Helvoort, Antonius T.J. van [Department of Physics, Norwegian University of Science and Technology, N-7491 Trondheim (Norway); Nisancioglu, Kemal, E-mail: kemal.nisancioglu@material.ntnu.n [Department of Materials Science and Engineering, Norwegian University of Science and Technology, N-7491 Trondheim (Norway)

2010-11-15

Research highlights: {yields} Indium segregation activates AlIn alloy surface anodically in chloride solution. {yields} Enrichment of In on Al surface can occur thermally by heat treatment at 300 {sup o}C. {yields} Increasing temperature homogenises indium in aluminium reducing anodic activation. {yields} Indium can activate AlIn surface by segregating through dealloying of aluminium. {yields} Anodic activation is caused by AlIn amalgam formation at aluminium surface. - Abstract: The presence of trace elements in Group IIIA-VA is known to activate aluminium anodically in chloride environment. The purpose of this paper is to investigate the surface segregation of trace element In by heat treatment and resulting surface activation. Model binary AlIn alloys, containing 20 and 1000 ppm by weight of In, were characterized after heat treatment at various temperatures by use of glow discharge optical emission spectroscopy, electron microscopy and electrochemical polarization. Heat treatment for 1 h at 300 {sup o}C gave significant segregation of discrete In particles (thermal segregation), which activated the surface. Indium in solid solution with aluminium, obtained by 1 h heat treatment at 600 {sup o}C, also activated by surface segregation of In on alloy containing 1000 ppm In, resulting from the selective dissolution of the aluminium component during anodic oxidation (anodic segregation). The effect of anodic segregation was reduced by decreasing indium concentration in solid solution; it had negligible effect at the 20 ppm level. The segregated particles were thought to form a liquid phase alloy with aluminium during anodic polarization, which in turn, together with the chloride in the solution destabilized the oxide.

Theoretical study of the lowest-lying electronic states of Aluminium monoiodide

International Nuclear Information System (INIS)

Taher, F.; Kabbani, A.; Ani-El Houte, W.

2004-01-01

Full text.The spectroscopic study of Aluminium monohalides, especially the Aluminium monoiodide, is important for monitoring such species in high temperature fast-flow reactors. Theoretical calculations of AlI are not available, whereas several studies have been done for the other aluminium monohalides. In this work, CAS-SCF/MRCI calculations are performed for the lowest-lying electronic states of AlI in a range of internuclear distance between 2.30 A and 2.80 A. Ab-initio calculations have been effectuated by using the computational chemistry program Molpro. The basis set used in this study for aluminium atom is that used by Langhoff for aluminium monohalides, of contractions using atomic natural orbitals and a pseudopotential is used for iode. Accurate theoretical spectroscopic constants and potential curves are obtained for the ground state X 1 Σ + and the first excited states a 3 Π and A 1 Π. The calculated values of Te, ωe, ωexe and re of these states are compatible with the experimental results. An ordering of states is represented for the lowest five predicted singlet and lowest five predicted triplet states. These results provide a big support to determine the analogy in the ordering of the electronic states in AlF, AlBr and AlI respectively at lower energies. These theoretical results identify a set of electronic singlet and triplet states unobserved experimentally

Inhibition de corrosion des échangeurs thermiques en aluminium et ...

African Journals Online (AJOL)

Ainsi, on peut trouver dans un même circuit de chauffage central la chaudière en aluminium, la tuyauterie en cuivre et les radiateurs en fonte, acier ou aluminium et aussi des matériaux polymères. Nous décrivons un nouvel inhibiteur de corrosion spécifiquement conçu pour protéger les circuits de chauffage central dans ...

Mobility of the element aluminium in the weathering of hard coal material containing pyrites. Investigations on piled-up clay and silt stones of the Upper Carbon layer. Mobilitaet des Elementes Aluminium bei der Verwitterung von pyrithaltigem Steinkohlenbergematerial. Untersuchungen an aufgehaldeten Ton- und Siltsteinen des Oberkarbons

Energy Technology Data Exchange (ETDEWEB)

Finke, G

1992-06-17

In connection with the recultivation problems of mining material, investigations were made of the mobility and toxicity of aluminium in the course of weathering of mining material containing upper carbonic pyrites, and particular attention was paid to interaction of the aluminium with other ions in the weathering solution. From the aluminium type, from the ratios of Ca/Al, Al/SO[sub 4] and Al/TOC, and based on these investigations, the aluminium factor can probably be excluded as the main cause of the difficult recultivation and re-greening of mining material in the first decade of weathering. Only certain types of aluminium have toxic effects. These include ionic aluminium and different aluminium hydroxy compounds. Sulphate, fluoride, nitrate compounds of aluminium and organic aluminium compounds have not proved to be toxic. The proportion of aluminium in the ion pool can be decisive, as shown by the Ca/Al ratio. The ratio of these two cations determines the degree of danger from aluminium, depending on the type of plant. (orig.)

