WorldWideScience

Sample records for preparing large volumes

  1. Preparation of High Surface Area, Large Pore Volume Alumina by Using β-Cyclodextrin as a Non-surfactant Template

    Institute of Scientific and Technical Information of China (English)

    Lai Jun WANG; Ming Fen WEN; Yu Shan LI; Dong YANG; Jing CHEN; Chong Li SONG

    2006-01-01

    A series of alumina samples were prepared using β-cyclodextrin as the non-surfactant template. These samples were characterized by XRD, BET and TEM. The results showed that the alumina samples prepared using β-cyclodextrin template had the higher surface areas (124-484 m2/g), larger pore volumes (0.7-1.27 mL/g) and more thermal stability than samples prepared without using β-cyclodextrin.

  2. Large volume cryogenic silicon detectors

    Energy Technology Data Exchange (ETDEWEB)

    Braggio, C. [Dipartimento di Fisica, Universita di Padova, via Marzolo 8, 35131 Padova (Italy); Boscardin, M. [Fondazione Bruno Kessler (FBK), via Sommarive 18, I-38100 Povo (Italy); Bressi, G. [INFN sez. di Pavia, via Bassi 6, 27100 Pavia (Italy); Carugno, G.; Corti, D. [INFN sez. di Padova, via Marzolo 8, 35131 Padova (Italy); Galeazzi, G. [INFN lab. naz. Legnaro, viale dell' Universita 2, 35020 Legnaro (Italy); Zorzi, N. [Fondazione Bruno Kessler (FBK), via Sommarive 18, I-38100 Povo (Italy)

    2009-12-15

    We present preliminary measurements for the development of a large volume silicon detector to detect low energy and low rate energy depositions. The tested detector is a one cm-thick silicon PIN diode with an active volume of 31 cm{sup 3}, cooled to the liquid helium temperature to obtain depletion from thermally-generated free carriers. A thorough study has been done to show that effects of charge trapping during drift disappears at a bias field value of the order of 100V/cm.

  3. Preparation of large monodisperse vesicles.

    Directory of Open Access Journals (Sweden)

    Ting F Zhu

    Full Text Available Preparation of monodisperse vesicles is important both for research purposes and for practical applications. While the extrusion of vesicles through small pores (approximately 100 nm in diameter results in relatively uniform populations of vesicles, extrusion to larger sizes results in very heterogeneous populations of vesicles. Here we report a simple method for preparing large monodisperse multilamellar vesicles through a combination of extrusion and large-pore dialysis. For example, extrusion of polydisperse vesicles through 5-microm-diameter pores eliminates vesicles larger than 5 microm in diameter. Dialysis of extruded vesicles against 3-microm-pore-size polycarbonate membranes eliminates vesicles smaller than 3 microm in diameter, leaving behind a population of monodisperse vesicles with a mean diameter of approximately 4 microm. The simplicity of this method makes it an effective tool for laboratory vesicle preparation with potential applications in preparing large monodisperse liposomes for drug delivery.

  4. Enhanced performance large volume dissolution-DNP

    DEFF Research Database (Denmark)

    Bowen, Sean; Ardenkjær-Larsen, Jan Henrik

    2014-01-01

    A systematic study of the performance of the dissolution process in dissolution-DNP is presented. A relatively simple set of modifications is made to the standard Hypersense dissolution system to enable polarization of large volume samples. These consist of a large volume sample cup along...... with supporting modifications to the dissolution head and related components. Additional modifications were made to support the mapping of the temperature/pressure space of the dissolution process as well as enabling the use of large volumes of solvent and improving the robustness of the system. No loss...

  5. 应用固定砂石总体积法配制大粒径自密实混凝土%Preparation of self-compacting concrete with large diameter aggregate by fixed total volume of sand and gravel

    Institute of Scientific and Technical Information of China (English)

    危加阳; 罗竹容

    2014-01-01

    The method of fixed volume of sand and gravel is commonly used in mixture proportion design of self-compacting concrete. In order to return to the natural properties of aggregate, the method of fixed total volume of sand and gravel that is dif-ferent from the traditional concept is proposed, i. e. , in the mixture proportion design of self-compacting concrete, we should ensure it completely enwrapped, separated and suspended by cementing material. Moreover, this method is also applied in the preparation of self-compacting concrete with the maximum size of 31. 5 mm of coarse aggregate. The practices show that the self-compacting concrete still has good stability of anti-segregation and demonstrates that the preparation of self-compacting con-crete with large diameter aggregate by fixed total volume of sand and gravel is feasible.%固定砂石体积法是设计自密实混凝土配合比的常用方法。为回归骨料的天然属性,提出了有别于传统概念的固定砂石总体积法,即在配制自密实混凝土时,按胶凝材料浆包裹、分隔、悬浮总骨料为目标进行配比计算。同时,在工程实际中,利用该方法尝试将最大粒径为31.5 mm且具有较好抗离析稳定性的粗骨料用于自密实混凝土配制。实践证明,利用固定砂石总体积法配制较大粒径骨料自密实混凝土是可行的。

  6. Eight light flavors on large lattice volumes

    CERN Document Server

    Schaich, David

    2013-01-01

    I present first results from large-scale lattice investigations of SU(3) gauge theory with eight light flavors in the fundamental representation. Using leadership computing resources at Argonne, we are generating gauge configurations with lattice volumes up to $64^3\\times128$ at relatively strong coupling, in an attempt to access the chiral regime. We use nHYP-improved staggered fermions, carefully monitoring finite-volume effects and other systematics. Here I focus on analyses of the light hadron spectrum and chiral condensate, measured on lattice volumes up to $48^3\\times96$ with fermion masses as light as m=0.004 in lattice units. We find no clear indication of spontaneous chiral symmetry breaking in these observables. I discuss the implications of these initial results, and prospects for further physics projects employing these ensembles of gauge configurations.

  7. Simulating cosmic reionization: How large a volume is large enough?

    CERN Document Server

    Iliev, Ilian T; Ahn, Kyungjin; Shapiro, Paul R; Mao, Yi; Pen, Ue-Li

    2013-01-01

    We present the largest-volume (425 Mpc/h=607 Mpc on a side) full radiative transfer simulation of cosmic reionization to date. We show that there is significant additional power in density fluctuations at very large scales. We systematically investigate the effects this additional power has on the progress, duration and features of reionization, as well as on selected reionization observables. We find that comoving simulation volume of ~100 Mpc/h per side is sufficient for deriving a convergent mean reionization history, but that the reionization patchiness is significantly underestimated. We use jackknife splitting to quantify the convergence of reionization properties with simulation volume for both mean-density and variable-density sub-regions. We find that sub-volumes of ~100 Mpc/h per side or larger yield convergent reionization histories, except for the earliest times, but smaller volumes of ~50 Mpc/h or less are not well converged at any redshift. Reionization history milestones show significant scatte...

  8. Comments on large-N volume independence

    Energy Technology Data Exchange (ETDEWEB)

    Poppitz, Erich; /Toronto U.; Unsal, Mithat; /SLAC /Stanford U., Phys. Dept.

    2010-06-02

    We study aspects of the large-N volume independence on R{sup 3} X L{sup {Gamma}}, where L{sup {Gamma}} is a {Gamma}site lattice for Yang-Mills theory with adjoint Wilson-fermions. We find the critical number of lattice sites above which the center-symmetry analysis on L{sup {Gamma}} agrees with the one on the continuum S{sup 1}. For Wilson parameter set to one and {Gamma}{>=}2, the two analyses agree. One-loop radiative corrections to Wilson-line masses are finite, reminiscent of the UV-insensitivity of the Higgs mass in deconstruction/Little-Higgs theories. Even for theories with {Gamma}=1, volume independence in QCD(adj) may be guaranteed to work by tuning one low-energy effective field theory parameter. Within the parameter space of the theory, at most three operators of the 3d effective field theory exhibit one-loop UV-sensitivity. This opens the analytical prospect to study 4d non-perturbative physics by using lower dimensional field theories (d=3, in our example).

  9. Why Matter Occupies so Large a Volume?

    Science.gov (United States)

    E. B., Manoukian

    2013-12-01

    The paper represents a rigorous treatment of the underlying quantum theory, not just in words but providing the underlying technical details, as to why matter occupies so large a volume and its intimate connection with the Pauli exclusion principle, as more and more matter is put together, as well as of the contraction or shrinkage of “bosonic matter”, upon collapse, for which the Pauli exclusion is abolished. From the derived explicit bounds of integrals of powers of the particle number densities, explicit bounds on probabilities of the occurrences of the events just described are extracted. These probabilities lead one to infer the change of the “size” or extension of such matter, upon expansion or contraction, respectively, as their content is increased.

  10. The parallel volume at large distances

    DEFF Research Database (Denmark)

    Kampf, Jürgen

    In this paper we examine the asymptotic behavior of the parallel volume of planar non-convex bodies as the distance tends to infinity. We show that the difference between the parallel volume of the convex hull of a body and the parallel volume of the body itself tends to . This yields a new proof...... for the fact that a planar body can only have polynomial parallel volume, if it is convex. Extensions to Minkowski spaces and random sets are also discussed....

  11. The parallel volume at large distances

    DEFF Research Database (Denmark)

    Kampf, Jürgen

    In this paper we examine the asymptotic behavior of the parallel volume of planar non-convex bodies as the distance tends to infinity. We show that the difference between the parallel volume of the convex hull of a body and the parallel volume of the body itself tends to 0. This yields a new proof...... for the fact that a planar body can only have polynomial parallel volume, if it is convex. Extensions to Minkowski spaces and random sets are also discussed....

  12. Large volumes and spectroscopy of walking theories

    CERN Document Server

    Del Debbio, L; Patella, A; Pica, C; Rago, A

    2016-01-01

    A detailed investigation of finite size effects is performed for SU(2) gauge theory with two fermions in the adjoint representation, which previous lattice studies have shown to be inside the conformal window. The system is investigated with different spatial and temporal boundary conditions on lattices of various spatial and temporal extensions, for two values of the bare fermion mass representing a {\\em heavy} and {\\em light} fermion regime. Our study shows that the infinite volume limit of masses and decay constants in the mesonic sector is reached only when the mass of the pseudoscalar particle $M_\\mathrm{PS}$ and the spatial lattice size $L$ satisfy the relation $L M_\\mathrm{PS} \\ge 15$. This bound, which is at least a factor of three higher than what observed in QCD, is a likely consequence of the different spectral signatures of the two theories, with the scalar isosinglet ($0^{++}$ glueball) being the lightest particle in our model. In addition to stressing the importance of simulating large lattice s...

  13. The Combination of Tissue Dissection and External Volume Expansion Generates Large Volumes of Adipose Tissue.

    Science.gov (United States)

    He, Yunfan; Dong, Ziqing; Xie, Gan; Zhou, Tao; Lu, Feng

    2017-04-01

    Noninvasive external volume expansion device has been applied to stimulate nonsurgical breast enlargement in clinical settings. Although previous results demonstrate the capacity of external volume expansion to increase the number of adipocytes, this strategy alone is insufficient to reconstruct soft-tissue defects or increase breast mass. The authors combined a minimally invasive tissue dissection method with external volume expansion to generate large volumes of adipose tissue. In vitro, various densities of adipose-derived stem cells were prepared to evaluate relations between cell contacts and cell proliferation. In vivo, dorsal adipose tissue of rabbits was thoroughly dissected and the external volume expansion device was applied to maintain the released state. External volume expansion without tissue dissection served as the control. In the dissection group, the generated adipose tissue volume was much larger than that in the control group at all time points. A larger number of proliferating cells appeared in the dissection samples than in the control samples at the early stage after tissue dissection. At low cell density, adipose-derived stem cells displayed an increasing proliferation rate compared to high cell density. Protein expression analysis revealed that cell proliferation was mediated by a similar mechanism both in vivo and in vitro, involving the release of cell contact inhibition and Hippo/Yes-associated protein pathway activation. Adipose tissue dissection releases cell-to-cell contacts and induces adipose-derived stem cell proliferation. Preexpanded adipose-derived stem cells undergo adipogenesis under the adipogenic environment created by external volume expansion, leading to better adipose regeneration compared with the control.

  14. The Persistence of the Large Volumes in Black Holes

    CERN Document Server

    Ong, Yen Chin

    2015-01-01

    Classically, black holes admit maximal interior volumes that grow asymptotically linearly in time. We show that such volumes remain large when Hawking evaporation is taken into account. Even if a charged black hole approaches the extremal limit during this evolution, its volume continues to grow; although an exactly extremal black hole does not have a "large interior". We clarify this point and discuss the implications of our results to the information loss and firewall paradoxes.

  15. PREPARATION OF ULTRA-LOW VOLUME WEIGHT AUTOCLAVED AERATED CONCRETE

    Directory of Open Access Journals (Sweden)

    Ondrej Koutny

    2016-12-01

    Full Text Available Autoclaved aerated concrete is a modern construction material that gains its popularity especially due to its thermal insulation performance resulting from low volume weight and porous structure with sufficient mechanical strength. Nowadays, there are attempts to use this material for thermal insulation purposes and to replace current systems, which have many disadvantages, mainly concerning durability. The key for improvement of thermal insulation properties is therefore obtaining a material based on autoclaved aerated concrete with extremely low volume weight (below 200 kg/m ³ ensuring good thermal isolation properties, but with sufficient mechanical properties to allow easy manipulation. This material can be prepared by foaming very fine powder materials such as silica fume or very finely ground sand. This paper deals with the possibilities of preparation and summarizes the basic requirements for successful preparation of such a material.

  16. Large-volume results in SU(2) with adjoint fermions

    CERN Document Server

    Del Debbio, Luigi; Pica, Claudio; Patella, Agostino; Rago, Antonio; Roman, Sabin

    2014-01-01

    Taming finite-volume effects is a crucial ingredient in order to identify the existence of IR fixed points. We present the latest results from our numerical simulations of SU(2) gauge theory with 2 Dirac fermions in the adjoint representation on large volumes. We compare with previous results, and extrapolate to thermodynamic limit when possible.

  17. Large-volume results in SU(2) with adjoint fermions

    DEFF Research Database (Denmark)

    Del Debbio, Luigi; Lucini, Biagio; Pica, Claudio;

    2013-01-01

    Taming finite-volume effects is a crucial ingredient in order to identify the existence of IR fixed points. We present the latest results from our numerical simulations of SU(2) gauge theory with 2 Dirac fermions in the adjoint representation on large volumes. We compare with previous results, an...

  18. New reduced volume preparation regimen in colon capsule endoscopy

    Institute of Scientific and Technical Information of China (English)

    Yasuo Kakugawa; Kazuhide Higuchi; Shinji Tanaka; Hideki Ishikawa; Hisao Tajiri; Yutaka Saito; Shoichi Saito; Kenji Watanabe; Naoki Ohmiya; Mitsuyuki Murano; Shiro Oka; Tetsuo Arakawa; Hidemi Goto

    2012-01-01

    AIM:To evaluate the effectiveness of our proposed bowel preparation method for colon capsule endoscopy.METHODS:A pilot,multicenter,randomized controlled trial compared our proposed "reduced volume method" (group A) with the "conventional volume method" (group B) preparation regimens.Group A did not drink polyethylene glycol electrolyte lavage solution (PEGELS) the day before the capsule procedure,while group B drank 2 L.During the procedure day,groups A and B drank 2 L and 1 L of PEG-ELS,respectively,and swallowed the colon capsule (PillCam COLON(R) capsule).Two hours later the first booster of 100 g magnesium citrate mixed with 900 mL water was administered to both groups,and the second booster was administered six hours post capsule ingestion as long as the capsule had not been excreted by that time.Capsule videos were reviewed for grading of cleansing level.RESULTS:Sixty-four subjects were enrolled,with results from 60 analyzed.Groups A and B included 31 and 29 subjects,respectively.Twenty-nine (94%) subjects in group A and 25 (86%) subjects in group B had adequate bowel preparation (ns).Twenty-two (71%) of the 31 subjects in group A excreted the capsule within its battery life compared to 16 (55%) of the 29 subjects in group B (ns).Of the remaining 22 subjects whose capsules were not excreted within the battery life,all of the capsules reached the left side colon before they stopped functioning.A single adverse event was reported in one subject who had mild symptoms of nausea and vomiting one hour after starting to drink PEG-ELS,due to ingesting the PEG-ELS faster than recommended.CONCLUSION:Our proposed reduced volume bowel preparation method for colon capsule without PEG-ELS during the days before the procedure was as effective as the conventional volume method.

  19. On the Effective Description of Large Volume Compactifications

    CERN Document Server

    Gallego, Diego

    2011-01-01

    We study the reliability of the Two-Step moduli stabilization in the type-IIB Large Volume Scenarios with matter and gauge interactions. The general analysis is based on a family of N=1 Supergravity models with a factorizable invariant Kaehler function, where the decoupling between two sets of fields without a mass hierarchy is easily understood. For the Large Volume Scenario particular analyses are performed for explicit models, one of such developed for the first time here, finding that the simplified version, where the Dilaton and Complex structure moduli are regarded as frozen by a previous stabilization, is a reliable supersymmetric description whenever the neglected fields stand at their leading F-flatness conditions and be neutral. The terms missed by the simplified approach are either suppressed by powers of the Calabi-Yau volume, or are higher order operators in the matter fields, and then irrelevant for the moduli stabilization rocedure. Although the power of the volume suppressing such corrections ...

  20. Higgs, moduli problem, baryogenesis and large volume compactifications

    Energy Technology Data Exchange (ETDEWEB)

    Higaki, Tetsutaro [RIKEN Nishina Center, Saitama (Japan). Mathematical Physics Lab.; Kamada, Kohei [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Takahashi, Fuminobu [Tohoku Univ., Sendai (Japan). Dept. of Physics

    2012-07-15

    We consider the cosmological moduli problem in the context of high-scale supersymmetry breaking suggested by the recent discovery of the standard-model like Higgs boson. In order to solve the notorious moduli-induced gravitino problem, we focus on the LARGE volume scenario, in which the modulus decay into gravitinos can be kinematically forbidden. We then consider the Affleck-Dine mechanism with or without an enhanced coupling with the inflaton, taking account of possible Q-ball formation. We show that the baryon asymmetry of the present Universe can be generated by the Affleck-Dine mechanism in LARGE volume scenario, solving the moduli and gravitino problems.

  1. Soft Supersymmetry Breaking in Anisotropic LARGE Volume Compactifications

    CERN Document Server

    Angus, Stephen

    2014-01-01

    We study soft supersymmetry breaking terms for anisotropic LARGE volume compactifications, where the bulk volume is set by a fibration with one small four-cycle and one large two-cycle. We consider scenarios where D7s wrap either a blow-up cycle or the small fibre cycle. Chiral matter can arise either from modes parallel or perpendicular to the brane. We compute soft terms for this matter and find that for the case where the D7 brane wraps the fibre cycle the scalar masses can be parametrically different, allowing a possible splitting of third-generation soft terms.

  2. Alleviating the window problem in large volume renormalization schemes

    OpenAIRE

    Korcyl, Piotr

    2017-01-01

    We propose a strategy for large volume non-perturbative renormalization which alleviates the window problem by reducing cut-off effects. We perform a proof-of-concept study using position space renormalization scheme and the CLS $N_f=2+1$ ensembles generated at 5 different lattice spacings. We show that in the advocated strategy results for the renormalization constants are to a large extend independent of the specific lattice direction used to define the renormalization condition. Hence, ver...

  3. Limited streamer chambers for the Large Volume Detector

    NARCIS (Netherlands)

    Anzivino, G.; Bianco, S.; Casaccia, R.; Cindolo, F.; Daniello, L.; Felici, M. De; Enorini, M.; Fabbri, D.; Fabbri, F.L.; Giardoni, M.; Laakso, I.; Lindozzi, M.; Pallante, E.; Passamonti, L.; Russo, V.; Ventura, M.; Votano, L.; Zallo, A.; Bari, G.; Bruni, G.; Cara Romeo, G.; Contin, A.; Papa, C. Del; Iacobucci, G.; Maccarrone, G.; Mencarini, D.; Kania, R.; Sartorelli, G.; Qazi, N.I.; Sarwar, S.; Mao, C.S.; Wu, Y.R.

    1991-01-01

    The tracking system of the Large Volume Detector, an underground experiment to study muons and nutrino astronomy, will use ~15000 limited streamer chambers. We describe a comparison between the standard binary mixture (30% argon + 70% isobutane) and a low-hydrocarbon ternary mixture (2% argon + 10%

  4. Limited streamer chambers for the Large Volume Detector

    NARCIS (Netherlands)

    Anzivino, G.; Bianco, S.; Casaccia, R.; Cindolo, F.; Daniello, L.; Felici, M. De; Enorini, M.; Fabbri, D.; Fabbri, F.L.; Giardoni, M.; Laakso, I.; Lindozzi, M.; Pallante, E.; Passamonti, L.; Russo, V.; Ventura, M.; Votano, L.; Zallo, A.; Bari, G.; Bruni, G.; Cara Romeo, G.; Contin, A.; Papa, C. Del; Iacobucci, G.; Maccarrone, G.; Mencarini, D.; Kania, R.; Sartorelli, G.; Qazi, N.I.; Sarwar, S.; Mao, C.S.; Wu, Y.R.

    1991-01-01

    The tracking system of the Large Volume Detector, an underground experiment to study muons and nutrino astronomy, will use ~15000 limited streamer chambers. We describe a comparison between the standard binary mixture (30% argon + 70% isobutane) and a low-hydrocarbon ternary mixture (2% argon + 10%

  5. A bulk inflaton from large volume extra dimensions

    CERN Document Server

    Greene, Brian; Levin, Janna; Thurston, Dylan

    2010-01-01

    The universe may have extra spatial dimensions with large volume that we cannot perceive because the energy required to excite modes in the extra directions is too high. Many examples are known of such manifolds with a large volume and a large mass gap. These compactifications can help explain the weakness of four-dimensional gravity and, as we show here, they also have the capacity to produce reasonable potentials for an inflaton field. Modeling the inflaton as a bulk scalar field, it becomes very weakly coupled in four dimensions, and this enables us to build phenomenologically acceptable inflationary models with tunings at the few per mil level. We speculate on dark matter candidates and the possibility of braneless models in this setting.

  6. A bulk inflaton from large-volume extra dimensions

    Energy Technology Data Exchange (ETDEWEB)

    Greene, Brian, E-mail: greene@physics.columbia.ed [Institute for Strings, Cosmology and Astroparticle Physics (ISCAP), Columbia University, New York, NY 10027 (United States); Departments of Physics and Mathematics, Columbia University, New York, NY 10027 (United States); Kabat, Daniel, E-mail: daniel.kabat@lehman.cuny.ed [Department of Physics and Astronomy, Lehman College, CUNY, Bronx, NY 10468 (United States); Levin, Janna, E-mail: janna@astro.columbia.ed [Institute for Strings, Cosmology and Astroparticle Physics (ISCAP), Columbia University, New York, NY 10027 (United States); Department of Physics and Astronomy, Barnard College, Columbia University, New York, NY 10027 (United States); Thurston, Dylan, E-mail: dpt@cpw.math.columbia.ed [Department of Mathematics, Barnard College, Columbia University, New York, NY 10027 (United States)

    2011-01-03

    The universe may have extra spatial dimensions with large volume that we cannot perceive because the energy required to excite modes in the extra directions is too high. Many examples are known of manifolds with a large volume and a large mass gap. These compactifications can help explain the weakness of four-dimensional gravity and, as we show here, they also have the capacity to produce reasonable potentials for an inflaton field. Modeling the inflaton as a bulk scalar field, it becomes very weakly coupled in four dimensions and this enables us to build phenomenologically acceptable inflationary models with tunings at the few per mil level. We speculate on dark matter candidates and the possibility of braneless models in this setting.

  7. Large N Phase Transitions, Finite Volume, and Entanglement Entropy

    CERN Document Server

    Johnson, Clifford V

    2014-01-01

    Holographic studies of the entanglement entropy of field theories dual to charged and neutral black holes in asymptotically global AdS4 spacetimes are presented. The goal is to elucidate various properties of the quantity that are peculiar to working in finite volume, and to gain access to the behaviour of the entanglement entropy in the rich thermodynamic phase structure that is present at finite volume and large N. The entropy is followed through various first order phase transitions, and also a novel second order phase transition. Behaviour is found that contrasts interestingly with an earlier holographic study of a second order phase transition dual to an holographic superconductor.

  8. Accessibility and Analysis to NASA's New Large Volume Missions

    Science.gov (United States)

    Hausman, J.; Gangl, M.; McAuley, J.; Toaz, R., Jr.

    2016-12-01

    Each new satellite mission continues to measure larger volumes of data than the last. This is especially true with the new NASA satellite missions NISAR and SWOT, launching in 2020 and 2021, which will produce petabytes of data a year. A major concern is how will users be able to analyze such volumes? This presentation will show how cloud storage and analysis can help overcome and accommodate multiple users' needs. While users may only need gigabytes of data for their research, the data center will need to leverage the processing power of the cloud to perform search and subsetting capabilities over the large volume of data. There is also a vast array of user types that require different tools and services to access and analyze the data. Some users need global data to run climate models, while others require small, dynamic regions with lots of analysis and transformations. There will also be a need to generate data that have different inputs or correction algorithms that the project may not be able to provide as those will be very specialized for specific regions or evolve quicker than what the project can reprocess. By having the data and tools side by side, users will be able to access the data they require and analyze it all in one place. By placing data in the cloud, users can analyze the data there, shifting the current "download and analyze" paradigm to "log-in and analyze". The cloud will provide adequate processing power needed to analyze large volumes of data, subset small regions over large volumes of data, and regenerate/reformat data to the specificity each user requires.

  9. Calcium isolation from large-volume human urine samples for 41Ca analysis by accelerator mass spectrometry.

    Science.gov (United States)

    Miller, James J; Hui, Susanta K; Jackson, George S; Clark, Sara P; Einstein, Jane; Weaver, Connie M; Bhattacharyya, Maryka H

    2013-08-01

    Calcium oxalate precipitation is the first step in preparation of biological samples for (41)Ca analysis by accelerator mass spectrometry. A simplified protocol for large-volume human urine samples was characterized, with statistically significant increases in ion current and decreases in interference. This large-volume assay minimizes cost and effort and maximizes time after (41)Ca administration during which human samples, collected over a lifetime, provide (41)Ca:Ca ratios that are significantly above background.

  10. Calcium Isolation from Large-Volume Human Urine Samples for 41Ca Analysis by Accelerator Mass Spectrometry

    Science.gov (United States)

    Miller, James J; Hui, Susanta K; Jackson, George S; Clark, Sara P; Einstein, Jane; Weaver, Connie M; Bhattacharyya, Maryka H

    2013-01-01

    Calcium oxalate precipitation is the first step in preparation of biological samples for 41Ca analysis by accelerator mass spectrometry. A simplified protocol for large-volume human urine samples was characterized, with statistically significant increases in ion current and decreases in interference. This large-volume assay minimizes cost and effort and maximizes time after 41Ca administration during which human samples, collected over a lifetime, provide 41Ca:Ca ratios that are significantly above background. PMID:23672965

  11. Large Nc volume reduction and chiral random matrix theory

    CERN Document Server

    Lee, Jong-Wan; Yamada, Norikazu

    2013-01-01

    Motivated by recent progress on the understanding of the Eguchi-Kawai (EK) volume equivalence and growing interest in conformal window, we simultaneously use the large-Nc volume reduction and Chiral Random Matrix Theory (chRMT) to study the chiral symmetry breaking of four dimensional SU(Nc) gauge theory with adjoint fermions in the large Nc limit. Although some cares are required because the chRMT limit and 't Hooft limit are not compatible in general, we show that the breakdown of the chiral symmetry can be detected in large-Nc gauge theories. As a first step, we mainly focus on the quenched approximation to establish the methodology. We first confirm that heavy adjoint fermions, introduced as the center symmetry preserver, work as expected and thanks to them the volume reduction holds. Using massless overlap fermion as a probe, we then calculate the low-lying Dirac spectrum for fermion in the adjoint representation to compare to that of chRMT, and find that chiral symmetry is indeed broken in the quenched ...

  12. Large volume high-pressure cell for inelastic neutron scattering

    Energy Technology Data Exchange (ETDEWEB)

    Wang, W.; Kamenev, K. V. [Centre for Science at Extreme Conditions and School of Engineering, University of Edinburgh, Edinburgh EH9 3JZ (United Kingdom); Sokolov, D. A.; Huxley, A. D. [SUPA, Centre for Science at Extreme Conditions and School of Physics and Astronomy, University of Edinburgh, Edinburgh EH9 3JZ (United Kingdom)

    2011-07-15

    Inelastic neutron scattering measurements typically require two orders of magnitude longer data collection times and larger sample sizes than neutron diffraction studies. Inelastic neutron scattering measurements on pressurised samples are particularly challenging since standard high-pressure apparatus restricts sample volume, attenuates the incident and scattered beams, and contributes background scattering. Here, we present the design of a large volume two-layered piston-cylinder pressure cell with optimised transmission for inelastic neutron scattering experiments. The design and the materials selected for the construction of the cell enable its safe use to a pressure of 1.8 GPa with a sample volume in excess of 400 mm{sup 3}. The design of the piston seal eliminates the need for a sample container, thus providing a larger sample volume and reduced absorption. The integrated electrical plug with a manganin pressure gauge offers an accurate measurement of pressure over the whole range of operational temperatures. The performance of the cell is demonstrated by an inelastic neutron scattering study of UGe{sub 2}.

  13. Large volume high-pressure cell for inelastic neutron scattering

    Science.gov (United States)

    Wang, W.; Sokolov, D. A.; Huxley, A. D.; Kamenev, K. V.

    2011-07-01

    Inelastic neutron scattering measurements typically require two orders of magnitude longer data collection times and larger sample sizes than neutron diffraction studies. Inelastic neutron scattering measurements on pressurised samples are particularly challenging since standard high-pressure apparatus restricts sample volume, attenuates the incident and scattered beams, and contributes background scattering. Here, we present the design of a large volume two-layered piston-cylinder pressure cell with optimised transmission for inelastic neutron scattering experiments. The design and the materials selected for the construction of the cell enable its safe use to a pressure of 1.8 GPa with a sample volume in excess of 400 mm3. The design of the piston seal eliminates the need for a sample container, thus providing a larger sample volume and reduced absorption. The integrated electrical plug with a manganin pressure gauge offers an accurate measurement of pressure over the whole range of operational temperatures. The performance of the cell is demonstrated by an inelastic neutron scattering study of UGe2.

  14. Low-volume plus ascorbic acid vs high-volume plus simethicone bowel preparation before colonoscopy

    Institute of Scientific and Technical Information of China (English)

    Stefano Pontone; Rita Angelini; Monica Standoli; Gregorio Patrizi; Franco Culasso; Paolo Pontone; Adriano Redler

    2011-01-01

    AIM: To investigate the effectiveness of low-volume plus ascorbic acid [polyethylene glycol plus ascorbic acid (PEG + Asc)] and high-volume plus simethicone [polyethylene glycol plus simethicone (PEG + Sim)] bowel preparations.METHODS: A total of one hundred and forty-four outpatients (76 males), aged from 20 to 84 years (me dian age 59.5 years), who attended our Department, were divided into two groups, age and sex matched, and underwent colonoscopy. Two questionnaires, one for patients reporting acceptability and the other for endoscopists evaluating bowel cleansing effectiveness according to validated scales, were completed. Indica tions, timing of examination and endoscopical findings were recorded. Biopsy forceps were used as a measur ing tool in order to determine polyp endoscopic sizeestimation. Difficulty in completing the preparation was rated in a 5-point Likert scale (1 = easy to 5 = un able). Adverse experiences (fullness, cramps, nausea, vomiting, abdominal pain, headache and insomnia), number of evacuations and types of activities per formed during preparation (walking or resting in bed) were also investigated.RESULTS: Seventy-two patients were selected for each group. The two groups were age and sex matched as well as being comparable in terms of medical history and drug therapies taken. Fourteen patients dropped out from the trial because they did not complete the preparation procedure. Ratings of global bowel cleans ing examinations were considered to be adequate in 91% of PEG + Asc and 88% of PEG + Sim patients. Residual Stool Score indicated similar levels of amount and consistency of residual stool; there was a signifi cant difference in the percentage of bowel wall visuali zation in favour of PEG + Sim patients. In the PEG + Sim group, 12 adenomas < 10 mm diameter (5/left co lon + 7/right colon) vs 9 (8/left colon + 1/right colon) in the PEG + Asc group were diagnosed. Visualization of small lesions seems to be one of the primary advan tages of

  15. Light propagation in a large volume liquid scintillator

    CERN Document Server

    Alimonti, G; Balata, M; Bellini, G; Benziger, J; Bonetti, S; Caccianiga, B; Cadonati, L; Calaprice, F P; Cecchet, G; Chen, M; Darnton, N; De Bari, A; Deutsch, M; Elisei, F; Feilitzsch, F V; Galbiati, C; Gatti, F; Giammarchi, M G; Giugni, D; Goldbrunner, T; Golubchikov, A; Goretti, A; Hagner, T; Hartmann, F X; Hentig, R V; Heusser, G; Ianni, A; Johnson, M; Laubenstein, M; Lombardi, P; Magni, S; Malvezzi, S; Maneira, J; Manno, I; Manuzio, G; Masetti, F; Mazzucato, U; Meroni, E; Neff, M; Oberauer, L; Perotti, A; Raghavan, R S; Ranucci, G; Resconi, E; Salvo, C; Scardaoni, R; Schönert, S; Smirnov, O; Tartaglia, R; Testera, G; Vogelaar, R B; Vitale, S; Zaimidoroga, O A

    2000-01-01

    The fluorescence light propagation in a large volume detector based on organic liquid scintillators is discussed. In particular, the effects of the fluor radiative transport and solvent Rayleigh scattering are emphasized. These processes have been modelled by a ray-tracing Monte Carlo method and have been experimentally investigated in the Borexino prototype which was a 4.3 ton, 4 pi sensitive detector. The comparison between the model prediction and the experimental data shows a satisfactory agreement indicating that the main aspects of these processes are well understood. Some features of the experimental time response of the detector are still under study.

  16. Naturally light hidden photons in LARGE volume string compactifications

    Energy Technology Data Exchange (ETDEWEB)

    Goodsell, M. [LPTHE, Univ. Pierre et Marie Curie, Paris (France); Jaeckel, J. [Inst. for Particle Physics Phenomenology, Univ. Durham (United Kingdom); Redondo, J.; Ringwald, A. [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany)

    2009-09-15

    Extra ''hidden'' U(1) gauge factors are a generic feature of string theory that is of particular phenomenological interest. They can kinetically mix with the Standard Model photon and are thereby accessible to a wide variety of astrophysical and cosmological observations and laboratory experiments. In this paper we investigate the masses and the kinetic mixing of hidden U(1)s in LARGE volume compactifications of string theory. We find that in these scenarios the hidden photons can be naturally light and that their kinetic mixing with the ordinary electromagnetic photon can be of a size interesting for near future experiments and observations. (orig.)

  17. Astrophysical and Cosmological Implications of Large Volume String Compactifications

    CERN Document Server

    Conlon, Joseph P

    2007-01-01

    We study the spectrum, couplings and cosmological and astrophysical implications of the moduli fields for the class of Calabi-Yau IIB string compactifications for which moduli stabilisation leads to an exponentially large volume V ~ 10^{15} l_s^6 and an intermediate string scale m_s ~ 10^{11}GeV, with TeV-scale observable supersymmetry breaking. All K\\"ahler moduli except for the overall volume are heavier than the susy breaking scale, with m ~ ln(M_P/m_{3/2}) m_{3/2} ~ (\\ln(M_P/m_{3/2}))^2 m_{susy} ~ 500 TeV and, contrary to standard expectations, have matter couplings suppressed only by the string scale rather than the Planck scale. These decay to matter early in the history of the universe, with a reheat temperature T ~ 10^7 GeV, and are free from the cosmological moduli problem (CMP). The heavy moduli have a branching ratio to gravitino pairs of 10^{-30} and do not suffer from the gravitino overproduction problem. The overall volume modulus is a distinctive feature of these models and is an M_{planck}-cou...

  18. Large pore volume mesoporous aluminum oxide synthesized via nano-assembly

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    A new nano-assembly approach has been proposed for the preparation of macropore volume mesoporous aluminum oxide supports. Secondary nano-assembly and a frame structure mechanism for large pore volume mesoporous supports have been proposed. In a primary nano-assembly supersoluble micelle,aluminum hydroxide nanoparticles were precipitated in situ in surfactants with a volume balance (VB) less than 1,followed by secondary nano-assembly in linear and cylindrical shapes. The secondary nano-assembly of cylindrical aluminum hydroxides was calcined to form nano cylindrical aluminum oxides. For the formation of macropore volume mesoporous supports,we utilized a frame structure mechanism of mesoporous support,in which the exterior surface of the carrier may not be continuous. This macropore volume support has been used for the hydrotreatment of a residual oil catalyst,which possesses the following physical characteristics:pore volume 1.8―2.7 mL·g-1,specific surface area 180―429 m2·g-1,average pore diameter 17―57 nm,average pore diameter more than 10 nm (81%―94%),porosity 87%―93%,and crush strength 7.7―25 N·mm-1.

  19. Preparation of cluster state in large detuned cavity

    Institute of Scientific and Technical Information of China (English)

    Zou Chang-Lin; Gao Guo-Jun; Lu Yan; Li Da-Chuang; Yang Ming; Cao Zhuo-Liang

    2008-01-01

    An experimentally realizable physical scheme for preparing multiqubit cluster states from a large detuned atomcavity interaction is proposed. The scheme is free of any type of measurement and insensitive to the cavity decay, and the cavity field is only virtually excited so that there is no information exchanging between atom and cavity. The time required for the gate operations is very short, which is important for decoherence. We also discuss the experimental feasibility of our scheme.

  20. A meta-analysis of randomized controlled trials of low-volume polyethylene glycol plus ascorbic acid versus standard-volume polyethylene glycol solution as bowel preparations for colonoscopy.

    Directory of Open Access Journals (Sweden)

    Qingsong Xie

    Full Text Available BACKGROUND: Standard-volume polyethylene glycol (PEG gut lavage solutions are safe and effective, but they require the consumption of large volumes of fluid. A new lower-volume solution of PEG plus ascorbic acid has been used recently as a preparation for colonoscopy. AIM: A meta-analysis was performed to compare the performance of low-volume PEG plus ascorbic acid with standard-volume PEG as bowel preparation for colonoscopy. STUDY: Electronic and manual searches were performed to identify randomized controlled trials (RCTs that compared the performance of low-volume PEG plus ascorbic acid with standard-volume PEG as bowel preparation for colonoscopy. After a methodological quality assessment and data extraction, the pooled estimates of bowel preparation efficacy during bowel cleansing, compliance with preparation, willingness to repeat the same preparation, and the side effects were calculated. We calculated pooled estimates of odds ratios (OR by fixed- and/or random-effects models. We also assessed heterogeneity among studies and the publication bias. RESULTS: Eleven RCTs were identified for analysis. The pooled OR for preparation efficacy during bowel cleansing and for compliance with preparation for low-volume PEG plus ascorbic acid were 1.08 (95% CI = 0.98-1.28, P = 0.34 and 2.23 (95% CI = 1.67-2.98, P<0.00001, respectively, compared with those for standard-volume PEG. The side effects of vomiting and nausea for low-volume PEG plus ascorbic acid were reduced relative to standard-volume PEG. There was no significant publication bias, according to a funnel plot. CONCLUSIONS: Low-volume PEG plus ascorbic acid gut lavage achieved non-inferior efficacy for bowel cleansing, is more acceptable to patients, and has fewer side effects than standard-volume PEG as a bowel preparation method for colonoscopy.

  1. SUSY’s Ladder: reframing sequestering at Large Volume

    Energy Technology Data Exchange (ETDEWEB)

    Reece, Matthew [Department of Physics, Harvard University,Cambridge, MA 02138 (United States); Xue, Wei [Center for Theoretical Physics, Massachusetts Institute of Technology,Cambridge, MA 02139 (United States)

    2016-04-07

    Theories with approximate no-scale structure, such as the Large Volume Scenario, have a distinctive hierarchy of multiple mass scales in between TeV gaugino masses and the Planck scale, which we call SUSY’s Ladder. This is a particular realization of Split Supersymmetry in which the same small parameter suppresses gaugino masses relative to scalar soft masses, scalar soft masses relative to the gravitino mass, and the UV cutoff or string scale relative to the Planck scale. This scenario has many phenomenologically interesting properties, and can avoid dangers including the gravitino problem, flavor problems, and the moduli-induced LSP problem that plague other supersymmetric theories. We study SUSY’s Ladder using a superspace formalism that makes the mysterious cancelations in previous computations manifest. This opens the possibility of a consistent effective field theory understanding of the phenomenology of these scenarios, based on power-counting in the small ratio of string to Planck scales. We also show that four-dimensional theories with approximate no-scale structure enforced by a single volume modulus arise only from two special higher-dimensional theories: five-dimensional supergravity and ten-dimensional type IIB supergravity. This gives a phenomenological argument in favor of ten dimensional ultraviolet physics which is different from standard arguments based on the consistency of superstring theory.

  2. Multisystem organ failure after large volume injection of castor oil.

    Science.gov (United States)

    Smith, Silas W; Graber, Nathan M; Johnson, Rudolph C; Barr, John R; Hoffman, Robert S; Nelson, Lewis S

    2009-01-01

    We report a case of multisystem organ failure after large volume subcutaneous injection of castor oil for cosmetic enhancement. An unlicensed practitioner injected 500 mL of castor oil bilaterally to the hips and buttocks of a 28-year-old male to female transsexual. Immediate local pain and erythema were followed by abdominal and chest pain, emesis, headache, hematuria, jaundice, and tinnitus. She presented to an emergency department 12 hours postinjection. Persistently hemolyzed blood samples complicated preliminary laboratory analysis. She rapidly deteriorated despite treatment and developed fever, tachycardia, hemolysis, thrombocytopenia, hepatitis, respiratory distress, and anuric renal failure. An infectious diseases evaluation was negative. After intensive supportive care, including mechanical ventilation and hemodialysis, she was discharged 11 days later, requiring dialysis for an additional 1.5 months. Castor oil absorption was inferred from recovery of the Ricinus communis biomarker, ricinine, in the patient's urine (41 ng/mL). Clinicians should anticipate multiple complications after unapproved methods of cosmetic enhancement.

  3. Striped Bass, morone saxatilis, egg incubation in large volume jars

    Science.gov (United States)

    Harper, C.J.; Wrege, B.M.; Jeffery, Isely J.

    2010-01-01

    The standard McDonald jar was compared with a large volume jar for striped bass, Morone saxatilis, egg incubation. The McDonald jar measured 16 cm in diameter by 45 cm in height and had a volume of 6 L. The experimental jar measured 0.4 m in diameter by 1.3 m in height and had a volume of 200 L. The hypothesis is that there is no difference in percent survival of fry hatched in experimental jars compared with McDonald jars. Striped bass brood fish were collected from the Coosa River and spawned using the dry spawn method of fertilization. Four McDonald jars were stocked with approximately 150 g of eggs each. Post-hatch survival was estimated at 48, 96, and 144 h. Stocking rates resulted in an average egg loading rate (??1 SE) in McDonald jars of 21.9 ?? 0.03 eggs/mL and in experimental jars of 10.9 ?? 0.57 eggs/mL. The major finding of this study was that average fry survival was 37.3 ?? 4.49% for McDonald jars and 34.2 ?? 3.80% for experimental jars. Although survival in experimental jars was slightly less than in McDonald jars, the effect of container volume on survival to 48 h (F = 6.57; df = 1,5; P > 0.05), 96 h (F = 0.02; df = 1, 4; P > 0.89), and 144 h (F = 3.50; df = 1, 4; P > 0.13) was not statistically significant. Mean survival between replicates ranged from 14.7 to 60.1% in McDonald jars and from 10.1 to 54.4% in experimental jars. No effect of initial stocking rate on survival (t = 0.06; df = 10; P > 0.95) was detected. Experimental jars allowed for incubation of a greater number of eggs in less than half the floor space of McDonald jars. As hatchery production is often limited by space or water supply, experimental jars offer an alternative to extending spawning activities, thereby reducing labor and operations cost. As survival was similar to McDonald jars, the experimental jar is suitable for striped bass egg incubation. ?? Copyright by the World Aquaculture Society 2010.

  4. Volume visualization of multiple alignment of large genomicDNA

    Energy Technology Data Exchange (ETDEWEB)

    Shah, Nameeta; Dillard, Scott E.; Weber, Gunther H.; Hamann, Bernd

    2005-07-25

    Genomes of hundreds of species have been sequenced to date, and many more are being sequenced. As more and more sequence data sets become available, and as the challenge of comparing these massive ''billion basepair DNA sequences'' becomes substantial, so does the need for more powerful tools supporting the exploration of these data sets. Similarity score data used to compare aligned DNA sequences is inherently one-dimensional. One-dimensional (1D) representations of these data sets do not effectively utilize screen real estate. As a result, tools using 1D representations are incapable of providing informatory overview for extremely large data sets. We present a technique to arrange 1D data in 3D space to allow us to apply state-of-the-art interactive volume visualization techniques for data exploration. We demonstrate our technique using multi-millions-basepair-long aligned DNA sequence data and compare it with traditional 1D line plots. The results show that our technique is superior in providing an overview of entire data sets. Our technique, coupled with 1D line plots, results in effective multi-resolution visualization of very large aligned sequence data sets.

  5. Characterization of segmented large volume, high purity germanium detectors

    Energy Technology Data Exchange (ETDEWEB)

    Bruyneel, B. [Koeln Univ. (Germany). Inst. fuer Kernphysik

    2006-07-01

    {gamma}-ray tracking in future HPGe arrays like AGATA will rely on pulse shape analysis (PSA) of multiple {gamma}-interactions. For this purpose, a simple and fast procedure was developed which enabled the first full characterization of a segmented large volume HPGe detector. An analytical model for the hole mobility in a Ge crystal lattice was developed to describe the hole drift anisotropy with experimental velocity values along the crystal axis as parameters. The new model is based on the drifted Maxwellian hole distribution in Ge. It is verified by reproducing successfully experimental longitudinal hole anisotropy data. A comparison between electron and hole mobility shows large differences for the longitudinal and tangential velocity anisotropy as a function of the electrical field orientation. Measurements on a 12 fold segmented, n-type, large volume, irregular shaped HPGe detector were performed in order to determine the parameters of anisotropic mobility for electrons and holes as charge carriers created by {gamma}-ray interactions. To characterize the electron mobility the complete outer detector surface was scanned in small steps employing photopeak interactions at 60 keV. A precise measurement of the hole drift anisotropy was performed with 356 keV rays. The drift velocity anisotropy and crystal geometry cause considerable rise time differences in pulse shapes depending on the position of the spatial charge carrier creation. Pulse shapes of direct and transient signals are reproduced by weighting potential calculations with high precision. The measured angular dependence of rise times is caused by the anisotropic mobility, crystal geometry, changing field strength and space charge effects. Preamplified signals were processed employing digital spectroscopy electronics. Response functions, crosstalk contributions and averaging procedures were taken into account implying novel methods due to the segmentation of the Ge-crystal and the digital electronics

  6. Astrophysical and cosmological implications of large volume string compactifications

    Science.gov (United States)

    Conlon, Joseph P.; Quevedo, Fernando

    2007-08-01

    We study the spectrum, couplings and cosmological and astrophysical implications of the moduli fields for the class of Calabi Yau IIB string compactifications for which moduli stabilisation leads to an exponentially large volume \\mathcal {V} \\sim 10^{15} l_{\\mathrm {s}}^6 and an intermediate string scale ms~1011 GeV, with TeV-scale observable supersymmetry breaking. All Kähler moduli except for the overall volume are heavier than the susy (supersymmetry) breaking scale, with m~ln(MP/m3/2)m3/2~(ln(MP/m3/2))2msusy~500 TeV and, contrary to standard expectations, have matter couplings suppressed only by the string scale rather than the Planck scale. These decay to matter early in the history of the universe, with a reheat temperature T~107 GeV, and are free from the cosmological moduli problem (CMP). The heavy moduli have a branching ratio to gravitino pairs of 10-30 and do not suffer from the gravitino overproduction problem. The overall volume modulus is a distinctive feature of these models and is an Mplanck-coupled scalar of mass m~1 MeV and subject to the CMP. A period of thermal inflation may help relax this problem. This field has a lifetime τ~1024 s and can contribute to dark matter. It may be detected through its decays to γγ or e+e-. If accessible the e+e- decay mode dominates, with \\mathrm {Br}(\\chi \\to \\gamma \\gamma) suppressed by a factor (ln(MP/m3/2))2. We consider the potential for detection of this field through different astrophysical sources: the Milky Way halo, the diffuse cosmic background and nearby galaxy clusters and find that the observed gamma ray background constrains \\Omega_{\\chi } \\lesssim 10^{-4} . The decays of this field may generate the 511 keV emission line from the galactic centre observed by INTEGRAL/SPI.

  7. Preliminary Results from the Large Volume Torsion (LVT) Deformation Apparatus

    Science.gov (United States)

    Cross, A. J.; Couvy, H.; Skemer, P. A.

    2015-12-01

    We present preliminary results from the Large Volume Torsion (LVT) apparatus, currently under development in the rock deformation lab at Washington University in St. Louis. The LVT is designed to deform disk-shaped samples (~4 mm in diameter) in torsion at lower-crustal to upper-mantle pressure and temperature conditions. Conceptually, the LVT complements and is similar in design to the Rotational Drickamer Apparatus (RDA) (Yamakazi & Karato, 2001), which deforms smaller samples at higher pressures. As part of our recent development efforts, benchmarking experiments were performed on Carrara marble. Samples were deformed in torsion at a strain rate of ~5 x 10-5 s-1 to moderate shear strains (γ ≤ 10) under lower crustal conditions (800°C, 2 GPa confining pressure). Microstructural observations from optical microscopy and electron backscatter diffraction (EBSD) show evidence for relict grain elongation and alignment; an increase in calcite twin density; and grain size reduction concurrent with recrystallized grain nucleation. Microstructural observations are comparable to data obtained from previous studies at lower pressure (e.g. Barnhoorn et al., 2004), confirming that the LVT provides reliable microstructural results.

  8. Dark Radiation predictions from general Large Volume Scenarios

    CERN Document Server

    Hebecker, Arthur; Rompineve, Fabrizio; Witkowski, Lukas T

    2014-01-01

    Recent observations constrain the amount of Dark Radiation ($\\Delta N_{\\rm eff}$) and may even hint towards a non-zero value of $\\Delta N_{\\rm eff}$. It is by now well-known that this puts stringent constraints on the sequestered Large Volume Scenario (LVS), i.e. on LVS realisations with the Standard Model at a singularity. We go beyond this setting by considering LVS models where SM fields are realised on 7-branes in the geometric regime. As we argue, this naturally goes together with high-scale supersymmetry. The abundance of Dark Radiation is determined by the competition between the decay of the lightest modulus to axions, to the SM Higgs and to gauge fields. The latter decay channel avoids the most stringent constraints of the sequestered setting. Nevertheless, a rather robust prediction for a substantial amount of Dark Radiation can be made. This applies both to cases where the SM 4-cycles are stabilised by D-terms and are small "by accident" as well as to fibred models with the small cycles stabilised ...

  9. Testing large volume water treatment and crude oil ...

    Science.gov (United States)

    Report EPA’s Homeland Security Research Program (HSRP) partnered with the Idaho National Laboratory (INL) to build the Water Security Test Bed (WSTB) at the INL test site outside of Idaho Falls, Idaho. The WSTB was built using an 8-inch (20 cm) diameter cement-mortar lined drinking water pipe that was previously taken out of service. The pipe was exhumed from the INL grounds and oriented in the shape of a small drinking water distribution system. Effluent from the pipe is captured in a lagoon. The WSTB can support drinking water distribution system research on a variety of drinking water treatment topics including biofilms, water quality, sensors, and homeland security related contaminants. Because the WSTB is constructed of real drinking water distribution system pipes, research can be conducted under conditions similar to those in a real drinking water system. In 2014, WSTB pipe was experimentally contaminated with Bacillus globigii spores, a non-pathogenic surrogate for the pathogenic B. anthracis, and then decontaminated using chlorine dioxide. In 2015, the WSTB was used to perform the following experiments: • Four mobile disinfection technologies were tested for their ability to disinfect large volumes of biologically contaminated “dirty” water from the WSTB. B. globigii spores acted as the biological contaminant. The four technologies evaluated included: (1) Hayward Saline C™ 6.0 Chlorination System, (2) Advanced Oxidation Process (A

  10. Capillary gas chromatographic analysis of nerve agents using large volume injections. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Deinum, T.; Nieuwenhuy, C.

    1994-11-01

    The procedure developed at TNO-Prins Maurits Laboratory (TNO-PML) for the verification of intact organophosphorus chemical warfare agents in water samples was improved. The last step in this procedure, the laborious and non-reproducible transfer of an ethyl acetate extract onto a Tenax-adsorption tube followed by thermal desorption of the Tenax-tube, was replaced by large volume injection of the extract onto a capillary gas chromatographic system. The parameters controlling the injection of a large volume of an extract (200 ul) were investigated and optimized. As ethyl acetate caused severe problems, potential new solvents were evaluated. With the improved procedure, the nerve agents sarin, tabun, soman, diisopropyl fluorophosphate (DFP) and VX could be determined in freshly prepared water samples at pg/ml (ppt) levels. The fate of the nerve agents under study in water at two pH`s (4.8 and 6) was investigated. For VX, the pH should be adjusted before extraction. Moreover, it is worthwhile to acidify water samples to diminish hydrolysis.

  11. A simple method for the production of large volume 3D macroporous hydrogels for advanced biotechnological, medical and environmental applications

    Science.gov (United States)

    Savina, Irina N.; Ingavle, Ganesh C.; Cundy, Andrew B.; Mikhalovsky, Sergey V.

    2016-02-01

    The development of bulk, three-dimensional (3D), macroporous polymers with high permeability, large surface area and large volume is highly desirable for a range of applications in the biomedical, biotechnological and environmental areas. The experimental techniques currently used are limited to the production of small size and volume cryogel material. In this work we propose a novel, versatile, simple and reproducible method for the synthesis of large volume porous polymer hydrogels by cryogelation. By controlling the freezing process of the reagent/polymer solution, large-scale 3D macroporous gels with wide interconnected pores (up to 200 μm in diameter) and large accessible surface area have been synthesized. For the first time, macroporous gels (of up to 400 ml bulk volume) with controlled porous structure were manufactured, with potential for scale up to much larger gel dimensions. This method can be used for production of novel 3D multi-component macroporous composite materials with a uniform distribution of embedded particles. The proposed method provides better control of freezing conditions and thus overcomes existing drawbacks limiting production of large gel-based devices and matrices. The proposed method could serve as a new design concept for functional 3D macroporous gels and composites preparation for biomedical, biotechnological and environmental applications.

  12. DIAGNOdent measurements and correlation with the depth and volume of minimally invasive cavity preparations.

    Science.gov (United States)

    Hamilton, James C; Gregory, William A; Valentine, John B

    2006-01-01

    In this clinical study, DIAGNOdent (KaVo) was used to assess previously diagnosed carious lesions in the pits and fissures of first and second molars. The measurements from this device were correlated with the depth and volume of the cavity preparations that resulted from minimal intervention to remove occlusal carious lesions. Twenty-five patients, 18 years of age and older, who were previously scheduled for an occlusal restoration due to caries, were recruited and enrolled in this clinical study. These patients had 48 qualifying teeth without previous restorations, sealants or other carious lesions. The occlusal surface of each study tooth was cleaned utilizing ProphyFlex2 (KaVo). Two dentists separately traced the pit and fissure system of each tooth using DIAGNOdent for two 15-second periods each. The peak reading of each of the four measurements was recorded. An impression of the occlusal surface of each tooth was recorded with a polyvinyl siloxane bite registration material. The carious lesions were removed with an air abrasion unit employing a 0.015-inch nozzle opening utilizing minimal operative intervention. A low viscosity polyvinyl siloxane was used to take an impression of the cavity preparation impression, using the bite registration impression to form the occlusal surface of the preparation impression. The preparation impression volume was calculated from its weight, using the known density of the impression material. The greatest depth of the preparation was measured. The Pearson correlation coefficient was used to investigate any relationship between depth or volume of the preparation impression and the DIAGNOdent measurements. The correlation for preparation volume and maximum DIAGNOdent measurement was 0.191 (p = 0.189). Other logical subsets of cases also did not result in any statistically significant correlations between the DIAGNOdent readings and the depth or volume of the final cavity preparations.

  13. RADON DIAGNOSTIC MEASUREMENT GUIDANCE FOR LARGE BUILDINGS - VOLUME 2. APPENDICES

    Science.gov (United States)

    The report discusses the development of radon diagnostic procedures and mitigation strategies applicable to a variety of large non-residential buildings commonly found in Florida. The investigations document and evaluate the nature of radon occurrence and entry mechanisms for rad...

  14. RADON DIAGNOSTIC MEASUREMENT GUIDANCE FOR LARGE BUILDINGS - VOLUME 2. APPENDICES

    Science.gov (United States)

    The report discusses the development of radon diagnostic procedures and mitigation strategies applicable to a variety of large non-residential buildings commonly found in Florida. The investigations document and evaluate the nature of radon occurrence and entry mechanisms for rad...

  15. Special Properties of Coherence Scanning Interferometers for large Measurement Volumes

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, W, E-mail: W.bauer@polytec.de [Polytec GmbH, Polytec Platz 1-7, 76337 Waldbronn (Germany)

    2011-08-19

    In contrast to many other optical methods the uncertainty of Coherence Scanning Interferometer (CSI) in vertical direction is independent from the field of view. Therefore CSIs are ideal instruments for measuring 3D-profiles of larger areas (36x28mm{sup 2}, e.g.) with high precision. This is of advantage for the determination of form parameters like flatness, parallelism and steps heights within a short time. In addition, using a telecentric beam path allows measurements of deep lying surfaces (<70mm) and the determination of form parameters with large step-heights. The lateral and spatial resolution, however, are reduced. In this presentation different metrological characteristics together with their potential errors are analyzed for large-scale measuring CSIs. Therefore these instruments are ideal tools in quality control for good/bad selections, e.g. The consequences for the practical use in industry and for standardization are discussed by examples of workpieces of automotive suppliers or from the steel industry.

  16. Tenth annual coal preparation, utilization, and environmental control contractors conference: Proceedings. Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    1994-08-01

    Volume I contains papers presented at the following sessions: high efficiency preparation; advanced physical coal cleaning; superclean emission systems; air toxics and mercury measurement and control workshop; and mercury measurement and control workshop. Selected papers have been processed for inclusion in the Energy Science and Technology Database.

  17. Large-volume protein crystal growth for neutron macromolecular crystallography.

    Science.gov (United States)

    Ng, Joseph D; Baird, James K; Coates, Leighton; Garcia-Ruiz, Juan M; Hodge, Teresa A; Huang, Sijay

    2015-04-01

    Neutron macromolecular crystallography (NMC) is the prevailing method for the accurate determination of the positions of H atoms in macromolecules. As neutron sources are becoming more available to general users, finding means to optimize the growth of protein crystals to sizes suitable for NMC is extremely important. Historically, much has been learned about growing crystals for X-ray diffraction. However, owing to new-generation synchrotron X-ray facilities and sensitive detectors, protein crystal sizes as small as in the nano-range have become adequate for structure determination, lessening the necessity to grow large crystals. Here, some of the approaches, techniques and considerations for the growth of crystals to significant dimensions that are now relevant to NMC are revisited. These include experimental strategies utilizing solubility diagrams, ripening effects, classical crystallization techniques, microgravity and theoretical considerations.

  18. Environmentally Safe, Large Volume Utilization Applications for Gasification Byproducts

    Energy Technology Data Exchange (ETDEWEB)

    J.G. Groppo; R. Rathbone

    2008-06-30

    Samples of gasification by-products produced at Polk Station and Eastman Chemical were obtained and characterized. Bulk samples were prepared for utilization studies by screening at the appropriate size fractions where char and vitreous frit distinctly partitioned. Vitreous frit was concentrated in the +20 mesh fraction while char predominated in the -20+100 mesh fraction. The vitreous frit component derived from each gasifier slag source was evaluated for use as a pozzolan and as aggregate. Pozzolan testing required grinding the frit to very fine sizes which required a minimum of 60 kwhr/ton. Grinding studies showed that the energy requirement for grinding the Polk slag were slightly higher than for the Eastman slag. Fine-ground slag from both gasifiers showed pozzoalnic activity in mortar cube testing and met the ASTM C618 strength requirements after only 3 days. Pozzolanic activity was further examined using British Standard 196-5, and results suggest that the Polk slag was more reactive than the Eastman slag. Neither aggregate showed significant potential for undergoing alkali-silica reactions when used as concrete aggregate with ASTM test method 1260. Testing was conducted to evaluate the use of the frit product as a component of cement kiln feed. The clinker produced was comprised primarily of the desirable components Ca{sub 3}SiO{sub 5} and Ca{sub 2}SiO{sub 4} after raw ingredient proportions were adjusted to reduce the amount of free lime present in the clinker. A mobile processing plant was designed to produce 100 tons of carbon from the Eastman slag to conduct evaluations for use as recycle fuel. The processing plant was mounted on a trailer and hauled to the site for use. Two product stockpiles were generated; the frit stockpile contained 5% LOI while the carbon stockpile contained 62% LOI. The products were used to conduct recycle fuel tests. A processing plant was designed to separate the slag produced at Eastman into 3 usable products. The coarse frit

  19. Radiation from Large Gas Volumes and Heat Exchange in Steam Boiler Furnaces

    Energy Technology Data Exchange (ETDEWEB)

    Makarov, A. N., E-mail: tgtu-kafedra-ese@mail.ru [Tver State Technical University (Russian Federation)

    2015-09-15

    Radiation from large cylindrical gas volumes is studied as a means of simulating the flare in steam boiler furnaces. Calculations of heat exchange in a furnace by the zonal method and by simulation of the flare with cylindrical gas volumes are described. The latter method is more accurate and yields more reliable information on heat transfer processes taking place in furnaces.

  20. [INFLUENCE OF LIPOSUCTION OF LARGE VOLUME ON SYSTEMIC AND LUNG CIRCULATION, OXIGENATED LUNG FUNCTION].

    Science.gov (United States)

    Nikolaeva, I P; Kapranova, A S; Popova, V B; Lodyagin, A N; Frolova, T A

    2015-01-01

    The authors measured the changes of hemodynamics in 72 patients. It was also estimated a blood oxygenation and volume of liquid sectors of the organism in different degree of obesity before and after liposuction of the large volume. It was shown, that this operation facilitated to an improvement of respiratory lung function due to changes of pulmonary circulation.

  1. Study of Preparation of Large Area Standard Source

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    With increasingly widespread application of nuclear technology, many large area contamination detectors are used to measure the contaminated surface by α, β radionuclides in nuclear facilities and isotope production places. To solve the

  2. Sand tank experiment of a large volume biodiesel spill

    Science.gov (United States)

    Scully, K.; Mayer, K. U.

    2015-12-01

    Although petroleum hydrocarbon releases in the subsurface have been well studied, the impacts of subsurface releases of highly degradable alternative fuels, including biodiesel, are not as well understood. One concern is the generation of CH4­ which may lead to explosive conditions in underground structures. In addition, the biodegradation of biodiesel consumes O2 that would otherwise be available for the degradation of petroleum hydrocarbons that may be present at a site. Until now, biodiesel biodegradation in the vadose zone has not been examined in detail, despite being critical to understanding the full impact of a release. This research involves a detailed study of a laboratory release of 80 L of biodiesel applied at surface into a large sandtank to examine the progress of biodegradation reactions. The experiment will monitor the onset and temporal evolution of CH4 generation to provide guidance for site monitoring needs following a biodiesel release to the subsurface. Three CO2 and CH4 flux chambers have been deployed for long term monitoring of gas emissions. CO2 fluxes have increased in all chambers over the 126 days since the start of the experiment. The highest CO2 effluxes are found directly above the spill and have increased from < 0.5 μmol m-2 s-1 to ~3.8 μmol m-2 s-1, indicating an increase in microbial activity. There were no measurable CH4 fluxes 126 days into the experiment. Sensors were emplaced to continuously measure O2, CO2, moisture content, matric potential, EC, and temperature. In response to the release, CO2 levels have increased across all sensors, from an average value of 0.1% to 0.6% 126 days after the start of the experiment, indicating the rapid onset of biodegradation. The highest CO2 values observed from samples taken in the gas ports were 2.5%. Average O2 concentrations have decreased from 21% to 17% 126 days after the start of the experiment. O2 levels in the bottom central region of the sandtank declined to approximately 12%.

  3. Large Variations in Ice Volume During the Middle Eocene "Doubthouse"

    Science.gov (United States)

    Dawber, C. F.; Tripati, A. K.

    2008-12-01

    The onset of glacial conditions in the Cenozoic is widely held to have begun ~34 million years ago, coincident with the Eocene-Oligocene boundary1. Warm and high pCO2 'greenhouse' intervals such as the Eocene are generally thought to be ice-free2. Yet the sequence stratigraphic record supports the occurrence of high-frequency sea-level change of tens of meters in the Middle and Late Eocene3, and large calcite and seawater δ18O excursions (~0.5-1.0 permil) have been reported in foraminifera from open ocean sediments4. As a result, the Middle Eocene is often considered the intermediary "doubthouse". The extent of continental ice during the 'doubthouse' is controversial, with estimates of glacioeustatic sea level fall ranging from 30 to 125m2,3,5. We present a new δ18Osw reconstruction for Ocean Drilling Project (ODP) Site 1209 in the tropical Pacific Ocean. It is the first continuous high-resolution record for an open-ocean site that is not directly influenced by changes in the carbonate compensation depth, which enables us to circumvent many of the limitations of existing records. Our record shows increases of 0.8 ± 0.2 (1 s.e) permil and 1.1 ± 0.2 permil at ~44-45 and ~42-41 Ma respectively, which suggests glacioeustatic sea level variations of ~90 m during the Middle Eocene. Modelling studies have shown that fully glaciating Antarctica during the Eocene should drive a change in seawater (δ18Osw) of 0.45 permil, and lower sea level by ~55 m6. Our results therefore support significant ice storage in both the Northern and Southern Hemisphere during the Middle Eocene 'doubthouse'. 1.Miller, Kenneth G. et al., 1990, Eocene-Oligocene sea-level changes in the New Jersey coastal plain linked to the deep-sea record. Geological Society of America Bulletin 102, 331-339 2.Pagani, M. et al., 2005, Marked decline in atmospheric carbon dioxide concentrations during the Paleogene. Science 309 (5734), 600-603. 3.Browning, J., Miller, K., and Pak, D., 1996, Global implications

  4. LARGE VOLUME IONIZATION CHAMBER USED AS LABORATORY REFERENCE FOR LOW ENERGY X—RAY MEASUREMENT

    Institute of Scientific and Technical Information of China (English)

    杨国山; 薛永库; 等

    1994-01-01

    A large volume spherical ionization chamber of 195mm diameter and 0.36mg/cm2 wall thickness made from conducting carbon-fibre epoxy composite material has been developed.The mechanical intensity of the chamber is satisfactory for a good longterm volume stability.Owing to its large volume and thin wall,the chamber is sensitive to low energy photon beams and has excellent energy-response characteristics.This ionization chamber is suitable not only for a laboratory reference but also for measurement of low energy photon beam exposure rates at protection-level.

  5. Preparing Students with Learning Disabilities for Large-Scale Writing Assessments

    Science.gov (United States)

    Olinghouse, Natalie G.; Colwell, Ryan P.

    2013-01-01

    This article provides recommendations for teachers to better prepare 3rd through 12th grade students with learning disabilities for large-scale writing assessments. The variation across large-scale writing assessments and the multiple needs of struggling writers indicate the need for test preparation to be embedded within a comprehensive,…

  6. Large volume production of large size GaAs substrates and epitaxial wafers for microwave devices

    OpenAIRE

    Otoki, Y.; Kamogawa, H.; Ohnishi, M.; Inada, T.; Kashiwa, M.; Sakaguchi, H.

    1999-01-01

    Recent mass production techniques for LEC substrates and MOVPE wafers for microwave devices are described. Huge GaAs semi-insulating ingots (150mm diam., 310mm long) was obtained by Multi-hot-zone very large size pullar. Three step boule annealing and fully-automated process enabled mass production of the large size substrates. Epitaxiial wafers with abrupt hetero interface, excellent uniformity and reproducibility are producing largely by face down horizontal flow type MOVPE system, which ca...

  7. Electrolyte and Haemogram changes post large volume liposuction comparing two different tumescent solutions

    Directory of Open Access Journals (Sweden)

    Kumar Vivek

    2014-01-01

    Full Text Available Background: The most common definitions of large volume liposuction refer to total 5 l volume aspiration during a single procedure (fat plus wetting solution. Profound haemodynamic and metabolic alterations can accompany large volume liposuction. Due to paucity of literature on the effect of different tumescent solutions on the electrolyte balance and haematological changes during large volume liposuction, we carried out this study using two different wetting solutions to study the same. Materials and Methods: Total 30 patients presenting with varying degrees of localized lipodystrophy in different body regions were enrolled for the study. Prospective randomized controlled trial was conducted by Department of Plastic and Cosmetic Surgery, Sir Ganga Ram Hospital, New Delhi from January 2011 to June 2012. Patients were randomized into two groups of 15 patients each by using computer generated random numbers. Tumescent formula used for Group A (normal saline [NS] was our modification of Klein′s Formula and Tumescent formula used for Group B (ringer lactate [RL] was our modification of Hunstadt′s formula. Serum electrolytes and hematocrit levels were done at preinduction, immediate postoperative period and postoperative day 1. Result: Statistical analysis was performed using SPSS software version 15.0. Which showed statistically significant electrolytes and hematocrit changes occur during large volume liposuction. Conclusion: Statistically significant electrolytes and hematocrit changes occur during large volume liposuction and patients should be kept under observation of anaesthesist for at least 24 h. Patients require strict monitoring of vital parameters and usually Intensive Care Unit is not required. There was no statistical difference in the electrolyte changes using NS or RL as tumescent solution and both solutions were found safe for large volume liposuction.

  8. An immunomagnetic separator for concentration of pathogenic micro-organisms from large volume samples

    Energy Technology Data Exchange (ETDEWEB)

    Rotariu, Ovidiu [School of Biological Sciences, University of Aberdeen, Cruickshank Building, St. Machar Drive, Aberdeen (United Kingdom) and National Institute of R-D for Technical Physics I.F.T. Iasi, Mangeron 47 Blvd., Iasi (Romania)]. E-mail: o.rotariu@abdn.ac.uk; Ogden, Iain D. [Department of Medical Microbiology, University of Aberdeen, Aberdeen (United Kingdom); MacRae, Marion [Department of Medical Microbiology, University of Aberdeen, Aberdeen (United Kingdom); Badescu, Vasile [National Institute of R-D for Technical Physics I.F.T. Iasi, Mangeron 47 Blvd., Iasi (Romania); Strachan, Norval J.C. [School of Biological Sciences, University of Aberdeen, Cruickshank Building, St. Machar Drive, Aberdeen (United Kingdom)

    2005-05-15

    The standard method of immunomagnetic separation of pathogenic bacteria from food and environmental matrices processes 1 ml volumes. Pathogens present at low levels (<1 pathogenic bacteria per ml) will not be consistently detected by this method. Here a flow through immunomagnetic separator (FTIMS) has been designed and tested to process large volume samples (>50 ml). Preliminary results show that between 70 and 113 times more Escherchia coli O157 are recovered compared with the standard 1 ml method.

  9. [Preparation of large area Al-ZnO thin film by DC magnetron sputtering].

    Science.gov (United States)

    Jiao, Fei; Liao, Cheng; Han, Jun-Feng; Zhou, Zhen

    2009-03-01

    Solar cells of p-CIS/n-buffer/ZnO type, where CIS is (CuInS2, CuInSe2 or intermediates, are thin-film-based devices for the future high-efficiency and low-cost photovoltaic devices. As important thin film, the properties of Al-doped ZnO (AZO) directly affect the parameter of the cell, especially for large volume. In the present paper, AZO semiconductor transparent thin film on soda-lime glass was fabricated using cylindrical zinc-aluminum target, which can not only lower the cost of the target but also make the preparation of large area AZO thin film more easily. Using the DC magnet sputtering techniques and rolling target, high utilization efficiency of target was achieved and large area uniform and directional film was realized. An introduction to DC magnet sputtering techniques for large area film fabrication is given. With different measurement methods, such as X-ray diffraction (XRD) and scan electron microscope (SEM), we analyzed large size film's structure, appearance, and electrical and optical characteristics. The XRD spectrum indicated that the AZO film shows well zinc-blende structure with a preferred (002) growth and the c-axis is oriented normal to the substrate plane. The lattice constant is 5.603 9 nm and the mismatch with CdS thin film is only 2 percent. It absolutely satisfied the demand of the GIGS solar cell. The cross-section of the AZO thin film indicates the columnar structure and the surface morphology shows that the crystal size is about 50 nm that is consistent with the result of XRD spectrum. By the optical transmission curve, not only the high transmission rate over 85 percent in the visible spectrum between 400 nm and 700 nm was showed but also the band gap 3.1 eV was estimated. And all these parameters can meet the demand of the large area module of GIGS solar cell. The result is that using alloy target and Ar gas, and controlling the appropriate pressure of oxygen, we can get directional, condensed, uniform, high transmitting rate, low

  10. Serial sectioning and electron microscopy of large tissue volumes for 3D analysis and reconstruction: a case study of the calyx of Held.

    Science.gov (United States)

    Hoffpauir, Brian K; Pope, Brian A; Spirou, George A

    2007-01-01

    Serial section electron microscopy is typically applied to investigation of small tissue volumes encompassing subcellular structures. However, in neurobiology, the need to relate subcellular structure to organization of neural circuits can require investigation of large tissue volumes at ultrastructural resolution. Analysis of ultrastructure and three-dimensional reconstruction of even one to a few cells is time consuming, and still does not generate the necessary numbers of observations to form well-grounded insights into biological principles. We describe an assemblage of existing computer-based methods and strategies for graphical analysis of large photographic montages to accomplish the study of multiple neurons through large tissue volumes. Sample preparation, data collection and subsequent analyses can be completed within 3-4 months. These methods generate extremely large data sets that can be mined in future studies of nervous system organization.

  11. Refined universal laws for hull volumes and perimeters in large planar maps

    Science.gov (United States)

    Guitter, Emmanuel

    2017-07-01

    We consider ensembles of planar maps with two marked vertices at distance k from each other, and look at the closed line separating these vertices and lying at distance d from the first one (d  faces within the hull is called the hull volume, and the length of the separating line the hull perimeter. We study the statistics of the hull volume and perimeter for arbitrary d and k in the limit of infinitely large planar quadrangulations, triangulations and Eulerian triangulations. We consider more precisely situations where both d and k become large with the ratio d/k remaining finite. For infinitely large maps, two regimes may be encountered: either the hull has a finite volume and its complementary is infinitely large, or the hull itself has an infinite volume and its complementary is of finite size. We compute the probability for the map to be in either regime as a function of d/k as well as a number of universal statistical laws for the hull perimeter and volume when maps are conditioned to be in one regime or the other.

  12. Simple room-temperature preparation of high-yield large-area graphene oxide.

    Science.gov (United States)

    Huang, N M; Lim, H N; Chia, C H; Yarmo, M A; Muhamad, M R

    2011-01-01

    Graphene has attracted much attention from researchers due to its interesting mechanical, electrochemical, and electronic properties. It has many potential applications such as polymer filler, sensor, energy conversion, and energy storage devices. Graphene-based nanocomposites are under an intense spotlight amongst researchers. A large amount of graphene is required for preparation of such samples. Lately, graphene-based materials have been the target for fundamental life science investigations. Despite graphene being a much sought-after raw material, the drawbacks in the preparation of graphene are that it is a challenge amongst researchers to produce this material in a scalable quantity and that there is a concern about its safety. Thus, a simple and efficient method for the preparation of graphene oxide (GO) is greatly desired to address these problems. In this work, one-pot chemical oxidation of graphite was carried out at room temperature for the preparation of large-area GO with ~100% conversion. This high-conversion preparation of large-area GO was achieved using a simplified Hummer's method from large graphite flakes (an average flake size of 500 μm). It was found that a high degree of oxidation of graphite could be realized by stirring graphite in a mixture of acids and potassium permanganate, resulting in GO with large lateral dimension and area, which could reach up to 120 μm and ~8000 μm(2), respectively. The simplified Hummer's method provides a facile approach for the preparation of large-area GO.

