WorldWideScience

Sample records for previous high-pressure studies

  1. High pressure studies of molecular lumenescence

    Energy Technology Data Exchange (ETDEWEB)

    Drickamer, H.G.

    1982-01-01

    The studies of high pressure molecular luminescence reviewed, along with results for inorganic systems discussed elsewhere, provide evidence about the versatility and power of high pressure as a tool for characterizing electronic states, testing theories concerning electronic phenomena, and generally obtaining a better understanding of electronic behavior in condensed systems. 16 figures.

  2. High pressure structural studies of conjugated molecules

    DEFF Research Database (Denmark)

    Knaapila, Matti; Torkkeli, Mika; Scherf, Ullrich

    2018-01-01

    This chapter highlights high pressure GPa level structural studies of conjugated polymers and their analogues: conjugated oligomers and molecules, and rigid rod polymers. Attention is placed on our recent studies of polyfluorenes.......This chapter highlights high pressure GPa level structural studies of conjugated polymers and their analogues: conjugated oligomers and molecules, and rigid rod polymers. Attention is placed on our recent studies of polyfluorenes....

  3. Recent high pressure photoluminescence studies

    Energy Technology Data Exchange (ETDEWEB)

    Drickamer, H.G.; Lang, J.M.; Dreger, Z.A. (Department of Chemical Engineering, University of Illinois, 1209 W. California Street, Urbana, Illinois 61801 (United States))

    1994-07-10

    In this paper we discuss two studies involving the effect of pressure on luminescence properties of organic molecules in polymeric media. (1) The efficiency of energy transfer from Coumarine 138 to Rhodamine B in polyacrylic acid (PAA) is measured by both steady state and time dependent methods. The Forster efficiency'' obtained by these two methods is consistent and shows the same pressure dependence as efficiencies derived from relative peak intensities. The non-monotonic pressure dependence of the efficiency is accounted for in terms of the properties of the molecules and the media. (2) The effect of pressure on the luminescent efficiency of molecules with two or more possible excited state geometries has been measured. The efficiency is described in terms of the non-radiative dissipation of energy from a planar excited state and the rates of crossing to and from the possible twisted states as well as non-radiative decay from these states. The processes involved in these two studies are pertinent to a number of technologically and biologically important processes. [copyright]American Institute of Physics

  4. High-pressure study on some superconductors

    CERN Document Server

    Li, K Q; Yao, Y S; Che, G C; Zhao, Z X

    2002-01-01

    High-pressure study has played an important role in the investigation of conventional superconductors. Since the discovery of cuprate superconductors, high-pressure study has become even more important, especially as regards high-pressure synthesis and the effect of pressure. In this report, the new materials Ca-doped Pr-123, (Fe, Cu)-1212, and MgB sub 2 - a very new and interesting system synthesized under high pressure with good quality - will be discussed. Chemical inner pressure has been thought to explain the high T sub c of Ca-doped Pr-123. As another possibility, the replacement of the physical pressure effect by a chemical effect will be discussed.

  5. Study of ceramics sintering under high pressures

    International Nuclear Information System (INIS)

    Kunrath Neto, A.O.

    1990-01-01

    A systematic study was made on high pressure sintering of ceramics in order to obtain materials with controlled microstructure, which are not accessible by conventional methods. Some aspects with particular interest were: to achieve very low porosity, with fine grains; to produce dispersed metastable and denser phases which can act as toughening agents; the study of new possibilities for toughening enhancement. (author)

  6. Raman study of opal at high pressure

    Science.gov (United States)

    Farfan, G.; Wang, S.; Mao, W. L.

    2011-12-01

    More commonly known for their beauty and lore as gemstones, opals are also intriguing geological materials which may have potential for materials science applications. Opal lacks a definite crystalline structure, and is composed of an amorphous packing of hydrated silica (SiO2) spheroids, which provides us with a unique nano-scaled mineraloid with properties unlike those of other amorphous materials like glass. Opals from different localities were studied at high pressure using a diamond anvil cell to apply pressure and Raman spectroscopy to look at changes in bonding as pressure was increased. We first tested different samples from Virgin Valley, NV, Spencer, ID, Juniper Ridge, OR, and Australia, which contain varying amounts of water at ambient conditions, using Raman spectroscopy to determine if they were opal-CT (semicrystalline cristobalite-trydimite volcanic origin) or opal-A (amorphous sedimentary origin). We then used x-ray diffraction and Raman spectroscopy in a diamond anvil cell to see how their bonding and structure changed under compression and to determine what effect water content had on their high pressure behavior. Comparison of our results on opal to other high pressure studies of amorphous materials like glass has implications from a geological and materials science standpoint.

  7. Recent progress in high-pressure studies on organic conductors

    Directory of Open Access Journals (Sweden)

    Syuma Yasuzuka and Keizo Murata

    2009-01-01

    Full Text Available Recent high-pressure studies of organic conductors and superconductors are reviewed. The discovery of the highest Tc superconductivity among organics under high pressure has triggered the further progress of the high-pressure research. Owing to this finding, various organic conductors with the strong electron correlation were investigated under high pressures. This review includes the pressure techniques using the cubic anvil apparatus, as well as high-pressure studies of the organic conductors up to 10 GPa showing extraordinary temperature and pressure dependent transport phenomena.

  8. High-pressure structural study of Ammonium Perchlorate

    Science.gov (United States)

    Stavrou, Elissaios; Zaug, Joseph; Bastea, Sorin; Grivickas, Paulius; Greenberg, Eran; Kunz, Martin

    Ammonium perchlorate (AP) with the chemical formula NH4ClO4 is a powerful energetic oxidizer used as an ingredient in rocket propellants and explosive formulations. For this reason, its structural properties under extreme conditions have attracted considerable attention (M. Dunuwille et al., S. Hunter et al.). However, its structural properties under pressure are not completely understood. In addition to its importance as an energetic oxidizer, AP is one of the simplest supramolecular systems. Thus, a structural study of AP under pressure can provide crucial information in the context of the emerging field of high pressure supramolecular chemistry. Ammonium perchlorate has been studied using x-ray diffraction and Raman spectroscopy up to the record pressure of 40 GPa. The results reveal a pressure-induced first order phase transition at 4 GPa, in agreement with previous studies. However, preliminary analysis of our results contradicts with the previously proposed high-pressure phase, as determined by neutron diffraction. No further structural phase transitions have been observed up to the highest pressure of this study. Intermolecular bonding between NH4 and ClO4 ions will be discussed based on Raman spectroscopy measurements. This work was performed under the auspices of the U. S. Department of Energy by Lawrence Livermore National Security, LLC under Contract DE-AC52-07NA27344.

  9. High pressure study of high-temperature superconductors

    Energy Technology Data Exchange (ETDEWEB)

    Souliou, Sofia-Michaela

    2014-09-29

    -to-orthorhombic transition survives with the application of high pressures up to 85 kbars. In addition, our Raman data reveal a linewidth renormalization of the c-axis polarized A{sub 1g} and B{sub 1g} Raman phonons through the magnetic transition, similar to the one previously observed in the ''122'' family and attributed to the opening of the spin density wave gap. The renormalization is gradually suppressed under high pressure, in line with an earlier high pressure magnetization study which reported the pressure-induced decrease of the magnetic transition temperature. The linewidth anomaly disappears at 8 GPa suggesting the complete suppression of the magnetic transition at this pressure.

  10. High Pressure Studies of UO3

    Science.gov (United States)

    Jenei, Zsolt; Lipp, Magnus; Klepeis, Jae-Hyun; Baer, Bruce; Cynn, Hyunchae; Evans, William; Park, Changyong; Popov, Dimitri

    2011-03-01

    It has been reported that upon compression t ambient temperature δ -UO3 becomes amorphous at 2.2 GPa. (Journal of Alloys and Compounds 315 p59--61). We studied the properties of γ -UO3 in diamond anvil cell up to 75 GPa. Powder diffraction experiments performed at HPCAT/Advanced Photon Source show the crystalline uranium trioxide transforms to an amorphous solid between 12 and 14 GPa and remains amorphous up to 75 GPa. The transition has been confirmed by Raman spectroscopy as well. In this paper we'll present our findings on the amorphous transition together with the equation of state of both the crystalline phase and the amorphous phase. This work performed under the auspices of the US DOE by LLNL under Contract DE-AC52-07NA27344 HPCAT is supported by CIW, CDAC, UNLV and LLNL through funding from DOE-NNSA, DOE-BES and NSF. APS is supported by DOE-BES, under Contract No. DE-AC02-06CH11357.

  11. Proteomics analysis in frozen horse mackerel previously high-pressure processed.

    Science.gov (United States)

    Pazos, Manuel; Méndez, Lucía; Vázquez, Manuel; Aubourg, Santiago P

    2015-10-15

    The effect of high-pressure processing (HPP) (150, 300 and 450 MPa for 0, 2.5 and 5 min) on total sodium dodecyl sulphate (SDS)-soluble and sarcoplasmic proteins in frozen (-10 °C for 3 months) horse mackerel (Trachurus trachurus) was evaluated. Proteomics tools based on image analysis of SDS-PAGE protein gels and protein identification by tandem mass spectrometry (MS/MS) were applied. Although total SDS-soluble fraction indicated no important changes induced by HPP, this processing modified the 1-D SDS-PAGE sarcoplasmic patterns in a direct-dependent manner and exerted a selective effect on particular proteins depending on processing conditions. Thus, application of the highest pressure (450 MPa) provoked a significant degradation of phosphoglycerate mutase 2, glycogen phosphorylase muscle form, pyruvate kinase muscle isozyme, beta-enolase and triosephosphate isomerase and phosphoglucomutase-1. Conversely, protein bands assigned to tropomyosin alpha-1 chain, fast myotomal muscle troponin T and parvalbumin beta 2 increased their intensity after applying a 450-MPa processing. Copyright © 2015 Elsevier Ltd. All rights reserved.

  12. Invitation to neutron scattering study at ultra high pressure

    International Nuclear Information System (INIS)

    Hamaya, Nozomu

    2006-01-01

    Understanding of the pressure evolution of physical and chemical properties of hydrogen is the ultimate goal of the high pressure science. This purpose has simulated the development of low-temperature high-pressure technique for neutron diffraction study. With benefit of high intensity neutron sources a new diamond anvil cell (DAC) has been invented by I.N. Goncharenko. This device allows us to study neutron diffraction under extreme conditions of pressures up to 50 GPa, temperatures down to 0.1 K and applied magnetic fields up to 7.5 T. We describe the details of this technique in the hope that J-PARC (Japan Proton Accelerator Research Complex) will make an epoch in ultra-high-pressure research. (author)

  13. Structural changes in tetracyanoethylene at high pressures: neutron diffraction study

    International Nuclear Information System (INIS)

    Mukhopadhyay, R.; Chaplot, S.L.

    2002-01-01

    We report on structural changes in monoclinic tetracyanoethylene, C 2 (CN) 4 as studied by in situ high-pressure (0-5 GPa) neutron powder diffraction experiments. Structural parameters were obtained by Rietveld profile refinement of the diffraction pattern up to P=2.5 GPa. Above this pressure the width parameter is found to diverge, indicating pressure-induced disordering at 2.5 GPa. The recovered sample, on release of pressure from 5 GPa, is found to have transformed to a graphite-like amorphous structure. The transformation to a graphite-like material has been verified by an independent high-pressure x-ray diffraction experiment. (author)

  14. Feasibility studies for high pressure neutron powder diffraction experiments

    International Nuclear Information System (INIS)

    Von Dreele, R.B.; Parise, J.

    1990-01-01

    We recently performed two neutron powder diffraction experiments on very small samples on the High Intensity Powder Diffractometer (HIPD). These were done to determine the feasibility of performing in situ high pressure/high temperature neutron diffraction experiments on HIPD at pressures which would exceed the previous limit of ∼50 kbar achievable in a neutron diffraction experiment. The first experiment consisted of examining the product from a high pressure preparation done at Stony Brook. The sample, which had been prepared at 65 kbar and 1000 degree C, consisted of a small platinum capsule filled with CaGeO 3 perovskite. The weights of the capsule included 225 mg of platinum and 49 mg of the germanate. A diffraction experiment taking ∼8.6 hrs at a LANSCE proton beam current of ∼53 μA gave peaks of good intensity from both Pt and CaGeO 3 ; we could begin to see them after only 20 min of beam time. The second experiment was to test the possibility of diffraction from a high pressure apparatus. We placed in the HIPD sample position the central assembly from a 100 kbar octahedral press. Four tungsten carbide anvils and a copper block previously pressed to 65 kbar were held in an aluminum frame. The sample consisted of a small bit of nickel foil (175 mg) placed in a 3 mm hole in the copper block. The active sample volume is defined by the gap between the anvils and the length of the sample. A small portion of the copper block is also seen in this arrangement. This is viewed at 90 degree 2Θ through a similar gap between the anvils by 4 1/2 in. x 12 in. 3 He counter tubes. This arrangement simulates the operating conditions of a high pressure run at 100 kbar and takes advantage of the fixed instrument geometry possible in time-of-flight neutron diffraction experiments

  15. Aging study of boiling water reactor high pressure injection systems

    International Nuclear Information System (INIS)

    Conley, D.A.; Edson, J.L.; Fineman, C.F.

    1995-03-01

    The purpose of high pressure injection systems is to maintain an adequate coolant level in reactor pressure vessels, so that the fuel cladding temperature does not exceed 1,200 degrees C (2,200 degrees F), and to permit plant shutdown during a variety of design basis loss-of-coolant accidents. This report presents the results of a study on aging performed for high pressure injection systems of boiling water reactor plants in the United States. The purpose of the study was to identify and evaluate the effects of aging and the effectiveness of testing and maintenance in detecting and mitigating aging degradation. Guidelines from the United States Nuclear Regulatory Commission's Nuclear Plant Aging Research Program were used in performing the aging study. Review and analysis of the failures reported in databases such as Nuclear Power Experience, Licensee Event Reports, and the Nuclear Plant Reliability Data System, along with plant-specific maintenance records databases, are included in this report to provide the information required to identify aging stressors, failure modes, and failure causes. Several probabilistic risk assessments were reviewed to identify risk-significant components in high pressure injection systems. Testing, maintenance, specific safety issues, and codes and standards are also discussed

  16. Feasibility studies for high pressure neutron powder diffraction experiments

    International Nuclear Information System (INIS)

    Von Dreele, R.B.

    1991-01-01

    We recently performed two neutron powder diffraction experiments on very small samples on the High Intensity Powder Diffractometer (HIPD), to determine the feasibility of performing in situ high pressure/high temperature neutron diffraction experiments on HIPD at pressures which would exceed the previous limit of ∼50kbar achievable in a neutron diffraction experiment. The sample, which had been prepared at 65kbar and 1000degC, consisted of a small platinum capsule filled with CaGeO 3 perovskite. A diffraction experiment taking ∼8.6hrs at a LANSCE proton beam current of ∼53μA gave peaks of good intensity from both Pt and CaGeO 3 ; we could begin to see them after only 20min if beam time. The second experiment was to test the possibility of diffraction from a high pressure apparatus. We placed in the HIPD sample position the central assembly from a 100kbar octahedral press. Four tungsten carbide anvils and a copper block previously pressed to 65kbar were held in an aluminum frame. The sample consisted of a small bit of nickel foil placed in a 3 mm hole in the copper block. The active sample volume is defined by the gap (∼0.7mm) between the anvils and the length of the sample. A small portion of the copper block is also seen in this arrangement. This is viewed at 90deg 2Θ through a similar gap between the anvils by 4 1/2''x12'' 3 He counter tubes. This arrangement simulates the operating conditions of a high pressure run at 100kbar and takes advantage of the fixed instrument geometry possible in time-of-flight neutron diffraction experiments. We obtained a diffraction pattern in ∼7.1hrs and ∼57μA beam current which clearly showed peaks from both copper and nickel with no evidence of diffraction from the anvils or any other part of the assembly. These two experiments clearly demonstrate the feasibility of performing high pressure in situ diffraction experiments in excess of 100kbar on HIPD at LANSCE. (J.P.N.)

  17. High Pressure X-Ray Diffraction Studies of Nanocrystalline Materials

    Science.gov (United States)

    Palosz, B.; Stel'makh, S.; Grzanka, E.; Gierlotka, S.; Palosz, W.

    2004-01-01

    Experimental evidence obtained for a variety of nanocrystalline materials suggest that the crystallographic structure of a very small size particle deviates from that in the bulk crystals. In this paper we show the effect of the surface of nanocrystals on their structure by the analysis of generation and distribution of macro- and micro-strains at high pressures and their dependence on the grain size in nanocrystalline powders of Sic. We studied the structure of Sic nanocrystals by in-situ high-pressure powder diffraction technique using synchrotron and neutron sources and hydrostatic or isostatic pressure conditions. The diffraction measurements were done in HASYLAB at DESY using a Diamond Anvil Cell (DAC) in the energy dispersive geometry in the diffraction vector range up to 3.5 - 4/A and under pressures up to 50 GPa at room temperature. In-situ high pressure neutron diffraction measurements were done at LANSCE in Los Alamos National Laboratory using the HIPD and HIPPO diffractometers with the Paris-Edinburgh and TAP-98 cells, respectively, in the diffraction vector range up to 26 Examination of the response of the material to external stresses requires nonstandard methodology of the materials characterization and description. Although every diffraction pattern contains a complete information on macro- and micro-strains, a high pressure experiment can reveal only those factors which contribute to the characteristic diffraction patterns of the crystalline phases present in the sample. The elastic properties of powders with the grain size from several nm to micrometers were examined using three methodologies: (l), the analysis of positions and widths of individual Bragg reflections (used for calculating macro- and micro-strains generated during densification) [I], (2). the analysis of the dependence of the experimental apparent lattice parameter, alp, on the diffraction vector Q [2], and (3), the atomic Pair Distribution Function (PDF) technique [3]. The results

  18. NATO Advanced Study Institute on High-Pressure Crystallography

    CERN Document Server

    Boldyreva, Elena; High-Pressure Crystallography

    2010-01-01

    This book is devoted to the theme of crystallographic studies at high pressure, with emphasis on the phenomena characteristic to the compressed state of matter, as well as experimental and theoretical techniques used to study these phenomena. As a thermodynamic parameter, pressure is remarkable in many ways. In the visible universe its value spans over sixty orders of magnitude, from the non-equilibrium pressure of hydrogen in intergalactic space, to the kind of pressure encountered within neutron stars. In the laboratory, it provides the unique possibility to control the structure and properties of materials, to dramatically alter electronic properties, and to break existing, or form new chemical bonds. This agenda naturally encompasses elements of physics (properties, structure and transformations), chemistry (reactions, transport), materials science (new materials) and engineering (mechanical properties); in addition it has direct applications and implications for geology (minerals in deep Earth environmen...

  19. NMR studies of liquids and disordered solids at high pressure. [Pulsed and high-pressure techniques

    Energy Technology Data Exchange (ETDEWEB)

    Fury, Michael Andrew [Univ. of Illinois, Urbana-Champaign, IL (United States)

    1978-01-01

    Molecular reorientation and translation in molecular liquids was studied. A dominant premise in these studies was that, except in strongly hydrogen-bonded systems such as water, the dynamics of a liquid may be considered to be a series of impulsive collisions. Details of the behavior would be dominated by the shape and size of the molecules under constant packing conditions. The second area of effort was in the plastic crystalline solid phase of two globular molecules, adamantane and cyclohexane. The NMR technique was used in these studies to measure self-diffusion coefficients and spin-lattice relaxation times. The applicability of pulsed NMR techniques to the study of the kinetics of order--disorder phase transitions in solid adamantane was demonstrated.

  20. A study on the relief of shell wall thinning of high pressure feedwater heater

    International Nuclear Information System (INIS)

    Kim, Hyung Joon; Park, Sang Hoon; Seo, Hyuk Ki; Kim, Kyung Hoon; Hwang, Kyung Mo

    2008-01-01

    Feedwater heaters of many nuclear power plants have recently experienced severe wall thinning damage, which will increase as operating time progresses. Several nuclear power plants in Korea have experienced wall thinning damage in the area around the impingement baffle-installed downstream of the high pressure turbine extraction stream line- inside number 5A and 5B feedwater heaters. At that point, the extracted steam from the high pressure turbine is two phase fluid at high temperature, high pressure, and high speed. Since it flows in reverse direction after impinging the impingement baffle, the shell wall of the number 5 high pressure feedwater heater may be affected by flow-accelerated corrosion. This paper describes operation of experience and numerical analysis composed similar condition with real high pressure feedwater heater. This study applied squared, curved and new type impingement baffle plates to feedwater heater same as previous study. In addition, it shows difference of pressure distribution and value between single phase and two phase based on experience and numerical analysis

  1. Thermal neutron scattering studies of condensed matter under high pressures

    International Nuclear Information System (INIS)

    Carlile, C.J.; Salter, D.C.

    1978-01-01

    Although temperature has been used as a thermodynamic variable for samples in thermal neutron scattering experiments since the inception of the neutron technique, it is only in the last decade that high pressures have been utilised for this purpose. In the paper the problems particular to this field of work are outlined and a review is made of the types of high-pressure cells used and the scientific results obtained from the experiments. 103 references. (author)

  2. High pressure calorimetric studies of gas-polymer interactions

    Science.gov (United States)

    Banerjee, Tapan

    Gas sorption in polymeric materials is marked by mass uptake, volume dilation and enthalpy release. The enthalpy of sorption is a measure of polymer-penetrant interactions that complements mass uptake and volume dilation. We have developed a novel technique for direct measurement of enthalpy release, diffusion coefficient of gases and glass transition temperature of polymers in the presence of gas by high pressure microcalorimeter. Polymers used in this study are: bisphenol-A polycarbonate (PC), tetramethyl polycarbonate, tetrachloro polycarbonate, tetrabromo polycarbonate, poly(methyl methacrylate) and poly-dimethyl siloxane (PDMS). Gas used in the study is COsb2. Sorption is an exothermic phenomena. The heat of sorption in PDMS is constant at -1.5 kcal/mole, up to 300 psig and does not change upon depressurization. In PC, the heat of sorption changes from -3.4 kcal/mole during pressurization to -7.2 kcal/mole during depressurization due to presence of excess free volume regions in the glassy polycarbonate. The magnitude of enthalpy of sorption increases with conditioning pressure. Enthalpy of carbon dioxide sorption in polycarbonate substitutes are measured All samples were preconditioned with COsb2 at 300 psig and 35sp°C for 24 hours. The magnitude of the heat of sorption does not correlate well with polymer free volume, gas solubility or gas partial molar volume. The results suggest that free volume regions are not uniformly accessible. The transient signal from enthalpy of sorption experiment is used to extract diffusion coefficient. The diffusivities appear to be independent of sorbed gas concentration due to thermal inertia of the instrument although a increasing trend is expected. Glass transition temperature of polymers in the presence of high pressure COsb2 is measured. Tsbg measurements of the COsb2 - Poly(methyl methacrylate) system as a function g of gas phase pressure were made. Foaming appears to interfere with Tsbg measurement at the highest gas

  3. Structural studies at high pressure using time-of-flight neutron powder diffraction

    International Nuclear Information System (INIS)

    Jorgensen, J.D.

    1989-07-01

    Time-of-flight neutron powder diffraction offers unique capabilities for structural studies at high pressure. Scientific applications have included studies of compression mechanisms, new high-pressure structures, and phase transitions. 11 refs., 1 fig

  4. Experimental studies on radiation effects under high pressure oxygen

    International Nuclear Information System (INIS)

    Fujimura, Eisuke

    1974-01-01

    The effect of oxygen tension on the radiosensitivity of tumor cells is well known, but its clinical application for radiotherapy is not yet established. Rabbits with V x 2 carcinoma in the maxilla were irradiated by 60 Co under high pressure oxygen (experimental group), and compared with those treated in air (control group). For the purpose of examining the clinical effects of high pressure oxygen, an experiment was made in vivo. The following items were compared respectively: a) Tumor regression effect b) Tumor clearance rate c) Survival days d) Half size reduction time e) Inhibition of DNA synthesis in the tumor tissue. Results obtained were as follows: a) 56 per cent of animals showed tumor regression in the experimental group, whereas it occured 26 per cent in the control group. b) 53 per cent of animals showed tumor disappearance in the experimental group, while it was observed only in 13 per cent in the control group. c) Only 2 of 30 rabbits irradiated in air survived over 180 days, whereas 11 of 30 rabbits survived meanwhile in the group irradiated under high pressure oxygen. d) About 11 days were necessary to reduce the tumor size by half after irradiation in the group under high pressure oxygen, while it took 17 days in the group treated in normal air. e) DNA synthesis was inhibited more prominently in the group irradiated under high pressure oxygen in normal air. (author)

  5. X-ray Diffraction Study of Arsenopyrite at High Pressure

    Energy Technology Data Exchange (ETDEWEB)

    D Fan; M Ma; W Zhou; S Wei; Z Chen; H Xie

    2011-12-31

    The high-pressure X-ray diffraction study of a natural arsenopyrite was investigated up to 28.2 GPa using in situ angle-dispersive X-ray diffraction and a diamond anvil cell at National Synchrotron Light Source, Brookhaven National Laboratory. The 16:3:1 methanol-ethanol-water mixture was used as a pressure-transmitting medium. Pressures were measured using the ruby-fluorescence method. No phase change has been observed up to 28.2 GPa. The isothermal equation of state (EOS) was determined. The values of K{sub 0}, and K'{sub 0} refined with a third-order Birch-Murnaghan EOS are K{sub 0} = 123(9) GPa, and K'{sub 0} = 5.2(8). Furthermore, we confirm that the linear compressibilities ({beta}) along a, b and c directions of arsenopyrite is elastically isotropic ({beta}{sub a} = 6.82 x 10{sup -4}, {beta}{sub b} = 6.17 x 10{sup -4} and {beta}{sub c} = 6.57 x 10{sup -4} GPa{sup -1}).

  6. High Pressure X-Ray Diffraction Studies on Nanocrystalline Materials

    Science.gov (United States)

    Palosz, B.; Stelmakh, S.; Grzanka, E.; Gierlotka, S.; Pielaszek, R.; Bismayer, U.; Werner, S.; Palosz, W.

    2003-01-01

    Application of in situ high pressure powder diffraction technique for examination of specific structural properties of nanocrystals based on the experimental data of SiC nanocrystalline powders of 2 to 30 nrn diameter in diameter is presented. Limitations and capabilities of the experimental techniques themselves and methods of diffraction data elaboration applied to nanocrystals with very small dimensions (nanoparticles of different grain size.

  7. Growth and high pressure studies of zirconium sulphoselenide ...

    Indian Academy of Sciences (India)

    tance was monitored in a Bridgman opposed anvil set-up up to 8 GPa pressure to identify the occurrence of any structural transition. These crystals do not possess any structural transitions upto the pressure limit examined. Keywords. Single crystals; chemical vapour transport (CVT) technique; high pressure;. Bridgman anvil ...

  8. High-Pressure Microscopy for Studying Molecular Motors.

    Science.gov (United States)

    Nishiyama, Masayoshi

    2015-01-01

    Movement is a fundamental characteristic of all living things. This biogenic function is carried out by various nanometer-sized molecular machines. Molecular motor is a typical molecular machinery in which the characteristic features of proteins are integrated; these include enzymatic activity, energy conversion, molecular recognition and self-assembly. These biologically important reactions occur with the association of water molecules that surround the motors. Applied pressures can alter the intermolecular interactions between the motors and water. In this chapter we describe the development of a high-pressure microscope and a new motility assay that enables the visualization of the motility of molecular motors under conditions of high-pressure. Our results demonstrate that applied pressure dynamically changes the motility of molecular motors such as kinesin, F1-ATPase and bacterial flagellar motors.

  9. High pressure apparatus transport properties study in high magnetic field

    Czech Academy of Sciences Publication Activity Database

    Honda, F.; Sechovský, V.; Mikulina, O.; Kamarád, Jiří; Alsmadi, A. M.; Nakotte, H.; Lacerda, A. H.

    2002-01-01

    Roč. 16, 20, 21 & 22 (2002), s. 3330-3333 ISSN 0217-9792 R&D Projects: GA ČR GP202/01/D045; GA ČR GA202/00/1217; GA MŠk ME 165 Grant - others:NSF(XX) DMR-0094241 Institutional research plan: CEZ:AV0Z1010914 Keywords : high-pressure apparatus Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.604, year: 2002

  10. High-pressure neutron diffraction studies at LANSCE

    International Nuclear Information System (INIS)

    Zhao, Yusheng; Zhang, Jianzhong; Xu, Hongwu; Lokshin, Konstantin A.; He, Duanwei; Qian, Jiang; Pantea, Cristian; Daemen, Luke L.; Vogel, Sven C.; Ding, Yang; Xu, Jian

    2010-01-01

    The development of neutron diffraction under extreme pressure (P) and temperature (T) conditions is highly valuable to condensed matter physics, crystal chemistry, materials science, and earth and planetary sciences. We have incorporated a 500-ton press TAP-98 into the HiPPO diffractometer at the Los Alamos Neutron Science Center (LANSCE) to conduct in situ high-P-T neutron diffraction experiments. We have developed a large gem-crystal anvil cell, ZAP, to conduct neutron diffraction experiments at high P. The ZAP cell can be used to integrate multiple experimental techniques such as neutron diffraction, laser spectroscopy, and ultrasonic interferometry. More recently, we have developed high-P low-T gas/liquid cells in conjunction with neutron diffraction. These techniques enable in situ and real-time examination of gas uptake/release processes and allow accurate, time-dependent determination of changes in crystal structure and related reaction kinetics. We have successfully used these techniques to study the equations of state, structural phase transitions, and thermo-mechanical properties of metals, ceramics, and minerals. We have conducted researches on the formation/decomposition kinetics of methane, CO 2 and hydrogen hydrate clathrates, and hydrogen/CO 2 adsorption of inclusion compounds such as metal-organic frameworks (MOFs). The aim of our research is to accurately map out phase relations and determine structural parameters (lattice constants, atomic positions, atomic thermal parameters, bond lengths, bond angles, etc.) in the P-T-X space. We are developing further high-P-T technology with a new 2000-ton press, TAPLUS-2000, and a ZIA (Deformation-DIA type) cubic anvil package to routinely achieve pressures up to 20 GPa and temperatures up to 2000 K. The design of a dedicated high-P neutron beamline, LAPTRON, is also underway for simultaneous high-P-T neutron diffraction, ultrasonic, calorimetry, radiography, and tomography studies. Studies based on high-pressure

  11. High pressure dielectric studies on the structural and orientational glass.

    Science.gov (United States)

    Kaminska, E; Tarnacka, M; Jurkiewicz, K; Kaminski, K; Paluch, M

    2016-02-07

    High pressure dielectric studies on the H-bonded liquid D-glucose and Orientationally Disordered Crystal (ODIC) 1,6-anhydro-D-glucose (levoglucosan) were carried out. It was shown that in both compounds, the structural relaxation is weakly sensitive to compression. It is well reflected in the low pressure coefficient of the glass transition and orientational glass transition temperatures which is equal to 60 K/GPa for both D-glucose and 1,6-anhydro-D-glucose. Although it should be noted that ∂Tg(0)/∂p evaluated for the latter compound seems to be enormously high with respect to other systems forming ODIC phase. We also found that the shape of the α-loss peak stays constant for the given relaxation time independently on the thermodynamic condition. Consequently, the Time Temperature Pressure (TTP) rule is satisfied. This experimental finding seems to be quite intriguing since the TTP rule was shown to work well in the van der Waals liquids, while in the strongly associating compounds, it is very often violated. We have also demonstrated that the sensitivity of the structural relaxation process to the temperature change measured by the steepness index (mp) drops with pressure. Interestingly, this change is much more significant in the case of D-glucose with respect to levoglucosan, where the fragility changes only slightly with compression. Finally, kinetics of ODIC-crystal phase transition was studied at high compression. It is worth mentioning that in the recent paper, Tombari and Johari [J. Chem. Phys. 142, 104501 (2015)] have shown that ODIC phase in 1,6-anhydro-D-glucose is stable in the wide range of temperatures and there is no tendency to form more ordered phase at ambient pressure. On the other hand, our isochronal measurements performed at varying thermodynamic conditions indicated unquestionably that the application of pressure favors solid (ODIC)-solid (crystal) transition in 1,6-anhydro-D-glucose. This result mimics the impact of pressure on the

  12. System Study: High-Pressure Safety Injection 1998–2013

    Energy Technology Data Exchange (ETDEWEB)

    Schroeder, John Alton [Idaho National Lab. (INL), Idaho Falls, ID (United States). Risk Assessment and Management Services Dept.

    2015-02-01

    This report presents an unreliability evaluation of the high-pressure safety injection system (HPSI) at 69 U.S. commercial nuclear power plants. Demand, run hours, and failure data from fiscal year 1998 through 2013 for selected components were obtained from the Institute of Nuclear Power Operations (INPO) Consolidated Events Database (ICES). The unreliability results are trended for the most recent 10-year period while yearly estimates for system unreliability are provided for the entire active period. No statistically significant increasing or decreasing trends were identified in the HPSI results.

  13. System Study: High-Pressure Core Spray 1998–2013

    Energy Technology Data Exchange (ETDEWEB)

    Schroeder, John Alton [Idaho National Lab. (INL), Idaho Falls, ID (United States). Risk Assessment and Management Services Dept.

    2015-01-31

    This report presents an unreliability evaluation of the high-pressure core spray (HPCS) at eight U.S. commercial boiling water reactors. Demand, run hours, and failure data from fiscal year 1998 through 2013 for selected components were obtained from the Institute of Nuclear Power Operations (INPO) Consolidated Events Database (ICES). The unreliability results are trended for the most recent 10-year period, while yearly estimates for system unreliability are provided for the entire active period. No statistically significant increasing or decreasing trends were identified in the HPCS results.

  14. System Study: High-Pressure Core Spray 1998–2012

    Energy Technology Data Exchange (ETDEWEB)

    T. E. Wierman

    2013-10-01

    This report presents an unreliability evaluation of the high-pressure core spray (HPCS) at 8 U.S. commercial boiling water reactors. Demand, run hours, and failure data from fiscal year 1998 through 2012 for selected components were obtained from the Equipment Performance and Information Exchange (EPIX). The unreliability results are trended for the most recent 10 year period while yearly estimates for system unreliability are provided for the entire active period. No statistically significant increasing or decreasing trends were identified in the HPCS results.

  15. System Study: High-Pressure Core Spray 1998-2014

    Energy Technology Data Exchange (ETDEWEB)

    Schroeder, John Alton [Idaho National Lab. (INL), Idaho Falls, ID (United States). Risk Assessment and Management Services Dept.

    2015-12-01

    This report presents an unreliability evaluation of the high-pressure core spray (HPCS) at eight U.S. commercial boiling water reactors. Demand, run hours, and failure data from fiscal year 1998 through 2014 for selected components were obtained from the Institute of Nuclear Power Operations (INPO) Consolidated Events Database (ICES). The unreliability results are trended for the most recent 10 year period, while yearly estimates for system unreliability are provided for the entire active period. No statistically significant increasing or decreasing trends were identified in the HPCS results.

  16. System Study: High-Pressure Safety Injection 1998–2012

    Energy Technology Data Exchange (ETDEWEB)

    T. E. Wierman

    2013-10-01

    This report presents an unreliability evaluation of the high-pressure safety injection system (HPSI) at 69 U.S. commercial nuclear power plants. Demand, run hours, and failure data from fiscal year 1998 through 2012 for selected components were obtained from the Equipment Performance and Information Exchange (EPIX). The unreliability results are trended for the most recent 10 year period while yearly estimates for system unreliability are provided for the entire active period. No statistically significant increasing or decreasing trends were identified in the HPSI results.

  17. System Study: High-Pressure Safety Injection 1998-2014

    Energy Technology Data Exchange (ETDEWEB)

    Schroeder, John Alton [Idaho National Lab. (INL), Idaho Falls, ID (United States). Risk Assessment and Management Services Dept.

    2015-12-01

    This report presents an unreliability evaluation of the high-pressure safety injection system (HPSI) at 69 U.S. commercial nuclear power plants. Demand, run hours, and failure data from fiscal year 1998 through 2014 for selected components were obtained from the Institute of Nuclear Power Operations (INPO) Consolidated Events Database (ICES). The unreliability results are trended for the most recent 10 year period, while yearly estimates for system unreliability are provided for the entire active period. No statistically significant increasing or decreasing trends were identified in the HPSI results.

  18. High-pressure Brillouin study on methane hydrate

    CERN Document Server

    Sasaki, S; Suwa, I; Kume, T; Shimizu, H

    2002-01-01

    Acoustic velocities and adiabatic elastic constants of structure I of methane hydrate (MH) have been determined as a function of pressure up to 0.6 GPa at 23 deg. C by the high-pressure Brillouin spectroscopy developed for a single molecular crystal. The pressure dependence of the acoustic velocities of MH is very similar to that of ice-Ih except for the longitudinal acoustic (LA) velocity. The value of the LA velocity along the (100) direction of MH at 0.02 GPa is 3.63 km s sup - sup 1 which is about 7% lower than the average of the LA velocities in the ice-Ih phase at -35.5 deg. C and atmospheric pressure.

  19. High pressure Raman study of BaMoO4

    International Nuclear Information System (INIS)

    Christofilos, D.; Kourouklis, G.A.; Arvanitidis, J.; Kampasakali, E.; Papagelis, K.; Ves, S.

    2004-01-01

    The structural stability of polycrystalline BaMoO 4 under hydrostatic pressure has been investigated by means of Raman spectroscopy up to 8 GPa. Raman spectra reveal a pressure induced phase transition at ∝5.8 GPa. Upon pressure release the structure reverts to its ambient pressure scheelite (CaWO 4 ) structure with no observable hysteresis. The large number of Raman active modes of the high pressure phase suggests either an increase of the size of the unit cell and/or a non-centrosymmetric structure leading to the activation of the ungerade modes of the scheelite structure. (copyright 2004 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  20. [Genesis study of omphacite at high pressure and high temperature].

    Science.gov (United States)

    Xiao, Ben-Fu; Yi, Li; Wang, Duo-Jun; Xie, Chao; Tang, Xue-Wu; Liu, Lei; Cui, Yue-Ju

    2013-11-01

    The melting and recrystallizing experiments of alkali basalt powder and mixture of pure oxides mixed as stoichiometry were performed at 3 GPa and 1 200 degrees C. Electronic microprobe analysis and Raman spectra showed that the recrystallized products were omphacites, the FWHM (full width at half maximum) of the Raman peak was narrow and its shape was sharp, which is attributed to the stable Si-O tetrahedral structure and the high degree of order in omphacite. Based on the results of previous studies, the influencing factors of omphacite genesis and its primary magma were discussed. The results showed that the formation of omphacite could be affected by many factors, such as the composition of parent rocks, the concentration of fluid in the system and the conditions of pressure and temperature. This result could support some experimental evidences on the genesis studies of omphacite and eclogite.

  1. High-pressure Moessbauer study of perovskite iron oxides

    CERN Document Server

    Kawakami, T; Sasaki, T; Kuzushita, K; Morimoto, S; Endo, S; Kawasaki, S; Takano, M

    2002-01-01

    The perovskite oxides CaFeO sub 3 and La sub 1 sub / sub 3 Sr sub 2 sub / sub 3 FeO sub 3 have been investigated by high-pressure sup 5 sup 7 Fe Moessbauer spectroscopy. The critical temperatures of the charge disproportionation (CD) and the magnetic order (MO) have been determined as a function of pressure. In CaFeO sub 3 the CD (2Fe sup 4 sup + -> Fe sup 3 sup + + Fe sup 5 sup +) occurs at an almost constant temperature of 290 K in the pressure range of 0-17 GPa. Above 20 GPa, the CD is suppressed. The MO temperature of 125 K at an ambient pressure rises to 300 K at 34 GPa. In La sub 1 sub / sub 3 Sr sub 2 sub / sub 3 FeO sub 3 the CD (3Fe sup 1 sup 1 sup / sup 3 sup + -> 2Fe sup 3 sup + + Fe sup 5 sup +) and the MO occur at the same temperature up to 21 GPa, which decreases from 207 to 165 K with increasing pressure. Above 25 GPa, however, the MO temperature rises above 400 K.

  2. High Pressure X-ray Diffraction Studies on Barium.

    Science.gov (United States)

    Barnett, J D; Bennion, R B; Hall, H T

    1963-08-09

    Simultaneous x-ray diffraction and electrical resistance measurements on barium establish, with certainty, that Bridgman's 78-kb resistance transition is identical with his 59-kb volumetransition. During this transition, the bodycentered cubic structure changes to hexagonalclose packed. Lattice parameters for the latter structure at 62 kb (volume scale) are: a = 3.90 A, c = 6.15 A, and c/a = 1.58. Compression (AV/Vo) at 62 kb is 0.359 + 0.005 compared to 0.345 previously reported by Bridgman. Below the transition, at 49 kb, compression is 0.300 +/- 0.005 compared to Bridgman's 0.288. Bridgman's 17-kb volume transition was not detected by x-ray diffraction.

  3. High-pressure gas chamber for neutron diffraction studies

    International Nuclear Information System (INIS)

    Stepanov, G. N.; Telepnev, A. S.; Simkin, V. G.

    2007-01-01

    The construction of a chamber designed for neutron diffraction studies of the structure of solids under high gas pressures up to 0.5 GPa is described. This chamber is a modification of the chamber published earlier

  4. Pulsed laser kinetic studies of liquids under high pressure

    Energy Technology Data Exchange (ETDEWEB)

    Eyring, E.M.

    1992-09-22

    A laser flash photolysis kinetic study of 2,2{prime}-bipyridine bidentate chelating ligands with one claw in the first coordination sphere of a molybdenum carbonyl complex has been completed at pressures up to 150 MPa. The reaction mechanism for thermal ring closure is found from activation volumes to change from associative interchange to dissociative interchange as substituents on the 2,2{prime}-bipyridine ligands become bulkier. In a similar study of more rigid, substituted phenanthroline bidentate ligands it was found that substituent bulkiness had little effect on the thermal ring closure mechanism. Stability constants for lithium ion complexes with crown ethers in a room temperature molten salt, fluorescence quantum yields for cresyl violet and several other dyes in solution, and the oxidation of alcohols by OsO{sub 4} have also been investigated.

  5. High pressure structural studies of AgInTe2

    International Nuclear Information System (INIS)

    Bovornratanaraks, T; Yoodee, K; Kotmool, K; McMahon, M I; Ruffolo, D

    2010-01-01

    The structural phase transformations in the chalcopyrite semiconductor AgInTe 2 have been studied up to 10 GPa on both pressure increase and decrease. The experiments were conducted using angle-dispersive X-ray diffraction with synchrotron radiation and an image plate. The diffraction patterns of AgInTe 2 at ambient pressure reveal two coexisting phases: the first has the chalcopyrite structure while the second has a zincblende-like structure. On pressure increase both phases transformed at 3-4 GPa to a cation-disordered orthorhombic structure with spacegroup Cmcm. On pressure decrease, the chalcopyrite phase started to reappear at 0.55 GPa, and the Cmcm phase disappeared completely at ambient pressure.

  6. Modeling Study of High Pressure and High Temperature Reservoir Fluids

    DEFF Research Database (Denmark)

    Varzandeh, Farhad

    S-characterization combinations and 260 reservoir fluids. PC-SAFT with the new general characterization method is shown to give the lowest AAD% and maximum deviation in calculation of saturation pressure, density and STO density, among all the tested characterization methods for PC-SAFT. Application of the new characterization...... be highly rewarding if successfully produced. This PhD project is part of the NextOil (New Extreme Oil and Gas in the Danish North Sea) project which is intended to reduce the uncertainties in HPHT field development. The main focus of this PhD is on accurate description of the reservoir fluid behavior under...... HPHT conditions to minimize the production risks from these types of reservoirs. In particular, the study has thoroughly evaluated several non-cubic Equations of State (EoSs) which are considered promising for HPHT fluid modeling, showing their advantages and short comings based on an extensive...

  7. The powerful high pressure tool for protein conformational studies

    Directory of Open Access Journals (Sweden)

    S. Marchal

    2005-08-01

    Full Text Available The pressure behavior of proteins may be summarized as a the pressure-induced disordering of their structures. This thermodynamic parameter has effects on proteins that are similar but not identical to those induced by temperature, the other thermodynamic parameter. Of particular importance are the intermolecular interactions that follow partial protein unfolding and that give rise to the formation of fibrils. Because some proteins do not form fibrils under pressure, these observations can be related to the shape of the stability diagram. Weak interactions which are differently affected by hydrostatic pressure or temperature play a determinant role in protein stability. Pressure acts on the 2º, 3º and 4º structures of proteins which are maintained by electrostatic and hydrophobic interactions and by hydrogen bonds. We present some typical examples of how pressure affects the tertiary structure of proteins (the case of prion proteins, induces unfolding (ataxin, is a convenient tool to study enzyme dissociation (enolase, and provides arguments to understand the role of the partial volume of an enzyme (butyrylcholinesterase. This approach may have important implications for the understanding of the basic mechanism of protein diseases and for the development of preventive and therapeutic measures.

  8. Thermal versus high pressure processing of carrots: A comparative pilot-scale study on equivalent basis

    NARCIS (Netherlands)

    Vervoort, L.; Plancken, Van der L.; Grauwet, T.; Verlinde, P.; Matser, A.M.; Hendrickx, M.; Loey, van A.

    2012-01-01

    This report describes the first study comparing different high pressure (HP) and thermal treatments at intensities ranging from mild pasteurization to sterilization conditions. To allow a fair comparison, the processing conditions were selected based on the principles of equivalence. Moreover,

  9. Ammonium Azide under High Pressure - a combined Theoretical and Experimental Study

    Science.gov (United States)

    Radousky, Harry; Crowhurst, Jonathan; Zaug, Joseph; Steele, Bradley; Landerville, Aaron; Oleynik, Ivan

    2015-03-01

    Efforts to synthesize, characterize and recover novel polynitrogen energetic materials have driven attempts to subject high nitrogen content precursor materials (in particular metal and non-metal azides) to elevated pressures. Here we present a combined theoretical and experimental study of the high pressure behavior of ammonium azide (NH4N3) . Using density functional theory we have considered the relative thermodynamic stability of the material with respect to two other crystal phases, namely trans-tetrazene (TTZ), and also a novel hydronitrogen solid (HNS) of the form (NH)4, that was recently predicted to become relatively stable under high pressure. Experimentally we have measured the Raman spectra of NH4N3 up to 71 GPa at room temperature. Our calculations demonstrate that the HNS becomes stable only at pressures much higher (89.4 GPa) than previously predicted (36 GPa). Our Raman spectra are consistent with earlier reports up to lower pressures, and at higher pressures, while some additional subtle behavior is observed (e.g. mode splitting) there is again no evidence of a phase transition to either TTZ or the HNS. Research performed under the auspices of the U.S. DOE by LLNL under Contract No. DE-AC52-07NA27344 (Work at USF and LLNL supported by DTRA Grant HDTRA1-12-1-0023). LLNL-JRNL-651736.

  10. A new high pressure phase of sodium formate dihydrate; an experimental and computational study.

    Science.gov (United States)

    Walker, Martin; Morrison, Carole A; Allan, David R; Pulham, Colin R; Marshall, William G

    2007-05-28

    As part of an on-going programme to study the high pressure structural behaviour of hydrated small molecular systems, sodium formate dihydrate has been studied using high pressure single crystal X-ray and neutron powder diffraction methods. A new phase was initially identified at 17 kbar by X-ray diffraction and high level quantum mechanical calculations completed the structure, allowing definitive hydrogen atom positioning. The resulting structure compared favourably with that found subsequently by high pressure neutron diffraction. The neutron diffraction study also revealed that the deuterated form, NaDCO(2).2D(2)O, is stable in a different structural form to that of the non-deuterated material at ambient pressure. The structure of this phase is related to that of the high pressure phase via a simple translation of the molecular layers.

  11. High-pressure electron-resonance studies of electronic, magnetic, and structural phase transitions. Progress report

    International Nuclear Information System (INIS)

    Pifer, J.H.; Croft, M.C.

    1983-01-01

    Research is described in development of a high-pressure electron-resonance probe capable of operating down to 1.5 0 K temperatures. The apparatus has been used to measure the EPR of a sample of DPPH at room temperature and zero pressure. EPR has been used to measure valence field instabilities in alloy systems. Studies have been done on metal-insulator transitions at high pressure, and are briefly described

  12. High-pressure oxygen: a non-conventional magnet studied by means of neutron diffraction

    International Nuclear Information System (INIS)

    Goncharenko, I N

    2005-01-01

    While being among the most casually treated elements on our planet, elementary oxygen shows many unusual features at low temperatures and high pressures. At low pressure, oxygen is the only elementary molecular magnet. Under high pressures solid oxygen undergoes several structural transformations and finally becomes a metal and superconductor under the very high pressure of 96 GPa. For the first time, we studied magnetic ordering in solid oxygen under very high pressures by a direct method, namely by means of neutron diffraction. A new type of magnetic order with ferromagnetic stacking of the antiferromagnetic O 2 planes was discovered in δ-O 2 at P = 6.2 GPa. The structural transitions from α-O 2 to β-O 2 and δ-O 2 correlate with the magnetic transitions; therefore in the pressure range P<7 GPa, oxygen should be considered as a unique 'spin-controlled crystal'

  13. Study of high-pressure adsorption from supercritical fluids by the potential theory

    DEFF Research Database (Denmark)

    Monsalvo, Matias Alfonso; Shapiro, Alexander

    2009-01-01

    The multicomponent potential theory of adsorption (MPTA), which has been previously used to study low-pressure adsorption of subcritical fluids, is extended to adsorption equilibria from supercritical fluids up to high pressures. The MPTA describes an adsorbed phase as an inhomogeneous fluid...... with thermodynamic properties that depend on the distance from the solid surface (or position in the porous space). The description involves the two kinds of interactions present in the adsorbed fluid, i.e. the fluid-fluid and fluid-solid interactions. accounted for by means of an equation of state (Eo......S) and interaction potential functions, respectively. This makes it possible to generate the different MPTA models by combination of the relevant EoS/potentials. In the present work, the simplified perturbed-chain statistical associating fluid theory (sPC-SAFT) EoS is used for the thermodynamic description of both...

  14. High-pressure studies on Tc and crystal structure of iron chalcogenide superconductors

    Directory of Open Access Journals (Sweden)

    Hiroki Takahashi, Takahiro Tomita, Hiroyuki Takahashi, Yoshikazu Mizuguchi, Yoshihiko Takano, Satoshi Nakano, Kazuyuki Matsubayashi and Yoshiya Uwatoko

    2012-01-01

    Full Text Available The superconducting transition temperature, Tc, in iron-based solids can be enhanced by applied pressure: Tc increases from 8 to 37 K for the 11-type FeSe when the pressure is raised from 0 to 4 GPa. High-pressure studies can elucidate the mechanism of superconductivity in such novel materials. In this paper, we present a high-pressure study of Fe(Se1−xTex and Fe(Se1−xSx. In the case of Fe(Se1−xTex, the maximum Tc under high pressure did not exceed the Tc of FeSe, which can be attributed to the structural transition to the monoclinic phase. For Fe(Se1−xSx (0 < x < 0.3, Tc exhibited a significant increase with pressure; however, the maximum Tc under high pressure did not exceed the Tc of FeSe. This may be due to the disorder induced by substituting S for Se, which is similar to the pressure effect on Tc for the 1111-type superconductor Ca(Fe1−xCoxAsF. The Tc of Fe(Se1−xSx showed a complex behavior below 1 GPa, first decreasing and then increasing with increasing pressure. From high-pressure x-ray diffraction measurements, the Tc (P curve was correlated with the local structural parameter.

  15. High-pressure Raman study and lattice dynamical calculations for SrWO4

    International Nuclear Information System (INIS)

    Christofilos, D; Papagelis, K; Ves, S; Kourouklis, G A; Raptis, C

    2002-01-01

    A high-pressure Raman study of SrWO 4 reveals a pressure induced phase transition starting at 11.5 GPa. Several Raman lines exhibit a nonlinear behaviour in the pressure range of 11.5-15 GPa, which can be attributed to either stabilization of the high-pressure phase or an intermediate phase. Using a theoretical lattice dynamical calculation, based on an empirical potential model, we have obtained the Raman active mode eigenvectors giving us an insight into the phase transition mechanism. The lowest-frequency mode exhibits a negative pressure slope in the scheelite phase and involves a motion of the WO 4 tetrahedron as a whole according to the theoretical results. The experimental evidence suggests that the structure of the high-pressure phase is closely related to the scheelite structure, being formed by closely lying distorted WO 4 tetrahedra rather than involving an octahedrally coordinated W ion

  16. Raman study of bromine-doped single-walled carbon nanotubes under high pressure

    CERN Document Server

    Liu Bing Bing; Yu Miao; Zou Guang Tian; Carlsten, J; Wagberg, T; Sundqvist, B

    2002-01-01

    Raman results for different single-walled carbon nanotube bundles doped with Br sub 2 were studied both at ambient pressure and under high pressure up to 6 GPa. Our study indicates that bromine resides in the interstitial channel of nanotube bundles as a form of polymer.

  17. Studies on a thermal insulation layer in the high pressure, high temperature gas, (1)

    International Nuclear Information System (INIS)

    Shimomura, Hiroaki

    1978-03-01

    Basic equations of heat transfer in a thermal insulation layers are presented in the high pressure, high temperature gas atmosphere. Natural convective heat transfer in the packed beds is then studied. Further described are experiments plans and principal particulars of experimental apparatus based on the above discussions. (auth.)

  18. High-pressure X-ray diffraction study of bulk- and nanocrystalline GaN

    DEFF Research Database (Denmark)

    Jorgensen, J.E.; Jakobsen, J.M.; Jiang, Jianzhong

    2003-01-01

    Bulk- and nanocrystalline GaN have been studied by high-pressure energy-dispersive X-ray diffraction. Pressure-induced structural phase transitions from the wurtzite to the NaCl phase were observed in both materials. The transition pressure was found to be 40 GPa for the bulk-crystalline GaN, whi...

  19. Study on flow regimes of high-pressure and dense-phase pneumatic conveying

    International Nuclear Information System (INIS)

    Lu Peng; Chen Xiaoping; Liang Cai; Pu Wenhao; Zhou Yun; Xu Pan; Zhao Changsui

    2009-01-01

    High-pressure and dense-phase pneumatic conveying of pulverized coal is a key technology in the field of large-scale entrained bed coal gasification. Flow regime plays an important role in two-phase flow because it affects not only flow behavior and safety operation, but also the reliability of practical processes. Few references and experiences in high-pressure and dense-phase conveying are available, especially for the flow regimes. And because of the high stickiness and electrostatic attraction of pulverized coal to the pipe wall, it is very difficult to make out the flow regimes in the conveying pipe by visualization method. Thus quartz powder was chosen as the conveyed material to study the flow regime. High-speed digital video camera was employed to photograph the flow patterns. Experiments were conducted on a pilot scale experimental setup at the pressure up to 3.6MPa. With the decrease in superficial gas velocity, three distinguishable flow regimes were observed: stratified flow, dune flow and plug flow. The characteristics of pressure traces acquired by high frequency response pressure transmitter and their EMD (Empirical Mode Decomposition) characteristics were correlated strongly with the flow regimes. Combining high-speed photography and pressure signal analysis together can make the recognition of flow patterns in the high-pressure and dense-phase pneumatic conveying system more accurate. The present work will lead to better understanding of the flow regime transition under high-pressure.

  20. DySb under high pressures: A full-potential study

    International Nuclear Information System (INIS)

    Gupta, Dinesh C.; Kulshrestha, Subhra

    2011-01-01

    Research highlights: → Present study is first of its kind as no theoretical study is reported on DySb except experimental information. → High pressures phase transition properties, magnetic-to-non-magnetic transition, elastic moduli and valence band width at ambient and high pressures, band structure, thermo-physical properties, magnetic moments, etc. have been computed by means of LSDA and LSDA + U approach. → LSDA + U approach is more accurate in predicting the proper nature of f-electrons of rare-earths. → The results are in good agreement with experimental data. - Abstract: The magnetic, structural, electronic and mechanical properties of DySb in the stable Fm3-barm and high-pressure Fm3-barm phase have been analyzed using full potential (linear) augmented plane wave method. The local spin-density approximation along with Hubbard-U corrections and spin-orbit coupling has been used for present calculations. The magnetic phase stability shows that DySb is ferromagnetically stable at ambient and high pressures. Under compression, it undergoes first-order structural transition from B1 to B2 phase at 22.2 GPa which shows good agreement with the experimental value of ∼22 GPa. The elastic properties of DySb have also been computed at normal and high pressures. The structural properties viz, equilibrium lattice constant, bulk modulus and its pressure derivative, transition pressure, volume collapse and elastic moduli are in good agreement with the experimental data. The calculation shows DySb to be semi-metallic.

  1. Nitric acid dihydrate at ambient and high pressure: An experimental and computational study

    International Nuclear Information System (INIS)

    Walker, Martin; Pulham, Colin R.; Morrison, Carole A.; Allan, David R.; Marshall, William G.

    2006-01-01

    The high pressure structural behavior of nitric acid dihydrate ([H 3 O] + ·[NO 3 ] - ·H 2 O) has been investigated up to 3.8 GPa using single crystal x-ray diffraction and neutron powder diffraction techniques. A new structural phase has been identified above 1.33 GPa and this has been further studied by ab initio quantum mechanical calculations. These have guided the refinement by neutron powder diffraction

  2. Neutron diffraction study of Lu2Fe17 under high pressure

    International Nuclear Information System (INIS)

    Prokhnenko, O.; Ritter, C.; Medvedeva, I.; Arnold, Z.; Kamarad, J.; Kuchin, A.

    2003-01-01

    Neutron diffraction techniques were used to study the evolution of the magnetic states of Lu 2 Fe 17 under hydrostatic pressure up to 5 kbar in the temperature range 2-300 K. The ferromagnetic phase gets suppressed by pressure and an incommensurate antiferromagnetic phase is found to exist down to 2 K under a pressure of 5 kbar. The complex thermal evolution of the magnetic structures of Lu 2 Fe 17 at ambient and high pressures is presented and discussed

  3. Study on the high temperature, high pressure operation technique of fuel test loop

    International Nuclear Information System (INIS)

    Chi, Dae Young; Lee, Chung Young; Sim, Bong Shick; Kim, Jun Yun

    2001-04-01

    The project, 'Feasibility review on the installation of FTL in HANARO' charged by KISTEP has been performed for the technical evaluation of the steady state fuel test loop during 4 months from Dec. 2000 to Mar. 2001. This study describes the high temperature, high pressure technology of the FTL. This report includes the followings : - The construction of FTL - The operation schemes of the steady state - The operation procedures of FTL

  4. Study on the high temperature, high pressure operation technique of fuel test loop

    Energy Technology Data Exchange (ETDEWEB)

    Chi, Dae Young; Lee, Chung Young; Sim, Bong Shick; Kim, Jun Yun

    2001-04-01

    The project, 'Feasibility review on the installation of FTL in HANARO' charged by KISTEP has been performed for the technical evaluation of the steady state fuel test loop during 4 months from Dec. 2000 to Mar. 2001. This study describes the high temperature, high pressure technology of the FTL. This report includes the followings : - The construction of FTL - The operation schemes of the steady state - The operation procedures of FTL.

  5. High-pressure cell for luminescence studies of condensed phases at low temperatures

    International Nuclear Information System (INIS)

    Variano, B.F.; Brenner, H.C.; Daniels, W.B.

    1986-01-01

    A clamped optical cell for high-pressure low-temperature fluorescence and phosphorescence studies is described. A particular innovation is the use of a bifurcated fiber-optic lightguide to enable sample illumination and emission collection with a single optical window. This very simple type of cell is adaptable to a variety of optical setups and is easily assembled and disassembled for sample mounting

  6. High-pressure electrical resistivity studies for Ba1-xCsxFe2Se3

    Science.gov (United States)

    Kawashima, C.; Soeda, H.; Takahashi, H.; Hawai, T.; Nambu, Y.; Sato, T. J.; Hirata, Y.; Ohgushi, K.

    2017-10-01

    High-pressure electrical resistance measurements were performed for iron-based ladder material Ba1-xCsxFe2Se3 (x = 0.25 and 0.65) using a diamond anvil cell (DAC). Recent high-pressure study revealed that iron-based ladder material BaFe2S3 exhibits an insulator-metal transition and superconductivity, and this discovery would provide important insight for understanding the mechanism of iron-based superconductors. Therefore, it is intriguing to investigate the high-pressure properties for the iron-based ladder material Ba1-xCsxFe2Se3 system. The parent compounds BaFe2Se3 and CsFe2Se3 show insulating and magnetic ordering features. For Ba1-xCsxFe2Se3 system, no magnetic ordering is observed for x = 0.25 and minimum charge gap was estimated for x = 0.65. The insulator-metal transitions are observed in both materials.

  7. High-pressure Experimental Studies on Geo-liquids Using Synchrotron Radiation at the Advanced Photon Source

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yanbin [Univ. of Chicago, IL (United States); Shen, Guoyin [Carnegie Inst. of Washington, Argonne, IL (United States). Geophysical Lab.

    2014-12-23

    Here, we review recent progress in studying silicate, carbonate, and metallic liquids of geological and geophysical importance at high pressure and temperature, using the large-volume high-pressure devices at the third-generation synchrotron facility of the Advanced Photon Source, Argonne National Laboratory. These integrated high-pressure facilities now offer a unique combination of experimental techniques that allow researchers to investigate structure, density, elasticity, viscosity, and interfacial tension of geo-liquids under high pressure, in a coordinated and systematic fashion. Moreover, we describe experimental techniques, along with scientific highlights. Future developments are also discussed.

  8. A new phase of ThC at high pressure predicted from a first-principles study

    Science.gov (United States)

    Guo, Yongliang; Qiu, Wujie; Ke, Xuezhi; Huai, Ping; Cheng, Cheng; Han, Han; Ren, Cuilan; Zhu, Zhiyuan

    2015-08-01

    The phase transition of thorium monocarbide (ThC) at high pressure has been studied by means of density functional theory. Through structure search, a new phase with space group P 4 / nmm has been predicted. The calculated phonons demonstrate that this new phase and the previous B2 phase are dynamically stable as the external pressure is greater than 60 GPa and 120 GPa, respectively. The transformation from B1 to P 4 / nmm is predicted to be a first-order transition, while that from P 4 / nmm to B2 is found to be a second-order transition.

  9. 1H-NMR study of the impact of high pressure and thermal processing on cell membrane integrity of onions

    NARCIS (Netherlands)

    Gonzalez, M.E.; Barrett, D.M.; McCarthy, M.J.; Vergeldt, F.J.; Gerkema, E.; Matser, A.M.; As, van H.

    2010-01-01

    Proton nuclear magnetic resonance (1H-NMR) relaxometry was used to study the effects of high pressure and thermal processing on membrane permeability and cell compartmentalization, important components of plant tissue texture. High pressure treated onions were subjected to pressure levels from 20 to

  10. Small-angle neutron scattering study of high-pressure sintered detonation nanodiamonds

    International Nuclear Information System (INIS)

    Kidalov, S. V.; Shakhov, F. M.; Lebedev, V. T.; Orlova, D. N.; Grushko, Yu. S.

    2011-01-01

    The structure of detonation diamonds sintered at a high pressure (7 GPa) and temperatures of 1200–1700°C has been investigated by small-angle neutron scattering. It is shown that sintering leads to an increase in the particle size from 6 to 30 nm and established that this increase is due to the chainlike oriented attachment of particles. This study supplements the oriented-attachment model, which was suggested based on the X-ray diffraction spectra of detonation nanodiamonds (DNDs) sintered under the same conditions.

  11. High-pressure nuclear magnetic resonance studies of fuel cell membranes

    Science.gov (United States)

    Mananga, Eugene Stephane

    This thesis focuses on the use of high pressure NMR to study transport properties in electrolyte membranes used for fuel cells. The main concern is in studying the self-diffusion coefficients of ions and molecules in membranes and solutions, which can be used to characterize electrolytes in fuel cells. For this purpose, a high-pressure fringe field NMR method to study transport properties in material systems useful for fuel cell and battery electrolytes, was designed, developed, and implemented. In this investigation, pressure is the thermodynamic variable to obtain additional information about the ionic transport process, which could yield the crucial parameter, activation volume. Most of the work involves proton NMR, with additional investigations of others nuclei, such as fluorine, phosphorus and lithium. Using the FFG method, two fuel cell membrane types (NAFION-117, SPTES), and different dilutions of phosphoric acid were investigated, as was LiTf salt in Diglyme solution, which is used as a lithium battery electrolyte. In addition to high-pressure NMR diffusion measurements carried out in the fringe field gradient for the investigation of SPTES, pulse field gradient spin echo NMR was also used to characterize the water diffusion, in addition to measuring diffusion rates as a function of temperature. This second method allows us to measure distinct diffusion coefficients in cases where the different nuclear (proton) environments can be resolved in the NMR spectrum. Polymer electrolyte systems, in which the mobility of both cations and anions is probed by NMR self-diffusion measurements using standard pulsed field gradient methods and static gradient measurements as a function of applied hydrostatic pressure, were also investigated. The material investigated is the low molecular weight liquid diglyme/LiCF3SO3 (LiTf) complexes which can be used as electrolytes in lithium batteries. Finally, high-pressure diffusion coefficient measurements of phosphoric acid in

  12. High Pressure X-ray Diffraction Study on Icosahedral Boron Arsenide (B12As2)

    Energy Technology Data Exchange (ETDEWEB)

    J Wu; H Zhu; D Hou; C Ji; C Whiteley; J Edgar; Y Ma

    2011-12-31

    The high pressure properties of icosahedral boron arsenide (B12As2) were studied by in situ X-ray diffraction measurements at pressures up to 25.5 GPa at room temperature. B12As2 retains its rhombohedral structure; no phase transition was observed in the pressure range. The bulk modulus was determined to be 216 GPa with the pressure derivative 2.2. Anisotropy was observed in the compressibility of B12As2-c-axis was 16.2% more compressible than a-axis. The boron icosahedron plays a dominant role in the compressibility of boron-rich compounds.

  13. Small-angle neutron scattering study of high-pressure sintered detonation nanodiamonds

    Energy Technology Data Exchange (ETDEWEB)

    Kidalov, S. V.; Shakhov, F. M., E-mail: fedor.shakhov@mail.ioffe.ru [Ioffe Physical-Technical Institute of the Russian Academy of Sciences (Russian Federation); Lebedev, V. T.; Orlova, D. N.; Grushko, Yu. S. [Russian Academy of Sciences, Konstantinov St. Petersburg Nuclear Physics Institute (Russian Federation)

    2011-12-15

    The structure of detonation diamonds sintered at a high pressure (7 GPa) and temperatures of 1200-1700 Degree-Sign C has been investigated by small-angle neutron scattering. It is shown that sintering leads to an increase in the particle size from 6 to 30 nm and established that this increase is due to the chainlike oriented attachment of particles. This study supplements the oriented-attachment model, which was suggested based on the X-ray diffraction spectra of detonation nanodiamonds (DNDs) sintered under the same conditions.

  14. Microstructure of calcite deformed by high-pressure torsion: An X-ray line profile study

    Science.gov (United States)

    Schuster, Roman; Schafler, Erhard; Schell, Norbert; Kunz, Martin; Abart, Rainer

    2017-11-01

    Calcite aggregates were deformed to high strain using high-pressure torsion and applying confining pressures of 1-6 GPa and temperatures between room temperature and 450 °C. The run products were characterized by X-ray diffraction, and key microstructural parameters were extracted employing X-ray line profile analysis. The dominant slip system was determined as r { 10 1 bar 4 } ⟨ 2 bar 021 ⟩ with edge dislocation character. The resulting dislocation density and the size of the coherently scattering domains (CSD) exhibit a systematic dependence on the P-T conditions of deformation. While high pressure generally impedes recovery through reducing point defect mobility, the picture is complicated by pressure-induced phase transformations in the CaCO3 system. Transition from the calcite stability field to those of the high-pressure polymorphs CaCO3-II, CaCO3-III and CaCO3-IIIb leads to a change of the microstructural evolution with deformation. At 450 °C and pressures within the calcite stability field, dislocation densities and CSD sizes saturate at shear strains exceeding 10 in agreement with earlier studies at lower pressures. In the stability field of CaCO3-II, the dislocation density exhibits a more complex behavior. Furthermore, at a given strain and strain rate, the dislocation density increases and the CSD size decreases with increasing pressure within the stability fields of either calcite or of the high-pressure polymorphs. There is, however, a jump from high dislocation densities and small CSDs in the upper pressure region of the calcite stability field to lower dislocation densities and larger CSDs in the low-pressure region of the CaCO3-II stability field. This jump is more pronounced at higher temperatures and less so at room temperature. The pressure influence on the deformation-induced evolution of dislocation densities implies that pressure variations may change the rheology of carbonate rocks. In particular, a weakening is expected to occur at

  15. Neutron scattering study of structure and dynamics of ammonium halides under high pressure

    International Nuclear Information System (INIS)

    Kozlenko, D.P.; Balagurov, A.M.; Savenko, B.N.; Glazkov, V.P.; Somenkov, V.A.; Hull, S.