Characterization of nitrogen-ion-implanted aluminium

International Nuclear Information System (INIS)

Rauschenbach, B.; Breuer, K.; Leonhardt, G.

1990-01-01

Aluminium has been implanted with nitrogen ions at different temperatures. The implanted samples have been characterized by Auger electron spectroscopy (AES), X-ray photoelectron spectroscopy (XPS) and electron energy-loss spectroscopy (EELS). Deconvolution procedures are needed to separate the influence of the ion sputter profiling by AES and XPS from the nitrogen-ion-beam-induced effects. The chemical state of Al, N, O and C was identified by deconvolution of the measured spectra. In general, there were double-peak structures observed for N 1s and O 1s, identified as contributions from nitrides and weakly bound nitrogen, and oxides and weakly bound oxygen, respectively. Auger analysis confirms the influence of the nitrogen ion fluence on the shape of the concentration distribution. The influence of temperature on the chemical state of implanted aluminium and on the concentration distribution is discussed. (orig.)

Protective effect of curcumin (Curcuma longa), against aluminium toxicity: Possible behavioral and biochemical alterations in rats.

Science.gov (United States)

Kumar, Anil; Dogra, Samrita; Prakash, Atish

2009-12-28

Aluminium is a potent neurotoxin and has been associated with Alzheimer's disease (AD) causality for decades. Prolonged aluminium exposure induces oxidative stress and increases amyloid beta levels in vivo. Current treatment modalities for AD provide only symptomatic relief thus necessitating the development of new drugs with fewer side effects. The aim of the study was to demonstrate the protective effect of chronic curcumin administration against aluminium-induced cognitive dysfunction and oxidative damage in rats. Aluminium chloride (100 mg/kg, p.o.) was administered to rats daily for 6 weeks. Rats were concomitantly treated with curcumin (per se; 30 and 60 mg/kg, p.o.) daily for a period of 6 weeks. On the 21st and 42nd day of the study behavioral studies to evaluate memory (Morris water maze and elevated plus maze task paradigms) and locomotion (photoactometer) were done. The rats were sacrificed on 43rd day following the last behavioral test and various biochemical tests were performed to assess the extent of oxidative damage. Chronic aluminium chloride administration resulted in poor retention of memory in Morris water maze, elevated plus maze task paradigms and caused marked oxidative damage. It also caused a significant increase in the acetylcholinesterase activity and aluminium concentration in aluminium treated rats. Chronic administration of curcumin significantly improved memory retention in both tasks, attenuated oxidative damage, acetylcholinesterase activity and aluminium concentration in aluminium treated rats (Paluminium-induced cognitive dysfunction and oxidative damage.

Silane pre-treatments on copper and aluminium

International Nuclear Information System (INIS)

Deflorian, F.; Rossi, S.; Fedrizzi, L.

2006-01-01

A large part of aluminium products are coated with an organic layer in order to improve the corrosion resistance. Copper surfaces are also sometimes protected with an organic coating to improve the durability or the aesthetic properties. Examples of industrial applications are household appliances and heat exchanger components. For these applications it is not rare to have the industrial need to treat at the same time components made of aluminium and copper. In order to extend the service life of the organic coated copper a specific surface pre-treatment is often required. Nevertheless, probably because of the limited market of this application, no specific pre-treatments for copper are industrially developed, with the exception of cleaning procedures, but simply extensions of existing pre-treatments optimised for other metals (aluminium, zinc) are used. The application of silane pre-treatments as adhesion promoters for organic coated metals is remarkably increasing in the last decade, because silanes offer very good performance together with high environmental compatibility. The idea is therefore to try to develop a specific silane based pre-treatment for copper. The starting point is the existing silane products for aluminium, optimising the composition and the application conditions (concentration, temperature, pH of the bath, etc.) in order to develop a high performance copper alloy pre-treatment increasing the protective properties and the adhesion of a successively applied organic coating. Moreover these pre-treatments could be used for aluminium alloys too and therefore could be suggested for multi-metals components. The deposits were analysed using FTIR spectroscopy and optical and electron microscopic observations. A careful electrochemical characterisation, mainly by electrochemical impedance spectroscopy measurements (EIS) was carried out to highlight the presence of silane and to evaluate the performance of the different deposits. In order to study an

Tailored Aluminium based Coatings for Optical Appearance and Corrosion Resistance

DEFF Research Database (Denmark)

Aggerbeck, Martin

potential differences in the microstructure, and protection from the network of the Al3Ti phases precipitated during the heat treatment. Laser surface cladding of aluminium containing up to 20 wt. % Ti6Al4V were studied focusing on the microstructure and the alkaline corrosion properties. Due......The current project investigated the possibility of designing aluminium based coatings focusing on the effect of composition and surface finish on the optical appearance and on the alkaline corrosion properties using titanium as the main alloying element. The main results and discussions...... that the roughness after etching increases with higher amounts of alloying elements (especially iron and silicon). Proper polishing requires some alloy hardness, while alloy purity is required for a glossy appearance after anodisation. Magnetron sputtered aluminium based coatings containing up to 18 wt. % titanium...