  13. Analytical Chemistry Laboratory (ACL) procedure compendium. Volume 2, Sample preparation methods

    Energy Technology Data Exchange (ETDEWEB)

    1993-08-01

    This volume contains the interim change notice for sample preparation methods. Covered are: acid digestion for metals analysis, fusion of Hanford tank waste solids, water leach of sludges/soils/other solids, extraction procedure toxicity (simulate leach in landfill), sample preparation for gamma spectroscopy, acid digestion for radiochemical analysis, leach preparation of solids for free cyanide analysis, aqueous leach of solids for anion analysis, microwave digestion of glasses and slurries for ICP/MS, toxicity characteristic leaching extraction for inorganics, leach/dissolution of activated metal for radiochemical analysis, extraction of single-shell tank (SST) samples for semi-VOC analysis, preparation and cleanup of hydrocarbon- containing samples for VOC and semi-VOC analysis, receiving of waste tank samples in onsite transfer cask, receipt and inspection of SST samples, receipt and extrusion of core samples at 325A shielded facility, cleaning and shipping of waste tank samplers, homogenization of solutions/slurries/sludges, and test sample preparation for bioassay quality control program.

  14. Research on Controlled Volume Operation Method of Large-scale Water Transfer Canal

    Institute of Scientific and Technical Information of China (English)

    DING Zhiliang; WANG Changde; XU Duo; XIAO Hua

    2011-01-01

    The controlled volume method of operation is especially suitable for large-scale water delivery canal system with complex operation requirements. An operating simulation model based on the storage volume control method for multi-reach canal system in series was established. In allusion to the deficiency of existing controlled volume algorithm, the improved controlled volume algorithm of the whole canal pools was proposed, and the simulation results indicated that the storage volume and water level of each canal pool could be accurately controlled after the improved algorithm had been adopted. However, for some typical discharge demand operating conditions, if the previously mentioned algorithm was adopted, then it certainly would cause some unnecessary gate adjustments, and consequently the disturbed canal pools would be increased. Therefore, the idea of controlled volume operation method of continuous canal pools was proposed, and corresponding algorithm was designed. Through simulating practical project, the results indicated that the new controlled volume algorithm proposed for typical operating conditions could comparatively and obviously reduce the number of regulated check gates and disturb canal pools for some typical discharge demand operating conditions, thus the control efficiency of canal system could be improved.

  15. Optimization of the electric field distribution in a large volume tissue-equivalent proportional counter

    Energy Technology Data Exchange (ETDEWEB)

    Verma, P.K.; Waker, A.J. (Leeds Univ. (United Kingdom). Dept. of Medical Physics)

    1992-10-01

    Large volume tissue-equivalent proportional counters are of interest in radiation protection metrology, as the sensitivity in terms of counts per unit absorbed dose in these devices increases as the square of the counter diameter. Conventional solutions to the problem of maintaining a uniform electric field within a counter result in sensitive volume to total volume ratios which are unacceptably low when counter dimensions of the order of 15 cm diameter are considered and when overall compactness is an important design criterion. This work describes the design and optimization of an arrangement of field discs set at different potentials which enable sensitive volume to total volume ratios to approach unity. The method has been used to construct a 12.7 cm diameter right-cylindrical tissue-equivalent proportional counter in which the sensitive volume accounts for over 95% of the total device volume and the gas gain uniformity is maintained to within 3% along the entire length of the anode wire. (author).

  16. Rapid estimate of solid volume in large tuff cores using a gas pycnometer

    Energy Technology Data Exchange (ETDEWEB)

    Thies, C. [ed.; Geddis, A.M.; Guzman, A.G. [and others

    1996-09-01

    A thermally insulated, rigid-volume gas pycnometer system has been developed. The pycnometer chambers have been machined from solid PVC cylinders. Two chambers confine dry high-purity helium at different pressures. A thick-walled design ensures minimal heat exchange with the surrounding environment and a constant volume system, while expansion takes place between the chambers. The internal energy of the gas is assumed constant over the expansion. The ideal gas law is used to estimate the volume of solid material sealed in one of the chambers. Temperature is monitored continuously and incorporated into the calculation of solid volume. Temperature variation between measurements is less than 0.1{degrees}C. The data are used to compute grain density for oven-dried Apache Leap tuff core samples. The measured volume of solid and the sample bulk volume are used to estimate porosity and bulk density. Intrinsic permeability was estimated from the porosity and measured pore surface area and is compared to in-situ measurements by the air permeability method. The gas pycnometer accommodates large core samples (0.25 m length x 0.11 m diameter) and can measure solid volume greater than 2.20 cm{sup 3} with less than 1% error.

  17. A universal and flexible theodolite-camera system for making accurate measurements over large volumes

    Science.gov (United States)

    Zhang, Xiaohu; Zhu, Zhaokun; Yuan, Yun; Li, Lichun; Sun, Xiangyi; Yu, Qifeng; Ou, Jianliang

    2012-11-01

    Typically, optical measurement systems can achieve high accuracy over a limited volume, or cover a large volume with low accuracy. In this paper, we propose a universal way of integrating a camera with a theodolite to construct a theodolite-camera (TC) measurement system that can make measurements over a large volume with high accuracy. The TC inherits the advantages of high flexibility and precision from theodolite and camera, but it avoids the need to perform elaborate adjustments on the camera and theodolite. The TC provides a universal and flexible approach to the camera-on-theodolite system. We describe three types of TC based separately on: (i) a total station; (ii) a theodolite; and (iii) a general rotation frame. We also propose three corresponding calibration methods for the different TCs. Experiments have been conducted to verify the measuring accuracy of each of the three types of TC.

  18. SparseLeap: Efficient Empty Space Skipping for Large-Scale Volume Rendering

    KAUST Repository

    Hadwiger, Markus

    2017-08-28

    Recent advances in data acquisition produce volume data of very high resolution and large size, such as terabyte-sized microscopy volumes. These data often contain many fine and intricate structures, which pose huge challenges for volume rendering, and make it particularly important to efficiently skip empty space. This paper addresses two major challenges: (1) The complexity of large volumes containing fine structures often leads to highly fragmented space subdivisions that make empty regions hard to skip efficiently. (2) The classification of space into empty and non-empty regions changes frequently, because the user or the evaluation of an interactive query activate a different set of objects, which makes it unfeasible to pre-compute a well-adapted space subdivision. We describe the novel SparseLeap method for efficient empty space skipping in very large volumes, even around fine structures. The main performance characteristic of SparseLeap is that it moves the major cost of empty space skipping out of the ray-casting stage. We achieve this via a hybrid strategy that balances the computational load between determining empty ray segments in a rasterization (object-order) stage, and sampling non-empty volume data in the ray-casting (image-order) stage. Before ray-casting, we exploit the fast hardware rasterization of GPUs to create a ray segment list for each pixel, which identifies non-empty regions along the ray. The ray-casting stage then leaps over empty space without hierarchy traversal. Ray segment lists are created by rasterizing a set of fine-grained, view-independent bounding boxes. Frame coherence is exploited by re-using the same bounding boxes unless the set of active objects changes. We show that SparseLeap scales better to large, sparse data than standard octree empty space skipping.

  19. The impact of large tidal volume ventilation on the absorption of inhaled insulin in rabbits

    DEFF Research Database (Denmark)

    Petersen, Astrid Heide; Laursen, Torben; Ahrén, Bo;

    2007-01-01

    Previous studies have shown that ventilation patterns affect absorption of inhaled compounds. Thus, the aim of this study was to investigate the effect of large tidal volume ventilation (LTVV) on the absorption of inhaled insulin in rabbits. Mechanically ventilated rabbits were given human insuli...

  20. Populating the Large-Wavevector Realm: Bloch Volume Plasmon Polaritons in Hyperbolic and Extremely Anisotropic Metamaterials

    DEFF Research Database (Denmark)

    Zhukovsky, Sergei; Babicheva, Viktoriia; Orlov, A. A.

    2014-01-01

    Optics of hyperbolic metamaterials is revisited in terms of large-wavevector waves, evanescent in isotropic media but propagating in presence of extreme anisotropy. Identifying the physical nature of these waves as Bloch volume plasmon polaritons, we derive their existence conditions and outline...... the strategy for tailoring their properties in multiscale metamaterials....

  1. Development of a Solid Phase Extraction Method for Agricultural Pesticides in Large-Volume Water Samples

    Science.gov (United States)

    An analytical method using solid phase extraction (SPE) and analysis by gas chromatography/mass spectrometry (GC/MS) was developed for the trace determination of a variety of agricultural pesticides and selected transformation products in large-volume high-elevation lake water sa...

  2. Large volume liquid silicone injection in the upper thighs : a never ending story

    NARCIS (Netherlands)

    Hofer, SOP; Damen, A; Nicolai, JPA

    2000-01-01

    This report concerns a 26-year-old male-to-female transsexual who had received a large volume liquid silicone injection of unknown grade into her upper lateral thighs to gain female contour. She presented at our outpatient clinic 4 years after the silicone injection with complaints of pain and silic

  3. Capillary gas chromatographic analysis of nerve agents using large volume injections

    NARCIS (Netherlands)

    Degenhardt, C.E.A.M.; Kientz, C.E.

    1996-01-01

    The use of large volume injections has been studied for the verification of intact organophosphorus chemical warfare agents in water samples. As the use of ethyl acetate caused severe detection problems new potential solvents were evaluated. With the developed procedure, the nerve agents sarin, tabu

  4. Study of special performance and volume training loadings at swimmers in the year preparation

    Directory of Open Access Journals (Sweden)

    Balamutova N.M.

    2014-01-01

    Full Text Available Purpose : to study the dynamics of the special performance and volume of training load during annual training swimmers. Material / Methods : The study involved 14 teams of students of Kharkiv universities. All swimmers are of high qualification. Motor tests of special performance swimmers, functional tests were used to confirm the effectiveness of the training process. Results : The dynamics of special performance indicators and volume of training load of highly qualified swimmers in the annual cycle of training. Determined part of aerobic (58.3 %, aerobic- anaerobic special (34.5%, anaerobic- glycolytic (5.5%, anaerobic- alactate (1.7% loadings in the direction of total training load for the academic year. Conclusions : In preparing swimmers stayer is the most appropriate single-cycle construction of the annual cycle, and for swimmers, sprinters should be based on two-cycle version of the load distribution.

  5. Low-cost preparation of mesoporous silica with high pore volume

    Institute of Scientific and Technical Information of China (English)

    Shuling Shen; Wei Wu; Kai Guo; Jianfeng Chen

    2007-01-01

    Mesoporous silica materials with high pore volume were successfully prepared by the chemical precipitation method, with water glass and a biodegradable nonionic surfactant polyethylene glycol (PEG). The obtained materials were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), thermo gravimetric analyzer and differential scanning calorimetry (TG-DSC), nitrogen adsorption-desorption measurements, and X-ray diffraction (XRD). The results showed that the changes of the pore parameters depended on both the surfactant content and heat treatment temperature. When the content of PEG was 10wt% and the obtained PEG/SiO2 composite was heated at 600℃, the mesoporous silica with a pore volume of 2.2 cm3/g, a BET specific surface area of 361.55 m2/g, and a diameter of 2-4 μm could be obtained. The obtained mesoporous silica materials have potential applications in the fields of paint and plastic, as thickening, reinforcing, and flatting agents.

  6. GPU-Based 3D Cone-Beam CT Image Reconstruction for Large Data Volume

    Directory of Open Access Journals (Sweden)

    Xing Zhao

    2009-01-01

    Full Text Available Currently, 3D cone-beam CT image reconstruction speed is still a severe limitation for clinical application. The computational power of modern graphics processing units (GPUs has been harnessed to provide impressive acceleration of 3D volume image reconstruction. For extra large data volume exceeding the physical graphic memory of GPU, a straightforward compromise is to divide data volume into blocks. Different from the conventional Octree partition method, a new partition scheme is proposed in this paper. This method divides both projection data and reconstructed image volume into subsets according to geometric symmetries in circular cone-beam projection layout, and a fast reconstruction for large data volume can be implemented by packing the subsets of projection data into the RGBA channels of GPU, performing the reconstruction chunk by chunk and combining the individual results in the end. The method is evaluated by reconstructing 3D images from computer-simulation data and real micro-CT data. Our results indicate that the GPU implementation can maintain original precision and speed up the reconstruction process by 110–120 times for circular cone-beam scan, as compared to traditional CPU implementation.

  7. Understanding Subcutaneous Tissue Pressure for Engineering Injection Devices for Large-Volume Protein Delivery.

    Science.gov (United States)

    Doughty, Diane V; Clawson, Corbin Z; Lambert, William; Subramony, J Anand

    2016-07-01

    Subcutaneous injection allows for self-administration of monoclonal antibodies using prefilled syringes, autoinjectors, and on-body injector devices. However, subcutaneous injections are typically limited to 1 mL due to concerns of injection pain from volume, viscosity, and formulation characteristics. Back pressure can serve as an indicator for changes in subcutaneous mechanical properties leading to pain during injection. The purpose of this study was to investigate subcutaneous pressures and injection site reactions as a function of injection volume and flow rate. A pressure sensor in the fluid path recorded subcutaneous pressures in the abdomen of Yorkshire swine. The subcutaneous tissue accommodates large-volume injections and with little back pressure as long as low flow rates are used. A 1 mL injection in 10 seconds (360 mL/h flow rate) generated a pressure of 24.0 ± 3.4 kPa, whereas 10 mL delivered in 10 minutes (60 mL/h flow rate) generated a pressure of 7.4 ± 7.8 kPa. After the injection, the pressure decays to 0 over several seconds. The subcutaneous pressures and mechanical strain increased with increasing flow rate but not increasing dose volume. These data are useful for the design of injection devices to mitigate back pressure and pain during subcutaneous large-volume injection. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

  8. Large Eddy Simulations of Volume Restriction Effects on Canopy-Induced Increased-Uplift Regions

    Science.gov (United States)

    Chatziefstratiou, E.; Bohrer, G.; Velissariou, V.

    2012-12-01

    ABSTRACT Previous modeling and empirical work have shown the development of important areas of increased uplift past forward-facing steps, and recirculation zones past backward-facing steps. Forests edges represent a special kind of step - a semi-porous one. Current models of the effects of forest edges on the flow represent the forest with a prescribed drag term and does not account for the effects of the solid volume in the forest that restrict the airflow. The RAMS-based Forest Large Eddy Simulation (RAFLES) resolves flows inside and above forested canopies. RAFLES is spatially explicit, and uses the finite volume method to solve a descretized set of Navier-Stokes equations. It accounts for vegetation drag effects on the flow and on the flux exchange between the canopy and the canopy air, proportional to the local leaf density. For a better representation of the vegetation structure in the numerical grid within the canopy sub-domain, the model uses a modified version of the cut cell coordinate system. The hard volume of vegetation elements, in forests, or buildings, in urban environments, within each numerical grid cell is represented via a sub-grid-scale process that shrinks the open apertures between grid cells and reduces the open cell volume. We used RAFLES to simulate the effects of a canopy of varying foliage and stem densities on flow over virtual qube-shaped barriers under neutrally buoyant conditions. We explicitly tested the effects of the numerical representation of volume restriction, independent of the effects of the leaf drag by comparing drag-only simulations, where we prescribed no volume or aperture restriction to the flow, restriction-only simulations, where we prescribed no drag, and control simulations, where both drag and volume plus aperture restriction were included. Our simulations show that representation of the effects of the volume and aperture restriction due to obstacles to flow is important (figure 1) and leads to differences in the

  9. Large-Scale Multi-Resolution Representations for Accurate Interactive Image and Volume Operations

    KAUST Repository

    Sicat, Ronell B.

    2015-11-25

    The resolutions of acquired image and volume data are ever increasing. However, the resolutions of commodity display devices remain limited. This leads to an increasing gap between data and display resolutions. To bridge this gap, the standard approach is to employ output-sensitive operations on multi-resolution data representations. Output-sensitive operations facilitate interactive applications since their required computations are proportional only to the size of the data that is visible, i.e., the output, and not the full size of the input. Multi-resolution representations, such as image mipmaps, and volume octrees, are crucial in providing these operations direct access to any subset of the data at any resolution corresponding to the output. Despite its widespread use, this standard approach has some shortcomings in three important application areas, namely non-linear image operations, multi-resolution volume rendering, and large-scale image exploration. This dissertation presents new multi-resolution representations for large-scale images and volumes that address these shortcomings. Standard multi-resolution representations require low-pass pre-filtering for anti- aliasing. However, linear pre-filters do not commute with non-linear operations. This becomes problematic when applying non-linear operations directly to any coarse resolution levels in standard representations. Particularly, this leads to inaccurate output when applying non-linear image operations, e.g., color mapping and detail-aware filters, to multi-resolution images. Similarly, in multi-resolution volume rendering, this leads to inconsistency artifacts which manifest as erroneous differences in rendering outputs across resolution levels. To address these issues, we introduce the sparse pdf maps and sparse pdf volumes representations for large-scale images and volumes, respectively. These representations sparsely encode continuous probability density functions (pdfs) of multi-resolution pixel

  10. Comparative Studies on Preparation of Large Plant DNA Fragments by Pulse Field Gel Electrophoresis

    Institute of Scientific and Technical Information of China (English)

    Yang Jiliang(杨继良); Wang Qinghua(王庆华); Deng Daiyong; Yang Dianer; Jin Demin; Weng Manli; Zhang Juren; Wang Bin

    2004-01-01

    The preparation of large plant DNA fragments is extremely important to the construction of large insert DNA libraries (YAC, BAC, PAC and TAC). Although several techniques have been developed in each step of large plant DNA fragments preparation, the whole processing remains complicated and difficult. Based on authors research experience and the recent worldwide development in this field, the following aspects are discussed in this paper: techniques of plant high molecular weight (HMW) DNA purification by pre-electrophoresis, the optimal conditions for the partial digestion of the HMW DNA by HindIII, the isolation effects of of large plant DNA fragments (100~400 kb) with different parameters of pulse field gel electrophoresis (PFGE), and the recovery of large DNA fragments. Through comparative studies, the advantages and disadvantages of each technique are discussed and some recommendations are proposed for preparing high quality large plant DNA fragments. The suggested techniques have been used in preparing the large DNA fragments of maize, rice, moss, laver, sea tangle and peach,and similar results are obtained among all the materials. This paper only reports the results using maize as material.

  11. Some observations on the origins of large volumes of carbon dioxide accumulations in sedimentary basins

    Energy Technology Data Exchange (ETDEWEB)

    Wycherley, H. [Natural History Museum, London (United Kingdom). Dept. of Mineralogy; Imperial College, London (United Kingdom). TH Huxley School of Environment, Earth Science and Engineering; Fleet, A. [Natural History Museum, London (United Kingdom). Dept. of Mineralogy; Shaw, H. [Imperial College, London (United Kingdom). TH Huxley School of Environment, Earth Science and Engineering

    1999-10-01

    Large volumes of carbon dioxide (i.e. up to 90 v/v%) have been encountered in sedimentary basins from various geological settings but their origins remain enigmatic. Evidence from carbon and noble gas isotope analyses indicate a variety of interpretations for the origins of the CO{sub 2} including mantle degassing, metamorphic reactions or magmatic processes. The formation of large accumulations of large volumes of CO{sub 2} in sedimentary basins is discussed with specific reference to published data from the Pannonian Basin, Hungary; the Cooper-Eromanga Basin, Australia; and the South Viking Graben, North Sea. These basins have occurrences of large volumes (i.e. over 15 v/v%) of isotopically heavy carbon dioxide (thought to be of inorganic origin), and, although they differ somewhat in terms of sedimentary fill, all have major structural features close to the gas accumulations. The available geochemical data are currently neither sufficient to confirm the specific origin(s) of the CO{sub 2} (e.g. mantle-derived. carbonate metamorphism) nor unscramble CO{sub 2} mixed from two or more sources; ongoing studies, especially those involving noble gas analyses, should provide fuller answers. (author)

  12. The large observatories maintenance management: tools and strategies for maintenance manuals preparation

    Science.gov (United States)

    Formentin, F.; Pozzobon, M.; Marchiori, G.; Busatta, A.; Giacomel, L.

    2010-07-01

    Large Observatories require enormous efforts in preparing the Maintenance Manuals. The possibility to adopt a standardised system, associated to centralized data base and software tools is investigated. This strategy implies a revolution of Maintenance Manuals: from information collection (paper-based), to a modular approach where data modules are used. The initial efforts associated to data modules preparation is compensated by several benefits (time savings for end-users, reduced training requirements, reduced equipment down-time). Moreover, cost savings in the preparation process, even for different equipment, is also possible. Finally, this standardised strategy will assure compatibility between different programs or partners.

  13. MAD about the Large Magellanic Cloud: preparing for the era of Extremely Large Telescopes

    CERN Document Server

    Fiorentino, G; Diolaiti, E; Valenti, E; Cignoni, M; Mackey, A D

    2011-01-01

    We present J, H, Ks photometry from the the Multi conjugate Adaptive optics Demonstrator (MAD), a visitor instrument at the VLT, of a resolved stellar population in a small crowded field in the bar of the Large Magellanic Cloud near the globular cluster NGC 1928. In a total exposure time of 6, 36 and 20 minutes, magnitude limits were achieved of J \\sim 20.5 mag, H \\sim 21 mag, and Ks \\sim20.5 mag respectively, with S/N> 10. This does not reach the level of the oldest Main Sequence Turnoffs, however the resulting Colour-Magnitude Diagrams are the deepest and most accurate obtained so far in the infrared for the LMC bar. We combined our photometry with deep optical photometry from the Hubble Space Telescope/Advanced Camera for Surveys, which is a good match in spatial resolution. The comparison between synthetic and observed CMDs shows that the stellar population of the field we observed is consistent with the star formation history expected for the LMC bar, and that all combinations of IJHKs filters can, with ...

  14. Lossless compression of very large volume data with fast dynamic access

    Science.gov (United States)

    Zhao, Rongkai; Tao, Tao; Gabriel, Michael; Belford, Geneva

    2002-09-01

    The volumetric data set is important in many scientific and biomedical fields. Since such sets may be extremely large, a compression method is critical to store and transmit them. To achieve a high compression rate, most of the existing volume compression methods are lossy, which is usually unacceptable in biomedical applications. We developed a new context-based non-linear prediction method to preprocess the volume data set in order to effectively lower the prediction entropy. The prediction error is further encoded using Huffman code. Unlike the conventional methods, the volume is divided into cubical blocks to take advantage of the data's spatial locality. Instead of building one Huffman tree for each block, we developed a novel binning algorithm that build a Huffman tree for each group (bin) of blocks. Combining all the effects above, we achieved an excellent compression rate compared to other lossless volume compression methods. In addition, an auxiliary data structure, Scalable Hyperspace File (SHSF) is used to index the huge volume so that we can obtain many other benefits including parallel construction, on-the-fly accessing of compressed data without global decompression, fast previewing, efficient background compressing, and scalability etc.

  15. Measurement of atmospheric neutrino oscillations with very large volume neutrino telescopes

    CERN Document Server

    Yañez, J P

    2015-01-01

    Neutrino oscillations have been probed during the last few decades using multiple neutrino sources and experimental set-ups. In the recent years, very large volume neutrino telescopes have started contributing to the field. First ANTARES and then IceCube have relied on large and sparsely instrumented volumes to observe atmospheric neutrinos for combinations of baselines and energies inaccessible to other experiments. Using this advantage, the latest result from IceCube starts approaching the precision of other established technologies, and is paving the way for future detectors, such as ORCA and PINGU. These new projects seek to provide better measurements of neutrino oscillation parameters, and eventually determine the neutrino mass ordering. The results from running experiments and the potential from proposed projects are discussed in this review, emphasizing the experimental challenges involved in the measurements.

  16. Measurement of Atmospheric Neutrino Oscillations with Very Large Volume Neutrino Telescopes

    Directory of Open Access Journals (Sweden)

    J. P. Yáñez

    2015-01-01

    Full Text Available Neutrino oscillations have been probed during the last few decades using multiple neutrino sources and experimental set-ups. In the recent years, very large volume neutrino telescopes have started contributing to the field. First ANTARES and then IceCube have relied on large and sparsely instrumented volumes to observe atmospheric neutrinos for combinations of baselines and energies inaccessible to other experiments. Using this advantage, the latest result from IceCube starts approaching the precision of other established technologies and is paving the way for future detectors, such as ORCA and PINGU. These new projects seek to provide better measurements of neutrino oscillation parameters and eventually determine the neutrino mass ordering. The results from running experiments and the potential from proposed projects are discussed in this review, emphasizing the experimental challenges involved in the measurements.

  17. Comprehensive workflow for wireline fluid sampling in an unconsolidated formations utilizing new large volume sampling equipment

    Energy Technology Data Exchange (ETDEWEB)

    Kvinnsland, S.; Brun, M. [TOTAL EandP Norge (Norway); Achourov, V.; Gisolf, A. [Schlumberger (Canada)

    2011-07-01

    Precise and accurate knowledge of fluid properties is essential in unconsolidated formations to the design of production facilities. Wireline formation testers (WFT) have a wide range of applications and the latest WFT can be used to define fluid properties in the wells drilled with oil based mud (OBM) by acquiring PVT and large volume samples. To use these technologies, a comprehensive workflow has to be implemented and the aim of this paper is to present such a workflow. A sampling was conducted in highly unconsolidated sand saturated with biodegradable fluid in the Hild filed in the North Sea. Results showed the use of comprehensive workflow to be successful in obtaining large volume samples with the contamination level below 1%. Oil was precisely characterized thanks to these samples and design updates to the project were made possible. This paper highlighted that the use of the latest WFT technologies can help better characterize fluids in unconsolidated formations and thus optimize production facilities design.

  18. Compatibility of verapamil hydrochloride injection in commonly used large-volume parenterals.

    Science.gov (United States)

    Cutie, M R; Lordi, N G

    1980-05-01

    The visual and chemical compatibilities of verapamil hydrochloride injection in 10 commonly used large-volume solutions packaged in glass, polyolefin, or polyvinyl chloride containers were studied. The mixtures, each containing 40 mg/liter of verapamil hydrochloride, were stored away from light for up to 48 hours at 25 degrees C. The solutions were examined visually for haze, precipitate formation, color change, and evolution of gas immediately after mixing and at 0.25, 1, 3, 8, 24, and 48 hours. Spectrophotometry and thin-layer chromatography were used to test for drug decomposition or chemical incompatibilities. All test methods used showed that no significant degradation of verapamil hydrochloride had taken place in the solutions or through contact with the containers. Slightly higher spectrophotometric readings for dextrose-containing solutions, though within experimental error, could have indicated the presence of dextrose degradation products. Evidence from this study suggests that verapamil hydrocholoride is compatible with the large-volume parenterals studied.

  19. Steady-state probability density function in wave turbulence under large volume limit

    Institute of Scientific and Technical Information of China (English)

    Yeontaek Choia; Sang Gyu Job

    2011-01-01

    We investigate the possibility for two-mode probability density function (PDF) to have a non-zero flux steady state solution. We take the large volume limit so that the space of modes becomes continuous. It is shown that in this limit all the steady-state two- or higher-mode PDFs are the product of one-mode PDFs. The flux of this steady-state solution turns out to be zero for any finite mode PDF.

  20. F-term stabilization of odd axions in LARGE volume scenario

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Xin, E-mail: gaoxin@mppmu.mpg.de [Max-Planck-Institut für Physik (Werner-Heisenberg-Institut), Föhringer Ring 6, 80805 München (Germany); State Key Laboratory of Theoretical Physics, Institute of Theoretical Physics, Chinese Academy of Sciences, P.O. Box 2735, Beijing 100190 (China); Shukla, Pramod, E-mail: shukla@mppmu.mpg.de [Max-Planck-Institut für Physik (Werner-Heisenberg-Institut), Föhringer Ring 6, 80805 München (Germany)

    2014-01-15

    In the context of the LARGE volume scenario, stabilization of axionic moduli is revisited. This includes both even and odd axions with their scalar potential being generated by F-term contributions via various tree-level and non-perturbative effects like fluxed E3-brane instantons and fluxed poly-instantons. In all the cases, we estimate the decay constants and masses of the axions involved.

  1. Low energy prompt gamma-ray tests of a large volume BGO detector

    Energy Technology Data Exchange (ETDEWEB)

    Naqvi, A.A., E-mail: aanaqvi@kfupm.edu.sa [Department of Physics, King Fahd University of Petroleum and Minerals, Dhahran (Saudi Arabia); Kalakada, Zameer [Department of Civil Engineering, King Fahd University of Petroleum and Minerals, Dhahran (Saudi Arabia); Al-Anezi, M.S.; Raashid, M.; Khateeb-ur-Rehman [Department of Physics, King Fahd University of Petroleum and Minerals, Dhahran (Saudi Arabia); Maslehuddin, M. [Center for Engineering Research, King Fahd University of Petroleum and Minerals, Dhahran (Saudi Arabia); Garwan, M.A. [Department of Physics, King Fahd University of Petroleum and Minerals, Dhahran (Saudi Arabia)

    2012-01-15

    Tests of a large volume Bismuth Germinate (BGO) detector were carried out to detect low energy prompt gamma-rays from boron and cadmium-contaminated water samples using a portable neutron generator-based Prompt Gamma Neutron Activation Analysis (PGNAA) setup. Inspite of strong interference between the sample- and the detector-associated prompt gamma-rays, an excellent agreement has been observed between the experimental and calculated yields of the prompt gamma-rays, indicating successful application of the large volume BGO detector in the PGNAA analysis of bulk samples using low energy prompt gamma-rays. - Highlights: Black-Right-Pointing-Pointer Performance tests of a portable neutron generator based PGNAA setup for field measurement. Black-Right-Pointing-Pointer Application of large volume BGO detector in prompt gamma analysis of bulk samples utilizing low energy prompt-gamma rays. Black-Right-Pointing-Pointer Study of interference of boron and cadmium prompt gamma-rays from bulk samples with BGO detector background spectrum.

  2. Scanning laser optical computed tomography system for large volume 3D dosimetry

    Science.gov (United States)

    Dekker, Kurtis H.; Battista, Jerry J.; Jordan, Kevin J.

    2017-04-01

    Stray light causes artifacts in optical computed tomography (CT) that negatively affect the accuracy of radiation dosimetry in gels or solids. Scatter effects are exacerbated by a large dosimeter volume, which is desirable for direct verification of modern radiotherapy treatment plans such as multiple-isocenter radiosurgery. The goal in this study was to design and characterize an optical CT system that achieves high accuracy primary transmission measurements through effective stray light rejection, while maintaining sufficient scan speed for practical application. We present an optical imaging platform that uses a galvanometer mirror for horizontal scanning, and a translation stage for vertical movement of a laser beam and small area detector for minimal stray light production and acceptance. This is coupled with a custom lens-shaped optical CT aquarium for parallel ray sampling of projections. The scanner images 15 cm diameter, 12 cm height cylindrical volumes at 0.33 mm resolution in approximately 30 min. Attenuation coefficients reconstructed from CT scans agreed with independent cuvette measurements within 2% for both absorbing and scattering solutions as well as small 1.25 cm diameter absorbing phantoms placed within a large, scattering medium that mimics gel. Excellent linearity between the optical CT scanner and the independent measurement was observed for solutions with between 90% and 2% transmission. These results indicate that the scanner should achieve highly accurate dosimetry of large volume dosimeters in a reasonable timeframe for clinical application to radiotherapy dose verification procedures.

  3. Scanning laser optical computed tomography system for large volume 3D dosimetry.

    Science.gov (United States)

    Dekker, Kurtis H; Battista, Jerry J; Jordan, Kevin J

    2017-04-07

    Stray light causes artifacts in optical computed tomography (CT) that negatively affect the accuracy of radiation dosimetry in gels or solids. Scatter effects are exacerbated by a large dosimeter volume, which is desirable for direct verification of modern radiotherapy treatment plans such as multiple-isocenter radiosurgery. The goal in this study was to design and characterize an optical CT system that achieves high accuracy primary transmission measurements through effective stray light rejection, while maintaining sufficient scan speed for practical application. We present an optical imaging platform that uses a galvanometer mirror for horizontal scanning, and a translation stage for vertical movement of a laser beam and small area detector for minimal stray light production and acceptance. This is coupled with a custom lens-shaped optical CT aquarium for parallel ray sampling of projections. The scanner images 15 cm diameter, 12 cm height cylindrical volumes at 0.33 mm resolution in approximately 30 min. Attenuation coefficients reconstructed from CT scans agreed with independent cuvette measurements within 2% for both absorbing and scattering solutions as well as small 1.25 cm diameter absorbing phantoms placed within a large, scattering medium that mimics gel. Excellent linearity between the optical CT scanner and the independent measurement was observed for solutions with between 90% and 2% transmission. These results indicate that the scanner should achieve highly accurate dosimetry of large volume dosimeters in a reasonable timeframe for clinical application to radiotherapy dose verification procedures.

  4. Prospects of the search for neutrino bursts from Supernovae with Baksan Large Volume Scintillation Detector

    CERN Document Server

    Petkov, V B

    2015-01-01

    Observing a high-statistics neutrino signal from the supernova explosions in the Galaxy is a major goal of low-energy neutrino astronomy. The prospects for detecting all flavors of neutrinos and antineutrinos from the core-collapse supernova (ccSN) in operating and forthcoming large liquid scintillation detectors (LLSD) are widely discussed now. One of proposed LLSD is Baksan Large Volume Scintillation Detector (BLVSD). This detector will be installed at the Baksan Neutrino Observatory (BNO) of the Institute for Nuclear Research, Russian Academy of Sciences, at a depth of 4800 m.w.e. Low-energy neutrino astronomy is one of the main lines of research of the BLVSD.

  5. State-of-the-Art in GPU-Based Large-Scale Volume Visualization

    KAUST Repository

    Beyer, Johanna

    2015-05-01

    This survey gives an overview of the current state of the art in GPU techniques for interactive large-scale volume visualization. Modern techniques in this field have brought about a sea change in how interactive visualization and analysis of giga-, tera- and petabytes of volume data can be enabled on GPUs. In addition to combining the parallel processing power of GPUs with out-of-core methods and data streaming, a major enabler for interactivity is making both the computational and the visualization effort proportional to the amount and resolution of data that is actually visible on screen, i.e. \\'output-sensitive\\' algorithms and system designs. This leads to recent output-sensitive approaches that are \\'ray-guided\\', \\'visualization-driven\\' or \\'display-aware\\'. In this survey, we focus on these characteristics and propose a new categorization of GPU-based large-scale volume visualization techniques based on the notions of actual output-resolution visibility and the current working set of volume bricks-the current subset of data that is minimally required to produce an output image of the desired display resolution. Furthermore, we discuss the differences and similarities of different rendering and data traversal strategies in volume rendering by putting them into a common context-the notion of address translation. For our purposes here, we view parallel (distributed) visualization using clusters as an orthogonal set of techniques that we do not discuss in detail but that can be used in conjunction with what we present in this survey. © 2015 The Eurographics Association and John Wiley & Sons Ltd.

  6. Evaluation of the programmed temperature vaporiser for large-volume injection of biological samples in gas chromatography

    NARCIS (Netherlands)

    van Hout, M.W J; de Zeeuw, R.A; Franke, J.P.; de Jong, G.J.

    1999-01-01

    The use of a programmed temperature vaporiser (PTV) with a packed liner was evaluated for the injection of large volumes (up to 100 mu l) of plasma extracts in a gas chromatograph. Solvent purity, which is essential when large volumes are injected into the GC system, was determined. Special attentio

  7. Large-N volume independence in conformal and confining gauge theories

    Energy Technology Data Exchange (ETDEWEB)

    Unsal, Mithat; /SLAC; Yaffe, Laurence G.; /Washington U., Seattle

    2010-08-26

    Consequences of large N volume independence are examined in conformal and confining gauge theories. In the large N limit, gauge theories compactified on R{sup d-k} x (S{sup 1}){sup k} are independent of the S{sup 1} radii, provided the theory has unbroken center symmetry. In particular, this implies that a large N gauge theory which, on R{sup d}, flows to an IR fixed point, retains the infinite correlation length and other scale invariant properties of the decompactified theory even when compactified on R{sup d-k} x (S{sup 1}){sup k}. In other words, finite volume effects are 1/N suppressed. In lattice formulations of vector-like theories, this implies that numerical studies to determine the boundary between confined and conformal phases may be performed on one-site lattice models. In N = 4 supersymmetric Yang-Mills theory, the center symmetry realization is a matter of choice: the theory on R{sup 4-k} x (S{sup 1}){sup k} has a moduli space which contains points with all possible realizations of center symmetry. Large N QCD with massive adjoint fermions and one or two compactified dimensions has a rich phase structure with an infinite number of phase transitions coalescing in the zero radius limit.

  8. Measuring tree height and preparation volume table using an innovative method.

    Science.gov (United States)

    Lotfalian, Majid; Nouri, Zahra; Kooch, Yahya; Zobeiri, Mahmoud

    2007-10-15

    Zarbin (Cupressus sempervirence var. horizontalis) with its unique characteristics is one of the worthiest species which can be found in the central area of Alborz in the North of Iran. Especially in the Roodbar-manjil area, Chaloos-Hassanabad valley as well as it extends from Zarringol area to Gorgan. Although the distribution areas of this species have been protected, these forests have been invaded by the villagers who use this useful wood. For this reason in the Roodbar area, trees with DBH>30 cm are extremely rare. To recognize and to be aware of the stand quantity, the current research tries to calculate the species volume table in Roodbar area, to be the basis for any calculation of the volume of stand in the region. For this purpose, trees have been sampled using the line sampling method. After estimating the form factor, Tarif table have been prepared. In this study, a new method for measuring tree height is presented, in which, instead of measuring slope distance from observer to tree (which is difficult in young conifers because of existence branches in lower height) distance between the eye level of observer to tree butt is measured. Which doing of it is easier, time of field work is decreased and accuracy of measurement and calculation is increased.

  9. A pyramid-based approach to visual exploration of a large volume of vehicle trajectory data

    Institute of Scientific and Technical Information of China (English)

    Jing SUN; Xiang LI

    2012-01-01

    Advances in positioning and wireless communicating technologies make it possible to collect large volumes of trajectory data of moving vehicles in a fast and convenient fashion.These data can be applied to traffic studies.Behind this application,a methodological issue that still requires particular attention is the way these data should be spatially visualized.Trajectory data physically consists of a large number of positioning points.With the dramatic increase of data volume,it becomes a challenge to display and explore these data.Existing commercial software often employs vector-based indexing structures to facilitate the display of a large volume of points,but their performance downgrades quickly when the number of points is very large,for example,tens of millions.In this paper,a pyramid-based approach is proposed.A pyramid method initially is invented to facilitate the display of raster images through the tradeoff between storage space and display time.A pyramid is a set of images at different levels with different resolutions.In this paper,we convert vector-based point data into raster data,and build a gridbased indexing structure in a 2D plane.Then,an image pyramid is built.Moreover,at the same level of a pyramid,image is segmented into mosaics with respect to the requirements of data storage and management.Algorithms or procedures on grid-based indexing structure,image pyramid,image segmentation,and visualization operations are given in this paper.A case study with taxi trajectory data in Shanghai is conducted.Results demonstrate that the proposed method outperforms the existing commercial software.

  10. Volume-staged radiosurgery for large arteriovenous malformations: an evolving paradigm.

    Science.gov (United States)

    Seymour, Zachary A; Sneed, Penny K; Gupta, Nalin; Lawton, Michael T; Molinaro, Annette M; Young, William; Dowd, Christopher F; Halbach, Van V; Higashida, Randall T; McDermott, Michael W

    2016-01-01

    OBJECT Large arteriovenous malformations (AVMs) remain difficult to treat, and ideal treatment parameters for volume-staged stereotactic radiosurgery (VS-SRS) are still unknown. The object of this study was to compare VS-SRS treatment outcomes for AVMs larger than 10 ml during 2 eras; Era 1 was 1992-March 2004, and Era 2 was May 2004-2008. In Era 2 the authors prospectively decreased the AVM treatment volume, increased the radiation dose per stage, and shortened the interval between stages. METHODS All cases of VS-SRS treatment for AVM performed at a single institution were retrospectively reviewed. RESULTS Of 69 patients intended for VS-SRS, 63 completed all stages. The median patient age at the first stage of VS-SRS was 34 years (range 9-68 years). The median modified radiosurgery-based AVM score (mRBAS), total AVM volume, and volume per stage in Era 1 versus Era 2 were 3.6 versus 2.7, 27.3 ml versus 18.9 ml, and 15.0 ml versus 6.8 ml, respectively. The median radiation dose per stage was 15.5 Gy in Era 1 and 17.0 Gy in Era 2, and the median clinical follow-up period in living patients was 8.6 years in Era 1 and 4.8 years in Era 2. All outcomes were measured from the first stage of VS-SRS. Near or complete obliteration was more common in Era 2 (log-rank test, p = 0.0003), with 3- and 5-year probabilities of 5% and 21%, respectively, in Era 1 compared with 24% and 68% in Era 2. Radiosurgical dose, AVM volume per stage, total AVM volume, era, compact nidus, Spetzler-Martin grade, and mRBAS were significantly associated with near or complete obliteration on univariate analysis. Dose was a strong predictor of response (Cox proportional hazards, p < 0.001, HR 6.99), with 3- and 5-year probabilities of near or complete obliteration of 5% and 16%, respectively, at a dose < 17 Gy versus 23% and 74% at a dose ≥ 17 Gy. Dose per stage, compact nidus, and total AVM volume remained significant predictors of near or complete obliteration on multivariate analysis. Seventeen

  11. The use of digital volume tomography in imaging an unusually large composite odontoma in the mandible.

    Science.gov (United States)

    Bhatavadekar, Neel B; Bouquot, Jerry E

    2009-01-01

    The odontoma is the most common of all odontogenic tumors. Digital volume tomography (DVT) provides a major advantage of decreased radiation and cost-effectiveness, as compared to a conventional computed tomography. There is no known published report utilizing this DVT analysis for assessing and localizing on odontomo. The purpose of this case report was to document the use of digital volume tomography to assess an unusually large composite odontoma in the mondible. Tomographic sections revealed expansion of the buccol cortex and occasional thinning of both the buccol and lingual cortical plates, although there was no pronounced clinically detectable cortical expansion. The sections further demonstrated enomel ond dentin in on irregular mass bearing no morphologic similority to rudimentary teeth. This case highlights the importance of early diagnosis and intervention for treating on odontoma while demonstrating the value of tomographic imaging as on aid to diagnosis.

  12. The complex aerodynamic footprint of desert locusts revealed by large-volume tomographic particle image velocimetry.

    Science.gov (United States)

    Henningsson, Per; Michaelis, Dirk; Nakata, Toshiyuki; Schanz, Daniel; Geisler, Reinhard; Schröder, Andreas; Bomphrey, Richard J

    2015-07-01

    Particle image velocimetry has been the preferred experimental technique with which to study the aerodynamics of animal flight for over a decade. In that time, hardware has become more accessible and the software has progressed from the acquisition of planes through the flow field to the reconstruction of small volumetric measurements. Until now, it has not been possible to capture large volumes that incorporate the full wavelength of the aerodynamic track left behind during a complete wingbeat cycle. Here, we use a unique apparatus to acquire the first instantaneous wake volume of a flying animal's entire wingbeat. We confirm the presence of wake deformation behind desert locusts and quantify the effect of that deformation on estimates of aerodynamic force and the efficiency of lift generation. We present previously undescribed vortex wake phenomena, including entrainment around the wing-tip vortices of a set of secondary vortices borne of Kelvin-Helmholtz instability in the shear layer behind the flapping wings.

  13. The Large-Volume Limit of a Quantum Tetrahedron is a Quantum Harmonic Oscillator

    CERN Document Server

    Schliemann, John

    2013-01-01

    It is shown that the volume operator of a quantum tetrahedron is, in the sector of large eigenvalues, accurately described by a quantum harmonic oscillator. This result relies on the fact that (i) the volume operator couples only neighboring states of its standard basis, and (ii) its matrix elements show a unique maximum as a function of internal angular momentum quantum numbers. These quantum numbers, considered as a continuous variable, are the coordinate of the oscillator describing its quadratic potential, while the corresponding derivative defines a momentum operator. We also analyze the scaling properties of the oscillator parameters as a function of the size of the tetrahedron, and the role of different angular momentum coupling schemes.

  14. A volume law for specification of linear channel storage for estimation of large floods

    Science.gov (United States)

    Zhang, Shangyou; Cordery, Ian; Sharma, Ashish

    2000-02-01

    A method of estimating large floods using a linear storage-routing approach is presented. The differences between the proposed approach and those traditionally used are (1) that the flood producing properties of basins are represented by a linear system, (2) the storage parameters of the distributed model are determined using a volume law which, unlike other storage-routing models, accounts for the distribution of storage in natural basins, and (3) the basin outflow hydrograph is determined analytically and expressed in a succinct mathematical form. The single model parameter is estimated from observed data without direct fitting, unlike most traditionally used methods. The model was tested by showing it could reproduce observed large floods on a number of basins. This paper compares the proposed approach with a traditionally used storage routing approach using observed flood data from the Hacking River basin in New South Wales, Australia. Results confirm the usefulness of the proposed approach for estimation of large floods.

  15. Specimen Preparation for Metal Matrix Composites with a High Volume Fraction of Reinforcing Particles for EBSD Analysis

    Science.gov (United States)

    Smirnov, A. S.; Belozerov, G. A.; Smirnova, E. O.; Konovalov, A. V.; Shveikin, V. P.; Muizemnek, O. Yu.

    2016-07-01

    The paper deals with a procedure of preparing a specimen surface for the EBSD analysis of a metal matrix composite (MMC) with a high volume fraction of reinforcing particles. Unlike standard procedures of preparing a specimen surface for the EBSD analysis, the proposed procedure is iterative with consecutive application of mechanical and electrochemical polishing. This procedure significantly improves the results of an indexed MMC matrix in comparison with the standard procedure of specimen preparation. The procedure was verified on a MMC with pure aluminum (99.8% Al) as the matrix, SiC particles being used as reinforcing elements. The average size of the SiC particles is 14 μm, and their volume fraction amounts to 50% of the total volume of the composite. It has been experimentally found that, for making the EBSD analysis of a material matrix near reinforcing particles, the difference in height between the particles and the matrix should not exceed 2 µm.

  16. The mechanism for large-volume fluid pumping via reversible snap-through of dielectric elastomer

    Science.gov (United States)

    Li, Zhe; Wang, Yingxi; Foo, Choon Chiang; Godaba, Hareesh; Zhu, Jian; Yap, Choon Hwai

    2017-08-01

    Giant deformation of dielectric elastomers (DEs) via electromechanical instability (or the "snap-through" phenomenon) is a promising mechanism for large-volume fluid pumping. Snap-through of a DE membrane coupled with compressible air has been previously investigated. However, the physics behind reversible snap-through of a DE diaphragm coupled with incompressible fluid for the purpose of fluid pumping has not been well investigated, and the conditions required for reversible snap-through in a hydraulic system are unknown. In this study, we have proposed a concept for large-volume fluid pumping by harnessing reversible snap-through of the dielectric elastomer. The occurrence of snap-through was theoretically modeled and experimentally verified. Both the theoretical and experimental pressure-volume curves of the DE membrane under different actuation voltages were used to design the work loop of the pump, and the theoretical work loop agreed with the experimental work loop. Furthermore, the feasibility of reversible snap-through was experimentally verified, and specific conditions were found necessary for this to occur, such as a minimum actuation voltage, an optimal range of hydraulic pressure exerted on the DE membrane and a suitable actuation frequency. Under optimal working conditions, we demonstrated a pumping volume of up to 110 ml per cycle, which was significantly larger than that without snap-through. Furthermore, we have achieved fluid pumping from a region of low pressure to another region of high pressure. Findings of this study would be useful for real world applications such as the blood pump.

  17. A Novel Technique for Endovascular Removal of Large Volume Right Atrial Tumor Thrombus

    Energy Technology Data Exchange (ETDEWEB)

    Nickel, Barbara, E-mail: nickel.ba@gmail.com [US Teleradiology and Quantum Medical Radiology Group (United States); McClure, Timothy, E-mail: tmcclure@gmail.com; Moriarty, John, E-mail: jmoriarty@mednet.ucla.edu [UCLA Medical Center, Department of Interventional Radiology (United States)

    2015-08-15

    Venous thromboembolic disease is a significant cause of morbidity and mortality, particularly in the setting of large volume pulmonary embolism. Thrombolytic therapy has been shown to be a successful treatment modality; however, its use somewhat limited due to the risk of hemorrhage and potential for distal embolization in the setting of large mobile thrombi. In patients where either thrombolysis is contraindicated or unsuccessful, and conventional therapies prove inadequate, surgical thrombectomy may be considered. We present a case of percutaneous endovascular extraction of a large mobile mass extending from the inferior vena cava into the right atrium using the Angiovac device, a venovenous bypass system designed for high-volume aspiration of undesired endovascular material. Standard endovascular methods for removal of cancer-associated thrombus, such as catheter-directed lysis, maceration, and exclusion, may prove inadequate in the setting of underlying tumor thrombus. Where conventional endovascular methods either fail or are unsuitable, endovascular thrombectomy with the Angiovac device may be a useful and safe minimally invasive alternative to open resection.

  18. Large-volume liposuction: a review of 631 consecutive cases over 12 years.

    Science.gov (United States)

    Commons, G W; Halperin, B; Chang, C C

    2001-11-01

    Since the advent of epinephrine-containing wetting solutions and sophisticated fluid management techniques, increasingly larger and larger volumes of liposuction aspirations have been reported. Unfortunately, with these larger volumes of liposuction being routinely performed, greater rates of complications have also been reported, with the worst of these resulting in deaths. In a response to the increasing concerns over the safety of large-volume liposuction, a critical review of the senior author's own series has been performed to evaluate risks and benefits and to recommend guidelines for safe and effective large-volume liposuction. A retrospective chart review was performed on 631 consecutive patients who underwent liposuction procedures of at least 3000 cc total aspirate. All procedures were performed by the same senior surgeon between January of 1986 and March of 1998. Before September of 1996, traditional liposuction techniques were used. After September of 1996, ultrasound-assisted liposuction was performed. The superwet technique of fluid management was employed for all procedures performed after 1991. The particulars of the surgical and anesthetic techniques used are reviewed in the article. Data collection included preoperative patient demographics, preoperative and postoperative weights and measurements, and preoperative and postoperative photographs. Total aspirate volumes, fluid intakes, and fluid outputs were measured, and all complications were tallied. Average follow-up was 1 year. Results showed the majority of patients to be women, aged 17 to 74 years old. Of the preoperative weights, 98.7 percent were within 50 pounds of ideal chart weight. Total aspirate volumes ranged from 3 to 17 liters, with 94.5 percent of these under 10 liters. Fluid balance measurements showed an average of 120 cc/kg positive fluid balance at the end of the procedure, with none of these patients experiencing any significant fluid balance abnormalities. Cosmetic results

  19. Incarceration of umbilical hernia: a rare complication of large volume paracentesis.

    Science.gov (United States)

    Khodarahmi, Iman; Shahid, Muhammad Usman; Contractor, Sohail

    2015-09-01

    We present two cases of umbilical hernia incarceration following large volume paracentesis (LVP) in patients with cirrhotic ascites. Both patients became symptomatic within 48 hours after the LVP. Although being rare, given the significantly higher mortality rate of cirrhotic patients undergoing emergent herniorrhaphy, this complication of LVP is potentially serious. Therefore, it is recommended that patients be examined closely for the presence of umbilical hernias before removal of ascitic fluid and an attempt should be made for external reduction of easily reducible hernias, if a hernia is present.

  20. Large Volume, Optical and Opto-Mechanical Metrology Techniques for ISIM on JWST

    Science.gov (United States)

    Hadjimichael, Theo

    2015-01-01

    The final, flight build of the Integrated Science Instrument Module (ISIM) element of the James Webb Space Telescope is the culmination of years of work across many disciplines and partners. This paper covers the large volume, ambient, optical and opto-mechanical metrology techniques used to verify the mechanical integration of the flight instruments in ISIM, including optical pupil alignment. We present an overview of ISIM's integration and test program, which is in progress, with an emphasis on alignment and optical performance verification. This work is performed at NASA Goddard Space Flight Center, in close collaboration with the European Space Agency, the Canadian Space Agency, and the Mid-Infrared Instrument European Consortium.

  1. Mass anomalous dimension of Adjoint QCD at large N from twisted volume reduction

    CERN Document Server

    Pérez, Margarita García; Keegan, Liam; Okawa, Masanori

    2015-01-01

    In this work we consider the $SU(N)$ gauge theory with two Dirac fermions in the adjoint representation, in the limit of large $N$. In this limit the infinite-volume physics of this model can be studied by means of the corresponding twisted reduced model defined on a single site lattice. Making use of this strategy we study the reduced model for various values of $N$ up to 289. By analyzing the eigenvalue distribution of the adjoint Dirac operator we test the conformality of the theory and extract the corresponding mass anomalous dimension.

  2. Durability of concrete incorporating large volumes of low-quality fly ash

    Energy Technology Data Exchange (ETDEWEB)

    Linhua Jiang; Zhenqing Liu; Yiqun Ye [Hohai University, Nanjing (China). Department of Materials Science and Engineering

    2004-08-01

    The carbonation, corrosion of steel reinforcement in concrete and corrosion resistance of concrete, incorporating large volumes of low-quality fly ash (LVLQFA), were studied. The effect of concentration of carbon dioxide used in the experiment on estimating the carbonation resistance of LVLQFA concrete were also investigated. Test results show that the LVLQFA concrete with an activator has good carbonation and corrosion resistances of steel reinforcement. The corrosion resistance of LVLQFA concrete is better than that of the control concrete. The concentration of carbon dioxide used in the experiment has considerable effect on estimating the carbonation resistance of LVLQFA concrete.

  3. Stability, Tunneling and Flux Changing de Sitter Transitions in the Large Volume String Scenario

    CERN Document Server

    de Alwis, S; Hatefi, E; Quevedo, F

    2013-01-01

    We study the non-perturbative stability of the Large Volume Scenario (LVS) of IIB string compactifications, by analysing transitions mediated by the Brown-Teitelboim (BT) brane nucleations and by Coleman De Luccia tunneling (CDL). We find that, as long as the effective field theory description holds, the LVS AdS minima are stable despite being non-supersymmetric. This opens the possibility of having a CFT dual. Metastable de Sitter vacua behave differently depending on the uplifting mechanism. We find explicit expressions for the different decay rates in terms of exponentials of the volume. Among the transitions of dS to dS those with increasing volume and decreasing vacuum energy are preferred, though dS decays to AdS (big-crunch sinks) have higher probability. Transitions via the CDL mechanism to decompactification are exponentially suppressed compared to these. The BT decays correspond to flux/D3 brane transitions mediated by the nucleation of D5/NS5 branes. We compare our results with previous analysis fo...

  4. Hybrid Parallelism for Volume Rendering on Large, Multi- and Many-core Systems

    Energy Technology Data Exchange (ETDEWEB)

    Howison, Mark; Bethel, E. Wes; Childs, Hank

    2011-01-01

    With the computing industry trending towards multi- and many-core processors, we study how a standard visualization algorithm, ray-casting volume rendering, can benefit from a hybrid parallelism approach. Hybrid parallelism provides the best of both worlds: using distributed-memory parallelism across a large numbers of nodes increases available FLOPs and memory, while exploiting shared-memory parallelism among the cores within each node ensures that each node performs its portion of the larger calculation as efficiently as possible. We demonstrate results from weak and strong scaling studies, at levels of concurrency ranging up to 216,000, and with datasets as large as 12.2 trillion cells. The greatest benefit from hybrid parallelism lies in the communication portion of the algorithm, the dominant cost at higher levels of concurrency. We show that reducing the number of participants with a hybrid approach significantly improves performance.

  5. First large volume characterization of the QIE10/11 custom front-end integrated circuits

    Science.gov (United States)

    Hare, D.; Baumbaugh, A.; Dal Monte, L.; Freeman, J.; Hirschauer, J.; Hughes, E.; Roy, T.; Whitbeck, A.; Yumiceva, F.; Zimmerman, T.

    2016-02-01

    The CMS experiment at the CERN Large Hadron Collider (LHC) will upgrade the photon detection and readout systems of its barrel and endcap hadron calorimeters (HCAL) through the second long shutdown of the LHC in 2018. A central feature of this upgrade is the development of two new versions of the QIE (Charge Integrator and Encoder), a Fermilab-designed custom ASIC for measurement of charge from detectors in high-rate environments. These most recent additions to the QIE family feature 17-bits of dynamic range with 1% digitization precision for high charge and a time-to-digital converter (TDC) with half nanosecond resolution all with 16 bits of readout per bunch crossing. For the first time, the CMS experiment has produced and characterized in great detail a large volume of chips. The characteristics and performance of the new QIE and their related chip-to-chip variations as measured in a sample of 10,000 chips is described.

  6. MPI-hybrid Parallelism for Volume Rendering on Large, Multi-core Systems

    Energy Technology Data Exchange (ETDEWEB)

    Howison, Mark; Bethel, E. Wes; Childs, Hank

    2010-03-20

    This work studies the performance and scalability characteristics of"hybrid'" parallel programming and execution as applied to raycasting volume rendering -- a staple visualization algorithm -- on a large, multi-core platform. Historically, the Message Passing Interface (MPI) has become the de-facto standard for parallel programming and execution on modern parallel systems. As the computing industry trends towards multi-core processors, with four- and six-core chips common today and 128-core chips coming soon, we wish to better understand how algorithmic and parallel programming choices impact performance and scalability on large, distributed-memory multi-core systems. Our findings indicate that the hybrid-parallel implementation, at levels of concurrency ranging from 1,728 to 216,000, performs better, uses a smaller absolute memory footprint, and consumes less communication bandwidth than the traditional, MPI-only implementation.

  7. Hybrid Parallelism for Volume Rendering on Large, Multi-core Systems

    Science.gov (United States)

    Howison, M.; Bethel, E. W.; Childs, H.

    2011-10-01

    This work studies the performance and scalability characteristics of "hybrid" parallel programming and execution as applied to raycasting volume rendering - a staple visualization algorithm - on a large, multi-core platform. Historically, the Message Passing Interface (MPI) has become the de-facto standard for parallel programming and execution on modern parallel systems. As the computing industry trends towards multi-core processors, with four- and six-core chips common today, as well as processors capable of running hundreds of concurrent threads (GPUs), we wish to better understand how algorithmic and parallel programming choices impact performance and scalability on large, distributed-memory multi-core systems. Our findings indicate that the hybrid-parallel implementation, at levels of concurrency ranging from 1,728 to 216,000, performs better, uses a smaller absolute memory footprint, and consumes less communication bandwidth than the traditional, MPI-only implementation.

  8. Clinical Trial of 1000 Subjects Randomized to 5 Low-Volume Bowel Preparations for Colonoscopy and Their Acceptance of Split-Dose Bowel Preparations.

    Science.gov (United States)

    Gerard, David P; Foster, Diane B; Holden, John L; Kang, Jieun; Raiser, Manfred W

    2017-07-01

    We assessed the efficacy and tolerability of 5 low-volume bowel preparations for colonoscopy. We performed an investigator-blinded, randomized trial of 5 bowel preparations: 64 ounces of Gatorade and 306 or 357 g of PEG, both given the day prior; Gatorade and 306 g PEG, 2 L PEG-electrolyte solution with ascorbic acid, and sulfate solution, all 3 given as a split dose. One thousand outpatients consumed their preparation before a morning colonoscopy. The primary endpoint was colon cleanliness assessed by the Chicago Bowel Preparation Scale (BPS). Tolerability was assessed using a subject questionnaire. Another primary endpoint was patient acceptance of a split-dose bowel preparation assessed using a subject questionnaire. No statistically significant differences in the modified Chicago BPS were found among Gatorade and 357 g of PEG given as a day-prior dose and the 3 split-dose arms with 98.5% of colons cleansed adequately. The Gatorade and 357 g of PEG had significantly lower Chicago BPS fluid scores and Chicago BPS total scores (indicating dryer colons that required more irrigation) than the 3 split-dose arms. The Gatorade and PEG preparations were better tolerated. Many subjects are unwilling to consume a split-dose preparation and the majority of subjects would prefer a day-prior preparation with this preference highly dependent on the type of preparation they just consumed. The cleanliness of the colons was not significantly different among the 3 split-dose preparations. Day-prior dosing of Gatorade and 357 g of PEG allowed the mucosa to be visualized as well as did the split-dose preparations.

  9. Generation of Diffuse Large Volume Plasma by an Ionization Wave from a Plasma Jet

    Science.gov (United States)

    Laroussi, Mounir; Razavi, Hamid

    2015-09-01

    Low temperature plasma jets emitted in ambient air are the product of fast ionization waves that are guided within a channel of a gas flow, such as helium. This guided ionization wave can be transmitted through a dielectric material and under some conditions can ignite a discharge behind the dielectric material. Here we present a novel way to produce large volume diffuse low pressure plasma inside a Pyrex chamber that does not have any electrodes or electrical energy directly applied to it. The diffuse plasma is ignited inside the chamber by a plasma jet located externally to the chamber and that is physically and electrically unconnected to the chamber. Instead, the plasma jet is just brought in close proximity to the external wall/surface of the chamber or to a dielectric tubing connected to the chamber. The plasma thus generated is diffuse, large volume and with physical and chemical characteristics that are different than the external plasma jet that ignited it. So by using a plasma jet we are able to ``remotely'' ignite volumetric plasma under controlled conditions. This novel method of ``remote'' generation of a low pressure, low temperature diffuse plasma can be useful for various applications including material processing and biomedicine.

  10. Colloids Versus Albumin in Large Volume Paracentesis to Prevent Circulatory Dysfunction: Evidence-based Case Report.

    Science.gov (United States)

    Widjaja, Felix F; Khairan, Paramita; Kamelia, Telly; Hasan, Irsan

    2016-04-01

    Large volume paracentesis may cause paracentesis induced circulatory dysfunction (PICD). Albumin is recommended to prevent this abnormality. Meanwhile, the price of albumin is too expensive and there should be another alternative that may prevent PICD. This report aimed to compare albumin to colloids in preventing PICD. Search strategy was done using PubMed, Scopus, Proquest, dan Academic Health Complete from EBSCO with keywords of "ascites", "albumin", "colloid", "dextran", "hydroxyethyl starch", "gelatin", and "paracentesis induced circulatory dysfunction". Articles was limited to randomized clinical trial and meta-analysis with clinical question of "In hepatic cirrhotic patient undergone large volume paracentesis, whether colloids were similar to albumin to prevent PICD". We found one meta-analysis and four randomized clinical trials (RCT). A meta analysis showed that albumin was still superior of which odds ratio 0.34 (0.23-0.51). Three RCTs showed the same results and one RCT showed albumin was not superior than colloids. We conclude that colloids could not constitute albumin to prevent PICD, but colloids still have a role in patient who undergone paracentesis less than five liters.

  11. A Repetitive Nanosecond Pulse Source for Generation of Large Volume Streamer Discharge

    Institute of Scientific and Technical Information of China (English)

    TAO Fengbo; ZHANG Qiaogen; GAO Bo; WANG Hu; LI Zhou

    2008-01-01

    Using a unipolar pulse with the rise time and the pulse duration in the order of microsecond as the primary pulse,a nanosecond pulse with the repetitive frequency of several kilohertz is generated by a spark gap switch.By varying both the inter-pulse duration and the pulse frequency,the voltage recovery rate of the spark gap switch is investigated at different working conditions such as the gas pressure,the gas composition as well as the bias voltage.The results reveal that either increase in gas pressure or addition of SF6 to the air can increase the voltage recovery rate.The effect of gas composition on the voltage recovery rate is discussed based on the transferring and distribution of the residual space charges.The repetitive nanosecond pulse source is also applied to the generation of large volume,and the discharge currents are measured to investigate the effect of pulse repetition rate on the large volume streamer discharge.

  12. Characterization of Large Volume 3.5 x 8 inches LaBr3:Ce Detectors

    CERN Document Server

    Giaz, A; Riboldi, S; Camera, F; Blasi, N; Boiano, C; Bracco, A; Brambilla, S; Ceruti, S; Coelli, S; Crespi, F C L; Csatlòs, M; Frega, S; Gulyàs, J; Krasznahorkay, A; Lodetti, S; Million, B; Owens, A; Quarati, F; Stuhl, L; Wieland, O

    2013-01-01

    The properties of large volume cylindrical 3.5 x 8 inches (89 mm x 203 mm) LaBr3:Ce scintillation detectors coupled to the Hamamatsu R10233-100SEL photo-multiplier tube were investigated. These crystals are among the largest ones ever produced and still need to be fully characterized to determine how these detectors can be utilized and in which applications. We tested the detectors using monochromatic gamma-ray sources and in-beam reactions producing gamma rays up to 22.6 MeV; we acquired PMT signal pulses and calculated detector energy resolution and response linearity as a function of gamma-ray energy. Two different voltage dividers were coupled to the Hamamatsu R10233-100SEL PMT: the Hamamatsu E1198-26, based on straightforward resistive network design, and the LABRVD, specifically designed for our large volume LaBr3:Ce scintillation detectors, which also includes active semiconductor devices. Because of the extremely high light yield of LaBr3:Ce crystals we observed that, depending on the choice of PMT, v...

  13. Study of laser induced thermo-acoustic signals in a large ice volume

    Energy Technology Data Exchange (ETDEWEB)

    Bissok, Martin; Laihem, Karim; Meures, Thomas; Paul, Larissa; Wiebusch, Christopher; Zierke, Simon [III. Physikalisches Institut, RWTH Aachen (Germany)

    2010-07-01

    A goal for next generation neutrino-telescopes is the exploration of the extremely high energy region (>EeV). Expected neutrino event rates in this energy range are low (<1 event/km{sup 3}/year) and therefore a detector volume which is increased by more than one order of magnitude compared to IceCube is desireable. A possible approach to achieve such an increase in a cost-effective way is the acoustic detection of neutrinos, based on the principle of thermoacoustic signal generation in neutrino-induced hadronic cascades. The Aachen Acoustic Laboratory (AAL) provides the means to study the thermoacoustic effect in a controlled environment. It consists of a large water-filled tank inside a cooling container. The freezing process is controlled and a large volume of bubble-free clear ice({proportional_to}3m{sup 3}) is produced. Thermoacoustic signals are generated by a pulsed Nd:YAG laser with an energy of up to 55 mJ/pulse. The acoustic signals are recorded by an array of 19 piezo-based sensors embedded in the ice. In this talk we give a description of this test experiment and present results from an initial freezing period.

  14. Large-volume optical coherence tomography with real-time correction of geometric distortion artifacts

    CERN Document Server

    Van der Jeught, Sam; Bradu, Adrian; Podoleanu, Adrian Gh; Dirckx, Joris J J

    2012-01-01

    Large-volume optical coherence tomography (OCT)-setups employ scanning mirrors and suffer from non-linear geometric distortion artifacts in which the degree of distortion is determined by the maximum angles over which the mirrors rotate. In this chapter, we describe a straightforward approach to correct for these distortion artifacts, creating an alternative to previously reported ray-tracing schemes that are unable to apply these corrections in real-time. By implementing the proposed 3D recalibration algorithm on the graphics card of a standard computer, this feature can be applied in real-time. We validate the accuracy of the technique using OCT measurements of a highly curved object within a large imaging volume of 12.35 x 10.13 x 2.36 mm^3. The resulting 3D object shape measurements are compared against high-resolution and aberration-free optical profilometry measurements. Maintaining an optical resolution of <10 micron within the sample, both axially and transversally, we realized a real-time, high-re...

  15. Large-volume flux closure during plasmoid-mediated reconnection in coaxial helicity injection

    Science.gov (United States)

    Ebrahimi, F.; Raman, R.

    2016-04-01

    A large-volume flux closure during transient coaxial helicity injection (CHI) in NSTX-U is demonstrated through resistive magnetohydrodynamics (MHD) simulations. Several major improvements, including the improved positioning of the divertor poloidal field coils, are projected to improve the CHI start-up phase in NSTX-U. Simulations in the NSTX-U configuration with constant in time coil currents show that with strong flux shaping the injected open field lines (injector flux) rapidly reconnect and form large volume of closed flux surfaces. This is achieved by driving parallel current in the injector flux coil and oppositely directed currents in the flux shaping coils to form a narrow injector flux footprint and push the injector flux into the vessel. As the helicity and plasma are injected into the device, the oppositely directed field lines in the injector region are forced to reconnect through a local Sweet-Parker type reconnection, or to spontaneously reconnect when the elongated current sheet becomes MHD unstable to form plasmoids. In these simulations for the first time, it is found that the closed flux is over 70% of the initial injector flux used to initiate the discharge. These results could work well for the application of transient CHI in devices that employ super conducting coils to generate and sustain the plasma equilibrium.

  16. Large range rotation distortion measurement for remote sensing images based on volume holographic optical correlator

    Science.gov (United States)

    Zheng, Tianxiang; Cao, Liangcai; Zhao, Tian; He, Qingsheng; Jin, Guofan

    2012-10-01

    Volume holographic optical correlator can compute the correlation results between images at a super-high speed. In the application of remote imaging processing such as scene matching, 6,000 template images have been angularly multiplexed in the photorefractive crystal and the 6,000 parallel processing channels are achieved. In order to detect the correlation pattern of images precisely and distinguishingly, an on-off pixel inverted technology of images is proposed. It can fully use the CCD's linear range for detection and expand the normalized correlation value differences as the target image rotates. Due to the natural characteristics of the remote sensing images, the statistical formulas between the rotation distortions and the correlation results can be estimated. The rotation distortion components can be estimated by curve fitting method with the data of correlation results. The intensities of the correlation spots are related to the distortion between the two images. The rotation distortion could be derived from the intensities in the post processing procedure. With 18 rotations of the input image and sending them into the volume holographic system, the detection of the rotation variation in the range of 180° can be fulfilled. So the large range rotation distortion detection is firstly realized. It offers a fast, large range rotation measurement method for image distortions.

  17. VolumeExplorer: Roaming Large Volumes to Couple Visualization and Data Processing for Oil and Gas Exploration

    OpenAIRE

    2005-01-01

    http://ieeexplore.ieee.org/; In this paper, we present a volume roaming system dedicated to oil and gas exploration. Our system combines probe-based volume rendering with data processing and computing. The daily oil production and the estimation of the world proven-reserves directly affect the barrel price and have a strong impact on the economy. Among others, production and correct estimation are linked to the accuracy of the subsurface model used for predicting oil reservoirs shape and size...

  18. Acid/base bifunctional carbonaceous nanomaterial with large surface area: Preparation, characterization, and adsorption properties for cationic and anionic compounds

    Energy Technology Data Exchange (ETDEWEB)

    Li, Kai; Ma, Chun–Fang; Ling, Yuan; Li, Meng [Department of Chemistry, Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074 (China); Gao, Qiang, E-mail: gaoqiang@cug.edu.cn [Department of Chemistry, Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074 (China); Engineering Research Center of Nano-Geo Materials of Ministry of Education, China University of Geosciences, Wuhan 430074 (China); Luo, Wen–Jun, E-mail: heartnohome@yahoo.com.cn [Department of Chemistry, Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074 (China)

    2015-07-15

    Nanostructured carbonaceous materials are extremely important in the nano field, yet developing simple, mild, and “green” methods that can make such materials possess large surface area and rich functional groups on their surfaces still remains a considerable challenge. Herein, a one-pot and environment-friendly method, i.e., thermal treatment (180 °C; 18 h) of water mixed with glucose and chitosan (CTS), has been proposed. The resultant carbonaceous nanomaterials were characterized by field emitting scanning electron microscope, N{sub 2} adsorption/desorption, Fourier transform infrared spectroscope, X-ray photoelectron spectroscopy, and zeta-potential analysis. It was found that, in contrast to the conventional hydrothermally carbonized product from pure glucose, with low surface area (9.3 m{sup 2} g{sup −1}) and pore volume (0.016 cm{sup 3} g{sup −1}), the CTS-added carbonaceous products showed satisfactory textural parameters (surface area and pore volume up to 254 m{sup 2} g{sup −1} and 0.701 cm{sup 3} g{sup −1}, respectively). Moreover, it was also interestingly found that these CTS-added carbonaceous products possessed both acidic (–COOH) and basic (–NH{sub 2}) groups on their surfaces. Taking the advantages of large surface area and –COOH/–NH{sub 2} bifunctional surface, the carbonaceous nanomaterials exhibited excellent performance for adsorptions of cationic compound (i.e., methylene blue) at pH 10 and anionic compound (i.e., acid red 18) at pH 2, respectively. This work not only provides a simple and green route to prepare acid/base bifunctional carbonaceous nanomaterials with large surface area but also well demonstrates their potential for application in adsorption. - Highlights: • A simple and green method was proposed to prepare carbon nanomaterials. • The carbon product showed acid/base bifunctional surface with large surface area. • The carbon material could efficiently adsorb both cationic and anionic compounds.

  19. Pathways of deep cyclones associated with large volume changes (LVCs) and major Baltic inflows (MBIs)

    Science.gov (United States)

    Lehmann, Andreas; Höflich, Katharina; Post, Piia; Myrberg, Kai

    2017-03-01

    Large volume changes (LVCs) and major Baltic inflows (MBIs) are essential processes for the water exchange and renewal of the stagnant water in the Baltic Sea deep basins. These strong inflows are known to be forced by persistent westerly wind conditions. In this study, MBIs are considered as subset of LVCs transporting with the large water volume a big amount of highly saline and oxygenated water into the Baltic Sea. Since the early 1980s the frequency of MBIs has dropped drastically from 5 to 7 events to only one inflow per decade, and long lasting periods without MBIs became the usual state. Only in January 1993, 2003 and December 2014 MBIs occurred that were able to interrupt the stagnation periods in the deep basins of the Baltic Sea. However, in spite of the decreasing frequency of MBIs, there is no obvious decrease of LVCs. The Landsort sea level is known to reflect the mean sea level of the Baltic Sea very well, and hence LVCs have been calculated for the period 1887-2015 filtering daily time series of Landsort sea surface elevation anomalies. The cases with local minimum and maximum difference resulting in at least 60 km3 of water volume change excluding the volume change due to runoff have been chosen for a closer study (1948-2013) of characteristic pathways of deep cyclones. The average duration of LVCs is about 40 days. During this time, 5-6 deep cyclones move along characteristic storm tracks. Furthermore, MBIs are characterized by even higher cyclonic activity compared to average LVCs. We obtained four main routes of deep cyclones which were associated with LVCs, but also with the climatology. One is approaching from the west at about 56-60°N, passing the northern North Sea, northern Denmark, Sweden and the Island of Gotland. A second broad corridor of frequent cyclone pathways enters the study area north of Scotland between 60 and 66°N turning north-eastwards along the northern coast of Scandinavia. This branch bifurcates into smaller routes. One

  20. Random forest classification of large volume structures for visuo-haptic rendering in CT images

    Science.gov (United States)

    Mastmeyer, Andre; Fortmeier, Dirk; Handels, Heinz

    2016-03-01

    For patient-specific voxel-based visuo-haptic rendering of CT scans of the liver area, the fully automatic segmentation of large volume structures such as skin, soft tissue, lungs and intestine (risk structures) is important. Using a machine learning based approach, several existing segmentations from 10 segmented gold-standard patients are learned by random decision forests individually and collectively. The core of this paper is feature selection and the application of the learned classifiers to a new patient data set. In a leave-some-out cross-validation, the obtained full volume segmentations are compared to the gold-standard segmentations of the untrained patients. The proposed classifiers use a multi-dimensional feature space to estimate the hidden truth, instead of relying on clinical standard threshold and connectivity based methods. The result of our efficient whole-body section classification are multi-label maps with the considered tissues. For visuo-haptic simulation, other small volume structures would have to be segmented additionally. We also take a look into these structures (liver vessels). For an experimental leave-some-out study consisting of 10 patients, the proposed method performs much more efficiently compared to state of the art methods. In two variants of leave-some-out experiments we obtain best mean DICE ratios of 0.79, 0.97, 0.63 and 0.83 for skin, soft tissue, hard bone and risk structures. Liver structures are segmented with DICE 0.93 for the liver, 0.43 for blood vessels and 0.39 for bile vessels.

  1. Volume changes of extremely large and giant intracranial aneurysms after treatment with flow diverter stents

    Energy Technology Data Exchange (ETDEWEB)

    Carneiro, Angelo; Byrne, James V. [ohn Radcliffe Hospital, Oxford Neurovascular and Neuroradiology Research Unit, Nuffield Department of Surgical Sciences, Oxford (United Kingdom); Rane, Neil; Kueker, Wilhelm; Cellerini, Martino; Corkill, Rufus [John Radcliffe Hospital, Department of Neuroradiology, Oxford (United Kingdom)

    2014-01-15

    This study assessed volume changes of unruptured large and giant aneurysms (greatest diameter >20 mm) after treatment with flow diverter (FD) stents. Clinical audit of the cases treated in a single institution, over a 5-year period. Demographic and clinical data were retrospectively collected from the hospital records. Aneurysm volumes were measured by manual outlining at sequential slices using computerised tomography (CT) or magnetic resonance (MR) angiography data. The audit included eight patients (seven females) with eight aneurysms. Four aneurysms involved the cavernous segment of the internal carotid artery (ICA), three the supraclinoid ICA and one the basilar artery. Seven patients presented with signs and symptoms of mass effect and one with seizures. All but one aneurysm was treated with a single FD stent; six aneurysms were also coiled (either before or simultaneously with FD placement). Minimum follow-up time was 6 months (mean 20 months). At follow-up, three aneurysms decreased in size, three were unchanged and two increased. Both aneurysms that increased in size showed persistent endosaccular flow at follow-up MR; in one case, failure was attributed to suboptimal position of the stent; in the other case, it was attributed to persistence of a side branch originating from the aneurysm (similar to the endoleak phenomenon of aortic aneurysms). At follow-up, five aneurysms were completely occluded; none of these increased in volume. Complete occlusion of the aneurysms leads, in most cases, to its shrinkage. In cases of late aneurysm growth or regrowth, consideration should be given to possible endoleak as the cause. (orig.)

