Preliminary investigation into aerosol mobilization resulting from fusion reactor disruptions

International Nuclear Information System (INIS)

Sharpe, J.P.; Bourham, M.A.; Gilligan, J.G.

1996-01-01

An experimental system has been developed to study disruption-induced aerosol mobilization for fusion accident analysis. The SIRENS high heat flux facility at North Carolina State University has been modified to closely simulate disruption conditions expected in tokamak reactors. A hot vapor is formed by an ablation-controlled arc and expansion cooled into a glass chamber, where particle condensation and growth occur. The particles are collected and analyzed for relevant transport properties (e.g. size distribution and shape). Particle characterization methods are discussed, and preliminary results based on simple analysis techniques are given. 2 refs., 6 figs

Electron Bernstein wave simulations and comparison to preliminary NSTX emission data

International Nuclear Information System (INIS)

Preinhaelter, Josef; Urban, Jakub; Pavlo, Pavol; Taylor, Gary; Diem, Steffi; Vahala, Linda; Vahala, George

2006-01-01

Simulations indicate that during flattop current discharges the optimal angles for the aiming of the National Spherical Torus Experiment (NSTX) antennae are quite rugged and basically independent of time. The time development of electron Bernstein wave emission (EBWE) at particular frequencies as well as the frequency spectrum of EBWE as would be seen by the recently installed NSTX antennae are computed. The simulation of EBWE at low frequencies (e.g., 16 GHz) agrees well with the recent preliminary EBWE measurements on NSTX. At high frequencies, the sensitivity of EBWE to magnetic field variations is understood by considering the Doppler broadened electron cyclotron harmonics and the cutoffs and resonances in the plasma. Significant EBWE variations are seen if the magnetic field is increased by as little as 2% at the plasma edge. The simulations for the low frequency antenna are compared to preliminary experimental data published separately by Diem et al. [Rev. Sci. Instrum.77 (2006)

Preliminary results of steel containment vessel model test

International Nuclear Information System (INIS)

Matsumoto, T.; Komine, K.; Arai, S.

1997-01-01

A high pressure test of a mixed-scaled model (1:10 in geometry and 1:4 in shell thickness) of a steel containment vessel (SCV), representing an improved boiling water reactor (BWR) Mark II containment, was conducted on December 11-12, 1996 at Sandia National Laboratories. This paper describes the preliminary results of the high pressure test. In addition, the preliminary post-test measurement data and the preliminary comparison of test data with pretest analysis predictions are also presented

Preliminary results of the alpha particle registration intercomparison ALRIT

International Nuclear Information System (INIS)

Paretzke, H.G.

1976-01-01

In view of the widespread interest in alpha particle registration with solid state nuclear track detectors, an international intercomparison of such measurements has been arranged. Sixteen sets of fourteen detectors each were sent to GSF-Neuherberg, there irradiated carefully with different alpha particle fields, and then returned for evaluation. Fourteen irradiation runs were made for each set simulating seven different irradiation situations commonly encountered in practical applications. The preliminary results of this intercomparison reported in this paper are based on the results of eight sets. They show good agreement with respect to the determination of track densities in the case of vertical incident alpha particles. Also the results obtained for determination of particle energies and angle of incidence in most cases were rather accurate. However, apparently it is still rather difficult to determine accurately and precisely the specific activity of alpha emitters on a thick filter positioned at some distance, i.e. for the case of 2π-incidence and a broad energy spectrum. (orig.) [de

Preliminary results of spatially resolved ECR ion beam profile investigations

International Nuclear Information System (INIS)

Panitzsch, L.; Stalder, M.; Wimmer-Schweingruber, R.F.

2012-01-01

The profile of an ion beam produced in an Electron Cyclotron Resonance Ion Source (ECRIS) can vary greatly depending on the source settings and the ion-optical tuning. Strongly focussed ion beams form circular structures (hollow beams) as predicted by simulations and observed in experiments. Each of the rings is predicted to be dominated by ions with same or at least similar m/q-ratios due to ion-optical effects. To check this we performed a series of preliminary investigations to test the required tuning capabilities of our ion source. This includes beam focussing (A) and beam steering (B) using a 3D-movable extraction. Having tuned the source to deliver a beam of strongly focussed ions of different ion species and having steered this beam to match the transmittance area of the sector magnet we also recorded the ion charge state distribution of the strongly focussed beam profile at different, spatially limited positions (C). The preliminary results will be introduced within this paper: it appears that our 3D-movable extraction is very efficient to steer and to focus the beam strongly. The paper is followed by the slides of the presentation. (authors)

Preliminary Analysis and Simulation Results of Microwave Transmission Through an Electron Cloud

International Nuclear Information System (INIS)

Sonnad, Kiran; Sonnad, Kiran; Furman, Miguel; Veitzer, Seth; Stoltz, Peter; Cary, John

2007-01-01

The electromagnetic particle-in-cell (PIC) code VORPAL is being used to simulate the interaction of microwave radiation through an electron cloud. The results so far show good agreement with theory for simple cases. The study has been motivated by previous experimental work on this problem at the CERN SPS [1], experiments at the PEP-II Low Energy Ring (LER) at SLAC [4], and proposed experiments at the Fermilab Main Injector (MI). With experimental observation of quantities such as amplitude, phase and spectrum of the output microwave radiation and with support from simulations for different cloud densities and applied magnetic fields, this technique can prove to be a useful probe for assessing the presence as well as the density of electron clouds

Simulation of lumbar and neck angle flexion while ingress of paratransit (angkot in Indonesia as a preliminary design study

Directory of Open Access Journals (Sweden)

Yukhi Mustaqim Kusuma Sya’bana

2017-12-01

Full Text Available This is the preliminary finding of a study to simulate lumbar and neck flexion while ingress to the paratransit. The result of simulation will determine design aspect criteria as a preliminary step before ideation and implementation design steps. Biomechanics of Bodies (BoB is software that used to represent passenger task during paratransit ingress simulation, with skeleton model that used is height 165 cm and weight 65 kg. Environment to represent this simulation is measured Suzuki Carry SS 2013 as a private car that has been modified into a public transportation in accordance with the Indonesian government road-worthy test. Due to the low height of the entrance and the high ground clearance, lumbar and neck joint angle was a focus of this ingress simulation. The peak angle at the neck joint is 40° when 2 s skeleton nod in the door limitation ingress and lumbar flexion is 70° when 5 s skeleton is walking while bend over that will increase the load on that area. Based on biomechanical simulation approach, we may suggest the dimension of public transportation design framework developments, especially paratransit.

Preliminary results from NOAMP deep drifting floats

International Nuclear Information System (INIS)

Ollitrault, M.

1989-01-01

This paper is a very brief and preliminary outline of first results obtained with deep SOFAR floats in the NOAMP area. The work is now going toward more precise statistical estimations of mean and variable currents, together with better tracking to resolve submesoscales and estimate diffusivities due to mesoscale and smaller scale motions. However the preliminary results confirm that the NOAMP region (and surroundings) has a deep mesoscale eddy field that is considerably more energetic that the mean field (r.m.s. velocities are of order 5 cm s -1 ), although both values are diminished compared to the western basin. A data report containing trajectories and statistics is scheduled to be published by IFREMER in the near future. The project main task is to especially study the dispersion of radioactive substances

Preliminary Experimental Results for Indirect Vector-Control of Induction Motor Drives with Forced Dynamics

Directory of Open Access Journals (Sweden)

Jan Vittek

2003-01-01

Full Text Available The contribution presents an extension of indirect vector control of electric drives employing induction motors to 'Forced Dynamic Control'. This method of control offers an accurate realisation of dynamic response profiles, which can be selected by the user. The developed system can be integrated into a drive with a shaft position encoder or a shaft sensoriess drive, in which only the stator currents are measured. The applied stator voltages are determined by a computed inverter switching algorithm. Simulation results and preliminary experimental results for indirect vector control of an idle running induction motor indicate good agreement with the theoretical predictions.

COSMIC EVOLUTION OF DUST IN GALAXIES: METHODS AND PRELIMINARY RESULTS

International Nuclear Information System (INIS)

Bekki, Kenji

2015-01-01

We investigate the redshift (z) evolution of dust mass and abundance, their dependences on initial conditions of galaxy formation, and physical correlations between dust, gas, and stellar contents at different z based on our original chemodynamical simulations of galaxy formation with dust growth and destruction. In this preliminary investigation, we first determine the reasonable ranges of the most important two parameters for dust evolution, i.e., the timescales of dust growth and destruction, by comparing the observed and simulated dust mass and abundances and molecular hydrogen (H 2 ) content of the Galaxy. We then investigate the z-evolution of dust-to-gas ratios (D), H 2 gas fraction (f H 2 ), and gas-phase chemical abundances (e.g., A O = 12 + log (O/H)) in the simulated disk and dwarf galaxies. The principal results are as follows. Both D and f H 2 can rapidly increase during the early dissipative formation of galactic disks (z ∼ 2-3), and the z-evolution of these depends on initial mass densities, spin parameters, and masses of galaxies. The observed A O -D relation can be qualitatively reproduced, but the simulated dispersion of D at a given A O is smaller. The simulated galaxies with larger total dust masses show larger H 2 and stellar masses and higher f H 2 . Disk galaxies show negative radial gradients of D and the gradients are steeper for more massive galaxies. The observed evolution of dust masses and dust-to-stellar-mass ratios between z = 0 and 0.4 cannot be reproduced so well by the simulated disks. Very extended dusty gaseous halos can be formed during hierarchical buildup of disk galaxies. Dust-to-metal ratios (i.e., dust-depletion levels) are different within a single galaxy and between different galaxies at different z

COSMIC EVOLUTION OF DUST IN GALAXIES: METHODS AND PRELIMINARY RESULTS

Energy Technology Data Exchange (ETDEWEB)

Bekki, Kenji [ICRAR, M468, The University of Western Australia, 35 Stirling Highway, Crawley, Western Australia 6009 (Australia)

2015-02-01

We investigate the redshift (z) evolution of dust mass and abundance, their dependences on initial conditions of galaxy formation, and physical correlations between dust, gas, and stellar contents at different z based on our original chemodynamical simulations of galaxy formation with dust growth and destruction. In this preliminary investigation, we first determine the reasonable ranges of the most important two parameters for dust evolution, i.e., the timescales of dust growth and destruction, by comparing the observed and simulated dust mass and abundances and molecular hydrogen (H{sub 2}) content of the Galaxy. We then investigate the z-evolution of dust-to-gas ratios (D), H{sub 2} gas fraction (f{sub H{sub 2}}), and gas-phase chemical abundances (e.g., A {sub O} = 12 + log (O/H)) in the simulated disk and dwarf galaxies. The principal results are as follows. Both D and f{sub H{sub 2}} can rapidly increase during the early dissipative formation of galactic disks (z ∼ 2-3), and the z-evolution of these depends on initial mass densities, spin parameters, and masses of galaxies. The observed A {sub O}-D relation can be qualitatively reproduced, but the simulated dispersion of D at a given A {sub O} is smaller. The simulated galaxies with larger total dust masses show larger H{sub 2} and stellar masses and higher f{sub H{sub 2}}. Disk galaxies show negative radial gradients of D and the gradients are steeper for more massive galaxies. The observed evolution of dust masses and dust-to-stellar-mass ratios between z = 0 and 0.4 cannot be reproduced so well by the simulated disks. Very extended dusty gaseous halos can be formed during hierarchical buildup of disk galaxies. Dust-to-metal ratios (i.e., dust-depletion levels) are different within a single galaxy and between different galaxies at different z.

Shallow-land burial of low-level radioactive wastes: preliminary simulations of long-term health risks

International Nuclear Information System (INIS)

Fields, D.E.; Little, C.A.; Emerson, C.J.; Hiromoto, G.

1982-01-01

PRESTO, a computer code developed for the Environmental Protection Agency for the evaluation of possible health effects associated with shallow-land rad-waste burial areas, has been used to perform simulations for three such sites. Preliminary results for the 1000 y period following site closure suggest that shallow burial, at properly chosen sites, is indeed an appropriate disposal practice for low-level wastes. Periods of maximum risk to subject populations are also inferred

Simulation of the preliminary General Electric SP-100 space reactor concept using the ATHENA computer code

International Nuclear Information System (INIS)

Fletcher, C.D.

1986-01-01

The capability to perform thermal-hydraulic analyses of a space reactor using the ATHENA computer code is demonstrated. The fast reactor, liquid-lithium coolant loops, and lithium-filled heat pipes of the preliminary General electric SP-100 design were modeled with ATHENA. Two demonstration transient calculations were performed simulating accident conditions. Calculated results are available for display using the Nuclear Plant Analyzer color graphics analysis tool in addition to traditional plots. ATHENA-calculated results appear reasonable, both for steady state full power conditions, and for the two transients. This analysis represents the first known transient thermal-hydraulic simulation using an integral space reactor system model incorporating heat pipes. 6 refs., 17 figs., 1 tab

Analysis of rainfall-induced shallow landslides in Jamne and Jaszcze stream valleys (Polish Carpathians – preliminary results

Directory of Open Access Journals (Sweden)

Zydroń Tymoteusz

2016-03-01

Full Text Available Analysis of rainfall-induced shallow landslides in Jamne and Jaszcze stream valleys (Polish Carpathians - preliminary results. Preliminary shallow landslide susceptibility mapping of the Jamne and Jaszcze stream valleys, located in the Polish Flysch Carpathians, is presented in the paper. For the purpose of mapping, there were used SINMAP and Iverson’s models integrating infiltration and slope stability calculations. The calibration of the used models parameters, obtained from limited field and laboratory tests, was performed using data from 8-9 July 1997, when as a consequence of a very intense rainfall, 94 shallow landslides were observed on meadows and arable lands. A comparison of the slope stability calculation results and the localisation of the noticed shallow landslides showed satisfactory agreement between localisation of the observed and computed unstable areas. However, it was concluded that better simulation results were obtained using Iverson’s model.

French 900 MWe PWR PSA preliminary results

International Nuclear Information System (INIS)

Lanore, J.M.; Brisbois, J.

1988-10-01

A PSA is performed by the Safety Assessment Department of CEA for a 900 MWe standardized plant. The paper presents the objectives, the scope of the study and the relative preliminary results. Some general insights are drawn, especially the benefit related to the implementation of emergency procedures

Danish Anaesthesia Allergy Centre - preliminary results

DEFF Research Database (Denmark)

Garvey, L H; Roed-Petersen, J; Menné, T

2001-01-01

BACKGROUND: Anaphylactoid reactions in anaesthesia are rare and should ideally be investigated in specialist centres. At Gentofte University Hospital, we established such a centre in 1998 as a joint venture between the Departments of Anaesthesiology and Dermatology. We present the methodology...... for chlorhexidine. Only one patient has tested positive to a neuromuscular blocking drug (NMBD) so far. DISCUSSION: Our preliminary results appear to differ in two ways from results usually found in this field. Firstly, only one patient has tested positive for a NMBD and secondly, we have had four patients...

Nuclear Reactor Component Code CUPID-I: Numerical Scheme and Preliminary Assessment Results

International Nuclear Information System (INIS)

Cho, Hyoung Kyu; Jeong, Jae Jun; Park, Ik Kyu; Kim, Jong Tae; Yoon, Han Young

2007-12-01

A component scale thermal hydraulic analysis code, CUPID (Component Unstructured Program for Interfacial Dynamics), is being developed for the analysis of components of a nuclear reactor, such as reactor vessel, steam generator, containment, etc. It adopted three-dimensional, transient, two phase and three-field model. In order to develop the numerical schemes for the three-field model, various numerical schemes have been examined including the SMAC, semi-implicit ICE, SIMPLE, Row Scheme and so on. Among them, the ICE scheme for the three-field model was presented in the present report. The CUPID code is utilizing unstructured mesh for the simulation of complicated geometries of the nuclear reactor components. The conventional ICE scheme that was applied to RELAP5 and COBRA-TF, therefore, were modified for the application to the unstructured mesh. Preliminary calculations for the unstructured semi-implicit ICE scheme have been conducted for a verification of the numerical method from a qualitative point of view. The preliminary calculation results showed that the present numerical scheme is robust and efficient for the prediction of phase changes and flow transitions due to a boiling and a flashing. These calculation results also showed the strong coupling between the pressure and void fraction changes. Thus, it is believed that the semi-implicit ICE scheme can be utilized for transient two-phase flows in a component of a nuclear reactor

Nuclear Reactor Component Code CUPID-I: Numerical Scheme and Preliminary Assessment Results

Energy Technology Data Exchange (ETDEWEB)

Cho, Hyoung Kyu; Jeong, Jae Jun; Park, Ik Kyu; Kim, Jong Tae; Yoon, Han Young

2007-12-15

A component scale thermal hydraulic analysis code, CUPID (Component Unstructured Program for Interfacial Dynamics), is being developed for the analysis of components of a nuclear reactor, such as reactor vessel, steam generator, containment, etc. It adopted three-dimensional, transient, two phase and three-field model. In order to develop the numerical schemes for the three-field model, various numerical schemes have been examined including the SMAC, semi-implicit ICE, SIMPLE, Row Scheme and so on. Among them, the ICE scheme for the three-field model was presented in the present report. The CUPID code is utilizing unstructured mesh for the simulation of complicated geometries of the nuclear reactor components. The conventional ICE scheme that was applied to RELAP5 and COBRA-TF, therefore, were modified for the application to the unstructured mesh. Preliminary calculations for the unstructured semi-implicit ICE scheme have been conducted for a verification of the numerical method from a qualitative point of view. The preliminary calculation results showed that the present numerical scheme is robust and efficient for the prediction of phase changes and flow transitions due to a boiling and a flashing. These calculation results also showed the strong coupling between the pressure and void fraction changes. Thus, it is believed that the semi-implicit ICE scheme can be utilized for transient two-phase flows in a component of a nuclear reactor.

Tissue characterization using magnetic resonance elastography: preliminary results

International Nuclear Information System (INIS)

Kruse, S.A.; Smith, J.A.; Lawrence, A.J.; Dresner, M.A.; Manduca, A.; Greenleaf, J.F.; Ehman, R.L.

2000-01-01

The well-documented effectiveness of palpation as a diagnostic technique for detecting cancer and other diseases has provided motivation for developing imaging techniques for non-invasively evaluating the mechanical properties of tissue. A recently described approach for elasticity imaging, using propagating acoustic shear waves and phase-contrast MRI, has been called magnetic resonance elastography (MRE). The purpose of this work was to conduct preliminary studies to define methods for using MRE as a tool for addressing the paucity of quantitative tissue mechanical property data in the literature. Fresh animal liver and kidney tissue specimens were evaluated with MRE at multiple shear wave frequencies. The influence of specimen temperature and orientation on measurements of stiffness was studied in skeletal muscle. The results demonstrated that all of the materials tested (liver, kidney, muscle and tissue-simulating gel) exhibit systematic dependence of shear stiffness on shear rate. These data are consistent with a viscoelastic model of tissue mechanical properties, allowing calculation of two independent tissue properties from multiple-frequency MRE data: shear modulus and shear viscosity. The shear stiffness of tissue can be substantially affected by specimen temperature. The results also demonstrated evidence of shear anisotropy in skeletal muscle but not liver tissue. The measured shear stiffness in skeletal muscle was found to depend on both the direction of propagation and polarization of the shear waves. (author)

Preliminary results from the hierarchical glitch pipeline

International Nuclear Information System (INIS)

Mukherjee, Soma

2007-01-01

This paper reports on the preliminary results obtained from the hierarchical glitch classification pipeline on LIGO data. The pipeline that has been under construction for the past year is now complete and end-to-end tested. It is ready to generate analysis results on a daily basis. The details of the pipeline, the classification algorithms employed and the results obtained with one days analysis on the gravitational wave and several auxiliary and environmental channels from all three LIGO detectors are discussed

SmallWorld Behavior of the Worldwide Active Volcanoes Network: Preliminary Results

Science.gov (United States)

Spata, A.; Bonforte, A.; Nunnari, G.; Puglisi, G.

2009-12-01

We propose a preliminary complex networks based approach in order to model and characterize volcanoes activity correlation observed on a planetary scale over the last two thousand years. Worldwide volcanic activity is in fact related to the general plate tectonics that locally drives the faults activity, that in turn controls the magma upraise beneath the volcanoes. To find correlations among different volcanoes could indicate a common underlying mechanism driving their activity and could help us interpreting the deeper common dynamics controlling their unrest. All the first evidences found testing the procedure, suggest the suitability of this analysis to investigate global volcanism related to plate tectonics. The first correlations found, in fact, indicate that an underlying common large-scale dynamics seems to drive volcanic activity at least around the Pacific plate, where it collides and subduces beneath American, Eurasian and Australian plates. From this still preliminary analysis, also more complex relationships among volcanoes lying on different tectonic margins have been found, suggesting some more complex interrelationships between different plates. The understanding of eventually detected correlations could be also used to further implement warning systems, relating the unrest probabilities of a specific volcano also to the ongoing activity to the correlated ones. Our preliminary results suggest that, as for other many physical and biological systems, an underlying organizing principle of planetary volcanoes activity might exist and it could be a small-world principle. In fact we found that, from a topological perspective, volcanoes correlations are characterized by the typical features of small-world network: a high clustering coefficient and a low characteristic path length. These features confirm that global volcanoes activity is characterized by both short and long-range correlations. We stress here the fact that numerical simulation carried out in

Reconstructing Holocene climate using a climate model: Model strategy and preliminary results

Science.gov (United States)

Haberkorn, K.; Blender, R.; Lunkeit, F.; Fraedrich, K.

2009-04-01

An Earth system model of intermediate complexity (Planet Simulator; PlaSim) is used to reconstruct Holocene climate based on proxy data. The Planet Simulator is a user friendly general circulation model (GCM) suitable for palaeoclimate research. Its easy handling and the modular structure allow for fast and problem dependent simulations. The spectral model is based on the moist primitive equations conserving momentum, mass, energy and moisture. Besides the atmospheric part, a mixed layer-ocean with sea ice and a land surface with biosphere are included. The present-day climate of PlaSim, based on an AMIP II control-run (T21/10L resolution), shows reasonable agreement with ERA-40 reanalysis data. Combining PlaSim with a socio-technological model (GLUES; DFG priority project INTERDYNAMIK) provides improved knowledge on the shift from hunting-gathering to agropastoral subsistence societies. This is achieved by a data assimilation approach, incorporating proxy time series into PlaSim to initialize palaeoclimate simulations during the Holocene. For this, the following strategy is applied: The sensitivities of the terrestrial PlaSim climate are determined with respect to sea surface temperature (SST) anomalies. Here, the focus is the impact of regionally varying SST both in the tropics and the Northern Hemisphere mid-latitudes. The inverse of these sensitivities is used to determine the SST conditions necessary for the nudging of land and coastal proxy climates. Preliminary results indicate the potential, the uncertainty and the limitations of the method.

Plans and Preliminary Results of Fundamental Studies of Ice Crystal Icing Physics in the NASA Propulsion Systems Laboratory

Science.gov (United States)

Struk, Peter; Tsao, Jen-Ching; Bartkus, Tadas

2017-01-01

This paper describes plans and preliminary results for using the NASA Propulsion Systems Lab (PSL) to experimentally study the fundamental physics of ice-crystal ice accretion. NASA is evaluating whether this facility, in addition to full-engine and motor-driven-rig tests, can be used for more fundamental ice-accretion studies that simulate the different mixed-phase icing conditions along the core flow passage of a turbo-fan engine compressor. The data from such fundamental accretion tests will be used to help develop and validate models of the accretion process. This paper presents data from some preliminary testing performed in May 2015 which examined how a mixed-phase cloud could be generated at PSL using evaporative cooling in a warmer-than-freezing environment.

Preliminary Cluster Size and Efficiencies results of CMS RPC at GIF++

CERN Document Server

Gonzalez Blanco Gonzalez, Genoveva

2016-01-01

A brief description and first preliminary results of the Efficiencies and Cluster Size measurements of the CMS Resistive Plate Chambers, will be presented inside the Gamma Irradiation Facility GIF++ at CERN. Preliminary studies that sets the base performance measurements of CMS RPC for starting aging studies.

Marvel-ous Dwarfs: Results from Four Heroically Large Simulated Volumes of Dwarf Galaxies

Science.gov (United States)

Munshi, Ferah; Brooks, Alyson; Weisz, Daniel; Bellovary, Jillian; Christensen, Charlotte

2018-01-01

We present results from high resolution, fully cosmological simulations of cosmic sheets that contain many dwarf galaxies. Together, they create the largest collection of simulated dwarf galaxies to date, with z=0 stellar masses comparable to the LMC or smaller. In total, we have simulated almost 100 luminous dwarf galaxies, forming a sample of simulated dwarfs which span a wide range of physical (stellar and halo mass) and evolutionary properties (merger history). We show how they can be calibrated against a wealth of observations of nearby galaxies including star formation histories, HI masses and kinematics, as well as stellar metallicities. We present preliminary results answering the following key questions: What is the slope of the stellar mass function at extremely low masses? Do halos with HI and no stars exist? What is the scatter in the stellar to halo mass relationship as a function of dwarf mass? What drives the scatter? With this large suite, we are beginning to statistically characterize dwarf galaxies and identify the types and numbers of outliers to expect.

Comparing the results of lattice and off-lattice simulations for the melt of nonconcatenated rings

International Nuclear Information System (INIS)

Halverson, Jonathan D; Kremer, Kurt; Grosberg, Alexander Y

2013-01-01

To study the conformational properties of unknotted and nonconcatenated ring polymers in the melt, we present a detailed qualitative and quantitative comparison of simulation data obtained by molecular dynamics simulation using an off-lattice bead-spring model and by Monte Carlo simulation using a lattice model. We observe excellent, and sometimes even unexpectedly good, agreement between the off-lattice and lattice results for many quantities measured including the gyration radii of the ring polymers, gyration radii of their subchains, contact probabilities, surface characteristics, number of contacts between subchains, and the static structure factors of the rings and their subchains. These results are, in part, put in contrast to Moore curves, and the open, linear polymer counterparts. While our analysis is extensive, our understanding of the ring melt conformations is still rather preliminary. (paper)

Preliminary results on heavy flavor physics at SLD

Energy Technology Data Exchange (ETDEWEB)

Usher, T. [Stanford Univ., CA (United States)

1994-12-01

The author reports on preliminary heavy flavor physics results from the SLD detector at the SLAC Linear Collider. Efficient tagging of b{bar b} events is achieved with an impact parameter technique that takes advantage of the small and stable interaction point of the SLC and all charged tracks in Z{sup 0} decays. This technique is applied to samples of Z{sup 0} events collected during the 1992 and 1993 physics runs. Preliminary measurements of the ratio R{sub b} = {Gamma}(Z{sup 0} {yields} b{bar b})/{Gamma}(Z{sup 0} {yields} hadrons) and the average B hadron lifetime <{tau}{sub B}> are reported. In a sample of 27K Z{sup 0} events, values of R{sub b} = 0.235 {+-} 0.006(stat.) {+-} 0.018(syst.) and <{tau}{sub B}> = 1.53 {+-} 0.006(stat.) {+-} 0.018(syst.) are obtained. In addition, the first measurement of the left-right asymmetry A{sub b} is reported. Using a sample of 38K Z{sup 0} events with a luminosity weighted electron polarization of 62%, the author obtains a preliminary value of A{sub b} = 0.94 {+-} 0.006(stat.) {+-} 0.018(syst.).

The X-Ray Pebble Recirculation Experiment (X-PREX): Facility Description, Preliminary Discrete Element Method Simulation Validation Studies, and Future Test Program

International Nuclear Information System (INIS)

Laufer, Michael R.; Bickel, Jeffrey E.; Buster, Grant C.; Krumwiede, David L.; Peterson, Per F.

2014-01-01

This paper presents a facility description, preliminary results, and future test program of the new X-Ray Pebble Recirculation Experiment (X-PREX), which is now operational and being used to collect data on the behavior of slow dense granular flows relevant to pebble bed reactor core designs. The X-PREX facility uses digital x-ray tomography methods to track both the translational and rotational motion of spherical pebbles, which provides unique experimental results that can be used to validate discrete element method (DEM) simulations of pebble motion. The validation effort supported by the X-PREX facility provides a means to build confidence in analysis of pebble bed configuration and residence time distributions that impact the neutronics, thermal hydraulics, and safety analysis of pebble bed reactor cores. Preliminary experimental and DEM simulation results are reported for silo drainage, a classical problem in the granular flow literature, at several hopper angles. These studies include conventional converging and novel diverging geometries that provide additional flexibility in the design of pebble bed reactor cores. Excellent agreement is found between the X-PREX experimental and DEM simulation results. Finally, this paper discusses additional studies in progress relevant to the design and analysis of pebble bed reactor cores including pebble recirculation in cylindrical core geometries and evaluation of forces on shut down blades inserted directly into a packed pebble bed. (author)

Economic evaluation of short-term wind power forecast in ERCOT. Preliminary results

Energy Technology Data Exchange (ETDEWEB)

Orwig, Kirsten D.; Hodge, Bri-Mathias; Brinkman, Greg; Ela, Erik; Milligan, Michael [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Banunarayanan, Venkat; Nasir, Saleh [ICF International, Fairfax, VA (United States); Freedman, Jeff [AWS Truepower, Albany, NY (United States)

2012-07-01

A number of wind energy integration studies have investigated the monetary value of using day-ahead wind power forecasts for grid operation decisions. Historically, these studies have shown that large cost savings could be gained by grid operators implementing the forecasts in their system operations. To date, none of these studies have investigated the value of shorter term (0- to 6-h ahead) wind power forecasts. In 2010, the Department of Energy and the National Oceanic and Atmospheric Administration partnered to form the Wind Forecasting Improvement Project (WFIP) to fund improvements in short-term wind forecasts and determine the economic value of these improvements to grid operators. In this work, we discuss the preliminary results of the economic benefit analysis portion of the WFIP for the Electric Reliability Council of Texas. The improvements seen in the wind forecasts are examined and the economic results of a production cost model simulation are analyzed. (orig.)

Preliminary investigations of Monte Carlo Simulations of neutron energy and LET spectra for fast neutron therapy facilities

International Nuclear Information System (INIS)

Kroc, T.K.

2009-01-01

No fast neutron therapy facility has been built with optimized beam quality based on a thorough understanding of the neutron spectrum and its resulting biological effectiveness. A study has been initiated to provide the information necessary for such an optimization. Monte Carlo studies will be used to simulate neutron energy spectra and LET spectra. These studies will be bench-marked with data taken at existing fast neutron therapy facilities. Results will also be compared with radiobiological studies to further support beam quality ptimization. These simulations, anchored by this data, will then be used to determine what parameters might be optimized to take full advantage of the unique LET properties of fast neutron beams. This paper will present preliminary work in generating energy and LET spectra for the Fermilab fast neutron therapy facility.

Preliminary results from film boiling destabilisation experiments

International Nuclear Information System (INIS)

Naylor, P.

1984-05-01

A series of experiments to investigate the triggered destabilisation of film boiling has been undertaken. Film boiling was established on a polished brass rod immersed in water and the effects of various triggers were investigated. Preliminary results are presented and two thresholds have been observed: an impulse threshold below which triggered destabilisation will not occur and a thermal threshold above which film boiling will re-establish following triggered destabilisation. (author)

Recent electron-cloud simulation results for the main damping rings of the NLC and TESLA linear colliders

International Nuclear Information System (INIS)

Pivi, M.; Raubenheimer, T.O.; Furman, M.A.

2003-01-01

In the beam pipe of the Main Damping Ring (MDR) of the Next Linear Collider (NLC), ionization of residual gases and secondary emission give rise to an electron-cloud which stabilizes to equilibrium after few bunch trains. In this paper, we present recent computer simulation results for the main features of the electron cloud at the NLC and preliminary simulation results for the TESLA main damping rings, obtained with the code POSINST that has been developed at LBNL, and lately in collaboration with SLAC, over the past 7 years. Possible remedies to mitigate the effect are also discussed. We have recently included the possibility to simulate different magnetic field configurations in our code including solenoid, quadrupole, sextupole and wiggler

Iron in hereditary retinal degeneration: PIXE microanalysis Preliminary results

International Nuclear Information System (INIS)

Sergeant, C.; Gouget, B.; Llabador, Y.; Simonoff, M.; Yefimova, M.; Courtois, Y.; Jeanny, J.C.

1999-01-01

Several types of hereditary retinal degeneration with progressive alteration of photoreceptors exist in men and animals. Recent immunohistochemical results have shown strong degradation of transferrin, the protein responsible for iron transport, in retinas of rats with hereditary retinal degeneration. Freeze-dried thin sections of rat retinas from different stages of the disease, and respective coeval control sections, have been analyzed using nuclear microprobe. In this first part of the study, the rat retinas at post-natal stages of 35 and 45 days have been analyzed. The sample preparation and the post-irradiation staining to determine precisely the retinal layers involved are described. Preliminary results of element distributions (K, Ca, Fe) in the rat retina layers are discussed. A very high content of calcium in the choriocapillaris of dystrophic rat retinas was observed. Preliminary results on iron distribution in the rat retina layers are presented

Preliminary report of the Hepatic Encephalopathy Assessment Driving Simulator (HEADS) score.

Science.gov (United States)

Baskin-Bey, Edwina S; Stewart, Charmaine A; Mitchell, Mary M; Bida, John P; Rosenthal, Theodore J; Nyberg, Scott L

2008-01-01

Audiovisual simulations of real-life driving (ie, driving simulators) have been used to assess neurologic dysfunction in a variety of medical applications. However, the use of simulated driving to assess neurologic impairment in the setting of liver disease (ie, hepatic encephalopathy) is limited. The aim of this analysis was to develop a scoring system based on simulated driving performance to assess mild cognitive impairment in cirrhotic patients with hepatic encephalopathy. This preliminary analysis was conducted as part of the Hepatic Encephalopathy Assessment Driving Simulator (HEADS) pilot study. Cirrhotic volunteers initially underwent a battery of neuropsychological tests to identify those cirrhotic patients with mild cognitive impairment. Performance during an audiovisually simulated course of on-road driving was then compared between mildly impaired cirrhotic patients and healthy volunteers. A scoring system was developed to quantify the likelihood of cognitive impairment on the basis of data from the simulated on-road driving. Mildly impaired cirrhotic patients performed below the level of healthy volunteers on the driving simulator. Univariate logistic regression and correlation models indicated that several driving simulator variables were significant predictors of cognitive impairment. Five variables (run time, total map performance, number of collisions, visual divided attention response, and average lane position) were incorporated into a quantitative model, the HEADS scoring system. The HEADS score (0-9 points) showed a strong correlation with cognitive impairment as measured by area under the receiver-operator curve (.89). The HEADS system appears to be a promising new tool for the assessment of mild hepatic encephalopathy.

Preliminary results of the Adone storage ring FEL experiment, LELA

International Nuclear Information System (INIS)

Barbini, R.; Vignola, G.; Trillo, S.

1983-01-01

A short description of the LELA (Free Electron Laser on Adone) experiment is given. Results on the spontaneous radiation angle and energy spectra and preliminary results on optical gain measurements are also discussed

The Geographic Climate Information System Project (GEOCLIMA): Overview and preliminary results

Science.gov (United States)

Feidas, H.; Zanis, P.; Melas, D.; Vaitis, M.; Anadranistakis, E.; Symeonidis, P.; Pantelopoulos, S.

2012-04-01

The project GEOCLIMA aims at developing an integrated Geographic Information System (GIS) allowing the user to manage, analyze and visualize the information which is directly or indirectly related to climate and its future projections in Greece. The main components of the project are: a) collection and homogenization of climate and environmental related information, b) estimation of future climate change based on existing regional climate model (RCM) simulations as well as a supplementary high resolution (10 km x 10 km) simulation over the period 1961-2100 using RegCM3, c) compilation of an integrated uniform geographic database, and d) mapping of climate data, creation of digital thematic maps, and development of the integrated web GIS application. This paper provides an overview of the ongoing research efforts and preliminary results of the project. First, the trends in the annual and seasonal time series of precipitation and air temperature observations for all available stations in Greece are assessed. Then the set-up of the high resolution RCM simulation (10 km x 10 km) is discussed with respect to the selected convective scheme. Finally, the relationship of climatic variables with geophysical features over Greece such as altitude, location, distance from the sea, slope, aspect, distance from climatic barriers, land cover etc) is investigated, to support climate mapping. The research has been co-financed by the European Union (European Regional Development Fund) and Greek national funds through the Operational Program "Competitiveness and Entrepreneurship" of the National Strategic Reference Framework (NSRF) - Research Funding Program COOPERATION 2009.

Preliminary results of testing bioassay analytical performance standards

International Nuclear Information System (INIS)

Fisher, D.R.; Robinson, A.V.; Hadley, R.T.