Insight into the cellular fate and toxicity of aluminium adjuvants used in clinically approved human vaccinations.

Science.gov (United States)

Mold, Matthew; Shardlow, Emma; Exley, Christopher

2016-08-12

Aluminium adjuvants remain the most widely used and effective adjuvants in vaccination and immunotherapy. Herein, the particle size distribution (PSD) of aluminium oxyhydroxide and aluminium hydroxyphosphate adjuvants was elucidated in attempt to correlate these properties with the biological responses observed post vaccination. Heightened solubility and potentially the generation of Al(3+) in the lysosomal environment were positively correlated with an increase in cell mortality in vitro, potentially generating a greater inflammatory response at the site of simulated injection. The cellular uptake of aluminium based adjuvants (ABAs) used in clinically approved vaccinations are compared to a commonly used experimental ABA, in an in vitro THP-1 cell model. Using lumogallion as a direct-fluorescent molecular probe for aluminium, complemented with transmission electron microscopy provides further insight into the morphology of internalised particulates, driven by the physicochemical variations of the ABAs investigated. We demonstrate that not all aluminium adjuvants are equal neither in terms of their physical properties nor their biological reactivity and potential toxicities both at the injection site and beyond. High loading of aluminium oxyhydroxide in the cytoplasm of THP-1 cells without immediate cytotoxicity might predispose this form of aluminium adjuvant to its subsequent transport throughout the body including access to the brain.

Aluminium in food and daily dietary intake assessment from 15 food groups in Zhejiang Province, China.

Science.gov (United States)

Zhang, Hexiang; Tang, Jun; Huang, Lichun; Shen, Xianghong; Zhang, Ronghua; Chen, Jiang

2016-06-01

Aluminium was measured in 2580 samples of 15 food groups and dietary exposure was estimated. Samples were purchased and analysed during 2010 to 2014. High aluminium levels were found in jellyfish (mean 4862 mg/kg), laver (mean 455.2 mg/kg) and fried twisted cruller (mean 392.4 mg/kg). Dietary exposure to aluminium was estimated for Zhejiang residents. The average dietary exposure to aluminium via 15 food groups in Zhejiang Province was 1.15 mg/kg bw/week, which is below the provisional tolerable weekly intake of 2 mg/kg bw /week. Jellyfish is the main Al contributor, providing 37.6% of the daily intake via these 15 food groups. This study provided new information on aluminium levels and assessment of aluminium (Al) dietary exposure in Zhejiang Province of China.

Multiple causes of anaemia amongst children living near a lead smelter in Brazil

Energy Technology Data Exchange (ETDEWEB)

Carvalho, F M; Barreto, M L; Silvany-Neto, A M; Waldron, H A; Tavares, T M

1984-04-05

A prevalence study of anaemia was carried out amongst children, aged one to nine years, living near a lead smelter in Santo Amaro City, Northeast Brazil. It was found that the variation in haemoglobin levels was significantly associated with malnutrition and with the interaction between malnutrition and iron deficiency, but not with lead poisoning, iron deficiency, or hookworm infection, having allowed for the effects of age, area of residence, family per capita income and race. The effect of the interaction between malnutrition and iron deficiency on haemoglobin levels was most prominent amongst children aged one year and amongst those living in the most deprived area. The lack of demonstrable interaction between lead poisoning and iron deficiency in the causation of anaemia amongst these children is discussed.

Mechanochemical synthesis of aluminium nanoparticles and their deuterium sorption properties to 2 kbar

International Nuclear Information System (INIS)

Paskevicius, M.; Webb, J.; Pitt, M.P.; Blach, T.P.; Hauback, B.C.; Gray, E.MacA.; Buckley, C.E.

2009-01-01

A mechanochemical synthesis process has been used to synthesise aluminium nanoparticles. The aluminium is synthesised via a solid state chemical reaction which is initiated inside a ball mill at room temperature between either lithium (Li) or sodium (Na) metal which act as reducing agents with unreduced aluminium chloride (AlCl 3 ). The reaction product formed consists of aluminium nanoparticles embedded within a by-product salt phase (LiCl or NaCl, respectively). The LiCl is washed with a suitable solvent resulting in aluminium (Al) nanoparticles which are not oxidised and are separated from the by-product phase. Synthesis and washing was confirmed using X-ray diffraction (XRD). Nanoparticles were found to be ∼25-100 nm from transmission electron microscopy (TEM) and an average size of 55 nm was determined from small angle X-ray scattering (SAXS) measurements. As synthesised Al/NaCl composites, washed Al nanoparticles, and purchased Al nanoparticles were deuterium (D 2 ) absorption tested up to 2 kbar at a variety of temperatures, with no absorption detected within system resolution.

Eco-technological process of glass-ceramic production from galvanic sludge and aluminium slag

Directory of Open Access Journals (Sweden)

Stanisavljević M.