  2. A large volume uniform plasma generator for the experiments of electromagnetic wave propagation in plasma

    Energy Technology Data Exchange (ETDEWEB)

    Yang Min; Li Xiaoping; Xie Kai; Liu Donglin [School of Electronical and Mechanical Engineering, Xidian University, Xi' an Shaanxi 710071 (China); Liu Yanming [School of Telecommunications Engineering, Xidian University, Xi' an Shaanxi 710071 (China)

    2013-01-15

    A large volume uniform plasma generator is proposed for the experiments of electromagnetic (EM) wave propagation in plasma, to reproduce a 'black out' phenomenon with long duration in an environment of the ordinary laboratory. The plasma generator achieves a controllable approximate uniform plasma in volume of 260 mm Multiplication-Sign 260 mm Multiplication-Sign 180 mm without the magnetic confinement. The plasma is produced by the glow discharge, and the special discharge structure is built to bring a steady approximate uniform plasma environment in the electromagnetic wave propagation path without any other barriers. In addition, the electron density and luminosity distributions of plasma under different discharge conditions were diagnosed and experimentally investigated. Both the electron density and the plasma uniformity are directly proportional to the input power and in roughly reverse proportion to the gas pressure in the chamber. Furthermore, the experiments of electromagnetic wave propagation in plasma are conducted in this plasma generator. Blackout phenomena at GPS signal are observed under this system and the measured attenuation curve is of reasonable agreement with the theoretical one, which suggests the effectiveness of the proposed method.

  3. A large volume cell for in situ neutron diffraction studies of hydrothermal crystallizations

    Science.gov (United States)

    Xia, Fang; Qian, Gujie; Brugger, Joël; Studer, Andrew; Olsen, Scott; Pring, Allan

    2010-10-01

    A hydrothermal cell with 320 ml internal volume has been designed and constructed for in situ neutron diffraction studies of hydrothermal crystallizations. The cell design adopts a dumbbell configuration assembled with standard commercial stainless steel components and a zero-scattering Ti-Zr alloy sample compartment. The fluid movement and heat transfer are simply driven by natural convection due to the natural temperature gradient along the fluid path, so that the temperature at the sample compartment can be stably sustained by heating the fluid in the bottom fluid reservoir. The cell can operate at temperatures up to 300 °C and pressures up to 90 bars and is suitable for studying reactions requiring a large volume of hydrothermal fluid to damp out the negative effect from the change of fluid composition during the course of the reactions. The capability of the cell was demonstrated by a hydrothermal phase transformation investigation from leucite (KAlSi2O6) to analcime (NaAlSi2O6ṡH2O) at 210 °C on the high intensity powder diffractometer Wombat in ANSTO. The kinetics of the transformation has been resolved by collecting diffraction patterns every 10 min followed by Rietveld quantitative phase analysis. The classical Avrami/Arrhenius analysis gives an activation energy of 82.3±1.1 kJ mol-1. Estimations of the reaction rate under natural environments by extrapolations agree well with petrological observations.

  4. Evaluation of Large Volume SrI2(Eu) Scintillator Detectors

    Energy Technology Data Exchange (ETDEWEB)

    Sturm, B W; Cherepy, N J; Drury, O B; Thelin, P A; Fisher, S E; Magyar, A F; Payne, S A; Burger, A; Boatner, L A; Ramey, J O; Shah, K S; Hawrami, R

    2010-11-18

    There is an ever increasing demand for gamma-ray detectors which can achieve good energy resolution, high detection efficiency, and room-temperature operation. We are working to address each of these requirements through the development of large volume SrI{sub 2}(Eu) scintillator detectors. In this work, we have evaluated a variety of SrI{sub 2} crystals with volumes >10 cm{sup 3}. The goal of this research was to examine the causes of energy resolution degradation for larger detectors and to determine what can be done to mitigate these effects. Testing both packaged and unpackaged detectors, we have consistently achieved better resolution with the packaged detectors. Using a collimated gamma-ray source, it was determined that better energy resolution for the packaged detectors is correlated with better light collection uniformity. A number of packaged detectors were fabricated and tested and the best spectroscopic performance was achieved for a 3% Eu doped crystal with an energy resolution of 2.93% FWHM at 662keV. Simulations of SrI{sub 2}(Eu) crystals were also performed to better understand the light transport physics in scintillators and are reported. This study has important implications for the development of SrI{sub 2}(Eu) detectors for national security purposes.

  5. Floating substructure flexibility of large-volume 10MW offshore wind turbine platforms in dynamic calculations

    Science.gov (United States)

    Borg, Michael; Melchior Hansen, Anders; Bredmose, Henrik

    2016-09-01

    Designing floating substructures for the next generation of 10MW and larger wind turbines has introduced new challenges in capturing relevant physical effects in dynamic simulation tools. In achieving technically and economically optimal floating substructures, structural flexibility may increase to the extent that it becomes relevant to include in addition to the standard rigid body substructure modes which are typically described through linear radiation-diffraction theory. This paper describes a method for the inclusion of substructural flexibility in aero-hydro-servo-elastic dynamic simulations for large-volume substructures, including wave-structure interactions, to form the basis of deriving sectional loads and stresses within the substructure. The method is applied to a case study to illustrate the implementation and relevance. It is found that the flexible mode is significantly excited in an extreme event, indicating an increase in predicted substructure internal loads.

  6. Direct Numerical Simulation of Reionization in Large Cosmological Volumes I: Numerical Methods and Tests

    CERN Document Server

    Norman, Michael L; So, Geoffrey C; Harkness, Robsert P

    2013-01-01

    We describe an extension of the {\\em Enzo} code to enable the direct numerical simulation of inhomogeneous reionization in large cosmological volumes. By direct we mean all dynamical, radiative, and chemical properties are solved self-consistently on the same mesh, as opposed to a postprocessing approach which coarse-grains the radiative transfer. We do, however, employ a simple subgrid model for star formation, which we calibrate to observations. The numerical method presented is a modification of an earlier method presented in Reynolds et al. Radiation transport is done in the grey flux-limited diffusion (FLD) approximation, which is solved by implicit time integration split off from the gas energy and ionization equations, which are solved separately. This results in a faster and more robust scheme for cosmological applications compared to the earlier method. The FLD equation is solved using the {\\em hypre} optimally scalable geometric multigrid solver from LLNL. By treating the ionizing radiation as a gri...

  7. The use of Enterprise Service Bus to transfer large volumes of data

    Directory of Open Access Journals (Sweden)

    Tomasz Górski

    2014-04-01

    Full Text Available The paper presents an application of Enterprise Service Bus (ESB to handle transfer of large volumes of data between IT systems. The use of ESB may affect the reduction of operating costs of the public entity minimizing the number of connections between systems, shortening the time of integration with external systems and increasing the reusability of software written. The design of integration was done according to the ‘1+5’ architectural views model adjusted to the integration solutions description. The previously proposed UML profile UML Profile for Integration Platform has been used. We present the solution, on a specific case study of Agricultural and Food Quality Inspection (AFQI (www.ijhars.gov.pl, showing how fast data can be transferred electronically using an ESB. Finally, benefits of the solution were analysed in the context of the reduced time of data transfer.

  8. Determination of 137Cs in large volume seawater using Cu-hexacyanoferrate cartridge filters

    Science.gov (United States)

    Visetpotjanakit, S.; Tumnoi, Y.

    2017-06-01

    A simple method to determine 137Cs in seawater has been developed based on the use of a Cu-hexacyanoferrate scavenger. The Cu-hexacyanoferrate supported on cotton wound cartridge filter was used to absorb 137Cs from seawater by passing large volumes over the cartridge filters with flowrate of 240 L hr-1. Results from the Cu-hexacyanoferrate method were proved acceptable for accuracy with bias below ± 20 % i.e. - 9.16 to + 18.55 % when compared with the traditional ammonium molybdophosphate pre-concentration method. This developed method is cost-effective and less time consuming. In addition it can be easily performed at sampling fields.

  9. Studies on plasma production in a large volume system using multiple compact ECR plasma sources

    Science.gov (United States)

    Tarey, R. D.; Ganguli, A.; Sahu, D.; Narayanan, R.; Arora, N.

    2017-01-01

    This paper presents a scheme for large volume plasma production using multiple highly portable compact ECR plasma sources (CEPS) (Ganguli et al 2016 Plasma Source Sci. Technol. 25 025026). The large volume plasma system (LVPS) described in the paper is a scalable, cylindrical vessel of diameter  ≈1 m, consisting of source and spacer sections with multiple CEPS mounted symmetrically on the periphery of the source sections. Scaling is achieved by altering the number of source sections/the number of sources in a source section or changing the number of spacer sections for adjusting the spacing between the source sections. A series of plasma characterization experiments using argon gas were conducted on the LVPS under different configurations of CEPS, source and spacer sections, for an operating pressure in the range 0.5-20 mTorr, and a microwave power level in the range 400-500 W per source. Using Langmuir probes (LP), it was possible to show that the plasma density (~1  -  2  ×  1011 cm-3) remains fairly uniform inside the system and decreases marginally close to the chamber wall, and this uniformity increases with an increase in the number of sources. It was seen that a warm electron population (60-80 eV) is always present and is about 0.1% of the bulk plasma density. The mechanism of plasma production is discussed in light of the results obtained for a single CEPS (Ganguli et al 2016 Plasma Source Sci. Technol. 25 025026).

  10. Large-volume liposuction and prevention of type 2 diabetes: a preliminary report.

    Science.gov (United States)

    Narsete, Thomas; Narsete, Michele; Buckspan, Randy; Ersek, Robert

    2012-04-01

    This report presents a preliminary study investigating the effects of large-volume liposuction on the parameters that determine type 2 diabetes. The study enrolled 31 patients with a body mass index (BMI) exceeding 30 kg/m(2) over a 1-year period. All the liposuction procedures were performed with the patient under local anesthesia using ketamine/valium sedation. Pre- and postoperative blood pressure, fasting glucose, glycosylated hemoglobin (HbA1C), weight, and BMI were evaluated for 16 of the 30 patients who returned for a follow-up visit 3 to 12 months postoperatively. The average aspirate was 8,455 ml without dermolipectomy and 5,795 ml with dermolipectomy. The data reveal a trend of improvement in blood sugar levels associated with weight loss that helps the patients. The average blood sugar level dropped 18% in our return patients, and the average weight loss was 9.2%. The average drop in BMI was 6.2%, and HbA1C showed a decrease of 2.3%. The patients with the best weight loss had the best reduction in blood sugar level and blood pressure. No transfers to the hospital and no thromboebolism occurred for any of the 31 patients. One dehiscence, two wound infections, and three seromas were reported. The authors hypothesize that large-volume liposuction in their series may have motivated some to diet, which could be explored in a larger series with control groups. Liposuction alone did not improve obesity but helped to motivate some of the patients to lose weight. These patients had the best results.

  11. Building high-performance system for processing a daily large volume of Chinese satellites imagery

    Science.gov (United States)

    Deng, Huawu; Huang, Shicun; Wang, Qi; Pan, Zhiqiang; Xin, Yubin

    2014-10-01

    The number of Earth observation satellites from China increases dramatically recently and those satellites are acquiring a large volume of imagery daily. As the main portal of image processing and distribution from those Chinese satellites, the China Centre for Resources Satellite Data and Application (CRESDA) has been working with PCI Geomatics during the last three years to solve two issues in this regard: processing the large volume of data (about 1,500 scenes or 1 TB per day) in a timely manner and generating geometrically accurate orthorectified products. After three-year research and development, a high performance system has been built and successfully delivered. The high performance system has a service oriented architecture and can be deployed to a cluster of computers that may be configured with high end computing power. The high performance is gained through, first, making image processing algorithms into parallel computing by using high performance graphic processing unit (GPU) cards and multiple cores from multiple CPUs, and, second, distributing processing tasks to a cluster of computing nodes. While achieving up to thirty (and even more) times faster in performance compared with the traditional practice, a particular methodology was developed to improve the geometric accuracy of images acquired from Chinese satellites (including HJ-1 A/B, ZY-1-02C, ZY-3, GF-1, etc.). The methodology consists of fully automatic collection of dense ground control points (GCP) from various resources and then application of those points to improve the photogrammetric model of the images. The delivered system is up running at CRESDA for pre-operational production and has been and is generating good return on investment by eliminating a great amount of manual labor and increasing more than ten times of data throughput daily with fewer operators. Future work, such as development of more performance-optimized algorithms, robust image matching methods and application

  12. Volume Visualization and Compositing on Large-Scale Displays Using Handheld Touchscreen Interaction

    KAUST Repository

    Gastelum, Cristhopper Jacobo Armenta

    2011-07-27

    Advances in the physical sciences have progressively delivered ever increasing, already extremely large data sets to be analyzed. High performance volume rendering has become critical to the scientists for a better understanding of the massive amounts of data to be visualized. Cluster based rendering systems have become the base line to achieve the power and flexibility required to perform such task. Furthermore, display arrays have become the most suitable solution to display these data sets at their natural size and resolution which can be critical for human perception and evaluation. The work in this thesis aims at improving the scalability and usability of volume rendering systems that target visualization on display arrays. The first part deals with improving the performance by introducing the implementations of two parallel compositing algorithms for volume rendering: direct send and binary swap. The High quality Volume Rendering (HVR) framework has been extended to accommodate parallel compositing where previously only serial compositing was possible. The preliminary results show improvements in the compositing times for direct send even for a small number of processors. Unfortunately, the results of binary swap exhibit a negative behavior. This is due to the naive use of the graphics hardware blending mechanism. The expensive transfers account for the lengthy compositing times. The second part targets the development of scalable and intuitive interaction mechanisms. It introduces the development of a new client application for multitouch tablet devices, like the Apple iPad. The main goal is to provide the HVR framework, that has been extended to use tiled displays, a more intuitive and portable interaction mechanism that can get advantage of the new environment. The previous client is a PC application for the typical desktop settings that use a mouse and keyboard as sources of interaction. The current implementation of the client lets the user steer and

  13. Quisqualate-activated single channel currents in neuromuscular preparations of small and large crayfish.

    Science.gov (United States)

    Finger, W; Martin, C; Pareto, A

    1988-06-01

    Single channel currents elicited by 1-5 mumol/l quisqualate in neuromuscular preparations in large (greater than 16 month old) and small (1-3 month old) crayfish were recorded by means of the patch-clamp technique. In preparations from large crayfish single channel currents of variable amplitude (-1 to -12 pA) were induced by quisqualate. The mean burst lengths of these currents were tau approximately equal to 1-2 ms. In the opener muscle of the first walking leg and the contractor epimeralis muscle of small crayfish the mean burst lengths of single channel currents evoked by quisqualate were prolonged by a factor of about 4 (tau approximately equal to 5 ms). Moreover, in the opener muscle of the first walking leg of small crayfish single channel currents of small amplitude (-0.5 to -2.5 pA) were preferentially evoked by quisqualate. By contrast, in the contractor epimeralis muscle of small crayfish mainly single channel currents of large amplitude (-10 to -12 pA) were elicited by quisqualate. The results suggest that at the stage of neuromuscular development characterizing the small crayfish, gating properties of excitatory postsynaptic channels are different from those in adult crayfish. Furthermore, the results obtained in the opener muscle of the first walking leg of small crayfish are consistent with those obtained previously by means of the noise analysis technique.

  14. Electromagnetic design of the KATRIN large-volume air coil system

    CERN Document Server

    Glück, Ferenc; Leiber, Benjamin; Mertens, Susanne; Osipowicz, Alexander; Reich, Jan; Wandkowsky, Nancy

    2013-01-01

    The KATRIN experiment is designed to determine the absolute neutrino mass scale with a sensitivity of 200 meV (90 % CL) by measuring the electron energy spectrum close to the endpoint of molecular tritium beta decay. Electrons from a high-intensity gaseous tritium source are guided by a strong magnetic field of a few T to the analyzing plane of the main spectrometer where an integral energy analysis takes place in a low field region (B<0.5 mT). An essential design feature to obtain adiabatic electron transport through this spectrometer is a large volume air coil system surrounding the vessel. The system has two key tasks: to adjust and fine-tune the magnetic guiding field (Low Field Correction System), as well as to compensate the distorting effects of the earth magnetic field (Earth Field Compensation System). In this paper we outline the key electromagnetic design issues for this very large air coil system, which allows for well-defined electron transmission and optimized background reduction in the KATR...

  15. Major risk from rapid, large-volume landslides in Europe (EU Project RUNOUT)

    Science.gov (United States)

    Kilburn, Christopher R. J.; Pasuto, Alessandro

    2003-08-01

    Project RUNOUT has investigated methods for reducing the risk from large-volume landslides in Europe, especially those involving rapid rates of emplacement. Using field data from five test sites (Bad Goisern and Köfels in Austria, Tessina and Vajont in Italy, and the Barranco de Tirajana in Gran Canaria, Spain), the studies have developed (1) techniques for applying geomorphological investigations and optical remote sensing to map landslides and their evolution; (2) analytical, numerical, and cellular automata models for the emplacement of sturzstroms and debris flows; (3) a brittle-failure model for forecasting catastrophic slope failure; (4) new strategies for integrating large-area Global Positioning System (GPS) arrays with local geodetic monitoring networks; (5) methods for raising public awareness of landslide hazards; and (6) Geographic Information System (GIS)-based databases for the test areas. The results highlight the importance of multidisciplinary studies of landslide hazards, combining subjects as diverse as geology and geomorphology, remote sensing, geodesy, fluid dynamics, and social profiling. They have also identified key goals for an improved understanding of the physical processes that govern landslide collapse and runout, as well as for designing strategies for raising public awareness of landslide hazards and for implementing appropriate land management policies for reducing landslide risk.

  16. Beautiful small: Misleading large randomized controlled trials? The example of colloids for volume resuscitation

    Directory of Open Access Journals (Sweden)

    Christian J Wiedermann

    2015-01-01

    Full Text Available In anesthesia and intensive care, treatment benefits that were claimed on the basis of small or modest-sized trials have repeatedly failed to be confirmed in large randomized controlled trials. A well-designed small trial in a homogeneous patient population with high event rates could yield conclusive results; however, patient populations in anesthesia and intensive care are typically heterogeneous because of comorbidities. The size of the anticipated effects of therapeutic interventions is generally low in relation to relevant endpoints. For regulatory purposes, trials are required to demonstrate efficacy in clinically important endpoints, and therefore must be large because clinically important study endpoints such as death, sepsis, or pneumonia are dichotomous and infrequently occur. The rarer endpoint events occur in the study population; that is, the lower the signal-to-noise ratio, the larger the trials must be to prevent random events from being overemphasized. In addition to trial design, sample size determination on the basis of event rates, clinically meaningful risk ratio reductions and actual patient numbers studied are among the most important characteristics when interpreting study results. Trial size is a critical determinant of generalizability of study results to larger or general patient populations. Typical characteristics of small single-center studies responsible for their known fragility include low variability of outcome measures for surrogate parameters and selective publication and reporting. For anesthesiology and intensive care medicine, findings in volume resuscitation research on intravenous infusion of colloids exemplify this, since both the safety of albumin infusion and the adverse effects of the artificial colloid hydroxyethyl starch have been confirmed only in large-sized trials.

  17. Technical and dosimetric considerations in IMRT treatment planning for large target volumes.

    Science.gov (United States)

    Malhotra, Harish K; Raina, Sanjay; Avadhani, Jaiteerth S; deBoer, Steven; Podgorsak, Matthew B

    2005-01-01

    The maximum width of an intensity-modulated radiotherapy (IMRT) treatment field is usually smaller than the conventional maximum collimator opening because of design limitations inherent in some multileaf collimators (MLCs). To increase the effective field width, IMRT fluences can be split and delivered with multiple carriage positions. However, not all treatment-planning systems and MLCs support this technique, and if they do, the maximum field width in multiple carriage position delivery is still significantly less than the maximum collimator opening. For target volumes with dimensions exceeding the field size limit for multiple carriage position delivery, such as liver tumors or other malignancies in the abdominal cavity, IMRT treatment can be accomplished with multiple isocenters or with an extended treatment distance. To study dosimetric statistics of large field IMRT planning, an elliptical volume was chosen as a target within a cubic phantom centered at a depth of 7.5 cm. Multiple three-field plans (one AP and two oblique beams with 160 degrees between them to avoid parallel opposed geometry) with constraints designed to give 100% dose to the elliptical target were developed. Plans were designed with a single anterior field with dual carriage positions, or with the anterior field split into two fields with separate isocenters 8 cm apart with the beams being forcibly matched at the isocenter or with a 1 cm, 2 cm, 3 cm, and 4 cm overlap. The oblique beams were planned with a single carriage position in all cases. All beams had a nominal energy of 6 MV. In the dual isocenter plans, jaws were manually fixed and dose constraints remained unaltered. Dosimetric statistics were studied for plans developed for treatment delivery using both dynamic leaf motion (sliding window) and multiple static segments (step and shoot) with the number of segments varying from 5 to 30. All plans were analyzed based on the dose homogeneity in the isocenter plane, 2 cm anterior and 2

  18. Optimum parity of volumes of training loadings in the one-cyclic experimental period of preparation taekwondo athletes high qualification

    Directory of Open Access Journals (Sweden)

    Saienko V.G.

    2010-09-01

    Full Text Available Efficiency of application of correlation of volumes of the trainings loadings is tested in preparation of sportsmen. 12 sportsmen took part in an experiment (age of 18-22, experience of employments from 8 to 15 years. On the extent of three months the program of preparation was used. All sportsmen conducted the identical amount of trainings employments - 105. The most effective construction of training process of sportsmen is certain in one-cyclic three months period. It has such correlation of volumes of trainings facilities: base technique - 10%, formal complexes of battle exercises - 9%, specially-preparatory exercises - 24%, exercises on shells - 17%, exercises with a partner - 17%, sparrings - 23%.

  19. Mass Spectrometry as a Preparative Tool for the Surface Science of Large Molecules

    Science.gov (United States)

    Rauschenbach, Stephan; Ternes, Markus; Harnau, Ludger; Kern, Klaus

    2016-06-01

    Measuring and understanding the complexity that arises when nanostructures interact with their environment are one of the major current challenges of nanoscale science and technology. High-resolution microscopy methods such as scanning probe microscopy have the capacity to investigate nanoscale systems with ultimate precision, for which, however, atomic scale precise preparation methods of surface science are a necessity. Preparative mass spectrometry (pMS), defined as the controlled deposition of m/z filtered ion beams, with soft ionization sources links the world of large, biological molecules and surface science, enabling atomic scale chemical control of molecular deposition in ultrahigh vacuum (UHV). Here we explore the application of high-resolution scanning probe microscopy and spectroscopy to the characterization of structure and properties of large molecules. We introduce the fundamental principles of the combined experiments electrospray ion beam deposition and scanning tunneling microscopy. Examples for the deposition and investigation of single particles, for layer and film growth, and for the investigation of electronic properties of individual nonvolatile molecules show that state-of-the-art pMS technology provides a platform analog to thermal evaporation in conventional molecular beam epitaxy. Additionally, it offers additional, unique features due to the use of charged polyatomic particles. This new field is an enormous sandbox for novel molecular materials research and demands the development of advanced molecular ion beam technology.

  20. Storage and eruption of large volumes of rhyolite lava: Example from Solfatara Plateau, Yellowstone Caldera

    Science.gov (United States)

    Befus, K.; Gardner, J. E.; Zinke, R.

    2010-12-01

    The cataclysmic volcanic history of Yellowstone caldera has been extensively documented in both popular media and scholarly journals. High-silica magmas should erupt explosively because of their high viscosity and volatile content; however, numerous passively-erupted, large-volume rhyolite lava flows have also erupted from Yellowstone caldera. We use petrologic observations of one such flow, the Solfatara Plateau obsidian lava, to provide insights into the eruptive dynamics and pre-eruptive magmatic conditions of large-volume rhyolite lava. Solfatara Plateau, a 7 km3 high-silica rhyolite lava that extends 4-15 km from vent, erupted 103±8 ka within the Yellowstone caldera1. Quartz and sanidine are the dominant phenocrysts, with crystal contents of 5-10% throughout. FTIR analyses of glass inclusions in quartz and sanidine phenocrysts indicate that pre-eruptive dissolved volatile contents were up to 3.0 wt. % H2O and 250 ppm CO2. Myrmekite blebs partially envelop quartz and sanidine phenocrysts in all samples from along the margins of the flow (up to 3 km from flow front). Sanidines in samples from near vent are unzoned at Or49±2. Those at the flow front have similar cores, but rims are more sodic (Or44±6). Alkali feldspars in myrmekite range from Or27 to Or50. Petrologic observations, such as heavily embayed quartz phenocrysts and dissolution of myrmekite indicate disequilibrium within the system, likely as a result of significant heating that caused portions of the magma body to go from near-solidus to near-liquidus conditions prior to erupting. When it did erupt, volatile loss during eruptive ascent led to undercooling and significant microlite crystallization of Fe-Ti oxide and clinopyroxene microlites. Fe-Ti microlites occur as roughly equidimensional crystals, 1-10 µm across, as well as high-aspect-ratio needles, 3-60 µm long. Clinopyroxene microlites occur primarily as individual prismatic crystals, but also occur as linked, curved chains or as overgrowths

  1. Annealing as grown large volume CZT single crystals increased spectral resolution

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Longxia Li

    2008-03-19

    The spectroscopic performance of current large-volume Cadmium 10% Zinc Telluride, Cd{sub 0.9}Zn{sub 0.1}Te, (CZT) detectors is impaired by cumulative effect of tellurium precipitates (secondary phases) presented in CZT single-crystal grown by low-pressure Bridgman techniques(1). This statistical effect may limit the energy resolution of large-volume CZT detectors (typically 2-5% at 662 keV for 12-mm thick devices). The stochastic nature of the interaction prevents the use of any electronic or digital charge correction techniques without a significant reduction in the detector efficiency. This volume constraint hampers the utility of CZT since the detectors are inefficient at detecting photons >1MeV and/or in low fluency situations. During the project, seven runs CZT ingots have been grown, in these ingots the indium dopant concentrations have been changed in the range between 0.5ppm to 6ppm. The I-R mapping imaging method has been employed to study the Te-precipitates. The Teprecipitates in as-grown CZT wafers, and after annealing wafers have been systematically studied by using I-R mapping system (home installed, resolution of 1.5 {micro}m). We employed our I-R standard annealing CZT (Zn=4%) procedure or two-steps annealing into radiation CZT (Zn=10%), we achieved the 'non'-Te precipitates (size < 1 {micro}m) CZT n+-type with resistivity > 10{sup 9-10} {Omega}-cm. We believe that the Te-precipitates are the p-type defects, its reducing number causes the CZT became n+-type, therefore we varied or reduced the indium dapant concentration during the growth and changed the Te-precipitates size and density by using different Cd-temperature and different annealing procedures. We have made the comparisons among Te-precipitates size, density and Indium dopant concentrations, and we found that the CZT with smaller size of Te-precipitates is suitable for radiation uses but non-Te precipitates is impossible to be used in the radiation detectors, because the CZT

  2. A new large-volume metal reference standard for radioactive waste management.

    Science.gov (United States)

    Tzika, F; Hult, M; Stroh, H; Marissens, G; Arnold, D; Burda, O; Kovář, P; Suran, J; Listkowska, A; Tyminski, Z

    2016-03-01

    A new large-volume metal reference standard has been developed. The intended use is for calibration of free-release radioactivity measurement systems and is made up of cast iron tubes placed inside a box of the size of a Euro-pallet (80 × 120 cm). The tubes contain certified activity concentrations of (60)Co (0.290 ± 0.006 Bq g(-1)) and (110m)Ag (3.05 ± 0.09 Bq g(-1)) (reference date: 30 September 2013). They were produced using centrifugal casting from a smelt into which (60)Co was first added and then one piece of neutron irradiated silver wire was progressively diluted. The iron castings were machined to the desirable dimensions. The final material consists of 12 iron tubes of 20 cm outer diameter, 17.6 cm inner diameter, 40 cm length/height and 245.9 kg total mass. This paper describes the reference standard and the process of determining the reference activity values. © The Author 2015. Published by Oxford University Press.

  3. Determination of the efficiency of a detector in gamma spectrometry of large-volume samples

    CERN Document Server

    Tertyshnik, E G

    2012-01-01

    The experimental - calculated method is proposed to determine the full energy peak efficiency (FEPE) of detectors {\\epsilon}(E) in case a measurement of the large-volume samples. Water is used as standard absorber in which the linear attenuation coefficients for photons {\\mu}0 (E) is well known. The value {\\mu} (E) in sample material (matrix of the sample) is determined experimentally by means of spectrometer. The formulas are given for calculation of the ratio {\\epsilon}(E)/ {\\epsilon}0(E), where {\\epsilon}0(E) is FEPE of the detector for photons those are arising in the container filled with water (it is found by adding in the container of the Reference radioactive solutions). To prove the validity of the method ethanol (density 0,8 g/cm3) and water solutions of salts (density 1,2 and 1,5 g/cm3) were used for simulation of the samples with different attenuation coefficients. Standard deviation between experimental and calculated efficiencies has been about 5 %.

  4. Twinning in vapour-grown, large volume Cd1-xZnxTe crystals

    Science.gov (United States)

    Tanner, B. K.; Mullins, J. T.; Pym, A. T. G.; Maneuski, D.

    2016-08-01

    The onset of twinning from (2 bar 1 bar 1 bar) to (1 bar 3 bar 3 bar) in large volume Cd1-xZnxTe crystals, grown by vapour transport on (2 bar 1 bar 1 bar) , often referred to as (211)B, oriented GaAs seeds, has been investigated using X-ray diffraction imaging (X-ray topography). Twinning is not associated with strains at the GaAs/CdTe interface as the initial growth was always in (2 bar 1 bar 1 bar) orientation. Nor is twinning related to lattice strains associated with injection of Zn subsequent to initial nucleation and growth of pure CdTe as in both cases twinning occurred after growth of several mm length of Cd1-xZnxTe. While in both cases examined, there was a region of disturbed growth prior to the twinning transition, in neither crystal does this strain appear to have nucleated the twinning process. In both cases, un-twinned material remained after twinning was observed, the scale of the resulting twin boundaries being sub-micron. Simultaneous twinning across the whole sample surface was observed in one sample, whereas in the other, twinning was nucleated at different points and times in the growth.

  5. Development of a large mosaic volume phase holographic (VPH) grating for APOGEE

    Science.gov (United States)

    Arns, James; Wilson, John C.; Skrutskie, Mike; Smee, Steve; Barkhouser, Robert; Eisenstein, Daniel; Gunn, Jim; Hearty, Fred; Harding, Al; Maseman, Paul; Holtzman, Jon; Schiavon, Ricardo; Gillespie, Bruce; Majewski, Steven

    2010-07-01

    Volume phase holographic (VPH) gratings are increasingly being used as diffractive elements in astronomical instruments due to their potential for very high peak diffraction efficiencies and the possibility of a compact instrument design when the gratings are used in transmission. Historically, VPH grating (VPHG) sizes have been limited by the size of manufacturer's holographic recording optics. We report on the design, specification and fabrication of a large, 290 mm × 475 mm elliptically-shaped, mosaic VPHG for the Apache Point Observatory Galactic Evolution Experiment (APOGEE) spectrograph. This high-resolution near-infrared multi-object spectrograph is in construction for the Sloan Digital Sky Survey III (SDSS III). The 1008.6 lines/mm VPHG was designed for optimized performance over a wavelength range from 1.5 to 1.7 μm. A step-and-repeat exposure method was chosen to fabricate a three-segment mosaic on a 305 mm × 508 mm monolithic fused-silica substrate. Specification considerations imposed on the VPHG to assure the mosaic construction will satisfy the end use requirements are discussed. Production issues and test results of the mosaic VPHG are discussed.

  6. Measurement of Throughput Variation Across A Large Format Volume-Phase Holographic Grating

    CERN Document Server

    Tamura, N; Sharples, R M; Robertson, D J; Allington-Smith, J R; Tamura, Naoyuki; Murray, Graham J.; Sharples, Ray M.; Robertson, David J.

    2005-01-01

    In this paper, we report measurements of diffraction efficiency and angular dispersion for a large format (~ 25 cm diameter) Volume-Phase Holographic (VPH) grating optimized for near-infrared wavelengths (0.9 -- 1.8 micron). The aim of this experiment is to see whether optical characteristics vary significantly across the grating. We sampled three positions in the grating aperture with a separation of 5 cm between each. A 2 cm diameter beam is used to illuminate the grating. At each position, throughput and diffraction angle were measured at several wavelengths. It is found that whilst the relationship between diffraction angle and wavelength is nearly the same at the three positions, the throughputs vary by up to ~ 10\\% from position to position. We explore the origin of the throughput variation by comparing the data with predictions from coupled-wave analysis. We find that it can be explained by a combination of small variations over the grating aperture in gelatin depth and/or refractive index modulation a...

  7. Curling probe measurement of large-volume pulsed plasma confined by surface magnetic field

    Science.gov (United States)

    Pandey, Anil; Sakakibara, Wataru; Matsuoka, Hiroyuki; Nakamura, Keiji; Sugai, Hideo; Chubu University Team; DOWA Thermotech Collaboration

    2015-09-01

    Curling probe (CP) has recently been developed which enables the local electron density measurement even in plasma for non-conducting film CVD. The electron density is obtained from a shift of resonance frequency of spiral antenna in discharge ON and OFF monitored by a network analyzer (NWA). In case of a pulsed glow discharge, synchronization of discharge pulse with frequency sweep of NWA must be established. In this paper, we report time and space-resolved CP measurement of electron density in a large volume plasma (80 cm diameter, 110 cm length) confined by surface magnetic field (multipole cusp field ~0.03 T). For plasma-aided modification of metal surface, the plasma is produced by 1 kV glow discharge at pulse frequency of 0.3 - 25 kHz with various duty ratio in gas (Ar, N2, C2H2) at pressure ~ 1 Pa. A radially movable CP revealed a remarkable effect of surface magnetic confinement: detach of plasma from the vessel wall and a fairly uniform plasma in the central region. In afterglow phase, the electron density was observed to decrease much faster in C2H2 discharge than in Ar discharge.

  8. Curling probe measurement of a large-volume pulsed plasma with surface magnetic confinement

    Science.gov (United States)

    Pandey, A.; Tashiro, H.; Sakakibara, W.; Nakamura, K.; Sugai, H.

    2016-12-01

    A curling probe (CP) based on microwave resonance is applied to the measurement of electron density in a pulsed DC glow discharge under surface magnetic confinement (SMC) provided by a number of permanent magnets on a chamber wall. Owing to the SMC effects, a 1 m scale large-volume plasma is generated by a relatively low voltage (~1 kV) at low pressure (~1 Pa) in various gases (Ar, CH4, and C2H2). Temporal variation of the electron density is measured for pulse frequency f  =  0.5-25 kHz for various discharge-on times (T ON) with a high resolution time (~0.2 µs), using the on-point mode. In general, the electron density starts to increase at time t  =  0 after turn-on of the discharge voltage, reaches peak density at t  =  T ON, and then decreases after turn-off. The peak electron density is observed to increase with the pulse frequency f for constant T ON owing to the residual plasma. This dependence is successfully formulated using a semi-empirical model. The spatio-temporal evolution of the cathode sheath in the pulsed discharge is revealed by a 1 m long movable CP. The measured thickness of the high-voltage cathode fall in a steady state coincides with the value of the so-called Child-Langmuir sheath.

  9. Development testing of large volume water sprays for warm fog dispersal

    Science.gov (United States)

    Keller, V. W.; Anderson, B. J.; Burns, R. A.; Lala, G. G.; Meyer, M. B.; Beard, K. V.

    1986-01-01

    A new brute-force method of warm fog dispersal is described. The method uses large volume recycled water sprays to create curtains of falling drops through which the fog is processed by the ambient wind and spray induced air flow. Fog droplets are removed by coalescence/rainout. The efficiency of the technique depends upon the drop size spectra in the spray, the height to which the spray can be projected, the efficiency with which fog laden air is processed through the curtain of spray, and the rate at which new fog may be formed due to temperature differences between the air and spray water. Results of a field test program, implemented to develop the data base necessary to assess the proposed method, are presented. Analytical calculations based upon the field test results indicate that this proposed method of warm fog dispersal is feasible. Even more convincingly, the technique was successfully demonstrated in the one natural fog event which occurred during the test program. Energy requirements for this technique are an order of magnitude less than those to operate a thermokinetic system. An important side benefit is the considerable emergency fire extinguishing capability it provides along the runway.

  10. High-Dimensional Function Approximation With Neural Networks for Large Volumes of Data.

    Science.gov (United States)

    Andras, Peter

    2017-01-25

    Approximation of high-dimensional functions is a challenge for neural networks due to the curse of dimensionality. Often the data for which the approximated function is defined resides on a low-dimensional manifold and in principle the approximation of the function over this manifold should improve the approximation performance. It has been show that projecting the data manifold into a lower dimensional space, followed by the neural network approximation of the function over this space, provides a more precise approximation of the function than the approximation of the function with neural networks in the original data space. However, if the data volume is very large, the projection into the low-dimensional space has to be based on a limited sample of the data. Here, we investigate the nature of the approximation error of neural networks trained over the projection space. We show that such neural networks should have better approximation performance than neural networks trained on high-dimensional data even if the projection is based on a relatively sparse sample of the data manifold. We also find that it is preferable to use a uniformly distributed sparse sample of the data for the purpose of the generation of the low-dimensional projection. We illustrate these results considering the practical neural network approximation of a set of functions defined on high-dimensional data including real world data as well.

  11. Exporting large volumes of municipal sewage sludge through turfgrass sod production.

    Science.gov (United States)

    Tesfamariam, Eyob H; Annandale, John G; Steyn, Joachim M; Stirzaker, Richard J

    2009-01-01

    The nutrient content of sludge produced by municipal water treatment works often far exceeds the requirements of nearby crops. Transporting sludge further afield is not always economically viable. This study reports on the potential to export large volumes of anaerobically digested municipal sewage sludge through turfgrass sod production. Hypotheses examined are that sludge loading rates far above recommendations based on crop nutrient removal (i) are possible without reducing turf growth and quality, (ii) do not cause an accumulation of N and P below the active root zone, (iii) can minimize soil loss through sod harvesting, and (iv) do not cause unacceptably high nitrate and salt leaching. An 8 Mg ha(-1) sludge control (the recommended limit) was compared with sludge rates of 0, 33, 67, and 100 Mg ha(-1) on a loamy, kaolinitic, mesic, Typic Eutrustox soil near Johannesburg, South Africa. Sludge application rates up to 67 Mg ha(-1) significantly improved turfgrass establishment rate and color. The ability of sods to remain intact during handling and transport improved as the sludge application rate increased to 33 Mg ha(-1) but deteriorated at higher rates. A sludge application rate of 100 Mg ha(-1) was needed to eliminate soil loss, but this rate was associated with unacceptably high N leaching losses. All our hypotheses were accepted for application rates not exceeding 33 Mg ha(-1) on the proviso that some soil loss was acceptable and that the leaching fraction was carefully managed during the first 2 mo after sludge application.

  12. Practical gamma spectroscopy assay techniques for large volume low-level waste boxes.

    Energy Technology Data Exchange (ETDEWEB)

    Myers, S. C. (Steven C.); Gruetzmacher, K. M. (Kathleen M.); Scheffing, C. C. (Candice C.); Gallegos, L. E. (Lucas E.); Bustos, R. M. (Roland M.)

    2002-01-01

    A study was conducted at the Los Alamos National Laboratory (LANL) to evaluate the performance of the SNAPrM (Spectral Nondestructive Assay Platform) analytical software for measurements of known standards in large metal waste boxes (2.5 m' volume). The trials were designed to test the accuracy and variance of the analytical results for low-density combustible matrices and higher-density metal matrices at two discrete gamma-ray energies: 121.78 keV and 411.12 keV. For both matrix types the measurement method that produced the most accurate results with the lowest associated standard deviation involved combining four individual measurements taken at the geometric center of each of the box's four vertical sides. With this method the overall bias and the standard deviation amongst 24 individual results for the 121.78 keV and 411.12 keV gamma rays were as follows: 3.38% (k 20.19%) and 3.68% (k 15.47%) for the combustible matrix and 37,88% (k 67.64%) and 9.38% (k 33.15%) for the metal matrix. The persistent positive bias from measurements of the metal box is believed to be a result of a nonhomogenously distributed matrix.

  13. Configuration Analysis of the ERS Points in Large-Volume Metrology System.

    Science.gov (United States)

    Jin, Zhangjun; Yu, Cijun; Li, Jiangxiong; Ke, Yinglin

    2015-09-22

    In aircraft assembly, multiple laser trackers are used simultaneously to measure large-scale aircraft components. To combine the independent measurements, the transformation matrices between the laser trackers' coordinate systems and the assembly coordinate system are calculated, by measuring the enhanced referring system (ERS) points. This article aims to understand the influence of the configuration of the ERS points that affect the transformation matrix errors, and then optimize the deployment of the ERS points to reduce the transformation matrix errors. To optimize the deployment of the ERS points, an explicit model is derived to estimate the transformation matrix errors. The estimation model is verified by the experiment implemented in the factory floor. Based on the proposed model, a group of sensitivity coefficients are derived to evaluate the quality of the configuration of the ERS points, and then several typical configurations of the ERS points are analyzed in detail with the sensitivity coefficients. Finally general guidance is established to instruct the deployment of the ERS points in the aspects of the layout, the volume size and the number of the ERS points, as well as the position and orientation of the assembly coordinate system.

  14. Detecting Boosted Dark Matter from the Sun with Large Volume Neutrino Detectors

    Energy Technology Data Exchange (ETDEWEB)

    Berger, Joshua; /SLAC; Cui, Yanou; /Perimeter Inst. Theor. Phys.; Zhao, Yue; /Stanford U., ITP /Stanford U., Phys. Dept.

    2015-04-02

    We study novel scenarios where thermal dark matter (DM) can be efficiently captured in the Sun and annihilate into boosted dark matter. In models with semi-annihilating DM, where DM has a non-minimal stabilization symmetry, or in models with a multi-component DM sector, annihilations of DM can give rise to stable dark sector particles with moderate Lorentz boosts. We investigate both of these possibilities, presenting concrete models as proofs of concept. Both scenarios can yield viable thermal relic DM with masses O(1)-O(100) GeV. Taking advantage of the energetic proton recoils that arise when the boosted DM scatters off matter, we propose a detection strategy which uses large volume terrestrial detectors, such as those designed to detect neutrinos or proton decays. In particular, we propose a search for proton tracks pointing towards the Sun. We focus on signals at Cherenkov-radiation-based detectors such as Super-Kamiokande (SK) and its upgrade Hyper-Kamiokande (HK). We find that with spin-dependent scattering as the dominant DM-nucleus interaction at low energies, boosted DM can leave detectable signals at SK or HK, with sensitivity comparable to DM direct detection experiments while being consistent with current constraints. Our study provides a new search path for DM sectors with non-minimal structure.

  15. Technical Note: The determination of enclosed water volume in large flexible-wall mesocosms "KOSMOS"

    Directory of Open Access Journals (Sweden)

    J. Czerny

    2013-03-01

    Full Text Available The volume of water enclosed inside flexible-wall mesocosm bags is hard to estimate using geometrical calculations and can be strongly variable among bags of the same dimensions. Here we present a method for precise water volume determination in mesocosms using salinity as a tracer. Knowledge of the precise volume of water enclosed allows establishment of exactly planned treatment concentrations and calculation of elemental budgets.

  16. Methods for the preparation of large quantities of complex single-stranded oligonucleotide libraries.

    Directory of Open Access Journals (Sweden)

    Yusuf E Murgha

    Full Text Available Custom-defined oligonucleotide collections have a broad range of applications in fields of synthetic biology, targeted sequencing, and cytogenetics. Also, they are used to encode information for technologies like RNA interference, protein engineering and DNA-encoded libraries. High-throughput parallel DNA synthesis technologies developed for the manufacture of DNA microarrays can produce libraries of large numbers of different oligonucleotides, but in very limited amounts. Here, we compare three approaches to prepare large quantities of single-stranded oligonucleotide libraries derived from microarray synthesized collections. The first approach, alkaline melting of double-stranded PCR amplified libraries with a biotinylated strand captured on streptavidin coated magnetic beads results in little or no non-biotinylated ssDNA. The second method wherein the phosphorylated strand of PCR amplified libraries is nucleolyticaly hydrolyzed is recommended when small amounts of libraries are needed. The third method combining in vitro transcription of PCR amplified libraries to reverse transcription of the RNA product into single-stranded cDNA is our recommended method to produce large amounts of oligonucleotide libraries. Finally, we propose a method to remove any primer binding sequences introduced during library amplification.

  17. Methods for the preparation of large quantities of complex single-stranded oligonucleotide libraries.

    Science.gov (United States)

    Murgha, Yusuf E; Rouillard, Jean-Marie; Gulari, Erdogan

    2014-01-01

    Custom-defined oligonucleotide collections have a broad range of applications in fields of synthetic biology, targeted sequencing, and cytogenetics. Also, they are used to encode information for technologies like RNA interference, protein engineering and DNA-encoded libraries. High-throughput parallel DNA synthesis technologies developed for the manufacture of DNA microarrays can produce libraries of large numbers of different oligonucleotides, but in very limited amounts. Here, we compare three approaches to prepare large quantities of single-stranded oligonucleotide libraries derived from microarray synthesized collections. The first approach, alkaline melting of double-stranded PCR amplified libraries with a biotinylated strand captured on streptavidin coated magnetic beads results in little or no non-biotinylated ssDNA. The second method wherein the phosphorylated strand of PCR amplified libraries is nucleolyticaly hydrolyzed is recommended when small amounts of libraries are needed. The third method combining in vitro transcription of PCR amplified libraries to reverse transcription of the RNA product into single-stranded cDNA is our recommended method to produce large amounts of oligonucleotide libraries. Finally, we propose a method to remove any primer binding sequences introduced during library amplification.

  18. 3-D EM exploration of the hepatic microarchitecture – lessons learned from large-volume in situ serial sectioning

    OpenAIRE

    Gerald John Shami; Delfine Cheng; Minh Huynh; Celien Vreuls; Eddie Wisse; Filip Braet

    2016-01-01

    To-date serial block-face scanning electron microscopy (SBF-SEM) dominates as the premier technique for generating three-dimensional (3-D) data of resin-embedded biological samples at an unprecedented depth volume. Given the infancy of the technique, limited literature is currently available regarding the applicability of SBF-SEM for the ultrastructural investigation of tissues. Herein, we provide a comprehensive and rigorous appraisal of five different SBF-SEM sample preparation protocols fo...

  19. Stem cell harvesting protocol research in autologous transplantation setting: Large volume vs. conventional cytapheresis

    Directory of Open Access Journals (Sweden)

    Balint Bela

    2008-01-01

    Full Text Available Background/Aim. The use of peripheral blood as a source of hematopoietic stem cells (SCs is progressively increasing and has nearly supplanted bone marrow transplantation. Interpatient variability in the degree and kinetics of SC mobilization into peripheral blood is an expected event after conventional chemotherapy-based treatment, followed by sequential administration of recombinant granulocyte-colony- stimulating factor (rHu-CSF. In this study, specific factors associated with the application of two different SC-harvesting approaches, including the use of large volume leukapheresis (LVL vs. repetitive conventional apheresis (RCA, were analyzed. The basic goal of the study was to evaluate the influence of apheresis protocol (collection timing, processed blood volume and cell yield upon the clinical outcome of transplantation. Methods. Results obtained by LVL (76 pts and RCA (20 pts - control group were compared. The SC mobilizing regimen used was cyclophosphamide (4-7 g/m2 or polychemotherapy and rHuG-CSF 10-16 μg/kg of body mess (bm per day. Cell harvesting was performed using COBE-Spectra (Caridian-BCT, USA. The volume of processed blood in LVL setting was ≥ 3.5 - fold of the patient's circulating blood quantity (ranged from 12.7 to 37.8 l. All patients tolerated well the use of intensive treatment, without any side or adverse effects. Our original controlled-rate cryopreservation was carried out with 10% dimethyl sulfoxide (DMSO using Planer R203/200R or Planer 560-16 equipments (Planer Products Ltd, UK. Total nucleated cell (NC and mononuclear cell (MNC counts were examined by flow cytometry (Advia-2120 Bayer, Germany; Technicon H-3 System, USA. The CD34+ cell surface antigen was investigated by the EPICS XL-MCL device (Coulter, Germany. Results. Performing LVL-apheresis, high-level MNC and CD34+ cell yields (7.6±4.6 × 108/kg bm and 11.8±6.5 × 106/kg bm, respectively were obtained. As a result, rapid hematopoietic reconstitution

  20. Large parallel volumes of finite and compact sets in d-dimensional Euclidean space

    DEFF Research Database (Denmark)

    Kampf, Jürgen; Kiderlen, Markus

    The r-parallel volume V (Cr) of a compact subset C in d-dimensional Euclidean space is the volume of the set Cr of all points of Euclidean distance at most r > 0 from C. According to Steiner’s formula, V (Cr) is a polynomial in r when C is convex. For finite sets C satisfying a certain geometric ...

  1. A pomegranate-inspired nanoscale design for large-volume-change lithium battery anodes

    Science.gov (United States)

    Liu, Nian; Lu, Zhenda; Zhao, Jie; McDowell, Matthew T.; Lee, Hyun-Wook; Zhao, Wenting; Cui, Yi

    2014-03-01

    Silicon is an attractive material for anodes in energy storage devices, because it has ten times the theoretical capacity of its state-of-the-art carbonaceous counterpart. Silicon anodes can be used both in traditional lithium-ion batteries and in more recent Li-O2 and Li-S batteries as a replacement for the dendrite-forming lithium metal anodes. The main challenges associated with silicon anodes are structural degradation and instability of the solid-electrolyte interphase caused by the large volume change (~300%) during cycling, the occurrence of side reactions with the electrolyte, and the low volumetric capacity when the material size is reduced to a nanometre scale. Here, we propose a hierarchical structured silicon anode that tackles all three of these problems. Our design is inspired by the structure of a pomegranate, where single silicon nanoparticles are encapsulated by a conductive carbon layer that leaves enough room for expansion and contraction following lithiation and delithiation. An ensemble of these hybrid nanoparticles is then encapsulated by a thicker carbon layer in micrometre-size pouches to act as an electrolyte barrier. As a result of this hierarchical arrangement, the solid-electrolyte interphase remains stable and spatially confined, resulting in superior cyclability (97% capacity retention after 1,000 cycles). In addition, the microstructures lower the electrode-electrolyte contact area, resulting in high Coulombic efficiency (99.87%) and volumetric capacity (1,270 mAh cm-3), and the cycling remains stable even when the areal capacity is increased to the level of commercial lithium-ion batteries (3.7 mAh cm-2).

  2. Addressing challenges in bar-code scanning of large-volume infusion bags.

    Science.gov (United States)

    Raman, Kirthana; Heelon, Mark; Kerr, Gary; Higgins, Thomas L

    2011-08-01

    A hospital pharmacy's efforts to identify and address challenges with bedside scanning of bar codes on large-volume parenteral (LVP) infusion bags are described. Bar-code-assisted medication administration (BCMA) has been shown to reduce medication errors and improve patient safety. After the pilot implementation of a BCMA system and point-of-care scanning procedures at a medical center's intensive care unit, it was noted that nurses' attempted bedside scans of certain LVP bags for product identification purposes often were not successful. An investigation and root-cause analysis, including observation of nurses' scanning technique by a multidisciplinary team, determined that the scanning failures stemmed from the placement of two bar-code imprints-one with the product identification code and another, larger imprint with the expiration date and lot number-adjacently on the LVP bags. The nursing staff was educated on a modified scanning technique, which resulted in significantly improved success rates in the scanning of the most commonly used LVP bags. Representatives of the LVP bag manufacturer met with hospital staff to discuss the problem and corrective measures. As part of a subsequent infusion bag redesign, the manufacturer discontinued the use of the bar-code imprint implicated in the scanning failures. Failures in scanning LVP bags were traced to problematic placement of bar-code imprints on the bags. Interdisciplinary collaboration, consultation with the bag manufacturer, and education of the nursing and pharmacy staff resulted in a reduction in scanning failures and the manufacturer's removal of one of the bar codes from its LVP bags.

  3. Type IIB orientifolds, D-brane instantons and the large volume scenario

    Energy Technology Data Exchange (ETDEWEB)

    Plauschinn, Erik

    2009-07-28

    This thesis is concerned with a branch of research in String Theory called String Phenomenology which aims for a better understanding of the connection between String Theory and Particle Physics. In particular, in this work we cover three topics which are important in order to establish this connection. The first topic is about String Theory model building in the context of so-called type IIB orientifolds with orientifold three- and seven-planes. After giving a brief overview, we work out in detail an important consistency condition for String Theory constructions, the so-called tadpole cancellation condition, and we verify explicitly that chiral anomalies are cancelled via the generalised Green-Schwarz mechanism. The second topic is concerned with so-called D-brane instantons which are nonperturbative effects in type II String Theory constructions. We recall the instanton calculus for such configurations, we derive the so-called A eck-Dine-Seiberg superpotential in String Theory and we develop an important constraint, a chiral zero-mode constraint, for instanton contributions in the presence of a realistic Particle Physics sector. The third topic is about moduli stabilisation in type IIB string compactifications. More concretely, we review the so-called KKLT as well as Large Volume Scenario, and we construct and study a model for the latter scenario where the constraint mentioned above has been taken into account explicitly. Although the three topics studied in this thesis are slightly different in nature, there is nevertheless a complex interplay between them with many interrelations. In order to uncover these connections, a detailed study of each individual subject has been performed which has led to new results such as the chiral zero-mode constraint. (orig.)

  4. 21 CFR 201.323 - Aluminum in large and small volume parenterals used in total parenteral nutrition.

    Science.gov (United States)

    2010-04-01

    ... used in total parenteral nutrition. 201.323 Section 201.323 Food and Drugs FOOD AND DRUG ADMINISTRATION... parenteral nutrition. (a) The aluminum content of large volume parenteral (LVP) drug products used in total parenteral nutrition (TPN) therapy must not exceed 25 micrograms per liter (µg/L). (b) The package insert...

  5. Tenth annual coal preparation, utilization, and environmental control contractors conference: Proceedings. Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    1994-08-01

    Volume II contains papers presented at the following sessions: combustion 2000 session; advanced research and technology development session; commercial/industrial combustion systems session; alternative fuels utilization session; environmental control poster session; and advanced combustion technology poster session. Selected papers have been processed separately for inclusion in the Energy Science and Technology Database.

  6. Typical Scenario of Preparation, Implementation, and Aftershock Sequence of a Large Earthquake

    Science.gov (United States)

    Rodkin, Mikhail

    2016-04-01

    We have tried here to construct and examine the typical scenario of a large earthquake occurrence. The Harvard seismic moment GCMT catalog was used to construct the large earthquake generalized space-time vicinity (LEGV) and to investigate the seismicity behavior in LEGV. LEGV was composed of earthquakes falling into the zone of influence of any of the considerable number (100, 300, or 1,000) of largest earthquakes. The LEGV construction is aimed to enlarge the available statistics, diminish a strong random component, and to reveal in result the typical features of pre- and post-shock seismic activity in more detail. In result of the LEGV construction the character of fore- and aftershock cascades was examined in more detail than it was possible without of the use of the LEGV approach. It was shown also that the mean earthquake magnitude tends to increase, and the b-values, mean mb/mw ratios, apparent stress values, and mean depth tend to decrease. Amplitudes of all these anomalies increase with an approach to a moment of the generalized large earthquake (GLE) as a logarithm of time interval from GLE occurrence. Most of the discussed anomalies agree well with a common scenario of development of instability. Besides of such precursors of common character, one earthquake-specific precursor was found. The revealed decrease of mean earthquake depth during large earthquake preparation testifies probably for the deep fluid involvement in the process. The revealed in LEGV typical features of development of shear instability agree well with results obtained in laboratory acoustic emission (AE) study. Majority of the revealed anomalies appear to have a secondary character and are connected mainly with an increase in a mean earthquake magnitude in LEGV. The mean magnitude increase was shown to be connected mainly with a decrease of a portion of moderate size events (Mw 5.0 - 5.5) in a closer GLE vicinity. We believe that this deficit of moderate size events hardly can be

  7. Temperature monitoring in large volume spread footing foundations: case study "Parque da Cidade" - São Paulo

    Directory of Open Access Journals (Sweden)

    D. Couto

    Full Text Available ABSTRACT In recent years, the construction of foundation elements from large-volume reinforced concrete is becoming increasingly common. This implies a potential increase in the risk of cracks of thermal origin, due to the heat of hydration of cement. Under these circumstances, these concrete elements need to be treated using the mass concrete theory, widespread in dam construction, but little used when designing buildings. This paper aims to present a case study about the procedures and problems involved in the construction of a spread footing with a volume of approximately 800m³ designed for the foundation of a shopping center in São Paulo, Brazil.

  8. Influence of bone volume fraction and architecture on computed large-deformation failure mechanisms in human trabecular bone.

    Science.gov (United States)

    Bevill, Grant; Eswaran, Senthil K; Gupta, Atul; Papadopoulos, Panayiotis; Keaveny, Tony M

    2006-12-01

    Large-deformation bending and buckling have long been proposed as failure mechanisms by which the strength of trabecular bone can be affected disproportionately to changes in bone density, and thus may represent an important aspect of bone quality. We sought here to quantify the contribution of large-deformation failure mechanisms on strength, to determine the dependence of these effects on bone volume fraction and architecture, and to confirm that the inclusion of large-deformation effects in high-resolution finite element models improves predictions of strength versus experiment. Micro-CT-based finite element models having uniform hard tissue material properties were created from 54 cores of human trabecular bone taken from four anatomic sites (age = 70+/-11; 24 male, 27 female donors), which were subsequently biomechanically tested to failure. Strength predictions were made from the models first including, then excluding, large-deformation failure mechanisms, both for compressive and tensile load cases. As expected, strength predictions versus experimental data for the large-deformation finite element models were significantly improved (p deformation models in both tension and compression. Below a volume fraction of about 0.20, large-deformation failure mechanisms decreased trabecular strength from 5-80% for compressive loading, while effects were negligible above this volume fraction. Step-wise nonlinear multiple regression revealed that structure model index (SMI) and volume fraction (BV/TV) were significant predictors of these reductions in strength (R2 = 0.83, p deformation failure mechanisms on trabecular bone strength is highly heterogeneous and is not well explained by standard architectural metrics.

  9. Large 2D-arrays of size-controllable silver nanoparticles prepared by hybrid deposition

    Science.gov (United States)

    Dieu Thuy Ung, Thi; Hoa Nguyen, Thi; Liem Nguyen, Quang

    2016-09-01

    Two main results are presented in this paper. (i) Silver nanoparticles (AgNPs) with uniform size-distribution and controllability in the range of 20-50 nm were synthesized by seeding and growing at ambient conditions. The single-crystal Ag nano-seeds were created by reduction of AgNO3 in presence of citrate surfactant at 70 °C. Then, importantly, the fresh AgCl precursor was used in the presence of polyvinylpyrrolidone to adjust the reaction rate with ascorbic acid to generate Ag for growing on the surface of single-crystal Ag nano-seeds. The AgNPs size could be well-controlled by varying the amount of Ag nano-seeds while keeping the AgCl precursor concentration to be constant. (ii) The large 2D-arrays with homogeneous and dense monolayers of AgNPs were prepared on ITO substrates by hybrid method, in which the key technological point is the surface functionalization of AgNPs using mixed alkanethiols (dodecanethiol:octadecanethiol = 6:1). We have used the fabricated 2D-arrays from the 50 nm AgNPs as a surface enhanced Raman scattering substrate to take the Raman scattering spectra of rhodamine B (RhB), glucose and viral pathogen (H5N1) at very low concentrations of 10-10 M, 10-12 M and 4 ng μl-1, respectively.

  10. Thermally Sprayed Large Tubular Solid Oxide Fuel Cells and Its Stack: Geometry Optimization, Preparation, and Performance

    Science.gov (United States)

    Zhang, Shan-Lin; Li, Cheng-Xin; Liu, Shuai; Li, Chang-Jiu; Yang, Guan-Jun; He, Peng-Jiang; Yun, Liang-Liang; Song, Bo; Xie, Ying-Xin

    2017-02-01

    In this study, we develop a large tubular solid oxide fuel cells design with several cells in series on a porous cermet support, which has many characteristics such as self-sealing, low Ohmic loss, high strength, and good thermal expansion coefficient matching. Here, we investigate aspects of the cell design, manufacture, performance, and application. Firstly, the cell length and number of cells in series are optimized by theoretical analysis. Then, thermal spraying is applied as a cost-effective method to prepare all the cell components. Finally, the performance of different types of cells and two types of stacks is characterized. The maximum output power of one tube, which had 20 cells in series, reaches 31 and 40.5 W at 800 and 900 °C, respectively. Moreover, the output power of a stack assembled with 56 tubes, each with ten cells in series, reaches 800 W at 830 °C. The excellent single tube and cell stack performance suggest that thermally sprayed tubular SOFCs have significant potential for commercialized application.

  11. Preparation and Properties of the Heteropolyoxometalates of Large Organic Cation with Molybdotungstosilicic Acids

    Institute of Scientific and Technical Information of China (English)

    WANG Dunjia; FANG Zhengdong; WEI Xianhong

    2008-01-01

    Some new heteropolyoxometalates of large organic cations with molybdotungstosilicic acids (general formula: (CTMA)4SiMoxW12-xO40·mH20·nDMF, x=0,2,4,6,8,10,12) were prepared by the reaction of cetyltrimethylammonium bromide (CTMAB,C16H33N(CH3)3Br) with H4SiMoxW12-xO40(x=0,2,4,6,8,10,12)in aqueous solution and recrystallization in DMF, and characterized by elemental analysis, IR spectra,TG-DTA and XRD techniques. The IR spectrum confirms the presence of Keggin structure and organic cations in these compounds, and it is indicated that the stretching vibration of the M-Od, M-Ob-M and Si-Oa becomes more red-shifted when molybdenum is gradually substituted for the tungsten atom. In particular, the thermal decomposition of the heteropolyoxometalates was studied in nitrogen atmosphere. The TG-DTA curves show that their thermal behaviors not only contain the release of water molecule, DMF molecule, CTMA and its fragments but also contains simultaneous collapse of Keggin anion. Their end products of the thermal decomposition are the mixture of WO3, MoO3 and SiO2. And from the final decomposition temperature of view, it is found that the thermal stability of these compounds gradually is decreased when the number of molybdenum atoms is increased.

  12. Ultrafast and large scale preparation of superior catalyst for oxygen evolution reaction

    Science.gov (United States)

    Tian, Xianqing; Liu, Yunhua; Xiao, Dan; Sun, Jie

    2017-10-01

    The development of efficient and earth abundant catalyst for the oxygen evolution reaction (OER) is a key challenge for the renewable energy research community. Here, we report a facile and ultrafast route to immobilize nickel-iron layered double hydroxide (NiFe-LDH) nanoparticles on nickel foam (NF) via soaking the direct electroless deposited prussian blue analogue (PBA) on NF in 1 M KOH. This NiFe-LDH/NF electrode can be prepared in a few seconds without further treatments. It has three-dimensional interpenetrating network originated from its PBA precursor which facilitate the diffusion and ad/desorption of the reactants and producing for OER. And further characterization of the Faradaic efficiency and forced convection tests show direct evidence to demonstrate the formation of free intermediate(s) in the OER process. This electrode (typically NiFe-LDH-20s/NF) exhibits outstanding electrocatalytic activity with low overpotential of ∼0.240 V at 10 mA cm-2, low Tafel slope of 38 mV dec-1, and great stability. This feasible strategy affords a new strategy for the large scale manufacture of low-cost, effective and robust OER electrodes.

  13. Thermally Sprayed Large Tubular Solid Oxide Fuel Cells and Its Stack: Geometry Optimization, Preparation, and Performance

    Science.gov (United States)

    Zhang, Shan-Lin; Li, Cheng-Xin; Liu, Shuai; Li, Chang-Jiu; Yang, Guan-Jun; He, Peng-Jiang; Yun, Liang-Liang; Song, Bo; Xie, Ying-Xin

    2017-01-01

    In this study, we develop a large tubular solid oxide fuel cells design with several cells in series on a porous cermet support, which has many characteristics such as self-sealing, low Ohmic loss, high strength, and good thermal expansion coefficient matching. Here, we investigate aspects of the cell design, manufacture, performance, and application. Firstly, the cell length and number of cells in series are optimized by theoretical analysis. Then, thermal spraying is applied as a cost-effective method to prepare all the cell components. Finally, the performance of different types of cells and two types of stacks is characterized. The maximum output power of one tube, which had 20 cells in series, reaches 31 and 40.5 W at 800 and 900 °C, respectively. Moreover, the output power of a stack assembled with 56 tubes, each with ten cells in series, reaches 800 W at 830 °C. The excellent single tube and cell stack performance suggest that thermally sprayed tubular SOFCs have significant potential for commercialized application.

  14. Preparation and characterization of mixed hydroxy-Fe-Al pillared montmorillonite with large basal spacing

    Institute of Scientific and Technical Information of China (English)

    ZENG Xiu-qiong; LIU Wei-ping

    2004-01-01

    Mixed hydroxy-Al-Fe pillared montmorillonites with large basal spacing were successfully prepared through cation-exchanging of Na+ - montmorillonite with mixed hydroxy-Al and hydroxy-Fe pillaring solutions made from hydrolysis of corresponding metal salts, followed by calcination to convert hydroxy-Al and hydroxy-Fe into intercalated polycations. According to XRD analysis, the basal spacing d(001 ) of pillared products dramatically enlarged from 12.7 A in the Na-montmorillonite to 81 A in the hydroxy-Fe -montmorillonite and 77.5 A in mixed hydroxy-Al-Fe-montmorillonite. The N2 BET surface areas of the pillared montmorillonites also greatly increased to more than 200m2/g as compared to about 27 m2/g for the Na-montmorillonite. IR analysis of hydroxy-Fe, and mixed hydroxy-Al-Fe pillared montmorillonites revealed a new absorption vibration at 1384 cm-1 wavelength. XRF elemental analysis data also showed a high content of Fe2 O3 in the hydroxy-Fe pillared montmorillonite.

  15. Preparation

    Directory of Open Access Journals (Sweden)

    M.M. Dardir

    2014-03-01

    Full Text Available Some hexanamide-mono and di-linoleniate esters were prepared by the reaction of linolenic acid and hexanamide (derived from the reaction of hexanoic acid and diethanolamine. The chemical structure for the newly prepared hexanamide-mono and di-linoleniate esters were elucidated using elemental analysis, (FTIR, H 1NMR and chemical ionization mass spectra (CI/Ms spectroscopic techniques. The results of the spectroscopic analysis indicated that they were prepared through the right method and they have high purity. The new prepared esters have high biodegradability and lower toxicity (environmentally friendly so they were evaluated as a synthetic-based mud (ester-based mud for oil-well drilling fluids. The evaluation included study of the rheological properties, filtration and thermal properties of the ester based-muds formulated with the newly prepared esters compared to the reference commercial synthetic-based mud.

  16. Preparation of small volume, leuko and erythrocyte very poor platelet concentrates.

    Science.gov (United States)

    Valbonesi, M; Angelini, G; Malfanti, L; Lercari, G; Fella, M; Calderisi, S; Anselmo, A; Balistreri, M

    1986-05-01

    Recently developed automated discontinuous flow centrifuge (DFC) separators can produce leuko- and erythrocyte-poor platelet concentrates (PC). According to general experience with these machines it is difficult to obtain more than 4 X 10(11) platelets, though a second program set up by Coffe et al. appears to produce PC containing approximately 5 X 10(11) platelets suspended in a plasma volume of 390 ml. At our center we employed a new Dideco cell separator equipped with the surge pump and a technique developed for the production of small volume, RBC and WBC-very poor PC. In 60 routine procedures we obtained the following results: mean processing time 87 +/- 11 minutes; final volume of PC 136 +/- 19 ml, with a mean platelet yield of 5.21 X 10(11) platelets. WBC contamination was 1.8 X 10(8) (93% lymphocytes) and RBC were 3.1 X 10(8). Plasma volume as well as WBC and RBC contamination were reduced by recirculating PC after the 6th pass. The demand for single donor platelet concentrates (PC) is increasing progressively. Recently developed automated cell separators can produce leukocyte (WBC) and erythrocyte (RBC) poor PC. With these machines it may be difficult to obtain PC containing at least 4 X 10(11) platelets and less than 1 X 10(9) leukocytes (1, 2, 3) since donor variables such as hematocrit, precounts, buffy coat formation and initial plasma light transmission are of paramount importance for the efficiency of the program. At our center a prototype discontinuous flow centrifuge (DFC) cell separator equipped with the surge pump was studied.(ABSTRACT TRUNCATED AT 250 WORDS)

  17. Systems and methods for the detection of low-level harmful substances in a large volume of fluid

    Science.gov (United States)

    Carpenter, Michael V.; Roybal, Lyle G.; Lindquist, Alan; Gallardo, Vincente

    2016-03-15

    A method and device for the detection of low-level harmful substances in a large volume of fluid comprising using a concentrator system to produce a retentate and analyzing the retentate for the presence of at least one harmful substance. The concentrator system performs a method comprising pumping at least 10 liters of fluid from a sample source through a filter. While pumping, the concentrator system diverts retentate from the filter into a container. The concentrator system also recirculates at least part of the retentate in the container again through the filter. The concentrator system controls the speed of the pump with a control system thereby maintaining a fluid pressure less than 25 psi during the pumping of the fluid; monitors the quantity of retentate within the container with a control system, and maintains a reduced volume level of retentate and a target volume of retentate.

  18. Detection of triazole deicing additives in soil samples from airports with low, mid, and large volume aircraft deicing activities.

    Science.gov (United States)

    McNeill, K S; Cancilla, D A

    2009-03-01

    Soil samples from three USA airports representing low, mid, and large volume users of aircraft deicing fluids (ADAFs) were analyzed by LC/MS/MS for the presence of triazoles, a class of corrosion inhibitors historically used in ADAFs. Triazoles, specifically the 4-methyl-1H-benzotriazole and the 5-methyl-1H-benzotriazole, were detected in a majority of samples and ranged from 2.35 to 424.19 microg/kg. Previous studies have focused primarily on ground and surface water impacts of larger volume ADAF users. The detection of triazoles in soils at low volume ADAF use airports suggests that deicing activities may have a broader environmental impact than previously considered.

  19. Influence of concentration and volume of precursor on the electrochemical properties of vanadium oxide thin films prepared by spray pyrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Ingole, R. S.; Fugare, B. Y.; Lokhande, B. J., E-mail: bjlokhande@yahoo.com [School of Physical Sciences, Solapur University, Solapur 413 255, M.S. (India)

    2016-04-13

    Vanadium oxide (V{sub 2}O{sub 5}) thin films have been prepared by spray pyrolysis using different concentrations and volumes of precursor solution via aqueous route at 673K deposition temperature. The influences of concentration and volume on the structural, morphological and electrochemical properties of the deposited samples are studied well. X - ray diffraction study shows orthorhombic crystal structure with V{sub 2}O{sub 5} phase, confirmed by FTIR spectroscopy. Scanning electron microscopy shows granular, homogeneous and dense surface morphology. Cyclic voltammetery of all samples carried at all scan rates. Samples prepared using 0.05M, 40 ml of precursor solution shows highest specific capacitance 428.25 F/gm at 5 mV/s, Charge discharge behavior exhibits specific energy 18.73 Wh/kg, specific power 36.00 kW/kg, columbic efficiency 87.50 %. Impedance spectroscopy study was carried in the frequency range 1mHz – 1MHz, reveals pseudocapacitive behavior of the electrode exhibiting internal resistance 1.34 ohm.

  20. Fused silica capillaries with two segments of different internal diameters and inner surface roughnesses prepared by etching with supercritical water and used for volume coupling electrophoresis.

    Science.gov (United States)

    Horká, Marie; Karásek, Pavel; Roth, Michal; Šlais, Karel

    2017-02-22

    In this work, single-piece fused silica capillaries with two different internal diameter segments featuring different inner surface roughness were prepared by new etching technology with supercritical water and used for volume coupling electrophoresis. The concept of separation and online pre-concentration of analytes in high conductivity matrix is based on the online large-volume sample pre-concentration by the combination of transient isotachophoretic stacking and sweeping of charged proteins in micellar electrokinetic chromatography using non-ionogenic surfactant. The modified surface roughness step helped to the significant narrowing of the zones of examined analytes. The sweeping and separating steps were accomplished simultaneously by the use of phosphate buffer (pH 7) containing ethanol, non-ionogenic surfactant Brij 35, and polyethylene glycol (PEG 10000) after sample injection. Sample solution of a large volume (maximum 3.7 μL) dissolved in physiological saline solution was injected into the wider end of capillary with inlet inner diameter from 150, 185 or 218 μm. The calibration plots were linear (R(2) ∼ 0.9993) over a 0.060-1 μg/mL range for the proteins used, albumin and cytochrome c. The peak area RSDs from at least 20 independent measuremens were below 3.2%. This online pre-concentration technique produced a more than 196-fold increase in sensitivity, and it can be applied for detection of, e.g. the presence of albumin in urine (0.060 μg/mL).

  1. Development of deployable structures for large space platforms. Volume 2: Design development

    Science.gov (United States)

    Greenberg, H. S.

    1983-01-01

    Design evolution, test article design, test article mass properties, and structural analysis of deployable platform systems are discussed. Orbit transfer vehicle (OTV) hangar development, OTV hangar concept selection, and manned module development are discussed. Deployable platform systems requirements, material data base, technology development needs, concept selection and deployable volume enclosures are also discussed.

  2. Determination of Atto- to Femtogram Levels of Americium and Curium Isotopes in Large-Volume Urine Samples by Compact Accelerator Mass Spectrometry.

    Science.gov (United States)

    Dai, Xiongxin; Christl, Marcus; Kramer-Tremblay, Sheila; Synal, Hans-Arno

    2016-03-01

    Ultralow level analysis of actinides in urine samples may be required for dose assessment in the event of internal exposures to these radionuclides at nuclear facilities and nuclear power plants. A new bioassay method for analysis of sub-femtogram levels of Am and Cm in large-volume urine samples was developed. Americium and curium were co-precipitated with hydrous titanium oxide from the urine matrix and purified by column chromatography separation. After target preparation using mixed titanium/iron oxides, the final sample was measured by compact accelerator mass spectrometry. Urine samples spiked with known quantities of Am and Cm isotopes in the range of attogram to femtogram levels were measured for method evaluation. The results are in good agreement with the expected values, demonstrating the feasibility of compact accelerator mass spectrometry (AMS) for the determination of minor actinides at the levels of attogram/liter in urine samples to meet stringent sensitivity requirements for internal dosimetry assessment.

  3. Fabrics, Facies And Flow Through A Large-Volume Ignimbrite: Pampa De Oxaya, Chile.

    Science.gov (United States)

    Platzman, Ellen; Cooper, Frances

    2016-04-01

    Large volume pyroclastic currents form during some of the most destructive volcanic eruptions on the planet, yet because they are underrepresented in the geological record they remain poorly understood. The Miocene Oxaya ignimbrites, exposed along the western Andean slopes in northern Chile, form one of the largest ignimbrite provinces on earth. We use anisotropy of magnetic susceptibility (AMS) in conjunction with rock magnetic measurements to investigate flow behavior and depositional processes in one of the largest members of the Oxaya succession, the Cardones ignimbrite. Despite its prominence the location of the source caldera remains unknown and fundamental processes remain poorly constrained. During 2012 nearly 8km (7,773m) of core was recovered from the early Miocene ignimbrites in 11 holes at elevations ranging from 2336m to 3805m along the Andean escarpment east of Arica, Chile. The drill cores are remarkable in that they penetrate through the entirety of the ignimbrite sequence and into the basement below. Samples for this study were collected from a > 1 km long core drilled at an altitude 3692m. The core sampled 981 m of Cardones ignimbrite and 15 m of underlying sediments and volcaniclastics before penetrating 148 m of basement. Detailed measurements of the variation in bulk magnetic properties including natural remanent magnetization (NRM), susceptibility, ARM, and IRM, were used to monitor changes in concentration, composition and grainsize of the magnetic components though the ignimbrite. AMS in conjunction with detailed rock magnetic measurements were used to constrain flow processes. The data reveal a well-defined flow direction and systematic variations in flow processes with depth. Low field bulk magnetic susceptibility averages 3.2x10-3 SI. Rock magnetic studies and petrographic examination indicate that magnetite is likely to be the dominant magnetic phase although paramagnetic mineral phases also contribute to the magnetic fabric. The degree

  4. Patient-specific quality assurance for spot scanning proton beams using a large-volume liquid scintillator detector

    Science.gov (United States)

    Robertson, D.; Beddar, S.