1983-08-01

The analytical performance of both in vivo and in vitro bioassay laboratories is being studied to determine the capability of these laboratories to meet the minimum criteria for accuracy and precision specified in the draft ANSI Standard N13.30, Performance Criteria for Radiobioassay. This paper presents preliminary results of the first round of testing

Preliminary numerical simulations of the 27 February 2010 Chile tsunami: first results and hints in a tsunami early warning perspective

Science.gov (United States)

Tinti, S.; Tonini, R.; Armigliato, A.; Zaniboni, F.; Pagnoni, G.; Gallazzi, Sara; Bressan, Lidia

2010-05-01

The tsunamigenic earthquake (M 8.8) that occurred offshore central Chile on 27 February 2010 can be classified as a typical subduction-zone earthquake. The effects of the ensuing tsunami have been devastating along the Chile coasts, and especially between the cities of Valparaiso and Talcahuano, and in the Juan Fernandez islands. The tsunami propagated across the entire Pacific Ocean, hitting with variable intensity almost all the coasts facing the basin. While the far-field propagation was quite well tracked almost in real-time by the warning centres and reasonably well reproduced by the forecast models, the toll of lives and the severity of the damage caused by the tsunami in the near-field occurred with no local alert nor warning and sadly confirms that the protection of the communities placed close to the tsunami sources is still an unresolved problem in the tsunami early warning field. The purpose of this study is two-fold. On one side we perform numerical simulations of the tsunami starting from different earthquake models which we built on the basis of the preliminary seismic parameters (location, magnitude and focal mechanism) made available by the seismological agencies immediately after the event, or retrieved from more detailed and refined studies published online in the following days and weeks. The comparison with the available records of both offshore DART buoys and coastal tide-gauges is used to put some preliminary constraints on the best-fitting fault model. The numerical simulations are performed by means of the finite-difference code UBO-TSUFD, developed and maintained by the Tsunami Research Team of the University of Bologna, Italy, which can solve both the linear and non-linear versions of the shallow-water equations on nested grids. The second purpose of this study is to use the conclusions drawn in the previous part in a tsunami early warning perspective. In the framework of the EU-funded project DEWS (Distant Early Warning System), we will

Preliminary Three-Dimensional Simulation of Sediment and Cesium Transport in the Ogi Dam Reservoir using FLESCOT – Task 6, Subtask 2

Energy Technology Data Exchange (ETDEWEB)

Onishi, Yasuo; Kurikami, Hiroshi; Yokuda, Satoru T.

2014-03-28

After the accident at the Fukushima Daiichi Nuclear Power Plant in March 2011, the Japan Atomic Energy Agency and the Pacific Northwest National Laboratory initiated a collaborative project on environmental restoration. In October 2013, the collaborative team started a task of three-dimensional modeling of sediment and cesium transport in the Fukushima environment using the FLESCOT (Flow, Energy, Salinity, Sediment Contaminant Transport) code. As the first trial, we applied it to the Ogi Dam Reservoir that is one of the reservoirs in the Japan Atomic Energy Agency’s (JAEA’s) investigation project. Three simulation cases under the following different temperature conditions were studied: • incoming rivers and the Ogi Dam Reservoir have the same water temperature • incoming rivers have lower water temperature than that of the reservoir • incoming rivers have higher water temperature than that of the reservoir. The preliminary simulations suggest that seasonal temperature changes influence the sediment and cesium transport. The preliminary results showed the following: • Suspended sand, and cesium adsorbed by sand, coming into the reservoirs from upstream rivers is deposited near the reservoir entrance. • Suspended silt, and cesium adsorbed by silt, is deposited farther in the reservoir. • Suspended clay, and cesium adsorbed by clay, travels the farthest into the reservoir. With sufficient time, the dissolved cesium reaches the downstream end of the reservoir. This preliminary modeling also suggests the possibility of a suitable dam operation to control the cesium migration farther downstream from the dam. JAEA has been sampling in the Ogi Dam Reservoir, but these data were not yet available for the current model calibration and validation for this reservoir. Nonetheless these preliminary FLESCOT modeling results were qualitatively valid and confirmed the applicability of the FLESCOT code to the Ogi Dam Reservoir, and in general to other reservoirs in

Preliminary results from a simulated laboratory experiment or an encounter of cluster satellite probes with a reconnection layer

Science.gov (United States)

Yamada, M.; Ren, Y.; Ji, H.; Gerhardt, S.; Darfman, S.

2006-12-01

With the recent upgrade of the MRX (Magnetic Reconnection Experiment) device[1], our experimental operation allows us to carry out a jog experiment in which a current sheet can be moved swiftly across an inserted probe assembly. A cluster of probes with variable distances can be inserted into a known desired position in the MRX device. This setup can be similar to the situation in which a cluster of satellites encounters a rapidly moving reconnection layer. If necessary, we can create a neutral sheet where the density of one side is significantly higher than the other, as is the case for the magnetopause. A variable guide field will be applied to study its effect on reconnection. We proposed[2] to document basic patterns of data during a simulated encounter of the MRX reconnection layer with the four-probe mock-up system and compare them with data acquired from past satellites. Relative position of the MMS satellites in the magnetosphere can then be determined. Optimum cluster configuration or distance between the four satellites can be determined for various diagnostics or research missions. The relationship of magnetic fluctuations[3] with the observed out-of- plane quadrupole field, a characteristic signature of the Hall MHD, can be also studied in this series of experiments. In this paper, results from a preliminary experiment will be presented. These experiments utilize effectively the unique MRX ability to accurately know the location of diagnostics with respect to the moving reconnection layer. Supported by DoE, NASA, NSF. [1] M. Yamada et al, Phys. Plasmas 13, 052119 (2006), [2] M.Yamada et al, MMS-IDS proposal (2006), [3] H. Ji et al, Phys. Rev. Letts. 92, 115001 (2004)

Preliminary test results from a telescope of Hughes pixel arrays at FNAL

International Nuclear Information System (INIS)

Jernigan, J.G.; Arens, J.; Vezie, D.; Collins, T.; Krider, J.; Skubic, P.

1992-09-01

In December of 1991 three silicon hybrid pixel detectors each having 2.56 x 2.56 pixels 30 μm square, made by the Hughes Aircraft Company, were placed in a high energy muon beam at the Fermi National Accelerator Laboratory. Straight tracks were recorded in these detectors at angles to the normal to the plane of the silicon ranging from 0 to 45 degrees. In this note, preliminary results are presented on the straight through tracks, i.e., those passing through the telescope at normal incidence. Pulse height data, signal-to-noise data, and preliminary straight line fits to the data resulting in residual distributions are presented. Preliminary calculations show spatial resolution of less than 5 μm in two dimensions

Simulation training for emergency obstetric and neonatal care in Senegal preliminary results.

Science.gov (United States)

Gueye, M; Moreira, P M; Faye-Dieme, M E; Ndiaye-Gueye, M D; Gassama, O; Kane-Gueye, S M; Diouf, A A; Niang, M M; Diadhiou, M; Diallo, M; Dieng, Y D; Ndiaye, O; Diouf, A; Moreau, J C

2017-06-01

To describe a new training approach for emergency obstetric and neonatal care (EmONC) introduced in Senegal to strengthen the skills of healthcare providers. The approach was based on skills training according to the so-called "humanist" method and on "lifesaving skills". Simulated practice took place in the classroom through 13 clinical stations summarizing the clinical skills needed for EmONC. Evaluation took place in all phases, and the results were recorded in a database to document the progress of each learner. This approach was used to train 432 providers in 10 months and to document the increase in each participants' technical achievements. The combination of training with the "learning by doing" model ensured that providers learned and mastered all EmONC skills and reduced the missed learning opportunities observed in former EmONC training sessions. Assessing the impact of training on EmONC indicators and introducing this learning modality in basic training are the two major challenges we currently face.

Preliminary results from initial in-pile debris bed experiments

International Nuclear Information System (INIS)

Rivard, J.B.

1977-01-01

An accident in a liquid metal fast breeder reactor (LMFBR) in which molten core material is suddenly quenched with subcooled liquid sodium could result in extensive fragmentation and dispersal of fuel as subcritical beds of frozen particulate debris within the reactor vessel. Since this debris will continue to generate power due to decay of retained fission products, containment of the debris is threatened if the generated heat is not removed. Therefore, the initial safety question is the capacity which debris beds may have for transfer of the decay heat to overlying liquid sodium by natural processes--i.e., without the aid of forced circulation of the coolant. Up to the present time, all experiments on debris bed behavior either have used substitute materials (e.g., sand and water) or have employed actual materials, but atypical heating methods. Increased confidence in the applicability of debris bed simulations is afforded if the heat is generated within the fuel component of the appropriate fast reactor materials. The initial series of in-pile tests reported on herein constitutes the first experiments in which the internal heating mode has been produced in particulate oxide fuel immersed in liquid sodium. Fission heating of the fully-enriched UO 2 in the experiment while it is contained within Sandia Laboratories Annular Core Pulse Reactor (ACPR), operating in its steady-state mode, approximates the decay heating of debris. Preliminary results are discussed

Large-scale Validation of AMIP II Land-surface Simulations: Preliminary Results for Ten Models

Energy Technology Data Exchange (ETDEWEB)

Phillips, T J; Henderson-Sellers, A; Irannejad, P; McGuffie, K; Zhang, H

2005-12-01

This report summarizes initial findings of a large-scale validation of the land-surface simulations of ten atmospheric general circulation models that are entries in phase II of the Atmospheric Model Intercomparison Project (AMIP II). This validation is conducted by AMIP Diagnostic Subproject 12 on Land-surface Processes and Parameterizations, which is focusing on putative relationships between the continental climate simulations and the associated models' land-surface schemes. The selected models typify the diversity of representations of land-surface climate that are currently implemented by the global modeling community. The current dearth of global-scale terrestrial observations makes exacting validation of AMIP II continental simulations impractical. Thus, selected land-surface processes of the models are compared with several alternative validation data sets, which include merged in-situ/satellite products, climate reanalyses, and off-line simulations of land-surface schemes that are driven by observed forcings. The aggregated spatio-temporal differences between each simulated process and a chosen reference data set then are quantified by means of root-mean-square error statistics; the differences among alternative validation data sets are similarly quantified as an estimate of the current observational uncertainty in the selected land-surface process. Examples of these metrics are displayed for land-surface air temperature, precipitation, and the latent and sensible heat fluxes. It is found that the simulations of surface air temperature, when aggregated over all land and seasons, agree most closely with the chosen reference data, while the simulations of precipitation agree least. In the latter case, there also is considerable inter-model scatter in the error statistics, with the reanalyses estimates of precipitation resembling the AMIP II simulations more than to the chosen reference data. In aggregate, the simulations of land-surface latent and

Connecticut Transit (CTTRANSIT) Fuel Cell Transit Bus: Preliminary Evaluation Results

Energy Technology Data Exchange (ETDEWEB)

Chandler, K.; Eudy, L.

2008-10-01

This report provides preliminary results from a National Renewable Energy Laboratory evaluation of a protoptye fuel cell transit bus operating at Connecticut Transit in Hartford. Included are descriptions of the planned fuel cell bus demonstration and equipment; early results and agency experience are also provided.

Preliminary results of a PWA of the centrally produced {phi}{phi} system

Energy Technology Data Exchange (ETDEWEB)

Marco A. Reyes et al.

2001-11-02

The authors present preliminary results of a Partial Wave Analysis of the centrally produced {phi}{phi} system at 800 GeV/c in the reaction pp {yields} p{sub slow} ({phi}{phi})p{sub fast}. The preliminary results with one and two M = 0 waves, indicate that most of the cross section can be described by two waves, with J{sup PC} LS{sup {eta}} = 2{sup 2}02{sup -1}, 0{sup 2}00{sup -1}.

The Agricultural Model Intercomparison and Improvement Project (AgMIP): Progress and Preliminary Results

Science.gov (United States)

Rosenzweig, C.

2011-12-01

The Agricultural Model Intercomparison and Improvement Project (AgMIP) is a distributed climate-scenario simulation exercise for historical model intercomparison and future climate change conditions with participation of multiple crop and agricultural trade modeling groups around the world. The goals of AgMIP are to improve substantially the characterization of risk of hunger and world food security due to climate change and to enhance adaptation capacity in both developing and developed countries. Recent progress and the current status of AgMIP will be presented, highlighting three areas of activity: preliminary results from crop pilot studies, outcomes from regional workshops, and emerging scientific challenges. AgMIP crop modeling efforts are being led by pilot studies, which have been established for wheat, maize, rice, and sugarcane. These crop-specific initiatives have proven instrumental in testing and contributing to AgMIP protocols, as well as creating preliminary results for aggregation and input to agricultural trade models. Regional workshops are being held to encourage collaborations and set research activities in motion for key agricultural areas. The first of these workshops was hosted by Embrapa and UNICAMP and held in Campinas, Brazil. Outcomes from this meeting have informed crop modeling research activities within South America, AgMIP protocols, and future regional workshops. Several scientific challenges have emerged and are currently being addressed by AgMIP researchers. Areas of particular interest include geospatial weather generation, ensemble methods for climate scenarios and crop models, spatial aggregation of field-scale yields to regional and global production, and characterization of future changes in climate variability.

Danish Anaesthesia Allergy Centre - preliminary results

DEFF Research Database (Denmark)

Garvey, L H; Roed-Petersen, J; Menné, T

2001-01-01

BACKGROUND: Anaphylactoid reactions in anaesthesia are rare and should ideally be investigated in specialist centres. At Gentofte University Hospital, we established such a centre in 1998 as a joint venture between the Departments of Anaesthesiology and Dermatology. We present the methodology...... of in vitro testing and skin testing. Blood samples for tryptase analysis are taken at the time of reaction and a control sample is taken together with samples for specific IgE analysis 2-4 weeks after the reaction. Subsequent skin testing comprises both prick tests and intradermal tests in most cases...... for chlorhexidine. Only one patient has tested positive to a neuromuscular blocking drug (NMBD) so far. DISCUSSION: Our preliminary results appear to differ in two ways from results usually found in this field. Firstly, only one patient has tested positive for a NMBD and secondly, we have had four patients...

King County Metro Battery Electric Bus Demonstration: Preliminary Project Results

Energy Technology Data Exchange (ETDEWEB)

2017-05-22

The U.S. Federal Transit Administration (FTA) funds a variety of research projects that support the commercialization of zero-emission bus technology. To evaluate projects funded through these programs, FTA has enlisted the help of the National Renewable Energy Laboratory (NREL) to conduct third-party evaluations of the technologies deployed under the FTA programs. NREL works with the selected agencies to evaluate the performance of the zero-emission buses compared to baseline conventional buses in similar service. The evaluation effort will advance the knowledge base of zero-emission technologies in transit bus applications and provide 'lessons learned' to aid other fleets in incrementally introducing next generation zero-emission buses into their operations. This report provides preliminary performance evaluation results from a demonstration of three zero-emission battery electric buses at King County Metro in King County, Washington. NREL developed this preliminary results report to quickly disseminate evaluation results to stakeholders. Detailed evaluation results will be published in future reports.

Sub-millimeter planar imaging with positron emitters: EGS4 code simulation and experimental results

International Nuclear Information System (INIS)

Bollini, D.; Del Guerra, A.; Di Domenico, G.

1996-01-01

Experimental data for Planar Imaging with positron emitters (pulse height, efficiency and spatial resolution) obtained with two matrices of 25 crystals (2 x 2 x 30 mm 3 each) of YAP:Ce coupled with a Position Sensitive PhotoMultiplier (Hamamatsu R2486-06) have been reproduced with high accuracy using the EGS4 code. Extensive simulation provides a detailed description of the performance of this type of detector as a function of the matrix granularity, the geometry of the detector and detection threshold. We present the Monte Carlo simulation and the preliminary experimental results of a prototype planar imaging system made of two matrices, each one consisting of 400 (2 x 2 x 30 mm 3 ) crystals of YAP-Ce

A Preliminary Study on Time Projection Chamber Simulation for Fission Cross Section Measurements with Geant4

International Nuclear Information System (INIS)

Kim, Jong Woon; Lee, Youngouk; Kim, Jae Cheon

2014-01-01

We present the details of the TPC simulation with Geant4 and show the results. TPC can provide more information than a fission chamber in that it is possible to distinguish different particle types. Simulations are conducted for uranium and plutonium targets with 20MeV neutrons. The simulation results are compared with the reference and show reasonable results. This is the first phase of study for realizing a TPC in the NFS at RAON, and we have more work to do, such as applying an electric field, signal processing in the simulation, and manufacturing of a TPC. The standard in fission cross section measurement is a fission chamber. It is basically just two parallel plates separated by a few centimeters of gas. A power supply connected to the plates sets up a moderate electric field. The target is deposited onto one of the plates. When fission occurs, the fragments ionize the gas, and the electric field causes the produced electrons to drift to the opposite plate, which records the total energy deposited in the chamber. A Time Projection Chamber (TPC) is a gas ionization detector similar to a fission chamber. However, it can measure the charged particle trajectories in the active volume in three dimensions by adding several readouts on the pad plane (fission chamber has only one readout one a pad plane). The specific ionization for each particle track enables the TPC to distinguish different particle types. A TPC will be used for fission cross section measurements in the Neutron Science Facility (NSF) at RAON. As a preliminary study, we present details of TPC simulation with Geant4 and discuss the results

Structural investigations of biogenic iron oxide samples. Preliminary results

International Nuclear Information System (INIS)

Balasoiu, M.; Kuklin, A.I.; Orelovich, O.L.; Kovalev, Yu.S.; Arzumanyan, G.M.; Kurkin, T.S.; Stolyar, S.V.; Iskhakov, R.S.; Rajkher, Yu.L.

2008-01-01

Some preliminary results on morphology and structure of iron oxide particles formed inside Klebsiella oxytoca bacteria are presented. In particular, by means of optical microscopy, scanning electron microscopy and small-angle X-ray scattering the effect of the bacteria age (the duration of growth) on the nanoparticles properties is studied

Spinel dissolution via addition of glass forming chemicals. Results of preliminary experiments

Energy Technology Data Exchange (ETDEWEB)

Fox, K. M. [Savannah River Site (SRS), Aiken, SC (United States); Johnson, F. C. [Savannah River Site (SRS), Aiken, SC (United States)

2015-11-01

Increased loading of high level waste in glass can lead to crystallization within the glass. Some crystalline species, such as spinel, have no practical impact on the chemical durability of the glass, and therefore may be acceptable from both a processing and a product performance standpoint. In order to operate a melter with a controlled amount of crystallization, options must be developed for remediating an unacceptable accumulation of crystals. This report describes preliminary experiments designed to evaluate the ability to dissolve spinel crystals in simulated waste glass melts via the addition of glass forming chemicals (GFCs).

A two-parameter preliminary optimization study for a fluidized-bed boiler through a comprehensive mathematical simulator

Energy Technology Data Exchange (ETDEWEB)

Rabi, Jose A.; Souza-Santos, Marcio L. de [Universidade Estadual de Campinas, SP (Brazil). Faculdade de Engenharia Mecanica. Dept. de Energia]. E-mails: jrabi@fem.unicamp.br; dss@fem.unicamp.br

2000-07-01

Modeling and simulation of fluidized-bed equipment have demonstrated their importance as a tool for design and optimization of industrial equipment. Accordingly, this work carries on an optimization study of a fluidized-bed boiler with the aid of a comprehensive mathematical simulator. The configuration data of the boiler are based on a particular Babcock and Wilcox Co. (USA) test unit. Due to their importance, the number of tubes in the bed section and the air excess are chosen as the parameters upon which the optimization study is based. On their turn, the fixed-carbon conversion factor and the boiler efficiency are chosen as two distinct optimization objectives. The results from both preliminary searches are compared. The present work is intended to be just a study on possible routes for future optimization of larger boilers. Nonetheless, the present discussion might give some insight on the equipment behavior. (author)

Remote sensing using hydroacoustics preliminary results

International Nuclear Information System (INIS)

Hunt, G.; Patrick, P.H.; Sim, B.

1989-01-01

A laboratory investigation was conducted to determine the capability and accuracy of a dual beam sonar system in classifying various targets. The ability to classify fish and/or distinguish fish from debris is essential if hydroacoustics are ever to be used truly remotely for hydroelectric power plant fish passage facilities. Preliminary results indicated that considerable filtering was occurring in the sonar sounder which limited its use in target classification. A wideband sonar detection module was developed which allowed for a more detailed reflected signal which probably will be necessary for fish identification. Another advantage that this modification appears to have over the existing system is an improved spatial resolution of targets, which can be significant if biomass estimates are based on echo counting techniques rather than echo integration ones. Based on the results, it may be possible to filter out or remove the influence of air bubbles in echo returns. As a result echo counts could more accurately be defined as fish counts. Target strengths of sturgeon were estimated using both the modified and original sounder. 12 refs., 11 figs., 2 tabs

Preliminary results of statistical dynamic experiments on a heat exchanger

International Nuclear Information System (INIS)

Corran, E.R.; Cummins, J.D.

1962-10-01

The inherent noise signals present in a heat exchanger have been recorded and analysed in order to determine some of the statistical dynamic characteristics of the heat exchanger. These preliminary results show that the primary side temperature frequency response may be determined by analysing the inherent noise. The secondary side temperature frequency response and cross coupled temperature frequency responses between primary and secondary are poorly determined because of the presence of a non-stationary noise source in the secondary circuit of this heat exchanger. This may be overcome by correlating the dependent variables with an externally applied noise signal. Some preliminary experiments with an externally applied random telegraph type of signal are reported. (author)

Preliminary result and upgrade from WISPDMX Phase II

Energy Technology Data Exchange (ETDEWEB)

Nguyen, Le Hoang; Horns, Dieter [Institut fur Experimentalphysik, Universitat Hamburg (Germany); Lobanov, Andrei [Institut fur Experimentalphysik, Universitat Hamburg (Germany); Max-Planck-Institut fur Radioastronomie, Bonn (Germany)

2016-07-01

The microwave cavity experiment WISPDMX is the first direct WISP (Weakly interactive slim particles) dark matter search experiment probing the particle masses in the 0.8-2.0 eV range. The first stage of WISPDMX measurements has been completed at nominal resonant frequencies of the cavity. The upgrading of the data acquisition and analysing has been done to increase the sensitivity of the experiment. We report preliminary result from the cavity tuning at second stage of WISPDMX.

1ST-TRIMESTER SCREENING FOR FETAL CHROMOSOMAL-ABNORMALITIES - PRELIMINARY-RESULTS

NARCIS (Netherlands)

VANLITH, JMM

We have started a multicentre trial to study the possibilities of first-trimester maternal serum screening for fetal chromosomal abnormalities. Maternal blood samples were obtained before 13 weeks of gestation. We present the preliminary results of the first 950 patients on alpha-fetoprotein (AFP).

Preliminary results of neutron production in Sahand plasma focus device

International Nuclear Information System (INIS)

Siahpoush, V.; Mohammadi, M.A.; Khorram, S.; Shabani, I.; Borhanian, J.; Ashrafi, S.; Naghshara, H.; Moslehi-Fard, M.; Sobhanian, S.

2004-01-01

We report in this paper the preliminary results of neutron generation during fusion reaction in deuterium in the Sahand Filipov type plasma focus, recently installed and put in operation at Tabriz University. The special calibration procedure for neutron detection system, using activation method is described

Preliminary Results of the Louisiana Sex Offender Treatment Program

Directory of Open Access Journals (Sweden)

Lee A. Underwood

2015-12-01

Full Text Available The purpose of this study was to offer preliminary support for the Louisiana Sex Offender Treatment Program (LSOTP in addressing the needs of juvenile sex offenders. Research objectives were (1 to offer statistical evidence for reductions in anxiety, depression, cognitive distortion and negative attitudes towards women comparing a group of 21 adolescents, 12 of whom received services as usual and nine of whom participated in the LSOTP. A controlled experimental evaluation design was utilized. The juvenile sex offenders were randomly assigned to the experimental group for 12 weeks receiving treatment services and a control group receiving care “as usual” in a residential group care program. Participants in the experimental group experienced statistically significant decreases in cognitive distortions related specifically to rape and molestation.The results of this study offer preliminary support of the LSOTP as a best practices alternative to other treatment modalities.

Visual-spatial ability is more important than motivation for novices in surgical simulator training: a preliminary study.

Science.gov (United States)

Schlickum, Marcus; Hedman, Leif; Felländer-Tsai, Li

2016-02-21

To investigate whether surgical simulation performance and previous video gaming experience would correlate with higher motivation to further train a specific simulator task and whether visual-spatial ability would rank higher in importance to surgical performance than the above. It was also examined whether or not motivation would correlate with a preference to choose a surgical specialty in the future and if simulator training would increase the interest in choosing that same work field. Motivation and general interest in surgery was measured pre- and post-training in 30 medical students at Karolinska Institutet who were tested in a laparoscopic surgical simulator in parallel with measurement of visual-spatial ability and self-estimated video gaming experience. Correlations between simulator performance metrics, visual-spatial ability and motivation were statistically analyzed using regression analysis. A good result in the first simulator trial correlated with higher self-determination index (r =-0.46, p=0.05) in male students. Visual-spatial ability was the most important underlying factor followed by intrinsic motivation score and finally video gaming experience (p=0.02, p=0.05, p=0.11) regarding simulator performance in male students. Simulator training increased interest in surgery when studying all subjects (p=0.01), male subjects (p=0.02) as well as subjects with low video gaming experience (p=0.02). This preliminary study highlights individual differences regarding the effect of simulator training on motivation that can be taken into account when designing simulator training curricula, although the sample size is quite small and findings should be interpreted carefully.

Preliminary results of the aerosol optical depth retrieval in Johor, Malaysia

International Nuclear Information System (INIS)

Lim, H Q; Lau, A M S; Kanniah, K D

2014-01-01

Monitoring of atmospheric aerosols over the urban area is important as tremendous amounts of pollutants are released by industrial activities and heavy traffic flow. Air quality monitoring by satellite observation provides better spatial coverage, however, detailed aerosol properties retrieval remains a challenge. This is due to the limitation of aerosol retrieval algorithm on high reflectance (bright surface) areas. The aim of this study is to retrieve aerosol optical depth over urban areas of Iskandar Malaysia; the main southern development zone in Johor state, using Moderate Resolution Imaging Spectroradiometer (MODIS) 500 m resolution data. One of the important steps is the aerosol optical depth retrieval is to characterise different types of aerosols in the study area. This information will be used to construct a Look Up Table containing the simulated aerosol reflectance and corresponding aerosol optical depth. Thus, in this study we have characterised different aerosol types in the study area using Aerosol Robotic Network (AERONET) data. These data were processed using cluster analysis and the preliminary results show that the area is consisting of coastal urban (65%), polluted urban (27.5%), dust particles (6%) and heavy pollution (1.5%) aerosols

Description and preliminary evaluation of a diabetes technology simulation course.

Science.gov (United States)

Wilson, Rebecca D; Bailey, Marilyn; Boyle, Mary E; Seifert, Karen M; Cortez, Karla Y; Baker, Leslie J; Hovan, Michael J; Stepanek, Jan; Cook, Curtiss B

2013-11-01

We aim to provide data on a diabetes technology simulation course (DTSC) that instructs internal medicine residents in the use of continuous subcutaneous insulin infusion (CSII) and continuous glucose monitoring system (CGMS) devices. The DTSC was implemented during calendar year 2012 and conducted in the institution's simulation center. It consisted of a set of prerequisites, a practicum, and completion of a web-based inpatient CSII-ordering simulation. DTSC participants included only those residents in the outpatient endocrinology rotation. Questionnaires were used to determine whether course objectives were met and to assess the satisfaction of residents with the course. Questionnaires were also administered before and after the endocrine rotation to gauge improvement in familiarity with CSII and CGMS technologies. During the first year, 12 of 12 residents in the outpatient endocrinology rotation completed the DTSC. Residents reported that the course objectives were fully met. The mean satisfaction score with the course ranged from 4.0 to 4.9 (maximum, 5), with most variables rated above 4.5. Self-reported familiarity with the operation of CSII and CGMS devices increased significantly in the postrotation survey compared with that on the prerotation survey (both p technologies. In light of these preliminary findings, the course will continue to be offered, with further data accrual. Future work will involve piloting the DTSC approach among other types of providers, such as residents in other specialties or inpatient nursing staff. © 2013 Diabetes Technology Society.

Trade-off results and preliminary designs of Near-Term Hybrid Vehicles

Science.gov (United States)

Sandberg, J. J.

1980-01-01

Phase I of the Near-Term Hybrid Vehicle Program involved the development of preliminary designs of electric/heat engine hybrid passenger vehicles. The preliminary designs were developed on the basis of mission analysis, performance specification, and design trade-off studies conducted independently by four contractors. THe resulting designs involve parallel hybrid (heat engine/electric) propulsion systems with significant variation in component selection, power train layout, and control strategy. Each of the four designs is projected by its developer as having the potential to substitute electrical energy for 40% to 70% of the petroleum fuel consumed annually by its conventional counterpart.

Preliminary test results for post irradiation examination on the HTTR fuel

International Nuclear Information System (INIS)

Ueta, Shohei; Umeda, Masayuki; Sawa, Kazuhiro; Sozawa, Shizuo; Shimizu, Michio; Ishigaki, Yoshinobu; Obata, Hiroyuki

2007-01-01

The future post-irradiation program for the first-loading fuel of the HTTR is scheduled using the HTTR fuel handling facilities and the Hot Laboratory in the Japan Materials Testing Reactor (JMTR) to confirm its irradiation resistance and to obtain data on its irradiation characteristics in the core. This report describes the preliminary test results and the future plan for a post-irradiation examination for the HTTR fuel. In the preliminary test, fuel compacts made with the same SiC-coated fuel particle as the first loading fuel were used. In the preliminary test, dimension, weight, fuel failure fraction, and burnup were measured, and X-ray radiograph, SEM, and EPMA observations were carried out. Finally, it was confirmed that the first-loading fuel of the HTTR showed good quality under an irradiation condition. The future plan for the post-irradiation tests was described to confirm its irradiation performance and to obtain data on its irradiation characteristics in the HTTR core. (author)

Preliminary results of an oilspill risk analysis for the Bombay High Region

Digital Repository Service at National Institute of Oceanography (India)

Mascarenhas, A.A.M.Q.; Gouveia, A.D.; Sitaraman, R.

oil were analysed, covering estimates of the time between spill occurrence and contact with resources. The combined results yielded estimates of the overall risks associated with production within the developmental area. Preliminary results...

Numerical Modelling and Simulation of Dynamic Parameters for Vibration Driven Mobile Robot: Preliminary Study

Science.gov (United States)

Baharudin, M. E.; Nor, A. M.; Saad, A. R. M.; Yusof, A. M.

2018-03-01

The motion of vibration-driven robots is based on an internal oscillating mass which can move without legs or wheels. The oscillation of the unbalanced mass by a motor is translated into vibration which in turn produces vertical and horizontal forces. Both vertical and horizontal oscillations are of the same frequency but the phases are shifted. The vertical forces will deflect the bristles which cause the robot to move forward. In this paper, the horizontal motion direction caused by the vertically vibrated bristle is numerically simulated by tuning the frequency of their oscillatory actuation. As a preliminary work, basic equations for a simple off-centered vibration location on the robot platform and simulation model for vibration excitement are introduced. It involves both static and dynamic vibration analysis of robots and analysis of different type of parameters. In addition, the orientation of the bristles and oscillators are also analysed. Results from the numerical integration seem to be in good agreement with those achieved from the literature. The presented numerical integration modeling can be used for designing the bristles and controlling the speed and direction of the robot.

Preliminary Results on Uncertainty Quantification for Pattern Analytics

Energy Technology Data Exchange (ETDEWEB)

Stracuzzi, David John [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Brost, Randolph [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Chen, Maximillian Gene [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Malinas, Rebecca [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Peterson, Matthew Gregor [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Phillips, Cynthia A. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Robinson, David G. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Woodbridge, Diane [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)

2015-09-01

This report summarizes preliminary research into uncertainty quantification for pattern ana- lytics within the context of the Pattern Analytics to Support High-Performance Exploitation and Reasoning (PANTHER) project. The primary focus of PANTHER was to make large quantities of remote sensing data searchable by analysts. The work described in this re- port adds nuance to both the initial data preparation steps and the search process. Search queries are transformed from does the specified pattern exist in the data? to how certain is the system that the returned results match the query? We show example results for both data processing and search, and discuss a number of possible improvements for each.

Preliminary research results for generation and application of high power ion beams on FLASh II accelerator

International Nuclear Information System (INIS)

Yang Hailiang; Qiu Aici; Zhang Jiasheng; He Xiaoping; Sun Jianfeng; Peng Jianchang; Tang Junping; Ren Shuqing; Ouyang Xiaoping; Zhang Guoguang; Huang Jianjun; Yang Li; Wang Haiyang; Li Jingya; Li Hongyu

2004-01-01

Preliminary results for the generation and application of the high power ion beam (HPIB) on the FLASH II accelerator are reported. The structure and principle of the pinch reflex ion beam diode are introduced. The equation of parapotential flow is corrected for the reduction of diode A-K gap due to the motion of cathode and anode plasma. The HPIB peak current of ∼160 kA is obtained with a peak energy of ∼500 keV. Experimental investigations of generating 6-7 MeV quasi-monoenergetic pulsed γ-rays with high power ion (proton) beams striking 19 F target are presented. In addition, the results of the thermal-mechanical effects on the material irradiated with HPIB, which are applied to the simulation of 1 keV black body radiation x-rays, are also discussed

Authentication by Keystroke Timing: Some Preliminary Results

National Research Council Canada - National Science Library

Gaines, R. S; Lisowski, William; Press, S. J; Shapiro, Norman

1980-01-01

... of an individual seeking access to the computer. This report summarizes preliminary efforts to establish whether an individual can be identified by the statistical characteristics of his or her typing...

Preliminary Langmuir probe results on the CTX gun experiment

International Nuclear Information System (INIS)

Tuszewski, M.

1981-12-01

Preliminary results obtained with a double Langmuir probe in the Compact Toroid experiment facility confirm the existence of a gun plasma of n approx. 5 x 10 14 cm -3 and T approx. 10 eV lasting for approx. 250 to 400 μs, which is consistent with interferometry and Thomson scattering data. The probe current characteristics as a function of voltage suggest non-Maxwellian features of the particles distribution functions

Preliminary results of Digital Pulse Shape Acquisition from Chimera

International Nuclear Information System (INIS)

Alderighi, D.M.; Sechi, G.; Anzalone, A.; Cavallaro, S.; Giustolisi, F.; Laguidara, E.; Lanzalone, G.; Porto, F.; Bassini, R.; Boiano, C.; Guazzoni, P.; Russo, S.; Sassi, M.; Zetta, L.; Cardella, G.; Defilippo, S.E.; Lanzano, G.; Paganod, A.; Papa, M.; Pirrone, S.; Politi, G.; Geraci, E.

2003-01-01

A 100 MS/s 14-bit Sampling Analog-to-Digital converter has been used to perform digital pulse-shape acquisition of signals collected from CHIMERA telescopes. The signals from a typical CHIMERA detection cell have been collected using both a standard CHIMERA electronic chain up to the amplifier, and a very simple analog front end, basically reduced to the preamplifier. The preliminary on-beam results are presented. (authors)

Preliminary results of Digital Pulse Shape Acquisition from Chimera

Energy Technology Data Exchange (ETDEWEB)

Alderighi, D.M.; Sechi, G. [INFN Milano and IASF, CNR, Milano (France); Anzalone, A.; Cavallaro, S.; Giustolisi, F.; Laguidara, E.; Lanzalone, G.; Porto, F. [Catania Univ., LNS and Dipartimento di Fisica (France); Bassini, R.; Boiano, C.; Guazzoni, P.; Russo, S.; Sassi, M.; Zetta, L. [Milano Univ., INFN and Dipartimento di Fisica (Italy); Cardella, G.; Defilippo, S.E.; Lanzano, G.; Paganod, A.; Papa, M.; Pirrone, S.; Politi, G. [Catania Univ., INFN and Dipartimento di Fisica (Italy); Geraci, E. [Bologna Univ., INFN and Dipartimento di Fisica (Italy)

2003-07-01

A 100 MS/s 14-bit Sampling Analog-to-Digital converter has been used to perform digital pulse-shape acquisition of signals collected from CHIMERA telescopes. The signals from a typical CHIMERA detection cell have been collected using both a standard CHIMERA electronic chain up to the amplifier, and a very simple analog front end, basically reduced to the preamplifier. The preliminary on-beam results are presented. (authors)

Hellenic Amateur Astronomy Association's activities: Preliminary results on Perseids 2010

Science.gov (United States)

Maravelias, G.

2011-01-01

Preliminary results on the Perseids 2010 are presented. Visual and video observations were obtained by the author and a first reduction of the visual data shows that a maximum of ZHR ~120 was reached during the night 12-13 of August 2010. Moreover, a video setup was tested (DMK camera and UFO Capture v2) and the results show that, under some limitations, valuable data can be obtained.

Functional requirements regarding medical registries--preliminary results.

