The estimation of differential counting measurements of possitive quantities with relatively large statistical errors

International Nuclear Information System (INIS)

Vincent, C.H.

1982-01-01

Bayes' principle is applied to the differential counting measurement of a positive quantity in which the statistical errors are not necessarily small in relation to the true value of the quantity. The methods of estimation derived are found to give consistent results and to avoid the anomalous negative estimates sometimes obtained by conventional methods. One of the methods given provides a simple means of deriving the required estimates from conventionally presented results and appears to have wide potential applications. Both methods provide the actual posterior probability distribution of the quantity to be measured. A particularly important potential application is the correction of counts on low radioacitvity samples for background. (orig.)

IAEA regulatory initiatives for the air transport of large quantities of radioactive materials

International Nuclear Information System (INIS)

Luna, R.E.; Wangler, M.W.; Selling, H.A.

1993-01-01

The International Atomic Energy Agency (IAEA) has been laboring since 1988 over a far reaching change to its model regulations (IAEA, 1990) for the transport of radioactive materials (RAM). This change could impact the manner in which certain classes of radioactive materials are shipped by air and change some of the basic tenets of radioactive material transport regulations around the world. Few technical issues remain in determining the shape of the IAEA's revision of its regulations to accommodate air transport of large quantities of radioactive material. In the next two years the detailed wording of the regulations will be fully worked out and proposed for inclusion in SS6. Considering the breadth of the member state participation in the process, it seems likely that the approved version of the 1995 revision of SS6 will contain air mode revisions that move away from the predominantly mode independent character that characterized their first 30 years. (J.P.N.)

The air transport of radioactive material in large quantities or with high activity

International Nuclear Information System (INIS)

1993-04-01

The present TECDOC is a mixture of new regulatory provisions for the air transport of large quantities of radioactive material, explanatory and background material for these new provisions and other issues which have been discussed by the various technical committees, advisory groups and consultants that contributed to its development. It represents the broad consensus that has been reached between IAEA Member States on the major fundamental issues related to air transport of radioactive material with high potential hazard. The most visible novelty in the TECDOC is the proposal to introduce a new package type, the Type C package. The material contained in the TECDOC will be subject to further scrutiny by Member States and be cognizant international organizations. It is intended that the new regulatory provisions will be incorporated in the new, comprehensively revised Edition of the Regulations, due in 1996. To let the regulatory provisions proper stand out from background material it is printed in italics throughout the TECDOC. 33 refs, 6 figs

Average Transverse Momentum Quantities Approaching the Lightfront

OpenAIRE

Boer, Daniel

2015-01-01

In this contribution to Light Cone 2014, three average transverse momentum quantities are discussed: the Sivers shift, the dijet imbalance, and the $p_T$ broadening. The definitions of these quantities involve integrals over all transverse momenta that are overly sensitive to the region of large transverse momenta, which conveys little information about the transverse momentum distributions of quarks and gluons inside hadrons. TMD factorization naturally suggests alternative definitions of su...

DOE approach to threshold quantities

International Nuclear Information System (INIS)

Wickham, L.E.; Kluk, A.F.; Department of Energy, Washington, DC)

1985-01-01

The Department of Energy (DOE) is developing the concept of threshold quantities for use in determining which waste materials must be handled as radioactive waste and which may be disposed of as nonradioactive waste at its sites. Waste above this concentration level would be managed as radioactive or mixed waste (if hazardous chemicals are present); waste below this level would be handled as sanitary waste. Ideally, the threshold must be set high enough to significantly reduce the amount of waste requiring special handling. It must also be low enough so that waste at the threshold quantity poses a very small health risk and multiple exposures to such waste would still constitute a small health risk. It should also be practical to segregate waste above or below the threshold quantity using available instrumentation. Guidance is being prepared to aid DOE sites in establishing threshold quantity values based on pathways analysis using site-specific parameters (waste stream characteristics, maximum exposed individual, population considerations, and site specific parameters such as rainfall, etc.). A guidance dose of between 0.001 to 1.0 mSv/y (0.1 to 100 mrem/y) was recommended with 0.3 mSv/y (30 mrem/y) selected as the guidance dose upon which to base calculations. Several tasks were identified, beginning with the selection of a suitable pathway model for relating dose to the concentration of radioactivity in the waste. Threshold concentrations corresponding to the guidance dose were determined for waste disposal sites at a selected humid and arid site. Finally, cost-benefit considerations at the example sites were addressed. The results of the various tasks are summarized and the relationship of this effort with related developments at other agencies discussed

Lessons learned in streamlining the preparation of SNM standard solutions

International Nuclear Information System (INIS)

Clark, J.P.; Johnson, S.R.

1986-01-01

Improved safeguard measurements have produced a demand for greater quantities of reliable SNM solution standards. At the Savannah River Plant (SRP), the demand for these standards has been met by several innovations to improve the productivity and reliability of standards preparations. With the use of computer controlled balance, large batches of SNM stock solutions are prepared on a gravimetric basis. Accurately dispensed quantities of the stock solution are weighed and stored in bottles. When needed, they are quantitatively transferred to tared containers, matrix adjusted to target concentrations, weighed, and measured for density at 25 0 C. Concentrations of SNM are calculated both gravimetrically and volumetrically. Calculated values are confirmed analytically before the standards are used in measurement control program (MCP) activities. The lessons learned include: MCP goals include error identification and management. Strategy modifications are required to improve error management. Administrative controls can minimize certain types of errors. Automation can eliminate redundancy and streamline preparations. Prudence and simplicity enhance automation success. The effort expended to increase productivity has increased the reliability of standards and provided better documentation for quality assurance

A statistical law in the perception of risks and physical quantities in traffic

DEFF Research Database (Denmark)

Elvik, Rune

2015-01-01

This paper suggests that a universal psychophysical law influences the perception of risks and physical quantities in traffic. This law states that there will be a tendency to overestimate low probabilities or small quantities, while high probabilities or large quantities may be underestimated....... Studies of the perception of risk and physical quantities in traffic have found a highly consistent pattern....

Preparation of crystalline sodium norcarnitine: an easily handled precursor for the preparation of carnitine analogs and radiolabeled carnitine.

Science.gov (United States)

Colucci, W J; Turnbull, S P; Gandour, R D

1987-05-01

A procedure by which crystalline sodium norcarnitine can be prepared in large quantities and high yields has been developed. Carnitine is selectively demethylated by thiophenoxide ion in N,N-dimethylethanolamine. The reactive thiophenoxide ion is generated in situ by addition of thiophenol to this basic reaction solvent. Hence, sodium thiophenoxide, which has been used in similar applications, but is difficult to prepare, can be avoided. Accordingly, reaction of (R,S)-carnitine followed by aqueous azeotropic distillation of byproducts as well as excess starting materials and then by neutralization with sodium hydroxide gave sodium norcarnitine in 89% yield. (R)-Carnitine gave 91% yield of (R)-norcarnitine zwitterion before neutralization. A method for the facile preparation of radiolabeled (R)-carnitine is also described. Thus, methylation of sodium norcarnitine with methyl iodide in methanolic acetone produced carnitine, which precipitated, and sodium iodide, which was soluble.

选煤厂数质量平衡管理的应用研究%Study on quantity and quality balance control in coal preparation plant

Institute of Scientific and Technical Information of China (English)

杜欣莉

2011-01-01

According to analyzing the technical process in Jinyang coal preparation plant, the best control points in the whole process were defined based on the quantity and quailty balance control principle of coal preparation products. All those improving methods can increase the total yield of coal preparation product, which means there will be a better economic benefits. It can get more accurate variable data and the management level is improved.%通过分析晋阳选煤厂工艺流程,根据洗选产品的数质量平衡原则确定了工序质量点,提出了强化生产过程数质量管理的思路,以保证洗选产品的综合产率,分析各计量数据的可靠性,提高企业的经营管理水平和经济效益.

Photosynthesis-related quantities for education and modeling.

Science.gov (United States)

Antal, Taras K; Kovalenko, Ilya B; Rubin, Andrew B; Tyystjärvi, Esa

2013-11-01

A quantitative understanding of the photosynthetic machinery depends largely on quantities, such as concentrations, sizes, absorption wavelengths, redox potentials, and rate constants. The present contribution is a collection of numbers and quantities related mainly to photosynthesis in higher plants. All numbers are taken directly from a literature or database source and the corresponding reference is provided. The numerical values, presented in this paper, provide ranges of values, obtained in specific experiments for specific organisms. However, the presented numbers can be useful for understanding the principles of structure and function of photosynthetic machinery and for guidance of future research.

Strongly intensive quantities

International Nuclear Information System (INIS)

Gorenstein, M. I.; Gazdzicki, M.

2011-01-01

Analysis of fluctuations of hadron production properties in collisions of relativistic particles profits from use of measurable intensive quantities which are independent of system size variations. The first family of such quantities was proposed in 1992; another is introduced in this paper. Furthermore we present a proof of independence of volume fluctuations for quantities from both families within the framework of the grand canonical ensemble. These quantities are referred to as strongly intensive ones. Influence of conservation laws and resonance decays is also discussed.

Proteomic Challenges: Sample Preparation Techniques for Microgram-Quantity Protein Analysis from Biological Samples

Directory of Open Access Journals (Sweden)

Peter Feist

2015-02-01

Full Text Available Proteins regulate many cellular functions and analyzing the presence and abundance of proteins in biological samples are central focuses in proteomics. The discovery and validation of biomarkers, pathways, and drug targets for various diseases can be accomplished using mass spectrometry-based proteomics. However, with mass-limited samples like tumor biopsies, it can be challenging to obtain sufficient amounts of proteins to generate high-quality mass spectrometric data. Techniques developed for macroscale quantities recover sufficient amounts of protein from milligram quantities of starting material, but sample losses become crippling with these techniques when only microgram amounts of material are available. To combat this challenge, proteomicists have developed micro-scale techniques that are compatible with decreased sample size (100 μg or lower and still enable excellent proteome coverage. Extraction, contaminant removal, protein quantitation, and sample handling techniques for the microgram protein range are reviewed here, with an emphasis on liquid chromatography and bottom-up mass spectrometry-compatible techniques. Also, a range of biological specimens, including mammalian tissues and model cell culture systems, are discussed.

Proteomic Challenges: Sample Preparation Techniques for Microgram-Quantity Protein Analysis from Biological Samples

Science.gov (United States)

Feist, Peter; Hummon, Amanda B.

2015-01-01

Proteins regulate many cellular functions and analyzing the presence and abundance of proteins in biological samples are central focuses in proteomics. The discovery and validation of biomarkers, pathways, and drug targets for various diseases can be accomplished using mass spectrometry-based proteomics. However, with mass-limited samples like tumor biopsies, it can be challenging to obtain sufficient amounts of proteins to generate high-quality mass spectrometric data. Techniques developed for macroscale quantities recover sufficient amounts of protein from milligram quantities of starting material, but sample losses become crippling with these techniques when only microgram amounts of material are available. To combat this challenge, proteomicists have developed micro-scale techniques that are compatible with decreased sample size (100 μg or lower) and still enable excellent proteome coverage. Extraction, contaminant removal, protein quantitation, and sample handling techniques for the microgram protein range are reviewed here, with an emphasis on liquid chromatography and bottom-up mass spectrometry-compatible techniques. Also, a range of biological specimens, including mammalian tissues and model cell culture systems, are discussed. PMID:25664860

Proteomic challenges: sample preparation techniques for microgram-quantity protein analysis from biological samples.

Science.gov (United States)

Feist, Peter; Hummon, Amanda B

2015-02-05

Proteins regulate many cellular functions and analyzing the presence and abundance of proteins in biological samples are central focuses in proteomics. The discovery and validation of biomarkers, pathways, and drug targets for various diseases can be accomplished using mass spectrometry-based proteomics. However, with mass-limited samples like tumor biopsies, it can be challenging to obtain sufficient amounts of proteins to generate high-quality mass spectrometric data. Techniques developed for macroscale quantities recover sufficient amounts of protein from milligram quantities of starting material, but sample losses become crippling with these techniques when only microgram amounts of material are available. To combat this challenge, proteomicists have developed micro-scale techniques that are compatible with decreased sample size (100 μg or lower) and still enable excellent proteome coverage. Extraction, contaminant removal, protein quantitation, and sample handling techniques for the microgram protein range are reviewed here, with an emphasis on liquid chromatography and bottom-up mass spectrometry-compatible techniques. Also, a range of biological specimens, including mammalian tissues and model cell culture systems, are discussed.

Price effects of changing quantities supplied at the integrated european fish market

DEFF Research Database (Denmark)

Nielsen, Max; Smit, Jos; Guillen, Jordi

2012-01-01

to be −1.1. This implies that price flexibilities previously estimated for single European countries underestimate price changes at the European level caused by quantity changes. Results indicate that changing quantities can increase revenues from individual species with large own-price flexibilities...

Sample preparation for large-scale bioanalytical studies based on liquid chromatographic techniques.

Science.gov (United States)

Medvedovici, Andrei; Bacalum, Elena; David, Victor

2018-01-01

Quality of the analytical data obtained for large-scale and long term bioanalytical studies based on liquid chromatography depends on a number of experimental factors including the choice of sample preparation method. This review discusses this tedious part of bioanalytical studies, applied to large-scale samples and using liquid chromatography coupled with different detector types as core analytical technique. The main sample preparation methods included in this paper are protein precipitation, liquid-liquid extraction, solid-phase extraction, derivatization and their versions. They are discussed by analytical performances, fields of applications, advantages and disadvantages. The cited literature covers mainly the analytical achievements during the last decade, although several previous papers became more valuable in time and they are included in this review. Copyright © 2017 John Wiley & Sons, Ltd.

Development of technology for the large-scale preparation of 60Co polymer film source

International Nuclear Information System (INIS)

Udhayakumar, J.; Pardeshi, G.S.; Gandhi, Shymala S.; Chakravarty, Rubel; Kumar, Manoj; Dash, Ashutosh; Venkatesh, Meera

2008-01-01

60 Co sources (∼37 kBq) in the form of a thin film are widely used in position identification of perforation in offshore oil-well explorations. This paper describes the large-scale preparation of such sources using a radioactive polymer containing 60 Co. 60 Co was extracted into chloroform containing 8-hydroxyquinoline. The chloroform layer was mixed with polymethyl methacrylate (PMMA) polymer. A large film was prepared using the polymer solution containing the complex. The polymer film was then cut into circular sources, mounted on a source holder and supplied to various users

Application of cooperative and non-cooperative games in large-scale water quantity and quality management: a case study.

Science.gov (United States)

Mahjouri, Najmeh; Ardestani, Mojtaba

2011-01-01

In this paper, two cooperative and non-cooperative methodologies are developed for a large-scale water allocation problem in Southern Iran. The water shares of the water users and their net benefits are determined using optimization models having economic objectives with respect to the physical and environmental constraints of the system. The results of the two methodologies are compared based on the total obtained economic benefit, and the role of cooperation in utilizing a shared water resource is demonstrated. In both cases, the water quality in rivers satisfies the standards. Comparing the results of the two mentioned approaches shows the importance of acting cooperatively to achieve maximum revenue in utilizing a surface water resource while the river water quantity and quality issues are addressed.

The treatment of large quantities of high fluorin contents UO2 by ammonium double uranate (ADU) techniques

International Nuclear Information System (INIS)

Wang Bangwu; Chen Ying

2010-01-01

The paper has discussed the sinter action of UO 2 in low temperature. The study indicates the over hot part of UO 2 by the deoxidization hot of oxidation uranate mostly results in the sinter in the process of trans form ADU into UO 2 . The UO 2 settling times in kiln little influences the sinter performance of UO 2 in the same condition of high fluorin contents UO 2 returning kiln, and high fluorin contents UO 2 returning kiln does not sinter UO 2 again. Experiment on large quantities of high fluorin contents UO 2 by Ammonium Double Uranate (ADU) techniques direct returning kiln, the result shows the sinter performance of UO 2 doesn't drop in the process of high fluor in contents UO 2 direct returning kiln, and the performance of UO 2 can meet specification. (authors)

Detection Dynamics Of Nitrogen Based Explosive Quantities In Selected Cylindrical Containers

Directory of Open Access Journals (Sweden)

Ngusha Tavershima Almighty

2017-12-01

Full Text Available An experimental set up for examining the variation of detection intensity with explosive quantity has been studied. Containers made from ceramic carbon steel wood and HDPE were filled with explosive masses ranging from 10 kg to 500 kg and irradiated by a 14.1 MeV point isotropic neutron source. The resulting gamma photons were analyzed for their C N and O composition and the sum computed to yield a quantity known as the material quotient MQ. Examination of MQ values indicates an initial increase in detection intensity with increasing explosive quantity. Saturation is however reached at an explosive quantity of about 25kg where detection intensity reduces with further increase in explosive quantity. Effects of variation in explosive quantity appeared to be more pronounced for explosives contained in HDPE and wooden containers and least pronounced for those in steel containers. Source-detector configuration was identified as a major factor affecting effective detection of large masses of explosives.

Efficient preparation of large-block-code ancilla states for fault-tolerant quantum computation

Science.gov (United States)

Zheng, Yi-Cong; Lai, Ching-Yi; Brun, Todd A.

2018-03-01

Fault-tolerant quantum computation (FTQC) schemes that use multiqubit large block codes can potentially reduce the resource overhead to a great extent. A major obstacle is the requirement for a large number of clean ancilla states of different types without correlated errors inside each block. These ancilla states are usually logical stabilizer states of the data-code blocks, which are generally difficult to prepare if the code size is large. Previously, we have proposed an ancilla distillation protocol for Calderbank-Shor-Steane (CSS) codes by classical error-correcting codes. It was assumed that the quantum gates in the distillation circuit were perfect; however, in reality, noisy quantum gates may introduce correlated errors that are not treatable by the protocol. In this paper, we show that additional postselection by another classical error-detecting code can be applied to remove almost all correlated errors. Consequently, the revised protocol is fully fault tolerant and capable of preparing a large set of stabilizer states sufficient for FTQC using large block codes. At the same time, the yield rate can be boosted from O (t-2) to O (1 ) in practice for an [[n ,k ,d =2 t +1

Preparation and provisional validation of a large size dried spike: Batch SAL-9931

International Nuclear Information System (INIS)

Jammet, G.; Zoigner, A.; Doubek, N.; Grabmueller, G.; Bagliano, G.

1990-05-01

To determine uranium and plutonium concentration using isotope dilution mass spectrometry, weighed aliquands of a synthetic mixture containing about 2 mg of Pu (with a 239 Pu abundance of about 98%) and 40 mg of U (with a 235 U enrichment of about 19%) have been prepared and verified by SAL to be used to spike samples of concentrated spent fuel solutions with a high burn-up and a low 235 U enrichment. The advantages of such a Large Size Dried (LSD) Spike have been pointed out elsewhere and proof of the usefulness in the field reported. Certified Reference Materials Pu-NBL-126, natural U-NBS-960 and 93% enriched U-NBL-116 were used to prepare a stock solution containing 1.8 mg/ml of Pu and 37.3 mg/ml of 19.4% enriched U. Before shipment to the Reprocessing Plant, aliquands of the stock solution are dried to give Large Size Dried Spikes which resist shocks encountered during transportation, so that they can readily be recovered quantitatively at the plant. This paper describes the preparation and the validation of a Large Size Dried Spike which is intended to be used as a common spike by the plant operator, the national and the IAEA inspectorates. 6 refs, 7 tabs

Impact of the Velo 2 half misalignment on physical quantities

CERN Document Server

Roguljic, Matej; Borghi, Silvia; Grillo, Lucia; CERN. Geneva. EP Department

2016-01-01

The impact of the misalignment of the Vertex Locator of the LHCb experiment on the physical quantities of the decay "$D^{*+} \\rightarrow (D^{0}\\rightarrow K^{-}\\pi^{+}) \\pi^{+} $" is studied in this note. Different misalignments of the 2 halves are applied to Monte Carlo data and the variations of the physical quantities with respect to the case without misalignment are evaluated. The results show the importance of the VELO 2 half alignment which can significantly affect the physics performance in the large misalignment case. A misalignment equal to the precision of the real-time alignment of the Vertex Locator is found to have a negligible effect on the studied physical quantities.

Machine Learning and Deep Learning Models to Predict Runoff Water Quantity and Quality

Science.gov (United States)

Bradford, S. A.; Liang, J.; Li, W.; Murata, T.; Simunek, J.

2017-12-01

Contaminants can be rapidly transported at the soil surface by runoff to surface water bodies. Physically-based models, which are based on the mathematical description of main hydrological processes, are key tools for predicting surface water impairment. Along with physically-based models, data-driven models are becoming increasingly popular for describing the behavior of hydrological and water resources systems since these models can be used to complement or even replace physically based-models. In this presentation we propose a new data-driven model as an alternative to a physically-based overland flow and transport model. First, we have developed a physically-based numerical model to simulate overland flow and contaminant transport (the HYDRUS-1D overland flow module). A large number of numerical simulations were carried out to develop a database containing information about the impact of various input parameters (weather patterns, surface topography, vegetation, soil conditions, contaminants, and best management practices) on runoff water quantity and quality outputs. This database was used to train data-driven models. Three different methods (Neural Networks, Support Vector Machines, and Recurrence Neural Networks) were explored to prepare input- output functional relations. Results demonstrate the ability and limitations of machine learning and deep learning models to predict runoff water quantity and quality.

[Establishment of modern multi-component sustained-release preparations of oral traditional Chinese medicines].

Science.gov (United States)

Xia, Hai-Jian; Zhang, Zhen-Hai; Liu, Dan; Yu, Dan-Hong; Jia, Xiao-Bin

2013-10-01

Traditional Chinese medicines have a long history, with a large quantity of efficient traditional Chinese medicines and prescriptions. However, the vast majority of pharmaceutical dose forms remain common preparations, with very few efficient, long-lasting and low-dose preparations. The sustain-release preparation allows sustained drug release in a longer period of time, maintains blood drug concentration, reduces the toxic effect and medication frequency, and improves medication compliance. Unlike monomer drugs, the material base of traditional Chinese medicine and compounds is multi-component, instead of single or several active monomers. Therefore, under the guidance of the Chinese medicine theories, modern multi-component sustained-release preparations were developed for oral traditional Chinese medicines, with the aim of finally improving the clinical efficacy of traditional Chinese medicines.

A document preparation system in a large network environment

Energy Technology Data Exchange (ETDEWEB)

Vigil, M.; Bouchier, S.; Sanders, C.; Sydoriak, S.; Wheeler, K.

1988-01-01

At Los Alamos National Laboratory, we have developed an integrated document preparation system that produces publication-quality documents. This system combines text formatters and computer graphics capabilities that have been adapted to meet the needs of users in a large scientific research laboratory. This paper describes the integration of document processing technology to develop a system architecture, based on a page description language, to provide network-wide capabilities in a distributed computing environment. We describe the Laboratory requirements, the integration and implementation issues, and the challenges we faced developing this system.

16 CFR 500.25 - Net quantity, average quantity, permitted variations.

Science.gov (United States)

2010-01-01

... good distribution practice and which unavoidably result in change of weight or mass or measure. (c... good packaging practice: Provided, that such variations shall not be permitted to such extent that the... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Net quantity, average quantity, permitted...

How tobacco companies have used package quantity for consumer targeting.

Science.gov (United States)

Persoskie, Alexander; Donaldson, Elisabeth A; Ryant, Chase

2018-05-31

Package quantity refers to the number of cigarettes or amount of other tobacco product in a package. Many countries restrict minimum cigarette package quantities to avoid low-cost packs that may lower barriers to youth smoking. We reviewed Truth Tobacco Industry Documents to understand tobacco companies' rationales for introducing new package quantities, including companies' expectations and research regarding how package quantity may influence consumer behaviour. A snowball sampling method (phase 1), a static search string (phase 2) and a follow-up snowball search (phase 3) identified 216 documents, mostly from the 1980s and 1990s, concerning cigarettes (200), roll-your-own tobacco (9), smokeless tobacco (6) and 'smokeless cigarettes' (1). Companies introduced small and large packages to motivate brand-switching and continued use among current users when faced with low market share or threats such as tax-induced price increases or competitors' use of price promotions. Companies developed and evaluated package quantities for specific brands and consumer segments. Large packages offered value-for-money and matched long-term, heavy users' consumption rates. Small packages were cheaper, matched consumption rates of newer and lighter users, and increased products' novelty, ease of carrying and perceived freshness. Some users also preferred small packages as a way to try to limit consumption or quit. Industry documents speculated about many potential effects of package quantity on appeal and use, depending on brand and consumer segment. The search was non-exhaustive, and we could not assess the quality of much of the research or other information on which the documents relied. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Radiation quantities and units

International Nuclear Information System (INIS)

2013-01-01

This fifth chapter presents the conceptual evolution, the definition procedures, the radiological quantities themselves, the relation between them, the new operational quantities and the new quantities defined in the ICRP 60 that replaced ICRP 26 and was included in the CNEN-NN-3.01 standard of 2011

Integrated coal preparation

International Nuclear Information System (INIS)

Buchanan, D.J.; Jones, T.F.

1992-01-01

Perceptions of quality have changed over the years. The attributes of a certain coal (its rank, slagging propensity, ash content etc) are traditionally referred to as its quality. However, the subject of this paper is quality in a much wider sense: quality as fitness for purpose: and all that such a wide definition entails. British Standard BS 5750 (ISO 9000) Quality Systems defines a systems approach to quality, and includes both the supplier of raw materials and the final customer within this boundary. Coal preparation starts at the production face. The greater the proportion of dirt in run-of-mine product the greater the challenge in satisfying the customer's needs. Significant advances have been made in minimizing mined dirt. For example, the sue of vertical steering on longwall faces improves productivity and quality. Unfortunately modern mining methods produce large quantities of fines, despite efforts to reduce them at the point of production and during transportation to the surface. Coal preparation also produces further fines. It has been estimated that fine coal costs 2.5 times as much to clean as large coal, and the costs of handing wet fine coal product will inflate this estimate. Handling considerations rightly concern our customers and are part of the wider meaning of quality. In this paper the authors address some novel solutions to the challenge posed by fines

Discovery of a new strain of murine rotavirus that is consistently shed in large quantities after oral inoculation of adult mice

International Nuclear Information System (INIS)

McNeal, Monica M.; Belli, Janine; Basu, Mitali; Choi, Anthony H.-C.; Ward, Richard L.

2004-01-01

In 1990, we developed the adult mouse model for studies on active immunity against shedding of the EDIM strain of murine rotavirus. Low and inconsistent levels of EDIM shedding in some strains of adult mice, particularly those on C57BL/6 backgrounds, established the need for an alternative murine rotavirus strain for these studies. Fortuitously, such a rotavirus strain was obtained from mice housed within the conventional colony at Children's Hospital. This strain, named EMcN, was clearly distinguishable from EDIM based on electropherotype. Furthermore, sequence analyses of VP4 and VP7 genes of EMcN revealed non-identities in 5% of the amino acids of both proteins relative to EDIM but established EMcN as another G3P[16] strain of murine rotavirus. Subgroup analysis showed EMcN belonged to SG1 while EDIM was found to be non-SG1/SG2. Similarly, unlike EDIM, the EMcN strain was identified as serotype G3 based on neutralization by hyperimmune antisera developed against prototype human and simian G3 rotavirus strains. Although EDIM produced more days of diarrhea and was shed in greater quantities in neonatal BALB/c mice, EMcN was shed in much greater quantities in adult BALB/c mice. More importantly, in contrast to the EDIM strain, EMcN was shown to be consistently shed in large quantities in adult C57BL/6 mice and ko mice on this background. Therefore, it is recommended that the EMcN strain be used for future challenge studies with mice on this background

Mining Waste Classification and Quantity of Non-Metal Minesin Slovenia

Directory of Open Access Journals (Sweden)

Ana Burger

2007-06-01

Full Text Available Mining is an important human activity that creates wealth and supplies materials for maintaining standard of living and further human development. However, mining has also negative impacts on the environment and society. One of them is the production of mining waste throughout the entire mining cycle, in particular in the mine development and operation /production stage.Due to the EU Directive 2006/21/EC on the management of waste from the extractive industries and its implementation in Member state, estimation on quality and quantity of mining waste from active non-metal mines in Slovenia was carried out. In the selected mines mining and processing was closely examined. With material flow analysis quantity and characteristics of mining waste were defined for several mines of different commodities.Data on mining waste were afterwards generalized in order to get an overall country evaluation on mining waste “production” of non-metal mines.Mining waste as a result of mining and beneficiation processes in non-metal mines of Slovenia is either inert or non-hazardous. Most of the mining waste is used for mine reclamation running simultaneously with the production phase. The largest amounts of mining waste per unit produced are created in dimension stone industry. Since the dimensionstone production is small, the waste amount is negligible. Large quantities of mining waste are produced in crushed stone and, sand and gravel operations, because aggregate production is pretty large with regard to other non-metals production in Slovenia. We can therefore conclude that large quantities of mining waste from non-metal mines, which are mostly used in reclamation and for side products, do not represent danger to the environment.

An automated synthesis module for preparation of L-3-[123I]iodo-alpha-methyl tyrosine

International Nuclear Information System (INIS)

Luurtsema, Gert; Jager, Pieter L.; Piers, Albertus; Hooge, Marjolijn N. de

2001-01-01

L-3-[ 123 I]iodo-alpha-methyl tyrosine (IMT) is an artificial amino acid suitable for SPECT imaging of various tumours. Manual synthesis of this radiopharmaceutical is reliable, but time-consuming and may require handling of large quantities of radioactivity. We developed an automated IMT synthesis module, which prepares a ready-to-inject product that meets radiopharmaceutical requirements and is identical to the manually synthesised equivalent. Current advantages include decreased operator assistance time and reduced radiation exposure. Application may be extended to other radiopharmaceuticals, including high-dose preparations for therapeutic use

Preparation of UO2 fragments for fuel-debris experiments

International Nuclear Information System (INIS)

Tinkle, M.C.; Kircher, J.A.; Zinn, R.M.; Eash, D.T.

1982-01-01

A unique process was developed for preparing multi-kilogram quantities of > 90% dense fragments of enriched and depleted UO 2 sized 20 mm to 0.038 mm for fuel debris experiments. Precipitates of UO 4 . xH 2 O were treated to obtain UO 2 powders that would yield large cohesive green pieces when isostatically pressed to 206 MPa. The pressed pieces were crushed into fragments that were about 30% oversized, and heated to 1800 0 C for 24 h in H 2 . Oversizing compensates for shrinkage during densification. Effort was dramatically reduced by working on a large scale and by presizing the green UO 2 instead of directly crushing densified pellets

Development of blueberry liquor: influence of distillate, sweetener and fruit quantity.

Science.gov (United States)

Caldeira, Ilda; Lopes, Daniel; Delgado, Teresa; Canas, Sara; Anjos, Ofélia

2018-02-01

In this work different formulations of blueberry liquor were tested and characterised based on their physico-chemical and sensory characteristics. Three factors were evaluated: the distillate used to produce the liquor (wine spirit or grape marc spirit); the sweetener (white sugar or honey) and the fruit quantity (two doses). For each liquor, pH, total acidity, dry soluble solids content, dry extract, alcoholic strength, reducing sugars, colour intensity, methanol content, acetaldehyde and fusel alcohols were determined. Sensory tests were carried out with a trained panel. The three factors studied significantly influenced the physico-chemical features of the liquors, being the quantity of fruit the most discriminating factor, except for the volatile compounds which were mainly influenced by the distillate. As regards the sensory analysis, it was found that the most appreciated liquor was that prepared with wine spirit, sugar and a lower dose of blueberry, and the less appreciated formulation was the one made with grape marc spirit, honey and a lower quantity of blueberry. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Novel regenerative large-volume immobilized enzyme reactor: preparation, characterization and application.

Science.gov (United States)

Ruan, Guihua; Wei, Meiping; Chen, Zhengyi; Su, Rihui; Du, Fuyou; Zheng, Yanjie

2014-09-15

A novel large-volume immobilized enzyme reactor (IMER) on small column was prepared with organic-inorganic hybrid silica particles and applied for fast (10 min) and oriented digestion of protein. At first, a thin enzyme support layer was formed in the bottom of the small column by polymerization with α-methacrylic acid and dimethacrylate. After that, amino SiO2 particles was prepared by the sol-gel method with tetraethoxysilane and 3-aminopropyltriethoxysilane. Subsequently, the amino SiO2 particles were activated by glutaraldehyde for covalent immobilization of trypsin. Digestive capability of large-volume IMER for proteins was investigated by using bovine serum albumin (BSA), cytochrome c (Cyt-c) as model proteins. Results showed that although the sequence coverage of the BSA (20%) and Cyt-c (19%) was low, the large-volume IMER could produce peptides with stable specific sequence at 101-105, 156-160, 205-209, 212-218, 229-232, 257-263 and 473-451 of the amino sequence of BSA when digesting 1mg/mL BSA. Eight of common peptides were observed during each of the ten runs of large-volume IMER. Besides, the IMER could be easily regenerated by reactivating with GA and cross-linking with trypsin after breaking the -C=N- bond by 0.01 M HCl. The sequence coverage of BSA from regenerated IMER increased to 25% comparing the non-regenerated IMER (17%). 14 common peptides. accounting for 87.5% of first use of IMER, were produced both with IMER and regenerated IMER. When the IMER was applied for ginkgo albumin digestion, the sequence coverage of two main proteins of ginkgo, ginnacin and legumin, was 56% and 55%, respectively. (Reviewer 2) Above all, the fast and selective digestion property of the large-volume IMER indicated that the regenerative IMER could be tentatively used for the production of potential bioactive peptides and the study of oriented protein digestion. Copyright © 2014 Elsevier B.V. All rights reserved.

Evaluation of a transposase protocol for rapid generation of shotgun high-throughput sequencing libraries from nanogram quantities of DNA.

Science.gov (United States)

Marine, Rachel; Polson, Shawn W; Ravel, Jacques; Hatfull, Graham; Russell, Daniel; Sullivan, Matthew; Syed, Fraz; Dumas, Michael; Wommack, K Eric

2011-11-01

Construction of DNA fragment libraries for next-generation sequencing can prove challenging, especially for samples with low DNA yield. Protocols devised to circumvent the problems associated with low starting quantities of DNA can result in amplification biases that skew the distribution of genomes in metagenomic data. Moreover, sample throughput can be slow, as current library construction techniques are time-consuming. This study evaluated Nextera, a new transposon-based method that is designed for quick production of DNA fragment libraries from a small quantity of DNA. The sequence read distribution across nine phage genomes in a mock viral assemblage met predictions for six of the least-abundant phages; however, the rank order of the most abundant phages differed slightly from predictions. De novo genome assemblies from Nextera libraries provided long contigs spanning over half of the phage genome; in four cases where full-length genome sequences were available for comparison, consensus sequences were found to match over 99% of the genome with near-perfect identity. Analysis of areas of low and high sequence coverage within phage genomes indicated that GC content may influence coverage of sequences from Nextera libraries. Comparisons of phage genomes prepared using both Nextera and a standard 454 FLX Titanium library preparation protocol suggested that the coverage biases according to GC content observed within the Nextera libraries were largely attributable to bias in the Nextera protocol rather than to the 454 sequencing technology. Nevertheless, given suitable sequence coverage, the Nextera protocol produced high-quality data for genomic studies. For metagenomics analyses, effects of GC amplification bias would need to be considered; however, the library preparation standardization that Nextera provides should benefit comparative metagenomic analyses.

Fuel handling alternatives to prepare for large scale fuel channel replacement

International Nuclear Information System (INIS)

Martire, S.; Sandu, I.

2007-01-01

It is desirable to reduce the duration of defuelling the reactor in preparation for retube, as the cost of replacement power is $750K/day. Three fast defuelling concepts are presented. With the Through Flow Defuelling method, the fuel string is hydraulically pushed into the downstream Fuelling Machine (FM) by flow passing through the fuel channel. The Long Stroke C Ram method replaces the FM C Ram with a longer one capable of pushing all fuel bundles into the receiving FM. Defuelling Hardware uses enhanced design of ram extensions that interconnect mechanically to extend the Ram stroke to push fuel bundles into the receiving FM. This paper will present descriptions of each defuelling concept to prepare for Large Scale Fuel Channel Replacement. Advantages and disadvantages of each concept will be discussed and a recommendation will be made for future implementation. (author)

Project plans for transuranic waste at small quantity sites in the Department of Energy comples-10522

International Nuclear Information System (INIS)

Mctaggart, Jerri Lynne; Lott, Sheila; Gadbury, Casey

2009-01-01

Los Alamos National Laboratory, Carlsbad Office (LANL-CO), has been tasked to write Project Plans for all of the Small Quantity Sites (SQS) with defense related Transuranic (TRU) waste in the Department of Energy (DOE) complex. Transuranic Work-Off Plans were precursors to the Project Plans. LANL-CO prepared a Work-Off Plan for each small quantity site. The Work-Off Plan that identified issues, drivers, schedules, and inventory. Eight sites have been chosen to deinventory their legacy TRU waste; Bettis Atomic Power Laboratory, General Electric-Vallecitos Nuclear Center, Lawrence Berkeley National Laboratory, Lawrence Livermore National Laboratory-Area 300, Nevada Test Site, Nuclear Radiation Development, Sandia National Laboratory, and the Separations Process Research Unit. Each plan was written for contact and/or remote handled waste if present at the site. These project plans will assist the small quantity sites to ship legacy TRU waste offsite and de-inventory the site of legacy TRU waste. The DOE is working very diligently to reduce the nuclear foot print in the United States. Each of the eight SQSs will be de-inventoried of legacy TRU waste during a campaign that ends September 2011. The small quantity sites have a fraction of the waste that large quantity sites possess. During this campaign, the small quantity sites will package all of the legacy TRU waste and ship to Idaho or directly to the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico. The sites will then be removed from the Transuranic Waste Inventory if they are de-inventoried of all waste. Each Project Plan includes the respective site inventory report, schedules, resources, drivers and any issues. These project plans have been written by the difficult waste team and will be approved by each site. Team members have been assigned to each site to write site specific project plans. Once the project plans have been written, the difficult team members will visit the sites to ensure nothing has

Property of Fluctuations of Sales Quantities by Product Category in Convenience Stores.

Directory of Open Access Journals (Sweden)

Gaku Fukunaga

Full Text Available The ability to ascertain the extent of product sale fluctuations for each store and locality is indispensable to inventory management. This study analyzed POS data from 158 convenience stores in Kawasaki City, Kanagawa Prefecture, Japan and found a power scaling law between the mean and standard deviation of product sales quantities for several product categories. For the statistical domains of low sales quantities, the power index was 1/2; for large sales quantities, the power index was 1, so called Taylor's law holds. The value of sales quantities with changing power indixes differed according to product category. We derived a Poissonian compound distribution model taking into account fluctuations in customer numbers to show that the scaling law could be explained theoretically for most of items. We also examined why the scaling law did not hold in some exceptional cases.

Property of Fluctuations of Sales Quantities by Product Category in Convenience Stores.

Science.gov (United States)

Fukunaga, Gaku; Takayasu, Hideki; Takayasu, Misako

2016-01-01

The ability to ascertain the extent of product sale fluctuations for each store and locality is indispensable to inventory management. This study analyzed POS data from 158 convenience stores in Kawasaki City, Kanagawa Prefecture, Japan and found a power scaling law between the mean and standard deviation of product sales quantities for several product categories. For the statistical domains of low sales quantities, the power index was 1/2; for large sales quantities, the power index was 1, so called Taylor's law holds. The value of sales quantities with changing power indixes differed according to product category. We derived a Poissonian compound distribution model taking into account fluctuations in customer numbers to show that the scaling law could be explained theoretically for most of items. We also examined why the scaling law did not hold in some exceptional cases.

Quantity Stickiness versus Stackelberg Leadership

International Nuclear Information System (INIS)

Ferreira, F. A.

2008-01-01

We study the endogenous Stackelberg relations in a dynamic market. We analyze a twice-repeated duopoly where, in the beginning, each firm chooses either a quantity-sticky production mode or a quantity-flexible production mode. The size of the market becomes observable after the first period. In the second period, a firm can adjust its quantity if, and only if, it has adopted the flexible mode. Hence, if one firm chooses the sticky mode whilst the other chooses the flexible mode, then they respectively play the roles of a Stackelberg leader and a Stackelberg follower in the second marketing period. We compute the supply quantities at equilibrium and the corresponding expected profits of the firms. We also analyze the effect of the slope parameter of the demand curve on the expected supply quantities and on the profits.

7 CFR 201.33 - Seed in bulk or large quantities; seed for cleaning or processing.

Science.gov (United States)

2010-01-01

... quantities; seed for cleaning or processing. (a) In the case of seed in bulk, the information required under... seeds. (b) Seed consigned to a seed cleaning or processing establishment, for cleaning or processing for... pertaining to such seed show that it is “Seed for processing,” or, if the seed is in containers and in...

How necessary are the new quantities

International Nuclear Information System (INIS)

Kraus, W.

1991-01-01

The necessity of the ICRU operational quantities is discussed from the point of view of practical, opertional radiation protection, on the basis of ICRU report 43. It is clear that, although the new quantities have some advantages over previous systems of operational quantities, there are some disadvantages as well. The decision to adopt these quantities is, therefore, not clear cut. (orig.)

Valuation of Construction Projects Based on of Quantity Scale by using Expert System

Directory of Open Access Journals (Sweden)

Entisar Kadhim Rasheed

2016-02-01

Full Text Available The subject of an valuation of quality of construction projects is one of the topics which it becomes necessary of the absence of the quantity standards in measuring the control works and the quality valuation standards in constructional projects. In the time being it depends on the experience of the workers which leads to an apparent differences in the valuation. The idea of this research came to put the standards to evaluate the quality of the projects in a special system depending on quantity scale nor quality specifying in order to prepare an expert system “ Crystal “ to apply this special system to able the engineers to valuate the quality of their projects easily and in more accurate ways.

Diagnosing indicators of large-scale forcing of east-coast cyclogenesis

International Nuclear Information System (INIS)

Dowdy, Andrew J; Mills, Graham A; Timbal, Bertrand

2010-01-01

Extra-tropical cyclones that develop near the east coast of Australia often have severe consequences such as flash flooding and damaging winds and seas, as well as beneficial consequences such as being responsible for heavy rainfall events that contribute significantly to total rainfall and runoff. There is subjective evidence that the development of most major events, commonly known as East Coast Lows, is associated with the movement of a high amplitude upper-tropospheric trough system over eastern Australia. This paper examines a number of upper-tropospheric diagnostic quantities that might provide a basis for preparing a climatology of the large-scale drivers of east-coast cyclogenesis. A preliminary climatology of these diagnostic quantities, based on ECMWF interim reanalyses, is compared with a database of observed East Coast Low events. The potential application of these diagnostics to global climate model simulations of past and future climates is also discussed.

Optimizing basin-scale coupled water quantity and water quality management with stochastic dynamic programming

DEFF Research Database (Denmark)

Davidsen, Claus; Liu, Suxia; Mo, Xingguo

2015-01-01

Few studies address water quality in hydro-economic models, which often focus primarily on optimal allocation of water quantities. Water quality and water quantity are closely coupled, and optimal management with focus solely on either quantity or quality may cause large costs in terms of the oth......-er component. In this study, we couple water quality and water quantity in a joint hydro-economic catchment-scale optimization problem. Stochastic dynamic programming (SDP) is used to minimize the basin-wide total costs arising from water allocation, water curtailment and water treatment. The simple water...... quality module can handle conservative pollutants, first order depletion and non-linear reactions. For demonstration purposes, we model pollutant releases as biochemical oxygen demand (BOD) and use the Streeter-Phelps equation for oxygen deficit to compute the resulting min-imum dissolved oxygen...

Radiation quantities and units

International Nuclear Information System (INIS)

1980-01-01

This report supersedes ICRU Report 19. Since ICRU Report 19 was published, a number of discussions have taken place between members of the Report Committee on Fundamental Quantities and Units and other workers in the field. Some of these discussions have resulted in the acceptance of certain modifications in the material set out in Report 19 and these modifications are incorporated in the current report. In addition, there has been some expansion and rearrangement of the material in the earlier report. In line, with providing more didactic material and useful source material for other ICRU reports, the general considerations in subsection 1.A of Report 19 have been expanded and placed in a separate subsection. The additional material includes discussions of four terms that are used in this document - quantity, unit, stochastic, and non-stochastic - along with a brief discussion of the mathematical formalism used in ICRU reports. As in ICRU Report 19, the definitions of quantities and units specifically designed for radiation protection (Part B) are separated from those of the general quantities (Part A). The inclusion of the index concept outlined in ICRU Report 25[4] required an extension of Part B

Multidemand Multisource Order Quantity Allocation with Multiple Transportation Alternatives

Directory of Open Access Journals (Sweden)

Jun Gang

2015-01-01

Full Text Available This paper focuses on a multidemand multisource order quantity allocation problem with multiple transportation alternatives. To solve this problem, a bilevel multiobjective programming model under a mixed uncertain environment is proposed. Two levels of decision makers are considered in the model. On the upper level, the purchaser aims to allocate order quantity to multiple suppliers for each demand node with the consideration of three objectives: total purchase cost minimization, total delay risk minimization, and total defect risk minimization. On the lower level, each supplier attempts to optimize the transportation alternatives with total transportation and penalty costs minimization as the objective. In contrast to prior studies, considering the information asymmetry in the bilevel decision, random and fuzzy random variables are used to model uncertain parameters of the construction company and the suppliers. To solve the bilevel model, a solution method based on Kuhn-Tucker conditions, sectional genetic algorithm, and fuzzy random simulation is proposed. Finally, the applicability of the proposed model and algorithm is evaluated through a practical case from a large scale construction project. The results show that the proposed model and algorithm are efficient in dealing with practical order quantity allocation problems.

Characteristics and Laser Performance of Yb3+-Doped Silica Large Mode Area Fibers Prepared by Sol–Gel Method

Directory of Open Access Journals (Sweden)

Shikai Wang

2013-12-01

Full Text Available Large-size 0.1 Yb2O3–1.0 Al2O3–98.9 SiO2 (mol% core glass was prepared by the sol–gel method. Its optical properties were evaluated. Both large mode area double cladding fiber (LMA DCF with core diameter of 48 µm and large mode area photonic crystal fiber (LMA PCF with core diameter of 90 µm were prepared from this core glass. Transmission loss at 1200 nm is 0.41 dB/m. Refractive index fluctuation is less than 2 × 10−4. Pumped by 976 nm laser diode LD pigtailed with silica fiber (NA 0.22, the slope efficiency of 54% and “light-to-light” conversion efficiency of 51% were realized in large mode area double cladding fiber, and 81 W laser power with a slope efficiency of 70.8% was achieved in the corresponding large mode area photonic crystal fiber.

A shared system of representation governing quantity discrimination in canids

Directory of Open Access Journals (Sweden)

Joseph M Baker

2012-10-01

Full Text Available One way to investigate the evolution of cognition is to compare the abilities of phylogenetically related species. The domestic dog (Canis lupus familiaris, for example, still shares cognitive abilities with the coyote (C. latrans. Both of these canids possess the ability to make psychophysical less/more discriminations of food based on quantity. Like many other species including humans, this ability is mediated by Weber’s Law: discrimination of continuous quantities is dependent on the ratio between the two quantities. As two simultaneously presented quantities of food become more similar, choice of the large or small option becomes random in both dogs and coyotes. It remains unknown, however, whether these closely related species within the same family—one domesticated, and one wild—make such quantitative comparisons with comparable accuracy. Has domestication honed or diminished this quantitative ability? Might different selective and ecological pressures facing coyotes drive them to be more or less able to accurately represent and discriminate food quantity than domesticated dogs? This study is an effort to elucidate this question concerning the evolution of non-verbal quantitative cognition.Here, we tested the quantitative discrimination ability of 16 domesticated dogs. Each animal was given 9 trials in which two different quantities of food were simultaneously displayed to them. The domesticated dogs’ performance on this task was then compared directly to the data from 16 coyotes’ performance on this same task reported by Baker and colleagues (2011.The quantitative discrimination abilities between the two species were strikingly similar. Domesticated dogs demonstrated similar quantitative sensitivity as coyotes, suggesting that domestication may not have significantly altered the psychophysical discrimination abilities of canids. Instead, this study provides further evidence for similar nonverbal quantitative abilities across

Are necessary unmeasurable quantities in radiation protection?

International Nuclear Information System (INIS)

David, M.G.; Correa, M.F.; Videira, A.A.P.

2016-01-01

We discuss in this paper the metrological status of unmeasurable protection quantities and the need to maintain these kind of quantities in the system. The discussion is based on reports from the institutions responsible for the quantities and on scientific publications. In conclusion, we can say that there are alternatives for changing the system in a way that it keep just measurable quantities, nevertheless the present system is well assimilated. Even though a proposal yet to be presented for changing the system, although might simplify and improve it, is not intended to overcome the existence of unmeasurable quantities or the two kinds of quantities. (author)

Automated Decisional Model for Optimum Economic Order Quantity Determination Using Price Regressive Rates

Science.gov (United States)

Roşu, M. M.; Tarbă, C. I.; Neagu, C.

2016-11-01

The current models for inventory management are complementary, but together they offer a large pallet of elements for solving complex problems of companies when wanting to establish the optimum economic order quantity for unfinished products, row of materials, goods etc. The main objective of this paper is to elaborate an automated decisional model for the calculus of the economic order quantity taking into account the price regressive rates for the total order quantity. This model has two main objectives: first, to determine the periodicity when to be done the order n or the quantity order q; second, to determine the levels of stock: lighting control, security stock etc. In this way we can provide the answer to two fundamental questions: How much must be ordered? When to Order? In the current practice, the business relationships with its suppliers are based on regressive rates for price. This means that suppliers may grant discounts, from a certain level of quantities ordered. Thus, the unit price of the products is a variable which depends on the order size. So, the most important element for choosing the optimum for the economic order quantity is the total cost for ordering and this cost depends on the following elements: the medium price per units, the stock cost, the ordering cost etc.

Guide for the preparation of applications for special nuclear material licenses of less than critical mass quantities - July 1976

International Nuclear Information System (INIS)

Anon.

1977-01-01

This guide describes the type of information needed to evaluate an application for a specific license for receipt, possession, use, and transfer of special nuclear material. It is intended for applicants requesting authorization to possess and use up to 2000 grams of plutonium, total, in the form of sealed plutonium-beryllium neutron sources, and any special nuclear material in quantities and forms not sufficient to form a critical mass. The latter quantities are considered to be 350 grams of contained uranium-235, 200 grams of uranium-233, 200 grams of plutonium (in any form other than plutonium-beryllium neutron sources) or any combination of them

HyLights: Preparation of the Large-Scale Demonstration Projects on Hydrogen for Transport in Europe

International Nuclear Information System (INIS)

Ulrich Bunger; Volker Blandow; Volker Jaensch; Harm Jeeninga; Cristina Morte Gomez

2006-01-01

The strategically important project HyLights has been launched by the European Commission in preparation of the large scale demonstration projects in transition to hydrogen as a fuel and long-term renewable energy carrier. HyLights, monitors concluded/ongoing demonstration projects and assists the planning of the next demonstration project phase, putting a clear focus on hydrogen in transport. HyLights is a coordination action that comprises 5 tasks to: 1) develop an assessment framework for concluded/ongoing demonstration projects, 2) analyse individual projects and establish a project database, 3) carry out a gaps analysis and prepare a requirement profile for the next stage projects, 4) assess and identify necessary financial and legal steps in preparation of the new projects, and 5) develop a European Initiative for the Growth of Hydrogen for Transport (EIGHT). (authors)

Dangerous quantities of radioactive material (D-values)

International Nuclear Information System (INIS)

2010-01-01

Radioactive material is widely used in industry, medicine, education and agriculture. In addition, it occurs naturally. The health risk posed by these materials vary widely depending on many factors, the most important of which are the amount of the material involved and its physical and chemical form. Therefore, there is a need to identify the quantity and type of radioactive material for which emergency preparedness and other arrangements (e.g. security) are warrant due to the health risk they pose. The aim of this publication is to provide practical guidance for Member States on that quantity of radioactive material that may be considered dangerous. A dangerous quantity is that, which if uncontrolled, could be involved in a reasonable scenario resulting in the death of an exposed individual or a permanent injury, which decreases that person's quality of life. This publication is published as part of the IAEA Emergency Preparedness and Response Series. It supports several publications including: the IAEA Safety Requirements 'Preparedness and Response for a Nuclear or Radiological Emergency', IAEA Safety Standards Series No. GS-R-2. IAEA, Vienna (2002). IAEA Safety Guide 'Categorization of Radioactive Sources', IAEA Safety Standards Series No RS-G-1.9, IAEA, Vienna (2005) and IAEA Safety Guide 'Arrangements for Preparedness for a Nuclear or Radiological Emergency' IAEA Safety Standards Series No. GS-G-2.1, IAEA, Vienna (2006). The procedures and data in this publication have been prepared with due attention to accuracy. However, as part of the review process, they undergo ongoing quality assurance checks. Comments are welcome and, following a period that will allow for a more extensive review, the IAEA may revise this publication as part of the process of continuous improvement. The publication uses a number of exposure scenarios, risk models and dosimetric data, which could be used during the response to nuclear or radiological emergency or other purposes

Collection and preparation of samples for gamma spectrometry

International Nuclear Information System (INIS)

Pan Jingquan

1994-01-01

The paper presents the basic principles of sample collection and preparation: setting up unified sampling program, methods and procedures, sample packing, transportation and storage, determination of sample quantity, sample pretreatment and preparation of samples to be analysed, etc. for gamma spectrometry. And the paper also describes briefly the main methods and special issues of sampling and preparation for the same environmental and biological samples, such as, air, water, grass, soil and foods

Eco-friendly preparation of large-sized graphene via short-circuit discharge of lithium primary battery.

Science.gov (United States)

Kang, Shaohong; Yu, Tao; Liu, Tingting; Guan, Shiyou

2018-02-15

We proposed a large-sized graphene preparation method by short-circuit discharge of the lithium-graphite primary battery for the first time. LiC x is obtained through lithium ions intercalation into graphite cathode in the above primary battery. Graphene was acquired by chemical reaction between LiC x and stripper agents with dispersion under sonication conditions. The gained graphene is characterized by Raman spectrum, X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), Atomic force microscope (AFM) and Scanning electron microscopy (SEM). The results indicate that the as-prepared graphene has a large size and few defects, and it is monolayer or less than three layers. The quality of graphene is significant improved compared to the reported electrochemical methods. The yield of graphene can reach 8.76% when the ratio of the H 2 O and NMP is 3:7. This method provides a potential solution for the recycling of waste lithium ion batteries. Copyright © 2017 Elsevier Inc. All rights reserved.

Thermal quantities of 46Ti

International Nuclear Information System (INIS)

Rahmatinejad, A.; Razavi, R.; Kakavand, T.

2015-01-01

Thermodynamic quantities of 46 Ti have been calculated in the framework of the BCS model with inclusion of modified nuclear pairing gap (MPBCS) that was proposed in our previous publication. Using modified paring gap results in an S-shaped heat capacity curve at critical temperature with a smooth behavior instead of singular behavior of the same curve in the BCS calculations. In addition the thermal quantities have been extracted within the framework of a canonical ensemble according to the new experimental data on nuclear level densities measured by the Oslo group. Comparison shows a good agreement between our calculations in MPBCS and the extracted quantities in the canonical ensemble framework

Preparation and provisional validation of a large size dried spike: Batch SAL-9934

International Nuclear Information System (INIS)

Jammet, G.; Zoigner, A.; Doubek, N.; Aigner, H.; Deron, S.; Bagliano, G.

1990-05-01

To determine uranium and plutonium concentration using isotope dilution mass spectrometry, weighed aliquands of a synthetic mixture containing about 2 mg of Pu (with a 239 Pu abundance of about 98%) and 40 mg of U (with a 235 U enrichment of about 19%) have been prepared and verified by SAL to be used to spike samples of concentrated spent fuel solutions with a high burn-up and a low 235 U enrichment. Certified Reference Materials Pu-NBL-126, natural U-NBS-960 and 93% enriched U-NBL-116 were used to prepare a stock solution containing 3.2 mg/ml of Pu and 64.3 mg/ml of 18.8% enriched U. Before shipment to the Reprocessing Plant, aliquands of the stock solution are dried to give Large Size Dried (LSD) Spikes which resist shocks encountered during transportation, so that they can readily be recovered quantitatively at the plant. This paper describes the preparation and the validation of a third batch of LSD-Spike which is intended to be used as a common spike by the plant operator, the national and the IAEA inspectorates. 6 refs, 6 tabs

Quantities for environmental monitoring

International Nuclear Information System (INIS)

1989-01-01

It is recommended that if measurements are made with the objective of monitor radiation levels in the environment to elucidate long-term changes in these levels, then air kerma should be used. If the objective is to give an indication that levels from man-made sources are acceptable within specified limits for the exposure of people, then ambient dose equivalent should be used. It should be noted that radiation risks to individuals are best expressed by the quantity effective dose equivalent. If this latter quantity is to be accurately assessed, it may be necessary to obtain details of the quality of the environmental radiation that cannot be described adequately by simple measurements of either air kerma or ambient dose equivalent. If the above objectives pertain, the measurements should record both air kerma and ambient dose equivalent. If neutrons are measured in the environment then ambient dose equivalent is the appropriate quantity for both the above objectives. (author)

Method and means for determining heat quantities

Energy Technology Data Exchange (ETDEWEB)

Waasdorp, G G; de Jong, J J; Bijl, A

1965-08-24

To determine the quantity of potential heat W that has flowed past a certain point in a certain time, the velocity of the combustible Q, the temperature T, and the specific gravity YDTU are measured, and these values are transmitted to a computer which automatically calculates the quantity: ..pi..EQUATION/sup -/ in which delta T is the difference between the combustible temperature T and a reference temperature, and in which the relation f(YDTU, delta T) represents the heat of combustion as a function of the quantities YDTU and delta T and possibly other properties of the combustible. Alternatively the quantity: ..pi..EQUATION/sup -/ may be measured; here the quantities have the same meaning as above.

Quantities of arsenic-treated wood in demolition debris generated by Hurricane Katrina.

