High gene flow and genetic diversity in three economically important Zanthoxylum Spp. of Upper Brahmaputra Valley Zone of NE India using molecular markers.

Science.gov (United States)

Medhi, K; Sarmah, D K; Deka, M; Bhau, B S

2014-12-01

The genetic diversity in Zanthoxylum species viz.  Zanthoxylum nitidum, Zanthoxylum oxyphyllum and Zanthoxylum rhesta collected from the Upper Brahmaputra Valley Zone of Assam (NE India) was amplified using 13 random amplified polymorphic DNA (RAPD) markers and 9 inter-simple sequence repeat (ISSR) markers. RAPD markers were able to detect 81.82% polymorphism whereas ISSR detected 98.02% polymorphism. The genetic similarities were analyzed from the dendrogram constructed by RAPD and ISSR fingerprinting methods which divided the 3 species of Zanthoxylum into 3 clear different clusters. The principle component analysis (PCA) was carried out to confirm the clustering pattern of RAPD and ISSR analysis. Analysis of molecular variance (AMOVA) revealed the presence of significant variability between different Zanthoxylum species and within the species by both RAPD and ISSR markers. Z. nitidum was found to be sharing a high degree of variation with the other two Zanthoxylum species under study. The Nei's gene diversity (h), Shannon's information index (I), observed number of alleles (na) and effective number of alleles (ne) were also found to be higher in ISSR markers (0.3526, 0.5230, 1.9802 and 1.6145) than in RAPD markers (0.3144, 0.4610, 1.8182 and 1.5571). The values for total genotype diversity for among population (HT), within population diversity (Hs) and gene flow (Nm) were more in ISSR (0.3491, 0.2644 and 1.5610) than RAPD (0.3128, 0.2264 and 1.3087) but the mean coefficient of gene differentiation (GST) was more in RAPD (0.2764) than ISSR (0.2426). A comparison of this two finger printing methods was done by calculating MR, EMI and MI. The correlation coefficient between data matrices of RAPD and ISSR based on Mantel test was found to be significant (r = 0.65612).

In vitro effects of aqueous extracts of Zanthoxylum macrophylla roots ...

African Journals Online (AJOL)

The in vitro effects of aqueous extracts of Zanthoxylum macrophylla roots on the activities of three ATPases (Na+, K+- ; Ca2+- ; and Mg2+-ATPases) were investigated in membrane preparations from human erythrocytes of HbAA, HbAS and HbSS bloods. The activities of these membrane-bound enzymes were determined in ...

Where to prick the apple for skin testing?

Science.gov (United States)

Vlieg-Boerstra, B J; van de Weg, W E; van der Heide, S; Dubois, A E J

2013-09-01

Mal d 1 is not equally distributed over the apple. We aimed to examine the influence of the location of pricking in the apple on prick-to-prick skin prick test (PTP) results. PTPs were performed in autumn 2007 and spring 2008, before the birch pollen season, in 32 Dutch adults with symptoms of oral allergy to fresh apple, using apples harvested in autumn 2007. PTPs with fresh intact and unpeeled Pink Lady, Golden Delicious, Elise, Santana and Modi apples were performed using material obtained from approximately 2 cm near the stalk (top), and the middle region. All PTP responses were greater when performed with apple material near the stalk than from the middle region. In 2007, these differences were statistically significant for Pink Lady, Golden Delicious and Elise, and in 2008, for Pink Lady and Modi. When performing PTPs, the apple should be pricked near the stalk rather than in the middle. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Chemical composition, insecticidal, and antifungal activities of fruit essential oils of three colombian Zanthoxylum species Composición química, actividades insecticida y antifúngica de aceites esenciales de frutos de tres especies Zanthoxylum de Colombia

Directory of Open Access Journals (Sweden)

Juliet A Prieto

2011-03-01

Full Text Available This study determined the chemical composition of essential oils isolated from Zanthoxylum monophyllum (Lam. P. Wilson, Z. rhoifolium Lam., and Z. fagara (L. Sarg. fruits by steam distillation, as well as testing antifungal and insecticidal activities of essential oils as potential pesticides. Gas chromatography-mass spectrometry (GC/MS analysis identified 57 compounds. The main constituents in Z. rhoifolium oil were β-Myrcene (59.03%, β-phellandrene (21.47%, and germacrene D (9.28% , the major constituents of Z. monophyllum oil were sabinene (25.71%, 1,8-cineole (9.19%, and cis-4-thujanol (9.19%, whereas fruit oil of Z. fagara mainly contained germacrene D-4-ol (21.1%, elemol (8.35%, and α-cadinol (8.22%. Zanthoxylum fagara showed the highest activity on Colletotrichum acutatum Simmonds (EC50 153.9 μL L-1 air, and Z. monophyllum was the most active against Fusarium oxysporum Schlechtend: Fr. f. sp. lycopersici (EC50 140.1 μL L-1 air. Zanthoxylum monophyllum essential oil showed significant fumigant activity against Sitophilus oryzae (L.. This study demonstrated that Zanthoxylum essential oils exhibit important fungicidal activity on F. oxysporum and C. acutatum, which could become an alternative to synthetic fungicides to control plant fungal diseases, and Z. monophyllum oil is a potential fumigant against S. oryzae.En este estudio se determinó la composición química de los aceites esenciales de frutos de Zanthoxylum monophyllum (Lam. P. Wilson, Z. rhoifolium Lam. y Z. fagara (L. Sarg. obtenidos mediante destilación por arrastre con vapor y se evaluó la actividad antifúngica e insecticida de los aceites esenciales para estimar su uso como posibles plaguicidas. El análisis por cromatografía de gases-espectrometría de masas (CG/EM permitió la identificación de 57 compuestos. β-Mirceno (59,03%, β-felandreno (21,47% y germacreno D (9,28% fueron los componentes principales del aceite de Z. rhoifolium; los principales componentes

Systemic reaction after performing a food prick-to-prick test. A case report

Directory of Open Access Journals (Sweden)

Karen Estefanía Hernández-Moreno

2017-02-01

Full Text Available Background: Skin prick test is the most widely used test for the diagnosis of IgE-mediated conditions. Commercial extracts are used for its performance, but in the case of fruits and vegetables it is preferable using fresh food. Although both tests possess a good safety profile, hypersensitivity reactions have been recorded. Clinical case: Forty-seven-year old woman with a history of persistent allergic rhinitis, sensitized to the pollen of grasses, olive and salsola; she was referred to an allergology department due to anaphylaxis triggered by the consumption of avocado, cantaloupe, carrots and watermelon. Minutes after skin prick test with standardized extract and skin prick with fresh foods, she developed dyspnea, pruritus, erythema, dizziness and sibilance; she was administered 0.5 mg of intramuscular adrenalin and 4 salbutamol inhalations and placed in the Trendelemburg position. Dyspnea persisted, and vital signs monitoring showed heart and respiratory rates increase and, hence, salbutamol was applied again, together with 2 L/min of oxygen delivered by nasal cannula, intravenous fluids and 100 mg intravenous hydrocortisone; improvement was observed at 40 minutes. The patient was hospitalized for 48 hours. Conclusions: Although skin tests are safe, the risk of hypersensitivity and anaphylactic reactions should not be ruled out, especially in susceptible patients.

Foot Skin Ischemic Necrosis following Heel Prick in a Newborn

Directory of Open Access Journals (Sweden)

Esad Koklu

2013-01-01

Full Text Available There are only a few reports on side effects after heel prick in neonates although heel prick has been performed all over the world for many years. The medicine staff had obtained only a drop of blood by pricking the baby’s heel using a lancet without compressing the heel or foot to measure his blood glucose level 3 hours after birth. However he developed a severe and hemorrhagic skin reaction on his entire left foot, beginning 30 minutes after obtaining the drop of blood by pricking the baby’s heel using a lancet. The lesion, which was treated with topical mupirocin and povidone-iodine solution daily, slowly decreased in size and had almost fully resolved within 3 weeks. He was healthy and 9 months old at the time of writing this paper. We herein report a case of foot skin ischemic necrosis following heel prick in a newborn. To our knowledge this patient is the first case of foot skin ischemic necrosis due to heel prick in newborns.

Alkaloids of root barks of Zanthoxylum spp; Alcaloides das cascas das raizes de Zanthoxylum spp

Energy Technology Data Exchange (ETDEWEB)

Hohlemwerger, Sandra Virginia Alves; Sales, Edijane Matos; Costa, Rafael dos Santos; Velozo, Eudes da Silva [Universidade Federal da Bahia (UFBA), Salvador, BA (Brazil). Fac. de Farmacia. Dept. do Medicamento; Guedes, Maria Lenise da Silva, E-mail: euvelozo@ufba.br [Universidade Federal da Bahia (UFBA), Salvador, BA (Brazil). Inst. de Biologia Herbario Alexandre Leal Costa

2012-07-01

In 1959, Gottlieb and Antonaccio published a study reporting the occurrence of lignan sesamin and triterpene lupeol in Zanthoxylum tingoassuiba. In this work we describe the phytochemical study of the root bark of the Z. tingoassuiba which allowed the identification of the lupeol, sesamin, and alkaloids dihydrochelerythrine, chelerythrine, anorttianamide, cis-N-methyl-canadin, predicentine, 2, 3-methylenedioxy-10,11-dimethoxy-tetrahydro protoberberine. The investigation of hexane and methanol extracts of the root bark of Z. rhoifolium and Z. stelligerum also investigated showed the presence of alkaloids dihydrochelerythrine, anorttianamide, cis-N-methyl-canadine, 7,9-dimethoxy-2,3- methylenedioxybenzophen anthridine and angoline. The occurrence of 2,3-methylenedioxy-10,11-dimethoxy-tetrahydro protoberberine is first described in Z. tingoassuiba and Z. stelligerum. This is also the first report of the presence of hesperidin and neohesperidin in roots of Z. stelligerum (author)

Prick by Prick Induced Anaphylaxis in a Patient with Peanuts and Lupine Allergy: Awareness of Risks and Role of Component Resolved Diagnosis

Science.gov (United States)

Ciccarelli, Anna; Calabrò, Claudia; Imperatore, Clara; Scala, Guglielmo

2014-01-01

A case of anaphylaxis is reported in the course of a prick by prick with Lupinus albus and roasted peanut in a 20-year-old woman. We focused on some main topics. First of all it seems important to underscore the potential risks connected to the practice of the prick-by-prick with fresh foods in allergic patients, especially when testing cross-reactive substances, such as White Lupine, peanuts, or soy. It is important that clinicians who perform prick tests be aware of the risk related with in vivo tests in allergic patients. Second, we discuss the problem of the hidden allergens, such as White Lupine flour, or soy flour which are utilized to improve wheat flour because of their lower cost. Patients with a demonstrated allergy to peanuts should be assessed for lupine allergy and informed about the “hidden allergens” issue. Finally, we believe that component resolved diagnosis, the serum specific IgE against molecular components, that is normally considered a second-level diagnostic step has an important role even as a first line approach at least in some selected cases. PMID:25477973

Enhanced repellency of binary mixtures of Zanthoxylum armatum seed oil, vanillin, and their aerosols to mosquitoes under laboratory and field conditions.

Science.gov (United States)

Kwon, Hyung Wook; Kim, Soon-Il; Chang, Kyu-Sik; Clark, J Marshall; Ahn, Young-Joon

2011-01-01

The repellency of Zanthoxylum armatum seed oil (ZA-SO), alone or in combination with vanillin (VA), its six major constituents, and another four major previously known Zanthoxylum piperitum fruit oil constituents, as well as aerosol products containing 5 or 10% ZA-SO and 5% VA, was evaluated against female Aedes aegypti in laboratory and field studies. Results were then compared with those of N,N-diethyl-3-methylbenzamide (DEET) as a standard. Hand in cage laboratory tests showed that 0.2, 0.1, and 0.05 mg/cm2 ZA-SO resulted in > 92% protection through 30-min postexposure and was not significantly different than 0.05 mg/cm2 DEET. Skin treated with linalool and limonene (from Z. armatum) provided > 80% repellency to female Ae. aegypti at 10-min exposure, whereas cuminaldehyde, citronellal, geranyl acetate, and cuminyl alcohol (from Zanthoxylum piperitum) provided > 90% protection during this same time period. Only cuminaldehyde and citronellal provided complete protection comparable to DEET at 10-min postexposure. After that time, repellency of all plant constituents to mosquitoes was considerably decreased (biting and nuisance caused by mosquitoes.

Prickly pear induces upregulation of liver LDL binding in familial heterozygous hypercholesterolemia

International Nuclear Information System (INIS)

Palumbo, B.; Palumbo, R.; Efthimiou, Y.; Stamatopoulos, J.; Sinzinger, H.; Oguogho, A.; Budinsky, A.; Sinzinger, H.

2003-01-01

The hypoglycemic effect of prickly pear is well known by native local Indian population since a long time. Beside the beneficial effects on lipid metabolism, oxidation injury and platelet function has been claimed in experimental animals. We recently found an upregulation of apo-B/E receptor. We therefore examined 10 patients with isolated heterozygous familial hypercholesterolemia (FH) being enrolled in a dietary run-in phase of 6 weeks after dietary counselling and a further 6 weeks of prickly pear addition. Uptake of autologous 123 I-radiolabeled LDL was determined at entry as well as after 6 weeks of daily prickly pear ingestion. We found a significant (p 176.4 mg/dl; p 123 I-LDL binding by prickly pear in FH-patients in vivo and indicate that prickly pear exerts a significant hypolipidemic action via receptor upregulation. (author)

Usos en medicina folclórica, actividad biológica y fitoquímica de metabolitos secundarios de algunas especies del género Zanthoxylum

Directory of Open Access Journals (Sweden)

Víctor Enríque Macias Villamizar

2013-10-01

Full Text Available ResumenSegún el Herbario Nacional de Colombia de la familia Rutaceae en Colombia se encuentran 150 géneros y 900 especies (1, de las cuales muchas han sido utilizada no sólo en la medicina folklórica (2, 3, 4, 5 en tratamientos digestivos, tónico estomático, diuréticos, sedativos entre otros; sino también determinada su actividad biológica como antiplasmódico y citotóxico (5. En la familia Rutaceae se encuentra el género Zanthoxylum (6, del cual también se utiliza en medicina folklórica que incluyen tratamientos contra la tos, enteritis, diarrea, resfriado, reumatismo y ulceraciones (7, 8, 9, 10, 11; también se ha ensayado su actividad biológica donde se encontró ser efectiva, entre otras, a nivel: antimicrobial (7, 8, 9; citotóxica (12,13; Antiagregación plaquetaria (14, 15, y antitumoral (16. La amplia gama de usos etnobotánicos y farmacológicos convierte a los extractos (o compuestos aislados del género Zanthoxylum en materia prima a utilizar en el desarrollo de ensayos para evaluar la actividad biológica, la cual está asociada a la riqueza de metabolitos secundarios tales como alcaloides, lignanos, terpenos, flavonoides, cumarinas, entre otros; convirtiendo al género Zanthoxylum en objeto de estudió fitoquímico promisorio.En este artículo se realiza un aporte al estudió del género Zanthoxylum, en aspectos relacionados con su fitoquímica, sus usos en medicina folclórica y su actividad biológica; y en consecuencia un aporte pertinente al conocimiento en la Facultad de Ciencias de la Salud, debido a la actual tendencia de recurrir a medicina natural para el desarrollo de medicamentos de relativo bajo costo y con mayor probabilidad de adquisición del mismo. (Duazary 2007; 2: 140 - 159AbstractAccording to the Herbarium National of Colombia the Rutaceae family in Colombia are 150 genus and 900 species (1, of which many have been used not only in the folkloric medicine (2, 3, 4, 5 in digestive treatments, stomatic

Alkaloids of root barks of Zanthoxylum spp

International Nuclear Information System (INIS)

Hohlemwerger, Sandra Virginia Alves; Sales, Edijane Matos; Costa, Rafael dos Santos; Velozo, Eudes da Silva; Guedes, Maria Lenise da Silva

2012-01-01

In 1959, Gottlieb and Antonaccio published a study reporting the occurrence of lignan sesamin and triterpene lupeol in Zanthoxylum tingoassuiba. In this work we describe the phytochemical study of the root bark of the Z. tingoassuiba which allowed the identification of the lupeol, sesamin, and alkaloids dihydrochelerythrine, chelerythrine, anorttianamide, cis-N-methyl-canadin, predicentine, 2, 3-methylenedioxy-10,11-dimethoxy-tetrahydro protoberberine. The investigation of hexane and methanol extracts of the root bark of Z. rhoifolium and Z. stelligerum also investigated showed the presence of alkaloids dihydrochelerythrine, anorttianamide, cis-N-methyl-canadine, 7,9-dimethoxy-2,3- methylenedioxybenzophen anthridine and angoline. The occurrence of 2,3-methylenedioxy-10,11-dimethoxy-tetrahydro protoberberine is first described in Z. tingoassuiba and Z. stelligerum. This is also the first report of the presence of hesperidin and neohesperidin in roots of Z. stelligerum (author)

Effects of pricking, sun-drying and sieving on Ginger (Zingiber ...

African Journals Online (AJOL)

The effect of pricking, sun drying and sieving on the color retention of Nigerian yellow bark ginger were investigated. The exterior and interior surface of fresh, pricked and sun dried medium sized Nigerian ginger rhizomes (Tafin giwa) were analysed for colour variation. The colour values of the exterior surface of fresh ginger ...

The skin prick test – European standards

Directory of Open Access Journals (Sweden)

Heinzerling Lucie

2013-02-01

Full Text Available Abstract Skin prick testing is an essential test procedure to confirm sensitization in IgE-mediated allergic disease in subjects with rhinoconjunctivitis, asthma, urticaria, anapylaxis, atopic eczema and food and drug allergy. This manuscript reviews the available evidence including Medline and Embase searches, abstracts of international allergy meetings and position papers from the world allergy literature. The recommended method of prick testing includes the appropriate use of specific allergen extracts, positive and negative controls, interpretation of the tests after 15 – 20 minutes of application, with a positive result defined as a wheal ≥3 mm diameter. A standard prick test panel for Europe for inhalants is proposed and includes hazel (Corylus avellana, alder (Alnus incana, birch (Betula alba, plane (Platanus vulgaris, cypress (Cupressus sempervirens, grass mix (Poa pratensis, Dactilis glomerata, Lolium perenne, Phleum pratense, Festuca pratensis, Helictotrichon pretense, Olive (Olea europaea, mugwort (Artemisia vulgaris, ragweed (Ambrosia artemisiifolia, Alternaria alternata (tenuis, Cladosporium herbarum, Aspergillus fumigatus, Parietaria, cat, dog, Dermatophagoides pteronyssinus, Dermatophagoides farinae, and cockroach (Blatella germanica. Standardization of the skin test procedures and standard panels for different geographic locations are encouraged worldwide to permit better comparisons for diagnostic, clinical and research purposes.

Larvicidal activity of Zanthoxylum acanthopodium essential oil against the malaria mosquitoes, Anopheles anthropophagus and Anopheles sinensis.

Science.gov (United States)

He, Qi; Wang, Wenxia; Zhu, Liang

2018-05-15

Zanthoxylum acanthopodium has insecticidal effect in Chinese traditional medicine. In this study, the essential oil from the dried Zanthoxylum plant was used as a larvicidal compound against the malaria mosquitoes, Anopheles anthropophagus and Anopheles sinensis. Compounds in the Zanthoxylum essential oil were investigated by gas chromatography and mass spectroscopy (GC-MS). The larvicidal bioassays of the whole oil, as well as the main compounds in the oil (estragole and eucalyptol) were performed using WHO method. In total, 63 main compounds (99.32%) were found in the oils, including estragole (15.46%), eucalyptol (10.94%), β-caryophyllene (5.52%), cis-linalool oxide (3.76%), cis-limonene oxide (3.06%). A dose-dependent effect on mortality was recorded with increasing concentrations of essential oil and compounds increasing mortality of the larvae. Larvicidal bioassays revealed that 24 h LC 50 of the whole essential oil was 36.00 mg/L and LC 90 was 101.49 mg/L against An. anthropophagus, while LC 50 was 49.02 mg/L and LC 90 was 125.18 mg/L against An. sinensis. Additionally, 24 h LC 50 of estragole were 38.56 and 41.67 mg/L against An. anthropophagus and An. sinensis, respectively, while the related LC 90 were 95.90 and 107.89 mg/L. LC 50 of eucalyptol were 42.41 and 45.49 mg/L against An. anthropophagus and An. sinensis, while the related LC 90 were 114.45 and 124.95 mg/L. The essential oil of Z. acanthopodium and its several major compounds may have potential for use in the control of malaria mosquitoes.

Utilization of Prickly Pear Peels to Improve Quality of Pan Bread

International Nuclear Information System (INIS)

Anwar, M.M.; Sallam, E.M.

2016-01-01

This investigation aimed to study utilization of prickly pear peels to improve quality of pan bread. Prickly pear peels powder added to wheat flour 72 % at levels 1.0 and 2.0% to make pan beard. In this study, evaluation of nutrients and chemical constitutes and functional properties of prickly pear peels as well as the rheological properties of dough contained prickly pear peels at levels 1% and 2% has been conducted. Then evaluated organoleptic characteristics of pan bread made of it also determined staling rate. Results showed that prickly pear peels had higher content of 32.67 % fiber, 14.25 % pectin and 87.82 % ascorbic acid, and higher contents of antioxidant components. It consists of 441.11 mg/100 g, total phenols, 35.2 flavonoids mg/100 g and DPPH radical-scavenging 62.14%, also water holding capacity was 1.8 ml H 2 O / g , oil holding capacity 2.35 (ml oil/g) and foam stability 7.15%. The major phenolic compounds Oleuro 1264.407, pyrogallo 1149.68, Benzoic 982.37, 3-oH Tyrosol 588.53, Ellagic 413.26, Chorogenic 271.10, Protocatechuic acid 176.02, P-oH- Benzoic 112.78, Epicatechin105.99, Gallic acid 61.26 ppm. The results revealed that addition of prickly pear peels to wheat flour increased the nutrition values of pan bread made of it due to high contents of fiber, ascorbic acid and natural antioxidants, and also decreased staling which improves the quality of pan bread, as well as increases shelf-life of pan bread.

Hydrothermal synthesis of lindgrenite with a hollow and prickly sphere-like architecture

International Nuclear Information System (INIS)

Xu Jiasheng; Xue Dongfeng

2007-01-01

Lindgrenite [Cu 3 (OH) 2 (MoO 4 ) 2 ] with a hollow and prickly sphere-like architecture has been synthesized via a simple and mild hydrothermal route in the absence of any external inorganic additives or organic structure-directing templates. The hierarchical lindgrenite particles are hollow and prickly spheres, which are comprised of numerous small crystal strips that are aligned perpendicularly to the spherical surface. Two factors are important for the formation of hollow and prickly architecture in the present process. One is the general phenomenon of Ostwald ripening in solution, which can be responsible for the hollow structure; the other is that lindgrenite crystals have a rhombic growth habit, which plays an important role in the formation of prickly surface. Furthermore, Cu 3 Mo 2 O 9 with the similar size and morphology can be easily obtained by a simple thermal treatment of the as-prepared lindgrenite in air atmosphere. - Graphical abstract: Lindgrenite [Cu 3 (OH) 2 (MoO 4 ) 2 ] with a hollow and prickly sphere-like architecture has been synthesized via a hydrothermal route. The hierarchical lindgrenite particles are hollow and prickly spheres, which are comprised of numerous crystal strips that are aligned perpendicularly to the spherical surface. Cu 3 Mo 2 O 9 with the similar size and morphology can be easily obtained by a thermal treatment of the as-prepared lindgrenite

Identification of low allergenic apple cultivars using skin prick tests and oral food challenges

NARCIS (Netherlands)

Vlieg-Boerstra, B. J.; van de Weg, W. E.; van der Heide, S.; Kerkhof, M.; Arens, P.; Heijerman-Peppelman, G.; Dubois, A. E. J.

2011-01-01

As oral allergy syndrome (OAS) symptoms to apple are frequent, we aimed to identify low allergenic apple cultivars and to validate the prick-to-prick skin prick test (SPT) as a suitable screening method. Sixty-eight apple cultivars were tested by SPTs in 33 Dutch adults with OAS, before and during

Identification of low allergenic apple cultivars using skin prick tests and oral food challenges

NARCIS (Netherlands)

Vlieg-Boerstra, B. J.; van de Weg, W. E.; van der Heide, S.; Kerkhof, M.; Arens, P.; Heijerman-Peppelman, G.; Dubois, A. E. J.

P>Background: As oral allergy syndrome (OAS) symptoms to apple are frequent, we aimed to identify low allergenic apple cultivars and to validate the prick-to-prick skin prick test (SPT) as a suitable screening method. Methods: Sixty-eight apple cultivars were tested by SPTs in 33 Dutch adults with

Chemical constituents of the wood from Zanthoxylum quinduense Tul. (Rutaceae)

International Nuclear Information System (INIS)

Patino Ladino, Oscar Javier; Cuca Suarez, Luis Enrique

2010-01-01

Phytochemical investigation of the wood from Zanthoxylum quinduense Tul. allowed the isolation and identification of norchelerythrine, decarine, 6-acetonyldihydrochelerythrine, syringaresinol, evofilin C, p-hydroxybenzaldehyde, vanillic acid, a mixture of b-sitosterol, stigmasterol and campesterol and a mixture of saturated and unsaturated fatty acids, and their esters derivatives. The structures of the isolated compounds were elucidated by spectroscopic techniques and comparison with literature data and the mixture of sterols and fatty acids were identified by GC/MS. The antifungal activity of the ethanolic extract, fractions and pure compounds against Fusarium oxysporum f. sp. lycopersici was determined by bioautography. Evofilin C and nochelerytrine were the only substances that present antifungal activity. (author)

Chemical constituents of the wood from Zanthoxylum quinduense Tul. (Rutaceae)

Energy Technology Data Exchange (ETDEWEB)

Patino Ladino, Oscar Javier; Cuca Suarez, Luis Enrique, E-mail: ojpatinol@unal.edu.c [Universidad Nacional de Colombia, Bogota (Colombia). Facultad de Ciencias. Dept. de Quimica

2010-07-01

Phytochemical investigation of the wood from Zanthoxylum quinduense Tul. allowed the isolation and identification of norchelerythrine, decarine, 6-acetonyldihydrochelerythrine, syringaresinol, evofilin C, p-hydroxybenzaldehyde, vanillic acid, a mixture of b-sitosterol, stigmasterol and campesterol and a mixture of saturated and unsaturated fatty acids, and their esters derivatives. The structures of the isolated compounds were elucidated by spectroscopic techniques and comparison with literature data and the mixture of sterols and fatty acids were identified by GC/MS. The antifungal activity of the ethanolic extract, fractions and pure compounds against Fusarium oxysporum f. sp. lycopersici was determined by bioautography. Evofilin C and nochelerytrine were the only substances that present antifungal activity. (author)

Empirical models in the description of prickly pear shoot (Nopal drying kinetics

Directory of Open Access Journals (Sweden)

Emmanuel M. Pereira

Full Text Available ABSTRACT The objective of this study was to describe the technological process involved in the drying kinetics of fresh-cut prickly pear shoots through numerical and analytical solutions. Shoots of two different prickly pear species were used, ‘Gigante’ and ‘Miúda’. Drying was performed at different temperatures (50, 60, 70 and 80 °C and weighing procedures were made continuously. The experimental data were expressed as moisture ratio. The Page model showed the best fit to the drying kinetics of minimally processed ‘Gigante’ and ‘Miúda’ prickly pear shoots, with the best coefficients of determination and Chi-square. Peleg and Wang & Singh models can not be used to simulate the drying of ‘Gigante’ and ‘Miúda’ prickly pear shoots within the evaluated range of temperatures, showing an incoherent graphic pattern.

Zanthoxylum gilletii (Rutaceae) - a mainly Guineo-Congolian forest tree with a newly discovered disjunction to western Ethiopia

DEFF Research Database (Denmark)

Friis, Ib; Vollesen, Kaj

2010-01-01

Regnskovstræet Zanthoxylum gilletii, der hovedsageligt kendes fra lavlansregnskov i Congo-bækkenet og Vestafrika, er fundet i riverin skov i det vestlige Etiopien. Den disjunkte udbredelse bekræfter den forbindelse, der tidligere er konstateret mellen det vestlige Etiopien og regnskovs- og savann...

Chemical Composition of Essential Oils from Zanthoxylum bungeanum Maxim. and Their Bioactivities against Lasioderma serricorne.

Science.gov (United States)

Zhang, Wen-Juan; Guo, Shan-Shan; You, Chun-Xue; Geng, Zhu-Feng; Liang, Jun-Yu; Deng, Zhi-Wei; Wang, Cheng-Fang; Du, Shu-Shan; Wang, Yong-Yan

2016-10-01

Two essential oil samples were obtained from the pericarp of Zanthoxylum bungeanum with the methods of hydrodistillation (HD) and supercritical fluid CO 2 extraction (SFE), their chemical components were identified, and their bioactivities against Lasioderma serricorne adults were evaluated. In the process of testing, the two samples showed significant bioactivities against Lasioderma serricorne adults. For an example, the SFE-sample expressed relatively stronger fumigant toxicity on Lasioderma serricorne adults (LC 50 = 3.99 μg/mL air) than that of the HD-sample (LC 50 = 12.54 μg/mL air). According to GC-MS analysis, the chemical components between two samples were different. The major chemical components for HD included linalool (25.99%), limonene (19.34%), linalyl anthranilate (12.22%), 4-terpinenol (10.49%), eucalyptol (6.53%) and α-terpineol (5.02%), while for SFE included nonanoic acid (21.43%), γ-terpinene (14.51%), eucalyptol (13.45%), α-terpineol (5.83%) and caryophyllene oxide (5.48%). The results showed that different chemical components result in different bioactivities. This work provides theoretical basis for traditional Chinese concept of antagonistic storage, and it also provides important information for the development and comprehensive utilization of Zanthoxylum bungeanum.

Identification of low allergenic apple cultivars using skin prick tests and oral food challenge tests

NARCIS (Netherlands)

Vlieg-Boerstra, B.J.; Weg, van de W.E.; Heide, van der S.; Arens, P.F.P.; Heijerman-Peppelman, G.; Dubois, A.E.J.

2011-01-01

Background: As oral allergy syndrome (OAS) symptoms to apple are frequent, we aimed to identify low allergenic apple cultivars and to validate the prick-to-prick skin prick test (SPT) as a suitable screening method. Methods: Sixty-eight apple cultivars were tested by SPTs in 33 Dutch adults with

Antioxidant and Anti-Osteoporosis Activities of Chemical Constituents of the Stems of Zanthoxylum piperitum

OpenAIRE

Seo Young Yang; Sang-Hyun Lee; Bui Huu Tai; Hae-Dong Jang; Young Ho Kim

2018-01-01

Two new lignans, zanthoxyloside C (1) and zanthoxyloside D (2), together with nine known compounds comprising lignans (3–5), flavonoids (6–8), and phenolics (9–11), were isolated from the methanol extract of the stems of Zanthoxylum piperitum. All isolates were evaluated for their antioxidant and anti-osteoporotic activities using oxygen radical absorbance capacity (ORAC), cupric reducing antioxidant capacity (CUPRAC), and tartrate-resistant acid phosphatase (TRAP) assays. Compounds 7–10 show...

[YANG's pricking-cupping therapy for knee osteoarthritis: a multi-center randomized controlled trial].

Science.gov (United States)

Wang, Bo; Liu, Xiru; Hu, Zhihai; Sun, Aijun; Ma, Yanwen; Chen Yingying; Zhang, Xuzhi; Liu, Meiling; Wang, Yi; Wang, Shuoshuo; Zhang, Yunjia; Li, Yijing; Shen, Weidong

2016-02-01

To evaluate the clinical efficacy of YANG's pricking-cupping therapy for knee osteoar thritis (KOA). Methods This was a multi-center randomized parallel controlled trial. One hundred and seventy one patients with KOA were randomly allocated to a pricking-cupping group (89 cases) and a conventional acu puncture group (82 cases). Neixiyan (EX-LE 4), Dubi (ST 35) and ashi points were selected in the two groups. Patients in the pricking-cupping group were treated with YANG's pricking-cupping therapy; the seven-star needles were used to perform pricking at acupoints, then cupping was used until slight bleeding was observed. Patients in the conventional acupuncture group were treated with semi-standardized filiform needle therapy. The treatment was given for 4 weeks (from a minimum of 5 times to a maximum of 10 times). The follow-up visit was 4 weeks. The Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC) and the visual analogue scale (VAS) were adopted for the efficacy assessments. The pain score, stiffness score, physical function score and total score of WOMAC were all reduced after 4-week treatment and during follow-up visit in the two groups (all P0. 05), each score and total score of WOMAC in the pricking-cupping group were lower than those in the conventional acupuncture group after 4-week treatment and during follow-up visit (Pcupping group were lower than those in the conventional acupuncture group after 4-week treatment and during follow-up visit (P cupping and conventional acupuncture therapy can both significantly improve knee joint pain and function in patients with KOA, which are relatively safe. The pricking cupping therapy is superior to conventional acupuncture with the identical selection of acupoints.

A Simple Method for the Preparation of ZnO Prickly Spheres

Institute of Scientific and Technical Information of China (English)

Da Zhi LI; Xin Yu SONG; Si Xiu SUN; Jin Xin GUO

2004-01-01

The synthesis of ZnO prickly spheres using precipitation followed by heating treatment was investigated. Zn(OH)2 precursor was prepared by precipitation process using Zn(CH3COO)2·2H2O in mixed 1-propanol-water solvent. Sodium dodecyl sulfate (SDS) as the anionic surfactant was added to control the morphology. The size and structure of ZnO prickly spheres were studied using XRD, TEM and SEM. The results showed that the morphologies and size of the spheres strongly depended on the volume ratio of 1-propanol /water and molar ratio of SDS/Zn2+. ZnO prickly spheres composed of nanorods could be obtained, when the volume ratio of 1-propanol/water = 2:3 and the molar ratio of Zn2+/SDS ≈ 450:1.

Rapid endosomal escape of prickly nanodiamonds: implications for gene delivery

Science.gov (United States)

Chu, Zhiqin; Miu, Kaikei; Lung, Pingsai; Zhang, Silu; Zhao, Saisai; Chang, Huan-Cheng; Lin, Ge; Li, Quan

2015-06-01

The prickly nanodiamonds easily entered cells via endocytosis followed by unique intracellular translocation characteristics—quick endosomal escape followed by stable residence in cytoplasm. Endosomal membrane rupturing is identified as the major route of nanodiamonds’ escaping the vesicle confinement and to the cytoplasm. Little cytotoxicity is observed to associate with the nanodiamonds’ cytosolic release. Such features enable its application for gene delivery, which requires both effective cellular uptake and cytosolic release of the gene. Taking green fluorescent protein gene as an example, we demonstrate the successful cytosolic delivery and expression of such a gene using the prickly nanodiamonds as carrier.

Rapid endosomal escape of prickly nanodiamonds: implications for gene delivery

Science.gov (United States)

Chu, Zhiqin; Miu, Kaikei; Lung, Pingsai; Zhang, Silu; Zhao, Saisai; Chang, Huan-Cheng; Lin, Ge; Li, Quan

2015-01-01

The prickly nanodiamonds easily entered cells via endocytosis followed by unique intracellular translocation characteristics—quick endosomal escape followed by stable residence in cytoplasm. Endosomal membrane rupturing is identified as the major route of nanodiamonds’ escaping the vesicle confinement and to the cytoplasm. Little cytotoxicity is observed to associate with the nanodiamonds’ cytosolic release. Such features enable its application for gene delivery, which requires both effective cellular uptake and cytosolic release of the gene. Taking green fluorescent protein gene as an example, we demonstrate the successful cytosolic delivery and expression of such a gene using the prickly nanodiamonds as carrier. PMID:26123532

Rapid endosomal escape of prickly nanodiamonds: implications for gene delivery.

Science.gov (United States)

Chu, Zhiqin; Miu, Kaikei; Lung, Pingsai; Zhang, Silu; Zhao, Saisai; Chang, Huan-Cheng; Lin, Ge; Li, Quan

2015-06-30

The prickly nanodiamonds easily entered cells via endocytosis followed by unique intracellular translocation characteristics—quick endosomal escape followed by stable residence in cytoplasm. Endosomal membrane rupturing is identified as the major route of nanodiamonds' escaping the vesicle confinement and to the cytoplasm. Little cytotoxicity is observed to associate with the nanodiamonds' cytosolic release. Such features enable its application for gene delivery, which requires both effective cellular uptake and cytosolic release of the gene. Taking green fluorescent protein gene as an example, we demonstrate the successful cytosolic delivery and expression of such a gene using the prickly nanodiamonds as carrier.

Evaluation Of Prick Test In Atopic Dermatitis And Chronic Urticaria

Directory of Open Access Journals (Sweden)

Dhar Sandipan

1997-01-01

Full Text Available “Prick test” was carried out in 15 patients with atopic dermatitis (AD and 10 patients with chronic urticaria (CU. Of the various aeroallergens tested, house dust mite (HDM, pollens, aspergillus furnigatus and insects were found to be most commonly positive. The common food allergens showing prick test positivity were egg white, fish, milk, brinjal, dal, groundnut and banana. Use of nasal filters showed 10-20% improvement in AD and 5 â€" 10% improvement in urticaria. Withdrawal of the responsible food article(s showed 20-30% improvement in patients with AD and urticaria.

Extraction and determination of polyphenols and betalain pigments in the Moroccan Prickly pear fruits (Opuntia ficus indica

Directory of Open Access Journals (Sweden)

Omar Khatabi

2016-09-01

This study has permitted us equally to value betalain pigments extracted from fruity juice. These are the betalains present in the epidermis and the pulp of the prickly pear confers on it its color varying from yellow to purple. Results show that yellow and red prickly pears contain imported strengths in betalains. Our work shows that the red prickly pear contains betaxanthin pigments in excess of the indicaxanthin that permits to valorize human’s potential spring of genuine colorings. Betalains and polyphenols are antioxidants that contribute to nutritional prickly pears’ quality and to their products of transformation.

Inhibitory and enzyme-kinetic investigation of chelerythrine and lupeol isolated from Zanthoxylum rhoifolium against krait snake venom acetylcholinesterase

Energy Technology Data Exchange (ETDEWEB)

Ahmad, Mustaq, E-mail: mushtaq213@yahoo.com [University of Science and Technology, Bannu, (Pakistan). Department of Biotechnology; Weber, Andrea D.; Zanon, Graciane; Tavares, Luciana de C.; Ilha, Vinicius; Dalcol, Ionara I.; Morel, Ademir F., E-mail: ademirfariasm@gmail.com [Universidade Federal de Santa Maria, RS (Brazil). Dept. de Quimica

2014-01-15

The in vitro activity of chelerythrine and lupeol, two metabolites isolated from Zanthoxylum rhoifolium were studied against the venom of the snake Bungarus sindanus (Elapidae). The venom, which is highly toxic to humans, consists mainly by the enzyme acetylcholinesterase (AChE). Both compounds showed activity against the venom, and the alkaloid chelerythrine presented higher activity than did triterpene lupeol. (author)

Natural history of skin prick test reactivity

DEFF Research Database (Denmark)

Schou Nielsen, Jesper; Meteran, Howraman; Ulrik, Charlotte Suppli

2017-01-01

population sample of children and adolescents in relation to symptoms of rhinitis. METHODS: A total of 983 individuals, aged 7 to 17 years, were randomly selected in 1986 and invited to 4 examinations during a 20-year period. During each examination, a skin prick test was performed using common local...

Nutritive value and chemical composition of prickly pear seeds (Opuntia ficus indica L.) growing in Turkey.

Science.gov (United States)

Özcan, Mehmet Musa; Al Juhaimi, Fahad Y

2011-08-01

The proximate composition and physico-chemical properties (moisture, crude lipid, crude protein, ash, and crude fiber, peroxide value, saponification value, acidity, relative density and refractive index) of prickly pear seed and corresponding oil were determined. The mineral contents (Ca, Cu, Fe, K, Mg, Na, P, Mn and Zn) of samples were analyzed by inductively coupled plasma atomic emission spectrometry. Minerals determined were: calcium 471.2 mg/kg, potassium 532.7 mg/kg, magnesium 117.3 mg/kg, phosphorus 1,627.5 mg/kg and natrium 71.3 mg/kg. The fatty acid profiles of seed oil from the Opuntia ficus indica were analyzed by gas chromatography. Linoleic acid was established as the major fatty acid (61.01%), followed by oleic (25.52%) and palmitic (12.23%) acids. Both myristic, stearic and arachidonic acids were detected in O. ficus indica seed oil in low amounts. As a result, O. ficus indica seeds are an important source of natural fiber and, given its high linoleic acid content, its oil can be used as a nutraceutic agent.

Syntheses of Quinazoline-2,4-dione Alkaloids and Analogues from Mexican Zanthoxylum Species â€

Directory of Open Access Journals (Sweden)

R. Somanathan

2004-06-01

Full Text Available Quinazolinone and quinazolinedione derivatives are of considerable interest due to their wide array of pharmacological properties. In this paper we report the synthesis of ten quinazolinediones. The previous isolation of two of these compounds, namely 1-methyl-3-(2'-phenylethyl-1H,3H-quinazoline-2,4-dione and 1-methyl-3-[2'-(4'- methoxyphenylethyl]-lH,3H-quinazoline-2,4-dione, from the seed husks of Mexican Zanthoxylum species has been reported

Ecophysiological and anatomical characteristics of the subtropical shrub Zanthoxylum acanthopodium (Rutaceae) in conditions of a temperate continental climate (Serbia)

DEFF Research Database (Denmark)

Rakic, Tamara; Sinzar-Sekulic, Jasmina; Filipovic, Biljana

2009-01-01

The evergreen shrub Zanthoxylum acanthopodium DC. (Rutaceae), originating from warm temperate and subtropical Asia, has existed successfully in the Jevremovac Botanical Garden in Belgrade for more than 80 years. The seasonal pattern of water management in leaves, electrolyte leakage, essential oil...... composition, and leaf anatomy were examined in order to understand the resistance and viability of this subtropical shrub in the temperate continental climate of Belgrade, Serbia....

[Diagnostic capacity of skin prick test in egg and cow's milk allergic infants].

Science.gov (United States)

Yan, Jun-mei; Chen, Jing; Li, Hai-qi; Hu, Yan

2011-05-01

Mean diameter is the most common used parameter for wheal response assessment after skin prick test. This study aimed to investigate the diagnostic capacity of mean diameter according to the outcome of oral food challenge, and to determine the cut-off points that could render food challenges unnecessary. Data of 173 children referred to the Division of Primary Child Health Care for the evaluation of suspected food allergy were prospectively studied. All children underwent skin prick test and open food challenge to the relevant food(s) in clinic. The mean wheal diameter of skin prick test was measured, and open food challenge was performed to confirm food allergy. The SPSS software package version 13.0 for windows (SPSS, Chicago, IL, USA) was used for all statistical analysis. Open food challenge was taken as the gold standard for diagnosis. Diagnostic capacity of skin prick test, including the sensitivity, specificity, positive predictive value, negative predictive value, was calculated by cross-table. In addition, receiver operating characteristic curve (ROC) was plotted and area under the curve (AUC) was calculated to quantify the accuracy of the parameter. For the 173 children, 271 open food challenges were performed with egg white, egg yolk and cow's milk, In which 123 were positive, 99 children were diagnosed as food allergy. Cutaneous symptoms (87.0%) were most common, followed by gastrointestinal symptoms (9.8%). The AUC of mean diameter was 0.794 for egg white, 0.804 for egg yolk and 0.904 for cow's milk. The sensitivity of skin prick test with a cut-off value of ≥ 3 mm was ranged from 71% to 87%, while the specificity was between 31% and 57%. The authors also defined food specific skin prick test mean diameters that were 100% diagnostic for allergy to egg white (≥ 8.5 mm), egg yolk (≥ 5.5 mm), cow's milk (≥ 5.5 mm). Predictive decision points for a positive outcome of food challenges can be calculated for egg and cow's milk using mean diameter. It

Human finger-prick induced pluripotent stem cells facilitate the development of stem cell banking.

Science.gov (United States)

Tan, Hong-Kee; Toh, Cheng-Xu Delon; Ma, Dongrui; Yang, Binxia; Liu, Tong Ming; Lu, Jun; Wong, Chee-Wai; Tan, Tze-Kai; Li, Hu; Syn, Christopher; Tan, Eng-Lee; Lim, Bing; Lim, Yoon-Pin; Cook, Stuart A; Loh, Yuin-Han

2014-05-01

Induced pluripotent stem cells (iPSCs) derived from somatic cells of patients can be a good model for studying human diseases and for future therapeutic regenerative medicine. Current initiatives to establish human iPSC (hiPSC) banking face challenges in recruiting large numbers of donors with diverse diseased, genetic, and phenotypic representations. In this study, we describe the efficient derivation of transgene-free hiPSCs from human finger-prick blood. Finger-prick sample collection can be performed on a "do-it-yourself" basis by donors and sent to the hiPSC facility for reprogramming. We show that single-drop volumes of finger-prick samples are sufficient for performing cellular reprogramming, DNA sequencing, and blood serotyping in parallel. Our novel strategy has the potential to facilitate the development of large-scale hiPSC banking worldwide.

Antioxidant and Anticlastogenic Capacity of Prickly Pear Juice

Directory of Open Access Journals (Sweden)

Alejandra Hernández-Ceruelos

2013-10-01

Full Text Available Plants belonging to the genus Opuntia spp. are the most abundant of the Cactaceae family, grown throughout America and the Mediterranean central area. Its fruit, known as cactus pear or prickly pear, is an oval berry grouped in different colors. Some studies have shown its antioxidant activities which may help in preventing chronic pathologies such as diabetes. The purpose of the study was to evaluate the antioxidant capacity of three varieties of prickly pear juice (red-purple, white-green and yellow-orange in five different concentrations (100, 250, 500, 750, and 1000 mg/mL by DPPH (1,1-diphenyl-2-picrylhydrazyl radical colorimetric method, selecting the best variety to determine its anticlastogenic potential against methyl methanesulfonate (MMS. The results indicate that the highest antioxidant was found in the juice of the prickly pear red-purple variety (PPRP, in all concentrations. Its anticlastogenic potential was therefore evaluated with a micronucleus assay. The experiment was run over two weeks. A negative control was included along with a positive control with MMS (40 mg/kg, a group of mice treated with PPRP (25 mL/kg, and three groups with PPRP (in doses of 25, 16.5 and 8.3 mL/kg plus the mutagen. The PPRP was administered daily by oral gavage and the MMS was injected intraperitoneally five days prior to the end of the experiment. Blood samples were obtained at 0, 24, 48, 72 and 96 h in order to determine the frequency of micronucleated polychromatic erythrocytes (MNPE. The results indicated that PPRP is not a genotoxic agent, on the contrary, it may reduce the number of MNPE. In this regard, the PPRP showed an anticlastogenic effect directly proportional to its concentrations. Thus, the highest protection was obtained with a concentration of 25 mL/kg after 48 h of treatment.

Antioxidant and Anti-Osteoporosis Activities of Chemical Constituents of the Stems of Zanthoxylum piperitum.

Science.gov (United States)

Yang, Seo Young; Lee, Sang-Hyun; Tai, Bui Huu; Jang, Hae-Dong; Kim, Young Ho

2018-02-18

Two new lignans, zanthoxyloside C ( 1 ) and zanthoxyloside D ( 2 ), together with nine known compounds comprising lignans ( 3 - 5 ), flavonoids ( 6 - 8 ), and phenolics ( 9 - 11 ), were isolated from the methanol extract of the stems of Zanthoxylum piperitum. All isolates were evaluated for their antioxidant and anti-osteoporotic activities using oxygen radical absorbance capacity (ORAC), cupric reducing antioxidant capacity (CUPRAC), and tartrate-resistant acid phosphatase (TRAP) assays. Compounds 7 - 10 showed peroxyl radical-scavenging capacities and 4 , 6 - 7 , and 9 showed reducing capacities. Moreover, compounds 3 , 6 - 9 , and 11 significantly suppressed TRAP activities. These results indicated that the stems of Z. piperitum could be an excellent source for natural antioxidant and anti-osteoporosis.

Histamine 50-skin-prick test: a tool to diagnose histamine intolerance.

Science.gov (United States)

Kofler, Lukas; Ulmer, Hanno; Kofler, Heinz

2011-01-01

Background. Histamine intolerance results from an imbalance between histamine intake and degradation. In healthy persons, dietary histamine can be sufficiently metabolized by amine oxidases, whereas persons with low amine oxidase activity are at risk of histamine toxicity. Diamine oxidase (DAO) is the key enzyme in degradation. Histamine elicits a wide range of effects. Histamine intolerance displays symptoms, such as rhinitis, headache, gastrointestinal symptoms, palpitations, urticaria and pruritus. Objective. Diagnosis of histamine intolerance until now is based on case history; neither a validated questionnaire nor a routine test is available. It was the aim of this trial to evaluate the usefullness of a prick-test for the diagnosis of histamine intolerance. Methods. Prick-testing with 1% histamine solution and wheal size-measurement to assess the relation between the wheal in prick-test, read after 20 to 50 minutes, as sign of slowed histamine degradation as well as history and symptoms of histamine intolerance. Results. Besides a pretest with 17 patients with HIT we investigated 156 persons (81 with HIT, 75 controls): 64 out of 81 with histamine intolerance(HIT), but only 14 out of 75 persons from the control-group presented with a histamine wheal ≥3 mm after 50 minutes (P < .0001). Conclusion and Clinical Relevance. Histamine-50 skin-prickt-test offers a simple tool with relevance.

Analgesia with breastfeeding in addition to skin-to-skin contact during heel prick.

Science.gov (United States)

Marín Gabriel, Miguel Ángel; del Rey Hurtado de Mendoza, Beatriz; Jiménez Figueroa, Lourdes; Medina, Virginia; Iglesias Fernández, Beatriz; Vázquez Rodríguez, María; Escudero Huedo, Virginia; Medina Malagón, Lorena

2013-11-01

To investigate the analgesic effect (measured with Neonatal Infant Pain Scale (NIPS)) of breastfeeding (BF) in addition to skin-to-skin contact (SSC) versus other methods of non-pharmacological analgesia during blood sampling through heel lance in healthy term neonates. Randomised controlled trial. Tertiary level maternity ward. One hundred thirty-six healthy term newborns. healthy term neonates, wish to breastfeed and absence of feeding during the previous 60 min. Neonates were randomly assigned to four groups: Group breastfed with SSC (BF+SSC Group) (n=35); Group sucrose with SSC (Sucrose+SSC Group) (n=35); SSC Group (n=33); or Sucrose Group (n=33). Babies were recorded with a video camera. Three observers watched the videos and measured NIPS score at three time points (t0: 2 min before heel prick; t1: During heel prick; and t2: 2 min after the heel prick). The influences of non-pharmacological methods on crying time, percentage of crying while sampling, heart rate, number of attempts and duration of sampling were also studied. BF+SSC Group achieved a significant lower median NIPS score (value=1) compared with other groups (value=2, 4 and 4, respectively). The percentage of neonates with moderate-to-severe pain was also lower in the BF+SSC Group. Both groups BF+SSC and Sucrose+SSC achieved a significant lower percentage of crying compared with SSC Group. This study suggests that BF in addition to SSC provides superior analgesia to other kinds of non-pharmacological analgesia in healthy term neonates during heel prick.

Trial of Music, Sucrose, and Combination Therapy for Pain Relief during Heel Prick Procedures in Neonates.

Science.gov (United States)

Shah, Swapnil R; Kadage, Shahajahan; Sinn, John

2017-11-01

To compare the effectiveness of music, oral sucrose, and combination therapy for pain relief in neonates undergoing a heel prick procedure. This randomized, controlled, blinded crossover clinical trial included stable neonates >32 weeks of postmenstrual age. Each neonate crossed over to all 3 interventions in random order during consecutive heel pricks. A video camera on mute mode recorded facial expressions, starting 2 minutes before until 7 minutes after the heel prick. The videos were later analyzed using the Premature Infant Pain Profile-Revised (PIPP-R) scale once per minute by 2 independent assessors, blinded to the intervention. The PIPP-R scores were compared between treatment groups using Friedman test. For the 35 participants, the postmenstrual age was 35 weeks (SD, 2.3) with an average weight of 2210 g (SD, 710). The overall median PIPP-R scores following heel prick over 6 minutes were 4 (IQR 0-6), 3 (IQR 0-6), and 1 (IQR 0-3) for the music, sucrose, and combination therapy interventions, respectively. The PIPP-R scores were significantly lower at all time points after combination therapy compared with the groups given music or sucrose alone. There was no difference in PIPP-R scores between the music and sucrose groups. In relatively stable and mature neonates, the combination of music therapy with sucrose provided better pain relief during heel prick than when sucrose or music was used alone. Recorded music in isolation had a similar effect to the current gold standard of oral sucrose. www.anzctr.org.au ACTRN12615000271505. Copyright © 2017 Elsevier Inc. All rights reserved.

Antioxidant and Anti-Osteoporosis Activities of Chemical Constituents of the Stems of Zanthoxylum piperitum

Directory of Open Access Journals (Sweden)

Seo Young Yang

2018-02-01

Full Text Available Two new lignans, zanthoxyloside C (1 and zanthoxyloside D (2, together with nine known compounds comprising lignans (3–5, flavonoids (6–8, and phenolics (9–11, were isolated from the methanol extract of the stems of Zanthoxylum piperitum. All isolates were evaluated for their antioxidant and anti-osteoporotic activities using oxygen radical absorbance capacity (ORAC, cupric reducing antioxidant capacity (CUPRAC, and tartrate-resistant acid phosphatase (TRAP assays. Compounds 7–10 showed peroxyl radical-scavenging capacities and 4, 6–7, and 9 showed reducing capacities. Moreover, compounds 3, 6–9, and 11 significantly suppressed TRAP activities. These results indicated that the stems of Z. piperitum could be an excellent source for natural antioxidant and anti-osteoporosis.

Pattern Of Skin Prick Allergy Test Results In Enugu | Mgbor ...

African Journals Online (AJOL)

In this study we report on pattern of allergy prick skin test results found among atopic patients attending the department of otorhinolargngology of the University of Nigeria Teaching Hospital Enugu and Hansa Clinics, Enugu and propose ways of minimizing the exposure of the population to allergens. Material and method

Chemical analysis of nutritional content of prickly pads (Opuntia ficus indica) at varied ages in an organic harvest.

Science.gov (United States)

Hernández-Urbiola, Margarita I; Pérez-Torrero, Esther; Rodríguez-García, Mario E

2011-05-01

Opuntia ficus indica, also known as prickly pads, are an important part of the human diet and are also used as forage for livestock. This is an interesting vegetable due the environmental conditions in which it grows and its resistance to climatic extremes; however, little is known about its nutritional properties, especially in the later stages of maturity. The objective of this study was to determine the composition of organic prickly pads (Opuntia ficus indica) at differing stages of growth maturity. Chemical proximate analysis and mineral constituent analysis at different maturation stages were carried out in this investigation. As a result, older prickly pads were found to be an important source of nutritional components such as calcium.

Compatibility of Clinical Manifestation with Skin Prick Test Result and Food Provocation Test in Food Cross Reaction

OpenAIRE

Lubis, Azwin; Barlianto, Wisnu; Endaryanto, Anang; Harsono, Ariyanto

2017-01-01

Background: Subjective diagnostic test of food allergy is hugely biased, resulting in irrational diet avoidance. Additional objective tools by skin prick test following food provocation test resulting more accurate cause and prevalence on population. Purpose: To evaluate the compatibility of clinical symptoms with skin prick test and provocation test for imunoglobulin E (IgE) mediated food allergy in Dr. Soetomo Hospital Surabaya. Methods: Cross sectional observational analytic study. Patient...

Rehabilitation of Degraded Rangeland in Drylands by Prickly Pear (Opuntia ficus-indica L. Plantations: Effect on Soil and Spontaneous Vegetation

Directory of Open Access Journals (Sweden)

Souad Neffar

2013-12-01

Full Text Available In arid and semi-arid lands, the spiny prickly pear (Opuntia ficus-indica is an outstanding plant for soil conservation and restoration. To determine the role of Opuntia ficus-indica on vegetation recovery process in desertified areas of Southern Tebessa (Northeast Algeria, we investigated the effect of prickly pear plantation age and some soil properties (grain size, pH, electrical conductivity, organic matter, total nitrogen, available phosphorus, and CaCO3 equivalents on native plant community. Vegetation cover and plant diversity were assessed by calculating the number of individual plants (N, species richness (S, their ratio (N/S, Shannon index, and Evenness in prickly pear plantation plots of different ages (control, 5 and 20 years. Even if surveyed soil parameters did not differ significantly among O. ficus-indica plantations, results of ANOVA testing the effect of Opuntia plantations on native vegetation traits revealed significant variation for plant abundance (P < 0.0001, N/S ratio (P = 0.003 and vegetation cover (P < 0.0001. Vegetation cover differed significantly with both prickly-pear plantation age (P = 0.031 and seasons (P = 0.019. Tukey's tests revealed that all vegetation traits were significantly higher on prickly pear plantations than in control plots. Multiple comparisons also showed that plant abundance, N/S ratio and vegetation cover were significantly different between both young and old plantations and the controls. Prickly pear cultures facilitated the colonization and development of herbaceous species by ameliorating the severe environmental conditions. In conclusion, the facilitative effect of O. ficus-indica has been clearly demonstrated for both abundance and cover of native vegetation.

Ergonomic evaluation of conventional and improved methods of aonla pricking with women workers.

Science.gov (United States)

Rai, Arpana; Gandhi, Sudesh; Sharma, D K

2012-01-01

Conventional and improved methods of aonla pricking were evaluated ergonomically on an experiment conducted for 20 minute with women workers. The working heart rate, energy expenditure rate, total cardiac cost of work and physiological cost of work with conventional tools varied from 93-102 beats.min-1, 6-7.5 kJ.min-1, 285-470 beats, 14 -23 beats.min-1 while with machine varied from 96-105 beats.min-1, 6.5-8 kJ.min-1 , 336-540 beats, 16-27 beats.min-1 respectively. OWAS score for conventional method was 2 indicating corrective measures in near future while with machine was 1 indicating no corrective measures. Result of Nordic Musculoskeletal Questionnaire revealed that subjects complaint of pain in back, neck, right shoulder and right hand due to unnatural body posture and repetitive movement with hand tool. Moreover pricking was carried out in improper lighting conditions (200-300 lux) resulting into finger injuries from sharp edges of hand tool, whereas with machine no such problems were observed. Output with machine increased thrice than hand pricking in a given time. Machine was found useful in terms of saving time, increased productivity, enhanced safety and comfort as involved improved posture, was easy to handle and operate, thus increasing efficiency of the worker leading to better quality of life.

[Observation of curative effect of herpes zoster treated with acupuncture based on syndrome differentiation combined with pricking and cupping].

Science.gov (United States)

Pan, Hua

2011-10-01

To compare the differences of curative effects of herpes zoster treated with acupuncture based on syndrome differentiation combined with pricking and cupping and simple pricking and cupping. Eighty-six cases were randomly divided into an observation group (43 cases) and a control group (43 cases). In observation group, acupoints selection based on syndrome differentiation i.e. Quchi (LI 11), Zusanli (ST 36), Sanyinjiao (SP 6), etc. were selected and pricking and cupping at affected parts were applied, and the cases were classified into damp heat in liver and gallbladder, damp retention and spleen deficiency, and qi deficiency and blood stasis. In control group, all the cases were simplely treated with pricking and cupping at affected parts. The treatment was given once a day, and seven days were made one session. The curative effect was evaluated after 2 courses, and the follow-up was carried on after 1 month. The cured and markedly effective rate was 93.0% (40/43) in observation group, superior to that of 67.4% (29/43) in control group (P 0.05). The cured and markedly effective rate of damp retention and spleen deficiency: 93.8% (15/16) in observation group, superior to that of 60.0% (9/15) in control group (P cupping therapy is high pertinent and effective, the postherpetic neuralgia can be reduced significantly and the curative effect is superior to that of simple pricking and cupping.

Bioactivity of proteins isolated from Lactobacillus plantarum L67 treated with Zanthoxylum piperitum DC glycoprotein.

