Effect of Contact Pressure on the Resistance Contact Value and Temperature Changes in Copper Busbar Connection

Directory of Open Access Journals (Sweden)

Agus Risdiyanto

2012-12-01

Full Text Available This paper discussed the influence of tightness or contacts pressure on copper busbar joints to determine changes in the value of the initial contact resistance and the maximum temperature at the joint due to high current load. The test sample was copper busbar 3 x 30 mm with configuration of bolted overlapping joint. Increasing contact pressure at the joint was measured to find out its effect on the value of contact resistance. The applied pressure was 6 to 36 MPa. Procedure of contact resistance measurement refer to the ASTM B539 standard using four-wire method. The sample subsequently loaded with the current of 350 A for 60 minutes and the maximum temperature at the joint was measured. The result showed that increasing contact pressure at the busbar joint will reduce the contact resistance and maximum temperature. The increase of contact pressure from 6 to 30 MPa causes decreasing contact resistance from 16 μΩ to 11 μΩ. Further increasing of contact pressure more than 30 MPa did not affect the contact resistance significantly. The lowest temperatur of busbar joint of 54°C was reached at a contact pressure of 36 Mpa.

Use of ambulatory blood pressure measurement in the definition of resistant hypertension: a review of the evidence.

Science.gov (United States)

Persu, Alexandre; O'Brien, Eoin; Verdecchia, Paolo

2014-11-01

Resistant hypertension as defined by the European Society of Hypertension and American Heart Association is a blood pressure that remains uncontrolled despite concomitant intake of at least three antihypertensive drugs (one of them preferably being a diuretic) at full doses. This definition is still based on office rather than out-of-office blood pressure measurement. In this review we propose a new, stricter definition of resistant hypertension based on ambulatory blood pressure measurement. The main arguments in favor of this are: (1) in patients with resistant hypertension, ambulatory blood pressure is an independent predictor of cardiovascular morbidity whereas, after adjustment for conventional risk factors, conventional blood pressure has little added value; (2) white-coat resistant hypertension (uncontrolled office with normal ambulatory blood pressure) is frequent (30-40% of patients with apparently resistant hypertension) carrying a prognosis similar to that of controlled hypertension, and intensification of blood pressure lowering treatment, or the use of nondrug treatment strategies such as renal denervation or carotid baroreceptor stimulation, is not justified; (3) masked resistant hypertension (controlled office with elevated ambulatory blood pressure) is frequent (approximately one-third of patients with controlled office blood pressure on triple antihypertensive therapy) and associated with an increased risk of cardiovascular events; in such patients, treatment intensification should be considered; (4) the current definition of resistant hypertension (office blood pressure ⩾ 140/90 mm Hg on triple antihypertensive therapy) allows a substantial proportion of patients with spurious or white-coat resistant hypertension to undergo renal denervation in the absence of proven long-term benefits.

Design of a pressurized water loop heated by electric resistances

International Nuclear Information System (INIS)

Ribeiro, S.V.G.

1981-01-01

A pressurized water loop design is presented. Its operating pressure is 420 psi and we seek to simulate qualitatively some thermo-hydraulic phenomena of PWR reactors. The primary circuit simulator consists basically of two elements: 1)the test section housing 16 electric resistences dissipating a total power of 100 Kw; 2)the loop built of SCH40S 304L steel piping, consisting of the pump, a heat exchanger and the pressurizer. (Author) [pt

High hydrostatic pressure resistance of Campylobacter jejuni after different sublethal stresses.

Science.gov (United States)

Sagarzazu, N; Cebrián, G; Condón, S; Mackey, B; Mañas, P

2010-07-01

To study the development of resistance responses in Campylobacter jejuni to high hydrostatic pressure (HHP) treatments after the exposure to different stressful conditions that may be encountered in food-processing environments, such as acid pH, elevated temperatures and cold storage. Campylobacter jejuni cells in exponential and stationary growth phase were exposed to different sublethal stresses (acid, heat and cold shocks) prior to evaluate the development of resistance responses to HHP. For exponential-phase cells, neither of the conditions tested increased nor decreased HHP resistance of C. jejuni. For stationary-phase cells, acid and heat adaptation-sensitized C. jejuni cells to the subsequent pressure treatment. On the contrary, cold-adapted stationary-phase cells developed resistance to HHP. Whereas C. jejuni can be classified as a stress sensitive micro-organism, our findings have demonstrated that it can develop resistance responses under different stressing conditions. The resistance of stationary phase C. jejuni to HHP was increased after cells were exposed to cold temperatures. The results of this study contribute to a better knowledge of the physiology of C. jejuni and its survival to food preservation agents. Results here presented may help in the design of combined processes for food preservation based on HHP technology. © 2009 The Authors. Journal compilation © 2009 The Society for Applied Microbiology.

Variation in Resistance of Natural Isolates of Escherichia coli O157 to High Hydrostatic Pressure, Mild Heat, and Other Stresses

OpenAIRE

Benito, Amparo; Ventoura, Georgia; Casadei, Maria; Robinson, Tobin; Mackey, Bernard

1999-01-01

Strains of Escherichia coli O157 isolated from patients with clinical cases of food-borne illness and other sources exhibited wide differences in resistance to high hydrostatic pressure. The most pressure-resistant strains were also more resistant to mild heat than other strains. Strain C9490, a representative pressure-resistant strain, was also more resistant to acid, oxidative, and osmotic stresses than the pressure-sensitive strain NCTC 12079. Most of these differences in resistance were o...

Study on the Mould-Resistant Properties of Moso Bamboo Treated with High Pressure and Amylase

Directory of Open Access Journals (Sweden)

Xiao-Dong Huang

2013-11-01

Full Text Available Starch of moso bamboo mainly exists in the elongated parenchyma cells, and it is difficult for amylase to enter moso bamboo and dissolve the starch. Therefore, the mould resistance capability of moso bamboo’s products cannot meet the need for bamboo to resist fungal decay. In this experiment, moso bamboo blocks were first treated at six levels of pressure and for six different treatment durations. The results showed that reducing sugar content was decreased dramatically from 0.92 mg/L to 0.19 mg/L and the starch content decreased from 1.18% to 0.96% when the pressure was increased from 0 psi to 100 psi. Regression analysis showed that the effects of an individual amylase reaction and individual pressure treatment on the starch or reducing sugar content were significant with a high correlation coefficient. Three traditional types of moso bamboo moulds (Aspergillus niger, Penicillium citrinum, and Trichoderma viride were then used for mould resistance testing. The results revealed that the mould resistance capability of moso bamboo blocks could be greatly improved by the combined effect of enzyme activity and pressure treatment. Mould resistance was enhanced by increasing the pressure or prolonging the treatment time. This research could provide a new method for the protection of bamboo from mould attack.

Pressure-induced positive electrical resistivity coefficient in Ni-Nb-Zr-H glassy alloy

Science.gov (United States)

Fukuhara, M.; Gangli, C.; Matsubayashi, K.; Uwatoko, Y.

2012-06-01

Measurements under hydrostatic pressure of the electrical resistivity of (Ni0.36Nb0.24Zr0.40)100-xHx (x = 9.8, 11.5, and 14) glassy alloys have been made in the range of 0-8 GPa and 0.5-300 K. The resistivity of the (Ni0.36Nb0.24Zr0.40)86H14 alloy changed its sign from negative to positive under application of 2-8 GPa in the temperature range of 300-22 K, coming from electron-phonon interaction in the cluster structure under pressure, accompanied by deformation of the clusters. In temperature region below 22 K, the resistivity showed negative thermal coefficient resistance by Debye-Waller factor contribution, and superconductivity was observed at 1.5 K.

Variation in Resistance of Natural Isolates of Escherichia coli O157 to High Hydrostatic Pressure, Mild Heat, and Other Stresses

Science.gov (United States)

Benito, Amparo; Ventoura, Georgia; Casadei, Maria; Robinson, Tobin; Mackey, Bernard

1999-01-01

Strains of Escherichia coli O157 isolated from patients with clinical cases of food-borne illness and other sources exhibited wide differences in resistance to high hydrostatic pressure. The most pressure-resistant strains were also more resistant to mild heat than other strains. Strain C9490, a representative pressure-resistant strain, was also more resistant to acid, oxidative, and osmotic stresses than the pressure-sensitive strain NCTC 12079. Most of these differences in resistance were observed only in stationary-phase cells, the only exception being acid resistance, where differences were also apparent in the exponential phase. Membrane damage in pressure-treated cells was revealed by increased uptake of the fluorescent dyes ethidium bromide and propidium iodide. When strains were exposed to the same pressure for different lengths of time, the pressure-sensitive strains took up stain sooner than the more resistant strain, which suggested that the differences in resistance may be related to susceptibility to membrane damage. Our results emphasize the importance of including stress-resistant strains of E. coli O157 when the efficacy of a novel or mild food preservation treatment is tested. PMID:10103251

Resistance exercise performed with repetitions until failure affects nocturnal blood pressure decreases in hypertensive women

Directory of Open Access Journals (Sweden)

Marilia de Almeida Correia

2015-12-01

Full Text Available Studies have shown that resistance exercise reduces 24-hour blood pressure to levels below resting values, although this is not a universal finding. The number of repetitions has been shown to influence this response. Thus, the aim of the study was to analyze the effects of resistance exercise performed until failure (UF on 24-hour blood pressure in hypertensive women. Thirteen hypertensive women underwent three experimental sessions in random order: UF, resistance exercise with repetitions before concentric failure (BF and control (C. Prior to and up to 24 hours after the sessions, cardiovascular variables, as well as the nocturnal fall in blood pressure, the morning surge, and the presence or absence of a blood pressure dip pattern were established using an ambulatory blood pressure monitor. In both wakefulness and sleep there was no significant difference among the three groups. However, after UF and C fewer patients presented a dip in blood pressure (46% and 38%, respectively compared BF (77%, p=0.047. In conclusion, the UF attenuated blood pressure dips at night in hypertensive patients.

Exercise is good for your blood pressure: effects of endurance training and resistance training.

Science.gov (United States)

Fagard, R H

2006-09-01

1. Although several epidemiological studies have not observed significant independent relationships between physical activity or fitness and blood pressure, others have concluded that blood pressure is lower in individuals who are more fit or active. However, longitudinal intervention studies are more appropriate for assessing the effects of physical activity on blood pressure. 2. Previously, we have performed meta-analyses of randomized controlled trials involving dynamic aerobic endurance training or resistance training. Inclusion criteria were: random allocation to intervention and control; physical training as the sole intervention; inclusion of healthy sedentary normotensive and/or hypertensive adults; intervention duration of at least 4 weeks; availability of systolic and/or diastolic blood pressure; and publication in a peer-reviewed journal up to December 2003. 3. The meta-analysis on endurance training involved 72 trials and 105 study groups. After weighting for the number of trained participants, training induced significant net reductions of resting and day time ambulatory blood pressure of 3.0/2.4 mmHg (P hypertensive study groups (-6.9/-4.9) than in the others (-1.9/-1.6; P training has been less well studied. A meta-analysis of nine randomized controlled trials (12 study groups) on mostly dynamic resistance training revealed a weighted net reduction of diastolic blood pressure of 3.5 mmHg (P endurance training decreases blood pressure through a reduction of systemic vascular resistance, in which the sympathetic nervous system and the renin-angiotensin system appear to be involved, and favourably affects concomitant cardiovascular risk factors. In addition, the few available data suggest that resistance training is able to reduce blood pressure.

[Resistance to peer and partner pressure and tobacco and alcohol use among adolescents].

Science.gov (United States)

Andrade Palos, Patricia; Pérez de la Barrera, Citlalli; Alfaro Martínez, Lilia Bertha; Sánchez Oviedo, Martha Elba; López Montes de Oca, Alicia

2009-01-01

Drug consumption constitutes a public health problem in Mexico. In the international literature and from the health promotion perspective, the Life Skills Approach proposed by the World Health Organization identifies the ability to resist pressure as a key component in the prevention of legal and illegal drug use among adolescents. An instrument for measuring this ability was developed and validated in order to confirm whether, as the empirical evidence suggests, it differs between users and non-users of alcohol and tobacco. The sample was made up of 5651 adolescents, 2637 (47.9%) of whom were male and 2864 (52.1%) female. These participants were selected at random from among public high school pupils in Mexico City, and average age was 16.7 years. The instrument used was that validated in the first phase of the study. To measure patterns of use, we used a scale based on indicators derived from the National Addiction Survey (2002). Factor analysis yielded three factors: peer pressure acceptance, partner pressure acceptance and peer/partner pressure resistance. Non-users of alcohol and tobacco scored higher in the ability to resist pressure than those who had used alcohol and tobacco in the last month. Based on these results, the aim is to develop an addiction prevention program for public high school pupils in Mexico City.

Body Size Predicts Cardiac and Vascular Resistance Effects on Men's and Women's Blood Pressure

Directory of Open Access Journals (Sweden)

Joyce M. Evans

2017-08-01

Full Text Available Key Points SummaryWe report how blood pressure, cardiac output and vascular resistance are related to height, weight, body surface area (BSA, and body mass index (BMI in healthy young adults at supine rest and standing.Much inter-subject variability in young adult's blood pressure, currently attributed to health status, may actually result from inter-individual body size differences.Each cardiovascular variable is linearly related to height, weight and/or BSA (more than to BMI.When supine, cardiac output is positively related, while vascular resistance is negatively related, to body size. Upon standing, the change in vascular resistance is positively related to size.The height/weight relationships of cardiac output and vascular resistance to body size are responsible for blood pressure relationships to body size.These basic components of blood pressure could help distinguish normal from abnormal blood pressures in young adults by providing a more effective scaling mechanism.Introduction: Effects of body size on inter-subject blood pressure (BP variability are not well established in adults. We hypothesized that relationships linking stroke volume (SV, cardiac output (CO, and total peripheral resistance (TPR with body size would account for a significant fraction of inter-subject BP variability.Methods: Thirty-four young, healthy adults (19 men, 15 women participated in 38 stand tests during which brachial artery BP, heart rate, SV, CO, TPR, and indexes of body size were measured/calculated.Results: Steady state diastolic arterial BP was not significantly correlated with any index of body size when subjects were supine. However, upon standing, the more the subject weighed, or the taller s/he was, the greater the increase in diastolic pressure. Systolic pressure strongly correlated with body weight and height both supine and standing. Diastolic and systolic BP were more strongly related to height, weight and body surface area than to body mass

High precision silicon piezo resistive SMART pressure sensor

International Nuclear Information System (INIS)

Brown, Rod

2005-01-01

Instruments for test and calibration require a pressure sensor that is precise and stable. Market forces also dictate a move away from single measurand test equipment and, certainly in the case of pressure, away from single range equipment. A pressure 'module' is required which excels in pressure measurement but is interchangble with sensors for other measurands. A communications interface for such a sensor has been specified. Instrument Digital Output Sensor (IDOS) that permits this interchanagability and allows the sensor to be inside or outside the measuring instrument. This paper covers the design and specification of a silicon diaphragm piezo resistive SMART sensor using this interface. A brief history of instrument sensors will be given to establish the background to this development. Design choices of the silicon doping, bridge energisation method, temperature sensing, signal conversion, data processing, compensation method, communications interface will be discussed. The physical format of the 'in-instrument' version will be shown and then extended to the packaging design for the external version. Test results will show the accuracy achieved exceeds the target of 0.01%FS over a range of temperatures

High precision silicon piezo resistive SMART pressure sensor

Science.gov (United States)

Brown, Rod

2005-01-01

Instruments for test and calibration require a pressure sensor that is precise and stable. Market forces also dictate a move away from single measurand test equipment and, certainly in the case of pressure, away from single range equipment. A pressure `module' is required which excels in pressure measurement but is interchangble with sensors for other measurands. A communications interface for such a sensor has been specified. Instrument Digital Output Sensor (IDOS) that permits this interchanagability and allows the sensor to be inside or outside the measuring instrument. This paper covers the design and specification of a silicon diaphragm piezo resistive SMART sensor using this interface. A brief history of instrument sensors will be given to establish the background to this development. Design choices of the silicon doping, bridge energisation method, temperature sensing, signal conversion, data processing, compensation method, communications interface will be discussed. The physical format of the `in-instrument' version will be shown and then extended to the packaging design for the external version. Test results will show the accuracy achieved exceeds the target of 0.01%FS over a range of temperatures.

Acute effect of resistance, aerobic and combined exercise circuits on blood pressure of hypertensive women

Directory of Open Access Journals (Sweden)

Elizabeth Carpio Rivera

2012-11-01

Full Text Available Carpio-Rivera, E. y Solera-Herrera, A. (2012. Acute effect of resistance, aerobic and combined exercise circuits on blood pressure of hypertensive women. Pensar en Movimiento: Revista de Ciencias del Ejercicio y la Salud, 10 (2, 1-12. The purpose of this study was to observe the acute effect of different exercises executed in circuit on the resting blood pressure of hypertensive women. Nine trained persons (aged 53.22 ± 4.67 years, hypertensive but medicated with enalapril, participated in four training treatments, each carried out on different days under a randomized repeated measures design: (1 A: aerobic training condition (steps training; (2 R: resistance training condition (machine training (3 AR: aerobic and resistance training condition (alternating aerobic and resistance training every 30 seconds (4 C: control condition (30 minutes resting. Exercise conditions were performed during 30 minutes at 70% of maximum heart rate and resting blood pressure was measured 5 minutes before and immediately after each condition. A two-way analysis of variance detected a significant interaction between conditions and measurements (p<0.05 on systolic blood pressure (sBP. Tukey Post-hoc analyses showed a significant increase of sBP following the three exercise conditions (A: +19 mmHg; R: +28 mmHg; AR: +22 mmHg, while the sBP remained unchanged during the control condition. In contrast, there was no significant effect of any type of exercise on diastolic blood pressure (dBP. In conclusion, the acute elevation in sBP following this type of resistance exercise was similar to the increase produced by aerobic exercise.

Hydrostatic pressure (8 GPa) dependence of electrical resistivity of BaCo{sub 2}As{sub 2} single crystal

Energy Technology Data Exchange (ETDEWEB)

Ganguli, Chandreyee; Matsubayashi, Kazuyuki; Ohgushi, Kenya [Institute for Solid State Physics, The University of Tokyo, Kashiwanoha, Kashiwa, Chiba 277-8581 (Japan); Uwatoko, Yoshiya, E-mail: uwatoko@issp.u-tokyo.ac.jp [Institute for Solid State Physics, The University of Tokyo, Kashiwanoha, Kashiwa, Chiba 277-8581 (Japan); Kanagaraj, Moorthi [Centre for High Pressure Research, School of Physics, Bharathidasan University, Tiruchirappalli 620024 (India); Arumugam, Sonachalam, E-mail: sarumugam1963@yahoo.com [Centre for High Pressure Research, School of Physics, Bharathidasan University, Tiruchirappalli 620024 (India)

2013-10-15

Graphical abstract: - Highlights: • Single crystals of BaCo{sub 2}As{sub 2} were grown by CoAs self-flux method. • We have studied pressure effects (8 GPa) on dc electrical resistivity of BaCo{sub 2}As{sub 2}. • On applied external pressure BaCo{sub 2}As{sub 2} remains a metallic state up to 8 GPa. • Superconductivity is absent in BaCo{sub 2}As{sub 2} because of its proximity to ferromagnetism. - Abstract: The pressure dependence of the electrical resistivity of BaCo{sub 2}As{sub 2} single crystal as a function of temperature was measured at ambient and high pressures up to 8 GPa for the first time using cubic anvil high pressure cell. It is observed that at room temperature the resistivity monotonically decreases with increasing pressure and it remains in the metallic state even at an applied pressure of 8 GPa. From the temperature dependence of the resistivity measurements under pressure, we found that superconductivity is absent up to 8 GPa. The value of the electron's scattering factor (A) is found to be large at ambient pressure and it decreases with the application of pressure, indicating that the substantial electron correlation effect of BaCo{sub 2}As{sub 2} is reduced under pressure, revealing a dramatic change of density of states at the Fermi energy.

Experimental study on the influence of chemical sensitizer on pressure resistance in deep water of emulsion explosives

Science.gov (United States)

Liu, Lei; zhang, Zhihua; Wang, Ya; Qin, hao

2018-03-01

The study on the pressure resistance performance of emulsion explosives in deep water can provide theoretical basis for underwater blasting, deep-hole blasting and emulsion explosives development. The sensitizer is an important component of emulsion explosives. By using reusable experimental devices to simulate the charge environment in deep water, the influence of the content of chemical sensitizer on the deep-water pressure resistance performance of emulsion explosives was studied. The experimental results show that with the increasing of the content of chemical sensitizer, the deep-water pressure resistance performance of emulsion explosives gradually improves, and when the pressure is fairly large, the effect is particularly pronounced; in a certain range, with the increase of the content of chemical sensitizer, that emulsion explosives’ explosion performance also gradually improve, but when the content reaches a certain value, the explosion properties declined instead; under the same emulsion matrix condition, when the content of NANO2 is 0.2%, that the emulsion explosives has good resistance to water pressure and good explosion properties. The correctness of the results above was testified in model blasting.

A Randomized Trial Comparing Two Tongue-Pressure Resistance Training Protocols for Post-Stroke Dysphagia.

Science.gov (United States)

Steele, Catriona M; Bayley, Mark T; Peladeau-Pigeon, Melanie; Nagy, Ahmed; Namasivayam, Ashwini M; Stokely, Shauna L; Wolkin, Talia

2016-06-01

The objective of this study was to compare the outcomes of two tongue resistance training protocols. One protocol ("tongue-pressure profile training") emphasized the pressure-timing patterns that are typically seen in healthy swallows by focusing on gradual pressure release and saliva swallowing tasks. The second protocol ("tongue-pressure strength and accuracy training") emphasized strength and accuracy in tongue-palate pressure generation and did not include swallowing tasks. A prospective, randomized, parallel allocation trial was conducted. Of 26 participants who were screened for eligibility, 14 received up to 24 sessions of treatment. Outcome measures of posterior tongue strength, oral bolus control, penetration-aspiration and vallecular residue were made based on videofluoroscopy analysis by blinded raters. Complete data were available for 11 participants. Significant improvements were seen in tongue strength and post-swallow vallecular residue with thin liquids, regardless of treatment condition. Stage transition duration (a measure of the duration of the bolus presence in the pharynx prior to swallow initiation, which had been chosen to capture impairments in oral bolus control) showed no significant differences. Similarly, significant improvements were not seen in median scores on the penetration-aspiration scale. This trial suggests that tongue strength can be improved with resistance training for individuals with tongue weakness following stroke. We conclude that improved penetration-aspiration does not necessarily accompany improvements in tongue strength; however, tongue-pressure resistance training does appear to be effective for reducing thin liquid vallecular residue.

Electrical resistance and magnetoresistance of UCoAl under high pressure

Czech Academy of Sciences Publication Activity Database

Honda, F.; Oomi, G.; Andreev, Alexander V.; Sechovský, V.; Shiokawa, Y.

--, - (2002), s. 126-128 ISSN 0022-3131 R&D Projects: GA ČR GP202/01/D045 Institutional research plan: CEZ:AV0Z1010914 Keywords : UCoAl * non-Fermi liquid * itinerant metamagnetism * electrical resistance * high pressure Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.572, year: 2002

Effect of aquatic resistance training on blood pressure and physical function of postmenopausal women

Directory of Open Access Journals (Sweden)

Mina Sattar

2012-12-01

Full Text Available Normal 0 false false false EN-US X-NONE AR-SA MicrosoftInternetExplorer4    BACKGROUND: In postmenopausal women, the risk of having cardiac diseases, especially high blood pressure, is increased due to the decrease in secretion of estrogen. The goal of this study was to evaluate the effect of 8 weeks of aquatic resistance training on blood pressure and physical function of postmenopausal women.    METHODS: In this quasi-experimental study, 24 postmenopausal women (age: 53-60 years, BMI= 29.23 ± 5.27kg/m2  ( were randomly divided into experimental (n = 14 and control (n = 10 groups. Women in the experimental group participated in an aquatic exercise program for 8 weeks (3 sessions per week in the deep parts of the pool. Training included walking and running in water with water dumbbells weighing 250 grams. Before and after the exercise period, the body composition, blood pressure, dynamic balance, and flexibility of the subjects were measured.    RESULTS: According to the T-score, the average systolic blood pressure in the experimental group significantly decreased (9.29% (P = 0.001. Dynamic balance and flexibility, respectively, significantly increased by 22.02% and 24.4% (P < 0.01. No significant changes were observed in body fat and weight.    CONCLUSION: Due to the positive effect of aquatic resistance training on blood pressure, dynamic balance, and flexibility these exercises are recommended for postmenopausal women.   Keywords: Menopausal Women, Blood Pressure, Flexibility, Aquatic Resistance Training  

Resistance Exercise Restores Endothelial Function and Reduces Blood Pressure in Type 1 Diabetic Rats

Energy Technology Data Exchange (ETDEWEB)

Mota, Marcelo Mendonça; Silva, Tharciano Luiz Teixeira Braga da; Fontes, Milene Tavares; Barreto, André Sales; Araújo, João Eliakim dos Santos [Departamento de Fisiologia - Universidade Federal de Sergipe (UFS), São Cristóvão, SE (Brazil); Oliveira, Antônio Cesar Cabral de; Wichi, Rogério Brandão [Departamento de Educação Física - UFS, São Cristóvão, SE (Brazil); Santos, Márcio Roberto Viana, E-mail: marciorvsantos@bol.com.br [Departamento de Fisiologia - Universidade Federal de Sergipe (UFS), São Cristóvão, SE (Brazil)

2014-07-15

Resistance exercise effects on cardiovascular parameters are not consistent. The effects of resistance exercise on changes in blood glucose, blood pressure and vascular reactivity were evaluated in diabetic rats. Wistar rats were divided into three groups: control group (n = 8); sedentary diabetic (n = 8); and trained diabetic (n = 8). Resistance exercise was carried out in a squat device for rats and consisted of three sets of ten repetitions with an intensity of 50%, three times per week, for eight weeks. Changes in vascular reactivity were evaluated in superior mesenteric artery rings. A significant reduction in the maximum response of acetylcholine-induced relaxation was observed in the sedentary diabetic group (78.1 ± 2%) and an increase in the trained diabetic group (95 ± 3%) without changing potency. In the presence of NG-nitro-L-arginine methyl ester, the acetylcholine-induced relaxation was significantly reduced in the control and trained diabetic groups, but not in the sedentary diabetic group. Furthermore, a significant increase (p < 0.05) in mean arterial blood pressure was observed in the sedentary diabetic group (104.9 ± 5 to 126.7 ± 5 mmHg) as compared to that in the control group. However, the trained diabetic group showed a significant decrease (p < 0.05) in the mean arterial blood pressure levels (126.7 ± 5 to 105.1 ± 4 mmHg) as compared to the sedentary diabetic group. Resistance exercise could restore endothelial function and prevent an increase in arterial blood pressure in type 1 diabetic rats.

Resistance Exercise Restores Endothelial Function and Reduces Blood Pressure in Type 1 Diabetic Rats

Directory of Open Access Journals (Sweden)

Marcelo Mendonça Mota

2014-07-01

Full Text Available Background: Resistance exercise effects on cardiovascular parameters are not consistent. Objectives: The effects of resistance exercise on changes in blood glucose, blood pressure and vascular reactivity were evaluated in diabetic rats. Methods: Wistar rats were divided into three groups: control group (n = 8; sedentary diabetic (n = 8; and trained diabetic (n = 8. Resistance exercise was carried out in a squat device for rats and consisted of three sets of ten repetitions with an intensity of 50%, three times per week, for eight weeks. Changes in vascular reactivity were evaluated in superior mesenteric artery rings. Results: A significant reduction in the maximum response of acetylcholine-induced relaxation was observed in the sedentary diabetic group (78.1 ± 2% and an increase in the trained diabetic group (95 ± 3% without changing potency. In the presence of NG-nitro-L-arginine methyl ester, the acetylcholine-induced relaxation was significantly reduced in the control and trained diabetic groups, but not in the sedentary diabetic group. Furthermore, a significant increase (p < 0.05 in mean arterial blood pressure was observed in the sedentary diabetic group (104.9 ± 5 to 126.7 ± 5 mmHg as compared to that in the control group. However, the trained diabetic group showed a significant decrease (p < 0.05 in the mean arterial blood pressure levels (126.7 ± 5 to 105.1 ± 4 mmHg as compared to the sedentary diabetic group. Conclusions: Resistance exercise could restore endothelial function and prevent an increase in arterial blood pressure in type 1 diabetic rats.

Resistance Exercise Restores Endothelial Function and Reduces Blood Pressure in Type 1 Diabetic Rats

International Nuclear Information System (INIS)

Mota, Marcelo Mendonça; Silva, Tharciano Luiz Teixeira Braga da; Fontes, Milene Tavares; Barreto, André Sales; Araújo, João Eliakim dos Santos; Oliveira, Antônio Cesar Cabral de; Wichi, Rogério Brandão; Santos, Márcio Roberto Viana

2014-01-01

Resistance exercise effects on cardiovascular parameters are not consistent. The effects of resistance exercise on changes in blood glucose, blood pressure and vascular reactivity were evaluated in diabetic rats. Wistar rats were divided into three groups: control group (n = 8); sedentary diabetic (n = 8); and trained diabetic (n = 8). Resistance exercise was carried out in a squat device for rats and consisted of three sets of ten repetitions with an intensity of 50%, three times per week, for eight weeks. Changes in vascular reactivity were evaluated in superior mesenteric artery rings. A significant reduction in the maximum response of acetylcholine-induced relaxation was observed in the sedentary diabetic group (78.1 ± 2%) and an increase in the trained diabetic group (95 ± 3%) without changing potency. In the presence of NG-nitro-L-arginine methyl ester, the acetylcholine-induced relaxation was significantly reduced in the control and trained diabetic groups, but not in the sedentary diabetic group. Furthermore, a significant increase (p < 0.05) in mean arterial blood pressure was observed in the sedentary diabetic group (104.9 ± 5 to 126.7 ± 5 mmHg) as compared to that in the control group. However, the trained diabetic group showed a significant decrease (p < 0.05) in the mean arterial blood pressure levels (126.7 ± 5 to 105.1 ± 4 mmHg) as compared to the sedentary diabetic group. Resistance exercise could restore endothelial function and prevent an increase in arterial blood pressure in type 1 diabetic rats

Resistance calculation of un-fully developed two-phase flow through high differential pressure regulating valves

International Nuclear Information System (INIS)

Xu Mingyang; Wang Wenran; Wang Jiaying

1999-01-01

To reduce the flow velocity in the high differential pressure regulating valve with labyrinth. A type of complicated valve core structure were designed with tortuous flow path made from reversal double elbows. It is very difficult to calculate the pressure-drop of the un-fully developed two-phase flow under high temperature and pressure which flow through the valve core. A calculation method called 'constant (varing) pressure-drop progressing step by step design method' was developed. The complicated flow path was disintegrated into a series of independent resistance units and with the valve stem end progressing step by step the dimensions of the flow path were designed in accordance with the principle that in every position the total pressure-drop of the valve should amount to that required by the design goal curve. In the course of calculating the total pressure-drop, the valve flow path was also divided into a series of independent resistance units. The experiment results show that design flow characteristics are approximately consistent with the flow characteristics measured in the test

High-pressure resistivity measurements on the β-pyrochlore oxide KOs2O6

Science.gov (United States)

Ogusu, Hiroki; Takeshita, Nao; Yamaura, Jun-Ichi; Okamoto, Yoshihiko; Hiroi, Zenji

2010-12-01

High-pressure resistivity measurements are performed on a high-quality single crystal of the β-pyrochlore oxide KOs2O6 in the pressure range of 1.0 to 5.0 GPa. The superconducting transition temperature T increases slightly from 9.6 K at ambient pressure to 9.8 K at 1.0 GPa, decreases gradually with increasing pressure, and suddenly drops from 6.5 K to 3.2 K across P=3.6GPa. The drop of T at P is likely to be related to a change in the rattling vibration associated with a symmetry-breaking structural transition.

Variation in resistance of natural isolates of Staphylococcus aureus to heat, pulsed electric field and ultrasound under pressure.

Science.gov (United States)

Rodríguez-Calleja, J M; Cebrián, G; Condón, S; Mañas, P

2006-05-01

To study and compare the resistance of 15 Staphylococcus aureus isolates to heat, pulsed electric field (PEF) and ultrasound (UW) under pressure (manosonication, MS). Survival curves to heat (58 degrees C), to PEF (22 kV cm(-1), 2 micros square wave pulses) and to UW under pressure (117 microm, 20 kHz, 200 kPa) were obtained and inactivation parameters (decimal reduction times for heat and UW under pressure, and b-values for PEF) were calculated. A wide resistance variation to heat treatment, but not to PEF and MS, was observed amongst the 15 strains. There was no relationship between the resistances to the three physical agents studied. Staphylococcus aureus was relatively resistant to MS but sensitive to PEF. Heat resistance varied with strain and was positively correlated to carotenoid pigment content. Results would help in defining safe food preservation processes. Care should be taken to choose the most adequate strain of S. aureus to model food preservation processing.

Cochlear aqueduct flow resistance is not constant during evoked inner ear pressure change in the guinea pig

NARCIS (Netherlands)

Wit, HP; Feijen, RA; Albers, FWJ

Inner ear fluid pressure was measured during 6.25 mHz square wave middle ear pressure manipulation, with a perforated tympanic membrane. After a negative-going middle ear pressure change the calculated flow resistance of the inner ear pressure release routes (mainly the cochlear aqueduct) was

Laser and Pressure Resistance Weld of Thin-Wall Cladding for LWR Accident-Tolerant Fuels

Science.gov (United States)

Gan, J.; Jerred, N.; Perez, E.; Haggard, D. C.

2018-02-01

FeCrAl alloy with typical composition of approximately Fe-15Cr-5Al is considered a primary candidate cladding material for light water reactor accident-tolerant fuel because of its superior resistance to oxidation in high-temperature steam compared with Zircaloy cladding. Thin-walled FeCrAl cladding at 350 μm wall thickness is required, and techniques for joining endplug to cladding need to be developed. Fusion-based laser weld and solid-state joining with pressure resistance weld were investigated in this study. The results of microstructural characterization, mechanical property evaluation by tensile testing, and hydraulic pressure burst testing of the welds for the cladding-endplug specimen are discussed.

Improvement of methods to evaluate brittle failure resistance of the WWER reactor pressure vessels

Energy Technology Data Exchange (ETDEWEB)

Popov, A A; Parshutin, E V [Engineering Center of Nuclear Equipment Strength, Research and Development Inst. of Power Engineering, Moscow (Russian Federation); Rogov, M F; Dragunov, U G [Experimenter` s and Designer` s Office ` ` Hydropress` ` (Russian Federation)

1997-09-01

At the next 10 years a number of Russian WWER nuclear power plants will complete its design lifetime. Normative methods to evaluate brittle failure resistance of the reactor pressure vessels used in Russia have been intended for design stage. The evaluation of reactor pressure vessel lifetime in operation stage demands to create new methods of calculation and new methods for experimental evaluation of brittle failure resistance degradation. The main objective of the study in this type of reactor is weldment number 4. In this report an analysis is made of methods to determine critical temperature of reactor materials including the results of instrumented Charpy testing. 12 figs.

Robust zero resistance in a superconducting high-entropy alloy at pressures up to 190 GPa

Science.gov (United States)

Guo, Jing; Wang, Honghong; von Rohr, Fabian; Wang, Zhe; Cai, Shu; Zhou, Yazhou; Yang, Ke; Li, Aiguo; Jiang, Sheng; Wu, Qi; Cava, Robert J.; Sun, Liling

2017-12-01

We report the observation of extraordinarily robust zero-resistance superconductivity in the pressurized (TaNb)0.67(HfZrTi)0.33 high-entropy alloy--a material with a body-centered-cubic crystal structure made from five randomly distributed transition-metal elements. The transition to superconductivity (TC) increases from an initial temperature of 7.7 K at ambient pressure to 10 K at ˜60 GPa, and then slowly decreases to 9 K by 190.6 GPa, a pressure that falls within that of the outer core of the earth. We infer that the continuous existence of the zero-resistance superconductivity from 1 atm up to such a high pressure requires a special combination of electronic and mechanical characteristics. This high-entropy alloy superconductor thus may have a bright future for applications under extreme conditions, and also poses a challenge for understanding the underlying quantum physics.

Urinary albumin excretion is associated with nocturnal systolic blood pressure in resistant hypertensives.

Science.gov (United States)

Oliveras, Anna; Armario, Pedro; Martell-Clarós, Nieves; Ruilope, Luis M; de la Sierra, Alejandro

2011-03-01

Microalbuminuria is a known marker of subclinical organ damage. Its prevalence is higher in patients with resistant hypertension than in subjects with blood pressure at goal. On the other hand, some patients with apparently well-controlled hypertension still have microalbuminuria. The current study aimed to determine the relationship between microalbuminuria and both office and 24-hour ambulatory blood pressure. A cohort of 356 patients (mean age 64 ± 11 years; 40.2% females) with resistant hypertension (blood pressure ≥ 140 and/or 90 mm Hg despite treatment with ≥ 3 drugs, diuretic included) were selected from Spanish hypertension units. Patients with estimated glomerular filtration rate <30 mL/min/1.73 m(2) were excluded. All patients underwent clinical and demographic evaluation, complete laboratory analyses, and good technical-quality 24-hour ambulatory blood pressure monitoring. Urinary albumin/creatinine ratio was averaged from 3 first-morning void urine samples. Microalbuminuria (urinary albumin/creatinine ratio ≥ 2.5 mg/mmol in males or ≥ 3.5 mg/mmol in females) was detected in 46.6%, and impaired renal function (estimated glomerular filtration rate <60 mL/min/1.73 m(2)) was detected in 26.8%. Bivariate analyses showed significant associations of microalbuminuria with older age, reduced estimated glomerular filtration rate, increased nighttime systolic blood pressure, and elevated daytime, nighttime, and 24-hour diastolic blood pressure. In a logistic regression analysis, after age and sex adjustment, elevated nighttime systolic blood pressure (multivariate odds ratio, 1.014 [95% CI, 1.001 to 1.026]; P=0.029) and reduced estimated glomerular filtration rate (multivariate odds ratio, 2.79 [95% CI, 1.57 to 4.96]; P=0.0005) were independently associated with the presence of microalbuminuria. We conclude that microalbuminuria is better associated with increased nighttime systolic blood pressure than with any other office and 24-hour ambulatory blood

Sensitivity enhancement of polysilicon piezo-resistive pressure sensors with phosphorous diffused resistors

International Nuclear Information System (INIS)

Sivakumar, K; Dasgupta, N; Bhat, K N; Natarajan, K

2006-01-01

It is generally accepted that the piezo-resistive coefficient in single crystal silicon is higher when P-type impurities such as boron are used for doping the resistors. In this paper we demonstrate that the sensitivity of polycrystalline silicon piezo-resistive pressure sensors can be enhanced considerably when phosphorus diffusion source is used instead of boron dopant for realizing the piezo-resistors. Pressure sensors have been designed and fabricated with the polycrystalline piezo-resistors connected in the form of a Wheatstone bridge and laid out on thermal oxide grown on membranes obtained with a Silicon On Insulator (SOI) approach. The SOI wafers required for this purpose have been realized in-house by Silicon Fusion Bonding (SFB) and etch back technique in our laboratory. This approach provides excellent isolation between the resistors and enables zero temperature coefficient of the polysilicon resistor. The results obtained in our laboratory have clearly demonstrated that by optimizing the phosphorus diffusion temperature and duration, it is possible to achieve sensitivities in excess of 20mV /Bar for bridge input voltage of 10V, with linearity within 1% over a differential pressure range up to 10Bar (10 6 Pascal), and burst pressure in excess of 50 Bar as compared to the 10mV /Bar sensitivity obtained with boron doped polysilicon piezo-resistors. This enhancement is attributed to grain boundary passivation by phosphorous atoms

Resistance training alone reduces systolic and diastolic blood pressure in prehypertensive and hypertensive individuals: meta-analysis.

Science.gov (United States)

de Sousa, Evitom Corrêa; Abrahin, Odilon; Ferreira, Ana Lorena Lima; Rodrigues, Rejane Pequeno; Alves, Erik Artur Cortinhas; Vieira, Rodolfo Paula

2017-11-01

The purpose of this study was to evaluate the effects of resistance training alone on the systolic and diastolic blood pressure in prehypertensive and hypertensive individuals. Our meta-analysis, followed the guidelines of PRISMA. The search for articles was realized by November 2016 using the following electronic databases: BIREME, PubMed, Cochrane Library, LILACS and SciELO and a search strategy that included the combination of titles of medical affairs and terms of free text to the key concepts: 'hypertension' 'hypertensive', 'prehypertensive', 'resistance training', 'strength training', and 'weight-lifting'. These terms were combined with a search strategy to identify randomized controlled trials (RCTs) and identified a total of 1608 articles: 644 articles BIREME, 53 SciELO, 722 PubMed, 122 Cochrane Library and 67 LILACS. Of these, five RCTs met the inclusion criteria and provided data on 201 individuals. The results showed significant reductions for systolic blood pressure (-8.2 mm Hg CI -10.9 to -5.5;I 2 : 22.5% P valor for heterogeneity=0.271 and effect size=-0.97) and diastolic blood pressure (-4.1 mm Hg CI -6.3 to -1.9; I 2 : 46.5% P valor for heterogeneity=0.113 and effect size=-0.60) when compared to group control. In conclusion, resistance training alone reduces systolic and diastolic blood pressure in prehypertensive and hypertensive subjects. The RCTs studies that investigated the effects of resistance training alone in prehypertensive and hypertensive patients support the recommendation of resistance training as a tool for management of systemic hypertension.

Earthquake resistance of residual heat removed (RHR) pump for pressurized water reactors (PWR)

International Nuclear Information System (INIS)

Uga, Takeo; Shiraki, K.; Honma, T.; Matsubayashi, H.; Inazuka, H.

1980-01-01

The present paper deals with the earthquake resistance of the residual heat removed (RHR) pump of single stage double volute type, which is one of the structurally simplest pumps used for pressurized water reactors (PWR). The results of the study can be summarized as follows: (1) Any trouble which can give effect on the functions of the pump at earthquake does not become a problem so long as each part of the pump is of aseismatically rigid structure. (2) Aseismatic tolerance test in the pump's operating condition has shown that the earthquake resistance of the pump at its location has a tolerance about five times the dynamic design acceleration. (3) The pump is provided with an impeller-casing wear ring at the pressure boundary between the suction side pressure and discharge side pressure. This wear ring acts as an underwater bearing when the pump is in operation, and improves the vibration characteristics, particularly damping ratio, of the pump shaft to a great extent to make the pump more aseismatic. (4) In the evaluation of the underwater bearing characteristics of the wear ring, the evaluation accuracy of the vibration characteristics of the pump shaft can be improved by taking into consideration the pressure loss in the wear ring part from the head of the single stage of the pump due to the rotation of the impeller. (author)

Effect of pressure on thermopower and resistivity of EuCo2P2

International Nuclear Information System (INIS)

Nakama, T; Yoshida, T; Ohno, A; Nakamura, D; Takaesu, Y; Hedo, M; Yagasaki, K; Uchima, K; Fujiwara, T; Shigeoka, T

2010-01-01

The measurements of electrical resistivity ρ and thermopower S of the single-crystalline EuCo 2 P 2 have been performed at temperatures from 2 K to 300 K under hydrostatic pressures up to 3 GPa. The temperature dependence of ρ and S show drastic changes at the critical pressure P c , indicating a large modification of electronic structure around the Fermi level due to a pressure-induced structural and magnetic phase transition. The magnetic phase transition temperature increases linearly with increasing pressure, and shows a sudden increase at the critical pressure P c , which correspond to the change of magnetic state from the localized Eu(4f) sub-lattice magnetism into the itinerant Co(3d) sub-lattice magnetism.

Electrical resistivity of CeNiSn under uniaxial and hydrostatic pressures

Science.gov (United States)

Echizen, Y.; Umeo, K.; Igaue, T.; Takabatake, T.

2002-05-01

We present measurements of the electrical resistivity ρ(T) on high-quality single-crystalline CeNiSn under both hydrostatic pressure up to 1 GPa and uniaxial pressure up to 0.25 GPa. At ambient pressure, ρ(T) along the orthorhombic a-axis (b-axis) shows two maxima at TL = 12 K (14 K) and TH = 74 K (40 K), respectively, which arise from the Kondo scattering of conduction electrons by the crystal-field ground state and excited states. With increasing hydrostatic pressure, both TL and TH increase linearly, and for P≥0.8 GPa, the anisotropy in ρ(T) for I∥a and I∥b almost vanishes as a result of increased hybridization between the 4f electrons and the conduction electrons. Under P∥a, both TL and TH in ρ(I∥b) increase similarly to under hydrostatic pressure. Under P∥c, however, the depression of TL in ρ(I∥a) and ρ(I∥b) suggests that the c-f hybridization in the crystal-field ground state is weakened in the a-b plane of CeNiSn.

Conductive core of radiation-resistant high-pressure electric bushing, especially for nuclear technology

International Nuclear Information System (INIS)

Zajic, V.

1981-01-01

A radiation-resistant high-pressure electric bushing was developed featuring a conductive core consisting of a hollow moulding. At the point of attachment to the bushing insulator the core moulding is widened, thus forming a ring support of a diameter larger by at least 10% than the diameter of the conductive core cylindrical section. On the outer side of the pressure body the core cavity is narrowed and tightly closed with the conductor. On the side facing the medium of higher pressure, the conductive core is provided with a thread. Core manufacture and connection of the conductor to the bushing is very simple. The bushing can be used for an environment with pressures exceeding 10 MPa. (J.B.)

Conductive core of radiation-resistant high-pressure electric bushing, especially for nuclear technology

Energy Technology Data Exchange (ETDEWEB)

Zajic, V

1981-09-01

A radiation-resistant high-pressure electric bushing was developed featuring a conductive core consisting of a hollow moulding. At the point of attachment to the bushing insulator the core moulding is widened, thus forming a ring support of a diameter larger by at least 10% than the diameter of the conductive core cylindrical section. On the outer side of the pressure body the core cavity is narrowed and tightly closed with the conductor. On the side facing the medium of higher pressure, the conductive core is provided with a thread. Core manufacture and connection of the conductor to the bushing is very simple. The bushing can be used for an environment with pressures exceeding 10 MPa.

Dependence of temperature-dependent electrical resistivity of SrIrO3 on hydrostatic pressure to 9.1 kbar

International Nuclear Information System (INIS)

Foroozani, N.; Lim, J.; Li, L.; Cao, G.; Schilling, J.S.

2013-01-01

Non-Fermi-liquid behavior and close proximity to a quantum critical point in the 5d transition metal iridate SrIrO 3 at ambient pressure motivate our search for possible anomalous behavior in its transport properties under pressure. The electrical resistivity in the ab-plane of a single crystal of SrIrO 3 has been measured over the temperature range 1.35–285 K at both ambient and 9.1 kbar hydrostatic pressure. The resistivity decreases slightly over the entire temperature range, but no superconducting transition or changes in the non-Fermi-liquid behavior are observed under pressure. It is estimated that significantly higher pressures are likely required before sizable changes in the properties of SrIrO 3 will occur.

Glued versus stapled anastomosis of the colon: An experimental study to determine comparative resistance to intraluminal pressure

Directory of Open Access Journals (Sweden)

Jiri Paral

2014-07-01

Conclusion: Healing with absorbable synthetic glue was as good as with staples. Glued anastomoses resisted pressures that were statistically significantly higher than physiological intraluminal colon pressures but lower than stapled ones.

Pressure Response of Various Gases in a Pneumatic Resistance Capacitance System and Pipe

Science.gov (United States)

Peng, J.; Youn, C.; Tadano, K.; Kagawa, T.

2017-10-01

City gas, such as propane and methane, is widely used as a fuel in households and factories. Recently, hydrogen as a clean and efficient fuel has been proposed for fuel cell vehicles. However, few studies have investigated pressure control and response of gases considering their properties. This study investigated the static flow rate characteristics in an orifice with four gases—air, propane, methane, and hydrogen. Then, a pressure response experiment was performed using a pneumatic resistance capacitance system comprising an isothermal chamber and a nozzle flapper, and the time constant of the pressure response with various gases was analysed with a mathematical model. The simulation results agreed with the experimental data. Finally, the differences in pressure propagation in a pipe with various gases were explicated by a pressure response experiment. The results showed that the pressure response speed of hydrogen is faster than that of the other three gases because of its small molecular weight. Therefore, the pressure control equipment of hydrogen needs a high response speed.

Pressure Resistance Welding of High Temperature Metallic Materials

International Nuclear Information System (INIS)

Jerred, N.; Zirker, L.; Charit, I.; Cole, J.; Frary, M.; Butt, D.; Meyer, M.; Murty, K.L.

2010-01-01

Pressure Resistance Welding (PRW) is a solid state joining process used for various high temperature metallic materials (Oxide dispersion strengthened alloys of MA957, MA754; martensitic alloy HT-9, tungsten etc.) for advanced nuclear reactor applications. A new PRW machine has been installed at the Center for Advanced Energy Studies (CAES) in Idaho Falls for conducting joining research for nuclear applications. The key emphasis has been on understanding processing-microstructure-property relationships. Initial studies have shown that sound joints can be made between dissimilar materials such as MA957 alloy cladding tubes and HT-9 end plugs, and MA754 and HT-9 coupons. Limited burst testing of MA957/HT-9 joints carried out at various pressures up to 400 C has shown encouraging results in that the joint regions do not develop any cracking. Similar joint strength observations have also been made by performing simple bend tests. Detailed microstructural studies using SEM/EBSD tools and fatigue crack growth studies of MA754/HT-9 joints are ongoing.

Debris filtering effectiveness and pressure drop tests of debris resistance-bottom end piece

International Nuclear Information System (INIS)

Chung, Moon Ki; Song, Chul Hwa; Chung, Heung June; Won, Soon Yeun; Cho, Young Ro; Kim, Bok Deuk

1992-03-01

In this final report, described are the test conditions and test procedures for the debris filtering effectiveness and pressure drop tests for developing the Debris Resistance-Bottom End Piece (DR-BEP). And the test results are tabulated for later evaluation. (Author)

Radiation-resistant pressure transducers

International Nuclear Information System (INIS)

Abbasov, Sh.M.; Kerimova, T.I.

2005-01-01

Full text : The sensitive element of vibrofrequency tensor converter (VTC) is an electromechanical resonator of string type with electrostatic excitation of longitudinal mechanical vibrations. The string is made from tensosensitive thread-like monocrystal n-Ge1-x Six (length 1-5 mm, diameter 8-12 mcm) with current outlet and strictly fixed by ends at plate or deformable surface (in elastic element) at 50 mcm apartheid. With increasing Si atomic percent in n-Ge1-x Six the converter tens sensitivity increases. There has been shown the scheme of pressure transducer which contains monocrystalline silicon membrane and string tens converter from thread-like monocrystal Ge-Si. Using method, when crystal position on membrane while it deforms by pressure, corresponds to free (uptight) state, allowed to obtain the maximum sensitivity in measurement of pressure fluctuation. The transducers of absolute and pressure differential of this type can be used in automated systems of life activity. The high sensitivity of string transducers to pressure exceeding 100 hertz/mm (water column) permits to use them in devices for measuring gas concentration. The combination of optical and deformation methods of measurements forms the basis of their operation. The pressure change occurs due to the fact that gas molecules absorbing the quanta of incident light, become at excited state and then excitation energy of their vibrational-rotatory degrees of freedom converts to the energy of translational motion of molecules, i.e. to heat appropriate to pressure increase. Using these tens converters of high pressure one can prevent the possible accidents on oil pipe-like Baku-Tibilisi-Ceyhan

42 CFR 84.157 - Airflow resistance test; Type C supplied-air respirator, pressure-demand class; minimum...

Science.gov (United States)

2010-10-01

... test; Type C supplied-air respirator, pressure-demand class; minimum requirements. (a) The static... 42 Public Health 1 2010-10-01 2010-10-01 false Airflow resistance test; Type C supplied-air respirator, pressure-demand class; minimum requirements. 84.157 Section 84.157 Public Health PUBLIC HEALTH...

Resistance exercise with different volumes: blood pressure response and forearm blood flow in the hypertensive elderly

Directory of Open Access Journals (Sweden)

Brito AF

2014-12-01

Full Text Available Aline de Freitas Brito,1 Caio Victor Coutinho de Oliveira,2 Maria do Socorro Brasileiro-Santos,1 Amilton da Cruz Santos1 1Physical Education Department, 2Research Laboratory for Physical Training Applied to Performance and Health, Federal University of Paraíba, João Pessoa, Brazil Background: The purpose of this study was to evaluate the effect of two sessions of resistance exercise with different volumes on post-exercise hypotension, forearm blood flow, and forearm vascular resistance in hypertensive elderly subjects.Methods: The study was conducted with ten hypertensive elderly (65±3 years, 28.7±3 kg/m2 subjected to three experimental sessions, ie, a control session, exercise with a set (S1, and exercise with three sets (S3. For each session, the subjects were evaluated before and after intervention. In the pre-intervention period, blood pressure, forearm blood flow, and forearm vascular resistance were measured after 10 minutes of rest in the supine position. Thereafter, the subjects were taken to the gym to perform their exercise sessions or remained at rest during the same time period. Both S1 and S3 comprised a set of ten repetitions of ten exercises, with an interval of 90 seconds between exercises. Subsequently, the measurements were again performed at 10, 30, 50, 70, and 90 minutes of recovery (post-intervention in the supine position.Results: Post-exercise hypotension was greater in S3 than in S1 (systolic blood pressure, −26.5±4.2 mmHg versus −17.9±4.7 mmHg; diastolic blood pressure, −13.8±4.9 mmHg versus −7.7±5 mmHg, P<0.05. Similarly, forearm blood flow and forearm vascular resistance changed significantly in both sessions with an increase and decrease, respectively, that was more evident in S3 than in S1 (P<0.05.Conclusion: Resistance exercises with higher volume were more effective in causing post-exercise hypotension, being accompanied by an increase in forearm blood flow and a reduction of forearm vascular

Pressure effect on electrical resistivity of Y1-xGdxCo2

International Nuclear Information System (INIS)

Nakama, T.; Takaesu, Y.; Yagasaki, K.; Sakai, E.; Kurita, N.; Hedo, M.; Uwatoko, Y.; Burkov, A.T.

2006-01-01

Electrical resistivity of Y 1-x Gd x Co 2 alloy system has been measured at temperatures from 2 to 300K in magnetic field up to 15T and under pressure up to 10GPa. The compounds with the composition near to phase boundary between paramagnetic and ferromagnetic ground state (x c ∼0.12) show strong enhancement of electrical resistivity at low temperatures. Large positive magnetoresistance was observed in ferromagnetic alloys in composition range 0.15 1-x Gd x Co 2 at low temperatures is in agreement with the variation of magnetoresistance with the composition

Highly stretchable resistive pressure sensors using a conductive elastomeric composite on a micropyramid array.

Science.gov (United States)

Choong, Chwee-Lin; Shim, Mun-Bo; Lee, Byoung-Sun; Jeon, Sanghun; Ko, Dong-Su; Kang, Tae-Hyung; Bae, Jihyun; Lee, Sung Hoon; Byun, Kyung-Eun; Im, Jungkyun; Jeong, Yong Jin; Park, Chan Eon; Park, Jong-Jin; Chung, U-In

2014-06-04

A stretchable resistive pressure sensor is achieved by coating a compressible substrate with a highly stretchable electrode. The substrate contains an array of microscale pyramidal features, and the electrode comprises a polymer composite. When the pressure-induced geometrical change experienced by the electrode is maximized at 40% elongation, a sensitivity of 10.3 kPa(-1) is achieved. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Study on the mould-resistant properties of moso bamboo treated with high pressure and amylase

Science.gov (United States)

Xiao-Dong Huang; Chung-Yun Hse; Todd F. Shupe

2014-01-01

Starch of moso bamboo mainly exists in the elongated parenchyma cells, and it is difficult for amylase to enter moso bamboo and dissolve the starch. Therefore, the mould resistance capability of moso bamboo's products cannot meet the need for bamboo to resist fungal decay. In this experiment, moso bamboo blocks were first treated at six levels of pressure and for...

Experimental investigation into the coupling effects of magnetic field, temperature and pressure on electrical resistivity of non-oriented silicon steel sheet

Science.gov (United States)

Xiao, Lijun; Yu, Guodong; Zou, Jibin; Xu, Yongxiang

2018-05-01

In order to analyze the performance of magnetic device which operate at high temperature and high pressure, such as submersible motor, oil well transformer, the electrical resistivity of non-oriented silicon steel sheets is necessary for precise analysis. But the reports of the examination of the measuring method suitable for high temperature up to 180 °C and high pressure up to 140 MPa are few. In this paper, a measurement system based on four-probe method and Archimedes spiral shape measurement specimens is proposed. The measurement system is suitable for measuring the electrical resistivity of unconventional specimens under high temperature and high pressure and can simultaneously consider the influence of the magnetic field on the electrical resistivity. It can be seen that the electrical resistivity of the non-oriented silicon steel sheets will fluctuate instantaneously when the magnetic field perpendicular to the conductive path of the specimens is loaded or removed. The amplitude and direction of the fluctuation are not constant. Without considering the effects of fluctuations, the electrical resistivity of the non-oriented silicon steel sheets is the same when the magnetic field is loaded or removed. And the influence of temperature on the electrical resistivity of the non-oriented silicon steel sheet is still the greatest even though the temperature and the pressure are coupled together. The measurement results also show that the electrical resistivity varies linearly with temperature, so the temperature coefficient of resistivity is given in the paper.