Science.gov (United States)

Dubey, Brajesh; Solo-Gabriele, Helena M; Townsendt, Timothy G

2007-03-01

The disaster debris from Hurricane Katrina is one of the largest in terms of volume and economic loss in American history. One of the major components of the demolition debris is wood waste of which a significant proportion is treated with preservatives, including preservatives containing arsenic. As a result of the large scale destruction of treated wood structures such as electrical poles, fences, decks, and homes a considerable amount of treated wood and consequently arsenic will be disposed as disaster debris. In this study an effort was made to estimate the quantity of arsenic disposed through demolition debris generated in the Louisiana and Mississippi area through Hurricane Katrina. Of the 72 million cubic meters of disaster debris generated, roughly 12 million cubic meters were in the form of construction and demolition wood resulting in an estimated 1740 metric tons of arsenic disposed. Management of disaster debris should consider the relatively large quantities of arsenic associated with pressure-treated wood.

Preparing Urban School Leaders: What Works?

Science.gov (United States)

Huang, Tiedan; Beachum, Floyd D.; White, George P.; Kaimal, Girija; FitzGerald, Anne Marie; Reed, Peter

2012-01-01

Extant research, though limited in quantity, increasingly demonstrates the critical connection between quality preparation experience, candidates' leadership capacity, and their subsequent instructional and transformation leadership practices. Using mixed methods, this study builds on the current knowledge base and aims to further verify the link…

A Viewpoint on the Quantity "Plane Angle"

Science.gov (United States)

Eder, W. E.

1982-01-01

Properties of the quantity "plane angle" are explored under the hypothesis that it is a dimensional quantity. The exploration proceeds especially with respect to the physical concept, its mathematical treatment, vector concepts, measurement theory, units of related quantities, engineering pragmatism, and SI. An attempt is made to bring these different relations into a rational, logical and consistent framework, and thus to justify the hypothesis. Various types of vectorial quantities are recognized, and their properties described with an outline of the necessary algebraic manipulations. The concept of plane angle is amplified, and its interdependence with the circular arc is explored. The resulting units of plane angle form a class of similar scales of measurement. Consequences of the confirmed hypothesis are developed for mathematical expressions involving trigonometric functions, rotational volumes and areas, mathematical limits, differentiation and series expansion. Consequences for mechanical rotational quantities are developed, with proposals for revisions to a number of expressions for derived units within SI. A revised definition for the quantity "plane angle" is stated to take account of the developed insights. There is a clear need to reconsider the status of plane angle and some other quantities within the international framework of SI.

The regional service for the preparation and distribution of radiopharmaceuticals in the west of Scotland

International Nuclear Information System (INIS)

Horton, P.W.

1977-01-01

The centralised preparation of radiopharmaceuticals was begun in 1965 for reasons of radiological safety and cost effectiveness. It enabled the provision of a single specially designed facility to process large quantities of radioactivity safely and avoided the distributed handling of radioactivity. Effective supervision of the safe usage and disposal of radionuclides in hospitals throughout the region became practicable. It also enabled the bulk purchase of radiopharmaceuticals with lower unit costs and their efficient utilisation due to the large number of users. Since 1965, great changes have taken place in the nature of the common radiopharmaceuticals. Most now have short physical half-lives and must be prepared close to their place of use. This has meant improving the pharmaceutical standards of the facilities and working methods. However, the reasons stated above for a centralised service are still applicable and have been reinforced by others arising from the need for good pharmaceutical manufacturing practice in current radiopharmaceutical production

Emission sources and quantities

International Nuclear Information System (INIS)

Heinen, B.

1991-01-01

The paper examines emission sources and quantities for SO 2 and NO x . Natural SO 2 is released from volcanic sources and to a much lower extent from marsh gases. In nature NO x is mainly produced in the course of the chemical and bacterial denitrification processes going on in the soil. Manmade pollutants are produced in combustion processes. The paper concentrates on manmade pollution. Aspects discussed include: mechanism of pollution development; manmade emission sources (e.g. industry, traffic, power plants and domestic sources); and emission quantities and forecasts. 11 refs., 2 figs., 5 tabs

Consensus on items and quantities of clinical equipment required to deal with a mass casualties big bang incident: a national Delphi study.

Science.gov (United States)

Duncan, Edward A S; Colver, Keith; Dougall, Nadine; Swingler, Kevin; Stephenson, John; Abhyankar, Purva

2014-02-22

Major short-notice or sudden impact incidents, which result in a large number of casualties, are rare events. However health services must be prepared to respond to such events appropriately. In the United Kingdom (UK), a mass casualties incident is when the normal response of several National Health Service organizations to a major incident, has to be supported with extraordinary measures. Having the right type and quantity of clinical equipment is essential, but planning for such emergencies is challenging. To date, the equipment stored for such events has been selected on the basis of local clinical judgment and has evolved without an explicit evidence-base. This has resulted in considerable variations in the types and quantities of clinical equipment being stored in different locations. This study aimed to develop an expert consensus opinion of the essential items and minimum quantities of clinical equipment that is required to treat 100 people at the scene of a big bang mass casualties event. A three round modified Delphi study was conducted with 32 experts using a specifically developed web-based platform. Individuals were invited to participate if they had personal clinical experience of providing a pre-hospital emergency medical response to a mass casualties incident, or had responsibility in health emergency planning for mass casualties incidents and were in a position of authority within the sphere of emergency health planning. Each item's importance was measured on a 5-point Likert scale. The quantity of items required was measured numerically. Data were analyzed using nonparametric statistics. Experts achieved consensus on a total of 134 items (54%) on completion of the study. Experts did not reach consensus on 114 (46%) items. Median quantities and interquartile ranges of the items, and their recommended quantities were identified and are presented. This study is the first to produce an expert consensus on the items and quantities of clinical equipment

A Semi-Vectorization Algorithm to Synthesis of Gravitational Anomaly Quantities on the Earth

Science.gov (United States)

Abdollahzadeh, M.; Eshagh, M.; Najafi Alamdari, M.

2009-04-01

The Earth's gravitational potential can be expressed by the well-known spherical harmonic expansion. The computational time of summing up this expansion is an important practical issue which can be reduced by an efficient numerical algorithm. This paper proposes such a method for block-wise synthesizing the anomaly quantities on the Earth surface using vectorization. Fully-vectorization means transformation of the summations to the simple matrix and vector products. It is not a practical for the matrices with large dimensions. Here a semi-vectorization algorithm is proposed to avoid working with large vectors and matrices. It speeds up the computations by using one loop for the summation either on degrees or on orders. The former is a good option to synthesize the anomaly quantities on the Earth surface considering a digital elevation model (DEM). This approach is more efficient than the two-step method which computes the quantities on the reference ellipsoid and continues them upward to the Earth surface. The algorithm has been coded in MATLAB which synthesizes a global grid of 5′Ã- 5′ (corresponding 9 million points) of gravity anomaly or geoid height using a geopotential model to degree 360 in 10000 seconds by an ordinary computer with 2G RAM.

Separation of traces of traces of trans-plutonium elements in weight quantities of rare earths

International Nuclear Information System (INIS)

SORET, Christian

1969-08-01

The author reports the separation of trans-plutonium elements and their dosing in a mixture of fission products. In some situations dosing is performed on both rare earths and trans-plutonium elements. The chemical separation process is a chromatographic method of exchange on an anionic resin in concentrated lithium chloride. He proposes a brief overview of separation processes, describes the separation mechanism, and then reports preliminary studies of the influence of increasing quantities of rare earths and the influence of increasing heights of resin bed in order to determine the best conditions of separation. He describes the preparation of resin and of the column, the introduction of the fixing solution at the top of the column, the preparation of lithium chloride solutions. He presents the adjustment and measurement devices, and the calculation of the resin minimum volume. Results are then presented and discussed. The operation mode is addressed: devices, reagents, preparation techniques (preparation of lithium chloride solutions) [fr

Standard methods for sampling and sample preparation for gamma spectroscopy

International Nuclear Information System (INIS)

Taskaeva, M.; Taskaev, E.; Nikolov, P.

1993-01-01

The strategy for sampling and sample preparation is outlined: necessary number of samples; analysis and treatment of the results received; quantity of the analysed material according to the radionuclide concentrations and analytical methods; the minimal quantity and kind of the data needed for making final conclusions and decisions on the base of the results received. This strategy was tested in gamma spectroscopic analysis of radionuclide contamination of the region of Eleshnitsa Uranium Mines. The water samples was taken and stored according to the ASTM D 3370-82. The general sampling procedures were in conformity with the recommendations of ISO 5667. The radionuclides was concentrated by coprecipitation with iron hydroxide and ion exchange. The sampling of soil samples complied with the rules of ASTM C 998, and their sample preparation - with ASTM C 999. After preparation the samples were sealed hermetically and measured. (author)

Estimated quantities of residual materials in a KBS-3H repository at Olkiluoto

Energy Technology Data Exchange (ETDEWEB)

Hagros, Annika (Sannio and Riekkola OY (Finland))

2008-12-15

The quantities of residual materials in a KBS-3H type repository have been estimated in this report. The repository is assumed to be constructed at Olkiluoto in Eurajoki, Western Finland. Both the total quantities of the materials introduced into the repository and the quantities of materials that remain in the repository after closure have been calculated. The calculations are largely based on a similar work regarding the material quantities in the Finnish KBS-3V repository and the main goal has been to identify the differences between the KBS-3H and KBS-3V repositories with respect to the type and quantities of residual materials. As the design of the KBS-3H repository is not final yet, the results are only preliminary. Several alternative designs were assumed in the calculations, resulting in different total quantities of materials. The design alternatives that had the greatest effect on the total material quantities were the two different tunnel backfill options, bentonite-crushed rock and Friedland clay. If Friedland clay is used instead of a bentonite-crushed rock mixture, the total quantity of pyrite remaining in the repository is 20 times larger and the quantities of organic materials and gypsum are also increased significantly. The other design alternatives did not have a substantial effect on the total material quantities. The remaining quantity of cement can be reduced by some 20% by selecting the silica grouting alternative in the sealing of the rock mass and low-pH cement in the shotcreting of the repository, instead of using the ordinary cement alternatives. If the total quantity of steel should be minimised, the use of the DAWE design alternative would be better than the Basic Design, although the total reduction would be less than 10%. The main difference between the different drift end plug alternatives is related to the total remaining quantity of silica, which is some 80% smaller if the rock plug is used instead of the LHHP (Low Heat High

Estimated quantities of residual materials in a KBS-3H repository at Olkiluoto

International Nuclear Information System (INIS)

Hagros, Annika

2008-12-01

The quantities of residual materials in a KBS-3H type repository have been estimated in this report. The repository is assumed to be constructed at Olkiluoto in Eurajoki, Western Finland. Both the total quantities of the materials introduced into the repository and the quantities of materials that remain in the repository after closure have been calculated. The calculations are largely based on a similar work regarding the material quantities in the Finnish KBS-3V repository and the main goal has been to identify the differences between the KBS-3H and KBS-3V repositories with respect to the type and quantities of residual materials. As the design of the KBS-3H repository is not final yet, the results are only preliminary. Several alternative designs were assumed in the calculations, resulting in different total quantities of materials. The design alternatives that had the greatest effect on the total material quantities were the two different tunnel backfill options, bentonite-crushed rock and Friedland clay. If Friedland clay is used instead of a bentonite-crushed rock mixture, the total quantity of pyrite remaining in the repository is 20 times larger and the quantities of organic materials and gypsum are also increased significantly. The other design alternatives did not have a substantial effect on the total material quantities. The remaining quantity of cement can be reduced by some 20% by selecting the silica grouting alternative in the sealing of the rock mass and low-pH cement in the shotcreting of the repository, instead of using the ordinary cement alternatives. If the total quantity of steel should be minimised, the use of the DAWE design alternative would be better than the Basic Design, although the total reduction would be less than 10%. The main difference between the different drift end plug alternatives is related to the total remaining quantity of silica, which is some 80% smaller if the rock plug is used instead of the LHHP (Low Heat High

Precise and efficient evaluation of gravimetric quantities at arbitrarily scattered points in space

Science.gov (United States)

Ivanov, Kamen G.; Pavlis, Nikolaos K.; Petrushev, Pencho

2017-12-01

Gravimetric quantities are commonly represented in terms of high degree surface or solid spherical harmonics. After EGM2008, such expansions routinely extend to spherical harmonic degree 2190, which makes the computation of gravimetric quantities at a large number of arbitrarily scattered points in space using harmonic synthesis, a very computationally demanding process. We present here the development of an algorithm and its associated software for the efficient and precise evaluation of gravimetric quantities, represented in high degree solid spherical harmonics, at arbitrarily scattered points in the space exterior to the surface of the Earth. The new algorithm is based on representation of the quantities of interest in solid ellipsoidal harmonics and application of the tensor product trigonometric needlets. A FORTRAN implementation of this algorithm has been developed and extensively tested. The capabilities of the code are demonstrated using as examples the disturbing potential T, height anomaly ζ , gravity anomaly Δ g , gravity disturbance δ g , north-south deflection of the vertical ξ , east-west deflection of the vertical η , and the second radial derivative T_{rr} of the disturbing potential. After a pre-computational step that takes between 1 and 2 h per quantity, the current version of the software is capable of computing on a standard PC each of these quantities in the range from the surface of the Earth up to 544 km above that surface at speeds between 20,000 and 40,000 point evaluations per second, depending on the gravimetric quantity being evaluated, while the relative error does not exceed 10^{-6} and the memory (RAM) use is 9.3 GB.

Effects of Fuel Quantity on Soot Formation Process for Biomass-Based Renewable Diesel Fuel Combustion

KAUST Repository

Jing, Wei

2016-12-01

Soot formation process was investigated for biomass-based renewable diesel fuel, such as biomass to liquid (BTL), and conventional diesel combustion under varied fuel quantities injected into a constant volume combustion chamber. Soot measurement was implemented by two-color pyrometry under quiescent type diesel engine conditions (1000 K and 21% O2 concentration). Different fuel quantities, which correspond to different injection widths from 0.5 ms to 2 ms under constant injection pressure (1000 bar), were used to simulate different loads in engines. For a given fuel, soot temperature and KL factor show a different trend at initial stage for different fuel quantities, where a higher soot temperature can be found in a small fuel quantity case but a higher KL factor is observed in a large fuel quantity case generally. Another difference occurs at the end of combustion due to the termination of fuel injection. Additionally, BTL flame has a lower soot temperature, especially under a larger fuel quantity (2 ms injection width). Meanwhile, average soot level is lower for BTL flame, especially under a lower fuel quantity (0.5 ms injection width). BTL shows an overall low sooting behavior with low soot temperature compared to diesel, however, trade-off between soot level and soot temperature needs to be carefully selected when different loads are used.

Large reversible magnetostrictive effect of MnCoSi-based compounds prepared by high-magnetic-field solidification

Science.gov (United States)

Hu, Q. B.; Hu, Y.; Zhang, S.; Tang, W.; He, X. J.; Li, Z.; Cao, Q. Q.; Wang, D. H.; Du, Y. W.

2018-01-01

The MnCoSi compound is a potential magnetostriction material since the magnetic field can drive a metamagnetic transition from an antiferromagnetic phase to a high magnetization phase in it, which accompanies a large lattice distortion. However, a large driving magnetic field, magnetic hysteresis, and poor mechanical properties seriously hinder its application for magnetostriction. By substituting Fe for Mn and introducing vacancies of the Mn element, textured and dense Mn0.97Fe0.03CoSi and Mn0.88CoSi compounds are prepared through a high-magnetic-field solidification approach. As a result, large room-temperature and reversible magnetostriction effects are observed in these compounds at a low magnetic field. The origin of this large magnetostriction effect and potential applications are discussed.

Critical review of the current radiation protection quantities and units

International Nuclear Information System (INIS)

Sabol, J.

1998-01-01

Examples exist in dosimetry and radiation protection where primary attention was focused on the unit rather than the corresponding quantity. Another difficulty arises from the fact that quantities in this field cannot be considered as pure physical quantities, they are rather biophysical quantities. There are too many quantities (e. g. 17 quantities based on the dose equivalent), with differences in numerical values of 'similar' quantities, not always satisfactory approximations of virtually unmeasurable quantities by measurable quantities, inconsistency in definitions and interpretations of quantities of some international expert bodies, and problems of weighting and conversion factors. (M.D.)

36 CFR 223.220 - Quantity determination.

Science.gov (United States)

2010-07-01

... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Quantity determination. 223.220 Section 223.220 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE SALE AND DISPOSAL OF NATIONAL FOREST SYSTEM TIMBER Special Forest Products § 223.220 Quantity determination...

THE ANALYSIS OF THE SEWAGE QUANTITY DISCHARGING FROM THE SEWERAGE AGGLOMERATION IN SANOK

Directory of Open Access Journals (Sweden)

Anna Młyńska

2017-06-01

Full Text Available Both too large and too small volume of sewage inflowing to wastewater treatment plant in relation to its volume determined during designing process, can contribute to the reduction of sewage treatment effectiveness. Taking into consideration, in this article, the analysis of the sewage quantity discharging from the Sanok agglomeration and treated in domestic wastewater treatment plant in 2013-2015 was performed. The analysis indicated that in each year of the analyzed period, to the Wastewater Treatment Plant in Trepcza, a similar volumes of sewage was inflowing and the maximum hydraulic capacity of the object was not exceeded, what is evidenced by the average daily sewage flow values. It is noted that in rainless periods, the quantities of inflowing sewage were smaller than during days with wet weather. Despite of periodically situations of the hydraulic overload and hydraulic underload, it can be stated that the effectiveness of the sewage treatment processes is not endangered by the excessive or insufficient quantities of inflowing sewage.

EOQ Model for Deteriorating Items with exponential time dependent Demand Rate under inflation when Supplier Credit Linked to Order Quantity

Directory of Open Access Journals (Sweden)

Rakesh Prakash Tripathi

2014-05-01

Full Text Available In paper (2004 Chang studied an inventory model under a situation in which the supplier provides the purchaser with a permissible delay of payments if the purchaser orders a large quantity. Tripathi (2011 also studied an inventory model with time dependent demand rate under which the supplier provides the purchaser with a permissible delay in payments. This paper is motivated by Chang (2004 and Tripathi (2011 paper extending their model for exponential time dependent demand rate. This study develops an inventory model under which the vendor provides the purchaser with a credit period; if the purchaser orders large quantity. In this chapter, demand rate is taken as exponential time dependent. Shortages are not allowed and effect of the inflation rate has been discussed. We establish an inventory model for deteriorating items if the order quantity is greater than or equal to a predetermined quantity. We then obtain optimal solution for finding optimal order quantity, optimal cycle time and optimal total relevant cost. Numerical examples are given for all different cases. Sensitivity of the variation of different parameters on the optimal solution is also discussed. Mathematica 7 software is used for finding numerical examples.

Optimized Gen-II FeCrAl cladding production in large quantity for campaign testing

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, Yukinori [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Sun, Zhiqian [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Pint, Bruce A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Terrani, Kurt A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2016-06-03

There are two major objectives in this report; (1) to optimize microstructure control of ATF FeCrAl alloys during tube drawing processes, and (2) to provide an update on the progress of ATF FeCrAl tube production via commercial manufacturers. Experimental efforts have been made to optimize the process parameters balancing the tube fabricability, especially for tube drawing processes, and microstructure control of the final tube products. Lab-scale sheet materials of Gen II FeCrAl alloys (Mo-containing and Nb-containing FeCrAl alloys) were used in the study, combined with a stepwise warm-rolling process and intermediate annealing, aiming to simulate the tube drawing process in a commercial tube manufacturer. The intermediate annealing at 650ºC for 1h was suggested for the tube-drawing process of Mo-containing FeCrAl alloys because it successfully softened the material by recovering the work hardening introduced through the rolling step, without inducing grain coarsening due to recrystallization. The final tube product is expected to have stabilized deformed microstructure providing the improved tensile properties with sufficient ductility. Optimization efforts on Nb-containing FeCrAl alloys focused on the effect of alloying additions and annealing conditions on the stability of deformed microstructure. Relationships between the second-phase precipitates (Fe₂Nb-Laves phase) and microstructure stability are discussed. FeCrAl tube production through commercial tube manufacturers is currently in progress. Three different manufacturers, Century Tubes, Inc. (CTI), Rhenium Alloys, Inc. (RAI), and Superior Tube Company, Inc. (STC), are providing capabilities for cold-drawing, warm-drawing, and HPTR cold-pilgering, respectively. The first two companies are currently working on large quantity tube production (expected 250 ft length) of Gen I model FeCrAl alloy (B136Y3, at CTI) and Gen II (C35M4, at RAI), with the process parameters obtained from the experimental

[Application of target restoration space quantity and quantitative relation in precise esthetic prosthodontics].

Science.gov (United States)

Haiyang, Yu; Tian, Luo

2016-06-01

Target restoration space (TRS) is the most precise space required for designing optimal prosthesis. TRS consists of an internal or external tooth space to confirm the esthetics and function of the final restoration. Therefore, assisted with quantitive analysis transfer, TRS quantitative analysis is a significant improvement for minimum tooth preparation. This article presents TRS quantity-related measurement, analysis, transfer, and internal relevance of three TR. classifications. Results reveal the close bond between precision and minimally invasive treatment. This study can be used to improve the comprehension and execution of precise esthetic prosthodontics.

Conceptual Model of Quantities, Units, Dimensions, and Values

Science.gov (United States)

Rouquette, Nicolas F.; DeKoenig, Hans-Peter; Burkhart, Roger; Espinoza, Huascar

2011-01-01

JPL collaborated with experts from industry and other organizations to develop a conceptual model of quantities, units, dimensions, and values based on the current work of the ISO 80000 committee revising the International System of Units & Quantities based on the International Vocabulary of Metrology (VIM). By providing support for ISO 80000 in SysML via the International Vocabulary of Metrology (VIM), this conceptual model provides, for the first time, a standard-based approach for addressing issues of unit coherence and dimensional analysis into the practice of systems engineering with SysML-based tools. This conceptual model provides support for two kinds of analyses specified in the International Vocabulary of Metrology (VIM): coherence of units as well as of systems of units, and dimension analysis of systems of quantities. To provide a solid and stable foundation, the model for defining quantities, units, dimensions, and values in SysML is explicitly based on the concepts defined in VIM. At the same time, the model library is designed in such a way that extensions to the ISQ (International System of Quantities) and SI Units (Systeme International d Unites) can be represented, as well as any alternative systems of quantities and units. The model library can be used to support SysML user models in various ways. A simple approach is to define and document libraries of reusable systems of units and quantities for reuse across multiple projects, and to link units and quantity kinds from these libraries to Unit and QuantityKind stereotypes defined in SysML user models.

Concept of ICRU's operational quantity and its application

International Nuclear Information System (INIS)

Murakami, Hiroyuki

1995-01-01

The operational quantity which was introduced in the ICRU report 39 published in 1985 was shocking rather than fresh for the author. The report was translated into Japanese, but at the beginning, the contents were not able to be understood. Thereafter, the measurement of ICRU sphere dose equivalent was introduced in a national law. But it is feared that the understanding of this operational quantity is limited to specialist level, and is not by men of practical works. The meaning of ''operational'' must be that workers measure and obtain dose on the spot for the radiation protection for themselves. The principles used when ICRU considered the new practical measured quantity are shown. In the definition of operational quantity in area monitoring, two concepts of expanded and aligned connect real measurement with the operational quantity. The problems of measuring individual dose equivalent are discussed. As to the reality of applying the operational quantity, the fundamentals of the calibration of measuring instruments, the investigation of the operational quantity in relation to measuring instruments and measurement mode, and the relation of area monitoring and individual monitoring are described. (K.I.)

Tritium concentrations in natural waters in Japan before use of a large quantity of tritium on its fusion program

International Nuclear Information System (INIS)

Kaji, Toshio; Momoshima, Noriyuki; Takashima, Yoshimasa.

1989-01-01

To clarify environmental tritium levels in Japan before use of a large quantity of tritium on its fusion program, the authors analyzed the tritium concentrations in various water samples, such as rain, river, lake, coastal sea and deep sea waters in Japan. The tritium concentrations in rain water were high at higher latitude. The definite differences of the tritium concentrations due to the weather conditions or seasons were not observed. The average tritium concentration in river water was 51.5 pCi/l in 1982 and that in lake water was 63.5 pCi/l in 1983. The vertical profiles of the tritium concentrations in the representative lakes were almost homogeneous except surface water. The average tritium concentrations in coastal seawater were about 20 pCi/l in both 1982 and 1983. The tendency of the increased tritium level with latitude as reported in literature was not observed by these experiments. Tritium levels in natural water in small isolated islands were lower than those at other places. In the Japan Sea, it was recognized that tritium was distributed down to around 2000 m in depth. This means that the more active vertical mixing of water masses than that in the Pacific Ocean is taking place. (author)

30 CFR 75.325 - Air quantity.

Science.gov (United States)

2010-07-01

... the exposure of miners. (i) A ventilating air quantity that is less than what is required by paragraph... results of sampling that demonstrate that the lesser air quantity will maintain continuous compliance with applicable TLV ®'s. (j) If during sampling required by § 70.1900(c) of this subchapter the ventilating air is...

Dose rate constants for new dose quantities

International Nuclear Information System (INIS)

Tschurlovits, M.; Daverda, G.; Leitner, A.

1992-01-01

Conceptual changes and new quantities made is necessary to reassess dose rate quantities. Calculations of the dose rate constant were done for air kerma, ambient dose equivalent and directional dose equivalent. The number of radionuclides is more than 200. The threshold energy is selected as 20 keV for the dose equivalent constants. The dose rate constant for the photon equivalent dose as used mainly in German speaking countries as a temporary quantity is also included. (Author)

Review on Quantity of Hexanediol Diacrylate (HDDA) Used as Sensitizer in Production of Radiation Pre vulcanized Natural Rubber Latex (RVNRL)

International Nuclear Information System (INIS)

Sofian Ibrahim; Syuhada Ramli; Mohd Noorwadi Mat Lazim

2016-01-01

One of the main factors that caused RVNRL failed to be marketed widely is lack of mechanical properties; low tensile strength (about 20 MPa). In these experiments, the quantity of Hexanediol diacrylate (HDDA) used in the preparation RVNRL was revised in order to improve the mechanical properties RVNRL. (author)

Isolation and preparation of 3H-tetrandrine

International Nuclear Information System (INIS)

Xunyang Huang; Yin Wang; Zangde Lu

1994-01-01

Tetrandrine is a bisbenzytehahydroisoquinoline alkaloid. Its structure is very complex and the preparation of labeled derivatives is difficult. We have prepared 3 H-tetrandrine using the tritium gas exposure method. This method produces many fragments which make isolation and purification of small quantities difficult. We investigated these fragments of unlabeled d-tetrandrine and found almost all contain one to several hydroxide groups. Using this information, we designed a two-step paper chromatography method for isolation and purification citric acid buffer to the paper to block the migration of hydroxide group fragments of tetrandrine. 3 H-tetrandrine was successfully prepared with a radiochemical purity of 90%. (author)

Automated spike preparation system for Isotope Dilution Mass Spectrometry (IDMS)

International Nuclear Information System (INIS)

Maxwell, S.L. III; Clark, J.P.

1990-01-01

Isotope Dilution Mass Spectrometry (IDMS) is a method frequently employed to measure dissolved, irradiated nuclear materials. A known quantity of a unique isotope of the element to be measured (referred to as the ''spike'') is added to the solution containing the analyte. The resulting solution is chemically purified then analyzed by mass spectrometry. By measuring the magnitude of the response for each isotope and the response for the ''unique spike'' then relating this to the known quantity of the ''spike'', the quantity of the nuclear material can be determined. An automated spike preparation system was developed at the Savannah River Site (SRS) to dispense spikes for use in IDMS analytical methods. Prior to this development, technicians weighed each individual spike manually to achieve the accuracy required. This procedure was time-consuming and subjected the master stock solution to evaporation. The new system employs a high precision SMI Model 300 Unipump dispenser interfaced with an electronic balance and a portable Epson HX-20 notebook computer to automate spike preparation

7 CFR 61.102 - Determination of quantity index.

Science.gov (United States)

2010-01-01

... the quantity index shall equal four times percentage of oil plus six times percentage of ammonia, plus 5. (b) For American Pima cottonseed the quantity index shall equal four times percentage of oil... 7 Agriculture 3 2010-01-01 2010-01-01 false Determination of quantity index. 61.102 Section 61.102...

The Acquisition of Quantity Contrasts in Guina-ang Bontok

Science.gov (United States)

Aoyama, Katsura; Reid, Lawrence A.

2016-01-01

This study reports on the acquisition of quantity contrasts in Guina-ang Bontok, an indigenous language spoken in the Philippines. Four-year-old and 5-year-old children's perception and production of quantity contrasts were examined using a pair of names that contrast in the quantity of the medial nasal. Frequencies of the quantity contrast were…

Preparation of standard hair material and development of analytical methodology

International Nuclear Information System (INIS)

Gangadharan, S.; Ganapathi Iyer, S.; Ali, M.M.; Thantry, S.S.; Verma, R.; Arunachalam, J.; Walvekar, A.P.

1992-01-01

In 1976 Indian Researchers suggested the possible use of hair as an indicator of environmental exposure and established through a study of country wide student population and general population of the metropolitan city of Bombay that human scalp hair could indeed be an effective first level monitor in a scheme of multilevel monitoring of environmental exposure to inorganic pollutants. It was in this context and in view of the ready availability of large quantities of scalp hair subjected to minimum treatment by chemicals that they proposed to participate in the preparation of a standard material of hair. It was also recognized that measurements of trace element concentrations at very low levels require cross-validation by different analytical techniques, even within the same laboratory. The programme of work that has been carried out since the first meeting of the CRP had been aimed at these two objectives. These objectives include the preparation of standard material of hair and the development of analytical methodologies for determination of elements and species of interest. 1 refs., 3 tabs

Quantities used in radiological protection

International Nuclear Information System (INIS)

Menossi, Carlos

2010-01-01

The application of ICRP recommendations requires knowledge of a variety of concepts and magnitudes. Many of them are employed in other fields of science and precision in its definition reflects this wide application. In this regard, information on quantities and basic units of radiation, which exists in numerous publications, are subjects of great interest. The characteristics and radiation effects are studied by physicists, biologists and chemists mainly. However, there are basics that must be known and to be recognized by general practitioners and specialists from all branches of medicine. The information on quantities and units are used only in radiation protection, have been obtained from the reports listed on the attached bibliography. Such quantities and units contain weighting factors used to provide for different types of radiation and energies that affect the body and thus take into account the relative radio-sensitivity of different tissues. Additionally, they have added a series of data for a better understanding of the units: for example, multiples and sub-multiples, and some examples of converting the units used in radiation protection. (author) [es

Quantity and quality benefits of in-service invasive cleaning of trunk mains

Directory of Open Access Journals (Sweden)

I. Sunny

2017-07-01

Full Text Available Trunk mains are high risk critical infrastructure where poor performance can impact on large numbers of customers. Both quantity (e.g. hydraulic capacity and quality (e.g. discolouration of trunk main performance are affected by asset deterioration in the form of particle accumulation at the pipe wall. Trunk main cleaning techniques are therefore desirable to remove such material. However, little is quantified regarding the efficacy of different maintenance interventions or longer-term changes following such cleaning. This paper presents an assessment of quantity and quality performance of a trunk main system pre, post and for 12 months following cleaning using pigging with ice slurry. Hydraulic calibration showed a 7 times roughness height reduction after ice slurry pigging, evidencing substantially improved hydraulic capacity and reduced headloss. Turbidity response due to carefully imposed shear stress increase remained significant after the cleaning intervention, showing that relatively loose material had not been fully removed from the pipe wall. Overall the results demonstrate that cleaning by pigging with ice slurry can be beneficial for quantity performance, but care and further assessment may be necessary to realise the full quality benefits.

Quantity and quality benefits of in-service invasive cleaning of trunk mains

Science.gov (United States)

Sunny, Iftekhar; Husband, Stewart; Drake, Nick; Mckenzie, Kevan; Boxall, Joby

2017-07-01

Trunk mains are high risk critical infrastructure where poor performance can impact on large numbers of customers. Both quantity (e.g. hydraulic capacity) and quality (e.g. discolouration) of trunk main performance are affected by asset deterioration in the form of particle accumulation at the pipe wall. Trunk main cleaning techniques are therefore desirable to remove such material. However, little is quantified regarding the efficacy of different maintenance interventions or longer-term changes following such cleaning. This paper presents an assessment of quantity and quality performance of a trunk main system pre, post and for 12 months following cleaning using pigging with ice slurry. Hydraulic calibration showed a 7 times roughness height reduction after ice slurry pigging, evidencing substantially improved hydraulic capacity and reduced headloss. Turbidity response due to carefully imposed shear stress increase remained significant after the cleaning intervention, showing that relatively loose material had not been fully removed from the pipe wall. Overall the results demonstrate that cleaning by pigging with ice slurry can be beneficial for quantity performance, but care and further assessment may be necessary to realise the full quality benefits.

48 CFR 916.504 - Indefinite-quantity contracts.

Science.gov (United States)

2010-10-01

... indefinite-quantity, multiple award contracts to ensure that adequate consideration exists to contractually... contracts. 916.504 Section 916.504 Federal Acquisition Regulations System DEPARTMENT OF ENERGY CONTRACTING METHODS AND CONTRACT TYPES TYPES OF CONTRACTS Indefinite-Delivery Contracts 916.504 Indefinite-quantity...

Preparation to exceptional operations

International Nuclear Information System (INIS)

Sort, M.

1984-01-01

Preparation to special maintenance operations requires a specific approach according to the considered intervention type. Replacement of vapor generators is representative of a kind of intervention where technics is generally only an adaptation to the power plant context of processes already in application in construction, and where methodology, planning and organization have an important role because of the variety and the quantity of taskworks to be done, the involved manpower, the dosimetry and time lag requirements [fr

The Third International Reference Preparation of Egg Lecithin

Science.gov (United States)

Krag, P.; Bentzon, M. Weis

1961-01-01

The Third International Reference Preparation of Egg Lecithin was produced (in a quantity of 5000 ml) at the WHO Serological Reference Centre, Copenhagen, and assayed in 1958 against the Second International Reference Preparation by four laboratories in three countries. Complement-fixation and slide-flocculation tests were used. The new preparation was found acceptable, and its establishment was authorized by the WHO Expert Committee on Biological Standardization. The average log10 titres and results of analyses of variances are shown. The variances were of the usual order of magnitude, and the differences in titre between antigens containing the Second and the Third International Reference Preparations varied from -0.011 to 0.116; only one of the differences exceeded the 5% limit of significance. The use of the Third International Reference Preparation in tests for the acceptability of lecithin preparations is described. PMID:13753864

The covariance matrix of derived quantities and their combination

International Nuclear Information System (INIS)

Zhao, Z.; Perey, F.G.

1992-06-01

The covariance matrix of quantities derived from measured data via nonlinear relations are only approximate since they are functions of the measured data taken as estimates for the true values of the measured quantities. The evaluation of such derived quantities entails new estimates for the true values of the measured quantities and consequently implies a modification of the covariance matrix of the derived quantities that was used in the evaluation process. Failure to recognize such an implication can lead to inconsistencies between the results of different evaluation strategies. In this report we show that an iterative procedure can eliminate such inconsistencies

Continuing Professional Development in the quantity surveying ...

African Journals Online (AJOL)

1991-01-01

Jan 1, 1991 ... The research established that quantity surveyors regarded handing in their CPD ... Surveying, Walter Sisulu University, PO Box 1421, East London, 5200, South Africa. ... Keywords: Continuing professional development, quantity surveying, perception .... In spite of this opportunity enshrined in the Act, the.

Method of preparing radionuclide doses

International Nuclear Information System (INIS)

Kuperus, J.H.

1987-01-01

A method is described of preparing aliquot dosea of a tracer material useful in diagnostic nuclear medicine comprising: storing discrete quantities of a lyophilized radionuclide carrier in separate tubular containers from which air and moisture is excluded, selecting from the tubular containers a container in which is stored a carrier appropriate for a nuclear diagnostic test to be performed, interposing the selected container between the needle and the barrel of a hypodermic syringe, and drawing a predetermined amount of a liquid containing a radionuclide tracer in known concentration into the hypodermic syringe barrel through the hypodermic needle and through the selected container to dissolve the discrete quantity of lyophilized carrier therein to combine the carrier with the radionuclide tracer to form an aliquot dose of nuclear diagnostic tracer material, as needed

Continuing Professional Development in the quantity surveying ...

African Journals Online (AJOL)

This research study was conducted in order to investigate Continuing Professional Development (CPD) in the South African quantity surveying profession. The study further aimed to establish the reasons why some quantity surveyors do not acquire the required CPD hours and face losing their professional registration with ...

Hypergraph topological quantities for tagged social networks

Science.gov (United States)

Zlatić, Vinko; Ghoshal, Gourab; Caldarelli, Guido

2009-09-01

Recent years have witnessed the emergence of a new class of social networks, which require us to move beyond previously employed representations of complex graph structures. A notable example is that of the folksonomy, an online process where users collaboratively employ tags to resources to impart structure to an otherwise undifferentiated database. In a recent paper, we proposed a mathematical model that represents these structures as tripartite hypergraphs and defined basic topological quantities of interest. In this paper, we extend our model by defining additional quantities such as edge distributions, vertex similarity and correlations as well as clustering. We then empirically measure these quantities on two real life folksonomies, the popular online photo sharing site Flickr and the bookmarking site CiteULike. We find that these systems share similar qualitative features with the majority of complex networks that have been previously studied. We propose that the quantities and methodology described here can be used as a standard tool in measuring the structure of tagged networks.

Mentoring: A New Approach to Geography Teacher Preparation

Science.gov (United States)

Bednarz, Sarah Witham; Bockenhauer, Mark H.; Walk, Fred H.

2005-01-01

Geography teacher preparation is an ongoing problem for the discipline. Changes in certification requirements and federal and state educational policies have diminished the role of colleges and universities in educating teachers. At the same time, geography education reform efforts have resulted in higher standards and an increased quantity of…

Isolation and preparation of [sup 3]H-tetrandrine

Energy Technology Data Exchange (ETDEWEB)

Xunyang Huang; Yin Wang; Zangde Lu (Institute of the Pharmaceutic Industry, Shanghai, SH (China). Div. of Chemistry)

1994-10-01

Tetrandrine is a bisbenzytehahydroisoquinoline alkaloid. Its structure is very complex and the preparation of labeled derivatives is difficult. We have prepared [sup 3]H-tetrandrine using the tritium gas exposure method. This method produces many fragments which make isolation and purification of small quantities difficult. We investigated these fragments of unlabeled d-tetrandrine and found almost all contain one to several hydroxide groups. Using this information, we designed a two-step paper chromatography method for isolation and purification citric acid buffer to the paper to block the migration of hydroxide group fragments of tetrandrine. [sup 3]H-tetrandrine was successfully prepared with a radiochemical purity of 90%. (author).

Large number discrimination in newborn fish.

Directory of Open Access Journals (Sweden)

Laura Piffer

Full Text Available Quantitative abilities have been reported in a wide range of species, including fish. Recent studies have shown that adult guppies (Poecilia reticulata can spontaneously select the larger number of conspecifics. In particular the evidence collected in literature suggest the existence of two distinct systems of number representation: a precise system up to 4 units, and an approximate system for larger numbers. Spontaneous numerical abilities, however, seem to be limited to 4 units at birth and it is currently unclear whether or not the large number system is absent during the first days of life. In the present study, we investigated whether newborn guppies can be trained to discriminate between large quantities. Subjects were required to discriminate between groups of dots with a 0.50 ratio (e.g., 7 vs. 14 in order to obtain a food reward. To dissociate the roles of number and continuous quantities that co-vary with numerical information (such as cumulative surface area, space and density, three different experiments were set up: in Exp. 1 number and continuous quantities were simultaneously available. In Exp. 2 we controlled for continuous quantities and only numerical information was available; in Exp. 3 numerical information was made irrelevant and only continuous quantities were available. Subjects successfully solved the tasks in Exp. 1 and 2, providing the first evidence of large number discrimination in newborn fish. No discrimination was found in experiment 3, meaning that number acuity is better than spatial acuity. A comparison with the onset of numerical abilities observed in shoal-choice tests suggests that training procedures can promote the development of numerical abilities in guppies.

Remarks and suggestions concerned with formulation of the definition of quantity ''committed dose'' and quantity ''radiation burden'' useful in estimates of population exposure

International Nuclear Information System (INIS)

Cwik, T.

1990-01-01

The paper contains remarks to the definitions of the quantity ''commited dose'' given in the publications of the ICRP. The suggestions are presented on the mode of formulating the definition of the quantity ''commited dose'' and the definition of the quantity denoted hitherto by the symbol H 50 . The other suggestions deal with introduction of the quantity ''radiation burden'', assigned for use in assessments of irradiation expressed ''per caput'' of population. 9 refs. (author)

Large-scale uniform bilayer graphene prepared by vacuum graphitization of 6H-SiC(0001) substrates

Science.gov (United States)

Wang, Qingyan; Zhang, Wenhao; Wang, Lili; He, Ke; Ma, Xucun; Xue, Qikun

2013-03-01

We report on the preparation of large-scale uniform bilayer graphenes on nominally flat Si-polar 6H-SiC(0001) substrates by flash annealing in ultrahigh vacuum. The resulting graphenes have a single thickness of one bilayer and consist of regular terraces separated by the triple SiC bilayer steps on the 6H-SiC(0001) substrates. In situ scanning tunneling microscopy reveals that suppression of pit formation on terraces and uniformity of SiC decomposition at step edges are the key factors to the uniform thickness. By studying the surface morphologies prepared under different annealing rates, it is found that the annealing rate is directly related to SiC decomposition, diffusion of the released Si/C atoms and strain relaxation, which together determine the final step structure and density of defects.

Virtual neutron scattering experiments - Training and preparing students for large-scale facility experiments

Directory of Open Access Journals (Sweden)

Julie Hougaard Overgaard

2016-11-01

Full Text Available Dansk Vi beskriver, hvordan virtuelle eksperimenter kan udnyttes i et læringsdesign ved at forberede de studerende til hands-on-eksperimenter ved storskalafaciliteter. Vi illustrerer designet ved at vise, hvordan virtuelle eksperimenter bruges på Niels Bohr Institutets kandidatkursus om neutronspredning. I den sidste uge af kurset, rejser studerende til et storskala neutronspredningsfacilitet for at udføre neutronspredningseksperimenter. Vi bruger studerendes udsagn om deres oplevelser til at argumentere for, at arbejdet med virtuelle experimenter forbereder de studerende til at engagere sig mere frugtbart med eksperimenter ved at lade dem fokusere på fysikken og relevante data i stedet for instrumenternes funktion. Vi hævder, at det er, fordi de kan overføre deres erfaringer med virtuelle eksperimenter til rigtige eksperimenter. Vi finder dog, at læring stadig er situeret i den forstand, at kun kendskab til bestemte eksperimenter overføres. Vi afslutter med at diskutere de muligheder, som virtuelle eksperimenter giver. English We describe how virtual experiments can be utilized in a learning design that prepares students for hands-on experiments at large-scale facilities. We illustrate the design by showing how virtual experiments are used at the Niels Bohr Institute in a master level course on neutron scattering. In the last week of the course, students travel to a large-scale neutron scattering facility to perform real neutron scattering experiments. Through student interviews and survey answers, we argue, that the virtual training prepares the students to engage more fruitfully with experiments by letting them focus on physics and data rather than the overwhelming instrumentation. We argue that this is because they can transfer their virtual experimental experience to the real-life situation. However, we also find that learning is still situated in the sense that only knowledge of particular experiments is transferred. We proceed to

41 CFR 101-27.102 - Economic order quantity principle.

Science.gov (United States)

2010-07-01

... MANAGEMENT 27.1-Stock Replenishment § 101-27.102 Economic order quantity principle. The economic order quantity (EOQ) principle is a means for achieving economical inventory management. Application of the EOQ... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Economic order quantity...

Results of the regional intercomparison exercise for the determination of operational quantity Hp(10) in Latin America

International Nuclear Information System (INIS)

Saravi, M.; Zaretzky, A.; Lindner, C.; Diaz, J.; Walwyn, G.; Amorim, R.; De Souza, D.; Gregori, B.; Papadopulos, S.; Meghzifene, A.; Ferruz, P.; Suarez, R. C.

2007-01-01

Several intercomparison exercises were organised by the International Atomic Energy Agency (IAEA) on the determination of operational quantities at the regional or inter-regional basis. In the Latin American region an intercomparison for the determination of the operational quantity H p (10) was completed mid-2004, as a follow-up to previous exercises carried out during the 1990's. Eighteen individual external monitoring services from nineteen Member States participated in the first phase. The second phase grouped 15 services that had participated in the first phase. Dosemeter irradiations in photon beams were done by four Secondary Standard Dosimetry Laboratories (SSDLs) of the region. The preparation of this exercises involved an audit by the IAEA SSDL, where reference irradiations were provided to all participants for verification of their systems. During the first phase (2002-2003) only 9 out of 18 services met the performance requirements for such monitoring services. Necessary corrective actions and procedure verification were implemented. During the second phase (2004) 11 out of 15 services fulfilled the performance criteria. This intercomparison shows that there has been improvement in the second phase and most participants demonstrated a satisfactory performance of the quantity tested. (authors)

Relevance of protection quantities in medical exposures

International Nuclear Information System (INIS)

Pradhan, A.S.

2008-01-01

International Commission on Radiological Protection (ICRP) continues to classify the exposures to radiation in three categories; namely 1- occupational exposure, 2- public exposure, and 3- medical exposure. Protection quantities are primarily meant for the regulatory purpose in radiological protection for controlling and limiting stochastic risks in occupational and public exposures. These are based on two basic assumptions of 1- linear no-threshold dose-effect relationship (LNT) at low doses and 2- long-term additivity of low doses. Medical exposure are predominantly delivered to individuals (patients) undergoing diagnostic examinations, interventional procedures and radiation therapy but also include individual caring for or comforting patients incurring exposure and the volunteers of biomedical medical research programmes. Radiation protection is as relevant to occupational and public exposure as to medical exposures except that the dose limits set for the formers are not applicable to medical exposure but reference levels and dose constrains are recommended for diagnostic and interventional medical procedures. In medical institutions, both the occupational and medical exposure takes place. Since the doses in diagnostic examinations are low, it has been observed that not only the protection quantities are often used in such cases but these are extended to estimate the number of cancer deaths due to such practices. One of the striking features of the new ICRP recommendations has been to elaborate the concepts of the dosimetric quantities. The limitation of protection quantities ((Effective dose, E=Σ RT D TR .W T .W R and Equivalent Dose H T =Σ RT D TR .W R ) have been brought out and this has raised a great concern and initiated debates on the use of these quantities in medical exposures. Consequently, ICRP has set a task group to provide more details and the recommendations. It has, therefore, became important to draw the attention of medical physics community

Large-scale preparation of active caspase-3 in E. coli by designing its thrombin-activatable precursors

Directory of Open Access Journals (Sweden)

Park Sung

2008-12-01

Full Text Available Abstract Background Caspase-3, a principal apoptotic effector that cleaves the majority of cellular substrates, is an important medicinal target for the treatment of cancers and neurodegenerative diseases. Large amounts of the protein are required for drug discovery research. However, previous efforts to express the full-length caspase-3 gene in E. coli have been unsuccessful. Results Overproducers of thrombin-activatable full-length caspase-3 precursors were prepared by engineering the auto-activation sites of caspase-3 precursor into a sequence susceptible to thrombin hydrolysis. The engineered precursors were highly expressed as soluble proteins in E. coli and easily purified by affinity chromatography, to levels of 10–15 mg from 1 L of E. coli culture, and readily activated by thrombin digestion. Kinetic evaluation disclosed that thrombin digestion enhanced catalytic activity (kcat/KM of the precursor proteins by two orders of magnitude. Conclusion A novel method for a large-scale preparation of active caspase-3 was developed by a strategic engineering to lack auto-activation during expression with amino acid sequences susceptible to thrombin, facilitating high-level expression in E. coli. The precursor protein was easily purified and activated through specific cleavage at the engineered sites by thrombin, generating active caspase-3 in high yields.

Physical quantities, their role and treatment in gasflow measurement techniques

International Nuclear Information System (INIS)

Narjes, L.

1977-06-01

We begin by taking a closer look at the concepts physical quantity, dimension and unit of measurement. Then a survey is given of the physical quantities applied in gasflow measurement techniques. Here the volume-, as well as the mass-flow rate, as derived quantities are of particular interest. The application of these quantities in relation to the legal units of measurement is specifically described. In addition the quantity equation and further the quantity equation adapted to the use of suitable units and their modes of application are compared. In the appendix four examples clarify these modes. Special attention is paid to the quantity equation adapted to practically oriented units. The applications of this type of equation in VDI regulations, standards and other technical guidelines for measurement of flow are mentioned. Moreover, the meaning of the standard state for the comparison of flows of gaseous fluids is illustrated. The difficulties concerning an international agreement on uniform standard temperature are explained. Starting from there, the advantages of the fundamental quantity 'amount of substance' applied to the measurement of flow are described. The use of this quantity for the thermodynamic state of ideal and real gases, respectively gas mixtures, is demonstrated in the appendix by an example. (orig.) [de

The influence of using anticoagulants (EDTA and citrate acid 3.8% toward the quantity of Platelet Rich Plasma (PRP

Directory of Open Access Journals (Sweden)

Lilies Anggarwati Astuti

2016-06-01

Full Text Available Platelet Rich Plasma (PRP is a blood concentrate that has a thrombocytes concentration several time higher than normal concentration of thrombocytes in normal human blood. PRP is a promising alternative to surgery with a safe and natural healing. The standard protocol for PRP preparation must be determined to get the right quantity and quality of the matrix of fibrin, leukocytes, platelets and growth factors. It could not be separated from the number of PRP produced. The use of PRP in the success of periodontal treatment would not be separated from methods to obtain it. To detect the influence of using anticoagulants (EDTA and citrate acid 3.8% toward the quantity of PRP. There are 41 subjects studied by taking 21 ml of venous blood in each of the seven tubes. Centrifugation performed twice with different speed, duration, use of anticoagulants then analyzed. This quantity between the two groups differed significantly between the PRP in EDTA group is higher 322.2 ml rather than citrate acid 3.8% group, then control group is higher 329.5 ml rather than citrate acid 3.8% group, while there is no difference between EDTA and control group. There is effect of the use of anticoagulants EDTA compared with citrate acid 3.8% in the quantity of PRP, and there was no effect using citrate acid 3.8% as anticoagulants in quantity of PRP.

Discounting of quantity surveying fees in South Africa

African Journals Online (AJOL)

by clients have forced Quantity Surveying firms into competition with ... Furthermore, 43% of consulting engineering firms were discounting their fees at a rate of .... Quantity. Surveying services are also offered in the fields of dispute resolution,.

New quantities in radiation protection and conversion coefficients

International Nuclear Information System (INIS)

1986-01-01

Four new quantities have been proposed by the ICRP for use in radiation protection from external sources, i.e. the ambient dose equivalent, the directional dose equivalent, the individual dose equivalent (penetrating), and the individual dose equivalent (superficial). These quantities are briefly described together with two new concepts of expanded and aligned fields. The BCRU recommends that these quantities should be adopted for use in the UK together with conversion coefficients when re-calibrating existing instruments, reporting the results of measurements and designing instruments. (UK)

The Quality of Quantity: Mini-UAVS As An Alternative UAV Acquisition Strategy at the Army Brigade Level

National Research Council Canada - National Science Library

Weed, Shawn

2002-01-01

This monograph asks should the U.S. Army alter its current UAV acquisition strategy for maneuver brigades from one in which limited numbers of high capability systems are acquired, in favor of another that fields a large quantity...

A conserved quantity in thin body dynamics

International Nuclear Information System (INIS)

Hanna, J.A.; Pendar, H.

2016-01-01

Thin, solid bodies with metric symmetries admit a restricted form of reparameterization invariance. Their dynamical equilibria include motions with both rigid and flowing aspects. On such configurations, a quantity is conserved along the intrinsic coordinate corresponding to the symmetry. As an example of its utility, this conserved quantity is combined with linear and angular momentum currents to construct solutions for the equilibria of a rotating, flowing string, for which it is akin to Bernoulli's constant. - Highlights: • A conserved quantity relevant to the dynamical equilibria of thin structures. • A mixed Lagrangian–Eulerian non-material action principle for fixed windows of axially moving systems. • Analytical solutions for rotating, flowing strings (yarn balloons). • Noether meets Bernoulli in a textile factory.

A conserved quantity in thin body dynamics

Energy Technology Data Exchange (ETDEWEB)

Hanna, J.A., E-mail: hannaj@vt.edu [Department of Biomedical Engineering and Mechanics, Virginia Polytechnic Institute and State University, Blacksburg, VA 24061 (United States); Department of Physics, Virginia Polytechnic Institute and State University, Blacksburg, VA 24061 (United States); Pendar, H. [Department of Biomedical Engineering and Mechanics, Virginia Polytechnic Institute and State University, Blacksburg, VA 24061 (United States)

2016-02-15

Thin, solid bodies with metric symmetries admit a restricted form of reparameterization invariance. Their dynamical equilibria include motions with both rigid and flowing aspects. On such configurations, a quantity is conserved along the intrinsic coordinate corresponding to the symmetry. As an example of its utility, this conserved quantity is combined with linear and angular momentum currents to construct solutions for the equilibria of a rotating, flowing string, for which it is akin to Bernoulli's constant. - Highlights: • A conserved quantity relevant to the dynamical equilibria of thin structures. • A mixed Lagrangian–Eulerian non-material action principle for fixed windows of axially moving systems. • Analytical solutions for rotating, flowing strings (yarn balloons). • Noether meets Bernoulli in a textile factory.

The ICRU dose equivalence quantities in radiation protection

International Nuclear Information System (INIS)

Grimbergen, T.W.M.

1990-09-01

The definitions and application of the new ICRU radiation protection quantities have been reviewed and studied in literature. Special emphasis was laid on the consequences of the use of the new quantities by personnel dosimetry services, and on the consequences of the use of the new quantities during an intercomparison programme for dosimetry services. The study shows that the recommendations of the ICRU are not yet complete and not fully realizable. This means that the dosimetry services always have to make certain approximations, when they use the new quantities. In literature, several approaches have been proposed. The feasibility of an approach depends on the characteristics of the dosimeters used. The use of different approaches by the dosimetry services is thought to be of possible influence on the results of an intercomparison programme. (author). 42 refs.; 3 figs.; 1 tab

The algebras of large N matrix mechanics

Energy Technology Data Exchange (ETDEWEB)

Halpern, M.B.; Schwartz, C.

1999-09-16

Extending early work, we formulate the large N matrix mechanics of general bosonic, fermionic and supersymmetric matrix models, including Matrix theory: The Hamiltonian framework of large N matrix mechanics provides a natural setting in which to study the algebras of the large N limit, including (reduced) Lie algebras, (reduced) supersymmetry algebras and free algebras. We find in particular a broad array of new free algebras which we call symmetric Cuntz algebras, interacting symmetric Cuntz algebras, symmetric Bose/Fermi/Cuntz algebras and symmetric Cuntz superalgebras, and we discuss the role of these algebras in solving the large N theory. Most important, the interacting Cuntz algebras are associated to a set of new (hidden!) local quantities which are generically conserved only at large N. A number of other new large N phenomena are also observed, including the intrinsic nonlocality of the (reduced) trace class operators of the theory and a closely related large N field identification phenomenon which is associated to another set (this time nonlocal) of new conserved quantities at large N.

The method of arbitrarily large moments to calculate single scale processes in quantum field theory

Energy Technology Data Exchange (ETDEWEB)

Bluemlein, Johannes [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Schneider, Carsten [Johannes Kepler Univ., Linz (Austria). Research Inst. for Symbolic Computation (RISC)

2017-01-15

We device a new method to calculate a large number of Mellin moments of single scale quantities using the systems of differential and/or difference equations obtained by integration-by-parts identities between the corresponding Feynman integrals of loop corrections to physical quantities. These scalar quantities have a much simpler mathematical structure than the complete quantity. A sufficiently large set of moments may even allow the analytic reconstruction of the whole quantity considered, holding in case of first order factorizing systems. In any case, one may derive highly precise numerical representations in general using this method, which is otherwise completely analytic.

Foreign materials in the repository - update of estimated quantities

International Nuclear Information System (INIS)

Hagros, A.

2007-03-01

In a repository for spent nuclear fuel, a variety of materials are used during the construction process and during the operation of the repository. In addition to materials necessary for the construction and operation, some materials may be transported into the repository through the ventilation air, as emissions from vehicles, as waste produced by the staff etc. Both of these two types of materials are considered here and their quantities - both the introduced quantities and the quantities that remain after closure - in the repository constructed at Olkiluoto in Eurajoki, Finland are estimated here based on new information. This work is intended to update the estimations that have been made previously, and it takes advantage of the experience collected during the construction of the underground rock characterisation facility ONKALO at Olkiluoto. During this construction process, the quantities of the different construction materials introduced into the underground openings have been monitored and they form a basis for estimating the quantities to be used in the future. The estimations made in this report are specific to a KBS-3V type repository and to the Olkiluoto site, although in some cases more generic information has been used, particularly when the relevant quantities have not been monitored in the ONKALO. The estimations are based on the new repository layout produced in 2006 and consider the latest plans for grouting and rock support. As these plans are generally not final yet, several different alternative plans are assumed when necessary. Also two different strategies for the backfilling of the tunnels are considered. The most significant differences with respect to the results of an earlier estimation are related to the materials used in grouting, shotcreting and in support bolts. In the cases where a mixture of bentonite and crushed rock is the used backfill alternative, gypsum and cement are the materials with the largest quantities remaining in the

Quantities of natural gas transmitted in January-December 2012. Quantities of natural gas transported in January-December 2012

International Nuclear Information System (INIS)

2013-01-01

GRTgaz is a European leader in natural gas transmission, a world expert in gas transmission networks and systems, and an operator firmly committed to the energy transition. It owns and operates the gas transmission network throughout most of France and it manages the transmission network in Germany, thereby helping to ensure correct operation of the French and European gas market. It contributes to the energy security of regional supply systems and performs a public service mission to ensure the continuity of consumer supply. This document presents the monthly key figures of GRTgaz activity in 2012: Total quantities transmitted by GRTgaz (Inputs to the GRTgaz network/Outputs from the GRTgaz network); Maximum and minimum daily flow (Daily quantities transported, Daily consumption, Daily inputs excluding storage); Quantities exchanged on the wholesale market; Consumption on the GRTgaz Network (gross monthly consumption and Average monthly temperatures)

Trade-offs in size, quantity and reliability of generalized nuclear power plants

International Nuclear Information System (INIS)

Hill, D.; Mubayi, V.