Science.gov (United States)

Song, S; Oh, S; Lim, K-T

2015-06-01

Lactobacilli in the human gastrointestinal tract have beneficial effects on the health of their host. To enhance these effects, the bioactivity of lactobacilli can be fortified through exogenous dietary or pharmacological agents, such as glycoproteins. To elucidate the inductive effect of Zanthoxylum piperitum DC (ZPDC) glycoprotein on Lactobacillus plantarum L67, we evaluated the radical-scavenging activity, anti-oxidative enzymes (SOD, GPx and CAT), growth rate, ATPase activity and β-galactosidase activity of this strain. When Lact. plantarum L67 was treated with ZPDC glycoprotein at different concentrations, the intensities of a few SDS-PAGE bands were slightly changed. The amount of a 23 kDa protein was increased upon treatment with increasing concentrations of ZPDC glycoprotein. The results of this study indicate that the radical-scavenging activity for O2(-) and OH¯, but not for the DPPH radical, increased in a concentration-dependent manner after treatment with ZPDC glycoprotein. The activation of anti-oxidative enzymes (SOD, GPx and CAT), growth rate and β-galactosidase activity also increased in a concentration-dependent manner in response to ZPDC glycoprotein treatment, whereas ATPase activity was decreased. In summary, ZPDC glycoprotein stimulated an increase in the bioactivity of Lact. plantarum L67. Significance and impact of the study: This study demonstrated that Lactobacillus plantarum L67 possesses anti-oxidative activity. This strain of lactic bacteria has been known to have various probiotic uses, such as yogurt starters and dietary additional supplements. We found, through this experiment, that the protein has a strong anti-oxidative character, and the activity can be enhanced by treatment with Zanthoxylum piperitum DC (ZPDC) glycoprotein. This study may be application of Lact. plantarum L67 treated by ZPDC glycoprotein in yogurt fermentation. It could be one of the avenues of minimizing yogurt postacidification during storage. In addition

Knowledge of parents regarding newborn screening test, after accessing the website “Babies’ Portal” - Heel prick test

Directory of Open Access Journals (Sweden)

Caroline Antonelli Mendes

Full Text Available ABSTRACT Purpose: to assess the knowledge of mothers about the heel prick test, develop contents on this test to make it available on the "Babies’ Portal" website, evaluate and validate the informative material developed. Methods: this study was conducted in three stages, that is, the first stage which is about a descriptive study involving 105 mothers of newborn children before performing the neonatal screening "Heel Prick Test", the second one consisting in the development of the website "Babies’ Portal", and the third stage, the evaluation and validation of this material carried out by 20 parents of children between zero and 36 months old, who underwent the neonatal screening Heel Prick Test by accessing the website “Babies’ Portal”. Results: although the interviewed mothers knew that their children had the right to be tested, they showed no knowledge of the diseases that can be prevented, time of diagnosis, nor the consequences arising from the lack of early diagnosis and treatment. The website creation and validation gathered basic information about the Heel Prick Test, and the participants regarded the content from satisfactory to excellent. Conclusion: it is necessary that families know not only about the procedures their children will undergo, but also the reason they are performed and the consequences of failing in doing so.

Food allergies in children: a comparison of parental reports and skin prick test results

Directory of Open Access Journals (Sweden)

Camilia Metadea Aji Savitri

2018-04-01

Full Text Available Background Food allergy is common in children and its prevalence is generally on the rise. Imprecise parental reports about reactions to particular foods can lead to unnecessary restrictions. Since children have specific growth requirements, such nutritional restrictions may have disturbing effects on children’s growth and development. Objective To compare parental reports on food reactions to skin prick test results in their children. Method Retrospective, cross sectional study using patient’s medical record data during one-year study period. Data were analyzed manually and statistically, to assess the degree of agreement (Kappa’s coefficient and significance (P. Results We collected data from 154 subjects aged 0-18 years. For every allergen assessed, parents reported more food reactions than positive skin prick test results. Allergy incidence were caused, in order, by cow’s milk and chicken (25.3%, eggs (22.1%, chocolate (20.1%, fruits (14.3%, seafood (13%, and saltwater fish (1.9%. Kappa coefficient are all poor (0.05 except for chicken (P=0.02. Conclusion Most parents tend to overestimate which food cause reactions in their children, as reactions reported were not necessarily allergenic. Therefore, every patient experiencing allergy reactions should undergo skin prick testing to confirm the possibility of allergy.

Protecting black ash from the emerald ash borer

Science.gov (United States)

Les Benedict

2010-01-01

Black ash (Fraxinus nigra) is an important resource for Tribes in the Northeast and Great Lakes regions of the North American continent. Ash in North America is being threatened with widespread destruction as a result of the introduction of emerald ash borer beetle (Agrilus planipennis) in 2002. Measures are being taken to slow the spread of emerald ash borer beetle....

Sensitivity Comparison of the Skin Prick Test and Serum and Fecal Radio Allergosorbent Test (RAST in Diagnosis of Food Allergy in Children

Directory of Open Access Journals (Sweden)

Hamid Reza Kianifar

2016-05-01

Full Text Available Background: Diagnosis of food allergy is difficult in children. Food allergies are diagnosed using several methods that include medical histories, clinical examinations, skin prick and serum-specific immunoglobulin E (IgE tests, radio-allergosorbent test (RAST, food challenge, and supervised elimination diets. In this study we evaluated allergies to cow's milk, egg, peanut, and fish in children with suspected food allergies with skin prick tests and serum and feces RAST. Methods: Forty-one children with clinical symptoms of food allergies were enrolled in the study. Skin prick tests and serum and fecal RAST were performed and compared with challenge tests. Results: The most common sites of food allergy symptoms were gastrointestinal (82.9% and skin (48.8%. 100% of the patients responded to the challenge tests with cow’s milk, egg, peanut, and fish. 65% of the patients tested positive with the skin prick test, 12.1% tested positive with serum RAST, and 29.2% tested positive with fecal RAST. Conclusions: The skin prick test was more sensitive than serum or fecal RAST, and fecal RAST was more than twice as sensitive as serum RAST.

Anesthetic constituents of Zanthoxylum bungeanum Maxim.: A pharmacokinetic study.

Science.gov (United States)

Rong, Rong; Cui, Mei-Yu; Zhang, Qi-Li; Zhang, Mei-Yan; Yu, Yu-Ming; Zhou, Xian-Ying; Yu, Zhi-Guo; Zhao, Yun-Li

2016-07-01

A sensitive and selective ultra high performance liquid chromatography with tandem mass spectrometry method was established and validated for the simultaneous determination of hydroxy-α-sanshool, hydroxy-β-sanshool, and hydroxy-γ-sanshool in rat plasma after the subcutaneous and intravenous administration of an extract of the pericarp of Zanthoxylum bungeanum Maxim. Piperine was used as the internal standard. The analytes were extracted from rat plasma by liquid-liquid extraction with ethyl acetate and separated on a Thermo Hypersil GOLD C18 column (2.1 mm × 50 mm, 1.9 μm) with a gradient elution system at a flow rate of 0.4 mL/min. The mobile phase consisted of acetonitrile/0.05% formic acid in water and the total analysis time was 4 min. Positive electrospray ionization was performed using multiple reaction monitoring mode for the analytes. The calibration curves of the three analytes were linear over the tested concentration range. The intra- and interday precision was no more than 13.6%. Extraction recovery, matrix effect, and stability were satisfactory in rat plasma. The developed and validated method was suitable for the quantification of hydroxy-α-sanshool, hydroxy-β-sanshool, and hydroxy-γ-sanshool and successfully applied to a pharmacokinetic study of these analytes after subcutaneous and intravenous administration to rats. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Preventing the dental needle prick injury (DNPI) : a new approach to ...

African Journals Online (AJOL)

The burden of serious occupational hazards of infectious diseases such as HIV, Hepatitis B and C, Lassa and Ebola Virus diseases which can be contracted through such injuries can be quite costly to the dental health care worker and to the healthcare system in general. Dental needle prick injury (DNPI) prevention devices ...

Thin layer convective solar drying and mathematical modeling of prickly pear peel (Opuntia ficus indica)

International Nuclear Information System (INIS)

Lahsasni, Siham; Kouhila, Mohammed; Mahrouz, Mostafa; Idlimam, Ali; Jamali, Abdelkrim

2004-01-01

This paper presents the thin layer convective solar drying and mathematical modeling of prickly pear peel. For these purposes, an indirect forced convection solar dryer consisting of a solar air collector, an auxiliary heater, a circulation fan and a drying cabinet is used for drying experiments. Moreover, the prickly pear peel is sufficiently dried in the ranges of 32 to 36 deg. C of ambient air temperature, 50 to 60 deg. C of drying air temperature, 23 to 34% of relative humidity, 0.0277 to 0.0833 m 3 /s of drying air flow rate and 200 to 950 W/m 2 of daily solar radiation. The experimental drying curves show only a falling drying rate period. The main factor in controlling the drying rate was found to be the drying air temperature. The drying rate equation is determined empirically from the characteristic drying curve. Also, the experimental drying curves obtained were fitted to a number of mathematical models. The Midilli-Kucuk drying model was found to satisfactorily describe the solar drying curves of prickly pear peel with a correlation coefficient (r) of 0.9998 and chi-square (χ 2 ) of 4.6572 10 -5

In vitro and in vivo characterization of hazelnut skin prick test extracts

NARCIS (Netherlands)

Akkerdaas, Jaap H.; Wensing, Marjolein; Knulst, André C.; Aalberse, Rob C.; Hefle, Susan L.; van Ree, Ronald

2003-01-01

RATIONALE: Hazelnut allergy ranks among the most frequently observed food allergies. Clinical symptoms range from the oral allergy syndrome to life threatening anaphylaxis. Diagnosis of hazelnut allergy partially relies on in vivo testing by means of skin prick testing (SPT). The aim of this study

Chemical composition and larvicidal activity of Zanthoxylum armatum against diamondback moth, Plutella xylostella.

Science.gov (United States)

Kumar, Vishal; Reddy, S G Eswara; Chauhan, Urvashi; Kumar, Neeraj; Singh, Bikram

2016-01-01

The diamondback moth, Plutella xylostella (L.) (Lepidoptera: Yponomeutidae) is the most serious pest of cruciferous crops grown in the world causing economic yield loss. Several synthetic insecticides have been used against P. xylostella but satisfactory control was not achieved due to development of resistance to insecticides. Therefore, the present study was carried out to screen different fractions of Zanthoxylum armatum for their insecticidal activities against second instar larvae of P. xylostella. Results indicate, all the fractions showed activity to P. xylostella. However, n-hexane fraction of Z. armatum showed maximum larvicidal activity with minimum LC50 value of 2988.6 ppm followed by ethanol (LC50 = 12779.7 ppm) and methanol fraction (LC50 = 12908.8 ppm) whereas chloroform fraction was least toxic (LC50 = 16750.6 ppm). The GC-MS analysis of n-hexane fraction of leaf extract showed maximum larvicidal activity, which may be due to two major compounds i.e. 2-undecanone (19.75%) and 2-tridecanone (11.76%).

Engineering Behavior and Characteristics of Wood Ash and Sugarcane Bagasse Ash

Directory of Open Access Journals (Sweden)

Francisco Grau

2015-10-01

Full Text Available Biomasses are organic materials that are derived from any living or recently-living structure. Plenty of biomasses are produced nationwide. Biomasses are mostly combusted and usually discarded or disposed of without treatment as biomass ashes, which include wood and sugarcane bagasse ashes. Thus, recycling or treatment of biomass ashes leads to utilizing the natural materials as an economical and environmental alternative. This study is intended to provide an environmental solution for uncontrolled disposal of biomass ashes by way of recycling the biomass ash and replacing the soils in geotechnical engineering projects. Therefore, in this study, characteristic tests of wood and sugarcane bagasse ashes that are considered the most common biomass ashes are conducted. The test of chemical compositions of biomass ashes is conducted using energy dispersive X-ray spectroscopy (EDS, and Scanning Electron Microscope (SEM, and heavy metal analysis is also conducted. Engineering behaviors including hydraulic conductivity, constrained modulus and shear modulus are examined. Also, coal fly ash Class C is used in this study for comparison with biomass ashes, and Ottawa 20/30 sands containing biomass ashes are examined to identify the soil replacement effect of biomass ashes. The results show that the particle sizes of biomass ashes are halfway between coal fly ash Class C and Ottawa 20/30 sand, and biomass ashes consist of a heterogeneous mixture of different particle sizes and shapes. Also, all heavy metal concentrations were found to be below the US Environmental Protection Agency (EPA maximum limit. Hydraulic conductivity values of Ottawa 20/30 sand decrease significantly when replacing them with only 1%–2% of biomass ashes. While both the constrained modulus and shear modulus of biomass ashes are lower than Ottawa 20/30 sand, those of mixtures containing up to 10% biomass ashes are little affected by replacing the soils with biomass ashes.

Adsorption-desorption isotherms and heat of sorption of prickly pear fruit (Opuntia ficus indica)

International Nuclear Information System (INIS)

Lahsasni, S.; Kouhila, M.; Mahrouz, M.

2004-01-01

The equilibrium moisture contents were determined for prickly pear fruit using the gravimetric static method at t=30, 40 and 50 deg. C over a range of relative humidities from 0.05 to 0.9. The sorption curves of prickly pear fruit decreased with increase in temperature at constant relative humidity. The hysteresis effect was observed. The GAB, modified Halsey, modified Chung-Pfost, modified Oswin and modified Henderson models were tested to fit the experimental data. The GAB model was found to be the most suitable for describing the sorption curves. The monolayer moisture content values for the sorption at different temperatures are calculated using a modified BET equation. The isosteric heats of desorption and adsorption of water were determined from the equilibrium data at different temperatures

Adsorption-desorption isotherms and heat of sorption of prickly pear fruit (Opuntia ficus indica)

Energy Technology Data Exchange (ETDEWEB)

Lahsasni, S.; Kouhila, M. E-mail: kouhila@hotmail.com; Mahrouz, M

2004-01-01

The equilibrium moisture contents were determined for prickly pear fruit using the gravimetric static method at t=30, 40 and 50 deg. C over a range of relative humidities from 0.05 to 0.9. The sorption curves of prickly pear fruit decreased with increase in temperature at constant relative humidity. The hysteresis effect was observed. The GAB, modified Halsey, modified Chung-Pfost, modified Oswin and modified Henderson models were tested to fit the experimental data. The GAB model was found to be the most suitable for describing the sorption curves. The monolayer moisture content values for the sorption at different temperatures are calculated using a modified BET equation. The isosteric heats of desorption and adsorption of water were determined from the equilibrium data at different temperatures.

[Characteristics of allergic conjunctivitis with positive skin prick test].

Science.gov (United States)

Yang, S; Jiang, Y; Jin, Y M; Zhang, J Y; Li, Y

2017-09-11

Objective: To observe the clinical characteristics of allergic conjunctivitis, and the correlations with skin prick test results. Methods: A retrospective study. Forty patients with positive skin prick test result were included. Patients underwent an ophthalmologic examination to identify their primary presenting signs and symptoms. The allergy types were divided into 5 groups. All dates were analyzed for the dependence, normality and homogeneity of variance. Chi-square test, Mann-Whitney U test, Kruskal-Wallis H test and Spearman correlation analysis were performed accordingly. Results: Among 40 patients, 18(45.0%) had a clinical diagnosis of seasonal allergic conjunctivitis, 14(35.0%) had perennial allergic conjunctivitis, 5(12.5%) had vernal keratoconjunctivitis, and 2(5.0%) had atopic keratoconjunctivits, and 1(2.5%) had giant papillary conjunctivitis. There was no significant difference in the number of symptoms and signs score among different types of allergic conjunctivitis, the score of itching and hyperemia had a positive relationship with the number of positive allergens ( r =0.74, Ptest of the allergen, the more symptoms and signs encountered in terms of severity. Conclusion: Seasonal allergic conjunctivitis was the most prevalent disorder, the most important clinical characteristics of allergic conjunctivitis are itching and conjunctival congestion, the main allergens are dust and pollens, patients may be sensitive to multiple allergens. (Chin J Ophthalmol, 2017, 53: 689-693) .

Ash Utilisation 2012. Ashes in a Sustainable Society. Proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-11-01

Conference themes: Risk assessment, Fly ash- Road construction, Recycling and Greenhouse gases, Storage of ashes, Fertilizer, Metal Mining, Support and Barriers, Construction Material, Civil Engineering, and MSWI bottom ash.

Performance and Pain Tolerability of Current Diagnostic Allergy Skin Prick Test Devices.

Science.gov (United States)

Tversky, Jody R; Chelladurai, Yohalakshmi; McGready, John; Hamilton, Robert G

2015-01-01

Allergen skin prick testing remains an essential tool for diagnosing atopic disease and guiding treatment. Sensitivity needs to be defined for newly introduced devices. Our aim was to compare the performance of 10 current allergy skin prick test devices. Single- and multiheaded skin test devices (n = 10) were applied by a single operator in a prospective randomized manner. Histamine (1 and 6 mg/mL) and control diluent were introduced at 6 randomized locations onto the upper and lower arms of healthy subjects. Wheal and flare reactions were measured independently by 2 masked technicians. Twenty-four subjects provided consent, and 768 skin tests were placed. Mean wheal diameter among devices differed from 3.0 mm (ComforTen; Hollister-Stier, Spokane, Wash) to 6.8 mm (UniTest PC; Lincoln Diagnostics, Decatur, Ill) using 1 mg/mL histamine (P Diagnostics, Decatur, Ill; and Sharp-Test; Panatrex, Placentia, Calif) using 6 mg/mL histamine (P pain score of less than 4 on a 10-point visual analog scale. Pain scores were higher among women, but this did not reach statistical significance. The Multi-Test PC and the UniTest PC had the lowest pain scores compared with the other devices. All 10 skin prick test devices displayed good analytical sensitivity and specificity; however, 3 mm cannot arbitrarily be used as a positive threshold. The use of histamine at 1 mg/mL is unacceptable for certain devices but may be preferable for the most sensitive devices. On average, there was no pain score difference between multiheaded and single-head devices. Copyright © 2015 American Academy of Allergy, Asthma & Immunology. Published by Elsevier Inc. All rights reserved.

Thin layer convective solar drying and mathematical modeling of prickly pear peel (Opuntia ficus indica)

Energy Technology Data Exchange (ETDEWEB)

Lahsasni, S.; Mahrouz, M. [Unite de Chimie Agroalimentaire (LCOA), Faculte des Sciences Semlalia, Marrakech (Morocco); Kouhila, M.; Idlimam, A.; Jamali, A. [Ecole Normale Superieure, Marrakech (Morocco). Lab. d' Energie Solaire et Plantes Aromatiques et Medicinales

2004-02-01

This paper presents the thin layer convective solar drying and mathematical modeling of prickly pear peel. For these purposes, an indirect forced convection solar dryer consisting of a solar air collector, an auxiliary heater, a circulation fan and a drying cabinet is used for drying experiments. Moreover, the prickly pear peel is sufficiently dried in the ranges of 32 to 36 {sup o} C of ambient air temperature, 50 to 60 {sup o}C of drying air temperature, 23 to 34% of relative humidity, 0.0277 to 0.0833 m{sup 3}/s of drying air flow rate and 200 to 950 W/m{sup 2} of daily solar radiation. The experimental drying curves show only a falling drying rate period. The main factor in controlling the drying rate was found to be the drying air temperature. The drying rate equation is determined empirically from the characteristic drying curve. Also, the experimental drying curves obtained were fitted to a number of mathematical models. The Midilli-Kucuk drying model was found to satisfactorily describe the solar drying curves of prickly pear peel with a correlation coefficient (r) of 0.9998 and chi-square ({chi}{sup 2}) of 4.6572 10{sup -5}. (Author)

Biomass ash utilization

Energy Technology Data Exchange (ETDEWEB)

Bristol, D.R.; Noel, D.J.; O`Brien, B. [HYDRA-CO Operations, Inc., Syracuse, NY (United States); Parker, B. [US Energy Corp., Fort Fairfield, ME (United States)

1993-12-31

This paper demonstrates that with careful analysis of ash from multiple biomass and waste wood fired power plants that most of the ash can serve a useful purpose. Some applications require higher levels of consistency than others. Examples of ash spreading for agricultural purposes as a lime supplement for soil enhancement in Maine and North Carolina, as well as a roadbase material in Maine are discussed. Use of ash as a horticultural additive is explored, as well as in composting as a filtering media and as cover material for landfills. The ash utilization is evaluated in a framework of environmental responsibility, regulations, handling and cost. Depending on the chemical and physical properties of the biomass derived fly ash and bottom ash, it can be used in one or more applications. Developing a program that utilizes ash produced in biomass facilities is environmentally and socially sound and can be financially attractive.

Cytotoxic evaluation of essential oil from Zanthoxylum rhoifolium Lam. leaves Avaliação citotóxica do óleo volátil extraído das folhas do Zanthoxylum rhoifolium Lam.

Directory of Open Access Journals (Sweden)

Saulo Luis da Silva

2007-06-01

Full Text Available Zanthoxylum rhoifolium Lam is a plant popularly used as antimicrobial, for malaria and inflammatory treatment. The essential oil of Z. rhoifolium was extracted and its cytotoxic effects against HeLa (human cervical carcinoma, A-549 (human lung carcinoma, HT-29 (human colon adenocarcinoma, Vero (monkey kidney cell lines and mice macrophages were evaluated. Some of the terpenes of its essential oil (ß-caryophyllene, alpha-humulene, alpha -pinene, myrcene and linalool were also tested to verify their possible influence in the oil cytotoxic activity. The results obtained permitted to confirm that the essential oil is cytotoxic against tumoral cells (CD50 = 82.3, 90.7 and 113.6 µg/ml for A-549, HeLa e HT-29 cell lines, respectively, while it did not show cytotoxicity against non-tumoral cells (Vero and mice macrophages. Thus, the essential oil from Z. rhoifolium leaves seems to present a possible therapeuthic role due to its selective cytotoxic activity against tumoral cell lines.O Zanthoxylum rhoifolium Lam. é uma planta popularmente utilizada como antimicrobianos, no tratamento da malária e de inflamações. O óleo volátil do Z. rhoifolium foi extraído e posteriormente foi avaliada a sua citotoxicidade contra células HeLa (carcinoma cervical humano, A-549 (carcinoma de pulmão humano, HT-29 (adenocarcinoma de cólon humano, Vero (rim de macaco e macrófagos de camundongos. Alguns terpenos constituintes do óleo volátil (beta-cariofileno, alfa -humuleno, alfa -pineno, mirceno e linalool também foram testados para verificar as possíveis influências sobre a citotoxicidade do óleo. Os resultados obtidos permitiram verificar que o óleo volátil é citotóxico contra células as tumorais (CD50 = 82.3, 90.7 e 113.6 µg/ml para A-549, HeLa e HT-29 cell lines, respectivamente, mas não apresenta citotoxicidade contra as células não tumorais (Vero e macrófagos de camundongos. Desta forma o óleo volátil das folhas do Z. rhoifolium demonstra

Phytochemical study of prickly pear from southern Morocco

Directory of Open Access Journals (Sweden)

Z. Bouzoubaâ

2016-06-01

Full Text Available This work concerns the phytochemical study of the prickly pear pulp’s fruits of two opuntia cultivars; Achefri and Amouslem widely present in two regions of southern Morocco; Arbaa Sahel and Asgherkis that are different in their altitude and annual rainfall. The results of the phytochemical study show that the levels of antioxidants have a non-significant difference between the fruits of the two sites (comparing Amouslem and Achefri in the same site, on the one hand, for the differences due to the variety or cultivar, on the other hand between Amouslem and Achefri from the two sites to show the site effect.

Atividade anti-helmíntica do extrato aquoso das folhas de Zanthoxylum rhoifolium Lam. (Rutaceae Anthelmintic activity of aqueous extract of Zanthoxylum rhoifolium Lam. leaves (Rutaceae

Directory of Open Access Journals (Sweden)

Peneluc Taíse

2009-12-01

Full Text Available O estudo avaliou a atividade anti-helmíntica do extrato aquoso das folhas de Zanthoxylum rhoifolium em dois experimentos. O teste in vitro utilizou cultivos de fezes de caprinos tratados com diferentes concentrações do extrato: (134,5 a 335,0 mg.mL-1. No teste in vivo, utilizaram-se 20 ovelhas: G1 tratado durante quatro dias (0,63 g.kg-1 PV; G2, mesma dose, por oito dias; G3, ivermectina (200 μg.kg-1; e G4, sem tratamento. In vitro, observou-se redução de larvas de Haemonchus, Trichostrongylus e Oesophagostomum superior a 95% nas concentrações de 193,7 a 335,0 mg.mL-1. In vivo, a redução de ovos por grama de fezes foi de 51, 56 e 90%, respectivamente, para G1, G2 e G3, no oitavo dia de tratamento, enquanto para os estágios imaturos e adultos variou de 0 a 91% no G1 e 26 a 94% no G2. A eficácia da ivermectina alcançou 99% para L4 e L5 de H. contortus e 100% para as demais espécies de nematoides. Parâmetros clínicos e bioquímicos permaneceram na faixa de normalidade, e as análises histopatológicas não revelaram alterações sugestivas de toxicidade. Embora altamente efetivo in vitro, o extrato aquoso de folhas de Z. rhoifolium foi pouco eficaz in vivo na redução de nematoides gastrintestinais.The study evaluated the anthelmintic activity of aqueous extract of Zanthoxylum rhoifolium leaves in two experiments. In vitro test, cultures of goat fecal samples were treated with different concentrations of extract (134.5 to 335.0 mg.mL-1. In vivo test was composed of 20 sheep: G1: treated with 0.63 g.kg-1, during four days; G2: same dose, for eight days; G3: ivermectin (200 μg.kg-1 and G4 untreated group. In vitro results showed a reduction of Haemonchus spp, Trichostrongylus spp. and Oesophagostomum spp. larvae greater than 95% in the concentrations between 335.0 and 193.7 mg.mL-1. Faecal egg counting reduction was 51, 56 and 90% in G1, G2 and G3, respectively, while immature stages and adults ranged from 0 to 91% in G1 and from 26

Development of novel ash hybrids to introgress resistance to emerald ash borer into north American ash species

Science.gov (United States)

Jennifer L. Koch; David W. Carey; Mary E. Mason

2008-01-01

Currently, there is no evidence that any of the native North American ash species have any resistance to the emerald ash borer (EAB). This means that the entire ash resource of the eastern United States and Canada is at risk of loss due to EAB. In contrast, outbreaks of EAB in Asian ash species are rare and appear to be isolated responses to stress (Bauer et al. 2005,...

Effect of Mozart music on heel prick pain in preterm infants: a pilot randomized controlled trial

Directory of Open Access Journals (Sweden)

Cristina Cavaiuolo

2015-02-01

Full Text Available Objective: The aim of this pilot study was to determine the effect of music by Mozart on heel prick procedural pain in premature infants.Background: Painful procedures are routinely performed in the setting of neonatal intensive care unit (NICU. Pain may exert short- and long-term deleterious effects on premature babies. Many non-pharmacological interventions have been proven efficacious for blunting neonatal pain.Study design: Randomized, controlled trial.Methods: The study was carried out in the NICU of the “G. Rummo” Hospital in Benevento, Italy. The sample consisted of 42 preterm infants, with no hearing loss or significant cerebral lesions on cranial ultrasound. They were randomized to receive heel lance during a music condition or a no-music control condition. We set strict criteria for selecting and delivering the music. Baseline and postprocedural heart rate and transcutaneous oxygen saturation were manually recorded. The Premature Infant Pain Profile (PIPP score was used to measure the behavioral response to prick. An unpaired t-test was performed for the intergroup comparisons.Results: There were significant differences between groups on heart rate increase, oxygen saturation reduction and PIPP score following the procedure.Conclusions: Listening to Mozart music during heel prick is a simple and inexpensive tool for pain alleviating in preterm stable neonates.

Silica from Ash

Indian Academy of Sciences (India)

management, polymer composites and chemical process design. Figure 1 Difference in color of the ash ... The selection of ash is important as the quality of ash determines the total amount as well as quality of silica recoverable Ash which has undergone maximum extent of combustion is highly desirable as it contains ...

Hurdle technology applied to prickly pear beverages for inhibiting Saccharomyces cerevisiae and Escherichia coli.

Science.gov (United States)

García-García, R; Escobedo-Avellaneda, Z; Tejada-Ortigoza, V; Martín-Belloso, O; Valdez-Fragoso, A; Welti-Chanes, J

2015-06-01

The effect of pH reduction (from 6·30-6·45 to 4·22-4·46) and the addition of antimicrobial compounds (sodium benzoate and potassium sorbate) on the inhibition of Saccharomyces cerevisiae and Escherichia coli in prickly pear beverages formulated with the pulp and peel of Villanueva (V, Opuntia albicarpa) and Rojo Vigor (RV, Opuntia ficus-indica) varieties during 14 days of storage at 25°C, was evaluated. RV variety presented the highest microbial inhibition. By combining pH reduction and preservatives, reductions of 6·2-log10 and 2·3-log10 for E. coli and S. cerevisiae were achieved respectively. Due to the low reduction of S. cerevisiae, pulsed electric fields (PEF) (11-15 μs/25-50 Hz/27-36 kV cm(-1)) was applied as another preservation factor. The combination of preservatives, pH reduction and PEF at 13-15 μs/25-50 Hz for V variety, and 11 μs/50 Hz, 13-15 μs/25-50 Hz for RV, had a synergistic effect on S. cerevisiae inhibition, achieving at least 3·4-log10 of microbial reduction immediately after processing, and more than 5-log10 at fourth day of storage at 25°C maintained this reduction during 21 days of storage (P > 0·05). Hurdle technology using PEF in combination with other factors is adequate to maintain stable prickly pear beverages during 21 days/25°C. Significance and impact of the study: Prickly pear is a fruit with functional value, with high content of nutraceuticals and antioxidant activity. Functional beverages formulated with the pulp and peel of this fruit represent an alternative for its consumption. Escherichia coli and Saccharomyces cerevisiae are micro-organisms that typically affect fruit beverage quality and safety. The food industry is looking for processing technologies that maintain quality without compromising safety. Hurdle technology, including pulsed electric fields (PEF) could be an option to achieve this. The combination of PEF, pH reduction and preservatives is an alternative to obtain safe and minimally processed

False deformation temperatures for ash fusibility associated with the conditions for ash preparation

Energy Technology Data Exchange (ETDEWEB)

Wall, T.F.; Gupta, S.K.; Gupta, R.P.; Sanders, R.H.; Creelman, R.A.; Bryant, G.W. [University of Newcastle, Callaghan, NSW (Australia). Cooperative Research Centre for Black Coal Utilization, Dept. of Chemical Engineering

1999-07-01

A study was made to investigate the fusibility behaviour of coal ashes of high ash fusion temperatures. Coals and ashes formed in the boiler were sampled in several Australian power stations, with laboratory ashes being prepared from the coals. The laboratory ashes gave lower values for the deformation temperature (DT) than the combustion ashes when the ash had low levels of basic oxide components. Thermo-mechanical analysis, quantitative X-ray diffraction and scanning electron microscopy were used to establish the mechanisms responsible for the difference. Laboratory ash is finer than combustion ash and it includes unreacted minerals (such as quartz, kaolinite and illite) and anhydrite (CaSO{sub 4}). Fusion events which appear to be characteristic of reacting illite, at temperatures from 900 to 1200{degree}C, were observed for the laboratory ashes, these being associated with the formation of melt phase and substantial shrinkage. The combustion ashes did not contain this mineral and their fusion events were observed at temperatures exceeding 1300{degree}C. The low DTs of coal ashes with low levels of basic oxides are therefore a characteristic of laboratory ash rather than that found in practical combustion systems. These low temperatures are not expected to be associated with slagging in pulverised coal fired systems. 10 refs., 3 figs., 2 tabs.

Wound-healing Activity of Zanthoxylum bungeanum Maxim Seed Oil on Experimentally Burned Rats.

Science.gov (United States)

Li, Xiao-Qiang; Kang, Rong; Huo, Jun-Cheng; Xie, Yan-Hua; Wang, Si-Wang; Cao, Wei

2017-01-01

The seed oil of Zanthoxylum bungeanum Maxim (ZBSO) is considered to be rich source of fatty acids, mainly oleic and linoleic acids, and has been used for the treatment of burns in Chinese medicine. We evaluated the healing efficacy of ZBSO and explored its possible mechanism on scalded rats. Sprague-Dawley rat models with deep second-degree burns were set up, and ZBSO (500 and 1000 μl/wound) was topically applied twice daily for 7 days and then once daily until wound healing. The therapeutic effects of ZBSO were evaluated by observing wound closure time, decrustation time, wound-healing ratio, and pathological changes. Collagen type-III, matrix metalloproteinase-2 (MMP-2), MMP-9, phospho-nuclear factor-κB (p-NF-κB) p65, inhibitor of NF-κB subunit α p-IκBα, and inhibitor of NF-κB subunit α (IκBα) expression were determined using Western blotting. The ZBSO-treated group showed a higher wound-healing ratio and shorter decrustation and wound closure times than the untreated group. The topical application of ZBSO increased collagen synthesis as evidenced by an increase in hydroxyproline level and upregulated expression of collagen type-III on days 7, 14, and 21 posttreatment. A reduction in MMP-2 and MMP-9 expressions also confirmed the collagen formation efficacy of ZBSO. Furthermore, there was a significant increase in superoxide dismutase levels and a decrease in malondialdehyde levels in ZBSO-treated wounds. ZBSO also decreased tumor necrosis factor alpha, interleukin-1 (IL-1) β, and IL-6 levels in serum, upregulated IκBα, and downregulated p-NF-κB p65 and p-IκBα expression in vivo , indicating the anti-inflammatory action of ZBSO. ZBSO has significant potential to treat burn wounds by accelerating collagen synthesis and the anti-inflammatory cascade of the healing process. The seed oil of Zanthoxylum bungeanum Maxim (ZBSO) is rich of fatty acidsThe healing efficacy of ZBSO on experimentally scalded rats was evaluatedZBSO has significant potential

Frozen fruit skin prick test for the diagnosis of fruit allergy.

Science.gov (United States)

Garriga, Teresa; Guilarte, Mar; Luengo, Olga; Guillén, Mercé; Labrador-Horrillo, Moisés; Fadeeva, Tatiana; Sala, Anna; Cardona, Victória

2010-12-01

Diagnosis of fruit sensitisation by skin prick test (SPT) is fast and easy to perform. Nevertheless, some fruit is not available throughout the year. Freezing aliquots of these fresh fruits to be defrosted would be a good solution to perform SPT at any time. To compare the reproducibility of SPT with Rosaceae and Cucurbitaceae frozen fruit with fresh and commercial fruit extracts. SPT with the following fruit were performed: apricot, cherry, strawberry, nectarine, Japanese medlar, peach, (peel and pulp), yellow and red plum, melon and watermelon. We compared fresh fruit, commercial extract and fruit which had been frozen at -18 degrees C. Results were read by planimetry (Inmunotek prick-film) after 15 minutes. The study group comprised 48 patients (9 males, 39 females) with a mean age of 31, 6 +/- 2.0 years. Concordance of positive and negative results was extremely high and significant in all cases. Correlation between frozen fruit and commercial extract, frozen fruit and fresh and commercial extract and fresh fruit was statistically significant in all cases except for strawberry. The use of frozen fruit is a valid method, as the performance of the SPT is similar to that of fresh fruit. This enables diagnostic procedures with seasonal fruit at any time of the year.

Cementing Efficiency of Low Calcium Fly Ash in Fly Ash Concretes

OpenAIRE

T. D. Gunneswara Rao; Mudimby Andal

2014-01-01

Research on the utilization of fly ash will no longer refer the fly ash as a waste material of thermal power plants. Use of fly ash in concrete making, makes the concrete economical as well as durable. The fly ash is being added to the concrete in three ways namely, as partial replacement to cement, as partial replacement to fine aggregates and as admixture. Addition of fly ash to the concrete in any one of the form mentioned above, makes the concrete more workable and durable than the conven...

Emerald ash borer biocontrol in ash saplings: the potential for early stage recovery of North American ash

Science.gov (United States)

In many parts of North America, ash stands have been reduced by the emerald ash borer (Agrilus planipennis) invasion to a few surviving mature trees and young basal sprouts, saplings, and seedlings. Without a seed bank, ash tree recovery will require survival and maturation of these younger cohorts...

Radioactivity of wood ash

International Nuclear Information System (INIS)

Rantavaara, A.; Moring, M.

2000-01-01

STUK (Finnish Radiation and Nuclear Safety Authority) has investigated natural and artificial radioactivity in wood ash and radiation exposure from radionuclides in ash since 1996. The aim was to consider both handling of ash and different ways of using ash. In all 87 ash samples were collected from 22 plants using entirely or partially wood for their energy production in 1996-1997. The sites studied represented mostly chemical forest industry, sawmills or district heat production. Most plants used fluidised bed combustion technique. Samples of both fly ash and bottom ash were studied. The activity concentrations of radionuclides in samples of, e.g., dried fly ash from fuel containing more than 80% wood were determined. The means ranged from 2000 to less than 50 Bq kg -1 , in decreasing order: 137 Cs, 40 K, 90 Sr, 210 Pb, 226 Ra, 232 Th, 134 Cs, 235 U. In bott radionuclide contents decreased in the same order as in fly ash, but were smaller, and 210 Pb was hardly detectable. The NH 4 Ac extractable fractions of activities for isotopes of alkaline elements (K, Cs) in bottom ash were lower than in fly ash, whereas solubility of heavier isotopes was low. Safety requirements defined by STUK in ST-guide 12.2 for handling of peat ash were fulfilled at each of the sites. Use of ash for land-filling and construction of streets was minimal during the sampling period. Increasing this type of ash use had often needed further investigations, as description of the use of additional materials that attenuate radiation. Fertilisation of forests with wood ash adds slightly to the external irradiation in forests, but will mostly decrease doses received through use of timber, berries, mushrooms and game meat. (orig.)

Identification of low allergenic apple cultivars using skin prick tests and oral food challenges.

Science.gov (United States)

Vlieg-Boerstra, B J; van de Weg, W E; van der Heide, S; Kerkhof, M; Arens, P; Heijerman-Peppelman, G; Dubois, A E J

2011-04-01

As oral allergy syndrome (OAS) symptoms to apple are frequent, we aimed to identify low allergenic apple cultivars and to validate the prick-to-prick skin prick test (SPT) as a suitable screening method. Sixty-eight apple cultivars were tested by SPTs in 33 Dutch adults with OAS, before and during the birch pollen season in 2006 and 2007, respectively. Three cultivars yielding the largest number of negative SPTs (Elise, Santana and Pink Lady®) and one reference cultivar (Golden Delicious) were subsequently tested by single-blind oral food challenges (SBFC) just after picking in fall 2007 (fresh) and in spring 2008 (stored), outside the birch pollen season and preceded by SPTs. In spring, Santana was replaced by Modi®. In fresh apples, OAS symptoms of Elise, as measured by cumulative scores on a Visual Analogue Scale VASt, were significantly lower than those of Santana, Pink Lady and Golden Delicious (P = 0.021; 0.040 and 0.005, respectively). VASt scores of Santana were significantly lower than those of Golden Delicious (P = 0.049). In stored apples, VASt scores of Elise were significantly lower than that of Golden Delicious (P = 0.038). VASt scores of fresh apples did not differ significantly from stored apples, except in Golden Delicious (spring < fall: P = 0.021). The SPTs did not predict the severity of OAS. SPTs are not useful to assess the allergenicity of apple cultivars. By using SBFC, Elise and Santana were identified as low allergenic apple cultivars in patient with OAS. Our data on the effect of storage are inconclusive. © 2010 John Wiley & Sons A/S.

Fly ash carbon passivation

Science.gov (United States)

La Count, Robert B; Baltrus, John P; Kern, Douglas G

2013-05-14

A thermal method to passivate the carbon and/or other components in fly ash significantly decreases adsorption. The passivated carbon remains in the fly ash. Heating the fly ash to about 500 and 800 degrees C. under inert gas conditions sharply decreases the amount of surfactant adsorbed by the fly ash recovered after thermal treatment despite the fact that the carbon content remains in the fly ash. Using oxygen and inert gas mixtures, the present invention shows that a thermal treatment to about 500 degrees C. also sharply decreases the surfactant adsorption of the recovered fly ash even though most of the carbon remains intact. Also, thermal treatment to about 800 degrees C. under these same oxidative conditions shows a sharp decrease in surfactant adsorption of the recovered fly ash due to the fact that the carbon has been removed. This experiment simulates the various "carbon burnout" methods and is not a claim in this method. The present invention provides a thermal method of deactivating high carbon fly ash toward adsorption of AEAs while retaining the fly ash carbon. The fly ash can be used, for example, as a partial Portland cement replacement in air-entrained concrete, in conductive and other concretes, and for other applications.

Ashes to ashes: Large Fraxinus germplasm collections and their fates

Science.gov (United States)

Kim C. Steiner; Paul. Lupo

2010-01-01

As the emerald ash borer (EAB) threatens the survival of our ash species, measures should be taken to preserve their genetic variability in the event that we discover a way to restore populations destroyed by the beetle. As it happens, large germplasm collections exist for our most important and widely distributed eastern species of the genus, white ash (...

Fusion characterization of biomass ash

Energy Technology Data Exchange (ETDEWEB)

Ma, Teng [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Sino-Danish Center for Education and Research, Beijing, 100190 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Fan, Chuigang; Hao, Lifang [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Li, Songgeng, E-mail: sgli@ipe.ac.cn [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Song, Wenli [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Lin, Weigang [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Department of Chemical and Biochemical Engineering, Technical University of Denmark, 2800 Kgs. Lyngby (Denmark)

2016-08-20

Highlights: • A novel method is proposed to analyze fusion characteristics of biomass ash. • T{sub m} can represent the severe melting temperature of biomass ash. • Compared with AFT, TMA is the better choice to analyze the fusion characteristics of biomass ash. - Abstract: The ash fusion characteristics are important parameters for thermochemical utilization of biomass. In this research, a method for measuring the fusion characteristics of biomass ash by Thermo-mechanical Analyzer, TMA, is described. The typical TMA shrinking ratio curve can be divided into two stages, which are closely related to ash melting behaviors. Several characteristics temperatures based on the TMA curves are used to assess the ash fusion characteristics. A new characteristics temperature, T{sub m}, is proposed to represent the severe melting temperature of biomass ash. The fusion characteristics of six types of biomass ash have been measured by TMA. Compared with standard ash fusibility temperatures (AFT) test, TMA is more suitable for measuring the fusion characteristics of biomass ash. The glassy molten areas of the ash samples are sticky and mainly consist of K-Ca-silicates.

Trace elements in coal ash

Science.gov (United States)

Deonarine, Amrika; Kolker, Allan; Doughten, Michael W.

2015-01-01

Coal ash is a residual waste product primarily produced by coal combustion for electric power generation. Coal ash includes fly ash, bottom ash, and flue-gas desulfurization products (at powerplants equipped with flue-gas desulfurization systems). Fly ash, the most common form of coal ash, is used in a range of products, especially construction materials. A new Environmental Protection Agency ruling upholds designation of coal ash as a non-hazardous waste under Subtitle D of the Resource Conservation and Recovery Act, allowing for the continued beneficial use of coal ash and also designating procedures and requirements for its storage.

Mercury release from fly ashes and hydrated fly ash cement pastes

Science.gov (United States)

Du, Wen; Zhang, Chao-yang; Kong, Xiang-ming; Zhuo, Yu-qun; Zhu, Zhen-wu

2018-04-01

The large-scale usage of fly ash in cement and concrete introduces mercury (Hg) into concrete structures and a risk of secondary emission of Hg from the structures during long-term service was evaluated. Three fly ashes were collected from coal-fired power plants and three blend cements were prepared by mixing Ordinary Portland cement (OPC) with the same amount of fly ash. The releasing behaviors of Hg0 from the fly ash and the powdered hydrated cement pastes (HCP) were measured by a self-developed Hg measurement system, where an air-blowing part and Hg collection part were involved. The Hg release of fly ashes at room temperature varied from 25.84 to 39.69 ng/g fly ash during 90-days period of air-blowing experiment. In contrast, the Hg release of the HCPs were in a range of 8.51-18.48 ng/g HCP. It is found that the Hg release ratios of HCPs were almost the same as those of the pure fly ashes, suggesting that the hydration products of the HCP have little immobilization effect on Hg0. Increasing temperature and moisture content markedly promote the Hg release.

Fly ash aggregates. Vliegaskunstgrind

Energy Technology Data Exchange (ETDEWEB)

1983-03-01

A study has been carried out into artificial aggregates made from fly ash, 'fly ash aggregates'. Attention has been drawn to the production of fly ash aggregates in the Netherlands as a way to obviate the need of disposal of fly ash. Typical process steps for the manufacturing of fly ash aggregates are the agglomeration and the bonding of fly ash particles. Agglomeration techniques are subdivided into agitation and compaction, bonding methods into sintering, hydrothermal and 'cold' bonding. In sintering no bonding agent is used. The fly ash particles are more or less welded together. Sintering in general is performed at a temperature higher than 900 deg C. In hydrothermal processes lime reacts with fly ash to a crystalline hydrate at temperatures between 100 and 250 deg C at saturated steam pressure. As a lime source not only lime as such, but also portland cement can be used. Cold bonding processes rely on reaction of fly ash with lime or cement at temperatures between 0 and 100 deg C. The pozzolanic properties of fly ash are used. Where cement is applied, this bonding agent itself contributes also to the strength development of the artificial aggregate. Besides the use of lime and cement, several processes are known which make use of lime containing wastes such as spray dry absorption desulfurization residues or fluid bed coal combustion residues. (In Dutch)

Hydration of fly ash cement and microstructure of fly ash cement pastes

Energy Technology Data Exchange (ETDEWEB)

Shiyuan, H.

1981-01-01

The strength development and hydration of fly ash cement and the influence of addition of gypsum on those were studied at normal and elevated temperatures. It was found that an addition of a proper amount of gypsum to fly ash cement could accelerate the pozzolanic reaction between CH and fly ash, and as a result, increase the strength of fly ash cement pastes after 28 days.

Glass-ceramic from mixtures of bottom ash and fly ash.

Science.gov (United States)

Vu, Dinh Hieu; Wang, Kuen-Sheng; Chen, Jung-Hsing; Nam, Bui Xuan; Bac, Bui Hoang

2012-12-01

Along with the gradually increasing yield of the residues, appropriate management and treatment of the residues have become an urgent environmental protection problem. This work investigated the preparation of a glass-ceramic from a mixture of bottom ash and fly ash by petrurgic method. The nucleation and crystallization kinetics of the new glass-ceramic can be obtained by melting the mixture of 80% bottom ash and 20% fly ash at 950 °C, which was then cooled in the furnace for 1h. Major minerals forming in the glass-ceramics mainly are gehlenite (Ca(2)Al(2)SiO(7)) & akermanite (Ca(2)MgSiO(7)) and wollastonite (CaSiO(3)). In addition, regarding chemical/mechanical properties, the chemical resistance showing durability, and the leaching concentration of heavy metals confirmed the possibility of engineering and construction applications of the most superior glass-ceramic product. Finally, petrurgic method of a mixture of bottom ash and fly ash at 950 °C represents a simple, inexpensive, and energy saving method compared with the conventional heat treatment. Copyright © 2012 Elsevier Ltd. All rights reserved.

On-line anti-acetylcholine esterase activity of extracts of oxystelma esculentum, aerva javanica and zanthoxylum armatum

International Nuclear Information System (INIS)

Murtaza, S.; Ullah, R. S.; Abbas, A.; Riaz, T.; Ghous, T.; Altaf, Y.; Khan, M.; Ahmed, S.

2013-01-01

Alzheimer's disease (AD), a disease of brain, resulting in memory impairment and the loss of thinking. The main reason of Alzheimer's disease is firmly associated with some impairment in cholinergic transmission. This impairment may be improved by diminishing the breakdown of acetylcholine at the synaptic site in the brain by inhibiting acetylcholinesterase (AChE). In this work, extracts of three different plants Oxystelma esculentum (OEM), Aerva javanica (AJM) and Zanthoxylum armatum (ZAA) have been screened for their anti-AchE activity. Results of the study demonstrate that of the studied extracts, ZAA (IC/sub 50/ 55.5 micro g/ml) acquired stronger anti-AChE activity. While OEM with IC/sub 50/ 107.2 micro g/ml showed moderate and ZAE and AJM showed weaker action (IC/sub 50/ 182.5 and 275.2 micro g/ml). Galanthamine was used as a positive control (IC/sub 50/ 1.47 micro g/ml). (author)

Identification of common allergens for united airway disease by skin prick test

Directory of Open Access Journals (Sweden)

Vikas Deep Mishra

2016-01-01

Full Text Available Objective: Identification of common allergens by skin prick test in patients of united airway disease. Materials and Methods: Skin prick test was performed in 60 patients of United Airway Disease to identify the common allergens. A total of 62 allergens consisting of 36 types of pollen, 5 fungi, 4 insects, 8 type of dusts, 4 dander, 3 fabrics, Dust mite and Parthenium leaves were tested. Result: Most common allergens were Dust mite (60% followed by Parthenium leaves (45%, insects (18.75%, pollen (14.81%, dust allergens (8.51%, fabrics (8.33%, fungi (5.66%, dander (5%. Most common insect allergens were cockroach (female (30%, cockroach (male (23.33%. Common pollens were Ricinus communis (28.33%, Amaranthus spinosus (28.33%, Parthenium hysterophorus (26.66%, Eucalyptus tereticornis (26.66% and Cynodon dactylon (25%. Common dust allergens were house dust (21.66%, paper dust (11.66% and cotton mill dust (10%. Among fabrics kapok cotton (13.33% showed maximum positivity. Among fungi Aspergillus fumigatus (10% followed by A. niger (6.66% were most common. In animal dander group common ones were cat dander followed by dog dander. Conclusion: In conclusion it can be said that the knowledge drawn by above study will help to treat patients by immunotherapy or avoidance strategy.

Fusion characterization of biomass ash

DEFF Research Database (Denmark)

Ma, Teng; Fan, Chuigang; Hao, Lifang

2016-01-01

The ash fusion characteristics are important parameters for thermochemical utilization of biomass. In this research, a method for measuring the fusion characteristics of biomass ash by Thermo-mechanical Analyzer, TMA, is described. The typical TMA shrinking ratio curve can be divided into two...... stages, which are closely related to ash melting behaviors. Several characteristics temperatures based on the TMA curves are used to assess the ash fusion characteristics. A new characteristics temperature, Tm, is proposed to represent the severe melting temperature of biomass ash. The fusion...... characteristics of six types of biomass ash have been measured by TMA. Compared with standard ash fusibility temperatures (AFT) test, TMA is more suitable for measuring the fusion characteristics of biomass ash. The glassy molten areas of the ash samples are sticky and mainly consist of K-Ca-silicates....

Arsenic, chromium and mercury removal using mussel shell ash or a sludge/ashes waste mixture.

Science.gov (United States)

Seco-Reigosa, Natalia; Peña-Rodríguez, Susana; Nóvoa-Muñoz, Juan Carlos; Arias-Estévez, Manuel; Fernández-Sanjurjo, María J; Alvarez-Rodríguez, Esperanza; Núñez-Delgado, Avelino

2013-04-01

Different batches of valued mussel shell and waste mussel shell ash are characterised. Shell ash has pH > 12 and high electrical conductivities (between 16.01 and 27.27 dS m(-1)), while calcined shell shows pH values up to 10.7 and electrical conductivities between 1.19 and 3.55 dS m(-1). X-ray fluorescence, nitric acid digestion and water extractions show higher concentrations in shell ash for most parameters. Calcite is the dominant crystalline compound in this ash (95.6%), followed by aragonite. Adsorption/desorption trials were performed for mussel shell ash and for a waste mixture including shell ash, sewage sludge and wood ash, showing the following percentage adsorptions: Hg(II) >94%, As(V) >96% and Cr(VI) between 11 and 30% for shell ash; Hg(II) >98%, As(V) >88% and Cr(VI) between 30 and 88% for the waste mixture. Hg and As desorption was ash and the waste mixture, while Cr desorption was between 92 and 45% for shell ash, and between 19 and 0% for the mixture. In view of that, mussel shell ash and the mixture including shell ash, sewage sludge and wood ash could be useful for Hg(II) and As(V) removal.

Prick test: evolution towards automated reading.

Science.gov (United States)

Justo, X; Díaz, I; Gil, J J; Gastaminza, G

2016-08-01

The prick test is one of the most common medical methods for diagnosing allergies, and it has been carried out in a similar and laborious manner over many decades. In an attempt to standardize the reading of the test, many researchers have tried to automate the process of measuring the allergic reactions found by developing systems and algorithms based on multiple technologies. This work reviews the techniques for automatic wheal measurement with the aim of pointing out their advantages and disadvantages and the progress in the field. Furthermore, it provides a classification scheme for the different technologies applied. The works discussed herein provide evidence that significant challenges still exist for the development of an automatic wheal measurement system that not only helps allergists in their medical practice but also allows for the standardization of the reading and data exchange. As such, the aim of the work was to serve as guideline for the development of a proper and feasible system. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Exploring the molecular and biochemical basis of ash resistance to emerald ash borer

Science.gov (United States)

Justin G.A. Whitehill; Daniel A. Herms; Pierluigi. Bonello

2010-01-01

Larvae of the emerald ash borer (EAB) (Agrilus planipennis) feed on phloem of ash (Fraxinus spp.) trees. It is hypothesized that the resistance of Asian species of ash (e.g., Manchurian ash, F. mandshurica) to EAB is due to endogenous defenses present in phloem tissues in the form of defensive proteins and/or...

Properties and Leachability of Self-Compacting Concrete Incorporated with Fly Ash and Bottom Ash

Science.gov (United States)

Kadir, Aeslina Abdul; Ikhmal Haqeem Hassan, Mohd; Jamaluddin, Norwati; Bakri Abdullah, Mohd Mustafa Al

2016-06-01

The process of combustion in coal-fired power plant generates ashes, namely fly ash and bottom ash. Besides, coal ash produced from coal combustion contains heavy metals within their compositions. These metals are toxic to the environment as well as to human health. Fortunately, treatment methods are available for these ashes, and the use of fly ash and bottom ash in the concrete mix is one of the few. Therefore, an experimental program was carried out to study the properties and determine the leachability of selfcompacting concrete incorporated with fly ash and bottom ash. For experimental study, self-compacting concrete was produced with fly ash as a replacement for Ordinary Portland Cement and bottom ash as a replacement for sand with the ratios of 10%, 20%, and 30% respectively. The fresh properties tests conducted were slump flow, t500, sieve segregation and J-ring. Meanwhile for the hardened properties, density, compressive strength and water absorption test were performed. The samples were then crushed to be extracted using Toxicity Characteristic Leaching Procedure and heavy metals content within the samples were identified accordingly using Atomic Absorption Spectrometry. The results demonstrated that both fresh and hardened properties were qualified to categorize as self-compacting concrete. Improvements in compressive strength were observed, and densities for all the samples were identified as a normal weight concrete with ranges between 2000 kg/m3 to 2600 kg/m3. Other than that, it was found that incorporation up to 30% of the ashes was safe as the leached heavy metals concentration did not exceed the regulatory levels, except for arsenic. In conclusion, this study will serve as a reference which suggests that fly ash and bottom ash are widely applicable in concrete technology, and its incorporation in self-compacting concrete constitutes a potential means of adding value to appropriate mix and design.

Effect of ash components on the ignition and burnout of high ash coals

Energy Technology Data Exchange (ETDEWEB)

Feng, B.; Yan, R.; Zheng, C.G. [Huazhong University of Science and Technology, Wuhan (China). National Laboratory of Coal Combustion

1998-11-01

The effect of the ash components on the ignition and burnout of four Chinese high ash coals were studied by thermogravimetric analysis. To investigate the influence of the ash components, comparative experiments were carried out with original, deashed and impregnated coals. Eleven types of ash components, such as SiO{sub 2}, CaCO{sub 3}, MgO, Na{sub 2}CO{sub 3}, K{sub 2}CO{sub 3}, Al{sub 2}O{sub 3}, TiO{sub 2}, Fe{sub 2}O{sub 3}, FeS{sub 2}, NH{sub 4}Fe(SO{sub 4}){sub 2}{center_dot}12H{sub 2}O and FeSO{sub 4},(NH{sub 4}){center_dot}6H{sub 2}O were used in the present study. It was found that most of the ash components have negative effects. The strong influence of some ash components suggests that the combustion characteristics of high ash coal may be determined by the ash composition. 5 refs., 2 figs., 2 tabs.

Shedding of ash deposits

DEFF Research Database (Denmark)

Zbogar, Ana; Frandsen, Flemming; Jensen, Peter Arendt

2009-01-01

Ash deposits formed during fuel thermal conversion and located on furnace walls and on convective pass tubes, may seriously inhibit the transfer of heat to the working fluid and hence reduce the overall process efficiency. Combustion of biomass causes formation of large quantities of troublesome...... ash deposits which contain significant concentrations of alkali, and earth-alkali metals. The specific composition of biomass deposits give different characteristics as compared to coal ash deposits, i.e. different physical significance of the deposition mechanisms, lower melting temperatures, etc....... Low melting temperatures make straw ashes especially troublesome, since their stickiness is higher at lower temperatures, compared to coal ashes. Increased stickiness will eventually lead to a higher collection efficiency of incoming ash particles, meaning that the deposit may grow even faster...

Pengaruh Kombinasi Fly Ash dan Bottom Ash sebagai Bahan Substitusi pada Campuran Beton terhadap Sifat Mekanis

OpenAIRE

Yahya, Tengku Tantoni; Kurniawandy, Alex; Djauhari, Zulfikar

2017-01-01

Fly ash and bottom ash were waste that generated from the power plant burning coal process. Fly ash and bottom ash has the potential to be developed as a basic ingredient in concrete composites. This research aimed to obtain the properties of fresh concrete and hard concrete of the combined effect of fly ash and bottom ash as a substitute ingredient in composite concrete. This research has examined the influence of a combination of waste fly ash and bottom ash to the compressive strength of a...

Melting and Sintering of Ashes

DEFF Research Database (Denmark)

Hansen, Lone Aslaug

1997-01-01

-1300°C, and a trend of higher fusion temperatures with increasing contents of Al-silicates and quartz was found.c) Fly ashes, bottom ashes and deposits from coal/straw co-firing were all found to consist mainly of metal-alumina and alumina-silicates. These ashes all melt in the temperature range 1000......The thesis contains an experimental study of the fusion and sintering of ashes collected during straw and coal/straw co-firing.A laboratory technique for quantitative determination of ash fusion has been developed based on Simultaneous Thermal Analysis (STA). By means of this method the fraction......, the biggest deviations being found for salt rich (i.e. straw derived) ashes.A simple model assuming proportionality between fly ash fusion and deposit formation was found to be capable of ranking deposition rates for the different straw derived fly ashes, whereas for the fly ashes from coal/straw co-firing...

Investigation on Leaching Behaviour of Fly Ash and Bottom Ash Replacement in Self-Compacting Concrete

Science.gov (United States)

Kadir, Aeslina Abdul; Ikhmal Haqeem Hassan, Mohd; Bakri Abdullah, Mohd Mustafa Al

2016-06-01

Fly ash and bottom ash are some of the waste generated by coal-fired power plants, which contains large quantities of toxic and heavy metals. In recent years, many researchers have been interested in studying on the properties of self-compacting concrete incorporated with fly ash and bottom ash but there was very limited research from the combination of fly ash and bottom ash towards the environmental needs. Therefore, this research was focused on investigating the leachability of heavy metals of SCC incorporated with fly ash and bottom ash by using Toxicity Characteristic Leaching Procedure, Synthetic Precipitation Leaching Procedure and Static Leaching Test. The samples obtained from the coal-fired power plant located at Peninsula, Malaysia. In this study, the potential heavy metals leached out from SCC that is produced with fly ash as a replacement for Ordinary Portland Cement and bottom ash as a substitute for sand with the ratios from 10% to 30% respectively were designated and cast. There are eight heavy metals of concern such as As, Cr, Pb, Zn, Cu, Ni, Mn and Fe. The results indicated that most of the heavy metals leached below the permissible limits from the United States Environmental Protection Agency and World Health Organization limit for drinking water. As a conclusion, the minimum leaching of the heavy metals from the incorporation of fly ash and bottom ash in self-compacting concrete was found in 20% of fly ash and 20% of bottom ash replacement. The results also indicate that this incorporation could minimize the potential of environmental problems.