2010-01-01

Full Text Available Methods of purification of waste water which are most commonly used in the Republic of Serbia belong to the type of conventional systems for purification such as chemical oxidation and reduction, neutralization, sedimentation, coagulation, and flocculation. Consequently, these methods generate waste sludge which, unless adequately stabilized, represents hazardous matter. The aluminium slag generated by melting or diecasting aluminium and its alloys is also hazardous matter. In this sense, this paper establishes ecological risk of galvanic waste sludge and aluminium slag and then describes the process of stabilization of these waste materials by means of transformation into a glass-ceramic structure through sintering. The obtained product was analyzed with Fourier Transform Infrared Spectroscopy (FT-IR and X-ray diffraction (XRD. The object of the paper is the eco-technological process of producing glass-ceramics from galvanic sludge and aluminium slag. The aim of the paper is to incorporate toxic metals from galvanic sludge and aluminium slag into the glass-ceramic product, in the form of solid solutions.

Effects of emissions from aluminium industry in the marine environment; Effekter av utslipp fra aluminiumsindustri i det marine miljoe

Energy Technology Data Exchange (ETDEWEB)

Knutzen, J.; Naes, K.

1994-12-31

This report gives a brief presentation of a literature study of what is known about the effects of PAH (Polycyclic Aromatic Hydrocarbons) on the marine environment and somewhat more summarily about fluoride, acidification and cyanide. Results are also reported for the seven Norwegian fjords which are recipients for aluminium production plants. Norwegian and foreign observations are discussed in relation to critical loads and lack of knowledge. The PAH can accumulate in sediments and organisms and some are potentially carcinogenic. PAH bound to soot particles such as from aluminium production appear not to cause ecological damage beyond one or two km from the emission. However, by elevated PAH levels in sediments the emissions from the aluminium works have been traceable to 30-40 km and more. Lately, large reductions of emission have significantly improved the situation in many of the recipients. Increased content of fluoride and reduced pH is with one exception only a factor within the primary dilution zone of the emission. For fluoride, pH and cyanide, stipulation of critical loads and corresponding acceptable load can be based on water quality criteria. This is not possible for PAH, as there is a lack of water quality criteria and sediment criteria and of reliable toxicity data for PAH. 49 refs., 16 figs., 3 tabs.

Recovery mechanisms in nanostructured aluminium

DEFF Research Database (Denmark)

Yu, Tianbo; Hansen, Niels; Huang, Xiaoxu

2012-01-01

Commercial purity aluminium (99.5%) has been cold rolled to a true strain of 5.5 (99.6% reduction in thickness). The material is very strong but low temperature recovery may be a limiting factor. This has been investigated by isothermal annealing treatments in the temperature range 5–100C. Hardness...

Galvanic corrosion study of aluminium alloy plates mounted to stainless and mild steel bolts by accelerated exposure test

OpenAIRE

MREMA, Emmanuel; ITOH, Yoshito; KANEKO, Akira; HIROHATA, Mikihito

2016-01-01

Despite the fact that aluminium alloy members have a proven durability over stainless steel members, their joint fasteners like bolts, nuts and washers are drawn from steel material due to aluminium alloy inferior mechanical properties. Bare contact between aluminium alloy members and stainless steel fasteners results to galvanic corrosion of aluminium alloy members. A corrosion behaviour study was carried out on different aluminium alloy types with different surface treatments mounted to sta...

Mechanical properties of lightweight aerated concrete with different aluminium powder content

Directory of Open Access Journals (Sweden)

Shabbar Rana

2017-01-01

Full Text Available Aerated concrete is produced by introducing gas into a concrete, the amount dependent upon the requirements for strength. One method to achieve this is by using powdered aluminium which reacts with the calcium hydroxide produced upon hydration of the cement. The aim of the current study was to investigate the influence of the powder content on the mechanical properties of aerated concrete namely; compressive and flexural strengths, modulus of elasticity, density and porosity. The results indicated that an increase in aluminium content caused a decrease in the compressive and tensile strengths. It also produced a decrease in the modulus of elasticity. When the aluminium content increased, the density decreased and the porosity increased.

Spark counting technique of alpha tracks on an aluminium oxide film

International Nuclear Information System (INIS)

Morishima, Hiroshige; Koga, Taeko; Niwa, Takeo; Kawai, Hiroshi

1984-01-01

We have tried to use aluminium oxide film as a neutron detector film with a spark counter for neutron monitoring in the mixed field of neutron and gamma-rays near a reactor. The merits of this method are that (1) aluminium oxide is good electric insulator, (2) any desired thickness of the film can be prepared, (3) chemical etching of the thin film can be dispensed with. The relation between spark counts and numbers of alpha-particles which entered the aluminium oxide film 1 μm thick was linear in the range of 10 5 -10 7 alpha-particles. The sensitivity(ratio of the spark counts to irradiated numbers of alpha-particles) was approximately 10 -3 . (author)

Mercury distribution characteristics in primary manganese smelting plants

International Nuclear Information System (INIS)