1987-01-01

In the 1960's and 1970's, there was rapid growth in the size of newly started nuclear power plants because of the anticipated advantages of increasing scale. Any such advantages were overwhelmed by the complications that arose with long construction times, and attention is now being given to a ''second generation'' of smaller plants of new design. Providing the same production capacity will require larger numbers of plants if they are smaller. Although it seems to have received little attention previously, there should be compensating economies due to ''learning curve'' effects in the manufacture of multiple units of standardized designs (Hill 1983). Moreover, the use of a large number of smaller units increases the overall system reliability. On balance, however, it is not clear how scale, quantity, and reliability considerations interact to determine optimal plant size. The purpose of this paper is to begin examining the size-quantity tradeoff taking into account scale effects, the manufacturing learning curve, plant availability, and system reliability

The large-area CdTe thin film for CdS/CdTe solar cell prepared by physical vapor deposition in medium pressure

Energy Technology Data Exchange (ETDEWEB)

Luo, Run; Liu, Bo; Yang, Xiaoyan; Bao, Zheng; Li, Bing, E-mail: libing70@126.com; Zhang, Jingquan; Li, Wei; Wu, Lili; Feng, Lianghuan

2016-01-01

Graphical abstract: - Highlights: • The large-area CdTe film has been prepared by PVD under the pressure of 0.9 kPa. • The as-prepared CdTe thin film processes excellent photovoltaic properties. • This technique is suitable for depositing large-area CdTe thin film. • The 14.6% champion efficiency CdS/CdTe cell has been achieved. - Abstract: The Cadmium telluride (CdTe) thin film has been prepared by physical vapor deposition (PVD), the Ar + O{sub 2} pressure is about 0.9 kPa. This method is a newer technique to deposit CdTe thin film in large area, and the size of the film is 30 × 40 cm{sup 2}. This method is much different from the close-spaced sublimation (CSS), as the relevance between the source temperature and the substrate temperature is weak, and the gas phase of CdTe is transferred to the substrate by Ar + O{sub 2} flow. Through this method, the compact and uniform CdTe film (30 × 40 cm{sup 2}) has been achieved, and the performances of the CdTe thin film have been determined by transmission spectrum, SEM and XRD. The film is observed to be compact with a good crystallinity, the CdTe is polycrystalline with a cubic structure and a strongly preferred (1 1 1) orientation. Using the CdTe thin film (3 × 5 cm{sup 2}) which is taken from the deposited large-area film, the 14.6% efficiency CdS/CdTe thin film solar cell has been prepared successfully. The structure of the cell is glass/FTO/CdS/CdTe/graphite slurry/Au, short circuit current density (J{sub sc}) of the cell is 26.9 mA/cm{sup 2}, open circuit voltage (V{sub oc}) is 823 mV, and filling factor (FF) is 66.05%. This technique can be a quite promising method to apply in the industrial production, as it has great prospects in the fabricating of large-area CdTe film.

Quantity discrimination in wolves (Canis lupus

Directory of Open Access Journals (Sweden)

Ewelina eUtrata

2012-11-01

Full Text Available Quantity discrimination has been studied extensively in different non-human animal species. In the current study, we tested eleven hand-raised wolves (Canis lupus in a two-way choice task. We placed a number of food items (one to four sequentially into two opaque cans and asked the wolves to choose the larger amount. Moreover, we conducted two additional control conditions to rule out non-numerical properties of the presentation that the animals might have used to make the correct choice. Our results showed that wolves are able to make quantitative judgments at the group, but also at the individual level even when alternative strategies such as paying attention to the surface area or time and total amount are ruled out. In contrast to previous canine studies on dogs (Canis familiaris and coyotes (Canis latrans, our wolves’ performance did not improve with decreasing ratio, referred to as Weber’s law. However, further studies using larger quantities than we used in the current setup are still needed to determine whether and when wolves’ quantity discrimination conforms to Weber’s law.

Layer-Mean Quantities, Local Conservation Laws, and Vorticity

International Nuclear Information System (INIS)

Camassa, R.; Levermore, C.D.

1997-01-01

We derive local conservation laws for layer-mean quantities in two general settings. When applied to Euler flows, the first of these settings yields well-known local conservation laws for quantities averaged between material surfaces. The second, however, leads to new local conservation laws for quantities involving the vorticity that are averaged between arbitrary surfaces. These produce the crucial vorticity conservation laws in shallow water models that admit nonhydrostatic and noncolumnar motion. Moreover, they seem to lie outside the Hamiltonian paradigm of fluid dynamics. The formalism generalizes to skew-symmetric matrix fields; applications to electromagnetism are suggested. copyright 1997 The American Physical Society

The Radiometric Measurement Quantity for SAR Images

OpenAIRE

Döring, Björn J.; Schwerdt, Marco

2013-01-01

A Synthetic Aperture Radar (SAR) system measures among other quantities the terrain radar reflectivity. After image calibration, the pixel intensities are commonly expressed in terms of radar cross sections (for point targets) or as backscatter coefficients (for distributed targets), which are directly related. This paper argues that pixel intensities are not generally proportional to radar cross section or derived physical quantities. The paper further proposes to replace the inaccurate term...

The method of arbitrarily large moments to calculate single scale processes in quantum field theory

Directory of Open Access Journals (Sweden)

Johannes Blümlein

2017-08-01

Full Text Available We devise a new method to calculate a large number of Mellin moments of single scale quantities using the systems of differential and/or difference equations obtained by integration-by-parts identities between the corresponding Feynman integrals of loop corrections to physical quantities. These scalar quantities have a much simpler mathematical structure than the complete quantity. A sufficiently large set of moments may even allow the analytic reconstruction of the whole quantity considered, holding in case of first order factorizing systems. In any case, one may derive highly precise numerical representations in general using this method, which is otherwise completely analytic.

Forage quantity and quality

Science.gov (United States)

Jorgenson, Janet C.; Udevitz, Mark S.; Felix, Nancy A.; Douglas, David C.; Reynolds, Patricia E.; Rhode, E.B.

2002-01-01

The Porcupine caribou herd has traditionally used the coastal plain of the Arctic National Wildlife Refuge, Alaska, for calving. Availability of nutritious forage has been hypothesized as one of the reasons the Porcupine caribou herd migrates hundreds of kilometers to reach the coastal plain for calving (Kuropat and Bryant 1980, Russell et al. 1993).Forage quantity and quality and the chronology of snowmelt (which determines availability and phenological stages of forage) have been suggested as important habitat attributes that lead calving caribou to select one area over another (Lent 1980, White and Trudell 1980, Eastland et al. 1989). A major question when considering the impact of petroleum development is whether potential displacement of the caribou from the 1002 Area to alternate calving habitat will limit access to high quantity and quality forage.Our study had the following objectives: 1) quantify snowmelt patterns by area; 2) quantify relationships among phenology, biomass, and nutrient content of principal forage species by vegetation type; and 3) determine if traditional concentrated calving areas differ from adjacent areas with lower calving densities in terms of vegetation characteristics.

Among-species differences in pollen quality and quantity limitation: implications for endemics in biodiverse hotspots.

Science.gov (United States)

Alonso, Conchita; Navarro-Fernández, Carmen M; Arceo-Gómez, Gerardo; Meindl, George A; Parra-Tabla, Víctor; Ashman, Tia-Lynn

2013-11-01

Insufficient pollination is a function of quantity and quality of pollen receipt, and the relative contribution of each to pollen limitation may vary with intrinsic plant traits and extrinsic ecological properties. Community-level studies are essential to evaluate variation across species in quality limitation under common ecological conditions. This study examined whether endemic species are more limited by pollen quantity or quality than non-endemic co-flowering species in three endemic-rich plant communities located in biodiversity hotspots of different continents (Andalusia, California and Yucatan). Natural variations in pollen receipt and pollen tube formation were analysed for 20 insect-pollinated plants. Endemic and non-endemic species that co-flowered were paired in order to estimate and compare the quantity and quality components of pre-zygotic pollination success, obtained through piecewise regression analysis of the relationship between pollen grains and pollen tubes of naturally pollinated wilted flowers. Pollen tubes did not frequently exceed the number of ovules per flower. Only the combination of abundant and good quality pollen and a low number of ovules per flower conferred relief from pre-zygotic pollen limitation in the three stochastic pollination environments studied. Quality of pollen receipt was found to be as variable as quantity among study species. The relative pollination success of endemic and non-endemic species, and its quantity and quality components, was community dependent. Assessing both quality and quantity of pollen receipt is key to determining the ovule fertilization potential of both endemic and widespread plants in biodiverse hotspot regions. Large natural variation among flowers of the same species in the two components and pollen tube formation deserves further analysis in order to estimate the environmental, phenotypic and intraindividual sources of variation that may affect how plants evolve to overcome this limitation in

Large number discrimination by mosquitofish.

Directory of Open Access Journals (Sweden)

Christian Agrillo

Full Text Available BACKGROUND: Recent studies have demonstrated that fish display rudimentary numerical abilities similar to those observed in mammals and birds. The mechanisms underlying the discrimination of small quantities (<4 were recently investigated while, to date, no study has examined the discrimination of large numerosities in fish. METHODOLOGY/PRINCIPAL FINDINGS: Subjects were trained to discriminate between two sets of small geometric figures using social reinforcement. In the first experiment mosquitofish were required to discriminate 4 from 8 objects with or without experimental control of the continuous variables that co-vary with number (area, space, density, total luminance. Results showed that fish can use the sole numerical information to compare quantities but that they preferentially use cumulative surface area as a proxy of the number when this information is available. A second experiment investigated the influence of the total number of elements to discriminate large quantities. Fish proved to be able to discriminate up to 100 vs. 200 objects, without showing any significant decrease in accuracy compared with the 4 vs. 8 discrimination. The third experiment investigated the influence of the ratio between the numerosities. Performance was found to decrease when decreasing the numerical distance. Fish were able to discriminate numbers when ratios were 1:2 or 2:3 but not when the ratio was 3:4. The performance of a sample of undergraduate students, tested non-verbally using the same sets of stimuli, largely overlapped that of fish. CONCLUSIONS/SIGNIFICANCE: Fish are able to use pure numerical information when discriminating between quantities larger than 4 units. As observed in human and non-human primates, the numerical system of fish appears to have virtually no upper limit while the numerical ratio has a clear effect on performance. These similarities further reinforce the view of a common origin of non-verbal numerical systems in all

A conserved quantity in thin body dynamics

Science.gov (United States)

Hanna, J. A.; Pendar, H.

2016-02-01

Thin, solid bodies with metric symmetries admit a restricted form of reparameterization invariance. Their dynamical equilibria include motions with both rigid and flowing aspects. On such configurations, a quantity is conserved along the intrinsic coordinate corresponding to the symmetry. As an example of its utility, this conserved quantity is combined with linear and angular momentum currents to construct solutions for the equilibria of a rotating, flowing string, for which it is akin to Bernoulli's constant.

Theoretical analysis and experimental study on breakaway torque of large-diameter magnetic liquid seal at low temperature

Science.gov (United States)

Zhang, Haina; Li, Decai; Wang, Qinglei; Zhang, Zhili

2013-07-01

The existing researches of the magnetic liquid rotation seal have been mainly oriented to the seal at normal temperature and the seal with the smaller shaft diameter less than 100 mm. However, the large-diameter magnetic liquid rotation seal at low temperature has not been reported both in theory and in application up to now. A key factor restricting the application of the large-diameter magnetic liquid rotation seal at low temperature is the high breakaway torque. In this paper, the factors that influence the breakaway torque including the number of seal stages, the injected quantity of magnetic liquid and the standing time at normal temperature are studied. Two kinds of magnetic liquid with variable content of large particles are prepared first, and a seal feedthrough with 140 mm shaft diameter is used in the experiments. All experiments are carried out in a low temperature chamber with a temperature range from 200°C to -100°C. Different numbers of seal stages are tested under the same condition to study the relation between the breakaway torque and the number of seal stages. Variable quantity of magnetic liquid is injected in the seal gap to get the relation curve of the breakaway torque and the injecting quantity of magnetic liquid. In the experiment for studying the relation between the breakaway torque and the standing time at the normal temperature, the seal feedtrough is laid at normal temperature for different period of time before it is put in the low temperature chamber. The experimental results show that the breakaway torque is proportional to the number of seal stages, the injected quantity of magnetic liquid and the standing time at the normal temperature. Meanwhile, the experimental results are analyzed and the torque formula of magnetic liquid rotation seal at low temperature is deduced from the Navier-Stokes equation on the base of the model of magnetic liquid rotation seal. The presented research can make wider application of the magnetic liquid

[Evaluation of preparation of curved root canals using hand-used ProTaper].

Science.gov (United States)

Nie, Min; Zhao, Xin-Chen; Peng, Bin; Fan, Ming-Wen; Bian, Zhuan

2009-05-01

To evaluate the shaping ability of hand-used ProTaper on curved canals using Endodontic Cube. Fifty-four curved root canals in vitro were selected and divided into three groups according to the curved degree (alpha), group A: 0 degrees hand-used ProTaper. Before and after shaping, photograph of all the sections were taken under a stereomicroscope. Statistical analyses were performed. The dentin cutting quantity of the whole canal prepared with ProTaper in group B and C was larger than that of group A. The deviation distance of the whole canal prepared by ProTaper in group C was significantly larger than that in group A, and the deviation distance in middle portion larger than that in group B. The maintaining ability in the middle portion of group C by ProTaper was worse than that of group A and B. The curvature of root canal may increase the cutting quantity of the -dentin and reduce the ability of remaining original canal shape prepared by ProTaper.

Relationships of chemical composition, quantity of milt to fertility and ...

African Journals Online (AJOL)

African Journal of Food, Agriculture, Nutrition and Development ... determining the right quantity of milt that can be used to fertilize certain quantity of eggs. ... quantity of milt used for artificial reproduction in fish significantly affect water quality used ... is the major organic substance that supplies the spermatozoa with energy.

Six categories of ionizing radiation quantities practical in various fields

International Nuclear Information System (INIS)

Zheng Junzheng; Zhuo Weihai

2011-01-01

This paper is the part of review on the evolvement of the systems for ionizing radiation quantities and units. In the paper, for better understanding and correct use of the relevant quantities of ionizing radiation, the major ionizing radiation quantities in various fields are divided into six categories. (authors)

Lie-Mei symmetry and conserved quantities of the Rosenberg problem

International Nuclear Information System (INIS)

Liu Xiao-Wei; Li Yuan-Cheng

2011-01-01

The Rosenberg problem is a typical but not too complicated problem of nonholonomic mechanical systems. The Lie—Mei symmetry and the conserved quantities of the Rosenberg problem are studied. For the Rosenberg problem, the Lie and the Mei symmetries for the equation are obtained, the conserved quantities are deduced from them and then the definition and the criterion for the Lie—Mei symmetry of the Rosenberg problem are derived. Finally, the Hojman conserved quantity and the Mei conserved quantity are deduced from the Lie—Mei symmetry. (general)

Lie-Mei symmetry and conserved quantities of the Rosenberg problem

Science.gov (United States)

Liu, Xiao-Wei; Li, Yuan-Cheng

2011-07-01

The Rosenberg problem is a typical but not too complicated problem of nonholonomic mechanical systems. The Lie—Mei symmetry and the conserved quantities of the Rosenberg problem are studied. For the Rosenberg problem, the Lie and the Mei symmetries for the equation are obtained, the conserved quantities are deduced from them and then the definition and the criterion for the Lie—Mei symmetry of the Rosenberg problem are derived. Finally, the Hojman conserved quantity and the Mei conserved quantity are deduced from the Lie—Mei symmetry.

Optimal trading quantity integration as a basis for optimal portfolio management

Directory of Open Access Journals (Sweden)

Saša Žiković

2005-06-01

Full Text Available The author in this paper points out the reason behind calculating and using optimal trading quantity in conjunction with Markowitz’s Modern portfolio theory. In the opening part the author presents an example of calculating optimal weights using Markowitz’s Mean-Variance approach, followed by an explanation of basic logic behind optimal trading quantity. The use of optimal trading quantity is not limited to systems with Bernoulli outcome, but can also be used when trading shares, futures, options etc. Optimal trading quantity points out two often-overlooked axioms: (1 a system with negative mathematical expectancy can never be transformed in a system with positive mathematical expectancy, (2 by missing the optimal trading quantity an investor can turn a system with positive expectancy into a negative one. Optimal trading quantity is that quantity which maximizes geometric mean (growth function of a particular system. To determine the optimal trading quantity for simpler systems, with a very limited number of outcomes, a set of Kelly’s formulas is appropriate. In the conclusion the summary of the paper is presented.

Natural products phytotoxicity A bioassay suitable for small quantities of slightly water-soluble compounds.

Science.gov (United States)

Dornbos, D L; Spencer, G F

1990-02-01

A large variety of secondary metabolites that can inhibit germination and/or seedling growth are produced by plants in low quantities. The objective of this study was to develop a bioassay capable of reliably assessing reductions in germination percentage and seedling length of small-seeded plant species caused by exposure to minute quantities of these compounds. The germination and growth of alfalfa (Medicago saliva), annual ryegrass (Lolium multiflorum), and velvetleaf (Abutilon theophrasti) were evaluated against six known phytotoxins from five chemical classes; cinmethylin (a herbicidal cineole derivative) was selected as a comparison standard. Each phytotoxin, dissolved in a suitable organic solvent, was placed on water-agar in small tissue culture wells. After the solvent evaporated, imbibed seeds were placed on the agar; after three days, germination percentages and seedling lengths were measured. Compared to a commonly used filter paper procedure, this modified agar bioassay required smaller quantities of compound per seed for comparable bioassay results. This bioassay also readily permitted the measurement of seedling length, a more sensitive indicator of phytotoxicity than germination. Seedling length decreased sigmoidally as the toxin concentration increased logarithmically. Phytotoxicity was a function of both compound and plant species. Cinmethylin, a grass herbicide, reduced the length of annual ryegrass seedlings by 90-100%, whereas that of alfalfa and velvetleaf was inhibited slightly. The agar bioassay facilitated the rapid and reliable testing of slightly water-soluble compounds, requiring only minute quantities of each compound to give reproducible results.

21 CFR 1314.20 - Restrictions on sales quantity.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Restrictions on sales quantity. 1314.20 Section 1314.20 Food and Drugs DRUG ENFORCEMENT ADMINISTRATION, DEPARTMENT OF JUSTICE RETAIL SALE OF SCHEDULED LISTED CHEMICAL PRODUCTS Sales by Regulated Sellers § 1314.20 Restrictions on sales quantity. (a) Without...

Sample preparation

International Nuclear Information System (INIS)

Anon.

1992-01-01

Sample preparation prior to HPLC analysis is certainly one of the most important steps to consider in trace or ultratrace analysis. For many years scientists have tried to simplify the sample preparation process. It is rarely possible to inject a neat liquid sample or a sample where preparation may not be any more complex than dissolution of the sample in a given solvent. The last process alone can remove insoluble materials, which is especially helpful with the samples in complex matrices if other interactions do not affect extraction. Here, it is very likely a large number of components will not dissolve and are, therefore, eliminated by a simple filtration process. In most cases, the process of sample preparation is not as simple as dissolution of the component interest. At times, enrichment is necessary, that is, the component of interest is present in very large volume or mass of material. It needs to be concentrated in some manner so a small volume of the concentrated or enriched sample can be injected into HPLC. 88 refs

Quantity-split strategy under two-contractor competitive procurement environment

OpenAIRE

Boger, Dan C.; Liao, Shu S.

1988-01-01

This report discusses the various market scenarios that provide bid price manipulation opportunities under the dual source competition environment. Two different quantity-split strategies were developed one for the case when one of the suppliers does not have the capacity to produce the majority of the annual quantity requirement and the other for the case when neither contractor is interested in using low prices to capture the larger share of annual quantity. Keywords: Dual sourcing, Quantit...

Preparation by the nano-casting process of novel porous carbons from large pore zeolite templates

International Nuclear Information System (INIS)

F Gaslain; J Parmentier; V Valtchev; J Patarin; C Vix Guterl

2005-01-01

The development of new growing industrial applications such as gas storage (e.g.: methane or hydrogen) or electric double-layer capacitors has focussed the attention of many research groups. For this kind of application, porous carbons with finely tailored micro-porosity (i.e.: pore size diameter ≤ 1 nm) appear as very promising materials due to their high surface area and their specific pore size distribution. In order to meet these requirements, attention has been paid towards the feasibility of preparing microporous carbons by the nano-casting process. Since the sizes and shapes of the pores and walls respectively become the walls and pores of the resultant carbons, using templates with different framework topologies leads to various carbon replicas. The works performed with commercially available zeolites employed as templates [1-4] showed that the most promising candidate is the FAU-type zeolite, which is a large zeolite with three-dimensional channel system. The promising results obtained on FAU-type matrices encouraged us to study the microporous carbon formation on large pore zeolites synthesized in our laboratory, such as EMC-1 (International Zeolite Association framework type FAU), zeolite β (BEA) or EMC-2 (EMT). The carbon replicas were prepared following largely the nano-casting method proposed for zeolite Y by the Kyotani research group [4]: either by liquid impregnation of furfuryl alcohol (FA) followed by carbonization or by vapour deposition (CVD) of propylene, or by an association of these two processes. Heat treatment of the mixed materials (zeolite / carbon) could also follow in order to improve the structural ordering of the carbon. After removal of the inorganic template by an acidic treatment, the carbon materials obtained were characterised by several analytical techniques (XRD, N 2 and CO 2 adsorption, electron microscopy, etc...). The unique characteristics of these carbons are discussed in details in this paper and compared to those

Preparation of Al/Si functionally graded materials using ultrasonic separation method

Directory of Open Access Journals (Sweden)

Zhang Zhongtao

2008-08-01

Full Text Available Functionally graded materials (FGM have been widely used in many industries such as aerospace, energy and electronics. In this experimental study of fabricating FGM, an approach was developed to prepare Al/Si FGM using power ultrasonic separation method. Material sample with continuously changing composition and performance/properties was successfully produced. Results showed that the microstructure of the FGM sample transited, from its top to bottom, from the hypereutectic structure with a large quantity of primary Si gradually to the eutectic, and fi nally to the hypoeutectic with numerous primary Al dendrites. The distribution of primary Si and microhardness of the FGM sample also presented graded characteristics, resulting that the wear resistance of the FGM sample decreased from top to bottom. Preliminary discussion was made on the mechanism of the formation of Al/Si FGM.

Editorial: New operational dose equivalent quantities

International Nuclear Information System (INIS)

Harvey, J.R.

1985-01-01

The ICRU Report 39 entitled ''Determination of Dose Equivalents Resulting from External Radiation Sources'' is briefly discussed. Four new operational dose equivalent quantities have been recommended in ICRU 39. The 'ambient dose equivalent' and the 'directional dose equivalent' are applicable to environmental monitoring and the 'individual dose equivalent, penetrating' and the 'individual dose equivalent, superficial' are applicable to individual monitoring. The quantities should meet the needs of day-to-day operational practice, while being acceptable to those concerned with metrological precision, and at the same time be used to give effective control consistent with current perceptions of the risks associated with exposure to ionizing radiations. (U.K.)

48 CFR 245.7309-8 - Variations in quantity or weight.

Science.gov (United States)

2010-10-01

... Inventory 245.7309-8 Variations in quantity or weight. When property is sold on a “unit price” basis, the Contractor reserves the right to vary by up to 15 percent the quantity or weight listed in the Invitation and... price shall be adjusted in accordance with the unit price and on the basis of the quantity or weight...

Low-Temperature Preparation of Tungsten Oxide Anode Buffer Layer via Ultrasonic Spray Pyrolysis Method for Large-Area Organic Solar Cells.

Science.gov (United States)

Ji, Ran; Zheng, Ding; Zhou, Chang; Cheng, Jiang; Yu, Junsheng; Li, Lu

2017-07-18

Tungsten oxide (WO₃) is prepared by a low-temperature ultrasonic spray pyrolysis method in air atmosphere, and it is used as an anode buffer layer (ABL) for organic solar cells (OSCs). The properties of the WO₃ transition metal oxide material as well as the mechanism of ultrasonic spray pyrolysis processes are investigated. The results show that the ultrasonic spray pyrolysized WO₃ ABL exhibits low roughness, matched energy level, and high conductivity, which results in high charge transport efficiency and suppressive recombination in OSCs. As a result, compared to the OSCs based on vacuum thermal evaporated WO₃, a higher power conversion efficiency of 3.63% is reached with low-temperature ultrasonic spray pyrolysized WO₃ ABL. Furthermore, the mostly spray-coated OSCs with large area was fabricated, which has a power conversion efficiency of ~1%. This work significantly enhances our understanding of the preparation and application of low temperature-processed WO₃, and highlights the potential of large area, all spray coated OSCs for sustainable commercial fabrication.

Large-scale distribution of tritium in a commercial product

International Nuclear Information System (INIS)

Combs, F.; Doda, R.J.

1979-01-01

Tritium enters the environment from various sources including nuclear reactor operations, weapons testing, natural production, and from the manufacture, use and ultimate disposal of commercial products containing tritium. A recent commercial application of tritium in the United States of America involves the backlighting of liquid crystal displays (LCD) in digital electronic watches. These watches are distributed through normal commercial channels to the general public. One million curies (MCi) of tritium were distributed in 1977 in this product. This is a significant quantity of tritium compared with power reactor-produced tritium (3MCi yearly) or with naturally produced tritium (6MCi yearly). This is the single largest commercial application involving tritium to date. The final disposition of tritium from large quantities of this product, after its useful life, must be estimated by considering the means of disposal and the possibility of dispersal of tritium concurrent with disposal. The most likely method of final disposition of this product will be disposal in solid refuse; this includes burial in land fills and incineration. Burial in land fills will probably contain the tritium for its effective lifetime, whereas incineration will release all the tritium gas (as the oxide) to the atmosphere. The use and disposal of this product will be studied as part of an environmental study that is at present being prepared for the U.S. Nuclear Regulatory Commission. (author)

Quantity and structure of word knowledge across adulthood.

Science.gov (United States)

Salthouse, Timothy A

2014-09-01

Cross-sectional and longitudinal data from moderately large samples of healthy adults confirmed prior findings of age-related declines in measures of the quantity of word knowledge beginning around age 65. Additional analyses were carried out to investigate the interrelations of different types of vocabulary knowledge at various periods in adulthood. Although the organizational structures were similar in adults of different ages, scores on tests with different formats had weaker relations to a higher-order vocabulary construct beginning when adults were in their 60's. The within-person dispersion among different vocabulary test scores was also greater after about 65 years of age. The discovery of quantitative decreases in amount of knowledge occurring at about the same age as qualitative shifts in the structure of knowledge raises the possibility that the two types of changes may be causally linked.

Water quantity and quality optimization modeling of dams operation based on SWAT in Wenyu River Catchment, China.

Science.gov (United States)

Zhang, Yongyong; Xia, Jun; Chen, Junfeng; Zhang, Minghua

2011-02-01

Water quantity and quality joint operation is a new mode in the present dams' operation research. It has become a hot topic in governmental efforts toward integrated basin improvement. This paper coupled a water quantity and quality joint operation model (QCmode) and genetic algorithm with Soil and Water Assessment Tool (SWAT). Together, these tools were used to explore a reasonable operation of dams and floodgates at the basin scale. Wenyu River Catchment, a key area in Beijing, was selected as the case study. Results showed that the coupled water quantity and quality model of Wenyu River Catchment more realistically simulates the process of water quantity and quality control by dams and floodgates. This integrated model provides the foundation for research of water quantity and quality optimization on dam operation in Wenyu River Catchment. The results of this modeling also suggest that current water quality of Wenyu River will improve following the implementation of the optimized operation of the main dams and floodgates. By pollution control and water quantity and quality joint operation of dams and floodgates, water quality of Wenyu river will change significantly, and the available water resources will increase by 134%, 32%, 17%, and 82% at the downstream sites of Sha River Reservoir, Lutong Floodgate, Xinpu Floodgate, and Weigou Floodgate, respectively. The water quantity and quality joint operation of dams will play an active role in improving water quality and water use efficiency in Wenyu River Basin. The research will provide the technical support for water pollution control and ecological restoration in Wenyu River Catchment and could be applied to other basins with large number of dams. Its application to the Wenyu River Catchment has a great significance for the sustainable economic development of Beijing City.

21 CFR 1308.23 - Exemption of certain chemical preparations; application.

Science.gov (United States)

2010-04-01

... special research purposes and not for general administration to a human being or other animal, if the... concentration that the packaged quantity does not present any significant potential for abuse (the type of packaging and the history of abuse of the same or similar preparations may be considered in determining the...

Preparation and Characterization of a Master Blend of Plutonium Oxide for the 3013 Large Scale Shelf-Life Surveillance Project

Energy Technology Data Exchange (ETDEWEB)

Gillispie, Obie William [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Worl, Laura Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Veirs, Douglas Kirk [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stroud, Mary Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Narlesky, Joshua Edward [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Berg, John M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Kelly, Elizabeth J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Padilla, Dennis D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Bender, Beverly [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Lopez, Annabelle S. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Martinex, Max A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Trujillo, Leonardo A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Wilson, Edward L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-04-10

A mixture of chlorine-containing, impure plutonium oxides has been produced and has been given the name Master Blend. This large quantity of well-characterized chlorinecontaining material is available for use in the Integrated Surveillance and Monitoring Program for shelf-life experiments. It is intended to be representative of materials packaged to meet DOE-STD-3013.1 The Master Blend contains a mixture of items produced in Los Alamos National Laboratory’s (LANL) electro-refining pyrochemical process in the late 1990s. Twenty items were crushed and sieved, calcined to 800ºC for four hours, and blended multiple times. This process resulted in four batches of Master Blend. Calorimetry and density data on material from the four batches indicate homogeneity.

Discussion on concepts for radiological dosimetric quantities in the Japan Health Physics Society

International Nuclear Information System (INIS)

Takahashi, Fumiaki; Oda, Keiji

2007-01-01

Many dosimetric quantities have been used for radiation protection purpose. The International Commission on Radiological Protection (ICRP) has recommended protection quantities and the International Commission on Radiation Units and Measurements (ICRU) has introduced operational quantities to provide a reasonable estimate of the protection quantities. Enthusiastic discussions are continuously made on the issues of the dosimetric quantities, such as basic biological data for the definition of these quantities and applicability of the quantities to actual radiation protection practice. At the moment, some changes are being proposed concerning dosimetric quantities in the draft recommendations of ICRP, opened for consultation in recent years. Thus, the Japan Health Physics Society (JHPS) established the Expert Committee on concepts of Dosimetric Quantities used in radiological protection (ECDQ) in April 2005 to reviewed and discuss issues in the dosimetric quantities. (author)

Management of small quantities of radioactive waste

International Nuclear Information System (INIS)

1998-09-01

The main objective of this publication is to provide practical guidance primarily to developing Member States on the predisposal management of small quantities of radioactive waste arising from hospitals, laboratories, industries, institutions, research reactors and research centres.The publication covers the management of liquid, solid and gaseous radioactive wastes at the users' premises and gives general guidance on procedures at a centralized waste management facility. Predisposal management of radioactive waste includes handling, treatment, conditioning, storage and transportation. This publication provides information and guidance on the following topics: national waste management framework; origin and characteristics of radioactive waste arising from users generating small quantities of waste; radioactive waste management concepts appropriate for small quantities; local waste management; the documentation and approval necessary for the consignment of waste to a centralized waste management facility; centralized waste management; exemption of radionuclides from the regulatory body; transportation; environmental monitoring; quality assurance for the whole predisposal process; regional co-operation aspects

Determining the directions of increasing the innovative potential of the region by developing innovative technologies and competences when preparing and implementing large investment projects

Directory of Open Access Journals (Sweden)

Timur V. Kramin

2015-12-01

Full Text Available Objective to determine the directions of increasing the innovative potential of a region through the development of innovative technologies and competences in the process of preparation and implementation of large investment projects in the Republic of Tatarstan. Methods methodology of project management institutional approach. Results it is proved that the main largescale directions of innovative potential development in the Republic of Tatarstan as a result of preparation and implementing of Universiade 2013 in Kazan are knowledge management information technologies risk management. It is shown that in the framework of the considered innovative areas a complete system was formed of competences of employees and managers in the fields of education trade hospitality and service. Scientific novelty the key directions were defined of increasing the innovative potential of a region through the development of innovative technologies and competences in the process of preparation and implementation of large investment projects by the example of the World Summer Student Games in Kazan in 2013. Practical significance on the basis of specific examples the authors illustrate the practiceoriented mechanism of innovative potential development of a region as a result of implementation of large investment projects. nbsp

Activated carbon prepared from coffee pulp: potential adsorbent of organic contaminants in aqueous solution.

Science.gov (United States)

Gonçalves, Maraisa; Guerreiro, Mário César; Ramos, Paulize Honorato; de Oliveira, Luiz Carlos Alves; Sapag, Karim

2013-01-01

The processing of coffee beans generates large amounts of solid and liquid residues. The solid residues (pulp, husk and parchment) represent a serious environmental problem and do not have an adequate disposal mechanism. In this work, activated carbons (ACs) for adsorption of organic compounds were prepared from coffee pulp by controlled temperature at different pulp/Na2HPO4 ratios (4:1, 2:1, 5:4 and 1:1). The N2 adsorption/desorption isotherms showed ACs with high quantities of mesopores and micropores and specific surface areas of 140, 150, 450 and 440 m(2)g(-1) for AC 4:1, AC 2:1, AC 5:4 and AC 1:1, respectively. The prepared material AC 5:4 showed a higher removal capacity of the organic contaminants methylene blue (MB), direct red (DR) and phenol than did a Merck AC. The maximum capacities for this AC are approximately 150, 120 and 120 mg g(-1) for MB, DR and phenol, respectively. Thus, a good adsorbent was obtained from coffee pulp, an abundant Brazilian residue.

Dosimetric radiation protection quantities. Impact of the forthcoming ICRP recommendations

International Nuclear Information System (INIS)

Pradhan, A.S.; Lee, J.I.; Kim, J.L.; Kim, B.H.

2008-01-01

The physical quantities namely fluence, kerma and absorbed dose provide the base for the operational and the protection quantities. The absorbed dose continues to be the fundamental physical quantity for the radiological protection. The most striking feature relating the quantities in the forthcoming recommendations is the updating of the radiation and tissue weighting factors based on the latest available scientific information on radiobiology and the physics of radiation exposure. This is bound to make a significant impact in arriving at the equivalent doses and effective dose. For external exposures of neutrons, the forthcoming recommendations are going to improve the relationship between the operational and protection quantities. The changes in the tissue weighting factors of some tissues/organs, the inclusion of several new tissues/organs for the consideration of tissue weighting factors and the use of the proposed Reference Male and Reference Female voxel phantoms would require new conversion coefficients and dose coefficients for external and internal exposures. The other striking feature appears to be the details of the concepts to ensure that the protections quantities are used for the appropriate and intended purposes only and the misuse is avoided. (author)

Large coercivity in nanocrystalline TbMn6Sn6 permanent magnets prepared by mechanical milling

International Nuclear Information System (INIS)

Zhang Hongwei; Zhao Tongyun; Zhang Jian; Rong Chuanbing; Zhang Shaoying; Shen Baogen; Li Lu; Zhang Ligang

2003-01-01

Isotropic TbMn 6 Sn 6 was prepared by mechanical milling and subsequent annealing. Although the crystalline grain size was a little larger than 15 nm, no remanence enhancement resulting from intergrain exchange coupling was observed. The coercivity μ 0 H c = 0.96 T at 293 K was much larger than that expected from magnetocrystalline anisotropy. The smallest effective anisotropy constant is suggested to be 0.25 MJ m -3 when the coercivity mechanism is controlled by coherent rotation of magnetization in a single-domain grain. The contributions of shape anisotropy and magnetoelastic anisotropy are considered in order to explain the large coercivity in the magnets

Porous electrode preparation method

Science.gov (United States)

Arons, R.M.; Dusek, J.T.

1983-10-18

A porous sintered plaque is provided with a bimodal porosity that is especially well suited for use as an electrode within a molten carbonate fuel cell. The coarse porosity is sufficient for admitting gases into contact with the reaction surfaces while the fine porosity is wetted with and retains molten electrolyte on the reaction sites. The electrode structure is prepared by providing a very fine powder of such as nickel oxide and blending the powder with a suitable decomposable binder to form a solid mass. The mass is comminuted into agglomerate size particles substantially larger than the fine oxide particles and formed into a cohesive compact for subsequent sintering. Sintering is carried out at sufficient conditions to bind the agglomerates together into a porous structure having both coarse and fine porosity. Where lithiated nickel oxide cathodes are prepared, the sintering conditions can be moderate enough to retain substantial quantities of lithium within the electrode for adequate conductivity. 2 figs.

Application of an experimental irradiation facility type K-120 for the radiation treatment of agricultural products in large quantity

International Nuclear Information System (INIS)

Stenger, V.; Foeldiak, G.; Horvath, I.; Hargittai, P.; Bartfai, Cs.

1979-01-01

During experimental and pilot irradiation carried out by the 60 Co irradiation facility type K-120 of the Institute of Isotopes of the Hungarian Academy of Sciences an irradiation technology for the treatment of agricultural and food products of considerable density has been developed. Applying transport containers of commercial size the intermittent radiation treatment of great quantity products was made possible with homogeneous dose distribution. The radiation technical characteristics, the utilization coefficient and the capacity of the facility for every agricultural product were calculated. (author)

Technical preparation of the Yuzhteploehnergomontazh trust for technological equipment mounting

International Nuclear Information System (INIS)

Zayats, A.I.

1982-01-01

Measures of technical preparation for equipment mounting at the Zaporozhe NPP developed with the Yuzhteploehnergomontazh trust experts are considered. These measures envisage the construction of mounting base of heat facilities, calculation of labour contents and determination of necessary quantity of mounters, development of optimal flowsheet of mounting control, improvement of mounting qualification and creation of stable collective body, improvement of technical level of mounting and welding works, organizational-technical measures on mounting logistics. Factors affecting negatively technical preparation quality of equipment mounting at the Zaporozhe NPP are discussed. The flowsheet of mounting control is presented

Large scale electrolysers

International Nuclear Information System (INIS)

B Bello; M Junker

2006-01-01

Hydrogen production by water electrolysis represents nearly 4 % of the world hydrogen production. Future development of hydrogen vehicles will require large quantities of hydrogen. Installation of large scale hydrogen production plants will be needed. In this context, development of low cost large scale electrolysers that could use 'clean power' seems necessary. ALPHEA HYDROGEN, an European network and center of expertise on hydrogen and fuel cells, has performed for its members a study in 2005 to evaluate the potential of large scale electrolysers to produce hydrogen in the future. The different electrolysis technologies were compared. Then, a state of art of the electrolysis modules currently available was made. A review of the large scale electrolysis plants that have been installed in the world was also realized. The main projects related to large scale electrolysis were also listed. Economy of large scale electrolysers has been discussed. The influence of energy prices on the hydrogen production cost by large scale electrolysis was evaluated. (authors)

Calibration of personal dosimeters: Quantities and terminology

International Nuclear Information System (INIS)

Aleinikov, V.E.

1999-01-01

The numerical results obtained in the interpretation of individual monitoring of external radiation depend not only on the accurate calibration of the radiation measurement instruments involved, but also on the definition of the quantities in term of which these instruments are calibrated The absence of uniformity in terminology not only makes it difficult to understand properly the scientific and technical literature but can also lead to incorrect interpretation of particular concepts and recommendations. In this paper, brief consideration is given to definition of radiation quantities and terminology used in calibration procedures. (author)

On pure-strategy Nash equilibria in price-quantity games

NARCIS (Netherlands)

Bos, I.; Vermeulen, A.J.

2015-01-01

This paper examines the existence and characteristics of pure-strategy Nash equilibria in oligopoly models in which firms set both prices and quantities. Existence is proved for a broad and natural class of price-quantity games. With differentiated products, the equilibrium outcome is similar to

Definitions of Quantities and Units.

Science.gov (United States)

Spurgin, C. B.

1983-01-01

Compares various methods of defining derived quantities, arguing for a definitional formula using base or fundamental units in a word equation, or symbol-equations with the symbols explained. Suggests that fundamental units be defined operationally or left regarded as intuitive as in the case of length and time. (JM)

Workplace stress experienced by quantity surveyors

African Journals Online (AJOL)

Paul (P.A.) Bowen, Department of Construction Economics and Management,. University of Cape Town, Private ..... Explore workplace stress levels among quantity surveyors in the developing nation of ...... London: Free. Association Books.

The Dynamics of Pheromone Gland Synthesis and Release: a Paradigm Shift for Understanding Sex Pheromone Quantity in Female Moths.

Science.gov (United States)

Foster, Stephen P; Anderson, Karin G; Casas, Jérôme

2018-05-10

Moths are exemplars of chemical communication, especially with regard to specificity and the minute amounts they use. Yet, little is known about how females manage synthesis and storage of pheromone to maintain release rates attractive to conspecific males and why such small amounts are used. We developed, for the first time, a quantitative model, based on an extensive empirical data set, describing the dynamical relationship among synthesis, storage (titer) and release of pheromone over time in a moth (Heliothis virescens). The model is compartmental, with one major state variable (titer), one time-varying (synthesis), and two constant (catabolism and release) rates. The model was a good fit, suggesting it accounted for the major processes. Overall, we found the relatively small amounts of pheromone stored and released were largely a function of high catabolism rather than a low rate of synthesis. A paradigm shift may be necessary to understand the low amounts released by female moths, away from the small quantities synthesized to the (relatively) large amounts catabolized. Future research on pheromone quantity should focus on structural and physicochemical processes that limit storage and release rate quantities. To our knowledge, this is the first time that pheromone gland function has been modeled for any animal.

Recognizing Prefixes in Scientific Quantities

Science.gov (United States)

Sokolowski, Andrzej

2015-01-01

Although recognizing prefixes in physical quantities is inherent for practitioners, it might not be inherent for students, who do not use prefixes in their everyday life experiences. This deficiency surfaces in AP Physics exams. For example, readers of an AP Physics exam reported "a common mistake of incorrectly converting nanometers to…

Optimized preparation for large surface area activated carbon from date (Phoenix dactylifera L.) stone biomass

International Nuclear Information System (INIS)

Danish, Mohammed; Hashim, Rokiah; Ibrahim, M.N. Mohamad; Sulaiman, Othman

2014-01-01

The preparation of activated carbon from date stone treated with phosphoric acid was optimized using rotatable central composite design of response surface methodology (RSM). The chemical activating agent concentration and temperature of activation plays a crucial role in preparation of large surface area activated carbons. The optimized activated carbon was characterized using thermogravimetric analysis, field emission scanning electron microscopy, energy dispersive X-ray spectroscopy, powder X-ray diffraction, and Fourier transform infrared spectroscopy. The results showed that the larger surface area of activated carbon from date stone can be achieved under optimum activating agent (phosphoric acid) concentration, 50.0% (8.674 mol L −1 ) and activation temperature, 900 °C. The Brunauer–Emmett–Teller (BET) surface area of optimized activated carbon was found to be 1225 m 2  g −1 , and thermogravimetric analysis revealed that 55.2% mass of optimized activated carbon was found thermally stable till 900 °C. The leading chemical functional groups found in the date stone activated carbon were aliphatic carboxylic acid salt ν(C=O) 1561.22 cm −1 and 1384.52 cm −1 , aliphatic hydrocarbons ν(C–H) 2922.99 cm −1 (C–H sym./asym. stretch frequency), aliphatic phosphates ν(P–O–C) 1054.09 cm −1 , and secondary aliphatic alcohols ν(O–H) 3419.81 cm −1 and 1159.83 cm −1 . - Highlights: • RSM optimization was done for the production of large surface area activated carbon. • Two independent variables with two responses were selected for optimization. • Characterization was done for surface area, morphology and chemical constituents. • Optimized date stone activated carbon achieved surface area 1225 m 2  g −1

30 CFR 75.322 - Harmful quantities of noxious gases.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Harmful quantities of noxious gases. 75.322... quantities of noxious gases. Concentrations of noxious or poisonous gases, other than carbon dioxide, shall... Governmental Industrial Hygienists in “Threshold Limit Values for Substance in Workroom Air” (1972). Detectors...

48 CFR 52.217-6 - Option for Increased Quantity.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Option for Increased....217-6 Option for Increased Quantity. As prescribed in 17.208(d), insert a clause substantially the same as the following: Option for Increased Quantity (MAR 1989) The Government may increase the...

41 CFR 109-27.102 - Economic order quantity principle.

Science.gov (United States)

2010-07-01

... PROCUREMENT 27-INVENTORY MANAGEMENT 27.1-Stock Replenishment § 109-27.102 Economic order quantity principle. ... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Economic order quantity principle. 109-27.102 Section 109-27.102 Public Contracts and Property Management Federal Property...

Low-Temperature Preparation of Tungsten Oxide Anode Buffer Layer via Ultrasonic Spray Pyrolysis Method for Large-Area Organic Solar Cells

Directory of Open Access Journals (Sweden)

Ran Ji

2017-07-01

Full Text Available Tungsten oxide (WO3 is prepared by a low-temperature ultrasonic spray pyrolysis method in air atmosphere, and it is used as an anode buffer layer (ABL for organic solar cells (OSCs. The properties of the WO3 transition metal oxide material as well as the mechanism of ultrasonic spray pyrolysis processes are investigated. The results show that the ultrasonic spray pyrolysized WO3 ABL exhibits low roughness, matched energy level, and high conductivity, which results in high charge transport efficiency and suppressive recombination in OSCs. As a result, compared to the OSCs based on vacuum thermal evaporated WO3, a higher power conversion efficiency of 3.63% is reached with low-temperature ultrasonic spray pyrolysized WO3 ABL. Furthermore, the mostly spray-coated OSCs with large area was fabricated, which has a power conversion efficiency of ~1%. This work significantly enhances our understanding of the preparation and application of low temperature-processed WO3, and highlights the potential of large area, all spray coated OSCs for sustainable commercial fabrication.

Category 3 threshold quantities for hazard categorization of nonreactor facilities

International Nuclear Information System (INIS)

Mandigo, R.L.

1996-01-01

This document provides the information necessary to determine Hazard Category 3 threshold quantities for those isotopes of interest not listed in WHC-CM-4-46, Section 4, Table 1.''Threshold Quantities.''

19 CFR 144.33 - Minimum quantities to be withdrawn.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 2 2010-04-01 2010-04-01 false Minimum quantities to be withdrawn. 144.33 Section 144.33 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT... Warehouse § 144.33 Minimum quantities to be withdrawn. Unless by special authority of the Commissioner of...

Quantity Estimation Of The Interactions

International Nuclear Information System (INIS)

Gorana, Agim; Malkaj, Partizan; Muda, Valbona

2007-01-01

In this paper we present some considerations about quantity estimations, regarding the range of interaction and the conservations laws in various types of interactions. Our estimations are done under classical and quantum point of view and have to do with the interaction's carriers, the radius, the influence range and the intensity of interactions

Controlling air toxics through advanced coal preparation

Energy Technology Data Exchange (ETDEWEB)

Straszheim, W.E.; Buttermore, W.H.; Pollard, J.L. [Iowa State Univ., Ames, IA (United States)

1995-11-01

This project involves the assessment of advanced coal preparation methods for removing trace elements from coal to reduce the potential for air toxic emissions upon combustion. Scanning electron microscopy-based automated image analysis (SEM-AIA) and advanced washability analyses are being applied with state-of-the-art analytical procedures to predict the removal of elements of concern by advanced column flotation and to confirm the effectiveness of preparation on the quality of quantity of clean coal produced. Specific objectives are to maintain an acceptable recovery of combustible product, while improving the rejection of mineral-associated trace elements. Current work has focused on determining conditions for controlling column flotation system across its operating range and on selection and analysis of samples for determining trace element cleanability.

Information quantity in a pixel of digital image

OpenAIRE

Kharinov, M.

2014-01-01

The paper is devoted to the problem of integer-valued estimating of information quantity in a pixel of digital image. The definition of an integer estimation of information quantity based on constructing of the certain binary hierarchy of pixel clusters is proposed. The methods for constructing hierarchies of clusters and generating of hierarchical sequences of image approximations that minimally differ from the image by a standard deviation are developed. Experimental results on integer-valu...

An exploratory investigation of the intuition of physical quantity among 15 to 17 year old high school students from an evolutionary epistemological perspective

Science.gov (United States)

Chernavski, Ghennady

This study examines the issue of perception of extreme amounts of various physical quantities among 14 to 17 year old public schools students. The methods used in this investigation consisted of combined multiple-choice-open response questions and clinical interviews. The subjects in this study have relatively well defined ideas about quantitative relationships of the physical world as long as the quantities involved lie within their perceptual limits. Beyond these limits, their quantitative understanding was vague across all concepts with respect to their inability to do adequate quantitative comparisons. Very small physical quantities as well as very small changes in quantities did not seem to be present in the mental frameworks of the subjects. Most subjects were able to comprehend micro-quantities and micro-changes by relating them to those within their mesocosmical range. Analogical reasoning appeared to be central to this process. The subjects failed to perceive identical physical situations as analogical if one of them involved mesocosmical quantities and the other contained those lying beyond their mental mesocosmical range. Crossing mesocosmical boundaries in one's mind caused interruption in analogical reasoning. Very large physical quantities, namely those beyond the human range of sensual perception, were present in the subjects' mental frameworks. However, they were unable to reason adequately about quantitative differences between distinct quantities of the same concept if these quantities were beyond their sensual range. The findings of this study provide empirical support to Vollmer's (1984) theory of mesocosmical mind.

Processing ordinality and quantity: the case of developmental dyscalculia.

Directory of Open Access Journals (Sweden)

Orly Rubinsten

Full Text Available In contrast to quantity processing, up to date, the nature of ordinality has received little attention from researchers despite the fact that both quantity and ordinality are embodied in numerical information. Here we ask if there are two separate core systems that lie at the foundations of numerical cognition: (1 the traditionally and well accepted numerical magnitude system but also (2 core system for representing ordinal information. We report two novel experiments of ordinal processing that explored the relation between ordinal and numerical information processing in typically developing adults and adults with developmental dyscalculia (DD. Participants made "ordered" or "non-ordered" judgments about 3 groups of dots (non-symbolic numerical stimuli; in Experiment 1 and 3 numbers (symbolic task: Experiment 2. In contrast to previous findings and arguments about quantity deficit in DD participants, when quantity and ordinality are dissociated (as in the current tasks, DD participants exhibited a normal ratio effect in the non-symbolic ordinal task. They did not show, however, the ordinality effect. Ordinality effect in DD appeared only when area and density were randomized, but only in the descending direction. In the symbolic task, the ordinality effect was modulated by ratio and direction in both groups. These findings suggest that there might be two separate cognitive representations of ordinal and quantity information and that linguistic knowledge may facilitate estimation of ordinal information.

Processing ordinality and quantity: the case of developmental dyscalculia.

Science.gov (United States)

Rubinsten, Orly; Sury, Dana

2011-01-01

In contrast to quantity processing, up to date, the nature of ordinality has received little attention from researchers despite the fact that both quantity and ordinality are embodied in numerical information. Here we ask if there are two separate core systems that lie at the foundations of numerical cognition: (1) the traditionally and well accepted numerical magnitude system but also (2) core system for representing ordinal information. We report two novel experiments of ordinal processing that explored the relation between ordinal and numerical information processing in typically developing adults and adults with developmental dyscalculia (DD). Participants made "ordered" or "non-ordered" judgments about 3 groups of dots (non-symbolic numerical stimuli; in Experiment 1) and 3 numbers (symbolic task: Experiment 2). In contrast to previous findings and arguments about quantity deficit in DD participants, when quantity and ordinality are dissociated (as in the current tasks), DD participants exhibited a normal ratio effect in the non-symbolic ordinal task. They did not show, however, the ordinality effect. Ordinality effect in DD appeared only when area and density were randomized, but only in the descending direction. In the symbolic task, the ordinality effect was modulated by ratio and direction in both groups. These findings suggest that there might be two separate cognitive representations of ordinal and quantity information and that linguistic knowledge may facilitate estimation of ordinal information.

Foreign materials in the repository. Update of estimated quantities

International Nuclear Information System (INIS)

Karvonen, T.

2011-06-01

A variety of materials are used during the construction process and the operation of the repository for spent nuclear fuel at Olkiluoto in Eurajoki, Finland. In addition to materials necessary for the construction and operation, some materials may be transported into the repository with the ventilation air, as emissions from vehicles etc. Both of these two types of materials are considered here and both introduced quantities and the quantities that remain after the closure in the repository are estimated here based on the most recent information. This work is intended to update the previous estimations, and it takes advantage of the experience collected during the construction of the underground rock characterisation facility called ONKALO at Olkiluoto. The implemented quantities as well as designs and preliminary designs have been used in calculating the quantities of the foreign materials. The estimations made in this report are specific to a KBS-3V type repository. In some cases more generic information has been used, particularly when the relevant quantities have not been monitored in ONKALO. The estimations are based on the new repository layout produced in 2010 and consider the latest plans for grouting and rock support. As all of these plans are not final some quantities may change in the future. As the repository layout may still go through some changes this report also provides the foreign materials for a hundred meters of different deposition tunnels designed for the OL and LO type canisters1. The results have also been calculated for a space demanded by a deposition tunnel end plug and the tunnel lengths before and after one. The most significant foreign materials are certain accessory minerals of the clay materials followed by organic materials (including the organic carbon from the clay materials), cement, steel and silica. (orig.)

Calibration of personal dosemeters in terms of the ICRU operational quantities

International Nuclear Information System (INIS)

McDonald, J.C.; Hertel, N.E.

1992-01-01

The International Commission on Radiological Units and Measurements (ICRU) has defined several new operational quantities for radiation protection purposes. The quantities to be used for personal monitoring are defined at depths in the human body. Because these quantities are impossible to measure directly, the ICRU has recommended that personal dosimeters should be calibrated under simplified conditions on an appropriate phantom, such as the ICRU sphere. The U.S. personal dosimetry accreditation programs make use of a 30 x 30 x 15 cm polymethylmethacrylate (PMMA) phantom; therefore it is necessary to relate the response of dosimeters calibrated on this phantom to the ICRU operational quantities. Calculations of the conversion factors to compute dosimeter response in terms of the operational quantities have been performed using the code MCNP. These calculations have also been compared to experimental measurements using thermoluminescent (TLD) detectors. (author)

Calibration of personal dosemeters in terms of the ICRU operational quantities

International Nuclear Information System (INIS)

McDonald, J.C.; Hertel, N.E.

1992-05-01

The International Commission on Radiological Units and Measurements (ICRU) has defined several new operational quantities for radiation protection purposes. The quantities to be used for personal monitoring are defined at depths in the human body. Because these quantities are impossible to measure directly, the ICRU has recommended that personal dosemeters should be calibrated under simplified conditions on an appropriate phantom, such as the ICRU sphere. The US personal dosimetry accreditation programs make use of a 30 x 30 x 15 cm polymethymethacrylate (PMMA) phantom, therefore it is necessary to relate the response of dosemeters calibrated on this phantom to the ICRU operational quantities. Calculations of the conversion factors to compute dosemeter response in terms of the operational quantities have been performed using the code MCNP. These calculations have also been compared to experimental measurements using thermoluminescent (TLD) detectors

Variation of organic matter quantity and quality in streams at Critical Zone Observatory watersheds

Science.gov (United States)

Miller, Matthew P.; Boyer, Elizabeth W.; McKnight, Diane M.; Brown, Michael G.; Gabor, Rachel S.; Hunsaker, Carolyn T.; Iavorivska , Lidiia; Inamdar, Shreeram; Kaplan, Louis A.; Johnson, Dale W.; Lin, Henry; McDowell, William H.; Perdrial, Julia N.

2016-01-01

The quantity and chemical composition of dissolved organic matter (DOM) in surface waters influence ecosystem processes and anthropogenic use of freshwater. However, despite the importance of understanding spatial and temporal patterns in DOM, measures of DOM quality are not routinely included as part of large-scale ecosystem monitoring programs and variations in analytical procedures can introduce artifacts. In this study, we used consistent sampling and analytical methods to meet the objective of defining variability in DOM quantity and quality and other measures of water quality in streamflow issuing from small forested watersheds located within five Critical Zone Observatory sites representing contrasting environmental conditions. Results show distinct separations among sites as a function of water quality constituents. Relationships among rates of atmospheric deposition, water quality conditions, and stream DOM quantity and quality are consistent with the notion that areas with relatively high rates of atmospheric nitrogen and sulfur deposition and high concentrations of divalent cations result in selective transport of DOM derived from microbial sources, including in-stream microbial phototrophs. We suggest that the critical zone as a whole strongly influences the origin, composition, and fate of DOM in streams. This study highlights the value of consistent DOM characterization methods included as part of long-term monitoring programs for improving our understanding of interactions among ecosystem processes as controls on DOM biogeochemistry.

Large-scale preparation of clove essential oil and eugenol-loaded liposomes using a membrane contactor and a pilot plant.

Science.gov (United States)

Sebaaly, Carine; Greige-Gerges, Hélène; Agusti, Géraldine; Fessi, Hatem; Charcosset, Catherine

2016-01-01

Based on our previous study where optimal conditions were defined to encapsulate clove essential oil (CEO) into liposomes at laboratory scale, we scaled-up the preparation of CEO and eugenol (Eug)-loaded liposomes using a membrane contactor (600 mL) and a pilot plant (3 L) based on the principle of ethanol injection method, both equipped with a Shirasu Porous Glass membrane for injection of the organic phase into the aqueous phase. Homogenous, stable, nanometric-sized and multilamellar liposomes with high phospholipid, Eug loading rates and encapsulation efficiency of CEO components were obtained. Saturation of phospholipids and drug concentration in the organic phase may control the liposome stability. Liposomes loaded with other hydrophobic volatile compounds could be prepared at large scale using the ethanol injection method and a membrane for injection.

Conserved quantities for generalized KdV equations

International Nuclear Information System (INIS)

Calogero, F.; Rome Univ.; Degasperis, A.; Rome Univ.