Metabolic markers associated with insulin resistance predict type 2 diabetes in Koreans with normal blood pressure or prehypertension.

Science.gov (United States)

Sung, Ki-Chul; Park, Hyun-Young; Kim, Min-Ju; Reaven, Gerald

2016-03-22

Questions remain as to the association between essential hypertension and increased incidence of type 2 diabetes (T2DM). The premise of this analysis is that insulin resistance/compensatory hyperinsulinemia is a major predictor of T2DM, and the greater the prevalence of insulin resistance within any population, normotensive or hypertensive, the more likely T2DM will develop. The hypothesis to be tested is that surrogate estimates of insulin resistance will predict incident T2DM to a significant degree in persons with normal blood pressure or prehypertension. Analysis of data from a population-based survey of 10, 038 inhabitants of rural and urban areas of Korea, ≥40 years-old, initiated in 2001, with measures of demographic and metabolic characteristics at baseline and 8-years later. Participants were classified as having normal blood pressure or prehypertension, and three simple manifestations of insulin resistance related to the pathophysiology of T2DM used to predict incident T2DM: (1) glycemia (plasma glucose concentration 2-hour after 75 g oral glucose challenge = 2-hour PG); (2) hyperinsulinemia (plasma insulin concentration 2-hour after 75 g oral glucose challenge = 2-hour PI); and (3) dyslipidemia (ratio of fasting plasma triglyceride/high/density lipoprotein cholesterol concentration = TG/HDL-C ratio). Fully adjusted hazard ratios (HR, 95 % CI) for incident T2DM were highest (P insulin resistance was the 2-hour PI concentration. Subjects with normal blood pressure in the highest quartile of 2-hour PI concentrations were significantly associated with incident T2DM, with HRs of 1.5 (1.02-2.20, P = 0.25) and 2.02 (1.35-3.02, P insulin resistance (glycemia, insulinemia, and dyslipidemia) predict the development of T2DM in patients with either normal blood pressure or prehypertension.

Ultrasensitive and Highly Stable Resistive Pressure Sensors with Biomaterial-Incorporated Interfacial Layers for Wearable Health-Monitoring and Human-Machine Interfaces.

Science.gov (United States)

Chang, Hochan; Kim, Sungwoong; Jin, Sumin; Lee, Seung-Woo; Yang, Gil-Tae; Lee, Ki-Young; Yi, Hyunjung

2018-01-10

Flexible piezoresistive sensors have huge potential for health monitoring, human-machine interfaces, prosthetic limbs, and intelligent robotics. A variety of nanomaterials and structural schemes have been proposed for realizing ultrasensitive flexible piezoresistive sensors. However, despite the success of recent efforts, high sensitivity within narrower pressure ranges and/or the challenging adhesion and stability issues still potentially limit their broad applications. Herein, we introduce a biomaterial-based scheme for the development of flexible pressure sensors that are ultrasensitive (resistance change by 5 orders) over a broad pressure range of 0.1-100 kPa, promptly responsive (20 ms), and yet highly stable. We show that employing biomaterial-incorporated conductive networks of single-walled carbon nanotubes as interfacial layers of contact-based resistive pressure sensors significantly enhances piezoresistive response via effective modulation of the interlayer resistance and provides stable interfaces for the pressure sensors. The developed flexible sensor is capable of real-time monitoring of wrist pulse waves under external medium pressure levels and providing pressure profiles applied by a thumb and a forefinger during object manipulation at a low voltage (1 V) and power consumption (<12 μW). This work provides a new insight into the material candidates and approaches for the development of wearable health-monitoring and human-machine interfaces.

Acute and chronic effects of aerobic exercise on blood pressure in resistant hypertension: study protocol for a randomized controlled trial.

Science.gov (United States)

Nascimento, L S; Santos, A C; Lucena, Jms; Silva, Lgo; Almeida, Aem; Brasileiro-Santos, M S

2017-06-02

Resistant hypertension is a specific condition that affects approximately 10% of subjects with hypertension, and is characterized by persistently high blood pressure levels even using therapy of three or more antihypertensive agents or with blood pressure control using therapy with four or more antihypertensive agents. Changes in lifestyle, such as physical exercise, are indicated for controlling blood pressure. However, investigating studies about this therapy in individuals with resistant hypertension are few. This is a randomized controlled clinical trial. Forty-eight patients with resistant hypertension will be submitted to perform four short-term interventions: aerobic exercise sessions (mild-, moderate- and high-intensity) and control session, in random order and on separate days. After the short-term sessions, the patients will be randomly allocated into four groups for 8 weeks of follow-up: mild-, moderate- and high-intensity aerobic exercise, and a control group. The primary outcome is the occurrence of blood pressure reduction (office and ambulatory analysis, and acute and chronic effects). Secondary outcomes are autonomic and hemodynamic mechanisms: cardiac and vasomotor autonomic modulation, spontaneous baroreflex sensitivity, forearm blood flow and vascular resistance. The importance of exercise for hypertension has been known for decades, but little is known about the effects on patients with resistant hypertension. This study will help to understand whether different aerobic exercise intensities can induce different responses, as well as by what mechanisms adjustments in blood pressure levels may occur. ClinicalTrials.gov, ID: NCT02670681 . Registered on 28 January 2016 (first version); Brazilian Registry Platform Clinical Trials: protocol RBR-5q24zh . Registered on 24 June 2015.

Resistance training controls arterial blood pressure in rats with L-NAME- induced hypertension.

Science.gov (United States)

Araujo, Ayslan Jorge Santos de; Santos, Anne Carolline Veríssimo dos; Souza, Karine dos Santos; Aires, Marlúcia Bastos; Santana-Filho, Valter Joviniano; Fioretto, Emerson Ticona; Mota, Marcelo Mendonça; Santos, Márcio Roberto Viana

2013-04-01

Arterial hypertension is a multifactorial chronic condition caused by either congenital or acquired factors. To evaluate the effects of Resistance Training (RT) on arterial pressure, and on vascular reactivity and morphology, of L-NAME-treated hypertensive rats. Male Wistar rats (200 - 250 g) were allocated into Sedentary Normotensive (SN), Sedentary Hypertensive (SH) and Trained Hypertensive (TH) groups. Hypertension was induced by adding L-NAME (40 mg/Kg) to the drinking water for four weeks. Arterial pressure was evaluated before and after RT. RT was performed using 50% of 1RM, 3 sets of 10 repetitions, 3 times per week for four weeks. Vascular reactivity was measured in rat mesenteric artery rings by concentration-response curves to sodium nitroprusside (SNP); phenylephrine (PHE) was also used for histological and stereological analysis. Resistance training inhibited the increase in mean and diastolic arterial pressures. Significant reduction was observed in Rmax (maximal response) and pD2 (potency) of PHE between SH and TH groups. Arteries demonstrated normal intima, media and adventitia layers in all groups. Stereological analysis demonstrated no significant difference in luminal, tunica media, and total areas of arteries in the SH and TH groups when compared to the SN group. Wall-to-lumen ratio of SH arteries was significantly different compared to SN arteries (parteries. RT was able to prevent an increase in blood pressure under the conditions in this study. This appears to involve a vasoconstrictor regulation mechanism and maintenance of luminal diameter in L-NAME induced hypertensive rats.

Investigation of the Neutral Gas Pressure Effect on the Metal Resistive Bolometer

International Nuclear Information System (INIS)

Zhang, D.; Giannone, L.; Piechotka, M.; Windisch, T.; Klinger, T.; Grulke, O.; Stark, A.

2008-01-01

The bolometer system planned for W7-X consists mainly of metal (Au) resistive detector arrays. All the detectors are exposed to neutral gas environment. The thin bolometer foil used for detecting the radiated power loss may be sensitive to the neutral gas pressure due to the strain gauge effect. Recently, a prototype of this kind of bolometer camera consisting of 12 channels has been installed on the cylindrical plasma device VINETA in order to investigate the influences of the neutral gas pressure on the bolometer signals. Experiments are carried out for Ar-discharges under different gas pressure conditions. It is found that the pressure effect of the neutral gas can make considerable contributions, thus inducing non-negligible errors of the results in most of the investigated cases. Using the VINETA plasmas (Ar, T e e -19 m -3 ) as examples, the paper demonstrates and discusses how to minimize the neutral gas effects, especially in the data analysis process. The radiated power and the radiation intensity profile obtained in helicon discharges are presented

Investigation of the Neutral Gas Pressure Effect on the Metal Resistive Bolometer

Science.gov (United States)

Zhang, D.; Giannone, L.; Grulke, O.; Piechotka, M.; Windisch, T.; Stark, A.; Klinger, T.

2008-03-01

The bolometer system planned for W7-X consists mainly of metal (Au) resistive detector arrays. All the detectors are exposed to neutral gas environment. The thin bolometer foil used for detecting the radiated power loss may be sensitive to the neutral gas pressure due to the strain gauge effect. Recently, a prototype of this kind of bolometer camera consisting of 12 channels has been installed on the cylindrical plasma device VINETA in order to investigate the influences of the neutral gas pressure on the bolometer signals. Experiments are carried out for Ar-discharges under different gas pressure conditions. It is found that the pressure effect of the neutral gas can make considerable contributions, thus inducing non-negligible errors of the results in most of the investigated cases. Using the VINETA plasmas (Ar, Te<10 eV, ne<10-19 m-3) as examples, the paper demonstrates and discusses how to minimize the neutral gas effects, especially in the data analysis process. The radiated power and the radiation intensity profile obtained in helicon discharges are presented.

Model of the coronary circulation based on pressure dependence of coronary resistance and compliance

NARCIS (Netherlands)

Bruinsma, P.; Arts, T.; Dankelman, J.; Spaan, J. A.

1988-01-01

The effect of pressure-dependent changes in vascular volume, resistance and capacitance in the coronary micro-circulation, has been studied by a distributed mathematical model of the coronary micro-vasculature in the left ventricular wall. The model does not include regulation of coronary blood flow

Pressure dependence of resistivity and magnetic properties in a Mn1.9Cr0.1Sb alloy

Directory of Open Access Journals (Sweden)

D. V. Maheswar Repaka

2017-12-01

Full Text Available We report magnetic-field and hydrostatic pressure dependent electrical resistivity and magnetic properties of a Mn1.9Cr0.1Sb alloy. Upon cooling, the magnetization of Mn1.9Cr0.1Sb exhibits a first-order ferrimagnetic to antiferromagnetic transition at the exchange inversion temperature, TS = 261 K under a 0.1 T magnetic field. Our experimental results show that TS decreases with increasing magnetic field but increase with increasing hydrostatic pressure. The pressure induced transition is accompanied by a large positive baro-resistance of 30.5% for a hydrostatic pressure change of 0.69 GPa. These results show that the lattice parameters as well as the bond distance between Mn-Mn atoms play a crucial role in the magnetic and electronic transport properties of Mn1.9Cr0.1Sb. This sample also exhibits a large inverse magnetocaloric effect with a magnetic entropy change of ΔSm = +6.75 J/kg.K and negative magnetoresistance (44.5% for a field change of 5 T at TS in ambient pressure which may be useful for magnetic cooling and spintronics applications.

Electrical resistivity of U/sub 1/minus/x/M/sub x/Be13 under pressure

International Nuclear Information System (INIS)

Borges, H.A.; Thompson, J.D.; Aronson, M.C.; Fisk, Z.; Smith, J.L.

1988-01-01

Measurements of the electrical resistivity of U/sub 1/minus/x/ Th/sub x/ Be 13 compounds as a function of pressure provide a possible explanation for the unusual behavior of these materials. 10 refs., 2 figs

Tetracycline resistance genes persist in soil amended with cattle feces independently from chlortetracycline selection pressure

NARCIS (Netherlands)

Kyselkova, Martina; Kotrbova, Lucie; Bhumibhamon, Gamonsiri; Chronakova, Alica; Jirout, Jiri; Vrchotova, Nadezda; Schmitt, Heike; Elhottova, Dana

Antibiotic residues and antibiotic resistance genes originating from animal waste represent environmental pollutants with possible human health consequences. In this study, we addressed the question whether chlortetracycline (CTC) residues in soils can act as selective pressure enhancing the

Effect of CPAP on blood pressure in patients with obstructive sleep apnea and resistant hypertension: the HIPARCO randomized clinical trial.

Science.gov (United States)

Martínez-García, Miguel-Angel; Capote, Francisco; Campos-Rodríguez, Francisco; Lloberes, Patricia; Díaz de Atauri, María Josefa; Somoza, María; Masa, Juan F; González, Mónica; Sacristán, Lirios; Barbé, Ferrán; Durán-Cantolla, Joaquín; Aizpuru, Felipe; Mañas, Eva; Barreiro, Bienvenido; Mosteiro, Mar; Cebrián, Juan J; de la Peña, Mónica; García-Río, Francisco; Maimó, Andrés; Zapater, Jordi; Hernández, Concepción; Grau SanMarti, Nuria; Montserrat, Josep María

2013-12-11

More than 70% of patients with resistant hypertension have obstructive sleep apnea (OSA). However, there is little evidence about the effect of continuous positive airway pressure (CPAP) treatment on blood pressure in patients with resistant hypertension. To assess the effect of CPAP treatment on blood pressure values and nocturnal blood pressure patterns in patients with resistant hypertension and OSA. Open-label, randomized, multicenter clinical trial of parallel groups with blinded end point design conducted in 24 teaching hospitals in Spain involving 194 patients with resistant hypertension and an apnea-hypopnea index (AHI) of 15 or higher. Data were collected from June 2009 to October 2011. CPAP or no therapy while maintaining usual blood pressure control medication. The primary end point was the change in 24-hour mean blood pressure after 12 weeks. Secondary end points included changes in other blood pressure values and changes in nocturnal blood pressure patterns. Both intention-to-treat (ITT) and per-protocol analyses were performed. A total of 194 patients were randomly assigned to receive CPAP (n = 98) or no CPAP (control; n = 96). The mean AHI was 40.4 (SD, 18.9) and an average of 3.8 antihypertensive drugs were taken per patient. Baseline 24-hour mean blood pressure was 103.4 mm Hg; systolic blood pressure (SBP), 144.2 mm Hg; and diastolic blood pressure (DBP), 83 mm Hg. At baseline, 25.8% of patients displayed a dipper pattern (a decrease of at least 10% in the average nighttime blood pressure compared with the average daytime blood pressure). The percentage of patients using CPAP for 4 or more hours per day was 72.4%. When the changes in blood pressure over the study period were compared between groups by ITT, the CPAP group achieved a greater decrease in 24-hour mean blood pressure (3.1 mm Hg [95% CI, 0.6 to 5.6]; P = .02) and 24-hour DBP (3.2 mm Hg [95% CI, 1.0 to 5.4]; P = .005), but not in 24-hour SBP (3.1 mm Hg [95% CI, -0.6 to 6

Influence of high sintering pressure on the microhardness and wear resistance of diamond powder and silicon carbide-based composites

Directory of Open Access Journals (Sweden)

Osipov Oleksandr Sergueevitch

2004-01-01

Full Text Available The work reported on here involved the development of several samples of "diamond-SiC" composite produced under sintering pressures of up to 9.0 GPa at temperatures of up to 1973 7K. The average size of the diamond micropowder crystals used was 40/28 µm. The sintering process was carried out in a 2500-ton hydraulic press equipped with an anvil-type high-pressure device having a toroidal work surface and a central concavity diameter of 20 mm. The microhardness and wear resistance of the samples were found to be dependent on the sintering pressure. The experimental results indicated that the maximum microhardness and minimum wear resistance coefficients of each compact were attained when the pressure applied during sintering exceeded 6.5 GPa. Based on the established values of pressure, this study served to identify the types of devices applicable for the manufacture of composite material inserts for a variety of rock drilling applications.

Analysis of pressure-flow data in terms of computer-derived urethral resistance parameters.

Science.gov (United States)

van Mastrigt, R; Kranse, M

1995-01-01

The simultaneous measurement of detrusor pressure and flow rate during voiding is at present the only way to measure or grade infravesical obstruction objectively. Numerous methods have been introduced to analyze the resulting data. These methods differ in aim (measurement of urethral resistance and/or diagnosis of obstruction), method (manual versus computerized data processing), theory or model used, and resolution (continuously variable parameters or a limited number of classes, the so-called monogram). In this paper, some aspects of these fundamental differences are discussed and illustrated. Subsequently, the properties and clinical performance of two computer-based methods for deriving continuous urethral resistance parameters are treated.

Imaging and modeling of acute pressure-induced changes of collagen and elastin microarchitectures in pig and human resistance arteries.

Science.gov (United States)

Bloksgaard, Maria; Leurgans, Thomas M; Spronck, Bart; Heusinkveld, Maarten H G; Thorsted, Bjarne; Rosenstand, Kristoffer; Nissen, Inger; Hansen, Ulla M; Brewer, Jonathan R; Bagatolli, Luis A; Rasmussen, Lars M; Irmukhamedov, Akhmadjon; Reesink, Koen D; De Mey, Jo G R

2017-07-01

The impact of disease-related changes in the extracellular matrix (ECM) on the mechanical properties of human resistance arteries largely remains to be established. Resistance arteries from both pig and human parietal pericardium (PRA) display a different ECM microarchitecture compared with frequently used rodent mesenteric arteries. We hypothesized that the biaxial mechanics of PRA mirror pressure-induced changes in the ECM microarchitecture. This was tested using isolated pig PRA as a model system, integrating vital imaging, pressure myography, and mathematical modeling. Collagenase and elastase digestions were applied to evaluate the load-bearing roles of collagen and elastin, respectively. The incremental elastic modulus linearly related to the straightness of adventitial collagen fibers circumferentially and longitudinally (both R 2 ≥ 0.99), whereas there was a nonlinear relationship to the internal elastic lamina elastin fiber branching angles. Mathematical modeling suggested a collagen recruitment strain (means ± SE) of 1.1 ± 0.2 circumferentially and 0.20 ± 0.01 longitudinally, corresponding to a pressure of ~40 mmHg, a finding supported by the vital imaging. The integrated method was tested on human PRA to confirm its validity. These showed limited circumferential distensibility and elongation and a collagen recruitment strain of 0.8 ± 0.1 circumferentially and 0.06 ± 0.02 longitudinally, reached at a distending pressure below 20 mmHg. This was confirmed by vital imaging showing negligible microarchitectural changes of elastin and collagen upon pressurization. In conclusion, we show here, for the first time in resistance arteries, a quantitative relationship between pressure-induced changes in the extracellular matrix and the arterial wall mechanics. The strength of the integrated methods invites for future detailed studies of microvascular pathologies. NEW & NOTEWORTHY This is the first study to quantitatively relate pressure

INVESTIGATION OF MATERIAL RESISTANCE TO PLASTIC DEFORMATION AT PROCESSING METALS BY PRESSURE WITH IMPOSING ULTRASONIC OSCILLATIONS

Directory of Open Access Journals (Sweden)

V. V. Klubovich

2007-01-01

Full Text Available The paper contains substantiation for application of experimental technique in order to investigate material resistance to plastic deformation at processing metals by pressure with imposing ultrasonic oscillations while proceeding from laws of similarity. It is shown that at modeling any metal processing by pressure with imposing ultrasonic oscillations it is possible to consider that actual elastic and plastic metal properties remain constant during processing under ultrasound action. The second aspect that requires a special attention at modeling is pulse or vibration-shock deformation at processing metals by pressure with imposing ultrasonic oscillations.

Leptin receptor blockade reduces intrahepatic vascular resistance and portal pressure in an experimental model of rat liver cirrhosis.

Science.gov (United States)

Delgado, María Gabriela; Gracia-Sancho, Jordi; Marrone, Giusi; Rodríguez-Vilarrupla, Aina; Deulofeu, Ramon; Abraldes, Juan G; Bosch, Jaume; García-Pagán, Juan Carlos

2013-10-01

Increased hepatic vascular resistance mainly due to elevated vascular tone and to fibrosis is the primary factor in the development of portal hypertension in cirrhosis. Leptin, a hormone associated with reduction in nitric oxide bioavailability, vascular dysfunction, and liver fibrosis, is increased in patients with cirrhosis. We aimed at evaluating whether leptin influences the increased hepatic resistance in portal hypertension. CCl4-cirrhotic rats received the leptin receptor-blocker ObR antibody, or its vehicle, every other day for 1 wk. Hepatic and systemic hemodynamics were measured in both groups. Hepatic nitric oxide production and bioavailability, together with oxidative stress, nitrotyrosinated proteins, and liver fibrosis, were evaluated. In cirrhotic rats, leptin-receptor blockade significantly reduced portal pressure without modifying portal blood flow, suggesting a reduction in the intrahepatic resistance. Portal pressure reduction was associated with increased nitric oxide bioavailability and with decreased O2(-) levels and nitrotyrosinated proteins. No changes in systemic hemodynamics and liver fibrosis were observed. In conclusion, the present study shows that blockade of the leptin signaling pathway in cirrhosis significantly reduces portal pressure. This effect is probably due to a nitric oxide-mediated reduction in the hepatic vascular tone.

Sensitivity and specificity of hypopnoea detection using nasal pressure in the presence of a nasal expiratory resistive device (Provent®)

International Nuclear Information System (INIS)

Milne, Stephen; Amis, Terence C; Wheatley, John R; Kairaitis, Kristina

2014-01-01

Nasal expiratory resistive valves (Provent ® ) have been proposed as novel therapy for obstructive sleep apnea. We compared pressure measurements from a standard nasal pressure catheter used to assess nasal airflow during sleep with those from nasal expiratory resistive device with attached proprietary nasal pressure cannula. Nasal pressure cannula or Provent ® + proprietary nasal pressure cannula were attached to a bench model of human anterior nares and nasal passages, and pressure measured (P). Respiratory airflows generated by a subject breathing were applied to rear of model and airflow ( V-dot ) measured via pneumotachograph. Airflow amplitude (Δ V-dot ) was plotted against pressure amplitude (ΔP). Hypopnoea detection (<50% Δ V-dot ) sensitivity and specificity was tested by expressing ΔP in terms of two reference breaths: reference breath 1, Δ V-dot 0.55 L s −1  = 100%; and reference breath 2, Δ V-dot 0.45 L s −1  = 100%. ΔP/Δ V-dot relationships were linear for Δ V-dot  ≤ 0.55 L s −1 ; ΔP = 0.37ΔV + 0.16 (nasal pressure cannula), ΔP = 2.7ΔV + 0.12 (Provent ® + proprietary nasal pressure cannula); both R 2  > 0.65, p < 0.0001; p < 0.0001 for between slope difference). For nasal pressure cannula, specificity of hypopnoea detection differed between reference breaths one and two (80.2% and 40.0%, respectively), and Provent ® + proprietary nasal pressure cannula (30.3% and 74.2%, respectively). Quantification of airflow obstruction in the presence of Provent ® + proprietary nasal pressure cannula is greatly influenced by the reference breath chosen to determine a reduction in nasal airflow. Reported variability in therapeutic response to nasal expiratory resistive devices may relate to differences in measurement technique specificity used to quantify the severity of sleep disordered breathing. (paper)

The Role of Hyperglycemia, Insulin Resistance, and Blood Pressure in Diabetes-Associated Differences in Cognitive Performance-The Maastricht Study.

Science.gov (United States)

Geijselaers, Stefan L C; Sep, Simone J S; Claessens, Danny; Schram, Miranda T; van Boxtel, Martin P J; Henry, Ronald M A; Verhey, Frans R J; Kroon, Abraham A; Dagnelie, Pieter C; Schalkwijk, Casper G; van der Kallen, Carla J H; Biessels, Geert Jan; Stehouwer, Coen D A

2017-11-01

To study to what extent differences in cognitive performance between individuals with different glucose metabolism status are potentially attributable to hyperglycemia, insulin resistance, and blood pressure-related variables. We used cross-sectional data from 2,531 participants from the Maastricht Study (mean age ± SD, 60 ± 8 years; 52% men; n = 666 with type 2 diabetes), all of whom completed a neuropsychological test battery. Hyperglycemia was assessed by a composite index of fasting glucose, postload glucose, glycated hemoglobin (HbA 1c ), and tissue advanced glycation end products; insulin resistance by the HOMA of insulin resistance index; and blood pressure-related variables included 24-h ambulatory pressures, their weighted SDs, and the use of antihypertensive medication. Linear regression analyses were used to estimate mediating effects. After adjustment for age, sex, and education, individuals with type 2 diabetes, compared with those with normal glucose metabolism, performed worse in all cognitive domains (mean differences in composite z scores for memory -0.087, processing speed -0.196, executive function and attention -0.182; P values <0.032), whereas individuals with prediabetes did not. Diabetes-associated differences in processing speed and executive function and attention were largely explained by hyperglycemia (mediating effect 79.6% [bootstrapped 95% CI 36.6; 123.4] and 50.3% [0.6; 101.2], respectively) and, for processing speed, to a lesser extent by blood pressure-related variables (17.7% [5.6; 30.1]), but not by insulin resistance. None of the factors explained the differences in memory function. Our cross-sectional data suggest that early glycemic and blood pressure control, perhaps even in the prediabetic stage, may be promising therapeutic targets for the prevention of diabetes-associated decrements in cognitive performance. © 2017 by the American Diabetes Association.

[Correlation of resistance to peer pressure and risky decision-making with adolescent health risk behaviors].

Science.gov (United States)

An, Jing; Sun, Ying; Wang, Xi; Zu, Ping; Mai, Jin-cheng; Liang, Jian-ping; Xu, Zhi-yong; Man, Xue-jun; Mao, Yan; Tao, Fang-biao

2013-03-01

To explore possible interrelationships among resistance to peer pressure, risky decision-making and health risk behaviors among young adolescents. Based on the cluster sampling method, the participants who were recruited from 5 junior middle schools in Guangzhou and 3 junior middle schools in Shenyang city on October, 2010, were administered to complete the questionnaire concerned with their experiences with drinking and smoking during the past 30 days preceding the survey, and the hours using computer daily both in weekdays and in weekend. The level of resistance to peer influence and risky decision-making were assessed by Resistance to peer influence scale (RPIS) and Youth decision-making questionnaire (YDMQ). Logistic regression was used to explore possible interrelationships among resistance to peer influence, risky decision-making and health risk behaviors among young adolescents. A total of 1985 questionnaires were valid, including 1001(50.4%) boys and 984 (49.6%) girls. About 27.1% (537/1985) junior middle school students reported having health risk behaviors, boys' (30.7%, 307/1001) was higher than girls' (23.4%, 230/984) with significant gender difference (P peer influence (low and middle level vs high level, had odds ratios of 2.97 (1.96 - 4.50) and 1.51 (1.05 - 2.16)), and also the middle and high level of risky decision-making (middle and high level vs low level, had odds ratios of 1.62 (1.19 - 2.22) and 3.43 (2.39 - 4.90)) were all the risk factors of adolescent health risk behaviors. Adolescents with poor ability of resistance to peer pressure and high risky decision-making were both the risk factors of adolescent health risk behaviors.

Fatigue resistance of rotary ProTaper Universal instruments after use with and without lateral pressure motion

OpenAIRE

Vieira, Evandro Pires; Pereira, Érika Sales Joviano; Peixoto, Isabella Faria da Cunha; Buono, Vicente Tadeu Lopes; Bahia, Maria Guiomar de Azevedo

2016-01-01

Aim: To evaluate the fatigue resistance of rotary ProTaper Universal instruments after multiple clinical uses with and without lateral pressure motion. Methods: Thirty sets of ProTaper Universal (PTU) instruments (Dentsply-Maillefer, Ballaigues, Switzerland), types S1, S2, F1 and F2, totaling 120 files, were analyzed and divided into three groups, as follows: Control Group (CG), with 10 sets of new instruments, which were fatigue tested until rupture to determine their fatigue resistance; Lat...

Effects of selection pressure and genetic association on the relationship between antibiotic resistance and virulence in Escherichia coli.

Science.gov (United States)

Zhang, Lixin; Levy, Karen; Trueba, Gabriel; Cevallos, William; Trostle, James; Foxman, Betsy; Marrs, Carl F; Eisenberg, Joseph N S

2015-11-01

Antibiotic selection pressure and genetic associations may lead to the cooccurrence of resistance and virulence in individual pathogens. However, there is a lack of rigorous epidemiological evidence that demonstrates the cooccurrence of resistance and virulence at the population level. Using samples from a population-based case-control study in 25 villages in rural Ecuador, we characterized resistance to 12 antibiotics among pathogenic (n = 86) and commensal (n = 761) Escherichia coli isolates, classified by the presence or absence of known diarrheagenic virulence factor genes. The prevalences of resistance to single and multiple antibiotics were significantly higher for pathogenic isolates than for commensal isolates. Using a generalized estimating equation, antibiotic resistance was independently associated with virulence factor carriage, case status, and antibiotic use (for these respective factors: odds ratio [OR] = 3.0, with a 95% confidence interval [CI] of 1.7 to 5.1; OR = 2.0, with a 95% CI of 1.3 to 3.0; and OR = 1.5, with a 95% CI of 0.9 to 2.5). Virulence factor carriage was more strongly related to antibiotic resistance than antibiotic use for all antibiotics examined, with the exception of fluoroquinolones, gentamicin, and cefotaxime. This study provides epidemiological evidence that antibiotic resistance and virulence factor carriage are linked in E. coli populations in a community setting. Further, these data suggest that while the cooccurrence of resistance and virulence in E. coli is partially due to antibiotic selection pressure, it is also genetically determined. These findings should be considered in developing strategies for treating infections and controlling for antibiotic resistance. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

Experimental Studies on the Changes in Resistivity and Its Anisotropy Using Electrical Resistivity Tomography

Directory of Open Access Journals (Sweden)

Tao Zhu

2012-01-01

Full Text Available Three measuring lines were arranged on one of free planes of magnetite cuboid samples. Apparent resistivity data were acquired by MIR-2007 resistivity meter when samples were under uniaxial compression of servocontrol YAW-5000F loadingmachine in laboratory. Then we constructed the residual resistivity images using electrical resistivity tomography (ERT and plotted the diagrams of apparent resistivity anisotropy coefficient (ARAC λ∗ and the included angle α between the major axis of apparent resistivity anisotropy ellipse and the axis of load with pressure and effective depth. Our results show that with increasing pressure, resistivity and the decreased (D region and increased (I region resistivity regions have complex behaviors, but when pressure is higher than a certain value, the average resistivity decrease and the area of D region expand gradually in all time with the increase of pressure, which may be significant to the monitoring and prediction of earthquake, volcanic activities, and large-scale geologic motions. The effects of pressure on λ∗ and α are not very outstanding for dry magnetite samples.

Models for ductile crack initiation and tearing resistance under mode 1 loading in pressure vessel steels

International Nuclear Information System (INIS)

Jones, M.R.

1988-06-01

Micromechanistic models are presented which aim to predict plane strain ductile initiation toughness, tearing resistance and notched bar fracture strains in pressure vessel steels under monotonically increasing tensile (mode 1) loading. The models for initiation toughness and tearing resistance recognize that ductile fracture proceeds by the growth and linkage of voids with the crack-tip. The models are shown to predict the trend of initiation toughness with inclusion spacing/size ratio and can bound the available experimental data. The model for crack growth can reproduce the tearing resistance of a pressure vessel steel up to and just beyond crack growth initiation. The fracture strains of notched bars pulled in tension are shown to correspond to the achievement of a critical volume fraction of voids. This criterion is combined with the true stress - true strain history of a material point ahead of a blunting crack-tip to predict the initiation toughness. An attempt was made to predict the fracture strains of notched tensile bars by adopting a model which predicts the onset of a shear localization phenomenon. Fracture strains of the correct order are computed only if a ''secondary'' void nucleation event at carbide precipitates is taken into account. (author)

Pressure resistance of cold-shocked Escherichia coli O157:H7 in ground beef, beef gravy and peptone water.

Science.gov (United States)

Baccus-Taylor, G S H; Falloon, O C; Henry, N

2015-06-01

(i) To study the effects of cold shock on Escherichia coli O157:H7 cells. (ii) To determine if cold-shocked E. coli O157:H7 cells at stationary and exponential phases are more pressure-resistant than their non-cold-shocked counterparts. (iii) To investigate the baro-protective role of growth media (0·1% peptone water, beef gravy and ground beef). Quantitative estimates of lethality and sublethal injury were made using the differential plating method. There were no significant differences (P > 0·05) in the number of cells killed; cold-shocked or non-cold-shocked. Cells grown in ground beef (stationary and exponential phases) experienced lowest death compared with peptone water and beef gravy. Cold-shock treatment increased the sublethal injury to cells cultured in peptone water (stationary and exponential phases) and ground beef (exponential phase), but decreased the sublethal injury to cells in beef gravy (stationary phase). Cold shock did not confer greater resistance to stationary or exponential phase cells pressurized in peptone water, beef gravy or ground beef. Ground beef had the greatest baro-protective effect. Real food systems should be used in establishing food safety parameters for high-pressure treatments; micro-organisms are less resistant in model food systems, the use of which may underestimate the organisms' resistance. © 2015 The Society for Applied Microbiology.

The Effect of a 4 Week Isometric Handgrip Training on Changes of Peripheral Resistance and Blood Pressure in Women Suffering from Hypertension

Directory of Open Access Journals (Sweden)

N Haji Tehrani

2017-05-01

Full Text Available Introduction: According to many studies, hypertension is considered as the second leading risk factor for coronary artery disease (CAD and cardiac infarction after smoking The purpose of the present study was to investigate the effect of four weeks of Isometric Handgrip (IHG Training on peripheral resistance and hypertension among hypertensive women. Methods: 14 middle aged women, aged 40 to 55 years old, were randomly selected. The training program included 4 sets of 2 minute IHG training with 1 minute resting between each period, performed 3 days a week for four weeks. Doppler ultrasound method was used to measure the vascular resistance. Data were analyzed using paired t-test. Results: According to the results, there was a significant difference between systolic blood pressure (p=0.006 and diastolic blood pressure (p=0.001 after 4 weeks of training. However, no significant difference was observed in vascular resistance (p=0.66. Conclusion: These results demonstrate that IHG training can reduce blood pressure in the hypertensive patients 24 hours after the last training session. It is also revealed that reduced blood pressure is not always associated with reduced vascular resistance and other influential factors may play a role in this regard.

Calculation of Local Stress and Fatigue Resistance due to Thermal Stratification on Pressurized Surge Line Pipe

Science.gov (United States)

Bandriyana, B.; Utaja

2010-06-01

Thermal stratification introduces thermal shock effect which results in local stress and fatique problems that must be considered in the design of nuclear power plant components. Local stress and fatique calculation were performed on the Pressurize Surge Line piping system of the Pressurize Water Reactor of the Nuclear Power Plant. Analysis was done on the operating temperature between 177 to 343° C and the operating pressure of 16 MPa (160 Bar). The stagnant and transient condition with two kinds of stratification model has been evaluated by the two dimensional finite elements method using the ANSYS program. Evaluation of fatigue resistance is developed based on the maximum local stress using the ASME standard Code formula. Maximum stress of 427 MPa occurred at the upper side of the top half of hot fluid pipe stratification model in the transient case condition. The evaluation of the fatigue resistance is performed on 500 operating cycles in the life time of 40 years and giving the usage value of 0,64 which met to the design requirement for class 1 of nuclear component. The out surge transient were the most significant case in the localized effects due to thermal stratification.

Imidacloprid-susceptible Nilaparvata lugens individuals exceeded resistant individuals in a mixture population with density pressure.

Science.gov (United States)

Yu, Na; Tian, Jiahua; Zhang, Yixi; Li, Zhong; Liu, Zewen

2018-01-01

Fitness costs associated with insecticide resistance in pest insects have mainly been studied under optimal laboratory conditions. However, resistant insects face more stressors than just insecticides in the field, and how the resistant population reacts to these stressors is of practical importance for the control of pest insects such as the brown planthopper Nilaparvata lugens. The aim of the present study was to explore the impact of population density on the competitiveness of resistant and susceptible individuals. Two isogenic N. lugens populations, a highly imidacloprid-resistant population (HZ-R) with a resistance ratio (RR) of 227.10 and a relatively susceptible population (HZ-S) with an RR of 2.99, were created from a field-resistant population (HZ; RR 62.51). The high resistance levels of HZ-R and HZ were mainly attributable to the overexpression of multiple cytochrome P450 (CYP) genes such as CYP6ER1, CYP6AY1, CYP6CW1 and CYP4CE1 compared with HZ-S, this being supported by piperonyl butoxide synergism. HZ-R was observed to be more resistant to thiacloprid and etofenprox compared with HZ and HZ-S. Most interestingly, in high population density treatments, HZ-S individuals were much more competitive than HZ-R individuals. Imidacloprid-resistant individuals of N. lugens are less competitive than their susceptible counterparts under density pressure. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Relationship between blood pressure and insulin resistance in patients with gestational diabetes

International Nuclear Information System (INIS)

Kan Shujuan; Zhang Sujuan

2008-01-01

Objective: To study the relationship existe between blood pressure level and degree of insulin resistance in patients with gestational diabetes. Methods: Ninety-five cases of gestational diabetes were diagnosed among 350 pregnant women. Of them, 55 were found to be hypertensive and 40 were normotensive. Fasting, 1,2, 3h post-prandial (75g glucose) blood sugar (with peroxidase method) levels and fasting insulin (with RIA) levels were measured in these patients and 85 normal pregnant women (as control). Results: Fasting, 1, 2, 3h post 75g glucose blood sugar and fasting insulin levels in the 55 hypertensive diabetics were significantly higher than those in the normotensives and controls (P<0.05). The calculated insulin sensitivity indices were significantly lower (P also < 0.05). Conclusion: A higher insulin resistance existed in hypertensive gestational diabetics which might be a risk factor of developing hypertension. (authors)

Analysis of the effect of implemented low temperature overpressure regimes on the reactor pressure vessel resistance to damage

International Nuclear Information System (INIS)

Pistora, V.

1995-12-01

The temperature and stress fields of the Dukovany WWER-440 reactor pressure vessel (RPV) were calculated based on a two-dimensional model using the finite element method. Two pressurized thermal shock events occurred at Dukovany in 1992: the temperature in 3 loops dropped rapidly while the primary circuit was fully pressurized. The calculation revealed that the first event was intolerable with respect to the RPV resistance to brittle fracture; had the two events occurred towards the end of the RPV lifetime, both would have been intolerable. (M.D.). 6 tabs., 15 figs., 6 refs

Resistivity studies on the layered semi-metallic CaAl2Si2: evaluating its temperature-, field- and pressure-dependence

International Nuclear Information System (INIS)

ElMassalami, M; Soares de Oliveira Paixao, L; Chaves, F A B

2011-01-01

We studied the layered, hexagonal, semi-metal CaAl 2 Si 2 by magnetization, specific heat and resistivity measurements over a wide range of temperature, pressure and magnetic field. Both the Sommerfeld coefficient (γ = 1 mJ mol -1 K -2 ) and the Debye temperature (θ D = 288 K) are in agreement with the values obtained from the band structure calculation. The resistivity shows a metallic character up to 200 K, followed by saturation and, afterwards, a weak decrease up to 840 K, at which it sharply rises reaching a local maximum at 847 ± 5 K. While the low-temperature thermal evolution was accounted for in terms of intrinsic and extrinsic effects, the additional high-temperature scattering was attributed, based on differential thermal analysis, to a first-order thermal event. No appreciable magnetoresistivity was observed at liquid helium temperatures even for fields up to 90 kOe, indicating an absence of coupling between the electronic and magnetic degrees of freedom. Finally, an externally applied pressure was found to induce a strong reduction in the resistivity following a second-order polynomial: this effect will be discussed in terms of the influence of pressure on the effective mobility and concentration of charge carriers.

Ultimate internal pressure capacity assessment of SC structure

International Nuclear Information System (INIS)

Park, Hyungkui; Choi, Inkil

2013-01-01

An SC structure applied to a containment building can be quite effective. However, an SC structure cannot be applied to a containment building, because its internal pressure resistance performance has not been verified. The containment building, which undergoes ultimate internal pressure, resists the internal pressure through a pre-stress tendon. It is hard to apply a tendon to an SC structure because of its structural characteristics. Therefore, the internal pressure resistance performance of the SC structure itself should be ensured to apply it to a structure with internal pressure resistance. In this study, the suitability of an SC structure as a substitution for the tendon of a pressure resistant structure was evaluated. A containment structure model was used in this study, because it was representative structures that resistance of ultimate internal pressure be required. In this study, a nonlinear analysis was performed to evaluate and compare the behaviors of tendon model and SC structure model. By comparing the internal pressure-displacement according to the structure type, the stability of SC structure model was assessed

Two-fluid and nonlinear effects of tearing and pressure-driven resistive modes in reversed field pinches

International Nuclear Information System (INIS)

Mirnov, V.V.

2002-01-01

Large-scale tearing instabilities have long been considered to underlie transport and dynamo processes in the reversed field pinch (RFP). The vast majority of theoretical and computational RFP work has focused on pressureless, single-fluid MHD in cylindrical plasmas driven solely by a toroidal electric field. We report results of five investigations covering two-fluid dynamos, toroidal nonlinear MHD computation, nonlinear computation of Oscillating Field Current Drive (OFCD), the effect of shear flow on tearing instability, and the effect of pressure on resistive instability. The key findings are: (1) two-fluid dynamo arising from the Hall term is much larger than the standard MHD dynamo present in a single-fluid treatment, (2) geometric coupling from toroidicity precludes the occurrence of laminar single helicity states, except for nonreversed plasmas, (3) OFCD, a form of AC helicity injection, can sustain the RFP plasma current, although magnetic fluctuations are enhanced, (4) edge shear flow can destabilize the edge resonant m=0 modes, which occur as spikes in experiment, and (5) pressure driven modes are resistive at low beta, only becoming ideal at extremely high beta. (author)

Increased pulse pressure is associated with left atrial enlargement in resistant hypertensive patients.

Science.gov (United States)

Armario, Pedro; Oliveras, Anna; Hernández-Del-Rey, Raquel; Suárez, Carmen; Martell, Nieves; Ruilope, Luis M; De La Sierra, Alejandro

2013-02-01

Resistant hypertension (RH) is frequently associated with a high prevalence of target organ damage, which impairs the prognosis of these patients. Considering cardiac alterations in RH, most attention has been devoted to left ventricular hypertrophy (LVH), but data concerning left atrial enlargement (LAE) is less known. This cross-sectional study assessed the factors associated with LAE, with special focus on blood pressure (BP) estimates obtained by ambulatory blood pressure monitoring (ABPM), in 250 patients with RH, aged 64 ± 11 years. LAE and LVH were observed in 10.0% (95% CI 6.3-13.7) and 57.1% (95% CI 50.8-63.5) of patients, respectively. Compared with patients with normal atrium size, those exhibiting LAE were older, more frequently women, had elevated pulse pressure (PP) measured both at the office and by ABPM, and showed higher prevalence of LVH (83% vs 54%; p = 0.016). In a logistic regression analysis, adjusting for age, gender, body mass index, left ventricular mass index and BP pressure estimates, night-time PP was independently associated with LAE (OR for 5 mmHg = 1.28, 95% CI 1.24-1.32; p = 0.001). In conclusion, besides classical determinants of LAE, such as age and LVH, an elevated night-time PP was independently associated with LAE in patients with RH.

Fracture toughness and crack growth resistance of pressure vessel plate and weld metal steels

International Nuclear Information System (INIS)

Moskovic, R.

1988-01-01

Compact tension specimens were used to measure the initiation fracture toughness and crack growth resistance of pressure vessel steel plates and submerged arc weld metal. Plate test specimens were manufactured from four different casts of steel comprising: aluminium killed C-Mn-Mo-Cu and C-Mn steel and two silicon killed C-Mn steels. Unionmelt No. 2 weld metal test specimens were extracted from welds of double V butt geometry having either the C-Mn-Mo-Cu steel (three weld joints) or one particular silicon killed C-Mn steel (two weld joints) as parent plate. A multiple specimen test technique was used to obtain crack growth data which were analysed by simple linear regression to determine the crack growth resistance lines and to derive the initiation fracture toughness values for each test temperature. These regression lines were highly scattered with respect to temperature and it was very difficult to determine precisely the temperature dependence of the initiation fracture toughness and crack growth resistance. The data were re-analysed, using a multiple linear regression method, to obtain a relationship between the materials' crack growth resistance and toughness, and the principal independent variables (temperature, crack growth, weld joint code and strain ageing). (author)

Effect of hepatic venous sphincter contraction on transmission of central venous pressure to lobar and portal pressure.

Science.gov (United States)

Lautt, W W; Legare, D J; Greenway, C V

1987-11-01

In dogs anesthetized with pentobarbital, central vena caval pressure (CVP), portal venous pressure (PVP), and intrahepatic lobar venous pressure (proximal to the hepatic venous sphincters) were measured. The objective was to determine some characteristics of the intrahepatic vascular resistance sites (proximal and distal to the hepatic venous sphincters) including testing predictions made using a recent mathematical model of distensible hepatic venous resistance. The stimulus used was a brief rise in CVP produced by transient occlusion of the thoracic vena cava in control state and when vascular resistance was elevated by infusions of norepinephrine or histamine, or by nerve stimulation. The percent transmission of the downstream pressure rise to upstream sites past areas of vascular resistance was elevated. Even small increments in CVP are partially transmitted upstream. The data are incompatible with the vascular waterfall phenomenon which predicts that venous pressure increments are not transmitted upstream until a critical pressure is overcome and then further increments would be 100% transmitted. The hepatic sphincters show the following characteristics. First, small rises in CVP are transmitted less than large elevations; as the CVP rises, the sphincters passively distend and allow a greater percent transmission upstream, thus a large rise in CVP is more fully transmitted than a small rise in CVP. Second, the amount of pressure transmission upstream is determined by the vascular resistance across which the pressure is transmitted. As nerves, norepinephrine, or histamine cause the hepatic sphincters to contract, the percent transmission becomes less and the distensibility of the sphincters is reduced. Similar characteristics are shown for the "presinusoidal" vascular resistance and the hepatic venous sphincter resistance.(ABSTRACT TRUNCATED AT 250 WORDS)

A new contact electric resistance technique for in-situ measurement of the electric resistance of surface films on metals in electrolytes at high temperatures and pressures

International Nuclear Information System (INIS)

Saario, T.; Marichev, V.A.

1993-01-01

Surface films play a major role in corrosion assisted cracking. A new Contact Electric Resistance (CER) method has been recently developed for in situ measurement of the electric resistance of surface films. The method has been upgraded for high temperature high pressure application. The technique can be used for any electrically conductive material in any environment including liquid, gas or vacuum. The technique has been used to determine in situ the electric resistance of films on metals during adsorption of water and anions, formation and destruction of oxides and hydrides, electroplating of metals and to study the electric resistance of films on semiconductors. The resolution of the CER technique is 10 -9 Ω, which corresponds to about 0.03 monolayers of deposited copper during electrochemical deposition Cu/Cu 2+ . Electric resistance data can be measured with a frequency of the order of one hertz, which enables one to follow in situ the kinetics of surface film related processes. The kinetics of these processes and their dependence on the environment, temperature, pH and electrochemical potential can be investigated

Resistance pressure sensor based on Ag/Cu/sub 2/O-PEPC-NiPc/Al composite

International Nuclear Information System (INIS)

Khan, A.; Karimov, K.S.; Shah, M.

2011-01-01

This work reports on the fabrication and investigation of pressure sensor based on Ag/Cu/sub 2/O-PEPC-NiPc/Al composite. The active layer of the composite was deposited by drop-casting of the blend Cu/sub 2/O-PEPC-NiPc on flexible substrate. The thin film of the blend consist of cuprous oxide (Cu/sub 2/O) micropowder, (5 wt. %), poly-N-epoxypropyl carbazole (PEPC), (2 wt. %) and nickel phthalocyanine (NiPc) micropowder, (3 wt. %) in benzol (1 ml). The film thickness of the composite is in the range of 20-30 mu m. It is found that the fabricated sensor is sensitive to pressure and showed good repeatability. The decrease in resistance of the sensor is observed 10 times by increasing the external uniaxial pressure up to 11.7 kNm/sup -2/. The experimentally obtained results are compared with the simulated results and showed reasonable agreement with each other. (author)

Endocrine and haemodynamic changes in resistant hypertension, and blood pressure responses to spironolactone or amiloride: the PATHWAY-2 mechanisms substudies.

Science.gov (United States)

Williams, Bryan; MacDonald, Thomas M; Morant, Steve V; Webb, David J; Sever, Peter; McInnes, Gordon T; Ford, Ian; Cruickshank, J Kennedy; Caulfield, Mark J; Padmanabhan, Sandosh; Mackenzie, Isla S; Salsbury, Jackie; Brown, Morris J

2018-04-11

In the PATHWAY-2 study of resistant hypertension, spironolactone reduced blood pressure substantially more than conventional antihypertensive drugs. We did three substudies to assess the mechanisms underlying this superiority and the pathogenesis of resistant hypertension. PATHWAY-2 was a randomised, double-blind crossover trial done at 14 UK primary and secondary care sites in 314 patients with resistant hypertension. Patients were given 12 weeks of once daily treatment with each of placebo, spironolactone 25-50 mg, bisoprolol 5-10 mg, and doxazosin 4-8 mg and the change in home systolic blood pressure was assessed as the primary outcome. In our three substudies, we assessed plasma aldosterone, renin, and aldosterone-to-renin ratio (ARR) as predictors of home systolic blood pressure, and estimated prevalence of primary aldosteronism (substudy 1); assessed the effects of each drug in terms of thoracic fluid index, cardiac index, stroke index, and systemic vascular resistance at seven sites with haemodynamic monitoring facilities (substudy 2); and assessed the effect of amiloride 10-20 mg once daily on clinic systolic blood pressure during an optional 6-12 week open-label runout phase (substudy 3). The PATHWAY-2 trial is registered with EudraCT, number 2008-007149-30, and ClinicalTrials.gov, number NCT02369081. Of the 314 patients in PATHWAY-2, 269 participated in one or more of the three substudies: 126 in substudy 1, 226 in substudy 2, and 146 in substudy 3. Home systolic blood pressure reduction by spironolactone was predicted by ARR (r 2 =0·13, p<0·0001) and plasma renin (r 2 =0·11, p=0·00024). 42 patients had low renin concentrations (predefined as the lowest tertile of plasma renin), of which 31 had a plasma aldosterone concentration greater than the mean value for all 126 patients (250 pmol/L). Thus, 31 (25% [95% CI 17-33]) of 126 patients were deemed to have inappropriately high aldosterone concentrations. Thoracic fluid content was reduced by 6·8% from

The role of hyperglycemia, insulin resistance, and blood pressure in diabetes-associated differences in cognitive performance - The Maastricht study

NARCIS (Netherlands)

Geijselaers, Stefan L C; Sep, Simone J S; Claessens, Danny; Schram, Miranda T; Van Boxtel, Martin P J; Henry, Ronald M. A.; Verhey, Frans R J; Kroon, Abraham A; Dagnelie, Pieter C.; Schalkwijk, Casper G.; van der Kallen, Carla J H; Biessels, Geert Jan; Stehouwer, Coen D. A.

2017-01-01

OBJECTIVE To study to what extent differences in cognitive performance between individuals with different glucose metabolism status are potentially attributable to hyperglycemia, insulin resistance, and blood pressure-related variables. RESEARCH DESIGN AND METHODS We used cross-sectional data from

Exposure to high hydrostatic pressure rapidly selects for increased RpoS activity and general stress-resistance in Escherichia coli O157:H7.

Science.gov (United States)

Vanlint, Dietrich; Rutten, Nele; Govers, Sander K; Michiels, Chris W; Aertsen, Abram

2013-04-15

Exposure to high hydrostatic pressure (HHP) is increasingly being used in food preservation as a non-thermal pasteurization process, and its further implementation necessitates a more thorough understanding of bacterial resistance development and intraspecies variability with regard to inactivation by HHP. In this report, we discovered that exposure to high hydrostatic pressure stress can rapidly select for strongly increased RpoS activity in a hypersensitive Escherichia coli O157:H7 strain (ATCC 43888), leading to a simultaneous increase in HHP and heat resistance. Moreover, the level of RpoS activity correlated well with the original hypersensitivity and the extent of acquired HHP resistance, and extremely HHP-resistant mutants of ATCC 43888 clearly incurred a number of additional RpoS-dependent phenotypes. These findings suggest that implementation of novel processing techniques in the food production chain can readily affect the physiology of food-borne pathogens. Copyright © 2013 Elsevier B.V. All rights reserved.

Coconut Oil Aggravates Pressure Overload-Induced Cardiomyopathy without Inducing Obesity, Systemic Insulin Resistance, or Cardiac Steatosis.

Science.gov (United States)

Muthuramu, Ilayaraja; Amin, Ruhul; Postnov, Andrey; Mishra, Mudit; Jacobs, Frank; Gheysens, Olivier; Van Veldhoven, Paul P; De Geest, Bart

2017-07-18

Studies evaluating the effects of high-saturated fat diets on cardiac function are most often confounded by diet-induced obesity and by systemic insulin resistance. We evaluated whether coconut oil, containing C12:0 and C14:0 as main fatty acids, aggravates pressure overload-induced cardiomyopathy induced by transverse aortic constriction (TAC) in C57BL/6 mice. Mortality rate after TAC was higher ( p coconut oil diet-fed mice than in standard chow-fed mice (hazard ratio 2.32, 95% confidence interval 1.16 to 4.64) during eight weeks of follow-up. The effects of coconut oil on cardiac remodeling occurred in the absence of weight gain and of systemic insulin resistance. Wet lung weight was 1.76-fold ( p coconut oil mice than in standard chow mice. Myocardial capillary density ( p coconut oil mice than in standard chow mice. Myocardial glucose uptake was 1.86-fold ( p coconut oil mice and was accompanied by higher myocardial pyruvate dehydrogenase levels and higher acetyl-CoA carboxylase levels. The coconut oil diet increased oxidative stress. Myocardial triglycerides and free fatty acids were lower ( p coconut oil mice. In conclusion, coconut oil aggravates pressure overload-induced cardiomyopathy.

Brief report: Contextual predictors of African American adolescents' ethnic-racial identity affirmation-belonging and resistance to peer pressure.

Science.gov (United States)

Derlan, Chelsea L; Umaña-Taylor, Adriana J

2015-06-01

The current study examined whether contextual factors (i.e., familial cultural socialization, percentage of same-ethnicity friends in high school, and neighborhood ethnic-racial composition) predicted ethnic-racial identity affirmation-belonging and, in turn, resistance to peer pressure to engage in problem behavior. Participants were 250 African American adolescents (M age = 15.57 years; SD = 1.22). Consistent with ecological theory, findings indicated that familial cultural socialization and percentage of same-ethnicity friends predicted greater ethnic-racial identity affirmation-belonging. Furthermore, consistent with notions from social identity theory, youth who reported higher ethnic-racial identity affirmation-belonging also reported greater resistance to peer pressure. Findings highlight the significance of the family and school context, as well as the importance of ethnic-racial identity affirmation-belonging, for African American youths' positive development. Copyright © 2015 The Foundation for Professionals in Services for Adolescents. Published by Elsevier Ltd. All rights reserved.

Differential effects of sporulation temperature on the high pressure resistance of Clostridium botulinum type E spores and the interconnection with sporulation medium cation contents.

Science.gov (United States)

Lenz, Christian A; Vogel, Rudi F

2015-04-01

High pressure thermal (HPT) processing can be used to improve traditional preservation methods and increase food safety and durability, whereas quality related characteristics can be largely maintained. Clostridium (C.) botulinum type E is a non-proteolytic, psychrotrophic, toxin-producing spore former, commonly associated with aquatic environments in temperate regions of the northern hemisphere. Sporulation in nature is likely to occur under varying conditions including temperature and nutrient availability, which might affect resistance properties of resulting spores. In our study, we determined the effect of sporulation temperature (13-38 °C) on the resistance of three Clostridium botulinum type E strains to differently intense HPT treatments (200 MPa at 40 and 80 °C, and 800 MPa at 40 and 80 °C). Furthermore, the effect of cations on sporulation temperature-mediated alterations in HHP resistance was investigated. Results indicate that low and high sporulation temperatures can increase and decrease sporal HPT resistance, respectively, in a treatment-dependent (pressure level, treatment temperature) manner, whereas the trends observed are largely unaffected by pressure dwells (1 s-10 min). Furthermore, results show that the cation content of the sporulation medium (Ca(2+), Mg(2+), Mn(2+)) marginally influences and partially counteracts effects on the HPT resistance of spores grown at low and elevated temperatures, respectively. This suggests that sporulation temperature and medium cations provoke changes in some common spore resistance structures. Sporulation conditions can markedly affect spore resistance properties and, thus, should be considered for the experimental setup of worst case studies aiming to evaluate the effectiveness of food processes in terms of the inactivation of C. botulinum type E spores. Copyright © 2014 Elsevier Ltd. All rights reserved.