    1999-01-01

    Complete text of publication follows. Structural changes in ammonium halides ND 4 Cl, ND 4 Br and ND 4 F at pressures up to 40 kbar and ND 4 I at pressures up to 86 kbar have been studied bz means of neutron diffraction at room temperature. The pressure dependencies of the lattice parameter a and the deuterium position parameter u were obtained. It was found that the order - disorder II-IV phase transition in ND 4 Br and ND 4 Cl occurs at equal critical values of u, u cr =0.152(2). For ND 4 F, u is initially higher than u cr and only the ordered CsCl type phase III exists at high pressure. For ND 4 I, no II-IV phase transition was observed. A phase transition into the recently discovered high pressure phase V was detected in ND 4 I at 80 4 I(V) was found to be the same as the structure of the low temperature phase ND 4 I(III) - tetragonal one with antiparallel ordering of ammonium ions, space group P4/nmm. Vibrational spectra of NH 4 I and HN 4 F have been studied by means of incoherent inelastic neutron scattering at pressure up to 40 kbar. Vibration and transverse optical (TO) modes frequencies as functions of pressure were obtained. Both frequencies increase under pressure. (author)

  16. Synthesis and high (pressure, temperature) stability of ZnTiO3 polymorphs studied by Raman spectroscopy

    Science.gov (United States)

    Bernert, T.; Ruiz-Fuertes, J.; Bayarjargal, L.; Winkler, B.

    2015-05-01

    The phase-purity of ilmenite-type ZnTiO3 prepared by the ceramic method was investigated in dependence of the conditions during ball milling. The previously proposed addition of 2 ml ethanol to the starting materials led to a significant contamination of the product phase after a subsequent sintering process at 1073 K. However, by omitting ethanol this synthesis route led to a phase-pure sample of ZnTiO3 as confirmed by X-ray powder diffraction and Raman spectroscopy. High-temperature high-pressure experiments gave an ilmenite-type to perovskite-type phase boundary with a slope of dT/dP∼-135 K GPa-1 crossing ambient temperature conditions at ∼ 24 GPa in good agreement with previous calculations. Room-temperature high-pressure Raman spectroscopy experiments have shown the stability of the ilmenite-type phase up to a pressure of at least 38.5 GPa, the highest pressure applied in this study, indicating the presence of a kinetic barrier in this phase transition. The synthesis of ferroelectric LiNbO3-type ZnTiO3 was confirmed by second harmonic generation.

  17. Risk Associated With The Decompression Of High Pressure High Temperature Fluids - Study On Black Oil

    DEFF Research Database (Denmark)

    Figueroa, D. C.; Fosbøl, P. L.; Thomsen, K.

    2015-01-01

    Fluids produced from deep underground reservoirs may result in exponential increase in temperature. It is a consequence of adiabatic fluid decompression from the inverse Joule Thomson Effect (JTE). The phenomenon requires analysis in order to avoid any operational risks. This study evaluates...... the JTE upon decompression of black oil in high pressure-high temperature reservoirs. Also the effect caused by the presence of water and brine on the black oil is studied. The final temperature is calculated from the corresponding energy balance at isenthalpic and non-isenthalpic conditions. It is found...... as well, but the increase is less. The effect of water is studied at different water fractions; it results in lower increase of the final temperature than observed for black oil. The presence of brine in black oil is also studied at different brine fractions. The addition of brine increases the final...

  18. Study of the thermohydraulics of CO2 discharge from a high pressure reservoir

    NARCIS (Netherlands)

    Ahmad, M.; Osch, M.B.V.; Buit, L.; Florisson, O.; Hulsbosch-Dam, C.; Spruijt, M.; Davolio, F.

    2013-01-01

    An experimental test set up has been constructed to carry out controlled CO2 release experiments from a high pressure vessel. The test set up is made up of a 500l stainless steel vessel where CO2 can be introduced up to high pressures and where controlled releases can be conducted. The work

  19. PREFACE: Rheology and Elasticity Studies at Ultra-High Pressures and Temperatures

    Science.gov (United States)

    Liu, Haozhe; Wenk, Hans-Rudolf; Duffy, Thomas S.

    2006-06-01

    One of the major goals of geophysical research is to understand deformation in the deep Earth. The COMPRES (Consortium for Materials Properties Research in Earth Sciences) workshop on `Rheology and Elasticity Studies at Ultra-High Pressures and Temperatures' was held on 21-23 October 2005 at the Advanced Photon Source, Argonne National Laboratory, organized by Haozhe Liu, Hans-Rudolf Wenk and Thomas S Duffy, and provided an opportunity to assemble more than 50 scientists from six countries. Experts in diamond anvil cell (DAC) design, large-volume high-pressure apparatus and data analysis defined the current state of ultra-high pressure deformation studies and explored initiatives to push the technological frontier. The DAC, when used in radial diffraction geometry, emerges as a powerful tool for investigation of plasticity and elasticity of materials at high pressures. More information regarding this workshop can be found at the website: http://www.hpcat.aps.anl.gov/Hliu/Workshop/Index1.htm. In this special issue of Journal of Physics: Condensed Matter, 17 manuscripts review the state-of-the-art and we hope they will stimulate researchers to participate in this field and take it forward to a new level. A major incentive for high-pressure research has been the need of geophysicists to understand composition, physical properties and deformation in the deep Earth in order to interpret the macroscopically observed seismic anisotropy. In the mantle and core, materials deform largely in a ductile manner at low stresses and strain rates. From observational inferences and experiments at lower pressures, it is considered plausible that deformation occurs in the field of dislocation creep or diffusion creep and deformation mechanisms depend in a complex way on stress, strain rate, pressure, temperature, grain size and hydration state. With novel apparatus such as the rotational Drickamer press or deformation DIA (D-DIA) multianvil apparatus, large volumes (approximately 10

  20. Parametric Study of Pulse-Combustor-Driven Ejectors at High-Pressure

    Science.gov (United States)

    Yungster, Shaye; Paxson, Daniel E.; Perkins, Hugh D.

    2015-01-01

    Pulse-combustor configurations developed in recent studies have demonstrated performance levels at high-pressure operating conditions comparable to those observed at atmospheric conditions. However, problems related to the way fuel was being distributed within the pulse combustor were still limiting performance. In the first part of this study, new configurations are investigated computationally aimed at improving the fuel distribution and performance of the pulse-combustor. Subsequent sections investigate the performance of various pulse-combustor driven ejector configurations operating at highpressure conditions, focusing on the effects of fuel equivalence ratio and ejector throat area. The goal is to design pulse-combustor-ejector configurations that maximize pressure gain while achieving a thermal environment acceptable to a turbine, and at the same time maintain acceptable levels of NOx emissions and flow non-uniformities. The computations presented here have demonstrated pressure gains of up to 2.8%.

  1. High pressure superconductivity in iron-based layered compounds studied using designer diamonds.

    Science.gov (United States)

    Tsoi, Georgiy; Stemshorn, Andrew K; Vohra, Yogesh K; Wu, Phillip M; Hsu, F C; Huang, Y L; Wu, M K; Yeh, K W; Weir, Samuel T

    2009-06-10

    High pressure superconductivity in iron-based superconductor FeSe(0.5)Te(0.5) has been studied up to 15 GPa and 10 K using an eight probe designer diamond anvil in a diamond anvil cell device. Four probe electrical resistance measurements show the onset of superconductivity (T(c)) at 14 K at ambient pressure with T(c) increasing with increasing pressure to 19 K at a pressure of 3.6 GPa. At higher pressures beyond 3.6 GPa, T(c) decreases and extrapolation suggests non-superconducting behavior above 10 GPa. The loss of superconductivity coincides with the pressure induced disordering of the Fe(SeTe)(4) tetrahedra reported at 11 GPa in x-ray diffraction studies at ambient temperature.

  2. Theoretical Study on Electronic, Optical Properties and Hardness of Technetium Phosphides under High Pressure

    Directory of Open Access Journals (Sweden)

    Shiquan Feng

    2017-06-01

    Full Text Available In this paper, the structural properties of technetium phosphides Tc3P and TcP4 are investigated by first principles at zero pressure and compared with the experimental values. In addition, the electronic properties of these two crystals in the pressure range of 0–40 GPa are investigated. Further, we discuss the change in the optical properties of technetium phosphides at high pressures. At the end of our study, we focus on the research of the hardness of TcP4 at different pressures by employing a semiempirical method, and the effect of pressure on the hardness is studied. Results show that the hardness of TcP4 increases with the increasing pressure, and the influence mechanism of pressure effect on the hardness of TcP4 is also discussed.

  3. High pressure behaviour of uranium dicarbide (UC{sub 2}): Ab-initio study

    Energy Technology Data Exchange (ETDEWEB)

    Sahoo, B. D., E-mail: bdsahoo@barc.gov.in; Mukherjee, D.; Joshi, K. D.; Kaushik, T. C. [Applied Physics Division, Bhabha Atomic Research Centre, Mumbai 400085 (India)

    2016-08-28

    The structural stability of uranium dicarbide has been examined under hydrostatic compression employing evolutionary structure search algorithm implemented in the universal structure predictor: evolutionary Xtallography (USPEX) code in conjunction with ab-initio electronic band structure calculation method. The ab-initio total energy calculations involved for this purpose have been carried out within both generalized gradient approximations (GGA) and GGA + U approximations. Our calculations under GGA approximation predict the high pressure structural sequence of tetragonal → monoclinic → orthorhombic for this material with transition pressures of ∼8 GPa and 42 GPa, respectively. The same transition sequence is predicted by calculations within GGA + U also with transition pressures placed at ∼24 GPa and ∼50 GPa, respectively. Further, on the basis of comparison of zero pressure equilibrium volume and equation of state with available experimental data, we find that GGA + U approximation with U = 2.5 eV describes this material better than the simple GGA approximation. The theoretically predicted high pressure structural phase transitions are in disagreement with the only high experimental study by Dancausse et al. [J. Alloys. Compd. 191, 309 (1993)] on this compound which reports a tetragonal to hexagonal phase transition at a pressure of ∼17.6 GPa. Interestingly, during lowest enthalpy structure search using USPEX, we do not see any hexagonal phase to be closer to the predicted monoclinic phase even within 0.2 eV/f. unit. More experiments with varying carbon contents in UC{sub 2} sample are required to resolve this discrepancy. The existence of these high pressure phases predicted by static lattice calculations has been further substantiated by analyzing the elastic and lattice dynamic stability of these structures in the pressure regimes of their structural stability. Additionally, various thermo-physical quantities such as

  4. Structural and electronic properties of sodium azide at high pressure: A first principles study

    Science.gov (United States)

    Zhang, Meiguang; Yin, Ketao; Zhang, Xinxin; Wang, Hui; Li, Quan; Wu, Zhijian

    2013-05-01

    The structural and electronic properties of NaN3 at high pressures were studied through ab initio calculations. Three new phases with I4/mcm, P6/m and C2/m structure were found to be stable at pressures of 6.5, 58 and 152 GPa, respectively. Similarity of the Raman spectra revealed that the experimental post-α phase should adopt the I4/mcm structure. The calculated insulator-metal transition at 58 GPa directly explained the observed darkening of NaN3 sample at above 50 GPa. The three proposed structures contain azide, N6 hexagon and polymeric nitrogen, respectively. Our finding of the novel N6 hexagon in NaN3 at moderate pressures provides a new view of the pressure-induced polymerization process of metal azides.

  5. High pressure neutron diffraction studies of the magnetic structures of Tb, Ho and Er

    International Nuclear Information System (INIS)

    Kawano, Shinji; Achiwa, Norio; Onodera, Akifumi; Nakai, Yutaka; Lebech, Bente.

    1993-01-01

    Pressure effects of the magnetic structures of Tb, Ho and Er have been studied by neutron diffraction using a newly-developed clamp type pressure cell. For Tb the pressure dependence of the turn angle in a helical phase shows an enhancement of its value, particularly in low temperatures with increasing pressure but no lock-in feature. Linear coefficients of the magnetic transition temperatures to pressure are obtained. For Ho the turn angle is increased by pressure and shows an almost linear temperature dependence at high temperatures and lock-in features at low temperatures. For Er the high pressure results reveal that the transition to a conical structure at low temperatures is suppressed and that a cycloidal structure with a modulation vector Q = 2/7(2π/c) persists down to 4.5 K, similar to a three up four down structure in Tm. (author)

  6. Study of the structure of PyHReO4 under high pressure

    International Nuclear Information System (INIS)

    Kichanov, S. E.; Kozlenko, D. P.; Wasicki, J. W.; Czarnecki, P.; Glazkov, V. P.; Nawrocik, W.; Savenko, B. N.; Lathe, C.

    2007-01-01

    The structure of deuterated pyridinium perrhenate (d 5 PyH)ReO 4 (C 5 D 5 NHReO 4 ) is studied by X-ray diffraction at room temperature and pressures up to 3.5 GPa and by neutron diffraction in the temperature range 10-293 K and at pressures up to 2.0 GPa. Under normal conditions, this compound belongs to the orthorhombic space group Cmc2 1 (ferroelectric phase II). At room temperature and pressures above P > 0.7 GPa, a transition to an orthorhombic phase (paraelectric phase II) is observed. This paraelectric phase is described by the space group Cmcm. At a pressure as high as P = 2.0 GPa, phase I remains stable at temperatures down to 10 K. This fact indicates that the high pressure suppresses the ferroelectric state in deuterated pyridinium perrhenate (d 5 PyH)ReO 4

  7. Chain-length-dependent intermolecular packing in polyphenylenes: a high pressure study

    CERN Document Server

    Heimel, G; Oehzelt, M; Hummer, K; Koppelhuber-Bitschnau, B; Porsch, F; Ambrosch-Draxl, C; Resel, R

    2003-01-01

    We report on pressure-induced structural changes in crystalline oligo(para-phenylenes) containing two to six phenyl rings. The results are discussed with particular emphasis put on the implications these changes in intermolecular distances and molecular arrangement have on important bulk properties of this class of materials, such as optical response and charge transport. We performed energy dispersive x-ray diffraction in a systematic study on polycrystalline powders of biphenyl, para-terphenyl, p-quaterphenyl, p-quinquephenyl and p-sexiphenyl under hydrostatic pressure up to 60 kbar. Revisiting the crystal structures at ambient conditions reveals details in the packing principle. A linear relationship between the density at ambient conditions and the number of phenyl rings is found. High pressure data not only yields pressure-dependent lattice parameters and hints towards pressure-induced changes in the molecular arrangement but also allows for an analysis of the equations of state of these substances as a ...

  8. High-pressure X-ray diffraction study of bulk- and nanocrystalline GaN

    DEFF Research Database (Denmark)

    Jorgensen, J.E.; Jakobsen, J.M.; Jiang, Jianzhong

    2003-01-01

    Bulk- and nanocrystalline GaN have been studied by high-pressure energy-dispersive X-ray diffraction. Pressure-induced structural phase transitions from the wurtzite to the NaCl phase were observed in both materials. The transition pressure was found to be 40 GPa for the bulk-crystalline GaN, while...... the wurtzite phase was retained up to 60 GPa in the case of nanocrystalline GaN. The bulk moduli for the wurtzite phases were determined to be 187 ( 7) and 319 ( 10) GPa for the bulk- and nanocrystalline phases, respectively, while the respective NaCl phases were found to have very similar bulk moduli [ 208...... ( 28) and 206 ( 44) GPa]....

  9. High pressure in-situ X-ray diffraction study on Zn-doped magnetite nanoparticles

    Science.gov (United States)

    Ferrari, S.; Bilovol, V.; Pampillo, L. G.; Grinblat, F.; Errandonea, D.

    2018-03-01

    We have performed high pressure synchrotron X-ray powder diffraction experiments on two different samples of Zn-doped magnetite nanoparticles (formula Fe(3-x)ZnxO4; x = 0.2, 0.5). The structural behavior of then a noparticles was studied up to 13.5 GPa for x = 0.2, and up to 17.4 GPa for x = 0.5. We have found that both systems remain in the cubic spinel structure as expected for this range of applied pressures. The analysis of the unit cell volume vs. pressure results in bulk modulus values lower than in both end-members, magnetite (Fe3O4) and zinc ferrite (ZnFe2O4), suggesting that chemical disorder may favor compressibility, which is expected to improve the increase of the Neel temperature under compression.

  10. Study of Electron Swarm in High Pressure Hydrogen Gas Filled RF Cavities

    International Nuclear Information System (INIS)

    Yonehara, K.; Chung, M.; Jansson, A.; Moretti, A.; Popovic, M.; Tollestrup, A.; Alsharo'a, M.; Johnson, R.P.; Notani, M.; Oka, T.; Wang, H.

    2010-01-01

    A high pressure hydrogen gas filled RF cavity has been proposed for use in the muon collection system for a muon collider. It allows for high electric field gradients in RF cavities located in strong magnetic fields, a condition frequently encountered in a muon cooling channel. In addition, an intense muon beam will generate an electron swarm via the ionization process in the cavity. A large amount of RF power will be consumed into the swarm. We show the results from our studies of the HV RF breakdown in a cavity without a beam and present some results on the resulting electron swarm dynamics. This is preliminary to actual beam tests which will take place late in 2010.

  11. Parametric studies on containment thermal hydraulic loads during high pressure melt ejection in a BWR

    Energy Technology Data Exchange (ETDEWEB)

    Silde, A.; Lindholm, I. [VTT Energy, Espoo (Finland)

    1997-12-01

    The containment thermal hydraulic loads during high pressure melt ejection in a Nordic BWR are studied parametrically with the CONTAIN and the MELCOR codes. The work is part of the Nordic RAK-2 project. The containment analyses were divided into two categories according to composition of the discharged debris: metallic and oxidic debris cases. In the base case with highly metallic debris, all sources from the reactor coolant system to the containment were based on the MELCOR/BH calculation. In the base case with the oxidic debris, the source data was specified assuming that {approx} 15% of the whole core material inventory and 34,000 kg of saturated water was discharged from the reactor pressure vessel (RPV) during 30 seconds. In this case, the debris consisted mostly of oxides. The highest predicted containment pressure peaks were about 8.5 bar. In the scenarios with highly metallic debris source, very high gas temperature of about 1900 K was predicted in the pedestal, and about 1400 K in the upper drywell. The calculations with metallic debris were sensititive to model parameters, like the particle size and the parameters, which control the chemical reaction kinetics. In the scenarios with oxidic debris source, the predicted pressure peaks were comparable to the cases with the metallic debris source. The maximum gas temperatures (about 450-500 K) in the containment were, however, significantly lower than in the respective metallic debris case. The temperatures were also insensitive to parametric variations. In addition, one analysis was performed with the MELCOR code for benchmarking of the MELCOR capabilities against the more detailed CONTAIN code. The calculations showed that leak tightness of the containment penetrations could be jeopardized due to high temperature loads, if a high pressure melt ejection occurred during a severe accident. Another consequence would be an early containment venting. (au). 28 refs.

  12. Neutron and high-pressure X-ray diffraction study of hydrogen-bonded ferroelectric rubidium hydrogen sulfate.

    Science.gov (United States)

    Binns, Jack; McIntyre, Garry J; Parsons, Simon

    2016-12-01

    The pressure- and temperature-dependent phase transitions in the ferroelectric material rubidium hydrogen sulfate (RbHSO 4 ) are investigated by a combination of neutron Laue diffraction and high-pressure X-ray diffraction. The observation of disordered O-atom positions in the hydrogen sulfate anions is in agreement with previous spectroscopic measurements in the literature. Contrary to the mechanism observed in other hydrogen-bonded ferroelectric materials, H-atom positions are well defined and ordered in the paraelectric phase. Under applied pressure RbHSO 4 undergoes a ferroelectric transition before transforming to a third, high-pressure phase. The symmetry of this phase is revised to the centrosymmetric space group P2 1 /c, resulting in the suppression of ferroelectricity at high pressure.

  13. Computational study of a High Pressure Turbine Nozzle/Blade Interaction

    Science.gov (United States)

    Kopriva, James; Laskowski, Gregory; Sheikhi, Reza

    2015-11-01

    A downstream high pressure turbine blade has been designed for this study to be coupled with the upstream uncooled nozzle of Arts and Rouvroit [1992]. The computational domain is first held to a pitch-line section that includes no centrifugal forces (linear sliding-mesh). The stage geometry is intended to study the fundamental nozzle/blade interaction in a computationally cost efficient manner. Blade/Nozzle count of 2:1 is designed to maintain computational periodic boundary conditions for the coupled problem. Next the geometry is extended to a fully 3D domain with endwalls to understand the impact of secondary flow structures. A set of systematic computational studies are presented to understand the impact of turbulence on the nozzle and down-stream blade boundary layer development, resulting heat transfer, and downstream wake mixing in the absence of cooling. Doing so will provide a much better understanding of stage mixing losses and wall heat transfer which, in turn, can allow for improved engine performance. Computational studies are performed using WALE (Wale Adapted Local Eddy), IDDES (Improved Delayed Detached Eddy Simulation), SST (Shear Stress Transport) models in Fluent.

  14. A Synchrotron Mössbauer Spectroscopy Study of a Hydrated Iron-Sulfate at High Pressures

    Science.gov (United States)

    Perez, T. M.; Finkelstein, G. J.; Solomatova, N. V.; Jackson, J. M.

    2017-12-01

    Szomolnokite is a monohydrated ferrous iron sulfate mineral, FeSO4*H2O, where the ferrous iron atoms are in octahedral coordination with four corners shared with SO4 and two with H2O. While somewhat rare on Earth, szomolnokite has been detected on the surface of Mars along with several other hydrated sulfates and suggested to occur near the surface of Venus [1,2]. It is not clear if these sulfates are a result of reactions occurring at depth driven by changes in the behavior of iron in the sulfate. To date, only a few high-pressure studies have been conducted on hydrated iron sulfates using Mössbauer spectroscopy. Our study represents a first step towards understanding of the electronic environment of iron in a monohydrated sulfate at pressure. Using a hydrostatic helium pressure-transmitting medium, the pressure dependence of iron's site-specific behavior in a synthetic szomolnokite powdered sample was explored up to about 100 GPa with time-resolved synchrotron Mössbauer spectroscopy at the Advanced Photon Source of Argonne National Laboratory. At 1 bar, the Mössbauer spectrum is well described by three Fe2+-like sites, consistent with conventional Mössbauer spectra reported in Dyar et al. [3]. At pressures up to 20 GPa, changes in the hyperfine parameters are most likely due to a structural phase transition. Above this pressure, a fourth site is required to explain the time-spectra. Changes in the electronic configuration of iron, such as those due to a phase transition and/or a spin crossover, will affect the material's compressibility and transport properties. We will compare our high-pressure trends with those of other iron-bearing phases and discuss the relative influence on the dynamics of terrestrial planetary interiors. 1. Bishop et al. (2014) What Lurks in the Martian Rocks and Soil? Investigations of Sulfates, Phosphates, and Perchlorates. Spectral and thermal properties of perchlorate salts and implications for Mars. Am. Min. 99(8-9), 1580

  15. High-pressure crystallography.

    Science.gov (United States)

    McMahon, Malcolm I

    2012-01-01

    The ability of pressure to change inter-atomic distances strongly leads to a wide range of pressure-induced phenomena at high pressures: for example metallisation, amorphisation, superconductivity and polymerisation. Key to understanding these phenomena is the determination of the crystal structure using x-ray or neutron diffraction. The tools necessary to compress matter above 1 million atmospheres (1 Megabar or 100 GPa) were established by the mid 1970s, but it is only since the early 1990s that we have been able to determine the detailed crystal structures of materials at such pressures. In this chapter I briefly review the history of high-pressure crystallography, and describe the techniques used to obtain and study materials at high pressure. Recent crystallographic studies of elements are then used to illustrate what is now possible using modern detectors and synchrotron sources. Finally, I speculate as to what crystallographic studies might become possible over the next decade.

  16. Microstructure and spectroscopy studies on cubic boron nitride synthesized under high-pressure conditions

    International Nuclear Information System (INIS)

    Nistor, L C; Nistor, S V; Dinca, G; Georgeoni, P; Landuyt, J van; Manfredotti, C; Vittone, E

    2002-01-01

    High-resolution electron microscopy (HREM) studies of the microstructure and specific defects in hexagonal boron nitride (h-BN) precursors and cubic boron nitride (c-BN) crystals made under high-pressure high-temperature conditions revealed the presence of half-nanotubes at the edges of the h-BN particles. Their sp 3 bonding tendency could strongly influence the nucleation rates of c-BN. The atomic resolution at extended dislocations was insufficient to allow us to determine the stacking fault energy in the c-BN crystals. Its mean value of 191 pm, 15 mJ m -2 is of the same order of magnitude as that of diamond. High-frequency (94 GHz) electron paramagnetic resonance studies on c-BN single crystals have produced new data on the D1 centres associated with the boron species. Ion-beam-induced luminescence measurements have indicated that c-BN is a very interesting luminescent material, which is characterized by four luminescence bands and exhibits a better resistance to ionizing radiation than CVD diamond

  17. Microstructure and spectroscopy studies on cubic boron nitride synthesized under high-pressure conditions

    Energy Technology Data Exchange (ETDEWEB)

    Nistor, L C [National Institute for Materials Physics, Bucharest (Romania); Nistor, S V [National Institute for Materials Physics, Bucharest (Romania); Dinca, G [Dacia Synthetic Diamonds Factory, Bucharest (Romania); Georgeoni, P [Dacia Synthetic Diamonds Factory, Bucharest (Romania); Landuyt, J van [University of Antwerpen - RUCA, EMAT, Antwerpen (Belgium); Manfredotti, C [Experimental Physics Department, University of Turin, Turin (Italy); Vittone, E [Experimental Physics Department, University of Turin, Turin (Italy)

    2002-11-11

    High-resolution electron microscopy (HREM) studies of the microstructure and specific defects in hexagonal boron nitride (h-BN) precursors and cubic boron nitride (c-BN) crystals made under high-pressure high-temperature conditions revealed the presence of half-nanotubes at the edges of the h-BN particles. Their sp{sup 3} bonding tendency could strongly influence the nucleation rates of c-BN. The atomic resolution at extended dislocations was insufficient to allow us to determine the stacking fault energy in the c-BN crystals. Its mean value of 191 pm, 15 mJ m{sup -2} is of the same order of magnitude as that of diamond. High-frequency (94 GHz) electron paramagnetic resonance studies on c-BN single crystals have produced new data on the D1 centres associated with the boron species. Ion-beam-induced luminescence measurements have indicated that c-BN is a very interesting luminescent material, which is characterized by four luminescence bands and exhibits a better resistance to ionizing radiation than CVD diamond.

  18. High-pressure high-temperature rheological studies of colloidal suspensions with carbon nanotube

    Science.gov (United States)

    Baby, Anoop; Sadr, Reza; Yarc, Rommel; Amani, Mahmood

    2017-11-01

    Selection of the drilling fluid, drilling mud, is vital in minimizing the cost and time required for the drilling in oil fields. Drilling mud aids in cooling, lubricating drilling bit, removing the debries from the drill bore and maintaining the wellbore stability. Owing to the enhanced thermo-physical properties and stable nature, suspensions of nanoparticles have been suggested for drilling fluids. High-pressure and high-temperature rheology of a nanomud suspension (nano particles suspended in a mud solution) is studied here. The nanomud is prepared by dispersing a water-based drilling mud suspension (water with 1% Bentonite and 7% Barite particles) with multi-walled carbon nanotubes, MWCNT. The effect of pressure, temperature, and shear rate are independently studied for the various particle loading of the nanoparticles. Viscosity values are measured at a maximum pressure of 170MPa with temperatures ranging from ambient to 180oC. The effect of MWCNT concentration and variation in shear rate are also investigated A shear thinning non-Newtonian behavior is observed for the basemud and the nanomud samples for all cases. The basemud showed an increase in viscosity with an increase in pressure. However, with MWCNT particle addition, this trend is observed to have reversed.

  19. Microstructure and spectroscopy studies on cubic boron nitride synthesized under high-pressure conditions

    CERN Document Server

    Nistor, L C; Dinca, G; Georgeoni, P; Landuyt, J V; Manfredotti, C; Vittone, E

    2002-01-01

    High-resolution electron microscopy (HREM) studies of the microstructure and specific defects in hexagonal boron nitride (h-BN) precursors and cubic boron nitride (c-BN) crystals made under high-pressure high-temperature conditions revealed the presence of half-nanotubes at the edges of the h-BN particles. Their sp sup 3 bonding tendency could strongly influence the nucleation rates of c-BN. The atomic resolution at extended dislocations was insufficient to allow us to determine the stacking fault energy in the c-BN crystals. Its mean value of 191 pm, 15 mJ m sup - sup 2 is of the same order of magnitude as that of diamond. High-frequency (94 GHz) electron paramagnetic resonance studies on c-BN single crystals have produced new data on the D1 centres associated with the boron species. Ion-beam-induced luminescence measurements have indicated that c-BN is a very interesting luminescent material, which is characterized by four luminescence bands and exhibits a better resistance to ionizing radiation than CVD di...

  20. The use of on-line ion chromatography for high temperature and high pressure reaction studies

    International Nuclear Information System (INIS)

    Lynch, G.J.

    1993-10-01

    This paper describes the use of on-line ion chromatography as a tool for chemistry reaction studies in small volume systems. The technique was used to study chemistry behavior in a high temperature and high pressure autoclave system. A dual analyzer, multi-channel on-line ion chromatograph (IC) was configured to automate the sampling and analysis. Analytical channels were set up for analysis of inorganic anions, monovalent cations, conductivity, and pH. Conductivity and pH were measured using the IC as a flow injection analyzer. Use of the IC system provides significant advantages over conventional sampling and analysis techniques: Reduction in sample volume, a closed sampling system that protects air or light sensitive analytes from breakdown, around-the-clock test performance combined with automatic calibration and quality control checking, and detection and tracking of reaction products or unexpected contaminants. Methods used to correct measured concentrations for the effects of sampling and for calculation of control chemical loss half-lives are presented. A limited evaluation of the flow injection analysis methods for conductivity and pH is provided

  1. Study of discharges produced by surface waves under medium and high pressure: application to chemical analysis

    International Nuclear Information System (INIS)

    Laye epouse Granier, Agnes

    1986-01-01

    This report deals with the study of microwave discharges produced in argon gas by surface waves in the 20-760 Torr pressure range. Application to chemical analysis by emission optical spectroscopy is also investigated. First of all we study the propagation of a surface wave in a bounded plasma in which the effective collision frequency for momentum transfer ν is higher than the excitation one. The axial electron density profile is determined from two diagnostic techniques, i.e., phase variations of the wave field and Stark broadening of H β line. Then we deduce the discharge characteristics ν, θ (maintaining power of an electron-ion pair) and E eff (effective electric field for discharge sustaining) from the electron density profile. Then an energy balance of the discharge is developed. It explains the change of operating conditions in the 20-50 Torr range. At low pressure the discharge is governed by ambipolar diffusion whereas at high pressure, the electrons are mainly lost by volume recombination of Ar 2 + . Finally, we report on chemical analysis experiment of gases (optimum sensibility in found near 100 Torr) and of metallic solutions sprayed by a graphite oven. Performances of such a design and ICP plasma torches are compared. (author) [fr

  2. Study of a High-Pressure External Gear Pump with a Computational Fluid Dynamic Modeling Approach

    Directory of Open Access Journals (Sweden)

    Emma Frosina

    2017-07-01

    Full Text Available A study on the internal fluid dynamic of a high-pressure external gear pump is described in this paper. The pump has been analyzed with both numerical and experimental techniques. Starting from a geometry of the pump, a three-dimensional computational fluid dynamics (CFD model has been built up using the commercial code PumpLinx®. All leakages have been taken into account in order to estimate the volumetric efficiency of the pump. Then the pump has been tested on a test bench of Casappa S.p.A. Model results like the volumetric efficiency, absorbed torque, and outlet pressure ripple have been compared with the experimental data. The model has demonstrated the ability to predict with good accuracy the performance of the real pump. The CFD model has been also used to evaluate the effect on the pump performance of clearances in the meshing area. With the validated model the pressure inside the chambers of both driving and driven gears have been studied underlining cavitation in meshing fluid volume of the pump. For this reason, the model has been implemented in order to predict the cavitation phenomena. The analysis has allowed the detection of cavitating areas, especially at high rotation speeds and delivery pressure. Isosurfaces of the fluid volume have been colored as a function of the total gas fraction to underline where the cavitation occurs.

  3. High pressure {mu}SR studies: rare earths and related materials

    Energy Technology Data Exchange (ETDEWEB)

    Kalvius, G.M., E-mail: kalvius@ph.tum.de; Schreier, E. [Technical University Munich, Physics Department (Germany)], E-mail: kalvius@ph.tum.de; Ekstroem, M.; Hartmann, O. [Uppsala University, Physics Department (Sweden); Henneberger, S., E-mail: kalvius@ph.tum.de; Kratzer, A. [Technical University Munich, Physics Department (Germany)], E-mail: kalvius@ph.tum.de; Waeppling, R. [Uppsala University, Physics Department (Sweden); Martin, E., E-mail: kalvius@ph.tum.de; Burghart, F.J. [Technical University Munich, Physics Department (Germany)], E-mail: kalvius@ph.tum.de; Ballou, R.; Deportes, J. [CNRS, Laboratoire Louis Neel (France); Niedermayer, Ch. [University of Constance, Faculty of Physics (Germany)

    2000-11-15

    After a short introduction to {mu}SR with respect to the study of magnetic properties, followed by a brief outline of the principle of the high pressure-low temperature {mu}SR spectrometer installed at the Paul Scherrer Institute, we discuss some measurements on rare earth materials employing this instrument. They are concerned with: (1) The pressure dependence of the spin turning process in ferromagnetic Gd. (2) The volume dependence of the internal magnetic field in the heavy rare earth metals Gd, Dy, and Ho in their ordered magnetic states. (3) The response of the (first order) magnetic transition in the frustrated antiferromagnets of type RMn{sub 2} (R = Y,Gd) to pressure. (4) The variation of magnetic parameters with pressure in La{sub 2}CuO{sub 4} (powder sample), the antiferromagnetic parent compound of the high T{sub C} superconductors of type La{sub 2-x}(Sr, Ba){sub x}CuO{sub 4}. In conclusion a short outlook on further developments is given.

  4. Study on high pressure plasma produced by ArF laser

    OpenAIRE

    Tsuda, Norio; Yamada, Jun

    2004-01-01

    12th International Congress on Plasma Physics, 25-29 October 2004, Nice (France); When an ArF excimer laser beam was focused in a high pressure argon gas from 50 to 130 atm, the plasma development is observed by streak camera from side window of chamber. The high pressure ArF laser plasma develops symmetrically and the plasma produced by ArF excimer laser hardly develops as compared with the plasma produced by XeCl. The photon energy of ArF laser light is higher than the XeCl laser. The trans...

  5. An experimental study on the effects of high-pressure and multiple injection strategies on DI diesel engine emissions

    KAUST Repository

    Yang, Seung Yeon

    2013-03-25

    An experimental study on effects of high-pressure injections in conjunction with split fuel injections were conducted on an AVL single cylinder DI diesel engine. Various injection schemes were studied through the use of an electronically controlled, common rail injection system capable of injection pressures up to 200 MPa and a maximum of six injections per combustion event. Up to 100 MPa of the fuel injection pressure, the higher injection pressures create faster combustion rates that result in the higher in-cylinder gas temperatures as compared to conventional low-pressure fuel injection systems. When applying high-pressure injections, particulate emission reductions of up to 50% were observed with no change in hydrocarbon emissions, reductions of CO emissions and only slightly higher NOx emissions. Over 100 MPa, on the other hand, the higher injection pressures still reduced up to almost zero-level of particulate emission, at the same time that the NO emission is reduced greatly. Under these high-pressure injection conditions, strong correlations between soot and CO emissions were observed, which compete for the oxidizing OH species. Multiple or split high-pressure injections also investigated as a means to decrease particulate emissions. As a result, a four-split injection strategy resulted in a 55% reduction in particulates and with little or no penalty on NOx emissions. The high pressure split injection strategy with EGR was more effective in reducing particulate and CO emissions simultaneously. Copyright © 2013 SAE International and Copyright © 2013 TSAE.

  6. A high pressure device for neutron scattering studies at low temperatures

    International Nuclear Information System (INIS)

    Jansen, E.; Will, G.

    1980-01-01

    A high-pressure device for neutron diffraction experiments up to 6.5 Kbar, suitable also for use at low temperatures, is described. Safety requirements for operation in a reactor hall have been satisfied. Preliminary results of diffraction measurements on CsClO 4 are presented. (author)

  7. High-pressure x-ray studies of the UCo sub 3 B sub 2 compound and ambient magnetic properties

    CERN Document Server

    Sterer, E; Ettedgui, H; Caspi, E N

    2002-01-01

    Substituting B for Co in the strong permanent magnet materials ACo sub 5 (A Ln or U) substantially modifies the magnetic properties as a function of the B/Co ratio. Preliminary neutron diffraction studies on TbCo sub 3 B sub 2 show site-dependent magnetic moments for both the Tb and the Co atoms. The changing interatomic distances and magnetic properties with changing B/Co ratio lead to a rich magnetic phase diagram as a function of pressure. It is our intention to study some of these materials using high-pressure Moessbauer spectroscopy in the future. As a preliminary step it is essential to study the high-pressure crystallographic phase diagram of these materials. This work shows preliminary high-pressure crystallographic results on UCo sub 3 B sub 2 to 42 GPa, indicating a phase transition around 6 GPa.

  8. High pressure waterjets for oil containment in calm and wavy waters; a parametric study

    International Nuclear Information System (INIS)

    Ghaddar, N.K.; Nawwar, A.M.

    1994-01-01

    The use of high pressure waterjets (HPWJ) as oil barriers has been proposed and tested. It has been shown that a series of waterjets directed horizontally above the free water surface provide an effective means of containing or deflecting oil slicks. The waterjets generate a high speed air flow capable of moving the surface layer of the liquid. A numerical model is implemented to study the characteristics of the entrained turbulent air flow using the Spectral Element Method (SEM) and an algebraic turbulent model for the Reynolds stresses. A test of the code is done for turbulent Couette Flow to check the accuracy of the calculated shear stresses against published data. A parametric study is performed to evaluate the HPWJ system performance at various operating and design parameters which include manifold pressure, nozzle flow rate, nozzle characteristics, jet height and surface wave conditions. The total driving shear force and power required for effective containment are used as performance measures. Shear stress and the total driving shear force at the air-liquid interface are calculated over a reference waterjet distance. Performance is measured under calm and wavy sea conditions. It is found that the containment pressure required to generate a given shear force in wavy surface conditions are 30-50% less than those required in calm water. The driving shear force decreases as the jet height above the liquid surface increased. Shear forces also appear to decrease with the reduction of the entrained air flow. The later is governed by nozzle type, spread angle and spacing. The results of the parametric study are consistent with the trends observed experimentally, and could be used in optimising the system design and performance as well as in setting appropriate operational conditions. 12 refs., 10 figs

  9. Techno-economic feasibility study of providing variable frequency drive for high pressure pump, SWRO Plant at NDDP, Kalpakkam

    International Nuclear Information System (INIS)

    Nagaraj, R.; Murugan, V.; Dangore, A.Y.; Thalor, K.L.; Prabakar, S.; Srivastava, V.K.; Tewari, P.K.

    2010-01-01

    The cost of product water is a key factor in determination of acceptability of any desalination system and plant. In case of Sea Water Reverse Osmosis plants, most of the energy consumed is in the form of electricity. The efficiency of the Reverse Osmosis plant primarily lies in optimization of the power consumption. The High Pressure pump is the single major energy consuming equipment with a share of above 75%. Hence reduction in energy consumed by high pressure pump will have a substantial effect on the overall energy consumption. Also the high pressure pump being a high inertia load requires very high torque at the time of starting. This high starting torque requirement results in increased acceleration time of the motor which subsequently increases the strain on the upstream electrical system from motor feeder to transformer. Such starting characteristic necessitates provision of special starting scheme for the high pressure pump motors. Provision of a Variable Frequency Drive can be a solution for both the above problems. This paper studies the techno-economic feasibility of providing variable frequency drive for high pressure pump motor at NDDP, Kalpakkam. (author)

  10. Development of technique for high-pressure single-crystal neutron scattering and its application to studies of magnetic materials

    International Nuclear Information System (INIS)

    Osakabe, Toyotake

    2012-01-01

    In this article, a new high-pressure apparatus for single-crystal magnetic neutron diffraction under 10 GPa is described. First, new hybrid-anvil, which is composed of an opposed pair of a supported SiC anvil and a tungsten carbide (WC) anvil with a center-dimpled culet, is introduced. Next, results of an investigation of pressure-transmitting media are shown. The hydrostaticity of the media is essential for the single-crystal diffraction experiments. Finally, a thermal neutron focusing device with a lot of curved supermirrors is shown. The device can compensate weak magnetic signals from tiny samples in high-pressure cells. As examples of the studies using the apparatus, the high-pressure single-crystal magnetic neutron diffraction experiments on 4f-electron systems PrFe 4 P 12 and HoB 2 C 2 are taken up. (author)

  11. High-pressure structural study of yttrium monochalcogenides from experiment and theory

    DEFF Research Database (Denmark)

    Vaitheeswaran, G.; Kanchana, V.; Svane, A.

    2011-01-01

    High-pressure powder x-ray diffraction experiments using synchrotron radiation are performed on the yttrium monochalcogenides YS, YSe, and YTe up to a maximum pressure of 23 GPa. The ambient NaCl structure is stable throughout the pressure range covered. The bulk moduli are determined to be 93, 82......, and 67 GPa for YS, YSe, and YTe, respectively. First-principles total energy calculations are carried out using the full-potential linear muffin-tin orbital method. The calculated and measured lattice constants and bulk moduli are in good agrement. Under applied pressure, the yttrium monochalcogenides...... are predicted to undergo a structural transition. Assuming that the high-pressure phase corresponds to the CsCl crystal structure, transition pressures of 53, 36, and 14 GPa are found for YS, YSe, and YTe, respectively....

  12. High-pressure studies of uranium and thorium compounds using synchrotron radiation

    International Nuclear Information System (INIS)

    Staun Olsen, J.; Benedict, U.; Dabos, S.; Gerward, L.; Itie, J.P.

    1986-01-01

    This paper reports high-pressure diffraction experiments and absorption-edge measurements on uranium and thorium rocksalt-structure compounds. A description is given of the equipment used in connection with a synchrotron X-ray source. The bulk modulus B 0 and its pressure derivative B' 0 have been determined. Examples of L III absorption edge measurements of UC and UP are given. (orig.)

  13. High-pressure magnetic study of Fe-Ni and Fe-Pt Invar alloys

    Czech Academy of Sciences Publication Activity Database

    Nataf, L.; Decremps, F.; Chervin, J.C.; Mathon, O.; Pascarelli, S.; Kamarád, Jiří; Baudelet,, F.; Congeduti, A.; Itié, J.P.

    2009-01-01

    Roč. 80, č. 13 (2009), 134404/1-134404/6 ISSN 1098-0121 R&D Projects: GA ČR GA202/09/1027 Institutional research plan: CEZ:AV0Z10100521 Keywords : high-pressure effects * Invar * magnetic circular dichroism, * magnetic moments * magnetic transitions * magnetisation * platinum alloys Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.475, year: 2009

  14. High Pressure Biomass Gasification

    Energy Technology Data Exchange (ETDEWEB)

    Agrawal, Pradeep K [Georgia Tech Research Corporation, Atlanta, GA (United States)

    2016-07-29

    According to the Billion Ton Report, the U.S. has a large supply of biomass available that can supplement fossil fuels for producing chemicals and transportation fuels. Agricultural waste, forest residue, and energy crops offer potential benefits: renewable feedstock, zero to low CO2 emissions depending on the specific source, and domestic supply availability. Biomass can be converted into chemicals and fuels using one of several approaches: (i) biological platform converts corn into ethanol by using depolymerization of cellulose to form sugars followed by fermentation, (ii) low-temperature pyrolysis to obtain bio-oils which must be treated to reduce oxygen content via HDO hydrodeoxygenation), and (iii) high temperature pyrolysis to produce syngas (CO + H2). This last approach consists of producing syngas using the thermal platform which can be used to produce a variety of chemicals and fuels. The goal of this project was to develop an improved understanding of the gasification of biomass at high pressure conditions and how various gasification parameters might affect the gasification behavior. Since most downstream applications of synags conversion (e.g., alcohol synthesis, Fischer-Tropsch synthesis etc) involve utilizing high pressure catalytic processes, there is an interest in carrying out the biomass gasification at high pressure which can potentially reduce the gasifier size and subsequent downstream cleaning processes. It is traditionally accepted that high pressure should increase the gasification rates (kinetic effect). There is also precedence from coal gasification literature from the 1970s that high pressure gasification would be a beneficial route to consider. Traditional approach of using thermogravimetric analyzer (TGA) or high-pressure themogravimetric analyzer (PTGA) worked well in understanding the gasification kinetics of coal gasification which was useful in designing high pressure coal gasification processes. However

  15. Dynamic High Pressure Study of Chemistry and Physics of Molecular Materials

    Science.gov (United States)

    Jezowski, Sebastian Ryszard

    Both temperature and pressure control and influence the packing of molecules in crystalline phases. Our molecular simulations indicate that at ambient pressure, the cubic polymorph of tetracyanoethylene, TCNE, is the energetically stable form up to ˜ 160 K. The observed transition from the cubic to the monoclinic polymorph occurs however only at temperatures above ˜ 318 K due to the large transition barrier. The temperature-induced phase transition in TCNE studied with high-resolution IR spectroscopy is explained in terms of the increased vibrational entropy in the crystals of the monoclinic polymorph. Based upon the inverted design of the Merril-Bassett Diamond Anvil Cell, an improved, second generation dynamic Diamond Anvil Cell was developed. Based on the fluorescence of ruby crystals, we were able to demonstrate that the pressure variation range can be further increased at least up to 7 kbar and that the dynamic pressure compression of up to 1400 GPa/s can be achieved. A new class of mechanophoric system, bis-anthracene, BA, and its photoisomer, PI, is shown to respond reversibly to a mild, static pressure induced by a Diamond Anvil Cell as well as to shear deformation based on absorption spectroscopic measurements. The forward reaction occurs upon illumination with light while the back-reaction may be accelerated upon heating or mechanical stress, coupled to a rehybridization on four equivalent carbon atoms. It is an intriguing result as high pressure stabilizes the photodimerized species in related systems. Our molecular volume simulations ruled out significant differences in the volumes between bis-anthracene and its photoisomer. Kinetic absorption measurements at several different pressures reveal a negative volume of activation in the exothermic back-reaction at room temperature. Through a series of temperature-dependent kinetic measurements it is shown that the barrier of activation for the back-reaction is reduced by more than an order of magnitude at

  16. First-principles study of ternary Li-Al-Te compounds under high pressure

    Science.gov (United States)

    Wang, Youchun; Tian, Fubo; Li, Da; Duan, Defang; Xie, Hui; Liu, Bingbing; Zhou, Qiang; Cui, Tian

    2018-02-01

    The ternary Li-Al-Te compounds were investigated by the first-principle evolutionary calculation based on density function theory. Apart from the known structure, I-42d LiAlTe2 and P3m1 LiAlTe2, several new structures were discovered, P-3m1 LiAlTe2, Pnma LiAlTe2, C2/c Li9AlTe2, Immm Li9AlTe2 and P4/mmm Li6AlTe. We determined that the I-42d LiAlTe2 firstly changed to P-3m1 phase at 6 GPa, and then into the Pnma structure at 65 GPa, Pnma phase was stable up at least to 120 GPa. I-42d LiAlTe2 was a pseudo-direct band gap semiconductor, but P-3m1 LiAlT2 was an indirect band gap semiconductor. This may be caused by the pressure effect. Subsequently, it was metallized under pressure. Pnma LiAlTe2 was also metallic at the pressure we studied. C2/c Li9AlTe2 was stable above 4 GPa, then turned into Immm phase at 60 GPa. C2/c Li9AlTe2 was an indirect band gap semiconductor. The results show that P4/mmm Li6AlTe was stable and metallized in the pressure range of 0.7-120 GPa. The calculations of DOS and PDOS indicate that the arrangement of electrons near Fermi energy can be affected by the increase of Li. The calculated ELF results and Bader charge analysis indicate that there was no covalent bond between Al and Te atoms for high-pressure Pnma LiAlTe2, Li9AlTe2 and Li6AlTe. For Li9AlTe2 and Li6AlTe, different from LiAlTe2, Al atoms not connect with Te atoms, but link with Li atoms. The results were further proved by Mulliken population analysis. And the weak covalent bonds between Li and Al atoms stem from the hybridization of Li s and Al p presented in PDOS diagrams. We further deduced that the pressure effect and the increase of Li content may result in the disappearance of Al-Te bonds for Li-Al-Te compound under extreme pressure.

  17. Experimental and Kinetic Modeling Study of C2H2Oxidation at High Pressure

    DEFF Research Database (Denmark)

    Lopez, Jorge Gimenez; Rasmussen, Christian Tihic; Hashemi, Hamid

    2016-01-01

    A detailed chemical kinetic model for oxidation of acetylene at intermediate temperatures and high pressure has been developed and evaluated experimentally. The rate coefficients for the reactions of C2H2 with HO2 and O2 were investigated, based on the recent analysis of the potential energy...... vinyl (reducing conditions) or with OH to form a CHCHOH adduct (stoichiometric to lean conditions). Both C2H3 and CHCHOH then react primarily with O2. The CHCHOH + O2 reaction leads to formation of significant amounts of glyoxal (OCHCHO) and formic acid (HOCHO), and the oxidation chemistry...

  18. Magnetism in Solid Oxygen Studied by High-Pressure Neutron Diffraction

    Science.gov (United States)

    Klotz, Stefan

    2018-03-01

    This article reviews progress achieved over the last 15 years in our understanding of magnetism in solid oxygen under high pressure with a particular emphasis on the contribution of neutron diffraction in the multi-GPa range. The paper highlights the unexpected complexity of magnetic structures in the δ phase at 5-8 GPa, presents data on the pressure dependence of diffuse scattering in β-O2 and discusses potential magnetism in ɛ-O2. High-resolution diffraction data of all three solid phases at ambient pressure are presented.

  19. Study of the magnetic superconductor, Y9Co7, at high pressure and high magnetic field

    International Nuclear Information System (INIS)

    Huang, C.Y.; Olsen, C.E.; Fuller, W.W.; Huang, J.H.; Wolf, S.A.

    1983-01-01

    The electrical resistance and magnetic susceptibility of the magnetic superconductor, Y 9 Co 7 has been measured at pressures up to 20 kbar and in magnetic fields up to 6T. It has been found that pressure suppresses the magnetism resulting in a higher superconducting transition temperature and conclude that Y 9 Co 7 is an itinerant ferromagnet, not a spin-glass. Pressure also sharpens the superconducting transition and increases the critical magnetic field, signifying that the long range ferromagnetic and superconducting order parameters co-exist but vary spatially. For pressures greater than 6 kbar, the magnetoresistance is always positive, further indicating the suppression of magnetism by high pressure. (author)

  20. High pressure in situ diffraction studies of metal-hydrogen systems

    Energy Technology Data Exchange (ETDEWEB)

    Yartys, V.A., E-mail: volodymyr.yartys@ife.no [Institute for Energy Technology, Kjeller NO 2027 (Norway); Norwegian University of Science and Technology, Trondheim NO 7491 (Norway); Denys, R.V. [Institute for Energy Technology, Kjeller NO 2027 (Norway); Karpenko Physico-Mechanical Institute, NAS of Ukraine, Lviv 79601 (Ukraine); Webb, C.J. [Queensland Micro- and Nanotechnology Centre, Griffith University (Australia); Maehlen, J.P. [Institute for Energy Technology, Kjeller NO 2027 (Norway); Gray, E. MacA.; Blach, T. [Queensland Micro- and Nanotechnology Centre, Griffith University (Australia); Isnard, O. [Institute Neel, CNRS/UJF, 38042 Grenoble (France); Barnsley, L.C. [Queensland Micro- and Nanotechnology Centre, Griffith University (Australia)

    2011-09-15

    Research highlights: > CeNi{sub 5}-D{sub 2} and Zr(Fe,Al){sub 2}-D{sub 2} systems were studied by in situ NPD at P up to 1000 bar. > In the hexagonal CeNi{sub 5}D{sub 6.3} deuterium atoms fill three types of interstices. > In the Zr(Fe,Al){sub 2}-based deuterides D atoms occupy the Zr(Fe,Al){sub 2} tetrahedra only D/Zr(Fe,Al){sub 2}, hysteresis and hydrides stability systematically change with Al content. - Abstract: 'Hybrid' hydrogen storage, where hydrogen is stored in both the solid material and as a high pressure gas in the void volume of the tank can improve overall system efficiency by up to 50% compared to either compressed hydrogen or solid materials alone. Thermodynamically, high equilibrium hydrogen pressures in metal-hydrogen systems correspond to low enthalpies of hydrogen absorption-desorption. This decreases the calorimetric effects of the hydride formation-decomposition processes which can assist in achieving high rates of heat exchange during hydrogen loading-removing the bottleneck in achieving low charging times and improving overall hydrogen storage efficiency of large hydrogen stores. Two systems with hydrogenation enthalpies close to -20 kJ/mol H{sub 2} were studied to investigate the hydrogenation mechanism and kinetics: CeNi{sub 5}-D{sub 2} and ZrFe{sub 2-x}Al{sub x} (x = 0.02; 0.04; 0.20)-D{sub 2}. The structure of the intermetallics and their hydrides were studied by in situ neutron powder diffraction at pressures up to 1000 bar and complementary X-ray diffraction. The deuteration of the hexagonal CeNi{sub 5} intermetallic resulted in CeNi{sub 5}D{sub 6.3} with a volume expansion of 30.1%. Deuterium absorption filled three different types of interstices, Ce{sub 2}Ni{sub 2} and Ni{sub 4} tetrahedra, and Ce{sub 2}Ni{sub 3} half-octahedra and was accompanied by a valence change for Ce. Significant hysteresis was observed between deuterium absorption and desorption which profoundly decreased on a second absorption cycle. For the Al

  1. High pressure in situ diffraction studies of metal-hydrogen systems

    International Nuclear Information System (INIS)

    Yartys, V.A.; Denys, R.V.; Webb, C.J.; Maehlen, J.P.; Gray, E. MacA.; Blach, T.; Isnard, O.; Barnsley, L.C.

    2011-01-01

    Research highlights: → CeNi 5 -D 2 and Zr(Fe,Al) 2 -D 2 systems were studied by in situ NPD at P up to 1000 bar. → In the hexagonal CeNi 5 D 6.3 deuterium atoms fill three types of interstices. → In the Zr(Fe,Al) 2 -based deuterides D atoms occupy the Zr(Fe,Al) 2 tetrahedra only D/Zr(Fe,Al) 2 , hysteresis and hydrides stability systematically change with Al content. - Abstract: 'Hybrid' hydrogen storage, where hydrogen is stored in both the solid material and as a high pressure gas in the void volume of the tank can improve overall system efficiency by up to 50% compared to either compressed hydrogen or solid materials alone. Thermodynamically, high equilibrium hydrogen pressures in metal-hydrogen systems correspond to low enthalpies of hydrogen absorption-desorption. This decreases the calorimetric effects of the hydride formation-decomposition processes which can assist in achieving high rates of heat exchange during hydrogen loading-removing the bottleneck in achieving low charging times and improving overall hydrogen storage efficiency of large hydrogen stores. Two systems with hydrogenation enthalpies close to -20 kJ/mol H 2 were studied to investigate the hydrogenation mechanism and kinetics: CeNi 5 -D 2 and ZrFe 2-x Al x (x = 0.02; 0.04; 0.20)-D 2 . The structure of the intermetallics and their hydrides were studied by in situ neutron powder diffraction at pressures up to 1000 bar and complementary X-ray diffraction. The deuteration of the hexagonal CeNi 5 intermetallic resulted in CeNi 5 D 6.3 with a volume expansion of 30.1%. Deuterium absorption filled three different types of interstices, Ce 2 Ni 2 and Ni 4 tetrahedra, and Ce 2 Ni 3 half-octahedra and was accompanied by a valence change for Ce. Significant hysteresis was observed between deuterium absorption and desorption which profoundly decreased on a second absorption cycle. For the Al-modified Laves-type C15 ZrFe 2-x Al x intermetallics, deuteration showed very fast kinetics of H/D exchange

  2. Equations of states for an ionic liquid under high pressure: A molecular dynamics simulation study

    International Nuclear Information System (INIS)

    Ribeiro, Mauro C.C.; Pádua, Agílio A.H.; Gomes, Margarida F.C.

    2014-01-01

    Highlights: • We compare different equation of states, EoS, for an ionic liquid under high pressure. • Molecular dynamics, MD, simulations have been used to evaluate the best EoS. • MD simulations show that a group contribution model can be extrapolated to P ∼ 1.0 GPa. • A perturbed hard-sphere EoS also fits the densities calculated by MD simulations. - Abstract: The high-pressure dependence of density given by empirical equation of states (EoS) for the ionic liquid 1-butyl-3-methylimidazolium trifluoromethanesulfonate (or triflate), [C 4 C 1 im][TfO], is compared with results obtained by molecular dynamics (MD) simulations. Two EoS proposed for [C 4 C 1 im][TfO] in the pressure range of tens of MPa, which give very different densities when extrapolated to pressures beyond the original experiments, are compared with a group contribution model (GCM). The MD simulations provide support that one of the empirical EoS and the GCM is valid in the pressure range of hundreds of MPa. As an alternative to these EoS that are based on modified Tait equations, it is shown that a perturbed hard-sphere EoS based on the Carnahan–Starling–van der Waals equation also fits the densities calculated by MD simulations of [C 4 C 1 im][TfO] up to ∼1.0 GPa

  3. High-pressure measuring cell for Raman spectroscopic studies of natural gas

    DEFF Research Database (Denmark)

    Hansen, Susanne Brunsgaard; Berg, Rolf W.; Stenby, Erling Halfdan

    2001-01-01

    A system for obtaining Raman spectra of gases at high pressure has been constructed. In order to ensure that a natural gas sample is totally representative, a high-pressure gas-measuring cell has been developed, built up by stainless steel fittings and a sapphire tube. The design and construction...... of this cell are described. A perfect pressure seal has been demonstrated up to 15.0 MPaA (MPa absolute). The cell has been successfully used to obtain Raman spectra of natural gas samples. Some of these spectra are presented and assigned. The most remarkable observation in the spectra is that it is possible...... to detect hydrogen sulfide at concentrations of 1-3 mg H2S/Nm(3). An attempt to make a quantitative analysis of natural gas by the so-called "ratio method" is presented. In addition to this, the relative normalized differential Raman scattering cross sections for ethane and i-butane molecules at 8.0 MPa...

  4. First-principles study of the elastic and thermodynamic properties of thorium hydrides at high pressure

    Science.gov (United States)

    Xiao-Lin, Zhang; Yuan-Yuan, Wu; Xiao-Hong, Shao; Yong, Lu; Ping, Zhang

    2016-05-01

    The high pressure behaviors of Th4H15 and ThH2 are investigated by using the first-principles calculations based on the density functional theory (DFT). From the energy-volume relations, the bct phase of ThH2 is more stable than the fcc phase at ambient conditions. At high pressure, the bct ThH2 and bcc Th4H15 phases are more brittle than they are at ambient pressure from the calculated elastic constants and the Poisson ratio. The thermodynamic stability of the bct phase ThH2 is determined from the calculated phonon dispersion. In the pressure domain of interest, the phonon dispersions of bcc Th4H15 and bct ThH2 are positive, indicating the dynamical stability of these two phases, while the fcc ThH2 is unstable. The thermodynamic properties including the lattice vibration energy, entropy, and specific heat are predicted for these stable phases. The vibrational free energy decreases with the increase of the temperature, and the entropy and the heat capacity are proportional to the temperature and inversely proportional to the pressure. As the pressure increases, the resistance to the external pressure is strengthened for Th4H15 and ThH2. Project supported by the Long-Term Subsidy Mechanism from the Ministry of Finance and the Ministry of Education of China.

  5. In-situ study of the thermal properties of hydrate slurry by high pressure DSC

    Energy Technology Data Exchange (ETDEWEB)

    Sari, O.; Hu, J.; Brun, F.; Erbeau, N. [Institute of Thermal Engineering, University of Applied Sciences of Western Switzerland, Yverdon-les-Bains (Switzerland); Homsy, P. [Nestec, Vevey (Switzerland); Logel, J.-C. [Axima Refrigeration, Bischheim (France)

    2008-07-01

    Knowing the enthalpy of hydrate slurry is very essential for energy balance and industrial applications. No direct measurement processes had been developed in this field in the past time. A new experimental method with special device has been developed to carry out on-line measurement of the thermal properties for hydrate slurry under dynamic conditions. With this special device, it is possible to deliver the hydrate slurry to the high pressure DSC (Differential Scanning Calorimetry) directly from the production tank or pipes. Thermal data acquisition will be performed afterwards by DSC. The investigated conditions were at pressure of 30 bar and temperature of {approx}+7 {sup o}C. The dissociation enthalpy of CO{sub 2} hydrate slurry was about 54 kJ/kg, corresponding 10.8% of solid fraction. The on-line measurement results for CO{sub 2} hydrate slurry give a good tendency to apply this phase change slurry to the industrial refrigeration process. (author)

  6. High-pressure neutron and X-ray diffraction study of TmSe

    International Nuclear Information System (INIS)

    Debray, D.; Kahn, R.; Decker, D.L.; Werner, A.; Loewenhaupt, M.; Holland-Moritz, E.

    1981-01-01

    Amongst all the known intermediate valence compounds the monochalcogenide TmSe is unique in the sense that it is the only such compound which shows i) a long-range magnetic order at low temperature, ii) a metal-insulator transition at Tsub(N), and iii) a temperature dependent spin fluctuation energy. To investigate the origin of its unusual physical properties, the authors have carried out high-pressure neutron elastic and inelastic as well as X-ray diffraction measurements on stoichiometric TmSe (a = 5.709A) at ambient and low temperatures. The basic aim of this work was to change, by the application of pressure, parameters which play an important role in the physics of the intermediate valence state and follow through by measuring physical quantities which are influenced by them. (Auth.)

  7. A Numerical Study on the Impeller Meridional Curvature of High Pressure Multistage Pump

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Deok Su; Jean, Sang Gyu; Mamatov, Sanjar [Hyosung Goodsprings, Inc., Busan (Korea, Republic of); Park, Warn Gyu [Pusan Nat’l Univ., Busan (Korea, Republic of)

    2017-07-15

    This paper presents the hydraulic design an impeller and radial diffuser of a high-pressure multistage pump for reverse osmosis. The flow distribution and hydraulic performance for the meridional design of the impeller were analyzed numerically. Optimization was conducted based on the response surface method by varying the hub and shroud meridional curvatures, while maintaining the impeller outlet diameter, outlet width, and eye diameter constant. The analysis results of the head and efficiency with the variation in the impeller meridional profile showed that angle of the front shroud near the impeller outlet (εDs) had the highest effect on head increase, while the hub inlet length (d1i) and shroud curvature (Rds) had the highest effect on efficiency. From the meridional profile variation, an approximately 0.5% increase in efficiency was observed compared with the base model (case 25).

  8. Study on objective functions for the slow shot phase in high-pressure die casting

    Science.gov (United States)

    Frings, Markus; Behr, Marek; Elgeti, Stefanie

    2016-10-01

    High-pressure die casting is an important process in the field of aluminum processing. Especially during the slow shot phase, the process parameters immensely influence the cast part quality. At the current state of the art, the appropriate process parameters are identified based on running-in trials and significant experience. To translate this experience into a mathematical framework is the aim of this work. The idea is to shift the running-in trials to the computer—now in the form of a numerical optimization. In view of the optimization, this paper presents a selection of objective functions. These are assessed with the respect to (1) their suitability as an overall quality measure of the casting process and (2) the extent to which they reflect the goals of the casting process.

  9. High pressure laser plasma studies. [energy pathways in He-Ar gas mixtures at low pressure

    Science.gov (United States)

    Wells, W. E.

    1980-01-01

    The operation of a nuclear pumped laser, operating at a wavelength of 1.79 micron m on the 3d(1/2-4p(3/2) transition in argon with helium-3 as the majority gas is discussed. The energy pathways in He-Ar gas were investigated by observing the effects of varying partial pressures on the emissions of levels lying above the 4p level in argon during a pulsed afterglow. An attempt is made to determine the population mechanisms of the 3d level in pure argon by observing emission from the same transition in a high pressure plasma excited by a high energy electron beam. Both collisional radiative and dissociative recombination are discussed.

  10. The study on density change of carbon dioxide seawater solution at high pressure and low temperature

    International Nuclear Information System (INIS)

    Song, Y.; Chen, B.; Nishio, M.; Akai, M.

    2005-01-01

    It has been widely considered that the global warming, induced by the increasing concentration of carbon dioxide and other greenhouse gases in the atmosphere, is an environmental task affecting the world economic development. In order to mitigate the concentration of CO 2 in the atmosphere, the sequestration of carbon dioxide into the ocean had been investigated theoretically and experimentally over the last 10 years. In addition to ocean dynamics, ocean geological, and biological information on large space and long time scales, the physical-chemistry properties of seawater-carbon dioxide system at high pressure (P>5.0 MPa) and lower temperature (274.15 K 3 , which is approximately same with that of carbon dioxide freshwater solution, the slope of which is 0.275 g/cm 3

  11. High-pressure studies of superconductivity in BiO0. 75F0. 25BiS2

    Indian Academy of Sciences (India)

    Home; Journals; Bulletin of Materials Science; Volume 40; Issue 6. High-pressure studies of superconductivity in BiO 0.75 F 0.25 BiS 2 ... The upper critical field Hc2(0) is greater than 3 T, which is higher than earlier report onthis material. As determined from the M–H curve, both H c 2 and H c 1 decrease under external ...

  12. High-pressure synchrotron studies on TiO sub 2 -II nanocrystallite doped with SnO sub 2

    CERN Document Server

    Luo, W; Zou Guang Tian; Mao Ho Kwang; Wang, Z C; Wang, Y

    2002-01-01

    We have studied the high-pressure and high-temperature behaviour of alpha-PbO sub 2 -type TiO sub 2 -SnO sub 2 (5 mol%) nanocomposite up to 62.3 GPa and 1700 K in a laser-heated diamond-anvil cell by means of synchrotron energy-dispersive x-ray diffraction. We found that it transforms to the baddeleyite phase at 19.4 GPa at room temperature. This phase was stable up to about 40 GPa. At 62.3 GPa and 1700 K, the diffraction pattern showed that there exists another nonquenchable phase. We discussed the mechanisms for these high-pressure transformations in alpha-PbO sub 2 -type TiO sub 2 -SnO sub 2 (5 mol%) nanocomposite.

  13. Differential Thermal Analysis and Dielectric Studies on 2-Methyl-2-Nitro-Propane under High Pressure

    Science.gov (United States)

    Büsing, D.; Jenau, M.; Reuter, J.; Würflinger, A.; Tamarit, J. Li.

    1995-05-01

    Differential thermal analysis and dielectric studies under pressures up to 300 MPa and temperatures of about 200 to 350 K have been performed on 2-methyl-2-nitro-propane (TBN). TBN displays an orientationally disordered phase (ODIC), solid I, and two non-plastic phases, solids II and III. The coexistence region of the plastic phase I increases with increasing pressure, whereas the low-temperature phase II apparently vanishes at a triple point I, II, III, above 300 MPa. The static permittivity increases on freezing, characterizing the solid I as an ODIC phase. In the frame of the Kirkwood-Onsager-Fröhlich theory the g-factor is about unity, discounting specific dielectric correlations. The dielectric behaviour of TBN is similar to previously studied related compounds, such as 2-chloro-2-methyl-propane or 2-brome- 2-methyl-propane

  14. Experimental and Simulation Studies of Strength and Fracture Behaviors of Wind Turbine Bearing Steel Processed by High Pressure Torsion

    Directory of Open Access Journals (Sweden)

    Ning Wang

    2016-12-01

    Full Text Available White structure flaking (WSF has been found to be one of the failure modes in bearing steels under rolling contacts through the formation of cracks associated with a microstructural change called white etching area (WEA. In the present research, the effects of the high-pressure torsion (HPT process on the microstructure and mechanical properties of an AISI 52100 alloy are studied. An annealed AISI 52100 was subjected to high-pressure torsion at room temperature under a pressure of up to ~6 GPa for up to three turns. Finite-element modeling (FEM was used to simulate the process under high-pressure torsion and quasi-constrained conditions to reveal the material property changes occurring in HPT. Scanning electron microscopy and microhardness testing after processing were used to investigate the microstructural and mechanical property evolution of the steel. Strain induced microstructural transformations occur and affect the mechanical properties in a similar way to the well-known white etching area (WEA found beneath the surface of wind turbine bearings. Here, HPT is used to study the feasibility of creating microstructural changes that are similar to WEA. This paper presents the preliminary results of using HPT to produce WEAs.