1980-01-01

It is noted that the nonlinear evolution equation usub(t) = α(t)usub(xxx) - 6ν(t) usub(x)u, u is identical to u(x,t), possesses three (and, in some cases, four) conserved quantities, that are explicitly displayed. These results are of course relevant only to the cases in which this evolution equation is not known to possess an infinite number of conserved quantities. Purpose and scope of this paper is to report three or four simple conservation laws possessed by the evolution equation usub(t) = α(t)usub(xxx) - 6ν(t)usub(x)u, u is identical to u(x,t). (author)

A geochemical module for "AMDTreat" to compute caustic quantity, effluent quantity, and sludge volume

Science.gov (United States)

Cravotta,, Charles A.; Parkhurst, David L.; Means, Brent P; McKenzie, Bob; Morris, Harry; Arthur, Bill

2010-01-01

Treatment with caustic chemicals typically is used to increase pH and decrease concentrations of dissolved aluminum, iron, and/or manganese in largevolume, metal-laden discharges from active coal mines. Generally, aluminum and iron can be removed effectively at near-neutral pH (6 to 8), whereas active manganese removal requires treatment to alkaline pH (~10). The treatment cost depends on the specific chemical used (NaOH, CaO, Ca(OH)2, Na2CO3, or NH3) and increases with the quantities of chemical added and sludge produced. The pH and metals concentrations do not change linearly with the amount of chemical added. Consequently, the amount of caustic chemical needed to achieve a target pH and the corresponding effluent composition and sludge volume can not be accurately determined without empirical titration data or the application of geochemical models to simulate the titration of the discharge water with caustic chemical(s). The AMDTreat computer program (http://amd.osmre.gov/ ) is widely used to compute costs for treatment of coal-mine drainage. Although AMDTreat can use results of empirical titration with industrial grade caustic chemicals to compute chemical costs for treatment of net-acidic or net-alkaline mine drainage, such data are rarely available. To improve the capability of AMDTreat to estimate (1) the quantity and cost of caustic chemicals to attain a target pH, (2) the concentrations of dissolved metals in treated effluent, and (3) the volume of sludge produced by the treatment, a titration simulation is being developed using the geochemical program PHREEQC (wwwbrr.cr.usgs.gov/projects/GWC_coupled/phreeqc/) that will be coupled as a module to AMDTreat. The simulated titration results can be compared with or used in place of empirical titration data to estimate chemical quantities and costs. This paper describes the development, evaluation, and potential utilization of the PHREEQC titration module for AMDTreat.

Order of 6 October 1977 defining the characteristics of each type of large nuclear installation

International Nuclear Information System (INIS)

1978-01-01

This Order, made by the French Minister of Industry, Commerce and Crafts and the Minister of Labour, lays down the characteristics of large nuclear installations which should be included in the document provided for under Section 10 of decree No. 75-306 of 28 April 1975 on the protection of workers against the hazards of ionizing radiation in large nuclear installations. These include inter alia the reactor type, its nominal power, the nature and cladding of the fuel, the rate of loading/unloading of the fuel, provisions to prevent criticality risks outside normal operation of the reactor, controlled areas and the measures for protection against ionizing radiation. The Order also lays down the characteristics for plants for the preparation and treatment of irradiated nuclear fuels as well as the characteristics of facilities for the storage, use, manufacture and transformation of radioactive substances, and the maximum permissible annual quantities of radioactive releases. (NEA) [fr

Establishment and Evaluation of Decommissioning Plant Inventory DB and Waste Quantity

International Nuclear Information System (INIS)

Oh, Jae Yong; Moon, Sang-Rae; Yun, Taesik; Kim, Hee-Geun; Sung, Nak-Hoon; Jung, Seung Hyuk

2016-01-01

Korea Hydro and Nuclear Power (KHNP) made a decision for permanent shutdown of Kori-1 and has progressed the strategy determination and R and D for the decommissioning of Kori-1. Decommissioning waste, Structure, System and Components (SSCs) is one of the most important elements. Decommissioning waste quantity is calculated based on Plant Inventory Database (PI DB) with activation and contamination data. Due to the largest portion of waste management and disposal in decommissioning, it is necessary to exactly evaluate waste quantity (applying the regulation, guideline and site-specific characterization) for economic feasibility. In this paper, construction of PI DB and evaluation of waste quantity for Optimized Pressurized Reactor (OPR-1000) are mainly described. Decommissioning waste quantities evaluated are going to be applied to calculation of the project cost. In fact, Ministry of Trade, Industry and Energy (MOTIE) in Korea expected the decommissioning waste quantity in a range of 14,500-18,850 drums, and predicted appropriate liability for decommissioning fund by using waste quantity. The result of this study is also computed by the range of 14,500-18,850 drums. Since there is no site-specific data for the NPP site, this evaluation is the preliminary analysis

Establishment and Evaluation of Decommissioning Plant Inventory DB and Waste Quantity

Energy Technology Data Exchange (ETDEWEB)

Oh, Jae Yong; Moon, Sang-Rae; Yun, Taesik; Kim, Hee-Geun [KHNP CRI, Daejeon (Korea, Republic of); Sung, Nak-Hoon; Jung, Seung Hyuk [KONES Corp., Seoul (Korea, Republic of)

2016-10-15

Korea Hydro and Nuclear Power (KHNP) made a decision for permanent shutdown of Kori-1 and has progressed the strategy determination and R and D for the decommissioning of Kori-1. Decommissioning waste, Structure, System and Components (SSCs) is one of the most important elements. Decommissioning waste quantity is calculated based on Plant Inventory Database (PI DB) with activation and contamination data. Due to the largest portion of waste management and disposal in decommissioning, it is necessary to exactly evaluate waste quantity (applying the regulation, guideline and site-specific characterization) for economic feasibility. In this paper, construction of PI DB and evaluation of waste quantity for Optimized Pressurized Reactor (OPR-1000) are mainly described. Decommissioning waste quantities evaluated are going to be applied to calculation of the project cost. In fact, Ministry of Trade, Industry and Energy (MOTIE) in Korea expected the decommissioning waste quantity in a range of 14,500-18,850 drums, and predicted appropriate liability for decommissioning fund by using waste quantity. The result of this study is also computed by the range of 14,500-18,850 drums. Since there is no site-specific data for the NPP site, this evaluation is the preliminary analysis.

Preparation of polymer composites using nanostructured carbon produced at large scale by catalytic decomposition of methane

International Nuclear Information System (INIS)

Suelves, I.; Utrilla, R.; Torres, D.; Llobet, S. de; Pinilla, J.L.; Lázaro, M.J.; Moliner, R.

2013-01-01

Polymer-based composites were prepared using different concentrations of nanostructured carbons (NCs), produced by catalytic decomposition of methane (CDM). Four carbonaceous nanostructures were produced using different catalysts (with Ni and Fe as active phases) in a rotary bed reactor capable of producing up to 20 g of carbon per hour. The effect of nanostructured carbon on the thermal and electrical behaviour of epoxy-based composites is studied. An increase in the thermal stability and the decrease of electrical resistivity were observed for the composites at carbon contents as low as 1 wt%. The highest reduction of the electrical resistivity was obtained using multi-walled carbon nanotubes obtained with the Fe based catalysts. This effect could be related to the high degree of structural order of these materials. The results were compared with those obtained using a commercial carbon nanofibre, showing that the use of carbon nanostructures from CDM can be a valid alternative to the commercial nanofibres. -- Highlights: ► Preparation of polymer nanocomposites with enhanced thermal and electrical properties. ► Formation of nanostructured carbon materials with different textural and structural properties at large scale. ► Catalytic decomposition of methane to simultaneously produce hydrogen and carbon materials.

Preparation of large-area molecular junctions with metallic conducting Langmuir–Blodgett films

Energy Technology Data Exchange (ETDEWEB)

Mochizuki, Kengo [Division of Marine Technology, Tokyo University of Marine Science and Technology, 2-1-6 Etchujima Koto-ku, Tokyo 135-8533 (Japan); Ohnuki, Hitoshi, E-mail: ohnuki@kaiyodai.ac.jp [Division of Marine Technology, Tokyo University of Marine Science and Technology, 2-1-6 Etchujima Koto-ku, Tokyo 135-8533 (Japan); Shimizu, Daisuke [Division of Marine Technology, Tokyo University of Marine Science and Technology, 2-1-6 Etchujima Koto-ku, Tokyo 135-8533 (Japan); Imakubo, Tatsuro [Department of Materials and Technology, Nagaoka University of Technology, 1603-1 Kamitomioka, Nagaoka, Niigata 940-2188 (Japan); Tsuya, Daiju [National Institute for Materials Science,1-2-1 Sengen, Tsukuba, Ibaraki 305-0047 (Japan); Izumi, Mitsuru [Division of Marine Technology, Tokyo University of Marine Science and Technology, 2-1-6 Etchujima Koto-ku, Tokyo 135-8533 (Japan)

2014-03-03

Metallic conducting Langmuir–Blodgett (LB) films were used as soft electrodes to fabricate molecular junctions with self-assembled monolayers (SAMs) of alkanethiols (CH{sub 3}(CH{sub 2}){sub n−1}SH) on an Au surface. Alkanethiols can form highly ordered, stable dielectric SAMs on metal surfaces over large areas. However, it is difficult to establish electrical contacts on such SAMs, which has limited their application. In this work, we used metallic conducting LB films composed of bis(ethylenedioxy)tetrathiafulvalene and stearic acid as a soft electrode onto alkanethiol SAMs (C{sub n}-SAM, n = 12, 14, 16, 18) to prepare Au/SAM/metal junctions of relatively large size (∼ 15.6 × 10{sup 3} μm{sup 2}). The current density–voltage (J–V) characteristics across the junctions exhibited rectifying behavior with a ratio R of ∼ 5 (R = |J(V)|/|J(− V)| at ± 1 V). The lower transfer rate corresponding to the electron transport from Au to the LB films exhibited nonlinear J–V characteristics, while the higher transfer rate of electrons from the LB film to Au showed linear J–V characteristics. Kelvin probe force microscopy revealed that the work function of the metallic LB films was smaller than that of Au. The observed rectification behavior is probably caused by different electron transport mechanisms between the two current directions. - Highlights: • Metallic Langmuir–Blodgett (LB) films were used as soft electrodes. • Molecular junctions of metal–alkanethiol–LB films were fabricated. • The current–voltage curve across the junctions exhibited rectifying behavior. • This is the first observation for alkanethiol monolayer junctions. • The work function difference between the electrodes induces the rectification.

Preparative purification of a high-mannose type N-glycan from soy bean agglutinin by hydrazinolysis and tyrosinamide derivatization.

Science.gov (United States)

Evers, D L; Hung, R L; Thomas, V H; Rice, K G

1998-12-15

The N-linked oligosaccharide from soy bean agglutinin (Man9) was isolated on a preparative scale following derivatization with Boc-tyrosine. The procedure utilized preparative hydrazinolysis to release the oligosaccharide and yielded multi-micromol quantities of Boc-tyrosine-Man9 which was characterized by 1H NMR and ES-MS. Copyright 1998 Academic Press.

Train hard, sleep well? Perceived training load, sleep quantity and sleep stage distribution in elite level athletes.

Science.gov (United States)

Knufinke, Melanie; Nieuwenhuys, Arne; Geurts, Sabine A E; Møst, Els I S; Maase, Kamiel; Moen, Maarten H; Coenen, Anton M L; Kompier, Michiel A J

2018-04-01

Sleep is essential for recovery and performance in elite athletes. While it is generally assumed that exercise benefits sleep, high training load may jeopardize sleep and hence limit adequate recovery. To examine this, the current study assessed objective sleep quantity and sleep stage distributions in elite athletes and calculated their association with perceived training load. Mixed-methods. Perceived training load, actigraphy and one-channel EEG recordings were collected among 98 elite athletes during 7 consecutive days of regular training. Actigraphy revealed total sleep durations of 7:50±1:08h, sleep onset latencies of 13±15min, wake after sleep onset of 33±17min and sleep efficiencies of 88±5%. Distribution of sleep stages indicated 51±9% light sleep, 21±8% deep sleep, and 27±7% REM sleep. On average, perceived training load was 5.40±2.50 (scale 1-10), showing large daily variability. Mixed-effects models revealed no alteration in sleep quantity or sleep stage distributions as a function of day-to-day variation in preceding training load (all p's>.05). Results indicate healthy sleep durations, but elevated wake after sleep onset, suggesting a potential need for sleep optimization. Large proportions of deep sleep potentially reflect an elevated recovery need. With sleep quantity and sleep stage distributions remaining irresponsive to variations in perceived training load, it is questionable whether athletes' current sleep provides sufficient recovery after strenuous exercise. Copyright © 2017 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

29 CFR 780.814 - “Grown in commercial quantities.”

Science.gov (United States)

2010-07-01

... OF GENERAL POLICY OR INTERPRETATION NOT DIRECTLY RELATED TO REGULATIONS EXEMPTIONS APPLICABLE TO AGRICULTURE, PROCESSING OF AGRICULTURAL COMMODITIES, AND RELATED SUBJECTS UNDER THE FAIR LABOR STANDARDS ACT... “commercial” quantities, the trade understanding of what are “commercial” quantities of cotton would be...

Preparation of additional supplies of 244Pu

International Nuclear Information System (INIS)

Bigelow, J.E.; Newman, E.; Alexander, C.W.

1985-01-01

In the mid-1970s, gram quantities of the man-made isotope 244 Pu were produced in high purity for basic research as a by-product of a program to prepare gram quantities of 252 Cf. Because 244 Pu is not produced in appreciable quantities in standard power reactor fuel, this nuclide has become extremely useful in the application of isotope dilution mass spectrometry (IDMS), a high-precision analytical technique, to problems of plutonium accountability in support of international safeguards agreements. Although only a small amount (a fraction of a microgram) is needed for each analysis, the present supply of certified nuclear reference standard SRM-996 is expected to last only an additional 3 to 5 years. Three options for producing additional supplies of this rare and valuable material were examined. The options encompassed the production of from 1 to 8.5 g during time spans of from 3 to 10 years. Unit costs ranged from $2300 to $7200 per mg of plutonium of >97% 244 Pu. While the paper concludes that the short-term option can be pursued along with further study of the longer-term options, this should not be regarded as an offer or a commitment on the part of the US Department of Energy (USDOE) to furnish the described material

Large Electrocaloric Effect in Lead-Free (Ba0.85Ca0.15)(Zr0.1Ti0.9)O3 Ceramics Prepared via Citrate Route

Science.gov (United States)

Shi, Jing; Zhu, Rongfeng; Liu, Xing; Yuan, Ningyi; Ding, Jianning; Luo, Haosu

2017-01-01

The 1 wt % Li-doped (Ba0.85Ca0.15)(Zr0.1Ti0.9)O3 (BCZT-Li) ceramics prepared by the citrate method exhibit improved phase purity, densification and electrical properties, which provide prospective possibility to develop high-performance electrocaloric materials. The electrocaloric effect was evaluated by phenomenological method, and the BCZT-Li ceramics present large electrocaloric temperature change ∆T, especially large electrocaloric responsibility ξ = ∆Tmax/∆Emax, which can be comparable to the largest values reported in the lead-free piezoelectric ceramics. The excellent electrocaloric effect is considered as correlating with the coexistence of polymorphic ferroelectric phases, which are detected by the Raman spectroscopy. The large ξ value accompanied by decreased Curie temperature (around 73 °C) of the BCZT-Li ceramics prepared by the citrate method presents potential applications as the next-generation solid-state cooling devices. PMID:28927004

Large Electrocaloric Effect in Lead-Free (Ba0.85Ca0.15(Zr0.1Ti0.9O3 Ceramics Prepared via Citrate Route

Directory of Open Access Journals (Sweden)

Jing Shi

2017-09-01

Full Text Available The 1 wt % Li-doped (Ba0.85Ca0.15(Zr0.1Ti0.9O3 (BCZT-Li ceramics prepared by the citrate method exhibit improved phase purity, densification and electrical properties, which provide prospective possibility to develop high-performance electrocaloric materials. The electrocaloric effect was evaluated by phenomenological method, and the BCZT-Li ceramics present large electrocaloric temperature change ∆T, especially large electrocaloric responsibility ξ = ∆Tmax/∆Emax, which can be comparable to the largest values reported in the lead-free piezoelectric ceramics. The excellent electrocaloric effect is considered as correlating with the coexistence of polymorphic ferroelectric phases, which are detected by the Raman spectroscopy. The large ξ value accompanied by decreased Curie temperature (around 73 °C of the BCZT-Li ceramics prepared by the citrate method presents potential applications as the next-generation solid-state cooling devices.

Preparation and Characterization of a Solid Acid Catalyst from Macro Fungi Residue for Methyl Palmitate Production

Directory of Open Access Journals (Sweden)

Min Wang

2015-07-01

Full Text Available During the process of fungal polysaccharide extraction for health care products and food factories, a large quantity of macro-fungi residues are produced, but most of the residues are abandoned and become environmental pollutants. A solid acid catalyst, prepared by sulfonating carbonized Phellinus igniarius residue, was shown to be an efficient and environmentally benign catalyst for the esterification of palmitate acid (PA and methanol. As a comparison, two types of common biomass catalysts, wheat straws and wood chips, were prepared. In this study, characterizations, including scanning electron microscopy, thermo-gravimetric analysis, Fourier transform infrared spectrometry, Brunauer-Emmett-Teller assays and elemental analysis, and reaction conditions for the synthesis of methyl palmitate (MP using solid acid catalysts were investigated. Experiments showed that the solid acid catalyst prepared from P. igniarius residue had a higher catalytic activity than the other two catalysts, and the highest yield of MP catalyzed by P. igniarius residue solid acid catalyst was 91.5% under the following optimum conditions: molar ratio of methanol/PA of 10:1, reaction temperature of 60 °C, mass ratio of catalyst/substrate of 2%, and a reaction time of 1.5 h. Thus, the use of this catalyst offers a method for producing MP.

Preparation of nuclear purity beryllium oxalate tri-hydrate; Preparation d'oxalate de beryllium trihydrate de purete nucleaire

Energy Technology Data Exchange (ETDEWEB)

Delcorte, M; Lecocq, A; Rigaud, A [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1964-07-01

In this report we have gathered the whole of the knowledge acquired by our group during the campaign for preparation of beryllium oxalate we carried out through the first half year of 1962. The reader shall find in the first place information and bibliographic data gathered by Miss OLLIVIER, documentalist of the Section d'Etudes, Recherches et Applications Chimiques. We then describe the original process perfected in the laboratories, and the production techniques we employed for the semi-large operative units. Finally, we publish the results we obtained on one hand on the chemical aspect, in the industrial meaning of the term, which is to-day concerning the ponderal output, on the other hand on the analytical aspect as you can evidently not dissociate the quantity of substance produced from its purity. (authors) [French] Nous avons reuni dans ce document l'ensemble des connaissances acquises par notre groupe pendant la campagne de preparation d'oxalate de beryllium que nous avons effectuee au cours du 1er semestre 1962. Le lecteur y trouvera en premier lieu les renseignements et donnees bibliographiques rassembles par Mlle OLLIVIER, documentaliste a la Section d'Etudes, Recherches et Applications Chimiques. Nous decrivons ensuite le procede original mis au point dans les laboratoires et les techniques de fabrication que nous avons utilisees pour des unites operatoires demi-grand. Pour terminer nous publions les resultats obtenus, d'une part sur le plan chimique, au sens industriel du terme, c'est-a-dire du point de vue rendement ponderal, d'autre part sur le plan analytique puisqu'on ne peut evidemment pas dissocier la quantite de produit fabrique, de sa purete. (auteurs)

Radiation quantities and units. ICRU report 33

International Nuclear Information System (INIS)

Anon.

1987-01-01

This report supersedes ICRU Report 19. Since ICRU Report 19 was published, a number of discussions have taken place between members of the Report Committee on Fundamental Quantities and Units and other workers in the field. Some of these discussions have resulted in the acceptance of certain modifications in the material set out in Report 19 and these modifications are incorporated in the current report. In addition, there has been some expansion and rearrangement of the material in the earlier report. It is recommended that energy state be inserted into the definition of activity and that the word transformation be replaced by transition. These modifications have now been incorporated into the current definition. Helpful comments on the previous quantities and units report have resulted in clarification of several points in the present Report. In line with providing more didactic material and useful source material for other ICRU reports, the general considerations in subsection I.A of Report 19 have been expanded and placed in a separate subsection. The additional material includes discussions of four terms that are used in this document - quantity, unit, stochastic, and non-stochastic - along with a brief discussion of the mathematical formalism used in ICRU reports. 11 refs., 4 tabs

SU-E-T-235: Data Mining for Evaluating Treatment Performances Over a Large Quantity of Data to Monitor and Improve SBRT Workflow

Energy Technology Data Exchange (ETDEWEB)

Feng, W [Columbia University Medical Center, New York, NY (United States); Bayhealth Medical Center, Dover, DE (United States); Chu, A [New York Presbyterian Hospital, New York, AA (United States); Wuu, C [Columbia University, New York, NY (United States); Nguyen, K [Bayhealth Medical Center, Dover, DE (United States)

2015-06-15

Purpose: To quality assure a large quantity of retrospective treatment cases for treatment performances by randomly sampling is inefficient. Here we provide a method to efficiently monitor and investigate the QA of SBRT workflow over Mosaiq. Methods: The code developed with Microsoft SQL Server Management Studio 2008R2 and VBA was used for retrieving and sorting data from Mosaiq (version 2.3–2.6 during 2012–2015). SBRT patients were filtered by fractional dose over 350cGy and total fraction number less than 6, which SBRT prescriptions were defined. The quality assurance on the SBRT workflow was focused on the treatment deliveries such as patient positioning setup, CBCT indicated offsets and couch shifted corrections. The treatment delivery were done by Varian Truebeam systems and the record/verify by Mosaiq. Results: Total 82 SBRT patients corresponding to 103 courses and 854 CBCT images were found by the retrieval query. Most centers record daily pre-treatment (Pre-Tx: before treatment shift) image-guided shifts along treatment course for inter-fraction motion record, and it is useful to also verify it with post-treatment imaging (Post-Tx: after treatment CBCT verification) to verify intra-fraction motion. Analyzing the details of daily recorded shifts can reveals the information of patient-setup and staff’s record/verify behaviors. 3 examples were provided as solid evidences and on-going rectification for preventing future mistakes. Conclusions: The report gave feasible examples for inspector to verify a large amount of data during site investigation. This program can also be extended to a scheduled data mining with software to periodical analyze the timely records in Mosaiq, for example, a various control charts for different QA purposes. As the current trend of automation in radiation therapy field, the data mining would be a necessary tool in the future, just as the automatic plan quality evaluation has been under development in Eclipse.

SU-E-T-235: Data Mining for Evaluating Treatment Performances Over a Large Quantity of Data to Monitor and Improve SBRT Workflow

International Nuclear Information System (INIS)

Feng, W; Chu, A; Wuu, C; Nguyen, K

2015-01-01

Purpose: To quality assure a large quantity of retrospective treatment cases for treatment performances by randomly sampling is inefficient. Here we provide a method to efficiently monitor and investigate the QA of SBRT workflow over Mosaiq. Methods: The code developed with Microsoft SQL Server Management Studio 2008R2 and VBA was used for retrieving and sorting data from Mosaiq (version 2.3–2.6 during 2012–2015). SBRT patients were filtered by fractional dose over 350cGy and total fraction number less than 6, which SBRT prescriptions were defined. The quality assurance on the SBRT workflow was focused on the treatment deliveries such as patient positioning setup, CBCT indicated offsets and couch shifted corrections. The treatment delivery were done by Varian Truebeam systems and the record/verify by Mosaiq. Results: Total 82 SBRT patients corresponding to 103 courses and 854 CBCT images were found by the retrieval query. Most centers record daily pre-treatment (Pre-Tx: before treatment shift) image-guided shifts along treatment course for inter-fraction motion record, and it is useful to also verify it with post-treatment imaging (Post-Tx: after treatment CBCT verification) to verify intra-fraction motion. Analyzing the details of daily recorded shifts can reveals the information of patient-setup and staff’s record/verify behaviors. 3 examples were provided as solid evidences and on-going rectification for preventing future mistakes. Conclusions: The report gave feasible examples for inspector to verify a large amount of data during site investigation. This program can also be extended to a scheduled data mining with software to periodical analyze the timely records in Mosaiq, for example, a various control charts for different QA purposes. As the current trend of automation in radiation therapy field, the data mining would be a necessary tool in the future, just as the automatic plan quality evaluation has been under development in Eclipse

Trained Quantity Abilities in Horses (Equus caballus: A Preliminary Investigation

Directory of Open Access Journals (Sweden)

Maria Elena Miletto Petrazzini

2014-07-01

Full Text Available Once believed to be a human prerogative, the capacity to discriminate between quantities now has also been reported in several vertebrates. To date, only two studies investigated numerical abilities in horses (Equus caballus but reported contrasting data. To assess whether horses can be trained to discriminate between quantities, I have set up a new experimental protocol using operant conditioning. One adult female was trained to discriminate between 1 and 4 (Test 1 in three different conditions: non-controlled continuous variables (numerical and continuous quantities that co-vary with number are simultaneously available, 50% controlled continuous variables (intermediate condition, and 100% controlled continuous variables (only numerical information available. The subject learned the discrimination in all conditions, showing the capacity to process numerical information. When presented with a higher numerical ratio (2 vs. 4, Test 2, the subject still discriminated between the quantities but its performance was statistically significant only in the non-controlled condition, suggesting that the subject used multiple cues in presence of a more difficult discrimination. On the whole, the results here reported encourage the use of this experimental protocol as a valid tool to investigate the capacity to process numerical and continuous quantities in horses in future research.

On the Output-Inflation Relationship When Price and Quantity Adjustments are Costly

DEFF Research Database (Denmark)

Danziger, Leif; Kreiner, Claus Thustrup

A vast literature analyzes the real effects of price-adjustment costs assuming that quantity adjustments are costless. In this paper, we analyze whether the presence of quantity-adjustments costs, which presumably are significant, change the traditional results on the impact of inflation....... In particular, recent findings suggest that quantity-adjustment costs may remove the linkage between output and inflation. We show that this is not the case when inflation is anticipated. On the contrary, quantity-adjustment costs may significantly amplify the consequences of price-adjustment costs...

Entropy and Its Correlations with Other Related Quantities

Directory of Open Access Journals (Sweden)

Jing Wu

2014-02-01

Full Text Available In order to find more correlations between entropy and other related quantities, an analogical analysis is conducted between thermal science and other branches of physics. Potential energy in various forms is the product of a conserved extensive quantity (for example, mass or electric charge and an intensive quantity which is its potential (for example, gravitational potential or electrical voltage, while energy in specific form is a dissipative quantity during irreversible transfer process (for example mechanical or electrical energy will be dissipated as thermal energy. However, it has been shown that heat or thermal energy, like mass or electric charge, is conserved during heat transfer processes. When a heat transfer process is for object heating or cooling, the potential of internal energy U is the temperature T and its potential “energy” is UT/2 (called entransy and it is the simplified expression of thermomass potential energy; when a heat transfer process is for heat-work conversion, the potential of internal energy U is (1 − T0/T, and the available potential energy of a system in reversible heat interaction with the environment is U − U0 − T0(S − S0, then T0/T and T0(S − S0 are the unavailable potential and the unavailable potential energy of a system respectively. Hence, entropy is related to the unavailable potential energy per unit environmental temperature for heat-work conversion during reversible heat interaction between the system and its environment. Entropy transfer, like other forms of potential energy transfer, is the product of the heat and its potential, the reciprocal of temperature, although it is in form of the quotient of the heat and the temperature. Thus, the physical essence of entropy transfer is the unavailable potential energy transfer per unit environmental temperature. Entropy is a non-conserved, extensive, state quantity of a system, and entropy generation in an irreversible heat transfer process

Nucleon-deuteron breakup quantities calculated with separable interactions including tensor forces and P-wave interactions

International Nuclear Information System (INIS)

Bruinsma, J.; Wageningen, R. van

1977-01-01

Nucleon-deuteron breakup calculations at a nucleon bombarding energy of 22.7 MeV have been performed with separable interactions including a tensor force and P-wave interactions. Differential cross sections and a selection of polarization quantities have been computed for special regions of the phase space. The influence of a tensor force and P-wave interactions on the differential cross section is of the order of 20%. Large discrepancies between theory and experiment occur for the vector analyzing powers, both for the kinematically complete and for the incomplete situation. The calculations show that there are kinematical situations in which the differential cross sections and the tensor analyzing powers are sufficiently large to make measurements feasible. (Auth.)

Preparation of coal slurries deposited in ground settling ponds

Directory of Open Access Journals (Sweden)

Wiesław Blaschke

2005-11-01

Full Text Available As a result of the hard coal washing process, considerable quantities of coal slimes are generated. They belong to grain size classes below 1, 0 mm (with the majority of grains below 0,035 mm and are often sold in order to prepare blends for the power generation. It is assessed that in Poland about 11 mln tons of such slimes were deposited. The slimes of a low ash content can be exploited and sold. The slime of high ash content must be washed. In Poland there is one coal preparation plant for slurries. The article describes the technology and presents the results of a simplified economic analysis of exploitation of the slurries and their washing.

Import and export of small quantities of nuclear materials

International Nuclear Information System (INIS)

Grenier, M.

1986-06-01

Administrative procedures for import export of nuclear materials are specific for each country. In France regulations are reviewed for small quantities, lower threshold, in some cases, allows a simplified procedure, however thresholds are not the same in the different texts (and for one of them, concerning proliferation, is zero). It is obvious that regulations are necessary even for small quantities but national and international threshold should be harmonized [fr

7 CFR 35.13 - Minimum quantity.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Minimum quantity. 35.13 Section 35.13 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... part, transport or receive for transportation to any foreign destination, a shipment of 25 packages or...

Test Station for Magnetization Measurements on Large Quantities of Superconducting Strands

CERN Document Server

Le Naour, S; Billan, J; Genest, J

2001-01-01

In the superconducting main magnets of the Large Hadron Collider (LHC), persistent currents in the superconductor determine the field quality at injection field. For this reason it is necessary to check the magnetization of the cable strands during their production. During four years, this requires measurements of the width of the strand magnetization hysteresis loop at 0.5 T, 1.9 K, at a rate of up to eight samples per day. This paper describes the design, construction and the first results of a magnetization test station built for this purpose. The samples are cooled in a cryostat, with a 2-m long elliptic tail. This tail is inserted in a normal conducting dipole magnet with a field between ± 1.5 T. Racetrack pick-up coils, integrated in the cryostat, detect the voltage due to flux change, which is then integrated numerically. The sample holder can contain eight strand samples, each 20 cm long. The test station operates in two modes: either the sample is fixed while the external field is changed, or the sa...

Soil fungal communities in a Castanea sativa (chestnut) forest producing large quantities of Boletus edulis sensu lato (porcini): where is the mycelium of porcini?

Science.gov (United States)

Peintner, Ursula; Iotti, Mirco; Klotz, Petra; Bonuso, Enrico; Zambonelli, Alessandra

2007-04-01

A study was conducted in a Castanea sativa forest that produces large quantities of the edible mushroom porcini (Boletus edulis sensu lato). The primary aim was to study porcini mycelia in the soil, and to determine if there were any possible ecological and functional interactions with other dominant soil fungi. Three different approaches were used: collection and morphological identification of fruiting bodies, morphological and molecular identification of ectomycorrhizae by rDNA-ITS sequence analyses and molecular identification of the soil mycelia by ITS clone libraries. Soil samples were taken directly under basidiomes of Boletus edulis, Boletus aestivalis, Boletus aereus and Boletus pinophilus. Thirty-nine ectomycorrhizal fungi were identified on root tips whereas 40 fungal species were found in the soil using the cloning technique. The overlap between above- and below-ground fungal communities was very low. Boletus mycelia, compared with other soil fungi, were rare and with scattered distribution, whereas their fruiting bodies dominated the above-ground fungal community. Only B. aestivalis ectomycorrhizae were relatively abundant and detected as mycelia in the soil. No specific fungus-fungus association was found. Factors triggering formation of mycorrhizae and fructification of porcini appear to be too complex to be simply explained on the basis of the amount of fungal mycelia in the soil.

Thermal Stability of Ultrafine Grained Pure Copper Prepared by Large Strain Extrusion Machining

Directory of Open Access Journals (Sweden)

Bangxian Wu

2018-05-01

Full Text Available Ultrafine grained (UFG pure copper chips with improved material strength have been successfully prepared by large strain extrusion machining (LSEM. However, the thermal stability of the UFG chips has been a key characteristic that has restricted their use in practical applications. To understand the influence of annealing temperature and annealing time on their microstructures and mechanical properties, the UFG chips were subjected to isochronous and isothermal annealing treatments as well as Vickers hardness tests in the present study. From the results, we found that the UFG chips maintain high hardness when annealing at temperatures up to 160 °C but begin to exhibit a reduction in their hardness while the annealing temperature reached above 200 °C. When annealed at 280 °C for 10–240 min, the grain size increased slightly and reached a stable value of 2 µm with an increase in annealing time and with a decrease in the hardness of the chips. These results indicated that UFG pure copper chips have good thermal stability at temperatures below 160 °C.

Large-scale generation of cell-derived nanovesicles

Science.gov (United States)

Jo, W.; Kim, J.; Yoon, J.; Jeong, D.; Cho, S.; Jeong, H.; Yoon, Y. J.; Kim, S. C.; Gho, Y. S.; Park, J.

2014-09-01

Exosomes are enclosed compartments that are released from cells and that can transport biological contents for the purpose of intercellular communications. Research into exosomes is hindered by their rarity. In this article, we introduce a device that uses centrifugal force and a filter with micro-sized pores to generate a large quantity of cell-derived nanovesicles. The device has a simple polycarbonate structure to hold the filter, and operates in a common centrifuge. Nanovesicles are similar in size and membrane structure to exosomes. Nanovesicles contain intracellular RNAs ranging from microRNA to mRNA, intracellular proteins, and plasma membrane proteins. The quantity of nanovesicles produced using the device is 250 times the quantity of naturally secreted exosomes. Also, the quantity of intracellular contents in nanovesicles is twice that in exosomes. Nanovesicles generated from murine embryonic stem cells can transfer RNAs to target cells. Therefore, this novel device and the nanovesicles that it generates are expected to be used in exosome-related research, and can be applied in various applications such as drug delivery and cell-based therapy.

A Little Here, A Little There, A Fairly Big Problem Everywhere: Small Quantity Site Transuranic Waste Disposition Alternatives

International Nuclear Information System (INIS)

Luke, Dale Elden; Parker, Douglas Wayne; Moss, J.; Monk, Thomas Hugh; Fritz, Lori Lee; Daugherty, B.; Hladek, K.; Kosiewicx, S.

2000-01-01

Small quantities of transuranic (TRU) waste represent a significant challenge to the waste disposition and facility closure plans of several sites in the Department of Energy (DOE) complex. This paper presents the results of a series of evaluations, using a systems engineering approach, to identify the preferred alternative for dispositioning TRU waste from small quantity sites (SQSs). The TRU waste disposition alternatives evaluation used semi-quantitative data provided by the SQSs, potential receiving sites, and the Waste Isolation Pilot Plant (WIPP) to select and recommend candidate sites for waste receipt, interim storage, processing, and preparation for final disposition of contact-handled (CH) and remote-handled (RH) TRU waste. The evaluations of only four of these SQSs resulted in potential savings to the taxpayer of $33 million to $81 million, depending on whether mobile systems could be used to characterize, package, and certify the waste or whether each site would be required to perform this work. Small quantity shipping sites included in the evaluation included the Battelle Columbus Laboratory (BCL), University of Missouri Research Reactor (MURR), Energy Technology Engineering Center (ETEC), and Mound. Candidate receiving sites included the Idaho National Engineering and Environmental Laboratory (INEEL), the Savannah River Site (SRS), Los Alamos National Laboratory (LANL), Oak Ridge (OR), and Hanford. At least 14 additional DOE sites having TRU waste may be able to save significant money if cost savings are similar to the four evaluated thus far

A little here, a little there, a fairly big problem everywhere: Small-quantity-site transuranic waste disposition alternatives

International Nuclear Information System (INIS)

D. Luke; D. Parker; J. Moss; T. Monk; L. Fritz; B. Daugherty; K. Hladek; S. Kosiewicx

2000-01-01

Small quantities of transuranic (TRU) waste represent a significant challenge to the waste disposition and facility closure plans of several sites in the Department of Energy (DOE) complex. This paper presents the results of a series of evaluations, using a systems engineering approach, to identify the preferred alternative for dispositioning TRU waste from small quantity sites (SQSs). The TRU waste disposition alternatives evaluation used semi-quantitative data provided by the SQSs, potential receiving sites, and the Waste Isolation Pilot Plant (WIPP) to select and recommend candidate sites for waste receipt, interim storage, processing, and preparation for final disposition of contact-handled (CH) and remote-handled (RH) TRU waste. The evaluations of only four of these SQSs resulted in potential savings to the taxpayer of $33 million to $81 million, depending on whether mobile systems could be used to characterize, package, and certify the waste or whether each site would be required to perform this work. Small quantity shipping sites included in the evaluation included the Battelle Columbus Laboratory (BCL), University of Missouri Research Reactor (MURR), Energy Technology Engineering Center (ETEC), and Mound Laboratory. Candidate receiving sites included the Idaho National Engineering and Environmental Laboratory (INEEL), the Savannah River Site (SRS), Los Alamos National Laboratory (LANL), Oak Ridge (OR), and Hanford. At least 14 additional DOE sites having TRU waste may be able to save significant money if cost savings are similar to the four evaluated thus far

Relationship between the partial molar and molar quantity of a thermodynamic state function in a multicomponent mixture – revisited

International Nuclear Information System (INIS)

Näfe, H.

2013-01-01

As far as a multicomponent mixture is concerned, different versions exist in the literature for the relationship between the partial molar and molar quantity of a thermodynamic state function with the most prominent example of the two quantities being the activity coefficient of an arbitrary component and the excess Gibbs free energy of a mixture comprising this component. Since the relationships published so far have to a large degree been derived independently of each other and result from apparently conflicting approaches, they are still considered as separate subjects in the literature. It is demonstrated that despite this curious situation all relationships are equivalent to each other from a mathematical point of view

Process of quantity determination of uranium by chromatography in liquid zone

International Nuclear Information System (INIS)

Muller, J.P.; Cojean, J.; Daubizit, M.

1993-01-01

The invention concerns a process of quantity determination of uranium by chromatography in liquid zone, usable to determine the quantity of uranium traces. Solutions to be treated can be aqueous or organic

The result of very small quantity of ETA injection program in Tomari Unit 1

International Nuclear Information System (INIS)

Echigoya, Koji

1998-01-01

In Tomari Nuclear Power Station, iron concentration reduction of feed water is quite important subject to maintain the integrity of Steam Generator (SG) heat transfer tubes. Water chemistry of BOP in Tomari is all volatile treatment (AVT) to adjust pH=9.3 in feed water as NH 3 and 0.3ppm N 2 H 4 . In order to reduce iron concentration, two water chemical methodologies are applied internationally in commercial plants, namely high AVT and advanced amine treatment. Tomari has some copper bearing materials in BOP heat exchangers, therefore high AVT is not able to be applied without large scale replacement of copper bearing materials. Tomari flow full condensate water for Condensate Demineralizing polisher and furthermore has an environmental regulation of COD concentration in disposable waste water, therefore advanced amine treatments are restricted in the upper limit of amines concentration unless Condensate Demineralizing System (CDS) and disposal waste water treatment system are largely improved. Consequently, very small quantity of ETA injection to present AVT was the most effective for Tomari condition, so the injection of very small quantity of ETA program in Tomari Unit-1 was tested. The test resulted in 20-30% reduction effect of iron concentration in the secondary feed water system, especially 50% reduction in steam/water two phase flow at maximum. This paper reports the outline and prospect of ETA injection program in Tomari. (J.P.N.)

Association between work-family conflict and smoking quantity among daily smokers.

Science.gov (United States)

Macy, Jonathan T; Chassin, Laurie; Presson, Clark C

2013-11-01

Recent work demonstrated a direct relation between work-family conflict and likelihood of smoking. This study furthered this area of research by (a) testing the association between work-family conflict and smoking quantity and (b) testing demographic, workplace, and home factors as moderators of this relation. Participants (N = 423) were daily smokers from a Midwestern community-based sample. Ordinal regression analysis tested work-to-home and home-to-work conflict as predictors (after controlling for demographic characteristics, home factors, and workplace factors) of smoking quantity. Additionally, we tested whether the demographic, home, and workplace factors moderated the effects of work-to-home conflict and home-to-work conflict on smoking quantity. Males (OR = 8.81, p = .005), older participants (OR = 1.09, p = .012), those with less educational attainment (OR = 1.87, p = .001), those who reported lower levels of workplace smoking restrictions (OR = 0.87, p = .019), and those who reported higher levels of work-to-home conflict (OR = 1.39, p = .026) smoked more cigarettes per day. There was no significant main effect of home-to-work conflict on smoking quantity (OR = 1.46, p = .099). A significant interaction (OR = 0.55, p = .043) revealed that home-to-work conflict was associated with smoking quantity for females but not for males. After controlling for demographic characteristics and potential confounders, work-to-home conflict had a negative impact on smoking quantity for all participants, and home-to-work conflict was associated with smoking quantity for women. Workplace wellness programs to reduce smoking among employees should take into account the direction of conflict and how the effect of the conflict on smoking behavior may vary based on other factors.

Quantities of natural gas transported in January-December 2009

International Nuclear Information System (INIS)

2010-01-01

GRTgaz is a European leader in natural gas transmission, a world expert in gas transmission networks and systems, and an operator firmly committed to the energy transition. It owns and operates the gas transmission network throughout most of France and it manages the transmission network in Germany, thereby helping to ensure correct operation of the French and European gas market. It contributes to the energy security of regional supply systems and performs a public service mission to ensure the continuity of consumer supply. This document presents the monthly key figures of GRTgaz activity in 2009: Total quantities transmitted by GRTgaz (Inputs to the GRTgaz network/Outputs from the GRTgaz network); Maximum and minimum daily flow (Daily quantities transported, Daily consumption, Daily inputs excluding storage); Quantities exchanged on the wholesale market; Consumption on the GRTgaz Network (gross monthly consumption and Average monthly temperatures)

High-throughput automated microfluidic sample preparation for accurate microbial genomics.

Science.gov (United States)

Kim, Soohong; De Jonghe, Joachim; Kulesa, Anthony B; Feldman, David; Vatanen, Tommi; Bhattacharyya, Roby P; Berdy, Brittany; Gomez, James; Nolan, Jill; Epstein, Slava; Blainey, Paul C

2017-01-27

Low-cost shotgun DNA sequencing is transforming the microbial sciences. Sequencing instruments are so effective that sample preparation is now the key limiting factor. Here, we introduce a microfluidic sample preparation platform that integrates the key steps in cells to sequence library sample preparation for up to 96 samples and reduces DNA input requirements 100-fold while maintaining or improving data quality. The general-purpose microarchitecture we demonstrate supports workflows with arbitrary numbers of reaction and clean-up or capture steps. By reducing the sample quantity requirements, we enabled low-input (∼10,000 cells) whole-genome shotgun (WGS) sequencing of Mycobacterium tuberculosis and soil micro-colonies with superior results. We also leveraged the enhanced throughput to sequence ∼400 clinical Pseudomonas aeruginosa libraries and demonstrate excellent single-nucleotide polymorphism detection performance that explained phenotypically observed antibiotic resistance. Fully-integrated lab-on-chip sample preparation overcomes technical barriers to enable broader deployment of genomics across many basic research and translational applications.

48 CFR 852.270-2 - Bread and bakery products-quantities.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Bread and bakery products... Bread and bakery products—quantities. As prescribed in 870.111-3, insert the following clause: Bread and Bakery Products—Quantities (JAN 2008) The bidder agrees to furnish up to 25 percent more or 25 percent...

A comparison of sample preparation strategies for biological tissues and subsequent trace element analysis using LA-ICP-MS.

Science.gov (United States)

Bonta, Maximilian; Török, Szilvia; Hegedus, Balazs; Döme, Balazs; Limbeck, Andreas

2017-03-01

Laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) is one of the most commonly applied methods for lateral trace element distribution analysis in medical studies. Many improvements of the technique regarding quantification and achievable lateral resolution have been achieved in the last years. Nevertheless, sample preparation is also of major importance and the optimal sample preparation strategy still has not been defined. While conventional histology knows a number of sample pre-treatment strategies, little is known about the effect of these approaches on the lateral distributions of elements and/or their quantities in tissues. The technique of formalin fixation and paraffin embedding (FFPE) has emerged as the gold standard in tissue preparation. However, the potential use for elemental distribution studies is questionable due to a large number of sample preparation steps. In this work, LA-ICP-MS was used to examine the applicability of the FFPE sample preparation approach for elemental distribution studies. Qualitative elemental distributions as well as quantitative concentrations in cryo-cut tissues as well as FFPE samples were compared. Results showed that some metals (especially Na and K) are severely affected by the FFPE process, whereas others (e.g., Mn, Ni) are less influenced. Based on these results, a general recommendation can be given: FFPE samples are completely unsuitable for the analysis of alkaline metals. When analyzing transition metals, FFPE samples can give comparable results to snap-frozen tissues. Graphical abstract Sample preparation strategies for biological tissues are compared with regard to the elemental distributions and average trace element concentrations.

Variation in Quantity of Heat Produced from Charcoal of Prosopis ...

African Journals Online (AJOL)

Data were collected using the copper calorimeter, a thermometer, an air tight burner and a weight balance. The results showed a gradual decrease in the quantity of heat produced as combustion time increased from 10 40 minutes in all wood species. Significant differences (p<0.05) in the quantity of heat produced both ...

Multimodal semantic quantity representations: further evidence from Korean Sign Language

Directory of Open Access Journals (Sweden)

Frank eDomahs

2012-01-01

Full Text Available Korean deaf signers performed a number comparison task on pairs of Arabic digits. In their RT profiles, the expected magnitude effect was systematically modified by properties of number signs in Korean Sign Language in a culture-specific way (not observed in hearing and deaf Germans or hearing Chinese. We conclude that finger-based quantity representations are automatically activated even in simple tasks with symbolic input although this may be irrelevant and even detrimental for task performance. These finger-based numerical representations are accessed in addition to another, more basic quantity system which is evidenced by the magnitude effect. In sum, these results are inconsistent with models assuming only one single amodal representation of numerical quantity.

The effects of quantity and depth of processing on children's time perception.

Science.gov (United States)

Arlin, M

1986-08-01

Two experiments were conducted to investigate the effects of quantity and depth of processing on children's time perception. These experiments tested the appropriateness of two adult time-perception models (attentional and storage size) for younger ages. Children were given stimulus sets of equal time which varied by level of processing (deep/shallow) and quantity (list length). In the first experiment, 28 children in Grade 6 reproduced presentation times of various quantities of pictures under deep (living/nonliving categorization) or shallow (repeating label) conditions. Students also compared pairs of durations. In the second experiment, 128 children in Grades K, 2, 4, and 6 reproduced presentation times under similar conditions with three or six pictures and with deep or shallow processing requirements. Deep processing led to decreased estimation of time. Higher quantity led to increased estimation of time. Comparative judgments were influenced by quantity. The interaction between age and depth of processing was significant. Older children were more affected by depth differences than were younger children. Results were interpreted as supporting different aspects of each adult model as explanations of children's time perception. The processing effect supported the attentional model and the quantity effect supported the storage size model.

Testing quantity theory of money for the Turkish economy

OpenAIRE

Levent, Korap

2007-01-01

In this paper, it is tried to test the main assumptions of the Quantity Theory of Money for the Turkish economy. Using some contemporaneous estimation techniques to examine the long-run stationary economic relationships on which the quantity theory is constructed, it is found that stationary characteristics of the velocitities of narrowly and broadly defined monetary aggregates cannot be rejected. However, monetary aggregates seem to be endogenous for the long-run evoluation of prices and rea...

Association Between Work–Family Conflict and Smoking Quantity Among Daily Smokers

Science.gov (United States)

2013-01-01

Introduction: Recent work demonstrated a direct relation between work–family conflict and likelihood of smoking. This study furthered this area of research by (a) testing the association between work–family conflict and smoking quantity and (b) testing demographic, workplace, and home factors as moderators of this relation. Methods: Participants (N = 423) were daily smokers from a Midwestern community-based sample. Ordinal regression analysis tested work-to-home and home-to-work conflict as predictors (after controlling for demographic characteristics, home factors, and workplace factors) of smoking quantity. Additionally, we tested whether the demographic, home, and workplace factors moderated the effects of work-to-home conflict and home-to-work conflict on smoking quantity. Results: Males (OR = 8.81, p = .005), older participants (OR = 1.09, p = .012), those with less educational attainment (OR = 1.87, p = .001), those who reported lower levels of workplace smoking restrictions (OR = 0.87, p = .019), and those who reported higher levels of work-to-home conflict (OR = 1.39, p = .026) smoked more cigarettes per day. There was no significant main effect of home-to-work conflict on smoking quantity (OR = 1.46, p = .099). A significant interaction (OR = 0.55, p = .043) revealed that home-to-work conflict was associated with smoking quantity for females but not for males. Conclusions: After controlling for demographic characteristics and potential confounders, work-to-home conflict had a negative impact on smoking quantity for all participants, and home-to-work conflict was associated with smoking quantity for women. Workplace wellness programs to reduce smoking among employees should take into account the direction of conflict and how the effect of the conflict on smoking behavior may vary based on other factors. PMID:23709611

Acid/base bifunctional carbonaceous nanomaterial with large surface area: Preparation, characterization, and adsorption properties for cationic and anionic compounds

Energy Technology Data Exchange (ETDEWEB)

Li, Kai; Ma, Chun–Fang; Ling, Yuan; Li, Meng [Department of Chemistry, Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074 (China); Gao, Qiang, E-mail: gaoqiang@cug.edu.cn [Department of Chemistry, Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074 (China); Engineering Research Center of Nano-Geo Materials of Ministry of Education, China University of Geosciences, Wuhan 430074 (China); Luo, Wen–Jun, E-mail: heartnohome@yahoo.com.cn [Department of Chemistry, Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074 (China)

2015-07-15

Nanostructured carbonaceous materials are extremely important in the nano field, yet developing simple, mild, and “green” methods that can make such materials possess large surface area and rich functional groups on their surfaces still remains a considerable challenge. Herein, a one-pot and environment-friendly method, i.e., thermal treatment (180 °C; 18 h) of water mixed with glucose and chitosan (CTS), has been proposed. The resultant carbonaceous nanomaterials were characterized by field emitting scanning electron microscope, N{sub 2} adsorption/desorption, Fourier transform infrared spectroscope, X-ray photoelectron spectroscopy, and zeta-potential analysis. It was found that, in contrast to the conventional hydrothermally carbonized product from pure glucose, with low surface area (9.3 m{sup 2} g{sup −1}) and pore volume (0.016 cm{sup 3} g{sup −1}), the CTS-added carbonaceous products showed satisfactory textural parameters (surface area and pore volume up to 254 m{sup 2} g{sup −1} and 0.701 cm{sup 3} g{sup −1}, respectively). Moreover, it was also interestingly found that these CTS-added carbonaceous products possessed both acidic (–COOH) and basic (–NH{sub 2}) groups on their surfaces. Taking the advantages of large surface area and –COOH/–NH{sub 2} bifunctional surface, the carbonaceous nanomaterials exhibited excellent performance for adsorptions of cationic compound (i.e., methylene blue) at pH 10 and anionic compound (i.e., acid red 18) at pH 2, respectively. This work not only provides a simple and green route to prepare acid/base bifunctional carbonaceous nanomaterials with large surface area but also well demonstrates their potential for application in adsorption. - Highlights: • A simple and green method was proposed to prepare carbon nanomaterials. • The carbon product showed acid/base bifunctional surface with large surface area. • The carbon material could efficiently adsorb both cationic and anionic compounds.

Quantities of natural gas transported in August-December 2007

International Nuclear Information System (INIS)

2008-01-01

GRTgaz is a European leader in natural gas transmission, a world expert in gas transmission networks and systems, and an operator firmly committed to the energy transition. It owns and operates the gas transmission network throughout most of France and it manages the transmission network in Germany, thereby helping to ensure correct operation of the French and European gas market. It contributes to the energy security of regional supply systems and performs a public service mission to ensure the continuity of consumer supply. This document presents the available monthly key figures of GRTgaz activity from August to December 2007: Total quantities transmitted by GRTgaz (Inputs to the GRTgaz network/Outputs from the GRTgaz network); Maximum and minimum daily flow (Daily quantities transported, Daily consumption, Daily inputs excluding storage); Quantities exchanged on the wholesale market; Consumption on the GRTgaz Network (gross monthly consumption and Average monthly temperatures)

Symbols and definitions of quantities and units in isotope stoichiometry

International Nuclear Information System (INIS)

Junghans, P.; Krumbiegel, P.; Faust, H.

1982-01-01

On the basis of the International System of Units and recent recommendations of the IUPAC on 'Symbols and Terminology for Physicochemical Quantities and Units' a system is proposed of uniform and unambiguous symbols and definitions of quantities and units used in the isotope dilution technique. The close relationship between isotope stoichiometry and common stoichiometry is demonstrated. (author)

Measurement of uranium quantities by fluorescence-X using neuronal techniques

International Nuclear Information System (INIS)

Vigneron, V.; Martinez, J.M.; Simon, A.C.; Junca, R.

1995-01-01

Layered neural networks are a class of models based on neural computation in biological systems. Connexionists models are made of a large number of simple computing structures, highly interconnected. The weights assigned to the connections enable the encoding of the knowledge required for a task. They can be trained to learn any input-output relation after selecting a suitable architecture. This method appears useful in those cases in which a simple operation and a fast response are needed, together with a reasonable accuracy. They are applied here to the automatic analysis of X-ray fluorescence spectra, obtained with plastic bottles irradiate by collimated beam of photons, emitted by a sealed source of iridium. The method could allow the surveillance of the measurement of uranium quantities in nuclear fuel cycles in processing plants. (authors). 11 refs., 4 figs

Varieties of Quantity Estimation in Children

Science.gov (United States)

Sella, Francesco; Berteletti, Ilaria; Lucangeli, Daniela; Zorzi, Marco

2015-01-01

In the number-to-position task, with increasing age and numerical expertise, children's pattern of estimates shifts from a biased (nonlinear) to a formal (linear) mapping. This widely replicated finding concerns symbolic numbers, whereas less is known about other types of quantity estimation. In Experiment 1, Preschool, Grade 1, and Grade 3…

Preparation of additional supplies of 244Pu

International Nuclear Information System (INIS)

Bigelow, J.E.; Newman, E.; Alexander, C.W.

1985-01-01

In the mid-1970s, gram quantities of the man-made isotope 244 Pu were produced in high purity for basic research as a by-product of a program to prepare gram quantities of 252 Cf. Because 244 Pu is not produced in appreciable quantities in standard power reactor fuel, this nuclide has become extremely useful in the application of isotope dilution mass spectrometry (IDMS), a high-precision analytical technique, to problems of plutonium accountability in support of international safeguards agreements. Although only a small amount (a fraction of a microgram) is needed for each analysis, the present supply of certified nuclear reference standard SRM-996 is expected to last only an additional 3 to 5 years. Three options for producing additional supplies of this rare and valuable material were examined. The options encompassed the production of from 1 to 8.5 g during time spans of from 3 to 10 years. Unit costs ranged from $2300 to $7200 per mg of plutonium of >97% 244 Pu. While the paper concludes that the short-term option can be pursued along with further study of the longer-term options, this should not be regarded as an offer or a commitment on the part of the U.S. Department of Energy (USDOE) to furnish the described material. (author)

40 CFR 273.8 - Applicability-household and conditionally exempt small quantity generator waste.

Science.gov (United States)

2010-07-01

... conditionally exempt small quantity generator waste. 273.8 Section 273.8 Protection of Environment ENVIRONMENTAL....8 Applicability—household and conditionally exempt small quantity generator waste. (a) Persons... universal wastes defined at § 273.9; and/or (2) Conditionally exempt small quantity generator wastes that...

The determination of trace quantities of thorium and uranium in thick ore samples by proton-induced x-ray emission

International Nuclear Information System (INIS)

Cohen, D.D.; Duerden, P.; Clayton, E.

1979-07-01

Proton-induced X-ray emission (PIXE) techniques have been used to estimate the concentrations of trace quantities of thorium and uranium in powdered rock and ore samples. Standards of known concentrations were prepared in a carbon matrix and the yields from these used to determine simultaneously the concentrations of thorium and uranium in the ore samples. The experimental detection limit of the technique was found to be 3 to 4 μg g -1 for a 100 μC irradiation. The appropriate matrix corrections for a carbon and ore matrix have been calculated for thick targets and taken into consideration

Large-scale synthesis of single-crystalline MgO with bone-like nanostructures

International Nuclear Information System (INIS)

Niu Haixia; Yang Qing; Tang Kaibin; Xie Yi

2006-01-01

Uniform bone-like MgO nanocrystals have been prepared via a solvothermal process using commercial Mg powders as the starting material in the absence of any catalyst or surfactant followed by a subsequent calcination. Field emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM) measurements indicate that the product consists of a large quantity of bone-like nanocrystals with lengths of 120-200 nm. The widths of these nanocrystals at both ends are in the range of 20-50 nm, which are 3-20 nm wider than those of the middle parts. Explorations of X-ray diffraction (XRD) and selected area electronic diffraction (SAED) exhibit that the product is high-quality cubic single-crystalline nanocrystals. The photoluminescence (PL) measurement suggests that the product has an intensive emission centered at 410 nm, showing that the product has potential application in optical devices. The advantages of our method lie in high yield, the easy availability of the starting materials and permitting large-scale production at low cost. The growth mechanism was proposed to be related with solvent's oxidation in the precursor formation process and following nucleation and mass-transfer in the decomposition of the precursor

New materials for sample preparation techniques in bioanalysis.

Science.gov (United States)

Nazario, Carlos Eduardo Domingues; Fumes, Bruno Henrique; da Silva, Meire Ribeiro; Lanças, Fernando Mauro

2017-02-01

The analysis of biological samples is a complex and difficult task owing to two basic and complementary issues: the high complexity of most biological matrices and the need to determine minute quantities of active substances and contaminants in such complex sample. To succeed in this endeavor samples are usually subject to three steps of a comprehensive analytical methodological approach: sample preparation, analytes isolation (usually utilizing a chromatographic technique) and qualitative/quantitative analysis (usually with the aid of mass spectrometric tools). Owing to the complex nature of bio-samples, and the very low concentration of the target analytes to be determined, selective sample preparation techniques is mandatory in order to overcome the difficulties imposed by these two constraints. During the last decade new chemical synthesis approaches has been developed and optimized, such as sol-gel and molecularly imprinting technologies, allowing the preparation of novel materials for sample preparation including graphene and derivatives, magnetic materials, ionic liquids, molecularly imprinted polymers, and much more. In this contribution we will review these novel techniques and materials, as well as their application to the bioanalysis niche. Copyright © 2016 Elsevier B.V. All rights reserved.

