WorldWideScience

Sample records for preparation area chem-prep

  1. Chem-prep PZT95/5 for neutron generator applications : the effect of pore former type and density on the depoling behavior of chemically prepared PZT 95/5 ceramics.

    Energy Technology Data Exchange (ETDEWEB)

    Lockwood, Steven John; Scofield, Timothy W.; Yang, Pin; Voigt, James A.; Tuttle, Bruce Andrew; Moore, Roger Howard

    2003-10-01

    The hydrostatically induced ferroelectric(FE)-to-antiferroelectric(AFE) phase transformation for chemically prepared niobium modified PZT 95/5 ceramics was studied as a function of density and pore former type (Lucite or Avicel). Special attention was placed on the effect of different pore formers on the charge release behavior associated with the FE-to-AFE phase transformation. Within the same density range (7.26 g/cm3 to 7.44 g/cm3), results showed that ceramics prepared with Lucite pore former exhibit a higher bulk modulus and a sharper polarization release behavior than those prepared with Avicel. In addition, the average transformation pressure was 10.7% greater and the amount of polarization released was 2.1% higher for ceramics with Lucite pore former. The increased transformation pressure was attributed to the increase of bulk modulus associated with Lucite pore former. Data indicated that a minimum volumetric transformational strain of -0.42% was required to trigger the hydrostatically induced FE-to-AFE phase transformation. This work has important implications for increasing the high temperature charge output for neutron generator power supply units.

  2. Hydrostatic, uniaxial, and triaxial compression tests on unpoled "Chem-prep" PZT 95/5-2Nb ceramic within temperature range of -55 to 75 degrees C.

    Energy Technology Data Exchange (ETDEWEB)

    Zeuch, David Henry; Montgomery, Stephen Tedford; Lee, Moo Yul; Hofer, John H.

    2003-10-01

    Sandia is currently developing a lead-zirconate-titanate ceramic 95/5-2Nb (or PNZT) from chemically prepared ('chem-prep') precursor powders. Previous PNZT ceramic was fabricated from the powders prepared using a 'mixed-oxide' process. The specimens of unpoled PNZT ceramic from batch HF803 were tested under hydrostatic, uniaxial, and constant stress difference loading conditions within the temperature range of -55 to 75 C and pressures to 500 MPa. The objective of this experimental study was to obtain mechanical properties and phase relationships so that the grain-scale modeling effort can develop and test its models and codes using realistic parameters. The stress-strain behavior of 'chem-prep' PNZT under different loading paths was found to be similar to that of 'mixed-oxide' PNZT. The phase transformation from ferroelectric to antiferroelectric occurs in unpoled ceramic with abrupt increase in volumetric strain of about 0.7 % when the maximum compressive stress, regardless of loading paths, equals the hydrostatic pressure at which the transformation otherwise takes place. The stress-volumetric strain relationship of the ceramic undergoing a phase transformation was analyzed quantitatively using a linear regression analysis. The pressure (P{sub T1}{sup H}) required for the onset of phase transformation with respect to temperature is represented by the best-fit line, P{sub T1}{sup H} (MPa) = 227 + 0.76 T (C). We also confirmed that increasing shear stress lowers the mean stress and the volumetric strain required to trigger phase transformation. At the lower bound (-55 C) of the tested temperature range, the phase transformation is permanent and irreversible. However, at the upper bound (75 C), the phase transformation is completely reversible as the stress causing phase transformation is removed.

  3. Chem-Prep PZT 95/5 for neutron generator applications : development of laboratory-scale powder processing operations.

    Energy Technology Data Exchange (ETDEWEB)

    Montoya, Ted V.; Moore, Roger Howard; Spindle, Thomas Lewis Jr.

    2003-12-01

    Chemical synthesis methods are being developed as a future source of PZT 95/5 powder for neutron generator voltage bar applications. Laboratory-scale powder processes were established to produce PZT billets from these powders. The interactions between calcining temperature, sintering temperature, and pore former content were studied to identify the conditions necessary to produce PZT billets of the desired density and grain size. Several binder systems and pressing aids were evaluated for producing uniform sintered billets with low open porosity. The development of these processes supported the powder synthesis efforts and enabled comparisons between different chem-prep routes.

  4. Preparation of Pu Target with Small Area

    Institute of Scientific and Technical Information of China (English)

    SUN; Xiao-yi; MAO; Guo-shu; HUANG; Kun; YANG; Lei; YANG; Su-liang; YANG; Chun-li; SUN; Hong-qing; MA; Peng

    2015-01-01

    Plutonium can be electrodeposited in ammonium oxalate,ammonium sulfate and ammonium chloride systems,but there is white layer appeared when the diameter of the active area is7mm and Pu is electrodeposited in isopropanol,and large amount of hydrogen is generated near the cathode in ammonium sulfate,which covers

  5. Propellant Preparation Laboratory Complex (Area1-21)

    Data.gov (United States)

    Federal Laboratory Consortium — Description: Area 1-21 is an explosion resistant complex of nine cells built into the side of a granite ridge. Three solid propellant cutting cells are housed in the...

  6. Study of Preparation of Large Area Standard Source

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    With increasingly widespread application of nuclear technology, many large area contamination detectors are used to measure the contaminated surface by α, β radionuclides in nuclear facilities and isotope production places. To solve the

  7. Preparing Informal Bay Area Educators for Climate Education Success

    Science.gov (United States)

    Romero, M.

    2016-12-01

    The Bay Area Climate Literacy Impact Collaborative (Bay-CLIC) joins informal science educators from over 30 environmental education organizations with the common goal of increasing climate literacy and action. Over this past year, the collaborative has been gathering existing tools and resources that will allow informal educators in the Bay Area to communicate on climate change with confidence. Bay-CLIC's work plans to bring climate science to life by equipping educators with climate data that resonates best with local audiences, which is data that is place-based and personal. Bay-CLIC is also researching effective sustainability campaigns focused on behavior change that can be crafted to fit our unique regional context and rolled out across multiple Bay-CLIC member organizations. This session will focus on sharing our findings from our six month information gathering phase. The overarching discussion will focus on the needs that Bay Area educators identified as necessary to address in order for them to provide the best quality climate education programming. We will also discuss the data we gathered on what local educators are already using in their work and share out on how this diverse array of informal educators will be implementing our research into their programs.

  8. Preparation of Zirconia-Ceria Powders with High Specific Surface Area

    Institute of Scientific and Technical Information of China (English)

    Wang Enguo; Mei Fang

    2004-01-01

    Zirconia-ceria mixed oxide powders were prepared by high temperature aging method.The effects of the temperature and the time of aging, cerium content and calcination on powder performance were studied.The result shows that high temperature aging is an efficient way of preparation of ZrO2-CeO2 mixed oxide powders with high specific surface area and good thermal stability, and that addition of a small amount of cerium to hydrous zirconia can promote the preparation of high specific surface area powders.

  9. 40 CFR Table 1 to Subpart Ddddddd... - Applicability of General Provisions to Prepared Feeds Manufacturing Area Sources

    Science.gov (United States)

    2010-07-01

    ... Prepared Feeds Manufacturing Area Sources 1 Table 1 to Subpart DDDDDDD of Part 63 Protection of Environment... Pollutants for Area Sources: Prepared Feeds Manufacturing Pt. 63, Subpt. DDDDDDD, Table 1 Table 1 to Subpart DDDDDDD of Part 63—Applicability of General Provisions to Prepared Feeds Manufacturing Area Sources...

  10. Simple room-temperature preparation of high-yield large-area graphene oxide.

    Science.gov (United States)

    Huang, N M; Lim, H N; Chia, C H; Yarmo, M A; Muhamad, M R

    2011-01-01

    Graphene has attracted much attention from researchers due to its interesting mechanical, electrochemical, and electronic properties. It has many potential applications such as polymer filler, sensor, energy conversion, and energy storage devices. Graphene-based nanocomposites are under an intense spotlight amongst researchers. A large amount of graphene is required for preparation of such samples. Lately, graphene-based materials have been the target for fundamental life science investigations. Despite graphene being a much sought-after raw material, the drawbacks in the preparation of graphene are that it is a challenge amongst researchers to produce this material in a scalable quantity and that there is a concern about its safety. Thus, a simple and efficient method for the preparation of graphene oxide (GO) is greatly desired to address these problems. In this work, one-pot chemical oxidation of graphite was carried out at room temperature for the preparation of large-area GO with ~100% conversion. This high-conversion preparation of large-area GO was achieved using a simplified Hummer's method from large graphite flakes (an average flake size of 500 μm). It was found that a high degree of oxidation of graphite could be realized by stirring graphite in a mixture of acids and potassium permanganate, resulting in GO with large lateral dimension and area, which could reach up to 120 μm and ~8000 μm(2), respectively. The simplified Hummer's method provides a facile approach for the preparation of large-area GO.

  11. Synthetic process for preparation of high surface area electroactive compounds for battery applications

    Energy Technology Data Exchange (ETDEWEB)

    Evenson, Carl; Mackay, Richard

    2013-07-23

    A process is disclosed for the preparation of electroactive cathode compounds useful in lithium-ion batteries, comprising exothermic mixing of low-cost precursors and calcination under appropriate conditions. The exothermic step may be a spontaneous flameless combustion reaction. The disclosed process can be used to prepare any lithium metal phosphate or lithium mixed metal phosphate as a high surface area single phase compound.

  12. Effect of preparation surface area on the clinical outcome of full veneer crowns in dogs.

    Science.gov (United States)

    Riehl, Jessica; Soukup, Jason W; Collins, Caitlyn; Siverling, Sarah; Ploeg, Heidi-Lynn; Snyder, Christopher J

    2014-01-01

    Crown therapy is commonly used in veterinary medicine to provide support to teeth which have previously fractured, received root canal therapy, have significant wear, or experienced other detrimental removal of tooth substance. As with several aspects of veterinary medicine, many of the recommendations or guidelines for crown therapy originate from human dentistry, which are then transferred to veterinary patients. Due to the significant difference in the anatomy of teeth and function of the oral cavity between humans and dogs, these guidelines need to be studied to determine the appropriateness of their use in veterinary patients. This article evaluates the relationship between surface area of the preparation and clinical outcome of full veneer crown therapy of the canine tooth in dogs. Although there appeared to be a positive relationship between preparations with greater surface area and successful clinical outcome, it was not found to be statistically significant.

  13. A simple and highly effective process for the preparation of activated carbons with high surface area

    Energy Technology Data Exchange (ETDEWEB)

    Li Ying, E-mail: liyingjlu@163.com [College of Chemistry, Jilin University, Changchun 130012 (China); Ding Xuefeng; Guo Yupeng; Wang Lili; Rong Chunguang; Qu Yuning; Ma Xiaoyu [College of Chemistry, Jilin University, Changchun 130012 (China); Wang Zichen, E-mail: wangzc@jlu.edu.cn [College of Chemistry, Jilin University, Changchun 130012 (China)

    2011-06-15

    Highlights: {yields} High surface area activated carbon can be prepared by rice husk H{sub 3}PO{sub 4} without pretreatment. {yields} The characteristics of the activated carbon were greatly influenced by post-processing method. {yields} The lower SiO{sub 2} content of the activated carbons, the higher pore volume the carbons had. {yields} Some silica in rice husk reacted with H{sub 3}PO{sub 4} to form SiP{sub 2}O{sub 7} which could be removed by post-process. - Abstract: Activated carbons with high surface area were prepared by phosphoric acid as activation agent and rice husks as precursors. It was found that the characteristics of the activated carbons were influenced not only by the preparation but also by the post-processing method. The high surface area of the activated carbons was prepared under the optimum condition (50% H{sub 3}PO{sub 4} with impregnation ratio of 5:1, activation temperature of 500 deg. C, activation time of 0.5 h, wash water temperature of 100 deg. C). SiO{sub 2} content could affect the surface area of activated carbons, either. The lower SiO{sub 2} content of the activated carbons, the higher pore volume the carbons had. The SiO{sub 2} content was 11.2% when used the optimum condition. The explanation was that silicon element in rice husks reacted with H{sub 3}PO{sub 4} to form silicon phosphate (SiP{sub 2}O{sub 7}), and it could be proved further by X-ray diffraction analysis, SiP{sub 2}O{sub 7} could be removed by post-process.

  14. Preparation and Characterization of Porous Yttrium Oxide Powders with High Specific Surface Area

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The porous cubic yttrium oxides with high specific surface area were prepared by the explosive decomposition of yttrium nitrate and its complex formed with methyl salicylate. The specific surface area and properties of powders synthesized at various temperatures were characterized using BET, X-ray diffraction (XRD), infrared spectra (IR), and scanning electron microscopy (SEM). The results indicate that the highest specific surface area is found to be 65.37 m2*g-1 at the calcination temperature of 600 ℃, and then decreases to 20.33 m2*g-1 with the calcination temperature rising from 600 to 900 ℃. The powders show strong surface activity for adsorping water and carbon dioxide in air, which also decreases with the rising calcination temperature. The drop both on the surface area and surface activity of samples at higher temperatures may be due to pore-narrowing(sintering) effects.

  15. Influence of retentive areas associated to onlay preparations on the dimensional stability of silicone impression materials.

    Science.gov (United States)

    Yatsuda, Regis A; Lima, Adriano F; Yatsuda, Regiane; Cavalcanti, Andrea N; Capp, Cláudia I; Novelli, Moacyr D; de Cara, Antonio A

    2010-01-01

    This study evaluated the effect of retentive areas on onlay preparations on the dimensional alterations in condensation and addition silicone materials. A standard model with an onlay preparation was made. Each impression material was used through the double or simultaneous impression technique (n=25), resulting in a hundred impressions of the same model. Impressions were poured with type IV dental stone. Digital images were taken with a light microscope and the distances between the reference points created on the plaster dies were compared with the ones on the standard model. In the occlusal, mesial-medium and mesial-cervical segments, the double impression (DI) with condensation silicone presented similar values compared to the standard model. The values of the addition silicone with DI were similar to the standard model only in the mesial-occlusal segment. In the other segments (distal-cervical, distal-medium and distal-occlusal), all groups were statistically different from the control. It could be concluded that addition and condensation silicone impressions provided plaster dies with significant dimensional alterations in most of the evaluated areas when compared to the standard model. The retentive areas related to the onlay preparation influenced the dimensional stability of the addition and condensation silicone impressions.

  16. Method for the preparation of high surface area high permeability carbons

    Science.gov (United States)

    Lagasse, R.R.; Schroeder, J.L.

    1999-05-11

    A method for preparing carbon materials having high surface area and high macropore volume to provide high permeability. These carbon materials are prepared by dissolving a carbonizable polymer precursor, in a solvent. The solution is cooled to form a gel. The solvent is extracted from the gel by employing a non-solvent for the polymer. The non-solvent is removed by critical point drying in CO{sub 2} at an elevated pressure and temperature or evaporation in a vacuum oven. The dried product is heated in an inert atmosphere in a first heating step to a first temperature and maintained there for a time sufficient to substantially cross-link the polymer material. The cross-linked polymer material is then carbonized in an inert atmosphere. 3 figs.

  17. Method for the preparation of high surface area high permeability carbons

    Energy Technology Data Exchange (ETDEWEB)

    Lagasse, Robert R. (Albuquerque, NM); Schroeder, John L. (Albuquerque, NM)

    1999-05-11

    A method for preparing carbon materials having high surface area and high macropore volume to provide high permeability. These carbon materials are prepared by dissolving a carbonizable polymer precursor, in a solvent. The solution is cooled to form a gel. The solvent is extracted from the gel by employing a non-solvent for the polymer. The non-solvent is removed by critical point drying in CO.sub.2 at an elevated pressure and temperature or evaporation in a vacuum oven. The dried product is heated in an inert atmosphere in a first heating step to a first temperature and maintained there for a time sufficient to substantially cross-link the polymer material. The cross-linked polymer material is then carbonized in an inert atmosphere.

  18. High surface area activated carbon prepared from cassava peel by chemical activation.

    Science.gov (United States)

    Sudaryanto, Y; Hartono, S B; Irawaty, W; Hindarso, H; Ismadji, S

    2006-03-01

    Cassava is one of the most important commodities in Indonesia, an agricultural country. Cassava is one of the primary foods in our country and usually used for traditional food, cake, etc. Cassava peel is an agricultural waste from the food and starch processing industries. In this study, this solid waste was used as the precursor for activated carbon preparation. The preparation process consisted of potassium hydroxide impregnation at different impregnation ratio followed by carbonization at 450-750 degrees C for 1-3 h. The results revealed that activation time gives no significant effect on the pore structure of activated carbon produced, however, the pore characteristic of carbon changes significantly with impregnation ratio and carbonization temperature. The maximum surface area and pore volume were obtained at impregnation ratio 5:2 and carbonization temperature 750 degrees C.

  19. Preparation and characterization of boron nitride/carbon fiber composite with high specific surface area

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Yan; Fan, Mingwen [Wuhan Univ. (China). Key Laboratory for Oral Biomedical Engineering; Yuan, Songdong; Xiong, Kun; Hu, Kunpeng; Luo, Yi [Hubei Univ. of Technology, Wuhan (China). School of Chemistry and Chemical Engineering; Li, Dong [Hubei Univ. of Technology, Wuhan (China). School of Chemistry and Chemical Engineering; Oxford Univ. (United Kingdom). Chemistry Research Lab.

    2014-06-15

    Boron nitride can be used as a good catalyst carrier because of its high thermal conductivity and chemical stability. However, a high specific surface area of boron nitride is still desirable. In this work, a carbon fiber composite coated with boron nitride villous nano-film was prepared, and was also characterized by means of scanning electron microscopy, high resolution transmission electron microscopy, Fourier transform infrared spectroscopy, and Brunauer-Emmett-Teller analysis. The results indicated that the carbon fibers were covered by uniform villous boron nitride films whose thickness was about 150 - 200 nm. The specific surface area of the boron nitride/carbon fiber composite material was 96 m{sup 2} g{sup -1}, which was markedly improved compared with conventional boron nitride materials. (orig.)

  20. Development of Inspection and Investigation Techniques to Prepare Debris Flow in Urban Areas

    Science.gov (United States)

    Seong, Joo-Hyun; Jung, Min-Hyeong; Park, Kyung-Han; An, Jai-Wook; Kim, Jiseong

    2017-04-01

    Due to the urban development, various facilities are located in mountainous areas near the city, and the damage to the occurrence of the debris flow is increasing in the urban area. However, quantitative inspection and investigation techniques are not sufficient for preparing debris flow in the urban area around the world. Therefore, in this study, we developed the debris flow inspection and investigation techniques, which are suitable for urban characteristics, regarding the soil hazard prevention and restoration in urban area. First, the inspection and investigation system is divided into the daily occurrence and the occurrence of the soil hazard event, and the inspection / investigation flow chart were developed based on the kind of inspection and correspondence required for each situation. The types of inspections applied in this study were determined as daily inspection, regular inspections, special emergency inspection, damage emergency inspection and In-depth safety inspection. The management agency, term of inspection, objects to be inspected, and contents of inspection work were presented according to type of each inspection. The daily inspection routinely checks for signs of collapse and conditions of facilities in urban areas which show vulnerability for soil hazard and that are conducted from the management agency. In the case of regular inspection, an expert for soil hazards regularly conducts detailed visual surveys on mountainous areas, steep slopes, prevention facilities and adjacent facilities in vulnerable areas. On the other hand, it was decided that the emergency inspection is carried out in the event of the occurrence of vulnerable element or soil hazards. Acknowledgement This study was conducted with the research iund support by the constructiontechnology research project of the Ministry of Land, Infrastructure and Transport (project number 16SCIP-B069989-04)

  1. Preparation of High Surface Area, Large Pore Volume Alumina by Using β-Cyclodextrin as a Non-surfactant Template

    Institute of Scientific and Technical Information of China (English)

    Lai Jun WANG; Ming Fen WEN; Yu Shan LI; Dong YANG; Jing CHEN; Chong Li SONG

    2006-01-01

    A series of alumina samples were prepared using β-cyclodextrin as the non-surfactant template. These samples were characterized by XRD, BET and TEM. The results showed that the alumina samples prepared using β-cyclodextrin template had the higher surface areas (124-484 m2/g), larger pore volumes (0.7-1.27 mL/g) and more thermal stability than samples prepared without using β-cyclodextrin.

  2. Preparation

    Directory of Open Access Journals (Sweden)

    M.M. Dardir

    2014-03-01

    Full Text Available Some hexanamide-mono and di-linoleniate esters were prepared by the reaction of linolenic acid and hexanamide (derived from the reaction of hexanoic acid and diethanolamine. The chemical structure for the newly prepared hexanamide-mono and di-linoleniate esters were elucidated using elemental analysis, (FTIR, H 1NMR and chemical ionization mass spectra (CI/Ms spectroscopic techniques. The results of the spectroscopic analysis indicated that they were prepared through the right method and they have high purity. The new prepared esters have high biodegradability and lower toxicity (environmentally friendly so they were evaluated as a synthetic-based mud (ester-based mud for oil-well drilling fluids. The evaluation included study of the rheological properties, filtration and thermal properties of the ester based-muds formulated with the newly prepared esters compared to the reference commercial synthetic-based mud.

  3. Preparation and Characterization of Highly Spherical Silica-titania Aerogel Beads with High Surface Area

    Directory of Open Access Journals (Sweden)

    YU Yu-xi

    2017-02-01

    Full Text Available The silica-titania aerogel beads were synthesized through sol-gel reaction followed by supercritical drying, in which TEOS and TBT as co-precursors, EtOH as solvents, HAC and NH3·H2O as catalysts. The as-prepared aerogel beads were characterized by SEM,TEM,XRD,FT-IR,TG-DTA and nitrogen adsorption-desorption. The results indicate that the diameter distribution of beads are between 1-8mm, the average diameter of beads is 3.5mm. The aerogel beads have nanoporous network structure with high specific surface area of 914.5m2/g, and the TiO2 particles are distributed in the aerogel uniformly, which keep the anatase crystal under high temperature.

  4. Improved Cellulose Adsorption Method for the Preparation of Perovskite Oxides with Large Specific Surface Area at Low Temperature

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Perovskite-type La1-xSrxMO3-d (x=0,0.1,0.2, B=Co,Fe,Mn) oxides were prepared by pyrolysis of metal salt-(organic acid)-cellulose compound precursors. Low calcination temperatures, usually lower than 600oC, were needed. The specific surface area of the as-prepared oxides is higher than that prepared by the cellulose adsorption method, and is comparable to that prepared by sol-gel method. The effective organic acid could be EDTA acid, citric acid or DL-hydroxysuccinic acid, among them, EDTA acid is the best one.

  5. n-Alkylamine-assisted preparation of a high surface area vanadyl phosphate/tetraethylorthosilicate nanocomposite

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, João Paulo L., E-mail: billbrujah@yahoo.com.br [Departamento de Química, Faculdade de Filosofia, Ciências e Letras de Ribeirão Preto, Universidade de São Paulo, Av. Bandeirantes 3900, Ribeirão Preto, SP 14040-901 (Brazil); Zampronio, Elaine C.; Oliveira, Herenilton P. [Departamento de Química, Faculdade de Filosofia, Ciências e Letras de Ribeirão Preto, Universidade de São Paulo, Av. Bandeirantes 3900, Ribeirão Preto, SP 14040-901 (Brazil)

    2013-02-15

    Graphical abstract: CuK{sub α} X-ray diffraction patterns of the VP, VPOc, VPOcT, VPOcT200 and VPOcT500. Highlights: ► TEOS and octylamine incorporation into the VP was achieved by expanding the lamellar. ► The specific surface area increased from 15 m{sup 2} g{sup −1} in VP to 237 m{sup 2} g{sup −1} in VPOcT. ► The VPOcT exhibited thermal resistance up to 200 °C in air. ► Upon thermal treatment up to 500 °C, the surface area increased to 838 m{sup 2} g{sup −1}. -- Abstract: We have developed a vanadyl phosphate/tetraethylorthosilicate (VPO/TEOS) nanocomposite comprised of silicate chains interleaved with VPO layers, prepared by using an n-alkylamines such as octylamine as the structure directing agent. The nanocomposites were synthesized by reacting amine-intercalated vanadyl phosphate with tetraethylorthosilicate via the soft chemistry approach. The synthetic procedure encompassed the exfoliation of the layered vanadyl phosphate as well as the reorganization of this exfoliated solid into a mesostructured lamellar phase with the same V–P–O connectivity as in the original matrix. TEOS incorporation into the vanadyl phosphate was achieved by expanding the lamellar structure with n-alkylamine (Δd = 13 Å with n-octylamine). The specific surface area increased from 15 m{sup 2} g{sup −1} in the vanadyl phosphate matrix to 237 m{sup 2} g{sup −1} in VPOcT, and the isotherm curves revealed the characteristic hysteresis of mesoporous materials. Upon thermal treatment up to 500 °C, the surface area increased to 837 m{sup 2} g{sup −1}, which is suitable for catalytic purposes.

  6. Fluid regime in the source and preparation area of an earthquake

    Science.gov (United States)

    Kissin, I. G.

    2016-09-01

    Peculiarities of the fluid regime in the source and in the area of preparation of an earthquake which accommodates the evolution of the precursors are considered. The qualitative characteristics and the conditions of migration of the fluids, as well as their influence on the disjunctive deformations of the crust are discussed. During the development of the earthquake source, the fluid regime in this area depends on the redistribution of the fluids and their inflow from the outside. The fluid inflow and the increase in the fluid pressure are mainly due to the filtering from the subvertical permeable faults and the metamorphic dehydration of the rocks in the walls of the main fault. The fluids may also be supplied to the source from the near-surface horizons, and most of the induced earthquakes are associated with this process. These earthquakes can be considered as large-scale natural experiments which can shed light on the contribution of fluids in this phenomenon. A particular role in the mechanism of natural seismicity is played by the inflow of high-pressure fluids through the faults from the deep zones of the section.

  7. Preparation and Characterization of High Surface Area Activated Carbon Fibers from Lignin

    Directory of Open Access Journals (Sweden)

    Jian Lin

    2016-10-01

    Full Text Available Activated carbon fibers (ACFs were successfully prepared from softwood lignin, which was isolated with polyethylene glycol 400 (PEG-400 as a solvolysis reagent, by water steam activation. The pore characterization and adsorption property of ACFs were investigated. The results showed that all the ACFs with more micropores exhibited high specific surface area and total pore volume which increased with the activation time prolonging; the highest ones were around 3100 m2/g and 1.5 mL/g, respectively. The specific surface area and total pore volume were much larger than those of other types of lignin-based ACFs and activated charcoal. Besides, with increasing activation time, the amount of graphitic carbon, which was the main compound on the surface of ACFs, decreased, while the amount of functional groups containing C–O slightly increased. In addition, the adsorption capacity of ACFs for methylene blue was highly increased as the activation time increased. Accordingly, lignin isolated with PEG is a promising precursor for ACF production.

  8. [Preparation of large area Al-ZnO thin film by DC magnetron sputtering].

    Science.gov (United States)

    Jiao, Fei; Liao, Cheng; Han, Jun-Feng; Zhou, Zhen

    2009-03-01

    Solar cells of p-CIS/n-buffer/ZnO type, where CIS is (CuInS2, CuInSe2 or intermediates, are thin-film-based devices for the future high-efficiency and low-cost photovoltaic devices. As important thin film, the properties of Al-doped ZnO (AZO) directly affect the parameter of the cell, especially for large volume. In the present paper, AZO semiconductor transparent thin film on soda-lime glass was fabricated using cylindrical zinc-aluminum target, which can not only lower the cost of the target but also make the preparation of large area AZO thin film more easily. Using the DC magnet sputtering techniques and rolling target, high utilization efficiency of target was achieved and large area uniform and directional film was realized. An introduction to DC magnet sputtering techniques for large area film fabrication is given. With different measurement methods, such as X-ray diffraction (XRD) and scan electron microscope (SEM), we analyzed large size film's structure, appearance, and electrical and optical characteristics. The XRD spectrum indicated that the AZO film shows well zinc-blende structure with a preferred (002) growth and the c-axis is oriented normal to the substrate plane. The lattice constant is 5.603 9 nm and the mismatch with CdS thin film is only 2 percent. It absolutely satisfied the demand of the GIGS solar cell. The cross-section of the AZO thin film indicates the columnar structure and the surface morphology shows that the crystal size is about 50 nm that is consistent with the result of XRD spectrum. By the optical transmission curve, not only the high transmission rate over 85 percent in the visible spectrum between 400 nm and 700 nm was showed but also the band gap 3.1 eV was estimated. And all these parameters can meet the demand of the large area module of GIGS solar cell. The result is that using alloy target and Ar gas, and controlling the appropriate pressure of oxygen, we can get directional, condensed, uniform, high transmitting rate, low

  9. Uniformity in large area ZnO:Al films prepared by reactive midfrequency magnetron sputtering

    CERN Document Server

    Hong, R J; Sittinger, V; Szyszka, B; Hoeing, T; Bräuer, G; Heide, G; Frischat, G H

    2002-01-01

    Al-doped zinc oxide (ZnO:Al) films were deposited on glass substrates using a reactive midfrequency magnetron sputtering process. The optical transmission and reflection as well as the electrical resistivity of the films prepared on an area of 1000x600 mm sup 2 were determined at different locations. Films with a uniform distribution of resistivity between 2.9x10 sup - sup 4 and 3.6x10 sup - sup 4 OMEGA cm and transmittance up to 88% in the visible spectral range were obtained. The ellipsometric spectra of the films were also analyzed using the Drude-Lorentz model. The calculated thicknesses of the films agreed well with those measured by a step profilometer. Secondary neutral mass spectrometry depth profiling showed uniform contents of Zn and O elements, while a slight periodic variation of the Al content was observed at different depths inside the film. A transition zone of 35-55 nm in width between the films and glass substrates due to the interdiffusion was also observed.

  10. 76 FR 80314 - National Emission Standards for Hazardous Air Pollutants: Area Source Standards for Prepared...

    Science.gov (United States)

    2011-12-23

    ..., prepared Manufacturing. (except dog and cat), manufacturing. 1 North American Industry Classification... power and responsibilities among the various levels of government, as specified in Executive Order...

  11. 76 FR 80261 - National Emission Standards for Hazardous Air Pollutants: Area Source Standards for Prepared...

    Science.gov (United States)

    2011-12-23

    ..., prepared Manufacturing. (except dog and cat), manufacturing. \\1\\ North American Industry Classification... government and the states, or on the distribution of power and responsibilities among the various levels...

  12. Morphological Study Of Border Area Of Pulp-Capping Materials And Er:YAG Laser Prepared Hard Dental Surface.

    Science.gov (United States)

    Stefanova, Vessela P; Tomov, Georgi T; Tsanova, Snezhana Ts

    2015-01-01

    Vital pulp therapy involves biologically based therapeutic activities aimed at restoring health and preserving the vitality of cariously or traumatically damaged pulp. Adaptation of pulp-capping materials to the prepared tooth surface may be the key to the success of biological tooth treatment. To investigate the area of adaptation of synthetic tricalcium silicate cement, calcium hydroxide cement and mineral trioxide-aggregate to the dentin surface, prepared with the help of Er:YAG dental laser. Four extracted human tooth cavities were prepared with the help of Er:YAG dental laser (LiteTouch, Syneron, Israel), establishing microcommunication with the pulp chamber less than 1 mm in diameter. As pulp-capping materials in the cavities we used tricalcium silicate cement (Biodentine, Septodont, France), calcium hydroxide cement (Dycal) and mineral-trioxide aggregate (ProRoot MTA), stirred and administered according to manufacturers' instructions. The first material fills the whole cavity and the other two are spread in a thin layer and sealed with glass ionomer cement. Thus prepared, the samples were left for three days at 37°C in humidified environment. The samples were prepared for scanning electron microscopy (SEM) by standard methodology. The border area surfaces of the materials and the dentin were scanned using electron microscopy. The morphological changes occurring to the Er:YAG laser prepared dentin and the structural characteristics of the studied pulp-capping materials are demonstrated using scanograms. The border areas where good contact of materials and dentinal tubules is established are thoroughly studied. Good adaptation is seen in three-calcium silicate cement, followed by mineral trioxide aggregate and calcium hydroxide cement. The dentin surface, prepared with Er:YAG laser demonstrates a very good adaptation of the three tested pulp-capping materials.

  13. 75 FR 57051 - Notice of Intent To Prepare a Draft Environmental Impact Statement for the Sunset Area Community...

    Science.gov (United States)

    2010-09-17

    ... Environmental Impact Statement (EIS) for the redevelopment of the Sunset Terrace public housing community and... URBAN DEVELOPMENT Notice of Intent To Prepare a Draft Environmental Impact Statement for the Sunset Area...; environmental justice; historic/cultural resources; housing; land use; noise; parks and recreation; plants...

  14. 76 FR 33341 - Notice of Intent to prepare a Resource Management Plan for the West Eugene Wetlands Planning Area...

    Science.gov (United States)

    2011-06-08

    ... costs of management. Preliminary planning criteria include: 1. Lands addressed in the RMP will be public... Bureau of Land Management Notice of Intent to prepare a Resource Management Plan for the West Eugene Wetlands Planning Area in the State of Oregon and Associated Environmental Impact Statement AGENCY: Bureau...

  15. Microwave assisted hydrolysis of aluminium metal and preparation of high surface area Al2O3 powder

    Indian Academy of Sciences (India)

    A K Sivadasan; I Packia Selvam; Sankara Narayanan Potty

    2010-12-01

    Phase pure boehmite particles were prepared by microwave assisted hydrolysis of aluminium sheets. These particles were calcined in air to produce Al2O3 particles with specific surface area of ∼210 m2/g. The alumina particles were characterized by studying X-ray diffraction, transmission electron microscopy and Fourier transform infrared spectroscopy. For comparison, the aluminium hydroxide particles were also prepared by normal hydrolysis of aluminium metal. Normal hydrolysis yielded a mixture of boehmite and bayerite particles whereas microwave assisted hydrolysis produced phase pure boehmite particles. The importance of using microwave radiation for the hydrolysis of aluminium metal is also manifested in a shorter reaction time.

  16. Preparing Content Area Teachers for Disciplinary Literacy Instruction: The Role of Literacy Teacher Educators

    Science.gov (United States)

    Fang, Zhihui

    2014-01-01

    The recent call for secondary reading instruction to move away from a focus on generic literacy strategies to discipline-specific language and literacy practices presents new challenges for secondary teacher preparation. This column identifies some of the roles literacy teacher educators can play in helping address these challenges.

  17. Canal Transportation, Unprepared Areas, and Dentin Removal after Preparation with BT-RaCe and ProTaper Next Systems.

    Science.gov (United States)

    Brasil, Sabrina C; Marceliano-Alves, Marília F; Marques, Márcia L; Grillo, João P; Lacerda, Mariane F L S; Alves, Flávio R F; Siqueira, José F; Provenzano, José C

    2017-07-13

    This study compared the shaping ability of ProTaper Next (Dentsply Sirona, Tulsa, OK) and BT-RaCe (FKG Dentaire, La Chaux-de-Fonds, Switzerland) instrument systems in the mesial canals of mandibular molars using micro-computed tomographic (micro-CT) imaging. A total of 17 type IV mesial roots of extracted first mandibular molars were scanned using micro-CT imaging before and after root canal preparation with the 2 instrument systems. Both systems were used in the same root but alternating the mesial canals from root to root. The following parameters were analyzed: root canal volume, surface area, unprepared surface areas, transportation, canal/root width ratio, and preparation time. There were no statistically significant differences between the 2 systems for all evaluated parameters (P > .05). The unprepared surface areas for the full canal length and the apical 5-mm segment were 33% and 14% for BT-RaCe and 31% and 14% for ProTaper Next, respectively. After preparation, all root canals had a diameter that was not larger than 35% of the root diameter at the coronal and middle segments. The 2 systems showed no differences in any of the evaluated shaping parameters. None of the tested systems put the roots at risk of fracture because of excessive dentin removal. Copyright © 2017 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  18. Space-confined preparation of high surface area tungsten oxide and tungsten nitride inside the pores of mesoporous silica SBA-15

    DEFF Research Database (Denmark)

    Meyer, Simon; Beyer, Hans; Köhler, Klaus

    2015-01-01

    For the direct preparation of high surface area nitride materials, a lack of suitable precursors exists. Indirect preparation by gas phase nitridation (e.g. by ammonia) requires high temperatures and often results in sintering. The present work demonstrates that the space-confined preparation of ...

  19. Non-home prepared foods : contribution to energy and nutrient intake of consumers living in two low-income areas in Nairobi

    NARCIS (Netherlands)

    Riet, van 't H.; Hartog, den A.P.; Staveren, van W.A.

    2002-01-01

    Objective: To determine the nutritional importance of non-home prepared foods for men, women and schoolchildren living in two low-income residential areas of Nairobi, and the sources of these non-home prepared foods. Design, setting and subjects: A survey was conducted in Korogocho, a slum area, and

  20. Preparation of High-Surface Area Nano-CeO2 by Template-Assisted Precipitation Method

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The high-surface area nano-CeO2 was prepared by Ce(NO3)3 by precipitation method, with surfactant cetyltrimethyl ammonium bromide (CTAB) as templating agent. The effects of the precipitating agents, reaction temperature, ageing time, and calcination temperature on the surface area, as well as the pore structure and the mean crystallite size of nano-CeO2 were studied. It was found that the reaction of Ce(NO3)3 with NaOH in the presence of CTAB at 90 ℃ for 12 h yieldsed a cerium oxide/surfactant mixture, which after calcination at 400 ℃ resulted in high-surface area nano-CeO2. The mean crystallite size of CeO2 was approximately 6 nm, surface area was in excess of 200 m2·g-1, pore size was approximately 9 nm, and the pore distribution was concentrative. Moreover, the surface area can still reach 147 m2·g-1 after calcination at 700 ℃, which showed the good thermal stability of the CeO2. The number of oxygen vacancies in the structure of CeO2 corresponded with the surface area of CeO2, and the high surface area was propitious to the formation of oxygen vacancies.

  1. Characteristics and Laser Performance of Yb3+-Doped Silica Large Mode Area Fibers Prepared by Sol–Gel Method

    Directory of Open Access Journals (Sweden)

    Shikai Wang

    2013-12-01

    Full Text Available Large-size 0.1 Yb2O3–1.0 Al2O3–98.9 SiO2 (mol% core glass was prepared by the sol–gel method. Its optical properties were evaluated. Both large mode area double cladding fiber (LMA DCF with core diameter of 48 µm and large mode area photonic crystal fiber (LMA PCF with core diameter of 90 µm were prepared from this core glass. Transmission loss at 1200 nm is 0.41 dB/m. Refractive index fluctuation is less than 2 × 10−4. Pumped by 976 nm laser diode LD pigtailed with silica fiber (NA 0.22, the slope efficiency of 54% and “light-to-light” conversion efficiency of 51% were realized in large mode area double cladding fiber, and 81 W laser power with a slope efficiency of 70.8% was achieved in the corresponding large mode area photonic crystal fiber.

  2. Method for the Preparation of Hazard Map in Urban Area Using Soil Depth and Groundwater Level

    Science.gov (United States)

    Kim, Sung-Wook; Choi, Eun-Kyeong; Cho, Jin Woo; Lee, Ju-Hyoung

    2017-04-01

    The hazard maps for predicting collapse on natural slopes consists of a combination of topographic, hydrological, and geological factors. Topographic factors are extracted from DEM, including aspect, slope, curvature, and topographic index. Hydrological factors, such as distance to drainage, drainage density, stream-power index, and wetness index are most important factors for slope instability. However, most of the urban areas are located on the plains and it is difficult to apply the hazard map using the topography and hydrological factors. In order to evaluate the risk of collapse of flat and low slope areas, soil depth and groundwater level data were collected and used as a factor for interpretation. In addition, the reliability of the hazard map was compared with the disaster history of the study area (Gangnam-gu and Yeouido district). In the disaster map of the disaster prevention agency, the urban area was mostly classified as the stable area and did not reflect the collapse history. Soil depth, drainage conditions and groundwater level obtained from boreholes were added as input data of hazard map, and disaster vulnerability increased at the location where the actual collapse points. In the study area where damage occurred, the moderate and low grades of the vulnerability of previous hazard map were 12% and 88%, respectively. While, the improved map showed 2% high grade, moderate grade 29%, low grade 66% and very low grade 2%. These results were similar to actual damage. Keywords: hazard map, urban area, soil depth, ground water level Acknowledgement This research was supported by a Grant from a Strategic Research Project (Horizontal Drilling and Stabilization Technologies for Urban Search and Rescue (US&R) Operation) funded by the Korea Institute of Civil Engineering and Building Technology.

  3. Electrochemical preparation of metal microstructures on large areas of etched ion track membranes

    Science.gov (United States)

    Dobrev, D.; Vetter, J.; Angert, N.

    1999-01-01

    A microgalvanic method for metal filling of etched ion tracks in organic foils on large areas is described. The method and the used galvanic cell permit the deposition of stable standing individual metal whiskers with high aspect ratio and a density of 10 5-10 8 per cm 2 on an area of 12.5 cm 2. The method was verified with copper and it is suitable also for various other metals. It can be applied for the replication of etched ion tracks and for the fabrication of microstructures containing large numbers of individual metal whiskers.

  4. Preparation of Super-Thin, Large-Area, Double-Sided Gold-Plated Mylar Film

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    Large-area multi-wire parallel plane avalanche counter (MWPPAC) is a kind of gas detector widely used in nuclear experiments. MWPPAC is composed of front-window film, X wires, anode film, Y wires and rear-window film, which is mostly utilized to measuring

  5. Preparation, Surface and Pore Structure of High Surface Area Activated Carbon Fibers from Bamboo by Steam Activation

    Directory of Open Access Journals (Sweden)

    Xiaojun Ma

    2014-06-01

    Full Text Available High surface area activated carbon fibers (ACF have been prepared from bamboo by steam activation after liquefaction and curing. The influences of activation temperature on the microstructure, surface area and porosity were investigated. The results showed that ACF from bamboo at 850 °C have the maximum iodine and methylene blue adsorption values. Aside from the graphitic carbon, phenolic and carbonyl groups were the predominant functions on the surface of activated carbon fiber from bamboo. The prepared ACF from bamboo were found to be mainly type I of isotherm, but the mesoporosity presented an increasing trend after 700 °C. The surface area and micropore volume of samples, which were determined by application of the Brunauer-Emmett-Teller (BET and t-plot methods, were as high as 2024 m2/g and 0.569 cm3/g, respectively. It was also found that the higher activation temperature produced the more ordered microcrystalline structure of ACF from bamboo.

  6. Flow calorimetry of the sorption of butanols to elastin preparations and comparison with surface areas determined by krypton-85 adsorption.

    Science.gov (United States)

    Robert, L; Robert, B; Houtman, J P; Stack, M V

    1971-12-28

    1. The apparent surface areas of elastin samples as well as of several other fibrous protein preparations (collagen, keratin, polymeric stroma of aorta) were determined using two different approaches: (a) the Brunauer-Emmett-Teller method with 85Kr and (b) microflow calorimetry with n- and tert.-butanol as adsorbents in a heptane stream. 2. Areas of heat signals obtained by flow calorimetry for the adsorption and desorption of n- and tert.-butanol were substantially equivalent; desorption was more protracted than adsorption, the difference between the speed of desorption and adsorption increased with decreasing chain length of the alcohols (methanol, ethanol, n-propanol and n-butanol). 3. An inverse linear relationship was found between the energy change recorded during the adsorption process and the chain length of the alcohols (methanol, ethanol, n-propanol, n-butanol). 4. Heats of adsorption of tert.-butanol were systematically found to be significantly lower than those of n-butanol with all the protein samples investigated. 5. The apparent surface areas of the protein samples determined with tert.-butanol were on the average of the same order or only slightly higher than those obtained with 85Kr. Results obtained with n-butanol were significantly higher. The difference between surface areas obtained with n- and tert.-butanol depended on the nature of the protein sample, on its method of preparation and to some extent on the residual humidity of the sample. 6. The results could be explained on the basis of the hydrophobic theory of elastin structure (see ref. 4) and confirmed our former conclusions (see ref. 3) concerning the significantly higher surface areas of elastin samples purified by different procedures as compared to collagen or to keratin. They also confirmed the accessibility of the surface of elastic fibers to the molecular probes used in the polymeric stroma of aorta.

  7. Building a Capabilities Network to Improve Disaster Preparation Effort in the Pacific Command Area of Responsibility

    Science.gov (United States)

    2013-06-01

    and Community Participation.” • Microfinance – CSR’s microfinance program focus on providing training people on how to save money and provide...disasters. ú Concern Worldwide U.S. also provides training in the areas of “ microfinance products; infrastructural development, necessary to small...business generation; and business development services (BDS) in which microfinance activities are promoted to stimulate work for the poorest-who we

  8. Effect of Activating Agent on the Preparation of Bamboo-Based High Surface Area Activated Carbon by Microwave Heating

    Science.gov (United States)

    Xia, Hongying; Wu, Jian; Srinivasakannan, Chandrasekar; Peng, Jinhui; Zhang, Libo

    2016-06-01

    The present work attempts to convert bamboo into a high surface area activated carbon via microwave heating. Different chemical activating agents such as KOH, NaOH, K2CO3 and Na2CO3 were utilized to identify a most suitable activating agent. Among the activating agents tested KOH was found to generate carbon with the highest porosity and surface area. The effect of KOH/C ratio on the porous nature of the activated carbon has been assessed. An optimal KOH/C ratio of 4 was identified, beyond which the surface area as well as the pore volume were found to decrease. At the optimized KOH/C ratio the surface area and the pore volume were estimated to be 3,441 m2/g and 2.093 ml/g, respectively, with the significant proportion of which being microporous (62.3%). Activated carbon prepared under the optimum conditions was further characterized using Fourier transform infrared spectroscopy (FTIR) and scanning electron microscope (SEM). Activated carbons with so high surface area and pore volume are very rarely reported, which could be owed to the nature of the precursor and the optimal conditions of mixture ratio adopted in the present work.

  9. Preparation of Large Area Double Sided YBCO Thin Films by DC Magneton Sputtering

    Institute of Scientific and Technical Information of China (English)

    Li Tao; Gu Hongwei; Wang Peiwen; Wang Xiaoping; Xie Bowei

    2004-01-01

    Tc, Jc and Rs properties of large area double sided YBCO thin films deposited on LaAlO3 substrates by direct current sputtering were reported.Film thickness of the obtained thin films is over 300 nm, Tc > 90 K; Rs can be as low as less than 1.0 mΩ(77 K, 10 GHz).Homogenousity of the properties around the plane was studied.Under the measnous distributions.Influences of substrate temperature and Ar and O2 pressures on properties of the double-sided thin films were discussed.

  10. Sanitation in classroom and food preparation areas in child-care facilities in North Carolina and South Carolina.

    Science.gov (United States)

    Wohlgenent, Kelly C; Cates, Sheryl C; Fraser, Angela; Chapman, Benjamin; Jaykus, Lee-Ann; Chen, Xi

    2014-11-01

    Approximately 60% of U.S. children aged five and younger spend time in child-care settings. Such environments increase the risk of diarrheal disease, including diseases caused by enteric pathogens. To describe adherence to sanitation standards in classrooms and food preparation areas in child-care facilities, the authors conducted site visits in 40 North Carolina and South Carolina child-care facilities. Audits in up to two classrooms (rooms providing care for infants and toddlers) and the kitchen were performed using a form similar to a regulatory inspection form. Audit data were used to calculate indices to describe adherence to sanitation standards and were based on state environmental health regulations for child-care centers, the Food and Drug Administration's Food Code 2009, and guidance from food safety experts. Most facilities participating in the authors' study adhered to sanitation standards within the classroom; however, deficiencies with regard to sanitation in food preparation areas and refrigerator operating temperatures were noted. These results provide insight into possible risk factors for enteric disease transmission in child-care facilities.

  11. Preparing for the unprecedented - Towards quantitative oil risk assessment in the Arctic marine areas.

    Science.gov (United States)

    Nevalainen, Maisa; Helle, Inari; Vanhatalo, Jarno

    2017-01-15

    The probability of major oil accidents in Arctic seas is increasing alongside with increasing maritime traffic. Hence, there is a growing need to understand the risks posed by oil spills to these unique and sensitive areas. So far these risks have mainly been acknowledged in terms of qualitative descriptions. We introduce a probabilistic framework, based on a general food web approach, to analyze ecological impacts of oil spills. We argue that the food web approach based on key functional groups is more appropriate for providing holistic view of the involved risks than assessments based on single species. We discuss the issues characteristic to the Arctic that need a special attention in risk assessment, and provide examples how to proceed towards quantitative risk estimates. The conceptual model presented in the paper helps to identify the most important risk factors and can be used as a template for more detailed risk assessments. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

  12. High surface area ThO.sub.2 catalyst and method of preparing it

    Science.gov (United States)

    Colmenares, Carlos A.; Somorjai, Gabor A.; Maj, Joseph J.

    1985-01-01

    A ThO.sub.2 catalyst having a high surface area of about 80-125 m.sup.2 /g is synthesized. The compound is synthesized by simultaneously mixing an aqueous solution of ThNO.sub.3 (NO.sub.3).sub.4.4H.sub.2 O with an aqueous solution of Na.sub.2 CO.sub.3.H.sub.2 O, to produce a solution and solid ThOCO.sub.3. The solid ThOCO.sub.3 is separated from the solution, and then calcined at a temperature of about 225.degree.-300.degree. C. for about 40-55 hours to produce ThO.sub.2. The ThO.sub.2 catalyst produced includes Na present as a substitutional cation in an amount equal to about 5-10 atom percent.