Processed bottom ash for replacing fine aggregate in making high-volume fly ash concrete

Directory of Open Access Journals (Sweden)

Antoni

2017-01-01

Full Text Available Bottom ash is a coal plant by-product that is abundant and underutilized. There is the potential use of bottom ash as a fine aggregate replacement in concrete mixtures; however, the problems of water absorption and uniformity of quality of the material need to be overcome first. In this study, bottom ash was treated by sieve separation and pounding to smaller particle size for use as a sand substitute. The physical and chemical characteristics of bottom ash were tested after treatment including water absorption, sieve analysis, and fineness modulus. Highvolume fly ash (HVFA mortar specimens were made and the compressive strength and flowability test using bottom ash after treatment are compared with that of the sand specimen. Low water to cementitious ratio was used to ensure higher strength from the cementitious paste and superplasticizer demand was determined for each treatment. The result showed that bottom ash can be used as fine aggregate replacement material. Sieve separation of the bottom ash could produce 75% of the compressive strength compared with the control sand specimen, whereas pounded bottom ash could have up to 96% of the compressive strength of the control specimen. A 28-day compressive strength of 45 MPa was achievable with 100% replacement of fine aggregate with bottom ash.

Analgesia Synergism of Essential Oil from Pericarp of Zanthoxylum schinifolium and Verapamil

Directory of Open Access Journals (Sweden)

Gao Wu

2014-01-01

Full Text Available Objective. To evaluate the synergistic analgesic effect of essential oil of Zanthoxylum schinifolium Sieb. et Zucc. (EOZ and verapamil (Ver. Method. The qualitative and quantitative composition of EOZ were determined with gas chromatography/Mass spectrometer. The interaction between EOZ and Ver in antinociceptive activity was evaluated by using acetic acid-induced writhing, hot plate, and tail flick tests in mice and in isolated toad sciatic nerve test. Results. Linalool, limonene, and sabinene are the major components of EOZ. EOZ (middle-dose: 40 mg·kg−1, high-dose: 80 mg·kg−1 and EOZ + Ver (Each dose group have remarkable analgesic effects on pain in mice induced by acetic acid-induced writhing, hot plate, and tail flick tests. Low-dose EOZ (20 mg·kg−1 had no analgesic action, but when it is combined with Ver it has shown significant antinociception. Verapamil has a faint analgesic effect but was not able to inhibit action potential transmission in toad sciatic nerve. EOZ (0.2% and EOZ + Ver (0.2% + 0.05% also inhibited action potential transmission in toad sciatic nerve. Combination of EOZ with Ver had a greater analgesic effect and inhibition of nerve action potential transmission compared to its components EOZ and Ver. Conclusion. The combination of EOZ with Ver produces a synergistic analgesic effect.

Ash fusion temperatures and the transformations of coal ash particles to slag

Energy Technology Data Exchange (ETDEWEB)

Gupta, S.K.; Wall, T.F.; Creelman, R.A.; Gupta, R.P. [University of Newcastle, Newcastle, NSW (Australia). CRC for Black Coal Utilisation

1998-07-01

A mechanistic study is detailed in which coal ash is heated with its shrinkage measured continuously up to a temperature of 1600{degree}C. The temperature corresponding to the rapid rate of shrinkage correspond to the formation of eutectics identified on phase diagrams. Samples were therefore heated to these temperatures, cooled rapidly and examined using a scanning electron microscope (SEM) to identify the associated chemical and physical changes. The progressive changes in the range of chemical composition (from SEM), the extent of undissolved ash particles and porosity were then quantified and related to homogenisation, viscosity and ash fusion mechanisms. Alternate ash fusion temperatures based on different levels of shrinkage have also been suggested to characterise the ash deposition tendency of the coals. 13 refs., 9 figs.

Interspecific proteomic comparisons reveal ash phloem genes potentially involved in constitutive resistance to the emerald ash borer.

Science.gov (United States)

Whitehill, Justin G A; Popova-Butler, Alexandra; Green-Church, Kari B; Koch, Jennifer L; Herms, Daniel A; Bonello, Pierluigi

2011-01-01

The emerald ash borer (Agrilus planipennis) is an invasive wood-boring beetle that has killed millions of ash trees since its accidental introduction to North America. All North American ash species (Fraxinus spp.) that emerald ash borer has encountered so far are susceptible, while an Asian species, Manchurian ash (F. mandshurica), which shares an evolutionary history with emerald ash borer, is resistant. Phylogenetic evidence places North American black ash (F. nigra) and Manchurian ash in the same clade and section, yet black ash is highly susceptible to the emerald ash borer. This contrast provides an opportunity to compare the genetic traits of the two species and identify those with a potential role in defense/resistance. We used Difference Gel Electrophoresis (DIGE) to compare the phloem proteomes of resistant Manchurian to susceptible black, green, and white ash. Differentially expressed proteins associated with the resistant Manchurian ash when compared to the susceptible ash species were identified using nano-LC-MS/MS and putative identities assigned. Proteomic differences were strongly associated with the phylogenetic relationships among the four species. Proteins identified in Manchurian ash potentially associated with its resistance to emerald ash borer include a PR-10 protein, an aspartic protease, a phenylcoumaran benzylic ether reductase (PCBER), and a thylakoid-bound ascorbate peroxidase. Discovery of resistance-related proteins in Asian species will inform approaches in which resistance genes can be introgressed into North American ash species. The generation of resistant North American ash genotypes can be used in forest ecosystem restoration and urban plantings following the wake of the emerald ash borer invasion.

Characteristics of prickly lettuce seed oil in relation to methods of extraction.

Science.gov (United States)

Ramadan, A A

1976-01-01

Samples of seed oil of prickly lettuce (Lactuca Sacriola oleifera) which had been obtained by pressing or by extracting with acetone, ethyl ether, petroleum ether or carbon tetrachloride were analysed for the following parameters: viscosity, saponification number, iodine number, thiocyanogen value, unsaponifiable matter, free fatty acids, peroxide number and fatty acid composition. The different parameters varied in part considerably in relation to the method of production (pressing or solvent extraction) and to the solvent. It is tried to interprete these relationships.

Survey for tolerance to emerald ash borer within North American ash species

Science.gov (United States)

Jennifer L. Koch; Mary E. Mason; David W. Carey; Kathleen Knight; Therese Poland; Daniel A. Herms

2010-01-01

Since the discovery of the emerald ash borer (EAB) near Detroit, MI, in 2002, more than 40 million ash trees have been killed and another 7.5 billion are at risk in the United States. When the EAB outbreak was initially discovered, our native ash species appeared to have no resistance to the pest.

Larvicidal activity and structure activity relationship of cinnamoyl amides from Zanthoxylum armatum and their synthetic analogues against diamondback moth, Plutella xylostella.

Science.gov (United States)

Kumar, Vishal; Reddy, S G Eswara; Bhardwaj, Anuja; Dolma, Shudh Kirti; Kumar, Neeraj

2016-01-01

Cinnamoyl amides isolated from Zanthoxylum armatum (Rutaceae) and their synthetic analogues were tested for their insecticidal activity against the second instar larvae of diamondback moth, Plutella xylostella (L.) (Lepidoptera: Yponomeutidae) to determine the promising structures with insecticidal activity. Most of the test compounds showed promising activity against larvae of P. xylostella. However, the activities of different compounds varied depending on the presence of different substituents at various positions of both the aromatic rings A and B. Among the tested compounds, 8, N-(3-bromo-4-methoxyphenethyl)cinnamamide showed best larvicidal activity with an LC50 = 62.13 mg/L followed by 6, N-(3׳-bromophenethyl)cinnamamide (LC50=128.49 mg/L) and 2 N-(4׳-methoxyphenylethyl)cinnamamide (LC50 = 225.65 mg/L).

Cast-concrete products made with FBC ash and wet-collected coal-ash

Energy Technology Data Exchange (ETDEWEB)

Naik, T.R.; Kraus, R.N.; Chun, Y.M.; Botha, F.D. [University of Wisconsin, Milwaukee, WI (United States)

2005-12-01

Cast-concrete hollow blocks, solid blocks, and paving stones were produced at a manufacturing plant by replacing up to 45% (by mass) of portland cement with fluidized bed combustion (FBC) coal ash and up to 9% of natural aggregates with wet-collected, low-lime, coarse coal-ash (WA). Cast-concrete product specimens of all three types exceeded the compressive strength requirements of ASTM from early ages, with the exception of one paving-stone mixture, which fell short of the requirement by less than 10%. The cast-concrete products made by replacing up to 40% of cement with FBC ash were equivalent in strength (89-113% of control) to the products without ash. The abrasion resistance of paving stones was equivalent for up to 34% FBC ash content. Partial replacement of aggregates with WA decreased strength of the products. The resistance of hollow blocks and paving stones to freezing and thawing decreased appreciably with increasing ash contents. The cast-concrete products could be used indoors in regions where freezing and thawing is a concern, and outdoors in a moderate climate.

Can ash clog soil pores?

Science.gov (United States)

Stoof, Cathelijne; Stoof, Cathelijne; Gevaert, Anouk; Gevaert, Anouk; Baver, Christine; Baver, Christine; Hassanpour, Bahareh; Hassanpour, Bahareh; Morales, Veronica; Morales, Veronica; Zhang, Wei; Zhang, Wei; Martin, Deborah; Martin, Deborah; Steenhuis, Tammo; Steenhuis, Tammo

2015-04-01

Wildfire can greatly increase a landscape's vulnerability to flooding and erosion events, and ash is thought to play a large role in controlling runoff and erosion processes after wildfire. Although ash can store rainfall and thereby reduce runoff and erosion for a limited period after wildfires, it has also been hypothesized to clog soil pores and reduce infiltration. Several researchers have attributed the commonly observed increase in runoff and erosion after fire to the potential pore-clogging effect of ash. Evidence is however incomplete, as to date, research has solely focused on identifying the presence of ash in the soil, with the actual flow processes associated with the infiltration and pore-clogging of ash remaining a major unknown. In several laboratory experiments, we tested the hypothesis that ash causes pore clogging to the point that infiltration is hampered and ponding occurs. We first visualized and quantified pore-scale infiltration of water and ash in sand of a range of textures and at various infiltration rates, using a digital bright field microscope capturing both photo and video. While these visualization experiments confirm field and lab observation of ash washing into soil pores, we did not observe any clogging of pores, and have not been able to create conditions for which this does occur. Additional electrochemical analysis and measurement of saturated hydraulic conductivity indicate that pore clogging by ash is not plausible. Electrochemical analysis showed that ash and sand are both negatively charged, showing that attachment of ash to sand and any resulting clogging is unlikely. Ash also had quite high saturated conductivity, and systems where ash was mixed in or lying on top of sand had similarly high hydraulic conductivity. Based on these various experiments, we cannot confirm the hypothesis that pore clogging by ash contributes to the frequently observed increase in post-fire runoff, at least for the medium to coarse sands

Patch and Prick Tests in Hand Eczema: Results of A Sixty Seven Patient Series

Directory of Open Access Journals (Sweden)

Bilge Fettahlıoğlu Karaman

2017-12-01

Full Text Available Objective: The patch and prick tests have a place in the management of patients with hand eczema. In this study, we investigated whether some of the clinical features patients with hand eczema could provide us with the predictability of skin test results. Methods: In Çukurova University Faculty of Medicine, 67 consecutive patients with hand eczema; evaluated in terms of duration of disease, morphology and severity. All of the patients were undergoes patch tested with the European Standard Series, and needle testing with routine aeroallergens. Results: Patch test with at least one allergen was positive in 46.3% of the patients; wheras this rate was 23.9% for prick test. The likelihood of having a contact sensitivity of patients complaining of hand eczema for at least three years was statistically more significant [odds ratio (OR 0.9]. Although statistically not significant, it is less likely to be sensitized to patients with keratotic and/or licheniform hand eczema (OR 0.3. The severity of hand eczema was not predictive of patch test, there was no indicator of needle test positivity. Conclusion: We strongly recommend patch testing in all patients with prolonged hand eczema.

Ash study for biogas purification

International Nuclear Information System (INIS)

Juarez V, R. I.

2016-01-01

This work evaluates the ashes generated from the wood and coal combustion process of the thermoelectric plant in Petacalco, Guerrero (Mexico) in order to determine its viability as a filter in the biogas purification process. The ash is constituted by particles of morphology and different chemical properties, so it required a characterization of the same by different analytical techniques: as was scanning electron microscopy and X-ray diffraction, in order to observe the microstructure and determine the elemental chemical composition of the particles. Prior to the analysis, a set of sieves was selected to classify as a function of particle size. Four different types of ashes were evaluated: one generated by the wood combustion (wood ash) and three more of the Petacalco thermoelectric generated by the coal combustion (wet fly ash, dry fly ash and dry bottom ash). (Author)

Lunar ash flows - Isothermal approximation.

Science.gov (United States)

Pai, S. I.; Hsieh, T.; O'Keefe, J. A.

1972-01-01

Suggestion of the ash flow mechanism as one of the major processes required to account for some features of lunar soil. First the observational background and the gardening hypothesis are reviewed, and the shortcomings of the gardening hypothesis are shown. Then a general description of the lunar ash flow is given, and a simple mathematical model of the isothermal lunar ash flow is worked out with numerical examples to show the differences between the lunar and the terrestrial ash flow. The important parameters of the ash flow process are isolated and analyzed. It appears that the lunar surface layer in the maria is not a residual mantle rock (regolith) but a series of ash flows due, at least in part, to great meteorite impacts. The possibility of a volcanic contribution is not excluded. Some further analytic research on lunar ash flows is recommended.

Regular Recycling of Wood Ash to Prevent Waste Production (RecAsh). Technical Final Report

Energy Technology Data Exchange (ETDEWEB)

Andersson, Lars E-mail: lars.t.andersson@skogsstyreslen.se

2007-03-15

At present, the extraction of harvest residues is predicted to increase in Sweden and Finland. As an effect of the intensified harvesting, the export of nutrients and acid buffering substances from the growth site is also increased. Wood ash could be used to compensate forest soils for such losses. Most wood fuel ash is today often deposited in landfills. If the wood ash is recycled, wood energy is produced without any significant waste production. Ash recycling would therefore contribute to decreasing the production of waste, and to maintaining the chemical quality of forest waters and biological productivity of forest soils in the long term. The project has developed, analysed and demonstrated two regular ash-recycling systems. It has also distributed knowledge gathered about motives for ash recycling as well as technical and administrative solutions through a range of media (handbooks, workshops, field demonstrations, reports, web page and information videos). Hopefully, the project will contribute to decreasing waste problems related to bio-energy production in the EU at large. The project has been organised as a separate structure at the beneficiary and divided in four geographically defined subprojects, one in Finland and three in Sweden (Central Sweden, Northern Sweden, and South-western Sweden). The work in each subproject has been lead by a subproject leader. Each subproject has organised a regional reference group. A project steering committee has been established consisting of senior officials from all concerned partners. The project had nine main tasks with the following main expected deliverables and output: 1. Development of two complete full-scale ash-recycling systems; 2. Production of handbooks of the ash recycling system; 3. Ash classification study to support national actions for recommendations; 4. Organise regional demonstrations of various technical options for ash treatment and spreading; 5. Organise national seminars and demonstrations of

Electrodialytic removal of heavy metals from different fly ashes. Influence of heavy metal speciation in the ashes

DEFF Research Database (Denmark)

Pedersen, Anne Juul; Ottosen, Lisbeth M.; Villumsen, Arne

2003-01-01

Electrodialytic Remediation has recently been suggested as a potential method for removal of heavy metals from fly ashes. In this work electrodialytic remediation of three different fly ashes, i.e. two municipal solid waste incinerator (MSWI) fly ashes and one wood combustion fly ash was studied...... in lab scale, and the results were discussed in relation to the expected heavy metal speciation in the ashes. In initial leaching experiments the pH-dependent desorption characteristics of the heavy metals Cd, Pb, Zn and Cu were analogous in the two MSWI ashes, and thus it was expected......-moval efficiencies were observed, especially for Pb and Zn. Cd, the sole heavy metal of environmental concern in the wood ash, was found more tightly bonded in this ash than in the two MSWI ashes. It was suggested that complex Cd-silicates are likely phases in the wood ash whereas more soluble, condensed phases...

First international ash marketing and technology conference

Energy Technology Data Exchange (ETDEWEB)

1978-01-01

A total of 42 papers were presented in sessions with the following headings: production and disposal of ash - an international review; environmental, health, safety, and legal aspects of ash handling; marketing of ash; development of new uses for ash; cementitious use of ash; ash in manufactured products; and geotechnical uses of ash.

Determining ash content in flotation wastes by means of the MPOF optical ash meter. [Poland

Energy Technology Data Exchange (ETDEWEB)

Sikora, T; Sliwa, J

1982-03-01

The paper evaluates an experimental unit of the MPOF optical ash meter, developed by the EMAG Research and Production Center for Electrical Engineering and Mining Automation. The MPOF, which is being tested at the coal preparation plant of the 30 lecia PRL mine, is the first system for continuous determination of ash content in flotation tailings developed in Poland. A block scheme of the system is given. It consists of a measuring head and electronic system which processes data supplied by the measuring head and calculates ash content. System operation is based on the principle of determining ash content in a mixture of coal and mineral wastes by measuring mixture reflectivity. Determining ash content in the mixture is possible as reflectivity coefficients for coal and ash are constant. Performance of the MPOF optical ash meter is evaluated; the results are shown in a table and a scheme. Measurement accuracy is satisfactory.

Low antiplasmodial activity of alkaloids and amides from the stem bark of Zanthoxylum rubescens (Rutaceae

Directory of Open Access Journals (Sweden)

Penali L.

2007-06-01

Full Text Available The stem bark of Zanthoxylum rubescens (syn. Fagara rubescens is used for treating fevers associated with malaria in the Ivory Coast. Three alkaloids: N-nornitidine, 7,9-dimethoxy-2,3- methylenedioxybenzophenanthridine, and bis[6-(5,6- dihydrochelerythrinyl] ether; and two amides: zanthomamide and lemairamide, were isolated from the stem bark of this plant. These compounds were screened in vitro against the chloroquine-sensitive 3D7 strain and the chloroquine-resistant FCM29 strain of P. falciparum. N-nornitidine was found to be inactive. 7,9- dimethoxy-2,3-methylenedioxybenzophenanthridine, lemairamide and zanthomamide showed weak activity with average IC50 values ranging from 45.6 μM to 149.9 μM. Bis[6-(5,6- dihydrochelerythrinyl] ether was the most active of the tested compounds with mean IC50s of 14.9 ± 1.4 μM in FCM29 strain and 15.3 ± 3.4 μM in 3D7 strain (~ 58 to ~ 1130 times less active than chloroquine respectively. The anti-Plasmodium activities of the tested alkaloids of Z. rubescens were low; and do not encourage the use of this plant as antimalarial.

Fire effects on the population structure of Zanthoxylum rhoifolium Lam (Rutaceae in a Brazilian savanna

Directory of Open Access Journals (Sweden)

IA. Silva

Full Text Available Since cerrado fires may impede the growth of seedlings into trees, they may shape the population of woody species. In this study, we assessed the effects of a severe fire on the population structure and spatial distribution of Zanthoxylum rhoifolium, a widespread cerrado tree. We were interested to know the importance of the resprouting and sexual reproduction in regenerating the population. The study area had been for about six years protected from fire, before a severe fire at the end of the dry season in 2006. We sampled and measured all individuals of Z. rhoifolium found in 80 plots of 25 m². We found 149 individuals before the fire and 112 after the fire, of which 77 were resprouts from burned seedlings and saplings. We did not find significant differences between the population structure before and after the fire. The spatial distribution of the population remained clumped after the fire. Thus, the Z. rhoifolium population was very resilient to a severe fire. We did not find any new seedlings. As a consequence, resprouting seems to be more important than sexual reproduction in promptly regenerating the Z. rhoifolium populations.

Biodiversity, Phylogeny, and Antifungal Functions of Endophytic Fungi Associated with Zanthoxylum bungeanum

Directory of Open Access Journals (Sweden)

Peiqin Li

2016-09-01

Full Text Available This study investigated the biodiversity, phylogeny, and antifungal activity of endophytic fungi isolated from Zanthoxylum bungeanum. A total of 940 isolates obtained were grouped into 93 morphotypes, 43 species, and 23 genera, which were authenticated by molecular identification based on rDNA internal transcribed spacer (ITS sequence analysis. A high diversity of endophytic fungi from Z. bungeanum are observed with high species richness S (43, Margalef index D′ (6.1351, Shannon–Wiener index H′ (3.2743, Simpson diversity index Ds (0.9476, PIE index (0.9486, and evenness Pielou index J (0.8705 but a low dominant index λ (0.0524. Significant tissue specificity of the endophytic fungi was observed in Z. bungeanum, and the highest species richness and diversity indexes were obtained in the stem. Phylogenetic analyses of the 93 endophytic isolates were carried out by the neighbor-joining (NJ method to demonstrate their evolutionary processes. Antifungal activities of endophytic fungi were assayed and eight endophytic isolates showed strong and long-lasting inhibition against host pathogenic fungi Fusarium sambucinum and Pseudocercospora zanthoxyli. Here, for the first time, we systematically demonstrate the biodiversity, phylogeny, and antifungal activity of endophytic fungi associated with Z. bungeanum and reveal the value of sampling different tissues of a given plant to obtain the greatest endophyte species diversity, which might offer a framework for further investigation and utilization of endophytic fungi as aunique source of interesting and useful bioactive compounds.

[Determination of amitrole in agricultural products by high performance liquid chromatography-tandem mass spectrometry].

Science.gov (United States)

Li, Li; Fu, Jian; Gao, Hongliang; Ren, Haitao; Lou, Xishan; Guan, Lihui

2010-03-01

A high performance liquid chromatography-tandem mass spectrometry method (HPLC-MS/MS) was developed for the analysis of amitrole residues in agricultural products. The samples were extracted by 25% acetone for wheat, fish, pork and liver samples, 1% acetic acid-25% acetone for maize and peanut samples, 1% acetic acid solution for honeysuckle, the powder of ginger, the powder of bunge prickly ash and tea leaves samples, 1% acetic acid solution-dichloromethane for apple, pineapple, spinach, carrot, perilla leaves samples, respectively, followed by liquid-liquid extraction with dichloromethane. The samples were then cleaned up by PCX or Envi-Carb solid-phase extraction cartridge. The amitrole was determined and confirmed by HPLC-MS/MS. The results showed a linear relationship in the range of 0.005 -0.1 mg/kg for amitrole. The correlation coefficient was 0.999 7. The average recoveries of amitrole in wheat, maize, peanut, pineapple, apple, carrot, spinach, pork, the powder of ginger, the powder of bunge prickly ash, perilla, liver, fish, honeysuckle and tea were 67.5% - 98.1%. The relative standard deviations (RSDs) were 1.0% - 9.8%. The limits of quantitation were 10 microg/kg for wheat, maize, peanut, pineapple, apple, carrot, spinach, pork, perilla, liver, fish, honeysuckle and 20 microg/kg for the powder of bunge prickly ash, the powder of ginger and tea, respectively. The method is simple, sensitive and accurate.

Ash Properties of Alternative Biomass

DEFF Research Database (Denmark)

Capablo, Joaquin; Jensen, Peter Arendt; Pedersen, Kim Hougaard

2009-01-01

analysis into three main groups depending upon their ash content of silica, alkali metal, and calcium and magnesium. To further detail the biomass classification, the relative molar ratio of Cl, S, and P to alkali were included. The study has led to knowledge on biomass fuel ash composition influence...... on ash transformation, ash deposit flux, and deposit chlorine content when biomass fuels are applied for suspension combustion....

Behavioral properties of essential oils of zanthoxylum armatum dc leaves: augmented by chemical profile using gc/gc-ms

International Nuclear Information System (INIS)

Muhammad, N.; Khan, A.Z.; Barkatullah, A.; Ibrar, M.

2013-01-01

In the present study, the essential oils of the leaves of Zanthoxylum armatum (ZEO) were screened for various behavioral properties viz., sedative-hypnotic, anxiolytic, antidepressant, and muscle relaxant activities. In sedative-hypnotic assays, ZEO demonstrated marked reduction in mice movement in open field test at 100 and 200 mg/kg i.p. and potentiated the duration of sleep, in phenobarbitone induced sleeping mice. Profound reduction in the number of steps and rearing were observed at 100 and 200 mg/kg in a dose dependent manner. When analyzed in forced swimming test, it was devoid of any antidepressant effect at test doses. Similarly, ZEO showed significant muscle relaxant activity at 100 and 200 mg/kg i.p. in both chimney test and inclined plant test. GC/GC-MS analysis of ZEO led to the identification of 34 components, linalool being the most dominant constituent. The results suggested that ZEO has strong sedative-hypnotic, anxiolytic and muscle relaxant properties in various animal models. (author)

Synergistic mosquito-repellent activity of Curcuma longa, Pogostemon heyneanus and Zanthoxylum limonella essential oils.

Science.gov (United States)

Das, N G; Dhiman, Sunil; Talukdar, P K; Rabha, Bipul; Goswami, Diganta; Veer, Vijay

2015-01-01

Mosquito repellents play an important role in preventing man-mosquito contact. In the present study, we evaluated the synergistic mosquito-repellent activity of Curcuma longa, Pogostemon heyneanus and Zanthoxylum limonella essential oils. The mosquito repellent efficacies of three essential oils were evaluated separately and in combination under laboratory and field conditions. N,N-Diethylphenylacetamide (DEPA) and dimethylphthalate (DMP) were used for comparison of the protection time of the mixture of essential oils. At an optimum concentration of 20%, the essential oils of C. longa, Z. limonella and P. heyneanus provided complete protection times (CPTs) of 96.2, 91.4 and 123.4 min, respectively, against Aedes albopictus mosquitoes in the laboratory. The 1:1:2 mixture of the essential oils provided 329.4 and 391.0 min of CPT in the laboratory and field trials, respectively. The percent increases in CPTs for the essential oil mixture were 30 for DMP and 55 for N,N-diethylphenylacetamide (DEPA). The synergistic repellent activity of the essential oils used in the present study might be useful for developing safer alternatives to synthetic repellents for personal protection against mosquitoes. Copyright © 2015 King Saud Bin Abdulaziz University for Health Sciences. Published by Elsevier Ltd. All rights reserved.

Rapid Determination of the Geographical Origin of Chinese Red Peppers (Zanthoxylum Bungeanum Maxim.) Based on Sensory Characteristics and Chemometric Techniques.

Science.gov (United States)

Yin, Xiangqian; Xu, Xiaoxue; Zhang, Qiang; Xu, Jianguo

2018-04-24

In this paper, principal component analysis (PCA), linear discriminant analysis (LDAp, artificial neural networks (ANN), and support vector machine (SVM) were applied to discriminate the geographical origin of Chinese red peppers ( Zanthoxylum bungeanum Maxim.). The models based on color, smell and taste may discriminate quickly and effectively the geographical origin of Chinese red peppers from different regions, but the successful identification rates may vary with different kinds of parameters and chemometric methods. Among them, all models based on taste indexes showed an excellent ability to discriminate the geographical origin of Chinese red peppers with correct classifications of 100% for the training set and the 100% for test set. The present study provided a simple, efficient, inexpensive, practical and fast method to discriminate the geographical origin of Chinese red peppers from different regions, which was of great importance for both consumers and producers.

Biotic and abiotic factors affect green ash volatile production and emerald ash borer adult feeding preference.

Science.gov (United States)

Chen, Yigen; Poland, Therese M

2009-12-01

The emerald ash borer, Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), is an exotic woodborer first detected in 2002 in Michigan and Ontario and is threatening the ash resource in North America. We examined the effects of light exposure and girdling on green ash (Fraxinus pennsylvanica Marsh) volatile production, and effects of light exposure, girdling, and leaf age on emerald ash borer adult feeding preferences and phototaxis. Green ash seedlings grown under higher light exposure had lower amounts of three individual volatile compounds, (Z)-3-hexenol, (E)-beta-ocimene, and (Z,E)-alpha-farnesene, as well as the total amount of six detected volatile compounds. Girdling did not affect the levels of these volatiles. Emerald ash borer females preferred mature leaves, leaves from girdled trees, and leaves grown in the sun over young leaves, leaves from nongirdled trees, and leaves grown in the shade, respectively. These emerald ash borer preferences were most likely because of physical, nutritional, or biochemical changes in leaves in response to the different treatments. Emerald ash borer females and males showed positive phototaxis in laboratory arenas, a response consistent with emerald ash borer preference for host trees growing in sunlight.

10 Risk to Ash from Emerald Ash Borer: Can Biological Control Prevent the Loss of Ash Stands

Science.gov (United States)

Ash trees were once relatively free of serious, major diseases and insect pests in North America until the arrival of EAB, which was first detected in North America in Michigan in 2002. As of February 2014, EAB had been detected in 22 U.S. states and two Canadian provinces, killing millions of ash ...

Processed bottom ash for replacing fine aggregate in making high-volume fly ash concrete

OpenAIRE

Antoni; Sulistio Aldi Vincent; Wahjudi Samuel; Hardjito Djwantoro; Hardjito Djwantoro

2017-01-01

Bottom ash is a coal plant by-product that is abundant and underutilized. There is the potential use of bottom ash as a fine aggregate replacement in concrete mixtures; however, the problems of water absorption and uniformity of quality of the material need to be overcome first. In this study, bottom ash was treated by sieve separation and pounding to smaller particle size for use as a sand substitute. The physical and chemical characteristics of bottom ash were tested after treatment includi...

Characterization of metals released from coal fly ash during dredging at the Kingston ash recovery project.

Science.gov (United States)

Bednar, A J; Averett, D E; Seiter, J M; Lafferty, B; Jones, W T; Hayes, C A; Chappell, M A; Clarke, J U; Steevens, J A

2013-09-01

A storage-pond dike failure occurred on December 22, 2008 at the Tennessee Valley Authority Kingston Fossil Plant resulting in the release of over 4million cubic meters (5million cubic yards) of fly ash. Approximately half of the released ash was deposited in the main channel of the Emory River, Tennessee, USA. Remediation efforts of the Emory River focused on hydraulic dredging, as well as mechanical excavation in targeted areas. However, agitation of the submerged fly ash during hydraulic dredging introduces river water into the fly ash material, which could promote dissolution and desorption of metals from the solid fly ash material. Furthermore, aeration of the dredge slurry could alter the redox state of metals in the fly ash material and thereby change their sorption, mobility, and toxicity properties. The research presented here focuses on the concentrations and speciation of metals during the fly ash recovery from the Emory River. Our results indicate that arsenite [As(III)] released from the fly ash material during dredging was slowly oxidized to arsenate [As(V)] in the slurry recovery system with subsequent removal through precipitation or sorption reactions with suspended fly ash material. Concentrations of other dissolved metals, including iron and manganese, also generally decreased in the ash recovery system prior to water discharge back to the river. Published by Elsevier Ltd.

Prospects for ash pond reclamation

Energy Technology Data Exchange (ETDEWEB)

Shyyam, A.K.; Shukla, K.S.; Agrawal, D. (National Thermal Power Corporation Ltd., New Delhi (India))

1993-01-01

A typical modern coal fired station in India burns 0.7 t/MWh of coal and consequently generates ash at 0.245 t/MWh. The physical nature of ash, low available concentrations of certain plant nutrients and the presence of phytotoxic trace elements render fly ash marginally adequate for plant growth. As fly ash itself was thought to be an inappropriate growth medium for plants, regulators decided that a soil cover is mandatory. There is ample data to suggest that the attributes of fly ash detrimental to plant growth can be ameliorated, allowing the establishment of vegetation directly on fly ash surfaces. The natural revegetation of fly ash disposal sites has been reported in the world. The natural vegetation pioneered by Cynodon at different stages of ecological succession and comprising of species such as [ital Calotropis gigantea], [ital Lippia nodiflora], [ital Ipomea, cornea], [ital Xanthium parviflorum] has been noted at one of the NTPC projects, in Badarpur Thermal Power Station. Since natural reclamation is a time-consuming process, experimental trials of growing some species over the temporary ash lagoon directly (without soil cover) were carried out at Ramagundam Super Thermal Power Project (RSTPP) of NTPC, in South India to achieve faster results than the natural process. 6 refs., 8 figs.

[Comparative study of 3 types of lancets for performing prick tests].

Science.gov (United States)

Montalvo, A; Martín, S; Mesa, A; Cortés, C; Rodríguez, M; Laso, M T

1996-01-01

Skin Prick Test is considered the cutaneous test of choice in rutinary clinical practice as well as in research. In the last 15 years a large number of lancets for puncture test have been developed looking for a higher level of standardisation and reproducibility. We have compared three lancets, two of them, NeoAbelló (NA) and Dome/Hollister Stier (DHS), used in puncture test and a third one, Blood Lancet (BL), in the modified prick test. Twenty-two patients sensitised to Phleum pratense were tested with the three lancets at three extract concentrations and histamine 10 mg/mL in duplicate. We compared their wheal sizes by means of parallel line assay, their reproducibility, frequency of bleeding wheals, the disturbance for the patient and the correlation between specific IgE and skin response. Wheal size was similar for puncture tests (DHS and NA lancets) and significatively lower than BL, being necessary to increase 1.9 times the extract concentration when using DHS and NA lancets to achieve the same wheal size than when using BL lancets (p < 0.01). Reproducibility with histamine was similar with the three lancets while with the extract was somehow better with puncture tests but without statistical significance. Bleeding was significantly more frequent with BL although this did not influence the results. Less pain was obtained with BL. Finally, correlation with specific IgE was slightly significant for NA and very similar for the other two. With these results in mind we think that any of the three lancets is valid for the diagnostic of the allergic patient. Nevertheless, puncture tests are probably the most suitable at a research level.

Radioisotope conveyor ash meter

International Nuclear Information System (INIS)

Savelov, V.D.

1994-01-01

Radioisotope conveyor ash meter realizes persistent measuring of ashiness of coal and products of its enrichment on the belt conveyor without contact. The principle of ash meter acting is based on functional dependence of the gamma radiation flows backscattering intensity of radioisotope sources from the ash volume content in the controlled fuel. Facility consists from the ashiness transducer and the processing and control device

Bioleaching of trace metals from coal ash using local isolate from coal ash ponds

Directory of Open Access Journals (Sweden)

Pangayao Denvert

2018-01-01

Full Text Available Bioleaching of chromium, copper, manganese and zinc from coal ash were investigated using isolates from coal ash ponds particularly Psuedomonas spp. Six (6 different coal ash ponds were examined however, after initial screening Psuedomonas spp. were only present in three (3 coal ash ponds. Among the three coal ash ponds, results showed that eight (8 putative Pseudomonas spp. isolates were present that were identified using the Polymerase Chain Reaction (PCR. Using the eight putative Pseudomonas spp. for bioleaching at optimum conditions and 15 days, the pH value ranges from 8.26 to 8.84 which was basic in nature. Moreover, the maximum metal leached were 8.04% Cr, 12.05% Cu, 4.34% Mn and 10.63% Zn.

Proficiency testing of skin prick testers as part of a quality assurance system

DEFF Research Database (Denmark)

Malling, Hans-Jørgen; Allesen-Holm, Pernille; Karved, Lisbeth Sys

2016-01-01

BACKGROUND: Skin prick test is an important diagnostic procedure in clinical allergy but documentation of the quality is often missing. METHODS: We describe a proficiency system to evaluate staff members in relation to the international recommended reproducibility in terms of coefficient...... of variation (CV 0.85) based on blinded octuplicate histamine testing using histamine 3, 10, 30 and 100 mg/ml. RESULTS: Fourteen trained allergy nurses participated in the proficiency testing. More than 95 % of the nurses, generated coefficient of variation...

Prescription for herbal healing

National Research Council Canada - National Science Library

Balch, Phyllis A; Bell, Stacey J

2012-01-01

.... John's Wort, to less familiar remedies, such as khella and prickly ash Chinese and ayurvedic herbal combinations Discussion of more than 150 common disorders from acne to yeast infection, and suggested herbal treatment therapies"--

Optimizing and Characterizing Geopolymers from Ternary Blend of Philippine Coal Fly Ash, Coal Bottom Ash and Rice Hull Ash

Directory of Open Access Journals (Sweden)

Martin Ernesto Kalaw

2016-07-01

Full Text Available Geopolymers are inorganic polymers formed from the alkaline activation of amorphous alumino-silicate materials resulting in a three-dimensional polymeric network. As a class of materials, it is seen to have the potential of replacing ordinary Portland cement (OPC, which for more than a hundred years has been the binder of choice for structural and building applications. Geopolymers have emerged as a sustainable option vis-à-vis OPC for three reasons: (1 their technical properties are comparable if not better; (2 they can be produced from industrial wastes; and (3 within reasonable constraints, their production requires less energy and emits significantly less CO2. In the Philippines, the use of coal ash, as the alumina- and silica- rich geopolymer precursor, is being considered as one of the options for sustainable management of coal ash generation from coal-fired power plants. However, most geopolymer mixes (and the prevalent blended OPC use only coal fly ash. The coal bottom ash, having very few applications, remains relegated to dumpsites. Rice hull ash, from biomass-fired plants, is another silica-rich geopolymer precursor material from another significantly produced waste in the country with only minimal utilization. In this study, geopolymer samples were formed from the mixture of coal ash, using both coal fly ash (CFA and coal bottom ash (CBA, and rice hull ash (RHA. The raw materials used for the geopolymerization process were characterized using X-ray fluorescence spectroscopy (XRF for elemental and X-ray diffraction (XRD for mineralogical composition. The raw materials’ thermal stability and loss on ignition (LOI were determined using thermogravimetric analysis (TGA and reactivity via dissolution tests and inductively-coupled plasma mass spectrometry (ICP analysis. The mechanical, thermal and microstructural properties of the geopolymers formed were analyzed using compression tests, Fourier transform infra-red spectroscopy (FTIR

Optimizing and Characterizing Geopolymers from Ternary Blend of Philippine Coal Fly Ash, Coal Bottom Ash and Rice Hull Ash.

Science.gov (United States)

Kalaw, Martin Ernesto; Culaba, Alvin; Hinode, Hirofumi; Kurniawan, Winarto; Gallardo, Susan; Promentilla, Michael Angelo

2016-07-15

Geopolymers are inorganic polymers formed from the alkaline activation of amorphous alumino-silicate materials resulting in a three-dimensional polymeric network. As a class of materials, it is seen to have the potential of replacing ordinary Portland cement (OPC), which for more than a hundred years has been the binder of choice for structural and building applications. Geopolymers have emerged as a sustainable option vis-à-vis OPC for three reasons: (1) their technical properties are comparable if not better; (2) they can be produced from industrial wastes; and (3) within reasonable constraints, their production requires less energy and emits significantly less CO₂. In the Philippines, the use of coal ash, as the alumina- and silica- rich geopolymer precursor, is being considered as one of the options for sustainable management of coal ash generation from coal-fired power plants. However, most geopolymer mixes (and the prevalent blended OPC) use only coal fly ash. The coal bottom ash, having very few applications, remains relegated to dumpsites. Rice hull ash, from biomass-fired plants, is another silica-rich geopolymer precursor material from another significantly produced waste in the country with only minimal utilization. In this study, geopolymer samples were formed from the mixture of coal ash, using both coal fly ash (CFA) and coal bottom ash (CBA), and rice hull ash (RHA). The raw materials used for the geopolymerization process were characterized using X-ray fluorescence spectroscopy (XRF) for elemental and X-ray diffraction (XRD) for mineralogical composition. The raw materials' thermal stability and loss on ignition (LOI) were determined using thermogravimetric analysis (TGA) and reactivity via dissolution tests and inductively-coupled plasma mass spectrometry (ICP) analysis. The mechanical, thermal and microstructural properties of the geopolymers formed were analyzed using compression tests, Fourier transform infra-red spectroscopy (FTIR), scanning

Effects of the addition of oil shale ash and coal ash on physic-chemical properties of CPJ45 cement

Directory of Open Access Journals (Sweden)

Nabih K.

2014-04-01

Full Text Available We focused our research on recycling industrial wastes, fly ash (F.A, bottom ash (B.A and oil shale ash (S.A in cement production. The study concerns physico-chemical characterization of these products and the influence of their addition on the mechanical proprieties of the CPJ45 cement. XRF allowed us to rank the three additives used according to their contents on major oxides. Coal ashes belong to the class F, and thus possess poozzolanic properties and oil shale ash belongs to the class C and possesses hydraulic and poozolanic properties. The crystalline phases constituting each ash were analysed by XRD. We observe in bottom ash the presence of quartz and mullite. The same crystals are found in fly ash with hematite and magnetite. Oil shale ash is composed of quartz, anhydrite, gehlenite, wollastonite and periclase. The microstructures of fly ash and bottom ash were studied using SEM. The bottom ash was composed respectively of fine particles that are generally irregularly shaped, their dimensions are between 5 and 28μm and of big particles(300 μm. The EDX analysis coupled with an electronic microscope provided some information about the major elements that constitute our samples. The dehydrations of anhydrous and three days hydrated cement were examined by DSC. For hydrated cements we noticed endothermic peaks related to the dehydration of CSH, CH and decomposition of carbonates. The study of the mechanical properties of CPJ45 cement by adding different proportions of fly ash, bottom ash and oil shale ash helped clarifying the percentage of ash that leaded to improve the 28 days mechanical strength. The results show that the cements studied have their maximum mechanical resistance with the addition at 7% of fly ash or 10% of oil shale ash.

Fly ash dynamics in soil-water systems

International Nuclear Information System (INIS)

Sharma, S.; Fulekar, M.H.; Jayalakshmi, C.P.

1989-01-01

Studies regarding the effluents and coal ashes (or fly ash) resulting from coal burning are numerous, but their disposal and interactions with the soil and water systems and their detailed environmental impact assessment with concrete status reports on a global scale are scanty. Fly ash dynamics in soil and water systems are reviewed. After detailing the physical composition of fly ash, physicochemical changes in soil properties due to fly ash amendment are summarized. Areas covered include texture and bulk density, moisture retention, change in chemical equilibria, and effects of fly ash on soil microorganisms. Plant growth in amended soils is discussed, as well as plant uptake and accumulation of trace elements. In order to analyze the effect of fly ash on the physicochemical properties of water, several factors must be considered, including surface morphology of fly ash, pH of the ash sluice water, pH adjustments, leachability and solubility, and suspended ash and settling. The dynamics of fly ash in water systems is important due to pollution of groundwater resources from toxic components such as trace metals. Other factors summarized are bioaccumulation and biomagnification, human health effects of contaminants, and the impact of radionuclides in fly ash. Future research needs should focus on reduction of the environmental impact of fly ash and increasing utilization of fly ash as a soil amendment. 110 refs., 2 figs., 10 tabs

Fly ash quality and utilization

Energy Technology Data Exchange (ETDEWEB)

Barta, L.E.; Lachner, L.; Wenzel, G.B. [Inst. for Energy, Budapest (Hungary); Beer, M.J. [Massachusetts Inst. of Technology, Cambridge, MA (United States)

1995-12-01

The quality of fly ash is of considerable importance to fly ash utilizers. The fly ash puzzolanic activity is one of the most important properties that determines the role of fly ash as a binding agent in the cementing process. The puzzolanic activity, however is a function of fly ash particle size and chemical composition. These parameters are closely related to the process of fly ash formation in pulverized coal fired furnaces. In turn, it is essential to understand the transformation of mineral matter during coal combustion. Due to the particle-to-particle variation of coal properties and the random coalescence of mineral particles, the properties of fly ash particles e.g. size, SiO{sub 2} content, viscosity can change considerably from particle to particle. These variations can be described by the use of the probability theory. Since the mean values of these randomly changing parameters are not sufficient to describe the behavior of individual fly ash particles during the formation of concrete, therefore it is necessary to investigate the distribution of these variables. Examples of these variations were examined by the Computer Controlled Scanning Electron Microscopy (CCSEM) for particle size and chemical composition for Texas lignite and Eagel Butte mineral matter and fly ash. The effect of combustion on the variations of these properties for both the fly ash and mineral matter were studied by using a laminar flow reactor. It is shown in our paper, that there are significant variations (about 40-50% around the mean values) of the above-listed properties for both coal samples. By comparing the particle size and chemical composition distributions of the mineral matter and fly ash, it was possible to conclude that for the Texas lignite mineral matter, the combustion did not effect significantly the distribution of these properties, however, for the Eagel Butte coal the combustion had a major impact on these mineral matter parameters.

Ash cloud aviation advisories

Energy Technology Data Exchange (ETDEWEB)

Sullivan, T.J.; Ellis, J.S. [Lawrence Livermore National Lab., CA (United States); Schalk, W.W.; Nasstrom, J.S. [EG and G, Inc., Pleasanton, CA (United States)

1992-06-25

During the recent (12--22 June 1991) Mount Pinatubo volcano eruptions, the US Air Force Global Weather Central (AFGWC) requested assistance of the US Department of Energy`s Atmospheric Release Advisory Capability (ARAC) in creating volcanic ash cloud aviation advisories for the region of the Philippine Islands. Through application of its three-dimensional material transport and diffusion models using AFGWC meteorological analysis and forecast wind fields ARAC developed extensive analysis and 12-hourly forecast ash cloud position advisories extending to 48 hours for a period of five days. The advisories consisted of ``relative`` ash cloud concentrations in ten layers (surface-5,000 feet, 5,000--10,000 feet and every 10,000 feet to 90,000 feet). The ash was represented as a log-normal size distribution of 10--200 {mu}m diameter solid particles. Size-dependent ``ashfall`` was simulated over time as the eruption clouds dispersed. Except for an internal experimental attempt to model one of the Mount Redoubt, Alaska, eruptions (12/89), ARAC had no prior experience in modeling volcanic eruption ash hazards. For the cataclysmic eruption of 15--16 June, the complex three-dimensional atmospheric structure of the region produced dramatically divergent ash cloud patterns. The large eruptions (> 7--10 km) produced ash plume clouds with strong westward transport over the South China Sea, Southeast Asia, India and beyond. The low-level eruptions (< 7 km) and quasi-steady-state venting produced a plume which generally dispersed to the north and east throughout the support period. Modeling the sequence of eruptions presented a unique challenge. Although the initial approach proved viable, further refinement is necessary and possible. A distinct need exists to quantify eruptions consistently such that ``relative`` ash concentrations relate to specific aviation hazard categories.

Identifying glass compositions in fly ash

Directory of Open Access Journals (Sweden)

Katherine eAughenbaugh

2016-01-01

Full Text Available In this study, four Class F fly ashes were studied with a scanning electron microscope; the glassy phases were identified and their compositions quantified using point compositional analysis with k-means clustering and multispectral image analysis. The results showed that while the bulk oxide contents of the fly ashes were different, the four fly ashes had somewhat similar glassy phase compositions. Aluminosilicate glasses (AS, calcium aluminosilicate glasses (CAS, a mixed glass, and, in one case, a high iron glass were identified in the fly ashes. Quartz and iron crystalline phases were identified in each fly ash as well. The compositions of the three main glasses identified, AS, CAS, and mixed glass, were relatively similar in each ash. The amounts of each glass were varied by fly ash, with the highest calcium fly ash containing the most of calcium-containing glass. Some of the glasses were identified as intermixed in individual particles, particularly the calcium-containing glasses. Finally, the smallest particles in the fly ashes, with the most surface area available to react in alkaline solution, such as when mixed with portland cement or in alkali-activated fly ash, were not different in composition than the large particles, with each of the glasses represented. The method used in the study may be applied to a fly ash of interest for use as a cementing material in order to understand its potential for reactivity.

The Role of Biocontrol of Emerald Ash Borer in Protecting Ash Regeneration after Invasion

Science.gov (United States)

Emerald ash borer (EAB) is an invasive Asian beetle that is destroying ash in forests over much of eastern North America because of the high susceptibility of our native ash and a lack of effective natural enemies. To increase mortality of EAB larvae and eggs, the USDA (FS, ARS and APHIS) is carryin...

Study of a large rapid ashing apparatus and a rapid dry ashing method for biological samples and its application

International Nuclear Information System (INIS)

Jin Meisun; Wang Benli; Liu Wencang

1988-04-01

A large rapid-dry-ashing apparatus and a rapid ashing method for biological samples are described. The apparatus consists of specially made ashing furnace, gas supply system and temperature-programming control cabinet. The following adventages have been showed by ashing experiment with the above apparatus: (1) high speed of ashing and saving of electric energy; (2) The apparatus can ash a large amount of samples at a time; (3) The ashed sample is pure white (or spotless), loose and easily soluble with few content of residual char; (4) The fresh sample can also be ashed directly. The apparatus is suitable for ashing a large amount of the environmental samples containing low level radioactivity trace elements and the medical, food and agricultural research samples

Leaf, stem bark and fruit anatomy of zanthoxylum armatum dc. (rutaceae)

International Nuclear Information System (INIS)

Barkatullah, A.; Ibrar, M.; Jelani, G.; Ahmad, I.

2014-01-01

Zanthoxylum armatum DC. (Rutaceae) is an important medicinal plant. The present study deals with anatomical exploration of the leaf, stem bark and fruit of this plant. Leaf of Z. armatum is bifacial, compound and punctate with glabrous surfaces having a single layer of epidermis and palisade mesophyll. The leaf has a Palisade ratio ranged from 6.00 to 9.00 (8.2 +- 0.32). Vein islets and vein termination number were 14-21 (16.8 +- 0.64) and 17-21 (19.1 +- 0.43) per mm2 respectively. The vein-islets were quite distinct with squaresh, elongated, polygonal or irregular in shape bounding many forked and unforked vascular branches. Adaxial surface of Z. armatum leaf midrib was planoconvex while the abaxial surface was semicircular in appearance. The diagnostic feature of the leaf was the complete absence of any kind of trichomes or any other appendages. The leaf showed prominent oil cavities. Nine types of stomata with different frequencies and other dimensions were observed. Brachparatetracytic stomata was the most frequent stoma (80%) followed by actinostephanocytic (40%) and then straucytic and brachyparacytic (30%) each. Hemiparacytic and stomatal cluster were the rarely occurring stomata (10% each) present on the lower epidermis of the leaf. Stomatal cluster, which is considered to be a special leaf epidermal feature and reported only in few genera of vascular plants, was also recorded in this plant. Bark and fruit anatomy of Z. armatum showed different tissue arrangement. The seed was non endospermic and contains an elongated embryo. The present study will be helpful in the phylogeny and taxonomic description of this important medicinal plant. (author)

A pilot evaluation of whole blood finger-prick sampling for point-of-care HIV viral load measurement: the UNICORN study.

Science.gov (United States)

Fidler, Sarah; Lewis, Heather; Meyerowitz, Jodi; Kuldanek, Kristin; Thornhill, John; Muir, David; Bonnissent, Alice; Timson, Georgina; Frater, John

2017-10-20

There is a global need for HIV viral load point-of-care (PoC) assays to monitor patients receiving antiretroviral therapy. UNICORN was the first study of an off-label protocol using whole blood finger-prick samples tested with and without a simple three minute spin using a clinic-room microcentrifuge. Two PoC assays were evaluated in 40 HIV-positive participants, 20 with detectable and 20 with undetectable plasma viral load (pVL) (<20 copies/ml). Using 100 µl finger-prick blood samples, the Cepheid Xpert HIV-1 Viral Load and HIV-1 Qual cartridges were compared with laboratory pVL assessment (TaqMan, Roche). For participants with undetectable viraemia by TaqMan, there was poor concordance without centrifugation with the TaqMan platform with only 40% 'undetectable' using Xpert VL and 25% 'not detected' using the Qual assay. After a 3 minute spin, 100% of samples were undetectable using either assay, showing full concordance with the TaqMan assay. Defining a lower limit of detection of 1000 copies/ml when including a spin, there was 100% concordance with the TaqMan platform with strong correlation (rho 0.95 and 0.94; p < 0.0001 for both assays). When including a simple microcentrifugation step, finger-prick PoC testing was a quick and accurate approach for assessing HIV viraemia, with excellent concordance with validated laboratory approaches.

Volcanic ash impacts on critical infrastructure

Science.gov (United States)

Wilson, Thomas M.; Stewart, Carol; Sword-Daniels, Victoria; Leonard, Graham S.; Johnston, David M.; Cole, Jim W.; Wardman, Johnny; Wilson, Grant; Barnard, Scott T.

2012-01-01

Volcanic eruptions can produce a wide range of hazards. Although phenomena such as pyroclastic flows and surges, sector collapses, lahars and ballistic blocks are the most destructive and dangerous, volcanic ash is by far the most widely distributed eruption product. Although ash falls rarely endanger human life directly, threats to public health and disruption to critical infrastructure services, aviation and primary production can lead to significant societal impacts. Even relatively small eruptions can cause widespread disruption, damage and economic loss. Volcanic eruptions are, in general, infrequent and somewhat exotic occurrences, and consequently in many parts of the world, the management of critical infrastructure during volcanic crises can be improved with greater knowledge of the likely impacts. This article presents an overview of volcanic ash impacts on critical infrastructure, other than aviation and fuel supply, illustrated by findings from impact assessment reconnaissance trips carried out to a wide range of locations worldwide by our international research group and local collaborators. ‘Critical infrastructure’ includes those assets, frequently taken for granted, which are essential for the functioning of a society and economy. Electricity networks are very vulnerable to disruption from volcanic ash falls. This is particularly the case when fine ash is erupted because it has a greater tendency to adhere to line and substation insulators, where it can cause flashover (unintended electrical discharge) which can in turn cause widespread and disruptive outages. Weather conditions are a major determinant of flashover risk. Dry ash is not conductive, and heavy rain will wash ash from insulators, but light rain/mist will mobilise readily-soluble salts on the surface of the ash grains and lower the ash layer’s resistivity. Wet ash is also heavier than dry ash, increasing the risk of line breakage or tower/pole collapse. Particular issues for water

Modeling the effects of temperature and relative humidity on gas exchange of prickly pear cactus (Opuntia spp.) stems

NARCIS (Netherlands)

Guevara-Arauza, J.C.; Yahia, E.M.; Cedeno, L.; Tijskens, L.M.M.

2006-01-01

A model to estimate gas profile of modified atmosphere packaged (MAP) prickly pear cactus stems was developed and calibrated. The model describes the transient gas exchange taking in consideration the effect of temperature (T) and relative humidity (RH) on film permeability (FPgas), respiration rate

Transcriptomic signatures of ash (Fraxinus spp. phloem.

Directory of Open Access Journals (Sweden)

Xiaodong Bai

2011-01-01

Full Text Available Ash (Fraxinus spp. is a dominant tree species throughout urban and forested landscapes of North America (NA. The rapid invasion of NA by emerald ash borer (Agrilus planipennis, a wood-boring beetle endemic to Eastern Asia, has resulted in the death of millions of ash trees and threatens billions more. Larvae feed primarily on phloem tissue, which girdles and kills the tree. While NA ash species including black (F. nigra, green (F. pennsylvannica and white (F. americana are highly susceptible, the Asian species Manchurian ash (F. mandshurica is resistant to A. planipennis perhaps due to their co-evolutionary history. Little is known about the molecular genetics of ash. Hence, we undertook a functional genomics approach to identify the repertoire of genes expressed in ash phloem.Using 454 pyrosequencing we obtained 58,673 high quality ash sequences from pooled phloem samples of green, white, black, blue and Manchurian ash. Intriguingly, 45% of the deduced proteins were not significantly similar to any sequences in the GenBank non-redundant database. KEGG analysis of the ash sequences revealed a high occurrence of defense related genes. Expression analysis of early regulators potentially involved in plant defense (i.e. transcription factors, calcium dependent protein kinases and a lipoxygenase 3 revealed higher mRNA levels in resistant ash compared to susceptible ash species. Lastly, we predicted a total of 1,272 single nucleotide polymorphisms and 980 microsatellite loci, among which seven microsatellite loci showed polymorphism between different ash species.The current transcriptomic data provide an invaluable resource for understanding the genetic make-up of ash phloem, the target tissue of A. planipennis. These data along with future functional studies could lead to the identification/characterization of defense genes involved in resistance of ash to A. planipennis, and in future ash breeding programs for marker development.

Spectral analysis of white ash response to emerald ash borer infestations

Science.gov (United States)

Calandra, Laura

The emerald ash borer (EAB) (Agrilus planipennis Fairmaire) is an invasive insect that has killed over 50 million ash trees in the US. The goal of this research was to establish a method to identify ash trees infested with EAB using remote sensing techniques at the leaf-level and tree crown level. First, a field-based study at the leaf-level used the range of spectral bands from the WorldView-2 sensor to determine if there was a significant difference between EAB-infested white ash (Fraxinus americana) and healthy leaves. Binary logistic regression models were developed using individual and combinations of wavelengths; the most successful model included 545 and 950 nm bands. The second half of this research employed imagery to identify healthy and EAB-infested trees, comparing pixel- and object-based methods by applying an unsupervised classification approach and a tree crown delineation algorithm, respectively. The pixel-based models attained the highest overall accuracies.

Thermal treatment of ashes[Fly Ash from Municipal Waste Incineration]; Termisk rening av askor

Energy Technology Data Exchange (ETDEWEB)

Wikman, Karin; Berg, Magnus; Bjurstroem, Henrik [AaF-Energi och Miljoe AB, Stockholm (Sweden); Nordin, Anders [Umeaa Univ. (Sweden). Dept. of Applied Physics and Electronics

2003-04-01

In this project descriptions of different processes for thermal treatment of ashes have been compiled. A technical and economic evaluation of the processes has been done to identify possibilities and problems. The focus in the project lays on treatment of fly ash from municipal waste incineration but the processes can also be used to treat other ashes. When the ash is heated in the thermal treatment reactor, with or without additives, the material is sintered or vitrified and at the same time volatile substances (Zn, Pb, Cd, Hg etc.) are separated. In general the separation is more effective in processes with reducing conditions compared to oxidizing conditions. Oxidizing processes have both worse separation capacity and require more energy. The oxidizing processes are mainly used to stabilize the ash through vitrification and they are in some cases developed for management of municipal sewage sludge and bottom ash. However, these processes are often not as complex as for example an electric arc melting furnace with reducing conditions. The research today aim to develop more effective electrical melting systems with reducing conditions such as plasma melting furnaces, electric resistance melting furnaces and low frequency induction furnaces. A central question in the evaluation of different thermal treatment processes for ash is how the residues from the treatment can be used. It is not certain that the vitrified material is stable enough to get a high economic value, but it can probably be used as construction material. How the remaining metals in the ash are bound is very important in a long-time perspective. Further studies with leaching tests are necessary to clarify this issue. The heavy metal concentrate from the processes contains impurities, such as chlorine, which makes it unprofitable to obtain the metals. Instead the heavy metal concentrate has to be land filled. However, the amount of material for land filling will be much smaller if only the heavy

Application of Coal Ash to Postmine Land for Prevention of Soil Erosion in Coal Mine in Indonesia: Utilization of Fly Ash and Bottom Ash

Directory of Open Access Journals (Sweden)

Shinji Matsumoto

2016-01-01

Full Text Available The increase in the number of coal-fired power plants with the increase in coal production and its consumption has caused the problem of the treatment of a large amount of coal ash in Indonesia. In the past studies, coal ash was applied to postmine land with the aim of improving soil conditions for plant growth; however, heavy rain in the tropical climate may cause soil erosion with the change in soil conditions. This study presents the effects of application of coal ash to postmine land on soil erosion by performing the artificial rainfall test as well as physical testing. The results indicate that the risk of soil erosion can be reduced significantly by applying the coal ash which consists of more than 85% of sand to topsoil in the postmine land at the mixing ratio of over 30%. Additionally, they reveal that not only fine fractions but also microporous structures in coal ash enhance water retention capacity by retaining water in the structure, leading to the prevention of soil erosion. Thus, the risk of soil erosion can be reduced by applying coal ash to topsoil in consideration of soil composition and microporous structure of coal ash.

Possibilities of utilizing power plant fly ashes

Directory of Open Access Journals (Sweden)

Mezencevová Andrea

2003-09-01

Full Text Available The burning of fossil fuels in industrial power stations plays a significant role in the production of thermal and electrical energy. Modern thermal power plants are producing large amounts of solid waste, mainly fly ashes. The disposal of power plant waste is a large environmental problem at the present time. In this paper, possibilities of utilization of power plant fly ashes in industry, especially in civil engineering, are presented. The fly ash is a heterogeneous material with various physical, chemical and mineralogical properties, depending on the mineralogical composition of burned coal and on the used combustion technology. The utilization of fly ashes is determined of their properties. The fineness, specific surface area, particle shape, density, hardness, freeze-thaw resistance, etc. are decisive. The building trade is a branch of industry, which employs fly ash in large quantities for several decades.The best utilization of fluid fly ashes is mainly in the production of cement and concrete, due to the excellent pozzolanic and cementitious properties of this waste. In the concrete processing, the fly ash is utilized as a replacement of the fine aggregate (fine filler or a partial replacement for cement (active admixture. In addition to economic and ecological benefits, the use of fly ash in concrete improves its workability and durability, increases compressive and flexural strength, reduces segregation, bleeding, shrinkage, heat evolution and permeability and enhances sulfate resistance of concrete.The aim of current research is to search for new technologies for the fly ash utilization. The very interesting are biotechnological methods to recovery useful components of fly ashes and unconventional methods of modification of fly ash properties such as hydrothermal zeolitization and mechanochemical modification of its properties. Mechanochemistry deals with physico - chemical transformations and chemical reactions of solids induced by

Phytochemical characterization of different prickly pear (Opuntia ficus-indica (L.) Mill.) cultivars and botanical parts: UHPLC-ESI-MSn metabolomics profiles and their chemometric analysis.