Characterization of the calcium-fluoroaluminosilicate glass prepared by a non-hydrolytic sol-gel route for future dental application as glass ionomer cement

Directory of Open Access Journals (Sweden)

Alexandre Cestari

2009-06-01

Full Text Available Glass ionomer cements are widely employed in dentistry due to their physical, biological and mainly anti-caries properties. Glass ionomers consist of an aluminosilicate glass matrix modified with other elements, and they contain large quantities of fluorine. In this study, we report on the preparation of calcium-fluoroaluminosilicate glasses by a nonhydrolytic sol-gel route as an alternative approach to obtaining alumina-silica matrices. The glass powders were prepared via the non-hydrolytic sol-gel method, by mixing AlCl3, SiCl4, CaF2, AlF3, NaF, and AlPO4. The powders were studied by thermal analysis (TG/DTA/DSC, photoluminescence (PL, nuclear magnetic resonance (NMR27Al-29Si, and X ray diffraction (XRD. TG/DTA/DSC analyses revealed a constant mass loss due to structural changes during the heating process, which was confirmed by NMR and PL. A stable aluminosilicate matrix with potential future application as a glass ionomer base was obtained.

Memory for multiple cache locations and prey quantities in a food-hoarding songbird

Directory of Open Access Journals (Sweden)

Nicola eArmstrong

2012-12-01

Full Text Available Most animals can discriminate between pairs of numbers that are each less than four without training. However, North Island robins (Petroica longipes, a food hoarding songbird endemic to New Zealand, can discriminate between quantities of items as high as eight without training. Here we investigate whether robins are capable of other complex quantity discrimination tasks. We test whether their ability to discriminate between small quantities declines with 1. the number of cache sites containing prey rewards and 2. the length of time separating cache creation and retrieval (retention interval. Results showed that subjects generally performed above chance expectations. They were equally able to discriminate between different combinations of prey quantities that were hidden from view in 2, 3 and 4 cache sites from between 1, 10 and 60 seconds. Overall results indicate that North Island robins can process complex quantity information involving more than two discrete quantities of items for up to one minute long retention intervals without training.

Charaterisation of function spaces via mollification; fractal quantities for distributions

Directory of Open Access Journals (Sweden)

Hans Triebel

2003-01-01

Full Text Available The aim of this paper is twofold. First we characterise elements f belonging to the Besov spaces Bpqs(ℝn with s∈ℝ,  0quantities for distributions generalising well-known corresponding quantities for Radon measures.

A facile and cost-effective approach to engineer surface roughness for preparation of large-scale superhydrophobic substrate with high adhesive force

Science.gov (United States)

Zhou, Bingpu; Tian, Jingxuan; Wang, Cong; Gao, Yibo; Wen, Weijia

2016-12-01

This study presents a convenient avenue to fabricate polydimethylsiloxane (PDMS) with controllable surface morphologies and wetting characteristics via standard molding technique. The templates with engineered surface roughness were simply prepared by combinations of microfluidics and photo-polymerization of N-Isopropylacrylamide (NIPAM). The surface morphology of mold could be adjusted via ultraviolet-curing duration or the grafting density, which means that the surface of PDMS sample replicated from the mold could also be easily controlled based on the proposed method. Furthermore, via multiple grafting and replication processes, we have successfully demonstrated that hydrophobicity properties of prepared PDMS samples could be swiftly enhanced to ∼154° with highly adhesive force with resident water droplets. The obtained PDMS samples exhibited well resistance to external mechanical deformation even up to 100 cycles. The proposed scheme is timesaving, cost-effective and suitable for large-scale production of superhydrophobic PDMS substrates. We believe that the presented approach can provide a promising method for preparing superhydrophobic surface with highly adhesive force for on-chip liquid transport, localized reaction, etc.

Prices versus Quantities

DEFF Research Database (Denmark)

Hansen, Lars Gårn; Jensen, Frank

illustrate that this result does not generalise to a search fishery, where marginal costs are allowed to depend on harvest. Hansen et al (2008) study a fishery where non-compliance with regulations is a problem. When the regulator is uncertain about non-compliance (compliance uncertainty), then landing fees......Weitzman (2002) studies the regulation of a fishery characterised by constant marginal harvest costs and shows that price regulation performs better than quantity regulation when the regulator is uncertain about the biological reproduction function (ecological uncertainty). Here, we initially...... are the preferred type of regulation, and Hansen et al (2008) find that this result does generalise to a search fishery where marginal costs depend on harvest. In this paper, we simulate a stochastic stock-recruitment model for the Danish cod fishery in the Kategat capturing both ecological and compliance...

Allen's astrophysical quantities

CERN Document Server

2000-01-01

This new, fourth, edition of Allen's classic Astrophysical Quantities belongs on every astronomer's bookshelf. It has been thoroughly revised and brought up to date by a team of more than ninety internationally renowned astronomers and astrophysicists. While it follows the basic format of the original, this indispensable reference has grown to more than twice the size of the earlier editions to accommodate the great strides made in astronomy and astrophysics. It includes detailed tables of the most recent data on: - General constants and units - Atoms, molecules, and spectra - Observational astronomy at all wavelengths from radio to gamma-rays, and neutrinos - Planetary astronomy: Earth, planets and satellites, and solar system small bodies - The Sun, normal stars, and stars with special characteristics - Stellar populations - Cataclysmic and symbiotic variables, supernovae - Theoretical stellar evolution - Circumstellar and interstellar material - Star clusters, galaxies, quasars, and active galactic nuclei ...

Preparation of freezing quantum state for quantum coherence

Science.gov (United States)

Yang, Lian-Wu; Man, Zhong-Xiao; Zhang, Ying-Jie; Han, Feng; Du, Shao-jiang; Xia, Yun-Jie

2018-06-01

We provide a method to prepare the freezing quantum state for quantum coherence via unitary operations. The initial product state consists of the control qubit and target qubit; when it satisfies certain conditions, the initial product state converts into the particular Bell diagonal state under the unitary operations, which have the property of freezing of quantum coherence under quantum channels. We calculate the frozen quantum coherence and corresponding quantum correlations, and find that the quantities are determined by the control qubit only when the freezing phenomena occur.

Advances in preparation and characterization of chitosan nanoparticles for therapeutics.

Science.gov (United States)

Chandra Hembram, Krushna; Prabha, Shashi; Chandra, Ramesh; Ahmed, Bahar; Nimesh, Surendra

2016-01-01

Polymers have been largely explored for the preparation of nanoparticles due to ease of preparation and modification, large gene/drug loading capacity, and biocompatibility. Various methods have been adapted for the preparation and characterization of chitosan nanoparticles. Focus on the different methods of preparation and characterization of chitosan nanoparticles. Detailed literature survey has been done for the studies reporting various methods of preparation and characterization of chitosan nanoparticles. Published database suggests of several methods which have been developed for the preparation and characterization of chitosan nanoparticles as per the application.

Variations of influence quantities in industrial irradiators and their effect on dosimetry performance

International Nuclear Information System (INIS)

Chu, R.D.H.

1999-01-01

Many environmental factors, including irradiation temperature, post-irradiation storage temperature, dose rate, relative humidity, oxygen content and the energy spectrum may affect the response of dosimetry systems used in industrial radiation processing. Although the effects of individual influence quantities have been extensively studied, the variations of these influence quantities in production irradiators and the complex relationships between the effects of different influence quantities make it difficult to assess the overall effect on the measurement uncertainty. In the development of new dosimetry systems it is important to know the effect of each influence quantity and developers of new dosimetry systems should perform studies over a wide range of irradiation conditions. Analysis parameters and manufacturing specifications should be chosen to minimize the effect of influence quantities in the environments where the dosimeters will be used. Because of possible relationships between different influence quantities, care must be taken to ensure that the response function determined in the calibration of the dosimetry system is applicable for the conditions in which the dosimeters will be used. Reference standard dosimetry systems which have been thoroughly studied and have known relationships between dose response and influence quantities should be used to verify the calibration of routine dosimetry systems under the actual conditions of use. Better understanding of the variations in influence quantities in industrial irradiators may be obtained by modeling or direct measurements and may provide improvements in the calibration of routine dosimetry system and reduction of the overall measurement uncertainty. (author)

Towards large-scale plasma-assisted synthesis of nanowires

Science.gov (United States)

Cvelbar, U.

2011-05-01

Large quantities of nanomaterials, e.g. nanowires (NWs), are needed to overcome the high market price of nanomaterials and make nanotechnology widely available for general public use and applications to numerous devices. Therefore, there is an enormous need for new methods or routes for synthesis of those nanostructures. Here plasma technologies for synthesis of NWs, nanotubes, nanoparticles or other nanostructures might play a key role in the near future. This paper presents a three-dimensional problem of large-scale synthesis connected with the time, quantity and quality of nanostructures. Herein, four different plasma methods for NW synthesis are presented in contrast to other methods, e.g. thermal processes, chemical vapour deposition or wet chemical processes. The pros and cons are discussed in detail for the case of two metal oxides: iron oxide and zinc oxide NWs, which are important for many applications.

Procedure for preparation of dispersions

International Nuclear Information System (INIS)

1978-01-01

Procedure for the preparation of a water based dispersion of cerium oxide, characterised in that a suspension of cerium (IV) hydroxide is formed with an acid, where the acid is in the state of a disaggregation of aggregated crystalline cerium hydroxide, the suspension being preheated for a specified time and to a specified temperature, so that the pH value becomes constant, and whereby the quantity of acid in the suspension is such that the constant pH value is lower than 5.4, so that a conditioned suspension may be obtained, and water may be mixed with the conditioned suspension for making a water based dispersion of cerium oxide. (G.C.)

Large-scale production and study of a synthetic G protein-coupled receptor: Human olfactory receptor 17-4

Science.gov (United States)

Cook, Brian L.; Steuerwald, Dirk; Kaiser, Liselotte; Graveland-Bikker, Johanna; Vanberghem, Melanie; Berke, Allison P.; Herlihy, Kara; Pick, Horst; Vogel, Horst; Zhang, Shuguang

2009-01-01

Although understanding of the olfactory system has progressed at the level of downstream receptor signaling and the wiring of olfactory neurons, the system remains poorly understood at the molecular level of the receptors and their interaction with and recognition of odorant ligands. The structure and functional mechanisms of these receptors still remain a tantalizing enigma, because numerous previous attempts at the large-scale production of functional olfactory receptors (ORs) have not been successful to date. To investigate the elusive biochemistry and molecular mechanisms of olfaction, we have developed a mammalian expression system for the large-scale production and purification of a functional OR protein in milligram quantities. Here, we report the study of human OR17-4 (hOR17-4) purified from a HEK293S tetracycline-inducible system. Scale-up of production yield was achieved through suspension culture in a bioreactor, which enabled the preparation of >10 mg of monomeric hOR17-4 receptor after immunoaffinity and size exclusion chromatography, with expression yields reaching 3 mg/L of culture medium. Several key post-translational modifications were identified using MS, and CD spectroscopy showed the receptor to be ≈50% α-helix, similar to other recently determined G protein-coupled receptor structures. Detergent-solubilized hOR17-4 specifically bound its known activating odorants lilial and floralozone in vitro, as measured by surface plasmon resonance. The hOR17-4 also recognized specific odorants in heterologous cells as determined by calcium ion mobilization. Our system is feasible for the production of large quantities of OR necessary for structural and functional analyses and research into OR biosensor devices. PMID:19581598

Patterns in new dimensionless quantities containing melting temperature, and their dependence on pressure

Directory of Open Access Journals (Sweden)

U. WALZER

1980-06-01

Full Text Available The relationships existing between melting temperature and other
macroscopic physical quantities are investigated. A new dimensionless
quantity Q(1 not containing the Grtineisen parameter proves to be suited for serving in future studies as a tool for the determination of the melting temperature in the outer core of the Earth. The pressure dependence of more general dimensionless quantities Q„ is determined analytically and, for the chemical elements, numerically, too. The patterns of various interesting dimensionless quantities are shown in the Periodic Table and compared.

A practical method for target preparation of powdered materials

International Nuclear Information System (INIS)

Sugai, Isao.

1977-01-01

This is the sixth report on the practical method of target preparation for use in nuclear physics experiments following the previous one (INS-TL-131, 1976). We have made various targets by developing the centrifugal precipitation method, which is particularly effective in the cases; (a) metal with high melting point and low vapor pressure, (b) oxides which are difficult to prepare by the usual vacuum evaporation technique and (c) some enriched isotopes which are very minute in quantity (less than - 10 mg) and low in recovery ratio. The samples were once suspended in liquid paraffin by ultrasonic wave vibrator, and then centrifugally precipitated on a thin backing foil such as Mylar or aluminum set and the bottom of the centrifugal tube. Uniformity of target made in this way was checked by an 24 Am-α ray thickness gauge. Contaminations smudged in the preparing process were checked by irradiating the targets with the proton beam from the FM Cyclotron at I.N.S. (auth.)

Recent progress on preparation and properties of nanocomposites from recycled polymers: A review

International Nuclear Information System (INIS)

Zare, Yasser

2013-01-01

Highlights: ► The article determines the current status of nanotechnology in polymer recycling. ► The addition of nanofillers to waste polymers, composites and blends is discussed. ► The future challenges in polymer recycling using nanoparticles are explained. - Abstract: Currently, the growing consumption of polymer products creates the large quantities of waste materials resulting in public concern in the environment and people life. Nanotechnology is assumed the important technology in the current century. Recently, many researchers have tried to develop this new science for polymer recycling. In this article, the application of different nanofillers in the recycled polymers such as PET, PP, HDPE, PVC, etc. and the attributed composites and blends is studied. The morphological, mechanical, rheological and thermal properties of prepared nanocomposites as well as the future challenges are extensively discussed. The present article determines the current status of nanotechnology in the polymer recycling which guide the future studies in this attractive field

Sample preparation method for ICP-MS measurement of 99Tc in a large amount of environmental samples

International Nuclear Information System (INIS)

Kondo, M.; Seki, R.

2002-01-01

Sample preparation for measurement of 99 Tc in a large amount of soil and water samples by ICP-MS has been developed using 95m Tc as a yield tracer. This method is based on the conventional method for a small amount of soil samples using incineration, acid digestion, extraction chromatography (TEVA resin) and ICP-MS measurement. Preliminary concentration of Tc has been introduced by co-precipitation with ferric oxide. The matrix materials in a large amount of samples were more sufficiently removed with keeping the high recovery of Tc than previous method. The recovery of Tc was 70-80% for 100 g soil samples and 60-70% for 500 g of soil and 500 L of water samples. The detection limit of this method was evaluated as 0.054 mBq/kg in 500 g soil and 0.032 μBq/L in 500 L water. The determined value of 99 Tc in the IAEA-375 (soil sample collected near the Chernobyl Nuclear Reactor) was 0.25 ± 0.02 Bq/kg. (author)

A Novel Experimental and Modelling Strategy for Nanoparticle Toxicity Testing Enabling the Use of Small Quantities

Directory of Open Access Journals (Sweden)

Marinda van Pomeren

2017-11-01

Full Text Available Metallic nanoparticles (NPs differ from other metal forms with respect to their large surface to volume ratio and subsequent inherent reactivity. Each new modification to a nanoparticle alters the surface to volume ratio, fate and subsequently the toxicity of the particle. Newly-engineered NPs are commonly available only in low quantities whereas, in general, rather large amounts are needed for fate characterizations and effect studies. This challenge is especially relevant for those NPs that have low inherent toxicity combined with low bioavailability. Therefore, within our study, we developed new testing strategies that enable working with low quantities of NPs. The experimental testing method was tailor-made for NPs, whereas we also developed translational models based on different dose-metrics allowing to determine dose-response predictions for NPs. Both the experimental method and the predictive models were verified on the basis of experimental effect data collected using zebrafish embryos exposed to metallic NPs in a range of different chemical compositions and shapes. It was found that the variance in the effect data in the dose-response predictions was best explained by the minimal diameter of the NPs, whereas the data confirmed that the predictive model is widely applicable to soluble metallic NPs. The experimental and model approach developed in our study support the development of (ecotoxicity assays tailored to nano-specific features.

Friendship quantity and quality as predictors of rejection sensitivity in adolescents

Directory of Open Access Journals (Sweden)

Gabriela Šeboková

2014-12-01

Full Text Available The current study examines friendship quality and quantity as unique predictors of rejection sensitivity in adolescents. The purpose of the study was to analyze whether the unique contributions of friendship quality and quantity differ in adolescent boys and girls. Rejection sensitivity is conceptualized as the disposition to anxiously expect, readily perceive and intensively react to social rejection. That is why rejection sensitivity is considered to be a cognitive-affective mechanism which leads to increase of internalizing problems in children and adolescents (loneliness, social anxiety, depression.... Friendship variables have been found to predict the level of internalizing problems in adolescents. Little to no research, however, has examined friendship quality and quantity as predictors of level of rejection sensitivity. Participants in this study were 184 students (98 girls and 86 boys, aged from 13 to 16 (M=13.83, SD=1. Adolescents completed measures assessing number of their friends, quality of best friendship (self-report questionnaire Friendship qualities scale, Bukowski, Hoza, Boivin, 1994 and rejection sensitivity (self-report questionnaire Rejection sensitivity scale, Downey, Feldman, 1996. Regression analysis indicated that friendship features (companionship, balance, help, security, closeness, friendship quantity and overall friendship quality are significant unique predictors of sensitivity rejection in adolescents with. Results suggest that adolescents with higher number of and higher quality friendships have lower concerns about the possibility and expectation of rejection, which can lead to minimizing the risk of development of internalizing problems. However, only a small proportion of variance was accounted for in rejection sensitivity by the friendship variables (small to medium effect size. This suggests that different kind of peer relationships (peer acceptance, popularity, peer victimization make unique, differential

Birthday Cake Activity Structured Arrangement for Helping Children Determining Quantities

Directory of Open Access Journals (Sweden)

Neni Mariana

2010-07-01

Full Text Available Few researches have been concerned about relation between children’s spatial thinking and number sense. Narrowing for this small research, we focused on one component of spatial thinking, that is structuring objects, and one component of number senses, that is cardinality by determining quantities. This study focused on a design research that was conducted in Indonesia in which we investigated pre-school children’s (between 2 and 3.5 years old ability in making structured arrangement and their ability to determine the quantities by looking at the arrangements. The result shows us that some of the children were able to make such arrangement. However, the children found difficulties either to determine quantities from those arrangements or to compare some structures to easily recognize number of objects.

Washington biofuel feedstock crop supply under output price and quantity uncertainty

International Nuclear Information System (INIS)

Zheng Qiujie; Shumway, C. Richard

2012-01-01

Subsidized development of an in-state biofuels industry has received some political support in the state of Washington, USA. Utilizing in-state feedstock supplies could be an efficient way to stimulate biofuel industries and the local economy. In this paper we estimate supply under output price and quantity uncertainty for major biofuel feedstock crops in Washington. Farmers are expected to be risk averse and maximize the utility of profit and uncertainty. We estimate very large Washington price elasticities for corn and sugar beets but a small price elasticity for a third potential feedstock, canola. Even with the large price elasticities for two potential feedstocks, their current and historical production levels in the state are so low that unrealistically large incentives would likely be needed to obtain sufficient feedstock supply for a Washington biofuel industry. Based on our examination of state and regional data, we find low likelihood that a Washington biofuels industry will develop in the near future primarily using within-state biofuel feedstock crops. - Highlights: ► Within-state feedstock crop supplies insufficient for Washington biofuel industry. ► Potential Washington corn and sugar beet supplies very responsive to price changes. ► Feedstock supplies more responsive to higher expected profit than lower risk. ► R and D for conversion of waste cellulosic feedstocks is potentially important policy.

Long-term integrated river basin planning and management of water quantity and water quality in mining impacted catchments

Science.gov (United States)

Pohle, Ina; Zimmermann, Kai; Claus, Thomas; Koch, Hagen; Gädeke, Anne; Uhlmann, Wilfried; Kaltofen, Michael; Müller, Fabian; Redetzky, Michael; Schramm, Martina; Schoenheinz, Dagmar; Grünewald, Uwe

2015-04-01

During the last decades, socioeconomic change in the catchment of the Spree River, a tributary of the Elbe, has been to a large extent associated with lignite mining activities and the rapid decrease of these activities in the 1990s. There are multiple interconnections between lignite mining and water management both in terms of water quantity and quality. During the active mining period a large-scale groundwater depression cone has been formed while river discharges have been artificially increased. Now, the decommissioned opencast mines are being transformed into Europe's largest man-made lake district. However, acid mine drainage causes low pH in post mining lakes and high concentrations of iron and sulphate in post mining lakes and the river system. Next to potential changes in mining activities, also the potential impacts of climate change (increasing temperature and decreasing precipitation) on water resources of the region are of major interest. The fundamental question is to what extent problems in terms of water quantity and water quality are exacerbated and whether they can be mitigated by adaptation measures. In consequence, long term water resource planning in the region has to formulate adaptation measures to climate change and socioeconomic change in terms of mining activities which consider both, water quantity and water quality aspects. To assess potential impacts of climate and socioeconomic change on water quantity and water quality of the Spree River catchment up to the Spremberg reservoir in the scenario period up to 2052, we used a model chain which consists of (i) the regional climate model STAR (scenarios with a further increase in temperature of 0 and 2 K), (ii) mining scenarios (mining discharges, cooling water consumption of thermal power plants), (iii) the ecohydrological model SWIM (natural water balance), (iv) the long term water management model WBalMo (managed discharges, withdrawal of water users, reservoir operation) and (v) the

[Relativity among starch quantity, polysaccharides content and total alkaloid content of Dendrobium loddigesii].

Science.gov (United States)

Zhu, Hua; Teng, Jianbei; Cai, Yi; Liang, Jie; Zhu, Yilin; Wei, Tao

2011-12-01

To find out the relativity among starch quantity, polysaccharides content and total alkaloid content of Dendrobium loddigesii. Microscopy-counting process was applied to starch quantity statistics, sulfuric acid-anthrone colorimetry was used to assay polysaccharides content and bromocresol green colorimetry was used to assay alkaloid content. Pearson product moment correlation analysis, Kendall's rank correlation analysis and Spearman's concordance coefficient analysis were applied to study their relativity. Extremely significant positive correlation was found between starch quantity and polysaccharides content, and significant negative correlation between alkaloid content and starch quantity was discovered, as well was between alkaloid content and polysaccharides content.

Non-Noether Conserved Quantity for Relativistic Nonholonomic System with Variable Mass

International Nuclear Information System (INIS)

Qiao Yongfen; Li Renjie; Ma Yongsheng

2005-01-01

Using form invariance under special infinitesimal transformations in which time is not variable, the non-Noether conserved quantity of the relativistic nonholonomic system with variable mass is studied. The differential equations of motion of the system are established. The definition and criterion of the form invariance of the system under infinitesimal transformations are studied. The necessary and sufficient condition under which the form invariance is a Lie symmetry is given. The condition under which the form invariance can be led to a non-Noether conserved quantity and the form of the conserved quantity are obtained. Finally, an example is given to illustrate the application of the result.

Exercise quantity-dependent muscle hypertrophy in adult zebrafish (Danio rerio).

Science.gov (United States)

Hasumura, Takahiro; Meguro, Shinichi

2016-07-01

Exercise is very important for maintaining and increasing skeletal muscle mass, and is particularly important to prevent and care for sarcopenia and muscle disuse atrophy. However, the dose-response relationship between exercise quantity, duration/day, and overall duration and muscle mass is poorly understood. Therefore, we investigated the effect of exercise duration on skeletal muscle to reveal the relationship between exercise quantity and muscle hypertrophy in zebrafish forced to exercise. Adult male zebrafish were exercised 6 h/day for 4 weeks, 6 h/day for 2 weeks, or 3 h/day for 2 weeks. Flow velocity was adjusted to maximum velocity during continual swimming (initial 43 cm/s). High-speed consecutive photographs revealed that zebrafish mainly drove the caudal part. Additionally, X-ray micro computed tomography measurements indicated muscle hypertrophy of the mid-caudal half compared with the mid-cranial half part. The cross-sectional analysis of the mid-caudal half muscle revealed that skeletal muscle (red, white, or total) mass increased with increasing exercise quantity, whereas that of white muscle and total muscle increased only under the maximum exercise load condition of 6 h/day for 4 weeks. Additionally, the muscle fiver size distributions of exercised fish were larger than those from non-exercised fish. We revealed that exercise quantity, duration/day, and overall duration were correlated with skeletal muscle hypertrophy. The forced exercise model enabled us to investigate the relationship between exercise quantity and skeletal muscle mass. These results open up the possibility for further investigations on the effects of exercise on skeletal muscle in adult zebrafish.

BIRTHDAY CAKE ACTIVITY STRUCTURED ARRANGEMENT FOR HELPING CHILDREN DETERMINING QUANTITIES

Directory of Open Access Journals (Sweden)

Neni Mariana

2010-07-01

Full Text Available Few researches have been concerned about relation between children’s spatialthinking and number sense. Narrowing for this small research, we focused onone component of spatial thinking, that is structuring objects, and onecomponent of number senses, that is cardinality by determining quantities. Thisstudy focused on a design research that was conducted in Indonesia in which weinvestigated pre-school children’s (between 2 and 3.5 years old ability inmaking structured arrangement and their ability to determine the quantities bylooking at the arrangements. The result shows us that some of the children wereable to make such arrangement. However, the children found difficulties eitherto determine quantities from those arrangements or to compare some structuresto easily recognize number of objects.Keywords: structures, structured arrangement, cardinality DOI: http://dx.doi.org/10.22342/jme.1.1.790.53-70

Complexity in an Unexpected Place: Quantities in Selected Acquisition Reports

Science.gov (United States)

2017-12-01

by the Army Acquisition Executive contains the following language . As a recently delegated Acquisition Category IC program, the AH-64E Apache...Complexity in an Unexpected Place: Quantities in Selected Acquisition Reports Gregory A. Davis, Project Leader Margaret L. Giles David M. Tate I...F E N S E A N A L Y S E S IDA Paper P-8490 Complexity in an Unexpected Place: Quantities in Selected Acquisition Reports Gregory A. Davis

Method for the preparation of a light and insulating concrete, and concrete thus prepared. Procede pour la preparation d'un beton leger et isolant, et le beton obtenu

Energy Technology Data Exchange (ETDEWEB)

Guindon, B

1991-04-30

A process is provided for the preparation of a light insulating concrete whose density after setting is on the order of 400-1,000 kg/m{sup 3}. All the following steps used in the method, except for forming and setting, are carried out inside a conventional concrete mixer. According to a first version of the invention, an anti-shrinking agent constituted by fibers is introduced into a sufficient quantity of mix water for enough time to disperse and mix all the fibers. Into the mixture thus obtained is introduced a mixture consisting of ca 20-50 vol % of a dry hydraulic binder and ca 50-80 vol % of dry polystyrene aggregates. The quantity of hydraulic binder is adjusted such that the mix water is at least in sufficient quantity to allow a complete setting of the binder. The whole mixture is mixed for enough time to disperse and wet all the hydraulic binder and achieve a uniform distribution of fibers, aggregates, and binder in the mix water. The resulting concrete mix is then formed and left to set. The anti-shrink agent advantageously consists of polypropylene fibers and the polystyrene aggregates are expanded polystyrene spheres of 1-7 mm diameter. The invention provides a concrete that can be formed, worked, nailed, and/or screwed like wood, thereby simplifying construction of concrete structures. If used for foundation walls, the insulation of basements is improved and no additional interior insulation is necessary. Experiments are described to illustrate the invention.

Symmetries and conserved quantities in geodesic motion

International Nuclear Information System (INIS)

Hojman, S.; Nunez, L.; Patino, A.; Rago, H.

1986-01-01

Recently obtained results linking several constants of motion to one (non-Noetherian) symmetry to the problem of geodesic motion in Riemannian space-times are applied. The construction of conserved quantities in geodesic motion as well as the deduction of geometrical statements about Riemannian space-times are achieved

Similarities between 2D and 3D convection for large Prandtl number

Indian Academy of Sciences (India)

2016-06-18

RBC), we perform a compara- tive study of the spectra and fluxes of energy and entropy, and the scaling of large-scale quantities for large and infinite Prandtl numbers in two (2D) and three (3D) dimensions. We observe close ...

ADM pseudotensors, conserved quantities and covariant conservation laws in general relativity

International Nuclear Information System (INIS)

Fatibene, L.; Ferraris, M.; Francaviglia, M.; Lusanna, L.

2012-01-01

The ADM formalism is reviewed and techniques for decomposing generic components of metric, connection and curvature are obtained. These techniques will turn out to be enough to decompose not only Einstein equations but also covariant conservation laws. Then a number of independent sets of hypotheses that are sufficient (though not necessary) to obtain standard ADM quantities (and Hamiltonian) from covariant conservation laws are considered. This determines explicitly the range in which standard techniques are equivalent to covariant conserved quantities. The Schwarzschild metric in different coordinates is then considered, showing how the standard ADM quantities fail dramatically in non-Cartesian coordinates or even worse when asymptotically flatness is not manifest; while, in view of their covariance, covariant conservation laws give the correct result in all cases. - Highlights: ► In the paper ADM conserved quantities for GR are obtained from augmented conservation laws. ► Boundary conditions for this to be possible are considered and compared with the literature. ► Some different forms of Schwarzschild solutions are considered as simple examples of different boundary conditions.

Studies on quantity and composition of dairy cow excreta

International Nuclear Information System (INIS)

Peschke, H.

1982-01-01

After feeding a lactating dairy cow a day ration completely enriched with 15 N, the quantities of feces and urine were registered over a period of ten days and put into proportion to the animal mass. The fecal dry matter was put into proportion to the dry matter of the fodder by means of 15 N analysis the N excretion with the excreta was determined concerning quantity and time. Selected feces and urine charges were used to produce a slurry model. The content of nutritive elements of the initial components and of the organic fertilizer are discussed. (author)

Validity of the concept of absorbed dose as a physical quantity

International Nuclear Information System (INIS)

Tada, Jun-Ichiro; Katoh, Kazuaki.

1995-01-01

The concept of the 'absorbed dose' of ionizing radiation is scrutinized from physical point of view. It is shown that the concept and definition of the quantity in the ICRU system is disqualified as a physical quantity and the absorbed dose can not always be a 'measure of cause' in describing causality relation between radiation and effects on matter. The current absorbed dose depends even on the energy that have already been brought out from the matter, contrary to the intention of introducing the quantity. Trials to remove these difficulties are made. However, it is also shown there still exists an essential problem that cannot be solved by improving the formulation. (author)

Dangerous quantities of radioactive material (D-values). Emergency preparedness and response. Publication date: August 2006

International Nuclear Information System (INIS)

2006-08-01

Radioactive material is widely used in industry, medicine, education and agriculture. In addition, it occurs naturally. The health risk posed by these materials vary widely depending on many factors, the most important of which are the amount of the material involved and its physical and chemical form. Therefore, there is a need to identify the quantity and type of radioactive material for which emergency preparedness and other arrangements (e.g. security) are warrant due to the health risk they pose. The aim of this publication is to provide practical guidance for Member States on that quantity of radioactive material that may be considered dangerous. A dangerous quantity is that, which if uncontrolled, could be involved in a reasonable scenario resulting in the death of an exposed individual or a permanent injury, which decreases that person's quality of life. This publication is published as part of the IAEA Emergency Preparedness and Response Series. It supports several publications including: the IAEA Safety Requirements 'Preparedness and Response for a Nuclear or Radiological Emergency', IAEA Safety Standards Series No. GS-R-2. IAEA, Vienna (2002); IAEA Safety Guide 'Categorization of Radioactive Sources', IAEA Safety Standards Series No RS-G-1.9, IAEA, Vienna (2005) and IAEA Safety Guide 'Arrangements for Preparedness for a Nuclear or Radiological Emergency' IAEA Safety Standards Series No. GS-G-2.1, IAEA, Vienna (2006). The procedures and data in this publication have been prepared with due attention to accuracy. However, as part of the review process, they undergo ongoing quality assurance checks. Comments are welcome and, following a period that will allow for a more extensive review, the IAEA may revise this publication as part of the process of continuous improvement. The publication uses a number of exposure scenarios, risk models and dosimetric data, which could be used during the response to nuclear or radiological emergency or other purposes

Preparation and characterization of oil palm frond based cellulose hydrogel and its swelling properties

Science.gov (United States)

Selvakumaran, Nesha; Lazim, Mohd Azwani Shah bin Mat

2016-11-01

Malaysia is one of the largest producer of palm oil thus the quantity of biomass each year from this industry is very large. The oil palm frond from palm oil industry can be used as a source of cellulose which can be incorporated into hydrogel to be used as adsorbent. This research reported how to disperse 2 % cellulose in a `green-solution' prepared by using urea and sodium hydroxide. Polymerization is carried out between the monomers polyacrylamide and cellulose using microwave to form hydrogel. Hydrogel with 2 % cellulose have a swelling index of 1814 %. Meanwhile, zero hydrogel which is made with only polyacrylamide has swelling index of 15 %. Scanning electron microscope shows that cellulose hydrogel have a rough surface compared with zero hydrogel. This might attribute to the high swelling index for cellulose hydrogel compared with zero hydrogel. Meanwhile, FTIR shows that successful polymerization has occurred between polyacrylamide and cellulose with the characteristic band at 1657.99 cm-1 which is for N-H bond.

16 CFR 500.7 - Net quantity of contents, method of expression.

Science.gov (United States)

2010-01-01

... expression. The net quantity of contents shall be expressed in terms of weight or mass, measure, numerical... consumers. The net quantity of contents statement shall be in terms of fluid measure if the commodity is liquid, or in terms of weight or mass if the commodity is solid, semi-solid, or viscous, or a mixture of...

Uncertainty analysis of thermal quantities measurement in a centrifugal compressor

Science.gov (United States)

Hurda, Lukáš; Matas, Richard

2017-09-01

Compressor performance characteristics evaluation process based on the measurement of pressure, temperature and other quantities is examined to find uncertainties for directly measured and derived quantities. CFD is used as a tool to quantify the influences of different sources of uncertainty of measurements for single- and multi-thermocouple total temperature probes. The heat conduction through the body of the thermocouple probe and the heat-up of the air in the intake piping are the main phenomena of interest.

Measuring nanocurie quantities of tritium bred in metallic lithium and lithium oxide samples

International Nuclear Information System (INIS)

Bertone, P.C.

1985-01-01

The LBM program requires that nanocurie quantities of tritium, bred in both lithium oxide pellets and lithium samples, be measured with an uncertainty not exceeding + or - 6%. Two methods of accurately measuring nanocurie quantities of tritium bred in LBM lithium oxide pellets and one method of accurately measuring nanocurie quantities of tritium bred in lithium samples are described. Potential errors associated with these tritium measurement techniques are also discussed

Primary factors affecting water quality and quantity in four watersheds in Eastern Puerto Rico

Science.gov (United States)

Murphy, Sheila F.; Stallard, Robert F.

2009-01-01

As part of the U.S. Geological Survey (USGS) Water, Energy, and Biogeochemical Budgets (WEBB) program, four small watersheds in eastern Puerto Rico were monitored to identify and evaluate the effects of geology, landcover, atmospheric deposition, and other factors on stream water quality and quantity. Two catchments are located on coarse-grained granitic plutonic rocks, which weather to quartz- and clay-rich, sandy soils, and two are located on fine-grained volcanic rocks and volcaniclastic sediments, which weather to quartz-poor, fine-grained soils. These differing soil materials result in different hydrologic regimes. Soils on the granitic rocks have greater permeability than those developed on the volcaniclastic rocks, allowing more water infiltration and potentially greater landslide erosion rates. For each bedrock type, one catchment was covered with mature rainforest, and the other catchment was affected by agricultural practices typical of eastern Puerto Rico. These practices led to the erosion of much of the original surface soil in the agricultural watersheds, which introduced large quantities of sediment to stream channels. The agricultural watersheds are undergoing natural reforestation, like much of Puerto Rico. Eastern Puerto Rico receives large atmospheric inputs of marine salts, pollutants from the Northern Hemisphere, and Saharan Desert dust. Marine salts contribute over 80 percent of the ionic charge in precipitation, with peak inputs in January. Intense storms, mostly hurricanes, are associated with exceptionally high chloride concentrations in stream waters. Temperate pollution contributes nitrate, ammonia, and sulfate, with maximum inputs during northern cold fronts in January, April, and May. Pollution inputs have increased through time. Desert dust peaks in June and July, during times of maximum dust transport from the Saharan Desert across the Atlantic Ocean.

Development of ion beam sputtering techniques for actinide target preparation

International Nuclear Information System (INIS)

Aaron, W.S.; Zevenbergen, L.A.; Adair, H.L.

1985-01-01

Ion beam sputtering is a routine method for the preparation of thin films used as targets because it allows the use of minimum quantity of starting material, and losses are much lower than most other vacuum deposition techniques. Work is underway in the Isotope Research Materials Laboratory (IRML) at ORNL to develop the techniques that will make the preparation of actinide targets up to 100 μg/cm 2 by ion beam sputtering a routinely available service from IRML. The preparation of the actinide material in a form suitable for sputtering is a key to this technique, as is designing a sputtering system that allows the flexibility required for custom-ordered target production. At present, development work is being conducted on low-activity in a bench-top system. The system will then be installed in a hood or glove box approved for radioactive materials handling where processing of radium, actinium, and plutonium isotopes among others will be performed. (orig.)

Development of ion beam sputtering techniques for actinide target preparation

Science.gov (United States)

Aaron, W. S.; Zevenbergen, L. A.; Adair, H. L.

1985-06-01

Ion beam sputtering is a routine method for the preparation of thin films used as targets because it allows the use of a minimum quantity of starting material, and losses are much lower than most other vacuum deposition techniques. Work is underway in the Isotope Research Materials Laboratory (IRML) at ORNL to develop the techniques that will make the preparation of actinide targets up to 100 μg/cm 2 by ion beam sputtering a routinely available service from IRML. The preparation of the actinide material in a form suitable for sputtering is a key to this technique, as is designing a sputtering system that allows the flexibility required for custom-ordered target production. At present, development work is being conducted on low-activity actinides in a bench-top system. The system will then be installed in a hood or glove box approved for radioactive materials handling where processing of radium, actinium, and plutonium isotopes among others will be performed.

Preparation and quantification of 3'-phosphoadenosine 5'-phospho[35S]sulfate with high specific activity

International Nuclear Information System (INIS)

Vargas, F.

1988-01-01

The synthesis and quantitation of the sulfate donor 3'-phosphoadenosine 5'-phospho[35S]sulfate (PAP35S), prepared from inorganic [35S]sulfate and ATP, were studied. An enzymatic transfer method based upon the quantitative transfer of [35S]sulfate from PAP35S to 2-naphthol and 4-methylumbelliferone by the action of phenolsulfotransferase activity from rat brain cytosol was also developed. The 2-naphthyl[35S]sulfate or 35S-methylumbelliferone sulfate formed was isolated by polystyrene bead chromatography. This method allows the detection of between 0.1 pmol and 1 nmol/ml of PAP35S. PAP35S of high specific activity (75 Ci/mmol) was prepared by incubating ATP and carrier-free Na2 35SO4 with a 100,000g supernatant fraction from rat spleen. The product was purified by ion-exchange chromatography. The specific activity and purity of PAP35S were estimated by examining the ratios of Km values for PAP35S of the tyrosyl protein sulfotransferase present in microsomes from rat cerebral cortex. The advantage and applications of these methods for the detection of femtomole amounts, and the synthesis of large scale quantities of PAP35S with high specific activity are discussed

Food quantity affects the sensitivity of Daphnia to road salt.

Science.gov (United States)

Brown, Arran H; Yan, Norman D

2015-04-07

Road deicing operations have raised chloride (Cl) levels in many temperate lakes in Europe and North America. These lakes vary widely in trophic status, but to date, no one has quantified the interaction between food quantity and road salt toxicity. We examined the effects of food quantity (particulate algal C concentration (C)) on the chronic toxicity of Cl to Daphnia in soft-water bioassays. There was a strong positive linear relationship (r(2) = 0.92 for NaCl and r(2) = 0.96 for CaCl2) between food quantity and Cl LC50. As food quantity increased from 0.2 to 1.0 mg C/L (levels characteristic of oligotrophic to eutrophic lakes, respectively), the chronic Cl LC50 increased from 55.7 to 284.8 mg Cl/L. Salt type (NaCl or CaCl2) did not affect the Cl LC50, Daphnia life history parameters, or the intrinsic rate of population increase (r). The life history parameter most sensitive to Cl was neonate production. Cl did not inhibit egg production, nor was the maternal lipid investment in eggs changed, but egg viability and the subsequent release of live neonates decreased as Cl levels increased and food decreased. Our results suggest the trophic status of lakes should be considered when assessing ecological threat from Cl.

Validation of uncertainty of weighing in the preparation of radionuclide standards by Monte Carlo Method

International Nuclear Information System (INIS)

Cacais, F.L.; Delgado, J.U.; Loayza, V.M.

2016-01-01

In preparing solutions for the production of radionuclide metrology standards is necessary measuring the quantity Activity by mass. The gravimetric method by elimination is applied to perform weighing with smaller uncertainties. At this work is carried out the validation, by the Monte Carlo method, of the uncertainty calculation approach implemented by Lourenco and Bobin according to ISO GUM for the method by elimination. The results obtained by both uncertainty calculation methods were consistent indicating that were fulfilled the conditions for the application of ISO GUM in the preparation of radioactive standards. (author)

Thermodynamic quantities for the Klein–Gordon equation

Indian Academy of Sciences (India)

We study some thermodynamic quantities for the Klein–Gordon equation with a linear plus inverselinear, scalar potential. We obtain the energy eigenvalues with the help of the quantization rule from the biconfluent Heun's equation.We use a method based on the Euler–MacLaurin formula to analytically compute thethermal ...

19 CFR 351.409 - Differences in quantities.

Science.gov (United States)

2010-04-01

... DUTIES Calculation of Export Price, Constructed Export Price, Fair Value, and Normal Value § 351.409... comparing export price or constructed export price with normal value, the Secretary will make a reasonable... section 773(a)(6)(C)(i) of the Act.) (b) Sales with quantity discounts in calculating normal value. The...

16 CFR 1.23 - Quantity limit rules.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Quantity limit rules. 1.23 Section 1.23 Commercial Practices FEDERAL TRADE COMMISSION ORGANIZATION, PROCEDURES AND RULES OF PRACTICE GENERAL... Robinson-Patman Act. These rules have the force and effect of law. [32 FR 8444, June 13, 1967. Redesignated...

7 CFR 1427.170 - Quantity for loan.

Science.gov (United States)

2010-01-01

... to the preservation or safety of the loan collateral. Loans may be made on a lower percentage basis... 7 Agriculture 10 2010-01-01 2010-01-01 false Quantity for loan. 1427.170 Section 1427.170... OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS COTTON Recourse Seed Cotton Loans § 1427.170...

Large Scale Visual Recommendations From Street Fashion Images

OpenAIRE

Jagadeesh, Vignesh; Piramuthu, Robinson; Bhardwaj, Anurag; Di, Wei; Sundaresan, Neel

2014-01-01

We describe a completely automated large scale visual recommendation system for fashion. Our focus is to efficiently harness the availability of large quantities of online fashion images and their rich meta-data. Specifically, we propose four data driven models in the form of Complementary Nearest Neighbor Consensus, Gaussian Mixture Models, Texture Agnostic Retrieval and Markov Chain LDA for solving this problem. We analyze relative merits and pitfalls of these algorithms through extensive e...

Radioenzymatic microassay for picogram quantities of serotonin or acetylserotonin in biological fluids and tissues

International Nuclear Information System (INIS)

Hussain, M.N.; Benedict, C.R.

1987-01-01

This paper describes several modifications of the original radioenzymatic assay for serotonin which increase the sensitivity of the assay 20-fold as well as enhance its reliability. Using this method serotonin concentrations can be directly measured in biological examples without precleaning the sample. When compared to currently available methods this assay is specific and sensitive to approximately 1 pg of serotonin and can be used to measure serotonin levels in individual brain nuclei or microliter quantities of biological fluids. This assay can be easily adapted for the direct measurement of N-acetylserotonin. A large number of samples can be assayed in a single working day

Urgency of increasing the quantity and quality of student creativity program

Science.gov (United States)

Sarmini; Prasetya, Ketut; Nadiroh, Ulin

2018-01-01

Student creativity is very important to improve the quality and quantity. The purpose of this paper is to identify the quality and quantity of the Student Creativity Program. The method in this research is exploratory study. The subjects taken are the leaders of deans and vice deans at the State University of Surabaya. Data collection techniques used are kusioner. The result of this research is creativity program in student is very important. Not only improve the quality and quantity of creativity, but also affect the image of the institution. It is necessary to have written rules on the regulations on the Student Creativity Program and to take a comprehensive and comprehensive approach, and to organize the budget is the main thing.

Uncertainties of exposure-related quantities in mammographic x-ray unit quality control

International Nuclear Information System (INIS)

Gregory, Kent J.; Pattison, John E.; Bibbo, Giovanni

2006-01-01

Breast screening programs operate in many countries with mammographic x-ray units subject to stringent quality control tests. These tests include the evaluation of quantities based on exposure measurements, such as half value layer, automatic exposure control reproducibility, average glandular dose, and radiation output rate. There are numerous error sources that contribute to the uncertainty of these exposure-related quantities, some of which are unique to the low energy x-ray spectrum produced by mammographic x-ray units. For each of these exposure-related quantities, the applicable error sources and their magnitudes vary, depending on the test equipment used to make the measurement, and whether or not relevant corrections have been applied. This study has identified and quantified a range of error sources that may be used to estimate the combined uncertainty of these exposure-related quantities, given the test equipment used and corrections applied. The uncertainty analysis uses methods described by the International Standards Organization's Guide to the Expression of Uncertainty in Measurement. Examples of how these error sources combine to give the uncertainty of the exposure-related quantities are presented. Using the best test equipment evaluated in this study, uncertainties of the four exposure-related quantities at the 95% confidence interval were found to be ±1.6% (half value layer), ±0.0008 (automatic exposure control reproducibility), ±2.3% (average glandular dose), and ±2.1% (radiation output rate). In some cases, using less precise test equipment or failing to apply corrections, resulted in uncertainties more than double in magnitude

Radiation Dose for Self-Disposal due to the Quantity of Radioactive Waste

Energy Technology Data Exchange (ETDEWEB)

Koo, Daeseo; Sung, Hyun-Hee; Kim, Seung-Soo; Kim, Gye-Nam; Choi, Jong-Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

In this study, we evaluated resident radiation dose due to cover depth on contaminated zone such as uranium contaminated soil and concrete wastes under radiation dose limit using RESRAD Version 7.0. The uranium concentration of contaminated zone due to the cover depth are also analyzed. Possibility for self-disposal of uranium contaminated soil and concrete wastes is evaluated from these calculating data. There are several radioactive material disposal methods such as regulation exemption, decontamination and long term storage. To acquire radiation dose under self-disposal from them, the study on decontamination of some uranium contaminated soil and concrete wastes was performed using electrokinectic-electrodialytic. We evaluated radiation dose due to cover depth on contaminated zone such as uranium contaminated soil and concrete wastes under radiation dose limit using RESRAD Version 7.0. As cover depth increases, the tolerable uranium concentration increases up to cover depth (1.5 m) and then it showed saturated uranium concentration above cover depth (1.5 m). Therefore, to carry out self-disposal on the quantity (1000 drums≒300,000 kg) of radioactive waste is easier than to carry out on the quantity (2000 drums≒600,000 kg) of radioactive waste owing to the large tolerable uranium concentration for self-disposal of radioactive waste. As cover depth increases, the individual radiation dose rate decreased up to cover depth (1.5 m) and then it showed saturated individual radiation dose rate above cover depth (1.5 m)

Radiation Dose for Self-Disposal due to the Quantity of Radioactive Waste

International Nuclear Information System (INIS)

Koo, Daeseo; Sung, Hyun-Hee; Kim, Seung-Soo; Kim, Gye-Nam; Choi, Jong-Won

2016-01-01

In this study, we evaluated resident radiation dose due to cover depth on contaminated zone such as uranium contaminated soil and concrete wastes under radiation dose limit using RESRAD Version 7.0. The uranium concentration of contaminated zone due to the cover depth are also analyzed. Possibility for self-disposal of uranium contaminated soil and concrete wastes is evaluated from these calculating data. There are several radioactive material disposal methods such as regulation exemption, decontamination and long term storage. To acquire radiation dose under self-disposal from them, the study on decontamination of some uranium contaminated soil and concrete wastes was performed using electrokinectic-electrodialytic. We evaluated radiation dose due to cover depth on contaminated zone such as uranium contaminated soil and concrete wastes under radiation dose limit using RESRAD Version 7.0. As cover depth increases, the tolerable uranium concentration increases up to cover depth (1.5 m) and then it showed saturated uranium concentration above cover depth (1.5 m). Therefore, to carry out self-disposal on the quantity (1000 drums≒300,000 kg) of radioactive waste is easier than to carry out on the quantity (2000 drums≒600,000 kg) of radioactive waste owing to the large tolerable uranium concentration for self-disposal of radioactive waste. As cover depth increases, the individual radiation dose rate decreased up to cover depth (1.5 m) and then it showed saturated individual radiation dose rate above cover depth (1.5 m)

Preparation and evaluation of some investigated natural and acrylonitrile rubber vulcanizations for physiotherapeutic purposes

International Nuclear Information System (INIS)

Helaly, F.M; El-Sawy, S.M.

2005-01-01

A trial was made to design and prepare rubber article that can be used to reactivate, strengthen and reinforce the hand muscles and fingers which had suffered from trouble movement.The investigated rubber article was prepared from natural and acrylonitrile rubber formulations. These formulations were processed in the form of compounds which contain significant quantities of fillers as Hisil, CaCO 3 and TiO 2 .The rheological characteristics and physicochemical properties of the vulcanizations were determined according to standard tests. It was found that it is possible to prepare the designated rubber article for the desired purpose. The test results show that the prepared rubber article has a good chemical resistant against acid, alkali, and salt. Also it possesses high resistance to deterioration and deformation. The prepared article has an ability to retain its elastic property after the action of compressive forces at 70 degree C for 24 hours.This was conformed with applied commercial hand exercise therapeutic article

Creating Large Scale Database Servers

International Nuclear Information System (INIS)

Becla, Jacek

2001-01-01

The BaBar experiment at the Stanford Linear Accelerator Center (SLAC) is designed to perform a high precision investigation of the decays of the B-meson produced from electron-positron interactions. The experiment, started in May 1999, will generate approximately 300TB/year of data for 10 years. All of the data will reside in Objectivity databases accessible via the Advanced Multi-threaded Server (AMS). To date, over 70TB of data have been placed in Objectivity/DB, making it one of the largest databases in the world. Providing access to such a large quantity of data through a database server is a daunting task. A full-scale testbed environment had to be developed to tune various software parameters and a fundamental change had to occur in the AMS architecture to allow it to scale past several hundred terabytes of data. Additionally, several protocol extensions had to be implemented to provide practical access to large quantities of data. This paper will describe the design of the database and the changes that we needed to make in the AMS for scalability reasons and how the lessons we learned would be applicable to virtually any kind of database server seeking to operate in the Petabyte region

Creating Large Scale Database Servers

Energy Technology Data Exchange (ETDEWEB)

Becla, Jacek

2001-12-14

The BaBar experiment at the Stanford Linear Accelerator Center (SLAC) is designed to perform a high precision investigation of the decays of the B-meson produced from electron-positron interactions. The experiment, started in May 1999, will generate approximately 300TB/year of data for 10 years. All of the data will reside in Objectivity databases accessible via the Advanced Multi-threaded Server (AMS). To date, over 70TB of data have been placed in Objectivity/DB, making it one of the largest databases in the world. Providing access to such a large quantity of data through a database server is a daunting task. A full-scale testbed environment had to be developed to tune various software parameters and a fundamental change had to occur in the AMS architecture to allow it to scale past several hundred terabytes of data. Additionally, several protocol extensions had to be implemented to provide practical access to large quantities of data. This paper will describe the design of the database and the changes that we needed to make in the AMS for scalability reasons and how the lessons we learned would be applicable to virtually any kind of database server seeking to operate in the Petabyte region.

A fast method for large-scale isolation of phages from hospital ...

African Journals Online (AJOL)

This plaque-forming method could be adopted to isolate E. coli phage easily, rapidly and in large quantities. Among the 18 isolated E. coli phages, 10 of them had a broad host range in E. coli and warrant further study. Key words: Escherichia coli phages, large-scale isolation, drug resistance, biological properties.

Stormwater management impacts on urban stream water quality and quantity during and after development in Clarksburg, MD

Science.gov (United States)

Loperfido, J. V.; Noe, G. B.; Jarnagin, S.; Mohamoud, Y. M.; Van Ness, K.; Hogan, D. M.

2012-12-01

Urbanization and urban land use leads to degradation of local stream habitat and 'urban stream syndrome.' Best Management Practices (BMPs) are often used in an attempt to mitigate the impact of urban land use on stream water quality and quantity. Traditional development has employed stormwater BMPs that were placed in a centralized manner located either in the stream channel or near the riparian zone to treat stormwater runoff from large drainage areas; however, urban streams have largely remained impaired. Recently, distributed placement of BMPs throughout the landscape has been implemented in an attempt to detain, treat, and infiltrate stormwater runoff from smaller drainage areas near its source. Despite increasing implementation of distributed BMPs, little has been reported on the catchment-scale (1-10 km^2) performance of distributed BMPs and how they compare to centralized BMPs. The Clarksburg Special Protection Area (CSPA), located in the Washington, DC exurbs within the larger Chesapeake Bay watershed, is undergoing rapid urbanization and employs distributed BMPs on the landscape that treat small drainage areas with the goal of preserving high-quality stream resources in the area. In addition, the presence of a nearby traditionally developed (centralized BMPs) catchment and an undeveloped forested catchment makes the CSPA an ideal setting to understand how the best available stormwater management technology implemented during and after development affects stream water quality and quantity through a comparative watershed analysis. The Clarksburg Integrated Monitoring Partnership is a consortium of local and federal agencies and universities that conducts research in the CSPA including: monitoring of stream water quality, geomorphology, and biology; analysis of stream hydrological and water quality data; and GIS mapping and analysis of land cover, elevation change and BMP implementation data. Here, the impacts of urbanization on stream water quantity

Principles and foundation: national standards on quantities and units in nuclear science field

International Nuclear Information System (INIS)

Chen Lishu

1993-11-01

The main contents of National Standards on Quantities and units of atomic and nuclear physics (GB 3102.9) and Quantities and Units of nuclear reactions and ionizing radiations (GB 310.10) are presented in which most important quantities with their symbols and definitions in the nuclear scientific field are given. The principles and foundation, including the International System of Units (SI) and its application to the nuclear scientific field, in the setting of the National Standards are explained

Preparation and Property Recognition of Nimodipine Molecularly Imprinted Polymer

Directory of Open Access Journals (Sweden)

Fei-fei CHEN

2015-09-01

Full Text Available Objective: To explore the application of molecular imprinting technique in the separation and detection of nimodipine. Methods: Methacrylic acid as functional monomer, pentaerythritol triacrylate as cross-linking agent were used to prepare molecularly imprinted polymer (MIP with the feature of specific recognition performance on imprinting molecule nimodipine under condition of template molecule nimodipine. The preparation conditions, recognition performance of MIP on nimodipine, different proportions of template molecule and functional monomer, the selectivity to other substrate, and the relationship between adsorption quantity (Q and time were observed. Results: MIP was prepared successfully bynimodipine as template and pentaerythritol triacrylate as cross-linking agent, with the feature of specific recognition performance on nimodipine. The static adsorption distribution coefficient (KD was 0.2264. The equation of Q and the concentration of substrate of template MIP was y = -0.21x+0.2204. Combining capacity of template molecule at the same concentration enhanced with the increasing proportion of functional monomer.Conclusion: Nimodipine MIP based on molecular imprinting technique may become a new approach to chiral separation for nimodipine.

Remotely controlled large container disposal methodology

International Nuclear Information System (INIS)

Amir, S.J.

1994-09-01

Remotely Handled Large Containers (RHLC), also called drag-off boxes, have been used at the Hanford Site since the 1940s to dispose of large pieces of radioactively contaminated equipment. These containers are typically large steel-reinforced concrete boxes, which weigh as much as 40 tons. Because large quantities of high-dose waste can produce radiation levels as high as 200 mrem/hour at 200 ft, the containers are remotely handled (either lifted off the railcar by crane or dragged off with a cable). Many of the existing containers do not meet existing structural and safety design criteria and some of the transportation requirements. The drag-off method of pulling the box off the railcar using a cable and a tractor is also not considered a safe operation, especially in view of past mishaps

Compound antimalarial ethosomal cataplasm: preparation, evaluation, and mechanism of penetration enhancement.

Science.gov (United States)

Shen, Shuo; Liu, Shu-Zhi; Zhang, Yu-Shi; Du, Mao-Bo; Liang, Ai-Hua; Song, Li-Hua; Ye, Zu-Guang

2015-01-01

Malaria is still a serious public health problem in some parts of the world. The problems of recurrence and drug resistance are increasingly more serious. Thus, it is necessary to develop a novel antimalarial agent. The objectives of this study were to construct a novel compound antimalarial transdermal nanosystem-ethosomal cataplasm, to investigate its characteristics and efficiency, and to systematically explore the penetration-enhancing mechanisms of ethosomal cataplasm. Artesunate-loaded ethosomes and febrifugine-loaded ethosomes were prepared, and their characteristics were evaluated. Drug-loaded ethosomes were incorporated in the matrix of cataplasm to form the compound antimalarial ethosomal cataplasm. With the help of ethosomal technology, the accumulated permeation quantity of artesunate significantly increased at 8 hours after administration, which was 1.57 times as much as that of conventional cataplasm. Soon after administration, the ethosomal cataplasm could make a large quantity of antimalarial drug quickly penetrate through skin, then the remaining drug in the ethosomal cataplasm could be steadily released. These characteristics of ethosomal cataplasm are favorable for antimalarial drugs to kill Plasmodium spp. quickly and prevent the resurgence of Plasmodium spp. As expected, the ethosomal cataplasm showed good antimalarial efficiency in this experiment. The negative conversion rates were 100% and the recurrence rates were 0% at all dosages. The mechanism of penetration enhancement of the ethosomal cataplasm was systematically explored using an optics microscope, polarization microscope, and transmission electron microscopy. The microstructure, ultrastructure, and birefringent structure in skin were observed. Data obtained in this study showed that the application of ethosomal technology to antimalarial cataplasm could improve the transdermal delivery of drug, enhance the efficacy, and facilitate practical application in clinic.