    2017-05-01

    A large-volume liquid scintillator detector was used to measure individual energy layers from a clinical prostate treatment plan on a scanning proton beam system. Lateral and beam’s-eye view images of the dose distribution were acquired with two CCD cameras facing adjacent sides of a scintillator tank. The measured dose images were compared with calculated dose distributions from a validated Monte Carlo model. The measured and calculated dose distributions showed good agreement, with the exception of the Bragg peak region of the lateral view, which exhibited ionization quenching. The beam’s-eye and lateral views achieved gamma analysis passing rates of 99.7% and 92.5%, respectively, using gamma criteria of 3%, 3 mm. Large-volume scintillator detectors show promise for quick and accurate measurements of patient treatment fields for scanning proton beam systems.

  5. Distribution of Large Volume Image Data Using the Mixed Mode of Java Servlet and COM on Web

    Institute of Scientific and Technical Information of China (English)

    WANG Mi; ZHU Xinyan; PAN Jun; CHEN Nengcheng

    2004-01-01

    This paper reports some researches on distribution of large volume image data using techniques of the Mixed Mode of Java Servlet and COM on Web. The architecture and key technologies are discussed in detail. The web distribution system of image is implemented and the system is tested by the application instances. At last, the advantages and disadvantages for this web image distribution mode are analyzed.

  6. Preparation and development of land use energy consumption data sets. Volume 1, phase 1. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1978-12-20

    An analysis was made of the potential usefulness of land-use-related data, the availability of relevant information in the literature, and potential approaches for data collection. This volume describes the results of the analysis, while Volume II contains technical backup materials. Chapter 2 discusses the issue of community classification: questions of classification and aggregation have been the most significant technical issues faced on the project, since they strongly affect the accuracy and usefulness of any data that are developed. Chapter 3 is concerned with consistency of accounting, primarily in the measurement of energy use. Transportation patterns, energy-transmission losses, and energy embodied in materials and structure can all be assigned to various land uses in a number of ways, and it is important to perform the assignment in a way that is valuable for the policies being evaluated. Thus, Chapter 3 forms the structure for the dependent variables of the system: the various types and patterns of energy use, while Chapter 2 describes the structure of the independent variables, which are the land-use patterns described, plus other factors such as climate. Chapter 4 takes these two structures and presents computations of energy use for the various patterns of land uses, based on the literature, and Chapter 5 discusses the implications of these analyses for energy planning. This leads directly to Chapter 6, where recommendations are made regarding both data collection and use of existing data. (MCW)

  7. Design and Analysis of A Beacon-Less Routing Protocol for Large Volume Content Dissemination in Vehicular Ad Hoc Networks.

    Science.gov (United States)

    Hu, Miao; Zhong, Zhangdui; Ni, Minming; Baiocchi, Andrea

    2016-11-01

    Large volume content dissemination is pursued by the growing number of high quality applications for Vehicular Ad hoc NETworks(VANETs), e.g., the live road surveillance service and the video-based overtaking assistant service. For the highly dynamical vehicular network topology, beacon-less routing protocols have been proven to be efficient in achieving a balance between the system performance and the control overhead. However, to the authors' best knowledge, the routing design for large volume content has not been well considered in the previous work, which will introduce new challenges, e.g., the enhanced connectivity requirement for a radio link. In this paper, a link Lifetime-aware Beacon-less Routing Protocol (LBRP) is designed for large volume content delivery in VANETs. Each vehicle makes the forwarding decision based on the message header information and its current state, including the speed and position information. A semi-Markov process analytical model is proposed to evaluate the expected delay in constructing one routing path for LBRP. Simulations show that the proposed LBRP scheme outperforms the traditional dissemination protocols in providing a low end-to-end delay. The analytical model is shown to exhibit a good match on the delay estimation with Monte Carlo simulations, as well.

  8. Axial vascularization of a large volume calcium phosphate ceramic bone substitute in the sheep AV loop model.

    Science.gov (United States)

    Beier, Justus P; Horch, Raymund E; Hess, Andreas; Arkudas, Andreas; Heinrich, Johanna; Loew, Johanna; Gulle, Heinz; Polykandriotis, Elias; Bleiziffer, Oliver; Kneser, Ulrich

    2010-03-01

    Vascularization still remains an obstacle to engineering of bone tissue with clinically relevant dimensions. Our aim was to induce axial vascularization in a large volume of a clinically approved biphasic calcium phosphate ceramic by transferring the arteriovenous (AV) loop approach to a large animal model. HA/beta-TCP granula were mixed with fibrin gel for a total volume of 16 cm(3), followed by incorporation into an isolation chamber together with an AV loop. The chambers were implanted into the groins of merino sheep and the development of vascularization was monitored by sequential non-invasive magnetic resonance imaging (MRI). The chambers were explanted after 6 and 12 weeks, the pedicle was perfused with contrast agent and specimens were subjected to micro-computed tomography (micro-CT) scan and histological analysis. Sequential MRI demonstrated a significantly increased perfusion in the HA/beta-TCP matrices over time. Micro-CT scans and histology confirmed successful axial vascularization of HA/beta-TCP constructs. This study demonstrates, for the first time, successful axial vascularization of a clinically approved bone substitute with a significant volume in a large animal model by means of a microsurgically created AV loop, thus paving the way for the first microsurgical transplantation of a tissue-engineered, axially vascularized bone with clinically relevant dimensions.

  9. Genetic influences on schizophrenia and subcortical brain volumes: large-scale proof of concept.

    Science.gov (United States)

    Franke, Barbara; Stein, Jason L; Ripke, Stephan; Anttila, Verneri; Hibar, Derrek P; van Hulzen, Kimm J E; Arias-Vasquez, Alejandro; Smoller, Jordan W; Nichols, Thomas E; Neale, Michael C; McIntosh, Andrew M; Lee, Phil; McMahon, Francis J; Meyer-Lindenberg, Andreas; Mattheisen, Manuel; Andreassen, Ole A; Gruber, Oliver; Sachdev, Perminder S; Roiz-Santiañez, Roberto; Saykin, Andrew J; Ehrlich, Stefan; Mather, Karen A; Turner, Jessica A; Schwarz, Emanuel; Thalamuthu, Anbupalam; Yao, Yin; Ho, Yvonne Y W; Martin, Nicholas G; Wright, Margaret J; O'Donovan, Michael C; Thompson, Paul M; Neale, Benjamin M; Medland, Sarah E; Sullivan, Patrick F

    2016-03-01

    Schizophrenia is a devastating psychiatric illness with high heritability. Brain structure and function differ, on average, between people with schizophrenia and healthy individuals. As common genetic associations are emerging for both schizophrenia and brain imaging phenotypes, we can now use genome-wide data to investigate genetic overlap. Here we integrated results from common variant studies of schizophrenia (33,636 cases, 43,008 controls) and volumes of several (mainly subcortical) brain structures (11,840 subjects). We did not find evidence of genetic overlap between schizophrenia risk and subcortical volume measures either at the level of common variant genetic architecture or for single genetic markers. These results provide a proof of concept (albeit based on a limited set of structural brain measures) and define a roadmap for future studies investigating the genetic covariance between structural or functional brain phenotypes and risk for psychiatric disorders.

  10. Gravitational search for cryptovolcanism on the Moon: Evidence for large volumes of early igneous activity

    Science.gov (United States)

    Sori, Michael M.; Zuber, Maria T.; Head, James W.; Kiefer, Walter S.

    2016-07-01

    We define lunar cryptovolcanism as volcanic deposits on the Moon hidden by overlying material. Notably, cryptovolcanism includes both cryptomaria (subsurface extrusive basaltic deposits that are obscured by overlying higher albedo basin and crater ejecta) and earlier candidate extrusives, such as the Mg-suite. Knowledge of the volume and extent of cryptovolcanism is necessary for a comprehensive understanding of lunar volcanic history, particularly in early (pre 3.8 Ga) epochs when abundant impact craters and basins obscured surface volcanic deposits by lateral emplacement of ejecta. We use Gravity Recovery and Interior Laboratory (GRAIL) gravity and Lunar Orbiter Laser Altimeter (LOLA) topography data to construct maps of the Moon's positive Bouguer and isostatic gravity anomalies, and explore the possibility that these features are due to mass excesses associated with cryptovolcanism by cross-referencing the regions with geologic data such as dark halo craters. We model the potential cryptovolcanic deposits as buried high-density rectangular prisms at depth in the upper crust, and find a volume of candidate buried cryptovolcanism between 0.4 × 106 km3 and 4.8 × 106 km3, depending on assumptions about density and crustal compensation state. These candidate deposits correspond to a surface area of between 0.50 × 106 km2 and 1.14 × 106 km2, which would increase the amount of the lunar surface containing volcanic deposits from 16.6% to between 17.9% and 19.5%. The inferred volume of cryptovolcanism is comparable to the smallest estimates of the volume of visible mare basalts and up to ∼50% of the largest estimates; the high-resolution GRAIL and LOLA observations thus would collectively indicate that early (pre 3.8 Ga) lunar volcanism is an important element of lunar thermal evolution. Alternatively, the buried material could represent the presence of intrusive Mg-suite sills or plutons.

  11. Ground Organic Monolith Particles Having a Large Volume of Macropores as Chromatographic Separation Media

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jin Wook; Ali, Faiz; Kim, Yune Sung; Cheong, Won Jo [Inha Univ., Incheon (Korea, Republic of)

    2014-07-15

    A reaction mixture was developed for formation of soft organic monolith that was easily smashed, rinsed, refluxed, filtered, and dried to give monolith particles having high pore volume of macropores. This phase was almost without mesopores. The reaction mixture was composed of methacrylic acid, ethylene glycol dimethacrylate, polyethylene glycol (porogen), and an initiator in a mixed solvent of toluene and isooctane. The selection of porogen and its amount was carefully carried out to obtain the optimized separation efficiency of the resultant phase. The median macropore size was 1.6 μm, and the total pore volume was 3.0-3.4 mL/g. The median particle size (volume based) was 15 μm, and the range of particle size distribution was very broad. Nevertheless the column (1 Χ 300 mm) packed with this phase showed good separation efficiency (N∼10,000-16,000) comparable to that of a commercial column packed with 5 μm C18 silica particles.

  12. A 3D time reversal cavity for the focusing of high-intensity ultrasound pulses over a large volume

    Science.gov (United States)

    Robin, J.; Arnal, B.; Tanter, M.; Pernot, M.

    2017-02-01

    Shock wave ultrasound therapy techniques, increasingly used for non-invasive surgery, require extremely high pressure amplitudes in precise focal spots, and large high-power transducers arranged on a spherical shell are usually used to achieve that. This solution allows limited steering of the beam around the geometrical focus of the device at the cost of a large number of transducer elements, and the treatment of large and moving organs like the heart is challenging or impossible. This paper validates numerically and experimentally the possibility of using a time reversal cavity (TRC) for the same purpose. A 128-element, 1 MHz power transducer combined with different multiple scattering media in a TRC was used. We were able to focus high-power ultrasound pulses over a large volume in a controlled manner, with a limited number of transducer elements. We reached sufficiently high pressure amplitudes to erode an Ultracal® target over a 10 cm2 area.

  13. Rapid specimen preparation to improve the throughput of electron microscopic volume imaging for three-dimensional analyses of subcellular ultrastructures with serial block-face scanning electron microscopy.

    Science.gov (United States)

    Thai, Truc Quynh; Nguyen, Huy Bang; Saitoh, Sei; Wu, Bao; Saitoh, Yurika; Shimo, Satoshi; Elewa, Yaser Hosny Ali; Ichii, Osamu; Kon, Yasuhiro; Takaki, Takashi; Joh, Kensuke; Ohno, Nobuhiko

    2016-09-01

    Serial block-face imaging using scanning electron microscopy enables rapid observations of three-dimensional ultrastructures in a large volume of biological specimens. However, such imaging usually requires days for sample preparation to reduce charging and increase image contrast. In this study, we report a rapid procedure to acquire serial electron microscopic images within 1 day for three-dimensional analyses of subcellular ultrastructures. This procedure is based on serial block-face with two major modifications, including a new sample treatment device and direct polymerization on the rivets, to reduce the time and workload needed. The modified procedure without uranyl acetate can produce tens of embedded samples observable under serial block-face scanning electron microscopy within 1 day. The serial images obtained are similar to the block-face images acquired by common procedures, and are applicable to three-dimensional reconstructions at a subcellular resolution. Using this approach, regional immune deposits and the double contour or heterogeneous thinning of basement membranes were observed in the glomerular capillary loops of an autoimmune nephropathy model. These modifications provide options to improve the throughput of three-dimensional electron microscopic examinations, and will ultimately be beneficial for the wider application of volume imaging in life science and clinical medicine.

  14. A novel porous bioceramics scaffold by accumulating hydroxyapatite spherulites for large bone tissue engineering in vivo. II. Construct large volume of bone grafts.

    Science.gov (United States)

    Zhi, Wei; Zhang, Cong; Duan, Ke; Li, Xiaohong; Qu, Shuxin; Wang, Jianxin; Zhu, Zhuoli; Huang, Peng; Xia, Tian; Liao, Ga; Weng, Jie

    2014-08-01

    In vivo engineering of bone autografts using bioceramic scaffolds with appropriate porous structures is a potential approach to prepare autologous bone grafts for the repair of critical-sized bone defects. This study investigated the evolutionary process of osteogenesis, angiogenesis, and compressive strength of bioceramic scaffolds implanted in two non-osseous sites of dogs: the abdominal cavity and the dorsal muscle. Hydroxyapatite (HA) sphere-accumulated scaffolds with controlled porous structures were prepared and placed in the two sites for up to 6 months. Analyses of retrieved scaffolds found that osteogenesis and angiogenesis were faster in scaffolds implanted in dorsal muscles compared with those placed in abdominal cavities. The abdominal cavity, however, can accommodate larger bone grafts with designed shape. Analyses of scaffolds implanted in abdominal cavities [an environment of a low mesenchymal stem cell (MSC) density] further demonstrated that angiogenesis play critical roles during osteogenesis in the scaffolds, presumably by supplying progenitor cells and/or MSCs as seed cells. This study also examined the relationship between the volume of bone grafts and the physiological environment of in vivo bioreactor. These results provide basic information for the selection of appropriate implanting sites and culture time required to engineer autologous bone grafts for the clinical bone defect repair. Based on these positive results, a pilot study has applied the grafts constructed in canine abdominal cavity to repair segmental bone defect in load-bearing sites (limbs).

  15. Large-Scale Context-Aware Volume Navigation using Dynamic Insets

    KAUST Repository

    Al-Awami, Ali

    2012-07-01

    Latest developments in electron microscopy (EM) technology produce high resolution images that enable neuro-scientists to identify and put together the complex neural connections in a nervous system. However, because of the massive size and underlying complexity of this kind of data, processing, navigation and analysis suffer drastically in terms of time and effort. In this work, we propose the use of state-of- the-art navigation techniques, such as dynamic insets, built on a peta-scale volume visualization framework to provide focus and context-awareness to help neuro-scientists in their mission to analyze, reconstruct, navigate and explore EM neuroscience data.

  16. Ultrastructurally smooth thick partitioning and volume stitching for large-scale connectomics.

    Science.gov (United States)

    Hayworth, Kenneth J; Xu, C Shan; Lu, Zhiyuan; Knott, Graham W; Fetter, Richard D; Tapia, Juan Carlos; Lichtman, Jeff W; Hess, Harald F

    2015-04-01

    Focused-ion-beam scanning electron microscopy (FIB-SEM) has become an essential tool for studying neural tissue at resolutions below 10 nm × 10 nm × 10 nm, producing data sets optimized for automatic connectome tracing. We present a technical advance, ultrathick sectioning, which reliably subdivides embedded tissue samples into chunks (20 μm thick) optimally sized and mounted for efficient, parallel FIB-SEM imaging. These chunks are imaged separately and then 'volume stitched' back together, producing a final three-dimensional data set suitable for connectome tracing.

  17. Construction of Large-Volume Tissue Mimics with 3D Functional Vascular Networks

    Science.gov (United States)

    Kang, Tae-Yun; Hong, Jung Min; Jung, Jin Woo; Kang, Hyun-Wook; Cho, Dong-Woo

    2016-01-01

    We used indirect stereolithography (SL) to form inner-layered fluidic networks in a porous scaffold by introducing a hydrogel barrier on the luminal surface, then seeded the networks separately with human umbilical vein endothelial cells and human lung fibroblasts to form a tissue mimic containing vascular networks. The artificial vascular networks provided channels for oxygen transport, thus reducing the hypoxic volume and preventing cell death. The endothelium of the vascular networks significantly retarded the occlusion of channels during whole-blood circulation. The tissue mimics have the potential to be used as an in vitro platform to examine the physiologic and pathologic phenomena through vascular architecture. PMID:27228079

  18. Construction of Large-Volume Tissue Mimics with 3D Functional Vascular Networks.

    Directory of Open Access Journals (Sweden)

    Tae-Yun Kang

    Full Text Available We used indirect stereolithography (SL to form inner-layered fluidic networks in a porous scaffold by introducing a hydrogel barrier on the luminal surface, then seeded the networks separately with human umbilical vein endothelial cells and human lung fibroblasts to form a tissue mimic containing vascular networks. The artificial vascular networks provided channels for oxygen transport, thus reducing the hypoxic volume and preventing cell death. The endothelium of the vascular networks significantly retarded the occlusion of channels during whole-blood circulation. The tissue mimics have the potential to be used as an in vitro platform to examine the physiologic and pathologic phenomena through vascular architecture.

  19. Study of Large-Scale Aluminium-Doped Zinc Oxide Ceramic Targets Prepared by Slip Casting

    Directory of Open Access Journals (Sweden)

    Ling-yun Han

    2016-01-01

    Full Text Available Aluminium-doped zinc oxide (AZO ceramic green compacts at a size of 170 × 340 × 17 mm have been prepared by slip casting. An AZO slurry with good fluidity and viscosity was obtained when 1.2 wt% of dispersant was added, which indicates that the slurry prepared with micrometre particles is more suitable for slip casting. The densification and electrical properties of the AZO targets prepared by particles with different sizes were investigated after sintering from 1380 to 1460°C. The results showed that the relative density of the AZO target prepared with 45 nm particles could reach nearly 98% at 1380°C; the resistivity of the AZO target prepared with nanometre particles could be as low as 1.6 × 10−3 Ω·cm at 1400°C; and the average transmittance of the AZO film prepared with nanometre particles could reach a maximum value of 93.73% in the visible region at 250 W. In this study, the correlation between the density, resistivity, and grain growth of AZO ceramic green compacts was studied.

  20. Underground low flux neutron background measurements in LSM using a large volume (1m3) spherical proportional counter

    Science.gov (United States)

    Savvidis, I.; Giomataris, I.; Bougamont, E.; Irastorza, I.; Aune, S.; Chapelier, M.; Charvin, P. H.; Colas, P.; Derre, J.; Ferrer, E.; Gerbier, G.; Gros, M.; Mangier, P.; Navick, X. F.; Salin, P.; Vergados, J. D.; Zampalo, M.

    2010-01-01

    A large volume (1m3) spherical proportional counter has been developed at CEA/Saclay, for low flux neutron measurements. The high voltage is applied to a small sphere 15mm in diameter, located in the center of the counter and the wall of the counter is grounded. Neutrons can be measured successfully, with high sensitivity, using 3He gas in the detector. The proton and tritium energy deposition in the drift gaseous volume, from the reaction 3He(n,p)3H, can provide the neutron spectra from thermal neutrons up to several MeV. The detector has been installed in the underground laboratory in Modane (LSM) to measure the neutron background. The sphere has been has been filled with gas mixture of Ar + 2% CH4 +3gr He-3, at 275 mbar. The thermal neutron peak is well separated from the cosmic ray and gamma background, permitting of neutron flux calculation. Other potential applications requiring large volume of about 10 m in radius are described in detail in reference

  1. Nuclear waste calorimeter for very large drums with 385 litres sample volume

    Energy Technology Data Exchange (ETDEWEB)

    Jossens, G.; Mathonat, C. [SETARAM Instrumentation, Caluire (France); Bachelet, F. [CEA Valduc, Is sur Tille (France)

    2015-03-15

    Calorimetry is a very precise and well adapted tool for the classification of drums containing nuclear waste material depending on their level of activities (low, medium, high). A new calorimeter has been developed by SETARAM Instrumentation and the CEA Valduc in France. This new calorimeter is designed for drums having a volume bigger than 100 liters. It guarantees high operator safety by optimizing drum handling and air circulation for cooling, and optimized software for direct measurement of the quantity of nuclear material. The LVC1380 calorimeter makes it possible to work over the range 10 to 3000 mW, which corresponds to approximately 0.03 to 10 g of tritium or 3 to 955 g of {sup 241}Pu in a volume up to 385 liters. This calorimeter is based on the heat flow measurement using Peltier elements which surround the drum in the 3 dimensions and therefore measure all the heat coming from the radioactive stuff whatever its position inside the drum. Calorimeter's insulating layers constitute a thermal barrier designed to filter disturbances until they represent less than 0.001 Celsius degrees and to eliminate long term disturbances associated, for example, with laboratory temperature variations between day and night. A calibration device based on Joule effect has also been designed. Measurement time has been optimized but remains long compared with other methods of measurement such as gamma spectrometry but its main asset is to have a good accuracy for low level activities.

  2. Paul Scherrer Institute Scientific and Technical Report 1999. Volume VI: Large Research Facilities

    Energy Technology Data Exchange (ETDEWEB)

    Foroughi, Fereydoun; Bercher, Renate; Buechli, Carmen; Meyer, Rosa [eds.

    2000-07-01

    The department GFA (Grossforschungsanlagen, Large Research Facilities) has been established in October 1998. Its main duty is operation, maintenance and development of the PSI accelerators, the spallation neutron source and the beam transport systems for pions and muons. A large effort of this group concerns the planning and co-ordination of new projects like e.g. the assembly of the synchrotron light source (SLS), design studies of a new proton therapy facility, the ultracold neutron source and a new intensive secondary beam line for low energy muons. A large fraction of this report is devoted to research especially in the field of materials Science. The studies include large scale molecular dynamics computer simulations on the elastic and plastic behavior of nanostructured metals, complemented by experimental mechanical testing using micro-indentation and miniaturized tensile testing, as well as microstructural characterisation and strain field mapping of metallic coatings and thin ceramic layers, the latter done with synchrotron radiation.

  3. Paul Scherrer Institute Scientific Report 1998. Volume VI: Large Research Facilities

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, Guenter; Bercher, Renate; Buechli, Carmen; Foroughi, Fereydoun; Meyer, Rosa [eds.

    1999-09-01

    The department GFA (Grossforschungsanlagen, Large Research Facilities) has been established in October 1998 and its main duty is operation, maintenance and development of the PSI accelerators, the spallation neutron source and the beam transport systems for pions and muons. A large effort of this group concerns the planning and co-ordination of the assembly of the Swiss Light Source (SLS). (author) figs., tabs., refs.

  4. Distributed location-based query processing on large volumes of moving items

    Institute of Scientific and Technical Information of China (English)

    JEON Se-gil; LEE Chung-woo; NAH Yunmook; KIM Moon-hae; HAN Ki-joon

    2004-01-01

    Recently, new techniques to efficiently manage current and past location information of moving objects have received significant interests in the area of moving object databases and location-based service systems. In this paper, we exploit query processing schemes for location management systems, which consist of multiple data processing nodes to handle massive volume of moving objects such as cellular phone users.To show the usefulness of the proposed schemes, some experimental results showing performance factors regarding distributed query processing are explained. In our experiments, we use two kinds of data set: one is generated by the extended GSTD simulator and another is generated by the real-time data generator which generates location sensing reports of various types of users having different movement patterns.

  5. Enrichment of diluted cell populations from large sample volumes using 3D carbon-electrode dielectrophoresis.

    Science.gov (United States)

    Islam, Monsur; Natu, Rucha; Larraga-Martinez, Maria Fernanda; Martinez-Duarte, Rodrigo

    2016-05-01

    Here, we report on an enrichment protocol using carbon electrode dielectrophoresis to isolate and purify a targeted cell population from sample volumes up to 4 ml. We aim at trapping, washing, and recovering an enriched cell fraction that will facilitate downstream analysis. We used an increasingly diluted sample of yeast, 10(6)-10(2) cells/ml, to demonstrate the isolation and enrichment of few cells at increasing flow rates. A maximum average enrichment of 154.2 ± 23.7 times was achieved when the sample flow rate was 10 μl/min and yeast cells were suspended in low electrically conductive media that maximizes dielectrophoresis trapping. A COMSOL Multiphysics model allowed for the comparison between experimental and simulation results. Discussion is conducted on the discrepancies between such results and how the model can be further improved.

  6. A large volume striped bass egg incubation chamber: design and comparison with a traditional method

    Science.gov (United States)

    Harper, C.J.

    2009-01-01

    I conducted a comparative study of a new jar design (experimental chamber) with a standard egg incubation vessel (McDonald jar). Experimental chambers measured 0.4 m in diameter by 1.3 m in height and had a volume of 200 L. McDonald hatching jars measured 16 cm in diameter by 45 cm in height and had a volume of 6 L. Post-hatch survival was estimated at 48, 96 and 144 h. Stocking rates resulted in an average egg density of 21.9 eggs ml-1 (range = 21.6 – 22.1) for McDonald jars and 10.9 eggs ml-1 (range = 7.0 – 16.8) for experimental chambers. I was unable to detect an effect of container type on survival to 48, 96 or 144 h. At 144 h striped bass fry survival averaged 37.3% for McDonald jars and 34.2% for experimental chambers. Survival among replicates was significantly different. Survival of striped bass significantly decreased between 96 and 144 h. Mean survival among replicates ranged from 12.4 to 57.3%. I was unable to detect an effect of initial stocking density on survival. Experimental jars allow for incubation of a larger number of eggs in a much smaller space. As hatchery production is often limited by space or water supply, experimental chambers offer an alternative to extending spawning activities, thereby reducing manpower and cost. However, the increase in the number of eggs per rearing container does increase the risk associated with catastrophic loss of a production unit. I conclude the experimental chamber is suitable for striped bass egg incubation.

  7. Large-volume heat storage tank made of GFK; Grosswaermespeichertank aus GFK

    Energy Technology Data Exchange (ETDEWEB)

    Buehl, J.; Schultheis, P. [Technische Univ. Ilmenau (Germany). Fachgebiet Technische Thermodynamik

    1998-12-31

    The Technical University of Ilmenau, the company Verbundwerkstoff- und Kunststoffanwendungstechnik Schoenbrunn, the Institute for Aerospace and Light-weight construction of Dresden University with its approved testing facilities for plastics and the Institute for Construction Engineering in Berlin and several other institutions co-operated since 1996 in developing a concept for a series of long-term heat storage tanks up to 6,000 cubic metres storage volume made of plastic (GFK components) with a combined thermal insulation. A model tank (sandwich body with proportional thermal insulation layer and selected mixed laminates) with a volume of 1.5 cubic metres was built and installed in November 1996. The tank has been continuously operated at various test levels. The experiment proves the longevity of the materials used. (orig.) [Deutsch] In Zusammenarbeit der TU Ilmenau mit der Fa. Verbundwerkstoff - und Kunststoffanwendungstechnik Schoenbrunn und dem Institut fuer Luftfahrttechnik und Leichtbau Dresden, seiner akkredierten Pruefstelle fuer Kunststoffe, in Abstimmung mit dem Institut fuer Bautechnik Berlin und weiteren Einrichtungen und Partnern wird seit 1996 an einem Konzept fuer eine Typenreihe Langzeitwaermespeicher bis vorerst 6.000 m{sup 3} Speichervolumen aus Kunststoff (GFK-Komponenten) und kombinierter integrierter thermischer Isolation gearbeitet. Im Vorfeld dieser Entwicklung wurde auf der Basis vorausgewaehlter Materialien und Kompositionen ein Musterspeicher (ein Sandwich - Modellkoerper mit proportionaler Waermedaemmschicht sowie ausgewaehlten Mischlaminaten) mit einem Speichervolumen von 1,5 m{sup 3} realisiert. Dieser Musterspeicher wurde im November 1996 installiert und wird seither kontinuierlich in den entsprechenden Erprobungsstufen betrieben. Der Nachweis der Langlebigkeit der eingesetzten Materialien wurde experimentell erbracht. (orig.)

  8. Glass-covering of large building volumes. An interdisciplinary evaluation of a shopping centre

    Energy Technology Data Exchange (ETDEWEB)

    Oeman, R. [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Building Technology

    1994-12-31

    Systematized experiences of the function of large glass-covered spaces related to shopping centres, hotels, office buildings etc. are still relatively limited. With the glazed pedestrian precincts of the rebuilt Skaerholmen Centre in Stockholm as the main object of interdisciplinary studies, the aim of this thesis is to provide additional knowledge of large glass-covered spaces (atrium buildings). The studies comprises thermal comfort, temperature conditions, ventilation, energy balance, humidity - mycology, acoustics, operation - maintenance - durability and sociology. To sum up, it is clear that in the Scandinavian climate there is every likelihood of large glass-covered spaces in the public places functioning well from a technical as well as a social point of view. The energy consumption on heating the whole complex, based on theoretical calculations and measurement, is shown to have been reduced by the order of 10%. figs., tabs., refs.

  9. RADON DIAGNOSTIC MEASUREMENT GUIDANCE FOR LARGE BUILDINGS - VOLUME 1. TECHNICAL REPORT

    Science.gov (United States)

    The report discusses the development of radon diagnostic procedures and mitigation strategies applicable to a variety of large non-residential buildings commonly found in Florida. The investigations document and evaluate the nature of radon occurrence and entry mechanisms for rad...

  10. RADON DIAGNOSTIC MEASUREMENT GUIDANCE FOR LARGE BUILDINGS - VOLUME 1. TECHNICAL REPORT

    Science.gov (United States)

    The report discusses the development of radon diagnostic procedures and mitigation strategies applicable to a variety of large non-residential buildings commonly found in Florida. The investigations document and evaluate the nature of radon occurrence and entry mechanisms for rad...

  11. Soft SUSY breaking parameters and RG running of squark and slepton masses in large volume Swiss Cheese compactifications

    Science.gov (United States)

    Misra, Aalok; Shukla, Pramod

    2010-03-01

    We consider type IIB large volume compactifications involving orientifolds of the Swiss Cheese Calabi-Yau WCP[1,1,1,6,9] with a single mobile space-time filling D3-brane and stacks of D7-branes wrapping the “big” divisor ΣB (as opposed to the “small” divisor usually done in the literature thus far) as well as supporting D7-brane fluxes. After reviewing our proposal of [1] (Misra and Shukla, 2010) for resolving a long-standing tension between large volume cosmology and phenomenology pertaining to obtaining a 10 GeV gravitino in the inflationary era and a TeV gravitino in the present era, and summarizing our results of [1] (Misra and Shukla, 2010) on soft supersymmetry breaking terms and open-string moduli masses, we discuss the one-loop RG running of the squark and slepton masses in mSUGRA-like models (using the running of the gaugino masses) to the EW scale in the large volume limit. Phenomenological constraints and some of the calculated soft SUSY parameters identify the D7-brane Wilson line moduli as the first two generations/families of squarks and sleptons and the D3-brane (restricted to the big divisor) position moduli as the two Higgses for MSSM-like models at TeV scale. We also discuss how the obtained open-string/matter moduli make it easier to impose FCNC constraints, as well as RG flow of off-diagonal squark mass(-squared) matrix elements.

  12. Extraterrestrial processing and manufacturing of large space systems. Volume 3: Executive summary

    Science.gov (United States)

    Miller, R. H.; Smith, D. B. S.

    1979-01-01

    Facilities and equipment are defined for refining processes to commercial grade of lunar material that is delivered to a 'space manufacturing facility' in beneficiated, primary processed quality. The manufacturing facilities and the equipment for producing elements of large space systems from these materials and providing programmatic assessments of the concepts are also defined. In-space production processes of solar cells (by vapor deposition) and arrays, structures and joints, conduits, waveguides, RF equipment radiators, wire cables, converters, and others are described.

  13. Extraterrestrial processing and manufacturing of large space systems, volume 1, chapters 1-6

    Science.gov (United States)

    Miller, R. H.; Smith, D. B. S.

    1979-01-01

    Space program scenarios for production of large space structures from lunar materials are defined. The concept of the space manufacturing facility (SMF) is presented. The manufacturing processes and equipment for the SMF are defined and the conceptual layouts are described for the production of solar cells and arrays, structures and joints, conduits, waveguides, RF equipment radiators, wire cables, and converters. A 'reference' SMF was designed and its operation requirements are described.

  14. No evidence of a threshold in traffic volume affecting road-kill mortality at a large spatio-temporal scale

    Energy Technology Data Exchange (ETDEWEB)

    Grilo, Clara, E-mail: clarabentesgrilo@gmail.com [Departamento de Biología de la Conservación, Estación Biológica de Doñana (EBD-CSIC), Calle Américo Vespucio s/n, E-41092 Sevilla (Spain); Centro Brasileiro de Estudos em Ecologia de Estradas, Departamento de Biologia, Universidade Federal de Lavras, Campus Universitário, 37200-000 Lavras, Minas Gerais (Brazil); Ferreira, Flavio Zanchetta; Revilla, Eloy [Departamento de Biología de la Conservación, Estación Biológica de Doñana (EBD-CSIC), Calle Américo Vespucio s/n, E-41092 Sevilla (Spain)

    2015-11-15

    Previous studies have found that the relationship between wildlife road mortality and traffic volume follows a threshold effect on low traffic volume roads. We aimed at evaluating the response of several species to increasing traffic intensity on highways over a large geographic area and temporal period. We used data of four terrestrial vertebrate species with different biological and ecological features known by their high road-kill rates: the barn owl (Tyto alba), hedgehog (Erinaceus europaeus), red fox (Vulpes vulpes) and European rabbit (Oryctolagus cuniculus). Additionally, we checked whether road-kill likelihood varies when traffic patterns depart from the average. We used annual average daily traffic (AADT) and road-kill records observed along 1000 km of highways in Portugal over seven consecutive years (2003–2009). We fitted candidate models using Generalized Linear Models with a binomial distribution through a sample unit of 1 km segments to describe the effect of traffic on the probability of finding at least one victim in each segment during the study. We also assigned for each road-kill record the traffic of that day and the AADT on that year to test for differences using Paired Student's t-test. Mortality risk declined significantly with traffic volume but varied among species: the probability of finding road-killed red foxes and rabbits occurs up to moderate traffic volumes (< 20,000 AADT) whereas barn owls and hedgehogs occurred up to higher traffic volumes (40,000 AADT). Perception of risk may explain differences in responses towards high traffic highway segments. Road-kill rates did not vary significantly when traffic intensity departed from the average. In summary, we did not find evidence of traffic thresholds for the analysed species and traffic intensities. We suggest mitigation measures to reduce mortality be applied in particular on low traffic roads (< 5000 AADT) while additional measures to reduce barrier effects should take into

  15. Magnetostructural martensitic transformations with large volume changes and magneto-strains in all-d-metal Heusler alloys

    Energy Technology Data Exchange (ETDEWEB)

    Wei, Z. Y.; Liu, E. K., E-mail: ekliu@iphy.ac.cn; Xi, X. K.; Zhang, H. W.; Wang, W. H.; Wu, G. H. [State Key Laboratory for Magnetism, Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China); Li, Y. [State Key Laboratory for Magnetism, Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China); School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130 (China); Han, X. L.; Du, Z. W. [National Center of Analysis and Testing for Nonferrous Metals and Electronic Materials, General Research Institute for Nonferrous Metals, Beijing 100088 (China); Luo, H. Z.; Liu, G. D. [School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130 (China)

    2016-08-15

    The all-d-metal Mn{sub 2}-based Heusler ferromagnetic shape memory alloys Mn{sub 50}Ni{sub 40−x}Co{sub x}Ti{sub 10} (x = 8 and 9.5) are realized. With a generic comparison between d-metal Ti and main-group elements in lowering the transformation temperature, the magnetostructural martensitic transformations are established by further introducing Co to produce local ferromagnetic Mn-Co-Mn configurations. A 5-fold modulation and (3, −2) stacking of [00 10] of martensite are determined by X-ray diffraction and HRTEM analysis. Based on the transformation, a large magneto-strain of 6900 ppm and a large volume change of −2.54% are observed in polycrystalline samples, which makes the all-d-metal magnetic martensitic alloys of interest for magnetic/pressure multi-field driven applications.

  16. SyPRID sampler: A large-volume, high-resolution, autonomous, deep-ocean precision plankton sampling system

    Science.gov (United States)

    Billings, Andrew; Kaiser, Carl; Young, Craig M.; Hiebert, Laurel S.; Cole, Eli; Wagner, Jamie K. S.; Van Dover, Cindy Lee

    2017-03-01

    The current standard for large-volume (thousands of cubic meters) zooplankton sampling in the deep sea is the MOCNESS, a system of multiple opening-closing nets, typically lowered to within 50 m of the seabed and towed obliquely to the surface to obtain low-spatial-resolution samples that integrate across 10 s of meters of water depth. The SyPRID (Sentry Precision Robotic Impeller Driven) sampler is an innovative, deep-rated (6000 m) plankton sampler that partners with the Sentry Autonomous Underwater Vehicle (AUV) to obtain paired, large-volume plankton samples at specified depths and survey lines to within 1.5 m of the seabed and with simultaneous collection of sensor data. SyPRID uses a perforated Ultra-High-Molecular-Weight (UHMW) plastic tube to support a fine mesh net within an outer carbon composite tube (tube-within-a-tube design), with an axial flow pump located aft of the capture filter. The pump facilitates flow through the system and reduces or possibly eliminates the bow wave at the mouth opening. The cod end, a hollow truncated cone, is also made of UHMW plastic and includes a collection volume designed to provide an area where zooplankton can collect, out of the high flow region. SyPRID attaches as a saddle-pack to the Sentry vehicle. Sentry itself is configured with a flight control system that enables autonomous survey paths to low altitudes. In its verification deployment at the Blake Ridge Seep (2160 m) on the US Atlantic Margin, SyPRID was operated for 6 h at an altitude of 5 m. It recovered plankton samples, including delicate living larvae, from the near-bottom stratum that is seldom sampled by a typical MOCNESS tow. The prototype SyPRID and its next generations will enable studies of plankton or other particulate distributions associated with localized physico-chemical strata in the water column or above patchy habitats on the seafloor.

  17. Large volume unresectable locally advanced non-small cell lung cancer: acute toxicity and initial outcome results with rapid arc

    Directory of Open Access Journals (Sweden)

    Fogliata Antonella

    2010-10-01

    Full Text Available Abstract Background To report acute toxicity, initial outcome results and planning therapeutic parameters in radiation treatment of advanced lung cancer (stage III with volumetric modulated arcs using RapidArc (RA. Methods Twenty-four consecutive patients were treated with RA. All showed locally advanced non-small cell lung cancer with stage IIIA-IIIB and with large volumes (GTV:299 ± 175 cm3, PTV:818 ± 206 cm3. Dose prescription was 66Gy in 33 fractions to mean PTV. Delivery was performed with two partial arcs with a 6 MV photon beam. Results From a dosimetric point of view, RA allowed us to respect most planning objectives on target volumes and organs at risk. In particular: for GTV D1% = 105.6 ± 1.7%, D99% = 96.7 ± 1.8%, D5%-D95% = 6.3 ± 1.4%; contra-lateral lung mean dose resulted in 13.7 ± 3.9Gy, for spinal cord D1% = 39.5 ± 4.0Gy, for heart V45Gy = 9.0 ± 7.0Gy, for esophagus D1% = 67.4 ± 2.2Gy. Delivery time was 133 ± 7s. At three months partial remission > 50% was observed in 56% of patients. Acute toxicities at 3 months showed 91% with grade 1 and 9% with grade 2 esophageal toxicity; 18% presented grade 1 and 9% with grade 2 pneumonia; no grade 3 acute toxicity was observed. The short follow-up does not allow assessment of local control and progression free survival. Conclusions RA proved to be a safe and advantageous treatment modality for NSCLC with large volumes. Long term observation of patients is needed to assess outcome and late toxicity.

  18. Paul Scherrer Institute Scientific and Technical Report 2000. Volume VI: Large Research Facilities

    Energy Technology Data Exchange (ETDEWEB)

    Foroughi, Fereydoun; Bercher, Renate; Buechli, Carmen; Zumkeller, Lotty [eds.

    2001-07-01

    The PSI Department Large Research Facilities (GFA) joins the efforts to provide an excellent research environment to Swiss and foreign research groups on the experimental facilities driven by our high intensity proton accelerator complex. Its divisions care for the running, maintenance and enhancement of the accelerator complex, the primary proton beamlines, the targets and the secondary beams as well as the neutron spallation source SINQ. The division for technical support and coordination provides for technical support to the research facility complementary to the basic logistic available from the department for logistics and marketing. Besides running the facilities, the staff of the department is also involved in theoretical and experimental research projects. Some of them address basic scientific questions mainly concerning the properties of micro- or nanostructured materials: experiments as well as large scale computer simulations of molecular dynamics were performed to investigate nonclassical materials properties. Others are related to improvements or extensions of the capabilities of our facilities. We also report on intriguing results from applications of the neutron capture radiography, the prompt gamma activation method and the isotope production facility at SINQ.

  19. Characteristics and Laser Performance of Yb3+-Doped Silica Large Mode Area Fibers Prepared by Sol–Gel Method

    Directory of Open Access Journals (Sweden)

    Shikai Wang

    2013-12-01

    Full Text Available Large-size 0.1 Yb2O3–1.0 Al2O3–98.9 SiO2 (mol% core glass was prepared by the sol–gel method. Its optical properties were evaluated. Both large mode area double cladding fiber (LMA DCF with core diameter of 48 µm and large mode area photonic crystal fiber (LMA PCF with core diameter of 90 µm were prepared from this core glass. Transmission loss at 1200 nm is 0.41 dB/m. Refractive index fluctuation is less than 2 × 10−4. Pumped by 976 nm laser diode LD pigtailed with silica fiber (NA 0.22, the slope efficiency of 54% and “light-to-light” conversion efficiency of 51% were realized in large mode area double cladding fiber, and 81 W laser power with a slope efficiency of 70.8% was achieved in the corresponding large mode area photonic crystal fiber.

  20. Paul Scherrer Institute Scientific and Technical Report 2001. Volume VI: Large Research Facilities

    Energy Technology Data Exchange (ETDEWEB)

    Bercher, R.; Buechli, C.; Zumkeller, L. (eds.)

    2002-03-01

    While the main effort in the past ten years was directed towards increasing the beam current from 100 to 2000 {mu}A and installation of additional user facilities like SINQ to satisfy new needs, we are now concentrating on stable operation at these high beam intensities. Unfortunately, 'stable operation' is not clearly defined. A few years ago, the accelerator physicists considered 80% beam on time excellent but the users complained about poor performance. Today we achieve a yearly mean beam on time of almost 90% at 1.7 mA and we have achieved 95% to 98% of the scheduled beam time for periods of weeks. These numbers seem to be satisfactory for the users. Despite this achievement, we try hard to further reduce the number of serious and long breakdowns, which are the main cause of the reduced yearly mean availability. Furthermore, breakdowns that necessitate long repair times are extremely detrimental for many experiments, which have only been allocated a few days of beam time. As a result of our discussions, we launched a number of activities, which include design and construction of improved power supplies, intensifying preventive maintenance, procuring vital spare parts, and reducing repair times through careful preparation. In addition, we were given permission to strengthen the accelerator staff with highly qualified physicists in order to study and solve several pending problems. We are aware that the planned measures will by no means be fast and will require considerable financial and personnel support. A long-standing issue concerning the improvement of the machine performance is the replacement of the aluminum cavities in the main ring accelerator by new high power copper cavities. The studies and tests on a model cavity are finished and we have ordered a prototype cavity, which will arrive in fall 2002 and be installed in the ring after a rigorous test phase in 2004. A list of scientific publications in 2000 is also provided.

  1. Solar neutrino detection in a large volume double-phase liquid argon experiment

    CERN Document Server

    Franco, D; Agnes, P; Agostino, L; Bottino, B; Davini, S; De Cecco, S; Fan, A; Fiorillo, G; Galbiati, C; Goretti, A M; Hungerford, E V; Ianni, Al; Ianni, An; Jollet, C; Marini, L; Martoff, C J; Meregaglia, A; Pagani, L; Pallavicini, M; Pantic, E; Pocar, A; Renshaw, A L; Rossi, B; Rossi, N; Suvorov, Y; Testera, G; Tonazzo, A; Wang, H; Zavatarelli, S

    2015-01-01

    The direct search for dark matter WIMP particles through their interaction with nuclei at the "neutrino floor" sensitivity, where neutrino-induced coherent scattering on nuclei starts contributing to the background, requires detectors capable of collecting exposures of the order of 1~ktonne yr free of background resulting from beta and gamma decays and cosmogenic and radiogenic neutrons. The same constraints are required for precision measurements of solar neutrinos elastically scattering on electrons. Two-phase liquid argon time projection chambers (LAr TPCs) are prime candidates for the ambitious program to explore the nature of dark matter. The large target, high scintillation light yield and good spatial resolution in all three cartesian directions concurrently allows a high precision measurement of solar neutrino fluxes. We studied the cosmogenic and radiogenic backgrounds affecting solar neutrino detection in a 300 tonne (100 tonne fiducial) LAr TPC operating at LNGS depth (3,800 meters of water equival...

  2. Effects of large gut volume in gelatinous zooplankton: ingestion rate, bolus production and food patch utilization by the jellyfish Sarsia tubulosa

    DEFF Research Database (Denmark)

    Hansson, L.J.; Kiørboe, Thomas

    2006-01-01

    Many gelatinous zooplankton consume a large amount of prey and have stomach volumes much greater than the volume of individual prey. We suggest that jellyfish can use their voluminous stomach as a buffering food-accumulating organ that allows the organism to feed at maximum clearance rate in a wide...

  3. Preparation of Bovine Serum Albumin (BSA) nanoparticles by desolvation using a membrane contactor: a new tool for large scale production.

    Science.gov (United States)

    Yedomon, B; Fessi, H; Charcosset, C

    2013-11-01

    Albumin nanoparticles are attractive drug delivery systems as they can be prepared under soft conditions and incorporate several kinds of molecules. The aim of this study was to upscale the desolvation process for preparing Bovine Serum Albumin (BSA) nanoparticles using a membrane contactor. At a first step, the BSA nanoparticles were prepared at small scale using a syringe pump. BSA nanoparticles of 139 nm in size, with a polydispersity index of 0.046, were obtained at the optimal conditions: pH 8.2, 100 mg mL(-1) BSA albumin solution (2 mL), and 1 mL min(-1) flow rate of ethanol addition (8 mL). The upscaling with a membrane contactor was achieved by permeating ethanol through the pores of a Shirasu Porous Glass (SPG Technology Co., Japan) membrane and circulating the aqueous phase tangentially to the membrane surface. By increasing the pressure of the ethanol from 1 to 2.7 bars, a progressive decrease in nanoparticle size was obtained with a high nanoparticles yield (around 94-96%). In addition, the flow rate of the circulating phase did not affect the BSA nanoparticle characteristics. At the optimal conditions (pH 8.2, 100 mg mL(-1) BSA albumin solution, pressure of ethanol 2.7 bars, flow rate of the circulating phase 30.7 mL s(-1)), the BSA nanoparticles showed similar characteristics to those obtained with the syringe pump. Large batches of BSA nanoparticles were prepared up to 10 g BSA. The BSA nanoparticles were stable at least during 2 months at 4 °C, and their characteristics were reproducible. It was then concluded that the membrane contactor technique could be a suitable method for the preparation of albumin nanoparticles at large scale with properties similar to that obtained at small scale.

  4. Planning, Designing, Building, and Moving a Large Volume Maternity Service to a New Labor and Birth Unit.

    Science.gov (United States)

    Thompson, Heather; Legorreta, Kimberly; Maher, Mary Ann; Lavin, Melanie M

    Our health system recognized the need to update facility space and associated technology for the labor and birth unit within our large volume perinatal service to improve the patient experience, and enhance safety, quality of care, and staff satisfaction. When an organization decides to invest $30 million dollars in a construction project such as a new labor and birth unit, many factors and considerations are involved. Financial support, planning, design, and construction phases of building a new unit are complex and therefore require strong interdisciplinary collaboration, leadership, and project management. The new labor and birth unit required nearly 3 years of planning, designing, and construction. Patient and family preferences were elicited through consumer focus groups. Multiple meetings with the administrative and nursing leadership teams, staff nurses, nurse midwives, and physicians were held to generate ideas for improvement in the new space. Involving frontline clinicians and childbearing women in the process was critical to success. The labor and birth unit moved to a new patient tower in a space that was doubled in square footage and geographically now on three separate floors. In the 6 months prior to the move, many efforts were made in our community to share our new space. The marketing strategy was very detailed and creative with ongoing input from the nursing leadership team. The nursing staff was involved in every step along the way. It was critical to have champions as workflow teams emerged. We hosted simulation drills and tested scenarios with new workflows. Move day was rehearsed with representatives of all members of the perinatal team participating. These efforts ultimately resulted in a move time of ~5 hours. Birth volumes increased 7% within the first 6 months. After 3 years in our new space, our birth volumes have risen nearly 15% and are still growing. Key processes and roles responsible for a successful build, efficient and safe move

  5. Solar neutrino detection in a large volume double-phase liquid argon experiment

    Science.gov (United States)

    Franco, D.; Giganti, C.; Agnes, P.; Agostino, L.; Bottino, B.; Canci, N.; Davini, S.; De Cecco, S.; Fan, A.; Fiorillo, G.; Galbiati, C.; Goretti, A. M.; Hungerford, E. V.; Ianni, Al.; Ianni, An.; Jollet, C.; Marini, L.; Martoff, C. J.; Meregaglia, A.; Pagani, L.; Pallavicini, M.; Pantic, E.; Pocar, A.; Razeti, M.; Renshaw, A. L.; Rossi, B.; Rossi, N.; Suvorov, Y.; Testera, G.; Tonazzo, A.; Wang, H.; Zavatarelli, S.

    2016-08-01

    Precision measurements of solar neutrinos emitted by specific nuclear reaction chains in the Sun are of great interest for developing an improved understanding of star formation and evolution. Given the expected neutrino fluxes and known detection reactions, such measurements require detectors capable of collecting neutrino-electron scattering data in exposures on the order of 1 ktonne-yr, with good energy resolution and extremely low background. Two-phase liquid argon time projection chambers (LAr TPCs) are under development for direct Dark Matter WIMP searches, which possess very large sensitive mass, high scintillation light yield, good energy resolution, and good spatial resolution in all three cartesian directions. While enabling Dark Matter searches with sensitivity extending to the ``neutrino floor'' (given by the rate of nuclear recoil events from solar neutrino coherent scattering), such detectors could also enable precision measurements of solar neutrino fluxes using the neutrino-electron elastic scattering events. Modeling results are presented for the cosmogenic and radiogenic backgrounds affecting solar neutrino detection in a 300 tonne (100 tonne fiducial) LAr TPC operating at LNGS depth (3,800 meters of water equivalent). The results show that such a detector could measure the CNO neutrino rate with ~15% precision, and significantly improve the precision of the 7Be and pep neutrino rates compared to the currently available results from the Borexino organic liquid scintillator detector.

  6. Fast large volume simulations of the 21-cm signal from the reionization and pre-reionization epochs

    Science.gov (United States)

    Santos, M. G.; Ferramacho, L.; Silva, M. B.; Amblard, A.; Cooray, A.

    2010-08-01

    While limited to low spatial resolution, the next-generation low-frequency radio interferometers that target 21-cm observations during the era of reionization and prior will have instantaneous fields of view that are many tens of deg2 on the sky. Predictions related to various statistical measurements of the 21-cm brightness temperature must then be pursued with numerical simulations of reionization with correspondingly large volume box sizes, of the order of 1000 Mpc on one side. We pursue a semi-numerical scheme to simulate the 21-cm signal during and prior to reionization by extending a hybrid approach where simulations are performed by first laying down the linear dark matter density field, accounting for the non-linear evolution of the density field based on second-order linear perturbation theory as specified by the Zel'dovich approximation, and then specifying the location and mass of collapsed dark matter haloes using the excursion-set formalism. The location of ionizing sources and the time evolving distribution of ionization field is also specified using an excursion-set algorithm. We account for the brightness temperature evolution through the coupling between spin and gas temperature due to collisions, radiative coupling in the presence of Lyman α photons and heating of the intergalactic medium, such as due to a background of X-ray photons. The hybrid simulation method we present is capable of producing the required large volume simulations with adequate resolution in a reasonable time, so a large number of realizations can be obtained with variations in assumptions related to astrophysics and background cosmology that govern the 21-cm signal.

  7. Preparation of liposomes: a novel application of microengineered membranes--from laboratory scale to large scale.

    Science.gov (United States)

    Laouini, A; Charcosset, C; Fessi, H; Holdich, R G; Vladisavljević, G T

    2013-12-01

    A novel ethanol injection method using microengineered nickel membrane was employed to produce POPC (1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine) and Lipoid(®) E80 liposomes at different production scales. A stirred cell device was used to produce 73ml of the liposomal suspension and the product volume was then increased by a factor of 8 at the same transmembrane flux (140lm(-2)h(-1)), volume ratio of the aqueous to organic phase (4.5) and peak shear stress on the membrane surface (2.7Pa). Two different strategies for shear control on the membrane surface have been used in the scaled-up versions of the process: a cross flow recirculation of the aqueous phase across the membrane surface and low frequency oscillation of the membrane surface (∼40Hz) in a direction normal to the flow of the injected organic phase. Using the same membrane with a pore size of 5μm and pore spacing of 200μm in all devices, the size of the POPC liposomes produced in all three membrane systems was highly consistent (80-86nm) and the coefficient of variation ranged between 26 and 36%. The smallest and most uniform liposomal nanoparticles were produced in a novel oscillating membrane system. The mean vesicle size increased with increasing the pore size of the membrane and the injection time. An increase in the vesicle size over time was caused by deposition of newly formed phospholipid fragments onto the surface of the vesicles already formed in the suspension and this increase was most pronounced for the cross flow system, due to long recirculation time. The final vesicle size in all membrane systems was suitable for their use as drug carriers in pharmaceutical formulations.

  8. Electrochemical preparation of metal microstructures on large areas of etched ion track membranes

    Science.gov (United States)

    Dobrev, D.; Vetter, J.; Angert, N.

    1999-01-01

    A microgalvanic method for metal filling of etched ion tracks in organic foils on large areas is described. The method and the used galvanic cell permit the deposition of stable standing individual metal whiskers with high aspect ratio and a density of 10 5-10 8 per cm 2 on an area of 12.5 cm 2. The method was verified with copper and it is suitable also for various other metals. It can be applied for the replication of etched ion tracks and for the fabrication of microstructures containing large numbers of individual metal whiskers.

  9. Preparation of Super-Thin, Large-Area, Double-Sided Gold-Plated Mylar Film

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    Large-area multi-wire parallel plane avalanche counter (MWPPAC) is a kind of gas detector widely used in nuclear experiments. MWPPAC is composed of front-window film, X wires, anode film, Y wires and rear-window film, which is mostly utilized to measuring

  10. Use of large-scale chromatography in the preparation of armodafinil.

    Science.gov (United States)

    Hauck, Willy; Adam, Philippe; Bobier, Christelle; Landmesser, Nelson

    2008-08-01

    Armodafinil, the (R)-enantiomer of modafinil, is a medication used to treat the excessive sleepiness associated with narcolepsy, obstructive sleep apnea/hypopnea syndrome, and shift work sleep disorder. We report here the chemical development of armodafinil and the investigations that led to a commercial route to prepare this pure enantiomer. Three synthetic approaches were used to provide the chiral sulfoxide. Resolution via preferential crystallization was used for phase I clinical trials and was subsequently replaced by chiral chromatography, enabling us to pursue a rapid filing and registration of the API. Finally, the commercial route was developed and employed asymmetric oxidation catalyzed by a titanium(IV) isopropoxide and diethyl tartrate system. The advantages of choosing a chromatographic development pathway to expedite registration while concurrently developing an economical chiral synthesis route is discussed in the context of armodafinil development.

  11. Comparison of pathogen DNA isolation methods from large volumes of whole blood to improve molecular diagnosis of bloodstream infections.

    Directory of Open Access Journals (Sweden)

    Anne J M Loonen

    Full Text Available For patients suffering from bloodstream infections (BSI molecular diagnostics from whole blood holds promise to provide fast and adequate treatment. However, this approach is hampered by the need of large blood volumes. Three methods for pathogen DNA isolation from whole blood were compared, i.e. an enzymatic method (MolYsis, 1-5 ml, the novel non-enzymatic procedure (Polaris, 1-5 ml, and a method that does not entail removal of human DNA (Triton-Tris-EDTA EasyMAG, 200 µl. These methods were evaluated by processing blood spiked with 0-1000 CFU/ml of Staphylococcus aureus, Pseudomonas aeruginosa and Candida albicans. Downstream detection was performed with real-time PCR assays. Polaris and MolYsis processing followed by real-time PCRs enabled pathogen detection at clinically relevant concentrations of 1-10 CFU/ml blood. By increasing sample volumes, concurrent lower cycle threshold (Ct values were obtained at clinically relevant pathogen concentrations, demonstrating the benefit of using larger blood volumes. A 100% detection rate at a concentration of 10 CFU/ml for all tested pathogens was obtained with the Polaris enrichment, whereas comparatively lower detection rates were measured for MolYsis (50-67% and EasyMAG (58-79%. For the samples with a concentration of 1 CFU/ml Polaris resulted in most optimal detection rates of 70-75% (MolYsis 17-50% and TTE-EasyMAG 20-36%. The Polaris method was more reproducible, less labour intensive, and faster (45 minutes (including Qiagen DNA extraction vs. 2 hours (MolYsis. In conclusion, Polaris and MolYsis enrichment followed by DNA isolation and real-time PCR enables reliable and sensitive detection of bacteria and fungi from 5 ml blood. With Polaris results are available within 3 hours, showing potential for improved BSI diagnostics.

  12. Preparation and characterization of monodisperse large-porous silica microspheres as the matrix for protein separation.

    Science.gov (United States)

    Xia, Hongjun; Wan, Guangping; Zhao, Junlong; Liu, Jiawei; Bai, Quan

    2016-11-04

    High performance liquid chromatography (HPLC) is a kind of efficient separation technology and has been used widely in many fields. Micro-sized porous silica microspheres as the most popular matrix have been used for fast separation and analysis in HPLC. In this paper, the monodisperse large-porous silica microspheres with controllable size and structure were successfully synthesized with polymer microspheres as the templates and characterized. First, the poly(glycidyl methacrylate-co-ethyleneglycol dimethacrylate) microspheres (PGMA-EDMA) were functionalized with tetraethylenepentamine (TEPA) to generate amino groups which act as a catalyst in hydrolysis of tetraethyl orthosilicate (TEOS) to form Si-containing low molecular weight species. Then the low molecular weight species diffused into the functionalized PGMA-EDMA microspheres by induction force of the amino groups to form polymer/silica hybrid microspheres. Finally, the organic polymer templates were removed by calcination, and the large-porous silica microspheres were obtained. The compositions, morphology, size distribution, specific surface area and pore size distribution of the porous silica microspheres were characterized by infrared analyzer, scanning-electron microscopy, dynamic laser scattering, the mercury intrusion method and thermal gravimetric analysis, respectively. The results show that the agglomeration of the hybrid microspheres can be overcome when the templates were functionalized with TEPA as amination reagent, and the yield of 95.7% of the monodisperse large-porous silica microspheres can be achieved with high concentration of polymer templates. The resulting large-porous silica microspheres were modified with octadecyltrichlorosilane (ODS) and the chromatographic evaluation was performed by separating the proteins and the digest of BSA. The baseline separation of seven kinds of protein standards was achieved, and the column delivered a better performance when separating BSA digests

  13. Brain perfusion CT for acute stroke using a 256-slice CT: improvement of diagnostic information by large volume coverage

    Energy Technology Data Exchange (ETDEWEB)

    Dorn, F. [Technical University, Department of Radiology, Klinikum rechts der Isar, Munich (Germany); Institut fuer Radiologie, Klinikum rechts der Isar der Technischen Universitaet Muenchen, Muenchen (Germany); Muenzel, D.; Meier, R.; Rummeny, E.J.; Huber, A. [Technical University, Department of Radiology, Klinikum rechts der Isar, Munich (Germany); Poppert, H. [Technical University, Department of Neurology, Klinikum rechts der Isar, Munich (Germany)

    2011-09-15

    To compare a 256-slice CT with a simulated standard CT for brain CT perfusion (CTP). CTP was obtained in 51 patients using a 256-slice CT (128 detector rows, flying z-focus, 8-cm detector width, 80 kV, 120mAs, 20 measurements, 1 CT image/2.5 s). Signal-to-noise ratios (SNR) were compared in grey and white matter. Perfusion maps were evaluated for cerebral blood flow (CBF), cerebral blood volume (CBV) and mean transit time (MTT) in hypoperfused areas and corresponding contralateral regions. Two reconstructed 10-mm slices for simulation of a standard CT (SDCT) were compared with the complete data sets (large-volume CT, LVCT). Adequate image quality was achieved in 50/51 cases. SNR were significantly different in grey and white matter. A perfusion deficit was present in 27 data sets. Differences between the hypoperfusions and the control regions were significant for MTT and CBF, but not for CBV. Three lesions were missed by SDCT but detected by LVCT; 24 lesions were covered incompletely by SDCT, and 6 by LVCT. 21 lesions were detected completely by LVCT, but none by SDCT. CTP imaging of the brain using an increased detector width can detect additional ischaemic lesions and cover most ischaemic lesions completely. (orig.)

  14. Development and sea trials of a subsea holographic camera for large volume in-situ recording of marine organisms

    Science.gov (United States)

    Watson, John; Alexander, Stephen J.; Craig, Gary; Hendry, David C.; Hobson, Peter R.; Lampitt, R. S.; Marteau, J.-M.; Nareid, Helge; Nebrensky, J. J.; Player, Michael A.; Saw, Kevin; Tipping, Keith

    2002-06-01

    We describe the development, construction and sea testing of An underwater holographic camera (HoloCam) for in situ recording of marine organisms and particles in large volumes of sea water. HoloCam comprises a laser, power supply, holographic recording optics, and plate holders, a water- tight housing and a support frame. Added to this are control electronics such that the entire camera is remotely operable and controllable from ship or dock-side. Uniquely the camera can simultaneously record both in-line and off-axis holograms using a pulsed frequency double Nd:YAG laser. In- line holography is capable of producing images of organisms with a resolution of better than 10 micrometers . Off-axis holograms of aquatic systems of up to 50,000 cm3 volume, have been recorded. Following initial laboratory testing, the holo-camera was evaluated in an observation tank and ultimately was tested in Loch Etive, Scotland. In-line and off-axis holograms were recorded to a depth of 100 m. We will present result on the ste dives and evaluation of the camera performance.

  15. Pretherapy metabolic tumour volume is an independent predictor of outcome in patients with diffuse large B-cell lymphoma

    Energy Technology Data Exchange (ETDEWEB)

    Sasanelli, Myriam; Meignan, Michel; Haioun, Corinne; Itti, Emmanuel [Paris-Est University, Nuclear Medicine and Lymphoid Malignancies Unit, Henri Mondor Hospital, Creteil (France); Berriolo-Riedinger, Alina; Casasnovas, Rene-Olivier [Nuclear Medicine and Hematology, Georges-Francois Leclerc Center, Le Bocage Hospital, Dijon (France); Biggi, Alberto; Gallamini, Andrea [Nuclear Medicine and Hematology, Santa Croce e Carle Hospital, Cuneo (Italy); Siegel, Barry A.; Cashen, Amanda F. [Washington University School of Medicine, Nuclear Medicine and Oncology, Siteman Cancer Center, St. Louis, MO (United States); Vera, Pierre; Tilly, Herve [Nuclear Medicine and Hematology, Henri Becquerel Center, Rouen (France); Versari, Annibale [Nuclear Medicine, Santa Maria Nuova Hospital-IRCCS, Reggio Emilia (Italy)

    2014-11-15

    We investigated the prognostic value of total metabolic tumour volume (TMTV) in diffuse large B-cell lymphoma (DLBCL). TMTV was measured in 114 patients with newly diagnosed DLBCL who underwent {sup 18}F-FDG PET/CT at baseline before immunochemotherapy. TMTV was computed by summing the volumes of all lymphomatous lesions after applying the local SUVmax threshold of 41 % using semiautomatic software. Prognostic value was assessed by Kaplan-Meier estimates of progression-free survival (PFS) and overall survival (OS). Median follow-up was 39 months. Average pretherapy TMTV was 509 ± 568 cm{sup 3}. The 3-year estimates of PFS were 77 % in the low metabolic burden group (TMTV ≤550 cm{sup 3}) and 60 % in the high metabolic burden group (TMTV >550 cm{sup 3}, p = 0.04), and prediction of OS was even better (87 % vs. 60 %, p = 0.0003). Cox regression showed independence of TMTV for OS prediction (p = 0.002) compared with other pretherapy indices of tumour burden, such as tumour bulk and the International Prognostic Index. Pretherapy TMTV is an independent predictor of outcome in patients with DLBCL. (orig.)

  16. Large-volume excitation of air, argon, nitrogen and combustible mixtures by thermal jets produced by nanosecond spark discharges

    Science.gov (United States)

    Stepanyan, Sergey; Hayashi, Jun; Salmon, Arthur; Stancu, Gabi D.; Laux, Christophe O.

    2017-04-01

    This work presents experimental observations of strong expanding thermal jets following the application of nanosecond spark discharges. These jets propagate in a toroidal shape perpendicular to the interelectrode axis, with high velocities of up to 30 m s‑1 and over distances of the order of a cm. Their propagation length is much larger than the thermal expansion region produced by the conventional millisecond sparks used in car engine ignition, thus greatly improving the volumetric excitation of gas mixtures. The shape and velocity of the jets is found to be fairly insensitive to the shape of the electrodes. In addition, their spatial extent is found to increase with the number of nanosecond sparks and with the discharge voltage, and to decrease slightly with the pressure between 1 and 7 atm at constant applied voltage. Finally, this thermal jet phenomenon is observed in experiments conducted with many types of gas mixtures, including air, nitrogen, argon, and combustible CH4/air mixtures. This makes nanosecond repetitively pulsed discharges particularly attractive for aerodynamic flow control or plasma-assisted combustion because of their ability to excite large volumes of gas, typically about 100 times the volume of the discharge.

  17. The properties of a large volume-limited sample of face-on low surface brightness disk galaxies

    Institute of Scientific and Technical Information of China (English)

    Guo-Hu Zhong; Yan-Chun Liang; Feng-Shan Liu; Francois Hammer; Karen Disseau; Li-Cai Deng

    2012-01-01

    We select a large volume-limited sample of low surface brightness galaxies (LSBGs,2021) to investigate in detail their statistical properties and their differences from high surface brightness galaxies (HSBGs,3639).The distributions of stellar masses of LSBGs and HSBGs are nearly the same and they have the same median values.Thus this volume-limited sample has good completeness and is further removed from the effect of stellar masses on their other properties when we compare LSBGs to HSBGs.We found that LSBGs tend to have lower stellar metallicities and lower effective dust attenuations,indicating that they have lower dust than HSBGs.The LSBGs have relatively higher stellar mass-to-light ratios,higher gas fractions,lower star forming rates (SFRs),and lower specific SFRs than HSBGs.Moreover,with the decreasing surface brightness,gas fraction increases,but the SFRs and specific SFRs decrease rapidly for the sample galaxies.This could mean that the star formation histories between LSBGs and HSBGs are different,and HSBGs may have stronger star forming activities than LSBGs.

  18. Large volume injection in gas chromatography using the through oven transfer adsorption desorption interface operating under vacuum.

    Science.gov (United States)

    Aragón, Álvaro; Toledano, Rosa M; Gea, Sara; Cortés, José M; Vázquez, Ana M; Villén, Jesús

    2014-06-01

    The present work describes a modification of the Through Oven Transfer Adsorption Desorption (TOTAD) interface, consisting of coupling a vacuum system to reduce the consumption of the helium needed to totally remove the eluent for large volume injection (LVI) in gas chromatography (GC). Two different retention materials in the liner of the TOTAD interface were evaluated: Tenax TA, which was seen to be unsuitable for working under vacuum conditions, and polydimethylsiloxane (PDMS), which provided satisfactory repeatability as well as a good sensitivity. No variability was observed in the retention times in either case. Solutions containing organophosphorous pesticides in two different solvents, a polar (methanol/water) and a non-polar (hexane) solvent, were used to evaluate the modification. The vacuum system coupled to the TOTAD interface allowed up to 90% helium to be saved without affecting the performance.

  19. A 5 kA pulsed power supply for inductive and plasma loads in large volume plasma device

    Energy Technology Data Exchange (ETDEWEB)

    Srivastava, P. K., E-mail: pkumar@ipr.res.in; Singh, S. K.; Sanyasi, A. K.; Awasthi, L. M., E-mail: kushagra.lalit@gmail.com; Mattoo, S. K. [Institute for Plasma Research, Gandhinagar (India)

    2016-07-15

    This paper describes 5 kA, 12 ms pulsed power supply for inductive load of Electron Energy Filter (EEF) in large volume plasma device. The power supply is based upon the principle of rapid sourcing of energy from the capacitor bank (2.8 F/200 V) by using a static switch, comprising of ten Insulated Gate Bipolar Transistors (IGBTs). A suitable mechanism is developed to ensure equal sharing of current and uniform power distribution during the operation of these IGBTs. Safe commutation of power to the EEF is ensured by the proper optimization of its components and by the introduction of over voltage protection (>6 kV) using an indigenously designed snubber circuit. Various time sequences relevant to different actions of power supply, viz., pulse width control and repetition rate, are realized through optically isolated computer controlled interface.

  20. A 5 kA pulsed power supply for inductive and plasma loads in large volume plasma device

    Science.gov (United States)

    Srivastava, P. K.; Singh, S. K.; Sanyasi, A. K.; Awasthi, L. M.; Mattoo, S. K.

    2016-07-01

    This paper describes 5 kA, 12 ms pulsed power supply for inductive load of Electron Energy Filter (EEF) in large volume plasma device. The power supply is based upon the principle of rapid sourcing of energy from the capacitor bank (2.8 F/200 V) by using a static switch, comprising of ten Insulated Gate Bipolar Transistors (IGBTs). A suitable mechanism is developed to ensure equal sharing of current and uniform power distribution during the operation of these IGBTs. Safe commutation of power to the EEF is ensured by the proper optimization of its components and by the introduction of over voltage protection (>6 kV) using an indigenously designed snubber circuit. Various time sequences relevant to different actions of power supply, viz., pulse width control and repetition rate, are realized through optically isolated computer controlled interface.

  1. Recovery of Cryptosporidium oocysts from small and large volume water samples using a compressed foam filter system.

    Science.gov (United States)

    Sartory, D P; Parton, A; Parton, A C; Roberts, J; Bergmann, K

    1998-12-01

    A novel filter system comprising open cell reticulated foam rings compressed between retaining plates and fitted into a filtration housing was evaluated for the recovery of oocysts of Cryptosporidium from water. Mean recoveries of 90.2% from seeded small and large volume (100-2000 l) tap water samples, and 88.8% from 10-20 l river water samples, were achieved. Following a simple potassium citrate flotation concentrate clean-up procedure, mean recoveries were 56.7% for the tap water samples and 60.9% for river water samples. This represents a marked improvement in capture and recovery of Cryptosporidium oocysts from water compared with conventional polypropylene wound cartridge filters and membrane filters.

  2. Characterization of large volume 3.5″×8″ LaBr3:Ce detectors

    Science.gov (United States)

    Giaz, A.; Pellegri, L.; Riboldi, S.; Camera, F.; Blasi, N.; Boiano, C.; Bracco, A.; Brambilla, S.; Ceruti, S.; Coelli, S.; Crespi, F. C. L.; Csatlòs, M.; Frega, S.; Gulyàs, J.; Krasznahorkay, A.; Lodetti, S.; Million, B.; Owens, A.; Quarati, F.; Stuhl, L.; Wieland, O.

    2013-11-01

    The properties of large volume cylindrical 3.5″×8″ (89 mm×203 mm) LaBr3:Ce scintillation detectors coupled to the Hamamatsu R10233-100SEL photo-multiplier tube were investigated. These crystals are among the largest ones ever produced and still need to be fully characterized to determine how these detectors can be utilized and in which applications. We tested the detectors using monochromatic γ-ray sources and in-beam reactions producing γ rays up to 22.6 MeV; we acquired PMT signal pulses and calculated detector energy resolution and response linearity as a function of γ-ray energy. Two different voltage dividers were coupled to the Hamamatsu R10233-100SEL PMT: the Hamamatsu E1198-26, based on straightforward resistive network design, and the “LABRVD”, specifically designed for our large volume LaBr3:Ce scintillation detectors, which also includes active semiconductor devices. Because of the extremely high light yield of LaBr3:Ce crystals we observed that, depending on the choice of PMT, voltage divider and applied voltage, some significant deviation from the ideally proportional response of the detector and some pulse shape deformation appear. In addition, crystal non-homogeneities and PMT gain drifts affect the (measured) energy resolution especially in case of high-energy γ rays. We also measured the time resolution of detectors with different sizes (from 1″×1″ up to 3.5″×8″), correlating the results with both the intrinsic properties of PMTs and GEANT simulations of the scintillation light collection process. The detector absolute full energy efficiency was measured and simulated up to γ-rays of 30 MeV

  3. Characterization of large volume 3.5″×8″ LaBr{sub 3}:Ce detectors

    Energy Technology Data Exchange (ETDEWEB)

    Giaz, A.; Pellegri, L.; Riboldi, S. [Università degli Studi di Milano, Physics Department, Via Celoria 16, 20133 Milano (Italy); INFN Milano, Via Celoria 16, 20133 Milano (Italy); Camera, F., E-mail: Franco.Camera@mi.infn.it [Università degli Studi di Milano, Physics Department, Via Celoria 16, 20133 Milano (Italy); INFN Milano, Via Celoria 16, 20133 Milano (Italy); Blasi, N.; Boiano, C. [INFN Milano, Via Celoria 16, 20133 Milano (Italy); Bracco, A. [Università degli Studi di Milano, Physics Department, Via Celoria 16, 20133 Milano (Italy); INFN Milano, Via Celoria 16, 20133 Milano (Italy); Brambilla, S. [INFN Milano, Via Celoria 16, 20133 Milano (Italy); Ceruti, S. [Università degli Studi di Milano, Physics Department, Via Celoria 16, 20133 Milano (Italy); Coelli, S. [INFN Milano, Via Celoria 16, 20133 Milano (Italy); Crespi, F.C.L. [Università degli Studi di Milano, Physics Department, Via Celoria 16, 20133 Milano (Italy); INFN Milano, Via Celoria 16, 20133 Milano (Italy); Csatlòs, M. [Institute of Nuclear Research of the Hungarian Academy of Sciences (ATOMKI), P.O. Box 51, H-4001 Debrecen (Hungary); Frega, S. [Università degli Studi di Milano, Physics Department, Via Celoria 16, 20133 Milano (Italy); Gulyàs, J.; Krasznahorkay, A. [Institute of Nuclear Research of the Hungarian Academy of Sciences (ATOMKI), P.O. Box 51, H-4001 Debrecen (Hungary); Lodetti, S. [Università degli Studi di Milano, Physics Department, Via Celoria 16, 20133 Milano (Italy); Million, B. [INFN Milano, Via Celoria 16, 20133 Milano (Italy); Owens, A.; Quarati, F. [SRE-PA, ESA/ESTEC, Keplerlaan 1, 2200AG Noordwijk (Netherlands); Stuhl, L. [Institute of Nuclear Research of the Hungarian Academy of Sciences (ATOMKI), P.O. Box 51, H-4001 Debrecen (Hungary); and others

    2013-11-21

    The properties of large volume cylindrical 3.5″×8″ (89 mm×203 mm) LaBr{sub 3}:Ce scintillation detectors coupled to the Hamamatsu R10233-100SEL photo-multiplier tube were investigated. These crystals are among the largest ones ever produced and still need to be fully characterized to determine how these detectors can be utilized and in which applications. We tested the detectors using monochromatic γ–ray sources and in-beam reactions producing γ rays up to 22.6 MeV; we acquired PMT signal pulses and calculated detector energy resolution and response linearity as a function of γ-ray energy. Two different voltage dividers were coupled to the Hamamatsu R10233-100SEL PMT: the Hamamatsu E1198-26, based on straightforward resistive network design, and the “LABRVD”, specifically designed for our large volume LaBr{sub 3}:Ce scintillation detectors, which also includes active semiconductor devices. Because of the extremely high light yield of LaBr{sub 3}:Ce crystals we observed that, depending on the choice of PMT, voltage divider and applied voltage, some significant deviation from the ideally proportional response of the detector and some pulse shape deformation appear. In addition, crystal non-homogeneities and PMT gain drifts affect the (measured) energy resolution especially in case of high-energy γ rays. We also measured the time resolution of detectors with different sizes (from 1″×1″ up to 3.5″×8″), correlating the results with both the intrinsic properties of PMTs and GEANT simulations of the scintillation light collection process. The detector absolute full energy efficiency was measured and simulated up to γ-rays of 30 MeV.