  13. Acid/base bifunctional carbonaceous nanomaterial with large surface area: Preparation, characterization, and adsorption properties for cationic and anionic compounds

    Energy Technology Data Exchange (ETDEWEB)

    Li, Kai; Ma, Chun–Fang; Ling, Yuan; Li, Meng [Department of Chemistry, Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074 (China); Gao, Qiang, E-mail: gaoqiang@cug.edu.cn [Department of Chemistry, Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074 (China); Engineering Research Center of Nano-Geo Materials of Ministry of Education, China University of Geosciences, Wuhan 430074 (China); Luo, Wen–Jun, E-mail: heartnohome@yahoo.com.cn [Department of Chemistry, Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074 (China)

    2015-07-15

    Nanostructured carbonaceous materials are extremely important in the nano field, yet developing simple, mild, and “green” methods that can make such materials possess large surface area and rich functional groups on their surfaces still remains a considerable challenge. Herein, a one-pot and environment-friendly method, i.e., thermal treatment (180 °C; 18 h) of water mixed with glucose and chitosan (CTS), has been proposed. The resultant carbonaceous nanomaterials were characterized by field emitting scanning electron microscope, N{sub 2} adsorption/desorption, Fourier transform infrared spectroscope, X-ray photoelectron spectroscopy, and zeta-potential analysis. It was found that, in contrast to the conventional hydrothermally carbonized product from pure glucose, with low surface area (9.3 m{sup 2} g{sup −1}) and pore volume (0.016 cm{sup 3} g{sup −1}), the CTS-added carbonaceous products showed satisfactory textural parameters (surface area and pore volume up to 254 m{sup 2} g{sup −1} and 0.701 cm{sup 3} g{sup −1}, respectively). Moreover, it was also interestingly found that these CTS-added carbonaceous products possessed both acidic (–COOH) and basic (–NH{sub 2}) groups on their surfaces. Taking the advantages of large surface area and –COOH/–NH{sub 2} bifunctional surface, the carbonaceous nanomaterials exhibited excellent performance for adsorptions of cationic compound (i.e., methylene blue) at pH 10 and anionic compound (i.e., acid red 18) at pH 2, respectively. This work not only provides a simple and green route to prepare acid/base bifunctional carbonaceous nanomaterials with large surface area but also well demonstrates their potential for application in adsorption. - Highlights: • A simple and green method was proposed to prepare carbon nanomaterials. • The carbon product showed acid/base bifunctional surface with large surface area. • The carbon material could efficiently adsorb both cationic and anionic compounds.

  14. Preparation of activated carbon with high surface area for high-capacity methane storage

    Institute of Scientific and Technical Information of China (English)

    Bingsi Liua; Wenshuo Wanga; Na Wanga; Peter Chak Tong Aub

    2014-01-01

    Activated carbon (AC) was fabricated from corncob, which is cheap and abundant. Experimental parameters such as particle size of corncob, KOH/char weight ratio, and activation temperature and time were optimized to generate AC, which shows high methane sorption capacity. AC has high specific surface area (3227 m2/g), with pore volume and pore size distribution equal to 1.829 cm3/g and ca. 1.7-2.2 nm, respectively. Under the condition of 2◦C and less than 7.8 MPa, methane sorption in the presence of water (Rw=1.4) was as high as 43.7 wt%methane per unit mass of dry AC. The result is significantly higher than those of coconut-derived AC (32 wt%) and ordered mesoporous carbon (41.2 wt%, Rw=4.07) under the same condition. The physical properties and amorphous chaotic structure of AC were characterized by N2 adsorption isotherms, XRD, SEM and HRTEM. Hence, the corncob-derived AC can be considered as a competitive methane-storage material for vehicles, which are run by natural gas.

  15. Preparation and characterization of highly active nanosized strontium-doped lanthanum cobaltate catalysts with high surface areas

    Institute of Scientific and Technical Information of China (English)

    NIU Jianrong; LIU Wei; DAI Hongxing; HE Hong; ZI Xuehong; LI Peiheng

    2006-01-01

    La1-xSrxCoO3-δ (x=0, 0.4) nanoparticles have been prepared using the citric acid complexing-hydrothermal synthesis coupled method and citric acid complexing method. The physico-chemical properties of these materials were characterized by means of X-ray diffraction (XRD), high resolution scanning electron microscopy (HRSEM), element analysis (EDX), X-ray photoelectron spectroscopic (XPS), oxygen temperature-programmed desorption (O2-TPD), hydrogen temperature-programmed reduction (H2-TPR) as well as surface area measurements and oxidation state titration. Their catalytic performance was examined for the total oxidation of ethylacetate (EA). It is found that the La1-xSrxCoO3-δ (x=0, 0.4) catalysts were single-phase and rhombohedrally-structured perovskites and their surface areas ranged from 16 to 26 m2/g. The Sr-doped sample derived from the coupled procedure was uniformly distributed nanoparticles with a short rod-shaped morphology. The doping of Sr (i) enhanced the concentrations of Co3+ and oxygen vacancies, (ii) increased the amount of oxygen adsorbed on the surface at low temperatures, (iii) promoted the mobility of lattice oxygen, and (iv) improved the properties of redox. The La0.6Sr0.4CoO2.78 catalyst prepared by the citric acid complexing-hydrothermal synthesis coupled strategy performed the best in the oxidation of EA, furthermore no partially oxidized products were formed. Based on the above results, we conclude that in addition to the surface area, the catalytic activity of the perovskite-type oxide nanoparticles was associated with the structural defect (oxygen vacancy)concentration and redox ability.

  16. Effect of Preparation Method on Surface Area and Crystalline Form of CeO2-ZrO2 Solid Solution

    Institute of Scientific and Technical Information of China (English)

    王晓红; 郭耘; 卢冠忠; 郭杨龙; 王筠松; 张志刚; 刘晓晖

    2004-01-01

    The CeO2-ZrO2 solid solutions were prepared by a reverse microemulsion method. The effect of preparation parameters on the surface area and crystalline form of the solid solutions were studied by the BET surface area and XRD analysis. The studies indicate that the separation of the microemulsion phase during the preparation procedure can decrease the specific surface area of sample, adding hydrogen peroxide in the matrix solution can increase the specific surface area and stability of sample. The surface area of sample calcined at 550 ℃ for 5 h is 149 m2·g-1, and that calcined at 900 ℃ for 6 h is 88 m2·g-1.The sample with tetragonal symmetry Ce0.5Zr0.5O2 phase has a higher stability.

  17. Quantitative comparison of mathematical models to measure surface area of canine teeth prepared to receive full veneer crowns in dogs

    Directory of Open Access Journals (Sweden)

    Caitlyn eCollins

    2015-09-01

    Full Text Available Objective: This study was performed in order to determine if mathematical modeling of the canine teeth in dogs could be utilized to provide an accurate and reliable estimation of crown surface area that could be used in both a research and clinical setting.Materials and methods: Actual surface area (aSA calculations for 32 stone dies of clinical crown preparations were acquired utilizing a tridimensional (3D laser scanner and 3D computer-aided design and manufacturing (CAD/CAM software applications. These calculations were used as a control. Seventeen unique mathematical models from 8 geometric shapes were used to calculate estimated surface area (eSA of each stone die. Linear association and agreement between eSA and aSA calculations were assessed with multiple statistical methods. Results: All methods of eSA showed a significant linear association with aSA. Five of the mathematical models [right elliptical frustum (H3, right elliptical cone (G3, right pyramidal cone (A3, right circular frustum (F2 and right circular cone (E1] were superior to the other 12 models.Conclusions: The H3 mathematical model based on the right elliptical frustum provided the most accurate estimate of crown surface area of dog teeth. However, H3 requires the use of laser scans and a 3D CAD software program. As a result, this model would be recommended for research applications. The E1 mathematical model was similar in accuracy to H3 and, given it requires only two measurements and a comparatively simple equation for calculation, this method would be recommended for clinical chair-side use.

  18. Preparation of activated carbon with low ash content and high specific surface area from coal in the presence of KOH

    Institute of Scientific and Technical Information of China (English)

    XIE Qiang(解强); CHEN Qing-ru(陈清如); GONG Guo-zhuo(宫国卓); ZHANG Xiang-lan(张香兰); XU De-ping(许德平)

    2003-01-01

    An activated carbon with ash content less than 10% and specific surface area more than 1 600 m2/g was prepared from coal and the effect of K-containing compounds in preparation of coal-based activated carbon was investigated in detail in this paper. KOH was used in co-carbonization with coal, changes in graphitic crystallites in chars derived from carbonization of coal with and without KOH were analyzed by X-ray diffraction (XRD) technique, activation rates of chars with different contents of K-containing compounds were deduced, and resulting activated carbons were characterized by nitrogen adsorption isotherms at 77 K and iodine numbers. The results showed that the addition of KOH to the coal before carbonization can realize the intensive removal of inorganic matters from chars under mild conditions, especially the efficient removal of dispersive quartz, an extremely difficult separated mineral component in other processes else. Apart from this, KOH demonstrates a favorable effect in control over coal carbonization with the goal to form nongraphitizable isotropic carbon precursor, which is a necessary prerequisite for the formation and development of micro pores. However, the K-containing compounds such as K2CO3 and K2O remaining in chars after carbonization catalyze the reaction between carbon and steam in activation, which leads to the formation of macro pores. In the end an innovative method, in which KOH is added to coal before carbonization and K-containing compounds are removed by acid washing after carbonization, was proposed for the synthesis of quality coal-based activated carbon.

  19. Anti-aging Potential of Extracts Prepared from Fruits and Medicinal Herbs Cultivated in the Gyeongnam Area of Korea.

    Science.gov (United States)

    Shon, Myung-Soo; Lee, Yunjeong; Song, Ji-Hye; Park, Taehyun; Lee, Jun Kyoung; Kim, Minju; Park, Eunju; Kim, Gyo-Nam

    2014-09-01

    Many recent studies have focused on maintaining a healthy life by preventing and/or postponing the aging process. Numerous studies have reported that continuous exposure to reactive oxygen species can stimulate skin aging and that excessive accumulation of fat can cause an impaired skin barrier and tissue structure alterations. Thus, the maintenance of antioxidant homeostasis and the suppression of adipose accumulation are important strategies for skin anti-aging. Here, we prepared three types of extracts [whole juice, acetone-perchloric acid (PCA), and ethanol] from 20 fruits and medicinal herbs native to the Gyeongnam area of Korea. The total phenolic content of each extract was analyzed, and we observed higher total phenolic contents in the medicinal herbs. Consistent with this, the results of the oxygen radical absorbance activity capacity assay indicated that the in vitro antioxidant activities of the medicinal herb extracts were stronger than those of the fruit extracts. The fruits and medicinal herbs had strong effects on cell-based systems, including H2O2-induced oxidative stress in human keratinocytes and 3T3-L1 lipid accumulation. Nishimura Wase persimmon, Taishu persimmon, wrinkled giant hyssop, sweet wormwood, Chinese cedar, red perilla, tan shen, hiyodori-jogo, and cramp bark may be natural anti-aging materials with effective antioxidant and anti-adipogenic activities. Taken together, our findings may provide scientific evidence supporting the development of functional foods and nutraceuticals from fruits and medicinal herbs.

  20. Secondary sensory area SII is crucially involved in the preparation of familiar movements compared to movements never made before.

    Science.gov (United States)

    Beudel, M; Zijlstra, S; Mulder, Th; Zijdewind, I; de Jong, B M

    2011-04-01

    Secondary sensorimotor regions are involved in sensorimotor integration and movement preparation. These regions take part in parietal-premotor circuitry that is not only active during motor execution but also during movement observation and imagery. This activation particularly occurs when observed movements belong to one's own motor repertoire, consistent with the finding that motor imagery only improves performance when one can actually make such movement. We aimed to investigate whether imagery or observation of a movement that was never made before causes parietal-premotor activation or that the ability to perform this movement is indeed a precondition. Nine subjects [group Already Knowing It (AKI)] could abduct their hallux (moving big toe outward). Seven subjects initially failed to make such movement (Absolute Zero A0 group). They had to imagine, observe, or execute this movement, whereas fMRI data were obtained both before and after training. Contrasting abduction observation between the AKI-group and A0-group showed increased left SII and supplementary motor area activation. Comparing the observation of hallux flexion with abduction showed increased bilateral SII activation in the A0 and not in the AKI group. Prolonged training resulted in equal performance and similar cerebral activation patterns in the two groups. Thereby, conjunction analysis of the correlations on subject's range of abduction during execution, imagery, and observation of hallux abduction showed exclusive bilateral SII activation. The reduced SII involvement in A0 may imply that effective interplay between sensory predictions and feedback does not take place without actual movement experience. However, this can be acquired by training.

  1. A new generation of starch products as excipient in pharmaceutical tablets .1. Preparation and binding properties of high surface area potato starch products

    NARCIS (Netherlands)

    Wierik, GHPT; ArendsScholte, AW; Eissens, AC; Lerk, CF

    1996-01-01

    A new pharmaceutical excipient with a high binding capacity was prepared from potato starch by enzymatic degradation, followed by suitable dehydration of the precipitated and filtered retrograded starch to produce high specific surface area products. Thermal dehydration methods like drying at room o

  2. Preparation of High-Surface-Area SnO2 and ZrO2 by Reflux-Digestion and Solvothermal Methods

    Institute of Scientific and Technical Information of China (English)

    Ji-Ying Wei; Feng Jiang; Gang Xu; Sheng-Ming Xu

    2006-01-01

    The influence of the preparation methods on the properties of SnO2 and ZrO2 powders, especially the specific surface area and the stability upon calcination was investigated. SnO2 and ZrO2 prepared by chemical precipitation using reflux-digestion process with NaOH possess high surface area at the calcination temperature of 500℃~1000℃. A novel solvothermal process in the presence of urea was used to synthesize nanocrystalline SnO2 powders excluding the adulteration of Si. As increasing the concentration of urea, the grain size of the as-prepared powders reduced and the surface area increased.SnO2 nanocrystals with a grain size of ca. 1 nm and a high surface area of 331 m2g-1 were obtained by this method. These high-surface-area powders are favorable for gas-sensing and catalysis applications, and the development of an advanced material for structural engineering ceramics.

  3. 77 FR 17037 - Intent To Prepare a Draft Environmental Impact Statement for the Louisiana Coastal Area (LCA...

    Science.gov (United States)

    2012-03-23

    ... Louisiana Coastal Area (LCA)--Louisiana, Mississippi River Hydrodynamic and Delta Management Study AGENCY... Coastal Area (LCA)--Louisiana, Mississippi River Hydrodynamic and Delta Management restoration study. This... the Louisiana Coastal Area (LCA), Louisiana, Ecosystem Restoration Study (LCA Study). The record...

  4. Morphological Study Of Border Area Of Pulp-Capping Materials And Er:YAG Laser Prepared Hard Dental Surface

    Directory of Open Access Journals (Sweden)

    Stefanova Vessela P.

    2015-03-01

    Full Text Available Introduction: Vital pulp therapy involves biologically based therapeutic activities aimed at restoring health and preserving the vitality of cariously or traumatically damaged pulp. Adaptation of pulp-capping materials to the prepared tooth surface may be the key to the success of biological tooth treatment.

  5. Secondary Sensory Area SII is Crucially Involved in the Preparation of Familiar Movements Compared to Movements Never Made Before

    NARCIS (Netherlands)

    Beudel, M.; Zijlstra, S.; Mulder, Th.; Zijdewind, I.; de Jong, B. M.

    2011-01-01

    Secondary sensorimotor regions are involved in sensorimotor integration and movement preparation. These regions take part in parietal-premotor circuitry that is not only active during motor execution but also during movement observation and imagery. This activation particularly occurs when observed

  6. Influence of excess sodium ions on the specific surface area formation in a NiO-Al2O3 catalyst prepared by different methods

    Directory of Open Access Journals (Sweden)

    Lazić M.M.

    2008-01-01

    Full Text Available The influence of sodium ions on the specific surface area of a NiO-Al2O3 catalyst in dependence of nickel loading (5, 10, and 20 wt% Ni, temperature of heat treatment (400, 700 and 1100oC and the method of sample preparation was investigated. Low temperature nitrogen adsorption (LTNA, X-ray diffraction (XRD and scanning electron microscopy (SEM were applied for sample characterization. Dramatic differences in the specific surface area were registered between non-rinsed and rinsed Al2O3 and NiO-Al2O3 samples. The lagged sodium ions promote sintering of non-rinsed catalyst samples.

  7. Preparation of nitrogen-doped cotton stalk microporous activated carbon fiber electrodes with different surface area from hexamethylenetetramine-modified cotton stalk for electrochemical degradation of methylene blue

    Science.gov (United States)

    Li, Kunquan; Rong, Zhang; Li, Ye; Li, Cheng; Zheng, Zheng

    Cotton-stalk activated carbon fibers (CSCFs) with controllable micropore area and nitrogen content were prepared as an efficient electrode from hexamethylenetetramine-modified cotton stalk by steam/ammonia activation. The influence of microporous area, nitrogen content, voltage and initial concentration on the electrical degradation efficiency of methylene blue (MB) was evaluated by using CSCFs as anode. Results showed that the CSCF electrodes exhibited excellent MB electrochemical degradation ability including decolorization and COD removal. Increasing micropore surface area and nitrogen content of CSCF anode leaded to a corresponding increase in MB removal. The prepared CSCF-800-15-N, which has highest N content but lowest microporous area, attained the best degradation effect with 97% MB decolorization ratio for 5 mg/L MB at 12 V in 4 h, implying the doped nitrogen played a prominent role in improving the electrochemical degradation ability. The electrical degradation reaction was well described by first-order kinetics model. Overall, the aforesaid findings suggested that the nitrogen-doped CSCFs were potential electrode materials, and their electrical degradation abilities could be effectively enhanced by controlling the nitrogen content and micropore surface area.

  8. 75 FR 80799 - Preparation of the PEIS for Modernization of Training Infrastructure at Pōhakuloa Training Area, HI

    Science.gov (United States)

    2010-12-23

    ... infrastructure (roads and utilities), and training support facilities in the cantonment area at P hakuloa... PTA's long-term vision for modernizing training ranges, training support infrastructure, and the... consider modernizing the training ranges, training support infrastructure, and the cantonment area at...

  9. 76 FR 34250 - Notice of Intent To Prepare an Environmental Assessment for the Proposed Gila Lower Box Area of...

    Science.gov (United States)

    2011-06-13

    ... management to an area with significant scenic, cultural, and biological resources. The public land proposed... significant cultural resources that occur in the watershed? 3. How should the BLM address land tenure in the... recreation and tourism in the area? 9. What effects would this proposed action have on...

  10. Building a capabilities network to improve disaster preparation efforts in the European Command (EUCOM) area of responsibility

    OpenAIRE

    Daniels III, Charles E.

    2012-01-01

    Approved for public release; distribution is unlimited. United States European Commands (EUCOM) website states that the breadth of responsibility across 51 countries can factor significantly into partnering opportunities and challenges. In order to understand this responsibility, this research analyzes the capabilities of 25 non-governmental organizations in EUCOMs area of responsibility (AOR). Each organization is evaluated in six areas mission, primary focus, capabilities, religious affi...

  11. Surviving and growing of seedlings planted with their tubes in arid areas prepared with different soil cultivatıon methods

    Directory of Open Access Journals (Sweden)

    Süleyman Gülcü

    2016-04-01

    Full Text Available In this study, surviving percent and growing of seedlings planted with their tubes of Black pine [Pinus nigra Arnold. ssp. pallasiana (Lamb. Holmboe.], Taurus cedar (Cedrus libani A. Rich, Crimean juniper (Juniperus excelsa Bieb. were evaluated in the areas prepared with different soil cultivation methods for afforestation studies in arid areas. For this aim, afforestation area in Karaman disrict was selected. In the experiment, 12 treatments for land preparation by using different equipments were applied. In parcels applied these treatments, seedlings of the species were planted as tubed only cutting their 1 cm partial of bottom. The experiment was established in completely randomized plot design with three replications, 20 seedlings for each one. At the end of the second vegetation period survival rate, seedling height, growth of the terminal shoot in the last year and bottom diameter of the seedlings were measured. According to results of data analysing, minimum survival rate was 38.89% (Balck pine, maximum was 88.89% (Crimean juniper. The treatments made top soil tillage combined disc harrows and gradoni terrace applications more successful than the other treatments for all seedling characteristics and surviving percentages. In addition the treatments, double riper + gradoni terrace and triple ripper + gradoni terrace, which had better performance can suggest for soil preparetaion in arid area. Because these treatments are more practicable and cheap than the others.

  12. 78 FR 35957 - Notice of Intent To Prepare a Resource Management Plan for the Central Yukon Planning Area Alaska...

    Science.gov (United States)

    2013-06-14

    ... Planning Area Alaska and Associated Environmental Impact Statement AGENCY: Bureau of Land Management... on issues, planning criteria, and management questions and concerns related to the Central Yukon RMP... wildlife management. 8. The RMP will be consistent with the Bureau's H-1601-1 Land Use Planning Handbook...

  13. Nanocrystalline GaSbO{sub 4} with high surface area prepared via a facile hydrothermal method and its photocatalytic activity study

    Energy Technology Data Exchange (ETDEWEB)

    Fu Yanghe; Xue Hun; Qin Meng; Liu Ping; Fu Xianzhi [Research Institute of Photocatalysis, Fujian Provincial Key Laboratory of Photocatalysis - State Key Laboratory Breeding Base, Fuzhou University, Fuzhou 350002 (China); Li Zhaohui, E-mail: zhaohuili1969@yahoo.com [Research Institute of Photocatalysis, Fujian Provincial Key Laboratory of Photocatalysis - State Key Laboratory Breeding Base, Fuzhou University, Fuzhou 350002 (China)

    2012-05-05

    Graphical abstract: Nanocrystalline GaSbO{sub 4} prepared via a facile hydrothermal method possesses large specific surface area and exhibits photocatalytic activity for the degradations of salicylic acid and acetone. Highlights: Black-Right-Pointing-Pointer Facile hydrothermal method to nanocrystalline GaSbO{sub 4} with large surface area. Black-Right-Pointing-Pointer GaSbO{sub 4} shows photocatalytic activity for the degradations of salicylic acid and acetone. Black-Right-Pointing-Pointer The photocatalytic mechanism of GaSbO{sub 4} was proposed based on the ESR result. - Abstract: Nanocrystalline GaSbO{sub 4} with small particle size and large BET specific area was successfully prepared via a facile hydrothermal method from Sb{sub 2}O{sub 5}. The influence of the reaction pH on the formation of the final product was investigated. The obtained sample was characterized by X-ray diffraction (XRD), N{sub 2}-sorption BET surface area, UV-vis diffuse reflectance spectroscopy (DRS), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM). The photocatalytic activity for the degradations of salicylic acid and acetone over nanocrystalline GaSbO{sub 4} under UV irradiations was for the first time revealed. Based on the electron spin resonance (ESR) result, the reactive species involved in the photocatalytic reaction over nanocrytalline GaSbO{sub 4} are determined to be HO{center_dot} and O{sub 2}{sup -}{center_dot}. The photocatalytic mechanism of GaSbO{sub 4} was proposed.

  14. Large-area flexible monolithic ITO/WO3/Nb2O5/NiVOχ/ITO electrochromic devices prepared by using magnetron sputter deposition

    Science.gov (United States)

    Tang, Chien-Jen; Ye, Jia-Ming; Yang, Yueh-Ting; He, Ju-Liang

    2016-05-01

    Electrochromic devices (ECDs) have been applied in smart windows to control the transmission of sunlight in green buildings, saving up to 40-50% electricity consumption and ultimately reducing carbon dioxide emissions. However, the high manufacturing costs and difficulty of transportation of conventional massive large area ECDs has limited widespread applications. A unique design replacing the glass substrate commonly used in the ECD windows with inexpensive, light-weight and flexible polymeric substrate materials would accelerate EC adoption allowing them to be supplemented for regular windows without altering window construction. In this study, an ITO/WO3/Nb2O5/NiVOχ/ITO all-solid-state monolithic ECD with an effective area of 24 cm × 18 cm is successfully integrated on a PET substrate by using magnetron sputter deposition. The electrochromic performance and bending durability of the resultant material are also investigated. The experimental results indicate that the ultimate response times for the prepared ECD is 6 s for coloring at an applied voltage of -3 V and 5 s for bleaching at an applied voltage of +3 V, respectively. The optical transmittances for the bleached and colored state at a wavelength of 633 nm are 53% and 11%, respectively. The prepared ECD can sustain over 8000 repeated coloring and bleaching cycles, as well as tolerate a bending radius of curvature of 7.5 cm.

  15. Low-Temperature Preparation of Tungsten Oxide Anode Buffer Layer via Ultrasonic Spray Pyrolysis Method for Large-Area Organic Solar Cells.

    Science.gov (United States)

    Ji, Ran; Zheng, Ding; Zhou, Chang; Cheng, Jiang; Yu, Junsheng; Li, Lu

    2017-07-18

    Tungsten oxide (WO₃) is prepared by a low-temperature ultrasonic spray pyrolysis method in air atmosphere, and it is used as an anode buffer layer (ABL) for organic solar cells (OSCs). The properties of the WO₃ transition metal oxide material as well as the mechanism of ultrasonic spray pyrolysis processes are investigated. The results show that the ultrasonic spray pyrolysized WO₃ ABL exhibits low roughness, matched energy level, and high conductivity, which results in high charge transport efficiency and suppressive recombination in OSCs. As a result, compared to the OSCs based on vacuum thermal evaporated WO₃, a higher power conversion efficiency of 3.63% is reached with low-temperature ultrasonic spray pyrolysized WO₃ ABL. Furthermore, the mostly spray-coated OSCs with large area was fabricated, which has a power conversion efficiency of ~1%. This work significantly enhances our understanding of the preparation and application of low temperature-processed WO₃, and highlights the potential of large area, all spray coated OSCs for sustainable commercial fabrication.

  16. Low-Temperature Preparation of Tungsten Oxide Anode Buffer Layer via Ultrasonic Spray Pyrolysis Method for Large-Area Organic Solar Cells

    Directory of Open Access Journals (Sweden)

    Ran Ji

    2017-07-01

    Full Text Available Tungsten oxide (WO3 is prepared by a low-temperature ultrasonic spray pyrolysis method in air atmosphere, and it is used as an anode buffer layer (ABL for organic solar cells (OSCs. The properties of the WO3 transition metal oxide material as well as the mechanism of ultrasonic spray pyrolysis processes are investigated. The results show that the ultrasonic spray pyrolysized WO3 ABL exhibits low roughness, matched energy level, and high conductivity, which results in high charge transport efficiency and suppressive recombination in OSCs. As a result, compared to the OSCs based on vacuum thermal evaporated WO3, a higher power conversion efficiency of 3.63% is reached with low-temperature ultrasonic spray pyrolysized WO3 ABL. Furthermore, the mostly spray-coated OSCs with large area was fabricated, which has a power conversion efficiency of ~1%. This work significantly enhances our understanding of the preparation and application of low temperature-processed WO3, and highlights the potential of large area, all spray coated OSCs for sustainable commercial fabrication.

  17. A Novel Way to Prepare TiO2 and γ-Al2O3 Supported Catalysts with Large Surface Areas

    Institute of Scientific and Technical Information of China (English)

    ZHU Yue-Xiang ZHU Yue-Xiang; ZHAO Bi-Ying; ZHOU Chang-Jun; WANG Rong-Qiu; XIE You-Chang

    2001-01-01

    pared by a novel way and characterized by X-ray diffractiou,Raman spectroscopy and BET surface area measurement.The results show: (1) all the samples,including M0O3/TiO2,WO3/TiO2, V2Os/TiO2, FeSO4/γ-Al2O3, Al2(SO4)3/γ-Al2O3,K2CO3/-Al2O3 and so on,prepared by impregnating TiO2·H20or pseudo-boehmite AlO(OH)with the active components them calcining at a high temperature exhibit much larger surface ar-eas than that of pure TiO2 or γ-Al2O3 calcined at the same tem-perature; (2) the surface area of the sample increases with the increase in the coverage of active component on the surface of the support; (3) when the content of active component reaches its utmost monolayer dispersion capacity, the surface area of the sample is the largest, and then decreases when the content of active component exceeds its dispersion threshold.

  18. Preparation of born-doped a-SiC:H thin films by ICP-CVD method and to the application of large-area heterojunction solar cells.

    Science.gov (United States)

    Jeong, Chaehwan; Kim, Young-Back; Lee, Suk-Ho; Kim, Jin Hyeok

    2010-05-01

    Hydrogenated amorphous silicon carbide (a-SiC:H) film has been widely used as an emitter p layer in solar cells. For the better p layer, wide optical bandgap, and high electrical conductivity should be obtained from the effective method. We prepared the boron-doped a-SiC:H thin films using inductively coupled plasma chemical vapor deposition (ICP-CVD) method and characteristics on the small-area (2 cm x 2 cm) as well as the large-area films (diameter of 100 mm) were shown on it. As a substrate, the n-type (100) oriented CZ c-Si (5.5 approximately 6.5 omega x cm, 650 microm) wafers were used and cleaned by using the reduced RCA method. A silane (SiH4) of 99.999% purity, H2 and 60% hydrogen diluted ethylene (C2H4) was used as source gas for the deposition of intrinsic a-SiC:H films, and then diborane (B2H6), as the doping gas, is added to C2H4 and SiH4/H2 during the deposition of films. The uniformity of thickness and optical bandgap from large-area as-dep. films was at 1.8% and 0.3%, respectively. Heterojunction solar cell with 2 wt%-AZO/p-a-SiC:H/i-a-Si:H/c-Si/Ag structure was fabricated and characterized with diameter of 152.3 mm in this large-area ICP-CVD system. Conversion efficiency of 9.123% was achieved with a practical area of 100 mm x 100 mm, which can show the potentials to the fabrication of the large-area solar cell using ICP-CVD method.

  19. The large-area CdTe thin film for CdS/CdTe solar cell prepared by physical vapor deposition in medium pressure

    Science.gov (United States)

    Luo, Run; Liu, Bo; Yang, Xiaoyan; Bao, Zheng; Li, Bing; Zhang, Jingquan; Li, Wei; Wu, Lili; Feng, Lianghuan

    2016-01-01

    The Cadmium telluride (CdTe) thin film has been prepared by physical vapor deposition (PVD), the Ar + O2 pressure is about 0.9 kPa. This method is a newer technique to deposit CdTe thin film in large area, and the size of the film is 30 × 40 cm2. This method is much different from the close-spaced sublimation (CSS), as the relevance between the source temperature and the substrate temperature is weak, and the gas phase of CdTe is transferred to the substrate by Ar + O2 flow. Through this method, the compact and uniform CdTe film (30 × 40 cm2) has been achieved, and the performances of the CdTe thin film have been determined by transmission spectrum, SEM and XRD. The film is observed to be compact with a good crystallinity, the CdTe is polycrystalline with a cubic structure and a strongly preferred (1 1 1) orientation. Using the CdTe thin film (3 × 5 cm2) which is taken from the deposited large-area film, the 14.6% efficiency CdS/CdTe thin film solar cell has been prepared successfully. The structure of the cell is glass/FTO/CdS/CdTe/graphite slurry/Au, short circuit current density (Jsc) of the cell is 26.9 mA/cm2, open circuit voltage (Voc) is 823 mV, and filling factor (FF) is 66.05%. This technique can be a quite promising method to apply in the industrial production, as it has great prospects in the fabricating of large-area CdTe film.

  20. Preparing the way for coming area wide integrated pest management projects against the new world screwworm, Cochliomyia hominivorax, in MERCOSUR

    Energy Technology Data Exchange (ETDEWEB)

    Mastrangelo, Thiago; Fernandes, Thiago; Walder, Julio, E-mail: piaui@cena.usp.br [Centro de Energia Nuclear na Agricultura (CENA/USP), Piracicaba, SP (Brazil); Bezerra, Fernando [Instituto Federal de Educacao, Ciencia e Tecnologia do Sertao Pernambucano (IFSERTAO-PE), Petrolina, PE (Brazil)

    2011-07-01

    The New World Screwworm (NWS), Cochliomyia hominivorax, was eradicated from the USA, Central America to Panama, but in most tropical regions of Latin America, the NWS is still a serious threat to livestock, provoking estimated annual losses of US$ 1.8 billion in Brazil. Between January and May 2009, a pilot-project was performed at the Brazil-Uruguay border. As the results were positive, novel regional Area-Wide Integrated Pest Management projects are being planned. To set a mass-rearing center based in South America is strategic when considering long-term programs. In partnership with CENA/USP and the Biofactory MOSCAMED Brazil, a project to produce sterile NWS started on 2009. The project aimed to maintain a colony of a regional NWS strain, to develop a mass-rearing system and a sterilization protocol by X rays, and to study the sterility induction in regional strains. A colony was successfully established. The adults were kept in cages and fed on a diet (honey and spray dried egg). The larvae were reared in a medium made of spray dried blood, spray dried egg, milk, water, formalin and Ecogel. Egg hatch has been of 80 {+-} 10%. From F{sub 1} to F{sub 22}, the total amount of pupae produced was about 38 L ({approx} 315,400 pupae). The mean adult emergence and sex ratio were 86.7 {+-} 3% and 0.59 {+-} 0.08 respectively. The mean pupal weight was 47.1 {+-} 1.7 mg. The estimated X ray doses to induce 99% sterility in males and females were 43.7 Gy and 47.5 Gy, respectively. To produce 1.5 L of pupae, the current cost is about US$ 15.00. (author)

  1. Preparation of graphitic carbon nitride with large specific surface area and outstanding N2 photofixation ability via a dissolve-regrowth process

    Science.gov (United States)

    Ma, Huiqiang; Shi, Zhenyu; Li, Qiang; Li, Shuang

    2016-12-01

    Nitrogen fixation is the second most important chemical process in nature next to photosynthesis. Here, we report a convenient dissolve-regrowth method for synthesizing graphitic carbon nitride (g-C3N4) with a large surface area and nitrogen vacancies by HCl treatment. XRD, N2adsorption, SEM, TEM, UV-Vis spectroscopy, EPR, N2-TPD, Photoluminescence and Photocurrent were used to characterize the prepared catalysts. The results indicate that HCl treatment does not influence the crystal phase of g-C3N4 but change the morphology and optical property, leading to the smaller particle size, larger surface area and increased bang gap energy. It is deduced by N2-TPD, Photoluminescence, Photocurrent and DFT simulations that the nitrogen vacancies formed by the HCl treatment not only serve as active sites to adsorb and activate N2 molecules but also promote interfacial charge transfer from g-C3N4to N2 molecules. The HCl treated g-C3N4 catalyst exhibits outstanding nitrogen photofixation ability under visible light, which is 13.4-fold higher than that of bulk g-C3N4 without nitrogen vacancy. The possible reaction mechanism is proposed.

  2. Growth, structural and optical properties of ternary InGaN nanorods prepared by selective-area metalorganic chemical vapor deposition.

    Science.gov (United States)

    Song, Jie; Leung, Benjamin; Zhang, Yu; Han, Jung

    2014-06-06

    Ternary InGaN nanorods were prepared on dielectric-masked nano-holes with selective area metalorganic chemical vapor deposition. To overcome the tendency for random nucleation of GaN at low temperatures, a pulsed growth procedure was introduced to enhance the diffusion length of Ga adatoms on SiO2, resulting in good selectivity at typical temperature ranges for InGaN. Photoluminescence from the InGaN nanorods can be tuned from near ultraviolet (400 nm) to blue-green (~500 nm). Microstructural properties were characterized by transmission electron microscopy; threading dislocations from the underlying GaN template were terminated at the nanorod/template interface, resulting in dislocation-free nanorods. The height of dislocation-free InGaN nanorods is about 150 nm, which is much larger than the critical thickness for the onset of misfit dislocations in planar InGaN growth with typical thickness of less than 10 nm for an indium composition between 10 and 20%. The composition profile of In along the growth direction was examined by energy dispersive x-ray spectroscopic mapping and line scan. Oscillations of In composition along the growth direction were observed and are likely due to the kinetic competition between In and Ga adatoms. These InGaN nanorods are expected to be useful as templates for growing higher In composition nano-light-emitting diodes.

  3. Preparation of activate carbon with high specific surface area from beer lees by chemical activation with KOH; Suisankakariumu wo mochiita yakuhin fukatsuho ni yoru birukasu karano kohihyoumenseki kasseitan no seizo

    Energy Technology Data Exchange (ETDEWEB)

    Hayashi, J.; Kubo, A.; Furukawa, A.; Muroyama, K. [Kansai University, Osaka (Japan). Dept. of Chemical Engineering

    2000-03-10

    Activated carbons with high specific surface area were prepared from beer lees by chemical activation with KOH. We examined the influence of the preparation conditions, such as temperature and impregnation ratio, on the pore structure of the prepared activated carbon. The specific surface area increased with an increase in carbonization temperature up to 800 degree C and decreased at 900 degree C because of excess activation. It reached a maximum value at the impregnation ratio of 2.0. The activated carbon, which was prepared at the carbonization temperature of 800 degree C and at the impregnation ratio of 2.0, had very high specific surface area of 2,440 m{sup 2}/g. It was found that KOH worked effectively as the activating reagent in two temperature ranges, below 500 degree C and above 600 degree C. The amount of benzene and acetone adsorbed on the prepared activated carbon were much larger than that on the commercial activated carbons. (author)

  4. Surfactant-assisted sol gel preparation of high-surface area mesoporous TiO{sub 2} nanocrystalline Li-ion battery anodes

    Energy Technology Data Exchange (ETDEWEB)

    Casino, S. [GAME Lab, Department of Applied Science and Technology – DISAT, Institute of Chemistry, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Torino (Italy); Di Lupo, F., E-mail: francesca.dilupo@polito.it [GAME Lab, Department of Applied Science and Technology – DISAT, Institute of Chemistry, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Torino (Italy); Francia, C. [GAME Lab, Department of Applied Science and Technology – DISAT, Institute of Chemistry, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Torino (Italy); Tuel, A. [IRCELYON, Institut de Recherches sur la Catalyse et l’environnement de Lyon, UMR 5256, CNRS-Université de Lyon 1, 2 Avenue Albert Einstein, 69626 Villeurbanne Cedex (France); Bodoardo, S. [GAME Lab, Department of Applied Science and Technology – DISAT, Institute of Chemistry, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Torino (Italy); Gerbaldi, C., E-mail: claudio.gerbaldi@polito.it [GAME Lab, Department of Applied Science and Technology – DISAT, Institute of Chemistry, Politecnico di Torino, C.so Duca degli Abruzzi 24, 10129 Torino (Italy)

    2014-05-01

    Highlights: • Mesoporous TiO{sub 2} nanocrystalline lithium battery anodes with tunable morphology. • Simple sol–gel technique using different cationic surfactants is adopted. • Textural/morphological characteristics define the electrochemical behaviour. • TiO{sub 2} anatase using C16TAB exhibits stable performance after 200 cycles. • It shows promising prospects as high-voltage safe Li-ion battery anode. - Abstract: We here investigate the physico-chemical/morphological characteristics and cycling behaviour of several kinds of nanocrystalline TiO{sub 2} Li-ion battery anodes selectively prepared through a simple sol–gel strategy based on a low-cost titanium oxysulfate precursor, by mediation of different cationic surfactants having different features (e.g., chain lengths, counter ion, etc.): i.e., cetyl-trimethylammonium bromide (CTAB), cetyl-trimethylammonium chloride (CTAC), benzalkonium chloride (BC) or octadecyl-trimethyl ammonium bromide (C{sub 18}TAB). X-ray diffraction profiles reveal single phase anatase having good correspondence with the reference pattern when using short chain CTAB, while in the other cases the presence of chloride and/or an increased chain length affect the purity of the samples. FESEM analysis reveal nanosized particles forming cauliflower-like aggregates. TiO{sub 2} materials demonstrate mesoporous characteristics and large specific surface area ranging from 250 to 30 m{sup 2} g{sup −1}. Remarkably stable electrode performance are achieved by appropriately selecting the cationic surfactant and the surfactant/precursor ratio. Detailed analysis is provided on the effect of the reaction conditions upon the formation of mesoporous crystalline titania enlightening new directions for the development of high performing lithium storage electrodes by a simple and low cost sol–gel strategy.

  5. Health education through analogies: preparation of a community for clinical trials of a vaccine against hookworm in an endemic area of Brazil.

    Directory of Open Access Journals (Sweden)

    Maria Flavia Gazzinelli

    Full Text Available BACKGROUND: Obtaining informed consent for clinical trials is especially challenging when working in rural, resource-limited areas, where there are often high levels of illiteracy and lack of experience with clinical research. Such an area, a remote field site in the northeastern part of the state of Minas Gerais, Brazil, is currently being prepared for clinical trials of experimental hookworm vaccines. This study was conducted to assess whether special educational tools can be developed to increase the knowledge and comprehension of potential clinical trial participants and thereby enable them to make truly informed decisions to participate in such research. METHODOLOGY/PRINCIPAL FINDINGS: An informational video was produced to explain the work of the research team and the first planned hookworm vaccine trial, using a pedagogical method based on analogies. Seventy-two adults living in a rural community of Minas Gerais were administered a structured questionnaire that assessed their knowledge of hookworm, of research and of the planned hookworm vaccine trial, as well as their attitudes and perceptions about the researchers and participation in future vaccine trials. The questionnaire was administered before being shown the educational video and two months after and the results compared. After viewing the video, significant improvements in knowledge related to hookworm infection and its health impact were observed: using a composite score combining related questions for which correct answers were assigned a value of 1 and incorrect answers a value of 0, participants had a mean score of 0.76 post-video compared to 0.68 pre-video (p = 0.0001. Similar improvements were seen in understanding the purpose of vaccination and the possible adverse effects of an experimental vaccine. Although 100% of participants expressed a positive opinion of the researchers even before viewing the film and over 90% said that they would participate in a hookworm vaccine

  6. 具有高比表面积的稻壳灰的制备及其化学活性的研究%Study on Preparation of Rice Husk Ash with High Specific Surface Area and Its Chemical Reactivity

    Institute of Scientific and Technical Information of China (English)

    冯庆革; 林清宇; 童张法; S.Sugita

    2004-01-01

    Preparation of rice husk ash with high specific surface area and chemical reactivity of the product are reported in this paper. The amorphous rice husk ash with high specific surface area of 311 m2·g-1 was produced by heating acid treated rice husk at 700℃ for 4 h. The isotherms of rice husk ash are similar in shape to type Ⅱof Brunaner's classification with mesopores being predominant. The rice husk ash has a high chemical reactivity,especially that pretreated with acid. This chemical reactivity depends on ashing temperature and pretreatment conditions. There is an exponential relation between the specific surface area of rice husk ash and the change in the conductivity of saturated Ca(OH)2 solution with rice husk ash, from which the specific surface area can be known according to the conductivity change.

  7. Food preparation methods, drinking water source, and esophageal squamous cell carcinoma in the high-risk area of Golestan, Northeast Iran.

    Science.gov (United States)

    Golozar, Asieh; Etemadi, Arash; Kamangar, Farin; Fazeltabar Malekshah, Akbar; Islami, Farhad; Nasrollahzadeh, Dariush; Abedi-Ardekani, Behnoosh; Khoshnia, Masoud; Pourshams, Akram; Semnani, Shahriar; Marjani, Haji Amin; Shakeri, Ramin; Sotoudeh, Masoud; Brennan, Paul; Taylor, Philip; Boffetta, Paolo; Abnet, Christian; Dawsey, Sanford; Malekzadeh, Reza

    2016-03-01

    Cooking practices and water sources have been associated with an increased risk of cancer, mainly through exposure to carcinogens such as heterocyclic amines, polycyclic aromatic hydrocarbons, and nitrates. Using data from the Golestan case-control study, carried out between 2003 and 2007 in a high-risk region for esophageal squamous cell carcinoma (ESCC), we sought to investigate the association between food preparation and drinking water sources and ESCC. Information on food preparation methods, sources of drinking water, and dietary habits was gathered from 300 cases and 571 controls matched individually for age, sex, and neighborhood using a structured questionnaire and a semiquantitative food frequency questionnaire. Multivariate conditional logistic regression was used to estimate odds ratios (OR) and 95% confidence intervals (CI) adjusted for potential confounders and other known risk factors including socioeconomic status and smoking. More than 95% of the participants reported eating meat, mostly red meat. Red meat consumption above the 75th percentile increased the odds of ESCC by 2.82-fold (95% CI: 1.21-6.57). Fish intake was associated with a significant 68% decrease in ESCC odds (26%, 86%). Among meat eaters, ORs (95% CI) for frying meat (red or white) and fish were 3.34 (1.32-8.45) and 2.62 (1.24-5.5). Drinking unpiped water increased ESCC odds by 4.25 times (2.23-8.11). The OR for each 10-year increase in the duration of drinking unpiped water was 1.47 (1.22-1.78). Our results suggest roles for red meat intake, drinking water source, and food preparation methods in ESCC, even after adjusting for a large number of potential confounders.

  8. CROSS-DISCIPLINARY PHYSICS AND RELATED AREAS OF SCIENCE AND TECHNOLOGY: Preparation and Characterization of BPO Film as Electrode for Using of FeRAM

    Science.gov (United States)

    Wen, Xin-Yi; Yu, Jun; Wang, Yun-Bo; Zhou, Wen-Li; Gao, Jun-Xiong; Chu, Xiao-Hui

    2008-07-01

    Conductive perovskite BaPbO3 (BPO) films as a potential electrode material of PZT capacitors used in ferroelectric random access memory are prepared by rf magnetron sputtering. An x-ray diffractometer and standard four probe method are employed to investigate the dependence of growth conditions on crystal structure and conductivity of BPO films. It is found that BPO films with perovskite phase can be obtained at substrate temperatures above 425° C, and the sample with the lowest resistivity is obtained at 450° C under pure argon atmosphere. Using this BPO film as electrode, ferroelectric properties of BPO/PZT/BPO and Pt/PZT/BPO sandwiched structures are evaluated. Their remanent polarization and coercive field are 36.6μC/cm2 (81.3kV/cm) and 36.9μC/cm2 (89.1 kV/cm), respectively. The coercive field of the former structure is lower than that of the latter, but remanent polarizations are almost the same. In addition, the results imply that BPO electrode is helpful to improve the fatigue resistance of PZT. The reasons are discussed.

  9. Increase of the processing capacity through modification and enlargement of the assets areas preparation and waste water purification in the fermentation plant Kirchstockach; Durchsatzsteigerung der Vergaerungsanlage Kirchstockach durch Umbau und Erweiterung der Anlagenbereiche Aufbereitung und Prozesswasserreinigung

    Energy Technology Data Exchange (ETDEWEB)

    Kirschenhofer, M. [LRA Muenchen (Germany). Tiefbau, Verkehrsplanung, Abfallwirtschaft; Kroner, T. [ia GmbH - Wissensmanagement und Ingenieurleistungen, Muenchen (Germany). Bereich Kommunale Abfallwirtschaft und Energie; Niefnecker, U. [M. Ganser GmbH und Co. Entsorgungsbetriebe KG, Brunnthal/Kirchstockach (Germany)

    2006-04-15

    At the fermentation plant Kirchstockach the operations for the rectification of deficiencies and process optimisations were completed in 2004. Now process results of 2005 show the success of the performed actions. In the asset area of preparations the existing rake discharge system was removed and the use of the new discharge reservoir with a drainage coil conveyor system minimises deadlock times and rises preparations throughput. With the new set-up of the light material presses the process procedure was optimised, too. The installation of the new process water reservoir was conditional on the non-uniform hydraulic load of the waste-water purification, which results from the operation of the facility. With the higher buffer capacity, realised by the new process water reservoir, a uniform hydraulic load of the purification system and an optimised process control was implemented. With the optimised performance of the wastewater purification wastewater thresholds are guaranteed now and it is possible to realise the increased throughput of the preparation in the complete system of the fermentation plant Kirchstockach. (orig.)

  10. 泡沫镍的制备工艺条件和比表面积%Preparation Technological Conditions and Specific Surface Area of Nickel Foams

    Institute of Scientific and Technical Information of China (English)

    段翠云; 崔光; 刘培生

    2011-01-01

    Based on the technique of electrodeposition on the organic foam, relationship between several deferent specific producing conditions and the corresponding specific surface area of nickel foam products has been investigated.The result showed that the same surface morphology and specific surface area of the nickel foam could be acquired by direct sintering in NH3 decomposition atmosphere at 850 ℃ or 980 ℃ for 40 min after electrodepositing and by burning in air at 600 ℃ for 4 min before and then reductive sintering, after electrodepositing.%本文以有机泡沫电沉积法为基础,探讨了几种具体工艺条件与所得泡沫镍产品比表面积的关系.结果发现,电镀后直接在850~980℃的氨分解气氛中烧结40 min所得产品,与电镀后先在600℃的空气中烧结4 min再进行还原烧结所得产品,具有相同的表面形态和比表面积.

  11. Assessment of Diversity, Distribution, Conservation Status and Preparation of Management Plan for Medicinal Plants in the Catchment Area of Parbati Hydroelectric Project Stage -Ⅲ in Northwestern Himalaya

    Institute of Scientific and Technical Information of China (English)

    S.S. Samant; Jitendra S. Butola; Aman Sharma

    2007-01-01

    The developmental activities, particularly the construction of hydroelectric projects are causing a great loss of biodiversity in the Indian Himalayan Region. The Himachal Pradesh, a part of IHR is well known for the development of hydroelectric projects.The Parbati H.E. Project is amongst the major projects of the State. The different stages of the project are all causing loss of biodiversity of the area.Stage Ⅲ of the Parbati H.E. Project is a run of the river scheme on the Sainj River downstream of Power House of Parbati H.E. Project Stage Ⅱ. The project shall utilize regulated discharge of Parbati H.E.Project Stage Ⅱ and inflow of River Sainj for power generation, and has been contemplated as a peaking station operating in tandem with Stage Ⅱ. The present study has been undertaken to see the impact of hydroelectric project on the biodiversity, particularly on medicinal plants. A total of 104 species of medicinal plants, belonging to different life forms, i.e.,trees (23 spp.), shrubs (22 spp.), herbs (57 spp.) and ferns (2 spp.) were recorded. The species have been analyzed and studied for their distribution,classification, altitudinal zones, part (s) used,indigenous uses, nativity, endemism and rarity.Different parts of these species, such as whole plants,roots (including rhizomes and tubers), leaves, flowers,fruits, seeds, stems, barks, spikes, nuts and insect galls are used by the inhabitants for curing various diseases and ailments. 30 species are native to the Himalayan region, 9 species native to the Himalayan region and adjacent countries also and 65 species are non-natives. 9 species are near endemics. Considering the whole Himalaya as a biogeographic unit (sensu lato),the near endemics are endemic to the Himalaya.Among these species, Zanthoxylum armatum is categorized as Endangered and Valeriana wallichii as Vulnerable. Hedychium spicatum, Rhus javanica,Berberis lycium, Thalictrum foliolossum, Salvia lanata, Rubia cordifolia and Bergenia

  12. A new preparation of doped photocatalytic TiO2 anatase nanoparticles: a preliminary study for the removal of pollutants in confined museum areas

    Science.gov (United States)

    Greco, Enrico; Ciliberto, Enrico; Cirino, Antonio M. E.; Capitani, Donatella; Di Tullio, Valeria

    2016-05-01

    The use of nanotechnology in conservation is a relatively new concept. Usually, classical cleanup methods take into account the use of other chemicals: On the one hand they help the environment destroying pollutants, but on the other hand they often become new pollutants. Among the new oxidation methods called advanced oxidation processes, heterogeneous photocatalysis has appeared an emerging technology with several economic and environmental advantages. A new sol-gel method of synthesis of TiO2 anatase is reported in this work using lithium and cobalt (II) salts. The activation energy of the doped photocatalyst was analyzed by solid-state UV-Vis spectrophotometer. The mobility of Li ions on TiO2 NPs surface was studied by 7Li MAS NMR spectroscopy. Use of doped nanotitania is suggested from authors for the removal of pollutants in confined areas containing goods that must be preserved from decomposition and aging phenomena.