  15. Determination of the partial pressure of thallium in high-pressure lamp arcs: A comparative study

    International Nuclear Information System (INIS)

    Karabourniotis, D.; Couris, S.; Damelincourt, J.J.; Aubes, M.

    1986-01-01

    The partial pressure of thallium in high-pressure Hg-TlI discharges with different mercury, thallium, and electron pressures has been measured by using the optically thin line Tl 655 nm and the self-reversed line Tl 535 nm. The partial pressure of the arc axis has been measured from the line Tl 655nm. The effective partial pressure has been measured from the self-reversed line Tl 535 nm on the basis of the multiparameter method, and it has been calculated from the known axis pressure of thallium and the calculation of its radial variation by taking into account the chemical reactions. The experimental results confirm the dispersion character of the blue wing of the line Tl 535 nm. The systematic difference obtained between the measured and calculated effective pressure, particularly at the moment of minimum electron density, may be interpreted by deviations from the local thermodynamic equilibrium (LTE) caused by overpopulation of the upper level of the line Tl 535 nm

  16. TEM Studies of B2 Ordered Fe45at%Al Deformed by High Pressure Torsion

    International Nuclear Information System (INIS)

    Mangler, C.; Rentenberger, C.; Karnthaler, H.P.

    2005-01-01

    Full text: It is known that B2 ordered FeAl is very brittle in a wide range of compositions. Therefore strong plastic deformation as cold rolling is usually leading to severe cracking. In order to achieve a high grade of deformation high pressure torsion (HPT) was used to carry out severe plastic deformation while avoiding fracture. During the HPT procedure a sample of polycrystalline Fe45at%Al (diameter ∼ 8 mm and thickness of ∼ 0.8 mm) was rotated 1.25 turns between two anvils under a pressure of 8 GPa at RT. From different areas of the sample (with shear strains up to 4000 %) thin foils were prepared by grinding and electro polishing. Transmission electron microscopic (TEM) investigations were carried out using a Philips CM 200 operating at an acceleration voltage of 200 kV. B2 structured FeAl deforms by the glide of superdislocations. In TEM bright field images elongated areas showing a high density of dislocations were found that lead to small, alternating misorientations between neighbouring bands. Because of the high density of dislocations individual ones can only be resolved in weakbeam dark-field images. The bands have an average width of about 300 nm and lie parallel to a {123} plane, that is one of the liKEXly slip-planes in bcc crystals. No indication of deformation induced disordering was found, which is contrary to L1 2 ordered Cu 3 Au where local complete disordering is observed after HPT deformation. (author)

  17. Creating Binary Cu–Bi Compounds via High-Pressure Synthesis: A Combined Experimental and Theoretical Study

    Energy Technology Data Exchange (ETDEWEB)

    Clarke, Samantha M.; Amsler, Maximilian; Walsh, James P.S.; Yu, Tony; Wang, Yanbin; Meng, Yue; Jacobsen, Steven D.; Wolverton, Chris; Freedman, Danna E. (UC); (CIW); (NWU)

    2017-06-13

    Exploration beyond the known phase space of thermodynamically stable compounds into the realm of metastable materials is a frontier of materials chemistry. The application of high pressure in experiment and theory provides a powerful vector by which to explore this uncharted phase space, allowing discovery of complex new structures and bonding in the solid state. We harnessed this approach for the Cu–Bi system, where the realization of new phases offers potential for exotic properties such as superconductivity. This potential is due to the presence of bismuth, which, by virtue of its status as one of the heaviest stable elements, forms a critical component in emergent materials such as superconductors and topological insulators. To fully investigate and understand the Cu–Bi system, we welded theoretical predictions with experiment to probe the Cu–Bi system under high pressures. By employing the powerful approach of in situ X-ray diffraction in a laser-heated diamond anvil cell (LHDAC), we thoroughly explored the high-pressure and high-temperature (high-PT) phase space to gain insight into the formation of intermetallic compounds at these conditions. We employed density functional theory (DFT) calculations to calculate a pressure versus temperature phase diagram, which correctly predicts that CuBi is stabilized at lower pressures than Cu11Bi7, and allows us to uncover the thermodynamic contributions responsible for the stability of each phase. Detailed comparisons between the NiAs structure type and the two high-pressure Cu–Bi phases, Cu11Bi7 and CuBi, reveal the preference for elemental segregation within the Cu–Bi phases, and highlight the unique channels and layers formed by ordered Cu vacancies. The electron localization function from DFT calculations account for the presence of these “voids” as a manifestation of the lone pair orientation on the Bi atoms. Our study demonstrates the power of joint experimental–computational work in exploring the

  18. High-pressure polymorphs of TbVO4: A Raman and ab initio study

    International Nuclear Information System (INIS)

    Errandonea, D.; Manjón, F.J.; Muñoz, A.; Rodríguez-Hernández, P.; Panchal, V.; Achary, S.N.; Tyagi, A.K.

    2013-01-01

    Highlights: •Three phase transitions are induced in zircon-type TbVO4 at 6.7, 26.7, and 34.4 GPa. •The proposed structural sequence is zircon-scheelite-fergusonite-orthorhombic Cmca. •Scheelite phase is metaestable after decompression. •The equation of states for all phases is reported. •Compressibility is enhanced in the Cmca phase due to f-electron delocalization. -- Abstract: Raman measurements on TbVO 4 show the occurrence of three pressure-induced phase transitions. The first one, an irreversible transition from the zircon to the scheelite structure, occurs beyond 6.7 GPa. In addition, two reversible transformations take place at 26.7 and 34.4 GPa. The last transition was never reported before. The experimental findings are supported by structural and lattice-dynamics calculations that helped us to identify the post-scheelite phase as a monoclinic fergusonite structure. According to the calculations, the third transition involves a symmetry increase. An orthorhombic structure is proposed for the phase found above 34.4 GPa. The results have been compared with previous studies in TbVO 4 and discussed in comparison with related compounds. The calculated equations of state are reported for the different polymorphs of TbVO 4 . A compressibility increase is caused by the third transition. It is associated to a bond-strength decrease, which is related to a coordination increase and a delocalization of Tb f-electrons

  19. High-pressure polymorphs of TbVO{sub 4}: A Raman and ab initio study

    Energy Technology Data Exchange (ETDEWEB)

    Errandonea, D., E-mail: daniel.errandonea@uv.es [Departamento de Física Aplicada-ICMUV, Universidad de Valencia, MALTA Consolider Team, Edificio de Investigación, C/Dr. Moliner 50, Burjassot, 46100 Valencia (Spain); Manjón, F.J. [Instituto de Diseño para la Fabricación y Producción Automatizada, MALTA Consolider Team, Universidad Politécnica de Valencia, Camino de Vera s/n, 46022 Valencia (Spain); Muñoz, A.; Rodríguez-Hernández, P. [Departamento de Física Fundamental II, Instituto de Materiales y Nanotecnología, MALTA Consolider Team, Universidad de La Laguna, La Laguna 38205, Tenerife (Spain); Panchal, V. [Departamento de Física Aplicada-ICMUV, Universidad de Valencia, MALTA Consolider Team, Edificio de Investigación, C/Dr. Moliner 50, Burjassot, 46100 Valencia (Spain); Royal College of Arts, Science and Commerce, Mira Road, Mumbai 401 107 (India); Achary, S.N.; Tyagi, A.K. [Chemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400 085 (India)

    2013-11-15

    Highlights: •Three phase transitions are induced in zircon-type TbVO4 at 6.7, 26.7, and 34.4 GPa. •The proposed structural sequence is zircon-scheelite-fergusonite-orthorhombic Cmca. •Scheelite phase is metaestable after decompression. •The equation of states for all phases is reported. •Compressibility is enhanced in the Cmca phase due to f-electron delocalization. -- Abstract: Raman measurements on TbVO{sub 4} show the occurrence of three pressure-induced phase transitions. The first one, an irreversible transition from the zircon to the scheelite structure, occurs beyond 6.7 GPa. In addition, two reversible transformations take place at 26.7 and 34.4 GPa. The last transition was never reported before. The experimental findings are supported by structural and lattice-dynamics calculations that helped us to identify the post-scheelite phase as a monoclinic fergusonite structure. According to the calculations, the third transition involves a symmetry increase. An orthorhombic structure is proposed for the phase found above 34.4 GPa. The results have been compared with previous studies in TbVO{sub 4} and discussed in comparison with related compounds. The calculated equations of state are reported for the different polymorphs of TbVO{sub 4}. A compressibility increase is caused by the third transition. It is associated to a bond-strength decrease, which is related to a coordination increase and a delocalization of Tb f-electrons.

  20. Tunable high pressure lasers

    Science.gov (United States)

    Hess, R. V.

    1976-01-01

    Atmospheric transmission of high energy CO2 lasers is considerably improved by high pressure operation which, due to pressure broadening, permits tuning the laser lines off atmospheric absorption lines. Pronounced improvement is shown for horizontal transmission at altitudes above several kilometers and for vertical transmission through the entire atmosphere. Applications of tunable high pressure CO2 lasers to energy transmission and to remote sensing are discussed along with initial efforts in tuning high pressure CO2 lasers.

  1. High-pressure apparatus

    NARCIS (Netherlands)

    Schepdael, van L.J.M.; Bartels, P.V.; Berg, van den R.W.

    1999-01-01

    The invention relates to a high-pressure device (1) having a cylindrical high-pressure vessel (3) and prestressing means in order to exert an axial pressure on the vessel. The vessel (3) can have been formed from a number of layers of composite material, such as glass, carbon or aramide fibers which

  2. High-pressure crystallography

    Science.gov (United States)

    Katrusiak, A.

    2008-01-01

    The history and development of high-pressure crystallography are briefly described and examples of structural transformations in compressed compounds are given. The review is focused on the diamond-anvil cell, celebrating its 50th anniversary this year, the principles of its operation and the impact it has had on high-pressure X-ray diffraction.

  3. Human activity under high pressure: A case study on fluctuation scaling of air traffic controller's communication behaviors

    Science.gov (United States)

    Wang, Yanjun; Zhang, Qiqian; Zhu, Chenping; Hu, Minghua; Duong, Vu

    2016-01-01

    Recent human dynamics research has unmasked astonishing statistical characteristics such as scaling behaviors in human daily activities. However, less is known about the general mechanism that governs the task-specific activities. In particular, whether scaling law exists in human activities under high pressure remains an open question. In air traffic management system, safety is the most important factor to be concerned by air traffic controllers who always work under high pressure, which provides a unique platform to study human activity. Here we extend fluctuation scaling method to study air traffic controller's communication activity by investigating two empirical communication datasets. Taken the number of controlled flights as the size-like parameter, we show that the relationships between the average communication activity and its standard deviation in both datasets can be well described by Taylor's power law, with scaling exponent α ≈ 0.77 ± 0.01 for the real operational data and α ≈ 0.54 ± 0.01 for the real-time training data. The difference between the exponents suggests that human dynamics under pressure is more likely dominated by the exogenous force. Our findings may lead to further understanding of human behavior.

  4. Optical Studies at High Pressure on Chromium-Doped Ordered Perovskite Crystals.

    Science.gov (United States)

    Rinzler, Andrew Gabriel

    Pressure dependent luminescence spectra were recorded on the chromium-doped elpasolite crystal Cs_2NaYCl _6:Cr^{3+} at ambient and near liquid nitrogen temperatures in a diamond anvil cell. The broad ^4T_{2g}to ^4A_{2g} fluorescence band of the intrinsically low crystal field compound exhibited a rapid blue shift with increasing pressure. The low temperature measurements yielded enhanced resolution of a ^2E_{g}to ^4A _{2g} phosphorescence appearing at the higher pressures which was interpreted in terms of vibrational modes of the chromium-hexahalide complex. The blue shift of the broad band and the appearance of the structured emission were anticipated by their previous observation in uncorrected luminescence spectra of the chromium doped elpasolites K_2NaGaF_6:Cr ^{3+} and K_2NaScF _6:Cr^{3+}. The spectra of the three crystals were corrected for the spectral response of the corresponding detection system and a transformation was applied to permit interpretation in terms of theoretical lineshape curves. Pressure dependent Raman spectra were recorded on the three crystals. Values of the ratio of the Gruneisen parameter and the bulk modulus were derived for the Raman -active modes. Frequencies of defect modes were determined as a function of pressure in a sample of the K _2NaScF_6:Cr^{3+} crystal with a higher dopant concentration. The photoluminescence lifetime of the chromium -doped chloride elpasolite was measured as a function of temperature, at elevated pressures. The onset of thermal quenching was shifted to higher temperatures with increasing pressure. This behavior was modeled by a pressure dependent activation energy having a rate of change of 1668 +/- 52 cm^{-1}/GPa. Several derivations and calculations were performed. These included: The extraction of pressure-dependent local compressibilities of the chromium-hexahalide complex for the three crystals and the development (within the LCSCC model) of expressions for the pressure derivatives of the effective

  5. High pressure and synchrotron radiation studies of solid state electronic instabilities

    International Nuclear Information System (INIS)

    Pifer, J.H.; Croft, M.C.

    1992-04-01

    This report discusses Eu and General Valence Instabilities; Ce Problem: L 3 Spectroscopy Emphasis; Bulk Property Emphasis; Transition Metal Compound Electronic Structure; Electronic Structure-Phonon Coupling Studies; High Temperature Superconductivity and Oxide Materials; and Novel Materials Collaboration with Chemistry

  6. Impact of condensed matter theories on material studies at high pressures

    International Nuclear Information System (INIS)

    Godwal, B.K.; Rao, R.S.; Sikka, S.K.; Chidambaram, R.

    1997-01-01

    We are vigorously pursuing a program to study the behaviour of materials under pressure for the last three decades. Theoretical component has been an important part of our activity. The initial phase of such efforts was devoted to the development of equation of state models at arbitrary temperature and matter density. With the advent of diamond anvil cell device and improvements of the diagnostic technique in dynamic methods, the focus of our studies switched over to the predictions and interpretations of phase transitions. Many times these have led to intense experimental studies and sometimes helped in resolving the controversies. The introduction of linear methods in electron band theory and availability of supercomputers and parallel processors have given boost to the computational physics, and the efforts are now being extended more and more to the ab-initio molecular dynamics simulations. These simulations have a promise to avoid the tedious search for structural stability by trail and error in phase transition studies under pressure or temperature. The current status of our efforts in this direction will be listed with an illustration on liquid sulphur. Our past work on electronic topological transition in zinc led to many experimental and theoretical investigations. The results of electronic structure changes in similar metal cadmium shall be compared with existing understanding in Zn under pressure. Our studies on other compounds (AuIn 2 , YNi 2 B 2 C), which have also been found to display electronic topological transition under pressure, will be discussed. (author)

  7. High-pressure phases of uranium monophosphide studied by synchrotron x-ray diffraction

    DEFF Research Database (Denmark)

    Olsen, J. Staun; Gerward, Leif; Benedict, U.

    1988-01-01

    X-ray diffraction studies have been performed on UP powder for pressures up to 51 GPa using synchrotron radiation and a diamond-anvil cell. At ambient pressure UP has the rocksalt structure. The bulk modulus has been determined to B0=102(4) GPa and its pressure derivative to B0’=4.0(8). The cubic...

  8. HoB4 at high pressure and low temperature: an experimental and theoretical study

    DEFF Research Database (Denmark)

    Olsen, J. Staun; Waśkowska, A.; Gerward, Leif

    2011-01-01

    Single crystals of HoB4 have been grown and used for synchrotron X-ray diffraction studies at pressures up to 23GPa and temperatures down to 100K. The experimental bulk modulus 195 ± 6GPa is in good agreement with 188.4 and 198.2GPa values calculated in the LSDA and LSDA+U approximations...

  9. Experimental and Kinetic Modeling Study of Methanol Ignition and Oxidation at High Pressure

    DEFF Research Database (Denmark)

    Aranda, V.; Christensen, J. M.; Alzueta, Maria

    2013-01-01

    the conditions studied, the onset temperature for methanol oxidation was not dependent on the stoichiometry, whereas increasing pressure shifted the ignition temperature toward lower values. Model predictions of the present experimental results, as well as rapid compression machine data from the literature, were...

  10. X-ray absorption radiography for high pressure shock wave studies

    Science.gov (United States)

    Antonelli, L.; Atzeni, S.; Batani, D.; Baton, S. D.; Brambrink, E.; Forestier-Colleoni, P.; Koenig, M.; Le Bel, E.; Maheut, Y.; Nguyen-Bui, T.; Richetta, M.; Rousseaux, C.; Ribeyre, X.; Schiavi, A.; Trela, J.

    2018-01-01

    The study of laser compressed matter, both warm dense matter (WDM) and hot dense matter (HDM), is relevant to several research areas, including materials science, astrophysics, inertial confinement fusion. X-ray absorption radiography is a unique tool to diagnose compressed WDM and HDM. The application of radiography to shock-wave studies is presented and discussed. In addition to the standard Abel inversion to recover a density map from a transmission map, a procedure has been developed to generate synthetic radiographs using density maps produced by the hydrodynamics code DUED. This procedure takes into account both source-target geometry and source size (which plays a non negligible role in the interpretation of the data), and allows to reproduce transmission data with a good degree of accuracy.

  11. Studies on a Small Lift Fan Driven by a High Pressure Tip Turbine

    OpenAIRE

    齊藤, 喜夫; SAITOH, Yoshio; 岩瀬, 識; IWASE, Shiki; 松田, 幸雄; MATSUDA, Yukio

    2003-01-01

    NAL has conducted studies on the 'Cluster Fan Engine', a new concept small turbofan engine, for small light aircraft and VTOL airplanes. The Cluster Fan Engine is based on the 'Separated Core Ultrahigh Bypass Engine (SCUHB)', which was also suggested by NAL just one decade ago. The Cluster Fan Engine has many merits, including reliability of operation, flexibility of mounting, maintainability, extremely low development and initial costs, and a wide variety of potential applications. The conc...

  12. Inactivation of orange pectinesterase by combined high-pressure and -temperature treatments: a kinetic study.

    Science.gov (United States)

    Van den Broeck, I; Ludikhuyze, L R; Van Loey, A M; Hendrickx, M E

    2000-05-01

    Pressure and/or temperature inactivation of orange pectinesterase (PE) was investigated. Thermal inactivation showed a biphasic behavior, indicating the presence of labile and stable fractions of the enzyme. In a first part, the inactivation of the labile fraction was studied in detail. The combined pressure-temperature inactivation of the labile fraction was studied in the pressure range 0.1-900 MPa combined with temperatures from 15 to 65 degrees C. Inactivation in the pressure-temperature domain specified could be accurately described by a first-order fractional conversion model, estimating the inactivation rate constant of the labile fraction and the remaining activity of the stable fraction. Pressure and temperature dependence of the inactivation rate constants of the labile fraction was quantified using the Eyring and Arrhenius relations, respectively. By replacing in the latter equation the pressure-dependent parameters (E(a), k(ref)(T)()) by mathematical expressions, a global model was formulated. This mathematical model could accurately predict the inactivation rate constant of the labile fraction of orange PE as a function of pressure and temperature. In a second part, the stable fraction was studied in more detail. The stable fraction inactivated at temperatures exceeding 75 degrees C. Acidification (pH 3.7) enhanced thermal inactivation of the stable fraction, whereas addition of Ca(2+) ions (1 M) suppressed inactivation. At elevated pressure (up to 900 MPa), an antagonistic effect of pressure and temperature on the inactivation of the stable fraction was observed. The antagonistic effect was more pronounced in the presence of a 1 M CaCl(2) solution as compared to the inactivation in water, whereas it was less pronounced for the inactivation in acid medium.

  13. High pressure behaviour of TbN: an X-ray diffraction and computational study

    DEFF Research Database (Denmark)

    Jakobsen, J.M.; Madsen, G.K.H.; Jorgensen, J.E.

    2002-01-01

    In the present work, we report an X-ray powder diffraction study of TbN up to an applied hydrostatic pressure of 43 GPa. TbN was found to be stable in the 131 (NaCl structure) within the examined pressure interval, and the zero pressure bulk modulus was determined to be 176(7) GPa. The electronic...... to be itinerant and well described by standard DFT functionals. No pressure-induced phase transitions were found below 250 GPa with the LDA + U and GGA + U methods....

  14. High pressure behaviour of TbN: an X-ray diffraction and computational study

    DEFF Research Database (Denmark)

    Jakobsen, J.M.; Madsen, G.K.H.; Jorgensen, J.E.

    2002-01-01

    In the present work, we report an X-ray powder diffraction study of TbN up to an applied hydrostatic pressure of 43 GPa. TbN was found to be stable in the 131 (NaCl structure) within the examined pressure interval, and the zero pressure bulk modulus was determined to be 176(7) GPa. The electronic...... structure of ferromagnetic TbN has been studied using the linearized augmented plane-wave method. The calculated equilibrium volume and equation of state (EOS) for TbN agree poorly with experiment when the LDA and GGA versions of DFT were used. The agreement between the experimental and theoretical EOS...... is greatly improved by introducing an orbital dependent U term into the energy-functional. The 4f electrons in TbN-B1 are atomic like and highly correlated, and ferro-magnetic TbN-B1 is found to be a magnetic half-metal. Calculations find the spindown f-electrons in a hypothetical TbN-B2 (CsCl) structure...

  15. A study of mechanical sealing methods using graphite powder for high pressure vessel

    International Nuclear Information System (INIS)

    Jeong, H. Y.; Hong, J. T.; Ahn, S. H.; Joung, C. Y.

    2012-01-01

    The Fuel Test Loop (FTL) is a facility that can conduct fuel irradiation tests at the HANARO (High flux Advanced Neutron Application Reactor). The FTL simulates commercial NPP operating conditions such as pressure, temperature and neutron flux levels to conduct irradiation and thermo hydraulic tests. It is composed of an In Pile test Section (IPS) and an Out Pile System (OPS). The OPS contains a pressurizer, cooler, pump, heater and purification system, which are necessary to maintain the proper fluid conditions. In addition, the OPS contains engineered safety systems that can safely shutdown both HANARO and FTL if an accident occurs. The IPS accommodating fuel pins has a loaded IP 1 hole in HANARO, and a double pressure vessel for the design conditions of 350 .deg. C, 17.5MPa and is composed of an outer assembly and inner assembly. It has instruments such as a thermocouple, LVDT and SPND to measure the fuel performances during the test. FTL coolant is supplied to the IPS at the core of commercial nuclear power plants at the same temperature, pressure and flow conditions. Sensors are installed on the inside of the IPS to send signal transmission MI Cables to the outside for instrumentation through the pressure boundary. Therefore, the pressure boundary should be maintained in the sealing performance. Currently, the sealing of the IPS of the the FTL is maintained through a brazing method. However, A brazing method has disadvantages that can occur owing to thermal deformation or breakage in the instrumentation Mi cable. IPS inner assembly is a very long design length (approximately 5.29m), so it is difficult to perform in a vacuum chamber. Therefore, an easy and reliable way to assemble the instrumentation Mi cable mechanical sealing method has been studied. In this study, criteria tests at the pressure boundary were performed using universally applicable graphite powder for the instrumentation MI cable of various sizes

  16. Anomalous lattice compression and magnetic ordering in CuO at high pressures: A structural study and first-principles calculations

    Science.gov (United States)

    Kozlenko, D. P.; DruŻbicki, K.; Kichanov, S. E.; Lukin, E. V.; Liermann, H.-P.; Glazyrin, K. V.; Savenko, B. N.

    2017-02-01

    The structural and magnetic properties of multiferroic CuO have been studied by means of neutron and x-ray powder diffraction at pressures up to 11 and 38 GPa, respectively, and by first-principles theoretical calculations. Anomalous lattice compression is observed, with enlargement of the lattice parameter a , reaching a maximum at P = 13 GPa , followed by its reduction at higher pressures. The lattice distortion of the monoclinic structure at high pressures is accompanied by a progressive change of the oxygen coordination around Cu atoms from the square fourfold towards the octahedral sixfold coordination. The pressure-induced evolution of the structural properties and electronic structure of CuO was successfully elucidated in the framework of full-electronic density functional theory calculations with range-separated HSE06, and meta-generalized gradient approximation hybrid M06 functionals. The antiferromagnetic (AFM) ground state with a propagation vector q = (0.5 , 0 , -0.5 ) remains stable in the studied pressure range. From the obtained structural parameters, the pressure dependencies of the principal superexchange magnetic interactions were analyzed, and the pressure behavior of the Néel temperature as well as the magnetic transition temperature from the intermediate incommensurate AFM multiferroic state to the commensurate AFM ground state were evaluated. The estimated upper limit of the Néel temperature at P = 38 GPa is about 260 K, not supporting the previously predicted existence of the multiferroic phase at room temperature and high pressure.

  17. Study of Raman Spectroscopy on Phase Relations of CaCO3 at High Temperature and High Pressure

    Science.gov (United States)

    Li, M.; Zheng, H.; Duan, T.

    2006-05-01

    Laser Raman Spectroscopy was used to study phase relations between calcite I, calcite II and aragonite at high pressure and high temperature. The experiment was performed in an externally heated Basselt type diamond anvil cell (DAC). Natural calcite (calcite I) was used as starting mineral. The sample and a small chip of quartz were loaded in a cavity (300 μm in diameter and 250 μm in depth) in a rhenium gasket. The Na2CO3 aqueous solution of 1mol/L was also loaded as a pressure medium to yield hydrostatic pressure. The whole assembly was pressurized first and then heated stepwise to 400°C. Pressure and temperature in the chamber were determined by the shift of Raman band at 464 cm-1 of quartz and by NiCr-NiSi thermocouple, respectively. The Raman spectra were measured by a Renishaw 1000 spetrometer with 50 mW of 514.5nm argon-ion laser as the excitation light source. The slit width was 50 μm and the corresponding resolution was ±1 cm-1. From the experiments, we observed the phase transitions between calcite I and calcite II, calcite I and aragonite, calcite II and aragonite, respectively. Our data showed a negative slope for the boundary between calcite I and calcite II, which was similar to Bridgman's result, although Hess et al. gave a positive slope. The boundary with a negative slope for calcite II and aragonite was also defined, which had never been done before. And all these data can yield a more complete phase diagram of CaCO3 than the studies of Hess et al. and Suito et al.Reference:Bridgeman P. W.(1939) Journal: American Journal of Science, Vol. 237, p. 7-18Bassett W. A. et al. (1993) Journal: Review of Scientific Instruments, Vol. 64, p. 2340-2345Suito K. et al. (2001) Journal: American Mineralogist, Vol. 86, p. 997- 1002Hess N. J. et al. (1991) In A. K. Singh, Ed., Recent Trends in High Pressure Research; Proc. X IIIth AIRAPT International Conference on High Pressure Science and Technology, p. 236-241. Oxford & IBH Publishing Co. Pvt, Ltd., New

  18. Electrical Transport Experiments at High Pressure

    Energy Technology Data Exchange (ETDEWEB)

    Weir, S

    2009-02-11

    High-pressure electrical measurements have a long history of use in the study of materials under ultra-high pressures. In recent years, electrical transport experiments have played a key role in the study of many interesting high pressure phenomena including pressure-induced superconductivity, insulator-to-metal transitions, and quantum critical behavior. High-pressure electrical transport experiments also play an important function in geophysics and the study of the Earth's interior. Besides electrical conductivity measurements, electrical transport experiments also encompass techniques for the study of the optoelectronic and thermoelectric properties of materials under high pressures. In addition, electrical transport techniques, i.e., the ability to extend electrically conductive wires from outside instrumentation into the high pressure sample chamber have been utilized to perform other types of experiments as well, such as high-pressure magnetic susceptibility and de Haas-van Alphen Fermi surface experiments. Finally, electrical transport techniques have also been utilized for delivering significant amounts of electrical power to high pressure samples, for the purpose of performing high-pressure and -temperature experiments. Thus, not only do high-pressure electrical transport experiments provide much interesting and valuable data on the physical properties of materials extreme compression, but the underlying high-pressure electrical transport techniques can be used in a number of ways to develop additional diagnostic techniques and to advance high pressure capabilities.

  19. High-pressure powder neutron diffraction study on lead scandium niobate.

    Science.gov (United States)

    Maier, B J; Angel, R J; Mihailova, B; Marshall, W G; Gospodinov, M; Bismayer, U

    2011-01-26

    The structural evolution of PbSc(0.5)Nb(0.5)O(3) (PSN) under pressure has been studied by in situ powder neutron diffraction. Rietveld refinements to the data show that the continuous phase transition detected by x-ray diffraction at p(c) = 4.1 GPa (Maier et al 2010 Phys. Rev. B 81 174116) is associated with long-range ordering of antiphase octahedral tilts and local ordering of ferroic Pb displacements. Similar to PbSc(0.5)Ta(0.5)O(3) (PST) (Maier et al 2010 Acta Crystallogr. 66 280-91), antiphase octahedral tilting even exists below the critical pressure in a regime in which the structure retains a cubic metric. In contrast to PST, in which the Pb atomic displacement parameters (DPs) form ellipsoids elongated along the cubic {111} directions, the atomic DPs of Pb in PSN form flattened discs parallel to the cubic {111}-planes. This indicates that in PST the Pb displacements are along the cubic {111} directions, whereas in PSN the local Pb displacements are randomly distributed along the cubic {110} directions. The latter can be explained by the abundance of underbonded oxygen atoms associated with the chemical B-site disorder.

  20. Cage occupancies in the high pressure structure H methane hydrate: a neutron diffraction study.

    Science.gov (United States)

    Tulk, C A; Klug, D D; dos Santos, A M; Karotis, G; Guthrie, M; Molaison, J J; Pradhan, N

    2012-02-07

    A neutron diffraction study was performed on the CD(4) : D(2)O structure H clathrate hydrate to refine its CD(4) fractional cage occupancies. Samples of ice VII and hexagonal (sH) methane hydrate were produced in a Paris-Edinburgh press and in situ neutron diffraction data collected. The data were analyzed with the Rietveld method and yielded average cage occupancies of 3.1 CD(4) molecules in the large 20-hedron (5(12)6(8)) cages of the hydrate unit cell. Each of the pentagonal dodecahedron (5(12)) and 12-hedron (4(3)5(6)6(3)) cages in the sH unit cell are occupied with on average 0.89 and 0.90 CD(4) molecules, respectively. This experiment avoided the co-formation of Ice VI and sH hydrate, this mixture is more difficult to analyze due to the proclivity of ice VI to form highly textured crystals, and overlapping Bragg peaks of the two phases. These results provide essential information for the refinement of intermolecular potential parameters for the water-methane hydrophobic interaction in clathrate hydrates and related dense structures.

  1. GEM Operation in High-Pressure CF4: Studies of Charge and Scintillation Properties

    Science.gov (United States)

    da Luz, Hugo Natal; Conceicao, Ana Sofia; Veloso, JoÃo F. C. A.; dos Santos, Joaquim M. F.; Bento, AntÓnio C. S. S. M.; Mir, Jamil A.; Ferreira, LuÍs F. Requicha

    2009-06-01

    Tetrafluoromethane (CF4) combined with Helium-3 is widely used as the filling gas for neutron detectors. CF4 is generally known as an efficient gas for proton and tritium stopping, as well as a medium with low gamma sensitivity. Filling pressures above 2.5 bar are needed to achieve detector position resolutions below 1 mm. In this work, we have studied the performance of a single-GEM operating in CF4 in the pressure range of 1.0 to 2.5 bar and shown that it is possible to achieve gains one order of magnitude higher than what is needed for thermal neutron detection. Charge gains of 1.6 times 104 and 400 are reached at pressures of 1.0 and 2.5 bar, respectively, indicating good properties for this purpose. In opposition to gases with higher scintillation efficiency such as xenon, GEM scintillation readout with VUV-sensitive avalanche photodiodes results in gains that are less than one order of magnitude higher than those obtained with charge readout, delivering similar energy resolutions.

  2. High Pressure Study of Electrical Resistivity of CeB6 to 136 GPa

    Science.gov (United States)

    Forouzani, Neda; Lim, Jinhyuk; Schilling, James; Fabbris, Gilberto; Fisk, Zachary

    2014-03-01

    Since the 1960's the dense Kondo compound cerium hexaboride (CeB6) has attracted a great deal of interest. To investigate whether this material might evolve into a topological insulator under sufficient pressure, we have carried out four-point electrical resistivity measurements on CeB6 over the temperature range 1.3 K to 295 K in a diamond anvil cell to 136 GPa. Although a transition into an insulating phase is not observed, the evolution of the initial dense Kondo state under such extreme pressures is of considerable interest. As reported in earlier studies to 13 GPa, the temperature of the resistivity maximum near 3 K initially increases with pressure. We observe that between 33 and 53 GPa the resistivity maximum disappears and by 83 GPa CeB6 appears to have settled into a Fermi liquid state. The marked changes observed under pressure suggest that a change in valence and/or a structural transition may have occurred. Synchrotron x-ray diffraction measurements are being carried out to investigate possible changes in crystal structure under extreme pressures. Work at Washington Univ. supported by NSF DMR-1104742 and Carnegie/DOE/NNSA DE-FC52-08NA28554.

  3. High-pressure tritium

    International Nuclear Information System (INIS)

    Coffin, D.O.

    1976-01-01

    Some solutions to problems of compressing and containing tritium gas to 200 MPa at 700 0 K are discussed. The principal emphasis is on commercial compressors and high-pressure equipment that can be easily modified by the researcher for safe use with tritium. Experience with metal bellows and diaphragm compressors has been favorable. Selection of materials, fittings, and gauges for high-pressure tritium work is also reviewed briefly

  4. Study of emission of a volume nanosecond discharge plasma in xenon, krypton and argon at high pressures

    International Nuclear Information System (INIS)

    Baksht, E Kh; Lomaev, Mikhail I; Rybka, D V; Tarasenko, Viktor F

    2006-01-01

    The emission properties of a volume nanosecond discharge plasma produced in xenon, krypton and argon at high pressures in a discharge gap with a cathode having a small radius of curvature are studied. Spectra in the range 120-850 nm and amplitude-time characteristics of xenon emission at different regimes and excitation techniques are recorded and analysed. It is shown that upon excitation of the volume discharge initiated by a beam of avalanche electrons, at least 90% of the energy in the spectral range 120-850 nm is emitted by xenon dimers. For xenon at a pressure of 1.2 atm, ∼45 mJ of the spontaneous emission energy was obtained in the full solid angle in a pulse with the full width at half-maximum ∼130 ns. (laser applications and other topics in quantum electronics)

  5. Magnetic EXAFS study of Fe-Ni invar alloy under high pressure using nano-polycrystalline diamond anvils

    Science.gov (United States)

    Matsumoto, Ken; Maruyama, Hiroshi; Ishimatsu, Naoki; Kawamura, Naomi; Mizumaki, Masaichiro; Irifune, Tetsuo; Sumiya, Hitoshi

    2012-07-01

    The magnetic EXAFS technique was applied to study the local magnetic structure in Fe-Ni Invar alloy under high pressures. Nano-polycrystalline diamond was used to apply pressure in a diamond anvil cell. As a result, we succeeded in recording a glitch-free spectrum with a high accuracy by preventing Bragg diffraction from the diamonds. As the pressure was increased, the ferromagnetic correlation was strongly reduced, which was more remarkable for Fe atoms than for Ni atoms. The canting effect of the magnetic moment may be crucial for a rapid decrease in the ferromagnetic correlation. This local magnetic structure in the Invar alloy is consistent with a model based on the non-collinear spin structure.

  6. High Pressure Scanning Tunneling Microscopy Studies of Adsorbate Structure and Mobility during Catalytic Reactions. Novel Design of an Ultra High Pressure, High Temperature Scanning Tunneling Microscope System for Probing Catalytic Conversions

    International Nuclear Information System (INIS)

    Tang, David Chi-Wai

    2005-01-01

    The aim of the work presented therein is to take advantage of scanning tunneling microscope's (STM) capability for operation under a variety of environments under real time and at atomic resolution to monitor adsorbate structures and mobility under high pressures, as well as to design a new generation of STM systems that allow imaging in situ at both higher pressures (35 atm) and temperatures (350 C). The design of a high pressure, high temperature scanning tunneling microscope system, that is capable of monitoring reactions in situ at conditions from UHV and ambient temperature up to 1 atm and 250 C, is briefly presented along with vibrational and thermal analysis, as this system serves as a template to improve upon during the design of the new ultra high pressure, high temperature STM. Using this existing high pressure scanning tunneling microscope we monitored the co-adsorption of hydrogen, ethylene and carbon dioxide on platinum (111) and rhodium (111) crystal faces in the mTorr pressure range at 300 K in equilibrium with the gas phase. During the catalytic hydrogenation of ethylene to ethane in the absence of CO the metal surfaces are covered by an adsorbate layer that is very mobile on the time scale of STM imaging. We found that the addition of CO poisons the hydrogenation reaction and induces ordered structures on the single crystal surfaces. Several ordered structures were observed upon CO addition to the surfaces pre-covered with hydrogen and ethylene: a rotated (√19 x √19)R23.4 o on Pt(111), and domains of c(4 x 2)-CO+C 2 H 3 , previously unobserved (4 x 2)-CO+3C 2 H 3 , and (2 x 2)-3CO on Rh(111). A mechanism for CO poisoning of ethylene hydrogenation on the metal single crystals was proposed, in which CO blocks surface metal sites and reduces adsorbate mobility to limit adsorption and reaction rate of ethylene and hydrogen. In order to observe heterogeneous catalytic reactions that occur well above ambient pressure and temperature that more closely

  7. Experimental Study on Hydrate Induction Time of Gas-Saturated Water-in-Oil Emulsion using a High-Pressure Flow Loop

    Directory of Open Access Journals (Sweden)

    Lv X.F.

    2015-11-01

    Full Text Available Hydrate is one of the critical precipitates which have to be controlled for subsea flow assurance. The induction time of hydrate is therefore a significant parameter. However, there have been few studies on the induction time of the natural gas hydrate formation in a flow loop system. Consequently, a series of experiments were firstly performed, including water, natural gas and Diesel oil, on the hydrate induction time under various conditions such as the supercooling and supersaturation degree, water cut, anti-agglomerant dosage, etc. The experiments were conducted in a high-pressure hydrate flow loop newly constructed in the China University of Petroleum (Beijing, and dedicated to flow assurance studies. Then, based on previous research, this study puts forward a method for induction time, which is characterized by clear definition, convenient measurement and good generality. Furthermore, we investigated the influences of the experimental parameters and analyzed the experimental phenomena for the hydrate induction time in a flowing system.

  8. Surface Interactions and Confinement of Methane: A High Pressure Magic Angle Spinning NMR and Computational Chemistry Study

    Energy Technology Data Exchange (ETDEWEB)

    Ok, Salim; Hoyt, David W.; Andersen, Amity; Sheets, Julie; Welch, Susan A.; Cole, David R.; Mueller, Karl T.; Washton, Nancy M.

    2017-01-18

    Characterization and modeling of the molecular-level behavior of simple hydrocarbon gases, such as methane, in the presence of both nonporous and nano-porous mineral matrices allows for predictive understanding of important processes in engineered and natural systems. In this study, changes in local electromagnetic environments of the carbon atoms in methane under conditions of high pressure (up to 130 bar) and moderate temperature (up to 346 K) were observed with 13C magic-angle spinning (MAS) NMR spectroscopy while the methane gas was mixed with two model solid substrates: a fumed non-porous, 12 nm particle size silica and a mesoporous silica with 200 nm particle size and 4 nm average pore diameter. Examination of the interactions between methane and the silica systems over temperatures and pressures that include the supercritical regime was allowed by a novel high pressure MAS sample containment system, which provided high resolution spectra collected under in situ conditions. For pure methane, no significant thermal effects were found for the observed 13C chemical shifts at all pressures studied here (28.2 bar, 32.6 bar, 56.4 bar, 65.1 bar, 112.7 bar, and 130.3 bar). However, the 13C chemical shifts of resonances arising from confined methane changed slightly with changes in temperature in mixtures with mesoporous silica. The chemical shift values of 13C nuclides in methane change measurably as a function of pressure both in the pure state and in mixtures with both silica matrices, with a more pronounced shift when meso-porous silica is present. Molecular-level simulations utilizing GCMC, MD and DFT confirm qualitatively that the experimentally measured changes are attributed to interactions of methane with the hydroxylated silica surfaces as well as densification of methane within nanopores and on pore surfaces.

  9. Surface Interactions and Confinement of Methane: A High Pressure Magic Angle Spinning NMR and Computational Chemistry Study

    International Nuclear Information System (INIS)

    Ok, Salim; Hoyt, David W.; Andersen, Amity; Sheets, Julie; Welch, Susan A.

    2017-01-01

    Characterization and modeling of the molecular-level behavior of simple hydrocarbon gases, such as methane, in the presence of both nonporous and nanoporous mineral matrices allows for predictive understanding of important processes in engineered and natural systems. In this study, we observed changes in local electromagnetic environments of the carbon atoms in methane under conditions of high pressure (up to 130 bar) and moderate temperature (up to 346 K) with 13 C magic-angle spinning (MAS) NMR spectroscopy while the methane gas was mixed with two model solid substrates: a fumed nonporous, 12 nm particle size silica and a mesoporous silica with 200 nm particle size and 4 nm average pore diameter. Examination of the interactions between methane and the silica systems over temperatures and pressures that include the supercritical regime was allowed by a novel high pressure MAS sample containment system, which provided high resolution spectra collected under in situ conditions. There was no significant thermal effects were found for the observed 13 C chemical shifts at all pressures studied here (28.2, 32.6, 56.4, 65.1, 112.7, and 130.3 bar) for pure methane. However, the 13 C chemical shifts of resonances arising from confined methane changed slightly with changes in temperature in mixtures with mesoporous silica. The chemical shift values of 13 C nuclides in methane change measurably as a function of pressure both in the pure state and in mixtures with both silica matrices, with a more pronounced shift when meso-porous silica is present. Molecular-level simulations utilizing GCMC, MD, and DFT confirm qualitatively that the experimentally measured changes are attributed to interactions of methane with the hydroxylated silica surfaces as well as densification of methane within nanopores and on pore surfaces.

  10. Field and petrological study of metasomatism and high-pressure carbonation from lawsonite eclogite-facies terrains, Alpine Corsica

    Science.gov (United States)

    Piccoli, Francesca; Vitale Brovarone, Alberto; Ague, Jay J.

    2018-04-01

    This study presents new field and petrological data on carbonated metasomatic rocks from the lawsonite-eclogite units of Alpine Corsica. These rocks form along major, slab-scale lithological boundaries of the subducted Alpine Tethys plate. Our results indicate that a large variety of rocks ranging from metamafic/ultramafic to metafelsic can react with carbon-bearing fluids, leading to carbon sequestration at high-pressure conditions. The process of carbonation includes both replacement of silicates by high-pressure carbonate, and carbonate veining. The field, microstructural and mineralogical data strongly suggest that the metasomatism was mediated by the infiltration of external fluids of mixed origin, including both mafic/ultramafic and metasedimentary sources. Our results support the following three-step evolution: (i) Release of aqueous fluids by lawsonite and/or antigorite breakdown at depth; (ii) Fluid channelization along the base of the metasedimentary pile of the subducted lithospheric plate and related reactive fluid flow leading to carbonate mineral dissolution; (iii) Further interactions of the resulting carbon-bearing fluids with slab-forming rocks at depths of ca. 70 km and carbonation of pre-existing silicate-rich lithologies. This study highlights the importance of carbonate-bearing fluids evolving along down-T, down-P paths, such as along slab-parallel lithological boundaries, for the sequestration of carbon in subduction zones, and suggests that similar processes may also operate in collisional settings. Fig. S2: Petrogenetic grid in the CaFMASH+CO2 system for the antigorite and clinopyroxene carbonation reactions, together with grossular forming reaction during decarbonation. Reactions are written with the high T assemblage to the right of the = sign.

  11. High-pressure microfluidics

    Science.gov (United States)

    Hjort, K.

    2015-03-01

    When using appropriate materials and microfabrication techniques, with the small dimensions the mechanical stability of microstructured devices allows for processes at high pressures without loss in safety. The largest area of applications has been demonstrated in green chemistry and bioprocesses, where extraction, synthesis and analyses often excel at high densities and high temperatures. This is accessible through high pressures. Capillary chemistry has been used since long but, just like in low-pressure applications, there are several potential advantages in using microfluidic platforms, e.g., planar isothermal set-ups, large local variations in geometries, dense form factors, small dead volumes and precisely positioned microstructures for control of reactions, catalysis, mixing and separation. Other potential applications are in, e.g., microhydraulics, exploration, gas driven vehicles, and high-pressure science. From a review of the state-of-art and frontiers of high pressure microfluidics, the focus will be on different solutions demonstrated for microfluidic handling at high pressures and challenges that remain.

  12. A structural study of the pseudo-binary mercury chalcogenide alloy HgSe sub 0 sub . sub 7 S sub 0 sub . sub 3 at high pressure

    CERN Document Server

    Kozlenko, D P; Hull, S; Knorr, K; Savenko, B N; Shchennikov, V V; Voronin, V I

    2002-01-01

    The structure of the pseudo-binary mercury chalcogenide alloy HgSe sub 0 sub . sub 7 S sub 0 sub . sub 3 has been studied by means of X-ray and neutron powder diffraction at pressure up to 8.5 GPa. A phase transition from the cubic zinc blende structure to the hexagonal cinnabar structure was observed at P approx 1 GPa. The obtained structural parameters were used for the analysis of the geometrical relationship between the zinc blende and the cinnabar phases. The zinc blende-cinnabar phase transition is discussed in the framework of the Landau theory of phase transitions. It was found that the possible order parameter for the structural transformation is the spontaneous strain e sub 4. This assignment agrees with previously observed high pressure behaviour of the elastic constants of other mercury chalcogenides

  13. A Structural Study of the Pseudo-Binary Mercury Chalcogenide Alloy HgSe_{0.7}S_{0.3} at High Pressure

    CERN Document Server

    Kozlenko, D P; Ehm, L; Knorr, K; Hull, S; Shchennikov, V V; Voronin, V I

    2002-01-01

    The structure of the pseudo-binary mercury chalcogenide alloy HgSe_{0.7}S_{0.3} has been studied by means of X-ray and neutron powder diffraction at pressure up to 8.5 GPa. A phase transition from the cubic zinc blende structure to the hexagonal cinnabar structure was observed at P{\\sim}1 GPa. The obtained structural parameters were used for the analysis of the geometrical relationship between the zinc blende and the cinnabar phases. The zinc blende-cinnabar phase transition is discussed in the framework of Landau theory of the phase transitions. It was found that the possible order parameter for the structural transformation is the spontaneous strain e_{4}. This assignment agrees with previously observed high pressure behaviour of the elastic constants of other mercury chalcogenides.

  14. High-pressure apparatus

    OpenAIRE

    Schepdael, van, L.J.M.; Bartels, P.V.; Berg, van den, R.W.

    1999-01-01

    The invention relates to a high-pressure device (1) having a cylindrical high-pressure vessel (3) and prestressing means in order to exert an axial pressure on the vessel. The vessel (3) can have been formed from a number of layers of composite material, such as glass, carbon or aramide fibers which are oriented in the peripheral direction and are embedded in a matrix of epoxy resin or polyurethane. By applying the axial prestress to the pressure vessel (3), the tangential stress is distribut...

  15. Phase transitions in solids under high pressure

    CERN Document Server

    Blank, Vladimir Davydovich

    2013-01-01

    Phase equilibria and kinetics of phase transformations under high pressureEquipment and methods for the study of phase transformations in solids at high pressuresPhase transformations of carbon and boron nitride at high pressure and deformation under pressurePhase transitions in Si and Ge at high pressure and deformation under pressurePolymorphic α-ω transformation in titanium, zirconium and zirconium-titanium alloys Phase transformations in iron and its alloys at high pressure Phase transformations in gallium and ceriumOn the possible polymorphic transformations in transition metals under pressurePressure-induced polymorphic transformations in АIBVII compoundsPhase transformations in AIIBVI and AIIIBV semiconductor compoundsEffect of pressure on the kinetics of phase transformations in iron alloysTransformations during deformation at high pressure Effects due to phase transformations at high pressureKinetics and hysteresis in high-temperature polymorphic transformations under pressureHysteresis and kineti...

  16. The Use of High Pressure Freezing and Freeze Substitution to Study Host-Pathogen Interactions in Fungal Diseases of Plants

    Science.gov (United States)

    Mims, C. W.; Celio, Gail J.; Richardson, Elizabeth A.

    2003-12-01

    This article reports on the use of high pressure freezing followed by freeze substitution (HPF/FS) to study ultrastructural details of host pathogen interactions in fungal diseases of plants. The specific host pathogen systems discussed here include a powdery mildew infection of poinsettia and rust infections of daylily and Indian strawberry. The three pathogens considered here all attack the leaves of their hosts and produce specialized hyphal branches known as haustoria that invade individual host cells without killing them. We found that HPF/FS provided excellent preservation of both haustoria and host cells for all three host pathogen systems. Preservation of fungal and host cell membranes was particularly good and greatly facilitated the detailed study of host pathogen interfaces. In some instances, HPF/FS provided information that was not available in samples prepared for study using conventional chemical fixation. On the other hand, we did encounter various problems associated with the use of HPF/FS. Examples included freeze damage of samples, inconsistency of fixation in different samples, separation of plant cell cytoplasm from cell walls, breakage of cell walls and membranes, and splitting of thin sections. However, we believe that the outstanding preservation of ultrastructural details afforded by HPF/FS significantly outweighs these problems and we highly recommend the use of this fixation protocol for future studies of fungal host-plant interactions.

  17. Fascination at high pressures

    International Nuclear Information System (INIS)

    Chidambaram, R.

    1992-01-01

    Research at high pressures has developed into an interdisciplinary area which has important implications for and applications in the areas of physics, chemistry, materials sciences, planetary sciences, biology, engineering sciences and technology. The state of-the-art in this field is reviewed and future directions are indicated. (M.G.B.)

  18. Volume and structural study of Fe64Mn36 anti-ferromagnetic Invar alloy under high pressure

    Science.gov (United States)

    Matsushita, M.; Nakano, S.; Ohfuji, H.; Yamada, I.; Kikegawa, T.

    2011-03-01

    We have investigated the pressure variation of the volume and structure of an FCC Fe64Mn36 anti-ferromagnetic Invar alloy. The inclination of the pressure-volume (P-V) curve of the FCC structure becomes discontinuous at a pressure of 4 GPa. According to the bulk modulus at zero pressure estimated by the Birch-Murnaghan equation of state, the pressure between 4 and 10 GPa is 33 GPa larger than that at a pressure below 4 GPa. Considering previous experiments on magnetism at high pressure the Neel temperature at 4 GPa almost decreases to room temperature. These results suggest that the increase in the bulk modulus by 33 GPa can be attributed to the pressure-induced magnetic phase transition from anti-ferromagnetism to paramagnetism. Volume at zero pressure was estimated using the Birch-Murnaghan equation of state. The volume of FCC structure in the anti-ferromagnetic state was 1.17% larger than the volume in the paramagnetic state, namely, the spontaneous magnetostriction was 1.17%. Pressure-induced structural transition from FCC to HCP occurs with an increase in the pressure, especially at up to 5 GPa. The value of c/a is 1.62; this value almost corresponds to that of an ideal HCP structure. The bulk modulus of the HCP structure estimated by the Birch-Murnaghan equation of state is larger than that of the FCC structure, and the volume/atom ratio is smaller than that of the FCC structure.

  19. Vitreous Anorthite (CaAl2Si2O8) at High Pressure: A First-Principles Molecular Dynamics Study

    Science.gov (United States)

    Ghosh, D. B.; Karki, B. B.

    2017-12-01

    structural details suggest that the pressure response of the cold compressed glasses are not only inherently different in the 0 - 10 GPa interval, the density and the average coordination are consistently lower than the hot compressed glasses. Hot-compressed glasses may therefore be the better analog in the study of high-pressure silicate melts.

  20. A high pressure neutron study of colossal magnetoresistant NdMnAsO(0.95)F(0.05).

    Science.gov (United States)

    Wildman, E J; Tucker, M G; Mclaughlin, A C

    2015-03-25

    A high pressure neutron diffraction study of the oxypnictide NdMnAsO0.95F0.05 has been performed at temperatures of 290-383 K and pressures up to 8.59 GPa. The results demonstrate that the antiferromagnetic order of the Mn spins is robust to pressures of up to 8.59 GPa. TN is enhanced from 360 to 383 K upon applying an external pressure of 4.97 GPa, a rate of 4.63 K GPa(-1). NdMnAsO0.95F0.05 is shown to violate Bloch's rule which would suggest that NdMnAsO0.95F0.05 is on the verge of a localized to itinerant transition. There is no evidence of a structural transition but applied pressure tends to result in more regular As-Mn-As and Nd-O-Nd tetrahedra. The unit cell is significantly more compressible along the c-axis than the a-axis, as the interlayer coupling is weaker than the intrinsic bonds contained within NdO and MnAs slabs.

  1. A molecular dynamics study of ambient and high pressure phases of silica: structure and enthalpy variation with molar volume.

    Science.gov (United States)

    Rajappa, Chitra; Sringeri, S Bhuvaneshwari; Subramanian, Yashonath; Gopalakrishnan, J

    2014-06-28

    Extensive molecular dynamics studies of 13 different silica polymorphs are reported in the isothermal-isobaric ensemble with the Parrinello-Rahman variable shape simulation cell. The van Beest-Kramer-van Santen (BKS) potential is shown to predict lattice parameters for most phases within 2%-3% accuracy, as well as the relative stabilities of different polymorphs in agreement with experiment. Enthalpies of high-density polymorphs - CaCl2-type, α-PbO2-type, and pyrite-type - for which no experimental data are available as yet, are predicted here. Further, the calculated enthalpies exhibit two distinct regimes as a function of molar volume-for low and medium-density polymorphs, it is almost independent of volume, while for high-pressure phases a steep dependence is seen. A detailed analysis indicates that the increased short-range contributions to enthalpy in the high-density phases arise not only from an increased coordination number of silicon but also shorter Si-O bond lengths. Our results indicate that amorphous phases of silica exhibit better optimization of short-range interactions than crystalline phases at the same density while the magnitude of Coulombic contributions is lower in the amorphous phase.

  2. High pressure stability analysis and chemical bonding of Ti1-xZrxN alloy: A first principle study

    International Nuclear Information System (INIS)

    Chauhan, Mamta; Gupta, Dinesh C.

    2016-01-01

    First-principles pseudo-potential calculations have been performed to analyze the stability of Ti 1-x Zr x N alloy under high pressures. The first order phase transition from B1 to B2 phase has been observed in this alloy at high pressure. The variation of lattice parameter with the change in concentration of Zr atom in Ti 1-x Zr x N is also reported in both the phases. The calculations for density of states have been performed to understand the alloying effects on chemical bonding of Ti-Zr-N alloy.

  3. High Pressure Scanning Tunneling Microscopy and High PressureX-ray Photoemission Spectroscopy Studies of Adsorbate Structure,Composition and Mobility during Catalytic Reactions on A Model SingleCrystal

    Energy Technology Data Exchange (ETDEWEB)

    Montano, Max O. [Univ. of California, Berkeley, CA (United States)

    2006-01-01

    Our research focuses on taking advantage of the ability of scanning tunneling microscopy (STM) to operate at high-temperatures and high-pressures while still providing real-time atomic resolution images. We also utilize high-pressure x-ray photoelectron spectroscopy (HPXPS) to monitor systems under identical conditions thus giving us chemical information to compare and contrast with the structural and dynamic data provided by STM.

  4. High pressure phase transformations revisited

    Science.gov (United States)

    Levitas, Valery I.

    2018-04-01

    High pressure phase transformations play an important role in the search for new materials and material synthesis, as well as in geophysics. However, they are poorly characterized, and phase transformation pressure and pressure hysteresis vary drastically in experiments of different researchers, with different pressure transmitting media, and with different material suppliers. Here we review the current state, challenges in studying phase transformations under high pressure, and the possible ways in overcoming the challenges. This field is critically compared with fields of phase transformations under normal pressure in steels and shape memory alloys, as well as plastic deformation of materials. The main reason for the above mentioned discrepancy is the lack of understanding that there is a fundamental difference between pressure-induced transformations under hydrostatic conditions, stress-induced transformations under nonhydrostatic conditions below yield, and strain-induced transformations during plastic flow. Each of these types of transformations has different mechanisms and requires a completely different thermodynamic and kinetic description and experimental characterization. In comparison with other fields the following challenges are indicated for high pressure phase transformation: (a) initial and evolving microstructure is not included in characterization of transformations; (b) continuum theory is poorly developed; (c) heterogeneous stress and strain fields in experiments are not determined, which leads to confusing material transformational properties with a system behavior. Some ways to advance the field of high pressure phase transformations are suggested. The key points are: (a) to take into account plastic deformations and microstructure evolution during transformations; (b) to formulate phase transformation criteria and kinetic equations in terms of stress and plastic strain tensors (instead of pressure alone); (c) to develop multiscale continuum

  5. A neutron diffraction study of the structure of heavy water at pressure using a new high-pressure cell

    International Nuclear Information System (INIS)

    Neilson, G.W.; Page, D.I.; Howell, W.S.

    1979-01-01

    Neutron diffraction measurements have been made at pressures up to 1 kbar on heavy water contained in a high-pressure cell manufactured from titanium zirconium alloy. The results have been used to test the degree to which the microscopic structure is susceptible to isothermal compression. The likely future progress in this field is commented on. (author)

  6. Pneumatic Performance Study of a High Pressure Ejection Device Based on Real Specific Energy and Specific Enthalpy

    Directory of Open Access Journals (Sweden)

    Jie Ren

    2014-09-01

    Full Text Available In high-pressure dynamic thermodynamic processes, the pressure is much higher than the air critical pressure, and the temperature can deviate significantly from the Boyle temperature. In such situations, the thermo-physical properties and pneumatic performance can’t be described accurately by the ideal gas law. This paper proposes an approach to evaluate the pneumatic performance of a high-pressure air catapult launch system, in which esidual functions are used to compensate the thermal physical property uncertainties of caused by real gas effects. Compared with the Nelson-Obert generalized compressibility charts, the precision of the improved virial equation of state is better than Soave-Redlich-Kwong (S-R-K and Peng-Robinson (P-R equations for high pressure air. In this paper, the improved virial equation of state is further used to establish a compressibility factor database which is applied to evaluate real gas effects. The specific residual thermodynamic energy and specific residual enthalpy of the high-pressure air are also derived using the modified corresponding state equation and improved virial equation of state which are truncated to the third virial coefficient. The pneumatic equations are established on the basis of the derived residual functions. The comparison of the numerical results shows that the real gas effects are strong, and the pneumatic performance analysis indicates that the real dynamic thermodynamic process is obviously different from the ideal one.

  7. A high pressure cell for supercritical CO2 on-line chemical reactions studied with x-ray techniques

    NARCIS (Netherlands)

    Hermida-Merino, Daniel; Portale, Giuseppe; Fields, Peter; Wilson, Richard; Bassett, Simon P.; Jennings, James; Dellar, Martin; Gommes, Cedric; Howdle, Steven M.; Vrolijk, Benno C. M.; Bras, Wim

    A versatile high pressure X-ray sample cell has been developed for conducting in situ time-resolved X-ray scattering experiments in the pressure and temperature regime required (pressures up to 210 bars and temperatures up to 120 degrees C) for chemical reactions in supercritical fluids. The large

  8. Helimagnetism of Fe: High pressure study of an Y.sub.2./sub.Fe.sub.17./sub. single crystal

    Czech Academy of Sciences Publication Activity Database

    Prokhnenko, Olexandr; Kamarád, Jiří; Prokeš, K.; Arnold, Zdeněk; Andreev, Alexander V.

    2005-01-01

    Roč. 94, - (2005), 107201/1-107201/4 ISSN 0031-9007 R&D Projects: GA ČR(CZ) GP202/04/P014 Institutional research plan: CEZ:AV0Z10100521 Keywords : high pressures * iron * magnetic structures * neutron diffraction * helimagnetic structure Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 7.489, year: 2005

  9. Experimental study of the zirconium alloy oxidation under high pressure of steam and modelling of the mechanisms

    International Nuclear Information System (INIS)

    Dali, Yacoub

    2007-01-01

    The corrosion of the cladding materials used for the fuel rods is one of the limiting factor of their lifetime in light water reactors. In this field, the aim of the nuclear industry is today to increase the time and the number of cycles and to submit the claddings in zirconium alloys to higher corrosive conditions. In this way, new alloys devoted to replace the standard Zircaloy-4, for instance Nb containing alloys, have been recently developed and licensed and show better corrosion resistance. A better understanding of the corrosion mechanisms of the zirconium alloys is necessary to predict the corrosion behaviour of these materials. In this work, the oxidation rate of model alloys of two metallurgic families has been studied in steam in a pressure range between 100 milli-bars and 100 bars. The Zircaloy type alloys contain as alloying elements oxygen and/or tin and/or iron and chromium. For the Zr-Nb family, three niobium contents have been studied, respectively 0.2, 0.4 and 1 weight percent of niobium. Our objectives were to understand the variations of the reactivity between the low pressure and the high pressure range, in quantifying the dependency of the corrosion rate with the steam pressure and the alloying element concentrations. The segregation process of the niobium at the surface has also been studied on the Zr-Nb alloys. During this work, a magnetic suspension thermo-balance has been developed and used to follow in-situ the corrosion rate at high pressure of water vapour. The oxide layers have been characterized by many techniques, macro and micro-photo-electrochemistry, XRD, FEG-SEM, XPS, HR-TEM and SIMS. For the Zircaloy type alloys, we have confirmed the major role of the intermetallic precipitates Zr(Fe,Cr) 2 on the corrosion resistance. Unlike the standard Zircaloy-4, for which the oxidation rate does not depend on the pressure of the water vapour and is thus limited by the vacancy diffusion in the oxide layer, we have shown that the rate of the

  10. High pressure study of water-salt systems, phase equilibria, partitioning, thermodynic properties and implication for large icy worlds hydrospheres.

    Science.gov (United States)

    Journaux, B.; Brown, J. M.; Abramson, E.; Petitgirard, S.; Pakhomova, A.; Boffa Ballaran, T.; Collings, I.

    2017-12-01

    Water salt systems are predicted to be present in deep hydrosphere inside water-rich planetary bodies, following water/rock chemical interaction during early differentiation stages or later hydrothermal activity. Unfortunately the current knowledge of the thermodynamic and physical properties of aqueous salt mixtures at high pressure and high temperature is still insufficient to allow realistic modeling of the chemical or dynamic of thick planetary hydrospheres. Recent experimental results have shown that the presence of solutes, and more particularly salts, in equilibrium with high pressure ices have large effects on the stability fields, buoyancy and chemistry of all the phases present at these extreme conditions. Effects currently being investigated by our research group also covers ice melting curve depressions that depend on the salt species and incorporation of solutes inside the crystallographic lattice of high pressure ices. Both of these could have very important implication at the planetary scale, enabling thicker/deeper liquid oceans, and allowing chemical transportation through the high pressure ice layer in large icy worlds. We will present the latest results obtained in-situ using diamond anvil cell, coupled with Synchrotron X-Ray diffraction, Raman Spectroscopy and optical observations, allowing to probe the crystallographic structure, equations of state, partitioning and phase boundary of high pressure ice VI and VII in equilibrium with Na-Mg-SO4-Cl ionic species at high pressures (1-10 GPa). The difference in melting behavior depending on the dissolved salt species was characterized, suggesting differences in ionic speciation at liquidus conditions. The solidus P-T conditions were also measured as well as an increase of lattice volumes interpreted as an outcome of ionic incorporation in HP ice during incongruent crystallization. The measured phase diagrams, lattice volumes and important salt incorporations suggest a more complex picture of the

  11. High-pressure single-crystal neutron scattering study of magnetic and Fe vacancy orders in (Tl,Rb)2Fe4Se5 superconductor

    OpenAIRE

    Ye, Feng; Bao, Wei; Chi, Songxue; Santos, Antonio M. dos; Molaison, Jamie J.; Fang, Minghu; Wang, Hangdong; Wang, Qianhui Mao Jinchen; Liu, Juanjuan; Sheng, Jieming

    2014-01-01

    The magnetic and iron vacancy orders in superconducting (Tl,Rb)2Fe4Se5 single-crystals are investigated by using a high-pressure neutron diffraction technique. Similar to the temperature effect, the block antiferromagnetic order gradually decreases upon increasing pressure while the Fe vacancy superstructural order remains intact before its precipitous disappearance at the critical pressure Pc = 8.3 GPa. Combined with previously determined Pc for superconductivity, our phase diagram under pre...

  12. High-Pressure Polymorphism in Orthoamphiboles

    Science.gov (United States)

    Finkelstein, G. J.; Zhang, D.; Shelton, H.; Dera, P.

    2017-12-01

    Amphiboles are double-chain silicate minerals that are the structurally hydrated counterpart to single-chain, anhydrous pyroxenes. They may play an important role in the earth as a carrier for volatiles in subduction zones, as well as a generator for seismic anisotropy in the upper mantle. Recent work has described previously unrecognized high-pressure polymorphism at low temperatures in a variety of pyroxene minerals, which may be relevant for the structure and dynamics of thick, cold, subducted slabs. However, high-pressure polymorphism in amphiboles above a few GPa in pressure has not been well explored, and if similar polymorphism to pyroxenes exists in this mineral family, it may affect the extent and depth of volatile transport in amphiboles, as well as their rheological properties. At low temperatures and high pressures, orthopyroxenes undergo crystal structure transitions at lower pressures than clinopyroxenes (10-30 GPa vs. > 50 GPa), so for this study we have investigated polymorphism in the anthophyllite-gedrite (Al-free and Al rich) orthoamphibole solid solution series. Using neon gas-loaded diamond anvil cells, we compressed both phases to a maximum pressure of 31 GPa, and observed transitions to new monoclinic structures in both endmembers. In this presentation, we will discuss the details of these transitions and implications for the earth's interior.

  13. High-pressure structural behavior of the double perovskite Sr2CrReO6: an experimental and theoretical study

    DEFF Research Database (Denmark)

    Olsen, J.S.; Gerward, Leif; Vaitheeswaran, G.

    2009-01-01

    The high-pressure structural behavior of Sr2CrReO6 has been studied experimentally using synchrotron radiation and the diamond anvil cell and theoretically using density functional theory. The experimental zero-pressure bulk modulus is B0=1704GPa and the pressure derivative is B0'=4.71.0. These r......'=4.71.0. These results compare well with the calculated values 172.6GPa and 5.7. A pseudo-cubic unit cell can describe the crystal structure at low pressure, but the tetragonal structure becomes evident at high pressure....

  14. A study on environmental pollution caused by radioactive substances and its countermeasure techniques. Part 3. Development on decontamination techniques with high pressure cleaning method

    International Nuclear Information System (INIS)

    Narita, Yasunori; Nozaki, Atsuo; Kakuma, Takayuki; Shinohara, Naohide; Yoshino, Hiroshi

    2012-01-01

    A huge area of Fukushima was contaminated by the radiation released from the nuclear disaster. As a result, decontamination has become an urgent task in densely populated area and developments of an effective decontamination method are desired. So, we carried out the plan of the decontamination methods with a high pressure cleaner in present study. Surface with covered with concrete materials at horizontal plane was washed with high pressure cleaner, consequently, radioactivity was approximately 80% decreased. Further, the wash act with brushing are raised efficiency by 10%. So, the case of washing with surfactant shows no increase efficiency. (author)

  15. A study of energy-size relationship and wear rate in a lab-scale high pressure grinding rolls unit

    Science.gov (United States)

    Rashidi Dashtbayaz, Samira

    This study is focused on two independent topics of energy-size relationship and wear-rate measurements on a lab-scale high pressure grinding rolls (HPGR). The first part of this study has been aimed to investigate the influence of the operating parameters and the feed characteristics on the particle-bed breakage using four different ore samples in a 200 mm x 100 mm lab-scale HPGR. Additionally, multistage grinding, scale-up from a lab-scale HPGR, and prediction of the particle size distributions have been studied in detail. The results obtained from energy-size relationship studies help with better understanding of the factors contributing to more energy-efficient grinding. It will be shown that the energy efficiency of the two configurations of locked-cycle and open multipass is completely dependent on the ore properties. A test procedure to produce the scale-up data is presented. The comparison of the scale-up factors between the data obtained on the University of Utah lab-scale HPGR and the industrial machine at the Newmont Boddington plant confirmed the applicability of lab-scale machines for trade-off studies. The population balance model for the simulation of product size distributions has shown to work well with the breakage function estimated through tests performed on the HPGR at high rotational speed. Selection function has been estimated by back calculation of population balance model with the help of the experimental data. This is considered to be a major step towards advancing current research on the simulation of particle size distribution by using the HPGR machine for determining the breakage function. Developing a technique/setup to measure the wear rate of the HPGR rolls' surface is the objective of the second topic of this dissertation. A mockup was initially designed to assess the application of the linear displacement sensors for measuring the rolls' weight loss. Upon the analysis of that technique and considering the corresponding sources of

  16. Superconductivity under high pressure

    Energy Technology Data Exchange (ETDEWEB)

    Amaya, K.; Shimizu, K.; Takeda, K.; Tateiwa, N.; Muramatsu, T.; Ishizuka, M.; Kobayashi, T.C

    2003-05-01

    In part 1, we review techniques developed in our laboratory for producing the complex extreme condition of very low temperature and ultra-high pressure and those for measuring electrical resistance and magnetization of the sample confined in the extremely small space of the used pressure cell. In part 2, we review our experimental results in search for pressure-induced superconductivity, which have been obtained by the use of developed techniques. Typical examples are shown in the case of simple inorganic and organic molecular crystals, ionic crystals, and magnetic metals.