  4. Preparing laboratory and real-world EEG data for large-scale analysis: A containerized approach

    Directory of Open Access Journals (Sweden)

    Nima eBigdely-Shamlo

    2016-03-01

    Full Text Available Large-scale analysis of EEG and other physiological measures promises new insights into brain processes and more accurate and robust brain-computer interface (BCI models.. However, the absence of standard-ized vocabularies for annotating events in a machine understandable manner, the welter of collection-specific data organizations, the diffi-culty in moving data across processing platforms, and the unavailability of agreed-upon standards for preprocessing have prevented large-scale analyses of EEG. Here we describe a containerized approach and freely available tools we have developed to facilitate the process of an-notating, packaging, and preprocessing EEG data collections to enable data sharing, archiving, large-scale machine learning/data mining and (meta-analysis. The EEG Study Schema (ESS comprises three data Levels, each with its own XML-document schema and file/folder convention, plus a standardized (PREP pipeline to move raw (Data Level 1 data to a basic preprocessed state (Data Level 2 suitable for application of a large class of EEG analysis methods. Researchers can ship a study as a single unit and operate on its data using a standardized interface. ESS does not require a central database and provides all the metadata data necessary to execute a wide variety of EEG processing pipelines. The primary focus of ESS is automated in-depth analysis and meta-analysis EEG studies. However, ESS can also encapsulate meta-information for the other modalities such as eye tracking, that are in-creasingly used in both laboratory and real-world neuroimaging. ESS schema and tools are freely available at eegstudy.org, and a central cata-log of over 850 GB of existing data in ESS format is available at study-catalog.org. These tools and resources are part of a larger effort to ena-ble data sharing at sufficient scale for researchers to engage in truly large-scale EEG analysis and data mining (BigEEG.org.

  5. Effects of first-dose volume and exercise on the efficacy and tolerability of bowel preparations for colonoscopy in Chinese people

    Directory of Open Access Journals (Sweden)

    Qin Y

    2016-04-01

    Full Text Available Ying Qin, Wei Liu, Songbai Lin, Xiangfeng Li International Medical Services, Peking Union Medical College Hospital, Beijing, People’s Republic of China Aim: This study was designed to compare the efficacy and tolerability of bowel preparations with and without the higher first-dose volume of polyethylene glycol (PEG solution or exercise after drinking PEG solution in Chinese people. Methods: A total of 330 participants who had a colonoscopy done in Peking Union Medical College Hospital were randomly and evenly assigned to three groups. Participants in Group A ingested 1 L PEG solution and then ingested 2 L PEG solution at a rate of 250 mL every 15 minutes. Participants in Group B ingested 3 L PEG solution at a rate of 250 mL every 15 minutes and then exercised more than 10 minutes after ingesting each liter of PEG solution. Participants in Group C ingested 3 L PEG solution at a rate of 250 mL every 15 minutes. Experienced gastrointestinal endoscopists rated the efficacy of bowel preparations based on the Boston Bowel Preparation Scale score. A questionnaire regarding participants’ symptoms associated with bowel preparations was administered to evaluate participants’ tolerability. Results: The three groups had insignificant difference in the percentages of participants’ symptoms including dizziness, nausea, stomach ache, bloating, and asthenia. However, the percentages of participants having hunger sensation, sleep disturbance, and anal discomfort were significantly higher in groups with the higher first-dose volume of PEG solution or exercise after drinking PEG solution than without them. The three groups had insignificant difference in the Boston Bowel Preparation Scale score. Conclusion: Whether to add the higher first-dose volume of PEG solution and exercise after drinking PEG solution or not, all participants achieved a similar quality of bowel preparations. Bowel preparations without the additional first-dose volume of PEG

  6. Uniformity in large area ZnO:Al films prepared by reactive midfrequency magnetron sputtering

    CERN Document Server

    Hong, R J; Sittinger, V; Szyszka, B; Hoeing, T; Bräuer, G; Heide, G; Frischat, G H

    2002-01-01

    Al-doped zinc oxide (ZnO:Al) films were deposited on glass substrates using a reactive midfrequency magnetron sputtering process. The optical transmission and reflection as well as the electrical resistivity of the films prepared on an area of 1000x600 mm sup 2 were determined at different locations. Films with a uniform distribution of resistivity between 2.9x10 sup - sup 4 and 3.6x10 sup - sup 4 OMEGA cm and transmittance up to 88% in the visible spectral range were obtained. The ellipsometric spectra of the films were also analyzed using the Drude-Lorentz model. The calculated thicknesses of the films agreed well with those measured by a step profilometer. Secondary neutral mass spectrometry depth profiling showed uniform contents of Zn and O elements, while a slight periodic variation of the Al content was observed at different depths inside the film. A transition zone of 35-55 nm in width between the films and glass substrates due to the interdiffusion was also observed.

  7. Preparation of Large Area Double Sided YBCO Thin Films by DC Magneton Sputtering

    Institute of Scientific and Technical Information of China (English)

    Li Tao; Gu Hongwei; Wang Peiwen; Wang Xiaoping; Xie Bowei

    2004-01-01

    Tc, Jc and Rs properties of large area double sided YBCO thin films deposited on LaAlO3 substrates by direct current sputtering were reported.Film thickness of the obtained thin films is over 300 nm, Tc > 90 K; Rs can be as low as less than 1.0 mΩ(77 K, 10 GHz).Homogenousity of the properties around the plane was studied.Under the measnous distributions.Influences of substrate temperature and Ar and O2 pressures on properties of the double-sided thin films were discussed.

  8. Conditional large Fock state preparation and field state reconstruction in cavity QED.

    Science.gov (United States)

    Santos, M F; Solano, E; de Matos Filho, R L

    2001-08-27

    We propose a scheme for producing large Fock states in cavity QED via the implementation of a highly selective atom-field interaction. It is based on Raman excitation of a three-level atom by a classical field and a quantized field mode. Selectivity appears when one tunes to resonance a specific transition inside a chosen atom-field subspace, while other transitions remain dispersive, as a consequence of the field dependent electronic energy shifts. We show that this scheme can be also employed for reconstructing, in a new and efficient way, the Wigner function of the cavity field state.

  9. Dynamics of volume of competition practice and facilities of training of jumpers in length and triple in the process of long-term preparation

    Directory of Open Access Journals (Sweden)

    Sovenko S.P.

    2012-12-01

    Full Text Available Analysed and systematized information in relation to the volume of competition practice and facilities of different primary orientation of jumpers in length and triple in the process of long-term preparation. The expert questioning is conducted 16 trainers. The documents of planning of training process are analysed, the analysis of diaries of sportsmen is carried out (n=22. The volume of competition practice of sportsmen and facilities of training of different primary orientation is certain. The results of analysis in relation to the construction of training process are reflected by the leading trainers of Ukraine on track-and-field. An approach classification of facilities of training taking into account the specific of training process of sportsmen is presented. It is set that the volume of facilities of general preparation is most on the initial stages of long-term perfection, then stabilized on the stages specialized base and preparations to higher achievements and a few diminishes on maximal implementation of individual possibilities and maintainance of higher sporting trade phases. It is related to diminishing of duration of the general preparatory stages of annual preparation.

  10. Preparation of ceria with large particle size and high appearance density

    Institute of Scientific and Technical Information of China (English)

    WANG Songling; LIU Junyun; JIA Jiangtao; LIAO Chunsheng; YAN Chunhua

    2008-01-01

    Cerium is one of the most abundant rare earth dements in both bastnasite and monazite. Ceria has been widely used in optical catalytic, electrolyte, and sensor materials, with unique performances. With the development of functional materials, great interest has been focused on the synthesis and characterization of specific fine/mesoporous ceria powder. In this study, the modified precipitation and recrystallization processes combined with a controlled calcination process for fabricating the ceria with large particle size and high appearance density was reported. During precipitation, a certain amount of mineral acid such as nitric acid served as an additive, to adjust the precipitation and crystallization processes of cerium oxalates. An appropriate acidic condition could lead the process into the Oswald ripening stage and made the particles become bigger. Thus, the appearance density of powder was increased. The optimized conditions, such as the temperature, feeding speed, type and concentration of mineral acids, and the concentration of cerium-contained stock solution, were investigated and evaluated.

  11. X-ray diffraction and electroresistance measurements under high pressure and temperature using a large-volume cell

    Energy Technology Data Exchange (ETDEWEB)

    Principi, E; Minicucci, M [CNISM, CNR-INFM SOFT and Dipartimento di Fisica Universita degli Studi di Camerino via Madonna delle Carceri 62032, Camerino (Italy); Di Cicco, A

    2008-07-15

    In this communication we report about original experimental techniques for in-house x-ray diffraction and electrical resistance measurements under high-temperature and high pressure conditions, using large volume cells in the opposite anvil recessed geometry. The high-pressure devices we are currently using are a compact Paris-Edinburgh (PE) V5 150 Tons press and a 50 Tons standard hydraulic press, coupled usually with WC anvils and 10 mm or 7 mm boron-epoxy or pyrophyllite biconical gaskets for x-ray diffraction and resistance measurements respectively. Limiting pressures, using such a non-toroidal sample assembly and WC anvils, are about 10 GPa on samples of large sizes (10-20 mm{sup 3}). Samples can be heated using an hollow graphite cylinder as a crucible reaching temperatures as high as 2300 K, while the temperature can be measured up to 1300 K by using a K-type thermocouple. The highly automated setup developed for resistance measurements is described in details. In particular, we present electroresistance measurements of Bi melting under pressure and measurements of the Ge and LiF EOS (equation of state) at high temperature and pressure obtained using x-ray diffraction showing the sensitivity of the techniques. The relevance of these experiments to the exploitation of the potential of equipments available at synchrotron radiation facilities is emphasized.

  12. Long-term effects of large-volume liposuction on metabolic risk factors for coronary heart disease.

    Science.gov (United States)

    Mohammed, B Selma; Cohen, Samuel; Reeds, Dominic; Young, V Leroy; Klein, Samuel

    2008-12-01

    Abdominal obesity is associated with metabolic risk factors for coronary heart disease (CHD). Although we previously found that using liposuction surgery to remove abdominal subcutaneous adipose tissue (SAT) did not result in metabolic benefits, it is possible that postoperative inflammation masked the beneficial effects. Therefore, this study provides a long-term evaluation of a cohort of subjects from our original study. Body composition and metabolic risk factors for CHD, including oral glucose tolerance, insulin resistance, plasma lipid profile, and blood pressure were evaluated in seven obese (39 +/- 2 kg/m(2)) women before and at 10, 27, and 84-208 weeks after large-volume liposuction. Liposuction surgery removed 9.4 +/- 1.8 kg of body fat (16 +/- 2% of total fat mass; 6.1 +/- 1.4 kg decrease in body weight), primarily from abdominal SAT; body composition and weight remained the same from 10 through 84-208 weeks. Metabolic endpoints (oral glucose tolerance, homeostasis model assessment of insulin resistance, blood pressure and plasma triglyceride (TG), high-density lipoprotein (HDL)-cholesterol, and low-density lipoprotein (LDL)-cholesterol concentrations) obtained at 10 through 208 weeks were not different from baseline and did not change over time. These data demonstrate that removal of a large amount of abdominal SAT by using liposuction does not improve CHD metabolic risk factors associated with abdominal obesity, despite a long-term reduction in body fat.

  13. Transurethral dividing vaporesection for the treatment of large volume benign prostatic hyperplasia using 2 micron continuous wave laser

    Institute of Scientific and Technical Information of China (English)

    SUN Dong-chong; YANG Yong; WEI Zhi-tao; HONG Bao-fa; ZHANG Xu

    2010-01-01

    Background The safety and efficiency of transurethral laser resection of the prostate to treat benign prostatic hyperplasia have been verified. However, this method does still not manage large volume prostates efficiently. To tackle this problem, we have designed a method of "transurethral dividing vaporesection of prostate" using a 2 micron continuous wave laser. The aim of this study was to evaluate the safety and efficiency of this method in the management of large prostates (>80 ml).Methods In this study, 45 cases of benign prostatic hyperplasia with a median prostatic volume of (123.7±26.7) ml (range, 80.2-159.8 ml) were treated by the same surgeon under epidural anesthesia. During the surgery, superapubic catheters were needed, and saline solution was used for irrigation. First, the prostate was divided longitudinally into several parts from the bladder neck to the prostatic apex, and then gradually incised transversely chip by chip. Intraoperative blood transfusion rate, postoperative complications, maximum urinary flow rate, International Prostate Symptom Score and quality of life scores were recorded for statistical analysis using SPSS 16.0 software.Results Intraoperatively, no transurethral resection syndrome was observed, and no blood transfusions were needed.The resected prostatic chips were easily flushed out of the bladder through the resectoscope sheath without the use of a morcellator. Median vaporesection time was (95.0±13.2) minutes (range, 75-120 minutes), and the median retrieved and removed prostatic tissue were (25.2±5.1) g (range, 15.5-34.7 g) and (75.4±16.4) g (range, 43.8-106.1 g), respectively. Median catheter time and hospital stay were (3.3±0.9) days (range, 3-5 days) and (4.8±1.8) days (range, 3-9 days), respectively. After a follow-up of 6 to 12 months, two patients had stress urinary incontinence and three had anterior urethral strictures. Satisfactory improvement was seen in maximum urinary flow rate, International Prostate

  14. Large-scale preparation of active caspase-3 in E. coli by designing its thrombin-activatable precursors

    Directory of Open Access Journals (Sweden)

    Park Sung

    2008-12-01

    Full Text Available Abstract Background Caspase-3, a principal apoptotic effector that cleaves the majority of cellular substrates, is an important medicinal target for the treatment of cancers and neurodegenerative diseases. Large amounts of the protein are required for drug discovery research. However, previous efforts to express the full-length caspase-3 gene in E. coli have been unsuccessful. Results Overproducers of thrombin-activatable full-length caspase-3 precursors were prepared by engineering the auto-activation sites of caspase-3 precursor into a sequence susceptible to thrombin hydrolysis. The engineered precursors were highly expressed as soluble proteins in E. coli and easily purified by affinity chromatography, to levels of 10–15 mg from 1 L of E. coli culture, and readily activated by thrombin digestion. Kinetic evaluation disclosed that thrombin digestion enhanced catalytic activity (kcat/KM of the precursor proteins by two orders of magnitude. Conclusion A novel method for a large-scale preparation of active caspase-3 was developed by a strategic engineering to lack auto-activation during expression with amino acid sequences susceptible to thrombin, facilitating high-level expression in E. coli. The precursor protein was easily purified and activated through specific cleavage at the engineered sites by thrombin, generating active caspase-3 in high yields.

  15. Application of ultradisperse magnetic adsorbents for removal of small concentrations of pollutants from large volumes of water

    Science.gov (United States)

    Nechitailo, Galina S.; Kuznetsov, Anatoli; Kuznetsov, Oleg

    2016-07-01

    Pollution of natural bodies of water (rivers, lakes, ground water, etc) is unfortunately very common, both from natural sources like volcanic activity; and, even more importantly, from human activity, including disposal of industrial and municipal waste, mining, etc. Many toxic substances are harmful for humans and other organisms even in very low concentrations (e.g., less than 1 µg/L of cadmium is harmful, for Hg it is 0.5 µg/L, for phenol - 1 µg/L), and can remain in water for decades or longer. Cleaning large volumes of water even from low concentrations of pollutants is a challenging technological task and is very expensive. We propose to use suspension of ultradisperse magnetic adsorbents, for example, nanostructured ferro-carbon particles, produced by plasmachemical technique, for removing small concentrations of pollutants from large volumes of water. The suspension is introduced into the water. Due to their small sizes and densities similar to water (we measured the density of FC-4 ferro-carbon to be about 1 g/cm3; presumably due to porosity) the particles do not sediment for a long time (hours, days or longer), move due to Brownian motion and adsorb a variety of substances from the water. The particle surface can be modified to provide selectivity of the adsorption. Sorption capacities of ferro-carbon adsorbents is in dozens of percent. Therefore, to collect 1 kg of a pollutant, 2 to 20 kg of the adsorbents is required. Then the particles with the adsorbed contaminant can be collected (e.g., downstream of the river) using a variety of magnetic traps. The traps can consist of ferromagnetic wires and permanent magnets, a variety of simple and inexpensive designs are available. As a model system, the kinetics of adsorption of a highly diluted (0.002 mg/ml) aqueous solution of a low molecular weight compound (toluidine blue) by a small concentration of a ferro-carbon powder (FC-4) was studied by spectrophotometry. Before each measurement, the particles

  16. Comparação do volume da gota e custo do tratamento dos genéricos de maleato de timolol 0,5% Drop volume and cost of treatment with generic 0.5% timolol maleate preparations

    Directory of Open Access Journals (Sweden)

    João Antonio Prata Junior

    2004-06-01

    Full Text Available OBJETIVO: Comparar o volume da gota das medicações genéricas de maleato de timolol a fim de determinar o custo real do tratamento em relação à medicação de referência. MÉTODOS: Foi determinado o volume da gota do Timoptol® 0,5% (Merck Sharp & Dome e dos genéricos maleato de timolol 0,5% dos laboratórios Allergan-Lok, Cristália e Falcon. Cinco frascos de 5 ml de cada medicação foram adquiridos no mercado. Dez gotas de cada frasco foram pesadas em balança de precisão individualmente, bem como, um mililitro de cada frasco para a determinação do volume da gota. Com base no volume da gota foi calculada a duração média em dias e o custo anual, considerando-se o gasto diário de 4 gotas e o preço máximo ao consumidor publicado em maio de 2003 com alíquota de 18%. RESULTADOS: Observaram-se diferenças estatisticamente significantes do volume da gota entre as medicações (pPURPOSE: To compare drop volume and treatment cost of generic 0.5% timolol maleate preparations. METHODS: The drop volume of Timoptol® 0.5% (Merck Sharp & Dohme and its generic preparations (Allergan-Lok, Cristália and Falcon were determined. Five bottles of each medication were purchased at local drugstores. Using a precision scale, ten drops and one mililiter of each bottle were weighed. Drop volume was calculated by the relation between volume and weight. Duration, in days, of each bottle and annual cost were calculated considering a daily use of 4 drops and maximum price to consumers published May, 2003. RESULTS: Statistically significant differences were observed between drop volumes (p<0.0001%. Allergan-Lok timolol maleate had the largest drop (35.1 µl and the smallest was Falcon timolol maleate (27.3 µl. Timoptol® drop volume was 27.9 µl. Annual treatment costs were R$ 68.87 for Timoptol, R$ 72.76 for Allergan-Lok timolol maleate, R$ 50.00 for Cristalia timolol maleate and R$ 43.11 for Falcon timolol maleate (p<0.0001. Allergan-Lok timolol

  17. THE IMPORTANCE OF INFORMATION SYSTEMS IN THE MANAGEMENT AND PROCESSING OF LARGE DATA VOLUMES IN PUBLIC INSTITUTIONS

    Directory of Open Access Journals (Sweden)

    CARINA-ELENA STEGĂROIU

    2016-12-01

    Full Text Available Under a computerized society, technological resources become a source of identification for any community, institution or country. Globalization of information becomes a reality, all the resources having entered into a relationship of subordination with the World Wide Web, the information highways and the Internet. "Information technology - with its most important branch, data management computer science - enters a new era, in which the computer leads to the benefit of a navigable and transparent communication space, focusing on information". Therefore, in an information-based economy, information systems have been established which, based on management systems through the methods of algebra, with applications in economic engineering, have come to manage and process large volumes of data, especially in public institutions. Consequently, the Ministry of Public Affairs has implemented the “Increasing the public administration’s responsibility by modernising the information systems for generating the reports of the financial situations of public institutions” project (FOREXEBUG”, cod SMIS 34952, for which it received in 2012 non-refundable financing from the European Social Fund through the Operational Program for Developing the Administrative Capacity 2007-2013, based on which this paper will analyse the usefulness of implementing such a program in public institutions. Such a system aims to achieve a new form of reporting of budget execution and financial statements (including information related to legal commitments submitted monthly by each public institution in electronic, standardized, secure form, with increasing the reliability of data collected by cross-checking data from the treasury and providing reliable information for use by the Ministry of Finance, public institutions, other relevant institutions and the public, both at the level of detail and the consolidation possibilities at various levels, in parallel with their use for

  18. Simple and large scale refluxing method for preparation of Ce-doped ZnO nanostructures as highly efficient photocatalyst

    Energy Technology Data Exchange (ETDEWEB)

    Rezaei, M. [Department of Chemistry, Faculty of Science, University of Mohaghegh Ardabili, P.O. Box 179, Ardabil (Iran, Islamic Republic of); Habibi-Yangjeh, A., E-mail: ahabibi@uma.ac.ir [Department of Chemistry, Faculty of Science, University of Mohaghegh Ardabili, P.O. Box 179, Ardabil (Iran, Islamic Republic of)

    2013-01-15

    Graphical abstract: A simple method was applied for the preparation of Ce-doped ZnO nanostructures (mole fractions of Ce{sup 4+} ions are 0, 0.025, 0.05, 0.075 and 0.10) in water by refluxing for 3 h about at 90 Degree-Sign C. Highlights: Black-Right-Pointing-Pointer A simple refluxing method was applied for preparation of Ce-doped ZnO nanostructures. Black-Right-Pointing-Pointer The XRD patterns demonstrate that loading of Ce{sup 4+} ions does not change the structure of ZnO. Black-Right-Pointing-Pointer The results indicate that the nanostructures with 0.05 mole fraction of Ce{sup 4+} ions exhibit highest photocatalytic activity. Black-Right-Pointing-Pointer The nanostructures have highest photocatalytic activity at solutions with pH between 5.4 and 9. - Abstract: A simple method was applied for preparation of Ce-doped ZnO nanostructures (mole fractions of Ce{sup 4+} ions are 0, 0.025, 0.05, 0.075 and 0.10) in water by refluxing for 3 h about at 90 Degree-Sign C. This method is large scale, mild and involve no templates, surfactants or additives. The prepared nanostructures were investigated by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), and UV-vis diffuse reflectance spectroscopy (DRS) techniques. The XRD patterns demonstrate that the nanostructures have the same crystal structure, and loading of Ce{sup 4+} ions does not change the structure of ZnO. The SEM images show that with increasing mole fraction of Ce{sup 4+} ions, morphology of the nanostructures changes from nanoplates to nanospheres. Photocatalytic activity of the nanostructures toward photodegradation of methylene blue (MB) was evaluated under UV irradiation. The results indicate that the nanostructures with 0.05 mole fraction of Ce{sup 4+} ions exhibit highest photocatalytic activity among the prepared samples. The influence of various operational parameters such as refluxing time, catalyst weight, calcinations temperature and pH of solution on the photodegradation reaction

  19. New Trends in Mathematics Teaching, Volume IV.

    Science.gov (United States)

    Steiner, H. G., Ed.; Christiansen, Bent, Ed.

    This volume is largely based upon the preparation for and proceedings of the Third International Congress on Mathematical Education (ICME) held in Karlsruhe, Federal Republic of Germany, in August 1976. The volume deals with 13 broad themes of general educational interest for mathematics teachers and educators. Six of these themes divided the…

  20. Uncertainty quantification of seabed parameters for large data volumes along survey tracks with a tempered particle filter

    Science.gov (United States)

    Dettmer, J.; Quijano, J. E.; Dosso, S. E.; Holland, C. W.; Mandolesi, E.

    2016-12-01

    Geophysical seabed properties are important for the detection and classification of unexploded ordnance. However, current surveying methods such as vertical seismic profiling, coring, or inversion are of limited use when surveying large areas with high spatial sampling density. We consider surveys based on a source and receiver array towed by an autonomous vehicle which produce large volumes of seabed reflectivity data that contain unprecedented and detailed seabed information. The data are analyzed with a particle filter, which requires efficient reflection-coefficient computation, efficient inversion algorithms and efficient use of computer resources. The filter quantifies information content of multiple sequential data sets by considering results from previous data along the survey track to inform the importance sampling at the current point. Challenges arise from environmental changes along the track where the number of sediment layers and their properties change. This is addressed by a trans-dimensional model in the filter which allows layering complexity to change along a track. Efficiency is improved by likelihood tempering of various particle subsets and including exchange moves (parallel tempering). The filter is implemented on a hybrid computer that combines central processing units (CPUs) and graphics processing units (GPUs) to exploit three levels of parallelism: (1) fine-grained parallel computation of spherical reflection coefficients with a GPU implementation of Levin integration; (2) updating particles by concurrent CPU processes which exchange information using automatic load balancing (coarse grained parallelism); (3) overlapping CPU-GPU communication (a major bottleneck) with GPU computation by staggering CPU access to the multiple GPUs. The algorithm is applied to spherical reflection coefficients for data sets along a 14-km track on the Malta Plateau, Mediterranean Sea. We demonstrate substantial efficiency gains over previous methods. [This

  1. Novel experimental design for high pressure-high temperature electrical resistance measurements in a "Paris-Edinburgh" large volume press

    Science.gov (United States)

    Matityahu, Shlomi; Emuna, Moran; Yahel, Eyal; Makov, Guy; Greenberg, Yaron

    2015-04-01

    We present a novel experimental design for high sensitivity measurements of the electrical resistance of samples at high pressures (0-6 GPa) and high temperatures (300-1000 K) in a "Paris-Edinburgh" type large volume press. Uniquely, the electrical measurements are carried out directly on a small sample, thus greatly increasing the sensitivity of the measurement. The sensitivity to even minor changes in electrical resistance can be used to clearly identify phase transitions in material samples. Electrical resistance measurements are relatively simple and rapid to execute and the efficacy of the present experimental design is demonstrated by measuring the electrical resistance of Pb, Sn, and Bi across a wide domain of temperature-pressure phase space and employing it to identify the loci of phase transitions. Based on these results, the phase diagrams of these elements are reconstructed to high accuracy and found to be in excellent agreement with previous studies. In particular, by mapping the locations of several well-studied reference points in the phase diagram of Sn and Bi, it is demonstrated that a standard calibration exists for the temperature and pressure, thus eliminating the need for direct or indirect temperature and pressure measurements. The present technique will allow simple and accurate mapping of phase diagrams under extreme conditions and may be of particular importance in advancing studies of liquid state anomalies.

  2. Safety Analysis in Large Volume Vacuum Systems Like Tokamak: Experiments and Numerical Simulation to Analyze Vacuum Ruptures Consequences

    Directory of Open Access Journals (Sweden)

    A. Malizia

    2014-01-01

    Full Text Available The large volume vacuum systems are used in many industrial operations and research laboratories. Accidents in these systems should have a relevant economical and safety impact. A loss of vacuum accident (LOVA due to a failure of the main vacuum vessel can result in a fast pressurization of the vessel and consequent mobilization dispersion of hazardous internal material through the braches. It is clear that the influence of flow fields, consequence of accidents like LOVA, on dust resuspension is a key safety issue. In order to develop this analysis an experimental facility is been developed: STARDUST. This last facility has been used to improve the knowledge about LOVA to replicate a condition more similar to appropriate operative condition like to kamaks. By the experimental data the boundary conditions have been extrapolated to give the proper input for the 2D thermofluid-dynamics numerical simulations, developed by the commercial CFD numerical code. The benchmark of numerical simulation results with the experimental ones has been used to validate and tune the 2D thermofluid-dynamics numerical model that has been developed by the authors to replicate the LOVA conditions inside STARDUST. In present work, the facility, materials, numerical model, and relevant results will be presented.

  3. Anomalously large formula unit volume and its effect on the thermal behavior of LiBF4.

    Science.gov (United States)

    Matsumoto, Kazuhiko; Hagiwara, Rika; Mazej, Zoran; Goreshnik, Evgeny; Zemva, Boris

    2006-02-09

    The crystal structure of LiBF4 has been determined by single-crystal X-ray diffraction measurements. LiBF4 crystallizes as a merohedral twin in the trigonal space group P3(1)21 with a=4.892(5) A, c=11.002(12) A, V=228.0(4) A3, and Z=3 at 200 K. The twin is generated by a 2-fold rotation about the [10] direction. The lithium cation is coordinated by four fluorine atoms in a distorted tetrahedral manner, wherein two Li-F distances of 1.862(5) and 1.846(5) A are observed. The formula unit volume (FUV=V/Z) of 77.9 A3 for LiBF4 at 298 K is considerably larger than 72.7 A3 for NaBF4 and 72.5 A3 for AgBF4, despite the smaller size of Li+, indicating loose ionic packing of LiBF4. The thermodynamic evaluation of the decomposition temperature for LiBF4 was performed using the empirical relationship between the standard entropy and the FUV obtained. The results indicate that the large FUV of LiBF4 contributes to its higher decomposition temperature compared to that of LiPF6.

  4. Feasibility, efficacy, and safety of a simple insulin infusion protocol in a large volume cardiac surgery unit in India

    Directory of Open Access Journals (Sweden)

    Beena Bansal

    2015-01-01

    Full Text Available Aim: Inpatient hyperglycemia management is essential, but difficult to achieve especially in a large volume cardiac surgery setup, thus necessitating use of nurse-led insulin protocols. A rapid flux of nurses dealing with a huge workload has been a cause for traditionally not using nurse-led protocols in most Indian institutes. The challenges we faced were to have a simple protocol for the nurses to accept it without compromising on glycemic control. Therefore, this observational study was planned to measure the efficacy and safety of the insulin infusion protocol in cardiac surgery patients. Materials and Methods: Insulin protocol was implemented, using seven fixed columns of infusion with the nurse making decisions to initiate and titrate doses based on simple rules. Blood glucose (BG data captured from blood gas analyzers (glucometrics in the intervention group (i.e., after protocol implementation were compared to control group (i.e., before the protocol implementation. Results: The mean BG for the first 48 h was lower in the intervention group as compared to control group, without an increase in the episodes of hypoglycemia. The nurses found the protocol easy to understand, less time-consuming and there was no protocol deviation over 8 months after implementation. Conclusion: A small change in the process, allowing nurses to titrate insulin doses based on some rules and having seven fixed columns of insulin infusion rates, improved glycemic control and efficiency.

  5. Feasibility, efficacy, and safety of a simple insulin infusion protocol in a large volume cardiac surgery unit in India.

    Science.gov (United States)

    Bansal, Beena; Mithal, Ambrish; Carvalho, Pravin; Mehta, Yatin; Trehan, Naresh

    2015-01-01

    Inpatient hyperglycemia management is essential, but difficult to achieve especially in a large volume cardiac surgery setup, thus necessitating use of nurse-led insulin protocols. A rapid flux of nurses dealing with a huge workload has been a cause for traditionally not using nurse-led protocols in most Indian institutes. The challenges we faced were to have a simple protocol for the nurses to accept it without compromising on glycemic control. Therefore, this observational study was planned to measure the efficacy and safety of the insulin infusion protocol in cardiac surgery patients. Insulin protocol was implemented, using seven fixed columns of infusion with the nurse making decisions to initiate and titrate doses based on simple rules. Blood glucose (BG) data captured from blood gas analyzers (glucometrics) in the intervention group (i.e., after protocol implementation) were compared to control group (i.e., before the protocol implementation). The mean BG for the first 48 h was lower in the intervention group as compared to control group, without an increase in the episodes of hypoglycemia. The nurses found the protocol easy to understand, less time-consuming and there was no protocol deviation over 8 months after implementation. A small change in the process, allowing nurses to titrate insulin doses based on some rules and having seven fixed columns of insulin infusion rates, improved glycemic control and efficiency.

  6. Successful Large-volume Leukapheresis for Hematopoietic Stem Cell Collection in a Very-low-weight Brain Tumor Infant with Coagulopathy

    Directory of Open Access Journals (Sweden)

    Yu-Mei Liao

    2013-06-01

    Full Text Available Peripheral apheresis has become a safe procedure to collect hematopoietic stem cells, even in pediatric patients and donors. However, the apheresis procedure for small and sick children is more complicated due to difficult venous access, relatively large extracorporeal volume, toxicity of citrate, and unstable hemostasis. We report a small and sick child with refractory medulloblastoma, impaired liver function, and coagulopathy after several major cycles of cisplatin-based chemotherapy. She successfully received large-volume leukapheresis for hematopoietic stem cell collection, although the patient experienced severe coagulopathy during the procedures. Health care providers should be alert to this potential risk.

  7. Large wood recruitment processes and transported volumes in Swiss mountain streams during the extreme flood of August 2005

    Science.gov (United States)

    Steeb, Nicolas; Rickenmann, Dieter; Badoux, Alexandre; Rickli, Christian; Waldner, Peter

    2017-02-01

    The extreme flood event that occurred in August 2005 was the most costly (documented) natural hazard event in the history of Switzerland. The flood was accompanied by the mobilization of > 69,000 m3 of large wood (LW) throughout the affected area. As recognized afterward, wood played an important role in exacerbating the damages, mainly because of log jams at bridges and weirs. The present study aimed at assessing the risk posed by wood in various catchments by investigating the amount and spatial variability of recruited and transported LW. Data regarding LW quantities were obtained by field surveys, remote sensing techniques (LiDAR), and GIS analysis and was subsequently translated into a conceptual model of wood transport mass balance. Detailed wood budgets and transport diagrams were established for four study catchments of Swiss mountain streams, showing the spatial variability of LW recruitment and deposition. Despite some uncertainties with regard to parameter assumptions, the sum of reconstructed wood input and observed deposition volumes agree reasonably well. Mass wasting such as landslides and debris flows were the dominant recruitment processes in headwater streams. In contrast, LW recruitment from lateral bank erosion became significant in the lower part of mountain streams where the catchment reached a size of about 100 km2. According to our analysis, 88% of the reconstructed total wood input was fresh, i.e., coming from living trees that were recruited from adjacent areas during the event. This implies an average deadwood contribution of 12%, most of which was estimated to have been in-channel deadwood entrained during the flood event.

  8. Effect of high temperature curing on the compressive strength of concrete incorporating large volumes of fly ash

    Energy Technology Data Exchange (ETDEWEB)

    Rivera-Villarreal, R. [Universidad Autonoma de Nuevo Leon, Monterrey (Mexico)

    2001-07-01

    The effect of using different types of heat treatment on the compressive strength of concrete with and without large volumes of fly ash was studied. Curing of concrete is important to obtain a good quality concrete, but it is important to keep concrete from drying until the originally water-filled space in fresh cement paste has been filled to the desired extent by the products of hydration. In hot weather, high temperature promotes faster drying of concrete so a given degree of hydration is reached more rapidly than at lower temperatures. The provision of moist curing is advantageous because of a gradual gain in strength and because of reduced plastic shrinkage and drying shrinkage-cracking. The portland cement content in all the mixtures used in this study was 200 kg per cubic metre and the amount of fly ash varied from 0 to 33, 43, 50 and 56 per cent by mass of the total binder. A superplasticizer was used to obtain 200-220 mm slump. The compressive strength was tested at 3, 7, 14, 28, 56 days and at 6 months. Results showed that, using ASTM standard curing, the compressive strength of portland cement concrete made at 35 degrees C was reduced by about 12 per cent at 28 days compared to that of the concrete made at 23 degrees C. The AASHTO curing strength was found to be a bit higher than with the ASTM curing. The concrete made at 35 degrees C showed no loss of strength when continuous moist-curing was applied. The fly ash concrete mixtures that were cast at 35 degrees C were cured by covering them with membrane curing compounds and placed under ambient conditions. It was crucial to allow enough curing water to promote the pozzolanic reaction. The membrane curing did not allow the ingress of water to the concrete mass. 6 refs., 4 tabs., 13 figs.

  9. Risk scores to facilitate preoperative prediction of transfusion and large volume blood transfusion associated with adult cardiac surgery.

    Science.gov (United States)

    Goudie, R; Sterne, J A C; Verheyden, V; Bhabra, M; Ranucci, M; Murphy, G J

    2015-05-01

    The aim of this study was to develop two novel risk prediction scores for transfusion and bleeding that would be used to inform treatment decisions, quality assurance, and clinical trial design in cardiac surgery. Clinical data prospectively collected from 26 UK cardiac surgical centres and a single European centre were used to develop two risk prediction models: one for any red blood cell (RBC) transfusion, and the other for large volume blood transfusion (≥4 RBC units; LVBT), an index of severe blood loss. 'Complete case' data were available for 24 749 patients. Multiple imputation was used for missing covariate data (typically data set containing 39 970 patients. Risk models were developed in the complete case data set, with internal validation using leave-one-centre-out cross-validation. The final selected models were fitted to the imputed data set. Final risk scores were then compared with the performance of three existing scores: the Transfusion Risk and Clinical Knowledge score (TRACK), the Transfusion Risk Understanding Scoring Tool (TRUST), and the Papworth Bleeding Risk Score (BRiSc). The area under the receiver operating characteristic curve (AUC) was 0.77 (95% confidence interval 0.77-0.77) for the any RBC transfusion score and AUC 0.80 (0.79-0.80) for the LVBT score in the imputed data set. The LVBT model also showed excellent discrimination (Hosmer-Lemeshow P=0.32). In the imputed data set, the AUCs for the TRACK and TRUST scores for any RBC transfusion were 0.71 and 0.71, respectively, and for LVBT the AUC for the BRiSc score was 0.69. Two new risk scores for any RBC transfusion or LVBT among cardiac surgery patients have excellent discrimination, and could inform clinical decision making. © The Author 2015. Published by Oxford University Press on behalf of the British Journal of Anaesthesia. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  10. Rain Characteristics and Large-Scale Environments of Precipitation Objects with Extreme Rain Volumes from TRMM Observations

    Science.gov (United States)

    Zhou, Yaping; Lau, William K M.; Liu, Chuntao

    2013-01-01

    This study adopts a "precipitation object" approach by using 14 years of Tropical Rainfall Measuring Mission (TRMM) Precipitation Feature (PF) and National Centers for Environmental Prediction (NCEP) reanalysis data to study rainfall structure and environmental factors associated with extreme heavy rain events. Characteristics of instantaneous extreme volumetric PFs are examined and compared to those of intermediate and small systems. It is found that instantaneous PFs exhibit a much wider scale range compared to the daily gridded precipitation accumulation range. The top 1% of the rainiest PFs contribute over 55% of total rainfall and have 2 orders of rain volume magnitude greater than those of the median PFs. We find a threshold near the top 10% beyond which the PFs grow exponentially into larger, deeper, and colder rain systems. NCEP reanalyses show that midlevel relative humidity and total precipitable water increase steadily with increasingly larger PFs, along with a rapid increase of 500 hPa upward vertical velocity beyond the top 10%. This provides the necessary moisture convergence to amplify and sustain the extreme events. The rapid increase in vertical motion is associated with the release of convective available potential energy (CAPE) in mature systems, as is evident in the increase in CAPE of PFs up to 10% and the subsequent dropoff. The study illustrates distinct stages in the development of an extreme rainfall event including: (1) a systematic buildup in large-scale temperature and moisture, (2) a rapid change in rain structure, (3) explosive growth of the PF size, and (4) a release of CAPE before the demise of the event.

  11. Acoustic detection of cracks in the anvil of a large-volume cubic high-pressure apparatus

    Science.gov (United States)

    Yan, Zhaoli; Chen, Bin; Tian, Hao; Cheng, Xiaobin; Yang, Jun

    2015-12-01

    A large-volume cubic high-pressure apparatus with three pairs of tungsten carbide anvils is the most popular device for synthetic diamond production. Currently, the consumption of anvils is one of the important costs for the diamond production industry. If one of the anvils is fractured during the production process, the other five anvils in the apparatus may be endangered as a result of a sudden loss of pressure. It is of critical importance to detect and replace cracked anvils before they fracture for reduction of the cost of diamond production and safety. An acoustic detection method is studied in this paper. Two new features, nested power spectrum centroid and modified power spectrum variance, are proposed and combined with linear prediction coefficients to construct a feature vector. A support vector machine model is trained for classification. A sliding time window is proposed for decision-level information fusion. The experiments and analysis show that the recognition rate of anvil cracks is 95%, while the false-alarm rate is as low as 5.8 × 10-4 during a time window; this false-alarm rate indicates that at most one false alarm occurs every 2 months at a confidence level of 90%. An instrument to monitor anvil cracking was designed based on a digital signal processor and has been running for more than eight months in a diamond production field. In this time, two anvil-crack incidents occurred and were detected by the instrument correctly. In addition, no false alarms occurred.

  12. Acoustic detection of cracks in the anvil of a large-volume cubic high-pressure apparatus

    Energy Technology Data Exchange (ETDEWEB)

    Yan, Zhaoli, E-mail: zl-yan@mail.ioa.ac.cn; Tian, Hao; Cheng, Xiaobin; Yang, Jun [Key Laboratory of Noise and Vibration Research, Institute of Acoustics, Chinese Academy of Sciences, Beijing 100190 (China); Chen, Bin [School of Automation, Beijing University of Posts and Telecommunications, Beijing 100876 (China)

    2015-12-15

    A large-volume cubic high-pressure apparatus with three pairs of tungsten carbide anvils is the most popular device for synthetic diamond production. Currently, the consumption of anvils is one of the important costs for the diamond production industry. If one of the anvils is fractured during the production process, the other five anvils in the apparatus may be endangered as a result of a sudden loss of pressure. It is of critical importance to detect and replace cracked anvils before they fracture for reduction of the cost of diamond production and safety. An acoustic detection method is studied in this paper. Two new features, nested power spectrum centroid and modified power spectrum variance, are proposed and combined with linear prediction coefficients to construct a feature vector. A support vector machine model is trained for classification. A sliding time window is proposed for decision-level information fusion. The experiments and analysis show that the recognition rate of anvil cracks is 95%, while the false-alarm rate is as low as 5.8 × 10{sup −4} during a time window; this false-alarm rate indicates that at most one false alarm occurs every 2 months at a confidence level of 90%. An instrument to monitor anvil cracking was designed based on a digital signal processor and has been running for more than eight months in a diamond production field. In this time, two anvil-crack incidents occurred and were detected by the instrument correctly. In addition, no false alarms occurred.

  13. Advanced fractional crystallisation and homogenization of large-volume rhyolite before the Oraefajokull 1362 AD plinian eruption, SE Iceland

    Science.gov (United States)

    Selbekk, R. S.; Tronnes, R. G.

    2007-12-01

    In the 50 km wide Icelandic rift zones rhyolite magma is generated by partial melting of hydrated metabasaltic crust, subsiding under the weight of the growing volcanic pile. This mechanism of silicic melt formation is indicated by the basalt-rhyolite bimodality and rhyolite O-isotope composition. The low 18/16O-isotope ratios of rift zone rhyolites trace the high-latitude meteoric water component of the subsiding hydrated basalts [1]. The rhyolites of the volcanic flank zones (VFZ), however, have generally as heavy oxygen as the associated alkaline to transitional basalts and intermediate volcanics [2,3]. The minor volcanic loading of the older, thicker and stronger VFZ crust is insufficient for significant subsidence, and less pronounced basalt-rhyolite bimodality combined with other geochemical features support silicic melt generation by fractional crystallization. An extreme case in Icelandic, as well as global, perspective is the rhyolite magma of the plinian eruption from the large VFZ-volcano, Oraefajokull, in 1362 AD [4]. Glass, mineral and bulk tephra analyses show no chemical variation exceeding the analytical precision for the entire erupted volume of 2 km3 DRE. This applies even to the glass shards from distant locations in Greenland, Norway and Ireland. The total phenocryst content is 0.5-1 wt percent, with oligoclase (An14 Ab81 Or5.5), fayalite (Fa99.7 Fo0.3) and hedenbergite (Wo44.7 En2.6 Fs52.7) constituting 50- 80, 10-25 and 10-25 percent of the total phenocrysts, respectively. The extreme mineral compositions (especially pure fayalite and hedenbergite) resemble those of the granophyres in the Skaergaard and Bushveld complexes and differ from all other investigated rhyolites. The advanced fractionation and homogenisation to form the erupted 2 km3 DRE rhyolite is petrogenetically challenging, and a parental magma chamber of 20-40 km3 seems like a conservative estimate. The time-scale of the historic magma chamber evolution under Oraefajokull is

  14. Evaluation of real-time data obtained from gravimetric preparation of antineoplastic agents shows medication errors with possible critical therapeutic impact: Results of a large-scale, multicentre, multinational, retrospective study.

    Science.gov (United States)

    Terkola, R; Czejka, M; Bérubé, J

    2017-08-01

    Medication errors are a significant cause of morbidity and mortality especially with antineoplastic drugs, owing to their narrow therapeutic index. Gravimetric workflow software systems have the potential to reduce volumetric errors during intravenous antineoplastic drug preparation which may occur when verification is reliant on visual inspection. Our aim was to detect medication errors with possible critical therapeutic impact as determined by the rate of prevented medication errors in chemotherapy compounding after implementation of gravimetric measurement. A large-scale, retrospective analysis of data was carried out, related to medication errors identified during preparation of antineoplastic drugs in 10 pharmacy services ("centres") in five European countries following the introduction of an intravenous workflow software gravimetric system. Errors were defined as errors in dose volumes outside tolerance levels, identified during weighing stages of preparation of chemotherapy solutions which would not otherwise have been detected by conventional visual inspection. The gravimetric system detected that 7.89% of the 759 060 doses of antineoplastic drugs prepared at participating centres between July 2011 and October 2015 had error levels outside the accepted tolerance range set by individual centres, and prevented these doses from reaching patients. The proportion of antineoplastic preparations with deviations >10% ranged from 0.49% to 5.04% across sites, with a mean of 2.25%. The proportion of preparations with deviations >20% ranged from 0.21% to 1.27% across sites, with a mean of 0.71%. There was considerable variation in error levels for different antineoplastic agents. Introduction of a gravimetric preparation system for antineoplastic agents detected and prevented dosing errors which would not have been recognized with traditional methods and could have resulted in toxicity or suboptimal therapeutic outcomes for patients undergoing anticancer treatment.

  15. Volumetric-modulated arc therapy for the treatment of a large planning target volume in thoracic esophageal cancer.

    Science.gov (United States)

    Abbas, Ahmar S; Moseley, Douglas; Kassam, Zahra; Kim, Sun Mo; Cho, Charles

    2013-05-06

    Recently, volumetric-modulated arc therapy (VMAT) has demonstrated the ability to deliver radiation dose precisely and accurately with a shorter delivery time compared to conventional intensity-modulated fixed-field treatment (IMRT). We applied the hypothesis of VMAT technique for the treatment of thoracic esophageal carcinoma to determine superior or equivalent conformal dose coverage for a large thoracic esophageal planning target volume (PTV) with superior or equivalent sparing of organs-at-risk (OARs) doses, and reduce delivery time and monitor units (MUs), in comparison with conventional fixed-field IMRT plans. We also analyzed and compared some other important metrics of treatment planning and treatment delivery for both IMRT and VMAT techniques. These metrics include: 1) the integral dose and the volume receiving intermediate dose levels between IMRT and VMATI plans; 2) the use of 4D CT to determine the internal motion margin; and 3) evaluating the dosimetry of every plan through patient-specific QA. These factors may impact the overall treatment plan quality and outcomes from the individual planning technique used. In this study, we also examined the significance of using two arcs vs. a single-arc VMAT technique for PTV coverage, OARs doses, monitor units and delivery time. Thirteen patients, stage T2-T3 N0-N1 (TNM AJCC 7th edn.), PTV volume median 395 cc (range 281-601 cc), median age 69 years (range 53 to 85), were treated from July 2010 to June 2011 with a four-field (n = 4) or five-field (n = 9) step-and-shoot IMRT technique using a 6 MV beam to a prescribed dose of 50 Gy in 20 to 25 F. These patients were retrospectively replanned using single arc (VMATI, 91 control points) and two arcs (VMATII, 182 control points). All treatment plans of the 13 study cases were evaluated using various dose-volume metrics. These included PTV D99, PTV D95, PTV V9547.5Gy(95%), PTV mean dose, Dmax, PTV dose conformity (Van't Riet conformation number (CN)), mean lung dose

  16. The unsettled world of leak rate physics: 1 atm large-volume considerations do not apply to MEMS packages: a practitioner's perspective

    Science.gov (United States)

    Kullberg, Richard C.; Jonath, Arthur; Lowry, Robert K.

    2012-03-01

    The world of leak testing, and the applicable physics, is unsettled. While globally lower MIL-STD leak rate criteria are under consideration even for 1 atm-large volume packages, industry is conversely moving rapidly into very small volume MEMS and vacuum packaging for advanced devices. These changes point out serious conceptual disconnects between the reality of properly characterizing a leak and the conceptual tools used to ensure the desired lifetime. The physical understandings and associated tool sets used to test and model the leaks are described. We modeled two actual packages, a large, ~200 cc volume multichip module for aerospace applications and a small ~0.01cc volume MEMS package for sensor applications. Impacts of various physical models of leak flow into a package are compared to include Fickian Diffusion, The Davy Model, Howl-Mann, and an empirically derived model based on Kr-85 leak testing as called out in the most recent edition of MIL-STD-883. As shown in the comparisons, simple He leak testing and physical models based thereon fall apart in the small volume MEMS packaging space.

  17. Progressive preoperative pneumoperitoneum preparation (the Goni Moreno protocol) prior to large incisional hernia surgery: volumetric, respiratory and clinical impacts. A prospective study.

    Science.gov (United States)

    Sabbagh, C; Dumont, F; Fuks, D; Yzet, T; Verhaeghe, P; Regimbeau, J-M

    2012-02-01

    Progressive preoperative pneumoperitoneum (PPP) is used to prepare incisional hernias with loss of domain (IHLD) operations. The aim of the present study was to analyze the effect of PPP on peritoneal volume [measured using a new computed tomography (CT)-based method] and respiratory function. From July 2004 to July 2008, 19 patients were included in a prospective, observational study. The volumes of the incisional hernia (VIH), the abdominal cavity (VAC), the total peritoneal content (VP) and the VIH/VP ratio were measured before and after PPP using abdominal CT scan data. Spirometric parameters were measured before and after PPP, and postoperative clinical data were evaluated. Before and after PPP, the mean VIH was 1,420 cc and 2,110 cc (P  VIH before PPP. After PPP, the spirometric measurements revealed a restrictive syndrome. The overall postoperative morbidity rate was 37%. PPP increased the hernia and abdominal volumes. PPP induced a progressive, restrictive syndrome.

  18. The Feasibility of the Georgia Educational Model for Teacher Preparation--Elementary. Volume II A & B. Technical Report.

    Science.gov (United States)

    Johnson, Charles E., Ed.; And Others

    The two sections of volume 2 of the Georgia feasibility study on elementary teacher education are intended for readers who wish for a detailed analysis of the study's activities and findings. The first section contains detailed PERT charts for the 5-year development strategy, activity lists, and the time data and time reports. The second section…

  19. Volume rendering acceleration method based on optimal bricking for large volume data%基于最优化分块的大规模数据体绘制加速方法

    Institute of Scientific and Technical Information of China (English)

    彭伟; 李建新; 闫镔; 童莉; 陈健; 管士勇

    2011-01-01

    GPU-based volume rendering has become an active research area in the domain of volume visualization.Large volume data cannot be uploaded directly due to the limitation of GPU memory, which has been a bottleneck of the application of GPU.Bricking method could not only solve this problem, but also maintain the quality of original volume-rendered image.However, the data exchange via the graphics bus is really time consuming and will definitely degrade the render performance.As for these difficulties, the optimal bricking for large volume data was calculated by establishing the model for optimal bricking, and also a 3D texture named node code texture was constructed and distance template was improved to accelerate the octree-based bricking volume rendering.The experimental results illustrate that the proposed method can significantly accelerate the bricking-based volume rendering for large volume data.%GPU加速体绘制已成为体可视化领域的研究热点,然而超出显存的大规模数据无法直接载入,成为GPU应用的瓶颈.分块技术能够在保证图像质量的条件下解决该问题,但分块数据的频繁加载和访问明显降低了绘制速度.针对上述问题,通过建立最优化分块模型得到了大规模数据的最优分块,并通过构造节点编号纹理和改进距离模板设计的方法进一步提高了基于八叉树的分块体绘制算法的绘制速度.实验结果表明,该方法加速效果明显.

  20. All-solid-state reduced graphene oxide supercapacitor with large volumetric capacitance and ultralong stability prepared by electrophoretic deposition method.

    Science.gov (United States)

    Wang, Mei; Duong, Le Dai; Mai, Nguyen Thi; Kim, Sanghoon; Kim, Youngjun; Seo, Heewon; Kim, Ye Chan; Jang, Woojin; Lee, Youngkwan; Suhr, Jonghwan; Nam, Jae-Do

    2015-01-21

    Portable energy storage devices have gained special attention due to the growing demand for portable electronics. Herein, an all-solid-state supercapacitor is successfully fabricated based on a poly(vinyl alcohol)-H3PO4 (PVA-H3PO4) polymer electrolyte and a reduced graphene oxide (RGO) membrane electrode prepared by electrophoretic deposition (EPD). The RGO electrode fabricated by EPD contains an in-plane layer-by-layer alignment and a moderate porosity that accommodate the electrolyte ions. The all-solid-state RGO supercapacitor is thoroughly tested to give high specific volumetric capacitance (108 F cm(-3)) and excellent energy and power densities (7.5 Wh cm(-3) and 2.9 W cm(-3), respectively). In addition, the all-solid-state RGO supercapacitor exhibits an ultralong lifetime for as long as 180 days (335 000 cycles), which is an ultrahigh cycling capability for a solid-state supercapacitor. The RGO is also tested for being used as a transparent supercapacitor electrode demonstrating its possible use in various transparent optoelectronic devices. Due to the facile scale-up capability of the EPD process and RGO dispersion, the developed all-solid-state supercapacitor is highly applicable to large-area portable energy storage devices.

  1. Improved Cellulose Adsorption Method for the Preparation of Perovskite Oxides with Large Specific Surface Area at Low Temperature

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Perovskite-type La1-xSrxMO3-d (x=0,0.1,0.2, B=Co,Fe,Mn) oxides were prepared by pyrolysis of metal salt-(organic acid)-cellulose compound precursors. Low calcination temperatures, usually lower than 600oC, were needed. The specific surface area of the as-prepared oxides is higher than that prepared by the cellulose adsorption method, and is comparable to that prepared by sol-gel method. The effective organic acid could be EDTA acid, citric acid or DL-hydroxysuccinic acid, among them, EDTA acid is the best one.

  2. Results of volume-staged fractionated Gamma Knife radiosurgery for large complex arteriovenous malformations: obliteration rates and clinical outcomes of an evolving treatment paradigm.

    Science.gov (United States)

    Franzin, Alberto; Panni, Pietro; Spatola, Giorgio; Vecchio, Antonella Del; Gallotti, Alberto L; Gigliotti, Carmen R; Cavalli, Andrea; Donofrio, Carmine A; Mortini, Pietro

    2016-12-01

    OBJECTIVE There are few reported series regarding volume-staged Gamma Knife radiosurgery (GKRS) for the treatment of large, complex, cerebral arteriovenous malformations (AVMs). The object of this study was to report the results of using volume-staged Gamma Knife radiosurgery for patients affected by large and complex AVMs. METHODS Data from 20 patients with large AVMs were prospectively included in the authors' AVM database between 2004 and 2012. A staging strategy was used when treating lesion volumes larger than 10 cm(3). Hemorrhage and seizures were the presenting clinical feature for 6 (30%) and 8 (40%) patients, respectively. The median AVM volume was 15.9 cm(3) (range 10.1-34.3 cm(3)). The mean interval between stages (± standard deviation) was 15 months (± 9 months). The median margin dose for each stage was 20 Gy (range 18-25 Gy). RESULTS Obliteration was confirmed in 8 (42%) patients after a mean follow-up of 45 months (range 19-87 months). A significant reduction (> 75%) of the original nidal volume was achieved in 4 (20%) patients. Engel Class I-II seizure status was reported by 75% of patients presenting with seizures (50% Engel Class I and 25% Engel Class II) after radiosurgery. After radiosurgery, 71.5% (5/7) of patients who had presented with a worsening neurological deficit reported a complete resolution or amelioration. None of the patients who presented acutely because of hemorrhage experienced a new bleeding episode during follow-up. One (5%) patient developed radionecrosis that caused sensorimotor hemisyndrome. Two (10%) patients sustained a bleeding episode after GKRS, although only 1 (5%) was symptomatic. High nidal flow rate and a time interval between stages of less than 11.7 months were factors significantly associated with AVM obliteration (p = 0.021 and p = 0.041, respectively). Patient age younger than 44 years was significantly associated with a greater than 75% reduction in AVM volume but not with AVM obliteration (p = 0

  3. X-ray powder diffraction characterization of the large-volume unit cell of the M8 murataite polytype

    OpenAIRE

    MAKI, Ryosuke S. S.; Morgan, Peter E. D.; Suzuki, Yoshikazu

    2016-01-01

    We have used conventional X-ray powder diffraction to study one of the largest volume inorganic mixed oxide unit-supercell structures done so far. This necessitated some small-angle X-ray scattering-like observations at low angles from

  4. Enumeration of faecal indicator bacteria in large water volumes using on site membrane filtration to assess water treatment efficiency

    NARCIS (Netherlands)

    Hijnen, W.A.M.; Veendaal, D.; Speld, W.M.H. van der; Visser, Ate; Hoogenboezem, W.; Kooij, D. van der

    2000-01-01

    Sample volumes as tested in routine microbiological methods for determining the presence and absence of faecal indicator bacteria in water are too small to assess the actual concentration in the last stages of a water treatment. Consequently no accurate information can be obtained about the removal

  5. Enumeration of faecal indicator bacteria in large water volumes using on site membrane filtration to assess water treatment efficiency

    NARCIS (Netherlands)

    Hijnen, W.A.M.; Veendaal, D.; Speld, W.M.H. van der; Visser, Ate; Hoogenboezem, W.; Kooij, D. van der

    2000-01-01

    Sample volumes as tested in routine microbiological methods for determining the presence and absence of faecal indicator bacteria in water are too small to assess the actual concentration in the last stages of a water treatment. Consequently no accurate information can be obtained about the removal

  6. Trophic interactions among sympatric zooplanktivorous fish species in volume change conditions in a large, shallow, tropical lake

    Directory of Open Access Journals (Sweden)

    Rodrigo Moncayo-Estrada

    Full Text Available Significant reductions in the water volume of shallow lakes impose a restriction on species segregation promoting more interactions in the trophic relationships. The diets of three closely related zooplanktivorous silversides belonging to the Atherinopsidae species flock of lake Chapala , Mexico, were analyzed at two sites (Chirostoma jordani, C. labarcae, and C. consocium. Diets were described in critical shallow (August 2000 and volume recovery conditions (August 2005. Diets included mainly cladocerans (Bosmina, Ceriodaphnia, and Daphnia and copepods (Cyclops. A significant difference in diets was detected when comparing years (MRPP analysis, A = 0.22, p < 0.0001 and sites at different years (MRPP analysis, A = 0.17, p = 0.004. According to niche breadth mean values, species were classified as specialized and intermediate feeders. In shallow conditions, the small range of niche breadth (1.72 to 3.64 and high diet overlap values (D = 0.64, L = 8.62 indicated a high potential for interspecific exploitative interaction. When the lake volume recovered, an increase in the niche breadth range (1.04 to 4.96 and low niche overlap values (D = 0.53, L = 2.32 indicated a reduction of the species interaction. The Mann-Whitney U-test supported this pattern by showing a significant difference between years for niche overlap (p = 0.006. The increased interaction during the low volume suggests alternative segregation in life-history variations and other niche dimensions such as spatial or temporal distribution.

  7. High Voltage Test Apparatus for a Neutron EDM Experiment and Lower Limit on the Dielectric Strength of Liquid Helium at Large Volumes

    CERN Document Server

    Long, J C; Boissevain, J G; Clark, D J; Cooper, M D; Gómez, J J; Lamoreaux, S K; Mischke, R E; Penttila, S I

    2006-01-01

    A new search for a permanent electric dipole moment (EDM) of the neutron is underway using ultracold neutrons produced and held in a bath of superfluid helium. Attaining the target sensitivity requires maintaining an electric field of several tens of kilovolts per centimeter across the experimental cell, which is nominally 7.5 cm wide and will contain about 4 liters of superfluid. The electrical properties of liquid helium are expected to be sufficient to meet the design goals, but little is known about these properties for volumes and electrode spacings appropriate to the EDM experiment. Furthermore, direct application of the necessary voltages from an external source to the experimental test cell is impractical. An apparatus to amplify voltages in the liquid helium environment and to test the electrical properties of the liquid for large volumes and electrode spacings has been constructed. The device consists of a large-area parallel plate capacitor immersed in a 200 liter liquid helium dewar. Preliminary r...

  8. Effect of high-pressure homogenization preparation on mean globule size and large-diameter tail of oil-in-water injectable emulsions

    Directory of Open Access Journals (Sweden)

    Jie Peng

    2015-12-01

    Full Text Available The effect of different high pressure homogenization energy input parameters on mean diameter droplet size (MDS and droplets with > 5 μm of lipid injectable emulsions were evaluated. All emulsions were prepared at different water bath temperatures or at different rotation speeds and rotor-stator system times, and using different homogenization pressures and numbers of high-pressure system recirculations. The MDS and polydispersity index (PI value of the emulsions were determined using the dynamic light scattering (DLS method, and large-diameter tail assessments were performed using the light-obscuration/single particle optical sensing (LO/SPOS method. Using 1000 bar homogenization pressure and seven recirculations, the energy input parameters related to the rotor-stator system will not have an effect on the final particle size results. When rotor-stator system energy input parameters are fixed, homogenization pressure and recirculation will affect mean particle size and large diameter droplet. Particle size will decrease with increasing homogenization pressure from 400 bar to 1300 bar when homogenization recirculation is fixed; when the homogenization pressure is fixed at 1000 bar, the particle size of both MDS and percent of fat droplets exceeding 5 μm (PFAT5 will decrease with increasing homogenization recirculations, MDS dropped to 173 nm after five cycles and maintained this level, volume-weighted PFAT5 will drop to 0.038% after three cycles, so the “plateau” of MDS will come up later than that of PFAT5, and the optimal particle size is produced when both of them remained at plateau. Excess homogenization recirculation such as nine times under the 1000 bar may lead to PFAT5 increase to 0.060% rather than a decrease; therefore, the high-pressure homogenization procedure is the key factor affecting the particle size distribution of emulsions. Varying storage conditions (4–25°C also influenced particle size, especially the PFAT

  9. Quantifying the Impact of Immediate Reconstruction in Postmastectomy Radiation: A Large, Dose-Volume Histogram-Based Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Ohri, Nisha [Department of Radiation Oncology, Memorial Sloan-Kettering Cancer Center, New York, New York (United States); Cordeiro, Peter G. [Department of Plastic Surgery, Memorial Sloan-Kettering Cancer Center, New York, New York (United States); Keam, Jennifer [Department of Radiation Oncology, Memorial Sloan-Kettering Cancer Center, New York, New York (United States); Ballangrud, Ase [Department of Medical Physics, Memorial Sloan-Kettering Cancer Center, New York, New York (United States); Shi Weiji; Zhang Zhigang [Department of Biostatistics and Epidemiology, Memorial Sloan-Kettering Cancer Center, New York, New York (United States); Nerbun, Claire T.; Woch, Katherine M.; Stein, Nicholas F.; Zhou Ying [Department of Medical Physics, Memorial Sloan-Kettering Cancer Center, New York, New York (United States); McCormick, Beryl; Powell, Simon N. [Department of Radiation Oncology, Memorial Sloan-Kettering Cancer Center, New York, New York (United States); Ho, Alice Y., E-mail: HoA1234@mskcc.org [Department of Radiation Oncology, Memorial Sloan-Kettering Cancer Center, New York, New York (United States)

    2012-10-01

    Purpose: To assess the impact of immediate breast reconstruction on postmastectomy radiation (PMRT) using dose-volume histogram (DVH) data. Methods and Materials: Two hundred forty-seven women underwent PMRT at our center, 196 with implant reconstruction and 51 without reconstruction. Patients with reconstruction were treated with tangential photons, and patients without reconstruction were treated with en-face electron fields and customized bolus. Twenty percent of patients received internal mammary node (IMN) treatment. The DVH data were compared between groups. Ipsilateral lung parameters included V20 (% volume receiving 20 Gy), V40 (% volume receiving 40 Gy), mean dose, and maximum dose. Heart parameters included V25 (% volume receiving 25 Gy), mean dose, and maximum dose. IMN coverage was assessed when applicable. Chest wall coverage was assessed in patients with reconstruction. Propensity-matched analysis adjusted for potential confounders of laterality and IMN treatment. Results: Reconstruction was associated with lower lung V20, mean dose, and maximum dose compared with no reconstruction (all P<.0001). These associations persisted on propensity-matched analysis (all P<.0001). Heart doses were similar between groups (P=NS). Ninety percent of patients with reconstruction had excellent chest wall coverage (D95 >98%). IMN coverage was superior in patients with reconstruction (D95 >92.0 vs 75.7%, P<.001). IMN treatment significantly increased lung and heart parameters in patients with reconstruction (all P<.05) but minimally affected those without reconstruction (all P>.05). Among IMN-treated patients, only lower lung V20 in those without reconstruction persisted (P=.022), and mean and maximum heart doses were higher than in patients without reconstruction (P=.006, P=.015, respectively). Conclusions: Implant reconstruction does not compromise the technical quality of PMRT when the IMNs are untreated. Treatment technique, not reconstruction, is the primary

  10. Large volume TENAX {sup registered} extraction of the bioaccessible fraction of sediment-associated organic compounds for a subsequent effect-directed analysis

    Energy Technology Data Exchange (ETDEWEB)

    Schwab, K.; Brack, W. [UFZ - Helmholtz Centre or Environmental Research, Leipzig (Germany). Dept. of Effect-Directed Analysis

    2007-06-15

    Background, Aim and Scope: Effect-directed analysis (EDA) is a powerful tool for the identification of key toxicants in complex environmental samples. In most cases, EDA is based on total extraction of organic contaminants leading to an erroneous prioritization with regard to hazard and risk. Bioaccessibility-directed extraction aims to discriminate between contaminants that take part in partitioning between sediment and biota in a relevant time frame and those that are enclosed in structures, that do not allow rapid desorption. Standard protocols of targeted extraction of rapidly desorbing, and thus bioaccessible fraction using TENAX {sup registered} are based only on small amounts of sediment. In order to get sufficient amounts of extracts for subsequent biotesting, fractionation, and structure elucidation a large volume extraction technique needs to be developed applying one selected extraction time and excluding toxic procedural blanks. Materials and Methods: Desorption behaviour of sediment contaminants was determined by a consecutive solid-solid extraction of sediment using TENAX {sup registered} fitting a tri-compartment model on experimental data. Time needed to remove the rapidly desorbing fraction trap was calculated to select a fixed extraction time for single extraction procedures. Up-scaling by about a factor of 100 provided a large volume extraction technique for EDA. Reproducibility and comparability to small volume approach were proved. Blanks of respective TENAX {sup registered} mass were investigated using Scenedesmus vacuolatus and Artemia salina as test organisms. Results: Desorption kinetics showed that 12 to 30 % of sediment associated pollutants are available for rapid desorption. t{sub r}ap is compound dependent and covers a range of 2 to 18 h. On that basis a fixed extraction time of 24 h was selected. Validation of large volume approach was done by the means of comparison to small method and reproducibility. The large volume showed a good

  11. Preparation of magnetic anomaly profile and contour maps from DOE-NURE aerial survey data. Volume 1: Processing procedures

    Science.gov (United States)

    Tennel, E. P.; Hinze, W. J.

    1981-09-01

    Total intensity magnetic anomaly data acquired as a supplement to radiometric data in preparing regional profile and contour maps are discussed. Survey contractor supplied magnetic anomaly data are subjected to a multiprocess, computer based procedure. This procedure is used to produce the following machine plotted maps: (1) profile map of contractor supplied magnetic anomaly data; (2) profile map of high cut filtered data with contour levels of each profile marked and annotated on the associated flight track; (3) profile map of critical point data with contour levels indicated; and (4) contour map of filtered and selected data.

  12. Design aspects of a compact, single-frequency, permanent magnet ECR ion source with a large uniformly distributed resonant plasma volume

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Y.; Alton, G.D.; Mills, G.D.; Reed, C.A.; Haynes, D.L.

    1997-09-01

    A compact, all-permanent-magnet single-frequency ECR ion source with a large uniformly distributed ECR plasma volume has been designed and is presently under construction at the Oak Ridge National Laboratory (ORNL). The central region of the field is designed to achieve a flat-field (constant mod-B) which extends over the length of the central field region along the axis of symmetry and radially outward to form a uniformly distributed ECR plasma volume. The magnetic field design strongly contrasts with those used in conventional ECR ion sources where the central field regions are approximately parabolic and the consequent ECR zones are surfaces. The plasma confinement magnetic field mirror has a mirror ratio B{sub max}/B{sub ECR} of slightly greater than two. The source is designed to operate at a nominal RF frequency of 6 GHz. The central flat magnetic field region can be easily adjusted by mechanical means to tune the source to the resonant conditions within the limits of 5.5 to 6.8 GHz. The RF injection system is broadband to ensure excitation of transverse electric (TE) modes so that the RF power is largely concentrated in the resonant plasma volume which lies along and surrounds the axis of symmetry of the source. Because of the much larger ECR zone, the probability for absorption of microwave power is dramatically increased thereby increasing the probability for acceleration of electrons, the electron temperature of the plasma and, consequently, the hot electron population within the plasma volume of the source. The creation of an ECR volume rather than a surface is commensurate with higher charge states and higher beam intensities within a particular charge state.

  13. Component mode synthesis and large deflection vibration of complex structures. Volume 2: Single-mode large deflection vibrations of beams and plates using finite element method

    Science.gov (United States)

    Mei, Chuh

    1987-01-01

    A finite element method is presented for the large amplitude vibrations of complex structures that can be modelled with beam and rectangular plate elements subjected to harmonic excitation. Both inplane deformation and inertia are considered in the formulation. Derivation of the harmonic force and nonlinear stiffness matrices for a beam and a rectangular plate element are presented. Solution procedures and convergence characteristics of the finite element method are described. Nonlinear response to uniform and concentrated harmonic loadings and improved nonlinear free vibration results are presented for beams and rectangular plates of various boundary conditions.

  14. Multiphase flow modelling using non orthogonal collocated finite volumes : application to fluid catalytical cracking and large scale geophysical flows.

    Science.gov (United States)

    Martin, R. M.; Nicolas, A. N.

    2003-04-01

    A modeling approach of gas solid flow, taking into account different physical phenomena such as gas turbulence and inter-particle interactions is presented. Moment transport equations are derived for the second order fluctuating velocity tensor which allow to involve practical closures based on single phase turbulence modeling on one hand and kinetic theory of granular media on the other hand. The model is applied to fluid catalytic cracking processes and explosive volcanism. In the industry as well as in the geophysical community, multiphase flows are modeled using a finite volume approach and a multicorrector algorithm in time in order to determine implicitly the pressures, velocities and volume fractions for each phase. Pressures, and velocities are generally determined at mid-half mesh step from each other following the staggered grid approach. This ensures stability and prevents oscillations in pressure. It allows to treat almost all the Reynolds number ranges for all speeds and viscosities. The disadvantages appear when we want to treat more complex geometries or if a generalized curvilinear formulation of the conservation equations is considered. Too many interpolations have to be done and accuracy is then lost. In order to overcome these problems, we use here a similar algorithm in time and a Rhie and Chow interpolation (1983) of the collocated variables and essentially the velocities at the interface. The Rhie and Chow interpolation of the velocities at the finite volume interfaces allows to have no oscillations of the pressure without checkerboard effects and to stabilize all the algorithm. In a first predictor step, fluxes at the interfaces of the finite volumes are then computed using 2nd and 3rd order shock capturing schemes of MUSCL/TVD or Van Leer type, and the orthogonal stress components are treated implicitly while cross viscous/diffusion terms are treated explicitly. Pentadiagonal linear systems are solved in each geometrical direction (the so

  15. Synthesis of Macro-Mesostructuredγ-Al2O3 with Large Pore Volume and High Surface Area by a Facile Secondary Reforming Method

    Institute of Scientific and Technical Information of China (English)

    Meng Xiuhong; Duan Linhai; Xie Xiaohua; Wang Qiang; Wang Haiyan

    2014-01-01

    Through improving the aging process during synthesis of the support,γ-Al2O3 with large pore volume and high surface area was synthesized by a facile secondary reforming method. The synthesis parameters, such as the reaction tem-perature, the ifrst aging temperature and the second aging temperature, were investigated. The textural properties ofγ-Al2O3 were characterized by means of N2 adsorption-desorption isotherms, X-ray powder diffractometry (XRD), scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy and thermogravimetry (TG). The experimental results indicated that AACH and amorphous AlOOH were the precursors of alumina, which were formed via precipitation from solutions after reaction of aluminum sulphate with ammonium hydrogen carbonate. The precursor nanocrystallites grew and re-assembled during the secondary reforming process, which resulted in an increased pore size and pore volume and a decreased bulk density. The as-synthesizedγ-Al2O3 materials featured meso/macroporosity, large pore volume (2.175 cm3/g), high surface area (237.8 m2/g), and low bulk density (0.284 g/mL).

  16. Cryo-FIB-SEM serial milling and block face imaging: Large volume structural analysis of biological tissues preserved close to their native state.

    Science.gov (United States)

    Vidavsky, Netta; Akiva, Anat; Kaplan-Ashiri, Ifat; Rechav, Katya; Addadi, Lia; Weiner, Steve; Schertel, Andreas

    2016-12-01

    Many important biological questions can be addressed by studying in 3D large volumes of intact, cryo fixed hydrated tissues (⩾10,000μm(3)) at high resolution (5-20nm). This can be achieved using serial FIB milling and block face surface imaging under cryo conditions. Here we demonstrate the unique potential of the cryo-FIB-SEM approach using two extensively studied model systems; sea urchin embryos and the tail fin of zebrafish larvae. We focus in particular on the environment of mineral deposition sites. The cellular organelles, including mitochondria, Golgi, ER, nuclei and nuclear pores are made visible by the image contrast created by differences in surface potential of different biochemical components. Auto segmentation and/or volume rendering of the image stacks and 3D reconstruction of the skeleton and the cellular environment, provides a detailed view of the relative distribution in space of the tissue/cellular components, and thus of their interactions. Simultaneous acquisition of secondary and back-scattered electron images adds additional information. For example, a serial view of the zebrafish tail reveals the presence of electron dense mineral particles inside mitochondrial networks extending more than 20μm in depth in the block. Large volume imaging using cryo FIB SEM, as demonstrated here, can contribute significantly to the understanding of the structures and functions of diverse biological tissues.

  17. [Determination of trace and ultra-trace level bromate in water by large volume sample injection with enrichment column for on-line preconcentration coupled with ion chromatography].

    Science.gov (United States)

    Liu, Jing; He, Qingqing; Yang, Lili; Hu, Enyu; Wang, Meifei

    2015-10-01

    A method for the determination of trace and ultra-trace level bromate in water by ion chromatography with large volume sample injection for on-line preconcentration was established. A high capacity Dionex IonPac AG23 guard column was simply used as the enrichment column instead of the loop for the preconcentration of bromate. High purity KOH solution used as eluent for gradient elution was on-line produced by an eluent generator automatically. The results showed that a good linear relationship of bromate was exhibited in the range of 0.05-51.2 μg/L (r ≥ 0.999 5), and the method detection limit was 0.01 μg/L. Compared with conventional sample injection, the injection volume was up to 5 mL, and the enrichment factor of this method was about 240 times. This method was successfully applied for several real samples of pure water which were purchased in the supermarket, and the recoveries of bromate were between 90%-100% with the RSDs (n = 6) of 2.1%-6.4% at two spiked levels. This method without pretreatment is simple, and of high accuracy and precision. The preconcentration can be achieved by large volume sample injection. It is suitable for the analysis of trace and ultra-trace level bromate.

  18. MIDAS prototype Multispectral Interactive Digital Analysis System for large area earth resources surveys. Volume 2: Charge coupled device investigation

    Science.gov (United States)

    Kriegler, F.; Marshall, R.; Sternberg, S.

    1976-01-01

    MIDAS is a third-generation, fast, low cost, multispectral recognition system able to keep pace with the large quantity and high rates of data acquisition from large regions with present and projected sensors. MIDAS, for example, can process a complete ERTS frame in forty seconds and provide a color map of sixteen constituent categories in a few minutes. A principal objective of the MIDAS Program is to provide a system well interfaced with the human operator and thus to obtain large overall reductions in turn-around time and significant gains in throughput. The need for advanced onboard spacecraft processing of remotely sensed data is stated and approaches to this problem are described which are feasible through the use of charge coupled devices. Tentative mechanizations for the required processing operations are given in large block form. These initial designs can serve as a guide to circuit/system designers.

  19. The dynamics and control of large flexible space structures. Volume 3, part B: The modelling, dynamics, and stability of large Earth pointing orbiting structures

    Science.gov (United States)

    Bainum, P. M.; Kumar, V. K.

    1980-01-01

    The dynamics and stability of large orbiting flexible beams, and platforms and dish type structures oriented along the local horizontal are treated both analytically and numerically. It is assumed that such structures could be gravitationally stabilized by attaching a rigid light-weight dumbbell at the center of mass by a spring loaded hinge which also could provide viscous damping. For the beam, the small amplitude inplane pitch motion, dumbbell librational motion, and the anti-symmetric elastic modes are all coupled. The three dimensional equations of motion for a circular flat plate and shallow spherical shell in orbit with a two-degree-of freedom gimballed dumbbell are also developed and show that only those elastic modes described by a single nodal diameter line are influenced by the dumbbell motion. Stability criteria are developed for all the examples and a sensitivity study of the system response characteristics to the key system parameters is carried out.