Science.gov (United States)

Mena, Pedro; Tassotti, Michele; Andreu, Lucía; Nuncio-Jáuregui, Nallely; Legua, Pilar; Del Rio, Daniele; Hernández, Francisca

2018-06-01

Prickly pear is an important source of bioactive compounds. However, a comprehensive characterization of the phytochemical profile of its aerial botanical parts, considering genotypic differences, has not been conducted. This study evaluated the phytochemical composition of four botanical parts (fruit pulp and skin, and young and adult cladodes) of six cultivars. Analysis was carried out by using two non-targeted UHPLC-ESI-MS n experimental conditions and assisted with multivariate analysis to facilitate data interpretation. Up to 41 compounds, mainly (poly)phenolic molecules, were identified and quantified, 23 compounds being reported for the first time in Opuntia ficus-indica. Phenolic composition varied significantly depending on the part of the plant. Betalains were detected only in the fruit of a red cultivar. This study provided novel insights in terms of identification of bioactives and thorough characterization of botanical parts of prickly pears. This information may be used for the development of prickly pear-derived products with high levels of bioactive compounds. Copyright © 2018 Elsevier Ltd. All rights reserved.

Rapid Determination of the Geographical Origin of Chinese Red Peppers (Zanthoxylum Bungeanum Maxim. Based on Sensory Characteristics and Chemometric Techniques

Directory of Open Access Journals (Sweden)

Xiangqian Yin

2018-04-01

Full Text Available In this paper, principal component analysis (PCA, linear discriminant analysis (LDAp, artificial neural networks (ANN, and support vector machine (SVM were applied to discriminate the geographical origin of Chinese red peppers (Zanthoxylum bungeanum Maxim.. The models based on color, smell and taste may discriminate quickly and effectively the geographical origin of Chinese red peppers from different regions, but the successful identification rates may vary with different kinds of parameters and chemometric methods. Among them, all models based on taste indexes showed an excellent ability to discriminate the geographical origin of Chinese red peppers with correct classifications of 100% for the training set and the 100% for test set. The present study provided a simple, efficient, inexpensive, practical and fast method to discriminate the geographical origin of Chinese red peppers from different regions, which was of great importance for both consumers and producers.

Measurement of natural activity in peat ashes

International Nuclear Information System (INIS)

Suomela, J.

1985-01-01

High proportions of radioactive materials in peat ashes may involve radiation hazards during handling and deposition of these waste materials. Measurements have been performed to determine the content of radioactive materials in ashes from peat burning. The activities in fly ash and ''solid'' ash in seven peat-fired power plants in Sweden are presented. The methods of analysing and measuring peat ashes for activity from different radionuclides are described. The activity levels in ash samples are given

Classification of pulverized coal ash

International Nuclear Information System (INIS)

Van der Sloot, H.A.; Van der Hoek, E.E.; De Groot, G.J.; Comans, R.N.J.

1992-09-01

The leachability of fifty different pulverized coal ashes from utilities in the Netherlands, Federal Republic of Germany and Belgium has been studied. Five different ashes were analyzed according to the complete standard leaching test and the results were published earlier. The examination of a wide variety of ashes under a wide range of pH and Liquid to Solid ratio (LS) conditions creates the possibility of identifying systematic trends in fly ash leaching behaviour and to identify the mechanisms controlling release. 16 figs., 2 tabs., 3 app., 25 refs

Radioactivity of wood ash; Puun tuhkan radioaktiivisuus

Energy Technology Data Exchange (ETDEWEB)

Rantavaara, A.; Moring, M

2000-01-01

STUK (Finnish Radiation and Nuclear Safety Authority) has investigated natural and artificial radioactivity in wood ash and radiation exposure from radionuclides in ash since 1996. The aim was to consider both handling of ash and different ways of using ash. In all 87 ash samples were collected from 22 plants using entirely or partially wood for their energy production in 1996-1997. The sites studied represented mostly chemical forest industry, sawmills or district heat production. Most plants used fluidised bed combustion technique. Samples of both fly ash and bottom ash were studied. The activity concentrations of radionuclides in samples of, e.g., dried fly ash from fuel containing more than 80% wood were determined. The means ranged from 2000 to less than 50 Bq kg{sup -1}, in decreasing order: {sup 137}Cs, {sup 40}K, {sup 90}Sr, {sup 210}Pb,{sup 226}Ra, {sup 232}Th, {sup 134}Cs, {sup 235}U. In bott radionuclide contents decreased in the same order as in fly ash, but were smaller, and {sup 210}Pb was hardly detectable. The NH{sub 4}Ac extractable fractions of activities for isotopes of alkaline elements (K, Cs) in bottom ash were lower than in fly ash, whereas solubility of heavier isotopes was low. Safety requirements defined by STUK in ST-guide 12.2 for handling of peat ash were fulfilled at each of the sites. Use of ash for land-filling and construction of streets was minimal during the sampling period. Increasing this type of ash use had often needed further investigations, as description of the use of additional materials that attenuate radiation. Fertilisation of forests with wood ash adds slightly to the external irradiation in forests, but will mostly decrease doses received through use of timber, berries, mushrooms and game meat. (orig.)

An improved ashing procedure for biologic sample

Energy Technology Data Exchange (ETDEWEB)

Zongmei, Wu [Zhejiang Province Enviromental Radiation Monitoring Centre (China)

1992-07-01

The classical ashing procedure in muffle was modified for biologic samples. In the modified procedure the door of muffle was open in the duration of ashing process, the ashing was accelerated and the ashing product quality was comparable to that the classical procedure. The modified procedure is suitable for ashing biologic samples in large batches.

An improved ashing procedure for biologic sample

International Nuclear Information System (INIS)

Wu Zongmei

1992-01-01

The classical ashing procedure in muffle was modified for biologic samples. In the modified procedure the door of muffle was open in the duration of ashing process, the ashing was accelerated and the ashing product quality was comparable to that the classical procedure. The modified procedure is suitable for ashing biologic samples in large batches

Treatment of fly ash for use in concrete

Science.gov (United States)

Boxley, Chett [Park City, UT

2012-05-15

A process for treating fly ash to render it highly usable as a concrete additive. A quantity of fly ash is obtained that contains carbon and which is considered unusable fly ash for concrete based upon foam index testing. The fly ash is mixed with a quantity of spray dryer ash (SDA) and water to initiate a geopolymerization reaction and form a geopolymerized fly ash. The geopolymerized fly ash is granulated. The geopolymerized fly ash is considered usable fly ash for concrete according to foam index testing. The geopolymerized fly ash may have a foam index less than 40%, and in some cases less than 20%, of the foam index of the untreated fly ash. An optional alkaline activator may be mixed with the fly ash and SDA to facilitate the geopolymerization reaction. The alkaline activator may contain an alkali metal hydroxide, carbonate, silicate, aluminate, or mixtures thereof.

Engineering properties of fly ash concrete

International Nuclear Information System (INIS)

Hilmi Mahmud

1999-01-01

This paper presents some of the engineering properties of Malaysian fly ash concrete. Workability, compressive, flexural, tensile splitting, drying shrinkage, elastic modulus and non destructive tests were performed on fly ash and control OPC concrete specimens. Data show that concrete containing 25% fly ash replacement of cement exhibit superior or similar engineering properties to that normal concrete without fly ash. These encouraging results demonstrated the technical merits of incorporating fly ash in concrete and should pave the way for wide scale use of this versatile material in the Malaysian construction industry. (author)

Treatment of fly ash for use in concrete

Science.gov (United States)

Boxley, Chett; Akash, Akash; Zhao, Qiang

2013-01-08

A process for treating fly ash to render it highly usable as a concrete additive. A quantity of fly ash is obtained that contains carbon and which is considered unusable fly ash for concrete based upon foam index testing. The fly ash is mixed with an activator solution sufficient to initiate a geopolymerization reaction and for a geopolymerized fly ash. The geopolymerized fly ash is granulated. The geopolymerized fly ash is considered usable fly ash for concrete according to foam index testing. The geopolymerized fly ash may have a foam index less than 35% of the foam index of the untreated fly ash, and in some cases less than 10% of the foam index of the untreated fly ash. The activator solution may contain an alkali metal hydroxide, carbonate, silicate, aluminate, or mixtures thereof.

Gasification of high ash, high ash fusion temperature bituminous coals

Science.gov (United States)

Liu, Guohai; Vimalchand, Pannalal; Peng, WanWang

2015-11-13

This invention relates to gasification of high ash bituminous coals that have high ash fusion temperatures. The ash content can be in 15 to 45 weight percent range and ash fusion temperatures can be in 1150.degree. C. to 1500.degree. C. range as well as in excess of 1500.degree. C. In a preferred embodiment, such coals are dealt with a two stage gasification process--a relatively low temperature primary gasification step in a circulating fluidized bed transport gasifier followed by a high temperature partial oxidation step of residual char carbon and small quantities of tar. The system to process such coals further includes an internally circulating fluidized bed to effectively cool the high temperature syngas with the aid of an inert media and without the syngas contacting the heat transfer surfaces. A cyclone downstream of the syngas cooler, operating at relatively low temperatures, effectively reduces loading to a dust filtration unit. Nearly dust- and tar-free syngas for chemicals production or power generation and with over 90%, and preferably over about 98%, overall carbon conversion can be achieved with the preferred process, apparatus and methods outlined in this invention.

Determining the ash content of coal flotation tailings using an MPOF optical ash meter

Energy Technology Data Exchange (ETDEWEB)

Sikora, T; Sliwa, J

1982-01-01

The block layout, a description of the design and principles of operation of an automatic optical, continuous action MPOF type ash meter are presented. The difference in the optical properties of coal and rock is used in the ash meter. The identification of the ash content is conducted on the basis of the spectral characteristics of reflection of a finely dispersed aqueous coal and rock suspension.

Phytochemical Profiles and Antioxidant and Antimicrobial Activities of the Leaves of Zanthoxylum bungeanum

Directory of Open Access Journals (Sweden)

Yujuan Zhang

2014-01-01

Full Text Available The ethanol crude extracts (ECE and their subfractions from Zanthoxylum bungeanum leaves were prepared and their phytochemical profiles and antioxidant and antimicrobial activities were investigated. Moreover, the effective HPLC procedure for simultaneous quantification of twelve compounds in Z. bungeanum leaves was established. The correlation between the phytochemicals and antioxidant activity was also discussed. The ethyl acetate fraction (EAF had the highest total phenolic (97.29 mmol GAE/100 g and flavonoid content (67.93 mmol QE/100 g, while the greatest total alkaloid content (4.39 mmol GAE/100 g was observed in the chloroform fraction (CF. Twelve compounds were quantified by RP-HPLC assay. EAF exhibited the highest content of quercitrin, kaempferol-3-rhamnoside, quercetin, sesamin, and nitidine chloride (125.21, 54.95, 24.36, 26.24, and 0.20 mg/g; acetone fraction (AF contained the highest content of chlorogenic acid, rutin, hyperoside, and trifolin (5.87, 29.94, 98.33, and 31.24 mg/g, while kaempferol-3-rhamnoside, xanthyletin, and sesamin were rich in CF. EAF and AF exhibited significant DPPH, ABTS radical scavenging abilities and reducing power (FRAP, whereas CF exhibited significant antifungal activity. Moreover, EAF also showed stronger antibacterial activity. In conclusion, Z. bungeanum leaves have health benefits when consumed and could be served as an accessible source for production of functional food ingredients and medicinal exploration.

Standardization of food allergen extracts for skin prick test

DEFF Research Database (Denmark)

Skamstrup Hansen, K; Bindslev-Jensen, C; Skov, P S

2001-01-01

The aim of the study was to standardize and evaluate technically optimized food allergen extracts for use in skin prick test (SPT). The standardization procedure comprised 36 allergic histories in 32 food allergic patients with 21 healthy, non-atopic individuals serving as controls. The patients...... had a history of allergic symptoms upon ingestion of either cow's milk (n=3), hen's egg (n=9), wheat (n=4), hazelnut (n=14) or cod (n=6). They also had specific IgE in serum to the food in question and a positive SPT with a fresh preparation of the food. The diagnosis had been confirmed by a double......-blind, placebo-controlled food challenge, except for the hazelnut-allergic patients. The controls were subjected to an open food challenge with all the foods to ensure tolerance. The standardization was performed by means of titrated SPT in accordance with the guidelines on biological standardization from...

Electrodialytic removal of heavy metals from fly ashes

DEFF Research Database (Denmark)

Pedersen, Anne Juul

2002-01-01

The aim of the Ph.D. work was to develop the electrodialytic remediation method for removal of heavy metals from fly ashes. The work was focused on two types of fly ashes: fly ashes from wood combustion and fly ashes from municipal solid waste incineration.......The aim of the Ph.D. work was to develop the electrodialytic remediation method for removal of heavy metals from fly ashes. The work was focused on two types of fly ashes: fly ashes from wood combustion and fly ashes from municipal solid waste incineration....

ANATOMICAL PROPERTIES AND FIBER DIMENSION OF PRICKLY ACACIA (Acacia nilotica L. FROM BALURAN NATIONAL PARK

Directory of Open Access Journals (Sweden)

Krisdianto Krisdianto

2007-07-01

Full Text Available Acacia nilotica (L. Willd. ex. Delile growing in Baluran National Park has dramatically altered the ecological balance of grasslands and thereby threatens the existence of local biodiversity. Prickly acacia is able to spread rapidly and remains uncontrollable. Baluran National Park authorization has been struggling to control this prickly acacia trees. One possible action that can be taken to encounter this problem is allowing wood based industries, and local people take advantages of this nilotica timber utilization. This paper studies the anatomical properties and fiber dimensions of nilotica timber and discusses the possible utilization of  nilotica timber.   This timber is characterized by dark brown heartwood which is clearly distinct from reddish brown color of sapwood. The denser cell wall shows attractively streaked in tangential surfaces. The length of  wood fiber decreases from pith toward periphery portion. Longitudinally, higher stem has shorter fiber. Nilotica wood has second class quality of fiber, which means its fiber is moderately thick with narrow lumen diameter. Due to small log diameter and branches, the nilotica timber is not recommended for construction material. The timber is suitable for carved and turnery products. Nilotica timber is suitable for charcoal manufacture and fuel wood due to its high calorific value.

Utilization options for fly ash, bottom ash, and slag in Eastern Europe

Energy Technology Data Exchange (ETDEWEB)

Manz, O.E.

1995-12-01

Since 1967, at least six ash utilization symposiums have been held in the United States, with papers presented by several European authors on the utilization of coal by-products in Eastern Europe. There is currently over 80,000 megawatts of installed coal-fired capacity available in that region. Unfortunately, of the 117,778,000 tonnes of fly ash, bottom ash, and slag produced in Eastern Europe in 1989, only 13% was utilized. This paper outlines the research and levels and kinds of coal by-product utilization taking place in Eastern Europe since the late 1960s.

Ash fusion temperatures and the transformations of coal ash particles to slag

Energy Technology Data Exchange (ETDEWEB)

Gupta, S.; Wall, T.F.; Creelman, R.A.; Gupta, R. [Univ. of Newcastle, Callaghan (Australia)

1996-12-31

A mechanistic study is detailed in which coal ash is heated with its shrinkage measured continuously up to a temperature of 1600{degrees}C. The temperatures corresponding to the rapid rate of shrinkage are shown to correspond to the formation of eutectics identified on phase diagrams. Samples were therefore heated to these temperatures, cooled rapidly and examined with an SEM to identify the associated chemical and physical changes. The progressive changes in the range of chemical analysis (from SEM), the extent of undissolved ash particles and porosity were then quantified and related to homogenization, viscosity and ash fusion mechanisms.

Ash fusion temperatures and the transformations of coal ash particles to slag

Energy Technology Data Exchange (ETDEWEB)

Wall, T.F.; Creelman, R.A.; Gupta, R.; Gupta, S. [Univ. of Newcastle (Australia)

1996-10-01

A mechanistic study is detailed in which coal ash is heated with the shrinkage and electrical resistance measured continuously up to a temperature of 1600{degrees}C. The temperatures corresponding to rapid rates of shrinkage are shown to correspond to the formation of eutectics identified on phase diagrams. Samples where therefore heated to these temperatures, cooled rapidly and examined with an SEM to identify the associated chemical and physical changes. The progressive changes in the range of chemical analysis (from SEM), the extent of undissolved ash particles and porosity are then quantified and related to the shrinkage events and standard ash fusion temperatures.

Fuelwood characteristics of some tropical trees of India

Energy Technology Data Exchange (ETDEWEB)

Jain, R.K. (National Botanical Research Inst., Lucknow (India))

1993-01-01

Twenty-two species growing in their natural habitat in Indian forests were collected and fuelwood properties viz. calorific value, ash, density, silica, moisture, carbon, nitrogen and volatile matter were determined and the Fuel Value Index (FVI) calculated to screen desirable species for potential production of fuelwood on marginal lands. The present study revealed that Osmanthus fragrans, Quercus incana, Machilus odoratissma, Lagertroemia indica and Punica granatum have the best fuelwood qualities among the species examined. The other species have calorific value within the acceptable limit except for Zanthoxylum alatum and Grewia tiliaefolia. (author)

The extraction of antimicrobials component of andaliman (Zanthoxylum acanthopodium DC.) and its application on catfish (Pangasius sutchi) fillet

Science.gov (United States)

Muzafri, A.; Julianti, E.; Rusmarilin, H.

2018-02-01

Andaliman (Zanthoxylum acanthopodium DC.) is a well known wild species in North Sumatera and used for seasoning in Batak’s traditional cuisine. This study was aimed to examine the phytochemical constituents of andaliman fruit extracts after simple macerated in water, methanol, ethyl acetate and hexana using qualitative phytochemical analysis, and to determine its potential antimicrobial activity against Staphylococus aureus, Escherichia coli and Salmonella sp by using agar well difussion method and minimum inhibitory concentration (MIC). Phytochemicals such as alkaloids, flavonoid, glycosides, saponins, tannins, triterpene/steroid and glycoside anthroquinones were detected in the methanol extracts, but steroids and glycisode antraquinones were absent in the ethyl acetate extract. The ethyl acetate extracts showed maximum zone of inhibition and minimum inhibitory concentration against all the experimental microorganisms. The minimum zone of inhibition was determined in hexane extracts showing less antimicrobial activity against all the experimental microorganisms. The MIC of the ethyl acetate extracts was 0,5% w/v for all tested bacteria. Apllication of ethyl acetate extracts of andaliman fruits showed effective for catfish (Pangasius Sutchi) fillet stored in refrigerator (5 °C) for 3 days.

Hazards Associated With Recent Popocatepetl Ash Emissions

Science.gov (United States)

Nieto, A.; Martin, A.; Espinasa-Pereña, R.; Ferres, D.

2013-05-01

Popocatepetl has been producing ash from small eruptions since 1994. Until 2012 about 650 small ash emissions have been recorded at the monitoring system of Popocatépetl Volcano. Ash consists mainly of glassy lithic clasts from the recent crater domes, plagioclase and pyroxene crystals, and in major eruptions, olivine and/or hornblende. Dome forming eruptions produced a fine white ash which covers the coarser ash. This fine ash consists of plagioclase, glass and cristobalite particles mostly under15 microns. During the recent crisis at Popocatépetl, April and May2012 ash fell on villages to the east and west of the volcano, reaching Mexico City (more than 20 million people) and Puebla (2 million people). In 14 cases the plumes had heights over 2 km, the largest on May 2 and 11 (3 and 4 km in height, respectively). Heavier ash fall occurred on April 13, 14, 20, and 23 and May 2, 3, 5, 11, 14, 23, 24 and 25. A database for ash fall was constructed from April 13 with field observations, reports emitted by the Centro Nacional de Comunicaciones (CENACOM), ash fall advisories received at CENAPRED and alerts from the Servicios a la Navegación en el Espacio Aéreo Mexicano (SENEAM). This aim of this database is to calculate areas affected by the ash and estimate the ash fall volume emitted by Popocatépetl in each of these events. Heavy ash fall from the May 8 to May 11 combined with reduced visibility due to fog forced to closure of the Puebla airport during various periods of time, for up to 13 hours. Domestic and international flights were cancelled. Ash eruptions have caused respiratory conditions in the state of Puebla, to the east of the volcano, since 1994 (Rojas et al, 2001), but because of the changing wind conditions in the summer mainly, some of these ash plumes go westward to towns in the State of Mexico and even Mexico City. Preliminary analyses of these eruptions indicate that some ash emissions produced increased respiratory noninfectious problems

Analysis list: ash2 [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available ash2 Larvae + dm3 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/target/ash2.1.tsv ...http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/target/ash2.5.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/target/ash2....10.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/colo/ash2.Larvae.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/colo/Larvae.gml ...

Attraction of the emerald ash borer to ash trees stressed by girdling, herbicide treatment, or wounding

Science.gov (United States)

Deborah McCullough; Therese Poland; David. Cappaert

2009-01-01

New infestations of emerald ash borer, Agrilus planipennis Fairmaire, an invasive pest native to Asia, are difficult to detect until densities build and symptoms appear on affected ash (Fraxinus spp). We compared the attraction of A. planipennis to ash trees stressed by girdling (bark and phloem removed...

Ash in fire affected ecosystems

Science.gov (United States)

Pereira, Paulo; Jordan, Antonio; Cerda, Artemi; Martin, Deborah

2015-04-01

Ash in fire affected ecosystems Ash lefts an important footprint in the ecosystems and has a key role in the immediate period after the fire (Bodi et al., 2014; Pereira et al., 2015). It is an important source of nutrients for plant recover (Pereira et al., 2014a), protects soil from erosion and controls soil hydrological process as runoff, infiltration and water repellency (Cerda and Doerr, 2008; Bodi et al., 2012, Pereira et al., 2014b). Despite the recognition of ash impact and contribution to ecosystems recuperation, it is assumed that we still have little knowledge about the implications of ash in fire affected areas. Regarding this situation we wanted to improve our knowledge in this field and understand the state of the research about fire ash around world. The special issue about "The role of ash in fire affected ecosystems" currently in publication in CATENA born from the necessity of joint efforts, identify research gaps, and discuss future cooperation in this interdisciplinary field. This is the first special issue about fire ash in the international literature. In total it will be published 10 papers focused in different aspects of the impacts of ash in fire affected ecosystems from several parts of the world: • Fire reconstruction using charcoal particles (Burjachs and Espositio, in press) • Ash slurries impact on rheological properties of Runoff (Burns and Gabet, in press) • Methods to analyse ash conductivity and sorbtivity in the laboratory and in the field (Balfour et al., in press) • Termogravimetric and hydrological properties of ash (Dlapa et al. in press) • Effects of ash cover in water infiltration (Leon et al., in press) • Impact of ash in volcanic soils (Dorta Almenar et al., in press; Escuday et al., in press) • Ash PAH and Chemical extracts (Silva et al., in press) • Microbiology (Barreiro et al., in press; Lombao et al., in press) We believe that this special issue will contribute importantly to the better understanding of

Evaluation of Zanthoxylum armatum Roxb for in vitro biological activities

Directory of Open Access Journals (Sweden)

Fiaz Alam

2017-10-01

Full Text Available Zanthoxylum armatum fruits are used traditionally as a spice in various food preparations. The aim of this study was analysis of antimicrobial, cytotoxic, phytotoxic, insecticidal, and anti-leishmanial activity. The crude extract showed 86 ± 10% antifungal activity (Agar tube dilution method against Trichophyton longifusis while n-hexane, chloroform, and aqueous-methanol fractions inhibited this pathogen by 90 ± 7, 85 ± 10 and 70 ± 9% respectively. The n-hexane and aqueous-methanol fraction also, respectively, showed 40 ± 10 and 87 ± 9% inhibition of Microsporum canis. Chloroform fraction also displayed antifungal activity against Aspergillus flavus (60 ± 10% and aqueous-methanol fraction against F. solani (40 ± 8%. The crude ethanolic extract and its chloroform and aqueous-methanol fraction exhibited significant toxicity (Brine shrimps lethality assay against brine shrimps having LC50 value of 6.66 ± 1.1, 21.4 ± 3.3 and 29.6 ± 3.9 μg/ml, respectively. The crude ethanolic extract and its n-hexane soluble portion exhibited good anti-leishmanial activity (well serial dilution method each having IC50 values of 50 ± 5 μg/ml. The crude extract and various fractions possessed excellent herbicidal activity (Lemna minor assay, and caused more than 90% inhibition of the plant growth at 1000 μg/mL. The ethanolic extract, n-hexane and chloroform soluble portions caused 90% mortality in insecticidal activity (direct contact method of Rhyzopertha dominica. The ethanolic extract and its n-hexane soluble portion, respectively, caused 80 and 90% mortality of Callosobruchus analis. The present study showed that the tested fruit extracts of Z. armatum exhibited strong antifungal, cytotoxic, phytotoxic, insecticidal, and anti-leishmanial effects.

Formation and utilization of fly ash

Energy Technology Data Exchange (ETDEWEB)

Vargyai, J

1974-01-01

General problems of slag and fly ash formation and utilization are discussed. The ever-increasing energy demand, and the comeback of coal as an energy carrier in power plants call for efficient solutions to the problem of slag and fly ash. Slag and fly ash are used for concrete in which they partly replace cement. Other possible uses are the amelioration of acid soils, fireclay manufacture, road construction, and tiles. It is possible to recover metals, such as vanadium, iron, aluminum, and radioactive materials from certain types of fly ash and slag. The utilization of fly ash is essential also with respect to the abatement of entrainment from dumps.

The influence of using volcanic ash and lime ash as filler on compressive strength in self compacting concrete

Science.gov (United States)

Karolina, Rahmi; Panatap Simanjuntak, Murydrischy

2018-03-01

Self Compacting Concrete (SCC) is a technology which is developing today in which concrete solidifies by itself without using vibrator. Casting conventional concrete which has a lot of reinforcement bars sometimes finds difficulty in achieving optimal solidity. The method used to solve this problem is by using SCC technology. SCC was made by using filler, volcanic ash, and lime ash as the filling materials so that the concrete became more solid and hollow space could be filled up. The variation of using these two materials was 10%, 15%, 20%, and 25% of the cementitious mass and using 1% of superplasticizer from cementitious material. The supporting testing was done by using the test when the concrete was still fluid and when it was solid. Malleable concrete was tested by using EFNARC 2002 standard in slump flow test, v-funnel test, l-shaped box test, and j-ring test to obtain filling ability and passing ability. In this malleable lime concrete test, there was the decrease, compared with normal SCC concrete without adding volcanic ash and lime ash. Testing was also done in solid concrete in compressive strength, tensile strength, and concrete absorption. The result of the testing showed that the optimum tensile strength in Variation 1, without volcanic ash and lime ash – with 1% of superplasticizer was 39.556 MPa, the optimum tensile strength in Variation 1, without volcanic ash and lime ash- with 1% of super-plasticizer was 3.563 MPa, while the value of optimum absorption which occurred in Variation 5 (25% of volcanic ash + 25% of lime ash + 50% of cement + 1% of superplasticizer) was 1.313%. This was caused by the addition of volcanic ash and lime ash which had high water absorption.

Wildfire Ash: Chemical Composition, Ash-Soil Interactions and Environmental Impacts

Science.gov (United States)

Brook, Anna; Hamzi, Seham; Wittenberg, Lea

2015-04-01

Of the five classical factors of soil formation, climate, parent material, topography, time, organisms, and recently recognized human activity, it is the latter factor which discretely includes fire and post-burn impact. However, it is considered that soil undergoing fire just experience a temporary removal of the top organic horizon, thus slightly modified and often labeled as 'temporarily disturbed' soil or soil 'under restoration/rehabilitation'. In fact the suggested seventh factor, post-burned produced ash, can act both dependently and independently of the other soil forming factors (Levin et al., 2013; Certini 2013). They are interdependent in cases where ash influences occur on time scales similar to 'natural' soil formation (Keesstra et ai., 2014) such as changes in vegetation. On the other hand, in post-fire areas a strong dependency is expected between soil-water retention mechanism, climate and topography. Wild-land fires exert many changes on the physical, chemical, mineralogical, biological, and morphological properties of soil that, in turn, affect the soil's hydrology and nutrient flux, modifying its ability to support vegetation and resist erosion. The ash produced by forest fires is a complex mixture composed of organic and inorganic particles characterized by vary physical-chemical and morphological properties. The importance of this study is straightforwardly related to the frequency and large-scales wildfires in Mediterranean region. In fact, wildfires are major environmental and land management concern in the world, where the number and severity of wildfires has increased during the past decades (Bodi, 2013). Certini (2013) assumed that cumulatively all of the vegetated land is burned in about 31 years annually affecting 330-430 Mha (over 3% of the Earth's surface) and wide range of land cover types worldwide including forests, peatlands, shrublands and grasslands. Whereas, the fire is identified as an important factor in soil formation, the

Associative properties of 137Cs in biofuel ashes

International Nuclear Information System (INIS)

Ravila, A.; Holm, E.

1999-01-01

The present study aims to reveal how radiocesium is associated to the ash particles derived from biofuel combustion. A sequential extraction procedure was carried out for the characterisation of radiocesium speciation in ash generated by different fuels and burner types. The ash types considered were fly ash and bottom ash collected from Swedish district heating plants using bark wood or peat as fuel. A fraction of the radiocesium in biofuel ash can easily become solubilised and mobilised by water and also, a significant fraction of the radionuclides can be bound to the ash particles in cation-exchangeable forms. Therefore, at using the ash derived from biofuels to recycle mineral nutrients for forestry or short rotation coppicing, radiocesium solubilised and leached from the ash by rains has a potential to rather quickly enter the rooting zone of forest vegetation or energy crops. On the other hand, radiocesium strongly bound to the ash will migrate slowly into the soil column with the successive accumulation of litter and in the process act to maintain the external dose rate at an elevated level for a long time. The results of the sequential extraction procedure and activity determination of the different extracted fractions implies that the bioavailable fraction of radiocesium in ash from bark, wood or peat is in the range between 20-85% of the total ash contents. Peat ash collected from a powder burner strongly retained a large fraction (70-90%) of its radiocesium content while the peat ash from a continuos fluidized bed type burner retained nearly 100% of the radiocesium in the bottom ash and only about 15% in the fly ash

Indirect effects of emerald ash borer-induced ash mortality and canopy gap formation on epigaeic beetles.

Science.gov (United States)

Gandhi, Kamal J K; Smith, Annemarie; Hartzler, Diane M; Herms, Daniel A

2014-06-01

Exotic herbivorous insects have drastically and irreversibly altered forest structure and composition of North American forests. For example, emerald ash borer (Agrilus planipennis Fairmaire) from Asia has caused wide-scale mortality of ash trees (Fraxinus spp.) in eastern United States and Canada. We studied the effects of forest changes resulting from emerald ash borer invasion on epigaeic or ground beetles (Coleoptera: Carabidae) along a gradient of ash dieback and gap sizes in southeastern Michigan. Ground beetles were sampled in hydric, mesic, and xeric habitats in which black (Fraxinus nigra Marshall), green (Fraxinus pennsylvanica Marshall), and white (Fraxinus americana L.) ash were the most common species, respectively. During 2006-2007, we trapped 2,545 adult ground beetles comprising 52 species. There was a negative correlation between percent ash tree mortality in 2006 and catches of all beetles. Catches of Agonum melanarium Dejean (in 2006) and Pterostichus mutus (Say) (in 2006-2007) were negatively correlated with tree mortality and gap size, respectively. However, catches of Pterostichus corvinus Dejean were positively correlated with gap size in 2006. As ash mortality and average gap size increased from 2006 to 2007, catches of all beetles as well as P. mutus and Pterostichus stygicus (Say) increased (1.3-3.9 times), while species diversity decreased, especially in mesic and xeric stands. Cluster analysis revealed that beetle assemblages in hydric and mesic stand diverged (25 and 40%, respectively) in their composition from 2006 to 2007, and that hydric stands had the most unique beetle assemblages. Overall, epigaeic beetle assemblages were altered in ash stands impacted by emerald ash borer; however, these impacts may dissipate as canopy gaps close.

[Importance of accurate assessment of capillary blood glucose level in diagnosis: misleading results in handlers of prickly pears (Opuntia ficus-indica)].

Science.gov (United States)

García Pantoja, José; Landróguez Salinas, Sergio; Barrero Luque, Susana; Pérez Pérez, José Antonio

2016-01-01

Hypoglycemia can cause symptoms of neuroglycopenia that can be easily confused with symptoms of greater clinical importance such as stroke. Appropriate differential diagnosis between these 2 processes will be essential for guiding the treatment approach. We report a case in which stroke was initially suspected because hypoglycemia was masked by the incorrect capillary blood glucose (CBG) measurement technique used in treating an itinerant vendor of prickly pears (Opuntia ficus-indica). We studied the effects of prickly pear handling on the CBG levels in 11 vendors before and after they handled the fruit. CBG levels were noticeably higher after the fruit was handled in all cases. Our observations reveal the need to measure both capillary and venous blood glucose levels to rule out hypoglycemia in patients with acute neurological symptoms.

Review of ecosystem level impacts of emerald ash borer on black ash wetlands: What does the future hold?

Science.gov (United States)

Randall K. Kolka; Anthony W. D' Amato; Joseph W. Wagenbrenner; Robert A. Slesak; Thomas G. Pypker; Melissa B. Youngquist; Alexis R. Grinde; Brian J. Palik

2018-01-01

The emerald ash borer (EAB) is rapidly spreading throughout eastern North America and devastating ecosystems where ash is a component tree. This rapid and sustained loss of ash trees has already resulted in ecological impacts on both terrestrial and aquatic ecosystems and is projected to be even more severe as EAB invades black ash-dominated wetlands of the western...

Variation in the Volatile Profiles of Black and Manchurian Ash in Relation to Emerald Ash Borer Oviposition Preferences.

Science.gov (United States)

Rigsby, Chad M; McCartney, Nathaniel B; Herms, Daniel A; Tumlinson, James H; Cipollini, Don

2017-08-01

Emerald ash borer (EAB; Agrilus planipennis) is a devastating pest of ash (Fraxinus spp.) in its invaded range in North America. Its coevolved Asian hosts are more resistant and less preferred for oviposition than susceptible North American species. We compared EAB oviposition preferences and bark and canopy volatile organic compound (VOC) emissions of resistant Manchurian ash and susceptible black ash, and examined relationships between VOC profiles and oviposition. In the field, black ash was highly preferred for oviposition while no eggs were laid on Manchurian ash, and we found clear differences in the VOC profiles of Manchurian and black ash. We detected 78 compounds emitted from these species, including 16 compounds that elicited EAB antennal activity in prior studies. Four compounds were unique to black and 11 to Manchurian ash. Emission rates of 14 canopy and 19 bark volatiles varied among the two species, including four previously reported as antennally active. Specifically, 7-epi-sesquithujene (bark) emissions were greater from black ash, while β-caryophyllene (canopy), linalool (bark), and α-cubebene (bark) were emitted at higher rates by Manchurian ash. No relationships were found between the emission rate of any single compound or group of compounds (e.g. monoterpenes) suggesting that preference may be based on complex profile combinations. This is the first study to directly compare VOCs of black and Manchurian ash as well as the first to examine bark- and canopy-specific VOCs. The unique bark and canopy VOC profiles of these two species implicates potentially important variation in VOCs between a closely related resistant and susceptible species that provides a foundation for future studies of host preferences of EAB.

Characteristic differences in essential oil composition of six Zanthoxylum bungeanum Maxim. (Rutaceae) cultivars and their biological significance.

Science.gov (United States)

Liu, Shu-Ming; Wang, Shi-Jun; Song, Si-Yao; Zou, Yong; Wang, Jun-Ru; Sun, Bing-Yin

Great variations have been found in composition and content of the essential oil of Zanthoxylum bungeanum Maxim. (Rutaceae), resulting from various factors such as harvest time, drying and extraction methods (Huang et al., 2006; Shao et al., 2013), solvent and herbal parts used (Zhang, 1996; Cao and Zhang, 2010; Wang et al., 2011). However, in terms of artificial introduction and cultivation, there is little research on the chemical composition of essential oil extracted from Z. bungeanum Maxim. cultivars, which have been introduced from different origins. In this study, the composition and content of essential oil from six cultivars (I-VI) have been investigated. They were introduced and cultivated for 11 years in the same cultivation conditions. Cultivars were as followings: Qin'an (I) cultivar originally introduced from Qin'an City in Gansu Province; Dahongpao A (II) from She County in Hebei Province; Dahongpao B (III) from Fuping County; Dahongpao C (IV) from Tongchuan City; Meifengjiao (V) from Feng County; and, Shizitou (VI) from Hancheng City, in Shaanxi Province, China. This research is expected to provide a theoretical basis for further introduction, cultivation, and commercial development of Z. bungeanum Maxim.

Optimizing Use of Girdled Ash Trees for Management of Low-Density Emerald Ash Borer (Coleoptera: Buprestidae) Populations.

Science.gov (United States)

Siegert, Nathan W; McCullough, Deborah G; Poland, Therese M; Heyd, Robert L

2017-06-01

Effective survey methods to detect and monitor recently established, low-density infestations of emerald ash borer, Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), remain a high priority because they provide land managers and property owners with time to implement tactics to slow emerald ash borer population growth and the progression of ash mortality. We evaluated options for using girdled ash (Fraxinus spp.) trees for emerald ash borer detection and management in a low-density infestation in a forested area with abundant green ash (F. pennsylvanica). Across replicated 4-ha plots, we compared detection efficiency of 4 versus 16 evenly distributed girdled ash trees and between clusters of 3 versus 12 girdled trees. We also examined within-tree larval distribution in 208 girdled and nongirdled trees and assessed adult emerald ash borer emergence from detection trees felled 11 mo after girdling and left on site. Overall, current-year larvae were present in 85-97% of girdled trees and 57-72% of nongirdled trees, and larval density was 2-5 times greater on girdled than nongirdled trees. Low-density emerald ash borer infestations were readily detected with four girdled trees per 4-ha, and 3-tree clusters were as effective as 12-tree clusters. Larval densities were greatest 0.5 ± 0.4 m below the base of the canopy in girdled trees and 1.3 ± 0.7 m above the canopy base in nongirdled trees. Relatively few adult emerald ash borer emerged from trees felled 11 mo after girdling and left on site through the following summer, suggesting removal or destruction of girdled ash trees may be unnecessary. This could potentially reduce survey costs, particularly in forested areas with poor accessibility. Published by Oxford University Press on behalf of Entomological Society of America 2017. This work is written by US Government employees and is in the public domain in the US.

Skin prick test reactivity to aeroallergens by filaggrin mutation status

DEFF Research Database (Denmark)

Hougaard, M G; Johansen, J D; Linneberg, A

2014-01-01

BACKGROUND: Studies have shown that filaggrin gene (FLG) mutations are positively associated with sensitization to aero allergens. We hypothesized that FLG mutations would also have an effect on the mean size of positive skin prick test (SPT) reactions as well as the number of positive reactions....... OBJECTIVE: To investigate the effect of FLG mutations on the mean size and the number of positive SPT reactions, as well as the association with positive specific IgE. METHODS: A random sample of 3335 adults from the general population in Denmark was genotyped for the R501X and 2282del4 mutations in the FLG...... mutations alone are insufficient to cause secondary sensitization to allergens. The positive association seen in patients must be explained by a combination of further barrier abnormality caused by dermatitis as well as increased allergen exposure....

Bio-cultural anchorage of the prickly pear cactus in Tlalnepantla (Morelos, Mexico

Directory of Open Access Journals (Sweden)

Torres-Salcido, Gerardo

2016-06-01

Full Text Available The prickly pear cactus is a source of food with strong bio-cultural anchorage in Mexico. This is due to at least three factors: 1 the nature and heritage of cacti; 2 cultural heritage; and 3 the socio-cultural relationships with historical and symbolic roots that have facilitated knowledge of how to cultivate it and how to use it. The aim of this article is to put factors of territorial anchorage and its historical transformation in context by examining the case of the municipality of Tlalnepantla in the state of Morelos, Mexico. This community has experienced accelerated change due to the exchange of traditional crops for the prickly pear cactus and the integration of farming, commercialization and agro-transformation. Our hypothesis is that the market, internal conflicts and a lack of socio-institutional coordination have put social organization into crisis, favoring the territorial spread of the prickly pear cactus and making the Local Agro-Food Systems (LAFS of Tlalnepantla less competitive. The conclusions highlight important economic and social advances whose roots lie in the strengthening and anchorage of the territory-product. However, circumstances both internal and external to the community persist, such as intra-community conflicts, the international market and cultural paradigm shifts that affect the producers and put consolidation of the LAFS at risk.El nopal es un alimento con un fuerte anclaje bio-cultural en México, propiciado por al menos tres factores: 1 la naturaleza y el patrimonio de cactáceas; 2 el patrimonio cultural; y, 3 las relaciones socio-culturales que han permitido un “saber hacer” y un “saber utilizar” con raíces históricas y simbólicas. El objetivo es situar los factores de anclaje territorial y su transformación histórica tomando como caso el municipio de Tlalnepantla, en el estado de Morelos, México. Esta comunidad ha experimentado un acelerado cambio por la reconversión de los cultivos

Volcanic ash dosage calculator: A proof-of-concept tool to support aviation stakeholders during ash events

Science.gov (United States)

Dacre, H.; Prata, A.; Shine, K. P.; Irvine, E.

2017-12-01

The volcanic ash clouds produced by Icelandic volcano Eyjafjallajökull in April/May 2010 resulted in `no fly zones' which paralysed European aircraft activity and cost the airline industry an estimated £1.1 billion. In response to the crisis, the Civil Aviation Authority (CAA), in collaboration with Rolls Royce, produced the `safe-to-fly' chart. As ash concentrations are the primary output of dispersion model forecasts, the chart was designed to illustrate how engine damage progresses as a function of ash concentration. Concentration thresholds were subsequently derived based on previous ash encounters. Research scientists and aircraft manufactures have since recognised the importance of volcanic ash dosages; the accumulated concentration over time. Dosages are an improvement to concentrations as they can be used to identify pernicious situations where ash concentrations are acceptably low but the exposure time is long enough to cause damage to aircraft engines. Here we present a proof-of-concept volcanic ash dosage calculator; an innovative, web-based research tool, developed in close collaboration with operators and regulators, which utilises interactive data visualisation to communicate the uncertainty inherent in dispersion model simulations and subsequent dosage calculations. To calculate dosages, we use NAME (Numerical Atmospheric-dispersion Modelling Environment) to simulate several Icelandic eruption scenarios, which result in tephra dispersal across the North Atlantic, UK and Europe. Ash encounters are simulated based on flight-optimal routes derived from aircraft routing software. Key outputs of the calculator include: the along-flight dosage, exposure time and peak concentration. The design of the tool allows users to explore the key areas of uncertainty in the dosage calculation and to visualise how this changes as the planned flight path is varied. We expect that this research will result in better informed decisions from key stakeholders during

Proceedings of symposium on ash in North America

Science.gov (United States)

Charles H. Michler; Matthew D., eds. Ginzel

2010-01-01

Includes 5 papers and 30 abstracts covering topics related to the biology and ecology of the ash species, ash utilization and management, emerald ash borer, and other threats to ash, and genetics and conservation of ash species. A paper titled "Population-level variation of Fraxinus americana L. is influenced by climate...

Factors affecting the survival of ash (Fraxinus spp.) trees infested by emerald ash borer (Agrilus planipennis)

Science.gov (United States)

Kathleen S. Knight; John P. Brown; Robert P. Long

2013-01-01

Emerald ash borer (Agrilus planipennis) (EAB), an Asian woodboring beetle accidentally introduced in North America, has killed millions of ash (Fraxinus spp.) trees and is spreading rapidly. This study examined the effects of tree- and site-level factors on the mortality of ash trees in stands infested by EAB in OH, USA. Our data...

Use of unwounded ash trees for the detection of emerald ash borer adults: EAB landing behavior

Science.gov (United States)

Jordan M. Marshall; Melissa J. Porter; Andrew J. Storer

2011-01-01

Incorporation of multiple trapping techniques and sites within a survey program is essential to adequately identify the range of emerald ash borer (EAB) (Agrilus planipennis Fairmaire) infestation. Within natural forests, EAB lands on stick band traps wrapped around girdled ash trees at a rate similar to that on unwounded ash trees. The objective of...

Effects of water availability on emerald ash borer larval performance and phloem phenolics of Manchurian and black ash.

Science.gov (United States)

Chakraborty, Sourav; Whitehill, Justin G A; Hill, Amy L; Opiyo, Stephen O; Cipollini, Don; Herms, Daniel A; Bonello, Pierluigi

2014-04-01

The invasive emerald ash borer (EAB) beetle is a significant threat to the survival of North American ash. In previous work, we identified putative biochemical and molecular markers of constitutive EAB resistance in Manchurian ash, an Asian species co-evolved with EAB. Here, we employed high-throughput high-performance liquid chromatography with photodiode array detection and mass spectrometry (HPLC-PDA-MS) to characterize the induced response of soluble phloem phenolics to EAB attack in resistant Manchurian and susceptible black ash under conditions of either normal or low water availability, and the effects of water availability on larval performance. Total larval mass per tree was lower in Manchurian than in black ash. Low water increased larval numbers and mean larval mass overall, but more so in Manchurian ash. Low water did not affect levels of phenolics in either host species, but six phenolics decreased in response to EAB. In both ashes, pinoresinol A was induced by EAB, especially in Manchurian ash. Pinoresinol A and pinoresinol B were negatively correlated with each other in both species. The higher accumulation of pinoresinol A in Manchurian ash after attack may help explain the resistance of this species to EAB, but none of the responses measured here could explain increased larval performance in trees subjected to low water availability. © 2013 John Wiley & Sons Ltd.

Review of Ecosystem Level Impacts of Emerald Ash Borer on Black Ash Wetlands: What Does the Future Hold?

Directory of Open Access Journals (Sweden)

Randall K. Kolka

2018-04-01

Full Text Available The emerald ash borer (EAB is rapidly spreading throughout eastern North America and devastating ecosystems where ash is a component tree. This rapid and sustained loss of ash trees has already resulted in ecological impacts on both terrestrial and aquatic ecosystems and is projected to be even more severe as EAB invades black ash-dominated wetlands of the western Great Lakes region. Using two companion studies that are simulating short- and long-term EAB infestations and what is known from the literature, we synthesize our current limited understanding and predict anticipated future impacts of EAB on black ash wetlands. A key response to the die-back of mature black ash will be higher water tables and the potential for flooding and resulting changes to both the vegetation and animal communities. Although seedling planting studies have shown some possible replacement species, little is known about how the removal of black ash from the canopy will affect non-ash species growth and regeneration. Because black ash litter is relatively high in nitrogen, it is expected that there will be important changes in nutrient and carbon cycling and subsequent rates of productivity and decomposition. Changes in hydrology and nutrient and carbon cycling will have cascading effects on the biological community which have been scarcely studied. Research to address these important gaps is currently underway and should lead to alternatives to mitigate the effects of EAB on black ash wetland forests and develop management options pre- and post-EAB invasion.

Topical non-peptide antagonists of sensory neurotransmitters substance P and CGRP do not modify patch test and prick test reactions

DEFF Research Database (Denmark)

Wallengren, Joanna; Edvinsson, Lars

2014-01-01

developed. Their effect on the skin barrier was measured in terms of transepidermal water loss (TEWL) while permeation was calculated using permeation coefficients. Patch tests in patients allergic to nickel and prick test reactions to histamine were used as models. None of the treatments increased TEWL......, suggesting there to be no impairment of the skin barrier. Permeation coefficients indicated moderate permeation. Histamine prick tests induced a flare with a mean area of 662 + 275 mm(2) and a weal with a mean volume of 49 + 11 mm(3). These reactions as well as histamine-induced pruritus were not affected...... significantly by any of the treatments. Treatment with aprepitant and its vehicle alone resulted in a potentiating of the infiltration of nickel reactions compared with test reactions obtained after no treatment (1147 + 423 mm(3) and 1427 + 566 mm(3) vs 683 +202 mm(3)) (p = 0.03). Telcagepant induced...

Softening behaviour of brown coal ashes. Influence of ash components and gas atmosphere

Energy Technology Data Exchange (ETDEWEB)

Hegermann, R; Huettinger, K J [Karlsruhe Univ. (T.H.) (Germany, F.R.). Inst. fuer Chemische Technik

1990-03-01

The softening behaviour of brown coal ashes during gasification is important for three reasons: (1) Formation of large agglomerates, (2) inactivation of catalytically active ash components, (3) encapsulation of parts of the coal. The softening behaviour of the ashes was studied with a high temperature dilatometer at ambient pressure in various atmospheres (air, CO{sub 2}, Ar/H{sub 2}O, Ar, H{sub 2}/H{sub 2}O, H{sub 2}) using a push-rod with a conical tip. The heating rate was 5 Kmin{sup -1}, the final temperature 1000deg C, the residence time 1 h. (orig.).

Drycon dry ash conveyor: dry bottom ash handling system with reduced operating costs and improved plant efficiency

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-07-01

The Drycon dry bottom ash extraction system is designed to remove bottom ash beneath the furnace, cooling it without any need of water. Fresh air in countercurrent flow to the ash is used for the ash cooling. Data presented show how savings of time and costs can be achieved with this system and how a boiler efficiency can be increased using this technology. Considerable advantages in the reliability of operation with new improvements of the design are described. 7 figs.

Characterization of ash pond ashes from 3rd thermal power plant by SEM/EDX and XRD methods

OpenAIRE

A Minjigmaa; Ts Zolzaya; E Bayanjargal; B Davaabal; J Temuujin

2014-01-01

  Coal combustion by products from ash pond of 3rdthermal power plant of Ulaanbaatar city have been collected in 2010 and 2013 years. The ash samples have been characterized by XRD, XRF and SEM-EDX methods in order to evaluate their chemical and mineralogical composition changes with disposed times. The mineralogical composition of ash varies with time though the chemical composition of the ashes were close each other. Possibly, inefficient operating condition of the TPS shows influence on th...

Project ash cultch: A report on optimal oyster cultch based on a prepared fly ash substratum

International Nuclear Information System (INIS)

Price, K.S.; Hansen, K.M.; Schlekat, C.E.

1991-01-01

Based on a three year study involving setting, growth, mortality, oyster condition, and metals accumulation, the evidence is extensive and convincing that stabilized coal ash is an acceptable oyster growing cultch (substratum). Oyster larvae are attracted to set on coal ash cultch at commercial fishery densities, tend to grow as well as on natural substrata (oyster shell), and are moderately more exposed to predators on the puck shaped ash materials as produced for this study. Oysters grown for one to two years on coal ash do not accumulate heavy metals and generally are in good health as measured by several biological condition indexes

Effects of Wood Ash on Soil Fungi

DEFF Research Database (Denmark)

Cruz Paredes, Carla

), copper (Cu) and nickel (Ni), is a major environmental concern. This work is part of the project ASHBACK (www.ashback.dk) which addresses the potentials and possible problems in re-distributing wood ash to the forest. The aim of this thesis was to determine the effects of biomass ash application...... in a Norway spruce forest where different amounts of wood ash were spread on the soil to study the effects on ectomycorrhizal (ECM) fungi, bioaccumulation of metals in sporocarps, and microbial communities. Laboratory microcosm experiments were run in parallel to the field studies, to compare the effects...... of wood ash with factorial additions of lime and Cd to disentangle the pH and Cd effects of wood ash amendments using community trait distributions. Barley yield, P content, and Cd content were not affected by biomass ashes. Some arbuscular mycorrhizal (AM) fungal species were reduced when biomass ashes...

Life cycle adaption of biofuel ashes. Evaluation of new techniques for pelletizing of biofuel ashes, especially regarding operational properties and environmental effects in the forest after ash recycling. Stage 1

International Nuclear Information System (INIS)

Loevgren, Linnea; Lundmark, Jan-Erik; Jansson, Charlotta

2000-11-01

The aim of the project 'Adaptation of Wood Ashes to Recycling' is to evaluate a new technique - roll pelleting - for making wood ash suitable for reuse as a fertiliser for woodland. The project is being carried out at the forest product companies AssiDomaen and Stora Enso. The main financier is the Swedish National Energy Administration. Other financiers are AssiDomaen, Stora Enso, The Thermal Engineering Research Institute and The Forestry Research Institute of Sweden. The project has involved the construction of a full-scale roll pelleter in a mobile container and its trial operation at two Swedish pulp and paper mills. The leaching properties of the ash products were studied with a laboratory method. In addition, the effects of ash fertilisation with these products are being studied in a four-year field trial. Effects on soil pH, nutrient supply, soil water chemistry and ground vegetation are being evaluated by The Forestry Research Institute of Sweden and will be reported separately in the year 2003. In a laboratory prestudy, the leaching properties of pellets from twelve different ash products made in a laboratory prototype machine were evaluated. The ash products were made from residues from the AssiDomaen Froevi mill and the Stora Enso Fors mill. Fly ash from Froevi was used alone and mixed with green liquor sludge and lime sludge respectively. Fly ash from Fors was also used alone and mixed with coating colour. The laboratory method used for the evaluation of leaching properties is the method developed by IVL The Swedish Environmental Research Institute Ltd. The results show that the progress of the leaching of roll pelleted ash is significantly slower than for the corresponding crushed product and a reference lime product. The speed of leaching, measured as acid neutralisation capacity, ANC, was significantly lower for the roll pelleted ash compared to self-hardened and crushed ash products. Because of the high content of calcium, lime has on the whole, a

Ash fusion temperatures and their association with the transformations of coal ash particles to slag

Energy Technology Data Exchange (ETDEWEB)

Gupta, S.K.; Wall, T.F.; Gupta, R.P. [Cooperative Research Centre for Black Coal Utilisation, Newcastle, NSW (Australia); Creelman, R.A. [Creelman (R.A.) and Associates, Sydney, NSW (Australia)

1997-04-01

Ash deposition on furnace walls in PF (pulverized fuel) furnaces is called slagging when it occurs in the high temperature areas of furnaces directly exposed to flame radiation and fouling in other regions such as tubes in the convection section of the boiler. There are well documented shortcomings of certain approaches relating to their uncertainties as predictive tools for plant performance such as poor repeatability and re-producibility of ash fusion measurements. The nature of physical and chemical changes occurring during melting of coal ash has been investigated in the current study to provide an alternative procedure to the ash fusion test. Shrinkage measurements are frequently used in metallurgy and ceramic science to study the physical properties of materials at high temperatures. The output of this experiment provides three to four `peaks` (maximum rate of shrinkage with temperature) of different intensity and at different temperatures which are related to melting characteristics of the sample. It was concluded that shrinkage extents exceeding 50 percent indicated that the effect of the ash particle size is of secondary importance compared to ash chemistry in determining shrinkage levels, with fine particles giving rapid shrinkage events 10 degrees C lower in temperature. (author). 7 figs., refs.

Extracts of Canadian first nations medicinal plants, used as natural products, inhibit neisseria gonorrhoeae isolates with different antibiotic resistance profiles.

Science.gov (United States)

Cybulska, Paulina; Thakur, Sidharath D; Foster, Brian C; Scott, Ian M; Leduc, Renée I; Arnason, John T; Dillon, Jo-Anne R

2011-07-01

Neisseria gonorrhoeae (Ng) has developed resistance to most antimicrobial agents and the antibiotics recommended for therapy are restricted, for the most part, to third generation cephalosporins. In order to investigate new potential sources of antimicrobial agents, the antibacterial properties of 14 Canadian plants used in traditional First Nations' medicine were tested against Ng isolates having differing antimicrobial susceptibility profiles. Ethanolic extracts of 14 Canadian botanicals, analyzed by high-performance liquid chromatography, were tested for their antimicrobial activity (disc diffusion and/or agar dilution assays) against susceptible Ng reference strains and a panel of 28 Ng isolates with various antimicrobial resistance profiles. Extracts of Arctostaphylos uva ursi (kinnikinnick or bearberry), Hydrastis canadensis (goldenseal), Prunus serotina (black cherry), and Rhodiola rosea (roseroot) inhibited the growth of all Ng isolates with minimum inhibitory concentrations of 32 μg/mL, 4 to 32 μg/mL, 16 to >32 μg/mL, and 32 to 64 μg/mL, respectively. Extracts of Acorus americanus (sweet flag), Berberis vulgaris (barberry), Cimicifuga racemosa (black cohosh), Equisetum arvense (field horsetail), Gaultheria procumbens (wintergreen), Ledum groenlandicum (Labrador tea), Ledum palustre (marsh Labrador tea), Oenothera biennis (common evening primrose), Sambucus nigra (elderberry), and Zanthoxylum americanum (prickly ash) had weak or no antimicrobial activity against the Ng isolates with minimum inhibitory concentrations ≥256 μg/mL. The phytochemical berberine from H. canadensis inhibited the growth of all Ng isolates. The phytochemicals, salidroside and rosavin, present in R. rosea, also showed inhibitory activity against Ng strains. Canadian botanicals represent a potential source of novel compounds which inhibit Ng, including isolates resistant to antibiotics.

Lifting properties of the alkamide fraction from the fruit husks of Zanthoxylum bungeanum.

Science.gov (United States)

Artaria, C; Maramaldi, G; Bonfigli, A; Rigano, L; Appendino, G

2011-08-01

The fruits of various Zanthoxylum species are used as a spice in the Chinese and Japanese cuisine because of their delicate flavour and tingling properties. The lipophilic hydroxyalkamides hydroxy α- and β-sanshools (1a,b) have been identified as the tingling principles of these plants, and previous studies have validated a sanshool-rich lipophilic extract from the fruit husks of Z. bungeanum Maxim. (Zanthalene ® ) as an anti-itching cosmetic ingredient. Because tingling is a sort of 'paralytic pungency', and Zanthalene ® potently inhibits synaptic transmission, we have investigated its capacity to relax subcutaneous muscles and act as a topical lifting agent for wrinkles. An anti-wrinkles extract rich in spilanthol (2), a lipophilic alkamide having sensory properties similar to those of Zanthalene ® , was used as a reference. Short-term (lifting effect) and long-term (anti-wrinkle) improvements of skin roughness parameters were evaluated by both objectives' and subjectives' measurements. An immediate 'lifting' effect was observed with the sanshool-rich lipophilic extract, at dosages at which the reference alkamide extract was inactive in the objective assays. Limited desensitization after repeated application and good overall tolerability were observed, although a modest long-term anti-wrinkle effect was shown by both products. Taken together, these observations validate the use of sanshool-rich lipophilic extracts as an efficacious, immediate-action lifting agent, and exemplify the relevance of sensory observations to foster the development of innovative cosmetic ingredients. © 2011 The Authors. ICS © 2011 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

Publication sites productive uses of combustion ash

Science.gov (United States)

Publication Sites Productive Uses of Combustion Ash For more information contact: e:mail: Public waste combustion ash in landfills. The new technology brief describes recent studies where ash was used

Effects of chemical composition of fly ash on efficiency of metal separation in ash-melting of municipal solid waste

Energy Technology Data Exchange (ETDEWEB)

Okada, Takashi, E-mail: t-okada@u-fukui.ac.jp [Laboratory of Solid Waste Disposal Engineering, Graduate School of Engineering, Hokkaido University, Kita 13 Nishi 8, Kita-ku, Sapporo 060-8628 (Japan); Tomikawa, Hiroki [Laboratory of Solid Waste Disposal Engineering, Graduate School of Engineering, Hokkaido University, Kita 13 Nishi 8, Kita-ku, Sapporo 060-8628 (Japan)

2013-03-15

Highlights: ► Separation of Pb and Zn from Fe and Cu in ash-melting of municipal solid waste. ► Molar ratio of Cl to Na and K in fly ash affected the metal-separation efficiency. ► The low molar ratio and a non-oxidative atmosphere were better for the separation. - Abstract: In the process of metal separation by ash-melting, Fe and Cu in the incineration residue remain in the melting furnace as molten metal, whereas Pb and Zn in the residue are volatilized. This study investigated the effects of the chemical composition of incineration fly ash on the metal-separation efficiency of the ash-melting process. Incineration fly ash with different chemical compositions was melted with bottom ash in a lab-scale reactor, and the efficiency with which Pb and Zn were volatilized preventing the volatilization of Fe and Cu was evaluated. In addition, the behavior of these metals was simulated by thermodynamic equilibrium calculations. Depending on the exhaust gas treatment system used in the incinerator, the relationships among Na, K, and Cl concentrations in the incineration fly ash differed, which affected the efficiency of the metal separation. The amounts of Fe and Cu volatilized decreased by the decrease in the molar ratio of Cl to Na and K in the ash, promoting metal separation. The thermodynamic simulation predicted that the chlorination volatilization of Fe and Cu was prevented by the decrease in the molar ratio, as mentioned before. By melting incineration fly ash with the low molar ratio in a non-oxidative atmosphere, most of the Pb and Zn in the ash were volatilized leaving behind Fe and Cu.