The effect of high-pressure devitrification and densification on ballistic-penetration resistance of fused silica

Science.gov (United States)

Avuthu, Vasudeva Reddy

Despite the clear benefits offered by more advanced transparent materials, (e.g. transparent ceramics offer a very attractive combination of high stiffness and high hardness levels, highly-ductile transparent polymers provide superior fragment-containing capabilities, etc.), ballistic ceramic-glass like fused-silica remains an important constituent material in a majority of transparent impact-resistant structures (e.g. windshields and windows of military vehicles, portholes in ships, ground vehicles and spacecraft) used today. Among the main reasons for the wide-scale use of glass, the following three are most frequently cited: (i) glass-structure fabrication technologies enable the production of curved, large surface-area, transparent structures with thickness approaching several inches; (ii) relatively low material and manufacturing costs; and (iii) compositional modifications, chemical strengthening, and controlled crystallization have been demonstrated to be capable of significantly improving the ballistic properties of glass. In the present work, the potential of high-pressure devitrification and densification of fused-silica as a ballistic-resistance-enhancement mechanism is investigated computationally. In the first part of the present work, all-atom molecular-level computations are carried out to infer the dynamic response and material microstructure/topology changes of fused silica subjected to ballistic impact by a nanometer-sized hard projectile. The analysis was focused on the investigation of specific aspects of the dynamic response and of the microstructural changes such as the deformation of highly sheared and densified regions, and the conversion of amorphous fused silica to SiO2 crystalline allotropic modifications (in particular, alpha-quartz and stishovite). The microstructural changes in question were determined by carrying out a post-processing atom-coordination procedure. This procedure suggested the formation of high-density stishovite (and

Obese children and adolescents have elevated nighttime blood pressure independent of insulin resistance and arterial stiffness

DEFF Research Database (Denmark)

Hvidt, Kristian N; Olsen, Michael H; Holm, Jens-Christian

2014-01-01

BACKGROUND: Insulin resistance has been related to elevated blood pressure (BP) in obese children and may adversely affect the vasculature by arterial stiffening. The objective was to investigate whether daytime and nighttime BP were elevated and related to insulin resistance and arterial stiffness...... in obese children and adolescents. METHODS: Ninety-two obese patients aged 10-18 years were compared with 49 healthy control individuals. Insulin resistance was measured as the homeostatic assessment model (HOMA), and arterial stiffness was measured as carotid-femoral pulse wave velocity (cfPWV). RESULTS......: Mean ± SD daytime systolic BP (SBP) (obese: 125±8.3mm Hg; control: 121±10.1mm Hg; P = 0.03) and nighttime SBP (obese: 108±10.7mm Hg; control: 102±8.2mm Hg; P = 0.0001) were higher in the obese group when compared with the control group. No difference was found in daytime diastolic BP (DBP), whereas...

Tetracycline-resistant Escherichia coli strains are inherited from parents and persist in the infant's intestines in the absence of selective pressure.

Science.gov (United States)

Prelog, Martina; Grif, Katharina; Decristoforo, Cornelia; Würzner, Reinhard; Kiechl-Kohlendorfer, Ursula; Brunner, Andrea; Zimmerhackl, Lothar Bernd; Orth, Dorothea

2009-10-01

The study investigated tetracycline (TC), ampicillin (AMP), cefazolin (CEF), and trimethoprim (TMP) resistance in Escherichia coli (E. coli) in the feces of 21 infants up to 6 months of age and in their parents in the absence of selective antimicrobial pressure. Clonality of strains was assessed by pulsed-field gel electrophoresis. Three infants had resistant E. coli strains in their feces identical to the mothers' from week 1 on, which persisted over weeks. From week 2 on, in another four infants, persisting resistant E. coli were found, two of them identical to the mothers'. All of these persisting E. coli strains (except one family) showed at least resistance to TC. In infants, resistant E. coli strains inherited from their mothers tended to persist over months. Therefore, the persistence of resistant E. coli and their possible capacity to cause symptomatic infection or transfer its resistance genes to other bacteria deserves more attention.

Carbon nanotube temperature and pressure sensors

Energy Technology Data Exchange (ETDEWEB)

Ivanov, Ilia N.; Geohegan, David B.

2017-09-12

The present invention, in one embodiment, provides a method of measuring pressure or temperature using a sensor including a sensor element composed of a plurality of carbon nanotubes. In one example, the resistance of the plurality of carbon nanotubes is measured in response to the application of temperature or pressure. The changes in resistance are then recorded and correlated to temperature or pressure. In one embodiment, the present invention provides for independent measurement of pressure or temperature using the sensors disclosed herein.

Carbon nanotube temperature and pressure sensors

Science.gov (United States)

Ivanov, Ilia N; Geohegan, David Bruce

2013-10-29

The present invention, in one embodiment, provides a method of measuring pressure or temperature using a sensor including a sensor element composed of a plurality of carbon nanotubes. In one example, the resistance of the plurality of carbon nanotubes is measured in response to the application of temperature or pressure. The changes in resistance are then recorded and correlated to temperature or pressure. In one embodiment, the present invention provides for independent measurement of pressure or temperature using the sensors disclosed herein.

Temperature measurement in the liquid helium range at pressure

International Nuclear Information System (INIS)

Itskevich, E.S.; Krajdenov, V.F.

1978-01-01

The use of bronze and germanium resistance thermometers and the use of a (Au + 0.07 % Fe)-Cu thermocouple for temperature measurements from 1.5 to 4.2 K in the hydrostatic compression of up to 10 kbar are considered. To this aim, the thermometer resistance as a function of temperature and pressure is measured. It is revealed that pressure does not change the thermometric response of the bronze resistance thermometer but only shifts it to the region of lower temperatures. The identical investigations of the germanium resistance thermometer shows that strong temperature dependence and the shift of its thermometric response under the influence of pressure make the use of germanium resistance thermometers in high-pressure chambers very inconvenient. The results of the analysis of the (Au + 0.07 % Fe) - Cu thermocouple shows that with a 2 per cent accuracy the thermocouple Seebeck coefficient does not depend on pressure. It permits to use this thermocouple for temperature measurements at high pressures

Assessing Collagen and Elastin Pressure-dependent Microarchitectures in Live, Human Resistance Arteries by Label-free Fluorescence Microscopy

DEFF Research Database (Denmark)

Bloksgaard, Maria; Thorsted, Bjarne; Brewer, Jonathan R

2018-01-01

The pathogenic contribution of resistance artery remodeling is documented in essential hypertension, diabetes and the metabolic syndrome. Investigations and development of microstructurally motivated mathematical models for understanding the mechanical properties of human resistance arteries...... in health and disease have the potential to aid understanding how disease and medical treatments affect the human microcirculation. To develop these mathematical models, it is essential to decipher the relationship between the mechanical and microarchitectural properties of the microvascular wall...... of interest. Image analyses are described for quantifying i) pressure-induced changes in internal elastic lamina branching angles and adventitial collagen straightness using Fiji and ii) collagen and elastin volume densities determined using Ilastik software. Preferably all mechanical and imaging measurements...

Hydraulic resistance of biofilms

KAUST Repository

Dreszer, C.; Vrouwenvelder, Johannes S.; Paulitsch-Fuchs, Astrid H.; Zwijnenburg, Arie; Kruithof, Joop C.; Flemming, Hans Curt

2013-01-01

resistance is very low compared to the expected biofilm resistance and, thus, biofilm resistance can be determined accurately. Transmembrane pressure drop was monitored. As biofilm parameters, thickness, total cell number, TOC, and extracellular polymeric

Resisting Pressure from Peers to Engage in Sexual Behavior: What Communication Strategies Do Early Adolescent Latino Girls Use?

Science.gov (United States)

Norris, Anne E.; Pettigrew, Jonathan; Miller-Day, Michelle; Hecht, Michael L.; Hutchison, Janet; Campoe, Kristi

2015-01-01

A content analysis of early adolescent X-bar = 12.02 years) Latino girls' (n = 44) responses to open-ended questions embedded in an electronic survey was conducted to explore strategies girls may use to resist peer pressure with respect to sexual behavior. Analysis yielded 341 codable response units, 74% of which were consistent with the REAL…

High hydrostatic pressure effects on Listeria monocytogenes and L. innocua: Evidence for variability in inactivation behaviour and in resistance to pediocin bacHA-6111-2.

Science.gov (United States)

Bruschi, Carolina; Komora, Norton; Castro, Sónia Marília; Saraiva, Jorge; Ferreira, Vânia Borges; Teixeira, Paula

2017-06-01

The effect of high hydrostatic pressure (HHP) on the survival of 14 strains of Listeria monocytogenes from food or clinical origins, selected to represent different pheno and genotypes, was evaluated. Stationary phase cells were submitted to 300, 400 and 500 MPa at 10 °C, for 5 min. A high variability in the resistance of L. monocytogenes to pressure was observed, and particularly two strains isolated from food were significantly more baroresistant than the rest. Strains of L. monocytogenes resistant to one or more antibiotics exhibited significantly higher levels of survival after the high pressure treatment at 400 MPa. No correlation was found between strains' origin or thermal tolerance and resistance to HHP. The suitability of two strains of L. innocua as surrogates of L. monocytogenes, was also investigated. These exhibited significantly higher sensitivities to HHP than observed for some L. monocytogenes. The antimicrobial effect of the antilisterial bacteriocin (bacHA-6111-2) increased after L. monocytogenes cells had been exposed to pressure. The data obtained underlines the importance of strain selection for studies aiming to evaluate HHP efficacy to ensure safety of HHP-treated foods. Copyright © 2017 Elsevier Ltd. All rights reserved.

RIMS (real-time imprint monitoring by scattering of light) study of pressure, temperature and resist effects on nanoimprint lithography

International Nuclear Information System (INIS)

Yu Zhaoning; Gao He; Chou, Stephen Y

2007-01-01

To optimize nanoimprint lithography (NIL), it is essential to be able to characterize and control the NIL process in situ and in real time. Recently we have developed a real-time imprint monitoring by the scattering-of-light (RIMS) approach, which allows us to detect the degree of resist deformation and the duration of resist penetration by a mould during the imprint process in real time. In this paper we report the performances of RIMS under a broad range of working conditions. RIMS data shows that the resist penetration is facilitated by increasing processing temperature, pressure and the resist film thickness; a prolonged pre-NIL resist baking step, on the other hand, has the effect of slowing it down. Our results provide further demonstration of the effectiveness of this method under different working conditions. RIMS measurements show not only how long an imprint takes to complete, but also how an imprint progresses with time and how it is affected by differences in processing parameters. These measurements provide information crucial for a better understanding and process optimization in NIL

Resistant and Refractory Hypertension: Antihypertensive Treatment Resistance vs Treatment Failure

Science.gov (United States)

Siddiqui, Mohammed; Dudenbostel, Tanja; Calhoun, David A.

2017-01-01

Resistant or difficult to treat hypertension is defined as high blood pressure that remains uncontrolled with 3 or more different antihypertensive medications, including a diuretic. Recent definitions also include controlled blood pressure with use of 4 or more medications as also being resistant to treatment. Recently, refractory hypertension, an extreme phenotype of antihypertensive treatment failure has been defined as hypertension uncontrolled with use of 5 or more antihypertensive agents, including a long-acting thiazide diuretic and a mineralocorticoid receptor antagonist. Patients with resistant vs refractory hypertension share similar characteristics and comorbidities, including obesity, African American race, female sex, diabetes, coronary heart disease, chronic kidney disease, and obstructive sleep apnea. Patients with refractory vs resistant hypertension tend to be younger and are more likely to have been diagnosed with congestive heart failure. Refractory hypertension might also differ from resistant hypertension in terms of underlying cause. Preliminary evidence suggests that refractory hypertension is more likely to be neurogenic in etiology (ie, heightened sympathetic tone), vs a volume-dependent hypertension that is more characteristic of resistant hypertension in general. PMID:26514749

Enhanced corrosion resistance and hemocompatibility of biomedical NiTi alloy by atmospheric-pressure plasma polymerized fluorine-rich coating

Energy Technology Data Exchange (ETDEWEB)

Li, Penghui; Li, Limin [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong (China); Wang, Wenhao [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong (China); Division of Spine Surgery, Department of Orthopaedics and Traumatology, Pokfulam, Hong Kong (China); Jin, Weihong [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong (China); Liu, Xiangmei [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong (China); Ministry of Education Key Laboratory for the Green Preparation and Application of Functional Materials, Hubei University, Wuhan, Hubei 430062 (China); Yeung, Kelvin W.K. [Division of Spine Surgery, Department of Orthopaedics and Traumatology, Pokfulam, Hong Kong (China); Chu, Paul K., E-mail: paul.chu@cityu.edu.hk [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong (China)

2014-04-01

Highlights: • Fluoropolymer is deposited on NiTi alloy via atmospheric-pressure plasma polymerization. • The corrosion resistance of NiTi alloy in SBF and DMEM is evidently improved. • The adsorption ratio of albumin to fibrinogen is increased on the coated surface. • The reduced platelet adhesion number indicates better in vitro hemocompatibility. - Abstract: To improve the corrosion resistance and hemocompatibility of biomedical NiTi alloy, hydrophobic polymer coatings are deposited by plasma polymerization in the presence of a fluorine-containing precursor using an atmospheric-pressure plasma jet. This process takes place at a low temperature in air and can be used to deposit fluoropolymer films using organic compounds that cannot be achieved by conventional polymerization techniques. The composition and chemical states of the polymer coatings are characterized by fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). The corrosion behavior of the coated and bare NiTi samples is assessed and compared by polarization tests and electrochemical impedance spectroscopy (EIS) in physiological solutions including simulated body fluids (SBF) and Dulbecco's Modified Eagle's medium (DMEM). The corrosion resistance of the coated NiTi alloy is evidently improved. Protein adsorption and platelet adhesion tests reveal that the adsorption ratio of albumin to fibrinogen is increased and the number of adherent platelets on the coating is greatly reduced. The plasma polymerized coating renders NiTi better in vitro hemocompatibility and is promising as a protective and hemocompatible coating on cardiovascular implants.

Genetic Diversity and Selective Pressure in Hepatitis C Virus Genotypes 1-6: Significance for Direct-Acting Antiviral Treatment and Drug Resistance.

Science.gov (United States)

Cuypers, Lize; Li, Guangdi; Libin, Pieter; Piampongsant, Supinya; Vandamme, Anne-Mieke; Theys, Kristof

2015-09-16

Treatment with pan-genotypic direct-acting antivirals, targeting different viral proteins, is the best option for clearing hepatitis C virus (HCV) infection in chronically infected patients. However, the diversity of the HCV genome is a major obstacle for the development of antiviral drugs, vaccines, and genotyping assays. In this large-scale analysis, genome-wide diversity and selective pressure was mapped, focusing on positions important for treatment, drug resistance, and resistance testing. A dataset of 1415 full-genome sequences, including genotypes 1-6 from the Los Alamos database, was analyzed. In 44% of all full-genome positions, the consensus amino acid was different for at least one genotype. Focusing on positions sharing the same consensus amino acid in all genotypes revealed that only 15% was defined as pan-genotypic highly conserved (≥99% amino acid identity) and an additional 24% as pan-genotypic conserved (≥95%). Despite its large genetic diversity, across all genotypes, codon positions were rarely identified to be positively selected (0.23%-0.46%) and predominantly found to be under negative selective pressure, suggesting mainly neutral evolution. For NS3, NS5A, and NS5B, respectively, 40% (6/15), 33% (3/9), and 14% (2/14) of the resistance-related positions harbored as consensus the amino acid variant related to resistance, potentially impeding treatment. For example, the NS3 variant 80K, conferring resistance to simeprevir used for treatment of HCV1 infected patients, was present in 39.3% of the HCV1a strains and 0.25% of HCV1b strains. Both NS5A variants 28M and 30S, known to be associated with resistance to the pan-genotypic drug daclatasvir, were found in a significant proportion of HCV4 strains (10.7%). NS5B variant 556G, known to confer resistance to non-nucleoside inhibitor dasabuvir, was observed in 8.4% of the HCV1b strains. Given the large HCV genetic diversity, sequencing efforts for resistance testing purposes may need to be

The mathematics of random mutation and natural selection for multiple simultaneous selection pressures and the evolution of antimicrobial drug resistance.

Science.gov (United States)

Kleinman, Alan

2016-12-20

The random mutation and natural selection phenomenon act in a mathematically predictable behavior, which when understood leads to approaches to reduce and prevent the failure of the use of these selection pressures when treating infections and cancers. The underlying principle to impair the random mutation and natural selection phenomenon is to use combination therapy, which forces the population to evolve to multiple selection pressures simultaneously that invoke the multiplication rule of probabilities simultaneously as well. Recently, it has been seen that combination therapy for the treatment of malaria has failed to prevent the emergence of drug-resistant variants. Using this empirical example and the principles of probability theory, the derivation of the equations describing this treatment failure is carried out. These equations give guidance as to how to use combination therapy for the treatment of cancers and infectious diseases and prevent the emergence of drug resistance. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Probabilistic modeling of material resistance to crack initiation due to hydrided region overloads in CANDU Zr-2.5%Nb pressure tubes

International Nuclear Information System (INIS)

Gutkin, L.; Scarth, D.A.

2014-01-01

Zr-2.5%Nb pressure tubes in CANDU nuclear reactors are susceptible to hydride-assisted cracking at the locations of stress concentration, such as in-service flaws. Probabilistic methodology is being developed to evaluate such flaws for crack initiation due to hydrided region overloads, which occur when the applied stress acting on a flaw with an existing hydrided region at its tip exceeds the stress at which the hydrided region is formed. As part of this development, probabilistic modeling of pressure tube material resistance to overload crack initiation has been performed on the basis of a set of test data specifically designed to study the effects of non-ratcheting hydride formation conditions and load reduction prior to hydride formation. In the modeling framework, the overload resistance is represented as a power-law function of the material resistance to initiation of delayed hydride cracking under constant loading, where both the overload crack initiation coefficient and the overload crack initiation exponent vary with the flaw geometry. In addition, the overload crack initiation coefficient varies with the extent of load reduction prior to hydride formation as well as the number of non-ratcheting hydride formation thermal cycles. (author)

Probabilistic modeling of material resistance to crack initiation due to hydrided region overloads in CANDU Zr-2.5%Nb pressure tubes

Energy Technology Data Exchange (ETDEWEB)

Gutkin, L.; Scarth, D.A. [Kinectrics Inc., Toronto, ON (Canada)

2014-07-01

Zr-2.5%Nb pressure tubes in CANDU nuclear reactors are susceptible to hydride-assisted cracking at the locations of stress concentration, such as in-service flaws. Probabilistic methodology is being developed to evaluate such flaws for crack initiation due to hydrided region overloads, which occur when the applied stress acting on a flaw with an existing hydrided region at its tip exceeds the stress at which the hydrided region is formed. As part of this development, probabilistic modeling of pressure tube material resistance to overload crack initiation has been performed on the basis of a set of test data specifically designed to study the effects of non-ratcheting hydride formation conditions and load reduction prior to hydride formation. In the modeling framework, the overload resistance is represented as a power-law function of the material resistance to initiation of delayed hydride cracking under constant loading, where both the overload crack initiation coefficient and the overload crack initiation exponent vary with the flaw geometry. In addition, the overload crack initiation coefficient varies with the extent of load reduction prior to hydride formation as well as the number of non-ratcheting hydride formation thermal cycles. (author)

Resistant Hypertension and Obstructive Sleep Apnea

Directory of Open Access Journals (Sweden)

Akram Khan

2013-01-01

Full Text Available Hypertension (HTN is a modifiable, highly prevalent risk factor for cardiovascular morbidity and renal dysfunction worldwide. In the United States, HTN affects one in three adults, contributes to one out of every seven deaths and to nearly half of all cardiovascular disease-related deaths. HTN is considered resistant when the blood pressure remains above goal despite lifestyle modification and administration of three antihypertensive agents of different classes including a diuretic. Large population-based studies have suggested that obstructive sleep apnea (OSA is a risk factor for resistant HTN. The mechanism proposed is a pattern of intermittent hypoxia associated with hyperaldosteronism, increased sympathetic tone, endothelial dysfunction, and inflammation. In this review we discuss the association between OSA and resistant HTN, the physiologic mechanisms linking OSA with resistant HTN, and the effect of continuous positive airway pressure therapy (CPAP on blood pressure in patients with resistant HTN. While the reduction in blood pressure with CPAP is usually modest in patients with OSA, a decrease of only a few mmHg in blood pressure can significantly reduce cardiovascular risk. Patients presenting to a center specializing in management of hypertension should be screened and treated for OSA as a potentially modifiable risk factor.

Transition from resistive ballooning to neoclassical magnetohydrodynamic pressure-gradient-driven instability

International Nuclear Information System (INIS)

Spong, D.A.; Shaing, K.C.; Carreras, B.A.; Charlton, L.A.; Callen, J.D.; Garcia, L.

1988-10-01

The linearized neoclassical magnetohydrodynamic equations, including perturbed neoclassical flows and currents, have been solved for parameter regimes where the neoclassical pressure-gradient-driven instability becomes important. This instability is driven by the fluctuating bootstrap current term in Ohm's law. It begins to dominate the conventional resistive ballooning mode in the banana-plateau collisionality regime [μ/sub e//ν/sub e/ /approximately/ √ε/(1 + ν/sub *e/) > ε 2 ] and is characterized by a larger radial mode width and higher growth rate. The neoclassical instability persists in the absence of the usual magnetic field curvature drive and is not significantly affected by compressibility. Scalings with respect to β, n (toroidal mode number), and μ (neoclassical viscosity) are examined using a large-aspect-ratio, three-dimensional initial-value code that solves linearized equations for the magnetic flux, fluid vorticity, density, and parallel ion flow velocity in axisymmetric toroidal geometry. 13 refs., 10 figs

Combined resistive and laser heating technique for in situ radial X-ray diffraction in the diamond anvil cell at high pressure and temperature

Energy Technology Data Exchange (ETDEWEB)

Miyagi, Lowell [Department of Geology and Geophysics, University of Utah, Salt Lake City, Utah 84112 (United States); Department of Earth Sciences, Montana State University, Bozeman, Montana 59717 (United States); Kanitpanyacharoen, Waruntorn; Kaercher, Pamela; Wenk, Hans-Rudolf; Alarcon, Eloisa Zepeda [Department of Earth and Planetary Science, University of California, Berkeley, California 94720 (United States); Raju, Selva Vennila [Advanced Light Source, Lawrence Berkeley Laboratory, Berkeley, California 94720 (United States); HiPSEC, Department of Physics, University of Nevada, Las Vegas, Nevada 89154 (United States); Knight, Jason; MacDowell, Alastair [Advanced Light Source, Lawrence Berkeley Laboratory, Berkeley, California 94720 (United States); Williams, Quentin [Department of Earth and Planetary Science, University of California, Santa Cruz, California 95064 (United States)

2013-02-15

To extend the range of high-temperature, high-pressure studies within the diamond anvil cell, a Liermann-type diamond anvil cell with radial diffraction geometry (rDAC) was redesigned and developed for synchrotron X-ray diffraction experiments at beamline 12.2.2 of the Advanced Light Source. The rDAC, equipped with graphite heating arrays, allows simultaneous resistive and laser heating while the material is subjected to high pressure. The goals are both to extend the temperature range of external (resistive) heating and to produce environments with lower temperature gradients in a simultaneously resistive- and laser-heated rDAC. Three different geomaterials were used as pilot samples to calibrate and optimize conditions for combined resistive and laser heating. For example, in Run1, FeO was loaded in a boron-mica gasket and compressed to 11 GPa then gradually resistively heated to 1007 K (1073 K at the diamond side). The laser heating was further applied to FeO to raise temperature to 2273 K. In Run2, Fe-Ni alloy was compressed to 18 GPa and resistively heated to 1785 K (1973 K at the diamond side). The combined resistive and laser heating was successfully performed again on (Mg{sub 0.9}Fe{sub 0.1})O in Run3. In this instance, the sample was loaded in a boron-kapton gasket, compressed to 29 GPa, resistive-heated up to 1007 K (1073 K at the diamond side), and further simultaneously laser-heated to achieve a temperature in excess of 2273 K at the sample position. Diffraction patterns obtained from the experiments were deconvoluted using the Rietveld method and quantified for lattice preferred orientation of each material under extreme conditions and during phase transformation.

Resistant Hypertension.

Science.gov (United States)

Doroszko, Adrian; Janus, Agnieszka; Szahidewicz-Krupska, Ewa; Mazur, Grzegorz; Derkacz, Arkadiusz

2016-01-01

Resistant hypertension is a severe medical condition which is estimated to appear in 9-18% of hypertensive patients. Due to higher cardiovascular risk, this disorder requires special diagnosis and treatment. The heterogeneous etiology, risk factors and comorbidities of resistant hypertension stand in need of sophisticated evaluation to confirm the diagnosis and select the best therapeutic options, which should consider lifestyle modifications as well as pharmacological and interventional treatment. After having excluded pseudohypertension, inappropriate blood pressure measurement and control as well as the white coat effect, suspicion of resistant hypertension requires an analysis of drugs which the hypertensive patient is treated with. According to one definition - ineffective treatment with 3 or more antihypertensive drugs including diuretics makes it possible to diagnose resistant hypertension. A multidrug therapy including angiotensin - converting enzyme inhibitors, angiotensin II receptor blockers, beta blockers, diuretics, long-acting calcium channel blockers and mineralocorticoid receptor antagonists has been demonstrated to be effective in resistant hypertension treatment. Nevertheless, optional, innovative therapies, e.g. a renal denervation or baroreflex activation, may create a novel pathway of blood pressure lowering procedures. The right diagnosis of this disease needs to eliminate the secondary causes of resistant hypertension e.g. obstructive sleep apnea, atherosclerosis and renal or hormonal disorders. This paper briefly summarizes the identification of the causes of resistant hypertension and therapeutic strategies, which may contribute to the proper diagnosis and an improvement of the long term management of resistant hypertension.

The European iNPH Multicentre Study on the predictive values of resistance to CSF outflow and the CSF Tap Test in patients with idiopathic normal pressure hydrocephalus

DEFF Research Database (Denmark)

Wikkelsø, Carsten; Hellström, Per; Klinge, Petra Margarete

2013-01-01

The objective was to determine the sensitivity, specificity, and positive and negative predictive values of the CSF Tap Test (CSF TT) and resistance to CSF outflow (Rout) for the outcome of shunting in a sample of patients with idiopathic normal pressure hydrocephalus (iNPH).......The objective was to determine the sensitivity, specificity, and positive and negative predictive values of the CSF Tap Test (CSF TT) and resistance to CSF outflow (Rout) for the outcome of shunting in a sample of patients with idiopathic normal pressure hydrocephalus (iNPH)....

Study on Temperature and Synthetic Compensation of Piezo-Resistive Differential Pressure Sensors by Coupled Simulated Annealing and Simplex Optimized Kernel Extreme Learning Machine.

Science.gov (United States)

Li, Ji; Hu, Guoqing; Zhou, Yonghong; Zou, Chong; Peng, Wei; Alam Sm, Jahangir

2017-04-19

As a high performance-cost ratio solution for differential pressure measurement, piezo-resistive differential pressure sensors are widely used in engineering processes. However, their performance is severely affected by the environmental temperature and the static pressure applied to them. In order to modify the non-linear measuring characteristics of the piezo-resistive differential pressure sensor, compensation actions should synthetically consider these two aspects. Advantages such as nonlinear approximation capability, highly desirable generalization ability and computational efficiency make the kernel extreme learning machine (KELM) a practical approach for this critical task. Since the KELM model is intrinsically sensitive to the regularization parameter and the kernel parameter, a searching scheme combining the coupled simulated annealing (CSA) algorithm and the Nelder-Mead simplex algorithm is adopted to find an optimal KLEM parameter set. A calibration experiment at different working pressure levels was conducted within the temperature range to assess the proposed method. In comparison with other compensation models such as the back-propagation neural network (BP), radius basis neural network (RBF), particle swarm optimization optimized support vector machine (PSO-SVM), particle swarm optimization optimized least squares support vector machine (PSO-LSSVM) and extreme learning machine (ELM), the compensation results show that the presented compensation algorithm exhibits a more satisfactory performance with respect to temperature compensation and synthetic compensation problems.

Resistant hypertension.

Science.gov (United States)

Wei, Fang-Fei; Zhang, Zhen-Yu; Huang, Qi-Fang; Yang, Wen-Yi; Staessen, Jan A

2018-06-15

The publication of the first non-randomised proof-of-concept trial of renal denervation as a treatment modality in treatment-resistant hypertension set the stage for a search for novel devices with the expectation that technology would reduce the burden of hypertension by reducing or eliminating the costly and lifelong use of blood pressure lowering medications. As we demonstrate in this review, this idea so attractive to manufacturers and invasive cardiologists and radiologists overlooked decades of careful pathophysiological research in a disease, which still remains enigmatic but remains the major cause of cardiovascular mortality worldwide. To make our point, we first reviewed the prevalence and risks associated with treatment-resistant hypertension. Next, we highlighted the key points required for the diagnosis of treatment-resistant hypertension, including the recording of the ambulatory blood pressure and the assessment of adherence to medication. Finally, we summarised new insights in the management of treatment-resistant hypertension by medication and devices and in the future research. Throughout our review, we focused on new evidence became available since 2013. Our conclusion is that optimising medical treatment based on simple algorithms remains the state of the art in treatment-resistant hypertension.

Evaluation of the a.c. potential drop method to determine J-crack resistance curves for a pressure vessel steel

International Nuclear Information System (INIS)

Gibson, G.P.

1989-01-01

An evaluation has been carried out of the a.c. potential drop technique for determining J-crack growth resistance curves for a pressure vessel steel. The technique involves passing an alternating current through the specimen and relating the changes in the potential drop across the crack mouth to changes in crack length occuring during the test. The factors investigated were the current and voltage probe positions, the a.c. frequency and the test temperature. In addition, by altering the heat treatment of the material, J-crack resistance curves were obtained under both contained and non-contained yielding conditions. In all situations, accurate J-R curves could be determined. (author)

Pressure Sensitive Device Using Conductive and Porous Structures

International Nuclear Information System (INIS)

So, Hye-Mi; Chang, Won Seok; Park, Cheolmin

2014-01-01

Porous conductors are known to demonstrate excellent electrical, mechanical, and chemical resistance. These porous conductors demonstrated potential applications in various fields such as electrodes for supercapacitors, flexible heaters, catalytic electrodes, and sorbents. In this study, we described a pressure sensitive device using conductive and porous sponges. With an extremely simple “dipping and drying” process using a single-walled carbon nanotube (SWCNT) solution, we produced conductive sponges with sheet resistance of < 30 kΩ/sq. These carbon nanotube sponges can be deformed into any shape elastically and repeatedly compressed to large strains without collapse. The pressure sensors developed from these sponges demonstrated high resistance change under pressure of up to a half of their initial resistance

Pressure Sensitive Device Using Conductive and Porous Structures

Energy Technology Data Exchange (ETDEWEB)

So, Hye-Mi; Chang, Won Seok [Korea Institute of Machinery and Materials, Daejeon (Korea, Republic of); Park, Cheolmin [University of Science and Technology, Daejeon (Korea, Republic of)

2014-07-15

Porous conductors are known to demonstrate excellent electrical, mechanical, and chemical resistance. These porous conductors demonstrated potential applications in various fields such as electrodes for supercapacitors, flexible heaters, catalytic electrodes, and sorbents. In this study, we described a pressure sensitive device using conductive and porous sponges. With an extremely simple “dipping and drying” process using a single-walled carbon nanotube (SWCNT) solution, we produced conductive sponges with sheet resistance of < 30 kΩ/sq. These carbon nanotube sponges can be deformed into any shape elastically and repeatedly compressed to large strains without collapse. The pressure sensors developed from these sponges demonstrated high resistance change under pressure of up to a half of their initial resistance.

Pressure Dependence of the Electrical Resistivity in Polymer Polyaniline

Directory of Open Access Journals (Sweden)

Daihui Huang

2013-01-01

Full Text Available Polyaniline (PAN was prepared by using a technique of chemical synthesis to obtain the insulating emeraldine base form. And then PAN was doped with toluenesulfonic acid (TSA, HCl, or camphor sulfonic acid (CSA to protonate it into conducting salt form. The morphologies and electrical property of PAN under atmospheric pressure were investigated. Subsequently, the high pressure using a Bridgman anvil cell was applied on the doped PAN, and the effect of high pressure on the properties of doped PAN was analyzed. At normal pressure, the conductivity of PAN increases as the PH value increases. While at high pressures, the conductivity of PAN increases, and then it becomes independent of pressure. The results indicate that the conductivity of PAN is related to the presence of the polaron band, and the doped PAN under high pressure will be enhanced strongly in conductivity because of overlap of polaron band and π band. However, with the further increase of the applied pressure, scattering mechanisms of carriers limit the conductivity of PAN.

Silicon pressure transducers: a review

International Nuclear Information System (INIS)

Aceves M, M.; Sandoval I, F.

1994-01-01

We present a review of the pressure sensors, which use the silicon piezo resistive effect and micro machining technique. Typical pressure sensors, applications, design and other different structures are presented. (Author)

Pressure dependence of coherence-incoherence crossover behavior in KFe2As2 observed by resistivity and 75As-NMR/NQR

Science.gov (United States)

Wiecki, P.; Taufour, V.; Chung, D. Y.; Kanatzidis, M. G.; Bud'ko, S. L.; Canfield, P. C.; Furukawa, Y.

2018-02-01

We present the results of 75As nuclear magnetic resonance (NMR), nuclear quadrupole resonance (NQR), and resistivity measurements in KFe2As2 under pressure (p ). The temperature dependence of the NMR shift, nuclear spin-lattice relaxation time (T1), and resistivity show a crossover between a high-temperature incoherent, local-moment behavior and a low-temperature coherent behavior at a crossover temperature (T*). T* is found to increase monotonically with pressure, consistent with increasing hybridization between localized 3 d orbital-derived bands with the itinerant electron bands. No anomaly in T* is seen at the critical pressure pc=1.8 GPa where a change of slope of the superconducting (SC) transition temperature Tc(p ) has been observed. In contrast, Tc(p ) seems to correlate with antiferromagnetic spin fluctuations in the normal state as measured by the NQR 1 /T1 data, although such a correlation cannot be seen in the replacement effects of A in the A Fe2As2 (A =K , Rb, Cs) family. In the superconducting state, two T1 components are observed at low temperatures, suggesting the existence of two distinct local electronic environments. The temperature dependence of the short T1 s indicates a nearly gapless state below Tc. On the other hand, the temperature dependence of the long component 1 /T1 L implies a large reduction in the density of states at the Fermi level due to the SC gap formation. These results suggest a real-space modulation of the local SC gap structure in KFe2As2 under pressure.

Conduction mechanism in a novel oxadiazole derivative: effects of temperature and hydrostatic pressure

International Nuclear Information System (INIS)

Luo Jifeng; Han Yonghao; Tang Bencheng; Gao Chunxiao; Li Min; Zou Guangtian

2005-01-01

The quasi-four-probe resistivity measurement on the microcrystal of 1,4-bis[(4-heptyloxyphenyl)-1,3,4-oxadiazolyl]phenylene (OXD-3) is carried out under variable pressure and temperature conditions using a diamond anvil cell (DAC). Sample resistivity is calculated with a finite element analysis method. The temperature and pressure dependences of the resistivity of OXD-3 microcrystal are measured up to 150 0 C and 15 GPa, and the resistivity of OXD-3 decreases with increasing temperature, indicating that OXD-3 exhibits organic semiconductor transport property in the region of experimental pressure. With an increase of pressure, the resistivity of OXD-3 first increases and reaches a maximum at about 8 GPa, and then begins to decrease at high pressures. From the x-ray diffraction data in DAC under pressure, we can conclude that the anomaly of resistivity variation at 8 GPa results from the pressure-induced amorphism of OXD-3

Coconut Oil Aggravates Pressure Overload-Induced Cardiomyopathy without Inducing Obesity, Systemic Insulin Resistance, or Cardiac Steatosis

Directory of Open Access Journals (Sweden)

Ilayaraja Muthuramu

2017-07-01

Full Text Available Studies evaluating the effects of high-saturated fat diets on cardiac function are most often confounded by diet-induced obesity and by systemic insulin resistance. We evaluated whether coconut oil, containing C12:0 and C14:0 as main fatty acids, aggravates pressure overload-induced cardiomyopathy induced by transverse aortic constriction (TAC in C57BL/6 mice. Mortality rate after TAC was higher (p < 0.05 in 0.2% cholesterol 10% coconut oil diet-fed mice than in standard chow-fed mice (hazard ratio 2.32, 95% confidence interval 1.16 to 4.64 during eight weeks of follow-up. The effects of coconut oil on cardiac remodeling occurred in the absence of weight gain and of systemic insulin resistance. Wet lung weight was 1.76-fold (p < 0.01 higher in coconut oil mice than in standard chow mice. Myocardial capillary density (p < 0.001 was decreased, interstitial fibrosis was 1.88-fold (p < 0.001 higher, and systolic and diastolic function was worse in coconut oil mice than in standard chow mice. Myocardial glucose uptake was 1.86-fold (p < 0.001 higher in coconut oil mice and was accompanied by higher myocardial pyruvate dehydrogenase levels and higher acetyl-CoA carboxylase levels. The coconut oil diet increased oxidative stress. Myocardial triglycerides and free fatty acids were lower (p < 0.05 in coconut oil mice. In conclusion, coconut oil aggravates pressure overload-induced cardiomyopathy.

Clinical approach in treatment of resistant hypertension

Directory of Open Access Journals (Sweden)

Jennifer Frank

2009-07-01

Full Text Available Jennifer Frank, David SommerfeldUniversity of Wisconsin School of Medicine and Public Health, Department of Family Medicine, Appleton, WI, USAAbstract: Resistant hypertension, defined as failure to achieve target blood pressure despite the use of optimal or maximum doses of at least 3 agents, one of which is a diuretic, or requiring 4 or more medications to achieve blood pressure goal, is likely to affect up to 20% of all patients with hypertension. Apparent resistant hypertension may be caused by medication nonadherence, substances that either interfere with antihypertensive mediations or cause blood pressure elevation, and under- or inappropriate medication treatment. Certain patient characteristics are associated with the presence of resistant hypertension and include chronic kidney disease, diabetes, obesity, and presence of end-organ damage (microalbuminuria, retinopathy, left-ventricular hypertrophy. Secondary causes of resistant hypertension are not uncommon and include obstructive sleep apnea, chronic kidney disease, primary aldosteronism, renal artery stenosis, pheochromocytoma, and Cushing’s disease. Initial medication management usually includes adding or increasing the dose of a diuretic, which is effective in lowering the blood pressure of a large number of patients with resistant hypertension. Additional management options include maximizing lifestyle modification, combination therapy of antihypertensive agents depending on individual patient characteristics, adding less-commonly used fourth- or fifth-line antihypertensive agents, and referral to a hypertension specialist.Keywords: resistant hypertension, blood pressure, diuretic

Literature survey of heat transfer and hydraulic resistance of water, carbon dioxide, helium and other fluids at supercritical and near-critical pressures

Energy Technology Data Exchange (ETDEWEB)

Pioro, I.L.; Duffey, R.B

2003-04-01

This survey consists of 430 references, including 269 Russian publications and 161 Western publications devoted to the problems of heat transfer and hydraulic resistance of a fluid at near-critical and supercritical pressures. The objective of the literature survey is to compile and summarize findings in the area of heat transfer and hydraulic resistance at supercritical pressures for various fluids for the last fifty years published in the open Russian and Western literature. The analysis of the publications showed that the majority of the papers were devoted to the heat transfer of fluids at near-critical and supercritical pressures flowing inside a circular tube. Three major working fluids are involved: water, carbon dioxide, and helium. The main objective of these studies was the development and design of supercritical steam generators for power stations (utilizing water as a working fluid) in the 1950s, 1960s, and 1970s. Carbon dioxide was usually used as the modeling fluid due to lower values of the critical parameters. Helium, and sometimes carbon dioxide, were considered as possible working fluids in some special designs of nuclear reactors. (author)

Superconductivity in CeRh2Si2 Under Pressure

International Nuclear Information System (INIS)

Araki, S.; Nakashima, M.; Settai, R.; Kobayashi, T.C.; Onuki, Y.

2003-01-01

We have studied the pressure-induced superconductivity in an antiferromagnet CeRh 2 Si 2 by measuring the electrical resistivity for a high-quality single crystal. The superconducting resistivity drop was observed around P c ∼eq 1.06 GPa, at which the Neel temperature becomes zero, namely in a pressure region from 0.97 to 1.20 GPa. The zero resistivity appears below 0.4 K between 1.03 to 1.08 GPa. The resistivity at low temperatures follows the Fermi liquid AT 2 relation in the whole pressure region, even at P c . The A value becomes a maximum around P c . (author)

Pressure induced anomalies in an As-Al-Te glass

International Nuclear Information System (INIS)

Mohan, Murali; Giridhar, A.; Mahadevan, Sudha

1995-01-01

The pressure and temperature dependences of the electrical resistance of As 34.4 Al 4 Te 61.6 and As 16.67 Al 16.67 Te 66.66 glasses have been investigated using an opposed anvil setup. The resistance of the glasses exhibit ∼ 10 6 fold decrease with increasing pressure up to 7 GPa at 300 K. This behaviour can be traced to the corresponding changes with pressure of the activation energy for electrical conduction, ΔE(p). The As 34.4 Al 4 Te 61.6 glass exhibits pressure induced anomalies at 2 GPa in the pressure variation of ΔE(p) and the pressure coefficient of electrical resistance. Such an anomaly is not seen for the As 16.67 Al 16.67 Te 66.66 glass. The anomalies point to a pressure induced morphological structural transformation in the As 34.4 Al 4 Te 61.6 glass. (author)

Influence of cerebrovascular resistance on the dynamic relationship between blood pressure and cerebral blood flow in humans.

Science.gov (United States)

Smirl, J D; Tzeng, Y C; Monteleone, B J; Ainslie, P N

2014-06-15

We examined the hypothesis that changes in the cerebrovascular resistance index (CVRi), independent of blood pressure (BP), will influence the dynamic relationship between BP and cerebral blood flow in humans. We altered CVRi with (via controlled hyperventilation) and without [via indomethacin (INDO, 1.2 mg/kg)] changes in PaCO2. Sixteen subjects (12 men, 27 ± 7 yr) were tested on two occasions (INDO and hypocapnia) separated by >48 h. Each test incorporated seated rest (5 min), followed by squat-stand maneuvers to increase BP variability and improve assessment of the pressure-flow dynamics using linear transfer function analysis (TFA). Beat-to-beat BP, middle cerebral artery velocity (MCAv), posterior cerebral artery velocity (PCAv), and end-tidal Pco2 were monitored. Dynamic pressure-flow relations were quantified using TFA between BP and MCAv/PCAv in the very low and low frequencies through the driven squat-stand maneuvers at 0.05 and 0.10 Hz. MCAv and PCAv reductions by INDO and hypocapnia were well matched, and CVRi was comparably elevated (P flow dynamics. These findings are consistent with the concept of CVRi being a key factor that should be considered in the correct interpretation of cerebral pressure-flow dynamics as indexed using TFA metrics. Copyright © 2014 the American Physiological Society.

Structural and electrical properties of TmTe under high pressure

International Nuclear Information System (INIS)

Tang, Jie; Matsumoto, Takehiko; Kosaka, Takayuki; Matsumura, Takeshi; Suzuki, Takashi; Mori, Nobuo

1997-01-01

Pressure-induced valence state of Tm ions in TmTe has been investigated by measurements of electrical resistivity in situ x-ray diffraction and magnetic susceptibility at high pressure. Below 2 GPa, the valence of Tm was confirmed to be 2 + from the results of compressibility and magnetic susceptibility. The pressure dependence of the electrical resistivity up to 2 GPa at room temperature showed an exponential decrease, indicating a linear closing of the energy gap at a rate of -1 meV/GPa. In the pressure range above 2 GPa where the energy gap disappeared, the valence transition from Tm 2+ to Tm 3+ was concluded from the pressure dependence of the lattice parameters. The electrical resistivity showing a logarithmic temperature dependence was reminiscent of Kondo effect. Above 6 GPa at which the pressure dependence of electrical resistivity abruptly decreased, the structure was confirmed to transform from the NaCl-type with Tm 3+ to a tetragonal structure. (author)

Responses to negative pressure surrounding the neck in anesthetized animals.

Science.gov (United States)

Wolin, A D; Strohl, K P; Acree, B N; Fouke, J M

1990-01-01

Continuous positive pressure applied at the nose has been shown to cause a decrease in upper airway resistance. The present study was designed to determine whether a similar positive transmural pressure gradient, generated by applying a negative pressure at the body surface around the neck, altered upper airway patency. Studies were performed in nine spontaneously breathing anesthetized supine dogs. Airflow was measured with a pneumotachograph mounted on an airtight muzzle placed over the nose and mouth of each animal. Upper airway pressure was measured as the differential pressure between the extrathoracic trachea and the inside of the muzzle. Upper airway resistance was monitored as an index of airway patency. Negative pressure (-2 to -20 cmH2O) was applied around the neck by using a cuirass extending from the jaw to the thorax. In each animal, increasingly negative pressures were transmitted to the airway wall in a progressive, although not linear, fashion. Decreasing the pressure produced a progressive fall in upper airway resistance, without causing a significant change in respiratory drive or respiratory timing. At -5 cmH2O pressure, there occurred a significant fall in upper airway resistance, comparable with the response of a single, intravenous injection of sodium cyanide (0.5-3.0 mg), a respiratory stimulant that produces substantial increases in respiratory drive. We conclude that upper airway resistance is influenced by the transmural pressure across the airway wall and that such a gradient can be accomplished by making the extraluminal pressure more negative.(ABSTRACT TRUNCATED AT 250 WORDS)

Pressure test method for reactor pressure vessel in construction field

International Nuclear Information System (INIS)

Takeda, Masakado; Ushiroda, Koichi; Miyahara, Ryohei; Takano, Hiroshi; Matsuura, Tadashi; Sato, Keiya.

1998-01-01

Plant constitutional parts as targets of both of a primary pressure test and a secondary pressure test are disposed in communication with a reactor pressure vessel, and a pressure of the primary pressure test is applied to the targets of both tests, so that the primary pressure test and the second pressure test are conducted together. Since the number of pressure tests can be reduced to promote construction, and the number of workers can also be reduced. A pressure exceeding the maximum pressure upon use is applied to the pressure vessel after disposing the incore structures, to continuously conduct the primary pressure test and the secondary pressure test joined together and an incore flowing test while closing the upper lid of the pressure vessel as it is in the construction field. The number of opening/closing of the upper lid upon conducting every test can be reduced, and since the pressure resistance test is conducted after arranging circumference conditions for the incore flowing test, the tests can be conducted collectively also in view of time. (N.H.)

Transposon characterization of vancomycin-resistant Enterococcus faecium (VREF) and dissemination of resistance associated with transferable plasmids

DEFF Research Database (Denmark)

Migura, Lourdes Garcia; Liebana, Ernesto; Jensen, Lars Bogø

2007-01-01

Objectives: VanA glycopeptide resistance has persisted on broiler farms in the UK despite the absence of the antimicrobial selective pressure, avoparcin. This study aimed to investigate the contribution of horizontal gene transfer of Tn 1546 versus clonal spread in the dissemination of the resist......Objectives: VanA glycopeptide resistance has persisted on broiler farms in the UK despite the absence of the antimicrobial selective pressure, avoparcin. This study aimed to investigate the contribution of horizontal gene transfer of Tn 1546 versus clonal spread in the dissemination...... plasmid replicons, associated with antimicrobial resistance on several unrelated farms. Conclusions: Horizontal transfer of vancomycin resistance may play a more important role in the persistence of antimicrobial resistance than clonal spread. The presence of different plasmid replicons, associated...... with antimicrobial resistance on several unrelated farms, illustrates the ability of these enterococci to acquire and disseminate mobile genetic elements within integrated livestock systems....

Dorsalis pedis arterial pressure is lower than noninvasive arm blood pressure in normotensive patients under sevoflurane anesthesia.

Science.gov (United States)

Chen, Yan; Wang, Enqin; Zhu, Yuan; Li, Yongshuai; Lu, Kaizhi

2016-02-01

It is widely known that blood pressure (BP) in the lower extremity is higher than in the upper extremity. However, whether this phenomenon remains the same during general anesthesia is still unclear. This study aims to investigate the difference between invasive dorsalis pedis artery (DPA) pressure and the most commonly used noninvasive arm pressure during sevoflurane anesthesia. A total of 50 normotensive Chinese patients were enrolled in this observational study. Invasive DPA pressure, noninvasive arm pressure, and systemic vascular resistance index were assessed simultaneously. BP data during the entire surgery were analyzed through a Bland-Altman plot for repeated measures. The concordance of BP variation in the DPA and the arm was analyzed using four-quadrant plots and linear regression. The time-dependent changes in BP and the systemic vascular resistance index were also evaluated. Data from 46 effective cases were analyzed. Bias (95% limits of agreement) was -7.40 mmHg (-20.36 to +5.57 mmHg) for mean blood pressure, +3.54 mmHg (-20.32 to +27.41 mmHg) for systolic blood pressure, and -10.20 mmHg (-23.66 to +3.26 mmHg) for diastolic blood pressure, respectively. The concordance of BP variation at the two measurement sites was clinically acceptable. DPA pressure and vascular resistance in the lower limb decreased gradually during surgery. DPA pressure tends to be lower than arm pressure under sevoflurane anesthesia, especially the mean blood pressure and the diastolic blood pressure. Hence, noninvasive arm BP monitoring is recommend to be retained when invasive BP is measured at the DPA, so as to allow clinicians to comprehensively evaluate the BP condition of the patients and make appropriate therapeutic decisions.

Estimation of contact resistance in proton exchange membrane fuel cells

Energy Technology Data Exchange (ETDEWEB)

Zhang, Lianhong; Liu, Ying; Song, Haimin; Wang, Shuxin [School of Mechanical Engineering, Tianjin University, 92 Weijin Road, Nankai District, Tianjin 300072 (China); Zhou, Yuanyuan; Hu, S. Jack [Department of Mechanical Engineering, The University of Michigan, Ann Arbor, MI 48109-2125 (United States)

2006-11-22

The contact resistance between the bipolar plate (BPP) and the gas diffusion layer (GDL) is an important factor contributing to the power loss in proton exchange membrane (PEM) fuel cells. At present there is still not a well-developed method to estimate such contact resistance. This paper proposes two effective methods for estimating the contact resistance between the BPP and the GDL based on an experimental contact resistance-pressure constitutive relation. The constitutive relation was obtained by experimentally measuring the contact resistance between the GDL and a flat plate of the same material and processing conditions as the BPP under stated contact pressure. In the first method, which was a simplified prediction, the contact area and contact pressure between the BPP and the GDL were analyzed with a simple geometrical relation and the contact resistance was obtained by the contact resistance-pressure constitutive relation. In the second method, the contact area and contact pressure between the BPP and GDL were analyzed using FEM and the contact resistance was computed for each contact element according to the constitutive relation. The total contact resistance was then calculated by considering all contact elements in parallel. The influence of load distribution on contact resistance was also investigated. Good agreement was demonstrated between experimental results and predictions by both methods. The simplified prediction method provides an efficient approach to estimating the contact resistance in PEM fuel cells. The proposed methods for estimating the contact resistance can be useful in modeling and optimizing the assembly process to improve the performance of PEM fuel cells. (author)

High pressure transport properties of Yb2Cu9

International Nuclear Information System (INIS)

Spendeler, L.; Jaccard, D.; Sierro, J.; Flouquet, J.

1992-01-01

The electrical resistivity (ρ) and the absolute thermopower (S) of high-purity Yb 2 Cu 9 have been measured between 1.2 and 300 K at pressures up to 17 kbar and in magnetic fields up to 6 T. At zero pressure the three measured samples show a Kondo peak in the resistivity at 17 K. Furthermore for one of them the resistivity rises below 5 K. Under pressure, the Kondo peak in ρ slowly moves towards lower temperatures indicating a decrease of the Kondo temperature T K , in good agreement with specific heat results. The increase of ρ below 5 K disappears completely for pressure lower than 1 kbar and the residual resistivity remains high. The thermopower S exhibits similar trends. Magnetic field dependences of both ρ and S are weak. No evidence of magnetic ordering has been detected up to 17.6 kbar

Endotracheal tube resistance and inertance in a model of mechanical ventilation of newborns and small infants—the impact of ventilator settings on tracheal pressure swings

International Nuclear Information System (INIS)

Hentschel, Roland; Buntzel, Julia; Guttmann, Josef; Schumann, Stefan

2011-01-01

Resistive properties of endotracheal tubes (ETTs) are particularly relevant in newborns and small infants who are generally ventilated through ETTs with a small inner diameter. The ventilation rate is also high and the inspiratory time (ti) is short. These conditions effectuate high airway flows with excessive flow acceleration, so airway resistance and inertance play an important role. We carried out a model study to investigate the impact of varying ETT size, lung compliance and ventilator settings, such as peak inspiratory pressure (PIP), positive end expiratory pressure (PEEP) and inspiratory time (ti) on the pressure–flow characteristics with respect to the resistive and inertive properties of the ETT. Pressure at the Y piece was compared to direct measurement of intratracheal pressure (P trach ) at the tip of the ETT, and pressure drop (ΔP ETT ) was calculated. Applying published tube coefficients (Rohrer's constants and inertance), P trach was calculated from ventilator readings and compared to measured P trach using the root-mean-square error. The most relevant for ΔP ETT was the ETT size, followed by (in descending order) PIP, compliance, ti and PEEP, with gas flow velocity being the principle in common for all these parameters. Depending on the ventilator settings ΔP ETT exceeded 8 mbar in the smallest 2.0 mm ETT. Consideration of inertance as an additional effect in this setting yielded a better agreement of calculated versus measured P trach than Rohrer's constants alone. We speculate that exact tracheal pressure tracings calculated from ventilator readings by applying Rohrer's equation and the inertance determination to small size ETTs would be helpful. As an integral part of ventilator software this would (1) allow an estimate of work of breathing and implementation of an automatic tube compensation, and (2) be important for gentle ventilation in respiratory care, especially of small infants, since it enables the physician to

Combined resistance and endurance exercise training improves arterial stiffness, blood pressure, and muscle strength in postmenopausal women.

Science.gov (United States)

Figueroa, Arturo; Park, Song Y; Seo, Dae Y; Sanchez-Gonzalez, Marcos A; Baek, Yeong H

2011-09-01

Menopause is associated with increased arterial stiffness and reduced muscle strength. Combined resistance (RE) and endurance (EE) exercise training can decrease brachial-ankle pulse wave velocity (baPWV), an index of arterial stiffness, in young men. We tested the hypothesis that combined circuit RE and EE training would improve baPWV, blood pressure (BP), and muscle strength in postmenopausal women. Twenty-four postmenopausal women (age 47-68 y) were randomly assigned to a "no exercise" control (n = 12) or to combined exercise training (EX; n = 12) group. The EX group performed concurrent circuit RE training followed by EE training at 60% of the predicted maximal heart rate (HR) 3 days per week. Brachial systolic BP, diastolic BP, mean arterial pressure, baPWV, HR, and dynamic and isometric muscle strength were measured before and after the 12-week study. Mean ± SE baPWV (-0.8 ± 0.2 meters/s), systolic BP (-6.0 ± 1.9 mm Hg), diastolic BP (-4.8 ± 1.7 mm Hg), HR (-4.0 ± 1.0 beats/min), and mean arterial pressure (-5.1 ± 1.6 mm Hg) decreased (P hypertension and frailty in postmenopausal women.

Cocoa reduces blood pressure and insulin resistance and improves endothelium-dependent vasodilation in hypertensives.

Science.gov (United States)

Grassi, Davide; Necozione, Stefano; Lippi, Cristina; Croce, Giuseppe; Valeri, Letizia; Pasqualetti, Paolo; Desideri, Giovambattista; Blumberg, Jeffrey B; Ferri, Claudio

2005-08-01

Consumption of flavanol-rich dark chocolate (DC) has been shown to decrease blood pressure (BP) and insulin resistance in healthy subjects, suggesting similar benefits in patients with essential hypertension (EH). Therefore, we tested the effect of DC on 24-hour ambulatory BP, flow-mediated dilation (FMD), and oral glucose tolerance tests (OGTTs) in patients with EH. After a 7-day chocolate-free run-in phase, 20 never-treated, grade I patients with EH (10 males; 43.7+/-7.8 years) were randomized to receive either 100 g per day DC (containing 88 mg flavanols) or 90 g per day flavanol-free white chocolate (WC) in an isocaloric manner for 15 days. After a second 7-day chocolate-free period, patients were crossed over to the other treatment. Noninvasive 24-hour ambulatory BP, FMD, OGTT, serum cholesterol, and markers of vascular inflammation were evaluated at the end of each treatment. The homeostasis model assessment of insulin resistance (HOMA-IR), quantitative insulin sensitivity check index (QUICKI), and insulin sensitivity index (ISI) were calculated from OGTT values. Ambulatory BP decreased after DC (24-hour systolic BP -11.9+/-7.7 mm Hg, Pbenefit if included as part of a healthy diet for patients with EH.

Thin film oxygen partial pressure sensor

Science.gov (United States)

Wortman, J. J.; Harrison, J. W.; Honbarrier, H. L.; Yen, J.

1972-01-01

The development is described of a laboratory model oxygen partial pressure sensor using a sputtered zinc oxide thin film. The film is operated at about 400 C through the use of a miniature silicon bar. Because of the unique resistance versus temperature relation of the silicon bar, control of the operational temperature is achieved by controlling the resistance. A circuit for accomplishing this is described. The response of sputtered zinc oxide films of various thicknesses to oxygen, nitrogen, argon, carbon dioxide, and water vapor caused a change in the film resistance. Over a large range, film conductance varied approximately as the square root of the oxygen partial pressure. The presence of water vapor in the gas stream caused a shift in the film conductance at a given oxygen partial pressure. A theoretical model is presented to explain the characteristic features of the zinc oxide response to oxygen.