Science.gov (United States)

Oberbichler, Stefan; Hörbst, Alexander

2013-01-01

The term medical registry is used to reference tools and processes to support clinical or epidemiologic research or provide a data basis for decisions regarding health care policies. In spite of this wide range of applications the term registry and the functional requirements which a registry should support are not clearly defined. This work presents preliminary results of a literature review to discover functional requirements which form a registry. To extract these requirements a set of peer reviewed articles was collected. These set of articles was screened by using methods from qualitative research. Up to now most discovered functional requirements focus on data quality (e. g. prevent transcription error by conducting automatic domain checks).

Strategy for long-term 3D cloud-resolving simulations over the ARM SGP site and preliminary results

Science.gov (United States)

Lin, W.; Liu, Y.; Song, H.; Endo, S.

2011-12-01

Parametric representations of cloud/precipitation processes continue having to be adopted in climate simulations with increasingly higher spatial resolution or with emerging adaptive mesh framework; and it is only becoming more critical that such parameterizations have to be scale aware. Continuous cloud measurements at DOE's ARM sites have provided a strong observational basis for novel cloud parameterization research at various scales. Despite significant progress in our observational ability, there are important cloud-scale physical and dynamical quantities that are either not currently observable or insufficiently sampled. To complement the long-term ARM measurements, we have explored an optimal strategy to carry out long-term 3-D cloud-resolving simulations over the ARM SGP site using Weather Research and Forecasting (WRF) model with multi-domain nesting. The factors that are considered to have important influences on the simulated cloud fields include domain size, spatial resolution, model top, forcing data set, model physics and the growth of model errors. The hydrometeor advection that may play a significant role in hydrological process within the observational domain but is often lacking, and the limitations due to the constraint of domain-wide uniform forcing in conventional cloud system-resolving model simulations, are at least partly accounted for in our approach. Conventional and probabilistic verification approaches are employed first for selected cases to optimize the model's capability of faithfully reproducing the observed mean and statistical distributions of cloud-scale quantities. This then forms the basis of our setup for long-term cloud-resolving simulations over the ARM SGP site. The model results will facilitate parameterization research, as well as understanding and dissecting parameterization deficiencies in climate models.

Preliminary results of a test of a longitudinal phase-space monitor

International Nuclear Information System (INIS)

Kikutani, Eiji; Funakoshi, Yoshihiro; Kawamoto, Takashi; Mimashi, Toshihiro

1994-01-01

A prototype of a longitudinal phase-space monitor has been developed in TRISTAN Main Ring at KEK. The principle of the monitor and its basic components are explained. Also a result of a preliminary beam test is given. (author)

Preliminary Results on Asymptotic Stabilization of Hamiltonian Systems with Nonholonomic Constraints

NARCIS (Netherlands)

Khennouf, H.; Canudas de Wit, C.; Schaft, A.J. van der

1995-01-01

This paper presents some preliminary results on asymptotic stabilization of nonholonomic mechanical systems using the Hamiltonian formulation proposed previously. Our work seeks to establish a general formulation for designing time-varying controllers for some mechanical system described in the

Preliminary Results Of A 600 Joules Small Plasma Focus Device

International Nuclear Information System (INIS)

Lee, S. H.; Yap, S. L.; Wong, C. S.

2009-01-01

Preliminary results of a 600 J (3.7 μF, 18 kV) Mather type plasma focus device operated at low pressure will be presented. The discharge is formed between a solid anode with length of 6 cm and six symmetrically and coaxially arranged cathode rods of same lengths. The cathode base is profiled in a knife-edge design and a set of coaxial plasma gun are attached to it in order to initiate the breakdown and enhance the current sheath formation. The experiments have been performed in argon gas under a low pressure condition of several microbars. The discharge current and the voltage across the electrodes during the discharge are measured with high voltage probe and current coil. The current and voltage characteristics are used to determine the possible range of operating pressure that gives good focusing action. At a narrow pressure regime of 9.0±0.5 μbar, focusing action is observed with good reproducibility. Preliminary result of ion beam energy is presented. More work will be carried out to investigate the radiation output.

77 FR 72817 - Glycine From the People's Republic of China: Preliminary Results of Antidumping Duty...

Science.gov (United States)

2012-12-06

... Republic of China: Preliminary Results of Antidumping Duty Administrative Review and Preliminary Partial... conducting an administrative review of the antidumping duty order on glycine from the People's Republic of... covers one exporter of subject merchandise, Baoding Mantong Fine Chemistry Co. Ltd. (Baoding Mantong). We...

Preliminary results of the round-robin testing of F82H

Energy Technology Data Exchange (ETDEWEB)

Shiba, K.; Yamanouchi, N.; Tohyama, A.

1996-10-01

Preliminary results of metallurgical, physical and mechanical properties of low activation ferritic steel F82H (IEA heat) were obtained in the round-robin test in Japan. The properties of IEA heat F82H were almost the same as the original F82H.

Economic valuation of acidic deposition damages: Preliminary results from the 1985 NAPAP [National Acid Precipitation Assessment Program] damage assessment

International Nuclear Information System (INIS)

Callaway, J.M.; Darwin, R.F.; Nesse, R.J.

1985-01-01

This paper identifies methods used to evaluate the economic damages of acid deposition in the 1985 Damage Assessment being coordinated by the National Acid Precipitation Program. It also presents the preliminary estimates of economic damages for the Assessment. Economic damages are estimated for four effect areas: commercial agriculture and forests, recreational fishing and selected types of materials. In all but the last area, methods are used which incorporate the behavioral responses of individuals and firms or simulated physical damages to resources at risk. The preliminary nature of the estimated damages in each area is emphasized. Over all, the damage estimates should be interpreted with caution. 44 refs., 6 figs., 5 tabs

Assessment of statistical education in Indonesia: Preliminary results and initiation to simulation-based inference

Science.gov (United States)

Saputra, K. V. I.; Cahyadi, L.; Sembiring, U. A.

2018-01-01

Start in this paper, we assess our traditional elementary statistics education and also we introduce elementary statistics with simulation-based inference. To assess our statistical class, we adapt the well-known CAOS (Comprehensive Assessment of Outcomes in Statistics) test that serves as an external measure to assess the student’s basic statistical literacy. This test generally represents as an accepted measure of statistical literacy. We also introduce a new teaching method on elementary statistics class. Different from the traditional elementary statistics course, we will introduce a simulation-based inference method to conduct hypothesis testing. From the literature, it has shown that this new teaching method works very well in increasing student’s understanding of statistics.

Radon concentrations in Norwegian kindergartens: survey planning and preliminary results

International Nuclear Information System (INIS)

Birovljev, A.; Strand, T.; Heiberg, A.

1998-01-01

An extensive radon survey in Norwegian kindergartens and schools was started in early 1997; so far 2481 kindergartens were examined. Preliminary results of the first phase of the survey are presented in tabular and graphic form including, among others, the dependence of average radon concentration on the construction year of the kindergartens and on the age of the buildings. (A.K.)

Preliminary three-dimensional potential flow simulation of a five-liter flask air injection experiment

International Nuclear Information System (INIS)

Davis, J.E.

1977-01-01

The preliminary results of an unsteady three-dimensional potential flow analysis of a five-liter flask air injection experiment (small-scale model simulation of a nuclear reactor steam condensation system) are presented. The location and velocity of the free water surface in the flask as a function of time are determined during pipe venting and bubble expansion processes. The analyses were performed using an extended version of the NASA-Ames Three-Dimensional Potential Flow Analysis System (POTFAN), which uses the vortex lattice singularity method of potential flow analysis. The pressure boundary condition at the free water surface and the boundary condition along the free jet boundary near the pipe exit were ignored for the purposes of the present study. The results of the analysis indicate that large time steps can be taken without significantly reducing the accuracy of the solutions and that the assumption of inviscid flow should not have an appreciable effect on the geometry and velocity of the free water surface. In addition, the computation time required for the solutions was well within acceptable limits

The Southern HII Region Discovery Survey: Preliminary Results

Science.gov (United States)

Shea, Jeanine; Wenger, Trey; Balser, Dana S.; Anderson, Loren D.; Armentrout, William P.; Bania, Thomas M.; Dawson, Joanne; Miller Dickey, John; Jordan, Christopher; McClure-Griffiths, Naomi M.

2017-01-01

HII regions are some of the brightest sources at radio frequencies in the Milky Way and are the sites of massive O and B-type star formation. They have relatively short (Bank Telescope. Candidate HII regions were selected from mid-infrared emission coincident with radio continuum emission, and confirmed as HII regions by the detection of radio recombination lines. Here we discuss the Southern HII Region Discovery Survey (SHRDS), a continuation of the HRDS using the Australia Telescope Compact Array over the Galactic longitude range 230 to 360 degrees. We have reduced and analyzed a small sub-set of the SHRDS sources and discuss preliminary results, including kinematic distances and metallicities.

Preliminary Simulations of CO2 Transport in the Dolostone Formations in the Ordos Basin, China

Energy Technology Data Exchange (ETDEWEB)

Hao, Y; Wolery, T; Carroll, S

2009-04-30

This report summarizes preliminary 2-D reactive-transport simulations on the injection, storage and transport of supercritical CO{sub 2} in dolostone formations in the Ordos Basin in China. The purpose of the simulations was to evaluate the role that basin heterogeneity, permeability, CO{sub 2} flux, and geochemical reactions between the carbonate geology and the CO{sub 2} equilibrated brines have on the evolution of porosity and permeability in the storage reservoir. The 2-D simulation of CO{sub 2} injection at 10{sup 3} ton/year corresponds to CO{sub 2} injection at a rate of 3 x 10{sup 5} ton/year in a 3-D, low permeable rock. An average permeability of 10 md was used in the simulation and reflects the upper range of permeability reported for the Ordos Basin Majiagou Group. Transport and distribution of CO{sub 2} between in the gas, aqueous, and solid phases were followed during a 10-year injection phase and a 10-year post injection phase. Our results show that CO{sub 2} flux and the spatial distribution of reservoir permeability will dictate the transport of CO{sub 2} in the injection and post injection phases. The injection rate of supercritical CO{sub 2} into low permeable reservoirs may need to be adjusted to avoid over pressure and mechanical damage to the reservoir. Although it should be noted that 3-D simulations are needed to more accurately model pressure build-up in the injection phase. There is negligible change in porosity and permeability due to carbonate mineral dissolution or anhydrite precipitation because a very small amount of carbonate dissolution is required to reach equilibrium with respect these phases. Injected CO{sub 2} is stored largely in supercritical and dissolved phases. During the injection phase, CO{sub 2} is transport driven by pressure build up and CO{sub 2} buoyancy.

Nb/NiCu bilayers in single and stacked superconductive tunnel junctions: preliminary results

International Nuclear Information System (INIS)

Pepe, G.P.; Ruotolo, A.; Parlato, L.; Peluso, G.; Ausanio, G.; Carapella, G.; Latempa, R.

2004-01-01

We present preliminary experimental results concerning both single and stacked tunnel junctions in which one of the electrodes was formed by a superconductor/ferromagnet (S/F) bi-layer. In particular, in the stacked configuration a Nb/NiCu bi-layer was used as the intermediate electrode, and it was probed by tunneling on both sides. Tunnel junctions have been characterized in terms of current-voltage characteristics (IVC), and differential conductance. Preliminary steady-state injection-detection measurements performed in the stacked devices at T=4.2 K are also presented and discussed

Long range radio tracking of sea turtles and polar bear: Instrumentation and preliminary results

Science.gov (United States)

Baldwin, H. A.

1972-01-01

Instrumentation developed for studies of path behavior of the green sea turtle and migration movement of polar bear is described. Preliminary results bearing on navigation ability in these species are presented. Both species operate in difficult environments, and the problems faced in the design of electronic instrumentation for these studies are not completely specified at this time. However, the critical factors yet to be understood are primarily related to the behavior of instrumented animals. The data obtained with these experimental techniques are included, first to illustrate the technique and, second to provide initial preliminary results bearing on animal navigation.

Sedimentation on the Valencia Continental Shelf: Preliminary results

Science.gov (United States)

Maldonado, Andres; Swift, Donald J. P.; Young, Robert A.; Han, Gregory; Nittrouer, Charles A.; DeMaster, David J.; Rey, Jorge; Palomo, Carlos; Acosta, Juan; Ballester, A.; Castellvi, J.

1983-10-01

Preliminary analysis of data collected during the course of a cooperative Spanish-United States investigation of the Valencia Shelf (western Mediterranean) reveals a storm-dominated, mud-accumulating sedimentary regime. Calcareous mud is accumulating seaward of a narrow band of shoreface sand and gravel. On the outer shelf the mud is enriched by a pelagic calcareous component. Preliminary 210Pb data from vertical profiles of box cores yield nominal accumulation rates from 2.6 mm y -1 near the Ebro Delta to 1.3 mm y -1 on the southern portion of the Valencia Shelf. Storm-current winnowing has resulted in the development of a biogenic lag sand over the mid-shelf mud in the northern part of the study area. Piston cores reveal a basal Holocene sand and gravel facies similar to that presently seen on the inner shelf. Upward-fining sequences on the central and outer shelf are inferred to result from the landward shift of lithotopes during the course of the Holocene transgression. These sequences are locally repeated, perhaps as the consequence of brief, local interludes of coastal progradation. Application of a diagnostic circulation model suggests that intense, downwelling coastal flows occur during winter northeastern storms. Storm activity has induced erosional shoreface retreat during the course of the Holocene transgression and has generated by this means the basal coarse facies observed in the piston cores. In the central part of the study area seaward of the Albufera Lagoon, the mud blanket thins to a layer several centimeters thick which is draped over a thickened (10 m) basal sand. The basal sand is molded into northwest trending ridges. The data are not sufficient to determine whether these are overstepped barriers, or submarine sand ridges formed by storm flows during the shoreface retreat process.

National Data Center Preparedness Exercise 2015 (NPE 2015): MY-NDC Preliminary Analysis Result

International Nuclear Information System (INIS)

Faisal Izwan Abdul Rashid; Muhammed Zulfakar Zolkaffly

2016-01-01

Malaysia has established the CTBT National Data Centre (MY-NDC) in December 2005. MY-NDC is tasked to perform Comprehensive Nuclear-Test-Ban-Treaty (CTBT) data management as well as provide information for Treaty related events to Nuclear Malaysia as CTBT National Authority. In 2015, MY-NDC has participated in the National Data Centre Preparedness Exercise 2015 (NPE 2015). This paper aims at presenting MY-NDC preliminary analysis result of NPE 2015. In NPE 2015, MY-NDC has performed five different analyses, namely, radionuclide, atmospheric transport modelling (ATM), data fusion, seismic analysis and site forensics. The preliminary findings show the hypothetical scenario in NPE 2015 most probably is an uncontained event resulted high release of radionuclide to the air. (author)

Preliminary Dynamic Feasibility and Analysis of a Spherical, Wind-Driven (Tumbleweed), Martian Rover

Science.gov (United States)

Flick, John J.; Toniolo, Matthew D.

2005-01-01

The process and findings are presented from a preliminary feasibility study examining the dynamics characteristics of a spherical wind-driven (or Tumbleweed) rover, which is intended for exploration of the Martian surface. The results of an initial feasibility study involving several worst-case mobility situations that a Tumbleweed rover might encounter on the surface of Mars are discussed. Additional topics include the evaluation of several commercially available analysis software packages that were examined as possible platforms for the development of a Monte Carlo Tumbleweed mission simulation tool. This evaluation lead to the development of the Mars Tumbleweed Monte Carlo Simulator (or Tumbleweed Simulator) using the Vortex physics software package from CM-Labs, Inc. Discussions regarding the development and evaluation of the Tumbleweed Simulator, as well as the results of a preliminary analysis using the tool are also presented. Finally, a brief conclusions section is presented.

Oil Spill Detection and Modelling: Preliminary Results for the Cercal Accident

Science.gov (United States)

da Costa, R. T.; Azevedo, A.; da Silva, J. C. B.; Oliveira, A.

2013-03-01

two-dimensional surface plume transport model VOILS [1] with the oil spreading formulation enabled. The remaining oil weathering processes (evaporation, emulsification, dispersion and dissolution in the water column) and shoreline retention were disregarded. The computational structure of the model is based on Eulerian-Lagrangian formulations, horizontal unstructured mesh discretization and it is soft-coupled with the tri-dimensional hydrodynamic model SELFE - Semi-Implicit Eulerian Lagrangian Finite Element [15] that uses hybrid sigma-Z coordinates in the vertical. The preliminary results of this hindcast simulation for the Cercal oil spill are presented and compared with available satellite SAR images. The forcings used play an important role in the final results. During the late stage spreading phases of the oil, about one month after the spill, the Douro River outflow is best seen in the SAR images. The morphology of the river outflow is discussed according to traditional coastal dynamics, and compared with model results. In addition to several interesting physical features that were identified, we report on the generation of Internal Solitary Waves (ISW) in the vicinity of the Douro River Plume (DRP). It is well known that trains of short-period internal waves can be generated by river plumes (such as the Columbia River). The internal structure of the observed internal waves (elevation waves or mode-2 versus mode-1 internal waves) is discussed based on the SAR signatures and available stratification. The present work has been conducted under an FCT - Fundaç ão para a Ciência e a Tecnologia / MCTES - Ministério da Ciência, Tecnologia e Ensino Superior (PIDDAC - Programa de Investimentos e Despesas de Desenvolvimento da Administraç ão Central) Portuguese funded project entitled PAC:MAN Pollution accidents in coastal areas: a Risk management system (PTDC/AACAMB/113469/2008).

Mini-DIAL system measurements coupled with multivariate data analysis to identify TIC and TIM simulants: preliminary absorption database analysis

International Nuclear Information System (INIS)

Gaudio, P; Malizia, A; Gelfusa, M; Poggi, L.A.; Martinelli, E.; Di Natale, C.; Bellecci, C.

2017-01-01

Nowadays Toxic Industrial Components (TICs) and Toxic Industrial Materials (TIMs) are one of the most dangerous and diffuse vehicle of contamination in urban and industrial areas. The academic world together with the industrial and military one are working on innovative solutions to monitor the diffusion in atmosphere of such pollutants. In this phase the most common commercial sensors are based on “point detection” technology but it is clear that such instruments cannot satisfy the needs of the smart cities. The new challenge is developing stand-off systems to continuously monitor the atmosphere. Quantum Electronics and Plasma Physics (QEP) research group has a long experience in laser system development and has built two demonstrators based on DIAL (Differential Absorption of Light) technology could be able to identify chemical agents in atmosphere. In this work the authors will present one of those DIAL system, the miniaturized one, together with the preliminary results of an experimental campaign conducted on TICs and TIMs simulants in cell with aim of use the absorption database for the further atmospheric an analysis using the same DIAL system. The experimental results are analysed with standard multivariate data analysis technique as Principal Component Analysis (PCA) to develop a classification model aimed at identifying organic chemical compound in atmosphere. The preliminary results of absorption coefficients of some chemical compound are shown together pre PCA analysis. (paper)

Preliminary Results Of LOCA Problem For APR1400 Reactor

International Nuclear Information System (INIS)

Le Dai Dien; Hoang Minh Giang; Le Thi Thu; Vo Thi Huong; Le Van Hong

2011-01-01

Several features of NPP with APR1400 nuclear reactor during a loss of coolant accident (LOCA) are investigated in this study. The report describes some main design characteristics of an engineering safety systems of APR1400 and the thermal hydraulic calculation results for steady-state using MARS and RELAP/SCDAPSIM codes. Large Break LOCA accident has been analyzed and evaluated based on acceptable criteria for ECCS given by US NRC. The results from cold leg break LOCA with broken area of 0.0465 m 2 in case of high pressure safety injection system (HPSI) failed to operate or 2 and 4 HPSI pumps are activated. The preliminary results of this work is a part of collaboration between INST researchers and KAERI experts in using RELAP tool for safety analysis of NPPs. (author)

Radiolabelling of RC-160: preliminary results

International Nuclear Information System (INIS)

Verdera, E.S.; Balter Binsky, H.S.; Robles, A.M.; Rodriguez, G.; Souto, B.; Laiz, J.; Oliver, P.; Leon, E.

1998-01-01

Vapreotide (RC-160) was labelled with 125 I using Chloramine-T and Iodogen methods and with 99m Tc by a direct method with sodium ditionite as reducing agent in the presence of ascorbic acid. Several methods of purification and quality control were evaluated. Yields of the reactions and of purification steps were calculated. The results obtained for the radioiodination reactions showed higher yields when limiting Chloramine-T method was used. Labelling of RC-160 with 99m Tc indicated better yields when high radioactivity concentration of the radionuclide was used. Stability of the products obtained was assessed at different post-labelling times by selected quality control methods: Sep-Pak cartridge as purification method and chromatography by RP-HPLC and ITLC-SG using saline solution as solvent. It was demonstrated that I-125-RC-160 and Tc-99m-RC-160 were stable during five weeks (at -20 deg. C) and 6 hours (at room temperature) respectively. Preliminary biodistribution of Tc-99m-RC-160 in normal rats and mice were done showing different biological behaviour compared with control animals injected with pertechnetate. In conclusion, RC-160 was successfully labelled with both radionuclides, with radiochemical purity higher than 95%. These results encourage further research work in animal models as well as to investigate the biochemical behaviour of radiolabelled peptide. (author)

Summarizing Simulation Results using Causally-relevant States

Science.gov (United States)

Parikh, Nidhi; Marathe, Madhav; Swarup, Samarth

2016-01-01

As increasingly large-scale multiagent simulations are being implemented, new methods are becoming necessary to make sense of the results of these simulations. Even concisely summarizing the results of a given simulation run is a challenge. Here we pose this as the problem of simulation summarization: how to extract the causally-relevant descriptions of the trajectories of the agents in the simulation. We present a simple algorithm to compress agent trajectories through state space by identifying the state transitions which are relevant to determining the distribution of outcomes at the end of the simulation. We present a toy-example to illustrate the working of the algorithm, and then apply it to a complex simulation of a major disaster in an urban area. PMID:28042620

An experimental apparatus to simulate body-powered prosthetic usage: Development and preliminary evaluation.

Science.gov (United States)

Gao, Fan; Rodriguez, Johanan; Kapp, Susan

2016-06-01

Harness fitting in the body-powered prosthesis remains more art than science due to a lack of consistent and quantitative evaluation. The aim of this study was to develop a mechanical, human-body-shaped apparatus to simulate body-powered upper limb prosthetic usage and evaluate its capability of quantitative examination of harness configuration. The apparatus was built upon a torso of a wooden mannequin and integrated major mechanical joints to simulate terminal device operation. Sensors were used to register cable tension, cable excursion, and grip force simultaneously. The apparatus allowed the scapula to move up to 127 mm laterally and the load cell can measure the cable tension up to 445 N. Our preliminary evaluation highlighted the needs and importance of investigating harness configurations in a systematic and controllable manner. The apparatus allows objective, systematic, and quantitative evaluation of effects of realistic harness configurations and will provide insightful and working knowledge on harness fitting in upper limb amputees using body-powered prosthesis. © The International Society for Prosthetics and Orthotics 2015.

The role of coarse woody debris in southeastern pine forests; preliminary results from a large-scale experiment.

Energy Technology Data Exchange (ETDEWEB)

McCay Timothy, S.; Hanula, James, L.; Loeb, Susan, C.; Lohr, Steven, M.; McMinn, James, W.; Wright-Miley. Bret, D.

2002-08-01

McCay, Timothy S., James L. Hanula, Susan C. Loeb, Steven M. Lohr, James W. McMinn, and Bret D. Wright-Miley. 2002. The role of coarse woody debris in southeastern pine forests; preliminary results from a large-scale experiment. 135-144. In: Proceedings of the symposium on the ecology and management of dead wood in western forests. 1999 November 2-4; Reno, NV. Gen. Tech. Rep. PSW-GTR-181. Albany, CA: Pacific Southwest Research Station, Forest Service, U.S. Department of Agriculture 949 p. ABSTRACT: We initiated a long-term experiment involving manipulation of coarse woody debris (CWD) at the Savannah River National Environmental Research Park in the upper Coastal Plain of South Carolina. Each of four 9.3-ha plots in each of four blocks was subject to one of the following treatments: removal of all snags and fallen logs, removal of fallen logs only, felling and girdling to simulate a catastrophic pulse of CWD, and control. Removal treatments were applied in 1996, and the felling or snag-creation treatment will be applied in 2000-2001. Monitoring of invertebrate, herptile, avian, and mammalian assemblages and CWD dynamics began immediately after CWD removal and continues through the present. Removal treatments resulted in a fivefold to tenfold reduction in CWD abundance. To date, significant differences among treatments have only been detected for a few animal taxa. However, preliminary results underscore the benefits of large-scale experiments. This experiment allowed unambiguous tests of hypotheses regarding the effect of CWD abundance on fauna. Coupled with studies of habitat use and trophic interactions, the experimental approach may result in stronger inferences regarding the function of CWD than results obtained through natural history observation or uncontrolled correlative studies.

The Majorana Demonstrator Status and Preliminary Results

Science.gov (United States)

Yu, C.-H.; Alvis, S. I.; Arnquist, I. J.; Avignone, F. T.; Barabash, A. S.; Barton, C. J.; Bertrand, F. E.; Bode, T.; Brudanin, V.; Busch, M.; Buuck, M.; Caldwell, T. S.; Chan, Y.-D.; Christofferson, C. D.; Chu, P.-H.; Cuesta, C.; Detwiler, J. A.; Dunagan, C.; Efremenko, Yu; Ejiri, H.; Elliott, S. R.; Gilliss, T.; Giovanetti, G. K.; Green, M.; Gruszko, J.; Guinn, I. S.; Guiseppe, V. E.; Haufe, C. R.; Hehn, L.; Henning, R.; Hoppe, E. W.; Howe, M. A.; Keeter, K. J.; Kidd, M. F.; Konovalov, S. I.; Kouzes, R. T.; Lopez, A. M.; Martin, R. D.; Massarczyk, R.; Meijer, S. J.; Mertens, S.; Myslik, J.; Othman, G.; Pettus, W.; Poon, A. W. P.; Radford, D. C.; Rager, J.; Reine, A. L.; Rielage, K.; Ruof, N. W.; Shanks, B.; Shirchenko, M.; Suriano, A. M.; Tedeschi, D.; Varner, R. L.; Vasilyev, S.; Vetter, K.; Vorren, K.; White, B. R.; Wilkerson, J. F.; Wiseman, C.; Xu, W.; Yakushev, E.; Yumatov, V.; Zhitnikov, I.; Zhu, B. Z.

2018-05-01

The MAJORANA Collaboration is using an array of high-purity Ge detectors to search for neutrinoless double-beta decay in 76Ge. Searches for neutrinoless double-beta decay are understood to be the only viable experimental method for testing the Majorana nature of the neutrino. Observation of this decay would imply violation of lepton number, that neutrinos are Majorana in nature, and provide information on the neutrino mass. The MAJORANA DEMONSTRATOR comprises 44.1 kg of p-type point-contact Ge detectors (29.7 kg enriched in 76Ge) surrounded by a low-background shield system. The experiment achieved a high efficiency of converting raw Ge material to detectors and an unprecedented detector energy resolution of 2.5 keV FWHM at Qββ. The MAJORANA collaboration began taking physics data in 2016. This paper summarizes key construction aspects of the Demonstrator and shows preliminary results from initial data.

Barkhausen Effect and Acoustic Emission in a Metallic Glass - Preliminary Results

International Nuclear Information System (INIS)

Lopez Sanchez, R.; Lopez Pumarega, M.I.; Armeite, M.; Piotrkowski, R.; Ruzzante, J.E.

2004-01-01

Magneto Acoustic Emission, which is Barkhausen Noise (BN) and Acoustic Emission (AE), depends on microstructure and existing residual stresses in magnetic materials. Preliminary results obtained by magnetization along two perpendicular directions on a metal glass foil are presented. Signals were analyzed with Statistic, Fast Fourier and Wavelet methods. Results are part of a Joint Research Project of the Faculty of Science, Cantabria University, Spain, and the Elastic Waves Group of the National Atomic Energy Commission, Argentina

Integrated Bio-ISRU and Life Support Systems at the Lunar Outpost: Concept and Preliminary Results

Science.gov (United States)

Brown, I. I.; Garrison, D. H.; Allen, C. C.; Pickering, K.; Sarkisova, S. A.; Galindo, C., Jr.; Pan, D.; Foraker, E.; Mckay, D. S.

2009-01-01

We continue the development of our concept of a biotechnological loop for in-situ resource extraction along with propellant and food production at a future lunar outpost, based on the cultivation of litholytic cyanobacteria (LCB) with lunar regolith (LR) in a geobioreactor energized by sunlight. Our preliminary studies have shown that phototropic cultivation of LCB with simulants of LR in a low-mineralized medium supplemented with CO2 leads to rock dissolution (bioweathering) with the resulting accumulation of Fe, Mg and Al in cyanobacterial cells and in the medium. LCB cultivated with LR simulants produces more O2 than the same organisms cultivated in a high-mineralized medium. The loss of rock mass after bioweathering with LCB suggests the release of O from regolith. Further studies of chemical pathways of released O are required. The bioweathering process is limited by the availability of CO2, N, and P. Since lunar regolith is mainly composed of O, Si, Ca, Al and Mg, we propose to use organic waste to supply a geobioreactor with C, N and P. The recycling of organic waste, including urine, through a geobioreactor will allow for efficient element extraction as well as oxygen and biomass production. The most critical conclusion is that a biological life support system tied to a geobioreactor might be more efficient for supporting an extraterrestrial outpost than a closed environmental system.

Modelled and Observed Diurnal SST Signals: "SSTDV:R.EX.-IM.A.M." Project Preliminary Results

DEFF Research Database (Denmark)

Karagali, Ioanna; Høyer, Jacob; LeBorgne, Pierre

2013-01-01

This study presents some of the preliminary results from the ESA Support To Science Element (STSE) funded project on the Diurnal Variability of the Sea Surface Temperature, regarding its Regional Extend and Implications in Atmospheric Modelling (SSTDV:R.EX.–IM.A.M.). During this phase of the proj......This study presents some of the preliminary results from the ESA Support To Science Element (STSE) funded project on the Diurnal Variability of the Sea Surface Temperature, regarding its Regional Extend and Implications in Atmospheric Modelling (SSTDV:R.EX.–IM.A.M.). During this phase...

Preliminary results of the Spacelab 2 superfluid helium experiment

International Nuclear Information System (INIS)

Mason, P.V.; Collins, D.J.; Elleman, D.D.; Jackson, H.W.; Wang, T.

1986-01-01

An experiment to investigate the properties of superfluid helium in a microgravity environment flew on the Shuttle on the Spacelab 2 mission in July and August of 1985. This paper summarizes the flight experiment and describes some preliminary results. The experiment comprised an investigation of long-wavelength third-sound waves in micron-thick films, a study of the motions of superfluid helium under milli-g and micro-g accelerations, and measurements of the fluctuations in temperature associated with the small motions of the bulk helium. An additional objective was to qualify and characterize a reflyable, space-compatible cryostat

Preliminary results of sequential monitoring of simulated clandestine graves in Colombia, South America, using ground penetrating radar and botany.

Science.gov (United States)

Molina, Carlos Martin; Pringle, Jamie K; Saumett, Miguel; Hernández, Orlando

2015-03-01

In most Latin American countries there are significant numbers of missing people and forced disappearances, 68,000 alone currently in Colombia. Successful detection of shallow buried human remains by forensic search teams is difficult in varying terrain and climates. This research has created three simulated clandestine burial styles at two different depths commonly encountered in Latin America to gain knowledge of optimum forensic geophysics detection techniques. Repeated monitoring of the graves post-burial was undertaken by ground penetrating radar. Radar survey 2D profile results show reasonable detection of ½ clothed pig cadavers up to 19 weeks of burial, with decreasing confidence after this time. Simulated burials using skeletonized human remains were not able to be imaged after 19 weeks of burial, with beheaded and burnt human remains not being able to be detected throughout the survey period. Horizontal radar time slices showed good early results up to 19 weeks of burial as more area was covered and bi-directional surveys were collected, but these decreased in amplitude over time. Deeper burials were all harder to image than shallower ones. Analysis of excavated soil found soil moisture content almost double compared to those reported from temperate climate studies. Vegetation variations over the simulated graves were also noted which would provide promising indicators for grave detection. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Preliminary results of natural radioactivity measurements in the southern part of Ethiopia

International Nuclear Information System (INIS)

Wollel Tiruneh, Getachew; Wodaje Kebede, Worku

2008-01-01

The paper presents the first results of natural radioactivity measurements in the Southern part of Ethiopia (Bale Zone-Oromiya Regional State). The preliminary results indicate that radiation levels in the mining areas of Kallido Mountain are elevated compared with those in the town of Negele Borena (background area). Both external gamma radiation and alpha surface contamination levels are significantly elevated above local background levels

Preliminary results of natural radioactivity measurements in the southern part of Ethiopia

Energy Technology Data Exchange (ETDEWEB)

Wollel Tiruneh, Getachew [Ethiopian Radiation Protection Authority, PO Box 20486 code 1000, Addis-Ababa (Ethiopia)], E-mail: gwollel@yahoo.com; Wodaje Kebede, Worku [Ethiopian Radiation Protection Authority, PO Box 20486 code 1000, Addis-Ababa (Ethiopia)

2008-11-15

The paper presents the first results of natural radioactivity measurements in the Southern part of Ethiopia (Bale Zone-Oromiya Regional State). The preliminary results indicate that radiation levels in the mining areas of Kallido Mountain are elevated compared with those in the town of Negele Borena (background area). Both external gamma radiation and alpha surface contamination levels are significantly elevated above local background levels.

Magnetic resonance imaging of the brain in neonates. Preliminary results

International Nuclear Information System (INIS)

Dumoulin, M.; Legrand, M.; Gremillet, C.; Lecouffe, P.; Rousseau, J.; Pruvo, J.P.; Marchandise, X.

1991-01-01

The place of neonatal cerebral MRI and its specific contribution compared with conventional imaging techniques were evaluated in 36 patients. The difficulties specific to the patient population studied met during this preliminary period are described, with their local solutions. A preliminary evaluation of the diagnostic and prognostic value of MRI according to the disease state and gestational age is presented. The specific contribution of MRI compared with transfontanellar ultrasonography and CT scan is discussed [fr

Investigation of polarized-proton target materials by differential calorimetry: preliminary results

International Nuclear Information System (INIS)

Hill, D.A.; Hill, J.J.

1980-01-01

A simple differential calorimeter was designed and operated for an investigation of the thermodynamic properties of polarized target materials. The calibration and use of the calorimeter are discussed, after a brief exposition of our motivation for this work. The results of a preliminary study of target materials is presented with emphasis on the relevance of the glass state to dynamic polarization in chemically-doped targets

Influence of Boundary Conditions on the Simulation of a Diamond-Type Lattice Structure: A Preliminary Study

Directory of Open Access Journals (Sweden)

Patrick Terriault

2017-01-01

Full Text Available Emergent additive manufacturing processes allow the use of metallic porous structures in various industrial applications. Because these structures comprise a large number of ordered unit cells, their design using conventional modeling approaches, such as finite elements, becomes a real challenge. A homogenization technique, in which the lattice structure is simulated as a fully dense volume having equivalent material properties, can then be employed. To determine these equivalent material properties, numerical simulations can be performed on a single unit cell of the lattice structure. However, a critical aspect to consider is the boundary conditions applied to the external faces of the unit cell. In the literature, different types of boundary conditions are used, but a comparative study is definitely lacking. In this publication, a diamond-type unit cell is studied in compression by applying different boundary conditions. If the porous structure’s boundaries are free to deform, then the periodic boundary condition is found to be the most representative, but constraint equations must be introduced in the model. If, instead, the porous structure is inserted in a rigid enclosure, it is then better to use frictionless boundary conditions. These preliminary results remain to be validated for other types of unit cells loaded beyond the yield limit of the material.

Preliminary Results of the CASCADE Hidden Sector Photon Search

CERN Document Server

Woollett, Nathan; Burt, Graeme; Chattopadhyay, Swapan; Dainton, John; Dexter, Amos; Goudket, Phillipe; Jenkins, Michael; Kalliokoski, Matti; Moss, Andrew; Pattalwar, Shrikant; Thakker, Trina; Williams, Peter

2015-01-01

Light shining through a wall experiments can be used to make measurements of photon-WISP couplings. The first stage of the CASCADE experiment at the Cockcroft Institute of Accelerator Science and Technology is intended to be a proof-of-principle experiment utilising standard microwave technologies to make a modular, cryogenic HSP detector to take advantage of future high-power superconducting cavity tests. In these proceedings we will be presenting the preliminary results of the CASCADE LSW experiment showing a peak expected exclusion of $1.10 \\times 10^{-8}$ in the mass range from 1.96$\\mu$eV to 5.38$\\mu$eV, exceeding current limits.

V and V Efforts of Auroral Precipitation Models: Preliminary Results

Science.gov (United States)

Zheng, Yihua; Kuznetsova, Masha; Rastaetter, Lutz; Hesse, Michael

2011-01-01

Auroral precipitation models have been valuable both in terms of space weather applications and space science research. Yet very limited testing has been performed regarding model performance. A variety of auroral models are available, including empirical models that are parameterized by geomagnetic indices or upstream solar wind conditions, now casting models that are based on satellite observations, or those derived from physics-based, coupled global models. In this presentation, we will show our preliminary results regarding V&V efforts of some of the models.