Back, Seung-Ki; Sung, Jin-Ho; Moon, Young-Hoon; Kim, Young-Hee; Seok, Kwang-Seol; Song, Geum-Ju; Seo, Yong-Chil

2017-01-01

The mercury (Hg) distribution characteristics were investigated in three primary manganese smelting plants in Korea for the assessment of anthropogenic Hg released. Input and output materials were sampled from each process, and Hg concentrations in the samples were analyzed. Among the input materials, the most mercury was found in the manganese ore (83.1–99.7%) and mercury was mainly released through fly ash or off gas, depending on the condition of off gas cleaning system. As off gas temperature decreases, proportion and concentration of emitted gaseous elemental mercury (Hg 0 ) in off gas decreases. Based on mass balance study from these three plants and national manganese production data, the total amount of mercury released from those Korean plants was estimated to 644 kg/yr. About half of it was emitted into the air while the rest was released to waste as fly ash. With the results of this investigation, national inventory for Hg emission and release could be updated for the response to Minamata Convention on Mercury. - Graphical abstract: 1. Lack of data on mercury (Hg) distribution in manganese smelters. 2. Mass distribution of Hg released from 3 plants (as normalized values) were made as follows by measurements. 3. Information of distribution of Hg in Manganese smelters would be used for emission in to air and releases to other streams for the nation and globe in UNEP mercury report. - Highlights: • The mass balance study by on-site measurement from primary manganese smelting plants was made at first time in the world. • Hg distribution and main input and release pathways of Hg from primary manganese smelting plants could be found as the first time. • Gas temperature in bag filter affects Hg behavior and speciation changes in APCDs. • National inventory of Hg emssion has been updated with new data. - Mercury distribution in manganese smelting plant was investigated as the first measurements at commercial plants in the world. National Hg release

Absorption of aluminium X-ray lines in a laser created gold plasma

International Nuclear Information System (INIS)

Combis, P.; Busquet, M.; Louis-Jacquet, M.

1986-04-01

We have studied the absorption of aluminium X-ray lines through a gold plasma by focusing a high intensity laser-beam onto a specific target. Absorption in the wavelength range of 5 to 7 A has been evidenced and measured for Aluminium resonance lines

Centrifuge experiments for removal of aluminium turbidity from Dhruva heavy water

International Nuclear Information System (INIS)

Shetiya, R.S.; Unny, V.K.P.; Nayak, A.P.

1989-01-01

Aluminium turbidity and associated radioactivity was observed in the moderator cum coolant system of Dhruva during initial power operation. Ion exchange resin beds of the purification system were not able to remove aluminium turbidity and radioactivity of system heavy water. Centrifuge technique was used as a convenient alternative method to remove the turbidity and radioactivity. (author)

Determination of cadmium in aluminium by atomic absorption spectrometry

International Nuclear Information System (INIS)

Batistoni, D.A.; Erlijman, L.H.

1978-12-01

A direct method for the determination of cadmium in elemental aluminium is described. Metal samples are dissolved in diluted hydrochloric acid and cadmium is determined by atomic absorption spectrometry in an air-acetylene flame. Interference by non-specific absorption observed at the analytical wavelength incorrected for by means of a non-absorbing line emitted by the hollow-cathode lamp. Relatively large amounts of arsenic do not interfere. The minimun determinable concentration of cadmium for this procedure is 2-3 ppm, expressed on aluminium basis. (author) [es

Oxidation and waste-to-energy output of aluminium waste packaging during incineration: A laboratory study.

Science.gov (United States)

López, Félix A; Román, Carlos Pérez; García-Díaz, Irene; Alguacil, Francisco J

2015-09-01

This work reports the oxidation behaviour and waste-to-energy output of different semi-rigid and flexible aluminium packagings when incinerated at 850°C in an air atmosphere enriched with 6% oxygen, in the laboratory setting. The physical properties of the different packagings were determined, including their metallic aluminium contents. The ash contents of their combustion products were determined according to standard BS ISO 1171:2010. The net calorific value, the required energy, and the calorific gain associated with each packaging type were determined following standard BS EN 13431:2004. Packagings with an aluminium lamina thickness of >50μm did not fully oxidise. During incineration, the weight-for-weight waste-to-energy output of the packagings with thick aluminium lamina was lower than that of packagings with thin lamina. The calorific gain depended on the degree of oxidation of the metallic aluminium, but was greater than zero for all the packagings studied. Waste aluminium may therefore be said to act as an energy source in municipal solid waste incineration systems. Copyright © 2015 Elsevier Ltd. All rights reserved.

Summary of structural refinement in hi-silicon aluminium piston alloy with phosphorous as grain refiner

International Nuclear Information System (INIS)

Malik, F.A.; Sheikh, S.T.; Choudhry, A.A.

2003-01-01

Aluminium Silicon Alloys are extensively used in a wide variety of applications. There are numerous variables in composition, production control, final structure which can influence the mechanical properties of Hi - Silicon Piston alloys. Hypereutectic AlSi alloys develop coarse grain primary silicon crystals, which have a strong negative effect on the tensile strength, the ductility, and the hardness. These crystals slow machining and reduce the tool life considerably. Phosphorous addition produce a fine, evenly spread crystal structure, lamellar structure of the silicon changes into a granular structure. (author)

Searching for new aluminium chelating agents: a family of hydroxypyrone ligands.