Ambulatory blood pressure and adherence monitoring: diagnosing pseudoresistant hypertension.

Science.gov (United States)

Burnier, Michel; Wuerzner, Gregoire

2014-01-01

A small proportion of the treated hypertensive population consistently has a blood pressure greater than 140/90 mm Hg despite a triple therapy including a diuretic, a calcium channel blocker, and a blocker of the renin-angiotensin system. According to guidelines, these patients have so-called resistant hypertension. The prevalence of this clinical condition is higher in tertiary than primary care centers and often is associated with chronic kidney disease, diabetes, obesity, and sleep apnea syndrome. Exclusion of pseudoresistant hypertension using ambulatory or home blood pressure monitoring is a crucial step in the investigation of patients with resistant hypertension. Thus, among the multiple factors to consider when investigating patients with resistant hypertension, ambulatory blood pressure monitoring should be performed very early. Among other factors to consider, physicians should investigate patient adherence to therapy, assess the adequacy of treatment, exclude interfering factors, and, finally, look for secondary forms of hypertension. Poor adherence to therapy accounts for 30% to 50% of cases of resistance to therapy depending on the methodology used to diagnose adherence problems. This review discusses the clinical factors implicated in the pathogenesis of resistant hypertension with a particular emphasis on pseudoresistance, drug adherence, and the use of ambulatory blood pressure monitoring for the diagnosis and management of resistant hypertension.

Pressure-induced metal-insulator transition in spinel compound CuV2S4

International Nuclear Information System (INIS)

Okada, H.; Koyama, K.; Hedo, M.; Uwatoko, Y.; Watanabe, K.

2008-01-01

In order to investigate the pressure effect on electrical properties of CuV 2 S 4 , we performed the electrical resistivity measurements under high pressures up to 8 GPa for a high-quality polycrystalline sample. The charge density wave (CDW) transition temperatures increase with increasing pressure. The residual resistivity rapidly increases with increasing pressure over 4 GPa, and the temperature dependence of the electrical resistivity at 8 GPa exhibits a semiconducting behavior below about 150 K, indicating that a pressure-induced metal-insulator transition occurs in CuV 2 S 4 at 8 GPa

Magnesium based composites fabricated by low pressure infiltration

International Nuclear Information System (INIS)

Johansson, P.; Micski, A.; Savage, S.J.

1993-01-01

Magnesiumbased fiber composites have been produced by so called low pressure infiltration. The initial material consist of 'saffil' pre-forms and two magnesium alloys, Mg-9Al-1Zn and WE 54 (approximate composition Mg-5Y-1.5Nd-2(Tb,Er,Dy,Gd)-0.5Zr), and pure magnesium. The preforms consists of 10-30 vol% of short fibers linked together by SiO 2 or Al 2 O 3 . Three different routes have been tested in the search for a good low pressure infiltration method. The experiments cover corrosion testing in NaCl-solution, sliding wear, abrasion and erosion testing. Of the tested infiltration methods the best results were obtained in a resistance heated evacuable furnace, in which the metal was molted in a steel crucible and the preform was conveyed into the melt under protective atmosphere. The infiltration takes place at atmospheric pressure and the cooling is performed in a sealed tube in air. The microscopy studies shows that low pressure infiltrated composites contain considerable amounts of porosity in distinction from those fabricated by squeeze casting. The corrosion test has shown that in the tested environment the alloy WE 54 has good corrosion resistance while Mg-9Al-1Zn and pure magnesium show low corrosion resistance. The influence of fibres in the matrix seems to be very small. Both magnesium and the alloy Mg-9Al-1Zn show for two body abrasion an almost linear improvement of abrasion resistance with increased fiber content. Pure magnesium shows decreasing erosion resistance with increasing fibre content. The Mg-9Al-1Zn-alloy appears to show a maximum in erosion resistance at 10 vol% fibers. In sliding wear the materials show an optimum initial and steady state wear resistance at a fiber content of about 10%. In general Al 2 O 3 -binder gives better wear resistance than SiO 2 -binder. Tensile testing was performed on low pressure infiltrated and squeeze cast composites with WE 54 matrix. It shows that the low pressure infiltrated composites are inferior to those

Hydraulic resistance of biofilms

KAUST Repository

Dreszer, C.

2013-02-01

Biofilms may interfere with membrane performance in at least three ways: (i) increase of the transmembrane pressure drop, (ii) increase of feed channel (feed-concentrate) pressure drop, and (iii) increase of transmembrane passage. Given the relevance of biofouling, it is surprising how few data exist about the hydraulic resistance of biofilms that may affect the transmembrane pressure drop and membrane passage. In this study, biofilms were generated in a lab scale cross flow microfiltration system at two fluxes (20 and 100Lm-2h-1) and constant cross flow (0.1ms-1). As a nutrient source, acetate was added (1.0mgL-1 acetate C) besides a control without nutrient supply. A microfiltration (MF) membrane was chosen because the MF membrane resistance is very low compared to the expected biofilm resistance and, thus, biofilm resistance can be determined accurately. Transmembrane pressure drop was monitored. As biofilm parameters, thickness, total cell number, TOC, and extracellular polymeric substances (EPS) were determined, it was demonstrated that no internal membrane fouling occurred and that the fouling layer actually consisted of a grown biofilm and was not a filter cake of accumulated bacterial cells. At 20Lm-2h-1 flux with a nutrient dosage of 1mgL-1 acetate C, the resistance after 4 days reached a value of 6×1012m-1. At 100Lm-2h-1 flux under the same conditions, the resistance was 5×1013m-1. No correlation of biofilm resistance to biofilm thickness was found; Biofilms with similar thickness could have different resistance depending on the applied flux. The cell number in biofilms was between 4×107 and 5×108 cellscm-2. At this number, bacterial cells make up less than a half percent of the overall biofilm volume and therefore did not hamper the water flow through the biofilm significantly. A flux of 100Lm-2h-1 with nutrient supply caused higher cell numbers, more biomass, and higher biofilm resistance than a flux of 20Lm-2h-1. However, the biofilm thickness

Improvement of wheat for resistance to Russian Wheat Aphid

International Nuclear Information System (INIS)

Kinyua, M.; Malinga, J.N.; Wanyama, J.; Karanja, L.; Njau, P.; Leo, T.; Alomba, E.

2001-01-01

Breeding for resistance against Russian wheat aphid in Kenya is reported. Results of six of the lines were found to have high to moderate resistance to Russian wheat aphid. Popular lines were susceptible in the greenhouse when subjected to aphid pressure but showed moderate susceptibility when screened under field conditions, indicating that in years or location with low aphid pressure farmers may still get a crop. However in areas of high aphid pressure or bad years they may lose their crop. Consequently, developing resistant/torerant varieties is urgent

Improvement in All-Cause Mortality With Blood Pressure Control in a Group of US Veterans With Drug-Resistant Hypertension.

Science.gov (United States)

Fatemi, Omid; Goa, Cristobal; Faselis, Charles; Kokkinos, Peter; Papademetriou, Vasilios

2016-01-01

The current definition of drug-resistant hypertension includes patients with uncontrolled (URH) (taking ≥3 antihypertensive medications) and controlled hypertension (CRH; blood pressure [BP] ≤140/90 mm Hg) (taking ≥4 medications). The authors hypothesized that all-cause mortality is reduced when URH is controlled. Qualified patients followed at the Washington DC VA Medical Center were included. BPs were averaged for each year of follow-up. In 2006, among 2906 patients who met the criteria for drug-resistant hypertension, 628 had URH. During follow-up, 234 patients were controlled (group 1) and 394 patients remained uncontrolled (group 2). The mortality rate among patients with URH was 28% (110 of 394) and among patients with CRH was 13% (30 of 234), a 54% reduction (Phypertension markedly reduces all-cause mortality. © 2015 Wiley Periodicals, Inc.

Electrical resistivity of YbRh2Si2 and EuT2Ge2 (T=Co,Cu) at extreme conditions of pressure and temperature

International Nuclear Information System (INIS)

Dionicio, G.A.

2006-01-01

This investigation addresses the effect that pressure, p, and temperature, T, have on 4f states of the rare-earth elements in the isostructural YbRh 2 Si 2 , EuCo 2 Ge 2 , and EuCu 2 Ge 2 compounds. Upon applying pressure the volume of the unit cell reduces, enforcing either the enhancement of the hybridization of the 4f localized electrons with the ligand or a change in the valence state of the rare-earth ions. Here, we probe the effect of a pressure-induced lattice contraction on these system by means of electrical-resistivity measurements, ρ(T), from room temperature down to 100 mK. (orig.)

DEPENDENCE OF AIR SPRING PARAMETERS ON THROTTLE RESISTANCE

Directory of Open Access Journals (Sweden)

O. H. Reidemeister

2016-04-01

Full Text Available Purpose. In this paper it is necessary to conduct: 1 research and analyse the influence of throttle element pneumatic resistance on elastic and damping parameters of air spring; 2 to obtain the dependence of air spring parameters on throttle element pneumatic resistance value. Methodology. The work presents the elaborated model of the air spring as a dynamic system with three phase coordinates (cylinder pressure, auxiliary reservoir pressure, cylinder air mass. Stiffness and viscosity coefficients were determined on the basis of system response to harmonic kinematic disturbance. The data for the analysis are obtained by changing the capacity of the connecting element and the law of pressure variation between the reservoir and the cylinder. The viscosity coefficient is regarded as the viscosity ratio of the hydraulic damper, which for one oscillation cycle consumes the same energy as the air spring. The process of air condition change inside the cylinder (reservoir is considered to be adiabatic; the mass air flow through the connecting element depends on the pressure difference. Findings. We obtained the curves for spring viscosity and stiffness coefficients dependence on the throttle resistance at three different laws, linking airflow through the cylinder with the pressure difference in cylinder and reservoir. At both maximum and minimum limiting resistance values the spring viscosity tends to zero, reaching its peak in the mean resistance values. Stiffness increases monotonically with increasing resistance, tends to the limit corresponding to the absence of an auxiliary reservoir (at high resistance and the increase in cylinder volume by the reservoir volume (at low resistance. Originality.The designed scheme allows determining the optimal parameters of elastic and damping properties of the pneumatic system as function of the throttle element air resistance. Practical value.The ability to predict the parameters of elastic and damping properties

Multidrug-Resistant Candida

DEFF Research Database (Denmark)

Arendrup, Maiken Cavling; Patterson, Thomas F

2017-01-01

Invasive Candida infections remain an important cause of morbidity and mortality, especially in hospitalized and immunocompromised or critically ill patients. A limited number of antifungal agents from only a few drug classes are available to treat patients with these serious infections. Resistance...... can be either intrinsic or acquired. Resistance mechanisms are not exchanged between Candida; thus, acquired resistance either emerges in response to an antifungal selection pressure in the individual patient or, more rarely, occur due to horizontal transmission of resistant strains between patients....... Although multidrug resistance is uncommon, increasing reports of multidrug resistance to the azoles, echinocandins, and polyenes have occurred in several Candida species, most notably Candida glabrata and more recently Candida auris. Drivers are overall antifungal use, subtherapeutic drug levels at sites...

Leg intravenous pressure during head-up tilt.

NARCIS (Netherlands)

Groothuis, J.T.; Poelkens, F.; Wouters, C.W.; Kooijman, H.M.; Hopman, M.T.E.

2008-01-01

Leg vascular resistance is calculated as the arterial-venous pressure gradient divided by blood flow. During orthostatic challenges it is assumed that the hydrostatic pressure contributes equally to leg arterial, as well as to leg venous pressure. Because of venous valves, one may question whether,

Distinguishing HIV-1 drug resistance, accessory, and viral fitness mutations using conditional selection pressure analysis of treated versus untreated patient samples

Directory of Open Access Journals (Sweden)

Lee Christopher

2006-05-01

Full Text Available Abstract Background HIV can evolve drug resistance rapidly in response to new drug treatments, often through a combination of multiple mutations 123. It would be useful to develop automated analyses of HIV sequence polymorphism that are able to predict drug resistance mutations, and to distinguish different types of functional roles among such mutations, for example, those that directly cause drug resistance, versus those that play an accessory role. Detecting functional interactions between mutations is essential for this classification. We have adapted a well-known measure of evolutionary selection pressure (Ka/Ks and developed a conditional Ka/Ks approach to detect important interactions. Results We have applied this analysis to four independent HIV protease sequencing datasets: 50,000 clinical samples sequenced by Specialty Laboratories, Inc.; 1800 samples from patients treated with protease inhibitors; 2600 samples from untreated patients; 400 samples from untreated African patients. We have identified 428 mutation interactions in Specialty dataset with statistical significance and we were able to distinguish primary vs. accessory mutations for many well-studied examples. Amino acid interactions identified by conditional Ka/Ks matched 80 of 92 pair wise interactions found by a completely independent study of HIV protease (p-value for this match is significant: 10-70. Furthermore, Ka/Ks selection pressure results were highly reproducible among these independent datasets, both qualitatively and quantitatively, suggesting that they are detecting real drug-resistance and viral fitness mutations in the wild HIV-1 population. Conclusion Conditional Ka/Ks analysis can detect mutation interactions and distinguish primary vs. accessory mutations in HIV-1. Ka/Ks analysis of treated vs. untreated patient data can distinguish drug-resistance vs. viral fitness mutations. Verification of these results would require longitudinal studies. The result

Limiting the blood pressure response in young males during ...

African Journals Online (AJOL)

Studies have shown that resistance exercises are beneficial in the lowering of blood pressure. This is of great significance to hypertensive patients. Unfortunately the acute effect that resistance exercises have on blood pressure can be harmful. The seated single leg press was used in this study due to the availability of ...

High-pressure studies on nanocrystalline borderline Co1-xFexS2 (x = 0.4 and 0.5) using Mössbauer spectroscopic and electrical resistivity techniques up to 8 GPa

Science.gov (United States)

Chandra, Usha; Sharma, Pooja; Parthasarathy, G.

2016-12-01

Like bulk, Co1-xFexS2 nanoparticles also display an anomaly at x = 0.5. The borderline contiguous Co1-xFexS2 (x = 0.4 and 0.5) nanoparticles were synthesized with colloidal method and characterized for pyrite structure using various techniques, viz., X-ray diffraction, energy dispersive X-ray analysis (EDAX), S K-edge X-ray absorption near edge spectra, transmission electron microscopy (TEM) and Fourier transformed infra-red spectroscopy. The report presents the effect of high pressure on the borderline compositions using the Mössbauer spectroscopic and electrical resistivity techniques. Magnetic measurements on the system showed drastic lowering of Tc due to nanosize of the particles. With increased pressure, quadrupole splitting showed an expected trend of increase to attain a peak representing a second-order phase transition between 4 and 5 GPa for both the compositions. The pressure coefficient of electrical resistivity varied from -0.02 GPa to -0.06 GPa across transition pressure indicating a sluggish nature of transition. This is the first report of pressure effect on nanosized borderline compositions.

Glassy selenium at high pressure: Le Chatelier's principle still works

Science.gov (United States)

Brazhkin, V. V.; Tsiok, O. B.

2017-10-01

Selenium is the only easily vitrified elementary substance. Numerous experimental studies of glassy Se (g -Se) at high pressures show a large spread in the data on the compressibility and electrical resistivity of g -Se. Furthermore, H. Liu et al. [Proc. Natl. Acad. Sci. USA 105, 13229 (2008), 10.1073/pnas.0806857105] have arrived at the surprising conclusion that the volume of glass increases during pressure-induced crystallization. We have performed high-precision measurements of the specific volume and electrical resistivity of glassy selenium (g -Se) at high hydrostatic pressures up to 9 GPa. The measured bulk modulus at normal pressure is B =(9.0 5 ±0.15 ) GPa and its pressure derivative is BP'=6.4 ±0.2 . In the pressure range P <3 GPa, glassy selenium has an anomalously large negative second derivative of the bulk modulus. The electrical resistivity of g -Se decreases almost exponentially with increasing pressure and reaches 20 Ω cm at a pressure of 8.75 GPa. The inelastic behavior and weak relaxation of the volume for g -Se begin at pressures above 3.5 GPa; the volume and logarithm of the electrical resistivity relax significantly (logarithmically with the time) at pressures above 8 GPa. Bulk measurements certainly indicate that the volume of g -Se glass in the crystallization pressure range is larger than the volumes of both appearing crystalline phases (by 2% and 4%). Therefore, the "volume expansion phenomenon" suggested in [H. Liu et al., Proc. Natl. Acad. Sci. USA 105, 13229 (2008), 10.1073/pnas.0806857105] is not observed, and the pressure-induced crystallization of glassy selenium is consistent with the laws of thermodynamics.

Pressure dependence of BaNi2As2

Energy Technology Data Exchange (ETDEWEB)

Ronning, Filip [Los Alamos National Laboratory; Park, Tuscon [Los Alamos National Laboratory; Bauer, Eric D [Los Alamos National Laboratory; Thompson, Joe D [Los Alamos National Laboratory

2009-01-01

We report results from resistivity measurements of BaNi{sub 2}As{sub 2} up to 27.4 kbar of pressure. We find the structural transition at 130 K is broadened slightly with increasing pressure. There is also minimal influence on the superconducting transition, where the resistive onset increases from 2 to 3 K, but the temperature at which zero resistance is obtained is unchanged up to 27.4 kbar. This behavior is in contrast to that observed in the Fe-based systems as well as in LaNiPO and LaNiAsO.

Changes of bacterial diversity and tetracycline resistance in sludge from AAO systems upon exposure to tetracycline pressure

International Nuclear Information System (INIS)

Huang, Manhong; Qi, Fangfang; Wang, Jue; Xu, Qi; Lin, Li

2015-01-01

Highlights: • High-throughput sequencing was used to compare sludge bacteria with and without TC. • Bacterial diversity increased with TC addition despite of various oxygen conditions. • Total TRGs proliferated with TC addition in three kinds of sludge. • The concentration of efflux pump genes was the highest in the three groups of TRGs. - Abstract: Two lab-scale anaerobic-anoxic-oxic (AAO) systems were used to investigate the changes in tetracycline (TC) resistance and bacterial diversity upon exposure to TC pressure. High-throughput sequencing was used to detect diversity changes in microorganisms at the level of class in sludge from different bioreactors with and without TC. Real-time fluorescence quantitative polymerase chain reaction (RT-qPCR) was used to detect the abundances of eight tetracycline resistance genes (TRGs), tetA, tetB, tetC, tetE, tetM, tetO, tetS and tetX. The results showed that the diversities of the microbial communities of anoxic, anaerobic and aerobic sludge all increased with the addition of TC. TC substantially changed the structure of the microbial community regardless of oxygen conditions. Bacteroidetes and Proteobacteria were the dominant species in the three kinds of sludge and were substantially enriched with TC pressure. In sludge with TC added, almost all target TRGs proliferated more than those in sludge without TC except tetX, which decreased in anaerobic sludge with TC addition. The concentration of efflux pump genes, tet(A–C, E), was the highest among the three groups of TRGs in the different kinds of sludge

Changes of bacterial diversity and tetracycline resistance in sludge from AAO systems upon exposure to tetracycline pressure

Energy Technology Data Exchange (ETDEWEB)

Huang, Manhong, E-mail: egghmh@163.com; Qi, Fangfang; Wang, Jue; Xu, Qi; Lin, Li

2015-11-15

Highlights: • High-throughput sequencing was used to compare sludge bacteria with and without TC. • Bacterial diversity increased with TC addition despite of various oxygen conditions. • Total TRGs proliferated with TC addition in three kinds of sludge. • The concentration of efflux pump genes was the highest in the three groups of TRGs. - Abstract: Two lab-scale anaerobic-anoxic-oxic (AAO) systems were used to investigate the changes in tetracycline (TC) resistance and bacterial diversity upon exposure to TC pressure. High-throughput sequencing was used to detect diversity changes in microorganisms at the level of class in sludge from different bioreactors with and without TC. Real-time fluorescence quantitative polymerase chain reaction (RT-qPCR) was used to detect the abundances of eight tetracycline resistance genes (TRGs), tetA, tetB, tetC, tetE, tetM, tetO, tetS and tetX. The results showed that the diversities of the microbial communities of anoxic, anaerobic and aerobic sludge all increased with the addition of TC. TC substantially changed the structure of the microbial community regardless of oxygen conditions. Bacteroidetes and Proteobacteria were the dominant species in the three kinds of sludge and were substantially enriched with TC pressure. In sludge with TC added, almost all target TRGs proliferated more than those in sludge without TC except tetX, which decreased in anaerobic sludge with TC addition. The concentration of efflux pump genes, tet(A–C, E), was the highest among the three groups of TRGs in the different kinds of sludge.

Relationship between insulin resistance and plasma endothelin in hypertension patients

International Nuclear Information System (INIS)

Duan Yongqiang; Wang Zuobing; Yu Hui; Cao Wei; Wang Jing; Li Xiaoqin

2011-01-01

To explore the relationship between plasma endothelin and hypertension insulin resistance, and the improvement of insulin resistance in hypertension patients treated with captopril and l-amlodipine, 25 patients with primary hypertension and impaired glucose tolerance were selected and treated by captopril and l-amlodipine. Systolic pressure, diastolic pressure, fasting blood glucose, insulin and insulin antibody were measured before and after treatment and compared with healthy controls. The results showed that the plasma ET-1 level in hypertension group was significantly higher than that of healthy controls (P<0.01), and he plasma ET-1 level was positively correlated with FPG, FINS, Anti-INS, HOMA-IR. The systolic pressure, diastolic pressure, fasting blood glucose, insulin, insulin antibody and insulin resistance index in hypertension patients were decreased significantly after treatment (P<0.05). There is a good correlation between endothelin and insulin resistance index in hypertension patients. Captopril and l-amlodipine had obvious improvement effect on insulin resistance in hypertension patients. (authors)

How Heart Valves Evolve to Adapt to an Extreme-Pressure System

DEFF Research Database (Denmark)

Amstrup Funder, Jonas; Christian Danielsen, Carl; Baandrup, Ulrik

2017-01-01

BACKGROUND: Heart valves which exist naturally in an extreme-pressure system must have evolved in a way to resist the stresses of high pressure. Giraffes are interesting as they naturally have a blood pressure twice that of humans. Thus, knowledge regarding giraffe heart valves may aid...... in developing techniques to design improved pressure-resistant biological heart valves. METHODS: Heart valves from 12 giraffes and 10 calves were explanted and subjected to either biomechanical or morphological examinations. Strips from the heart valves were subjected to cyclic loading tests, followed...... in giraffes than in calves, which would make giraffe valves more resistant to the high-pressure forces. However, collagen also stiffens and thickens the valves. The mitral leaflets showed similar (but mostly insignificant) trends in strength, stiffness, and collagen content....

Construction of System for Seismic Observation in Deep Borehole (SODB) - Development of Multi-depth, High-temperature/pressure resistance seismometer

International Nuclear Information System (INIS)

Mamada, Yutaka

2014-01-01

The development of a high quality system for seismic observation in deep boreholes, the installation process at the NIIT site, and the data sharing plan for this observation were explained. The key points of the development were high temperature resistance (150 degrees Celsius), high pressure resistance (30 MPa), and a high dynamic/wide frequency range seismometer which allows for observation of micro-tremor to strong motions as well as a cascade-connection-type borehole seismometer, which allows multiple probes to be set at several depths in a single borehole. The developed system consists of broadband (0.1-50 Hz) and high dynamic range (up to 1000 gal) seismometer with electronic parts on the ground and only the pendulum part in the borehole (it became a servo-type seismometer). Durability and maintenance may be issues in the future. (author)

Tracking acquired antibiotic resistance in commensal bacteria of Galápagos land iguanas: no man, no resistance.

Directory of Open Access Journals (Sweden)

Maria Cristina Thaller

Full Text Available BACKGROUND: Antibiotic resistance, evolving and spreading among bacterial pathogens, poses a serious threat to human health. Antibiotic use for clinical, veterinary and agricultural practices provides the major selective pressure for emergence and persistence of acquired resistance determinants. However, resistance has also been found in the absence of antibiotic exposure, such as in bacteria from wildlife, raising a question about the mechanisms of emergence and persistence of resistant strains under similar conditions, and the implications for resistance control strategies. Since previous studies yielded some contrasting results, possibly due to differences in the ecological landscapes of the studied wildlife, we further investigated this issue in wildlife from a remote setting of the Galapagos archipelago. METHODOLOGY/PRINCIPAL FINDINGS: Screening for acquired antibiotic resistance was carried out in commensal enterobacteria from Conolophus pallidus, the terrestrial iguana of Isla Santa Fe, where: i the abiotic conditions ensure to microbes good survival possibilities in the environment; ii the animal density and their habits favour microbial circulation between individuals; and iii there is no history of antibiotic exposure and the impact of humans and introduced animal species is minimal except for restricted areas. Results revealed that acquired antibiotic resistance traits were exceedingly rare among bacteria, occurring only as non-dominant strains from an area of minor human impact. CONCLUSIONS/SIGNIFICANCE: Where both the exposure to antibiotics and the anthropic pressure are minimal, acquired antibiotic resistance traits are not normally found in bacteria from wildlife, even if the ecological landscape is highly favourable to bacterial circulation among animals. Monitoring antibiotic resistance in wildlife from remote areas could also be a useful tool to evaluate the impact of anthropic pressure.

Tracking acquired antibiotic resistance in commensal bacteria of Galápagos land iguanas: no man, no resistance.

Science.gov (United States)

Thaller, Maria Cristina; Migliore, Luciana; Marquez, Cruz; Tapia, Washington; Cedeño, Virna; Rossolini, Gian Maria; Gentile, Gabriele

2010-02-01

Antibiotic resistance, evolving and spreading among bacterial pathogens, poses a serious threat to human health. Antibiotic use for clinical, veterinary and agricultural practices provides the major selective pressure for emergence and persistence of acquired resistance determinants. However, resistance has also been found in the absence of antibiotic exposure, such as in bacteria from wildlife, raising a question about the mechanisms of emergence and persistence of resistant strains under similar conditions, and the implications for resistance control strategies. Since previous studies yielded some contrasting results, possibly due to differences in the ecological landscapes of the studied wildlife, we further investigated this issue in wildlife from a remote setting of the Galapagos archipelago. Screening for acquired antibiotic resistance was carried out in commensal enterobacteria from Conolophus pallidus, the terrestrial iguana of Isla Santa Fe, where: i) the abiotic conditions ensure to microbes good survival possibilities in the environment; ii) the animal density and their habits favour microbial circulation between individuals; and iii) there is no history of antibiotic exposure and the impact of humans and introduced animal species is minimal except for restricted areas. Results revealed that acquired antibiotic resistance traits were exceedingly rare among bacteria, occurring only as non-dominant strains from an area of minor human impact. Where both the exposure to antibiotics and the anthropic pressure are minimal, acquired antibiotic resistance traits are not normally found in bacteria from wildlife, even if the ecological landscape is highly favourable to bacterial circulation among animals. Monitoring antibiotic resistance in wildlife from remote areas could also be a useful tool to evaluate the impact of anthropic pressure.

A carbon nanotube-based pressure sensor

International Nuclear Information System (INIS)

Karimov, Kh S; Saleem, M; Khan, Adam; Qasuria, T A; Mateen, A; Karieva, Z M

2011-01-01

In this study, a carbon nanotube (CNT)-based Al/CNT/Al pressure sensor was designed, fabricated and investigated. The sensor was fabricated by depositing CNTs on an adhesive elastic polymer tape and placing this in an elastic casing. The diameter of multiwalled nanotubes varied between 10 and 30 nm. The nominal thickness of the CNT layers in the sensors was in the range ∼300-430 μm. The inter-electrode distance (length) and the width of the surface-type sensors were in the ranges 4-6 and 3-4 mm, respectively. The dc resistance of the sensors decreased 3-4 times as the pressure was increased up to 17 kN m -2 . The resistance-pressure relationships were simulated.

Safety shield for vacuum/pressure-chamber windows

Science.gov (United States)

Shimansky, R. A.; Spencer, R.

1980-01-01

Optically-clear shatter-resistant safety shield protects workers from implosion and explosion of vacuum and pressure windows. Plastic shield is inexpensive and may be added to vacuum chambers, pressure chambers, and gas-filling systems.

Pulsed-laser-deposited, single-crystalline Cu2O films with low resistivity achieved through manipulating the oxygen pressure

Science.gov (United States)

Liu, Xiaohui; Xu, Meng; Zhang, Xijian; Wang, Weiguang; Feng, Xianjin; Song, Aimin

2018-03-01

Low-resistivity, single-crystalline Cu2O films were realized on MgO (110) substrates through manipulating the oxygen pressure (PO2) of pulsed-laser deposition. X-ray diffraction and high resolution transmission electron microscopy measurements revealed that the films deposited at PO2 of 0.06 and 0.09 Pa were single phase Cu2O and the 0.09-Pa-deposited film exhibited the best crystallinity with an epitaxial relationship of Cu2O (110)∥MgO (110) with Cu2O (001)∥MgO (001). The pure phase Cu2O films exhibited higher transmittances and larger band gaps with an optical band gap of 2.56 eV obtained for the 0.09 Pa-deposited film. Hall-effect measurements demonstrated that the Cu2O film deposited at 0.09 Pa had the lowest resistivity of 6.67 Ω cm and highest Hall mobility of 23.75 cm2 v-1 s-1.

The Influence of the Basic Styrofoam Patterns Final Shaping Parameters on the Resistance Properties

Directory of Open Access Journals (Sweden)

T. Pacyniak

2012-12-01

Full Text Available This work presents the analysis of the final shaping process of the patterns aimed at determining the influence of the pressure and the time of sintering on the resistance to bending. The analysis of the research results proved that when the pressure of the sintering rises and reaches Ps=2.1 bar the resistance to bending increases, above this level of the pressure the resistance value starts decreasing. The time of styrofoam sintering at which the highest bending resistance values were obtained is ts=90 s. When the sintering pressure is less than 2 bar prolongation of the time of sintering over 90 s causes a slight increase in the resistance, however, at higher pressures prolongation of the time of sintering causes submelting of the styrofoam pattern.

The Influence of the Basic Styrofoam Patterns Final Shaping Parameters on the Resistance Properties

Directory of Open Access Journals (Sweden)

Pacyniak T.

2012-12-01

Full Text Available This work presents the analysis of the final shaping process of the patterns aimed at determining the influence of the pressure and the time of sintering on the resistance to bending. The analysis of the research results proved that when the pressure of the sintering rises and reaches Ps=2.1 bar the resistance to bending increases, above this level of the pressure the resistance value starts decreasing. The time of styrofoam sintering at which the highest bending resistance values were obtained is ts=90s. When the sintering pressure is less than 2 bar prolongation of the time of sintering over 90 s causes a slight increase in the resistance, however, at higher pressures prolongation of the time of sintering causes submelting of the styrofoam pattern.

A randomized 9-month study of blood pressure and body fat responses to aerobic training versus combined aerobic and resistance training in older men.

Science.gov (United States)

Sousa, Nelson; Mendes, Romeu; Abrantes, Catarina; Sampaio, Jaime; Oliveira, José

2013-08-01

This randomized study evaluated the impact of different exercise training modalities on blood pressure and body fat responses in apparently healthy older men. Forty-eight elderly men (aged 65-75 years) were randomly assigned to an aerobic training group (ATG, n=15), a combined aerobic and resistance training group (CTG, n=16), or a control group (n=17). Both exercise training programs were moderate-to-vigorous intensity, three days/week for 9-months. Strength, aerobic endurance, body fat and blood pressure were measured on five different occasions. The data were analyzed using a mixed-model ANOVA, and the independence between systolic blood pressure (SBP), diastolic blood pressure (DBP) and group was tested. A significant main effect of group (pendurance, with higher performance observed in the CTG. A significant main effect of group (ptraining programs reduce resting blood pressure. However, only the combined exercise training was effective at reducing body fat percentage; consequently, there were larger changes in blood pressure, which result in a significant reduction in hypertensive subjects. Copyright © 2013 Elsevier Inc. All rights reserved.

High-pressure effects on the superconductivity of β-pyrochlore oxides AOs2O6

International Nuclear Information System (INIS)

Muramatsu, Takaki; Takeshita, Nao; Terakura, Chikeko; Takagi, Hidenori; Tokura, Yoshinori; Yonezawa, Shigeki; Muraoka, Yuji; Hiroi, Zenji

2006-01-01

High-pressure effects on the superconducting transitions of β-pyrochlore oxide superconductors AOs 2 O 6 (A=Cs, Rb, K) are studied by measuring resistivity under high pressures up to 16 GPa. The superconducting transition temperature T c first increases with increasing pressure in all the compounds and then exhibits a broad maximum at 7.6 K (6 GPa), 8.2 K (2 GPa) and 10 K (0.6 GPa) for A=Cs, Rb and K, respectively. Finally, the superconductivity is suppressed completely at a critical pressure near 7 and 6 GPa for A=Rb and K and probably above 10 GPa for A=Cs. Characteristic changes in the temperature dependence of resistivity of RbOs 2 O 6 under high pressure. The residual resistivity largely increases with pressure above 4 GPa and, as a result, resistivity indicates small temperature dependence down to 4.2 K at 7 GPa and application of further pressure up to 10 GPa indicates that temperature dependence of resistivity decrease below 100 K. This characteristic behavior in the β-pyrochlore oxides may originate from the nesting of nearly octahedron shape of Fermi surface

The pressure gradient in the human respiratory tract

Directory of Open Access Journals (Sweden)

Chovancová Michaela

2014-03-01

Full Text Available Respiratory airways cause resistance to air flow during inhalation and exhalation. The pressure gradient is necessary to transport the air from the mount (or nose to pulmonary alveoli. The knowledge of pressure gradient (i.e. respiratory airways resistance is also needed to solve the question of aerosol deposition in the human respiratory tract. The obtained data will be used as boundary conditions for CFD simulations of aerosol transport. Understanding of aerosol transport in the human lungs can help us to determine the health hazard of harmful particles. On the other hand it can be used to set the conditions for transport of medication to the desirable place. This article deals with the description of the mathematical equations defining the pressure gradient and resistance in the bronchial three and describes the geometry used in the calculation.

Resistant Hypertension and Cardiorenovascular Risk

Directory of Open Access Journals (Sweden)

Prkacin Ingrid

2017-06-01

Full Text Available Studies have documented independent contribution of sympathetic activation to the cardiovascular disease continuum. Hypertension is one of the leading modifiable factors. Most if not all the benefit of antihypertensive treatment depends on blood pressure lowering, regardless how it is obtained. Resistant hypertension is defined as blood pressure that remains uncontrolled in spite of the concurrent use of three antihypertensive drugs of different classes. Ideally, one of the three drugs should be a diuretic, and all drugs should be prescribed at optimal dose amounts. Poor adherence to antihypertensive therapy, undiscovered secondary causes (e.g. obstructive sleep apnea, primary aldosteronism, renal artery stenosis, and lifestyle factors (e.g. obesity, excessive sodium intake, heavy alcohol intake, various drug interactions are the most common causes of resistant hypertension. Cardio(renovascular morbidity and mortality are significantly higher in resistant hypertensive than in general hypertensive population, as such patients are typically presented with a long-standing history of poorly controlled hypertension. Early diagnosis and treatment is needed to avoid further end-organ damage to prevent cardiorenovascular remodeling. Treatment strategy includes lifestyle changes, adding a mineralocorticoid receptor antagonist, treatment adherence in cardiovascular prevention and, in case of failure to control blood pressure, renal sympathetic denervation or baroreceptor activation therapy. The comparative outcomes in resistant hypertension deserve better understanding. In this review, the most current approaches to resistant hypertension and cardiovascular risk based on the available literature evidence will be discussed.

Microstructural stability of heat-resistant high-pressure die-cast Mg-4Al-4Ce alloy

Energy Technology Data Exchange (ETDEWEB)

Wang, Wei; Zhang, Jinghuai; Li, Guoqiang; Feng, Yan; Su, Minliang; Wu, Ruizhi; Zhang, Zhongwu [Harbin Engineering Univ. (China). Key Laboratory of Superlight Material and Surface Technology; Jiao, Yufeng [Jiamusi Univ. (China). College of Materials Science and Engineering

2017-05-15

The thermal stability of Al-RE (rare earth) intermetallic phases with individual RE for heat-resistant high-pressure die-casting Mg-Al-RE alloys is investigated. The results of this study show that the main strengthening phase of Mg-4Al-4Ce alloy is Al{sub 11}Ce{sub 3}, whose content is about 5 wt.% according to quantitative X-ray diffraction phase analysis. The Al{sub 11}Ce{sub 3} phase appears to have high thermal stability at 200 C and 300 C, while phase morphology change with no phase structure transition could occur for Al{sub 11}Ce{sub 3} when the temperature reaches 400 C. Furthermore, besides the kinds of rare earths and temperature, stress is also an influencing factor in the microstructural stability of Mg-4Al-4Ce alloy.

What Physical Fitness Component Is Most Closely Associated With Adolescents' Blood Pressure?

Science.gov (United States)

Nunes, Heloyse E G; Alves, Carlos A S; Gonçalves, Eliane C A; Silva, Diego A S

2017-12-01

This study aimed to determine which of four selected physical fitness variables, would be most associated with blood pressure changes (systolic and diastolic) in a large sample of adolescents. This was a descriptive and cross-sectional, epidemiological study of 1,117 adolescents aged 14-19 years from southern Brazil. Systolic and diastolic blood pressure were measured by a digital pressure device, and the selected physical fitness variables were body composition (body mass index), flexibility (sit-and-reach test), muscle strength/resistance (manual dynamometer), and aerobic fitness (Modified Canadian Aerobic Fitness Test). Simple and multiple linear regression analyses revealed that aerobic fitness and muscle strength/resistance best explained variations in systolic blood pressure for boys (17.3% and 7.4% of variance) and girls (7.4% of variance). Aerobic fitness, body composition, and muscle strength/resistance are all important indicators of blood pressure control, but aerobic fitness was a stronger predictor of systolic blood pressure in boys and of diastolic blood pressure in both sexes.

Decreasing electrical resistivity of silver along the melting boundary up to 5 GPa

Science.gov (United States)

Littleton, Joshua A. H.; Secco, Richard A.; Yong, Wenjun

2018-04-01

The electrical resistivity of Ag was experimentally measured at high pressures up to 5 GPa and at temperatures up to ∼300 K above melting. The resistivity decreased as a function of pressure and increased as a function of temperature as expected and is in very good agreement with 1 atm data. Observed melting temperatures at high pressures also agree well with previous experimental and theoretical studies. The main finding of this study is that resistivity of Ag decreases along the pressure- and temperature-dependent melting boundary, in conflict with prediction of resistivity invariance. This result is discussed in terms of the dominant contribution of the increasing energy separation between the Fermi level and 4d-band as a function of pressure. Calculated from the resistivity using the Wiedemann-Franz law, the electronic thermal conductivity increased as a function of pressure and decreased as a function of temperature as expected. The decrease in the high pressure thermal conductivity in the liquid phase as a function of temperature contrasts with the behavior of the 1 atm data.

Pressure-controlled drainage of cerebrospinal fluid: clinical experience with a new type of ventricular catheter (Ventcontrol MTC)and an integrated Piezo-resistive sensor at its tip: technical note.

Science.gov (United States)

Piek, J; Raes, P

1996-01-01

We described a new ventricular catheter that is the combination of a "classic" ventricular catheter with a piezo-resistive transducer at its tip. The device allows parallel recordings of intraventricular fluid pressure via a chip and a fluid-filled external transducer, drainage of cerebrospinal fluid from the ventricle or injection of fluid into the ventricle with simultaneous monitoring of intracranial pressure, and recording of brain tissue pressure in cases of misplacement or dislocation of the ventricular catheter or in cases of progressively narrowing ventricles caused by brain edema. Clinical tests in various situations at different pressure ranges (total recording time, 1356 h in 13 patients) gave excellent correlations of both pressures. Application of the device is especially indicated in clinical situations in which pressure-controlled drainage is desirable, occlusion of ventricular bolts is likely, or pressure-volume tests are needed.

Strength training reduces arterial blood pressure but not sympathetic neural activity in young normotensive subjects

Science.gov (United States)

Carter, Jason R.; Ray, Chester A.; Downs, Emily M.; Cooke, William H.

2003-01-01

The effects of resistance training on arterial blood pressure and muscle sympathetic nerve activity (MSNA) at rest have not been established. Although endurance training is commonly recommended to lower arterial blood pressure, it is not known whether similar adaptations occur with resistance training. Therefore, we tested the hypothesis that whole body resistance training reduces arterial blood pressure at rest, with concomitant reductions in MSNA. Twelve young [21 +/- 0.3 (SE) yr] subjects underwent a program of whole body resistance training 3 days/wk for 8 wk. Resting arterial blood pressure (n = 12; automated sphygmomanometer) and MSNA (n = 8; peroneal nerve microneurography) were measured during a 5-min period of supine rest before and after exercise training. Thirteen additional young (21 +/- 0.8 yr) subjects served as controls. Resistance training significantly increased one-repetition maximum values in all trained muscle groups (P < 0.001), and it significantly decreased systolic (130 +/- 3 to 121 +/- 2 mmHg; P = 0.01), diastolic (69 +/- 3 to 61 +/- 2 mmHg; P = 0.04), and mean (89 +/- 2 to 81 +/- 2 mmHg; P = 0.01) arterial blood pressures at rest. Resistance training did not affect MSNA or heart rate. Arterial blood pressures and MSNA were unchanged, but heart rate increased after 8 wk of relative inactivity for subjects in the control group (61 +/- 2 to 67 +/- 3 beats/min; P = 0.01). These results indicate that whole body resistance exercise training might decrease the risk for development of cardiovascular disease by lowering arterial blood pressure but that reductions of pressure are not coupled to resistance exercise-induced decreases of sympathetic tone.

Sensitivity of Spores of Eight Bacillus Cereus Strains to Pressure-Induced Germination by Moderate Hydrostatic Pressure, Time and Temperature

National Research Council Canada - National Science Library

Kalchayanand, Norasak; Ray, Bibek; Dunne, C. P; Sikes, Anthony

2005-01-01

The spores of eight Bacillus cereus strains were pressurized at 138 to 483 MPa for 5 to 20 min at 25 to 70 C in order to determine the sensitive and the resistant strains to pressure-induced germination...

Electrical behavior of Ca, Sr, Ba, and Eu at very high pressures and low temperatures

International Nuclear Information System (INIS)

Bundy, F.P.; Dunn, K.J.

1981-01-01

Compression of Ca and Sr initially causes an increase in resistivity, probably because of uncrossing of conduction and valence bands. Then at about 180 kbar for Ca and about 35 kbar for Sr the resistivity drops quite abruptly, following which the resistivity again increases with additional pressure, similar to the behavior of Ba starting at room pressure. The high pressure forms of Ba have already been reported to be superconducting, and the experiments confirm this. Superconductivity appears in Sr at about 350 kbar and develops strongly at higher pressures. In the 440 kbar experiment on Ca a resistance drop started at the lower threshold of the temperature capability, 2.1K, suggesting that Ca, too, becomes superconducting at sufficiently high pressures. The high pressure form of Eu above 125 kbar was tested for superconductivity down to 2.2K with negative results. (Auth.)

Relationship between systemic hemodynamics and ambulatory blood pressure level are sex dependent.

Science.gov (United States)

Alfie, J; Waisman, G D; Galarza, C R; Magi, M I; Vasvari, F; Mayorga, L M; Cámera, M I

1995-12-01

Sex-related differences in systemic hemodynamics were analyzed by means of cardiac index and systemic vascular resistance according to the level of daytime ambulatory blood pressure. In addition, we assessed the relations between ambulatory blood pressure measurements and systemic hemodynamics in male and female patients. We prospectively included 52 women and 53 men referred to our unit for evaluation of arterial hypertension. Women and men were grouped according to the level of daytime mean arterial pressure: or = 110 mm Hg. Patients underwent noninvasive evaluation of resting hemodynamics (impedance cardiography) and 24-hour ambulatory blood pressure monitoring. Compared with women men with lower daytime blood pressure had a 12% higher systemic vascular resistance index (P = NS) and a 14% lower cardiac index (P < .02), whereas men with higher daytime blood pressure had a 25% higher vascular resistance (P < .003) and a 21% lower cardiac index (P < .0004). Furthermore, in men systemic vascular resistance correlated positively with both daytime and nighttime systolic and diastolic blood pressures, whereas cardiac index correlated negatively only with daytime diastolic blood pressure. In contrast, women did not exhibit any significant correlation between hemodynamic parameters and ambulatory blood pressure measurements. In conclusion, sex-related differences in systemic hemodynamics were more pronounced in the group with higher daytime hypertension. The relations between systemic hemodynamics and ambulatory blood pressure level depended on the sex of the patient. In men a progressive circulatory impairment underlies the increasing level of ambulatory blood pressure, but this was not observed in women.

Thermopower measurement under high pressure using 'seesaw heating method'

International Nuclear Information System (INIS)

Hedo, M; Nakamura, D; Takaesu, Y; Yagasaki, K; Nakama, T; Fujiwara, T; Uchima, K

2010-01-01

We have developed a set-up with modified 'seesaw heating method' for the thermopower measurement under pressures P up to 3 GPa at the temperature range between 2 K and 300 K. By using this set-up, the thermopower and electrical resistivity of the single crystalline YbMn 2 Ge 2 under high pressure were measured with enough accuracy. S(T) curve shows the characteristic feature at the magnetic transition in all pressure range, while no evidence of the magnetic phase transition is observed in ρ(T) at P > 1.25 GPa. The measurement results indicate that the simultaneous measurement of the thermopower and electrical resistivity is a useful tool to study the pressure-induced phase transitions.

Design, fabrication and metrological evaluation of wearable pressure sensors.

Science.gov (United States)

Goy, C B; Menichetti, V; Yanicelli, L M; Lucero, J B; López, M A Gómez; Parodi, N F; Herrera, M C

2015-04-01

Pressure sensors are valuable transducers that are necessary in a huge number of medical application. However, the state of the art of compact and lightweight pressure sensors with the capability of measuring the contact pressure between two surfaces (contact pressure sensors) is very poor. In this work, several types of wearable contact pressure sensors are fabricated using different conductive textile materials and piezo-resistive films. The fabricated sensors differ in size, the textile conductor used and/or the number of layers of the sandwiched piezo-resistive film. The intention is to study, through the obtaining of their calibration curves, their metrological properties (repeatability, sensitivity and range) and determine which physical characteristics improve their ability for measuring contact pressures. It has been found that it is possible to obtain wearable contact pressure sensors through the proposed fabrication process with satisfactory repeatability, range and sensitivity; and that some of these properties can be improved by the physical characteristics of the sensors.

Development of resistance welding process. 4. Preparation of pressuring enclosed creep test specimen of 7A material

International Nuclear Information System (INIS)

Endo, Hideo; Seki, Masayuki; Ishibashi, Fujio; Hirako, Kazuhito; Tsukada, Tatsuya

2001-02-01

Mechanical strength in the position welded by resistance welding system was examined in 1999. The test specimens were destroyed in the welding position in a shorter time than expected in the creep test. Therefore, test specimens were prepared to evaluate the cause of destruction. Inner-pressure enclosed creep test specimens were prepared by resistance welding method. Cladding material with low deviation of thickness and high re-crystallization rate was used. Heat treatment after resistance welding was performed to remove the influence of residual stress and the precipitation of carbides. (1) Before preparation of specimens, the welding condition was fixed. Three test specimens were prepared. Two specimens without heat treatment were transported to MMS in Oarai Engineering Center on Aug. 4, 2000. One specimen with heat treatment was transported to MMS after evaluating the residual stress to get optimum heat treatment condition. (2) Specimens were prepared with welding end plugs to both ends of ferritic ODS cladding. Enclosing sides were welded with highly strong Ferritic/Martensitic steel end plugs. The other sides were welded with ferritic ODS end plugs. (3) Some kinds of electrical wave data were obtained during performing welding. Welding position was evaluated with supersonic detector after performing welding. (4) Mechanical strength of welding position in high temperature 800degC was confirmed to be equal to or larger than that of cladding material. The highly qualified specimens in the present were successfully prepared. (author)

Effects of short-term heated water-based exercise training on systemic blood pressure in patients with resistant hypertension: a pilot study.

Science.gov (United States)

Guimarães, Guilherme V; Cruz, Lais G B; Tavares, Aline C; Dorea, Egidio L; Fernandes-Silva, Miguel M; Bocchi, Edimar A

2013-12-01

High blood pressure (BP) increases the risk of cardiovascular diseases, and its control is a clinical challenge. Regular exercise lowers BP in patients with mild-to-moderate hypertension. No data are available on the effects of heated water-based exercise in hypertensive patients. Our objective was to evaluate the effects of heated water-based exercise on BP in patients with resistant hypertension. We tested the effects of 60-min heated water-based exercise training three times per week in 16 patients with resistant hypertension (age 55±6 years). The protocol included walking and callisthenic exercises. All patients underwent 24-h ambulatory blood pressure monitoring (ABPM) before and after a 2-week exercise program in a heated pool. Systolic office BP was reduced from 162 to 144 mmHg (Pexercise training during 24-h ABPM, systolic BP decreased from 135 to 123 mmHg (P=0.02), diastolic BP decreased from 83 to 74 mmHg (P=0.001), daytime systolic BP decreased from 141 to 125 mmHg (P=0.02), diastolic BP decreased from 87 to 77 mmHg (P=0.009), night-time systolic BP decreased from 128 to 118 mmHg (P=0.06), and diastolic BP decreased from 77 to 69 mmHg (P=0.01). In addition, BP cardiovascular load was reduced significantly during the 24-h daytime and night-time period after the heated water-based exercise. Heated water-based exercise reduced office BP and 24-h daytime and night-time ABPM levels. These effects suggest that heated water-based exercise may have a potential as a new therapeutic approach to resistant hypertensive patients.

High-Performance Pressure Sensor for Monitoring Mechanical Vibration and Air Pressure

Directory of Open Access Journals (Sweden)

Yancheng Meng

2018-05-01

Full Text Available To realize the practical applications of flexible pressure sensors, the high performance (sensitivity and response time as well as more functionalities are highly desired. In this work, we fabricated a piezoresistive pressure sensor based on the micro-structured composites films of multi-walled carbon nanotubes (MWCNTs and poly (dimethylsiloxane (PDMS. In addition, we establish efficient strategies to improve key performance of our pressure sensor. Its sensitivity is improved up to 474.13 kPa−1 by minimizing pressure independent resistance of sensor, and response time is shorten as small as 2 μs by enhancing the elastic modulus of polymer elastomer. Benefiting from the high performance, the functionalities of sensors are successfully extended to the accurate detection of high frequency mechanical vibration (~300 Hz and large range of air pressure (6–101 kPa, both of which are not achieved before.

The effects of moderate die pressure on banana-peel briquettes

Energy Technology Data Exchange (ETDEWEB)

Wilaipon, P. [Khon Kaen Univ., Khon Kaen (Thailand). Faculty of Engineering]|[Narasuan Univ., Phitsanulok (Thailand). Faculty of Engineering; Trirattanasirichai, K.; Tangchaichit, K. [Khon Kaen Univ., Khon Kaen (Thailand). Faculty of Engineering

2006-07-01

Bananas are one of the most important crops in Thailand, and are now being considered as a renewable energy source. This study investigated the impacts of moderate die pressure on banana peel briquettes. The pressure range in the study was set at 3-11 MPa. Water resistance characteristics were also analyzed. Four factors were considered: (1) the relaxation in length of the briquettes; (2) impact resistance; (3) relaxation in volume; and (4) water resistance. Experiments were conducted in laboratory conditions with humidity set at between 50 and 60 per cent at 27 degrees C. An impact resistance test was performed 168 hours after the briquetting process. The briquettes were immersed in water in order to conduct the water resistance test. Results of the tests demonstrated a rapid increase in the length of the briquettes. The maximum percentage of elongation occurred within 1 hour after being removed from the die. Results of the strength tests showed that the briquettes had a compaction pressure over 5 MPa. The briquettes showed significant potential as a biomass fuel. 15 refs., 1 tab., 12 figs.

Modifying Char Dustcake Pressure Drop Using Particulate Additives

Energy Technology Data Exchange (ETDEWEB)

Landham, C.; Dahlin, R.S.; Martin, R.A.; Guan, X.

2002-09-19

Coal gasification produces residual particles of coal char, coal ash, and sorbent that are suspended in the fuel gas stream exiting the gasifier. In most cases, these particles (referred to, hereafter, simply as char) must be removed from the stream prior to sending the gas to a turbine, fuel cell, or other downstream device. Currently, the most common approach to cleaning the gas stream at high temperature and pressure is by filtering the particulate with a porous ceramic or metal filter. However, because these dusts frequently have small size distributions, irregular morphology, and high specific surface areas, they can have very high gas flow resistance resulting in hot-gas filter system operating problems. Typical of gasification chars, the hot-gas filter dustcakes produced at the Power Systems Development Facility (PSDF) during recent coal gasification tests have had very high flow resistance (Martin et al, 2002). The filter system has been able to successfully operate, but pressure drops have been high and filter cleaning must occur very frequently. In anticipation of this problem, a study was conducted to investigate ways of reducing dustcake pressure drop. This paper will discuss the efficacy of adding low-flow-resistance particulate matter to the high-flow-resistance char dustcake to reduce dustcake pressure drop. The study had two parts: a laboratory screening study and confirming field measurements at the PSDF.

Pressure vessel lid

International Nuclear Information System (INIS)

Schoening, J.; Elter, C.; Becker, G.; Pertiller, S.

1986-01-01

The invention concerns a lid for closing openings in reactor pressure vessels containing helium, which is made as a circular casting with hollow spaces and a flat floor and is set on the opening and kept down. It consists of helium-tight metal cast material with sufficient temperature resistance. There are at least two concentric heat resistant seals let into the bottom of the lid. The bottom is in immediate contact with the container atmosphere and has hollow spaces in its inside in the area opposite to the opening. (orig./HP) [de

Does Pressure Accentuate General Relativistic Gravitational Collapse and Formation of Trapped Surfaces?

Science.gov (United States)

Mitra, Abhas

2013-04-01

It is widely believed that though pressure resists gravitational collapse in Newtonian gravity, it aids the same in general relativity (GR) so that GR collapse should eventually be similar to the monotonous free fall case. But we show that, even in the context of radiationless adiabatic collapse of a perfect fluid, pressure tends to resist GR collapse in a manner which is more pronounced than the corresponding Newtonian case and formation of trapped surfaces is inhibited. In fact there are many works which show such collapse to rebound or become oscillatory implying a tug of war between attractive gravity and repulsive pressure gradient. Furthermore, for an imperfect fluid, the resistive effect of pressure could be significant due to likely dramatic increase of tangential pressure beyond the "photon sphere." Indeed, with inclusion of tangential pressure, in principle, there can be static objects with surface gravitational redshift z → ∞. Therefore, pressure can certainly oppose gravitational contraction in GR in a significant manner in contradiction to the idea of Roger Penrose that GR continued collapse must be unstoppable.

Evaluation of an isotope washout technique to measure skin vascular resistance and skin perfusion pressure: influence of age, site and arterial surgery

International Nuclear Information System (INIS)

Duncan, H.J.; Faris, I.B.

1986-01-01

1. A simplified isotope (sup(99m)Tc) washout technique has been devised to calculate the skin perfusion pressure (SPP) and skin vascular resistance (SVR). This test is simple, requires inexpensive equipment and is well tolerated by patients. 2. SPP and SVR were calculated in 20 patients 30 years of age and in 15 patients with peripheral vascular disease (PVD). With increasing age the SPP and SVP were increased. The SPP was similar to the mean arterial pressure in normal individuals but was decreased in patients with PVD. The SPP is a useful indicator of the severity of the PVD. 3. The SPP and SVR were higher in the calf than in the foot. This is probably related to the decrease in pressure in the distal arterial tree. 4. SPP was increased by 110% and skin blood flow by 190% by arterial reconstructive surgery. This test may be of use in assessing the effectiveness of arterial surgery. (author)

Impact of calibration on estimates of central blood pressures.

Science.gov (United States)

Soender, T K; Van Bortel, L M; Møller, J E; Lambrechtsen, J; Hangaard, J; Egstrup, K

2012-12-01

Using the Sphygmocor device it is recommended that the radial pressure wave is calibrated for brachial systolic blood pressure (SBP) and diastolic blood pressure (DBP). However it has been suggested that brachial-to-radial pressure amplification causes underestimation of central blood pressures (BPs) using this calibration. In the present study we examined if different calibrations had an impact on estimates of central BPs and on the clinical interpretation of our results. On the basis of ambulatory BP measurements, patients were categorized into patients with controlled, uncontrolled or resistant hypertension. We first calibrated the radial pressure wave as recommended and afterwards recalibrated the same pressure wave using brachial DBP and calculated mean arterial pressure. Recalibration of the pressure wave generated significantly higher estimates of central SBP (P=0.0003 and Plost in patients with resistant hypertension (P=0.15). We conclude that calibration with DBP and mean arterial pressure produces higher estimates of central BPs than recommended calibration. The present study also shows that this difference between the two calibration methods can produce more than a systematic error and has an impact on interpretation of clinical results.

Studies on the resistance/reactivation of Giardia muris cysts and Cryptosporidium parvum oocysts exposed to medium-pressure ultraviolet radiation.