Ambient Assisted Living and ageing: preliminary results of RITA project.

Science.gov (United States)

Aquilano, Michela; Cavallo, Filippo; Bonaccorsi, Manuele; Esposito, Raffaele; Rovini, Erika; Filippi, Massimo; Esposito, Dario; Dario, Paolo; Carrozza, Maria Chiara

2012-01-01

The ageing of population is a social phenomenon that most of worldwide countries are facing. They are, and will be even more in the future, indeed trying to find solutions for improving quality of life of their elderly citizens. The project RITA wants to demonstrate that an update of the current socio-medical services with an Ambient Assisted Living (AAL) approach could improve the service efficiency and the quality of life of both elderly and caregiver. This paper presents the preliminary results obtained in RITA.

Rainfall assimilation in RAMS by means of the Kuo parameterisation inversion: method and preliminary results

Science.gov (United States)

Orlandi, A.; Ortolani, A.; Meneguzzo, F.; Levizzani, V.; Torricella, F.; Turk, F. J.

2004-03-01

In order to improve high-resolution forecasts, a specific method for assimilating rainfall rates into the Regional Atmospheric Modelling System model has been developed. It is based on the inversion of the Kuo convective parameterisation scheme. A nudging technique is applied to 'gently' increase with time the weight of the estimated precipitation in the assimilation process. A rough but manageable technique is explained to estimate the partition of convective precipitation from stratiform one, without requiring any ancillary measurement. The method is general purpose, but it is tuned for geostationary satellite rainfall estimation assimilation. Preliminary results are presented and discussed, both through totally simulated experiments and through experiments assimilating real satellite-based precipitation observations. For every case study, Rainfall data are computed with a rapid update satellite precipitation estimation algorithm based on IR and MW satellite observations. This research was carried out in the framework of the EURAINSAT project (an EC research project co-funded by the Energy, Environment and Sustainable Development Programme within the topic 'Development of generic Earth observation technologies', Contract number EVG1-2000-00030).

PRELIMINARY COUPLING OF THE MONTE CARLO CODE OPENMC AND THE MULTIPHYSICS OBJECT-ORIENTED SIMULATION ENVIRONMENT (MOOSE) FOR ANALYZING DOPPLER FEEDBACK IN MONTE CARLO SIMULATIONS

Energy Technology Data Exchange (ETDEWEB)

Matthew Ellis; Derek Gaston; Benoit Forget; Kord Smith

2011-07-01

In recent years the use of Monte Carlo methods for modeling reactors has become feasible due to the increasing availability of massively parallel computer systems. One of the primary challenges yet to be fully resolved, however, is the efficient and accurate inclusion of multiphysics feedback in Monte Carlo simulations. The research in this paper presents a preliminary coupling of the open source Monte Carlo code OpenMC with the open source Multiphysics Object-Oriented Simulation Environment (MOOSE). The coupling of OpenMC and MOOSE will be used to investigate efficient and accurate numerical methods needed to include multiphysics feedback in Monte Carlo codes. An investigation into the sensitivity of Doppler feedback to fuel temperature approximations using a two dimensional 17x17 PWR fuel assembly is presented in this paper. The results show a functioning multiphysics coupling between OpenMC and MOOSE. The coupling utilizes Functional Expansion Tallies to accurately and efficiently transfer pin power distributions tallied in OpenMC to unstructured finite element meshes used in MOOSE. The two dimensional PWR fuel assembly case also demonstrates that for a simplified model the pin-by-pin doppler feedback can be adequately replicated by scaling a representative pin based on pin relative powers.

Preliminary test results and CFD analysis for moderator circulation test at Korea

Energy Technology Data Exchange (ETDEWEB)

Kim, H.T. [Korea Atomic Energy Research Inst., Daejeon (Korea, Republic of); Im, S.H.; Sung, H.J. [Korea Advanced Inst. of Science and Tech., Daejeon (Korea, Republic of); Seo, H.; Bang, I.C. [Ulsan National Inst. of Science and Tech., Ulsan (Korea, Republic of)

2014-07-01

Korea Atomic Energy Research Institute (KAERI) is carrying out a scaled-down moderator test program to simulate the CANDU6 moderator circulation phenomena during steady state operation and accident conditions. This research program includes the construction of the Moderator Circulation Test (MCT) facility, production of the validation data for self-reliant CFD tools, and development of optical measurement system using the Particle Image Velocimetry (PIV). The MCT facility includes a primary circulation loop (pipe lines, a primary side pump, a heat exchanger, valves, flow meters) and a secondary side loop (pipe lines, a secondary side pump, and an external cooling tower). The loop leakage test and non-heating test are performed in the present work. In the present work the PIV technique is used to measure the velocity distributions in the scaled moderator tank of MCT under iso-thermal test conditions. The preliminary PIV measurement data are obtained and compared with CFX code predictions. (author)

Preliminary test results and CFD analysis for moderator circulation test at Korea

International Nuclear Information System (INIS)

Kim, H.T.; Im, S.H.; Sung, H.J.; Seo, H.; Bang, I.C.

2014-01-01

Korea Atomic Energy Research Institute (KAERI) is carrying out a scaled-down moderator test program to simulate the CANDU6 moderator circulation phenomena during steady state operation and accident conditions. This research program includes the construction of the Moderator Circulation Test (MCT) facility, production of the validation data for self-reliant CFD tools, and development of optical measurement system using the Particle Image Velocimetry (PIV). The MCT facility includes a primary circulation loop (pipe lines, a primary side pump, a heat exchanger, valves, flow meters) and a secondary side loop (pipe lines, a secondary side pump, and an external cooling tower). The loop leakage test and non-heating test are performed in the present work. In the present work the PIV technique is used to measure the velocity distributions in the scaled moderator tank of MCT under iso-thermal test conditions. The preliminary PIV measurement data are obtained and compared with CFX code predictions. (author)

BRIDGE - Behavioural reaching interfaces during daily antigravity activities through upper limb exoskeleton: Preliminary results.

Science.gov (United States)

Gandolla, Marta; Costa, Andrea; Aquilante, Lorenzo; Gfoehler, Margit; Puchinger, Markus; Braghin, Francesco; Pedrocchi, Alessandra

2017-07-01

People with neuromuscular diseases such as muscular dystrophy experience a distributed and evolutive weakness in the whole body. Recent technological developments have changed the daily life of disabled people strongly improving the perceived quality of life, mostly concentrating on powered wheelchairs, so to assure autonomous mobility and respiratory assistance, essential for survival. The key concept of the BRIDGE project is to contrast the everyday experience of losing functions by providing them of a system able to exploit the best their own residual capabilities in arm movements so to keep them functional and autonomous as much as possible. BRIDGE is composed by a light, wearable and powered five degrees of freedom upper limb exoskeleton under the direct control of the user through a joystick or gaze control. An inverse kinematic model allows to determine joints position so to track patient desired hand position. BRIDGE prototype has been successfully tested in simulation environment, and by a small group of healthy volunteers. Preliminary results show a good tracking performance of the implemented control scheme. The interaction procedure was easy to understand, and the interaction with the system was successful.

Preliminary 2D design study for A ampersand PCT

International Nuclear Information System (INIS)

Keto, E.; Azevedo, S.; Roberson, P.

1995-03-01

Lawrence Livermore National Laboratory is currently designing and constructing a tomographic scanner to obtain the most accurate possible assays of radioactivity in barrels of nuclear waste in a limited amount of time. This study demonstrates a method to explore different designs using laboratory experiments and numerical simulations. In particular, we examine the trade-off between spatial resolution and signal-to-noise. The simulations are conducted in two dimensions as a preliminary study for three dimensional imaging. We find that the optimal design is entirely dependent on the expected source sizes and activities. For nuclear waste barrels, preliminary results indicate that collimators with widths of 1 to 3 inch and aspect ratios of 5:1 to 10:1 should perform well. This type of study will be repeated in 3D in more detail to optimize the final design

DECOMPOSITION OF TARS IN MICROWAVE PLASMA – PRELIMINARY RESULTS

Directory of Open Access Journals (Sweden)

Mateusz Wnukowski

2014-07-01

Full Text Available The paper refers to the main problem connected with biomass gasification - a presence of tar in a product gas. This paper presents preliminary results of tar decomposition in a microwave plasma reactor. It gives a basic insight into the construction and work of the plasma reactor. During the experiment, researches were carried out on toluene as a tar surrogate. As a carrier gas for toluene and as a plasma agent, nitrogen was used. Flow rates of the gases and the microwave generator’s power were constant during the whole experiment. Results of the experiment showed that the decomposition process of toluene was effective because the decomposition efficiency attained above 95%. The main products of tar decomposition were light hydrocarbons and soot. The article also gives plans for further research in a matter of tar removal from the product gas.

The demand factors for cesareans in Portugal – some preliminary results

OpenAIRE

Tavares, Aida Isabel; Rocha, Tania

2012-01-01

The aim of this work is to determine the demand factors for cesareans in Portugal. This work is exploratory and preliminary. Data is aggregated in NUTSII , for the period 2002-10. The number of cesareans performed is count data which requires the estimation of this panel data by a negative binomial with fixed effects. The main result is the evidence that there may be induced demand for cesareans in Portugal. Further research is needed.

Preliminary results on the Arecibo Pisces-Perseus Supercluster Survey

Science.gov (United States)

Cortes, Rosemary; Lebron, Mayra; Jones, Michael G.; Koopmann, Rebecca A.; Haynes, Martha P.; APPSS Team, Undergraduate ALFALFA Team, and the ALFALFA Team

2018-01-01

The Arecibo Pisces-Perseus Supercluster Survey (APPSS) aims to exploit the Baryonic Tully-Fisher Relation to derive distances and peculiar velocities of galaxies in and near the main ridge of the Pisces-Perseus Supercluster (PPS), one of the most prominent features of the Cosmic Web in the nearby Universe. The sample of galaxies contains ~ 600 sources in the low-mass range (8 Team institutions in which each group contributes to the analysis of a subset of the HI PPS data. In this poster, we will present the contributions of the U.P.R. team to the APPSS project. We will show the procedure used for the Arecibo HI data analysis, including some examples, and will show our preliminary results.

SU-C-204-06: Monte Carlo Dose Calculation for Kilovoltage X-Ray-Psoralen Activated Cancer Therapy (X-PACT): Preliminary Results

Energy Technology Data Exchange (ETDEWEB)

Mein, S [Duke University Medical Physics Graduate Program (United States); Gunasingha, R [Department of Radiation Safety, Duke University Medical Center (United States); Nolan, M [Department of Clinical Sciences, College of Veterinary Medicine, North Carolina State University (United States); Oldham, M; Adamson, J [Department of Radiation Oncology, Duke University Medical Center (United States)

2016-06-15

Purpose: X-PACT is an experimental cancer therapy where kV x-rays are used to photo-activate anti-cancer therapeutics through phosphor intermediaries (phosphors that absorb x-rays and re-radiate as UV light). Clinical trials in pet dogs are currently underway (NC State College of Veterinary Medicine) and an essential component is the ability to model the kV dose in these dogs. Here we report the commissioning and characterization of a Monte Carlo (MC) treatment planning simulation tool to calculate X-PACT radiation doses in canine trials. Methods: FLUKA multi-particle MC simulation package was used to simulate a standard X-PACT radiation treatment beam of 80kVp with the Varian OBI x-ray source geometry. The beam quality was verified by comparing measured and simulated attenuation of the beam by various thicknesses of aluminum (2–4.6 mm) under narrow beam conditions (HVL). The beam parameters at commissioning were then corroborated using MC, characterized and verified with empirically collected commissioning data, including: percent depth dose curves (PDD), back-scatter factors (BSF), collimator scatter factor(s), and heel effect, etc. All simulations were conducted for N=30M histories at M=100 iterations. Results: HVL and PDD simulation data agreed with an average percent error of 2.42%±0.33 and 6.03%±1.58, respectively. The mean square error (MSE) values for HVL and PDD (0.07% and 0.50%) were low, as expected; however, longer simulations are required to validate convergence to the expected values. Qualitatively, pre- and post-filtration source spectra matched well with 80kVp references generated via SPEKTR software. Further validation of commissioning data simulation is underway in preparation for first-time 3D dose calculations with canine CBCT data. Conclusion: We have prepared a Monte Carlo simulation capable of accurate dose calculation for use with ongoing X-PACT canine clinical trials. Preliminary results show good agreement with measured data and hold

Preliminary results of MR imaging of lymphoma: Distinguishing active tumor from benign residue

International Nuclear Information System (INIS)

Drace, J.; Baker, L.L.; Chang, P.; Castellino, R.A.

1987-01-01

Distinguishing tumor from benign posttreatment tissue based on both morphologic and tissue characteristics is critically important. Patients are studied before, during, and after treatment; at the time of recurrence; and on long-term follow-up. Multisection spin-echo sequences in orthogonal planes and a special single-section tissue characterization matrix of 16 different repetition time/echo time combinations are used. These basic images are used for cluster analysis (approximate fuzzy C means), T1-T2 synthetic images, linear combinations, and comparison with internal standards. Preliminary results in 35 patients imaged before treatment and 12 patients with follow-up examinations consistently show lymphoma masses to have complex architecture with high T2-weighted signal and moderate T1-weighted signal, distinct from posttreatment fibrosis. Uncommon components of active tumor with low T2-weighted signal appear distinct from fibrosis on T1-weighted images. Preliminary cluster analysis results show distinct clustering of active lymphoma versus fibrosis and biopsy-proved cystic degeneration

Dissolved air flotation for treating wastewater of the nuclear industry. Preliminary results

International Nuclear Information System (INIS)

Ortiz-Oliveros, H.B.; Jimenez-Moleon, M.C.; Cruz-Gonzalez, D.

2012-01-01

Preliminary testing of dissolved air flotation (DAF) for wastewater treatment is presented. A combined coagulation-flocculation/DAF column system is used to remove oil and 60 Co from nuclear industry wastewater. In this work, operational conditions and coagulant/flocculant concentrations are optimized by varying pH. Determinations of air-solids ratio (G/S), retention time (θ), pressure (P), volume of depressurized air-water mixture (V), turbidity and 60 Co concentrations are reported. The effect of the treatment on the efficiency of separation of oily residues is also discussed. The results establish that the coagulant/flocculant system, formed by a modified polyamine (25 mgL -1 ) and a slightly cationic polyacrylamide (1.5 mgL -1 ), under specific operational conditions (pH = 7, mixing intensity Im 1 = 300 s -1 and Im 2 = 30 s -1 ), allowed the destabilization of colloidal matter, resulting in resistant flocs. It was concluded that by using G/S = 0.3, θ = 15 min, P = 620 kPa and V = 0.0012 m 3 , the greatest percentage removals of oil, turbidity, total cobalt and 60 Co were obtained. These preliminary results then show that dissolved air flotation represents a good alternative for treatment of nuclear industry wastewater contaminated with radionuclides. (author)

The RPC-based IFR system at BaBar experiment: preliminary results

International Nuclear Information System (INIS)

Piccolo, Davide; Palano, A.; Bagnasco, S.; Buzzo, A.; Contri, R.; Crosetti, G.; Lo Vetere, M.; Macri, M.; Monge, R.; Passaggio, S.; Patrignani, C.; Robutti, E.; Santroni, A.; Anulli, F.; Baldini, R.; Calcaterra, A.; De Sangro, R.; Falciai, D.; Finocchiaro, G.; Patteri, P.; Peruzzi, I.; Piccolo, M.; Yu, Z.; Zallo, A.; Cavallo, N.; De Nardo, G.; Fabozzi, F.; Gatto, C.; Lista, L.; Paolucci, P.; Sciacca, C.; Bionta, R.; Wright, D.; Band, H.; Johnson, J.

2002-01-01

The IFR system is a RPC-based detector used to identify muons and neutral hadrons in the BaBar experiment at PEP II machine in SLAC. The RPC system can be used to reconstruct the trajectory of muons, pions and neutral hadrons interacting in the iron of the IFR. The different range and hit pattern allow to discriminate different particles crossing the IFR. An overview of the system design and the preliminary results on the IFR performances are reported

The RPC-based IFR system at BaBar experiment preliminary results

CERN Document Server

Piccolo, D; Bagnasco, S; Baldini, R; Band, H R; Bionta, R; Buzzo, A; Calcaterra, A; Cavallo, N; Contri, R; Crosetti, G; De Nardo, Gallieno; De Sangro, R; Fabozzi, F; Falciai, D; Finocchiaro, G; Gatto, C; Johnson, J; Lista, L; Lo Vetere, M; Macri, M; Monge, R; Palano, A; Paolucci, P; Passaggio, S; Patrignani, C; Patteri, P; Peruzzi, I; Piccolo, M; Robutti, E; Santroni, A; Sciacca, C; Wright, D; Yu, Z; Zallo, A

2002-01-01

The IFR system is a RPC-based detector used to identify muons and neutral hadrons in the BaBar experiment at PEP II machine in SLAC. The RPC system can be used to reconstruct the trajectory of muons, pions and neutral hadrons interacting in the iron of the IFR. The different range and hit pattern allow to discriminate different particles crossing the IFR. An overview of the system design and the preliminary results on the IFR performances are reported.

KEEP Reading Research 1974: Overall Strategy and Preliminary Results. Technical Report No. 23.

Science.gov (United States)

Tharp, Roland G.; And Others

Reading research is an important aspect of the Kamehameha Early Education Program. This report describes the overall strategy of the reading research program, which is based on a conceptual framework that divides lines of inquiry into motivation, linguistics, instructional procedures, and correlational analysis. Preliminary results for each of…

Preliminary results on laboratory simulations of the decomposition of the green algae Ulva rigida

International Nuclear Information System (INIS)

Karavoltsos, S.; Scoullous, M.; Kaberi, H.

1999-01-01

The Ulva Rigida is a cosmopolitan green algae characteristic of many eutrophic and mesotrophic coastal environments. The effect of its growth and decomposition on the cycle of trace metals has been studied by using enclosures in the site Loutropyrgos over a number of years. The present study is a continuation of that research. Its main aim was to simulate a number of the field experiments in the laboratory, under more controlled conditions and understand better the impact of the decomposition of algae on sea water and sediment

Escherichia coli O26 IN RAW BUFFALO MILK: PRELIMINARY RESULTS

Directory of Open Access Journals (Sweden)

A. Rella

2013-02-01

Full Text Available Escherichia coli O26 is considered to be one of the most important food-borne pathogen. In this study, 120 buffalo milk samples collected in Lazio and in Apulia regions were tested for the presence of E. coli O26. One buffalo milk sample (0,8% tested positive for E. coli O26; the isolate was positive at the verocytotoxicity test and it showed resistance properties to different antimicrobial classes. These preliminary results highlight the need to monitor the foods of animal origin used for production and eaten by a wide range of persons, respect VTEC organism.

Modeling fluid flow and heat transfer at Basin and Range faults: preliminary results for Leach hot springs, Nevada

Science.gov (United States)

López, Dina L.; Smith, Leslie; Storey, Michael L.; Nielson, Dennis L.

1994-01-01

The hydrothermal systems of the Basin and Range Province are often located at or near major range bounding normal faults. The flow of fluid and energy at these faults is affected by the advective transfer of heat and fluid from an to the adjacent mountain ranges and valleys, This paper addresses the effect of the exchange of fluid and energy between the country rock, the valley fill sediments, and the fault zone, on the fluid and heat flow regimes at the fault plane. For comparative purposes, the conditions simulated are patterned on Leach Hot Springs in southern Grass Valley, Nevada. Our simulations indicated that convection can exist at the fault plane even when the fault is exchanging significant heat and fluid with the surrounding country rock and valley fill sediments. The temperature at the base of the fault decreased with increasing permeability of the country rock. Higher groundwater discharge from the fault and lower temperatures at the base of the fault are favored by high country rock permabilities and fault transmissivities. Preliminary results suggest that basal temperatures and flow rates for Leach Hot Springs can not be simulated with a fault 3 km deep and an average regional heat flow of 150 mW/m2 because the basal temperature and mass discharge rates are too low. A fault permeable to greater depths or a higher regional heat flow may be indicated for these springs.

Waste conditioning for tank heel transfer. Preliminary data and results

International Nuclear Information System (INIS)

Ebadian, M.A.

1999-01-01

This report summarizes the research carried out at Florida International University's Hemispheric Center for Environmental Technology (FIU-HCET) for the fiscal year 1998 (FY98) under the Tank Focus Area (TFA) project ''Waste Conditioning for Tank Slurry Transfer.'' The objective of this project is to determine the effect of chemical and physical properties on the waste conditioning process and transfer. The focus of this research consisted in building a waste conditioning experimental facility to test different slurry simulants under different conditions, and analyzing their chemical and physical properties. This investigation would provide experimental data and analysis results that can make the tank waste conditioning process more efficient, improve the transfer system, and influence future modifications to the waste conditioning and transfer system. A waste conditioning experimental facility was built in order to test slurry simulants. The facility consists of a slurry vessel with several accessories for parameter control and sampling. The vessel also has a lid system with a shaft-mounted propeller connected to an air motor. In addition, a circulation system is connected to the slurry vessel for simulant cooling and heating. Experimental data collection and analysis of the chemical and physical properties of the tank slurry simulants has been emphasized. For this, one waste slurry simulant (Fernald) was developed, and another two simulants (SRS and Hanford) obtained from DOE sites were used. These simulants, composed of water, soluble metal salts, and insoluble solid particles, were used to represent the actual radioactive waste slurries from different DOE sites. The simulants' chemical and physical properties analyzed include density, viscosity, pH, settling rate, and volubility. These analyses were done to samples obtained from different experiments performed at room temperature but different mixing time and strength. The experimental results indicate that the

Preliminary results from the MINERvA experiment

International Nuclear Information System (INIS)

Harris, Deborah A.

2011-01-01

The MINERvA experiment, operating since 2009 in the NuMI neutrino beam line at Fermilab, has collected neutrino and antineutrino scattering data on a variety of nuclear targets. The detector is designed to identify events originating in plastic scintillator, lead, carbon, iron, water, and liquid helium. The goal of the experiment is to measure inclusive and exclusive cross sections for neutrino and antineutrino with much greater precision than previous experiments. We present preliminary kinematic distributions for charged current quasi-elastic scattering and other processes.

Preliminary reactive geochemical transport simulation study on CO2 geological sequestration at the Changhua Coastal Industrial Park Site, Taiwan

Science.gov (United States)

Sung, R.; Li, M.

2013-12-01

assumed throughout the simulation domain. Comparisons among simulated results with different mesh systems of nested meshes and non-nested meshes and considerations of multiphase reactive transport and physical transport were demonstrated in this study. Preliminary results of injection CO2 for 50 years are: (1) about 7 wt.% of injected CO2 was trapped as carbonate minerals mainly as ankerite; (2) porosities were decreased by 0.014 % and increased by 0.102 % at the injection point and beneath the cap rock, respectively, and were subsequently decreased with time due to minerals precipitation mostly as illite and ankerite; (3) differences of simulated aquifer responses between reactive transport and physical transport were insignificant; and (4) projected CO2 plumes with the nested meshes was smaller than those by the non-nested meshes after cease of CO2 injection. Keywords: CO2-Saline-Mineral Interaction, Reactive Geochemical Transport, TOUGHREACT, Mineral Trapping Assessment, Changhua Costal Industrial Park Site, Taiwan Reference: Marini, L., 2006, Geological Sequestration of Carbon Dioxide, Volume 11: Thermodynamics, Kinetics, and Reaction Path Modeling, Elsevier Science, pp.470. Xu, T., J. A. Apps and K. Pruess, 2004, Numerical simulation of CO2 disposal by mineral trapping in deep aquifers, Applied Geochemistry, Vol. 19:917-936.

Vivo dosimetry using TLD detectors in prostate seed implants of I-125: preliminary results

International Nuclear Information System (INIS)

Sanchez-Reyes, A.; Pedro, A.; Bassas, P.; Duch, M. A.; Cros, M.; Mane, S.

2011-01-01

We present preliminary results of a new in vivo dosimetry technique that could allow to know immediately after implantation of the prostate if the dose distribution determined by the scheduler is similar to the actual dose measured with TLD detectors.

77 FR 66580 - Certain Preserved Mushrooms From India: Preliminary Results of Antidumping Duty Administrative...

Science.gov (United States)

2012-11-06

... DEPARTMENT OF COMMERCE International Trade Administration [A-533-813] Certain Preserved Mushrooms... preserved mushrooms (mushrooms) from India. The period of review (POR) is February 1, 2011, through January... Preliminary Results of Antidumping Duty Administrative Review: Certain Preserved Mushrooms from India...

Electron-cloud simulation results for the SPS and recent results for the LHC

International Nuclear Information System (INIS)

Furman, M.A.; Pivi, M.T.F.

2002-01-01

We present an update of computer simulation results for some features of the electron cloud at the Large Hadron Collider (LHC) and recent simulation results for the Super Proton Synchrotron (SPS). We focus on the sensitivity of the power deposition on the LHC beam screen to the emitted electron spectrum, which we study by means of a refined secondary electron (SE) emission model recently included in our simulation code

Chemical Analysis of the Moon at the Surveyor VII Landing Site: Preliminary Results.

Science.gov (United States)

Turkevich, A L; Franzgrote, E J; Patterson, J H

1968-10-04

The alpha-scattering experiment aboard Surveyor VII has provided a chemical analysis of the moon in the area of the crater Tycho. The preliminary results indicate a chemical composition similar to that already found at two mare sites, but with a lower concentration of elements of the iron group (titanium through copper).

Aerosol composition in a stagnant air mass impacted by dense fogs: preliminary results

Energy Technology Data Exchange (ETDEWEB)

Jacob, D.J.; Munger, J.W.; Waldman, J.M.; Hoffman, M.R.

1984-01-01

Over the last two winters, our research group has been investigating the chemical composition of fogwater and haze aerosol during wintertime stagnation episodes in the San Joaquin Valley of California. The valley is encompassed by mountain ranges. During the winter a strong subsidence inversion based below the natural boundaries of the valley restricts the ventilation of the air masses below the inversion. The residence time of an air parcel in the valley under these stagnation conditions is on the order of 8 days. Because the trapped air is very humid, stagnation episodes are associated with a persistent thick haze and frequent widespread nighttime fogs. During the winter 1982-1983 the authors sampled fog and haze at one site (Bakersfield); results from this preliminary study have been discussed in detail in a previous report. In the winter 1983-1984 the scale of the program was expanded in order to test hypotheses formulated as a result of first year data. The present paper first reports briefly on the 1982-1983 results and outlines the essential conclusions. They then describe the large-scale experiment conducted during the winter of 1983-1984, and discuss some preliminary fogwater data.

Vapour explosions (fuel-coolant interactions) resulting from the sub-surface injection of water into molten metals: preliminary results

International Nuclear Information System (INIS)

Asher, R.C.; Bullen, D.; Davies, D.

1976-03-01

Preliminary experiments are reported on the relationship between the injection mode of contact and the occurrence and magnitude of vapour explosions. Water was injected beneath the surface of molten metals, chiefly tin at 250 to 900 0 C. Vapour explosions occurred in many, but not all, cases. The results are compared with Dullforce's observations (Culham Report (CLM-P424) on the dropping mode of contact and it appears that rather different behaviour is found; in particular, the present results suggest that the Temperature Interaction Zone is different for the two modes of contact. (author)

A Qualitative Study of Factors Influencing Racial Diversity in Environmental Education: Preliminary Results

Science.gov (United States)

Kathy James; Leo H. McAvoy

1992-01-01

This study presents preliminary result interviews with people of color working in environmental education and interpretation throughout the United States. The three primary questions asked were these? (1) What path led each individual to a career in environmental education; (2) How does each individual define environmentalism? and (3) What are the primary issues this...

Radiation Testing on State-of-the-Art CMOS: Challenges, Plans, and Preliminary Results

Science.gov (United States)

LaBel, Kenneth A.; Cohn, Lewis M.

2009-01-01

At GOMAC 2007 and 2008, we discussed a variety of challenges for radiation testing of modern semiconductor devices and technologies [1, 2]. In this presentation, we provide more specific details in this on-going investigation focusing on out-of-the-box lessons observed for providing radiation effects assurances as well as preliminary test results.

Ares-I-X Vehicle Preliminary Range Safety Malfunction Turn Analysis

Science.gov (United States)

Beaty, James R.; Starr, Brett R.; Gowan, John W., Jr.

2008-01-01

Ares-I-X is the designation given to the flight test version of the Ares-I rocket (also known as the Crew Launch Vehicle - CLV) being developed by NASA. As part of the preliminary flight plan approval process for the test vehicle, a range safety malfunction turn analysis was performed to support the launch area risk assessment and vehicle destruct criteria development processes. Several vehicle failure scenarios were identified which could cause the vehicle trajectory to deviate from its normal flight path, and the effects of these failures were evaluated with an Ares-I-X 6 degrees-of-freedom (6-DOF) digital simulation, using the Program to Optimize Simulated Trajectories Version 2 (POST2) simulation framework. The Ares-I-X simulation analysis provides output files containing vehicle state information, which are used by other risk assessment and vehicle debris trajectory simulation tools to determine the risk to personnel and facilities in the vicinity of the launch area at Kennedy Space Center (KSC), and to develop the vehicle destruct criteria used by the flight test range safety officer. The simulation analysis approach used for this study is described, including descriptions of the failure modes which were considered and the underlying assumptions and ground rules of the study, and preliminary results are presented, determined by analysis of the trajectory deviation of the failure cases, compared with the expected vehicle trajectory.

Combined Observational and Modeling Efforts to Better Understand Aerosol-Cloud-Precipitation Interactions Over Land: Preliminary Results from 7-SEAS/BASELInE 2013

Science.gov (United States)

Loftus, Adrian M.; Tsay, Si-Chee

2015-01-01

This talk presents some of the detailed observations of low-level stratocumulus over northern Vietnam during 7-SEASBASELInE 2013 by SMARTLabs' ACHIEVE W-band cloud radar and other remote sensing instruments. These observations are the first of their kind for this region and will aid in ongoing studies of biomass-burning aerosol impacts on local and regional weather and climate. Preliminary results from simulations using the Goddard Cumulus Ensemble (GCE) with recently implemented triple-moment bulk microphysics to examine the sensitivity of low-level stratocumulus over land to aerosols are also presented. Recommendations for future observational activities in the 7-SEAS northern region in collaboration with international partners will also be discussed.

Chemical Analysis of the Moon at the Surveyor VI Landing Site: Preliminary Results.

Science.gov (United States)

Turkevich, A L; Patterson, J H; Franzgrote, E J

1968-06-07

The alpha-scattering experiment aboard soft-landing Surveyor VI has provided a chemical analysis of the surface of the moon in Sinus Medii. The preliminary results indicate that, within experimental errors, the composition is the same as that found by Surveyor V in Mare Tranquillitatis. This finding suggests that large portions of the lunar maria resemble basalt in composition.

Small-angle neutron scattering investigations of Co-doped iron oxide nanoparticles. Preliminary results

Science.gov (United States)

Creanga, Dorina; Balasoiu, Maria; Soloviov, Dmitro; Balasoiu-Gaina, Alexandra-Maria; Puscasu, Emil; Lupu, Nicoleta; Stan, Cristina

2018-03-01

Preliminary small-angle neutron scattering investigations on aqueous suspensions of several cobalt doped ferrites (CoxFe3-xO4, x=0; 0.5; 1) nanoparticles prepared by chemical co-precipitation method, are reported. The measurements were accomplished at the YuMO instrument in function at the IBR-2 reactor. Results of intermediary data treatment are presented and discussed.

Preliminary results of a battery-based, multi megawatt 200 kA pulsed power supply.

NARCIS (Netherlands)

Karthaus, W.; Kolkert, W.J.; Nowee, J.

1989-01-01

A pulsed power supply consisting of a fast discharge battery, a switch based on silicon-controlled-rectifier SCR technology, and an energy storage/pulse transformer is discussed. Preliminary results indicate that the battery is capable of discharging current pulses with reproducible peak values of

78 FR 28192 - Polyethylene Retail Carrier Bags From Thailand: Preliminary Results of Antidumping Duty...

Science.gov (United States)

2013-05-14

... Bags From Thailand: Preliminary Results of Antidumping Duty Administrative Review; 2011-2012 AGENCY... on polyethylene retail carrier bags (PRCBs) from Thailand. The review covers 11 respondents. The... merchandise has been sold at less than normal value by the companies subject to this review. DATES: Effective...

Simulation of synchrotron motion with rf noise

International Nuclear Information System (INIS)

Leemann, B.T.; Forest, E.; Chattopadhyay, S.

1986-08-01

The theoretical formulation is described that is behind an algorithm for synchrotron phase-space tracking with rf noise and some preliminary simulation results of bunch diffusion under rf noise obtained by actual tracking

Preliminary results on tests of a Cerenkov ring imaging device employing a photoionizing PWC

Energy Technology Data Exchange (ETDEWEB)

Durkin, S.; Honma, A.; Leith, D.W.G.S.

1978-08-01

A brief description of techniques and problems of ring imaging Cerenkov detectors employing photoionizing PWC's is discussed. Preliminary results on a one dimensional ring imaging device tested at SLAC in May and June of 1978 are then presented. These results include rough measurements of the Cerenkov ring in nitrogen, argon, neon, and helium produced by a collimated positron beam.

1995 Integrated Monitoring Study: Fog measurements in the Northern San Joaquin Valley - preliminary results

Energy Technology Data Exchange (ETDEWEB)

Collett, J. Jr.; Bator, A.; Sherman, D.E. [Colorado State Univ., Fort Collins, CO (United States)] [and others

1996-12-31

Vertical gradients in fog chemistry and physics were measured from a 430 m television broadcast tower in the northern San Joaquin Valley near Walnut Grove, California. Fog was collected on the ground and at two elevations on the tower using Caltech Active Strand Cloudwater Collectors Version 2 (CASCC2). Work was conducted as part of the 1995 Integrated Monitoring Study (IMS95). Results will be used to evaluate the need to make measurements aloft in future regional studies of fog processing of atmospheric particles and for testing whether vertically resolved fog models provide realistic simulations of fog physics and chemistry above the ground. Two fog/low cloud events were sampled during the tower study. Preliminary results show concentrations of major species in the fogwater typically decreasing with altitude, while liquid water contents increase. Fogwater loadings of major species, the total amount of a species in the aqueous phase per unit air volume, were observed to increase with altitude. Major species concentrations were typically quite stable at a given elevation, while significant decreases were observed over time in liquid water content. Fogwater concentrations of soluble hydroperoxides were highest near the surface and increased with time after sunrise and were observed to coexist in the high pH fog with S(IV). Time lapse video footage of the top of the fog/cloud layer revealed a very dynamic interface, suggesting entrainment of material from the clear air into the fog/cloud may be significant. 12 refs., 7 figs.

Development of the GOSAT-2 FTS-2 Simulator and Preliminary Sensitivity Analysis for CO2 Retrieval

Science.gov (United States)

Kamei, A.; Yoshida, Y.; Dupuy, E.; Hiraki, K.; Yokota, Y.; Oishi, Y.; Murakami, K.; Morino, I.; Matsunaga, T.

2013-12-01

The Greenhouse Gases Observing Satellite-2 (GOSAT-2), which is a successor mission to the GOSAT, is planned to be launched in FY 2017. The Fourier Transform Spectrometer-2 (FTS-2) onboard the GOSAT-2 is a primary sensor to observe infrared light reflected and emitted from the Earth's surface and atmosphere. The FTS-2 obtains high-spectral resolution spectra with four bands from near to short-wavelength infrared (SWIR) region and one band in the thermal infrared (TIR) region. The column amounts of carbon dioxide (CO2) and methane (CH4) are retrieved from the obtained radiance spectra with SWIR bands. Compared to the FTS onboard the GOSAT, the FTS-2 includes an additional SWIR band to allow for carbon monoxide (CO) measurement. We have been developing a tool, named GOSAT-2 FTS-2 simulator, which is capable of simulating the spectral radiance data observed by the FTS-2 using the Pstar2 radiative transfer code. The purpose of the GOSAT-2 FTS-2 simulator is to obtain data which is exploited in the sensor specification, the optimization of parameters for Level 1 processing, and the improvement of Level 2 algorithms. The GOSAT-2 FTS-2 simulator, composed of the six components: 1) Overall control, 2) Onboarding platform, 3) Spectral radiance calculation, 4) Fourier transform, 5) L1B processing, and 6) L1B data output, has been installed on the GOSAT Research Computation Facility (GOSAT RCF), which is a large-scale, high-performance, and energy-efficient computer. We present the progress in the development of the GOSAT-2 FTS-2 simulator and the preliminary sensitivity analysis, relating to the engineering parameters, the aerosols and clouds, and so on, on the Level 1 processing for CO2 retrieval from the obtained data by simulating the FTS-2 SWIR observation using the GOSAT-2 FTS-2 simulator.