  17. High pressure induced superconductivity

    Energy Technology Data Exchange (ETDEWEB)

    Amaya, K.; Shimizu, K

    2003-10-15

    We have developed complex extreme condition of very low temperature down to 30 mK and ultra high pressure exceeding 200 GPa by assembling compact diamond anvil cell (DAC) on a powerful {sup 3}He/{sup 4}He dilution refrigerator. We have also developed measuring techniques of electrical resistance, magnetization and optical measurement for the sample confined in the sample space of the DAC. Using the newly developed apparatus and techniques, we have searched for superconductivity in various materials under pressure. In this paper, we will shortly review our newly developed experimental apparatus and techniques and discuss a few examples of pressure induced superconductivity which were observed recently.

  18. Tem Study of Recrystallization in Ultra-Fine Grain AA3104 Alloy Processed by High-Pressure Torsion

    Directory of Open Access Journals (Sweden)

    Paul H.

    2015-04-01

    Full Text Available The effect of annealing on the microstructure and the texture development was investigated in a particle containing AA3104 aluminium alloy. The samples were processed at room temperature by high-pressure torsion (HPT up to ten turns. The nucleation of new grains was analyzed by a transmission electron microscope equipped with a system for local orientation measurements and a heating holder.

  19. High-pressure x-ray diffraction study of LiIO sub 3 to 75 GPa

    CERN Document Server

    Zhang, W W; Pan Yue Wu; Dong, S S; Liu, J; Zou Guang Tian

    2002-01-01

    In situ high-pressure energy-dispersive x-ray diffraction measurements on alpha-LiIO sub 3 have been performed by using a diamond anvil cell device with synchrotron radiation up to 75 GPa at room temperature. No new phase was found. The second Birch-Murnaghan equation of state is fitted with B sub 0 = 55 +- 3 GPa for the zero-pressure bulk modulus, B sub 0 ' = 2.9 +- 0.4 for its pressure derivative.

  20. High pressure structural and magnetic studies of LaFe.sub.12./sub.B.sub.6./sub.

    Czech Academy of Sciences Publication Activity Database

    Diop, L.V.B.; Isnard, O.; Arnold, Zdeněk; Itié, J.P.; Kaštil, Jiří; Kamarád, Jiří

    2017-01-01

    Roč. 252, Feb (2017), s. 29-32 ISSN 0038-1098 R&D Projects: GA ČR GA15-03777S Institutional support: RVO:68378271 Keywords : itinerant-electron magnetism * magnetization * high pressure * compressibility Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 1.554, year: 2016

  1. A BEAMLINE FOR HIGH PRESSURE STUDIES AT THE ADVANCED LIGHT SOURCE WITH A SUPERCONDUCTING BENDING MAGNET AS THE SOURCE

    Energy Technology Data Exchange (ETDEWEB)

    Kunz, M; MacDowell, A A; Caldwell, W A; Cambie, D; Celestre, R S; Domning, E E; Duarte, R M; Gleason, A; Glossinger, J; Kelez, N; Plate, D W; Yu, T; Zaug, J M; Padmore, H A; Jeanloz, R; Alivisatos, A P; Clark, S M

    2005-04-19

    A new facility for high-pressure diffraction and spectroscopy using diamond anvil high-pressure cells has been built at the Advanced Light Source on Beamline 12.2.2. This beamline benefits from the hard X-radiation generated by a 6 Tesla superconducting bending magnet (superbend). Useful x-ray flux is available between 5 keV and 35 keV. The radiation is transferred from the superbend to the experimental enclosure by the brightness preserving optics of the beamline. These optics are comprised of: a plane parabola collimating mirror (M1), followed by a Kohzu monochromator vessel with a Si(111) crystals (E/{Delta}E {approx} 7000) and a W/B{sub 4}C multilayer (E/{Delta}E {approx} 100), and then a toroidal focusing mirror (M2) with variable focusing distance. The experimental enclosure contains an automated beam positioning system, a set of slits, ion chambers, the sample positioning goniometry and area detectors (CCD or image-plate detector). Future developments aim at the installation of a second end station dedicated for in situ laser-heating on one hand and a dedicated high-pressure single-crystal station, applying both monochromatic as well as polychromatic techniques.

  2. A Beamline for High-Pressure Studies at the Advanced Light Sourcewith a Superconducting Bending Magnet as the Source

    Energy Technology Data Exchange (ETDEWEB)

    Kunz, Martin; MacDowell, Alastair A.; Caldwell, Wendel A.; Cambie, Daniella; Celestre, Richard S.; Domning, Edward E.; Duarte,Robert M.; Gleason, Arianna E.; Glossinger, James M.; Kelez, Nicholas; Plate, David W.; Yu, Tony; Zaug, Joeseph M.; Padmore, Howard A.; Jeanloz,Raymond; Alivisatos, A. Paul; Clark, Simon M.

    2005-06-30

    A new facility for high-pressure diffraction and spectroscopy using diamond anvil high-pressure cells has been built at the Advanced Light Source on Beamline 12.2.2. This beamline benefits from the hard X-radiation generated by a 6 Tesla superconducting bending magnet (superbend). Useful x-ray flux is available between 5 keV and 35 keV. The radiation is transferred from the superbend to the experimental enclosure by the brightness preserving optics of the beamline. These optics are comprised of: a plane parabola collimating mirror (M1), followed by a Kohzu monochromator vessel with a Si(111) crystals (E/DE {approx}7000) and a W/B4C multilayers (E/DE {approx} 100), and then a toroidal focusing mirror (M2) with variable focusing distance. The experimental enclosure contains an automated beam positioning system, a set of slits, ion chambers, the sample positioning goniometry and area detectors (CCD or image-plate detector). Future developments aim at the installation of a second end station dedicated for in situ laser-heating on one hand and a dedicated high-pressure single-crystal station, applying both monochromatic as well as polychromatic techniques.

  3. High pressure ices are not the end of the story for large icy moons habitability: experimental studies of salts effects on high pressure ices and the implications for icy worlds large hydrosphere structure and chemical evolution

    Science.gov (United States)

    Journaux, Baptiste; Abramson, Evan; Brown, J. Michael; Bollengier, Olivier

    2017-10-01

    The presence of several phases of deep high-pressure ices in large icy moons hydrosphere has often been pointed as a major limitation for the habitability of an uppermost ocean. As they are gravitationally stable bellow liquid H2O, they are thought to act as a chemical barrier between the rocky bed and the ocean. Solutes, including salt species such as NaCl and MgSO4, have been suggested inside icy world oceans from remote sensing, magnetic field measurements and chondritic material alteration models. Unfortunately, the pressures and temperatures inside these hydrospheres are very different from the one found in Earth aqueous environments, so most of our current thermodynamic databases do not cover the range of conditions relevant for modeling realistically large icy worlds interiors.Recent experimental results have shown that the presence of solutes, and more particularly salts, in equilibrium with high pressure ices have large effects on the stability, buoyancy and chemistry of all the phases present at these extreme conditions.In particular brines have been measured to be sometimes more dense than the high pressure ices at melting conditions, possibly creating several oceanic layer "sandwiched" in between two ices shells or in contact with the rocky bed.Other effects currently being investigated by our research group also covers ice melting curve depressions that depend on the salt species and incorporation of solutes inside the crystallographic lattice of high pressure ices. Both of these could have very important implication at the planetary scale, enabling thicker/deeper liquid oceans, and allowing chemical transportation through the high pressure ice layer in large icy worlds.We will present the latest results obtained in-situ using diamond anvil cell high pressure allowing to probe the density, chemistry and thermodynamic properties of high pressure ice and aqueous solutions in equilibrium with Na-Mg-SO4-Cl ionic species.We will also discuss the new

  4. Brillouin scattering at high pressures

    International Nuclear Information System (INIS)

    Grimsditch, M.; Polian, A.

    1988-02-01

    Technical advances which have made Brillouin scattering a useful tool in high pressure diamond anvil cell (DAC) studies, viz. multipassing and tandem operation of Fabry-Perot interferometers, are reviewed. Experimental aspects, such as allowed scattering geometries, are outlined and the data analysis required to transform Brillouin spectra into sound velocities and elastic constants is presented. Experimental results on H 2 , N 2 , Ar, and He are presented, and the close relationship between the Brillouin scattering results and equations of state is highlighted

  5. High pressure mechanical seal

    Science.gov (United States)

    Babel, Henry W. (Inventor); Anderson, Raymond H. (Inventor)

    1996-01-01

    A relatively impervious mechanical seal is formed between the outer surface of a tube and the inside surface of a mechanical fitting of a high pressure fluid or hydraulic system by applying a very thin soft metal layer onto the outer surface of the hard metal tube and/or inner surface of the hard metal fitting. The thickness of such thin metal layer is independent of the size of the tube and/or fittings. Many metals and alloys of those metals exhibit the requisite softness, including silver, gold, tin, platinum, indium, rhodium and cadmium. Suitably, the coating is about 0.0025 millimeters (0.10 mils) in thickness. After compression, the tube and fitting combination exhibits very low leak rates on the order or 10.sup.-8 cubic centimeters per second or less as measured using the Helium leak test.

  6. Development of a hybrid-anvil type high-pressure device and its application to magnetic neutron scattering studies

    International Nuclear Information System (INIS)

    Osakabe, T.; Kakurai, K.; Kawana, D.; Kuwahara, K.

    2007-01-01

    A new hybrid-type anvil device for high-pressure single-crystal neutron diffraction experiments is described. The device is composed of a large sapphire anvil and a tungsten carbide (WC) anvil which has a hollow in the center of the culet. In a feasibility test of the device, we could generate the pressure up to 5GPa with high stability. As an example of the application of the hybrid-anvil device, we show some results of magnetic neutron diffraction experiments on filled skutterudite compound PrFe 4 P 12

  7. Possibilities and limitations of parametric Rietveld refinement on high pressure data. The case study of LaFeO3

    International Nuclear Information System (INIS)

    Etter, Martin; Mueller, Melanie; Dinnebier, Robert E.; Hanfland, Michael

    2014-01-01

    Parametric Rietveld refinement is a powerful technique to apply directly physical or empirical equations to the refinement of in situ powder diffraction data. In order to investigate the possibilities and limitations of parametric Rietveld refinements for high pressure data four competitive crystallographic approaches were used to carry out a full structural investigation of the orthoferrite LaFeO 3 (Pbnm at ambient conditions) under high pressure up to 47 GPa. Approach A with traditional Rietveld refinement using atomic coordinates, Approach B where the Rietveld refinement was done by using the rigid body method, Approach C where symmetry modes were used and Approach D where the newly developed method of the rotational symmetry mode description for a rigid body was used. For all approaches sequential as well as parametric refinements were carried out, confirming a second order phase transition of LaFeO 3 to a higher symmetric phase (space group Ibmm) at around 21.1?GPa and an isostructural first order phase transition at around 38 GPa. Limitations due to non-hydrostatic conditions as well as the possibilities of a direct modeling of phase transitions with parametric Rietveld refinement are discussed in detail. (orig.)

  8. Synchrotron X-ray diffraction studies of phase transitions and mechanical properties of nanocrystalline materials at high pressure

    Energy Technology Data Exchange (ETDEWEB)

    Prilliman, Stephen Gerald [Univ. of California, Berkeley, CA (United States)

    2003-01-01

    The behavior of nanocrystals under extreme pressure was investigated using synchrotron x-ray diffraction. A major part of this investigation was the testing of a prototype synchrotron endstation on a bend magnet beamline at the Advanced Light Source for high pressure work using a diamond anvil cell. The experiments conducted and documented here helped to determine issues of efficiency and accuracy that had to be resolved before the construction of a dedicated ''super-bend'' beamline and endstation. The major conclusions were the need for a cryo-cooled monochromator and a fully remote-controllable pressurization system which would decrease the time to change pressure and greatly reduce the error created by the re-placement of the diamond anvil cell after each pressure change. Two very different types of nanocrystal systems were studied, colloidal iron oxide (Fe2O3) and thin film TiN/BN. Iron oxide nanocrystals were found to have a transition from the γ to the α structure at a pressure strongly dependent on the size of the nanocrystals, ranging from 26 GPa for 7.2 nm nanocrystals to 37 GPa for 3.6 nm nanocrystals. All nanocrystals were found to remain in the α structure even after release of pressure. The transition pressure was also found, for a constant size (5.7 nm) to be strongly dependent on the degree of aggregation of the nanocrystals, increasing from 30 GPa for completely dissolved nanocrystals to 45 GPa for strongly aggregated nanocrystals. Furthermore, the x-ray diffraction pattern of the pressure induced α phase demonstrated a decrease in intensity for certain select peaks. Together, these observations were used to make a complete picture of the phase transition in nanocrystalline systems. The size dependence of the transition was interpreted as resulting from the extremely high surface energy of the α phase which would increase the thermodynamic offset and thereby increase the kinetic barrier to transition

  9. Synchrotron X-ray diffraction studies of phase transitions and mechanical properties of nanocrystalline materials at high pressure

    International Nuclear Information System (INIS)

    Prilliman, Gerald Stephen

    2003-01-01

    The behavior of nanocrystals under extreme pressure was investigated using synchrotron x-ray diffraction. A major part of this investigation was the testing of a prototype synchrotron endstation on a bend magnet beamline at the Advanced Light Source for high pressure work using a diamond anvil cell. The experiments conducted and documented here helped to determine issues of efficiency and accuracy that had to be resolved before the construction of a dedicated ''super-bend'' beamline and endstation. The major conclusions were the need for a cryo-cooled monochromator and a fully remote-controllable pressurization system which would decrease the time to change pressure and greatly reduce the error created by the re-placement of the diamond anvil cell after each pressure change. Two very different types of nanocrystal systems were studied, colloidal iron oxide (Fe 2 O 3 ) and thin film TiN/BN. Iron oxide nanocrystals were found to have a transition from the γ to the α structure at a pressure strongly dependent on the size of the nanocrystals, ranging from 26 GPa for 7.2 nm nanocrystals to 37 GPa for 3.6 nm nanocrystals. All nanocrystals were found to remain in the α structure even after release of pressure. The transition pressure was also found, for a constant size (5.7 nm) to be strongly dependent on the degree of aggregation of the nanocrystals, increasing from 30 GPa for completely dissolved nanocrystals to 45 GPa for strongly aggregated nanocrystals. Furthermore, the x-ray diffraction pattern of the pressure induced α phase demonstrated a decrease in intensity for certain select peaks. Together, these observations were used to make a complete picture of the phase transition in nanocrystalline systems. The size dependence of the transition was interpreted as resulting from the extremely high surface energy of the α phase which would increase the thermodynamic offset and thereby increase the kinetic barrier to transition that must be overridden with pressure

  10. New insights into the compressibility and high-pressure stability of Ni(CN)2: a combined study of neutron diffraction, Raman spectroscopy, and inelastic neutron scattering.

    Science.gov (United States)

    Mishra, Sanjay K; Mittal, Ranjan; Zbiri, Mohamed; Rao, Rekha; Goel, Prabhatasree; Hibble, Simon J; Chippindale, Ann M; Hansen, Thomas; Schober, Helmut; Chaplot, Samrath L

    2016-02-03

    Nickel cyanide is a layered material showing markedly anisotropic behaviour. High-pressure neutron diffraction measurements show that at pressures up to 20.1 kbar, compressibility is much higher in the direction perpendicular to the layers, c, than in the plane of the strongly chemically bonded metal-cyanide sheets. Detailed examination of the behaviour of the tetragonal lattice parameters, a and c, as a function of pressure reveal regions in which large changes in slope occur, for example, in c(P) at 1 kbar. The experimental pressure dependence of the volume data is fitted to a bulk modulus, B0, of 1050 (20) kbar over the pressure range 0-1 kbar, and to 124 (2) kbar over the range 1-20.1 kbar. Raman spectroscopy measurements yield additional information on how the structure and bonding in the Ni(CN)2 layers change with pressure and show that a phase change occurs at about 1 kbar. The new high-pressure phase, (Phase PII), has ordered cyanide groups with sheets of D4h symmetry containing Ni(CN)4 and Ni(NC)4 groups. The Raman spectrum of phase PII closely resembles that of the related layered compound, Cu1/2Ni1/2(CN)2, which has previously been shown to contain ordered C≡N groups. The phase change, PI to PII, is also observed in inelastic neutron scattering studies which show significant changes occurring in the phonon spectra as the pressure is raised from 0.3 to 1.5 kbar. These changes reflect the large reduction in the interlayer spacing which occurs as Phase PI transforms to Phase PII and the consequent increase in difficulty for out-of-plane atomic motions. Unlike other cyanide materials e.g. Zn(CN)2 and Ag3Co(CN)6, which show an amorphization and/or a decomposition at much lower pressures (~100 kbar), Ni(CN)2 can be recovered after pressurising to 200 kbar, albeit in a more ordered form.

  11. High Pressure Scanning Tunneling Microscopy Studies of AdsorbateStructure and Mobility during Catalytic Reactions: Novel Design of anUltra High Pressure, High Temperature Scanning Tunneling MicroscopeSystem for Probing Catalytic Conversions

    Energy Technology Data Exchange (ETDEWEB)

    Tang, David Chi-Wai [Univ. of California, Berkeley, CA (United States)

    2005-05-16

    The aim of the work presented therein is to take advantage of scanning tunneling microscope’s (STM) capability for operation under a variety of environments under real time and at atomic resolution to monitor adsorbate structures and mobility under high pressures, as well as to design a new generation of STM systems that allow imaging in situ at both higher pressures (35 atm) and temperatures (350 °C).

  12. Neutron diffraction and electrical transport studies on the incommensurate magnetic phase transition in holmium at high pressures

    International Nuclear Information System (INIS)

    Thomas, Sarah A; Uhoya, Walter O; Tsoi, Georgiy M; Wenger, Lowell E; Vohra, Yogesh K; Chesnut, Gary N; Weir, Samuel T; Tulk, Christopher A; Dos Santos, Antonio M

    2012-01-01

    Neutron diffraction and electrical transport measurements have been made on the heavy rare earth metal holmium at high pressures and low temperatures in order to elucidate its transition from a paramagnetic (PM) to a helical antiferromagnetic (AFM) ordered phase as a function of pressure. The electrical resistance measurements show a change in the resistance slope as the temperature is lowered through the antiferromagnetic Néel temperature. The temperature of this antiferromagnetic transition decreases from approximately 122 K at ambient pressure at a rate of -4.9 K GPa -1 up to a pressure of 9 GPa, whereupon the PM-to-AFM transition vanishes for higher pressures. Neutron diffraction measurements as a function of pressure at 89 and 110 K confirm the incommensurate nature of the phase transition associated with the antiferromagnetic ordering of the magnetic moments in a helical arrangement and that the ordering occurs at similar pressures as determined from the resistance results for these temperatures. (paper)

  13. Neutron diffraction and electrical transport studies on the incommensurate magnetic phase transition in holmium at high pressures.

    Science.gov (United States)

    Thomas, Sarah A; Uhoya, Walter O; Tsoi, Georgiy M; Wenger, Lowell E; Vohra, Yogesh K; Chesnut, Gary N; Weir, Samuel T; Tulk, Christopher A; dos Santos, Antonio M

    2012-05-30

    Neutron diffraction and electrical transport measurements have been made on the heavy rare earth metal holmium at high pressures and low temperatures in order to elucidate its transition from a paramagnetic (PM) to a helical antiferromagnetic (AFM) ordered phase as a function of pressure. The electrical resistance measurements show a change in the resistance slope as the temperature is lowered through the antiferromagnetic Néel temperature. The temperature of this antiferromagnetic transition decreases from approximately 122 K at ambient pressure at a rate of -4.9 K GPa(-1) up to a pressure of 9 GPa, whereupon the PM-to-AFM transition vanishes for higher pressures. Neutron diffraction measurements as a function of pressure at 89 and 110 K confirm the incommensurate nature of the phase transition associated with the antiferromagnetic ordering of the magnetic moments in a helical arrangement and that the ordering occurs at similar pressures as determined from the resistance results for these temperatures.

  14. Octene hydroformylation by using rhodium complexes tethered onto selectively functionalized mesoporous silica and in-situ high pressure IR study

    Energy Technology Data Exchange (ETDEWEB)

    Song, Ki-Chang; Baek, Ji Yeon; Bae, Jung A.; Yim, Jin-Heong; Ko, Young Soo; Kim, Do Heui; Park, Young-Kwon; Jeon, Jong Ki

    2011-04-30

    SBA-15-based heterogeneous catalysts were applied to 1-octene hydroformylation. The turn over frequency over SBA-15/γ-aminopropylmethyldimethoxysilane(AEAPMDMS)/Rh catalyst with triphenylphosphine (TPP) ligand prepared by conventional post grafting method was higher than that of the homogeneous catalyst, (Rh(CH3COO)2)2 with TPP. The SBA-15/AEAPMDMS/Rh catalyst can be easily recycled without rhodium loss. The molar ratio of linear to branched nonyl aldehydes was remarkably enhanced over the heterogeneous catalysts. The selectively functionalized rhodium catalyst (SBA-15/Ph2Si(OEt)2/AEAPMDMS/Rh), in which rhodium was selectively tethered intra-pore of SBA-15, was beneficial for improving the selectivity to linear aldehyde. In situ high pressure FT-IR analysis suggested HRh(CO)2(PPh3)2 and HRh(CO)(PPh3)3 to be active species over the SBA-15/AEAPMDMS/Rh catalyst with TPP.

  15. Pressure and Temperature Dependent Structural Studies on Hollandite Type Ferrotitanate and Crystal Structure of a High Pressure Phase.

    Science.gov (United States)

    Bevara, Samatha; Achary, S Nagabhusan; Garg, Nandini; Chitnis, Abhishek; Sastry, P U; Shinde, A B; Krishna, P Siva Ram; Tyagi, Avesh Kumar

    2018-02-19

    The structural stability and phase transition behavior of tetragonal (I4/m) hollandite type K 2 Fe 2 Ti 6 O 16 have been investigated by in situ high pressure X-ray diffraction using synchrotron radiation and a diamond anvil cell as well as by variable temperature powder neutron and X-ray diffraction. The tetragonal phase is found to be stable in a wider range of temperatures, while it reversibly transforms to a monoclinic (I2/m) structure at a moderate pressure, viz. 3.6 GPa. The pressure induced phase transition occurs with only a marginal change in structural arrangements. The unit cell parameters of ambient (t) and high pressure (m) phases can be related as a m ∼ a t , b m ∼ c t , and c m ∼ b t . The pressure evolution of the unit cell parameters indicates anisotropic compression with β a = β b ≥ β c in the tetragonal phase and becomes more anisotropic with β a ≪ β b pressure-volume equations of state of both phases have been obtained by second order Birch-Murnaghan equations of state, and the bulk moduli are 122 and 127 GPa for tetragonal and monoclinic phases, respectively. The temperature dependent unit cell parameters show nearly isotropic expansion, with marginally higher expansion along the c-axis compared to the a- and b-axes. The tetragonal to monoclinic phase transition occurs with a reduction of unit cell volume of about 1.1% while the reduction of unit cell volume up to 6 K is only about 0.6%. The fitting of temperature dependent unit cell volume by using the Einstein model of phonons indicates the Einstein temperature is about 266(18) K.

  16. Effect of high pressure on the ground state of low doped manganite: a neutron diffraction and transport property study

    International Nuclear Information System (INIS)

    Ghosh, Barnali; Raychaudhuri, A.K.; Siruguri, V.; Chatterji, Tapan; Thomas, Hansen; Mukovskii, Ya.M.

    2013-01-01

    Depending on the doping level x the hole-doped perovskite manganites, like La 1-x Ca x MnO 3 exhibit a wide variety of physical properties. These compounds lead their high sensitivity to thermodynamic variables like temperature, magnetic field and pressure. The structure can be modified by application of high pressure and it can be quantitative that changes the Mn-O bond length and increases the Mn-O-Mn bond angle. In some cases the pressure can bring about qualitative changes in the structure like change in the lattice structure or its symmetry. These structural factors can contribute to the effective electron transfer integral between Mn ions, which in turn can change the magnetic exchanges like the double-exchange as well as the super exchange. For low hole doping (0.15 ≤ x ≤ 0.2), the low temperature ground state is Ferromagnetic insulator (FMI). The ground state of the low doped manganite La 0.79 Ca 0.21 MnO 3 (LCMO) can be destabilized by external hydrostatic pressure. We have done electrical transport measurement under magnetic field and under high pressure for understanding the nature of the resulting phase(s) that arise from the applied hydrostatic pressure. We find that the metallic phase so created under pressure has no appreciable magnetoresistance (MR). The Neutron powder diffraction measurement done on D20 diffractometer (λ=1.3Å) at ILL, Grenoble, France under high hydrostatic pressure up to 10GPa shows that the pressure leads to a change in the crystal structure from orthorhombic to rhombohedral and leading to a change in magnetic structure also; and most importantly collapse of the magnetic moment to a low value that leads to absence of any MR under pressure induced metallization. (author)

  17. High pressure cosmochemistry of major planetary interiors: Laboratory studies of the water-rich region of the system ammonia-water

    Science.gov (United States)

    Nicol, Malcolm; Johnson, Mary; Boone, Steven; Cynn, Hyunchee

    1987-01-01

    Several studies relative to high pressure cosmochemistry of major planetary interiors are summarized. The behavior of gas-ice mixtures at very high pressures, studies of the phase diagram of (NH3) sub x (H2O) sub 1-x at pressures to 5GPa and temperatures from 240 to 370 K, single crystal growth of ammonia dihydrate at room temperature in order to determine their structures by x-ray diffraction, spectroscopy of chemical reactions during shock compression in order to evaluate how the reactions affect the interpretation of equation of state data obtained by shock methods, and temperature and x-ray diffraction measurements made on resistively heated wire in diamond anvil cells in order to obtain phase and structural data relevant to the interiors of terrestrial planets are among the studies discussed.

  18. Study of the earth's deep interior and crystallography. X-ray and neutron diffraction experiments under high pressures

    International Nuclear Information System (INIS)

    Yagi, Takehiko

    2014-01-01

    History of the study of the Earth's deep interior was reviewed. In order to understand Earth's deep interior from the view point of materials science, X-ray diffraction under high pressure and high temperature played very important role. Use of synchrotron radiation dramatically advanced this experimental technique and it is now possible to make precise X-ray study under the P-T conditions corresponding even to the center of the Earth. In order to clarify the behavior of light elements such as hydrogen, however, studies using neutron diffraction are also required. A new neutron beam line dedicated for high-pressure science is constructed at J-PARC and is now ready for use. (author)

  19. High pressure neutron powder diffraction study of Fe1-xCrx with and without hydrogen exposure

    Energy Technology Data Exchange (ETDEWEB)

    Rivin, Oleg [Nuclear Research Centre, Negev (Israel); Broide, Amir [Ben Gurion Univ., Beersheba (Israel); Maskova, Sylvie [Charles Univ., Prague (Czech Republic); Lucas, Matthew [Air Force Research Lab. (AFRL), Wright-Patterson AFB, OH (United States); Hen, Amir [Ben Gurion Univ., Beersheba (Israel); Orion, Itzhak [Ben Gurion Univ., Beersheba (Israel); Salhov, Shai [Nuclear Research Centre, Negev(Israel); Shandalov, Michael [Nuclear Research Centre, Negev(Israel); Moreira Dos Santos, Antonio F. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Molaison, Jamie J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Chen, Zhiqiang [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Halevy, Itzhak [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2014-12-23

    The crystal structure of Fe1-xCrx(x = 0, 0.2 and 0.4) materials, with and without exposure to Hydrogen, is investigated using neutron powder diffraction under the applied external high-pressure. Above a certain applied pressure, PC, a structural phase transition, from cubic to hexagonal symmetry, is observed, in agreement with previous x-ray diffraction results. The PC values exhibit an increase with x increase. The possibility for an evolution of a magnetic structure with pressure, x and Hydrogen exposure, is examined. Finally, a broadening of the angular profile of the (200) reflection (cubic phase) is identified and reported.

  20. High pressure experimental water loop

    International Nuclear Information System (INIS)

    Grenon, M.

    1958-01-01

    A high pressure experimental water loop has been made for studying the detection and evolution of cladding failure in a pressurized reactor. The loop has been designed for a maximum temperature of 360 deg. C, a maximum of 160 kg/cm 2 and flow rates up to 5 m 3 /h. The entire loop consists of several parts: a main circuit with a canned rotor circulation pump, steam pressurizer, heating tubes, two hydro-cyclones (one de-gasser and one decanter) and one tubular heat exchanger; a continuous purification loop, connected in parallel, comprising pressure reducing valves and resin pots which also allow studies of the stability of resins under pressure, temperature and radiation; following the gas separator is a gas loop for studying the recombination of the radiolytic gases in the steam phase. The preceding circuits, as well as others, return to a low pressure storage circuit. The cold water of the low pressure storage flask is continuously reintroduced into the high pressure main circuit by means of a return pump at a maximum head of 160 kg /cm 2 , and adjusted to the pressurizer level. This loop is also a testing bench for the tight high pressure apparatus. The circulating pump and the connecting flanges (Oak Ridge type) are water-tight. The feed pump and the pressure reducing valves are not; the un-tight ones have a system of leak recovery. To permanently check the tightness the circuit has been fitted with a leak detection system (similar to the HRT one). (author) [fr

  1. Study on interfacial heat transfer coefficient at metal/die interface during high pressure die casting process of AZ91D alloy

    Directory of Open Access Journals (Sweden)

    GUO Zhi-peng

    2007-02-01

    Full Text Available The high pressure die casting (HPDC process is one of the fastest growing and most efficient methods for the production of complex shape castings of magnesium and aluminum alloys in today’s manufacturing industry.In this study, a high pressure die casting experiment using AZ91D magnesium alloy was conducted, and the temperature profiles inside the die were Measured. By using a computer program based on solving the inverse heat problem, the metal/die interfacial heat transfer coefficient (IHTC was calculated and studied. The results show that the IHTC between the metal and die increases right after the liquid metal is brought into the cavity by the plunger,and decreases as the solidification process of the liquid metal proceeds until the liquid metal is completely solidified,when the IHTC tends to be stable. The interfacial heat transfer coefficient shows different characteristics under different casting wall thicknesses and varies with the change of solidification behavior.

  2. High-Pressure Study of Bio-inspired Multi-Functional Nanocomposites Using Atomic Force Microscopy Methods

    Science.gov (United States)

    Diaz Gonzalez, Alfredo J.

    Bioinspired design has been crucial in the development of new types of hierarchical nanocomposites. Particularly, the nacre-mimetic brick-and-mortar structure has shown excellent mechanical properties as well as gas barrier properties and optical transparency. Along with these intrinsic properties, the layered structure has been designed to serve as sensing devices. Here we expand the multi-functionality of nacre-mimetics by designing an optically transparent and electron conductive coating that reacts to high-pressure based on PEDOT:PSS and nanoclay. The main objectives of this project are: (i) to develop a multifunctional nanocomposite and evaluate the effect of high-pressure applied at the surface and (ii) to establish protocols for the morphological and structural characterization, and electro-mechanical testing of the nanocomposites based on a combination of atomic force microscopy (AFM), scanning electron microscopy (SEM) and transmittance spectroscopy. The synthesis of the nanocomposite, containing PEDOT:PSS (conductive polymer) and nanoclay, was achieved using the self-assembly of core/shell platelets. Two different types of nanoclay, Cloisite Na+ and Laponite RD, are used and their properties compared. The reduction of thickness in PEDOT:PSS has been shown to increase the light transmittance across a film. Similarly, the thickness of the nanocomposite was reduced and compared to PEDOT:PSS. The measured optical transmittance for both nanocomposites is comparable to the bare polymer, demonstrating that the addition of the nanoclay does not affect the transparency of PEDOT:PSS significantly. The layered structure of the nanocomposites is investigated by imaging the fracture surface with SEM. The fracture surface of the Laponite RD based nanocomposite is much flatter than the Cloisite Na+ nanocomposite, since the particle size in Cloisite Na+ is about 10 times larger than Laponite RD. The characterization of electro-mechanical properties of the nanocomposites

  3. A High-Pressure Study of Manganese Metal and its Reactions with CO2 at 6, 23, and 44 GPa

    Science.gov (United States)

    Sawchuk, K. L. S.; McGuire, C. P.; Greenburg, A.; Makhluf, A.; Kavner, A.

    2017-12-01

    The free energies of formation of oxides and carbonates at the extreme pressures and temperatures of Earth's interior provides some of the thermodynamic constrains for models of mantle/core formation and subsequent chemical evolution. The broad goal of our research program is to measure the pressure- and temperature-dependence of free energies of formation of transition metal oxides and carbonates. This requires measurements of the phase stability, density, and thermoelastic properties of metals, oxides, and carbonates at deep-Earth and planetary conditions. Manganese is of interest because it is one of the most abundant transition metal geochemical tracers, it readily forms a carbonate at ambient pressure, and its high-pressure carbonate and oxide densities and equation of state parameters are relatively unknown. Here we report new data on the pressure/volume equation of state and structure of manganese metal as well as its reactions with CO2. These measurements were made using a laser heated diamond anvil cell in conjunction with synchrotron-based X-ray diffraction at beamline 12.2.2 at the Advanced Light Source. Three samples of manganese metal were gas-loaded in a CO2 pressure medium and pressurized to 6, 23, and 44 GPa. Upon laser heating, the CO2 reacted with the Mn metal generating new phases. To analyze the diffraction patterns, we we use a python-based program developed in-house for extracting high resolution 2-dimensional diffraction peak position and intensity information from two-dimensional X-ray diffraction patterns. At each pressure step, the structure and density of the quenched Mn metal phase was determined. At 6 GPa, Mn metal adopts a BCC structure, and at 23 GPa a tetragonal distortion is observed in the lattice. The measured equation of state is in good agreement with an existing meaurement by Fujihisa and Takemura (1995). MnCO3 rhodochrosite is observed in the sample quenched after heating at 6 GPa. Additional high pressure phases are evident

  4. Neutron diffraction study of structural transformations in ternary systems of HgSe sub 1 sub - sub x S sub x mercury chalcogenides at high pressure

    CERN Document Server

    Voronin, V I; Berger, I F; Glazkov, V P; Kozlenko, D P; Savenko, B N; Tikhomirov, S V

    2001-01-01

    The structure of the ternary systems of the HgSe sub 1 sub - sub x S sub x mercury chalcogenides is studied at high pressures up to 35 kbar. It is established that by increase in the pressure in the HgSe sub 1 sub - sub x S sub x there takes place the transition from the sphalerite type cubic structure to the cinnabar type hexagonal structure, which is accompanied by the jump-like change in the elementary cell volume and interatomic distances. The parameters of the elementary cell and positional parameters of the Hg and Se/S for the hexagonal phase of high pressure are determined. The existence of the two-phase state in the area of the phase transformation is determined

  5. Does high pressure have any effect on the structure of alpha amylase and its ability to binding to the oligosaccharides having 3-7 residues? Molecular dynamics study.

    Science.gov (United States)

    Vahidi, S Hooman; Bozorgmehr, Mohammad Reza; Morsali, Ali; Beyramabadi, S Ali

    2018-03-01

    Studies have shown that deletion of amino acids from the C-terminus of amylase do not alter its amylolytic activity. Although high pressure is used to modify the structure and function of this enzyme, the effects of high pressures on the structures of the wild-type and truncated amylases have not yet been understood at the molecular level. Using molecular dynamic simulations and docking, we studied the structures of wild-type and truncated Taka-amylases at high pressures (1000-4000 bar). To construct the truncated Taka-amylase, 50 and 100 C-terminal residues were removed in two separate steps. Results of simulation showed that, although the overall shape partly agglomerates with rise in pressure, high pressure fails to modify the structure of the barrel-like region of the β-sheet in the wild-type and truncated enzymes. A comparison of contact graphs revealed that the changes at the N-terminus were less extensive than those at the C-terminus. Further analysis showed that 10 regions of the secondary structures changed due to pressure change in wild-type amylase, of which 6 regions were associated with the loops and 4 with helix, while the structure of β-sheets remained unchanged. The docking of maltotriose, maltotetraose, maltopentaose, maltohexaose, and maltoheptaose with the averaged structures obtained from different simulations was conducted to characterize the influence of pressure on the activities of the wild-type and truncated enzymes. The results showed that maltoheptaose made hydrophobic contacts with residues Tyr238-Asp117-Tyr82-Leu166-Leu232-Tyr155 and hydrogen contacts with residues Asp233-Gly234-Asp206-Arg204-His296-Glu230. Similar results were obtained for other malto-oligosaccharides. Copyright © 2018 Elsevier Inc. All rights reserved.

  6. High-pressure Raman study of the quantum magnet (C4H12N2) Cu2Cl6

    Science.gov (United States)

    Bettler, S.; Simutis, G.; Perren, G.; Blosser, D.; Gvasaliya, S.; Zheludev, A.

    2017-11-01

    Magnetic and lattice excitations in the quantum antiferromagnet (C4H12N2) Cu2Cl6 (PHCC) are studied across two pressure-induced phase transition at Pc=4.3 kbar and P1=13.4 kbar using Raman spectroscopy. It is confirmed that neither transition is a result of a structural transformation. Magnetic scattering is detected. It shows a pronounced pressure dependence and undergoes substantial changes at both transitions. The results are in clear contradiction with previous neutron studies, which detected only minor changes of the magnon spectrum at P1. A number of phonons show anomalous frequency shifts at low temperatures. This effect is pressure dependent and for two of the observed phonons dramatically reverses sign at around P1. The anomalous behavior is attributed to strong magnetoelastic coupling in PHCC.

  7. Series of phase transitions in cesium azide under high pressure studied by in situ x-ray diffraction

    Science.gov (United States)

    Hou, Dongbin; Zhang, Fuxiang; Ji, Cheng; Hannon, Trevor; Zhu, Hongyang; Wu, Jianzhe; Ma, Yanzhang

    2011-08-01

    In situ x-ray diffraction measurements of cesium azide (CsN3) were performed at high pressures of up to 55.4 GPa at room temperature. Three phase transitions were revealed as follows: tetragonal (I4/mcm, Phase II) → monoclinic (C2/m, Phase III) → monoclinic (P21/m or P21, Phase IV) → triclinic (P1 or P1¯, Phase V), at 0.5, 4.4, and 15.4 GPa, respectively. During the II-III phase transition, CsN3 keeps its layered structure and the azide anions rotate obviously. The compressibility of Phase II is dominated by the repulsions between azide anions. The deformation of unit cell is isotropic in Phases II and IV and anisotropic in Phase III. With increasing pressures, the monoclinic angle increases in Phase III and then becomes stable in Phase IV. The bulk moduli of Phases II, III, IV, and V are determined to be 18 ± 4, 20 ± 1, 27 ± 1 and 34 ± 1 GPa, respectively. The ionic character of alkali azides is found to play a key role in their pressure-induced phase transitions.

  8. Hydrogen bond symmetrization and superconducting phase of HBr and HCl under high pressure: An ab initio study.

    Science.gov (United States)

    Duan, Defang; Tian, Fubo; He, Zhi; Meng, Xing; Wang, Liancheng; Chen, Changbo; Zhao, Xiusong; Liu, Bingbing; Cui, Tian

    2010-08-21

    Ab initio calculations are performed to probe the hydrogen bonding, structural, and superconducting behaviors of HBr and HCl under high pressure. The calculated results show that the hydrogen bond symmetrization (Cmc2(1)-->Cmcm transition) of HBr and HCl occurs at 25 and 40 GPa, respectively, which can be attributed to the symmetry stretching A(1) mode softening. After hydrogen bond symmetrization, a pressure-induced soft transverse acoustic phonon mode of Cmcm phase is identified and a unique metallic phase with monoclinic structure of P2(1)/m (4 molecules/cell) for both compounds is revealed by ab initio phonon calculations. This phase preserves the symmetric hydrogen bond and is stable in the pressure range from 134 to 196 GPa for HBr and above 233 GPa for HCl, while HBr is predicted to decompose into Br(2)+H(2) above 196 GPa. Perturbative linear-response calculations predict that the phase P2(1)/m is a superconductor with T(c) of 27-34 K for HBr at 160 GPa and 9-14 K for HCl at 280 GPa.

  9. Equilibrium studies on liquid ammonia-potassium amide-hydrogen system at high pressures and temperatures (Preprint No. CA-10)

    International Nuclear Information System (INIS)

    Donde, M.M.; Srinivasa, K.; Raman, S.

    1989-04-01

    Insoluble deposits were observed to form during the operation of Heavy Water Plant at Talcher, based on ammonia-hydrogen exchange process with potassium amide as catalyst. Experiments were undertaken to investigate this phenomenon under controlled conditions in the laboratory employing high pressures and elevated temperatures. It was observed that deposit formation was very minimal in the autoclave and no visible deposit was left on the strainer-filter, in all the experiments. Deposit analysis showed the presence of potassium hydroxide monohydrate as major component and alpha-potassium hydroxide and potassium azide as minor components. It is suggested that the presence of hydroxide may be due to the reaction of amide with the residual moisture in the system during the experiment and any ingress of moisture while opening for collection of deposit. Azide formation is explained by following reactions occurring during the experiments. NH 3 +KNH 2 →NH 2 -NH 2 +KH; NH 2 -NH 2 +KNH 2 →KN 3 +3H 2 . (author). 1 fig

  10. High-pressure behaviour of selenium-based spinels and related structures - an experimental and theoretical study

    International Nuclear Information System (INIS)

    Waskowska, A; Gerward, L; Olsen, J Staun; Feliz, M; Llusar, R; Gracia, L; Marques, M; Recio, J M

    2004-01-01

    The high-pressure structural behaviour of the cubic spinel CdCr 2 Se 4 (space group Fd3barm) and tetragonal CdGa 2 Se 4 (I4bar) has been investigated experimentally and theoretically in order to understand the large difference in compressibility between the two selenides. The experimental values of the bulk modulus for these compounds are 101(2) and 48(2) GPa, respectively. These values compare well with 92 and 44 GPa obtained from first-principles calculations based on the density functional theory formalism. The observed difference in compressibility between the cubic and tetragonal structures can be understood in terms of polyhedral analysis. In a hypothetical cubic spinel structure Fd3barm), the calculated bulk modulus for CdGa 2 Se 4 is 85 GPa. This value together with the experimental and theoretical results for CdCr 2 Se 4 suggest that the selenium-based cubic spinels should have a bulk modulus about 100 GPa, which is half the value found for the oxide spinels

  11. Ultraviolet (UV) Raman Spectroscopy Study of the Soret Effect in High-Pressure CO2-Water Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Windisch, Charles F.; Maupin, Gary D.; McGrail, B. Peter

    2012-07-01

    Spatially resolved deep-UV Raman spectroscopy was applied to solutions of CO2 and H2O or D2O subject to a temperature gradient in a thermally regulated high-pressure concentric-tube Raman cell in an attempt to measure a Soret effect in the vicinity of the critical point of CO2. Although Raman spectra of solutions of CO2 dissolved in D2O, at 10 MPa and temperatures near the critical point of CO2, had adequate signal-to-noise and spatial resolution to observe a Soret effect with a Soret coefficient with magnitude |ST| > 0.03, no evidence for an effect of this size was obtained for applied temperature gradients up to 19 C. In contrast, the concentration of CO2 dissolved in H2O was shown to vary significantly across the temperature gradient when excess CO2 was present, but the results could be explained simply by the variation in CO2 solubility over the temperature range and not to kinetic factors. For mixtures of D2O dissolved in scCO2 at 10 MPa and temperatures close to the critical point of CO2, the Raman peaks for D2O were too weak to measure with confidence even at the limit of D2O solubility.

  12. High-pressure behaviour of selenium-based spinels and related structures - an experimental and theoretical study

    Energy Technology Data Exchange (ETDEWEB)

    Waskowska, A [Institute of Low Temperature and Structure Research, Polish Academy of Sciences, 50 422 Wroclaw (Poland); Gerward, L [Department of Physics, Technical University of Denmark, 2800 Kongens Lyngby, Denmark (Denmark); Olsen, J Staun [Niels Bohr Institute, Oersted Laboratory, University of Copenhagen, 2100 Copenhagen (Denmark); Feliz, M [Universitat Jaume I - Campus de Riu Sec, Departament de Ciences Experimentals, Apartat 224, Castellon (Spain); Llusar, R [Universitat Jaume I - Campus de Riu Sec, Departament de Ciences Experimentals, Apartat 224, Castellon (Spain); Gracia, L [Universitat Jaume I - Campus de Riu Sec, Departament de Ciences Experimentals, Apartat 224, Castellon (Spain); Marques, M [Departamento de QuImica FIsica y AnalItica, Universidad de Oviedo, E-33006 Oviedo (Spain); Recio, J M [Departamento de QuImica FIsica y AnalItica, Universidad de Oviedo, E-33006 Oviedo (Spain)

    2004-01-14

    The high-pressure structural behaviour of the cubic spinel CdCr{sub 2}Se{sub 4} (space group Fd3barm) and tetragonal CdGa{sub 2}Se{sub 4} (I4bar) has been investigated experimentally and theoretically in order to understand the large difference in compressibility between the two selenides. The experimental values of the bulk modulus for these compounds are 101(2) and 48(2) GPa, respectively. These values compare well with 92 and 44 GPa obtained from first-principles calculations based on the density functional theory formalism. The observed difference in compressibility between the cubic and tetragonal structures can be understood in terms of polyhedral analysis. In a hypothetical cubic spinel structure Fd3barm), the calculated bulk modulus for CdGa{sub 2}Se{sub 4} is 85 GPa. This value together with the experimental and theoretical results for CdCr{sub 2}Se{sub 4} suggest that the selenium-based cubic spinels should have a bulk modulus about 100 GPa, which is half the value found for the oxide spinels.

  13. High-Pressure Study of Perovskites and Postperovskites in the (Mg,Fe)GeO 3 System

    Energy Technology Data Exchange (ETDEWEB)

    Stan, Camelia V.; Dutta, Rajkrishna; Cava, Robert J.; Prakapenka, Vitali B.; Duffy, Thomas S. (Princeton); (UC)

    2017-06-22

    The effect of incorporation of Fe2+ on the perovskite (Pbnm) and postperovskite (Cmcm) structures was investigated in the (Mg,Fe)GeO3 system at high pressures and temperatures using laser-heated diamond anvil cell and synchrotron X-ray diffraction. Samples with compositions of Mg# ≥ 48 were shown to transform to the perovskite (~30 GPa and ~1500 K) and postperovskite (>55 GPa, ~1600–1800 K) structures. Compositions with Mg# ≥ 78 formed single-phase perovskite and postperovskite, whereas those with Mg# < 78 showed evidence for partial decomposition. The incorporation of Fe into the perovskite structure causes a decrease in octahedral distortion as well as a modest decrease in bulk modulus (K0) and a modest increase in zero-pressure volume (V0). It also leads to a decrease in the perovskite-to-postperovskite phase transition pressure by ~9.5 GPa over compositions from Mg#78 to Mg#100.

  14. Design of high pressure waterjet nozzles

    Science.gov (United States)

    Mazzoleni, Andre P.

    1994-10-01

    The Hydroblast Research Cell at Marshall Space Flight Center is used to investigate the use of high pressure waterjets to strip paint, grease, adhesive and thermal spray coatings from various substrates. Current methods of cleaning often use ozone depleting chemicals (ODC) such as chlorinated solvents. High pressure waterjet cleaning has proven to be a viable alternative to the use of solvents. A popular method of waterjet cleaning involves the use of a rotating, multijet, high pressure water nozzle which is robotically controlled. This method enables rapid cleaning of a large area, but problems such as incomplete coverage and damage to the substrate from the waterjet have been observed. This report summarizes research consisting of identifying and investigating the basic properties of rotating, multijet, high pressure water nozzles, and how particular designs and modes of operation affect such things as stripping rate, standoff distance and completeness of coverage. The study involved computer simulations, an extensive literature review, and experimental studies of different nozzle designs.

  15. High Pressure Research on Materials

    Indian Academy of Sciences (India)

    ing high pressure are described. Empirical equations of state. (EOS) are illustrated for some standard materials. 1. Introduction. Pressure, like temperature is an important thermodynamic param- eter in our daily life. We use pressure cookers in our kitchen to cook food and use gas cylinders containing LPG at high pressures.

  16. High Pressure Research on Materials

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 12; Issue 6. High Pressure Research on Materials - Production and Measurement of High Pressures in the Laboratory. P Ch Sahu N V Chandra Shekar. General Article Volume 12 Issue 6 June 2007 pp 10-23 ...

  17. Equation of state and electronic properties of EuVO{sub 4}: A high-pressure experimental and computational study

    Energy Technology Data Exchange (ETDEWEB)

    Paszkowicz, Wojciech, E-mail: paszk@ifpan.edu.pl [Institute of Physics, Polish Academy of Sciences, al. Lotników 32/46, 02-668 Warsaw (Poland); López-Solano, Javier [Departamento de Física, MALTA Consolider Team, and Instituto de Materiales y Nanotecnología, Universidad de La Laguna, Tenerife 38205 (Spain); Izaña Atmospheric Research Center, Agencia Estatal de Meteorología (AEMET), Tenerife 38071 (Spain); Piszora, Paweł [Department of Materials Chemistry, Faculty of Chemistry, Adam Mickiewicz University, Umultowska 89b, 61-614 Poznań (Poland); Bojanowski, Bohdan [Institute of Physics, Szczecin University of Technology, Aleja Piastów 48, 70-310 Szczecin (Poland); Mujica, Andrés; Muñoz, Alfonso [Departamento de Física, MALTA Consolider Team, and Instituto de Materiales y Nanotecnología, Universidad de La Laguna, Tenerife 38205 (Spain); Cerenius, Yngve; Carlson, Stefan [MAX IV Laboratory, Lund University, P.O. Box 118, SE-221 00 Lund (Sweden); Dąbkowska, Hanna [Brockhouse Institute for Materials Research, McMaster University, Hamilton, Ontario L8S 4M1 (Canada)

    2015-11-05

    Structural, elastic and electronic properties of zircon-type and scheelite-type EuVO{sub 4} are investigated experimentally, by in-situ X-ray diffraction using synchrotron radiation, and theoretically within the framework of the density functional theory (DFT) and using the PBE prescription of the exchange-correlation energy. This study was motivated by the fact that the previous knowledge of the equation of state (EOS) was inconclusive due to a large scatter of the experimental and theoretical data, and by the lack of information on the dependence of the electronic structure with pressure. Under the applied experimental conditions, the zircon-type structure transforms to a scheelite-type one at 7.4(2) GPa, whereas the calculations yield a lower zircon–scheelite-coexistence pressure of 4.8 GPa. The experimental part of the study shows that the bulk modulus of the zircon-type phase is 119(3) GPa, perfectly supported by the DFT-calculated value, 119.1 GPa. The bulk modulus for the scheelite-type polymorph is higher, with an experimental value of 135(7) GPa and a theoretical one of 137.4 GPa. Compared to those reported in previous experimental and DFT or semiempirical works, the present values for the zircon-type phase are comparable or slightly lower, whereas those for the scheelite-type phase are markedly lower. Discrepancies between the present results and earlier reported ones are attributed to differences in details of the experimental method such as the pressure transmitting medium and the pressure calibration method. The calculated band structure confirms that zircon-type EuVO{sub 4} is a direct-gap semiconductor, with a bandgap energy at zero pressure of 2.88 eV. Under compression, the bandgap of the zircon phase increases with a coefficient of 10.3 meV/GPa up to the transition pressure, at which point the present calculations show a small drop of the bandgap energy. Above the transition pressure, the bandgap energy of the scheelite phase becomes almost

  18. Equation of state and electronic properties of EuVO4: A high-pressure experimental and computational study

    International Nuclear Information System (INIS)

    Paszkowicz, Wojciech; López-Solano, Javier; Piszora, Paweł; Bojanowski, Bohdan; Mujica, Andrés; Muñoz, Alfonso; Cerenius, Yngve; Carlson, Stefan; Dąbkowska, Hanna

    2015-01-01

    Structural, elastic and electronic properties of zircon-type and scheelite-type EuVO 4 are investigated experimentally, by in-situ X-ray diffraction using synchrotron radiation, and theoretically within the framework of the density functional theory (DFT) and using the PBE prescription of the exchange-correlation energy. This study was motivated by the fact that the previous knowledge of the equation of state (EOS) was inconclusive due to a large scatter of the experimental and theoretical data, and by the lack of information on the dependence of the electronic structure with pressure. Under the applied experimental conditions, the zircon-type structure transforms to a scheelite-type one at 7.4(2) GPa, whereas the calculations yield a lower zircon–scheelite-coexistence pressure of 4.8 GPa. The experimental part of the study shows that the bulk modulus of the zircon-type phase is 119(3) GPa, perfectly supported by the DFT-calculated value, 119.1 GPa. The bulk modulus for the scheelite-type polymorph is higher, with an experimental value of 135(7) GPa and a theoretical one of 137.4 GPa. Compared to those reported in previous experimental and DFT or semiempirical works, the present values for the zircon-type phase are comparable or slightly lower, whereas those for the scheelite-type phase are markedly lower. Discrepancies between the present results and earlier reported ones are attributed to differences in details of the experimental method such as the pressure transmitting medium and the pressure calibration method. The calculated band structure confirms that zircon-type EuVO 4 is a direct-gap semiconductor, with a bandgap energy at zero pressure of 2.88 eV. Under compression, the bandgap of the zircon phase increases with a coefficient of 10.3 meV/GPa up to the transition pressure, at which point the present calculations show a small drop of the bandgap energy. Above the transition pressure, the bandgap energy of the scheelite phase becomes almost constant, with

  19. High pressure processing of meat

    DEFF Research Database (Denmark)

    Grossi, Alberto; Christensen, Mette; Ertbjerg, Per

    Abstract Background: The research of high pressure (HP) processing of meat based foods needs to address how pressure affects protein interactions, aggregation and/or gelation. The understanding of the gel forming properties of myofibrillar components is fundamental for the development of muscle...... based products (Chapleau et al., 2004;Colmenero, 2002). Object: The aim was to study the rheological properties of pork meat emulsion exposed to HP and the effect of HP on the aggregation state of myofibrillar proteins. To address the role of cathepsin in myofibrillar protein degradation the changes...... in the myofibrillar protein pattern and HP-induced change in activity of cathepsin B and L were investigated. Results: In this study we showed that HP treatment of pork meat emulsion, ranging from 0.1 to 800 MPa, induced protein gel formation as shown by the increased Young’s modulus (Fig.1). Analysis of SDS...

  20. Neutron Diffraction Study of Structural Phase Transition in Ternary Mercury Chalcogenides $HgSe_{1-x}S_{x}$ under High Pressure

    CERN Document Server

    Voronin, V I; Berger, I F; Glazkov, V P; Kozlenko, D P; Savenko, B N; Tikhomirov, S V

    2001-01-01

    A structure of ternary mercury chalcogenides HgSe_{1-x}S_x has been studied by means of neutron diffraction under high pressure up to 35 kbar. A phase transition from the cubic zinc blende phase to the hexagonal cinnabar phase was observed with the pressure increase. Lattice parameters and positional parameters of Hg and Se/S atoms as functions of pressure were obtained. Coexistence of the cubic and the hexagonal phases was observed in the pressure region close to the phase transition point.

  1. Raman scattering and x-ray diffraction studies of polycrystalline CaCu3Ti4O12 under high-pressure

    DEFF Research Database (Denmark)

    Valim, D.; Filho, A. G. S.; Freire, P. T. C.

    2004-01-01

    remains stable up to the maximum pressure (5.3 GPa) we reached in this experiment. The pressure coefficients for the observed Raman modes were determined. This set of parameters was used for evaluating the stress developed in CCTO thin films. The high-pressure x-ray studies were extended up to 46 GPa...... and the data confirmed that the T-h structure remains stable up to this pressure. The pressure-volume data are well described by the Birch's equation of state. The experimental value of the zero pressure bulk modulus is B-0=212+/-2 GPa. Gruneisen parameters of CCTO were also determined....

  2. High Pressure Industrial Water Facility

    Science.gov (United States)

    1992-01-01

    In conjunction with Space Shuttle Main Engine testing at Stennis, the Nordberg Water Pumps at the High Pressure Industrial Water Facility provide water for cooling the flame deflectors at the test stands during test firings.

  3. Solid-state amorphization of a quenched high-pressure GaSb phase studied by real-time neutron diffraction: evolution of the crystalline phase.

    Science.gov (United States)

    Fedotov, V K; Barkalov, O I; Ponyatovsky, E G; Calvo-Dahlborg, M; Dahlborg, U; Hansen, T

    2009-01-28

    The amorphization of a quenched sample of the GaSb-II high-pressure phase was studied at ambient pressure by real-time neutron diffraction in the course of the sample heating from 100 K to room temperature at a rate of 0.4 K min(-1). The transformation to the amorphous state begins at 140 K and is completed near room temperature. The β-Sn type structure was shown to represent only the mean lattice of the high-pressure GaSb-II phase. The superstructure of this phase widely varied with temperature and is caused by the ordered displacement of atoms. The temperature range of the metastable crystalline phase relaxation is divided into three intervals according to the temperature dependence of the tetragonality ratio (c/a). At the boundaries of these temperature intervals, i.e. temperatures T = 170 and 230 K, two second-order phase transitions are observed. Anomalous heat and volumetric effects were observed earlier by means of calorimetry and dilatometry in the same temperature range. Variation of the β-Sn type crystal structure reflects the general tendency of ideal tetrahedral bond network recovery. All phase transformations observed were found to be irreversible.

  4. A comparative in vitro study of the digestibility of heat- and high pressure-induced gels prepared from industrial milk whey proteins

    Science.gov (United States)

    He, Jin-Song; Mu, Tai-Hua; Wang, Juan

    2013-06-01

    We undertook this study to compare the digestibility of heat- and high pressure-induced gels produced from whey protein isolate (WPI). To simulate in vivo gastrointestinal digestion of WPI gels, a pepsin-trypsin digestion system was used. The in vitro protein digestibility of WPI gels induced by high pressure (400 MPa and 30 min; P-gel) and those induced by heat (80°C and 30 min; H-gel) was compared using a protein concentration of 0.14 g mL-1. The in vitro protein digestibility of P-gels was significantly greater than that of H-gels (p<0.05). The size-exclusion chromatography profiles of the hydrolysates showed that the P-gel generated more and smaller peptides than natural WPI and H-gels. Furthermore, Sodium dodecyl sulfate-polyacrylamide gel electrophoresis analysis showed some soluble disulfide-mediated aggregation in the P-gel, while there was more insoluble aggregation in the H-gel than the P-gel. The P-gel was more sensitive to proteinase than the H-gel, which was related to the content of S-S bonds, and this in turn could be attributed to the differences in the gelation mechanism between the H-gel and P-gel.

  5. Low-temperature single crystal X-ray diffraction and high-pressure Raman studies on [(CH 3) 2NH 2] 2[SbCl 5

    Science.gov (United States)

    Bujak, Maciej; Angel, Ross J.

    2007-11-01

    The structure of bis(dimethylammonium) pentachloroantimonate(III), [(CH 3) 2NH 2] 2[SbCl 5], BDP, was studied at 15 K and ambient pressure by single-crystal X-ray diffraction as well as at ambient temperature and high pressures up to 4.87(5) GPa by Raman spectroscopy. BDP crystallizes in the orthorhombic Pnma space group with a=8.4069(4), b=11.7973(7), c=14.8496(7) Å, and Z=4; R1=0.0381, w R2=0.0764. The structure consists of distorted [SbCl 6] 3- octahedra forming zig-zag [{SbCl 5} n] 2 n- chains that are cross-linked by dimethylammonium [(CH 3) 2NH 2] + cations. The organic and inorganic substructures are bound together by the N-H…Cl hydrogen bonds. The distortions of [SbCl 6] 3- units increase, partly due to the influence of the hydrogen bonds which became stronger, with decreasing temperature. The preliminary room temperature, high-pressure X-ray diffraction experiments suggest that BDP undergoes a first-order phase transition below ca. 0.44(5) GPa that destroys single-crystal samples. The transition is accompanied by changes in the intensities and positions of the Raman lines below 400 cm -1.

  6. High Pressure Spectroscopic Studies of AlGaAs, GaAs, and II-VI Semiconductors and Heterostructures

    National Research Council Canada - National Science Library

    Chandrasekhar, Meera

    1997-01-01

    We have conducted four studies on three different but related materials. The first is a temperature study of a pseudomorphic epilayer of ZnSe on GaAs, where we measured the temperature dependence of the interlayer biaxial strain...

  7. High-pressure studies of superconductivity in BiO0. 75F0. 25BiS2

    Indian Academy of Sciences (India)

    ). We have investigated the effect of pressure on magnetization measurements. Our studies suggest improved superconducting properties in polycrystalline samples of BiO 0.75 F 0.25 BiS 2 . The Tc in our sample is 5.3 K, at ambient pressure, ...

  8. Pulsed laser kinetic studies of liquids under high pressure. Progress report, November 25, 1991--September 18, 1992

    Energy Technology Data Exchange (ETDEWEB)

    Eyring, E.M.

    1992-09-22

    A laser flash photolysis kinetic study of 2,2{prime}-bipyridine bidentate chelating ligands with one claw in the first coordination sphere of a molybdenum carbonyl complex has been completed at pressures up to 150 MPa. The reaction mechanism for thermal ring closure is found from activation volumes to change from associative interchange to dissociative interchange as substituents on the 2,2{prime}-bipyridine ligands become bulkier. In a similar study of more rigid, substituted phenanthroline bidentate ligands it was found that substituent bulkiness had little effect on the thermal ring closure mechanism. Stability constants for lithium ion complexes with crown ethers in a room temperature molten salt, fluorescence quantum yields for cresyl violet and several other dyes in solution, and the oxidation of alcohols by OsO{sub 4} have also been investigated.

  9. Transmission electron microscopy studies of C3N4H4 treated at high pressure and high temperature

    International Nuclear Information System (INIS)

    Yu, R C; Chen, L C; Zhu, J L; Li, F Y; Liu, Z X; Qin, Z C; Yu, T N; Jin, C Q; Duan, X F; Zhang, Z

    2002-01-01

    C 3 N 4 H 4 was treated at 6.0 GPa and 1500 deg C for 2.5 min. Powder x-ray measurement shows that the sample is decomposed and a hexagonal graphite phase forms. Transmission electron microscopy studies show that small amounts of diamond and amorphous carbon phase coexist with the graphite phase. Parallel electron energy-loss spectroscopy analysis was also carried out for these phases

  10. High-pressure optical spectroscopy and X-ray diffraction studies on synthetic cobalt aluminum silicate garnet

    DEFF Research Database (Denmark)

    N. Taran, Michail; Nestola, Fabrizio; Ohashi, Haruo

    2007-01-01

    The pressure-induced behavior of spin-allowed dd-bands of VIIICo2+ in the absorption spectra of synthetic Co3Al2Si3O12 garnet was studied from 10-4 to 13 GPa. The plots of the peak energy vs. pressure for the three sharpest well resolved bands at ca. 5160, 17 680, and 18 740 cm-1 display small bu...

  11. Laser techniques in high-pressure geophysics

    Science.gov (United States)

    Hemley, R. J.; Bell, P. M.; Mao, H. K.

    1987-01-01

    Laser techniques in conjunction with the diamond-anvil cell can be used to study high-pressure properties of materials important to a wide range of problems in earth and planetary science. Spontaneous Raman scattering of crystalline and amorphous solids at high pressure demonstrates that dramatic changes in structure and bonding occur on compression. High-pressure Brillouin scattering is sensitive to the pressure variations of single-crystal elastic moduli and acoustic velocities. Laser heating techniques with the diamond-anvil cell can be used to study phase transitions, including melting, under deep-earth conditions. Finally, laser-induced ruby fluorescence has been essential for the development of techniques for generating the maximum pressures now possible with the diamond-anvil cell, and currently provides a calibrated in situ measure of pressure well above 100 gigapascals.

  12. A numerical study of the gas-liquid, two-phase flow maldistribution in the anode of a high pressure PEM water electrolysis cell

    DEFF Research Database (Denmark)

    Olesen, Anders Christian; Rømer, Carsten; Kær, Søren Knudsen

    2016-01-01

    In this work, the use of a circular-planar, interdigitated flow field for the anode of a high pressure proton exchange membrane (PEM) water electrolysis cell is investigated in a numerical study. While PEM fuel cells have separated flow fields for reactant transport and coolant, it is possible......-phase flow model for establishing the effect of geometry and a two-phase flow model for studying the effect of dispersed gas bubbles. Both models account for turbulence and heat transport. By means of the developed models, it is elucidated that the circular-planar shape of the interdigitated flow field...... causes maldistribution, if land areas of equal width are applied. Moreover, below a water stoichiometry of 350, and at a current density of 1 A/cm2, flow and temperature maldistribution is adversely affected by the presence of the gas phase; particularly gas hold-up near outlet channels can cause...

  13. High-pressure optical spectroscopy and X-ray diffraction studies on synthetic cobalt aluminum silicate garnet

    DEFF Research Database (Denmark)

    N. Taran, Michail; Nestola, Fabrizio; Ohashi, Haruo

    2007-01-01

    The pressure-induced behavior of spin-allowed dd-bands of VIIICo2+ in the absorption spectra of synthetic Co3Al2Si3O12 garnet was studied from 10-4 to 13 GPa. The plots of the peak energy vs. pressure for the three sharpest well resolved bands at ca. 5160, 17 680, and 18 740 cm-1 display small...... but discernible breaks in linear relations between 4 and 5 GPa. Datafromsingle-crystalX-raydiffractionData from single-crystal X-ray diffraction likewise show discontinuities in trends of CoO8 polyhedral volume and distortion, and Co-O and Si-O bond distances over this pressure range. These effects are related...

  14. Study of vibrational spectra of NH sub 4 Cl and NH sub 4 Br at high pressure

    CERN Document Server

    Glazkov, V P; Syrykh, G F; Kozlenko, D P; Savenko, B N; Telepnev, A S

    2002-01-01

    The NH sub 4 Cl vibrational spectra at the pressures up to 2.6 GPa and the NH sub 4 Br spectra at the pressures up to 7 GPa are studied through the method of the neutrons inelastic incoherent scattering. It is established that the linear baric dependence of the libration mode changes its inclination in the area above the pressure of transition from the disordered cubic phase to the ordered cubic phase with the CsCl-type structure. The baric dependence inclination of the cross-sectional optical translation mode remains unchanged. The evaluations of the Grueneisen parameters are presented in the one-dimensional approximation and the form of the potential function for the libration oscillations in the disordered and ordered cubic phases with the CsCl-type structure is calculated. It is shown that the observed effects are related to the high anharmonism of the potential in the disordered phase

  15. Injection characteristics study of high-pressure direct injector for Compressed Natural Gas (CNG) using experimental and analytical method

    Science.gov (United States)

    Taha, Z.; Rahim, MF Abdul; Mamat, R.

    2017-10-01

    The injection characteristics of direct injector affect the mixture formation and combustion processes. In addition, the injector is converted from gasoline operation for CNG application. Thus measurement of CNG direct injector mass flow rate was done by independently tested a single injector on a test bench. The first case investigated the effect of CNG injection pressure and the second case evaluate the effect of pulse-width of injection duration. An analytical model was also developed to predict the mass flow rate of the injector. The injector was operated in a choked condition in both the experiments and simulation studies. In case 1, it was shown that mass flow rate through the injector is affected by injection pressure linearly. Based on the tested injection pressure of 20 bar to 60 bar, the resultant mass flow rate are in the range of 0.4 g/s to 1.2 g/s which are met with theoretical flow rate required by the engine. However, in Case 2, it was demonstrated that the average mass flow rate at short injection durations is lower than recorded in Case 1. At injection pressure of 50 bar, the average mass flow rate for Case 2 and Case 1 are 0.7 g/s and 1.1 g/s respectively. Also, the measured mass flow rate at short injection duration showing a fluctuating data in the range of 0.2 g/s - 1.3 g/s without any noticeable trends. The injector model able to predict the trend of the mass flow rate at different injection pressure but unable to track the fluctuating trend at short injection duration.