  13. How prepared individuals and communities are for evacuation in tsunami-prone areas in Europe? Findings from the ASTARTE EU Programme

    Science.gov (United States)

    Lavigne, Franck; Grancher, Delphine; Goeldner-Gianella, Lydie; Karanci, Nuray; Dogulu, Nilay; Kanoglu, Utku; Zaniboni, Filippo; Tinti, Stefano; Papageorgiou, Antonia; Papadopoulos, Gerassimos; Constantin, Angela; Moldovan, Iren; El Mouraouah, Azelarab; Benchekroun, Sabah; Birouk, Abdelouahad

    2016-04-01

    Understanding social vulnerability to tsunamis provides risk managers with the required information to determine whether individuals have the capacity to evacuate, and therefore to take mitigation measures to protect their communities. In the frame of the EU programme ASTARTE (Assessment, STrategy And Risk reduction for Tsunamis in Europe), we conducted a questionnaire-based survey among 1,661 people from 41 nationalities living in, working in, or visiting 10 Test Sites from 9 different countries. The questions, which have been translated in 11 languages, focused on tsunami hazard awareness, risk perception, and knowledge of the existing warning systems. Our results confirm our initial hypothesis that low attention is paid in Europe to tsunami risk. Among all type of hazards, either natural or not, tsunami rank first in only one site (Lyngen fjord in Norway), rank third in 3 other sites (Eforie Nord in Romania, Nice and Istanbul), rank 4 in Gulluk Bay, 5 in Sines and Heraklion, and 10 in Siracusa (Sicily) and San Jordi (Balearic Islands). Whatever the respondent's status (i.e. local population, local authorities, or tourists), earthquakes and drawdown of the sea are cited as tsunami warning signs by 43% and 39% of the respondents, respectively. Therefore self-evacuation is not expected for more than half of the population. Considering that most European countries have no early warning system for tsunamis, a disaster is likely to happen in any coastal area exposed to this specific hazard. Furthermore, knowledge of past tsunami events is also very limited: only 22% of people stated that a tsunami has occurred in the past, whereas a deadly tsunami occurs every century in the Mediterranean Sea (e.g. in AD 365, 1660, 1672 or 1956 in the eastern part, 1908, 1979 or 2003 in the western part), and high tsunami waves devastated the Portugal and Moroccan coasts in 1755. Despite this lack of knowledge and awareness of past events, 62% of the respondents think that the site of

  14. The preparation of the poly(vinyl alcohol/graphene nanocomposites with low percolation threshold and high electrical conductivity by using the large-area reduced graphene oxide sheets

    Directory of Open Access Journals (Sweden)

    Q. Fu

    2013-09-01

    Full Text Available We report a method to prepare the poly(vinyl alcohol/reduced graphene oxide (PVA/rGO nanocomposites with low percolation threshold and high electrical conductivity by using the large-area reduced graphene oxide (LrGO sheets. The large-area graphene oxide (LGO sheets are expected to overlap better with each other and form the continuous GO network in PVA matrix than small-area graphene oxide (SGO. During the thermal reduction process, the LGO sheets are easily restored and improve the electrical conductivity of nanocomposites due to their low damage level of conjugate-structure. As a result, the percolation threshold of PVA/LrGO nanocomposites is ~0.189 wt% lower than present reports (0.5~0.7 wt%. At the LrGO content of 0.7 wt%, the electrical conductivity of PVA/LrGO nanocomposites reaches 6.3•10–3 S/m. Besides that, this method only takes 15~30 min to reduce the PVA/GO nanocomposites effectively.

  15. Preparation and Application of Corn Stalk Silage in High Altitude Areas%高海拔地区玉米秸秆的青贮制作及应用

    Institute of Scientific and Technical Information of China (English)

    王德辉; 付照武

    2015-01-01

    介绍了高海拔地区玉米秸秆的青贮方法(包括青贮窖制作、秸秆准备、秸秆入窖及平整压紧、封窖过程4个步骤),出窖时间,秸秆品质的检验(如质地、气味、颜色和pH值等),青贮饲料的饲喂技术,以期为当地玉米等饲草料资源的充分利用和家畜养殖提供参考。%In this paper, the preparation methods of corn stalk silage in high altitude areas, including constraction of silage cellar, preparation of corn stalk, placement of corn stalk into silage cellar, planishing corn stalk silage mound, sealing of silage cellar , terminal time of silage fermentation, test of corn stalk quality (character, odor, color, pH value, etc.) were introduced,and the silage feeding technology were also reviewed, so as to provide references for the full utilization of local corn and other forage resources and domestic animal breeding.

  16. Annotated bibliography on selected areas of coal mining research and development. Report prepared for the Committee on Science and Technology, US House of Representatives, Ninety-Sixth Congress, First Session by the Congressional Research Service, Library of Congress

    Energy Technology Data Exchange (ETDEWEB)

    1979-01-01

    The Congressional Research Service has completed an annotated bibliography on coal mining research and development. Although the completion of the study was delayed in order to permit CRS analysts to search the libraries of Bituminous Coal, Research Inc., and the Bureau of Mines in the Pittsburgh area, current re-emphasis on the use of coal as an energy source indicates a sustained relevance. The bibliography presents key references to coal-mining R and D under six subject headings keyed to issues of central concern in coal production: (1) mine health and safety, (2) methane recovery, (3) 1-hour rescuer, (4) use of diesels underground, (5) coal preparation, and (6) manpower development in coal mining.

  17. 制造业半成品备料区布局与物流优化研究%Manufacturing Semi-finished Product Preparation Area Layout and Logistics Optimization Research

    Institute of Scientific and Technical Information of China (English)

    董鹏; 张易涛

    2013-01-01

      要:以卡莱公司为例,针对该企业半成品备料区的布局状况,指出生产物流存在的问题,提出具体优化布局策略。利用工业工程改善工具对备料区域的布局与物流路线进行优化,通过对比改善前后的物料搬运距离、费用、耗用工时等相关指标发现,此次改善有效地解决了半成品备料布置问题,提高了生产效率,优化了生产流程,节约了成本。%In order to Carlisle company as an example, for the semi-finished material staging area situation, point out production logistics problems, put forward specific optimization layout strategy. Use of industrial engineering to improve the tools on the preparation area distribution and logistics route optimization, by comparing the improved material handling distance, cost, consumption of time related indexes were found, the improvement can effectively solve the semi-finished stock layout problem, improves the production efficiency, optimize the production process, saving the cost.

  18. Research Progress in Preparation of Sandy Alumina with High Specific Surface Area%高比表面积砂状氧化铝制备研究进展∗

    Institute of Scientific and Technical Information of China (English)

    曹磊; 尹建国; 廖亚龙; 黄斐荣; 王祎洋

    2016-01-01

    Specific surface area,an important parameter of sand-shape Al2 O3 ,has remarkable effects on the characteristics of the product,such as dissolution performance and fluoride absorption ability.The microcosmic mechanism of pore structure′s effect on specific surface area was introduced,and influences of several controlling measures on properties like morphology,size distribution and especially specific surface area during the seeded precipi-tation process of sodium aluminate solution and the calcination process of aluminium hydroxide were discussed.A quick overview of some recent preparation technologies by enhancement with external field and modification of the so-lution system,and the performance of the product were given as well.It′s proposed that the new methods can match the present technology effectively,which means a feasible process for preparing different kinds of products with high specific surface area from metallurgical-grade sandy Al2 O3 to chemistry active Al2 O3 .The way to break through the bottleneck that the intensity of product will decrease with the increase of specific surface area and to obtain sandy Al2 O3 with high quality are still research focuses in the future.%比表面积是砂状 Al2 O3的重要参数,对产品的溶解性能、吸氟能力等特性有显著影响。介绍了影响Al2 O3比表面积的微观孔结构因素,分析了铝酸钠溶液分解过程和氢氧化铝煅烧过程的调控措施对砂状 Al2 O3产品形貌、粒度、比表面积等参数的影响,概述了外场强化、改变溶液体系等新的制备技术及其产品性能。指出各种强化技术可与现行生产工艺相匹配,为产出冶金级砂状 Al2 O3和化学品活性 Al2 O3等不同种类的高比表面积产品提供了新的途径。认为突破强度随比表面积增大而降低这一瓶颈并开发出高质量的砂状Al2 O3依然是今后的一个研究热点。

  19. Preparation of high specific surface area carbon aerogels by conventional drying and their performance in microstructure%超高比表面积碳气凝胶常压干燥制备与结构分析

    Institute of Scientific and Technical Information of China (English)

    刘西川; 袁磊; 王朝阳; 付志兵; 冯灏; 唐永建

    2012-01-01

    Carbon aerogels(CAs) and activated CAs doped with surfactant P123(PEO-PPO-PEO, molecular weight: 5 800) were prepared by conventional drying. SEM images show a handsome network structure of CAs prepared by conventional drying, and the network structure becomes more compact after activation. FTIR spectra show that there is strong interaction between PI 23 and RF (resorcinol-formaldehyde), and P123 disappears after carbonization. TG and DTG curve analyses indicate that the P123 is not a kind of impurity for it decomposes completely after carbonization at 440 ℃. Characterized by nitrogen adsorption, CAs prepared by conventional drying have a high specific surface area of 570 m2 ? g~' , which is up to about 3 500 m2 · g-1 after activation.%以间苯二酚(R)-甲醛(F)为原料,加入表面活性剂P123以增强材料的骨架强度的方法,采用常压干燥技术制备了RF碳气凝胶,并进行了二氧化碳活化以调节其孔结构.扫描电子显微镜(SEM)测试表明,常压干燥的碳气凝胶结构中具有更大的纳米颗粒,骨架结构变粗,活化使碳气凝胶骨架结构更加致密;红外吸收光谱(FTIR)表明,表面活性剂P123中的醚键与RF苯环中的羟基存在强的相互作用,碳化后P123特征峰消失;热重曲线(TG和DTG)分析说明P123在440℃左右分解完全,不会对碳气凝胶的成分产生影响,并能起到良好的造孔作用;氮气吸附表明常压干燥制备的碳气凝胶比表面积约为570m2/g,活化之后的比表面积高达3 500m2/g左右.

  20. Solution preparation

    Energy Technology Data Exchange (ETDEWEB)

    Seitz, M.G.

    1982-01-01

    Reviewed in this statement are methods of preparing solutions to be used in laboratory experiments to examine technical issues related to the safe disposal of nuclear waste from power generation. Each approach currently used to prepare solutions has advantages and any one approach may be preferred over the others in particular situations, depending upon the goals of the experimental program. These advantages are highlighted herein for three approaches to solution preparation that are currently used most in studies of nuclear waste disposal. Discussion of the disadvantages of each approach is presented to help a user select a preparation method for his particular studies. Also presented in this statement are general observations regarding solution preparation. These observations are used as examples of the types of concerns that need to be addressed regarding solution preparation. As shown by these examples, prior to experimentation or chemical analyses, laboratory techniques based on scientific knowledge of solutions can be applied to solutions, often resulting in great improvement in the usefulness of results.

  1. Difluoromethane preparation

    NARCIS (Netherlands)

    Wiersma, A.; Sandt, E.J.A.; Van Bekkum, H.; Makkee, M.; Moulijn, J.A.

    1996-01-01

    Abstract of NL 9401574 (A) The invention relates to a method for preparing difluoromethane, wherein dichlorodifluoromethane or monochlorodifluoromethane is brought into contact with hydrogen in the presence of palladium on activated carbon, wherein the loading of the palladium on the activated c

  2. Preparation and Characterization of High Surface Area α-AlF3%高比表面积α-AlF3的制备和表征

    Institute of Scientific and Technical Information of China (English)

    于洪波; 王月娟; 彭小波; 朱琳; 罗孟飞

    2012-01-01

    采用炭硬模板法制备了高比表面积的α-AlF3(HS-α-AlF3).首先,将一定浓度的蔗糖溶液浸渍到γ-Al2O3中,然后经过热处理,使得蔗糖分解为炭.其次,将含炭的γ-Al2O3固体用HF气体进行氟化.最后,再利用燃烧法除去炭硬模板.采用XRD、低温氮吸附-脱附、NH3-TPD、SEM-EDX等技术对样品进行了表征.结果表明,当炭化温度为450 ℃时,HF-N2混合气体积比为1∶4,除碳温度为425℃时,制得的α-AlF3比表面积最大,为66 m2·g-1.此外,HS-α-AlF3催化剂对CCl2F2歧化反应的催化活性也明显高于常规方法制备的低比表面积的α-AlF3,这是因为高比表面积的α-AlF3催化剂具有较大的酸量.%High surface area α-AlF3 (HS-α-AlF3) has been prepared by a carbon hard template method. The synthesis procedure consisted of three steps: (1) the impregnation of a sucrose (C12H22O11) aqueous solution with 7-AI2O3 and subsequent thermal treatment; (2) the thermal treatment of the obtained solid with HF; (3) the removal of the carbon template in C()α-A1F3 upon high temperature combustion. The optimal conditions for the highest surface area of the synthesized α-AlF3 (66 m2 ·g-1) are obtained based on the results from XRD, low temperature adsorption-desorption, ammonia temperature programmed desorption (NH3-TPD), SEM, EDX and the FTIR spectra of pyridine adsorption. The temperatures for fluorination, carbon calcinations and carbon removal are 400, 450 and 425 ℃, respectively, and the HF/N2 volume ratio is 1:4. In addition, the HS-α-AlF3 catalyst is more active for the dismutation of CCI2F2 than the catalyst prepared by a direct fluorination of the γ-AI2O3 due to its higher amount of acid sites.

  3. How Prepared is Prepared Enough?

    Science.gov (United States)

    Porter-Levy; Macleod; Rickert

    1996-10-01

    A 17-year-old female was in the final stage in treatment of right unilateral cleft lip and palate. She had undergone a number of previous surgeries. Hearing and speech were good on evaluation, and her social and family situation were deemed excellent. After preparatory orthodontics she underwent a Lefort I maxillary advancement. Surgery was successful and she was admitted into postoperative recovery. However, the lack of adequate preoperative preparation caused traumatic reaction from the patient and her parents: anxiety over appearance, crying, refusal of oral fluids and oral care, refusal of analgesia, and refusal to mobilize. The patience and persistence of hospital staff slowly overcame all adversities and the patient moved on to full and successful recovery, but this case prompted changes in preoperative procedures and involvement of patients and their families in postoperative meal selection, planing, and preparation.

  4. Control Areas

    Data.gov (United States)

    Department of Homeland Security — This feature class represents electric power Control Areas. Control Areas, also known as Balancing Authority Areas, are controlled by Balancing Authorities, who are...

  5. Area Handbook for Syria.

    Science.gov (United States)

    Nyrop, Richard; And Others

    This volume on Syria is one of a series of handbooks prepared by the Foreign Area Studies (FAS) of the American University, designed to be useful to military and other personnel who need a convenient compilation of basic facts about the social, economic, political, and military institutions and practices of various countries. The emphasis is on…

  6. Area Handbook for Mozambique.

    Science.gov (United States)

    Herrick, Allison Butler

    This publication is one of a series of handbooks prepared by the Foreign Areas Studies (FAS) of The American University, designed to be useful to military and other personnel who need a convenient compilation of basic facts about the social, economic, political and military institutions and practices of various countries. The present handbook…

  7. Preparation for Family Life. The CCC's Project No. 1: "Preparation for Life."

    Science.gov (United States)

    Schleicher, Klaus

    Part of the Council of Europe's Project Number 1, "Preparation for Life," this report analyzes developments in Austria, Finland, the Federal Republic of Germany, and England in the area of preparation for family life. Specifically, the report (1) explains the growing concern in the above countries for the preparation for family life; (2)…

  8. Anchorage Areas

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — An anchorage area is a place where boats and ships can safely drop anchor. These areas are created in navigable waterways when ships and vessels require them for...

  9. Preparing for Surgery

    Science.gov (United States)

    ... Events Advocacy For Patients About ACOG Preparing for Surgery Home For Patients Search FAQs Preparing for Surgery ... Surgery FAQ080, August 2011 PDF Format Preparing for Surgery Gynecologic Problems What is the difference between outpatient ...

  10. Preparing for Surgery

    Science.gov (United States)

    ... Events Advocacy For Patients About ACOG Preparing for Surgery Home For Patients Search FAQs Preparing for Surgery ... Surgery FAQ080, August 2011 PDF Format Preparing for Surgery Gynecologic Problems What is the difference between outpatient ...

  11. Preparation of Leaders to Make Decisions in Peacekeeping Operations

    National Research Council Canada - National Science Library

    Pappal, Michael

    2002-01-01

    .... Areas investigated include personal confidence in decision-making of various types, amount of training and education received in peace operations, and assessments of Army preparations of leaders...

  12. Wooded areas

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This report summarizes the management of wooded areas on Neal Smith National Wildlife Refuge (formerly Walnut Creek National Wildlife Refuge) between 1992 and 2009.

  13. Revitalization Areas

    Data.gov (United States)

    Department of Housing and Urban Development — Revitalization areas are HUD-designated neighborhoods in need of economic and community development and where there is already a strong commitment by the local...

  14. 700 Area

    Data.gov (United States)

    Federal Laboratory Consortium — The 700 Area of the Hanford Site is located in downtown Richland.Called the Federal Office Building, the Richland Operations Site Manager and the Richland Operations...

  15. Pomegranate liquor preparation and analysis

    OpenAIRE

    Galego, Ludovina; Estevinho, Leticia M.; Silva, José Paulo

    2012-01-01

    The pomegranate (Punica granatum L.) liquor has been produced for several centuries in the south of Portugal, mainly in the mountain areas. The “Assaria” variety is the preferred cultivar due to its organoleptic properties and high arils to peel ratio. Wild pomegranates are also widely distributed but, despite the health benefits that have been associated to the fruits, they continue to be unappreciated for consumption. Liquor preparation is a very good alternative for wild pomegranate fruits...

  16. Marriage Preparation: Factors Associated with Consumer Satisfaction.

    Science.gov (United States)

    Russell, Mary N.; Lyster, Rosanne Farnden

    1992-01-01

    Evaluated marriage preparation program to determine overall consumer satisfaction with the program, satisfaction with specific content areas, and extent to which consumer characteristics affected satisfaction ratings. Results of survey of 196 couples revealed high overall satisfaction levels, variability in satisfaction by content area, and…

  17. Preparing for Multiple Births

    Science.gov (United States)

    ... Video Games, and the Internet Preparing for Multiple Births KidsHealth > For Parents > Preparing for Multiple Births Print ... a combination of both. The Risks of Multiple Births The most common risk involved with multiple births ...

  18. Preparation and Photocatalytic Characterization of Nanoporous TiO2

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Nanoporous TiO2 photocatalysts were prepared by use of controlled drying method with surfactants. The surface area and porous properties are dependent on the chain length of incorporated surfactant cation. The TiO2 materials prepared in the presence of surfactant molecules during the gel formation exhibit much higher photocatalytic activity than that prepared in the absence of surfactants.

  19. 9 CFR 108.5 - Preparation of legends.

    Science.gov (United States)

    2010-01-01

    ... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Preparation of legends. 108.5 Section... LICENSED ESTABLISHMENTS § 108.5 Preparation of legends. A brief description of the activities performed in each room or area shall be prepared as provided in this section and shall be referred to as a...

  20. Effective Area

    Directory of Open Access Journals (Sweden)

    Ehud Keinan

    2015-07-01

    Full Text Available This article defines a new term, Effective Area, K, of a given territory as a function of four independent parameters: its nominal acreage, A, the intellectual competence of its inhabitants, B, their social competence, C, and their global influence, D, using a simple formalism: K = A x B x C x D. This analysis demonstrates that in our current world any consideration of the physical area of a given territory is meaningless if the quality of its population is ignored. K is a much more useful parameter than A, certainly for political and economical considerations, explaining why claims for territorial expansion are placed low on the national ladder of priorities in the developed countries. In many respects, large geographical areas may become a burden rather than an advantage. Thus, the importance of armed conflicts over geographical territories, which have taken a dominant part of the entire human history, is fading away. Furthermore, although the global acreage is constant, the total effective area of planet Earth keeps growing, providing sufficient room for the growing human population.

  1. Thesis Preparation Manual

    OpenAIRE

    1999-01-01

    "This Thesis Preparation Manual has been written to provide you with format and procedure guidance for preparing and processing your thesis at the Naval Postgraduate School. It covers both unclassified and classified theses. All theses and thesis technical reports must be prepared in accordance with these guidelines. Please note that this manual is not written in the thesis format." form the Foreword

  2. Quiet areas

    DEFF Research Database (Denmark)

    Petersen, Rikke Munck

    2016-01-01

    This paper argues that drone filming can substantiate our understanding of multisensorial experiences of quiet areas and urban landscapes. Contrary to the distanced gaze often associated with the drone, this paper discusses drone filming as an intimate performativity apparatus that can affect per...... and transcendence can facilitate a deeper understanding of intimate sensations, substantiating their role in the future design and planning of urban landscapes. Hence, it addresses the ethics of an intimacy perspective (of drone filming) in the qualification of quiet areas.......This paper argues that drone filming can substantiate our understanding of multisensorial experiences of quiet areas and urban landscapes. Contrary to the distanced gaze often associated with the drone, this paper discusses drone filming as an intimate performativity apparatus that can affect...... perception as a result of its interrelationships between motion, gaze, and sound. This paper uses four films, one of which is a drone flyover, to launch a discussion concerning a smooth and alluring gaze, a sliding gaze that penetrates landscapes, and site appearance. Films hold the capacity to project both...

  3. International perspectives on coal preparation

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    The report consists of the vugraphs from the presentations which covered the following topics: Summaries of the US Department of Energy`s coal preparation research programs; Preparation trends in Russia; South African coal preparation developments; Trends in hard coal preparation in Germany; Application of coal preparation technology to oil sands extraction; Developments in coal preparation in China; and Coal preparation in Australia.

  4. Prepared for internship?

    LENUS (Irish Health Repository)

    Abuhusain, H

    2009-03-01

    Preparedness of medical school graduates for the intern year is one of the emphasised objectives of undergraduate medical training. We have evaluated the perceived preparedness of graduates undertaking the intern year in the Republic of Ireland. A 9-page questionnaire was mailed to all 497 interns in Ireland following commencement of the intern year in July 2005. Data obtained included demographics, perceived preparedness and assessment of perceived clinical skills (four sub-domains: core competencies, communication, emergencies, and educational environment). Information on intern induction was also collected. 99 questionnaires were returned (19.9%). Most of the cohort were Irish and worked in large medical school teaching hospitals. The majority of interns felt \\'unprepared\\' for the intern year. Interns perceived themselves \\'poor\\' in all areas of clinical skills assessed. Intern induction was attended by the majority and most stated it was too short. Medical schools are actively seeking innovative methods, through early patient contact and sub-internships, to better prepare undergraduates for the intern year. The deficiencies identified in this study are significant and emphasise the need for continued reform in the undergraduate curriculum.

  5. AREAS OF KUMASI, GHANA: THEORY VERSUS PRACTICE

    African Journals Online (AJOL)

    This resultsyin the high cost that individual de-. INTRODUCTION . There is .... govermnent system of Ghana. It covers an area .... Based on that the TCPD prepared a draft scheme for Ayeduase. .... guidelines for that activity. However, there is.

  6. [Aesthetic surgery, psychic preparation].

    Science.gov (United States)

    Feiss, R

    2003-10-01

    The aesthetic surgery impacts the psychological picture of the body. The candidate must be prepared to this change in appearance. If not, the surgeon must suggest the psychological preparation, evaluating the risk of dissatisfaction, in order to allow the surgical and narcissistic success of his operation. The author, a psychiatric, beneficiary in a strong experience of a surgical assistance, develops the interest of such a preparation upon a period of about 15 years (1988-2002).

  7. Materials Preparation Center

    Data.gov (United States)

    Federal Laboratory Consortium — MPC is recognized throughout the worldwide research community for its unique capabilities in purification, preparation, and characterization of: rare earth metals,...

  8. Materials Preparation Center

    Data.gov (United States)

    Federal Laboratory Consortium — MPC is recognized throughout the worldwide research community for its unique capabilities in purification, preparation, and characterization of: rare earth metals,...

  9. Rationale for designing cavity preparations.

    Science.gov (United States)

    Laswell, H R; Welk, D A

    1985-04-01

    Increased resistance to caries, increased dental awareness, superior diagnostic capabilities, better illumination, optical aids that significantly enhance vision, improved and standardized materials for restoration, and a deeper understanding of the caries process enable a far more conservative approach to tooth preparation. The dentist can concentrate on preserving as much sound tooth structure as possible with less attention being devoted to resistance and retention form that previously demanded in bulk restorations and massive channels and locks that are no longer appropriate. Although caries inhibitory effects have been shown with materials such as silicate cement, glass ionomers, and resins that leach fluoride, in general, dentists should not rely on restorative materials to inhibit the development of future decay. Characteristics of the carious lesion are unique for each tooth according to many factors centering around the plaque pattern for that tooth and not according to zones of natural susceptibility or immunity strictly dictated by morphology. Therefore, no single cavity preparation duplicated from a textbook is likely to be satisfactory for an individual tooth. Furthermore, novices learning the subject of cavity preparation often leave decalcified enamel when they attempt to replicate under clinical conditions that which they have learned in technique courses. This is the major invitation to future caries reappearing adjacent to restorations. Also, failure to duplicate the exact morphology of the tooth surface that has been replaced is likely to alter the pattern of plaque accumulation and create other caries prone areas.(ABSTRACT TRUNCATED AT 250 WORDS)

  10. Progress involving new techniques for liposome preparation

    Directory of Open Access Journals (Sweden)

    Zhenjun Huang

    2014-08-01

    Full Text Available The article presents a review of new techniques being used for the preparation of liposomes. A total of 28 publications were examined. In addition to the theories, characteristics and problems associated with traditional methods, the advantages and drawbacks of the latest techniques were reviewed. In the light of developments in many relevant areas, a variety of new techniques are being used for liposome preparation and each of these new technique has particular advantages over conventional preparation methods. However, there are still some problems associated with these new techniques that could hinder their applications and further improvements are needed. Generally speaking, due to the introduction of these latest techniques, liposome preparation is now an improved procedure. These applications promote not only advances in liposome research but also the methods for their production on an industrial scale.

  11. Texas Educational Reform: The Teacher Preparation Aspect.

    Science.gov (United States)

    Lindahl, Ronald A.; Descamps, Jorge

    1988-01-01

    Recent Texas legislation eliminates undergraduate degrees in education and requires academic majors for certification. Intended and unplanned consequences of the legislation are examined. Discussed are implications for teacher shortages, accreditation of teacher preparation institutions, specific areas (e.g., physical education, elementary…

  12. Thyroid preparation overdose

    Science.gov (United States)

    Thyroid preparations are medicines used to treat thyroid gland disorders. Overdose occurs when someone takes more than the normal or recommended amount of this medicine. This can be by accident or ...

  13. PLANNING DECISIONS IN LANDSLIDE AREAS

    Directory of Open Access Journals (Sweden)

    Maria Katarzyna Hełdak

    2016-09-01

    Full Text Available The study discusses the topic of planning decisions taken for the purposes of studies prepared on the municipality level and related to the development of landslide areas in Poland. The aim of the research is to demonstrate the scale of the issue consisting in designating areas at risk of subsidence of soil masses for investment purposes. The research emphasises the essential role of planning documentation in the prevention of investment in such areas. Other vital factors also include the SOPO (Landslide Counteracting System database as well as the staroste, who, in the course of preparation of planning documentation and issuing decisions on development conditions, issues opinions or agrees (depending on the type of document or decision on the planned investment in areas at risk of landslides. The study shows the complexity of the spatial planning and development system in Poland and the significant influence of bodies and institutions on the planned development of areas prone to the subsidence of soil masses.

  14. Action preparation shapes processing in early visual cortex.

    Science.gov (United States)

    Gutteling, Tjerk P; Petridou, Natalia; Dumoulin, Serge O; Harvey, Ben M; Aarnoutse, Erik J; Kenemans, J Leon; Neggers, Sebastian F W

    2015-04-22

    Preparation for an action, such as grasping an object, is accompanied by an enhanced perception of the object's action-relevant features, such as orientation and size. Cortical feedback from motor planning areas to early visual areas may drive this enhanced perception. To examine whether action preparation modulates activity in early human visual cortex, subjects grasped or pointed to oriented objects while high-resolution fMRI data were acquired. Using multivoxel pattern analysis techniques, we could decode with >70% accuracy whether a grasping or pointing action was prepared from signals in visual cortex as early as V1. These signals in early visual cortex were observed even when actions were only prepared but not executed. Anterior parietal cortex, on the other hand, showed clearest modulation for actual movements. This demonstrates that preparation of actions, even without execution, modulates relevant neuronal populations in early visual areas.

  15. Tech Area II: A history

    Energy Technology Data Exchange (ETDEWEB)

    Ullrich, R. [Ktech Corp., Albuquerque, NM (United States)

    1998-07-01

    This report documents the history of the major buildings in Sandia National Laboratories` Technical Area II. It was prepared in support of the Department of Energy`s compliance with Section 106 of the National Historic Preservation Act. Technical Area II was designed and constructed in 1948 specifically for the final assembly of the non-nuclear components of nuclear weapons, and was the primary site conducting such assembly until 1952. Both the architecture and location of the oldest buildings in the area reflect their original purpose. Assembly activities continued in Area II from 1952 to 1957, but the major responsibility for this work shifted to other sites in the Atomic Energy Commission`s integrated contractor complex. Gradually, additional buildings were constructed and the original buildings were modified. After 1960, the Area`s primary purpose was the research and testing of high-explosive components for nuclear weapons. In 1994, Sandia constructed new facilities for work on high-explosive components outside of the original Area II diamond-shaped parcel. Most of the buildings in the area are vacant and Sandia has no plans to use them. They are proposed for decontamination and demolition as funding becomes available.

  16. 高比表面空心球状ZnO/ZnAl2O4复合光催化剂制备及活性%Preparation and Photocatalytic Property of Hollow Sphere-Like ZnO/ZnAl2O4 Composite Photocatalysts with High Specific Surface Area

    Institute of Scientific and Technical Information of China (English)

    张丽; 阎建辉; 周民杰; 杨亚辉; 刘又年

    2012-01-01

    ZnO/ZnAl2O4 composite photocatlysts were prepared via one-pot hydrothermal process by using glucose as template and polyethylene glycol (PEG-4000) as dispersion agent after calcination at 500 X. For 4 h. The as-prepared samples were characterized by XRD, SEM, TEM, BET, TG/DT and UV-Vis DRS. The results indicated that the prepared ZnO/ZnAl2O4 composite photocatalyst showed hollow microspheres shape with high specific surface area. The photocatalytic activities of the as-obtained samples were evaluated by the degradation of Methyl Orange (MO) in aqueous solution under simulated sunlight irradiation The effects of calcination temperature, pH value and amount of PEG on the photocatalytic degradation efficiency of MO were investigated. The results showed that the highest photocatalytic degradation efficiency was observed at 10wt.% mass ratio of PEG to ZnO/ ZnAl2O4 and pH value of 9 in the starting materials. The maximum photocatalytic decoloration rate of MO was 98.7% within 60 min at 0.5 g·L-1 concentration of photocatlyst, which increased by 7.7% compared to that of TiO2 Degussa P-25 under the same conditions.%以葡萄糖为模板,聚乙二醇(PEG-4000)为分散剂通过一步水热法所得前驱体,经500℃焙烧4h得到ZnO/ZnAl2O4产物.并用XRD、SEM、TEM、BET、TG/DTA和UV-Vis DRS等技术对样品进行表征.结果表明产物为空心球状ZnO/ZnAl2O4复合光催化剂,比表面积高达158.3 m2·g-1.在模拟太阳光照射下,以甲基橙溶液的光催化降解考察样品的光催化活性,研究了焙烧温度、pH值和PEG加入量对样品光催化活性的影响.结果表明,当pH=9,PEG加入量为10%(以反应理论得到的前驱体ZnO/ZnAl2O4的质量来衡量)时,光催化活性最佳,光照60 min后,0.5 g·L-1光催化剂用量对甲基橙的脱色率达98.7%,与TiO2 Degussa P-25进行比较,相同条件下对甲基橙的脱色率提高了7.7%.

  17. Study of the areas and thicknesses of mesiobucal root canals prepared by three endodontic techniques Estudo das áreas e espessuras de canais radiculares mésio-vestibulares preparados por três técnicas endodônticas

    Directory of Open Access Journals (Sweden)

    Isa Geralda Teixeira Constante

    2007-06-01

    Full Text Available The purpose of this study was to compare, in vitro, by means of computerized analysis of digital radiographic images, the anatomic alterations produced in the mandibular molar tooth dentinal walls of mesiobucal canals with severe curvature by three different endodontic techniques: Progressive Preparation, Staged and Serial Preparation. A selection was made of 45 extracted, human, mandibular molars, with root curvatures greater than 25°. They were divided into three groups for every technique studied, which were then sub-divided into three sub-groups in accordance with the position of the curvature along the root: cervical, median or apical. After access surgery and tooth length determination, the canals were filled with 100% Barium Sulphate radiological contrast and the teeth were then radiographed with a direct digital radiography system, using a special apparatus capable of keeping the samples in the same spatial position during the different radiographic takes. After the above-mentioned endodontic techniques had been performed, the teeth were again filled with Barium sulphate and were also radiographed under the same previously mentioned conditions. The pre- and post-operative digital images were then analyzed in two computerized programs, AutoCAD 2004 and CorelDraw 10, to assess, respectively, the areas and the horizontal alterations which occurred in the internal and external walls of the root canals. The results indicated that although no significant differences among the techniques were shown in the statistical analysis, in a descriptive analysis the Progressive Preparation technique was shown to be more regular, uniform and effective.Objetivou-se comparar, in vitro, através de análise computadorizada de imagens radiográficas digitais, as alterações anatômicas promovidas nas paredes dentinárias de canais mésio-vestibulares com curvatura severa de molares inferiores por três técnicas endodônticas diferentes: Preparo Progressivo

  18. Preparation of Fe3O4/P(GMA-co-EGDMA) magnetic composite microspheres with high specific surface area by deposition of porous template%模板沉积法制备大孔高比表面积Fe3O4/P( GMA-co-EGDMA)磁性复合微球

    Institute of Scientific and Technical Information of China (English)

    张宝亮; 张秋禹; 张和鹏; 范新龙; 厉向杰; 雷星锋

    2012-01-01

    A simple method for preparation of Fe3O4/P ( GMA-co-EGDMA) magnetic composite microspheres using microporous P(GMA-co-EGDMA) microspheres copolymerized with glycidyl methacrylate (GMA) and ethylene glycol dimethacrylate (EGDMA) as template is reported in this paper. The preparation process included soaking of ferrous ion and ferric ion and coprecipitation in the presence of OH" . The influences of soaking temperature, soaking time, coprecipitation temperature and deposition times on magnetic content of magnetic composite microspheres were studied. The optimum preparation process of microporous Fe3O4/P (GMA-co-EGDMA) magnetic composite microspheres was as follows: microporous P (GMA-co-EGDMA) microspheres were soaked at 50°Cfor 4 h, coprecipitation temperature and time were 70°C and 1 h respectively. The magnetic content of magnetic composite microsphereswas 45. 24% when the deposition process was repeated 4 times. The morphology, magnetic properties, magnetic content, pore performance and particle size distribution of Fe3O4/P (GMA-co-EGDMA) were determined by SEM, TGA, XRD, mercury porosimeter and laser particle sizer. It was found that the range of particle size of Fe3O4/P (GMA-co-EGDMA) was 100~200 jmm and average particle size was 162 j^m, specific saturation magnetization was 10. 92 emu ? G~J , average pore diameter and specific surface area were 60 nm and 116 m2 ? G"1 respectively.%介绍了一种以大孔高比表面积甲基丙烯酸缩水甘油酯(GMA)与二甲基丙烯酸乙二醇酯(EGDMA)共聚交联微球[P(GMA-co-EGDMA)]为模板制备磁性复合微球的简单方法.制备过程包括Fe3+和Fe2+的浸入、OH-作用下孔内铁离子的共沉淀两步.在此过程中考察了浸泡温度、浸泡时间、共沉淀温度以及沉积次数对微球磁含量的影响,确定最佳制备工艺为50℃浸泡4h,70℃反应1h,如此反复4次磁含量可以达到45.24%.并通过SEM、VSM、XRD、TGA及压汞仪、激光粒度仪等手段对Fe3O4/P( GMA

  19. Roles of Principals in the Preparing Students to Life

    Science.gov (United States)

    Arslan, Hasan; Bingul, Murat

    2006-01-01

    This article explores the impacts of school leaders on the school curriculums of preparing students to life. Even if the school leaders and teachers are expert in their area related to the functions of the schools, it seems that schools are failing in the preparation of the students to life. The school leaders may play an important role to…

  20. 9 CFR 108.3 - Preparation of plot plans.

    Science.gov (United States)

    2010-01-01

    ... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Preparation of plot plans. 108.3... LICENSED ESTABLISHMENTS § 108.3 Preparation of plot plans. Plot plans shall show all of the buildings on a... on the plot plan the use of immediate adjacent properties such as, residential area, pasture,...

  1. Access cavity preparation.

    Science.gov (United States)

    Adams, N; Tomson, P L

    2014-03-01

    Each stage of root canal treatment should be carried out to the highest possible standard. The access cavity is arguably the most important technical stage, as subsequent preparation of the root canal(s) can be severely comprised if this is not well executed. Inadequate access can lead to canals being left untreated, poorly disinfected, difficult to shape and obturate, and may ultimately lead to the failure of the treatment. This paper highlights common features in root canal anatomy and outlines basic principles for locating root canals and producing a good access cavity. It also explores each phase of the preparation in detail and offers suggestions of instruments that have been specifically designed to overcome potential difficulties in the process. Good access design and preparation will result in an operative environment which will facilitate cleaning, shaping and obturation of the root canal system in order to maximise success.

  2. Preparation of hydrophobic coatings

    Science.gov (United States)

    Branson, Eric D.; Shah, Pratik B.; Singh, Seema; Brinker, C. Jeffrey

    2009-02-03

    A method for preparing a hydrophobic coating by preparing a precursor sol comprising a metal alkoxide, a solvent, a basic catalyst, a fluoroalkyl compound and water, depositing the precursor sol as a film onto a surface, such as a substrate or a pipe, heating, the film and exposing the film to a hydrophobic silane compound to form a hydrophobic coating with a contact angle greater than approximately 150.degree.. The contact angle of the film can be controlled by exposure to ultraviolet radiation to reduce the contact angle and subsequent exposure to a hydrophobic silane compound to increase the contact angle.

  3. Preparing for climate change.

    Science.gov (United States)

    Holdgate, M

    1989-01-01

    chlorofluorocarbons (CFCs) have been released in great quantities through their use in aerosol sprays, refrigerator fluids, and insulating foams. We can get rid of CFCs and curb the pollutants generating ozone, but it will be difficult to put the brake on either methane or nitrous oxide. And the reduction in carbon dioxide emissions will demand major changes in energy policy as well as action to slow deforestation. It appears that we are already committed to rising temperatures and sea levels. The question is by how much, in which areas? A number of things can be done to prepare for these changes: Governments must recognize that there is a problem; Better models must be worked out, especially to define where the greatest impacts from climate change and sea level rise will hit; Reference scenarios must be developed to see what the impacts are likely to be in ecological, agricultural, social and economic terms; Every country should develop "avoidance strategies" to minimize risk (for example, by not building on land likely to be flooded); We must cut down on the amount of greenhouse gases released into the atmosphere from human activities, by eliminating CFCs and adopting energy conservation programs and other measures to minimize CO2 release; Global agreements to protect the atmosphere are needed.

  4. Sperm preparation for fertilization

    NARCIS (Netherlands)

    Gadella, B.M.

    2014-01-01

    Description This book contains 19 chapters that discuss theoretical and applied andrology for domestic, zoo and wild animals. Topics include semen and its constituents; sperm production and harvest; determinants of sperm morphology; sperm preparation for fertilization; practical aspects of semen cry

  5. Preparation and evaluation of sulfided NiMo/γ-Al2O3 hydrotreating catalysts

    OpenAIRE

    KAMYAB, ALI

    2016-01-01

      Four nickel-molybdenum catalysts were synthesized on gamma alumina with higher surface area and on NiMo catalyst was prepared using gamma alumina with lower surface area. Catalysts with higher-surface-area support were prepared by co-impregnation, sequential impregnation and adding phosphorous. Theses catalysts were calcined at 500  ͦC. Effect of higher calcination temperature was investigated by preparation of one catalyst calcined at 700 ͦC. Catalysts were thoroughly characterized via fou...

  6. FHFA Underserved Areas

    Data.gov (United States)

    Department of Housing and Urban Development — Federal Housing Finance Agency's (FHFA) Underserved Areas establishes underserved area designations for census tracts in Metropolitan Areas (MSAs), nonmetropolitan...

  7. Neural correlates of mental preparation for successful insight problem solving.

    Science.gov (United States)

    Tian, F; Tu, S; Qiu, J; Lv, J Y; Wei, D T; Su, Y H; Zhang, Q L

    2011-01-20

    A distinct type of mental preparation (activity in medial frontal and temporal areas) had been found to facilitate insight problem solving independent of specific problems [25]. In order to explore whether neural activity during a preparatory interval (mental preparation) is associated with which insight problems would be solved or not, we developed a task that uses Chinese logogriphs (riddles) as materials. Blood oxygenation level-dependent fMRI contrasts between Successful and Unsuccessful mental preparation were measured. Results showed that mental preparation leading to successful problem solving involves heightened activity in the left middle/medial frontal gyrus, the left middle/superior temporal gyrus, the right cerebellum, the bilateral claustrum and the left postcentral gyrus. We discussed the role of these areas in mental preparation for successful insight problem solving.

  8. Preparation for Retirement Seminar

    CERN Multimedia

    HR Department

    2009-01-01

    The Human Resources Department is organizing a preparation for retirement seminar, which will take place on the afternoons of the 11, 13, 25 and 27 November 2009. Similar seminars in the past have always proved highly successful. Retirement marks the end of a person’s working life and the start of a new chapter. This period of transition is experienced differently from one individual to another. In all cases, being well-informed and prepared greatly facilitates the change in lifestyle. We would like to draw your attention to the following information: Staff concerned: All staff members aged 58 and above have been sent a personal invitation to attend. Spouses are welcome. Staff members below 58 who are interested in attending the seminar may also apply. Their applications will be accepted subject to availability of places. Registration: In view of the number of people concerned and the limited capacity of the main auditorium, you are requested to register in advance via ...

  9. Preparation for Retirement Seminar

    CERN Multimedia

    HR Department

    2009-01-01

    The Human Resources Department is organizing a preparation for retirement seminar, which will take place in the afternoons of 11, 13, 25 and 27 November 2009. Similar seminars in the past have always proved highly successful. Retirement marks the end of a person’s working life and the start of a new chapter. This period of transition is experienced differently from one individual to another. In all cases, being well-informed and prepared greatly facilitates the change in lifestyle. We would like to draw your attention to the following information: Staff concerned: All staff members aged 58 and above have been sent a personal invitation to attend. Spouses are welcome. Staff members below 58 who are interested in attending the seminar may also apply. Their applications will be accepted subject to the availability of places. Registration: In view of the number of people concerned and the limited capacity of the Main Auditorium, you are requested to register in advance via Ind...

  10. Preparation for Retirement Seminar

    CERN Multimedia

    HR Department

    2009-01-01

    The Human Resources Department is organizing a preparation for retirement seminar, which will take place on the afternoons of the 11, 13, 25 and 27 November 2009. Similar seminars in the past have always proved highly successful. Retirement marks the end of a person’s working life and the start of a new chapter. This period of transition is experienced differently from one individual to another. In all cases, being well-informed and prepared greatly facilitates the change in lifestyle. We would like to draw your attention to the following information: Staff concerned: All staff members aged 58 and above have been sent a personal invitation to attend. Spouses are welcome. Staff members below 58 who are interested in attending the seminar may also apply. Their applications will be accepted subject to the availability of places. Registration: In view of the number of people concerned and the limited capacity of the Main Auditorium, you are requested to register in advance ...

  11. Preparation for Retirement Seminar

    CERN Multimedia

    HR Department

    2009-01-01

    The Human Resources Department is organizing a preparation for retirement seminar, which will take place on the afternoons of the 11, 13, 25 and 27 November 2009. Similar seminars in the past have always proved highly successful. Retirement marks the end of a person’s working life and the start of a new chapter. This period of transition is experienced differently from one individual to another. In all cases, being well-informed and prepared greatly facilitates the change in lifestyle. We would like to draw your attention to the following information: Staff concerned: All staff members aged 58 and above have been sent a personal invitation to attend. Spouses are welcome. Staff members under the age of 58 who are interested in attending the seminar may also apply. Their applications will be accepted subject to the availability of places. Registration: In view of the number of people concerned and the limited capacity of the Main Auditorium, you are requested to register ...

  12. Preparations, models, and simulations.

    Science.gov (United States)

    Rheinberger, Hans-Jörg

    2015-01-01

    This paper proposes an outline for a typology of the different forms that scientific objects can take in the life sciences. The first section discusses preparations (or specimens)--a form of scientific object that accompanied the development of modern biology in different guises from the seventeenth century to the present: as anatomical-morphological specimens, as microscopic cuts, and as biochemical preparations. In the second section, the characteristics of models in biology are discussed. They became prominent from the end of the nineteenth century onwards. Some remarks on the role of simulations--characterising the life sciences of the turn from the twentieth to the twenty-first century--conclude the paper.

  13. Preparation for Retirement Seminar

    CERN Multimedia

    HR Department

    2009-01-01

    The Human Resources Department is organizing a preparation for retirement seminar, which will take place on the afternoons of the 11, 13, 25 and 27 November 2009. Similar seminars in the past have always proved highly successful. Retirement marks the end of a person’s working life and the start of a new chapter. This period of transition is experienced differently from one individual to another. In all cases, being well-informed and prepared greatly facilitates the change in lifestyle. We would like to draw your attention to the following information: Staff concerned: All staff members aged 58 and above have been sent a personal invitation to attend. Spouses are welcome. Staff members under the age of 58 who are interested in attending the seminar may also apply. Their applications will be accepted subject to the availability of places. Registration: In view of the number of people concerned and the limited capacity of the Main Auditorium, you are requested to register ...

  14. Preparation for Retirement Seminar

    CERN Multimedia

    HR Department

    2009-01-01

    The Human Resources Department is organizing a preparation for retirement seminar, which will take place on the afternoons of the 11, 13, 25 and 27 November 2009. Similar seminars in the past have always proved highly successful. Retirement marks the end of a person’s working life and the start of a new chapter. This period of transition is experienced differently from one individual to another. In all cases, being well-informed and prepared greatly facilitates the change in lifestyle. We would like to draw your attention to the following information: Staff concerned: All staff members aged 58 and above have been sent a personal invitation to attend. Spouses are welcome. Staff members below 58 who are interested in attending the seminar may also apply. Their applications will be accepted subject to the availability of places. Registration: In view of the number of people concerned and the limited capacity of the Main Auditorium, you are requested to register in advance ...

  15. Preparation of mullite fiber

    Energy Technology Data Exchange (ETDEWEB)

    Chen, L.; Wang, B.; Liu, S.; Yan, Y. [Xiamen Univ. (China). Dept. of Chemistry

    1996-06-01

    Transparent mullite fibers have been prepared using aluminum carboxylates (ACs) and tetraethyl orthosilicate (TEOS) as starting materials. The ACs are derived from the catalyzed dissolution of elemental aluminum in a mixture of formic acid and acetic acid. The solubility of aluminum in the acids is influenced by the concentrations of the acids, water, and additives and the preparation temperature. A 1:4:3:24 molar ratio of aluminum, formic acid, acetic acid, and water dissolves the aluminum completely to give a colorless, clear solution suitable for fiber synthesis. The mixture of the ACs and TEOS, in the presence of ethyl alcohol as a mutual solvent at 50--60 C, is concentrated to give a spinnable dope, from which mullite precursor fibers can be drawn. Heat treatment of the precursor at 1,250 C yields crystallized and transparent mullite fibers.