Gas generation in incinerator ash; Gasbildning i aska

Energy Technology Data Exchange (ETDEWEB)

Arm, Maria; Lindeberg, Johanna; Rodin, Aasa; Oehrstroem, Anna; Backman, Rainer; Oehman, Marcus; Bostroem, Dan

2006-02-15

In recent years, explosions have occurred in certain phases of ash handling in Sweden. Investigations have revealed that hydrogen may have been present in all cases. The hydrogen is believed to be generated by chemical reactions of aluminium and other metals within the ash in the presence of water. The purpose with this study is to increase the knowledge of gas generation of incinerator ash. Thereby, guides for appropriate ash management can be introduced and the risk for further explosions prevented. The study has comprised analyses of the ash properties, such as chemical and physical composition and the pH, of ash from 14 incineration plants (mostly waste incineration plants). Different fractions of ash materials representing different parts of the process in each plant have been analysed. Furthermore, the fuel and the technical differences between the plants have been analysed. A tool for measuring the gas generation in the laboratory has been developed and the gas generation of the different ash materials at natural and increased pH was measured. Gas analyses and thermodynamic calculations have also been performed. The results showed that: bottom ash from fluidised bed boilers generated small amounts of gas at increased pH, much smaller amounts than the idle pass, cyclone and filter ash did, bottom ash from grate fired boilers generated more gas at increased pH than their cyclone ash and filter ash, with exception of the Linkoeping plant, all bio waste incineration plants generated ash with low gas generation potential, all fly ash materials with a gas generation potential of more than 10 l/kg originated from municipal waste incineration plants, filter ash that had been stored in oxygen rich environment generated significant less gas than fresh filter ash of the same origin, hardly any other gases were generated apart from hydrogen (very small amounts of acetone, furane, benzene and most likely methane were detected in some of the ash materials), there were no

Utilization of Hospital Waste Ash in Concrete

Directory of Open Access Journals (Sweden)

Shazim Ali Memon

2013-01-01

Full Text Available Hospital waste management is a huge problem in Pakistan. The annual production of medical waste produced from health care facilities, in Pakistan, is around 250,000 tons. This research paper is intended to evaluate the feasibility of using of hospital waste ash obtained from Pakistan Institute of Medical Sciences, Rawalpindi, Pakistan, as partial replacement of cement. The main variable in this research is the amount of hospital waste ash (2, 4, 6 and 8% by weight of cement while the amount of cementitious material, water to cementitious material ratio, fine and coarse aggregate content were kept constant. Test results substantiate that hospital waste ash can be used in concrete. XRD (X-Ray Diffraction of hospital waste ash showed that it is rich in calcite while scanning electron micrographs indicated that the particles of hospital waste ash have highly irregular shape. The slump value, density of fresh concrete and water absorption decreased with the increase in the quantity of hospital waste ash in the mix. At 3 days of testing, the compressive strength of mixes with hospital waste ash was higher than the control mix while at 7 and 28 days the CM (Control Mix showed higher strength than the hospital waste ash mixes except the mix containing 2% hospital waste ash by weight of cement.

Utilization of hospital waste ash in concrete

International Nuclear Information System (INIS)

Memon, S.; Sheikh, M.

2013-01-01

Hospital waste management is a huge problem in Pakistan. The annual production of medical waste produced from health care facilities, in Pakistan, is around 250,000 tons. This research paper is intended to evaluate the feasibility of using of hospital waste ash obtained from Pakistan Institute of Medical Sciences, Rawalpindi, Pakistan, as partial replacement of cement. The main variable in this research is the amount of hospital waste ash (2, 4, 6 and 8% by weight of cement) while the amount of cementitious material, water to cementitious material ratio, fine and coarse aggregate content were kept constant. Test results substantiate that hospital waste ash can be used in concrete. XRD (X-Ray Diffraction) of hospital waste ash showed that it is rich in calcite while scanning electron micrographs indicated that the particles of hospital waste ash have highly irregular shape. The slump value, density of fresh concrete and water absorption decreased with the increase in the quantity of hospital waste ash in the mix. At 3 days of testing, the compressive strength of mixes with hospital waste ash was higher than the control mix while at 7 and 28 days the CM (Control Mix) showed higher strength than the hospital waste ash mixes except the mix containing 2% hospital waste ash by weight of cement. (author)

The UZPI ash content monitoring device

Energy Technology Data Exchange (ETDEWEB)

Novikov, E.P.; Bezverkhii, E.A.; Mozhaev, L.G.

1987-07-01

This paper describes the results of industrial trials (in coal preparation plants) to establish the accuracy of the UZPI device which determines coal ash content using X-ray detection. It is designed to monitor ash content in the 4-40% range in coal with a grain size of 0-100 mm and a coal layer thickness of 50-150 mm (depending on the ash content and grain size). The ash frequently contains oxides, and although variations in magnesium, aluminium, silicon and sulfur oxides have virtually no effect on accuracy of the UZPI, changes in the levels of calcium oxides and particularly iron oxides have a considerable influence on measurement accuracy (caused by changes in their gamma ray scattering cross section values and atomic numbers). The overall sensitivity to ash content in coal varies from 1.6 to 2.4% abs./% while that to iron oxides in ash is 0.4% abs./%. Concludes that this device is suitable for use in coal preparation plants on thin layers of coal, but its efficiency is affected by external influences, e.g. fluctuations in conveyor loading.

Quality characteristics of Greek fly ashes and potential uses

Energy Technology Data Exchange (ETDEWEB)

Skodras, G.; Grammelis, P.; Kakaras, E. [Institute for Solid Fuels Technology and Applications, Ptolemais (Greece); Karangelos, D.; Anagnostakis, M.; Hinis, E. [Nuclear Engineering Section, Mechanical Engineering Department, National Technical University of Athens, Athens (Greece)

2007-01-15

The main characteristics of fly ash from Greek coal-fired boilers are presented in this paper in relation to its exploitation potential. Both fuel and fly ash samples were collected and analyzed according to the ASTM Standards. Apart from the typical analyses (proximate, ultimate, ash analysis and calorific value), an ICP-AES spectrometer was used for the analysis of heavy metals in the ash. Experimental measurements in order to determine the radioactivity content of raw fuel and the fly ash were carried out as well. A representative fly ash sample from Ptolemais power plant was evaluated and tested as filler in Self-Compacting Concrete (SCC). Ashes from the Greek brown coal are classified in type C, most of the fly ash being produced in Ptolemais of Northern Greece, while the rest in Megalopolis. Ptolemais fly ash is rich in calcium compounds, while Megalopolis fly ash contains more pyrite. Increased heavy metal concentrations are observed in the fly ash samples of Greek coal. Greek fly ash appears to have not only pozzolanic but also hydraulic behaviour. Furthermore, Greek fly ash, depending on its origin, may have relatively high natural radioactivity content, reaching in the case of Megalopolis fly ash 1 kBq kg{sup -1} of {sup 226}Ra. The laboratory results showed that fly ashes can be a competitive substitute to conventional limestone filler material in SCC. Fly ash is mostly used in Greece in cement industry replacing cement clinker and aiming to the production of special types of Portland cements. However, a more aggressive utilisation strategy should be developed, since low quantities of the total produced fly ash are currently further utilised. (author)

Breeding strategies for the development of emerald ash borer - resistant North American ash

Science.gov (United States)

Jennifer L. Koch; David W. Carey; Kathleen S. Knight; Therese Poland; Daniel A. Herms; Mary E. Mason

2012-01-01

The emerald ash borer (Agrilus plannipennis; EAB) is a phloem-feeding beetle that is endemic to Asia. It was discovered in North America in 2002, found almost simultaneously near Detroit, Michigan and Windsor, Ontario, Canada. Adult beetles feed on ash (Fraxinus spp.) foliage, but larval feeding on phloem, cambium, and...

Outlook for ash in your forest: results of emerald ash borer research and implications for management

Science.gov (United States)

Kathleen S. Knight

2014-01-01

Since its accidental introduction near Detroit, Michigan, in the mid-1990s, emerald ash borer (EAB) has rapidly spread through much of the U.S. and adjacent Canada, leaving millions of dead ash trees in Midwestern states (4,11). Unfortunately, EAB attacks trees as small as an inch in stem diameter and it attacks all five ash species native to the region - white, green...

Analysis list: ash-2 [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available ash-2 Adult,Embryo + ce10 http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/target/as...h-2.1.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/target/ash-2.5.tsv http://dbarchive.biosciencedbc....jp/kyushu-u/ce10/target/ash-2.10.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/colo/ash-2.Adult.tsv,http://dbarchive.bioscience...dbc.jp/kyushu-u/ce10/colo/ash-2.Embryo.tsv http://dbarchive.bioscience...dbc.jp/kyushu-u/ce10/colo/Adult.gml,http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/colo/Embryo.gml ...

Composites Based on Fly Ash and Clay

International Nuclear Information System (INIS)

Fidancevska, E.; Jovanov, V.; Angusheva, B.; Srebrenkoska, V.

2014-01-01

Fly ash is a waste generated from the coal combustion during the production of electricity in the thermal power plants. It presents industrial by-product containing Technologically Enhanced Natural Occurring Radioactive Materials (TENORM) with the great potential for valorisation. Fly ash is successfully utilized in cement and concrete industry, also in ceramics industry as component for manufacturing bricks and tiles, and recently there are many investigations for production of glass-ceramics from fly ash. Although the utilization of fly ash in construction and civil engineering is dominant, the development of new alternative application for its further exploitation into new products is needed. This work presents the possibility for fly ash utilization for fabricating dense composites based on clay and fly ash with the potential to be used in construction industry

Physiological responses of emerald ash borer larvae to feeding on different ash species reveal putative resistance mechanisms and insect counter-adaptations.

Science.gov (United States)

Rigsby, C M; Showalter, D N; Herms, D A; Koch, J L; Bonello, P; Cipollini, D

2015-07-01

Emerald ash borer, Agrilus planipennis Fairmaire, an Asian wood-boring beetle, has devastated ash (Fraxinus spp.) trees in North American forests and landscapes since its discovery there in 2002. In this study, we collected living larvae from EAB-resistant Manchurian ash (Fraxinus mandschurica), and susceptible white (Fraxinus americana) and green (Fraxinus pennsylvanica) ash hosts, and quantified the activity and production of selected detoxification, digestive, and antioxidant enzymes. We hypothesized that differences in larval physiology could be used to infer resistance mechanisms of ash. We found no differences in cytochrome P450, glutathione-S-transferase, carboxylesterase, sulfotransferase, and tryptic BApNAase activities between larvae feeding on different hosts. Despite this, Manchurian ash-fed larvae produced a single isozyme of low electrophoretic mobility that was not produced in white or green ash-fed larvae. Additionally, larvae feeding on white and green ash produced two serine protease isozymes of high electrophoretic mobility that were not observed in Manchurian ash-fed larvae. We also found lower activity of β-glucosidase and higher activities of monoamine oxidase, ortho-quinone reductase, catalase, superoxide dismutase, and glutathione reductase in Manchurian ash-fed larvae compared to larvae that had fed on susceptible ash. A single isozyme was detected for both catalase and superoxide dismutase in all larval groups. The activities of the quinone-protective and antioxidant enzymes are consistent with the resistance phenotype of the host species, with the highest activities measured in larvae feeding on resistant Manchurian ash. We conclude that larvae feeding on Manchurian ash could be under quinone and oxidative stress, suggesting these may be potential mechanisms of resistance of Manchurian ash to EAB larvae, and that quinone-protective and antioxidant enzymes are important counter-adaptations of larvae for dealing with these resistance

Ash Stabilization Campaign Blend Plan

International Nuclear Information System (INIS)

Winstead, M.L.

1995-01-01

This Stabilization Blend Plan documents the material to be processed and the processing order for the FY95 Ash Stabilization Campaign. The primary mission of this process is to reduce the inventory of unstable plutonium bearing ash. The source of the ash is from Rocky Flats and the 232-Z incinerator at the Plutonium Finishing Plant (PFP). The ash is currently being stored in Room 235B and Vault 174 in building 234-5Z. The sludge is to be thermally stabilized in a glovebox in room 230A of the 234-5Z building and material handling for the process will be done in room 230B of the same building. The campaign is scheduled for approximately 12--16 weeks. A total of roughly 4 kg of Pu will be processed

Adhesion Strength of Biomass Ash Deposits

DEFF Research Database (Denmark)

Laxminarayan, Yashasvi; Jensen, Peter Arendt; Wu, Hao

2016-01-01

. Therefore, timely removal of ash deposits is essential for optimal boiler operation. In order to improve the qualitative and quantitative understanding of deposit shedding in boilers, this study investigates the shear adhesion strength of biomass ash deposits on superheater tubes. Artificial biomass ash...... deposits were prepared on superheater tubes and sintered in an oven at temperatures up to 1000 °C. Subsequently, the deposits were sheared off by an electrically controlled arm, and the corresponding adhesion strength was measured. The results reveal the effect of temperature, ash/deposit composition......, sintering duration, and steel type on the adhesion strength....

Failure to phytosanitize ash firewood infested with emerald ash borer in a small dry kiln using ISPM-15 standards.

Science.gov (United States)

Goebel, P Charles; Bumgardner, Matthew S; Herms, Daniel A; Sabula, Andrew

2010-06-01

Although current USDA-APHIS standards suggest that a core temperature of 71.1 degrees C (160 degrees F) for 75 min is needed to adequately sanitize emerald ash borer, Agrilus planipennis Fairmaire-infested firewood, it is unclear whether more moderate (and economical) treatment regimes will adequately eradicate emerald ash borer larvae and prepupae from ash firewood. We constructed a small dry kiln in an effort to emulate the type of technology a small- to medium-sized firewood producer might use to examine whether treatments with lower temperature and time regimes successfully eliminate emerald ash borer from both spilt and roundwood firewood. Using white ash (Fraxinus americana L.) firewood collected from a stand with a heavy infestation of emerald ash borer in Delaware, OH, we treated the firewood using the following temperature and time regime: 46 degrees C (114.8 degrees F) for 30 min, 46 degrees C (114.8 degrees F) for 60 min, 56 degrees C (132.8 degrees F) for 30 min, and 56 degrees C (132.8 degrees F) for 60 min. Temperatures were recorded for the outer 2.54-cm (1-in.) of firewood. After treatment, all firewood was placed under mesh netting and emerald ash borer were allowed to develop and emerge under natural conditions. No treatments seemed to be successful at eliminating emerald ash borer larvae and perpupae as all treatments (including two nontreated controls) experienced some emerald ash borer emergence. However, the 56 degrees C (132.8 degrees F) treatments did result in considerably less emerald ash borer emergence than the 46 degrees C (114.8 degrees F) treatments. Further investigation is needed to determine whether longer exposure to the higher temperature (56 degrees C) will successfully sanitize emerald ash borer-infested firewood.

Methods to Improve Survival and Growth of Planted Alternative Species Seedlings in Black Ash Ecosystems Threatened by Emerald Ash Borer

Science.gov (United States)

Nicholas Bolton; Joseph Shannon; Joshua Davis; Matthew Grinsven; Nam Noh; Shon Schooler; Randall Kolka; Thomas Pypker; Joseph Wagenbrenner

2018-01-01

Emerald ash borer (EAB) continues to spread across North America, infesting native ash trees and changing the forested landscape. Black ash wetland forests are severely affected by EAB. As black ash wetland forests provide integral ecosystem services, alternative approaches to maintain forest cover on the landscape are needed. We implemented simulated EAB infestations...

Exploitation of Leuconostoc mesenteroides strains to improve shelf life, rheological, sensory and functional features of prickly pear (Opuntia ficus-indica L.) fruit puree.

Science.gov (United States)

Di Cagno, Raffaella; Filannino, Pasquale; Vincentini, Olimpia; Lanera, Alessia; Cavoski, Ivana; Gobbetti, Marco

2016-10-01

Strains of Leuconostoc mesenteroides were identified from raw prickly pear (Opuntia ficus-indica L.). Five autochthonous strains were selected based on the kinetics of growth and acidification on prickly pear fruit juice, and the capacity to synthesize exo-polysaccharides. All selected Leuc. mesenteroides strains showed an in vitro mucilage-degrading capability. A protocol for processing and storage of fermented prickly pear fruit puree (FP) was set up. Unstarted FP and chemically acidified FP were used as the controls. Starters grew and remained viable at elevated cell numbers during 21 days of storage at 4 °C. Contaminating Enterobacteriaceae and yeasts were found only in the controls. Viscosity and serum separation distinguished started FP compared to the controls. Colour parameters, browning index, sensory attributes, antimicrobial activity, vitamin C and betalains levels were positively affected by lactic acid fermentation. Increase of free radical scavenging activity in ethyl acetate soluble extract suggested an effect of selected strains on phenolic profiles. Started FP markedly inhibited the inflammatory status of Caco-2/TC7 cells, and also contributed to maintaining the integrity of tight junctions. Started FP scavenged the reactive oxygen species generated by H2O2 on Caco-2 cells. All selected strain variously affected the immunomodulatory activity towards anti- and pro-inflammatory cytokines. Copyright © 2016 Elsevier Ltd. All rights reserved.

Wildland fire ash: future research directions

Science.gov (United States)

Bodí, Merche B.; Martins, Deborah A.; Cerdà, Artemi; Balfour, Victoria N.; Santin, Cristina; Doerr, Stefan H.; Pereira, Paulo; Mataix-Solera, Jorge

2014-05-01

Ash is a key component of the forest fires affected land (Cerdà, 1998; Bodí et al., 2011; Pereira et al., 2013a). Ash controls the hydrological processes and determines the water repellency (Dlapa et al., 2012) and the infiltration rates (Cerdà and Doerr, 2008;). Moreover, ash is the key factor on runoff initiation and then on the soil erosion. Little is known about the impact of ash in different ecosystems, but during the last decade a substantial increase in the papers that show the role of ash in the Earth and Soil System were published (Bodí et al., 2012; Pereira et al., 2013b).. Ash is being found as the key component of the post-fire pedological, geomorphological and hydrological response after forest fires (Fernández et al., 2012; Martín et al., 2012; Bodí et al., 2013; Guénon et al., 2013; Pereira et al., 2013c). A recent State-of-the-Art review about wildland fire ash (Bodí et al., 2014) compiles the knowledge regarding the production, composition and eco-hydro-geomorphic effects of wildland fire ash. In the present paper we indicate the knowledge gaps detected and suggest topics that need more research effort concerning: i) data collection and analysis techniques: a) To develop standardized sampling techniques that allow cross comparison among sites and avoid inclusion of the underlying soil unless the burned surface soil forms part of the ash layer, b) To develop standardized methods to define and characterize ash, including its color, physical properties such as particle size distribution or density, proportion of pyrogenic C, chemical and biological reactivity and persistence in the environment, c) To validate, calibrate and test measurements collected through remote sensing with on-the-ground measurements. ii) ash production, deposition redistribution and fate: d) To untangle the significance of the effects of maximum temperature reached during combustion versus the duration of heating, e) To understand the production of ash by measuring its

Characterization of ashes from biofuels

Energy Technology Data Exchange (ETDEWEB)

Frandsen, F.J.; Hansen, L.A. [Technical Univ. of Denmark. Dept. of Chemical Engineering (Denmark); Soerensen, H.S. [Geological Survey of Denmark and Greenland (Denmark); Hjuler, K. [dk-TEKNIK. Energy and Environment (Denmark)

1998-02-01

One motivation for initiating the present project was that the international standard method of estimating the deposit propensity of solid fuels, of which a number of variants exist (e.g. ISO, ASTM, SD, DIN), has shown to be unsuitable for biomass ashes. This goal was addressed by the development of two new methods for the detection of ash fusibility behaviour based on Simultaneous Thermal Analysis (STA) and High Temperature Light Microscopy (HTLM), respectively. The methods were developed specifically for ashes from biofuels, but are suitable for coal ashes as well. They have been tested using simple salt mixtures, geological standards and samples from straw CHP and coal-straw PF combustion plants. All samples were run in a nitrogen atmosphere at a heating rate of 10 deg. C/min. In comparison with the standard method, the new methods are objective and have superior repeatability and sensitivity. Furthermore, the two methods enable the melting behavior to be characterized by a continuous measurement of melt fraction versus temperature. Due to this two-dimensional resolution of the results, the STA and HTLM methods provide more information than the standard method. The study of bottom ash and fly ash as well as deposit samples from straw test firings at the Haslev and Slagelse Combined Heat and Power plants resulted in a better understanding of mineral behaviour during straw grate firing. In these tests a number of straws were fired which had been carefully selected for having different qualities with respect to sort and potassium and chlorine contents. By studying bottom ashes from Slagelse it was found that the melting behaviour correlated with the deposition rate on a probe situated at the outlet part of the combustion zone. (EG)

Crowdsourcing genomic analyses of ash and ash dieback – power to the people

Directory of Open Access Journals (Sweden)

MacLean Dan

2013-02-01

Full Text Available Abstract Ash dieback is a devastating fungal disease of ash trees that has swept across Europe and recently reached the UK. This emergent pathogen has received little study in the past and its effect threatens to overwhelm the ash population. In response to this we have produced some initial genomics datasets and taken the unusual step of releasing them to the scientific community for analysis without first performing our own. In this manner we hope to ‘crowdsource’ analyses and bring the expertise of the community to bear on this problem as quickly as possible. Our data has been released through our website at oadb.tsl.ac.uk and a public GitHub repository.

Leaching of saltstones containing fly ash

International Nuclear Information System (INIS)

Barnes, M.W.; Roy, D.M.; Langton, C.A.

1985-01-01

Two types of fly ash were incorporated in saltstones designed for potential encapsulation of Savannah River Plant low level defense waste. These fly ashes have some cementitious properties while at the same time their presence in substitution for cement slows early hydration. Class C fly ash has a high calcium content and is considered cementitious; Class F fly ash has a low calcium content and is not classified as cementitious. Leach tests were performed and physical properties were measured for saltstones containing each class, to see the differences in the effect of the fly ashes. The four waste ions nitrate, nitrite, sodium and sulfate were shown to leach by diffusion. Effective diffusivities were determined for these ions. Data for nitrate, the most important species from the environmental point of view, are shown in Table A. Saltstones made with Class C fly ash have substantially lower leach rates than those made with Class F fly ash. The leach rates, and therefore the square roots of the effective diffusivities, have been found to be proportional to the pore surface area per unit volume (or the ratio of pore volume to pore radius), to the fraction of waste containing solution, and to the inverse of the fraction of calcium in the saltstone. Rates and diffusivities are not proportional to the water to cement ratio, because this number depends on whether the fly ash is counted as cementitious, as in Class C cement, or not cementitious, as in Class F cement. In fact the relatively small amount of calcium in Class F cement contributes to the cementitious properties overall, though not so much as Class C cement. 4 refs., 2 figs., 6 tabs

Characterisation of wood combustion ashes

DEFF Research Database (Denmark)

Maresca, Alberto

The combustion of wood chips and wood pellets for the production of renewable energy in Denmark increased from 5.7 PJ to 16 PJ during the period 2000-2015, and further increases are expected to occur within the coming years. In 2012, about 22,300 tonnes of wood ashes were generated in Denmark....... Currently, these ashes are mainly landfilled, despite Danish legislation allowing their application onto forest and agricultural soils for fertilising and/or liming purposes. During this PhD work, 16 wood ash samples generated at ten different Danish combustion plants were collected and characterised...... for their composition and leaching properties. Despite the relatively large variations in the contents of nutrients and trace metals, the overall levels were comparable to typical ranges reported in the literature for other wood combustion ashes, as well as with regards to leaching. In general, the composition...

Multielement analysis of Zanthoxylum bungeanum Maxim. essential oil using ICP-MS/MS.

Science.gov (United States)

Fu, Liang; Xie, Hualin; Shi, Shuyun

2018-04-12

The concentrations of trace elements (Cr, Ni, As, Cd, Hg, and Pb) in Zanthoxylum bungeanum Maxim. essential oil (ZBMEO) were determined by inductively coupled plasma tandem mass spectrometry. The ZBMEO sample was directly analyzed after simple dilution with n-hexane. Aiming for a relatively high vapor pressure of n-hexane and its resultant loading on plasma, we used a narrow injector torch and optimized plasma radio frequency power and carrier gas flow to ensure stable operation of the plasma. An optional gas flow of 20% O 2 in Ar was added to the carrier gas to prevent the incomplete combustion of highly concentrated organic carbon in plasma and the deposition of carbon on the sampling and skimmer cone orifices. In tandem mass spectrometry mode, O 2 was added to the collision/reaction cell to eliminate the interferences. The limits of detection for Cr, Ni, As, Cd, Hg, and Pb were 2.26, 1.64, 2.02, 1.35, 1.76, and 0.97 ng L -1 , respectively. After determination of 23 ZBMEO samples from different regions in China, we found that the average concentration ranges of trace elements in the 23 ZBMEO samples were 0.72-6.02 ng g -1 , 0.09-2.87 ng g -1 , 0.21-5.84 ng g -1 , 0.16-2.15 ng g -1 , 0.13-0.92 ng g -1 , and 0.17-0.73 ng g -1 for Cr, Ni, As, Cd, Hg, and Pb, respectively. The trace elements in ZBMEO differed significantly when different extraction technologies were used. The study revealed that the contents of the toxic elements As, Cd, Hg, and Pb were extremely low, and hence they are unlikely to pose a health risk following ZBMEO ingestion. Graphical abstract The working mechanism of sample analysis by ICP-MS/MS.

Food Sensitivity in Children with Acute Urticaria in Skin Prick Test: Single Center Experience

Directory of Open Access Journals (Sweden)

Hatice Eke Gungor

2015-11-01

Full Text Available Aim: Families of children with acute urticaria often think that there is food allergy in children with urticaria and insist for skin tests. In this study, it was aimed to determine whether skin prick tests are necessary in cases presented with acute urticaria, in whom other causes of acute urticaria are excluded. Material and Method: A test panel involving cow milk, egg white, wheat, hazelnut, peanut, soybean, walnut, sesame, and tuna fish antigens was applied to the children presented with acute urticaria between 1 August 2013 and 1 August 2014, in whom other causes of acute urticaria were excluded and suspected food allergy was reported by parents. Results: Overall, 574 children aged 1-14 years were included to the study. Of the patients, sensitization against at least one food antigen was detected in 22.3% (128/574 of the patients. This rate was found to be 31.9% among those younger than 3 years, while 19.3% in those older than 3 years. Overall, sensitization rates against food allergen in panel were as follows: egg white, 7.3%; wheat, 3.3%; cow milk, 2.7%,; sesame, 2.8%; hazelnut, 2.4%; soybean, 2.3%; peanut, 1.9%, walnut, 1.6%; tuna fish, 1.6%. In general, the history of patients wasn%u2019t compatible with food sensitization detected. Discussion: Sensitization to food allergens is infrequent in children presented with acute urticaria, particularly among those older than 3 years despite expressions of parent and skin prick tests seems to be unnecessary unless strongly suggestive history is present.

Analysis list: Ash2l [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available Ash2l Blood + mm9 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/target/Ash2l.1.tsv... http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/target/Ash2l.5.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/target/Ash2...l.10.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/colo/Ash2l.Blood.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/colo/Blood.gml ...

Properties of Fly Ash Blocks Made from Adobe Mould

Science.gov (United States)

Chokhani, Alankrit; Divakar, B. S.; Jawalgi, Archana S.; Renukadevi, M. V.; Jagadish, K. S.

2018-06-01

Fly ash being one of the industrial waste products poses a serious disposal problem. This paper presents an experimental study of utilization of fly ash to produce blocks with varying proportions and mix combinations. Composition of fly ash blocks mainly consist of fly ash and sand, with cementitious product as either cement, lime or both, such as fly ash-sand-cement, fly ash-sand-lime and fly ash-sand-cement-lime are used. Four different proportions for each of the mix combinations are experimented. Compressive strength, water absorption, Initial rate of absorption, and dry density of fly ash blocks are studied. The influence of partial and complete replacement of cement by lime is examined.

Properties of Fly Ash Blocks Made from Adobe Mould

Science.gov (United States)

Chokhani, Alankrit; Divakar, B. S.; Jawalgi, Archana S.; Renukadevi, M. V.; Jagadish, K. S.

2018-02-01

Fly ash being one of the industrial waste products poses a serious disposal problem. This paper presents an experimental study of utilization of fly ash to produce blocks with varying proportions and mix combinations. Composition of fly ash blocks mainly consist of fly ash and sand, with cementitious product as either cement, lime or both, such as fly ash-sand-cement, fly ash-sand-lime and fly ash-sand-cement-lime are used. Four different proportions for each of the mix combinations are experimented. Compressive strength, water absorption, Initial rate of absorption, and dry density of fly ash blocks are studied. The influence of partial and complete replacement of cement by lime is examined.

Method of reversibly immobilizing sulfate ash

International Nuclear Information System (INIS)

Greenhalgh, W.O.

1984-01-01

A sulphate ash at least 20% by weight of which consists of sulphates of transuranic elements is immobilised by heating to melting a mixture of the ash, a metal, and a fluxing agent; the metal used is Al, Ce, Sm, Eu or mixtures thereof and it is used in an amount sufficient to reduce the transuranic sulphates in the ash to metal and form an alloy with the metal so produced; sufficient of the fluxing agent is used to reduce the percentage of transuranic sulphates in the mix to form 1% to 10% of the mix and the molten mixture is cooled and the alloy containing the immobilised ash separated. (author)

Impact of coal fly ash addition on ash transformation and deposition in a full-scale wood suspension-firing boiler

DEFF Research Database (Denmark)

Wu, Hao; Bashir, Muhammad Shafique; Jensen, Peter Arendt

2013-01-01

Ash transformation and deposition during pulverized wood combustion in a full-scale power plant boiler of 800 MWth were studied with and without the addition of coal fly ash. The transient ash deposition behavior was characterized by using an advanced deposit probe system at two boiler locations...... constant after a few hours. The formed deposits, especially those at the location with low flue gas temperatures, contained a considerable amount of K2SO4, KCl, and KOH/K2CO3. With the addition of a large amount (about 4 times of the mass flow of wood ash) of coal fly ash to the boiler, these alkali...

A Comparative study Of Catalityc Activity Of Heterogeneous Base Of Banana Stem Ash And Fly Ash On Production Of Biodiesel Byultrasonic

Directory of Open Access Journals (Sweden)

Marlinda

2015-08-01

Full Text Available Abstract The use of heterogeneous catalysts in the production of biodiesel provides many advantages due to heterogeneous catalysts can be easily separated from the product so that it can be reused. This research using heterogeneous catalysts derived from natural materials namely banana stem ash and coal fly ash containing alkali and alkaline earth elements. The preparation of catalyst from banana stem ash and coal fly ash used activator KOH 1.9 N and impregnation with KNO3 15 and then heated to a temperature of 550 0C for 3 hours. Results of preparation banana stem ash contains potassium of 36.52 and surface area of 41.901 m2g. This work presents the effect of ultrasonic assisted of waste cooking oil with methanol as solvent using banana stem ash and coal fly ash as catalyst. The diameter of catalyst particles of banana stem ash and coal fly ash varied at 50 100 150 200 and 250 mesh. The transesterification reaction was performed in the presence of ultrasonic operating frequency constant at 40 kHz methanol molar ratio to oil of 9 1 and reaction time of 30 minutes. The methyl ester biodiesel content of product was 93.26 of banana stems ash and 57 of coal fly ash respectively. The physical property was compared with the National Indonesia Standard SNI 2006 with a density viscosity cloud point flash point and cetane number.

Hospital waste ashes in Portland cement mortars

International Nuclear Information System (INIS)

Genazzini, C.; Zerbino, R.; Ronco, A.; Batic, O.; Giaccio, G.

2003-01-01

Nowadays, most concretes incorporate mineral additions such as pozzolans, fly ash, silica fume, blast furnace slag, and calcareous filler among others. Although the technological and economical benefits were the main reasons for the use of mineral additions, the prevention of environmental contamination by means of proper waste disposal becomes a priority. The chance of incorporating hospital waste ashes in Portland cement-based materials is presented here. Ash characterization was performed by chemical analysis, X-ray diffraction, radioactive material detection, and fineness and density tests. Conduction calorimetry and setting time tests were developed on pastes including ash contents from 0% to 100%. Mortars were prepared including ash contents up to 50% of cement. The results of setting time, temperature development, flexural and compressive strengths, water absorption, density, and leachability are analyzed. Results indicate that Portland cement systems could become an alternative for the disposal of this type of ashes

Physico-chemical characterisation of Indian biomass ashes

Energy Technology Data Exchange (ETDEWEB)

K. Umamaheswaran; Vidya S. Batra [Energy and Resources Institute (TERI), New Delhi (India)

2008-05-15

India stands fourth in biomass utilisation for various purposes like domestic, commercial and industrial applications. While extensive studies have been made for coal ash characterisation and utilisation, studies on characterisation of biomass ash and its utilisation has not been addressed. In this paper, biomass ash from five sources i.e. rice husk, bagasse, groundnut shell, cashewnut shell, and arecanut shell have been characterised. Chemical composition analysis, particle size analysis, thermal analysis, and microstructure analysis were carried out. Results show that in all ashes silica is the major compound with particle size ranging from 15 to 30 {mu}m and having irregular shape. Ash powders originating from cashewnut shell, arecanut shell and groundnut shell also have compounds of calcium, magnesium and potassium. Bagasse and cashewnut shell ashes have high LOI due to presence of unburnt carbon, P{sub 2}O{sub 5} and other volatiles. 16 refs., 22 figs., 3 tabs.

Design of a hydraulic ash transport system

Energy Technology Data Exchange (ETDEWEB)

Mirgorodskii, V.G.; Mova, M.E.; Korenev, V.E.; Grechikhin, Yu.A. (Donetskii Politekhnicheskii Institut (USSR))

1990-04-01

Discusses general design of a hydraulic ash removal system to be employed at the reconstructed six 225 MW blocks of the Mironov State Regional Power Plant in the USSR. The blocks burn low-grade solid fuel with an ash content of up to 40.5%. Large quantities of ash have to be moved from the plant (total ash production 60 t/h, using 570 t/h of water for cooling and moistening). An optimum hydraulic ash transportation system would include a two-section airlift pumping system, shown in a diagram. Technological advantages of using this airlift system are enumerated, including short pipes, reduction in required water quantity and the possibility of siting hydraulic pumps at zero level.

Prospects for long-term ash survival in the core emerald ash borer mortality zone

Science.gov (United States)

Jordan M. Marshall; Andrew J. Storer; Roger Mech; Steven A. Katovich

2011-01-01

Attacking all North American ash species (Fraxinus spp.), emerald ash borer (EAB) (Agrilus planipennis Fairmaire) has caused significant mortality within its introduced range. For other forest pests, host bark plays an important role in infestation density and oviposition behavior. The objectives of this study were to (1) locate...

Synthesis of geopolymer from biomass-coal ash blends

Science.gov (United States)

Samadhi, Tjokorde Walmiki; Wulandari, Winny; Prasetyo, Muhammad Iqbal; Fernando, Muhammad Rizki; Purbasari, Aprilina

2017-09-01

Geopolymer is an environmentally attractive Portland cement substitute, owing to its lower carbon footprint and its ability to consume various aluminosilicate waste materials as its precursors. This work describes the development of geopolymer formulation based on biomass-coal ash blends, which is predicted to be the prevalent type of waste when biomass-based thermal energy production becomes mainstream in Indonesia. The ash blends contain an ASTM Class F coal fly ash (FA), rice husk ash (RHA), and coconut shell ash (CSA). A mixture of Na2SiO3 and concentrated KOH is used as the activator solution. A preliminary experiment identified the appropriate activator/ash mass ratio to be 2.0, while the activator Na2SiO3/KOH ratio varies from 0.8 to 2.0 with increasing ash blend Si/Al ratio. Both non-blended FA and CSA are able to produce geopolymer mortars with 7-day compressive strength exceeding the Indonesian national SNI 15-2049-2004 standard minimum value of 2.0 MPa stipulated for Portland cement mortars. Ash blends have to be formulated with a maximum RHA content of approximately 50 %-mass to yield satisfactory 7-day strength. No optimum ash blend composition is identified within the simplex ternary ash blend compositional region. The strength decreases with Si/Al ratio of the ash blends due to increasing amount of unreacted silicate raw materials at the end of the geopolymer hardening period. Overall, it is confirmed that CSA and blended RHA are feasible raw materials for geopolymer production..

Characterization of ash pond ashes from 3rd thermal power plant by SEM/EDX and XRD methods

Directory of Open Access Journals (Sweden)

A Minjigmaa

2014-10-01

Full Text Available   Coal combustion by products from ash pond of 3rdthermal power plant of Ulaanbaatar city have been collected in 2010 and 2013 years. The ash samples have been characterized by XRD, XRF and SEM-EDX methods in order to evaluate their chemical and mineralogical composition changes with disposed times. The mineralogical composition of ash varies with time though the chemical composition of the ashes were close each other. Possibly, inefficient operating condition of the TPS shows influence on the mineralogical composition.DOI: http://dx.doi.org/10.5564/mjc.v14i0.201Mongolian Journal of Chemistry 14 (40, 2013, p61-65

Leaching from biomass combustion ash

DEFF Research Database (Denmark)

Maresca, Alberto; Astrup, Thomas Fruergaard

2014-01-01

The use of biomass combustion ashes for fertilizing and liming purposes has been widely addressed in scientific literature. Nevertheless, the content of potentially toxic compounds raises concerns for a possible contamination of the soil. During this study five ash samples generated at four...

Improved prediction and tracking of volcanic ash clouds

Science.gov (United States)

Mastin, Larry G.; Webley, Peter

2009-01-01

During the past 30??years, more than 100 airplanes have inadvertently flown through clouds of volcanic ash from erupting volcanoes. Such encounters have caused millions of dollars in damage to the aircraft and have endangered the lives of tens of thousands of passengers. In a few severe cases, total engine failure resulted when ash was ingested into turbines and coating turbine blades. These incidents have prompted the establishment of cooperative efforts by the International Civil Aviation Organization and the volcanological community to provide rapid notification of eruptive activity, and to monitor and forecast the trajectories of ash clouds so that they can be avoided by air traffic. Ash-cloud properties such as plume height, ash concentration, and three-dimensional ash distribution have been monitored through non-conventional remote sensing techniques that are under active development. Forecasting the trajectories of ash clouds has required the development of volcanic ash transport and dispersion models that can calculate the path of an ash cloud over the scale of a continent or a hemisphere. Volcanological inputs to these models, such as plume height, mass eruption rate, eruption duration, ash distribution with altitude, and grain-size distribution, must be assigned in real time during an event, often with limited observations. Databases and protocols are currently being developed that allow for rapid assignment of such source parameters. In this paper, we summarize how an interdisciplinary working group on eruption source parameters has been instigating research to improve upon the current understanding of volcanic ash cloud characterization and predictions. Improved predictions of ash cloud movement and air fall will aid in making better hazard assessments for aviation and for public health and air quality. ?? 2008 Elsevier B.V.

Ash chemistry and sintering, verification of the mechanisms

Energy Technology Data Exchange (ETDEWEB)

Hupa, M.; Skrifvars, B.J. [Aabo Akademi, Turku (Finland)

1996-12-01

In this project four sintering mechanisms have been studied, i.e., partial melting with a viscous liquid, partial melting with a non-viscous liquid, chemical reaction sintering and solid state sintering. The work has aimed at improving the understanding of ash sintering mechanisms and quantifying their role in combustion and gasification. The work has been oriented in particular on the understanding of biomass ash behavior. The work has not directly focused on any specific technical application. However, results can also be applied on other fuels such as brown coal, petroleum coke, black liquor and different types of wastes (PDF, RDF, MSW). In one part of study the melting behavior was calculated for ten biomass ashes and compared with lab measurements of sintering tendencies. The comparison showed that the T{sub 15} temperatures, i.e. those temperatures at which the ashes contained 15 % molten phase, correlated fairly well with the temperature at which the sintering measurements detected sintering. This suggests that partial melting can be predicted fairly accurate for some ashes already with the today existing thermodynamic calculation routines. In some cases, however the melting calculations did not correlate with the detected sintering temperatures. In a second part detailed measurements on ash behavior was conducted both in a semi full scale CFB and a lab scale FBC. Ashes and deposits were collected and analyzed in several different ways. These analyses show that the ash chemistry shifts radically when the fuel is shifted. Fuels with silicate based ashes behaved totally different than those with an oxide or salt based ash. The chemistry was also affected by fuel blending. The ultimate goal has been to be able to predict the ash thermal behavior during biomass thermal conversion, using the fuel and ash elemental analyses and a few operational key parameters as the only input data. This goal has not yet today been achieved. (author)

Radiobiological waste treatment-ashing treatment and immobilization with cement

Energy Technology Data Exchange (ETDEWEB)

Shengtao, Feng; Li, Gong; Li, Cheng; Benli, Wang; Lihong, Wang [China Inst. for Radiation Protection, Taiyuan, Shanxi (China)

1997-02-01

This report describes the results of the study on the treatment of radioactive biological waste in the China Institute for Radiation Protection (CIRP). The possibility of radiobiological waste treatment was investigated by using a RAF-3 type rapid ashing apparatus together with the immobilization of the resulted ash. This rapid ashing apparatus, developed by CIRP, is usually used for pretreatment of samples prior to chemical analysis and physical measurements. The results show that it can ash 3 kg of animal carcasses a batch, the ashing time is 5-7 h and the ash content is less than 4 wt%. The ashing temperature not exceeding 450 deg. C was used without any risk of high losses of radionuclides. The ash from the rapid ashing apparatus was demonstrated to be immobilized with ordinary silicate cement. The optimum cement/ash/water formulation of the cemented waste form was 35 {+-} 5 wt% cement, 29 {+-} 2 wt% water, and 36 {+-} 6 wt% ash. The performance of the waste form was in compliance with the technical requirements except for impact resistance. Mixing additives in immobilization formulations can improve the performance of the cemented ash waste form. The additives chosen were DH{sub 4A} flow promoter as a cement additive and vermiculite or zeolite as a supplement. The recommended formulation, i.e. an improved formulation of the cemented ash waste form is that additives DH{sub 4A} flow promoter and vermiculite (or zeolite) are added on the ground of optimum cement/ash/water formulation of the cemented waste form, the dosage of water, DH{sub 4A} and vermiculite (or zeolite) is 70 wt%, 0.5 wt% and {<=} 5 wt% of the cement dosage, respectively. The cemented ash waste forms obtained meet all the requirements for disposal. (author). 12 refs, 7 figs, 13 tabs.

Radiobiological waste treatment-ashing treatment and immobilization with cement

International Nuclear Information System (INIS)

Feng Shengtao; Gong Li; Cheng Li; Wang Benli; Wang Lihong

1997-01-01

This report describes the results of the study on the treatment of radioactive biological waste in the China Institute for Radiation Protection (CIRP). The possibility of radiobiological waste treatment was investigated by using a RAF-3 type rapid ashing apparatus together with the immobilization of the resulted ash. This rapid ashing apparatus, developed by CIRP, is usually used for pretreatment of samples prior to chemical analysis and physical measurements. The results show that it can ash 3 kg of animal carcasses a batch, the ashing time is 5-7 h and the ash content is less than 4 wt%. The ashing temperature not exceeding 450 deg. C was used without any risk of high losses of radionuclides. The ash from the rapid ashing apparatus was demonstrated to be immobilized with ordinary silicate cement. The optimum cement/ash/water formulation of the cemented waste form was 35 ± 5 wt% cement, 29 ± 2 wt% water, and 36 ± 6 wt% ash. The performance of the waste form was in compliance with the technical requirements except for impact resistance. Mixing additives in immobilization formulations can improve the performance of the cemented ash waste form. The additives chosen were DH 4A flow promoter as a cement additive and vermiculite or zeolite as a supplement. The recommended formulation, i.e. an improved formulation of the cemented ash waste form is that additives DH 4A flow promoter and vermiculite (or zeolite) are added on the ground of optimum cement/ash/water formulation of the cemented waste form, the dosage of water, DH 4A and vermiculite (or zeolite) is 70 wt%, 0.5 wt% and ≤ 5 wt% of the cement dosage, respectively. The cemented ash waste forms obtained meet all the requirements for disposal. (author). 12 refs, 7 figs, 13 tabs

Zanthoxylum bungeanum Maxim. (Rutaceae: A Systematic Review of Its Traditional Uses, Botany, Phytochemistry, Pharmacology, Pharmacokinetics, and Toxicology

Directory of Open Access Journals (Sweden)

Mengmeng Zhang

2017-10-01

Full Text Available Zanthoxylum bungeanum Maxim. (Rutaceae is a popular food additive and traditional Chinese herbal medicine commonly named HuaJiao in China. This plant is widely distributed in Asian countries. The aim of this paper is to provide a systematic review on the traditional usages, botany, phytochemistry, pharmacology, pharmacokinetics, and toxicology of this plant. Furthermore, the possible development and perspectives for future research on this plant are also discussed. To date, over 140 compounds have been isolated and identified from Z. bungeanum, including alkaloids, terpenoids, flavonoids, and free fatty acids. The extracts and compounds have been shown to possess wide-ranging biological activity, such as anti-inflammatory and analgesic effects, antioxidant and anti-tumor effects, antibacterial and antifungal effects, as well as regulatory effects on the gastrointestinal system and nervous system, and other effects. As a traditional herbal medicine, Z. bungeanum has been widely used to treat many diseases, especially digestive disorders, toothache, stomach ache, and diarrhea. Many traditional usages of this plant have been validated by present investigations. However, further research elucidating the structure-function relationship among chemical compounds, understanding the mechanism of unique sensation, as well as exploring new clinical effects and establishing criteria for quality control for Z. bungeanum should be further studied.

Zanthoxylum bungeanum Maxim. (Rutaceae): A Systematic Review of Its Traditional Uses, Botany, Phytochemistry, Pharmacology, Pharmacokinetics, and Toxicology.

Science.gov (United States)

Zhang, Mengmeng; Wang, Jiaolong; Zhu, Lei; Li, Tao; Jiang, Weidong; Zhou, Juan; Peng, Wei; Wu, Chunjie

2017-10-18

Zanthoxylum bungeanum Maxim. (Rutaceae) is a popular food additive and traditional Chinese herbal medicine commonly named HuaJiao in China. This plant is widely distributed in Asian countries. The aim of this paper is to provide a systematic review on the traditional usages, botany, phytochemistry, pharmacology, pharmacokinetics, and toxicology of this plant. Furthermore, the possible development and perspectives for future research on this plant are also discussed. To date, over 140 compounds have been isolated and identified from Z. bungeanum , including alkaloids, terpenoids, flavonoids, and free fatty acids. The extracts and compounds have been shown to possess wide-ranging biological activity, such as anti-inflammatory and analgesic effects, antioxidant and anti-tumor effects, antibacterial and antifungal effects, as well as regulatory effects on the gastrointestinal system and nervous system, and other effects. As a traditional herbal medicine, Z. bungeanum has been widely used to treat many diseases, especially digestive disorders, toothache, stomach ache, and diarrhea. Many traditional usages of this plant have been validated by present investigations. However, further research elucidating the structure-function relationship among chemical compounds, understanding the mechanism of unique sensation, as well as exploring new clinical effects and establishing criteria for quality control for Z. bungeanum should be further studied.

Future fly ash marketing; Flugaschevermarktung in der Zukunft

Energy Technology Data Exchange (ETDEWEB)

Mauder, R.; Hugot, A. [Evonik Power Minerals GmbH, Dinslaken (Germany)

2008-07-01

It can be assumed that the fly ash production volumes will undergo a marked increase over the next few years. The conditions of fly ash production will improve as a result of modern and refurbished power plants, yielding a positive effect on the quality of fly ashes. Other vital parameters of future fly ash marketing are fly ash logistics and the infrastructure of power plants. Basically, economic utilisation of the increased production volumes is possible; however, new and long-term strategies are necessary. (orig.)

Recirculation of biomass ashes onto forest soils: Ash composition, mineralogy and leaching properties

DEFF Research Database (Denmark)

Maresca, Alberto; Hyks, J.; Astrup, Thomas Fruergaard

2017-01-01

In Denmark, increasing amounts of wood ashes are generated from biomass combustion for energy production. The utilisation of ashes on top of forest soil for liming purposes has been proposed asan alternative to landfilling. Danish wood ash samples were collected and characterised with respect......, minor and trace elements were affected significantly by pH: high releases of PO4 3-, Mg, Zn, Cu and Cd were found for acidic conditions relevant to forest soils, while the highest releases of Mo and Cr were observed in alkaline conditions. Mineral phases were selected based on XRD analyses...... critical element compared with soil quality criteria, whereas the maximum theoretical loads of Ba, Cd, Cr, Sr, Mo, Ni, Pb, Sb, Se, Sn and V were relatively low....

Aggregate material formulated with MSWI bottom ash and APC fly ash for use as secondary building material

International Nuclear Information System (INIS)

Valle-Zermeño, R. del; Formosa, J.; Chimenos, J.M.; Martínez, M.; Fernández, A.I.

2013-01-01

Highlights: ► A concrete formulation was optimized using Bottom Ash and APC ash. ► 10% of APC ash achieves good compromise between economic and performance aspects. ► The crushed concrete was evaluated as secondary building granular material. ► The environmental behavior allows its use as secondary material. ► The abrasion resistance is not good enough for its use as a road sub-base material. - Abstract: The main goal of this paper is to obtain a granular material formulated with Municipal Solid Waste Incineration (MSWI) bottom ash (BA) and air pollution control (APC) fly ash to be used as secondary building material. Previously, an optimum concrete mixture using both MSWI residues as aggregates was formulated. A compromise between the environmental behavior whilst maximizing the reuse of APC fly ash was considered and assessed. Unconfined compressive strength and abrasion resistance values were measured in order to evaluate the mechanical properties. From these results, the granular mixture was not suited for certain applications owing to the high BA/APC fly ash content and low cement percentages used to reduce the costs of the final product. Nevertheless, the leaching test performed showed that the concentrations of all heavy metals were below the limits established by the current Catalan legislation for their reutilization. Therefore, the material studied might be mainly used in embankments, where high mechanical properties are not needed and environmental safety is assured

Production of mineral ash-wool

International Nuclear Information System (INIS)

Micevic, Z.; Djekic, S.

1996-01-01

The project entitled 'Production of Mineral Ash-Wool' presents a new technology of possible use of the fly ash, generated as a waste product from the fossil fueled power plants, as a basic raw material for manufacturing of different products from a new mineral ash-wool. The wide area of mineral ash-wool application (civil engineering, industry, power generation, etc.) and the advantages of this new technology (important raw material obtained free of charge, substitution of expensive silicate stone, use of electric energy for melting instead for coke, vicinity of factory location close to the fossil fueled power plant, lower product price, reduction of environmental pollution, etc.) have resulted in the performance of the bench scale tests. Positive results have been obtained, as a good initial base for the realization of this project. The named study as an detailed analysis has been carried out for the assessment of: supply and sales market, analysis of possible and selection of an optimal location of the factory in the frame of fossil fueled power plant 'Kosovo', selection of the production capacity and alternative preliminary technical designs of the factory for the mineral ash-wool production. For the studied alternatives, specifications and capital investments evaluations for equipment and works (mechanical, civil engineering and electromechanical part) have been made as well as assessments of production costs. Based on the performed economical and financial analyses, as well as the sensitivity analyses one could be concluded that the investments in the factory for the mineral ash-wool production is highly economically acceptable. (author). 1 fig., 1 tab., 3 refs

Coal ash parameters by neutron activation

International Nuclear Information System (INIS)

Chrusciel, Edward; Chau, N.D.; Niewodniczanski, J.W.

1994-01-01

The coal parameters, ash content and ash slagging index, may be strongly related to the chemical composition of mineral impurities in coal. Based on this assumption the authors have examined the feasibility of neutron activation techniques, both as a laboratory and a well logging method, by recording induced γ-rays in the two energy intervals with the help of a scintillation γ-ray spectrometer. Results from the Upper Silesiab Coal Basin have shown that the method can be used to evaluate the ash content and ash fusion temperature, both in the laboratory and in well logging; the corresponding mean standard deviations being 1.5 wt% and 35 o C; and 3 wt% and 45 o C respectively. (author)

Basic soil benefits from ash utilization

Energy Technology Data Exchange (ETDEWEB)

Martens, D.C.; Plank, C.O.

1970-01-01

The beneficial effects of fly ash application shown herein are expected to encourage future disposal of the material in agricultural soils. It is foreseen, however, that fly ash disposal in agricultural soils would be unsuccessful if adverse effects on crop production result from its misuse. It seems evident, therefore, that quality control measures will be required to insure proper disposal of the material in agricultural soils. It will be necessary to consider differences in chemical properties of various samples of fly ash and in chemical reactions of samples of fly ash and soils. Differences in tolerances of plants to soluble salt damage and to specific nutrient deficiencies and toxicities will also have to be taken into account. 9 tables.

Residual Ash Formation during Suspension-Firing of Biomass

DEFF Research Database (Denmark)

Damø, Anne Juul; Jappe Frandsen, Flemming; Jensen, Peter Arendt

2014-01-01

Through 50+ years, high quality research has been conducted in order to characterize ash and deposit formation in utility boilers fired with coal, biomass and waste fractions. The basic mechanism of fly ash formation in suspension fired coal boilers is well described, documented and may even...... be modeled relatively precisely. Concerning fly ash formation from biomass or waste fractions, the situation is not nearly as good. Lots of data are available from campaigns where different ash fractions, including sometimes also in-situ ash, have been collected and analyzed chemically and for particle size...... distribution. Thus, there is a good flair of the chemistry of fly ash formed in plants fired with biomass or waste fractions, either alone, or in conjunction with coal. But data on dedicated studies of the physical size development of fly ash, are almost non-existing for biomasses and waste fractions...

Plant growth on 'fly ash'

Energy Technology Data Exchange (ETDEWEB)

Holliday, R; Hodgson, D R; Townsend, W N; Wood, J W

1958-04-12

Plants were grown in plot and pot experiments to assess the toxicity of the fly ash. It was found that plants grouped into three classes: tolerant, moderately tolerant, and sensitive. Boron was found to be a major compoent of the toxic principle of fly ash.

Measuring ash content of coal

International Nuclear Information System (INIS)

Clayton, C.G.; Wormald, M.R.

1980-01-01

An apparatus for measuring the ash content of coal is claimed. It comprises a means for irradiating a known quantity of coal in a transport container with a known dose of neutrons, a means for detecting γ-rays having a predetermined energy emitted by the irradiated coal, the γ-rays being indicative of the presence of an ash-forming element in the coal, a means for producing a signal related to the intensity of the γ-ray emission and a means responsive to the signal to provide an indication of the concentration of the ash-forming element in the coal

Water table response to harvesting and simulated emerald ash borer mortality in black ash wetlands in Minnesota, USA

Science.gov (United States)

Robert A. Slesak; Christian F. Lenhart; Kenneth N. Brooks; Anthony W. D' Amato; Brian J. Palik

2014-01-01

Black ash wetlands are seriously threatened because of the invasive emerald ash borer (EAB). Wetland hydrology is likely to be modified following ash mortality, but the magnitude of hydrological impact following loss via EAB and alternative mitigation harvests is not clear. Our objective was to assess the water table response to simulated EAB and harvesting to...

Combustion of Biosolids in a Bubbling Fluidized Bed, Part 1: Main Ash-Forming Elements and Ash Distribution with a Focus on Phosphorus.

Science.gov (United States)

Skoglund, Nils; Grimm, Alejandro; Ohman, Marcus; Boström, Dan

2014-02-20

This is the first in a series of three papers describing combustion of biosolids in a 5-kW bubbling fluidized bed, the ash chemistry, and possible application of the ash produced as a fertilizing agent. This part of the study aims to clarify whether the distribution of main ash forming elements from biosolids can be changed by modifying the fuel matrix, the crystalline compounds of which can be identified in the raw materials and what role the total composition may play for which compounds are formed during combustion. The biosolids were subjected to low-temperature ashing to investigate which crystalline compounds that were present in the raw materials. Combustion experiments of two different types of biosolids were conducted in a 5-kW benchscale bubbling fluidized bed at two different bed temperatures and with two different additives. The additives were chosen to investigate whether the addition of alkali (K 2 CO 3 ) and alkaline-earth metal (CaCO 3 ) would affect the speciation of phosphorus, so the molar ratios targeted in modified fuels were P:K = 1:1 and P:K:Ca = 1:1:1, respectively. After combustion the ash fractions were collected, the ash distribution was determined and the ash fractions were analyzed with regards to elemental composition (ICP-AES and SEM-EDS) and part of the bed ash was also analyzed qualitatively using XRD. There was no evidence of zeolites in the unmodified fuels, based on low-temperature ashing. During combustion, the biosolid pellets formed large bed ash particles, ash pellets, which contained most of the total ash content (54%-95% (w/w)). This ash fraction contained most of the phosphorus found in the ash and the only phosphate that was identified was a whitlockite, Ca 9 (K,Mg,Fe)(PO 4 ) 7 , for all fuels and fuel mixtures. With the addition of potassium, cristobalite (SiO 2 ) could no longer be identified via X-ray diffraction (XRD) in the bed ash particles and leucite (KAlSi 2 O 6 ) was formed. Most of the alkaline-earth metals

Expansion control for cementation of incinerated ash

International Nuclear Information System (INIS)

Nakayama, T.; Suzuki, S.; Hanada, K.; Tomioka, O.; Sato, J.; Irisawa, K.; Kato, J.; Kawato, Y.; Meguro, Y.

2015-01-01

A method, in which incinerated ash is solidified with a cement material, has been developed to dispose of radioactive incinerated ash waste. A small amount of metallic Al, which was not oxidized in the incineration, existed in the ash. When such ash was mixed with a cement material and water, alkaline components in the ash and the cement were dissolved in the mixing water and then metallic Al reaction with the alkaline compounds resulted in generation of H 2 . Because the H 2 generation began immediately just after the mixing, H 2 bubbles pushed up the mixed grout material and an expanded solidified form was obtained. The expansion leads to lowering the strength of the solidified form and making harmful void. In this study, we tried to control H 2 generation from the reaction of metallic Al in the cementation by means of following two methods, one was a method to let metallic Al react prior to the cementation and the other was a method to add an expansion inhibitor that made an oxide film on the surface of metallic Al. In the pre-treatment, the ash was soaked in water in order to let metallic Al react with it, and then the ash with the immersion solution was dried at 105 Celsius degrees. The pre-treated ash was mixed with an ordinary portland cement and water. The inhibitor of lithium nitrite, sodium nitrite, phosphoric acid, or potassium dihydrogen phosphate was added at the mixing process. The solidified forms prepared using the pre-treated ash and lithium nitrite were not expanded. Phosphoric acid and sodium nitrite were effective for expansion control, but potassium dihydrogen phosphate did not work. (authors)

Distribution of trunk-injected 14C-imidacloprid in ash trees and effects on emerald ash borer (Coleoptera: Buprestidae) adults

Science.gov (United States)

David Mota-Sánchez; Bert M. Cregg; Deborah G. McCullough; Therese M. Poland; Robert M. Hollingworth

2009-01-01

The emerald ash borer (EAB), Agrilus planipennis (Coleoptera: Buprestidae) is a destructive exotic pest of North American ash (Fraxinus sp.) trees. Trunk injection of imidacloprid is commonly used to protect landscape ash trees from A. planipennis damage. Efficacy can vary and little is known about the...