Comparison Of Simulation Results When Using Two Different Methods For Mold Creation In Moldflow Simulation

Directory of Open Access Journals (Sweden)

Kaushikbhai C. Parmar

2017-04-01

Full Text Available Simulation gives different results when using different methods for the same simulation. Autodesk Moldflow Simulation software provide two different facilities for creating mold for the simulation of injection molding process. Mold can be created inside the Moldflow or it can be imported as CAD file. The aim of this paper is to study the difference in the simulation results like mold temperature part temperature deflection in different direction time for the simulation and coolant temperature for this two different methods.

Impact of climate changes on management plans for the St. Francois and Aylmer reservoirs : preliminary results

International Nuclear Information System (INIS)

Turcotte, R.; Fortin, L.G.; Pugin, S.; Cyr, J.F.; Picard, F.; Poirier, C.; Lacombe, P.

2004-01-01

Dams used for flood control, water supply, recreational activities and hydroelectricity in the province of Quebec are managed by the Centre d'Expertise Hydrique du Quebec (CEHQ). This paper addressed the issue of global warming and the changes that may occur in the hydrological regime within the next decades in response to predicted changes in climate. As a result of the changes in hydrological regime, there is a risk of losing the equilibrium between various objectives, identifiable through water management plans. The CEHQ is conducting a pilot study for the Saint-Francois and Aylmer reservoirs in order to develop a method to evaluate the adaptability of current management plans to climate change. The project is based on potential climate change scenarios as well as on deterministic and distributed hydrological models. Daily time steps are used to evaluate the hydrological impacts of climate change. CEHQ has developed a model that simulates the use of current management plans. The model makes it possible to evaluate and compare the occurrences where stream flows and water levels exceed critical values. The effectiveness of the management plans in both current and climate change scenarios can thereby be evaluated. Preliminary results suggest a possible increase in flood risk and fewer low water level occurrences. 18 refs., 4 tabs., 12 figs

Hybrid Spectral Micro-CT: System Design, Implementation, and Preliminary Results

CERN Document Server

Bennett, James R; Xu, Qiong; Yu, Hengyong; Walsh, Michael; Butler, Anthony; Butler, Phillip; Cao, Guohua; Mohs, Aaron; Wang, Ge

2014-01-01

Spectral CT has proven an important development in biomedical imaging, and there have been several publications in the past years demonstrating its merits in pre-clinical and clinical applications. In 2012, Xu et al. reported that near-term implementation of spectral micro-CT could be enhanced by a hybrid architecture: a narrow-beam spectral "interior" imaging chain integrated with a traditional wide-beam "global" imaging chain. This hybrid integration coupled with compressive sensing (CS)-based interior tomography demonstrated promising results for improved contrast resolution, and decreased system cost and radiation dose. The motivation for the current study is implementation and evaluation of the hybrid architecture with a first-of-its-kind hybrid spectral micro-CT system. Preliminary results confirm improvements in both contrast and spatial resolution. This technology is shown to merit further investigation and potential application in future spectral CT scanner design.

A biogeochemical model of Lake Pusiano (North Italy and its use in the predictability of phytoplankton blooms: first preliminary results

Directory of Open Access Journals (Sweden)

Alessandro OGGIONI

2006-02-01

Full Text Available This study reports the first preliminary results of the DYRESM-CAEDYM model application to a mid size sub-alpine lake (Lake Pusiano North Italy. The in-lake modelling is a part of a more general project called Pusiano Integrated Lake/Catchment project (PILE whose final goal is to understand the hydrological and trophic relationship between lake and catchment, supporting the restoration plan of the lake through field data analysis and numerical models. DYRESM is a 1D-3D hydrodynamics model for predicting the vertical profile of temperature, salinity and density. CAEDYM is multi-component ecological model, used here as a phytoplankton-zooplankton processes based model, which includes algorithms to simulate the nutrient cycles within the water column as well as the air-water gas exchanges and the water-sediments fluxes. The first results of the hydrodynamics simulations underline the capability of the model to accurately simulate the surface temperature seasonal trend and the thermal gradient whereas, during summer stratification, the model underestimates the bottom temperature of around 2 °C. The ecological model describes the epilimnetic reactive phosphorus (PO4 depletion (due to the phytoplankton uptake and the increase in PO4 concentrations in the deepest layers of the lake (due to the mineralization processes and the sediments release. In terms of phytoplankton dynamics the model accounts for the Planktothrix rubescens dominance during the whole season, whereas it seems to underestimate the peak in primary production related to both the simulated algal groups (P. rubescens and the rest of the other species aggregated in a single class. The future aims of the project are to complete the model parameterization and to connect the in-lake and the catchment modelling in order to gain an integrated view of the lake-catchment ecosystem as well as to develop a three dimensional model of the lake.

Approach to the fracture hydrology at Stripa: preliminary results

International Nuclear Information System (INIS)

Gale, J.E.; Witherspoon, P.A.

1979-05-01

There are two main problems associated with the concept of geologic storage of radioactive waste in fractured crystalline rock: (1) the thermo-mechanical effects of the heat generated by the waste, and (2) the potential for transport of radioactive materials by the groundwater system. In both problems, fractures play a dominant role. An assessment of the hydraulic and mechanical characteristics of fractued rock requires a careful series of laboratory and field investigations. The complexity of the problem is illustrated by the field studies in a fractured granite that are currently underway in an abandoned iron-ore mine at Stripa, Sweden. Much information is being gathered from an extensive series of boreholes and fracture maps. The approach being taken to integrate these data into an analysis of the fracture hydrology is reviewed and preliminary results from the hydrology program are presented. 13 figures

Preliminary Results Of PCA On MRO CRISM Multispectral Images

Science.gov (United States)

Klassen, David R.; Smith, M. D.

2008-09-01

Mars Reconnaissance Orbiter arrived at Mars in March 2006 and by September had achieved its science-phase orbit with the Compact Reconnaissance Imaging Spectrometer for Mars (CRISM) beginning its visible to near-infrared (VIS/NIR) spectral imaging shortly thereafter. One of the goals of CRISM is to fill in the spatial gaps between the various targeted observations, eventually mapping the entire surface. Due to the large volume of data this would create, the instrument works in a reduced spectral sampling mode creating "multispectral” images. From this data we can create image cubes using 70 wavelengths from 0.410 to 3.504 µm. We present here a preliminary analysis of these multispectral mode data products using the technique of Principal Components Analysis. Previous work with ground-based images has shown that over an entire visible hemisphere, there are only three to four meaningful components out of 32-105 wavelengths over 1.5-4.1 µm. The first two of these components are fairly consistent over all time intervals from day-to-day and season-to-season. [1-4] The preliminary work on the CRISM images cubes implies similar results_three to four significant principal components that are fairly consistent over time. We will show these components and a rough linear mixture modeling based on in-data spectral endmembers derived from the extrema of the principal components [5]. References: [1] Klassen, D. R. and Bell III, J. F. (2001) BAAS 33, 1069. [2] Klassen, D. R. and Bell III, J. F. (2003) BAAS, 35, 936. [3] Klassen, D. R., Wark, T. J., Cugliotta, C. G. (2005) BAAS, 37, 693. [4] Klassen, D. R. and Bell III, J. F. (2007) in preparation. [5] Klassen, D. R. and Bell III, J. F. (2000) BAAS, 32, 1105.

Preliminary results of a feasibility study for a hard x-ray Kirkpatrick-Baez telescope

DEFF Research Database (Denmark)

Joensen, Karsten D.; Gorenstein, Paul; Wood, James L.

1994-01-01

the preliminary results of a feasibility study of a multifocus Kirkpatrick-Baez telescope. We conclude that high quality multilayers can be performed on relevant thin large flat substrate with adequate uniformity, and that existing deposition chambers can produce the multilayers at a rate of 0.42 m2 per day, so...

Jovian seismology: preliminary results of the SYMPA instrument

Science.gov (United States)

Gaulme, P.; Schmider, F. X.; Gay, J.; Jacob, C.; Jeanneaux, F.; Alvarez, M.; Reyes, M.; Valtier, J. C.; Fossat, E.; Palle, P. L.; Belmonte, J. C.; Gelly, B.

2006-06-01

Jupiter's internal structure is poorly known (Guillot et al. 2004). Seismology is a powerful tool to investigate the internal structure of planets and stars, by analyzing how acoustic waves propagate. Mosser (1997) and Gudkova & Zarkhov (1999) showed that the detection and the identification of non-radial modes up to degree ℓ=25 can constrain strongly the internal structure. SYMPA is a ground-based network project dedicated to the Jovian oscillations (Schmider et al. 2002). The instrument is composed of a Mach-Zehnder interferometer producing four interferograms of the planetary spectrum. The combination of the four images in phase quadrature allows the reconstruction of the incident light phase, which is related to the Doppler shift generated by the oscillations. Two SYMPA instruments were built at the Nice university and were used simultaneously during two observation campaigns, in 2004 and 2005, at the San Pedro Martir observatory (Mexico) and the Teide observatory (Las Canarias). We will present for the first time the data processing and the preliminary results of the experiment.

SPANISH MULTICENTRIC STUDY ABOUT NUTRITION-INFLAMATIONhn WITH MID DILUTION (ENIMID STUDY: PRELIMINARY RESULTS

Directory of Open Access Journals (Sweden)

Barril G

2012-06-01

CONCLUSIONS: 1-The preliminary results show that MidDilution provides a good removal of small and middle molecules, increases appetite by providing a proper balance of cytokines through stimulation of antiinflamatory ones and neuropeptide Y. 2-It provides an improvement of body composition. Finally MidDilution improves nutritional parameters which leads to a better quality of life, as well as physical and mental status.

Preliminary results from the Orbiting Solar Observatory 8 - Observations of optically thin lines

Science.gov (United States)

Shine, R. A.; Roussel-Dupre, D.; Bruner, E. C., Jr.; Chipman, E. G.; Lites, B. W.; Rottman, G. J.; Athay, R. G.; White, O. R.

1976-01-01

The University of Colorado spectrometer aboard OSO 8 has measured the high temperature C IV resonance lines (at 1548 and 1551 A) and the Si IV resonance lines (at 1393 and 1402 A) formed in the solar chromosphere-corona transition region. Preliminary results include studies of mean profiles, a comparison of cell and network profiles, and the behavior of the lines at the extreme solar limb.

Preliminary results from a study of the double beta decay of 150Nd

International Nuclear Information System (INIS)

Perillo, I.M.C.; Chan, Y.D.; Hurley, D.; Lesko, K.T.; McDonald, R.J.; Moorhead, M.E.; Norman, E.B.; Smith, A.R.; Stokstad, R.G.

1996-01-01

We report the preliminary results from a study of the double beta decay of 150 Nd to the first 0 + excited state of 150 Sm. Our data consists of 50 days of counting 5 kg of natural Nd 2 O 3 at the LBNL-Oroville low background facility. The deduced lower limit for the half life of this decay mode is 4.9.10 19 years. (orig.)

76 FR 26247 - Magnesium Metal From the Russian Federation: Preliminary Results of Antidumping Duty...

Science.gov (United States)

2011-05-06

... to represent the total net realizable value (NRV) of raw magnesium, it used this value as the offset... AVISMA did not make sales to the United States at less than normal value. If these preliminary results... Than Fair Value: Pure Magnesium in Granular Form From the People's Republic of China, 66 FR 49345...

Observations of Phobos by the Mars Express radar MARSIS: Description of the detection techniques and preliminary results

Science.gov (United States)

Cicchetti, A.; Nenna, C.; Plaut, J. J.; Plettemeier, D.; Noschese, R.; Cartacci, M.; Orosei, R.

2017-11-01

The Mars Advanced Radar for Subsurface and Ionosphere Sounding (MARSIS) (Picardi et al., 2005) is a synthetic aperture low frequency radar altimeter, onboard the ESA Mars Express orbiter, launched in June 2003. It is the first and so far the only spaceborne radar that has observed the Martian moon Phobos. Radar echoes were collected on different flyby trajectories. The primary aim of sounding Phobos is to prove the feasibility of deep sounding, into its subsurface. MARSIS is optimized for deep penetration investigations and is capable of transmitting at four different bands between 1.3 MHz and 5.5 MHz with a 1 MHz bandwidth. Unfortunately the instrument was originally designed to operate exclusively on Mars, assuming that Phobos would not be observed. Following this assumption, a protection mechanism was implemented in the hardware (HW) to maintain a minimum time separation between transmission and reception phases of the radar. This limitation does not have any impact on Mars observation but it prevented the observation of Phobos. In order to successfully operate the instrument at Phobos, a particular configuration of the MARSIS onboard software (SW) parameters, called ;Range Ambiguity,; was implemented to override the HW protection zone, ensuring at the same time a high level of safety of the instrument. This paper describes the principles of MARSIS onboard processing, and the procedure through which the parameters of the processing software were tuned to observe targets below the minimum distance allowed by hardware. Some preliminary results of data analysis will be shown, with the support of radar echo simulations. A qualitative comparison between the simulated results and the actual data, does not support the detection of subsurface reflectors.

Preliminary irradiation test results from the Yankee Atomic Electric Company reactor vessel test irradiation program

International Nuclear Information System (INIS)

Biemiller, E.C.; Fyfitch, S.; Campbell, C.A.

1993-01-01

The Yankee Atomic Electric Company test irradiation program was implemented to characterize the irradiation response of representative Yankee Rowe reactor vessel beltline plate materials and to remove uncertainties in the analysis of existing irradiation data on the Yankee Rowe reactor vessel steel. Plate materials each containing 0.24 w/o copper, but different nickel contents at 0.63 w/o and 0.19 w/o, were heat treated to simulate the Yankee vessel heat treatment (austenitized at 1800 deg F) and to simulate Regulatory Guide 1.99 database materials (austenitized at 1600 deg. F). These heat treatments produced different microstructures so the effect of microstructure on irradiation damage sensitivity could be tested. Because the nickel content of the test plates varied and the copper level was constant, the effect of nickel on irradiation embrittlement was also tested. Correlation monitor material, HSST-02, was included in the program to benchmark the Ford Nuclear Reactor (U. of Michigan Test Reactor) which had never been used for this type of irradiation program. Materials taken from plate surface locations (vs. 1/4T) were included to test whether or not the improved toughness properties of the plate surface layer, resulting from the rapid quench, is maintained after irradiation. If the improved properties are maintained, pressurized thermal shock calculations could utilize this margin. Finally, for one experiment, irradiations were conducted at two irradiation temperatures (500 deg. F and 550 deg. F) to determine the effect of irradiation temperature on embrittlement. The preliminary results of the irradiation program show an increase in T 30 shift of 69 deg. F for a decrease in irradiation temperature of 50 deg. F. The results suggest that for nickel bearing steels, the superior toughness of plate surface material is maintained after irradiation and for the copper content tested, nickel had no apparent effect on irradiation response. No apparent microstructure

Preliminary closed Brayton cycle study for a space reactor application

International Nuclear Information System (INIS)

Guimaraes, Lamartine Nogueira Frutuoso; Carvalho, Ricardo Pinto de; Camillo, Giannino Ponchio

2007-01-01

The Nuclear Energy Division (ENU) of the Institute for Advanced Studies (IEAv) has started a preliminary design study for a Closed Brayton Cycle Loop (CBCL) aimed at a space reactor application. The main objectives of the study are to establish a starting concept for the CBCL components specifications, and to develop a demonstrative simulator of CBCL in nominal operation conditions. The ENU/IEAv preliminary design study is developing the CBCL around the NOELLE 60290 turbo machine. The actual nuclear reactor study is being conducted independently. Because of that, a conventional heat source is being used for the CBCL, in this preliminary design phase. This paper describes the steady state simulator of the CBCL operating with NOELLE 60290 turbo machine. In principle, several gases are being considered as working fluid, as for instance: air, helium, nitrogen, CO2 and gas mixtures such as helium and xenon. At this moment the simulator is running with Helium as the working fluid. Simplified models of heat and mass transfer are being developed to simulate thermal components. Future efforts will focus on keeping track of the modifications being implemented at the NOELLE 60290 turbo machine in order to build the CBCL. (author)

Preliminary closed Brayton cycle study for a space reactor application

Energy Technology Data Exchange (ETDEWEB)

Guimaraes, Lamartine Nogueira Frutuoso; Carvalho, Ricardo Pinto de [Institute for Advanced Studies, Sao Jose dos Campos, SP (Brazil)]. E-mail: guimarae@ieav.cta.br; Camillo, Giannino Ponchio [Instituto Tecnologico de Aeronautica (ITA), Sao Jose dos Campos, SP (Brazil)]. E-mail: gianninocamillo@gmail.com

2007-07-01

The Nuclear Energy Division (ENU) of the Institute for Advanced Studies (IEAv) has started a preliminary design study for a Closed Brayton Cycle Loop (CBCL) aimed at a space reactor application. The main objectives of the study are to establish a starting concept for the CBCL components specifications, and to develop a demonstrative simulator of CBCL in nominal operation conditions. The ENU/IEAv preliminary design study is developing the CBCL around the NOELLE 60290 turbo machine. The actual nuclear reactor study is being conducted independently. Because of that, a conventional heat source is being used for the CBCL, in this preliminary design phase. This paper describes the steady state simulator of the CBCL operating with NOELLE 60290 turbo machine. In principle, several gases are being considered as working fluid, as for instance: air, helium, nitrogen, CO2 and gas mixtures such as helium and xenon. At this moment the simulator is running with Helium as the working fluid. Simplified models of heat and mass transfer are being developed to simulate thermal components. Future efforts will focus on keeping track of the modifications being implemented at the NOELLE 60290 turbo machine in order to build the CBCL. (author)

Thermo-hydro-mechanical simulation of a 3D fractured porous rock: preliminary study of coupled matrix-fracture hydraulics

International Nuclear Information System (INIS)

Canamon, I.; Javier Elorza, F.; Ababou, R.

2007-01-01

We present a problem involving the modeling of coupled flow and elastic strain in a 3D fractured porous rock, which requires prior homogenization (up-scaling) of the fractured medium into an equivalent Darcian anisotropic continuum. The governing equations form a system of PDE's (Partial Differential Equations) and, depending on the case being considered, this system may involve two different types of 'couplings' (in a real system, both couplings (1) and (2) generally take place): 1) Hydraulic coupling in a single (no exchange) or in a dual matrix-fracture continuum (exchange); 2) Thermo-Hydro-Mechanical interactions between fluid flow, pressure, elastic stress, strain, and temperature. We present here a preliminary model and simulation results with FEMLAB R , for the hydraulic problem with anisotropic heterogeneous coefficients. The model is based on data collected at an instrumented granitic site (FEBEX project) for studying a hypothetical nuclear waste repository at the Grimsel Test Site in the Swiss Alps. (authors)

Thermo-hydro-mechanical simulation of a 3D fractured porous rock: preliminary study of coupled matrix-fracture hydraulics

Energy Technology Data Exchange (ETDEWEB)

Canamon, I.; Javier Elorza, F. [Universidad Politecnica de Madrid, Dept. de Matematica Aplicada y Metodos Informaticas, ETSI Minas (UPM) (Spain); Ababou, R. [Institut de Mecanique des Fluides de Toulouse (IMFT), 31 (France)

2007-07-01

We present a problem involving the modeling of coupled flow and elastic strain in a 3D fractured porous rock, which requires prior homogenization (up-scaling) of the fractured medium into an equivalent Darcian anisotropic continuum. The governing equations form a system of PDE's (Partial Differential Equations) and, depending on the case being considered, this system may involve two different types of 'couplings' (in a real system, both couplings (1) and (2) generally take place): 1) Hydraulic coupling in a single (no exchange) or in a dual matrix-fracture continuum (exchange); 2) Thermo-Hydro-Mechanical interactions between fluid flow, pressure, elastic stress, strain, and temperature. We present here a preliminary model and simulation results with FEMLAB{sup R}, for the hydraulic problem with anisotropic heterogeneous coefficients. The model is based on data collected at an instrumented granitic site (FEBEX project) for studying a hypothetical nuclear waste repository at the Grimsel Test Site in the Swiss Alps. (authors)

Modelling Extortion Racket Systems: Preliminary Results

Science.gov (United States)

Nardin, Luis G.; Andrighetto, Giulia; Székely, Áron; Conte, Rosaria

Mafias are highly powerful and deeply entrenched organised criminal groups that cause both economic and social damage. Overcoming, or at least limiting, their harmful effects is a societally beneficial objective, which renders its dynamics understanding an objective of both scientific and political interests. We propose an agent-based simulation model aimed at understanding how independent and combined effects of legal and social norm-based processes help to counter mafias. Our results show that legal processes are effective in directly countering mafias by reducing their activities and changing the behaviour of the rest of population, yet they are not able to change people's mind-set that renders the change fragile. When combined with social norm-based processes, however, people's mind-set shifts towards a culture of legality rendering the observed behaviour resilient to change.

Particle simulations in toroidal geometry

International Nuclear Information System (INIS)

Aydemir, A.Y.

1992-09-01

A computational tool to be used in kinetic simulations of toroidal plasmas is being developed. The initial goal of the project is to develop an electrostatic gyrokinetic model for studying transport and stability problems in tokamaks. In this brief report, preliminary results from the early stages of this effort are presented

Predicting Tropical Cyclogenesis with a Global Mesoscale Model: Preliminary Results with Very Severe Cyclonic Storm Nargis (2008)

Science.gov (United States)

Shen, B.; Tao, W.; Atlas, R.

2008-12-01

Very Severe Cyclonic Storm Nargis, the deadliest named tropical cyclone (TC) in the North Indian Ocean Basin, devastated Burma (Myanmar) in May 2008, causing tremendous damage and numerous fatalities. An increased lead time in the prediction of TC Nargis would have increased the warning time and may therefore have saved lives and reduced economic damage. Recent advances in high-resolution global models and supercomputers have shown the potential for improving TC track and intensity forecasts, presumably by improving multi-scale simulations. The key but challenging questions to be answered include: (1) if and how realistic, in terms of timing, location and TC general structure, the global mesoscale model (GMM) can simulate TC genesis and (2) under what conditions can the model extend the lead time of TC genesis forecasts. In this study, we focus on genesis prediction for TCs in the Indian Ocean with the GMM. Preliminary real-data simulations show that the initial formation and intensity variations of TC Nargis can be realistically predicted at a lead time of up to 5 days. These simulations also suggest that the accurate representations of a westerly wind burst (WWB) and an equatorial trough, associated with monsoon circulations and/or a Madden-Julian Oscillation (MJO), are important for predicting the formation of this kind of TC. In addition to the WWB and equatorial trough, other favorable environmental conditions will be examined, which include enhanced monsoonal circulation, upper-level outflow, low- and middle-level moistening, and surface fluxes.

The evaluation of GL impact in Physical sciences using bibliometric indicators : preliminary results

OpenAIRE

Di Cesare, Rosa (CNR); GreyNet, Grey Literature Network Service

1994-01-01

A bibliometric study of the Italian grey literature in SIGLE database. Preliminary results. Given the increasing importance of Grey Literature (GL) for the information and documentation field, it is essential to apply a bibliometric analysis similar to the one widely used for the conventional literature. Study objectives: 1) impact evalutation of grey literature in physical sciences; and 2) differentiation between scientific and non scientific grey literature documents in the same discipline,...

Preliminary Results for the OECD/NEA Time Dependent Benchmark using Rattlesnake, Rattlesnake-IQS and TDKENO

Energy Technology Data Exchange (ETDEWEB)

DeHart, Mark D. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Mausolff, Zander [Univ. of Florida, Gainesville, FL (United States); Weems, Zach [Univ. of Florida, Gainesville, FL (United States); Popp, Dustin [Univ. of Florida, Gainesville, FL (United States); Smith, Kristin [Univ. of Florida, Gainesville, FL (United States); Shriver, Forrest [Univ. of Florida, Gainesville, FL (United States); Goluoglu, Sedat [Univ. of Florida, Gainesville, FL (United States); Prince, Zachary [Texas A & M Univ., College Station, TX (United States); Ragusa, Jean [Texas A & M Univ., College Station, TX (United States)

2016-08-01

One goal of the MAMMOTH M&S project is to validate the analysis capabilities within MAMMOTH. Historical data has shown limited value for validation of full three-dimensional (3D) multi-physics methods. Initial analysis considered the TREAT startup minimum critical core and one of the startup transient tests. At present, validation is focusing on measurements taken during the M8CAL test calibration series. These exercises will valuable in preliminary assessment of the ability of MAMMOTH to perform coupled multi-physics calculations; calculations performed to date are being used to validate the neutron transport solver Rattlesnake\\cite{Rattlesnake} and the fuels performance code BISON. Other validation projects outside of TREAT are available for single-physics benchmarking. Because the transient solution capability of Rattlesnake is one of the key attributes that makes it unique for TREAT transient simulations, validation of the transient solution of Rattlesnake using other time dependent kinetics benchmarks has considerable value. The Nuclear Energy Agency (NEA) of the Organization for Economic Cooperation and Development (OECD) has recently developed a computational benchmark for transient simulations. This benchmark considered both two-dimensional (2D) and 3D configurations for a total number of 26 different transients. All are negative reactivity insertions, typically returning to the critical state after some time.

Preliminary Results for the OECD/NEA Time Dependent Benchmark using Rattlesnake, Rattlesnake-IQS and TDKENO

International Nuclear Information System (INIS)

DeHart, Mark D.; Mausolff, Zander; Weems, Zach; Popp, Dustin; Smith, Kristin; Shriver, Forrest; Goluoglu, Sedat; Prince, Zachary; Ragusa, Jean

2016-01-01

One goal of the MAMMOTH M&S project is to validate the analysis capabilities within MAMMOTH. Historical data has shown limited value for validation of full three-dimensional (3D) multi-physics methods. Initial analysis considered the TREAT startup minimum critical core and one of the startup transient tests. At present, validation is focusing on measurements taken during the M8CAL test calibration series. These exercises will valuable in preliminary assessment of the ability of MAMMOTH to perform coupled multi-physics calculations; calculations performed to date are being used to validate the neutron transport solver Rattlesnake\\citelesnake) and the fuels performance code BISON. Other validation projects outside of TREAT are available for single-physics benchmarking. Because the transient solution capability of Rattlesnake is one of the key attributes that makes it unique for TREAT transient simulations, validation of the transient solution of Rattlesnake using other time dependent kinetics benchmarks has considerable value. The Nuclear Energy Agency (NEA) of the Organization for Economic Cooperation and Development (OECD) has recently developed a computational benchmark for transient simulations. This benchmark considered both two-dimensional (2D) and 3D configurations for a total number of 26 different transients. All are negative reactivity insertions, typically returning to the critical state after some time.

78 FR 7395 - Stainless Steel Bar From India: Preliminary Results of Antidumping Duty Administrative Review...

Science.gov (United States)

2013-02-01

... DEPARTMENT OF COMMERCE International Trade Administration [A-533-810] Stainless Steel Bar From... steel bar (SSB) from India. The period of review (POR) is February 1, 2011, through January 31, 2012... Preliminary Results of Antidumping Duty Administrative Review: Stainless Steel Bar from India'' dated...

Preliminary experimental results from a linear reciprocating magnetic refrigerator prototype

International Nuclear Information System (INIS)

Tagliafico, Luca Antonio; Scarpa, Federico; Valsuani, Federico; Tagliafico, Giulio

2013-01-01

A linear reciprocating magnetic refrigerator prototype was designed and built with the aid of an industrial partner. The refrigerator is based on the Active Magnetic Regenerative cycle, and exploits two regenerators working in parallel. The active material is Gadolinium in plates, 0.8 mm thick, for a total mass of 0.36 kg. The device is described and results about magnetic field and temperature span measurements are presented. The designed permanent magnet structure, based on an improved cross-type arrangement, generates a maximum magnetic field intensity of 1.55 T in air, over a gap of (13 × 50 × 100) mm 3 . The maximum temperature span achieved is 5.0 K, in a free run condition. -- Highlights: ► We give preliminary results from a linear reciprocating magnetic refrigerator prototype. ► The design is intended to process visualization and investigation. ► The prototype behavior gives us various suggestions to improve its general performance

Archaeogeophysical investigations in Tiwanaku: preliminary results

Science.gov (United States)

Masini, Nicola; Sileo, Maria; Lasaponara, Rosa; Leucci, Giovanni; Orefici, Giuseppe; Rizzo, Enzo

2017-04-01

-1450) Tiwanaku was characterized by the resurgence of regional identities and polities In spite of the rich archaeological record numerous issues, related to the function and the extension of Tiwanaku, need to be investigated especially in the monumental core which includes the pyramid of Akapana, and other ceremonial places such Kalasasaya, Putuni and Kantatallita. To this aims some geophysical investigations were performed in 2009 and 2014 in the context of multidisciplinary research including the use of satellite remote sensing [8]. This paper deals with the discussion of preliminary results of geomagnetic and GPR investigations, some of which have been verified by trial archaeological excavations which have unearthed some buried structures, improving the knowledge of the ceremonial areas of Tiwanaku. References [1] Lasaponara R., Leucci G., Masini N., Persico R., Scardozzi G., Towards an operative use of remote sensing for exploring the past using satellite data: The case study of Hierapolis (Turkey), Remote sensing of Environment, 174 (2016) : 148-164, doi:10.1016/j.rse.2015.12.016 [2] Masini N., Lasaponara R., Rizzo E., Orefici G. 2012. Integrated Remote Sensing Approach in Cahuachi (Peru): Studies and Results of the ITACA Mission (2007-2010), In: Lasaponara R., Masini N. (Eds) 2012, Satellite Remote Sensing: a new tool for Archaeology, Springer, Verlag Berlin Heidelberg, ISBN 978-90-481-8800-0, doi: 10.1007/978-90-481-8801-7_14; pp. 307-344 [3] Rizzo E., Masini N., Lasaponara R., Orefici G. 2010, ArchaeoGeophysical methods in the Templo del Escalonado (Cahuachi, Nasca, Perù), Near Surface Geophysics 8 (5), 433-439, doi:10.3997/1873-0604.2010030 [4] Masini N., Rizzo E., Lasaponara R., and Orefici G. 2008, Integrated remote sensing techniques for the detection of buried archaeological adobe structures: preliminary results in Cahuachi (Peru), Advances in Geosciences, 19, 75-82 [5] Lasaponara R., Leucci G., Masini N., Persico R. 2014. Investigating archaeological looting

Simulation Results of Double Forward Converter

Directory of Open Access Journals (Sweden)

P. Vijaya KUMAR

2009-12-01

Full Text Available This work aims to find a better forward converter for DC to DC conversion.Simulation of double forward converter in SMPS system is discussed in this paper. Aforward converter with RCD snubber to synchronous rectifier and/or to current doubleris also discussed. The evolution of the forward converter is first reviewed in a tutorialfashion. Performance parameters are discussed including operating principle, voltageconversion ratio, efficiency, device stress, small-signal dynamics, noise and EMI. Itscircuit operation and its performance characteristics of the forward converter with RCDsnubber and double forward converter are described and the simulation results arepresented.

Preliminary results on the cryogenic target for FIREX project

International Nuclear Information System (INIS)

Iwamoto, A.; Maekawa, R.; Mito, T.; Okamoto, M.; Motojima, O.; Nakai, M.; Norimatsu, T.; Nagai, K.

2006-01-01

Preliminary tests on the cryogenic target for the fast ignition realization experiment (FIREX) project has been conducted. A foam shell method is proposed to realize its target design. A foam target consists of three parts: a foam shell, a conical laser guide and a liquid or gas feeder made of glass. The shell is a hollow sphere (500 μm in diameter) with a uniform and thin foam layer (about 20 μm in thickness). Epoxy resin is utilized to assemble the parts into the target. Liquid fuel is fed into the shell by the feeder and is soaked up by the foam material through capillarity. The fuel is then solidified. Regarding target fabrication, one of the concerns is the influence on various thermal contractions from the different materials when it is cooled down to cryogenic environment. This paper describes the result on the validity check at cryogenic environment and the demonstration of H 2 liquefaction using a dummy target instead of the foam target. Judging from these results, the target assembled in the same process as the dummy target is sure to be practicable for the FIREX project. (authors)

WISE/NEOWISE OBSERVATIONS OF THE JOVIAN TROJANS: PRELIMINARY RESULTS

International Nuclear Information System (INIS)

Grav, T.; Mainzer, A. K.; Bauer, J.; Masiero, J.; Eisenhardt, P. R. M.; Blauvelt, E.; DeBaun, E.; Elsbury, D.; Gautier, T. IV; Gomillion, S.; Hand, E.; Wilkins, A.; Spahr, T.; McMillan, R. S.; Walker, R.; Cutri, R.; Wright, E.

2011-01-01

We present the preliminary analysis of over 1739 known and 349 candidate Jovian Trojans observed by the NEOWISE component of the Wide-field Infrared Survey Explorer (WISE). With this survey the available diameters, albedos, and beaming parameters for the Jovian Trojans have been increased by more than an order of magnitude compared to previous surveys. We find that the Jovian Trojan population is very homogenous for sizes larger than ∼10 km (close to the detection limit of WISE for these objects). The observed sample consists almost exclusively of low albedo objects, having a mean albedo value of 0.07 ± 0.03. The beaming parameter was also derived for a large fraction of the observed sample, and it is also very homogenous with an observed mean value of 0.88 ± 0.13. Preliminary debiasing of the survey shows that our observed sample is consistent with the leading cloud containing more objects than the trailing cloud. We estimate the fraction to be N(leading)/N(trailing) ∼ 1.4 ± 0.2, lower than the 1.6 ± 0.1 value derived by Szabó et al.

Computational fluid dynamics simulations and validations of results

CSIR Research Space (South Africa)

Sitek, MA

2013-09-01

Full Text Available Wind flow influence on a high-rise building is analyzed. The research covers full-scale tests, wind-tunnel experiments and numerical simulations. In the present paper computational model used in simulations is described and the results, which were...

Presenting simulation results in a nested loop plot.

Science.gov (United States)

Rücker, Gerta; Schwarzer, Guido

2014-12-12

Statisticians investigate new methods in simulations to evaluate their properties for future real data applications. Results are often presented in a number of figures, e.g., Trellis plots. We had conducted a simulation study on six statistical methods for estimating the treatment effect in binary outcome meta-analyses, where selection bias (e.g., publication bias) was suspected because of apparent funnel plot asymmetry. We varied five simulation parameters: true treatment effect, extent of selection, event proportion in control group, heterogeneity parameter, and number of studies in meta-analysis. In combination, this yielded a total number of 768 scenarios. To present all results using Trellis plots, 12 figures were needed. Choosing bias as criterion of interest, we present a 'nested loop plot', a diagram type that aims to have all simulation results in one plot. The idea was to bring all scenarios into a lexicographical order and arrange them consecutively on the horizontal axis of a plot, whereas the treatment effect estimate is presented on the vertical axis. The plot illustrates how parameters simultaneously influenced the estimate. It can be combined with a Trellis plot in a so-called hybrid plot. Nested loop plots may also be applied to other criteria such as the variance of estimation. The nested loop plot, similar to a time series graph, summarizes all information about the results of a simulation study with respect to a chosen criterion in one picture and provides a suitable alternative or an addition to Trellis plots.

Weldon Spring, Missouri, Raffinate Pits 1, 2, 3, and 4: Preliminary grout development screening studies for in situ waste immobilization

International Nuclear Information System (INIS)

McDaniel, E.W.; Gilliam, T.M.; Dole, L.R.; West, G.A.

1987-04-01

Results of Oak Ridge National Laboratory's initial support program to develop a preliminary grout formula to solidify in situ the Weldon Spring waste are presented. The screening study developed preliminary formulas based on a simulated composite waste and then tested the formulas on actual waste samples. Future data needs are also discussed. 1 ref., 6 figs., 9 tabs

Preliminary results on ocean dynamics from Skylab and their implications for future spacecraft

Science.gov (United States)

Hayes, J.; Pierson, W. J.; Cardone, V. J.

1975-01-01

The instrument aboard Skylab designated S193 - a combined passive and active microwave radar system acting as a radiometer, scatterometer, and altimeter - is used to measure the surface vector wind speeds in the planetary boundary layer over the oceans. Preliminary results corroborate the hypothesis that sea surface winds in the planetary boundary layer can be determined from satellite data. Future spacecraft plans for measuring a geoid with an accuracy up to 10 cm are discussed.

78 FR 32367 - Multilayered Wood Flooring From the People's Republic of China; Preliminary Results of...

Science.gov (United States)

2013-05-30

... From the People's Republic of China; Preliminary Results of Antidumping Duty New Shipper Review; 2011... duty order on multilayered wood flooring (``MLWF'') from the People's Republic of China (``PRC''). The period of review (``POR'') is May 26, 2011 through May 31, 2012. The review covers one exporter of...

Milestone M4900: Simulant Mixing Analytical Results

Energy Technology Data Exchange (ETDEWEB)

Kaplan, D.I.

2001-07-26

This report addresses Milestone M4900, ''Simulant Mixing Sample Analysis Results,'' and contains the data generated during the ''Mixing of Process Heels, Process Solutions, and Recycle Streams: Small-Scale Simulant'' task. The Task Technical and Quality Assurance Plan for this task is BNF-003-98-0079A. A report with a narrative description and discussion of the data will be issued separately.