Science.gov (United States)

Belosevic, M; Craik, S A; Stafford, J L; Neumann, N F; Kruithof, J; Smith, D W

2001-10-16

The ex vivo and in vivo reactivation of Giardia muris cysts and Cryptosporidium parvum oocysts after exposure to different doses of ultraviolet (UV) radiation was determined using animal infectivity. The infectivity of UV-treated parasites stored for 1-4 days (G. muris) or 1-17 days (C. parvum) at room temperature in the dark was similar to that of organisms administered immediately after UV treatment, indicating that the parasites did not reactivate ex vivo. In contrast, we observed in vivo reactivation of G. muris in three of seven independent animal infectivity experiments, when parasites were treated with relatively low doses of medium-pressure UV (muris cysts and C. parvum oocysts exposed to medium-pressure UV doses of 60 mJ/cm(2) or higher did not exhibit resistance to and/or reactivation following treatment. This suggests that when appropriate doses of UV are used, significant and permanent inactivation of these parasites may be achieved.

Detection of resistance, cross-resistance, and stability of resistance to new chemistry insecticides in Bemisia tabaci (Homoptera: Aleyrodidae).

Science.gov (United States)

Basit, Muhammad; Saeed, Shafqat; Saleem, Mushtaq Ahmad; Denholm, Ian; Shah, Maqbool

2013-06-01

Resistance levels in whitefly, Bemisia tabaci (Gennadius) collections from cotton and sunflower (up to four districts) for five neonicotinoids and two insect growth regulators (IGRs) were investigated for two consecutive years. Based on the LC50(s), all collections showed slight to moderate levels of resistance for the tested insecticides compared with the laboratory susceptible population. The data also indicated that cotton and sunflower collections had similar resistance levels. In comparison (four collections), Vehari collections showed higher resistance for acetamiprid, thiacloprid, and nitenpyram compared with those of others. Average resistance ratios for acetamiprid, thiacloprid, and nitenpyram ranged from 5- to 13-, 4- to 8-, and 9- to 13-fold, respectively. Multan and Vehari collections also exhibited moderate levels (9- to 16-fold) of resistance to buprofezin. Furthermore, toxicity of neonicotinoids against immature stages was equal to that of insect growth regulators. The data also suggested that resistance in the field populations was stable. After selection for four generations with bifenthrin (G1 to G4), resistance to bifenthrin increased to 14-fold compared with the laboratory susceptible population. Selection also increased resistance to fenpropathrin, lambdacyhalothrin, imidacloprid, acetamiprid, and diafenthuron. Cross-resistance and stability of resistance in the field populations is of some concern. Rotation of insecticides having no cross-resistance and targeting the control against immature stages may control the resistant insects, simultaneously reducing the selection pressure imposed.

Resistant Hypertension : consequences and treatment options

NARCIS (Netherlands)

de Beus, E.

2017-01-01

Resistant hypertension, uncontrolled blood pressure despite use of ≥3 antihypertensives including a diuretic or use of ≥4 antihypertensives regardless of blood pressure (BP), was studied. In this thesis, 1/3 of patients with chronic kidney disease, including kidney transplant patients, is shown to

Methods for estimation and enhancing of resistance of pressure vessel materials to fracture at different stages of service taking into account actual dimensions of the construction

International Nuclear Information System (INIS)

Pokrovsky, V.V.; Ivanchenko, A.G.

1998-01-01

In the present report a method is proposed for assessment of cracked materials fracture toughness over a wide range of temperatures taking into account the size-effect of structural elements. The procedure proposed was evaluated on specimens of different thicknesses (25... 150 mm) and geometries from the parent metal and welded joint metal of the WWER-Type nuclear reactor pressure vessels of different classes of strength. The method of enhancing of fracture resistance of pressure vessel materials has been develop which is based on warm prestressing of materials with cracks. The stability of the favourable effect of the warm prestressing has been, investigated and shown for the above steels after their long term (to 24000 hours) keeping under static loading and temperature of 350 deg C, under different conditions of cyclic loading, corrosive action. A model and calculation procedure are proposed for predicting the influence of thermomechanical loading conditions on the resistance of reactor steels to brittle fracture. (authors)

Dynamic resistance training decreases sympathetic tone in hypertensive ovariectomized rats

Energy Technology Data Exchange (ETDEWEB)

Shimojo, G.L.; Palma, R.K.; Brito, J.O.; Sanches, I.C. [Laboratório de Fisiologia Translacional, Programa de Ciências da Reabilitação, Universidade Nove de Julho, São Paulo, SP (Brazil); Irigoyen, M.C. [Instituto do Coração, Faculdade de Medicina, Universidade de São Paulo, São Paulo, SP (Brazil); De Angelis, K. [Laboratório de Fisiologia Translacional, Programa de Ciências da Reabilitação, Universidade Nove de Julho, São Paulo, SP (Brazil)

2015-03-27

The aim of this study was to investigate the effects of resistance exercise training on hemodynamics and cardiac autonomic control in ovariectomized spontaneously hypertensive rats. Female rats were divided into 4 groups: sedentary control (SC), sedentary hypertensive (SH), sedentary hypertensive ovariectomized (SHO), and resistance-trained hypertensive ovariectomized (RTHO). Resistance exercise training was performed on a vertical ladder (5 days/week, 8 weeks) at 40-60% maximal load. Direct arterial pressure was recorded. Vagal and sympathetic tones were measured by heart rate (HR) responses to methylatropine (3 mg/kg, iv) and propranolol (4 mg/kg, iv). Ovariectomy resulted in additional increases in blood pressure in hypertensive rats and was associated with decreased vagal tone. Resistance exercise trained rats had lower mean arterial pressure than untrained rats (RTHO: 159±2.2 vs SHO: 177±3.4 mmHg), as well as resting bradycardia (RTHO: 332±9.0 vs SHO: 356±5 bpm). Sympathetic tone was also lower in the trained group. Moreover, sympathetic tone was positively correlated with resting HR (r=0.7, P<0.05). The additional arterial pressure increase in hypertensive rats caused by ovarian hormone deprivation was attenuated by moderate-intensity dynamic resistance training. This benefit may be associated with resting bradycardia and reduced cardiac sympathetic tone after training, which suggests potential benefits of resistance exercise for the management of hypertension after ovarian hormone deprivation.

Dynamic resistance training decreases sympathetic tone in hypertensive ovariectomized rats

International Nuclear Information System (INIS)

Shimojo, G.L.; Palma, R.K.; Brito, J.O.; Sanches, I.C.; Irigoyen, M.C.; De Angelis, K.

2015-01-01

The aim of this study was to investigate the effects of resistance exercise training on hemodynamics and cardiac autonomic control in ovariectomized spontaneously hypertensive rats. Female rats were divided into 4 groups: sedentary control (SC), sedentary hypertensive (SH), sedentary hypertensive ovariectomized (SHO), and resistance-trained hypertensive ovariectomized (RTHO). Resistance exercise training was performed on a vertical ladder (5 days/week, 8 weeks) at 40-60% maximal load. Direct arterial pressure was recorded. Vagal and sympathetic tones were measured by heart rate (HR) responses to methylatropine (3 mg/kg, iv) and propranolol (4 mg/kg, iv). Ovariectomy resulted in additional increases in blood pressure in hypertensive rats and was associated with decreased vagal tone. Resistance exercise trained rats had lower mean arterial pressure than untrained rats (RTHO: 159±2.2 vs SHO: 177±3.4 mmHg), as well as resting bradycardia (RTHO: 332±9.0 vs SHO: 356±5 bpm). Sympathetic tone was also lower in the trained group. Moreover, sympathetic tone was positively correlated with resting HR (r=0.7, P<0.05). The additional arterial pressure increase in hypertensive rats caused by ovarian hormone deprivation was attenuated by moderate-intensity dynamic resistance training. This benefit may be associated with resting bradycardia and reduced cardiac sympathetic tone after training, which suggests potential benefits of resistance exercise for the management of hypertension after ovarian hormone deprivation

Definition, identification and treatment of resistant hypertension in chronic kidney disease patients.

Science.gov (United States)

Drexler, Yelena R; Bomback, Andrew S

2014-07-01

Resistant hypertension, the inability to achieve goal blood pressure despite the use of three or more appropriately dosed antihypertensive drugs (including a diuretic), remains a common clinical problem, especially in patients with chronic kidney disease (CKD). While the exact prevalence and prognosis of resistant hypertension in CKD patients remain unknown, resistant hypertension likely contributes significantly to increased cardiovascular risk and progression of kidney disease in this population. We review the identification and evaluation of patients with resistant hypertension, including the importance of 24-h ambulatory blood pressure monitoring in the identification of 'white-coat', 'masked' and 'non-dipper' hypertension, the latter of which has particular clinical and therapeutic importance in patients with resistant hypertension and CKD. We then discuss treatment strategies for resistant hypertension that target the pathophysiologic mechanisms underlying resistance to treatment, including persistent volume excess, incomplete renin-angiotensin-aldosterone system blockade and inadequate nocturnal blood pressure control. Finally, we propose a treatment algorithm for evaluation and treatment of resistant hypertension in patients with CKD. © The Author 2013. Published by Oxford University Press on behalf of ERA-EDTA. All rights reserved.

Reproductive success of bromadiolone-resistant rats in absence of anticoagulant pressure

DEFF Research Database (Denmark)

Heiberg, Ann-Charlotte; Leirs, Herwig; Siegismund, Hans Redlef

2006-01-01

Resistance to anticoagulant rodenticides in brown rats (Rattus norvegicus Berk.) is associated with pleiotropic effects, notably with an increased dietary vitamin K requirement. Owing to this disadvantage, resistance is believed to be selected against if anticoagulant selection is absent. In small...... experimental populations of wild brown rats, an investigation was carried out to establish whether tolerance to anticoagulant exposure changed over a period of 2 years. In the same populations, DNA microsatellite markers were used to infer parentage, and this made it possible to estimate reproductive success...... of sensitive and resistant rats and estimate effective population size, Ne. Even though there was evidence for a selection against resistant rats with high vitamin K requirement, anticoagulant tolerance was not seen to be significantly influenced in the absence of bromadiolone selection. As the population size...

Research on pressure sensors for biomedical instruments

Science.gov (United States)

Angell, J. B.

1975-01-01

The development of a piezo-resistive pressure transducer is discussed suitable for recording pressures typically encountered in biomedical applications. The pressure transducer consists of a thin silicon diaphragm containing four strain-sensitive resistors, and is fabricated using silicon monolithic integrated-circuit technology. The pressure transducers can be as small as 0.7 mm outer diameter, and are, as a result, suitable for mounting at the tip of a catheter. Pressure-induced stress in the diaphragm is sensed by the resistors, which are interconnected to form a Wheatstone bridge.

Development of Zirconium alloys (for pressure tubes)

Energy Technology Data Exchange (ETDEWEB)

Kim, Young Suk; Kwon, Sang Chul; Choo, Ki Nam; Jung, Chung Hwan; Yim, Kyong Soo; Kim, Sung Soo; Baek, Jong Hyuk; Jeong, Yong Hwan; Kim, Kyong Ho; Cho, Hae Dong [Korea Atomic Energy Research Inst., Daeduk (Korea, Republic of); Hwang, S. K.; Kim, M. H. [Inha Univ., Incheon (Korea, Republic of); Kwon, S. I [Korea Univ., Seoul (Korea, Republic of); Kim, I. S. [Korea Advanced Inst. of Science and Technology, Taejon (Korea, Republic of)

1997-09-01

The objective of this research is to set up the basic technologies for the evaluation of pressure tube integrity and to develop improved zirconium alloys to prevent pressure tube failures due to DHC and hydride blister caused by excessive creep-down of pressure tubes. The experimental procedure and facilities for characterization of pressure tubes were developed. The basic research related to a better understanding of the in-reactor performances of pressure tubes leads to noticeable findings for the first time : the microstructural effect on corrosion and hydrogen pick-up behavior of Zr-2.5Nb pressure tubes, texture effect on strength and DHC resistance and enhanced recrystallization by Fe in zirconium alloys and etc. Analytical methodology for the assessment of pressure tubes with surface flaws was set up. A joint research is being under way with AECL to determine the fracture toughness of O-8 at the EOL (End of Life) that had been quadruple melted and was taken out of the Wolsung Unit-1 after 10 year operation. In addition, pressure tube with texture controlled is being made along with VNINM in Russia as a joint project between KAERI and Russia. Finally, we succeeded in developing 4 different kinds of zirconium alloys with better corrosion resistance, low hydrogen pickup fraction and higher creep strength. (author). 121 refs., 65 tabs., 260 figs

High-pressure-assisted synthesis of high-volume ZnGeP2 polycrystalline

Science.gov (United States)

Huang, Changbao; Wu, Haixin; Xiao, Ruichun; Chen, Shijing; Ma, Jiaren

2018-06-01

The pnictide and chalcogenide semiconductors are promising materials for the applications in the field of photoelectric. High-purity and high-volume polycrystalline required in the real-world applications is hard to be synthesized due to the high vapor pressure of phosphorus and sulfur components at high temperature. A new high-pressure-resisted method was used to investigate the synthesis of the nonlinear-optical semiconductor ZnGeP2. The high-purity ZnGeP2 polycrystalline material of approximately 500 g was synthesized in one run, which enables the preparation of nominally stoichiometric material. Since increasing internal pressure resistance of quartz crucible and reducing the reaction space, the high-pressure-resisted method can be used to rapidly synthesize other pnictide and chalcogenide semiconductors and control the components ratio.

Statistical models of a gas diffusion electrode: II. Current resistent

Energy Technology Data Exchange (ETDEWEB)

Proksch, D B; Winsel, O W

1965-07-01

The authors describe an apparatus for measuring the flow resistance of gas diffusion electrodes which is a mechanical analog of the Wheatstone bridge for measuring electric resistance. The flow resistance of a circular DSK electrode sheet, consisting of two covering layers and a working layer between them, was measured as a function of the gas pressure. While the pressure first was increased and then decreased, a hysteresis occurred, which is discussed and explained by a statistical model of a porous electrode.

Flexible pressure sensors for smart protective clothing against impact loading

International Nuclear Information System (INIS)

Wang, Fei; Zhu, Bo; Shu, Lin; Tao, Xiaoming

2014-01-01

The development of smart protective clothing will facilitate the quick detection of injuries from contact sports, traffic collisions and other accidents. To obtain real-time information like spatial and temporal pressure distributions on the clothing, flexible pressure sensor arrays are required. Based on a resistive fabric strain sensor we demonstrate all flexible, resistive pressure sensors with a large workable pressure range (0–8 MPa), a high sensitivity (1 MPa −1 ) and an excellent repeatability (lowest non-repeatability ±2.4% from 0.8 to 8 MPa) that can be inexpensively fabricated using fabric strain sensors and biocompatible polydimethylsiloxane (PDMS). The pressure sensitivity is tunable by using elastomers with different elasticities or by the pre-strain control of fabric strain sensors. Finite element simulation further confirms the sensor design. The simple structure, large workable pressure range, high sensitivity, high flexibility, facile fabrication and low cost of these pressure sensors make them promising candidates for smart protective clothing against impact loading. (paper)

Mechanisms of pressure-mediated cell death and injury in Escherichia coli: from fundamentals to food applications.

Directory of Open Access Journals (Sweden)

Michael eGänzle

2015-06-01

Full Text Available High hydrostatic pressure is commercially applied to extend the shelf life of foods, and to improve food safety. Current applications operate at ambient temperature and 600 MPa or less. However, bacteria that may resist this pressure level include the pathogens Staphylococcus aureus and strains of Escherichia coli, including shiga-toxin producing E. coli. The resistance of E. coli to pressure is variable between strains and highly dependent on the food matrix. The targeted design of processes for the safe elimination of E. coli thus necessitates deeper insights into mechanisms of interaction and matrix-strain interactions. Cellular targets of high pressure treatment in E. coli include the barrier properties of the outer membrane, the integrity of the cytoplasmic membrane as well as the activity of membrane-bound enzymes, and the integrity of ribosomes. The pressure-induced denaturation of membrane bound enzymes results in generation of reactive oxygen species and subsequent cell death caused by oxidative stress. Remarkably, pressure resistance at the single cell level relates to the disposition of misfolded proteins in inclusion bodies. While the pressure resistance E. coli can be manipulated by over-expression or deletion of (stress proteins, the mechanisms of pressure resistance in wild type strains is multi-factorial and not fully understood. This review aims to provide an overview on mechanisms of pressure-mediated cell death in E. coli, and the use of this information for optimization of high pressure processing of foods.

Mechanisms of pressure-mediated cell death and injury in Escherichia coli: from fundamentals to food applications.

Science.gov (United States)

Gänzle, Michael; Liu, Yang

2015-01-01

High hydrostatic pressure is commercially applied to extend the shelf life of foods, and to improve food safety. Current applications operate at ambient temperature and 600 MPa or less. However, bacteria that may resist this pressure level include the pathogens Staphylococcus aureus and strains of Escherichia coli, including shiga-toxin producing E. coli. The resistance of E. coli to pressure is variable between strains and highly dependent on the food matrix. The targeted design of processes for the safe elimination of E. coli thus necessitates deeper insights into mechanisms of interaction and matrix-strain interactions. Cellular targets of high pressure treatment in E. coli include the barrier properties of the outer membrane, the integrity of the cytoplasmic membrane as well as the activity of membrane-bound enzymes, and the integrity of ribosomes. The pressure-induced denaturation of membrane bound enzymes results in generation of reactive oxygen species and subsequent cell death caused by oxidative stress. Remarkably, pressure resistance at the single cell level relates to the disposition of misfolded proteins in inclusion bodies. While the pressure resistance E. coli can be manipulated by over-expression or deletion of (stress) proteins, the mechanisms of pressure resistance in wild type strains is multi-factorial and not fully understood. This review aims to provide an overview on mechanisms of pressure-mediated cell death in E. coli, and the use of this information for optimization of high pressure processing of foods.

The Prehistory of Antibiotic Resistance.

Science.gov (United States)

Perry, Julie; Waglechner, Nicholas; Wright, Gerard

2016-06-01

Antibiotic resistance is a global problem that is reaching crisis levels. The global collection of resistance genes in clinical and environmental samples is the antibiotic "resistome," and is subject to the selective pressure of human activity. The origin of many modern resistance genes in pathogens is likely environmental bacteria, including antibiotic producing organisms that have existed for millennia. Recent work has uncovered resistance in ancient permafrost, isolated caves, and in human specimens preserved for hundreds of years. Together with bioinformatic analyses on modern-day sequences, these studies predict an ancient origin of resistance that long precedes the use of antibiotics in the clinic. Understanding the history of antibiotic resistance is important in predicting its future evolution. Copyright © 2016 Cold Spring Harbor Laboratory Press; all rights reserved.

Potential benefits of exercise on blood pressure and vascular function.

Science.gov (United States)

Pal, Sebely; Radavelli-Bagatini, Simone; Ho, Suleen

2013-01-01

Physical activity seems to enhance cardiovascular fitness during the course of the lifecycle, improve blood pressure, and is associated with decreased prevalence of hypertension and coronary heart disease. It may also delay or prevent age-related increases in arterial stiffness. It is unclear if specific exercise types (aerobic, resistance, or combination) have a better effect on blood pressure and vascular function. This review was written based on previous original articles, systematic reviews, and meta-analyses indexed on PubMed from years 1975 to 2012 to identify studies on different types of exercise and the associations or effects on blood pressure and vascular function. In summary, aerobic exercise (30 to 40 minutes of training at 60% to 85% of predicted maximal heart rate, most days of the week) appears to significantly improve blood pressure and reduce augmentation index. Resistance training (three to four sets of eight to 12 repetitions at 10 repetition maximum, 3 days a week) appears to significantly improve blood pressure, whereas combination exercise training (15 minutes of aerobic and 15 minutes of resistance, 5 days a week) is beneficial to vascular function, but at a lower scale. Aerobic exercise seems to better benefit blood pressure and vascular function. Copyright © 2013 American Society of Hypertension. Published by Elsevier Inc. All rights reserved.

High pressure studies of as grown WX2-x single crystals

International Nuclear Information System (INIS)

Solanki, G.K.; Agarwal, M.K.; Patel, Yogesh A.

2011-01-01

The structural optical and transport properties of tungsten metal dichalogenides having layered structure have been extensively studied in the last two decades. These materials shows highly anisotropic behaviour and have been receiving considerable interest for a variety of applications. Several of these layered semiconductors have attracted attention as a new class of solar cell material. We present here the results of simultaneous resistivity and thermoelectric power (TEP) measurements upto 7 GPa on single crystals of WS 2 , WS 1.9 , WSe 2 and WSe 1.9 grown using Direct Vapour Transport (DVT) technique. The observations clearly shows WS 2 and WS 1.9 are more resistive compared to other two crystals. In all samples an exponential fall of resistivity on increases in pressure upto 2.1 GPa but after 2.2 GPa the resistivity decreases substantially with increases pressure. The TEP of WSe 2 increases steadily and reaches maximum at 0.65 GPa, while for WSe 1.9 TEP increases upto pressure 0.5 GPa. In both the cases after attaining the maximum TEP, then decreases monotonically with increase in pressure. TEP of WS 2 and WS 1.9 increase upto pressure 1.1 GPa, beyond 1.1 GPa pressure in both the cases TEP decreases steadily with further increase in pressure. In all the samples, the sign of TEP is positive indicating that all of them are p-type and remain p-type with increase in pressure. The variation of thermoelectric power factor with pressure has been thoroughly studied. An analysis of the data point out that perfectly stoichiometric crystals of WSe 2 work as superior thermoelectric materials. The results have been presented and implications have been discussed. (author)

Nitroglycerin-mediated, but not flow-mediated vasodilation, is associated with blunted nocturnal blood pressure fall in patients with resistant hypertension.

Science.gov (United States)

Fontes-Guerra, Priscila C A; Cardoso, Claudia R L; Muxfeldt, Elizabeth S; Salles, Gil F

2015-08-01

Endothelial function by flow-mediated (FMD) and nitroglycerin-mediated vasodilations (NMD) was scarcely investigated in resistant hypertension. We aimed to assess the independent correlates of FMD and NMD in resistant hypertensive patients, particularly their associations with ambulatory blood pressures (BP) and nocturnal BP fall patterns. In a cross-sectional study, 280 resistant hypertensive patients performed 24-h ambulatory BP monitoring, carotid-femoral pulse wave velocity, polysomnography, and brachial artery FMD and NMD by high-resolution ultrasonography. Independent correlates of FMD, NMD, and brachial artery diameter (BAD) were assessed by multiple linear and logistic regressions. Median (interquartile range) FMD was 0.75% (-0.6 to +4.4%) and NMD was 11.8% (7.1-18.4%). Baseline BAD and diabetes were independently associated with both FMD and NMD. Older age and prior cardiovascular diseases were associated with altered FMD, whereas higher night-time SBP and lower nocturnal SBP fall were associated with impaired NMD. Moreover, there was a significant gradient of impaired NMD according to blunted nocturnal BP decline patterns. BAD was independently associated with age, sex, BMI, albuminuria, and nocturnal SBP fall. Further adjustments to blood flow velocity, aortic stiffness, plasma aldosterone concentration, and sleep apnea did not change these relationships. NMD, but not FMD, is independently associated with unfavorable night-time BP levels and nondipping patterns, and may be a better cardiovascular risk marker in patients with resistant hypertension. BAD also may provide additional prognostic information.

Fabrication and Characterization of a Pressure Sensor using a Pitch-based Carbon Fiber

International Nuclear Information System (INIS)

Park, Chang Sin; Kang, Bo Seon; Lee, Dong Weon

2007-01-01

This paper reports fabrication and characterization of a pressure sensor using a pitch-based carbon fiber. Pitch-based carbon fibers have been shown to exhibit the piezoresistive effect, in which the electric resistance of the carbon fiber changes under mechanical deformation. The main structure of pressure sensors was built by performing backside etching on a SOI wafer and creating a suspended square membrane on the front side. An AC electric field which causes dielectrophoresis was used for the alignment and deposition of a carbon fiber across the microscale gap between two electrodes on the membrane. The fabricated pressure sensors were tested by applying static pressure to the membrane and measuring the resistance change of the carbon fiber. The resistance change of carbon fibers clearly shows linear response to the applied pressure and the calculated sensitivities of pressure sensors are 0.25∼0.35 and 61.8 Ω/kΩ·bar for thicker and thinner membrane, respectively. All these observations demonstrated the possibilities of carbon fiber-based pressure sensors

Van der Waals pressure sensors using reduced graphene oxide composites

Science.gov (United States)

Jung, Ju Ra; Ahn, Sung Il

2018-04-01

Reduced graphene oxide (RGO) films intercalated with various polymers were fabricated by reaction-based self-assembly, and their characteristics as vacuum pressure sensors based on van der Waals interactions were studied. At low temperature, the electrical resistances of the samples decrease linearly with increasing vacuum pressure, whereas at high temperature the variation of the electrical resistance shows secondary order curves. Among all samples, the poly vinyl alcohol intercalated RGO shows the highest sensitivity, being almost two times more sensitive than reference RGO. All samples show almost the same signal for repetitive sudden pressure changes, indicating reasonable reproducibility and durability.

High pressure transport and micro-calorimetry studies on quantum phase transitions in Yb heavy fermion systems

International Nuclear Information System (INIS)

Colombier, E; Braithwaite, D; Lapertot, G; Salce, B; Knebel, G; Flouquet, J

2008-01-01

We present ac microcalorimetry and resistivity measurements under high pressure on new very pure single crystals of YbCu 2 Si 2 having residual resistivity ratios of up to 130 and residual resistivities of less than 1 μΩcm. The onset of magnetic order at high pressure has been detected by ac micro-calorimetry in a diamond anvil cell, and the phase diagram has been established showing magnetic order appearing at 7.6 GPa and 0.95K, and suggesting a possible quantum critical point at a pressure of about 6.5 GPa. The resistivity has been measured under pressure in hydrostatic conditions, but no sign of superconductivity is found close to the expected critical pressure down to T=0.05 K. We discuss these results in comparison with results on cerium based heavy fermion systems

Hyperelastic pressure sensing with a liquid-embedded elastomer

International Nuclear Information System (INIS)

Park, Yong-Lae; Wood, Robert J; Majidi, Carmel; Kramer, Rebecca; Bérard, Phillipe

2010-01-01

A hyperelastic pressure transducer is fabricated by embedding silicone rubber with microchannels of conductive liquid eutectic gallium–indium. Pressing the surface of the elastomer with pressures in the range of 0–100 kPa will deform the cross-section of underlying channels and change their electric resistance by as much as 50%. Microchannels with dimensions as small as 25 µm are obtained with a maskless, soft lithography process that utilizes direct laser exposure. Change in electrical resistance is measured as a function of the magnitude and area of the surface pressure as well as the cross-sectional geometry, depth and relative lateral position of the embedded channel. These experimentally measured values closely match closed-form theoretical predictions derived from plane strain elasticity and contact mechanics

The Proliferation Resistance of a Nuclear Fuel Cycle Using Fuel Recovered from the Electrolytic Reduction of Pressurized Water Reactor Spent Fuel

Energy Technology Data Exchange (ETDEWEB)

Kang, Jung Min; Cochran, Thomas; Mckinzie, Matthew [NRDC, Washington, (United States)

2016-05-15

At some points in the fuel cycle, a level of intrinsic or technical proliferation-resistance can be provided by radiation barriers that surround weapons-usable materials. In this report we examine some aspects of intrinsic proliferation resistance of a fuel cycle for a fast neutron reactor that uses fuel recovered from the electrolytic reduction process of pressurized water reactor spent fuel, followed by a melt-refining process. This fuel cycle, proposed by a nuclear engineer at the Korea Advanced Institute of Science and Technology (KAIST), is being examined with respect to its potential merits of higher fuel utilization, lower production of radioactive byproducts, and better economics relative to a pyroprocesing-based fuel cycle. With respect to intrinsic proliferation resistance, however, we show that since europium is separated out during the electrolytic reduction process, this fuel cycle has little merit beyond that of a pyroprocessing-based fuel cycle because of the lower radiation barrier of its recovered materials containing weapons-usable actinides. Unless europium is not separated following voloxidation, the proposed KAIST fuel cycle is not intrinsically proliferation resistant and in this regard does not represent a significant improvement over pyroprocessing. We suggest further modification of the proposed KAIST fuel cycle, namely, omitting electrolytic reduction and melt reduction, and producing the fast reactor fuel directly following voloxidation.

Resistance within hemodialysis shunts predicts patency.

Science.gov (United States)

Bui, Trung D; Gordon, Ian L; Parashar, Amish; Vo, David; Wilson, Samuel E

2006-01-01

The authors examined the relationship between patency after thrombectomy of clotted dialysis grafts and intraoperative measurements of flow (Q), pressure gradient (PGR), and longitudinal resistance (RL). Eighteen thrombosed arteriovenous (AV) grafts underwent 21 thrombectomies. Pressures at arterial (P1) and venous (P2) ends of the AV grafts were determined with 22-gauge catheters and standard transducers; flow was measured with transit-time probes; arithmetic averaging of waveforms was used to compute mean Q, PGR, and RL. Kaplan-Meier patency curves were analyzed by using log rank methods. Mean patency for all grafts was 164 +/-152 days. For each variable, the 21 measurements were split and the patency curve for the grafts with the 11 lowest value grafts was compared to the curve representing the 10 highest value grafts. The difference between high RL versus low RL patency curves was significant with high-resistance grafts having a median patency of 55 days and low-resistance grafts having a median patency greater than 151 days (p = 0.0089). In contrast, the high Q group median patency was 151 days versus 174 days for the low Q group (p = 0.86). Median patency for the low PGR group was 115 days compared to 62 days for the high PGR group (p = 0.162). Longitudinal resistance within AV grafts, but not flow or pressure gradient, showed a significant correlation with patency after thrombectomy. Increased resistance to flow within AV grafts appears to be an important factor affecting the propensity of dialysis grafts to thrombose.

Tearing mode saturation with finite pressure

International Nuclear Information System (INIS)

Lee, J.K.

1988-01-01

With finite pressure, the saturation of the current-driven tearing mode is obtained in three-dimensional nonlinear resistive magnetohydrodynamic simulations for Tokamak plasmas. To effectively focus on the tearing modes, the perturbed pressure effects are excluded while the finite equilibrium pressure effects are retained. With this model, the linear growth rates of the tearing modes are found to be very insensitive to the equilibrium pressure increase. The nonlinear aspects of the tearing modes, however, are found to be very sensitive to the pressure increase in that the saturation level of the nonlinear harmonics of the tearing modes increases monotonically with the pressure rise. The increased level is associated with enhanced tearing island sizes or increased stochastic magnetic field region. (author)

Blood pressure from childhood to adolescence in obese youths in relation to insulin resistance and asymmetric dimethylarginine.

Science.gov (United States)

de Giorgis, T; Marcovecchio, M L; Giannini, C; Chiavaroli, V; Chiarelli, F; Mohn, A

2016-02-01

Hypertension is the most important cardiovascular complication of obesity, even during childhood. Several studies have demonstrated that there is a natural progression of hypertension from childhood to adulthood. However, there are no data reporting a potential worsening in blood pressure (BP) already moving from the pre-pubertal to the pubertal period in obese youths. The aim of this study was to evaluate early change in BP and its relation to insulin resistance (IR) and asymmetric dimethylarginine (ADMA). Thirty obese children underwent a first assessment when they were pre-pubertal (visit_1) and were re-evaluated after a mean of 4.5 years (visit_2). At both visits, anthropometric parameters were assessed, blood samples were collected for measurement of insulin, glucose and ADMA and a 24-h ambulatory BP monitoring was performed. At visit_2, the study participants presented increased HOMA-IR and ADMA compared to visit_1 (HOMA-IR: 3.6 ± 2.8 vs 2.8 ± 1.4, p = 0.01; ADMA: 1.57 ± 0.78 vs 0.77 ± 0.52 μmol/l, p childhood to adolescence (p obese children, and modifications in insulin resistance and ADMA seem to be implicated in this early progression in BP.

Carbon nanotube—cuprous oxide composite based pressure sensors

International Nuclear Information System (INIS)

Karimov, Kh. S.; Chani, Muhammad Tariq Saeed; Khalid, Fazal Ahmad; Khan, Adam; Khan, Rahim

2012-01-01

In this paper, we present the design, the fabrication, and the experimental results of carbon nanotube (CNT) and Cu 2 O composite based pressure sensors. The pressed tablets of the CNT—Cu 2 O composite are fabricated at a pressure of 353 MPa. The diameters of the multiwalled nanotubes (MWNTs) are between 10 nm and 30 nm. The sizes of the Cu 2 O micro particles are in the range of 3–4 μm. The average diameter and the average thickness of the pressed tablets are 10 mm and 4.0 mm, respectively. In order to make low resistance electric contacts, the two sides of the pressed tablet are covered by silver pastes. The direct current resistance of the pressure sensor decreases by 3.3 times as the pressure increases up to 37 kN/m 2 . The simulation result of the resistance—pressure relationship is in good agreement with the experimental result within a variation of ±2%. (condensed matter: structural, mechanical, and thermal properties)

Pressure Sensitive Sensors Based on Carbon Nanotubes, Graphene, and Its Composites

Directory of Open Access Journals (Sweden)

Asar Ali

2018-01-01

Full Text Available Carbon nanotubes (CNTs and graphene have attracted a great deal of interest due to their outstanding mechanical, optical, electrical, and structural properties. Most of the scientists and researchers have investigated the optical and electrical properties of these materials. However, due to unique electromechanical properties of these materials, it is required to explore the piezoresistive properties of bulk nanostructured CNTs, graphene, and CNT-graphene composites. We investigated and compared the sensitivities and piezoresistive properties of sandwich-type pure CNT, pure graphene, and CNT-graphene composite pressure sensors. For all the samples, increase in pressure from 0 to 0.183 kNm−2 results in a decrease in the impedance and direct current (DC resistance. Sensitivity and percentage decrease in resistance and impedance of CNT-graphene composite were lower than pure CNT while being higher than pure graphene based sample. Moreover, under the same external applied pressure, the sensitivity and percentage decrease in impedance for pure CNT, pure graphene, and CNT-graphene composite were smaller than the corresponding sensitivity and percentage decrease in resistance. The achieved experimental results of the composite sample were compared with simulated results which exhibit reasonable agreement with each other. The deviations of simulated resistance-pressure and impedance-pressure curves from experimental graphs were 0.029% and 0.105%, respectively.

Cantilever arrayed blood pressure sensor for arterial applanation tonometry.

Science.gov (United States)

Lee, Byeungleul; Jeong, Jinwoo; Kim, Jinseok; Kim, Bonghwan; Chun, Kukjin

2014-03-01

The authors developed a cantilever-arrayed blood pressure sensor array fabricated by (111) silicon bulk-micromachining for the non-invasive and continuous measurement of blood pressure. The blood pressure sensor measures the blood pressure based on the change in the resistance of the piezoresistor on a 5-microm-thick-arrayed perforated membrane and 20-microm-thick metal pads. The length and the width of the unit membrane are 210 and 310 microm, respectively. The width of the insensible zone between the adjacent units is only 10 microm. The resistance change over contact force was measured to verify the performance. The good linearity of the result confirmed that the polydimethylsiloxane package transfers the forces appropriately. The measured sensitivity was about 4.5%/N. The maximum measurement range and the resolution of the fabricated blood pressure sensor were greater than 900 mmHg (= 120 kPa) and less than 1 mmHg (= 133.3 Pa), respectively.

SrRuO3 thin films grown on MgO substrates at different oxygen partial pressures

KAUST Repository

Zou, Bin

2013-01-08

A comprehensive study of SrRuO3 thin films growth on (001) MgO substrates by pulsed laser deposition in a wide oxygen pressure range from 10 to 300 mTorr was carried out. The experimental results showed a correlation between the lattice constants, resistivity, and oxygen partial pressures used. Ru deficiency detected only in films deposited at lower oxygen pressures (<50 mTorr), resulted in an elongation of the in-plane and out-of-plane lattice constants and an increase in the film resistivity. When deposited with oxygen partial pressure of 50 mTorr, SrRuO3 films had lattice parameters matching those of bulk SrRuO3 material and exhibited room temperature resistivity of 320 μΩ·cm. The resistivity of SrRuO 3/MgO films decreased with increasing oxygen partial pressure. Copyright © 2013 Materials Research Society.

The Effect of Applied Pressure During Feeding of Critical Cast Aluminum Alloy Components With Particular Reference to Fatigue Resistance

Energy Technology Data Exchange (ETDEWEB)

J.T. Berry; R. Luck; B. Zhang; R.P. Taylor

2003-06-30

the medium to long freezing range alloys of aluminum such as A356, A357, A206, 319 for example are known to exhibit dispersed porosity, which is recognized as a factor affecting ductility, fracture toughness, and fatigue resistance of light alloy castings. The local thermal environment, for example, temperature gradient and freezing from velocity, affect the mode of solidification which, along with alloy composition, heat treatment, oxide film occlusion, hydrogen content, and the extent to which the alloy contracts on solidification, combine to exert strong effects on the porosity formation in such alloys. In addition to such factors, the availability of liquid metal and its ability to flow through the partially solidified casting, which will be affect by the pressure in the liquid metal, must also be considered. The supply of molten metal will thus be controlled by the volume of the riser available for feeding the particular casting location, its solidification time, and its location together with any external pressure that might be applied at the riser.

The effect of spironolactone in patients with resistant arterial hypertension in relation to baseline blood pressure and secondary causes of hypertension.

Science.gov (United States)

Vaclavik, Jan; Sedlak, Richard; Jarkovsky, Jiri; Kocianova, Eva; Taborsky, Milos

2013-03-01

There are currently limited data about whether the effect of spironolactone in patients with resistant arterial hypertension depends on baseline blood pressure and the presence of a secondary cause of hypertension. Patients with office systolic blood pressure (BP) >140 mmHg or diastolic BP >90 mmHg, despite treatment with at least 3 antihypertensive drugs including a diuretic, were randomly assigned to receive spironolactone or a placebo for 8 weeks in a double-blind, placebo-controlled, multicentre trial (ASPIRANT). Analyses were done with 55 patients treated with spironolactone. The degree of BP reduction after 8 weeks of spironolactone treatment did not differ significantly between the three tertiles of baseline systolic BP and patients with and without a secondary cause of hypertension. The reduction of office systolic, office diastolic BP and office pulse pressure was significantly lower in the highest tertile with baseline diastolic BP > 97 mmHg. Spironolactone treatment is effective to a similar extent both in patients with and without a secondary cause of hypertension and regardless of the baseline value of systolic BP. Less effect of spironolactone was found in patients with the highest baseline diastolic BP.

Drug resistance in the sexually transmitted protozoan Trichomonas vaginalis

Institute of Scientific and Technical Information of China (English)

REBECCA L DUNNE; LINDA A DUNN; PETER UPCROFT; PETER J O'DONOGHUE; JACQUELINE A UPCROFT

2003-01-01

Trichomoniasis is the most common, sexually transmitted infection. It is caused by the flagellated protozoan parasite Trichomonas vaginalis. Symptoms include vaginitis and infections have been associated with preterm delivery, low birth weight and increased infant mortality, as well as predisposing to HIV/AIDS and cervical cancer. Trichomoniasis has the highest prevalence and incidence of any sexually transmitted infection. The 5-nitroimidazole drugs, of which metronidazole is the most prescribed, are the only approved,effective drugs to treat trichomoniasis. Resistance against metronidazole is frequently reported and crossresistance among the family of 5-nitroimidazole drugs is common, leaving no alternative for treatment, with some cases remaining unresolved. The mechanism of metronidazole resistance in T. vaginalis from treatment failures is not well understood, unlike resistance which is developed in the laboratory under increasing metronidazole pressure. In the latter situation, hydrogenosomal function which is involved in activation of the prodrug, metronidazole, is down-regulated. Reversion to sensitivity is incomplete after removal of drug pressure in the highly resistant parasites while clinically resistant strains, so far analysed, maintain their resistance levels in the absence of drug pressure. Although anaerobic resistance has been regarded as a laboratory induced phenomenon, it clearly has been demonstrated in clinical isolates. Pursuit of both approaches will allow dissection of the underlying mechanisms. Many alternative drugs and treatments have been tested in vivo in cases of refractory trichomoniasis, as well as in vitro with some successes including the broad spectrum anti-parasitic drug nitazoxanide. Drug resistance incidence in T. vaginalis appears to be on the increase and improved surveillance of treatment failures is urged.

Slip-rolling resistance of novel Zr(C,N) thin film coatings under high Hertzian contact pressures

Energy Technology Data Exchange (ETDEWEB)

Manier, Charles-Alix

2010-08-24

Today, coatings are used in many applications ranging from the decoration purposes to the improvement of efficiency such as in machining tools, medical tools, computer devices (hard disks) and many more. Especially the automotive industry anticipates a benefit in using coatings for example in powertrains and gears where the mechanical components are stressed under slip-rolling motion. A cost effective option to increase efficiency is based on the increase of the load carrying capacity by thin film coatings. It would also represent a way towards downsizing. In the work presented here, a small review concerning rolling contact fatigue of coatings was performed. Experimentally it is then shown, that crystalline Zr(C,N) coatings can be slip-rolling resistant at 120 C in factory fill engine oil up to ten million cycles under average Hertzian contact pressures up to P{sub 0mean} = 1.94 GPa (P{sub 0max} = 2.91 GPa). Basically, it represents here the doubling of the normal force acting on the surface compared to uncoated steel traditionally lubricated with fully formulated oil. Typically, the coated substrates are made of the quenched and tempered bearing steel Cronidur 30. The Zr(C,N) coatings were fully characterized using different characterisation techniques in order to understand the difference in slip-rolling resistance under those high tribological demands. Effectively, the slip-rolling resistance of different batches of the Zr(C,N) coatings is evaluated using a defined and powerful testing procedure. Different results of lifetime were achieved without fundamental changes of the deposition procedure. The characterisation achieved permits the identification of microstructural disparities which should affect the load carrying capacity of the coating. Moreover, the efficiency of the high slip-rolling resistant Zr(C,N) coating was considered not only with respect to the improvement of the load carrying capacity of the substrate but also in terms of tribological

A vacuum pressure sensor based on ZnO nanobelt film

International Nuclear Information System (INIS)

Zheng, X J; Cao, X C; Sun, J; Yuan, B; Zhu, Z; Zhang, Y; Li, Q H

2011-01-01

A vacuum pressure sensor was fabricated by assembling ZnO nanobelt film on the interdigital electrodes, and the current-voltage characteristics were measured with an Agilent semiconductor parameter tester. Under different pressures of 1.0 x 10 3 , 6.7 x 10 -3 , 8.2 x 10 -4 and 9.5 x 10 -5 mbar, the currents are 8.71, 28.1, 46.1 and 89.6 nA, and the pressure sensitive resistances are 1150, 356, 217 and 112 MΩ, respectively. In the range of 10 -5 -10 3 mbar the smaller the pressure is, the higher the current is. The pressure sensitive resistance of the vacuum pressure sensor increases linearly with the logarithmic pressure, and the measurement range is at least one order of magnitude wider than that of the previous sensors. Under the final pressure, the vacuum pressure sensor has maximum sensitivity (9.29) and power consumption of 0.9 μW. The sensitivity is larger than that of the previous sensor based on a ZnO single nanowire at that pressure, and the power consumption is much lower than that for the sensor based on a ZnO nanowire array. The pressure sensitive mechanism is reasonably explained by using oxygen chemisorption and energy band theory.

Electrical properties of pressure quenched silicon by thermal spraying

International Nuclear Information System (INIS)

Tan, S.Y.; Gambino, R.J.; Sampath, S.; Herman, H.

2007-01-01

High velocity thermal spray deposition of polycrystalline silicon film onto single crystal substrates, yields metastable high pressure forms of silicon in nanocrystalline form within the deposit. The phases observed in the deposit include hexagonal diamond-Si, R-8, BC-8 and Si-IX. The peculiar attribute of this transformation is that it occurs only on orientation silicon substrate. The silicon deposits containing the high pressure phases display a substantially higher electrical conductivity. The resistivity profile of the silicon deposit containing shock induced metastable silicon phases identified by X-ray diffraction patterns. The density of the pressure induced polymorphic silicon is higher at deposit/substrate interface. A modified two-layer model is presented to explain the resistivity of the deposit impacted by the pressure induced polymorphic silicon generated by the thermal spraying process. The pressure quenched silicon deposits on the p - silicon substrate, with or without metastable phases, display the barrier potential of about 0.72 eV. The measured hall mobility value of pressure quenched silicon deposits is in the range of polycrystalline silicon. The significance of this work lies in the fact that the versatility of thermal spray may enable applications of these high pressure forms of silicon

Organic electronics based pressure sensor towards intracranial pressure monitoring

Science.gov (United States)

Rai, Pratyush; Varadan, Vijay K.

2010-04-01

The intra-cranial space, which houses the brain, contains cerebrospinal fluid (CSF) that acts as a fluid suspension medium for the brain. The CSF is always in circulation, is secreted in the cranium and is drained out through ducts called epidural veins. The venous drainage system has inherent resistance to the flow. Pressure is developed inside the cranium, which is similar to a rigid compartment. Normally a pressure of 5-15 mm Hg, in excess of atmospheric pressure, is observed at different locations inside the cranium. Increase in Intra-Cranial Pressure (ICP) can be caused by change in CSF volume caused by cerebral tumors, meningitis, by edema of a head injury or diseases related to cerebral atrophy. Hence, efficient ways of monitoring ICP need to be developed. A sensor system and monitoring scheme has been discussed here. The system architecture consists of a membrane less piezoelectric pressure sensitive element, organic thin film transistor (OTFT) based signal transduction, and signal telemetry. The components were fabricated on flexible substrate and have been assembled using flip-chip packaging technology. Material science and fabrication processes, subjective to the device performance, have been discussed. Capability of the device in detecting pressure variation, within the ICP pressure range, is investigated and applicability of measurement scheme to medical conditions has been argued for. Also, applications of such a sensor-OTFT assembly for logic sensor switching and patient specific-secure monitoring system have been discussed.

Recovery in cold-worked alloy under pressure: example of AISI 316 stainless steel

Energy Technology Data Exchange (ETDEWEB)

Yousuf, M; Sahu, P C; Raghunathan, V S; Govinda Rajan, K

1986-06-01

In this paper we report the behaviour of defects under high pressure in severely cold-deformed 316 stainless steel. In situ electrical resistivity measurements indicate a minimum in the reduced resistivity ratio at 2 GPa associated with a characteristic relaxation time of 500 + - 5 sec. Microhardness data on pressure-treated and recovered samples are consistent with the electrical resistivity behaviour. X-ray powder diffraction rings indicate sharpening beyond 2 GPa. The decrease in the full width at half maximum (FWHM) of the strongest ring is about 2% at pressures beyond 2 GPa. Transmission electron microscopy reveals that samples pressure treated beyond 2 GPa have a polygonized dislocation structure. This is in sharp contrast to the tangled dislocation structure observed in the cold-worked samples. The experimental results suggest a recovery stage in cold-worked stainless steel at 2 GPa. We propose that the recovery process is activated through an enhanced vacancy concentration caused by deformation, a pressure-induced vacancy-dislocation interaction and consequently a pressure-assisted dislocation mobility leading to polygonization.

Cerebral Pulsatility Index Is Elevated in Patients with Elevated Right Atrial Pressure.

Science.gov (United States)

Lahiri, Shouri; Schlick, Konrad H; Padrick, Matthew M; Rinsky, Brenda; Gonzalez, Nestor; Jones, Heather; Mayer, Stephan A; Lyden, Patrick D

2018-01-01

Extracerebral venous congestion can precipitate intracranial hypertension due to obstruction of cerebral blood outflow. Conditions that increase right atrial pressure, such as hypervolemia, are thought to increase resistance to jugular venous outflow and contribute to cerebro-venous congestion. Cerebral pulsatility index (CPI) is considered a surrogate marker of distal cerebrovascular resistance and is elevated with intracranial hypertension. Thus, we sought to test the hypothesis that elevated right atrial pressure is associated with increased CPI compared to normal right atrial pressure. We retrospectively reviewed 61 consecutive patients with subarachnoid hemorrhage. We calculated CPI from transcranial Doppler studies and correlated these with echocardiographic measures of right atrial pressure. CPIs were compared from patients with elevated and normal right atrial pressure. There was a significant difference between CPI obtained from all patients with elevated right atrial pressure compared to those with normal right atrial pressure (P right and left hemispheric CPI from patients with both elevated and normal right atrial pressure. Patients with elevated right atrial pressure had significantly higher CPI compared to patients with normal right atrial pressure. These findings suggest that cerebro-venous congestion due to impaired jugular venous outflow may increase distal cerebrovascular resistance as measured by CPI. Since elevated CPI is associated with poor outcome in numerous neurological conditions, future studies are needed to elucidate the significance of these results in other populations. Copyright © 2017 by the American Society of Neuroimaging.

Resistance of Aedes aegypti to temephos and adaptive disadvantages

Directory of Open Access Journals (Sweden)

Morgana Michele Cavalcanti de Souza Leal Diniz

2014-10-01

Full Text Available OBJECTIVE To evaluate the resistance of Aedes aegypti to temephos Fersol 1G (temephos 1% w/w associated with the adaptive disadvantage of insect populations in the absence of selection pressure. METHODS A diagnostic dose of 0.28 mg a.i./L and doses between 0.28 mg a.i./L and 1.40 mg a.i./L were used. Vector populations collected between 2007 and 2008 in the city of Campina Grande, state of Paraíba, were evaluated. To evaluate competition in the absence of selection pressure, insect populations with initial frequencies of 20.0%, 40.0%, 60.0%, and 80.0% resistant individuals were produced and subjected to the diagnostic dose for two months. Evaluation of the development of aquatic and adult stages allowed comparison of the life cycles in susceptible and resistant populations and construction of fertility life tables. RESULTS No mortality was observed in Ae. aegypti populations subjected to the diagnostic dose of 0.28 mg a.i./L. The decreased mortality observed in populations containing 20.0%, 40.0%, 60.0%, and 80.0% resistant insects indicates that temephos resistance is unstable in the absence of selection pressure. A comparison of the life cycles indicated differences in the duration and viability of the larval phase, but no differences were observed in embryo development, sex ratio, adult longevity, and number of eggs per female. CONCLUSIONS The fertility life table results indicated that some populations had reproductive disadvantages compared with the susceptible population in the absence of selection pressure, indicating the presence of a fitness cost in populations resistant to temephos.

Applied pressure-dependent anisotropic grain connectivity in shock consolidated MgB{sub 2} samples

Energy Technology Data Exchange (ETDEWEB)

Ohashi, Wataru [Graduate School of Engineering, University of Yamanashi, Takeda 4-3-11, Kofu 400-8511 (Japan); Takenaka, Kenta [Graduate School of Engineering, University of Yamanashi, Takeda 4-3-11, Kofu 400-8511 (Japan); Kondo, Tadashi [Graduate School of Engineering, University of Yamanashi, Takeda 4-3-11, Kofu 400-8511 (Japan); Tamaki, Hideyuki [Graduate School of Engineering, University of Yamanashi, Takeda 4-3-11, Kofu 400-8511 (Japan); Matsuzawa, Hidenori [Graduate School of Engineering, University of Yamanashi, Takeda 4-3-11, Kofu 400-8511 (Japan)]. E-mail: matuzawa@mx3.nns.ne.jp; Kai, Shoichiro [Advanced Materials and Process Development Group, Explosive Division, Asahi Kasei Chemicals Corporation, Oita 870-0392 (Japan); Kakimoto, Etsuji [Advanced Materials and Process Development Group, Explosive Division, Asahi Kasei Chemicals Corporation, Oita 870-0392 (Japan); Takano, Yoshihiko [National Institute for Materials Science, Tsukuba 305-0047 (Japan); Minehara, Eisuke [FEL Laboratory, Tokai Site, Japan Atomic Energy Research Institute, Shirakata-shirane 2-4, Tokai, Ibaraki 319-1195 (Japan)

2006-09-15

Three different cylindrical MgB{sub 2} bulk samples were prepared by the underwater shock consolidation method in which shock waves of several GPa, generated by detonation of explosives, were applied to a metallic cylinder containing commercially available MgB{sub 2} powders with no additives. Resistivity anisotropy of the samples increased with shock pressure. The highest- and medium-pressure applied samples had finite resistivities in the radial direction for the whole temperature range down to 12 K, whereas their axial and azimuthal resistivities dropped to zero at 32-35 K. By contrast, the lowest-pressure applied sample was approximately isotropic with a normal-state resistivity of {approx}40 {mu}{omega} cm, an onset temperature of {approx}38.5 K, and a transition width of {approx}4.5 K. These extremely anisotropic properties would have resulted from the distortion of grain boundaries and grain cores, caused by the shock pressures and their repeated bouncing.

Pressure effects on the carbon nano-tube embedded Y-123 superconductors

Energy Technology Data Exchange (ETDEWEB)

Dadras, Sedigheh, E-mail: dadras@alzahra.ac.ir [Department of Physics, Alzahra University, Tehran 1993893973 (Iran, Islamic Republic of); Manivannan, Nallayian [CeNSCMR & FPRD, Department of Physics and Astronomy, Seoul National University, Seoul 151-747 (Korea, Republic of); Daadmehr, Vahid [Department of Physics, Alzahra University, Tehran 1993893973 (Iran, Islamic Republic of); Rezakhani, Ali Tayefeh [Department of Physics, Sharif University of Technology, Tehran (Iran, Islamic Republic of); Kim, Kee Hoon [CeNSCMR & FPRD, Department of Physics and Astronomy, Seoul National University, Seoul 151-747 (Korea, Republic of)

2016-04-15

It has been known that applying pressure and doping carbon nano-tubes (CNTs) can each affect the behavior of high temperature superconductors. Here, bridging these two effects in order to see how they can interplay, we investigate how the dc resistivity varies in both pure and CNT-doped polycrystalline YBa{sub 2}Cu{sub 3}O{sub 7−δ} (Y-123) compounds under hydrostatic pressure. We demonstrate that the broadening of the resistivity transition in the CNT-doped samples (of 0.7 wt%) is smaller than the undoped samples. In addition, by increasing applied pressure, the doped samples exhibit a higher rate of the increase of the transition temperatures T{sub c}{sup on} and T{sub c}{sup mid} than the undoped samples. Interestingly as well, under applied pressure of 1.5 GPa, it is found that T{sub c}{sup on} for the doped samples (99.39 K) is relatively higher than in the undoped samples (96.88 K). The doped samples also show more robustness versus applied pressure in the sense that they have smaller variations of resistivity. In particular, we observed that the increase rate of the normal resistivity in the CNT-doped samples is nearly four times smaller than the undoped samples. This may be a manifestation of relative robustness of the doped samples against fractures of the links between grains. These observations, overall, may suggest that the CNT doping, due to unique mechanical characteristics of CNTs, can enhance superconductivity properties of Y-123 superconductors under applied pressure.

Acute tamponade alters subendo- and subepicardial pressure-flow relations differently during vasodilation.

Science.gov (United States)

Kingma, J G; Martin, J; Rouleau, J R

1994-07-01

Instantaneous diastolic left coronary artery pressure-flow relations (PFR) shift during acute tamponade as pressure surrounding the heart increases. Coronary pressure at zero flow (Pf = 0) on the linear portion of the PFR is the weighted mean of the different myocardial waterfall pressures, the distribution of which varies across the left ventricular wall during diastole. However, instantaneous PFR measured in large epicardial coronary arteries cannot be used to estimate Pf = 0 in the different myocardial tissue layers. During coronary vasodilatation in a capacitance-free model, myocardial PFR differs from subendocardium to subepicardium. Therefore, we studied the effects of acute tamponade during maximal pharmacology induced coronary vasodilatation on myocardial PFR in in situ anesthetized dogs. Tamponade reduced cardiac output, aortic pressure, and coronary blood flow. Results demonstrate that different mechanisms influence distribution of myocardial blood flow during tamponade. Subepicardial vascular resistance is unchanged and the extrapolated Pf = 0 is increased, thereby shifting PFR to a higher intercept on the pressure axis. Subendocardial vascular resistance is increased while the extrapolated Pf = 0 remains unchanged. Results indicate that in the setting of acute tamponade with coronary vasodilatation different mechanisms regulate the distribution of myocardial blood flow: in the subepicardium only outflow pressure increases, whereas in the subendocardium only vascular resistance increases.

Electrical resistivity of YbRh{sub 2}Si{sub 2} and EuT{sub 2}Ge{sub 2} (T=Co,Cu) at extreme conditions of pressure and temperature

Energy Technology Data Exchange (ETDEWEB)

Dionicio, G.A.

2006-07-01

This investigation addresses the effect that pressure, p, and temperature, T, have on 4f states of the rare-earth elements in the isostructural YbRh{sub 2}Si{sub 2}, EuCo{sub 2}Ge{sub 2}, and EuCu{sub 2}Ge{sub 2} compounds. Upon applying pressure the volume of the unit cell reduces, enforcing either the enhancement of the hybridization of the 4f localized electrons with the ligand or a change in the valence state of the rare-earth ions. Here, we probe the effect of a pressure-induced lattice contraction on these system by means of electrical-resistivity measurements, {rho}(T), from room temperature down to 100 mK. (orig.)