  16. Preparation for Physics Redux

    Science.gov (United States)

    Adelson, Edward

    2006-12-01

    The textbook for our preparation for physics course has been rewritten ab initio. Like its predecessor, it adapts a spiral approach to dealing with preconceptions, but this version encourages work at higher levels in Bloom's taxonomy and makes students sensitive to how p-prims affect their understanding. As its title: "All in Proportion: Preparation for Physics" indicates, it emphasizes how far proportional reasoning will take the student. Classwork is mainly group work, and various techniques are used to encourage students to complete the learning cycle on material that has not been mastered. Both the FCI and the Lawson "Classroom Test of Scientific Reasoning" have been given to gauge student progress. Preliminary results will be reported and sample materials will be shown.

  17. Class 1 Areas

    Data.gov (United States)

    U.S. Environmental Protection Agency — A "Class 1" area is a geographic area recognized by the EPA as being of the highest environmental quality and requiring maximum protection. Class I areas are areas...

  18. The Pharmacokinetics and Pharmacodynamics of Iron Preparations

    Directory of Open Access Journals (Sweden)

    Susanna Burckhardt

    2011-01-01

    Full Text Available Standard approaches are not appropriate when assessing pharmacokinetics of iron supplements due to the ubiquity of endogenous iron, its compartmentalized sites of action, and the complexity of the iron metabolism. The primary site of action of iron is the erythrocyte, and, in contrast to conventional drugs, no drug-receptor interaction takes place. Notably, the process of erythropoiesis, i.e., formation of new erythrocytes, takes 3−4 weeks. Accordingly, serum iron concentration and area under the curve (AUC are clinically irrelevant for assessing iron utilization. Iron can be administered intravenously in the form of polynuclear iron(III-hydroxide complexes with carbohydrate ligands or orally as iron(II (ferrous salts or iron(III (ferric complexes. Several approaches have been employed to study the pharmacodynamics of iron after oral administration. Quantification of iron uptake from radiolabeled preparations by the whole body or the erythrocytes is optimal, but alternatively total iron transfer can be calculated based on known elimination rates and the intrinsic reactivity of individual preparations. Degradation kinetics, and thus the safety, of parenteral iron preparations are directly related to the molecular weight and the stability of the complex. High oral iron doses or rapid release of iron from intravenous iron preparations can saturate the iron transport system, resulting in oxidative stress with adverse clinical and subclinical consequences. Appropriate pharmacokinetics and pharmacodynamics analyses will greatly assist our understanding of the likely contribution of novel preparations to the management of anemia.

  19. The pharmacokinetics and pharmacodynamics of iron preparations.

    Science.gov (United States)

    Geisser, Peter; Burckhardt, Susanna

    2011-01-04

    Standard approaches are not appropriate when assessing pharmacokinetics of iron supplements due to the ubiquity of endogenous iron, its compartmentalized sites of action, and the complexity of the iron metabolism. The primary site of action of iron is the erythrocyte, and, in contrast to conventional drugs, no drug-receptor interaction takes place. Notably, the process of erythropoiesis, i.e., formation of new erythrocytes, takes 3-4 weeks. Accordingly, serum iron concentration and area under the curve (AUC) are clinically irrelevant for assessing iron utilization. Iron can be administered intravenously in the form of polynuclear iron(III)-hydroxide complexes with carbohydrate ligands or orally as iron(II) (ferrous) salts or iron(III) (ferric) complexes. Several approaches have been employed to study the pharmacodynamics of iron after oral administration. Quantification of iron uptake from radiolabeled preparations by the whole body or the erythrocytes is optimal, but alternatively total iron transfer can be calculated based on known elimination rates and the intrinsic reactivity of individual preparations. Degradation kinetics, and thus the safety, of parenteral iron preparations are directly related to the molecular weight and the stability of the complex. High oral iron doses or rapid release of iron from intravenous iron preparations can saturate the iron transport system, resulting in oxidative stress with adverse clinical and subclinical consequences. Appropriate pharmacokinetics and pharmacodynamics analyses will greatly assist our understanding of the likely contribution of novel preparations to the management of anemia.

  20. [Microflora of spiruline preparations].

    Science.gov (United States)

    Jacquet, J

    1975-01-01

    A study, by direct microscopic examination and cultures, shows that the microflore which accompanies the spirulines preparations, varies as the origin and the technologie treatment quality. The main species are bacillacees; then, come faecal streptococcus which are the best contaminations indicators; enterobacteries, yeasts, moulds spores, are exceptional. Dry products as getting old, entail a great decrease of all the species, the anaerobies being more resistant.

  1. The Preparation of Graphene

    Institute of Scientific and Technical Information of China (English)

    Chen Yanyan

    2015-01-01

    Graphene has unique structure and possesses excellent physical and chemical properties, and it has received a great deal of attention in related research fields. The quality, quantity and application of graphene are related to its preparation methods. At present the bottleneck of graphene research is that both high-quality and large quantity of graphene could not be obtained simultaneously and the reason is that the basic mechanism of graphene formation has mot been wel understood.

  2. Preparation of chitosan gel

    Directory of Open Access Journals (Sweden)

    Lagerge S.

    2012-06-01

    Full Text Available Aerogel conditioning of the chitosan makes it possible to prepare porous solids of significant specific surface. The increase in the chitosan concentration or the degree of acetylation decreases the specific surface of the synthesized chitosan gel. Whereas drying with supercritical CO2 more effectively makes it possible to preserve the volume of the spheres of gel and to have a more significant specific surface in comparison with evaporative drying.

  3. Facility Effluent Monitoring Plan determinations for the 600 Area facilities

    Energy Technology Data Exchange (ETDEWEB)

    Nickels, J.M.

    1991-08-01

    This document determines the need for Facility Effluent Monitoring Plans for Westinghouse Hanford Company's 600 Area facilities on the Hanford Site. The Facility Effluent Monitoring Plan determinations were prepared in accordance with A Guide For Preparing Hanford Site Facility Effluent Monitoring Plans (WHC 1991). Five major Westinghouse Hanford Company facilities in the 600 Area were evaluated: the Purge Water Storage Facility, 212-N, -P, and -R Facilities, the 616 Facility, and the 213-J K Storage Vaults. Of the five major facilities evaluated in the 600 Area, none will require preparation of a Facility Effluent Monitoring Plan.

  4. Physiologic effects of bowel preparation

    DEFF Research Database (Denmark)

    Holte, Kathrine; Nielsen, Kristine Grubbe; Madsen, Jan Lysgård;

    2004-01-01

    as increased phosphate and urea concentrations, whereas calcium and potassium concentrations decreased significantly after bowel preparation. No differences in plasma or extracellular volumes were seen. Orthostatic tolerance and balance function did not change after bowel preparation. CONCLUSIONS: Bowel...

  5. Preparing for Emergency Situations

    Science.gov (United States)

    Asproth, Viveca; Amcoff Nyström, Christina

    2010-11-01

    Disaster relief can be seen as a dynamic multi actor process with actors both joining and leaving the relief work during the help and rescue phase after the disaster has occurred. Actors may be governmental agencies, non profit voluntary organisations or spontaneous helpers comprised of individual citizens or temporal groups of citizens. Hence, they will vary widely in agility, competence, resources, and endurance. To prepare for for disasters a net based Agora with simulation of emergency situations for mutual preparation, training, and organisational learning is suggested. Such an Agora will ensure future security by: -Rising awareness and preparedness of potential disaster responders by help of the components and resources in the netAgora environment; -Improving cooperation and coordination between responders; -Improving competence and performance of organisations involved in security issues; -Bridging cultural differences between responders from different organizations and different backgrounds. The developed models are intended to reflect intelligent anticipatory systems for human operator anticipation of future consequences. As a way to catch what should be included in this netbased Agora and to join the split pictures that is present, Team Syntegrity could be a helpful tool. The purpose of Team Syntegrity is to stimulate collaboration and incite cross fertilization and creativity. The difference between syntegration and other group work is that the participants are evenly and uniquely distributed and will collectively have the means, the knowledge, the experience, the perspectives, and the expertise, to deal with the topic. In this paper the possibilities with using Team Syntegrity in preparation for the development of a netbased Agora is discussed. We have identified that Team Syntegrity could be useful in the steps User Integration, Designing the netAgora environment, developing Test Scenarios, and assessment of netAgora environment.

  6. Micro-CT assessment of two different endodontic preparation systems

    Directory of Open Access Journals (Sweden)

    Cacio Moura-Netto

    2013-02-01

    Full Text Available The aim of this study was to compare two endodontic preparation systems using micro-CT analysis. Twenty-four one-rooted mandibular premolars were selected and randomly assigned to two groups. The samples (n = 12 of Group 1 were prepared using the ProTaper Universal rotary system, while Group 2 (n = 12 was prepared using the EndoEZE AET system complemented by manual apical preparation with K-type hand files up to #30. A 2.5% sodium hypochlorite solution was used in both groups for irrigating. Both groups were scanned by high-resolution microcomputed tomography before and after preparation (SkyScan 1172, SkyScan, Kontich, Belgium. The root canal volume and surface area was measured before and after preparation, and the differences were calculated and analyzed for statistically significant differences using ANOVA complemented by the Tukey test (p < 0.05. The results showed no statistically significant differences between the mean volumes of dentin removal by the two systems. However, the EndoEZE AET system presented a significantly greater mean surface area compared to the ProTaper system (p < 0.05. The EndoEZE AET system enabled preparation of a greater root canal surface area when compared to the ProTaper Universal system. There seemed to be no difference in dentin volume loss between the two systems used.

  7. Preparation of tungsten oxide

    Science.gov (United States)

    Bulian, Christopher J.; Dye, Robert C.; Son, Steven F.; Jorgensen, Betty S.; Perry, W. Lee

    2009-09-22

    Tungsten trioxide hydrate (WO.sub.3.H.sub.2O) was prepared from a precursor solution of ammonium paratungstate in concentrated aqueous hydrochloric acid. The precursor solution was rapidly added to water, resulting in the crash precipitation of a yellow white powder identified as WO.sub.3.H.sub.2O nanosized platelets by x-ray diffraction and scanning electron microscopy. Annealing of the powder at 200.degree. C. provided cubic phase WO.sub.3 nanopowder, and at 400.degree. C. provided WO.sub.3 nanopowder as a mixture of monoclinic and orthorhombic phases.

  8. End-preparation assessments and tests for compounded sterile preparations.

    Science.gov (United States)

    McElhiney, Linda F

    2013-01-01

    Outsourcing has become a necessity to obtain sterile products that are currently on backorder. Because of the expense of outsourcing sterile compounding, pharmacy leadership in health systems are now considering the option of insourcing and batch preparing compounded sterile preparations, which can be a viable option for a health system. It can significantly decrease drug-spending costs, and the pharmacy has a complete record of the compounding process. The key to preparing high-quality, safe, sterile preparations and meeting United States Pharmacopeia standards is end-preparation assessments and tests.

  9. Area Handbook for Senegal. Second Edition.

    Science.gov (United States)

    Nelson, Harold D.; And Others

    This volume on Senegal is one of a series of handbooks prepared by Foreign Area Studies (FAS) of the American University. It is designed to be useful to military and other personnel who need a convenient compilation of basic facts about the social, economic, political, and military institutions and practices of Senegal. The emphasis is on…

  10. Lighting outside built-up areas.

    NARCIS (Netherlands)

    Asmussen, E.

    1965-01-01

    Lezing gehouden op 21/26 september in London 1964 handelend over verlichting buiten de bebouwde kom. (Engelse versie). Shortened version of the paper on Lighting of roads outside built-up areas prepared for theme III, Ways of reducing the Frequency of accidents, discussed at the International Study

  11. Prepare Healthy Foods with Toddlers

    Science.gov (United States)

    Izumi-Taylor, Satomi; Rike, Cheryl

    2011-01-01

    Toddlers--from about 16 to 36 months--can learn a variety of skills as they prepare food and follow recipes in developmentally appropriate ways. Early childhood teachers are encouraged to support young children's healthy eating habits by offering simple food preparation experiences. When toddlers--and preschoolers--safely prepare healthy snacks,…

  12. Why Specialized Preparation is Critical.

    Science.gov (United States)

    McEwin, C. Kenneth; Dickinson, Thomas S.; Smith, Tracy W.

    2003-01-01

    Asserts that mandating specific teacher preparation programs may be necessary to ensure that teachers are adequately prepared for the unique challenges and rewards of teaching young adolescents, discussing: the desirability of teacher young adolescents, important elements of teacher preparation, the need for tighter licensure requirements, and the…

  13. Preparation for Retirement Seminar

    CERN Multimedia

    HR Department

    2007-01-01

    The Department of Human Resources is organising a preparation for retirement seminar which will take place on the four successive afternoons of 2 to 5 October 2007. Similar seminars in the past have always proved highly successful. Retirement marks the end of one’s working life and the start of a new period of life. This period of transition and change is experienced differently from one individual to another. In any case, being well-informed and prepared greatly facilitates the change in lifestyle. We would like to draw your attention to the following information: Staff concerned: All staff members aged 58 and above as well as those who have retired during the year have been sent a personal invitation to attend. Spouses are welcome. Staff members below 58 who are interested in attending the seminar may also apply. Their applications will be accepted subject to availability of places. Registration: In view of the number of people concerned and the limited capacity of th...

  14. Preparation for retirement seminar

    CERN Multimedia

    HR Department

      The Human Resources Department is organizing a preparation for retirement seminar, which will take place on the afternoons of the 25 and 27 November 2009. Similar seminars in the past have always proved highly successful. Retirement marks the end of a person’s working life and the start of a new chapter. This period of transition is experienced differently from one individual to another. In all cases, being well-informed and prepared greatly facilitates the change in lifestyle. We would like to draw your attention to the following information: Staff concerned: All staff members aged 58 and above have been sent a personal invitation to attend. Spouses are welcome. Staff members under the age of 58 who are interested in attending the seminar may also apply. Their applications will be accepted subject to the availability of places. Registration: In view of the number of people concerned and the limited capacity of the Main Auditorium, you are requested to register in advance via Indico. &a...

  15. Preparation for Retirement Seminar

    CERN Multimedia

    HR Department

    2011-01-01

    The Human Resources Department is organizing a Preparation for Retirement Seminar, which will take place on 18 and 21 October 2011 in the afternoon in the Main Auditorium and on 19 October and 15 and 16 November 2011 in the afternoon in the Council Chamber. Similar seminars in the past have always proved highly successful. Retirement marks the end of a person’s working life and the start of a new chapter. This period of transition is experienced differently from one individual to another. In all cases, being well-informed and prepared greatly facilitates the change in lifestyle. We would like to draw your attention to the following information: Staff concerned: All staff members aged 58 and above have been sent a personal invitation to attend. Spouses are welcome. Staff members under the age of 58 who are interested in attending the seminar may also apply. Their applications will be accepted subject to availability of places. Registration: In view of the number of people concerned, you are ...

  16. Preparation for Retirement Seminar

    CERN Multimedia

    HR Department

    2011-01-01

    The Human Resources Department is organizing a Preparation for Retirement Seminar, which will take place on 18 and 21 October 2011 in the afternoon in the Main Auditorium and on 19 October and 15 and 16 November 2011 in the afternoon in the Council Chamber. Similar seminars in the past have always proved highly successful. Retirement marks the end of a person’s working life and the start of a new chapter. This period of transition is experienced differently from one individual to another. In all cases, being well-informed and prepared greatly facilitates the change in lifestyle. We would like to draw your attention to the following information: Staff concerned: All staff members aged 58 and above have been sent a personal invitation to attend. Spouses are welcome. Staff members under the age of 58 who are interested in attending the seminar may also apply. Their applications will be accepted subject to availability of places. Registration: In view of the number of people concerned, you are r...

  17. PREPARATION FOR RETIREMENT PROGRAMME

    CERN Multimedia

    Human Resources Division

    2001-01-01

    27 March 2001 from 2.00 p.m. to 5.30 p.m. 28 March 2001 from 2.00 p.m. to 5.30 p.m. 29 March 2001 from 2.00 p.m. to 5.30 p.m. 30 March 2001 from 2.00 p.m. to 4.45 p.m. Auditorium (Main Building) After the success of the preparation seminars held in recent years, it has been decided that the programme should continue. The forthcoming seminar has been prepared in close collaboration with the CERN Pensioners' Association. The programme will be organised over several half-day sessions. Once again this year, a special session will be devoted to the 10th revision of the Swiss state pension scheme, the 'AVS' (Assurance-Vieillesse et Survivants), and the consequences for international civil servants. A talk will be given by Mrs Danièle Siebold, Director of the Caisse Cantonale Genevoise de Compensation, aimed mainly at those residing in or intending to move to Switzerland, or who worked in Switzerland before joining CERN. To enable Mrs Siebold to respond to your concerns as effectively as possible, please ...

  18. Data Breach Preparation

    Energy Technology Data Exchange (ETDEWEB)

    Belangia, David Warren [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-03-13

    The Home Depot Data Breach is the second largest data breach on record. It has or will affect up to 56 million debit or credit cards. A trusted vendor account, coupled with the use of a previously unknown variant of malware that allowed the establishment of a foothold, was the entry point into the Home Depot network. Once inside the perimeter, privilege escalation provided an avenue to obtain the desired information. Home Depot did, however, learn some lessons from Target. Home Depot certainly communicated better than Target, procured insurance, and instituted as secure an environment as possible. There are specific measures an institution should undertake to prepare for a data breach, and everyone can learn from this breach. Publicly available information about the Home Depot Data Breach provides insight into the attack, an old malware variant with a new twist.While the malware was modified as to be unrecognizable with tools, it probably should have been detected. There are also concerns with Home Depot’s insurance and the insurance provider’s apparent lack of fully reimbursing Home Depot for their losses. The effect on shareholders and Home Depot’s stock price was short lived. This story is still evolving but provides interesting lessons learned concerning how an organization should prepare for it inevitable breach.

  19. Instructions for Manuscript Preparation

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    Plasma Science and Technology (PST) is a joumal reporting novel experimental and theoretical results and progress of interdisciplinary and application sciences in the fields related to Plasma Physics. Specific interested areas include: basic plasma phenomena; magnetically confined plasma; inertially confined plasma; astrophysics and space plasma; low temperature plasma; plasma technology and fusion engineering.

  20. Instructions for Manuscript Preparation

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    Plasma Science and Technology (PST) is a journal reporting novel experimental and theoretical results and progress of interdisciplinary and application sciences in the fields related to Plasma Physics. Specific interested areas include: basic plasma phenomena; magnetically confined plasma; inertially confined plasma; astrophysics and space plasma; low temperature plasma; plasma technology and fusion engineering.

  1. Instructions for Manuscript Preparation

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    Plasma Science and Technology (PST) is a journal reporting novel experimental and theoretical results and progress of interdisciplinary and application sciences in the fields related to Plasma Physics. Specific interested areas include: basic plasma phenomena; magnetically confined plasma; inertially confined plasma; astrophysics and space plasma; low temperature plasma; plasma technology and fusion engineering.

  2. Instructions for Manuscript Preparation

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    Plasma Science and Technology (PST) is a joumal reporting novel experimental and theoretical results and progress of interdisciplinary and application sciences in the fields related to Plasma Physics. Specific interested areas include: basic plasma phenomena; magnetically confined plasma; inertially confined plasma; astrophysics and space plasma; low temperature plasma; plasma technology; fusion engineering and ion beam bioengineering.

  3. Instructions for Manuscript Preparation

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    Plasma Science and Technology (PST) is a journal reporting novel experimental and theoretical results and progress of interdisciplinary and application sciences in the fields related to Plasma Physics. Specific interested areas include: basic plasma phenomena; magnetically confined plasma; inertially confined plasma; astrophysics and space plasma; low temperature plasma; plasma technology; fusion engineering and ion beam bioengineering.

  4. Preparing the SPS tunnel

    CERN Multimedia

    1974-01-01

    The photo shows the area round PA3 where the mounting of the general electrical services and fluid services are now completed, waiting for the installation in a few days of the magnet supports and the bus bars which will feed power into the magnets. (See CERN Weekly Bulletin, week 40.)

  5. Preparing Students for Globalization

    DEFF Research Database (Denmark)

    Friesel, Anna

    2010-01-01

    : USA, China, Korea, Mexico, Chile and others. We describe our experiences of working on industrial projects with international teams and analyse the development and trends in student mobility. The growing popularity of these programmes and the increasing number of the students joining our international......A. Friesel. Preparing Students for Globalization Working with International Teams with Projects // Electronics and Electrical Engineering. - Kaunas: Technologija, 2019. - No. 6(102). - P. 111-114. This paper summarizes the activities, contents and overall outcomes of our experiences...... with international students studying at the Copenhagen University College of Engineering (in short - IHK); in particular students coming for one semester exchange program under Erasmus-programme. IHK's participation in EU-supported programmes like EIE-Surveyor and ELLEIEC, both ERASMUS thematic networks, have...

  6. Preparing for faster filling

    CERN Multimedia

    CERN Bulletin

    2010-01-01

    Following the programmed technical stop last week, operators focussed on preparing the machine for faster filling, which includes multibunch injection and a faster pre-cycle phase.   The LHC1 screen shot during the first multibunch injection operation. The LHC operational schedule incorporates a technical stop for preventive maintenance roughly every six weeks of stable operation, during which several interventions on the various machines are carried out. Last week these included the replacement of a faulty magnet in the SPS pre-accelerator, which required the subsequent re-setting of the system of particle extraction and transfer to the LHC. At the end of last week, all the machines were handed back for operation and work could start on accommodating all the changes made into the complex systems in order for normal operation to be resumed. These ‘recovery’ operations continued through the weekend and into this week. At the beginning of this week, operators succeeded in pro...

  7. Method to prepare Semtex

    Energy Technology Data Exchange (ETDEWEB)

    Alcaraz, A; Dougan, A

    2006-11-26

    This procedure requires the binder and uncoated RDX be prepared in separate steps, see Figure 1: (1) The binder and dye are mixed by agitation with a water-insoluble organic solvent (e.g., toluene), I; (2) The RDX/PETN is agitated thoroughly with water, II; (3) The binder solution I is added to the RDX/water mixture at II with thorough mixing to form a slurry III; (4) In the next step the solvent is distilled off at IV leaving resulting granules; (5) The next step is followed by filtration at V, which may be done by vacuum; (6) The composition is then dried at VI to a dough-like consistency.

  8. PREPARE: guidelines for planning animal research and testing.

    Science.gov (United States)

    Smith, Adrian J; Clutton, R Eddie; Lilley, Elliot; Hansen, Kristine E Aa; Brattelid, Trond

    2017-01-01

    There is widespread concern about the quality, reproducibility and translatability of studies involving research animals. Although there are a number of reporting guidelines available, there is very little overarching guidance on how to plan animal experiments, despite the fact that this is the logical place to start ensuring quality. In this paper we present the PREPARE guidelines: Planning Research and Experimental Procedures on Animals: Recommendations for Excellence. PREPARE covers the three broad areas which determine the quality of the preparation for animal studies: formulation, dialogue between scientists and the animal facility, and quality control of the various components in the study. Some topics overlap and the PREPARE checklist should be adapted to suit specific needs, for example in field research. Advice on use of the checklist is available on the Norecopa website, with links to guidelines for animal research and testing, at https://norecopa.no/PREPARE .

  9. Preparation of electrodes on cfrp composites with low contact resistance comprising laser-based surface pre-treatment

    KAUST Repository

    Almuhammadi, Khaled Hamdan

    2016-12-29

    Various examples are provided related to the preparation of electrodes on carbon fiber reinforced polymer (CFRP) composites with low contact resistance. Laser-based surface preparation can be used for bonding to CFRP composites. In one example, a method includes preparing a pretreated target area on a CFRP composite surface using laser pulsed irradiation and bonding an electrode to exposed fibers in the pretreated target area. The surface preparation can allow the electrode to have a low contact resistance with the CFRP composite.

  10. Preparing for events for physically challenged athletes.

    Science.gov (United States)

    Simon, Lauren M; Ward, David C

    2014-01-01

    The participation in sports for physically challenged athletes continues to expand in multiple domains from recreational, novice, and competitive to elite competitions such as the Paralympics. Physically challenged athletes have various disabilities such as visual impairments, spinal cord injuries, amputations, cerebral palsy, or other neuromuscular impairments and have different levels of functional ability within these broad categories. The spectrum of medical illnesses and musculoskeletal injuries seen with sports is similar to that of able-bodied athletes; however medical teams caring for athletes with disabilities need to be familiar with medical risks such as skin breakdown, thermoregulation problems, dehydration, autonomic dysreflexia, infections, orthotic and prosthetic issues, and psychiatric comorbidities that may be encountered. The medical team preparation for events involving physically challenged athletes should include obtaining appropriate medical supplies, ensuring disability-compatible access to medical areas, and preparing for emergency extraction from adaptive equipment.

  11. Preparation of coal slurry with organic solvents.

    Science.gov (United States)

    Shin, Yu-Jen; Shen, Yun-Hwei

    2007-06-01

    In this study, various organic solvents were used to prepare coal slurries and the rheological and thermal properties of coal-organic solvent slurries were examined. Solvents with molecules containing unpaired electrons (high basicity) show high extraction power and cause swelling of coal. Therefore, coal-organic solvent slurries usually showed higher viscosities compared to coal-water slurry. In addition, coal slurries prepared by alcohols and cyclohexanone demonstrated lower settling rates but a high specific sedimentation volume presumably because these solvents swelled coal particles well and led to the formation of weak gel structures in the bulk. In addition, ethanol and cyclohexanone are capable of breaking a considerable amount of hydrogen bonds in coal and subsequently opening up the structures. Thus, more surface area is available for combustion and the combustion rate of coal slurries was increased.

  12. Photochemical preparation and application research of Au nanoparticles

    Institute of Scientific and Technical Information of China (English)

    DONG; Shou-an; SUN; Jia-lin

    2005-01-01

    Gold nanoparticles protected by organic small molecular compounds or macromolecule have attracted considerable attention and their preparation is one of hotspots in the nano-chemical material field due to their ongoing and potential applications in optics, electronics, catalysts and biosensors. In recent years there are many liquid phase chemistry methods to prepare monodispersed gold particles. Among them, the photochemical method is quite attractive because of its some important advantages for size-controlled synthesis of gold nanoparticles. Therefore, in this paper the recert progress of the photochemical preparing Au nanoparticle materials was briefly introduced and mainly emphasized authors' own works of this area.

  13. Food preparation supplies predict children's family meal and home-prepared dinner consumption in low-income households.

    Science.gov (United States)

    Appelhans, Bradley M; Waring, Molly E; Schneider, Kristin L; Pagoto, Sherry L

    2014-05-01

    Frequent family meals and home food preparation are considered important for children's nutritional health and weight maintenance. This cross-sectional study tested whether these parent-driven behaviors are related to the availability of food preparation supplies in low-income urban households. Caregivers of children ages 6-13 provided information on family meal frequency, child consumption of home-prepared dinners, household food insecurity, and attitudes towards cooking. Researchers used a newly developed Food Preparation Checklist (FPC) to assess the availability of 41 food preparation supplies during a physical audit of the home environment. Caregivers and children provided anthropometric measurements and jointly reported on child dietary intake. In ordinal logistic regression models, greater home availability of food preparation supplies was associated with more frequent family meals and child consumption of home-prepared dinners. Associations were independent of household financial strain, food insecurity, caregiver attitudes toward cooking, and sociodemographic characteristics. Fewer food preparation supplies were available in households characterized by greater food insecurity, lower income, and negative caregiver attitudes towards cooking, but did not differ by child or caregiver weight status. As in prior studies, more frequent family meals and consumption of home-prepared dinners were associated with healthier child dietary intake in several areas. We conclude that food preparation supplies are often limited in the most socioeconomically disadvantaged households, and their availability is related to the frequency with which children consume family meals and home-prepared dinners. The potential role of food preparation supplies as contributors to socioeconomic disparities in child nutritional health and obesity deserves further study. Copyright © 2014 Elsevier Ltd. All rights reserved.

  14. Premedication, preparation, and surveillance.

    Science.gov (United States)

    Bell, G D

    2002-01-01

    peppermint oil, as well as the value of variable-stiffness colonoscopes, in reducing the need for intravenous sedation is discussed. Case reports of hyponatraemic encephalopathy and hypocalcaemic tetany as complications of oral bowel preparation are presented, as is the challenge associated with adequate bowel preparation in diabetic patients.

  15. Areas of Triangles

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    <正>We know that the area of any right triangle is half the area of the rectangle which has the same height and the same base with the triangle.The area of rectangle DFEG below is bh.So the area of triangle DFG is 1/2bh. Now we can give a proof of the conclusion that every triangle has half the area of a related rectangle.

  16. Psychological preparation in sport shooting

    OpenAIRE

    Ledecká, Kateřina

    2013-01-01

    Title: Psychological preparation in sport shooting Objectives: The objective of this thesis is usage of psychological preparation by sport shooting representation team in Czech Republic. How they are informed about psychological preparation. What it means to them. Which types of regulation they use and how they behave before and after a competition. Methods: A Questionnaire was used as a method for data obtaining. The questionnaire was compiled for the purposes of this Thesis. The researched ...

  17. Preoperative preparation of children

    Directory of Open Access Journals (Sweden)

    Priya Reshma Aranha

    2017-01-01

    Full Text Available Surgery is a stressful and anxiety provoking experience for children. Millions of children undergo surgery every year. The majority of children experience significant preoperative anxiety which intern can affect their recovery. Preoperative anxiety may bring about physical and physiological changes in children, which can be particularly evident in terms of increased heart rate and blood pressure. To identify various strategies used to minimize the preoperative anxiety of children and update their clinical effectiveness among children undergoing surgery, the authors searched PubMed, MEDLINE, CINAHL, ScienceDirect, Google Scholar, Scopus, and Cochrane Library for identifying the relevant studies and retrieved available literature. It is concluded that utilization of the strategies available to reduce the preoperative anxiety of children will be a promising intervention to reduce anxiety, to promote relaxation, satisfaction, and speedy recovery. Many of these techniques are simple, cost-effective and can be easily carried out by nurses. It is essential to use the age appropriate and individualized methods in preparing children for surgery. Further research is required to strengthen the evidence.

  18. Preparation for retirement seminar

    CERN Multimedia

    HR Department

    2010-01-01

    (Health insurance and wealth and succession planning) During the preparation for retirement seminar in November 2009, the sessions on health insurance in Switzerland and in France unfortunately had to be postponed. Participants in the seminar also expressed interest in an information session on “How to manage your wealth and organize your succession”. The sessions on health insurance will be held on 16 March 2010 and those on managing wealth and succession on 18 March 2010. Programme for Tuesday 16 March 2010 (TH Theory Conference Room, Building 4/3-006): 09:00 Health insurance in Switzerland by Mr. Sandro Breitenstein, Service de l'Assurance Maladie du Canton de Genève 10:00 Coffee break 10:20 Health insurance in France by Mr. Dominique Curtiaud, Caisse Primaire d'Assurance Maladie de l'Ain Programme for Thursday 18 March 2010 (TH Theory Conference Room, Building 4/3-006): 09:00 How to manage your wealth and organize your succession in Switzerland by Mr. Jean-Marc W...

  19. Preparing for the future

    CERN Multimedia

    Panos Charitos

    2016-01-01

    The second annual meeting of the Future Circular Collider (FCC) design study took place from 11 to 15 April in Rome.   The participants in the second annual meeting of the FCC design study. (Photo: Vinicio Tullio/INFN) More than 450 scientists, researchers and leaders of high-tech industry gathered in Rome to review the progress of the Future Circular Collider (FCC) design study. The study was kicked off in 2014 as a response to a statement in the European Strategy for Particle Physics, and today embraces 74 institutes from 26 countries. With the LHC programme well under way, particle physicists are at an exciting juncture. New results from the 13 TeV run could show that we are on the threshold of an eye-opening era that presents new challenges and calls for developments. “To prepare for its future, CERN should continue to develop a vibrant R&D programme that should take advantage of its strengths and uniqueness, pursue design studies for...

  20. Deterministic joint remote state preparation

    Energy Technology Data Exchange (ETDEWEB)

    An, Nguyen Ba, E-mail: nban@iop.vast.ac.vn [Center for Theoretical Physics, Institute of Physics, 10 Dao Tan, Ba Dinh, Hanoi (Viet Nam); Bich, Cao Thi [Center for Theoretical Physics, Institute of Physics, 10 Dao Tan, Ba Dinh, Hanoi (Viet Nam); Physics Department, University of Education No. 1, 136 Xuan Thuy, Cau Giay, Hanoi (Viet Nam); Don, Nung Van [Center for Theoretical Physics, Institute of Physics, 10 Dao Tan, Ba Dinh, Hanoi (Viet Nam); Physics Department, Hanoi National University, 334 Nguyen Trai, Thanh Xuan, Hanoi (Viet Nam)

    2011-09-26

    We put forward a new nontrivial three-step strategy to execute joint remote state preparation via Einstein-Podolsky-Rosen pairs deterministically. At variance with all existing protocols, in ours the receiver contributes actively in both preparation and reconstruction steps, although he knows nothing about the quantum state to be prepared. -- Highlights: → Deterministic joint remote state preparation via EPR pairs is proposed. → Both general single- and two-qubit states are studied. → Differently from all existing protocols, in ours the receiver participates actively. → This is for the first time such a strategy is adopted.

  1. Activation of cortical areas in music execution and imagining: a high-resolution EEG study.

    Science.gov (United States)

    Kristeva, Rumyana; Chakarov, Vihren; Schulte-Mönting, Jürgen; Spreer, Joachim

    2003-11-01

    Neuroimaging studies have shown that execution of a musical sequence on an instrument activates bilateral frontal opercular regions, in addition to bilateral sensorimotor and supplementary motor areas. During imagining activation of the same areas without primary sensorimotor areas was shown. We recorded EEG from 58 scalp positions to investigate the temporal sequence and the time course of activation of these areas while violin players prepared to execute, executed, prepared to imagine, or imagined a musical sequence on a violin. During the preparation for the sequence in three of seven musicians investigated the bilateral frontal opercular regions became active earlier than the motor areas and in one of them simultaneously with the motor areas. In two of the musicians a rather variable pattern of activation was observed. The frontal opercular regions were also strongly involved throughout the period of music execution or imagining. The supplementary motor area was involved in both preparation for the sequence and during execution and imagining of the sequence. The left primary sensorimotor area was involved in the preparation and termination of the musical sequence for both execution and imagining. The right sensorimotor area was strongly involved in the preparation for and during the execution of the sequence. We conclude that the bilateral frontal opercular regions are crucial in both preparation for and during music execution and imagining. They may have "mirror neurone" properties that underlie observation or imagining of one's own performance. The motor areas are differentially activated during the preparation and execution or imagining the sequence.

  2. Cavity preparation machine for the standardization of in vitro preparations

    Directory of Open Access Journals (Sweden)

    Carlos José Soares

    2008-09-01

    Full Text Available Several in vitro studies employ the confection of cavity preparations that are difficult to standardize by means of manual high speed handpieces. This study presents the development of a cavity preparation machine designed to standardize in vitro cavity preparations. A metal base of 25 mm x 25 mm x 4 mm (length x width x height was coupled to a small mobile table which was designed to be able to move by means of two precision micrometers (0.01-mm accuracy in the horizontal directions (right-left, and back-front. A high speed handpiece was coupled to a metallic connecting rod which had an accurate dial indicator enabling control of the vertical movement. The high speed handpiece is also able to move 180° around its longitudinal axis and 360° around its transversal axis. The suggested cavity preparation machine precisely helps in the standardization of cavity preparations for in vitro studies.

  3. Cavity preparation machine for the standardization of in vitro preparations.

    Science.gov (United States)

    Soares, Carlos José; Fonseca, Rodrigo Borges; Gomide, Henner Alberto; Correr-Sobrinho, Lourenço

    2008-01-01

    Several in vitro studies employ the confection of cavity preparations that are difficult to standardize by means of manual high speed handpieces. This study presents the development of a cavity preparation machine designed to standardize in vitro cavity preparations. A metal base of 25 mm x 25 mm x 4 mm (length x width x height) was coupled to a small mobile table which was designed to be able to move by means of two precision micrometers (0.01-mm accuracy) in the horizontal directions (right-left, and back-front). A high speed handpiece was coupled to a metallic connecting rod which had an accurate dial indicator enabling control of the vertical movement. The high speed handpiece is also able to move 180 degrees around its longitudinal axis and 360 degrees around its transversal axis. The suggested cavity preparation machine precisely helps in the standardization of cavity preparations for in vitro studies.

  4. Preparation of porous lanthanum phosphate with templates

    Energy Technology Data Exchange (ETDEWEB)

    Onoda, Hiroaki, E-mail: onoda@kpu.ac.jp [Department of Informatics and Environmental Sciences, Faculty of Life and Environmental Sciences, Kyoto Prefectural University, 1-5, Shimogamo Nakaragi-cyo, Sakyo-ku, Kyoto 606-8522 (Japan); Ishima, Yuya [Department of Applied Chemistry, Faculty of Life Sciences, Ritsumeikan University, 1-1-1, Nojihigashi, Kusatsu, Shiga 525-8577 (Japan); Takenaka, Atsushi [Department of Materials Science, Yonago National College of Technology, 4448, Hikona-cho, Yonago, Tottori 683-8502 (Japan); Tanaka, Isao [Department of Materials Science and Engineering, Faculty of Engineering, Kyoto University, Yoshida-Honmachi, Sakyo-ku, Kyoto 606-8501 (Japan)

    2009-08-05

    Malonic acid, propionic acid, glycine, n-butylamine, and urea were added to the preparation of lanthanum phosphate from lanthanum nitrate and phosphoric acid solutions. All additives were taken into lanthanum phosphate particles. The additives that have a basic site were easy to contain in precipitates. The addition of templates improved the specific surface area of lanthanum phosphate. The amount of pore, with radius smaller than 4 nm, increased with the addition of templates. The remained additives had influence on the acidic properties of lanthanum phosphate.

  5. Enamel thickness after preparation of tooth for porcelain laminate.

    Directory of Open Access Journals (Sweden)

    Ayoub Pahlevan

    2014-08-01

    Full Text Available In this investigation the thickness of enamel in the gingival, middle, and incisal thirds of the labial surface of the anterior teeth were measured regarding preparation of the teeth for porcelain laminate veneers.Part one, 20 extracted intact human maxillary central and lateral incisors ten of each were selected. The teeth were imbedded in autopolimerize acrylic resin. Cross section was preformed through the midline of the incisal, middle and cervical one-third of the labial surface of the teeth. The samples were observed under reflected stereomicroscope and the thickness of enamel was recorded. Part II, the effect of different types of preparation on dentin exposure was evaluated. Thirty maxillary central incisor teeth were randomly divided into two groups: A: Knife-edge preparation. B: Chamfer preparation. All samples were embedded in autopolimerize acrylic resin using a silicon mold. The samples were cut through the midline of the teeth. The surface of the samples were polished and enamel and dentin were observed under the stereomicroscope.Data were analyzed by ANOVA-one way test. The results of this study showed that the least enamel thickness in the central incisor was 345 and in lateral incisor is 235 μ this thickness is related to the one-third labial cervical area. Maximum thickness in maxillary central and lateral incisors in the one-third labial incisal surface was 1260 μ and 1220μ, respectively. In the second part of the study, the tendency of dentinal exposure was shown with the chamfer preparation, but no dentinal exposure was found in the knife-edge preparation. The differences between groups were significant (p<0.05.The knowledge of enamel thickness in different part of labial surface is very important. The thickness of enamel in the gingival area does not permit a chamfer preparation. The knife edge preparation is preferable in gingival area.

  6. Coal preparation. Energy program report

    Energy Technology Data Exchange (ETDEWEB)

    Anastas, M.Y.

    1975-06-01

    This is one of several special reports prepared in conjunction with a broad state-of-the-art study on underground coal mining. This report is essentially a review of the current technology of coal preparation and future research needs in this field. (GRA)

  7. Preparing Students for Romantic Relationships

    Science.gov (United States)

    Weissbourd, Richard; Peterson, Amelia; Weinstein, Emily

    2014-01-01

    One of the most important aspects in our lives is learning how to have mutual, caring romantic relationships. Yet while schools and many other industries in this country devote tremendous attention and resources to preparing the young for work, they do remarkably little to prepare them for generous, self-respecting sex and love. Educators and…

  8. Recent advances in preparative electrophoresis

    Science.gov (United States)

    Mosher, Richard A.; Thormann, Wolfgang; Egen, Ned B.; Couasnon, Pascal; Sammons, David W.

    1987-01-01

    Various approaches for preparative electrophoresis, and three new instruments for preparative electrophoresis are discussed. Consideration is given to isoelectric focusing, isotachophoresis, and zone electrophoresis, three gel-based electrophoresis methods. The design, functions, and performance of the Elphor VaP 21 device of Hannig (1982), the shear-stabilized BIOSTREAM separator of Thompson (1983), and the recycling isoelectric focusing device are described.

  9. Teacher Preparation and Student Achievement

    Science.gov (United States)

    Boyd, Donald J.; Grossman, Pamela L.; Lankford, Hamilton; Loeb, Susanna; Wyckoff, James

    2009-01-01

    There are fierce debates over the best way to prepare teachers. Some argue that easing entry into teaching is necessary to attract strong candidates, whereas others argue that investing in high quality teacher preparation is the most promising approach. Most agree, however, that we lack a strong research basis for understanding how to prepare…

  10. A Simple Preparation of Hexadeuteriocholesterol

    DEFF Research Database (Denmark)

    Holm, Torkil; Crossland, Ingolf

    1996-01-01

    26,26,26,27,27,27 Hxadeuterio cholesterol has been prepared in 9 stages from pregnenolone and hexadeuterio acetone with an overall yield of 7 %.......26,26,26,27,27,27 Hxadeuterio cholesterol has been prepared in 9 stages from pregnenolone and hexadeuterio acetone with an overall yield of 7 %....

  11. Should Broca's area include Brodmann area 47?

    Science.gov (United States)

    Ardila, Alfredo; Bernal, Byron; Rosselli, Monica

    2017-02-01

    Understanding brain organization of speech production has been a principal goal of neuroscience. Historically, brain speech production has been associated with so-called Broca’s area (Brodmann area –BA- 44 and 45), however, modern neuroimaging developments suggest speech production is associated with networks rather than with areas. The purpose of this paper was to analyze the connectivity of BA47 ( pars orbitalis) in relation to language . A meta-analysis was conducted to assess the language network in which BA47 is involved. The Brainmap database was used. Twenty papers corresponding to 29 experimental conditions with a total of 373 subjects were included. Our results suggest that BA47 participates in a “frontal language production system” (or extended Broca’s system). The BA47  connectivity found is also concordant with a minor role in language semantics. BA47 plays a central role in the language production system.

  12. Hydrologic Areas of Concern

    Data.gov (United States)

    University of New Hampshire — A Hydrologic Area of Concern (HAC) is a land area surrounding a water source, which is intended to include the portion of the watershed in which land uses are likely...

  13. BOEM Wind Planning Areas

    Data.gov (United States)

    Bureau of Ocean Energy Management, Department of the Interior — This data set represents the most recent changes for the Wind Development Planning Areas in the Atlantic. Wind Planning Areas in this dataset represent up to six...

  14. VT ZIP Code Areas

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) A ZIP Code Tabulation Area (ZCTA) is a statistical geographic entity that approximates the delivery area for a U.S. Postal Service five-digit...

  15. Sunk Lake Natural Area

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — The Sunk Lake Natural Area Management Plan guides the long-range development of the Natural Area by identifying and integrating appropriate habitats, management...

  16. Infrastructure Area Simplification Plan

    CERN Document Server

    Field, L.

    2011-01-01

    The infrastructure area simplification plan was presented at the 3rd EMI All Hands Meeting in Padova. This plan only affects the information and accounting systems as the other areas are new in EMI and hence do not require simplification.

  17. LeaseAreas

    Data.gov (United States)

    Bureau of Ocean Energy Management, Department of the Interior — Federal outer Continental Shelf (OCS) Sand and Gravel Borrow Areas (Lease Areas) are polygons which are maintained by the Bureau of Ocean Energy Management (BOEM),...

  18. Vermont Designated Natural Areas

    Data.gov (United States)

    Vermont Center for Geographic Information — Under Natural Areas Law (10 Vermont Statutes Annotated, Chapter 83 § 2607) the FPR commissioner, with the approval of the governor, may designate and set aside areas...

  19. 75 FR 17913 - Maintenance and Vegetation Management Along Existing Western Area Power Administration...

    Science.gov (United States)

    2010-04-08

    ... Area Power Administration DEPARTMENT OF AGRICULTURE Forest Service Maintenance and Vegetation Management Along Existing Western Area Power Administration Transmission Line Rights of Way on National... Administration, DOE; Forest Service, USDA. ACTION: Notice of Intent to Prepare an Environmental Impact...

  20. Preparation of PFS coagulant by sectionalized reactor

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The oxidation rate of ferrous sulfate is investigated for the preparation of polyferric sulfate(PFS) coagulant.It is proved that this reaction is zero order with respect to Fe2 +,first order with respect to NO2 (g),and first order with respect to the interface area between gas phase and liquid phase.According to this mechanism,sectionalized reactor(SR) is used in place of traditional reactor(TR),and the liquid of reaction mixture is recycled by pump.As a result,not only the flow path of reaction liquid is prolonged,but also gas-liquid contact area enlarged,and the reaction distinctly accelerated,compared with traditional reactor.The effects of parameters including temperature,acidity and others on the reaction rate are also discussed.

  1. The Ethiopean Language Area.

    Science.gov (United States)

    Ferguson, Charles A.

    This paper constitutes the fifth chapter of the forthcoming volume "Language in Ethiopia." In an effort to better define the particular linguistic area, the author analyzes phonological and grammatical features that languages in the area have in common. A number of features have been identified as characteristic of the area, and this…

  2. Selected areas in cryptography

    CERN Document Server

    Oorschot, Paul

    1997-01-01

    Selected Areas in Cryptography brings together in one place important contributions and up-to-date research results in this fast moving area. Selected Areas in Cryptography serves as an excellent reference, providing insight into some of the most challenging research issues in the field.

  3. Graphic Communications--Preparatory Area. Book I--Typography and Modern Typesetting. Student Manual.

    Science.gov (United States)

    Hertz, Andrew

    Designed to develop in the student skills in all of the preparatory functions of the graphic communications industry, this student guide covers copy preparation, art preparation, typography, camera, stripping, production management, and forms design, preparation, and analysis. In addition to the skills areas, material is included on the history of…

  4. Graphic Communications--Preparatory Area. Book I--Typography and Modern Typesetting. Student Manual.

    Science.gov (United States)

    Hertz, Andrew

    Designed to develop in the student skills in all of the preparatory functions of the graphic communications industry, this student guide covers copy preparation, art preparation, typography, camera, stripping, production management, and forms design, preparation, and analysis. In addition to the skills areas, material is included on the history of…

  5. Improving educational preparation for transcultural health care.

    Science.gov (United States)

    Le Var, R M

    1998-10-01

    There is increasing evidence that the health care needs of people from black and ethnic minority groups in England are not being met. A growing number of initiatives are being undertaken to remedy the situation. Many of them are focused on health care delivery at local and national levels. However, unless the preparation of health care professionals in the area of multi-cultural health care is appropriate and effective, a great deal of corrective action will continue to have to be taken. Despite 1997 having been the European Year Against Racism, it is still necessary to consider what educational preparation should be like. The article draws on identified inadequacies in health care provision as well as examples of initiatives taken to improve care provision. The author identifies deficiencies in educational preparation and proposes a range of actions to be taken. The article is focused on nursing, midwifery and health visiting education in England, but is deemed to be relevant to all health care professionals not only in Europe but other continents, as they become increasingly international and multi-ethnic.

  6. Preparation of gasification feedstock from leafy biomass.

    Science.gov (United States)

    Shone, C M; Jothi, T J S

    2016-05-01

    Dried leaves are a potential source of energy although these are not commonly used beside to satisfy daily energy demands in rural areas. This paper aims at preparing a leafy biomass feedstock in the form of briquettes which can be directly used for combustion or to extract the combustible gas using a gasifier. Teak (Tectona grandis) and rubber (Hevea brasiliensis) leaves are considered for the present study. A binder-assisted briquetting technique with tapioca starch as binder is adopted. Properties of these leafy biomass briquettes such as moisture content, calorific value, compressive strength, and shatter index are determined. From the study, briquettes with biomass-to-binder ratio of 3:5 are found to be stable. Higher mass percentage of binder is considered for preparation of briquettes due to the fact that leafy biomasses do not adhere well on densification with lower binder content. Ultimate analysis test is conducted to analyze the gasification potential of the briquettes. Results show that the leafy biomass prepared from teak and rubber leaves has calorific values of 17.5 and 17.8 MJ/kg, respectively, which are comparable with those of existing biomass feedstock made of sawdust, rice husk, and rice straw.

  7. Preparation Calcium Oxide From Chicken Eggshells

    Directory of Open Access Journals (Sweden)

    Risfidian Mohadi

    2016-08-01

    Full Text Available The preparation of metal oxide CaO from chicken eggshell has been carried out by decomposition at various temperatures 600, 700, 800, 900, and 1000oC. The metal oxide CaO was characterized using XRD. Furthermore, The optimum temperature for preparation of CaO was determined based on the XRD pattern, then the characterization of CaO was extended using FT-IR spectrophotometer and BET analysis. The results show that the optimum temperature for preparation of CaO from chicken eggshell is 900oC with peak of 2Ө at 32.3o, 37.4o, 53.9o, 64.2o and 67.5o, respectively. The FT-IR spectrums show the unique vibration for Ca-O at 393 cm-1. The BET analysis show that CaO has surface area 68 m2/g with pore volume 1.65 cm3/g and pore size 6.6 nm which can be classified as mesoporous.

  8. PREPARATION OF A POLYMER ARTICLE FOR SELECTIVE METALLIZATION

    DEFF Research Database (Denmark)

    2008-01-01

    The present invention relates to the field of selective metallization, and in particular to preparing a polymer article for selective metallization by submerging the article in a first liquid, and while submergedirradiate the article by a laser beam the area of the article on which the metal...... is to be deposited. An activation step, prior to the selective metallization, comprises submerging the article in an activation liquid for depositing seedparticles in the selected area. The irradiation of the selected area is proportionate so as to cause a temporary meltingof the polymer in the surface...... of the selected area of the polymer article. The invention is advantageous in that the preparation may be performed with a relatively high scan rate across the polymer article, and in that a quite limited use of toxic chemicals....