Joint ARM/GCSS/SPARC TWP-ICE CRM Intercomparison Study: Description, Preliminary Results, and Invitation to Participate

Science.gov (United States)

Fridlind, A. M.; Ackerman, A. S.; Allen, G.; Beringer, J.; Comstock, J. M.; Field, P. R.; Gallagher, M.; Hacker, J. M.; Hume, T.; Jakob, C.; Liu, G.; Long, C. N.; Mather, J. H.; May, P. T.; McCoy, R. F.; McFarlane, S. A.; McFarquhar, G. M.; Minnis, P.; Petch, J. C.; Schumacher, C.; Turner, D. D.; Whiteway, J. A.; Williams, C. R.; Williams, P. I.; Xie, S.; Zhang, M.

2008-12-01

The 2006 Tropical Warm Pool - International Cloud Experiment (TWP-ICE) is 'the first field program in the tropics that attempted to describe the evolution of tropical convection, including the large-scale heat, moisture, and momentum budgets at 3-hourly time resolution, while at the same time obtaining detailed observations of cloud properties and the impact of the clouds on the environment' [May et al., 2008]. A cloud- resolving model (CRM) intercomparison based on TWP-ICE is now being undertaken by the Atmospheric Radiation Measurement (ARM), GEWEX Cloud Systems Study (GCSS), and Stratospheric Processes And their Role in Climate (SPARC) programs. We summarize the 16-day case study and the wealth of data being used to provide initial and boundary conditions, and evaluate some preliminary findings in the context of existing theories of moisture evolution in the tropical tropopause layer (TTL). Overall, simulated cloud fields evolve realistically by many measures. Budgets indicate that simulated convective flux convergence of water vapor is always positive or near zero at TTL elevations, except locally at lower levels during the driest suppressed monsoon conditions, while simulated water vapor deposition to hydrometeors always exceeds sublimation on average at all TTL elevations over 24-hour timescales. The next largest water vapor budget term is generally the nudging required to keep domain averages consistent with observations, which is at least partly attributable to large-scale forcing terms that cannot be derived from measurements. We discuss the primary uncertainties.

Utilisation of simulation in industrial design and resulting business opportunities (SISU) - MASIT18

Energy Technology Data Exchange (ETDEWEB)

Olin, M.; Leppaevuori, J.; Manninen, J. (VTT Technical Research Centre of Finland, Espoo (Finland)); Valli, A.; Hasari, H.; Koistinen, A.; Leppaenen, S. (Helsinki Polytechnic Stadia, City of Helsinki, Helsinki (Finland)); Lahti, S. (EVTEK University of Applied Sciences, Vantaa (Finland))

2008-07-01

In the SISU project, over 10 case studies are carried out in many different fields and applications. Results and experience of developing simulation applications have started to accumulate. One of the most important results this far is that there are many common features, both good and bad, between our test cases. Simulation is a fast, reliable, and often low risk method of studying different systems and processes. On the other hand, many applications need very expensive licences, plenty of parametric data and highly specialised knowledge in order to produce really valuable results. Industrial partners are acting like real customers in the case studies. We hope that this methodology will help us to answer our main question: how do we create a value chain from model development via model application for end users? The best thing to happen will be if partners learn to apply simulation productively. Other scientists and companies will follow, and new value chains will mushroom. In the case study of Mamec and EVTEK - Mixing model - the aim is to develop a fluid mechanical model for a mixing chamber. This study is similar to the preceding case of Watrec. In this study, the main problems have been in material properties area, because of non-Newtonian fluids and multiphase flows. Material property parameters of the non-Newtonian power law have been defined and flow field simulations have started. In the case study of Fortum and EVTEK - MDR - Measurement data reconciliation - the aim is to apply MDR in a power plant environment and study the possibility of developing a commercial additional tool for power plant simulation through the well-proven MDR technique based on linear filtering theory. The MDR method has been applied, for example, to energy and chemical processes. MDR is closely connected with system maintenance, simulation pre-processing and process diagnostics. Experimental work has proceeded from simple unit processes to large and complicated process systems. One

Fast Blood Vector Velocity Imaging: Simulations and Preliminary In Vivo Results

DEFF Research Database (Denmark)

Udesen, Jesper; Gran, Fredrik; Hansen, Kristoffer Lindskov

2007-01-01

for each pulse emission. 2) The transmitted pulse consists of a 13 bit Barker code which is transmitted simultaneously from each transducer element. 3) The 2-D vector velocity of the blood is found using 2-D speckle tracking between segments in consecutive speckle images. III Results: The method was tested...

Preliminary Results from Second Phase Sea Testing of the Wave Dragon Prototype Wave Energy Converter

DEFF Research Database (Denmark)

Soerensen, Hans Chr.; Tedd, James; Friis-Madsen, Erik

2006-01-01

In March 2006 the prototype Wave Dragon has been redeployed to a more energetic site in Nissum Bredning an inland sea in Western Denmark. This has followed a period of renovation of many aspects of the device which have resulted in 20% higher energy output. This paper describes the preliminary...

Preliminary results of an attempt to provide soil moisture datasets in order to verify numerical weather prediction models

International Nuclear Information System (INIS)

Cassardo, C.; Loglisci, N.

2005-01-01

In the recent years, there has been a significant growth in the recognition of the soil moisture importance in large-scale hydrology and climate modelling. Soil moisture is a lower boundary condition, which rules the partitioning of energy in terms of sensible and latent heat flux. Wrong estimations of soil moisture lead to wrong simulation of the surface layer evolution and hence precipitations and cloud cover forecasts could be consequently affected. This is true for large scale medium-range weather forecasts as well as for local-scale short range weather forecasts, particularly in those situations in which local convection is well developed. Unfortunately; despite the importance of this physical parameter there are only few soil moisture data sets sparse in time and in space around in the world. Due to this scarcity of soil moisture observations, we developed an alternative method to provide soil moisture datasets in order to verify numerical weather prediction models. In this paper are presented the preliminary results of an attempt to verify soil moisture fields predicted by a mesoscale model. The data for the comparison were provided by the simulations of the diagnostic land surface scheme LSPM (Land Surface Process Model), widely used at the Piedmont Regional Weather Service for agro-meteorological purposes. To this end, LSPM was initialized and driven by Synop observations, while the surface (vegetation and soil) parameter values were initialized by ECOCLIMAP global dataset at 1km 2 resolution

76 FR 26241 - Polyethylene Retail Carrier Bags From Thailand: Extension of Time Limit for Preliminary Results...

Science.gov (United States)

2011-05-06

... DEPARTMENT OF COMMERCE International Trade Administration [A-549-821] Polyethylene Retail Carrier Bags From Thailand: Extension of Time Limit for Preliminary Results of Antidumping Duty Administrative...) initiated an administrative review of the antidumping duty order on polyethylene retail carrier bags from...

DETECTION OF Helicobacter pylori IN GASTRIC MUCOSA OF SHEEP: PRELIMINARY RESULTS

Directory of Open Access Journals (Sweden)

A. Rella

2013-02-01

Full Text Available Helicobacter pylori is an organism widespread in humans and sometimes responsible for serious illnesses. It has been hypothesized the existence of animal reservoirs, and that the infection route by H. pylori involves multiple pathways including food-borne transmission as the microorganism has been detected from sheep, goat and cow milk. This work reports the preliminary results of a survey conducted in order to investigate the presence of H. pylori in gastric mucosa of sheep slaughtered in Apulia region (Italy employing a Nested Polymerase Chain Reaction (Nested-PCR assay for the detection of the phosphoglucosamine mutase gene (glmM, as screening method followed by conventional bacteriological isolation. Out of the 50 gastric mucosa samples examined, 3 (6% resulted positive for the presence of glmMgene, but at this time no strains were isolated. The results deserve further investigations to asses the role of ruminants as possible reservoirs of H. pylori.

Mass imbalances in EPANET water-quality simulations

Science.gov (United States)

Davis, Michael J.; Janke, Robert; Taxon, Thomas N.

2018-04-01

EPANET is widely employed to simulate water quality in water distribution systems. However, in general, the time-driven simulation approach used to determine concentrations of water-quality constituents provides accurate results only for short water-quality time steps. Overly long time steps can yield errors in concentration estimates and can result in situations in which constituent mass is not conserved. The use of a time step that is sufficiently short to avoid these problems may not always be feasible. The absence of EPANET errors or warnings does not ensure conservation of mass. This paper provides examples illustrating mass imbalances and explains how such imbalances can occur because of fundamental limitations in the water-quality routing algorithm used in EPANET. In general, these limitations cannot be overcome by the use of improved water-quality modeling practices. This paper also presents a preliminary event-driven approach that conserves mass with a water-quality time step that is as long as the hydraulic time step. Results obtained using the current approach converge, or tend to converge, toward those obtained using the preliminary event-driven approach as the water-quality time step decreases. Improving the water-quality routing algorithm used in EPANET could eliminate mass imbalances and related errors in estimated concentrations. The results presented in this paper should be of value to those who perform water-quality simulations using EPANET or use the results of such simulations, including utility managers and engineers.

Preliminary research results for parameter diagnostics of intense pulsed ion beams

International Nuclear Information System (INIS)

Yang Hailiang; Qiu Aici; Sun Jianfeng; He Xiaoping; Tang Junping; Wang Haiyang; Li Jingya; Ren Shuqing; Huang Jianjun; Zhang Jiasheng; Peng Jianchang; Ouyang Xiaoping; Zhang Guoguang; Li Hongyu

2004-01-01

The preliminary experimental results for parameter diagnostics of intense pulsed ion beams from the FLASH II accelerator were reported. The ion number of an intense pulsed ion beam were experimentally determined by monitoring delayed radioactivity from protons induced nuclear reactions in a 12 C target. The prompt γ-rays and diode Bremsstrahlung X-rays were measured with PIN semi-conductor detector and a ST401 plastic scintillator detector. The Bremsstrahlung distribution outside of the drift tube was detected with a thermoluminescent detector and the shielding design was also determined. The current densities of beam were measured with biased ion collector array. The ion beams were also recorded with a CR-39 detector. (author)

Preliminary results in double cusp tandem mirror MM-4U

International Nuclear Information System (INIS)

Ming Linzhou; Tian Zhongyu; Feng Xiaozhen

1990-10-01

MM-4U device and preliminary experimental results are presented. Main results are as follows: The plasma has been produced by means of the injection of strong electron current; the axial profile of the plasma potential and the plasma electron density have been obtained respectively, they had a simular form; the plasma potential in the centre of the east cusp, the west cusp and the simple mirror; V e = -180V, V w = -164V, V m -1.8V; the electron density: n e = 1.7 x 10 11 cm -3 , n w = 4.7 x 10 10 cm -3 , n m = 7.5 x 10 7 cm -3 ; the electron temperature: T e = (19.9 ± 1.6) eV, T w = (20.7 ± 1.7) eV; the plasma pressure at 8 cm on the right of the west cusp centre is about 6.76 Pa, β ≅ 1.7 x 10 -3 . The plasma instability has been observed in the simple mirror, its vibration frequency was 7∼9.2 kHz. The results are discussed. The next new task of the physical experiment are proposed

New large solar photocatalytic plant: set-up and preliminary results.

Science.gov (United States)

Malato, S; Blanco, J; Vidal, A; Fernández, P; Cáceres, J; Trincado, P; Oliveira, J C; Vincent, M

2002-04-01

A European industrial consortium called SOLARDETOX has been created as the result of an EC-DGXII BRITE-EURAM-III-financed project on solar photocatalytic detoxification of water. The project objective was to develop a simple, efficient and commercially competitive water-treatment technology, based on compound parabolic collectors (CPCs) solar collectors and TiO2 photocatalysis, to make possible easy design and installation. The design, set-up and preliminary results of the main project deliverable, the first European industrial solar detoxification treatment plant, is presented. This plant has been designed for the batch treatment of 2 m3 of water with a 100 m2 collector-aperture area and aqueous aerated suspensions of polycrystalline TiO2 irradiated by sunlight. Fully automatic control reduces operation and maintenance manpower. Plant behaviour has been compared (using dichloroacetic acid and cyanide at 50 mg l(-1) initial concentration as model compounds) with the small CPC pilot plants installed at the Plataforma Solar de Almería several years ago. The first results with high-content cyanide (1 g l(-1)) waste water are presented and plant treatment capacity is calculated.

The effect of parental involvement in CBT of anxious children: Preliminary results from a RCT study

DEFF Research Database (Denmark)

Esbjørn, Barbara Hoff; Breinholst, Sonja; Reinholdt-Dunne, Marie Louise

2011-01-01

Esbjørn, B. H., Breinholst, S., Reinholdt-Dunne, M. L., & Leth, I. (2011). The effect of parental involvement in CBT of anxious children: Preliminary results from a RCT study. Poster accepted for the Association for Behavioral and Cognitive Therapies, Toronto, Canada....

75 FR 25207 - Polyethylene Retail Carrier Bags From Malaysia: Extension of Time Limit for Preliminary Results...

Science.gov (United States)

2010-05-07

... polyethylene retail carrier bags from Malaysia for the period August 1, 2008, through July 31, 2009. See... DEPARTMENT OF COMMERCE International Trade Administration A-557-813 Polyethylene Retail Carrier Bags From Malaysia: Extension of Time Limit for Preliminary Results of Antidumping Duty Administrative...

Results of the Preliminary Test in the 1/4-Scale RCCS of the PMR200 VHTR

Energy Technology Data Exchange (ETDEWEB)

Kim, Jong-Hwan; Bae, Yoon-Yeong; Hong, Sung-Deok; Kim, Chan-Soo; Cho, Bong-Hyun; Kim, Min-Hwan [Nuclear Hydrogen Reactor Technology Development Dep., Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-10-15

The Reactor Cavity Cooling System (RCCS) is a key ex-vessel passive safety system that will ensure the safety of the PMR200, and its performance needs to be verified. For the difficulty of the full-scale test, a 1/4-scale RCCS facility, NACEF (Natural Cooling Experimental Facility), has been constructed at KAERI, and a shakedown test has been performed. A brief design and the preliminary test results of this facility are described. A 1/4-scale RCCS mockup of PMR200, NACEF, was constructed and tested preliminarily. The functioning of the facility worked quite well. Moreover, the preliminary test results show a fairly good agreement with past work except for the conductive heat transfer region in the riser bottom. After a remedy such as the installation of more precise flow meters and a more improved insulation, the test facility is likely to work well.

Criteria for safety-related nuclear plant operator actions: a preliminary assessment of available data

International Nuclear Information System (INIS)

Haas, P.M.; Bott, T.F.

1980-01-01

In the US, an effort has been underway for a number of years to develop a design standard to define when required manual operator action can be accepted as part of a nuclear plant design basis. Insufficient data are available to provide quantitative guidelines for the standard. To provide the necessary data base to support such standards and the necessary quantitative assessment of operator reliability, the US Nuclear Regulatory Commission is sponsoring a study at Oak National Laboratory to develop the data base. A preliminary assessment completed in April, 1979 concluded that sufficient data from US operating experience did not exist to provide an adequate data base. A program of research using full-scope nuclear plant simulators and results that are correlated to field data was suggested. That program was recently initiated. The approach, results and conclusions of the preliminary assessment are reviewed and the planned research program of simulator studies is summarised. (author)

Precise Hypocenter Determination around Palu Koro Fault: a Preliminary Results

Science.gov (United States)

Fawzy Ismullah, M. Muhammad; Nugraha, Andri Dian; Ramdhan, Mohamad; Wandono

2017-04-01

Sulawesi area is located in complex tectonic pattern. High seismicity activity in the middle of Sulawesi is related to Palu Koro fault (PKF). In this study, we determined precise hypocenter around PKF by applying double-difference method. We attempt to investigate of the seismicity rate, geometry of the fault and distribution of focus depth around PKF. We first re-pick P-and S-wave arrival time of the PKF events to determine the initial hypocenter location using Hypoellipse method through updated 1-D seismic velocity. Later on, we relocated the earthquake event using double-difference method. Our preliminary results show the distribution of relocated events are located around PKF and have smaller residual time than the initial location. We will enhance the hypocenter location through updating of arrival time by applying waveform cross correlation method as input for double-difference relocation.

Preliminary Results of the Louisiana Sex Offender Treatment Program

OpenAIRE

Lee A. Underwood; Frances L.L. Dailey; Carrie Merino; Yolanda Crump

2015-01-01

The purpose of this study was to offer preliminary support for the Louisiana Sex Offender Treatment Program (LSOTP) in addressing the needs of juvenile sex offenders. Research objectives were (1) to offer statistical evidence for reductions in anxiety, depression, cognitive distortion and negative attitudes towards women comparing a group of 21 adolescents, 12 of whom received services as usual and nine of whom participated in the LSOTP. A controlled experimental evaluation design was utilize...

Experimental-demonstrative system for energy conversion using hydrogen fuel cell - preliminary results

International Nuclear Information System (INIS)

Stoenescu, D.; Stefanescu, I.; Patularu, I.; Culcer, M.; Lazar, R.E.; Carcadea, E.; Mirica, D. . E-mail address of corresponding author: daniela@icsi.ro; Stoenescu, D.)

2005-01-01

It is well known that hydrogen is the most promising solution of future energy, both for long and medium term strategies. Hydrogen can be produced using many primary sources (natural gas, methane, biomass, etc.), it can be burned or chemically react having a high yield of energy conversion, being a non-polluted fuel. This paper presents the preliminary results obtained by ICSI Rm. Valcea in an experimental-demonstrative conversion energy system made by a sequence of hydrogen purification units and a CO removing reactors until a CO level lower than 10ppm, that finally feeds a hydrogen fuel stack. (author)

Head teacher professional networks in Italy: preliminary results of a national survey

Directory of Open Access Journals (Sweden)

Maurissens Isabel de

2016-06-01

Full Text Available In this article, we present the preliminary results of a national survey conducted by INDIRE on head teachers communities and professional networks. About one-fourth of the total population of Italian public school leaders participated in the survey. One of the main intents of this research is to contribute to understanding of the phenomenon of professional networks frequented by school leaders and to pave the way for a further reflection on how to use such networks for head teachers’ training so as to support their daily professional practice conducted too often in isolation.

Design and preliminary results of a fuel flexible industrial gas turbine combustor

Science.gov (United States)

Novick, A. S.; Troth, D. L.; Yacobucci, H. G.

1981-01-01

The design characteristics are presented of a fuel tolerant variable geometry staged air combustor using regenerative/convective cooling. The rich/quench/lean variable geometry combustor is designed to achieve low NO(x) emission from fuels containing fuel bound nitrogen. The physical size of the combustor was calculated for a can-annular combustion system with associated operating conditions for the Allison 570-K engine. Preliminary test results indicate that the concept has the potential to meet emission requirements at maximum continuous power operation. However, airflow sealing and improved fuel/air mixing are necessary to meet Department of Energy program goals.

78 FR 2363 - Certain Cased Pencils From the People's Republic of China: Preliminary Results of Antidumping...

Science.gov (United States)

2013-01-11

... the People's Republic of China: Preliminary Results of Antidumping Duty Administrative Review and... Republic of China (``PRC''). The period of review (``POR'') is December 1, 2010, through November 30, 2011. The review covers one exporter of subject merchandise, Beijing Fila Dixon Stationery Company, Ltd. a...

78 FR 1834 - Magnesium Metal From the People's Republic of China: Preliminary Results of Antidumping Duty...

Science.gov (United States)

2013-01-09

... People's Republic of China: Preliminary Results of Antidumping Duty Administrative Review; 2011-2012... on magnesium metal from the People's Republic of China (``PRC''). The period of review (``POR'') is April 1, 2011, through March 31, 2012. This review covers one PRC company, Tianjin Magnesium...

Fracture toughness of irradiated candidate materials for ITER first wall/blanket structures: Preliminary results

International Nuclear Information System (INIS)

Alexander, D.J.; Pawel, J.E.; Grossbeck, M.L.; Rowcliffe, A.F.

1993-01-01

Candidate materials for first wall/blanket structures in ITER have been irradiated to damage levels of about 3 dpa at temperatures of either 60 or 250 degrees C. Preliminary results have been obtained for several of these materials irradiated at 60 degrees C. The results show that irradiation at this temperature reduces the fracture toughness of austenitic stainless steels, but the toughness remains quite high. The unloading compliance technique developed for the subsize disk compact specimens works quite well, particularly for materials with lower toughness. Specimens of materials with very high toughness deform excessively, and this results in experimental difficulties

A systematic study of biochemical effects of heavy metal pollution. Programme of the research and preliminary results on cadmium and lead

International Nuclear Information System (INIS)

Sabbioni, E.; Girardi, F.; Marafante, E.

1975-01-01

The distribution of labelled metal pollutants at low-dose in organs, subcellular fractions and isolated and fractional component of subcellular fractions, in view of identifying specific metal binding component, was studied. Two types of experiments were carried out, on rats. Long-term experiments (up to 3-4 months), the labelled metal was administred at low concentrations (environmental levels) over long periods of time in order to simulate as close as possible the conditions of polluted environments. Short-term experiments (1-7 days), the labelled metal was injected at acute or subacute levels. 5 elements were selected (Cd, Zn, Se, Hg, Cr) for the long term experiments and 4 elements (Pb, V, Ni, Be) for the short term experiments. The essential present knowledge on the behavior at cellular level of heavy metals which were chosen were summarized. Preliminary results on biochemical effects of cadmium and lead were reported

Sealing a nuclear waste repository in Columbia river basalt: preliminary results

International Nuclear Information System (INIS)

Hodges, F.N.

1980-01-01

The long containment time required of repositories for nuclear waste (10 4 to 10 6 years) requires that materials used for repository seals be stable in the geologic environment of the repository and of proven longevity. A list of candidate materials for sealing a repository in Columbia River Basalts has been prepared and refined through laboratory testing. The most feasible techniques for emplacing preferred plug materials have been identified and the resultant plugs have been evaluated on the basis of design functions. Preconceptual designs for tunnel, shaft, and borehole seals consist of multiple zone plugs with each zone fulfilling one or more design functions. Zones of disturbed rock around tunnels and shafts, resulting from excavation and subsequent stress release, are zones of higher permeability and of possible fluid migration. In preliminary designs the disturbed zones are blocked by cut-off collars filled with low permeability materials

Preliminary results on a 4 kJ, 140 k A plasma focus

International Nuclear Information System (INIS)

Silva, Patricio; Favre, Mario; Chuaqui, Hernan; Wyndham, Edmund

1996-01-01

Preliminary results on the operation of a 4 kJ, 140 kA Plasma Focus device are presented. The machine operates Hydrogen and Hydrogen-Argon mixtures at pressures between 400 m Torr to 10 Torr. Main diagnostics include electric and current measurements, time and space resolved X-ray observations, with limited spectral resolution, and B-dot sensors to monitor the evolution of de current sheet during the run up phase of the discharge. The results indicate that good focus is obtained in the above pressure range. This is inferred from I-dot traces and Pin diode and pin-hole camera X-ray observations. The B-dot loops suggest that a symmetric current sheet is produced. These results show that the machine exhibits a reliable performance, which allows further studies on dense transient plasmas to be developed. (author)

Introducing handheld computing into a residency program: preliminary results from qualitative and quantitative inquiry.

OpenAIRE

Manning, B.; Gadd, C. S.

2001-01-01

Although published reports describe specific handheld computer applications in medical training, we know very little yet about how, and how well, handheld computing fits into the spectrum of information resources available for patient care and physician training. This paper reports preliminary quantitative and qualitative results from an evaluation study designed to track changes in computer usage patterns and computer-related attitudes before and after introduction of handheld computing. Pre...

Using relational databases to collect and store discrete-event simulation results

DEFF Research Database (Denmark)

Poderys, Justas; Soler, José

2016-01-01

, export the results to a data carrier file and then process the results stored in a file using the data processing software. In this work, we propose to save the simulation results directly from a simulation tool to a computer database. We implemented a link between the discrete-even simulation tool...... and the database and performed performance evaluation of 3 different open-source database systems. We show, that with a right choice of a database system, simulation results can be collected and exported up to 2.67 times faster, and use 1.78 times less disk space when compared to using simulation software built...

Titan's organic chemistry: Results of simulation experiments

Science.gov (United States)

Sagan, Carl; Thompson, W. Reid; Khare, Bishun N.

1992-01-01

Recent low pressure continuous low plasma discharge simulations of the auroral electron driven organic chemistry in Titan's mesosphere are reviewed. These simulations yielded results in good accord with Voyager observations of gas phase organic species. Optical constants of the brownish solid tholins produced in similar experiments are in good accord with Voyager observations of the Titan haze. Titan tholins are rich in prebiotic organic constituents; the Huygens entry probe may shed light on some of the processes that led to the origin of life on Earth.

77 FR 73422 - Seamless Refined Copper Pipe and Tube From Mexico: Preliminary Results of Antidumping Duty...

Science.gov (United States)

2012-12-10

... Refined Copper Pipe and Tube From Mexico and the People's Republic of China: Antidumping Duty Orders and... and Tube From Mexico: Preliminary Results of Antidumping Duty Administrative Review; 2010-2011 AGENCY... on seamless refined copper pipe and tube from Mexico. The review covers two producers/ exporters of...

78 FR 6069 - Laminated Woven Sacks From the People's Republic of China: Preliminary Results of Antidumping...

Science.gov (United States)

2013-01-29

... the People's Republic of China: Preliminary Results of Antidumping Duty Administrative Review; 2011... antidumping duty order on laminated woven sacks (``sacks'') from the People's Republic of China (``PRC''). The period of review (``POR'') is August 1, 2011, through July 31, 2012. The review covers one exporter of...

Simulation and performance of brushless DC motor actuators

OpenAIRE

Gerba, Alex

1985-01-01

The simulation model for a Brushless D.C. Motor and the associated commutation power conditioner transistor model are presented. The necessary conditions for maximum power output while operating at steady-state speed and sinusoidally distributed air-gap flux are developed. Comparisons of simulated model with the measured performance of a typical motor are done both on time response waveforms and on average performance characteristics. These preliminary results indicate good ...

Uranium and thorium recovery in thorianite ore-preliminary results

Energy Technology Data Exchange (ETDEWEB)

Gaiotte, Joao V.M. [Universidade Federal de Alfenas, Pocos de Caldas, MG (Brazil); Villegas, Raul A.S.; Fukuma, Henrique T., E-mail: rvillegas@cnen.gov.br, E-mail: htfukuma@cnen.gov.br [Comissao Nacional de Energia Nuclear (CNEN), Pocos de Caldas, MG (Brazil). Lab. de Pocos de Caldas

2011-07-01

This work presents the preliminary results of the studies aiming to develop a hydrometallurgical process to produce uranium and thorium concentrates from thorianite ore from Amapa State, Brazil. This process comprises two major parts: acid leaching and Th/U recovery using solvent extraction strategies. Thorianite ore has a typical composition of 60 - 70% of thorium, 8 - 10% lead and 7 - 10% uranium. Sulfuric acid leaching operational conditions were defined as follows: acid/ore ratio 7.5 t/t, ore size below 65 mesh (Tyler), 2 hours leaching time and temperature of 100 deg C. Leaching tests results showed that uranium and thorium recovery exceeded 95%, whereas 97% of lead ore content remained in the solid form. Uranium and thorium simultaneous solvent extraction is necessary due to high sulfate concentration in the liquor obtained from leaching, so the Primene JM-T primary anime was used for this extraction step. Aqueous raffinate from extraction containing sulfuric acid was recycled to the leaching step, reducing acid uptake around 60%, to achieve a net sulfuric acid consumption of 3 t/t of ore. Uranium and thorium simultaneous stripping was performed using sodium carbonate solution. In the aqueous stripped it was added sulfuric acid at pH 1.5, followed by a second solvent extraction step using the tertiary amine Alamine 336. The following stripping step was done with a solution of sodium chloride, resulting in a final solution of 23 g L-1 uranium. (author)

Preliminary results from the Chicago air shower array and the Michigan muon array

International Nuclear Information System (INIS)

Krimm, H.A.; Cronin, J.W.; Fick, B.E.; Gibbs, K.G.; Mascarenhas, N.C.; McKay, T.A.; Mueller, D.; Newport, B.J.; Ong, R.A.; Rosenberg, L.J.; Wiedenbeck, M.E.; Green, K.D.; Matthews, J.; Nitz, D.; Sinclair, D.; van der Velde, J.C.

1991-01-01

The Chicago Air Shower Array (CASA) is a large area surface array designed to detect extensive air showers (EAS) produced by primaries with energy ∼100 TeV. It operates in coincidence with the underground Michigan Muon Array (MIA). Preliminary results are presented from a search for steady emission and daily emission from three astrophysical sources: Cygnus X-3, Hercules X-1, and the Crab nebula and pulsar. There is no evidence for a significant signal from any of these sources in the 1989 data

Thermoluminescent dosemeters characterization for patient dosimetry in diagnostic radiology preliminary results

International Nuclear Information System (INIS)

Castro, William J.; Squair, Peterson L.; Gonzaga, Natalia B.; Nogueira, Maria S.; Silva, Teogenes A. da

2009-01-01

The determination of the metrological characteristics of thermoluminescent (TL) dosimeters plays an important role in dosimetry of patients submitted to x-ray examinations for diagnostic purpose. Entrance surface doses can be measured with TL dosimeters to verify the compliance with the diagnostic reference levels. Organ doses can be estimated through TL measurements in an anthropomorphic phantom which it allows the radiation risk assessment. In this work, LiF:Mg,Ti (TLD-100) rod and chip thermoluminescent dosimeters were characterized considering their use for patient dosimetry in computerized tomography and mammography. Preliminary results showed that TL dosimeters have a response reproducibility of 7.8% and 4.8% and homogeneity of 18.4% and 6.5% for rod and chip shapes, respectively. (author)

Preliminary results on epidemiology of Coconut Lethal Yellowing in Ghana

Directory of Open Access Journals (Sweden)

Bonnot François

2009-03-01

Full Text Available Epidemiological studies are of major importance in understanding the determinants of plant diseases in order to control the risks of their spreading. A research programme on the epidemiology of coconut lethal yellowing, or Cape Saint Paul Wilt Disease (CSPWD, in Ghana was launched in March 2007. The objective was to characterize the distribution and spread of the disease in space and time at various scales, and their relation with the environment. This article presents the general strategy used to evaluate the incidence of CSPWD along with the environmental, ecological and agronomical variables at regional level. A survey was undertaken on 1,166 plots of Coconut Sector Development Project (CSDP planted with Malayan Yellow Dwarf (MYD × Vanuatu Tall (VTT hybrids in Western Region and Central Region. Preliminary results on the distribution of CSPWD and outside variables at regional scale, along with their relations, are given.

78 FR 13321 - Silicon Metal From the People's Republic of China: Preliminary Results of Antidumping Duty...

Science.gov (United States)

2013-02-27

... People's Republic of China: Preliminary Results of Antidumping Duty Administrative Review; 2011-2012... administrative review of the antidumping duty order on silicon metal from the People's Republic of China (``PRC'') for the period of review (``POR'') June 1, 2011, through May 31, 2012. This review covers one PRC...

Tellurium in active volcanic environments: Preliminary results

Science.gov (United States)

Milazzo, Silvia; Calabrese, Sergio; D'Alessandro, Walter; Brusca, Lorenzo; Bellomo, Sergio; Parello, Francesco

2014-05-01

Tellurium is a toxic metalloid and, according to the Goldschmidt classification, a chalcophile element. In the last years its commercial importance has considerably increased because of its wide use in solar cells, thermoelectric and electronic devices of the last generation. Despite such large use, scientific knowledge about volcanogenic tellurium is very poor. Few previous authors report result of tellurium concentrations in volcanic plume, among with other trace metals. They recognize this element as volatile, concluding that volcanic gases and sulfur deposits are usually enriched with tellurium. Here, we present some results on tellurium concentrations in volcanic emissions (plume, fumaroles, ash leachates) and in environmental matrices (soils and plants) affected by volcanic emissions and/or deposition. Samples were collected at Etna and Vulcano (Italy), Turrialba (Costa Rica), Miyakejima, Aso, Asama (Japan), Mutnovsky (Kamchatka) at the crater rims by using common filtration techniques for aerosols (polytetrafluoroethylene filters). Filters were both eluted with Millipore water and acid microwave digested, and analyzed by inductively coupled plasma mass spectrometry (ICP-MS). Volcanic ashes emitted during explosive events on Etna and Copahue (Argentina) were analyzed for tellurium bulk composition and after leaching experiments to evaluate the soluble fraction of tellurium. Soils and leaves of vegetation were also sampled close to active volcanic vents (Etna, Vulcano, Nisyros, Nyiragongo, Turrialba, Gorely and Masaya) and investigated for tellurium contents. Preliminary results showed very high enrichments of tellurium in volcanic emissions comparing with other volatile elements like mercury, arsenic, thallium and bismuth. This suggests a primary transport in the volatile phase, probably in gaseous form (as also suggested by recent studies) and/or as soluble salts (halides and/or sulfates) adsorbed on the surface of particulate particles and ashes. First

Preliminary I&C Design for LORELEI

International Nuclear Information System (INIS)

Korotkin, S.; Kaufman, Y.; Guttmann, E. B.; Levy, S.; Amidan, D.; Gdalyho, B.; Cahana, T.; Ellenbogen, A.; Arad, M.; Weiss, Y.; Sasson, A.; Ferry, L.; Bourrelly, F.; Cohen, Y.

2014-01-01

This document summarizes the preliminary I&C design for LORELEI experiment The preliminary design deals with considerations regarding appropriate safety and service instrumentation. The determined closed loop control rules for temperature and position will be implemented in the detailed design. The Computer Aided Operator Decisions System (CAODS) will be used for prediction of hot spot temperature and thickness of oxidation layer using Baker-Just correlation. The proposed hybrid simulation system comprising of both virtual and real hardware will be in-cooperated for LORELEI verification. It will perform both integration cold tests for a partial hardware loop and virtual tests for the final I&C design

2012 Annual Report: Simulate and Evaluate the Cesium Transport and Accumulation in Fukushima-Area Rivers by the TODAM Code

Energy Technology Data Exchange (ETDEWEB)

Onishi, Yasuo; Yokuda, Satoru T.

2013-03-28

Pacific Northwest National Laboratory initiated the application of the time-varying, one-dimensional sediment-contaminant transport code, TODAM (Time-dependent, One-dimensional, Degradation, And Migration) to simulate the cesium migration and accumulation in the Ukedo River in Fukushima. This report describes the preliminary TODAM simulation results of the Ukedo River model from the location below the Ougaki Dam to the river mouth at the Pacific Ocean. The major findings of the 100-hour TODAM simulation of the preliminary Ukedo River modeling are summarized as follows:

Preliminary Results of Autotuning GEMM Kernels for the NVIDIA Kepler Architecture- GeForce GTX 680

Energy Technology Data Exchange (ETDEWEB)

Kurzak, Jakub [Univ. of Tennessee, Knoxville, TN (United States); Luszczek, Pitor [Univ. of Tennessee, Knoxville, TN (United States); Tomov, Stanimire [Univ. of Tennessee, Knoxville, TN (United States); Dongarra, Jack [Univ. of Tennessee, Knoxville, TN (United States); Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Univ. of Manchester (United Kingdom)

2012-04-01

Kepler is the newest GPU architecture from NVIDIA, and the GTX 680 is the first commercially available graphics card based on that architecture. Matrix multiplication is a canonical computational kernel, and often the main target of initial optimization efforts for a new chip. This article presents preliminary results of automatically tuning matrix multiplication kernels for the Kepler architecture using the GTX 680 card.

The Titan Haze Simulation Experiment: Latest Laboratory Results and Dedicated Plasma Chemistry Model

Science.gov (United States)

Sciamma-O'Brien, Ella; Raymond, Alexander; Mazur, Eric; Salama, Farid

2018-06-01

Here, we present the latest results on the gas and solid phase analyses in the Titan Haze Simulation (THS) experiment. The THS experiment, developed at NASA Ames’ COSmIC facility is a unique experimental platform that allows us to simulate Titan’s complex atmospheric chemistry at Titan-like temperature (200 K) by cooling down N2-CH4-based mixtures in a supersonic expansion before inducing the chemistry by plasma.Gas phase: The residence time of the jet-accelerated gas in the active plasma region is less than 4 µs, which results in a truncated chemistry enabling us to control how far in the chain of reactions the chemistry is processing. By adding heavier molecules in the initial gas mixture, it is then possible to study the first and intermediate steps of Titan’s atmospheric chemistry as well as specific chemical pathways, as demonstrated by mass spectrometry and comparison to Cassini CAPS data [1]. A new model was recently developed to simulate the plasma chemistry in the THS. Calculated mass spectra produced by this model are in good agreement with the experimental THS mass spectra, confirming that the short residence time in the plasma cavity limits the growth of larger species [2].Solid phase: Scanning electron microscopy and infrared spectroscopy have been used to investigate the effect of the initial gas mixture on the morphology of the THS Titan aerosol analogs as well as on the level and nature of the nitrogen incorporation into these aerosols. A comparison to Cassini VIMS observational data has shown that the THS aerosols produced in simpler mixtures, i.e., that contain more nitrogen and where the N-incorporation is in isocyanide-type molecules instead of nitriles, are more representative of Titan’s aerosols [3]. In addition, a new optical constant facility has been developed at NASA Ames that allows us to determine the complex refractive indices of THS Titan aerosol analogs from NIR to FIR (0.76-222 cm-1). The facility and preliminary results

Development of a distress inventory for cancer: preliminary results.