  16. High-pressure structural study of fluoro-perovskite CsCdF3 up to 60 GPa: A combined experimental and theoretical study

    DEFF Research Database (Denmark)

    Vaitheeswaran, G.; Kanchana, V.; Kumar, Ravhi S.

    2010-01-01

    The structural behavior of CsCdF3 under pressure is investigated by means of theory and experiment. High-pressure powder x-ray diffraction experiments were performed up to a maximum pressure of 60 GPa using synchrotron radiation. The cubic Pm3̅ m crystal symmetry persists throughout this pressure...

  17. Frozen-in vacancies in PVD-Cu films with improved high-pressure reflowability studied using a slow positron beam

    International Nuclear Information System (INIS)

    Yabuuchi, A; Kubo, D; Mizuno, M; Araki, H; Onishi, T; Shirai, Y

    2009-01-01

    Recently, a new process has been proposed for fabricating a LSI interconnection; filling trenches and via holes with Cu using high-pressure annealing treatment. It is already known that a Cu film produced by physical vapor deposition (PVD) has a lower reflowability compared to a Cu film produced by electrochemical deposition (ECD). Additionally, it has also been recognized that the addition of Sb to the PVD-Cu film improves the reflowability. However, the factors responsible for the reflowability of Cu films have not yet been studied. In this work, we evaluated a PVD pure-Cu film and a PVD Cu-0.5at%Sb film by using a slow positron beam. Addition of Sb led to the introduction of lattice defects in the as-deposited film. These defects that were observed in the PVD-CuSb dilute alloy film were identified as frozen-in vacancies that were produced during deposition.

  18. Structure, Mobility, and Composition of Transition Metal Catalyst Surfaces. High-Pressure Scanning Tunneling Microscopy and Ambient-Pressure X-ray Photoelectron Spectroscopy Studies

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Zhongwei [Univ. of California, Berkeley, CA (United States)

    2013-12-06

    Surface structure, mobility, and composition of transition metal catalysts were studied by high-pressure scanning tunneling microscopy (HP-STM) and ambient-pressure X-ray photoelectron spectroscopy (AP-XPS) at high gas pressures. HP-STM makes it possible to determine the atomic or molecular rearrangement at catalyst surfaces, particularly at the low-coordinated active surface sites. AP-XPS monitors changes in elemental composition and chemical states of catalysts in response to variations in gas environments. Stepped Pt and Cu single crystals, the hexagonally reconstructed Pt(100) single crystal, and Pt-based bimetallic nanoparticles with controlled size, shape and composition, were employed as the model catalysts for experiments in this thesis.

  19. Sintering of zirconia in high-pressure

    International Nuclear Information System (INIS)

    Kunrath, A.O.; Strohaecker, T.R.; Pereira, A.S.; Jornada, J.A.H. da; Piermarini, G.J.

    1989-01-01

    A systematic study about the sintering of zirconia hyperfines powders in high-pressure is presented. The differents conditions effect of sintering in microstructure and in hardness and tenacity properties of zirconia samples with a very fine grain is also studied. (C.G.C.) [pt

  20. Phase diagram of Nitrogen at high pressures and temperatures

    Science.gov (United States)

    Jenei, Zsolt; Lin, Jung-Fu; Yoo, Choong-Shik

    2007-03-01

    Nitrogen is a typical molecular solid with relatively weak van der Waals intermolecular interactions but strong intramolecular interaction arising from the second highest binding energy of all diatomic molecules. The phase diagram of solid nitrogen is, however, complicated at high pressures, as inter-molecular interaction becomes comparable to the intra-molecular interaction. In this paper, we present an updated phase diagram of the nitrogen in the pressure-temperature region of 100 GPa and 1000 K, based on in-situ Raman and synchrotron x-ray diffraction studies using externally heated membrane diamond anvil cells. While providing an extension of the phase diagram, our results indicate a ``steeper'' slope of the δ/ɛ phase boundary than previously determined^1. We also studied the stability of the ɛ phase at high pressures and temperatures. Our new experimental results improve the understanding of the Nitrogen phase diagram. 1. Gregoryanz et al, Phys. Rev. B 66, 224108 (2002)

  1. High pressure elasticity and thermal properties of depleted uranium

    International Nuclear Information System (INIS)

    Jacobsen, M. K.; Velisavljevic, N.

    2016-01-01

    Studies of the phase diagram of uranium have revealed a wealth of high pressure and temperature phases. Under ambient conditions the crystal structure is well defined up to 100 gigapascals (GPa), but very little information on thermal conduction or elasticity is available over this same range. This work has applied ultrasonic interferometry to determine the elasticity, mechanical, and thermal properties of depleted uranium to 4.5 GPa. Results show general strengthening with applied load, including an overall increase in acoustic thermal conductivity. Further implications are discussed within. This work presents the first high pressure studies of the elasticity and thermal properties of depleted uranium metal and the first real-world application of a previously developed containment system for making such measurements.

  2. High-pressure water facility

    Science.gov (United States)

    2006-01-01

    NASA Test Operations Group employees, from left, Todd Pearson, Tim Delcuze and Rodney Wilkinson maintain a water pump in Stennis Space Center's high-pressure water facility. The three were part of a group of employees who rode out Hurricane Katrina at the facility and helped protect NASA's rocket engine test complex.

  3. Radon anomalies prior to earthquakes (1). Review of previous studies

    International Nuclear Information System (INIS)

    Ishikawa, Tetsuo; Tokonami, Shinji; Yasuoka, Yumi; Shinogi, Masaki; Nagahama, Hiroyuki; Omori, Yasutaka; Kawada, Yusuke

    2008-01-01

    The relationship between radon anomalies and earthquakes has been studied for more than 30 years. However, most of the studies dealt with radon in soil gas or in groundwater. Before the 1995 Hyogoken-Nanbu earthquake, an anomalous increase of atmospheric radon was observed at Kobe Pharmaceutical University. The increase was well fitted with a mathematical model related to earthquake fault dynamics. This paper reports the significance of this observation, reviewing previous studies on radon anomaly before earthquakes. Groundwater/soil radon measurements for earthquake prediction began in 1970's in Japan as well as foreign countries. One of the most famous studies in Japan is groundwater radon anomaly before the 1978 Izu-Oshima-kinkai earthquake. We have recognized the significance of radon in earthquake prediction research, but recently its limitation was also pointed out. Some researchers are looking for a better indicator for precursors; simultaneous measurements of radon and other gases are new trials in recent studies. Contrary to soil/groundwater radon, we have not paid much attention to atmospheric radon before earthquakes. However, it might be possible to detect precursors in atmospheric radon before a large earthquake. In the next issues, we will discuss the details of the anomalous atmospheric radon data observed before the Hyogoken-Nanbu earthquake. (author)

  4. High-pressure differential scanning microcalorimeter.

    Science.gov (United States)

    Senin, A A; Dzhavadov, L N; Potekhin, S A

    2016-03-01

    A differential scanning microcalorimeter for studying thermotropic conformational transitions of biopolymers at high pressure has been designed. The calorimeter allows taking measurements of partial heat capacity of biopolymer solutions vs. temperature at pressures up to 3000 atm. The principles of operation of the device, methods of its calibration, as well as possible applications are discussed.

  5. Relationship Between Far Field Stresses, Fluid Flow and High-Pressure Deserpentinization in Subducting Slabs: a Case Study From the Almirez Ultramafic Massif

    Science.gov (United States)

    Dilissen, Nicole; Hidas, Károly; Garrido, Carlos J.; López Sánchez-Vizcaíno, Vicente; Kahl, Wolf-Achim; Padrón-Navarta, José Alberto; Jesús Román-Alpiste, Manuel

    2017-04-01

    Serpentinite dehydration during prograde metamorphism plays a crucial role in subduction dynamics. Observations from exhumed paleo-subduction metamorphic terranes suggest that the discharge of deserpentinization fluids from the subducting slab takes place along different pathways and mechanisms [e.g. 1-3]. Analysis of intermediate-depth focal solutions in active subduction zones indicates that slabs are subjected to different principal stress fields characterized primarily by downdip compression and downdip tension [4]. Although it is well known that far field stresses play a crucial role on fluid flow channeling, their potential impact on the kinetics of serpentinite dehydration and subsequent fluid escape in subducting slabs is still poorly understood. Here, we present a detailed structural and microstructural study to investigate the relationships between far field stresses, fluid flow and high-pressure deserpentinization in the Almirez ultramafic massif (Betic Cordillera, SE Spain) [1, 2]. This massif preserves the high-pressure breakdown of antigorite (Atg-) serpentinite to prograde chlorite (Chl-) harzburgite, which are separated by a sharp isograd [2, 5]. The Chl-harzburgite reaction products show either a granofels or spinifex-like texture indicating crystallization under different overstepping of the Atg-out reaction. The two different textural types of Chl-harzburgite occur below the Atg-out isograd as alternating, meter-wide lenses with either a granofels or spinifex texture. From field measurements, we infer that during antigorite dehydration the minimum compressive stress was subnormal to the dehydration front and the paleo-slab surface. This stress field is consistent with subduction zones with slabs under downdip compression at intermediate depths [4]. The detailed microstructural study —combining µ-CT and EBSD-SEM [6]— of Chl-harzburgite across a c. 15 m wide lens reveals that the SPO and CPO of olivines with contrasting textures are strongly

  6. High pressure and high temperature in situ X-ray diffraction studies in the Paris-Edinburgh cell using a laboratory X-ray source†

    Science.gov (United States)

    Toulemonde, Pierre; Goujon, Céline; Laversenne, Laetitia; Bordet, Pierre; Bruyère, Rémy; Legendre, Murielle; Leynaud, Olivier; Prat, Alain; Mezouar, Mohamed

    2014-04-01

    We have developed a new laboratory experimental set-up to study in situ the pressure-temperature phase diagram of a given pure element or compound, its associated phase transitions, or the chemical reactions involved at high pressure and high temperature (HP-HT) between different solids and liquids. This new tool allows laboratory studies before conducting further detailed experiments using more brilliant synchrotron X-ray sources or before kinetic studies. This device uses the diffraction of X-rays produced by a quasi-monochromatic micro-beam source operating at the silver radiation (λ(Ag)Kα 1, 2≈0.56 Å). The experimental set-up is based on a VX Paris-Edinburgh cell equipped with tungsten carbide or sintered diamond anvils and uses standard B-epoxy 5 or 7 mm gaskets. The diffracted signal coming from the compressed (and heated) sample is collected on an image plate. The pressure and temperature calibrations were performed by diffraction, using conventional calibrants (BN, NaCl and MgO) for determination of the pressure, and by crossing isochores of BN, NaCl, Cu or Au for the determination of the temperature. The first examples of studies performed with this new laboratory set-up are presented in the article: determination of the melting point of germanium and magnesium under HP-HT, synthesis of MgB2 or C-diamond and partial study of the P, T phase diagram of MgH2.

  7. Intermolecular Interactions at high pressure

    DEFF Research Database (Denmark)

    Eikeland, Espen Zink

    2016-01-01

    transmitting medium. Through careful structural analysis combined with theoretical calculations, the structures of all the new high-pressure phases identified herein were determined. In the hydroquinone - methanol and hydroquinone - acetonitrile clathrate structures the phase transitions break the host...... illustrates how important it is to quantify all intermolecular interactions in structures. This enables researchers to see a more complete picture and not focus only on a few interactions deemed particularly important....

  8. Cobalt ferrite nanoparticles under high pressure

    Energy Technology Data Exchange (ETDEWEB)

    Saccone, F. D.; Ferrari, S.; Grinblat, F.; Bilovol, V. [Instituto de Tecnologías y Ciencias de la Ingeniería, “Ing. H. Fernández Long,” Av. Paseo Colón 850 (1063), Buenos Aires (Argentina); Errandonea, D., E-mail: daniel.errandonea@uv.es [Departamento de Fisica Aplicada, Institut Universitari de Ciència dels Materials, Universitat de Valencia, c/ Doctor Moliner 50, E-46100 Burjassot, Valencia (Spain); Agouram, S. [Departamento de Física Aplicada y Electromagnetismo, Universitat de València, 46100 Burjassot, Valencia (Spain)

    2015-08-21

    We report by the first time a high pressure X-ray diffraction and Raman spectroscopy study of cobalt ferrite (CoFe{sub 2}O{sub 4}) nanoparticles carried out at room temperature up to 17 GPa. In contrast with previous studies of nanoparticles, which proposed the transition pressure to be reduced from 20–27 GPa to 7.5–12.5 GPa (depending on particle size), we found that cobalt ferrite nanoparticles remain in the spinel structure up to the highest pressure covered by our experiments. In addition, we report the pressure dependence of the unit-cell parameter and Raman modes of the studied sample. We found that under quasi-hydrostatic conditions, the bulk modulus of the nanoparticles (B{sub 0} = 204 GPa) is considerably larger than the value previously reported for bulk CoFe{sub 2}O{sub 4} (B{sub 0} = 172 GPa). In addition, when the pressure medium becomes non-hydrostatic and deviatoric stresses affect the experiments, there is a noticeable decrease of the compressibility of the studied sample (B{sub 0} = 284 GPa). After decompression, the cobalt ferrite lattice parameter does not revert to its initial value, evidencing a unit cell contraction after pressure was removed. Finally, Raman spectroscopy provides information on the pressure dependence of all Raman-active modes and evidences that cation inversion is enhanced by pressure under non-hydrostatic conditions, being this effect not fully reversible.

  9. Microbiological stabilization of tiger nuts' milk beverage using ultra-high pressure homogenization. A preliminary study on microbial shelf-life extension.

    Science.gov (United States)

    Codina-Torrella, I; Guamis, B; Zamora, A; Quevedo, J M; Trujillo, A J

    2018-02-01

    Tiger nuts' milk beverages are highly perishable products. For this reason, the interest of food industry for their commercialization makes necessary the application of preservation treatments to prolong their shelf-life. In the current study, the effect of ultra-high pressure homogenization (UHPH) on the microbiological and sensory qualities of tiger nuts' milk beverage was evaluated. Characteristics of UHPH-treated products (at 200 and 300 MPa, with inlet temperature of 40 °C) were compared with those of raw (RP) and conventionally homogenized-pasteurized (H-P) beverages, after treatment and during cold storage at 4 °C. Microbiological quality of beverages was studied by enumerating total counts, psychrotrophic bacteria, lactobacilli, enterobacteria, molds and yeasts, and mesophilic spores. Evolution of color and sensory characteristics of beverages were also determined. Microbiological shelf-life of the tiger nuts' milk beverages was extended from 3 to 25, 30 and 57 days by applying H-P and UHPH treatments at 200 and 300 MPa, respectively. Color of beverages was the only attribute that differentiated UHPH samples from the others, with greater luminosity and whiteness. Hence, UHPH treatments showed to be an alternative to the conventional H-P for obtaining tiger nuts' milk beverages with an improved microbiological shelf-life and good sensorial characteristics. Copyright © 2017 Elsevier Ltd. All rights reserved.

  10. Design and fabrication of some special equipment for a high pressure high temperature facility for thermal hydraulic studies (Paper No. 10)

    International Nuclear Information System (INIS)

    Venkat Raj, V.; Dhall, H.C.; Markandeya, S.G.; Shendre, D.N.

    1987-02-01

    A thorough understanding of the various thermal hydraulic phenomena occurring in the reactor core and associated systems is essential for the design as well as safety analysis of nuclear power plants. While considerable progress has been made in the development of analytical tools for reactor design, still a lot of information related to both normal operation as well as safety of reactor systems is required to be generated experimentally. Moreover, experimental data also need to be generated for validating the analytical models and the computer codes developed for analysis. In order to perform experiments under stimulated operating conditions as in the actual systems, it is essential to have high temperature, high pressure facilities for experimental studies. The 3 MW Boiling Water Loop (BWL) has been set up to facilitate generation of experimental data relevant to design and safety analysis of PHWRs. The facility can be used to simulate parameters such as pressure, temperature, flow, etc. as in the actual reactor operating conditions. The facility has various equipment which have been designed to cater to a wide variation in operating parameters. Some of these such as pre-heater, super-heaters, etc. involved special design, fabrication and installation techniques, which are described and discussed in this paper. (author). 3 figs

  11. Analysis of Porous Structure Parameters of Biomass Chars Versus Bituminous Coal and Lignite Carbonized at High Pressure and Temperature—A Chemometric Study

    Directory of Open Access Journals (Sweden)

    Adam Smoliński

    2017-09-01

    Full Text Available The characteristics of the porous structure of carbonized materials affect their physical properties, such as density or strength, their sorption capacity, and their reactivity in thermochemical processing, determining both their applicability as fuels or sorbents and their efficiency in various processes. The porous structure of chars is shaped by the combined effects of physical and chemical properties of a carbonaceous material and the operating parameters applied in the carbonization process. In the study presented, the experimental dataset covering parameters of various fuels, ranging from biomass through lignite to bituminous coal, and chars produced at 1273 K and under the pressure of 1, 2, 3, and 4 MPa was analyzed with the application of the advanced method of data exploration. The principal component analysis showed that the sample of the highest coal rank was characterized by lower values of parameters reflecting the development of the porous structure of chars. A negative correlation was also observed between the carbon content in a fuel and the evolution of the porous structure of chars at high pressure. The highest total pore volume of chars produced under 1 and 3 MPa and the highest micropore surface area under 3 MPa were reported for a carbonized fuel sample of the highest moisture content.

  12. Study of electrical conductivity response upon formation of ice and gas hydrates from salt solutions by a second generation high pressure electrical conductivity probe

    Science.gov (United States)

    Sowa, Barbara; Zhang, Xue Hua; Kozielski, Karen A.; Dunstan, Dave E.; Hartley, Patrick G.; Maeda, Nobuo

    2014-11-01

    We recently reported the development of a high pressure electrical conductivity probe (HP-ECP) for experimental studies of formation of gas hydrates from electrolytes. The onset of the formation of methane-propane mixed gas hydrate from salt solutions was marked by a temporary upward spike in the electrical conductivity. To further understand hydrate formation a second generation of window-less HP-ECP (MkII), which has a much smaller heat capacity than the earlier version and allows access to faster cooling rates, has been constructed. Using the HP-ECP (MkII) the electrical conductivity signal responses of NaCl solutions upon the formation of ice, tetrahydrofuran hydrates, and methane-propane mixed gas hydrate has been measured. The concentration range of the NaCl solutions was from 1 mM to 3M and the driving AC frequency range was from 25 Hz to 5 kHz. This data has been used to construct an "electrical conductivity response phase diagrams" that summarize the electrical conductivity response signal upon solid formation in these systems. The general trend is that gas hydrate formation is marked by an upward spike in the conductivity at high concentrations and by a drop at low concentrations. This work shows that HP-ECP can be applied in automated measurements of hydrate formation probability distributions of optically opaque samples using the conductivity response signals as a trigger.

  13. Functional Sub-states by High-pressure Macromolecular Crystallography.

    Science.gov (United States)

    Dhaussy, Anne-Claire; Girard, Eric

    2015-01-01

    At the molecular level, high-pressure perturbation is of particular interest for biological studies as it allows trapping conformational substates. Moreover, within the context of high-pressure adaptation of deep-sea organisms, it allows to decipher the molecular determinants of piezophily. To provide an accurate description of structural changes produced by pressure in a macromolecular system, developments have been made to adapt macromolecular crystallography to high-pressure studies. The present chapter is an overview of results obtained so far using high-pressure macromolecular techniques, from nucleic acids to virus capsid through monomeric as well as multimeric proteins.

  14. High pressure stability analysis and chemical bonding of Ti{sub 1-x}Zr{sub x}N alloy: A first principle study

    Energy Technology Data Exchange (ETDEWEB)

    Chauhan, Mamta; Gupta, Dinesh C., E-mail: sosfizix@gmail.com, E-mail: mamta-physics@yahoo.co.in [Condensed Matter Theory Group, School of Studies in Physics, Jiwaji University, Gwalior – 474 011 (India)

    2016-05-23

    First-principles pseudo-potential calculations have been performed to analyze the stability of Ti{sub 1-x}Zr{sub x}N alloy under high pressures. The first order phase transition from B1 to B2 phase has been observed in this alloy at high pressure. The variation of lattice parameter with the change in concentration of Zr atom in Ti{sub 1-x}Zr{sub x}N is also reported in both the phases. The calculations for density of states have been performed to understand the alloying effects on chemical bonding of Ti-Zr-N alloy.

  15. Sum frequency generation vibrational spectroscopy studies of adsorbates on Pt(111): Studies of CO at high pressures and temperatures, coadsorbed with olefins and its role as a poison in ethylene hydrogenation

    Energy Technology Data Exchange (ETDEWEB)

    Kung, Kyle Yi [Univ. of California, Berkeley, CA (United States)

    2000-12-01

    High pressure high temperature CO adsorption and coadsorption with ethylene and propylene on Pt(111) was monitored in situ with infrared-visible sum frequency generation (SFG). At high pressures and high temperatures, CO dissociates on a Pt(111) surface to form carbon. At 400 torr CO pressure and 673K, CO modifies the Pt(111) surface through a carbonyl intermediate, and dissociates to leave carbon on the surface. SFG was used to follow the CO peak evolution from monolayer adsorption in ultra high vacuum (UHV) to 400 torr CO pressure. At this high pressure, a temperature dependence study from room temperature to 823K was carried out. Auger electron spectroscopy was used to identify carbon on the surface CO coadsorption with ethylene and CO coadsorption with propylene studies were carried out with 2-IR 1-visible SFG. With this setup, two spectral ranges covering the C-H stretch range and the CO stretch range can be monitored simultaneously. The coadsorption study with ethylene reveals that after 5L ethylene exposure on a Pt(111) surface to form ethylidyne , CO at high pressures cannot completely displace the ethylidyne from the surface. Instead, CO first adsorbs on defect sites at low pressures and then competes with ethylidyne for terrace sites at high pressures. Propylene coadsorption with CO at similar conditions shows that propylidyne undergoes conformation changes with increased CO pressure and at 1 torr, is absent from the Pt(111) surface. Experiments on CO poisoning of ethylene hydrogenation was carried by 2-IR 1-visible SFG. At 1 torr CO,10 torr ethylene and 100 torr hydrogen, CO was found to block active sites necessary for ethylene hydrogenation, Above 425K, CO desorbs from the surface to allow ethylene hydrogenation to occur. The gas phase species were monitored by gas chromatography.

  16. Hydrogen - High pressure production and storage

    International Nuclear Information System (INIS)

    Lauretta, J.R

    2005-01-01

    The development of simple, safe and more and more efficient technologies for the production and the storage of hydrogen is necessary condition for the transition towards the economy of hydrogen.In this work the hydrogen production studies experimentally to high pressure by electrolysis of alkaline solutions without the intervention of compressing systems and its direct storage in safe containers.The made tests show that the process of electrolysis to high pressure is feasible and has better yield than to low pressure, and that is possible to solve the operation problems, with relatively simple technology.The preliminary studies and tests indicate that the system container that studied is immune to the outbreak and can have forms and very different sizes, nevertheless, to reach or to surpass the efficiency of storage of the conventional systems the investments necessary will be due to make to be able to produce aluminum alloy tubes of high resistance

  17. High pressure effects in anaesthesia and narcosis.

    Science.gov (United States)

    Wlodarczyk, Agnieszka; McMillan, Paul F; Greenfield, Susan A

    2006-10-01

    There is growing interest in determining the effects of high pressure on biological functions. Studies of brain processes under hyperbaric conditions can give a unique insight into phenomena such as nitrogen narcosis, inert gas anaesthesia, and pressure reversal of the effects of anaesthetic and narcotic agents. Such research may shed light on the action of anaesthetics, which remains poorly understood, and on the nature of consciousness itself. Various studies have established the behavioural response of organisms to hyperbaric conditions, in the presence or absence of anaesthetic agents. At the molecular level, X-ray crystallography has been used to investigate the incorporation of species like Xe in hydrophobic pockets within model ion channels that may account for pressure effects on neuronal transmission. New magnetic resonance imaging techniques are providing tomographic three-dimensional images that detail brain structure and function, and that can be correlated with behavioural studies and psychological test results. Such whole organ techniques are linked to the molecular scale via voltage-sensitive dye (VSD) imaging studies on brain slices that provide time-resolved images of the dynamic formation and interconnection of inter-neuronal complexes. The VSD experiments are readily adapted to in situ studies under high pressure conditions. In this tutorial review we review the current state of knowledge of hyperbaric effects on brain processes: anaesthesia and narcosis, recent studies at the molecular level via protein crystallography at high pressure in a Xe atmosphere, and we also present some preliminary results of VSD imaging of brain slices under hyperbaric conditions.

  18. Magnetic and Superconducting Materials at High Pressures

    Energy Technology Data Exchange (ETDEWEB)

    Struzhkin, Viktor V. [Carnegie Inst. of Washington, Washington, DC (United States)

    2015-03-24

    The work concentrates on few important tasks in enabling techniques for search of superconducting compressed hydrogen compounds and pure hydrogen, investigation of mechanisms of high-Tc superconductivity, and exploring new superconducting materials. Along that route we performed several challenging tasks, including discovery of new forms of polyhydrides of alkali metal Na at very high pressures. These experiments help us to establish the experimental environment that will provide important information on the high-pressure properties of hydrogen-rich compounds. Our recent progress in RIXS measurements opens a whole field of strongly correlated 3d materials. We have developed a systematic approach to measure major electronic parameters, like Hubbard energy U, and charge transfer energy Δ, as function of pressure. This technique will enable also RIXS studies of magnetic excitations in iridates and other 5d materials at the L edge, which attract a lot of interest recently. We have developed new magnetic sensing technique based on optically detected magnetic resonance from NV centers in diamond. The technique can be applied to study superconductivity in high-TC materials, to search for magnetic transitions in strongly correlated and itinerant magnetic materials under pressure. Summary of Project Activities; development of high-pressure experimentation platform for exploration of new potential superconductors, metal polyhydrides (including newly discovered alkali metal polyhydrides), and already known superconductors at the limit of static high-pressure techniques; investigation of special classes of superconducting compounds (high-Tc superconductors, new superconducting materials), that may provide new fundamental knowledge and may prove important for application as high-temperature/high-critical parameter superconductors; investigation of the pressure dependence of superconductivity and magnetic/phase transformations in 3d transition metal compounds, including

  19. Inspection technology for high pressure pipes

    International Nuclear Information System (INIS)

    Kim, Jae H.; Lee, Jae C.; Eum, Heung S.; Choi, Yu R.; Moon, Soon S.; Jang, Jong H.

    2000-02-01

    Various kinds of defects are likely to be occurred in the welds of high pressure pipes in nuclear power plants. Considering the recent accident of Zuruga nuclear power plant in Japan, reasonable policy is strongly requested for the high pressure pipe integrity. In this study, we developed the technologies to inspect pipe welds automatically. After development of scanning robot prototype in the first research year, we developed and implemented the algorithm of automatic tracking of the scanning robot along the weld line of the pipes. We use laser slit beam on weld area and capture the image using digital camera. Through processing of the captures image, we finally determine the weld line automatically. In addition, we investigated a new technology on micro systems for developing micro scanning robotic inspection of the pipe welds. The technology developed in this study is being transferred to the industry. (author)

  20. New study reveals twice as many asteroids as previously believed

    Science.gov (United States)

    2002-05-01

    The ISO satellite Credits: ESA ISO An artist's impression of the ISO spacecraft. The ISO Deep Asteroid Search indicates that there are between 1.1 million and 1.9 million 'space rocks' larger than 1 kilometre in diameter in the so-called 'main asteroid belt', about twice as many as previously believed. However, astronomers think it is premature to revise current assessments of the risk of the Earth being hit by an asteroid. Despite being in our own Solar System, asteroids can be more difficult to study than very distant galaxies. With sizes of up to one thousand kilometres in diameter, the brightness of these rocky objects may vary considerably in just a few minutes. They move very quickly with respect to the stars - they have been dubbed 'vermin of the sky' because they often appear as trails on long exposure images. This elusiveness explains why their actual number and size distribution remains uncertain. Most of the almost 40,000 asteroids catalogued so far (1) orbit the Sun forming the 'main asteroid belt', between Mars and Jupiter, too far to pose any threat to Earth. However, space-watchers do keep a closer eye on another category of asteroids, the 'Near Earth Asteroids' or 'NEAs', which are those whose orbits cross, or are likely to cross, that of our planet. The ISO Deep Asteroid Search (IDAS), the first systematic search for these objects performed in infrared light, focused on main belt asteroids. Because it is impossible to simply point the telescope at the whole main belt and count, astronomers choose selected regions of the belt and then use a theoretical model to extrapolate the data to the whole belt. Edward Tedesco (TerraSystems, Inc., New Hampshire, United States) and François-Xavier Desert (Observatoire de Grenoble, France) observed their main belt selected areas in 1996 and 1997 with ESA's ISO. They found that in the middle region of the belt the density of asteroids was 160 asteroids larger than 1 kilometre per square degree - an area of the

  1. High-pressure cells for study of condensed matter by diffraction and inelastic neutron scattering at low temperatures and in strong magnetic fields

    Science.gov (United States)

    Sadykov, R. A.; Strassle, Th; Podlesnyak, A.; Keller, L.; Fak, B.; Mesot, J.

    2017-12-01

    We have developed and implemented series of new original clamp high-pressure cells for neutron diffraction and inelastic neutron scattering at low temperatures. The cells design allows one to place them in the standard cryostats or cryomagnets used on neutron sources. Some results obtained for ZnCr2Se4 are demonstrated as an example.

  2. Collapse of ferromagnetism in itinerant-electron system: a magnetic, transport properties, and high pressure study of (Hf,Ta)Fe.sub.2./sub. compounds

    Czech Academy of Sciences Publication Activity Database

    Diop, L.; Kaštil, Jiří; Isnard, O.; Arnold, Zdeněk; Kamarád, Jiří

    2014-01-01

    Roč. 116, č. 16 (2014), "163907-1"-"163907-10" ISSN 0021-8979 R&D Projects: GA ČR GAP204/12/0692 Institutional support: RVO:68378271 Keywords : high pressure * magnetic properties Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.183, year: 2014

  3. Structural study of Pr.sub.0.8./sub.Na.sub.0.2./sub.MnO.sub.3./sub. at high pressure

    Czech Academy of Sciences Publication Activity Database

    Kozlenko, D. P.; Glazkov, V. P.; Jirák, Zdeněk; Savenko, B. N.

    2003-01-01

    Roč. 267, - (2003), s. 120-126 ISSN 0304-8853 Institutional research plan: CEZ:AV0Z1010914 Keywords : manganites * high pressures * crystal and magnetic structure * neutron diffraction Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.910, year: 2003

  4. observed by high pressure NMR and NQR

    Indian Academy of Sciences (India)

    Department of Material Science, Himeji Institute of Technology, Kamigori,. Akogun, Hyogo 678-1297, Japan. ∗. Email: kohara@sci.himeji tech.ac.jp. Abstract. NMR and NQR studies on two interesting systems (URu2Si2, CeTIn5) were performed under high pressure. (1) URu2Si2: In the pressure range 3.0 to 8.3 kbar, we ...

  5. A computational study of syngas auto-ignition characteristics at high-pressure and low-temperature conditions with thermal inhomogeneities

    KAUST Repository

    Pal, Pinaki

    2015-07-30

    A computational study was conducted to investigate the characteristics of auto-ignition in a syngas mixture at high-pressure and low-temperature conditions in the presence of thermal inhomogeneities. Highly resolved one-dimensional numerical simulations incorporating detailed chemistry and transport were performed. The temperature inhomogeneities were represented by a global sinusoidal temperature profile and a local Gaussian temperature spike (hot spot). Reaction front speed and front Damköhler number analyses were employed to characterise the propagating ignition front. In the presence of a global temperature gradient, the ignition behaviour shifted from spontaneous propagation (strong) to deflagrative (weak), as the initial mean temperature of the reactant mixture was lowered. A predictive Zel\\'dovich–Sankaran criterion to determine the transition from strong to weak ignition was validated for different parametric sets. At sufficiently low temperatures, the strong ignition regime was recovered due to faster passive scalar dissipation of the imposed thermal fluctuations relative to the reaction timescale, which was quantified by the mixing Damköhler number. In the presence of local hot spots, only deflagrative fronts were observed. However, the fraction of the reactant mixture consumed by the propagating front was found to increase as the initial mean temperature was lowered, thereby leading to more enhanced compression-heating of the end-gas. Passive scalar mixing was not found to be important for the hot spot cases considered. The parametric study confirmed that the relative magnitude of the Sankaran number translates accurately to the quantitative strength of the deflagration front in the overall ignition advancement. © 2015 Taylor & Francis

  6. Foaming Glass Using High Pressure Sintering

    DEFF Research Database (Denmark)

    Østergaard, Martin Bonderup; Petersen, Rasmus Rosenlund; König, Jakob

    Foam glass is a high added value product which contributes to waste recycling and energy efficiency through heat insulation. The foaming can be initiated by a chemical or physical process. Chemical foaming with aid of a foaming agent is the dominant industrial process. Physical foaming has two...... variations. One way is by saturation of glass melts with gas. The other involves sintering of powdered glass under a high gas pressure resulting in glass pellets with high pressure bubbles entrapped. Reheating the glass pellets above the glass transition temperature under ambient pressure allows the bubbles...... to expand. After heat-treatment foam glass can be obtained with porosities of 80–90 %. In this study we conduct physical foaming of cathode ray tube (CRT) panel glass by sintering under high pressure (5-25 MPa) using helium, nitrogen, or argon at 640 °C (~108 Pa s). Reheating a sample in a heating...

  7. Volume and structural study of Fe{sub 64}Mn{sub 36} anti-ferromagnetic Invar alloy under high pressure

    Energy Technology Data Exchange (ETDEWEB)

    Matsushita, M., E-mail: matsushita@eng.ehime-u.ac.j [Department of Mechanical Engineering, Graduate School of Science and Engineering, Ehime University, 3-Bunkyocho, Matsuyama 790-0826 (Japan); Nakano, S. [National Institute for Materials Science, Tsukuba, Ibaraki 305-0044 (Japan); Ohfuji, H. [Geodynamics Research Center, Ehime University, 2-Bunkyocho, Matsuyama 790-0826 (Japan); Yamada, I. [Department of Chemistry and Biology, Graduate School of Science and Engineering, Ehime University, 2-Bunkyocho, Matsuyama 790-0826 (Japan); Kikegawa, T. [High Energy Accelerator Research Organization, Tsukuba 305-0801 (Japan)

    2011-03-15

    We have investigated the pressure variation of the volume and structure of an FCC Fe{sub 64}Mn{sub 36} anti-ferromagnetic Invar alloy. The inclination of the pressure-volume (P-V) curve of the FCC structure becomes discontinuous at a pressure of 4 GPa. According to the bulk modulus at zero pressure estimated by the Birch-Murnaghan equation of state, the pressure between 4 and 10 GPa is 33 GPa larger than that at a pressure below 4 GPa. Considering previous experiments on magnetism at high pressure the Neel temperature at 4 GPa almost decreases to room temperature. These results suggest that the increase in the bulk modulus by 33 GPa can be attributed to the pressure-induced magnetic phase transition from anti-ferromagnetism to paramagnetism. Volume at zero pressure was estimated using the Birch-Murnaghan equation of state. The volume of FCC structure in the anti-ferromagnetic state was 1.17% larger than the volume in the paramagnetic state, namely, the spontaneous magnetostriction was 1.17%. Pressure-induced structural transition from FCC to HCP occurs with an increase in the pressure, especially at up to 5 GPa. The value of c/a is 1.62; this value almost corresponds to that of an ideal HCP structure. The bulk modulus of the HCP structure estimated by the Birch-Murnaghan equation of state is larger than that of the FCC structure, and the volume/atom ratio is smaller than that of the FCC structure. - Research highlights: > We have investigated the pressure variation of volume and structure of FCC Fe{sub 64}Mn{sub 36} alloy. > We discovered that the change in inclination of the pressure-volume (P-V) curve of the FCC structure becomes discontinuous at a pressure of 4 GPa. This pressure corresponds to the Neel temperature, which decreases down to room temperature. > Further we estimated bulk modulus and volume at zero pressure using the Birch-Murnaghan equation of state. As a result, we have demonstrated that anti-ferromagnetism has very close relationship with the

  8. [Interest of a systematic second-look at 48-72 hours in high-pressure injections of paint: an animal study].

    Science.gov (United States)

    Chaput, B; Courtade-Saïdi, M; De Bonnecaze, G; Rongieres, M; Apredoaei, C; Grolleau, J-L; Garrido, I

    2012-08-01

    High-pressure injections (HPI) in the hand are rare and their prognosis is often tragic, some authors report up to 48% of amputations. Poorly standardized, their management is often too late and inadequate. The HPI of paint results in inoculation of toxic particles in depth that are particularly difficult to remove surgically. The persistence of this foreign material maintains local inflammation and increases the risk of infection. We wanted to simulate in rats, the physiopathology of HPI with paint. The aim of this study is to authenticate an advantage to achieve consistently a second surgical debridement at 48-72 hours in HPI with paint. Six rats were injected with 200 bars of white glycerophtalic paint in the leg. At six hours and then every 24 hours for four days, we did a debridement and a surgical washing, then at the end of intervention a tissue sample was analyzed by histology. Despite surgical debridement and thorough washing, at each step we found the persistence of painting in the intermuscular septa by light microscopy. From 24 hours, a necroinflammatory process is set up with an influx of neutrophils, organizing themselves into micro-abscesses. It will be very deleterious, initially by encouraging risk of sepsis, and then facilitating the formation of extensive fibrosis, which is the cause of functional impairment. We established the kinetics of tissue under HPI with paint using an animal model. It appears that single emergency surgery is insufficient to manage this "septic compartment syndrome". Therefore, we recommend a systematic surgical "second look" at 48-72 hours to complete the debridement of residual inoculum and necrotic tissue without wound closure. Copyright © 2011. Published by Elsevier SAS.

  9. High Pressure In Situ X-ray Diffraction Study of MnO to 120 GPa and Comparison with Shock Compression Experiment

    Science.gov (United States)

    Yagi, Takehiko; Kondo, Tadashi; Syono, Yasuhiko

    1997-07-01

    In order to clarify the nature of the phase transformation in MnO observed at around 90 GPa by shock compression experiment (Syono et al., this symposium), high pressure in situ x-ray experiments were carried out up to 120 GPa. Powdered sample was directly compressed in Mao-Bell type diamond anvil and x-ray experiments were carried out using angle dispersive technique by combining synchrotron radiation and imaging plate detector. Distortion of the B1 structured phase into hexagonal unit cell was observed from 25-40 GPa, which continues to increase up to 90 GPa. At around 90 GPa, discontinuous change of the diffraction was observed. This new phase cannot be explained by a simple B2 structure and the analysis of this phase is in progress. This high pressure phase has metallic appearance, which reverses to transparent MnO on release of pressure.

  10. High-pressure pyrolysis study of C sub 3 N sub 6 H sub 6 : a route to preparing bulk C sub 3 N sub 4

    CERN Document Server

    Ma, H A; Chen, L X; Zhu, P W; Guo, W L; Guo, X B; Wang, Y D; Li, S Q; Zou Guang Tian; Zhang, G; Bex, P

    2002-01-01

    In order to prepare bulk C sub 3 N sub 4 , high-pressure pyrolysis of melamine (C sub 3 N sub 6 H sub 6) at different temperatures was carried out. The products were characterized by C, N, H element analysis, Fourier transform infrared spectroscopy, x-ray photoelectron spectroscopy, and x-ray diffractometry. The results of the analysis reveal that graphitic phase C sub 3 N sub 4 has been synthesized. It provides a novel route to synthesis of the theoretical superhard cubic C sub 3 N sub 4 and other C sub 3 N sub 4 phases from organic compounds by a high-pressure and high-temperature method.

  11. A study on variations of the low cycle fatigue life of a high pressure turbine nozzle caused by inlet temperature profiles and installation conditions

    International Nuclear Information System (INIS)

    Huh, Jae Sung; Kang, Young Seok; Rhee, Dong Ho; Seo, Do Young

    2015-01-01

    High pressure components of a gas turbine engine must operate for a long life under severe conditions in order to maximize the performance and minimize the maintenance cost. Enhanced cooling design, thermal barrier coating techniques, and nickel-base superalloys have been applied for overcoming them and furthermore, material modeling, finite element analysis, statistical techniques, and etc. in design stage have been utilized widely. This article aims to evaluate the effects on the low cycle fatigue life of the high pressure turbine nozzle caused by different turbine inlet temperature profiles and installation conditions and to investigate the most favorable operating condition to the turbine nozzle. To achieve it, the structural analysis, which utilized the results of conjugate heat transfer analysis as loading boundary conditions, was performed and its results were the input for the assessment of low cycle fatigue life at several critical zones

  12. Manometer extension for high pressure measurement: nuclear quadrupole resonance study of Cu2O with a modified Bridgman anvil cell up to 10 GPa.

    Science.gov (United States)

    Fukazawa, H; Yamatoji, N; Kohori, Y; Terakura, C; Takeshita, N; Tokura, Y; Takagi, H

    2007-01-01

    We report (63)Cu nuclear quadrupole resonance (NQR) measurement of Cu(2)O under pressure up to about 10 GPa at low temperatures. Because the lattice parameter of Cu(2)O changes with increasing pressure, the electric field gradient at the Cu site also changes correspondingly with pressure. This enables us to use the Cu(2)O as an in situ manometer for high pressure nuclear magnetic resonance/NQR up to about 9 GPa.

  13. Water solubility in pyrope at high pressures

    Science.gov (United States)

    Mookherjee, M.; Karato, S.-

    2006-12-01

    To address how much water is stored within the Earth's mantle, we need to understand the water solubility in the nominally anhydrous minerals. Much is known about olivine and pyroxene. Garnet is another important component, approaching 40% by volume in the transition zone. Only two studies on water solubility in pyrope at high-pressures exist which contradict each other. Lu and Keppler (1997) observed increase in water solubility in a natural pyrope up to 200 ppm wt of water, till 10 GPa. They concluded that the proton is located in the interstitial site. Withers et al. (1998) on the contrary, observed increasing water content in Mg-rich pyrope till 6 GPa, then sudden decrease of water, beyond detection, at 7 GPa. Based on infrared spectra, Withers et al. (1998), concluded hydrogarnet (Si^{4+} replaced by 4H+ to form O4H4) substitution in synthetic magnesium rich pyrope. They argued that at high pressure owing to larger volume, hydrogarnet substitution is unstable and water is expelled out of garnet. In transition zone conditions, however, majorite garnet seems to contain around 600-700 ppm wt of water (Bolfan-Casanova et al. 2000; Katayama et al. 2003). The cause for such discrepancy is not clear and whether garnet could store a significant amount of water at mantle condition is unconstrained. In order to understand the solubility mechanism of water in pyrope at high-pressure, we have conducted high- pressure experiments on naturally occurring single crystals of pyrope garnet (from Arizona, Aines and Rossman, 1984). To ascertain water-saturated conditions, we use olivine single-crystal as an internal standard. Preliminary results indicate that natural pyrope is capable of dissolving water at high-pressures, however, water preferentially enters olivine than in pyrope. We are undertaking systematic study to estimate the solubility of water in pyrope as a function of pressure. This will enable us to develop solubility models to understand the defect mechanisms

  14. Study of cements silicate phases hydrated under high pressure and high temperature; Etude des phases silicatees du ciment hydrate sous haute pression et haute temperature

    Energy Technology Data Exchange (ETDEWEB)

    Meducin, F.

    2001-10-01

    This study concerns the durability of oil-well cementing. Indeed, in oil well cementing a cement slurry is pumped down the steel casing of the well up the annular space between it and the surrounding rock to support and protect the casing. The setting conditions of pressure and temperature may be very high (up to 1000 bar and 250 deg C at the bottom of the oil-well). In this research, the hydration of the main constituent of cement, synthetic tri-calcium silicate Ca{sub 3}SiO{sub 2}, often called C{sub 3}S (C = CaO; S = SiO{sub 2} and H H{sub 2}O), is studied. Calcium Silicate hydrates are prepared in high-pressure cells to complete their phase diagram (P,T) and obtain the stability conditions for each species. Indeed, the phases formed in these conditions are unknown and the study consists in the hydration of C{sub 3}S at different temperatures, pressures, and during different times to simulate the oil-well conditions. In a first step (until 120 deg C at ambient pressure) the C-S-H, a not well crystallized and non-stoichiometric phase, is synthesized: it brings adhesion and mechanical properties., Then, when pressure and temperature increase, crystallized phases appear such as jaffeite (Ca{sub 6}(Si{sub 2}O{sub 7})(OH){sub 6}) and hillebrandite (Ca{sub 2}(SiO{sub 3})(OH){sub 2}). Silicon {sup 29}Si Nuclear Magnetic Resonance (using standard sequences MAS, CPMAS) allow us to identify all the silicates hydrates formed. Indeed, {sup 29}Si NMR is a valuable tool to determine the structure of crystallized or not-well crystallized phases of cement. The characterization of the hydrated samples is completed by other techniques: X- Ray Diffraction and Scanning Electron Microscopy. The following results are found: jaffeite is the most stable phase at C/S=3. To simulate the hydration of real cement, hydration of C{sub 3}S with ground quartz and with or without super-plasticizers is done. In those cases, new phases appear: kilchoanite mainly, and xonotlite. A large amount of

  15. High-Pressure Catalytic Reactions of C6 Hydrocarbons on PlatinumSingle-Crystals and nanoparticles: A Sum Frequency Generation VibrationalSpectroscopic and Kinetic Study

    Energy Technology Data Exchange (ETDEWEB)

    Bratlie, Kaitlin [Univ. of California, Berkeley, CA (United States)

    2007-01-01

    Catalytic reactions of cyclohexene, benzene, n-hexane, 2-methylpentane, 3-methylpentane, and 1-hexene on platinum catalysts were monitored in situ via sum frequency generation (SFG) vibrational spectroscopy and gas chromatography (GC). SFG is a surface specific vibrational spectroscopic tool capable of monitoring submonolayer coverages under reaction conditions without gas-phase interference. SFG was used to identify the surface intermediates present during catalytic processes on Pt(111) and Pt(100) single-crystals and on cubic and cuboctahedra Pt nanoparticles in the Torr pressure regime and at high temperatures (300K-450K). At low pressures (<10-6 Torr), cyclohexene hydrogenated and dehydrogenates to form cyclohexyl (C6H11) and π-allyl C6H9, respectively, on Pt(100). Increasing pressures to 1.5 Torr form cyclohexyl, π-allyl C6H9, and 1,4-cyclohexadiene, illustrating the necessity to investigate catalytic reactions at high-pressures. Simultaneously, GC was used to acquire turnover rates that were correlated to reactive intermediates observed spectroscopically. Benzene hydrogenation on Pt(111) and Pt(100) illustrated structure sensitivity via both vibrational spectroscopy and kinetics. Both cyclohexane and cyclohexene were produced on Pt(111), while only cyclohexane was formed on Pt(100). Additionally, π-allyl c-C6H9 was found only on Pt(100), indicating that cyclohexene rapidly dehydrogenates on the (100) surface. The structure insensitive production of cyclohexane was found to exhibit a compensation effect and was analyzed using the selective energy transfer (SET) model. The SET model suggests that the Pt-H system donates energy to the E2u mode of free benzene, which leads to catalysis. Linear C6 (n-hexane, 2-methylpentane, 3-methylpentane, and 1-hexene) hydrocarbons were also investigated in the presence and absence of excess hydrogen on Pt

  16. High pressure research at CHESS

    International Nuclear Information System (INIS)

    Brister, K.

    1992-01-01

    Since February 1990 there has been a dedicated high pressure line at the Cornell High Energy Synchrotron Source (CHESS). This facility provides X-ray instrumentation for energy dispersive X-ray diffraction and Laue diffraction using diamond anvil cells. Both hard-bend magnet and wiggler radiation are available as well as focused monochromatic radiation. In addition, support instrumentation is also available; a ruby system, laser heating, sample loading, and data analysis software. Experienced users need only to bring their diamond anvil cells and samples and can leave with the initial data analysis finished. Research using diamond anvil cells will be introduced and the facility will be described. Some of the diamond anvil cell research done at CHESS will be reviewed, including crystalline to amorphous transitions (R.R. Winters et al., Chem. Phys, in press), properties of C 6 0 under stress (S.J. Duclos et al., Nature 351 (1991) 380), deep earthquakes (T.C. Wu et al., submitted to J. Geophys. Res.)l, and reaching pressures of the center of Earth (A.L. Ruoff et al., Rev. Sci. Instr. 61 (1990) 3830). (orig.)

  17. Conventional high pressure techniques fro neutron diffraction

    International Nuclear Information System (INIS)

    Mizuki, Jun-ichiro; Endoh, Yasuo

    1981-01-01

    Conventional high pressure techniques using a clamped type pressure cell have been adapted for studies by neutron diffraction. Careful calibration of the pressure sensing apparatus and an appropriate choice of pressure transmitting medium enable accurate neutron diffraction measurements to be made at reduced temperature as low as 4 K. In the present studies we have demonstrated that using the clamped type microbomb neutron diffraction measurements can be easily made under the pressure up to 5 kbar within the temperature range 4 K - 350 K. (author)

  18. Mechanical properties of dense zeolitic imidazolate frameworks (ZIFs): a high-pressure X-ray diffraction, nanoindentation and computational study of the zinc framework Zn(Im)2, and its lithium-boron analogue, LiB(Im)4.

    Science.gov (United States)

    Bennett, Thomas D; Tan, Jin-Chong; Moggach, Stephen A; Galvelis, Raimondas; Mellot-Draznieks, Caroline; Reisner, Barbara A; Thirumurugan, A; Allan, David R; Cheetham, Anthony K

    2010-09-17

    The dense, anhydrous zeolitic imidazolate frameworks (ZIFs), Zn(Im)(2) (1) and LiB(Im)(4) (2), adopt the same zni topology and differ only in terms of the inorganic species present in their structures. Their mechanical properties (specifically the Young's and bulk moduli, along with the hardness) have been elucidated by using high pressure, synchrotron X-ray diffraction, density functional calculations and nanoindentation studies. Under hydrostatic pressure, framework 2 undergoes a phase transition at 1.69 GPa, which is somewhat higher than the transition previously reported in 1. The Young's modulus (E) and hardness (H) of 1 (E≈8.5, H≈1 GPa) is substantially higher than that of 2 (E≈3, H≈0.1 GPa), whilst its bulk modulus is relatively lower (≈14 GPa cf. ≈16.6 GPa). The heavier, zinc-containing material was also found to be significantly harder than its light analogue. The differential behaviour of the two materials is discussed in terms of the smaller pore volume of 2 and the greater flexibility of the LiN(4) tetrathedron compared with the ZnN(4) and BN(4) units.

  19. Study on the effect of distance between the two nozzle holes on interaction of high pressure combustion-gas jets with liquid

    International Nuclear Information System (INIS)

    Xue, Xiaochun; Yu, Yonggang; Zhang, Qi

    2014-01-01

    Highlights: • We design a five-stage cylindrical stepped-wall chamber to study twin combustion-gas jets. • We observe mixing processes of twin combustion-gases and liquid by high speed photographic system. • We discuss the influence of multiple parameters on expansion shape of the Taylor cavities. • The three-dimensional mathematics model is established to simulate the energy release process. • We obtain distribution characteristics of parameters under different nozzle distances. - Abstract: The combustion-gas generator and cylindrical stepped-wall observation chambers with five stages are designed to study the expansion characteristic of twin combustion-gas jets in liquid working medium under high temperature and high pressure. The expansion processes of Taylor cavities formed by combustion-gas jets and the mixing characteristics of gas–liquid are studied by means of high-speed digital camera system. The effects of the distance between the two nozzle holes, injection pressure and nozzle diameter on jet expansion processes are discussed. The experimental results indicate that, the velocity differences exist on the gas–liquid interface during expansion processes of twin combustion-gas jets, and the effect of Taylor–Helmholtz instability is intense, so interfaces between gas and liquid show turbulent folds and randomness. The strong turbulent mixing of gas and liquid leads to release of combustion-gas energy with the temperature decreasing. Moreover, the mixing effectiveness is obviously enhanced on the corners of each step of the cylindrical stepped-wall structure, forming radial expansion phenomenon. The reasonable matching of multi-parameter can restrain the jet instability and make the combustion-gas energy orderly release. Based on the experiments, the three-dimensional unsteady mathematical model of interaction of twin combustion-gas jets and liquid working medium is established to obtain the density, pressure, velocity and temperature

  20. High pressure in situ X-ray diffraction study of MnO to 137 GPa and comparison with shock compression experiment

    Science.gov (United States)

    Yagi, T.; Kondo, T.; Syono, Y.

    1998-07-01

    In order to clarify the nature of the phase transformation in MnO observed at around 90 GPa by shock compression experiment, high pressure in situ X-ray observations were carried out up to 137 GPa. Powdered sample was directly compressed in Mao-Bell type diamond anvil cell and X-ray experiments were carried out using angle dispersive technique by combining synchrotron radiation and imaging plate detector. Distortion of the B1 structured phase was observed above about 40 GPa, which continues to increase up to 90 GPa. Two discontinuous changes of the diffraction profiles were observed at around 90 GPa and 120 GPa. The nature of the intermediate phase between 90 GPa and 120 GPa is not clear yet. It is neither cesium chloride (B2) nor nickel arsenide (B8) structure. On the other hand, the diffraction profile above 120 GPa can be reasonably well explained by the B8 structure. High pressure phases above 90 GPa have metallic luster and all the transformations are reversible on release of pressure.

  1. Role of the lattice in the gamma-->alpha phase transition of Ce: a high-pressure neutron and x-ray diffraction study.

    Science.gov (United States)

    Jeong, I-K; Darling, T W; Graf, M J; Proffen, Th; Heffner, R H; Lee, Yongjae; Vogt, T; Jorgensen, J D

    2004-03-12

    The temperature and pressure dependence of the thermal displacements and lattice parameters were obtained across the gamma-->alpha phase transition of Ce using high-pressure, high-resolution neutron and synchrotron x-ray powder diffraction. The estimated vibrational entropy change per atom in the gamma-->alpha phase transition, DeltaS(gamma-alpha)(vib) approximately (0.75+/-0.15)k(B), is about half of the total entropy change. The bulk modulus follows a power-law pressure dependence that is well described using the framework of electron-phonon coupling. These results clearly demonstrate the importance of lattice vibrations, in addition to the spin and charge degrees of freedom, for a complete description of the gamma-->alpha phase transition in elemental Ce.

  2. Anomalous thermal expansion, negative linear compressibility, and high-pressure phase transition in ZnAu2(CN) 4 : Neutron inelastic scattering and lattice dynamics studies

    Science.gov (United States)

    Gupta, Mayanak K.; Singh, Baltej; Mittal, Ranjan; Zbiri, Mohamed; Cairns, Andrew B.; Goodwin, Andrew L.; Schober, Helmut; Chaplot, Samrath L.

    2017-12-01

    We present temperature-dependent inelastic-neutron-scattering measurements, accompanied by ab initio calculations of the phonon spectra and elastic properties as a function of pressure to quantitatively explain an unusual combination of negative thermal expansion and negative linear compressibility behavior of ZnAu2(CN) 4 . The mechanism of the negative thermal expansion is identified in terms of specific anharmonic phonon modes that involve bending of the -Zn-NC-Au-CN-Zn- linkage. The soft phonon at the L point at the Brillouin zone boundary quantitatively relates to the high-pressure phase transition at about 2 GPa. The ambient pressure structure is also found to be close to an elastic instability that leads to a weakly first-order transition.

  3. Experimental and numerical study of heterogeneous pressure-temperature-induced lethal and sublethal injury of Lactococcus lactis in a medium scale high-pressure autoclave.

    Science.gov (United States)

    Kilimann, K V; Kitsubun, P; Delgado, A; Gänzle, M G; Chapleau, N; Le Bail, A; Hartmann, C

    2006-07-05

    The present contribution is dedicated to experimental and theoretical assessment of microbiological process heterogeneities of the high-pressure (HP) inactivation of Lactococcus lactis ssp. cremoris MG 1363. The inactivation kinetics are determined in dependence of pressure, process time, temperature and absence or presence of co-solutes in the buffer system namely 4 M sodium chloride and 1.5 M sucrose. The kinetic analysis is carried out in a 0.1-L autoclave in order to minimise thermal and convective effects. Upon these data, a deterministic inactivation model is formulated with the logistic equation. Its independent variables represent the counts of viable cells (viable but injured) and of the stress-resistant cells (viable and not injured). This model is then coupled to a thermo-fluiddynamical simulation method, high-pressure computer fluid dynamics technique (HP-CFD), which yields spatiotemporal temperature and flow fields occurring during the HP application inside any considered autoclave. Besides the thermo-fluiddynamic quantities, the coupled model predicts also the spatiotemporal distribution of both viable (VC) and stress-resistant cell counts (SRC). In order to assess the process non-uniformity of the microbial inactivation in a 3.3-L autoclave experimentally, microbial samples are placed at two distinct locations and are exposed to various process conditions. It can be shown with both, experimental and theoretical models that thermal heterogeneities induce process non-uniformities of more than one decimal power in the counts of the viable cells at the end of the treatment. (c) 2006 Wiley Periodicals, Inc.

  4. High pressure experimental studies on Na3Fe(PO4)(CO3) and Na3Mn(PO4)(CO3): Extensive pressure behaviors of carbonophosphates family

    Science.gov (United States)

    Gao, Jing; Huang, Weifeng; Wu, Xiang; Qin, Shan

    2018-04-01

    Carbon-bearing phases in the Earth's interior have profound implications for the long-term Earth carbon cycle. Here we investigate high-pressure behaviors of carbonophosphates bonshtedtite Na3Fe(PO4)(CO3) and sidorenkite Na3Mn(PO4)(CO3) in diamond anvil cells up to ∼12 GPa at room temperature. Modifications in in situ synchrotron X-ray diffraction patterns and Raman spectra confirm the structural stability of carbonophosphates within the pressure region. Fitting the third-order Birch-Murnaghan equation of state to the volume compression curve, the isothermal bulk modulus parameters are obtained to be K0 = 56(1) GPa, K0' = 3.3(1), V0 = 303.3(3) Å3 for Na3Fe(PO4)(CO3) and K0 = 54(1) GPa, K0' = 3.4(1), V0 = 313.4(2) Å3 for Na3Mn(PO4)(CO3). Crystallographic axes exhibit an elastic anisotropy with a more compressible c-axis relative to the ab-plane. An inverse linear correlation between the K0 value and the ionic radius of M2+ (M = Mg, Fe, Mn) is well determined for carbonophosphates. The pressure-dependence responsiveness of [PO4] and [CO3] in carbonophosphates show a negative relationship to the M2+ radius. We also discussed the effect of [PO4] group on the structural variations and high-pressure behaviors of carbonates. Furthermore, the geochemical properties of carbonophosphates hold implications to diamond genesis.

  5. Single-crystal X-ray diffraction study of SrGeO3 high-pressure perovskite phase at 100 K

    Science.gov (United States)

    Nakatsuka, Akihiko; Arima, Hiroshi; Ohtaka, Osamu; Fujiwara, Keiko; Yoshiasa, Akira

    2017-10-01

    Single-crystal X-ray diffraction study of SrGeO3 perovskite (cubic; space group Pmɜ¯m) synthesized at 6 GPa and 1223 K was conducted at a low temperature of 100 K. The residual electron density revealed the presence of the bonding electron at the center of the Ge-O bond, in accordance with our previous conclusion that the Ge-O bond is strongly covalent. From comparison with our previous structure-refinement result at 296 K, the mean square displacement (MSD) of the O atom in the direction of the Ge-O bond is suggested to exhibit no significant temperature dependence, in contrast to that in the direction perpendicular to the bond. Thus, the strong covalency of the Ge-O bond can have a large influence on the temperature dependence of thermal vibration of the O atom.

  6. Solids, liquids, and gases under high pressure

    Science.gov (United States)

    Mao, Ho-Kwang; Chen, Xiao-Jia; Ding, Yang; Li, Bing; Wang, Lin

    2018-01-01

    Pressure has long been recognized as a fundamental thermodynamic variable but its application was previously limited by the available pressure vessels and probes. The development of megabar diamond anvil cells and a battery of associated in-laboratory and synchrotron techniques at the turn of the century have opened a vast new window of opportunities. With the addition of the pressure dimension, we are facing a new world with an order of magnitude more materials to be discovered than all that have been explored at ambient pressure. Pressure drastically and categorically alters all elastic, electronic, magnetic, structural, and chemical properties, and pushes materials across conventional barriers between insulators and superconductors, amorphous and crystalline solids, ionic and covalent compounds, vigorously reactive and inert chemicals, etc. In the process, it reveals surprising high-pressure physics and chemistry and creates novel materials. This review describes the principles and methodology used to reach ultrahigh static pressure: the in situ probes, the physical phenomena to be investigated, the long-pursued goals, the surprising discoveries, and the vast potential opportunities. Exciting examples include the quest for metallic hydrogen, the record-breaking superconducting temperature of 203 K in HnS , the complication of "free-electron gas" alkali metals, the magnetic collapse in 3 d transition elements, the pressure-induced superconductivity from topological insulators, the novel stoichiometry in simple compounds, the interaction of nanoscience, the accomplishment of 750 GPa pressure, etc. These highlights are the integral results of technological achievements, specific measurements, and theoretical advancement; therefore, the same highlights will appear in different sections corresponding to these different aspects. Overall, this review demonstrates that high-pressure research is a new dimension in condensed-matter physics.

  7. Neutron diffraction under high pressure and high temperature

    International Nuclear Information System (INIS)

    Komatsu, Kazuki

    2010-01-01

    Neutron diffraction study under high pressure and high temperature is reviewed from the technical point of view. Particularly, cell assembly for the high-PT neutron diffraction using a Paris-Edinburgh cell with the temperature calibration by neutron resonance spectroscopy is introduced. Notes on the errors relevant to high pressure and high temperature experiments in both monochromatic angle dispersive and time-of-flight methods are also discussed. (author)

  8. Practical conditions in the neutron diffraction under high pressure

    International Nuclear Information System (INIS)

    Kamigaki, Kazuo; Ohashi, Masayoshi

    1993-01-01

    Practical analysis is made on some conditions in utilizing neutrons for the study of atomistic structure of materials under high pressure. Investigation is made on the geometrical conditions; size of the specimen, width of slits, and the rate of extra-scattering. Experiments are performed on the effects of absorption by high pressure cell and the disturbance due to an overlapping of diffraction peaks. An observation is presented on the pressure-induced transformation in RbBr. (author)

  9. Depth Gauge for Liquids Under High Pressure

    Science.gov (United States)

    Zuckerwar, A. J.; Mazel, D. S.

    1987-01-01

    Piezoelectric element mounted in hole drilled in high-pressure plug. Transducer used to measure depth of liquid when pressure in vessel high. New configuration transmits ultrasonic vibration directly into liquid, enhancing signal strength, accuracy, and range, yet piezoelectric element protected from high-pressure liquid.

  10. Coal swelling and thermoplasticity under high pressure

    Energy Technology Data Exchange (ETDEWEB)

    Ndaji, F.E.; Butterfield, I.M.; Thomas, K.M. (Newcastle upon Tyne University, Newcastle upon Tyne (United Kingdom). Northern Carbon Research Labs., Dept. of Chemistry)

    1992-01-01

    The literature on the following topics is reviewed: swelling and agglomeration of coal; measurements of swelling index and dilatometric and plastometric properties at high pressures; and the effects of oxidation, tar addition and minerals on high-pressure thermoplastic properties. 34 refs., 6 figs.

  11. Soret Effect Study on High-Pressure CO2-Water Solutions Using UV-Raman Spectroscopy and a Concentric-Tube Optical Cell

    Energy Technology Data Exchange (ETDEWEB)

    Windisch, Charles F.; McGrail, B. Peter; Maupin, Gary D.

    2012-01-01

    Spatially resolved deep-UV Raman spectroscopy was applied to solutions of CO2 and H2O (or D2O), which were subject to a temperature gradient in a thermally regulated high-pressure concentric-tube Raman cell in an attempt to measure a Soret effect in the vicinity of the critical point of CO2. Although Raman spectra of solutions of CO2 dissolved in D2O at 10 MPa and temperatures near the critical point of CO2 had adequate signal-to-noise and spatial resolution to observe a Soret effect with a Soret coefficient with magnitude of |ST| > 0.03, no evidence for an effect of this size was obtained for applied temperature gradients up to 19oC. The presence of 1 M NaCl did not make a difference. In contrast, the concentration of CO2 dissolved in H2O was shown to vary significantly across the temperature gradient when excess CO2 was present, but the results could be explained simply by the variation in CO2 solubility over the temperature range and not to kinetic factors. For mixtures of D2O dissolved in scCO2 at 10 MPa and temperatures close to the critical point of CO2, the Raman peaks for H2O were too weak to measure with confidence even at the limit of D2O solubility.

  12. Sizing of high-pressure restriction orifices

    International Nuclear Information System (INIS)

    Casado Flores, E.

    1995-01-01

    Constant up-grading of power plants sometimes requires the modification of components which form part of suppliers' packages. In order to protect technology they have developed, however, the suppliers do not supply their calculation criteria. In order to reduce the costs of such improvements, and so as to be able to undertake the modification without having to rely on the original supplier, this paper describes the basic criteria applicable to the study of high-pressure restriction orifices, which can be considered to be representative of the components in question. The restriction orifices discussed are: - Insert - Multiplates in series with one perforation in each plate - Multiplates in series with several perforations in each plate For each type, an explanation of their sizing is given, together with the equations relating the corresponding flow and pressure drop. (Author)

  13. Urea and deuterium mixtures at high pressures

    Energy Technology Data Exchange (ETDEWEB)

    Donnelly, M., E-mail: m.donnelly-2@sms.ed.ac.uk; Husband, R. J.; Frantzana, A. D.; Loveday, J. S. [Centre for Science at Extreme Conditions and School of Physics and Astronomy, The University of Edinburgh, Erskine Williamson Building, Peter Guthrie Tait Road, The King’s Buildings, Edinburgh EH9 3FD (United Kingdom); Bull, C. L. [ISIS, Rutherford Appleton Laboratory, Oxford Harwell, Didcot OX11 0QX (United Kingdom); Klotz, S. [IMPMC, CNRS UMR 7590, Université P and M Curie, 4 Place Jussieu, 75252 Paris (France)

    2015-03-28

    Urea, like many network forming compounds, has long been known to form inclusion (guest-host) compounds. Unlike other network formers like water, urea is not known to form such inclusion compounds with simple molecules like hydrogen. Such compounds if they existed would be of interest both for the fundamental insight they provide into molecular bonding and as potential gas storage systems. Urea has been proposed as a potential hydrogen storage material [T. A. Strobel et al., Chem. Phys. Lett. 478, 97 (2009)]. Here, we report the results of high-pressure neutron diffraction studies of urea and D{sub 2} mixtures that indicate no inclusion compound forms up to 3.7 GPa.

  14. First-principles study on oxidation effects in uranium oxides and high-pressure high-temperature behavior of point defects in uranium dioxide

    Science.gov (United States)

    Geng, Hua Y.; Song, Hong X.; Jin, K.; Xiang, S. K.; Wu, Q.

    2011-11-01

    Formation Gibbs free energy of point defects and oxygen clusters in uranium dioxide at high-pressure high-temperature conditions are calculated from first principles, using the LSDA+U approach for the electronic structure and the Debye model for the lattice vibrations. The phonon contribution on Frenkel pairs is found to be notable, whereas it is negligible for the Schottky defect. Hydrostatic compression changes the formation energies drastically, making defect concentrations depend more sensitively on pressure. Calculations show that, if no oxygen clusters are considered, uranium vacancy becomes predominant in overstoichiometric UO2 with the aid of the contribution from lattice vibrations, while compression favors oxygen defects and suppresses uranium vacancy greatly. At ambient pressure, however, the experimental observation of predominant oxygen defects in this regime can be reproduced only in a form of cuboctahedral clusters, underlining the importance of defect clustering in UO2+x. Making use of the point defect model, an equation of state for nonstoichiometric oxides is established, which is then applied to describe the shock Hugoniot of UO2+x. Furthermore, the oxidization and compression behavior of uranium monoxide, triuranium octoxide, uranium trioxide, and a series of defective UO2 at 0 K are investigated. The evolution of mechanical properties and electronic structures with an increase of the oxidation degree are analyzed, revealing the transition of the ground state of uranium oxides from metallic to Mott insulator and then to charge-transfer insulator due to the interplay of strongly correlated effects of 5f orbitals and the shift of electrons from uranium to oxygen atoms.

  15. Structure and phase diagram of an adhesive colloidal dispersion under high pressure: a small angle neutron scattering, diffusing wave spectroscopy, and light scattering study.