Science.gov (United States)

Toso, Leonardo; Crisponi, Guido; Nurchi, Valeria M; Crespo-Alonso, Miriam; Lachowicz, Joanna I; Mansoori, Delara; Arca, Massimiliano; Santos, M Amélia; Marques, Sérgio M; Gano, Lurdes; Niclós-Gutíerrez, Juan; González-Pérez, Josefa M; Domínguez-Martín, Alicia; Choquesillo-Lazarte, Duane; Szewczuk, Zbigniew

2014-01-01

Attention is devoted to the role of chelating agents in the treatment of aluminium related diseases. In fact, in spite of the efforts that have drastically reduced the occurrence of aluminium dialysis diseases, they so far constitute a cause of great medical concern. The use of chelating agents for iron and aluminium in different clinical applications has found increasing attention in the last thirty years. With the aim of designing new chelators, we synthesized a series of kojic acid derivatives containing two kojic units joined by different linkers. A huge advantage of these molecules is that they are cheap and easy to produce. Previous works on complex formation equilibria of a first group of these ligands with iron and aluminium highlighted extremely good pMe values and gave evidence of the ability to scavenge iron from inside cells. On these bases a second set of bis-kojic ligands, whose linkers between the kojic chelating moieties are differentiated both in terms of type and size, has been designed, synthesized and characterized. The aluminium(III) complex formation equilibria studied by potentiometry, electrospray ionization mass spectroscopy (ESI-MS), quantum-mechanical calculations and (1)H NMR spectroscopy are here described and discussed, and the structural characterization of one of these new ligands is presented. The in vivo studies show that these new bis-kojic derivatives induce faster clearance from main organs as compared with the monomeric analog. © 2013.

High-speed deposition of protective films of aluminium oxide by the method of reactive magnetron sputtering

International Nuclear Information System (INIS)

Bugaev, S.P.; Zakhrov, A.N.; Ladyzhenskii, O.P.; Sochugov, M.S.

2001-01-01

The high optical characteristics of aluminium films made them attractive for different functional and decorative applications. It is well-known that the corrosion resistance of alloying is determined by the presence of the oxide film on its surface, but on the aluminium films, deposited by vacuum methods, the resistance is extremely low resulting in the relatively rapid failure of the coating. At present, there is a large number of methods of depositing the films of aluminium oxide. In most cases, it is recommended to use reactive magnetron sputtering of an aluminium target in a magnetron spraying system (MSS) using direct current, on dispersion of the target of aluminium oxide in a high-frequency MSS

Superhydrophobic coatings for aluminium surfaces synthesized by chemical etching process

Directory of Open Access Journals (Sweden)

Priya Varshney

2016-10-01

Full Text Available In this paper, the superhydrophobic coatings on aluminium surfaces were prepared by two-step (chemical etching followed by coating and one-step (chemical etching and coating in a single step processes using potassium hydroxide and lauric acid. Besides, surface immersion time in solutions was varied in both processes. Wettability and surface morphologies of treated aluminium surfaces were characterized using contact angle measurement technique and scanning electron microscopy, respectively. Microstructures are formed on the treated aluminium surfaces which lead to increase in contact angle of the surface (>150°. Also on increasing immersion time, contact angle further increases due to increase in size and depth of microstructures. Additionally, these superhydrophobic coatings show excellent self-cleaning and corrosion-resistant behavior. Water jet impact, floatation on water surface, and low temperature condensation tests assert the excellent water-repellent nature of coatings. Further, coatings are to be found mechanically, thermally, and ultraviolet stable. Along with, these coatings are found to be excellent regeneration ability as verified experimentally. Although aforesaid both processes generate durable and regenerable superhydrophobic aluminium surfaces with excellent self-cleaning, corrosion-resistant, and water-repellent characteristics, but one-step process is proved more efficient and less time consuming than two-step process and promises to produce superhydrophobic coatings for industrial applications.

Generation and characterization of nano aluminium powder ...

Indian Academy of Sciences (India)

TECS

Generation and characterization of nano aluminium powder obtained through wire ... Department of Aerospace Engineering, Indian Institute of Technology. Madras, Chennai 600 .... pressure developed due to current flow (z-Pinch). Figure 2.

Sorption of chromium(VI) and chromium(III) on aluminium hydroxide

International Nuclear Information System (INIS)

Music, S.