  9. PREPARATION OF A POLYMER ARTICLE FOR SELECTIVE METALLIZATION

    DEFF Research Database (Denmark)

    2008-01-01

    The present invention relates to the field of selective metallization, and in particular to preparing a polymer article for selective metallization by submerging the article in a first liquid, and while submergedirradiate the article by a laser beam the area of the article on which the metal...... is to be deposited. An activation step, prior to the selective metallization, comprises submerging the article in an activation liquid for depositing seedparticles in the selected area. The irradiation of the selected area is proportionate so as to cause a temporary meltingof the polymer in the surface...... of the selected area of the polymer article. The invention is advantageous in that the preparation may be performed with a relatively high scan rate across the polymer article, and in that a quite limited use of toxic chemicals....

  10. Large area controlled assembly of transparent conductive networks

    Energy Technology Data Exchange (ETDEWEB)

    Ivanov, Ilia N.; Simpson, John T.

    2015-09-29

    A method of preparing a network comprises disposing a solution comprising particulate materials in a solvent onto a superhydrophobic surface comprising a plurality of superhydrophobic features and interfacial areas between the superhydrophobic features. The plurality of superhydrophobic features has a water contact angle of at least about 150.degree.. The method of preparing the network also comprises removing the solvent from the solution of the particulate materials, and forming a network of the particulate materials in the interfacial areas, the particulate materials receding to the interfacial areas as the solvent is removed.

  11. CY15 Livermore Computing Focus Areas

    Energy Technology Data Exchange (ETDEWEB)

    Connell, Tom M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Cupps, Kim C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); D' Hooge, Trent E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Fahey, Tim J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Fox, Dave M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Futral, Scott W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Gary, Mark R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Goldstone, Robin J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hamilton, Pam G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Heer, Todd M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Long, Jeff W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Mark, Rich J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Morrone, Chris J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Shoopman, Jerry D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Slavec, Joe A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Smith, David W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Springmeyer, Becky R [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Stearman, Marc D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Watson, Py C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-01-20

    The LC team undertook a survey of primary Center drivers for CY15. Identified key drivers included enhancing user experience and productivity, pre-exascale platform preparation, process improvement, data-centric computing paradigms and business expansion. The team organized critical supporting efforts into three cross-cutting focus areas; Improving Service Quality; Monitoring, Automation, Delegation and Center Efficiency; and Next Generation Compute and Data Environments In each area the team detailed high level challenges and identified discrete actions to address these issues during the calendar year. Identifying the Center’s primary drivers, issues, and plans is intended to serve as a lens focusing LC personnel, resources, and priorities throughout the year.

  12. Grasping preparation enhances orientation change detection.

    Directory of Open Access Journals (Sweden)

    Tjerk P Gutteling

    Full Text Available Preparing a goal directed movement often requires detailed analysis of our environment. When picking up an object, its orientation, size and relative distance are relevant parameters when preparing a successful grasp. It would therefore be beneficial if the motor system is able to influence early perception such that information processing needs for action control are met at the earliest possible stage. However, only a few studies reported (indirect evidence for action-induced visual perception improvements. We therefore aimed to provide direct evidence for a feature-specific perceptual modulation during the planning phase of a grasping action. Human subjects were instructed to either grasp or point to a bar while simultaneously performing an orientation discrimination task. The bar could slightly change its orientation during grasping preparation. By analyzing discrimination response probabilities, we found increased perceptual sensitivity to orientation changes when subjects were instructed to grasp the bar, rather than point to it. As a control experiment, the same experiment was repeated using bar luminance changes, a feature that is not relevant for either grasping or pointing. Here, no differences in visual sensitivity between grasping and pointing were found. The present results constitute first direct evidence for increased perceptual sensitivity to a visual feature that is relevant for a certain skeletomotor act during the movement preparation phase. We speculate that such action-induced perception improvements are controlled by neuronal feedback mechanisms from cortical motor planning areas to early visual cortex, similar to what was recently established for spatial perception improvements shortly before eye movements.

  13. Beer as colon lavage preparation

    Energy Technology Data Exchange (ETDEWEB)

    Kinnunen, J.; Linden, H.; Pietilae, J.; Juutilainen, T.

    1987-09-01

    Six patients received beer preparation prior to double contrast barium enema. The beer group scored slightly better (though not statistically significantly) both in the cleanliness and in the mucosal coating of the bowel than the control group with standard preparation. The fluid balance was unaltered. The patients in the beer group felt surprisingly well, likely due to the good fluid and energy balance provided by the beer. The beer preparation could be used in cases, when the patients are ready to intake beer and want to maintain a good nutritional status.

  14. Engaging Students in Career Planning and Preparation through Ementoring

    Science.gov (United States)

    Kinkel, Doreen H.

    2011-01-01

    Following a developmental model of career planning and preparation, an ementoring program was devised for first semester freshmen to (1) heighten career awareness and stimulate career exploration in food and agricultural sciences; (2) expand interest and willingness to follow career opportunities beyond the regional geographic area; and (3)…

  15. Preparing Preservice Teachers to Address Bullying through Cartoon Lessons

    Science.gov (United States)

    Rule, Audrey C.; Logan, Stephanie R.; Kohler, Frank W.

    2013-01-01

    Students who qualify for special education services are at risk for being bullied because of their cognitive, emotional, behavioral, or physical differences. Currently, teachers are not effective enough in reducing bullying; better preservice teacher preparation in this area may help to alleviate the problem. The current study explored the effects…

  16. 7 CFR 1781.17 - Docket preparation and processing.

    Science.gov (United States)

    2010-01-01

    ..., DEPARTMENT OF AGRICULTURE (CONTINUED) RESOURCE CONSERVATION AND DEVELOPMENT (RCD) LOANS AND WATERSHED (WS..., WS advances and RCD loans will be prepared in accordance with the applicable provisions of part 1780... preliminary draft of the watershed plan or RCD area plan, together with an estimate of costs and benefits...

  17. 50 CFR 600.758 - Preparation of report.

    Science.gov (United States)

    2010-10-01

    ... Preparation of report. (a) At the conclusion of the negotiations, an FNP may submit a report. Such report shall specify: (1) All the areas where consensus was reached by the FNP, including, if appropriate, proposed conservation and management measures. (2) Any other information submitted by members of the...

  18. [Blood donation in urban areas].

    Science.gov (United States)

    Charpentier, F

    2013-05-01

    Medical and technical developments increase the difficulty to provide sufficient safe blood for all patients in developed countries and their sociodemographic and societal changes. Sufficient national blood supply remains a reached, however still actual, challenge. Tomorrow is prepared today: the management of blood donation programs both in line with these developments and with social marketing strategies is one of the keys to success. If the main components of this organization are well known (mobile blood drives in various appropriate environments, and permanent blood donation centers) their proportions in the whole process must evolve and their contents require adaptations, especially for whole blood donation in urban areas. We have to focus on the people's way of life changes related to increasing urbanization of the society and prominent position taken by very large cities. This requires targeting several goals: to draw the attention of the potential blood-giving candidate, to get into position to collect him when he will decide it, to give meaning and recognition to his "sacrifice" (give time rather than donate blood) and to give him desire and opportunity to come back and donate one more time. In this strategy, permanent blood centers in urban areas have significant potential for whole blood collection, highlighted by the decrease of apheresis technology requirements. This potential requires profound changes in their location, conception and organization. The concept of Maison Du Don (MDD) reflects these changes.

  19. Adolescent test or procedure preparation

    Science.gov (United States)

    ... imagery Trying other distractions, such as listening to music through headphones, if allowed When possible, let your ... MA, Chorney JM, Mayes L. Web-based tailored intervention for preparation of parents and children for outpatient ...

  20. Preparation of large monodisperse vesicles.

    Directory of Open Access Journals (Sweden)

    Ting F Zhu

    Full Text Available Preparation of monodisperse vesicles is important both for research purposes and for practical applications. While the extrusion of vesicles through small pores (approximately 100 nm in diameter results in relatively uniform populations of vesicles, extrusion to larger sizes results in very heterogeneous populations of vesicles. Here we report a simple method for preparing large monodisperse multilamellar vesicles through a combination of extrusion and large-pore dialysis. For example, extrusion of polydisperse vesicles through 5-microm-diameter pores eliminates vesicles larger than 5 microm in diameter. Dialysis of extruded vesicles against 3-microm-pore-size polycarbonate membranes eliminates vesicles smaller than 3 microm in diameter, leaving behind a population of monodisperse vesicles with a mean diameter of approximately 4 microm. The simplicity of this method makes it an effective tool for laboratory vesicle preparation with potential applications in preparing large monodisperse liposomes for drug delivery.

  1. Preparing for Assisted Reproductive Technology

    Science.gov (United States)

    ... CDC Cancel Submit Search The CDC Assisted Reproductive Technology (ART) Note: Javascript is disabled or is not ... visit this page: About CDC.gov . Assisted Reproductive Technology (ART) What Is ART Patient Resources Preparing for ...

  2. Preparing for Breast Reconstruction Surgery

    Science.gov (United States)

    ... Cancer Breast Reconstruction Surgery Preparing for Breast Reconstruction Surgery Your surgeon can help you know what to ... The plan for follow-up Costs Understanding your surgery costs Health insurance policies often cover most or ...

  3. CVP Service Area

    Data.gov (United States)

    California Department of Resources — Federal Water Contract Service Area boundaries are incorporated boundaries of districts having contracts with the U.S. Bureau of Reclamation (Reclamation), within...

  4. Aperture area measurement facility

    Data.gov (United States)

    Federal Laboratory Consortium — NIST has established an absolute aperture area measurement facility for circular and near-circular apertures use in radiometric instruments. The facility consists of...

  5. Fishing Access Areas

    Data.gov (United States)

    Vermont Center for Geographic Information — The Vermont Fish & Wildlife Department maintains developed fishing access areas. These sites provide public access to waters in Vermont for shore fishing...

  6. Northwest Area Science

    Science.gov (United States)

    Fuentes, Tracy L.; van Heeswijk, Marijke; Grossman, Eric E.

    2010-01-01

    Northwest Area Facts * Population about 12 million * 43 federally recognized Tribes * Hydropower provides about two-thirds of electricity supply * 78 federally listed threatened and endangered species * 12 active or potentially active volcanoes * Columbia River system drains more than 260,000 square miles, an area about the size of Texas * More than 175 square miles covered by glaciers * More than 900 miles of Pacific Ocean coastline * More than 2,300 miles of greater Puget Sound coastline * Some forests store more carbon per unit area than any other area in the world, including the tropics * 51 percent federal lands * Significant lead, zinc, silver, and phosphate deposits

  7. Preparing for Interaction : A comparative study on the different ways dutch actors prepare themself to work in the comprehensive approach

    NARCIS (Netherlands)

    Thönissen, F.H.; Homberg, M.J.C. van den; Pieneman, R.B.J.; Rjetjens, B.; Berg, P. van den

    2014-01-01

    This study provides an overview on how Dutch military and civilian professionals prepare themselves for a comprehensive approach in conflict-affected areas. What works for the different actors and what can be improved? The study addresses these and other questions.

  8. Preparation, characterization, and dye removal study of activated carbon prepared from palm kernel shell.

    Science.gov (United States)

    García, Juan Rafael; Sedran, Ulises; Zaini, Muhammad Abbas Ahmad; Zakaria, Zainul Akmar

    2017-04-08

    Palm oil mill wastes (palm kernel shell (PKS)) were used to prepare activated carbons, which were tested in the removal of colorants from water. The adsorbents were prepared by 1-h impregnation of PKS with ZnCl2 as the activating agent (PKS:ZnCl2 mass ratios of 1:1 and 2:1), followed by carbonization in autogenous atmosphere at 500 and 550 °C during 1 h. The characterization of the activated carbons included textural properties (porosity), surface chemistry (functional groups), and surface morphology. The dye removal performance of the different activated carbons was investigated by means of the uptake of methylene blue (MB) in solutions with various initial concentrations (25-400 mg/L of MB) at 30 °C, using a 0.05-g carbon/50-mL solution relationship. The sample prepared with 1:1 PKS:ZnCl2 and carbonized at 550 °C showed the highest MB adsorption capacity (maximum uptake at the equilibrium, q max = 225.3 mg MB / g adsorbent), resulting from its elevated specific surface area (BET, 1058 m(2)/g) and microporosity (micropore surface area, 721 m(2)/g). The kinetic experiments showed that removals over 90% of the equilibrium adsorptions were achieved after 4-h contact time in all the cases. The study showed that palm oil mill waste biomass could be used in the preparation of adsorbents efficient in the removal of colorants in wastewaters.

  9. Operational Area Environmental Evaluations

    Energy Technology Data Exchange (ETDEWEB)

    Bailey-White, Brenda Eileen [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Nagy, Michael David [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Wagner, Katrina Marie [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Goodman, Thomas Richard [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Herring, Allen [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Catechis, Christopher S. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Kinghorn, Aubrianna Nicole [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Johnson, Ellie [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Barthel, Michael David [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Casaus, Benito [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-08-01

    The Operational Area Environmental Evaluation update provides a description of activities that have the potential to adversely affect natural and cultural resources, including soil, air, water, biological, ecological, and historical resources. The environmental sensitivity of an area is evaluated and summarized, which may facilitate informed management decisions as to where development may be prohibited, restricted, or subject to additional requirements.

  10. Available area isotherm

    NARCIS (Netherlands)

    Bosma, JC; Wesselingh, JA

    2004-01-01

    A new isotherm is presented for adsorption of proteins, the available area isotherm. This isotherm has a steric basis, unlike the (steric) mass action model. The shape of the available area isotherm is determined only by geometric exclusion. With the new isotherm, experimental results can be fitted

  11. PYRAMID ROADLESS AREA, CALIFORNIA.

    Science.gov (United States)

    Armstrong, Augustus K.; Scott, Douglas F.

    1984-01-01

    A geologic and mineral survey was conducted in the Pyramid Roadless Area, California. The area contains mineral showings, but no mineral-resource potential was identified during our studies. Three granodiorite samples on the west side of the roadless area contained weakly anomalous concentrations of uranium. Two samples of roof-pendant rocks, one metasedimentary rock and one metavolcanic rock, contain low concentrations of copper, and of copper and molybdenum, respectively. Although none was identified, the geologic terrane is permissive for mineral occurrences and large-scale, detailed geologic mapping of the areas of metasedimentary and metavolcanic roof pendants in the Pyramid Roadless Area could define a mineral-resource potential for tungsten and precious metals.

  12. Synthesis and Characterization of Large Surface Area Yttrium Oxide by Precipitation Method

    Institute of Scientific and Technical Information of China (English)

    崔大立; 龙志奇; 张顺利; 崔梅生; 黄小卫

    2004-01-01

    The method for preparing yttrium oxide with large specific surface area was introduced. By means of BET, SEM, TG and DTA analysis, the effects of precipitant, stirring velocity, non-RE impurity in solution, calcination temperature, on the surface area were studied respectively. The Y2O3 sample with specific surface area of more than 60 m2*g-1 and L.O.I less than 1% was prepared in the suitable precipitation condition and calcinations temperature when the ammonia used as precipitant. The SEM shows that the Y2O3 prepared with large surface area is the aggregation of about 50 nm particles.

  13. Searching for ``Preparation for Future Learning'' in Physics

    Science.gov (United States)

    Etkina, Eugenia; Gentile, Michael; Karelina, Anna; Ruibal-Villasenor, Maria R.; Suran, Gregory

    2009-11-01

    "Preparation for future learning" is a term describing a new approach to transfer. In addition to focusing on learning environments that help students better apply developed knowledge in new situations; education researchers are searching for educational interventions that better prepare students to learn new information. The pioneering studies in this field were conducted by J. Branford and D. Schwartz in psychology and mathematics, specifically in the area of statistics. They found that students who engaged in innovation before being exposed to new material, learned better. We attempted to replicate their experiments in the field of physics, specifically in the area of conductivity. Using two experimental conditions and one control, we compared student learning of thermal and electrical conductivity from a written text. We present the results of groups' performance on seven qualitative questions after their learning in this area.

  14. Improvement in SOFC anode performance by finely-structured Ni/YSZ cermet prepared via heterocoagulation.

    Science.gov (United States)

    Sunagawa, Yoji; Yamamoto, Katsutoshi; Muramatsu, Atsushi

    2006-03-30

    A novel preparation technique for a nanostructured anode for a solid oxide fuel cell is investigated. By mixing nanometer-sized NiO and YSZ powders in a pH-controlled aqueous media, a fine mixture of nanoparticles is successfully obtained through heterocoagulation. The anode prepared from thus prepared mixture has a large triple phase boundary and shows a great improvement in the anode performance by increasing the electric conductivity and effective surface area.

  15. Promising Practices in the Preparation of Special Educators to Provide Reading Instruction

    Science.gov (United States)

    Sayeski, Kristin L.; Gormley Budin, Shannon E.; Bennett, Katie

    2015-01-01

    The majority of students with disabilities require support in the area of reading. Given the importance of reading instruction, it is essential that special education teacher preparation programs prepare candidates who are knowledgeable about reading development and skilled in the delivery of reading instruction. The purpose of this article is…

  16. Massive preparation of pitch-based organic microporous polymers for gas storage.

    Science.gov (United States)

    Li, Wenqing; Zhang, Aijuan; Gao, Hui; Chen, Mingjie; Liu, Anhua; Bai, Hua; Li, Lei

    2016-02-14

    A general challenge for preparing organic microporous polymers (MOPs) is to use cheap and sustainable building blocks while retaining the advanced functions. We demonstrate a strategy to massively prepare pitch-based MOPs, which are thermally and chemically stable. A maximum BET surface area of 758 m(2) g(-1) and high gas storage capacity were achieved.

  17. Protected areas and poverty

    Science.gov (United States)

    Brockington, Daniel; Wilkie, David

    2015-01-01

    Protected areas are controversial because they are so important for conservation and because they distribute fortune and misfortune unevenly. The nature of that distribution, as well as the terrain of protected areas themselves, have been vigorously contested. In particular, the relationship between protected areas and poverty is a long-running debate in academic and policy circles. We review the origins of this debate and chart its key moments. We then outline the continuing flashpoints and ways in which further evaluation studies could improve the evidence base for policy-making and conservation practice. PMID:26460124

  18. Preparation and characterization of rice husk/ferrite composites

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    A novel ferrite composite using rice husk as substrate has been prepared via high temperature treatment under nitrogen atmosphere.The rice husk substrate consists of porous activated carbon and silica,where spinel ferrite particles with average diameter of 59 nm are distributed.The surface area of the composite is greater than 170 m~2 g~(-1) and the bulk density is less than 0.6 g cm~(-3).Inert atmosphere is indispensable for the synthesis of pure ferrite composites,while different preparation temperatur...

  19. Artificial Metalloproteins Exploiting Vacant Space: Preparation, Structures, and Functions

    Science.gov (United States)

    Abe, Satoshi; Ueno, Takafumi; Watanabe, Yoshihito

    Molecular design of artificial metalloproteins is one of the most attractive subjects in bioinorganic chemistry. Protein vacant space has been utilized to prepare metalloproteins because it provides a unique chemical environment for application to catalysts and to biomaterials bearing electronic, magnetic, and medical properties. Recently, X-ray crystal structural analysis has increased in this research area because it is a powerful tool for understanding the interactions of metal complexes and protein scaffolds, and for providing rational design of these composites. This chapter reviews the recent studies on the preparation methods and X-ray crystal structural analyses of metal/protein composites, and their functions as catalysts, metal-drugs, etc.

  20. Remote preparation of quantum states

    CERN Document Server

    Bennett, C H; Leung, D W; Shor, P W; Winter, A; Bennett, Charles H; Hayden, Patrick; Leung, Debbie W.; Shor, Peter W.; Winter, Andreas

    2003-01-01

    Remote state preparation is the variant of quantum state teleportation in which the sender knows the quantum state to be communicated. The original paper introducing teleportation established minimal requirements for classical communication and entanglement but the corresponding limits for remote state preparation have remained unknown until now: previous work has shown, however, that it not only requires less classical communication but also gives rise to a trade-off between these two resources in the appropriate setting. We discuss this problem from first principles, including the various choices one may follow in the definitions of the actual resources. Our main result is a general method of remote state preparation for arbitrary states of many qubits, at a cost of 1 bit of classical communication and 1 bit of entanglement per qubit sent. In this "universal" formulation, these ebit and cbit requirements are shown to be simultaneously optimal by exhibiting a dichotomy. This then yields the exact trade-off c...

  1. Preparing for retirement - new seminars

    CERN Multimedia

    Human Resources Department

    2015-01-01

    We would like to take the opportunity to inform you about a new programme related to retirement, organised by the Human Resources Department. Retirement marks the end of a career and the start of a new chapter in life.  In all cases, being well-informed and prepared is necessary to cope successfully with this transition. The programme has been developed for staff members and consists of two seminars: Leaving CERN (half day seminar): short presentations by internal speakers, focusing on what options CERN offers at the end of your career: organised once per year, next session scheduled on 24 November 2015, in the afternoon, enrolment and more information on Indico.   Preparation for retirement (2-day seminar): interactive workshop (in small groups) delivered by external experts, focusing on how to prepare psychologically as well as practically to cope with all the changes retirement brings: organised regularly in 2016, in English or ...

  2. Preparation of semisynthetic (+)-tubocurarine chloride.

    Science.gov (United States)

    Naghaway, J; Soine, T O

    1979-05-01

    Semisynthetic (+)-tubocurarine chloride (II) was prepared by monoquaternization of (+)-tubocurine. The method involved treating (+)-tubocurine with a 0.5 M equivalent of hydrochloric acid prior to quaternization with methyl iodide, followed by neutralization and iodide-chloride ion-exchange. Column chromatography and crystallization procedures were utilized for pure semisynthetic II preparation. The neuromuscular junction blocking activities of the semisynthetic and commercial II were determined by the in vivo cat hypoglossal nerve-tongue muscle preparation. No delectable differences among physical constants, spectral data, and neuromuscular junction blocking activities were noted between the commercial product and the semisynthetic II. This result substantiates the chemical and biological data for the well-accepted new formula for II. The unexplained M + n14 mass spectral peaks shown by the curare-type bases are characteristic of the molecular species rather than a result of contaminants.

  3. Ice Engineering Research Area

    Data.gov (United States)

    Federal Laboratory Consortium — Refrigerated Physical Modeling of Waterways in a Controlled EnvironmentThe Research Area in the Ice Engineering Facility at the Cold Regions Research and Engineering...

  4. Driftless Area NWR ROCSTAR

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — The Resources of Concern Selection Tool for Americas Refuges (ROCSTAR) was developed to assist national wildlife refuges, waterfowl production areas, wetland...

  5. Pilot Boarding Areas

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Pilot boarding areas are locations at sea where pilots familiar with local waters board incoming vessels to navigate their passage to a destination port. Pilotage is...

  6. Decontamination & decommissioning focus area

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-01

    In January 1994, the US Department of Energy Office of Environmental Management (DOE EM) formally introduced its new approach to managing DOE`s environmental research and technology development activities. The goal of the new approach is to conduct research and development in critical areas of interest to DOE, utilizing the best talent in the Department and in the national science community. To facilitate this solutions-oriented approach, the Office of Science and Technology (EM-50, formerly the Office of Technology Development) formed five Focus AReas to stimulate the required basic research, development, and demonstration efforts to seek new, innovative cleanup methods. In February 1995, EM-50 selected the DOE Morgantown Energy Technology Center (METC) to lead implementation of one of these Focus Areas: the Decontamination and Decommissioning (D & D) Focus Area.

  7. SO2 Nonattainment Areas

    Data.gov (United States)

    U.S. Environmental Protection Agency — This data layer identifies areas in the U.S. where air pollution levels have not met the National Ambient Air Quality Standards (NAAQS) for Sulfur dioxide and have...

  8. PM 10 Nonattainment Areas

    Data.gov (United States)

    U.S. Environmental Protection Agency — This data layer identifies areas in the U.S. where air pollution levels have not met the National Ambient Air Quality Standards (NAAQS) for PM 10 and have been...

  9. Carbon Monoxide Nonattainment Areas

    Data.gov (United States)

    U.S. Environmental Protection Agency — This data layer identifies areas in the U.S. where air pollution levels have not met the National Ambient Air Quality Standards (NAAQS) for Carbon Monoxide and have...

  10. Weierstrass preparation and algebraic invariants

    CERN Document Server

    Harbater, David; Krashen, Daniel

    2011-01-01

    We prove a form of the Weierstrass Preparation Theorem for normal algebraic curves over complete discrete valuation rings. While the more traditional algebraic form of Weierstrass Preparation applies just to the projective line over a base, our version allows more general curves. This result is then used to obtain applications concerning the values of u-invariants, and on the period-index problem for division algebras, over fraction fields of complete two-dimensional rings. Our approach uses patching methods and matrix factorization results that can be viewed as analogs of Cartan's Lemma.

  11. EFFECTIVE PROCEDURES FOR EXECUTIVE'S PREPARATION

    Directory of Open Access Journals (Sweden)

    Elisabet Martínez Mondéjar

    2014-05-01

    The aim of this article is to present methodological procedure that facilitates the executives  work with teachers that are preparing themselves to by promoting post from their  workplace from  a manual directed towards counseling executives  on how to develop the focalization, the selection and the evaluation and promotion of its teachers that are preparing themselves to by promoting post  from the work system itself  of the different levels of management from the University of Pedagogical Sciences " Felix Varela Morales " of Villa Clara.

  12. Preparation of Hydrogenated Nitrile Rubber

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    @@ Hydrogenated nitrile rubber is an oil and solvent resistant rubber and particularly give more resistant to heat, ozone, light. It is generally prepared from nitrile rubber by selective hydrogenation using a suitable catalyst system. In the present work a prepared method was adapted for the hydrogenation reaction of nitrile rubber using homogeneous tris(tri-phenlphosphine)chlorhodium(I) catalyst (RhCl(PPh3)) system. The hydrogenation reaction was carriedout at different temperature, pressure, time and catalyst concentration, the concentration, the conditions of hydrogenation are stated in table 1.

  13. Preparation of Hydrogenated Nitrile Rubber

    Institute of Scientific and Technical Information of China (English)

    LIU; ZhiCai

    2001-01-01

    Hydrogenated nitrile rubber is an oil and solvent resistant rubber and particularly give more resistant to heat, ozone, light. It is generally prepared from nitrile rubber by selective hydrogenation using a suitable catalyst system. In the present work a prepared method was adapted for the hydrogenation reaction of nitrile rubber using homogeneous tris(tri-phenlphosphine)chlorhodium(I) catalyst (RhCl(PPh3)) system.  The hydrogenation reaction was carriedout at different temperature, pressure, time and catalyst concentration, the concentration, the conditions of hydrogenation are stated in table 1.  ……

  14. Preparation and Characterization of Graphene

    Directory of Open Access Journals (Sweden)

    Xu Man

    2015-01-01

    Full Text Available The homogeneous-dispersed graphene oxide was prepared by the improved Hummers method, which would be reduced to graphene with the reducing agent called hydrazine hydrate. The X-ray diffraction, Infrared spectroscopy, Raman spectra and Transmission electron microscopy were used to analysis the phase, morphology and structure of the graphene and graphene oxide. The results show that the graphene oxide and reduced graphene oxide prepared via this method, whose degree of oxidation and reduction are high; Also obtained a higher well-disperses and less structural imperfection of the graphene that was manufactured in the reducing system that added ammonia reduction

  15. Preparation and characterization of mesoporous indium oxide

    Institute of Scientific and Technical Information of China (English)

    ZHAO Yi-zhe; CHENG Zhi-xuan; PAN Qing-yi; DONG Xiao-wen; ZHANG Jian-cheng; PAN Ling-li

    2009-01-01

    Indium oxide nanocrystals with mesoporous structure were successfully synthesized by using triblock copolymer as a template,and characterized by thermogravimetry-differential scanning calorimeter (TG-DSC),X-ray powder diffraction (XRD),high resolution transmission electron microscopy (HRTEM) and N2 adsorption.A high EO/PO ratio is thought to be the key point to prepare mesoporous In2O3.The results show that the average pore diameter of the products is 6 nm,the BET surface area is 54.78 m2/g,and the adsorbing pore volume is 0.345 cm3/g.After comparing with normal indium oxide nanoparticles by BET test,mesoporous indium oxide demonstrates a large difference in adsorbing pore volume and average pore diameters from normal ones.

  16. Preparation and Application of Fluorescent Carbon Dots

    Directory of Open Access Journals (Sweden)

    Jun Zuo

    2015-01-01

    Full Text Available Fluorescent carbon dots (CDs are a novel type of fluorescent nanomaterials, which not only possess the specific quantum confinement effects of nanomaterials due to the small size of nanomaterials, but also have good biocompatibility and high fluorescence. Meanwhile, fluorescence CDs overcome the shortcomings of high toxicity of traditional nanomaterials. Moreover, the preparation procedure of fluorescent CDs is simple and easy. Therefore, fluorescent CDs have great potential applied in photocatalysis, biochemical sensing, bioimaging, drug delivery, and other related areas. In this paper, recent hot researches on fluorescent CDs are reviewed and some problems in the progress of fluorescent CDs are also summarized. At last, a future outlook in this direction is presented.

  17. Generic hierarchical engine for mask data preparation

    Science.gov (United States)

    Kalus, Christian K.; Roessl, Wolfgang; Schnitker, Uwe; Simecek, Michal

    2002-07-01

    Electronic layouts are usually flattened on their path from the hierarchical source downstream to the wafer. Mask data preparation has certainly been identified as a severe bottleneck since long. Data volumes are not only doubling every year along the ITRS roadmap. With the advent of optical proximity correction and phase-shifting masks data volumes are escalating up to non-manageable heights. Hierarchical treatment is one of the most powerful means to keep memory and CPU consumption in reasonable ranges. Only recently, however, has this technique acquired more public attention. Mask data preparation is the most critical area calling for a sound infrastructure to reduce the handling problem. Gaining more and more attention though, are other applications such as large area simulation and manufacturing rule checking (MRC). They all would profit from a generic engine capable to efficiently treat hierarchical data. In this paper we will present a generic engine for hierarchical treatment which solves the major problem, steady transitions along cell borders. Several alternatives exist how to walk through the hierarchy tree. They have, to date, not been thoroughly investigated. One is a bottom-up attempt to treat cells starting with the most elementary cells. The other one is a top-down approach which lends itself to creating a new hierarchy tree. In addition, since the variety, degree of hierarchy and quality of layouts extends over a wide range a generic engine has to take intelligent decisions when exploding the hierarchy tree. Several applications will be shown, in particular how far the limits can be pushed with the current hierarchical engine.

  18. Plutonium focus area. Technology summary

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-09-01

    The Assistant Secretary for the Office of Environmental Management (EM) at the U.S. Department of Energy (DOE) chartered the Plutonium Focus Area (PFA) in October 1995. The PFA {open_quotes}...provides for peer and technical reviews of research and development in plutonium stabilization activities...{close_quotes} In addition, the PFA identifies and develops relevant research and technology. The purpose of this document is to focus attention on the requirements used to develop research and technology for stabilization, storage, and preparation for disposition of nuclear materials. The PFA Technology Summary presents the approach the PFA uses to identify, recommend, and review research. It lists research requirements, research being conducted, and gaps where research is needed. It also summarizes research performed by the PFA in the traditional research summary format. This document encourages researchers and commercial enterprises to do business with PFA by submitting research proposals or {open_quotes}white papers.{close_quotes} In addition, it suggests ways to increase the likelihood that PFA will recommend proposed research to the Nuclear Materials Stabilization Task Group (NMSTG) of DOE.

  19. 5 CFR 591.207 - Which areas are COLA areas?

    Science.gov (United States)

    2010-01-01

    ... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Which areas are COLA areas? 591.207... ALLOWANCES AND DIFFERENTIALS Cost-of-Living Allowance and Post Differential-Nonforeign Areas Cost-Of-Living Allowances § 591.207 Which areas are COLA areas? OPM has established the following COLA areas: (a) City...

  20. 5 CFR 591.205 - Which areas are nonforeign areas?

    Science.gov (United States)

    2010-01-01

    ... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Which areas are nonforeign areas? 591.205... ALLOWANCES AND DIFFERENTIALS Cost-of-Living Allowance and Post Differential-Nonforeign Areas Cost-Of-Living Allowances and Post Differentials § 591.205 Which areas are nonforeign areas? (a) The nonforeign areas...

  1. 200 Area Interim Storage Area Technical Safety Requirements

    Energy Technology Data Exchange (ETDEWEB)

    CARRELL, R.D.

    2000-03-15

    The 200 Area Interim Storage Area Technical Safety Requirements define administrative controls and design features required to ensure safe operation during receipt and storage of canisters containing spent nuclear fuel. This document is based on the 200 Area Interim Storage Area, Annex D, Final Safety Analysis Report which contains information specific to the 200 Area Interim Storage Area.

  2. Preparing Your Child for Surgery

    Science.gov (United States)

    ... Child What Kids Say About: Handling Stress Anxiety, Fears, and Phobias Community Service: A Family's Guide to Getting Involved Teaching Kids to Be Smart About Social Media Preparing Your Child for Surgery ... Questions Explain the Problem Handle Fears Relieve Guilt Explaining What Will Happen Pre-Operative ...

  3. Professional Preparation in Health Promotion.

    Science.gov (United States)

    Hill, Charles E.; Fisher, Shirley P.

    1992-01-01

    Colleges and universities must develop curricula to prepare health promotion specialists to work with persons of all ages. Program core should include self-care, consumer awareness, nutrition, weight control, stress management, and substance abuse. Health and physical educators should learn to facilitate change of negative health behaviors into…

  4. Preparing Foster Children for School

    Science.gov (United States)

    Antoine, Karla; Fisher, Philip A.

    2006-01-01

    Preparing foster children for school entry by focusing on the skills necessary to succeed in kindergarten calls for early intervention. However, existing programs to enhance school readiness have not been tailored to meet the educational, emotional, and psychological needs of foster children. This is the rationale behind development of the…

  5. Transforming Principal Preparation. ERIC Digest.

    Science.gov (United States)

    Lashway, Larry

    In the current climate of accountability, the responsibilities of principals have increased. The new role of principals requires new forms of training, and standards-based reform is generating major changes in principal-preparation programs. This digest examines some of those changes. First, it looks at the effectiveness of principal-preparation…

  6. Preparing Teachers for Parent Involvement.

    Science.gov (United States)

    Safran, Daniel

    This paper examines the potential impact of parent involvement in the formal education of their children and suggests ways that teacher education can be restructured to prepare teachers to work with parents. This paper attempts to answer five questions: (1) Why should parents be involved in the formal education of their children? (2) Why should…

  7. Attracting and Preparing Worthy Teachers.

    Science.gov (United States)

    Shiina, Mankichi; Chonan, Mitsuo

    1993-01-01

    Attracting worthy teachers to the compulsory education system in Japan requires attention to three issues: teacher salaries, strengthening initial teacher preparation, and expansion and systemization of teacher training. The one-year beginning teachers' inservice training program began in 1989 in response to the third issue. (IAH)

  8. Standards for Art Teacher Preparation.

    Science.gov (United States)

    Henry, Carole; Banks, Sam; Day, Michael; Dunn, Phil; Fergus, Victoria; Foster, Mary Sue; Galbraith, Lynn; Hatfield, Thomas A.; Hansen, Mark; Young, Bernard

    Colleges and universities engaged in the preparation of art teachers address a broad range of issues. Questions concerning specific education requirements leading to certification, approaches to curriculum development and assessment, opportunities for clinical experiences, and exposure to teaching methodologies and classroom management strategies…

  9. Preparation from Co-cities

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    @@ At the latest conference press held in mid of April, it is released by Chinese government officials that preparations for the Beijing Olympic Games in co-host cities are progressing well and most of the facilities are already in place.

  10. Standards for Art Teacher Preparation

    Science.gov (United States)

    National Art Education Association, 2009

    2009-01-01

    The National Art Education Association (NAEA) is committed to ensuring student access to a highly qualified, certified visual arts educator in every K-12 public school across the United States, recognizing that effective arts instruction is a core component to a 21st-century education. "Standards for Art Teacher Preparation" represents the…

  11. Preparing Student Mobility through Telecollaboration

    Science.gov (United States)

    Giralt, Marta; Jeanneau, Catherine

    2016-01-01

    In recent years, going to a foreign country has become all the more significant for Higher Education (HE) students, as concepts such as internationalisation and intercultural competencies have gained a more prominent role in HE. For students to fully benefit from this experience, it is paramount to prepare them for their stay in a foreign country…

  12. Preparing Engineers for Social Responsibility

    Science.gov (United States)

    Zandvoort, H.

    2008-01-01

    In this paper I introduce the contributions to a special section of the journal: one devoted to the question of how engineering curricula can or should contribute to the preparation of graduates for socially responsible decision making and conduct. The special section is motivated by the circumstance that, although there is broad agreement that…

  13. Preparing Students for Studying Abroad

    Science.gov (United States)

    Goldoni, Federica

    2015-01-01

    This study is situated in the fields of language education, study abroad (SA) and intercultural communication. The interest in SA is increasing on the part of students, administrators, educators, and business companies for the learning opportunities that it offers. However, SA students are not always prepared to maximize their learning…

  14. Preparing Slide Presentations on Computers.

    Science.gov (United States)

    Elberfeld, John K.

    1982-01-01

    Suggest use of well-organized slide presentation as effective way to introduce computers to large audiences and discusses how to get started--state objective, analyze audience, outline presentation, prepare slides--and equipment needed to obtain slides from television screens, miniature components, and book illustrations. References and sources…

  15. Preparation of a tritiated ginkgolide

    DEFF Research Database (Denmark)

    Strømgaard, Kristian; Suehiro, Makiko; Nakanishi, Koji

    2004-01-01

    Ginkgolide B, a constituent of the tree Ginkgo biloba, was radiolabeled with the beta-emitter tritium ([(3)H]) in two steps from ginkgolide C. First, a triflate precursor was prepared utilizing the selective reactivity of 7-OH in ginkgolide C; the triflate was then reduced with sodium borotritide...

  16. Preparation methods of alginate nanoparticles

    NARCIS (Netherlands)

    Paques, J.P.; Linden, van der E.; Rijn, van C.J.M.; Sagis, L.M.C.

    2014-01-01

    This article reviews available methods for the formation of alginate nano-aggregates, nanocapsules and nanospheres. Primarily, alginate nanoparticles are being prepared by two methods. In the “complexation method”, complex formation on the interface of an oil droplet is used to form alginate

  17. Preparation methods of alginate nanoparticles

    NARCIS (Netherlands)

    Paques, J.P.; Linden, van der E.; Rijn, van C.J.M.; Sagis, L.M.C.

    2014-01-01

    This article reviews available methods for the formation of alginate nano-aggregates, nanocapsules and nanospheres. Primarily, alginate nanoparticles are being prepared by two methods. In the “complexation method”, complex formation on the interface of an oil droplet is used to form alginate nanocap

  18. Handbook for Preparing Job Classifications.

    Science.gov (United States)

    Thomas, John C.

    To assist local governments in their responsibility for eliminating and preventing discrimination in employment based on race, color, religion, sex, or national origin as specified by the Equal Employment Opportunity Act of 1972, the handbook provides guidelines for analyzing jobs and preparing job classifications (defining; listing duties…

  19. Preparing Engineers for Social Responsibility

    Science.gov (United States)

    Zandvoort, H.

    2008-01-01

    In this paper I introduce the contributions to a special section of the journal: one devoted to the question of how engineering curricula can or should contribute to the preparation of graduates for socially responsible decision making and conduct. The special section is motivated by the circumstance that, although there is broad agreement that…

  20. Practicing Improvisation: Preparing Multicultural Educators

    Science.gov (United States)

    Hull, Karla

    2015-01-01

    Preparing competent multicultural educators involves a dynamic process requiring constant self-reflection and assisting pre-service teachers to sharpen their cultural vision as they learn to be responsive educators. Reflections on lessons learned as a teacher educator are shared through personal experiences that are identified as keys to prepare…

  1. Integrated Work Management: Preparer, Course 31883

    Energy Technology Data Exchange (ETDEWEB)

    Simpson, Lewis Edward [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-08-07

    The preparer (also called the “planner”) plays a key role in the integrated work management (IWM) process at Los Alamos National Laboratory (LANL). This course, Integrated Work Management: Preparer (COURSE 31883), describes the IWM roles and responsibilities of the preparer. This course also discusses IWM requirements that must be met by the preparer.

  2. 21 CFR 864.4400 - Enzyme preparations.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Enzyme preparations. 864.4400 Section 864.4400...) MEDICAL DEVICES HEMATOLOGY AND PATHOLOGY DEVICES Specimen Preparation Reagents § 864.4400 Enzyme preparations. (a) Identification. Enzyme preparations are products that are used in the...

  3. Preparation of high specific surface area magnetic ordered mesoporous carbons and adsorption property of methylene blue%高比表面磁性有序介孔炭的合成及对亚甲基蓝的吸附性能

    Institute of Scientific and Technical Information of China (English)

    田勇; 钟国英; 王秀芳; 林汉森

    2012-01-01

    Magnetic Fe-containing ordered mesoporous carbons (Fe/OMCs) with high surface area and large pore volume provide an easy and effective way for the treatment of dye in waste water. Fe/OMCs were synthesized by the soft-template route,wherein phenolic resin was used as a carbon precursor,triblock copolymer F127 as a template agent,tetraethylorsilicate (TEOS) as a silica precursor and hydrated iron nitrate as an iron source. The effects of Fe(NO3)3 · 9H2O loading on the morphology,structural parameters,and magnetic properties of the Fe/OMCs were evaluated by X-ray diffraction (XRD),N2 sorption analysis,transmission electron microscopy ( TEM) and physical property measurements. By using methylene blue (MB) as model dye,the adsorption of MB on the obtained Fe/ OMCs was investigated. The experimental results showed that the ordering,specific surface area and total pore volume decreased with the increase of Fe(NO3)3 · 9H2O loading. The Fe/OMCs had fast adsorption ability for MB. The adsorption of MB on the obtained Fe/OMCs followed the Sips adsorption equation and the corresponding parameters were obtained.%具有高比表面积、大孔容的铁磁性有序介孔炭(Fe/OMCs)对含染料废水的处理提供了一种简单有效的方法.采用苯酚树脂作炭源,三嵌段共聚物F127为模板剂,正硅酸乙酯为硅前驱体,硝酸铁为磁源,通过软模路线合成了Fe/OMCs.利用X射线衍射仪(XRD),氮气吸附仪,透射电镜(TEM)和综合物性测试仪研究了硝酸铁加入量对Fe/OMCs的相态、孔结构参数和磁性的影响;并以亚甲基蓝(MB)为染料探针分子,研究了Fe/OMCs对MB的吸附行为.结果表明材料有序性、比表面和孔容随着硝酸铁加入量的增加而降低,而饱和磁化强度明显增强.Fe/OMCs对MB有快速吸附能力,其行为符合Sips吸附方程.

  4. Environmental Resources of Selected Areas of Hawaii: Ecological Resources (DRAFT)

    Energy Technology Data Exchange (ETDEWEB)

    Trettin, C.C.; Tolbert, V.R.; Jones, A.T.; Smith, C.R.; Kalmijn, A.J.

    1994-06-01

    This report has been prepared to make available and archive the background scientific data and related information collected on ecological resources during the preparation of the environmental impact statement (EIS) for Phases 3 and 4 of the Hawaii Geothermal Project (HGP) as defined by the state of Hawaii in its April 1989 proposal to Congress. The U.S. Department of Energy (COE) published a notice in the Federal Register on May 17, 1994 (Fed. Regist. 5925638) withdrawing its Notice of Intent (Fed. Regst. 575433) of February 14, 1992, to prepare the HGP-EIS. Since the state of Hawaii is no longer pursuing or planning to pursue the HGP, DOE considers the project to be terminated. The background scientific data and related information presented in this report focus on several areas of Hawaii County, including the southeastern coast, a potential development corridor along the Saddle Road between Hilo and the North Kohala District on the northwestern coast, and on the southeastern coast of Maui. In this report, reference is made to these areas as study areas rather than as areas where proposed or alternative facilities of the HGP would be located. The resource areas addressed herein include terrestrial ecology, aquatic ecology, and marine ecology. The scientific background data and related information is being made available for future research in these areas. This report describes the environmental resources present in the areas studied (i.e., the affected environment) and does not represent an assessment of environmental impacts.

  5. Large area modules based on low band gap polymers

    DEFF Research Database (Denmark)

    Bundgaard, Eva; Krebs, Frederik C

    2010-01-01

    The use of three low band gap polymers in large area roll-to-roll coated modules is demonstrated. The polymers were prepared by a Stille cross coupling polymerization and all had a band gap around 1.6 eV. The polymers were first tested in small area organic photovoltaic devices which showed...... efficiencies from 0.4 to 2 %. Then large area roll-to-roll coated modules were processed and these showed efficiencies up to 0.6 %. It is clear that further study is necessary before this type of polymer is competitive with P3HT in large area modules....

  6. Preparation of spherical cobalt carbonate powder with high tap density

    Institute of Scientific and Technical Information of China (English)

    XIAO Jin; WANG Jian-feng; LIU Yong-dong; LI Jie; LIU Ye-xiang

    2006-01-01

    Spherical cobalt carbonate with high tap density, good crystallization and uniform particle size was prepared by controlled chemical crystal method using cobalt chloride and ammonium bicarbonate as cobalt source and precipitator. The effects of pH value and reaction time on crystallization and physical properties of cobalt carbonate were studied. The results show that the key factors influencing the preparation process of spherical cobalt carbonate with high tap density and good crystallization are how to control pH value (7.25 ± 0.05) and keep some reaction time (about 10 h). Co4O3 was prepared by sintering spherical morphology CoCO3 samples at varied temperatures. The results show that as the decomposition temperature increases, the as-obtained Co4O3 products with porous structure transform into polyhedral structure with glazed surface, and simultaneously the cobalt content and tap density increase. However, the specific surface area shows a trend of decrease.

  7. Large area LED package

    Science.gov (United States)

    Goullon, L.; Jordan, R.; Braun, T.; Bauer, J.; Becker, F.; Hutter, M.; Schneider-Ramelow, M.; Lang, K.-D.

    2015-03-01

    Solid state lighting using LED-dies is a rapidly growing market. LED-dies with the needed increasing luminous flux per chip area produce a lot of heat. Therefore an appropriate thermal management is required for general lighting with LEDdies. One way to avoid overheating and shorter lifetime is the use of many small LED-dies on a large area heat sink (down to 70 μm edge length), so that heat can spread into a large area while at the same time light also appears on a larger area. The handling with such small LED-dies is very difficult because they are too small to be picked with common equipment. Therefore a new concept called collective transfer bonding using a temporary carrier chip was developed. A further benefit of this new technology is the high precision assembly as well as the plane parallel assembly of the LED-dies which is necessary for wire bonding. It has been shown that hundred functional LED-dies were transferred and soldered at the same time. After the assembly a cost effective established PCB-technology was applied to produce a large-area light source consisting of many small LED-dies and electrically connected on a PCB-substrate. The top contacts of the LED-dies were realized by laminating an adhesive copper sheet followed by LDI structuring as known from PCB-via-technology. This assembly can be completed by adding converting and light forming optical elements. In summary two technologies based on standard SMD and PCB technology have been developed for panel level LED packaging up to 610x 457 mm2 area size.

  8. CHANCHELULLA ROADLESS AREA, CALIFORNIA.

    Science.gov (United States)

    Huber, Donald F.; Stebbins, Scott A.

    1984-01-01

    On the basis of a mineral survey there seems to be little likelihood for the occurrence of mineral resources in the Chanchelulla Roadless Area, California, except for a demonstrated resource of about 7200 tons containing 0. 084 oz gold/ton, 0. 84 oz silver/ton, and accessory copper at the Chanchelulla prospect. This prospect is located on a northwest-trending quartz vein. Limestone and small amounts of magnetite occur in the area but on the basis of available data no resources are identified. No potential for energy resources was identified.

  9. OLED area illumination source

    Science.gov (United States)

    Foust, Donald Franklin; Duggal, Anil Raj; Shiang, Joseph John; Nealon, William Francis; Bortscheller, Jacob Charles

    2008-03-25

    The present invention relates to an area illumination light source comprising a plurality of individual OLED panels. The individual OLED panels are configured in a physically modular fashion. Each OLED panel comprising a plurality of OLED devices. Each OLED panel comprises a first electrode and a second electrode such that the power being supplied to each individual OLED panel may be varied independently. A power supply unit capable of delivering varying levels of voltage simultaneously to the first and second electrodes of each of the individual OLED panels is also provided. The area illumination light source also comprises a mount within which the OLED panels are arrayed.

  10. SELKIRK ROADLESS AREA, IDAHO.

    Science.gov (United States)

    Miller, Fred K.; Benham, John R.

    1984-01-01

    On the basis of mineral-resource surveys the Selkirk Roadless Area, Idaho has little promise for the occurrence of mineral or energy resources. Molybdenum, lead, uranium, thorium, chromium, tungsten, zirconium, and several rare-earth elements have been detected in panned concentrates from samples of stream sediment, but no minerals containing the first five elements were found in place, nor were any conditions conducive to their concentration found. Zirconium, thorium, and the rare earths occur in sparsely disseminated accessory minerals in granitic rocks and no resource potential is identified. There is no history of mining in the roadless area and there are no oil, gas, mineral, or geothermal leases or current claims.