Directory of Open Access Journals (Sweden)

Thomas B

2002-01-01

Full Text Available CONTEXT: Advances in cancer treatment have led to cure and prolongation of patients′ lives; however associated psychosocial problems, including distress, can detrimentally affect patients′ compliance with treatment and ultimately, their outcome. Symptom distress has been well addressed in many studies; however, psychological distress has only been quantified by using depression or anxiety scales/checklists or quality of life scales containing a distress sub scale/component or by the use of scales that are not psychological distress-specific. AIMS: The present study is an attempt to construct a psychological distress inventory for specific use with cancer patients. SETTINGS AND DESIGN: The standardisation sample consisted of 63 randomly selected patients with head and neck cancer who had undergone/ were undergoing curative treatment at the Regional Cancer Centre, Trivandrum. PATIENTS AND METHODS: The Distress Inventory for Cancer contained 57 positively and negatively toned items. An item analysis was conducted, followed by a factor analysis, thereby identifying the domains influencing distress. RESULTS: The final questionnaire contained 26 items subdivided into four domains viz. the personal, spiritual, physical, and the family domains, with each domain providing a sub score. The reliability coefficient (Cronbach′s alpha of the scale was found to be 0.85. CONCLUSIONS: These are the preliminary results of an ongoing study on global distress and tool development process. Reported here is the first step towards development of such tool.

Stokes polarimetry probe for skin lesion evaluation: preliminary results

Science.gov (United States)

Louie, Daniel C.; Tchvialeva, Lioudmilla; Kalia, Sunil; Lui, Harvey; Lee, Tim K.

2018-02-01

This paper reports on the design of a prototype in-vivo Stokes polarimetry probe for skin lesion evaluation, and preliminary results from skin phantom and clinical trials of this device. The probe releases a single millisecond-long pulse from a laser diode with either linear or circular polarization. It then captures the resulting backscattered far-field polarization speckle and calculates the Stokes parameters. This probe was designed with three novel innovations in mind. First, the Stokes vector is captured quickly, using low-cost components without the use of moving parts. Second, a compact collimated laser diode was used as the light source. Third, the device and detector geometry were designed to produce and capture a uniform speckle field. In the first clinical trial of this device, measurements were taken from a variety of skin lesions, both cancerous and benign. The Stokes vector was measured and used to calculate the degree of polarization (DOP), the azimuth angle, and the ellipticity angle of the polarization ellipse for two input light polarizations. Among other findings, the DOP for circular polarized input light was consistently lower than the DOP for linear polarized input light. These findings indicate the potential for a fast and low-cost in-vivo skin cancer screening tool, and encourages the continuing development of this probe's techniques.

Preliminary results from the U.S. participation in the 2000 Beam Park Experiment

Science.gov (United States)

Stansbery, Gene

2001-10-01

The United States participated in the 2000 Beam Park Experiment (BPE) conducted in late October, 2000 under the auspices of the Inter-Agency Space Debris Coordination Committee (IADC). The U.S. participated using several sensors which have participated in previous campaigns: Haystack, TRADEX, and COBRA DANE radars, and the Liquid Mirror Telescope. New to the BPE experiments this time are the GBR-P radar located at Kwajalein Atoll and the Haystack Auxiliary (HAX) radar located in Massachusetts. This paper will present and discuss preliminary results from each of the participating U.S. sensors.

Preliminary Results on the Experimental Investigation of the Structure Functions of Bound Nucleons

Energy Technology Data Exchange (ETDEWEB)

Bodek, Arie [Univ. of Rochester, NY (United States); Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States)

2016-08-01

We present preliminary results on an experimental study of the nuclear modification of the longitudinal ($\\sigma_L$) and transverse ($\\sigma_T$) structure functions of nucleons bound in nuclear targets. The origin of these modifications (commonly referred as as the EMC effect) is not fully understood. Our measurements of R= $\\sigma_L / \\sigma_T$ for nuclei ($R_A$) and for deuterium ($R_D$) indicate that nuclear modifications of the structure functions of bound nucleons are different for the longitudinal and transverse structure functions, and that contrary to expectation from several theoretical models, $R_A< R_D$.

Preliminary results from a novel CVD diamond detector system for molecular imaging applications

International Nuclear Information System (INIS)

Mahon, A.R.

1996-01-01

A novel biomolecular imaging system incorporating a Chemical Vapour Deposition diamond detector is in development. The synthetic diamond is used as a UV detector to image nucleic acids in electrophoresis gels. The microstrip diamond detector currently has a spatial resolution of 30 μm. Preliminary results are presented which include: QE measurements of diamond detectors, detector time response, detector UV response and current detection limits of biomolecules in gel. The potential applications of the technology, and its significant advantages in speed and sensitivity over the current systems are discussed

Medical Simulation Practices 2010 Survey Results

Science.gov (United States)

McCrindle, Jeffrey J.

2011-01-01

Medical Simulation Centers are an essential component of our learning infrastructure to prepare doctors and nurses for their careers. Unlike the military and aerospace simulation industry, very little has been published regarding the best practices currently in use within medical simulation centers. This survey attempts to provide insight into the current simulation practices at medical schools, hospitals, university nursing programs and community college nursing programs. Students within the MBA program at Saint Joseph's University conducted a survey of medical simulation practices during the summer 2010 semester. A total of 115 institutions responded to the survey. The survey resus discuss overall effectiveness of current simulation centers as well as the tools and techniques used to conduct the simulation activity

Electron-cloud simulation results for the PSR and SNS

International Nuclear Information System (INIS)

Pivi, M.; Furman, M.A.

2002-01-01

We present recent simulation results for the main features of the electron cloud in the storage ring of the Spallation Neutron Source (SNS) at Oak Ridge, and updated results for the Proton Storage Ring (PSR) at Los Alamos. In particular, a complete refined model for the secondary emission process including the so called true secondary, rediffused and backscattered electrons has been included in the simulation code

ROUND-ROBIN ATOM-PROBE EXPERIMENT : PRELIMINARY RESULTS IN JAPAN

OpenAIRE

Nakamura , S.

1986-01-01

A round-robin experiment were to be carried out by 6 laboratories in Japan (Nishikawa ; Tokyo Inst. Tech., Sakurai and Igata ; Univ. of Tokyo, Ishikawa ; Hitachi, Tanino ; Nippon Steel Corp. and Nakamura ; Osaka Univ.) under the normal operating condition (T < l00 °K,. pulse fraction ~ 15% ~, P < 10-9 torr). Fe-Cr-Al and W-25%Re alloys, which are divided from a single wire were chosen as the specimen materials. A preliminary analysis of the W-Re alloy of the laboratory concerned show the good...

Towards a non-wired simulator for reliability analysis

International Nuclear Information System (INIS)

Jurvillier, I.; Laviron, A.; Blin, A.

1991-11-01

This paper outlines the objectives and preliminary results of a research programme aiming to increase the advantages of electronic simulators used for reliability studies of complex systems. Research work has resulted in the design of a device based on an electronic simulator capable of carrying out all types of simulation without the drawback of wiring, as is currently the case. Its performance levels as regards speed are comparable to those of wired simulators and this is its main advantage over studies made on a computer. In addition, the simulator is connected to a computer which greatly increases system flexibility and user-friendliness. The first results obtained illustrate what characteristics can be expected of such a system, both as regards the anticipated computation time and the extended processing capabilities (such as the study of common cause failures). (author) [fr

Towards a non-wired simulator for reliability analysis

International Nuclear Information System (INIS)

Blin, A.; Laviron, A.; Jurvillier, I.

1991-08-01

This paper outlines the objectives and preliminary results of a research programme aiming to increase the advantages of electronic simulators used for reliability studies of complex systems. Research work has resulted in the design of a device based on an electronic simulator capable of carrying out all types of simulation without the drawback of wiring, as is currently the case. Its performance levels as regards speed are comparable to those of wired simulators and this is its main advantage over studies made on a computer. In addition, the simulator is connected to a computer which greatly increases system flexibility and user-friendliness. The first results obtained illustrate what characteristics can be expected of such a system, both as regards the anticipated computation time and the extended processing capabilities (such as the study of common cause failures)

Development of a helicon ion source: Simulations and preliminary experiments

Science.gov (United States)

Afsharmanesh, M.; Habibi, M.

2018-03-01

In the present context, the extraction system of a helicon ion source has been simulated and constructed. Results of the ion source commissioning at up to 20 kV are presented as well as simulations of an ion beam extraction system. Argon current of more than 200 μA at up to 20 kV is extracted and is characterized with a Faraday cup and beam profile monitoring grid. By changing different ion source parameters such as RF power, extraction voltage, and working pressure, an ion beam with current distribution exhibiting a central core has been detected. Jump transition of ion beam current emerges at the RF power near to 700 W, which reveals that the helicon mode excitation has reached this power. Furthermore, measuring the emission line intensity of Ar ii at 434.8 nm is the other way we have used for demonstrating the mode transition from inductively coupled plasma to helicon. Due to asymmetrical longitudinal power absorption of a half-helix helicon antenna, it is used for the ion source development. The modeling of the plasma part of the ion source has been carried out using a code, HELIC. Simulations are carried out by taking into account a Gaussian radial plasma density profile and for plasma densities in range of 1018-1019 m-3. Power absorption spectrum and the excited helicon mode number are obtained. Longitudinal RF power absorption for two different antenna positions is compared. Our results indicate that positioning the antenna near to the plasma electrode is desirable for the ion beam extraction. The simulation of the extraction system was performed with the ion optical code IBSimu, making it the first helicon ion source extraction designed with the code. Ion beam emittance and Twiss parameters of the ellipse emittance are calculated at different iterations and mesh sizes, and the best values of the mesh size and iteration number have been obtained for the calculations. The simulated ion beam extraction system has been evaluated using optimized parameters such

Comparison the Results of Numerical Simulation And Experimental Results for Amirkabir Plasma Focus Facility

Science.gov (United States)

Goudarzi, Shervin; Amrollahi, R.; Niknam Sharak, M.

2014-06-01

In this paper the results of the numerical simulation for Amirkabir Mather-type Plasma Focus Facility (16 kV, 36μF and 115 nH) in several experiments with Argon as working gas at different working conditions (different discharge voltages and gas pressures) have been presented and compared with the experimental results. Two different models have been used for simulation: five-phase model of Lee and lumped parameter model of Gonzalez. It is seen that the results (optimum pressures and current signals) of the Lee model at different working conditions show better agreement than lumped parameter model with experimental values.

Comparison the results of numerical simulation and experimental results for Amirkabir plasma focus facility

International Nuclear Information System (INIS)

Goudarzi, Shervin; Amrollahi, R; Sharak, M Niknam

2014-01-01

In this paper the results of the numerical simulation for Amirkabir Mather-type Plasma Focus Facility (16 kV, 36μF and 115 nH) in several experiments with Argon as working gas at different working conditions (different discharge voltages and gas pressures) have been presented and compared with the experimental results. Two different models have been used for simulation: five-phase model of Lee and lumped parameter model of Gonzalez. It is seen that the results (optimum pressures and current signals) of the Lee model at different working conditions show better agreement than lumped parameter model with experimental values.

Design Techniques and Reservoir Simulation

Directory of Open Access Journals (Sweden)

Ahad Fereidooni

2012-11-01

Full Text Available Enhanced oil recovery using nitrogen injection is a commonly applied method for pressure maintenance in conventional reservoirs. Numerical simulations can be practiced for the prediction of a reservoir performance in the course of injection process; however, a detailed simulation might take up enormous computer processing time. In such cases, a simple statistical model may be a good approach to the preliminary prediction of the process without any application of numerical simulation. In the current work, seven rock/fluid reservoir properties are considered as screening parameters and those parameters having the most considerable effect on the process are determined using the combination of experimental design techniques and reservoir simulations. Therefore, the statistical significance of the main effects and interactions of screening parameters are analyzed utilizing statistical inference approaches. Finally, the influential parameters are employed to create a simple statistical model which allows the preliminary prediction of nitrogen injection in terms of a recovery factor without resorting to numerical simulations.

Preliminary prediction of inflow into the D-holes at the Stripa Mine

International Nuclear Information System (INIS)

Long, J.C.S.; Karasaki, K.; Davey, A.; Peterson, J.; Landsfeld, M.; Kemeny, J.; Martel, S.

1990-02-01

Lawrence Berkeley Laboratory (LBL) is contracted by the US Department of Energy to provide an auxiliary modeling effort for the Stripa Project. Within this effort, we are making calculations of inflow to the Simulated Drift Experiment (SDE), i.e. inflow to six parallel, closely spaced D-holes, using a preliminary set of data collected in five other holes, the N- and W-holes during Stages 1 and 2 of the Site Characterization and Validation (SCV) project. Our approach has been to focus on the fracture zones rather than the general set of ubiquitous fractures. Approximately 90% of all the water flowing in the rock is flowing in fracture zones which are neither uniformly conductive nor are they infinitely extensive. Our approach has been to adopt the fracture zone locations as they have been identified with geophysics. We use geologic sense and the original geophysical data to add one zone where significant water inflow has been observed that can not be explained with the other geophysical zones. This report covers LBL's preliminary prediction of flow into the D-holes. Care should be taken in interpreting the results given in this report. As explained below, the approach that LBL has designed for developing a fracture hydrology model requires cross-hole hydrologic data. Cross-hole tests are planned for Stage 3 but were unavailable in Stage 1. As such, we have inferred from available data what a cross-hole test might show and used this synthetic data to make a preliminary calculation of the inflow into the D-holes. Then using all the Stage 3 data we will calculate flow into the Validation Drift itself. The report mainly demonstrates the use of our methodology and the simulated results should be considered preliminary

[Providing of a virtual simulator perineal anatomy (Pelvic Mentor®) in learning pelvic perineology: results of a preliminary study].

Science.gov (United States)

Legendre, G; Sahmoune Rachedi, L; Descamps, P; Fernandez, H

2015-01-01

Medical and surgical simulation is in high demand. It is widely used in North America as a method of education and training of medical students and surgical residents. Learning anatomy and vaginal surgery are based on palpation recognition of different structures. The absence of visual control of actions learners is a limiting factor for the reproducibility of surgical techniques prolapse and urinary incontinenence. However, this reproducibility is the only guarantee of success and safety of these minimally invasive surgeries. We evaluated the contribution of an educational module perineal anatomy using a system combining anatomic mannequin and a computerized 3D virtual simulator (Pelvic Mentor®, Simbionix) in the knowledge of pelvic-perineal anatomical structures for eight residents of obstetrics and gynecology hospitals in Paris. The self-study training module has led to substantial improvements in internal rating with a proportion of structures recognized from 31.25 to 87.5 % (P3D virtual simulator enhances and facilitates learning the anatomy of the pelvic floor. Copyright © 2014 Elsevier Masson SAS. All rights reserved.

Use of the KineSpring system in the treatment of medial knee osteoarthritis: preliminary results.

Science.gov (United States)

Madonna, Vincenzo; Condello, Vincenzo; Piovan, Gianluca; Screpis, Daniele; Zorzi, Claudio

2015-01-01

the purpose of this study was to analyze our preliminary results obtained with the KineSpring system in patients suffering from medial compartment knee osteoarthritis (OA). between September 2012 and May 2014, 53 patients underwent treatment with the KineSpring system. Patient self-assessment was performed pre-operatively and at 3, 6 and 12 months postoperatively, and included the KOOS, Tegner activity score, Lysholm functional knee score, VAS knee pain score, and IKDC score. Device- and procedure-related adverse events were recorded. mean KOOS subscales, except for the Sport/Recreation subscale at six months, improved over time. Mean WOMAC Pain and Function domains, Lysholm score, IKDC score and VAS knee pain score improved over the follow-up period and were significantly improved at 3, 6 and 12 months postoperatively compared to baseline. Mean Tegner score improved slightly over time. In 5 of the 53 (9.4%) patients re-operation was necessary. In 3 patients the device was removed due to infection (one case) or persistent knee pain (two cases). Surgical arthrolysis was performed in two patients. in our preliminary experience, the KineSpring system gave good short-term clinical results. Level IV, therapeutic case series.

Using VIIRS Day/Night Band to Measure Electricity Supply Reliability: Preliminary Results from Maharashtra, India

Directory of Open Access Journals (Sweden)

Michael L. Mann

2016-08-01

Full Text Available Unreliable electricity supplies are common in developing countries and impose large socio-economic costs, yet precise information on electricity reliability is typically unavailable. This paper presents preliminary results from a machine-learning approach for using satellite imagery of nighttime lights to develop estimates of electricity reliability for western India at a finer spatial scale. We use data from the Visible Infrared Imaging Radiometer Suite (VIIRS onboard the Suomi National Polar Partnership (SNPP satellite together with newly-available data from networked household voltage meters. Our results point to the possibilities of this approach as well as areas for refinement. With currently available training data, we find a limited ability to detect individual outages identified by household-level measurements of electricity voltage. This is likely due to the relatively small number of individual outages observed in our preliminary data. However, we find that the approach can estimate electricity reliability rates for individual locations fairly well, with the predicted versus actual regression yielding an R2 > 0.5. We also find that, despite the after midnight overpass time of the SNPP satellite, the reliability estimates derived are representative of daytime reliability.

Preliminary results of the first paleontologic investigations in Uruguayan Antarctica

International Nuclear Information System (INIS)

Perea, D.; Masquelin, E.; Verde, M.; Querequiz, R.

1998-01-01

Preliminary results of the first Uruguayan paleontollogic and biostratigraphical investigations in Antartica are presented. The field work was performed in fildes Peninsula, King George Island, near Uruguayan station Base Cientifica Antarctica Artigas.Some fossiliferous outcrops were geologic and paleontologically analyzed, among them Fossil Hills, situated in the center part of the peninsula, in front of Ardley Island, between the chinese and chilean stations.This hill is composed of fossil bearing piroclastic and epiclastic rocks, assigned to the fossil Hill Fm. Vegetal remains(petrified wood and leaf impronts) were observed and collected in this unit and it is remarkable the presence of Nothofagus sp. and invertebrate trace fossils, Cochlichmus isp and Helminthopsis isp.The depositional environment deduced from the fossil association in lacustrine, under a warm and humid climate.In the same deposits, other investigators have collected aquatic and ratite bird trace fossils. Paleontologic evidence is not contradictory with the Eocene age previously proposed for the studied deposits. (author)

Raman scattering investigation of the water-bridge phenomenon: Some preliminary results

Directory of Open Access Journals (Sweden)

Francesco Aliotta

2010-09-01

Full Text Available A floating water-bridge is formed if a high-voltage direct current is applied between two beakers filled of chemically pure water. Raman spectra of the OH-stretching region have been obtained at ambient condition of temperature and pressure. These preliminary results seem to indicate that the hydrogen-bond structure is only slightly modified by the presence of the electric field applied to form the floating water-bridge in agreement with recent neutron scattering investigation. In fact, the polarized Raman spectrum of the pure water and of the water-bridge is almost superimposable. We are planning to carry out further spectroscopic analysis, at different thermodynamic conditions, for better understanding the role played by the hydrogen-bond in driving the formation of the floating water-bridge.

75 FR 78968 - Magnesium Metal From the Russian Federation: Extension of Time Limit for Preliminary Results of...

Science.gov (United States)

2010-12-17

... DEPARTMENT OF COMMERCE International Trade Administration [A-821-819] Magnesium Metal From the Russian Federation: Extension of Time Limit for Preliminary Results of Antidumping Duty Administrative... administrative review of the antidumping duty order on magnesium metal from the Russian Federation for the period...

77 FR 11065 - Certain Pasta From Turkey: Extension of Time Limit for the Preliminary Results of the...

Science.gov (United States)

2012-02-24

... DEPARTMENT OF COMMERCE International Trade Administration [C-489-806] Certain Pasta From Turkey: Extension of Time Limit for the Preliminary Results of the Countervailing Duty Administrative Review AGENCY... initiation of administrative review of the countervailing duty order on certain pasta from Turkey, covering...

77 FR 15718 - Certain Pasta from Italy: Extension of Time Limit for the Preliminary Results of the...

Science.gov (United States)

2012-03-16

... DEPARTMENT OF COMMERCE International Trade Administration [C-475-819] Certain Pasta from Italy: Extension of Time Limit for the Preliminary Results of the Countervailing Duty Administrative Review AGENCY... notice of initiation of administrative review of the countervailing duty order on certain pasta from...

76 FR 6604 - Certain Pasta From Italy: Extension of Time Limit for the Preliminary Results of the...

Science.gov (United States)

2011-02-07

... DEPARTMENT OF COMMERCE International Trade Administration [C-475-819] Certain Pasta From Italy: Extension of Time Limit for the Preliminary Results of the Countervailing Duty Administrative Review AGENCY... initiation of administrative review of the countervailing duty order on certain pasta from Italy, covering...

77 FR 17410 - Solid Urea From the Russian Federation: Extension of Time Limit for Preliminary Results of...

Science.gov (United States)

2012-03-26

... DEPARTMENT OF COMMERCE International Trade Administration [A-821-801] Solid Urea From the Russian Federation: Extension of Time Limit for Preliminary Results of Antidumping Duty Administrative Review AGENCY... Commerce (the Department) initiated an administrative review of the antidumping duty order on solid urea...

75 FR 19369 - Certain Hot-Rolled Flat-Rolled Carbon Quality Steel Products from Brazil: Preliminary Results of...

Science.gov (United States)

2010-04-14

.... Hot-rolled dual phase steel, phase-hardened, primarily with a ferritic-martensitic microstructure.... See Preliminary Results of Antidumping Duty Administrative Review: Stainless Steel Sheet and Strip in... Antidumping Duty Administrative Review: Stainless Steel Sheet and Strip in Coils From France, 68 FR 69379...

78 FR 55676 - Certain Frozen Fish Fillets From the Socialist Republic of Vietnam: Preliminary Results of the...

Science.gov (United States)

2013-09-11

... DEPARTMENT OF COMMERCE International Trade Administration [A-552-801] Certain Frozen Fish Fillets... order on certain frozen fish fillets (``fish fillets'') from the Socialist Republic of Vietnam... preliminary results. \\1\\ See Notice of Antidumping Duty Order: Certain Frozen Fish Fillets From the Socialist...

78 FR 34340 - Welded Carbon Steel Standard Pipe and Tube Products From Turkey: Preliminary Results of...

Science.gov (United States)

2013-06-07

... Pipe and Tube Products From Turkey: Preliminary Results of Antidumping Duty Administrative Review; 2011... tube products (welded pipe and tube) from Turkey.\\2\\ The period of review is May 1, 2011, to April 30... A.S. (BMB) had reviewable sales during this period of review. DATES: As of June 7, 2013. FOR FURTHER...

Reconstructing the ideal results of a perturbed analog quantum simulator

Science.gov (United States)

Schwenk, Iris; Reiner, Jan-Michael; Zanker, Sebastian; Tian, Lin; Leppäkangas, Juha; Marthaler, Michael

2018-04-01

Well-controlled quantum systems can potentially be used as quantum simulators. However, a quantum simulator is inevitably perturbed by coupling to additional degrees of freedom. This constitutes a major roadblock to useful quantum simulations. So far there are only limited means to understand the effect of perturbation on the results of quantum simulation. Here we present a method which, in certain circumstances, allows for the reconstruction of the ideal result from measurements on a perturbed quantum simulator. We consider extracting the value of the correlator 〈Ôi(t ) Ôj(0 ) 〉 from the simulated system, where Ôi are the operators which couple the system to its environment. The ideal correlator can be straightforwardly reconstructed by using statistical knowledge of the environment, if any n -time correlator of operators Ôi of the ideal system can be written as products of two-time correlators. We give an approach to verify the validity of this assumption experimentally by additional measurements on the perturbed quantum simulator. The proposed method can allow for reliable quantum simulations with systems subjected to environmental noise without adding an overhead to the quantum system.

Preliminary results from MBE-4: A four beam induction linac for heavy ion fusion research

International Nuclear Information System (INIS)

Fessenden, T.J.; Judd, D.L.; Keefe, D.; Kim, C.; Laslett, L.J.; Smith, L.; Warwick, A.I.; Warwick, P.b.A.I.

1986-01-01

Preliminary results are presented from a scaled experimental multiple beam induction linac. This experiment is part of a program of accelerator research for heavy ion fusion. It is shown that multiple beams can be accelerated without significant mutual interaction. Measurements of the longitudinal dynamics of a current-amplifying induction linac are presented and compared to calculations. Coupling of transverse and longitudinal dynamics is discussed

Preliminary results from MBE-4: a four beam induction linac for heavy ion fusion research

International Nuclear Information System (INIS)

Fessenden, T.J.; Judd, D.L.; Keefe, D.; Kim, C.; Laslett, L.J.; Smith, L.; Warwick, A.I.

1986-05-01

Preliminary results are presented from a scaled experimental multiple beam induction linac. This experiment is part of a program of accelerator research for heavy ion fusion. It is shown that multiple beams can be accelerated without significant mutual interaction. Measurements of the longitudinal dynamics of a current-amplifying induction linac are presented and compared to calculations. Coupling of transverse and longitudinal dynamics is discussed

Preliminary results about Electrodeposition of Cobalt at laboratory level

International Nuclear Information System (INIS)

Cornejo, N.

1992-01-01

As of an organic compound, an extraction and Cobalt electrodeposition method had been developed as a part of fabrication aim of a sealed radioactive source with objective to the construction of density meter prototype. It was performed preliminary test of electrodeposition in the laboratory level in a simple cell. The used electrolyte had been a sulphate solution obtained by extraction of an organic solution. It is obtained a Co film by electrodeposition at 55 o C temperature and with an approximately Co concentration in 70 g/lt. (Author) 3 refs., 1 fig., 1 tab

IEA-R1 reactor core simulation with RELAP5 code

International Nuclear Information System (INIS)

Rocha, Ricardo Takeshi Vieira da; Belchior Junior, Antonio; Andrade, Delvonei Alves de; Sabundjian, Gaiane; Umbehaum, Pedro Ernesto; Torres, Walmir Maximo

2005-01-01

This paper presents a preliminary RELAP5 model for the IEA-R1 core. The power distribution is supplied by the neutronic code, CITATION. The main objective is to model the IEA-R1 core and validate the model through the comparison of the results to the ones from COBRA and PARET, which were used in the Final Safety Analysis Report (FSAR) for this plant. Preliminary calculations regarding some simulations are presented. Boundary conditions are simulated through time dependent components. Results obtained are compared to those available for the IEA-R1. This study will be continued considering a model for the whole plant. Important transient and accidents will be analysed in order to verify the Emergency Core Cooling System - ECCS efficiency to hold its function as projected to preserve the integrity of the reactor core and guarantee its cooling. (author)

Most significant preliminary results of the probabilistic safety analysis on the Juragua nuclear power plant

International Nuclear Information System (INIS)

Perdomo, Manuel

1995-01-01

Since 1990 the Group for PSA Development and Applications (GDA/APS) is working on the Level-1 PSA for the Juragua-1 NPP, as a part of an IAEA Technical Assistance Project. The main objective of this study, which is still under way, is to assess, in a preliminary way, the Reactor design safety to find its potential 'weak points' at the construction stage, using a eneric data base. At the same time, the study allows the PSA team to familiarize with the plant design and analysis techniques for the future operational PSA of the plant. This paper presents the most significant preliminary results of the study, which reveal some advantages of the safety characteristics of the plant design in comparison with the homologous VVER-440 reactors and some areas, where including slight modifications would improve the plant safety, considering the level of detail at which the study is carried out. (author). 13 refs, 1 fig, 2 tabs

MOCCA Code for Star Cluster Simulation: Comparison with Optical Observations using COCOA

OpenAIRE

Askar, Abbas; Giersz, Mirek; Pych, Wojciech; Olech, Arkadiusz; Hypki, Arkadiusz

2014-01-01

We introduce and present preliminary results from COCOA (Cluster simulatiOn Comparison with ObservAtions) code for a star cluster after 12 Gyrs of evolution simulated using the MOCCA code. The COCOA code is being developed to quickly compare results of numerical simulations of star clusters with observational data. We use COCOA to obtain parameters of the projected cluster model. For comparison, a FITS file of the projected cluster was provided to observers so that they could use their observ...

75 FR 4779 - Certain Cut-to-Length Carbon-Quality Steel Plate Products From Italy: Preliminary Results of...

Science.gov (United States)

2010-01-29

...-Quality Steel Plate Products From Italy: Preliminary Results of Antidumping Duty Administrative Review... administrative review of the antidumping duty order on certain cut-to-length carbon- quality steel plate products... that the Department conduct an administrative review of its sales and entries of subject merchandise...

75 FR 4044 - Stainless Steel Bar From Brazil: Extension of Time Limit for Preliminary Results of Antidumping...

Science.gov (United States)

2010-01-26

... DEPARTMENT OF COMMERCE International Trade Administration [A-351-825] Stainless Steel Bar From... antidumping duty order on certain stainless steel bar from Brazil for the period February 1, 2008, through... Steel Bar From Brazil: Extension of Time Limit for Preliminary Results of Antidumping Duty...

77 FR 11485 - Certain Pasta From Turkey: Extension of Time Limit for the Preliminary Results of Antidumping...

Science.gov (United States)

2012-02-27

... DEPARTMENT OF COMMERCE International Trade Administration [A-489-805] Certain Pasta From Turkey: Extension of Time Limit for the Preliminary Results of Antidumping Duty Administrative Review AGENCY: Import... initiation of the administrative review of the antidumping duty order on certain pasta from Turkey, covering...

75 FR 81218 - Laminated Woven Sacks From the People's Republic of China: Preliminary Results of the Second...

Science.gov (United States)

2010-12-27

... the People's Republic of China: Preliminary Results of the Second Administrative Review AGENCY: Import... laminated woven sacks (``LWS'') from the People's Republic of China (``PRC'') covering the period August 1, 2009, through July 31, 2010. This review covers imports of subject merchandise from one manufacturer...

77 FR 46030 - Pure Magnesium in Granular Form From the People's Republic of China: Preliminary Results of...

Science.gov (United States)

2012-08-02

... granular magnesium'') from the People's Republic of China (``PRC'') with respect to one producer/ exporter... Form From the People's Republic of China: Preliminary Results of Antidumping Duty Administrative Review...-2012 Administrative Review of Pure Magnesium in Granular Form from the People's Republic of China...

76 FR 13358 - Persulfates From the People's Republic of China: Preliminary Results of the 2009-2010 Antidumping...

Science.gov (United States)

2011-03-11

...'s Republic of China: Preliminary Results of the 2009-2010 Antidumping Duty Administrative Review... conducting an administrative review of the antidumping duty order on persulfates from the People's Republic... review covers one producer/exporter of the subject merchandise, i.e., United Initiators (Shanghai) Co...

76 FR 33194 - Pure Magnesium From the People's Republic of China: Preliminary Results of the 2009-2010...

Science.gov (United States)

2011-06-08

... assessment rates are above de minimis. We invite interested parties to comment on these preliminary results... Determination of Sales at Less Than Fair Value: Antidumping Duty Investigation of Pure Magnesium From the... the following alloying elements: aluminum, manganese, zinc, silicon, thorium, zirconium and rare...

78 FR 69820 - Seamless Refined Copper Pipe and Tube From the People's Republic of China: Preliminary Results...

Science.gov (United States)

2013-11-21

...\\ \\1\\ See Seamless Refined Copper Pipe and Tube From Mexico and the People's Republic of China... and Tube From the People's Republic of China: Preliminary Results and Partial Rescission of... China (``PRC''), covering the period November 1, 2011 through October 31, 2012. The Department has...

Recent improvements in the calculation of prompt fission neutron spectra: Preliminary results

International Nuclear Information System (INIS)

Madland, D.G.; LaBauve, R.J.; Nix, J.R.

1989-01-01

We consider three topics in the refinement and improvement of our original calculations of prompt fission neutron spectra. These are an improved calculation of the prompt fission neutron spectrum N(E) from the spontaneous fission of 252 Cf, a complete calculation of the prompt fission neutron spectrum matrix N(E,E n ) from the neutron-induced fission of 235 U, at incident neutron energies ranging from 0 to 15 MeV, and an assessment of the scission neutron component of the prompt fission neutron spectrum. Preliminary results will be presented and compared with experimental measurements and an evaluation. A suggestion is made for new integral cross section measurements. (author). 45 refs, 12 figs, 1 tab

Preliminary time-phased TWRS process model results

International Nuclear Information System (INIS)

Orme, R.M.

1995-01-01

This report documents the first phase of efforts to model the retrieval and processing of Hanford tank waste within the constraints of an assumed tank farm configuration. This time-phased approach simulates a first try at a retrieval sequence, the batching of waste through retrieval facilities, the batching of retrieved waste through enhanced sludge washing, the batching of liquids through pretreatment and low-level waste (LLW) vitrification, and the batching of pretreated solids through high-level waste (HLW) vitrification. The results reflect the outcome of an assumed retrieval sequence that has not been tailored with respect to accepted measures of performance. The batch data, composition variability, and final waste volume projects in this report should be regarded as tentative. Nevertheless, the results provide interesting insights into time-phased processing of the tank waste. Inspection of the composition variability, for example, suggests modifications to the retrieval sequence that will further improve the uniformity of feed to the vitrification facilities. This model will be a valuable tool for evaluating suggested retrieval sequences and establishing a time-phased processing baseline. An official recommendation on tank retrieval sequence will be made in September, 1995

Preliminary results for the helicity asymmetry E for eta photoproduction on the proton

International Nuclear Information System (INIS)

2012-01-01

Polarization observables are an important tool for clarifying the nucleon resonance spectrum. No previous measurements for double polarization asymmetries have been published for eta photoproduction. Double polarization measurements have been made at Jefferson Lab using a polarized photon beam and protons in a polarized frozen spin target (FROST). Data were taken during the first running period of FROST using the CLAS detector with photon energies from 0.33 to 2.35 GeV. Preliminary results for the E polarization observable for eta meson photoproduction from the proton at threshold and above, along with comparisons to several theoretical predictions are presented.

Postmortem study of stable carbon isotope ratios in human cerebellar DNA: preliminary results

International Nuclear Information System (INIS)

Slatkin, D.N.; Irsa, A.P.; Friedman, L.

1978-01-01

It is observed that 13 C/ 12 C ratios in tissue specimens removed postmortem in the United States and Canada are significantly different from corresponding ratios in European specimens. On the basis of this information, measurements of carbon isotope ratios in DNA isolated from cerebella of native-born and European-born North Americans are in progress with the goal of estimating the average lifetime rate of DNA turnover in human neurons. Preliminary results from twenty postmortem examinations are consistent with the hypothesis that a significant proportion of human cerebellar DNA is renewed during the lifetime of an individual

76 FR 17380 - Solid Urea From the Russian Federation: Extension of Time Limit for Preliminary Results of...

Science.gov (United States)

2011-03-29

... DEPARTMENT OF COMMERCE International Trade Administration [A-821-801] Solid Urea From the Russian Federation: Extension of Time Limit for Preliminary Results of Antidumping Duty Administrative Review AGENCY... administrative review of the antidumping duty order on solid urea from the Russian Federation for the period July...

75 FR 13495 - Saccharin from the People's Republic of China: Preliminary Results of the 2008-2009 Antidumping...

Science.gov (United States)

2010-03-22

... Republic of China: Preliminary Results of the 2008-2009 Antidumping Duty Administrative Review AGENCY... administrative review of the antidumping duty order on saccharin from the People's Republic of China (``PRC'') covering the period July 1, 2008, through June 30, 2009. This administrative review covers one exporter of...

DoSSiER: Database of Scientific Simulation and Experimental Results

CERN Document Server

Wenzel, Hans; Genser, Krzysztof; Elvira, Daniel; Pokorski, Witold; Carminati, Federico; Konstantinov, Dmitri; Ribon, Alberto; Folger, Gunter; Dotti, Andrea

2017-01-01

The Geant4, GeantV and GENIE collaborations regularly perform validation and regression tests for simulation results. DoSSiER (Database of Scientific Simulation and Experimental Results) is being developed as a central repository to store the simulation results as well as the experimental data used for validation. DoSSiER can be easily accessed via a web application. In addition, a web service allows for programmatic access to the repository to extract records in json or xml exchange formats. In this article, we describe the functionality and the current status of various components of DoSSiER as well as the technology choices we made.