Huge residual resistivity in the quantum critical region of CeAgSb2

International Nuclear Information System (INIS)

Nakashima, Miho; Kirita, Shingo; Asai, Rihito; Kobayashi, Tatsuo C; Okubo, Tomoyuki; Yamada, Mineko; Thamizhavel, Arumugam; Inada, Yoshihiko; Settai, Rikio; Galatanu, Andre; Yamamoto, Etsuji; Ebihara, Takao; Onuki, Yoshichika

2003-01-01

We have studied the effect of pressure on the electrical resistivity of a high-quality single crystal CeAgSb 2 which has a small net ferromagnetic moment of 0.4μ B /Ce. The magnetic ordering temperature T ord = 9.7 K decreases with increasing pressure p and disappears at a critical pressure p c ≅ 3.3 GPa. The residual resistivity, which is close to zero up to 3 GPa, increases steeply above 3 GPa, reaching 55μΩ cm at p c . A huge residual resistivity is found to appear when the magnetic order disappears. (letter to the editor)

Superconductivity in an Organic Solid at Zero Pressure

DEFF Research Database (Denmark)

Bechgaard, Klaus; da Costa Carneiro, Kim; Jacobsen, C.S.

1981-01-01

Resistance measurements in the organic conductor (TMTSF)2C104 have given evidence of superconductivity in the absence of applied pressure. Transition temperatures were between 1.2 and 1.4 K for different crystals. A transverse magnetic field of 25 mT nearly restores normal resistance at 0.9 K. Th...

Antiretroviral Resistance in HIV/AIDS Patients

Science.gov (United States)

Manosuthi, W.; MD

2018-03-01

The higher prevalence of HIV drug resistance was observed in areas with greater ART coverage. The HIV resistance-associated mutations occur when people have inadequate levels of antiretroviral drugs as well as inadequate potency, inadequate adherence, and preexisting resistance. The degree to drug cross-resistance is observed depends on the specific mutations and number of mutation accumulation. In the Southeast Asia region, the challenging of people with treatment failure is the availability and accessibility to subsequent new antiretroviral drugs to construct he second and salvage regimen. Genotypic resistance testing is a useful tool because it can identify the existing drug resistance-associated mutations under the selective drug pressure. Thus, understanding the basic interpretation of HIV drug resistance- associated mutation is useful in guiding clinical decisions for treatment-experienced people living with HIV.

Diamond dispersed cemented carbide produced without using ultra high pressure equipment

International Nuclear Information System (INIS)

Moriguchi, H.; Tsuzuki, K.; Ikegaya, A.

2001-01-01

We have developed a composite material of dispersed diamond particles in cemented carbide without using ultra high pressure equipment. The developed diamond dispersed cemented carbide combines the excellent properties of cemented carbide with diamond and also provides 1.5 times improved fracture toughness over that of cemented carbide. They also show 10 times higher wear resistance over that of cemented carbide in a wear resistance test against bearing steel, and 5 times greater grindability than diamond compacts. Because ultra high pressure equipment is not used to produce the developed material, large compacts over 100 mm in diameter can be manufactured. The developed material showed 10-25 times higher wear resistance in real use as wear-resistant tools such as centerless blades and work-rests. (author)

Pressure cycling induced modification of a cemented carbide

International Nuclear Information System (INIS)

Beste, U.; Engqvist, H.; Jacobson, S.

2001-01-01

The wear of cemented carbide rock drill buttons is due to a complex mixture of mechanisms. One important of such mechanism is the surface fatigue that occurs due to the percussive conditions of rock drilling. To isolate the effects of this mechanism, a mechanical pressure cycling test has been performed on a cemented carbide with 11 % Co and 2 μm WC grain size. The test was ended after 60000 pressure cycles. No signs of fatigue crack nucleation were found. The changes in hardness, fracture toughness, erosion resistance, magnetical coercivity and thermal shock resistance were measured. The microstructure of the sample was investigated with x-ray diffraction, plus scanning and transmission electron microscopy. The fracture toughness decreased 14 % due to the pressure cycling while the hardness did not change. In addition, the thermal shock resistance and the erosion resistance decreased. The magnetical coercivity increased 90 % indicating significant phase transformations or high defect density in the Co binder phase. The TEM revealed no deformation of the WC phase, but important alterations of the Co phase. The Co phase was transformed from fcc into a new unidentified phase, characterized by atomic inter planar distance present in fcc and hcp plus an unfamiliar distance of 2.35 Aa. This phase is suggested to be due to a more complex stacking sequence of the close-packed planes than in hcp or fcc. (author)

Sustained effect of resistance training on blood pressure and hand grip strength following a detraining period in elderly hypertensive women: a pilot study

Directory of Open Access Journals (Sweden)

Nascimento D da C

2014-01-01

Full Text Available Dahan da Cunha Nascimento,1,5,8 Ramires Alsamir Tibana,1,8 Franklin M Benik,2 Keila Elizabeth Fontana,3 Frederico Ribeiro Neto,8 Frederico Santos de Santana,5,8 Leopoldo Santos-Neto,4 Renato André Sousa Silva,1,5,6 Alessandro Oliveira Silva,1,7 Darlan Lopes Farias,1,7 Sandor Balsamo,4,5,8 Jonato Prestes1 1Postgraduate Program in Physical Education, Catholic University of Brasilia, Brasilia, Brazil; 2Department of Kinesiology and Sports Studies Graduate Program, Eastern Illinois University, Charleston, IL, USA; 3Faculty of Physical Education, University of Brasilia, Brasilia, Brazil; 4Graduate Program in Medical Sciences of the University of Brasilia, School of Medicine and Rheumatology Service, University Hospital of Brasilia (HUB, Brasilia, Brazil; 5Department of Physical Education, University Center Euro American University Center, Brasilia, Brazil; 6Center of Excellence in Medicine of Exercise (CEMEx, Brasilia, Brazil; 7Center University of Brasilia (UNICEUB, Brasilia, Brazil; 8Strength Training and Health Research Group (GEPEEFS, Brasilia, Brazil Introduction: Hypertension is the most prevalent modifiable risk factor with a high prevalence among older adults. Exercise is a nonpharmacological treatment shown to benefit all patients with hypertension. Objective: This study examined the effects of a 14-week moderate intensity resistance training program (RT on the maintenance of blood pressure and hand grip strength during an extended detraining period in elderly hypertensive women. Methods: Twelve hypertensive sedentary elderly women completed 14 weeks of whole body RT at a moderate perceived exertion following a detraining period of 14 weeks. Results: Following the training period, participants demonstrated an increase in absolute hand grip strength (P=0.001, relative hand grip strength (P=0.032 and a decrease of systolic (P=0.001, diastolic (P=0.008, and mean blood pressure (P=0.002 when compared to pre-exercise values. In addition, these

Frictional resistance of adiabatic two-phase flow in narrow rectangular duct under rolling conditions

International Nuclear Information System (INIS)

Xing, Dianchuan; Yan, Changqi; Sun, Licheng; Jin, Guangyuan; Tan, Sichao

2013-01-01

Highlights: ► Two-phase flow frictional resistance in narrow duct in rolling is studied. ► Frictional resistance behaviors in rolling are divided into three regions. ► Transient frictional pressure drop fluctuates synchronously with rolling motion. ► Conventional correlations are evaluated against experimental data in rolling motion. ► New correlation for transient frictional resistance in rolling motion is developed. - Abstract: Frictional resistance of air-water two-phase flow in a narrow rectangular duct subjected to rolling motion was investigated experimentally. Time-averaged and transient frictional pressure drop under rolling condition were compared with conventional correlation in laminar flow region (Re l l ⩽ 1400) and turbulent flow region (Re l > 1400) respectively. The result shows that, despite no influence on time-averaged frictional resistance, rolling motion does induce periodical fluctuation of the pressure drop in laminar and transition flow regions. Transient frictional pressure drop fluctuates synchronously with the rolling motion both in laminar and in transition flow region, while it is nearly invariable in turbulent flow region. The fluctuation amplitude of the Relative frictional pressure gradient decreases with the increasing of the superficial velocities. Lee and Lee (2002) correlation and Chisholm (1967) correlation could satisfactorily predict time-averaged frictional pressure drop under rolling conditions, whereas poorly predict the transient frictional pressure drop when it fluctuates periodically. A new correlation with better accuracy for predicting the transient frictional pressure drop in rolling motion is achieved by modifying the Chisholm (1967) correlation on the basis of analyzing the present experimental results with a great number of data points

Pressure-induced electrical and magnetic property changes in CaCuMn6O12

International Nuclear Information System (INIS)

Zhang, W.; Yao, L.D.; Yang, L.X.; Li, F.Y.; Liu, Z.X.; Jin, C.Q.; Yu, R.C.

2006-01-01

CaCuMn 6 O 12 was prepared by using a traditional solid-state reaction method. It is a highly correlated electron system with a small gap appearing at E F and cluster glass state at low temperature, whereas temperature dependence of resistivity suggests that it is related to thermally activated nearest-neighbor hopping in paramagnetism state in higher temperature range. The resistivity decreases with increasing pressure until 11 kbar, and then increases with further increasing pressure. The blocking temperature T b goes down under pressure, indicating the suppression of cluster glass state under pressure

Safety of light-water reactor pressure vessels against brittle fracture

International Nuclear Information System (INIS)

Brumovsky, M.

1979-01-01

The results are surveyed of research by SKODA Trust into brittle failure resistance of materials for WWER type reactor pressure vessels and into pressure vessel operating safety. Conditions are discussed in detail decisive for initiation, propagation and arrest of brittle fracture. The tests on the Cr-Mo-V type steel showed high resistance of the steel to the formation and the propagation of brittle fracture. They also confirmed the high operating reliability and the required service life of the steel. (B.S.)

Complex magnetic behavior in CeGe binary alloy under pressure

International Nuclear Information System (INIS)

Marcano, N.; Haines, S.; Smith, R.; Saxena, S.S.; Aviani, I.; Espeso, J.I.; Gomez, J.S.

2007-01-01

Full text: We have investigated the effect of applied hydrostatic pressure up to 15 kbar on the magnetic structure of the antiferromagnetic CeGe by means of resistivity down to very low temperature (90 mK) and magnetization. These results are discussed together with those derived from specific heat, magnetization and resistivity obtained with different magnetic fields(1). The set of data points towards a complex structure in this compound which requires higher pressures in order to tune TN. (authors)

A method enabling simultaneous pressure and temperature measurement using a single piezoresistive MEMS pressure sensor

International Nuclear Information System (INIS)

Frantlović, Miloš; Stanković, Srđan; Jokić, Ivana; Lazić, Žarko; Smiljanić, Milče; Obradov, Marko; Vukelić, Branko; Jakšić, Zoran

2016-01-01

In this paper we present a high-performance, simple and low-cost method for simultaneous measurement of pressure and temperature using a single piezoresistive MEMS pressure sensor. The proposed measurement method utilizes the parasitic temperature sensitivity of the sensing element for both pressure measurement correction and temperature measurement. A parametric mathematical model of the sensor was established and its parameters were calculated using the obtained characterization data. Based on the model, a real-time sensor correction for both pressure and temperature measurements was implemented in a target measurement system. The proposed method was verified experimentally on a group of typical industrial-grade piezoresistive sensors. The obtained results indicate that the method enables the pressure measurement performance to exceed that of typical digital industrial pressure transmitters, achieving at the same time the temperature measurement performance comparable to industrial-grade platinum resistance temperature sensors. The presented work is directly applicable in industrial instrumentation, where it can add temperature measurement capability to the existing pressure measurement instruments, requiring little or no additional hardware, and without adverse effects on pressure measurement performance. (paper)

Pressure Dependence of Coherence-Incoherence Crossover Behavior in KFe₂As₂ Observed by Resistivity and ⁷⁵As-NMR/NQR.

Energy Technology Data Exchange (ETDEWEB)

Wiecki, P.; Taufour, V.; Chung, D. Y.; Kanatzidis, M. G.; Bud' ko, S. L.; Canfield, P. C.; Furukawa, Y.

2018-02-13

We present the results of ⁷⁵As nuclear magnetic resonance (NMR), nuclear quadrupole resonance (NQR), and resistivity measurements in KFe₂As₂ under pressure (p). The temperature dependence of the NMR shift, nuclear spin-lattice relaxation time (T1), and resistivity show a crossover between a high-temperature incoherent, local-moment behavior and a low-temperature coherent behavior at a crossover temperature (T *). T * is found to increase monotonically with pressure, consistent with increasing hybridization between localized 3d orbitalderived bands with the itinerant electron bands. No anomaly in T * is seen at the critical pressure pc = 1.8 GPa where a change of slope of the superconducting (SC) transition temperature Tc(p) has been observed. In contrast, Tc(p) seems to correlate with antiferromagnetic spin fluctuations in the normal state as measured by the NQR 1/T1 data, although such a correlation cannot be seen in the replacement effects of A in the KFe₂As₂ (A = K, Rb, Cs) family. In the superconducting state, two T1 components are observed at low temperatures, suggesting the existence of two distinct local electronic environments. The temperature dependence of the short T1s indicates a nearly gapless state below Tc. On the other hand, the temperature dependence of the long component 1/T1L implies a large reduction in the density of states at the Fermi level due to the SC gap formation. These results suggest a real-space modulation of the local SC gap structure in KFe₂As₂ under pressure.

A new insight into membrane fouling mechanism in submerged membrane bioreactor: osmotic pressure during cake layer filtration.

Science.gov (United States)

Zhang, Meijia; Peng, Wei; Chen, Jianrong; He, Yiming; Ding, Linxian; Wang, Aijun; Lin, Hongjun; Hong, Huachang; Zhang, Ye; Yu, Haiying

2013-05-15

Big gap between experimental filtration resistance of cake layer formed on membrane surface and the hydraulic resistance calculated through the Carman-Kozeny equation, suggested the existence of a new membrane fouling mechanism: osmotic pressure during cake layer filtration in SMBR system. An osmotic pressure model based on chemical potential difference was then proposed. Simulation of the model showed that osmotic pressure accounted for the major fraction of total operation pressure, and pH, applied pressure and ionic strength were the key determining factors for osmosis effect. It was found that, variations of osmotic pressure with pH, applied pressure and added ionic strength were well coincident with perditions of model's simulation, providing the first direct evidences of the real occurrence of osmosis mechanism and the feasibility of the proposed model. These findings illustrate the essential role of osmotic pressure in filtration resistance, and improve fundamental understanding on membrane fouling in SMBR systems. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effects of atmospheric pressure cold plasma on human hepatocarcinoma cell and its 5-fluorouracil resistant cell line

Energy Technology Data Exchange (ETDEWEB)

Yang, H.; Gan, L.; Yang, X., E-mail: luxinpei@hotmail.com, E-mail: yangxl@mail.hust.edu.cn [College of Life Science and Technology, Huazhong University of Science and Technology, Wuhan, Hubei 430074 (China); Lu, R. [School Hospital of Huazhong University of Science and Technology, Wuhan, Hubei 430074 (China); Xian, Y.; Lu, X., E-mail: luxinpei@hotmail.com, E-mail: yangxl@mail.hust.edu.cn [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong University of Science and Technology, Wuhan, Hubei 430074 (China)

2015-12-15

Atmospheric pressure cold plasma showed selective killing efficiency on cancer cells in vitro and in vivo, which makes plasma a potential option for cancer therapy. However, the plasma effects on chemotherapeutic drugs-resistant cells are rarely to be found. In this paper, the effects of plasma on human hepatocellular carcinoma Bel7402 cells and 5-fluorouracil (5-FU) resistant Bel7402/5FU cells were intensively investigated. The results showed that plasma induced superior toxicity to Bel7402 cells compared with Bel7402/5FU cells. Incubation with plasma-treated medium for 20 s induced more than 85% death rate in Bel7402 cells, while the same death ratio was achieved when Bel7402/5FU cells were treated for as long as 300 s. The hydrogen peroxide in the medium played a leading role in the cytotoxicity effects. Further studies implicated that when the treatment time was shorter than 60 s, the depolarization of mitochondrial membrane potential and apoptosis occurred through the intracellular reactive oxygen species accumulation in Bel7402 cells. Molecular analysis showed an increase in the transcription factor activity for AP-1, NF-kB, and p53 in Bel7402 cells. No obvious damage could be detected in plasma-treated Bel7402/5FU cells due to the strong intracellular reactive oxygen stress scavenger system.

Effects of atmospheric pressure cold plasma on human hepatocarcinoma cell and its 5-fluorouracil resistant cell line

Science.gov (United States)

Yang, H.; Lu, R.; Xian, Y.; Gan, L.; Lu, X.; Yang, X.

2015-12-01

Atmospheric pressure cold plasma showed selective killing efficiency on cancer cells in vitro and in vivo, which makes plasma a potential option for cancer therapy. However, the plasma effects on chemotherapeutic drugs-resistant cells are rarely to be found. In this paper, the effects of plasma on human hepatocellular carcinoma Bel7402 cells and 5-fluorouracil (5-FU) resistant Bel7402/5FU cells were intensively investigated. The results showed that plasma induced superior toxicity to Bel7402 cells compared with Bel7402/5FU cells. Incubation with plasma-treated medium for 20 s induced more than 85% death rate in Bel7402 cells, while the same death ratio was achieved when Bel7402/5FU cells were treated for as long as 300 s. The hydrogen peroxide in the medium played a leading role in the cytotoxicity effects. Further studies implicated that when the treatment time was shorter than 60 s, the depolarization of mitochondrial membrane potential and apoptosis occurred through the intracellular reactive oxygen species accumulation in Bel7402 cells. Molecular analysis showed an increase in the transcription factor activity for AP-1, NF-кB, and p53 in Bel7402 cells. No obvious damage could be detected in plasma-treated Bel7402/5FU cells due to the strong intracellular reactive oxygen stress scavenger system.

Resistant hypertension: an approach to management in primary care

Directory of Open Access Journals (Sweden)

Julian P Yaxley

2015-01-01

Full Text Available Hypertension is widely encountered in family medicine. Despite its prevalence, many patients have uncontrolled or difficult-to-control blood pressure. Resistant hypertension is defined as hypertension that is poorly responsive to treatment and requires the use of multiple medications to achieve acceptable blood pressure ranges. It may be a consequence of secondary hypertension or have no identifiable cause. Resistant hypertension is important to recognise because it places patients at risk of end-organ damage. Primary care physicians should be aware of the therapeutic approach for hypertension when traditional therapy fails. This article aims to familiarise readers with the evaluation and management of resistant hypertension by outlining the most recent evidence-based treatment options.

Improvement of wheel skidder tractive performance by tire inflation pressure and tire chains

OpenAIRE

Stoilov, Stanimir

2007-01-01

The motion resistance ratio, gross traction ratio and net traction ratio of a wheel cable skidder were determined and mathematical models derived for three tire inflation pressure values with or without tire chains on forest road in mountainous conditions. The motion resistance ratio increases with the increase of tire inflation pressure. On the contrary, the gross traction ratio increases with the decrease of tire inflation pressure. However, when the tires are equipped with tire chains t...

A low-carbohydrate/high-fat diet reduces blood pressure in spontaneously hypertensive rats without deleterious changes in insulin resistance.

Science.gov (United States)

Bosse, John D; Lin, Han Yi; Sloan, Crystal; Zhang, Quan-Jiang; Abel, E Dale; Pereira, Troy J; Dolinsky, Vernon W; Symons, J David; Jalili, Thunder

2013-06-15

Previous studies reported that diets high in simple carbohydrates could increase blood pressure in rodents. We hypothesized that the converse, a low-carbohydrate/high-fat diet, might reduce blood pressure. Six-week-old spontaneously hypertensive rats (SHR; n = 54) and Wistar-Kyoto rats (WKY; n = 53, normotensive control) were fed either a control diet (C; 10% fat, 70% carbohydrate, 20% protein) or a low-carbohydrate/high-fat diet (HF; 20% carbohydrate, 60% fat, 20% protein). After 10 wk, SHR-HF had lower (P vs. 159 ± 3 mmHg) but a similar degree of cardiac hypertrophy (33.4 ± 0.4 vs. 33.1 ± 0.4 heart weight/tibia length, mg/mm). Mesenteric arteries and the entire aorta were used to assess vascular function and endothelial nitric oxide synthase (eNOS) signaling, respectively. Endothelium-dependent (acetylcholine) relaxation of mesenteric arteries was improved (P vs. SHR-C, whereas contraction (potassium chloride, phenylephrine) was reduced (P vs. SHR-C. Plasma glucose, insulin, and homoeostatic model of insulin assessment were lower (P vs. SHR-C, whereas peripheral insulin sensitivity (insulin tolerance test) was similar. After a 10-h fast, insulin stimulation (2 U/kg ip) increased (P vs. SHR-HF. In conclusion, a low-carbohydrate/high-fat diet reduced blood pressure and improved arterial function in SHR without producing signs of insulin resistance or altering insulin-mediated signaling in the heart, skeletal muscle, or vasculature.

An innovative technique for estimating water saturation from capillary pressure in clastic reservoirs

Science.gov (United States)

Adeoti, Lukumon; Ayolabi, Elijah Adebowale; James, Logan

2017-11-01

A major drawback of old resistivity tools is the poor vertical resolution and estimation of hydrocarbon when applying water saturation (Sw) from historical resistivity method. In this study, we have provided an alternative method called saturation height function to estimate hydrocarbon in some clastic reservoirs in the Niger Delta. The saturation height function was derived from pseudo capillary pressure curves generated using modern wells with complete log data. Our method was based on the determination of rock type from log derived porosity-permeability relationship, supported by volume of shale for its classification into different zones. Leverette-J functions were derived for each rock type. Our results show good correlation between Sw from resistivity based method and Sw from pseudo capillary pressure curves in wells with modern log data. The resistivity based model overestimates Sw in some wells while Sw from the pseudo capillary pressure curves validates and predicts more accurate Sw. In addition, the result of Sw from pseudo capillary pressure curves replaces that of resistivity based model in a well where the resistivity equipment failed. The plot of hydrocarbon pore volume (HCPV) from J-function against HCPV from Archie shows that wells with high HCPV have high sand qualities and vice versa. This was further used to predict the geometry of stratigraphic units. The model presented here freshly addresses the gap in the estimation of Sw and is applicable to reservoirs of similar rock type in other frontier basins worldwide.

Role of the Kidneys in Resistant Hypertension

Directory of Open Access Journals (Sweden)

Z. Khawaja

2011-01-01

Full Text Available Resistant hypertension is a failure to achieve goal BP (<140/90 mm Hg for the overall population and <130/80 mm Hg for those with diabetes mellitus or chronic kidney disease in a patient who adheres to maximum tolerated doses of 3 antihypertensive drugs including a diuretic. The kidneys play a critical role in long-term regulation of blood pressure. Blunted pressure natriuresis, with resultant increase in extracellular fluid volume, is an important cause of resistant hypertension. Activation of the renin-angiotensin-aldosterone system, increased renal sympathetic nervous system activity and increased sodium reabsorption are important renal mechanisms. Successful treatment requires identification and reversal of lifestyle factors or drugs contributing to treatment resistance, diagnosis and appropriate treatment of secondary causes of hypertension, use of effective multidrug regimens and optimization of diuretic therapy. Since inappropriate renal salt retention underlies most cases of drug-resistant hypertension, the therapeutic focus should be on improving salt depleting therapy by assessing and, if necessary, reducing dietary salt intake, optimizing diuretic therapy, and adding a mineralocorticoid antagonist if there are no contraindications.

Predicting spring barley yield from variety-specific yield potential, disease resistance and straw length, and from environment-specific disease loads and weed pressure

DEFF Research Database (Denmark)

Østergård, Hanne; Kristensen, Kristian; Pinnschmidt, Hans O.

2008-01-01

For low-input crop production, well-characterised varieties increase the possibilities of managing diseases and weeds. This analysis aims at developing a framework for analyzing grain yield using external varietal information about disease resistance, weed competitiveness and yield potential and ...... growth habit. Higher grain yield was thus predicted for taller plants under weed pressure. The results are discussed in relation to the model framework, impact of the considered traits and use of information from conventional variety testing in organic cropping systems....

Renal Denervation vs. Spironolactone in Resistant Hypertension: Effects on Circadian Patterns and Blood Pressure Variability.

Science.gov (United States)

de la Sierra, Alejandro; Pareja, Julia; Armario, Pedro; Barrera, Ángela; Yun, Sergi; Vázquez, Susana; Sans, Laia; Pascual, Julio; Oliveras, Anna

2017-01-01

Sympathetic renal denervation (SRD) has been proposed as a therapeutic alternative for patients with resistant hypertension not controlled on pharmacological therapy. Two studies have suggested an effect of SRD in reducing short-term blood pressure variability (BPV). However, this has not been addressed in a randomized comparative trial. We aimed to compare the effects of spironolactone and SRD on circadian BP and BPV. This is a post-hoc analysis of a randomized trial in 24 true resistant hypertensive patients (15 men, 9 women; mean age 64 years) comparing 50mg of spironolactone (n = 13) vs. SRD (n = 11) on 24-hour BP. We report here the comparative effects on daytime (8 am-10 pm) and nighttime (0 am-6 am) BP, night-to-day ratios and BP and heart rate variabilities (SD and coefficient of variation of 24-hour, day and night, as well as weighted SD and average real variability (ARV)). Spironolactone was more effective than SRD in reducing daytime systolic (P = 0.006), daytime diastolic (P = 0.006), and nighttime systolic (P = 0.050) BP. No differences were observed in the night-to-day ratios. In contrast, SRD-reduced diastolic BPV (24 hours, daytime, nighttime, weighted, and ARV; all P < 0.05) with respect to spironolactone, without significant differences in systolic BPV. Spironolactone is more effective than SRD in reducing ambulatory BP. However, BPV is significantly more reduced with SRD. This effect could be important in terms of potential prevention beyond BP reduction and deserves further investigation. © American Journal of Hypertension, Ltd 2016. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

A technique for precise electrical-transport measurements under pressure above 10 GPa

Energy Technology Data Exchange (ETDEWEB)

Ohashi, M [Division of Civil and Enviromental Engineering, Kanazawa University, Kakuma-machi, Kanazawa 920-1192 (Japan)], E-mail: ohashi@t.kanazawa-u.ac.jp

2008-07-15

We report a technique for the precise measurement of electrical resistivity at high pressures up to 15 GPa by using Bridgman anvils. The relatively large size of the pressure chamber (1.0 mm in diameter) allows the use of large specimens and simple experimental procedures rather than using a standard diamond anvil cell. A SUS310 gasket is pressed by two tungsten carbide anvils. A sample with typical dimensions of approximately 0.5x0.2x0.1mm{sup 3} is placed in a small hole of the gasket. In order to obtain a quasi-hydrostatic pressure, the pressure chamber is filled with a 1:1 mixture of Fluorinert FC70 and FC77 as the pressure transmitting medium. Electrical leads are introduced through shallow grooves milled into the anvil. The grooves are filled with a mixture of alumina powder for insulation. Accurate data of the resistance values of Bi and Fe at room temperature are available. We observe sharp transitions for Bi at 2.55, 2.7 and 7.7 GPa. The electrical resistance of Fe shows a sudden increase due to a structural transition near 14 GPa.

Normal mode analysis for linear resistive magnetohydrodynamics

International Nuclear Information System (INIS)

Kerner, W.; Lerbinger, K.; Gruber, R.; Tsunematsu, T.

1984-10-01

The compressible, resistive MHD equations are linearized around an equilibrium with cylindrical symmetry and solved numerically as a complex eigenvalue problem. This normal mode code allows to solve for very small resistivity eta proportional 10 -10 . The scaling of growthrates and layer width agrees very well with analytical theory. Especially, both the influence of current and pressure on the instabilities is studied in detail; the effect of resistivity on the ideally unstable internal kink is analyzed. (orig.)

Pressure-Sensitive Resistor Material

Science.gov (United States)

Du Fresne, E. R.

1986-01-01

Low-conductivity particles in rubber offer wide dynamic range. Sensor consists of particles of relatively low conductivity embedded in rubber. Resistance of sensor decreases by about 100 times as pressure on it increases from zero to 0.8 MN/M to the second power. Resistor promising candidate as tactile sensor for robots and remote manipulators.

Pressure and temperature induced electrical resistance change in nano-carbon/epoxy composites

NARCIS (Netherlands)

Shen, J. T.; Buschhorn, S. T.; De Hosson, J. Th. M.; Schulte, K.; Fiedler, B.

2015-01-01

In this study, we investigate the changes of electrical resistance of the carbon black (CB) and carbon nanotube (CNT) filled epoxy composites upon compression, swelling and temperature variation. For all samples we observe a decrease of electrical resistance under compression, while an increase of

Inactivation of Escherichia coli in broth and sausage by combined high pressure and Lactobacillus casei cell extract.

Science.gov (United States)

Chung, Hyun-Jung; Yousef, Ahmed E

2010-10-01

The purpose of this study was to investigate the effect of combined high pressure and Lactobacillus casei cell extract (CE) on Escherichia coli O157 strains with variation in pressure resistance in broth and sausage. Pressure-resistant (O157:H7 and O157:H12) and -sensitive (O157-M1 and O157-M2) E. coli strains were used. Pressure treatment at 350 MPa for 20 min in broth caused 1.1-1.2 logs reduction in O157:H12 and O157:H7 and 4.1-5.5 logs reduction in the O157-M1 and O157-M2. When high pressure was treated in the presence of CE (32 CEAU/mL), the combination treatment caused a significant inactivation in the pressure-resistant O157:H7 strains resulting in the viability loss of 4.3-4.6 logs and the synergistic effect increased with increase in treatment time (p casei CE may cause considerable damage to cellular components of E. coli during the high pressure treatment. The synergy between high pressure processing and Lb. casei OSY-LB6A CE against pressure-resistant E. coli O157 strains suggests the feasibility of using this combination to minimize the risk of transmission of E. coli O157 by food.

Resistant Hypertension, Time-Updated Blood Pressure Values and Renal Outcome in Type 2 Diabetes Mellitus.

Science.gov (United States)

Viazzi, Francesca; Piscitelli, Pamela; Ceriello, Antonio; Fioretto, Paola; Giorda, Carlo; Guida, Pietro; Russo, Giuseppina; De Cosmo, Salvatore; Pontremoli, Roberto

2017-09-22

Apparent treatment resistant hypertension (aTRH) is highly prevalent in patients with type 2 diabetes mellitus (T2D) and entails worse cardiovascular prognosis. The impact of aTRH and long-term achievement of recommended blood pressure (BP) values on renal outcome remains largely unknown. We assessed the role of aTRH and BP on the development of chronic kidney disease in patients with T2D and hypertension in real-life clinical practice. Clinical records from a total of 29 923 patients with T2D and hypertension, with normal baseline estimated glomerular filtration rate and regular visits during a 4-year follow-up, were retrieved and analyzed. The association between time-updated BP control (ie, 75% of visits with BP hypertension. BP control is not associated with a more-favorable renal outcome in aTRH. The relationship between time-updated BP and renal function seems to be J-shaped, with optimal systolic BP values between 120 and 140 mm Hg. © 2017 The Authors. Published on behalf of the American Heart Association, Inc., by Wiley.

Transport properties of Heusler Compound Mn3Si under high pressure

International Nuclear Information System (INIS)

Takaesu, Y; Uchima, K; Nakamura, S; Yogi, M; Niki, H; Hedo, M; Nakama, T; Tomiyoshi, S

2014-01-01

The electrical resistivity ρ and the thermopower S of the single crystalline sample of the Heusler compound Mn 3 Si have been measured in the temperature range between 2 and 300 K under high pressures up to 2.2 GPa. The temperature variations of ρ and S indicate the characteristic features at the Néel temperature T N . An additional anomaly in S(T), related to the 3Q satellites in SDW, is observed at P > 1 GPa, and it disappears at P > 1 GPa. The Néel temperature, obtained from ρ(T) and S(T) curves, increases with increasing pressure. The pressure dependences of the residual resistivity and the thermopower at T = 2 K show the discontinuous changes at P ≈ 1 GPa, indicating a pressure induced phase transition

Development and evaluation of a HEPA filter for increased strength and resistance to elevated temperature

International Nuclear Information System (INIS)

Gilbert, H.; Bergman, W.; Fretthold, J.K.

1992-01-01

We have developed an improved HEPA filter for increased strength and resistance to elevated temperature to improve the reliability of HEPA filters under accident conditions. The improvements to the HEPA filter consist of a silicone rubber sealant and a new HEPA medium reinforced with a glass cloth. Several prototype filters were built and evaluated for temperature and pressure resistance and resistance to rough handling. The temperature resistance test consisted of exposing the HEPA filter to 1,000 scan at 700 degrees F for five minutes. The pressure resistance test consisted of exposing the HEPA filter to a differential pressure of 10 in. w.g. using a water saturated air flow at 95 degrees F. For the rough handling test, we used a vibrating machine designated the Q110. DOP filter efficiency tests were performed before and after each of the environmental tests. In addition to following the standard practice of using a separate new filter for each environmental test, we also subjected the same filter to the elevated temperature test followed by the pressure resistance test. The efficiency test results show that the improved HEPA filter is significantly better than the standard HEPA filter

Diastolic pressure underestimates age-related hemodynamic impairment.

Science.gov (United States)

Galarza, C R; Alfie, J; Waisman, G D; Mayorga, L M; Cámera, L A; del Río, M; Vasvari, F; Limansky, R; Farías, J; Tessler, J; Cámera, M I

1997-10-01

It has been hypothesized that as large arteries become more rigid with age, the pattern of hypertension changes from diastolic to systolic. Thus, diastolic blood pressure (DBP) may lose its ability to reflect the increase in vascular resistance with age. To assess this, we studied the age-related changes in blood pressure pattern and its steady-state and pulsatile determinants. We performed an epidemiological analysis based on a national survey of 10,462 subjects from Argentina. A hemodynamic analysis (impedance cardiography) was then carried out in 636 consecutive hypertensive patients (age, 25 to 74 years). Whereas the rate of increment in the prevalence of mild to moderate hypertension (MMH) reached a plateau after the sixth decade, isolated and borderline systolic forms of hypertension began a steep and sustained rise. Among patients with MMH, DBP remained stable from the third to the seventh decade, whereas SBP maintained a sustained increase. Despite similar DBP, the systemic vascular resistance index increased 47% (P<.01) and the cardiac index decreased 27% (P<.01), whereas the ratio of stroke volume to pulse pressure, an index of arterial compliance, decreased 45% (P<.01). However, there were no significant differences between older patients with MMH and those with isolated systolic hypertension in the level of SBP, vascular resistance, stroke volume, and cardiac index. Compared with age-matched normotensive control subjects, the ratio of stroke volume to pulse pressure was much more reduced in isolated systolic hypertension (48%) than in MMH (30%). In summary, the present study, carried out in a large sample of hypertensive subjects with a wide age range, showed a simultaneous impairment in vascular resistance and arterial compliance associated with aging in different patterns of hypertension. The magnitude of these changes, with opposite effects on DBP but additive effects on SBP, suggests that a hemodynamic mechanism could determine the transition in the

Carbon resistor pressure gauge calibration at low stresses

International Nuclear Information System (INIS)

Cunningham, Bruce; Vandersall, Kevin S.; Niles, Angela M.; Greenwood, Daniel W.; Garcia, Frank; Forbes, Jerry W.; Wilson, William H.

2002-01-01

The 470 Ohm carbon resistor gauge has been used in the stress range up to 4-5 GPa for highly heterogeneous materials and/or divergent flow experiments. The attractiveness of the gauge is its rugged nature, simple construction, low cost, reproducibility, and survivability in dynamic events. Gauge drawbacks are the long time response to pressure equilibration and gauge resistance hysteresis. In the regime below 0.4 GPa, gauge calibration has been extrapolated. Because of the need for calibration data within this low stress regime, calibration experiments were performed using a split-Hopkinson bar, drop tower apparatus, and gas pressure chamber. Since the performance of the gauge at elevated temperatures is a concern, the change in resistance due to heating at atmospheric pressure was also investigated. Details of the various calibration arrangements and the results are discussed and compared to a calibration curve fit to previously published calibration data

Effect of Environmental Variables on the Flammability of Fire Resistant Materials

OpenAIRE

Osorio, Andres Felipe

2014-01-01

This work investigates the effects of external radiation, ambient pressure and microgravity on the flammability limits of fire-resistant (FR) materials. Future space missions may require spacecraft cabin environments different than those used in the International Space Station, 21%O2, 101.3kPa. Environmental variables include flow velocity, oxygen concentration, ambient pressure, micro or partial-gravity, orientation, presence of an external radiant flux, etc. Fire-resistant materials are use...

Apparent and true resistant hypertension: definition, prevalence and outcomes

OpenAIRE

Judd, E; Calhoun, DA

2014-01-01

Resistant hypertension, defined as blood pressure (BP) remaining above goal despite the use of ≥3 antihypertensive medications at maximally tolerated doses (one ideally being a diuretic) or BP that requires ≥4 agents to achieve control, has received more attention with increased efforts to improve BP control rates and the emergence of device-based therapies for hypertension. This classically defined resistant group consists of patients with true resistant hypertension, controlled resistant hy...

Phase transformation and conductivity in nanocrystal PbS under pressure

DEFF Research Database (Denmark)

Jiang, Jianzhong; Gerward, Leif; Secco, R.

2000-01-01

The grain-size effect on the phase transition induced by pressure in PbS was studied by in situ high-pressure electrical resistance and synchrotron radiation x-ray powder diffraction measurements. The mean transition pressure of the B1-to-B16 phase transformation was found to be 6.3±1.3 GPa in 8...... in terms of a decrease of energy band gap with increasing pressure. ©2000 American Institute of Physics....

Effects of exercise intensity and creatine loading on post-resistance exercise hypotension

Directory of Open Access Journals (Sweden)

Moreno Rodrigues Moreno

2009-09-01

Full Text Available Postexercise hypotension plays an important role in the non-pharmacological treat-ment of hypertension and is characterized by a decrease in blood pressure after a single exercise bout in relation to pre-exercise levels. This study investigated the effects of exercise intensity and creatine monohydrate supplementation on postexercise hypotension, as well as the possible role of blood lactate in this response. Ten normotensive subjects underwent resistance exercise sessions before (BC and after (AC creatine supplementation: 1 muscle endurance (ME consisting of 30 repetitions at 30% of one-repetition maximum; 2 hypertrophy (HP consisting of 8 repetitions at 75% of one-repetition maximum. Blood pressure was measured before and after the exercise bout. Blood lactate was measured after the exercise bout. The HP and ME sessions promoted a decrease in systolic blood pressure (∆ -19 ± 1.0 mmHg; ∆ -15 ± 0.9 mmHg, respectively, P 0.05. In conclusion, resistance exercise intensity did not influence postexercise hypotension. Creatine supplementation attenuated the decrease in blood pressure after resistance exercise. The results suggest the involvement of blood lactate in post-resistance exercise hypotension.

Effects of exercise intensity and creatine loading on post-resistance exercise hypotension

Directory of Open Access Journals (Sweden)

Moreno Rodrigues Moreno

2009-01-01

Postexercise hypotension plays an important role in the non-pharmacological treat-ment of hypertension and is characterized by a decrease in blood pressure after a single exercise bout in relation to pre-exercise levels. This study investigated the effects of exercise intensity and creatine monohydrate supplementation on postexercise hypotension, as well as the possible role of blood lactate in this response. Ten normotensive subjects underwent resistance exercise sessions before (BC and after (AC creatine supplementation: 1 muscle endurance (ME consisting of 30 repetitions at 30% of one-repetition maximum; 2 hypertrophy (HP consisting of 8 repetitions at 75% of one-repetition maximum. Blood pressure was measured before and after the exercise bout. Blood lactate was measured after the exercise bout. The HP and ME sessions promoted a decrease in systolic blood pressure (∆ -19 ± 1.0 mmHg; ∆ -15 ± 0.9 mmHg, respectively, P 0.05. In conclusion, resistance exercise intensity did not influence postexercise hypotension. Creatine supplementation attenuated the decrease in blood pressure after resistance exercise. The results suggest the involvement of blood lactate in post-resistance exercise hypotension.

Effect of whole body resistance training on arterial compliance in young men.

Science.gov (United States)

Rakobowchuk, M; McGowan, C L; de Groot, P C; Bruinsma, D; Hartman, J W; Phillips, S M; MacDonald, M J

2005-07-01

The effect of resistance training on arterial stiffening is controversial. We tested the hypothesis that resistance training would not alter central arterial compliance. Young healthy men (age, 23 +/- 3.9 (mean +/- s.e.m.) years; n = 28,) were whole-body resistance trained five times a week for 12 weeks, using a rotating 3-day split-body routine. Resting brachial blood pressure (BP), carotid pulse pressure, carotid cross-sectional compliance (CSC), carotid initima-media thickness (IMT) and left ventricular dimensions were evaluated before beginning exercise (PRE), after 6 weeks of exercise (MID) and at the end of 12 weeks of exercise (POST). CSC was measured using the pressure-sonography method. Results indicate reductions in brachial (61.1 +/- 1.4 versus 57.6 +/- 1.2 mmHg; P training and the mechanisms responsible for cardiac hypertrophy and reduced arterial compliance are either not inherent to all resistance-training programmes or may require a prolonged stimulus.

Non-linear pressure/temperature-dependence of high pressure thermal inactivation of proteolytic Clostridium botulinum type B in foods.

Directory of Open Access Journals (Sweden)

Maximilian B Maier

Full Text Available The effect of high pressure thermal (HPT processing on the inactivation of spores of proteolytic type B Clostridium botulinum TMW 2.357 in four differently composed low-acid foods (green peas with ham, steamed sole, vegetable soup, braised veal was studied in an industrially feasible pressure range and temperatures between 100 and 120°C. Inactivation curves exhibited rapid inactivation during compression and decompression followed by strong tailing effects. The highest inactivation (approx. 6-log cycle reduction was obtained in braised veal at 600 MPa and 110°C after 300 s pressure-holding time. In general, inactivation curves exhibited similar negative exponential shapes, but maximum achievable inactivation levels were lower in foods with higher fat contents. At high treatment temperatures, spore inactivation was more effective at lower pressure levels (300 vs. 600 MPa, which indicates a non-linear pressure/temperature-dependence of the HPT spore inactivation efficiency. A comparison of spore inactivation levels achievable using HPT treatments versus a conventional heat sterilization treatment (121.1°C, 3 min illustrates the potential of combining high pressures and temperatures to replace conventional retorting with the possibility to reduce the process temperature or shorten the processing time. Finally, experiments using varying spore inoculation levels suggested the presence of a resistant fraction comprising approximately 0.01% of a spore population as reason for the pronounced tailing effects in survivor curves. The loss of the high resistance properties upon cultivation indicates that those differences develop during sporulation and are not linked to permanent modifications at the genetic level.

Computer model analysis of the radial artery pressure waveform.

Science.gov (United States)

Schwid, H A; Taylor, L A; Smith, N T

1987-10-01

Simultaneous measurements of aortic and radial artery pressures are reviewed, and a model of the cardiovascular system is presented. The model is based on resonant networks for the aorta and axillo-brachial-radial arterial system. The model chosen is a simple one, in order to make interpretation of the observed relationships clear. Despite its simplicity, the model produces realistic aortic and radial artery pressure waveforms. It demonstrates that the resonant properties of the arterial wall significantly alter the pressure waveform as it is propagated from the aorta to the radial artery. Although the mean and end-diastolic radial pressures are usually accurate estimates of the corresponding aortic pressures, the systolic pressure at the radial artery is often much higher than that of the aorta due to overshoot caused by the resonant behavior of the radial artery. The radial artery dicrotic notch is predominantly dependent on the axillo-brachial-radial arterial wall properties, rather than on the aortic valve or peripheral resistance. Hence the use of the radial artery dicrotic notch as an estimate of end systole is unreliable. The rate of systolic upstroke, dP/dt, of the radial artery waveform is a function of many factors, making it difficult to interpret. The radial artery waveform usually provides accurate estimates for mean and diastolic aortic pressures; for all other measurements it is an inadequate substitute for the aortic pressure waveform. In the presence of low forearm peripheral resistance the mean radial artery pressure may significantly underestimate the mean aortic pressure, as explained by a voltage divider model.

An optimal method for generating stable vancomycin heteroresistance and intermediate susceptibility in methicillin-resistant Staphylococcus aureusblood isolates under in-vitro vancomycin pressure

Directory of Open Access Journals (Sweden)

Riad Khatib

2012-12-01

Full Text Available Objectives: The relevance of vancomycin intermediately-susceptible (VISA and hetero-resistant (hVISA methicillin-resistantStaphylococcus aureus (MRSA remains uncertain because of their low frequency. In vitro attempts to generate reducedsusceptibility have been inconsistent. We describe a simple method for generating VISA/hVISA.Materials and methods: Twenty-four SCCmec type II and IV MRSA blood isolates plus USA100 and USA300 controls werecultured (107 CFU/ml in BHI broth with 0, 2 and 3 mg/L vancomycin for 10 days followed by 10 days vancomycin-freepassage.We monitored vancomycin minimum inhibitory concentration (MIC; Etest and population analysis profile-areaunder the curve (PAP-AUC ratios of tested isolate-Mu3 during and after vancomycin pressure (VP. PAP-AUC ratios 1.3 were considered consistent with susceptible, hVISA and VISA, respectively.Results: VP at 2 mg/L (VP-2 increased MIC to 3 mg/L in 20 (83.3% isolates and raised PAP-AUC ratio to hVISA (n=18; 75.0%and VISA (six; 25.0% ranges. VP-3 increased MIC to 3 and 4 mg/L in 19 (79.2% and three (12.5% isolates, respectively andraised PAP-AUC ratio to hVISA (n=3; 12.5% and VISA (n=19; 79.2% ranges. SCCmec IV isolates had lower pre-exposurePAP-AUC ratios (0.48±0.14 vs. 0.69±0.10; p<0.001 and lower MIC (1.6±0.2 vs. 1.8±0.2 mg/L; p=0.1 but MIC rise and VISA/hVISA emergence was comparable. MIC and PAP-AUC ratio rises were stable in 20/22 isolates during drug-free passages.Conclusions: VISA/hVISA readily emerges among MRSA SCCmec type II and IV isolates under VP. VP at the MIC level generateshVISA while pressure at slightly higher level results in the VISA phenotype. J Microbiol Infect Dis 2012; 2(4: 129-134Key words: Staphylococcus aureus; heteroresistance; glycopeptides; resistance; bacteremia.

Effects of process parameters on sheet resistance uniformity of fluorine-doped tin oxide thin films

Science.gov (United States)

Hudaya, Chairul; Park, Ji Hun; Lee, Joong Kee

2012-01-01

An alternative indium-free material for transparent conducting oxides of fluorine-doped tin oxide [FTO] thin films deposited on polyethylene terephthalate [PET] was prepared by electron cyclotron resonance - metal organic chemical vapor deposition [ECR-MOCVD]. One of the essential issues regarding metal oxide film deposition is the sheet resistance uniformity of the film. Variations in process parameters, in this case, working and bubbler pressures of ECR-MOCVD, can lead to a change in resistance uniformity. Both the optical transmittance and electrical resistance uniformity of FTO film-coated PET were investigated. The result shows that sheet resistance uniformity and the transmittance of the film are affected significantly by the changes in bubbler pressure but are less influenced by the working pressure of the ECR-MOCVD system.

Computerized reactor pressure vessel materials information system

International Nuclear Information System (INIS)

Strosnider, J.; Monserrate, C.; Kenworthy, L.D.; Tether, C.D.

1980-10-01

A computerized information system for storage and retrieval of reactor pressure vessel materials data was established, as part of Task Action Plan A-11, Reactor Vessel Materials Toughness. Data stored in the system are necessary for evaluating the resistance of reactor pressure vessels to flaw-induced fracture. This report includes (1) a description of the information system; (2) guidance on accessing the system; and (3) a user's manual for the system

High pressure study of Pu{sub 0.92}Am{sub 0.08} binary alloy

Energy Technology Data Exchange (ETDEWEB)

Klosek, V; Faure, P; Genestier, C [CEA, Valduc, F-21120 Is-sur-Tille (France); Griveau, J C; Wastin, F [European Commission JRC, Institute for Transuranium Elements, Postfach 2340, D-76125 Karlsruhe (Germany); Baclet, N [CEA, DRT/DTMN, F-38054 Grenoble (France)], E-mail: vincent.klosek@cea.fr

2008-07-09

The phase transitions (by means of x-ray diffraction) and electrical resistivity of a Pu{sub 0.92}Am{sub 0.08} binary alloy were determined under pressure (up to 2 GPa). The evolution of atomic volume with pressure gives detailed information concerning the degree of localization of 5f electronic states and their delocalization process. A quasi-linear V = f(P) dependence reflects subtle modifications of the electronic structure when P increases. The electrical resistivity measurements reveal the very high stability of the {delta} phase for pressures less than 0.7 GPa, since no martensitic-like transformation occurs at low temperature. Remarkable electronic behaviours have also been observed. Finally, resistivity curves have shown the temperature dependence of the phase transformations together with unexpected kinetic effects.

Simulation of the behavior of pressurized underwater concrete

Directory of Open Access Journals (Sweden)

Ashraf Mohamed Heniegal

2015-06-01

Full Text Available Under-Water Concrete (UWC contains Anti-Washout Admixtures (AWA (0.0%, 0.2%, 0.3%, 0.4% and 0.5% by weight of cement with cement contents (400, 450, 500 and 550 kg/m3. All concrete mix contains silica fume and high-range water reducing (15% and 4% respectively by weight of cement. The fine to steel slag coarse aggregate was 1:1. The concrete mix was tested for slump, slump flow, compressive strength and washout resistance using two test methods based on different principles. The first method is the plunge test CRDC61 which is widely used in North America, and the second method is the pressurized air tube which has been manufactured for this research and developed to simulate the effect of water pressure on washout resistance of underwater mix. The results of compressive strength test were compared to concrete cast underwater with that cast in air. Test results indicated that the use of an AWA facilitates the production of UWC mix with the added benefit of lower washout resistance. New technique of simulating pressurized UWC is reliable for detecting UWC properties. Adding AWA (0.3–0.5% by weight of cement makes all mix acceptable according to Japanese Society of Civil Engineers.

correlations between antibiotic intake and resistance of some enteric ...

African Journals Online (AJOL)

DJFLEX

2010-06-25

Jun 25, 2010 ... Bacterial resistance to antibiotics has been attributed to many different factors with emphasis on the widespread use, misuse or overuse of antibiotics. Current thinking has referenced these as providing the selective pressure favouring propagation of resistant organisms (Livermore, 2003). This, however ...

Susceptibility to social pressure following ventromedial prefrontal cortex damage.

Science.gov (United States)

Chen, Kuan-Hua; Rusch, Michelle L; Dawson, Jeffrey D; Rizzo, Matthew; Anderson, Steven W

2015-11-01

Social pressure influences human behavior including risk taking, but the psychological and neural underpinnings of this process are not well understood. We used the human lesion method to probe the role of ventromedial prefrontal cortex (vmPFC) in resisting adverse social pressure in the presence of risk. Thirty-seven participants (11 with vmPFC damage, 12 with brain damage outside the vmPFC and 14 without brain damage) were tested in driving simulator scenarios requiring left-turn decisions across oncoming traffic with varying time gaps between the oncoming vehicles. Social pressure was applied by a virtual driver who honked aggressively from behind. Participants with vmPFC damage were more likely to select smaller and potentially unsafe gaps under social pressure, while gap selection by the comparison groups did not change under social pressure. Participants with vmPFC damage also showed prolonged elevated skin conductance responses (SCR) under social pressure. Comparison groups showed similar initial elevated SCR, which then declined prior to making left-turn decisions. The findings suggest that the vmPFC plays an important role in resisting explicit and immediately present social pressure with potentially negative consequences. The vmPFC appears to contribute to the regulation of emotional responses and the modulation of decision making to optimize long-term outcomes. © The Author (2015). Published by Oxford University Press. For Permissions, please email: journals.permissions@oup.com.

Basic design of radiation-resistant LVDTs: Linear Variable Differential Transformer

Energy Technology Data Exchange (ETDEWEB)

Sohn, J. M.; Park, S. J.; Kang, Y. H. (and others)

2008-02-15

A LVDT(Linear Variable Differential Transformer) for measuring the pressure level was used to measure the pressure of a nuclear fuel rod during the neutron irradiation test in a research reactor. A LVDT for measuring the elongation was also used to measure the elongation of nuclear fuels, and the creep and fatigue of materials during a neutron irradiation test in a research reactor. In this report, the basic design of two radiation-resistant LVDTs for measuring the pressure level and elongation are described. These LVDTs are used a under radiation environment such as a research reactor. In the basic design step, we analyzed the domestic and foreign technical status for radiation-resistant LVDTs, made part and assembly drawings and established simple procedures for their assembling. Only a few companies in the world can produce radiation-resistant LVDTs. Not only these are extremely expensive, but the prices are continuously rising. Also, it takes a long time to procure a LVDT, as it can only be bought about by an order-production. The localization of radiation-resistant LVDTs is necessary in order to provide them quickly and at a low cost. These radiation-resistant LVDTs will be used at neutron irradiation devices such as instrumented fuel capsules, special purpose capsules and a fuel test loop in research reactors. We expect that the use of neutron irradiation tests will be revitalized by the localization of radiation-resistant LVDTs.

Control of nasal vasculature and airflow resistance in the dog.

Science.gov (United States)

Lung, M A; Phipps, R J; Wang, J C; Widdicombe, J G

1984-01-01

Nasal vascular and airflow resistances have been measured in dogs, simultaneously on both sides separately. Vascular resistance was measured either by constant flow perfusion of the terminal branch of the maxillary artery (which supplies, via the sphenopalatine artery, the nasal septum, most of the turbinates and the nasal sinuses) or by measuring blood flow through this artery, maintained by the dog's own blood pressure. Airflow resistance was assessed by inserting balloon-tipped endotracheal catheters into the back of each nasal cavity via the nasopharynx, and measuring transnasal pressure at constant airflow through each side of the nose simultaneously. Preliminary experiments indicated that there was 5-10% collateral anastomosis between the two sides. Close-arterial injection of drugs showed different patterns of response. Adrenaline, phenylephrine, chlorpheniramine and low doses of prostaglandin F2 alpha increased vascular resistance and lowered airway resistance. Salbutamol, methacholine and histamine lowered vascular resistance and increased airway resistance. Dobutamine decreased airway resistance with a small increase in vascular resistance. Prostaglandins E1, E2 and F2 alpha (high dose) decreased both vascular and airway resistances. Substance P, eledoisin-related peptide and vasoactive intestinal polypeptide lowered vascular resistance with little change in airway resistance. The results are interpreted in terms of possible drug actions on precapillary resistance vessels, sinusoids and venules, and arteriovenous anastomoses. It is concluded that nasal airway resistance cannot be correlated with vascular resistance or blood flow, since the latter has a complex and ill-defined relationship with nasal vascular blood volume. PMID:6204040

A change of electronic state tuned by pressure: pressure-induced superconductivity of the antiferromagnet Ce{sub 2}Ni{sub 3}Ge{sub 5}

Energy Technology Data Exchange (ETDEWEB)

Nakashima, M [Graduate School of Science, Osaka University, Toyonaka, Osaka 560-0043 (Japan); Research Center for Materials Science at Extreme Conditions, Osaka University, Toyonaka, Osaka 560-8531 (Japan); Kohara, H [Graduate School of Science, Osaka University, Toyonaka, Osaka 560-0043 (Japan); Thamizhavel, A [Graduate School of Science, Osaka University, Toyonaka, Osaka 560-0043 (Japan); Matsuda, T D [Advanced Science and Industrial Research Center, Japan Atomic Energy Research Institute, Tokai, Ibaraki 319-1195 (Japan); Haga, Y [Advanced Science and Industrial Research Center, Japan Atomic Energy Research Institute, Tokai, Ibaraki 319-1195 (Japan); Hedo, M [Institute for Solid State Physics, University of Tokyo, Kashiwa, Chiba 277-8581 (Japan); Uwatoko, Y [Institute for Solid State Physics, University of Tokyo, Kashiwa, Chiba 277-8581 (Japan); Settai, R [Graduate School of Science, Osaka University, Toyonaka, Osaka 560-0043 (Japan); Onuki, Y [Graduate School of Science, Osaka University, Toyonaka, Osaka 560-0043 (Japan); Advanced Science and Industrial Research Center, Japan Atomic Energy Research Institute, Tokai, Ibaraki 319-1195 (Japan)

2005-07-20

We measured the electrical resistivity of an antiferromagnet Ce{sub 2}Ni{sub 3}Ge{sub 5} with the orthorhombic crystal structure under pressure. The Neel temperature T{sub N} = 5.2K decreases with increasing pressure P and becomes zero at a critical P{sub c} {approx} 3.9 GPa. The A and {rho}{sub 0} values of the low-temperature electrical resistivity {rho} = {rho}{sub 0}+AT{sup 2} in the Fermi liquid relation increase steeply above 3 GPa. A value of A 10.7{omega}cmK{sup -2} at 3.9?GPa is comparable to A = 10{omega}cmK{sup -2} in a heavyfermion superconductor CeCu{sub 2}Si{sub 2}. The heavy fermion state was found to be formed around P{sub c}, in which pressure region superconductivity was found below 0.26K.

Resistive toroidal stability of internal kink modes in circular and shaped tokamaks

International Nuclear Information System (INIS)

Bondeson, A.; Luetjens, H.; Vlad, G.