1986-01-01

Factors that influence the sorption of Cr(VI) and Cr(III) on aluminium hydroxide were investigated. The sorption of chromates decreases as the pH of the suspension increases. The mechanism of CrOsub(4)sup(2-) sorption was interpreted in terms of reactions between chromates and -OH and/or Hsub(2)O groups at the hydroxide/liquid interface. It was shown that chromates are more tightly sorbed on aluminium hydroxide compared to other anions, e.g. chlorides. On the other hand, specifically absorbed anions, such as molybdates, compete strongly with chromates for the sorption sites. The sorption of chromium(III) increases with the pH of the suspension. Also, the sorption of chromium(III) is suppressed in the presence of citrate ions. The best conditions for the fixation of Cr(VI) and Cr(III) by aluminium hydroxide are presented. (author)

Corrosion behaviour of 6063 aluminium alloy in acidic and in alkaline media

Directory of Open Access Journals (Sweden)

Prabhu Deepa

2017-05-01

Full Text Available The corrosion behaviour of 6063 aluminium alloy was investigated in different concentrations of phosphoric acid medium and sodium hydroxide medium at different temperatures. The study was done by electrochemical method, using Tafel polarization technique and electrochemical impedance spectroscopy (EIS technique. The surface morphology was investigated using scanning electron microscope (SEM with Energy-dispersive X-ray spectroscopy (EDX. The results showed that the 6063 aluminium alloy undergoes severe corrosion in sodium hydroxide medium than in phosphoric acid medium. The corrosion rate of 6063 aluminium alloy increased with an increase in the concentration of acid as well as with alkali. The corrosion rate was increased with an increase in temperature. The kinetic parameters and thermodynamic parameters were calculated using Arrhenius theory and transition state theory. Suitable mechanism was proposed for the corrosion of 6063 aluminium alloy in phosphoric acid medium and sodium hydroxide medium. The results obtained by Tafel polarization and electrochemical impedance spectroscopy (EIS techniques were in good agreement with each other.

Fracture mechanisms of aluminium alloy AA7075-T651 under various loading conditions

International Nuclear Information System (INIS)

Pedersen, Ketill O.; Borvik, Tore; Hopperstad, Odd Sture

2011-01-01

The fracture behaviour of the aluminium alloy AA7075-T651 is investigated for quasi-static and dynamic loading conditions and different stress states. The fracture surfaces obtained in tensile tests on smooth and notched axisymmetric specimens and compression tests on cylindrical specimens are compared to the fracture surfaces that occur when a projectile, having either a blunt or an ogival nose shape, strikes a 20 mm thick plate of the aluminium alloy. The stress state in the impact tests is much more complex and the strain rate significantly higher than in the tensile and compression tests. Optical and scanning electron microscopes are used in the investigation. The fracture surface obtained in tests with smooth axisymmetric specimens indicates that the crack growth is partly intergranular along the grain boundaries or precipitation free zones and partly transgranular by void formation around fine and coarse intermetallic particles. When the stress triaxiality is increased through the introduction of a notch in the tensile specimen, delamination along the grain boundaries in the rolling plane is observed perpendicular to the primary crack. In through-thickness compression tests, the crack propagates within an intense shear band that has orientation about 45 o with respect to the load axis. The primary failure modes of the target plate during impact were adiabatic shear banding when struck by a blunt projectile and ductile hole-enlargement when struck by an ogival projectile. Delamination and fragmentation of the plates occurred for both loading cases, but was stronger for the ogival projectile. The delamination in the rolling plane was attributed to intergranular fracture caused by tensile stresses occurring during the penetration event.

Application of PIXE in pollution control of the Matola River in Mozambique-analysis of fish scales

Energy Technology Data Exchange (ETDEWEB)

Guambe, J.F. [Freshwater Research Unit, Department of Zoology, University of Cape Town, Private Bag, Rondebosch 7701 (South Africa); Departamento de Fisica, Universidade Edouardo Mondlane, C.P. 257, Maputo (Mozambique); Materials Research Department, iThemba LABS, P.O. Box 722, Somerset West 7129 (South Africa); Mars, J.A., E-mail: marsja@cput.ac.za [Faculty of Health and Wellness Sciences, Cape Peninsula University of Technology, P.O. Box 1906, Bellville 7535 (South Africa); Day, J. [Freshwater Research Unit, Department of Zoology, University of Cape Town, Private Bag, Rondebosch 7701 (South Africa)

2012-02-15

Since PIXE is able to distinguish concentrations of elements at very small spatial scales, it can be used for estimating levels of metal pollution in biological material. This paper provides a preliminary report of a pilot study on the use of PIXE for the identification and quantification of elements (Al (3 wt%), Si 0.5 wt%), S (1.5 wt%), Cl (15 ppm), Mn (5 ppm), Fe (50 ppm), Ni (3 ppm), Zn (2 ppm), Rb (2 ppm), Sr (800 ppm) and Se (3 ppm)) in scales of the estuarine fish Pomadasys kaakan caught in the Matola River upstream from the Maputo estuary and, downstream of an aluminium smelter. Concentrations of both aluminium and sulphur were high (3 wt% and 1.5 wt%, respectively).