  20. Preparation of cell blocks for lung cancer diagnosis and prediction: protocol and experience of a high-volume center.

    Science.gov (United States)

    Kossakowski, Claudia A; Morresi-Hauf, Alicia; Schnabel, Philipp A; Eberhardt, Ralf; Herth, Felix J F; Warth, Arne

    2014-01-01

    Minimally invasive diagnostic techniques are increasingly being used to obtain specimens for pathological diagnosis and prediction. Referring to lung cancer, both endobronchial and endoesophageal ultrasound are used worldwide as diagnostic routine methods. Consequently, an increasing number of pathological samples are cytological and fewer are histological. On the other hand, the requirements for specific and sensitive tumor subtyping complemented by predictive analyses are steadily increasing and are an essential basis for evidence-based treatment decisions. In this article we focus on the cell block method as a helpful tool for diagnostic and predictive analyses in lung cancer and point out its advantages and disadvantages in comparison to conventional cytological and biopsy specimens. Furthermore, we retrospectively analyze the diagnostic results of the cell block method in a high-volume center over 5 years. The main advantages of cell blocks are the availability of established and validated protocols, archiving and the opportunity to have serial sections from the same specimens to provide or repeat molecular analyses. Actually, in case of tumor progression, even additional biomarkers can be tested using the original cell block when re-biopsies are not feasible. The cell block method should be considered as a reliable, complimentary approach to conventional cytological or biopsy procedures, which is helpful to fulfill the increasing requirements of high-quality diagnostics and prediction.

  1. Preparation of vitamin E loaded nanocapsules by the nanoprecipitation method: from laboratory scale to large scale using a membrane contactor.

    Science.gov (United States)

    Khayata, N; Abdelwahed, W; Chehna, M F; Charcosset, C; Fessi, H

    2012-02-28

    Vitamin E or α-tocopherol is widely used as a strong antioxidant in many medical and cosmetic applications, but is rapidly degraded, because of its light, heat and oxygen sensitivity. In this study, we applied the nanoprecipitation method to prepare vitamin E-loaded nanocapsules, at laboratory-scale and pilot-scale. We scaled-up the preparation of nanocapsule with the membrane contactor technique. The effect of several formulation variables on the vitamin E-loaded nanocapsules properties (mean diameter, zeta potential, and drug entrapment efficiency) was investigated. The optimized formulation at laboratory-scale and pilot-scale lead to the preparation of vitamin E-loaded nanocapsules with mean diameter of 165 and 172 nm, respectively, and a high encapsulation efficiency (98% and 97%, respectively).

  2. Dosimetric coverage of the prostate, normal tissue sparing, and acute toxicity with high-dose-rate brachytherapy for large prostate volumes

    Energy Technology Data Exchange (ETDEWEB)

    Yang, George; Strom, Tobin J.; Shrinath, Kushagra; Mellon, Eric A.; Fernandez, Daniel C.; Biagioli, Matthew C. [Department of Radiation Oncology, H. Lee Moffitt Cancer Center and Research Institute, Tampa, FL (United States); Wilder, Richard B., E-mail: mcbiagioli@yahoo.com [Cancer Treatment Centers of America, Newnan, GA (United States)

    2015-05-15

    Purpose: to evaluate dosimetric coverage of the prostate, normal tissue sparing, and acute toxicity with HDR brachytherapy for large prostate volumes. Materials and methods: one hundred and two prostate cancer patients with prostate volumes >50 mL (range: 5-29 mL) were treated with high-dose-rate (HDR) brachytherapy ± intensity modulated radiation therapy (IMRT) to 4,500 cGy in 25 daily fractions between 2009 and 2013. HDR brachytherapy monotherapy doses consisted of two 1,350-1,400 cGy fractions separated by 2-3 weeks, and HDR brachytherapy boost doses consisted of two 950-1,150 cGy fractions separated by 4 weeks. Twelve of 32 (38%) unfavorable intermediate risk, high risk, and very high risk patients received androgen deprivation therapy. Acute toxicity was graded according to the Common Terminology Criteria for Adverse Events (CTCAE) version 4. Results: median follow-up was 14 months. Dosimetric goals were achieved in over 90% of cases. Three of 102 (3%) patients developed Grade 2 acute proctitis. No variables were significantly associated with Grade 2 acute proctitis. Seventeen of 102 (17%) patients developed Grade 2 acute urinary retention. American Urological Association (AUA) symptom score was the only variable significantly associated with Grade 2 acute urinary retention (p-0.04). There was no ≥ Grade 3 acute toxicity. Conclusions: dosimetric coverage of the prostate and normal tissue sparing were adequate in patients with prostate volumes >50 mL. Higher pre-treatment AUA symptom scores increased the relative risk of Grade 2 acute urinary retention. However, the overall incidence of acute toxicity was acceptable in patients with large prostate volumes. (author)

  3. Dosimetric Coverage of the Prostate, Normal Tissue Sparing, and Acute Toxicity with High-Dose-Rate Brachytherapy for Large Prostate Volumes

    Directory of Open Access Journals (Sweden)

    George Yang

    2015-06-01

    Full Text Available ABSTRACTPurposeTo evaluate dosimetric coverage of the prostate, normal tissue sparing, and acute toxicity with HDR brachytherapy for large prostate volumes.Materials and MethodsOne hundred and two prostate cancer patients with prostate volumes >50 mL (range: 5-29 mL were treated with high-dose-rate (HDR brachytherapy ± intensity modulated radiation therapy (IMRT to 4,500 cGy in 25 daily fractions between 2009 and 2013. HDR brachytherapy monotherapy doses consisted of two 1,350-1,400 cGy fractions separated by 2-3 weeks, and HDR brachytherapy boost doses consisted of two 950-1,150 cGy fractions separated by 4 weeks. Twelve of 32 (38% unfavorable intermediate risk, high risk, and very high risk patients received androgen deprivation therapy. Acute toxicity was graded according to the Common Terminology Criteria for Adverse Events (CTCAE version 4.ResultsMedian follow-up was 14 months. Dosimetric goals were achieved in over 90% of cases. Three of 102 (3% patients developed Grade 2 acute proctitis. No variables were significantly associated with Grade 2 acute proctitis. Seventeen of 102 (17% patients developed Grade 2 acute urinary retention. American Urological Association (AUA symptom score was the only variable significantly associated with Grade 2 acute urinary retention (p=0.04. There was no ≥ Grade 3 acute toxicity.ConclusionsDosimetric coverage of the prostate and normal tissue sparing were adequate in patients with prostate volumes >50 mL. Higher pre-treatment AUA symptom scores increased the relative risk of Grade 2 acute urinary retention. However, the overall incidence of acute toxicity was acceptable in patients with large prostate volumes.

  4. Rapid Feedback Assessment Methods: Can We Improve Engagement and Preparation for Exams in Large-Enrollment Courses?

    Science.gov (United States)

    Cotner, Sehoya H.; Fall, Bruce A.; Wick, Susan M.; Walker, J. D.; Baepler, Paul M.

    2008-01-01

    Scratch-off immediate feedback assessment technique (IF-AT) forms and classroom response systems (clickers) can increase student engagement and interaction and help students prepare for exams by indicating the type and level of questions they will encounter. We used the IF-AT throughout the semester in three sections of a lower-division biology…

  5. BROAD SPECTRUM ANALYSIS FOR TRACE ORGANIC POLLUTANTS IN LARGE VOLUMES OF WATER BY XAD RESINS-COLUMN DESIGN-FACTS AND MYTHS.

    Science.gov (United States)

    Gibs, J.; Wicklund, A.; Suffet, I.H.

    1986-01-01

    The 'rule of thumb' that large volumes of water can be sampled for trace organic pollutants by XAD resin columns which are designed by small column laboratory studies or pure compounds is examined and shown to be a problem. A theory of multicomponent breakthrough is presented as a frame of reference to help solve the problem and develop useable criteria to aid the design of resin columns. An important part of the theory is the effect of humic substances on the breakthrough character of multicomponent chemical systems.

  6. 'Dip-sticks' calibration handles self-attenuation and coincidence effects in large-volume gamma-ray spectrometry

    CERN Document Server

    Wolterbeek, H T

    2000-01-01

    Routine gamma-spectrometric analyses of samples with low-level activities (e.g. food, water, environmental and industrial samples) are often performed in large samples, placed close to the detector. In these geometries, detection sensitivity is improved but large errors are introduced due to self-attenuation and coincidence summing. Current approaches to these problems comprise computational methods and spiked standard materials. However, the first are often regarded as too complex for practical routine use, the latter never fully match real samples. In the present study, we introduce a dip-sticks calibration as a fast and easy practical solution to this quantification problem in a routine analytical setting. In the proposed set-up, calibrations are performed within the sample itself, thus making it a broadly accessible matching-reference approach, which is principally usable for all sample matrices.

  7. Minimalistic sample preparation strategies for LC-MS quantification of large molecule biopharmaceuticals: a case study highlighting alpha-1 antitrypsin protein.

    Science.gov (United States)

    Wright, Katherine; Dufield, Dawn

    2014-01-01

    Large molecule biotherapeutics pose a distinctive bioanalytical challenge for LC-MS assay development, particularly when optimizing sample enrichment steps. Alpha-1 antitrypsin (AAT) is used as an example for highlighting large-molecule assay-development strategies. Two sensitive and selective LC-MS/MS-based quantification assays were developed. Fit-for-purpose assay qualifications for BAL and serum matrices were performed by assessing sensitivity, precision and accuracy, dilution linearity and interferences. Our approach to sample preparation focuses on optimizing the simplest methodology necessary to generate fit-for-purpose bioanalytical assays. To measure AAT protein levels in preclinical species with selectivity and increased assay sensitivity, a minimalistic sample preparation strategy was adopted that included either traditional direct digestion or a more complicated immunoprecipitation enrichment process.

  8. MIDAS, prototype Multivariate Interactive Digital Analysis System for large area earth resources surveys. Volume 1: System description

    Science.gov (United States)

    Christenson, D.; Gordon, M.; Kistler, R.; Kriegler, F.; Lampert, S.; Marshall, R.; Mclaughlin, R.

    1977-01-01

    A third-generation, fast, low cost, multispectral recognition system (MIDAS) able to keep pace with the large quantity and high rates of data acquisition from large regions with present and projected sensots is described. The program can process a complete ERTS frame in forty seconds and provide a color map of sixteen constituent categories in a few minutes. A principle objective of the MIDAS program is to provide a system well interfaced with the human operator and thus to obtain large overall reductions in turn-around time and significant gains in throughput. The hardware and software generated in the overall program is described. The system contains a midi-computer to control the various high speed processing elements in the data path, a preprocessor to condition data, and a classifier which implements an all digital prototype multivariate Gaussian maximum likelihood or a Bayesian decision algorithm. Sufficient software was developed to perform signature extraction, control the preprocessor, compute classifier coefficients, control the classifier operation, operate the color display and printer, and diagnose operation.

  9. An HTML5-Based Pure Website Solution for Rapidly Viewing and Processing Large-Scale 3D Medical Volume Reconstruction on Mobile Internet.

    Science.gov (United States)

    Qiao, Liang; Chen, Xin; Zhang, Ye; Zhang, Jingna; Wu, Yi; Li, Ying; Mo, Xuemei; Chen, Wei; Xie, Bing; Qiu, Mingguo

    2017-01-01

    This study aimed to propose a pure web-based solution to serve users to access large-scale 3D medical volume anywhere with good user experience and complete details. A novel solution of the Master-Slave interaction mode was proposed, which absorbed advantages of remote volume rendering and surface rendering. On server side, we designed a message-responding mechanism to listen to interactive requests from clients (Slave model) and to guide Master volume rendering. On client side, we used HTML5 to normalize user-interactive behaviors on Slave model and enhance the accuracy of behavior request and user-friendly experience. The results showed that more than four independent tasks (each with a data size of 249.4 MB) could be simultaneously carried out with a 100-KBps client bandwidth (extreme test); the first loading time was <12 s, and the response time of each behavior request for final high quality image remained at approximately 1 s, while the peak value of bandwidth was <50-KBps. Meanwhile, the FPS value for each client was ≥40. This solution could serve the users by rapidly accessing the application via one URL hyperlink without special software and hardware requirement in a diversified network environment and could be easily integrated into other telemedical systems seamlessly.

  10. An HTML5-Based Pure Website Solution for Rapidly Viewing and Processing Large-Scale 3D Medical Volume Reconstruction on Mobile Internet

    Directory of Open Access Journals (Sweden)

    Liang Qiao

    2017-01-01

    Full Text Available This study aimed to propose a pure web-based solution to serve users to access large-scale 3D medical volume anywhere with good user experience and complete details. A novel solution of the Master-Slave interaction mode was proposed, which absorbed advantages of remote volume rendering and surface rendering. On server side, we designed a message-responding mechanism to listen to interactive requests from clients (Slave model and to guide Master volume rendering. On client side, we used HTML5 to normalize user-interactive behaviors on Slave model and enhance the accuracy of behavior request and user-friendly experience. The results showed that more than four independent tasks (each with a data size of 249.4 MB could be simultaneously carried out with a 100-KBps client bandwidth (extreme test; the first loading time was <12 s, and the response time of each behavior request for final high quality image remained at approximately 1 s, while the peak value of bandwidth was <50-KBps. Meanwhile, the FPS value for each client was ≥40. This solution could serve the users by rapidly accessing the application via one URL hyperlink without special software and hardware requirement in a diversified network environment and could be easily integrated into other telemedical systems seamlessly.

  11. Preparation of Calibration Standards of N1-H Paralytic Shellfish Toxin Analogues by Large-Scale Culture of Cyanobacterium Anabaena circinalis (TA04

    Directory of Open Access Journals (Sweden)

    Toshiyuki Suzuki

    2011-03-01

    Full Text Available Mouse bioassay is the official testing method to quantify paralytic shellfish toxins (PSTs in bivalves. A number of alternative analytical methods have been reported. Some methods have been evaluated by a single laboratory validation. Among the different types of methods, chemical analyses are capable of identifying and quantifying the toxins, however a shortage of the necessary calibration standards hampers implementation of the chemical analyses in routine monitoring of PSTs in bivalves. In our present study, we studied preparation of major PST analogues as calibrants by large-scale cultivation of toxic freshwater cyanobacteria Anabaena circinalis TA04. The cells were steadily grown in 10 L bottle for 28 days. The primary N1-H toxins, C1/C2, were produced at a concentration of 1.3 ± 0.1 µmol/L. The intracellular and extracellular toxins occupied 80% and 20%, respectively. Over 220 µmol of the toxins was obtained from approximately 200 L of the culture over six months, demonstrating that it is sufficient to prepare saxitoxin analogues. The toxins were chemically converted to six N1-H analogues. Preparation of the analogues was carried out at relatively high yields (50–90%. The results indicate that our preparation method is useful to produce N1-H toxins. In our present study, detailed conditions for preparation of one of the rare N1-H analogues, gonyautoxin-5, were investigated.

  12. Large scale preparation and application of bacteriocins%细菌素的制备及其应用

    Institute of Scientific and Technical Information of China (English)

    方佳琪; 别怀周; 陈晓琳; 张明

    2011-01-01

    In recent years, bacteriocins that can inhibit or kill the growth of some bacteria have a wide range of practical application in food preservation, disease treatment and many other related aspects were found, and the preparation methods of bacteriocin were widely reported. This article outlines the preparation methods of bacteriocins and its application in many fields.%近年来,具有抑菌活性的细菌素被发现在食品防腐保鲜、疾病治疗和其他许多相关方面有着广泛的应用价值,各种制备细菌素的方法 也被广泛报道.本文概述了细菌素的制备方法 以及其在诸多领域中的应用.

  13. Effects of Small and Large Molecule Emulsifiers on the Characteristics of β-Carotene Nanoemulsions Prepared by High Pressure Homogenization

    Directory of Open Access Journals (Sweden)

    Like Mao

    2009-01-01

    Full Text Available Oil-in-water (O/W nanoemulsion allows the preparation of lipophilic nutrients such as carotenoids in liquid form, which may improve their bioavailability and broaden applications. In the present study, polyoxyethylene sorbitan monolaurate (Tween 20, TW-20, decaglycerol monolaurate (DML, octenyl succinate starch (OSS, whey protein isolate (WPI, and finally a blend of TW-20 and WPI (1 % by mass have been tested for the preparation of β-carotene nanoemulsions. Interfacial tension, droplet size, zeta potential, microstructures observed by atomic force microscopy (AFM, stability of the emulsion and β-carotene have been compared. Results show that nanoemulsions stabilized with TW-20 and DML had smaller droplet size, but relatively poorer stability, compared with the ones stabilized with OSS and WPI (p0.05.

  14. On Assumptions in Development of a Mathematical Model of Thermo-gravitational Convection in the Large Volume Process Tanks Taking into Account Fermentation

    Directory of Open Access Journals (Sweden)

    P. M. Shkapov

    2015-01-01

    Full Text Available The paper provides a mathematical model of thermo-gravity convection in a large volume vertical cylinder. The heat is removed from the product via the cooling jacket at the top of the cylinder. We suppose that a laminar fluid motion takes place. The model is based on the NavierStokes equation, the equation of heat transfer through the wall, and the heat transfer equation. The peculiarity of the process in large volume tanks was the distribution of the physical parameters of the coordinates that was taken into account when constructing the model. The model corresponds to a process of wort beer fermentation in the cylindrical-conical tanks (CCT. The CCT volume is divided into three zones and for each zone model equations was obtained. The first zone has an annular cross-section and it is limited to the height by the cooling jacket. In this zone the heat flow from the cooling jacket to the product is uppermost. Model equation of the first zone describes the process of heat transfer through the wall and is presented by linear inhomogeneous differential equation in partial derivatives that is solved analytically. For the second and third zones description there was a number of engineering assumptions. The fluid was considered Newtonian, viscous and incompressible. Convective motion considered in the Boussinesq approximation. The effect of viscous dissipation is not considered. The topology of fluid motion is similar to the cylindrical Poiseuille. The second zone model consists of the Navier-Stokes equations in cylindrical coordinates with the introduction of a simplified and the heat equation in the liquid layer. The volume that is occupied by an upward convective flow pertains to the third area. Convective flows do not mix and do not exchange heat. At the start of the process a medium has the same temperature and a zero initial velocity in the whole volume that allows us to specify the initial conditions for the process. The paper shows the

  15. Determining the directions of increasing the innovative potential of the region by developing innovative technologies and competences when preparing and implementing large investment projects

    Directory of Open Access Journals (Sweden)

    Timur V. Kramin

    2015-12-01

    Full Text Available Objective to determine the directions of increasing the innovative potential of a region through the development of innovative technologies and competences in the process of preparation and implementation of large investment projects in the Republic of Tatarstan. Methods methodology of project management institutional approach. Results it is proved that the main largescale directions of innovative potential development in the Republic of Tatarstan as a result of preparation and implementing of Universiade 2013 in Kazan are knowledge management information technologies risk management. It is shown that in the framework of the considered innovative areas a complete system was formed of competences of employees and managers in the fields of education trade hospitality and service. Scientific novelty the key directions were defined of increasing the innovative potential of a region through the development of innovative technologies and competences in the process of preparation and implementation of large investment projects by the example of the World Summer Student Games in Kazan in 2013. Practical significance on the basis of specific examples the authors illustrate the practiceoriented mechanism of innovative potential development of a region as a result of implementation of large investment projects. nbsp

  16. Trophic interactions among sympatric zooplanktivorous fish species in volume change conditions in a large, shallow, tropical lake

    Directory of Open Access Journals (Sweden)

    Rodrigo Moncayo-Estrada

    2011-03-01

    Full Text Available Significant reductions in the water volume of shallow lakes impose a restriction on species segregation promoting more interactions in the trophic relationships. The diets of three closely related zooplanktivorous silversides belonging to the Atherinopsidae species flock of lake Chapala , Mexico, were analyzed at two sites (Chirostoma jordani, C. labarcae, and C. consocium. Diets were described in critical shallow (August 2000 and volume recovery conditions (August 2005. Diets included mainly cladocerans (Bosmina, Ceriodaphnia, and Daphnia and copepods (Cyclops. A significant difference in diets was detected when comparing years (MRPP analysis, A = 0.22, p La reducción significativa en el volumen de agua de los lagos someros impone una restricción en la segregación de las especies y promueve una mayor interacción en las relaciones tróficas. Se analizó la dieta de tres especies cercanamente emparentadas de zooplanctívoros pertenecientes al flock de Aterinópsidos del lago de Chapala en dos sitios (Chirostoma jordani, C. labarcae y C. consocium. Las dieta fue descrita en una condición somera crítica (Agosto 2000 y en una condición de recuperación del lago (Agosto 2005. En la dieta se incluyen principalmente cladóceros (Bosmina, Ceriodaphnia y Daphnia y copépodos (Cyclops. Se detectó una diferencia significativa en la dieta cuando se comparan los años (análisis MRPP, A = 0.22, p < 0.0001 y los sitios en los diferentes años (análisis MRPP, A = 0.17, p = 0.004. De acuerdo a los valores promedio de amplitud de nicho, las especies fueron clasificadas como especialistas y consumidores intermediarios. En condiciones someras, el pequeño intervalo de la amplitud de nicho (1.72 a 3.64 y los altos valores del traslape de nicho (D = 0.64, L = 8.62 indicaron un alto potencial para una interacción explotativa inter-específica. Cuando el lago se recupera en su volumen, un incremento en el intervalo de amplitud de nicho (1.04 a 4.96 y los

  17. Automated transmission-mode scanning electron microscopy (tSEM for large volume analysis at nanoscale resolution.

    Directory of Open Access Journals (Sweden)

    Masaaki Kuwajima

    Full Text Available Transmission-mode scanning electron microscopy (tSEM on a field emission SEM platform was developed for efficient and cost-effective imaging of circuit-scale volumes from brain at nanoscale resolution. Image area was maximized while optimizing the resolution and dynamic range necessary for discriminating key subcellular structures, such as small axonal, dendritic and glial processes, synapses, smooth endoplasmic reticulum, vesicles, microtubules, polyribosomes, and endosomes which are critical for neuronal function. Individual image fields from the tSEM system were up to 4,295 µm(2 (65.54 µm per side at 2 nm pixel size, contrasting with image fields from a modern transmission electron microscope (TEM system, which were only 66.59 µm(2 (8.160 µm per side at the same pixel size. The tSEM produced outstanding images and had reduced distortion and drift relative to TEM. Automated stage and scan control in tSEM easily provided unattended serial section imaging and montaging. Lens and scan properties on both TEM and SEM platforms revealed no significant nonlinear distortions within a central field of ∼100 µm(2 and produced near-perfect image registration across serial sections using the computational elastic alignment tool in Fiji/TrakEM2 software, and reliable geometric measurements from RECONSTRUCT™ or Fiji/TrakEM2 software. Axial resolution limits the analysis of small structures contained within a section (∼45 nm. Since this new tSEM is non-destructive, objects within a section can be explored at finer axial resolution in TEM tomography with current methods. Future development of tSEM tomography promises thinner axial resolution producing nearly isotropic voxels and should provide within-section analyses of structures without changing platforms. Brain was the test system given our interest in synaptic connectivity and plasticity; however, the new tSEM system is readily applicable to other biological systems.

  18. Obesity is associated with larger prostate volume but not with worse urinary symptoms: analysis of a large multiethnic cohort.

    Science.gov (United States)

    Bhindi, Bimal; Margel, David; Trottier, Greg; Hamilton, Robert J; Kulkarni, Girish S; Hersey, Karen M; Finelli, Antonio; Trachtenberg, John; Zlotta, Alexandre; Toi, Ants; Evans, Andrew; van der Kwast, Theodorus; Fleshner, Neil E

    2014-01-01

    To evaluate the associations between body mass index (BMI) and prostate volume (PV) and lower urinary tract symptoms in a multiethnic cohort. A cohort of men without prostate cancer seen at our institution was assembled, excluding those with previous transurethral resection of the prostate. Height and weight were measured to compute BMI, PV was measured by transrectal ultrasound, and the International Prostate Symptom Score (IPSS) questionnaire was administered. After stratified bivariate analyses, multiple linear regression and ordinal logistic regression models were used to assess the independent effect of BMI on PV and IPSS, respectively. The cohort included 1613 patients, and mean BMI was 27.1 kg/m(2). Patients with a BMI of obese men. There were no significant differences in IPSS or usage of benign prostatic hyperplasia medications between BMI categories. In multivariable analyses, higher BMI was associated with larger PV (P <.001) but not IPSS (P = .91). On the basis of our model, given a PV of 40 mL, 50 mL, and 60 mL, each 5 kg/m(2) increase in BMI was associated with a 2.19 mL, 2.74 mL, and 3.29 mL increase in PV, respectively. Body weight (P <.001) but not height (P = .13) was associated with PV. Higher BMI is associated with larger PV but not worse lower urinary tract symptoms (measured using IPSS). Usage rate of alpha blockers or 5 alpha reductase inhibitors was not significantly different between BMI categories. Copyright © 2014 Elsevier Inc. All rights reserved.

  19. Ultrafast, sensitive and large-volume on-chip real-time PCR for the molecular diagnosis of bacterial and viral infections.

    Science.gov (United States)

    Houssin, Timothée; Cramer, Jérémy; Grojsman, Rébecca; Bellahsene, Lyes; Colas, Guillaume; Moulet, Hélène; Minnella, Walter; Pannetier, Christophe; Leberre, Maël; Plecis, Adrien; Chen, Yong

    2016-04-21

    To control future infectious disease outbreaks, like the 2014 Ebola epidemic, it is necessary to develop ultrafast molecular assays enabling rapid and sensitive diagnoses. To that end, several ultrafast real-time PCR systems have been previously developed, but they present issues that hinder their wide adoption, notably regarding their sensitivity and detection volume. An ultrafast, sensitive and large-volume real-time PCR system based on microfluidic thermalization is presented herein. The method is based on the circulation of pre-heated liquids in a microfluidic chip that thermalize the PCR chamber by diffusion and ultrafast flow switches. The system can achieve up to 30 real-time PCR cycles in around 2 minutes, which makes it the fastest PCR thermalization system for regular sample volume to the best of our knowledge. After biochemical optimization, anthrax and Ebola simulating agents could be respectively detected by a real-time PCR in 7 minutes and a reverse transcription real-time PCR in 7.5 minutes. These detections are respectively 6.4 and 7.2 times faster than with an off-the-shelf apparatus, while conserving real-time PCR sample volume, efficiency, selectivity and sensitivity. The high-speed thermalization also enabled us to perform sharp melting curve analyses in only 20 s and to discriminate amplicons of different lengths by rapid real-time PCR. This real-time PCR microfluidic thermalization system is cost-effective, versatile and can be then further developed for point-of-care, multiplexed, ultrafast and highly sensitive molecular diagnoses of bacterial and viral diseases.

  20. Large volume of water samples introduced in dispersive liquid-liquid microextraction for the determination of 15 triazole fungicides by gas chromatography-tandem mass spectrometry.

    Science.gov (United States)

    Nie, Jing; Chen, Fujiang; Song, Zhiyu; Sun, Caixia; Li, Zuguang; Liu, Wenhan; Lee, Mawrong

    2016-10-01

    A novel method of large volume of water samples directly introduced in dispersive liquid-liquid microextraction was developed, which is based on ultrasound/manual shaking-synergy-assisted emulsification and self-generating carbon dioxide gas (CO2) breaking down the emulsion for the determination of 15 triazole fungicides by gas chromatography-tandem mass spectrometry. This technique makes low-density extraction solvent toluene (180 μL) dissolve in 200 mL of samples containing 0.05 mol L(-1) of HCl and 5 % of NaCl (w/v) to form a well emulsion by synergy of ultrasound and manual shaking, and injects NaHCO3 solution (1.0 mol L(-1)) to generate CO2 achieving phase separation with the assistance of ultrasound. The entire process is accomplished within 8 min. The injection of NaHCO3 to generate CO2 achieves phase separation that breaks through the centrifugation limited large volume aqueous samples. In addition, the device could be easily cleaned, and this kind of vessel could be reconfigured for any volume of samples. Under optimal conditions, the low limits of detection ranging from 0.7 to 51.7 ng L(-1), wide linearity, and enrichment factors obtained were in the range 924-3669 for different triazole fungicides. Southern end of the Beijing-Hangzhou Grand Canal water (Hangzhou, China) was used to verify the applicability of the developed method. Graphical Abstract Flow chart of ultrasound/manual shaking-synergy-assisted emulsification and self-generating carbon dioxide gas breaking down the emulsion.

  1. A biomechanical perspective on the role of large stem volume and high water content in baobab trees (Adansonia spp.; Bombacaceae).

    Science.gov (United States)

    Chapotin, Saharah Moon; Razanameharizaka, Juvet H; Holbrook, N Michele

    2006-09-01

    The stems of large trees serve in transport, storage, and support; however, the degree to which these roles are reflected in their morphology is not always apparent. The large, water-filled stems of baobab trees (Adansonia spp.) are generally assumed to serve a water storage function, yet recent studies indicate limited use of stored water. Through an analysis of wood structure and composition, we examined whether baobab morphology reflects biomechanical constraints rather than water storage capacity in the six Madagascar baobab species. Baobab wood has a high water content (up to 79%), low wood density (0.09-0.17 g · cm(-3)), high parenchyma content (69-88%), and living cells beyond 35 cm into the xylem from the cambium. Volumetric construction cost of the wood is several times lower than in more typical trees, and the elastic modulus approaches that of parenchyma tissue. Safety factors calculated from estimated elastic buckling heights were low, indicating that baobabs are not more overbuilt than other temperate and tropical trees, yet the energy investment in stem material is comparable to that in temperate deciduous trees. Furthermore, the elastic modulus of the wood decreases with water content, such that excessive water withdrawal from the stem could affect mechanical stability.

  2. A method for rapid in situ extraction and laboratory determination of Th, Pb, and Ra isotopes from large volumes of seawater

    Science.gov (United States)

    Baskaran, M.; Murphy, David J.; Santschi, Peter H.; Orr, James C.; Schink, David R.

    1993-04-01

    An in situ pump and six channel extraction system, operating typically at 351 min -1, can not only filter seawater samples but also extract dissolved Th, Pb and Ra isotopes from large volumes of seawater at six different depths on a single lowering. By gamma counting the ash residues of three cartridges (one particle extractor and two nuclide extractors), we can determine 234Th and 210Pb concentrations in the particulate and dissolved phase. Extraction efficiencies for 234Th from the dissolved phase average 93 ± 5% and for 210Pb average ≥90%. At the same time we can determine radium isotopic ratios precisely, but, at present radium concentrations can only be established by the determination of 226Ra in a 30-1 cohort sample. This system can be deployed easily from ships having an A-frame. It eliminates the problems of transporting and processing large volumes of samples and involves relatively little manual labor and analytical time. We have tested and used this device repeatedly in the Gulf of Mexico. Our preliminary results agree well with values of 234Th and 210Pb concentrations and 228Ra/ 226Ra activity ratios reported in the literature for the Gulf of Mexico.

  3. Hydrogen production by Clostridium acetobutylicum ATCC 824 and megaplasmid-deficient mutant M5 evaluated using a large headspace volume technique

    Energy Technology Data Exchange (ETDEWEB)

    Oh, Sang-Eun [Department of Biological Environment, Kangwon National University, Kangwon-do (Korea); Zuo, Yi; Zhang, Husen [Department of Civil and Environmental Engineering, The Pennsylvania State University, University Park, PA 16802 (United States); Guiltinan, Mark J. [Department of Horticulture, The Pennsylvania State University, University Park, PA 16802 (United States); Hydrogen Energy (H2E) Center, The Pennsylvania State University, University Park, PA 16802 (United States); Logan, Bruce E.; Regan, John M. [Department of Civil and Environmental Engineering, The Pennsylvania State University, University Park, PA 16802 (United States); Hydrogen Energy (H2E) Center, The Pennsylvania State University, University Park, PA 16802 (United States)

    2009-12-15

    Biohydrogen production is measured using a variety of techniques, ranging from low cost intermittent gas release methods where yields are usually reduced due to high partial pressures of hydrogen, to expensive respirometers that can eliminate pressure buildup. A new large headspace volume technique was developed that reduces the potential for hydrogen gas inhibition without the need for a respirometer. We tested this method with two strains of clostridia, Clostridium acetobutylicum ATCC 824 and its mutant M5 that lacks a megaplasmid responsible for butanol and acetone production, and a mixed culture (heat-treated sludge). The hydrogen yield using M5 (2.64 mol-H{sub 2}/mol-glucose) was 47% higher than that of the parent strain (1.79 mol-H{sub 2}/mol-glucose), and 118% larger than that obtained in tests with the sludge inoculum (1.21 mol-H{sub 2}/mol-glucose). The increased yield for M5 was primarily due to a decrease in biomass synthesis (38%) compared to the parent strain. Hydrogen yields measured using this new method were on average 14% higher than those obtained using a conventional respirometric method. These findings indicate enhanced biohydrogen production from the megaplasmid-deficient mutant of C. acetobutylicum ATCC 824, and that an intermittent gas-sampling technique can effectively measure high hydrogen gas by using a large headspace volume. (author)

  4. Long-range and wide field of view optical coherence tomography for in vivo 3D imaging of large volume object based on akinetic programmable swept source.

    Science.gov (United States)

    Song, Shaozhen; Xu, Jingjiang; Wang, Ruikang K

    2016-11-01

    Current optical coherence tomography (OCT) imaging suffers from short ranging distance and narrow imaging field of view (FOV). There is growing interest in searching for solutions to these limitations in order to expand further in vivo OCT applications. This paper describes a solution where we utilize an akinetic swept source for OCT implementation to enable ~10 cm ranging distance, associated with the use of a wide-angle camera lens in the sample arm to provide a FOV of ~20 x 20 cm(2). The akinetic swept source operates at 1300 nm central wavelength with a bandwidth of 100 nm. We propose an adaptive calibration procedure to the programmable akinetic light source so that the sensitivity of the OCT system over ~10 cm ranging distance is substantially improved for imaging of large volume samples. We demonstrate the proposed swept source OCT system for in vivo imaging of entire human hands and faces with an unprecedented FOV (up to 400 cm(2)). The capability of large-volume OCT imaging with ultra-long ranging and ultra-wide FOV is expected to bring new opportunities for in vivo biomedical applications.

  5. Magma Chamber Model of Batur Caldera, Bali, Indonesia: Compositional Variation of Two Facies, Large-Volume Dacitic Ignimbrites

    Directory of Open Access Journals (Sweden)

    Igan S. Sutawidjaja

    2015-05-01

    Full Text Available DOI:10.17014/ijog.2.2.111-124Batur is one of the finest known calderas on Earth, and is the source of at least two major ignimbrite eruptions with a combined volume of some 84 km3 and 19 km3. These ignimbrites have a similar compositions, raising the question of whether they are geneticaly related. The Batur Ignimbrite-1 (BI-1 is crystal poor, containing rhyodacitic (68 - 70wt % SiO2, white to grey pumices and partly welded and unwelded. The overlying Batur Ignimbrite-2 (BI-2 is a homogeneous grey to black dacitic pumices (64 - 66 wt % SiO2, unwelded and densely welded (40 - 60% vesicularity, crystal and lithic rich. Phase equilibria indicate that the Batur magma equilibrated at temperatures of 1100 - 1300oC with melt water contents of 3 - 6 wt%. The post-eruptive Batur magma was cooler (<1100oC and it is melt more water rich (> 6 wt % H2O. A pressure of 20 kbar is infered from mineral barometry for the Batur magma chamber. Magmatic chamber model is one in which crystals and melt separate from a convecting Batur magma by density differences, resulting in a stratified magma chamber with a homogeneous central zone, a crystal-rich accumulation zone near the walls or base, and a buoyant, melt-rich zone near the top. This is consistent with the estimated magma temperatures and densities: the pre-eruptive BI-1 magma was hoter (1300oC and more volatile rich (6 wt % H2O with density 2.25 g/cm3 than the BI-2 magma (1200oC; 4 wt % H2O in density was higher (2.50 g/cm3. Batur melt characteristics and intensive parameters are consistent with a volatile oversaturation-driven eruption. However, the higher H2O content, high viscosity and low crystal content of the BI-1 magma imply an external eruption trigger.

  6. Determination of nifuroxazide in biological fluids by automated high-performance liquid chromatography with large-volume injection.

    Science.gov (United States)

    Guinebault, P R; Broquaire, M; Braithwaite, R A

    1981-01-16

    A high-performance liquid chromatographic method for the measurement of nifuroxazide in plasma is described. The technique is based on the single extraction of the drug from buffered plasma with chloroform, using nifuratel as internal standard. The chromatographic system consisted of a 15 cm x 4.6 mm I.D. stainless-steel column packed with Spherisorb ODS, 5 micrometer, and the mobile phase was acetonitrile-orthophosphoric acid (pH 2.5) (30:70). The method was able to measure accurately plasma nifuroxazide concentrations down to 2 ng . ml-1 using 2 ml of sample with no interference from endogenous compounds. The coefficients of variation of the method at 200 and 2 ng . ml-1 were 3% and 15%, respectively, and the calibration graph was linear in this range. The use of automatic injection makes the method suitable for the routine analysis of large numbers of samples.

  7. Facile preparation of polypyrrole/graphene oxide nanocomposites with large areal capacitance using electrochemical codeposition for supercapacitors

    Science.gov (United States)

    Zhou, Haihan; Han, Gaoyi; Xiao, Yaoming; Chang, Yunzhen; Zhai, Hua-Jin

    2014-10-01

    A simple and low-cost electrochemical codeposition method has been introduced to fabricate polypyrrole/graphene oxide (PPy/GO) nanocomposites and the areal capacitance of conducting polymer/GO composites is reported for the first time. Fourier transform infrared spectroscopy (FTIR), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XRD) are implemented to determine the PPy/GO nanocomposites are successfully prepared and the interaction between PPy and GO. The as-prepared PPy/GO nanocomposites show the curly sheet-like morphology, superior capacitive behaviors and cyclic stability. Furthermore, the varying deposition time is implemented to investigate the impact of the loading amount on electrochemical behavior of the composites, and a high areal capacitance of 152 mF cm-2 is achieved at 10 mV s-1 CV scan. However, the thicker films caused by the long deposition time would result in larger diffusion resistance of electrolyte ions, consequently exhibit the relatively lower capacitance value at the high current density. The GCD tests indicate moderate deposition time is more suitable for the fast charge/discharge. Considering the very simple and effective synthetic process, the PPy/GO nanocomposites with relatively high areal capacitance are competitive candidate for supercapacitor application, and its capacitive performances can be easily tuned by varying the deposition time.

  8. JUICE: a data management system that facilitates the analysis of large volumes of information in an EST project workflow

    Directory of Open Access Journals (Sweden)

    Martinez Veronica

    2006-11-01

    Full Text Available Abstract Background Expressed sequence tag (EST analyses provide a rapid and economical means to identify candidate genes that may be involved in a particular biological process. These ESTs are useful in many Functional Genomics studies. However, the large quantity and complexity of the data generated during an EST sequencing project can make the analysis of this information a daunting task. Results In an attempt to make this task friendlier, we have developed JUICE, an open source data management system (Apache + PHP + MySQL on Linux, which enables the user to easily upload, organize, visualize and search the different types of data generated in an EST project pipeline. In contrast to other systems, the JUICE data management system allows a branched pipeline to be established, modified and expanded, during the course of an EST project. The web interfaces and tools in JUICE enable the users to visualize the information in a graphical, user-friendly manner. The user may browse or search for sequences and/or sequence information within all the branches of the pipeline. The user can search using terms associated with the sequence name, annotation or other characteristics stored in JUICE and associated with sequences or sequence groups. Groups of sequences can be created by the user, stored in a clipboard and/or downloaded for further analyses. Different user profiles restrict the access of each user depending upon their role in the project. The user may have access exclusively to visualize sequence information, access to annotate sequences and sequence information, or administrative access. Conclusion JUICE is an open source data management system that has been developed to aid users in organizing and analyzing the large amount of data generated in an EST Project workflow. JUICE has been used in one of the first functional genomics projects in Chile, entitled "Functional Genomics in nectarines: Platform to potentiate the competitiveness of Chile in

  9. JUICE: a data management system that facilitates the analysis of large volumes of information in an EST project workflow.

    Science.gov (United States)

    Latorre, Mariano; Silva, Herman; Saba, Juan; Guziolowski, Carito; Vizoso, Paula; Martinez, Veronica; Maldonado, Jonathan; Morales, Andrea; Caroca, Rodrigo; Cambiazo, Veronica; Campos-Vargas, Reinaldo; Gonzalez, Mauricio; Orellana, Ariel; Retamales, Julio; Meisel, Lee A

    2006-11-23

    Expressed sequence tag (EST) analyses provide a rapid and economical means to identify candidate genes that may be involved in a particular biological process. These ESTs are useful in many Functional Genomics studies. However, the large quantity and complexity of the data generated during an EST sequencing project can make the analysis of this information a daunting task. In an attempt to make this task friendlier, we have developed JUICE, an open source data management system (Apache + PHP + MySQL on Linux), which enables the user to easily upload, organize, visualize and search the different types of data generated in an EST project pipeline. In contrast to other systems, the JUICE data management system allows a branched pipeline to be established, modified and expanded, during the course of an EST project. The web interfaces and tools in JUICE enable the users to visualize the information in a graphical, user-friendly manner. The user may browse or search for sequences and/or sequence information within all the branches of the pipeline. The user can search using terms associated with the sequence name, annotation or other characteristics stored in JUICE and associated with sequences or sequence groups. Groups of sequences can be created by the user, stored in a clipboard and/or downloaded for further analyses. Different user profiles restrict the access of each user depending upon their role in the project. The user may have access exclusively to visualize sequence information, access to annotate sequences and sequence information, or administrative access. JUICE is an open source data management system that has been developed to aid users in organizing and analyzing the large amount of data generated in an EST Project workflow. JUICE has been used in one of the first functional genomics projects in Chile, entitled "Functional Genomics in nectarines: Platform to potentiate the competitiveness of Chile in fruit exportation". However, due to its ability to

  10. The large-volume high-pressure facility at GSECARS: A 'Swiss-army-knife' approach to synchrotron-based experimental studies

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yanbin; Rivers, Mark; Sutton, Steve; Nishiyama, Norimasa; Uchida, Takeyuki; Sanehira, Takeshi; (UC)

    2009-06-01

    A number of new techniques have been developed at the large-volume press (LVP) high-pressure facility at the GeoSoilEnviroCARS (GSECARS) sector of the advanced photon source (APS). This article describes the 10 MN (1000 T) and 2.5 MN (250 T) hydraulic presses in the insertion device (ID) and bending magnet (BM) beamlines, respectively, with several apparatus and various diffraction and imaging techniques developed since the inception of the facility. Several Kawai-type high-pressure modules, whose second-stage anvils range from 10 mm to 25.4 mm in edge lengths, are used in the hydraulic presses, with pressure (P) and temperature (T) capabilities up to 30 GPa and 3000 K. A DIA-type apparatus can be compressed in both presses for studies requiring large sample volumes. A deformation DIA (D-DIA) has been developed to allow controlled deformation studies on both crystalline and glass materials, using monochromatic diffraction and imaging, up to 20 GPa and 1800 K. A high-pressure tomography apparatus is available for conducting tomography studies at high P and T, with a typical spatial resolution of a few micrometers. Toroidal anvil modules provide large 2{theta} angles for studies of non-crystalline materials, and a new large D-DIA module is under construction for double-stage megabar pressure generation as well as deformation on large samples with the capability of acoustic emission detection. The flexible design of the monochromator at the BM beamline makes it feasible to switch between monochromatic and white-beam mode during an experiment, ideal for monochromatic imaging studies (e.g., high-P tomography) with energy-dispersive diffraction for pressure measurements. A new angle-dispersive diffraction technique has been developed for high P-T crystallography studies, where a solid-state detector is step-scanned, thereby collecting a large number of angle-dispersive spectra over a wide range of photon energies recorded in the multi-channel analyzer. An ultrasonic

  11. Environmental Monitoring and Characterization of Radiation Sources on UF Campus Using a Large Volume NaI Detector

    Science.gov (United States)

    Bruner, Jesse A.; Gardiner, Hannah E.; Jordan, Kelly A.; Baciak, James E.

    2016-09-01

    Environmental radiation surveys are important for applications such as safety and regulations. This is especially true for areas exposed to emissions from nuclear reactors, such as the University of Florida Training Reactor (UFTR). At the University of Florida, surveys are performed using the RSX-1 NaI detector, developed by Radiation Solutions Inc. The detector uses incoming gamma rays and an Advanced Digital Spectrometer module to produce a linear energy spectrum. These spectra can then be analyzed in real time with a personal computer using the built in software, RadAssist. We report on radiation levels around the University of Florida campus using two mobile detection platforms, car-borne and cart-borne. The car-borne surveys provide a larger, broader map of campus radiation levels. On the other hand, cart-borne surveys provide a more detailed radiation map because of its ability to reach places on campus cars cannot go. Throughout the survey data, there are consistent radon decay product energy peaks in addition to other sources such as medical I-131 found in a large crowd of people. Finally, we investigate further applications of this mobile detection platform, such as tracking the Ar-41 plume emitted from the UFTR and detection of potential environmental hazards.

  12. Thin films of spin-crossover coordination polymers with large thermal hysteresis loops prepared by nanoparticle spin coating.

    Science.gov (United States)

    Tanaka, Daisuke; Aketa, Naoki; Tanaka, Hirofumi; Tamaki, Takashi; Inose, Tomoko; Akai, Tomoki; Toyama, Hirotaka; Sakata, Osami; Tajiri, Hiroo; Ogawa, Takuji

    2014-09-11

    This communication describes the synthesis of spin-crossover nanoparticles, which can disperse in various organic solvents without an excess amount of surfactants. The nanoparticles form homogeneous thin films on substrates by spin coating. The films show abrupt spin transitions with large thermal hysteresis loops.

  13. Large-scale preparation of clove essential oil and eugenol-loaded liposomes using a membrane contactor and a pilot plant.

    Science.gov (United States)

    Sebaaly, Carine; Greige-Gerges, Hélène; Agusti, Géraldine; Fessi, Hatem; Charcosset, Catherine

    2016-01-01

    Based on our previous study where optimal conditions were defined to encapsulate clove essential oil (CEO) into liposomes at laboratory scale, we scaled-up the preparation of CEO and eugenol (Eug)-loaded liposomes using a membrane contactor (600 mL) and a pilot plant (3 L) based on the principle of ethanol injection method, both equipped with a Shirasu Porous Glass membrane for injection of the organic phase into the aqueous phase. Homogenous, stable, nanometric-sized and multilamellar liposomes with high phospholipid, Eug loading rates and encapsulation efficiency of CEO components were obtained. Saturation of phospholipids and drug concentration in the organic phase may control the liposome stability. Liposomes loaded with other hydrophobic volatile compounds could be prepared at large scale using the ethanol injection method and a membrane for injection.

  14. Pre-column dilution large volume injection ultra-high performance liquid chromatography-tandem mass spectrometry for the analysis of multi-class pesticides in cabbages.

    Science.gov (United States)

    Zhong, Qisheng; Shen, Lingling; Liu, Jiaqi; Yu, Dianbao; Li, Siming; Yao, Jinting; Zhan, Song; Huang, Taohong; Hashi, Yuki; Kawano, Shin-ichi; Liu, Zhaofeng; Zhou, Ting

    2016-04-15

    Pre-column dilution large volume injection (PD-LVI), a novel sample injection technique for reverse phase ultra-high performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS), was developed in this study. The PD-LVI UHPLC-MS/MS system was designed by slightly modifying the commercial UHPLC-MS/MS equipment with a mixer chamber. During the procedure of PD-LVI, sample solution of 200μL was directly carried by the organic mobile phase to the mixer and diluted with the aqueous mobile phase. After the mixture was introduced to the UHPLC column in a mobile phase of acetonitrile-water (15/85, v/v), the target analytes were stacked on the head of the column until following separation. Using QuEChERS extraction, no additional steps such as solvent evaporation or residue redissolution were needed before injection. The features of PD-LVI UHPLC-MS/MS system were systematically investigated, including the injection volume, the mixer volume, the precondition time and the gradient elution. The efficiency of this approach was demonstrated by direct analysis of 24 pesticides in cabbages. Under the optimized conditions, low limits of detection (0.00074-0.8 ng/kg) were obtained. The recoveries were in the range of 63.3-109% with relative standard deviations less than 8.1%. Compared with common UHPLC-MS/MS technique, PD-LVI UHPLC-MS/MS showed significant advantages such as excellent sensitivity and reliability. The mechanism of PD-LVI was demonstrated to be based on the column-head stacking effect with pre-column dilution. Based on the results, PD-LVI as a simple and effective sample injection technique of reverse phase UHPLC-MS/MS for the analysis of trace analytes in complex samples showed a great promising prospect.

  15. Highly selective solid-phase extraction and large volume injection for the robust gas chromatography-mass spectrometric analysis of TCA and TBA in wines.

    Science.gov (United States)

    Insa, S; Anticó, E; Ferreira, V

    2005-09-30

    A reliable solid-phase extraction (SPE) method for the simultaneous determination of 2,4,6-trichloroanisole (TCA) and 2,4,6-tribromoanisole (TBA) in wines has been developed. In the proposed procedure 50 mL of wine are extracted in a 1 mL cartridge filled with 50 mg of LiChrolut EN resins. Most wine volatiles are washed up with 12.5 mL of a water:methanol solution (70%, v/v) containing 1% of NaHCO3. Analytes are further eluted with 0.6 mL of dichloromethane. A 40 microL aliquot of this extract is directly injected into a PTV injector operated in the solvent split mode, and analysed by gas chromatography (GC)-ion trap mass spectrometry using the selected ion storage mode. The solid-phase extraction, including sample volume and rinsing and elution solvents, and the large volume GC injection have been carefully evaluated and optimized. The resulting method is precise (RSD (%) extract is clean, simple and free from non-volatiles).

  16. Microwave-assisted extraction and large-volume injection gas chromatography tandem mass spectrometry determination of multiresidue pesticides in edible seaweed.

    Science.gov (United States)

    García-Rodríguez, D; Carro, A M; Cela, R; Lorenzo, R A

    2010-09-01

    A microwave-assisted extraction method followed by clean-up with solid-phase extraction (SPE) combined with large-volume injection gas chromatography-tandem mass spectrometry (LVI-GC-MS/MS) for the analysis of 17 pesticides in wild and aquaculture edible seaweeds has been developed. An experimental central composite design was employed to evaluate the effects of the main variables potentially affecting the extraction (temperature, time, and solvent volume) and to optimize the process. The most effective microwave extraction conditions were achieved at 125 °C and 12 min with 24 mL of hexane/ethyl acetate (80:20). SPE clean-up of the extracts with graphitized carbon and Florisil, optimized by means of the experimental design, proved to be efficient in the removal of matrix interferences. The analytical recoveries were close to 100% for all the analytes, with relative standard deviations lower than 13%. The limits of detection ranged from 0.3 to 23.1 pg g(-1) and the limits of quantification were between 2.3 and 76.9 pg g(-1), far below the maximum residue levels established by the European Union for pesticides in seaweed. The results obtained prove the suitability of the microwave-assisted extraction for the routine analysis of pesticides in aquaculture and wild seaweed samples.

  17. Large-scale three-dimensional phase-field simulations for phase coarsening at ultrahigh volume fraction on high-performance architectures

    Science.gov (United States)

    Yan, Hui; Wang, K. G.; Jones, Jim E.

    2016-06-01

    A parallel algorithm for large-scale three-dimensional phase-field simulations of phase coarsening is developed and implemented on high-performance architectures. From the large-scale simulations, a new kinetics in phase coarsening in the region of ultrahigh volume fraction is found. The parallel implementation is capable of harnessing the greater computer power available from high-performance architectures. The parallelized code enables increase in three-dimensional simulation system size up to a 5123 grid cube. Through the parallelized code, practical runtime can be achieved for three-dimensional large-scale simulations, and the statistical significance of the results from these high resolution parallel simulations are greatly improved over those obtainable from serial simulations. A detailed performance analysis on speed-up and scalability is presented, showing good scalability which improves with increasing problem size. In addition, a model for prediction of runtime is developed, which shows a good agreement with actual run time from numerical tests.

  18. Large pore volume mesoporous copper particles and scaffold microporous carbon material obtained from an inorganic-organic nanohybrid material, copper-succinate-layered hydroxide.

    Science.gov (United States)

    Ghotbi, Mohammad Yeganeh; Bagheri, Narjes; Sadrnezhaad, S K

    2011-10-01

    Copper-succinate-layered hydroxide (CSLH), a new nanohybrid material, was synthesized as an inorganic-organic nanohybrid, in which organic moiety was intercalated between the layers of a single cation layered material, copper hydroxide nitrate. Microporous scaffold carbon material was obtained by thermal decomposition of the nanohybrid at 500 °C under argon atmosphere followed by acid washing process. Furthermore, the heat-treated product of the nanohybrid at 600 °C was ultrafine mesoporous metallic copper particles. The results of this study confirmed the great potential of CSLH to produce the carbon material with large surface area (580 m(2)/g) and high pore volume copper powder (2.04 cm(3)/g).

  19. Synchrotron radiation studies of spectral response features caused by Te inclusions in a large volume coplanar grid CdZnTe detector

    CERN Document Server

    Hansson, Conny C T; Quarati, Francesco; Kozorezov, Alexander; Gostilo, Vladimir; Lumb, David

    2011-01-01

    We report preliminary results from a synchrotron radiation study of Te inclusions in a large volume single crystal CdZnTe (CZT) coplanar-grid detector. The experiment was carried out by probing individual inclusions with highly collimated monochromatic X-and gamma-ray beams. It was found that for shallow X-ray interaction depths, the effect of an inclusion on measured energy loss spectra is to introduce a ~10% shift in the peak centroid energy towards lower channel numbers. The total efficiency is however not affected, showing that the net result of inclusions is a reduction in the Charge Collection Efficiency (CCE). For deeper interaction depths, the energy-loss spectra shows the emergence of two distinct peaks, both downshifted in channel number. We note that the observed spectral behavior shows strong similarities with that reported in semiconductors which exhibit polarization effects, suggesting that the underlying mechanism is common.

  20. Large-volume constant-concentration sampling technique coupling with surface-enhanced Raman spectroscopy for rapid on-site gas analysis

    Science.gov (United States)

    Zhang, Zhuomin; Zhan, Yisen; Huang, Yichun; Li, Gongke

    2017-08-01

    In this work, a portable large-volume constant-concentration (LVCC) sampling technique coupling with surface-enhanced Raman spectroscopy (SERS) was developed for the rapid on-site gas analysis based on suitable derivatization methods. LVCC sampling technique mainly consisted of a specially designed sampling cell including the rigid sample container and flexible sampling bag, and an absorption-derivatization module with a portable pump and a gas flowmeter. LVCC sampling technique allowed large, alterable and well-controlled sampling volume, which kept the concentration of gas target in headspace phase constant during the entire sampling process and made the sampling result more representative. Moreover, absorption and derivatization of gas target during LVCC sampling process were efficiently merged in one step using bromine-thiourea and OPA-NH4+ strategy for ethylene and SO2 respectively, which made LVCC sampling technique conveniently adapted to consequent SERS analysis. Finally, a new LVCC sampling-SERS method was developed and successfully applied for rapid analysis of trace ethylene and SO2 from fruits. It was satisfied that trace ethylene and SO2 from real fruit samples could be actually and accurately quantified by this method. The minor concentration fluctuations of ethylene and SO2 during the entire LVCC sampling process were proved to be samples were achieved in range of 95.0-101% and 97.0-104% respectively. It is expected that portable LVCC sampling technique would pave the way for rapid on-site analysis of accurate concentrations of trace gas targets from real samples by SERS.

  1. Large-volume constant-concentration sampling technique coupling with surface-enhanced Raman spectroscopy for rapid on-site gas analysis.

    Science.gov (United States)

    Zhang, Zhuomin; Zhan, Yisen; Huang, Yichun; Li, Gongke

    2017-08-05

    In this work, a portable large-volume constant-concentration (LVCC) sampling technique coupling with surface-enhanced Raman spectroscopy (SERS) was developed for the rapid on-site gas analysis based on suitable derivatization methods. LVCC sampling technique mainly consisted of a specially designed sampling cell including the rigid sample container and flexible sampling bag, and an absorption-derivatization module with a portable pump and a gas flowmeter. LVCC sampling technique allowed large, alterable and well-controlled sampling volume, which kept the concentration of gas target in headspace phase constant during the entire sampling process and made the sampling result more representative. Moreover, absorption and derivatization of gas target during LVCC sampling process were efficiently merged in one step using bromine-thiourea and OPA-NH4(+) strategy for ethylene and SO2 respectively, which made LVCC sampling technique conveniently adapted to consequent SERS analysis. Finally, a new LVCC sampling-SERS method was developed and successfully applied for rapid analysis of trace ethylene and SO2 from fruits. It was satisfied that trace ethylene and SO2 from real fruit samples could be actually and accurately quantified by this method. The minor concentration fluctuations of ethylene and SO2 during the entire LVCC sampling process were proved to be samples were achieved in range of 95.0-101% and 97.0-104% respectively. It is expected that portable LVCC sampling technique would pave the way for rapid on-site analysis of accurate concentrations of trace gas targets from real samples by SERS. Copyright © 2017 Elsevier B.V. All rights reserved.

  2. A retrospective study on the use of a low-molecular-weight heparin for thromboembolism prophylaxis in large-volume liposuction and body contouring procedures.

    Science.gov (United States)

    Newall, Germán; Ruiz-Razura, Amado; Mentz, Henry A; Patronella, Christopher K; Ibarra, Francis R; Zarak, Alberto

    2006-01-01

    This retrospective study was designed to evaluate the efficacy of low-molecular-weight heparin (enoxeparin) as a prophylaxis for venous thromboembolism and deep venous thrombosis (DVT) in the management of large-volume liposuction, added body-contouring procedures, or both. The author present an 18-month experience with the use of this therapy for 291 consecutive patients. All the patients fell into the categories of high risk and highest risk for the development of deep vein thrombosis, embolism, or both. Three patients experienced transient DVT-like symptoms and underwent a thorough workup by an independent highly specialized critical care medical team. The results were found ultimately to be inconclusive for DVT and pulmonary embolism. However, all the patients experienced a complete recovery. The results show a 0% incidence of DVT and pulmonary embolism among patients who received enoxeparin as prophylaxis. The medication did not precipitate major bleeding when administered 1 h after surgery. This study offers the first report that describes the use of enoxeparin in aesthetic surgery for high-risk patients. The authors feel the need to inform their colleagues of the benefits obtained over the past 18 months by incorporating this therapy in large-volume liposuction and extensive body-contouring procedures performed during the same operative session. This study was conducted by a highly experienced surgical team in a fully accredited outpatient facility with established protocols for handling these types of procedures on a daily basis. The authors are optimistic about the results, and the use of enoxeparin is now part of their postoperative regimen in high-risk aesthetic surgery cases.

  3. Geochronology, geochemistry, and tectonic characterization of Quaternary large-volume travertine deposits in the southwestern United States and their implications for CO2 sequestration

    Science.gov (United States)

    Priewisch, Alexandra

    Travertines are freshwater carbonates that precipitate from carbonic groundwater due to the degassing of CO2. Travertine deposits are often situated along faults that serve as conduits for CO2-charged groundwater and their geochemistry often records mixing of deeply-derived fluids and volatiles with shallow meteoric water. Travertines are surface expressions of dynamic mantle processes related to the tectonic setting. This dissertation includes four chapters that focus on different aspects of travertine formation and their scientific value. They are excellent, although underestimated, diagnostic tools for climatology, hydrology, tectonics, geochemistry, geomicrobiology, and they can inform carbon sequestration models. Quaternary large-volume travertine deposits in New Mexico and Arizona occur in an extensional tectonic stress regime on the southeastern Colorado Plateau and along the Rio Grande rift. They accumulated above fault systems during episodes of high hydraulic head in confined aquifers, increased regional volcanic activity, and high input of mantle-derived volatiles such as CO 2 and He. Stable isotope and trace element geochemistry of travertines is controlled by groundwater geochemistry as well as the degassing of CO 2. The geochemical composition allows for distinguishing different travertine facies and evaluating past groundwater flow. The travertine deposits in New Mexico are interpreted to be extinct CO2 fields due to the large volumes that accumulated and in analogy to the travertine deposits in Arizona that are associated with an active CO2-gas field. Travertines are natural analogues for CO2 leakage along fault systems that bypassed regional cap rocks and they provide important insight into the migration of CO2 from a reservoir to the surface. The volume of travertine can be used to infer the integrated CO2 leakage along a fault system over geologic time. This leakage is estimated as: (1) CO2 that becomes fixed in CaCO3/travertine (tons of carbon

  4. Radio-chemical dosage of {sup 90}Sr in large volumes of drinking water; Dosage radiochimique du {sup 90}Sr sur des volumes importants d'eaux potables

    Energy Technology Data Exchange (ETDEWEB)

    Jeanmaire, L.; Patti, F.; Bullier, D. [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1965-07-01

    I. Principle of the method: 1. Fixing on a resin of all the cations present in the water. 2. Elution using 5 N nitric acid and precipitation of strontium as the carbonate. 3. Concentration of the strontium using the fuming nitric acid method. 4. Purification of the strontium on a resin by selective elution with ammonium citrate. 5. The strontium-90 is measured by separation at the {sup 90}Y equilibrium in the form of the oxalate which is then counted. II. Advantages of the method The concentration of the radio-activity starting from large volumes (100 l) is generally tedious but this method which makes use of a fixation on a cationic resin makes it very simple. The rest of the method consists of a series of simple chemical operations using ion-exchange on resins and coprecipitation. Finally, it is possible to dose stable strontium. (authors) [French] I. Principe du dosage 1. Fixation sur resine de tous les cations presents dans l'eau, 2. Elution par l'acide nitrique 5 N et precipitation du strontium sous forme de carbonate. 3. Concentration du strontium par la methode a l'acide nitrique fumant. 4. Purification du strontium sur resine par elution selective au citrate d'ammonium. 5. Le strontium-90 est dose par separation a l'equilibre du {sup 90}Y sous forme d'oxalate qui est compte. II. Interet de la methode La concentration de la radioactivite a partir de volumes importants (100 l) est generalement fastidieuse, la technique proposee rend cette phase tres simple en utilisant une fixation sur resine cationique. Le reste de la technique est une suite d'operations chimiques simples a realiser, faisant appel a l'echange d'ions sur resine et a la coprecipitation. Enfin, il est possible de realiser le dosage du strontium stable. (auteurs)

  5. Preparation and Characterization of a Master Blend of Plutonium Oxide for the 3013 Large Scale Shelf-Life Surveillance Project

    Energy Technology Data Exchange (ETDEWEB)

    Gillispie, Obie William [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Worl, Laura Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Veirs, Douglas Kirk [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stroud, Mary Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Narlesky, Joshua Edward [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Berg, John M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Kelly, Elizabeth J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Padilla, Dennis D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Bender, Beverly [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Lopez, Annabelle S. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Martinex, Max A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Trujillo, Leonardo A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Wilson, Edward L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-04-10

    A mixture of chlorine-containing, impure plutonium oxides has been produced and has been given the name Master Blend. This large quantity of well-characterized chlorinecontaining material is available for use in the Integrated Surveillance and Monitoring Program for shelf-life experiments. It is intended to be representative of materials packaged to meet DOE-STD-3013.1 The Master Blend contains a mixture of items produced in Los Alamos National Laboratory’s (LANL) electro-refining pyrochemical process in the late 1990s. Twenty items were crushed and sieved, calcined to 800ºC for four hours, and blended multiple times. This process resulted in four batches of Master Blend. Calorimetry and density data on material from the four batches indicate homogeneity.

  6. Facile preparation of monodisperse, impurity-free, and antioxidation copper nanoparticles on a large scale for application in conductive ink.

    Science.gov (United States)

    Zhang, Yu; Zhu, Pengli; Li, Gang; Zhao, Tao; Fu, Xianzhu; Sun, Rong; Zhou, Feng; Wong, Ching-ping

    2014-01-08

    Monodisperse copper nanoparticles with high purity and antioxidation properties are synthesized quickly (only 5 min) on a large scale (multigram amounts) by a modified polyol process using slightly soluble Cu(OH)2 as the precursor, L-ascorbic acid as the reductant, and PEG-2000 as the protectant. The resulting copper nanoparticles have a size distribution of 135 ± 30 nm and do not suffer significant oxidation even after being stored for 30 days under ambient conditions. The copper nanoparticles can be well-dispersed in an oil-based ink, which can be silk-screen printed onto flexible substrates and then converted into conductive patterns after heat treatment. An optimal electrical resistivity of 15.8 μΩ cm is achieved, which is only 10 times larger than that of bulk copper. The synthesized copper nanoparticles could be considered as a cheap and effective material for printed electronics.

  7. Large coercivity FePt nanoparticles prepared via a one-step method without post-annealing

    Science.gov (United States)

    Zhang, Xinwei; Xiong, Fang; Jiang, Xiaohong; Hua, Zhenghe; Wang, Chunlei; Yang, Shaoguang

    2016-12-01

    L10 FePt nanoparticles were synthesized by a one-step sol-gel autocombustion method, using nontoxic ferric nitrate, hexachloroplatinic acid, and glycine as starting materials. In contrast to common syntheses, high-temperature post-annealing was not required to form the L10 FePt phase. The entire ignition and combustion process lasted no more than one minute. The L10 FePt phase could form in the presence of the high temperature caused by the exothermic combustion reaction. Adjusting the glycine-to-metal ion molar ratio from 0.5 to 6.0 allowed its effects on the phase transformation and magnetic properties of the products to be investigated. X-ray diffraction indicated that pure phase L10 FePt was obtained at a glycine-to-metal ion molar ratio of 1.5. Transmission electron microscopy indicated that the monodisperse L10 FePt nanoparticles had an average particle size of about 20 nm. The reasons why the as-synthesized L10 FePt nanoparticles were not aggregated and sintered could be attributed to the large amount, a gas is being released and the short duration of heat treatment during this combustion. This finding constituted a significant improvement in the synthesis of L10 FePt nanoparticles. Magnetic measurements showed that the L10 FePt nanoparticles had a coercivity of 15.8 kOe at 300 K, and 23.2 kOe at 5 K. Thus, the L10 FePt nanoparticles had a very large coercivity.

  8. Large difference between the magnetic properties of Ba and Ti co-doped BiFeO3 bulk materials and their corresponding nanoparticles prepared by ultrasonication

    Science.gov (United States)

    Ahmmad, Bashir; Kanomata, Kensaku; Koike, Kunihiro; Kubota, Shigeru; Kato, Hiroaki; Hirose, Fumihiko; Billah, Areef; Jalil, M. A.; Basith, M. A.

    2016-07-01

    The ceramic pellets of the nominal compositions Bi0.7Ba0.3Fe1-x Ti x O3 (x  =  0.00-0.20) were prepared initially by standard solid state reaction technique. The pellets were then ground into micrometer-sized powders and mixed with isopropanol in an ultrasonic bath to prepare nanoparticles. The x-ray diffraction patterns demonstrate the presence of a significant number of impurity phases in bulk powder materials. Interestingly, these secondary phases were completely removed due to the sonication of these bulk powder materials for 60 minutes. The field and temperature dependent magnetization measurements exhibited significant difference between the magnetic properties of the bulk materials and their corresponding nanoparticles. We anticipate that the large difference in the magnetic behavior may be associated with the presence and absence of secondary impurity phases in the bulk materials and their corresponding nanoparticles, respectively. The leakage current density of the bulk materials was also found to suppress in the ultrasonically prepared nanoparticles compared to that of bulk counterparts.

  9. The preparation and characterization of chitin and chitosan under large-scale submerged fermentation level using shrimp by-products as substrate.

    Science.gov (United States)

    Zhang, Hongcai; Yun, Sanyue; Song, Lingling; Zhang, Yiwen; Zhao, Yanyun

    2017-03-01

    The crustacean shells of crabs and shrimps produces quantities of by-products, leading to seriously environmental pollution and human health problems during industrial processing, yet they turned into high-value useful products, such as chitin and chitosan. To prepare them under large-scale submerged fermentation level, shrimp shell powders (SSPs) was fermented by successive three-step fermentation of Serratia marcescens B742, Lactobacillus plantarum ATCC 8014 and Rhizopus japonicus M193 to extract chitin and chitosan based on previously optimal conditions. Moreover, the key parameters was investigated to monitor the changes of resulted products during fermentation process. The results showed that the yield of prepared chitin and chitosan reached 21.35 and 13.11% with the recovery rate of 74.67 and 63.42%, respectively. The degree of deacetylation (DDA) and molecular mass (MM) of produced chitosan were 81.23% and 512.06kDa, respectively. The obtained chitin and chitosan was characterized using Fourier transform infrared spectrometer (FT-IR) and X-ray diffraction (XRD) analysis. The established microbial fermentation method can be applied for the industrial large-scale production of chitin and chitosan, while the use of chemical reagents was significantly reduced. Copyright © 2016 Elsevier B.V. All rights reserved.

  10. Low-Temperature Preparation of Tungsten Oxide Anode Buffer Layer via Ultrasonic Spray Pyrolysis Method for Large-Area Organic Solar Cells.

    Science.gov (United States)

    Ji, Ran; Zheng, Ding; Zhou, Chang; Cheng, Jiang; Yu, Junsheng; Li, Lu

    2017-07-18

    Tungsten oxide (WO₃) is prepared by a low-temperature ultrasonic spray pyrolysis method in air atmosphere, and it is used as an anode buffer layer (ABL) for organic solar cells (OSCs). The properties of the WO₃ transition metal oxide material as well as the mechanism of ultrasonic spray pyrolysis processes are investigated. The results show that the ultrasonic spray pyrolysized WO₃ ABL exhibits low roughness, matched energy level, and high conductivity, which results in high charge transport efficiency and suppressive recombination in OSCs. As a result, compared to the OSCs based on vacuum thermal evaporated WO₃, a higher power conversion efficiency of 3.63% is reached with low-temperature ultrasonic spray pyrolysized WO₃ ABL. Furthermore, the mostly spray-coated OSCs with large area was fabricated, which has a power conversion efficiency of ~1%. This work significantly enhances our understanding of the preparation and application of low temperature-processed WO₃, and highlights the potential of large area, all spray coated OSCs for sustainable commercial fabrication.

  11. Low-Temperature Preparation of Tungsten Oxide Anode Buffer Layer via Ultrasonic Spray Pyrolysis Method for Large-Area Organic Solar Cells

    Directory of Open Access Journals (Sweden)

    Ran Ji

    2017-07-01

    Full Text Available Tungsten oxide (WO3 is prepared by a low-temperature ultrasonic spray pyrolysis method in air atmosphere, and it is used as an anode buffer layer (ABL for organic solar cells (OSCs. The properties of the WO3 transition metal oxide material as well as the mechanism of ultrasonic spray pyrolysis processes are investigated. The results show that the ultrasonic spray pyrolysized WO3 ABL exhibits low roughness, matched energy level, and high conductivity, which results in high charge transport efficiency and suppressive recombination in OSCs. As a result, compared to the OSCs based on vacuum thermal evaporated WO3, a higher power conversion efficiency of 3.63% is reached with low-temperature ultrasonic spray pyrolysized WO3 ABL. Furthermore, the mostly spray-coated OSCs with large area was fabricated, which has a power conversion efficiency of ~1%. This work significantly enhances our understanding of the preparation and application of low temperature-processed WO3, and highlights the potential of large area, all spray coated OSCs for sustainable commercial fabrication.

  12. Textured PrCo{sub 5} nanoflakes with large coercivity prepared by low power surfactant-assisted ball milling

    Energy Technology Data Exchange (ETDEWEB)

    Zuo, Wen-Liang, E-mail: wlzuo@iphy.ac.cn; Liu, Rong-Ming; Zheng, Xin-Qi; Wu, Rong-Rong; Hu, Feng-Xia; Sun, Ji-Rong; Shen, Bao-Gen, E-mail: shenbg@aphy.iphy.ac.cn [State Key Laboratory for Magnetism, Institute of Physics, Chinese Academy of Sciences, Beijing, 100190 (China)

    2014-05-07

    The effect of the milling time on the structure, morphology, coercivity, and remanence ratio of textured PrCo{sub 5} nanoflakes produced by low power surfactant-assisted ball milling (SABM) was investigated. The X-ray powder diffraction (XRD) patterns indicate that the SABM PrCo{sub 5} samples are all CaCu{sub 5}-type hexagonal structure. The average grain size is smaller than 10 nm when the SABM time is equal to or longer than 5.5 h. The thickness of nanoflakes is mainly in the range of 50−100 nm while the length is 0.5−5 μm when the SABM time reaches 8 h. For the field-aligned PrCo{sub 5} nanoflakes, the out-of-plane texture is indicated from the increasing (0 0 l) peaks in the XRD patterns, and the easy magnetization direction is perpendicular to the flake surface. The strong texture of PrCo{sub 5} nanoflakes leads to a large coercivity H{sub c} (7.8 kOe) and obvious anisotropic magnetic behaviors for the aligned samples.

  13. Preparation of Polyclonal Antibodies of Rubisco Large and Small Subunits and Their Application in the Functional Analysis of the Genes

    Institute of Scientific and Technical Information of China (English)

    Peng-Da MA; Tian-Cheng LU; Xiao-Fu ZHOU; Xiao-Juan ZHU; Xing-Zhi WANG

    2004-01-01

    Spinach Rubisco (ribulose-l,5-bisphosphate carboxylase/oxygenase) large (rbcL) and small (rbcS) subunits were separated by SDS-PAGE, and protein amount and purity were determined by Bradford assay. Polyclonal antibodies against rbcL and rbcS subunit were generated in female BALB/c mice and had no cross-reaction with each other. A total of 81 μg antigens were used and 0.3 ml anti-sera with titer of 1:5000were yielded. The antibodies were also applicable to study rbcL and rbcS in tobacco plant Nicotiana benthamiana. Potato virus X vector pGR107 induced silencing of rbcS gene by Agrobacterium in Nicotiana benthaniana was performed. The expression level ofrbcL and rbcS was lower in rbcS silenced plants than that in control plants as detected by the corresponding antibodies. This implied that the expression of rbcL was regulated by rbcS.

  14. A propidium monoazide-quantitative PCR method for the detection and quantification of viable Enterococcus faecalis in large-volume samples of marine waters.

    Science.gov (United States)

    Salam, Khaled W; El-Fadel, Mutasem; Barbour, Elie K; Saikaly, Pascal E

    2014-10-01

    The development of rapid detection assays of cell viability is essential for monitoring the microbiological quality of water systems. Coupling propidium monoazide with quantitative PCR (PMA-qPCR) has been successfully applied in different studies for the detection and quantification of viable cells in small-volume samples (0.25-1.00 mL), but it has not been evaluated sufficiently in marine environments or in large-volume samples. In this study, we successfully integrated blue light-emitting diodes for photoactivating PMA and membrane filtration into the PMA-qPCR assay for the rapid detection and quantification of viable Enterococcus faecalis cells in 10-mL samples of marine waters. The assay was optimized in phosphate-buffered saline and seawater, reducing the qPCR signal of heat-killed E. faecalis cells by 4 log10 and 3 log10 units, respectively. Results suggest that high total dissolved solid concentration (32 g/L) in seawater can reduce PMA activity. Optimal PMA-qPCR standard curves with a 6-log dynamic range and detection limit of 10(2) cells/mL were generated for quantifying viable E. faecalis cells in marine waters. The developed assay was compared with the standard membrane filter (MF) method by quantifying viable E. faecalis cells in seawater samples exposed to solar radiation. The results of the developed PMA-qPCR assay did not match that of the standard MF method. This difference in the results reflects the different physiological states of E. faecalis cells in seawater. In conclusion, the developed assay is a rapid (∼5 h) method for the quantification of viable E. faecalis cells in marine recreational waters, which should be further improved and tested in different seawater settings.

  15. A propidium monoazide–quantitative PCR method for the detection and quantification of viable Enterococcus faecalis in large-volume samples of marine waters

    KAUST Repository

    Salam, Khaled W.

    2014-08-23

    The development of rapid detection assays of cell viability is essential for monitoring the microbiological quality of water systems. Coupling propidium monoazide with quantitative PCR (PMA-qPCR) has been successfully applied in different studies for the detection and quantification of viable cells in small-volume samples (0.25-1.00 mL), but it has not been evaluated sufficiently in marine environments or in large-volume samples. In this study, we successfully integrated blue light-emitting diodes for photoactivating PMA and membrane filtration into the PMA-qPCR assay for the rapid detection and quantification of viable Enterococcus faecalis cells in 10-mL samples of marine waters. The assay was optimized in phosphate-buffered saline and seawater, reducing the qPCR signal of heat-killed E. faecalis cells by 4 log10 and 3 log10 units, respectively. Results suggest that high total dissolved solid concentration (32 g/L) in seawater can reduce PMA activity. Optimal PMA-qPCR standard curves with a 6-log dynamic range and detection limit of 102 cells/mL were generated for quantifying viable E. faecalis cells in marine waters. The developed assay was compared with the standard membrane filter (MF) method by quantifying viable E. faecalis cells in seawater samples exposed to solar radiation. The results of the developed PMA-qPCR assay did not match that of the standard MF method. This difference in the results reflects the different physiological states of E. faecalis cells in seawater. In conclusion, the developed assay is a rapid (∼5 h) method for the quantification of viable E. faecalis cells in marine recreational waters, which should be further improved and tested in different seawater settings. © 2014 Springer-Verlag Berlin Heidelberg.