1991-12-01

The linear resistive magnetohydrodynamical (MHD) stability of the n=1 internal kink mode in tokamaks is studied by toroidal computations. The stabilizing influence of small aspect ratio is confirmed, but it is found that shaping of the cross section influences the internal kink mode significantly. For finite pressure and small resistivity, curvature effects at the q=1 surface make the stability sensitively dependent on shape, and ellipticity (including JET shape) is destabilizing. Only a very restricted set of finite pressure equilibria is completely stable for q 0 <1. A typical result is that the resistive kink mode is slowed down by toroidal effects to a weak tearing/resistive interchange mode. It is suggested that weak resistive instabilities are stabilized during the ramp phase of the sawteeth by effects not included in the linear resistive MHD model. Possible mechanisms for triggering a sawtooth crash are discussed. (author) 18 figs., 34 refs

Structural and Transport Properties of the Weyl Semimetal NbAs at High Pressure

International Nuclear Information System (INIS)

Zhang Jun; Liu Feng-Liang; Dong Jin-Kui; Xu Yang; Li Shi-Yan; Li Na-Na; Yang Wen-Ge

2015-01-01

We perform a series of high-pressure synchrotron x-ray diffraction (XRD) and resistance measurements on the Weyl semimetal NbAs. The crystal structure remains stable up to 26 GPa according to the powder XRD data. The resistance of NbAs single crystal increases monotonically with pressure at low temperature. Up to 20 GPa, no superconducting transition is observed down to 0.3 K. These results show that the Weyl semimetal phase is robust in NbAs, and applying pressure may not be a good way to obtain a topological superconductor from Weyl semimetal NbAs. (paper)

High pressure effect on MoS2 and MoSe2 single crystals grown by ...

Indian Academy of Sciences (India)

Unknown

tetrahedral anvil apparatus up to 5 GPa. In this paper we report room temperature resistance mea- surements as a function of pressure on MoS2 and MoSe2 single crystals. In each case the resistance decreases un- der pressure due to an increase in the carrier concentration. 2. Experimental. Single crystals of MoS2 and ...

Prevalence, predictors, and outcomes in treatment-resistant hypertension in patients with coronary disease.

Science.gov (United States)

Bangalore, Sripal; Fayyad, Rana; Laskey, Rachel; Demicco, David A; Deedwania, Prakash; Kostis, John B; Messerli, Franz H

2014-01-01

Increasingly, apparent treatment-resistant hypertension has been recognized. However, much of the prevalence, predictors, and outcomes are largely unknown, especially in patients with coronary artery disease. We evaluated 10,001 patients with coronary artery disease who were enrolled in the Treating to New Targets trial. Apparent treatment-resistant hypertension was defined as blood pressure ≥ 140 mm Hg despite 3 antihypertensive agents or hypertension. In a multivariable model adjusting for baseline differences, the treatment-resistant hypertension group had a 64% increase in primary outcome (hazard ratio [HR], 1.64; 95% confidence interval [CI], 1.39-1.94; P hypertension group. In addition, patients with apparent treatment-resistant hypertension had a 71% increase in major coronary event (P hypertension group. Results were largely similar whether the definition of apparent treatment-resistant hypertension was based on a blood pressure ≥ 140 mm Hg despite 3 agents or a blood pressure hypertension is associated with a marked increase in the risk of cardiovascular morbidity and mortality, including an increase in all-cause death. Copyright © 2014 Elsevier Inc. All rights reserved.

Modeling of permeate flux and mass transfer resistances in the reclamation of molasses wastewater by a novel gas-sparged nanofiltration

International Nuclear Information System (INIS)

Patel, Tejal Manish; Nath, Kaushik

2014-01-01

A semi-empirical model has been applied to predict the permeate flux and mass transfer resistances during the cross flow nanofiltration of molasses wastewater in flat-sheet module. The model includes laminar flow regime as well as flow in presence of gas sparging at two different gas velocities. Membrane hydraulic resistance (R m ), osmotic pressure resistance (R osm ) and the concentration polarization resistance (R cp ) were considered in series. The concentration polarization resistance was correlated to the operating conditions, namely, the feed concentration, the trans-membrane pressure difference and the cross flow velocity for a selected range of experiments. There was an appreciable reduction of concentration polarization resistance R cp spar in presence of gas sparging. Both the concentration polarization resistance R cp lam and osmotic pressure resistance R osm decreased with cross-flow velocity, but increased with feed concentration and the operating pressure. Experimental and theoretical permeate flux values as a function of cross flow velocity for both the cases, in the presence and absence of gas sparging, were also compared

Modeling of permeate flux and mass transfer resistances in the reclamation of molasses wastewater by a novel gas-sparged nanofiltration

Energy Technology Data Exchange (ETDEWEB)

Patel, Tejal Manish; Nath, Kaushik [G H Patel College of Engineering and Technology, Gujarat (India)

2014-10-15

A semi-empirical model has been applied to predict the permeate flux and mass transfer resistances during the cross flow nanofiltration of molasses wastewater in flat-sheet module. The model includes laminar flow regime as well as flow in presence of gas sparging at two different gas velocities. Membrane hydraulic resistance (R{sub m}), osmotic pressure resistance (R{sub osm}) and the concentration polarization resistance (R{sub cp}) were considered in series. The concentration polarization resistance was correlated to the operating conditions, namely, the feed concentration, the trans-membrane pressure difference and the cross flow velocity for a selected range of experiments. There was an appreciable reduction of concentration polarization resistance R{sub cp}{sup spar} in presence of gas sparging. Both the concentration polarization resistance R{sub cp}{sup lam} and osmotic pressure resistance R{sub osm} decreased with cross-flow velocity, but increased with feed concentration and the operating pressure. Experimental and theoretical permeate flux values as a function of cross flow velocity for both the cases, in the presence and absence of gas sparging, were also compared.

Effects of endurance training on blood pressure, blood pressure-regulating mechanisms, and cardiovascular risk factors.

Science.gov (United States)

Cornelissen, Véronique A; Fagard, Robert H

2005-10-01

Previous meta-analyses of randomized controlled trials on the effects of chronic dynamic aerobic endurance training on blood pressure reported on resting blood pressure only. Our aim was to perform a comprehensive meta-analysis including resting and ambulatory blood pressure, blood pressure-regulating mechanisms, and concomitant cardiovascular risk factors. Inclusion criteria of studies were: random allocation to intervention and control; endurance training as the sole intervention; inclusion of healthy sedentary normotensive or hypertensive adults; intervention duration of > or =4 weeks; availability of systolic or diastolic blood pressure; and publication in a peer-reviewed journal up to December 2003. The meta-analysis involved 72 trials, 105 study groups, and 3936 participants. After weighting for the number of trained participants and using a random-effects model, training induced significant net reductions of resting and daytime ambulatory blood pressure of, respectively, 3.0/2.4 mm Hg (Phypertensive study groups (-6.9/-4.9) than in the others (-1.9/-1.6; Pendurance training decreases blood pressure through a reduction of vascular resistance, in which the sympathetic nervous system and the renin-angiotensin system appear to be involved, and favorably affects concomitant cardiovascular risk factors.

Effects of external pressure on the performance and ageing of single-layer lithium-ion pouch cells

Science.gov (United States)

Mussa, Abdilbari Shifa; Klett, Matilda; Lindbergh, Göran; Lindström, Rakel Wreland

2018-05-01

The effects of external compression on the performance and ageing of NMC(1/3)/Graphite single-layer Li-ion pouch cells are investigated using a spring-loaded fixture. The influence of pressure (0.66, 0.99, 1.32, and 1.98 MPa) on impedance is characterized in fresh cells that are subsequently cycled at the given pressure levels. The aged cells are analyzed for capacity fade and impedance rise at the cell and electrode level. The effect of pressure distribution that may occur in large-format cells or in a battery pack is simulated using parallel connected cells. The results show that the kinetic and mass transport resistance increases with pressure in a fresh cell. An optimum pressure around 1.3 MPa is shown to be beneficial to reduce cyclable-lithium loss during cycling. The minor active mass losses observed in the electrodes are independent of the ageing pressure, whereas ageing pressure affects the charge transfer resistance of both NMC and graphite electrodes and the ohmic resistance of the cell. Pressure distribution induces current distribution but the enhanced current throughput at lower pressures cell does not accelerate its ageing. Conclusions from this work can explain some of the discrepancies in non-uniform ageing reported in the literature and indicate coupling between electrochemistry and mechanics.

Identification of canine coronary resistance and intramyocardial compliance on the basis of the waterfall model.

Science.gov (United States)

Burattini, R; Sipkema, P; van Huis, G A; Westerhof, N

1985-01-01

This study was performed to elucidate the effects of cardiac contraction on coronary pressure-flow relations. On the basis of the waterfall mechanism, a lumped model of the coronary arterial system is presented consisting of a proximal (epicardial) compliance, a coronary resistance, and an intramyocardial compliance. A "back"-pressure, assumed to be proportional (constant k) to left ventricular pressure, impedes flow. From steady-state measurements of circumflex coronary artery flow and inflow pressure, together with left ventricular pressure, the values of the three model parameters and the constant k have been estimated. In the control condition proximal compliance is found to be 1.7 X 10(-12) m4s2kg-1, intramyocardial compliance 110 X 10(-12)m4s2kg-1, and resistance 7.5 X 10(9) kgm-4s-1. The proportionality constant k is close to unity. Effects of changes in left ventricular pressure and inflow pressure and the effect of vasoactive drugs on the parameters are also investigated. Changes in coronary resistance are always opposite to changes in intramyocardial compliance. Sensitivity analysis showed that epicardial compliance plays its major role during isovolumic contraction and relaxation; resistance plays a role throughout the cardiac cycle but is more important in diastole than in systole, whereas intramyocardial compliance plays a role in systole and in early diastole.

Effects of pressure on doped Kondo insulators

International Nuclear Information System (INIS)

Lee, Chengchung; Xu, Wang

1999-08-01

The effects of pressure on the doped Kondo insulators (KI) are studied in the framework of the slave-boson mean-field theory under the coherent potential approximation (CPA). A unified picture for both electron-type KI and hole-type KI is presented. The density of states of the f-electrons under the applied pressures and its variation with the concentration of the Kondo holes are calculated self-consistently. The specific heat coefficient, the zero-temperature magnetic susceptibility as well as the low temperature electric resistivity of the doped KI under various pressures are obtained. The two contrasting pressure-dependent effects observed in the doped KI systems can be naturally explained within a microscopic model. (author)

Control of electrical resistivity of TaN thin films by reactive sputtering for embedded passive resistors

International Nuclear Information System (INIS)

Kang, S.M.; Yoon, S.G.; Suh, S.J.; Yoon, D.H.

2008-01-01

Tantalum nitride thin films were deposited by radio frequency (RF) reactive sputtering at various N 2 /Ar gas flow ratios and working pressures to examine the change of their electrical resistivity. From the X-ray diffraction (XRD) and four-point probe sheet resistance measurements of the TaN x films, it was found that the change of the crystalline structures of the TaN x films as a function of the N 2 partial pressure caused an abrupt change of the electrical resistivity. When the hexagonal structure TaN thin films changed to an f.c.c. structure, the sheet resistance increased from 16 Ω/sq to 1396 Ω/sq. However, we were able to control the electrical resistivity of the TaN thin film in the range from 69 Ω/sq to 875 Ω/sq, with no change in crystalline structure, within a certain range of working pressures. The size of the grains in the scanning electron microscopy (SEM) images seemed to decrease with the increase of working pressure

Acute resistance exercise using free weights on aortic wave reflection characteristics.

Science.gov (United States)

Tai, Yu Lun; Gerhart, Hayden; Mayo, Xián; Kingsley, J Derek

2018-01-01

Aortic wave reflection characteristics such as the augmentation index (AIx), wasted left ventricular pressure energy (ΔE w ) and aortic haemodynamics, such as aortic systolic blood pressure (ASBP), strongly predict cardiovascular events. The effects of acute resistance exercise (ARE) using free-weight exercises on these characteristics are unknown. Therefore, we sought to determine the effects of acute free-weight resistance exercise on aortic wave reflection characteristics and aortic haemodynamics in resistance-trained individuals. Fifteen young, healthy resistance-trained (9 ± 3 years) individuals performed two randomized sessions consisting of an acute bout of free-weight resistance exercise (ARE) or a quiet control (CON). The ARE consisted of three sets of 10 repetitions at 75% one repetition maximum for squat, bench press and deadlift. In CON, the participants rested in the supine position for 30 min. Measurements were made at baseline before sessions and 10 min after sessions. A two-way ANOVA was used to compare the effects of condition across time. There were no significant interactions for aortic or brachial blood pressures. Compared to rest, there were significant increases in augmentation pressure (rest: 5·7 ± 3·0 mmHg; recovery: 10·4 ± 5·7 mmHg, P = 0·002), AIx (rest: 116·8 ± 4·2%; recovery: 123·2 ± 8·4%, P = 0·002), AIx normalized at 75 bpm (rest: 5·2 ± 7·6%; recovery: 27·3 ± 13·2%, Pfree-weight exercises may have no effect on aortic and brachial blood pressure but may significantly alter aortic wave reflection characteristics. © 2016 Scandinavian Society of Clinical Physiology and Nuclear Medicine. Published by John Wiley & Sons Ltd.

Real-time display of flow-pressure-volume loops.

Science.gov (United States)

Morozoff, P E; Evans, R W

1992-01-01

Graphic display of respiratory waveforms can be valuable for monitoring the progress of ventilated patients. A system has been developed that can display flow-pressure-volume loops as derived from a patient's respiratory circuit in real time. It can also display, store, print, and retrieve ventilatory waveforms. Five loops can be displayed at once: current, previous, reference, "ideal," and previously saved. Two components, the data-display device (DDD) and the data-collection device (DCD), comprise the system. An IBM 286/386 computer with a graphics card (VGA) and bidirectional parallel port is used for the DDD; an eight-bit microprocessor card and an A/D convertor card make up the DCD. A real-time multitasking operating system was written to control the DDD, while the DCD operates from in-line assembly code. The DCD samples the pressure and flow sensors at 100 Hz and looks for a complete flow waveform pattern based on flow slope. These waveforms are then passed to the DDD via the mutual parallel port. Within the DDD a process integrates the flow to create a volume signal and performs a multilinear regression on the pressure, flow, and volume data to calculate the elastance, resistance, pressure offset, and coefficient of determination. Elastance, resistance, and offset are used to calculate Pr and Pc where: Pr[k] = P[k]-offset-(elastance.V[k]) and Pc[k] = P[k]-offset-(resistance.F[k]). Volume vs. Pc and flow vs. Pr can be displayed in real time. Patient data from previous clinical tests were loaded into the device to verify the software calculations. An analog waveform generator was used to simulate flow and pressure waveforms that validated the system.(ABSTRACT TRUNCATED AT 250 WORDS)

Antimicrobial usage and resistance in beef production

OpenAIRE

Cameron, Andrew; McAllister, Tim A.

2016-01-01

Antimicrobials are critical to contemporary high-intensity beef production. Many different antimicrobials are approved for beef cattle, and are used judiciously for animal welfare, and controversially, to promote growth and feed efficiency. Antimicrobial administration provides a powerful selective pressure that acts on the microbial community, selecting for resistance gene determinants and antimicrobial-resistant bacteria resident in the bovine flora. The bovine microbiota includes many harm...

The effect of flaxseed powder on insulin resistance indices and blood pressure in prediabetic individuals: A randomized controlled clinical trial

Directory of Open Access Journals (Sweden)

Afrooz Javidi

2016-01-01

Full Text Available Background: Designing the effective and early interventions can prevent progression of prediabetes to diabetes. Few studies have shown the effect of flaxseed on glycemic control. This study aimed to assess the effect of flaxseed powder on insulin resistance (IR indices and blood pressure in prediabetic individuals. Materials and Methods: In a randomized clinical trial, 99 prediabetic individuals were randomly divided into three groups: two groups received 40 g (FG40 and 20 g (FG20 flaxseed powder daily for 12 weeks and the third group was the control (CG. Before and after the intervention, anthropometric measurements, blood pressure, fasting serum glucose (FSG, insulin, homeostasis model assessment IR index (HOMA-IR, beta-cell function, and insulin sensitivity were measured. Results: FSG significantly declined overall in all groups compared to the baseline (P = 0.002 in CG and FG20 groups and P = 0.001 in FG40. In contrast, mean of the changes in FSG was not significantly different between groups. Insulin concentration did not change significantly within and between the investigated groups. Although HOMA-IR reduced in FG20 (P = 0.033, the mean of changes was not significant between the three groups. Mean of beta-cell function increased in CG and FG40 groups compared to the baseline (P = 0.044 and P = 0.018, respectively, but mean of its changes did not show any difference between the three groups. The mean of changes in IR indices was not significant between the three groups. FG40 group had significantly lowered systolic blood pressure after the intervention (P = 0.005. Conclusion: Daily intake of flaxseed powder lowered blood pressure in prediabetes but did not improve glycemic and IR indices.

Performance test of ex-core high temperature and high pressure water loop test equipment (Contract research)

International Nuclear Information System (INIS)

Nakano, Hiroko; Uehara, Toshiaki; Takeuchi, Tomoaki; Shibata, Hiroshi; Nakamura, Jinichi; Matsui, Yoshinori; Tsuchiya, Kunihiko

2016-03-01

In Japan Atomic Energy Agency, we started research and development so as to monitor the situations in the Nuclear Plant Facilities during a severe accident, such as a radiation-resistant monitoring camera, a radiation-resistant transmission system for conveying the in-core information, and a heat-resistant signal cable. As a part of developments of the heat-resistant signal cable, we prepared ex-core high-temperature and high-pressure water loop test equipment, which can simulate the conditions of BWRs and PWRs, for evaluating reliability and properties of sheath materials of the cable. This equipment consists of autoclave, water conditioning tank, high-pressure metering pump, preheater, heat exchanger and water purification equipment, etc. This report describes the basic design and the performance test results of ex-core high-temperature and high-pressure water loop test equipment. (author)

[Pressure sores in a university hospital].

Science.gov (United States)

Barbut, Frédéric; Parzybut, Bérengère; Boëlle, Pierre-Yves; Neyme, Denis; Farid, Rachida; Kosmann, Marie-Jeanne; Luquel, Laurence

2006-05-01

To determine the prevalence of pressure sores, their risk factors, and the responsible microbial agents in an acute-care hospital and to evaluate their management. A prevalence survey was conducted from 5 July through 9 July 2004. Investigators completed a standardized questionnaire for each hospitalized patient, including demographic data (age, sex, previous hospitalizations, etc.) and Braden scale risk factors (sensory perception, humidity, activity, mobility, nutrition, and friction and shear). Two experts in skin care detected pressure sores by physical examination of the patients. Each pressure sore was swabbed and inoculated on selective media. Management was evaluated by reviewing the clinical charts of each patient with a pressure sore. The study included 535 adult patients (aged 59 +/- 19 years): 75 ulcer sores were observed in 37 patients (prevalence=6.9%). Stage I sores accounted for 24% of the total, stage II for 29%, stage III 31%, and stage IV 16%. The most frequent site was the heel (41%), followed by the sacrum (20%), elbow (11%), back (7%) and ischial tuberosities (7%). Sixty (80%) were acquired while hospitalized. Age-adjusted multivariate analyses found that the risk factors significantly associated with pressure sores were Braden scorepressure sores (OR=5.0 95% CI: 2.2-11.6, psores (24.5%), mostly stage III and IV, were colonized by multiple-drug-resistant bacteria (i.e., methicillin resistant Staphylococcus aureus, extended spectrum beta-lactamase Enterobacteriaceae). Seven (9.3%) of the 75 ulcers were diagnosed only during the survey, by the experts; of the 68 diagnosed before the survey, 57 (83.8%) had been under treatment. Treatment was considered inappropriate according to French guidelines in 31.6% of the cases. This prospective prevalence study resulted in better awareness of the patients at risk for pressure sores. It also made the recently created mobile geriatrics unit better known within the hospital.

Soft-Matter Resistive Sensor for Measuring Shear and Pressure Stresses

Science.gov (United States)

Tepayotl-Ramirez, Daniel; Roberts, Peter; Majidi, Carmel

2013-03-01

Building on emerging paradigms in soft-matter electronics, we introduce liquid-phase electronic sensors that simultaneously measures elastic pressure and shear deformation. The sensors are com- posed of a sheet of elastomer that is embedded with fluidic channels containing eutectic Gallium- Indium (EGaIn), a metal alloy that is liquid at room temperature. Applying pressure or shear traction to the surface of the surrounding elastomer causes the elastomer to elastically deform and changes the geometry and electrical properties of the embedded liquid-phase circuit elements. We introduce analytic models that predict the electrical response of the sensor to prescribed surface tractions. These models are validated with both Finite Element Analysis (FEA) and experimental measurements.

Predicting the wheel rolling resistance regarding important motion parameters using the artificial neural network

Directory of Open Access Journals (Sweden)

F Gheshlaghi

2016-04-01

Full Text Available Introduction: Rolling resistance is one of the most substantial energy losses when the wheel moves on soft soil. Rolling resistance value optimization will help to improve energy efficiency. Accurate modeling of the interaction soil-tire is an important key to this optimization and has eliminated the need for costly field tests and has reduced the time required to test. Rolling resistance will change because of the tire and wheel motion parameters and characteristics of the ground surface. Some tire design parameters are more important such as the tire diameter, width, tire aspect ratio, lugs form, inflation pressure and mechanical properties of tire structure. On the other hand, the soil or ground surface characteristics include soil type; moisture content and bulk density have an important role in this phenomenon. In addition, the vertical load and the wheel motion parameters such as velocity and tire slip are the other factors which impact on tire rolling resistance. According to same studies about the rolling resistance of the wheel, the wheel is significantly affected by the dynamic load. Tire inflation pressure impacted on rolling resistance of tires that were moving on hard surfaces. Studies showed that the rolling resistance of tires with low inflation pressure (less than 100 kPa was too high. According to Zoz and Griss researches, increasing the tire pressure increases rolling resistance on soft soil but reduces the rolling resistance of on-road tires and tire-hard surface interaction. Based on these reports, the effect of velocity on tire rolling resistance for tractors and vehicles with low velocity (less than 5 meters per second is usually insignificant. According to Self and Summers studies, rolling resistance of the wheel is dramatically affected by dynamic load on the wheel. Artificial Neural Network is one of the best computational methods capable of complex regression estimation which is an advantage of this method compared with

Emotions and stress increase respiratory resistance in asthma.

Science.gov (United States)

Ritz, T; Steptoe, A; DeWilde, S; Costa, M

2000-01-01

Clinical reports suggest that various emotions and types of stress can precipitate asthmatic symptoms, but there is little experimental evidence to substantiate this claim. We studied the impact of different emotional states and stress on respiratory resistance in asthmatic and nonasthmatic individuals. Participants (24 asthmatic and 24 nonasthmatic patients) viewed short film sequences selected to induce anxiety, anger, depression, elation, happiness, contentment, or a neutral affective state and completed two stressful tasks, mental arithmetic to induce active coping efforts and viewing of medical slides to induce passive coping efforts. Oscillatory resistance, heart rate, blood pressure, baroreflex sensitivity, skin conductance level, respiration rate and volume, and self-reported affective state were measured throughout the session. Uniform increases in oscillatory resistance were found in all emotional states compared with the neutral state and during mental arithmetic in both groups. Asthmatic patients showed stronger reactions to the medical slides than healthy control subjects, with significant increases in oscillatory resistance, blood pressure, skin conductance level, and minute volume, as well as higher levels of self-reported depression, arousal, and shortness of breath. Changes in oscillatory resistance were inconsistently correlated with other physiological indices. Various emotional states and stress increase oscillatory resistance largely independently of concurrent increases in autonomic or ventilatory activity. The particular sensitivity of asthmatics to passive coping demand requires additional research.

Influence of isoflurane on the diastolic pressure-flow relationship and critical occlusion pressure during arterial CABG surgery: a randomized controlled trial.

Science.gov (United States)

Hinz, José; Mansur, Ashham; Hanekop, Gerd G; Weyland, Andreas; Popov, Aron F; Schmitto, Jan D; Grüne, Frank F G; Bauer, Martin; Kazmaier, Stephan

2016-01-01

The effects of isoflurane on the determinants of blood flow during Coronary Artery Bypass Graft (CABG) surgery are not completely understood. This study characterized the influence of isoflurane on the diastolic Pressure-Flow (P-F) relationship and Critical Occlusion Pressure (COP) during CABG surgery. Twenty patients undergoing CABG surgery were studied. Patients were assigned to an isoflurane or control group. Hemodynamic and flow measurements during CABG surgery were performed twice (15 minutes after the discontinuation of extracorporeal circulation (T15) and again 15 minutes later (T30)). The zero flow pressure intercept (a measure of COP) was extrapolated from a linear regression analysis of the instantaneous diastolic P-F relationship. In the isoflurane group, the application of isoflurane significantly increased the slope of the diastolic P-F relationship by 215% indicating a mean reduction of Coronary Vascular Resistance (CVR) by 46%. Simultaneously, the Mean Diastolic Aortic Pressure (MDAP) decreased by 19% mainly due to a decrease in the systemic vascular resistance index by 21%. The COP, cardiac index, heart rate, Left Ventricular End-Diastolic Pressure (LVEDP) and Coronary Sinus Pressure (CSP) did not change significantly. In the control group, the parameters remained unchanged. In both groups, COP significantly exceeded the CSP and LVEDP at both time points. We conclude that short-term application of isoflurane at a sedative concentration markedly increases the slope of the instantaneous diastolic P-F relationship during CABG surgery implying a distinct decrease with CVR in patients undergoing CABG surgery.

Intensidades de treinamento resistido e pressão arterial de idosas hipertensas - um estudo piloto Resistance training intensities and blood pressure of hypertensive older women - a pilot study

Directory of Open Access Journals (Sweden)

Eline Silva da Cunha

2012-12-01

Full Text Available INTRODUÇÃO: Observa-se que a literatura apresenta uma lacuna acerca da intensidade ideal de treinamento resistido para idosos hipertensos, os poucos estudos existentes utilizam treinamentos com diferentes intensidades. OBJETIVO: Verificar o efeito de duas intensidades de treinamento resistido sobre a pressão arterial de idosas hipertensas controladas. Métodos: Dezesseis idosas hipertensas, controladas por medicação anti-hipertensiva, foram divididas em dois grupos através de sorteio. Nove pacientes foram submetidas a treinamento resistido moderado (G1 e sete, a treinamento resistido leve (G2. As pacientes realizaram oito semanas de treinamento resistido, com frequência de três vezes por semana em dias alternados, no período vespertino. Os exercícios realizados foram respectivamente: leg press, supino reto, extensão de joelhos, puxada frontal, flexão de joelhos, abdução de ombro, abdução unilateral de quadril com cross over e rosca direta com barra. RESULTADOS: As pacientes do G1 apresentaram redução tanto nos valores de repouso da pressão arterial diastólica (PAD p BACKGROUND: The optimum intensity of resistance training for hypertensive elderly has not been studied yet and the few studies in the literature used training with distinct intensities. Objective: To verify the effect of two resistance training intensities on blood pressure (BP of elderly women with controlled hypertension. METHODS: Sixteen older women with hypertension controlled by anti-hypertensive drug were randomly divided into two groups. Nine patients were submitted to moderate resistance training (G1 and seven patients were submitted to mild resistance training (G2. The patients underwent eight weeks of resistance training, with frequency of three times per week on alternate days in the afternoon. The exercises performed were: leg press, bench press, knee extension, lat pull-down, knee flexion, shoulder abduction, standing cable hip abduction and biceps

Hydrodynamic resistance and flow patterns in the gills of a tilapine fish.

Science.gov (United States)

Strother, James A

2013-07-15

The gills of teleost fishes are often discussed as an archetypal counter-current exchange system, capable of supporting the relatively high metabolic rates of some fishes despite the low oxygen solubility of water. Despite an appreciation for the physiology of exchange at the gills, many questions remain regarding the hydrodynamical basis of ventilation in teleost fishes. In this study, the hydrodynamic resistance and flow fields around the isolated gills of a tilapia, Oreochromis mossambicus, were measured as a function of the applied pressure head. At ventilatory pressures typical of a fish at rest, the hydrodynamic resistance of the gills was nearly constant, the flow was laminar, shunting of water around the gills was essentially absent, and the distribution of water flow was relatively uniform. However, at the higher pressures typical of an active or stressed fish, some of these qualities were lost. In particular, at elevated pressures there was a decrease in the hydrodynamic resistance of the gills and substantial shunting of water around the gills. These effects suggest mechanical limits to maximum aerobic performance during activity or under adverse environmental conditions.

Insulin resistance and associated dysfunction of resistance vessels and arterial hypertension

DEFF Research Database (Denmark)

Henriksen, Jens Henrik; Møller, Søren

2005-01-01

, calcitonin gene-related peptide, nitric oxide, and other vasodilators, and is most pronounced in the splanchnic area. This provides an effective (although relative) counterbalance to raised arterial blood pressure. Subjects with arterial hypertension (essential, secondary) may become normotensive during......This review looks at the alterations in the systemic haemodynamics of patients with chronic liver disease (cirrhosis) in relation to essential hypertension and arterial hypertension of renal origin. Characteristic findings in patients with cirrhosis are vasodilatation with low overall systemic...... vascular resistance, high arterial compliance, increased cardiac output, secondary activation of counterregulatory systems (renin-angiotensin-aldosterone system, sympathetic nervous system, release of vasopressin), and resistance to vasopressors. The vasodilatory state is mediated through adrenomedullin...

Antibiotic-resistant bacteria: a challenge for the food industry.

Science.gov (United States)

Capita, Rosa; Alonso-Calleja, Carlos

2013-01-01

Antibiotic-resistant bacteria were first described in the 1940s, but whereas new antibiotics were being discovered at a steady rate, the consequences of this phenomenon were slow to be appreciated. At present, the paucity of new antimicrobials coming into the market has led to the problem of antibiotic resistance fast escalating into a global health crisis. Although the selective pressure exerted by the use of antibiotics (particularly overuse or misuse) has been deemed the major factor in the emergence of bacterial resistance to these antimicrobials, concerns about the role of the food industry have been growing in recent years and have been raised at both national and international levels. The selective pressure exerted by the use of antibiotics (primary production) and biocides (e.g., disinfectants, food and feed preservatives, or decontaminants) is the main driving force behind the selection and spread of antimicrobial resistance throughout the food chain. Genetically modified (GM) crops with antibiotic resistance marker genes, microorganisms added intentionally to the food chain (probiotic or technological) with potentially transferable antimicrobial resistance genes, and food processing technologies used at sub-lethal doses (e.g., alternative non-thermal treatments) are also issues for concern. This paper presents the main trends in antibiotic resistance and antibiotic development in recent decades, as well as their economic and health consequences, current knowledge concerning the generation, dissemination, and mechanisms of antibacterial resistance, progress to date on the possible routes for emergence of resistance throughout the food chain and the role of foods as a vehicle for antibiotic-resistant bacteria. The main approaches to prevention and control of the development, selection, and spread of antibacterial resistance in the food industry are also addressed.

High-pressure needle interface for thermoplastic microfluidics.

Science.gov (United States)

Chen, C F; Liu, J; Hromada, L P; Tsao, C W; Chang, C C; DeVoe, D L

2009-01-07

A robust and low dead volume world-to-chip interface for thermoplastic microfluidics has been developed. The high pressure fluidic port employs a stainless steel needle inserted into a mating hole aligned to an embedded microchannel, with an interference fit used to increase pressure resistance. Alternately, a self-tapping threaded needle screwed into a mating hole is also demonstrated. In both cases, the flat bottom needle ports seat directly against the microchannel substrate, ensuring low interfacial dead volumes. Low dispersion is observed for dye bands passing the interfaces. The needle ports offer sufficient pull-out forces for applications such as liquid chromatography that require high internal fluid pressures, with the epoxy-free interfaces compatible with internal microchannel pressures above 40 MPa.

Diagnosis and management of resistant hypertension: state of the art.

Science.gov (United States)

Wei, Fang-Fei; Zhang, Zhen-Yu; Huang, Qi-Fang; Staessen, Jan A

2018-04-26

Resistant hypertension is defined as a lack of ambulatory blood pressure response to optimized medical treatment after exclusion of secondary hypertension in patients who are fully adherent to antihypertensive therapy. Patients with resistant hypertension are at high risk of complications, particularly cardiovascular events, and optimization of medical treatment remains the cornerstone of their management. Such optimization should be based on simple algorithms and include the use of aldosterone antagonists. The available data from clinical trials do not support the use of device-based approaches such as renal denervation, baroreflex activation therapy or arteriovenous anastomosis for the treatment of resistant hypertension in the majority of patients. Therefore, device treatment remains a last-resort for patients with truly resistant hypertension in the context of clinical research in highly skilled tertiary referral centres. Future research should focus on improving understanding of the intrinsic (physiological and psychological factors) and extrinsic (environmental stressors) mechanisms that contribute to a lack of response to blood-pressure-lowering drugs in adherent patients. The use of biomarkers to identify patients with early target organ damage and new technologies, such as renal nerve stimulation, to predict blood pressure responses to renal denervation could aid the selection of patients who might benefit from device therapies.

The effects of angiotensin II receptor antagonist (candesartan on rat renal vascular resistance

Directory of Open Access Journals (Sweden)

Supatraviwat, J

2004-05-01

Full Text Available The present study aimed to investigate the action of angiotensin II (AII on renal perfusion pressure and renal vascular resistance using noncompetitive AT1-receptor antagonist (candesartan or CV 11974. Experiments were performed in isolated kidney of adult male Wistar rats. Kreb's Henseleit solution was perfused into the renal artery at the rate of 3.5 ml/min. This flow rate was designed in order to maintain renal perfusion pressure between 80-120 mm Hg. Dose-response relationship between perfusion flow rate and AII concentration were studied. Renal perfusion pressure in response to 1, 10 and 100 nM AII were increased from basal perfusion pressure of 94±8 mm Hg to 127±6, 157±12 and 190±16 mm Hg, respectively. Administration of perfusate containing 11.4 μM candesartan for 30 min had no effect on the basal perfusion pressure. However, this significantly reduced renal perfusion pressure in the presence of AII (1, 10 and 100 nM by 39%, 47% and 61%, (n=7, P<0.05 respectively. At the basal perfusion pressure, calculated renal vascular resistance was 27±2 mm Hg · min · ml-1. However, the vascular resistance were found to be 41±1, 45±2 and 47±2 mm Hg · min · ml-1 when 1, 10 and 100 nM AII were added. Moreover, this dose of candesartan also showed a significant decrease in renal vascular resistance at the corresponding doses of AII by 38%, 48% and 43%, (n=7, P<0.05 respectively. The higher dose of candesartan (22.7 μM completely inhibited the action of 1, 10 and 100 nM AII on renal vasoconstriction. These results may indicate that the action of AII on renal vascular resistance is via AT1-receptor, at least in rat isolated perfusion kidney.

Flux limitation in ultrafiltration: Osmotic pressure model and gel layer model

NARCIS (Netherlands)

Wijmans, J.G.; Nakao, S.; Smolders, C.A.

1984-01-01

The characteristic permeate flux behaviour in ultrafiltration, i.e., the existence of a limiting flux which is independent of applied pressure and membrane resistance and a linear plot of the limiting flux versus the logarithm of the feed concentration, is explained by the osmotic pressure model. In

Pressure balanced type membrane covered polarographic oxygen detectors for use in high temperature-high pressure water, (1)

International Nuclear Information System (INIS)

Nakayama, Norio; Uchida, Shunsuke

1984-01-01

A pressure balanced type membrane covered polarographic oxygen detector was developed to determine directly oxygen concentrations in high temperature, high pressure water without cooling and pressure reducing procedures. The detector is characterized by the following features: (1) The detector body and the membrane for oxygen penetration are made of heat resistant resin. (2) The whole detector body is contained in a pressure chamber where interior and exterior pressures of the detector are balanced. (3) Thermal expansion of the electrolyte is absorbed by deformation of a diaphragm attached to the detector bottom. (4) The effect of dissolved Ag + on the signal current is eliminated by applying a guard electrode. As a result of performance tests at elevated temperature, it was demonstrated that a linear relationship between oxygen concentration and signal current was obtained up to 285 0 C, which was stabilized by the guard electrode. The minimum O 2 concentration detectable was 0.03ppm (9.4 x 10 -7 mol/kg). (author)

Better Renal Resistive Index Profile in Subjects with Beta Thalassemia Minor .

Science.gov (United States)

Basut, Fahrettin; Keşkek, Şakir Özgür; Gülek, Bozkurt

2018-05-03

Beta thalassaemia minor is a common genetic disorder without any characteristic symptoms except mild anemia. It is found to be associated with some cardiovascular risk factors such as insulin resistance and diabetes mellitus. The renal resistive index (RRI) is a measure of renal arterial resistance to blood flow. The aim of this study was to evaluate the renal resistive index in subjects with beta thalassaemia minor (BTM). A total of 253 subjects were included in this cross-sectional study. The study group consisted of 148 subjects with BTM and the control group consisted of 105 healthy subjects. Beta thalassaemia minor was diagnosed by complete blood count and hemoglobin electrophoresis. Blood pressure measurement and biochemical tests were performed. Renal resistive index of all subjects was measured using renal Doppler ultrasonography. Subjects with beta thalassemia minor had lower renal resistive indices compared to healthy subjects (0.58 ± 0.04 vs. 0.60 ± 0.06, p = 0.0016). Additionally, the RRI levels of subjects with BTM were correlated with systolic blood pressure (p = 0.017, r = 0.194). In this study, lower renal resistive index was found in subjects with BTM. This may be associated with decreased vascular resistance and blood viscosity in these subjects. ©2018The Author(s). Published by S. Karger AG, Basel.

Induction of Shiga toxin-converting prophage in Escherichia coli by high hydrostatic pressure.

Science.gov (United States)

Aertsen, Abram; Faster, David; Michiels, Chris W

2005-03-01

Since high hydrostatic pressure is becoming increasingly important in modern food preservation, its potential effects on microorganisms need to be thoroughly investigated. In this context, mild pressures (pressures. In this report, we extend this observation to lambdoid Shiga toxin (Stx)-converting bacteriophages in MG1655, which constitute an important virulence trait in Stx-producing E. coli strains (STEC). The window of pressures capable of inducing Stx phages correlated well with the window of bacterial survival. When pressure treatments were conducted in whole milk, which is known to promote bacterial survival, Stx phage induction could be observed at up to 250 MPa in E. coli MG1655 and at up to 300 MPa in a pressure-resistant mutant of this strain. In addition, we found that the intrinsic pressure resistance of two types of Stx phages was very different, with one type surviving relatively well treatments of up to 400 MPa for 15 min at 20 degrees C. Interestingly, and in contrast to UV irradiation or mitomycin C treatment, pressure was not able to induce Stx prophage or an SOS response in several natural Stx-producing STEC isolates.

Liquefaction resistance of calcareous sands

International Nuclear Information System (INIS)

Sandoval Vallejo, Eimar

2012-01-01

Calcareous sands are unique in terms of their origin, mineralogy, shape, fragility and intra particle porosity. This article presents results from an experimental program carried out to study the liquefaction resistance of a calcareous sand retrieved from Cabo Rojo at Puerto Rico. The experimental program included mineralogical characterization, index properties, and undrained cyclic triaxial tests on isotropically consolidated reconstituted samples. Due to the large variation in the calcareous sand properties, results are compared with previous researches carried out on other calcareous sands around the world. Results showed a wide range in the liquefaction resistance of the studied calcareous sands. Cabo Rojo sand experienced greater liquefaction resistance than most of the calcareous sands used for comparison. Important differences in the excess pore pressure generation characteristics were also found.

On-line monitoring of resistance of aqueous solutions at high temperature

International Nuclear Information System (INIS)

Hu Shilin; Zhang Pingzhu; Shang Weiguo

1999-01-01

The coulostatic measurement is a fast speed electrochemical test method. By this technology, analyzing Δ E(t)- T curves recorded under coulostatic perturbation, the solution resistance R l , resistance of coated film R f , capacity of coated film C f , Polarization resistance R p and double layer capacity C d are obtained. The resistance variety of 0.05N KCl is measured from room temperature up to 255 deg. C under saturation steam pressure. (author)

Design optimization of a thin walled pressure vessel

International Nuclear Information System (INIS)

Sadiq, S.

2001-01-01

Design evaluation of a pressure vessel is not only to build confidence on its integrity but also to reduce structural weight and enhance the performance of the structure. Pressure vessel, e.g., a rocket motor not only has to withstand the high operating temperatures but it must also be able to survive the internal pressures and external aerodynamic forces and bending stresses during its operation in flight. A research program was devised to study the stresses, which are generated in a thin walled pressure vessel during actual operation and its simulation with cold testing technique, i.e., by means of hydrostatic testing employing electrical resistance strain gauges on the external surface of the cylinder. The objective of the research was to uphold the performance of the vessel by reducing its thickness from 6.09 to 5.5 mm (which of course reduces the safety factor margin from 1.8 to 1.5); thereby curtailing the overall structural weight and maintaining the efficiency of the vessel itself during its live operation. The techniques employed were hydrostatic testing, data acquisition system for obtaining data on strains from the electrical resistance strain gauges and later employing V on Mises yield criterion empirical relation to computer the stresses in hoop and longitudinal directions. (author)

Renal denervation in treatment-resistant essential hypertension. A randomized, SHAM-controlled, double-blinded 24-h blood pressure-based trial.

Science.gov (United States)

Mathiassen, Ole N; Vase, Henrik; Bech, Jesper N; Christensen, Kent L; Buus, Niels H; Schroeder, Anne P; Lederballe, Ole; Rickers, Hans; Kampmann, Ulla; Poulsen, Per L; Hansen, Klavs W; Btker, Hans E; Peters, Christian D; Engholm, Morten; Bertelsen, Jannik B; Lassen, Jens F; Langfeldt, Sten; Andersen, Gratien; Pedersen, Erling B; Kaltoft, Anne

2016-08-01

Renal denervation (RDN), treating resistant hypertension, has, in open trial design, been shown to lower blood pressure (BP) dramatically, but this was primarily with respect to office BP. We conducted a SHAM-controlled, double-blind, randomized, single-center trial to establish efficacy data based on 24-h ambulatory BP measurements (ABPM). Inclusion criteria were daytime systolic ABPM at least 145 mmHg following 1 month of stable medication and 2 weeks of compliance registration. All RDN procedures were carried out by an experienced operator using the unipolar Medtronic Flex catheter (Medtronic, Santa Rosa, California, USA). We randomized 69 patients with treatment-resistant hypertension to RDN (n = 36) or SHAM (n = 33). Groups were well balanced at baseline. Mean baseline daytime systolic ABPM was 159 ± 12 mmHg (RDN) and 159 ± 14 mmHg (SHAM). Groups had similar reductions in daytime systolic ABPM compared with baseline at 3 months [-6.2 ± 18.8 mmHg (RDN) vs. -6.0 ± 13.5 mmHg (SHAM)] and at 6 months [-6.1 ± 18.9 mmHg (RDN) vs. -4.3 ± 15.1 mmHg (SHAM)]. Mean usage of antihypertensive medication (daily defined doses) at 3 months was equal [6.8 ± 2.7 (RDN) vs. 7.0 ± 2.5 (SHAM)].RDN performed at a single center and by a high-volume operator reduced ABPM to the same level as SHAM treatment and thus confirms the result of the HTN3 trial. Further, clinical use of RDN for treatment of resistant hypertension should await positive results from double-blinded, SHAM-controlled trials with multipolar ablation catheters or novel denervation techniques.

Pressure effect on iron based superconductors

International Nuclear Information System (INIS)

Arumugam, S.; Kanagaraj, M.

2011-01-01

A tuning of macroscopic thermo dynamical parameters such as temperature, pressure and volume play a crucial role in strongly correlated electron systems especially high T c superconductors, which leads to increasing conductivity as well as effective way of reducing intrinsic magnetic moments. Application of chemical and external pressure exhibits significant increases of critical temperature of recently discovered iron pnictides and chalcogenides superconductors. In this present report, we have investigated hydrostatic pressure effects on resistivity and magnetization of some 1111 type based oxypnictide superconductors such as Co doped CeFeAsO, La 0.8 Th 0.2 FeAsO, Ce 0.6 Y 0.4 FeAsO 0.8 F 0.2 and Yb doped CeFeAsO systems respectively. The initially applied pressure increases the T c and its down to lower value when beyond increasing pressure also has been observed and pressure effects on crystal structure were also discussed. From that all the obtained results reveal that controlling of magnetic instability and structure distortion at higher pressure is a dominant way to further developing of T c of these new ferropnictides compounds. (author)

Infection control implications of heterogeneous resistance mechanisms in carbapenem-resistant Enterobacteriaceae (CRE).

Science.gov (United States)

Goodman, K E; Simner, P J; Tamma, P D; Milstone, A M

2016-01-01

The Centers for Disease Control and Prevention (CDC) defines carbapenem-resistant Enterobacteriaceae (CRE) based upon a phenotypic demonstration of carbapenem resistance. However, considerable heterogeneity exists within this definitional umbrella. CRE may mechanistically differ by whether they do or do not produce carbapenemases. Moreover, patients can acquire CRE through multiple pathways: endogenously through antibiotic selective pressure on intestinal microbiota, exogenously through horizontal transmission or through a combination of these factors. Some evidence suggests that non-carbapenemase-producing CRE may be more frequently acquired by antibiotic exposure and carbapenemase-producing CRE via horizontal transmission, but definitive data are lacking. This review examines types of CRE resistance mechanisms, antibiotic exposure and horizontal transmission pathways of CRE acquisition, and the implications of these heterogeneities to the development of evidence-based CRE healthcare epidemiology policies. In our Expert Commentary & Five-Year View, we outline specific nosocomial CRE knowledge gaps and potential methodological approaches for their resolution.

Tokamak m = 1 magnetohydrodynamic calculations in toroidal geometry using a full set of nonlinear resistive magnetohydrodynamic equations

International Nuclear Information System (INIS)

Charlton, L.A.; Carreras, B.A.; Holmes, J.A.; Lynch, V.E.

1988-01-01

The linear stability and nonlinear evolution of the resistive m = 1 mode in tokamaks is studied using a full set of resistive magnetohydrodynamic (MHD) equations in toroidal geometry. The modification of the linear and nonlinear properties of the mode by a combination of strong toroidal effects and low resistivity is the focus of this work. Linearly there is a transition from resistive kink to resistive tearing behavior as the aspect ratio and resistivity are reduced, and there is a corresponding modification of the nonlinear behavior, including a slowing of the island growth and development of a Rutherford regime, as the tearing regime is approached. In order to study the sensitivity of the stability and evolution to assumptions concerning the equation of state, two sets of full nonlinear resistive MHD equations (a pressure convection set and an incompressible set) are used. Both sets give more stable nonlinear behavior as the aspect ratio is reduced. The pressure convection set shows a transition from a Kadomtsev reconnection at large aspect ratio to a saturation at small aspect ratio. The incompressible set yields Kadomtsev reconnection for all aspect ratios, but with a significant lengthening of the reconnection time and development of a Rutherford regime at an aspect ratio approaching the transition from a resistive kink mode to a tearing mode. The pressure convection set gives an incomplete reconnection similar to that sometimes seen experimentally. The pressure convection set is, however, strictly justified only at high beta

Resistive instabilities in general toroidal plasma configurations

International Nuclear Information System (INIS)

Glasser, A.H.; Greene, J.M.; Johnson, J.L.

1975-01-01

Previous work by Johnson and Greene on resistive instabilities is extended to finite-pressure configurations. The Mercier criterion for the stability of the ideal magnetohydrodynamic interchange mode is rederived, the generalization of the earlier stability criterion for the resistive interchange mode is obtained, and a relation between the two is noted. Conditions for tearing mode instability are recovered with the growth rate scaling with the resistivity in a more complicated manner than eta 3 / 5 . Nyquist techniques are used to show that favorable average curvature can convert the tearing mode into an overstable mode and can often stabilize it

Antibiotic resistance increases with local temperature

Science.gov (United States)

MacFadden, Derek R.; McGough, Sarah F.; Fisman, David; Santillana, Mauricio; Brownstein, John S.

2018-06-01

Bacteria that cause infections in humans can develop or acquire resistance to antibiotics commonly used against them1,2. Antimicrobial resistance (in bacteria and other microbes) causes significant morbidity worldwide, and some estimates indicate the attributable mortality could reach up to 10 million by 20502-4. Antibiotic resistance in bacteria is believed to develop largely under the selective pressure of antibiotic use; however, other factors may contribute to population level increases in antibiotic resistance1,2. We explored the role of climate (temperature) and additional factors on the distribution of antibiotic resistance across the United States, and here we show that increasing local temperature as well as population density are associated with increasing antibiotic resistance (percent resistant) in common pathogens. We found that an increase in temperature of 10 °C across regions was associated with an increases in antibiotic resistance of 4.2%, 2.2%, and 2.7% for the common pathogens Escherichia coli, Klebsiella pneumoniae and Staphylococcus aureus. The associations between temperature and antibiotic resistance in this ecological study are consistent across most classes of antibiotics and pathogens and may be strengthening over time. These findings suggest that current forecasts of the burden of antibiotic resistance could be significant underestimates in the face of a growing population and climate change4.

Turbulent Motion of Liquids in Hydraulic Resistances with a Linear Cylindrical Slide-Valve

Directory of Open Access Journals (Sweden)

C. Velescu

2015-01-01

Full Text Available We analyze the motion of viscous and incompressible liquids in the annular space of controllable hydraulic resistances with a cylindrical linear slide-valve. This theoretical study focuses on the turbulent and steady-state motion regimes. The hydraulic resistances mentioned above are the most frequent type of hydraulic resistances used in hydraulic actuators and automation systems. To study the liquids’ motion in the controllable hydraulic resistances with a linear cylindrical slide-valve, the report proposes an original analytic method. This study can similarly be applied to any other type of hydraulic resistance. Another purpose of this study is to determine certain mathematical relationships useful to approach the theoretical functionality of hydraulic resistances with magnetic controllable fluids as incompressible fluids in the presence of a controllable magnetic field. In this report, we established general analytic equations to calculate (i velocity and pressure distributions, (ii average velocity, (iii volume flow rate of the liquid, (iv pressures difference, and (v radial clearance.

Influence of sputtering gas pressure on properties of transparent conducting Si-doped zinc oxide films

Energy Technology Data Exchange (ETDEWEB)

Qin, Hua; Liu, Hunfa; Lei, Chengxin [Shandong Univ. of Technology, Zibo (China). Dept. of Sciences

2013-10-15

Si-doped zinc oxide (SZO, Si 3%) thin films were deposited on glass substrates by means of direct current magnetron sputtering under different pressures. The influence of sputtering pressure on structure, morphology, optical and electrical properties of SZO thin films was investigated. The results reveal that the sputtering pressures have a significant impact on the growth rate, crystal quality and electrical properties of the films, but have little impact on the optical properties of the films. SZO thin film samples grown on glasses are polycrystalline with a hexagonal wurtzite structure and have a preferred orientation along the c-axis perpendicular to the substrate. When the sputtering pressure increases from 2 to 8 Pa, the film surface becomes compact and smooth, the degree of crystallization of the films increases, and the resistivity of films decreases. However, when the sputtering pressure continues to increase from 8 to 10 Pa, the degree of crystallization of the films decreases, the grain size decreases, and the resistivity of the films increases. SZO(3%) thin film deposited at a sputtering pressure of 8 Pa shows the largest carrier concentration, the largest mobility, the lowest resistivity of 3.0 x 10{sup -4} {Omega} cm and a high overall transmission of 93.3% in the visible range. (orig.)

Real-Time Pore Pressure Detection: Indicators and Improved Methods

Directory of Open Access Journals (Sweden)

Jincai Zhang

2017-01-01

Full Text Available High uncertainties may exist in the predrill pore pressure prediction in new prospects and deepwater subsalt wells; therefore, real-time pore pressure detection is highly needed to reduce drilling risks. The methods for pore pressure detection (the resistivity, sonic, and corrected d-exponent methods are improved using the depth-dependent normal compaction equations to adapt to the requirements of the real-time monitoring. A new method is proposed to calculate pore pressure from the connection gas or elevated background gas, which can be used for real-time pore pressure detection. The pore pressure detection using the logging-while-drilling, measurement-while-drilling, and mud logging data is also implemented and evaluated. Abnormal pore pressure indicators from the well logs, mud logs, and wellbore instability events are identified and analyzed to interpret abnormal pore pressures for guiding real-time drilling decisions. The principles for identifying abnormal pressure indicators are proposed to improve real-time pore pressure monitoring.

Radiation-resistance of polyurethane pipes for cooling liquid in BES III

International Nuclear Information System (INIS)

Li Xunfeng; Zheng Lifang; Ji Quan; Wu Ping; Wang Li

2009-01-01

Gamma ray radiation and neutron radiation are predominant in the working conditions of BES III, and the radiation-resistance aging of polyurethane pipes is very important in this condition, as the pipes of cooling liquid for beam pipe and SCQ (superconducting quadrupole) vacuum pipe in BESIII. Polyester polyurethane pipes and polyether polyurethane pipes were irradiated by gamma ray and neutron. The radiation doses were as much as ten years' doses in BES. Pressure test, FTIR and thermal analysis were used to study the radiation-resistance of these two kinds of polyurethane pipes. The results show that the radiation-resistance and thermal stability of polyester polyurethane pipes are prior to those of polyether polyurethane pipes, and the pressure resistance of polyester polyurethane pipes is almost maintained after the irradiation by gamma ray and neutron, but the polyether polyurethane pipes can be aged and ruptured after the irradiation by neutron. (authors)

Metal-insulator transition in n-InSb under high hydrostatic pressure

International Nuclear Information System (INIS)

Schaller, U.; Kraak, W.; Herrmann, R.

1984-01-01

The effect of applying hydrostatic compression (up to 12 kbar) to the galvanomagnetic properties of pure n-InSb crystals is investigated in order to get information about the influence of hydrostatic pressure on the localization of carriers and about the metal-insulator transition. Electrical resistivity and Hall coefficient are measured as a function of pressure for various excess donor concentrations as well as a function of temperature for various pressures

Wind pressure testing of tornado safe room components made from wood

Science.gov (United States)

Robert Falk; Deepak Shrestha

2016-01-01

To evaluate the ability of a wood tornado safe room to resist wind pressures produced by a tornado, two safe room com-ponents were tested for wind pressure strength. A tornado safe room ceiling panel and door were static-pressure-tested according to ASTM E 330 using a vacuum test system. Re-sults indicate that the panels had load capacities from 2.4 to 3.5 times that...

New pastes with high gauge factor for piezoresistive pressure sensors

International Nuclear Information System (INIS)

Szczepanski, Z.; Kalenik, J.; Gonciara, P.; Jakubowska, M.

1999-01-01

The thick film resistors with gauge factor exhibit high reversible changes of resistance under the influence of external load. The piezoresistivity of thick film resistors is utilized in piezoresistive pressure sensors as well as sensors, those allow force detection. The results of studies concerning piezoresistivity in thick film resistors made of pastes elaborated by the authors are presented in this paper. The GF measurement method has been designed and several resistive pastes were tested. The values of gauge factor for these resistive compositions have been evaluated and piezoresistive properties were compared with ESL resistive composition designed for sensor application. (author)

Modeling of Natural Self-Pressurized Circulation Circuits

International Nuclear Information System (INIS)

Zanocco, Pablo; Gimenez, Marcelo; Delmastro, Dario

2003-01-01

In this work, HUARPE code models for self-pressurized two-phase natural convection systems are improved.A drift-flux model is included, allowing the modeling of the relative velocity between phases.The model of steam dome structures is improved, with a thermal resistance scheme, in order to model the material thermal conductivity.This allows improving thermal losses modeling and structures dynamic.'Shape functions' are implemented based on analytic solutions for pressure derivative and density in each node, which allows less diffusive solving schemes, more appropriate for analyzing cases involving density waves phenomena.Finally, pressure evolutions during a pressurization transient are analyzed, comparing the new models and the previous version results.These results are also checked against RELAP code ones, obtained with different dome nodalizations. Moreover, modeling problems are analyzed for each case

Exercise Training for Blood Pressure: A Systematic Review and Meta?analysis

OpenAIRE

Cornelissen, Veronique A.; Smart, Neil A.

2013-01-01

Background We conducted meta?analyses examining the effects of endurance, dynamic resistance, combined endurance and resistance training, and isometric resistance training on resting blood pressure (BP) in adults. The aims were to quantify and compare BP changes for each training modality and identify patient subgroups exhibiting the largest BP changes. Methods and Results Randomized controlled trials lasting ?4 weeks investigating the effects of exercise on BP in healthy adults (age ?18 year...

Effects of transcutaneous electrical nerve stimulation (TENS) on arterial stiffness and blood pressure in resistant hypertensive individuals: study protocol for a randomized controlled trial.