  11. Local Area Networks.

    Science.gov (United States)

    Marks, Kenneth E.; Nielsen, Steven

    1991-01-01

    Discusses cabling that is needed in local area networks (LANs). Types of cables that may be selected are described, including twisted pair, coaxial cables (or ethernet), and fiber optics; network topologies, the manner in which the cables are laid out, are considered; and cable installation issues are discussed. (LRW)

  12. Plutonium focus area

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-01

    To ensure research and development programs focus on the most pressing environmental restoration and waste management problems at the U.S. Department of Energy (DOE), the Assistant Secretary for the Office of Environmental Management (EM) established a working group in August 1993 to implement a new approach to research and technology development. As part of this new approach, EM developed a management structure and principles that led to the creation of specific Focus Areas. These organizations were designed to focus the scientific and technical talent throughout DOE and the national scientific community on the major environmental restoration and waste management problems facing DOE. The Focus Area approach provides the framework for intersite cooperation and leveraging of resources on common problems. After the original establishment of five major Focus Areas within the Office of Technology Development (EM-50, now called the Office of Science and Technology), the Nuclear Materials Stabilization Task Group (EM-66) followed the structure already in place in EM-50 and chartered the Plutonium Focus Area (PFA). The following information outlines the scope and mission of the EM, EM-60, and EM-66 organizations as related to the PFA organizational structure.

  13. Areas of Learning

    Science.gov (United States)

    Coe, John

    2010-01-01

    This article examines the recommendations made by the Independent Review of the Primary Curriculum (the Rose Report in 2009) that the curriculum should be organised into areas of learning. The implications for teachers are considered. By drawing upon past experience some major weaknesses and strengths implicit in the approach are identified and…

  14. Content Area Vocabulary Learning

    Science.gov (United States)

    Fisher, Douglas; Frey, Nancy

    2014-01-01

    Students' vocabulary knowledge is a significant predictor of their overall comprehension. The Common Core State Standards are raising the expectations for word learning and there are now 4 distinct standards related to vocabulary as well as expectations in other standards, including content areas. To address these expectations, teachers need…

  15. Protected areas in mountains

    Directory of Open Access Journals (Sweden)

    Hamilton, L. S.

    2006-12-01

    Full Text Available

    The importance of a global Protected Areas Network in sustaining appropriate mountain development is presented in this paper. Present status of the world’s “official” Protected Areas in the UN List, and the proportion that are in mountain areas, and including international designations (World Heritage and Biosphere Reserves. Current and future challenges in the management of these special areas are also commented.



    El autor destaca la importancia de una Red Mundial de Espacios Protegidos para el desarrollo sostenible de las montañas. Comenta luego el estatus actual de las Áreas Protegidas “oficiales” del Mundo en la Lista de las Naciones Unidas y qué proporción de ellas forma parte de las montañas, sin olvidar las figuras internacionales de protección como Patrimonio de la Humanidad y Reservas de Biosfera. Para terminar, se discuten los problemas de gestión actuales y futuros de estas áreas tan especiales

  16. Subsurface contaminants focus area

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-01

    The US Department of Enregy (DOE) Subsurface Contaminants Focus Area is developing technologies to address environmental problems associated with hazardous and radioactive contaminants in soil and groundwater that exist throughout the DOE complex, including radionuclides, heavy metals; and dense non-aqueous phase liquids (DNAPLs). More than 5,700 known DOE groundwater plumes have contaminated over 600 billion gallons of water and 200 million cubic meters of soil. Migration of these plumes threatens local and regional water sources, and in some cases has already adversely impacted off-site rsources. In addition, the Subsurface Contaminants Focus Area is responsible for supplying technologies for the remediation of numerous landfills at DOE facilities. These landfills are estimated to contain over 3 million cubic meters of radioactive and hazardous buried Technology developed within this specialty area will provide efective methods to contain contaminant plumes and new or alternative technologies for development of in situ technologies to minimize waste disposal costs and potential worker exposure by treating plumes in place. While addressing contaminant plumes emanating from DOE landfills, the Subsurface Contaminants Focus Area is also working to develop new or alternative technologies for the in situ stabilization, and nonintrusive characterization of these disposal sites.

  17. Hydrogel: Preparation, characterization, and applications: A review

    Directory of Open Access Journals (Sweden)

    Enas M. Ahmed

    2015-03-01

    Full Text Available Hydrogel products constitute a group of polymeric materials, the hydrophilic structure of which renders them capable of holding large amounts of water in their three-dimensional networks. Extensive employment of these products in a number of industrial and environmental areas of application is considered to be of prime importance. As expected, natural hydrogels were gradually replaced by synthetic types due to their higher water absorption capacity, long service life, and wide varieties of raw chemical resources. Literature on this subject was found to be expanding, especially in the scientific areas of research. However, a number of publications and technical reports dealing with hydrogel products from the engineering points of view were examined to overview technological aspects covering this growing multidisciplinary field of research. The primary objective of this article is to review the literature concerning classification of hydrogels on different bases, physical and chemical characteristics of these products, and technical feasibility of their utilization. It also involved technologies adopted for hydrogel production together with process design implications, block diagrams, and optimized conditions of the preparation process. An innovated category of recent generations of hydrogel materials was also presented in some details.

  18. Vestibule and Cask Preparation Mechanical Handling Calculation

    Energy Technology Data Exchange (ETDEWEB)

    N. Ambre

    2004-05-26

    The scope of this document is to develop the size, operational envelopes, and major requirements of the equipment to be used in the vestibule, cask preparation area, and the crane maintenance area of the Fuel Handling Facility. This calculation is intended to support the License Application (LA) submittal of December 2004, in accordance with the directive given by DOE correspondence received on the 27th of January 2004 entitled: ''Authorization for Bechtel SAIC Company L.L.C. to Include a Bare Fuel Handling Facility and Increased Aging Capacity in the License Application, Contract Number DE-AC28-01R W12101'' (Ref. 167124). This correspondence was appended by further correspondence received on the 19th of February 2004 entitled: ''Technical Direction to Bechtel SAIC Company L.L. C. for Surface Facility Improvements, Contract Number DE-AC28-01R W12101; TDL No. 04-024'' (Ref. 16875 1). These documents give the authorization for a Fuel Handling Facility to be included in the baseline. The limitations of this preliminary calculation lie within the assumptions of section 5 , as this calculation is part of an evolutionary design process.

  19. Characterization of biochar prepared from biogas digestate.

    Science.gov (United States)

    Hung, Chao-Yi; Tsai, Wen-Tien; Chen, Jie-Wei; Lin, Yu-Quan; Chang, Yuan-Ming

    2017-08-01

    In the study, the biogas digestate was evaluated as a potential feedstock for preparing biochars at a broad temperature range of 300-900°C. The physico-chemical and pore properties of the resulting biochars (denoted as SDBC, solid digestate biochar), including calorific value (higher heating value), surface area/pore volume/pore size distribution, true density, scanning electron microscopy - energy dispersive X-ray spectroscopy (SEM-EDS) and X-ray powder diffraction (XRD), were studied. It was found that the higher heating values of the SDBC products were on a decreasing trend as pyrolysis temperature increased, but they indicated an increase in true density. The results are probably associated with the active pyrolysis of the lignocellulosic fragments and the calcination (or shrinkage) processes, thus resulting in the increased contents of aromatic carbon clusters and main mineral constituents remained. Based on the pore properties, pyrolysis temperature at around 800°C seemed to be the optimal condition for producing SDBC, where its Brunauer-Emmet-Teller (BET) surface area (>100m(2)/g) largely increased as compared to that of the digestate feedstock (700°C) due to the high aromaticity via the thermal decomposition of lignocelluloses and the volatilization of inorganic minerals. Copyright © 2017 Elsevier Ltd. All rights reserved.

  20. Preparation of lanthanum ferrite powder at low temperature

    Energy Technology Data Exchange (ETDEWEB)

    Andoulsi, R.; Horchani-Naifer, K.; Ferid, M., E-mail: karima_horchani@yahoo.com [Physical Chemistry Laboratory of Mineral Materials and their Applications, Hammam-Lif (Tunisia)

    2012-01-15

    Single lanthanum ferrite phase was successfully prepared at low processing temperature using the polymerizable complex method. To implement this work, several techniques such as differential scanning calorimetry, X-ray diffraction, Fourier Transform Infrared Spectroscopy, scanning electron microscopy and BET surface area measurements were used. Throw the obtained results, it was shown that steps of preparing the powder precursor and temperature of its calcination are critical parameters for avoiding phase segregation and obtaining pure lanthanum ferrite compound. Thus, a single perovskite phase was obtained at 600 deg C. At this temperature, the powder was found to be fine and homogeneous with an average crystallite size of 13 nm and a specific surface area of 12.5 m{sup 2}.g{sup -1}. (author)

  1. Preparation of carbon-free TEM microgrids by metal sputtering.

    Science.gov (United States)

    Janbroers, S; de Kruijff, T R; Xu, Q; Kooyman, P J; Zandbergen, H W

    2009-08-01

    A new method for preparing carbon-free, temperature-stable Transmission Electron Microscope (TEM) grids is presented. An 80% Au/20% Pd metal film is deposited onto a 'holey' microgrid carbon supported on standard mixed-mesh Au TEM grids. Subsequently, the carbon film is selectively removed using plasma cleaning. In this way, an all-metal TEM film is made containing the 'same' microgrid as the original carbon film. Although electron transparency of the foil is reduced significantly, the open areas for TEM inspection of material over these areas are maintained. The metal foil can be prepared with various thicknesses and ensures good electrical conductivity. The new Au/Pd grids are stable to at least 775K under vacuum conditions.

  2. Optimal preparation of graph states

    CERN Document Server

    Cabello, Adan; Lopez-Tarrida, Antonio J; Portillo, Jose R

    2010-01-01

    We show how to prepare any graph state of up to 12 qubits with: (a) the minimum number of controlled-Z gates, and (b) the minimum preparation depth. We assume only one-qubit and controlled-Z gates. The method exploits the fact that any graph state belongs to an equivalence class under local Clifford operations. We extend up to 12 qubits the classification of graph states according to their entanglement properties, and identify each class using only a reduced set of invariants. For any state, we provide a circuit with both properties (a) and (b), if it does exist, or, if it does not, one circuit with property (a) and one with property (b), including the explicit one-qubit gates needed.

  3. SEM investigation of Er:YAG laser apical preparation

    Science.gov (United States)

    Bǎlǎbuc, Cosmin; Todea, Carmen; Locovei, Cosmin; RǎduÅ£ǎ, Aurel

    2016-03-01

    Endodontic surgery involves the incision and flap elevation, the access to the root tip, its resection, the cavity retrograde preparation and filling it with biocompatible material that provides a good seal of the apex[1]. Apicoectomy is compulsory in endodontic surgery. The final stage involves the root retropreparation and the carrying out of the retrograde obturation. In order to perform the retrograde preparation the endodontist can use various tools such as lowspeed conventional handpieces, sonic and ultrasonic equipment. The ideal depth of the preparation should be 3 mm, exceeding this value may affect the long-term success of the obturation [2]. Resection at the depth of 3 mm reduces apical ramifications by 98% and lateral root canals by 93%. The ultrasonic retropreparation has numerous advantages compared to the dental drill. Firstly, the cavity will be in the axis of the tooth which implies a minimum destruction of the root canal morphology. The preparations are precise, and the cutting pattern is perpendicular to the long axis of the root, the advantage being the reduction in the number of dentinal tubules exposed at the resected area [3]. Therefore, the retrograde filling is the procedure when an inert and non-toxic material is compacted in the apically created cavity.[4,5]. The Er:YAG laser is the most common wavelength indicated for dental hard tissue preparation. Its natural selectivity offers a significant advantage compared to the conventional hard tissue preparation [6-9].The purpose of this in vitro study was to investigate the quality of Er:YAG laser apical third preparation using Scanning Electron Microscopy (SEM), in comparison with the conventional ultrasonic method.

  4. Method for preparing ceramic composite

    Science.gov (United States)

    Alexander, Kathleen B.; Tiegs, Terry N.; Becher, Paul F.; Waters, Shirley B.

    1996-01-01

    A process for preparing ceramic composite comprising blending TiC particulates, Al.sub.2 O.sub.3 particulates and nickle aluminide and consolidating the mixture at a temperature and pressure sufficient to produce a densified ceramic composite having fracture toughness equal to or greater than 7 MPa m.sup.1/2, a hardness equal to or greater than 18 GPa.

  5. Sample preparation and biopharmaceutical analysis

    OpenAIRE

    Farrelly, Gillian

    1998-01-01

    In chapter 1, an overview is given of sample preparation methods and analytical techniques in use today. Each one is discussed, and relevant examples are given. In chapter 2, the development of a method for the HPLC analysis of taurine in human plasma using acetonitrile precipitation and pre-column derivatisation with fluorescamine is presented. This procedure was found to be faster and easier to use than previous taurine assays. In chapter 3, the evaluation of novel aspirin derivativ...

  6. Ceramic veneers with minimum preparation

    OpenAIRE

    da Cunha, Leonardo Fernandes; Reis, Rachelle; Santana, Lino; Romanini, Jose Carlos; de CARVALHO, Ricardo Marins; Furuse, Adilson Yoshio

    2013-01-01

    The aim of this article is to describe the possibility of improving dental esthetics with low-thickness glass ceramics without major tooth preparation for patients with small to moderate anterior dental wear and little discoloration. For this purpose, a carefully defined treatment planning and a good communication between the clinician and the dental technician helped to maximize enamel preservation, and offered a good treatment option. Moreover, besides restoring esthetics, the restorative t...

  7. A team approach to preparing for hurricanes and other disasters.

    Science.gov (United States)

    Kendig, Jim

    2009-01-01

    Applying lessons learned in Hurricane Floyd in 1999, a three-hospital system located on Florida's exposed Space Coast was able to better deal with the devastation caused by hurricanes in 2004 and make changes in its plans to better prepare for the named storms which hit its area in 2008. Each new disaster, the author points out, brings with it new challenges which have to be considered in disaster planning.

  8. Radiation sterilization of pancreatin preparation

    Energy Technology Data Exchange (ETDEWEB)

    Kimura, Syojiro (Osaka Coll. of Pharmacy, Matsubara (Japan)); Sako, Michiyo; Kanbashi, Toshitaka; Jo, Hisanobu; Koide, Hiroaki

    1984-11-01

    The enzymatic activities (in detail, amylase-, lipase- and protease-activity) of ..gamma..-irradiated pancreatin powder preparation decrease to 50 - 95% at doses range of 50 kR - 8 MR. The dose-inactivation relation-ships vary depending on every different manufactory lot. In the case of higher moisture content preparation as irradiation sample, amylase activities are more stable, the other side, protease activities are less stable. On the variation of these activities by ..gamma..-irradiation, there are no difference between room temperature and lower temperature (-70/sup 0/C) as irradiation condition. The D/sub 10/ values of contained bacteria and fungus (contamination number: about 1 x 10/sup 3/ cells/g and 9 x 10/sup 2/ spores/g) of a pancreatin preparation are 74C/kg (280 kR) and 60 C/kg(230 kR). Then, these values are corresponded to 645 C/kg (2.5 MR) and 540 C/kg (2.1 MR) as perfect sterilization.

  9. Preparing for a dermatopathology quiz

    Directory of Open Access Journals (Sweden)

    Biju Vasudevan

    2014-01-01

    Full Text Available Dermatopathology is one of the key aspects in dermatological diagnosis and is of immense value to the practicing dermatologist as well as residents pursuing dermatology as a career. It is a visual medium of understanding the subject, and is therefore ideal to be tested similarly. Dermatopathology quiz has become a part and parcel of most scientific deliberations, and is therefore an essential requirement of the postgraduate curriculum. Preparing for a dermatopathology quiz is tougher than preparing for a normal clinical quiz because of the lesser importance given for it in the syllabus of postgraduation and also due to the lack of resources either in getting microscopic sessions arranged or due to lack of flair of the subject compared to cosmetology or dermatosurgery. This review was done with the purpose of educating both the students and quizmasters as to how to prepare for a dermatopathology quiz. It is a unique proposal and, therefore, is gathered from more of personal experience, experience gained from watching quizzes conducted by experienced quizmasters, and also from the advice gained from masters of the subject in relation to the quiz.

  10. PREPARATION FOR RETIREMENT - AVS SEMINAR

    CERN Multimedia

    Social Service

    2001-01-01

    The 500 or so participants in the fifth Preparation for Retirement seminar held at the end of March were unfortunately deprived of the planned session on the AVS due to the unavailability of the Director of the Caisse Cantonale Genevoise de Compensation (CCGC). We have since had formal confirmation that because of an extra workload due to important changes in the Swiss tax and social legislation and the implementation this summer of the maternity insurance in Geneva, the CCGC has suspended its participation in preparation for retirement seminars in the international organisations for the time being. Conscious of the necessity of offering a session dedicated to the AVS, it is with pleasure that we can inform you that one of our legal advisers, Mr Lorenz Stampfli, has accepted to lead this session. In order to allow for adequate preparation we have reserved the following date: Wednesday 26 September from 14.00 to 16.00 in the Main Amphitheatre The session will be open to all people already registered and any o...

  11. Selective Suppression of Local Circuits during Movement Preparation in the Mouse Motor Cortex

    Directory of Open Access Journals (Sweden)

    Masashi Hasegawa

    2017-03-01

    Full Text Available Prepared movements are more efficient than those that are not prepared for. Although changes in cortical activity have been observed prior to a forthcoming action, the circuits involved in motor preparation remain unclear. Here, we use in vivo two-photon calcium imaging to uncover changes in the motor cortex during variable waiting periods prior to a forepaw reaching task in mice. Consistent with previous reports, we observed a subset of neurons with increased activity during the waiting period; however, these neurons did not account for the degree of preparation as defined by reaction time (RT. Instead, the suppression of activity of distinct neurons in the same cortical area better accounts for RT. This suppression of neural activity resulted in a distinct and reproducible pattern when mice were well prepared. Thus, the selective suppression of network activity in the motor cortex may be a key feature of prepared movements.

  12. Broadening Cooperation Realm to Promote Stable Development of Shengli Oil Area

    Institute of Scientific and Technical Information of China (English)

    Li Jifu; Yao Shiyu

    1997-01-01

    @@ As the second largest oil area in China, Shengli Petroleum Administration has constantly been strengthening the international cooperation over the recent years in the principal part of the Shengli oil area under the guidance of the national open policy. In venture exploration, data packages have been prepared for the three blocks of Kengdong, Chexi and Qingtuozi with an exploration area of 2370 square kilometers.

  13. 7 CFR 275.18 - Project area/management unit corrective action plan.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 4 2010-01-01 2010-01-01 false Project area/management unit corrective action plan... SYSTEM Corrective Action § 275.18 Project area/management unit corrective action plan. (a) The State agency shall ensure that corrective action plans are prepared at the project area/management unit level...

  14. Preparation of calcium silicate absorbent from iron blast furnace slag.

    Science.gov (United States)

    Brodnax, L F; Rochelle, G T

    2000-09-01

    Calcium silicate hydrate (CSH) solids were prepared from hydrated lime and iron blast furnace slag in an aqueous agitated slurry at 92 degrees C. While it was hoped a minimal lime/slag ratio could be used to create near-amorphous CSH, the surface area of the product improved by increasing the lime/slag weight ratio to 2. The addition of gypsum to the lime/slag system dramatically improved the formation of surface area, creating solids with 139 m2/g after 30 hr of reaction when only a minimal amount of lime was present. The SO2 reactivity of solids prepared with gypsum greatly exceeded that of hydrated lime, achieving greater than 70-80% conversion of the alkalinity after 1 hr of reaction with SO2. The use of CaCl2 as an additive to the lime/slag system, in lieu of gypsum, also produced high-surface-area solids, 115 m2/g after 21 hr of reaction. However, the SO2 reactivity of these sorbents was relatively low given the high surface area. This emphasized that the correlation between surface area and SO2 reactivity was highly dependent on the solid phase, which was subsequently dependent on slurry composition.

  15. Large area mass analyzer

    Energy Technology Data Exchange (ETDEWEB)

    Rachev, Mikhail [Max-Planck-Institut for Nuclear Physics, Heidelberg Saupfercheckweg 1, Heidelberg 69117 (Germany)]. E-mail: mikhail.rachev@mpi-hd.mpg.de; Srama, Ralf [Max-Planck-Institut for Nuclear Physics, Heidelberg Saupfercheckweg 1, Heidelberg 69117 (Germany); Srowig, Andre [Max-Planck-Institut for Nuclear Physics, Heidelberg Saupfercheckweg 1, Heidelberg 69117 (Germany); Gruen, Eberhard [Max-Planck-Institut for Nuclear Physics, Heidelberg Saupfercheckweg 1, Heidelberg 69117 (Germany)

    2004-12-11

    A new time-of-flight spectrometer for the chemical analysis of cosmic dust particles in space has been simulated by Simion 7.0. The instrument is based upon impact ionization. This method is a reliable method for in situ dust detection and is well established. Instruments using the impact ionization flew on board of Helios and Galileo and are still in operation on board of the Ulysses and Cassini-Huygens missions. The new instrument has a large sensitive area of 0.1m2 in order to achieve a significant number of measurements. The mass resolution M/{delta}M>100 and the mass range covers the most relevant elements expected in cosmic dust. The instrument has a reflectron configuration which increases the mass resolution. Most of the ions released during the impact are focused to the detector. The ion detector consists of a large area ion-to-electron converter, an electron reflectron and a microchannel plate detector.

  16. New CO{sub 2} neutral city area with integrated district heating system of the future in Hoeje Taastrup - Phase 1: Preparation of demonstration. Final report; Denmark; Ny CO{sub 2}-neutral bydel med fremtidens integrerede fjernvarmesystem i Hoeje Taastrup - Fase 1: Forberedelse af demonstration. Slutrapport

    Energy Technology Data Exchange (ETDEWEB)

    Kaarup Olsen, P.; Hummelshoej, R.M. (Cowi A/S (Denmark))

    2011-02-15

    three options are interesting. The 'return heat the solution' has less CO{sub 2} displacement potential, but will require a minimal investment cost compared to a regular connection to the HTF/VEKS district heating network. With the assumptions used, the solution with heat-powered pumps and a central solar heating plant provides t a considerably lower CO{sub 2} displacement price than a solution with central ground and solar heating. It is therefore recommended to further analyse the solution with a heat driven heat pump. To make the energy supply of the district CO{sub 2} neutral in the short term, it will be necessary to install wind turbines with a total capacity of approx. 6 MW, which for that particular area at this time would be the most cost-effective solution, i.e. will have the lowest CO{sub 2} displacement price. (LN)

  17. New CO{sub 2} neutral city area with integrated district heating system of the future in Hoeje Taastrup - Phase 1: Preparation of demonstration. Final report; Denmark; Ny CO{sub 2}-neutral bydel med fremtidens integrerede fjernvarmesystem i Hoeje Taastrup - Fase 1: Forberedelse af demonstration. Slutrapport

    Energy Technology Data Exchange (ETDEWEB)

    Kaarup Olsen, P.; Hummelshoej, R.M. (Cowi A/S (Denmark))

    2011-02-15

    three options are interesting. The 'return heat the solution' has less CO{sub 2} displacement potential, but will require a minimal investment cost compared to a regular connection to the HTF/VEKS district heating network. With the assumptions used, the solution with heat-powered pumps and a central solar heating plant provides t a considerably lower CO{sub 2} displacement price than a solution with central ground and solar heating. It is therefore recommended to further analyse the solution with a heat driven heat pump. To make the energy supply of the district CO{sub 2} neutral in the short term, it will be necessary to install wind turbines with a total capacity of approx. 6 MW, which for that particular area at this time would be the most cost-effective solution, i.e. will have the lowest CO{sub 2} displacement price. (LN)

  18. Sacramento Metropolitan Area, California

    Science.gov (United States)

    1992-02-01

    resource of the river. Also, strips of riparian vegetation along the riverbank provide good areas for naturalists and birdwatching . Recreational resources...policies #1 and #2 when improvements are made costing at least 50 percent of the estimated current market value of the structure before improvements. o1 S 0...height and depth of flooding is provided in Table 1. Although depreciation values have been used in our analysis, market values also had to be considered

  19. Frostbites in circumpolar areas

    Directory of Open Access Journals (Sweden)

    Tiina Maria Ikäheimo

    2011-10-01

    Full Text Available Circumpolar areas are associated with prolonged cold exposure where wind, precipitation, and darkness further aggravate the environmental conditions and the associated risks. Despite the climate warming, cold climatic conditions will prevail in circumpolar areas and contribute to adverse health effects. Frostbite is a freezing injury where localized damage affects the skin and other tissues. It occurs during occupational or leisure-time activities and is common in the general population among men and women of various ages. Industries of the circumpolar areas where frostbite occurs frequently include transportation, mining, oil, and gas industry, construction, agriculture, and military operations. Cold injuries may also occur during leisure-time activities involving substantial cold exposure, such as mountaineering, skiing, and snowmobiling. Accidental situations (occupational, leisure time often contribute to adverse cooling and cold injuries. Several environmental (temperature, wind, wetness, cold objects, and altitude and individual (behavior, health, and physiology predisposing factors are connected with frostbite injuries. Vulnerable populations include those having a chronic disease (cardiovascular, diabetes, and depression, children and the elderly, or homeless people. Frostbite results in sequelae causing different types of discomfort and functional limitations that may persist for years. A frostbite injury is preventable, and hence, unacceptable from a public health perspective. Appropriate cold risk management includes awareness of the adverse effects of cold, individual adjustment of cold exposure and clothing, or in occupational context different organizational and technical measures. In addition, vulnerable population groups need customized information and care for proper prevention of frostbites.

  20. Vehicular road influence areas

    Science.gov (United States)

    Huertas, María E.; Huertas, José I.; Valencia, Alexander

    2017-02-01

    Vehicle operation over paved and unpaved roads is an emission source that significantly contributes to air pollution. Emissions are derived from vehicle exhaust pipes and re-suspension of particulate matter generated by wind erosion and tire to road surface interactions. Environmental authorities require a methodology to evaluate road impact areas, which enable managers to initiate counter-measures, particularly under circumstances where historic meteorological and/or air quality data is unavailable. The present study describes an analytical and experimental work developed to establish a simplified methodology to estimate the area influenced by vehicular roads. AERMOD was chosen to model pollutant dispersion generated by two roads of common attributes (straight road over flat terrain) under the effects of several arbitrary chosen weather conditions. The resulting pollutant concentration vs. Distance curves collapsed into a single curve when concentration and distance were expressed as dimensionless numbers and this curve can be described by a beta distribution function. This result implied that average concentration at a given distance was proportional to emission intensity and that it showed minor sensitivity to meteorological conditions. Therefore, road influence was defined by the area adjacent to the road limited by distance at which the beta distribution function equaled the limiting value specified by the national air quality standard for the pollutant under consideration.

  1. SUBURBAN AREAS. ZONAS SUBURBANAS.

    Directory of Open Access Journals (Sweden)

    Diana Valencia Londoño

    2014-06-01

    Full Text Available RESUMEN: The suburban areas represent a category of use and appropriation of the soil that is particularly problematic in the Latin American context. The conflicts that tend to occur in this type of areas are given by the uncontrolled expansion of cities in a competition with the rural areas which deprives these from various environmental conditions and positive housing conditions. This article is the product of the research project “Methodology for the Intervention of Suburban Soils, Northern Aburra: A Case Study” in Medellin, Colombia, in order to disseminate core concepts that guide the study and generate academic exchange in this regard. Resumen: Las zonas suburbanas representan una categoría de uso y apropiación del suelo que es particularmente problemática en el contexto latinoamericano. Los conflictos que suelen verificarse en este tipo de zonas se dan por la expansión incontrolada de las ciudades en una competencia con las áreas rurales que priva a éstas de varias de sus condiciones ambientales y de habitabilidad positivas. El artículo es producto del proyecto de investigación “Metodología para la intervención de suelos suburbanos, caso de estudio Aburrá Norte” en Medellín, Colombia, con el fin de divulgar los conceptos de base que orientan el estudio y generar intercambio académico al respecto.

  2. Mission-Area Guide to Lead-Exposure Control

    Science.gov (United States)

    1996-03-01

    Dentistry needs an elastic impression material that takes accurate, one-piece impressions of undercut areas (for inlay and crown preparations). Types of...Management and Budget. 1987. Stannard, Jan G., Materials in Dentistry , Denali Publishing. Boston, MA, 1986. Sullivan, Jim, Headquarters, Army...Lead-Exposure Control March 1996 63 DOD Memorandum, SUBJECT: Modification of Pediatric Blood Lead Screening Program, June 26, 1995. Universal

  3. Area Handbook for the People's Republic of China.

    Science.gov (United States)

    Whitaker, Donald P.; Shinn, Rinn-Sup

    This volume on the People's Republic of China is one of a series of handbooks prepared by the Foreign Area Studies (FAS) of the American University, designed to be useful to military and other personnel who need a convenient compilation of basic facts about the social, economic, political, and military institutions and practices of various…

  4. Research on Fish Consumer Profile Evaluation in Romanian Plain Area

    Directory of Open Access Journals (Sweden)

    Silvius STANCIU

    2011-11-01

    Full Text Available Research aimed at shaping a fish consumer profile in the Romanian Plain area. 150 people were interviewed. Preferences evaluation was conducted by means of a questionnaire with 27 questions. Favorite fish species, purchasing place and manner, favorite preparation choices, consumption frequency and place have been identified.

  5. Workshop on problem areas associated with developing carcinogen guidelines

    Energy Technology Data Exchange (ETDEWEB)

    1984-06-01

    A workshop was conducted to discuss problem areas associated with developing carcinogen guidelines. Session topics included (1) definition of a carcinogen for regulatory purposes; (2) potency; (3) risk assessment; (4) uncertainties; (5) de minimis quantity; and (6) legal and regulatory issues. Separate abstracts have been prepared for individual papers. (ACR)

  6. All Conservation Opportunity Areas (ECO.RES.ALL_OP_AREAS)

    Data.gov (United States)

    U.S. Environmental Protection Agency — The All_OP_Areas GIS layer are all the Conservation Opportunity Areas identified by MoRAP (produced for EPA Region 7). They designate areas with potential for...

  7. 75 FR 41163 - Notice of Intent To Prepare an Environmental Impact Statement and Overseas Environmental Impact...

    Science.gov (United States)

    2010-07-15

    ... National Environmental Policy Act (NEPA) of 1969, as implemented by the Council on Environmental Quality... area does not include the Arctic. This EIS and OEIS is being prepared to renew and combine current... responsibility (except for the Arctic). The AFTT study area covers approximately 2.6 million square...

  8. Silver Vanadium Phosphorous Oxide, Ag(2)VO(2)PO(4): Chimie Douce Preparation and Resulting Lithium Cell Electrochemistry.

    Science.gov (United States)

    Kim, Young Jin; Marschilok, Amy C; Takeuchi, Kenneth J; Takeuchi, Esther S

    2011-08-15

    Recently, we have shown silver vanadium phosphorous oxide (Ag(2)VO(2)PO(4), SVPO) to be a promising cathode material for lithium based batteries. Whereas the first reported preparation of SVPO employed an elevated pressure, hydrothermal approach, we report herein a novel ambient pressure synthesis method to prepare SVPO, where our chimie douce preparation is readily scalable and provides material with a smaller, more consistent particle size and higher surface area relative to SVPO prepared via the hydrothermal method. Lithium electrochemical cells utilizing SVPO cathodes made by our new process show improved power capability under constant current and pulse conditions over cells containing cathode from SVPO prepared via the hydrothermal method.

  9. The Quantitative Preparation of Future Geoscience Graduate Students

    Science.gov (United States)

    Manduca, C. A.; Hancock, G. S.

    2006-12-01

    Modern geoscience is a highly quantitative science. In February, a small group of faculty and graduate students from across the country met to discuss the quantitative preparation of geoscience majors for graduate school. The group included ten faculty supervising graduate students in quantitative areas spanning the earth, atmosphere, and ocean sciences; five current graduate students in these areas; and five faculty teaching undergraduate students in the spectrum of institutions preparing students for graduate work. Discussion focused in four key ares: Are incoming graduate students adequately prepared for the quantitative aspects of graduate geoscience programs? What are the essential quantitative skills are that are required for success in graduate school? What are perceived as the important courses to prepare students for the quantitative aspects of graduate school? What programs/resources would be valuable in helping faculty/departments improve the quantitative preparation of students? The participants concluded that strengthening the quantitative preparation of undergraduate geoscience majors would increase their opportunities in graduate school. While specifics differed amongst disciplines, a special importance was placed on developing the ability to use quantitative skills to solve geoscience problems. This requires the ability to pose problems so they can be addressed quantitatively, understand the relationship between quantitative concepts and physical representations, visualize mathematics, test the reasonableness of quantitative results, creatively move forward from existing models/techniques/approaches, and move between quantitative and verbal descriptions. A list of important quantitative competencies desirable in incoming graduate students includes mechanical skills in basic mathematics, functions, multi-variate analysis, statistics and calculus, as well as skills in logical analysis and the ability to learn independently in quantitative ways

  10. Bioequivalence of three florfenicol preparations in broilers

    Directory of Open Access Journals (Sweden)

    Husamettin Ekici

    2014-12-01

    Full Text Available This study was aimed to determine the bioequivalence of three different preparations of florfenicol using non-drugged broiler chickens. A total of 28 broiler chickens aging 30-day were divided into four equal groups; these were Group I, II, III, and IV. The birds of Group I (for effective substance were given intravenous (i.v. administration of florfenicol dosed at 40 mg/kg body weight (b.wt.. The birds of Group II (for reference drug, Group III (for test-1 drug, and Group IV (for test-2 drug received florfenicol preparations with water (dosed at 40 mg/kg b.wt. through intracrop administration. Blood samples were collected periodically from the birds of all four groups, and blood plasma was separated. Levels of florfenicol and its metabolite (florfenicol amine in the plasma were measured by High Performance Liquid Chromatography (HPLC. In this study, the limit of detection (LOD for florfenicol and florfenicol amine were recorded as 0.017 and 0.78 µg/mL, respectively. On the other hand, the recovery of florfenicol and florfenicol amine were 83.4-84.6 and 82.2-83.8%, respectively. Based on the values of area under the curve (AUC, maximum concentration (Cmax, and time to maximum concentration (Tmax, test-1 drug was found to be acceptable, whereas test-2 drug was remained below the acceptable limits (80-125% of AUC and Cmax. Thus, it was concluded that test-1 drug was bioequivalent as compared to the reference drug.

  11. Sample Preparation for Bioanalytical and Pharmaceutical Analysis.

    Science.gov (United States)

    Clark, Kevin D; Zhang, Cheng; Anderson, Jared L

    2016-12-06

    Biological and pharmaceutical samples represent formidable challenges in sample preparation that hold important consequences for bioanalysis and genotoxic impurity quantification. This Feature will emphasize significant advances toward the development of rapid, sensitive, and selective sample preparation methods.

  12. A Simple Preparation Method for Diphosphoimidazole

    DEFF Research Database (Denmark)

    Rosenberg, T.

    1964-01-01

    A simple method for the preparation of diphosphoimidazole is presented that involves direct phosphorylation of imidazole by phosphorus oxychloride in alkaline aqueous solution. Details are given on the use of diphosphoimidazole in preparing sodium phosphoramidate and certain phosphorylated amino...

  13. Preparation and characterization of antigenic properties of ...

    African Journals Online (AJOL)

    PRECIOUS

    2009-12-15

    Dec 15, 2009 ... A rapid, simple and low cost procedure for preparing hapten-protein conjugates was developed using .... using a GS-800 Calibrated Densitometer (Bio-rad, USA). .... is to develop a method to prepare effective immunogens.

  14. Method of surface preparation of niobium

    Science.gov (United States)

    Srinivasan-Rao, Triveni; Schill, John F.

    2003-01-01

    The present invention is for a method of preparing a surface of niobium. The preparation method includes polishing, cleaning, baking and irradiating the niobium surface whereby the resulting niobium surface has a high quantum efficiency.

  15. FFTF operations procedures preparation guide. Revision 2

    Energy Technology Data Exchange (ETDEWEB)

    1976-12-01

    The Guide is intended to provide guidelines for the initial preparation of FFTF Operating Procedures. The Procedures Preparation Guide was developed from the plan presented and approved in the FFTF Reactor Plant Procedures Plan, PC-1, Revision 3.

  16. 40 CFR 1502.6 - Interdisciplinary preparation.

    Science.gov (United States)

    2010-07-01

    ... § 1502.6 Interdisciplinary preparation. Environmental impact statements shall be prepared using an inter-disciplinary approach which will insure the integrated use of the natural and social sciences and...

  17. Patient's perception of location, form and size in case of cavity preparation.

    Science.gov (United States)

    Isoya, Kazuhiro; Sasaki, Yoshiyuki; Mataki, Shiro

    2004-06-01

    The aim of the present study was to clarify the difference between the imagination of patients and the reality in regard to the location, the form and the size of the cavity in case of cavity preparation for dental restoration. Firstly, we manufactured the dummy dentition for simulated cavity preparation and the operator intra-orally prepared a cavity on the dummy dentition in subject to confirm its validity. Then, 5 operators intra-orally prepared prescribed cavities at the both sides of maxillary first molars on the dummy dentition in every one of 5 subjects with masking. We compared the location, the form and the area of these prepared cavities with those imagined by subjects, respectively. In 58% of cases, the subjects could accurately recognize the location of prepared teeth. And 34% of cases also determined the Class of cavity form. The imagined area was larger than the actual area and the difference was statistically significant (p cavity preparation and patients tended to overestimate amounts of removed tooth substance.

  18. Small Area Fair Market Rent

    Data.gov (United States)

    Department of Housing and Urban Development — Due to the increasing demand for more localized rents for a variety of purposes, HUD is making Small Area FMRs for all metropolitan areas available. Small Area FMRs...

  19. Large area bulk superconductors

    Science.gov (United States)

    Miller, Dean J.; Field, Michael B.

    2002-01-01

    A bulk superconductor having a thickness of not less than about 100 microns is carried by a polycrystalline textured substrate having misorientation angles at the surface thereof not greater than about 15.degree.; the bulk superconductor may have a thickness of not less than about 100 microns and a surface area of not less than about 50 cm.sup.2. The textured substrate may have a thickness not less than about 10 microns and misorientation angles at the surface thereof not greater than about 15.degree.. Also disclosed is a process of manufacturing the bulk superconductor and the polycrystalline biaxially textured substrate material.

  20. Beyond breeding area management

    DEFF Research Database (Denmark)

    Pedersen, Lykke; Thorup, Kasper; Tøttrup, Anders P.

    Every year, billions of songbirds migrate thousands of kilometres between their European breeding grounds and African overwintering area. As migratory birds are dependent on resources at a number of sites varying in both space and time, they are likely to be more vulnerable to environmental change...... technological advances are currently enabling us to track yet smaller songbirds throughout their migration cycle providing valuable insight into the life cycle of individual birds. However, direct tracking of migratory birds has so far mainly been conducted on single populations and our understanding of entire...... and provide important information for conservation management of migratory birds....

  1. Dementia in Taiwan area

    Institute of Scientific and Technical Information of China (English)

    Yuanhan Yang

    2016-01-01

    Objective:Taiwan has an increasing aging population like other developed areas. The aging population will lead to an increased prevalence of dementia. Methods:This article will reflect the status of dementia in Taiwan, including updated epidemiology, diagnosis, subtypes, and optimal treatment of dementia. Results:The article also describes and interprets the Taiwan Dementia Policy to establish a clear, large view of the current state of management of dementia in Taiwan and future policy implementation. Conclusion:A comprehensive policy to dementia, from the basic researches to clinical care and treatment, is necessary to the increased aged population in Taiwan.

  2. Zeolites and Usage Areas

    Directory of Open Access Journals (Sweden)

    Jale Gülen

    2012-06-01

    Full Text Available Zeolites are formed via several reactions from the minerals that consist of aluminium and silica. Zeolites, which have a growing significance in recent days are one of important industrial raw materials. As well as being used as a catalyst, theirability to do ion exchange and adsorption make them even more valuable. Zeolites are used in several industries such as energy, agriculture and animal husbandry, mining and metallurgy, construction, detergent, paper, etc. In this study, the definiton, formation and usage areas of zeolites are explained.

  3. Cholera in Azov area

    OpenAIRE

    O. N. Domashenko; T. A. Belomerya; N. V. Martynova; G. N. Daragan; Demkovich, O.O.; U. V. Malakhova; G. I. Zemlyanskaya; Popova, D.M.

    2015-01-01

    The purpose of research is analysis of clinical course and treatment results of patients with cholera in the Azov area. Materials and methods. During the period from 29.05.2011 to 19.08.2011 33 cases of cholera (32 adults and 1 child) and 25 vibrio carriers (22 adults and 3 children), which were caused by toxigenic strains of Vibrio cholera El Tor serogroup O1 Ogawa. Results. Likely factors of disease transmission in Mariupol are sea and river water, and the fish that were caught in the water...

  4. Rhenium Nanochemistry for Catalyst Preparation

    Directory of Open Access Journals (Sweden)

    Vadim G. Kessler

    2012-08-01

    Full Text Available The review presents synthetic approaches to modern rhenium-based catalysts. Creation of an active center is considered as a process of obtaining a nanoparticle or a molecule, immobilized within a matrix of the substrate. Selective chemical routes to preparation of particles of rhenium alloys, rhenium oxides and the molecules of alkyltrioxorhenium, and their insertion into porous structure of zeolites, ordered mesoporous MCM matrices, anodic mesoporous alumina, and porous transition metal oxides are considered. Structure-property relationships are traced for these catalysts in relation to such processes as alkylation and isomerization, olefin metathesis, selective oxidation of olefins, methanol to formaldehyde conversion, etc.

  5. STS Interventions: Preparing, Defending, Learning

    Directory of Open Access Journals (Sweden)

    Brian Martin

    2016-06-01

    Full Text Available Intervening in the Australian vaccination debate, I found that STS perspectives helped me understand the controversy but gave little guidance on how to defend against attacks. Max Liboiron comments that preparation, including support networks, should precede interventions. I was well supported in my involvement in the vaccination debate, but those who openly advocate a stigmatized view may have difficulty gaining support. Teun Zuiderent-Jerak asks what is being learned when interventions reinforce existing categories. Controversy participants can learn by being exposed to STS perspectives; controversy researchers, when attacked, can gain new information and develop new research ideas.

  6. [CORPSE CONSERVATION: ATTILIO MAGGIA'S PREPARATIONS].

    Science.gov (United States)

    Porro, Alessandro; Franchini, Antonia Francesca; Galimberti, Paolo M; Lorusso, Lorenzo; Falconi, Bruno

    2015-01-01

    The authors analyze Attilio Maggia's method of corpse conservation. His method was based on development of formaline vapours and preservation of corpse into a hermetically closed coffin (U.S.Patent 1150688 - Aug. 17, 1915). The corpses preserved could also be hardened after the treatment, exposing them to the air. Attilio Maggia (1864-1945) treated the corpse of italian writer Giovanni Verga (1840-1922). Some Maggia's preparations were preserved into obstetrical museum at Milan University: they are lost, but some records remain (an old inventory register) and attest us the industry of this physician.

  7. Preparation of Manganese Oxide Nanobelts

    Institute of Scientific and Technical Information of China (English)

    Jisen WANG; Jinquan SUN; Ying BAO; Xiufang BIAN

    2003-01-01

    Oriented nanobelts of manganese oxide have been firstly and successfully prepared by a microemulsion techniqueunder controlled circumstances. The samples were characterized by X-ray diffraction (XRD), transmission electronmicroscope (TEM). Influences of sodium chloride and annealed temperature on the synthesis of Mn3O4 nanobeltswere investigated. It was found that NaCl is the key factor to synthesize oriented Mn3O4 nanobelts and 827 K isoptimum temperature to produce fine nanobelts. Oriented growth mechanism of Mn3O4 nanobelts was discussed.

  8. Trends in mask data preparation

    Science.gov (United States)

    Fujimura, Aki; Pang, Liyong; Su, Bo; Choi, Yohan

    2014-10-01

    Whether for VSB mask writing or for multibeam mask writing, the shapes we need to write on masks are increasingly complex, increasingly curvilinear, and smaller in minimum width and space. The overwhelming trend in mask data preparation (MDP) is the shift from deterministic, rule-based, geometric, context-independent, shape-modulated, rectangular processing to statistical, simulation-based, context-dependent, dose- and shape-modulated any-shape processing. The paper briefly surveys the history of MDP, and explains through a simulation-based study that 50nm line and space is the tipping point where rule-based processing gives away to simulation-based processing.

  9. Carbonaceous Chondrite Thin Section Preparation

    Science.gov (United States)

    Harrington, R.; Righter, K.

    2017-01-01

    Carbonaceous chondrite meteorites have long posed a challenge for thin section makers. The variability in sample hardness among the different types, and sometimes within individual sections, creates the need for an adaptable approach at each step of the thin section making process. This poster will share some of the procedural adjustments that have proven to be successful at the NASA JSC Meteorite Thin Section Laboratory. These adjustments are modifications of preparation methods that have been in use for decades and therefore do not require investment in new technology or materials.

  10. Ceramic veneers with minimum preparation.

    Science.gov (United States)

    da Cunha, Leonardo Fernandes; Reis, Rachelle; Santana, Lino; Romanini, Jose Carlos; Carvalho, Ricardo Marins; Furuse, Adilson Yoshio

    2013-10-01

    The aim of this article is to describe the possibility of improving dental esthetics with low-thickness glass ceramics without major tooth preparation for patients with small to moderate anterior dental wear and little discoloration. For this purpose, a carefully defined treatment planning and a good communication between the clinician and the dental technician helped to maximize enamel preservation, and offered a good treatment option. Moreover, besides restoring esthetics, the restorative treatment also improved the function of the anterior guidance. It can be concluded that the conservative use of minimum thickness ceramic laminate veneers may provide satisfactory esthetic outcomes while preserving the dental structure.

  11. Dissipative preparation of entanglement in optical cavities

    DEFF Research Database (Denmark)

    Kastoryano, Michael James; Reiter, Florentin; Sørensen, Anders Søndberg

    2011-01-01

    We propose a novel scheme for the preparation of a maximally entangled state of two atoms in an optical cavity. Starting from an arbitrary initial state, a singlet state is prepared as the unique fixed point of a dissipative quantum dynamical process. In our scheme, cavity decay is no longer...... as compared to preparation protocols based on coherent unitary dynamics...

  12. Preparation for your Foreign Learning Experience

    NARCIS (Netherlands)

    Jos Walenkamp; Manuela Hernandez

    2012-01-01

    It is a well-known fact that a good preparation in the pre-departure stage can maximize the chances of a succesful foreign experience. But what is meant by a good preparation? And what are the expected results of such a preparation? This course focuses in internship and study abroad (pre-departure)

  13. Preparation for your Foreign Learning Experience

    NARCIS (Netherlands)

    Manuela Hernandez; Jos Walenkamp

    2015-01-01

    It is a well-known fact that a good preparation in the pre-departure stage can maximize the chances of a succesful foreign experience. But what is meant by a good preparation? And what are the expected results of such a preparation? This course focuses in internship and study abroad (pre-departure)

  14. Analysis of Offshore Wind Energy Leasing Areas for the Rhode Island/Massachusetts Wind Energy Area

    Energy Technology Data Exchange (ETDEWEB)

    Musial, W.; Elliott, D.; Fields, J.; Parker, Z.; Scott, G.

    2013-04-01

    The National Renewable Energy Laboratory (NREL), under an interagency agreement with the Bureau of Ocean Energy Management (BOEM), is providing technical assistance to BOEM on the identification and delineation of offshore leasing areas for offshore wind energy development within the Atlantic Coast Wind Energy Areas (WEAs) established by BOEM in 2012. This report focuses on NREL's evaluation of BOEM's Rhode Island/Massachusetts (RIMA) WEA leasing areas. The objective of the NREL evaluation was to assess the proposed delineation of the two leasing areas and determine if the division is reasonable and technically sound. Additionally, the evaluation aimed to identify any deficiencies in the delineation. As part of the review, NREL performed the following tasks: 1. Performed a limited review of relevant literature and RIMA call nominations. 2. Executed a quantitative analysis and comparison of the two proposed leasing areas 3. Conducted interviews with University of Rhode Island (URI) staff involved with the URI Special Area Management Plan (SAMP) 4. Prepared this draft report summarizing the key findings.

  15. How to select BCAA preparations.

    Science.gov (United States)

    Kato, Akinobu; Suzuki, Kazuyuki

    2004-12-01

    In Japan, oral branched-chain amino acid (BCAA) preparations are used in nutritional therapy for correcting disorders of protein and amino acid metabolism in patients with liver cirrhosis. There are two forms of oral BCAA preparations: enteral nutrition products for liver failure (or elemental nutrition products for liver cirrhosis) and oral BCAA granular products. Granular products are indicated for patients with uncompensated liver cirrhosis who have no dietary restriction and hypoproteinemia. Enteral nutrition products are indicated for patients who have a history of hepatic encephalopathy and exhibit protein intolerance. In clinical practice, the existence of protein intolerance in patients with uncompensated liver cirrhosis should be determined based on a history of hepatic encephalopathy and blood ammonia concentration. When patients exhibit protein intolerance, they are given a low protein diet (approximately 0.5-1.0g/kg/day) with enteral nutrition products for liver failure. However, when patients consume adequate amounts of a well-balanced diet and ammonia concentration does not increase, it is possible to control their condition with granular products. However, when patients cannot achieve an adequate dietary intake, it is recommended that enteral nutrition products should be used in order to improve nutritional status, even if these patients do not have a history of encephalopathy.

  16. Preparation and Crystallization of Riboswitches.

    Science.gov (United States)

    Peselis, Alla; Gao, Ang; Serganov, Alexander

    2016-01-01

    Recent studies have revealed that the majority of biological processes are controlled by noncoding RNAs. Among many classes of noncoding RNAs, metabolite-sensing segments of mRNAs called riboswitches are unique. Discovered over a decade ago in all three kingdoms of life, riboswitches specifically and directly interact with various metabolites and regulate expression of multiple genes, often associated with metabolism and transport of small molecules. Thus, riboswitches do not depend on proteins for binding to small molecules and play a role as both metabolite sensors and effectors of gene control. Riboswitches are typically located in the untranslated regions of mRNAs where they form alternative structures in the presence and absence of the ligand and modulate expression of genes through the formation of regulatory elements. To understand the mechanism of the riboswitch-driven gene control, it is important to elucidate how riboswitches interact with cognate and discriminate against non-cognate ligands. Here we outline the methodology to synthesize riboswitch RNAs and prepare riboswitch-ligand complexes for crystallographic and biochemical studies. The chapter describes how to design, prepare, and conduct crystallization screening of riboswitch-ligand complexes. The methodology was refined on crystallographic studies of several riboswitches and can be employed for other types of RNA molecules.