  16. Origin and emplacement of the andesite of Burroughs Mountain, a zoned, large-volume lava flow at Mount Rainier, Washington, USA

    Science.gov (United States)

    Stockstill, Karen R.; Vogel, Thomas A.; Sisson, Thomas W.

    2003-01-01

    Burroughs Mountain, situated at the northeast foot of Mount Rainier, WA, exposes a large-volume (3.4 km 3) andesitic lava flow, up to 350 m thick and extending 11 km in length. Two sampling traverses from flow base to eroded top, over vertical sections of 245 and 300 m, show that the flow consists of a felsic lower unit (100 m thick) overlain sharply by a more mafic upper unit. The mafic upper unit is chemically zoned, becoming slightly more evolved upward; the lower unit is heterogeneous and unzoned. The lower unit is also more phenocryst-rich and locally contains inclusions of quenched basaltic andesite magma that are absent from the upper unit. Widespread, vuggy, gabbronorite-to-diorite inclusions may be fragments of shallow cumulates, exhumed from the Mount Rainier magmatic system. Chemically heterogeneous block-and-ash-flow deposits that conformably underlie the lava flow were the earliest products of the eruptive episode. The felsic-mafic-felsic progression in lava composition resulted from partial evacuation of a vertically-zoned magma reservoir, in which either (1) average depth of withdrawal increased, then decreased, during eruption, perhaps due to variations in effusion rate, or (2) magmatic recharge stimulated ascent of a plume that brought less evolved magma to shallow levels at an intermediate stage of the eruption. Pre-eruptive zonation resulted from combined crystallization-differentiation and intrusion(s) of less evolved magma into the partly crystallized resident magma body. The zoned lava flow at Burroughs Mountain shows that, at times, Mount Rainier's magmatic system has developed relatively large, shallow reservoirs that, despite complex recharge events, were capable of developing a felsic-upward compositional zonation similar to that inferred from large ash-flow sheets and other zoned lava flows.

  17. A dosimetric comparison of 3D-CRT, IMRT, and static tomotherapy with an SIB for large and small breast volumes

    Energy Technology Data Exchange (ETDEWEB)

    Michalski, Andrea [Department of Health Science (MRS), The University of Sydney, Lidcombe, New South Wales (Australia); Central Coast Cancer Centre, Gosford Hospital, Gosford, New South Wales (Australia); Atyeo, John, E-mail: john.atyeo@sydney.edu.au [Department of Health Science (MRS), The University of Sydney, Lidcombe, New South Wales (Australia); Cox, Jennifer [Department of Health Science (MRS), The University of Sydney, Lidcombe, New South Wales (Australia); Department of Radiation Oncology, Royal North Shore Hospital, St Leonards, New South Wales (Australia); Rinks, Marianne [Department of Health Science (MRS), The University of Sydney, Lidcombe, New South Wales (Australia); Radiation Oncology, Cancer Services, Illawarra Shoalhaven Local Health District, Wollongong, New South Wales (Australia); Morgia, Marita; Lamoury, Gillian [Department of Radiation Oncology, Royal North Shore Hospital, St Leonards, New South Wales (Australia)

    2014-07-01

    Radiation therapy to the breast is a complex task, with many different techniques that can be employed to ensure adequate dose target coverage while minimizing doses to the organs at risk. This study compares the dose planning outcomes of 3 radiation treatment modalities, 3 dimensional conformal radiation therapy (3D-CRT), intensity-modulated radiation therapy (IMRT), and static tomotherapy, for left-sided whole-breast radiation treatment with a simultaneous integrated boost (SIB). Overall, 20 patients with left-sided breast cancer were separated into 2 cohorts, small and large, based on breast volume. Dose plans were produced for each patient using 3D-CRT, IMRT, and static tomotherapy. All patients were prescribed a dose of 45 Gy in 20 fractions to the breast with an SIB of 56 Gy in 20 fractions to the tumor bed and normalized so that D{sub 98%} > 95% of the prescription dose. Dosimetric comparisons were made between the 3 modalities and the interaction of patient size. All 3 modalities offered adequate planning target volume (PTV) coverage with D{sub 98%} > 95% and D{sub 2%} < 107%. Static tomotherapy offered significantly improved (p = 0.006) dose homogeneity to the PTV{sub boost} {sub eval} (0.079 ± 0.011) and breast minus the SIB volume (Breast{sub SIB}) (p < 0.001, 0.15 ± 0.03) compared with the PTV{sub boost} {sub eval} (0.085 ± 0.008, 0.088 ± 0.12) and Breast{sub SIB} (0.22 ± 0.05, 0.23 ± 0.03) for IMRT and 3D-CRT, respectively. Static tomotherapy also offered statistically significant reductions (p < 0.001) in doses to the ipsilateral lung mean dose of 6.79 ± 2.11 Gy compared with 7.75 ± 2.54 Gy and 8.29 ± 2.76 Gy for IMRT and 3D-CRT, respectively, and significantly (p < 0.001) reduced heart doses (mean = 2.83 ± 1.26 Gy) compared to both IMRT and 3D-CRT (mean = 3.70 ± 1.44 Gy and 3.91 ± 1.58 Gy). Static tomotherapy is the dosimetrically superior modality for the whole breast with an SIB compared with IMRT and 3D-CRT. IMRT is superior to 3D

  18. The large-area CdTe thin film for CdS/CdTe solar cell prepared by physical vapor deposition in medium pressure

    Science.gov (United States)

    Luo, Run; Liu, Bo; Yang, Xiaoyan; Bao, Zheng; Li, Bing; Zhang, Jingquan; Li, Wei; Wu, Lili; Feng, Lianghuan

    2016-01-01

    The Cadmium telluride (CdTe) thin film has been prepared by physical vapor deposition (PVD), the Ar + O2 pressure is about 0.9 kPa. This method is a newer technique to deposit CdTe thin film in large area, and the size of the film is 30 × 40 cm2. This method is much different from the close-spaced sublimation (CSS), as the relevance between the source temperature and the substrate temperature is weak, and the gas phase of CdTe is transferred to the substrate by Ar + O2 flow. Through this method, the compact and uniform CdTe film (30 × 40 cm2) has been achieved, and the performances of the CdTe thin film have been determined by transmission spectrum, SEM and XRD. The film is observed to be compact with a good crystallinity, the CdTe is polycrystalline with a cubic structure and a strongly preferred (1 1 1) orientation. Using the CdTe thin film (3 × 5 cm2) which is taken from the deposited large-area film, the 14.6% efficiency CdS/CdTe thin film solar cell has been prepared successfully. The structure of the cell is glass/FTO/CdS/CdTe/graphite slurry/Au, short circuit current density (Jsc) of the cell is 26.9 mA/cm2, open circuit voltage (Voc) is 823 mV, and filling factor (FF) is 66.05%. This technique can be a quite promising method to apply in the industrial production, as it has great prospects in the fabricating of large-area CdTe film.

  19. Improving the Sensitivity, Resolution, and Peak Capacity of Gradient Elution in Capillary Liquid Chromatography with Large-Volume Injections by Using Temperature-Assisted On-Column Solute Focusing.

    Science.gov (United States)

    Wilson, Rachael E; Groskreutz, Stephen R; Weber, Stephen G

    2016-05-17

    Capillary HPLC (cLC) with gradient elution is the separation method of choice for the fields of proteomics and metabolomics. This is due to the complementary nature of cLC flow rates and electrospray or nanospray ionization mass spectrometry (ESI-MS). The small column diameters result in good mass sensitivity. Good concentration sensitivity is also possible by injection of relatively large volumes of solution and relying on solvent-based solute focusing. However, if the injection volume is too large or solutes are poorly retained during injection, volume overload occurs which leads to altered peak shapes, decreased sensitivity, and lower peak capacity. Solutes that elute early even with the use of a solvent gradient are especially vulnerable to this problem. In this paper, we describe a simple, automated instrumental method, temperature-assisted on-column solute focusing (TASF), that is capable of focusing large volume injections of small molecules and peptides under gradient conditions. By injecting a large sample volume while cooling a short segment of the column inlet at subambient temperatures, solutes are concentrated into narrow bands at the head of the column. Rapidly raising the temperature of this segment of the column leads to separations with less peak broadening in comparison to solvent focusing alone. For large volume injections of both mixtures of small molecules and a bovine serum albumin tryptic digest, TASF improved the peak shape and resolution in chromatograms. TASF showed the most dramatic improvements with shallow gradients, which is particularly useful for biological applications. Results demonstrate the ability of TASF with gradient elution to improve the sensitivity, resolution, and peak capacity of volume overloaded samples beyond gradient compression alone. Additionally, we have developed and validated a double extrapolation method for predicting retention factors at extremes of temperature and mobile phase composition. Using this method

  20. Large Polycrystalline Silicon Grains Prepared by Excimer Laser Crystallization of Sputtered Amorphous Silicon Film with Process Temperature at 100 °C

    Science.gov (United States)

    He, Ming; Ishihara, Ryoichi; Neihof, Ellen J. J.; van Andel, Yvonne; Schellevis, Hugo; Metselaar, Wim; Beenakker, Kees

    2007-03-01

    Large polycrystalline silicon (poly-Si) grains with a diameter of 1.8 μm are successfully prepared by excimer laser crystallization (ELC) of a sputtered amorphous silicon (α-Si) film at a maximum process temperature of 100 °C. By pulsed DC magnetron sputtering, α-Si is deposited on a non-structured oxidized wafer. It is found that the α-Si film deposited with a bias is easily ablated during ELC, even at an energy density below the super lateral growth (SLG) region. However, the α-Si film deposited without a bias can endure an energy density well beyond the SLG region without ablation. This zero-bias sputtered α-Si film with a high compressive stress has a low Ar content and a high density, which is beneficial for the suppression of ablation. Large grains with a petal-like shape can be obtained in a wide energy density window, which can be a result from some fine crystallites in the α-Si matrix. These large grains with a low process temperature are promising for the direct formation of system circuits as well as a high-quality display on a plastic foil.

  1. Analysis of iodinated haloacetic acids in drinking water by reversed-phase liquid chromatography/electrospray ionization/tandem mass spectrometry with large volume direct aqueous injection.

    Science.gov (United States)

    Li, Yongtao; Whitaker, Joshua S; McCarty, Christina L

    2012-07-01

    A large volume direct aqueous injection method was developed for the analysis of iodinated haloacetic acids in drinking water by using reversed-phase liquid chromatography/electrospray ionization/tandem mass spectrometry in the negative ion mode. Both the external and internal standard calibration methods were studied for the analysis of monoiodoacetic acid, chloroiodoacetic acid, bromoiodoacetic acid, and diiodoacetic acid in drinking water. The use of a divert valve technique for the mobile phase solvent delay, along with isotopically labeled analogs used as internal standards, effectively reduced and compensated for the ionization suppression typically caused by coexisting common inorganic anions. Under the optimized method conditions, the mean absolute and relative recoveries resulting from the replicate fortified deionized water and chlorinated drinking water analyses were 83-107% with a relative standard deviation of 0.7-11.7% and 84-111% with a relative standard deviation of 0.8-12.1%, respectively. The method detection limits resulting from the external and internal standard calibrations, based on seven fortified deionized water replicates, were 0.7-2.3 ng/L and 0.5-1.9 ng/L, respectively.

  2. Rapid and sensitive solid phase extraction-large volume injection-gas chromatography for the analysis of mineral oil saturated and aromatic hydrocarbons in cardboard and dried foods.

    Science.gov (United States)

    Moret, Sabrina; Barp, Laura; Purcaro, Giorgia; Conte, Lanfranco S

    2012-06-22

    A rapid off-line solid phase extraction-large volume injection-gas chromatography-flame ionisation detection (SPE-LVI-GC-FID) method, based on the use of silver silica gel and low solvent consumption, was developed for mineral oil saturated hydrocarbon (MOSH) and mineral oil aromatic hydrocarbon (MOAH) determination in cardboard and dried foods packaged in cardboard. The SPE method was validated using LVI with a conventional on-column injector and the retention gap technique (which allowed to inject up to 50 μL of the sample). Detector response was linear over all the concentration range tested (0.5-250 μg/mL), recoveries were practically quantitative, repeatability was good (coefficients of variation lower than 7%) and limit of quantification adequate to quantify the envisioned limit of 0.15 mg/kg proposed in Germany for MOAH analysis in food samples packaged in recycled cardboard. Rapid heating of the GC oven allowed to increase sample throughput (3-4 samples per hour) and to enhance sensitivity. The proposed method was used for MOSH and MOAH determination in selected food samples usually commercialised in cardboard packaging. The most contaminated was a tea sample (102.2 and 7.9 mg/kg of MOSH and MOAH below n-C25, respectively), followed by a rice and a sugar powder sample, all packaged in recycled cardboard.

  3. Turbidite record of frequency and source of large volume (>100 km3) Canary Island landslides in the last 1.5 Ma: Implications for landslide triggers and geohazards

    Science.gov (United States)

    Hunt, J. E.; Wynn, R. B.; Talling, P. J.; Masson, D. G.

    2013-07-01

    During the last two decades, numerous studies have focused on resolving the landslide histories of the Canary Islands. Issues surrounding the preservation and dating of onshore and proximal submarine landslide deposits precludes accurate determination of event ages. However, submarine landslides often disaggregate and generate sediment gravity flows. Volcaniclastic turbidites sampled from Madeira Abyssal Plain piston cores represent a record of eight large-volume failures from the Western Canary Islands in the last 1.5 Ma. During this time, there is a mean recurrence rate of 200 ka, while the islands of El Hierro and Tenerife have individual landslide recurrences of 500 ka and 330 ka, respectively. Deposits from the 15 ka El Golfo landslide from El Hierro and 165 ka Icod landslide from Tenerife are examined. This study also identifies potential deposits associated with the Orotava (535 ka), Güímar (850 ka), and Rogues de García landslides (1.2 Ma) from Tenerife, El Julan (540 ka), and El Tiñor (1.05 Ma) landslides from El Hierro, and the Cumbre Nueva landslide (485 ka) from La Palma. Seven of eight landslides occurred during major deglaciations or subsequent interglacial periods, which represent 55% of the time. However, all of the studied landslides occur during or at the end of periods of protracted island volcanism, which generally represent 60% of the island histories. Although climate may precondition failures, it is suggested that volcanism presents a more viable preconditioning and trigger mechanism for Canary Island landslides.

  4. Analysis of Six β-Lactam Residues in Milk and Egg by Micellar Electrokinetic Chromatography with Large-Volume Sample Stacking and Polarity Switching.

    Science.gov (United States)

    Shao, Yu-Xiu; Chen, Guan-Hua; Fang, Rou; Zhang, Li; Yi, Ling-Xiao; Meng, Hong-Lian

    2016-05-04

    A new micellar electrokinetic chromatography method with large-volume sample stacking and polarity switching was developed to analyze amoxicllin, cephalexin, oxacillin, penicillin G, cefazolin, and cefoperazone in milk and egg. The important parameters influencing separation and enrichment factors were optimized. The optimized running buffer consisted of 10 mM phosphate and 22 mM SDS at pH 6.7. The sample size was 1.47 kPa × 690 s, the reverse voltage was 20 kV, and the electric current recovery was 95%. Under these optimum conditions, the enrichment factors of six β-lactams were 193-601. Their LODs were <0.26 ng/g, and LOQs were all 2 ng/g, which was only 1/50-1/2 of the maximum residual limits demanded by U.S. and Japanese regulations. The intraday and interday RSDs of method were lower than 3.70 and 3.91%, respectively. The method can be applied to determine these six antibiotic residues in egg and milk.

  5. High total metabolic tumor volume in PET/CT predicts worse prognosis in diffuse large B cell lymphoma patients with bone marrow involvement in rituximab era.

    Science.gov (United States)

    Song, Moo-Kon; Yang, Deok-Hwan; Lee, Gyeong-Won; Lim, Sung-Nam; Shin, Seunghyeon; Pak, Kyoung June; Kwon, Seong Young; Shim, Hye Kyung; Choi, Bong-Hoi; Kim, In-Suk; Shin, Dong-Hoon; Kim, Seong-Geun; Oh, So-Yeon

    2016-03-01

    Bone marrow involvement (BMI) in diffuse large B cell lymphoma (DLBCL) was naively regarded as an adverse clinical factor. However, it has been unknown which factor would separate clinical outcomes in DLBCL patients with BMI. Recently, metabolic tumor volume (MTV) on positron emission tomography/computed tomography (PET/CT) was suggested to predict prognosis in several lymphoma types. Therefore, we investigated whether MTV would separate the outcomes in DLBCL patients with BMI. MTV on PET/CT was defined as an initial tumor burden as target lesion ≥ standard uptake value, 2.5 in 107 patients with BMI. Intramedullary (IM) MTV was defined as extent of BMI and total MTV was as whole tumor burden. 260.5 cm(3) and 601.2 cm(3) were ideal cut-off values for dividing high and low MTV status in the IM and total lymphoma lesions in Receiver Operating Curve analysis. High risk NCCN-IPI (phigh IM MTV status (phigh total MTV status (phigh risk NCCN-IPI (PFS, p=0.006; OS, p=0.013), concordant subtype (PFS, p=0.005; OS, p=0.007), and high total MTV status (PFS, p<0.001; OS, p<0.001) had independent clinical impacts. MTV had prognostic significances for survivals in DLBCL with BMI.

  6. 大体积承台混凝土配合比设计及工程应用%Design and Construction Application of Large Volume Cap Concrete

    Institute of Scientific and Technical Information of China (English)

    孙宏图

    2016-01-01

    针对东明黄河公路大桥主桥主墩承台混凝土的特点,通过掺加大掺量复合矿物掺合料、细集料采用机制砂及掺加聚羧酸缓凝高效减水剂的方案,配制出密实性好、水化热低、抗裂性能好的大体积混凝土。同时,结合科学的施工措施,有效防止了大体积承台温度裂缝的产生。%Aimed at the characteristics of the main pier pile concrete of the main bridge of Dongming Yellow River Highway Bridge, the mass concrete with good compactness, low hydration heat, good crack resistance is made by the plan of mixing lots of composite mineral admixture, using machine-made sand as fine aggregate and adding polycarboxylic acid retarded high efficiency water reducing agent. At the same time, the large volume cap temperature cracks are effectively prevented by the scientific construction measures.

  7. The application of large volume airgun sources to the onshore-offshore seismic surveys: implication of the experimental results in northern South China Sea

    Institute of Scientific and Technical Information of China (English)

    QIU XueLin; CHEN Yong; ZHU RiXiang; XU HuiLong; SHI XiaoBin; YE ChunMing; ZHAO MingHui; XIA ShaoHong

    2007-01-01

    Onshore-offshore seismic experiments were carried out for the first time in northern South China Sea using large volume airgun sources at sea and seismic stations on land. The experimental results indicate that seismic signals from the new airgun array of R/V Shiyan 2 can be detected as far as 255 km. The signal effective area reaches nearly 50000 km2, which covers Hong Kong and Pearl River Delta. Compared with the old airgun array, the signal amplitude, propagation distance and effective area of the new airgun array have been increased notably, which demonstrates that the upgrade of the airgun source was successful. Comparisons with previous experimental results in other regions show that the shooting effect of the new airgun array is similar to those best airgun sources in the world. Especially, it is a new breakthrough in using the permanent seismic stations onshore to record long distance airgun signals offshore, which has great significance to the realization of the "seismic radar" concept and the 3D seismic surveys of crustal structure in coastal areas.

  8. Characterization of Large Volume 3.5″ x 8″ LaBr3:Ce Detectors for the HECTOR+ array

    Directory of Open Access Journals (Sweden)

    Camera F.

    2014-03-01

    Full Text Available A selection of the properties of large volume, cylindrical 3.5” x 8” LaBr3:Ce scintillation detectors coupled to a 3.5” PMT (model R10233-1000SEL from HAMAMATSU and a special designed Voltage Divider (LABRVD will be discussed. A number of 10 of such detectors constitute the HECTOR+ array which, in fall 2012, measured at GSI coupled to the AGATA DEMOSTRATOR at the PRESPEC experimental setup. These crystals are among the largest ever produced and needed to be characterized. We have performed several tests and here we discuss, in particular, the energy resolution measured using monochromatic γ−ray sources and in-beam reactions producing γ−rays up to 22.6 MeV. As already measured in two previous works a saturation in the energy resolution was observed in case of high energy gamma rays. Crystal non-homogeneities and PMT gain drifts can affect the resolution of measurements especially in case of high energy γ−rays.

  9. Characterization of Large Volume 3.5″ x 8″ LaBr3:Ce Detectors for the HECTOR+ array

    Science.gov (United States)

    Camera, F.; Giaz, A.; Pellegri, L.; Riboldi, S.; Blasi, N.; Boiano, C.; Bracco, A.; Brambilla, S.; Ceruti, S.; Coelli, S.; Crespi, F. C. L.; Csatlòs, M.; Krasznahorkay, A.; Gulyàs, J.; Lodetti, S.; Frega, S.; Miani, A.; Million, B.; Stuhl, L.; Wieland, O.

    2014-03-01

    A selection of the properties of large volume, cylindrical 3.5" x 8" LaBr3:Ce scintillation detectors coupled to a 3.5" PMT (model R10233-1000SEL from HAMAMATSU) and a special designed Voltage Divider (LABRVD) will be discussed. A number of 10 of such detectors constitute the HECTOR+ array which, in fall 2012, measured at GSI coupled to the AGATA DEMOSTRATOR at the PRESPEC experimental setup. These crystals are among the largest ever produced and needed to be characterized. We have performed several tests and here we discuss, in particular, the energy resolution measured using monochromatic γ-ray sources and in-beam reactions producing γ-rays up to 22.6 MeV. As already measured in two previous works a saturation in the energy resolution was observed in case of high energy gamma rays. Crystal non-homogeneities and PMT gain drifts can affect the resolution of measurements especially in case of high energy γ-rays.

  10. Dispersive liquid-liquid microextraction for the determination of nitrophenols in soils by microvial insert large volume injection-gas chromatography-mass spectrometry.

    Science.gov (United States)

    Cacho, J I; Campillo, N; Viñas, P; Hernández-Córdoba, M

    2016-07-22

    A rapid and sensitive procedure for the determination of six NPs in soils by gas chromatography and mass spectrometry (GC-MS) is proposed. Ultrasound assisted extraction (UAE) is used for NP extraction from soil matrices to an organic solvent, while the environmentally friendly technique dispersive liquid-liquid microextraction (DLLME) is used for the preconcentration of the resulting UAE extracts. NPs were derivatized by applying an "in-situ" acetylation procedure, before being injected into the GC-MS system using microvial insert large volume injection (LVI). Several parameters affecting UAE, DLLME, derivatization and injection steps were investigated. The optimized procedure provided recoveries of 86-111% from spiked samples. Precision values of the procedure (expressed as relative standard deviation, RSD) lower than 12%, and limits of quantification ranging from 1.3 to 2.6ngg(-1), depending on the compound, were obtained. Twenty soil samples, obtained from military, industrial and agricultural areas, were analyzed by the proposed method. Two of the analytes were quantified in two of the samples obtained from industrial areas, at concentrations in the 4.8-9.6ngg(-1) range.

  11. Towards Large Volume Big Divisor D3-D7 "mu-Split Supersymmetry" and Ricci-Flat Swiss-Cheese Metrics, and Dimension-Six Neutrino Mass Operators

    CERN Document Server

    Dhuria, Mansi

    2012-01-01

    We show that it is possible to realize a "mu-split SUSY" scenario [1] in the context of large volume limit of type IIB compactifications on Swiss-Cheese Calabi-Yau's in the presence of a mobile space-time filling D3-brane and a (stack of) D7-brane(s) wrapping the "big" divisor Sigma_B. For this, we investigate the possibility of getting one Higgs to be light while other to be heavy in addition to a heavy Higgsino mass parameter. Further, we examine the existence of long lived gluino that manifests one of the major consequences of mu-split SUSY scenario, by computing its decay width as well as lifetime corresponding to the 3-body decays of the gluino into a quark, a squark and a neutralino or Goldstino, as well as 2-body decays of the gluino into either a neutralino or a Goldstino and a gluon. Guided by the geometric Kaehler potential for Sigma_B obtained in [2] based on GLSM techniques, and the Donaldson's algorithm [3] for obtaining numerically a Ricci-flat metric, we give details of our calculation in [4] p...

  12. Large volume sample stacking with EOF and sweeping in CE for determination of common preservatives in cosmetic products by chemometric experimental design.

    Science.gov (United States)

    Cheng, Yi-Cian; Wang, Chun-Chi; Chen, Yen-Ling; Wu, Shou-Mei

    2012-05-01

    This study proposes a capillary electrophoresis method incorporating large volume sample stacking, EOF and sweeping for detection of common preservatives used in cosmetic products. The method was developed using chemometric experimental design (fractional factorial design and central composite design) to determine multiple separation variables by efficient steps. The samples were loaded by hydrodynamic injection (10 psi, 90 s), and separated by phosphate buffer (50 mM, pH 3) containing 30% methanol and 80 mM SDS at -20 kV. During method validation, calibration curves were found to be linear over a range of 5-100 μg/mL for butyl paraben and isobutyl paraben; 0.05-10 μg/mL for ethyl paraben; 0.2-50 μg/mL for dehydroacetic acid; 0.5-70 μg/mL for methyl paraben; 5-350 μg/mL for sorbic acid; 0.02-450 μg/mL for p-hydroxybenzoic acid and 0.05-10 μg/mL for salicylic acid and benzoic acid. The analytes were analysed simultaneously and their detection limits (S/N = 3) were down to 0.005-2 μg/mL. The analysis method was successfully used for detection of preservatives used in commercial cosmetics.

  13. Large-area flexible monolithic ITO/WO3/Nb2O5/NiVOχ/ITO electrochromic devices prepared by using magnetron sputter deposition

    Science.gov (United States)

    Tang, Chien-Jen; Ye, Jia-Ming; Yang, Yueh-Ting; He, Ju-Liang

    2016-05-01

    Electrochromic devices (ECDs) have been applied in smart windows to control the transmission of sunlight in green buildings, saving up to 40-50% electricity consumption and ultimately reducing carbon dioxide emissions. However, the high manufacturing costs and difficulty of transportation of conventional massive large area ECDs has limited widespread applications. A unique design replacing the glass substrate commonly used in the ECD windows with inexpensive, light-weight and flexible polymeric substrate materials would accelerate EC adoption allowing them to be supplemented for regular windows without altering window construction. In this study, an ITO/WO3/Nb2O5/NiVOχ/ITO all-solid-state monolithic ECD with an effective area of 24 cm × 18 cm is successfully integrated on a PET substrate by using magnetron sputter deposition. The electrochromic performance and bending durability of the resultant material are also investigated. The experimental results indicate that the ultimate response times for the prepared ECD is 6 s for coloring at an applied voltage of -3 V and 5 s for bleaching at an applied voltage of +3 V, respectively. The optical transmittances for the bleached and colored state at a wavelength of 633 nm are 53% and 11%, respectively. The prepared ECD can sustain over 8000 repeated coloring and bleaching cycles, as well as tolerate a bending radius of curvature of 7.5 cm.

  14. Quantitative method of viral pollution determination for large volume of water using ferric hydroxide gel impregnated on the surface of glassfibre cartridge

    Directory of Open Access Journals (Sweden)

    Akira Homma

    1974-01-01

    Full Text Available Quantitative method of viral pollution determination for large volume of water using ferric hydroxide gel impregnated on the surface of glassfibre cartridge filter. The use of ferric hydroxide gel, impregnated on the surface of glassfibre cartridge filter enable us to recover 62.5% of virus (Poliomylitis type I, Lsc strain exsogeneously added to 400 liters of tap-water. The virus concentrator system consists of four cartridge filters, in which the three first one are clarifiers, where the contaminants are removed physically, without significant virus loss at this stage. The last cartridge filter is impregnated with ferric hydroxide gel, where the virus is adsorbed. After the required volume of water has been processed, the last filter is removed from the system and the viruses are recovered from the gel, using 1 liter of glycine/NaOH buffer, at pH 11. Immediately the eluate is clarified through series of cellulose acetate membranes mounted in a 142mm Millipore filter. For the second step of virus concentration, HC1 1N is added slowly to the eluate to achieve pH 3.5-4. MgC1, is added to give a final concentration of 0.05M and the viruses are readsorbed on a 0.45 , porosity (HA cellulose acetate membrane, mounted in a 90 mm Millipore filter. The viruses are recovered using the same eluent plus 10% of fetal calf serum, to a final volume of 3 ml. In this way, it was possible to concentrate virus from 400 liters of tap-water, into 1 liter in the first stage of virus concentration and just to 3 ml of final volume in a second step. The efficiency, simplicity and low operational cost, provded by the method, make it feasible to study viral pollution of recreational and tap-water sources.Relata-se o emprego de um concentrador portátil, o qual se mostrou capaz de recuperar 62,5% dos vírus (Polio I, amostra Lsc experimentalmente dispersos em 400 litros de água, os quais foram reduzidos a 3 ml. O sistema concentrador de vírus é composto de quatro

  15. Preparation of born-doped a-SiC:H thin films by ICP-CVD method and to the application of large-area heterojunction solar cells.

    Science.gov (United States)

    Jeong, Chaehwan; Kim, Young-Back; Lee, Suk-Ho; Kim, Jin Hyeok

    2010-05-01

    Hydrogenated amorphous silicon carbide (a-SiC:H) film has been widely used as an emitter p layer in solar cells. For the better p layer, wide optical bandgap, and high electrical conductivity should be obtained from the effective method. We prepared the boron-doped a-SiC:H thin films using inductively coupled plasma chemical vapor deposition (ICP-CVD) method and characteristics on the small-area (2 cm x 2 cm) as well as the large-area films (diameter of 100 mm) were shown on it. As a substrate, the n-type (100) oriented CZ c-Si (5.5 approximately 6.5 omega x cm, 650 microm) wafers were used and cleaned by using the reduced RCA method. A silane (SiH4) of 99.999% purity, H2 and 60% hydrogen diluted ethylene (C2H4) was used as source gas for the deposition of intrinsic a-SiC:H films, and then diborane (B2H6), as the doping gas, is added to C2H4 and SiH4/H2 during the deposition of films. The uniformity of thickness and optical bandgap from large-area as-dep. films was at 1.8% and 0.3%, respectively. Heterojunction solar cell with 2 wt%-AZO/p-a-SiC:H/i-a-Si:H/c-Si/Ag structure was fabricated and characterized with diameter of 152.3 mm in this large-area ICP-CVD system. Conversion efficiency of 9.123% was achieved with a practical area of 100 mm x 100 mm, which can show the potentials to the fabrication of the large-area solar cell using ICP-CVD method.

  16. The prognostic value of baseline {sup 18}F-FDG PET/CT in steroid-naive large-vessel vasculitis: introduction of volume-based parameters

    Energy Technology Data Exchange (ETDEWEB)

    Dellavedova, L. [Ospedale Civile di Legnano, PET/CT Center - Nuclear Medicine Department, Legnano (Italy); University of Milan, Department of Health Sciences, Milan (Italy); Carletto, M.; Maffioli, L.S. [Ospedale Civile di Legnano, PET/CT Center - Nuclear Medicine Department, Legnano (Italy); Faggioli, P.; Sciascera, A.; Mazzone, A. [Ospedale Civile di Legnano, Internal Medicine Department, Legnano (Italy); Del Sole, A. [University of Milan, Department of Health Sciences, Milan (Italy)

    2016-02-15

    The aim of this study was to analyse if the result of a baseline {sup 18}F-fluorodeoxyglucose (FDG) positron emission tomography (PET)/CT scan, in large-vessel vasculitis (LVV) patients, is able to predict the course of the disease, not only in terms of presence/absence of final complications but also in terms of favourable/complicated progress (response to steroid therapy, time to steroid suspension, relapses, etc.). A total of 46 consecutive patients, who underwent {sup 18}F-FDG PET/CT between May 2010 and March 2013 for fever of unknown origin (FUO) or suspected vasculitis (before starting corticosteroid therapy), were enrolled. The diagnosis of LVV was confirmed in 17 patients. Considering follow-up results, positive LVV patients were divided into two groups, one characterized by favourable (nine) and the other by complicated progress (eight), on the basis of presence/absence of vascular complications, presence/absence of at least another positive PET/CT during follow-up and impossibility to comply with the tapering schedule of the steroid due to biochemical/symptomatic relapse. Vessel uptake in subjects of the two groups was compared in terms of intensity and extension. To evaluate the extent of active disease, we introduced two volume-based parameters: ''volume of increased uptake'' (VIU) and ''total lesion glycolysis'' (TLG). The threshold used to calculate VIU on vessel walls was obtained by the ''vessel to liver'' ratio by means of receiver-operating characteristic analysis and was set at 0.92 x liver maximum standardized uptake value in each patient. Measures of tracer uptake intensity were significantly higher in patients with complicated progress compared to those with a favourable one (p < 0.05). Measures of disease extension were even more significant and TLG emerged as the best parameter to separate the two groups of patients (p = 0.01). This pilot study shows that, in LVV patients, the

  17. Preparation of a recombinant adeno-associated viral vector with a mutation of human factor IX in large scale and its expression in vitro and in vivo

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A series of adeno-associated viral vectors conraining a mutation of human factor IX (hFIXR338A) with different regulation elements were constructed and used to transduce cell lines. The plasmids and the stable transduction cell clones with high expression level of hFIXR338Awere obtained by selecting and optimizing, and then, the recombinant adeno-associated viral vector with hFIXR338Awas prepared via novel rHSV/AAV hybrid virus packaging system on a large scale, which contained the capsid protein genes. A method for producing rAAV-hFIXR338A viral stocks on a large scale and higher fiter was established,which can be used for industrial purpose. The titer of rAAV-hFIXR338A was more than 1.25x1012 particle/mL, and then, a mammalian cell line, C2C12 and the factor IXknock-out mice were transfected with the rAAV-hFIXR338Ain vitro and in vivo. The results show that the high-level expression of rAAV-hFIXR338A was achieved in cell line and hemophilia B mice. It reached at (2551.32±92.14) ng@ (106cells)-1 @ (24 h)-1 in C2C12 cell in vitro and had a peak concentration of 463.28 ng/mL in mice treated with rAAV-hFIX R338A, which was as high as the expression of rAAV-hFIX -wt (2565.76±64.36) ng@ (106 cells)-1@ (24 h)-1 in C2C12 and 453.92 ng/mL in the mice treated with rAAV-hFIX-wt) in vitro and in vivo, there is no any difference between two groups, but the clotting activity of hFIXR338A is about 2.46times higher than that of hFIX-wt. It was first reported that a mutation of human factor IX was used into gene therapy research for hemophilia B, meanwhile, a novel packaging system, rAAV/HSV was used for preparation of rAAV-hFIX R338A on a large scale, which laid the foundation of industrial production for applying rAAV viral stocks to gene therapy clinical trial for hemophilia B mediated with rAAV-hFIX.``

  18. Dispersive liquid-liquid microextraction for the determination of phenols by acetonitrile stacking coupled with sweeping-micellar electrokinetic chromatography with large-volume injection.

    Science.gov (United States)

    He, Hui; Liu, Shuhui; Meng, Zhaofu; Hu, Shibing

    2014-09-26

    The current routes to couple dispersive liquid-liquid microextraction (DLLME) with capillary electrophoresis (CE) are evaporation of water immiscible extractants and backextraction of analytes. The former is not applicable to extractants with high boiling points, the latter being effective only for acidic or basic analytes, both of which limit the further application of DLLME-CE. In this study, with 1-octanol as a model DLLME extractant and six phenols as model analytes, a novel method based on acetonitrile stacking and sweeping is proposed to accomplish large-volume injection of 1-octanol diluted with a solvent-saline mixture before micellar electrokinetic chromatography. Brij-35 and β-cyclodextrin were employed as pseudostationary phases for sweeping and also for improving the compatibility of sample zone and aqueous running buffer. A short solvent-saline plug was used to offset the adverse effect of the water immiscible extractant on focusing efficiency. The key parameters affecting separation and concentration were systematically optimized; the effect of Brij-35 and 1-octanol on focusing mechanism was discussed. Under the optimized conditions, with ∼ 30-fold concentration enrichment by DLLME, the diluted extractant (8×) was then injected into the capillary with a length of 21 cm (42% of the total length), which yielded the overall improvements in sensitivity of 170-460. Limits of detection and qualification ranged from 0.2 to 1.0 ng/mL and 1.0 to 3.4 g/mL, respectively. Acceptable repeatability lower than 3.0% for migration time and 9.0% for peak areas were obtained. The developed method was successfully applied for analysis of the phenol pollutants in real water samples.

  19. A new method to address unmet needs for extracting individual cell migration features from a large number of cells embedded in 3D volumes.

    Directory of Open Access Journals (Sweden)

    Ivan Adanja

    Full Text Available BACKGROUND: In vitro cell observation has been widely used by biologists and pharmacologists for screening molecule-induced effects on cancer cells. Computer-assisted time-lapse microscopy enables automated live cell imaging in vitro, enabling cell behavior characterization through image analysis, in particular regarding cell migration. In this context, 3D cell assays in transparent matrix gels have been developed to provide more realistic in vitro 3D environments for monitoring cell migration (fundamentally different from cell motility behavior observed in 2D, which is related to the spread of cancer and metastases. METHODOLOGY/PRINCIPAL FINDINGS: In this paper we propose an improved automated tracking method that is designed to robustly and individually follow a large number of unlabeled cells observed under phase-contrast microscopy in 3D gels. The method automatically detects and tracks individual cells across a sequence of acquired volumes, using a template matching filtering method that in turn allows for robust detection and mean-shift tracking. The robustness of the method results from detecting and managing the cases where two cell (mean-shift trackers converge to the same point. The resulting trajectories quantify cell migration through statistical analysis of 3D trajectory descriptors. We manually validated the method and observed efficient cell detection and a low tracking error rate (6%. We also applied the method in a real biological experiment where the pro-migratory effects of hyaluronic acid (HA were analyzed on brain cancer cells. Using collagen gels with increased HA proportions, we were able to evidence a dose-response effect on cell migration abilities. CONCLUSIONS/SIGNIFICANCE: The developed method enables biomedical researchers to automatically and robustly quantify the pro- or anti-migratory effects of different experimental conditions on unlabeled cell cultures in a 3D environment.

  20. Direct large volume injection ultra-high performance liquid chromatography-tandem mass spectrometry determination of artificial sweeteners sucralose and acesulfame in well water.

    Science.gov (United States)

    Wu, Minghuo; Qian, Yichao; Boyd, Jessica M; Hrudey, Steve E; Le, X Chris; Li, Xing-Fang

    2014-09-12

    Acesulfame (ACE) and sucralose (SUC) have become recognized as ideal domestic wastewater contamination indicators. Liquid chromatography-electrospray ionization mass spectrometry (LC-ESI-MS) analysis is commonly used; however, the sensitivity of SUC is more than two orders of magnitude lower than that of ACE, limiting the routine monitoring of SUC. To address this issue, we examined the ESI behavior of both ACE and SUC under various conditions. ACE is ionic in aqueous solution and efficiently produces simple [M-H](-) ions, but SUC produces multiple adduct ions, limiting its sensitivity. The formic acid (FA) adducts of SUC [M+HCOO](-) are sensitively and reproducibly generated under the LC-MS conditions. When [M+HCOO](-) is used as the precursor ion for SUC detection, the sensitivity increases approximately 20-fold compared to when [M-H](-) is the precursor ion. To further improve the limit of detection (LOD), we integrated the large volume injection approach (500μL injection) with ultra-high performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS), which reduced the method detection limit (MDL) to 0.2ng/L for ACE and 5ng/L for SUC. To demonstrate the applicability of this method, we analyzed 100 well water samples collected in Alberta. ACE was detected in 24 wells at concentrations of 1-1534ng/L and SUC in 8 wells at concentrations of 65-541ng/L. These results suggest that wastewater is the most likely source of ACE and SUC impacts in these wells, suggesting the need for monitoring the quality of domestic well water.

  1. Use of Raman Spectroscopy and Delta Volume Growth from Void Collapse to Assess Overwrap Stress Gradients Compromising the Reliability of Large Kevlar/Epoxy COPVs

    Science.gov (United States)

    Kezirian, Michael T.; Phoenix, S. Leigh; Eldridge, Jeffrey I.

    2009-01-01

    Composite Overwrapped Pressure Vessels (COPVs) are frequently used for storing pressurized gases aboard spacecraft and aircraft when weight saving is desirable compared to all-metal versions. Failure mechanisms in fibrous COPVs and variability in lifetime can be very different from their metallic counterparts; in the former, catastrophic stress-rupture can occur with virtually no warning, whereas in latter, a leak before burst design philosophy can be implemented. Qualification and certification typically requires only one burst test on a production sample (possibly after several pressure cycles) and the vessel need only meet a design burst strength (the maximum operating pressure divided by a knockdown factor). Typically there is no requirement to assess variability in burst strength or lifetime, much less determine production and materials processing parameters important to control of such variability. Characterizing such variability and its source is crucial to models for calculating required reliability over a given lifetime (e.g. R = 0.9999 for 15 years). In this paper we present a case study of how lack of control of certain process parameters in COPV manufacturing can result in variations among vessels and between production runs that can greatly increase uncertainty and reduce reliability. The vessels considered are 40-inch ( NASA Glenn Research center, Cleveland, OH, 44135 29,500 in3 ) spherical COPVs with a 0.74 in. thick Kevlar49/epoxy overwrap and with a titanium liner of which 34 were originally produced. Two burst tests were eventually performed that unexpectedly differed by almost 5%, and were 10% lower than anticipated from burst tests on 26-inch sister vessels similar in every detail. A major observation from measurements made during proof testing (autofrettage) of the 40-inch vessels was that permanent volume growth from liner yielding varied by a factor of more than two (150 in3 to 360 in3 ), which suggests large differences in the residual

  2. Sample Preparation and Extraction in Small Sample Volumes Suitable for Pediatric Clinical Studies: Challenges, Advances, and Experiences of a Bioanalytical HPLC-MS/MS Method Validation Using Enalapril and Enalaprilat

    Directory of Open Access Journals (Sweden)

    Bjoern B. Burckhardt

    2015-01-01

    Full Text Available In USA and Europe, medicines agencies force the development of child-appropriate medications and intend to increase the availability of information on the pediatric use. This asks for bioanalytical methods which are able to deal with small sample volumes as the trial-related blood lost is very restricted in children. Broadly used HPLC-MS/MS, being able to cope with small volumes, is susceptible to matrix effects. The latter restrains the precise drug quantification through, for example, causing signal suppression. Sophisticated sample preparation and purification utilizing solid-phase extraction was applied to reduce and control matrix effects. A scale-up from vacuum manifold to positive pressure manifold was conducted to meet the demands of high-throughput within a clinical setting. Faced challenges, advances, and experiences in solid-phase extraction are exemplarily presented on the basis of the bioanalytical method development and validation of low-volume samples (50 μL serum. Enalapril, enalaprilat, and benazepril served as sample drugs. The applied sample preparation and extraction successfully reduced the absolute and relative matrix effect to comply with international guidelines. Recoveries ranged from 77 to 104% for enalapril and from 93 to 118% for enalaprilat. The bioanalytical method comprising sample extraction by solid-phase extraction was fully validated according to FDA and EMA bioanalytical guidelines and was used in a Phase I study in 24 volunteers.

  3. International Conference on Harmonisation; Guidance on Q4B Evaluation and Recommendation of Pharmacopoeial Texts for Use in the International Conference on Harmonisation Regions; Annex on Test for Extractable Volume of Parenteral Preparations General Chapter; availability. Notice.

    Science.gov (United States)

    2009-01-09

    The Food and Drug Administration (FDA) is announcing the availability of a guidance entitled "Q4B Evaluation and Recommendation of Pharmacopoeial Texts for Use in the ICH Regions; Annex 2: Test for Extractable Volume of Parenteral Preparations General Chapter." The guidance was prepared under the auspices of the International Conference on Harmonisation of Technical Requirements for Registration of Pharmaceuticals for Human Use (ICH). The guidance provides the results of the ICH Q4B evaluation of the Test for Extractable Volume of Parenteral Preparations General Chapter harmonized text from each of the three pharmacopoeias (United States, European, and Japanese) represented by the Pharmacopoeial Discussion Group (PDG). The guidance conveys recognition of the three pharmacopoeial methods by the three ICH regulatory regions and provides specific information regarding the recognition. The guidance is intended to recognize the interchangeability between the local regional pharmacopoeias, thus avoiding redundant testing in favor of a common testing strategy in each regulatory region. In the Federal Register of February 21, 2008 (73 FR 9575), FDA made available a guidance on the Q4B process entitled "Q4B Evaluation and Recommendation of Pharmacopoeial Texts for Use in the ICH Regions."

  4. 基于大体积循环进样的低丰度蛋白质富集%Protein enrichment based on large volume recycling injection

    Institute of Scientific and Technical Information of China (English)

    张权青; 张磊; 高小迪; 张维冰; 张庆合

    2014-01-01

    发展了一种大体积循环进样方法,用于富集低丰度蛋白质。在优化的色谱分离条件下,通过增加蛋白质样品的上样体积提高低丰度蛋白质的绝对含量;进一步采用增加样品进样循环次数的方法提高蛋白质的富集效率。以猪肝提取蛋白质为样品,每次上样量500μL 的大体积11次循环进样。根据色谱峰的信号强弱,选择了在原始谱图中看不到色谱峰、有较少小峰和有较多小峰出现的时间段等有代表性的馏分进行研究。在中等极性的组分中,保留时间为11.38 min 和12.58 min 组分的富集效率分别提高了52倍和61倍,实验结果与理论富集效率相近。所发展的方法为生物蛋白质样品研究提供了一种新的富集制备及检测方法。%Biological proteins have great differences in size,hydrophobicity,pH and relative abundance. Especially,the relative contents of high-abundance proteins and low abundance proteins can reach 11 orders of magnitude or more in blood. However,the contents of proteins which have an important impact on the biological function and have related to major diseases are usually very low in body fluids or tissues. So,it is very meaningful to detect the low abun-dance proteins in biological samples. A method of large volume recycling injection was devel-oped as a new sample enrichment technology in this study. The low absolute contents of pro-teins in a sample were improved by increasing the volume of sample,and the enrichment effi-ciency was also increased with the addition of injection times. With the pork liver protein as an example,under the optimized conditions,the representative contents which were no peaks or little peaks and more peaks with low signals were studied. The contents of peaks at the reten-tion times of 11. 38 min and 12. 58 min were enriched by 11 time injections of 500 μL each time. The enrichment factors respectively reached 52 and 61 which were closed to

  5. Hippocampal volume is positively associated with behavioural inhibition (BIS) in a large community-based sample of mid-life adults: the PATH through life study.

    Science.gov (United States)

    Cherbuin, Nicolas; Windsor, Tim D; Anstey, Kaarin J; Maller, Jerome J; Meslin, Chantal; Sachdev, Perminder S

    2008-09-01

    The fields of personality research and neuropsychology have developed with very little overlap. Gray and McNaughton were among the first to recognize that personality traits must have neurobiological correlates and developed models relating personality factors to brain structures. Of particular note was their description of associations between conditioning, inhibition and activation of behaviours, and specific neural structures such as the hippocampus, amygdala and the prefrontal cortex. The aim of this study was to determine whether personality constructs representing the behavioural inhibition and activation systems (BIS/BAS) were associated with volumetric measures of the hippocampus and amygdala in humans. Amygdalar and hippocampal volumes were measured in 430 brain scans of cognitively intact community-based volunteers. Linear associations between brain volumes and the BIS/BAS measures were assessed using multiple regression, controlling for age, sex, education, intra-cranial and total brain volume. Results showed that hippocampal volumes were positively associated with BIS sensitivity and to a lesser extent with BAS sensitivity. No association was found between amygdalar volume and either the BIS or BAS. These findings add support to the model of Gray and McNaughton, which proposes a role of the hippocampus in the regulation of defensive/approach behaviours and trait anxiety but suggest an absence of associations between amygdala volume and BIS/BAS measures.

  6. Influence of volume percentage of NanoTiB2 particles on tribological & mechanical behaviour of 6061-T6 Al alloy nano-surface composite layer prepared via friction stir process

    Directory of Open Access Journals (Sweden)

    V. Kishan

    2017-02-01

    Full Text Available The aim of present study is to analyze the influence of volume percentage (vol.% of nano-sized particles (TiB2: average size is 35 nm on microstructure, mechanical and tribological behavior of 6061-T6 Al alloy surface nano composite prepared via Friction stir process (FSP. The microstructure of the fabricated surface nanocomposites is examined using optical microscopy (OM and scanning electron microscope (SEM for distribution of TiB2 nano reinforcement particles, thickness of nano composite layer formed on the Aluminum alloy substrate and fracture features. The depth of surface nano composite layer is measured as 3683.82 μm along the cross section of stir zone of nano composite perpendicular to FSP. It was observed that increase in volume percentage of TiB2 particles, the microhardness is increased up to 132 Hv and it is greater than as-received Al alloy's microhardness (104 Hv. It is also observed that at 4 volume percentage higher tensile properties exhibited as compared with the 2 and 8 vol. %. It is found that high wear resistance exhibited at 4 volume percentage as-compared with the 2 and 8 vol. %. The observed wear and mechanical properties are interrelated with microstructure, fractography and worn morphology.

  7. Semisynthetic preparation and isolation of dimeric procyanidins B1-B8 from roasted hazelnut skins (Corylus avellana L.) on a large scale using countercurrent chromatography.

    Science.gov (United States)

    Esatbeyoglu, Tuba; Juadjur, Andreas; Wray, Victor; Winterhalter, Peter

    2014-07-23

    Dimeric procyanidins B1-B8 were produced via semisynthesis from a polymeric proanthocyanidin fraction of hazelnut skins (Corylus avellana L.). This polymeric fraction was found to consist mostly of (+)-catechin and (-)-epicatechin as upper units. Therefore, according to the choice of nucleophile agent, it is possible to semisynthesize dimeric procyanidins B1, B3, B6, and B7 with (+)-catechin and B2, B4, B5, and B8 with (-)-epicatechin. The semisynthetic mixtures were separated on a preparative scale using high-speed countercurrent chromatography (HSCCC) and low-speed rotary countercurrent chromatography (LSRCCC). C4 → C8 linked dimeric procyanidins B1-B4 were isolated in amounts of 350-740 mg. To the best of the authors' knowledge this is the first study isolating dimeric procyanidins B1-B8 in large amounts with countercurrent chromatography. Moreover, the dimeric prodelphinidins B1, B2, and B3 and their structural elucidation by (1)H NMR spectroscopy without derivatization are described for hazelnuts as natural compounds for the first time.

  8. Metastable tetragonal Cu2Se hyperbranched structures: large-scale preparation and tunable electrical and optical response regulated by phase conversion.

    Science.gov (United States)

    Zhu, Jinbao; Li, Qiuyang; Bai, Liangfei; Sun, Yongfu; Zhou, Min; Xie, Yi

    2012-10-08

    Despite the promising applications of copper selenide nanoparticles, an in-depth elucidation of the inherent properties of tetragonal Cu(2)Se (β-Cu(2)Se) has not been performed because of the lack of a facile synthesis on the nanoscale and an energy-intensive strategy is usually employed. In this work, a facile wet-chemical strategy, employing HCOOH as reducing agent, has been developed to access single-crystalline metastable β-Cu(2)Se hyperbranched architectures for the first time. The process avoids hazardous chemistry and high temperatures, and thus opens up a facile approach to the large-scale low-cost preparation of metastable β-Cu(2)Se hyperbranched architectures. A possible growth mechanism to explain the formation of the β-Cu(2)Se dendritic morphology has been proposed based on time-dependent shape evolution. Further investigations revealed that the metastable β-Cu(2)Se can convert into the thermodynamically more stable cubic α-Cu(2-x)Se maintaining the dendritic morphology. An increase in electrical conductivity and a tunable optical response were observed under ambient conditions. This behavior can be explained by the oxidation of the surface of the β-Cu(2)Se hyperbranched structures, ultimately leading to solid-state phase conversion from β-Cu(2)Se into superionic conductor α-Cu(1.8)Se, which has potential applications in energy-related devices and sensors.

  9. High Purity and Large-scale Preparation of β-Ga2O3 Nanowires and Nanosheets by CVD and Their Raman and Photoluminescence Characteristics

    Institute of Scientific and Technical Information of China (English)

    YU Zhou; GONG Min; SUN Xiao-song; YANG Zhi-mei; CHEN Hao; WU Zhan-wen; JIN Yong; JIAO Zhi-feng; HE Yi; WANG Hui; LIU Jun-gang

    2007-01-01

    Ga2O3 nano-structures,nanowires and nanosheets are produced on Au pre-coated(111) silicon substrates with chemical vapor deposition(CVD) technique.By evaporating pure Ga powder in the H2O atmosphere under ambient pressure the large-scale preparation of β-Ga2O3 with monoclinic crystalline structure is achieved.The crystalline structures and morphologies of produced Ga2O3 nano-structures are characterized by means of scanning electron microscope(SEM),X-ray diffraction(XRD),selected area electron diffraction(SAED) and transmission electron microscope(TEM).Raman spectrum reveals the typical vibration modes of Ga2O3.The vibration mode shifts corresponding to Ga2O3 nano-structures are not found.Two distinguish photoluminescence(PL) emissions are found at about 399 nm and 469 nm owing to the VO-VGa excitation and VO-VGa-O excitation,respectively.The growth mechanisms of Ga2O3 nanowires and nanosheets are discussed with vapor-liquid-solid(VLS) and vapor-solid(VS) mechanisms.

  10. Preparation of graphitic carbon nitride with large specific surface area and outstanding N2 photofixation ability via a dissolve-regrowth process

    Science.gov (United States)

    Ma, Huiqiang; Shi, Zhenyu; Li, Qiang; Li, Shuang

    2016-12-01

    Nitrogen fixation is the second most important chemical process in nature next to photosynthesis. Here, we report a convenient dissolve-regrowth method for synthesizing graphitic carbon nitride (g-C3N4) with a large surface area and nitrogen vacancies by HCl treatment. XRD, N2adsorption, SEM, TEM, UV-Vis spectroscopy, EPR, N2-TPD, Photoluminescence and Photocurrent were used to characterize the prepared catalysts. The results indicate that HCl treatment does not influence the crystal phase of g-C3N4 but change the morphology and optical property, leading to the smaller particle size, larger surface area and increased bang gap energy. It is deduced by N2-TPD, Photoluminescence, Photocurrent and DFT simulations that the nitrogen vacancies formed by the HCl treatment not only serve as active sites to adsorb and activate N2 molecules but also promote interfacial charge transfer from g-C3N4to N2 molecules. The HCl treated g-C3N4 catalyst exhibits outstanding nitrogen photofixation ability under visible light, which is 13.4-fold higher than that of bulk g-C3N4 without nitrogen vacancy. The possible reaction mechanism is proposed.

  11. A system for accurate and automated injection of hyperpolarized substrate with minimal dead time and scalable volumes over a large range

    Science.gov (United States)

    Reynolds, Steven; Bucur, Adriana; Port, Michael; Alizadeh, Tooba; Kazan, Samira M.; Tozer, Gillian M.; Paley, Martyn N. J.

    2014-02-01

    Over recent years hyperpolarization by dissolution dynamic nuclear polarization has become an established technique for studying metabolism in vivo in animal models. Temporal signal plots obtained from the injected metabolite and daughter products, e.g. pyruvate and lactate, can be fitted to compartmental models to estimate kinetic rate constants. Modeling and physiological parameter estimation can be made more robust by consistent and reproducible injections through automation. An injection system previously developed by us was limited in the injectable volume to between 0.6 and 2.4 ml and injection was delayed due to a required syringe filling step. An improved MR-compatible injector system has been developed that measures the pH of injected substrate, uses flow control to reduce dead volume within the injection cannula and can be operated over a larger volume range. The delay time to injection has been minimized by removing the syringe filling step by use of a peristaltic pump. For 100 μl to 10.000 ml, the volume range typically used for mice to rabbits, the average delivered volume was 97.8% of the demand volume. The standard deviation of delivered volumes was 7 μl for 100 μl and 20 μl for 10.000 ml demand volumes (mean S.D. was 9 ul in this range). In three repeat injections through a fixed 0.96 mm O.D. tube the coefficient of variation for the area under the curve was 2%. For in vivo injections of hyperpolarized pyruvate in tumor-bearing rats, signal was first detected in the input femoral vein cannula at 3-4 s post-injection trigger signal and at 9-12 s in tumor tissue. The pH of the injected pyruvate was 7.1 ± 0.3 (mean ± S.D., n = 10). For small injection volumes, e.g. less than 100 μl, the internal diameter of the tubing contained within the peristaltic pump could be reduced to improve accuracy. Larger injection volumes are limited only by the size of the receiving vessel connected to the pump.

  12. A system for accurate and automated injection of hyperpolarized substrate with minimal dead time and scalable volumes over a large range☆

    Science.gov (United States)

    Reynolds, Steven; Bucur, Adriana; Port, Michael; Alizadeh, Tooba; Kazan, Samira M.; Tozer, Gillian M.; Paley, Martyn N.J.

    2014-01-01

    Over recent years hyperpolarization by dissolution dynamic nuclear polarization has become an established technique for studying metabolism in vivo in animal models. Temporal signal plots obtained from the injected metabolite and daughter products, e.g. pyruvate and lactate, can be fitted to compartmental models to estimate kinetic rate constants. Modeling and physiological parameter estimation can be made more robust by consistent and reproducible injections through automation. An injection system previously developed by us was limited in the injectable volume to between 0.6 and 2.4 ml and injection was delayed due to a required syringe filling step. An improved MR-compatible injector system has been developed that measures the pH of injected substrate, uses flow control to reduce dead volume within the injection cannula and can be operated over a larger volume range. The delay time to injection has been minimized by removing the syringe filling step by use of a peristaltic pump. For 100 μl to 10.000 ml, the volume range typically used for mice to rabbits, the average delivered volume was 97.8% of the demand volume. The standard deviation of delivered volumes was 7 μl for 100 μl and 20 μl for 10.000 ml demand volumes (mean S.D. was 9 ul in this range). In three repeat injections through a fixed 0.96 mm O.D. tube the coefficient of variation for the area under the curve was 2%. For in vivo injections of hyperpolarized pyruvate in tumor-bearing rats, signal was first detected in the input femoral vein cannula at 3–4 s post-injection trigger signal and at 9–12 s in tumor tissue. The pH of the injected pyruvate was 7.1 ± 0.3 (mean ± S.D., n = 10). For small injection volumes, e.g. less than 100 μl, the internal diameter of the tubing contained within the peristaltic pump could be reduced to improve accuracy. Larger injection volumes are limited only by the size of the receiving vessel connected to the pump. PMID:24355621

  13. Fabrication of large-volume, low-cost ceramic lanthanum halide scintillators for gamma ray detection : final report for DHS/DNDO/TRDD project TA-01-SL01.

    Energy Technology Data Exchange (ETDEWEB)

    Boyle, Timothy J.; Ottley, Leigh Anna M.; Yang, Pin; Chen, Ching-Fong; Sanchez, Margaret R.; Bell, Nelson Simmons

    2008-10-01

    , translucent LaBr{sub 3} ceramics samples (3-inch diameter, > 1/8-inch thick) were fabricated by hot pressing, demonstrating the superior manufacturability of the ceramic approach over single crystal growth methods in terms of size capability and cost. (6) Despite all these advances, evidence has shown that LaBr{sub 3} is thermally unstable at temperatures required for the densification process. This is particularly true for material near the surface where lattice defects and color centers can be created as bromine becomes volatile at high temperatures. Consequently, after densification these samples made using chemically prepared ultrafine powders turned black. An additional thermal treatment in a flowing bromine condition proved able to reduce the darkness of the surface layer for these densified samples. These observations demonstrated that although finer ceramic powders are desirable for densification due to a stronger driving force from their large surface areas, the same desirable factor can lead to lattice defects and color centers when these powders are densified at higher temperatures where material near the surface becomes thermally unstable.

  14. Stability of ischemic core volume during the initial hours of acute large vessel ischemic stroke in a subgroup of mechanically revascularized patients

    Energy Technology Data Exchange (ETDEWEB)

    Finitsis, Stephanos [Universitaetsklinikum Hamburg-Eppendorf, Neuroradiologie, Hamburg (Germany); Aristotle University of Thessaloniki, Neuroradiology Department, Ahepa Hospital, Thessaloniki (Greece); Kemmling, Andrea; Fiehler, Jens; Brekenfeld, Caspar [Universitaetsklinikum Hamburg-Eppendorf, Neuroradiologie, Hamburg (Germany); Havemeister, Stephanie; Thomalla, Goetz [Universitaetsklinikum Hamburg-Eppendorf, Klinik und Poliklinik fuer Neurologie, Kopf- und Neurozentrum, Hamburg (Germany)

    2014-04-15

    This study aimed to relate growth of the infarct core with time to recanalization in patients receiving mechanical recanalization in whom the time of recanalization is known. We analyzed data from patients with anterior circulation acute ischemic stroke who underwent mechanical recanalization. Demographic and angiographic characteristics, initial apparent diffusion coefficient (ADC) infarct volume, time-to-peak defect volume, revascularization grade, 24-48 h nonenhanced computed tomography (CT) infarct volume, symptom onset to recanalization time, diffusion-weighted imaging to recanalization time, and discharge National Institutes of Health Stroke Scale (NIHSS) and modified Rankin Scale (mRS) scores were compared between minimal and substantial infarct growth groups. Substantial infarct growth was defined as an increase of infarct volume >10 cm{sup 3} assessed by subtracting initial ADC infarct core volume from infarct volume at 24-48 h CT. Of 25 patients, 9 had minimal infarct growth (median 0 cm{sup 3}, interquartile range (IQR) -3 to 5 cm{sup 3}) and 16 had substantial infarct growth (median 103 cm{sup 3}, IQR 48-132 cm{sup 3}). Patients with minimal infarct growth had a median time from symptom onset to recanalization of 329 min (IQR 314-412 min) and a median time from imaging to recanalization of 231 min (IQR 198-309 min). On univariate analysis, minimal infarct growth was related to male gender (p = 0.04), smaller initial ADC volume (p = 0.04), higher recanalization grade (p < 0.001), and lower discharge NIHSS (p = 0.04) and mRS grades (p = 0.04). There was no or minimal infarct core growth in at least one third of patients despite an exceptionally long median time from magnetic resonance imaging to recanalization of almost 4 h. (orig.)

  15. ISABELLE. Volume 4. Detector R and D

    Energy Technology Data Exchange (ETDEWEB)

    1981-01-01

    Workshop participants were asked to assess the current status of detector R and D in terms of the specific needs for ISABELLE experiments: the demands of high particle rates, extremely selective triggers on complex and rare events, and the economics of large detector systems. The detailed results of working groups convened to consider specific areas of detector development are presented. The key points of this assessment, as regards the continuing R and D program for ISABELLE are summarized here. Twenty-six items from the volume were prepared separately for the data base, along with five items previously prepared. (GHT)

  16. Developing a semi/automated protocol to post-process large volume, High-resolution airborne thermal infrared (TIR) imagery for urban waste heat mapping

    Science.gov (United States)

    Rahman, Mir Mustafizur

    In collaboration with The City of Calgary 2011 Sustainability Direction and as part of the HEAT (Heat Energy Assessment Technologies) project, the focus of this research is to develop a semi/automated 'protocol' to post-process large volumes of high-resolution (H-res) airborne thermal infrared (TIR) imagery to enable accurate urban waste heat mapping. HEAT is a free GeoWeb service, designed to help Calgary residents improve their home energy efficiency by visualizing the amount and location of waste heat leaving their homes and communities, as easily as clicking on their house in Google Maps. HEAT metrics are derived from 43 flight lines of TABI-1800 (Thermal Airborne Broadband Imager) data acquired on May 13--14, 2012 at night (11:00 pm--5:00 am) over The City of Calgary, Alberta (˜825 km 2) at a 50 cm spatial resolution and 0.05°C thermal resolution. At present, the only way to generate a large area, high-spatial resolution TIR scene is to acquire separate airborne flight lines and mosaic them together. However, the ambient sensed temperature within, and between flight lines naturally changes during acquisition (due to varying atmospheric and local micro-climate conditions), resulting in mosaicked images with different temperatures for the same scene components (e.g. roads, buildings), and mosaic join-lines arbitrarily bisect many thousands of homes. In combination these effects result in reduced utility and classification accuracy including, poorly defined HEAT Metrics, inaccurate hotspot detection and raw imagery that are difficult to interpret. In an effort to minimize these effects, three new semi/automated post-processing algorithms (the protocol) are described, which are then used to generate a 43 flight line mosaic of TABI-1800 data from which accurate Calgary waste heat maps and HEAT metrics can be generated. These algorithms (presented as four peer-reviewed papers)---are: (a) Thermal Urban Road Normalization (TURN)---used to mitigate the microclimatic

  17. PS-b-PEO/Silica Films with Regular and Reverse Mesostructures of Large Characteristic Length Scales Prepared by Solvent Evaporation-Induced Self-Assembly

    Energy Technology Data Exchange (ETDEWEB)

    YU,KUI; BRINKER,C. JEFFREY; HURD,ALAN J.; EISENBERG,ADI

    2000-11-22

    Since the discovery of surfactant-templated silica by Mobil scientists in 1992, mesostructured silica has been synthesized in various forms including thin films, powders, particles, and fibers. In general, mesostructured silica has potential applications, such as in separation, catalysis, sensors, and fluidic microsystems. In respect to these potential applications, mesostructured silica in the form of thin films is perhaps one of the most promising candidates. The preparation of mesostructured silica films through preferential solvent evaporation-induced self-assembly (EISA) has recently received much attention in the laboratories. However, no amphiphile/silica films with reverse mesophases have ever been made through this EISA procedure. Furthermore, templates employed to date have been either surfactants or poly(ethylene oxide)-b-poly(propylene oxide)-b-poly(ethylene oxide) triblock copolymers, such as pluronic P-123, both of which are water-soluble and alcohol-soluble. Due to their relatively low molecular weight, the templated silica films with mesoscopic order have been limited to relatively small characteristic length scales. In the present communication, the authors report a novel synthetic method to prepare mesostructured amphiphilic/silica films with regular and reverse mesophases of large characteristic length scales. This method involves evaporation-induced self-assembly (EISA) of amphiphilic polystyrene-block-poly(ethylene oxide) (PS-b-PEO) diblock copolymers. In the present study, the PS-b-PEO diblocks are denoted as, for example, PS(215)-b-PEO(100), showing that this particular sample contains 215 S repeat units and 100 EO repeat units. This PS(215)-b-PEO(100) diblock possesses high molecular weight and does not directly mix with water or alcohol. To the authors knowledge, no studies have reported the use of water-insoluble and alcohol-insoluble amphiphilic diblocks as structure-directing agents in the synthesis of mesostructured silica films through

  18. Physiologic effects of bowel preparation

    DEFF Research Database (Denmark)

    Holte, Kathrine; Nielsen, Kristine Grubbe; Madsen, Jan Lysgård;

    2004-01-01

    as increased phosphate and urea concentrations, whereas calcium and potassium concentrations decreased significantly after bowel preparation. No differences in plasma or extracellular volumes were seen. Orthostatic tolerance and balance function did not change after bowel preparation. CONCLUSIONS: Bowel...

  19. Association between hospital procedure volume and early complications after pacemaker implantation: results from a large, unselected, contemporary cohort of the German nationwide obligatory external quality assurance programme.

    Science.gov (United States)

    Nowak, Bernd; Tasche, Karl; Barnewold, Linda; Heller, Günther; Schmidt, Boris; Bordignon, Stefano; Chun, K R Julian; Fürnkranz, Alexander; Mehta, Rajendra H

    2015-05-01

    Several studies demonstrated an inverse relationship between cardioverter-defibrillator implantation volume and complication rates, suggesting better outcomes for higher volume centres. However, the association of institutional procedural volume with patient outcomes for permanent pacemaker (PPM) implantation remains less known, especially in decentralized implantation systems. We performed retrospective examination of data on patients undergoing PPM from the German obligatory quality assurance programme (2007-12) to evaluate the relationship of hospital PPM volume (categorized into quintiles of their mean annual volume) with risk-adjusted in-hospital surgical complications (composite of pneumothorax, haemothorax, pericardial effusion, or pocket haematoma, all requiring intervention, or device infection) and pacemaker lead dislocation. Overall 430 416 PPM implantations were documented in 1226 hospitals. Systems included dual (72.8%) and single (25.8%) chamber PPM and cardiac resynchronization therapy (CRT) devices (1.1%). Complications included surgical (0.92%), and ventricular (0.99%), and atrial (1.22%) lead dislocation. Despite an increase in relatively complex procedures (dual chamber, CRT), there was a significant decrease in the procedural and fluoroscopy times and complications from lowest to highest implantation volume quintiles (P for trend <0.0001). The greatest difference was observed between the lowest (1-50 implantations/year-reference group) and the second-lowest (51-90 implantations/year) quintile: surgical complications [odds ratio (OR) 0.69; confidence interval (CI) 0.60-0.78], atrial lead dislocations (OR 0.69; CI 0.59-0.80), and ventricular lead dislocations (OR 0.73; CI 0.63-0.84). Hospital annual PPM volume was directly related to indication-based implantation of relatively more complex PPM and yet inversely with procedural times and rates of early surgical complications and lead dislocations. Thus, our data suggest better performance and lower

  20. 大输液包装材质与注射用药物相容性研究进展与思考%Research Advance and Investigation on Compatibility of Large Volume Parenteral Solution Package Material with Injectable Drugs

    Institute of Scientific and Technical Information of China (English)

    徐帆; 杨伶俐; 毛盼盼; 喻琼丽

    2014-01-01

    目的:促进临床合理用药。方法调研相关文献,分析不同包装材质大输液的性质、特点及其对注射用药物的吸附性作用。结果与结论大输液作为临床治疗和静脉药物治疗不可缺少的载体或溶剂,在现代临床治疗中具有极其重要的地位,临床医务人员已逐渐开始关注药物与大输液包装材质的相容性与安全性。目前,我国医疗市场多种材质包装的大输液并存。临床医务人员应更加准确地把握不同包装材质大输液的特性,静脉用药物治疗时选择适当包装材质的大输液,以确保患者输液安全。%Objective To promote the rational drug use. Methods By investigating and consulting the related literature,the properties, characteristics and adsorptive effect on injectable drugs of the large volume parenteral solution package materials were analyzed. Results and Conclusion The large volume parenteral solution as the indispensable carrier or solvent possesses the extreme important status in the modern clinical treatment. The clinical medical staffs have gradually begin to pay close attention to the compatibility and safety of drugs and the large volume parenteral solution package materials. At present,the large volume parenteral solutions packaged by various materials coexist in the medical market of our country. The clinical medical staffs should more accurately grasp the characteristics of the large volume parenteral solutions with different package materials. Intravenous medication should select the large volume parenteral solu-tions with the proper package materials for ensuring the intravenous infusion safety of patients.

  1. 高比容量镍氢电池的制备及电化学性能%Preparation and electrochemical Performances of nickel metal hydride batteries with high specific volume capacity

    Institute of Scientific and Technical Information of China (English)

    杨敏杰; 南俊民; 侯宪鲁; 李伟善

    2008-01-01

    Cylindrical nickel metal hydride (Ni-MH) battery with high specific volume capacity was prepared by using the oxyhydroxide Ni(OH)2 and AB5 type hydrogen storage alloy and adjusting the designing parameters of positive and negative electrodes. The oxyhydroxide Ni(OH)2 was synthesized by oxidizing spherical β-Ni(OH)2 with chemical method. The X-ray diffraction (XRD) patterns and the Fourier transform infrared (FT-IR) spectra indicated that γ-NiOOH was formed on the oxyhydroxide Ni(OH)2 powders, and some H2O molecules were inserted into their crystal lattice spacing. The battery capacity could not be improved when the oxyhydroxide Ni(OH)2 sample was directly used as the positive active materials. However, based on the conductance and residual capacity of the oxyhydroxide Ni(OH)2 powders, AA size Ni-MH battery with 2560 mA·h capacity and 407 W·h·L specific volume energy at 0.2C was obtained by using the commercial spherical β-Ni(OH)2 and AB5-type hydrogen-storage alloy powders as the active materials when 10% mass amount of the oxyhydroxide Ni(OH)2 with 2.50 valence was added to the positive active materials and subsequently the battery designing parameters were adjusted as well. The as-prepared battery showed 70% initial capacity after 80 cycles at 0.5C. The possibility for adjusting the capacity ratio of positive and negative electrodes from 1 : 1.35 to 1 : 1.22 was demonstrated preliminarily. It is considered the as-prepared battery can meet the requirement of some special portable electrical instruments.

  2. Intra-articular administration of hyaluronic acid increases the volume of the hyaline cartilage regenerated in a large osteochondral defect by implantation of a double-network gel.

    Science.gov (United States)

    Fukui, Takaaki; Kitamura, Nobuto; Kurokawa, Takayuki; Yokota, Masashi; Kondo, Eiji; Gong, Jian Ping; Yasuda, Kazunori

    2014-04-01

    Implantation of PAMPS/PDMAAm double-network (DN) gel can induce hyaline cartilage regeneration in the osteochondral defect. However, it is a problem that the volume of the regenerated cartilage tissue is gradually reduced at 12 weeks. This study investigated whether intra-articular administration of hyaluronic acid (HA) increases the volume of the cartilage regenerated with the DN gel at 12 weeks. A total of 48 rabbits were used in this study. A cylindrical osteochondral defect created in the bilateral femoral trochlea was treated with DN gel (Group DN) or left without any implantation (Group C). In both Groups, we injected 1.0 mL of HA in the left knee, and 1.0 mL of saline solution in the right knee. Quantitative histological evaluations were performed at 2, 4, and 12 weeks, and PCR analysis was performed at 2 and 4 weeks after surgery. In Group DN, the proteoglycan-rich area was significantly greater in the HA-injected knees than in the saline-injected knees at 12 weeks (P = 0.0247), and expression of type 2 collagen, aggrecan, and Sox9 mRNAs was significantly greater in the HA-injected knees than in the saline-injected knees at 2 weeks (P = 0.0475, P = 0.0257, P = 0.0222, respectively). The intra-articular administration of HA significantly enhanced these gene expression at 2 weeks and significantly increased the volume of the hyaline cartilage regenerated by implantation of a DN gel at 12 weeks. This information is important to develop an additional method to increase the volume of the hyaline cartilage tissue in a potential cartilage regeneration strategy using the DN gel.

  3. Environmental Report 1996, Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    Harrach, R.J.

    1996-01-01

    This is Volume 2 of the Lawrence Livermore National Laboratory`s (LLNL`s) annual Environmental Report 1996, prepared for the US Department of Energy. Volume 2 supports Volume 1 summary data and is essentially a detailed data report that provides individual data points, where applicable. Volume 2 includes information on monitoring of air, air effluents, sewerable water, surface water, ground water, soil and sediment, vegetation and foodstuff, environmental radiation, and quality assurance.

  4. Evaluation of Clensia(®), a new low-volume PEG bowel preparation in colonoscopy: Multicentre randomized controlled trial versus 4L PEG.