Conserved quantities for stationary Einstein-Maxwell space-times

International Nuclear Information System (INIS)

Esposito, F.P.; Witten, L.

1978-01-01

It is shown that every stationary Einstein-Maxwell space-time has eight divergence-free vector fields and these are isolated in general form. The vector fields and associated conserved quantities are calculated for several families of space-times. (Auth.)

Quantity judgments in the context of risk/reward decision making in striped field mice: first “count,” then hunt

Science.gov (United States)

Panteleeva, Sofia; Reznikova, Zhanna; Vygonyailova, Olga

2013-01-01

We simulated the situation of risky hunting in the striped field mouse Apodemus agrarius in order to examine whether these animals are able to make a choice between small and large quantities of live prey (ants). In the first (preliminary) experiment we investigated to what extent mice were interested in ants as a live prey and how their hunting activity depended on the quantity of these edible but rather aggressive insects. We placed mice one by one into arenas together with ant groups of different quantities, from 10 to 60. Surprisingly, animals, both wild-caught and laboratory-reared, displayed rather skilled predatory attacks: mice killed and ate from 0.37 ± 003 to 4 ± 0.5 ants per minute. However, there was a threshold number of ants in the arenas when rodents expressed signs of discomfort and started to panic, likely because ants bit them. This threshold corresponds to the dynamic density (about 400 individuals per m2 per min) in the vicinity of anthills and ants' routes in natural environment. In the second experiment mice had to choose between different quantities of ants placed in two transparent tunnels. Ants here served both as food items and as a source of danger. As far as we know, this is the first experimental paradigm based on evaluation of quantity judgments in the context of risk/reward decision making where the animals face a trade-off between the hedonistic value of the prey and the danger it presents. We found that when mice have to choose between 5 vs. 15, 5 vs. 30, and 10 vs. 30 ants, they always tend to prefer the smaller quantity, thus displaying the capacity for distinguishing more from less in order to ensure comfortable hunting. The results of this study are ecologically relevant as they reflect situations and challenges faced by free-living small rodents. PMID:23407476

Quantity judgements in the context of risk/reward decision making in striped field mice: First count, then hunt

Directory of Open Access Journals (Sweden)

Sofia ePanteleeva

2013-02-01

Full Text Available We simulated the vital situation of risky hunting in the striped field mouse Apodemus agrarius in order to examine whether these animals are able to make a choice between small and large quantities of live prey (ants. In the first (preliminary experiment we investigated to what extent mice were interested in ants as a live prey and how their hunting activity depended on the quantity of these edible but rather aggressive insects. We placed mice one by one into arenas together with ant groups of different size, from 10 to 60. Surprisingly, animals, both wild-caught and laboratory-reared, displayed rather skilled predatory attacks: mice killed and ate from 0.37±003 to 4±0.5 ants per minute. However, there was a threshold number of ants in the arenas when rodents expressed signs of discomfort and started to panic, because ants bit them. This threshold corresponds to the dynamic density (about 400 individuals per m 2per min in the vicinity of anthills and ants’ routes in natural environment. In the second experiment mice had to choose between different quantities of ants placed in two transparent tunnels. Ants here served both as food items and as a source of danger. As far as we know, this is the first experimental paradigm based on evaluation of quantity judgements in the context of risk/reward decision making where the animals face a trade-off between the hedonistic value of the prey and the danger it presents.. We found that when mice have to choose between 5 vs 15, 5 vs 30 and 10 vs 30 ants, they always tend to prefer the smaller quantity, thus displaying the capacity for distinguishing more from less in order to ensure comfortable hunting. The results of this study are ecologically relevant as they reflect situations and challenges faced by free-living small rodents.

Bowel preparation for CT colonography

International Nuclear Information System (INIS)

Neri, Emanuele; Lefere, Philippe; Gryspeerdt, Stefaan; Bemi, Pietro; Mantarro, Annalisa; Bartolozzi, Carlo

2013-01-01

Bowel preparation represents an essential part of CT colonography, as the accuracy of the exam is strongly related to the adequacy of colonic cleansing, and a poor bowel preparation may compromise the diagnostic quality even despite optimization of all other acquisition parameters. Residual stool and fluid in the large bowel may affect the interpretation of the exam and may increase the number of false positives and false negatives. In this regard, the majority of patients having undergone CT colonography state that bowel preparation is the most unpleasant part. Unfortunately, to date no definite consensus has been reached about the ideal bowel preparation technique, and there is great variability in preparation strategies across diagnostic centers. The purpose of this review article is to describe the development and evolution of bowel preparation techniques in order to choose the best approach for optimizing the diagnostic quality of CT colonography in each patient

Bowel preparation for CT colonography

Energy Technology Data Exchange (ETDEWEB)

Neri, Emanuele, E-mail: emanuele.neri@med.unipi.it [Diagnostic and Interventional Radiology, University of Pisa (Italy); Lefere, Philippe; Gryspeerdt, Stefaan [Department of Radiology, Stedelijk Ziekenhuis, Roeselare (Belgium); Bemi, Pietro; Mantarro, Annalisa; Bartolozzi, Carlo [Diagnostic and Interventional Radiology, University of Pisa (Italy)

2013-08-15

Bowel preparation represents an essential part of CT colonography, as the accuracy of the exam is strongly related to the adequacy of colonic cleansing, and a poor bowel preparation may compromise the diagnostic quality even despite optimization of all other acquisition parameters. Residual stool and fluid in the large bowel may affect the interpretation of the exam and may increase the number of false positives and false negatives. In this regard, the majority of patients having undergone CT colonography state that bowel preparation is the most unpleasant part. Unfortunately, to date no definite consensus has been reached about the ideal bowel preparation technique, and there is great variability in preparation strategies across diagnostic centers. The purpose of this review article is to describe the development and evolution of bowel preparation techniques in order to choose the best approach for optimizing the diagnostic quality of CT colonography in each patient.

Monitoring the eye lens: which dose quantity is adequate?

International Nuclear Information System (INIS)

Behrens, R; Dietze, G

2010-01-01

Recent epidemiological studies suggest a rather low dose threshold (below 0.5 Gy) for the induction of a cataract of the eye lens. Some other studies even assume that there is no threshold at all. Therefore, protection measures have to be optimized and current dose limits for the eye lens may be reduced in the future. The question of which personal dose equivalent quantity is appropriate for monitoring the dose to the eye lens arises from this situation. While in many countries dosemeters calibrated in terms of the dose equivalent quantity H p (0.07) have been seen as being adequate for monitoring the dose to the eye lens, this might be questionable in the case of reduced dose limits and, thus, it may become necessary to use the dose equivalent quantity H p (3) for this purpose. To discuss this question, the dose conversion coefficients for the equivalent dose of the eye lens (in the following eye lens dose) were determined for realistic photon and beta radiation fields and compared with the values of the corresponding conversion coefficients for the different operational quantities. The values obtained lead to the following conclusions: in radiation fields where most of the dose comes from photons, especially x-rays, it is appropriate to use dosemeters calibrated in terms of H p (0.07) on a slab phantom, while in other radiation fields (dominated by beta radiation or unknown contributions of photon and beta radiation) dosemeters calibrated in terms of H p (3) on a slab phantom should be used. As an alternative, dosemeters calibrated in terms of H p (0.07) on a slab phantom could also be used; however, in radiation fields containing beta radiation with the end point energy near 1 MeV, an overestimation of the eye lens dose by up to a factor of 550 is possible.

Manual of symbols and terminology for physicochemical quantities and units

CERN Document Server

Whiffen, D H

2013-01-01

Manual of Symbols and Terminology for Physicochemical Quantities and Units, 1979 Edition contains physical quantity tabulations of products. The Commission on Symbols, Terminology, and Units is a part of the Division of Physical Chemistry of the International Union of Pure and Applied Chemistry. Its general responsibilities are to secure clarity and precision, and wider agreement in the use of symbols, by chemists in different countries, among physicists, chemists, and engineers, and by editors of scientific journals. This book is composed of 13 chapters, and begins with the determination o

Units for physical quantities used in dosimetry and radiation protection

Energy Technology Data Exchange (ETDEWEB)

Taubert, R; Wagner, S

1976-04-01

The 15th General Conference on Weights and Measures (1975) decided to introduce the name Becquerel for the SI unit of the quantity activity (1 Bq = 1 s/sup -1/) and the name Gray for the SI unit of ionizing radiations (1 Gy = 1 J/kg). The consequences of this latter decision are discussed. The Bundesanstalt is of the opinion that no further names for this unit should be introduced, but that the Gray should be used also for other quantities of the same dimension, especially for the dose equivalent.

Chromatographic cation exchange separation of decigram quantities of californium and other transplutonium elements

Energy Technology Data Exchange (ETDEWEB)

Benker, D.E.; Chattin, F.R.; Collins, E.D.; Knauer, J.B.; Orr, P.B.; Ross, R.G.; Wiggins, J.T.

1980-01-01

Decigram quantities of highly radioactive transplutonium elements are routinely partitioned at TRU by chromatographic elution from cation resin using AHIB eluent. By using two high-pressure ion exchange columns, a small one for the initial loading of the feed and a large one for the elution, batch runs containing up to 200 mg of /sup 252/Cf can be made in about 5 hours (2 hours to load the feed and 3 hours for the elution). The number of effluent product fractions and the amount of actinides that must be collected in intermediate fractions are minimized by monitoring response from a flow-through alpha-detector. This process has been reliable and relatively easy to operate, and will continue to be used for partitioning transplutonium elements at TRU.

Would more social partners leads to enhanced health? The paradox between quantity and quality.

Science.gov (United States)

Xing, Cai; Zhang, Xin; Cheng, Sheung-Tak

2017-09-01

In the current investigation, we examined the association between social network composition (SNC) and mental health, as well as whether quantity and quality of social network could influence mental health differently. The social network quantity and quality of 345 middle-aged and older Chinese adults were measured by the Social Convoy Questionnaire. The Chinese version of the Medical Outcome Studies 36-item Short-Form Health Survey (SF-36) was used to assess mental health while controlling for physical health. It was found that both quantity and quality of social network were associated with mental health, and more specifically that (1) quantity of peripheral partners (PP) was positively associated with mental health; (2) quality of emotionally close social partners (ECSP) influenced mental health the most; and (3) paradoxically, the effect of ECSP quality on mental health depended on quantity of ECSP, that is, participants with more ECSP showed a stronger association between ECSP quality and mental health. The findings replicated and extended previous studies on SNC and suggested that structure/quantity and quality of SNC were both important for mental health. © 2017 The Institute of Psychology, Chinese Academy of Sciences and John Wiley & Sons Australia, Ltd.

Two different preparation techniques for trace element determination of single Daphnia specimen using total reflection x-ray fluorescence analysis (TXRF)

International Nuclear Information System (INIS)

Woelfl, S.; Mages, M.

2000-01-01

Bio accumulation gives first information about the bio-availability of elements in waters and becomes more and more important for the characterization of the water quality. The use of common analytical techniques like ICP-MS and AAS requires large quantities of biologic sample material. Single preparation for example of Daphnia, a common species for bio-test experiments, are hardly possible with these procedures. Therefore alternatively quantitative TXRF element determination of individually prepared Daphnia was developed. Two preparation techniques for single freshwater crustacean specimen from a eutrophic branch of the river Elbe in the 'Rothehorn Park', Magdeburg (Daphnia: dry weight: 10 - 50 μg individuum -1 ) had been tested: (1) Wet preparation: the single Daphnia specimen had been washed with 0.45 μm filtered lake water and put onto quartz sample carriers. After air drying, the body length were determined in order to calculate the dry weight according to previously established body lengths-dry weight relationships. (2) Dry preparation: after collection specimen were washed with 0.45 μm filtered lake water and frozen in liquid nitrogen. The individual lyophilisated dried Daphnia were weighted using an ultrafine micro-balance and put onto quartz sample carriers. After preparation, addition of some μl Gallium standard solution and air drying the individual Daphnia were digested at the quartz sample carriers with 10 μl HNO 3 on a hot plate and dried once more. Finally the element concentrations were determined using a EXTRA IIA total-reflection x-ray fluorescence spectrometer. As a result of these investigations we can conclude that both, the 'dry' and 'wet' preparation method can be used for the element determination in small single crustaceans using TXRF spectrometry. It seems that the 'dry' method yields more precise results, but the wet method is easier to handle in field when samples cannot be fixed with liquid nitrogen. (author)

Unintended consequences of biofuels production?The effects of large-scale crop conversion on water quality and quantity

Science.gov (United States)

Welch, Heather L.; Green, Christopher T.; Rebich, Richard A.; Barlow, Jeannie R.B.; Hicks, Matthew B.

2010-01-01

In the search for renewable fuel alternatives, biofuels have gained strong political momentum. In the last decade, extensive mandates, policies, and subsidies have been adopted to foster the development of a biofuels industry in the United States. The Biofuels Initiative in the Mississippi Delta resulted in a 47-percent decrease in cotton acreage with a concurrent 288-percent increase in corn acreage in 2007. Because corn uses 80 percent more water for irrigation than cotton, and more nitrogen fertilizer is recommended for corn cultivation than for cotton, this widespread shift in crop type has implications for water quantity and water quality in the Delta. Increased water use for corn is accelerating water-level declines in the Mississippi River Valley alluvial aquifer at a time when conservation is being encouraged because of concerns about sustainability of the groundwater resource. Results from a mathematical model calibrated to existing conditions in the Delta indicate that increased fertilizer application on corn also likely will increase the extent of nitrate-nitrogen movement into the alluvial aquifer. Preliminary estimates based on surface-water modeling results indicate that higher application rates of nitrogen increase the nitrogen exported from the Yazoo River Basin to the Mississippi River by about 7 percent. Thus, the shift from cotton to corn may further contribute to hypoxic (low dissolved oxygen) conditions in the Gulf of Mexico.

Spatial and temporal patterns of dissolved organic matter quantity and quality in the Mississippi River Basin, 1997–2013

Science.gov (United States)

Stackpoole, Sarah M.; Stets, Edward G.; Clow, David W.; Burns, Douglas A.; Aiken, George R.; Aulenbach, Brent T.; Creed, Irena F.; Hirsch, Robert M.; Laudon, Hjalmar; Pellerin, Brian; Striegl, Robert G.

2017-01-01

Recent studies have found insignificant or decreasing trends in time-series dissolved organic carbon (DOC) datasets, questioning the assumption that long-term DOC concentrations in surface waters are increasing in response to anthropogenic forcing, including climate change, land use, and atmospheric acid deposition. We used the weighted regressions on time, discharge, and season (WRTDS) model to estimate annual flow-normalized concentrations and fluxes to determine if changes in DOC quantity and quality signal anthropogenic forcing at 10 locations in the Mississippi River Basin. Despite increases in agriculture and urban development throughout the basin, net increases in DOC concentration and flux were significant at only 3 of 10 sites from 1997 to 2013 and ranged between −3.5% to +18% and −0.1 to 19%, respectively. Positive shifts in DOC quality, characterized by increasing specific ultraviolet absorbance at 254 nm, ranged between +8% and +45%, but only occurred at one of the sites with significant DOC quantity increases. Basinwide reductions in atmospheric sulfate deposition did not result in large increases in DOC either, likely because of the high buffering capacity of the soil. Hydroclimatic factors including annual discharge, precipitation, and temperature did not significantly change during the 17-year timespan of this study, which contrasts with results from previous studies showing significant increases in precipitation and discharge over a century time scale. Our study also contrasts with those from smaller catchments, which have shown stronger DOC responses to climate, land use, and acidic deposition. This temporal and spatial analysis indicated that there was a potential change in DOC sources in the Mississippi River Basin between 1997 and 2013. However, the overall magnitude of DOC trends was not large, and the pattern in quantity and quality increases for the 10 study sites was not consistent throughout the basin.

Evaluation of minimum quantity lubrication grinding with nano-particles and recent related patents.

Science.gov (United States)

Li, Changhe; Wang, Sheng; Zhang, Qiang; Jia, Dongzhou

2013-06-01

In recent years, a large number of patents have been devoted to developing minimum quantity lubrication (MQL) grinding techniques that can significantly improve both environmentally conscious and energy saving and costeffective sustainable grinding fluid alternatives. Among them, one patent is about a supply system for the grinding fluid in nano-particle jet MQL, which produced MQL lubricant by adding solid nano-particles in degradable grinding fluid. The MQL supply device turns the lubricant to the pulse drops with fixed pressure, unchanged pulse frequency and the same drop diameter. The drops will be produced and injected in the grinding zone in the form of jet flow under high pressure gas and air seal. As people become increasingly demanding on our environment, minimum quantity lubrication has been widely used in the grinding and processing. Yet, it presents the defect of insufficient cooling performance, which confines its development. To improve the heat transfer efficiency of MQL, nano-particles of a certain mass fraction can be added in the minimum quantity of lubricant oil, which concomitantly will improve the lubrication effects in the processing. In this study, the grinding experiment corroborated the effect of nano-particles in surface grinding. In addition, compared with other forms of lubrication, the results presented that the grinding force, the friction coefficient and specific grinding energy of MQL grinding have been significantly weakened, while G ratio greatly rose. These are attributed to the friction oil-film with excellent anti-friction and anti-wear performance, which is generated nano-particles at the wheel/workpiece interface. In this research, the cooling performance of nano-particle jet MQL was analyzed. Based on tests and experiments, the surface temperature was assayed from different methods, including flood lubricating oil, dry grinding, MQL grinding and nano-particle jet MQL grinding. Because of the outstanding heat transfer

The effect of vial type and cocktail quantity on tritium measurement in LSC

International Nuclear Information System (INIS)

Chen Zhilin; Xing Shixiong; Wang Heyi; Chang Ruimin; Wu Guanyin; Zhou Yinhang

2010-01-01

The effect of sample vial type and cocktail quantity on tritium measurement in liquid scintillation counting is studied in this paper. With both high and low level tritium samples, glass vials allow higher counting rates than plastic vials do. We also present detailed analysis of the way to obtain the optimal counting condition by dispensing different quantity of cocktail into sample vials. Results indicate that the optimal counting condition has little relationship with tritium concentration in the sample. The main factor which influences the counting is the quantity of cocktail added into samples. Figure of merit is employed to access the results, which increases as the quantity of cocktail increasing. But when the ratio of cocktail and sample reaches 2.0, increase of ratio makes little contribution to the counts, and the disintegrations per minute comes nearly to be a constant.

Symbolic Estrangement: Evidence against a Strong Association between Numerical Symbols and the Quantities They Represent

Science.gov (United States)

Lyons, Ian M.; Ansari, Daniel; Beilock, Sian L.

2012-01-01

Are numerals estranged from a sense of the actual quantities they represent? We demonstrate that, irrespective of numerical size or distance, direct comparison of the relative quantities represented by symbolic and nonsymbolic formats leads to performance markedly worse than when comparing 2 nonsymbolic quantities (Experiment 1). Experiment 2…

Radiation quantities, units and measurements. Final report 1999

International Nuclear Information System (INIS)

Wambersie, A.; Allisy, A.; Caswell, R.S.

2000-01-01

The determination of human exposure to radiation and radioactivity, whether arising from environmental exposures, medical practice or industrial activities, requires a fundamental set of quantities and units with which exposures can be specified and the means and ability to make measurements which yield results in terms of these quantities and units. Radiation protection then, as well as effective use of radiation in medical applications, requires the capability to accurately quantify the characteristics and extent of radiation exposure, so that appropriate and useful assessments of the potential health consequences and risks, whether for protection of the public and workers or for diagnosis and treatment of disease, can be formulated. The work carried out via this concerted action on ''Radiation quantities, units and measurements'' has addressed these needs. Measurement of radiation is a complex subject and is a science in itself. Yet many users of radiation who need to make radiation measurements cannot be expected to become experts in this particular field. They need authoritative guidance on how to deal with the measurement problems connected with their particular use of radiation. The work carried out pursuant to this concerted action has resulted in publications that meet this need. Important achievements include the publication of seven new ICRU reports, the completion of all but the printing of three other ICRU reports, completion of the drafting work on two other reports, the development of many others reports and the initiation of seven new activities that will result in ICRU reports representing important future contribution to the needs identified in this project. (orig.)

Quantity assessment of waste in the dismantlement of liquid waste treatment plant and its actual state

International Nuclear Information System (INIS)

Uchiyama, Takafumi; Mitsuhashi, Ishi; Matsumoto, Tetsuo; Morishima, Kayoko; Tanzawa, Tomio

2016-01-01

From the progress of decommissioning project work of Tokyo City University Atomic Energy Research Institute, this paper reports the comparison between the actual amount of the waste generated during dismantlement work at liquid waste treatment facilities and the assessment quantity before starting the dismantlement. The quantity assessment was made on the basis of the installation license application, design specifications, drawings, records, history of use, site investigation results, etc. Since this quantity assessment did not take into account the dismantling contents of reservoir concrete, the assessed quantity of non-radioactive waste (NR waste) did not match the sum of actual NR waste. However, if an actually generated quantity of concrete of radioactive waste was added to the quantity assessment as NR waste, the quantity of actually generated NR waste and that of assessed NR waste were nearly consistent, which verified the validity of this assessment. This method is considered to be able to be utilized in the future quantity assessment of decommissioning work and the like. On the other hand, it was found that the number of drums that were actually stored tended to increase more than the estimated number of drum conversion. In old buildings, it is necessary to take into account the generation of waste other than radioactive materials in the quantity assessment stage and dismantlement stage. (A.O.)

Characteristics and quantities of HIV host cells in human genital tract secretions.

Science.gov (United States)

Politch, Joseph A; Marathe, Jai; Anderson, Deborah J

2014-12-15

Human immunodeficiency virus (HIV)-infected leukocytes have been detected in genital secretions from HIV-infected men and women and may play an important role in the sexual transmission of HIV. However, they have been largely overlooked in studies on mechanisms of HIV transmission and in the design and testing of HIV vaccine and microbicide candidates. This article describes the characteristics and quantities of leukocytes in male and female genital secretions under various conditions and also reviews evidence for the involvement of HIV-infected cells in both horizontal and vertical cell-associated HIV transmission. Additional research is needed in this area to better target HIV prevention strategies. © The Author 2014. Published by Oxford University Press on behalf of the Infectious Diseases Society of America. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Threshold quantities for infectious diseases in periodic environments

NARCIS (Netherlands)

Heesterbeek, J.A.P.; Roberts, M.G.

1995-01-01

In this short note we give threshold quantities that determine the stability of the infection-free steady state for periodic deterministic systems that describe the spread of infectious diseases in populations whose individuals can be divided into a finite number of distinct groups. We concentrate

Comprehensive Evaluation of Large Infrastructure Project Plan with ANP

Institute of Scientific and Technical Information of China (English)

HAN Chuan-feng; CHEN Jian-ye

2005-01-01

Analytic Network Process(ANP) was used in comprehensive evaluation of large infrastructure project plan. A model including social economy, ecological environment, and resources was established with ANP method. The evaluation pattern of hierarchy structure and comprehensive evaluation method for quantity and quality of large infrastructure project were put forward, which provides an effective way to evaluate the large infrastructure project plan. Quantitative analysis indicated that the internal dependence relation of hierarchy structure has influence on ranking results of plan. It is suggested that considering the internal relation can helps managers make effective decisions.

LAVA: Large scale Automated Vulnerability Addition

Science.gov (United States)

2016-05-23

LAVA: Large-scale Automated Vulnerability Addition Brendan Dolan -Gavitt∗, Patrick Hulin†, Tim Leek†, Fredrich Ulrich†, Ryan Whelan† (Authors listed...released, and thus rapidly become stale. We can expect tools to have been trained to detect bugs that have been released. Given the commercial price tag...low TCN) and dead (low liveness) program data is a powerful one for vulnera- bility injection. The DUAs it identifies are internal program quantities

Preparation and characteristics of a Hg-195m/Au-195m generator for first-pass angiography

International Nuclear Information System (INIS)

Bett, R.; Cuninghame, J.G.; Dymond, D.S.; Elliott, A.T.; Flatman, W.; Sims, H.E.; Stone, D.L.; Wills, H.H.

1984-01-01

A Hg-195m/Au-195m generator has been developed for medical use in first pass heart angiography. The mercury parent is bound to a thiol-containing column material from which Au-195m is eluted in dilute sodium cyanide solution. Such generators may have large quantities of activity adsorbed on the column and this can result in radiolytic reactions which cause a decrease of elution efficiency with time. Careful timing of the various operations involved in preparing these generators can help to stop this deterioration. Gold-195m decays to Au-195 which has a half-life of 183 days and it is important to operate the generator in such way as to keep the amount of Au-195 injected into the patient to a minimum. The method of production of these generators is presented. Effects of radiolytic reactions on generator use, and implications of the mass 195 decay chain to ultimate purity of the product are discussed

Quality and quantity: the role of social interactions in individual health

OpenAIRE

Damiano, Fiorillo; Fabio, Sabatini

2011-01-01

The public health literature focusing on the detrimental effects of social isolation has shown that the quantity of social connections is positively correlated with individual health. Drawing on pooled cross-sectional data, we test this hypothesis on a representative sample of the Italian population. Our findings show that, besides the quantity of interactions, it is their quality – as measured by subjective satisfaction derived from relationships with friends – that works as the best pre...

Unified Symmetry and Conserved Quantities of Mechanical System in Phase Space

International Nuclear Information System (INIS)

Fang Jianhui; Ding Ning; Wang Peng

2006-01-01

In this paper, a new symmetry and its conserved quantities of a mechanical system in phase space are studied. The definition of this new symmetry, i.e., a unified one is presented, and the criterion of this symmetry is also given. The Noether, the generalized Hojman and the Mei conserved quantities of the unified symmetry of the system are obtained. The unified symmetry contains the Noether, the Lie and the Mei symmetries, and has more generalized significance.

Improvement on preparation of PS microshells by microencapsulation

International Nuclear Information System (INIS)

Du Kai; You Dan; Zhang Lin; Zhou Lan; Lin Bo

1998-01-01

Density-matched microencapsulation technique was presented. Concentricity, sphericity of microshells prepared by the technique was typically more than 98%, 99% respectively. Reduction of vacuole in the wall and preparation of large diameter microshells were also discussed

Large-scale functional purification of recombinant HIV-1 capsid.

Directory of Open Access Journals (Sweden)

Magdeleine Hung

Full Text Available During human immunodeficiency virus type-1 (HIV-1 virion maturation, capsid proteins undergo a major rearrangement to form a conical core that protects the viral nucleoprotein complexes. Mutations in the capsid sequence that alter the stability of the capsid core are deleterious to viral infectivity and replication. Recently, capsid assembly has become an attractive target for the development of a new generation of anti-retroviral agents. Drug screening efforts and subsequent structural and mechanistic studies require gram quantities of active, homogeneous and pure protein. Conventional means of laboratory purification of Escherichia coli expressed recombinant capsid protein rely on column chromatography steps that are not amenable to large-scale production. Here we present a function-based purification of wild-type and quadruple mutant capsid proteins, which relies on the inherent propensity of capsid protein to polymerize and depolymerize. This method does not require the packing of sizable chromatography columns and can generate double-digit gram quantities of functionally and biochemically well-behaved proteins with greater than 98% purity. We have used the purified capsid protein to characterize two known assembly inhibitors in our in-house developed polymerization assay and to measure their binding affinities. Our capsid purification procedure provides a robust method for purifying large quantities of a key protein in the HIV-1 life cycle, facilitating identification of the next generation anti-HIV agents.

Whither the Nigerian Quantity Surveyors in the Information ...

African Journals Online (AJOL)

The paucity of information on the computing status of the quantity surveyors in Nigeria have been scanty and without empirical substantiation. The basic platform for entry to the information technology gateway is the acquisition, adoption and utilization of the computer. Baseline information is therefore indispensable for the ...

THE RELATION BETWEEN RESUDUE CHLOR QUANTITY AND WATER RELATED DISEASES IN AYDIN

Directory of Open Access Journals (Sweden)

Emine Didem EVCI

2006-02-01

Full Text Available Objectives: The correlation between the residue chlor quantity in water sampled in different points of Aydin province in 2004 and the incidence of infections via water (diarrhea, thyphoid fever, amoebic and bacillary dysentery is studied. Materials and Methods: A retrospective definitive study is performed during June-July 2005. Results: 924 physical and chemical analysis are performed in 2004. In winter season, the mean residue chlor was 0,57±0,10 mg/lt; there were 310 diarrhea cases and a bacillary dysentery case. In summer season, the mean residue chlor was 0,46±0,13 mg/lt; there were 529 diarrhea cases and an amoebic dysentery. Both seasons determined that there was a negative correlation between diarrhea and the residue chlor quantity and there was a poor connection between them and it was statistically unsignificant (for winter r= -0,242, p=0,224; for summer r= -0,148, p=0,480 Conclusion: However there is no determined, expressive connection between diarrhea cases and residue chlor quantity it was seen that as the residue chlor quantity evaluated, the diarrhea cases were reduced. [TAF Prev Med Bull 2006; 5(1.000: 1-7

Results of the regional intercomparison exercise for the determination of operational quantity Hp(d) in Latin America

International Nuclear Information System (INIS)

Saravi, M.; Zaretzky, A.; Lindner, C.; Diaz, J.; Walwyn, G.; Souza, D.; Amorin, R.; Gregory, B.; Papadopulos, S.; Meghzifene, A.; Ferruz Cruz, P.; Cruz Suarez, R.

2005-01-01

Full text: Several intercomparison exercises were organized by the International Atomic Energy Agency (IAEA) on the determination of operational quantities at the regional or interregional basis. These exercises revealed significant differences in the approach, methods and assumptions, and consequently in the measurement results obtained by participating laboratories. In the Latin America region, an intercomparison for determination of operational quantity Hp(10), organized within the frame of a technical cooperation regional project, was completed mid-2004, as a follow-up to previous exercises carried out during the 1990s. Eighteen laboratories from 19 member states participated in the first phase; the second phase grouped 15 laboratories from 16 member states. Dosimeter irradiations (5 different radiation qualities for photon simulating workplace fields) were done by 4 Secondary Standards Dosimetry Laboratories (SSDL). The preparations for the exercise involved an audit by the IAEA SSDL, where reference irradiations were provided to all participants for verification of their system. During the first phase (2002/03), only 9 out of 18 laboratories met the performance requirements for such monitoring services. Necessary corrective actions and procedure verification were implemented, and staff involved in these evaluations were subsequently trained. During the second phase (2004), 11 out of 15 laboratories fulfilled the performance criteria. The 4 laboratories still having difficulties in assessing occupational exposure participated in a results meeting, during which problem areas were identified. An ongoing technical cooperation mission is expected to assist these laboratories accordingly. There has been a definite improvement in the second phase and most laboratories demonstrated a good performance in the quantity tested. The technical results clearly show that the laboratories' capability in assessing occupational exposure from external sources of radiation is

Ovarian cyst fluid of serous ovarian tumors contains large quantities of the brain amino acid N-acetylaspartate.

OpenAIRE

Kolwijck, E.; Wevers, R.A.; Engelke, U.F.H.; Woudenberg, J.; Bulten, J.; Blom, H.J.; Massuger, L.F.A.G.

2010-01-01

BACKGROUND: In humans, N-acetyl L-aspartate (NAA) has not been detected in other tissues than the brain. The physiological function of NAA is yet undefined. Recently, it has been suggested that NAA may function as a molecular water pump, responsible for the removal of large amounts of water from the human brain. Ovarian tumors typically present as large cystic masses with considerable fluid accumulation. METHODOLOGY AND PRINCIPAL FINDINGS: Using Gas Chromatography-Mass Spectrometry, we demons...

Quantity and quality limit detritivore growth: mechanisms revealed by ecological stoichiometry and co-limitation theory.

Science.gov (United States)

Halvorson, Halvor M; Sperfeld, Erik; Evans-White, Michelle A

2017-12-01

Resource quantity and quality are fundamental bottom-up constraints on consumers. Best understood in autotroph-based systems, co-occurrence of these constraints may be common but remains poorly studied in detrital-based systems. Here, we used a laboratory growth experiment to test limitation of the detritivorous caddisfly larvae Pycnopsyche lepida across a concurrent gradient of oak litter quantity (food supply) and quality (phosphorus : carbon [P:C ratios]). Growth increased simultaneously with quantity and quality, indicating co-limitation across the resource gradients. We merged approaches of ecological stoichiometry and co-limitation theory, showing how co-limitation reflected shifts in C and P acquisition throughout homeostatic regulation. Increased growth was best explained by elevated consumption rates and improved P assimilation, which both increased with elevated quantity and quality. Notably, C assimilation efficiencies remained unchanged and achieved maximum 18% at low quantity despite pronounced C limitation. Detrital C recalcitrance and substantive post-assimilatory C losses probably set a minimum quantity threshold to achieve positive C balance. Above this threshold, greater quality enhanced larval growth probably by improving P assimilation toward P-intensive growth. We suggest this interplay of C and P acquisition contributes to detritivore co-limitation, highlighting quantity and quality as potential simultaneous bottom-up controls in detrital-based ecosystems, including under anthropogenic change like nutrient enrichment. © 2017 by the Ecological Society of America.

A Neural Network Approach to Fluid Quantity Measurement in Dynamic Environments

CERN Document Server

Terzic, Edin; Nagarajah, Romesh; Alamgir, Muhammad

2012-01-01

Sloshing causes liquid to fluctuate, making accurate level readings difficult to obtain in dynamic environments. The measurement system described uses a single-tube capacitive sensor to obtain an instantaneous level reading of the fluid surface, thereby accurately determining the fluid quantity in the presence of slosh. A neural network based classification technique has been applied to predict the actual quantity of the fluid contained in a tank under sloshing conditions.   In A neural network approach to fluid quantity measurement in dynamic environments, effects of temperature variations and contamination on the capacitive sensor are discussed, and the authors propose that these effects can also be eliminated with the proposed neural network based classification system. To examine the performance of the classification system, many field trials were carried out on a running vehicle at various tank volume levels that range from 5 L to 50 L. The effectiveness of signal enhancement on the neural network base...

Adaptation of the present concept of dosimetric radiation protection quantities for external radiation to radiation protection practice

International Nuclear Information System (INIS)

Boehm, J.; Thompson, I. M. G.

2004-01-01

The present concept of dosimetric radiation protection quantities for external radiation is reviewed. For everyday application of the concept some adaptations are recommended. The check of the compliance with dose limits should be performed either by the comparison with values of the respective operational quantities directly or by the calculation of the protection quantity by means of the operational quantity, the appertaining conversion coefficient and additional information of the radiation field. Only four operational quantities are regarded to be sufficient for most applications in radiation protection practice. The term equivalent should be used in the connection dose equivalent only. Proposals are made for names of frequently used operational quantities which are denoted up to now by symbols only. (authors)

By Default: The Effect of Prepopulated Prescription Quantities on Opioid Prescribing in the Emergency Department.

Science.gov (United States)

Santistevan, Jamie R; Sharp, Brian R; Hamedani, Azita G; Fruhan, Scott; Lee, Andrew W; Patterson, Brian W

2018-03-01

Opioid prescribing patterns have come under increasing scrutiny with the recent rise in opioid prescriptions, opioid misuse and abuse, and opioid-related adverse events. To date, there have been limited studies on the effect of default tablet quantities as part of emergency department (ED) electronic order entry. Our goal was to evaluate opioid prescribing patterns before and after the removal of a default quantity of 20 tablets from ED electronic order entry. We performed a retrospective observational study at a single academic, urban ED with 58,000 annual visits. We identified all adult patients (18 years or older) seen in the ED and discharged home with prescriptions for tablet forms of hydrocodone and oxycodone (including mixed formulations with acetaminophen). We compared the quantity of tablets prescribed per opioid prescription 12 months before and 10 months after the electronic order-entry prescription default quantity of 20 tablets was removed and replaced with no default quantity. No specific messaging was given to providers, to avoid influencing prescribing patterns. We used two-sample Wilcoxon rank-sum test, two-sample test of proportions, and Pearson's chi-squared tests where appropriate for statistical analysis. A total of 4,104 adult patients received discharge prescriptions for opioids in the pre-intervention period (151.6 prescriptions per 1,000 discharged adult patients), and 2,464 post-intervention (106.69 prescriptions per 1,000 discharged adult patients). The median quantity of opioid tablets prescribed decreased from 20 (interquartile ration [IQR] 10-20) to 15 (IQR 10-20) (pdefault quantity. While the most frequent quantity of tablets received in both groups was 20 tablets, the proportion of patients who received prescriptions on discharge that contained 20 tablets decreased from 0.5 (95% confidence interval [CI] [0.48-0.52]) to 0.23 (95% CI [0.21-0.24]) (pdefault quantity removal. Although the median number of tablets differed significantly

Quality or Quantity: A Statement for Teacher Training in Turkey

Directory of Open Access Journals (Sweden)

Ali AZAR

2011-01-01

Full Text Available Developed countries are initiating and implementing effective and appropriate technics in the field of teacher training. In Turkey, much research has been done in order to determine the qualification of teachers and, by this way, to train qualified teachers. Ministry of Education, Turkish Council of Higher Education, Faculties of Education and Faculties of Sciences have cooperated some certification systems, however, the research which is not supported by preliminary studies but exposured to political coercions lowered the quality of education. Besides, quantity is increased by pedagogical formation programs. In this study, Turkish teacher training system is analyzed with respect to quantity and quality.

Light interventions: a novel approach for sustaining sleep quality and quantity of elite swimmers under conditions of shifted circadian rhythm

DEFF Research Database (Denmark)

Argyraki, Aikaterini; Andersen, Jakob Hildebrandt; Johansen, Lars

2017-01-01

, efficiency, latency, percentages of light, deep or REM sleep were the variables under investigation. The sleep output was modeled (ANOVA) with subject as a random effect and phase as fixed effect. It was observed that the light program during the intervention phase significantly enabled the conservation...... of sleep quantity and quality of the swimmers, despite the shifted circadian rhythm. The hypothesis of no effect of phase of experiment on sleep duration, efficiency, latency, percentage of light, deep and REM sleep were all accepted with p. values 0.17, 0.53, 0.90, 0.38, 0.57 and 0.52, respectively......For the 2016 Olympics at Rio De Janeiro the Danish swimmers was facing a very important problem, how to maintain a good sleep quality, quantity and high performance potential, while being subject to large shift in circadian rhythm. In the present study we suggest an alternative approach...

Appraisal of Information Technology Requirements in Quantity Surveying Firms in Northern Nigeria

Directory of Open Access Journals (Sweden)

Y. U. Datti

2017-06-01

Full Text Available A worrisome trend in the adoption of emerging technologies for competitive advantages and improved productivities by QSs have been observed in that there is overwhelming evidence that there is an increasing usage of IT in quantity surveying firms but little or no noticeable benefits on the practice. It however becomes pertinent to ask then, that despite the increases adoption of computing and telecommunication technologies, why isn’t there any noticeable change due to the impacts of IT in the Nigerian Construction Industry with particular reference to Quantity Surveying practices. The study appraised the requirement of IT in quantity surveying practice in Nigeria. It examined the position of IT in quantity surveying firms in terms of its requirement and analyzed IT requirements-based problem constraining quantity surveying firms. The study is a survey research designed to obtain information on information technology in QS firms. A self-administered questionnaire was employed to quantity surveyors in consulting firms for responses. Responses were returned and analyzed using severity index and later ranked in order of importance. The results indicate a high level of computerization of professional services among the firms with greater number of their computers being networked. However, despite high level of networking of available computers, sharing of printers and other scarce tools/technologies are not established. Compared to developed countries such as Canada, Australia, United Kingdom and USA, the position of IT requirements in QS firms in Nigeria can be said to be at basic level with organization possessing and applying basic IT tools and technologies (e.g. scanners, digital cameras, dvd/cd-rom, general purpose software, QS application software, chat programs etc. in their daily operation and processes. While most firms are progressing toward intermediate level by possessing intermediate IT tools and technologies (e.g. teleconferencing

Characteristics Data Base: Programmer's guide to the LWR Quantities Data Base

International Nuclear Information System (INIS)

Jones, K.E.; Moore, R.S.

1990-08-01

The LWR Quantities Data Base is a menu-driven PC data base developed as part of OCRWM's waste, technical data base on the characteristics of potential repository wastes, which also includes non-LWR spent fuel, high-level and other materials. This programmer's guide completes the documentation for the LWR Quantities Data Base, the user's guide having been published previously. The PC data base itself may be requested from the Oak Ridge National Laboratory, using the order form provided in Volume 1 of publication DOE/RW-0184

Robot system for preparing lymphocyte chromosome

International Nuclear Information System (INIS)

Hayata, Isamu; Furukawa, Akira; Yamamoto, Mikio; Sato, Koki; Tabuchi, Hiroyoshi; Okabe, Nobuo.

1992-01-01

Towards the automatization of the scoring of chromosome aberrations in radiation dosimetry with the emphasis on the improvement of biological preparations, the conventional culture and harvesting method was modified. Based on this modified method, a culture and harvest robotic system (CHROSY) for preparing lymphocyte chromosome was developed. The targeted points of the modification are as in the preparing lymphocyte chromosome was developed. The targeted points of the modification are as in the following. 1) Starting culture with purified lymphocytes in a fixed cell number. 2) Avoiding the loss of cells in changing the liquids following centrifugalization. 3) Keeping the quantity of the liquids to be applied to the treatments of cells fixed. 4) Building a system even a beginner can handle. System features are as follows. 1) Operation system: Handling robot having 5 degrees of freedom; a rotator incubator with an automatic sliding door; units for setting and removing pipette tips; a centrifuge equipped with a position adjuster and an automatic sliding door; two aluminium block baths; two nozzles as pipettes and aspirators connected to air pumps; a capping unit with a nozzle for CO 2 gas; a compressor; and an air manipulated syringe. 2) Control system; NEC PC-9801RX21 with CRT; and program written in Basic and Assembly languages on MS-DOS. It took this system 2 hours and 25 minutes to harvest 2 cultures. A fairly good chromosome slide was made from the sample harvested by CHROSY automatically. (author)

EFFECT OF SALES PROMOTION SCHEMES ON PURCHASE QUANTITY: A STUDY OF MALAYSIAN CONSUMERS

Directory of Open Access Journals (Sweden)

Hawa JALLOW

2016-11-01

Full Text Available The research aims to study the effect of sales promotion on the purchase quantity and recommend sales promotional means and methods that could improve sales for retail sector in Malaysia. The impact of coupons, bonus packages, premiums, free samples and price discount is measured on purchase quantity of Malaysian retail consumers. Empirical data is gathered from 150 respondents using self-administered questionnaire and analyzed using correlation and regression analysis to examine the relationship between variables. The findings of the study reveal that all independent variables influences purchase quantity positively and significantly while free samples and price discounts are most influential factors for Malaysian market.

Coordinated Lot-sizing and Dynamic Prizing under a Supplier All-units Quantity Discount

Directory of Open Access Journals (Sweden)

Sandra Transchel

2008-05-01

Full Text Available We consider an economic order quantity model where the supplier offers an all-units quantity discount and a price sensitive customer demand. We compare a decentralized decision framework where selling price and replenishment policy are determined independently to simultaneous decision making. Constant and dynamic pricing are distinguished. We derive structural properties and develop algorithms that determine the optimal pricing and replenishment policy and show how quantity discounts not only influence the purchasing strategy but also the pricing policy. A sensitivity analysis indicates the impact of the fixed-holding cost ratio, the discount policy, and the customers' price sensitivity on the optimal decisions.

QUANTITY DISCOUNTS IN SUPPLIER SELECTION PROBLEM BY USE OF FUZZY MULTI-CRITERIA PROGRAMMING

Directory of Open Access Journals (Sweden)

Tunjo Perić

2011-02-01

Full Text Available Supplier selection in supply chain is a multi-criteria problem that involves a number of quantitative and qualitative factors. This paper deals with a concrete problem of flour purchase by a company that manufactures bakery products and the purchasing price of flour depends on the quantity ordered. The criteria for supplier selection and quantities supplied by individual suppliers are: purchase costs, product quality and reliability of suppliers. The problem is solved using a model that combines revised weighting method and fuzzy multi-criteria linear programming (FMCLP. The paper highlights the efficiency of the proposed methodology in conditions when purchasing prices depend on order quantities.

Determination of the quantity of acetyl CoA carboxylase by [14C]methyl avidin binding

International Nuclear Information System (INIS)

Roman-Lopez, C.R.; Goodson, J.; Allred, J.B.

1987-01-01

Conditions are described under which monomeric [ 14 C]methyl avidin binds to SDS-denatured biotin enzymes and remains bound through polyacrylamide gel electrophoresis. The location of radioactive proteins on the dried gel was determined by fluorography and their identity was established by subunit molecular weight. The relative quantity of bound radioactive avidin, stoichiometrically equivalent to the molar quantity of biotin protein, can be determined by scanning the fluorograph with a soft laser densitometer. To determine the absolute quantity of biotin protein, the radioactive areas of the dried gel were cut out, resolubilized, and assayed for radioactivity. Since the specific radioactivity of the [ 14 C]methyl avidin was known, the quantity of avidin bound and therefore the quantity of biotin enzyme could be calculated. The method is illustrated by the analysis of purified acetyl CoA carboxylase and is applied to the analysis of biotin enzymes in isolated rat liver mitochondria

The impact of symbolic and non-symbolic quantity on spatial learning.

Directory of Open Access Journals (Sweden)

Koleen McCrink

Full Text Available An implicit mapping of number to space via a "mental number line" occurs automatically in adulthood. Here, we systematically explore the influence of differing representations of quantity (no quantity, non-symbolic magnitudes, and symbolic numbers and directional flow of stimuli (random flow, left-to-right, or right-to-left on learning and attention via a match-to-sample working memory task. When recalling a cognitively demanding string of spatial locations, subjects performed best when information was presented right-to-left. When non-symbolic or symbolic numerical arrays were embedded in these spatial locations, and mental number line congruency prompted, this effect was attenuated and in some cases reversed. In particular, low-performing female participants who viewed increasing non-symbolic number arrays paired with the spatial locations exhibited better recall for left-to-right directional flow information relative to right-to-left, and better processing for the left side of space relative to the right side of space. The presence of symbolic number during spatial learning enhanced recall to a greater degree than non-symbolic number--especially for female participants, and especially when cognitive load is high--and this difference was independent of directional flow of information. We conclude that quantity representations have the potential to scaffold spatial memory, but this potential is subtle, and mediated by the nature of the quantity and the gender and performance level of the learner.

The orientation distribution of tunneling-related quantities

Science.gov (United States)

Seif, W. M.; Refaie, A. I.; Botros, M. M.

2018-03-01

In the nuclear tunneling processes involving deformed nuclei, most of the tunneling-related quantities depend on the relative orientations of the participating nuclei. In the presence of different multipole deformations, we study the variation of a few relevant quantities for the α-decay and the sub-barrier fusion processes, in an orientation degree of freedom. The knocking frequency and the penetration probability are evaluated within the Wentzel-Kramers-Brillouin approximation. The interaction potential is calculated with Skyrme-type nucleon-nucleon interaction. We found that the width of the potential pocket, the Coulomb barrier radius, the penetration probability, the α-decay width, and the fusion cross-section follow consistently the orientation-angle variation of the radius of the deformed nucleus. The orientation distribution patterns of the pocket width, the barrier radius, the logarithms of the penetrability, the decay width, and the fusion cross-section are found to be highly analogous to pattern of the deformed-nucleus radius. The curve patterns of the orientation angle distributions of the internal pocket depth, the Coulomb barrier height and width, as well as the knocking frequency simulate inversely the variation of the deformed nucleus radius. The predicted orientation behaviors will be of a special interest in predicting the optimum orientations for the tunneling processes.

Preparation and Photoluminescence of ZnO Comb-Like Structure and Nanorod Arrays

Science.gov (United States)

Yin, Song; Chen, Yi-qing; Su, Yong; Zhou, Qing-tao

2007-06-01

A large quantity of Zinc oxide (ZnO) comb-like structure and high-density well-aligned ZnO nanorod arrays were prepared on silicon substrate via thermal evaporation process without any catalyst. The morphology, growth mechanism, and optical properties of the both structures were investigated using XRD, SEM, TEM and PL. The resulting comb-teeth, with a diameter about 20 nm, growing along the [0001] direction have a well-defined epitaxial relationship with the comb ribbon. The ZnO nanorod arrays have a diameter about 200 nm and length up to several micrometers growing approximately vertical to the Si substrate. A ZnO film was obtained before the nanorods growth. A growth model is proposed for interpreting the growth mechanism of comb-like zigzag-notch nanostructure. Room temperature photoluminescence measurements under excitation wavelength of 325 nm showed that the ZnO comb-like nanostructure has a weak UV emission at around 384 nm and a strong green emission around 491 nm, which correspond to a near band-edge transition and the singly ionized oxygen vacancy, respectively. In contrast, a strong and sharp UV peak and a weak green peak was obtained from the ZnO nanorod arrays.

A Comparative Study of Face Milling of D2 Steel Using Al2O3 Based Nanofluid Minimum Quantity Lubrication and Minimum Quantity Lubrication

Directory of Open Access Journals (Sweden)

Muhammad Ahsan Ul Haq

2018-03-01

Full Text Available This study aims to investigate the effects of process parameters feed, depth of cut and flow rate, on the temperature during face milling of the D2 tool steel under two different lubricant conditions, Minimum Quantity Lubrication (MQL and Nanofluid Minimum Quantity Lubrication (NFMQL. Distilled water with the flow rate range 200-400 ml/hr was used in MQL. 2% by weight concentration of Al2O3 nanoparticles with distilled water as the base fluid used as NFMQL with same flow rate. Response surface methodology RSM central composite design CCD was used to design experiment run, modeling, and analysis. ANOVA was used for the adequacy and validation of the system. The comparison shows that NFMQL condition reduced more temperature during machining.

An Adaptive Information Quantity-Based Broadcast Protocol for Safety Services in VANET

Directory of Open Access Journals (Sweden)

Wenjie Wang

2016-01-01

Full Text Available Vehicle-to-vehicle communication plays a significantly important role in implementing safe and efficient road traffic. When disseminating safety messages in the network, the information quantity on safety packets changes over time and space. However, most of existing protocols view each packet the same to disseminate, preventing vehicles from collecting more recent and precise safety information. Hence, an information quantity-based broadcast protocol is proposed in this paper to ensure the efficiency of safety messages dissemination. In particular, we propose the concept of emergency-degree to evaluate packets’ information quantity. Then we present EDCast, an emergency-degree-based broadcast protocol. EDCast differentiates each packet’s priority for accessing the channel based on its emergency-degree so as to provide vehicles with more safety information timely and accurately. In addition, an adaptive scheme is presented to ensure fast dissemination of messages in different network condition. We compare the performance of EDCast with those of three other representative protocols in a typical highway scenario. Simulation results indicate that EDCast achieves higher broadcast efficiency and less redundancy with less delivery delay. What we found demonstrates that it is feasible and necessary for incorporating information quantity of messages in designing an efficient safety message broadcast protocol.

A modular method to handle multiple time-dependent quantities in Monte Carlo simulations

International Nuclear Information System (INIS)

Shin, J; Faddegon, B A; Perl, J; Schümann, J; Paganetti, H

2012-01-01

A general method for handling time-dependent quantities in Monte Carlo simulations was developed to make such simulations more accessible to the medical community for a wide range of applications in radiotherapy, including fluence and dose calculation. To describe time-dependent changes in the most general way, we developed a grammar of functions that we call ‘Time Features’. When a simulation quantity, such as the position of a geometrical object, an angle, a magnetic field, a current, etc, takes its value from a Time Feature, that quantity varies over time. The operation of time-dependent simulation was separated into distinct parts: the Sequence samples time values either sequentially at equal increments or randomly from a uniform distribution (allowing quantities to vary continuously in time), and then each time-dependent quantity is calculated according to its Time Feature. Due to this modular structure, time-dependent simulations, even in the presence of multiple time-dependent quantities, can be efficiently performed in a single simulation with any given time resolution. This approach has been implemented in TOPAS (TOol for PArticle Simulation), designed to make Monte Carlo simulations with Geant4 more accessible to both clinical and research physicists. To demonstrate the method, three clinical situations were simulated: a variable water column used to verify constancy of the Bragg peak of the Crocker Lab eye treatment facility of the University of California, the double-scattering treatment mode of the passive beam scattering system at Massachusetts General Hospital (MGH), where a spinning range modulator wheel accompanied by beam current modulation produces a spread-out Bragg peak, and the scanning mode at MGH, where time-dependent pulse shape, energy distribution and magnetic fields control Bragg peak positions. Results confirm the clinical applicability of the method. (paper)

Terms and definitions in the field of radiological technique. Dose quantities and units

International Nuclear Information System (INIS)

1985-12-01

The standard gives the terms and definitions of concepts, dose quantities and units. The radiation field condition 'secondary electron equilibrium', which forms part of the definition of standard ion dose, is given more precisely. The term 'free in air' is used in its original meaning, i.e. characterization of measuring conditions excluding avoidable stray radiation, which deviates from DIN 6814, part 3/06.72. Dosemeters for measurement of standard ion dose of air kerma are calibrated 'free in air', but this calibration condition is not part of the quantity definition. The quantities standard ion dose or air kerma therefore can also be measured in any other material. The qunatitative relationships between standard ion dose and the quantities 'exposure' and air kerma, as given in the ICRU publication 33 'Quantities and Units' (1980), are explained. The standard introduces the SI units Gray (for energy dose), Sievert (for dose equivalent), and Becquerel (for the activity of a radioactive substance). As the change to the SI units conceals the approximated equality of the numerical values of the standrd ion dose of photon radiation in roentgen, of the energy dose for soft tissue in rad, and of the dose equivalent in rem, new definitions are given in accordance with ICRU 33 for the quantities specified dose rate, dose rate constant, and area exposure product. These definitions use the terms 'energy dose' and 'kerma'. The dose concepts applied in the field of radiation protection, especially ambient dose and individual dose, are defined as dose equivalents in compliance with the Radiation Protection Ordinance. The relevant sections present information on the conversion of standard ion dose values to the corresponding values of kerma, energy dose, or dose equivalent. (orig./HP) [de

Strategic Planning in Irish Quantity Surveying Pracitces

OpenAIRE

Murphy, Roisin

2011-01-01

The role and usefulness of strategic planning has been well documented over several decades of strategic management research. Despite the significant body of existing knowledge in the field of strategic planning, there remains a paucity of investigation into the construction sector, specifically in Professional Service Firms (PSF’s) operating within it. The aim of this research was to ascertain the type, scope and extent of strategic planning within Irish Quantity Surveying (QS) practices and...

Effects of short-term warming and nitrogen addition on the quantity and quality of dissolved organic matter in a subtropical Cunninghamia lanceolata plantation

Science.gov (United States)

Yuan, Xiaochun; Si, Youtao; Lin, Weisheng; Yang, Jingqing; Wang, Zheng; Zhang, Qiufang; Qian, Wei; Yang, Yusheng

2018-01-01

Increasing temperature and nitrogen (N) deposition are two large-scale changes projected to occur over the coming decades. The effects of these changes on dissolved organic matter (DOM) are largely unknown. This study aimed to assess the effects of warming and N addition on the quantity and quality of DOM from a subtropical Cunninghamia lanceolata plantation. Between 2014 and 2016, soil solutions were collected from 0–15, 15–30, and 30–60 cm depths by using a negative pressure sampling method. The quantity and quality of DOM were measured under six different treatments. The spectra showed that the DOM of the forest soil solution mainly consisted of aromatic protein-like components, microbial degradation products, and negligible amounts of humic-like substances. Warming, N addition, and warming + N addition significantly inhibited the concentration of dissolved organic carbon (DOC) in the surface (0–15 cm) soil solution. Our results suggested that warming reduced the amount of DOM originating from microbes. The decrease in protein and carboxylic acid contents was mostly attributed to the reduction of DOC following N addition. The warming + N addition treatment showed an interactive effect rather than an additive effect. Thus, short-term warming and warming + N addition decreased the quantity of DOM and facilitated the migration of nutrients to deeper soils. Further, N addition increased the complexity of the DOM structure. Hence, the loss of soil nutrients and the rational application of N need to be considered in order to prevent the accumulation of N compounds in soil. PMID:29360853

Voltammetric determination of copper in selected pharmaceutical preparations--validation of the method.

Science.gov (United States)

Lutka, Anna; Maruszewska, Małgorzata

2011-01-01

It were established and validated the conditions of voltammetric determination of copper in pharmaceutical preparations. The three selected preparations: Zincuprim (A), Wapń, cynk, miedź z wit. C (B), Vigor complete (V) contained different salts and different quantity of copper (II) and increasing number of accompanied ingredients. For the purpose to transfer copper into solution, the samples of powdered tablets of the first and second preparation were undergone extraction and of the third the mineralization procedures. The concentration of copper in solution was determined by differential pulse voltammetry (DP) using comparison with standard technique. In the validation process, the selectivity, accuracy, precision and linearity of DP determination of copper in three preparations were estimated. Copper was determined within the concentration range of 1-9 ppm (1-9 microg/mL): the mean recoveries approached 102% (A), 100% (B), 102% (V); the relative standard deviations of determinations (RSD) were 0.79-1.59% (A), 0.62-0.85% (B) and 1.68-2.28% (V), respectively. The mean recoveries and the RSDs of determination satisfied the requirements for the analyte concentration at the level 1-10 ppm. The statistical verification confirmed that the tested voltammetric method is suitable for determination of copper in pharmaceutical preparation.

Deep groundwater quantity and quality in the southwestern US

Science.gov (United States)

Kang, M.; Ayars, J. E.; Jackson, R. B.

2017-12-01

Groundwater demands are growing in many arid regions and adaptation through the use of non-traditional resources during extreme droughts is increasingly common. One such resource is deep groundwater, which we define as deeper than 300 m and up to several kilometer-depths. Although deep groundwater has been studied in the context of oil and gas, geothermal, waste disposal, and other uses, it remains poorly characterized, especially for the purposes of human consumption and irrigation uses. Therefore, we evaluate deep groundwater quantity and quality within these contexts. We compile and analyze data from water management agencies and oil and gas-based sources for the southwestern US, with a detailed look at California's Central Valley. We also use crop tolerance thresholds to evaluate deep groundwater quality for irrigation purposes. We find fresh and usable groundwater volume estimates in California's Central Valley to increase by three- and four-fold respectively when depths of up to 3 km are considered. Of the ten basins in the southwestern US with the most data, we find that the Great Basin has the greatest proportions of fresh and usable deep groundwater. Given the potentially large deep groundwater volumes, it is important to characterize the resource, guard against subsidence where extracted, and protect it for use in decades and centuries to come.