Bottom ash handling: why the outlook is dry

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-03-15

The author believes that dry systems are the way forward for bottom ash handling at coal fired power plants. The first two commercial installations of Clyde Bergemann's DRYCON system, in China, are due to enter operation shortly. The DRY ash CONveyor (DRYCON) employs fresh air flow to cool the ash, returning reheat energy to the boiler. It also addresses some problems encountered with previous dry technologies whilst increasing ash capacity and enhancing ash cooking. The advantages of the DRYCON over the wet submerged scraper conveyor are listed. 7 figs.

IgE Sensitization Patterns to Commonly Consumed Foods Determined by Skin Prick Test in Korean Adults

OpenAIRE

Kim, Sung Ryeol; Park, Hye Jung; Park, Kyung Hee; Lee, Jae-Hyun; Park, Jung-Won

2016-01-01

Offending food allergens can vary with regional preferences in food consumption. In this study, we analysed sensitization rates to commonly consumed foods in Korean adults suspected of having food allergy. One hundred and thirty four subjects underwent a skin prick test (SPT) with 55 food allergens, of which 13 were made by our laboratory and the rest were commercially purchased. Of the 134 patients, 73 (54.5%) were sensitized to one or more food allergens. Sensitization to chrysalis was dete...

Phytochemical profiles and biological activity evaluation of Zanthoxylum bungeanum Maxim seed against asthma in murine models.

Science.gov (United States)

Tang, Weizhuo; Xie, Qiangmin; Guan, Jian; Jin, Saihong; Zhao, Yuqing

2014-03-28

Zanthoxylum bungeanum Maxim seed (ZBMS) has been used in Traditional Chinese Medicine (TCM) as an ingredient of polyherbal formulations for the treatment of inflammation and asthma. The aim of this study was to analyze the major composition and to evaluate the anti-asthma activity of ZBMS. Some murine models including acetylcholine/histamine-induced asthma, ovalbumin-induced airway inflammation, ear edema and toe swelling measurement, citric acid-induced cough, and anti-stress abilities were investigated to fully study the anti-asthma activity of ZBMS.GC chromatography was also performed to analyze the major fatty acid composition of ZBMS. The results demonstrated that the major fatty acid composition of ZBMS includes oleic acid (20.15%), linoleic acid (26.54%), and α-linolenic acid (30.57%), which was the leading component of ZBMS, and that the total fatty acid content of ZBMS was 77.27%. The murine models demonstrated that ZBMS displays a protective effect on guinea pig sensitization, a dose-dependent inhibition of the increases in RL and decreases in Cdyn, which resulted in the relief of auricle edema and toe swelling in mice and anti-stress activity. Our results validate the traditional use of ZBMS for the treatment of asthma and other inflammatory joint disorders, and suggest that ZBMS has potential as a new therapeutic agent for asthma management. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

National volcanic ash operations plan for aviation

Science.gov (United States)

,; ,

2007-01-01

The National Aviation Weather Program Strategic Plan (1997) and the National Aviation Weather Initiatives (1999) both identified volcanic ash as a high-priority informational need to aviation services. The risk to aviation from airborne volcanic ash is known and includes degraded engine performance (including flameout), loss of visibility, failure of critical navigational and operational instruments, and, in the worse case, loss of life. The immediate costs for aircraft encountering a dense plume are potentially major—damages up to $80 million have occurred to a single aircraft. Aircraft encountering less dense volcanic ash clouds can incur longer-term costs due to increased maintenance of engines and external surfaces. The overall goal, as stated in the Initiatives, is to eliminate encounters with ash that could degrade the in-flight safety of aircrews and passengers and cause damage to the aircraft. This goal can be accomplished by improving the ability to detect, track, and forecast hazardous ash clouds and to provide adequate warnings to the aviation community on the present and future location of the cloud. To reach this goal, the National Aviation Weather Program established three objectives: (1) prevention of accidental encounters with hazardous clouds; (2) reduction of air traffic delays, diversions, or evasive actions when hazardous clouds are present; and (3) the development of a single, worldwide standard for exchange of information on airborne hazardous materials. To that end, over the last several years, based on numerous documents (including an OFCMsponsored comprehensive study on aviation training and an update of Aviation Weather Programs/Projects), user forums, and two International Conferences on Volcanic Ash and Aviation Safety (1992 and 2004), the Working Group for Volcanic Ash (WG/VA), under the OFCM-sponsored Committee for Aviation Services and Research, developed the National Volcanic Ash Operations Plan for Aviation and Support of the

Emerald ash borer life cycle

Science.gov (United States)

Leah S. Bauer; Robert A. Haack; Deborah L. Miller; Toby R. Petrice; Houping Liu

2004-01-01

The emerald ash borer (EAB), Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), native to several Asian countries, was discovered in southeastern Michigan and nearby Ontario in June of 2002. EAB was identified as the cause of extensive ash (Fraxinus spp.) mortality in approximately 2,500 mi2, and...

Emerald Ash Borer (Coleoptera: Buprestidae)

Science.gov (United States)

The emerald ash borer, Agrilus planipennis Fairmaire, is an invasive beetle from Asia that has caused large scale ash (Fraxinus spp.) mortality in North America. This book chapter reviews the taxonomy, biology, life history of this invasive pest and its associated natural enemies in both its native ...

Study on preparation method of Zanthoxylum bungeanum seeds kernel oil with zero trans-fatty acids.

Science.gov (United States)

Liu, Tong; Yao, Shi-Yong; Yin, Zhong-Yi; Zheng, Xu-Xu; Shen, Yu

2016-04-01

The seed of Zanthoxylum bungeanum (Z. bungeanum) is a by-product of pepper production and rich in unsaturated fatty acid, cellulose, and protein. The seed oil obtained from traditional producing process by squeezing or extracting would be bad quality and could not be used as edible oil. In this paper, a new preparation method of Z. bungeanum seed kernel oil (ZSKO) was developed by comparing the advantages and disadvantages of alkali saponification-cold squeezing, alkali saponification-solvent extraction, and alkali saponification-supercritical fluid extraction with carbon dioxide (SFE-CO2). The results showed that the alkali saponification-cold squeezing could be the optimal preparation method of ZSKO, which contained the following steps: Z. bungeanum seed was pretreated by alkali saponification under the conditions of adding 10 %NaOH (w/w), solution temperature was 80 °C, and saponification reaction time was 45 min, and pretreated seed was separated by filtering, water washing, and overnight drying at 50 °C, then repeated squeezing was taken until no oil generated at 60 °C with 15 % moisture content, and ZSKO was attained finally using centrifuge. The produced ZSKO contained more than 90 % unsaturated fatty acids and no trans-fatty acids and be testified as a good edible oil with low-value level of acid and peroxide. It was demonstrated that the alkali saponification-cold squeezing process could be scaled up and applied to industrialized production of ZSKO.

The effect of fly ash and coconut fibre ash as cement replacement materials on cement paste strength

Science.gov (United States)

Bayuaji, R.; Kurniawan, R. W.; Yasin, A. K.; Fatoni, H. AT; Lutfi, F. M. A.

2016-04-01

Concrete is the backbone material in the construction field. The main concept of the concrete material is composed of a binder and filler. Cement, concrete main binder highlighted by environmentalists as one of the industry are not environmentally friendly because of the burning of cement raw materials in the kiln requires energy up to a temperature of 1450° C and the output air waste CO2. On the other hand, the compound content of cement that can be utilized in innovation is Calcium Hydroxide (CaOH), this compound will react with pozzolan material and produces additional strength and durability of concrete, Calcium Silicate Hydrates (CSH). The objective of this research is to explore coconut fibers ash and fly ash. This material was used as cement replacement materials on cement paste. Experimental method was used in this study. SNI-03-1974-1990 is standard used to clarify the compressive strength of cement paste at the age of 7 days. The result of this study that the optimum composition of coconut fiber ash and fly ash to substitute 30% of cement with 25% and 5% for coconut fibers ash and fly ash with similar strength if to be compared normal cement paste.

Volcanic Ash fall Impact on Vegetation, Colima 2005

Science.gov (United States)

Garcia, M. G.; Martin, A.; Fonseca, R.; Nieto, A.; Radillo, R.; Armienta, M.

2007-05-01

An ash sampling network was established arround Colima Volcano in 2005. Ash fall was sampled on the North, Northeast, East, Southeast, South, Southwest and West of the volcano. Samples were analyzed for ash components, geochemistry and leachates. Ash fall ocurred on April (12), May (10, 23), June (2, 6, 9, 10, 12, 14), July (27), September (27), October (23) and November (24). Most of the ash is made of andesitic dome-lithics but shows diferences in crystal, juvenile material and lithic content. In May, some samples contained grey and dark pumice (scoria). Texture varies from phi >4 to phi 0. Leachate concentration were low: SO4 (7.33-54.19) Cl- (2.29-4.97) and F- (0.16-0.37). During 2005, Colima Volcano's ash fall rotted some of the guava and peach fruits and had a drying effect on spearment and epazote plants. Even these small ash amounts could have hindered sugar cane and agave growth.

Ash transformation during co-firing coal and straw

DEFF Research Database (Denmark)

Zheng, Yuanjing; Jensen, Peter Arendt; Jensen, Anker Degn

2007-01-01

Co-firing straw with coal in pulverized fuel boilers can cause problems related to fly ash utilization, deposit formation, corrosion and SCR catalyst deactivation due to the high contents of Cl and K in the ash. To investigate the interaction between coal and straw ash and the effect of coal...... quality on fly ash and deposit properties, straw was co-fired with three kinds of coal in an entrained flow reactor. The compositions of the produced ashes were compared to the available literature data to find suitable scaling parameters that can be used to predict the composition of ash from straw...... and coal co-firing. Reasonable agreement in fly ash compositions regarding total K and fraction of water soluble K was obtained between co-firing in an entrained flow reactor and full-scale plants. Capture of potassium and subsequent release of HCl can be achieved by sulphation with SO2 and more...

Ashéninka y asháninka : ¿de cuántas lenguas hablamos?

NARCIS (Netherlands)

Pedrós, Caballero T.

2018-01-01

Este artículo intenta esclarecer cuántas lenguas hay en todo el complejo ashéninka-asháninka, en el cual el Ethnologue y el Glottolog distinguen siete o seis lenguas respectivamente, algo que resulta evidentemente erróneo cuando se estudia la escasa bibliografía existente de las distintas

Surface treated fly ash filled modified epoxy composites

Directory of Open Access Journals (Sweden)

Uma Dharmalingam

2015-01-01

Full Text Available Abstract Fly ash, an inorganic alumino silicate has been used as filler in epoxy matrix, but it reduces the mechanical properties due to its poor dispersion and interfacial bonding with the epoxy matrix. To improve its interfacial bonding with epoxy matrix, surface treatment of fly ash was done using surfactant sodium lauryl sulfate and silane coupling agent glycidoxy propyl trimethoxy silane. An attempt is also made to reduce the particle size of fly ash using high pressure pulverizer. To improve fly ash dispersion in epoxy matrix, the epoxy was modified by mixing with amine containing liquid silicone rubber (ACS. The effect of surface treated fly ash with varying filler loadings from 10 to 40% weight on the mechanical, morphological and thermal properties of modified epoxy composites was investigated. The surface treated fly ash was characterized by particle size analyzer and FTIR spectra. Morphological studies of surface treated fly ash filled modified epoxy composites indicate good dispersion of fillers in the modified epoxy matrix and improves its mechanical properties. Impact strength of the surface treated fly ash filled modified epoxy composites show more improvement than unmodified composites.

Geotechnical properties of ash deposits near Hilo, Hawaii

Science.gov (United States)

Wieczorek, G.F.; Jibson, R.W.; Wilson, R.C.; Buchanan-Banks, J. M.

1982-01-01

Two holes were hand augered and sampled in ash deposits near Hilo, Hawaii. Color, water content and sensitivity of the ash were measured in the field. The ash alternated between reddish brown and dark reddish brown in color and had water contents as high as 392%. A downhole vane shear device measured sensitivities as high as 6.9. A series of laboratory tests including grain size distribution, Atterberg limits, X-ray diffraction analysis, total carbon determination, vane shear, direct shear and triaxial tests were performed to determine the composition and geotechnical properties of the ash. The ash is very fine grained, highly plastic and composed mostly of gibbsite and amorphous material presumably allophane. The ash has a high angle of internal friction ranging from 40-43? and is classified as medium to very sensitive. A series of different ash layers was distinguished on the basis of plasticity and other geotechnical properties. Sensitivity may be due to a metastable fabric, cementation, leaching, high organic content, and thixotropy. The sensitivity of the volcanic ash deposits near Hilo is consistent with documented slope instability during earthquakes in Hawaii. The high angles of internal friction and cementation permit very steep slopes under static conditions. However, because of high sensitivity of the ash, these slopes are particularly susceptible to seismically-induced landsliding.

Emerald ash borer flight potential

Science.gov (United States)

Robin A. Taylor; Leah S. Bauer; Deborah L. Miller; Robert A. Haack

2005-01-01

The emerald ash borer (EAB), Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), is an invasive pest of ash trees (Fraxinus spp.) that is rapidly spreading from the probable introduction site in Detroit, Michigan. The rapid spread to areas outside Michigan is undoubtedly due to phoretic transport on nursery stock, logs, and...

Emerald ash borer biological control

Science.gov (United States)

Leah Bauer; Juli Gould; Jian Duan; Mike. Ulyshen

2011-01-01

Emerald ash borer (EAB) (Agrilus planipennis), an invasive buprestid from northeast Asia, was identified in 2002 as the cause of ash (Fraxinus) tree mortality in southeast Michigan and adjacent areas of Ontario, Canada. This destructive beetle apparently arrived in North America via infested solid wood packaging materials from...

Sensitization to cereals and peanut evidenced by skin prick test and specific IgE in food-tolerant, grass pollen allergic patients

DEFF Research Database (Denmark)

Martens, Maria; Schnoor, Heidi J; Malling, Hans-Jørgen

2011-01-01

The botanical relation between grass and cereal grains may be relevant when diagnosing food allergy to cereals. The aim was to investigate the diagnostic specificity of skin prick test (SPT) and specific immunoglobulin E (sIgE) tests to cereals and peanut in grass pollen allergic subjects without...

Volcanic Ash Data Assimilation System for Atmospheric Transport Model

Science.gov (United States)

Ishii, K.; Shimbori, T.; Sato, E.; Tokumoto, T.; Hayashi, Y.; Hashimoto, A.

2017-12-01

The Japan Meteorological Agency (JMA) has two operations for volcanic ash forecasts, which are Volcanic Ash Fall Forecast (VAFF) and Volcanic Ash Advisory (VAA). In these operations, the forecasts are calculated by atmospheric transport models including the advection process, the turbulent diffusion process, the gravitational fall process and the deposition process (wet/dry). The initial distribution of volcanic ash in the models is the most important but uncertain factor. In operations, the model of Suzuki (1983) with many empirical assumptions is adopted to the initial distribution. This adversely affects the reconstruction of actual eruption plumes.We are developing a volcanic ash data assimilation system using weather radars and meteorological satellite observation, in order to improve the initial distribution of the atmospheric transport models. Our data assimilation system is based on the three-dimensional variational data assimilation method (3D-Var). Analysis variables are ash concentration and size distribution parameters which are mutually independent. The radar observation is expected to provide three-dimensional parameters such as ash concentration and parameters of ash particle size distribution. On the other hand, the satellite observation is anticipated to provide two-dimensional parameters of ash clouds such as mass loading, top height and particle effective radius. In this study, we estimate the thickness of ash clouds using vertical wind shear of JMA numerical weather prediction, and apply for the volcanic ash data assimilation system.

Plutonium dissolution from Rocky Flats Plant incinerator ash

International Nuclear Information System (INIS)

Delegard, C.H.

1985-06-01

Rockwell Hanford Operations (Rockwell) soon will commence recovery of plutonium from Rocky Flats Plant incinerator ash. In preparation for this processing, Rockwell undertook literature and laboratory studies to identify, select and optimize plutonium dissolution methods for treating the ash. Ash reburning, followed by dissolution in nitric acid containing calcium fluoride, was selected as the processing method for the ash. Recommended values of process parameters were identified. Using the selected process, 99.5% plutonium recovery was achieved, leaving about 12.7 wt % heel residue for an equal weight composite of the three ashes tested. 15 refs., 26 figs

NEW TECHNOLOGY OF ASH AND SLAG CONCRETES

Directory of Open Access Journals (Sweden)

PAVLENKO T. M.

2017-03-01

Full Text Available Summary. Purpose. Development of scientific-technical bases of manufacture and application of concrete on the basis of ash and slag mixes of thermal power plants. Methods. It is proposed a new technology of preparation of ash and slag concrete mixes. First the ash and slag mix is dispersed through the sieve with meshes 5 mm in a fine-grained fraction and slag. Then, in accordance with the composition of the concrete, obtained fine-grained fraction, slag, cement and tempering water are separately dosed into the mixer. Results. It is proven the high efficiency of the proposed technology of manufacture of ash and slag concretes. It is established that this technological solution allows to increase the strength of concrete by 20...30%, and in the preparation of full-strength concrete to reduce the cement consumption by 15...20%. Scientific novelty. It is developed the new technology of ash and slag mixes application. The concrete mix on the basis of ash and slag mix has an optimal particle size distribution, which ensures the best compaction and, accordingly, the greatest strength of ash and slag concrete with the given cement consumption. Practical significance. The research results promote the mass application of ash and slag mixes of thermal power plants in construction, obtaining of products from the proposed concretes of low cost with high physical-mechanical properties. Conclusion. It is proven the high efficiency of the proposed technology of production of ash and slag concretes. It is established that this technological solution allows increasing concrete strength, and obtaining full-strength concrete to reduce cement consumption. The extensive application of such concrete in construction makes it possible to solve the problem of aggregates for concrete, promotes recycling of TPP waste and consequently the protection of the environment.

Fire severity effects on ash extractable Total Phosphorous

Science.gov (United States)

Pereira, Paulo; Úbeda, Xavier; Martin, Deborah

2010-05-01

Phosphorous (P) is a crucial element to plant nutrition and limits vegetal production. The amounts of P in soil are lower and great part of this nutrient is absorbed or precipitated. It is well known that fire has important implications on P cycle, that can be lost throughout volatilization, evacuated with the smoke, but also more available to transport after organic matter mineralization imposed by the fire. The release of P depends on ash pH and their chemical and physical characteristics. Fire temperatures impose different severities, according to the specie affected and contact time. Fire severity is often evaluated by ash colour and this is a low-cost and excellent methodology to assess the fire effects on ecosystems. The aim of this work is study the ash properties physical and chemical properties on ash extractable Total Phosphorous (TP), collected in three wildfires, occured in Portugal, (named, (1) Quinta do Conde, (2) Quinta da Areia and (3) Casal do Sapo) composed mainly by Quercus suber and Pinus pinaster trees. The ash colour was assessed using the Munsell color chart. From all three plots we analyzed a total of 102 ash samples and we identified 5 different ash colours, ordered in an increasing order of severity, Very Dark Brown, Black, Dark Grey, Very Dark Grey and Light Grey. In order to observe significant differences between extractable TP and ash colours, we applied an ANOVA One Way test, and considered the differences significant at a p<0.05. The results showed that significant differences in the extractable TP among the different ash colours. Hence, to identify specific differences between each ash colour, we applied a post-hoc Fisher LSD test, significant at a p<0.05. The results obtained showed significant differences between the extractable TP from Very dark Brown and Black ash, produced at lower severities, in relation to Dark Grey, Very Dark Grey and Light Grey ash, generated at higher severities. The means of the first group were higher

Electrodialytic removal of Cd from biomass combustion fly ash

DEFF Research Database (Denmark)

Pedersen, Anne Juul; Ottosen, Lisbeth M.; Simonsen, Peter

2004-01-01

Due to a high concentration of Cd, biomass combustion fly ash often fails to meet the Danish legislative requirements for recycling on agricultural fields. In this work the potential of using the method Electrodialytic Remediation to reduce the concentration of Cd in different biomass combustion....... The initial Cd concentration in the ashes varied between 8.8 mg Cd/kg DM (co-firing ash) and 64 mg Cd/kg DM (pre-washed straw ash), and pH varied from 3.7 to 13.3. In spite of large differences in ash characteristics, the electrodialytic remediation experiments indicated a good remediation potential for all...... four ashes. Final Cd concentrations below 2.0 mg Cd/kg were reached in all ashes within 14 days of remediation and legislative requirements were met. After further optimization of the remediation process on the pre-washed straw ash, limiting concentrations were reached after only 48 hours...

Granulated wood ash to forest soil - Ecological effects

International Nuclear Information System (INIS)

Rosen, K.; Eriksson, H.; Clarholm, M.; Lundkvist, H.; Rudebeck, A.

1993-01-01

This report describes research concerning ecological effects of wood ash recycling to forest soils. The main part of the minerals in the wood fuels are retained in the ashes after combustion. By returning the ashes back to the cleared forest areas, the mineral losses can be reduced. Adding ashes and limestone is a method to vitalize acidified forest soils and restore the production capacity. 48 refs, 26 figs, 8 tabs

Fundamental study of low-NOx combustion fly ash utilization

International Nuclear Information System (INIS)

Suuberg, Eric M.; Hurt, Robert H.

1998-01-01

This study is principally concerned with characterizing the organic part of coal combustion fly ashes. High carbon fly ashes are becoming more common as by-products of low-NOx combustion technology, and there is need to learn more about this fraction of the fly ash. The project team consists of two universities, Brown and Princeton, and an electrical utility, New England Power. A sample suite of over fifty fly ashes has been gathered from utilities across the United States, and includes ashes from a coals ranging in rank from bituminous to lignite. The characterizations of these ashes include standard tests (LOI, Foam Index), as well as more detailed characterizations of their surface areas, porosity, extractability and adsorption behavior. The ultimate goal is, by better characterizing the material, to enable broadening the range of applications for coal fly ash re-use beyond the current main market as a pozzolanic agent for concretes. The potential for high carbon-content fly ashes to substitute for activated carbons is receiving particular attention. The work performed to date has already revealed how very different the surfaces of different ashes produced by the same utility can be, with respect to polarity of the residual carbon. This can help explain the large variations in acceptability of these ashes as concrete additives

Can pore-clogging by ash explain post-fire runoff?

Science.gov (United States)

Stoof, Cathelijne R.; Gevaert, Anouk I.; Baver, Christine; Hassanpour, Bahareh; Morales, Veronica L.; Zhang, Wei; Martin, Deborah; Giri, Shree K.; Steenhuis, Tammo S.

2016-01-01

Ash plays an important role in controlling runoff and erosion processes after wildfire and has frequently been hypothesised to clog soil pores and reduce infiltration. Yet evidence for clogging is incomplete, as research has focussed on identifying the presence of ash in soil; the actual flow processes remain unknown. We conducted laboratory infiltration experiments coupled with microscope observations in pure sands, saturated hydraulic conductivity analysis, and interaction energy calculations, to test whether ash can clog pores (i.e. block pores such that infiltration is hampered and ponding occurs). Although results confirmed previous observations of ash washing into pores, clogging was not observed in the pure sands tested, nor were conditions found for which this does occur. Clogging by means of strong attachment of ash to sand was deemed unlikely given the negative surface charge of the two materials. Ponding due to washing in of ash was also considered improbable given the high saturated conductivity of pure ash and ash–sand mixtures. This first mechanistic step towards analysing ash transport and attachment processes in field soils therefore suggests that pore clogging by ash is unlikely to occur in sands. Discussion is provided on other mechanisms by which ash can affect post-fire hydrology.

Reduction of metal leaching in brown coal fly ash using geopolymers

International Nuclear Information System (INIS)

Bankowski, P.; Zou, L.; Hodges, R.

2004-01-01

Current regulations classify fly ash as a prescribed waste and prohibit its disposal in regular landfill. Treatment of the fly ash can reduce the leach rate of metals, and allow it to be disposed in less prescribed landfill. A geopolymer matrix was investigated as a potential stabilisation method for brown coal fly ash. Precipitator fly ash was obtained from electrostatic precipitators and leached fly ash was collected from ash disposal ponds, and leaching tests were conducted on both types of geopolymer stabilised fly ashes. The ratio of fly ash to geopolymer was varied to determine the effects of different compositions on leaching rates. Fourteen metals and heavy metals were targeted during the leaching tests and the results indicate that a geopolymer is effective at reducing the leach rates of many metals from the fly ash, such as calcium, arsenic, selenium, strontium and barium. The major element leachate concentrations obtained from leached fly ash were in general lower than that of precipitator fly ash. Conversely, heavy metal leachate concentrations were lower in precipitator fly ash than leached pond fly ash. The maximum addition of fly ash to this geopolymer was found to be 60 wt% for fly ash obtained from the electrostatic precipitators and 70 wt% for fly ash obtained from ash disposal ponds. The formation of geopolymer in the presence of fly ash was studied using 29Si MAS-NMR and showed that a geopolymer matrix was formed. X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM) imaging showed the interaction of the fly ash with the geopolymer, which was related to the leachate data and also the maximum percentage fly ash addition

Use of ash in the fertilisation of peatland forests

International Nuclear Information System (INIS)

Moilanen, M.; Korpilahti, A.

2000-01-01

About 100,000 tonnes of bark and other wood-based ash are produced annually by the forest industries and heating plants in Finland. This amount would be sufficient for fertilising about 25,000 hectares of forest. When applied to peatland forests, this would produce extra forest growth of about 75,000 m 3 per a year. When considering the objectives of forestry, the practical benefits and economic profitability of ash fertilisation are at their peak on peatlands rich in nitrogen. Wood ash induces added tree growth (measured in terms of stemwood) in pine stands on herb- and sedge-rich parklands within 2-3 years of application. On nitrogen-deficient dwarf-shrub and Sphagnum-rich peatlands this growth reaction manifests itself only after 7-8 years have passed and even then at a considerably lower level. The application of mere ash does not result in notable increases in tree growth on upland forest sites. However, ash does change the growth conditions by reducing the acidity of the soil and by accelerating microbial decomposition. The phosphorus contained in ash has not been observed to have been leached into drainage waters on drained sites, at least not during the first two years after application, provided that care has been practised when spreading ash. However, the movement of readily-soluble nutrients has been observed and more so on nutrient-poor sites than on nutrient-rich sites. Although the suitability of ash as fertiliser in peatland forests has been recognised on the basis of long-term ash trials established at the Finnish Forest Research Institute, ash fertilisation has not been carried out made on a practical scale mainly because of the dust problem when spreading it. The purpose of pretreatment with ash is first and foremost to transform the ash into sufficiently dust-free form to enable it to be spread readily. An added advantage is that pelletised ash causes a lesser pH shock to plank than ash in dust form. (orig.)

New Umami Amides: Structure-Taste Relationship Studies of Cinnamic Acid Derived Amides and the Natural Occurrence of an Intense Umami Amide in Zanthoxylum piperitum.

Science.gov (United States)

Frerot, Eric; Neirynck, Nathalie; Cayeux, Isabelle; Yuan, Yoyo Hui-Juan; Yuan, Yong-Ming

2015-08-19

A series of aromatic amides were synthesized from various acids and amines selected from naturally occurring structural frameworks. These synthetic amides were evaluated for umami taste in comparison with monosodium glutamate. The effect of the substitution pattern of both the acid and the amine parts on umami taste was investigated. The only intensely umami-tasting amides were those made from 3,4-dimethoxycinnamic acid. The amine part was more tolerant to structural changes. Amides bearing an alkyl- or alkoxy-substituted phenylethylamine residue displayed a clean umami taste as 20 ppm solutions in water. Ultraperformance liquid chromatography coupled with a high quadrupole-Orbitrap mass spectrometer (UPLC/MS) was subsequently used to show the natural occurrence of these amides. (E)-3-(3,4-Dimethoxyphenyl)-N-(4-methoxyphenethyl)acrylamide was shown to occur in the roots and stems of Zanthoxylum piperitum, a plant of the family Rutaceae growing in Korea, Japan, and China.

The relation between pre-eruptive bubble size distribution, ash particle morphology, and their internal density: Implications to volcanic ash transport and dispersion models

Science.gov (United States)

Proussevitch, Alexander

2014-05-01

Parameterization of volcanic ash transport and dispersion (VATD) models strongly depends on particle morphology and their internal properties. Shape of ash particles affects terminal fall velocities (TFV) and, mostly, dispersion. Internal density combined with particle size has a very strong impact on TFV and ultimately on the rate of ash cloud thinning and particle sedimentation on the ground. Unlike other parameters, internal particle density cannot be measured directly because of the micron scale sizes of fine ash particles, but we demonstrate that it varies greatly depending on the particle size. Small simple type ash particles (fragments of bubble walls, 5-20 micron size) do not contain whole large magmatic bubbles inside and their internal density is almost the same as that of volcanic glass matrix. On the other side, the larger compound type ash particles (>40 microns for silicic fine ashes) always contain some bubbles or the whole spectra of bubble size distribution (BSD), i.e. bubbles of all sizes, bringing their internal density down as compared to simple ash. So, density of the larger ash particles is a function of the void fraction inside them (magmatic bubbles) which, in turn, is controlled by BSD. Volcanic ash is a product of the fragmentation of magmatic foam formed by pre-eruptive bubble population and characterized by BSD. The latter can now be measured from bubble imprints on ash particle surfaces using stereo-scanning electron microscopy (SSEM) and BubbleMaker software developed at UNH, or using traditional high-resolution X-Ray tomography. In this work we present the mathematical and statistical formulation for this problem connecting internal ash density with particle size and BSD, and demonstrate how the TFV of the ash population is affected by variation of particle density.

High temperature co-treatment of bottom ash and stabilized fly ashes from waste incineration

DEFF Research Database (Denmark)

Sørensen, Mette Abildgaard; Mogensen, E.P.B.; Lundtorp, Kasper

2001-01-01

Bottom ashes from two Danish municipal solid waste incineration plants were heated at 900 degreesC with iron oxide stabilized air pollution control residues at actual mass flow ratios (9:1), simulating a treating method for the residues. The two residues were cotreated, producing one combined...... ashes. The process, thus, fixates the metals in the solid residues without altering the leaching properties of the bottom ash too significantly. (C) 2001 Elsevier Science Ltd. All rights reserved....... stream that may be utilized as a secondary road construction material. Scanning electron microscope analysis and grain size distribution analysis indicated that sintering of the particles did not occur. Batch leaching tests at liquid/solid 10 I/kg at a range of pH-values (6-10) quantified with respect...

Potential for thermochemical conversion of biomass residues from the integrated sugar-ethanol process - Fate of ash and ash-forming elements.

Science.gov (United States)

Dirbeba, Meheretu Jaleta; Brink, Anders; DeMartini, Nikolai; Zevenhoven, Maria; Hupa, Mikko

2017-06-01

In this work, potential for thermochemical conversion of biomass residues from an integrated sugar-ethanol process and the fate of ash and ash-forming elements in the process are presented. Ash, ash-forming elements, and energy flows in the process were determined using mass balances and analyses of eight different biomass samples for ash contents, elemental compositions, and heating values. The results show that the ash content increases from the sugarcane to the final residue, vinasse. The cane straw, which is left in the field, contains one-third of the energy and 25% of the K and Cl while the vinasse contains 2% of the energy and 40% of the K and Cl in the cane. K and Cl in biomass fuels cause corrosion and fouling problems in boilers and gasifiers. Over 85% of these elements in the straw are water soluble indicating that water leaching would improve it for utilization in thermochemical conversion. Copyright © 2017 Elsevier Ltd. All rights reserved.

Ash content of lignites - radiometric analysis

International Nuclear Information System (INIS)

Leonhardt, J.; Thuemmel, H.W.

1986-01-01

The quality of lignites is governed by the ash content varying in dependence upon the geologic conditions. Setup and function of the radiometric devices being used for ash content analysis in the GDR are briefly described

Adhesion Strength of Biomass Ash Deposits

DEFF Research Database (Denmark)

Laxminarayan, Yashasvi; Jensen, Peter Arendt; Wu, Hao

2015-01-01

This study investigates the shear adhesion strength of biomass ash deposits on superheater tubes. Artificial biomass ash deposits were prepared on superheater tubes and sintered in an oven at temperatures up to 1000°C. Subsequently, the deposits were sheared off with the help of an electrically...... controlled arm. Higher sintering temperatures resulted in greater adhesion strengths, with a sharp increase observed near the melting point of the ash. Repetition of experiments with fixed operation conditions revealed considerable variation in the obtained adhesion strengths, portraying the stochastic...

The antiplasmodium effects of a traditional South American remedy: Zanthoxylum chiloperone var. angustifolium against chloroquine resistant and chloroquine sensitive strains of Plasmodium falciparum

Directory of Open Access Journals (Sweden)

Gerardo Cebrian-Torrejon

2011-06-01

Full Text Available Zanthoxylum chiloperone var. angustifolium Engl., Rutaceae, is used in traditional medicine to treat fungal and protozoal infections in the central area of South America. Considering the increasing resistance of Plasmodium falciparum in malarial ridden areas, we explored the anti-plasmodial effects of three compounds isolated from Z. chiloperone. The pyranocoumarin transavicennol and the canthinone alkaloids, canthin-6-one and 5-methoxycanthin-6-one, were found to have IC50 on chloroquine/mefloquine resistant and sensitive strains of P. falciparum of 0.5-2.7, 2.0-5.3 and 5.1-10.4 ƒÊg/mL, respectively. Moreover, the formation of heme adducts by these compounds is described by a novel alternative method based on MS-CID methods. The alkylamide sanshool was also identified, for first time in this plant, in the dichloromethanic and ethanolic extracts and the extracts were found to be notably non-toxic and displayed good anti-plasmodial effects.

Monitoring ash (Fraxinus spp.) decline and emerald ash borer (Agrilus planipennis) symptoms in infested areas

Science.gov (United States)

Kathleen S. Knight; Britton P. Flash; Rachel H. Kappler; Joel A. Throckmorton; Bernadette Grafton; Charles E. Flower

2014-01-01

Emerald ash borer (A. planipennis) (EAB) has had a devastating effect on ash (Fraxinus) species since its introduction to North America and has resulted in altered ecological processes across the area of infestation. Monitoring is an important tool for understanding and managing the impact of this threat, and the use of common...

Environmentally friendly use of non-coal ashes in Sweden.

Science.gov (United States)

Ribbing, C

2007-01-01

The Swedish Thermal Engineering Research Institute (Värmeforsk) initiated an applied research program "Environmentally friendly use of non-coal ashes", in 2002. The program aims at increasing knowledge on the by-products of energy production and their application. The goal of formulating technical and environmental guidelines and assessments is a major point of the program, which is supported by about forty authorities and private organisations. The programme has been divided into four areas: recycling of ashes to forests, geotechnical applications, use in landfilling, and environmental aspects and chemistry. Among all results obtained, the following progress is shown: *Evidence for the positive effects of spreading ashes on forest growth. *A proposal for environmental guidelines on the utilisation of ashes in construction. *A handbook for using non-coal fly ashes in unpaved roads. *Technical and environmental assessments of MSWI bottom ashes in road construction. *Development of the use of ashes with municipal wastewater sludge as a cover for landfills and mine tailings. *Use of ashes from bio-fuels in concrete and replacement of cement in stoop mining. *A method to classify those by-products from combustion that have mirror entries in the EWC as a hazardous or non-hazardous compound. The Ash Programme has also made it possible to increase knowledge on ashes as valuable materials, on quality assurance and on markets for recovered materials.

Advanced characterisation of municipal solid waste ashes

Energy Technology Data Exchange (ETDEWEB)

Skytte Pedersen, Randi

2002-12-15

This report deals with characterisation of Municipal Solid Waste (MSW) ashes from the Danish power plant Maebjergvaerket, Holstebro. MSW has been used as a fuel since the mid 1960's and since then, the MSW incineration plants have experienced operational problems due to deposit formation and corrosion. Inorganic elements tightly or loosely bound in the waste are the main cause of these problems. The tightly bound elements will mainly stay on the grate during combustion, whereas the loosely bound elements are volatilised and recondensed elsewhere in the furnace. Many of the heavy metals form volatile chlorides during the incineration, and the fly ash fraction thus show enrichment in these elements. Presence of chlorides and heavy metals in deposits may cause severe corrosion due to formation of low-melting eutectics. Chlorine gas in the flue gas is also of major concern with respect to corrosion, due to formation of volatile chlorides when chlorine comes in contact with the tube material. Four different ash fractions (bottom ash, super heater ash, economiser ash and fly ash) taken from Maebjergvaerket have been analysed with respect to particle sizes, structures, shapes and composition. The applied methods were scanning electron microscopy (SEM), energy dispersive X-ray analyses (EDX) and mapping, which were used in order to determine sizes, chemical composition and structure of the particles. X-ray powder diffraction (XRD) was used to provide information about crystallography and mineral phases. Chemical analysis was also performed along with a particle size distribution for the fine-grained fractions (economiser and fly ash). The amount of silicates consisting of Ca, Al and Si, were found to decrease through the furnace, whereas the amount of alkali (Na, K) chlorides and heavy metals (Pb, Zn) increased. The bonding in the waste before incineration is the direct cause of this, since silicates are tightly bound and chlorides are loosely bound. There was a

Solidification of radioactive incinerator ash

International Nuclear Information System (INIS)

Schuler, T.F.; Charlesworth, D.L.

1986-01-01

The Ashcrete process will solidify ash generated by the Beta Gamma Incinerator (BGI) at the Savannah River Plant (SRP). The system remotely handles, adds material to, and tumbles drums of ash to produce ashcrete, a stabilized wasteform. Full-scale testing of the Ashcrete unit began at Savannah River Laboratory (SRL) in January 1984, using nonradioactive ash. Tests determined product homogeneity, temperature distribution, compressive strength, and final product formulation. Product formulations that yielded good mix homogeneity and final product compressive strength were developed. Drum pressurization and temperature rise (resulting from the cement's heat of hydration) were also studied to verify safe storage and handling characteristics. In addition to these tests, an expert system was developed to assist process troubleshooting

Use of wood ash for road stabilisation

International Nuclear Information System (INIS)

Lagerkvist, A.; Lind, B.

2009-01-01

Due to warmer winters in Sweden, the bearing capacity of forestry roads has become increasingly problematic in recent years. Road stabilization is needed in order to get timber out from the forests. This usually involves the addition of cement to the road body. However, wood ash is a possible substitute for cement because it has similar properties. Using wood ash has the added advantage of saving landfill space. This paper presented an ongoing laboratory study on leaching and mechanical stability, as well as frost-sensitivity using a 30 per cent ash addition to natural soils for reinforcing a forestry road near Timra in central Sweden. The road was being monitored with regard to environmental impact and mechanical properties. The paper discussed the potential of biofuel ashes and the increasing need to reinforce infrastructure due to climate change. The environmental impact from ash use in road constructions was then addressed. It was concluded that the application of ash in road construction would help to strengthen forest roads, make them more resistant to climatic change and render them accessible year-round. 32 refs., 3 tabs., 2 figs.

A robust method to forecast volcanic ash clouds

Science.gov (United States)

Denlinger, Roger P.; Pavolonis, Mike; Sieglaff, Justin

2012-01-01

Ash clouds emanating from volcanic eruption columns often form trails of ash extending thousands of kilometers through the Earth's atmosphere, disrupting air traffic and posing a significant hazard to air travel. To mitigate such hazards, the community charged with reducing flight risk must accurately assess risk of ash ingestion for any flight path and provide robust forecasts of volcanic ash dispersal. In response to this need, a number of different transport models have been developed for this purpose and applied to recent eruptions, providing a means to assess uncertainty in forecasts. Here we provide a framework for optimal forecasts and their uncertainties given any model and any observational data. This involves random sampling of the probability distributions of input (source) parameters to a transport model and iteratively running the model with different inputs, each time assessing the predictions that the model makes about ash dispersal by direct comparison with satellite data. The results of these comparisons are embodied in a likelihood function whose maximum corresponds to the minimum misfit between model output and observations. Bayes theorem is then used to determine a normalized posterior probability distribution and from that a forecast of future uncertainty in ash dispersal. The nature of ash clouds in heterogeneous wind fields creates a strong maximum likelihood estimate in which most of the probability is localized to narrow ranges of model source parameters. This property is used here to accelerate probability assessment, producing a method to rapidly generate a prediction of future ash concentrations and their distribution based upon assimilation of satellite data as well as model and data uncertainties. Applying this method to the recent eruption of Eyjafjallajökull in Iceland, we show that the 3 and 6 h forecasts of ash cloud location probability encompassed the location of observed satellite-determined ash cloud loads, providing an

Insecticidal Activities of Bark, Leaf and Seed Extracts of Zanthoxylum heitzii against the African Malaria Vector Anopheles gambiae

Directory of Open Access Journals (Sweden)

Hans J. Overgaard

2014-12-01

Full Text Available The olon tree, Zanthoxylum heitzii (syn. Fagara heitzii is commonly found in the central-west African forests. In the Republic of Congo (Congo-Brazzaville its bark is anecdotally reported to provide human protection against fleas. Here we assess the insecticidal activities of Z. heitzii stem bark, seed and leaf extracts against Anopheles gambiae s.s, the main malaria vector in Africa. Extracts were obtained by Accelerated Solvent Extraction (ASE using solvents of different polarity and by classical Soxhlet extraction using hexane as solvent. The insecticidal effects of the crude extracts were evaluated using topical applications of insecticides on mosquitoes of a susceptible reference strain (Kisumu [Kis], a strain homozygous for the L1014F kdr mutation (kdrKis, and a strain homozygous for the G119S Ace1R allele (AcerKis. The insecticidal activities were measured using LD50 and LD95 and active extracts were characterized by NMR spectroscopy and HPLC chromatography. Results show that the ASE hexane stem bark extract was the most effective compound against An. gambiae (LD50 = 102 ng/mg female, but was not as effective as common synthetic insecticides. Overall, there was no significant difference between the responses of the three mosquito strains to Z. heitzii extracts, indicating no cross resistance with conventional pesticides.

Bacillus endozanthoxylicus sp. nov., an endophytic bacterium isolated from Zanthoxylum bungeanum Maxim leaves.

Science.gov (United States)

Ma, Li; Xi, Jia-Qin; Cao, Yong-Hong; Wang, Xiao-Yan; Zheng, Shuai-Chao; Yang, Cheng-Gang; Yang, Ling-Ling; Mi, Qi-Li; Li, Xue-Mei; Zhu, Ming-Liang; Mo, Ming-He

2017-10-01

A Gram-stain-positive, rod-shaped, motile bacterium, designated as 1404 T , was isolated from leaves of Chinese red pepper (Huajiao) (Zanthoxylum bungeanum Maxim) collected from Gansu, north-west China. Spores were not observed under a range of conditions. Strain 1404 T was observed to grow at 15-45 °C and pH 6.0-10.0 and in presence of 0-5 % (w/v) NaCl concentration. The cell wall of strain 1404 T was found to contain meso-diaminopimelic acid, and the predominant respiratory quinone was identified as MK-7. The major polar lipids were diphosphatidylglycerol, phosphatidylglycerol, phosphatidylethanolamine and an unidentified phospholipid as well as three unidentified polar lipids. The major fatty acids profile of strain 1404 T consisted of iso-C15 : 0 (25.6 %), anteiso-C15 : 0 (18.4 %) and iso-C14 : 0 (12.1 %). Phylogenetic analysis based on 16S rRNA gene sequences indicated that strain 1404 T was affiliated to the genus Bacillus and was closely related to Bacillusoryzisoli 1DS3-10 T , Bacillusbenzoevorans DSM 5391 T and Bacilluscirculans DSM 11 T with sequence similarity of 98.3, 98.2 and 96.9 %, respectively. The G+C content of the genomic DNA was determined to be 39.4 mol%. DNA-DNA hybridization values indicated that relatedness between strain 1404 T and the type strains of closely related species of the genus Bacillus was below 41 %. Therefore, on the basis of the data from the polyphasic taxonomic study presented, strain 1404 T represents a novel species of the genus Bacillus, for which the name proposed is Bacillus endozanthoxylicus sp. nov. The type strain is 1404 T (=CCTCC AB 2017021 T =KCTC 33827 T ).

Acidolysis of coal fly ash by Aspergillus niger

Energy Technology Data Exchange (ETDEWEB)

Torma, A.E.; Singh, A.K. (EG and G Idaho Inc., Idaho Falls, ID (United States). Center for Biological Processing Technology)

1993-12-01

The kinetics of aluminium extraction were investigated, using as-received and calcined fly ash samples and a pure culture of [ital Aspergillus niger]. This fungus metabolized sucrose to citric and oxalic acids, which were involved in the acidolysis of fly ash. Aluminium extraction from as-received fly ash was only 5-8%, whereas from calcined fly ash it was up to 93.5%. The order of reaction and the overall reaction rate constant were determined by the van't Hoff technique with respect to the concentration of calcined fly ash. A linearized form of a modified Monod expression was applied to the experimental data to assess the kinetic constants for the acidolysis process. Statistically designed experiments were carried out with calcined fly ash and synthetic solutions containing citric and oxalic acids to determine the optimum leaching conditions. The acidolysis reaction mechanism is discussed. 28 refs., 6 figs., 3 tabs.

Ge extraction from gasification fly ash

Energy Technology Data Exchange (ETDEWEB)

Oriol Font; Xavier Querol; Angel Lopez-Soler; Jose M. Chimenos; Ana I. Fernandez; Silvia Burgos; Francisco Garcia Pena [Institute of Earth Sciences ' Jaume Almera' , Barcelona (Spain)

2005-08-01

Water-soluble germanium species (GeS{sub 2}, GeS and hexagonal-GeO{sub 2}) are generated during coal gasification and retained in fly ash. This fact together with the high market value of this element and the relatively high contents in the fly ashes of the Puertollano Integrated Gasification in Combined Cycle (IGCC) plant directed our research towards the development of an extraction process for this element. Major objectives of this research was to find a low cost and environmentally suitable process. Several water based extraction tests were carried out using different Puertollano IGCC fly ash samples, under different temperatures, water/fly ash ratios, and extraction times. High Ge extraction yields (up to 84%) were obtained at room temperature (25{sup o}C) but also high proportions of other trace elements (impurities) were simultaneously extracted. Increasing the extraction temperature to 50, 90 and 150{sup o}C, Ge extraction yields were kept at similar levels, while reducing the content of impurities, the water/fly ash ratio and extraction time. The experimental data point out the influence of chloride, calcium and sulphide dissolutions on the Ge extraction. 16 refs., 9 figs., 6 tabs.

Coal ash usage in environmental restoration at the Hanford site

Energy Technology Data Exchange (ETDEWEB)

Scanlon, P.L.; Sonnichsen, J.C.; Phillips, S.J.

1994-08-01

The ash stockpiled next to the 284E steam plant is mixed fly ash, bottom ash, and slag. The ash consists of (1) baghouse residue and (2) a mixture of bottom ash and slag which is washed out of the bottom of the boilers daily. In 1991, a Toxicity Characteristic Leaching Procedure (TCLP) was performed on several samples of this ash (Hazen Research 1991). This procedure is designed to determine the mobility of organic and inorganic anatytes present in liquid, solid, or multiphasic wastes (EPA 1994). The ash tested came from surge bins, conveyor samples, and bottom ash and fly ash from the boilers at 284E. Antimony, cadmium, germanium, molybdenum, silver, thallium, tungsten, and vanadium were tested for, but on all samples were below detection Limits for the testing method. Analytes present in relatively high concentrations (but less than one part per thousand) included barium, boron, chromium, fluorine, and zinc. The size of ash particles passing through a Taylor sieve series was very evenly distributed from 1 to 200m.

Engineering properties of lightweight geopolymer synthesized from coal bottom ash and rice husk ash

Science.gov (United States)

Thang, Nguyen Hoc; Hoa, Nguyen Ngoc; Quyen, Pham Vo Thi Ha; Tuyen, Nguyen Ngoc Kim; Anh, Tran Vu Thao; Kien, Pham Trung

2018-04-01

Geopolymer technology was developed by Joseph Davidovits in 1970s based on reactions among alumino-silicate resources in high alkaline conditions. Geopolymer has been recently gaining attention as an alternative binder for Ordinary Portland cement (OPC) due to its low energy and CO2 burden. The raw materials used for geopolymerization normally contain high SiO2 and Al2O3 in the chemical compositions such as meta-kaoline, rice husk ash, fly ash, bottom ash, blast furnace slag, red mud, and others. Moreover, in this paper, coal bottom ash (CBA) and rice husk ash (RHA), which are industrial and agricultural wastes, respectively, were used as raw materials with high alumino-silicate resources. Both CBA and RHA were mixed with sodium hydroxide (NaOH) solution for 20 minutes to obtain the geopolymer pastes. The pastes were filled in 5-cm cube molds according to ASTM C109/C109M 99, and then cured at room condition for hardening of the geopolymer specimens. After 24 hours, the specimens were removed out of the molds and continuously cured at room condition for 27 days. The geopolymer-based materials were then tested for engineering properties such as compressive strength (MPa), volumetric weight (kg/m3), and water absorption (kg/m3). Results indicated that the material can be considered lightweight with volumetric weight from 1192 to 1425 kg/m3; compressive strength at 28 days is in the range of 12.38 to 37.41 MPa; and water absorption is under 189.92 kg/m3.

Greener management practices - ash mound reclamation

Energy Technology Data Exchange (ETDEWEB)

Kapur, S.L.; Shyam, A.K.; Soni, R. [National Thermal Power Corp. Ltd., New Delhi (India)

2002-12-01

The dry ash handling system at Dadri has been pioneered for the first time in India by the National Thermal Power Corporation (NTPC). The system is similar to that at the Drax power station in England. The paper reports the successful experimental trials carried out on vegetation of temporary ash mounds to assess the growth potential of local herbs, shrubs, trees and grasses directly on ash with no soil cover or fertiliser. These were extended to trials directly on the available (completed) mound surfaces. The grass Cynodon dactylon germinated well as did seeds of tree species including the Casurarina and Eucalyptus. It is hoped that efforts at Dadri will ultimately transform the ash into a productive and self sustaining ecosystem, as leaf fall adds additional organic material and the weathering process continues. 6 refs., 6 figs.

Column leaching from biomass combustion ashes

DEFF Research Database (Denmark)

Maresca, Alberto; Astrup, Thomas Fruergaard

2015-01-01

The utilization of biomass combustion ashes for forest soil liming and fertilizing has been addressed in literature. Though, a deep understanding of the ash chemical composition and leaching behavior is necessary to predict potential benefits and environmental risks related to this practice....... In this study, a fly ash sample from an operating Danish power plant based on wood biomass was collected, chemically characterized and investigated for its leaching release of nutrients and heavy metals. A column leaching test was employed. The strongly alkaline pH of all the collected eluates suggested...

Clay formation and metal fixation during weathering of coal fly ash

International Nuclear Information System (INIS)

Zevenbergen, C.; Bradley, J.P.; Reeuwijk, L.P. Van; Shyam, A.K.; Hjelmar, O.; Comans, R.N.J.

1999-01-01

The enormous and worldwide production of coal fly ash cannot be durably isolated from the weathering cycle, and the weathering characteristics of fly ash must be known to understand the long-term environmental impact. The authors studied the weathering of two coal fly ashes and compared them with published data from weathered volcanic ash, it's closest natural analogue. Both types of ash contain abundant aluminosilicate glass, which alters to noncrystalline clay. However, this study reveals that the kinetics of coal fly ash weathering are more rapid than those of volcanic ash because the higher pH of fresh coal fly ash promotes rapid dissolution of the glass. After about 10 years of weathering, the noncrystalline clay content of coal fly ash is higher than that of 250-year-old volcanic ash. The observed rapid clay formation together with heavy metal fixation imply that the long-term environmental impact of coal fly ash disposal may be less severe and the benefits more pronounced than predicted from previous studies on unweathered ash. Their findings suggest that isolating coal fly ash from the weathering cycle may be counterproductive because, in the long-term under conditions of free drainage, fly ash is converted into fertile soil capable of supporting agriculture

Simulated Impacts of Emerald Ash Borer on Throughfall and Stemflow Inputs of Water and Nitrogen in Black Ash Wetlands in Northern Michigan

Science.gov (United States)

Pypker, T. G.; Davis, J.; Van Grinsven, M. J.; Bolton, N. W.; Shannon, J.; Kolka, R. K.; Nelson, J.; Wagenbrenner, J. W.

2014-12-01

Emerald ash borer (Agrilus planipennis Fairmaire (EAB)) is an invasive insect that effectively kills ash trees (genus: Fraxinus) greater than 2.5 cm in diameter, resulting in near-complete stand mortality within 3-4 years. Black ash wetlands occupy approximately 270,000 ha in Michigan, and have 40 to 90% of the basal area occupied by black ash (F. nigra Marshall); hence the loss of black ash may result in dramatic changes in the canopy hydrology and nutrient deposition. We assessed the impact of a simulated EAB invasion on throughfall and stemflow quantity and nitrogen (N) content in 9 uninfected black ash wetlands located in the Upper Peninsula of Michigan. Within the 9 stands, 3 stands were left untreated ('Control'), 3 stands had all the black ash trees manually girdled ('Girdled') and 3 had all the black ash trees felled by chainsaw ('Clearcut'). We measured the quantity and inorganic-N content of throughfall using an array of randomly placed collectors (n = 16 per site). Stemflow was monitored at 2 sites (n = 12 trees) on the 3 most common tree species (black ash, yellow birch (Betula alleghaniensis Britt.) and red maple (Acer rubra L.)). Preliminary results indicate that relative to the Control, average monthly throughfall was 25% and 1% greater in the Clearcut and Girdled sites, respectively. While the loss of the ash trees resulted in greater throughfall inputs in the Clearcut sites, water table heights did not significantly change as a result of the treatments. Stemflow from live black ash trees was lower than from the yellow birch and red maple trees. As a result, we predict stemflow will increase over time as species with smoother bark and less upright branching begin replacing the black ash. Hence, the change in tree species may result in a greater concentration of inorganic-N inputs to the base of the trees, thereby altering the distribution of inorganic-N inputs into the wetland. Our preliminary results show no significant change in the total

Possibilities of municipal solid waste incinerator fly ash utilisation.

Science.gov (United States)

Hartmann, Silvie; Koval, Lukáš; Škrobánková, Hana; Matýsek, Dalibor; Winter, Franz; Purgar, Amon

2015-08-01

Properties of the waste treatment residual fly ash generated from municipal solid waste incinerator fly ash were investigated in this study. Six different mortar blends with the addition of the municipal solid waste incinerator fly ash were evaluated. The Portland cement replacement levels of the municipal solid waste incinerator fly ash used were 25%, 30% and 50%. Both, raw and washed municipal solid waste incinerator fly ash samples were examined. According to the mineralogical composition measurements, a 22.6% increase in the pozzolanic/hydraulic properties was observed for the washed municipal solid waste incinerator fly ash sample. The maximum replacement level of 25% for the washed municipal solid waste incinerator fly ash in mortar blends was established in order to preserve the compressive strength properties. Moreover, the leaching characteristics of the crushed mortar blend was analysed in order to examine the immobilisation of its hazardous contents. © The Author(s) 2015.

Optimization of heat-liberating batches for ash residue stabilization

International Nuclear Information System (INIS)

Karlina, O.K.; Varlackova, G.A.; Ojovan, M.I.; Tivansky, V.M.; Dmitriev, S.A.

1999-01-01

The ash residue obtained after incineration of solid radioactive waste is a dusting poly-dispersed powder like material that contains radioactive nuclides ( 137 Cs, 90 Sr, 239 Pu, hor ( ellipsis)). Specific radioactivity of the ash can be about 10 5 --10 7 Bq/kg. In order to dispose of the ash, residue shall be stabilized by producing a monolith material. The ash residue can be either vitrified or stabilized into a ceramic matrix. For this purpose the ash residue is mixed with fluxing agents followed by melting of obtained composition in the different type melters. As a rule this requires both significant energy consumption and complex melting equipment. A stabilization technology of ash residue was proposed recently by using heat liberating batches-compositions with redox properties. The ash residue is melted due to exothermic chemical reactions in the mixture with heat-liberating batch that occur with considerable release of heat. Stabilization method has three stages: (1) preparation of a mixture of heating batch and ash residue with or without glass forming batch (frit); (2) ignition and combustion of mixed composition; (3) cooling (quenching) of obtained vitreous material. Combustion of mixed composition occurs in the form of propagation of reacting wave. The heat released during exothermic chemical reactions provides melting of ash residue components and production of glass-like phase. The final product consists of a glass like matrix with embedded crystalline inclusions of infusible ash residue components

STRATEGIES AND TECHNOLOGY FOR MANAGING HIGH-CARBON ASH

Energy Technology Data Exchange (ETDEWEB)

Robert Hurt; Eric Suuberg; John Veranth; Xu Chen; Indrek Kulaots

2004-02-13

The overall objective of the present project was to identify and assess strategies and solutions for the management of industry problems related to carbon in ash. Specific issues addressed included: (1) the effect of parent fuel selection on ash properties and adsorptivity, including a first ever examination of the air entrainment behavior of ashes from alternative (non-coal) fuels; (2) the effect of various low-NOx firing modes on ash properties and adsorptivity based on pilot-plant studies; and (3) the kinetics and mechanism of ash ozonation. This laboratory data has provided scientific and engineering support and underpinning for parallel process development activities. The development work on the ash ozonation process has now transitioned into a scale-up and commercialization project involving a multi-industry team and scheduled to begin in 2004. This report describes and documents the laboratory and pilot-scale work in the above three areas done at Brown University and the University of Utah during this three-year project.

Insecticidal Constituents of Essential Oil Derived from Zanthoxylum armatum against Two Stored-Product Insects.

Science.gov (United States)

Wang, Cheng-Fang; Zhang, Wen-Juan; You, Chun-Xue; Guo, Shan-Shan; Geng, Zhu-Feng; Fan, Li; Du, Shu-Shan; Deng, Zhi-Wei; Wang, Yong-Yan

2015-01-01

In the course of our search for natural bioactive chemicals and investigations on their insecticidal activities from some medicinal plants growing in China, the essential oil derived from the twigs of Zanthoxylum armatum (Rutaceae) was found to possess strong insecticidal activities against two stored-product insects, Lasioderma serricorne and Tribolium castaneum. A total of 32 constituents of the essential oil were identified by GC and GC-MS analysis, and it revealed (E)-anethole (20.5%), 1,8-cineole (14.0%), 2-tridecanone (12.5%), limonene (9.0%) and piperitone (8.0%) as major components, followed by β-phellandrene (6.3%), β-pinene (5.1%) and 4-terpineol (4.4%). From the essential oil, five compounds were isolated and identified as (E)-anethole, 1,8-cineole, 2-tridecanone, limonene and piperitone. The results of insecticidal bioassays showed that the essential oil of Z. armatum exhibited strong fumigant toxicity towards L. serricorne and T. castaneum with LC50 values of 13.83 and 4.28 mg/L air, respectively, and also possessed contact toxicity against two insect species with LD50 values of 18.74 and 32.16 μg/adult, respectively. Among the active compounds, piperitone performed the strongest fumigant toxicity against L. serricorne (LC50 = 1.21 mg/L air) and contact toxicity against T. castaneum (LD50 = 3.16 μg/adult). 1,8-Cineole, limonene and piperitone showed similar fumigant toxicity against T. castaneum with LC50 values of 5.47, 6.21 and 7.12 mg/L air, respectively. Meanwhile, L. serricorne was the most sensitive to 2-tridecanone (LD50 = 5.74 μg/adult) in the progress of contact toxicity assay.

Microphysical Properties of Alaskan Volcanic Ash

Science.gov (United States)

Puthukkudy, A.; Espinosa, R.; Rocha Lima, A.; Remer, L.; Colarco, P. R.; Whelley, P.; Krotkov, N. A.; Young, K.; Dubovik, O.; Wallace, K.; Martins, J. V.