    Science.gov (United States)

    Spada, Cristiano; Cesaro, Paola; Bazzoli, Franco; Saracco, Giorgio Maria; Cipolletta, Livio; Buri, Luigi; Crosta, Cristiano; Petruzziello, Lucio; Ceroni, Liza; Fuccio, Lorenzo; Giordanino, Chiara; Elia, Chiara; Rotondano, Gianluca; Bianco, Maria A; Simeth, Catrin; Consalvo, Danilo; De Roberto, Giuseppe; Fiori, Giancarla; Campanale, Mariachiara; Costamagna, Guido

    2017-06-01

    Success of colonoscopy is linked to the adequacy of bowel cleansing. Polyethylene glycol 4L (PEG 4L) solutions are widely used for colonic cleansing but with limitations concerning tolerability and acceptability. To demonstrate the equivalence of a new low-volume PEG containing citrates and simeticone (Clensia) versus a standard PEG 4L. In this, multicentre, randomised, observer-blind trial, patients received either Clensia 2L or PEG 4L solution. Primary endpoint was the proportion of patients with colon cleansing evaluated as excellent or good. 422 patients received Clensia (n=213) or PEG 4L (n=209). Rate of excellent/good bowel cleansing was 73.6% and 72.3% in Clensia and PEG 4L group respectively. Clensia was demonstrated to be equivalent to PEG 4L. No SAEs were observed. Clensia showed better gastrointestinal tolerability (37.0% vs 25.4%). The acceptability was significantly better with Clensia in terms of proportion of subjects who felt no distress (Clensia 72.8% vs PEG 4L 63%, P=0.0314) and willingness-to-repeat (93.9% vs 82.2%, P=0.0002). The rate of optimal compliance was similar with both formulations (91.1% for Clensia vs 90.9% for PEG 4L, P=0.9388). The low-volume Clensia is equally effective and safe in bowel cleansing compared to the standard PEG 4L, with better gastrointestinal tolerability and acceptability. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

  5. Small-volume storage facilities as alternative flexibility instruments in the procurement portfolio of large natural gas suppliers; Kleinvolumige Speicher als alternative Flexibilitaetsinstrumente im Bezugsportfolio grosser Erdgasversorger

    Energy Technology Data Exchange (ETDEWEB)

    Deschkan, Peter [WIEN ENERGIE Speicher GmbH, Wien (Austria)

    2012-11-15

    This article analyses the positive economic effects of small-volume storage facilities on the management of the medium to long-term natural gas procurement portfolio of a major urban supplier in the context of the liberalized Austrian market in natural gas. Due to low investment and operating costs and short construction times, these facilities represent attractive possibilities, for instance for public utility companies, in structuring their natural gas procurement. However, unlike storage products normally available on the market, which also facilitate seasonal balancing between supply and demand, they can only be used in the context of influencing the daily and hourly loads (peak shaving). Below, we examine the effects of including small-volume storage facilities (such as pipe storage) on the cost situation of the natural gas supplier for various consumption patterns and customer structures, as part of an optimization model. The results of the analysis indicate the obvious benefits in the case of load patterns strongly influenced by temperature that decline significantly with decreasing share of heating load. (orig.)

  6. Preparation of drug-in-cyclodextrin-in-liposomes at a large scale using a membrane contactor: Application to trans-anethole.

    Science.gov (United States)

    Gharib, Riham; Greige-Gerges, Hélène; Jraij, Alia; Auezova, Lizette; Charcosset, Catherine

    2016-12-10

    The present study aimed to prepare liposomes loaded with cyclodextrin/drug inclusion complexes at a pilot scale based on the ethanol injection technique. Anethole (ANE), a major component of anise and fennel essential oils, was used as a model of a volatile and highly hydrophobic drug. Membrane contactor (600mL) and a pilot plant (3L) were used for liposome production. The liposome preparations obtained were characterized for size, polydispersity index, zeta potential, morphology, stability and ANE release rate. All experimental set-ups were shown to be appropriate for the preparation of small, multilamellar vesicles with narrow size distribution and good stability at 4°C. The drug release study showed that only a small amount of ANE was released from liposome formulations after 21days of storage at 4°C. The loading rate of ANE was higher when ethanol was evaporated directly on the pilot plant compared to a rotary evaporation.

  7. Optimized determination of trace jet fuel volatile organic compounds in human blood using in-field liquid-liquid extraction with subsequent laboratory gas chromatographic-mass spectrometric analysis and on-column large-volume injection.

    Science.gov (United States)

    Liu, S; Pleil, J D

    2001-03-05

    A practical and sensitive method to assess volatile organic compounds (VOCs) from JP-8 jet fuel in human whole blood was developed by modifying previously established liquid-liquid extraction procedures, optimizing extraction times, solvent volume, specific sample processing techniques, and a new on-column large-volume injection method for GC-MS analysis. With the optimized methods, the extraction efficiency was improved by 4.3 to 20.1 times and the detection sensitivity increased up to 660 times over the standard method. Typical detection limits in the parts-per-trillion (ppt) level range were achieved for all monitored JP-8 constituents; this is sufficient for assessing human fuels exposures at trace environmental levels as well as occupational exposure levels. The sample extractions are performed in the field and only solvent extracts need to be shipped to the laboratory. The method is implemented with standard biological laboratory equipment and a modest bench-top GC-MS system.

  8. Under conditions of large geometric miss, tumor control probability can be higher for static gantry intensity-modulated radiation therapy compared to volume-modulated arc therapy for prostate cancer

    Energy Technology Data Exchange (ETDEWEB)

    Balderson, Michael, E-mail: michael.balderson@rmp.uhn.ca; Brown, Derek; Johnson, Patricia; Kirkby, Charles

    2016-07-01

    The purpose of this work was to compare static gantry intensity-modulated radiation therapy (IMRT) with volume-modulated arc therapy (VMAT) in terms of tumor control probability (TCP) under scenarios involving large geometric misses, i.e., those beyond what are accounted for when margin expansion is determined. Using a planning approach typical for these treatments, a linear-quadratic–based model for TCP was used to compare mean TCP values for a population of patients who experiences a geometric miss (i.e., systematic and random shifts of the clinical target volume within the planning target dose distribution). A Monte Carlo approach was used to account for the different biological sensitivities of a population of patients. Interestingly, for errors consisting of coplanar systematic target volume offsets and three-dimensional random offsets, static gantry IMRT appears to offer an advantage over VMAT in that larger shift errors are tolerated for the same mean TCP. For example, under the conditions simulated, erroneous systematic shifts of 15 mm directly between or directly into static gantry IMRT fields result in mean TCP values between 96% and 98%, whereas the same errors on VMAT plans result in mean TCP values between 45% and 74%. Random geometric shifts of the target volume were characterized using normal distributions in each Cartesian dimension. When the standard deviations were doubled from those values assumed in the derivation of the treatment margins, our model showed a 7% drop in mean TCP for the static gantry IMRT plans but a 20% drop in TCP for the VMAT plans. Although adding a margin for error to a clinical target volume is perhaps the best approach to account for expected geometric misses, this work suggests that static gantry IMRT may offer a treatment that is more tolerant to geometric miss errors than VMAT.

  9. A Coupled Mean Field / Gurson-Tvergaard Micromechanical Model For Ductile Fracture In Multiphase Materials With Large Volume Fraction of Voids

    Science.gov (United States)

    Van Hoof, Thibaut; Piérard, Olivier; Lani, Frédéric

    2007-04-01

    In the framework of the European project PROHIPP (New design and manufacturing processes for high pressure fluid power product — NMP 2-CT-2004-50546), CENAERO develops a library of constitutive models used to predict the mechanical response of a family of cast iron. The present contribution focuses on one particular microstructure, corresponding to a ferrite matrix containing spheroidal graphite and isolated inclusions of pearlite. An incremental mean field homogenisation scheme such as the one developed by Doghri and Ouaar is used. In the present application, the ferrite matrix is described by a Gurson type constitutive law (porous plasticity) while the pearlite inclusions are assumed to obey the classical isotropic J2 plasticity. The predictions of the micromechanical model are compared to the results of Finite Element simulations performed on three-dimensional representative volume elements (RVEs).

  10. Preparing the Next Generations of Technology Project Managers to Lead through Knowledge Sharing: A Case Study at a Large Transportation Company

    Science.gov (United States)

    Kargbo, Michelle

    2013-01-01

    The purpose of this research was to identify knowledge transfer gaps and current practices, prepare current project managers to accept the challenges associated with leadership opportunities that are coming available due to retirements through cross training efforts and succession planning, and to identify the proper management of knowledge…

  11. Glass-covering of large building volumes. An interdisciplinary evaluation of a shopping centre; Oeverglasning av stora byggnadsvolymer; En tvaervetenskaplig utvaerdering av ett koepcentrum

    Energy Technology Data Exchange (ETDEWEB)

    Oeman, R. [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Building Technology

    1993-11-01

    Systematized experiences of the function of large glass- covered spaces related to shopping centres, hotels, office buildings etc. are still relatively limited. With the glazed pedestrian precincts of the rebuilt Skaerholmen Centre in Stockholm as the main object of interdisciplinary studies, the aim of this thesis is to provide additional knowledge of large glass-covered spaces (atrium buildings). The studies comprises thermal comfort, temperature conditions, ventilation, energy balance, humidity - mycology, acoustics, operation - maintenance - durability and sociology. To sum up, it is clear that in the Scandinavian climate there is every likelihood of large glass-covered spaces in the public places functioning well from a technical as well as a social point of view. The energy consumption on heating the whole complex, based on theoretical calculations and measurement, is shown to have been reduced by the order of 10%. (author) figs., tabs., 101 refs

  12. The large scale antibacterial, antifungal and anti-phage efficiency of Petamcin-A: new multicomponent preparation for skin diseases treatment.

    Science.gov (United States)

    Ginovyan, Mikayel; Keryan, Andranik; Bazukyan, Inga; Ghazaryan, Petros; Trchounian, Armen

    2015-05-18

    Human and animal skin diseases of bacterial, fungal and viral nature and their complications are widespread and globally cause a serious trouble. Their prevalence is increasing mainly due to drug resistance. Consequently, demand has increased for new effective antimicrobial drugs, which also should be less toxic, possess a wider spectrum of action and be economically more beneficial. The goal was to investigate antibacterial, antifungal and anti-phage activity of Petamcin-A-a new multicomponent preparation. It contains acetic acid and hexamethylenetetramine as main active antimicrobial components, as well as phosphatidylcholine, tocopheryl acetate and glycerol as excipients. Bacteriostatic activity and minimal inhibitory concentrations of the preparation against various test-organisms were determined by agar well diffusion assay. Antifungal activity was tested by agar dilution assay. To explore anti-phage activity double agar overlay plaque assay was used. Nystatin, chlorhexidine and acetic acid were used as control agents for comparative analysis. Statistical analysis was done with GraphPad Prism 5.03 or R 3.1.0 software. The results showed a higher activity of Petamcin-A against all bacterial and fungal test strains compared with its components or control agents. The preparation was more effective against tested gram-positive bacteria than gram-negative ones. Petamcin-A expressed bactericidal activity against almost all test strains. In addition, the preparation demonstrated high activity against T4 phage of Escherichia coli C-T4 completely inhibiting its growth. 5-fold diluted Petamcin-A also exhibited considerable activity reducing phage concentration by 2.6 Log10. Petamcin-A has a high antimicrobial activity against all tested strains of bacteria, yeasts and moulds. The preparation also exhibited high anti-phage activity. Moreover, taking into account that Petamcin-A has no observable toxicity on skin and its components are not expensive, it can be

  13. Dose fractionated gamma knife radiosurgery for large arteriovenous malformations on daily or alternate day schedule outside the linear quadratic model: Proof of concept and early results. A substitute to volume fractionation.

    Science.gov (United States)

    Mukherjee, Kanchan Kumar; Kumar, Narendra; Tripathi, Manjul; Oinam, Arun S; Ahuja, Chirag K; Dhandapani, Sivashanmugam; Kapoor, Rakesh; Ghoshal, Sushmita; Kaur, Rupinder; Bhatt, Sandeep

    2017-01-01

    To evaluate the feasibility, safety and efficacy of dose fractionated gamma knife radiosurgery (DFGKRS) on a daily schedule beyond the linear quadratic (LQ) model, for large volume arteriovenous malformations (AVMs). Between 2012-16, 14 patients of large AVMs (median volume 26.5 cc) unsuitable for surgery or embolization were treated in 2-3 of DFGKRS sessions. The Leksell G frame was kept in situ during the whole procedure. 86% (n = 12) patients had radiologic evidence of bleed, and 43% (n = 6) had presented with a history of seizures. 57% (n = 8) patients received a daily treatment for 3 days and 43% (n = 6) were on an alternate day (2 fractions) regimen. The marginal dose was split into 2 or 3 fractions of the ideal prescription dose of a single fraction of 23-25 Gy. The median follow up period was 35.6 months (8-57 months). In the three-fraction scheme, the marginal dose ranged from 8.9-11.5 Gy, while in the two-fraction scheme, the marginal dose ranged from 11.3-15 Gy at 50% per fraction. Headache (43%, n = 6) was the most common early postoperative complication, which was controlled with short course steroids. Follow up evaluation of at least three years was achieved in seven patients, who have shown complete nidus obliteration in 43% patients while the obliteration has been in the range of 50-99% in rest of the patients. Overall, there was a 67.8% reduction in the AVM volume at 3 years. Nidus obliteration at 3 years showed a significant rank order correlation with the cumulative prescription dose (p 0.95, P value 0.01), with attainment of near-total (more than 95%) obliteration rates beyond 29 Gy of the cumulative prescription dose. No patient receiving a cumulative prescription dose of less than 31 Gy had any severe adverse reaction. In co-variate adjusted ordinal regression, only the cumulative prescription dose had a significant correlation with common terminology criteria for adverse events (CTCAE) severity (P value 0.04), independent of age, AVM volume

  14. Engineered materials characterization report, volume 3 - corrosion data and modeling update for viability assessments

    Energy Technology Data Exchange (ETDEWEB)

    McCright, R D

    1998-06-30

    This Engineered Materials Characterization Report (EMCR), Volume 3, discusses in considerable detail the work of the past 18 months on testing the candidate materials proposed for the waste-package (WP) container and on modeling the performance of those materials in the Yucca Mountain (YM) repository setting This report was prepared as an update of information and serves as one of the supporting documents to the Viability Assessment (VA) of the Yucca Mountain Project. Previous versions of the EMCR have provided a history and background of container-materials selection and evaluation (Volume I), a compilation of physical and mechanical properties for the WP design effort (Volume 2), and corrosion-test data and performance-modeling activities (Volume 3). Because the information in Volumes 1 and 2 is still largely current, those volumes are not being revised. As new information becomes available in the testing and modeling efforts, Volume 3 is periodically updated to include that information.

  15. Large-scale preparation of strawberry-like, AgNP-doped SiO2 microspheres using the electrospraying method

    Science.gov (United States)

    Ma, Zhijun; Ji, Huijiao; Tan, Dezhi; Dong, Guoping; Teng, Yu; Zhou, Jiajia; Guan, Miaojia; Qiu, Jianrong; Zhang, Ming

    2011-07-01

    In this paper, we report on a novel strategy for the preparation of silver nanoparticle-doped SiO2 microspheres (Ag-SMSs) with an interesting strawberry-like morphology using a simple and efficient electrospraying method. SEM (scanning electron microscopy), TEM (transmission electron microscopy), XRD (x-ray diffraction), EDS (energy-dispersive spectroscopy) and UV-vis spectra (ultraviolet-visible spectra) were applied to investigate the morphology, structure, composition and optical properties of the hybrid microspheres, and E. coli (Escherichia coli) was used as a model microbe to evaluate their antibacterial ability. The results showed that the Ag-SMSs were environmentally stable and washing resistant. The Ag-SMSs exhibited effective inhibition against proliferation of E. coli, and their antibacterial ability could be well preserved for a long time. The environmental stability, washing resistance, efficient antibacterial ability and simple but productive preparation method endowed the Ag-SMSs with great potential for practical biomedical applications.

  16. Volume Entropy

    CERN Document Server

    Astuti, Valerio; Rovelli, Carlo

    2016-01-01

    Building on a technical result by Brunnemann and Rideout on the spectrum of the Volume operator in Loop Quantum Gravity, we show that the dimension of the space of the quadrivalent states --with finite-volume individual nodes-- describing a region with total volume smaller than $V$, has \\emph{finite} dimension, bounded by $V \\log V$. This allows us to introduce the notion of "volume entropy": the von Neumann entropy associated to the measurement of volume.

  17. Determining the organ of origin of large pelvic masses in females using multidetector CT angiography and three-dimensional volume rendering CT angiography

    Energy Technology Data Exchange (ETDEWEB)

    Li, YangKang; Chen, JunWei; Chen, XueYin; Lin, JianBang; Cai, AiQun; Zhou, XiuGuo [Cancer Hospital, Shantou University Medical College, Department of Radiology, Shantou, Guangdong Province (China); Zheng, Yu [Cancer Hospital, Shantou University Medical College, Department of Clinical Pharmacology, Shantou (China)

    2015-04-01

    To study the value of tumour feeding arteries and the ovarian vein in determining the organ of origin of large pelvic tumours in females using multidetector CT. One hundred and thirty patients with 131 pathologically proven tumours (>6.5 cm) were retrospectively reviewed. Conventional CT images and CT angiography were evaluated, with focus on assessing the value of tumour feeding arteries and the ovarian vein in differentiating ovarian from non-ovarian tumours. For 97 ovarian tumours, the feeding arteries included the ovarian artery (n = 51) and the ovarian branch of uterine artery (n = 64). For 34 non-ovarian tumours, the feeding arteries included the ovarian artery (n = 2), the uterine artery (n = 21), the mesenteric artery (n = 5), and the internal iliac artery (n = 1). The ovarian vein was identified in 86 ovarian tumours and 12 non-ovarian tumours. When the feeding arteries and the ovarian vein were combined to confirm ovarian origin, the sensitivity, specificity, positive predictive value, negative predictive value, and accuracy were 97.8 %, 84.2 %, 93.8 %, 94.1 %, and 93.9 %, respectively. The accuracy was significantly higher than that of independently using the ovarian vein or the ovarian feeding arteries. Combined application of tumour feeding arteries and the ovarian vein is valuable to differentiate large ovarian from non-ovarian tumours. (orig.)

  18. Comparison of semipermeable membrane device (SPMD) and large-volume solid-phase extraction techniques to measure water concentrations of 4,4'-DDT, 4,4'-DDE, and 4,4'-DDD in Lake Chelan, Washington.

    Science.gov (United States)

    Ellis, Steven G; Booij, Kees; Kaputa, Mike

    2008-07-01

    Semipermeable membrane devices (SPMDs) spiked with the performance reference compound PCB29 were deployed 6.1 m above the sediments of Lake Chelan, Washington, for a period of 27 d, to estimate the dissolved concentrations of 4,4'-DDT, 4,4'-DDE, and 4,4'-DDD. Water concentrations were estimated using methods proposed in 2002 and newer equations published in 2006 to determine how the application of the newer equations affects historical SPMD data that used the older method. The estimated concentrations of DDD, DDE, and DDD calculated using the older method were 1.5-2.9 times higher than the newer method. SPMD estimates from both methods were also compared to dissolved and particulate DDT concentrations measured directly by processing large volumes of water through a large-volume solid-phase extraction device (Infiltrex 300). SPMD estimates of DDD+DDE+DDT (SigmaDDT) using the older and newer methods were lower than Infiltrex concentrations by factors of 1.1 and 2.3, respectively. All measurements of DDT were below the Washington State water quality standards for the protection of human health (0.59 ng l(-1)) and aquatic life (1.0 ng l(-1)).

  19. Study on the yellow bags after sterilization of packaging non -PVC large volume injections%非 PVC 软包装大容量注射剂灭菌后黄袋问题研究

    Institute of Scientific and Technical Information of China (English)

    周美丽; 宋艳萍; 臧恒昌

    2016-01-01

    By studying of non -PVC multi -layer co -extruded film properties,the sterilization process of non -PVC packaging of large volume injections and the characteristics of the water bath sterilizer,the authors found the reasons for making the bags yellow.And the issue on the yellow bags after sterilization of non -PVC packaging large volume injections can be solved by the Methods of transformation and regular cleaning.%通过研究非 PVC 多层共挤膜的特性、非 PVC 软包装大容量注射剂灭菌工艺、水浴灭菌柜的特点,找到造成黄袋问题的原因,通过改造灭菌柜及定期清洁等方法,解决非 PVC 软包装大容量注射剂灭菌后出现的黄袋问题。

  20. Moduli stabilization, large-volume dS minimum without D3-branes, (non-)supersymmetric black hole attractors and two-parameter Swiss cheese Calabi–Yau’s

    CERN Document Server

    Misra, A

    2008-01-01

    We consider two sets of issues in this paper. The first has to do with moduli stabilization, existence of “area codes” [A. Giryavets, New attractors and area codes, JHEP 0603 (2006) 020, hep-th/0511215] and the possibility of getting a non-supersymmetric dS minimum without the addition of -branes as in KKLT for type II flux compactifications. The second has to do with the “inverse problem” [K. Saraikin, C. Vafa, Non-supersymmetric black holes and topological strings, hep-th/0703214] and “fake superpotentials” [A. Ceresole, G. Dall'Agata, Flow equations for non-BPS extremal black holes, JHEP 0703 (2007) 110, hep-th/0702088] for extremal (non-)supersymmetric black holes in type II compactifications. We use (orientifold of) a “Swiss cheese” Calabi–Yau [J.P. Conlon, F. Quevedo, K. Suruliz, Large-volume flux compactifications: Moduli spectrum and D3/D7 soft supersymmetry breaking, JHEP 0508 (2005) 007, hep-th/0505076] expressed as a degree-18 hypersurface in WCP4[1,1,1,6,9] in the “large-volume...

  1. 大体积进样气相色谱法测定水中乙醛%Detection of acetaldehyde in water by large volume injection-gas chromatography process

    Institute of Scientific and Technical Information of China (English)

    陈璟士; 赵小敏

    2011-01-01

    试验采用大体积直接进样,气相色谱填充柱进行分离分析水中乙醛浓度.结果表明该方法分离度好、灵敏度高,水中乙醛检出限为0.01 mg/L,乙醛样品加标回收率为98.4%~108.4%;平行测定结果的相对标准差为4.1%(n=7).大体积进样气相色谱法简便、快速、准确、重现性好,适合于水体中乙醛的测定.%The acetaldehyde in water was separated and detected using the combined process of large volume injection and packed column gas chromatography. The results of the test showed that, the said process had good separable degree and high sensitivity, the detection limit of acetaldehyde was 0.01 mg/L, and the recovery of standard addition was 98.4% - 108.4%; the relative standard deviation got from the parallel determination was 4.1%(n = 7). It could be seen that, large volume injection-gas chromatography process had advantages of convenient, quick, accurate and good reproductivity, which was suitable for the detection of acetaldehyde in water.

  2. Assessment of generic solar thermal systems for large power applications. Volume II. Analysis of thermal energy production costs for systems from 50 to 600 MWt

    Energy Technology Data Exchange (ETDEWEB)

    Bird, S.P.; Apley, W.J.; Barnhart, J.S.; Brown, D.R.; Drost, M.K.; Fort, J.A.; Garrett-Price, B.A.; Williams, T.A.

    1981-06-01

    A comparative analysis of solar thermal concepts that are potentially suitable for development as large process heat systems (50 to 600 MWt) was performed. The concepts considered can be classified into three categories based on the type of solar tracking used by the collector: (1) two-axis tracking, in which concentrators track the sun's motion in both azimuth and altitude; (2) one-axis tracking, in which concentrators track changes in either azimuth or altitude; and (3) non-tracking, in which the concentrators are fixed. Seven generic types of collectors were considered. Conceptual designs developed for the seven systems were based on common assumptions of available technology in the 1990 to 2000 time frame. Costs were estimated on the basis of identical assumptions, ground rules, methodologies, and unit costs of materials and labor applied uniformly to all of the concepts.

  3. Comparison of procedures for immediate reconstruction of large osseous defects resulting from removal of a single tooth to prepare for insertion of an endosseous implant after healing

    NARCIS (Netherlands)

    Raghoebar, G. M.; Slater, J. J. H.; den Hartog, L.; Meijer, H. J. A.; Vissink, A.

    2009-01-01

    This study evaluated the treatment outcome of immediate reconstruction of 45 large osseous defects resulting from removal of a single tooth with a 1:2 mixture of Bio-Oss(R) and autologous tuberosity bone, and three different procedures for soft tissue closing (Bio-Gide(R) membrane, connective tissue

  4. Optimisation of a sol-gel synthesis route for the preparation of MgF2 particles for a large scale coating process.

    Science.gov (United States)

    Scheurell, K; Noack, J; König, R; Hegmann, J; Jahn, R; Hofmann, Th; Löbmann, P; Lintner, B; Garcia-Juan, P; Eicher, J; Kemnitz, E

    2015-12-07

    A synthesis route for the preparation of optically transparent magnesium fluoride sols using magnesium acetate tetrahydrate as precursor is described. The obtained magnesium fluoride sols are stable for several months and can be applied for antireflective coatings on glass substrates. Reaction parameters in the course of sol synthesis are described in detail. Thus, properties of the precursor materials play a crucial role in the formation of the desired magnesium fluoride nanoparticles, this is drying the precursor has to be performed under defined mild conditions, re-solvation of the dried precursor has to be avoided and addition of water to the final sol-system has to be controlled strictly. Important properties of the magnesium fluoride sols like viscosity, particle size distribution, and structural information are presented as well.

  5. Studies on the immune response and preparation of antibodies against a large panel of conjugated neurotransmitters and biogenic amines: specific polyclonal antibody response and tolerance.

    Science.gov (United States)

    Huisman, Han; Wynveen, Paul; Setter, Peter W

    2010-02-01

    We described the production and characterization of antibodies against three important groups of neuro-active haptens, e.g., neurotransmitters and biogenic amines. First, from the tryptophane metabolic pathway: tryptamine, serotonin, 5-hydroxy-indole acetic acid, and melatonin. Secondly, the tyrosine metabolic pathway: tyramine, dopamine, dihydroxyphenyl acetic acid, and norepinephrine. Thirdly, antibodies against excitatory and inhibitory neurotransmitters: glycine, glutamate, glutamine, and GABA. Immunogenic conjugates were prepared after linking haptens to carrier proteins. Most antibodies displayed high specificity against corresponding neuro-active haptens conjugated in vitro and in situ in biological specimens, but not to closely related conjugated metabolites, precursors, pharmaceuticals, agonists, antagonists, or free neuro-active haptens. Conjugated norepinephrine was highly tolerant in different animal species and produced incidentally a short specific antibody response.

  6. 码书自适应的大规模体数据矢量量化算法%A CODEBOOK ADAPTIVE VECTOR QUANTISATION ALGORITHM FOR LARGE SCALE VOLUME DATA

    Institute of Scientific and Technical Information of China (English)

    张强; 金义富

    2013-01-01

    针对大规模体数据矢量量化VQ(Vector Quantisation)编码时间长的问题,提出一种基于图形处理器的码书自适应的大规模体数据矢量量化算法.该算法首先提取原始体数据密度分布特征,据此选取合适的初始码书生成算法,将矢量数据分批先后载入图形处理器进行并行计算,每读入一批数据,根据该批数据的码准值对第一批数据产生的码书进行优化及扩充,随后完成该批数据的编码.实验结果表明,该算法提高了图像的编码速度及还原质量,明显缩短了图像的压缩时间,同时保证了体数据重构质量.%To solve the problem of time costing in encoding large scale volume data with vector quantisation method, we propose an algorithm of GPU-based adaptive codebook vector quantisation (ACVQ) for large scale volume data. The algorithm first extracts the density distribution feature of the original volume data, and hereby selects the appropriate initial codebook generation algorithm, then it loads the vector data into GPU successively by batch to carry out parallel computation. For each loading, we optimise and expand the first codebook generated by first batch according to the code reference of the data of that batch, followed by completing the data encoding of this batch. Experimental results suggest that ACVQ improves the encoding speed and the restored quality of image, evidently shorten the compression time of image, at the same time it ensures the reconstruction quality of volume data.

  7. Background culturable bacteria aerosol in two large public buildings using HVAC filters as long term, passive, high-volume air samplers.

    Science.gov (United States)

    Stanley, Nicholas J; Kuehn, Thomas H; Kim, Seung Won; Raynor, Peter C; Anantharaman, Senthilvelan; Ramakrishnan, M A; Goyal, Sagar M

    2008-04-01

    Background culturable bacteria aerosols were collected and identified in two large public buildings located in Minneapolis, Minnesota and Seattle, Washington over a period of 5 months and 3 months, respectively. The installed particulate air filters in the ventilation systems were used as the aerosol sampling devices at each location. Both pre and final filters were collected from four air handing units at each site to determine the influence of location within the building, time of year, geographical location and difference between indoor and outdoor air. Sections of each loaded filter were eluted with 10 ml of phosphate buffered saline (PBS). The resulting solutions were cultured on blood agar plates and incubated for 24 h at 36 degrees C. Various types of growth media were then used for subculturing, followed by categorization using a BioLog MicroStation (Biolog, Hayward, CA, USA) and manual observation. Environmental parameters were gathered near each filter by the embedded on-site environmental monitoring systems to determine the effect of temperature, humidity and air flow. Thirty nine different species of bacteria were identified, 17 found only in Minneapolis and 5 only in Seattle. The hardy spore-forming genus Bacillus was the most commonly identified and showed the highest concentrations. A significant decrease in the number of species and their concentration occurred in the Minneapolis air handling unit supplying 100% outdoor air in winter, however no significant correlations between bacteria concentration and environmental parameters were found.

  8. A Novel Way to Prepare TiO2 and γ-Al2O3 Supported Catalysts with Large Surface Areas

    Institute of Scientific and Technical Information of China (English)

    ZHU Yue-Xiang ZHU Yue-Xiang; ZHAO Bi-Ying; ZHOU Chang-Jun; WANG Rong-Qiu; XIE You-Chang

    2001-01-01

    pared by a novel way and characterized by X-ray diffractiou,Raman spectroscopy and BET surface area measurement.The results show: (1) all the samples,including M0O3/TiO2,WO3/TiO2, V2Os/TiO2, FeSO4/γ-Al2O3, Al2(SO4)3/γ-Al2O3,K2CO3/-Al2O3 and so on,prepared by impregnating TiO2·H20or pseudo-boehmite AlO(OH)with the active components them calcining at a high temperature exhibit much larger surface ar-eas than that of pure TiO2 or γ-Al2O3 calcined at the same tem-perature; (2) the surface area of the sample increases with the increase in the coverage of active component on the surface of the support; (3) when the content of active component reaches its utmost monolayer dispersion capacity, the surface area of the sample is the largest, and then decreases when the content of active component exceeds its dispersion threshold.

  9. Experimental evidence for negative turgor pressure in small leaf cells of Robinia pseudoacacia L versus large cells of Metasequoia glyptostroboides Hu et W.C.Cheng. 1. Evidence from pressure-volume curve analysis of dead tissue.

    Science.gov (United States)

    Yang, Dongmei; Pan, Shaoan; Ding, Yiting; Tyree, Melvin T

    2017-03-01

    This paper provides a mini-review of evidence for negative turgor pressure in leaf cells starting with experimental evidence in the late 1950s and ending with biomechanical models published in 2014. In the present study, biomechanical models were used to predict how negative turgor pressure might be manifested in dead tissue, and experiments were conducted to test the predictions. The main findings were as follows: (i) Tissues killed by heating to 60 or 80 °C or by freezing in liquid nitrogen all became equally leaky to cell sap solutes and all seemed to pass freely through the cell walls. (ii) Once cell sap solutes could freely pass the cell walls, the shape of pressure-volume curves was dramatically altered between living and dead cells. (iii) Pressure-volume curves of dead tissue seem to measure negative turgor defined as negative when inside minus outside pressure is negative. (iv) Robinia pseudoacacia leaves with small palisade cells had more negative turgor than Metasequoia glyptostroboides with large cells. (v) The absolute difference in negative turgor between R. pseudoacacia and M. glyptostroboides approached as much as 1.0 MPa in some cases. The differences in the manifestation of negative turgor in living versus dead tissue are discussed. © 2016 John Wiley & Sons Ltd.

  10. Extensive CO2 Leakage From Extinct and Modern CO2 Reservoirs in New Mexico and Arizona: Evaluating the Role of Seal Bypass and Large-Volume Travertine Deposition With Implications For CO2 Sequestration

    Science.gov (United States)

    Priewisch, A.; Crossey, L. J.; Karlstrom, K. E.; Mozley, P.

    2014-12-01

    Quaternary large-volume travertine deposits in New Mexico and Arizona occur along the Rio Grande rift and on the southeastern Colorado Plateau. Travertines are natural analogues for CO2 leakage along fault systems because they form due to the degassing of CO2 from carbonic groundwater that migrates up fault systems. Travertine volumes can be used to infer integrated CO2 leakage along faults, which includes: (1) CO2 that becomes fixed in CaCO3/travertine (tons of carbon converted into tons of carbonate), (2) the amount of CO2 that degassed into the atmosphere (twice the amount of (1), based on reaction stoichiometry), (3) dissolved CO2 that is carried away with the water discharging from a spring (based on modern spring discharge and dissolved carbon content), and (4) CO2 that escapes through the soil (based on modern soil flux measurements). The total CO2 leakage (1 and 2) calculated in this study is estimated as ~6 Gt (gigatons) whereas the integrated CO2 leakage (1-4) is estimated as ~128 Gt over ~450,000 years of travertine accumulation. U-series dating of the travertines shows that the deposits formed episodically which implies that CO2 leakage occurred episodically. Better understanding of integrated CO2 leakage along fault systems is needed to better constrain global estimates of natural CO2 fluxes, and to help in risk assessment of CO2 sequestration sites designed to effectively store anthropogenic CO2 in the subsurface.

  11. Large transport Jc in Sn-added SmFeAsO1-xFx tapes prepared by an ex situ PIT method

    Science.gov (United States)

    Wang, Chunlei; Yao, Chao; Lin, He; Zhang, Xianping; Zhang, Qianjun; Wang, Dongliang; Ma, Yanwei; Awaji, S.; Watanabe, K.; Tsuchiya, Y.; Sun, Y.; Tamegai, T.

    2013-07-01

    SmFeAsO1-xFx possesses the highest superconducting transition temperature (Tc) among the iron-based superconductors, with a very high upper critical field and critical current density (Jc). All these are desirable for practical applications. Although tremendous progress has been made in improving the Jc values for Sr(Ba)-122 tapes or wires [1-3], the transport Jc of Sm1111 tapes or wires is still very low. Here we report on large transport critical current densities observed in Sn-added SmFeAsO1-xFx/Fe tapes produced by an ex situ powder-in-tube (PIT) method. It was found that the loss of fluorine was reduced and the intergranular coupling was enhanced in the Sn-added samples. As a result, the onset and offset Tc values for 10 wt%, 20 wt% and 30 wt% Sn-added samples were 52 K and 35 K, 53 K and 39 K, and 54 K and 41.5 K, respectively. In particular, a transport Jc as large as 22 000 A cm-2 (Ic = 160 A) at 4.2 K under self-field was achieved in 30 wt% Sn-added specimens, which is the highest value reported so far for SmFeAsO1-xFx wires and tapes. Magneto-optical imaging further showed that there were large global currents over the whole sample, which is consistent with the results obtained by the four-probe method.

  12. The effects of inulin, dried Jerusalem artichoke tuber and a multispecies probiotic preparation on microbiota ecology and immune status of the large intestine in young pigs.

    Science.gov (United States)

    Barszcz, Marcin; Taciak, Marcin; Skomiał, Jacek

    2016-08-01

    The study aimed at determining the effect of two types of prebiotics and a multispecies probiotic on microbiota activity and composition, as well as mucosal immunity in the large intestine of young pigs. In total 48 piglets were divided into 6 groups (n = 8), which received from day 10 of life probiotic-unsupplemented (PU) or probiotic-supplemented (PS) diets. Probiotics were added at 0.5 g/kg diet and contained: Lactococcus lactis, Carnobacterium divergens, Lactobacillus casei, Lactobacillus plantarum and Saccharomyces cerevisiae. The PU and PS diets were formulated without prebiotic addition (control) or with addition of 2% of inulin from chicory root (IN) or 4% of dried Jerusalem artichoke tubers (DJA). After 40 days of feeding, digesta and tissue samples were taken from the caecum and three sections of the colon for analyses of microbiota activity and composition, secretory immunoglobulin A (sIgA) and intraepithelial lymphocytes (IEL). IN diets decreased the caecal digesta pH and β-glucosidase activity but increased propionic, valeric and total short chain fatty acid (SCFA) concentrations compared to control diets. Feeding DJA diets increased caecal valeric acid level, decreased the concentration of isoacids in the colon, reduced β-glucosidase and β-glucuronidase activity in the middle colon and increased Bifidobacterium spp. populations in the proximal and distal colon. PS diets increased the caecal acetic acid and total SCFA level, and Clostridium spp. populations in the distal colon. Neither probiotic nor prebiotics affected sIgA level or IEL number in the large intestine. In conclusion, DJA modified the microbiota ecology in the large intestine of young pigs to a greater extent than IN and the applied probiotic did not enhance effects of prebiotics.

  13. HOW MEDICAL UNDERGRADUATES PREPARE FOR UNIVERSITY EXAMINATION: LESSON FROM A TEACHING MEDICAL INSTITUTION IN SOUTH INDIA

    OpenAIRE

    Shib Sekhar Datta; Boratne, Abhijit V; Rajkumar Patil

    2013-01-01

    Background: Medical colleges in India conventionally follow a curriculum overfed with large volume of information expecting students will imbibe such curriculum unquestionably overlooking what and how they progress. There have been many attempts to improve the learning process of medical students, neglecting the process which students adopt towards such learning and prepare for their exams aiming better performance. Objective: To explore qualitatively the way medical undergraduates prepare ...

  14. 襄樊汉江三桥主墩承台大体积混凝土施工技术%Large Volume Concrete Construction Technology of Hanjiang the Third Bridge Main Pier Pile Cap in Xiangfan

    Institute of Scientific and Technical Information of China (English)

    吴刚; 蒲赞全; 钟启凯; 刘开扬

    2011-01-01

    Based on the large volume pile cap construction of Hanjiang the Third Bridge main pier in Xiangfan,the construction technology of the large volume pile cap is analyzed. , including cofferdam construction of steel sheet pile, bottom sealing of underwater concrete. A series of measures from concrete raw material to concrete pouring are taked to prevent exorbitant hydration temperature in mass concrete causing concrete crack, including mix design of low hydration heat concrete, temperature control calculation of concrete, field temperature control measures of mass concrete, temperature monitoring during construction. Thus,pile cap construction is completed successfully.%结合襄樊汉江三桥主墩大体积承台施工,分析了大体积承台施工技术,包括:钢板桩围堰施工,水下混凝土封底.为防止大体积混凝土在水化过程中结构内部产生过高的水化热温度,致使结构产生有害裂缝,从混凝土原材料到混凝土浇筑施工采取了一系列有效的技术控制措施,包括低水化热混凝土配合比设计、混凝土温控计算、大体积混凝土温度现场控制措施,以及施工过程中的温度监测,从而使得承台施工得以顺利完成.

  15. Correlation between tumour characteristics, SUV measurements, metabolic tumour volume, TLG and textural features assessed with {sup 18}F-FDG PET in a large cohort of oestrogen receptor-positive breast cancer patients

    Energy Technology Data Exchange (ETDEWEB)

    Lemarignier, Charles; Groheux, David [Saint-Louis Hospital, Assistance Publique - Hopitaux de Paris, Department of Nuclear Medicine, Paris (France); University Sorbonne Paris Cite, INSERM/CNRS UMR944/7212, Paris (France); Martineau, Antoine; Vercellino, Laetitia; Merlet, Pascal [Saint-Louis Hospital, Assistance Publique - Hopitaux de Paris, Department of Nuclear Medicine, Paris (France); Teixeira, Luis; Espie, Marc [Saint-Louis Hospital, Breast Diseases Unit, Paris (France); University Sorbonne Paris Cite, INSERM/CNRS UMR944/7212, Paris (France)

    2017-07-15

    The study was designed to evaluate 1) the relationship between PET image textural features (TFs) and SUVs, metabolic tumour volume (MTV), total lesion glycolysis (TLG) and tumour characteristics in a large prospective and homogenous cohort of oestrogen receptor-positive (ER+) breast cancer (BC) patients, and 2) the capability of those parameters to predict response to neoadjuvant chemotherapy (NAC). 171 consecutive patients with large or locally advanced ER+ BC without distant metastases underwent an {sup 18}F-FDG PET examination before NAC. The primary tumour was delineated with an adaptive threshold segmentation method. Parameters of volume, intensity and texture (entropy, homogeneity, contrast and energy) were measured and compared with tumour characteristics determined on pre-treatment breast biopsy (Wilcoxon rank-sum test). The correlation between PET-derived parameters was determined using Spearman's coefficient. The relationship between PET features and pathological findings was determined using the Wilcoxon rank-sum test. Spearman's coefficients between SUV{sub max} and TFs were 0.43, 0.24, -0.43 and -0.15 respectively for entropy, homogeneity, energy and contrast; they were higher between MTV and TFs: 0.99, 0.86, -0.99 and -0.87. All TFs showed a significant association with the histological type (IDC vs. ILC; 0.02 < P < 0.03) but didn't with immunohistochemical characteristics. SUV{sub max} and TLG predicted the pathological response (P = 0.0021 and P = 0.02 respectively); TFs didn't (P: 0.27, 0.19, 0.94, 0.19 respectively for entropy, homogeneity, energy and contrast). The correlation of TFs was poor with SUV parameters and high with MTV. TFs showed a significant association with the histological type. Finally, while SUV{sub max} and TLG were able to predict response to NAC, TFs failed. (orig.)

  16. Volume regulation in epithelia

    DEFF Research Database (Denmark)

    Larsen, Erik Hviid; Hoffmann, Else Kay

    2016-01-01

    function of iso-osmotic fluid transport that depends on Na+ recirculation. The causative relationship is discussed for a fluid-absorbing and a fluid-secreting epithelium of which the Na+ recirculation mechanisms have been identified. A large number of transporters and ion channels involved in cell volume...... regulation are cloned. The volume-regulated anion channel (VRAC) exhibiting specific electrophysiological characteristics seems exclusive to serve cell volume regulation. This is contrary to K+ channels as well as cotransporters and exchange mechanisms that may serve both transepithelial transport and cell...

  17. Small-Volume Injections: Evaluation of Volume Administration Deviation From Intended Injection Volumes.

    Science.gov (United States)

    Muffly, Matthew K; Chen, Michael I; Claure, Rebecca E; Drover, David R; Efron, Bradley; Fitch, William L; Hammer, Gregory B

    2017-10-01

    In the perioperative period, anesthesiologists and postanesthesia care unit (PACU) nurses routinely prepare and administer small-volume IV injections, yet the accuracy of delivered medication volumes in this setting has not been described. In this ex vivo study, we sought to characterize the degree to which small-volume injections (≤0.5 mL) deviated from the intended injection volumes among a group of pediatric anesthesiologists and pediatric postanesthesia care unit (PACU) nurses. We hypothesized that as the intended injection volumes decreased, the deviation from those intended injection volumes would increase. Ten attending pediatric anesthesiologists and 10 pediatric PACU nurses each performed a series of 10 injections into a simulated patient IV setup. Practitioners used separate 1-mL tuberculin syringes with removable 18-gauge needles (Becton-Dickinson & Company, Franklin Lakes, NJ) to aspirate 5 different volumes (0.025, 0.05, 0.1, 0.25, and 0.5 mL) of 0.25 mM Lucifer Yellow (LY) fluorescent dye constituted in saline (Sigma Aldrich, St. Louis, MO) from a rubber-stoppered vial. Each participant then injected the specified volume of LY fluorescent dye via a 3-way stopcock into IV tubing with free-flowing 0.9% sodium chloride (10 mL/min). The injected volume of LY fluorescent dye and 0.9% sodium chloride then drained into a collection vial for laboratory analysis. Microplate fluorescence wavelength detection (Infinite M1000; Tecan, Mannedorf, Switzerland) was used to measure the fluorescence of the collected fluid. Administered injection volumes were calculated based on the fluorescence of the collected fluid using a calibration curve of known LY volumes and associated fluorescence.To determine whether deviation of the administered volumes from the intended injection volumes increased at lower injection volumes, we compared the proportional injection volume error (loge [administered volume/intended volume]) for each of the 5 injection volumes using a linear

  18. 大尺寸触控面板用铜布线薄膜的制备%Preparation of copper wiring film for large-size touch panel

    Institute of Scientific and Technical Information of China (English)

    曾海军

    2014-01-01

    介绍了一种高透光、电阻小,可用于触摸面板大型化的透明导电性薄膜的制造工艺,即在 PET(聚对苯二甲酸乙二酯)薄膜上形成肉眼不可见的铜网。其工艺流程主要包括低温等离子体表面清洗,磁控溅射Ni-Cr过渡层及Cu植晶层,硫酸盐镀铜层,光刻。所得铜布线薄膜的性能超过了一般ITO(氧化铟锡)膜的性能。%A method for producing a transparent and conductive film with high light transmission and low resistance used in large-size touch panel was introduced. Copper mesh which is invisible to the eyes is formed on a PET thin film by the following steps:(1) cleaning the surface with low-temperature plasma;(2) magnetron sputtering with Ni-Cr intermediate layer and Cu seed layer; (3) electroplating Cu in a sulfate bath;and (4) photolithography. The copper wiring film obtained has superior performance than a common ITO film.

  19. Determination of PCDD/Fs in food samples using programmable temperature vaporizer-based large volume injection by high resolution gas chromatography-high resolution mass spectrometry%程序升温大体积进样在HRGC-HRMS法测定食品中PCDD/F的应用

    Institute of Scientific and Technical Information of China (English)

    张磊; 李敬光; 赵云峰; 吴永宁

    2014-01-01

    Objective By optimizing critical parameters of programmable temperature vaporizer (PTV), a method of PTV-based large volume injection was established for the determination of PCDD/Fs in various food samples using HRGC-HRMS. Methods The preparation of food, including extraction, clean-up, separation and concentration, was carried out depending on GB/T5009.205-2007 “Determination of Toxic Equivalencies of Dioxin and Dioxin-like Compounds in Foods”. The injection volume of extracts was 15μL, and the analyte was subsequently determined by using HRGC-HRMS with isotopic dilution. Results The optimized parame-ter of the initial temperature of PTV injector, the temperature of evaporation phase, and the flow rate of evapo-ration phase was set at 115℃, 140℃, and 5 mL/min, respectively. Peak area and the ratio of signal to noise (S/N) of PCDD/F congeners significantly increased using PTV-based large volume injection (P<0.05). Conclu-sion The method of PTV-based large volume injection can notably raise the competence of determining PCDD/Fs in food, which may help to assess the food safety risk more accurately and reliably.%目的:通过优化程序升温蒸发进样口的相关参数,噁建立测定食品中多氯代二苯并二英和多氯代二苯并呋喃(PCDD/Fs)的程序升温大体积进样高分辨气相色谱-高分辨质谱(HRGC-HRMS)方法。方法食品样品提取、净化分离和浓缩按《GB/T 5009.205-2007噁食品中二英及其类似物毒性当量的测定》规定进行,待测试样进样15μL,应用HRGC-HRMS结合同位素稀释技术测定其中PCDD/Fs。结果最佳条件为进样口初始温度115℃,蒸发相温度140℃,蒸发相吹扫流速为5 mL。大体积进样所获得的待测物峰面积及S/N存在显著增加(P<0.05)。结论程序升温大体积进样方式能显著提高食品基质中PCDD/Fs的检测能力,有助于保证食品安全风险评估结果的准确可靠。

  20. ISABELLE. Volume 3. Experimental areas, large detectors

    Energy Technology Data Exchange (ETDEWEB)

    1981-01-01

    This section presents the papers which resulted from work in the Experimental Areas portion of the Workshop. The immediate task of the group was to address three topics. The topics were dictated by the present state of ISABELLE experimental areas construction, the possibility of a phased ISABELLE and trends in physics and detectors.

  1. Effect of first oral magnesium sulphate volume on intestinal preparation%口服硫酸镁首次饮水量对肠道准备的影响

    Institute of Scientific and Technical Information of China (English)

    万雪英

    2012-01-01

    Objective To study the effect of first oral magnesium sulphate volume on intestinal preparation and satisfaction of patients. Methods Four hundred and fourteen patients were randomly divided into control group(group 1), convention groups 2 and 3(138 in each group). Patients in control group were given 70ml 50% magnesium sulfate immediately after taking 300ml water in 5 minutes. The patients were then given the remaining 1 200ml water after the first defecation and took a fast walk each time after drinking water. They could massage their abdomen on bed when they felt tired. Patients in convention groups 2 and 3 received 500ml and 800ml water, respectively. The drinking time and volume of water and walking after drinking water were similar to those in control group. Results The intestinal cleanliness was better and the adverse reactions were less in convention group 3 than in convention group 2 and control group(P<0.05). Conclusion Drinking 800ml water after taking 70ml magnesium sulfate can shorten the intestinal preparation time and reduce the adverse reactions.%目的 探索口服硫酸镁后首次饮水量对肠道准备效果和患者满意度的影响.方法 按数字表法将研究对象随机分为3组,每组138例.组1为对照组,组2、组3为干预组.组1按传统方法服用硫酸镁,即口服50%硫酸镁溶液70ml后立即服用清水300ml,要求5min内饮完.待首次排便后再分次饮用余下清水.饮水总量共计约1500ml.指导患者于每次喝水后进行快走运动,疲劳时可卧床进行腹部按摩;组2、组3为干预组,采用改良方法服用硫酸镁.首次饮水量分别改为500ml及800ml.饮水时间、总饮水量及饮水后运动指导均同对照组.结果 组3肠道清洁度优于组1、组2,且不良反应较少,差异有统计学意义(P<0.05).结论 口服硫酸镁后首次饮水800ml既可缩短肠道准备时间又可减少不良反应发生.

  2. New method for rapid solid-phase extraction of large-volume water samples and its application to non-target screening of North Sea water for organic contaminants by gas chromatography-mass spectrometry.

    Science.gov (United States)

    Weigel, S; Bester, K; Hühnerfuss, H

    2001-03-30

    A method has been developed that allows the solid-phase extraction of microorganic compounds from large volumes of water (10 l) for non-target analysis of filtered seawater. The filtration-extraction system is operated with glass fibre filter candles and the polymeric styrene-divinylbenzene sorbent SDB-1 at flow-rates as high as 500 ml/min. Recovery studies carried out for a couple of model substances covering a wide range of polarity and chemical classes revealed a good performance of the method. Especially for polar compounds (log Kow 3.3-0.7) quantitative recovery was achieved. Limits of detection were between 0.1 and 0.7 ng/l in the full scan mode of the MS. The suitability of the method for the analysis of marine water samples is demonstrated by the non-target screening of water from the German Bight for the presence of organic contaminants. In the course of this screening a large variety of substances was identified including pesticides, industrial chemicals and pharmaceuticals. For some of the identified compounds their occurrence in marine ecosystems has not been reported before, such as dichloropyridines, carbamazepine, propyphenazone and caffeine.

  3. Using Large-scale Spatially and Temporally Consistent Reanalysis Data to Assess Fire Weather and Fire Regimes in Siberia in Preparation for Future Fire Weather Prediction

    Science.gov (United States)

    Soja, A. J.; Westberg, D. J.; Stackhouse, P. W.; McRae, D.; Jin, J.

    2008-12-01

    A primary driving force of land cover change in boreal regions is fire, where extreme fire seasons are influenced by local weather and ultimately climate. It is predicted that fire frequency, area burned, fire severity, fire season length, and severe fire seasons will increase under current climate change scenarios. The use of local ground based weather data can be used to gauge the local fire potential on a daily, monthly, or seasonal basis. However, the number and distribution of surface observing stations in Siberia have been declining since the early 1990's. A compounding problem is existing observing stations have missing data on various time scales. The density of stations is limited; hence results may not be representative of the spatial reality. One solution is the temporally and spatially consistent NASA Goddard Earth Observing System version 4 (GEOS-4) satellite-derived weather data interpolated to a 1x1 degree grid. In previous work, we showed the Canadian Forest Fire Weather Index (FWI) derived using GEOS-4 weather and Global Precipitation Climatology Project (GPCP) precipitation data compared well to ground based weather data from Jakutsk (Sakha) and Kyzyl (Tuva), Russia. Our primary focus is to expand on this work by spatially comparing the FWI derived from GEOS-4 / GPCP data and ground-based weather observations from the National Climatic Data Center (NCDC). Extreme fires burned in Sakha and Tuva in 2002 and 2004, respectively, while in contrast, normal fire seasons occurred in Sakha and Tuva in 1999 and 2002, respectively. For this reason, we focus on the 1999, 2002, and 2004 fire seasons (April - September). In this investigation, we demonstrate how fire weather models perform on a large scale and investigate the performance of these models relative to input uncertainties. We intend to use this information to build regional-scale fire predictions systems that can be used for future interactive fire-weather-climate assessments.

  4. Variance-based Sensitivity Analysis of Large-scale Hydrological Model to Prepare an Ensemble-based SWOT-like Data Assimilation Experiments

    Science.gov (United States)

    Emery, C. M.; Biancamaria, S.; Boone, A. A.; Ricci, S. M.; Garambois, P. A.; Decharme, B.; Rochoux, M. C.

    2015-12-01

    Land Surface Models (LSM) coupled with River Routing schemes (RRM), are used in Global Climate Models (GCM) to simulate the continental part of the water cycle. They are key component of GCM as they provide boundary conditions to atmospheric and oceanic models. However, at global scale, errors arise mainly from simplified physics, atmospheric forcing, and input parameters. More particularly, those used in RRM, such as river width, depth and friction coefficients, are difficult to calibrate and are mostly derived from geomorphologic relationships, which may not always be realistic. In situ measurements are then used to calibrate these relationships and validate the model, but global in situ data are very sparse. Additionally, due to the lack of existing global river geomorphology database and accurate forcing, models are run at coarse resolution. This is typically the case of the ISBA-TRIP model used in this study.A complementary alternative to in-situ data are satellite observations. In this regard, the Surface Water and Ocean Topography (SWOT) satellite mission, jointly developed by NASA/CNES/CSA/UKSA and scheduled for launch around 2020, should be very valuable to calibrate RRM parameters. It will provide maps of water surface elevation for rivers wider than 100 meters over continental surfaces in between 78°S and 78°N and also direct observation of river geomorphological parameters such as width ans slope.Yet, before assimilating such kind of data, it is needed to analyze RRM temporal sensitivity to time-constant parameters. This study presents such analysis over large river basins for the TRIP RRM. Model output uncertainty, represented by unconditional variance, is decomposed into ordered contribution from each parameter. Doing a time-dependent analysis allows then to identify to which parameters modeled water level and discharge are the most sensitive along a hydrological year. The results show that local parameters directly impact water levels, while

  5. Selective determination of estrogenic compounds in water by microextraction by packed sorbents and a molecularly imprinted polymer coupled with large volume injection-in-port-derivatization gas chromatography-mass spectrometry.

    Science.gov (United States)

    Prieto, A; Vallejo, A; Zuloaga, O; Paschke, A; Sellergen, B; Schillinger, E; Schrader, S; Möder, M

    2011-10-03

    A fully automated protocol consisting of microextraction by packed sorbents (MEPS) coupled with large volume injection-in-port-derivatization-gas chromatography-mass spectrometry (LVI-derivatization-GC-MS) was developed to determine endocrine disrupting compounds (EDCs) such as alkylphenols, bisphenol A, and natural and synthetic hormons in river and waste water samples. During method optimization, the extraction parameters as ion strength of the water sample, the MEPS extraction regime, the volume of organic solvent used for the elution/injection step, the type of elution solvents and the selectivity of the sorbents were studied. For optimum in-port-derivatization, 10 μL of the derivatization reagent N,O-bis(trimethylsilyl)triufloroacetamide with 1% of trimethylchlorosilane (BSTFA+1% TMCS) was used. 17β-Estradiol-molecularly imprinted polymer (MIP) and silica gel (modified with C-18) sorbents were examined for the enrichment of the target analytes from water samples and the obtained results revealed the high selectivity of the MIP material for extraction of substances with estrogen-like structures. Recovery values for most of the analytes ranged from 75 to 109% for the C18 sorbent and from 81 to 103% for the MIP material except for equilin (on C18 with only 57-66% recovery). Precision (n=4) of the entire analysis protocol ranged between 4% and 22% with both sorbents. Limits of detection (LODs) were at the low ngL(-1) level (0.02-87, C18 and 1.3-22, MIP) for the target analytes.

  6. Alternative sample preparation methods for MALDI-MS

    Energy Technology Data Exchange (ETDEWEB)

    Hurst, G.B.; Buchanan, M.V. [Oak Ridge National Lab., TN (United States); Czartoski, T.J. [Kenyon College, Gambier, OH (United States)

    1994-12-31

    Since the introduction of matrix-assisted laser desorption and ionization (MALDI), sample preparation has been a limiting step in the applicability of this important technique for mass spectrometric analysis of biomolecules. A number of variations on the original sample preparation method for have been described. The {open_quotes}standard{close_quotes} method of MALDI sample preparation requires mixing a solution containing the analyte and a large excess of matrix, and allowing a small volume of this solution to dry on a probe tip before insertion into the mass spectrometer. The resulting sample can fairly inhomogeneous. As a result, the process of aiming the desorption laser at a favorable spot on the dried sample can be tedious and time-consuming. The authors are evaluating several approaches to MALDI sample preparation, with the goal of developing a faster and more reproducible method.

  7. LLE review. Quarterly report, January 1994--March 1994, Volume 58

    Energy Technology Data Exchange (ETDEWEB)

    Simon, A. [ed.

    1994-07-01

    This volume of the LLE Review, covering the period Jan - Mar 1994, contains articles on backlighting diagnostics; the effect of electron collisions on ion-acoustic waves and heat flow; using PIC code simulations for analysis of ultrashort laser pulses interacting with solid targets; creating a new instrument for characterizing thick cryogenic layers; and a description of a large-aperture ring amplifier for laser-fusion drivers. Three of these articles - backlighting diagnostics; characterizing thick cryogenic layers; and large-aperture ring amplifier - are directly related to the OMEGA Upgrade, now under construction. Separate abstracts have been prepared for articles from this report.

  8. Preparation and characterization of mesoporous indium oxide

    Institute of Scientific and Technical Information of China (English)

    ZHAO Yi-zhe; CHENG Zhi-xuan; PAN Qing-yi; DONG Xiao-wen; ZHANG Jian-cheng; PAN Ling-li

    2009-01-01

    Indium oxide nanocrystals with mesoporous structure were successfully synthesized by using triblock copolymer as a template,and characterized by thermogravimetry-differential scanning calorimeter (TG-DSC),X-ray powder diffraction (XRD),high resolution transmission electron microscopy (HRTEM) and N2 adsorption.A high EO/PO ratio is thought to be the key point to prepare mesoporous In2O3.The results show that the average pore diameter of the products is 6 nm,the BET surface area is 54.78 m2/g,and the adsorbing pore volume is 0.345 cm3/g.After comparing with normal indium oxide nanoparticles by BET test,mesoporous indium oxide demonstrates a large difference in adsorbing pore volume and average pore diameters from normal ones.

  9. Moduli stabilization, large-volume dS minimum without D3{sup -bar} -branes, (non-)supersymmetric black hole attractors and two-parameter Swiss cheese Calabi-Yau's

    Energy Technology Data Exchange (ETDEWEB)

    Misra, Aalok [Department of Physics, Indian Institute of Technology, Roorkee 247 667, Uttaranchal (India); Physics Department, Theory Unit, CERN, CH-1211 Geneva 23 (Switzerland)], E-mail: aalokfph@iitr.ernet.in; Shukla, Pramod [Department of Physics, Indian Institute of Technology, Roorkee 247 667, Uttaranchal (India)], E-mail: pmathdph@iitr.ernet.in

    2008-08-11

    We consider two sets of issues in this paper. The first has to do with moduli stabilization, existence of 'area codes' [A. Giryavets, New attractors and area codes, JHEP 0603 (2006) 020, (hep-th/0511215)] and the possibility of getting a non-supersymmetric dS minimum without the addition of D3-bar-branes as in KKLT for type II flux compactifications. The second has to do with the 'inverse problem' [K. Saraikin, C. Vafa, Non-supersymmetric black holes and topological strings, (hep-th/0703214)] and 'fake superpotentials' [A. Ceresole, G. Dall'Agata, Flow equations for non-BPS extremal black holes, JHEP 0703 (2007) 110, (hep-th/0702088)] for extremal (non-)supersymmetric black holes in type II compactifications. We use (orientifold of) a 'Swiss cheese' Calabi-Yau [J.P. Conlon, F. Quevedo, K. Suruliz, Large-volume flux compactifications: Moduli spectrum and D3/D7 soft supersymmetry breaking, JHEP 0508 (2005) 007, (hep-th/0505076)] expressed as a degree-18 hypersurface in WCP{sup 4}[1,1,1,6,9] in the 'large-volume-scenario' limit [V. Balasubramanian, P. Berglund, J.P. Conlon, F. Quevedo, Systematics of moduli stabilisation in Calabi-Yau flux compactifications, JHEP 0503 (2005) 007, (hep-th/0502058)]. The main result of our paper is that we show that by including non-perturbative {alpha}{sup '} and instanton corrections in the Kaehler potential and superpotential [T.W. Grimm, Non-perturbative corrections and modularity in N=1 type IIB compactifications, (arXiv: 0705.3253 [hep-th])], it may be possible to obtain a large-volume non-supersymmetric dS minimum without the addition of anti-D3 branes a la KKLT. The chosen Calabi-Yau has been of relevance also from the point of other studies of Kaehler moduli stabilization via non-perturbative instanton contributions [F. Denef, M.R. Douglas, B. Florea, Building a better racetrack, JHEP 0406 (2004) 034, (hep-th/0404257)] and non-supersymmetric AdS vacua (and their

  10. The evolution of bowel preparation and new developments.

    Science.gov (United States)

    Park, Jeong Bae; Lee, Yong Kook; Yang, Chang Heon

    2014-05-01

    Bowel preparation is essential for successful colonoscopy examination, and the most important factor is the bowel preparation agent used. However, selection of a bowel preparation agent invariably involves compromise. Originally, bowel preparation was performed for radiologic and surgical purposes, when the process involved dietary limitations, cathartics, and enemas, which had many side effects. Development of polyethylene glycol (PEG) solution led to substantive advancement of bowel preparation; however, despite its effectiveness and safety, the large volume involved, and its salty taste and unpleasant odor reduce compliance. Accordingly, modified PEG solutions requiring consumption of lower volumes and sulfate-free solutions were developed. Aqueous sodium phosphate is more effective and better tolerated than PEG solutions; however, fatal complications have occurred due to water and electrolyte shifts. Therefore, aqueous sodium phosphate was withdrawn by the US Food and Drug Administration, and currently, only sodium phosphate tablets remain available. In addition, oral sulfate solution and sodium picosulfate/magnesium citrate are also available, and various studies have reported on adjunctive preparations, such as hyperosmolar or stimulant laxatives, antiemetics, and prokinetics, which are now in various stages of development.

  11. Platelet-rich preparations to improve healing. Part I: workable options for every size practice.

    Science.gov (United States)

    Davis, Vicki L; Abukabda, Alaeddin B; Radio, Nicholas M; Witt-Enderby, Paula A; Clafshenkel, William P; Cairone, J Vito; Rutkowski, James L

    2014-08-01

    Numerous studies have demonstrated that platelet-rich preparations applied to surgical sites, injuries, or wounds are a safe and effective way to promote soft tissue healing and bone growth. Various protocols have been developed for preparing platelet-rich preparations, with subtle but important differences between them. Unfortunately, only a minority of clinicians use platelet-rich preparations, such as platelet-rich plasma and platelet-rich fibrin, in their practice, possibly due to confusion about the different methods and their advantages and disadvantages. Therefore, the different types of preparations are described to help guide the selection of the best method for any size practice. Classic methods generally require large volumes of blood and can be expensive, complicated, and time-intensive. Simpler protocols have been developed recently, which require relatively inexpensive equipment and small blood volumes and, thus, may be more applicable for small clinical practices. Platelet-rich preparations accelerate healing at earlier time points to reduce discomfort and the potential for adverse outcomes, including infection, poor wound closure, and delays in forming strong bone for subsequent procedures (such as implants). However, platelet-rich preparations may also improve long-term outcomes in patients expected to have impaired healing, such as with lifestyle choices (eg, smoking), medications (eg, steroids), diseases (eg, diabetes, osteoporosis, atherosclerosis), and aging, by supplementing the deficient wound environment to restore proper healing. Therefore, both large and small clinical practices would benefit from utilizing platelet-rich preparations to enhance healing in their patients.

  12. The preparation of a new type of ferrocene-based compounds with large conjugated system containing symmetrical aromatic vinyl with Schiff base moieties and the study of their third-order nonlinear optical properties

    Science.gov (United States)

    Yu, Weiguo; Jia, Jianhong; Gao, Jianrong; Han, Liang; Li, Yujin

    2016-09-01

    Herein we reported the preparation of a new type of ferrocene-based compounds with large conjugated system containing symmetrical aromatic vinyl and Schiff base moieties and the study of their third-order nonlinear optical (NLO) properties. Their third-order NLO properties were measured using femtosecond laser and degenerate four-wave mixing (DFWM) technique. The obtained χ(3), n2 and γ values of these molecules were found in the range of 0.998-1.429 × 10-12 esu,1.847-2.646 × 10-11 esu and 1.026-1.449 × 10-30 esu, respectively. The response time ranged from 43.65 fs to 61.71 fs. The results indicate that these compounds have potential nonlinear optical applications.

  13. Large tunneling anisotropic magnetoresistance in La0.7Sr0.3MnO3/pentacene/Cu structures prepared on SrTiO3 (110) substrates

    Science.gov (United States)

    Kamiya, Takeshi; Miyahara, Chihiro; Tada, Hirokazu

    2017-01-01

    We investigated tunneling anisotropic magnetoresistance (TAMR) at the interface between pentacene and La0.7Sr0.3MnO3 (LSMO) thin films prepared on SrTiO3 (STO) (110) substrates. The dependence of the TAMR ratio on the magnetic field strength was approximately ten times larger than that of the magnetic field angle at a high magnetic field. This large difference in the TAMR ratio is explained by the interface magnetic anisotropy of strain-induced LSMO thin films on a STO (110) substrate, which has an easy axis with an out-of-plane component. We also note that the TAMR owing to out-of-plane magnetization was positive at each angle of the in-plane magnetic field. This result implies that active control of the interface magnetic anisotropy between organic materials and ferromagnetic metals should realize nonvolatile and high-efficiency TAMR devices.

  14. 山东省男子体操队体育信息服务实践研究%Information services for Shandong gymnastics team preparing for large -scale sporting events

    Institute of Scientific and Technical Information of China (English)

    满晓霞

    2015-01-01

    依据山东省男子体操队伦敦奥运会竞技备战周期的项目布局及夺金任务目标,采用教练访谈、文献资料、实地调研、数理统计等多种方式,为山东省男子体操队开展全方位体育信息咨询服务,涉及运动训练信息、对手情报信息、参赛环境情报等诸多方面。一方面,在备战大型综合性运动会中进行了体育信息服务模式的积极探索;另一方面,也为管理部门及教练员、运动员科学备战参赛提供信息依据和智力支持。%In preparation for large -scale sporting events,sports information service is of much help for sports authorities to make macro strategies and develop scientific decisions.The Olympic Games is a typical representative of large -scale sporting events.Therefore,taking Shandong Province preparing for the London Olympics as an example,with the methods of literature review,interviews with experts,investigation teams,video analysis,statistics and so on,the paper discussed how the information were gathered,processed and transmitted,and explored its application benefits.

  15. Optimisation of a selective method for the determination of organophosphorous triesters in outdoor particulate samples by pressurised liquid extraction and large-volume injection gas chromatography-positive chemical ionisation-tandem mass spectrometry.

    Science.gov (United States)

    Quintana, José Benito; Rodil, Rosario; López-Mahía, Purificación; Muniategui-Lorenzo, Soledad; Prada-Rodríguez, Darío

    2007-07-01

    A selective analytical method for the determination of nine organophosphate triesters and triphenylphosphine oxide (TPPO) in outdoor particulate matter is presented. It involves a fully automated pressurised liquid extraction (PLE) step, integrating an alumina clean-up process, and subsequent determination by large-volume injection gas chromatography-positive chemical ionisation-tandem mass spectrometry (LVI-GC-PCI-MS/MS). The extraction variables (solvent, amount of adsorbent, temperature, time and number of cycles) were optimised using a multicriteria strategy which implements a desirability function that maximises both extraction and clean-up efficiencies while searching for the best-compromise PLE conditions. The final method affords quantification limits of between 0.01 and 0.3 microg g(-1) and recoveries of >80%, with the exceptions of the most polar analytes, TCEP and TPPO (~65%) for both urban dust and PM10 samples. Moreover, the method permitted the levels of these compounds in dust deposited outdoors (between LOD and 0.5 microg g(-1) for TEHP) and PM10 samples (between LOD and 2.4 microg m(-3) for TiBP) to be measured and reported for the first time.

  16. A comparative study of diode laser and plasmakinetic in transurethral enucleation of the prostate for treating large volume benign prostatic hyperplasia: a randomized clinical trial with 12-month follow-up.

    Science.gov (United States)

    Wu, Gang; Hong, Zhe; Li, Chao; Bian, Cuidong; Huang, Shengsong; Wu, Denglong

    2016-05-01

    The objective of this study is to compare the efficacy and safety of diode laser enucleation of the prostate (DiLEP) with plasmakinetic enucleation of the prostate (PKEP) for symptomatic benign prostatic hyperplasia (BPH) patients with large prostate (volume > 80 ml). From January 2013 to June 2014, 80 consecutive patients were randomized treated with DiLEP (n = 40) or PKEP (n = 40). Perioperative and postoperative outcome data were assessed during a 1-year follow-up. There were no significant preoperative differences between the two surgical groups. The mean prostate volumes in the DiLEP and PKEP groups were 98.6 and 93.3 ml, respectively. DiLEP was equivalent to PKEP in improvement in International Prostate Symptom Score (IPSS), quality of life scores, and maximum flow rate. Compared with PKEP, patients treated with DiLEP showed a lower risk of blood loss (P prostates (volume > 80 ml). Compared with PKEP, DiLEP provides a decreased risk of hemorrhage, reduced bladder irrigation, and catheterization times, as well as shorter hospital stays.

  17. Development of a solid-phase extraction system modified for preconcentration of emerging contaminants in large sample volumes from rivers of the lagoon system in the city of Rio de Janeiro, Brazil.

    Science.gov (United States)

    Lopes, Vitor Sergio Almeida; Riente, Roselene Ribeiro; da Silva, Alexsandro Araújo; Torquilho, Delma Falcão; Carreira, Renato da Silva; Marques, Mônica Regina da Costa

    2016-09-15

    A single method modified for monitoring of emerging contaminants in river water was developed for large sample volumes. Water samples from rivers of the lagoon system in the city of Rio de Janeiro (Brazil) were analyzed by the SPE-HPLC-MS-TOF analytical method. Acetaminophen was detected in four rivers in the concentration range of 0.09μgL(-1) to 0.14μgL(-1). Salicylic acid was also found in the four rivers in the concentration range of 1.65μgL(-1) to 4.81μgL(-1). Bisphenol-A was detected in all rivers in the concentration range of 1.37μgL(-1) to 39.86μgL(-1). Diclofenac was found in only one river, with concentration of 0.22μgL(-1). The levels of emerging organic pollutants in the water samples of the Jacarepaguá hydrographical basin are significant. The compounds are not routinely monitored and present potential risks to environmental health.

  18. The preparation of the poly(vinyl alcohol/graphene nanocomposites with low percolation threshold and high electrical conductivity by using the large-area reduced graphene oxide sheets

    Directory of Open Access Journals (Sweden)

    Q. Fu

    2013-09-01

    Full Text Available We report a method to prepare the poly(vinyl alcohol/reduced graphene oxide (PVA/rGO nanocomposites with low percolation threshold and high electrical conductivity by using the large-area reduced graphene oxide (LrGO sheets. The large-area graphene oxide (LGO sheets are expected to overlap better with each other and form the continuous GO network in PVA matrix than small-area graphene oxide (SGO. During the thermal reduction process, the LGO sheets are easily restored and improve the electrical conductivity of nanocomposites due to their low damage level of conjugate-structure. As a result, the percolation threshold of PVA/LrGO nanocomposites is ~0.189 wt% lower than present reports (0.5~0.7 wt%. At the LrGO content of 0.7 wt%, the electrical conductivity of PVA/LrGO nanocomposites reaches 6.3•10–3 S/m. Besides that, this method only takes 15~30 min to reduce the PVA/GO nanocomposites effectively.

  19. Hydration Heat Analysis of MIDAS/FEA:Taking the Large Volume Concrete Pile Caps of the Extra Large Bridge of Linghe in Kedi Dam for Example%MIDAS/FEA的水化热分析--以克地坝陵河特大桥大体积混凝土承台为例

    Institute of Scientific and Technical Information of China (English)

    刘海涛

    2015-01-01

    The large volume concrete is widely used in the construction of pile caps. In order to solve the heat of hydration in the construction, this paper takes 3# pile cap of the main pier continuous beam of the large bridge of Linghe in Kedi dam for example, and uses the finite element analysis software of MIDAS/FEA to analyze the heat of hydration effect of the pile cap. According to the measured data of MIDAS/FEA, the related policy suggestions are put forward to provide references for the similar engineering construction and implement the management of value engineering.%在承台施工中,大体积混凝土得到广泛使用。为了解决施工中出现的水化热问题,本文以克地坝陵河特大桥连续梁主墩3#承台为例,采用MIDAS/FEA有限元分析软件对该承台的水化热效果进行分析,并根据MIDAS/FEA测得的相关数据,同时提出相应的政策建议,为同类工程施工提供参考依据,进而实现价值工程管理的目的。

  20. Preparation of chitosan gel

    Directory of Open Access Journals (Sweden)

    Lagerge S.

    2012-06-01

    Full Text Available Aerogel conditioning of the chitosan makes it possible to prepare porous solids of significant specific surface. The increase in the chitosan concentration or the degree of acetylation decreases the specific surface of the synthesized chitosan gel. Whereas drying with supercritical CO2 more effectively makes it possible to preserve the volume of the spheres of gel and to have a more significant specific surface in comparison with evaporative drying.

  1. Thirty two cases of large volume liposuction using Water Jet-Assisted Liposuction instrument%全身大容量水射流辅助吸脂32例

    Institute of Scientific and Technical Information of China (English)

    石成方; 谷廷敏; 李蠡; 赵志力; 隋志甫; 常冬青

    2011-01-01

    Objective To estimate the clinical effect and safety of large volume Water Jet-Assisted Liposucticm (WAL). Metiwds Thirty two cases with 139 positions underwent WAL. Indexes such as the time for liposuction, the quantity of swelling liquid, rinse solution, aspirate and fet, ;ind the duration of postoperative pain were recorded The color of aspirate, intraoperatjve and postoperative vital signs of patients, degree of skin eccbymosis and edema, planeness of skin, toxic reaction of lidocaine and other complications were collected and used to estimate the superiority of WAL. Results In the series of 32 patients, die average time for liposuction was 4.5 hours; the average quantity of swellingliquid was IS50ml,rinse solution 15760ml,aspiratc ll480ml,fat 4720ml, the average time of postoperative pain was 5 days. The operation of WAL was labor saving with less blood losing. Intraoperative and postoperative vital signs were stable in all patients, eccbymosis and edema were mild, the planeness of skin restored in 3 days after the operation. There no infection, hematoma, cutaneous necrosis and toxic reaction of lidocaine occurred, all patients responded fine in 6 months after the operation. Conclusion WAL is an effective and safe method for large volume Liposuction. Further study of safety of WAL in other fields should be carried out%目的 探讨应用水射流辅助吸脂术行全身大容量吸脂的临床效果和安全性.方法 对我科32例患者、共139个部位行水射流辅助吸脂,记录手术时间、注入肿胀液量、冲洗液量、吸出总液体量、吸出脂肪量、术后疼痛时间,观察吸出物颜色、术中术后患者生命体征、皮肤瘀斑和水肿的程度、皮肤平整度以及利多卡因毒性反应等并发症出现情况.结果 本组患者平均手术时间4.5h,平均吸脂4.8个部位,平均注入肿胀液量1850ml,平均注入冲洗液量15760ml,平均吸出总液体量11480ml,平均吸脂量4720ml,平均疼痛恢复时间5

  2. Large-scale preparation of the homogeneous LolA lipoprotein complex and efficient in vitro transfer of lipoproteins to the outer membrane in a LolB-dependent manner.

    Science.gov (United States)

    Watanabe, Shoji; Oguchi, Yuki; Yokota, Naoko; Tokuda, Hajime

    2007-12-01

    An ATP-binding cassette transporter LolCDE complex of Escherichia coli releases lipoproteins destined to the outer membrane from the inner membrane as a complex with a periplasmic chaperone, LolA. Interaction of the LolA-lipoprotein complex with an outer membrane receptor, LolB, then causes localization of lipoproteins to the outer membrane. As far as examined, formation of the LolA-lipoprotein complex strictly depends on ATP hydrolysis by the LolCDE complex in the presence of LolA. It has been speculated, based on crystallographic and biochemical observations, that LolA undergoes an ATP-dependent conformational change upon lipoprotein binding. Thus, preparation of a large amount of the LolA-lipoprotein complex is difficult. Moreover, lipoproteins bound to LolA are heterogeneous. We report here that the coexpression of LolA and outer membrane-specific lipoprotein Pal from a very efficient plasmid causes the unusual accumulation of the LolA-Pal complex in the periplasm. The complex was purified to homogeneity and shown to be a functional intermediate of the lipoprotein localization pathway. In vitro incorporation of Pal into outer membranes revealed that a single molecule of LolB catalyzes the incorporation of more than 100 molecules of Pal into outer membranes. Moreover, the LolB-dependent incorporation of Pal was not affected by excess-free LolA, indicating that LolB specifically interacts with liganded LolA. Finally, the LolB depletion caused the accumulation of a significant amount of Pal in the periplasm, thereby establishing the conditions for preparation of the homogeneous LolA-lipoprotein complex.

  3. Determination of ethyl glucuronide in hair samples of Chinese people by protein precipitation (PPT) and large volume injection-gas chromatography-tandem mass spectrometry (LVI-GC/MS/MS).

    Science.gov (United States)