    Science.gov (United States)

    Vavrin, R; Kohlbrecher, J; Wilk, A; Ratajczyk, M; Lettinga, M P; Buitenhuis, J; Meier, G

    2009-04-21

    We have applied small angle neutron scattering (SANS), diffusing wave spectroscopy (DWS), and dynamic light scattering (DLS) to investigate the phase diagram of a sterically stabilized colloidal system consisting of octadecyl grafted silica particles dispersed in toluene. This system is known to exhibit gas-liquid phase separation and percolation, depending on temperature T, pressure P, and concentration phi. We have determined by DLS the pressure dependence of the coexistence temperature and the spinodal temperature to be dP/dT=77 bar/K. The gel line or percolation limit was measured by DWS under high pressure using the condition that the system became nonergodic when crossing it and we determined the coexistence line at higher volume fractions from the DWS limit of turbid samples. From SANS measurements we determined the stickiness parameter tau(B)(P,T,phi) of the Baxter model, characterizing a polydisperse adhesive hard sphere, using a global fit routine on all curves in the homogenous regime at various temperatures, pressures, and concentrations. The phase coexistence and percolation line as predicted from tau(B)(P,T,phi) correspond with the determinations by DWS and were used to construct an experimental phase diagram for a polydisperse sticky hard sphere model system. A comparison with theory shows good agreement especially concerning the predictions for the percolation threshold. From the analysis of the forward scattering we find a critical scaling law for the susceptibility corresponding to mean field behavior. This finding is also supported by the critical scaling properties of the collective diffusion.

  16. Timing and duration of Variscan high-pressure metamorphism in the French Massif Central: A multimethod geochronological study from the Najac Massif

    Science.gov (United States)

    Lotout, Caroline; Pitra, Pavel; Poujol, Marc; Anczkiewicz, Robert; Van Den Driessche, Jean

    2018-05-01

    Accurate dating of eclogite-facies metamorphism is of paramount importance in order to understand the tectonic evolution of an orogen. An eclogite sample from the Najac Massif (French Massif Central, Variscan belt) displays a zircon-bearing garnet-omphacite-amphibole-rutile-quartz peak assemblage. Pseudosection modeling suggests peak pressure conditions of 15-20 kbar, 560-630 °C. Eclogite-facies garnet displays Lu-enriched cores and Sm-rich rims and yields a Lu-Hf age of 382.8 ± 1.0 Ma and a Sm-Nd age of 376.7 ± 3.3 Ma. The ages are interpreted as marking the beginning of the prograde garnet growth during the initial stages of the eclogite-facies metamorphism, and the high-pressure (and temperature) peak reached by the rock, respectively. Zircon grains display chondrite-normalized REE spectra with variably negative, positive or no Eu anomalies and are characterized by either enriched or flat HREE patterns. However, they yield a well constrained in situ LA-ICP-MS U-Pb age of 385.5 ± 2.3 Ma, despite this REE pattern variability. Zr zonation in garnet, Y content in zircon and the diversity of zircon HREE spectra may suggest that zircon crystallized prior to and during incipient garnet growth on the prograde P-T path, recording the initial stages of the eclogite-facies conditions. Consequently, the zircon age of 385.5 ± 2.3 Ma, comparable within error with the Lu-Hf age obtained on garnet, is interpreted as dating the beginning of the eclogite-facies metamorphism. Accordingly, the duration of the prograde part of the eclogite-facies event is estimated at 6.1 ± 4.3 Myr. Subsequent exhumation is constrained by an apatite U-Pb age at 369 ± 13 Ma.

  17. Transportable, small high-pressure preservation vessel for cells

    International Nuclear Information System (INIS)

    Kamimura, N; Sotome, S; Shimizu, A; Nakajima, K; Yoshimura, Y

    2010-01-01

    We have previously reported that the survival rate of astrocytes increases under high-pressure conditions at 4 0 C. However, pressure vessels generally have numerous problems for use in cell preservation and transportation: (1) they cannot be readily separated from the pressurizing pump in the pressurized state; (2) they are typically heavy and expensive due the use of materials such as stainless steel; and (3) it is difficult to regulate pressurization rate with hand pumps. Therefore, we developed a transportable high-pressure system suitable for cell preservation under high-pressure conditions. This high-pressure vessel has the following characteristics: (1) it can be easily separated from the pressurizing pump due to the use of a cock-type stop valve; (2) it is small and compact, is made of PEEK and weighs less than 200 g; and (3) pressurization rate is regulated by an electric pump instead of a hand pump. Using this transportable high-pressure vessel for cell preservation, we found that astrocytes can survive for 4 days at 1.6 MPa and 4 0 C.

  18. Combined in situ Synchrotron X-ray Diffraction and Ultrasonic Interferometry Study of Ε-FeSi at High Pressure and Temperature

    International Nuclear Information System (INIS)

    Whitaker, M.; Liu, W.; Liu, Q.; Wang, L.; Li, B.

    2008-01-01

    Ultrasonic interferometry was used in combination with synchrotron X-radiation to determine the compressional and shear wave velocities and unit-cell volumes of Ε-FeSi (cubic B20 structure) at room temperature and pressures up to ∼12 GPa. The data collected during compression are compared with those collected during decompression after heating to release stress within the sample cell. By fitting all of the decompression unit-cell volume and sound velocity data to third-order finite-strain equations, we obtain the adiabatic zero-pressure bulk and shear moduli and their first pressure derivatives: K S0 =169.3 (8) GPa, G 0 =116.3 (4) GPa, K'S0=6.5(3), G'0=3.0(1). The bulk modulus obtained from this study is in good agreement with those of some previous experimental studies, but significantly lower than those obtained by first-principle calculations. This study presents the first direct measurement on the shear properties of this phase.

  19. Subduction of Proterozoic to Late Triassic continental basement in the Guatemala suture zone: A petrological and geochronological study of high-pressure metagranitoids from the Chuacús complex

    Science.gov (United States)

    Maldonado, Roberto; Ortega-Gutiérrez, Fernando; Ortíz-Joya, Guillermo A.

    2018-05-01

    Many continental subduction complexes contain abundant granitic rocks coexisting with minor volumes of eclogite-facies rocks. Characterization of granitic protoliths is crucial to decipher the origin of subducted continental crust, whereas knowledge of its metamorphic evolution is required to constrain the mechanisms of burial and exhumation. In this work we present geochronological and petrological evidence that demonstrate the occurrence of a subducted Proterozoic to Late Triassic granitic basement in the Chuacús complex of central Guatemala. Metagranitoids exposed in this area are interlayered with eclogite and other high-pressure rocks, and their structure is considerably variable due to strain partitioning during deformation. Laser ablation-inductively coupled plasma-mass spectrometry U-Pb zircon data from two ferroan metagranites yield protolith crystallization ages of ca. 1.1 Ga and their trace-element abundances suggest an origin related to intraplate magmatism, while a high-silica, peraluminous metagranite is dated at 1.0 Ga and was probably originated by partial melting of a high-grade continental crust. On the other hand, two megacrystic to augen metagranitoids yield protolith crystallization ages of ca. 224 Ma, which are identical within errors to the protolith age of hosted eclogitic metabasites. Their high incompatible trace element abundances together with the observed spatial-temporal relationships with mafic protoliths suggest that Late Triassic bimodal magmatism in the Chuacús complex was probably originated in a within-plate setting. Regardless of their age or structure, the studied metagranites preserve evidences for high-pressure metamorphic equilibration, such as the occurrence of Ca-rich garnet (XCa up to 0.52) in association with phengite (Si contents of up to 3.4 pfu) and rutile. The integration of Zr-in-rutile thermometry and phengite barometry allows the peak metamorphic conditions to be constrained at 640-680 °C and 13 kbar. This

  20. Some characteristics of the digitization pulses from high pressure neon-helium flash tubes

    International Nuclear Information System (INIS)

    Chan, D.S.K.; Leung, S.K.; Ng, L.K.

    1979-01-01

    Characteristics of the digitization output pulses from high pressure neon-helium flash tubes were studied under various operation conditions using square ultra-high voltage pulses. Properties reported by previous workers were compared. Two discharge mechanisms, the Townsend avalanche discharge and the streamer discharge, were observed to occur in sequence in some events. The output waveforms for both discharge mechanisms were studied in detail. The charge induced on a detecting probe was also estimated from the measured data. (Auth.)

  1. Application of High Pressure in Food Processing

    Directory of Open Access Journals (Sweden)

    Herceg, Z.

    2011-01-01

    Full Text Available In high pressure processing, foods are subjected to pressures generally in the range of 100 – 800 (1200 MPa. The processing temperature during pressure treatments can be adjusted from below 0 °C to above 100 °C, with exposure times ranging from a few seconds to 20 minutes and even longer, depending on process conditions. The effects of high pressure are system volume reduction and acceleration of reactions that lead to volume reduction. The main areas of interest regarding high-pressure processing of food include: inactivation of microorganisms, modification of biopolymers, quality retention (especially in terms of flavour and colour, and changes in product functionality. Food components responsible for the nutritive value and sensory properties of food remain unaffected by high pressure. Based on the theoretical background of high-pressure processing and taking into account its advantages and limitations, this paper aims to show its possible application in food processing. The paper gives an outline of the special equipment used in highpressure processing. Typical high pressure equipment in which pressure can be generated either by direct or indirect compression are presented together with three major types of high pressure food processing: the conventional (batch system, semicontinuous and continuous systems. In addition to looking at this technology’s ability to inactivate microorganisms at room temperature, which makes it the ultimate alternative to thermal treatments, this paper also explores its application in dairy, meat, fruit and vegetable processing. Here presented are the effects of high-pressure treatment in milk and dairy processing on the inactivation of microorganisms and the modification of milk protein, which has a major impact on rennet coagulation and curd formation properties of treated milk. The possible application of this treatment in controlling cheese manufacture, ripening and safety is discussed. The opportunities

  2. A High Pressure Apparatus for Neutron Diffraction

    OpenAIRE

    Kazuo, Kamigaki; Hajime, Yoshida; Masayoshi, Ohashi; Takejiro, Kaneko; Kozaburo, Sato; The Research Institute for Iron, Steel and Other Metals; The Research Institute for Iron, Steel and Other Metals; The Research Institute for Iron, Steel and Other Metals; The Research Institute for Iron, Steel and Other Metals; Department of Physics, Faculty of Science, Hirosaki University

    1980-01-01

    A high pressure apparatus was developed for thermal neutron diffraction of time-of-flight method. The high pressure vessel was a piston-cylinder type, and Ti-Zr alloy was used as a material of the cylinder. The coherent scattering of neutron is suppressed in Ti-53wt% Zr alloy. The diffraction spectrum is formed of peaks from the specimen and a background, which corresponds to the energy distribution of the incident neutron. High pressure measurements were made in RbBr on the transformation be...

  3. Structure and stability of hydrous minerals at high pressure

    Science.gov (United States)

    Duffy, T. S.; Fei, Y.; Meade, C.; Hemley, R. J.; Mao, H. K.

    1994-01-01

    The presence of even small amounts of hydrogen in the Earth's deep interior may have profound effects on mantle melting, rheology, and electrical conductivity. The recent discovery of a large class of high-pressure H-bearing silicates further underscores the potentially important role for hydrous minerals in the Earth's mantle. Hydrogen may also be a significant component of the Earth's core, as has been recently documented by studies of iron hydride at high pressure. In this study, we explore the role of H in crystal structures at high pressure through detailed Raman spectroscopic and x ray diffraction studies of hydrous minerals compressed in diamond anvil cells. Brucite, Mg(OH)2, has a simple structure and serves as an analogue for the more complex hydrous silicates. Over the past five years, this material has been studied at high pressure using shock-compression, powder x ray diffraction, infrared spectroscopy, Raman spectroscopy, and neutron diffraction. In addition, we have recently carried out single-crystal synchrotron x-ray diffraction on Mg(OH)2 and Raman spectroscopy on Mg(OD)2 at elevated pressure. From all these studies, an interesting picture of the crystal chemical behavior of this material at high pressure is beginning to emerge. Some of the primary conclusions are as follows: First, hydrogen bonding is enhanced by the application of pressure. Second, layered minerals which are elastically anisotropic at low pressure may not be so at high pressure. Furthermore, the brucite data place constraints on the effect of hydrogen on seismic velocities and density at very high pressure. Third, the stability of hydrous minerals may be enhanced at high P by subtle structural rearrangements that are difficult to detect using traditional probes and require detailed spectroscopic analyses. Finally, brucite appears to be unique in that it undergoes pressure-induced disordering that is confined solely to the H-containing layers of the structure.

  4. Application of LITGs diagnostics to trace detection of NOx in high pressure combustors: a propedeutic study in a cell at controlled conditions

    Energy Technology Data Exchange (ETDEWEB)

    Fantoni, R.; Giorgi, M. [ENEA, Centro Ricerche Frascati, Frascati RM (Italy). Dipt. Innovazione

    1999-07-01

    The field of the interference pattern of two laser beams, either on or off resonance with an allowed transition in a medium, generates spatial modulations of its complex refractive index called Laser Induced Gratings (LIGs). After the excitation, the subsequent release of internal energy in the form of heat, in gases, due to collisional relaxation, may lead to the formation of thermal gratings (LITGs). The temporal evolution of a LIG can be investigated by using a CW laser as a probe. The temporal behavior of LITGs depends on the rate of the energy thermalization, e.g. a fast energy release generates a standing acoustic wave and a stationary density modulation with equal amplitudes, whereas a slow energy release favours the formation of the stationary density modulation whereas the development of the acoustic contribution is suppressed. In case of a multi-step thermalization process, with different time constants involved, oscillatory and stationary contributions to LITGs can be observed. LITGs experiments have been performed with NO{sub 2} molecules diluted in different buffer gases in order to establish the possibilities to trace this species at high pressure and high temperature in combustion exhaust pipes. [Italian] Il campo d'interferenza di due fasci laser, sia risonante che non con una transizione permessa in un mezzo, genera modulazion spaziali del suo indice di rifrazione complesso dette reticoli indotti da laser (Laser Induced Gratings con acronimo LIGs). Nel gas dopo l'eccitazione, il susseguente rilascio di energia genera le oscillazioni caratteristiche di un'onda acustica, mentre un rilascio di energia lento tende a sopprimere il contributo della componente acustica. Nel caso di un processo di termalizzazione multiplo, a cui contribuiscono diverse constanti di tempo, si possono osservare contemporaneamente contributi sia oscillanti che stazionari ai LITGs. Gli esperimenti sono stati effettuati con molecole di NO{sub 2} diluite in diversi

  5. High pressure study of low compressibility tetracalcium aluminum carbonate hydrates 3CaO·Al2O3·CaCO3·11H2O

    KAUST Repository

    Moon, Juhyuk

    2012-01-01

    Synchrotron X-ray diffraction data was collected from a sample of monocarboaluminate 3CaO•Al2O3•CaCO 3•11H2O from ambient pressure to 4.3 GPa. The refined crystal structure at ambient pressure is triclinic with parameters a = 5.77(2) Å, b = 8.47(5) Å, c = 9.93(4) Å, α = 64.6(2)°, β = 82.8(3)°, γ = 81.4(4)°, and space group of P1 or P1̄. It showed some degree of perfectly reversible pressure-induced dehydration with a non-hygroscopic pressure-transmitting medium. However the dehydration effect does not critically affect a bulk modulus due to its strong framework. The isothermal bulk modulus of monocarboaluminate was found to be 53(5) GPa and 54(4) GPa with 3rd order and 2nd order Birch-Murnaghan Equation of state, respectively. That value is higher than for any other reported AFm or AFt phase. The pressure-volume behavior of the monocarboaluminate was compared with that of previous studied hemicarboaluminate. © 2011 Elsevier Ltd. All rights reserved.

  6. Structural study of U(Pd sub 1 sub - sub x Fe sub x) sub 2 Ge sub 2 at high pressure

    CERN Document Server

    Sikolenko, V V; Pomjakushina, E V; Pomjakushin, V Y; Balagurov, A M; Keller, L; Glazkov, V P; Gribanov, A V; Goncharenko, I N; Savenko, B N

    2003-01-01

    The crystal structure of the U(Pd sub 1 sub - sub x Fe sub x) sub 2 Ge sub 2 compounds with Fe content x = 0- 0.03 and the crystal and magnetic structure of U(Pd sub 0 sub . sub 9 sub 8 Fe sub 0 sub . sub 0 sub 2) sub 2 Ge sub 2 at high external pressures up to 4.5 GPa were studied by means of powder neutron diffraction in the temperature range 1.5-300 K. With increasing Fe content the values of the lattice parameters and interatomic distances change only slightly, but it is known from previous experiments that the magnetic structure changes drastically for x >= 0.015. In contrast to this, high external pressure modifies the crystal structure more significantly while the magnetic structure remains unchanged. The results obtained allow one to infer that drastic changes in the magnetic structure of the U(Pd sub 1 sub - sub x Fe sub x) sub 2 Ge sub 2 compounds with increasing Fe content are a consequence of modification of the RKKY-type (RKKY standing for Ruderman, Kittel, Kasuya and Yosida) indirect exchange in...

  7. High Pressure EVA Glove (HPEG), Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Final Frontier Design's (FFD) High Pressure EVA Glove (HPEG) is a game changing technology enabling future exploration class space missions. The high operating...

  8. CARS Diagnostics of High Pressure Combustion.

    Science.gov (United States)

    1982-11-01

    e) 8. CONTRACT OR GRANT NUMBER(e) J. H. Stufflebeam t JDAAG29- 79-C-0008J %A,, Shirley R,,. Hall 9. PERFORMING ORGANIZATION NAME AND ADDRESS 10...also the work in N2 at elevated tem- perature up to 30 atmospheres. John H. Stufflebeam continued the high pressure CARS work under the contract...Spectroscopy, Bordeaux, France, September 1982. 12. J. H. Stufflebeam , J. F. Verdieck, and R. J. Hall: CARS Diagnostics of High Pressure and

  9. High-pressure portable pneumatic drive unit.

    Science.gov (United States)

    Hete, B F; Savage, M; Batur, C; Smith, W A; Golding, L A; Nosé, Y

    1989-12-01

    The left ventricular assist device (LVAD) of the Cleveland Clinic Foundation (CCF) is a single-chamber assist pump, driven by a high-pressure pneumatic cylinder. A low-cost, portable driver that will allow cardiac care patients, with a high-pressure pneumatic ventricle assist, more freedom of movement has been developed. The compact and light-weight configuration can provide periods of 2 h of freedom from a fixed position driver and does not use exotic technology.

  10. Holographic interferometry of high pressure

    International Nuclear Information System (INIS)

    McIlwain, M.E.

    1987-01-01

    Measurements in turbulent flows have been historically performed using various types of probes and optical diagnostic methods. In general, probes suffer from plasma perturbation effects and are single point determination methods. Optical methods appear to be better suited to determinations in turbulent flows, however interpretation of the resulting data can often be complex. Methods such as laser Doppler anemometry, which relies on entrained particles, suffers from the fact that particles small enough to be swept along by the plasma are usually melted or sublimed in the plasma. Light refraction or diffraction methods such as shadow photography, interferometry, and holography have also been used to observe plasma flows. These methods typically suffer from the difficulty of interpreting line of sight images and obtaining quantitative data. A new method based on multi-pass holographic interferometry will be discussed. This method has certain advantages which can significantly simplify the complexity of line of sight interferometry image deconvolution. When the method employs high speed cinematography, time resolved images of the plasma flow can be obtained. This method has been applied to both transferred and non-transferred arcs and various types of DC-plasma torch produced jets. These studies and conclusions as to the usefulness of the technique are presented

  11. Stability of very-high pressure arc discharges against perturbations of the electron temperature

    Energy Technology Data Exchange (ETDEWEB)

    Benilov, M. S. [Departamento de Fisica, Ciencias Exactas e Engenharia, Universidade da Madeira, Largo do Municipio, Funchal 9000 (Portugal); Hechtfischer, U. [Philips Lighting, BU Automotive Lamps, Technology, Philipsstrasse 8, Aachen 52068 (Germany)

    2012-04-01

    We study the stability of the energy balance of the electron gas in very high-pressure plasmas against longitudinal perturbations, using a local dispersion analysis. After deriving a dispersion equation, we apply the model to a very high-pressure (100 bar) xenon plasma and find instability for electron temperatures, T{sub e}, in a window between 2400 K and 5500-7000 K x 10{sup 3} K, depending on the current density (10{sup 6}-10{sup 8} A/m{sup 2}). The instability can be traced back to the Joule heating of the electron gas being a growing function of T{sub e}, which is due to a rising dependence of the electron-atom collision frequency on T{sub e}. We then analyze the T{sub e} range occurring in very high-pressure xenon lamps and conclude that only the near-anode region exhibits T{sub e} sufficiently low for this instability to occur. Indeed, previous experiments have revealed that such lamps develop, under certain conditions, voltage oscillations accompanied by electromagnetic interference, and this instability has been pinned down to the plasma-anode interaction. A relation between the mechanisms of the considered instability and multiple anodic attachments of high-pressure arcs is discussed.

  12. 40 CFR 152.93 - Citation of a previously submitted valid study.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Citation of a previously submitted... Data Submitters' Rights § 152.93 Citation of a previously submitted valid study. An applicant may... the citation is necessary. (b) Study previously submitted by another person. If the applicant is not...

  13. Synthetic chemistry with periodic mesostructures at high pressure.

    Science.gov (United States)

    Mandal, Manik; Landskron, Kai

    2013-11-19

    Over the last two decades, researchers have studied extensively the synthesis of mesostructured materials, which could be useful for drug delivery, catalytic cracking of petroleum, or reinforced plastics, among other applications. However, until very recently researchers used only temperature as a thermodynamic variable for synthesis, completely neglecting pressure. In this Account, we show how pressure can affect the synthetic chemistry of periodic mesoporous structures with desirable effects. In its simplest application, pressure can crystallize the pore walls of periodic mesoporous silicas, which are difficult to crystallize otherwise. The motivation for the synthesis of periodic mesoporous silica materials (with pore sizes from 2 to 50 nm) 20 years ago was to replace the microporous zeolites (which have pore sizes of amorphous nature of the mesoporous materials' channel walls. To address this problem, we developed the concept of "nanocasting at high pressure". Through this approach, we produced hitherto-unavailable, periodic mesostructured silicas with crystalline pore walls. In nanocasting, we compress a periodic mesostructured composite (e.g. a periodic mesoporous silica with carbon-filled pores) and subsequently heat it to induce the selective crystallization of one of the two phases. We attain the necessary high pressure for synthesis using piston-cylinder and multianvil apparatuses. Using periodic mesostructured silica/carbon nanocomposites as starting material, we have produced periodic mesoporous coesite and periodic mesoporous quartz. The quartz material is highly stable under harsh hydrothermal conditions (800°C in pure steam), verifying that crystallinity in the channel walls of periodic mesoporous silicas increases their hydrothermal stability. Even without including the carbon phase in the silica pores, we could obtain mesoporous coesite materials. We found similar behavior for periodic mesoporous carbons, which convert into transparent, mesoporous

  14. Subnanosecond breakdown in high-pressure gases

    Science.gov (United States)

    Naidis, George V.; Tarasenko, Victor F.; Babaeva, Natalia Yu; Lomaev, Mikhail I.

    2018-01-01

    Pulsed discharges in high-pressure gases are of considerable interest as sources of nonequilibrium plasma for various technological applications: pollution control, pumping of laser media, plasma-assisted combustion, etc. Recently, attention has been attracted to the use of subnanosecond voltage fronts, producing diffuse discharges with radii of several millimeters. Such plasma structures, similar to pulsed glow discharges, are of special interest for applications due to quasi-uniformity of plasma parameters in relatively large gas volumes. This review presents the results of experimental and computational study of subnanosecond diffuse discharge formation. A description of generators of short high-voltage pulses with subnanosecond fronts and of discharge setups is given. Diagnostic methods for the measurement of various discharge parameters with high temporal and spatial resolution are described. Obtained experimental data on plasma properties for a wide range of governing factors are discussed. A review of various theoretical approaches used for computational study of the dynamics and structure of fast ionization waves is given; the applicability of conventional fluid streamer models for simulation of subnanosecond ionization waves is discussed. Calculated spatial-temporal profiles of plasma parameters during streamer propagation are presented. The efficiency of subnanosecond discharges for the production of reactive species is evaluated. On the basis of the comparison of simulation results and experimental data the effects of various factors (voltage rise time, polarity, etc.) on discharge characteristics are revealed. The major physical phenomena governing the properties of subnanosecond breakdown are analyzed.

  15. High-pressure hydrogen materials compatibility of piezoelectric films

    Science.gov (United States)

    Alvine, K. J.; Shutthanandan, V.; Bennett, W. D.; Bonham, C. C.; Skorski, D.; Pitman, S. G.; Dahl, M. E.; Henager, C. H.

    2010-11-01

    Hydrogen is well known for materials compatibility issues, including blistering and embrittlement in metals, which are challenges for its use as the next-generation "green" fuel. Beyond metals, hydrogen also degrades piezoelectric materials used as actuators used in direct injection hydrogen internal combustion engines. We present the materials compatibility studies of piezoelectric films in high-pressure hydrogen environments. Absorption of high-pressure hydrogen and composition changes were studied with an elastic recoil detection analysis and Rutherford back-scattering spectrometry in lead zirconate titanate and barium titanate thin films. Hydrogen surface degradation in the form of blistering and Pb mixing was also observed.

  16. A high pressure apparatus for neutron diffraction

    International Nuclear Information System (INIS)

    Kamigaki, Kazuo; Yoshida, Hajime; Ohashi, Masayoshi; Kaneko, Takejiro; Sato, Kozaburo.

    1980-01-01

    A high pressure apparatus was developed for thermal neutron diffraction of time-of-flight method. The high pressure vessel was a piston-cylinder type, and Ti-Zr alloy was used as a material of the cylinder. The coherent scattering of neutron is suppressed in Ti-53wt% Zr alloy. The diffraction spectrum is formed of peaks from the specimen and a background, which corresponds to the energy distribution of the incident neutron. High pressure measurements were made in RbBr on the transformation between NaCl-type structure and CsCl-type to a pressure about 20 kb, and a good agreement was confirmed with former experiments. (author)

  17. Curved and conformal high-pressure vessel

    Science.gov (United States)

    Croteau, Paul F.; Kuczek, Andrzej E.; Zhao, Wenping

    2016-10-25

    A high-pressure vessel is provided. The high-pressure vessel may comprise a first chamber defined at least partially by a first wall, and a second chamber defined at least partially by the first wall. The first chamber and the second chamber may form a curved contour of the high-pressure vessel. A modular tank assembly is also provided, and may comprise a first mid tube having a convex geometry. The first mid tube may be defined by a first inner wall, a curved wall extending from the first inner wall, and a second inner wall extending from the curved wall. The first inner wall may be disposed at an angle relative to the second inner wall. The first mid tube may further be defined by a short curved wall opposite the curved wall and extending from the second inner wall to the first inner wall.

  18. Accessing Mefenamic Acid Form II through High-Pressure Recrystallisation

    Directory of Open Access Journals (Sweden)

    Nasir Abbas

    2017-05-01

    Full Text Available High-pressure crystallisation has been successfully used as an alternative technique to prepare Form II of a non-steroidal anti-inflammatory drug, mefenamic acid (MA. A single crystal of Form II, denoted as high-pressure Form II, was grown at 0.3 GPa from an ethanolic solution by using a diamond anvil cell. A comparison of the crystal structures shows that the efficient packing of molecules in Form II was enabled by the structural flexibility of MA molecules. Compression studies performed on a single crystal of Form I resulted in a 14% decrease of unit cell volume up to 2.5 GPa. No phase transition was observed up to this pressure. A reconstructive phase transition is required to induce conformational changes in the structure, which was confirmed by the results of crystallisation at high pressure.

  19. High pressure water jet cutting and stripping

    Science.gov (United States)

    Hoppe, David T.; Babai, Majid K.

    1991-01-01

    High pressure water cutting techniques have a wide range of applications to the American space effort. Hydroblasting techniques are commonly used during the refurbishment of the reusable solid rocket motors. The process can be controlled to strip a thermal protective ablator without incurring any damage to the painted surface underneath by using a variation of possible parameters. Hydroblasting is a technique which is easily automated. Automation removes personnel from the hostile environment of the high pressure water. Computer controlled robots can perform the same task in a fraction of the time that would be required by manual operation.

  20. Techniques in high pressure neutron scattering

    CERN Document Server

    Klotz, Stefan

    2013-01-01

    Drawing on the author's practical work from the last 20 years, Techniques in High Pressure Neutron Scattering is one of the first books to gather recent methods that allow neutron scattering well beyond 10 GPa. The author shows how neutron scattering has to be adapted to the pressure range and type of measurement.Suitable for both newcomers and experienced high pressure scientists and engineers, the book describes various solutions spanning two to three orders of magnitude in pressure that have emerged in the past three decades. Many engineering concepts are illustrated through examples of rea

  1. High pressure water jet mining machine

    Science.gov (United States)

    Barker, Clark R.

    1981-05-05

    A high pressure water jet mining machine for the longwall mining of coal is described. The machine is generally in the shape of a plowshare and is advanced in the direction in which the coal is cut. The machine has mounted thereon a plurality of nozzle modules each containing a high pressure water jet nozzle disposed to oscillate in a particular plane. The nozzle modules are oriented to cut in vertical and horizontal planes on the leading edge of the machine and the coal so cut is cleaved off by the wedge-shaped body.

  2. High pressure freon decontamination of remote equipment

    International Nuclear Information System (INIS)

    Wilson, C.E.

    1987-01-01

    A series of decontamination tests using high pressure FREON 113 was conducted in the 200 Area of the Hanford site. The intent of these tests was to evaluate the effectiveness of FREON 113 in decontamination of manipulator components, tools, and equipment items contaminated with mixed fission products. The test results indicated that high pressure FREON 113 is very effective in removing fissile material from a variety of objects and can reduce both the quantity and the volume of the radioactive waste material presently being buried

  3. High-pressure test loop design and application

    International Nuclear Information System (INIS)

    Burnette, R.D.; Graves, J.N.; Blair, P.G.; Baldwin, N.L.

    1980-07-01

    A high-pressure test loop (HPTL) has been constructed for the purpose of performing a number of chemistry experiments at simulated HTGR conditions of temperature, pressure, flow, and impurity content. The HPTL can be used to develop, modify, and verify computer codes for a variety of chemical processes involving gas phase transport in the reactor. Processes such as graphite oxidation, fission product transport, fuel reactions, purification systems, and dust entrainment can be studied at high pressure, which would largely eliminate difficulties in correlating existing laboratory data and reactor conditions

  4. High-pressure-low-temperature x-ray power diffractometer.

    Science.gov (United States)

    Syassen, K; Holzapfel, W B

    1978-08-01

    A high-pressure technique for x-ray diffraction studies at low temperatures is described. The system consists of a Bridgman anvil type high-pressure device with either tungsten carbide or boron carbide anvils, a liquid He cryostat, and x-ray diffractometer operating in Debye-Scherrer geometry. The newly developed boron carbide anvil cell is capable of containing a liquid pressure transmitting medium. The precision of the lattice parameter determination is discussed and the effect of nonisostatic stress components on the diffraction pattern is examined.

  5. A high pressure sample facility for neutron scattering

    International Nuclear Information System (INIS)

    Carlile, C.J.; Glossop, B.H.

    1981-06-01

    Commissioning tests involving deformation studies and tests to destruction as well as neutron diffraction measurements of a standard sample have been carried out on the SERC high pressure sample facility for neutron scattering studies. A detailed description of the pressurising equipment is given. (author)

  6. Segmental hair analysis after a single dose of zolpidem: comparison with a previous study.

    Science.gov (United States)

    Cui, Xiaopei; Xiang, Ping; Zhang, Jingshuo; Shi, Yan; Shen, Baohua; Shen, Min

    2013-01-01

    Hair is a useful aid and sometimes even the only matrix in the analytical strategy in drug-facilitated crime (DFC) investigations. In this novel study, segmental hair analysis was performed after a single 10 mg dose of zolpidem was given to 20 Chinese volunteers. Hair was collected 1 month after administration and was analyzed using ultra-high-pressure liquid chromatography/electrospray ionization tandem mass spectrometry. Zolpidem concentrations were found to be in the range of 135.0-554.6 pg/mg in the proximal 0-2 cm segments. These results were markedly different from those reported by Villain et al., who used volunteers administered equal doses of zolpidem. The analytical method used, as well as the volunteers' hair color, inter-individual variations such as metabolic capacity, hair growth rate, drug incorporation rates, physical state of the hair, age, gender, body weight, etc. and diffusion from sweat or other secretions are all factors that should be considered when interpreting the DFC results.

  7. High-pressure oxidation of methane

    NARCIS (Netherlands)

    Hashemi, Hamid; Christensen, Jakob M.; Gersen, Sander; Levinsky, Howard; Klippenstein, Stephen J.; Glarborg, Peter

    2016-01-01

    Methane oxidation at high pressures and intermediate temperatures was investigated in a laminar flow reactor and in a rapid compression machine (RCM). The flow-reactor experiments were conducted at 700–900 K and 100 bar for fuel-air equivalence ratios (Φ) ranging from 0.06 to 19.7, all highly

  8. High pressure metrology for industrial applications

    Science.gov (United States)

    Sabuga, Wladimir; Rabault, Thierry; Wüthrich, Christian; Pražák, Dominik; Chytil, Miroslav; Brouwer, Ludwig; Ahmed, Ahmed D. S.

    2017-12-01

    To meet the needs of industries using high pressure technologies, in traceable, reliable and accurate pressure measurements, a joint research project of the five national metrology institutes and the university was carried out within the European Metrology Research Programme. In particular, finite element methods were established for stress-strain analysis of elastic and nonlinear elastic-plastic deformation, as well as of contact processes in pressure-measuring piston-cylinder assemblies, and high-pressure components at pressures above 1 GPa. New pressure measuring multipliers were developed and characterised, which allow realisation of the pressure scale up to 1.6 GPa. This characterisation is based on research including measurements of material elastic constants by the resonant ultrasound spectroscopy, hardness of materials of high pressure components, density and viscosity of pressure transmitting liquids at pressures up to 1.4 GPa and dimensional measurements on piston-cylinders. A 1.6 GPa pressure system was created for operation of the 1.6 GPa multipliers and calibration of high pressure transducers. A transfer standard for 1.5 GPa pressure range, based on pressure transducers, was built and tested. Herewith, the project developed the capability of measuring pressures up to 1.6 GPa, from which industrial users can calibrate their pressure measurement devices for accurate measurements up to 1.5 GPa.

  9. High Pressure Inactivation of HAV within Mussels

    Science.gov (United States)

    The potential of hepatitis A virus (HAV) to be inactivated within Mediterranean mussels (Mytilus galloprovincialis) and blue mussels (Mytilus edulis) by high pressure processing was evaluated. HAV was bioaccumulated within mussels to approximately 6-log10 PFU by exposure of mussels to HAV-contamina...

  10. High pressure and synchrotron radiation satellite workshop

    International Nuclear Information System (INIS)

    Bass, J.; Guignot, N.; Morard, G.; Mezouar, M.; Andrault, D.; Bolfan-Casanova, N.; Sturhahn, W.; Daniel, I.; Reynard, B.; Simionovici, A.; Sanchez Valle, C.; Martinez, I.; Kantor, I.; Dubrovinsky, I.; Mccammon, C.; Dubrovinskaia, N.; Kurnosiv, A.; Kuznetsov, A.; Goncharenko, I.; Loubeyre, P.; Desgreniers, S.; Weck, G.; Yoo, C.S.; Iota, V.; Park, J.; Cynn, H.; Gorelli, F.; Toulemonde, P.; Machon, D.; Merlen, A.; San Miguel, A.; Amboage, M.; Aquilanti, G.; Mathon, O.; Pascarelli, S.; Itie, J.P.; Mcmillan, P.F.; Trapananti, A.; Di Cicco, A.; Panfilis, S. de; Filipponi, A.; Kreisel, J.; Bouvier, P.; Dkhil, B.; Chaabane, B.; Rosner, H.; Koudela, D.; Schwarz, U.; Handestein, A.; Hanfland, M.; Opahle, I.; Koepernik, K.; Kuzmin, M.; Mueller, K.H.; Mydosh, J.; Richter, M.; Hejny, C.; Falconi, S.; Lundegaard, L.F.; Mcmahon, M.I; Loa, I.; Syassen, K.; Wang, X.; Roth, H.; Lorenz, T.; Farber Daniel, I.; Antonangeli Daniele, I.; Krisch, M.; Badro, J.; Fiquet, G.; Occelli, F.; Mao, W.L.; Mao, H.K.; Eng, P.; Kao, C.C.; Shu, J.F.; Hemley, R.J.; Tse, J.S.; Yao, Y.; Deen, P.P.; Paolasini, I.; Braithwaite, D.; Kernavanois, N.; Lapertot, G.; Rupprecht, K.; Leupold, O.; Ponkratz, U.; Wortmann, G.; Beraud, A.; Krisch, M.; Farber, D.; Antonangeli, D.; Aracne, C.; Zarestky, J.L.; Mcqueeney, R.; Mathon, O.; Baudelet, F.; Decremps, F.; Itie, J.P.; Nataf, I.; Pascarelli, S.; Polian, A.

    2006-01-01

    The workshop is dedicated to recent advances on science at high pressure at third generation synchrotron sources. A variety of experiments using synchrotron radiation techniques including X-ray diffraction, EXAFS (extended X-ray absorption fine structure), inelastic X-ray scattering, Compton scattering and Moessbauer spectroscopy of crystalline, liquid or amorphous samples, are reported. This document gathers the abstracts of the presentations

  11. High Pressure Physics at Brigham Young University

    Science.gov (United States)

    Decker, Daniel

    2000-09-01

    I will discuss the high pressure research of Drs. J. Dean Barnett, Daniel L. Decker and Howard B. Vanfleet of the department of Physics and Astronomy at Brigham Young University and their many graduate students. I will begin by giving a brief history of the beginning of high pressure research at Brigham Young University when H. Tracy Hall came to the University from General Elecrtric Labs. and then follow the work as it progressed from high pressure x-ray diffraction experiments, melting curve measurements under pressure to pressure effects on tracer diffusion and Mossbauer effect spectra. This will be followed by showing the development of pressure calibration techniques from the Decker equation of state of NaCl to the ruby fluorescence spectroscopy and a short discussion of using a liquid cell for hydrostatic measurements and temperature control for precision high pressure measurements. Then I will conclude with a description of thermoelectric measuremnts, critical phenomena at the magnetic Curie point, and the tricritical point of BaTiO_3.

  12. High pressure and synchrotron radiation satellite workshop

    Energy Technology Data Exchange (ETDEWEB)

    Bass, J.; Guignot, N.; Morard, G.; Mezouar, M.; Andrault, D.; Bolfan-Casanova, N.; Sturhahn, W.; Daniel, I.; Reynard, B.; Simionovici, A.; Sanchez Valle, C.; Martinez, I.; Kantor, I.; Dubrovinsky, I.; Mccammon, C.; Dubrovinskaia, N.; Kurnosiv, A.; Kuznetsov, A.; Goncharenko, I.; Loubeyre, P.; Desgreniers, S.; Weck, G.; Yoo, C.S.; Iota, V.; Park, J.; Cynn, H.; Gorelli, F.; Toulemonde, P.; Machon, D.; Merlen, A.; San Miguel, A.; Amboage, M.; Aquilanti, G.; Mathon, O.; Pascarelli, S.; Itie, J.P.; Mcmillan, P.F.; Trapananti, A.; Di Cicco, A.; Panfilis, S. de; Filipponi, A.; Kreisel, J.; Bouvier, P.; Dkhil, B.; Chaabane, B.; Rosner, H.; Koudela, D.; Schwarz, U.; Handestein, A.; Hanfland, M.; Opahle, I.; Koepernik, K.; Kuzmin, M.; Mueller, K.H.; Mydosh, J.; Richter, M.; Hejny, C.; Falconi, S.; Lundegaard, L.F.; Mcmahon, M.I; Loa, I.; Syassen, K.; Wang, X.; Roth, H.; Lorenz, T.; Farber Daniel, I.; Antonangeli Daniele, I.; Krisch, M.; Badro, J.; Fiquet, G.; Occelli, F.; Mao, W.L.; Mao, H.K.; Eng, P.; Kao, C.C.; Shu, J.F.; Hemley, R.J.; Tse, J.S.; Yao, Y.; Deen, P.P.; Paolasini, I.; Braithwaite, D.; Kernavanois, N.; Lapertot, G.; Rupprecht, K.; Leupold, O.; Ponkratz, U.; Wortmann, G.; Beraud, A.; Krisch, M.; Farber, D.; Antonangeli, D.; Aracne, C.; Zarestky, J.L.; Mcqueeney, R.; Mathon, O.; Baudelet, F.; Decremps, F.; Itie, J.P.; Nataf, I.; Pascarelli, S.; Polian, A

    2006-07-01

    The workshop is dedicated to recent advances on science at high pressure at third generation synchrotron sources. A variety of experiments using synchrotron radiation techniques including X-ray diffraction, EXAFS (extended X-ray absorption fine structure), inelastic X-ray scattering, Compton scattering and Moessbauer spectroscopy of crystalline, liquid or amorphous samples, are reported. This document gathers the abstracts of the presentations.

  13. High pressure synthesis of bismuth disulfide

    DEFF Research Database (Denmark)

    Søndergaard-Pedersen, Simone; Nielsen, Morten Bormann; Bremholm, Martin

    In this research the BiS2 compound was synthesized by a high pressure and high temperature method using a multi-anvil large volume press and the structure was solved by single crystal diffraction. The structure contains Bi atoms in distorted square-based pyramidal coordination to five surrounding...

  14. The Birmingham experience of high-pressure methylene blue dye test during primary and revisional bariatric surgery: A retrospective cohort study

    Directory of Open Access Journals (Sweden)

    G.C. Kirby

    2017-11-01

    Conclusion: Despite routine use of methylene blue dye test in 924 patients, there were only two positive tests. Whilst HPMB may demonstrate technical failure, this study suggests that there is no role for its routine use in primary bariatric surgery. Discontinuation of this practice would reduce risk of anaphylaxis to the dye, cost, and intra-operative time.

  15. Elastic properties of Fe-bearing wadsleyite at high pressures

    Science.gov (United States)

    Mao, Z.; Jacobsen, S. D.; Jiang, F.; Smyth, J. R.; Holl, C. M.; Frost, D. J.; Duffy, T.

    2009-12-01

    The elastic properties of wadsleyite, thought to be the dominant phase from 410 to 520-km depth in the mantle, are essential to interpret the seismic images and profiles in the transition zone. Our previous experimental measurements showed that elasticity of Mg2SiO4 wadsleyite can be significantly reduced by hydration at high pressures (e.g. Mao et al., 2008a,b). These results provide the first constraints on the effect of hydration on the high-pressure sound velocities of wadsleyite, and are significantly important for identifying the potential hydrogen rich region in the Earth’s transition zone. Since mantle wadsleyite contains ~10 mol.% Fe, it is more important to investigate the combined effect of Fe and hydration on the elastic properties of wadsleyite. Here, we measured the single-crystal elasticity of wadsleyite with 1.0 wt.% H2O, Mg1.73Fe0.19SiO4H0.16, up to 12 GPa using Brillouin scattering. At ambient conditions, the aggregate bulk modulus, KS0, and shear modulus, G0, are 158.4(5) GPa and 99.2(3) GPa, respectively. Including the results of current and previous studies, we find that the elasticity of wadsleyite decreases linearly with Fe and H2O content according to relations (in GPa): KS0 = 171(3)-13.0(8)CH2O, G0 = 112(2)-8.8(3)CH2O-40(10)XFe, where CH2O is the concentration of hydrogen expressed as weight percent H2O, and XFe is the Fe molar fraction (XFe = Fe/(Mg+Fe)). Further high-pressure measurements showed that the presence of 1 wt.% H2O in Fe-bearing wadsleyite increases the pressure derivative of the shear modulus from 1.5(1) to 1.9(1). But Fe-bearing wadsleyite with this amount of H2O might have a similar pressure derivative of the bulk modulus (4.8(1)) similar to the corresponding anhydrous phase. Using our results, we computed the sound velocities of wadsleyite with 1 wt.% H2O up to 12 GPa at 300 K. Compared to Fe-bearing anhydrous wadsleyite, 1 wt.% H2O causes a 1.5(4)% reduction in the compressional velocity at 12 GPa, and a 1

  16. Advanced Diagnostics for High Pressure Spray Combustion.

    Energy Technology Data Exchange (ETDEWEB)

    Skeen, Scott A.; Manin, Julien Luc; Pickett, Lyle M.

    2014-06-01

    The development of accurate predictive engine simulations requires experimental data to both inform and validate the models, but very limited information is presently available about the chemical structure of high pressure spray flames under engine- relevant conditions. Probing such flames for chemical information using non- intrusive optical methods or intrusive sampling techniques, however, is challenging because of the physical and optical harshness of the environment. This work details two new diagnostics that have been developed and deployed to obtain quantitative species concentrations and soot volume fractions from a high-pressure combusting spray. A high-speed, high-pressure sampling system was developed to extract gaseous species (including soot precursor species) from within the flame for offline analysis by time-of-flight mass spectrometry. A high-speed multi-wavelength optical extinction diagnostic was also developed to quantify transient and quasi-steady soot processes. High-pressure sampling and offline characterization of gas-phase species formed following the pre-burn event was accomplished as well as characterization of gas-phase species present in the lift-off region of a high-pressure n-dodecane spray flame. For the initial samples discussed in this work several species were identified, including polycyclic aromatic hydrocarbons (PAH); however, quantitative mole fractions were not determined. Nevertheless, the diagnostic developed here does have this capability. Quantitative, time-resolved measurements of soot extinction were also accomplished and the novel use of multiple incident wavelengths proved valuable toward characterizing changes in soot optical properties within different regions of the spray flame.

  17. Effect of high pressurized carbon dioxide on Escherichia coli ...

    African Journals Online (AJOL)

    Carbon dioxide at high pressure can retard microbial growth and sometimes kill microorganisms depending on values of applied pressure, temperature and exposure time. In this study the effect of high pressurised carbon dioxide (HPCD) on Escherichia coli was investigated. Culture of E. coli was subjected to high ...

  18. Correlation between non-Fermi-liquid behavior and superconductivity in (Ca, La)(Fe,Co)As2 iron arsenides: A high-pressure study

    Science.gov (United States)

    Zhou, W.; Ke, F.; Xu, Xiaofeng; Sankar, R.; Xing, X.; Xu, C. Q.; Jiang, X. F.; Qian, B.; Zhou, N.; Zhang, Y.; Xu, M.; Li, B.; Chen, B.; Shi, Z. X.

    2017-11-01

    Non-Fermi-liquid (NFL) phenomena associated with correlation effects have been widely observed in the phase diagrams of unconventional superconducting families. Exploration of the correlation between the normal state NFL, regardless of its microscopic origins, and the superconductivity has been argued as a key to unveiling the mystery of the high-Tc pairing mechanism. Here we systematically investigate the pressure-dependent in-plane resistivity (ρ ) and Hall coefficient (RH) of a high-quality 112-type Fe-based superconductor Ca1 -xLaxFe1 -yCoyAs2 (x =0.2 ,y =0.02 ). With increasing pressure, the normal-state resistivity of the studied sample exhibits a pronounced crossover from non-Fermi-liquid to Fermi-liquid behaviors. Accompanied with this crossover, Tc is gradually suppressed. In parallel, the extremum in the Hall coefficient RH(T ) curve, possibly due to anisotropic scattering induced by spin fluctuations, is also gradually suppressed. The symbiosis of NFL and superconductivity implies that these two phenomena are intimately related. Further study on the pressure-dependent upper critical field reveals that the two-band effects are also gradually weakened with increasing pressure and reduced to the one-band Werthamer-Helfand-Hohenberg limit in the low-Tc regime. Overall, our paper supports the picture that NFL, multigap, and extreme RH(T ) are all of the same magnetic origin, i.e., the spin fluctuations in the 112 iron arsenide superconductors.

  19. An unconventional metallic state in YbRh sub 2 (Si sub 1 sub - sub x Ge sub x) sub 2 - a high pressure study

    CERN Document Server

    Mederle, S; Geibel, C; Grosche, F M; Sparn, G; Trovarelli, O; Steglich, F

    2002-01-01

    We present a detailed pressure study of the electrical resistivity rho(T) and the specific heat C(T) of the non-Fermi-liquid (NFL) compound YbRh sub 2 Si sub 2 and of rho(T) for a single crystal in which 5 at.% of Si is replaced by isoelectronic Ge. The magnetic phase diagram is deduced up to p approx = 2.5 GPa. A comparison of the effects of the volume change introduced by doping and/or by hydrostatic pressure will be given. We show that the NFL behaviour observed in rho(T) as well as the magnetic phase diagram are not influenced by the disorder introduced by alloying.

  20. In situ high pressure and high temperature Raman studies of (1-x)SiO{sub 2}xGeO{sub 2} glasses

    Energy Technology Data Exchange (ETDEWEB)

    Le Parc, R; Levelut, C; Clement, S [Laboratoire des Colloides Verres et Nanomateriaux, UMR CNRS-UM2 5587, Universite Montpellier 2, Place Eugene Bataillon, 34095 Montpellier Cedex 5 (France); Ranieri, V; Haines, J; Cambon, M; Cambon, O [Institut Charles Gerhardt Montpellier, Equipe PMOF, UMR CNRS-UM2 5253, Universite Montpellier 2, Place Eugene Bataillon, 34095 Montpellier Cedex 5 (France)

    2009-09-16

    The structure of glasses in the binary system SiO{sub 2}-GeO{sub 2} has been studied by Raman spectroscopy. Our results are consistent with mixing of SiO{sub 2} and GeO{sub 2} tetrahedra. The changes induced by temperature and by pressure on the structure are monitored by in situ measurements on the same mixed glasses. Anomalous temperature dependences are observed not only for SiO{sub 2} glass and GeO{sub 2} glass but also for mixed glasses. Particular attention is focused on the pressure densification mechanism in mixed glasses. Via the pressure dependence of the width of the main Raman band, we show that the compression mechanism in mixed glasses is intermediate between that of the end members.

  1. Oxygen Buffering in High Pressure Solid Media Assemblies: New Approach Enabling Study of fO2 from IW-4 to IW+4.5

    Science.gov (United States)

    Righter, K.; Pando, K. M.; Ross, D. K.; Butterworth, A. L.; Gainsforth, Z.; Jilly-Rehak, C. E.; Westphal, A. J.

    2017-01-01

    Oxygen fugacity is an intensive parameter that controls some fundamental chemical and physical properties in planetary materials. In terrestrial magmas high fO2 promotes magnetite stability and low fO2 causes Fe-enrichment due to magnetite suppression. In lunar and asteroidal basalts, low fO2 can allow metal to be stable. Experimental studies will therefore be most useful if they are done at a specific and relevant fO2 for the samples under consideration. Control of fO2 in the solid media apparatus (piston cylinder multi-anvil) has relied on either sliding sensors or graphite capsule buffering, which are of limited application to the wide range of fO2 recorded in planetary or astromaterials. Here we describe a new approach that allows fO2 to be specified across a wide range of values relevant to natural samples.

  2. Neutron Diffraction Study of the High-Tc Superconductor HgBa2CaCu2O6.3 under High Pressure

    International Nuclear Information System (INIS)

    Aksenov, V.L.; Balagurov, A.M.; Savenko, B.N.; Capponi, J.J.; Glazkov, V.P.; Goncharenko, I.N.; Somenkov, V.A.

    1994-01-01

    The pressure dependence of the crystal structure of a powder sample of HgBa 2 CaCu 2 O 6.3 (T c =123 K) was studied in the pressure range of 0 to 3.6 GPa, using the DN-12 time-of-flight diffractometer at the IBR-2 pulsed reactor and a sapphire anvil cell chamber. At P=0 the results are in a good accordance with the published data. At P=3.0 and 3.6 GPa the best fit of the experimental data was achieved using the structural model with apical oxygen disordered in the (a,b) plane. The compressibility values of the lattice constants and selected bonds were calculated from the structural data. The highest absolute value of compressibility was found for the distance between the O atom layers. 12 refs., 6 figs., 3 tabs

  3. High-pressure applications in medicine and pharmacology

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Jerson L; Foguel, Debora; Suarez, Marisa; Gomes, Andre M O; Oliveira, Andrea C [Centro Nacional de Ressonancia Magnetica Nuclear, Departamento de Bioquimica Medica, Instituto de Ciencias Biomedicas, Universidade Federal do Rio de Janeiro, Rio de Janeiro, RJ 21941-590 (Brazil)

    2004-04-14

    High pressure has emerged as an important tool to tackle several problems in medicine and biotechnology. Misfolded proteins, aggregates and amyloids have been studied, which point toward the understanding of the protein misfolding diseases. High hydrostatic pressure (HHP) has also been used to dissociate non-amyloid aggregates and inclusion bodies. The diverse range of diseases that result from protein misfolding has made this theme an important research focus for pharmaceutical and biotech companies. The use of high pressure promises to contribute to identifying the mechanisms behind these defects and creating therapies against these diseases. High pressure has also been used to study viruses and other infectious agents for the purpose of sterilization and in the development of vaccines. Using pressure, we have detected the presence of a ribonucleoprotein intermediate, where the coat protein is partially unfolded but bound to RNA. These intermediates are potential targets for antiviral compounds. The ability of pressure to inactivate viruses, prions and bacteria has been evaluated with a view toward the applications of vaccine development and virus sterilization. Recent studies demonstrate that pressure causes virus inactivation while preserving the immunogenic properties. There is increasing evidence that a high-pressure cycle traps a virus in the 'fusion intermediate state', not infectious but highly immunogenic.

  4. Feasibility of generating a useful laser-induced breakdown spectroscopy plasma on rocks at high pressure: preliminary study for a Venus mission

    International Nuclear Information System (INIS)

    Arp, Zane A.; Cremers, David A.; Harris, Ronny D.; Oschwald, David M.; Parker, Gary R.; Wayne, David M.

    2004-01-01

    Laser-induced breakdown spectroscopy (LIBS) is being developed for future use on landers and rovers to Mars. The method also has potential for use on probes to other planets, the Moon, asteroids and comets. Like Mars, Venus is of strong interest because of its proximity to earth, but unlike Mars, conditions at the surface are far more hostile with temperatures in excess of 700 K and pressures on the order of 9.1 MPa (90 atm). These conditions present a significant challenge to spacecraft design and demand that rapid methods of chemical data gathering be implemented. The advantages of LIBS (e.g. stand-off and very rapid analysis) make the method particularly attractive for Venus exploration because of the expected short operational lifetimes (∼2 h) of surface instrumentation. Although the high temperature of Venus should pose no problem to the analytical capabilities of the LIBS spark, the demonstrated strong dependence of laser plasma characteristics on ambient gas pressures below earth atmospheric pressure requires that LIBS measurements be evaluated at the high Venus surface pressures. Here, we present a preliminary investigation of LIBS at 9.1 MPa for application to the analysis of a basalt rock sample. The results suggest the feasibility of the method for a Venus surface probe and that further study is justified

  5. High-pressure x-ray diffraction studies of the nanostructured transparent vitroceramic medium K2O-SiO2-Ga2O3

    International Nuclear Information System (INIS)

    Lipinska-Kalita, K.E.; Chen, B.; Kruger, M.B.; Ohki, Y.; Murowchick, J.; Gogol, E.P.

    2003-01-01

    Synchrotron-radiation-based, energy-dispersive x-ray-diffraction studies have been performed on a composite containing nanometer-size aggregates embedded in an amorphous matrix, in the pressure range from ambient up to 15 GPa. The optically transparent material containing β-Ga 2 O 3 nanocrystals was developed by the controlled crystallization of a silicon oxide-based amorphous precursor. Transmission electron microscopy and conventional x-ray-diffraction techniques allowed estimating the mean size of a single-crystalline phase to be 14.8±1.9 nm, distributed homogeneously in an amorphous medium. The pressure-driven evolution of x-ray-diffraction patterns indicated a progressive densification of the nanocrystalline phase. A structural modification corresponding to a pressure-induced coordination change of the gallium atoms was evidenced by the appearance of new diffraction peaks. The overall changes of x-ray-diffraction patterns indicated a β-Ga 2 O 3 to α-Ga 2 O 3 phase transformation. The low- to high-density phase transition was initiated at around 6 GPa and not completed in the pressure range investigated. A Birch-Murnaghan fit of the unit-cell volume change as a function of pressure yielded a zero-pressure bulk modulus, K 0 , for the nanocrystalline phase of 191±4.9 GPa and its pressure derivative, K 0 ' =8.3±0.9

  6. Vacancy-induced initial decomposition of condensed phase NTO via bimolecular hydrogen transfer mechanisms at high pressure: a DFT-D study.

    Science.gov (United States)

    Liu, Zhichao; Wu, Qiong; Zhu, Weihua; Xiao, Heming

    2015-04-28

    Density functional theory with dispersion-correction (DFT-D) was employed to study the effects of vacancy and pressure on the structure and initial decomposition of crystalline 5-nitro-2,4-dihydro-3H-1,2,4-triazol-3-one (β-NTO), a high-energy insensitive explosive. A comparative analysis of the chemical behaviors of NTO in the ideal bulk crystal and vacancy-containing crystals under applied hydrostatic compression was considered. Our calculated formation energy, vacancy interaction energy, electron density difference, and frontier orbitals reveal that the stability of NTO can be effectively manipulated by changing the molecular environment. Bimolecular hydrogen transfer is suggested to be a potential initial chemical reaction in the vacancy-containing NTO solid at 50 GPa, which is prior to the C-NO2 bond dissociation as its initiation decomposition in the gas phase. The vacancy defects introduced into the ideal bulk NTO crystal can produce a localized site, where the initiation decomposition is preferentially accelerated and then promotes further decompositions. Our results may shed some light on the influence of the molecular environments on the initial pathways in molecular explosives.

  7. High-pressure study of Ti{sub 50}Ni{sub 25}Fe{sub 25} powder produced by mechanical alloying

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, A. S. [Departamento de Engenharia Mecânica, Universidade Federal de Santa Catarina, CP 476 Florianópolis, Santa Catarina 88040-900 (Brazil); Rovani, P. R. [Instituto de Física, Universidade Federal do Rio Grande do Sul, Porto Alegre, Rio Grande do Sul 91501-970 (Brazil); Lima, J. C. de, E-mail: joao.cardoso.lima@ufsc.br [Departamento de Física, Universidade Federal de Santa Catarina, CP 476 Florianópolis, 88040-900 Santa Catarina (Brazil); Pereira, A. S. [Instituto de Física, Universidade Federal do Rio Grande do Sul, Porto Alegre, Rio Grande do Sul 91501-970 (Brazil); Departamento de Materiais, Escola de Engenharia, Universidade Federal do Rio Grande do Sul, Porto Alegre, Rio Grande do Sul 91501-970 (Brazil)

    2015-02-21

    A nanostructured Ti{sub 50}Ni{sub 25}Fe{sub 25} phase (B2) was formed by mechanical alloying and its structural stability was studied as a function of pressure. The changes were followed by X-ray diffraction. The B2 phase was observed up to 7 GPa; for larger pressures, the B2 phase transformed into a trigonal/hexagonal phase (B19) that was observed up to the highest pressure used (18 GPa). Besides B2 and B19, elemental Ni or a SS-(Fe,Ni) and FeNi{sub 3} were observed. With decompression, the B2 phase was recovered. Using in situ angle-dispersive X-ray diffraction patterns, the single line method was applied to obtain the apparent crystallite size and the microstrain for both the B2 and the B19 phases as a function of the applied pressure. Values of the bulk modulus for the B2, B19, elemental Ni or SS-(Fe,Ni) and FeNi{sub 3} phases were obtained by fitting the pressure dependence of the volume to a Birch–Murnaghan equation of state (BMEOS)

  8. Phosphorus Dimerization in Gallium Phosphide at High Pressure

    Energy Technology Data Exchange (ETDEWEB)

    Lavina, Barbara [High Pressure Science and Engineering Center, University of Nevada, Las Vegas, Nevada 89154, United States; Department of Physics and Astronomy, University of Nevada, Las Vegas, Nevada 89154, United States; Kim, Eunja [Department of Physics and Astronomy, University of Nevada, Las Vegas, Nevada 89154, United States; Cynn, Hyunchae [Lawrence Livermore National Laboratory, Livermore, California 94550, United States; Weck, Philippe F. [Sandia National Laboratories, Albuquerque, New Mexico 87185, United States; Seaborg, Kelly [High Pressure Science and Engineering Center, University of Nevada, Las Vegas, Nevada 89154, United States; Department of Physics and Astronomy, University of Nevada, Las Vegas, Nevada 89154, United States; Siska, Emily [High Pressure Science and Engineering Center, University of Nevada, Las Vegas, Nevada 89154, United States; Meng, Yue [HPCAT, Carnegie Institution of Washington, Argonne, Illinois 60439, United States; Evans, William [Lawrence Livermore National Laboratory, Livermore, California 94550, United States

    2018-02-09

    Using combined experimental and computational approaches, we show that at 43 GPa and 1300 K gallium phosphide adopts the super-Cmcm structure, here indicated with its Pearson notation oS24. First-principles enthalpy calculations demonstrate that this structure is more thermodynamically stable above ~20 GPa than previously proposed polymorphs. Here, in contrast to other polymorphs, the oS24 phase shows a strong bonding differentiation and distorted fivefold coordination geometries of both P atoms. The shortest bond of the phase is a single covalent P–P bond measuring 2.171(11) Å at synthesis pressure. Phosphorus dimerization in GaP sheds light on the nature of the super-Cmcm phase and provides critical new insights into the high-pressure polymorphism of octet semiconductors. Bond directionality and anisotropy explain the relatively low symmetry of this high-pressure phase.

  9. Summary of Previous Chamber or Controlled Anthrax Studies and Recommendations for Possible Additional Studies

    Energy Technology Data Exchange (ETDEWEB)

    Piepel, Gregory F.; Amidan, Brett G.; Morrow, Jayne B.

    2010-12-29

    This report and an associated Excel file(a) summarizes the investigations and results of previous chamber and controlled studies(b) to characterize the performance of methods for collecting, storing and/or transporting, extracting, and analyzing samples from surfaces contaminated by Bacillus anthracis (BA) or related simulants. This report and the Excel are the joint work of the Pacific Northwest National Laboratory (PNNL) and the National Institute of Standards and Technology (NIST) for the Department of Homeland Security, Science and Technology Directorate. The report was originally released as PNNL-SA-69338, Rev. 0 in November 2009 with limited distribution, but was subsequently cleared for release with unlimited distribution in this Rev. 1. Only minor changes were made to Rev. 0 to yield Rev. 1. A more substantial update (including summarizing data from other studies and more condensed summary tables of data) is underway

  10. A high-pressure study of phase stability in La sub 0 sub . sub 5 sub - sub x Bi sub x Ca sub 0 sub . sub 5 MnO sub 3 by energy-dispersive x-ray diffraction

    CERN Document Server

    Wang Xin; Pan Yue Wu; Zou Guang Tian

    2002-01-01

    Energy-dispersive x-ray diffraction studies are carried out on the distorted perovskite La sub 0 sub . sub 5 sub - sub x Bi sub x Ca sub 0 sub . sub 5 MnO sub 3 (x = 0, 0.05, 0.1, 0.15, 0.2, 0.25) under high pressure at room temperature. The unusual expansion of the 202-040 d-spacing under pressure is observed, and the change of the Mn-O bond angle brings about the disappearance of the basal-plane Q sub 2 distortion mode. With doping content increasing, a shoulder peak appears in the observed main peak of La sub 0 sub . sub 2 sub 5 Bi sub 0 sub . sub 2 sub 5 Ca sub 0 sub . sub 5 MnO sub 3 at 43.9 GPa. The pressure-enhanced interactions between charge, orbital, and coupling with the lattice distortion are discussed.

  11. High-pressure and temperature investigations of energetic materials

    Science.gov (United States)

    Gump, J. C.

    2014-05-01

    Static high-pressure measurements are extremely useful for obtaining thermodynamic and phase stability information from a wide variety of materials. However, studying energetic materials can be challenging when extracting information from static high-pressure measurements. Energetic materials are traditionally C, H, N, O compounds with low crystalline symmetry, producing weak signal in commonly performed x-ray diffraction measurements. The small sample volume available in a static high-pressure cell exacerbates this issue. Additionally, typical hydrostatic compression media, such as methanol/ethanol, may react with many energetic materials. However, characterization of their thermodynamic parameters and phase stability is critical to understanding explosive performance and sensitivity. Crystalline properties, such as bulk modulus and thermal expansion, are necessary to accurately predict the behaviour of shocked solids using hydrodynamic codes. In order to obtain these values, equations of state of various energetic materials were investigated using synchrotron angle-dispersive x-ray diffraction experiments at static high-pressure and temperature. Intense synchrotron radiation overcomes the weak x-ray scattering of energetic materials in a pressure cell. The samples were hydrostatically compressed using a non-reactive hydrostatic medium and heated using a heated diamond anvil cell. Pressure - volume data for the materials were fit to the Birch-Murnaghan and Vinet formalisms to obtain bulk modulus and its first pressure derivative. Temperature - volume data at ambient pressure were fit to obtain the volume thermal expansion coefficient. Data from several energetic materials will be presented and compared.

  12. High-pressure oxidation of methane

    DEFF Research Database (Denmark)

    Hashemi, Hamid; Christensen, Jakob Munkholt; Gersen, Sander

    2016-01-01

    Methane oxidation at high pressures and intermediate temperatures was investigated in a laminar flow reactor and in a rapid compression machine (RCM). The flow-reactor experiments were conducted at 700–900 K and 100 bar for fuel-air equivalence ratios (Φ) ranging from 0.06 to 19.7, all highly...... diluted in nitrogen. It was found that under the investigated conditions, the onset temperature for methane oxidation ranged from 723 K under reducing conditions to 750 K under stoichiometric and oxidizing conditions. The RCM experiments were carried out at pressures of 15–80 bar and temperatures of 800......–1250 K under stoichiometric and fuel-lean (Φ=0.5) conditions. Ignition delays, in the range of 1–100 ms, decreased monotonically with increasing pressure and temperature. A chemical kinetic model for high-pressure methane oxidation was established, with particular emphasis on the peroxide chemistry...

  13. High Pressure Multicomponent Adsorption in Porous Media

    DEFF Research Database (Denmark)

    Shapiro, Alexander; Stenby, Erling Halfdan

    1999-01-01

    We analyse adsorption of a multicomponent mixture at high pressure on the basis of the potential theory of adsorption. The adsorbate is considered as a segregated mixture in the external field produced by a solid adsorbent. we derive an analytical equation for the thickness of a multicomponent film...... close to a dew point. This equation (asymptotic adsorption equation, AAE) is a first order approximation with regard to the distance from a phase envelope....

  14. High pressure neutron powder diffraction at LANSCE

    International Nuclear Information System (INIS)

    Von Dreele, R.B.

    1994-01-01

    By making use of the recently developed ''Paris-Edinburgh'' high pressure cell, the author has successfully performed neutron powder experiments to 10GPa at ambient temperature. Results for the structural compression of the high Tc 1223-Hg superconductor to 9.2 GPa, the compression and possible hydrogen bond formation in brucite, Mg(OD) 2 , to 9.3 GPa, and the molecular reorientation in nitromethane to 5.5 GPa will be presented

  15. Path Dependency of High Pressure Phase Transformations

    Science.gov (United States)

    Cerreta, Ellen

    2017-06-01

    At high pressures titanium and zirconium are known to undergo a phase transformation from the hexagonal close packed (HCP), alpha-phase to the simple-hexagonal, omega-phase. Under conditions of shock loading, the high-pressure omega-phase can be retained upon release. It has been shown that temperature, peak shock stress, and texture can influence the transformation. Moreover, under these same loading conditions, plastic processes of slip and twinning are also affected by similar differences in the loading path. To understand this path dependency, in-situ velocimetry measurements along with post-mortem metallographic and neutron diffraction characterization of soft recovered specimens have been utilized to qualitatively understand the kinetics of transformation, quantify volume fraction of retained omega-phase and characterize the shocked alpha and omega-phases. Together the work described here can be utilized to map the non-equilibrium phase diagram for these metals and lend insight into the partitioning of plastic processes between phases during high pressure transformation. In collaboration with: Frank Addesssio, Curt Bronkhorst, Donald Brown, David Jones, Turab Lookman, Benjamin Morrow, Carl Trujillo, Los Alamos National Lab.; Juan Pablo Escobedo-Diaz, University of New South Wales; Paulo Rigg, Washington State University.