Large scale calculations for hadron spectroscopy

International Nuclear Information System (INIS)

Rebbi, C.

1985-01-01

The talk reviews some recent Monte Carlo calculations for Quantum Chromodynamics, performed on Euclidean lattices of rather large extent. Purpose of the calculations is to provide accurate determinations of quantities, such as interquark potentials or mass eigenvalues, which are relevant for hadronic spectroscopy. Results obtained in quenched QCD on 16 3 x 32 lattices are illustrated, and a discussion of computational resources and techniques required for the calculations is presented. 18 refs.,3 figs., 2 tabs

Large-scale preparation of sulfated polysaccharides with anti-angionenic and anti-inflammatory properties from Antrodia cinnamomia.

Science.gov (United States)

Cheng, Jing-Jy; Chao, Chi-Hsein; Lu, Mei-Kuang

2018-07-01

Sulfated polysaccharides (SPSs) were isolated from 0.5mM potassium-sulfate fed Antrodia cinnamomea. We investigated the chemical properties and bio-activities of the five different fractions (SPS-K1, SPS-K2, SPS-K3, SPS-K4, and SPS-K5) with molecular weights ranging from 0.51 to 523.48kDa. SPS-K3 was consisted mainly of glucose, galactose and sulfate in a molar ratio of 15:1:30 with Mn value of 6.82kDa. It showed maximal inhibition of the tumor necrosis factor (TNF-α), interleukin-1beta (IL-1β) and interleukin-6 (IL-6) on bacterial LPS-induced inflammation in RAW264.7 macrophage and the production was recorded as 26.19 and 51.06%, respectively. SPS-K2 showed inhibition of endothelial cell tube formation in an in vitro assay of angiogenesis, and IC 50 was determined to be 160.92μg/ml. Large-scale preparation of SPS was performed in the 3-L fermentation of A. cinnamomea and the yield of the SPS was 5.38%. The area percentage of high-molecular-weight SPSs (1470-1590kDa) covered almost half of the SPSs mixture characterized by size exclusion column chromatography. The SPSs from fermented A. cinnamomea had significant inhibition on TNF-α, IL-1β and IL-6 production. This study is the first report to large-scale produce SPSs and demonstrates sulfated galactoglucan with strong anti-inflammatory activity. Copyright © 2018 Elsevier B.V. All rights reserved.

Integrated massively parallel sequencing of 15 autosomal STRs and Amelogenin using a simplified library preparation approach.

Science.gov (United States)

Xue, Jian; Wu, Riga; Pan, Yajiao; Wang, Shunxia; Qu, Baowang; Qin, Ying; Shi, Yuequn; Zhang, Chuchu; Li, Ran; Zhang, Liyan; Zhou, Cheng; Sun, Hongyu

2018-04-02

Massively parallel sequencing (MPS) technologies, also termed as next-generation sequencing (NGS), are becoming increasingly popular in study of short tandem repeats (STR). However, current library preparation methods are usually based on ligation or two-round PCR that requires more steps, making it time-consuming (about 2 days), laborious and expensive. In this study, a 16-plex STR typing system was designed with fusion primer strategy based on the Ion Torrent S5 XL platform which could effectively resolve the above challenges for forensic DNA database-type samples (bloodstains, saliva stains, etc.). The efficiency of this system was tested in 253 Han Chinese participants. The libraries were prepared without DNA isolation and adapter ligation, and the whole process only required approximately 5 h. The proportion of thoroughly genotyped samples in which all the 16 loci were successfully genotyped was 86% (220/256). Of the samples, 99.7% showed 100% concordance between NGS-based STR typing and capillary electrophoresis (CE)-based STR typing. The inconsistency might have been caused by off-ladder alleles and mutations in primer binding sites. Overall, this panel enabled the large-scale genotyping of the DNA samples with controlled quality and quantity because it is a simple, operation-friendly process flow that saves labor, time and costs. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Quantity and Quality of Inhaled Dose Predicts Immunopathology in Tuberculosis

Directory of Open Access Journals (Sweden)

Kevin Patrick Fennelly

2015-06-01

Full Text Available Experimental animal models of tuberculosis (TB have convincingly demonstrated that inhaled dose predicts immunopathology and survival. In contrast, the importance of inhaled dose has generally not been appreciated in TB epidemiology, clinical science, or the practice of TB control. Infectiousness of TB patients has traditionally been assessed using microscopy for acid-fast bacilli in the sputum, which should be considered only a risk factor. We have recently demonstrated that cough aerosol cultures from index cases with pulmonary TB are the best predictors of new infection among household contacts. We suggest that cough aerosols of M. tuberculosis are the best surrogates of inhaled dose, and we hypothesize that the quantity of cough aerosols is associated with TB infection versus disease. Although several factors affect the quality of infectious aerosols, we propose that the particle size distribution of cough aerosols is an important predictor of primary upper airway disease and cervical lymphadenitis and of immune responses in exposed hosts. We hypothesize that large droplet aerosols (> 5 microns containing M. tuberculosis deposit in the upper airway and can induce immune responses without establishing infection. We suggest that this may partially explain the large proportion of humans who never develop TB disease in spite of having immunological evidence of M. tuberculosis infection (e.g. positive TST or IGRA. If these hypotheses are proven true, they would alter the current paradigm of latent TB infection and reactivation, further demonstrating the need for better biomarkers or methods of assessing TB infection and the risk of developing disease.

MAD about the Large Magellanic Cloud Preparing for the era of Extremely Large Telescopes

NARCIS (Netherlands)

Fiorentino, G.; Tolstoy, E.; Diolaiti, E.; Valenti, E.; Cignoni, M.; Mackey, A. D.

We present J, H, K-s photometry from the the Multi conjugate Adaptive optics Demonstrator (MAD), a visitor instrument at the VLT, of a resolved stellar population in a small crowded field in the bar of the Large Magellanic Cloud near the globular cluster NGC 1928. In a total exposure time of 6, 36

Estimating waste disposal quantities from raw waste samples

International Nuclear Information System (INIS)

Negin, C.A.; Urland, C.S.; Hitz, C.G.; GPU Nuclear Corp., Middletown, PA)

1985-01-01

Estimating the disposal quantity of waste resulting from stabilization of radioactive sludge is complex because of the many factors relating to sample analysis results, radioactive decay, allowable disposal concentrations, and options for disposal containers. To facilitate this estimation, a microcomputer spread sheet template was created. The spread sheet has saved considerable engineering hours. 1 fig., 3 tabs

Preparing for radiological assessments in the event of a tornado strike at Argonne National Lab.-East

International Nuclear Information System (INIS)

Goodkind, M.E.; Klimczak, C.A.; Munyon, W.J.

1993-01-01

Argonne National Laboratory-East (ANL) is a Department of Energy (DOE)-owned, contractor-operated national laboratory located 22 miles southwest of downtown Chicago on a wooded, 1700-acre site. The principal nuclear facilities at ANL include a large fast neutron source (Intense Pulse Neutron Source) in which high-energy protons strike a uranium target to produce neutrons for research studies; 60 Co irradiation sources; chemical and metallurgical plutonium laboratories, some of which are currently being decommissioned; several large hot cell facilities designed for work with multicurie quantities of actinide elements and irradiated reactor fuel materials; a few small research reactors currently in different phases of being decommissioned; and a variety of research laboratories handling many different sources in various chemical and physical forms. The hazards analysis for the ANL site shows that tornado strikes are a serious threat. The site has been struck twice in the past 20 yr, receiving only minor building damage and no release of radioactivity to the environment. Although radioactive materials in general are handled in areas that provide good tornado protection, ANL is prepared to address the problems that would occur should there be a loss of control of radioactive materials due to severe building damage

Array coding for large data memories

Science.gov (United States)

Tranter, W. H.

1982-01-01

It is pointed out that an array code is a convenient method for storing large quantities of data. In a typical application, the array consists of N data words having M symbols in each word. The probability of undetected error is considered, taking into account three symbol error probabilities which are of interest, and a formula for determining the probability of undetected error. Attention is given to the possibility of reading data into the array using a digital communication system with symbol error probability p. Two different schemes are found to be of interest. The conducted analysis of array coding shows that the probability of undetected error is very small even for relatively large arrays.

Preparation and Characterization of Super-paramagnetic Nano-beads for DNA Isolation

Institute of Scientific and Technical Information of China (English)

Xin XIE; Xu ZHANG; Bing Bin YU; wei Yang FE

2004-01-01

Unique coupling reagent, bis-(2-hydroxyethyl methacrylate) phosphate was used to prepare coated and functionalized superparamagnetic nanobeads, leading to a simple, effective method for coating the nanobeads. With this method, the thickness of the coating layer and the functional group contents on the nano-beads could be controlled by changing the quantity of the coated monomers. The nanobeads were characterized by means of transmission electron microscopy (TEM) and Fourier transformation infrared spectroscopy (FTIR). The carboxyl-modified magnetic nano-beads were employed to streamline the protocol of isolation of genomic DNA from the human whole blood.

Evaluating the uncertainty of input quantities in measurement models

Science.gov (United States)

Possolo, Antonio; Elster, Clemens

2014-06-01

The Guide to the Expression of Uncertainty in Measurement (GUM) gives guidance about how values and uncertainties should be assigned to the input quantities that appear in measurement models. This contribution offers a concrete proposal for how that guidance may be updated in light of the advances in the evaluation and expression of measurement uncertainty that were made in the course of the twenty years that have elapsed since the publication of the GUM, and also considering situations that the GUM does not yet contemplate. Our motivation is the ongoing conversation about a new edition of the GUM. While generally we favour a Bayesian approach to uncertainty evaluation, we also recognize the value that other approaches may bring to the problems considered here, and focus on methods for uncertainty evaluation and propagation that are widely applicable, including to cases that the GUM has not yet addressed. In addition to Bayesian methods, we discuss maximum-likelihood estimation, robust statistical methods, and measurement models where values of nominal properties play the same role that input quantities play in traditional models. We illustrate these general-purpose techniques in concrete examples, employing data sets that are realistic but that also are of conveniently small sizes. The supplementary material available online lists the R computer code that we have used to produce these examples (stacks.iop.org/Met/51/3/339/mmedia). Although we strive to stay close to clause 4 of the GUM, which addresses the evaluation of uncertainty for input quantities, we depart from it as we review the classes of measurement models that we believe are generally useful in contemporary measurement science. We also considerably expand and update the treatment that the GUM gives to Type B evaluations of uncertainty: reviewing the state-of-the-art, disciplined approach to the elicitation of expert knowledge, and its encapsulation in probability distributions that are usable in

Semi-preparative scale purification of enterococcal bacteriocin enterocin EJ97, and evaluation of substrates for its production.

Science.gov (United States)

López, Rosario Lucas; García, Ma Teresa; Abriouel, Hikmate; Ben Omar, Nabil; Grande, Ma José; Martínez-Cañamero, Magdalena; Gálvez, Antonio

2007-12-01

The influence of substrate composition on the production of enterocin EJ97 and the conditions for semi-preparative bacteriocin recovery have been studied. Final bacteriocin concentrations of 12.5 or 15.6 mg/l were obtained in the commercial media brain heart infusion broth (BHI) and tryptic soya broth, respectively. The bacteriocin was also produced in the complex medium CM (8.75 mg/l), in which the vitamin supplement was essential for production. Some combinations of meat peptone and yeast extract plus either soy peptone or BHI also supported bacteriocin production, at concentrations of 6.25-7.5 mg/l. In cow milk (whole, half-skimmed, and skimmed), the final bacteriocin concentrations obtained ranged from 7.5 to 11.25 mg/l. Highest bacteriocin activity was obtained by using pasteurised milk whey as growth substrate (up to 25 mg/l), suggesting that this bacteriocin can be obtained on a large scale by using this cheap food-grade industrial by-product. Highest bacteriocin titres were always obtained after 8 h of incubation at 37 degrees C. Semi-preparative concentration and purification of enterocin EJ97 produced in a complex medium was achieved by bulk cation exchange chromatography without previous cell separation, followed by reversed-phase chromatography. This two-step procedure allowed preparation of milligram quantities of purified bacteriocin, which is an improvement compared to purification procedures established for most other bacteriocins (35). The availability of purified enterocin EJ97 will facilitate other studies such as the elucidation of its molecular structure and its interaction with target bacteria.

Prefrontal cortex and sensory cortices during working memory: quantity and quality.

Science.gov (United States)

Ku, Yixuan; Bodner, Mark; Zhou, Yong-Di

2015-04-01

The activity in sensory cortices and the prefrontal cortex (PFC) throughout the delay interval of working memory (WM) tasks reflect two aspects of WM-quality and quantity, respectively. The delay activity in sensory cortices is fine-tuned to sensory information and forms the neural basis of the precision of WM storage, while the delay activity in the PFC appears to represent behavioral goals and filters out irrelevant distractions, forming the neural basis of the quantity of task-relevant information in WM. The PFC and sensory cortices interact through different frequency bands of neuronal oscillation (theta, alpha, and gamma) to fulfill goal-directed behaviors.

BIM IMPLEMENTATION IN A NEW ZEALAND CONSULTING QUANTITY SURVEYING PRACTICE

Directory of Open Access Journals (Sweden)

Curtis Harrison

2015-07-01

Full Text Available 5D BIM – generating cost data via the building information modelling (BIM process- has the potential to be used by quantity surveyors (QSs to streamline their workflows and increase their provision of quality service. Consultant QSs experienced in the use 5D BIM, from the New Zealand office of one large global practice, were interviewed on their perceptions of the benefits of, and barriers to, 5D BIM implementation within their firm. Findings suggest that 5D BIM has numerous benefits over traditional methods, chiefly through the increased efficiency and visualization that BIM provides, along with the rapid identification of design changes. However, realization of these perceived benefits limited to date, due to several barriers hindering 5D BIM implementation: incomplete design and insufficient model object data in the BIM model; a lack of standards to facilitate electronic measurement; legal issues, and a lack of government support. However, participants perceived that 5D BIM implementation will achieve these benefits to a far greater extent in the future. Further research is recommended to identify the BIM skills which QSs will need in the future to reach the full potential of 5D BIM

Efficient acetone sensor based on Ni-doped ZnO nanostructures prepared by spray pyrolysis technique

Science.gov (United States)

Darunkar, Swapnil S.; Acharya, Smita A.

2018-05-01

Ni-doped ZnO thin film was prepared by home-built spray pyrolysis unit for the detection of acetone at 300°C. Scanning electron microscopic (SEM) images of as-developed thin film of undoped ZnO exhibits large quantity of spherical, non-agglomerated particles with uniform size while in Ni-doped ZnO, particles are quite non-uniform in nature. The particle size estimated by using image J are obtained to be around 20-200 nm. Ni-doping effect on band gaps are determined by UV-vis optical spectroscopy and band gap of Ni-doped ZnO is found to be 3.046 eV. Nickel doping exceptionally enhances the sensing response of ZnO as compared to undoped ZnO system. The major role of the Ni-doping is to create more active sites for chemisorbed oxygen on the surface of sensor and correspondingly, to improve the sensing response. The 6 at.% of Ni-doped ZnO exhibits the highest response (92%) for 100 ppm acetone at 300 °C.

An innovative method for the preparation of high API-loaded hollow spherical granules for use in controlled-release formulation.

Science.gov (United States)

Asada, Takumi; Kobiki, Mitsuaki; Ochiai, Yasushi; Iwao, Yasunori; Itai, Shigeru

2017-05-15

The aim of this study was to prepare controlled-release (CR) granules with suitable particle strength, flowability, particle size distribution (PSD) and density characteristics for blending with other excipients. We also wanted these CR granules to contain large quantities of active pharmaceutical ingredient (API). A high shear mixer was used to mix an API with various polymers at various feed ratios, and the resulting granulated materials were sprayed with solvent. The wet granules were dried using a fluidized bed dryer to give CR granules. The API content of the granules was determined to be 95wt%. The granules were found to be spherical in shape with smooth surfaces by scanning electron microscopy. The inner structure of each granule was determined to be hollow by X-ray computed tomography, highlighting the unusual mechanism of this granulation process. The PSD of the granules was found to be dependent on that of the constituent polymer, and a narrow PSD was obtained by adjusting the PSD of the polymer. The dissolution profile of the granules was also dependent on the constituent polymer. Taken together, these results show that we have successfully developed a new manufacturing technology for the simple and low-cost preparation of ideal CR granules. Copyright © 2017 Elsevier B.V. All rights reserved.

Preparation of alumina microspheres

International Nuclear Information System (INIS)

Santos, W.R. dos; Abrao, A.

1980-01-01

Inorganic exchangers are widely used for adsorption and column partition chromatography. The main difficulty of using commercial alumina (in powder) for column chromatography is related to its packing, and the operations through the column become diffcult and time-consuming; also it turns to be virtually impossible to use large dimension columns. In order to eliminate these problems, a process for the preparation of alumina micro-spheres was developed as an adaptation of a similar process used to prepare nuclear fuel microspheres (UO 2 , ThO 2 ). The flowsheet of this process is presented together with the analytical results of sphericity after calcination, granulometry, density and characterization by X-ray diffractometry. Solubility tests showed that the so-prepared microspheres are well resistant to strong acids and bases; retention tests showed their efficiency, mainly to copper. (C.L.B.) [pt

Non-Noether conserved quantity for differential equations of motion in the phase space

Institute of Scientific and Technical Information of China (English)

无

2002-01-01

A non-Noether conserved quantity for the differential equations of motion of mechanical systems in the phase space is studied. The differential equations of motion of the systems are established and the determining equations of Lie symmetry are given. An existence theorem of non-Noether conserved quantity is obtained. An example is given to illustrate the application of the result.

Arrangement for the measurement of the quantity of asphalt in an asphaltic compound

International Nuclear Information System (INIS)

Noma, I.; Taniguchi, K.

1978-01-01

The arrangement for the measurement of the quantity of asphalt in an asphaltic compound in an apparatus for the mixture of asphalt components and an aggregate for the formation of an asphaltic compound characterized by the inclusion of a member for the transmission of a neutron beam which reacts with the hydrogen atoms in the asphaltic compound in such a way that the energy of a neutron beam is adsorbed; a continuous transport device feeds a continuous supply of the asphalt compound past the neutron beam; a member responds to an automatic detector for the quantity of asphaltic components in the asphaltic compound and provides an adjustment so that the quantity [of asphaltic components in asphaltic compound] may be held at a constant value. (G.C.)

Does quantity generate quality? Testing the fundamental principle of brainstorming.

Science.gov (United States)

Muñoz Adánez, Alfredo

2005-11-01

The purpose of this work is to test the chief principle of brainstorming, formulated as "quantity generates quality." The study is included within a broad program whose goal is to detect the strong and weak points of creative techniques. In a sample of 69 groups, containing between 3 and 8 members, the concurrence of two commonly accepted criteria was established as a quality rule: originality and utility or value. The results fully support the quantity-quality relation (r = .893): the more ideas produced to solve a problem, the better quality of the ideas. The importance of this finding, which supports Osborn's theory, is discussed, and the use of brainstorming is recommended to solve the many open problems faced by our society.

Preparative resolution of D,L-threonine catalyzed by immobilized phosphatase.

Science.gov (United States)

Scollar, M P; Sigal, G; Klibanov, A M

1985-03-01

Hydrolysis of L- and D-O-phosphothreonines catalyzed by four different phosphatases, alkaline phosphatases from calf intestine and E. coli and acid phosphatases from wheat germ and potato, has been kinetically studied. Alkaline phosphatases were found to have comparable reactivities towards the optical isomers. On the other hand, both acid phosphatases displayed a marked stereoselectivity, hydrolyzing the L-ester much faster than its D counterpart. Wheat germ acid phosphatase was the most stereoselective enzyme: V(L)/V(D) = 24 and K(m,L)/K(m,D) = 0.17. This enzyme was immobilized (in k-carrageenan gel, followed by crosslinking with glutaraldehyde) and used for the preparative resolution of D,L-threonine: the latter was first chemically O-phosphorylated and then asymmetrically hydrolyzed by the immobilized phosphatase. As a result, gram quantities of L-threonine of high optical purity and O-phospho-D-threonine were prepared. Immobilized wheat germ phosphatase has been tested for the resolution of other racemic alcohols: serine, 2-amino-1-butanol, 1-amino-2-propanol, 2-octanol, and menthol. In all those cases, the enzyme was either not sufficiently stereoselective or too slow for preparative resolutions.

40 CFR 355.12 - What quantities of extremely hazardous substances trigger emergency planning requirements?

Science.gov (United States)

2010-07-01

... EMERGENCY PLANNING AND NOTIFICATION Emergency Planning Who Must Comply § 355.12 What quantities of extremely... 40 Protection of Environment 27 2010-07-01 2010-07-01 false What quantities of extremely hazardous substances trigger emergency planning requirements? 355.12 Section 355.12 Protection of Environment...

Plasma diagnostics on large tokamaks

International Nuclear Information System (INIS)

Orlinskij, D.V.; Magyar, G.

1988-01-01

The main tasks of the large tokamaks which are under construction (T-15 and Tore Supra) and of those which have already been built (TFTR, JET, JT-60 and DIII-D) together with their design features which are relevant to plasma diagnostics are briefly discussed. The structural features and principal characteristics of the diagnostic systems being developed or already being used on these devices are also examined. The different diagnostic methods are described according to the physical quantities to be measured: electric and magnetic diagnostics, measurements of electron density, electron temperature, the ion components of the plasma, radiation loss measurements, spectroscopy of impurities, edge diagnostics and study of plasma stability. The main parameters of the various diagnostic systems used on the six large tokamaks are summarized in tables. (author). 351 refs, 44 figs, 22 tabs

Evaluation of the practical peak voltage quantity for clinical equipment in diagnostic radiology

International Nuclear Information System (INIS)

Pires, Joao dos Santos Justo

2007-01-01

The objective of this work is to evaluate the calculation of the Practical Peak Voltage (PPV) from the voltage waveform and the kerma contrast for two kinds of X-ray equipment: a single phase clinical equipment, a three phase clinical equipment. The PPV from a mammography system voltage waveform will also be established. The development of this work involves intermediate objectives that indicate the quality of the used methods to calculate the PPV. One of these intermediate objectives is the comparison between the invasive calculations of PPV (using a voltage divider) with the response of kVp meter that calculate the PPV. Another intermediate objective is to compare the PPV with the Contrast Equivalent Voltage (the original non-invasive PPV definition). The variation of the PPV with quantities that influence in the voltage waveform like ripple and sample rate will also be contemplated in this work. The results showed that the PPV quantity could be invasive determined trustworthy. Therefore, the ripple quantity is the mainly influence to determinate the PPV that affecting the non-invasive determination. This fact suggest that the non-invasive instruments manufacturers must reevaluate the calculation of the PPV quantity in their instruments. (author)

Mental and Active Preparation: Examining Variations in Women's Processes of Preparing to Leave Abusive Relationships.

Science.gov (United States)

Bermea, Autumn M; Khaw, Lyndal; Hardesty, Jennifer L; Rosenbloom, Lindsay; Salerno, Craig

2017-02-01

Although the process of leaving abusive relationships has received increased research attention, preparing to leave is still largely understudied. Despite an emphasis on safety planning, not all women take active steps to prepare, and the characteristics and experiences of those who do or do not actively prepare are unknown. We address this gap with a secondary data analysis of interviews with 25 abused mothers in the process of leaving. All women initially engaged in mental planning, where they had emotionally disconnected from their partners. Using constructivist grounded theory techniques, we identified two distinct groups: those whose mental planning led to active planning ( n = 11), and those who moved directly from mental planning to leaving ( n = 14) with little time or need to actively plan. The groups differed on several individual, relationship, and child factors, which may have impacted the ability or decisions to prepare. This study supports the feminist view that survivors are not helpless victims but active agents who strategize for safety. Those who engage solely in mental planning still prepare to leave, even if they do not engage in active planning. Practitioners should consider factors affecting preparations and acknowledge mental planning as a necessary effort in leaving.

41 CFR 101-26.507-4 - Quantities in excess of the maximum order limitation.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Quantities in excess of... Management Federal Property Management Regulations System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 26-PROCUREMENT SOURCES AND PROGRAM 26.5-GSA Procurement Programs § 101-26.507-4 Quantities in...

Assessing intake of spices by pattern of spice use, frequency of consumption and portion size of spices consumed from routinely prepared dishes in southern India.

Science.gov (United States)

Siruguri, Vasanthi; Bhat, Ramesh V

2015-01-11

Measurement of dietary intake of spices is gaining significance because of recognition of their health promoting benefits as well as its use for risk assessment of contaminant exposures. Estimating intake of spices at the individual level, presents several challenges since various spices are used as an integrated part of a prepared food and consumed in amounts much smaller than other dietary components. The objective of the present study is to assess intake of spices at the household and individual level on the basis of pattern of spice use and portion size of spice consumed from routinely prepared dishes in Hyderabad city in Southern India. The study was conducted in 100 households in urban areas of Hyderabad city in India with the help of a spice intake questionnaire that was prepared to collect information on the pattern of spice use, frequency, and quantity of spice consumption of 17 spices routinely used in Indian cuisine. The quantity of spice intake was assessed by measuring portion size of spice consumed from the quantity of i) spices added in routinely prepared dishes and ii) the prepared dish consumed by an individual. Based on the type of dish prepared and frequency of preparing the dishes, 11 out of 17 spices were found to be consumed by more than 50% of the households. Maximum number of spices was consumed at weekly frequencies. Red chillies and turmeric were the most frequently consumed spices by 100% of the households. The mean total intake of spices was observed to be higher through dishes consumed daily (10.4 g/portion) than from those consumed at weekly or monthly frequencies. Highest portion size intake was observed for chillies (mean 3.0 g; range 0.05-20.2 g) and lowest for nutmeg (mean 0.14 g; range 0.02-0.64 g) and mace (mean 0.21 g; range: 0.02-0.6 g). The study suggested that assessment of intake of spices varies with frequency of use of spices and type of dish consumed. Portion size estimations of spices consumed and the frequency of

Quantity, Quality, and Satisfaction with Mentoring: What Matters Most?

Science.gov (United States)

Xu, Xiaohong; Payne, Stephanie C.

2014-01-01

According to Kram's mentor role theory, satisfaction with mentoring and mentorship quality are key indicators of effective and successful mentoring. We contribute to mentoring research by demonstrating the relative importance of mentorship quantity, mentorship quality, and satisfaction with mentoring to the prediction of job satisfaction,…

Pharmaceutical quantities of yohimbine found in dietary supplements in the USA.

Science.gov (United States)

Cohen, Pieter A; Wang, Yan-Hong; Maller, Gregory; DeSouza, Renan; Khan, Ikhlas A

2016-01-01

In the USA, botanical dietary supplements are presumed to be safe, but this is not necessarily always the case. Extracts of the evergreen tree yohimbe, Pausinystalia johimbe, though banned in many countries, are sold in hundreds of dietary supplements in the USA. We analyzed 49 brands of supplements labelled as containing yohimbe or yohimbine available for sale from seven major retailers in the USA. Supplements were analyzed using ultra high-performance liquid chromatography coupled to photodiode and quadrupole time-of-flight mass spectrometry detectors for quantity of three alkaloids found in P. johimbe (yohimbine, rauwolscine, and corynanthine). The alkaloids were confirmed on the basis of retention time, ultraviolet spectra, and mass spectra against reference standards. The quantity of the most active alkaloid, yohimbine, per recommended serving ranged from none detected to 12.1 mg. Thirty-nine percent of the supplements (19/49) did not contain rauwolscine and corynanthine suggesting that the yohimbine was either from highly processed plant extract or synthetic in origin. Only 11 supplement brands (22%, 11/49) listed a specific quantity of yohimbine on the label. Most of these were inaccurately labelled (actual content ranged from 23% to 147% of the content on the label). Eighteen percent (9/49) of the supplements' labels did not provide any information about yohimbine's adverse effects. Of the 49 yohimbine supplement brands sold at seven major retail chains in the USA, only 4.1% (2/49) provided consumers with both accurate information about the quantity of yohimbine as well as information about yohimbine's known adverse effects. Copyright © 2015 John Wiley & Sons, Ltd. Copyright © 2015 John Wiley & Sons, Ltd.

Estimation of Waste Quantities Using DeCAT-Pro

Energy Technology Data Exchange (ETDEWEB)

Yun, Taesik; Jung, Hyejin; Oh, Jaeyoung; Kim, Younggook [KHNP CRI, Daejeon (Korea, Republic of)

2016-10-15

The D and D (Dismantling and Decontamination) is scheduled to get started in June 2022 elapsing five years of cooling spent fuels down. The final site status is postulated as Brown Field and tentative DCGL of less than 0.1 mSv per year to evaluate waste quantities in a conservative manner. The decommissioning strategy was determined the immediate decommissioning whose whole period would be taken for approximately 15 years; pre-decommissioning for two years, spent fuel cool-down for five years, D and D for six years, site remediation for two years. The assumption to dismantle the underground facilities including SSCs is to one meter beneath the ground level and the other facilities remain intact. In addition, non-radioactive concrete wastes would be used to landfill gaps of the remaining facilities. Although there are many assumptions we applied, the methodologies developed and the data produced by this research will play a meaningful role as a good starting point for the Kori-1 decommissioning after its shutdown to logically and reasonably estimate the waste quantity. However it is clear that tenacious efforts should be taken to successfully perform the decommissioning project.

Mei Symmetry and New Conserved Quantities of Tzénoff Equations for the Variable Mass Higher-Order Nonholonomic System

Institute of Scientific and Technical Information of China (English)

ZHENG Shi-Wang; WANG Jian-Bo; CHEN Xiang-Wei; XIE Jia-Fang

2012-01-01

Operational systems of spacecraft are general variable mass mechanics systems,and their symmetries and conserved quantities imply profound physical rules of the space system.We study the Mei symmetry of Tzénoff equations for a variable mass nonholonomic system and the new conserved quantities derived.The function expression of the new conserved quantities and the criterion equation which deduces these conserved quantities are presented.This result has some theoretical values in further research of conservation laws obeyed by the variable mass system.%Operational systems of spacecraft are general variable mass mechanics systems, and their symmetries and conserved quantities imply profound physical rules of the space system. We study the Mei symmetry of Tzenoff equations for a variable mass nonholonomic system and the new conserved quantities derived. The function expression of the new conserved quantities and the criterion equation which deduces these conserved quantities are presented. This result has some theoretical values in further research of conservation laws obeyed by the variable mass system.

Gravimetric method for the determination of diclofenac in pharmaceutical preparations.

Science.gov (United States)

Tubino, Matthieu; De Souza, Rafael L

2005-01-01

A gravimetric method for the determination of diclofenac in pharmaceutical preparations was developed. Diclofenac is precipitated from aqueous solution with copper(II) acetate in pH 5.3 (acetic acid/acetate buffer). Sample aliquots had approximately the same quantity of the drug content in tablets (50 mg) or in ampules (75 mg). The observed standard deviation was about +/- 2 mg; therefore, the relative standard deviation (RSD) was approximately 4% for tablet and 3% for ampule preparations. The results were compared with those obtained with the liquid chromatography method recommended in the United States Pharmacopoeia using the statistical Student's t-test. Complete agreement was observed. It is possible to obtain more precise results using higher aliquots, for example 200 mg, in which case the RSD falls to 1%. This gravimetric method, contrary to what is expected for this kind of procedure, is relatively fast and simple to perform. The main advantage is the absolute character of the gravimetric analysis.

131I-m IBG preparation and clinical applications

International Nuclear Information System (INIS)

Yassine, T.; Bakeir, M. A.; Al-Shnan, S.; Al-Asad, M.

2001-12-01

The factors affecting the preparation of 131 I-mIBG were studied and the optimal labelling and preparation conditions were determined in a manner that the requirements of GRP and GMP are satisfied. The m-IBG was labeled by isotopic exchange method where in situ produced Cu (II) was used as a catalyst. The Cu (II) was in situ produced by the effect of thiosulfate on Cu(II) ions in the presence of acetic acid. The optimal conditions were determined as: (The ratio of acetic acid to the iodide-131 solution is 0.5-1.5, the reaction temperature is (160 Centigrade), the reaction period is 60 minutes, and the quantity of m-IBG must be more than 1mg). At these conditions, high labelling yield of 98% was obtained. Further purification lead to an increase in the RCP to more than 99%. All preparations produced sterile and Pyrogen free solutions. The biodistribution studies in rats showed random distribution, which were slightly higher than that were shown in literature. These differences were attributed to the absence of stable iodine saturation of the rats prior to the injection of 131 I-mIBG in this study. Clinical studies using our products showed high localization in the tumors in case of neuroblastoma patients and in adrenal gland in case of pheochromocytoma patients. (author)

DYNAMIC INVESTIGATION OF THE PURCHASE PRICE AND QUANTITY OF MAIZE AND PIG

Directory of Open Access Journals (Sweden)

Judit POÓR

2007-11-01

Full Text Available The aim of our examination was to show the cyclic character in the case of agricultural prices. Beside the investigation of prices the analysis of the purchased quantity is of importance too. We examined the way the prices and quantity exercise mutual influence and the connection between the maize purchase price and the pig purchase price. We compared the Hungarian purchase prices with some international ones, and analyzed the tendencies, the influence of open economies and the approach of the prices.

A note on the expectation and deviation of physical quantities

International Nuclear Information System (INIS)

Nagasawa, Masao

2009-01-01

By using the function representation of self-adjoint operators, the expectation and variance of physical quantities (self-adjoint operators) are defined, and it is shown that the so-called uncertainty principle does not hold.

Efficacy of Indigenous Herbal Preparation on Altered Milk pH, Somatic Cell Count and Electrolyte Profile in Subclinical Mastitis in Cows

Directory of Open Access Journals (Sweden)

A.Y. Kolte

Full Text Available Comparative efficacy of three different locally prepared indigenous herbal paste were evaluated in subclinical 24 mastitic cows with reference to restoring altered milk pH, somatic cell count and milk electrolyte profile. The study revealed that all the treatment were found effective in restoring the altered milk constituents in subclinical mastitis with increased in the milk production. T3 (oots of Withania somnifera (Ashwagandha, Asparagus reacemosus (Shatavari, Curcuma-amada (Ambe Haldi and fresh leaves of Ocimum sanctum (Tulsi in equal quantities was found more effective than T5 ( T3 and T4 in combination in equal quantities and T4 (fresh roots of Glycerrhiza glabra (Jeshathamadh, Nardostachys jatamansi (Jatamansi, leaves of Riccinus communis (Yerand, bark of Ficus racemosa (Umber and rhizome of Curcuma longa (Haldi in equal quantities [Veterinary World 2008; 1(8.000: 239-240

Effects of DME pilot quantity on the performance of a DME PCCI-DI engine

International Nuclear Information System (INIS)

Wang Ying; He Li; Zhou Longbao; Li Wei

2010-01-01

The combination of premixed charge compression ignition and conventional direct-injection compression ignition combustion is studied in a DME engine. This combustion mode is referred to as PCCI-DI combustion. The pilot quantity is found to be one of main variables affecting the PCCI-DI combustion. So, the main objectives of this paper are to examine the effect of different DME pilot quantities on combustion and emission characteristics in a single-cylinder direct-injection DME engine and to determine whether PCCI-DI is a viable in-cylinder NO x emissions reduction technology. In order to evaluate the characteristics of PCCI-DI combustion, the conventional direct-injection compression-ignition engine performance is supplied to make a comparison with their results. Furthermore, special emphasis is put upon the combined combustion process analysis. Results show that DME engine can operate at a wide range of speeds and loads at PCCI-DI mode. In comparison to the conventional DME CI combustion, the brake thermal efficiency slightly increases for DME PCCI-DI operation. PCCI-DI is capable to decrease NO x effectively for all loads. NO x emission shows an obviously descending tendency with an increase in DME pilot quantity at low loads, while it shows a mildly elevating tendency with an increase in DME pilot quantity at high loads. HC and CO emissions increase for DME PCCI-DI operation under various DME pilot quantities.

Quality versus Quantity Debate in Swimming: Perceptions and Training Practices of Expert Swimming Coaches.

Science.gov (United States)

Nugent, Frank J; Comyns, Thomas M; Warrington, Giles D

2017-06-01

The debate over low-volume, high-intensity training versus high-volume, low-intensity training, commonly known as Quality versus Quantity, respectively, is a frequent topic of discussion among swimming coaches and academics. The aim of this study was to explore expert coaches' perceptions of quality and quantity coaching philosophies in competitive swimming and to investigate their current training practices. A purposeful sample of 11 expert swimming coaches was recruited for this study. The study was a mixed methods design and involved each coach participating in 1 semi-structured interview and completing 1 closed-ended questionnaire. The main findings of this study were that coaches felt quality training programmes would lead to short term results for youth swimmers, but were in many cases more appropriate for senior swimmers. The coaches suggested that quantity training programmes built an aerobic base for youth swimmers, promoted technical development through a focus on slower swimming and helped to enhance recovery from training or competition. However, the coaches continuously suggested that quantity training programmes must be performed with good technique and they felt this was a misunderstood element. This study was a critical step towards gaining a richer and broader understanding on the debate over Quality versus Quantity training from an expert swimming coaches' perspective which was not currently available in the research literature.

Quality Versus Quantity Debate in Swimming: Perceptions and Training Practices of Expert Swimming Coaches

Directory of Open Access Journals (Sweden)

Nugent Frank J.

2017-06-01

Full Text Available The debate over low-volume, high-intensity training versus high-volume, low-intensity training, commonly known as Quality versus Quantity, respectively, is a frequent topic of discussion among swimming coaches and academics. The aim of this study was to explore expert coaches’ perceptions of quality and quantity coaching philosophies in competitive swimming and to investigate their current training practices. A purposeful sample of 11 expert swimming coaches was recruited for this study. The study was a mixed methods design and involved each coach participating in 1 semi-structured interview and completing 1 closed-ended questionnaire. The main findings of this study were that coaches felt quality training programmes would lead to short term results for youth swimmers, but were in many cases more appropriate for senior swimmers. The coaches suggested that quantity training programmes built an aerobic base for youth swimmers, promoted technical development through a focus on slower swimming and helped to enhance recovery from training or competition. However, the coaches continuously suggested that quantity training programmes must be performed with good technique and they felt this was a misunderstood element. This study was a critical step towards gaining a richer and broader understanding on the debate over Quality versus Quantity training from an expert swimming coaches’ perspective which was not currently available in the research literature.

Preparation and Purification of Polyclonal Antibodies against Mycobacterium Avium Paratuberculosis Antigens in Rabbit

Directory of Open Access Journals (Sweden)

Hafezeh Alizadeh

2012-12-01

Full Text Available Background and Objective: Johne’s disease is the chronic granulomatous enteritis of ruminants, and a major health hazard worldwide. In recent years, researchers have focused on mycobacterium avium subsp. paratuberculosis (MAP antigens in diagnostic tests. Identification of antibodies against MAP antigens is, therefore, effective for the diagnosis or preparation of vaccine. The aim of this study was to prepare and purify polyclonal antibodies against MAP antigens. Materials and Methods: A New Zealand white rabbit was immunized at a certain time period with MAP antigens and Freund’s adjuvant. After the immunization of the animal, the rabbit was bled to obtain enriched serum. Immunoglobulins were obtained via sedimentation with ammonium sulfate 35% and then IgG was purified by ion exchange (DEAE-cellulose chromatography. Serologic test was used to evaluate the interaction of antigens and antibodies. Results: Ion exchange chromatography of IgG showed one peak, and SDS_PAGE of IgG showed a single band. Serologic test was applied and clear precipitation lines were appeared up to 1:16 dilution, which indicated the high quality of the product. Conclusion: In this study, the humoral immune response was induced well by immunization with MAP antigens in a New Zealand white rabbit and polyclonal antibodies were produced in high titers. Polyclonal antibodies are relatively inexpensive and easy to produce in large quantities and can connect to the more connective sites, resulting in better sensitivity. Identification of polyclonal antibodies via immunological tests can play a significant role in studying MAP disorders.

Role of Leadership in Transforming the Profession of Quantity Surveying

Directory of Open Access Journals (Sweden)

George Ofori

2012-11-01

Full Text Available The construction industry is facing a period of change. The roles ofthe professions involved in the industry in general, and of quantitysurveyors in particular, are also changing. There are opportunitiesfor surveyors to seize the initiative to broaden their involvement inprojects, and attain strategic positions within the industry. However,they will have to improve upon their skill sets and their knowledgebases. Senior quantity surveyors interviewed in Singapore sharedtheir views on the challenges facing the construction industry,and their profession. They suggested that the quantity surveyingprofession would only be able to address the pressing issues itfaces if it pays more attention to innovation and the development ofits people. It should be able to attract and retain talent. Knowledgemanagement will be of critical importance. This will be enabled andfacilitated by knowledge leadership.

A colorimeter for measurement of picomole quantities of urea.

Science.gov (United States)

Vurek, G G; Knepper, M A

1982-04-01

We described a new colorimeter for the measurement of picomole quantities of urea in nanoliter volume fluid samples. The diacetyl monoxime reaction was used to produce a colored product from urea. The method is capable of resolving differences of 10 pmoles between samples containing 0 to 225 pmoles.

19 CFR 151.47 - Optional entry of net quantity of petroleum or petroleum products.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 2 2010-04-01 2010-04-01 false Optional entry of net quantity of petroleum or petroleum products. 151.47 Section 151.47 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF... Petroleum and Petroleum Products § 151.47 Optional entry of net quantity of petroleum or petroleum products...

Solvation quantities from a COSMO-RS equation of state

International Nuclear Information System (INIS)

Panayiotou, C.; Tsivintzelis, I.; Aslanidou, D.; Hatzimanikatis, V.

2015-01-01

Highlights: • Extension of the successful COSMO-RS model to an equation-of-state model. • Two scaling constants, obtained from atom-specific contributions. • Overall estimation of the solvation quantities and contributions. - Abstract: This work focuses on the extension of the successful COSMO-RS model of mixtures into an equation-of-state model of fluids and its application for the estimation of solvation/hydration quantities of a variety of chemical substances. These quantities include free-energies, enthalpies and entropies of hydration as well as the separate contributions to each of them. Emphasis is given on the estimation of contributions from the conformational changes of solutes upon solvation and the associated restructuring of solvent in its immediate neighborhood. COSMO-RS is a quantum-mechanics based group/segment contribution model in which the Quasi-Chemical (QC) approach is used for the description of the non-random distribution of interacting segments in the system. Thus, the equation-of-state development is done through such a QC framework. The new model will not need any adjustable parameters for the strong specific interactions, such as hydrogen bonds, since they will be provided by the quantum-mechanics based cosmo-files – a key feature of COSMO-RS model. It will need, however, one volumetric and one energy parameter per fluid, which are scaling constants or molecular descriptors of the fluid and are obtained from rather easily available data such as densities, boiling points, vapor pressures, heats of vaporization or second virial coefficients. The performance and the potential of the new equation-of-state model to become a fully predictive model are critically discussed

Optimisation of Economic Order Quantity Using Neural Networks Approach = Yapay Sinir Ağları Yaklaşımı ile Ekonomik Düzenin Optimizasyonu

Directory of Open Access Journals (Sweden)

Osman Nuri UÇAN

2001-01-01

Full Text Available In this paper, a Back Propagation-Artificial Neural Network (BP-ANN has been adapted for predicting the required car parts quantities in a real and major auto parts supplier chain. The conventional approach to determine the parts requirements is the Economic Order Quantity (EOQ method. The ability of neural models to learn, particularly their capability of handling large amounts of data simultaneously as well as their fast response time, are the characteristics desired for predictive and forecasting purposes. Here, the actual data obtained from a major auto parts supplier chain, involving a multi-layer system of supplying auto parts to car dealers, have been used to optimise and develop a BP-ANN model. The model has shown promising results in predicting parts orders with high degree of accuracy.

Salt and fat contents in preparations at commercial restaurants in Goiânia-GO

Directory of Open Access Journals (Sweden)

Camila Silva Kunert

2013-08-01

Full Text Available Objective: To evaluate the sodium and fat contents added to preparations of commercialrestaurants in Goiânia-GO, Brazil. Methods: This was an observational, cross-sectionaland descriptive study. It included ‘pay-per-weight’ restaurants with a medium standardmenu and having as daily preparations white rice, beans and grilled chicken. Among theestablishments with these characteristics, three agreed to participate. The production processof the above-mentioned preparations was accompanied for three non-consecutive days ineach establishment. For quantification of sodium and fat added into the preparations, oiland salt were weighed, as well as the finished preparation; the weight of the standard portion and the yield of the preparation expressed in number of portions prepared were settled. From these data, the per capita amount of salt and oil added to cook one portion of each kind of preparation was calculated by dividing the total quantity of salt and oil by the number of prepared portions. Results: The levels of salt (3.0, 2.7, and 4.1 g – restaurant A, B and C,respectively and oil (17.0, 11.3, and 11.2 g – restaurant A, B and C, respectively added inthe three preparations are superior to the recommendations. Conclusion: The sodium andfat contents in the analyzed restaurants are higher than it is recommended by the Food Guidefor the Brazilian Population. It is essential that commercial restaurants become partners ofpublic policies on health promotion, adopting good nutritional practices, by reducing the sodium and fat contents, to offer healthy meals daily.

Preparation of Pillar[5]arene-Based [2]Rotaxanes by a Stopper-Exchange Strategy.

Science.gov (United States)

Nierengarten, Iwona; Meichsner, Eric; Holler, Michel; Pieper, Pauline; Deschenaux, Robert; Delavaux-Nicot, Béatrice; Nierengarten, Jean-François

2018-01-02

A pillar[5]arene-containing rotaxane building block bearing exchangeable stoppers has been prepared in multigram scale quantities with high yields from the reaction of 2,4-dinitrophenol (DNP) with the inclusion complex resulting from the association of dodecanedioyl chloride with 1,4-diethoxypillar[5]arene. Stopper exchange reactions have been achieved by treatment of the resulting DNP diester with various amines through an addition-elimination mechanism preventing the unthreading of the axle component during the reaction and thus preserving the [2]rotaxane structures. The resulting diamide [2]rotaxane derivatives have thus been obtained in good to excellent yields. Importantly, [2]rotaxanes difficult or impossible to prepare by direct introduction of the two stoppers in a single synthetic step are now easily available. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

MICROMICETES QUANTITY AND BIOMASS IN TECHNOGENIC AND NATURAL SOILS

Directory of Open Access Journals (Sweden)

O. N. Korinovskaya

2014-08-01

Full Text Available It is shown that in edaphotopes around of freight checkpoint of CJSC «Krivorozhskiy Surikovyy Zavod», ore-enrichment factory and fresh-inwashed pool of tailings dam of PJSC «Northern Iron Ore Enrichment Works» there is an increase of heavy metals mobile forms (which are the most dangerous for microorganisms, plants, animals and human: for iron in 310; for zinc - in 4,3-6,5; for lead - in 3.2-5.7; for cadmium - in 5,6-9,8; for copper – 6,8-66,5 and for nickel - in 9 times as compared to zonal soil. Whereas in soils of CJSC «Krivorozhskiy Surikovyy Zavod» sanitary protection zone number of copper, nickel, lead, cadmium and zinc mobile forms exceeded the control values in 2,4-6,6 times. For the first time the features of soil microscopic fungi seasonal dynamics of quantity in industrial disturbed soils of Kryvorizhzhya compared to zonal soil (chernozem usual were registered. Changes in fungal mycelium length and biomass, its spore’s amount and biomass in edaphotopes of ore-enrichment and chemical enterprises and of common chernozem are also presented. It is shown that in edaphotopes of heavy contamination areas of «Krivorozhskiy Surikovyy Zavod» and of «Northern Iron Ore Enrichment Works» in spring, summer, and autumn there was decrease of microscopic fungi quantity in 4-10 times, moreover in tehnozems of «Northern Iron Ore Enrichment Works» fresh-inwashed pool of tailings dam their amount reduces in more than 100 times, compared with common chernozem. In low contamination area of «Krivorozhskiy Surikovyy Zavod» their quantity decreases in 2 times. Also in heavy contamination areas of chemical and ore-enrichment enterprises there is strong decrease in the length of fungal mycelium in 2.7-4.2 times, its biomass in 2,6-4,5 times, the spores amount - in 4,5-7,7 times and their biomass - in 10,5-21 times compared to the natural soil, which could be explained by high contents of toxicants. While in the sanitary protection zone of the �

Clarification of the confusion concerning the crystal-field quantities vs the zero-field splitting quantities in magnetism studies: Part II-Survey of literature dealing with model studies of spin systems

International Nuclear Information System (INIS)

Rudowicz, C.

2008-01-01

For respective quantities, i.e., Hamiltonians, parameters, and energy level splittings, related to two physically distinct notions X and Y, various cases of confused terminology have been identified in literature. Referring to a quantity related actually to the notion Y using incorrectly the name of another well-defined notion X constitutes, what may be defined for short as, the type X=Y confusion. An ongoing survey of magnetism literature indicates that quantities related to zero-field splitting (ZFS) or equivalently fine structure (FS) are most often confused with those related to crystal-field (CF) or equivalently ligand field (LF). In this review the CF=ZFS confusion cases, i.e., labelling actual ZFS/FS quantities as purportedly 'CF/LF' ones, appearing in magnetism studies are surveyed and clarified. Part I covers the cases occurring in literature dealing with specific compounds. In this part model studies of spin systems are surveyed. The cases of terminology mixing up actual ZFS/FS quantities with purported CF/LF ones are identified and presented comprehensively in tabular form. To facilitate discussion, problems pertinent for the CF=ZFS confusion are categorized into several groups, including origin of the two notions, physical consequences, usage of specific numerical values, invoking real magnetic spin systems, and properties of spin S=1/2 systems. Physical implications of this confusion for interpretation of model results are also considered. Overall implications of incorrect terminology go beyond simple semantic issues and concern possible misinterpretation of data describing various physical properties of models studied. Such terminology contributes also to misleading keyword classifications of papers in journals and scientific databases. Other types of confusion identified in survey of magnetism literature will be discussed in separate reviews

Is the Quantity Theory of Money Useful in Forecasting U.S. Inflation?

DEFF Research Database (Denmark)

Lanne, Markku; Luoto, Jani; Nyberg, Henri

We propose a new simple model incorporating the implication of the quantity theory of money that money growth and ináation should move one for one in the long run, and, hence, ináation should be predictable by money growth. The model Öts postwar U.S. data well, and beats common univariate benchma...... models in forecasting ináation. Moreover, this evidence is quite robust, and predictability is found also in the Great moderation period. The detected predictability of ináation by money growth lends support to the quantity theory....

Teacher quality and quantity as correlates of secondary school ...

African Journals Online (AJOL)

This study investigated the twin variables of quality and quantity of teachers as correlates of secondary school academic performance in Ogun State of Nigeria between 1997/98 and 2000/2001 academic sessions. The study was conducted ex-post facto under a descriptive survey research design using the proportional to ...

Water quantity and quality at the urban-rural interface

Science.gov (United States)

Ge Sun; B. Graeme Lockaby

2012-01-01

Population growth and urban development dramatically alter natural watershed ecosystem structure and functions and stress water resources. We review studies on the impacts of urbanization on hydrologic and biogeochemical processes underlying stream water quantity and water quality issues, as well as water supply challenges in an urban environment. We conclude that...

Resource rents: The effects of energy taxes and quantity instruments for climate protection

International Nuclear Information System (INIS)

Eisenack, Klaus; Edenhofer, Ottmar; Kalkuhl, Matthias

2012-01-01

Carbon dioxide emissions correspond to fossil resource use. When considering this supply side of climate protection, crucial questions come to fore. It seems likely that owners of fossil resources would object to emission reductions. Moreover, policy instruments such as taxes may not be effective at all: it seems individually rational to leave no fossil resources unused. In this context, it can be expected that economic sectors will react strategically to climate policy, aiming at a re-distribution of rents. To address these questions, we investigate the effectiveness, efficiency, and resource rents for energy taxes, resource taxes, and quantity rationing of emissions. The analysis is based on a game theoretic growth model with explicit factor markets and policy instruments. Market equilibrium depends on a government that acts as a Stackelberg leader with a climate protection goal. We find that resource taxes and quantity rationing achieve this objective efficiently, energy taxation is only second-best. The use of quantity rationing to achieve climate protection generates substantial rents for resource owners. - Highlights: ► Resource taxes and quantity rationing (carbon budgets) are efficient. ► Carbon budgets increase resource rents, while taxes decrease rents. ► Resource owners may support climate protection. ► Climate protection introduces a climate rent.

Supply Chain Coordination under Trade Credit and Quantity Discount with Sales Effort Effects

Directory of Open Access Journals (Sweden)

Zhihong Wang

2018-01-01

Full Text Available The purpose of this paper is to investigate the role of trade credit and quantity discount in supply chain coordination when the sales effort effect on market demand is considered. In this paper, we consider a two-echelon supply chain consisting of a single retailer ordering a single product from a single manufacturer. Market demand is stochastic and is influenced by retailer sales effort. We formulate an analytical model based on a single trade credit and find that the single trade credit cannot achieve the perfect coordination of the supply chain. Then, we develop a hybrid quantitative analytical model for supply chain coordination by coherently integrating incentives of trade credit and quantity discount with sales effort effects. The results demonstrate that, providing that the discount rate satisfies certain conditions, the proposed hybrid model combining trade credit and quantity discount will be able to effectively coordinate the supply chain by motivating retailers to exert their sales effort and increase product order quantity. Furthermore, the hybrid quantitative analytical model can provide great flexibility in coordinating the supply chain to achieve an optimal situation through the adjustment of relevant parameters to resolve conflict of interests from different supply chain members. Numerical examples are provided to demonstrate the effectiveness of the hybrid model.

Electrodeposition as an alternate method for preparation of environmental samples for iodide by AMS

Energy Technology Data Exchange (ETDEWEB)

Adamic, M.L., E-mail: Mary.Adamic@inl.gov [Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83402 (United States); Lister, T.E.; Dufek, E.J.; Jenson, D.D.; Olson, J.E. [Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83402 (United States); Vockenhuber, C. [Laboratory of Ion Beam Physics, ETH Zurich, Otto-Stern-Weg 5, 8093 Zurich (Switzerland); Watrous, M.G. [Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83402 (United States)

2015-10-15

This paper presents an evaluation of an alternate method for preparing environmental samples for {sup 129}I analysis by accelerator mass spectrometry (AMS) at Idaho National Laboratory. The optimal sample preparation method is characterized by ease of preparation, capability of processing very small quantities of iodide, and ease of loading into a cathode. Electrodeposition of iodide on a silver wire was evaluated using these criteria. This study indicates that the electrochemically-formed silver iodide deposits produce ion currents similar to those from precipitated silver iodide for the same sample mass. Precipitated silver iodide samples are usually mixed with niobium or silver powder prior to loading in a cathode. Using electrodeposition, the silver is already mixed with the sample and can simply be picked up with tweezers, placed in the sample die, and pressed into a cathode. The major advantage of this method is that the silver wire/electrodeposited silver iodide is much easier to load into a cathode.

Electrodeposition as an alternate method for preparation of environmental samples for iodide by AMS

International Nuclear Information System (INIS)

Adamic, M.L.; Lister, T.E.; Dufek, E.J.; Jenson, D.D.; Olson, J.E.; Vockenhuber, C.; Watrous, M.G.

2015-01-01

This paper presents an evaluation of an alternate method for preparing environmental samples for "1"2"9I analysis by accelerator mass spectrometry (AMS) at Idaho National Laboratory. The optimal sample preparation method is characterized by ease of preparation, capability of processing very small quantities of iodide, and ease of loading into a cathode. Electrodeposition of iodide on a silver wire was evaluated using these criteria. This study indicates that the electrochemically-formed silver iodide deposits produce ion currents similar to those from precipitated silver iodide for the same sample mass. Precipitated silver iodide samples are usually mixed with niobium or silver powder prior to loading in a cathode. Using electrodeposition, the silver is already mixed with the sample and can simply be picked up with tweezers, placed in the sample die, and pressed into a cathode. The major advantage of this method is that the silver wire/electrodeposited silver iodide is much easier to load into a cathode.

Disaster preparation in kidney transplant recipients: a questionnaire-based cohort study from a large United States transplant center
.

Science.gov (United States)

Sharief, Shimi; Freitas, Daniel; Adey, Deborah; Wiley, James

2018-04-01

Few quantitative assessments have assessed disaster preparation in kidney transplant patients. This is a survey-based assessment of disaster preparedness of 200 patients at the University of California San Francisco, USA. Patients answered questionnaires assessing their level of preparedness as well as barriers to preparation. Preparedness was scored based on response to 7 questions. Univariate analyses compared participant characteristics extracted from the medical chart against three tertiles of preparedness: low (scores 0 - 2), medium (scores 3 - 4), and high (scores 5 - 7). California counties were coded and mapped by average preparedness scores. Only 30% of patients were highly prepared for disasters. Participants were prepared with available medication for 2 weeks (78.5%) and least prepared in having a medical ID bracelet (13%). Significant minorities of patients (40% of patients or more) were unprepared with lists of medications, important phone numbers and disaster kits. Preparedness was not associated with demographic and clinical characteristics. Monterey County was the most prepared of the 31 California counties sampled (score of 4.25 out of 7). All patients should be educated regarding disaster preparation. County and medical services should collaborate to address specialized populations in general preparedness planning.
.

Thermodynamic quantities for the Klein–Gordon equation with a ...

Indian Academy of Sciences (India)

2017-02-01

Feb 1, 2017 ... Abstract. We study some thermodynamic quantities for the Klein–Gordon equation with a linear plus inverse- linear, scalar potential. We obtain the energy eigenvalues with the help of the quantization rule from the biconfluent Heun's equation. We use a method based on the Euler–MacLaurin formula to ...

Preparation and use of viscous-elastic clay-polymer mixtures in drilling

Energy Technology Data Exchange (ETDEWEB)

Davydov, V K; Tyurin, I P

1979-01-01

A highly viscous-elastic mixture (VUS) has been widely used as a buffer liquid. It consists of a weakly concentrated aqueous polyacrylamide solute with additives of small quantities of an aqueous hexaresorcin tar and formalin solution. Laboratory tests have shown that when this mixture is prepared, a bentonite suspension is required with a pH 7, containing minimum 10% solid phase and an aqueous polyacrylamide solution with concentration of no less than 1%. Tests have shown that the effect of this formula varies according to proportions in the mixture. Temperature and selection of the formula must be made on an individual basis.