2017-12-01

Volcanic ash has the potential to cause a variety of severe problems for human health and the environment. Therefore, effective monitoring of the dispersion and fallout from volcanic ash clouds and characterization of the aerosol particle properties are essential. One way to acquire information from volcanic clouds is through satellite remote sensing: such images have greater coverage than ground-based observations and can present a "big picture" perspective. A challenge of remote sensing is that assumptions of certain properties of the target are often a pre-requisite for making accurate and quantitative retrievals. For example, detailed information about size distribution, sphericity, and optical properties of the constituent matter is needed or must be assumed. The same kind of information is also needed for atmospheric transport models to properly simulate the dispersion and fallout of volcanic ash. Presented here is a laboratory method to determine the microphysical and optical properties of volcanic ash samples collected from two Alaskan volcanoes with markedly different compositions. Our method uses a Polarized Imaging Nephelometer (PI-Neph) and a system that re-suspends the particles in an air flow. The PI-Neph measures angular light scattering and polarization of the re-suspended particles from 3o to 175o in scattering angle, with an angular resolution of 1o . Primary measurements include phase function and polarized phase function at three wavelengths (445nm, 532nm, and 661nm). Size distribution, sphericity, and complex refractive index are retrieved indirectly from the PI-Neph measurements using the GRASP (Generalized Retrieval of Aerosol and Surface Properties) inversion algorithm. We report the results of this method applied to samples from the Mt. Okmok (2008) and Mt. Katmai (1912) volcanic eruptions. To our knowledge, this is the first time direct measurements of phase matrix elements of ash from Mt. Okmok and Mt. Katmai have been reported. Retrieved

A Comparative study Of Catalityc Activity Of Heterogeneous Base Of Banana Stem Ash And Fly Ash On Production Of Biodiesel Byultrasonic

OpenAIRE

Marlinda; Ramli; Muh. Irwan

2015-01-01

Abstract The use of heterogeneous catalysts in the production of biodiesel provides many advantages due to heterogeneous catalysts can be easily separated from the product so that it can be reused. This research using heterogeneous catalysts derived from natural materials namely banana stem ash and coal fly ash containing alkali and alkaline earth elements. The preparation of catalyst from banana stem ash and coal fly ash used activator KOH 1.9 N and impregnation with KNO3 15 and then heated...

Water retention properties of ashes; Vattenretentionsegenskaper hos aska

Energy Technology Data Exchange (ETDEWEB)

Hemstroem, Kristian; Ezziyani, Samir; Bendz, David

2009-05-15

The water holding properties of a material can be described with a water retention curve (also called pF curve or characteristic curve). The importance of this material property has until now been neglected in waste and rest products contexts. There is an eminent need for knowledge of the water holding properties of ash and rest products in order to improve the possibility to perform i) assessment of leaching from rest product used in constructions, ii) dimensioning of covers built with rest products and iii) assessment of long term properties of land fill waste concerning leaching, especially for stabilized ash with a monolithic characteristics. The aim of this project was to increase the knowledge of the water holding properties of ashes by determining water retention curves with laboratory methods on four ash materials with the potential to be used in constructions. In the project, four ashes has been studied; one MSWI bottom ash from SYSAV, one aged MSWI bottom ash from Gaerstadverket and two fly ashes from incineration of biofuels; one from SCA Ortviken and one from Jaemtkraft AB. For comparison, data from a silt soil studied in another SGI project is presented. When determining a water retention curve for a specific material water from the examined, beforehand water saturated, sample is eliminated under controlled circumstances in a pressure plate extractor. The sample is exposed to a pressure, with increasing degree, squeezing excess water out of the material. The excess water is measured for each increased pressure step and the remaining volumetric water content in the material can be calculated. The results from such measurements are presented in water retention curves, in which the volumetric water content is plotted as a function of the capillary pressure. The water retention curves shows how various materials differ in water content at the same pressure. The results from the study showed that ashes have great water holding capacity. The study also

Environmental effects of ash application in forest ecosystems

DEFF Research Database (Denmark)

Hansen, Mette

of ashes being produced and the export of nutrients from the forests. This PhD project aims at investigating how ash application in forest ecosystems affects soil and soil solution properties and whether ash application can be used in a Danish context without environmental harm but with positive effects...

Plant nutrition on fly-ash

Energy Technology Data Exchange (ETDEWEB)

Rees, W J; Sidrak, G H

1956-12-01

Experiments were performed to determine the plant nutritional potential of fly ash. Chemical analysis indicates that it contains all the essential nutrients. It is deficient in nitrogen and only manganese and aluminum appear to be available in quantities toxic to plants. Barley and spinach grown on fly ash accumulate excessive quantities of Al and Mn in their leaves and exhibit symptoms of toxicities of these metals. Atriplex hastata grows vigorously on the ash, has a high Al and Mn leaf content, but does not show toxicity symptoms. Atriplex, barley and spinach grown at reduced N levels gave lower yields than the normal controls, but symptoms of N deficiency which were evident in barley and spinach were not observed in Atriplex. 17 references, 2 figures, 14 tables.

Economic analysis of emerald ash borer (Coleoptera: Buprestidae) management options.

Science.gov (United States)

Vannatta, A R; Hauer, R H; Schuettpelz, N M

2012-02-01

Emerald ash borer, Agrilus planipennis (Fairmaire) (Coleoptera: Buprestidae), plays a significant role in the health and extent of management of native North American ash species in urban forests. An economic analysis of management options was performed to aid decision makers in preparing for likely future infestations. Separate ash tree population valuations were derived from the i-Tree Streets program and the Council of Tree and Landscape Appraisers (CTLA) methodology. A relative economic analysis was used to compare a control option (do-nothing approach, only removing ash trees as they die) to three distinct management options: 1) preemptive removal of all ash trees over a 5 yr period, 2) preemptive removal of all ash trees and replacement with comparable nonash trees, or 3) treating the entire population of ash trees with insecticides to minimize mortality. For each valuation and management option, an annual analysis was performed for both the remaining ash tree population and those lost to emerald ash borer. Retention of ash trees using insecticide treatments typically retained greater urban forest value, followed by doing nothing (control), which was better than preemptive removal and replacement. Preemptive removal without tree replacement, which was the least expensive management option, also provided the lowest net urban forest value over the 20-yr simulation. A "no emerald ash borer" scenario was modeled to further serve as a benchmark for each management option and provide a level of economic justification for regulatory programs aimed at slowing the movement of emerald ash borer.

Physical, chemical and mineralogical properties of fly ash

International Nuclear Information System (INIS)

Khairul Nizar Ismail; Kamaruddin Hussin; Mohd Sobri Idris

2007-01-01

Fly ash is the finely divided mineral residue resulting from the combustion of coal in electric generating plants. Fly ash consists of inorganic, incombustible matter present in the coal that has been fused during combustion into a glassy, amorphous structure. Fly ash particles are generally spherical in shape and range in size from 2 μm to 10 μm. They consist mostly of silicon dioxide (SiO 2 ), aluminium oxide (Al 2 O 3 ) and iron oxide (Fe 2 O 3 ). Fly ash like soil contains trace concentrations of the following heavy metals: nickel, vanadium, cadmium, barium, chromium, copper, molybdenum, zinc and lead. The chemical compositions of the sample have been examined and the fly ash are of ASTM C618 Class F. (Author)

Preliminary Evaluation of Potassium Extraction from Bamboo Ash

Directory of Open Access Journals (Sweden)

Samadhi Tjokorde W.

2018-01-01

Full Text Available Bamboo is a potentially economical fuel crop that has not been utilized at a substantial extent for energy generation in Indonesia. As a thermal conversion waste, bamboo ash is particularly interesting due to its high potassium content. This paper discusses the determination of several key parameters of a simple batchwise extraction process to recover potassium in the form of weak solution from bamboo ash. To produce the ash, black bamboo (Gigantochloa atroviolaceae is charred in a fixed bed combustor. The bamboo char is ground and ashed at 500 °C in an electric furnace. The ash yield is 3.3 %-mass relative to as-received ash, with an ash K2O content of 12.9 %-mass. The ash is ground until passing 100-mesh standard sieve, and extracted by deionized water on a 2-stage laboratory-scale batchwise extractor battery. Process variables include extractror battery configuration (counter-current and co-current, temperature (nominal setting at 45-80 °C, and contact period of 1-6 hours. The concentration of extracted K2O increases asymptotically with temperature and contact time. Counter-current extraction yields more than twice the extract K2O concentration compared to cross-current extraction. The optimum conditions for the counter-current extraction is identified as a temperature of 78 °C and contact time of 4 hours, resulting in a 0.70 %-mass K2O solution concentration. Spot sampling of commercial liquid fertilizer products in Indonesia indicates an equivalent K2O content of 0.08-13.6 %-mass, suggesting the potential of the bamboo ash extract as an intermediate for fertilizer product.

Wood ash as a soil additive and liming agent

International Nuclear Information System (INIS)

Campbell, A.; Etiegni, L.; Mahler, R.L.

1991-01-01

This study evaluated wood ash as an agricultural soil supplement and liming material. Winter wheat (Triticum aestivum) and poplar (Populus sp.) were grown in a greenhouse on six different Idaho soils amended with different ash concentrations. At ash levels equal to or lower than 2%, no detrimental effects were observed. In fact, the biomass of the wheat and the caliper and height of the poplar cuttings increased more at 2% ash 940 metric tons/ha than with the control soil. These results suggest that wood ash could be used in agricultural applications as a low analysis fertilizer containing potassium and as a liming agent. Land application of wood ash could be less expensive and more environmentally sound than present landfilling practices

Flue gas desulfurization gypsum and fly ash

International Nuclear Information System (INIS)

1992-05-01

The Cumberland Fossil Plant (CUF) is located in Stewart County, Tennessee, and began commercial operation in 1972. This is the Tennessee Valley Authority's newest fossil (coal-burning) steam electric generating plant. Under current operating conditions, the plant burns approximately seven million tons of coal annually. By-products from the combustion of coal are fly ash, approximately 428,000 tons annually, and bottom ash, approximately 115,000 tons annually. Based on historical load and projected ash production rates, a study was initially undertaken to identify feasible alternatives for marketing, utilization and disposal of ash by-products. The preferred alternative to ensure that facilities are planned for all by-products which will potentially be generated at CUF is to plan facilities to handle wet FGD gypsum and dry fly ash. A number of different sites were evaluated for their suitability for development as FGD gypsum and ash storage facilities. LAW Engineering was contracted to conduct onsite explorations of sites to develop information on the general mature of subsurface soil, rock and groundwater conditions in the site areas. Surveys were also conducted on each site to assess the presence of endangered and threatened species, wetlands and floodplains, archaeological and cultural resources, prime farmland and other site characteristics which must be considered from an environmental perspective

Trace elements of coal, coal ashes and fly ashes by activation analysis with shor-lived nuclides

International Nuclear Information System (INIS)

Boeck, H.; Sarac, I.; Grass, F.

1981-01-01

On irradiation with neutrons, some of the interesting trace elements in coal, coal ash and fly ash produce short-lived nuclides which may be determined - together with some of the matrix elements - by activation analysis. This enables the characterization of samples. To find out the distribution of elements in the gaseous or aerosol exhaust of fossil-fired power plants, the authors simulated the combustion in a quartz apparatus containing a cold trap, using the combustion temperature (780 deg C) employed for the standard ash determination. High Se values were found in the cold trap deposits of black coal from Poland. Halogens were also found in the deposits. (authors)

Pemanfaatan limbah abu terbang (fly ash) , abu dasar (bottom ash) batubara dan limbah padat (sludge) industri karet sebagai bahan campuran pada pembuatan batako

OpenAIRE

Faisal, Hendri

2012-01-01

Brick-making research has been conducted from a mixture of fly ash as a cement mixed with aggregate materials based bottom ash and sludge, and sand, where fly ash and cement used as an adhesive matrix. The percentage addition of fly ash is 10%, 20%, 30%, 40% and 50% of initial weight of cement. The percentage addition of bottom ash and sludge as an aggregate is 5%, 10%, 15%, 20% and 25% of initial weight of sand with the time of hardening for 28 days. Parameter tests performed include: metals...

Zanthoxylum piperitum DC ethanol extract suppresses fat accumulation in adipocytes and high fat diet-induced obese mice by regulating adipogenesis.

Science.gov (United States)

Gwon, So Young; Ahn, Ji Yun; Kim, Tae Wan; Ha, Tae Youl

2012-01-01

This study was conducted to determine the anti-obesity effects of Zanthoxylum piperitum DC fruit ethanol extract (ZPE) in 3T3-L1 adipocytes and obese mice fed a high-fat diet. We evaluated the influence of the addition of ZPE to a high-fat diet on body weight, adipose tissue weight, serum and hepatic lipids in C57BL/6 mice. In addition, adipogenic gene expression was determined by Western blot and real-time reverse transcription-PCR analysis. We assessed the effect of ZPE on 3T3-L1 preadipocyte differentiation. ZPE reduced weight gain, white adipose tissue mass, and serum triglyceride and cholesterol levels (pZPE decreased lipid accumulation and PPARγ, C/EBPα, SREBP-1, and FAS protein and mRNA levels in the liver. ZPE inhibited in vitro adipocyte differentiation in a dose-dependent manner and significantly attenuated adipogenic transcription factors, such as PPARγ, C/EBPα, and SREBP-1 in 3T3L1 cells. These findings suggest that Z. piperitum DC exerts an anti-obesity effect by inhibiting adipogenesis through the downregulation of genes involved in the adipogenesis pathway.

Laboratory rearing of emerald ash borer

Science.gov (United States)

Leah S. Bauer; Robert A. Haack; Deborah L. Miller; Houping Liu; Toby Petrice

2004-01-01

The emerald ash borer (EAB), Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), native to several Asian countries, was identified in 2002 as the cause of ash (Fraxinus spp.) mortality throughout southeastern Michigan and southwestern Ontario. More isolated infestations continue to be found throughout Lower Michigan, northern...

Fusibility and sintering characteristics of ash

Energy Technology Data Exchange (ETDEWEB)

Ots, A. A., E-mail: aots@sti.ttu.ee [Tallinn University of Technology (Estonia)

2012-03-15

The temperature characteristics of ash fusibility are studied for a wide range of bituminous and brown coals, lignites, and shales with ratios R{sub B/A} of their alkaline and acid components between 0.03 and 4. Acritical value of R{sub B/A} is found at which the fusion temperatures are minimal. The sintering properties of the ashes are determined by measuring the force required to fracture a cylindrical sample. It is found that the strength of the samples increases sharply at certain temperatures. The alkali metal content of the ashes has a strong effect on their sintering characteristics.

Environmentally-Friendly Dense and Porous Geopolymers Using Fly Ash and Rice Husk Ash as Raw Materials

Directory of Open Access Journals (Sweden)

Daniele Ziegler

2016-06-01

Full Text Available This paper assesses the feasibility of two industrial wastes, fly ash (FA and rice husk ash (RHA, as raw materials for the production of geopolymeric pastes. Three typologies of samples were thus produced: (i halloysite activated with potassium hydroxide and nanosilica, used as the reference sample (HL-S; (ii halloysite activated with rice husk ash dissolved into KOH solution (HL-R; (iii FA activated with the alkaline solution realized with the rice husk ash (FA-R. Dense and porous samples were produced and characterized in terms of mechanical properties and environmental impact. The flexural and compressive strength of HL-R reached about 9 and 43 MPa, respectively. On the contrary, the compressive strength of FA-R is significantly lower than the HL-R one, in spite of a comparable flexural strength being reached. However, when porous samples are concerned, FA-R shows comparable or even higher strength than HL-R. Thus, the current results show that RHA is a valuable alternative to silica nanopowder to prepare the activator solution, to be used either with calcined clay and fly ash feedstock materials. Finally, a preliminary evaluation of the global warming potential (GWP was performed for the three investigated formulations. With the mix containing FA and RHA-based silica solution, a reduction of about 90% of GWP was achieved with respect to the values obtained for the reference formulation.

Methods to Improve Survival and Growth of Planted Alternative Species Seedlings in Black Ash Ecosystems Threatened by Emerald Ash Borer

Directory of Open Access Journals (Sweden)

Nicholas Bolton

2018-03-01

Full Text Available Emerald ash borer (EAB continues to spread across North America, infesting native ash trees and changing the forested landscape. Black ash wetland forests are severely affected by EAB. As black ash wetland forests provide integral ecosystem services, alternative approaches to maintain forest cover on the landscape are needed. We implemented simulated EAB infestations in depressional black ash wetlands in the Ottawa National Forest in Michigan to mimic the short-term and long-term effects of EAB. These wetlands were planted with 10 alternative tree species in 2013. Based on initial results in the Michigan sites, a riparian corridor in the Superior Municipal Forest in Wisconsin was planted with three alternative tree species in 2015. Results across both locations indicate that silver maple (Acer saccharinum L., red maple (Acer rubrum L., American elm (Ulmus americana L., and northern white cedar (Thuja occidentalis L. are viable alternative species to plant in black ash-dominated wetlands. Additionally, selectively planting on natural or created hummocks resulted in two times greater survival than in adjacent lowland sites, and this suggests that planting should be implemented with microsite selection or creation as a primary control. Regional landowners and forest managers can use these results to help mitigate the canopy and structure losses from EAB and maintain forest cover and hydrologic function in black ash-dominated wetlands after infestation.

Removal of chloride from MSWI fly ash.

Science.gov (United States)

Chen, Wei-Sheng; Chang, Fang-Chih; Shen, Yun-Hwei; Tsai, Min-Shing; Ko, Chun-Han

2012-10-30

The high levels of alkali chloride and soluble metal salts present in MSWI fly ash is worth noting for their impact on the environment. In addition, the recycling or reuse of fly ash has become an issue because of limited landfill space. The chloride content in fly ash limits its application as basis for construction materials. Water-soluble chlorides such as potassium chloride (KCl), sodium chloride (NaCl), and calcium chloride hydrate (CaCl(2) · 2H(2)O) in fly ash are easily washed away. However, calcium chloride hydroxide (Ca(OH)Cl) might not be easy to leach away at room temperature. The roasting and washing-flushing processes were applied to remove chloride content in this study. Additionally, air and CO(2) were introduced into the washing process to neutralize the hazardous nature of chlorides. In comparison with the water flushing process, the roasting process is more efficient in reducing the process of solid-liquid separation and drying for the reuse of Cl-removed fly ash particles. In several roasting experiments, the removal of chloride content from fly ash at 1050°C for 3h showed the best results (83% chloride removal efficiency). At a solid to liquid ratio of 1:10 the water-flushing process can almost totally remove water-soluble chloride (97% chloride removal efficiency). Analyses of mineralogical change also prove the efficiency of the fly ash roasting and washing mechanisms for chloride removal. Copyright © 2012 Elsevier B.V. All rights reserved.

Determination of heavy metals in chinese prickly ash from different ...

African Journals Online (AJOL)

Methods: CPA samples collected from different production areas in China were subjected to microwave digestion, and the contents of copper (Cu), nickel (Ni), chromium (Cr), lead (Pb), cadmium (Cd), arsenic (As), mercury (Hg), tin (Sn), and antimony (Sb) were determined by inductively coupled plasma-mass spectrometry ...

Determination of heavy metals in chinese prickly ash from different ...

African Journals Online (AJOL)

digestion, and the contents of copper (Cu), nickel (Ni), chromium (Cr), lead (Pb), cadmium ... concentrations of heavy metals in these CPA samples mean they are safe for human consumption. ... poisoning, including Pb, Cd, As, Hg, Sn, and Sb.

Relation of ash composition to the uses of coal

Energy Technology Data Exchange (ETDEWEB)

Fieldner, A C; Selvig, W A

1926-02-01

The effects of coal ash and ash components on the utilization of coal for coke and gas production, steam generation, water gas production, smithing, and domestic uses were described in a review of literature. Calcite, gypsum, and pyrite which occur in high amounts in coal, increase the ash fusibility of the coal and render it unsuitable for many industrial and domestic uses. As a rule, coal ash of high Si content and low Fe content would not be readily fusible. High amounts of ash in coal also have the effect of reducing the heating value of the coal.

The use of shale ash in dry mix construction materials

Science.gov (United States)

Gulbe, L.; Setina, J.; Juhnevica, I.

2017-10-01

The research was made to determine the use of shale ash usage in dry mix construction materials by replacing part of cement amount. Cement mortar ZM produced by SIA Sakret and two types of shale ashes from Narva Power plant (cyclone ash and electrostatic precipitator ash) were used. Fresh mortar properties, hardened mortar bulk density, thermal conductivity (λ10, dry) (table value) were tested in mortar ZM samples and mortar samples in which 20% of the amount of cement was replaced by ash. Compressive strenght, frost resistance and resistance to sulphate salt solutions were checked. It was stated that the use of electrostatic precipitator ash had a little change of the material properties, but the cyclone ash significantly reduced the mechanical strength of the material.

Dynamic evaluation of municipal solid waste ash leachate

International Nuclear Information System (INIS)

Theis, T.L.; Gardner, K.H.

1992-01-01

The incineration of municipal solid waste (MSW) produces ashes which are concentrated in many inorganic species. The release of toxic elements from the ash to the aqueous environment is of concern as present methods of ash disposal consist primarily of landfilling. It was the goal of this paper to achieve an understanding of the mechanisms by which elements are transported from the solid ash phase to the aqueous phase. Twelve ash samples were collected from six different incinerators with varying designs and capacities. The leaching experiments were conducted using small (mini) dynamic columns to investigate the variation of leachate chemical characteristics with time. In analyzing the data, a multicomponent chemical equilibrium model was used to determine chemical speciation and component activities. Auxiliary experiments included an array of physical measurements, and aqueous batch leach tests

Stream Water, Carbon and Total Nitrogen Load Responses to a Simulated Emerald Ash Borer Infestation in Black Ash Dominated Headwater Wetlands

Science.gov (United States)

Van Grinsven, M. J.; Shannon, J.; Noh, N. J.; Kane, E. S.; Bolton, N. W.; Davis, J.; Wagenbrenner, J.; Sebestyen, S. D.; Kolka, R.; Pypker, T. G.

2017-12-01

The rapid and extensive expansion of emerald ash borer (EAB) is considered an important ecological and economic disturbance, and will likely affect critical ecosystem services associated with black ash wetlands. It is unknown how EAB-induced disturbance in wetlands dominated with black ash will impact stream water, dissolved organic carbon (DOC) and total dissolved nitrogen (TDN) export dynamics. We hypothesized that loads of water, DOC and TDN exported from black ash wetlands would be elevated following an EAB-induced disturbance. Stream water, DOC and TDN loads exiting two black ash wetlands in headwater watersheds in Michigan were quantified over a four-year period, and were combined with wetland soil temperature and soil decomposition rate monitoring to better understand the biogeochemical implications of an EAB-induced disturbance. After a two-year baseline monitoring period, an EAB disturbance was simulated by felling (ash-cut) all black ash trees with diameters greater than 2.5-cm in one wetland. When compared to the unaltered control, stream water DOC and TDN concentrations exiting the ash-cut wetland were significantly larger by 39% and 38%, respectively during the post-treatment study period. The significantly elevated DOC and TDN concentrations were likely associated with the higher soil temperatures and increased rates of soil decomposition detected in the ash-cut site during the post-treatment period. No significant mean daily stream discharge differences were detected between treatments during the pre-treatment period, however the 0.46 mm d-1 mean daily stream discharge exiting the ash-cut wetland was significantly smaller than the 1.07 mm d-1 exiting the unaltered control during the post-treatment study period. The significantly smaller daily stream discharge in the ash-cut site likely contributed to the fact no significant differences between treatments for either mean daily DOC loads or TDN loads were detected during the post-treatment period

Wildland fire ash: Production, composition and eco-hydro-geomorphic effects

Science.gov (United States)

Bodi, Merche B.; Martin, Deborah; Balfour, Victoria N.; Santin, Cristina; Doerr, Stefan H.; Pereira, Paulo; Cerda, Artemi; Mataix-Solera, Jorge

2014-01-01

Fire transforms fuels (i.e. biomass, necromass, soil organic matter) into materials with different chemical and physical properties. One of these materials is ash, which is the particulate residue remaining or deposited on the ground that consists of mineral materials and charred organic components. The quantity and characteristics of ash produced during a wildland fire depend mainly on (1) the total burned fuel (i.e. fuel load), (2) fuel type and (3) its combustion completeness. For a given fuel load and type, a higher combustion completeness will reduce the ash organic carbon content, increasing the relative mineral content, and hence reducing total mass of ash produced. The homogeneity and thickness of the ash layer can vary substantially in space and time and reported average thicknesses range from close to 0 to 50 mm. Ash is a highly mobile material that, after its deposition, may be incorporated into the soil profile, redistributed or removed from a burned site within days or weeks by wind and water erosion to surface depressions, footslopes, streams, lakes, reservoirs and, potentially, into marine deposits.Research on the composition, properties and effects of ash on the burned ecosystem has been conducted on material collected in the field after wildland and prescribed fires as well as on material produced in the laboratory. At low combustion completeness (typically T  450 °C), most organic carbon is volatized and the remaining mineral ash has elevated pH when in solution. It is composed mainly of calcium, magnesium, sodium, potassium, silicon and phosphorous in the form of inorganic carbonates, whereas at T > 580 °C the most common forms are oxides. Ash produced under lower combustion completeness is usually darker, coarser, and less dense and has a higher saturated hydraulic conductivity than ash with higher combustion completeness, although physical reactions with CO2 and when moistened produce further changes in ash characteristics.As a new

The stability of clay using volcanic ash of Mount Sinabung North Sumatera and sugarcane bagasse ash with cbr and uct value

Directory of Open Access Journals (Sweden)

Hastuty Ika Puji

2017-01-01

Full Text Available Soil is the fundamental material that is extremely as the place of establishment of a structure or construction, both building and road constructions. However, not all soil is well used in the constructions field, as there are several types of soil that are problematic in terms of both the soil bearing capacity and deformation. The clay with carrying capacity and low shear strength needs to stabilized in order to meet the technical requirements to be used as sub grade. The add materials that are typically used for soil stabilization are cement, lime or a mixture of two or three of the added materials. In this study, the added material use volcanic ash of Mount Sinabung at North Sumatera and sugarcane bagasse ash. The purpose of this study was to determine an index value of properties as the result of the addition of 4% volcanic ash and variations in content of bagasse ash on clay and then to determine the compressive strength for maximum testing UCT (Unconfined Compression Test and understand the value of CBR (California Bearing Capacity as the consequence of the addition of a stabilizing agent, as well as optimum level of addition of bagasse ash. The result showed that the original soil sample has the water content 12.35%, specific gravity of 2.65, liquid limit of 46.73% and plasticity index of 26.44%. The compressive strength value of 1.38 kg/cm2. Base on the USCS classification, the soil sample including the type CL while base on AASHTO classification, soil samples are include this A-7-6 type. After the soil is stabilized with a wide variety of sugarcane bagasse ash content value obtained the largest unconfined compression test in 4% addition level volcanic ash + 10% sugarcane bagasse ash is equal to 5.1kg/cm2 and the result California Bearing capacity value on the optimal mix of 4% volcanic ash + 4% sugarcane bagasse ash is equal to 13.91%.

Possibilities for the Use of Wood Ashes in Agriculture

OpenAIRE

Barbara Symanowicz; Marcin Becher; Dawid Jaremko; Korneliusz Skwarek

2018-01-01

The aim of the study was to determine the agricultural usefulness of the ashes obtained following the combustion of wood of fourteen tree species (pear tree, apple tree, aspen, ash, alder, birch, poplar, hornbeam, pine, common walnut, oak, hazel, bird cherry and spruce) in home fireplaces. The following physical properties of the ashes were determined: colour, solubility, porosity, absorbability, compression strength, degree of fineness, moisture content and spreadability. In the ashes...

Biology of emerald ash borer parasitoids

Science.gov (United States)

Leah S. Bauer; Jian J. Duan; Jonathan P. Lelito; Houping Liu; Juli R. Gould

2015-01-01

The emerald ash borer (EAB) (Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), an invasive beetle introduced from China (Bray et al., 2011), was identified as the cause of ash (Fraxinus spp.) mortality in southeast Michigan and nearby Ontario in 2002 (Haack et al., 2002; Federal Register, 2003; Cappaert et al., 2005)....

FEATURES OF ASH OF THERMAL POWER PLANTS AS AGGREGATE FOR CONCRETES

Directory of Open Access Journals (Sweden)

M. A. Storozhuk

2017-10-01

Full Text Available Purpose. The scientific work is dedicated to development of scientific-technical bases of production and application of concrete on the basis of ashes of thermal power plants (TPP. Methodology. The properties of TPP ash, as well as the peculiarities of its behavior in a concrete mix as a fine aggregate, have been studied. It is shown that the hydrolysis and hydration of cement occur in the active environment of ash, which has a huge specific surface area. This significantly affects the course of these processes and the quality of the concrete produced. A new technology of application of ash of TPP for preparation of concrete mixes is offered. Vibrated and vibrovacuumized concretes of optimum composition from slag and ash, as well as from granite crushed stone and ash, are tested. The chara-cteristics of ordinary concrete (from granite crushed stone and quartz sand are given to compare. Findings. The results of the tests showed the possibility of obtaining concretes of class C20/25…C25/30 on the basis of slag and ash of TPP at a limited consumption of cement. It is shown that the concrete with traditional aggregates has a lower strength than the concrete, which has ash as fine aggregate. This research results contribute to the increased use of ash in construction that solves the problem of aggregates as well as thermal power plants waste recycling. Originality. New method and technology of application of TPP ashes in concrete are developed. Ash concrete mix has rational flowability, which produces the greatest strength of ash vacuum concrete. This strength is twice or more as large as the strength of vibrated ash concrete mix with flowability S1. Practical value. The physico-chemical properties of TPP ash as aggregate for concrete are presented. Significant difference of ash from ordinary aggregates is shown. Chemical activity of the ash is justified. The special conditions of cement hardening in the case of using ash as aggregate for concrete

COAL-FIRED UTILITY BOILERS: SOLVING ASH DEPOSITION PROBLEMS; TOPICAL

International Nuclear Information System (INIS)

Christopher J. Zygarlicke; Donald P. McCollor; Steven A. Benson; Jay R. Gunderson

2001-01-01

The accumulation of slagging and fouling ash deposits in utility boilers has been a source of aggravation for coal-fired boiler operators for over a century. Many new developments in analytical, modeling, and combustion testing methods in the past 20 years have made it possible to identify root causes of ash deposition. A concise and comprehensive guidelines document has been assembled for solving ash deposition as related to coal-fired utility boilers. While this report accurately captures the current state of knowledge in ash deposition, note that substantial research and development is under way to more completely understand and mitigate slagging and fouling. Thus, while comprehensive, this document carries the title ''interim,'' with the idea that future work will provide additional insight. Primary target audiences include utility operators and engineers who face plant inefficiencies and significant operational and maintenance costs that are associated with ash deposition problems. Pulverized and cyclone-fired coal boilers are addressed specifically, although many of the diagnostics and solutions apply to other boiler types. Logic diagrams, ash deposit types, and boiler symptoms of ash deposition are used to aid the user in identifying an ash deposition problem, diagnosing and verifying root causes, determining remedial measures to alleviate or eliminate the problem, and then monitoring the situation to verify that the problem has been solved. In addition to a step-by-step method for identifying and remediating ash deposition problems, this guideline document (Appendix A) provides descriptions of analytical techniques for diagnostic testing and gives extensive fundamental and practical literature references and addresses of organizations that can provide help in alleviating ash deposition problems

Large-scale ash recycling in Central Sweden; Storskalig askhantering i mellansverige

Energy Technology Data Exchange (ETDEWEB)

Hansson, Mats [Stora Skog (Sweden)

1998-08-01

When logging residues (tops, branches) are withdrawn from the forest, most of the nutrient content of the trees is also lost. Some of the nutrient content of the soil is restored by weathering, but not all. When biomass is burnt as fuel most of the nutrients will be found in the ash. By recycling wood ash, in similar amounts as was withdrawn with the biomass, it is possible to compensate for the nutrient losses. This project was initiated to study how a rational recycling of wood ash could be performed under conditions valid for Stora, a large forest company in the middle of Sweden. A second aim was to give guiding principles for Stora`s own ash recycling while awaiting instructions from the authorities. In the project both theoretical studies and practical field studies were carried out. Studied areas are production of a stabilised ash product and different systems for transport and spreading of the ash product. The costs and results of spreading have also been monitored. The project showed that spreading of the ash can normally only take place when there is no snow. If production or transport is carried out during another time of the year, the ash has to be stored, either at the industry, in an intermediate storage, or in the forest. One important conclusion from the test period was that the result of the spreading depends heavily on the quality of the ash. Some of the ashes hardened in the spreading equipment, causing a complete stop of the spreading. It also caused problems if the ash was too wet. Plate-spreaders led to unequal quality of spreading, where some areas got more ash and some got less. Granulated ash was most easy to spread. Recommended system for spreading ash is: granulated ash transported unpacked in separate transports with lorries with exchangeable platforms. A large fores tractor spreads the ash in clearings, in the summer. The project has shown that large-scale ash recycling is possible to realize 22 figs, 5 tabs, 13 appendices

SLAM: A multi-agency pilot project to SL.ow A.sh M.ortality caused by emerald ash borer in outlier sites

Science.gov (United States)

Therese M. Poland; Deborah G. McCullough

2010-01-01

Since its discovery in southeast Michigan in 2002, the emerald ash borer, Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), has continued to spread and kill ash (Fraxinus) trees at an alarming rate. As of February 2010, EAB has killed tens of millions of ash trees in Michigan, at least 12 additional U.S. states, and the...

Electrodialytic removal of Cd from biomass combustion fly ash suspensions

DEFF Research Database (Denmark)

Kirkelund, Gunvor M.; Ottosen, Lisbeth M.; Damoe, Anne J.

2013-01-01

was investigated with the aim of enabling reuse of the ashes. The ashes originated from combustion of straw (two ashes), wood chips, and co-firing of wood pellets and fuel oil, respectively. A series of laboratory scale electrodialytic remediation experiments were conducted with each ash. The initial Cd...

Stabilization of Fly Ash Deposits through Selected Cereal Crops

Directory of Open Access Journals (Sweden)

Florica Morariu

2012-10-01

Full Text Available Fly ash, a waste product from burning coal in power plants, occupies important spaces and is a major harm forenvironment: water, air, soil and associated ecosystems. New deposits do not have available nutrients for plantgrowth. The study presents a process of stimulating growth of oats in deposits of fly ash, which eliminates listed.Phytostabilization of new deposit is fast after fertilization with sewage sludge-based compost in the presence/absence of native or modified volcanic tuff with grain species, Avena sativa L., and variety Lovrin 1. Experimentalstudies have shown the species adaptability to climatic conditions and a growth rate until the maturity correlated withtype of treatment of upper layers of fly ash deposit. Fly ash with sewage sludge compost treatment 50 t/hadetermined the growth with 75% of the amount of grains vs. the amount of grains harvested from untreated fly ash.Fly ash with sewage sludge compost mixed with modified indigenous volcanic tuff 2.5 t/ha treatment determined thegrowth with 80% vs. the amount of grains harvested from untreated fly ash. If oat straw harvested from fertilizedvariant without modified indigenous volcanic tuff increases in weight are 30% and for fertilized variant in thepresence of tuff increases in weight are 39.8% vs. quantities harvested from untreated fly ash.

Meteorological Controls on Local and Regional Volcanic Ash Dispersal.

Science.gov (United States)

Poulidis, Alexandros P; Phillips, Jeremy C; Renfrew, Ian A; Barclay, Jenni; Hogg, Andrew; Jenkins, Susanna F; Robertson, Richard; Pyle, David M

2018-05-02

Volcanic ash has the capacity to impact human health, livestock, crops and infrastructure, including international air traffic. For recent major eruptions, information on the volcanic ash plume has been combined with relatively coarse-resolution meteorological model output to provide simulations of regional ash dispersal, with reasonable success on the scale of hundreds of kilometres. However, to predict and mitigate these impacts locally, significant improvements in modelling capability are required. Here, we present results from a dynamic meteorological-ash-dispersion model configured with sufficient resolution to represent local topographic and convectively-forced flows. We focus on an archetypal volcanic setting, Soufrière, St Vincent, and use the exceptional historical records of the 1902 and 1979 eruptions to challenge our simulations. We find that the evolution and characteristics of ash deposition on St Vincent and nearby islands can be accurately simulated when the wind shear associated with the trade wind inversion and topographically-forced flows are represented. The wind shear plays a primary role and topographic flows a secondary role on ash distribution on local to regional scales. We propose a new explanation for the downwind ash deposition maxima, commonly observed in volcanic eruptions, as resulting from the detailed forcing of mesoscale meteorology on the ash plume.

Removal mechanism of phosphate from aqueous solution by fly ash.

Science.gov (United States)

Lu, S G; Bai, S Q; Zhu, L; Shan, H D

2009-01-15

This work studied the effectiveness of fly ash in removing phosphate from aqueous solution and its related removal mechanism. The adsorption and precipitation of phosphate by fly ash were investigated separately in order to evaluate their role in the removal of phosphate. Results showed that the removal of phosphate by fly ash was rapid. The removal percentage of phosphate in the first 5min reached 68-96% of the maximum removal of phosphate by fly ash. The removal processes of phosphate by fly ash included a fast and large removal representing precipitation, then a slower and longer removal due to adsorption. The adsorption of phosphate on fly ash could be described well by Freundlich isotherm equation. The pH and Ca2+ concentration of fly ash suspension were decreased with the addition of phosphate, which suggests that calcium phosphate precipitation is a major mechanism of the phosphate removal. Comparison of the relative contribution of the adsorption and precipitation to the total removal of phosphate by fly ash showed that the adsorption accounted for 30-34% of the total removal of phosphate, depending on the content of CaO in fly ash. XRD patterns of the fly ash before and after phosphate adsorption revealed that phosphate salt (CaHPO4 x 2H2O) was formed in the adsorption process. Therefore, the removal of phosphate by fly ash can be attributed to the formation of phosphate precipitation as a brushite and the adsorption on hydroxylated oxides. The results suggested that the use of fly ash could be a promising solution to the removal of phosphate in the wastewater treatment and pollution control.

Emerald Ash Borer Threat Reveals Ecohydrologic Feedbacks in Northern U.S. Black Ash Wetlands

Science.gov (United States)

Diamond, J.; Mclaughlin, D. L.; Slesak, R.

2016-12-01

Hydrology is a primary driver of wetland structure and process that can be modified by abiotic and biotic feedbacks, leading to self-organization of wetland systems. Large-scale disturbance to these feedbacks, such as loss of vegetation, can thus be expected to impact wetland hydrology. The Emerald Ash Borer is an invasive beetle that is expected to cause widespread-loss of ash trees throughout the northern U.S. and Canada. To predict ecosystem response to this threat of vegetation loss, we ask if and how Black Ash (Fraxinus nigra), a ubiquitous facultative-wetland ash species, actively controls wetland hydrology to determine if Black Ash creates favorable hydrologic regimes for growth (i.e., evidence for ecohydrologic feedbacks). We do this by taking advantage of plot-level tree removal experiments in Black Ash-dominated (75-100% basal area) wetlands in the Chippewa National Forest, Minnesota. The monospecies dominance in these systems minimizes variation associated with species-specific effects, allowing for clearer interpretation of results regarding ecohydrologic feedbacks. Here, we present an analysis of six years of water table and soil moisture time series in experimental plots with the following treatments: 1) clear cut, 2) girdling, 3) group-selection thinning, and 4) control. We also present evapotranspiration (ET) time series estimates for each experimental plot using analysis of diel water level variation. Results show elevated water tables in treatment plots relative to control plots for all treatments for several years after treatments were applied, with differences as great as 50 cm. Some recovery of water table to pre-treatment levels was observed over time, but only the group-selection thinning treatment showed near-complete recovery to pre-treatment levels, and clear-cut treatments indicate sustained elevated water tables over five years. Differences among treatments are directly attributed to variably reduced ET relative to controls. Results also

Assessing fly ash treatment: remediation and stabilization of heavy metals.

Science.gov (United States)

Lima, A T; Ottosen, Lisbeth M; Ribeiro, Alexandra B

2012-03-01

Fly ashes from Municipal Solid Waste (MSW), straw (ST) and co-combustion of wood (CW) are here analyzed with the intent of reusing them. Two techniques are assessed, a remediation technique and a solidification/stabilization one. The removal of heavy metals from fly ashes through the electrodialytic process (EDR) has been tried out before. The goal of removing heavy metals has always been the reuse of fly ash, for instance in agricultural fields (BEK). The best removal rates are here summarized and some new results have been added. MSW fly ashes are still too hazardous after treatment to even consider application to the soil. ST ash is the only residue that gets concentrations low enough to be reused, but its fertilizing value might be questioned. An alternative reuse for the three ashes is here preliminary tested, the combination of fly ash with mortar. Fly ashes have been substituted by cement fraction or aggregate fraction. Surprisingly, better compressive strengths were obtained by replacing the aggregate fraction. CW ashes presented promising results for the substitution of aggregate in mortar and possibly in concrete. Copyright © 2010 Elsevier Ltd. All rights reserved.

Assessing fly ash treatment: Remediation and stabilization of heavy metals

KAUST Repository

Lima, A.T.

2010-12-17

Fly ashes from Municipal Solid Waste (MSW), straw (ST) and co-combustion of wood (CW) are here analyzed with the intent of reusing them. Two techniques are assessed, a remediation technique and a solidification/stabilization one. The removal of heavy metals from fly ashes through the electrodialytic process (EDR) has been tried out before. The goal of removing heavy metals has always been the reuse of fly ash, for instance in agricultural fields (BEK). The best removal rates are here summarized and some new results have been added. MSW fly ashes are still too hazardous after treatment to even consider application to the soil. ST ash is the only residue that gets concentrations low enough to be reused, but its fertilizing value might be questioned. An alternative reuse for the three ashes is here preliminary tested, the combination of fly ash with mortar. Fly ashes have been substituted by cement fraction or aggregate fraction. Surprisingly, better compressive strengths were obtained by replacing the aggregate fraction. CW ashes presented promising results for the substitution of aggregate in mortar and possibly in concrete. © 2010 Elsevier Ltd.

Assessing fly ash treatment: Remediation and stabilization of heavy metals

KAUST Repository

Lima, A.T.; Ottosen, Lisbeth M.; Ribeiro, Alexandra B.

2010-01-01

Fly ashes from Municipal Solid Waste (MSW), straw (ST) and co-combustion of wood (CW) are here analyzed with the intent of reusing them. Two techniques are assessed, a remediation technique and a solidification/stabilization one. The removal of heavy metals from fly ashes through the electrodialytic process (EDR) has been tried out before. The goal of removing heavy metals has always been the reuse of fly ash, for instance in agricultural fields (BEK). The best removal rates are here summarized and some new results have been added. MSW fly ashes are still too hazardous after treatment to even consider application to the soil. ST ash is the only residue that gets concentrations low enough to be reused, but its fertilizing value might be questioned. An alternative reuse for the three ashes is here preliminary tested, the combination of fly ash with mortar. Fly ashes have been substituted by cement fraction or aggregate fraction. Surprisingly, better compressive strengths were obtained by replacing the aggregate fraction. CW ashes presented promising results for the substitution of aggregate in mortar and possibly in concrete. © 2010 Elsevier Ltd.

Characterization of North American lignite fly ashes. II. XRD Mineralogy

International Nuclear Information System (INIS)

McCarthy, G.J.; Johansen, D.M.; Thedchanamoorthy, A.; Steinwand, S.J.; Swanson, K.D.

1988-01-01

X-ray powder diffraction has been used to determine the crystalline phase mineralogy in samples of fly ash from each of the lignite mining areas of North America. The characteristic phases of North Dakota lignite fly ashes were periclase, lime, merwinite and the sulfate phases anhydrite, thenardite and a sodalite-structure phase. Mullite was absent in these low-Al/sub 2/O/sub 3/ ashes. Montana lignite ash mineralogy had characteristics of ND lignite and MT subbituminous coal fly ashes; mullite and C/sub 3/A were present and the alkali sulfates were absent. Texas and Louisiana lignite fly ashes had the characteristic mineralogy of bituminous coal fly ash: quartz, mullite, ferrite-spinel (magnetite) and minor hematite. Even though their analytical CaO contents were 7-14%, all but one lacked crystalline CaO-containing phases. Lignite fly ashes from Saskatchewan were generally the least crystalline of those studied and had a mineralogy consisting of quartz, mullite, ferrite spinel and periclase. Quantitative XRD data were obtained. The position of the diffuse scattering maximum in the x-ray diffractograms was indicative of the glass composition of the lignite fly ash

evaluation of atomic absorption spectrophotometry (ashing, non ...

African Journals Online (AJOL)

cistvr

1Department of Agricultural and Food Science and 2Department of ... used techniques, namely atomic absorption spectrophotometry (AAS-Ashing and ..... fact that more preparation steps were involved in the Ashing procedure and thus.

Optimization of soil stabilization with class C fly ash.

Science.gov (United States)

1987-01-01

Previous Iowa DOT sponsored research has shown that some Class : C fly ashes are cementitious (because calcium is combined as calcium : aluminates) while other Class C ashes containing similar amounts of : elemental calcium are not (1). Fly ashes fro...

In vitro antibacterial effects of Zanthoxylum tingoassuiba root bark extracts and two of its alkaloids against multiresistant Staphylococcus aureus

Directory of Open Access Journals (Sweden)

Rafael S. Costa

Full Text Available ABSTRACT The emergence of multiresistant strains of bacteria reinforces the need to search for new compounds able to combat resistant organisms. Medicinal plants are a great resource of bioactive substances, providing the possibility of obtaining molecules with potential antimicrobial activity. The aim of the present study is the evaluation of the antibacterial activity of extracts and alkaloids isolated from the root bark of Zanthoxylum tingoassuiba A. St.-Hil., Rutaceae, against four resistant clinical isolates and Staphylococcus aureus ATCC 25923. The dichloromethane and methanol extracts were fractionated by chromatography on silica gel, leading to the isolation of dihydrocheleryhtrine and N-methylcanadine, identified by Nuclear Magnetic Resonance spectroscopy. The antibacterial activity of the extracts and isolated compounds was evaluated by the disc diffusion method and the minimum inhibitory concentration was determined. The dichloromethane extract was the most active against all the tested strains and the two pure alkaloids were more active than the extracts. The anti-MRSA activity of the two benzophenanthridine alkaloids is demonstrated for the first time in this study. These compounds appear as potential leads for the development of new anti-MRSA compounds and could be responsible for the antibacterial activity, justifying the ethnobotanical use of Z. tingoassuiba and other species for the treatment of various infectious diseases.

Volcanic ash modeling with the NMMB-MONARCH-ASH model: quantification of offline modeling errors

Science.gov (United States)

Marti, Alejandro; Folch, Arnau

2018-03-01

Volcanic ash modeling systems are used to simulate the atmospheric dispersion of volcanic ash and to generate forecasts that quantify the impacts from volcanic eruptions on infrastructures, air quality, aviation, and climate. The efficiency of response and mitigation actions is directly associated with the accuracy of the volcanic ash cloud detection and modeling systems. Operational forecasts build on offline coupled modeling systems in which meteorological variables are updated at the specified coupling intervals. Despite the concerns from other communities regarding the accuracy of this strategy, the quantification of the systematic errors and shortcomings associated with the offline modeling systems has received no attention. This paper employs the NMMB-MONARCH-ASH model to quantify these errors by employing different quantitative and categorical evaluation scores. The skills of the offline coupling strategy are compared against those from an online forecast considered to be the best estimate of the true outcome. Case studies are considered for a synthetic eruption with constant eruption source parameters and for two historical events, which suitably illustrate the severe aviation disruptive effects of European (2010 Eyjafjallajökull) and South American (2011 Cordón Caulle) volcanic eruptions. Evaluation scores indicate that systematic errors due to the offline modeling are of the same order of magnitude as those associated with the source term uncertainties. In particular, traditional offline forecasts employed in operational model setups can result in significant uncertainties, failing to reproduce, in the worst cases, up to 45-70 % of the ash cloud of an online forecast. These inconsistencies are anticipated to be even more relevant in scenarios in which the meteorological conditions change rapidly in time. The outcome of this paper encourages operational groups responsible for real-time advisories for aviation to consider employing computationally

Comparison of emerald ash borer preference for ash of different species, sun exposure, age, and stress treatments in relation to foliar volatiles and nutrition

Science.gov (United States)

Therese M. Poland; Deepa S. Pureswaran; Yigen Chen

2009-01-01

We investigated the host selection behavior and feeding preference of the emerald ash borer, Agrilus planipennis Fairmaire (Coleoptera: Buprestidae) on six different species of ash including Manchurian ash (F...

Progress and challenges of protecting North American ash trees from the emerald ash borer using biological control

Science.gov (United States)

Jian Duan; Leah Bauer; Roy van Driesche; Juli. Gould

2018-01-01

After emerald ash borer (EAB), Agrilus planipennis Fairmaire, was discovered in the United States, a classical biological control program was initiated against this destructive pest of ash trees (Fraxinus spp.). This biocontrol program began in 2007 after federal regulatory agencies and the state of Michigan approved release of...

Producing New Composite Materials by Using Tragacanth and Waste Ash

OpenAIRE

Yasar Bicer; Serif Yilmaz

2013-01-01

In present study, two kinds of thermal power plant ashes; one the fly ash and the other waste ash are mixed with adhesive tragacanth and cement to produce new composite materials. 48 new samples are produced by varying the percentages of the fly ash, waste ash, cement and tragacanth. The new samples are subjected to some tests to find out their properties such as thermal conductivity, compressive strength, tensile strength and sucking capability of water. It is found that; the thermal conduct...

Coal ash artificial reef demonstration

International Nuclear Information System (INIS)

Livingston, R.J.; Brendel, G.F.; Bruzek, D.A.

1991-01-01

This experimental project evaluated the use of coal ash to construct artificial reefs. An artificial reef consisting of approximately 33 tons of cement-stabilized coal ash blocks was constructed in approximately 20 feet of water in the Gulf of Mexico approximately 9.3 miles west of Cedar Key, Florida. The project objectives were: (1) demonstrate that a durable coal ash/cement block can be manufactured by commercial block-making machines for use in artificial reefs, and (2) evaluate the possibility that a physically stable and environmentally acceptable coal ash/cement block reef can be constructed as a means of expanding recreational and commercial fisheries. The reef was constructed in February 1988 and biological surveys were made at monthly intervals from May 1988 to April 1989. The project provided information regarding: Development of an optimum design mix, block production and reef construction, chemical composition of block leachate, biological colonization of the reef, potential concentration of metals in the food web associated with the reef, acute bioassays (96-hour LC 50 ). The Cedar Key reef was found to be a habitat that was associated with a relatively rich assemblage of plants and animals. The reef did not appear to be a major source of heavy metals to species at various levels of biological organization. GAI Consultants, Inc (GAI) of Monroeville, Pennsylvania was the prime consultant for the project. The biological monitoring surveys and evaluations were performed by Environmental Planning and Analysis, Inc. of Tallahassee, Florida. The chemical analyses of biological organisms and bioassay elutriates were performed by Savannah Laboratories of Tallahassee, Florida. Florida Power Corporation of St. Petersburg, Florida sponsored the project and supplied ash from their Crystal River Energy Complex

Geopolymer obtained from coal ash

International Nuclear Information System (INIS)

Conte, V.; Bissari, E.S.; Uggioni, E.; Bernardin, A.M.

2011-01-01

Geopolymers are three-dimensional alumino silicates that can be rapidly formed at low temperature from naturally occurring aluminosilicates with a structure similar to zeolites. In this work coal ash (Tractebel Energy) was used as source of aluminosilicate according a full factorial design in eight formulations with three factors (hydroxide type and concentration and temperature) and two-levels. The ash was dried and hydroxide was added according type and concentration. The geopolymer was poured into cylindrical molds, cured (14 days) and subjected to compression test. The coal ash from power plants belongs to the Si-Al system and thus can easily form geopolymers. The compression tests showed that it is possible to obtain samples with strength comparable to conventional Portland cement. As a result, temperature and molarity are the main factors affecting the compressive strength of the obtained geopolymer. (author)

Emerald ash borer survival in firewood

Science.gov (United States)

Robert A. Haack; Toby R. Petrice

2005-01-01

The emerald ash borer (EAB), Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), is native to Asia and was first discovered in Michigan and Ontario in 2002. As of October 2004, EAB was only found to breed in ash (Fraxinus) trees in North America. EAB is spreading naturally through adult flight as well as artificially through...

Upgrading and recovery of fertilizer value of ash from PYRONEER gasification

DEFF Research Database (Denmark)

Pares Viader, Raimon; Haugaard-Nielsen, Henrik

 leaching in the two ashes from gasification of sewage sludge with chemically precipitated P. In contrast, a considerable lower proportion of Al/Fe(III)-phosphates were found for the incineration sewage sludge ashes, whereas Ca was found to control P solubility at low pH for the ash with biologically precipitated P....... Using a 2-compartment electrodialytic cell, in which the ash suspension was acidified, over 80% of P could be recovered from both the Pyroneer ashes with biologically precipitated P and the incineration sewage sludge ashes. However, P recovery was limited to a 40% for the other two ashes using the same...

Pore Structure Characterization in Concrete Prepared with Carbonated Fly Ash

Science.gov (United States)

Sahoo, Sanjukta

2018-03-01

Carbon dioxide capture and storage (CCS) is a technique to address the global concern of continuously rising CO2 level in the atmosphere. Fly ash is considered as a suitable medium for CCS due to presence of metal oxides. The fly ash which has already sequestered carbon dioxide is referred to as carbonated fly ash. Recent research reveals better durability of concretes using carbonated fly ash as part replacement of cement. In the present research pore structure characterization of the carbonated fly ash concrete has been carried out. Mercury Intrusion porosimetry test has been conducted on control concrete and concrete specimens using fly ash and carbonated fly ash at replacement levels of 25% and 40%. The specimens have been water cured for 28 days and 90 days. It is observed that porosity reduction rate is more pronounced in carbonated fly ash concrete compared to control concrete at higher water curing age. Correlation analysis is also carried out which indicates moderately linear relationship between porosity % and pore distribution with particle size and water curing.

Prediction of ash deposition using CFD simulation combined to thermodynamic calculation

Energy Technology Data Exchange (ETDEWEB)

Takeshi Muratani; Takashi Hongo [UBE Industries, Ltd., Yamaguchi (Japan). Coal Department, Energy and Environment Division

2007-07-01

This study focused on the advanced ash deposition prediction using computational fluid dynamics (CFD) analysis combined to thermodynamic calculation, considering both combustion characteristics and ash fusibility. Combustion field in pulverised coal-fired boiler was calculated through the normal CFD process. As the post process of combustion calculation, ash particles were injected into the combustion field to calculate ash deposition by CFD, in which particle sticking sub-program was newly employed. In this post process, ash deposition condition for CFD calculation was defined with the ash fusibility data obtained from thermodynamic analysis. These results of ash deposition on the furnace wall showed good agreement with the plant observation. Furthermore, in order to improve the plant operation, some virtual cases were simulated, which might reduce ash deposition. 7 refs., 14 figs., 6 tabs.

Study on cement mortar and concrete made with sewage sludge ash.

Science.gov (United States)

Chang, F C; Lin, J D; Tsai, C C; Wang, K S

2010-01-01

This study investigated the feasibility of reusing wastewater sludge ash in construction materials to replace partial materials. Wastewater sludge sampled from thermal power plant was burned into sludge ash at 800°C in the laboratory. The sludge incineration ash has low heavy metal including Pb, Cd, Cr and Cu, so it belongs to general enterprise waste. The chemical composition of sludge incineration ash was summed up in SiO₂, CaO, Fe₂O₃ and MgO. Then the wastewater sludge ash is also found to be a porous material with irregular surface. When the sludge ash was used to replace mortar or concrete cement, its water-adsorption capability will result in the reduction of mortar workability and compressive strength. Cement is being substituted for sludge ash, and 10 percent of sludge ash is more appropriate. Sludge ash is reused to take the place of construction materials and satisfies the requests of standard specification except for higher water absorption.

Ash formation, deposition, corrosion, and erosion in conventional boilers

Energy Technology Data Exchange (ETDEWEB)

Benson, S.A.; Jones, M.L. [Univ. of North Dakota, Grand Forks, ND (United States)

1995-12-01

The inorganic components (ash-forming species) associated with coals significantly affect boiler design, efficiency of operation, and lifetimes of boiler parts. During combustion in conventional pulverized fuel boilers, the inorganic components are transformed into inorganic gases, liquids, and solids. This partitioning depends upon the association of the inorganic components in the coal and combustion conditions. The inorganic components are associated as mineral grains and as organically associated elements, and these associations of inorganic components in the fuel directly influence their fate upon combustion. Combustion conditions, such as temperature and atmosphere, influence the volatility and the interaction of inorganic components during combustion and gas cooling, which influences the state and size composition distribution of the particulate and condensed ash species. The intermediate species are transported with the bulk gas flow through the combustion systems, during which time the gases and entrained ash are cooled. Deposition, corrosion, and erosion occur when the ash intermediate species are transported to the heat-transfer surface, react with the surface, accumulate, sinter, and develop strength. Research over the past decade has significantly advanced understanding of ash formation, deposition, corrosion, and erosion mechanisms. Many of the advances in understanding and predicting ash-related issues can be attributed to advanced analytical methods to determine the inorganic composition of fuels and the resulting ash materials. These new analytical techniques have been the key to elucidation of the mechanisms of ash formation and deposition. This information has been used to develop algorithms and computer models to predict the effects of ash on combustion system performance.

On-conveyor belt determination of ash in coal

International Nuclear Information System (INIS)

Sowerby, B.; Lim, C.S.; Abernethy, D.A.; Liu, Y.; Maguire, P.A.

1997-01-01

A laboratory feasibility study has been carried out on new and advanced neutron and gamma-ray analysis systems for the direct on-conveyor belt analysis of ash in coal without the need for sample by-lines. Such an analysis system could deliver the combined advantages of a direct on-conveyor configuration with new and accurate analysis techniques. An industry survey of 18 coal companies carried out in early 1996 indicated that accurate on-belt ash analysis is of the highest priority. Subsequent laboratory work has focussed on the investigation of methods with the potential for improving the accuracy of ash content measurement relative to existing on-belt ash analysers, the most widely-used of which are based on dual energy gamma-ray transmission (DUET), which is sensitive to variations in ash composition. The current work indicates that on-belt neutron/gamma-ray techniques combined with advanced spectral analysis techniques show promise for development into an on-belt ash analysis system which is significantly less sensitive to composition changes than DUET and which analyses a much larger proportion of coal on the belt, thus eliminating some key sources of analysis error

Considerations on comprehensive risk assessment and mitigation planning of volcanic ash-fall

International Nuclear Information System (INIS)

Toshida, Kiyoshi

2010-01-01

Volcanic ash-fall is inevitable hazard throughout Japan, and causes wide range of effects due to its physical and chemical properties. Nuclear power plants in Japan face the necessity to assess the risk from volcanic ash-fall. Risk assessment of the volcanic ash-fall should include engineering solution and mitigation planning as well as the ash-fall hazard. This report points out the characteristics for reducing the various effects of volcanic ash-fall as follows. Large-scale eruptions produce prominent volcanic ash-falls that can approach power plants at a great distance. Aftermath hazards of ash-fall events, such as remobilization of fine ash particles and generation of lahars, require further assessments. The kind and extent of damages becomes greater whenever ash is wet. Wet ash requires separate assessments in contrast to dry ash. The mitigation and recovery measures at power plants involve quick cleanup operations of volcanic ash. Those operations should be prepared through comprehensive risk assessment, and by cooperation with authorities, during pre-eruption repose period. The comprehensive assessment for volcanic ash-fall hazards, however, has yet to be conducted. Development of risk communication method may result in increased implementation mitigation planning. Numerical analysis of the ash-fall hazards provides quantitative data on particle motions that can be used in the risk assessment. In order to implement the quantitative assessment method, the verification on the effect of ambient air condition to the altitude of volcanic ash cloud is necessary. We need to develop a three-dimensional model of volcanic ash cloud, and calculate motions of ash clouds under multiple conditions of ambient air. (author)

Water permeabilities of pulverized fuel ash; Bifuntan sekitanbai no tosui tokusei

Energy Technology Data Exchange (ETDEWEB)

Ichikawa, T [Center for Coal Utilization, Japan, Tokyo (Japan); Nagataki, S [Niigata University, Niigata (Japan); Hosoda, N [Kumagai Gumi Co. Ltd., Tokyo (Japan); Utsuki, T [The Coal Mining Research Center, Japan, Tokyo (Japan); Kubo, H [Obayashi Corp., Tokyo (Japan)

1996-09-01

It is intended to establish a technology to utilize coal ash in bulk to deal with its increasing production. In order to expand its use into earth engineering materials, two kinds of combustion ashes produced from dust coal burning power plants were used for studies using different kinds of tests. The tests were carried out on strength properties, water permeability, and characteristics of dissolving trace amounts of chemical constituents, with regard to addition effects of cement into compacted and slurry-state dust coal burned ashes. The derived findings may be summarized as follows: as the strength properties, the strength for both of the compacted and slurry-state ashes increases as the cement addition ratio is increased; growth of the strength due to the cement addition ratio and material age varies depending on the kinds of dust coal burned ash; comparison of strengths of the compacted and the slurry-state ashes indicates the strength of the latter ash is about one-third to quarter of that of the former ash; water permeability of the ashes decreases both in the compacted and slurry- state ashes as the cement addition ratio is increased; and the cement addition ratio gives greater impact to the water permeability than the density of the ashes. 28 figs., 5 tabs.