Arsenic and cadmium exposure in children living near a smelter complex in San Luis Potosi, Mexico

Energy Technology Data Exchange (ETDEWEB)

Diaz-Barriga, F.; Santos, M.A.; Mejia, J.J.; Batres, L.; Yanez, L.; Carrizales, L.; Vera, E.; del Razo, L.M.; Cebrian, M.E. (Universidad Autonoma de San Luis Potosi (Mexico))

1993-08-01

The main purpose of this study was to assess environmental contamination by arsenic and cadmium in a smelter community (San Luis Potosi City, Mexico) and its possible contribution to an increased body burden of these elements in children. Arsenic and cadmium were found in the environment (air, soil, and household dust, and tap water) as well as in the urine and hair from children. The study was undertaken in three zones: Morales, an urban area close to the smelter complex; Graciano, an urban area 7 km away from the complex; and Mexquitic, a small rural town 25 km away. The environmental study showed that Morales is the most contaminated of the zones studied. The range of arsenic levels in soil (117-1396 ppm), dust (515-2625 ppm), and air (0.13-1.45 micrograms/m3) in the exposed area (Morales) was higher than those in the control areas. Cadmium concentrations were also higher in Morales. Estimates of the arsenic ingestion rate in Morales (1.0-19.8 micrograms/kg/day) were equal to or higher than the reference dose of 1 microgram/kg/day calculated by the Environmental Protection Agency. The range of arsenic levels in urine (69-594 micrograms/g creatinine) and hair (1.4-57.3 micrograms/g) and that of cadmium in hair (0.25-3.5 micrograms/g) indicated that environmental exposure has resulted in an increased body burden of these elements in children, suggesting that children living in Morales are at high risk of suffering adverse health effects if exposure continues.

Adhesive Bonding of Aluminium Alloy A5754 by Epoxy Resins

Directory of Open Access Journals (Sweden)

Ivan Michalec

2013-01-01

Full Text Available Joining thin sheets of aluminium and its alloys is a promising area in the field of joining materials. Nowadays, joining methods that do not melt the material itself are increasingly being utilised. This paper deals with adhesive bonding of aluminium alloy A5754 by two-component epoxy resins. Theresults show that joints bonded by Hysol 9466 have appropriate mechanical properties, but that joints bonded by Hysol 9492 have better thermal stability.

Micro-spatial variation of soil metal pollution and plant recruitment near a copper smelter in Central Chile

International Nuclear Information System (INIS)

Ginocchio, Rosanna; Carvallo, Gaston; Toro, Ignacia; Bustamante, Elena; Silva, Yasna; Sepulveda, Nancy

2004-01-01

Soil chemical changes produced by metal smelters have mainly been studied on a large scale. In terms of plant survival, determination of small scale variability may be more important because less toxic microhabitats may represent safe sites for successful recruitment and thus for plant survival. Three dominant microhabitats (open spaces and areas below the canopy of Sphaeralcea obtusiloba and Baccharis linearis shrubs) were defined in a heavily polluted area near a copper smelter and characterised in terms of microclimate, general soil chemistry, total and extractable metal concentrations in the soil profile (A 0 horizon, 0-5 and 15-20 cm depth), and seedling densities. Results indicated a strong variability in microclimate and soil chemistry not only in the soil profile but also among microhabitats. Air/soil temperatures, radiation and wind speed were much lower under the canopy of shrubs, particularly during the plant growth season. Soil acidification was detected on top layers (0-5 cm depth) of all microhabitats while higher concentrations of N, Cu and Cd were detected on litter and top soil layers below shrubs when compared to open spaces; however, high organic matter content below shrubs decreased bioavailability of metals. Plant recruitment was concentrated under shrub canopies; this may be explained as a result of the nursery effect exerted by shrubs in terms of providing a more favourable microclimate, along with better soil conditions in terms of macronutrients and metal bioavailability. - Metal availability was different under shrub canopies than in open spaces

Parametric optimisation of heat treated recycling aluminium (AA6061) by response surface methodology

Science.gov (United States)

Ahmad, A.; Lajis, M. A.; Yusuf, N. K.; Shamsudin, S.; Zhong, Z. W.

2017-09-01

Alternating typical primary aluminium production with recycling route should benefit various parties, including the environment since the need of high cost and massive energy consumption will be ruled out. At present, hot extrusion is preferred as the effective solid-state recycling process compared to the typical method of melting the swarf at high temperature. However, the ideal properties of extruded product can only be achieved through a controlled process used to alter the microstructure to impart properties which benefit the working life of a component, which also known as heat treatment process. To that extent, this work ought to investigate the effect of extrusion temperature and ageing time on the hardness of the recycled aluminium chips. By employing Analysis of Variance (ANOVA) for full factorial design with centre point, a total of 11 runs were carried out randomly. Three dissimilar extrusion temperatures were used to obtain gear-shape billet. Extruded billets were cut and ground before entering the treatment phase at three different ageing times. Ageing time was found as the influential factor to affect the material hardness, rather than the extrusion temperature. Sufficient ageing time allows the impurity atoms to interfere the dislocation phenomena and yield great hardness. Yet, the extrusion temperatures still act to assist the bonding activities via interparticle diffusion transport matter.