  16. A standardized technique for high-pressure cooling of protein crystals.

    Science.gov (United States)

    Quirnheim Pais, David; Rathmann, Barbara; Koepke, Juergen; Tomova, Cveta; Wurzinger, Paul; Thielmann, Yvonne

    2017-12-01

    Cryogenic temperatures slow down secondary radiation damage during data collection from macromolecular crystals. In 1973, cooling at high pressure was identified as a method for cryopreserving crystals in their mother liquor [Thomanek et al. (1973). Acta Cryst. A29, 263-265]. Results from different groups studying different crystal systems indicated that the approach had merit, although difficulties in making the process work have limited its widespread use. Therefore, a simplified and reliable technique has been developed termed high-pressure cooling (HPC). An essential requirement for HPC is to protect crystals in capillaries. These capillaries form part of new sample holders with SPINE standard dimensions. Crystals are harvested with the capillary, cooled at high pressure (220 MPa) and stored in a cryovial. This system also allows the usage of the standard automation at the synchrotron. Crystals of hen egg-white lysozyme and concanavalin A have been successfully cryopreserved and yielded data sets to resolutions of 1.45 and 1.35 Å, respectively. Extensive work has been performed to define the useful working range of HPC in capillaries with 250 µm inner diameter. Three different 96-well crystallization screens that are most frequently used in our crystallization facility were chosen to study the formation of amorphous ice in this cooling setup. More than 89% of the screening solutions were directly suitable for HPC. This achievement represents a drastic improvement for crystals that suffered from cryoprotection or were not previously eligible for cryoprotection.

  17. 7 CFR 58.219 - High pressure pumps and lines.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false High pressure pumps and lines. 58.219 Section 58.219....219 High pressure pumps and lines. High pressure lines may be cleaned-in-place and shall be of such construction that dead ends, valves and the high pressure pumps can be disassembled for hand cleaning. The high...

  18. Pyridinium salt investigations under high pressure: pressure-induced phase transitions in ferroelectric pyridinium perrhenate

    International Nuclear Information System (INIS)

    Czarnecki, P; Beskrovny, A I; Bobrowicz-Sarga, L; Lewicki, S; Wasicki, J

    2005-01-01

    The properties of pyridinium perrhenate have been studied by three methods: dielectric spectroscopy, neutron powder diffractometry and NMR spectrometry under high pressure. It has been shown that under high pressure the temperatures of the two phase transitions in the crystal are shifted towards lower ones. Moreover, the results have shown the occurrence of a new high pressure phase with a triple point corresponding to the pressure of 100 MPa and the temperature of 240 K

  19. Calculation of high-pressure argon plasma parameters produced by excimer laser

    International Nuclear Information System (INIS)

    Tsuda, Norio; Yamada, Jun

    2000-01-01

    When a XeCl excimer laser light was focused in a high-pressure argon gas up to 150 atm, a dense plasma developed not only backward but also forward. It is important to study on the electron density and temperature of the laser-induced plasma in the high-pressure gas. The electron density and temperature in high-pressure argon plasma produced by XeCl excimer laser has been calculated and compared with the experimental data. (author)

  20. Characterization of high-pressure RTM processes for manufacturing of high performance composites

    OpenAIRE

    Chaudhari, R.; Karcher, M.; Elsner, P.; Henning, F.

    2012-01-01

    The current paper addresses new variants of the RTM process namely High Pressure-Injection Resin Transfer Molding (HP-IRTM) and High Pressure - Compression Resin Transfer Molding (HP-CRTM) for manufacturing of continuous fiber reinforced composites with high fiber volume content. Both these process utilize High Pressure RTM equipment for precise dosing and mixing of highly reactive epoxy resin and amine hardener with relatively high throughput rates. The objective of the proposed study was to...

  1. Identification of multidrug resistance in previously treated tuberculosis patients: a mixed methods study in Cambodia

    Science.gov (United States)

    Royce, S; Khann, S; Yadav, RP; Mao, ET; Cattamanchi, A; Sam, S; Handley, MA

    2014-01-01

    SUMMARY Setting Previously treated tuberculosis (TB) patients are a priority for drug susceptibility testing (DST) to identify cases with multidrug resistance (MDR). In Cambodia, a recent study found that only one-third of smear-positive previously treated patients had DST results. Objective To quantify the gaps in detecting MDR in previously treated TB patients in Cambodia, and describe health workers’ perspectives on barriers, facilitators and potential interventions. Design We analyzed case notifications in Cambodia (2004–2012) and conducted semi-structured interviews with key stakeholders Results The proportion of previously treated notifications varied significantly across provinces 2010–12, in the context of longer term trends of decreasing relapse and increasing “other” retreatment notifications. Correct classification of patients’ TB treatment history and ensuring specimens from previously-treated patients are collected and reach the laboratory could nearly double the number of detected MDR-TB cases. Identified barriers include patients’ reluctance to disclose and staff difficulty eliciting treatment history, partly due to availability of streptomycin only in hospitals. Facilitators include trained health workers, collection of sputum for DST even if previously treated patients are not taking streptomycin, streamlining sputum transportation and promptly reporting results. Conclusion Improved monitoring, supportive supervision, and correctly classifying previously treated patients are essential for improving detection of MDR-TB. PMID:25299861

  2. Matched cohort study of external cephalic version in women with previous cesarean delivery.

    Science.gov (United States)

    Keepanasseril, Anish; Anand, Keerthana; Soundara Raghavan, Subrahmanian

    2017-07-01

    To evaluate the efficacy and safety of external cephalic version (ECV) among women with previous cesarean delivery. A retrospective study was conducted using data for women with previous cesarean delivery and breech presentation who underwent ECV at or after 36 weeks of pregnancy during 2011-2016. For every case, two multiparous women without previous cesarean delivery who underwent ECV and were matched for age and pregnancy duration were included. Characteristics and outcomes were compared between groups. ECV was successful for 32 (84.2%) of 38 women with previous cesarean delivery and 62 (81.6%) in the control group (P=0.728). Multivariate regression analysis confirmed that previous cesarean was not associated with ECV success (odds ratio 1.89, 95% confidence interval 0.19-18.47; P=0.244). Successful vaginal delivery after successful ECV was reported for 19 (59.4%) women in the previous cesarean delivery group and 52 (83.9%) in the control group (Pcesarean delivery. To avoid a repeat cesarean delivery, ECV can be offered to women with breech presentation and previous cesarean delivery who are otherwise eligible for a trial of labor. © 2017 International Federation of Gynecology and Obstetrics.

  3. Simulation of plasma loading of high-pressure RF cavities

    Energy Technology Data Exchange (ETDEWEB)

    Yu, K. [Brookhaven National Lab. (BNL), Upton, NY (United States). Computational Science Initiative; Samulyak, R. [Brookhaven National Lab. (BNL), Upton, NY (United States). Computational Science Initiative; Stony Brook Univ., NY (United States). Dept. of Applied Mathematics and Statistics; Yonehara, K. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Freemire, B. [Northern Illinois Univ., DeKalb, IL (United States)

    2018-01-11

    Muon beam-induced plasma loading of radio-frequency (RF) cavities filled with high pressure hydrogen gas with 1% dry air dopant has been studied via numerical simulations. The electromagnetic code SPACE, that resolves relevant atomic physics processes, including ionization by the muon beam, electron attachment to dopant molecules, and electron-ion and ion-ion recombination, has been used. Simulations studies have also been performed in the range of parameters typical for practical muon cooling channels.

  4. Simulation of plasma loading of high-pressure RF cavities

    Science.gov (United States)

    Yu, K.; Samulyak, R.; Yonehara, K.; Freemire, B.

    2018-01-01

    Muon beam-induced plasma loading of radio-frequency (RF) cavities filled with high pressure hydrogen gas with 1% dry air dopant has been studied via numerical simulations. The electromagnetic code SPACE, that resolves relevant atomic physics processes, including ionization by the muon beam, electron attachment to dopant molecules, and electron-ion and ion-ion recombination, has been used. Simulations studies have been performed in the range of parameters typical for practical muon cooling channels.

  5. Advanced Synchrotron Techniques at High Pressure Collaborative Access Team (HPCAT)

    Science.gov (United States)

    Shen, G.; Sinogeikin, S. V.; Chow, P.; Kono, Y.; Meng, Y.; Park, C.; Popov, D.; Rod, E.; Smith, J.; Xiao, Y.; Mao, H.

    2012-12-01

    High Pressure Collaborative Access Team (HPCAT) is dedicated to advancing cutting-edge, multidisciplinary, high-pressure science and technology using synchrotron radiation at Sector 16 of the Advanced Photon Source (APS) of Argonne National Laboratory. At HPCAT an array of novel x-ray diffraction and spectroscopic techniques has been integrated with high pressure and extreme temperature instrumentation for studies of structure and materials properties at extreme conditions.. HPCAT consists of four active independent beamlines performing a large range of various experiments at extreme conditions. 16BM-B beamline is dedicated to energy dispersive and white Laue X-ray diffraction. The majority of experiments are performed with a Paris-Edinburgh large volume press (to 7GPa and 2500K) and include amorphous and liquid structure measurement, white beam radiography, elastic sound wave velocity measurement of amorphous solid materials, with viscosity and density measurement of liquid being under development. 16BM-D is a monochromatic diffraction beamline for powder and single crystal diffraction at high pressure and high (resistive heating) / low (cryostats) temperature. The additional capabilities include high-resolution powder diffraction and x-ray absorption near edge structure (XANES) spectroscopy. The insertion device beamline of HPCAT has two undulators in canted mode (operating independently) and LN cooled Si monochromators capable of providing a large range of energies. 16IDB is a microdiffraction beamline mainly focusing on high-pressure powder and single crystal diffraction in DAC at high temperatures (double-sided laser heating and resistive heating) and low temperature (various cryostats). The modern instrumentation allows high-quality diffraction at megabar pressures from light element, fast experiments with pulsed laser heating, fast dynamic experiments with Pilatus detector, and so on. 16ID-D beamline is dedicated to x-ray scattering and spectroscopy research

  6. High pressure cell for neutron scattering experiments

    International Nuclear Information System (INIS)

    Shinde, A.B.; Krishna, P.S.R.; Paranjpe, S.K.; Vaidya, S.N.

    1997-01-01

    We report here the design and fabrication of a high pressure clamped cell using EN45 steel for neutron scattering experiments up to 15 kbar. The pressure cell geometry allows detection of scattered neutrons in a plane over an angular range of 90 deg. The cell can be used for both elastic and inelastic scattering measurements on polycrystalline materials and disordered materials. The volume of the sample region is about 400 mm 3 . Preliminary results obtained from neutron diffraction of ND 4 I and KNO 3 are presented. (author)

  7. HIGH PRESSURE COAL COMBUSTON KINETICS PROJECT

    Energy Technology Data Exchange (ETDEWEB)

    Stefano Orsino

    2005-03-30

    As part of the U.S. Department of Energy (DoE) initiative to improve the efficiency of coal-fired power plants and reduce the pollution generated by these facilities, DOE has funded the High-Pressure Coal Combustion Kinetics (HPCCK) Projects. A series of laboratory experiments were conducted on selected pulverized coals at elevated pressures with the specific goals to provide new data for pressurized coal combustion that will help extend to high pressure and validate models for burnout, pollutant formation, and generate samples of solid combustion products for analyses to fill crucial gaps in knowledge of char morphology and fly ash formation. Two series of high-pressure coal combustion experiments were performed using SRI's pressurized radiant coal flow reactor. The first series of tests characterized the near burner flame zone (NBFZ). Three coals were tested, two high volatile bituminous (Pittsburgh No.8 and Illinois No.6), and one sub-bituminous (Powder River Basin), at pressures of 1, 2, and 3 MPa (10, 20, and 30 atm). The second series of experiments, which covered high-pressure burnout (HPBO) conditions, utilized a range of substantially longer combustion residence times to produce char burnout levels from 50% to 100%. The same three coals were tested at 1, 2, and 3 MPa, as well as at 0.2 MPa. Tests were also conducted on Pittsburgh No.8 coal in CO2 entrainment gas at 0.2, 1, and 2 MPa to begin establishing a database of experiments relevant to carbon sequestration techniques. The HPBO test series included use of an impactor-type particle sampler to measure the particle size distribution of fly ash produced under complete burnout conditions. The collected data have been interpreted with the help of CFD and detailed kinetics simulation to extend and validate devolatilization, char combustion and pollutant model at elevated pressure. A global NOX production sub-model has been proposed. The submodel reproduces the performance of the detailed chemical

  8. High-pressure cell for neutron scattering

    International Nuclear Information System (INIS)

    Onodera, Akifumi; Nakai, Yutaka; Kunitomi, Nobuhiko

    1987-01-01

    We have developed a high-pressure cell for neutron scattering. The cell uses a barrel-shaped support cylinder made of sintered ceramics. Samples 6 mm in diameter and 10 mm long can be accommodated. The cell is suitable for use at low and high temperatures, after a pressure generated at room temperature is locked. The change of pressure on cooling to cryogenic temperatures is estimated by measuring the lattice parameter of NaCl. Besides the pressure locking technique, continuous pressurization can be achieved at room temperature by using a built-in mini-press while the cell is mounted on a goniometer of neutron spectrometer. (author)

  9. High pressure hydroformylation in the chemical industry

    Energy Technology Data Exchange (ETDEWEB)

    Paciello, R. [BASF Aktiengesellschaft, Ludwigshafen (Germany)

    2006-07-01

    Higher oxo alcohols are intermediates for large-scale applications, such as plasticizers, detergents and fuel additives, as well as being useful in the synthesis of fine chemicals such as vitamins or flavors and fragrances. Many of these alcohols are still made using high pressure technologies. Advantages and disadvantages of different technologies presently in use or being developed are discussed. In particular, efforts to decrease raw material costs, e.g. by increasing yield, or investment, e.g. by decreasing pressure, will be highlighted. (orig.)

  10. High pressure BF3 proportional counter

    International Nuclear Information System (INIS)

    Mihara, Masaru; Gotoh, Eiichiro; Kodama, Masahiro

    1978-01-01

    Plateau and pulse characteristics of high pressure BF 3 proportional counter were investigated in terms of counter geometry and gas pressure, in order to develop a small-sized and high-sensitive one. Description is given of the construction of improved gas filling equipment with filling procedure. A tentative brass counter, 67 mm in cathode diameter, 40 micron in anode diameter, filled to 1.2 kg/cm 2 revealed characteristics of 150 volts plateau range, the slope of which being 3% per 100 volts at the operation voltage of around 3.3 kV, and 103% full width at half-maximum in the pulse height distribution. (auth.)

  11. Probing Hydrogen Diffusion under High Pressure

    Science.gov (United States)

    Bove, L. E.; Klotz, S.; Strassle, T.; Saitta, M.

    2012-12-01

    volume HP press can be now warmed up to 600K and the peculiar geometry of the gasket assure an excellent signal to background ratio. This new device has been recently settled up on neutron scattering facilities (PSI, ILL), successfully showing that very high quality data can be obtained on liquid water, and more generally on hydrogenated liquids dynamics under high pressure. Some new exciting results on the diffusion mechanism in hot dense water will be presented [9]. Possible future implementation of the device to reach the 20GPa and 1000K conditions will be also discussed. References [1] C. Cavazzoni et al., Science 283, 44 (1999) ; T. Guillot, Science 286 (1999), 72 . 77. [2] Some of the most active groups in this field are the Geophysical Laboratory (USA), Lawrence Livermore National Laboratory (USA), CEA/DAM (France) and the Bayerisches Geoinstitut (Allemagne). [3] Klotz S et al, Phys. Rev. Lett. 96 149602, 2006. [4] Nelmes R J Nature Phys. 2 414, 2006. [5] S. Klotz, L. Bove et al., Nature Mat. 8, 405 (2009). [6] L.E. Bove et al., Phys. Rev. Lett., 106 (2011) . [7] L. E. Bove et al., Phys. Appl. Lett., in preparation (2012). [8] A. Cunsolo et al., Journal of Chem. Phys. 124, 084503 (2006). [9] L.E. Bove et al., Phys. Rev. Lett., submitted (2012) .

  12. High pressure phases of alkali ternary borohydrides

    Science.gov (United States)

    Kumar, Ravhi; Cornelius, Andrew

    2007-03-01

    Insitu synchrotron x-ray diffraction experiments were carried out on MBH4 (M = K and Rb) borohydrides at high pressures up to 26 GPa using diamond anvil cells. KBH4 undergoes a structural transition at 4 GPa to a tetragonal phase from cubic and then to an orthorhombic phase around 7 GPa which are very similar to NaBH4 investigated earlier [1]. However, RbBH4 shows, a direct transition from the ambient cubic to an orthorhombic phase at 2.9 GPa, followed by a monoclinic phase at 8 GPa. Complementary high pressure Raman experiments, support the transitions observed in the diffraction experiments. The results will be presented in detail. [1]. Ravhi S. Kumar and Andrew L. Cornelius, Appl.Phys.Lett., 87,261916 (2005) This work is supported in part by the U.S. Department of Energy (DOE) under Award Number DE-FG36 05GO85028. HPCAT is supported by DOE-BES, DOE-NNSA,NSF, and the W.M. Keck Foundation.

  13. Strain engineered pyrochlore at high pressure

    Energy Technology Data Exchange (ETDEWEB)

    Rittman, Dylan R.; Turner, Katlyn M.; Park, Sulgiye; Fuentes, Antonio F.; Park, Changyong; Ewing, Rodney C.; Mao, Wendy L.

    2017-05-22

    Strain engineering is a promising method for next-generation materials processing techniques. Here, we use mechanical milling and annealing followed by compression in diamond anvil cell to tailor the intrinsic and extrinsic strain in pyrochlore, Dy2Ti2O7 and Dy2Zr2O7. Raman spectroscopy, X-ray pair distribution function analysis, and X-ray diffraction were used to characterize atomic order over short-, medium-, and long-range spatial scales, respectively, under ambient conditions. Raman spectroscopy and X-ray diffraction were further employed to interrogate the material in situ at high pressure. High-pressure behavior is found to depend on the species and concentration of defects in the sample at ambient conditions. Overall, we show that defects can be engineered to lower the phase transformation onset pressure by ~50% in the ordered pyrochlore Dy2Zr2O7, and lower the phase transformation completion pressure by ~20% in the disordered pyrochlore Dy2Zr2O7. These improvements are achieved without significantly sacrificing mechanical integrity, as characterized by bulk modulus.

  14. Plastic reactor suitable for high pressure and supercritical fluid electrochemistry

    OpenAIRE

    Branch, Jack; Alibouri, Mehrdad; Cook, David A.; Richardson, Peter; Bartlett, Philip N.; Matefi-Tempfli, Maria; Matefi-Tempfli, Stefan; Bampton, Mark; Cookson, Tamsin; Connell, Phil; Smith, David

    2017-01-01

    The paper describes a reactor suitable for high pressure, particularly supercritical fluid, electrochemistry and electrodeposition at pressures up to 30 MPa at 115°C. The reactor incorporates two key, new design concepts; a plastic reactor vessel and the use of o-ring sealed brittle electrodes. These two innovations widen what can be achieved with supercritical fluid electrodeposition. The suitability of the reactor for electroanalytical experiments is demonstrated by studies of the voltammet...

  15. Pantothenic Acid (Vitamin B5) in Infant Formula and Adult/ Pediatric Nutritional Formula by Ultra-High Pressure Liquid Chromatography/Tandem Mass Spectrometry Method: Collaborative Study, Final Action 2012.16.

    Science.gov (United States)

    Martin, Frederic; Campos-Giménez, Esther

    2015-01-01

    In order to determine repeatability and reproducibility of AOAC First Action Method 2012.16 [Pantothenic Acid (Vitamin B5) in Infant Formula and Adult/Pediatric Nutritional Formula by Ultra-High Pressure Liquid Chromatography/Tandem Mass Spectrometry], a collaborative study was organized. The study was divided in two parts: method setup and qualification of participants (part 1) and collaborative study participation (part 2). For part 1, each participating laboratory was asked to analyze two practice samples using the aforementioned method. Laboratories that provided results within a range of expected levels were qualified for part 2, during which each laboratory received 10 samples in blind duplicates. Results have been compared to the Standard Method Performance Requirement (SMPR®) 2012.009 established for pantothenic acid. Precision results (repeatability and reproducibility) were within the limits stated in the SMPR. Repeatability ranged from 1.3 to 3.3%, and reproducibility ranged from 4.1 to 7.0%. Horwitz ratio (HorRat) values were all <1, ranging from 0.33 to 0.69. The AOAC Expert Review Panel on Stakeholder Panel on Infant Formula and Adult Nutritionals Nutrient Methods determined that the data presented met the SMPR and recommended the method for Final Action status, which was then granted by the AOAC Official Methods Board.

  16. First report of garnet corundum rocks from southern India: Implications for prograde high-pressure (eclogite-facies?) metamorphism

    Science.gov (United States)

    Shimpo, Makoto; Tsunogae, Toshiaki; Santosh, M.

    2006-02-01

    We report here for the first time the occurrence of garnet and corundum in Mg-Al-rich rocks at Sevitturangampatti (Namakkal district) in the Palghat-Cauvery Shear Zone System (PCSS), southern India. The rocks contain several rare mineral assemblages such as garnet-corundum-sillimanite-cordierite-sapphirine-spinel-Mg-rich staurolite, garnet-corundum-sodic gedrite-cordierite-sillimanite/kyanite, garnet-Mg-rich staurolite-sillimanite/kyanite, sodic gedrite-Mg-rich staurolite-corundum-sapphirine, biotite-corundum-sapphirine and sodic gedrite-sapphirine-spinel-cordierite. Both garnet and corundum in these rocks occur as coarse-grained (1 mm to 10 cm) porphyroblasts in the matrix of sillimanite, cordierite and gedrite. Kyanite is common as inclusions in garnet, but matrix aluminosilicates are mainly sillimanite. The presence of rare garnet + corundum, which has so far been reported from kimberlite xenoliths, aluminous eclogites and ultrahigh-pressure metamorphic rocks as well as in high-pressure experiments, suggests that the assemblage is an indicator of an unusually high-pressure event, which has not been recorded in previous studies from southern India. Phase analysis of quartz-absent MAS system also suggests high-pressure stability of the assemblage. The inference of high pressure metamorphism is also supported by the presence of Mg-rich [Mg/(Fe + Mg) = 0.51] staurolite, which has been reported from high-pressure rocks, included from cores of coarse-grained garnet and gedrite. Porphyroblastic occurrence of garnet + corundum as well as staurolite and kyanite inclusions suggests that the area underwent prograde high-pressure metamorphism, probably in the eclogite field. The rocks subsequently underwent continuous heating at 940 to 990 °C, suggesting ultrahigh-temperature (UHT) metamorphism along a clockwise trajectory. Sapphirine + cordierite and spinel + cordierite symplectites between garnet and sillimanite suggest near isothermal decompression after the peak event

  17. Equation of state of liquid Indium under high pressure

    Directory of Open Access Journals (Sweden)

    Huaming Li

    2015-09-01

    Full Text Available We apply an equation of state of a power law form to liquid Indium to study its thermodynamic properties under high temperature and high pressure. Molar volume of molten indium is calculated along the isothermal line at 710K within good precision as compared with the experimental data in an externally heated diamond anvil cell. Bulk modulus, thermal expansion and internal pressure are obtained for isothermal compression. Other thermodynamic properties are also calculated along the fitted high pressure melting line. While our results suggest that the power law form may be a better choice for the equation of state of liquids, these detailed predictions are yet to be confirmed by further experiment.

  18. The effect of high pressure on nitrogen compounds of milk

    International Nuclear Information System (INIS)

    Kielczewska, Katarzyna; Czerniewicz, Maria; Michalak, Joanna; Brandt, Waldemar

    2004-01-01

    The effect of pressurization at different pressures (from 200 to 1000 MPa, at 200 MPa intervals, t const. = 15 min) and periods of time (from 15 to 35 min, at 10 min intervals, p const. = 800 MPa) on the changes of proteins and nitrogen compounds of skimmed milk was studied. The pressurization caused an increase in the amount of soluble casein and denaturation of whey proteins. The level of nonprotein nitrogen compounds and proteoso-peptone nitrogen compounds increased as a result of the high-pressure treatment. These changes increased with an increase in pressure and exposure time. High-pressure treatment considerably affected the changes in the conformation of milk proteins, which was reflected in the changes in the content of proteins sedimenting and an increase in their degree of hydration

  19. A high temperature high pressure cell for quasielastic neutron scattering.

    Science.gov (United States)

    Yang, F; Kaplonski, J; Unruh, T; Mamontov, E; Meyer, A

    2011-08-01

    We present our recent development of a high temperature high pressure cell for neutron scattering. Combining a water cooled Nb1Zr pressure cell body with an internal heating furnace, the sample environment can reach temperatures of up to 1500 K at a pressure of up to 200 MPa at the sample position, with an available sample volume of about 700 mm(3). The cell material Nb1Zr is specifically chosen due to its reasonable mechanical strength at elevated temperatures and fairly small neutron absorption and incoherent scattering cross sections. With this design, an acceptable signal-to-noise ratio of about 10:1 can be achieved. This opens new possibilities for quasielastic neutron scattering studies on different types of neutron spectrometers under high temperature high pressure conditions, which is particularly interesting for geological research on, e.g., water dynamics in silicate melts.

  20. High-pressure cell for simultaneous dielectric and neutron spectroscopy

    DEFF Research Database (Denmark)

    Sanz, Alejandro; Hansen, Henriette Wase; Jakobsen, Bo

    2018-01-01

    and fast vibrations at the same time. The cell, constructed in cylindrical geometry, is made of a high-strength aluminum alloy and operates up to 500 MPa in a temperature range between roughly 2 and 320 K. In order to measure the scattered neutron intensity and the sample capacitance simultaneously......In this article, we report on the design, manufacture, and testing of a high-pressure cell for simultaneous dielectric and neutron spectroscopy. This cell is a unique tool for studying dynamics on different time scales, from kilo- to picoseconds, covering universal features such as the α relaxation......, a cylindrical capacitor is positioned within the bore of the high-pressure container. The capacitor consists of two concentric electrodes separated by insulating spacers. The performance of this setup has been successfully verified by collecting simultaneous dielectric and neutron spectroscopy data...

  1. High-pressure polymorphism of acetylsalicylic acid (aspirin): Raman spectroscopy

    Science.gov (United States)

    Crowell, Ethan L.; Dreger, Zbigniew A.; Gupta, Yogendra M.

    2015-02-01

    Micro-Raman spectroscopy was used to elucidate the high-pressure polymorphic behavior of acetylsalicylic acid (ASA), an important pharmaceutical compound known as aspirin. Using a diamond anvil cell (DAC), single crystals of the two polymorphic phases of aspirin existing at ambient conditions (ASA-I and ASA-II) were compressed to 10 GPa. We found that ASA-I does not transform to ASA-II, but instead transforms to a new phase (ASA-III) above ∼2 GPa. It is demonstrated that this transformation primarily introduces structural changes in the bonding and arrangement of the acetyl groups and is reversible upon the release of pressure. In contrast, a less dense ASA-II shows no transition in the pressure range studied, though it appears to exhibit a disordered structure above 7 GPa. Our results suggest that ASA-III is the most stable polymorph of aspirin at high pressures.

  2. Tolerance of budding yeast Saccharomyces cerevisiae to ultra high pressure

    Science.gov (United States)

    Shibata, M.; Torigoe, M.; Matsumoto, Y.; Yamamoto, M.; Takizawa, N.; Hada, Y.; Mori, Y.; Takarabe, K.; Ono, F.

    2014-05-01

    Our studies on the tolerance of plants and animals against very high pressure of several GPa have been extended to a smaller sized fungus, the budding yeast Saccharomyces cerevisiae. Several pieces of budding yeast (dry yeast) were sealed in a small teflon capsule with a liquid pressure medium fluorinate, and exposed to 7.5 GPa by using a cubic anvil press. The pressure was kept constant for various duration of time from 2 to 24 h. After the pressure was released, the specimens were brought out from the teflon capsule, and they were cultivated on a potato dextrose agar. It was found that the budding yeast exposed to 7.5 GPa for up to 6 h showed multiplication. However, those exposed to 7.5 GPa for longer than 12 h were found dead. The high pressure tolerance of budding yeast is a little weaker than that of tardigrades.

  3. Long-term follow-up of high-pressure injection injuries to the hand

    NARCIS (Netherlands)

    Wieder, Anat; Lapid, Oren; Plakht, Ygal; Sagi, Amiram

    2006-01-01

    High-pressure injection injury is an injury caused by accidental injection of substances by industrial equipment. This injury may have devastating sequelae. The goal of this study was to assess the long-term outcome of high-pressure injection injury to the hand. In this historical prospective study,

  4. Studies on high-pressure reaction of Er/sub 2/O/sub 3/ or Yb/sub 2/O/sub 3/ with VO/sub 2/

    Energy Technology Data Exchange (ETDEWEB)

    Shin-ike, T. (Osaka Dental Coll., Hirakata (Japan)); Adachi, G.; Shiokawa, J.; Shimada, M.; Koizumi, M.

    1980-12-01

    The reaction of erbium sesquioxide (Er/sub 2/O/sub 3/) or ytterbium sesquioxide (Yb/sub 2/O/sub 3/) with vanadium dioxide (VO/sub 2/) at 1400/sup 0/C and 50 kbar and 30 kbar pressures was studied. Quadrivalent vanadium ions were reduced to the trivalent state, erbium vanadate (ErVO/sub 3/) or ytterbium vanadate (YbVO/sub 3/) being obtained. The crystal structure of ErVO/sub 3/ obtained at 50 kbar pressure was vaterite-type isostructural with ErBO/sub 3/ belonging to a hexagonal system, and that obtained at 30 kbar calcite-type belonging to a rhombohedral (pseudo-hexagonal) system. In the reaction of Yb/sub 2/O/sub 3/ with VO/sub 2/ at high pressure, a perovskite-type crystal was obtained. The electrical and magnetic properties of the vaterite- and the calcite-type ErVO/sub 3/ were studied.

  5. Developing Reading Comprehension through Metacognitive Strategies: A Review of Previous Studies

    Science.gov (United States)

    Channa, Mansoor Ahmed; Nordin, Zaimuariffudin Shukri; Siming, Insaf Ali; Chandio, Ali Asgher; Koondher, Mansoor Ali

    2015-01-01

    This paper has reviewed the previous studies on metacognitive strategies based on planning, monitoring, and evaluating in order to develop reading comprehension. The main purpose of this review in metacognition, and reading domain is to help readers to enhance their capabilities and power reading through these strategies. The researchers reviewed…

  6. Study of some physical aspects previous to design of an exponential experiment

    International Nuclear Information System (INIS)

    Caro, R.; Francisco, J. L. de

    1961-01-01

    This report presents the theoretical study of some physical aspects previous to the design of an exponential facility. The are: Fast and slow flux distribution in the multiplicative medium and in the thermal column, slowing down in the thermal column, geometrical distribution and minimum needed intensity of sources access channels and perturbations produced by possible variations in its position and intensity. (Author) 4 refs

  7. Effect of High Pressure and Heat on Bacterial Toxins

    Directory of Open Access Journals (Sweden)

    Dirk Margosch

    2005-01-01

    Full Text Available Even though the inactivation of microorganisms by high pressure treatment is a subject of intense investigations, the effect of high pressure on bacterial toxins has not been studied so far. In this study, the influence of combined pressure/temperature treatment (0.1 to 800 MPa and 5 to 121 °C on bacterial enterotoxins was determined. Therefore, heat-stable enterotoxin (STa of cholera toxin (CT from Vibrio cholerae, staphylococcal enterotoxins A-E, haemolysin BL (HBL from Bacillus cereus, and Escherichia coli (STa were subjected to different treatment schemes. Structural alterations were monitored in enzyme immunoassays (EIAs. Cytotoxicity of the pressure treated supernatant of toxigenic B. cereus DSM 4384 was investigated with Vero cells. High pressure of 200 to 800 MPa at 5 °C leads to a slight increase of the reactivity of the STa of E. coli. However, reactivity decreased at 800 MPa and 80 °C to (66±21 % after 30 min and to (44±0.3 % after 128 min. At ambient pressure no decrease in EIA reactivity could be observed after 128 min. Pressurization (0.1 to 800 MPa of heat stable monomeric staphylococcal toxins at 5 and 20 °C showed no effect. A combined heat (80 °C and pressure (0.1 to 800 MPa treatment lead to a decrease in the immuno-reactivity to 20 % of its maximum. For cholera toxin a significant loss in latex agglutination was observable only at 80 °C and 800 MPa for holding times higher than 20 min. Interestingly, the immuno-reactivity of B. cereus HBL toxin increased with the increase of pressure (182 % at 800 MPa, 30 °C, and high pressure showed only minor effects on cytotoxicity to Vero cells. Our results indicate that pressurization can increase inactivation observed by heat treatment, and combined treatments may be effective at lower temperatures and/or shorter incubation time.

  8. Vibron Dynamics of Hydrogen at High Pressures and Temperatures

    Science.gov (United States)

    Johnson, Karl; Feldman, Joseph; Hemley, Russell

    2006-03-01

    There is currently great interest in the behavior of molecular hydrogen at high pressures and temperatures. The van Kranendonk theory of vibrons in solid hydrogen has been used previously to provide a description of the Raman response as a function of pressure and para-ortho concentrations at low temperature. Here we apply the same model to very different environments, namely to the solid at high P-T conditions, and, with less justification, to the dense fluid. The effect of temperature is presumed to be to renormalize the hopping parameter. Within our model of the vibrons and approximate harmonic lattice dynamics, a 1/R^6 dependence of the hopping parameter on intermolecular distance, R, gets averaged over fluctuations in the interatomic distance, and the average increases with temperature. Preliminary results using configurations obtained from hybrid path integral molecular dynamics calculations with empirical potentials suggest that there is very little change in the Raman peak upon melting at high pressure, in agreement with previous high P-T measurements.

  9. High-pressure structures of methane hydrate

    CERN Document Server

    Hirai, H; Fujihisa, H; Sakashita, M; Katoh, E; Aoki, K; Yamamoto, Y; Nagashima, K; Yagi, T

    2002-01-01

    Three high-pressure structures of methane hydrate, a hexagonal structure (str. A) and two orthorhombic structures (str. B and str. C), were found by in situ x-ray diffractometry and Raman spectroscopy. The well-known structure I (str. I) decomposed into str. A and fluid at 0.8 GPa. Str. A transformed into str. B at 1.6 GPa, and str. B further transformed into str. C at 2.1 GPa which survived above 7.8 GPa. The fluid solidified as ice VI at 1.4 GPa, and the ice VI transformed to ice VII at 2.1 GPa. The bulk moduli, K sub 0 , for str. I, str. A, and str. C were calculated to be 7.4, 9.8, and 25.0 GPa, respectively.

  10. Superconductivity from magnetic elements under high pressure

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, Katsuya [KYOKUGEN, Research Center for Materials Science at Extreme Conditions, Osaka University, Osaka 560-8531 (Japan)]. E-mail: shimizu@rcem.osaka-u.ac.jp; Amaya, Kiichi [Toyota Physical and Chemical Research Institute, Aichi 480-1192 (Japan); Suzuki, Naoshi [Graduate School of Engineering Science, Osaka University, Osaka 560-8531 (Japan); Onuki, Yoshichika [Graduate School of Science, Osaka University, Osaka 560-0043 (Japan)

    2006-05-01

    Can we expect the appearance of superconductivity from magnetic elements? In general, superconductivity occurs in nonmagnetic metal at low temperature and magnetic impurities destroy superconductivity; magnetism and superconductivity are as incompatible as oil and water. Here, we present our experimental example of superconducting elements, iron and oxygen. They are magnetic at ambient pressure, however, they become nonmagnetic under high pressure, then superconductor at low temperature. What is the driving force of the superconductivity? Our understanding in the early stages was a simple scenario that the superconductive state was obtained as a consequence of an emergence of the nonmagnetic states. In both cases, we may consider another scenario for the appearance of superconductivity; the magnetic fluctuation mechanism in the same way as unconventional superconductors.

  11. Superconductivity from magnetic elements under high pressure

    International Nuclear Information System (INIS)

    Shimizu, Katsuya; Amaya, Kiichi; Suzuki, Naoshi; Onuki, Yoshichika

    2006-01-01

    Can we expect the appearance of superconductivity from magnetic elements? In general, superconductivity occurs in nonmagnetic metal at low temperature and magnetic impurities destroy superconductivity; magnetism and superconductivity are as incompatible as oil and water. Here, we present our experimental example of superconducting elements, iron and oxygen. They are magnetic at ambient pressure, however, they become nonmagnetic under high pressure, then superconductor at low temperature. What is the driving force of the superconductivity? Our understanding in the early stages was a simple scenario that the superconductive state was obtained as a consequence of an emergence of the nonmagnetic states. In both cases, we may consider another scenario for the appearance of superconductivity; the magnetic fluctuation mechanism in the same way as unconventional superconductors

  12. High pressure and high temperature apparatus

    Science.gov (United States)

    Voronov, Oleg A.

    2005-09-13

    A design for high pressure/high temperature apparatus and reaction cell to achieve .about.30 GPa pressure in .about.1 cm volume and .about.100 GPa pressure in .about.1 mm volumes and 20-5000.degree. C. temperatures in a static regime. The device includes profiled anvils (28) action on a reaction cell (14, 16) containing the material (26) to be processed. The reaction cell includes a heater (18) surrounded by insulating layers and screens. Surrounding the anvils are cylindrical inserts and supporting rings (30-48) whose hardness increases towards the reaction cell. These volumes may be increased considerably if applications require it, making use of presses that have larger loading force capability, larger frames and using larger anvils.

  13. High Pressure Quick Disconnect Particle Impact Tests

    Science.gov (United States)

    Rosales, Keisa R.; Stoltzfus, Joel M.

    2009-01-01

    NASA Johnson Space Center White Sands Test Facility (WSTF) performed particle impact testing to determine whether there is a particle impact ignition hazard in the quick disconnects (QDs) in the Environmental Control and Life Support System (ECLSS) on the International Space Station (ISS). Testing included standard supersonic and subsonic particle impact tests on 15-5 PH stainless steel, as well as tests performed on a QD simulator. This paper summarizes the particle impact tests completed at WSTF. Although there was an ignition in Test Series 4, it was determined the ignition was caused by the presence of a machining imperfection. The sum of all the test results indicates that there is no particle impact ignition hazard in the ISS ECLSS QDs. KEYWORDS: quick disconnect, high pressure, particle impact testing, stainless steel

  14. Synthesis and stability of hydrogen selenide compounds at high pressure

    Energy Technology Data Exchange (ETDEWEB)

    Pace, Edward J.; Binns, Jack; Alvarez, Miriam Pena; Dalladay-Simpson, Philip; Gregoryanz, Eugene; Howie, Ross T. (Edinburgh); (CHPSTAR- China)

    2017-11-14

    The observation of high-temperature superconductivity in hydride sulfide (H2S) at high pressures has generated considerable interest in compressed hydrogen-rich compounds. High-pressure hydrogen selenide (H2Se) has also been predicted to be superconducting at high temperatures; however, its behaviour and stability upon compression remains unknown. In this study, we synthesize H2Se in situ from elemental Se and molecular H2 at pressures of 0.4 GPa and temperatures of 473 K. On compression at 300 K, we observe the high-pressure solid phase sequence (I-I'-IV) of H2Se through Raman spectroscopy and x-ray diffraction measurements, before dissociation into its constituent elements. Through the compression of H2Se in H2 media, we also observe the formation of a host-guest structure, (H2Se)2H2, which is stable at the same conditions as H2Se, with respect to decomposition. These measurements show that the behaviour of H2Se is remarkably similar to that of H2S and provides further understanding of the hydrogen chalcogenides under pressure.

  15. The system BaOGeO 2 at high pressures and temperatures, with special reference to high-pressure transformations in BaGeO 3, BaGe 2O 5, and Ba 2Ge 5O 12

    Science.gov (United States)

    Ozima, Mituko; Susaki, Jun-Ichi; Akimoto, Syun-Iti; Shimizu, Yoshio

    1982-10-01

    Phase relations in the system BaOGeO 2 were investigated in the pressure range 20-70 kbar in the temperature range 750-1200°C. Several new phases were identified in this system: an atmospheric phase of BaGe 2O 5 (monoclinic BaGe 2O 5 I), two high-pressure phases of BaGe 2O 5 (monoclinic BaGe 2O 5 II and tetragonal BaGe 2O 5 III), and a high-pressure phase of Ba 2Ge 5O 12. The phase boundary curve between BaGe 2O 5 II and BaGe 2O 5 III was preliminarily determined as P(kbar) = 7.7 + 0.047 T (°C). The high-pressure phases of BaGeO 3, which were previously reported by Y. Shimizu, Y. Syono, and S. Akimoto ( High Temp.-High Pressures2, 113 (1970)) in the pressure range 15-95 kbar, were interpreted to be not single-phase materials but complicated mixtures of more than two phases in the system BaOGeO 2. X-Ray powder diffraction data for the new compounds synthesized in this study are given.

  16. Study of functional-performance deficits in athletes with previous ankle sprains

    Directory of Open Access Journals (Sweden)

    hamid Babaee

    2008-04-01

    Full Text Available Abstract Background: Despite the importance of functional-performance deficits in athletes with history of ankle sprain few, studies have been carried out in this area. The aim of this research was to study relationship between previous ankle sprains and functional-performance deficits in athletes. Materials and methods: The subjects were 40 professional athletes selected through random sampling among volunteer participants in soccer, basketball, volleyball and handball teams of Lorestan province. The subjects were divided into 2 groups: Injured group (athletes with previous ankle sprains and healthy group (athletes without previous ankle sprains. In this descriptive study we used Functional-performance tests (figure 8 hop test and side hop test to determine ankle deficits and limitations. They participated in figure 8 hop test including hopping in 8 shape course with the length of 5 meters and side hop test including 10 side hop repetitions in course with the length of 30 centimeters. Time were recorded via stopwatch. Results: After data gathering and assessing information distributions, Pearson correlation was used to assess relationships, and independent T test to assess differences between variables. Finally the results showed that there is a significant relationship between previous ankle sprains and functional-performance deficits in the athletes. Conclusion: The athletes who had previous ankle sprains indicated functional-performance deficits more than healthy athletes in completion of mentioned functional-performance tests. The functional-performance tests (figure 8 hop test and side hop test are sensitive and suitable to assess and detect functional-performance deficits in athletes. Therefore we can use the figure 8 hop and side hop tests for goals such as prevention, assessment and rehabilitation of ankle sprains without spending too much money and time.

  17. Previous treatment influences fingolimod efficacy in relapsing-remitting multiple sclerosis: results from an observational study.

    Science.gov (United States)

    Baldi, Eleonora; Guareschi, Angelica; Vitetta, Francesca; Senesi, Caterina; Curti, Erica; Montepietra, Sara; Simone, Anna Maria; Immovilli, Paolo; Caniatti, Luisa; Tola, Maria Rosaria; Pesci, Ilaria; Montanari, Enrico; Sola, Patrizia; Granella, Franco; Motti, Luisa; Ferraro, Diana

    2014-09-01

    Fingolimod (FTY) is licensed as a disease-modifying treatment in highly active relapsing-remitting multiple sclerosis. The aim of the study was to evaluate the efficacy and safety of FTY in a real-life setting and to explore the possible role of clinical and MRI parameters, including previous treatment type, in predicting its efficacy. Clinical and MRI data was collected on 127 patients assigned to treatment with FTY in six multiple sclerosis centers in Emilia-Romagna, Italy, between August 2011 and June 2013. During a mean follow-up period of 10 months (range 1-22), we observed a total of 47 relapses in 39 patients (30.7%); new T2 lesions or gadolinium-enhancing (Gd+) lesions were present at follow-up MRI in 32/71 patients (45%). Expanded disability status scale (EDSS) at the end of the follow-up period was not different when compared to the baseline EDSS. Serious adverse events occurred in three patients (2.4%). A higher proportion of patients previously treated with natalizumab showed clinical (41%) or MRI activity (54%). Previous treatment with natalizumab increased the risk of a relapse within 30 days (versus immunomodulatory drugs; OR: 4.3; p = 0.011) and at survival analysis (versus remaining patients; HR: 1.9; p = 0.046). Study limitations include a small population sample, a short observation period with variable timing of follow-up MRI and different baseline characteristics of patients previously treated with natalizumab compared to those treated with immunomodulatory drugs. This study confirms the efficacy of FTY in reducing relapse rate in patients previously treated with immunomodulatory drugs, while it seems to be less effective in patients discontinuing natalizumab. Due to the short duration of follow-up it is not possible to evaluate disability progression; however, no difference was observed between the groups.

  18. Previous infection and the risk of ischaemic stroke in Italy: the IN2 study.

    Science.gov (United States)

    Consoli, D; Vidale, S; Aguglia, U; Bassi, P; Cavallini, A; Galati, F; Guidetti, D; Marcello, N; Micieli, G; Pracucci, G; Rasura, M; Siniscalchi, A; Sterzi, R; Toni, D; Inzitari, D

    2015-03-01

    There is an increasing interest in new risk factors for ischaemic stroke. Acute and chronic infections could contribute to different aetiological mechanisms of atherosclerosis that lead to cerebrovascular disease. The aim of this study was to investigate the hypothesis that previous infections and Chlamydia pneumoniae in particular increase the risk of ischaemic stroke in the population. This was a prospective case-control study involving 11 Italian stroke units. Controls were age- and sex-matched with cases, represented by patients admitted to hospital for acute ischaemic stroke. For each participant classical vascular risk factors and previous inflammatory and infectious events up to 1 month before were registered. Blood samples were collected to analyse inflammatory markers and titres of antibodies against C. pneumoniae. A total of 1002 participants were included (mean age 69 years) with 749 ischaemic stroke patients. Infections occurred within 1 month previously in 12% of the entire sample with a higher prevalence in the case group (14.4% vs. 3.9%). At multivariate analysis of the seropositivity of IgA antibodies against C. pneumoniae increased the risk of stroke significantly (relative risk 2.121; 95% confidence interval 1.255-3.584) and an early previous infection (up to 7 days before the event) contributed to a rise in probability of acute cerebral ischaemia (relative risk 3.692; 95% confidence interval 1.134-6.875). Early previous infections and persistent chronic infection of C. pneumoniae could contribute to increase the risk of ischaemic stroke significantly, in the elderly especially. © 2014 EAN.

  19. High pressure structural phase transitions of TiO2 nanomaterials

    International Nuclear Information System (INIS)

    Li Quan-Jun; Liu Bing-Bing

    2016-01-01

    Recently, the high pressure study on the TiO 2 nanomaterials has attracted considerable attention due to the typical crystal structure and the fascinating properties of TiO 2 with nanoscale sizes. In this paper, we briefly review the recent progress in the high pressure phase transitions of TiO 2 nanomaterials. We discuss the size effects and morphology effects on the high pressure phase transitions of TiO 2 nanomaterials with different particle sizes, morphologies, and microstructures. Several typical pressure-induced structural phase transitions in TiO 2 nanomaterials are presented, including size-dependent phase transition selectivity in nanoparticles, morphology-tuned phase transition in nanowires, nanosheets, and nanoporous materials, and pressure-induced amorphization (PIA) and polyamorphism in ultrafine nanoparticles and TiO 2 -B nanoribbons. Various TiO 2 nanostructural materials with high pressure structures are prepared successfully by high pressure treatment of the corresponding crystal nanomaterials, such as amorphous TiO 2 nanoribbons, α -PbO 2 -type TiO 2 nanowires, nanosheets, and nanoporous materials. These studies suggest that the high pressure phase transitions of TiO 2 nanomaterials depend on the nanosize, morphology, interface energy, and microstructure. The diversity of high pressure behaviors of TiO 2 nanomaterials provides a new insight into the properties of nanomaterials, and paves a way for preparing new nanomaterials with novel high pressure structures and properties for various applications. (topical review)

  20. On the origin of the giant isotopic effect of hydrogen on the magnetic properties of YFe.sub.2./sub.A.sub.4.2./sub. (A = H, D): a high pressure study

    Czech Academy of Sciences Publication Activity Database

    Isnard, O.; Paul-Boncour, V.; Arnold, Zdeněk

    2013-01-01

    Roč. 102, č. 12 (2013), "122408-1"-"122408-4" ISSN 0003-6951 R&D Projects: GA ČR GAP204/12/0692 Institutional support: RVO:68378271 Keywords : antiferromagnetic materials * compressibility * ferromagnetic materials * ferromagnetic-antiferromagnetic transitions * high-pressure effects * iron compoounds Subject RIV: BE - Theoretical Physics Impact factor: 3.515, year: 2013

  1. Study of magnetic, structural and magnetocaloric properties of La.sub.0.6./sub.Pr.sub.0.4./sub.Mn.sub.2./sub.Si.sub.2./sub. under high pressures and magnetic field

    Czech Academy of Sciences Publication Activity Database

    Kaštil, Jiří; Arnold, Zdeněk; Isnard, O.; Skourski, Y.; Kamarád, Jiří; Itié, J.P.

    2017-01-01

    Roč. 424, Feb (2017), s. 416-420 ISSN 0304-8853 R&D Projects: GA ČR GA15-03777S Institutional support: RVO:68378271 Keywords : magnetization * compressibility * magnetocaloric effect * high pressure Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 2.630, year: 2016

  2. High-pressure structural stability of the ductile intermetallic ...

    Indian Academy of Sciences (India)

    Keywords. Intermetallics; X-ray diffraction; high pressure; synchrotron radiation. Abstract. High-pressure angle dispersive ... Author Affiliations. S Meenakshi1. High Pressure and Synchrotron Radiation Physics Division, Bhabha Atomic Research Centre, Mumbai 400 085, India. Dates. Manuscript received: 10 July 2013 ...

  3. 30 CFR 57.13021 - High-pressure hose connections.

    Science.gov (United States)

    2010-07-01

    ... Air and Boilers § 57.13021 High-pressure hose connections. Except where automatic shutoff valves are... 30 Mineral Resources 1 2010-07-01 2010-07-01 false High-pressure hose connections. 57.13021...-pressure hose lines of 3/4-inch inside diameter or larger, and between high-pressure hose lines of 3/4-inch...

  4. 30 CFR 56.13021 - High-pressure hose connections.

    Science.gov (United States)

    2010-07-01

    ... and Boilers § 56.13021 High-pressure hose connections. Except where automatic shutoff valves are used, safety chains or other suitable locking devices shall be used at connections to machines of high-pressure... 30 Mineral Resources 1 2010-07-01 2010-07-01 false High-pressure hose connections. 56.13021...

  5. Application of ultra-high-pressure liquid chromatography-tandem mass spectrometry to the determination of multi-class pesticides in environmental and wastewater samples. Study of matrix effects.

    Science.gov (United States)

    Marín, José M; Gracia-Lor, Emma; Sancho, Juan V; López, Francisco J; Hernández, Félix

    2009-02-27

    An ultra-high-pressure liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS) method for the determination of 37 pesticides (herbicides, insecticides and fungicides) in environmental and wastewater has been developed. To efficiently combine UHPLC with MS/MS, a fast-acquisition triple quadrupole mass analyzer was used. This analyzer (minimum dwell time, 5 ms) allows acquiring up to three simultaneous transitions in the selected reaction monitoring mode for each compound assuring a reliable identification without resolution or sensitivity losses. A pre-concentration step based on solid-phase extraction using Waters Oasis HLB cartridges (0.2 g) was applied with a 100-fold pre-concentration factor along the whole analytical procedure. The method was validated based on European SANCO guidelines using surface, ground, drinking and treated water (from an urban solid residues treatment plant) spiked at two concentration levels (0.025 and 0.1 microg/L), the lowest having been established as the limit of quantification objective. The method showed excellent sensitivity, with instrumental limits of detection ranging from 0.1 to 7 pg. It was applied to environmental water samples (ground and surface water) as well as to samples of urban solid waste leachates (raw leachate and treated leachate after applying reversed osmosis) collected from a municipal treatment plant. Matrix effects have been studied in the different types of water samples analyzed, and several isotope-labelled internal standards have been evaluated as a way to compensate the signal suppression observed for most of the compounds studied, especially in wastewater samples. As a general remark, only those pesticides which response was corrected using their own isotope-labelled molecule, could be satisfactorily corrected in all type of samples, assuring in this way the accurate quantification in all matrix samples.

  6. Temperature control in large-internal-diameter scaffolded monolithic columns operated at ultra-high pressures.

    Science.gov (United States)

    Vonk, Rudy J; Aalbers, Tom; Eeltink, Sebastiaan; Schoenmakers, Peter J

    2015-07-03

    Scaffolding makes it feasible to create organic-polymer monoliths in large confinements, such as wide-bore columns. By creating the scaffold from a metal good heat conductivity inside the column is obtained, which renders the relatively large columns (comparable with 4.6 mm i.d.) suitable for application under ultra-high-pressure LC conditions. It was anticipated that the metal scaffold would allow accurate control of the temperature within the columns, but the temperature profiles within the columns could not be characterized using the previously available small-internal-diameter scaffolded columns. In the current study the internal diameter of the scaffolded columns was increased up to square conduits of 4×4 mm. Prior to the formation of the stationary phase the heating efficiency in the empty scaffolded conduits was addressed. The performance of stationary phases created in the large scaffolds was investigated using the kinetic performance approach and the results were compared to those of the previous studies. Finally, scaffolded columns were tested under ultra-high-pressure LC conditions, where good temperature control is essential. Copyright © 2015 Elsevier B.V. All rights reserved.

  7. Comparative study on the high pressure inactivation behavior of the Shiga toxin-producing Escherichia coli O104:H4 and O157:H7 outbreak strains and a non-pathogenic surrogate.

    Science.gov (United States)

    Reineke, Kai; Sevenich, Robert; Hertwig, Christian; Janßen, Traute; Fröhling, Antje; Knorr, Dietrich; Wieler, Lothar H; Schlüter, Oliver

    2015-04-01

    Enterohemorrhagic Escherichia coli strains cause each year thousands of illnesses, which are sometimes accompanied by the hemolytic uremic syndrome, like in the 2011 outbreak in Germany. For preservation thermal pasteurization is commonly used, which can cause unwanted quality changes. To prevent this high pressure treatment is a potential alternative. Within this study, the 2011 outbreak strain O104:H4, an O157:H7 and a non-pathogenic strain (DSM1116) were tested. The cells were treated in buffer (pH 7 and pH 5) and carrot juice (pH 5.1) in a pressure temperature range of 0.1-500 MPa and 20-70 °C. Flow cytometry was used to investigate the pressure impact on cell structures of the strain DSM1116. Both pathogenic strains had a much higher resistance in buffer and carrot juice than the non-pathogenic surrogate. Further, strains cultivated and treated at a lower pH-value showed higher pressure stability, presumably due to variations in the membrane composition. This was confirmed for the strain DSM1116 by flow cytometry. Cells cultivated and treated at pH 5 had a stronger ability to retain their membrane potential but showed higher rates of membrane permeabilization at pressures <200 MPa compared to cells cultivated and treated at pH 7. These cells had the lowest membrane permeabilization rate at around 125 MPa, possibly denoting that variations in the fatty acid composition and membrane fluidity contribute to this stabilization phenomenon. Copyright © 2014 Elsevier Ltd. All rights reserved.

  8. The high-pressure behavior of bloedite

    DEFF Research Database (Denmark)

    Comodi, Paola; Nazzareni, Sabrina; Balic Zunic, Tonci

    2014-01-01

    High-pressure single-crystal synchrotron X‑ray diffraction was carried out on a single crystal of bloedite [Na2Mg(SO4)24H2O] compressed in a diamond-anvil cell. The volume-pressure data, collected up to 11.2 GPa, were fitted by a second- and a third-order Birch-Murnaghan equation of state (EOS......), yielding V0 = 495.6(7) Å3 with K0 = 39.9(6) GPa, and V0 = 496.9(7) Å3, with K0 = 36(1) GPa and K′ = 5.1 (4) GPa-1, respectively. The axial moduli were calculated using a Birch-Murnaghan EOS truncated at the second order, fixing K′ equal to 4, for a and b axes and a third-order Birch-Murnaghan EOS for c...... axis. The results were a0 = 11.08(1) and K0 = 56(3) GPa, b0 = 8.20(2) and K0 = 43(3) GPa, and c0 = 5.528(5), K0 = 40(2) GPa, K′ = 1.7(3) GPa-1. The values of the compressibility for a, b, and c axes are ba = 0.0060(3) GPa-1, bb = 0.0078(5) GPa-1, bc = 0.0083(4) GPa-1 with an anisotropic ratio of ba...

  9. High-pressure structures of yttrium hydrides

    Science.gov (United States)

    Liu, Lu-Lu; Sun, Hui-Juan; Wang, C. Z.; Lu, Wen-Cai

    2017-08-01

    In this work, the crystal structures of YH3 and YH4 at high pressure (100-250 GPa) have been explored using a genetic algorithm combined with first-principles calculations. New structures of YH3 with space group symmetries of P21/m and I4/mmm were predicted. The electronic structures and the phonon dispersion properties of various YH3 and YH4 structures at different temperatures and pressures were investigated. Among YH3 phases, the P21/m structure of YH3 was found to have a relatively high superconducting transformation temperature T c of 19 K at 120 GPa, which is reduced to 9 K at 200 GPa. Other YH3 structures have much lower T cs. Compared with YH3, the T c of the YH4 compound is much higher, i.e. 94 K at 120 GPa and 55 K at 200 GPa.

  10. Photophysics of organic molecules at high pressure

    Energy Technology Data Exchange (ETDEWEB)

    Mitchell, Dean James [Univ. of Illinois, Urbana-Champaign, IL (United States)

    1978-01-01

    The pressure dependence of emission intensities, energies, and lifetimes of several classes of organic compounds in plastic media were investigated over the range 0-140 kilobars. The fluorescence intensity of 9-anthraldehyde, 9-acetylanthracene, and 9-benzoylanthracene increases remarkably with increasing pressure, accompanied by a large red shift in the emission spectrum. For azulene and several derivatives, the efficiency of fluorescence from both the second and first excited singlet states was pressure dependent as was the relative energy of these states. The rate of internal conversion depended strongly on the energy separating the relevant states. The energy and quantum efficiency of fluorescence for fluorenone in crystalline form and in several polymeric matrices was measured as a function of pressure. The quantum yield, ranged from 0.001 at low pressure to a maximum of about 0.1 at high pressure in paraffinic plastics. Fluorescence quantum yields and phosphorescence quantum yields and lifetimes were measured for pyrazine (P) 2,6-dimethylpyrazine and tetramethylpyrazine (TMP) in PMMA over the pessure range 20-120 kbar. An additional emission, which is attributed to excimer fluorescence, was also observed for these samples and for crystalline pyrazine. The phosphorescence radiative lifetime for P and TMP was about 18 ms.

  11. High pressure waterjet cutting industrial needs survey

    Science.gov (United States)

    Klavuhn, John; Baker, Bruce

    1989-08-01

    The results are presented of a survey conducted by personnel of the National Center for Excellence in Metalworking Technology (NCEMT) to assess the industrial needs in high pressure water jet cutting (WJC) technology. Survey forms were mailed to approximately 1400 individuals obtained from three mailing lists. The respondents included approximately 200 individuals associated with a variety of industries: 12 percent were WJC equipment suppliers, 40 percent were WJC users, and 48 percent were neither suppliers nor users. The survey addressed five specific areas of WJC technology: research and development, standards, systems, new products, and training and service. Results show that the need having the highest priority is the establishment of a database on WJC that contains the cutting parameters for a wide range of materials. Associated with this objective is the expressed need for an independent demonstration and test center for testing, data generation and operator training. A further need was found for establishing organized efforts in hardware development and research in mechanisms of cutting.

  12. HIV-related neuropsychological impairment in patients with previous substance use: A preliminary study

    OpenAIRE

    García-Torres, Amalia; Vergara-Moragues, Esperanza (UNIR); Piñón-Blanco, Adolfo; Pérez-García, Miguel

    2015-01-01

    Human immunodeficiency virus (HIV) can result in cognitive disorders that significantly interfere with the daily activities of HIV patients. These disorders may be worse when there is a history of psychoactive substance use. Our objective is to assess the neuropsychological profile in a group of HIV patients with previous drug use compared to a group of HIV-negative patients with a history of drug use. The study included a total of 28 Spanish adult subjects, of which 14 were HIV-infected and ...

  13. Data from studies of previous radioactive waste disposal in Massachusetts Bay

    International Nuclear Information System (INIS)

    Curtis, W.R.; Mardis, H.M.

    1984-12-01

    This report presents the results of studies conducted in Massachusetts Bay during 1981 and 1982. Included are data from: (1) a side scan sonar survey of disposal areas in the Bay that was carried out by the National Oceanic and Atmospheric Administration (NOAA) for EPA; (2) Collections of sediment and biota by NOAA for radiochemical analysis by EPA; (3) collections of marketplace seafood samples by the Food and Drug Administration (FDA) for radioanalysis by both FDA and EPA; and (4) a radiological monitoring survey of LLW disposal areas by EPA to determine whether there should be any concern for public health resulting from previous LLW disposals in the Bay

  14. Cystic echinococcosis in Jordan: A review of causative species, previous studies, serological and radiological diagnosis.

    Science.gov (United States)

    Hijjawi, Nawal S; Al-Radaideh, Ali M; Rababah, Eman M; Al-Qaoud, Khaled M; Bani-Hani, Kamal E

    2018-03-01

    Cystic echinococcosis (CE)/hydatidosis is a zoonotic disease which occur in human and herbivore animals as a result of infection with the larval stage of the taeniid cestode Echinococcus granulosus sensu lato (s. l.). In human, CE is a serious public health concern in many parts of the world including Jordan. The present review will cover CE causative agent: E. granulosus species/genotypes; life cycle of E. granulosus parasite, all published previous studies on CE in Jordan (humans, intermediate hosts, definitive host) as well as its diagnostic methods in human. Copyright © 2017 Elsevier B.V. All rights reserved.

  15. Microbial Adaptation to High Pressures - From Denial to a New Paradigm Shift

    Science.gov (United States)

    Sharma, A.

    2011-12-01

    The question of microbial survival at high pressure and temperature is considered important to the origin, search and adaptation of life on Earth and other planetary bodies. Field studies have shown the realm of life far exceeding the limits of direct sample accessibility, but these studies have been at the edge of sampling accessibility. Not surprisingly most studies on high pressure have focused on the presumption that pressure as a variable is limiting to biology. The only previous study (Sharma et al. 2002) that experimentally demonstrated cellular activity at high (Gigapascal) pressures using in-situ observations was considered as an outlier or an anomaly and largely ignored in published literature. A number of subsequent studies (e.g. Daniel et al. 2006, Meersman and Heremans 2008) continued asserting indirect and IR study single isolated protein measurements as indication of limits about 300MPa for any viable life. On the other hand, more simplistically, geologists have relied on the conventional closure of open fractures to about few kilometers depth as a scenario limiting any microbial ecosystem. These biochemical and apparent geological limitations have not only sidelined significant observations of rapid adaptation and survival of microbial life at high pressures (Sharma et al 2002), Vanlint et al. 2011), but have made such critical observations as mere anecdotal footnotes to deep life research; despite the fact that these experimental results have opened up a wide range of possibilities for biophysics and biology overcoming obsolete assumptions. Here the author revisits the high pressure survival of microbes by expanding the range of pressures synergistically with temperature and time exposure on Escherichia coli . The results demonstrate continued cell viability at greatly elevated temperature (upto 160 C) and pressure (upto 2400 MPa). The experimental data suggest the cell viability curve mimics a Clapeyeron-type (entropy-volume) thermodynamic

  16. Exotic magnetic structures in high-pressure synthesized perovskites

    Science.gov (United States)

    Manuel, Pascal; Khalyavin, Dmitry; Ding, Lei; Yi, Wei; Kumagai, Yu; Oba, Fumiyasu; Orlandi, Fabio; Belik, Alexei

    We present a neutron powder diffraction study of the crystal and magnetic structures of the high-pressure stabilized perovskite phases of TlMnO3, ScCrO3, InCrO3 and TlCrO3. These compounds exhibit original magnetic structures compared to other members of their respective manganite and orthochromite families with TlMnO3 also displaying unusual orbital ordering pattern. For both systems, we rationalise the structures through a combination of group theory and first principle calculations. We also highlight the dominant mechanism controlling the spin direction as being the single ion anisotropy.

  17. The high pressure xenon lamp as a source of radiation

    International Nuclear Information System (INIS)

    Heerdt, J.A. ter.

    1979-01-01

    An account is given of an investigation into the radiation properties of a commercially available high pressure xenon lamp (type XBO 900 W) in the spectral range 0.3 to 3 μm. The purpose of the study was to find out whether such a lamp can serve as a (secondary) standard of radiation in spectroscopic and radiometric measurements. The main advantades of the xenon lamp over other secondary standards such as the tungsten strip lamp and the anode of a carbon arc lamp are the high temperature of its discharge and the resulting strong radiation over a broad spectral range. (Auth.)

  18. High-pressure-high-temperature treatment of natural diamonds

    CERN Document Server

    Royen, J V

    2002-01-01

    The results are reported of high-pressure-high-temperature (HPHT) treatment experiments on natural diamonds of different origins and with different impurity contents. The diamonds are annealed in a temperature range up to 2000 sup o C at stabilizing pressures up to 7 GPa. The evolution is studied of different defects in the diamond crystal lattice. The influence of substitutional nitrogen atoms, plastic deformation and the combination of these is discussed. Diamonds are characterized at room and liquid nitrogen temperature using UV-visible spectrophotometry, Fourier transform infrared spectrophotometry and photoluminescence spectrometry. The economic implications of diamond HPHT treatments are discussed.

  19. High-pressure Brillouin scattering in a simple molecular system

    CERN Document Server

    Shimizu, H

    2002-01-01

    Recent developments in high-pressure in situ Brillouin spectroscopy of a simple molecular system are reviewed by demonstrating experimental and analytical methods for the study of acoustic velocities in any direction, adiabatic elastic constants, and elastic anisotropy. Detailed applications to solid argon (Ar) are presented, at pressures up to 70 GPa in a diamond anvil cell, using recently developed approaches that combine the method of in situ Brillouin spectroscopy, for a single crystal of Ar up to 4 GPa, and the envelope method applied to both longitudinal acoustic and transverse acoustic modes, for recrystallized Ar between 4 and 70 GPa.

  20. High pressure gas spheres for neutron and photon experiments

    Science.gov (United States)

    Rupp, G.; Petrich, D.; Käppeler, F.; Kaltenbaek, J.; Leugers, B.; Reifarth, R.

    2009-09-01

    High pressure gas spheres have been designed and successfully used in several nuclear physics experiments on noble gases. The pros and cons of this solution are the simple design and the high reliability versus the fact that the density is limited to 40-60% of liquid or solid gas samples. Originally produced for neutron capture studies at keV energies, the comparably small mass of the gas spheres were an important advantage, which turned out to be of relevance for other applications as well. The construction, performance, and operation of the spheres are described and examples for their use are presented.

  1. Plastic reactor suitable for high pressure and supercritical fluid electrochemistry

    DEFF Research Database (Denmark)

    Branch, Jack; Alibouri, Mehrdad; Cook, David A.

    2017-01-01

    The paper describes a reactor suitable for high pressure, particularly supercritical fluid, electrochemistry and electrodeposition at pressures up to 30 MPa at 115◦C. The reactor incorporates two key, new design concepts; a plastic reactor vessel and the use of o-ring sealed brittle electrodes....... These two innovations widen what can be achieved with supercritical fluid electrodeposition. The suitability of the reactor for electroanalytical experiments is demonstrated by studies of the voltammetry of decamethylferrocene in supercritical difluromethane and for electrodeposition is demonstrated...

  2. Does the previous diagnosis of arterial hypertension affect one's daily life? Pro-Saude Study.

    Science.gov (United States)

    Goffredo Filho, Gilberto Senechal de; Lopes, Claudia de Souza; Faerstein, Eduardo

    2013-12-01

    In addition to damaging several target organs, arterial hypertension may negatively impact patients' activities of daily living. Biological and behavioral mechanisms underlying such limitations have yet to be clarified. The objectives of this study were to investigate whether having been previously told of a hypertension diagnosis is associated with the frequency and duration of temporary limitations in activities of daily living, and whether these relationships differ by gender, age, or socioeconomic position. We analyzed sectional data from 2,666 participants (56% women; 55% with high school or lower schooling) at the baseline phase (1999 - 2001) of a longitudinal investigation of university employees in Rio de Janeiro, Brazil (Pró-Saúde Study), asking participants whether they had ever been diagnosed with hypertension by a health professional, if they had been unable to perform any activities of daily living due to a health problem in the previous 2 weeks, and for how many days that had occurred. Multinomial logistic regression models were fitted for the overall study population and for age, gender, educational level, and per capita household income strata. Associations between hypertension diagnosis and temporary limitations were not observed in the overall study population and in gender, education and income strata. However, there were higher odds of temporary limitations among participants aged 55 years old or more with hypertension diagnosis (adjusted OR = 9.5; 95%CI 1.5 - 58.6), regardless of blood pressure levels and use of antihypertensive medication. Elderly people may keep an attitude of higher vigilance regarding conditions or events potentially worsening their health status.