Leaching of assimilable silicon species from fly ash

International Nuclear Information System (INIS)

Piekos, R.; Paslawska, S.

1998-01-01

The objective of this study was to investigate the leaching of assimilable silicon species from coal fly ash with distilled water, sea waterand synthetic sea water at various fly ash/water ratios, pHs and temperatures. At the 1 g/100 ml fly ash/water ratio, less than 1 mg Si was found in 11 of aqueous slurries over the pH range 4-8 after 2 h at ambient temperature. The leaching was most effective at pH 10.5. At the fly ash/waterratio indicated, the pH of the suspensions decreased from 10.4 to 8.4 after 5days. The pH of fly ash slurries in sea water varied only slightly over time as compared with that in distilled water. Generally, the leaching of assimilable silicon species with distilled water was more intense than that with the sea water. 27 refs., 6 figs., 3 tabs

Hypocotyl derived in vitro regeneration of pumpkin ash (Fraxinus profunda)

Science.gov (United States)

Micah E. Stevens; Paula M. Pijut

2012-01-01

Pumpkin ash (Fraxinus profunda (Bush) Bush) is at risk for extirpation by an exotic insect, the emerald ash borer (EAB). Pumpkin ash is limited to wetland areas of the Eastern United States, and has been listed as an endangered species because of EAB activity. Pumpkin ash provides many benefits to the ecosystem, and its wood is used in the...

Components and Insecticidal Activity against the Maize Weevils of Zanthoxylum schinifolium Fruits and Leaves

Directory of Open Access Journals (Sweden)

Shu Shan Du

2011-04-01

Full Text Available In our screening program for new agrochemicals from Chinese medicinal herbs and wild plants, Zanthoxylum schinifolium essential oils were found to possess strong insecticidal activity against the maize weevil Sitophilus zeamais. The essential oils of Z. schinifolium fruits and leaves were extracted via hydrodistillation and investigated by GC and GC-MS. Estragole (69.52% was the major compound of the essential oil of fresh fruits, followed by linalool (8.63% and limonene (4.34% and 94.33% of the total components were monoterpenoids. The main components of the essential oil of fresh leaves were linalool (12.94%, ar-tumerone (8.95%, limonene (6.45% and elixene (5.43% and only 50.62% were monoterpenoids. However, the essential oil from purchased fruits contained linalool (33.42%, limonene (13.66% and sabinene (5.72%, followed by estragole (4.67%, nerol (4.56% and 4-terpineol (4.27%. Estragole, linalool and sabinene were separated and purified by silica gel column chromatography and preparative thin layer chromatography, and further identified by means of physicochemical and spectrometric analysis. The essential oil from the fresh fruits (LD50 = 15.93 μg/adult possessed two times more toxicity to the insects compared with that of fresh leaves (LD50 = 35.31 μg/adult. Estragole, linalool and sabinene exhibited contact activity against S. zeamais with LD50 values of 17.63, 13.90 and 23.98 μg/adult, respectively. The essential oils of Z. schinifolium possessed strong fumigant toxicity against S. zeamais adults with LC50 values of 13.19 mg/L (fresh fruits, 24.04 mg/L (fresh leaves and 17.63 mg/L (purchased fruits. Estragole, linalool and sabinene also exhibited strong fumigant toxicity against the maize weevils with LC50 values of 14.10, 10.46 and 9.12 mg/L, respectively.

Ash after forest fires. Effects on soil hydrology and erosion

Science.gov (United States)

Bodí, Merche B.

2013-04-01

Hillslopes were though to be most susceptible to enhanced hydro-geomorphological responses immediately following burning, with susceptibility declining during the first months or years depending on the soil and vegetation recovery. However, Cerdà (1998) found some indices in that immediately after the fire, the thin wettable ash layer that typically covers the ground could absorb rainfall and prevent or delay the onset of overland flow and associated erosion. Therefore the time lag while ash remains on the ground become of crucial importance to protect the soil after a wildfire. The effect of this ash layer was rarely been considered in detail because ash has often been reduced or redistributed by wind or water erosion before the onset of monitoring and thus the data collection typically begun some weeks or month after the fire. The first papers focussed only on ash and its hydrological effects were published by Cerdà and Doerr (2008) and by Woods and Balfour (2008). The results showed that the soil covered with ash indeed reduced and delayed surface runoff, reduced soil splash detachment and produced lower sediment yield compared to bare terrain. However, these findings arose more questions, as for instance: Why in other research there were indices that ash reduces infiltration? what is the mechanism by which why ash reduces overland flow? The research went further with Bodí PhD. First of all, it was crucial the agreement on the fact that the material "ash" is very variable depending on the original vegetation and the type and temperature of combustion. Therefore ash properties are different between wildfires even and within a fire. This is the main reason of its different effects and thus ash not always reduces runoff and sediment yield. In this way, depending on the nature of ash, it can increase overland flow if it is crusted (usually it contains a high content of calcium carbonate), it is water repellent (with high contents of organic carbon and specially

Synthetic aggregates from combustion ashes using an innovative rotary kiln.

Science.gov (United States)

Wainwright, P J; Cresswell, D J

2001-01-01

This paper describes the use of a number of different combustion ashes to manufacture synthetic aggregates using an innovative rotary 'Trefoil' kiln. Three types of combustion ash were used, namely: incinerated sewage sludge ash (ISSA); municipal solid waste incinerator bottom ash (MSWIBA-- referred to here as BA); and pulverised fuel ash (Pfa). The fine waste ash fractions listed above were combined with a binder to create a plastic mix that was capable of being formed into 'green pellets'. These pellets were then fired in a Trefoil kiln to sinter the ashes into hard fused aggregates that were then tested for use as a replacement for the natural coarse aggregate in concrete. Results up to 28 days showed that these synthetic aggregates were capable of producing concretes with compressive strengths ranging from 33 to 51 MPa, equivalent to between 73 and 112% of that of the control concrete made with natural aggregates.

Investigation of rye straw ash sintering characteristics and the effect of additives

International Nuclear Information System (INIS)

Wang, Liang; Skreiberg, Øyvind; Becidan, Michael; Li, Hailong

2016-01-01

Highlights: • Rye straw ash has a high sintering tendency at elevated temperatures. • Addition of additive increases melting temperature of the rye straw ash. • Kaolin addition leads to formation of silicates binding K in the ash. • Calcite and Ca-sludge promotes formation of silicates and phosphates in the ash. • Calcite addition restrains attaching and accumulation of rye straw ash melts. - Abstract: The understanding of ash sintering during combustion of agricultural residues is far from complete, because of the high heterogeneity of the content and composition of ash forming matters and the complex transformation of them. In order to make agricultural residues competitive fuels on the energy market, further research efforts are needed to investigate agricultural residues’ ash sintering behavior and propose relevant anti-sintering measures. The aim of this work was to investigate the ash characteristics of rye straw and effects of additives. Three additives were studied regarding their abilities to prevent and abate rye straw ash sintering. Standard ash fusion characterization and laboratory-scale sintering tests were performed on ashes from mixtures of rye straw and additives produced at 550 °C. Ash residues from sintering tests at higher temperatures were analyzed using a combination of X-ray diffraction (XRD) and scanning electron microscopy–energy dispersive X-ray spectrometry (SEM–EDX). High sintering and melting tendency of the rye straw ash at elevated temperatures was observed. Severe sintering of the rye straw ash was attributed to the formation and fusion of low temperature K–silicates and K–phosphates with high K/Ca ratios. Among the three additives, calcite served the best one to mitigate sintering of the rye straw ash. Ca from the calcite promoted formation of high temperature silicates and calcium rich K–phosphates. In addition, calcite may hinder aggregating of ash melts and further formation of large ash slag. Therefore

Can ash communities and their dependent species be partially protected through biological control of emerald ash borer

Science.gov (United States)

Ash trees were once relatively free of serious, major diseases and insect pests in North America until the arrival of the emerald ash borer (EAB), Agrilus planipennis Fairmaire, which was first detected in North America in Michigan in 2002 and has been detected in 32 U.S. states and two Canadian pro...

AL(0) in municipal waste incinerator ash

Science.gov (United States)

Stipp, S. L.; Ronsbo, J. G.; Zunic, T. B.; Christensen, T. H.

2003-04-01

Disposal of municipal waste is a challenge to society. Waste volume is substantially decreased by incineration but residual ash usually contains a number of toxic components which must be immobilised to insure environmental protection. One element, chromium, is mobile and toxic in its oxidised state as Cr(VI) but it can be reduced to Cr(III) and immobilised. Reduction can be promoted by ash treatment with Fe(0) or Fe(II), but recent evidence shows that at least some Cr(VI) is reduced spontaneously in the ash. Aspects of ash behaviour suggest metallic aluminium as the reducing agent, but no direct evidence of Al(0) has been found until now. We examined filter ash from an energy-producing, municipal-waste incinerator (Vest-forbrænding) near Copenhagen. X-ray diffraction (XRD) identified expected salts of Na, K and Ca such as halite, sylvite, calcite, anhydrite and gypsum as well as quartz, feldspar and some hematite. Wave-dispersive electron microprobe produced elemen-tal maps of the ash; Al-rich areas were analysed quantitatively by comparison with standards. We identified metallic Al particles, averaging 50 to 100 micrometers in di-ameter, often with a fractured, glassy border of aluminum oxide. The particles were porous, explaining fast Cr(VI) reduction and they contained thin exsolution lamellae of Al-alloys of Pb and Cu or Mn, Fe and Ag, which provide clues of the Al(0) origin in the waste. Sometimes Al(0) occurred inside glassy globes of Al2O3. Time-of-flight secondary ion mass spectroscopy (TOF-SIMS) and X-ray photoelectron spectroscopy (XPS) proved that surface Al concentrations on ash particles were below detection, confirming reactivity of the Al(0) bulk. The persistence of reduced Al through the highly oxidising combustion procedure comes as a surprise and is a benefit in the immobilisation of Cr(VI) from municipal-waste incineration residues.

Utilization of pulverized fuel ash in Malta

International Nuclear Information System (INIS)

Camilleri, Josette; Sammut, Michael; Montesin, Franco E.

2006-01-01

In Malta all of the waste produced is mixed and deposited at various sites around the island. None of these sites were purpose built, and all of the waste is above groundwater level. The landfills are not engineered and do not contain any measures to collect leachate and gases emanating from the disposal sites. Another waste, which is disposed of in landfills, is pulverized fuel ash (PFA), which is a by-product of coal combustion by the power station. This has been disposed of in landfill, because its use has been precluded due to the radioactivity of the ashes. The aim of this study was to analyze the chemical composition of the pulverized fuel ash and to attempt to utilize it as a cement replacement in normal concrete mixes in the construction industry. The levels of radiation emitted from the ashes were measured by gamma spectrometry. The results of this study revealed that although at early ages cement replacement by PFA resulted in a reduction in compressive strength (P = 0), when compared to the reference concrete at later ages the strengths measured on concrete cores were comparable to the reference concrete (P > 0.05). The utilization of PFA up to 20% cement replacement in concrete did not raise the radioactivity of the concrete. In conclusion, utilization of PFA in the construction industry would be a better way of disposing of the ashes rather than controlling the leachate and any radioactivity emitted by the landfilled ashes

Mercury capture by selected Bulgarian fly ashes: Influence of coal rank and fly ash carbon pore structure on capture efficiency

Science.gov (United States)

Kostova, I.J.; Hower, J.C.; Mastalerz, Maria; Vassilev, S.V.

2011-01-01

Mercury capture by fly ash C was investigated at five lignite- and subbituminous-coal-burning Bulgarian power plants (Republika, Bobov Dol, Maritza East 2, Maritza East 3, and Sliven). Although the C content of the ashes is low, never exceeding 1.6%, the Hg capture on a unit C basis demonstrates that the low-rank-coal-derived fly ash carbons are more efficient in capturing Hg than fly ash carbons from bituminous-fired power plants. While some low-C and low-Hg fly ashes do not reveal any trends of Hg versus C, the 2nd and, in particular, the 3rd electrostatic precipitator (ESP) rows at the Republika power plant do have sufficient fly ash C range and experience flue gas sufficiently cool to capture measurable amounts of Hg. The Republika 3rd ESP row exhibits an increase in Hg with increasing C, as observed in other power plants, for example, in Kentucky power plants burning Appalachian-sourced bituminous coals. Mercury/C decreases with an increase in fly ash C, suggesting that some of the C is isolated from the flue gas stream and does not contribute to Hg capture. Mercury capture increases with an increase in Brunauer-Emmett-Teller (BET) surface area and micropore surface area. The differences in Hg capture between the Bulgarian plants burning low-rank coal and high volatile bituminous-fed Kentucky power plants suggests that the variations in C forms resulting from the combustion of the different ranks also influence the efficiency of Hg capture. ?? 2010 Elsevier Ltd.

Mercury capture by selected Bulgarian fly ashes: Influence of coal rank and fly ash carbon pore structure on capture efficiency

Energy Technology Data Exchange (ETDEWEB)

Kostova, I.J.; Hower, J.C.; Mastalerz, M.; Vassilev, S.V. [University of Kentucky, Lexington, KY (United States). Center of Applied Energy Research

2011-01-15

Mercury capture by fly ash C was investigated at five lignite- and subbituminous-coal-burning Bulgarian power plants (Republika, Bobov Dol, Maritza East 2, Maritza East 3, and Sliven). Although the C content of the ashes is low, never exceeding 1.6%, the Hg capture on a unit C basis demonstrates that the low-rank-coal-derived fly ash carbons are more efficient in capturing Hg than fly ash carbons from bituminous-fired power plants. While some low-C and low-Hg fly ashes do not reveal any trends of Hg versus C, the 2nd and, in particular, the 3rd electrostatic precipitator (ESP) rows at the Republika power plant do have sufficient fly ash C range and experience flue gas sufficiently cool to capture measurable amounts of Hg. The Republika 3rd ESP row exhibits an increase in Hg with increasing C, as observed in other power plants, for example, in Kentucky power plants burning Appalachian-sourced bituminous coals. Mercury/C decreases with an increase in fly ash C, suggesting that some of the C is isolated from the flue gas stream and does not contribute to Hg capture. Mercury capture increases with an increase in Brunauer-Emmett-Teller (BET) surface area and micropore surface area. The differences in Hg capture between the Bulgarian plants burning low-rank coal and high volatile bituminous-fed Kentucky power plants suggests that the variations in C forms resulting from the combustion of the different ranks also influence the efficiency of Hg capture.

Reuse of Partially Sulphated CFBC Ash as an SO2 Sorbent

Energy Technology Data Exchange (ETDEWEB)

Wu, Yinghai; Jia, Lufei; Anthony, E.J. [CanmetENERGY, 1 Haanel Drive, Ottawa, Ontario, K1A1M1 (Canada); Nobili, M.; Telesca, A. [Department of Environmental Engineering and Physics, University of Basilicata, Viale dell' Ateneo, Lucano 10, 85100 Potenza (Italy); Montagnaro, F. [Department of Chemistry, University of Naples ' Federico II' , Monte Sant' Angelo, 80126 Naples (Italy)

2010-06-15

Ashes produced from fluidized bed combustors (FBC) burning high-sulphur fuels often contain 20-30 % unreacted CaO because of the limestone added to remove SO2 in situ. This paper presents the results from experiments into reactivating partially sulphated FBC ash (both bed ash and fly ash) with liquid water, steam and sodium carbonate. The water- or steam-hydrated ashes were subsequently re-sulphated in a thermogravimetric analyzer (TGA) with simulated flue gas. The TGA results show that, while liquid water and steam successfully hydrate and reactivate the unreacted CaO in the bed ash, the treated ashes sulphated to widely different extents. Attempts to reactivate fly ash with hydration failed, although fly ash by itself is extremely reactive. A pilot-scale mini-circulating FBC (CFBC) was also used to evaluate the results of reactivation on the bed ash by hydrating with liquid water and admixtures of inorganic salt (Na2CO3) in the form of either powder or solution. When the treated ash was re-injected into the combustor with the fuel, the effect on SO2 removal efficiency was negligible if Na2CO3 was added as powder. Doping with aqueous solution resulted in enhanced SO2 removal; however, the extent was lower than the level achieved if only water hydration was employed. Increasing the amount of water (from 10% to 30%) to reactivate the ash did not improve the sulphur capture capacity in the mini-CFBC. Overall, this study suggests that the most practical way for re-use of the partially sulphated bed ash as a sulphur sorbent is reactivation by water. A proposal for utilization of the fly ash in an economically reasonable way is also discussed.

Effects of the emerald ash borer invasion on the community composition of arthropods associated with ash tree boles

Science.gov (United States)

Emerald ash borer (EAB), Agrilus planipennis Fairmaire is an invasive non-native wood-boring beetle that has killed hundreds of millions of ash trees (Fraxinus spp.) in North America, and threatens to extirpate the ecological services provided by the genus. Identifying the arthropod community assoc...

Improving volcanic ash forecasts with ensemble-based data assimilation

NARCIS (Netherlands)

Fu, Guangliang

2017-01-01

The 2010 Eyjafjallajökull volcano eruption had serious consequences to civil aviation. This has initiated a lot of research on volcanic ash forecasting in recent years. For forecasting the volcanic ash transport after eruption onset, a volcanic ash transport and diffusion model (VATDM) needs to be

Quantification of fusion in ashes from solid fuel combustion

DEFF Research Database (Denmark)

Hansen, Lone Aslaug; Frandsen, Flemming; Dam-Johansen, Kim

1999-01-01

The fusion of ashes produced during solid fuel combustion greatly affects the tendency of these ashes to cause operational problems in utility boilers. In this paper, a new and quantitative laboratory method for assessing the fusion of ashes based on simultaneous thermal analysis, STA, is described...

Anticholinergic, antihistaminic, and antiserotonergic activity of n-hexane extract of Zanthoxylum alatum seeds on isolated tissue preparations: An ex vivo study.

Science.gov (United States)

Saikia, Beenita; Barua, Chandana Choudhury; Haloi, Prakash; Patowary, Pompy

2017-01-01

The aim of this study was to evaluate anticholinergic, antihistaminic, and antiserotonergic activity of the n-hexane extract of the seeds of Zanthoxylum alatum (ZAHE) on isolated ileum of rat and guinea pig and fundus of rat. ZAHE was prepared using soxhlet extraction and cumulative concentration response curves were constructed using various doses on the tissues for acetylcholine (ACh), 5-hydroxytryptamine (5-HT), and histamine with or without n-hexane extract. Atropine, ketanserin, and pheniramine maleate were used as antagonists for ACh, serotonin, and histamine, respectively. ZAHE-induced concentration-dependent inhibition of isolated ileum and fundus in rat and ileum of guinea pig. The half maximal effective concentration (EC 50 ) of ACh in the presence of atropine (10 -6 M; P pheniramine maleate (10 -6 M; P < 0.01) and ZAHE (300 μg/ml; P < 0.01 and 1000 μg/ml; P < 0.05) was also significantly higher than EC 50 of histamine alone. From the study, it was observed that ZAHE shows significant anticholinergic, antiserotonergic, and antihistaminic activity. The study provides sufficient evidence that the seeds can be used in gastric disorders, cough, chest infection, etc., as per folklore claims.

Ash dust co-centration in the vicinity of the ash disposal site depending on the size of the pond (“Water Mirror”

Directory of Open Access Journals (Sweden)

Zoran Gršić

2010-09-01

Full Text Available Thermal power plants Nikola Tesla “A” and “B” are large sources of ash from their ashes/slag deposit sites. Total sizes of ashes/slag depots are 600ha and 382ha, with active cassettes having dimensions ∼200 ha and ∼130 ha. The active cassettes of the disposal sites are covered by rather large waste ponds, the sizes of vary depending on the working condition of a sluice system and on meteorological conditions. Modeling of ash lifting was attempted using results from the dust lifting research. The relation between sizes of ponds and air dust concentration in the vicinity of ash disposal sites was analyzed. As expected, greater sizes of dried disposal site surfaces in combination with stronger winds gave greater dust emission and greater air dust concentration.

Partial oxidation of methane to methanol over catalyst ZSM-5 from coal fly ash and rice husk ash

Directory of Open Access Journals (Sweden)

Mirda Yanti Fusia

2017-01-01

Full Text Available Methane is one of the greenhouse gases that can be converted into liquid fuels such as methanol to retain most of the energy of methane and produce a cleaner environment. The conversion of methane to methanol using ZMS-5 represents a breakthrough in the utilization of methane. However, material sources for zeolite synthesis as catalyst usually are pro-analysis grade materials, which are expensive. Therefore, in this research, coal fly ash and rice husk ash were used as raw materials for mesoporous ZSM-5 zeolite synthesis. First, coal fly ash and rice husk were subjected to pre-treatment to extract silicate (SiO44− and aluminate (AlO45− and impurities separation. The ZSM-5 zeolite was synthesized through hydrothermal treatment using two types of templates. After ZSM-5 was synthesized, it was modified with Cobalt through impregnation method. The catalytic activity of both ZSM-5 and Co/ZSM-5 zeolites as heterogeneous catalysts in partial oxidation of methane were preliminary tested and compared with that commercial one. The result showed that the zeolite catalyst ZSM-5 from fly ash coal and rice husk ash has the potential to be used as catalysts in the partial oxidation of methane to methanol.

Sap flow of black ash in wetland forests of northern Minnesota, USA: Hydrologic implications of tree mortality due to emerald ash borer

Science.gov (United States)

Andrew C. Telander; Robert A. Slesak; Anthony W. D' Amato; Brian J. Palik; Kenneth N. Brooks; Christian F. Lenhart

2015-01-01

Black ash (Fraxinus nigra) mortality caused by the invasive emerald ash borer (EAB) is of concern to land managers in the upper Great Lakes region, given the large areas of ash-dominated forest and potential alteration of wetland hydrology following loss of this foundation tree species. The importance of changes in evapotranspiration (ET) following...

Knowledge of and attitudes toward heel prick screening for sickle cell disease in Saint Lucia.

Science.gov (United States)

Alexander, Sonia; Belmar-George, Sharon; Eugene, Alisha; Elias, Vanessa

2017-06-08

In the Caribbean country of Saint Lucia, umbilical-cord-blood screening for sickle cell disease (SCD) was the testing method that health care workers (HCWs) on the maternity wards of the hospitals preferred until the new heel prick (HP) testing method was introduced in the country in 2014. This SCD study sought to assess HCWs' knowledge of and attitude toward HP screening and also determine new mothers' favorability toward HP screening. A total of 70 HCWs and 132 new mothers answered survey questionnaires in three hospitals. In addition, four focus group discussions were held, two with HCWs and two with the mothers. Among the HCWs interviewed, 85.7% of them had knowledge of the HP test. However, only 25.7% had attended training sessions on the procedure. Among the HCWs, 64.3% of them felt the HP test should be mandatory, 27.1% said it should not be mandatory, and 8.6% did not know if it should be mandatory. In their focus groups, the HCWs said they believed the mothers would accept the HP method. For their part, 22.0% of the mothers said they had heard about the HP test, and 63.6% reported knowing the reason why the baby would be tested. Further, 83.3% indicated that the test would be beneficial for the baby. In addition, 88.6% of the mothers said that more information on the HP test was needed. In their focus group discussions, the mothers said they were generally not concerned about the pain the heel prick method might cause the baby. The HCWs' knowledge of the HP screening method was high. The mothers trust HCWs, and the mothers would accept the HP procedure irrespective of their knowledge of the test and any discomfort associated with this screening method.

Knowledge of and attitudes toward heel prick screening for sickle cell disease in Saint Lucia

Directory of Open Access Journals (Sweden)

Sonia Alexander

2017-06-01

Full Text Available ABSTRACT Objectives In the Caribbean country of Saint Lucia, umbilical-cord-blood screening for sickle cell disease (SCD was the testing method that health care workers (HCWs on the maternity wards of the hospitals preferred until the new heel prick (HP testing method was introduced in the country in 2014. This SCD study sought to assess HCWs’ knowledge of and attitude toward HP screening and also determine new mothers’ favorability toward HP screening. Methods A total of 70 HCWs and 132 new mothers answered survey questionnaires in three hospitals. In addition, four focus group discussions were held, two with HCWs and two with the mothers. Results Among the HCWs interviewed, 85.7% of them had knowledge of the HP test. However, only 25.7% had attended training sessions on the procedure. Among the HCWs, 64.3% of them felt the HP test should be mandatory, 27.1% said it should not be mandatory, and 8.6% did not know if it should be mandatory. In their focus groups, the HCWs said they believed the mothers would accept the HP method. For their part, 22.0% of the mothers said they had heard about the HP test, and 63.6% reported knowing the reason why the baby would be tested. Further, 83.3% indicated that the test would be beneficial for the baby. In addition, 88.6% of the mothers said that more information on the HP test was needed. In their focus group discussions, the mothers said they were generally not concerned about the pain the heel prick method might cause the baby. Conclusions The HCWs’ knowledge of the HP screening method was high. The mothers trust HCWs, and the mothers would accept the HP procedure irrespective of their knowledge of the test and any discomfort associated with this screening method.

Interactive influence of leaf age, light intensity, and girdling on green ash foliar chemistry and emerald ash borer development.

Science.gov (United States)

Chen, Yigen; Poland, Therese M

2009-07-01

Biotic and abiotic environmental factors affect plant nutritional quality and defensive compounds that confer plant resistance to herbivory. Influence of leaf age, light availability, and girdling on foliar nutrition and defense of green ash (Fraxinus pennsylvanica Marsh) was examined in this study. Longevity of the emerald ash borer, Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), adults reared on green ash foliage subjected to these factors was assayed. Mature leaves generally were more nutritious with greater amino acids and a greater ratio of protein to non-structural carbohydrate (P:C) than young leaves, in particular when trees were grown in shade. On the other hand, mature leaves had lower amounts of trypsin and chymotrypsin inhibitors, and total phenolics compared to young leaves. Lower defense of mature leaves alone, or along with higher nutritional quality may lead to increased survival and longevity of emerald ash borer feeding on mature leaves. Sunlight reduced amino acids and P:C ratio, irrespective of leaf age and girdling, and elevated total protein of young foliage, but not protein of mature leaves. Sunlight also dramatically increased all investigated defensive compounds of young, but not mature leaves. Girdling reduced green ash foliar nutrition, especially, of young leaves grown in shade and of mature leaves grown in sun. However emerald ash borer performance did not differ when fed leaves from trees grown in sun or shade, or from girdled or control trees. One explanation is that emerald ash borer reared on lower nutritional quality food may compensate for nutrient deficiency by increasing its consumption rate. The strong interactions among leaf age, light intensity, and girdling on nutrition and defense highlight the need for caution when interpreting data without considering possible interactions.

Temporal evolution of wildfire ash and its implications for water pollution

Science.gov (United States)

Santin, Cristina; Doerr, Stefan H.; Otero, Xose L.; Chafer, Chris J.

2015-04-01

Ash, the burnt residue generated from combustion of vegetation, litter and surface soil, covers the ground after every wildfire. The effects of wildfire ash on the post-fire landscape are many and very diverse. It is a source of nutrients and can, therefore, help the recovery of vegetation after fire. Furthermore, in its initial state, the ash layer on the ground can protect the bare soil from rain splash erosion and can act as an adsorbent layer, preventing or delaying post-fire water erosion by runoff. However, when the adsorbent capability of the ash layer is exceeded, this highly erodible material can be transported into the hydrological network and be a major contributor to water contamination. Most previous studies on post-fire erosion and water contamination have focused on soil erosion and associated sediment transfer and overlooked the ash component or, when considered, ash has been included as an unidentified part of the eroded sediment. One of the reasons for overlooking this key post-fire component is the difficulty of ash sampling before it is lost by wind or water erosion or altered by aging on-site. Here we compare the water contamination potential of ash obtained from two fires in the dry eucalyptus forest environment of the Sydney tablelands, Australia: i) 'aged ash' produced during the severe Balmoral wildfire and sampled two months after the event (Jan. 2014) and ii) 'fresh ash' sampled immediately after a high-intensity experimental fire in the same region (Sept. 2014). At the time of sampling, neither of the ash types had been affected by water erosion, however, the aged ash had been subjected to rainfall events and, potentially, to wind erosion during the two months of exposure. Vegetation type, fuel loads and fire severity, determined using remote sensing and on-site observations, were comparable between both areas sampled. Ash physicochemical properties differed, with 'fresh ash' having higher pH and EC values and higher concentration of

Incineration ashes conditioning by isostatic pressing and melting

International Nuclear Information System (INIS)

Jouan, A.; Ouvrier, N.; Teulon, F.

1990-01-01

Alpha-bearing solid incineration wastes are conditioned for two principal reasons: to enhance the quality of the finished product for long-term storage, and to reduce the total waste volume. Isostatic pressing parameters were defined using containers 36 mm in diameter; the physicochemical properties of the compacted ashes were determined with 140 mm diameter containers and industrial feasibility was demonstrated with a large (300 mm diameter) container. Two types of ashes were used: ashes fabricated at Marcoule (either in devices developed by the CEA for the MELOX project with a standard MELOX composition, or by direct incineration at COGEMA's UP1 plant) and fly ash from a domestic waste incinerator. A major engineering study was also undertaken to compare the three known ash containment processes: isostatic pressing, melting, and cement-resin matrix embedding. The flowsheet, operational chronology and control principles were detailed for each process, and a typical plant layout was defined to allow comparisons of both investment and operating costs

Managing ash from the combustion of solid waste

International Nuclear Information System (INIS)

Hauser, R.

1992-01-01

This paper reports that with millions of tons of refuse being combusted each year, increasing concern over the environment impact of the residue produced has caused both regulators and the resource recovery industry to address the technical and regulatory issues relating to the safe handling and disposal of ash. The basic issue concerning solid waste combustion ash management in this country is how, based on past, recent, and ongoing scientific research, solid waste combustion ash should be handled. Typically, refuse contains approximately 20 to 25 percent residue, which is collected either on grates at the bottom of the combustion chamber or filtered from the exhaust gases by the air pollution control equipment. The fly ash component of the total residue stream is between 10 and 30 percent of the total residue while the bottom ash content ranges from 70 to 90 percent of the total weight, depending upon the air pollution control equipment utilized, especially acid gas scrubbing equipment

Aggregate material formulated with MSWI bottom ash and APC fly ash for use as secondary building material.

Science.gov (United States)

del Valle-Zermeño, R; Formosa, J; Chimenos, J M; Martínez, M; Fernández, A I

2013-03-01

The main goal of this paper is to obtain a granular material formulated with Municipal Solid Waste Incineration (MSWI) bottom ash (BA) and air pollution control (APC) fly ash to be used as secondary building material. Previously, an optimum concrete mixture using both MSWI residues as aggregates was formulated. A compromise between the environmental behavior whilst maximizing the reuse of APC fly ash was considered and assessed. Unconfined compressive strength and abrasion resistance values were measured in order to evaluate the mechanical properties. From these results, the granular mixture was not suited for certain applications owing to the high BA/APC fly ash content and low cement percentages used to reduce the costs of the final product. Nevertheless, the leaching test performed showed that the concentrations of all heavy metals were below the limits established by the current Catalan legislation for their reutilization. Therefore, the material studied might be mainly used in embankments, where high mechanical properties are not needed and environmental safety is assured. Copyright © 2012 Elsevier Ltd. All rights reserved.

Evaluation of the mechanical properties of class-F fly ash

Energy Technology Data Exchange (ETDEWEB)

Kim, B.; Prezzi, M. [Purdue University, West Lafayette, IN (United States)

2008-07-01

Coal-burning power plants in the United States (US) generate more than 70 million tons of fly ash as a by-product annually. Recycling large volumes of fly ash in geotechnical applications may offer an attractive alternative to the disposal problem as most of it is currently dumped in ponds or landfills. Class-F fly ash, resulting from burning of bituminous or anthracite coals, is the most common type of fly ash in the US. In the present study, the mechanical characteristics (compaction response, compressibility, and shear strength) of class-F fly ash were investigated by performing various laboratory tests (compaction test, one-dimensional compression test, direct shear test and consolidated-drained triaxial compression test) on fly ash samples collected from three power plants in the state of Indiana (US). Test results have shown that despite some morphological differences, class-F fly ash exhibits mechanical properties that are, in general, comparable to those observed in natural sandy soils.

KINETICS OF FLY ASH BENEFICIATION BY CARBON BURNOUT

Energy Technology Data Exchange (ETDEWEB)

Dr. Joseph N.D. Dodoo; Dr. Joseph M. Okoh

2000-11-01

Surface area analyses performed on fly ash samples reveal that the surface area is controlled by carbon content. The higher surface areas found in large particles are due to the presence of highly porous carbonaceous particles. Adsorption-desorption isotherms and t-plots of fly ash samples indicate that fly ash is porous. BJH Adsorption/Desorption pore size analysis reveal that pore diameters are independent of sieve size. They appear to be dependent only on the nature of the material which confers porosity. Based on the results of Brown and Dykstra (41) it is reasonable to assume that calculations of reaction rates at temperatures above 550 C were confounded by weight losses from processes other than carbon oxidation and, therefore, are not useful in determination of the temperature dependence of carbon oxidation in fly ash. The results of the present study indicate that temperatures below 550 C should be used for future studies in order to satisfactorily assess the temperature dependence of carbon oxidation in fly ash. Furthermore, it is also advisable that percent carbon determinations be performed on fly ash samples after the oxidation reactions to determine whether all carbon present in fly ash is oxidized. This will ensure that reaction rates are representative of the complete oxidation of carbon. An inverse relationship was determined between reaction rates and oxygen concentration for this study. As discussed, this may be due to volatilization of volatiles from fly ash and ease of transport of products away from the reaction sites by the action of the vacuum applied to the samples. A more accurate determination of oxygen dependence of carbon oxidation can be accomplished by the use of specialty gases containing different concentrations of oxygen which could eliminate the need to apply vacuum to the samples.

The aggregation efficiency of very fine volcanic ash

Science.gov (United States)

Del Bello, E.; Taddeucci, J.; Scarlato, P.

2013-12-01

Explosive volcanic eruptions can discharge large amounts of very small sized pyroclasts (under 0.090 mm) into the atmosphere that may cause problems to people, infrastructures and environment. The transport and deposition of fine ash are ruled by aggregation that causes premature settling of fine ash and, as consequence, significantly reduces the concentration of airborne material over long distances. Parameterizing the aggregation potential of fine ash is then needed to provide accurate modelling of ash transport and deposition from volcanic plumes. Here we present the first results of laboratory experiments investigating the aggregation efficiency of very fine volcanic particles. Previous laboratory experiments have shown that collision kinetic and relative humidity provide the strongest effect on aggregation behaviour but were only limited to particles with size > 0.125 mm. In our work, we focus on natural volcanic ash at ambient humidity with particles size aggregation potential. Two types of ash were used in our experiments: fresh ash, collected during fall-out from a recent plume-forming eruption at Sakurajima (Japan -July 2013) and old ash, collected from fall-out tephra deposits at Campi Flegrei (Italy, ca. 10 ka), to account for the different chemical composition and morphoscopic effects of altered ash on aggregation efficiency. Total samples were hand sieved to obtain three classes with unimodal grain size distributions (sieved from the top of a transparent tank where a fan, placed at the bottom, allows turbulent dispersion of particles. Collision and sticking of particles on a vertical glass slide were filmed with a high speed cameras at 6000 fps. Our lenses arrangement provide high image resolution allowing to capture particles down to 0.005 mm in diameter. Video sequences of particles motion and collision were then processed with image analysis and particle tracking tools to determine i) the particle number density and ii) the grain size distribution

Magmatic and fragmentation controls on volcanic ash surface chemistry

Science.gov (United States)

Ayris, Paul M.; Diplas, Spyros; Damby, David E.; Hornby, Adrian J.; Cimarelli, Corrado; Delmelle, Pierre; Scheu, Bettina; Dingwell, Donald B.

2016-04-01

The chemical effects of silicate ash ejected by explosive volcanic eruptions on environmental systems are fundamentally mediated by ash particle surfaces. Ash surfaces are a composite product of magmatic properties and fragmentation mechanisms, as well as in-plume and atmospheric alteration processes acting upon those surfaces during and after the eruption. Recent attention has focused on the capacity of alteration processes to shape ash surfaces; most notably, several studies have utilised X-ray photoelectron spectroscopy (XPS), a technique probing the elemental composition and coordination state of atoms within the top 10 nm of ash surfaces, to identify patterns of elemental depletions and enrichments relative to bulk ash chemical composition. Under the presumption of surface and bulk equivalence, any disparities have been previously attributed to surface alteration processes, but the ubiquity of some depletions (e.g., Ca, Fe) across multiple ash studies, irrespective of eruptive origin, could suggest these to be features of the surface produced at the instant of magma fragmentation. To investigate this possibility further, we conducted rapid decompression experiments at different pressure conditions and at ambient and magmatic temperature on porous andesitic rocks. These experiments produced fragmented ash material untouched by secondary alteration, which were compared to particles produced by crushing of large clasts from the same experiments. We investigated a restricted size fraction (63-90 μm) from both fragmented and crushed materials, determining bulk chemistry and mineralogy via XRF, SEM-BSE and EPMA, and investigated the chemical composition of the ash surface by XPS. Analyses suggest that fragmentation under experimental conditions partitioned a greater fraction of plagioclase-rich particles into the selected size fraction, relative to particles produced by crushing. Trends in surface chemical composition in fragmented and crushed particles mirror that

Greenlandic Waste Incineration Fly And Bottom Ash As Secondary Resource In Mortar

DEFF Research Database (Denmark)

Kirkelund, Gunvor Marie; Ottosen, Lisbeth M.; Jensen, Pernille Erland

2016-01-01

Today, 900 tons incineration fly ash is shipped abroad annually from Greenland for deposits, whereas the 6,000 tons incineration bottom ash is deposited locally. These incineration ashes could be valuable in concrete production, where the cement has to be shipped to Greenland. For this purpose...... and cement with fly ash. Based on the compressive strength tests, it is found that using Greenlandic incineration ashes in mortar as 5% cement replacement could consume all ash instead of disposals, and could thus turn the ashes into a local resource and simultaneously reduce the import of cement....

Effects of cutting time, stump height, and herbicide application on ash (Fraxinus spp.) stump sprouting and colonization by emerald ash borer (Agrilus planipennis)

Science.gov (United States)

Toby R. Petrice; Robert A. Haack

2011-01-01

Efforts to eradicate or slow the spread of emerald ash borer (EAB) (Agrilus planipennis Fairmaire [Coleoptera: Buprestidae]) include cutting infested and nearby uninfested ash (Fraxinus spp.) trees. However, ash trees readily sprout after they have been cut, providing potential host material for EAB. In 2004-2005, we conducted...

Characterization of ash in algae and other materials by determination of wet acid indigestible ash and microscopic examination

Science.gov (United States)

Algae are known for high ash content. It is important to properly characterize their ash for value added utilization of algae as food, feed, and feedstock for biofuels. In this study, 12 algae of different sources were measured for proximate composition and mineral profile. Results showed that the r...

Rheology of fly ashes from coal and biomass co-combustion

DEFF Research Database (Denmark)

Arvelakis, Stelios; Frandsen, Flemming

2010-01-01

The presence of large amounts of alkali metals, chlorine and sulphur in most biomass fuels - compared to coal - can create serious ash-related problems such as deposition, agglomeration and/or corrosion. This paper discusses the viscosity characteristics of fly ash from the co-combustion of various...... coal/biomass blends in a pilot scale pf-boiler. The produced data provide information on the melting of the ash and its flow characteristics, as a function of temperature, which may be used to modify the temperature profile of the boiler in order to avoid slagging. Straw co-firing lowers the ash...... viscosity leading to higher stickiness of the ash particles. Wood co-firing has only minor effects, due to the composition of wood ash and the low percentage of wood in the coal/biomass blend....

Genetic transformation of Fraxinus spp. for resistance to the emerald ash borer

Science.gov (United States)

Paula M. Pijut; Rochelle R. Beasley; Kaitlin J. Palla

2010-01-01

The emerald ash borer (EAB; Agrilus planipennis Fairmaire) (Coleoptera; Buprestidae) is a wood-boring beetle that poses substantial risk to the ash resource in North America. Ash species native to the United States and known to be susceptible to EAB are Fraxinus pennsylvanica (green ash), F. americana (white ash...

Mutagenicity and genotoxicity of coal fly ash water leachate.

Science.gov (United States)

Chakraborty, Rajarshi; Mukherjee, Anita

2009-03-01

Fly ash is a by-product of coal-fired electricity generation plants. The prevalent practice of disposal is as slurry of ash and water to storage or ash ponds located near power stations. This has lain to waste thousands of hectares of land all over the world. Since leaching is often the cause of off-site contamination and pathway of introduction into the human environment, a study on the genotoxic effects of fly ash leachate is essential. Leachate prepared from the fly ash sample was analyzed for metal content, and tested for mutagenicity and genotoxicity. Analyses of metals show predominance of the metals-sodium, silicon, potassium, calcium, magnesium, iron, manganese, zinc, and sulphate. The Ames Salmonella mutagenicity assay, a short-term bacterial reverse mutation assay, was conducted on two-tester strains of Salmonella typhimurium strains TA97a and TA102. For genotoxicity, the alkaline version of comet assay on fly ash leachate was carried in vitro on human blood cells and in vivo on Nicotiana plants. The leachate was directly mutagenic and induced significant (Ppercentage (%), tail length (mum), and olive tail moment (arbitrary units). Our results indicate that leachate from fly ash dumpsites has the genotoxic potential and may lead to adverse effects on vegetation and on the health of exposed human populations.

Size distribution of rare earth elements in coal ash

Science.gov (United States)

Scott, Clinton T.; Deonarine, Amrika; Kolker, Allan; Adams, Monique; Holland, James F.

2015-01-01

Rare earth elements (REEs) are utilized in various applications that are vital to the automotive, petrochemical, medical, and information technology industries. As world demand for REEs increases, critical shortages are expected. Due to the retention of REEs during coal combustion, coal fly ash is increasingly considered a potential resource. Previous studies have demonstrated that coal fly ash is variably enriched in REEs relative to feed coal (e.g, Seredin and Dai, 2012) and that enrichment increases with decreasing size fractions (Blissett et al., 2014). In order to further explore the REE resource potential of coal ash, and determine the partitioning behavior of REE as a function of grain size, we studied whole coal and fly ash size-fractions collected from three U.S commercial-scale coal-fired generating stations burning Appalachian or Powder River Basin coal. Whole fly ash was separated into , 5 um, to 5 to 10 um and 10 to 100 um particle size fractions by mechanical shaking using trace-metal clean procedures. In these samples REE enrichments in whole fly ash ranges 5.6 to 18.5 times that of feedcoals. Partitioning results for size separates relative to whole coal and whole fly ash will also be reported. 

Coal combustion ashes: A radioactive Waste?

International Nuclear Information System (INIS)

Michetti, F.P.; Tocci, M.

1992-01-01

The radioactive substances naturally hold in fossil fuels, such as Uranium and Thorium, after the combustion, are subjected to an increase of concentration in the residual combustion products as flying ashes or as firebox ashes. A significant percentage of the waste should be classified as radioactive waste, while the political strategies seems to be setted to declassify it as non-radioactive waste. (Author)

Fly ash. Quality recycling material

Energy Technology Data Exchange (ETDEWEB)

Blomster, D.; Leisio, C.

1996-11-01

Imatran Voima`s coal-fired power plants not only generate power and heat but also produce fly ash which is suitable raw material for recycling. This material for recycling is produced in the flue gas cleaning process. It is economical and, thanks to close quality control, is suitable for use as a raw material in the building materials industry, in asphalt production, and in earthworks. Structures made from fly ash are also safe from an environmental point of view. (orig.)

Mapping ash properties using principal components analysis

Science.gov (United States)

Pereira, Paulo; Brevik, Eric; Cerda, Artemi; Ubeda, Xavier; Novara, Agata; Francos, Marcos; Rodrigo-Comino, Jesus; Bogunovic, Igor; Khaledian, Yones

2017-04-01

In post-fire environments ash has important benefits for soils, such as protection and source of nutrients, crucial for vegetation recuperation (Jordan et al., 2016; Pereira et al., 2015a; 2016a,b). The thickness and distribution of ash are fundamental aspects for soil protection (Cerdà and Doerr, 2008; Pereira et al., 2015b) and the severity at which was produced is important for the type and amount of elements that is released in soil solution (Bodi et al., 2014). Ash is very mobile material, and it is important were it will be deposited. Until the first rainfalls are is very mobile. After it, bind in the soil surface and is harder to erode. Mapping ash properties in the immediate period after fire is complex, since it is constantly moving (Pereira et al., 2015b). However, is an important task, since according the amount and type of ash produced we can identify the degree of soil protection and the nutrients that will be dissolved. The objective of this work is to apply to map ash properties (CaCO3, pH, and select extractable elements) using a principal component analysis (PCA) in the immediate period after the fire. Four days after the fire we established a grid in a 9x27 m area and took ash samples every 3 meters for a total of 40 sampling points (Pereira et al., 2017). The PCA identified 5 different factors. Factor 1 identified high loadings in electrical conductivity, calcium, and magnesium and negative with aluminum and iron, while Factor 3 had high positive loadings in total phosphorous and silica. Factor 3 showed high positive loadings in sodium and potassium, factor 4 high negative loadings in CaCO3 and pH, and factor 5 high loadings in sodium and potassium. The experimental variograms of the extracted factors showed that the Gaussian model was the most precise to model factor 1, the linear to model factor 2 and the wave hole effect to model factor 3, 4 and 5. The maps produced confirm the patternd observed in the experimental variograms. Factor 1 and 2

Wood ash to treat sewage sludge for agricultural use

Energy Technology Data Exchange (ETDEWEB)

White, R.K. [Clemson Univ., SC (United States)

1993-12-31

About 90% of the three million tons of wood ash generated in the United States from wood burning facilities is being landfilled. Many landfills are initiated tipping fees and/or restrictions on the disposal of special wastes such as ash. The purpose of this work was to evaluate (1) the feasibility of using wood ash to stabilize sewage sludge and (2) the fertilizer and liming value of the sludge/ash mixture on plant response and soil pH. Research showed that wood ash, when mixed with sludge, will produce a pH above 12.0, which meets US EPA criteria for pathogen reduction for land application on non-direct food chain crops. Different ratios of wood ash to sludge mixtures were tested and the 1:1 ratio (by weight) was found to be optimal. Five replications of wood ash from four sources were tested for moisture content, pH and fertilizer nutrients. The pH of the ash/sludge mixture (1:1) on day one ranged from 12.4 to 13.2. In most cases the pH remained the same over a 21 day test or only dropped 0.1 to 0.3 units. Analyses of the mixtures showed that heavy metal concentrations (As, B, Cd, Co, Cr, Cu, Mn, Mo, Ni, Pb, S, Se, Zn) were low. The 1:1 ash/sludge mixture had a calcium carbonate equivalency of 17%. Green house pot studies using tall fescue grass were loadings of 300 to 750 pounds per acre of TKN-N than for 500 lb/acre of 10-10-10 commercial fertilizer. Plant tissue analysis showed N, P, K, Ca, and Mg levels to be within the sufficiency range for tall fescue.

Effect of municipal solid waste ash on comprehensive strength ...

African Journals Online (AJOL)

The blocks were moulded in a CINVA-Ram machine by replacing 0%, 2%, 5% and 10% of municipal solid waste ash (MSW ash) as a stabilizing agent. The compressive strengths of individual blocks were obtained after curing for 7, 14 and 28 days. The 2%MSW ash replacement gave the highest compressive strength and ...

Characterization of fly ash from bio and municipal waste

DEFF Research Database (Denmark)

Lima, Ana T.; Ottosen, Lisbeth M.; Pedersen, Anne Juul

2008-01-01

the co-combustion of wood and oil. The focus is laid on differences in ash characteristics and on the mobility of Cd and Cr. These two heavy metals are chosen because Cd is the problematic heavy metal in bio ashes and Cr is problematic in many ash stabilization methods (in the Cr(VI) state). Based...

Heavy metals in MSW incineration fly ashes

DEFF Research Database (Denmark)

Ferreira, Celia; Ribeiro, Alexandra B.; Ottosen, Lisbeth M.

2003-01-01

Incineration is a common solution for dealing with the increasing amount of municipal solid waste (MSW). During the process, the heavy metals initially present in the waste go through several transformations, ending up in combustion products, such as fly ash. This article deals with some issues...... related to the combustion of MSW and the formation of fly ash, especially in what concerns heavy metals. Treatment of the flue gas in air pollution control equipment plays an important role and the basic processes to accomplish this are explained. Fly ash from a semi-dry flue gas treatment system...

Effect of mechanical activation of fly ash added to Moroccan Portland cement

Directory of Open Access Journals (Sweden)

Ez-zaki H.

2018-01-01

This study aims to investigate the influence of grinding fly ash on the physico-chemical and mechanical properties of fly ash blended CPJ45 cement. The addition of the fly ash particles to the grinder leads respectively to the breakage of the particles and to reduce the agglomeration effect in the balls of cement grinder. Fly ash milling was found to improve particles fineness, and increase the silica and alumina content in the cement. Furthermore, milled fly ash blended cements show higher compressive strength compared to unmilled fly ash blended cements, due to improved fly ash reactivity through their mechanical activation.

Influence of fly-ashes on properties of ordinary concretes

Directory of Open Access Journals (Sweden)

Rutkowska Gabriela

2016-03-01

Full Text Available Influence of fly-ashes on properties of ordinary concretes. Care of the environment in accordance with the principles of sustainable development introduces the possibility and need for waste recycling. The construction and building materials industry has the greatest potential for reuse of waste. The article presents the results of investigations of selected properties (consistency, water absorbability, compressive strength and tensile strength after 28 and 56 days of curing, depth of penetration of ordinary concretes and concretes containing fly-ashes - calcareous and siliceous ash − in their composition. To make the samples, the Portland cement CEM I 42.5 R and natural aggregate with graining of 0-16 mm were used. The concrete with siliceous and calcareous admixtures was made in three lots where the ash was added in the quantity of 15, 20 and 30% of the cement mass. After the tests, it was stated that the fly-ash admixture does not increase the air content in the mix, it increases the compressive strength in time and the siliceous ash improves the splitting tensile strength.

Ash Reduction of Corn Stover by Mild Hydrothermal Preprocessing

Energy Technology Data Exchange (ETDEWEB)

M. Toufiq Reza; Rachel Emerson; M. Helal Uddin; Garold Gresham; Charles J. Coronella

2014-04-22

Lignocellulosic biomass such as corn stover can contain high ash content, which may act as an inhibitor in downstream conversion processes. Most of the structural ash in biomass is located in the cross-linked structure of lignin, which is mildly reactive in basic solutions. Four organic acids (formic, oxalic, tartaric, and citric) were evaluated for effectiveness in ash reduction, with limited success. Because of sodium citrate’s chelating and basic characteristics, it is effective in ash removal. More than 75 % of structural and 85 % of whole ash was removed from the biomass by treatment with 0.1 g of sodium citrate per gram of biomass at 130 °C and 2.7 bar. FTIR, fiber analysis, and chemical analyses show that cellulose and hemicellulose were unaffected by the treatment. ICP–AES showed that all inorganics measured were reduced within the biomass feedstock, except sodium due to the addition of Na through the treatment. Sodium citrate addition to the preconversion process of corn stover is an effective way to reduced physiological ash content of the feedstock without negatively impacting carbohydrate and lignin content.

Corrosion of Modified Concrete with Sugar Cane Bagasse Ash

Directory of Open Access Journals (Sweden)

R. E. Núñez-Jaquez

2012-01-01

Full Text Available Concrete is a porous material and the ingress of water, oxygen, and aggressive ions, such as chlorides, can cause the passive layer on reinforced steel to break down. Additives, such as fly ash, microsilica, rice husk ash, and cane sugar bagasse ash, have a size breakdown that allows the reduction of concrete pore size and, consequently, may reduce the corrosion process. The objective of this work is to determine the corrosion rate of steel in reinforced concrete by the addition of 20% sugar cane bagasse ash by weight of cement. Six prismatic specimens (7×7×10 cm with an embedded steel rod were prepared. Three contained 20% sugar cane bagasse ash by weight of cement and the other three did not. All specimens were placed in a 3.5% NaCl solution and the corrosion rate was determined using polarization resistance. The results showed that reinforced concrete containing sugar cane bagasse ash has the lowest corrosion rates in comparison to reinforced concrete without the additive.

Chemical Composition and Insecticidal Activity of Essential Oils from Zanthoxylum dissitum Leaves and Roots against Three Species of Storage Pests.

Science.gov (United States)

Wang, Cheng-Fang; Yang, Kai; You, Chun-Xue; Zhang, Wen-Juan; Guo, Shan-Shan; Geng, Zhu-Feng; Du, Shu-Shan; Wang, Yong-Yan

2015-05-04

This work aimed to investigate chemical composition of essential oils obtained from Zanthoxylum dissitum leaves and roots and their insecticidal activities against several stored product pests, namely the cigarette beetle (Lasioderma serricorne), red flour beetle (Tribolium castaneum) and black carpet beetle (Attagenus piceus). The analysis by GC-MS of the essential oils allowed the identification of 28 and 22 components, respectively. It was found that sesquiterpenoids comprised a fairly high portion of the two essential oils, with percentages of 74.0% and 80.9% in the leaves and roots, respectively. The main constituents identified in the essential oil of Z. dissitum leaves were δ-cadinol (12.8%), caryophyllene (12.7%), β-cubebene (7.9%), 4-terpineol (7.5%) and germacrene D-4-ol (5.7%), while humulene epoxide II (29.4%), caryophyllene oxide (24.0%), diepicedrene-1-oxide (10.7%) and Z,Z,Z-1,5,9,9-tetramethyl-1,4,7-cycloundecatriene (8.7%) were the major components in the essential oil of Z. dissitum roots. The insecticidal activity results indicated that the essential oil of Z. dissitum roots exhibited moderate contact toxicity against three species of storage pests, L. serricorne,T. castaneum and A. piceus, with LD50 values of 13.8, 43.7 and 96.8 µg/adult, respectively.

Utilization technology on slurried ash

Energy Technology Data Exchange (ETDEWEB)

Kanbe, Yoshio; Yasuda, Minoru; Furuki, Yasuhiko [The Coal Mining Research Centre, Japan, Tokyo, Japan; Electric Power Development Co., Ltd., Tokyo (Japan))

1987-08-01

Three research results of the utilization technology on slurried ash were reported. As for the utilization as the fly ash quick setting (FQS) backfill grout for tail void in shield works of tunneling, grout blending was simplified, the blended solution of cement, clay, additives and water was stabilized, and a favorable workability and long term durability were obtained. As for the utilization as the material of a SMW (soil mixing wall) method for continuous walls in long shaft digging, a fly ash-gypsum-cement (FGC) stabilizer showed an excellent workability and remarkably high water-tightness as compared with conventional cement bentonite. As for the utilization as the material of an injection method of overlay mats in foundation works of light weight structures on the sea bed mud foundation, since a FGC concrete weight in water was remarkably light as 0.7t/m{sup 3}, no both large mold form strength and vibration compacting were required. 10 figs., 8 tabs.

Producing zeolites from fly ash

International Nuclear Information System (INIS)

Rayalu, S.; Labhestwar, N.K.; Biniwale, R.B.; Udhoji, J.S.; Meshram, S.U.; Khanna, P.

1998-01-01

Fly ash has virtually become a menace of thermal power generation, leading to its devastating effects on the environment. Development of alternate methods of its disposal - especially those with recourse to recovery of valuable materials-has thus become imperative. This paper deals with the utilisation of fly ash for the production of high value-added products, viz., commercial grade zeolites. The physico-chemical and morphological characteristics of fly ash based Zeolite-A (FAZ-A) compares well with commercial Zeolite-A. High calcium binding capacity, appropriate particle/pore size and other detergency characteristics of FAZ-A brings forth its potential as a substitute for phosphatic detergent builder. The technology is extremely versatile, and other products like Zeolite-X, Zeolite-Y, sodalite and mordenite are also amenable for cost effective production with modifications in certain reaction parameters. Low temperature operations, ready availability of major raw materials, simplicity of process and recycling of unused reactants and process water are special features of the process. (author)

Ashes from biofuels and mixed fuels - amount and qualities

International Nuclear Information System (INIS)

Bjurstroem, Henrik; Ilskog, Elisabeth; Berg, Magnus

2003-04-01

In this study, ashes from biofuels used in the energy utilities, the pulp and paper industry and the wood-working industries have been inventoried. The selection of plants to which enquiries were addressed consists of about 50 utilities, all pulp and paper plants and about 20 wood-working industries (e.g. sawmills). The purpose of the study was to estimate the quantities of bio ashes that are recycled to the forests and those that could be recycled. The background to this study is that logging slash is harvested from ca 30,000 ha per year, while ash is recycled only to 2 to 4,000 ha per year. A working hypothesis has been that logging slash or clean wooden fuels are mixed with other fuels to such an extent that the ash is too contaminated to be recycled. The consequence would be that there is a shortage of suitable ash. Therefore, it was desirable that motives for mixing fuels be chartered. In Sweden, approximately one million ton ashes are produced each year and the share of the three industries that have been studied is estimated as: 200 - 340,000 tons from utilities about 275,000 tons from the pulp and paper industry and 100,000 tons from the woodworking industry. These quantities include unburned carbon, water added when the ash is extracted from the boilers etc. Additional quantities of ash are those produced by waste combustion (447,000 tons), wood-burning in residential buildings (50 - 100,000 tons) etc. In all, ash that may be recycled should total about 300,000 tons (Recyclable ash in t/a: Utilities - 80,000; Pulp and Paper Industry - 100-130,000; Woodworking Industry 100,000). Logging slash is seldom burned alone in the boilers at the utilities, but are almost always mixed with other wood fuel fractions such as waste from sawmills. The mixtures can be very complex. Clean mixtures of wood fuel fractions represent ca 4,500 GWh of the ca 7,800 GWh in this study. Other fuels that are often used in mixtures are peat and Salix, which does not necessarily lead

Utilization of ash fractions from alternative biofuels used in power plants

Energy Technology Data Exchange (ETDEWEB)

Nikolaisen, L.; Hinge, J.; Christensen, I. (Danish Technological Inst., Aarhus (Denmark)); Dahl, J. (Force Technology, Broendby (Denmark)); Arendt Jensen, P. (DTU-CHEC, Kgs. Lyngby (Denmark)); Soendergaard Birkmose, T. (Dansk Landbrugsraadgivning, Landscentret, Aarhus (Denmark)); Sander, B. (DONG Energy, Fredericia (Denmark)); Kristensen, O. (Kommunekemi A/S, Nyborg (Denmark))

2008-07-15

It is expected, that demand for the traditional biomass resources wood and straw will increase over the next years. In other projects a number of agro industrial waste products has been tested and characterized as fuels for power plants. The annual production in Denmark of these fuels is estimated at roughly 400.000 tons of Dry Matter per year, so the potential is substantial. The agro industrial biomass products include: Grain screening waste, pea shells, soy waste, cocoa waste, sugar beet waste, sunflower waste, shea waste, coffee waste, olive waste, rice shell waste, potato waste, pectin waste, carrageen waste, tobacco waste, rape seed waste and mash from breweries. In the PSO project 5075, 5 different types of fuel pellets was produced, which were rendered suitable for combustion in power plants. In this project, ash is produced from the above mentioned 5 mixtures together with another 2 mixtures produced especially for this project. From the 5 mixtures from PSO 5075, ash is produced at Danish Technological Institute's slag analyzer. These ash products are rendered comparable to ash from grate fired boilers at power plants. The ash/slag from the combustion in the slag analyzer was then grinded - thus resulting in a total of 5 ash products. At DTU CHEC's Entrained Flow Reactor, ash products from the 5+2 mixtures were produced. These ash products are rendered comparable to ash produced form suspension fired boilers at power plants. For each of the 7 mixtures, bottom-, cyclone and filter ash was taken out separately resulting in a total of 21 ash samples. The produced ashes have been evaluated for their properties as directly applied fertilizer. Furthermore, scenarios have been set up to assess the feasibility in producing artificial fertilizer from the ash products, based on known processes. In the main components the content of Na, S, Cl and K is significantly higher in filter ashes, whereas the content of Mg, Al, Si and Ca is significantly lower. The