Science.gov (United States)

Vilela-Martin, José Fernando; Giollo-Junior, Luiz Tadeu; Chiappa, Gaspar Rogério; Cipriano-Junior, Gerson; Vieira, Paulo José Cardoso; dos Santos Ricardi, Fábio; Paz-Landim, Manoel Ildefonso; de Andrade, Days Oliveira; Cestário, Elizabeth do Espírito Santo; Cosenso-Martin, Luciana Neves; Yugar-Toledo, Juan Carlos; Cipullo, José Paulo

2016-03-29

Resistant hypertension (RH) treatment requires an adequate and intense therapeutic approach. However, the results are not always satisfactory despite intensive treatment. Of the different pathophysiological mechanisms involved in the pathogenesis of RH, sympathetic overstimulation and therapies that block the sympathetic system have been widely studied. These approaches, however, are invasive and expensive. Another possible approach is by transcutaneous electrical nerve stimulation (TENS), a noninvasive method that modulates activity by using low-frequency transcutaneous electrical stimulation to inhibit primary afferent pathways. Thus, the current study will evaluate the effect of applying TENS in the cervicothoracic region of subjects with RH and will seek to develop a new low-cost and readily available therapy to treat this group of hypertensive individuals. This is a randomized, single blind (subject), parallel-assignment study controlled with a sham group and including participants aged 40 to 70 years with resistant hypertension. The trial has two arms: the treatment and control (sham group). The treatment group will be submitted to the stimulation procedure (TENS). The sham group will not be submitted to stimulation. The primary outcomes will be a reduction in the peripheral blood pressure and adverse events. The secondary outcomes will be a reduction the central blood pressure. The study will last 30 days. The sample size was calculated assuming an alpha error of 5 % to reject the null hypothesis with a statistical power of 80 %, thereby resulting in 28 participants per group (intervention versus sham). In recent decades, RH has become very common and costly. Adequate control requires several drugs, and in many cases, treatment is not successful. Sympathetic nervous system inhibition by renal denervation and central inhibition have significant effects in reducing BP; however, these treatments are costly and invasive. Another type of sympathetic nervous

The electrogas and electroslag multipass high speed welding of nuclear pressure vessel steels

International Nuclear Information System (INIS)

Eichhorn, F.; Hirsch, P.; Langenbahn, H.W.; Wubbels, B.

1978-01-01

High-speed electroslag and electrogas welding of 15 Mn Ni63 steel plates to achieve high strength and toughness joints for reactor pressure vessels are described. Mechanical testing of overheating-resistant, brittle fracture resistant low alloy steels is discussed. (UK)

Development and evaluation of a HEPA filter for increased strength and resistance to elevated temperature

International Nuclear Information System (INIS)

Gilbert, H.; Bergman, W.; Fretthold, J.K.

1993-01-01

We have completed a preliminary study of an improved HEPA filter for increased strength and resistance to elevated temperature to improve the reliability of the standard deep pleated HEPA filter under accident conditions. The improvements to the HEPA filter consist of a silicone rubber sealant and a new HEPA medium reinforced with a glass cloth. Three prototype filters were built and evaluated for temperature and pressure resistance and resistance to rough handling. The temperature resistance test consisted of exposing the HEPA filter to 1,000 scan (1,700 m 3 /hr) at 700 degrees F (371 degrees C) for five minutes.The pressure resistance test consisted of exposing the HEPA filter to a differential pressure of 10 in. w.g. (2.5 kPa) using a water saturated air flow at 95 degrees F (35 degrees C). For the rough handling test, we used a vibrating machine designated the Q110. DOP filter efficiency tests were performed before and after each of the environmental tests. In addition to following the standard practice of using a separate new filter for each environmental test, we also subjected the same filter to the elevated temperature test followed by the pressure resistance test. The efficiency test results show that the improved HEPA filter is significantly better than the standard HEPA filter. Further studies are recommended to evaluate the improved HEPA filter and to assess its performance under more severe accident conditions

Superconductivity of divalent Chevrel phases at very high pressures

International Nuclear Information System (INIS)

Yao, Y.S.; Guertin, R.P.; Hinks, D.G.; Jorgensen, J.; Capone II, D.W.

1988-01-01

The electrical resistivity and the superconducting transition temperatures were examined for three representative divalent Chevrel phase systems, SnMo 6 S 8 , EuMo 6 S 8 , and BaMo 6 S 8 , as a function of hydrostatic pressure to 2 GPa and in quasihydrostatic pressures to 10 GPa. In all systems, T/sub c/ is depressed to 0 K for sufficiently large pressures. For the Sn- and Eu-based systems, both highly purified samples and samples with controlled oxygen content were used. In an oxygenated SnMo 6 S 8 sample (less than 3% O 2 substituted for the S atoms) the pressure threshold and maximum T/sub c/ are 40% lower than in the pure sample, but for P>3.5 GPa the T/sub c/-P phase diagrams nearly coincide, with T/sub c/ reaching zero at an extrapolated pressure of about 12 GPa. In pure EuMo 6 S 8 , superconductivity appears only above a threshold pressure of about 1 GPa and is depressed to 0 K above 4.5 GPa. In an oxygenated sample the maximum T/sub c/ and the threshold pressure are depressed, and above about 3.5 GPa the T/sub c/-P phase diagrams coincide, as in the Sn-based system, although T/sub c/ is then rapidly depressed to 0 K at about 4.5 GPa. In a highly purified BaMo 6 S 8 sample superconductivity appears above about 2 GPa and is depressed to 0 K at extrapolated pressures above 12 GPa. A full transition to the zero-resistance superconducting state is observed in BaMo 6 S 8 . The data are discussed in terms of a model linking the rhombohedral-to-triclinic structural transition, the superconducting transition temperature, and the role of pressure in suppressing the structural transition

Performance Characterization of Solid Oxide Cells Under High Pressure

DEFF Research Database (Denmark)

Sun, Xiufu; Bonaccorso, Alfredo Damiano; Graves, Christopher R.

2015-01-01

on partial pressures (oxygen, steam and hydrogen) were affected by increasing the pressure. In electrolysis mode at low current density, the performance improvement was counteracted by the increase in open circuit voltage, but it has to be borne in mind that the pressurized gas contains higher molar free......In this work, recent pressurized test results of a planar Ni- YSZ (YSZ: Yttria stabilized Zirconia) supported solid oxide cell are presented. Measurements were performed at 800 C in both fuel cell and electrolysis mode at different pressures. A comparison of the electrochemical performance...... of the cell at 1 and 3 bar shows a significant and equal performance gain at higher pressure in both fuel cell mode and electrolysis mode. Electrochemical impedance spectroscopy revealed that the serial resistance was not affected by the operation pressure; all the other processes that are dependent...

Examination of Electrical Resistance of Carburizers Used for Cast Iron Production

Directory of Open Access Journals (Sweden)

Książek D.

2016-12-01

Full Text Available The publication presents the results of examination of selected carburizers used for cast iron production with respect to their electric resistance. Both the synthetic graphite carburizers and petroleum coke (petcoke carburizers of various chemical composition were compared. The relationships between electrical resistance of tested carburizers and their quality were found. The graphite carburizers exhibited much better conductivity than the petcoke ones. Resistance characteristics were different for the different types of carburizers. The measurements were performed according to the authors’ own method based on recording the electric current flow through the compressed samples. The samples of the specified diameter were put under pressure of the gradually increased value (10, 20, 50, 60, and finally 70 bar, each time the corresponding value of electric resistance being measured with a gauge of high accuracy, equal to 0.1μΩ. The higher pressure values resulted in the lower values of resistance. The relation between both the thermal conductance and the electrical conductance (or the resistance is well known and mentioned in the professional literature. The results were analysed and presented both in tabular and, additionally, in graphic form.

Pressure-induced valence change and moderate heavy fermion state in Eu-compounds

Science.gov (United States)

Honda, Fuminori; Okauchi, Keigo; Sato, Yoshiki; Nakamura, Ai; Akamine, Hiromu; Ashitomi, Yosuke; Hedo, Masato; Nakama, Takao; Takeuchi, Tetsuya; Valenta, Jaroslav; Prchal, Jiri; Sechovský, Vladimir; Aoki, Dai; Ōnuki, Yoshichika

2018-05-01

A pressure-induced valence transition has attracted much attention in Eu-compounds. Among them, EuRh2Si2, EuNi2Ge2, and EuCo2Ge2 reveal the valence transition around 1, 2, and 3 GPa, respectively. We have succeeded in growing single crystals of EuT2X2 (T: transition metal, X: Si, Ge) and studied electronic properties under pressure. EuRh2Si2 indicates a first-order valence transition between 1 and 2 GPa, with a large and prominent hysteresis in the electrical resistivity. At higher pressures, the first-order valence transition changes to a cross-over regime with an intermediate valence state. Tuning of the valence state with pressure is reflected in a drastic change of the temperature dependence of the electrical resistivity in EuRh2Si2 single crystals. Effect of pressure on the valence states on EuRh2Si2, EuIr2Si2, EuNi2Ge2, and EuCo2Ge2, as well as an isostructural related compound EuGa4, are reviewed.

A passive quantitative measurement of airway resistance using depth data.

Science.gov (United States)

Ostadabbas, Sarah; Bulach, Christoph; Ku, David N; Anderson, Larry J; Ghovanloo, Maysam

2014-01-01

The Respiratory Syncytial Virus (RSV) is the most common cause of serious lower respiratory tract infections in infants and young children. RSV often causes increased airway resistance, clinically detected as wheezing by chest auscultation. In this disease, expiratory flows are significantly reduced due to the high resistance in patient's airway passages. A quantitative method for measuring resistance can have a great benefit to diagnosis and management of children with RSV infections as well as with other lung diseases. Airway resistance is defined as the lung pressure divided by the airflow. In this paper, we propose a method to quantify resistance through a simple, non-contact measurement of chest volume that can act as a surrogate measure of the lung pressure and volumetric airflow. We used depth data collected by a Microsoft Kinect camera for the measurement of the lung volume over time. In our experimentation, breathing through a number of plastic straws induced different airway resistances. For a standard spirometry test, our volume/flow estimation using Kinect showed strong correlation with the flow data collected by a commercially-available spirometer (five subjects, each performing 20 breathing trials, correlation coefficient = 0.88, with 95% confidence interval). As the number of straws decreased, emulating a higher airway obstruction, our algorithm was sufficient to distinguish between several levels of airway resistance.

Low temperature magnetoresistance in La1.32Sr1.68Mn2O7 layered manganite under hydrostatic pressure

International Nuclear Information System (INIS)

Kumaresavanji, M.; Fontes, M.B.

2010-01-01

The La 1.32 Sr 1.68 Mn 2 O 7 layered manganite system has been studied by the low temperature electrical resistance and magnetoresistance under hydrostatic pressure up to 25 kbar. We have observe both, a Curie temperature (T C ) and a metal-insulator transition (T MI ) at 118 K in the ambient pressure. The applied pressure shifts the T MI to higher temperature values and induces a second metal-insulator transition (T 2 MI ) at 90 K, in the temperature dependence of resistivity measurements. Also, the pressure suppresses the peak resistance abruptly at T C . When an external field of 5 T is applied, we have observed a large negative magnetoresistance of 300% at the transition temperature and a 128% at 4.5 K. However, the increased pressure decreases the magnetoresistance ratio gradually. When the pressure reaches its maximum available value of 25 kbar, the magnetoresistance ratio decreases at a rate of 1.3%/kbar. From our experimental results, the decrease of magnetoresistance ratio with pressure is explained by the pressure induced canted spin state which is not favor for the spin polarized intergrain tunneling in layered manganites.

Effects of compressibility on the resistive ballooning mode

International Nuclear Information System (INIS)

Hender, T.C.; Carreras, B.A.; Cooper, W.A.; Holmes, J.A.; Diamond, P.H.; Similon, P.L.

1983-09-01

The linear stability of the resistive ballooning mode, as described by the resistive MHD model, is investigated both analytically and numerically. When the pressure evolution is approximated by fluid convection (reduced MHD model), an instability driven by geodesic curvature, with a growth rate γ approx. eta/sup 1/3/β/sub rho//sup 2/3/, is found. For conditions relevant to the Impurity Study Experiment (ISX-B), it is shown that for modest poloidal beta (β/sub rho/ approx. = 1), high current, and relatively high temperatures, compressibility has a significant stabilizing influence, relative to the pressure convection model, for low toroidal mode number modes. However, at high β/sub rho/ (greater than or equal to 2), low current, and lower temperatures, compressibility has much less effect

Effect of Pressure on the Ferromagnetic Cerium Compound CeCu9Sn4

International Nuclear Information System (INIS)

Ishii, Y.; Mori, N.; Hedo, M.; Uwatoko, Y.

2003-01-01

Electrical resistivity measurements under hydrostatic pressure up to 2.2 GPa was carried out for a ferromagnetic ternary cerium compound CeCu 9 Sn 4 . The ferromagnetic transition temperature increases with increasing pressure up to 0.8 GPa and then decreases with increasing pressure above 1 GPa. Origins of this pressure dependence may be the competition between magnetic interaction in the c-plane and along the c-direction. (author)

High-pressure study of the non-Fermi liquid material U2Pt2In

International Nuclear Information System (INIS)

Estrela, P.; Visser, A. de; Boer, F.R. de; Pereira, L.C.J.

2001-01-01

The effect of hydrostatic pressure (p≤1.8 GPa) on the non-Fermi liquid state of U 2 Pt 2 In is investigated by electrical resistivity measurements in the temperature interval 0.3-300 K. The experiments were carried out on single-crystals with the current along (I parallel c) and perpendicular (I parallel a) to the tetragonal axis. The pressure effect is strongly current-direction dependent. For I parallel a we observe a rapid recovery of the Fermi-liquid T 2 -term with pressure. A comparison of the data with the magnetotransport theory of Rosch provides evidence for the location of U 2 Pt 2 In at an antiferromagnetic quantum critical point. For I parallel c the resistivity increases under pressure, indicating the enhancement of an additional scattering mechanism. (orig.)

Superconductivity in the unconventional high pressure phase bismuth-III

Energy Technology Data Exchange (ETDEWEB)

Semeniuk, Konstantin; Brown, Philip; Vasiljkovic, Aleksandar; Grosche, Malte [University of Cambridge (United Kingdom)

2015-07-01

One of the most surprising developments in high pressure research was the realisation that many elements assume very unexpected high pressure structures, described in terms of extremely large or even infinite unit cells. Elemental bismuth, which has been known to undergo a series of pressure induced structural transitions between 25 kbar and 80 kbar, is an interesting example: the intermediate pressure Bi-III phase has a complex 'host-guest' structure consisting of two incommensurate sublattices. Since the unit cell is infinitely large, the description of electronic and lattice excitations is problematic. Apart from its metallic character and the observation of superconductivity at low temperature, little is known about the electronic structure in this phase. We investigate the electrical resistivity within the metallic Bi-III phase under high hydrostatic pressure and in applied magnetic field using a piston cylinder cell. Superconductivity is observed below 7.1 K, and we extract the temperature dependence of the upper critical field, which exceeds 2 T at low temperature. The normal state resistivity exhibits an approximately linear temperature dependence. This could be attributed to strong scattering from low-lying excitations, as caused by an unusually soft phonon spectrum. The results suggest that strong coupling superconductivity arises within the host-guest structure of Bi-III out of an unusual electronic state.

Measures of total stress-induced blood pressure responses are associated with vascular damage.

Science.gov (United States)

Nazzaro, Pietro; Seccia, Teresa; Vulpis, Vito; Schirosi, Gabriella; Serio, Gabriella; Battista, Loredana; Pirrelli, Anna

2005-09-01

The role of cardiovascular reactivity to study hypertension, and the assessment methods, are still controversial. We aimed to verify the association of hypertension and vascular damage with several measures of cardiovascular response. We studied 40 patients with normal-high (132 +/- 1/87 +/- 1 mm Hg) blood pressure (Group 1) and 80 untreated hypertensive subjects. Postischemic forearm vascular resistance (mFVR) served to differentiate hypertensive subjects (142 +/- 2/92 +/- 1 mm Hg v 143 +/- 2/94 +/- 2 mm Hg, P = NS) with a lower (Group 2) and higher (Group 3) hemodynamic index of vascular damage (4.8 +/- .05 v 6.3 +/- .09, P blood pressure, heart rate, forearm blood flow, and vascular resistance. Reactivity measures included: a) change from baseline, b) residualized score, c) cumulative change from baseline and residualized score, and d) total reactivity as area-under-the-curve (AUC), including changes occurring during baseline and recovery phases. The AUC of systolic blood pressure, diastolic blood pressure, and mFVR progressively increased in the groups (P AUC of SBP, DBP, and forearm blood flow and resistance demonstrated the highest (P AUC of SBP (beta = 0.634) and forearm blood flow (beta = -0.337) were predictive (P blood pressure stress response, as AUC, including baseline and recovery phases, was significantly better associated with hypertension and vascular damage than the other reactivity measures studied.

Determination of extremely high pressure tolerance of brine shrimp larvae by using a new pressure chamber system.

Science.gov (United States)

Seo, Mihye; Koyama, Sumihiro; Toyofuku, Takashi; Kojima, Shigeaki; Watanabe, Hiromi

2013-11-01

Hydrostatic pressure is the only one of a range of environmental parameters (water temperature, salinity, light availability, and so on) that increases in proportion with depth. Pressure tolerance is therefore essential to understand the foundation of populations and current diversity of faunal compositions at various depths. In the present study, we used a newly developed pressure chamber system to examine changes in larval activity of the salt-lake crustacean, Artemia franciscana, in response to a range of hydrostatic pressures. We showed that A. franciscana larvae were able to survive for a short period at pressures of ≤ 60 MPa (approximately equal to the pressure of 6000 m deep). At a pressure of > 20 MPa, larval motor ability was suppressed, but not lost. Meanwhile, at a pressure of > 40 MPa, some of the larval motor ability was lost without recovery after decompression. For all experiments, discordance of movement and timing between right and left appendages, was observed at pressures of > 20 MPa. Our results indicate that the limit of pressure for sustaining active behavior of A. franciscana larvae is ∼20 MPa, whereas the limit of pressure for survival is within the range 30-60 MPa. Thus, members of the genus Artemia possess the ability to resist a higher range of pressures than their natural habitat depth. Our findings demonstrated an example of an organism capable of invading deeper environment in terms of physical pressure tolerance, and indicate the need and importance of pressure study as an experimental method.

[Safety and short-term efficacy of renal sympathetic denervation in the treatment of resistant hypertension].

Science.gov (United States)

Jiang, Xiong-jing; Liang, Tuo; Dong, Hui; Peng, Meng; Ma, Wen-jun; Guan, Ting; Zhang, Hui-min; Bian, Jin; Xu, Bo; Gao, Run-lin

2012-12-11

Transcatheter renal sympathetic denervation (RDN) is a novel technology/therapy in treating resistant hypertension. The present study aims to evaluate the safety and short-term efficacy of RDN for the treatment of resistant hypertension in a Chinese population. This prospective single-center pilot study was the first one conducted in China with Medtronic Ardian Symplicity Catheter System. Eight patients (6 males and 2 females) with resistant hypertension underwent RDN at our hospital from February to April 2012. All patients were followed up at one month and three months post-RDN. Blood pressure, use of antihypertensive medications, renal function and complications were recorded and analyzed. At one month and three months post-RDN, 24-hour ambulatory blood pressure monitoring showed mean systolic blood pressure and diastolic blood pressure decreased 10 (0 - 18) 13 (3 - 19) and 8 (-2 - 15), 9 (2 - 16) mm Hg throughout 24 hours respectively (P renal function (P > 0.05). No complications were observed. The preliminary results revealed that RDN was safe and effective for the treatment of resistant hypertension in the Chinese population during a 3-month follow-up. Further large and long-term studies are warranted.

Large scale steam flow test: Pressure drop data and calculated pressure loss coefficients

International Nuclear Information System (INIS)

Meadows, J.B.; Spears, J.R.; Feder, A.R.; Moore, B.P.; Young, C.E.

1993-12-01

This report presents the result of large scale steam flow testing, 3 million to 7 million lbs/hr., conducted at approximate steam qualities of 25, 45, 70 and 100 percent (dry, saturated). It is concluded from the test data that reasonable estimates of piping component pressure loss coefficients for single phase flow in complex piping geometries can be calculated using available engineering literature. This includes the effects of nearby upstream and downstream components, compressibility, and internal obstructions, such as splitters, and ladder rungs on individual piping components. Despite expected uncertainties in the data resulting from the complexity of the piping geometry and two-phase flow, the test data support the conclusion that the predicted dry steam K-factors are accurate and provide useful insight into the effect of entrained liquid on the flow resistance. The K-factors calculated from the wet steam test data were compared to two-phase K-factors based on the Martinelli-Nelson pressure drop correlations. This comparison supports the concept of a two-phase multiplier for estimating the resistance of piping with liquid entrained into the flow. The test data in general appears to be reasonably consistent with the shape of a curve based on the Martinelli-Nelson correlation over the tested range of steam quality

Delayed hydride cracking and elastic properties of Excel, a candidate CANDU-SCWR pressure tube material

International Nuclear Information System (INIS)

Pan, Z.L.

2010-01-01

Excel, a Zr alloy which contains 3.5%Sn, 0.8%Nb and 0.8%Mo, shows high strength, good corrosion resistance, excellent creep-resistance and dimension stability and thus is selected as a candidate pressure tube material for CANDU-SCWR. In the present work, the delayed hydride cracking properties (K IH and the DHC growth rates), the hydrogen solubility and elastic modulus were measured in the irradiated and unirradiated Excel pressure tube material. (author)

Return of neonatal CPAP resistance - the Medijet device family examined using in vitro flow simulations.

Science.gov (United States)

Falk, Markus; Donaldsson, Snorri; Jonsson, Baldvin; Drevhammar, Thomas

2017-11-01

Medijet nasal continuous positive airway pressure (CPAP) generators are a family of devices developed from the Benveniste valve. Previous studies have shown that the in vitro performance of the Medijet disposable generator was similar to the Neopuff resistor system. We hypothesised that resistance would be the main mechanism of CPAP generation in the Medijet disposable generator. The in vitro performance of the Medijet reusable and disposable systems, the Neopuff resistor system and the Benveniste and Infant Flow nonresistor systems were investigated using static and dynamic bench tests. Large differences in performance were found between the different systems. The disposable Medijet demonstrated high resistance, low pressure stability and high imposed work of breathing. The results also showed that encapsulating the Benveniste valve changed it into a resistor system. The main mechanism of CPAP generation for the disposable Medijet generator was resistance. The Medijet device family showed increasing resistance with each design generation. The high resistance of the Medijet disposable generator could be of great value when examining the clinical importance of pressure stability. Our results suggest that this device should be used cautiously in patients where pressure-stable CPAP is believed to be clinically important. ©2017 Foundation Acta Paediatrica. Published by John Wiley & Sons Ltd.

Selection for chlorpyrifos resistance in Liriomyza sativae Blanchard: Cross-resistance patterns, stability and biochemical mechanisms.

Science.gov (United States)

Askari-Saryazdi, Ghasem; Hejazi, Mir Jalil; Ferguson, J Scott; Rashidi, Mohammad-Reza

2015-10-01

The vegetable leafminer (VLM), Liriomyza sativae (Diptera: Agromyzidae) is a serious pest of vegetable crops and ornamentals worldwide. In cropping systems with inappropriate management strategies, development of resistance to insecticides in leafminers is probable. Chlorpyrifos is a commonly used pesticide for controlling leafminers in Iran, but resistance to this insecticide in leafminers has not been characterized. In order to develop strategies to minimize resistance in the field and greenhouse, a laboratory selected chlorpyrifos resistant strain of L. sativae was used to characterize resistance and determine the rate of development and stability of resistance. Selecting for resistance in the laboratory after 23 generations yielded a chlorpyrifos resistant selected strain (CRSS) with a resistance ratio of 40.34, determined on the larval stage. CRSS exhibited no cross-resistance to other tested insecticides except for diazinon. Synergism and biochemical assays indicated that esterases (EST) had a key role in metabolic resistance to chlorpyrifos, but glutathione S-transferase (GST) and mixed function oxidase (MFO) were not mediators in this resistance. In CRSS acetylcholinesterase (AChE) was more active than the susceptible strain, Sharif (SH). AChE in CRSS was also less sensitive to inhibition by propoxur. The kinetics parameters (Km and Vmax) of AChE indicated that affinities and hydrolyzing efficiencies of this enzyme in CRSS were higher than SH. Susceptibility to chlorpyrifos in L. sativae was re-gained in the absence of insecticide pressure. Synergism, biochemical and cross-resistance assays revealed that overactivity of metabolic enzymes and reduction in target site sensitivity are probably joint factors in chlorpyrifos resistance. An effective insecticide resistance management program is necessary to prevent fast resistance development in crop systems. Copyright © 2015 Elsevier Inc. All rights reserved.

Spatio-temporal evolution of apparent resistivity during coal-seam hydraulic flushing

Science.gov (United States)

Li, Dexing; Wang, Enyuan; Song, Dazhao; Qiu, Liming; Kong, Xiangguo

2018-06-01

Hydraulic flushing in gas predrainage is widely used, but the hydraulic-flushing effect is evaluated in a traditional way, by determining the desorption volume, moisture content, gas drainage rate and other conventional indices. To verify the rationality and feasibility of the multielectrode resistivity method in the evaluation of coal-seam hydraulic flushing and to research the spatio-temporal evolution of apparent resistivity during hydraulic flushing, a field test was conducted in 17# coal seam at Nuodong Mine, Guizhou. During hydraulic flushing, four stages were defined according to the variation in coal rock resistivity with time, namely, the preparation stage, the sharply decreasing stage, the rapidly increasing stage and the steady stage. The apparent resistivity of the coal rock mass is affected mainly by its own degree of fragmentation and flushing volume. A more serious rupture and a greater flushing volume yield a smaller apparent resistivity during the sharply decreasing stage and a higher resistivity during the stable stage. After three months of gas predrainage, the residual gas content and the gas pressure at different points in the expected affected area decrease below the critical value. Changes in the residual gas content and gas pressure at these points are consistent with the apparent resistivity, which validates the rationality and feasibility of the multielectrode resistivity method in evaluating coal-seam hydraulic flushing.

Characterization of microbial community and antibiotic resistance genes in activated sludge under tetracycline and sulfamethoxazole selection pressure

International Nuclear Information System (INIS)

Zhang, Yingying; Geng, Jinju; Ma, Haijun; Ren, Hongqiang; Xu, Ke; Ding, Lili

2016-01-01

To investigate the microbial community characteristics, antibiotic resistance genes (ARGs), and bioreactor effluent quality change under tetracycline (TC) and sulfamethoxazole (SMX) selection pressure, sequencing batch reactors (SBRs) were used with environmentally relevant concentration and high-level of TC and SMX concentrations (0, 5 ppb, 50 ppb and 10 ppm). Chemical oxygen demand (COD) and ammonia nitrogen (NH_4"+−N) removals appeared unchanged (p > 0.05) with 5 and 50 ppb, but decreased significantly with 10 ppm (p tetG > sul2 > tetA > intI1 > tetS > tetC. Pearson correlation analysis showed most ARGs (tetA, tetC, tetG, tetK, tetM, sul1) were significantly correlated with intI1 (p < 0.01). - Highlights: • COD and NH_4"+−N removals significantly decrease under 10 ppm TC or SMX. • Activated sludge EPS concentrations increase with increasing TC or SMX concentrations. • TC and SMX affect the microbial community diversity of activated sludge. • Actinobacteria abundances increase with increase of TC or SMX concentration. • ARGs abundance increases with addition of TC or SMX.

Surface resistivity measurement of plasma treated polymers

International Nuclear Information System (INIS)

Simon, D.; Pigram, P.J.; Liesegang, J.

2000-01-01

Full text: Resistivity of insulators is an important property of materials used within the integrated circuit and packaging industries. The measurement of electrical resistivity of insulator materials in the surface region in this work is interpreted through observations of surface charge decay. A self-field driven and diffusion charge transport theory is used to model the process and resistivity values obtained computationally. Data for the charge decay of surface charged samples are collected by suspending them inside a coaxial cylinder connected to an electrometer. Samples used have been low density polyethylene LDPE sheet, both pristine and surface treated. Some samples have been treated by air plasma at low vacuum pressures for different periods of time; others have been washed in ethyl acetate and then plasma treated before the resistivity measurement. The sets of resistivity measurements form the various treatments are compared below. X-ray photoelectron spectroscopy (XPS) has also been used to investigate and account for the observed variations in surface resistivity

Study on transport safety of fresh MOX fuel. Performance of the cladding tube of fresh MOX fuel against external water pressure

International Nuclear Information System (INIS)

Ito, Chihiro

1999-01-01

It is important to know the ability of the cladding tube for fresh MOX fuel against external water pressure when they were hypothetically sunk into the sea for unknown reasons. In order to evaluate the ability of cladding tubes for MOX fresh fuel against external water pressure, external water pressure tests were carried out. Resistible limit of cladding tubes against external water pressure is defined when cladding tubes are deformed largely due to buckling etc. The test results show cladding tube of BWR type can resist an external water pressure of 69 MPa (a depth of water of 7,000 m) and that of PWR type fuel can resist an external water pressure of 54 MPa (a depth of water of 5,500 m). Moreover, leak tightness is maintained at an external water pressure of 73 MPa (a depth of water of 7,400 m) for BWR type cladding tubes and at an external water pressure of 98 MPa (a depth of water of 10,000 m) for PWR type cladding tubes. (author)

Coke fouling monitoring by electrical resistivity

Energy Technology Data Exchange (ETDEWEB)

Bombardelli, Clovis; Mari, Livia Assis; Kalinowski, Hypolito Jose [Universidade Tecnologica Federal do Parana (UTFPR), Curitiba, PR (Brazil). Programa de Pos-Graduacao em Engenharia Eletrica e Informatica Industrial (CPGEI)

2008-07-01

An experimental method to simulate the growth of the coke fouling that occurs in the oil processing is proposed relating the thickness of the encrusted coke to its electrical resistivity. The authors suggest the use of the fouling electrical resistivity as a transducer element for determining its thickness. The sensor is basically two electrodes in an electrically isolated device where the inlay can happen in order to compose a purely resistive transducer. Such devices can be easily constructed in a simple and robust form with features capable to face the high temperatures and pressures found in relevant industrial processes. For validation, however, it is needed a relationship between the electrical resistivity and the fouling thickness, information not yet found in the literature. The present work experimentally simulates the growth of a layer of coke on an electrically insulating surface, equipped with electrodes at two extremities to measure the electrical resistivity during thermal cracking essays. The method is realized with a series of consecutive runs. The results correlate the mass of coke deposited and its electrical resistivity, and it can be used to validate the coke depositions monitoring employing the resistivity as a control parameter. (author)

A Statistical Study on the Effect of Hydrostatic Pressure on Metastable Pitting Corrosion of X70 Pipeline Steel.

Science.gov (United States)

Yang, Zixuan; Kan, Bo; Li, Jinxu; Qiao, Lijie; Volinsky, Alex A; Su, Yanjing

2017-11-14

Hydrostatic pressure effects on pitting initiation and propagation in X70 steel are investigated by evaluating metastable pitting probability using electrochemical methods and immersion corrosion tests in containing chlorine ion solution. Potentiodynamic tests indicated that hydrostatic pressure can decrease the breakdown potential and lead to a reduced transpassivity region. Metastable test results revealed that hydrostatic pressure can increase metastable pitting formation frequency and promote stabilization of metastable pitting growth. Electrochemical impedance spectroscopy (EIS) results indicate that Hydrostatic pressure decreases the charge transfer resistance and increases the dissolution rate within the cavities. Corrosion test results also indicated that pitting initiation and propagation are accelerated by hydrostatic pressure. Result validity was verified by evaluating metastable pitting to predict pitting corrosion resistance.

Numerical methods in simulation of resistance welding

DEFF Research Database (Denmark)

Nielsen, Chris Valentin; Martins, Paulo A.F.; Zhang, Wenqi

2015-01-01

Finite element simulation of resistance welding requires coupling betweenmechanical, thermal and electrical models. This paper presents the numerical models and theircouplings that are utilized in the computer program SORPAS. A mechanical model based onthe irreducible flow formulation is utilized...... a resistance welding point of view, the most essential coupling between the above mentioned models is the heat generation by electrical current due to Joule heating. The interaction between multiple objects is anothercritical feature of the numerical simulation of resistance welding because it influences...... thecontact area and the distribution of contact pressure. The numerical simulation of resistancewelding is illustrated by a spot welding example that includes subsequent tensile shear testing...

Resistive ballooning modes in W7-AS and W7-X

International Nuclear Information System (INIS)

Kaiser, R.

1993-01-01

'Critical' pressure gradients due to resistive ballooning modes and their growth rates were computed for the W7-AS stellarator and for a HELIAS configuration with W7-X parameters, and the two configurations were compared. The results are based on the evaluation of a fourth order magnetic differential equation along closed magnetic field lines. The numerical procedure applying a variational approach uses the 'Garching resistive ballooning code', GARBO, which was originally developed for the stability analysis of axisymmetric plasmas. Concerning purely growing modes, this analysis shows that the favourable stability properties of W7-X, already optimized with respect to ideal ballooning modes, persist in the resistive regime: the destabilizing effect of resistivity is largely compensated by the stabilizing contribution of plasma compression. As a consequence, the ideal β limit continues only moderately shifted in the resistive case and likewise ideal ballooning stable equilibria (up to β 0 ≅ 5%) do not become resistively unstable. The situation is different for W7-AS. Greater resistive effects (in comparison with W7-X) are found in a configuration that is already ideally much more unstable. A basic feature in resistive calculations is the occurrence of overstable modes. These modes no longer show a stability threshold and, for realistic values of pressure and resistivity, linear instability is obtained for W7-AS as well as for W7-X, with growth rates and oscillation frequencies in the kilo-Hertz range. (author). 29 refs, 13 figs

Influence of temperature and pressure on the lethality of ultrasound

International Nuclear Information System (INIS)

Raso, J.; Pagan, R.; Condon, S.; Sala, F.J.

1998-01-01

A specially designed resistometer was constructed, and the lethal effect on Yersinia enterocolitica of ultrasonic waves (UW) at different static pressures (manosonication [MS]) and of combined heat-UW under pressure treatments (manothermosonication [MTS]) was investigated. During MS treatments at 30 degrees C and 200 kPa, the increase in the amplitude of UW of 20 kHz from 21 to 150 micrometers exponentially decreased decimal reduction time values (D(MS)) from 4 to 0.37 min. When pressure was increased from 0 to 600 kPa at a constant amplitude (150 micrometers) and temperature (30 degrees C), D(MS) values decreased from 1.52 to 0.20 min. The magnitude of this decrease in D(MS) declined progressively as pressure was increased. The influence of pressure on D(MS) values was greater with increased amplitude of UW. Pressure alone of as much as 600 kPa did not influence the heat resistance of Y. enterocolitica (D60 = 0.094; zeta = 5.65). At temperatures of as much as 58 degrees C, the lethality of UW under pressure was greater than that of heat treatment alone at the same temperature. At higher temperatures, this difference disappeared. Heat and UW under pressure seemed to act independently. The lethality of MTS treatments appeared to result from the added effects of UW under pressure and the lethal effect of heat. The individual contributions of heat and of UW under pressure to the total lethal effect of MTS depended on temperature. The inactivating effect of UW was not due to titanium particles eroded from the sonication horn. The addition to the MS media of cysteamine did not increase the resistance of Y. enterocolitica to MS treatment. MS treatment caused cell disruption

Effect of pressure on spin fluctuations and superconductivity in heavy-fermion UPt3

International Nuclear Information System (INIS)

Willis, J.O.; Thompson, J.D.; Fisk, Z.; de Visser, A.; Franse, J.J.M.; Menovsky, A.

1985-01-01

We have determined the effect of hydrostatic pressure on the susceptibility, on the T 2 temperature dependence of the spin-fluctuation resistivity, and on superconductivity in UPt 3 . The spin-fluctuation temperature T/sub s/, derived from the slope of resistivity versus T 2 , is used within a Fermi-liquid picture to calculate the susceptibility chi at T = 0 K. The depression of this calculated chi with pressure agrees with the directly measured value partial lnchi/partialP = -24 Mbar -1 . Both the superconducting transition temperature T/sub c/ and the initial slope of the upper critical field also decrease under pressure. We find that partial lnT/sub c//partialP = -25 Mbar -1 and speculate upon correlations between chi and T/sub c/

Pressure effect on the superconducting and the normal state of β -B i2Pd

Science.gov (United States)

Pristáš, G.; Orendáč, Mat.; Gabáni, S.; Kačmarčík, J.; Gažo, E.; Pribulová, Z.; Correa-Orellana, A.; Herrera, E.; Suderow, H.; Samuely, P.

2018-04-01

The pressure effect up to 24.0 kbar on superconducting and normal-state properties of β -B i2Pd single crystal (Tc≈4.98 K at ambient pressure) has been investigated by measurements of the electrical resistivity. In addition, we have performed the heat capacity measurements in the temperature range 0.7-300 K at ambient pressure. The recent calculations of electronic density of states, electron-phonon interaction spectral function, and phonon density of states of β -B i2Pd [Zheng and Margine, Phys. Rev. B 95, 014512 (2017), 10.1103/PhysRevB.95.014512], are used to fit the resistivity and the heat capacity data. In the superconducting state we have focused on the influence of pressure on the superconducting transition temperature Tc and upper critical field Hc 2 and a negative effect with d Tc/d p =-0.025 K /kbar and d Hc 2/d p =-8 mT /kbar is found. A simplified Bloch-Grüneisen model was used to analyze the pressure effect on the temperature dependence of the normal-state resistivity. The obtained results point to a decrease of the electron-phonon coupling parameter λ and to a shift of phonon frequencies to higher values with pressure. Moreover, the temperature dependence of the normal-state resistivity follows a T2 dependence above Tc up to about 25 K. Together with the enhanced value of Sommerfeld coefficient γ =13.23 mJ mo l-1K-2 these results point to a certain role of the electron-electron interaction in the superconducting pairing mechanism in β -B i2Pd .

Evolutionary Origin of Antibiotic Resistance, A Historical Perspective

Directory of Open Access Journals (Sweden)

Yamile Adriana Celis Bustos

2017-07-01

Full Text Available Antimicrobial resistance is a natural aspect of bacterial evolution that can result from mutations or acquisition of foreign genes. Various views on the origin of this resistance explain the ability of these organisms to acquire new features. Lamarck andDarwin’s theories of evolution have led to experiments designed to explore the origin of bacterial variation and the emergence of new features. These experiments show that antimicrobial resistance is related to mutations in chromosomal genes and/or transfer of extrachromosomal genetic elements that can be expressed based on the antibiotic pressure exerted. The main experiments and findings that seek to explain the phenomenon of antibiotic resistance are reviewed here in.

Zinc Resistance within Swine-Associated Methicillin-Resistant Staphylococcus aureus Isolates in the United States Is Associated with Multilocus Sequence Type Lineage.

Science.gov (United States)

Hau, Samantha J; Frana, Timothy; Sun, Jisun; Davies, Peter R; Nicholson, Tracy L

2017-08-01

Zinc resistance in livestock-associated methicillin-resistant Staphylococcus aureus (LA-MRSA) sequence type 398 (ST398) is primarily mediated by the czrC gene colocated with the mecA gene, encoding methicillin resistance, within the type V staphylococcal cassette chromosome mec (SCC mec ) element. Because czrC and mecA are located within the same mobile genetic element, it has been suggested that the use of zinc in feed as an antidiarrheal agent has the potential to contribute to the emergence and spread of methicillin-resistant S. aureus (MRSA) in swine, through increased selection pressure to maintain the SCC mec element in isolates obtained from pigs. In this study, we report the prevalence of the czrC gene and phenotypic zinc resistance in U.S. swine-associated LA-MRSA ST5 isolates, MRSA ST5 isolates from humans with no swine contact, and U.S. swine-associated LA-MRSA ST398 isolates. We demonstrated that the prevalence of zinc resistance in U.S. swine-associated LA-MRSA ST5 isolates was significantly lower than the prevalence of zinc resistance in MRSA ST5 isolates from humans with no swine contact and swine-associated LA-MRSA ST398 isolates, as well as prevalences from previous reports describing zinc resistance in other LA-MRSA ST398 isolates. Collectively, our data suggest that selection pressure associated with zinc supplementation in feed is unlikely to have played a significant role in the emergence of LA-MRSA ST5 in the U.S. swine population. Additionally, our data indicate that zinc resistance is associated with the multilocus sequence type lineage, suggesting a potential link between the genetic lineage and the carriage of resistance determinants. IMPORTANCE Our data suggest that coselection thought to be associated with the use of zinc in feed as an antimicrobial agent is not playing a role in the emergence of livestock-associated methicillin-resistant Staphylococcus aureus (LA-MRSA) ST5 in the U.S. swine population. Additionally, our data indicate

Dietary fiber and blood pressure control.

Science.gov (United States)

Aleixandre, A; Miguel, M

2016-04-01

In the past few years, new strategies to control blood pressure levels are emerging by developing new bioactive components of foods. Fiber has been linked to the prevention of a number of cardiovascular diseases and disorders. β-Glucan, the main soluble fiber component in oat grains, was initially linked to a reduction in plasma cholesterol. Several studies have shown afterward that dietary fiber may also improve glycaemia, insulin resistance and weight loss. The effect of dietary fiber on arterial blood pressure has been the subject of far fewer studies than its effect on the above-mentioned variables, but research has already shown that fiber intake can decrease arterial blood pressure in hypertensive rats. Moreover, certain fibers can improve arterial blood pressure when administered to hypertensive and pre-hypertensive subjects. The present review summarizes all those studies which attempt to establish the antihypertensive effects of dietary fiber, as well as its effect on other cardiovascular risk factors.

Effect of fenofibrate on blood pressure reduction

Directory of Open Access Journals (Sweden)

A K Lipatenkova

2013-03-01

Full Text Available Реферат по материалам статей 1. Gilbert K, Nian H, Yu C, Luther JM, Brown NJ. Fenofibrate lowers blood pressure in salt-sensitive but not salt-resistant hypertension. J Hypertens. 2013 Apr;31(4:820-9. doi: 10.1097/HJH.0b013e32835e8227. 2. Kwang K. K. Does Fenofibrate Lower Blood Pressure? Hypertension. 2013 Mar;61(3:e27. doi: 10.1161/HYPERTENSIONAHA.111.00792.

A highly sensitive pressure sensor using a Au-patterned polydimethylsiloxane membrane for biosensing applications

International Nuclear Information System (INIS)

Liu, Xinchuan; Zhu, Yihao; Nomani, Md W; Koley, Goutam; Wen, Xuejun; Hsia, Tain-Yen

2013-01-01

We report on the fabrication and characterization of a highly sensitive pressure sensor using a Au film patterned on a polydimethylsiloxane (PDMS) membrane. The strain-induced change in the film resistance was utilized to perform the quantitative measurement of absolute pressure. The highest sensitivity obtained for a 200 µm thick PDMS film sensor was 0.23/KPa with a range of 50 mm Hg, which is the best result reported so far, over that range, for any pressure sensor on a flexible membrane. The noise-limited pressure resolution was found to be 0.9 Pa (0.007 mm Hg), and a response time of ∼200 ms, are the best reported results for these sensors. The ultrahigh sensitivity is attributed to the strain-induced formation of microcracks, the effect of which on the resistance change was found to be highly reversible within a certain pressure range. A physical model correlating the sensitivity with the sensor parameters and crack geometry has been proposed. (paper)

within plant resistance to water flow in tomato and sweet melons

African Journals Online (AJOL)

Administrator

high pressure flow meter (HPFM) and evaporative flux (EF) methods. In the evaporative flux method, measure- ments of transpiration flux and leaf water potential were used to calculate the total resistance to water flow using. Ohm's law analogy. Measurements of tranpiration flux (Q) relationship, plant resistance calculated ...

Triiodothyronine : a link between the insulin resistance syndrome and blood pressure?

NARCIS (Netherlands)

Bakker, SJL; ter Maaten, JC; Popp-Snijders, C; Heine, RJ; Gans, ROB

1999-01-01

Objective Overall obesity is associated with elevated serum triiodothyronine concentrations and insulin resistance. Oral triiodothyronine is known to induce hypertension in laboratory rats, while triiodothyronine also increases the expression of genes encoding for enzymes involved in the synthesis

Triiodothyronine: a link between the insulin resistance syndrome and blood pressure?

NARCIS (Netherlands)

Bakker, J.L.; ter Maaten, J.C; Popp-Snijders, C.; Heine, R.J.; Gans, R.O.B.

1999-01-01

Objective. Overall obesity is associated with elevated serum triiodothyronine concentrations and insulin resistance. Oral triiodothyronine is known to induce hypertension in laboratory rats, while triiodothyronine also increases the expression of genes encoding for enzymes involved in the synthesis

Novel fabric pressure sensors: design, fabrication, and characterization

International Nuclear Information System (INIS)

Wang, Yangyong; Hua, Tao; Zhu, Bo; Li, Qiao; Yi, Weijing; Tao, Xiaoming

2011-01-01

Soft and pliable pressure sensors are essential elements in wearable electronics which have wide applications in modern daily lives. This paper presents a family of fabric pressure sensors made by sandwiching a piece of resistive fabric strain sensing element between two tooth-structured layers of soft elastomers. The pressure sensors are capable of measuring pressure from 0 to 2000 kPa, covering the whole range of human–machine interactions. A pressure sensitivity of up to 2.98 × 10 −3 kPa −1 was obtained. Theoretical modeling was conducted based on an energy method to predict the load–displacement relationship for various sensor configurations. By adjusting the Young's modulus of the two conversion layers, as well as the geometrical dimensions, the measurement ranges, and sensitivities of the sensors can be quantitatively determined. The sensors are being used for pressure measurements between the human body and garments, shoes, beds, and chairs

HIV Genetic Diversity and Drug Resistance

Science.gov (United States)

Santos, André F.; Soares, Marcelo A.

2010-01-01

Most of the current knowledge on antiretroviral (ARV) drug development and resistance is based on the study of subtype B of HIV-1, which only accounts for 10% of the worldwide HIV infections. Cumulative evidence has emerged that different HIV types, groups and subtypes harbor distinct biological properties, including the response and susceptibility to ARV. Recent laboratory and clinical data highlighting such disparities are summarized in this review. Variations in drug susceptibility, in the emergence and selection of specific drug resistance mutations, in viral replicative capacity and in the dynamics of resistance acquisition under ARV selective pressure are discussed. Clinical responses to ARV therapy and associated confounding factors are also analyzed in the context of infections by distinct HIV genetic variants. PMID:21994646

Pressure-induced spin and charge transport in La1.25Sr1.75Mn2O7 single crystal

International Nuclear Information System (INIS)

Mydeen, K.; Arumugam, S.; Prabhakaran, D.; Yu, R.C.; Jin, C.Q.

2009-01-01

We investigated the effect of uniaxial and hydrostatic pressure on resistivity and ac-magnetic susceptibility of two-dimensional layered manganite, La 1.25 Sr 1.75 Mn 2 O 7 (LSMO125) to investigate the lattice effect on magnetic and electronic properties. Asymmetric role of uniaxial pressure, || and -perpendicular to c-axis on the spin flop and charge transport has been revealed while comparing hydrostatic pressure. Uniaxial pressure along c-axis increases metal-insulator transition temperature (T MI ) and ferromagnetic ordering temperature (T C ), whereas it decreases the resistivity along ab-plane (ρ ab ). In contrast to pressure along c-axis, T MI and T C decrease, whereas the resistivity along c-axis (ρ c ) increases with pressure || to ab-plane. ρ c /ρ ab is quite large, increasing with pressure and shows a peak at around T MI . Uniaxial pressure behaviour is strongly related to the Mn-O-Mn linkage between MnO 2 layers and the spin reorientation from the apical axis to the basal plane and vice versa with pressure. Both ρ ab and ρ c decrease whereas T MI and T C increases under hydrostatic pressure. Influence of spin and charge on magnetic and electrical properties under hydrostatic pressure are explained by pressure-induced cant between the MnO 2 bilayers and variation in bond lengths. The different pressure driving rates of T MI while measuring ρ ab and ρ c confirms that there is a strong competition between the in and out plane components under hydrostatic pressure

Pressure effects on the magnetic and transport properties of the Kondo lattice system Ce3RuSn6

Science.gov (United States)

Wakiya, Kazuhei; Tomaki, Takeru; Kimura, Minami; Uehara, Masatomo; Gouchi, Jun; Uwatoko, Yoshiya; Umehara, Izuru

2018-05-01

The magnetization and electrical resistivity of Ce3RuSn6 have been measured in the temperature range from 2 to 300 K and in the pressure range up to 1 GPa. At ambient pressure, the magnetization shows a ferromagnetic-like steep rise below 4 K. The electrical resistivity drops at TC = 3.3 K due to the magnetic transition. We found that TC is slightly enhanced by applying pressure, suggesting that this compound sits on the left side of the peak in the Doniach phase diagram.

Thermodynamic Resistance to Matter Flow at The Interface of a Porous Membrane.

Science.gov (United States)

Glavatskiy, K S; Bhatia, Suresh K

2016-04-12

Nanoporous materials are important in industrial separation, but their application is subject to strong interfacial barriers to the entry and transport of fluids. At certain conditions the fluid inside and outside the nanoporous material can be viewed as a two-phase system, with an interface between them, which poses an excess resistance to matter flow. We show that there exist two kinds of phenomena which influence the interfacial resistance: hydrodynamic effects and thermodynamic effects, which are independent of each other. Here, we investigate the role of the thermodynamic effects in carbon nanotubes (CNTs) and slit pores and compare the associated thermodynmic resistance with that due to hydrodynamic effects traditionally modeled by the established Sampson expression. Using CH4 and CO2 as model fluids, we show that the thermodynamic resistance is especially important for moderate to high pressures, at which the fluid within the CNT or slit pore is in the condensed state. Further, we show that at such pressures the thermodynamic resistance becomes comparable with the internal resistance to fluid transport at length scales typical of membranes used in fuel cells, and of importance in membrane-based separation, and nanofluidics in general.

Ab initio study of properties of BaBiO3 at high pressure

Science.gov (United States)

Martoňák, Roman; Ceresoli, Davide; Kagayama, Tomoko; Tosatti, Erio

BaBiO3 is a mixed-valence perovskite which escapes metallic state by creating a Bi-O bond disproportionation or CDW pattern, resulting in a Peierls semiconductor with gap of nearly 1 eV at zero pressure. Evolution of structural and electronic properties at high pressure is, however, largely unknown. Pressure, it might be natural to expect, could reduce the bond-disproportionation and bring the system closer to metalicity or even superconductivity. We address this question by ab initio DFT methods based on GGA and hybrid functionals in combination with crystal structure prediction techniques based on genetic algorithms. We analyze the pressure evolution of bond disproportionation as well as other order parameters related to octahedra rotation for various phases in connection with corresponding evolution of the electronic structure. Results indicate that BaBiO3 continues to resist metalization also under pressure, through structural phase transitions which sustain and in fact increase the diversity of length of Bi-O bonds for neighboring Bi ions, in agreement with preliminary high pressure resistivity data. R.M. Slovak Research and Development Agency Contract APVV-15-0496, VEGA project No. 1-0904-15; E.T. ERC MODPHYSFRICT Advanced Grant No. 320796.

Renal sympathetic denervation for resistant hypertension.

Science.gov (United States)

Froeschl, Michael; Hadziomerovic, Adnan; Ruzicka, Marcel

2013-05-01

Resistant hypertension is an increasingly prevalent health problem associated with important adverse cardiovascular outcomes. The pathophysiology that underlies this condition involves increased function of both the sympathetic nervous system and the renin-angiotensin II-aldosterone system. A crucial link between these 2 systems is the web of sympathetic fibres that course within the adventitia of the renal arteries. These nerves can be targeted by applying radiofrequency energy from the lumen of the renal arteries to renal artery walls (percutaneous renal sympathetic denervation [RSD]), an approach that has attracted great interest. This paper critically reviews the evidence supporting the use of RSD. Small studies suggest that RSD can produce dramatic blood pressure reductions: In the randomized Symplicity HTN-2 trial of 106 patients, the mean fall in blood pressure at 6 months in patients who received the treatment was 32/12 mm Hg. However, there are limitations to the evidence for RSD in the treatment of resistant hypertension. These include the small number of patients studied; the lack of any placebo-controlled evidence; the fact that blood pressure outcomes were based on office assessments, as opposed to 24-hour ambulatory monitoring; the lack of longer-term efficacy data; and the lack of long-term safety data. Some of these concerns are being addressed in the ongoing Renal Denervation in Patients With Uncontrolled Hypertension (Symplicity HTN-3) trial. The first percutaneous RSD system was approved by Health Canada in the spring of 2012. But until more and better-quality data are available, this procedure should generally be reserved for those patients whose resistant hypertension is truly uncontrolled. Copyright © 2013 Canadian Cardiovascular Society. Published by Elsevier Inc. All rights reserved.

Efeitos da suplementação de potássio via sal de cozinha sobre a pressão arterial e a resistência à insulina em pacientes obesos hipertensos em uso de diuréticos Effects of potassium supplementation by salt on arterial blood pressure and insulin resistance in hypertensive obese patients on diuretic therapy

Directory of Open Access Journals (Sweden)

Maria Alice de Gouveia Pereira

2005-02-01

Full Text Available OBJETIVO: Avaliar os efeitos da suplementação de potássio, por intermédio do sal de cozinha contendo cloreto de potássio, associada à dieta hipocalórica e à atividade física aeróbica, sobre a pressão arterial e índices de resistência à insulina em pacientes hipertensos com obesidade abdominal. MÉTODOS: Estudo prospectivo duplo-cego, randomizado, em 22 pacientes hipertensos com excesso de peso (índice de massa corporal >27kg/m² e controle insatisfatório da pressão arterial durante o uso de diuréticos pressão arterial sistólica >140 e 90 e OBJECTIVE: The objectives of the present study were to evaluate the effects of oral potassium supplementation, associated with a hypocaloric diet and aerobic exercises, on plasma potassium levels, blood pressure and insulin resistance, in centrally obese, not well controlled hypertensive patients on diuretic therapy; waist to hip ratio >0.85 in women, and >0.95 in men; systolic blood pressure >140mmHg and 90mmHg and <105mmHg. METHODS: This was a prospective double-blind randomized study including 22 patients divided in 2 groups: sodium chloride n=10, and potassium chloride n=12. For 12 weeks, each group received cooking salt containing, either 100% sodium chloride, or 50% sodium chloride and 50% potassium chloride. All patients were submitted to a hypocaloric diet and advised to increase their physical activity; a 40-minute walk three times a week. Before and after the study period, all patients were submitted to determinations of body mass index, body composition, waist circumference, sodium and potassium urinary excretions, sodium and potassium serum levels, 24h ambulatory blood pressure monitoring, oral glucose tolerance test with serum insulin measurements at fasting and 120 minutes after glucose load, and serum lipid profile. RESULTS: In both groups, no changes were observed in serum sodium and potassium levels, in blood glucose and insulin levels, insulin resistance indexes and serum

Genome wide adaptations of Plasmodium falciparum in response to lumefantrine selective drug pressure.

Directory of Open Access Journals (Sweden)

Leah Mwai

Full Text Available The combination therapy of the Artemisinin-derivative Artemether (ART with Lumefantrine (LM (Coartem® is an important malaria treatment regimen in many endemic countries. Resistance to Artemisinin has already been reported, and it is feared that LM resistance (LMR could also evolve quickly. Therefore molecular markers which can be used to track Coartem® efficacy are urgently needed. Often, stable resistance arises from initial, unstable phenotypes that can be identified in vitro. Here we have used the Plasmodium falciparum multidrug resistant reference strain V1S to induce LMR in vitro by culturing the parasite under continuous drug pressure for 16 months. The initial IC(50 (inhibitory concentration that kills 50% of the parasite population was 24 nM. The resulting resistant strain V1S(LM, obtained after culture for an estimated 166 cycles under LM pressure, grew steadily in 378 nM of LM, corresponding to 15 times the IC(50 of the parental strain. However, after two weeks of culturing V1S(LM in drug-free medium, the IC(50 returned to that of the initial, parental strain V1S. This transient drug tolerance was associated with major changes in gene expression profiles: using the PFSANGER Affymetrix custom array, we identified 184 differentially expressed genes in V1S(LM. Among those are 18 known and putative transporters including the multidrug resistance gene 1 (pfmdr1, the multidrug resistance associated protein and the V-type H+ pumping pyrophosphatase 2 (pfvp2 as well as genes associated with fatty acid metabolism. In addition we detected a clear selective advantage provided by two genomic loci in parasites grown under LM drug pressure, suggesting that all, or some of those genes contribute to development of LM tolerance--they may prove useful as molecular markers to monitor P. falciparum LM susceptibility.

Pressure Myography to Study the Function and Structure of isolated small arteries

DEFF Research Database (Denmark)

Schjørring, Olav; Carlsson, Rune; Simonsen, Ulf

2015-01-01

Small arteries play an important role in regulation of peripheral resistance and organ perfusion. Here we describe a series of the methods allowing measurements in pressurized segments of small arteries from the systemic and coronary circulation of mice as well as other species. The pressure...... myography techniques described include measurements of wall structure, wall stress, strain, and of myogenic tone. The pressurized perfused small arteries also allow evaluation of responses to increases in pressure, flow, and drugs, where the main readout is changes in vascular diameter....

Effect of Tire Pressure to Physical Workload at Operating a Manual Wheelchair.

Science.gov (United States)

Booka, Masayuki; Yoneda, Ikuo; Hashizume, Tsutomu; Lee, Hokyoo; Oku, Hidehisa; Fujisawa, Shoichiro

2015-01-01

It is often experienced that low tire pressure of the wheelchair not only increases running resistance, but also reduces parking brake performance. In this study, the required driving forces for different tire pressures were experimentally measured and evaluated. It was indicated from the result that the wheelchair with proper tire pressure could be run with less workload of wheelchair-user. Then it was also indicated that the wheelchair with a lower tire pressure needed more workload of wheelchair-user even on hard level surface.

Characterization of Piezoresistive PEDOT:PSS Pressure Sensors with Inter-Digitated and Cross-Point Electrode Structures