  17. MUET Preparation Language Learning Strategies

    Directory of Open Access Journals (Sweden)

    Yoong Li Kuen

    2012-01-01

    Full Text Available The main objective of the study was to examine the English language learning strategies (LLS used by Lower Six students in secondary schools who are sitting for their MUET test. It analyzed the language learning strategies that students use in order to prepare for the MUET test. Data were collected using a survey questionnaire with 300 students. The instrument used in this study called “MUET Preparation Language Strategy Use Inventory” is an adapted and bilingual questionnaire designed by Cohen, Oxford and Chi (2005 known as Language Strategy Use Inventory. Forty items were analyzed and they comprised of the four skills tested in MUET which is listening, speaking, reading and writing. Data were analyzed by performing frequency analysis. The findings revealed that the listening skill is the most frequently used, while the writing skill is the least frequently used. Only the listening skill has high frequency of use, while the reading, speaking and writing skills fall under the range of moderate frequency of use. There were variations in responses with regard to the use of LLS among Form Six students in secondary schools. The findings had practical implications.

  18. Preparation of hydrophobic organic aeorgels

    Science.gov (United States)

    Baumann, Theodore F.; Satcher, Jr., Joe H.; Gash, Alexander E.

    2007-11-06

    Synthetic methods for the preparation of hydrophobic organics aerogels. One method involves the sol-gel polymerization of 1,3-dimethoxybenzene or 1,3,5-trimethoxybenzene with formaldehyde in non-aqueous solvents. Using a procedure analogous to the preparation of resorcinol-formaldehyde (RF) aerogels, this approach generates wet gels that can be dried using either supercritical solvent extraction to generate the new organic aerogels or air dried to produce an xerogel. Other methods involve the sol-gel polymerization of 1,3,5 trihydroxy benzene (phloroglucinol) or 1,3 dihydroxy benzene (resorcinol) and various aldehydes in non-aqueous solvents. These methods use a procedure analogous to the one-step base and two-step base/acid catalyzed polycondensation of phloroglucinol and formaldehyde, but the base catalyst used is triethylamine. These methods can be applied to a variety of other sol-gel precursors and solvent systems. These hydrophobic organics aerogels have numerous application potentials in the field of material absorbers and water-proof insulation.

  19. Proximate composition of plant origin traditional foods from Black Sea Area Countries

    OpenAIRE

    Albuquerque, T.G.; Costa, H. S.; A. Sanches-Silva; Fontes, T.; Mota, C.; Santos, M; Vasilopoulou, E; Trichopoulou, A.; D’Antuono, F.; Alexieva, I.; Fedosova, K.; Karpenko, D.; Kilasonia, Z.; Kocaoglu, B.; Koval, N.

    2011-01-01

    Within the frame of the European Project BaSeFood (Sustainable Exploitation of Bioactive Components Black Sea Area traditional foods), thirty-three traditional foods from six Black Sea Area Countries (Bulgaria, Georgia, Romania, Russian Federation, Turkey and Ukraine) were selected and prepared according to the traditional recipe, ingredients and traditional preparation methods. The aim is to promote and preserve traditional foods and to produce new and reliable data of the overall nutritiona...

  20. Preparing Mathematical Equations in a Document Preparation Environment

    Institute of Scientific and Technical Information of China (English)

    郑民; 卢金鑫

    1994-01-01

    WITS-Math is a mathematical equation formatting tool in WITS,a multilingual document preparation environment.WITS-Math includes a library manager and an equation formatter.The main task of WITS-Math is to format diversities of mathematical equations and organize them into an equation library used by other tools in the WITS environment.WITS-Math is a direct manipulation mathematics editor.It uses syntax directed markup language as the internal representation,and provides an interactive WYSI-WYG interface for users to format equations.WITS-Math provides an equation access mechanism.Other tools can access equations in a library br cross-reference from a source file or through data exchange without knowing the structure of equation libraries.The common data structure and the rendering object in the WITS platform ensure that the formatted equations can be directly used by other tools.

  1. Wide area sensor network

    Science.gov (United States)

    Mukhopadhyay, Sanjoy; Nix, Tricia; Junker, Robert; Brentano, Josef; Khona, Dhiren

    2006-05-01

    The technical concept for this project has existed since the Chernobyl accident in 1986. A host of Eastern European nations have developed countrywide grid of sensors to monitor airborne radiation. The objective is to build a radiological sensor network for real-time monitoring of environmental radiation levels in order to provide data for warning, and consequentially the assessment of a nuclear event. A network of radiation measuring equipment consisting of gamma, neutron, alpha, and beta counters would be distributed over a large area (preferably on fire station roof tops) and connected by a wireless network to the emergency response center. The networks would be deployed in urban environments and would supply first responders and federal augmentation teams (including those from the U.S. Departments of Energy, Defense, Justice, and Homeland Security) with detailed, accurate information regarding the transport of radioactive environmental contaminants, so the agencies can provide a safe and effective response. A networked sensor capability would be developed, with fixed sensors deployed at key locations and in sufficient numbers, to provide adequate coverage for early warning, and input to post-event emergency response. An overall system description and specification will be provided, including detector characteristics, communication protocols, infrastructure and maintenance requirements, and operation procedures. The system/network can be designed for a specifically identified urban area, or for a general urban area scalable to cities of specified size. Data collected via the network will be transmitted directly to the appropriate emergency response center and shared with multiple agencies via the Internet or an Intranet. The data collected will be managed using commercial off - the - shelf Geographical Information System (GIS). The data will be stored in a database and the GIS software will aid in analysis and management of the data. Unique features of the

  2. Phoenix Work Area Animation

    Science.gov (United States)

    2008-01-01

    [figure removed for brevity, see original site] Click on image for animation This animation from Sol 1 shows a mosaic of the Phoenix digging area in the Martian terrain. Phoenix scientists are very pleased with this view as the terrain features few rocks an optimal place for digging. The mast of the camera looks disjointed because the photos that comprise this mosaic were taken at different times of day. This video also show some of the lander's instrumentation. The Phoenix Mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver.

  3. Local area networks

    CERN Document Server

    Zafiropoulo, P

    1982-01-01

    Pitro Zafiropulo is a- staff member at the IBM Research Laboratories at Zurich. He joined IBM in 1968 and has worked on protocol validation, synthesis, integrated networks, network reliability, PABX's and speech recognition. Local Area Networks are intended to provide improved communication capabilities such as high data throughput rates, low error rates and ease of connection among terminal stations and comuters. These new types of networks operate within a limited geographical range like an establishment, campus or building and are owned by a single organization. The presentation introduces these networks and the main techniques are described. It then proceeds to evaluate the main switching techniques as they apply to LAN ring and bus configurations. The preferred technique of token-ring distributed switching is identified. The contents of Mr. Zafiropoulo's talk was somewhat similar to the paper of Mr. Kummerle, which is therefore included in these Proceedings.

  4. Surface area and conductivity of polyaniline synthesized under UV irradiation

    Science.gov (United States)

    Budi, S.; Fitri, E.; Paristiowati, M.; Cahyana, U.; Pusparini, E.; Nasbey, H.; Imaddudin, A.

    2017-02-01

    This paper reports our study on the synthesis of high electrical conductivity and surface area polyaniline using oxidative polymerization under UV light irradiation. The formation of emeraldine structures of polyaniline was revealed by major absorption bands of FTIR (Fourier transform infrared spectroscopy) spectra attributed to C-N stretching, C=C stretching in the benzenoid ring, C=C stretching in the quinoid ring and QNH+B stretching. XRD (X-ray diffractometer) measurements confirmed typical diffraction patterns with a crystallinity of 13% and 16% for polyaniline prepared under non-stirred and stirred reaction, respectively. SEM (Scanning electron microscope) studies showed more uniform morphology of polyaniline was obtained with stirring reaction process compare to those prepared without stirring. Surface analysis using SAA (surface area analyzer) showed that pure polyaniline with the relatively high surface area of ca.28 m2/g was successfully prepared in this work. Based on four point probe measurement, the prepared polyaniline possesses high conductivity which is important in electrode application.

  5. Preparation of Porous ZrO2 and Study on Its Properties

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The porous zirconia powder with a high surface area was synthesized by means of the ion exchange method from surfactant CTMAB. The highest surface area of the resulted zirconia reached 340 m2/g having been calcined at 500 ℃ for 2 h. The influence of preparing conditions on the surface area was investigated. The results show that the amount of the surfactant and the aging time were two main factors affecting the surface area of zirconia. The IR analysis indicated that the large surface area was related to the cations of the surfactant which incorporated into hydrous zirconia by ion exchange.

  6. Preparation of Biopolymer Aerogels Using Green Solvents

    Science.gov (United States)

    Subrahmanyam, Raman; Gurikov, Pavel; Meissner, Imke; Smirnova, Irina

    2016-01-01

    Although the first reports on aerogels made by Kistler1 in the 1930s dealt with aerogels from both inorganic oxides (silica and others) and biopolymers (gelatin, agar, cellulose), only recently have biomasses been recognized as an abundant source of chemically diverse macromolecules for functional aerogel materials. Biopolymer aerogels (pectin, alginate, chitosan, cellulose, etc.) exhibit both specific inheritable functions of starting biopolymers and distinctive features of aerogels (80-99% porosity and specific surface up to 800 m2/g). This synergy of properties makes biopolymer aerogels promising candidates for a wide gamut of applications such as thermal insulation, tissue engineering and regenerative medicine, drug delivery systems, functional foods, catalysts, adsorbents and sensors. This work demonstrates the use of pressurized carbon dioxide (5 MPa) for the ionic cross linking of amidated pectin into hydrogels. Initially a biopolymer/salt dispersion is prepared in water. Under pressurized CO2 conditions, the pH of the biopolymer solution is lowered to 3 which releases the crosslinking cations from the salt to bind with the biopolymer yielding hydrogels. Solvent exchange to ethanol and further supercritical CO2 drying (10 - 12 MPa) yield aerogels. Obtained aerogels are ultra-porous with low density (as low as 0.02 g/cm3), high specific surface area (350 - 500 m2/g) and pore volume (3 - 7 cm3/g for pore sizes less than 150 nm). PMID:27403649

  7. Preparation and Analysis of Biomass Lignins

    Science.gov (United States)

    Compere, Alicia L.; Griffith, William L.

    Lignin, comprised primarily of three randomly polymerized phenylpropenyl monomers, is, arguably, the second most common organic molecule on earth. In current biorefinery applications, lignin is burned, usually in concentrated pulping or hydrolysis liquor, as a source of process steam and both internal and exported electricity. The aromatic content of lignin makes it a potentially attractive feedstock for high-value aromatic chemicals, polymers, and carbon products (graphite, activated carbon, and carbon fiber). Revenue from production of lignin-based chemicals could play a major role in biorefinery profitability if cost-effective methods for lignin separation and purification can be developed. This chapter presents descriptions of methods for assessing and purifying biorefinery lignins so that they can be evaluated for use as feedstock for production of chemical products. Areas covered are: (1) initial evaluations of as-received lignin samples (visual, microscopic, separable organics); (2) analysis of common contaminants (bulk and filterable ash and particulate contaminants in liquid and dry lignin samples); (3) preparation of lignins for experimental use as chemical feedstock (prefiltration, filtration using bench-scale chemical apparatus and larger scale bag filters, one-step lignin precipitation, two-step carbohydrate and lignin precipitation, desalting of dry powdered or precipitated lignin, and lyophilization). These methods have been used successfully at the bench scale to produce the 1-50 kg amounts of wood and grass lignins typically required for bench-scale assessment as chemical feedstocks.

  8. Preparing Today's Nursing Students for Tomorrow's Career.

    Science.gov (United States)

    Wynn, Stephanie

    2016-01-01

    Federal directives, nursing and nursing education associations, as well as accrediting bodies emphasize the importance of integrating health information technology and EHRs into nursing practice. Additionally, informatics is a required competency of baccalaureate nursing graduates. Nursing education's efforts to enhance students' learning in the area of electronic documentation is at its peak. The goal of enabling nurses to make healthcare safer, more effective, efficient, patient-centered, timely and equitable can only be achieved if a variety of technologies are clearly integrated into nursing education. Therefore, some schools have developed educational innovations to incorporate academic EHRs. As the mental health setting is unique, extraordinary attention has to be provided during the education of electronic documentation. Nursing education efforts must focus on interventions that provide resources that enhance the participant's knowledge and skills related to electronic documentation in a variety of clinical settings. Additionally, implementing academic EHRs in clinical settings offers nursing educators an opportunity to note the benefits. The state of nursing education depends on the accessibility to utilize academic EHRs in the nursing curriculum within the clinical setting to effectively prepare students for real-word practice.

  9. Preparation of the SPS as LHC injector

    CERN Document Server

    Collier, Paul

    1998-01-01

    A major project (SLI) for the preparation the SPS in its role as the final link in the injector chain to the LHC was launched one year ago [1,2]. The major areas of work include the upgrade of the RF and the injection systems, together with the provision of a new extraction channel to serve ring 2 of the LHC. In addition, studies have been made on the ability of the SPS to meet the stringent trans verse and longitudinal beam requirements of the LHC. This has lead to several other programmes of work including upgrades to the beam instrumentation, the transverse damper and the shielding of over 8 00 inter-magnet pumping ports to reduce the impedance of the machine. The planning of the project is influenced by the continued operation of LEP and the proposed new long base-line neutrino facility (NGS). In addition, during the machine upgrades, the SPS must continue to deliver high quality proton beams to the fixed-target experimental community and for an extensive range of experimental detect or test beams. The ma...

  10. Preparation and Characterization of Manganese Ferrite Aluminates

    Directory of Open Access Journals (Sweden)

    R. L. Dhiman

    2008-01-01

    Full Text Available Aluminum doped manganese ferrites MnAlxFe2−xO4 with 0.0≤x≤1.0 have been prepared by the double ceramic route. The formation of mixed spinel phase has been confirmed by X-ray diffraction analysis. The unit cell parameter `aO' is found to decrease linearly with aluminum concentration due to smaller ionic radius of aluminum. The cation distributions were estimated from X-ray diffraction intensities of various planes. The theoretical lattice parameter, X-ray density, oxygen positional parameter, ionic radii, jump length, and bonds and edges lengths of the tetrahedral (A and octahedral (B sites were determined. 57Fe Mössbauer spectra recorded at room temperature were fitted with two sextets corresponding to Fe3+ ions at A- and B-sites. In the present ferrite system, the area ratio of Fe3+ ions at the A- and B-sites determined from the spectral analysis of Mössbauer spectra gives evidence that Al3+ ions replace iron ions at B-sites. This change in the site preference reflects an abrupt change in magnetic hyperfine fields at A- and B-sites as aluminum concentration increases, which has been explained on the basis of supertransferred hyperfine field. On the basis of estimated cation distribution, it is concluded that aluminum doped manganese ferrites exhibit a 55% normal spinel structure.

  11. Improving Technical, Tactical and Psychological Preparation of Freestyle Wrestlers

    Directory of Open Access Journals (Sweden)

    Pakulin Serhij

    2016-12-01

    Full Text Available Objectives: 1 to justify the ways of improvement of training free style wrestlers to improve the results of their activities and competitive sports skills; 2 to identify the areas of improvement of psychological preparation and the structure of complex psycho-pedagogical methods for optimizing mental condition of free style wrestlers. Material and methods: The following methods were used in the study: analysis and synthesis of the scientific data of methodological literature; pedagogical supervision; survey (interview, questionnaire; analysis of freestyle wrestlers competitive activity; testing of physical and psychological fitness; pedagogical experiment; methods of mathematical and statistical analysis of research results. Results: it has been demonstrated that there is a necessity to improve technical, tactical and psychological preparation of freestyle fighters; the basic problems of the process have been defined. Conclusion: 1 the method of preparation of freestyle wrestlers has been grounded and the feasibility of its use for rapid making the best technical and tactical decisions in a competitive activity has been proved. It is proposed to include specific tactical training methods for each action and various combinations of basic actions into the coach program of wrestling; 2 the directions of improving psychological preparation and the structure of complex psychological and pedagogical methods of optimizing the mental condition of free style wrestlers are substantiated.

  12. Preparation, sintering and leaching of optimized uranium thorium dioxides

    Science.gov (United States)

    Hingant, N.; Clavier, N.; Dacheux, N.; Barre, N.; Hubert, S.; Obbade, S.; Taborda, F.; Abraham, F.

    2009-03-01

    Mixed actinide dioxides are currently studied as potential fuels for several concepts associated to the fourth generation of nuclear reactors. These solids are generally obtained through dry chemistry processes from powder mixtures but could present some heterogeneity in the distribution of the cations in the solid. In this context, wet chemistry methods were set up for the preparation of U1-xThxO2 solid solutions as model compounds for advanced dioxide fuels. Two chemical routes of preparation, involving the precipitation of crystallized precursor, were investigated: on the one hand, a mixture of acidic solutions containing cations and oxalic acid was introduced in an open vessel, leading to a poorly-crystallized precipitate. On the other hand, the starting mixture was placed in an acid digestion bomb then set in an oven in order to reach hydrothermal conditions. By this way, small single-crystals were obtained then characterized by several techniques including XRD and SEM. The great differences in terms of morphology and crystallization state of the samples were correlated to an important variation of the specific surface area of the oxides prepared after heating, then the microstructure of the sintered pellets prepared at high temperature. Preliminary leaching tests were finally undertaken in dynamic conditions (i.e. with high renewal of the leachate) in order to evaluate the influence of the sample morphology on the chemical durability of the final cohesive materials.

  13. [Preparation and utility of glibenclamide suppository for hospital use].

    Science.gov (United States)

    Takahashi, Y; Iwata, M; Shirotake, S; Takayama, K; Machida, Y; Nagai, T

    1998-09-01

    Glibenclamide (GC) is widely used as an oral hypoglycemic drug in the treatment of non-insulin dependent diabetes mellitus (NIDDM). Since GC is usually taken for a long period, side effects and noncompliance are among the problems. In order to solve those problems, we prepared GC suppositories and examined their usefulness. Suppositories containing 4, 20, and 40 mg of GC were prepared and examined for drug release, drug absorption and blood glucose levels after the rectal administration of suppositories in rabbits. In the release test, GC suppositories released the drug continuously for 6 hours. The areas under the drug release time curve (ADT) of 20 and 40 mg GC suppositories were 3.5 and 6.2 times of 4 mg GC suppositories respectively. The plasma concentrations after administration of 4 and 20 mg GC suppositories showed about the same profiles for 6 hours. After administration of 40 mg GC suppositories, the maximum plasma concentration (Cmax) was observed at 2 hours. All the GC suppositories showed lower blood glucose levels compared with the control. The remainder of the area under the blood glucose concentration time curve between the control (RAUC) in the case of 40 mg GC suppository was 1.3 times larger than that of the 4 mg GC suppository. The GC suppositories sufficiently lowered the blood glucose levels. These results suggest that the GC suppositories should be useful in the hospital preparation for the treatment of NIDDM patients.

  14. Urea adsorption by activated carbon prepared from palm kernel shell

    Science.gov (United States)

    Ooi, Chee-Heong; Sim, Yoke-Leng; Yeoh, Fei-Yee

    2017-07-01

    Dialysis treatment is crucial for patients suffer from renal failure. The dialysis system removes the uremic toxin to a safe level in a patient's body. One of the major limitations of the current hemodialysis system is the capability to efficiently remove uremic toxins from patient's body. Nanoporous materials can be applied to improve the treatment. Palm kernel shell (PKS) biomass generated from palm oil mills can be utilized to prepare high quality nanoporous activated carbon (AC) and applied for urea adsorption in the dialysis system. In this study, AC was prepared from PKS via different carbonization temperatures and followed by carbon dioxide gas activation processes. The physical and chemical properties of the samples were studied. The results show that the porous AC with BET surface areas ranging from 541 to 622 m2g-1 and with total pore volumes varying from 0.254 to 0.297 cm3g-1, are formed with different carbonization temperatures. The equilibrium constant for urea adsorption by AC samples carbonized at 400, 500 and 600 °C are 0.091, 0.287 and 0.334, respectively. The increase of carbonization temperatures from 400 to 600 °C resulted in the increase in urea adsorption by AC predominantly due to increase in surface area. The present study reveals the feasibility of preparing AC with good porosity from PKS and potentially applied in urea adsorption application.

  15. Detailed planning to upgrade the sterile-products preparation area to a cleanroom.

    Science.gov (United States)

    Wright, B

    1995-08-15

    In a project to establish a cleanroom, the pharmacy manager is the person who must motivate everyone and keep the momentum going. Involving departments other than pharmacy is the key to success. The project provides an opportunity to improve the department's performance with the aid of other departments.

  16. Tucannon River Temperature Study, Prepared for : Watershed Resource Inventory Area (WRIA) 35.

    Energy Technology Data Exchange (ETDEWEB)

    HDR Engineering.

    2006-06-30

    This report presents the results of a temperature analysis of the Tucannon River completed for the WRIA 35 Planning Unit. The Tucannon River is located in southeastern Washington and flows approximately 100 kilometers (km) (62 miles) from the Blue Mountains to the Snake River. High water temperature in the Tucannon River has been identified as a limiting factor for salmonid fish habitat (Columbia Conservation District, 2004). Several segments of the Tucannon River are included on Washington State Department of Ecology (Ecology) 303(d) list of impaired waterbodies due to temperature. Ecology is currently conducting scoping for a temperature Total Maximum Daily Load (TMDL) study of the Tucannon River. The WRIA 35 Planning Unit retained HDR Engineering to evaluate water temperature in the Tucannon River. The project objectives are: (1) Review recent and historic data and studies to characterize temperature conditions in the river; (2) Perform field studies and analyses to identify and quantify heating and cooling processes in the river; (3) Develop and calibrate a computer temperature model to determine the sources of heat to the Tucannon River and to predict the temperature of the river that would occur with increased natural riparian shading assuming the current river morphology; (4) Evaluate differences in river temperatures between current and improved riparian shading during the 'critical' period - low river flows and high temperatures; and (5) Determine the potential benefits of riparian shading as a mechanism to decrease river temperature.

  17. 75 FR 522 - National Emission Standards for Hazardous Air Pollutants: Area Source Standards for Prepared...

    Science.gov (United States)

    2010-01-05

    ... that ``drop filter socks'' be used on bulk loaders. The final rule requires that emissions from the... emissions. The proposed rule required that the pressure drop across the cyclone be monitored to demonstrate... rule allows monitoring of inlet flow rate, inlet velocity, pressure drop, or fan amperage. C....

  18. 75 FR 63447 - Intent To Prepare a Draft Environmental Impact Statement for the Louisiana Coastal Area...

    Science.gov (United States)

    2010-10-15

    ... be consulted regarding the ``Swampbuster'' provisions of the Food Security Act. Coordination will be..., program governance, implementation, and other program components. The LCA restoration program...

  19. Road Investment Design in Areas Protected by the Monuments Conservator

    Science.gov (United States)

    Juszczyk, Artur

    2016-06-01

    Design works on road construction plans for areas protected by conservation require a proper preparation, especially in terms of formality, which has been described in this paper. One has shown the various methods of conduct in the course of obtaining administrative decisions and related difficulties, which are dependent on the form of monument protection and the scope of the proposed building works. One has also raised a question regarding the law on the subject. One has suggested the consolidation of existing regulations and introduced the likely new direction that is currently in preparation.

  20. Preparation of Bauxite Ceramic Microsphere

    Institute of Scientific and Technical Information of China (English)

    CHENG Xiaosu; LIU Pingan; LI Xiuyan; SHUI Anze; ZENG Lingke

    2007-01-01

    Ceramic microspheres were prepared by using Chinese bauxite as raw materials through the centrifugal spray drying method. The control technology of microsphere size, degree of sphericity was researched. The ceramic microspheres were sintered by a double sintering process. The microstructure and composition of ceramic microsphere were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and X-ray energy spectroscopy. The results show that the degree of sphericity of the ceramic microsphere was good and the particle size was 10-100 μm. The XRD analysis reveals that the main crystalline phase of the ceramic microsphere was α- Al2O3 and mullite (3Al2O3·2SiO2). The product can be used as reinforced material for composite material, especially for antiskid and hard wearing aluminum alloy coating.

  1. Preparation of High Shrinkage Polypropylene

    Institute of Scientific and Technical Information of China (English)

    吕文军; 王华平; 李建梅; 张玉梅

    2001-01-01

    The common PP chips have been used to prepare high shrinkage PP fibers with shrinkage in boiling water higher than 50%. Meanwhile, the process conditions on fiber structure and properties have been discussed in detail. With the increase of drawing temperature, the shrinkage in boiling water of the fiber increases at first,and then decreases in the temperature range from 70℃ to 100℃. The better drawing temperature is from 75℃ to 85℃ according to the melt index of the PP material. The shrinkage in boiling water of PP fiber increases with the increase of pump delivery. The orientation factor and crystallinity increase with the increase of drawing temperature. With an increase in drawing temperature,unit-cell numbers and monomer unit numbers in every crystal nucleus tend to increase, but unit volume crystal nucleus tend to reduce.

  2. Microfluidic Sample Preparation for Immunoassays

    Energy Technology Data Exchange (ETDEWEB)

    Visuri, S; Benett, W; Bettencourt, K; Chang, J; Fisher, K; Hamilton, J; Krulevitch, P; Park, C; Stockton, C; Tarte, L; Wang, A; Wilson, T

    2001-08-09

    Researchers at Lawrence Livermore National Laboratory are developing means to collect and identify fluid-based biological pathogens in the forms of proteins, viruses, and bacteria. to support detection instruments, they are developing a flexible fluidic sample preparation unit. The overall goal of this Microfluidic Module is to input a fluid sample, containing background particulates and potentially target compounds, and deliver a processed sample for detection. They are developing techniques for sample purification, mixing, and filtration that would be useful to many applications including immunologic and nucleic acid assays. Many of these fluidic functions are accomplished with acoustic radiation pressure or dielectrophoresis. They are integrating these technologies into packaged systems with pumps and valves to control fluid flow through the fluidic circuit.

  3. Preparation of uncladded YBCO wires

    Science.gov (United States)

    Grader, G.; Cadoche, L.; Shter, G.

    1993-04-01

    Wires of YBCO, 1-5 mm in diameter, have been obtained by extrusion of an oxalate derived powder mixed with polyvinyl butyral (PVB) and two phthalate plasticizers. The densification and transport properties of the wires were investigated at various organic loading conditions. For YBCO powder prepared by oxalate coprecipitation and calcined at 930°C, the maximal strength, relative density and Jc were 20MPa, 92% and 400A/cm 2, respectively. Results show that after a 4-hour sintering at 955°C the tensile strength, density, and Jc are all maximized at a binder content of 3-4 wt.%. The loading of up to 10 wt.% dibutyl phthalate (DBP) plasticizer (in the binder) has little effect on the properties. Beyond this loading a drastic drop in Jc is observed. The densification was very poor for sinterings below 950°C, which was reflected by a lower critical current.

  4. Aerosol preparation of intact lipoproteins

    Energy Technology Data Exchange (ETDEWEB)

    Benner, W. Henry (Danville, CA); Krauss, Ronald M (Berkeley, CA); Blanche, Patricia J (Berkeley, CA)

    2012-01-17

    A medical diagnostic method and instrumentation system for analyzing noncovalently bonded agglomerated biological particles is described. The method and system comprises: a method of preparation for the biological particles; an electrospray generator; an alpha particle radiation source; a differential mobility analyzer; a particle counter; and data acquisition and analysis means. The medical device is useful for the assessment of human diseases, such as cardiac disease risk and hyperlipidemia, by rapid quantitative analysis of lipoprotein fraction densities. Initially, purification procedures are described to reduce an initial blood sample to an analytical input to the instrument. The measured sizes from the analytical sample are correlated with densities, resulting in a spectrum of lipoprotein densities. The lipoprotein density distribution can then be used to characterize cardiac and other lipid-related health risks.

  5. Preparing Physicists for Paperless Pedagogy

    Science.gov (United States)

    Fuller, Robert G.

    1996-11-01

    Electronic databases, CD-ROMs and the World Wide Web are making large amounts of physics information in electronic form available to physics faculty members. As we seek to educate the next generation of physicists we need to explore the positive and negative aspects of teaching without using paper. We are preparing to offer a experimental version of calculus-based physics that will use a CD-ROM instead of a printed text. The homework and examinations will be done electronically. The laboratory experiments will be microcomputer-based activities and will include multimedia. This presentation will examine the positive and negative features of print as well as introduce the promises and pitfalls of the electronic teaching of physics. Some time for discussion will be left at the end of the presentation. Members of the audience will surely have comments and suggestions overlooked by the author.

  6. Sonochemical Preparation of Polymer Nanocomposites

    Directory of Open Access Journals (Sweden)

    Hyoung Jin Choi

    2009-06-01

    Full Text Available Thisreview covers sonochemical fabrication of polymer nanocomposites. In addition to its application to the synthesis of various polymeric systems, due to its powerful efficiency, sonochemistry has been widely used not only as the assistant of dispersion for nanomaterials such as carbon nanotubes (CNT and organophillic clay, but also as a special initiator to enhance polymerization for fabrication of polymer nanocomposites with CNT and metallic nanoparticles. Recent developments in the preparation of multi-walled carbon nanotube/polymer nanocomposites with polystyrene and PMMA, magnetic particle/CNT composites and polymer/clay nanocomposites along with their physical characteristics and potential engineering applications will be introduced. Physical characterizations include morphological, thermal, and rheological properties under either an applied electric or magnetic field.

  7. [Bifidogenic factors as drug preparations].

    Science.gov (United States)

    Murashova, A O; Lisitsin, O B; Abramov, N A

    1999-01-01

    The review of new data on the study of bifidobacterial factors of different origin and the probable mechanisms of their favorable action on the microflora of the intestinal tract if presented. The main emphasis is made on the analysis of data on the use of oligosaccharides, including fructo-oligosaccharides, as compounds stimulating the growth and development of bifidobacteria both in pure cultures and in intestinal microflora. Methods for the treatment of natural compounds with a view to enhancing their bifidogenic effect are presented. The possibilities and/or advantages of using bifidogenic factors in vivo and in vitro as medicinal preparations either alone or incorporated in probiotic compositions are evaluated. Suggestion has been made that the choice of the method for using bifidogenic factors may depend on the kind and severity of disturbances in indigenous microflora.

  8. Solo but Not Separate: Preparing 21st-Century School Library Professionals Who Can "Go It Alone"

    Science.gov (United States)

    Pasco, Becky

    2011-01-01

    Preparing school librarians for a diverse array of 21st-century educational environments is a daunting task. Faculty in school library preparation programs send candidates out into sparsely populated rural areas, dense urban settings, and everything in between. Some candidates will provide services and resources in updated, modern facilities,…

  9. Global protected area impacts.

    Science.gov (United States)

    Joppa, Lucas N; Pfaff, Alexander

    2011-06-01

    Protected areas (PAs) dominate conservation efforts. They will probably play a role in future climate policies too, as global payments may reward local reductions of loss of natural land cover. We estimate the impact of PAs on natural land cover within each of 147 countries by comparing outcomes inside PAs with outcomes outside. We use 'matching' (or 'apples to apples') for land characteristics to control for the fact that PAs very often are non-randomly distributed across their national landscapes. Protection tends towards land that, if unprotected, is less likely than average to be cleared. For 75 per cent of countries, we find protection does reduce conversion of natural land cover. However, for approximately 80 per cent of countries, our global results also confirm (following smaller-scale studies) that controlling for land characteristics reduces estimated impact by half or more. This shows the importance of controlling for at least a few key land characteristics. Further, we show that impacts vary considerably within a country (i.e. across a landscape): protection achieves less on lands far from roads, far from cities and on steeper slopes. Thus, while planners are, of course, constrained by other conservation priorities and costs, they could target higher impacts to earn more global payments for reduced deforestation.

  10. MANAGEMENT IN RURAL AREAS

    Directory of Open Access Journals (Sweden)

    Danimir Štros

    2015-07-01

    Full Text Available Croatia has been seeking to achive pre-war results in tourism since its independence. Rural tourism in Croatia based on family farma faces a number of problems legal foundations, the involement of local communities, inadequate entepreneur support etc. The political will for development exists, but there is lack of willingness and the ability to get things started, which results in the closure of family farma who cannot cope with the parallel job of agriculture and tourism. Arriving guests certainly want a new type of tourism: peace, clean environment, cultural intangible and tangible treasures, all without the noise and stress; and Croatia can definitely offer it, either in coastal or inland areas with traditional food and drinks. The destinations connection is not satisfactora. there is also an evident lack of legislation and regional spatial development plans for sustainable tourism which is a prerequisite for successful tourism. With these plans presumptins accepted, Croatian tourism would become distinctive and inland and coastal branches of tourism could complement each other so that the customer can spend his vacation both in the continental ant the maritime part of the country, getting to know our culture and enjoy the traditional cousine.

  11. Plant Community Traits of Shohada Protected Area, West Azerbijan, Iran

    Directory of Open Access Journals (Sweden)

    Abdollah HASSANZADEH GORTTAPEH

    2010-03-01

    Full Text Available Shohada Protected Area, consisting of Shohada Valley and its adjacent areas with an area of 577 hectares is located in south of Urmia, and is known as an important natural plant station of Urmia. It is studied with respect to the important factors which influence the vegetation cover in whole, particularly, with regard the composition and formation of plant communities. To study the area, Brown-Blanquets method was used. Plant samples were taken from 77 sample plots. The study resulted in recognition of four herbaceous types and seven shrub types in the studied area. In addition, the investigation led to the fact that the most important factors which influence the vegetation cover, are: geographical orientation, altitude, gradient and soil texture. The study also resulted in preparation of a colored vegetation map with a scale of 1:20000.

  12. An overview of Preparation, Evaluation and Applications of Multiple Emulsions

    Directory of Open Access Journals (Sweden)

    Sandip Prajapati

    2013-04-01

    Full Text Available Multiple emulsions are also known as emulsions of emulsions, liquid membrane system or double emulsion. Multiple emulsions are polydispersed systems where both oil in water & water in oil emulsions exist simultaneously. This review focuses on preparation, characterization and potential applications of multiple emulsions. Multiple emulsions can be classified as water-in oil-in water (W/O/W or oil-in-water-in-oil (O/W/O emulsions. This review described five methods to prepare multiple emulsions viz. two-step emulsification method, modified two-step emulsification method, phase inversion method, membrane emulsification & micro channel emulsification method. The Multiple emulsion is characterized by average globule size & size distribution, area of interfaces, number of globules, rheological evaluation, zeta potential, percentage drug entrapment, In-vitro drug release. Multiple emulsions have been proposed to have numerous uses including their use as prolonged drug delivery system.

  13. PREPARATION AND CHARACTERIZATION OF POLYMER-BASED SPHERICAL ACTIVATED CARBONS

    Institute of Scientific and Technical Information of China (English)

    Zhao-lian Zhu; Ai-min Li; Ming-fang Xia; Jin-nan Wan; Quan-xing Zhang

    2008-01-01

    A series of spherical activated carbons(SACs)with different pore structures were prepared from chloromethylated polydivinylbenzene by ZnCl2 activation.The effects of activation temperature and retention time on the yield and textural properties of the resulting SACs were studied.All the SACs are generated with high yield of above 65% and exhibit relatively high mesopore fraction(me%) of 35.7%-43.6% compared with conventional activated carbons.The sample zlc28 prepared at 800℃ for 2 h has the largest BET surface area of 891m2g-1 and pore volume of 0.489 cm3g-1,SEM and XRD analyses of zlc28 verify the presence of developed porous structure composed of disordered micrographite stacking with large amounts of interspaces in the order of nanometers.

  14. The Role of Educators in Preparing the Confident Graduate Student

    Directory of Open Access Journals (Sweden)

    Geri Dickey, PhD

    2016-08-01

    Full Text Available With large numbers of non-BSW graduates gravitating toward MSW programs of study, BSWs must demonstrate their ability to handle the rigor of graduate school in order to remain competitive in the classroom and field. This study utilized an online survey of MSW students (N=107 from four different universities to examine how well students believe their particular undergraduate degree program prepared them to meet the academic demands of the MSW programs. Bivariate and multivariate analyses were performed and results indicate BSW graduates feel more prepared than non-BSWs to complete their MSW program. The exception for BSWs was found in areas of research and statistics when compared specifically to those with psychology bachelor degrees.

  15. Preparation and electrocatalytic properties of tungsten carbide electrocatalysts

    Institute of Scientific and Technical Information of China (English)

    马淳安; 张文魁; 成旦红; 周邦新

    2002-01-01

    The tungsten carbide(WC) electrocatalysts with definite phase components and high specific surface area were prepared by gas-solid reduction method. The crystal structure, phase components and electrochemical properties of the as-prepared materials were characterized by XRD, BET(Brunauer Emmett and Teller Procedure) and electrochemical test techniques. It is shown that the tungsten carbide catalysts with definite phase components can be obtained by controlling the carburizing conditions including temperature, gas flowing rate and duration time. The electrocatalysts with the major phase of W2C show higher electrocatalytic activity for the hydrogen evolution reaction. The electrocatalysts with the major phase of WC are suitable to be used as the anodic electrocatalyst for hydrogen anodic oxidation, which exhibit higher hydrogen anodic oxidation electrocatalytic properties in HCl solutions.

  16. Preparation of nanosized non-oxide powders using diatomaceous earth

    Directory of Open Access Journals (Sweden)

    Šaponjić A.

    2009-01-01

    Full Text Available In this paper the nanosized non-oxide powders were prepared by carbothermal reduction and subsequent nitridation of diatomaceous earth which is a waste product from coal exploitation. Our scope was to investigate the potential use of diatomaceous earth as a main precursor for low-cost nanosized non-oxide powder preparation as well as to solve an environmental problem. The influence of carbon materials (carbonized sucrose, carbon cryogel and carbon black as a reducing agent on synthesis and properties of low-cost nanosized nonoxide powders was also studied. The powders were characterized by specific surface area, X-ray and SEM investigations. It was found that by using diatomaceous earth it is was possible to produce either a mixture of non-oxide powders (Si3N4/SiC or pure SiC powders depending on temperature.

  17. IMPROVEMENTS OF RIVER MODELING 1D DATA PREPARATION

    Directory of Open Access Journals (Sweden)

    ION-MARIAN MOISOIU

    2012-11-01

    Full Text Available Improvements of river modeling 1D data preparation. The importance of hydrographical networks data and the need for detailed studies do generate an increase of projects in this specialized area and a diversification of river mathematical modeling software. River mathematical modeling can be done in two ways, namely; the "2D mode" and the “1D mode”. The “2D mode” is where a digital terrain model of a full hydrographical basin must be produced and "1D mode" is where only cross sections, long sections and structures elevations needs to be presented in a graphical environment and in a specific formats for the mathematical modeling software. This paper will show the principle of a custom built GIS, specially created to help the preparation of 1D river modeling data. The benefits are; elimination of human errors, automated processing, increasing productivity, flexible output and cost reduction.

  18. Structure of silicon oxide films prepared by vacuum deposition

    Science.gov (United States)

    Saito, Yoshio; Kaito, Chihiro; Nishio, Kenzo; Naiki, Toshio

    1985-05-01

    The structure of thin silicon oxide films 5 nm in thickness, which were prepared by electron beam evaporation of SiO 2 glass onto a NaCl substrate, has been examined by high resolution electron microscopy and diffraction. Although the films which were prepared with substrate temperatures ranging from room up to 400°C gave rise to amorphous haloes, lattice fringes in areas 1-2 nm in extent were, however, seen in the micrographs. It is shown that the film is composed of α-quartz micro-crystallites. Crystals of α-cristobalite with sizes of several tens of nanometers appeared at a substrate temperature of 500°C. At a substrate temperature of 600°C, β-cristobalite crystals with sizes of several tens of nanometers appeared. The structural changes due to the substrate temperature were attributed to incorporation of sodium atoms from the substrate into the SiO 2 film.

  19. Preparing the SPS for LHC

    CERN Document Server

    Linnecar, Trevor Paul R

    1997-01-01

    The beams that the SPS must accelerate to fill the LHC have stringent requirements both transversely and longitudinally. The single bunch and total intensities have been obtained separately in the past but now have to be produced simultaneously and must be concentrated in a small part of the machine circumference. The transverse emittances will be small as will the allowable blow-up from injection to extraction. Beams with the LHC parameters will not be available in the SPS until the upgrades in the pre-injector chain are finished. Nevertheless a programme of studies is being carried out to examine the different areas where problems might occur. The delicate areas are at injection where single and coupled bunch instabilities have to be controlled in the longitudinal plane and where transverse emittance blow-up is expected, and at top energy where complicated RF gymnastics are required and where longitudinal coupled bunch instabilites can develop on the long flat top.

  20. H. W. Laboratory manual: 100 Area section

    Energy Technology Data Exchange (ETDEWEB)

    1950-07-01

    The purpose of this manual is to present a Hazard Breakdown of all jobs normally encountered in the laboratory work of the three sections comprising the Analytic Section, Metallurgy and Control Division of the Technical Department. A Hazard Breakdown is a careful analysis of any job in which the source of possible dangers is clearly indicated for each particular step. The analysis is prepared by individuals who are thoroughly familiar with the specific job or procedure. It is felt that if the hazards herein outlined are recognized by the Laboratory personnel and the suggested safety cautions followed, the chance for injury will be minimized and the worker will become generally more safety conscious. The manual, which is prefaced by the general safety rules applying to all the laboratories, is divided into three main sections, one for each of the three sections into which the Laboratories Division is divided. These sections are as follows: Section 1 -- 200 Area Control; Section 2 -- 100 Area Control; Section 3 -- 300 Area Control, Essential Materials, and Methods Improvement.

  1. Water Service Areas - Public Water Supplier's (PWS) Service Areas

    Data.gov (United States)

    NSGIC Education | GIS Inventory — Boundaries of current public water supplier's (PWS) service areas. This data set contains the present service area boundary of the water system and does not contain...

  2. Water Service Areas - Public Water Supplier's (PWS) Service Areas

    Data.gov (United States)

    NSGIC GIS Inventory (aka Ramona) — Boundaries of current public water supplier's (PWS) service areas. This data set contains the present service area boundary of the water system and does not contain...

  3. Education Prepares for the Future

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Hubei Province is making efforts to make school children in ethnic areas better understand their culture wang Sirui,8,is a grade-3 pupil at the Ethnic Primary School of Enshi Tujia and Miao Autonomous Prefecture (shortened as Enshi Prefecture (shortened as Enshi Prefecture), central China’s Hubei Province. Although from the Tujia ethnic group, the little girl knew little about the Tujia culture before she came to study in the school in 2008.

  4. CT study of the performance of reciprocating and oscillatory motions in flattened root canal areas

    Energy Technology Data Exchange (ETDEWEB)

    Moura-Netto, Cacio, E-mail: caciomn@usp.br [Universidade Cruzeiro do Sul (UNICSUL), Sao Paulo, SP (Brazil). Fac. de Odontologia; Palo, Renato Miotto [Universidade Estadual Paulista Julio de Mesquita Filho (ICT/UNESP), Sao Jose dos Campos, SP (Brazil). Instituto de Ciencia e Tecnologia; Pinto, Larissa Fernanda; Daltoe, Gisele; Mello-Moura, Anna Carolina Volpi [Universidade Ibirapuera (UNIB), Sao Paulo, SP (Brazil). Fac. de Odontologia

    2015-03-01

    Abstract: Root canal preparation is an important step in endodontic treatment. The anatomical complexity of the middle third of the root compromises the effective cleaning of this area. Thus, advances have been made in instrumentation techniques and instruments for this purpose. The aim of this study was to evaluate the effects of three different instrumentation systems on the enlargement of the middle thirds of root canals in mandibular incisors. The preparation methods used were the reciprocating systems Reciproc (Group I) and WaveOne (Group II) and the oscillatory system Tilos (Group III). Comparisons were made by three-dimensional image reconstruction with cone-beam computed tomography before and after instrumentation. Changes in area, perimeter, centering ability, and pattern of preparation were analyzed. The results were subjected to ANOVA complemented by the Tukey’s test. Changes in area, perimeter, and tendency of transportation showed similar results among groups. The transportation index of the Tilos system was significantly lower than that of the other groups. Qualitative analysis of the preparation pattern showed that the Tilos system had a more uniform preparation, although Reciproc and WaveOne preparations appeared more rounded, incompatible with the original canal anatomy. There was similarity in the systems’ performance on flattened areas, although the Tilos system presented a better pattern of root canal preparation and a lower index of transportation. (author)

  5. CT study of the performance of reciprocating and oscillatory motions in flattened root canal areas

    Directory of Open Access Journals (Sweden)

    Cacio MOURA-NETTO

    2015-01-01

    Full Text Available Root canal preparation is an important step in endodontic treatment. The anatomical complexity of the middle third of the root compromises the effective cleaning of this area. Thus, advances have been made in instrumentation techniques and instruments for this purpose. The aim of this study was to evaluate the effects of three different instrumentation systems on the enlargement of the middle thirds of root canals in mandibular incisors. The preparation methods used were the reciprocating systems Reciproc (Group I and WaveOne (Group II and the oscillatory system Tilos (Group III. Comparisons were made by three-dimensional image reconstruction with cone-beam computed tomography before and after instrumentation. Changes in area, perimeter, centering ability, and pattern of preparation were analyzed. The results were subjected to ANOVA complemented by the Tukey’s test. Changes in area, perimeter, and tendency of transportation showed similar results among groups. The transportation index of the Tilos system was significantly lower than that of the other groups. Qualitative analysis of the preparation pattern showed that the Tilos system had a more uniform preparation, although Reciproc and WaveOne preparations appeared more rounded, incompatible with the original canal anatomy. There was similarity in the systems’ performance on flattened areas, although the Tilos system presented a better pattern of root canal preparation and a lower index of transportation.

  6. SOFTWARE TRAINING AIDS DEVELOPMENT AND IMPLEMENTATION IN PROFESSIONAL PREPARATION PRACTICE OF TECHNOLOGICAL EDUCATION TEACHER

    Directory of Open Access Journals (Sweden)

    Anatoliy G. Gritchenko

    2013-03-01

    Full Text Available The article outlines the theoretical and practical aspects of software training aids development and implementation in professional preparation practice of technological education teacher. The myriad opportunities of new information technologies are described; the characteristic features of modern software training tool (STT are revealed; the main algorithmic structure circuits of training programs construction (linear, cyclic, with hyperlinks, to the labels, which enable the development of STT variety and functionality are given; the methodology of STT creating is described based on the analysis of the technology teacher preparation in HEE content, MITE didactic functions and selection criteria of educational software for this area of specialist’s preparation.

  7. [Syntactic Processing in Broca's Area: Brodmann Areas 44 and 45].

    Science.gov (United States)

    Yamada, Atora; Sakai, Kuniyoshi L

    2017-04-01

    Brodmann areas 44 and 45 are known as Broca's area; however, their true functional roles are still unknown. Recent developments in neuroimaging techniques revealed the structures and functions of Broca's area in detail. More specifically regarding language functions, sufficient evidence has been accumulated that this region subserves the center of syntactic processing, not necessarily motor functions. Here, we review a role of Broca's area as the grammar center, including other roles in nonlinguistic functions.

  8. Rear Area Security In The Field Army Service Area.

    Science.gov (United States)

    2007-11-02

    his ma.jor subordinate Commanders, the arm support brigade commander. Rear are? ecurity doctrine requires the area coriander to coordin- ate unit...field army service area. Response The army support brigade coriander conducts phase I rear area security operations within the limits of current

  9. Environmental resources of selected areas of Hawaii: Ecological resources

    Energy Technology Data Exchange (ETDEWEB)

    Trettin, C.C.; Tolbert, V.R. [Oak Ridge National Lab., TN (United States). Environmental Sciences Div.; Jones, A.T. [Jones (Anthony T.), Vancouver, British Columbia (Canada); Smith, C.R. [Smith (Craig R.), Kailna, HI (United States); Kalmijn, A.J. [Kalmijn (Adrianus J.), Encinitas, CA (United States)

    1995-03-01

    This report has been prepared to make available and archive the background scientific data and related information collected on ecological resources during the preparation of the environmental impact statement (EIS) for Phases 3 and 4 of the Hawaii Geothermal Project (HGP) as defined by the state of Hawaii in its April 1989 proposal to Congress. Since the state of Hawaii is no longer pursuing or planning to pursue the HGP, DOE considers the project to be terminated. The background scientific data and related information presented in this report focus on several areas of Hawaii County. In this report, reference is made to these areas as study areas rather than as areas where proposed or alternative facilities of the HGP would be located. The resource areas addressed herein include terrestrial ecology, aquatic ecology, and marine ecology. The scientific background data and related information that were obtained from review of the (1) scientific literature, (2) government and private sector reports, (3) studies done under DOE interagency agreements with the US Fish and Wildlife Service (FWS) and with the US Army Corps of Engineers (COE), and (4) observations made during site visits are being made available for future research in these areas.

  10. Wetland Survey of Selected Areas in the Oak Ridge Y-12 Plant Area of Responsibilty, Oak Ridge, Tennessee

    Energy Technology Data Exchange (ETDEWEB)

    Rosensteel

    1997-01-01

    This document was prepared to summarize wetland surveys performed in the Y- 1 2 Plant area of responsibility in June and July 1994. Wetland surveys were conducted in three areas within the Oak Ridge Y- 12 Plant area of responsibility in June and July 1994: the Upper East Fork Poplar Creek (UEFPC) Operable Unit (OU), part of the Bear Creek Valley OU (the upper watershed of Bear Creek from the culvert under Bear Creek Road upstream through the Y-12 West End Environmental Management Area, and the catchment of Bear Creek North Tributary 1), and part of Chestnut Ridge OU 2 (the McCoy Branch area south of Bethel Valley Road). Using the criteria and methods set forth in the Wetlands Delineation Manual, 18 wetland areas were identified in the 3 areas surveyed; these areas were classified according to the system developed by Cowardin. Fourteen wetlands and one wetland/pond area that are associated with disturbed or remnant stream channels and seeps were identified in the UEFPC OU. Three wetlands were identified in the Bear Creek Valley OU portion of the survey area. One wetland was identified in the riparian zone of McCoy Branch in the southern portion of Chestnut Ridge OU 2.