  3. Investigation of Methacrylic Acid at High Pressure Using Neutron Diffraction.

    Science.gov (United States)

    Marshall, William G; Urquhart, Andrew J; Oswald, Iain D H

    2015-09-10

    This article shows that pressure can be a low-intensity route to the synthesis of polymethacrylic acid. The exploration of perdeuterated methacrylic acid at high pressure using neutron diffraction reveals that methacrylic acid exhibits two polymorphic phase transformations at relatively low pressures. The first is observed at 0.39 GPa, where both phases were observed simultaneously and confirm our previous observations. This transition is followed by a second transition at 1.2 GPa to a new polymorph that is characterized for the first time. On increasing pressure, the diffraction pattern of phase III deteriorates significantly. On decompression phase III persists to 0.54 GPa before transformation to the ambient pressure phase. There is significant loss of signal after decompression, signifying that there has been a loss of material through polymerization. The orientation of the molecules in phase III provides insight into the possible polymerization reaction.

  4. Vacuum surface flashover and high pressure gas streamers

    International Nuclear Information System (INIS)

    Elizondo, J.M.; Krogh, M.L.; Smith, D.; Stolz, D.; Wright, S.N.

    1997-07-01

    Pre-breakdown current traces obtained during high pressure gas breakdown and vacuum surface flashover show similar signatures. The initial pre-breakdown current spike, a flat constant current phase, and the breakdown phase with voltage collapse and current surge differ mostly in magnitude. Given these similarities, a model, consisting of the initial current spike corresponding to a fast precursor streamer (ionization wave led by a photoionizing front), the flat current stage as the heating or glow phase, and the terminal avalanche and gap closure, is applied to vacuum surface flashover. A simple analytical approximation based on the resistivity changes induced in the vacuum and dielectric surface is presented. The approximation yields an excellent fit to pre-breakdown time delay vs applied field for previously published experimental data. A detailed kinetics model that includes surface and gas contributions is being developed based in the initial approximation

  5. Soft x-ray spectroscopy of high pressure liquid

    Science.gov (United States)

    Qiao, Ruimin; Xia, Yujian; Feng, Xuefei; Macdougall, James; Pepper, John; Armitage, Kevin; Borsos, Jason; Knauss, Kevin G.; Lee, Namhey; Allézy, Arnaud; Gilbert, Benjamin; MacDowell, Alastair A.; Liu, Yi-Sheng; Glans, Per-Anders; Sun, Xuhui; Chao, Weilun; Guo, Jinghua

    2018-01-01

    We describe a new experimental technique that allows for soft x-ray spectroscopy studies (˜100-1000 eV) of high pressure liquid (˜100 bars). We achieve this through a liquid cell with a 100 nm-thick Si3N4 membrane window, which is sandwiched by two identical O-rings for vacuum sealing. The thin Si3N4 membrane allows soft x-rays to penetrate, while separating the high-pressure liquid under investigation from the vacuum required for soft x-ray transmission and detection. The burst pressure of the Si3N4 membrane increases with decreasing size and more specifically is inversely proportional to the side length of the square window. It also increases proportionally with the membrane thickness. Pressures > 60 bars could be achieved for 100 nm-thick square Si3N4 windows that are smaller than 65 μm. However, above a certain pressure, the failure of the Si wafer becomes the limiting factor. The failure pressure of the Si wafer is sensitive to the wafer thickness. Moreover, the deformation of the Si3N4 membrane is quantified using vertical scanning interferometry. As an example of the performance of the high-pressure liquid cell optimized for total-fluorescence detected soft x-ray absorption spectroscopy (sXAS), the sXAS spectra at the Ca L edge (˜350 eV) of a CaCl2 aqueous solution are collected under different pressures up to 41 bars.

  6. A longitudinal study of plasma insulin and glucagon in women with previous gestational diabetes

    DEFF Research Database (Denmark)

    Damm, P; Kühl, C; Hornnes, P

    1995-01-01

    OBJECTIVE: To investigate whether plasma insulin or glucagon predicts later development of diabetes in women with gestational diabetes mellitus (GDM). RESEARCH DESIGN AND METHODS: The subjects studied were 91 women with diet-treated GDM and 33 healthy women. Plasma insulin and glucagon during a 50...... at follow-up (2 had insulin-dependent diabetes mellitus, 13 had non-insulin-dependent diabetes mellitus, and 12 had impaired glucose tolerance). Compared with the control subjects, women with previous GDM had relatively impaired insulin secretion (decreased insulinogenic index and delayed peak insulin...... for subsequent development of overt diabetes (logistic regression analysis). CONCLUSIONS: Women who develop GDM have a relative insulin secretion deficiency, the severity of which is predictive for later development of diabetes. Furthermore, our data indicate that their relatively reduced beta-cell function may...

  7. Case-control study for colorectal cancer genetic susceptibility in EPICOLON: previously identified variants and mucins

    International Nuclear Information System (INIS)

    Abulí, Anna; Morillas, Juan D; Rigau, Joaquim; Latorre, Mercedes; Fernández-Bañares, Fernando; Peña, Elena; Riestra, Sabino; Payá, Artemio; Jover, Rodrigo; Xicola, Rosa M; Llor, Xavier; Fernández-Rozadilla, Ceres; Carvajal-Carmona, Luis; Villanueva, Cristina M; Moreno, Victor; Piqué, Josep M; Carracedo, Angel; Castells, Antoni; Andreu, Montserrat; Ruiz-Ponte, Clara; Castellví-Bel, Sergi; Alonso-Espinaco, Virginia; Muñoz, Jenifer; Gonzalo, Victoria; Bessa, Xavier; González, Dolors; Clofent, Joan; Cubiella, Joaquin

    2011-01-01

    Colorectal cancer (CRC) is the second leading cause of cancer death in developed countries. Familial aggregation in CRC is also important outside syndromic forms and, in this case, a polygenic model with several common low-penetrance alleles contributing to CRC genetic predisposition could be hypothesized. Mucins and GALNTs (N-acetylgalactosaminyltransferase) are interesting candidates for CRC genetic susceptibility and have not been previously evaluated. We present results for ten genetic variants linked to CRC risk in previous studies (previously identified category) and 18 selected variants from the mucin gene family in a case-control association study from the Spanish EPICOLON consortium. CRC cases and matched controls were from EPICOLON, a prospective, multicenter, nationwide Spanish initiative, comprised of two independent stages. Stage 1 corresponded to 515 CRC cases and 515 controls, whereas stage 2 consisted of 901 CRC cases and 909 controls. Also, an independent cohort of 549 CRC cases and 599 controls outside EPICOLON was available for additional replication. Genotyping was performed for ten previously identified SNPs in ADH1C, APC, CCDN1, IL6, IL8, IRS1, MTHFR, PPARG, VDR and ARL11, and 18 selected variants in the mucin gene family. None of the 28 SNPs analyzed in our study was found to be associated with CRC risk. Although four SNPs were significant with a P-value < 0.05 in EPICOLON stage 1 [rs698 in ADH1C (OR = 1.63, 95% CI = 1.06-2.50, P-value = 0.02, recessive), rs1800795 in IL6 (OR = 1.62, 95% CI = 1.10-2.37, P-value = 0.01, recessive), rs3803185 in ARL11 (OR = 1.58, 95% CI = 1.17-2.15, P-value = 0.007, codominant), and rs2102302 in GALNTL2 (OR = 1.20, 95% CI = 1.00-1.44, P-value = 0.04, log-additive 0, 1, 2 alleles], only rs3803185 achieved statistical significance in EPICOLON stage 2 (OR = 1.34, 95% CI = 1.06-1.69, P-value = 0.01, recessive). In the joint analysis for both stages, results were only significant for rs3803185 (OR = 1.12, 95% CI = 1

  8. Case-control study for colorectal cancer genetic susceptibility in EPICOLON: previously identified variants and mucins

    Directory of Open Access Journals (Sweden)

    Moreno Victor

    2011-08-01

    Full Text Available Abstract Background Colorectal cancer (CRC is the second leading cause of cancer death in developed countries. Familial aggregation in CRC is also important outside syndromic forms and, in this case, a polygenic model with several common low-penetrance alleles contributing to CRC genetic predisposition could be hypothesized. Mucins and GALNTs (N-acetylgalactosaminyltransferase are interesting candidates for CRC genetic susceptibility and have not been previously evaluated. We present results for ten genetic variants linked to CRC risk in previous studies (previously identified category and 18 selected variants from the mucin gene family in a case-control association study from the Spanish EPICOLON consortium. Methods CRC cases and matched controls were from EPICOLON, a prospective, multicenter, nationwide Spanish initiative, comprised of two independent stages. Stage 1 corresponded to 515 CRC cases and 515 controls, whereas stage 2 consisted of 901 CRC cases and 909 controls. Also, an independent cohort of 549 CRC cases and 599 controls outside EPICOLON was available for additional replication. Genotyping was performed for ten previously identified SNPs in ADH1C, APC, CCDN1, IL6, IL8, IRS1, MTHFR, PPARG, VDR and ARL11, and 18 selected variants in the mucin gene family. Results None of the 28 SNPs analyzed in our study was found to be associated with CRC risk. Although four SNPs were significant with a P-value ADH1C (OR = 1.63, 95% CI = 1.06-2.50, P-value = 0.02, recessive, rs1800795 in IL6 (OR = 1.62, 95% CI = 1.10-2.37, P-value = 0.01, recessive, rs3803185 in ARL11 (OR = 1.58, 95% CI = 1.17-2.15, P-value = 0.007, codominant, and rs2102302 in GALNTL2 (OR = 1.20, 95% CI = 1.00-1.44, P-value = 0.04, log-additive 0, 1, 2 alleles], only rs3803185 achieved statistical significance in EPICOLON stage 2 (OR = 1.34, 95% CI = 1.06-1.69, P-value = 0.01, recessive. In the joint analysis for both stages, results were only significant for rs3803185 (OR = 1

  9. Advances in data reduction of high-pressure x-ray powder diffraction data from two-dimensional detectors: a case study of schafarzikite (FeSb2O4)

    Science.gov (United States)

    Hinrichsen, B.; Dinnebier, R. E.; Rajiv, P.; Hanfland, M.; Grzechnik, A.; Jansen, M.

    2006-06-01

    Methods have been developed to facilitate the data analysis of multiple two-dimensional powder diffraction images. These include, among others, automatic detection and calibration of Debye-Scherrer ellipses using pattern recognition techniques, and signal filtering employing established statistical procedures like fractile statistics. All algorithms are implemented in the freely available program package Powder3D developed for the evaluation and graphical presentation of large powder diffraction data sets. As a case study, we report the pressure dependence of the crystal structure of iron antimony oxide FeSb2O4 (p<=21 GPa, T = 298 K) using high-resolution angle dispersive x-ray powder diffraction. FeSb2O4 shows two phase transitions in the measured pressure range. The crystal structures of all modifications consist of frameworks of Fe2+O6 octahedra and irregular Sb3+O4 polyhedra. At ambient conditions, FeSb2O4 crystallizes in space group P42/mbc (phase I). Between p = 3.2 GPa and 4.1 GPa it exhibits a displacive second order phase transition to a structure of space group P 21/c (phase II, a = 5.7792(4) Å, b = 8.3134(9) Å, c = 8.4545(11) Å, β = 91.879(10)°, at p = 4.2 GPa). A second phase transition occurs between p = 6.4 GPa and 7.4 GPa to a structure of space group P42/m (phase III, a = 7.8498(4) Å, c = 5.7452(5) Å, at p = 10.5 GPa). A nonlinear compression behaviour over the entire pressure range is observed, which can be described by three Vinet equations in the ranges from p = 0.52 GPa to p = 3.12 GPa, p = 4.2 GPa to p = 6.3 GPa and from p = 7.5 GPa to p = 19.8 GPa. The extrapolated bulk moduli of the high-pressure phases were determined to K0 = 49(2) GPa for phase I, K0 = 27(3) GPa for phase II and K0 = 45(2) GPa for phase III. The crystal structures of all phases are refined against x-ray powder data measured at several pressures between p = 0.52 GPa, and 10.5 GPa.

  10. Laboratory Investigation of High Pressure Survival in Shewanella oneidensis MR-1 into the GigaPascal Pressure Range

    Directory of Open Access Journals (Sweden)

    Rachael eHazael

    2014-11-01

    Full Text Available The survival of Shewanella oneidensis MR-1 at up to 1500 MPa was investigated by laboratory studies involving exposure to high pressure followed by evaluation of survivors as the number (N of colony forming units (CFU that could be cultured following recovery to ambient conditions. Exposing the wild type bacteria to 250 MPa resulted in only a minor (0.7 log N units drop in survival compared with the initial concentration of 108 cells/ml. Raising the pressure to above 500 MPa caused a large reduction in the number of viable cells observed following recovery to ambient pressure. Additional pressure increase caused a further decrease in survivability, with approximately 102 CFU/ml recorded following exposure to 1000 MPa (1 GPa and 1.5 GPa. Pressurizing samples from colonies resuscitated from survivors that had been previously exposed to high pressure resulted in substantially greater survivor counts. Experiments were carried out to examine potential interactions between pressure and temperature variables in determining bacterial survival. One generation of survivors previously exposed to 1 GPa was compared with wild type samples to investigate survival between 37°C to 8°C. The results did not reveal any coupling between acquired high pressure resistance and temperature effects on growth.

  11. NATO Advanced Research Workshop on Frontiers of High-Pressure Research

    CERN Document Server

    Etters, Richard

    1991-01-01

    The role of high pressure experiments in the discovery of supercon­ ducting materials with a T. above liquid nitrogen temperature has demon­ strated the importance of such experiments. The same role holds true in the tailoring of materials for optoelectronic devices. In addition, much progress has been made recently in the search for metallic hydro­ gen, and the application of high pressure in polymer research has brought forth interesting results. These facts together with the suc­ cess of previous small size meetings (such as the "First International Conference on the Physics of Solids at High Pressure", held in 1965 in Tucson, Arizona, U. S. A. ; "High Pressure and Low Temperature Physics", held in 1977 in Cleveland, Ohio, U. S. A. ; and "Physics of Solids Under High Pressure", held in 1981 in bad Honnef, Germany), motivated us to organize a workshop with emphasis on the newest results and trends in these fields of high pressure research. Furthermore, it was intended to mix experienced and young scien�...

  12. Raman Spectroscopy of Serpentine and Reaction Products at High Pressure Using a Diamond Anvil Cell

    Science.gov (United States)

    Burgess, K.; Zinin, P.; Odake, S.; Fryer, P.; Hellebrand, E.

    2012-12-01

    Serpentine is one of the most abundant hydrous phases in the altered subducting plate, and contributes a large portion of the water flux in subduction zones. Measuring and understanding the structural changes in serpentine with pressure aids our understanding of the processes ongoing in oceanic crust and subduction zones. We have conducted high-pressure/high-temperature experiments on serpentine and its dehydration reaction products using a diamond anvil cell. We used the multifunctional in-situ measurement system equipped with a Raman device and laser heating system at the University of Hawaii. Well-characterized natural serpentinite was used in the study. Pressure was determined using the shift of the fluorescence line of a ruby placed next to the sample. Raman spectra of serpentine were obtained at higher pressures than previously published, up to 15 GPa; the peak shift with pressure fits the model determined by Auzende et al. [2004] at lower pressures. Heating was done at several different pressures up to 20 GPa, and reaction products were identified using Raman. Micro-Raman techniques allow us to determine reaction progress and heterogeneity within natural samples containing olivine and serpentine. Auzende, A-L., I. Daniel, B. Reynard, C. Lemaire, F. Guyot (2004). High-pressure behavior of serpentine minerals: a Raman spectroscopic study. Phys. Chem. Minerals 31 269-277.

  13. Neutron powder diffraction under high pressure at J-PARC

    International Nuclear Information System (INIS)

    Utsumi, Wataru; Kagi, Hiroyuki; Komatsu, Kazuki; Arima, Hiroshi; Nagai, Takaya; Okuchi, Takuo; Kamiyama, Takashi; Uwatoko, Yoshiya; Matsubayashi, Kazuyuki; Yagi, Takehiko

    2009-01-01

    It is expected that high-pressure material science and the investigation of the Earth's interior will progress greatly using the high-flux pulse neutrons of J-PARC. In this article, we introduce our plans for in situ neutron powder diffraction experiments under high pressure at J-PARC. The use of three different types of high-pressure devices is planned; a Paris-Edinburgh cell, a new opposed-anvil cell with a nano-polycrystalline diamond, and a cubic anvil high-pressure apparatus. These devices will be brought to the neutron powder diffraction beamlines to conduct a 'day-one' high-pressure experiment. For the next stage of research, we propose construction of a dedicated beamline for high-pressure material science. Its conceptual designs are also introduced here.

  14. Bonding Properties of Aluminum Nitride at High Pressure.

    Science.gov (United States)

    Liu, Zhao; Li, Da; Wei, Shuli; Wang, Wenjie; Tian, Fubo; Bao, Kuo; Duan, Defang; Yu, Hongyu; Liu, Bingbing; Cui, Tian

    2017-07-03

    Exploring the bonding properties and polymerization mechanism of stable polymeric nitrogen phases is the main goal of our high-pressure study. The pressure versus composition phase diagram of the Al-N system is established. In addition to the known Fm3̅m phase of AlN, a notable monoclinic phase with N 6 6- anion polymeric nitrogen chains for AlN 3 in the pressure range from 43 to 85 GPa is predicted. Its energy density is up to 2.75 kJ·g -1 , and the weight ratio of nitrogen is nearly 61%, which make it potentially interesting for the industrial applications as a high energy density material. The high-pressure studies of atomic and electronic structures in this predicted phase reveal that the formation of N 6 6- anion is driven by the sp 2 hybridization of nitrogen atoms. The resonance effect between alternating π-bonds and σ-bonds in polymeric nitrogen chains are all responsible for the structural stability. Because of the electrons transfer from aluminums to polymeric nitrogen chains, there is a pseudogap in the electronic structures of AlN 3 . The N_p electrons form π-type chemical bonds with the neighboring atoms, resulting in the delocalization of π electrons and charge transfer in polymeric nitrogen chains. Furthermore, disparities of charge density distribution between nitrogen atoms in polymeric nitrogen chains are the principal reason for the metallicity.

  15. Blue emitting organic semiconductors under high pressure: status and outlook

    Science.gov (United States)

    Knaapila, Matti; Guha, Suchismita

    2016-06-01

    This review describes essential optical and emerging structural experiments that use high GPa range hydrostatic pressure to probe physical phenomena in blue-emitting organic semiconductors including π-conjugated polyfluorene and related compounds. The work emphasizes molecular structure and intermolecular self-organization that typically determine transport and optical emission in π-conjugated oligomers and polymers. In this context, hydrostatic pressure through diamond anvil cells has proven to be an elegant tool to control structure and interactions without chemical intervention. This has been highlighted by high pressure optical spectroscopy whilst analogous x-ray diffraction experiments remain less frequent. By focusing on a class of blue-emitting π-conjugated polymers, polyfluorenes, this article reviews optical spectroscopic studies under hydrostatic pressure, addressing the impact of molecular and intermolecular interactions on optical excitations, electron-phonon interaction, and changes in backbone conformations. This picture is connected to the optical high pressure studies of other π-conjugated systems and emerging x-ray scattering experiments from polyfluorenes which provides a structure-property map of pressure-driven intra- and interchain interactions. Key obstacles to obtain further advances are identified and experimental methods to resolve them are suggested.

  16. Blue emitting organic semiconductors under high pressure: status and outlook.

    Science.gov (United States)

    Knaapila, Matti; Guha, Suchismita

    2016-06-01

    This review describes essential optical and emerging structural experiments that use high GPa range hydrostatic pressure to probe physical phenomena in blue-emitting organic semiconductors including π-conjugated polyfluorene and related compounds. The work emphasizes molecular structure and intermolecular self-organization that typically determine transport and optical emission in π-conjugated oligomers and polymers. In this context, hydrostatic pressure through diamond anvil cells has proven to be an elegant tool to control structure and interactions without chemical intervention. This has been highlighted by high pressure optical spectroscopy whilst analogous x-ray diffraction experiments remain less frequent. By focusing on a class of blue-emitting π-conjugated polymers, polyfluorenes, this article reviews optical spectroscopic studies under hydrostatic pressure, addressing the impact of molecular and intermolecular interactions on optical excitations, electron-phonon interaction, and changes in backbone conformations. This picture is connected to the optical high pressure studies of other π-conjugated systems and emerging x-ray scattering experiments from polyfluorenes which provides a structure-property map of pressure-driven intra- and interchain interactions. Key obstacles to obtain further advances are identified and experimental methods to resolve them are suggested.

  17. High pressure neutron and X-ray diffraction at low temperatures

    International Nuclear Information System (INIS)

    Ridley, Christopher J.; Kamenev, Konstantin V.

    2014-01-01

    This paper presents a review of techniques and considerations in the design and construction of high pressure, low temperature diffraction experiments. Also intended as an introductory text to new high pressure users, the crucial aspects of pressure cell design are covered. The general classification of common designs, and a discussion into the key beam interaction, mechanical, and thermal properties of commonly used materials is given. The advantages of different materials and high pressure cell classifications are discussed, and examples of designs developed for low temperature diffraction studies are presented, and compared. (orig.)

  18. A cubic-anvil high-pressure device for pulsed neutron powder diffraction.

    Science.gov (United States)

    Abe, J; Arakawa, M; Hattori, T; Arima, H; Kagi, H; Komatsu, K; Sano-Furukawa, A; Uwatoko, Y; Matsubayashi, K; Harjo, S; Moriai, A; Ito, T; Aizawa, K; Arai, M; Utsumi, W

    2010-04-01

    A compact cubic-anvil high-pressure device was developed for in situ neutron powder diffraction studies. In this device, a cubic shaped pressure medium is compressed by six anvils, and neutron beams pass through gaps between the anvils. The first high-pressure experiment using this device was conducted at J-PARC and clearly showed the neutron diffraction patterns of Pb. Combining the cubic-anvil high-pressure device with a pulsed neutron source will prove to be a useful tool for neutron diffraction experiments.

  19. A study about the interest and previous contact of high school students with Astronomy

    Science.gov (United States)

    Carvalho, C. L.; Zanitti, M. H. R.; Felicidade, B. L.; Gomes, A. D. T.; Dias, E. W.; Coelho, F. O.

    2016-04-01

    The currently problems in Astronomy teaching in Brazilian Basic Education contrast with the space, and the popularity that astronomical themes have in various media in the country. In this work, we present the results of a study about the interest, and previous contact of high school students from a public school in the city of "São João del-Rei"/MG with topics related to Astronomy. The study and the pedagogical intervention were carried out by students of the PIBID/CAPES/UFSJ. The intervention was performed through an oral exposition with the students' participation, followed by the use of the Stellarium program. The results suggest the majority of students surveyed are interested in Astronomy, and have had some contact with the area. However, some inconsistencies in their responses were identified and examined. The implications for research and for Astronomy Education are discussed. We also make some considerations about relationship between the lack of specific knowledge and the misinformation as one possible reason for the little interest of students in various areas of Science.

  20. Safety regulation on high-pressure gas and gas business

    International Nuclear Information System (INIS)

    Kim, Du Yeoung; An, Dae Jun

    1978-09-01

    This book is divided into two parts. The first part introduces safety regulation on high-pressure gas, enforcement ordinance on safety regulation about high-pressure gas and enforcement regulation on safety regulation about high-pressure gas. The second part indicates regulations on gas business such as general rules, gas business gas supplies, using land, supervision, supple mentary rules and penalty. It has two appendixes on expected questions and questions during last years.

  1. Biosystematic studies on Dactylis L. l. Review of the previous studies. 1.2. Cytology, genetics, experimental studies, and evolution

    Directory of Open Access Journals (Sweden)

    Marta Mizianty

    2014-01-01

    Full Text Available In this paper the author presents a review of the previous studies on Dactylis L., dealing with cytology,genetics, experimental studies and evolution. Following cytotypes of Dactylis are distributed mostly in Central Europe: 16 diploids, 7 tetraploids and also 2 hexaploids in North Africa. Some aneuploids and accessory chromosomes were also found in this genus. Data dealing with karyotypes of some taxa, and geographical distribution of cytotypes are also listed. Selected problems concerning crossing within diploids as well as tetraploids and also between diploids and teraploids were presented. Some opinions regarding the evolution in the genus Dactylis were also demonstrated. In all these hypotheses the following diploids are considered to be the oldest: D. smithii Link subsp. smithii, D. g. subsp. aschersoniana (Greabn. Thell. and D. g. subsp. himalayensis Dom.

  2. Nanocomposite Thermolectric Materials by High Pressure Powder Consolidation Manufacturing Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In response to NASA's need to develop advanced nanostructured thermolectric materials, UTRON is proposing an innovative high pressure powder consolidation...

  3. Thermal and high pressure inactivation kinetics of blueberry peroxidase.

    Science.gov (United States)

    Terefe, Netsanet Shiferaw; Delon, Antoine; Versteeg, Cornelis

    2017-10-01

    This study for the first time investigated the stability and inactivation kinetics of blueberry peroxidase in model systems (McIlvaine buffer, pH=3.6, the typical pH of blueberry juice) during thermal (40-80°C) and combined high pressure-thermal processing (0.1-690MPa, 30-90°C). At 70-80°C, the thermal inactivation kinetics was best described by a biphasic model with ∼61% labile and ∼39% stable fractions at temperature between 70 and 75°C. High pressure inhibited the inactivation of the enzyme with no inactivation at pressures as high as 690MPa and temperatures less than 50°C. The inactivation kinetics of the enzyme at 60-70°C, and pressures higher than 500MPa was best described by a first order biphasic model with ∼25% labile fraction and 75% stable fraction. The activation energy values at atmospheric pressure were 548.6kJ/mol and 324.5kJ/mol respectively for the stable and the labile fractions. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

  4. Superconductivity in the high-pressure phase of bismuth

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Philip A.C.; Semeniuk, Konstantin; Grosche, F. Malte [Department of Physics, Cavendish Laboratory, University of Cambridge (United Kingdom)

    2016-07-01

    At pressures above 27 kbar, elemental bismuth adopts a highly unusual incommensurate host-guest structure. This structure combines two distinct, interpenetrating crystal lattices and consequently lacks discrete translational symmetry. Although similar high pressure structures have been observed in other elements, their electronic properties have not been investigated in detail. The moderate pressure required to induce the host-guest phase in bismuth presents a favourable opportunity for comprehensive electrical transport studies. The high-pressure host-guest phase of bismuth, termed Bi-III, is known to be superconducting with a transition temperature of around 7 K, but the details of its superconducting and normal state properties are comparatively little explored. We report resistivity and magnetisation measurements in the Bi-III phase in fields up to 9 T and temperatures down to 120 mK. We find evidence for a strikingly high critical field and an unusual temperature dependence of the resistivity above the superconducting transition. We discuss our findings in the context of theoretical descriptions of host-guest materials.

  5. Condensation heat transfer on natural convection at the high pressure

    International Nuclear Information System (INIS)

    Jong-Won, Kim; Hyoung-Kyoun, Ahn; Goon-Cherl, Park

    2007-01-01

    The Regional Energy Research Institute for the Next Generation is to develop a small scale electric power system driven by an environment-friendly and stable small nuclear reactor. REX-10 has been developed to assure high system safety in order to be placed in densely populated region and island. REX-10 adopts the steam-gas pressurizer to assure the inherent safety. The thermal-hydraulic phenomena in the steam-gas pressurizer are very complex. Especially, the condensation heat transfer with noncondensable gas on the natural convection is important to evaluate the pressurizer behavior. However, there have been few investigations on the condensation in the presence of noncondensable gas at the high pressure. In this study, the theoretical model is developed to estimate the condensation heat transfer at the high pressure using heat and mass transfer analogy. The analysis results show good agreement with correlations and experimental data. It is found that the condensation heat transfer coefficient increases as the total pressure increases or the mass fraction of the non-condensable gas decreases. In addition, the heat transfer coefficient no more increases over the specific pressure

  6. High pressure synthesis of BiS2

    DEFF Research Database (Denmark)

    Søndergaard-Pedersen, Simone; Nielsen, Morten Bormann; Bremholm, Martin

    crystal structures and electrical properties.1,2 Up until now, the most sulfur rich phase in the Bi-S phase diagram was Bi2S3.3 For BiS2 the Bi atoms have anisotropic charge distribution and more complex structures are expected when comparing the layered structures of transition metal dichalcogenides....... The possibilities of using high pressure synthesis to discover new phases in the Bi-S binary system were investigated as early as the 1960’s.4 The research led to discovery of a compound with BiS2 stoichiometry, but no structure solution of BiS2 was reported. A reason behind making this new phase is to study...... the physical properties since the related compound Bi2S3 is known to be a thermoelectric material.5 In this research the BiS2 compound was synthesized by a high pressure and high temperature method using a multi-anvil large volume press and the structure was solved by single crystal diffraction. The structure...

  7. High-pressure cell for simultaneous dielectric and neutron spectroscopy

    Science.gov (United States)

    Sanz, Alejandro; Hansen, Henriette Wase; Jakobsen, Bo; Pedersen, Ib H.; Capaccioli, Simone; Adrjanowicz, Karolina; Paluch, Marian; Gonthier, Julien; Frick, Bernhard; Lelièvre-Berna, Eddy; Peters, Judith; Niss, Kristine

    2018-02-01

    In this article, we report on the design, manufacture, and testing of a high-pressure cell for simultaneous dielectric and neutron spectroscopy. This cell is a unique tool for studying dynamics on different time scales, from kilo- to picoseconds, covering universal features such as the α relaxation and fast vibrations at the same time. The cell, constructed in cylindrical geometry, is made of a high-strength aluminum alloy and operates up to 500 MPa in a temperature range between roughly 2 and 320 K. In order to measure the scattered neutron intensity and the sample capacitance simultaneously, a cylindrical capacitor is positioned within the bore of the high-pressure container. The capacitor consists of two concentric electrodes separated by insulating spacers. The performance of this setup has been successfully verified by collecting simultaneous dielectric and neutron spectroscopy data on dipropylene glycol, using both backscattering and time-of-flight instruments. We have carried out the experiments at different combinations of temperature and pressure in both the supercooled liquid and glassy state.

  8. The high pressure PVT properties of deuterium oxide

    International Nuclear Information System (INIS)

    Fine, R.A.; Millero, F.J.

    1975-01-01

    The high pressure isothermal compressibilities of deuterium oxide from 5 to 100 degreeC and 0 to 1000 bars applied or gauge pressure were determined from sound speed data. These compressibilities were used to derive an equation of state of the form V 0 P/(V 0 - V/supP/) = B + A 1 P + A 2 P 2 , where V 0 and V/supP/ are the specific volumes at an applied pressure of zero and P; and B, A 1 , and A 2 are polynomial functions of temperature. The compressibilities derived from this equation of state are consistent with those derived from the sound speed data to plus-or-minus0.016times10 -6 bar -1 over the entire pressure and temperature range (this is equivalent to approx.0.2 m sec -1 in sound speed). The 1 atm sound-derived compressibilities agree on the average to plus-or-minus0.06times10 -6 bar -1 with the direct measurements of Millero and Lepple. The P--V--T data from the sound-derived equation are compared with the high pressure work of Bridgman, Kesselman, Juza et al., and Emmet and Millero. Good agreement (average deviation of plus-or-minus28times10 -6 cm 3 g -1 ) was found with the recent specific volume measurements of Emmet and Millero. The P--V--T properties of D 2 O are compared to pure water. D 2 O and H 2 O are shown to follow similar trends. Contrary to previous reports, the D 2 O/H 2 O ratios of the specific volumes and specific heats are shown to be functions of both temperature and pressure

  9. The gem anvil cell: high-pressure behaviour of diamond and related materials

    CERN Document Server

    Xu Jian; Hemley, R J

    2002-01-01

    The moissanite anvil cell has been used to study the high-pressure behaviour of diamond. The first-order Raman shift of diamond shows a strong dependence on hydrostaticity, with very different pressure dependences observed under hydrostatic and non-hydrostatic conditions. The shift of the second-order Raman band under hydrostatic pressures was determined for the first time. Sapphire has almost no peaks above 1000 cm sup - sup 1 in the Raman spectrum and no absorption in the ultraviolet range; it is therefore especially useful for studies in those spectral regions. A sapphire anvil cell was used in a study of graphite up to 24 GPa. A phase transition was found near 18 GPa, consistent with previous reports, and no peaks characteristic of diamond in the 1330 cm sup - sup 1 range were found, indicating that the phase is not diamond.

  10. The gem anvil cell: high-pressure behaviour of diamond and related materials

    International Nuclear Information System (INIS)

    Xu Jian; Mao Hokwang; Hemley, Russell J

    2002-01-01

    The moissanite anvil cell has been used to study the high-pressure behaviour of diamond. The first-order Raman shift of diamond shows a strong dependence on hydrostaticity, with very different pressure dependences observed under hydrostatic and non-hydrostatic conditions. The shift of the second-order Raman band under hydrostatic pressures was determined for the first time. Sapphire has almost no peaks above 1000 cm -1 in the Raman spectrum and no absorption in the ultraviolet range; it is therefore especially useful for studies in those spectral regions. A sapphire anvil cell was used in a study of graphite up to 24 GPa. A phase transition was found near 18 GPa, consistent with previous reports, and no peaks characteristic of diamond in the 1330 cm -1 range were found, indicating that the phase is not diamond

  11. Investigating cavity pressure behavior in high-pressure RTM process variants

    Science.gov (United States)

    Rosenberg, P.; Chaudhari, R.; Karcher, M.; Henning, F.; Elsner, P.

    2014-05-01

    The paper addresses new variants of the high pressure resin transfer molding (HP-RTM) process namely high pressure injection RTM (HP-IRTM) and high pressure compression RTM (HP-CRTM) for manufacturing of carbon fiber reinforced composites with high fiber volume content. Both these processes utilize high-pressure RTM equipment for precise dosing and mixing of highly reactive epoxy resin and amine hardener with relatively high throughput rates. The paper addresses results of a study which investigated cavity pressure measurement for both the HP-RTM process variants using a specially designed highpressure RTM mold. The investigations indicate that the cavity pressure built up is a characteristic of the selected process variant. Further the relationship between the applied press force and the cavity pressure in HP-CRTM process was studied.

  12. Advanced setup for high-pressure and low-temperature neutron diffraction at hydrostatic conditions

    International Nuclear Information System (INIS)

    Lokshin, Konstantin A.; Zhao Yusheng

    2005-01-01

    We describe a design of the experimental setup for neutron diffraction studies at low temperatures and hydrostatic pressure. The significant benefit of the setup, compared to the previous methods, is that it makes possible the simultaneous collection of neutrons diffracted at the 30 deg. -150 deg. range with no contamination by the primary scattering from the sample surroundings and without cutting out the incident and diffracted beams. The suggested design is most useful for third-generation time-of-flight diffractometers and constant wavelength instruments. Application of the setup expands the capabilities of high-pressure neutron diffraction, allowing time-resolved kinetics and structural studies, multihistogram Rietveld, and pair distribution function and texture analyses. The high efficiency of the setup was proven for the HIPPO diffractometer at Los Alamos Neutron Science Center under pressures up to 10 kbar and temperatures from 4 to 300 K

  13. CARS Diagnostics of High Pressure Combustion - 2. Measurements of NO, H2O and High Pressure Flames

    Science.gov (United States)

    1985-12-01

    R85-956328-F CARS DIAGNOSTICS OF r HIGH PRESSURE COMBUSTION -I MEASUREMENTS OF NO, H 0 AND HIGH PRESSURE FLAMES Final Report J.H. Stufflebeam DTIC I7...High Pressure Flames Final Report ~ 5%~ J. H. Stufflebeam J. A. Shirley December 1985 𔃿** U. S. Army Research Office Contract: DAAG29-83-C-OOO1...ClaIiation, CARS Diagnostics of High Pressure Combustion II 12. PERSONAL AUTHOR(S) Stufflebeam , 7. H., ShirleyJA 113a. TYPE OF REPORT 13b. TIME COVERED

  14. Advances in high pressure science and technology: proceedings of the fourth national conference on high pressure science and technology

    International Nuclear Information System (INIS)

    Yousuf, Mohammad; Subramanian, N.; Govinda Rajan, K.

    1997-09-01

    The proceedings of the fourth National Conference on High Pressure Science and Technology covers a wide area of research and development activities in the field of high pressure science and technology, broadly classified into the following themes: mechanical behaviour of materials; instrumentation and methods in high pressure research; pressure calibration, standards and safety aspects; phase transitions; shock induced reactions; mineral science, geophysics, geochemistry and planetary sciences; optical, electronic and transport properties; synthesis of materials; soft condensed matter physics and liquid crystals; computational methods in high pressure research. Papers relevant to INIS are indexed separately

  15. Giant high-pressure pulmonary artery aneurysm in an elderly patient with chronic obstructive pulmonary disease.

    Science.gov (United States)

    Morais, Sandra A; Oliveira, Hugo M; de Almeida, José R; Eiras, Eduardo; Silva, Ana Catarina; Gavina, Cristina

    2016-03-01

    The authors report the case of a 74-year-old man, with a history of chronic obstructive pulmonary disease (COPD), GOLD grade 3, stable for the past two decades, who was admitted to our center with severe right heart failure. The chest radiograph showed moderate heart enlargement mainly of the right atrium and pulmonary artery, similar to previous chest radiographs in the previous 20 years. The transthoracic echocardiogram showed a pulmonary artery aneurysm (PAA), dilatation of the right chambers with pulmonary artery systolic pressure of 52 mmHg, and preserved right ventricular systolic function. A thoracic computed tomography scan confirmed the presence of a giant PAA 72 mm in diameter. The patient was started on high-dose diuretics, with significant clinical improvement. After optimization of medical therapy right heart catheterization was carried out with the patient in optimal clinical condition, which revealed mild precapillary pulmonary hypertension with a mean pulmonary artery pressure of 26 mmHg. On the basis of the clinical and imaging findings a stable, giant, high-pressure, PAA was diagnosed secondary to pulmonary hypertension induced by COPD, with a 20-year follow-up without need for surgical repair, which helped in our decision to maintain medical surveillance. The recent onset of heart failure is explained by the unfavorable evolution of COPD. This case may change the attitude expressed in previous studies favoring the choice of an invasive approach to treat giant high-pressure PAAs, instead supporting the maintenance of medical treatment. Copyright © 2016 Sociedade Portuguesa de Cardiologia. Published by Elsevier España. All rights reserved.

  16. Novel stable structure of Li3PS4 predicted by evolutionary algorithm under high-pressure

    Directory of Open Access Journals (Sweden)

    S. Iikubo

    2018-01-01

    Full Text Available By combining theoretical predictions and in-situ X-ray diffraction under high pressure, we found a novel stable crystal structure of Li3PS4 under high pressures. At ambient pressure, Li3PS4 shows successive structural transitions from γ-type to β-type and from β-type to α type with increasing temperature, as is well established. In this study, an evolutionary algorithm successfully predicted the γ-type crystal structure at ambient pressure and further predicted a possible stable δ-type crystal structures under high pressure. The stability of the obtained structures is examined in terms of both static and dynamic stability by first-principles calculations. In situ X-ray diffraction using a synchrotron radiation revealed that the high-pressure phase is the predicted δ-Li3PS4 phase.

  17. The biomechanics of running in athletes with previous hamstring injury: A case-control study.

    Science.gov (United States)

    Daly, C; Persson, U McCarthy; Twycross-Lewis, R; Woledge, R C; Morrissey, D

    2016-04-01

    Hamstring injury is prevalent with persistently high reinjury rates. We aim to inform hamstring rehabilitation by exploring the electromyographic and kinematic characteristics of running in athletes with previous hamstring injury. Nine elite male Gaelic games athletes who had returned to sport after hamstring injury and eight closely matched controls sprinted while lower limb kinematics and muscle activity of the previously injured biceps femoris, bilateral gluteus maximus, lumbar erector spinae, rectus femoris, and external oblique were recorded. Intergroup comparisons of muscle activation ratios and kinematics were performed. Previously injured athletes demonstrated significantly reduced biceps femoris muscle activation ratios with respect to ipsilateral gluteus maximus (maximum difference -12.5%, P = 0.03), ipsilateral erector spinae (maximum difference -12.5%, P = 0.01), ipsilateral external oblique (maximum difference -23%, P = 0.01), and contralateral rectus femoris (maximum difference -22%, P = 0.02) in the late swing phase. We also detected sagittal asymmetry in hip flexion (maximum 8°, P = 0.01), pelvic tilt (maximum 4°, P = 0.02), and medial rotation of the knee (maximum 6°, P = 0.03) effectively putting the hamstrings in a lengthened position just before heel strike. Previous hamstring injury is associated with altered biceps femoris associated muscle activity and potentially injurious kinematics. These deficits should be considered and addressed during rehabilitation. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  18. 2D IR spectroscopy of high-pressure phases of ice

    NARCIS (Netherlands)

    Tran, Halina; Cunha, Ana V.; Shephard, Jacob J.; Shalit, Andrey; Hamm, Peter; Jansen, Thomas L. C.; Salzmann, Christoph G.

    2017-01-01

    We present experimental and simulated 2D IR spectra of some high-pressure forms of isotope-pure D2O ice and compare the results to those of ice Ih published previously [F. Perakis and P. Hamm, Phys. Chem. Chem. Phys. 14, 6250 (2012); L. Shi et al., ibid. 18, 3772 (2016)]. Ice II, ice V, and ice XIII

  19. Thermal elastic properties of liquid Fe-C at high pressure

    Science.gov (United States)

    Shimoyama, Y.; Terasaki, H. G.; Urakawa, S.; Takubo, Y.; Watanuki, T.; Katayama, Y.; Kondo, T.

    2015-12-01

    Planetary outer core contains some light elements and these elements affect thermo-elastic parameters of pure iron. The effect of light elements on density and bulk modulus of liquid iron is necessary for estimating of these core compositions. Sound velocity of liquid iron alloys is also important for identifying light elements in the core by comparison with observed seismic data. We have measured sound velocity and density of liquid Fe-C simultaneously at high pressure. High pressure experiments were performed using a DIA-type cubic anvil press (SMAP-180) at BL22XU beamline, SPring-8 synchrotron in Japan. Sound velocity (VP) was measured using pulse-echo overlapping method (Higo et al., 2009). Density (ρ) was measured using X-ray absorption method (Katayama et al., 1993). We measured velocity and density of liquid Fe-C between 1.1-5.8 GPa and 1480-1700 K. Obtained density and velocity of Fe-C was found to increase with pressure. This study shows the VP of liquid Fe-C decreased with increasing temperature. Previous study of liquid Fe-S shows little change with increasing temperature at all pressure conditions (Nishida et al., 2013, Jing et al., 2014). We fit the relationship between VP and pressure using Murnaghan's equation of state. We obtained KS0 = 102.5(1.2) GPa, K'S = 5.2(0.4) at 1700 K. Comparison of the present data with previous study, KS is similar to liquid Fe but liquid Fe-S is small. We compared the relation between density and sound velocity of liquid Fe-C. We have found that the behavior of liquid Fe-C is similar to that of liquid Fe in the Birch's plot. The effect of carbon on liquid Fe is small on Birch's plot.

  20. High-pressure synchrotron Mössbauer and X-ray diffraction studies: Exploring the structure-related valence fluctuation in EuNi{sub 2}P{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Li, Chunyu [Center for High Pressure Science and Technology Advanced Research, Shanghai 201203 (China); Natural Science Research Center, Academy of Fundamental and Interdisciplinary Sciences, Harbin Institute of Technology, Harbin 150080 (China); Yu, Zhenhai, E-mail: yuzh@hpstar.ac.cn [Center for High Pressure Science and Technology Advanced Research, Shanghai 201203 (China); Natural Science Research Center, Academy of Fundamental and Interdisciplinary Sciences, Harbin Institute of Technology, Harbin 150080 (China); Bi, Wenli [Advanced Photon Source, Argonne National Laboratory, Argonne, IL 60439 (United States); Department of Geology, University of Illinois at Urbana-Champaign, Urbana, IL 61801 (United States); Zhao, Jiyong; Hu, Michael Y. [Advanced Photon Source, Argonne National Laboratory, Argonne, IL 60439 (United States); Zhao, Jinggeng [Natural Science Research Center, Academy of Fundamental and Interdisciplinary Sciences, Harbin Institute of Technology, Harbin 150080 (China); Wu, Wei [Beijing National Lab for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China); Luo, Jianlin [Beijing National Lab for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China); Collaborative Innovation Center of Quantum Matter, Beijing 100190 (China); Yan, Hao, E-mail: yanhao@hpstar.ac.cn [Center for High Pressure Science and Technology Advanced Research, Shanghai 201203 (China); Alp, Esen E. [Advanced Photon Source, Argonne National Laboratory, Argonne, IL 60439 (United States); Liu, Haozhe, E-mail: haozhe.liu@hpstar.ac.cn [Center for High Pressure Science and Technology Advanced Research, Shanghai 201203 (China); Natural Science Research Center, Academy of Fundamental and Interdisciplinary Sciences, Harbin Institute of Technology, Harbin 150080 (China)

    2016-11-15

    The high-pressure effect on valence fluctuation of the ThCr{sub 2}Si{sub 2}-type intermetallic compound EuNi{sub 2}P{sub 2} has been investigated using in situ synchrotron Mössbauer spectroscopy (SMS). The isomer shift of {sup 151}Eu in EuNi{sub 2}P{sub 2} increases monotonically with increasing pressure up to 50 GPa, suggesting a valence transition of the Eu from mixed toward trivalent. The synchrotron angle-dispersive X-ray diffraction (AD-XRD) experiment shows that EuNi{sub 2}P{sub 2} remains in the tetragonal structure up to 32.5 GPa at room temperature. We propose that the evolutions of bonding distance with pressure have an obvious effect on the valence fluctuation.

  1. Structural investigation of ribonuclease A conformational preferences using high pressure protein crystallography

    Energy Technology Data Exchange (ETDEWEB)

    Kurpiewska, Katarzyna, E-mail: kurpiews@chemia.uj.edu.pl [Jagiellonian University, Faculty of Chemistry, Department of Crystal Chemistry and Crystal Physics, Protein Crystallography Group, Ingardena 3, 30-060 Kraków (Poland); Dziubek, Kamil; Katrusiak, Andrzej [Adam Mickiewicz University, Faculty of Chemistry, Department of Materials Chemistry, Umultowska 89b, 61-61 Poznań (Poland); Font, Josep [School of Medical Science, University of Sydney, NSW 2006 (Australia); Ribò, Marc; Vilanova, Maria [Universitat de Girona, Laboratorid’Enginyeria de Proteïnes, Departament de Biologia, Facultat de Ciències, Campus de Montilivi, 17071 Girona (Spain); Lewiński, Krzysztof [Jagiellonian University, Faculty of Chemistry, Department of Crystal Chemistry and Crystal Physics, Protein Crystallography Group, Ingardena 3, 30-060 Kraków (Poland)

    2016-04-01

    Highlights: • A unique crystallographic studies of wild-type and mutated form of the same protein under high pressure. • Compressibility of RNase A molecule is significantly affected by a single amino acid substitution. • High pressure protein crystallography helps understanding protein flexibility and identify conformational substrates. - Abstract: Hydrostatic pressure in range 0.1–1.5 GPa is used to modify biological system behaviour mostly in biophysical studies of proteins in solution. Due to specific influence on the system equilibrium high pressure can act as a filter that enables to identify and investigate higher energy protein conformers. The idea of the presented experiments is to examine the behaviour of RNase A molecule under high pressure before and after introduction of destabilizing mutation. For the first time crystal structures of wild-type bovine pancreatic ribonuclease A and its markedly less stable variant modified at position Ile106 were determined at different pressures. X-ray diffraction experiments at high pressure showed that the secondary structure of RNase A is well preserved even beyond 0.67 GPa at room temperature. Detailed structural analysis of ribonuclease A conformation observed under high pressure revealed that pressure influences hydrogen bonds pattern, cavity size and packing of molecule.

  2. The nuclear physical method for high pressure steam manifold water level gauging and its error

    International Nuclear Information System (INIS)

    Li Nianzu; Li Beicheng; Jia Shengming

    1993-10-01

    A new method, which is non-contact on measured water level, for measuring high pressure steam manifold water level with nuclear detection technique is introduced. This method overcomes the inherent drawback of previous water level gauges based on other principles. This method can realize full range real time monitoring on the continuous water level of high pressure steam manifold from the start to full load of boiler, and the actual value of water level can be obtained. The measuring errors were analysed on site. Errors from practical operation in Tianjin Junliangcheng Power Plant and in laboratory are also presented

  3. High pressure oxidation of C2H4/NO mixtures

    DEFF Research Database (Denmark)

    Giménez-López, J.; Alzueta, M.U.; Rasmussen, C.T.

    2011-01-01

    An experimental and kinetic modeling study of the interaction between C2H4 and NO has been performed under flow reactor conditions in the intermediate temperature range (600–900K), high pressure (60bar), and for stoichiometries ranging from reducing to oxidizing conditions. The main reaction...... pathways of the C2H4/O2/NOx conversion, the capacity of C2H4 to remove NO, and the influence of the presence of NOx on the C2H4 oxidation are analyzed. Compared to the C2H4/O2 system, the presence of NOx shifts the onset of reaction 75–150K to lower temperatures. The mechanism of sensitization involves...

  4. High pressure as an alternative processing step for ham production.

    Science.gov (United States)

    Pingen, Sylvia; Sudhaus, Nadine; Becker, André; Krischek, Carsten; Klein, Günter

    2016-08-01

    As high pressure processing (HPP) is becoming more and more important in the food industry, this study examined the application of HPP (500 and 600MPa) as a manufacturing step during simulated ham production. By replacing conventional heating with HPP steps, ham-like texture or color attributes could not be achieved. HPP products showed a less pale, less red appearance, softer texture and higher yields. However, a combination of mild temperature (53°C) and 500MPa resulted in parameters more comparable to cooked ham. We conclude that HPP can be used for novel food development, providing novel textures and colors. However, when it comes to ham production, a heating step seems to be unavoidable to obtain characteristic ham properties. Copyright © 2016 Elsevier Ltd. All rights reserved.

  5. High-pressure Raman spectroscopy of phase change materials

    Energy Technology Data Exchange (ETDEWEB)

    Hsieh, Wen-Pin, E-mail: wphsieh@stanford.edu; Mao, Wendy L. [SLAC National Accelerator Laboratory, Stanford Institute for Materials and Energy Sciences, Menlo Park, California 94025 (United States); Department of Geological and Environmental Sciences, Stanford University, Stanford, California 94305 (United States); Zalden, Peter [SLAC National Accelerator Laboratory, Stanford Institute for Materials and Energy Sciences, Menlo Park, California 94025 (United States); Wuttig, Matthias [I. Physikalisches Institut (IA), RWTH Aachen University, 52056 Aachen (Germany); JARA – Fundamentals of Future Information Technology, RWTH Aachen University, 52056 Aachen (Germany); Lindenberg, Aaron M. [SLAC National Accelerator Laboratory, Stanford Institute for Materials and Energy Sciences, Menlo Park, California 94025 (United States); Department of Materials Science and Engineering, Stanford University, Stanford, California 94305 (United States); SLAC National Accelerator Laboratory, PULSE Institute, Menlo Park, California 94025 (United States)

    2013-11-04

    We used high-pressure Raman spectroscopy to study the evolution of vibrational frequencies of the phase change materials (PCMs) Ge{sub 2}Sb{sub 2}Te{sub 5}, GeSb{sub 2}Te{sub 4}, and SnSb{sub 2}Te{sub 4}. We found that the critical pressure for triggering amorphization in the PCMs decreases with increasing vacancy concentration, demonstrating that the presence of vacancies, rather than differences in the atomic covalent radii, is crucial for pressure-induced amorphization in PCMs. Compared to the as-deposited amorphous phase, the pressure-induced amorphous phase has a similar vibrational spectrum but requires much lower laser power to transform into the crystalline phase, suggesting different kinetics of crystallization, which may have implications for applications of PCMs in non-volatile data storage.

  6. Synthesis and properties of selenium trihydride at high pressures

    Science.gov (United States)

    Zhang, Xiao; Xu, Wan; Wang, Yu; Jiang, Shuqing; Gorelli, Federico A.; Greenberg, Eran; Prakapenka, Vitali B.; Goncharov, Alexander F.

    2018-02-01

    The chemical reaction products of molecular hydrogen (H2) with selenium (Se) are studied by synchrotron x-ray diffraction (XRD) and Raman spectroscopy at high pressures. We find that a common H2Se is synthesized at 0.3 GPa using laser heating. Upon compression at 300 K, a crystal of the theoretically predicted Cccm H3Se has been grown at 4.6 GPa. At room temperature, H3Se shows a reversible phase decomposition after laser irradiation above 8.6 GPa, but remains stable up to 21 GPa. However, at 170 K Cccm H3Se persists up to 39.5 GPa based on XRD measurements, while low-temperature Raman spectra weaken and broaden above 23.1 GPa. At these conditions, the sample is visually nontransparent and shiny suggesting that metallization occurred.

  7. Rancidity inhibition study in frozen whole mackerel (scomber scombrus by a previous plant extract treatment.

    Directory of Open Access Journals (Sweden)

    Aubourg, Santiago P.

    2005-09-01

    Full Text Available The effect of flaxseeds (Linum usitatissimum on rancidity development in frozen whole mackerel (Scomber scombrus was studied. For it, fresh mackerel were dipped in flaxseeds aqueous extract during 60 min, frozen at –80 ºC during 24 hours and kept frozen (–20 ºC up to 12 months. Sampling was carried out on the initial material and at months 1, 3, 5, 7, 9 and 12 of frozen storage at –20 ºC. A parallel experiment with non treated fish was carried out in the same conditions. Rancidity development was measured by several biochemical indices (free fatty acids, peroxides, conjugated dienes and trienes, secondary oxidation products and lipoxygenase activity and complemented by the sensory analysis (skin, flesh odour, consistency and flesh appearance. As a result of the previous antioxidant treatment, peroxides showed to breakdown faster (pSe ha estudiado el efecto del lino (Linum usitatissimum en el desarrollo de rancidez en caballa entera congelada (Scomber scombrus. Para ello, caballas frescas fueron sumergidas en extractos acuosos de semillas de lino durante 60 min, congeladas a -80 ºC durante 24 h y mantenidas congeladas ( -20 ºC durante 12 meses. Se tomaron muestras del material inicial y tras 1, 3, 5, 7, 9 y 12 meses de congelación a -20 ºC . Un experimento paralelo con pescado no tratado fue llevado acabo en las mismas condiciones. El desarrollo de la rancidez fue medido por varios índices bioquímicos (ácidos grasos libres, peróxidos, dienos y trienos conjugados, productos secundarios de oxidación y actividad lipoxigenasa y completado con análisis sensorial (piel, olor de la carne, consistencia y apariencia de la carne. Como resultado del tratamiento antioxidante, los peróxidos se degradaron más rápidos (p < 0.05 después del mes 7, y por tanto, contenidos mayores (p < 0.05 de dienos y trienos conjugados pudieron ser detectados en el pescado tratado. El tratamiento antioxidante también condujo a un

  8. Automated high pressure cell for pressure jump x-ray diffraction

    International Nuclear Information System (INIS)

    Brooks, Nicholas J.; Gauthe, Beatrice L. L. E.; Templer, Richard H.; Ces, Oscar; Seddon, John M.; Terrill, Nick J.; Rogers, Sarah E.

    2010-01-01

    A high pressure cell for small and wide-angle x-ray diffraction measurements of soft condensed matter samples has been developed, incorporating a fully automated pressure generating network. The system allows both static and pressure jump measurements in the range of 0.1-500 MPa. Pressure jumps can be performed as quickly as 5 ms, both with increasing and decreasing pressures. Pressure is generated by a motorized high pressure pump, and the system is controlled remotely via a graphical user interface to allow operation by a broad user base, many of whom may have little previous experience of high pressure technology. Samples are loaded through a dedicated port allowing the x-ray windows to remain in place throughout an experiment; this facilitates accurate subtraction of background scattering. The system has been designed specifically for use at beamline I22 at the Diamond Light Source, United Kingdom, and has been fully integrated with the I22 beamline control systems.

  9. Automated high pressure cell for pressure jump x-ray diffraction.

    Science.gov (United States)

    Brooks, Nicholas J; Gauthe, Beatrice L L E; Terrill, Nick J; Rogers, Sarah E; Templer, Richard H; Ces, Oscar; Seddon, John M

    2010-06-01

    A high pressure cell for small and wide-angle x-ray diffraction measurements of soft condensed matter samples has been developed, incorporating a fully automated pressure generating network. The system allows both static and pressure jump measurements in the range of 0.1-500 MPa. Pressure jumps can be performed as quickly as 5 ms, both with increasing and decreasing pressures. Pressure is generated by a motorized high pressure pump, and the system is controlled remotely via a graphical user interface to allow operation by a broad user base, many of whom may have little previous experience of high pressure technology. Samples are loaded through a dedicated port allowing the x-ray windows to remain in place throughout an experiment; this facilitates accurate subtraction of background scattering. The system has been designed specifically for use at beamline I22 at the Diamond Light Source, United Kingdom, and has been fully integrated with the I22 beamline control systems.

  10. Ultrasonic depth gauge for liquids under high pressure

    Science.gov (United States)

    Zuckerwar, Allan J. (Inventor); Mazel, David S. (Inventor)

    1988-01-01

    The invention relates to an ultrasonic depth gauge for liquids under high pressure and is particularly useful in the space industry where it is necessary to use a pressurized gas to transfer a liquid from one location to another. Conventional liquid depth gauges do not have the capability to operate under extreme high pressure (i.e., exceeding 300 psi). An ultrasonic depth gauge capable of withstanding high pressure according to the present invention is comprised of a transducer assembly and a supporting electronics unit. The former is mounted in to the bottom wall of a storage vessel with its resonating surface directly exposed to the highly pressurized liquid in the vessel. In operation, the ultrasonic pulse propagates upward through the liquid to the liquid-gas interface in the storage vessel. When the ultrasonic echo returns from the liquid-gas interface, it re-excites the composite resonator into vibration. The supporting electronics unit measures the round-trip transmit time for the ultrasonic pulse and its return echo to traverse the depth of the highly pressurized liquid. The novelty of the invention resides in the use of a conventional transducer rigidly bonded to the inside wall of a bored out conventional high-pressure plug to form a composite resonator capable of withstanding extremely high pressure.

  11. Effect of Previous Irradiation on Vascular Thrombosis of Microsurgical Anastomosis: A Preclinical Study in Rats

    Science.gov (United States)

    Gallardo-Calero, Irene; López-Fernández, Alba; Romagosa, Cleofe; Vergés, Ramona; Aguirre-Canyadell, Marius; Soldado, Francisco; Velez, Roberto

    2016-01-01

    Background: The objective of the present investigation was to compare the effect of neoadjuvant irradiation on the microvascular anastomosis in cervical bundle using an experimental model in rats. Methods: One hundred forty male Sprague–Dawley rats were allocated into 4 groups: group I, control, arterial microanastomosis; group II, control, venous microanastomosis; group III, arterial microanastomosis with previous irradiation (20 Gy); and group IV, venous microanastomosis with previous irradiation (20 Gy). Clinical parameters, technical values of anastomosis, patency, and histopathological parameters were evaluated. Results: Irradiated groups (III and IV) and vein anastomosis groups (II and IV) showed significantly increased technical difficulties. Group IV showed significantly reduced patency rates (7/35) when compared with the control group (0/35). Radiotherapy significantly decreased the patency rates of the vein (7/35) when compared with the artery (1/35). Groups III and IV showed significantly reduced number of endothelial cells and also showed the presence of intimal thickening and adventitial fibrosis as compared with the control group. Conclusion: Neoadjuvant radiotherapy reduces the viability of the venous anastomosis in a preclinical rat model with a significant increase in the incidence of vein thrombosis. PMID:27975009

  12. Dynamic Strength of Metals at High Pressure and Strain Rate

    Science.gov (United States)

    Lorenz, Thomas

    2006-03-01

    A new approach to materials science at very high pressures and strain rates has been developed on the Omega laser, using a ramped plasma piston drive. A laser drives an ablative shock through a solid plastic reservoir where it unloads at the rear free surface, expands across a vacuum gap, and stagnates on the metal sample under study. This produces a gently increasing ram pressure, compressing the sample nearly isentropically. The peak pressure on the sample, diagnosed with VISAR measurements, can be varied by adjusting the laser energy and pulse length, gap size, and reservoir density, and obeys a simple scaling relation.^1 This has been demonstrated at OMEGA at pressures to 200 GPa in Al foils. In an important application, using in-flight x-ray radiography, the material strength of solid-state samples at high pressure can be inferred by measuring the reductions in the growth rates (stabilization) of Rayleigh-Taylor (RT) unstable interfaces. RT instability measurements of solid of Al-6061-T6 ^2 and vanadium, at pressures of 20-100 GPa, and strain rates of 10^6 to 10^8 s-1, show clear material strength effects. Modelling results for two constitutive strength models -- Steinberg-Guinan and Preston-Tonks-Wallace, show enhanced dynamic strength that may be correlated with a high-strain-rate, phono-drag mechanism. Data, modeling details and future prospects for this project using the National Ignition Facility laser, will be presented. [1] J. Edwards et al., Phys. Rev. Lett., 92, 075002 (2004). [2] K. T. Lorenz et al., Phys. Plasmas 12, 056309 (2005). This work was performed under the auspices of the U.S. Department of Energy by the University of California, Lawrence Livermore National Laboratory under Contract W-7405-Eng-48.

  13. High-pressure phase transitions of deep earth materials

    International Nuclear Information System (INIS)

    Hirose, Kei

    2009-01-01

    Recent developments in synchrotron XRD measurements combined with laser-heated diamond-anvil cell (LHDAC) techniques have enabled us to search for a novel phase transition at extremely high pressure and temperature. A phase transition from MgSiO 3 perovskite to post-perovskite was discovered through a drastic change in XRD patterns above 120 GPa and 2500 K, corresponding to the condition in the lowermost mantle (Murakami et al., 2004; Oganov and Ono, 2004). A pressure-induced phase transformation from ABO 3 -type perovskite to any denser structures was not known at that time. This new MgSiO 3 polymorph called post-perovskite has an orthorhombic symmetry (space group: Cmcm) with a sheet-stacking structure. The Mg site in post-perovskite is smaller than that in perovskite, which results in a volume reduction by 1.0-1.5% from perovskite structure. The electrical conductivity of post-perovskite is higher by three orders of magnitude than that of perovskite at similar pressure range (Ohta et al., 2008). This is likely due to a shorter Fe-Fe distance in post-perovskite structure, while conduction mechanism is yet to be further examined. Phase transition boundary between perovskite and post-perovskite has been determined in a wide temperature range up to 4400 K at 170 GPa (Tateno et al., 2008). Phase relations of Fe alloys have been also studied at core pressures (>135 GPa), although the generation of high temperature is more difficult at higher pressures. A new high-pressure B2 phase of B2 phase of FeS was recently discovered above 180 GPa (Sata et al., 2008). The Fe-Ni alloys have a wide pressure-temperature stability field of fcc phase at the core pressure range, depending on the Ni content (Kuwayama et al., 2008). (author)

  14. Safety analysis of high pressure gasous fuel container punctures

    Energy Technology Data Exchange (ETDEWEB)

    Swain, M.R. [Univ. of Miami, Coral Gables, FL (United States)

    1995-09-01

    The following report is divided into two sections. The first section describes the results of ignitability tests of high pressure hydrogen and natural gas leaks. The volume of ignitable gases formed by leaking hydrogen or natural gas were measured. Leaking high pressure hydrogen produced a cone of ignitable gases with 28{degrees} included angle. Leaking high pressure methane produced a cone of ignitable gases with 20{degrees} included angle. Ignition of hydrogen produced larger overpressures than did natural gas. The largest overpressures produced by hydrogen were the same as overpressures produced by inflating a 11 inch child`s balloon until it burst.

  15. Safety supervision on high-pressure gas regulations

    International Nuclear Information System (INIS)

    Lee, Won Il

    1991-01-01

    The first part lists the regulation on safety supervision of high-pressure gas, enforcement ordinance on high-pressure gas safety supervision and enforcement regulations about high-pressure gas safety supervision. The second part indicates safety regulations on liquefied petroleum gas and business, enforcement ordinance of safety on liquefied petroleum gas and business, enforcement regulation of safety supervision over liquefied petroleum gas and business. The third part lists regulation on gas business, enforcement ordinance and enforcement regulations on gas business. Each part has theory and explanation for questions.

  16. Recombination times in germanium under high pressure

    International Nuclear Information System (INIS)

    Kuyt, J.H.

    1975-01-01

    The influence of pressure on a well defined recombination process was studied. The centres were introduced by γirradiation and the lifetime determined by the decay time of photoconductivity. An optical pressure vessel is described which allows for a hydrostatic variation of 3000 bars. The diffusion constant and lifetime measurements are presented and analysed. (V.J.C.)

  17. Magnetic structures of erbium under high pressure

    DEFF Research Database (Denmark)

    Kawano, S.; Lebech, B.; Achiwa, N.

    1993-01-01

    Neutron diffraction studies of the magnetic structures of erbium metal at 4.5 K and 11.5 kbar hydrostatic pressure have revealed that the transition to a conical structure at low temperatures is suppressed and that the cycloidal structure, with modulation vector Q congruent-to (2/7 2pi/c)c persists...

  18. Radiation interactions in high-pressure gases

    International Nuclear Information System (INIS)

    Christophorou, L.G.

    1990-01-01

    This article is on basic radiation interaction processes in dense fluids and on interphase studies aiming at the interfacing of knowledge on radiation interaction processes in the gaseous and the liquid state of matter. It is specifically focused on the effect of the density and nature of the medium on electron production in irradiated fluids and on the state, energy, transport, and attachment of slow excess electrons in dense fluids especially dielectric liquids which possess excess-electron conduction bands (V 0 < 0 eV). Studies over the past two decades have shown that the interactions of low-energy electrons with molecules embedded in dense media depend not only on the molecules themselves and their internal state of excitation, but also on the electron state and energy in -- and the nature and density of -- the medium in which the interactions occur

  19. High-pressure X-ray study of LiCrSi2O6 clinopyroxene and the general compressibility trends of Li-clinopyroxenes

    DEFF Research Database (Denmark)

    Periotto, Benedetta; Angel, Ross J.; Nestola, Fabrizio

    2013-01-01

    High-pressure single-crystal X-ray diffraction measurements of synthetic LiCrSi2O6 clinopyroxene (with space group P21/c) were performed in a diamond-anvil cell up to 7.970 GPa. No phase transition has been observed within the pressure range investigated, but the elastic behavior at lower pressures...... (up to 2.5 GPa) is affected by an anomalous softening due to the proximity of the phase transition to the HT-C2/c phase at 330 K and at ambient pressure. A third-order Birch–Murnaghan equation of state fitted to the compression data above 2.5 GPa yields a bulk modulus KT0 = 93(2) GPa and its first...... derivative K0 = 8.8(6). The structural data measured up to 7.970 GPa confirm that the space group P21/c is maintained throughout the whole pressure range investigated. The atomic parameters, obtained from the integrated diffraction intensities, suggest that the Li coordination polyhedron changes its...

  20. The effect of chalcogen atom on the structural, elastic, and high-pressure properties of XY compounds (X = La, Ce, Eu, and Y = S, Se, and Te): An ab initio study

    Energy Technology Data Exchange (ETDEWEB)

    Charifi, Z.; Baaziz, H. [Physics Department, Faculty of Science, University of M' sila, 28000 M' sila (Algeria); Saeed, Y. [School of Complex Systems, FFWP-South Bohemia University, Nove Hrady 37333 (Czech Republic); Reshak, Ali Hussain [School of Complex Systems, FFWP-South Bohemia University, Nove Hrady 37333 (Czech Republic); School of Material Engineering, Malaysia University of Perlis, P.O. Box 77, d/a Pejabat Pos Besar, 01007 Kangar, Perlis (Malaysia); Soltani, F. [Physics Department, Faculty of Science, University of Batna, 05000 Batna (Algeria)

    2012-01-15

    The B1 (NaCl) and B2 (CsCl) structure of rare-earth monochalcogenides XY (X = La, Ce, Eu, and Y = S, Se, and Te) were investigated with the full-potential linearized-augmented plane wave (FP-LAPW) scheme in the frame of the generalized gradient approximation (GGA). The optimized lattice parameters, independent elastic constants (C{sub 11}, C{sub 12}, and C{sub 44}) at zero and high pressure, bulk modulus B, and its pressure derivative and the shear modulus G were evaluated. Further, the numerical estimates of a set of elastic parameters [Young's modulus E, Poisson's ratio ({nu}), Lame's coefficients ({mu}, {lambda})] of the polycrystalline XY (X = La, Ce, Eu, and Y = S, Se, and Te) compounds (in the framework of the Voigt-Reuss-Hill approximation) were performed. The pressures at which these compounds undergo structural phase transition from B1 (NaCl) to B2 (CsCl) phases were calculated. For rare-earth monochalcogenides XY, the Debye temperature is also estimated from the average sound velocity. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)