Overview of Site Preparation

International Nuclear Information System (INIS)

Garin, P.

2006-01-01

The preparation of Cadarache as the host of ITER is organised at a double level: Europe, since the beginning of the candidature in 2001, is coordinating the so-called European ITER Site Studies; France, as the host country, has put in place a dedicated structure at a decisional level (close to the government), and operational level in the PACA region with two entities: The Agency Iter France (AIF), inside the CEA, interlocutor of international and European entities, in charge of site preparation and fund recollection; An accompanying prefectoral mission, in charge mainly of road adaptation and the international school. The paper will cover all the aspects related to the preparation of the implementation of ITER: Technical aspects: the progress of site preparation itself, its servicing (water supply, electrical supply, Internet...), the road adaptation between the large harbour of Fos-sur-mer and Cadarache, etc. will be detailed. Regulatory procedures: in the framework of the delegation that the ITER partners gave to the CEA/AIF on 14 th September 2005, two main large files are in progress: The public debate, organised by an independent authority, informs the population of the challenges and impacts of ITER in Provence; The safety documents: the writing of the preliminary safety report, which will be submitted to the Nuclear Safety Authority and the files submitted to the public during the public enquiries are ongoing. Socioeconomic aspects: the welcome of ITER staff and their families is operational, via a dedicated Welcome Office; the location of an international school in Manosque leads now to its pre-figuration. The overall organisation will be described, as well as all planning forecast for the coming years, leading to the start of construction. (author)

All-In-One: Advanced preparation of Human Parenchymal and Non-Parenchymal Liver Cells.

Directory of Open Access Journals (Sweden)

Melanie Werner

Full Text Available Liver cells are key players in innate immunity. Thus, studying primary isolated liver cells is necessary for determining their role in liver physiology and pathophysiology. In particular, the quantity and quality of isolated cells are crucial to their function. Our aim was to isolate a large quantity of high-quality human parenchymal and non-parenchymal cells from a single liver specimen.Hepatocytes, Kupffer cells, liver sinusoidal endothelial cells, and stellate cells were isolated from liver tissues by collagenase perfusion in combination with low-speed centrifugation, density gradient centrifugation, and magnetic-activated cell sorting. The purity and functionality of cultured cell populations were controlled by determining their morphology, discriminative cell marker expression, and functional activity.Cell preparation yielded the following cell counts per gram of liver tissue: 2.0 ± 0.4 × 10(7 hepatocytes, 1.8 ± 0.5 × 10(6 Kupffer cells, 4.3 ± 1.9 × 10(5 liver sinusoidal endothelial cells, and 3.2 ± 0.5 × 10(5 stellate cells. Hepatocytes were identified by albumin (95.5 ± 1.7% and exhibited time-dependent activity of cytochrome P450 enzymes. Kupffer cells expressed CD68 (94.5 ± 1.2% and exhibited phagocytic activity, as determined with 1 μm latex beads. Endothelial cells were CD146(+ (97.8 ± 1.1% and exhibited efficient uptake of acetylated low-density lipoprotein. Hepatic stellate cells were identified by the expression of α-smooth muscle actin (97.1 ± 1.5%. These cells further exhibited retinol (vitamin A-mediated autofluorescence.Our isolation procedure for primary parenchymal and non-parenchymal liver cells resulted in cell populations of high purity and quality, with retained physiological functionality in vitro. Thus, this system may provide a valuable tool for determining liver function and disease.

Review on evolvement of systems of ionizing radiation quantities and units

International Nuclear Information System (INIS)

Zheng Junzheng; Zeng Zhi

2009-01-01

To scientifically and practically measure the ionizing radiation in unison is an indispensable prerequisite and foundation for the extensive uses of nuclear science and technology, development of radiological protection and safety standards, as well as prevention and treatment of ionizing radiation hazards. Concerning about the quantities and units of ionizing radiation as well as their corresponding measurement and application methods, relevant international organizations and all countries in the world generally adopt the systems proposed by the International Commission on Radiation Units and Measurements (ICRU) which is a well recognized and authoritative academic organization.In the paper,the major evolutions of the systems for ionizing radiation quantities and units in the past decades are summarized. (authors)

On the operational quantity Hp(3) for eye lens dosimetry

International Nuclear Information System (INIS)

Behrens, R

2012-01-01

In the past the operational quantity H p (3) has been defined for calibration purposes in a slab phantom. Recently, an additional phantom in the form of a cylinder was suggested for eye lens dosimetry as a cylinder much better approximates the shape of a head than a slab. Therefore, this work investigates whether the quantity H p (3), when defined in the respective calibration phantom, adequately estimates the eye lens dose (or is at least conservative) depending on the phantom: it turns out that in most cases both calibration phantoms are similarly well suited. Finally, the definition of the eye lens dose is discussed together with possible consequences on the definition of H p (3): the consideration of only the radiation sensitive volume of the lens causes H p (3) not to be conservative in beta radiation fields. (paper)

Polymorphism of a polymer precursor: metastable glycolide polymorph recovered via large scale high-pressure experiments

DEFF Research Database (Denmark)

Hutchison, Ian B.; Delori, Amit; Wang, Xiao

2015-01-01

Using a large volume high-pressure press a new polymorph of an important precursor for biomedical polymers was isolated in gram quantities and used to seed crystallisation experiments at ambient pressure....

Gelatin/chitosan biofilm: preparation and characterization

International Nuclear Information System (INIS)

Trindade, Luciane da C.; Nunes, Raquel A.; Diniz, Nadie K.S.; Braga, Carla R.C.; Silva, Suedina M. de Lima

2011-01-01

In this study, gelatin, chitosan and gelatin/chitosan bio films using the ratio of gelatin/chitosan (50/50) were prepared by casting method. The bio films prepared were characterized by X-ray diffraction, scanning electron microscopy and dissolution ratio. According to the results, the incorporation of chitosan into gelatin indicate the decrease of crystallinity of chitosan, a compact structure without large pores and that the dissolution of gelatin/chitosan film is little influenced by hot water than gelatin films. (author)

Use of large-scale chromatography in the preparation of armodafinil.

Science.gov (United States)

Hauck, Willy; Adam, Philippe; Bobier, Christelle; Landmesser, Nelson

2008-08-01

Armodafinil, the (R)-enantiomer of modafinil, is a medication used to treat the excessive sleepiness associated with narcolepsy, obstructive sleep apnea/hypopnea syndrome, and shift work sleep disorder. We report here the chemical development of armodafinil and the investigations that led to a commercial route to prepare this pure enantiomer. Three synthetic approaches were used to provide the chiral sulfoxide. Resolution via preferential crystallization was used for phase I clinical trials and was subsequently replaced by chiral chromatography, enabling us to pursue a rapid filing and registration of the API. Finally, the commercial route was developed and employed asymmetric oxidation catalyzed by a titanium(IV) isopropoxide and diethyl tartrate system. The advantages of choosing a chromatographic development pathway to expedite registration while concurrently developing an economical chiral synthesis route is discussed in the context of armodafinil development. (c) 2008 Wiley-Liss, Inc.

Interlayer catalytic exfoliation realizing scalable production of large-size pristine few-layer graphene

OpenAIRE

Geng, Xiumei; Guo, Yufen; Li, Dongfang; Li, Weiwei; Zhu, Chao; Wei, Xiangfei; Chen, Mingliang; Gao, Song; Qiu, Shengqiang; Gong, Youpin; Wu, Liqiong; Long, Mingsheng; Sun, Mengtao; Pan, Gebo; Liu, Liwei

2013-01-01

Mass production of reduced graphene oxide and graphene nanoplatelets has recently been achieved. However, a great challenge still remains in realizing large-quantity and high-quality production of large-size thin few-layer graphene (FLG). Here, we create a novel route to solve the issue by employing one-time-only interlayer catalytic exfoliation (ICE) of salt-intercalated graphite. The typical FLG with a large lateral size of tens of microns and a thickness less than 2?nm have been obtained b...

Buyer-vendor coordination for fixed lifetime product with quantity discount under finite production rate

Science.gov (United States)

Zhang, Qinghong; Luo, Jianwen; Duan, Yongrui

2016-03-01

Buyer-vendor coordination has been widely addressed; however, the fixed lifetime of the product is seldom considered. In this paper, we study the coordination of an integrated production-inventory system with quantity discount for a fixed lifetime product under finite production rate and deterministic demand. We first derive the buyer's ordering policy and the vendor's production batch size in decentralised and centralised systems. We then compare the two systems and show the non-coordination of the ordering policies and the production batch sizes. To improve the supply chain efficiency, we propose quantity discount contract and prove that the contract can coordinate the buyer-vendor supply chain. Finally, we present analytically tractable solutions and give a numerical example to illustrate the benefits of the proposed quantity discount strategy.

Analysis on Domestic Law and Management Trend Related to Small-Quantity Nuclear Material

International Nuclear Information System (INIS)

Park, Jae Beom; Lee, Kyong Woo; Shim, Hye Won; Min, Gyung Sik

2005-01-01

International Atomic Energy Agency (IAEA) has requested Korea to establish and manage the law ruling all nuclear materials through the INFCIRC/153. Now, it has been 30 years since Korea made the agreement, INFCIRC/153, with IAEA. Korea has tried their best to accomplish the international standard in nuclear control field and it is a fact that Korea finally produced some results in the nuclear control field. Related to nuclear material control, Korea is above the common level appropriately ranked 6th in the world in terms of nuclear power. Before 2000, Korea was making the foundation secure in the nuclear control. IAEA did not urge to establish the law supervising the small-quantity nuclear material and depleted uranium (DU). In a turnaround from early IAEA moderate line to Korea, the situation was changed. Since IAEA brought up the agenda to 2000 Joint Review Meeting between Korea-IAEA, IAEA has asked Korea to establish the control system for smallquantity nuclear material and DU. In 2003, the Korean government set up a project establishing the control system about all nuclear material including small-quantity nuclear material and DU. National Nuclear Management and Control Agency (NNCA), delegating the business relating to international controlling materials from government, developed some modules in nuclear material control system and operated it. The system includes a controlling system for small-quantity nuclear material. NNCA on behalf of government has collected the information and Korea Ministry of Science and Technology (MOST) has reported the information to the IAEA. This paper introduces you the background of controlling the small-quantity nuclear material and the system of controlling nuclear material in Korea. And it will suggest the improvement of the management method in the system for small-quantity nuclear material

Analysis on Domestic Law and Management Trend Related to Small-Quantity Nuclear Material

Energy Technology Data Exchange (ETDEWEB)

Park, Jae Beom; Lee, Kyong Woo; Shim, Hye Won; Min, Gyung Sik [National Nuclear Management and Control Agency, Daejeon (Korea, Republic of)

2005-07-01

International Atomic Energy Agency (IAEA) has requested Korea to establish and manage the law ruling all nuclear materials through the INFCIRC/153. Now, it has been 30 years since Korea made the agreement, INFCIRC/153, with IAEA. Korea has tried their best to accomplish the international standard in nuclear control field and it is a fact that Korea finally produced some results in the nuclear control field. Related to nuclear material control, Korea is above the common level appropriately ranked 6th in the world in terms of nuclear power. Before 2000, Korea was making the foundation secure in the nuclear control. IAEA did not urge to establish the law supervising the small-quantity nuclear material and depleted uranium (DU). In a turnaround from early IAEA moderate line to Korea, the situation was changed. Since IAEA brought up the agenda to 2000 Joint Review Meeting between Korea-IAEA, IAEA has asked Korea to establish the control system for smallquantity nuclear material and DU. In 2003, the Korean government set up a project establishing the control system about all nuclear material including small-quantity nuclear material and DU. National Nuclear Management and Control Agency (NNCA), delegating the business relating to international controlling materials from government, developed some modules in nuclear material control system and operated it. The system includes a controlling system for small-quantity nuclear material. NNCA on behalf of government has collected the information and Korea Ministry of Science and Technology (MOST) has reported the information to the IAEA. This paper introduces you the background of controlling the small-quantity nuclear material and the system of controlling nuclear material in Korea. And it will suggest the improvement of the management method in the system for small-quantity nuclear material.

Highway route controlled quantity shipment routing reports - An overview

International Nuclear Information System (INIS)

Cashwell, J.W.; Welles, B.W.; Welch, M.J.

1989-01-01

US Department of Transportation (DOT) regulations require a postnotification report from the shipper for all shipments of radioactive materials categorized as a Highway Route Controlled Quantity. These postnotification reports, filed in compliance with 49 CFR 172.203(d), have been compiled by the DOT in a database known as the Radioactive Materials Routing Report (RAMRT) since 1982. The data were sorted by each of its elements to establish historical records and trends of Highway Route Controlled Quantity shipments from 1982 through 1987. Approximately 1520 records in the RAMRT database were compiled for this analysis. Approximately half of the shipments reported for the study period were from the US Department of Energy (DOE) and its contractors, with the others being commercial movements. Two DOE installations, EG and G Idaho and Oak Ridge, accounted for nearly half of the DOE activities. Similarly, almost half of the commercial movements were reported by two vendors, Nuclear Assurance Corporation and Transnuclear, Incorporated. Spent fuel from power and research reactors accounted for approximately half of all shipments

Quantity and biochemical composition of particulate organic matter in a highly trawled area (Thermaikos Gulf, Eastern Mediterranean Sea

Directory of Open Access Journals (Sweden)

Antonio Pusceddu

2015-11-01

Full Text Available Bottom trawling represents nowadays one of the most severe anthropogenic disturbances at sea, and determines large impacts on benthic communities and processes. Bottom trawling determines also local sediment resuspension and the effects of the injection of large amounts of surface sediments into the water column have been repeatedly investigated. Few studies have assessed the consequences of sediment resuspension caused by bottom trawling on the quantity, biochemical composition and bioavailability of suspended organic particles and how these eventually rival those exerted by natural storms. To provide insights on this poorly addressed issue, we investigated concentrations and biochemical composition of total and enzymatically digestible pools of particulate organic matter (POM in the Thermaikos Gulf (Mediterranean Sea under calm sea conditions, during intensive trawling activities, and after a severe storm. We show here that sediment resuspension caused by trawling can cause large effects on POM quantity, biochemical composition and bioavailability. Both during trawling and after the storm, the relative importance of the carbohydrate pools increased (in the upper water column and the total lipid concentrations decreased (in the intermediate and bottom layers when compared to values measured during calm conditions. These results would suggest that bottom trawling could inject in the upper water column POM pools more refractory in nature (e.g., carbohydrates than those present in calm or after-storm conditions. By contrast, we show also that the bioavailable fraction of biopolymeric C increased significantly during trawling in the upper water column of the shallowest stations and in the bottom water column layer of the deepest ones. These results provide evidence that bottom trawling can influence the overall trophic status of coastal waters, exerting effects similar or stronger than those caused by natural storms, though of variable amplitude

Preparing diagnostic data for the SNAP transport code

International Nuclear Information System (INIS)

Murphy, J.A.; Scott, S.D.; Towner, H.H.

1992-01-01

This paper describes the program SNAPIN which is used to prepare data for transport analysis with the SNAP code. The data input to SNAP includes diagnostic profiles [n e (R), T e (R), T i (R), v φ (R), Z eff (R), P rad (R)] and measurements such as total plasma current, R major , beam power, gas puff rate, etc. SNAPIN reads in the necessary TFTR data, allows editing of that data, including graphical editing of profile data and the selection of physics models. SNAPIN allows comparison of profile data from all diagnostics that measure a quantity, for example, electron temperature profiles from Thomson scattering and electron cyclotron emission (ECE). A powerful user interface is important to help the user prepare input data sets quickly and consistently, because hundreds of variables must be specified for each analysis. SNAPIN facilitates this by a careful organization of menus, display of all scalar data and switch settings within the menus, the graphical editing and comparison of profiles, and step-by-step checking for consistent physics controls [J. Murphy, S. Scott, and H. Towner, The SNAP User's Guide, Technical Report PPPL-TM-393, Princeton Plasma Physics Laboratory (1992)

Preparative radiation chemistry

International Nuclear Information System (INIS)

Drawe, H.

1978-01-01

Preparative synthesis of compounds with the aid of radiation chemistry is increasingly used in laboratories as well as on a technical scale. A large number of new compounds has been produced with the methods of radiation chemistry. With the increasing number of available radiation sources, also the number of synthesis metods in radiation chemistry has increased. This paper can only briefly mention the many possible ways of synthesis in radiation chemistry. (orig./HK) [de

Cytological preparations for molecular analysis: A review of technical procedures, advantages and limitations for referring samples for testing.

Science.gov (United States)

da Cunha Santos, G; Saieg, M A; Troncone, G; Zeppa, P

2018-04-01

Minimally invasive procedures such as endobronchial ultrasound-guided transbronchial needle aspiration (EBUS-TBNA) must yield not only good quality and quantity of material for morphological assessment, but also an adequate sample for analysis of molecular markers to guide patients to appropriate targeted therapies. In this context, cytopathologists worldwide should be familiar with minimum requirements for refereeing cytological samples for testing. The present manuscript is a review with comprehensive description of the content of the workshop entitled Cytological preparations for molecular analysis: pre-analytical issues for EBUS TBNA, presented at the 40th European Congress of Cytopathology in Liverpool, UK. The present review emphasises the advantages and limitations of different types of cytology substrates used for molecular analysis such as archival smears, liquid-based preparations, archival cytospin preparations and FTA (Flinders Technology Associates) cards, as well as their technical requirements/features. These various types of cytological specimens can be successfully used for an extensive array of molecular studies, but the quality and quantity of extracted nucleic acids rely directly on adequate pre-analytical assessment of those samples. In this setting, cytopathologists must not only be familiar with the different types of specimens and associated technical procedures, but also correctly handle the material provided by minimally invasive procedures, ensuring that there is sufficient amount of material for a precise diagnosis and correct management of the patient through personalised care. © 2018 John Wiley & Sons Ltd.

Dimensions of Organisational Culture in Quantity Surveying Firms in Nigeria

Directory of Open Access Journals (Sweden)

Ayokunle Olubunmi Olanipekun

2014-12-01

Full Text Available The functionalist paradigm of organisational culture (OC views culture as a variable subject to conscious manipulation and control in order to solve organisational challenges. Therefore, this paper provides information on how OC is a solution to the challenges in Quantity Surveying firms (QSFs.  This was achieved by eliciting the dimensions of OC in forty two QSFs in Lagos, Nigeria, which are the business, people and external environment dimensions. The paper concludes that OC is a relevant solution to the identity and management related challenges in QSFs. Specifically, the paper informs on the implications of business and people dimensions of OC as a solution to the identity challenges, as well as on the implication of the external environment dimension of OC to the management challenges. Based on the findings, practical implications and recommendations were directed at the management and employees QSs in QSFs and Quantity Surveying researchers.

Large Eddy Simulation of stratified flows over structures

OpenAIRE

Brechler J.; Fuka V.

2013-01-01

We tested the ability of the LES model CLMM (Charles University Large-Eddy Microscale Model) to model the stratified flow around three dimensional hills. We compared the quantities, as the height of the dividing streamline, recirculation zone length or length of the lee waves with experiments by Hunt and Snyder[3] and numerical computations by Ding, Calhoun and Street[5]. The results mostly agreed with the references, but some important differences are present.

Large Eddy Simulation of stratified flows over structures

Science.gov (United States)

Fuka, V.; Brechler, J.

2013-04-01

We tested the ability of the LES model CLMM (Charles University Large-Eddy Microscale Model) to model the stratified flow around three dimensional hills. We compared the quantities, as the height of the dividing streamline, recirculation zone length or length of the lee waves with experiments by Hunt and Snyder[3] and numerical computations by Ding, Calhoun and Street[5]. The results mostly agreed with the references, but some important differences are present.

Salt and fat contents in preparations at commercial restaurants in Goiânia-GO

Directory of Open Access Journals (Sweden)

Camila Silva Kunert

2013-03-01

Full Text Available Objective: To evaluate the sodium and fat contents added to preparations of commercial restaurants in Goiânia-GO, Brazil. Methods: This was an observational, cross-sectional and descriptive study. It included ‘pay-per-weight’ restaurants with a medium standard menu and having as daily preparations white rice, beans and grilled chicken. Among the establishments with these characteristics, three agreed to participate. The production process of the above-mentioned preparations was accompanied for three non-consecutive days in each establishment. For quantification of sodium and fat added into the preparations, oil and salt were weighed, as well as the finished preparation; the weight of the standard portion and the yield of the preparation expressed in number of portions prepared were settled. From these data, the per capita amount of salt and oil added to cook one portion of each kind of preparation was calculated by dividing the total quantity of salt and oil by the number of prepared portions. Results: The levels of salt (3.0, 2.7, and 4.1 g – restaurant A, B and C, respectively and oil (17.0, 11.3, and 11.2 g – restaurant A, B and C, respectively added in the three preparations are superior to the recommendations. Conclusion: The sodium and fat contents in the analyzed restaurants are higher than it is recommended by the Food Guide for the Brazilian Population. It is essential that commercial restaurants become partners of public policies on health promotion, adopting good nutritional practices, by reducing the sodium and fat contents, to offer healthy meals daily.

Lost but can't be neglected: Huge quantities of small microplastics hide in the South China Sea.

Science.gov (United States)

Cai, Minggang; He, Haixia; Liu, Mengyang; Li, Siwei; Tang, Guowen; Wang, Weimin; Huang, Peng; Wei, Ge; Lin, Yan; Chen, Bin; Hu, Jiahui; Cen, Zhengnan

2018-08-15

Large quantities of microplastics with small particle sizes were found in the South China Sea (SCS). The abundances of microplastics in seawater were 0.045±0.093and 2569±1770particles/m 3 according to the bongo net and pumping sampling methods, respectively. Smaller-size fractions (sizeseas with ocean currents. The distribution characteristics showed that it was mainly controlled by terrestrial input of the Pearl River. This study, as the first report from SCS on microplastics in water for its distribution and influence factors, provided impetus for further research on the transportation fate and the behavior of this emerging pollutant from coastal zone to the open oceans. Copyright © 2018 Elsevier B.V. All rights reserved.

One-carbon 13C-labeled synthetic intermediates. Comparison and evaluation of preparative methods

International Nuclear Information System (INIS)

Ott, D.G.

1978-01-01

Frequently the biggest stumbling block to the synthesis of a structurally complex labeled compound is obtaining the required low molecular weight, structurally simple, isotopic intermediates. Selection of a particular scheme from various alternatives depends on the available capabilities and quantity of product desired, as well as on anticipated future requirements and need for related compounds. Many of the newer reagents for organic synthesis can be applied effectively to isotopic preparations with improvements of yields and simplification of procedures compared to established classical methods. New routes developed for higher molecular weight compounds are sometimes not directly adaptable to the one-carbon analogs, either because of isolation difficulties occasioned by physical properties or by chemical reactivities peculiar to their being first members of homologous series. Various routes for preparation of carbon-13 labeled methanol, formaldehyde, and cyanide are compared

[Estimation of maximum acceptable concentration of lead and cadmium in plants and their medicinal preparations].

Science.gov (United States)

Zitkevicius, Virgilijus; Savickiene, Nijole; Abdrachmanovas, Olegas; Ryselis, Stanislovas; Masteiková, Rūta; Chalupova, Zuzana; Dagilyte, Audrone; Baranauskas, Algirdas

2003-01-01

Heavy metals (lead, cadmium) are possible dashes which quantity is defined by the limiting acceptable contents. Different drugs preparations: infusions, decoctions, tinctures, extracts, etc. are produced using medicinal plants. The objective of this research was to study the impurities of heavy metals (lead, cadmium) in medicinal plants and some drug preparations. We investigated liquid extracts of fruits Crataegus monogyna Jacq. and herbs of Echinacea purpurea Moench., tinctures--of herbs Leonurus cardiaca L. The raw materials were imported from Poland. Investigations were carried out in cooperation with the Laboratory of Antropogenic Factors of the Institute for Biomedical Research. Amounts of lead and cadmium were established after "dry" mineralisation using "Perkin-Elmer Zeeman/3030" model electrothermic atomic absorption spectrophotometer (ETG AAS/Zeeman). It was established that lead is absorbed most efficiently after estimation of absorption capacity of cellular fibers. About 10.73% of lead crosses tinctures and extracts, better cadmium--49.63%. Herbs of Leonurus cardiaca L. are the best in holding back lead and cadmium. About 14.5% of lead and cadmium crosses the tincture of herbs Leonurus cardiaca L. We estimated the factors of heavy metals (lead, cadmium) in the liquid extracts of Crataegus monogyna Jacq. and Echinacea purpurea Moench., tincture of Leonurus cardiaca L. after investigations of heavy metals (lead, cadmium) in drugs and preparations of it. The amounts of heavy metals (lead, cadmium) don't exceed the allowable norms in fruits of Crataegus monogyna Jacq., herbs of Leonurus cardiaca L. and Echinacea purpurea Moench. after estimation of lead and cadmium extraction factors, the maximum of acceptable daily intake and the quantity of drugs consumption in day.

Management of Small Quantity of Nuclear Material at Locations Outside Facilities in Korea

Energy Technology Data Exchange (ETDEWEB)

Park, Seung Sik; Kim, Ki Hyun [KAERI, Daejeon (Korea, Republic of)

2016-05-15

Small quantity of nuclear material (SQNM) is prescribed to be less than specified minimum quantities of nuclear material in a facility. SQNM is used at the locations called locations outside facilities (LOFs). LOFs are used to control the locations and installations that store nuclear materials under one effective Kg, respectively. Holders of SQNM don't need to require a license for use or possession of Uranium or Thorium exclusively for non-nuclear activities, or neither report them to the System of Accounting for and Control of nuclear material (SSAC) under specified quantities according to the Atomic Safety Law. Well defined safeguards law is fundamental to the effective control of nuclear material, facilities and nuclear related activities. In the current nuclear safety legislation, there are some exceptive clauses. Users of SQNM don't need to require a license for use or possession of Uranium or Thorium exclusively for non-nuclear activities, or not report them to the national authority below specified amount.

Energy Drinks and Binge Drinking Predict College Students' Sleep Quantity, Quality, and Tiredness.

Science.gov (United States)

Patrick, Megan E; Griffin, Jamie; Huntley, Edward D; Maggs, Jennifer L

2018-01-01

This study examines whether energy drink use and binge drinking predict sleep quantity, sleep quality, and next-day tiredness among college students. Web-based daily data on substance use and sleep were collected across four semesters in 2009 and 2010 from 667 individuals for up to 56 days each, yielding information on 25,616 person-days. Controlling for average levels of energy drink use and binge drinking (i.e., 4+ drinks for women, 5+ drinks for men), on days when students consumed energy drinks, they reported lower sleep quantity and quality that night, and greater next-day tiredness, compared to days they did not use energy drinks. Similarly, on days when students binge drank, they reported lower sleep quantity and quality that night, and greater next-day tiredness, compared to days they did not binge drink. There was no significant interaction effect between binge drinking and energy drink use on the outcomes.

Management of Small Quantity of Nuclear Material at Locations Outside Facilities in Korea

International Nuclear Information System (INIS)

Park, Seung Sik; Kim, Ki Hyun

2016-01-01

Small quantity of nuclear material (SQNM) is prescribed to be less than specified minimum quantities of nuclear material in a facility. SQNM is used at the locations called locations outside facilities (LOFs). LOFs are used to control the locations and installations that store nuclear materials under one effective Kg, respectively. Holders of SQNM don't need to require a license for use or possession of Uranium or Thorium exclusively for non-nuclear activities, or neither report them to the System of Accounting for and Control of nuclear material (SSAC) under specified quantities according to the Atomic Safety Law. Well defined safeguards law is fundamental to the effective control of nuclear material, facilities and nuclear related activities. In the current nuclear safety legislation, there are some exceptive clauses. Users of SQNM don't need to require a license for use or possession of Uranium or Thorium exclusively for non-nuclear activities, or not report them to the national authority below specified amount

The preparation by extrusion/spheronization and the properties of pellets containing drugs, microcrystalline cellulose and glyceryl monostearate.

Science.gov (United States)

Chatchawalsaisin, Jittima; Podczeck, Fridrun; Newton, J Michael

2005-01-01

Pellets have been prepared by extrusion and spheronization containing microcrystalline cellulose (MCC) and four model drugs with decreasing order of solubility, paracetamol (P), diclofenac sodium (D), ibuprofen (IB) and indomethacin (IN) at a 10% level with and without the addition of a range of levels of glyceryl monostearate (GMS). The drugs differed in their response to extrusion in that all formulations containing the drug D had a 'steady state' extrusion profile whereas the other three drugs exhibited 'forced flow' indicating the possibility of water migration during the process of ram extrusion. The presence of GMS did not influence this effect. The drug D also required consistently less water to function than the other three drugs. In spite of these differences in extrusion performance, it was possible to prepare satisfactory pellets from formulations of all the drugs with 0, 30 and 60% GMS combined with 90, 60 or 30% of MCC at a range of water levels. It was also possible to prepare pellets containing the drug D with 70, 80 and 90% GMS, with corresponding quantities of 20, 10 and 0% of MCC. It was also possible to prepare the pellet formulations by dispersing the drugs in molten GMS, grinding and processing this with MCC and water. Such systems retained the processing characteristics of the composition made by the blending of the powder. The presence of GMS in all cases reduced the quantity of water required for the process to function. The steady state or the mean of the range of the forces observed during forced flow, were dependent on the composition and the quantity of water added. The surface of the extrudate appeared smooth and measurements of surface roughness established that the value of the rugosity R(a) for any of the extrudates did not exceed 6 microm. The extrudate diameter was found to increase with the quantity of GMS in the formulation. The pellets produced were all within a relatively narrow size range (three sieve fractions of a root two

Evaluation of specific absorption rate as a dosimetric quantity for electromagnetic fields bioeffects.

Directory of Open Access Journals (Sweden)

Dimitris J Panagopoulos

Full Text Available PURPOSE: To evaluate SAR as a dosimetric quantity for EMF bioeffects, and identify ways for increasing the precision in EMF dosimetry and bioactivity assessment. METHODS: We discuss the interaction of man-made electromagnetic waves with biological matter and calculate the energy transferred to a single free ion within a cell. We analyze the physics and biology of SAR and evaluate the methods of its estimation. We discuss the experimentally observed non-linearity between electromagnetic exposure and biological effect. RESULTS: WE FIND THAT: a The energy absorbed by living matter during exposure to environmentally accounted EMFs is normally well below the thermal level. b All existing methods for SAR estimation, especially those based upon tissue conductivity and internal electric field, have serious deficiencies. c The only method to estimate SAR without large error is by measuring temperature increases within biological tissue, which normally are negligible for environmental EMF intensities, and thus cannot be measured. CONCLUSIONS: SAR actually refers to thermal effects, while the vast majority of the recorded biological effects from man-made non-ionizing environmental radiation are non-thermal. Even if SAR could be accurately estimated for a whole tissue, organ, or body, the biological/health effect is determined by tiny amounts of energy/power absorbed by specific biomolecules, which cannot be calculated. Moreover, it depends upon field parameters not taken into account in SAR calculation. Thus, SAR should not be used as the primary dosimetric quantity, but used only as a complementary measure, always reporting the estimating method and the corresponding error. Radiation/field intensity along with additional physical parameters (such as frequency, modulation etc which can be directly and in any case more accurately measured on the surface of biological tissues, should constitute the primary measure for EMF exposures, in spite of similar

Evaluation of specific absorption rate as a dosimetric quantity for electromagnetic fields bioeffects.

Science.gov (United States)

Panagopoulos, Dimitris J; Johansson, Olle; Carlo, George L

2013-01-01

To evaluate SAR as a dosimetric quantity for EMF bioeffects, and identify ways for increasing the precision in EMF dosimetry and bioactivity assessment. We discuss the interaction of man-made electromagnetic waves with biological matter and calculate the energy transferred to a single free ion within a cell. We analyze the physics and biology of SAR and evaluate the methods of its estimation. We discuss the experimentally observed non-linearity between electromagnetic exposure and biological effect. WE FIND THAT: a) The energy absorbed by living matter during exposure to environmentally accounted EMFs is normally well below the thermal level. b) All existing methods for SAR estimation, especially those based upon tissue conductivity and internal electric field, have serious deficiencies. c) The only method to estimate SAR without large error is by measuring temperature increases within biological tissue, which normally are negligible for environmental EMF intensities, and thus cannot be measured. SAR actually refers to thermal effects, while the vast majority of the recorded biological effects from man-made non-ionizing environmental radiation are non-thermal. Even if SAR could be accurately estimated for a whole tissue, organ, or body, the biological/health effect is determined by tiny amounts of energy/power absorbed by specific biomolecules, which cannot be calculated. Moreover, it depends upon field parameters not taken into account in SAR calculation. Thus, SAR should not be used as the primary dosimetric quantity, but used only as a complementary measure, always reporting the estimating method and the corresponding error. Radiation/field intensity along with additional physical parameters (such as frequency, modulation etc) which can be directly and in any case more accurately measured on the surface of biological tissues, should constitute the primary measure for EMF exposures, in spite of similar uncertainty to predict the biological effect due to non-linearity.

Management of Water Quantity and Quality Based on Copula for a Tributary to Miyun Reservoir, Beijing

Science.gov (United States)

Zang, N.; Wang, X.; Liang, P.

2017-12-01

Due to the complex mutual influence between water quantity and water quality of river, it is difficult to reflect the actual characters of the tributaries to reservoir. In this study, the acceptable marginal probability distributions for water quantity and quality of reservoir inflow were calculated. A bivariate Archimedean copula was further applied to establish the joint distribution function of them. Then multiple combination scenarios of water quantity and water quality were designed to analyze their coexistence relationship and reservoir management strategies. Taking Bai river, an important tributary into the Miyun Reservoir, as a study case. The results showed that it is feasible to apply Frank copula function to describe the jointed distribution function of water quality and water quantity for Bai river. Furthermore, the monitoring of TP concentration needs to be strengthen in Bai river. This methodology can be extended to larger dimensions and is transferable to other reservoirs via establishment of models with relevant data for a particular area. Our findings help better analyzing the coexistence relationship and influence degree of the water quantity and quality of the tributary to reservoir for the purpose of water resources protection.

Preparation of Fluorine-Doped TiO2 Photocatalysts with Controlled Crystalline Structure

Directory of Open Access Journals (Sweden)

N. Todorova

2008-01-01

Full Text Available Nanocrystalline F-doped TiO2 powders were prepared by sol-gel route. The thermal behavior of the powders was recorded by DTA/TG technique. The crystalline phase of the fluorinated TiO2 powders was determined by X-ray diffraction technique. It was demonstrated that F-doping using CF3COOH favors the formation of rutile along with anatase phase even at low temperature. Moreover, the rutile's phase content increases with the increase of the quantity of the fluorine precursor in the starting solution. The surface area of the powders and the pore size distribution were studied by N2 adsorption-desorption using BET and BJH methods. X-ray photoelectron spectroscopy (XPS revealed that the fluorine is presented in the TiO2 powders mainly as metal fluoride in quantities ∼16 at %. The F-doped TiO2 showed a red-shift absorption in UV-vis region which was attributed to the increased content of rutile phase in the powders. The powders exhibited enhanced photocatalytic activity in decomposition of acetone.

The research of the quantitative prediction of the deposits concentrated regions of the large and super-large sized mineral deposits in China

International Nuclear Information System (INIS)

Zhao Zhenyu; Wang Shicheng

2003-01-01

By the general theory and method of mineral resources prognosis of synthetic information, the locative and quantitative prediction of the large and super-large sized mineral deposits of solid resources of 1 : 5,000,000 are developed in china. The deposit concentrated regions is model unit, the anomaly concentrated regions is prediction unit. The mineral prognosis of synthetic information is developed on GIS platform. The technical route and work method of looking for the large and super-large sized mineral resources and basic principle of compiling attribute table of the variables and the response variables are mentioned. In research of prediction of resources quantity, the locative and quantitative prediction are processed by separately the quantification theory Ⅲ and the corresponding characteristic analysis, two methods are compared. It is very important for resources prediction of western ten provinces in china, it is helpful. (authors)

Compound antimalarial ethosomal cataplasm: preparation, evaluation, and mechanism of penetration enhancement

Directory of Open Access Journals (Sweden)

Shen S

2015-06-01

Full Text Available Shuo Shen, Shu-Zhi Liu, Yu-Shi Zhang, Mao-Bo Du, Ai-Hua Liang, Li-Hua Song, Zu-Guang Ye Institute of Chinese Materia Medica, China Academy of Chinese Medical Sciences, Beijing, People’s Republic of China Abstract: Malaria is still a serious public health problem in some parts of the world. The problems of recurrence and drug resistance are increasingly more serious. Thus, it is necessary to develop a novel antimalarial agent. The objectives of this study were to construct a novel compound antimalarial transdermal nanosystem–ethosomal cataplasm, to investigate its characteristics and efficiency, and to systematically explore the penetration-enhancing mechanisms of ethosomal cataplasm. Artesunate-loaded ethosomes and febrifugine-loaded ethosomes were prepared, and their characteristics were evaluated. Drug-loaded ethosomes were incorporated in the matrix of cataplasm to form the compound antimalarial ethosomal cataplasm. With the help of ethosomal technology, the accumulated permeation quantity of artesunate significantly increased at 8 hours after administration, which was 1.57 times as much as that of conventional cataplasm. Soon after administration, the ethosomal cataplasm could make a large quantity of antimalarial drug quickly penetrate through skin, then the remaining drug in the ethosomal cataplasm could be steadily released. These characteristics of ethosomal cataplasm are favorable for antimalarial drugs to kill Plasmodium spp. quickly and prevent the resurgence of Plasmodium spp. As expected, the ethosomal cataplasm showed good antimalarial efficiency in this experiment. The negative conversion rates were 100% and the recurrence rates were 0% at all dosages. The mechanism of penetration enhancement of the ethosomal cataplasm was systematically explored using an optics microscope, polarization microscope, and transmission electron microscopy. The microstructure, ultrastructure, and birefringent structure in skin were observed. Data

Ovarian cyst fluid of serous ovarian tumors contains large quantities of the brain amino acid N-acetylaspartate.

NARCIS (Netherlands)

Kolwijck, E.; Wevers, R.A.; Engelke, U.F.H.; Woudenberg, J.; Bulten, J.; Blom, H.J.; Massuger, L.F.A.G.

2010-01-01

BACKGROUND: In humans, N-acetyl L-aspartate (NAA) has not been detected in other tissues than the brain. The physiological function of NAA is yet undefined. Recently, it has been suggested that NAA may function as a molecular water pump, responsible for the removal of large amounts of water from the

Organizational citizenship behavior and the quantity and quality of work group performance.

Science.gov (United States)

Podsakoff, P M; Ahearne, M; MacKenzie, S B

1997-04-01

Despite the widespread interest in the topic of organizational citizenship behaviors (OCBs), little empirical research has tested the fundamental assumption that these forms of behavior improve the effectiveness of work groups or organizations in which they are exhibited. In the present study, the effects of OCBs on the quantity and quality of the performance of 218 people working in 40 machine crews in a paper mill located in the Northeastern United States were examined. The results indicate that helping behavior and sportsmanship had significant effects on performance quantity and that helping behavior had a significant impact on performance quality. However, civic virtue had no effect on either performance measure.

Calculation of skin dose due to beta contamination using the new quantity of the ICRP 116: the local skin dose

International Nuclear Information System (INIS)

Bourgois, L.; Menard, S.; Comte, N.

2017-01-01

Values of the new protection quantity Local Skin Dose 'LSD', introduced by the International Commission on Radiological Protection (ICRP) Publication 116, were calculated for 134 β - or β + emitting radionuclides, using the Monte Carlo code MCNP6. Two types of source geometry are considered: a point source and disc-type surface contamination (the source is placed in contact with the skin). This new protection quantity is compared with the operational quantity H2 (0.07, 0 deg.), leading us to conclude that, in accordance with the rules of the ICRP, the operational quantity over-estimates the protection quantity to a reasonable extent, except in very rare cases for very low average beta energies. Thus, with the new skin model described in ICRP 116, there are no longer any major differences between the operational quantities and protection quantities estimated with the skin model described in ICRP 74. (authors)

Color Coding of Circuit Quantities in Introductory Circuit Analysis Instruction

Science.gov (United States)

Reisslein, Jana; Johnson, Amy M.; Reisslein, Martin

2015-01-01

Learning the analysis of electrical circuits represented by circuit diagrams is often challenging for novice students. An open research question in electrical circuit analysis instruction is whether color coding of the mathematical symbols (variables) that denote electrical quantities can improve circuit analysis learning. The present study…

21 CFR 201.62 - Declaration of net quantity of contents.

Science.gov (United States)

2010-04-01

..., 250 milligrams each”: Provided, That: (1) In the case of a firmly established, general consumer usage... firmly established, general consumer usage and trade custom of employing different common fractions in... a declaration of net quantity blown, embossed, or molded on a glass or plastic surface is...

Large wood in the Snowy River estuary, Australia

Science.gov (United States)

Hinwood, Jon B.; McLean, Errol J.

2017-02-01

In this paper we report on 8 years of data collection and interpretation of large wood in the Snowy River estuary in southeastern Australia, providing quantitative data on the amount, sources, transport, decay, and geomorphic actions. No prior census data for an estuary is known to the authors despite their environmental and economic importance and the significant differences between a fluvial channel and an estuarine channel. Southeastern Australian estuaries contain a significant quantity of large wood that is derived from many sources, including river flood flows, local bank erosion, and anthropogenic sources. Wind and tide are shown to be as important as river flow in transporting and stranding large wood. Tidal action facilitates trapping of large wood on intertidal bars and shoals; but channels are wider and generally deeper, so log jams are less likely than in rivers. Estuarine large wood contributes to localised scour and accretion and hence to the modification of estuarine habitat, but in the study area it did not have large-scale impacts on the hydraulic gradients nor the geomorphology.

High Throughput Microplate Respiratory Measurements Using Minimal Quantities Of Isolated Mitochondria

Science.gov (United States)

Rogers, George W.; Brand, Martin D.; Petrosyan, Susanna; Ashok, Deepthi; Elorza, Alvaro A.; Ferrick, David A.; Murphy, Anne N.

2011-01-01

Recently developed technologies have enabled multi-well measurement of O2 consumption, facilitating the rate of mitochondrial research, particularly regarding the mechanism of action of drugs and proteins that modulate metabolism. Among these technologies, the Seahorse XF24 Analyzer was designed for use with intact cells attached in a monolayer to a multi-well tissue culture plate. In order to have a high throughput assay system in which both energy demand and substrate availability can be tightly controlled, we have developed a protocol to expand the application of the XF24 Analyzer to include isolated mitochondria. Acquisition of optimal rates requires assay conditions that are unexpectedly distinct from those of conventional polarography. The optimized conditions, derived from experiments with isolated mouse liver mitochondria, allow multi-well assessment of rates of respiration and proton production by mitochondria attached to the bottom of the XF assay plate, and require extremely small quantities of material (1–10 µg of mitochondrial protein per well). Sequential measurement of basal, State 3, State 4, and uncoupler-stimulated respiration can be made in each well through additions of reagents from the injection ports. We describe optimization and validation of this technique using isolated mouse liver and rat heart mitochondria, and apply the approach to discover that inclusion of phosphatase inhibitors in the preparation of the heart mitochondria results in a specific decrease in rates of Complex I-dependent respiration. We believe this new technique will be particularly useful for drug screening and for generating previously unobtainable respiratory data on small mitochondrial samples. PMID:21799747

High throughput microplate respiratory measurements using minimal quantities of isolated mitochondria.

Directory of Open Access Journals (Sweden)

George W Rogers

Full Text Available Recently developed technologies have enabled multi-well measurement of O(2 consumption, facilitating the rate of mitochondrial research, particularly regarding the mechanism of action of drugs and proteins that modulate metabolism. Among these technologies, the Seahorse XF24 Analyzer was designed for use with intact cells attached in a monolayer to a multi-well tissue culture plate. In order to have a high throughput assay system in which both energy demand and substrate availability can be tightly controlled, we have developed a protocol to expand the application of the XF24 Analyzer to include isolated mitochondria. Acquisition of optimal rates requires assay conditions that are unexpectedly distinct from those of conventional polarography. The optimized conditions, derived from experiments with isolated mouse liver mitochondria, allow multi-well assessment of rates of respiration and proton production by mitochondria attached to the bottom of the XF assay plate, and require extremely small quantities of material (1-10 µg of mitochondrial protein per well. Sequential measurement of basal, State 3, State 4, and uncoupler-stimulated respiration can be made in each well through additions of reagents from the injection ports. We describe optimization and validation of this technique using isolated mouse liver and rat heart mitochondria, and apply the approach to discover that inclusion of phosphatase inhibitors in the preparation of the heart mitochondria results in a specific decrease in rates of Complex I-dependent respiration. We believe this new technique will be particularly useful for drug screening and for generating previously unobtainable respiratory data on small mitochondrial samples.

Enhancing preparation for large Nipah outbreaks beyond Bangladesh: Preventing a tragedy like Ebola in West Africa

Directory of Open Access Journals (Sweden)

Halsie Donaldson

2018-07-01

Full Text Available The Nipah virus has been transmitted from person-to-person via close contact in non-urban parts of India (including Kerala May 2018, Bangladesh, and the Philippines. It can cause encephalitis and pneumonia, and has a high case fatality rate. Nipah is a One Health zoonotic infectious disease linked to fruit bats, and sometimes pigs or horses. We advocate anticipating and preparing for urban and larger rural outbreaks of Nipah. Immediate enhanced preparations would include standardized guidance on infection prevention and control, and personal protective equipment, from the World Health Organization (WHO on their OpenWHO website and 2018 “Managing Epidemics” handbook, along with adding best clinical practices by experts in countries with multiple outbreaks such as Bangladesh and India. Longer-term enhanced preparations include accelerating development of field diagnostics, antiviral drugs, immune-based therapies, and vaccines. WHO-coordinated multi-partner protocols to test investigational treatments, diagnostics, and vaccines are needed, by analogy to such protocols for Ebola during the unanticipated pan-epidemic in Guinea, Liberia, and Sierra Leone. Anticipating and preparing now for urban and rural Nipah outbreaks in nations with no experience with Nipah will help avoid the potential for what the United Nations 2016 report on Ebola in West Africa called a “preventable tragedy”. Keywords: Nipah epidemics beyond Bangladesh, Nipah countermeasures, Nipah, One Health

Skin dose estimation due to a contamination by a radionuclide β emitter: are doses equivalent good estimator of protection quantities?

International Nuclear Information System (INIS)

Bourgois, L.

2011-01-01

When handling radioactive β emitters, measurements in terms of personal dose equivalents H p (0.07) are used to estimate the equivalent dose limit to skin or extremities given by regulations. First of all, analytical expressions for individual dose equivalents H p (0.07) and equivalent doses to the extremities H skin are given for a point source and for contamination with a radionuclide β emitter. Second of all, operational quantities and protection quantities are compared. It is shown that in this case the operational quantities significantly overstate the protection quantities. For a skin contamination the ratio between operational quantities and protection quantities is 2 for a maximum β energy of 3 MeV and 90 for a maximum β energy of 150 keV. (author)

Improved wave functions for large-N expansions

International Nuclear Information System (INIS)

Imbo, T.; Sukhatme, U.

1985-01-01

Existing large-N expansions of radial wave functions phi/sub n/,l(r) are only accurate near the minimum of the effective potential. Within the framework of the shifted 1/N expansion, we use known analytic results to motivate a simple modification so that the improved wave functions are accurate over a wide range of r and any choice of quantum numbers n and l. It is shown that these wave functions yield simple and accurate analytic expressions for certain quantities of interest in quarkonium physics

Dependence of freshwater plants on quantity of carbon dioxide and hydrogen ion concentration illustrated through experimental investigations

Energy Technology Data Exchange (ETDEWEB)

Nielsen, E S

1944-01-01

By culture experiments with the freshwater plants Helodea canadensis and Ceratophyllum demersum, in which both the contents of carbon dioxide and pH of the water were varied, it was shown that ph within the area 4.5 to 8.2 has no appreciable influence on the growth. The supply of carbon dioxide, on the other hand, has very great influence. The fact that the two freshwater plants mentioned in Denmark are found in alkaline water only, is due to the contents of assimilable carbon dioxide decreasing with decrease of pH. While thus in alkaline water there are generally large quantities of bicarbonate, from which half of the carbon dioxide may be utilized in the assimilation, there is in acid water (pH below 4.5) no bicarbonate. Carbon dioxide in true solution and bicarbonate carbon dioxide behave differently as sources of carbon dioxide for the assimilation; this is amongst other things due to the fact that the absorption of the carbon dioxide through the bicarbonate is made actively on the part of the plant. The investigations which illustrate the influence of the quantity of carbon dioxide on the intensity of assimilation were made on submersed plants in water containing bicarbonate, and therefore give quite different results in relation to terraneous plants, where the carbon dioxide is exclusively assimilated.

Preparation and evaluation of reference materials for accountancy analysis. (1) Preparation and evaluation method

International Nuclear Information System (INIS)

Takamatsu, Mai; Kacchi, Tomokazu; Murakami, Toshiki; Ai, Hironobu; Sumi, Mika; Abe, Katsuo; Kageyama, Tomio; Nakazawa, Hiroaki

2009-01-01

Isotope dilution mass spectrometry method used for the accountancy analysis at nuclear fuel facilities requires the standard materials called LSD (Large Size Dried) spike. Generally, LSD spikes are prepared from certified reference materials (CRMs) which supplied from foreign laboratories. However, the difficulty of Pu CRM importation is increasing. It is important for safeguards to attain and continue high reliable accountancy analysis and stable securing of LSD spike is essential. Therefore, in order to conserve CRMs, several types of LSD spike were prepared under collaboration work between JAEA and JNFL, such as the amount of nuclear material in one LSD spike is decreased and others. Practical test with actual samples were performed at JNFL Rokkasho reprocessing plant, and those results were compared with the results obtained by using LSD spike which supplied from foreign laboratory. Preparation and verification analysis of LSD spikes and evaluation of uncertainty based on ISO-GUM will be presented. (author)

Peer Assessment for Construction Management and Quantity Surveying Students

Directory of Open Access Journals (Sweden)

Patricia McLaughlin

2012-11-01

Full Text Available Students undertaking the Bachelor of ConstructionManagement degree course at RMIT University, Melbourne,qualify for registration with the Australian Institute ofQuantity Surveyors (AIQS and the Australian Institute ofBuilding (AIB upon graduation. Over the past decade thedegree course has been constantly upgraded and altered inline with recommendations from professional bodies such asthese and other industry partners. In 1994 the Departmentof Building and Construction Economics re-assesseda range of subjects including the first year technologysubjects. Out of the review a problem-based integratedlearning unit was developed and tested. This unit has nowbeen in place for ten years.Quantity surveying and construction management likemost other professions in the construction industryrequire teamwork and advanced consultation skills. Theseskills may be learnt through experience but there isconsiderable evidence that these skills can be taught in theundergraduate years. Therefore in line with team-basedapproaches used in industry and professional constructionsettings, this year a new assessment model - peerassessment - will be applied to the problem-based learningunit. This paper describes the procedures and processesused to introduce the change and examines the theoreticalbase upon which the model was developed.

Large Eddy Simulation of stratified flows over structures

Directory of Open Access Journals (Sweden)

Brechler J.

2013-04-01

Full Text Available We tested the ability of the LES model CLMM (Charles University Large-Eddy Microscale Model to model the stratified flow around three dimensional hills. We compared the quantities, as the height of the dividing streamline, recirculation zone length or length of the lee waves with experiments by Hunt and Snyder[3] and numerical computations by Ding, Calhoun and Street[5]. The results mostly agreed with the references, but some important differences are present.

Hazardous Waste Management for the Small Quantity Generator. Teacher Edition.

Science.gov (United States)

Oklahoma State Dept. of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This instructional package for teaching about the regulations imposed on small quantity generators by the Environmental Protection Agency (EPA) under the Resource Conservation Recovery Act is organized around ll program objectives: students will be able to (l) determine a hazardous waste from lists or by identifying characteristics; (2) identify…

Quantity and quality of written feedback, action plans, and student ...

African Journals Online (AJOL)

Background. Mini-clinical-evaluation exercise (mini-CEX) assessment forms that have been modified with the addition of specific spaces on separate sheets are expected to improve the quantity and quality of written feedback and the action plan for further learning which is agreed upon, and to encourage written reflection.

The Management Challenge: Handling Exams Involving Large Quantities of Students, on and off Campus--A Design Concept

Science.gov (United States)

Larsson, Ken

2014-01-01

This paper looks at the process of managing large numbers of exams efficiently and secure with the use of a dedicated IT support. The system integrates regulations on different levels, from national to local, (even down to departments) and ensures that the rules are employed in all stages of handling the exams. The system has a proven record of…

Effect of scale and quantity on the cost and performance of energy technologies: a literature review

International Nuclear Information System (INIS)

Hill, D.

1983-11-01

Traditionally, a six-tenths power law stated that cost increased by only half with a doubling of plant size, reducing cost per unit of capacity to 75%. Problems during construction in the past two decades have largely nullified the expected savings. Thermal efficiency improves with size in both coal and nuclear plants, but plant availability declines. These trends suggest that an optimal size for nuclear plants may be somewhat less than 1000 MW(e). Judged by a study of the cost of electricity generated during the 1970s, however, operational savings substantially restored economies of scale to nuclear plants but not to coal plants. The alternative to building larger plants is to build more small plants. In field construction, a second plant at the same site costs about 90% of the first, and a doubling of the number of plants built by an architect-engineer appears to reduce average cost to about 93%. In a variety of manufacturing industries, the learning curve is steeper. In the few cases where learning curves are mentioned in manufacturing studies of new energy technologies, however, a reduction in cost to only about 90% with a doubling of quantity is assumed. Most of the cost of new energy technologies such as photovoltaic arrays and fuel cells will be due to conventional equipment, structure, and manufacturing methods. It should therefore be possible to estimate size-quantity cost tradeoffs with some confidence to help establish optimal plant or module sizes

Effects of herbivore exclosures on variation in quality and quantity of ...

African Journals Online (AJOL)

Effects of herbivore exclosures on variation in quality and quantity of plants among ... commercial and game) and among habitat types (open savanna, rocky and pan) in a semiarid savanna in South Africa. ... AJOL African Journals Online.

Optimising concentrations of antimicrobial agents in pharmaceutical preparations: Case of an oral solution of glycerol and an ophthalmic solution containing cysteamine.

Science.gov (United States)

Chan Hew Wai, A; Becasse, P; Tworski, S; Pradeau, D; Planas, V

2014-11-01

In the context of current distrust of antimicrobial preservatives, the quantities of these substances in two pharmaceutical formulas were studied: an ophthalmic solution of cysteamine preserved benzalkonium chloride at 1mg/5mL and Glycerotone(®) preserved with sorbic acid at 0.1g/100g. The purpose of this work was to verify that a reduction of the quantities of preservative continues to fulfil the requirements for antimicrobial preservation. The Test of efficacy of antimicrobial preservation, section 5.1.3 of the 8th edition of the European Pharmacopoeia, was carried out on each formulation prepared with decreasing quantities of preservative. The results show that formulations whose preservative concentration was reduced by a factor of four remained compliant with standards. It is to be noted that in formulas without preservative, fungal growth was observed in both the solution of Glycerotone(®) and the ophthalmic solution containing cysteamine. Although there is no question that an antimicrobial preservative is necessary, the quantity of preservative can be reduced without deteriorating the quality of the pharmaceutical product but the minimal effective concentration remains to be determined. The formulations of many pharmaceutical products should therefore be examined in order to limit the quantities of preservative while continuing to guarantee patient's safety. Copyright © 2014 Elsevier Masson SAS. All rights reserved.

Securing water quality and quantity: Research and development perspective

CSIR Research Space (South Africa)

Pienaar, H

2012-10-01

Full Text Available : ? economic growth & development ? human & environmental needs ? meeting international obligations ? energy needs (strategic water users) ? ensuring availability and allocation (all other users) ? CSIR 2012 Slide 3 Background ? SA 30th driest country... and quantity: Research and development perspective 4th Biennial Conference Harrison Pienaar 10 October 2012 Presentation outline ? Introduction and background to water in South Africa ? Transboundary water resource aspects ? Water related challenges...

Mei Symmetry and New Conserved Quantities of Tzénoff Equations for the Variable Mass Higher-Order Nonholonomic System

International Nuclear Information System (INIS)

Zheng Shi-Wang; Wang Jian-Bo; Chen Xiang-Wei; Xie Jia-Fang

2012-01-01

Operational systems of spacecraft are general variable mass mechanics systems, and their symmetries and conserved quantities imply profound physical rules of the space system. We study the Mei symmetry of Tzénoff equations for a variable mass nonholonomic system and the new conserved quantities derived. The function expression of the new conserved quantities and the criterion equation which deduces these conserved quantities are presented. This result has some theoretical values in further research of conservation laws obeyed by the variable mass system. (general)

21 CFR 516.36 - Insufficient quantities of MUMS-designated drugs.

Science.gov (United States)

2010-04-01

... SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS NEW ANIMAL DRUGS FOR MINOR USE AND MINOR SPECIES Designation of a Minor Use or Minor Species New Animal Drug § 516.36 Insufficient quantities of... the 7-year period of exclusive marketing rights. (b) If, within the time that FDA specifies, the...

21 CFR 801.62 - Declaration of net quantity of contents.

Science.gov (United States)

2010-04-01

... the case of a firmly established general consumer usage and trade custom of declaring the quantity of... there exists a firmly established, general consumer usage and trade custom of employing different common..., embossed, or molded on a glass or plastic surface is permissible when all label information is so formed on...

Photographs in Dutch History Textbooks: Quantity, type and educational use

NARCIS (Netherlands)

M. Kleppe (Martijn)

2010-01-01

textabstractThis article demonstrates a media scientific approach by studying the use of photographs in Dutch History textbooks for High School pupils in the period 1970 – 2000. The quantity of photos has been determined as well as the types of pictures and its use as educational tool. Results show

Is the dose equivalent index a quantity to be measured

International Nuclear Information System (INIS)

Wagner, S.R.

1980-01-01

The following modifying factors are briefly considered in relation to the ambiguities and limitations of the Dose Equivalent Index: 1) Variations with time or of the movement of the exposed person 2) Irradiation geometry 3) Effect of radiation energy 4) Instrument performance and calibration, and other operational quantities. (U.K.)