  11. Recent RN graduate perceptions of educational preparation.

    Science.gov (United States)

    Candela, Lori; Bowles, Cheryl

    2008-01-01

    Nursing education programs strive to deliver curricula that prepare and transition graduates not just to survive but to truly thrive in any workplace environment. It is therefore important to reach out to those who have recently entered the nursing workforce to understand their views on educational preparation for practice. The purpose of this descriptive survey was to examine the perceptions of recent nurse graduates with regard to how well their educational programs prepared them for practice in their first jobs as registered nurses. Three hundred fifty-two nurses registered in the state of Nevada who graduated from a basic nursing program within the past five years completed the Survey of Nurses' Perceptions of Educational Preparation. Respondents perceived they were inadequately prepared in pharmacology, clinical practice, leadership/management, and the use of patient electronic medical records. In addition, respondents felt their programs prepared them more for success on the NCLEX-RN than for practice. Recommendations for addressing these issues are offered.

  12. The effects of speech motor preparation on auditory perception

    Science.gov (United States)

    Myers, John

    Perception and action are coupled via bidirectional relationships between sensory and motor systems. Motor systems influence sensory areas by imparting a feedforward influence on sensory processing termed "motor efference copy" (MEC). MEC is suggested to occur in humans because speech preparation and production modulate neural measures of auditory cortical activity. However, it is not known if MEC can affect auditory perception. We tested the hypothesis that during speech preparation auditory thresholds will increase relative to a control condition, and that the increase would be most evident for frequencies that match the upcoming vocal response. Participants performed trials in a speech condition that contained a visual cue indicating a vocal response to prepare (one of two frequencies), followed by a go signal to speak. To determine threshold shifts, voice-matched or -mismatched pure tones were presented at one of three time points between the cue and target. The control condition was the same except the visual cues did not specify a response and subjects did not speak. For each participant, we measured f0 thresholds in isolation from the task in order to establish baselines. Results indicated that auditory thresholds were highest during speech preparation, relative to baselines and a non-speech control condition, especially at suprathreshold levels. Thresholds for tones that matched the frequency of planned responses gradually increased over time, but sharply declined for the mismatched tones shortly before targets. Findings support the hypothesis that MEC influences auditory perception by modulating thresholds during speech preparation, with some specificity relative to the planned response. The threshold increase in tasks vs. baseline may reflect attentional demands of the tasks.

  13. METALLOGRAPHIC SAMPLE PREPARATION STATION-CONSTRUCTIVE CONCEPT

    Directory of Open Access Journals (Sweden)

    AVRAM Florin Timotei

    2016-11-01

    Full Text Available In this paper we propose to present the issues involved in the case of the constructive conception of a station for metallographic sample preparation. This station is destined for laboratory work. The metallographic station is composed of a robot ABB IRB1600, a metallographic microscope, a gripping device, a manipulator, a laboratory grinding and polishing machine. The robot will be used for manipulation of the sample preparation and the manipulator take the sample preparation for processing.

  14. Laboratory evaluation of commercial interferon preparations

    Energy Technology Data Exchange (ETDEWEB)

    Schoub, B.D.; Lyons, S.F.; Crespi, M.; Chiu, M.N. (University of the Witwatersrand, Johannesburg (South Africa). Dept. of Virology); Lomnitzer, R. (University of the Witwatersrand, Johannesburg (South Africa). Dept. of Immunology)

    1983-01-08

    The antiviral, antiproliferative and natural killer-cell (NKC) stimulatory activities of four commercial therapeutic interferon preparations were assayed in a laboratory. The antiviral and antiproliferative activities of each preparation were relatively similar, but an unexpectedly high NKC stimulatory activity was found in one of them. In-house determination of antiviral activity and evaluation of the antiproliferative and NKC stimulation potential of interferon preparations are essential before rational clinical trials of this agent are carried out.

  15. Cholera in Azov area

    Directory of Open Access Journals (Sweden)

    O. N. Domashenko

    2015-01-01

    Full Text Available The purpose of research is analysis of clinical course and treatment results of patients with cholera in the Azov area. Materials and methods. During the period from 29.05.2011 to 19.08.2011 33 cases of cholera (32 adults and 1 child and 25 vibrio carriers (22 adults and 3 children, which were caused by toxigenic strains of Vibrio cholera El Tor serogroup O1 Ogawa. Results. Likely factors of disease transmission in Mariupol are sea and river water, and the fish that were caught in the waters of the city. Typical and watery diarrhoea, vomiting, abdominal pain and lack of normal body temperature, dehydration syndrome, characterized clinical cholera for adults in most cases. The mean duration of diarrhoea was 6,6 days. At 46.9% observed atypical symptoms in 10 (31,3% – abdominal pain (1 patient cramping in 7 cases, localized in the epigastria region, at 2-over stomach. In 5 patients (15,6% had an increase in body temperature to 37,2–37,7 degrees Celsius. In 15 (46,9% patients had severe nausea accompanied by vomiting. Easy for cholera was observed in 1 (3.1%, moderate – in 14 (43,8%, heavy – in 17 (53,1% patients. Dehydration I level is set at 4 (12,5%, II – from 6 (18,7%, III – in 18 (56,3%, IV – 4 (12,5% patients. Cholera outbreak was characterized by a predominance of severe disease and severe dehydration (III and IV, which was observed in 68.8% of patients. The decisive factor in the treatment of cholera patients was initiated in a timely manner rehydration therapy, in particular the introduction of the solution «Trisol». Against the background of rehydration therapy hyperkalaemia was observed in 9,4% of cases, vascular rehydration at 9,4%, the cell rehydration in 3,1% of patients. Fatal accidents cholera outbreaks have not been observed. Conclusion. Clinical diagnosis of cholera and the provision of medical care in the prehospital phase were poor, indicating the need for systematic conducting training seminars among experts

  16. Manganese Dioxide with High Specific Surface Area for Alkaline Battery

    Institute of Scientific and Technical Information of China (English)

    HUANG You-ju; LIN Yu-li; LI Wei-shan

    2012-01-01

    The authors reported a facile method for the synthesis of manganese dioxide without any template and catalyst at a low-temperature.The prepared sample was characterized with X-ray diffraction(XRD),scanning electron microscopy(SEM),Brunauer-Emmett-Teller(BET) surface analysis,Fourier transform infrared(FTIR) spectrometry,cyclic voltammetry,altemative current(AC) impedance test and battery discharge test.It is found that the prepared sample belongs to α-MnO2 and has a microsphere morphology and a large BET surface area.The electrochemical characterization indicates that the prepared sample displays a larger electrochemical capacitance than the commercial electrolytic manganese dioxides(EMD) in Na2SO4 solution,and exhibits larger discharge capacity than EMD,especially at a high rate discharge condition when it is used as cathode of alkaline Zn/MnO2 battery.

  17. Dynamized Preparations in Cell Culture

    Directory of Open Access Journals (Sweden)

    Ellanzhiyil Surendran Sunila

    2009-01-01

    Full Text Available Although reports on the efficacy of homeopathic medicines in animal models are limited, there are even fewer reports on the in vitro action of these dynamized preparations. We have evaluated the cytotoxic activity of 30C and 200C potencies of ten dynamized medicines against Dalton's Lymphoma Ascites, Ehrlich's Ascites Carcinoma, lung fibroblast (L929 and Chinese Hamster Ovary (CHO cell lines and compared activity with their mother tinctures during short-term and long-term cell culture. The effect of dynamized medicines to induce apoptosis was also evaluated and we studied how dynamized medicines affected genes expressed during apoptosis. Mother tinctures as well as some dynamized medicines showed significant cytotoxicity to cells during short and long-term incubation. Potentiated alcohol control did not produce any cytotoxicity at concentrations studied. The dynamized medicines were found to inhibit CHO cell colony formation and thymidine uptake in L929 cells and those of Thuja, Hydrastis and Carcinosinum were found to induce apoptosis in DLA cells. Moreover, dynamized Carcinosinum was found to induce the expression of p53 while dynamized Thuja produced characteristic laddering pattern in agarose gel electrophoresis of DNA. These results indicate that dynamized medicines possess cytotoxic as well as apoptosis-inducing properties.

  18. LHC Report: Restart preparations continue

    CERN Multimedia

    Katy Foraz for the LHC team and Julia Trummer for the RP Group

    2012-01-01

    Maintenance and consolidation work has been progressing well in both the machine and the experiments in preparation for the March restart.   A sample material is attached to the LHC (the white bag taped to the green line), to measure the radiation doses. Additional work was required around Point 5 due to the discovery and repair of a problem with the RF fingers at the connection of two beam vacuum chambers in CMS. The repair has been completed successfully and the sector is now under vacuum. In order to avoid rushing the delicate final operations required for closing the detector, the restart of the machine has been postponed by one week, from 7 March to 14 March. In the machine, the first cool-down to 1.9 K has started in several sectors ,and the cool-down of the whole machine is still planned to be finished by 21 February. The time window between 22 February and 14 March will be dedicated to powering and cryogenic tests. Since 12 December, the Radiation Protection (RP) group has been deep...

  19. CMS prepares for new challenges

    CERN Multimedia

    Antonella Del Rosso

    2014-01-01

    One of the world’s largest physics experiments has just had a change in leadership. This is a chance for the collaboration to take stock of the tremendous work done for LS1 and to prepare for the challenges that lie ahead.   From left to right: Kerstin Borras, Tiziano Camporesi and Paris Sphicas. “The keyword is teamwork. That’s the only way you can effectively manage a large number of extremely talented and motivated people,” says Tiziano Camporesi who took the reins of the CMS collaboration at the beginning of the year. The recipe might seem easier on paper than in practice. However, given his 28 years at CERN, two of which he spent as the head of the DELPHI collaboration, Camporesi has extensive experience in managing large scientific collaborations and success in this respect is well within his reach: “I have learned many lessons from the past and I believe that building consensus is instrumental to successful leadership.” The C...

  20. Preparing Citizens for the Future

    Science.gov (United States)

    Kubinec, W.

    1995-05-01

    Introductory astronomy courses are heavily utilized by non-science majors to check off a general degree requirement in science. For a large portion of this population, this course will be their only academic encounter with science. Many of these students have not had successful preparatory experiences. Some individuals exhibit a math/science learned helplessness. These facts coupled with the need for science literacy are proper concerns in designing the educational experience called introductory astronomy. My course has been converted largely to a collaborative environment. A unique feature is an emphasis on science policy and the utilization of structured controversy. I use lecture and some video excerpts to introduce science policy and strategic planning. A specific controversial policy related to astronomy is posed. The students prepare pro and con arguments, debate the issue formally in class and engage in small-group discussions to discover common values and solutions. Personal beliefs and the views of various majors provide fuel for lively discourse. Structured controversy develops social responsibility, intellectual competence, conflict resolution skills and personal confidence. These attributes are essential for the techno-political future.

  1. [Bioequivalence studies of pharmaceutical preparations].

    Science.gov (United States)

    Vetchý, D; Frýbortová, K; Rabisková, M; Danecková, H

    2007-01-01

    Bioequivalence studies are very important for the development of a pharmaceutical preparation in the pharmaceutical industry. Their rationale is the monitoring of pharmacokinetic and pharmacodynamic parameters after the administration of tested drugs. The target of such study is to evaluate the therapeutic compatibility of tested drugs (pharmaceutical equivalents or pharmaceutical alternatives). The importance of bioequivalence studies is increasing also due to the large growth of the production and consumption of generic products. Generic products represent approximately 50 % of the whole consumption in many European countries and USA. The search output of bioequivalence study is together with the pharmaceutical quality data of medical product one of the main part of the registration file submitted to a national regulatory authorities. The registration of generic products does not demand complicated and expensive clinical study contrary to original product. The comparison of the original and the generic product via bioequivalence study is suggested as sufficient. The aim of this article is to provide to a medical public a summary about the types of bioequivalence studies, their range, rules of their practise and let them gain their own attitude to this question.

  2. Personality Development during Teacher Preparation

    Science.gov (United States)

    Corcoran, Roisin P.; O’Flaherty, Joanne

    2016-01-01

    Objective: The purpose of this 3-year longitudinal study was to examine pre-service teachers’ personality trajectories as measured by the IPIP Big-Five factor markers during teacher preparation. The relationship between students’ personality traits, social desirability, and prior academic attainment was also examined. Method: This 3-year longitudinal study invited participants from the first year of a 4-year undergraduate (UG) pre-service teacher education program, the class of 2017. The sample consisted of 305 students. Results: The results suggest that extraversion, agreeableness, conscientiousness, emotional stability, and openness to experience were best represented by a non-significant longitudinal change in means. Results also suggest that social desirability predicts agreeableness and emotional stability with small to moderate effect sizes. Conclusion: The study concludes that no value is added to pre-service teachers’ personality traits during 3 years of tertiary education. Furthermore, the data presented does not support the view that academic attainment is a good predictor of personality traits. Implications for educational research, theory, and practice are considered. PMID:27877143

  3. Electrocatalysts Prepared by Galvanic Replacement

    Directory of Open Access Journals (Sweden)

    Athanasios Papaderakis

    2017-03-01

    Full Text Available Galvanic replacement is the spontaneous replacement of surface layers of a metal, M, by a more noble metal, Mnoble, when the former is treated with a solution containing the latter in ionic form, according to the general replacement reaction: nM + mMnoblen+ → nMm+ + mMnoble. The reaction is driven by the difference in the equilibrium potential of the two metal/metal ion redox couples and, to avoid parasitic cathodic processes such as oxygen reduction and (in some cases hydrogen evolution too, both oxygen levels and the pH must be optimized. The resulting bimetallic material can in principle have a Mnoble-rich shell and M-rich core (denoted as Mnoble(M leading to a possible decrease in noble metal loading and the modification of its properties by the underlying metal M. This paper reviews a number of bimetallic or ternary electrocatalytic materials prepared by galvanic replacement for fuel cell, electrolysis and electrosynthesis reactions. These include oxygen reduction, methanol, formic acid and ethanol oxidation, hydrogen evolution and oxidation, oxygen evolution, borohydride oxidation, and halide reduction. Methods for depositing the precursor metal M on the support material (electrodeposition, electroless deposition, photodeposition as well as the various options for the support are also reviewed.

  4. Fuels Preparation Department monthly report, January 1958

    Energy Technology Data Exchange (ETDEWEB)

    1958-02-28

    This report describes the operation of the fuels preparation department for the month of January, 1958. Manufacturing, employee relations, process development, plant improvements, and financial operations are described.

  5. Fuels Preparation Department monthly report, October 1960

    Energy Technology Data Exchange (ETDEWEB)

    1960-11-07

    This report describes the operation of the fuels preparation department for the month of October, 1960. Manufacturing, process development, employee relations, financial operations, and plant improvements are discussed.

  6. Preparation of some compounded soup powders

    Directory of Open Access Journals (Sweden)

    B. S. Bhatia

    1961-01-01

    Full Text Available Recipes for the preparation of some compounded soup powders from tomatoes, potatoes, carrots, green peas, dried peas, chicken and mutton using components like corn starch, skim milk powder, hydrogenated groundnut oil, common salt, mixed spices (black pepper, caraway and ginger and monosodium glutamate have been developed. Pretreatment and drying conditions for the preparation of pre-cooked dry bases from tomatoes, potatoes, carrots, green peas, dried peas, chicken and mutton have been determined. Except for tomatoes where vacuum drier is necessary, other bases can be easily prepared in a simple cross flow hot air cabinet drier and used subsequently in the preparation of soup powders.

  7. STRUCTURAL ANALYSIS OF CONDITIONAL PREPARATION IN JUDO

    Directory of Open Access Journals (Sweden)

    Slavko Obadov

    2006-06-01

    Full Text Available Conditional preparation is a constituent part of overall sports preparation. Conditional training might be defined as a process of improvement of a sportsman’s functional and motor abilities, morphological characteristics, health, as well as the required motor knowledge. Conditional preparation can be might be classified as: general, basic and situational conditional preparation. Programs of the conditional training might be classified as: developing, resuming, recovering, preventive and recovering ones. High level of the general physical preparation enables maximum demonstration of the physical abilities of a sportsman during the stage of improvement of the specific motor abilities. Good general preparation of a sportsman enables him to push beyond his functional limits in order to cope with heavy loads easier, which subsequently enables him to achieve top performance level. Basic conditional preparation assumes the development of the most important judo abilities. Specific conditional preparation is related directly to the execution of different structural elements under the conditional requirements. Situational conditional preparation enables integration of the tactical and conditional training.

  8. Catch-In-Areas Main

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Catch-In-Areas database integrates catch data from the Catch Accounting System (which has the spatial resolution of a NMFS Reporting Area) into a database that...

  9. Major Land Resource Areas (MLRA)

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This is a polygon coverage of the Land Resource Regions and Major Land Resource Areas of the conterminous United States. Land resource regions are geographic areas...

  10. World Area Forecast System (WAFS)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The World Area Forecast System (WAFS) is a worldwide system by which world area forecast centers provide aeronautical meteorological en-route forecasts in uniform...

  11. Catchment areas for public transport

    DEFF Research Database (Denmark)

    Andersen, Jonas Lohmann Elkjær; Landex, Alex

    2008-01-01

    In the planning of public transport catchment areas of stops are often included to estimate potential number of travellers. There are different approaches to GIS-based catchment area analyses depending on the desired level of detail. The Circular Buffer approach is the fundamental, but also...... between the Circular Buffer approach and the Service Area approach are illustrated and a comparison between the sizes of the catchment areas is made. The strength of the Service Area approach and the impact on the catchment area when adding additional time resistance to crossing of stairways...... is illustrated by a case example. Furthermore, a case example illustrates how the additional time resistance in stairways affects the catchment area of an underground station compared to a ground-level station. It is also illustrated how catchment area analyses can serve in the planning of stops on a new line...

  12. Laguna Atascosa Wilderness study area

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This document is a brief report on a wilderness study area located in the Laguna Atascosa National Wildlife Refuge. It discusses the history of the study area, its...

  13. Special Protection Area Review Data

    Data.gov (United States)

    Montgomery County of Maryland — A Special Protection Area (SPA) is a geographic area designated by the County Council which has high quality or unusually sensitive water resources and environmental...

  14. Facial Areas and Emotional Information

    Science.gov (United States)

    Boucher, Jerry D.; Ekman, Paul

    1975-01-01

    Provides strong support for the view that there is no one area of the face which best reveals emotion, but that the value of the different facial areas in distinguishing emotions depends upon the emotion being judged. (Author)

  15. Facial Areas and Emotional Information

    Science.gov (United States)

    Boucher, Jerry D.; Ekman, Paul

    1975-01-01

    Provides strong support for the view that there is no one area of the face which best reveals emotion, but that the value of the different facial areas in distinguishing emotions depends upon the emotion being judged. (Author)

  16. VT - Vermont Rational Service Areas

    Data.gov (United States)

    Vermont Center for Geographic Information — Data Layer Name: Vermont Rational Service Areas (RSAs)Alternate Name: Vermont RSAsOverview:Rational Service Areas (RSAs), originally developed in 2001 and revised in...

  17. Motor preparation attenuates neural variability and beta-band LFP in parietal cortex.

    Science.gov (United States)

    Chen, Mo; Wei, Linyu; Liu, Yu

    2014-10-28

    Accumulative evidence shows that neural variability is meaningful and powerful during brain information processing, but how cognitive state influences neural variability is still unclear. We studied neural variability during motor preparation in lateral intraparietal area (LIP), a brain area closely involved in saccade generation. During motor preparation, we observed significant variability decline, and the decline highly correlated with beta-band local field potential (LFP) fluctuations. Furthermore, we found similar variance-LFP correlations in both the memory-guided saccade task and the visually-guided saccade task. These results indicate a possible linkage between beta-band LFP and trial-to-trial neural variability.

  18. FUDNAMENTAL NOTE OF THE MOTRICAL EDUCATION AREA

    Directory of Open Access Journals (Sweden)

    Dragnea Adrian

    2009-03-01

    Full Text Available The appearance of sport as an entertainment and Physical Education means, a factor which is part of the military groups as well as that of the pupils that have physical exercise as common instrument, led to the appearance of the already know term: “Physical Education and Sport”, which has constituted the area of the university preparation for many years now.With direct reference to the last denominations, one can say that for the last three decades no differentiationwas made between the area and the profile, the Physical Education and Sport representing both of these.A gathering of the terms inside this area and throughout different countries underlines a variety of termsinfluenced by numerous factors which belong mostly to the scientific orientation of those who proposed them.Thus, many names of the area appeared and among these one may count the following: Physical Education,Physical Culture, Physical Culture and Sport, Physical Education and Sport, The Sport Sciences, the Science ofPhysical Education and Sport, the Science of the Body Activities, the Science of the Motric Activities, TheScience of the Physical Activities and Sport, the Motricity Sciences, the Physical Education and Kinesiology,Kinathropology, Motrical Anthropology. This diversity of the names of the motricity research field led to asmany conceptions, which mostly targeted part of the area, the global approaches being very rare and notaccepted from various reasons. This led to an identity crisis (which until recently also characterized some othersciences about man further accentuated by the motric activities expansion in the contemporary society.From the ones presented above, some conclusions are to be drawn:athe analyzed area is real, without being precisely delimited as denomination on the one side, due to theproliferation of the forms of motric activity (the appearance of new sports, new structures of a formingeducationalcharacter and on the other hand due to the lack

  19. Suburban areas and urban life

    DEFF Research Database (Denmark)

    Melgaard, Bente

    which forms of ‘urban life’ are suitable for the suburbs and discusses which urban life activities are resilient in the suburbs. What do the residents of respectively single-family housing areas and social housing areas want? Does the idea of vibrant urban qualities in suburban areas, that today...

  20. Preparing for your annual staff appraisal: part 2.

    Science.gov (United States)

    Price, B

    Annual appraisals are part of performance management and are designed to motivate, develop and support employees in performing their roles to the highest possible standard. They provide an opportunity for constructive discussion of performance, identification of areas for development and agreement of approaches by which employees needs could be met. Part 1 of this article was concerned with preparation of the employee and manager for annual staff appraisal. This article provides advice for managers who perform annual appraisal interviews. Guidance is offered on how to ensure the strategic objectives of the team and healthcare organisation are met, a balanced understanding of nurse performance is achieved, and future objectives are identified and agreed

  1. Preparation and characterization of 125 I labeled bovine serum albumin

    Directory of Open Access Journals (Sweden)

    K S Ashwitha Rai

    2015-01-01

    Full Text Available Bovine serum albumin is a model protein, which has been conventionally used as protein standard and in many areas of biochemistry, pharmacology and medicine. Radioiodination procedure for bovine serum albumin employing chloramine-T as an oxidant with slight modification was evaluated critically to establish the optimal conditions for the preparation of radiolabeled tracer ( 125 I-BSA with required specific activity without impairing the immune reactivity and biological activity. Optimized radioiodination procedure involving 10 µg of chloramine-T along with 20 µg of sodium metabisulphite with 60 seconds incubation at 2° yielded 125 I-BSA with high integrity.

  2. Preparation and Electrochemical Properties of Porous Platinum Electrode

    Institute of Scientific and Technical Information of China (English)

    HE Xin; CHEN Boxun; CHEN Qiao

    2012-01-01

    Porous platinum electrodes were prepared by adding YSZ,as an active material,in platinum paste.Relationship between microstructure and electrochemical performance of O2(g),Pt/YSZ electrode have been characterized by SEM and cyclic voltammetry.Results showed that the microstructure of platinum electrode is a significant impact on the cyclic voltammetry.With the increase of platinum electrode's porosity,the area of three-phase boundary of O2(g)/Pt/YSZ was increased.The electrochemical reactivity was also enhanced.These were presented as the increase of current density and cathode voltage in cyclic voltammetry.

  3. A Novel Method to Prepare Potassium Sodium Titanate Nanotubes

    Institute of Scientific and Technical Information of China (English)

    Xiao Dong WANG; Zhen Sheng JIN; Xian Ru PEI; Jian Jun YANG; Zhi Jun ZHANG

    2006-01-01

    A novel method, i.e. molten salt method, was adopted to prepare potassium sodium titanate nanotubes. EDX results indicated that the ion-exchange reaction reached an equilibrium state at around 9 h. The 24 h ion-exchanged product maintained nano-tubular and its crystalline structure was consistent with that of Na2Ti2O4(OH)2 nanotubes. The nanotubes have a high specific surface area, possibly making this material a good candidate as controlled release materials,catalyst, electrode materials, etc..

  4. Preparation of activated carbons from Chinese coal and hydrolysis lignin

    Energy Technology Data Exchange (ETDEWEB)

    Zou, Y.; Han, B.X. [Tuskegee University, Tuskegee, AL (USA). School of Engineering, Dept. of Chemical Engineering

    2001-07-01

    Activated carbons from Chinese coal and Chinese hydrolysis lignin have been prepared by chemical activation with potassium hydroxide. The following aspects of these activated materials have been analyzed: raw material; pre-treatment of raw material; activation agent, activation temperature and time, acid the activation agent/raw material ratio. Activated carbons with BET specific surface areas of the order of 2400-2600 m{sup 2}/g which exhibited substantial microporosity, a total pore volume of over 1.30 cm{sup 3}/g and a Methylene Blue adsorption capacity of over 440 mg/g were obtained.

  5. Preparation of Nd-doped barium cerate through different routes

    DEFF Research Database (Denmark)

    Chen, F.L.; Toft Sørensen, O.; Meng, G.Y.;

    1997-01-01

    BaCe0.9Nd0.1O3-delta was prepared through different routes: oxalate coprecipitation (OF), carbonate-oxide mixed by ball-milling (COB) and carbonate-oxide mixed by mortar/pestle (COM). The reaction process studied by DTA-TG and XRD showed that calcination of the precursor powders at T greater than...... density and open porosity indicated that the calcination temperature had a major influence on the sintering process for all the three routes. The calcined powders from OP and COB had small particle size, large surface area and good sinterability, while those from COM had large particle size, small surface...

  6. Study on the preparation and properties of ultrafine copper powder

    Institute of Scientific and Technical Information of China (English)

    LIU; Wei-ping; HUANG; Lin; YIN; Yan-hong

    2005-01-01

    In the study, the common copper powder is used as sample, the ultrafine copper powder is researched by a new process of high energy ball milling. The influence of the milling time, the milling intensity, the milling medium, the ratio of hall to material, the dry milling and the wet milling on copper powder size are studied and the rule of every factors influencing properties of copper particle size and specific surface area under the best experimental conditions are acquired. By the regressive analysis of experimental results under the best conditions, the characteristic equation of copper particle prepared by high energy milling is confirmed.

  7. Preparation and characterization of mesoporous tetragonal sulfated zirconia

    Institute of Scientific and Technical Information of China (English)

    Chun Xia He; Bin Yue; Ji Fang Cheng; Wei Ming Hua; Ying Hong Yue; He Yong He

    2009-01-01

    Mesoporous tetragonal sulfated zirconia with high surface area and narrow pore-size distribution was prepared using Zr(O-nPr)4 as zirconium precursor, sulfuric acid as sulfur source and triblock copolymer poly(ethylene glycol)-poly(propylene glycol)poly(ethylene glycol) (P123) as the template. The samples were characterized by X-ray diffraction, N2 sorption, TEM, and NH3TPD. A phase transformation from monoclinic sulfated zirconia to tetragonal sulfated zirconia is observed. The product shows strong acidity.

  8. Preparation of Functional Polymeric Microspheres

    Institute of Scientific and Technical Information of China (English)

    Changchun Wang; Yonghui Deng; Wuli Yang; Shoukuang Fu

    2005-01-01

    @@ 1Introduction Because of the wide applications in the area of biomedical and biotechnological fields, a great efforts have been done to fabricate different kinds of microspheres with tailored structural and surface properties over the last decade[1]. Among them, stimuli responsive microspheres are microspheres that show ability to change their physical-chemical properties and colloidal properties in response to environmental stimuli such as changes of temperature, pH, chemicals, light, electrical field, magnetic field or mechanic stress, etc. These microspheres have been under intensive study for their high potential applications in biomedical and biotechnological fields such as controlled drug delivery[2], biosensor[3], chemical isolation[4], cell culture substrates[5], enzyme immobilization[6], bioelectrocatalysis[7], and magnetically controlled electrochemical reaction[8]. However,most of the reported stimuli responsive microspheres only show response to one specific stimulus. Up to now,to the best of our knowledge, only a few works have been directed to the fabrication of microspheres which show response to more than one stimulus[9]. In this paper, a system synthesis method for stimuli responsive microspheres with more useful properties was reported, and the simple application in biomedical area have been mentioned.

  9. Freihoelser Forst Local Training Area rehabilitation project

    Energy Technology Data Exchange (ETDEWEB)

    Hinchman, R.R.; Zellmer, S.D.; Johnson, D.O.; Severinghaus, W.D.; Brent, J.J. (Army Construction Engineering Research Lab., Champaign, IL (United States). Environmental Div.)

    1991-12-01

    Intensive and continued use of the Freihoelser Forst Local Training Area (LTA) for military training activities had resulted in serious environmental problems, exemplified by a lack of vegetative cover and severe erosion by water and wind. The project's goal was to develop and demonstrate rapid, cost-effective methods to stabilize the LTA's barren, eroding maneuver areas and make training conditions more realistic. The major factors limiting rehabilitation efforts were the sandy, infertile, and acidic soils. The project was conducted in two phases. Phase I demonstrated and evaluated three separate rehabilitation treatments ranging in cost from moderate to expensive. Each treatment used a different type of soil amendment (fertilizer and straw, compost, or chicken manure), but all used identical seedbed preparation methods and seed mixtures. Phase I was conducted on relatively small replicated plots and was monitored three times during each growing season. All three treatments satisfactorily reestablished vegetation and controlled erosion. Because of their small size, the Phase I demonstration plots had only a minor stabilizing effect on the erosion problems of the LTA as a whole. The Phase II treatment was based on lessons teamed from Phase I and from other revegetation projects in Germany. Phase II revegetated a large area of the LTA, which included nearly all of the most severely disturbed land. Phase II, which was monitored in the same way as Phase I but for a shorter period of time, was highly successful in stabilizing most areas treated. The revegetation plant community was dominated by native grasses and legumes that stabilized the loose, sandy soils and improved the training realism of a major portion of the LTA.

  10. High-surface-area silica nanospheres (KCC-1) with a fibrous morphology

    KAUST Repository

    Polshettiwar, Vivek

    2010-08-02

    Fibrous nanosilica: A new family of high-surface-area silica nanospheres (KCC-1) have been prepared (see picture). KCC-1 features excellent physical properties, including high surface area, unprecedented fibrous surface morphology, high thermal (up to 950 °C) and hydrothermal stabilities, and high mechanical stability. Copyright © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Public space in the housing estates of Poznan metropolitan area: design strategy

    OpenAIRE

    2015-01-01

    The article was prepared on the basis of research conducted at the Faculty of Architecture at Poznan University of Technology. It constitutes an introduction to the subject of regeneration of housing areas in the Poznan Municipal Area in order to familiarize the reader with the method of socio-spatial analysis in relation to public space in housing estates.

  12. 9 CFR 318.304 - Operations in the thermal processing area.

    Science.gov (United States)

    2010-01-01

    ... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Operations in the thermal processing area. 318.304 Section 318.304 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE... PREPARATION OF PRODUCTS Canning and Canned Products § 318.304 Operations in the thermal processing area....

  13. Preparation of nanocrystalline MgO by surfactant assisted precipitation method

    Energy Technology Data Exchange (ETDEWEB)

    Rezaei, Mehran, E-mail: rezaei@kashanu.ac.ir [Catalyst and Advanced Materials Research Laboratory, Chemical Engineering Department, Faculty of Engineering, University of Kashan, Kashan (Iran, Islamic Republic of); Institute of Nanoscience and Nanotechnology, University of Kashan, Kashan (Iran, Islamic Republic of); Khajenoori, Majid; Nematollahi, Behzad [Catalyst and Advanced Materials Research Laboratory, Chemical Engineering Department, Faculty of Engineering, University of Kashan, Kashan (Iran, Islamic Republic of)

    2011-10-15

    Highlights: {yields} Nanocrystalline magnesium oxide with high surface area. {yields} MgO prepared with surfactant showed different morphologies compared with the sample prepared without surfactant. {yields} MgO prepared with surfactant showed a plate-like shape. {yields} Refluxing temperature and time and the surfactant to metal molar ratio affect the textural properties of MgO. -- Abstract: Nanocrystalline magnesium oxide with high surface area was prepared by a simple precipitation method using pluronic P123 triblock copolymer (Poly (ethylene glycol)-block, Poly (propylene glycol)-block, Poly (ethylene glycol)) as surfactant and under refluxing conditions. The prepared samples were characterized by X-ray diffraction (XRD), N{sub 2} adsorption (BET) and scanning and transmission electron microscopies (SEM and TEM). The obtained results revealed that the refluxing time and temperature and the molar ratio of surfactant to metal affect the structural properties of MgO, because of the changes in the rate and extent of P123 adsorption on the prepared samples. The results showed that the addition of surfactant is effective to prepare magnesium oxide with high surface area and affects the morphology of the prepared samples. With increasing the P123/MgO molar ratio to 0.05 the pore size distribution was shifted to larger size. The sample prepared with addition of surfactant showed a plate-like shape which was completely different with the morphology of the sample prepared without surfactant. The formation of nanoplate-like MgO was related to higher surface density of Mg ions on the (0 0 1) plane than that on the other planes of the Mg(OH){sub 2} crystal. The (0 0 1) plane would be blocked preferentially by the adsorbed P123 molecules during the growing process of Mg(OH){sub 2} nanoentities and the growth on the (0 0 1) plane would be markedly restricted, and the consequence is the generation of nanoplate-like MgO. In addition, increase in refluxing temperature and time

  14. MPLS for metropolitan area networks

    CERN Document Server

    Tan, Nam-Kee

    2004-01-01

    METROPOLITAN AREA NETWORKS AND MPLSRequirements of Metropolitan Area Network ServicesMetropolitan Area Network OverviewThe Bandwidth DemandThe Metro Service Provider's Business ApproachesThe Emerging Metro Customer Expectations and NeedsSome Prevailing Metro Service OpportunitiesService Aspects and RequirementsRoles of MPLS in Metropolitan Area NetworksMPLS PrimerMPLS ApplicationsTRAFFIC ENGINEERING ASPECTS OF METROPOLITAN AREA NETWORKSTraffic Engineering ConceptsNetwork CongestionHyper Aggregation ProblemEasing CongestionNetwork ControlTactical versus Strategic Traffic EngineeringIP/ATM Overl

  15. Pathfinder - flight preparation on lakebed

    Science.gov (United States)

    1995-01-01

    AeroVironment, Inc., crew members prepare the Pathfinder solar-powered aircraft for its first flight on Rogers Dry Lake at NASA's Dryden Flight Research Center, Edwards, California, after its configuration was shanged from 8 electric motors to 6. Bob Curtin of AeroVironment is in the foreground of the photo. Pathfinder was a lightweight, solar-powered, remotely piloted flying wing aircraft used to demonstrate the use of solar power for long-duration, high-altitude flight. Its name denotes its mission as the 'Pathfinder' or first in a series of solar-powered aircraft that will be able to remain airborne for weeks or months on scientific sampling and imaging missions. Solar arrays covered most of the upper wing surface of the Pathfinder aircraft. These arrays provided up to 8,000 watts of power at high noon on a clear summer day. That power fed the aircraft's six electric motors as well as its avionics, communications, and other electrical systems. Pathfinder also had a backup battery system that could provide power for two to five hours, allowing for limited-duration flight after dark. Pathfinder flew at airspeeds of only 15 to 20 mph. Pitch control was maintained by using tiny elevators on the trailing edge of the wing while turns and yaw control were accomplished by slowing down or speeding up the motors on the outboard sections of the wing. On September 11, 1995, Pathfinder set a new altitude record for solar-powered aircraft of 50,567 feet above Edwards Air Force Base, California, on a 12-hour flight. On July 7, 1997, it set another, unofficial record of 71,500 feet at the Pacific Missile Range Facility, Kauai, Hawaii. In 1998, Pathfinder was modified into the longer-winged Pathfinder Plus configuration. (See the Pathfinder Plus photos and project description.)

  16. STRAWBERRY CRATER ROADLESS AREAS, ARIZONA.

    Science.gov (United States)

    Wolfe, Edward W.; Light, Thomas D.

    1984-01-01

    The results of a mineral survey conducted in the Strawberry Crater Roadless Areas, Arizona, indicate little promise for the occurrence of metallic mineral or fossil fuel resources in the area. The area contains deposits of cinder, useful for the production of aggregate block, and for deposits of decorative stone; however, similar deposits occur in great abundance throughout the San Francisco volcanic field outside the roadless areas. There is a possibility that the Strawberry Crater Roadless Areas may overlie part of a crustal magma chamber or still warm pluton related to the San Francisco Mountain stratovolcano or to basaltic vents of late Pleistocene or Holocene age. Such a magma chamber or pluton beneath the Strawberry Crater Roadless Areas might be an energy source from which a hot-, dry-rock geothermal energy system could be developed, and a probable geothermal resource potential is therefore assigned to these areas. 9 refs.

  17. Fractal cartography of urban areas.

    Science.gov (United States)

    Encarnação, Sara; Gaudiano, Marcos; Santos, Francisco C; Tenedório, José A; Pacheco, Jorge M

    2012-01-01

    In a world in which the pace of cities is increasing, prompt access to relevant information is crucial to the understanding and regulation of land use and its evolution in time. In spite of this, characterization and regulation of urban areas remains a complex process, requiring expert human intervention, analysis and judgment. Here we carry out a spatio-temporal fractal analysis of a metropolitan area, based on which we develop a model which generates a cartographic representation and classification of built-up areas, identifying (and even predicting) those areas requiring the most proximate planning and regulation. Furthermore, we show how different types of urban areas identified by the model co-evolve with the city, requiring policy regulation to be flexible and adaptive, acting just in time. The algorithmic implementation of the model is applicable to any built-up area and simple enough to pave the way for the automatic classification of urban areas worldwide.

  18. Large-mode-area leaky optical fibre fabricated by MCVD

    OpenAIRE

    Dussardier, Bernard; Trzesien, Stanislaw; Ude, Michèle; Rastogi, Vipul; Kumar, Ajeet; Monnom, Gérard

    2008-01-01

    International audience; A large mode area single-mode optical fibre based on leaky mode filtering was prepared by MCVD. The cladding structure discriminates the fundamental mode from the higher order ones. A preliminary version has 25-µm core diameter and 0.11 numerical aperture. A Gaussian-like mode with 22-µm MFD is observed after 3-m propagation, in agreement with modeling.

  19. Content Area Reading: Principles and Strategies to Promote Independent Learning

    Directory of Open Access Journals (Sweden)

    Bachrudin Musthafa

    1997-01-01

    Full Text Available Abstract: Since the formal education cannot be expected to provide individuals with sufficient knowledge to last a lifetime, educators need to help learners develop knowledge, skills, and predispositions essential for independent learning. Reading in content areas whose primary purpose is to help learners acquire content literacy or the ability to use reading (and writing for the acquisition of new knowledge from materials required in their subject is one way of preparing students to be independent learners.

  20. HOW TO RESTORE SOIL FUNCTIONALITY IN DEGRADED AREAS OF VINEYARDS

    OpenAIRE

    E. A. C. Costantini; Priori, S; Fantappiè, M

    2016-01-01

    In both conventional and organic vineyards, it is quite common to have areas characterized by problems in vine health, grape production and quality, often caused by improper land preparation before vine plantation and/or management. Causes for soil malfunctioning can include: reduced contribution of the soil fauna to the ecosystem services (i.e. nutrient cycles), poor organic matter content, imbalance of some element ratio, altered pH, water deficiency, soil compaction and/or scarce oxygenati...

  1. Preparing and correcting extracted BRITE observations

    CERN Document Server

    Buysschaert, B; Neiner, C

    2016-01-01

    Extracted BRITE lightcurves must be carefully prepared and corrected for instrumental effects before a scientific analysis can be performed. Therefore, we have created a suite of Python routines to prepare and correct the lightcurves, which is publicly available. In this paper we describe the method and successive steps performed by these routines.

  2. Effective Preparation Program Features: A Literature Review

    Science.gov (United States)

    Crow, Gary M.; Whiteman, Rodney S.

    2016-01-01

    This article is a summary of a report prepared for the University Council for Educational Administration Program Improvement Project for the Wallace Foundation. This explores the research base for educational leadership preparation programs, specifically examining literature on program features. The review covers context, candidates, faculty,…

  3. Praxis and Poiesis in Piano Repertoire Preparation

    Science.gov (United States)

    Dos Santos, Regina Antunes Teixeira; Hentschke, Liane

    2011-01-01

    The piano repertoire preparation of three undergraduate students at three different academic levels--the first, fifth and eighth semesters--was followed during an academic semester. A phenomenological approach was used to collect data in three stages: an introductory interview, observations of the repertoire under preparation and a final…

  4. The Preparation of Human Service Professionals.

    Science.gov (United States)

    Gartner, Alan

    New forms of preparing workers in the human services have the potential of changing and improving those services. A central feature of the new forms of preparation is that they must both be preparatory for the services and be characteristic of them (for example, if the services are participatory in nature, the training should also be so). There is…

  5. Substrate preparation by contactless mechanochemical polish

    Science.gov (United States)

    Rotter, S.; Lachish, U.; El-Hanany, U.

    1985-10-01

    A simple, yet effective, polishing technique for substrate preparation is presented. It is contactless chemical polish which does not introduce any defects into the substrate during the process. The method can be readily adopted in all cases where chemical polishing is practical for substrate preparation. Results similar to those obtained by the more sophisticated hydroplaning method can be achieved.

  6. Preparation of Spirocyclic β-Proline Esters

    DEFF Research Database (Denmark)

    Fjelbye, Kasper; Marigo, Mauro; Clausen, Rasmus Prætorius

    2017-01-01

    A series of novel N-Bn-protected spirocyclic β-proline esters were prepared using [3+2] cycloaddition and subsequently converted into their corresponding aldehydes. In addition, two novel N-Cbz-protected spirocyclic β-proline esters were prepared using intramolecular cyclization starting from...

  7. Leading Leadership Preparation: 21st Century Designs

    Science.gov (United States)

    Farmer, Tod Allen

    2010-01-01

    As political accountability and economic reality increasingly influence higher education, many leadership preparation programs are seeking cost effective instructional delivery systems that yield highly effective results. Simultaneously, large numbers of graduate students are seeking quality leadership preparation programs that provide both…

  8. Praxis and Poiesis in Piano Repertoire Preparation

    Science.gov (United States)

    Dos Santos, Regina Antunes Teixeira; Hentschke, Liane

    2011-01-01

    The piano repertoire preparation of three undergraduate students at three different academic levels--the first, fifth and eighth semesters--was followed during an academic semester. A phenomenological approach was used to collect data in three stages: an introductory interview, observations of the repertoire under preparation and a final…

  9. Perfect Solutions for Wearing Preparation in India

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    @@ Presentation of KARL MAYER's reorganised warp preparation business unit during a series of symposia held in India on the 19, 21 and 23 January. KARL MAYER's Warp Preparation Section continues to focus on providing an excellent customer service, and has recently been reorganised to make it even more efficient.

  10. Perfect Solutions for Weaving Preparation in india

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Presentation of KARL MAYER’s reorganised warp preparation business unit during a series of symposia held in India on the 19,21 and 23 January. KARL MAYER’s Warp Preparation Section continues to focus on providing an excellent customer service,and has recently been reorganised to make it even more efficient.Its operations were presented during the

  11. Preparing Instructional Objectives: Agony or Ecstasy?

    Science.gov (United States)

    Roberts, Wesley K.

    This paper 1) discusses the problems encountered in preparing objectives for instructional programs; 2) describes an informal research project in which seven instructional designers working on the same project attempted to determine agreement on an objective; and 3) suggests how to prepare objectives so that difficulties can be minimized. One…

  12. Final Report BW Sample Collection& Preparation Device

    Energy Technology Data Exchange (ETDEWEB)

    Koopman, R P; Belgrader, P; Meyer, G; Benett, W J; Richards, J B; Hadley, D R; Stratton, P L; Milanovich, F P

    2002-01-31

    The objective of this project was to develop the technique needed to prepare a field collected sample for laboratory analysis and build a portable integrated biological detection instrument with new miniaturized and automated sample purification capabilities. The device will prepare bacterial spores, bacterial vegetative cells, and viral particles for PCR amplification.

  13. Modular microfluidic system for biological sample preparation

    Energy Technology Data Exchange (ETDEWEB)

    Rose, Klint A.; Mariella, Jr., Raymond P.; Bailey, Christopher G.; Ness, Kevin Dean

    2015-09-29

    A reconfigurable modular microfluidic system for preparation of a biological sample including a series of reconfigurable modules for automated sample preparation adapted to selectively include a) a microfluidic acoustic focusing filter module, b) a dielectrophoresis bacteria filter module, c) a dielectrophoresis virus filter module, d) an isotachophoresis nucleic acid filter module, e) a lyses module, and f) an isotachophoresis-based nucleic acid filter.

  14. 30 CFR 57.6303 - Initiation preparation.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Initiation preparation. 57.6303 Section 57.6303 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Transportation-Surface and Underground § 57.6303 Initiation preparation. (a) Primers shall be made up only at the...

  15. 30 CFR 56.6303 - Initiation preparation.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Initiation preparation. 56.6303 Section 56.6303 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Initiation preparation. (a) Primers shall be made up only at the time of use and as close to the blast site...

  16. Grasping Preparation Enhances Orientation Change Detection

    NARCIS (Netherlands)

    Gutteling, T.P.; Kenemans, J.L.; Neggers, S.F.W.

    2011-01-01

    Preparing a goal directed movement often requires detailed analysis of our environment. When picking up an object, its orientation, size and relative distance are relevant parameters when preparing a successful grasp. It would therefore be beneficial if the motor system is able to influence early pe

  17. Geothermal resource area 9: Nye County. Area development plan

    Energy Technology Data Exchange (ETDEWEB)

    Pugsley, M.

    1981-01-01

    Geothermal Resource area 9 encompasses all of Nye County, Nevada. Within this area there are many different known geothermal sites ranging in temperature from 70/sup 0/ to over 265/sup 0/ F. Fifteen of the more major sites have been selected for evaluation in this Area Development Plan. Various potential uses of the energy found at each of the resource sites discussed in this Area Development Plan were determined after evaluating the area's physical characteristics, land ownership and land use patterns, existing population and projected growth rates, and transportation facilities, and comparing those with the site specific resource characteristics. The uses considered were divided into five main categories: electrical generation, space heating, recreation, industrial process heat, and agriculture. Within two of these categories certain subdivisions were considered separately. The findings about each of the 15 geothermal sites considered in this Area Development Plan are summarized.

  18. Geoportal "READY:Prepare, Prevent, Stay Informed"

    Science.gov (United States)

    Sole, Aurelia; Albano, Raffaele; Giuzio, Luciana; Manfreda, Salvatore; Maggio, Massimo; Presta, Aldo; Albano, Giovanni

    2014-05-01

    Information, communication, and training at all levels of a hydrogeological risk prevention culture is useful and necessary to develop the awareness among the people; this awareness can only lead to the correct application of the rules and correct behaviours that reduce the risk. A territorial system is more vulnerable to a calamitous event if there is little risk knowledge, in terms of knowledge of phenomenology of the event itself, of its own way to manifest and of the actions needed to mitigate their harmful effects. So, the Geoportal "READY: Prepare, Prevent, Stay Informed," developed by the School of Engineering at the University of Basilicata in collaboration with Paesit srl and Wat-TUBE, a spin-off of University of Basilicata, aims to inform people in an easy and correct way. This can improve the knowledge of the territory in order to promote the consciousness and awareness of the risks affecting the territory, in geo-localized form, even through using the memory of past disasters and precise directions on what to do for a tangible reduction of the risk. The Geoportal stores and dynamically integrates a series of layers that, individually, have a lower utility, but integrated into the web-based platform represent, for the prevention of the risks of the citizens, the anatomy for medicine. In fact, it makes the data not only available but concretely accessible. It is created on the "MapServer" platform, an open source web mapping suggested by the European Directives in the field of geographic database publication, and covers the Italian territory. It is designed to increase the knowledge of the areas at potential flood and landslide risk, delineated by the Authorities in the "P.A.I. (Piano di Assetto Idrogeologico"), and the elements which could possibly be involved in potential events with a particular attention to the critical infrastructures, such as bridges, railways and so on, and relevant structures, such as schools and hospitals. It permits the

  19. Status of large area CsI photocathode developments

    CERN Document Server

    Schyns, E M

    2002-01-01

    The development of large area reflective CsI photocathodes for RICH detectors is reviewed in the context of their production process and their performance. The quantum efficiencies of six large photocathodes recently produced by ALICE are compared with results available from the large photocathodes at HADES and STAR and with earlier R&D results obtained on small area samples. The CsI coating parameters and new developments in the domain of the production and the preparation of substrates are discussed in relation with the photocathode performance. (24 refs).

  20. 77 FR 51568 - Outer Continental Shelf, Gulf of Mexico, Oil and Gas Lease Sales, Western Planning Area Lease...

    Science.gov (United States)

    2012-08-24

    ... Bureau of Ocean Energy Management Outer Continental Shelf, Gulf of Mexico, Oil and Gas Lease Sales, Western Planning Area Lease Sale 233 and Central Planning Area Lease Sale 231 AGENCY: Bureau of Ocean... announced its intent to prepare a Supplemental EIS for proposed Western Planning Area (WPA) Lease Sale...