The Myres Hill remote sensing intercomparison study: preliminary results

Energy Technology Data Exchange (ETDEWEB)

Clive, P J M; Chindurza, I [SgurrEnergy Ltd, 79 Coplaw Street, Glasgow G42 7JG, Scotland (United Kingdom); Ravey, I; Bass, J [RES Group Ltd, James Blyth House, 7000 Academy Park, Glasgow, Scotland (United Kingdom); Boyle, R J; Jones, P [TUV NEL Ltd, East Kilbride, Glasgow G75 0QF, Scotland (United Kingdom); Lang, S J [Sustainable Energy Research Group, University College Cork (Ireland); Bradley, S [Mighty River Power, Level 14, 23-29 Albert Street, Auckland (New Zealand); Hay, L [Garrad Hassan and Partners Ltd, 2064 Maryhill Road, Glasgow G20 0AB, Scotland (United Kingdom); Oldroyd, A [Oldbaum Services Ltd, Schoolhouse, Brig o' Turk, Callander, Scotland (United Kingdom); Stickland, M [University of Strathclyde, 16 Richmond Street, Glasgow G1 1XQ, Scotland (United Kingdom)], E-mail: peter.clive@sgurrenergy.com

2008-05-01

Two remote sensing techniques (SODAR and LIDAR) have been developed for measuring wind speed and turbulence from ground level up to altitudes of 300 m or higher. Although originally developed in the defence sector, these techniques are now generating considerable interest in the renewable energy and meteorological sectors. Despite the benefits of these instruments they are not yet generally accepted for due diligence measurements by wind energy developers and financial institutions. There is a requirement for a series of independent assessments of these new metrology techniques, comparing their measurements with the approved cup-type anemometer readings. This is being addressed at TUV NEL's Myres Hill wind turbine test site in a measurement programme supported by the DIUS National Measurement Systems Measurement for Innovators scheme and a consortium of 21 industrial collaborators. Data from SODAR and LIDAR systems are being compared with results from cup-type anemometers mounted at different heights on an 80m meteorological mast. An ultrasonic sensor is also mounted on the mast. The objective of the test programme is to assess the effectiveness of SODAR and LIDAR wind speed measurement techniques under different operating regimes and atmospheric conditions. Results from the measurements will provide definitive data on the performance of the remote wind speed sensing techniques under test on complex terrain typical of many wind farm sites. Preliminary measurements based on data acquired during the initial measurement campaign are presented.

Hybridization among wild boars, local breeds and commercial breeds - preliminary results

DEFF Research Database (Denmark)

Iacolina, Laura; Bakan, Jana; Cubric-Curik, Vlatka

. Hybridization with the domestic pig is known to occur in Europe, however the degree and extent of the phenomenon is not fully understood yet. Introgression is considered to be a treat to biodiversity and could lead to loss of local adaptation or introgression in the wild population of human selected genes....... A better understanding of the hybridization levels at European scale would provide an important tool for the development of management plans aimed at reducing human conflict but also at preserving biodiversity and genetic differentiation. Additionally, this information would provide new perspectives...... gradients in variability levels among the analysed wild and domestic populations. This preliminary results will be further investigated to address the possible presence of hybrid zone(s) in Europe and the possible implications for conservation and management of both wild populations and local pig breeds...

Validation of safeguards monitoring systems and their simulations

International Nuclear Information System (INIS)

Standley, V.; Boeck, H.; Villa, M.

2001-01-01

Research is underway at the Atominstitut in Vienna Austria where the objective is to design and validate quantitatively a safeguards monitoring system (SMS) and its simulation. The work is novel because the simulation is also used as the basis for automated evaluation of SMS data. Preliminary results indicate that video and radiation data can be automatically interpreted using this approach. Application of the technique promises that an investment in a simulation supports directly the safeguards objective, which is to catch diversion of nuclear material. Consequently, it is easier for a safeguards agency to also realize other benefits associated with simulation-based acquisition, in addition to having a quantitative method for validation

Preliminary results of the XR2-1 experiment

International Nuclear Information System (INIS)

Gauntt, R.O.; Helmick, P.H.; Humphries, L.

1996-01-01

The XR2-1 (Ex-Reactor) experiment, investigating metallic core-melt relocation in boiling water reactor geometry, was performed on October 12, 1995, following two previous simpler XR1-series tests in August and November of 1993. The XR2-1 test made use of a highly detailed replication of the lower region of the BWR core, including the control blade and channel box structures, fuel rods, fuel canister nosepieces, control blade velocity limiter, and fuel support pieces, in order to investigate a key core melt progression uncertainty for BWR Station Blackout type accidents. The purpose of this experiment program is to examine the behavior of downward-draining molten metallic core materials in a severe reactor accident in a dry BWR core, and to determine conditions under which the molten materials drain out of the core region, or freeze to form blockages in the lower portion of the core. In the event that the draining metallic materials do not form stable blockages in the lower core region, and instead erode the lower core structures such as the lower core plate, then the subsequent core melt progression processes may proceed quite differently than was observed in the TMI-2 accident, with correspondingly different impact on vessel loading and vessel release behavior. The results of the Ex-Reactor tests are preliminary. All of the tests conducted have shown a significant degree of channel box destruction induced by the draining control blade materials. The XR2-1 test further showed that the draining zircaloy melt causes significant disruption of the fuel rod geometry. All of the tests have shown tendencies to form interim blockages as the melts temporarily freeze, but that these blockages re-melt, assisted by eutectic interactions, resulting in the sudden draining of accumulated metallic melt pools

Preliminary results of hydrologic testing: The composite Umtanum basalt flow top at borehole RRL-2 (3,568 - 3,781 feet)

International Nuclear Information System (INIS)

Strait, S.R.; Spane, F.A. Jr.

1982-11-01

This report presents preliminary results and description of hydrologic test activities for the composite Umtanum basalt flow top (3,568--3,781 feet) at Borehole RRL-2. Hydrologic tests conducted include two constant discharge air-lift and four slug tests. Preliminary results indicate an observed hydraulic head for the test interval of 405.7 feet above mean sea level. Transmissivity values determined from hydrologic tests performed, range between 244 to 481 ft 2 /day, with an assigned best estimate of 480 ft 2 /day. The best estimate of equivalent hydraulic conductivity, based on an effective test thickness of 157 feet, is 3.1 ft/day. 7 refs., 9 figs., 3 tabs

Preliminary Results from the PrimEx-II experiment at Jefferson Lab

Energy Technology Data Exchange (ETDEWEB)

Gasparian, Ashot [NCA& T, Greensboro, NC; Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States)

2016-06-01

Properties of the neutral pion, as the lightest hadron in Nature, are most sensitive to the basic symmetries and their partial breaking effects in the theory of the strong interaction (QCD). In particular, the po →gg decay width is primarily defined by the spontaneous chiral symmetry breaking effect (chiral anomaly) in QCD. The next order corrections to the anomaly have been shown to be small and are known to a 1% precision level. The PrimEx Collaboration at JLab has developed and performed two Primakoff type experiments to measure the po →gg decay width with a similar precision. The published result from the PrimEx-I experiment, G(p0 →gg ) = 7.82±0.14 (stat.)±0.17 (syst.) eV, was a factor of two more precise than the average value quoted in PDG-2010 [1]. The second experiment was performed in 2010 with a goal of 1.4% total uncertainty to address the next-to-leading-order theory calculations. The preliminary results from the PrimEx-II experiment are presented and discussed in this note.

A PRELIMINARY JUPITER MODEL

International Nuclear Information System (INIS)

Hubbard, W. B.; Militzer, B.

2016-01-01

In anticipation of new observational results for Jupiter's axial moment of inertia and gravitational zonal harmonic coefficients from the forthcoming Juno orbiter, we present a number of preliminary Jupiter interior models. We combine results from ab initio computer simulations of hydrogen–helium mixtures, including immiscibility calculations, with a new nonperturbative calculation of Jupiter's zonal harmonic coefficients, to derive a self-consistent model for the planet's external gravity and moment of inertia. We assume helium rain modified the interior temperature and composition profiles. Our calculation predicts zonal harmonic values to which measurements can be compared. Although some models fit the observed (pre-Juno) second- and fourth-order zonal harmonics to within their error bars, our preferred reference model predicts a fourth-order zonal harmonic whose absolute value lies above the pre-Juno error bars. This model has a dense core of about 12 Earth masses and a hydrogen–helium-rich envelope with approximately three times solar metallicity

A PRELIMINARY JUPITER MODEL

Energy Technology Data Exchange (ETDEWEB)

Hubbard, W. B. [Lunar and Planetary Laboratory, The University of Arizona, Tucson, AZ 85721 (United States); Militzer, B. [Department of Earth and Planetary Science, Department of Astronomy, University of California, Berkeley, CA 94720 (United States)

2016-03-20

In anticipation of new observational results for Jupiter's axial moment of inertia and gravitational zonal harmonic coefficients from the forthcoming Juno orbiter, we present a number of preliminary Jupiter interior models. We combine results from ab initio computer simulations of hydrogen–helium mixtures, including immiscibility calculations, with a new nonperturbative calculation of Jupiter's zonal harmonic coefficients, to derive a self-consistent model for the planet's external gravity and moment of inertia. We assume helium rain modified the interior temperature and composition profiles. Our calculation predicts zonal harmonic values to which measurements can be compared. Although some models fit the observed (pre-Juno) second- and fourth-order zonal harmonics to within their error bars, our preferred reference model predicts a fourth-order zonal harmonic whose absolute value lies above the pre-Juno error bars. This model has a dense core of about 12 Earth masses and a hydrogen–helium-rich envelope with approximately three times solar metallicity.

Preliminary results from a crowdsourcing experiment in immunohistochemistry.

Science.gov (United States)

Della Mea, Vincenzo; Maddalena, Eddy; Mizzaro, Stefano; Machin, Piernicola; Beltrami, Carlo A

2014-01-01

Crowdsourcing, i.e., the outsourcing of tasks typically performed by a few experts to a large crowd as an open call, has been shown to be reasonably effective in many cases, like Wikipedia, the Chess match of Kasparov against the world in 1999, and several others. The aim of the present paper is to describe the setup of an experimentation of crowdsourcing techniques applied to the quantification of immunohistochemistry. Fourteen Images from MIB1-stained breast specimens were first manually counted by a pathologist, then submitted to a crowdsourcing platform through a specifically developed application. 10 positivity evaluations for each image have been collected and summarized using their median. The positivity values have been then compared to the gold standard provided by the pathologist by means of Spearman correlation. Contributors were in total 28, and evaluated 4.64 images each on average. Spearman correlation between gold and crowdsourced positivity percentages is 0.946 (p crowdsourcing for an image analysis task that is currently time-consuming when done by human experts. Crowdsourced work can be used in various ways, in particular statistically agregating data to reduce identification errors. However, in this preliminary experimentation we just considered the most basic indicator, that is the median positivity percentage, which provided overall good results. This method might be more aimed to research than routine: when a large number of images are in need of ad-hoc evaluation, crowdsourcing may represent a quick answer to the need.

Research Initiatives and Preliminary Results In Automation Design In Airspace Management in Free Flight

Science.gov (United States)

Corker, Kevin; Lebacqz, J. Victor (Technical Monitor)

1997-01-01

The NASA and the FAA have entered into a joint venture to explore, define, design and implement a new airspace management operating concept. The fundamental premise of that concept is that technologies and procedures need to be developed for flight deck and ground operations to improve the efficiency, the predictability, the flexibility and the safety of airspace management and operations. To that end NASA Ames has undertaken an initial development and exploration of "key concepts" in the free flight airspace management technology development. Human Factors issues in automation aiding design, coupled aiding systems between air and ground, communication protocols in distributed decision making, and analytic techniques for definition of concepts of airspace density and operator cognitive load have been undertaken. This paper reports the progress of these efforts, which are not intended to definitively solve the many evolving issues of design for future ATM systems, but to provide preliminary results to chart the parameters of performance and the topology of the analytic effort required. The preliminary research in provision of cockpit display of traffic information, dynamic density definition, distributed decision making, situation awareness models and human performance models is discussed as they focus on the theme of "design requirements".

Development of methods to measure hemoglobin adducts by gel electrophoresis - Preliminary results

International Nuclear Information System (INIS)

Sun, J.D.; McBride, S.M.

1988-01-01

Chemical adducts formed on blood hemoglobin may be a useful biomarker for assessing human exposures to these compounds. This paper reports preliminary results in the development of methods to measure such adducts that may be generally applicable for a wide variety of chemicals. Male F344/N rats were intraperitoneally injected with 14 C-BaP dissolved in corn oil. Twenty-four hours later, the rats were sacrificed. Blood samples were collected and globin was isolated. Globin protein was then cleaved into peptide fragments using cyanogen bromide and the fragments separated using 2-dimensional gel electrophoresis. The results showed that the adducted 14 C-globin fragments migrated to different areas of the gel than did unadducted fragments. Further research is being conducted to develop methods that will allow quantitation of separated adducted globin fragments from human blood samples without the use of a radiolabel. (author)

MSFC Stream Model Preliminary Results: Modeling Recent Leonid and Perseid Encounters

Science.gov (United States)

Cooke, William J.; Moser, Danielle E.

2004-01-01

The cometary meteoroid ejection model of Jones and Brown (1996b) was used to simulate ejection from comets 55P/Tempel-Tuttle during the last 12 revolutions, and the last 9 apparitions of 109P/Swift-Tuttle. Using cometary ephemerides generated by the Jet Propulsion Laboratory s (JPL) HORIZONS Solar System Data and Ephemeris Computation Service, two independent ejection schemes were simulated. In the first case, ejection was simulated in 1 hour time steps along the comet s orbit while it was within 2.5 AU of the Sun. In the second case, ejection was simulated to occur at the hour the comet reached perihelion. A 4th order variable step-size Runge-Kutta integrator was then used to integrate meteoroid position and velocity forward in time, accounting for the effects of radiation pressure, Poynting-Robertson drag, and the gravitational forces of the planets, which were computed using JPL s DE406 planetary ephemerides. An impact parameter was computed for each particle approaching the Earth to create a flux profile, and the results compared to observations of the 1998 and 1999 Leonid showers, and the 1993 and 2004 Perseids.

New cysteamine (2-chloroethyl)nitrosoureas. Synthesis and preliminary antitumor results.

Science.gov (United States)

Madelmont, J C; Godeneche, D; Parry, D; Duprat, J; Chabard, J L; Plagne, R; Mathe, G; Meyniel, G

1985-09-01

Three chemical pathways were used for the synthesis of four new N'-(2-chloroethyl)-N-[2-(methylsulfinyl)ethyl]- and N'-(2-chloroethyl)-N-[2-(methylsulfonyl)ethyl]-N- or N'-nitrosoureas. These compounds are plasma metabolites of CNCC, a promising antineoplastic (2-chloroethyl)nitrosourea. Preliminary antitumor evaluation was performed against L1210 leukemia implanted intraperitoneally in mice. Among these compounds, two of them exhibited a greater antitumor activity compared to that of the parent mixture.

77 FR 73417 - Diamond Sawblades and Parts Thereof From the People's Republic of China: Preliminary Results of...

Science.gov (United States)

2012-12-10

... Thereof From the People's Republic of China: Preliminary Results of Antidumping Duty Administrative Review... Republic of China (``PRC''). The period of review (``POR'') is November 1, 2010 through October 31, 2011... have been calculated in accordance with section 772 of the Act. Because the PRC is a nonmarket economy...

77 FR 73015 - Circular Welded Non-Alloy Steel Pipe From the Republic of Korea: Preliminary Results of...

Science.gov (United States)

2012-12-07

... Steel Pipe From the Republic of Korea: Preliminary Results of Antidumping Duty Administrative Review... antidumping duty order on circular welded non-alloy steel pipe (CWP) from the Republic of Korea (Korea). The... preliminarily found that one respondent has made sales of the subject merchandise at prices below normal value...

Results of preliminary experiments on tritium decontamination by UV irradiation

International Nuclear Information System (INIS)

Oya, Yasuhisa; Shu, Wataru; O'hira, Shigeru; Hayashi, Takumi; Nishi, Masataka

2000-03-01

In the point of view of protection of workers from the radiation exposure and the limitation of the contamination with radioactive materials, it is important to decontaminate mobile tritium from plasma facing components of a nuclear fusion reactor at the beginning of their maintenance work. It is considered that the heating is the most effective method for decontamination. However, it is important to develop new decontamination method of adsorbed hydro-carbon based substances from the materials that cannot be heated or the inner pipe of double pipes. This report presents results of preliminary experiments performed for the development of the effective tritium decontamination technique pursuing under US/Japan collaborative program on technology for fusion-fuel processing (Annex IV). In the experiments, the effects of Ultra Violet (UV) irradiation on tritium removal from some kinds of materials, such as poly vinyl chloride -(CH 2 CHCl) n - film, polyethylene film and graphite samples coated by C 2 H 2 plasma were examined. As the result of UV irradiation, it was confined that hydrogen and carbon based compounds could be released from the specimen during UV irradiation. It is concluded that UV irradiation is one of the hopeful candidates for effective tritium decontamination. (author)

Tracking simulation and wire chamber requirements for the SSC

International Nuclear Information System (INIS)

Hanson, G.G.; Niczyporuk, B.B.; Palounek, A.P.T.

1988-11-01

Limitations placed on wire chambers by radiation damage and rate requirements in the SSC environment are reviewed. Possible conceptual designs for wire chamber tracking systems which meet these requirements are discussed. Computer simulation studies of tracking in such systems are presented. Simulations of events from interesting physics at the SSC, including hits from minimum bias background events, are examined. Results of some preliminary pattern recognition studies are given. 16 refs., 16 figs., 2 tabs

IRIS PRA preliminary results and future direction

International Nuclear Information System (INIS)

Finnicum, D.J.; Kling, C.L.; Carelli, M.D.

2004-01-01

Westinghouse is currently conducting the pre-application licensing of the International Reactor Innovative and Secure (IRIS) on behalf of the IRIS Consortium. One of the key aspects of the IRIS design is the concept of safety-by-design. The PRA (Probabilistic Risk Analysis) is being used as an integral part of the design process. As part of this effort, a PRA of the initial design was generated to address 2 key areas. First, the IRIS PRA supported the evaluation of IRIS design issues by providing a solid risk basis for design and analyses required for the pre-licensing evaluation of the IRIS design. The PRA provides the tool for quantifying the benefit of the safety-by-design approach. Second, the current PRA task is beginning the preparation of the more complete PRA analyses and documentation eventually required for Design Certification. One of the key risk-related goals for IRIS is to reduce the EPZ (Emergency Protection Zone) to within the exclusion area by demonstrating that the off-site doses are consistent with the US Protective Action Guidelines (PAGs) for initiation of emergency response so that the required protective actions would be limited to the exclusion area. The results of the preliminary PRA indicated a core damage frequency of 1.2 E-08 for internal initiators. This is a very good result but much work is needed to meet the ambitious goal of no emergency response. The next phase of the PRA analyses will involve a two-fold expansion of the PRA. First, as the design and analyses approach a greater level of detail, the assumptions used for the initial PRA will be reviewed and the models will be revised as needed to reflect the improved knowledge of the system design and performance. Furthermore, as the full plant design advances, the PRA will be expanded to incorporate risk associated with external challenges such as seismic and fire, and to address low power and shutdowns modes of operation. As with the initial work, the PRA will serve as a tool to

A combination of preliminary results on gauge boson couplings measured by the LEP Experiments

CERN Document Server

CERN. Geneva

2004-01-01

This note presents a combination of published and preliminary measurements of triple gauge boson couplings (TGCs) and quartic gauge boson couplings (QGCs) from the four LEP experiments. We give an updated combination of the charged TGCs, g1z, kg and lg in single and multi-parameter fits. Updated results from the QGCs from the ZZgg vertex, ac/Lambda^2 and a0/Lambda^2, are given as well. The combinations of neutral TGCs hiv anf fiv are also presented, including an updated fiv combination.

Modeling of Particle Acceleration at Multiple Shocks Via Diffusive Shock Acceleration: Preliminary Results

Science.gov (United States)

Parker, L. N.; Zank, G. P.

2013-12-01

Successful forecasting of energetic particle events in space weather models require algorithms for correctly predicting the spectrum of ions accelerated from a background population of charged particles. We present preliminary results from a model that diffusively accelerates particles at multiple shocks. Our basic approach is related to box models (Protheroe and Stanev, 1998; Moraal and Axford, 1983; Ball and Kirk, 1992; Drury et al., 1999) in which a distribution of particles is diffusively accelerated inside the box while simultaneously experiencing decompression through adiabatic expansion and losses from the convection and diffusion of particles outside the box (Melrose and Pope, 1993; Zank et al., 2000). We adiabatically decompress the accelerated particle distribution between each shock by either the method explored in Melrose and Pope (1993) and Pope and Melrose (1994) or by the approach set forth in Zank et al. (2000) where we solve the transport equation by a method analogous to operator splitting. The second method incorporates the additional loss terms of convection and diffusion and allows for the use of a variable time between shocks. We use a maximum injection energy (Emax) appropriate for quasi-parallel and quasi-perpendicular shocks (Zank et al., 2000, 2006; Dosch and Shalchi, 2010) and provide a preliminary application of the diffusive acceleration of particles by multiple shocks with frequencies appropriate for solar maximum (i.e., a non-Markovian process).

Spatial and temporal variation of radiocarbon in tree rings - some preliminary results

International Nuclear Information System (INIS)

Higham, T.F.G.; Hogg, A.G.; McCormac, F.G.; Baillie, M.G.L.; Brown, D.; Palmer, J.G.; Xiong, L.

1997-01-01

A number of researchers have identified a measurable difference between the 14 C activities of tree rings of identical dendochronological age between the Northern and the Southern Hemispheres. It is also acknowledged that there is an urgent need for new high precision Δ 14 C data from tree rings in both Hemispheres to help resolve the questions relating to the magnitude and cause of the locality and temporal dependence of the Δ 14 C record, to provide a reliable Southern Hemisphere calibration curve and to throw light upon the 1986 and 1993 Calibration data set discrepancies. In this paper, the authors present the research design of a project to investigate these critical issues in radiocarbon age calibration and describe the preliminary results

Modelling lung cancer due to radon and smoking in WISMUT miners: Preliminary results

International Nuclear Information System (INIS)

Bijwaard, H.; Dekkers, F.; Van Dillen, T.

2011-01-01

A mechanistic two-stage carcinogenesis model has been applied to model lung-cancer mortality in the largest uranium-miner cohort available. Models with and without smoking action both fit the data well. As smoking information is largely missing from the cohort data, a method has been devised to project this information from a case-control study onto the cohort. Model calculations using 256 projections show that the method works well. Preliminary results show that if an explicit smoking action is absent in the model, this is compensated by the values of the baseline parameters. This indicates that in earlier studies performed without smoking information, the results obtained for the radiation parameters are still valid. More importantly, the inclusion of smoking-related parameters shows that these mainly influence the later stages of lung-cancer development. (authors)

The influence of the preliminary garter spring spacer simulator clamping force in the pressure tube spacer -calandria tube hook-up simulator aging behaviour

International Nuclear Information System (INIS)

Gyongyosi, T.; Deloreanu, G.; Puiu, D.; Corbescu, B.; Anghel, N.; Dinu, E.

2016-01-01

The garter spring spacer is a specially constructed torsion spring used to fit-out the CANDU 6 fuel channel. The pressure tube ageing decreases the gap to the calandria tube. Continuous gap decrease directly affects the garter spring spacers behavior during fuel channel assembly operation. The preliminary clamping force value of the garter spring spacer assembly is important for its ageing behavior. This paper briefly describes the experimental technological facilities used for conducted the experiments and highlights some of the important moments during an experiment carried out in laboratory conditions, without using pressurized boiled water and irradiation working conditions. The results analysis and some conclusions are outlined at the end, pointing out that a garter spring spacer preliminary clamping force increase reduces the vibration response signal amplitude, and does not lead to its relaxation. The paper is dedicated to specialists working in research and technological engineering. (authors)

76 FR 41759 - Fresh Garlic From the People's Republic of China: Extension of Time Limit for Preliminary Results...

Science.gov (United States)

2011-07-15

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-831] Fresh Garlic From the People's Republic of China: Extension of Time Limit for Preliminary Results of Antidumping Duty... (``Department'') published a notice of initiation of an administrative review of fresh garlic from the People's...

75 FR 32361 - Fresh Garlic From The People's Republic of China: Extension of Time Limit for Preliminary Results...

Science.gov (United States)

2010-06-08

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-831] Fresh Garlic From The People's Republic of China: Extension of Time Limit for Preliminary Results of Antidumping Duty... Commerce (``Department'') published a notice of initiation of an administrative review of fresh garlic from...

76 FR 65496 - Certain Orange Juice From Brazil; Notice of Extension of Time Limits for Preliminary Results of...

Science.gov (United States)

2011-10-21

... DEPARTMENT OF COMMERCE International Trade Administration [A-351-840] Certain Orange Juice From Brazil; Notice of Extension of Time Limits for Preliminary Results of Antidumping Duty Administrative... antidumping duty order on certain orange juice from Brazil. See Initiation of Antidumping and Countervailing...

75 FR 69917 - Certain Orange Juice From Brazil; Notice of Extension of Time Limits for Preliminary Results of...

Science.gov (United States)

2010-11-16

... DEPARTMENT OF COMMERCE International Trade Administration [A-351-840] Certain Orange Juice From Brazil; Notice of Extension of Time Limits for Preliminary Results of Antidumping Duty Administrative... antidumping duty order on certain orange juice from Brazil. See Initiation of Antidumping and Countervailing...

Monte Carlo simulation for the transport beamline

Energy Technology Data Exchange (ETDEWEB)

Romano, F.; Cuttone, G.; Jia, S. B.; Varisano, A. [INFN, Laboratori Nazionali del Sud, Via Santa Sofia 62, Catania (Italy); Attili, A.; Marchetto, F.; Russo, G. [INFN, Sezione di Torino, Via P.Giuria, 1 10125 Torino (Italy); Cirrone, G. A. P.; Schillaci, F.; Scuderi, V. [INFN, Laboratori Nazionali del Sud, Via Santa Sofia 62, Catania, Italy and Institute of Physics Czech Academy of Science, ELI-Beamlines project, Na Slovance 2, Prague (Czech Republic); Carpinelli, M. [INFN Sezione di Cagliari, c/o Dipartimento di Fisica, Università di Cagliari, Cagliari (Italy); Tramontana, A. [INFN, Laboratori Nazionali del Sud, Via Santa Sofia 62, Catania, Italy and Università di Catania, Dipartimento di Fisica e Astronomia, Via S. Sofia 64, Catania (Italy)

2013-07-26

In the framework of the ELIMED project, Monte Carlo (MC) simulations are widely used to study the physical transport of charged particles generated by laser-target interactions and to preliminarily evaluate fluence and dose distributions. An energy selection system and the experimental setup for the TARANIS laser facility in Belfast (UK) have been already simulated with the GEANT4 (GEometry ANd Tracking) MC toolkit. Preliminary results are reported here. Future developments are planned to implement a MC based 3D treatment planning in order to optimize shots number and dose delivery.

Monte Carlo simulation for the transport beamline

International Nuclear Information System (INIS)

Romano, F.; Cuttone, G.; Jia, S. B.; Varisano, A.; Attili, A.; Marchetto, F.; Russo, G.; Cirrone, G. A. P.; Schillaci, F.; Scuderi, V.; Carpinelli, M.; Tramontana, A.

2013-01-01

In the framework of the ELIMED project, Monte Carlo (MC) simulations are widely used to study the physical transport of charged particles generated by laser-target interactions and to preliminarily evaluate fluence and dose distributions. An energy selection system and the experimental setup for the TARANIS laser facility in Belfast (UK) have been already simulated with the GEANT4 (GEometry ANd Tracking) MC toolkit. Preliminary results are reported here. Future developments are planned to implement a MC based 3D treatment planning in order to optimize shots number and dose delivery

Preliminary Results of 3D-DDTC Pixel Detectors for the ATLAS Upgrade

Energy Technology Data Exchange (ETDEWEB)

La Rosa, Alessandro; /CERN; Boscardin, M.; /Fond. Bruno Kessler, Povo; Dalla Betta, G.-F.; /Trento U. /INFN, Trento; Darbo, G.; Gemme, C.; /INFN, Genoa; Pernegger, H.; /CERN; Piemonte, C.; /Fond. Bruno Kessler, Povo; Povoli, M.; /Trento U. /INFN, Trento; Ronchin, S.; /Fond. Bruno Kessler, Povo; Zoboli, A.; /Trento U. /INFN, Trento; Zorzi, N.; /Fond. Bruno Kessler, Povo; Bolle, E.; /Oslo U.; Borri, M.; /INFN, Turin /Turin U.; Da Via, C.; /Manchester U.; Dong, S.; /SLAC; Fazio, S.; /Calabria U.; Grenier, P.; /SLAC; Grinstein, S.; /Barcelona, IFAE; Gjersdal, H.; /Oslo U.; Hansson, P.; /SLAC; Huegging, F.; /Bonn U. /SLAC /INFN, Turin /Turin U. /Oslo U. /Bergen U. /Oslo U. /Prague, Tech. U. /Bonn U. /SUNY, Stony Brook /Bonn U. /SLAC

2012-04-04

3D Silicon sensors fabricated at FBK-irst with the Double-side Double Type Column (DDTC) approach and columnar electrodes only partially etched through p-type substrates were tested in laboratory and in a 1.35 Tesla magnetic field with a 180 GeV pion beam at CERN SPS. The substrate thickness of the sensors is about 200 {mu}m, and different column depths are available, with overlaps between junction columns (etched from the front side) and ohmic columns (etched from the back side) in the range from 110 {mu}m to 150 {mu}m. The devices under test were bump bonded to the ATLAS Pixel readout chip (FEI3) at SELEX SI (Rome, Italy). We report leakage current and noise measurements, results of functional tests with Am{sup 241} {gamma}-ray sources, charge collection tests with Sr90 {beta}-source and an overview of preliminary results from the CERN beam test.

Radon and radon daughters' concentration in spring and wells waters from Presidente Prudente: preliminary results

International Nuclear Information System (INIS)

Osorio, Ana Maria Araya; Saenz, Carlos Alberto Tello; Pereira, Luiz Augusto Stuani

2009-01-01

This work presents the preliminary results about the concentration of radon and radon daughters in wells and springs water from Presidente Prudente. Six water samples were studied: three from well-water, two from springs water and one from potable water. For the determination of α-activity the samples were placed inside plastic containers where the CR-39 tracks detectors were outside the water. The track density of α-particles were measured by using optical microscopy. The results show that one sample from well-water presented higher concentration of radon and radon daughters than the other samples. (author)

A physiological production model for cacao : results of model simulations

NARCIS (Netherlands)

Zuidema, P.A.; Leffelaar, P.A.

2002-01-01

CASE2 is a physiological model for cocoa (Theobroma cacao L.) growth and yield. This report introduces the CAcao Simulation Engine for water-limited production in a non-technical way and presents simulation results obtained with the model.

A new gas stripper system for BARC-TIFR Pelletron Accelerator facility: installation and preliminary results

International Nuclear Information System (INIS)

Sharma, S.C.; Ninawe, N.G.; Yadav, M.L.; Ekambaram, M.; Ramjilal; Matkar, U.V.; Ansari, Q.N.; Lokare, R.N.; Ramlal; Gupta, A.K.; Bhagwat, P.V.; Pillay, R.G.

2009-01-01

The gas-stripper plays a key role in stripping the heavy and molecular ion beams in a tandem accelerator. Efficiency of gas stripper depends on its supporting vacuum pumps. A new recirculating turbo molecular pump-based gas stripper has been installed in the high voltage terminal of Pelletron Accelerator. Re-circulating the stripper gas reduces the flow of gas into the accelerating tubes reducing the transmission losses. Preliminary results obtained using the new gas stripper system are discussed. (author)

Stock Market Reaction to CEO Appointment – Preliminary Results

Directory of Open Access Journals (Sweden)

Katarzyna Byrka-Kita

2017-06-01

Full Text Available Purpose: The aim of this paper is to examine shareholders’ reaction to the decision of the supervisory board to appoint a CEO in companies listed on the Warsaw Stock Exchange. Methodology: An event study and the mean-adjusted model were applied. The abnormal returns were measured as the CAAR in the entire (-60, + 60 window and selected sub-windows. Findings: The obtained values of abnormal returns indicate the shareholder’s negative reaction. Throughout the observation window, they oscillate slightly below zero, and in the window (0, +20 they are negative at -1.566%. Irrespective of the observation window, negative abnormal returns were obtained for over half of the observation (52–57%. Therefore, preliminary results indicate the predominance of the information effect over the real one. The decrease in market value as a result of the event may result from an increase in investors’ uncertainty as to the effects of changes in strategy and skills of the new CEO. Originality: The research is a unique one. To date, no one has carried out research into shareholders’ reaction to a CEO appointment in either the Polish or Central and Eastern European capital markets. They primarily bring the value of cognition of shareholders’ behaviour in the analysed event, which is reflected in share prices. They extend the literature on the signalization instruments, i.e. the activities that boards can undertake due to the new information transmitted to the capital market participants and stakeholders. The market reaction to a CEO appointment will without a doubt interest investors; the institutions responsible for supervision (which in the case of Poland is the Financial Oversight Commission and the legislator in charge of regulations that prevent insider trading while promoting corporate disclosure transparency.

Ocean Thermal Energy Conversion power system development. Phase I: preliminary design. Final report. [ODSP-3 code; OTEC Steady-State Analysis Program

Energy Technology Data Exchange (ETDEWEB)

1978-12-04

The following appendices are included; Dynamic Simulation Program (ODSP-3); sample results of dynamic simulation; trip report - NH/sub 3/ safety precautions/accident records; trip report - US Coast Guard Headquarters; OTEC power system development, preliminary design test program report; medium turbine generator inspection point program; net energy analysis; bus bar cost of electricity; OTEC technical specifications; and engineer drawings. (WHK)

75 FR 65449 - Stainless Steel Bar From India: Extension of Time Limit for the Preliminary Results of the...

Science.gov (United States)

2010-10-25

... DEPARTMENT OF COMMERCE International Trade Administration [A-533-810] Stainless Steel Bar From India: Extension of Time Limit for the Preliminary Results of the Antidumping Duty Administrative Review... initiation of an administrative review of the antidumping duty order on stainless steel bar from India...

77 FR 12008 - Certain Pasta From Italy: Extension of Time Limit for the Preliminary Results of Antidumping Duty...

Science.gov (United States)

2012-02-28

... DEPARTMENT OF COMMERCE International Trade Administration [A-475-818] Certain Pasta From Italy: Extension of Time Limit for the Preliminary Results of Antidumping Duty Administrative Review AGENCY: Import... notice of initiation of the administrative review of the antidumping duty order on certain pasta from...

Simulation of radioactive waste transmutation on the t.node parallel computer

International Nuclear Information System (INIS)

Bacha, F.; Maillard, J.; Silva, J.

1995-01-01

Before any experiment on reactor driven by an accelerator, computer simulation supplies tools for optimization. Some of the key parameters are neutron production on a heavy target and neutronic distribution flux in the core. During two code benchmarks organized by the NEA-OECD, simulations of energetic incident proton collisions on a thin lead target for the first one, on a thick lead target for the second one, are described. One validation of the numeric codes is based on these results. A preliminary design of a burning waste system using benchmark result analysis and fission focused simulations is proposed

Simulation of radioactive waste transmutation on the T. Node parallel computer

International Nuclear Information System (INIS)

Bacha, F.; Maillard, J.; Silva, J.

1995-01-01

Before any experiment on reactor driven by an accelerator, computer simulation supplies tools for optimization. Some of the key parameters are neutron production on a heavy target and neutronic distribution flux in the core. During two code benchmarks organized by the NEA-OECD, simulations of energetic incident proton collisions on a thin lead target for the first one, on a thick lead target for the second one, are described. One validation of our numeric codes is based on these results. A preliminary design of a burning waste system using benchmark result analysis and fission focused simulations is proposed

Simulation of radioactive waste transmutation on the t.node parallel computer

Energy Technology Data Exchange (ETDEWEB)

Bacha, F.; Maillard, J.; Silva, J. [LPC College de France, Paris (France)

1995-10-01

Before any experiment on reactor driven by an accelerator, computer simulation supplies tools for optimization. Some of the key parameters are neutron production on a heavy target and neutronic distribution flux in the core. During two code benchmarks organized by the NEA-OECD, simulations of energetic incident proton collisions on a thin lead target for the first one, on a thick lead target for the second one, are described. One validation of the numeric codes is based on these results. A preliminary design of a burning waste system using benchmark result analysis and fission focused simulations is proposed.

ADREA-I: A transient three dimensional transport code for atmospheric and other applications - some preliminary results

International Nuclear Information System (INIS)

Bartzis, G.

1985-02-01

In this work a general description of the ADREA-I code is presented and some preliminary results are discussed. The ADREA-I is a transient three dimensional computer code aimed at transport analysis with particular emphasis on atmospheric dispersion under any realistic terrain conditions (complex or not) applicable to the planetary boundary layer in a distance extending up to a hundred kilometers or more. The complex geometry applications and the reasonable results obtained constitute a solid indication of the broad capability of the code. (author)

Non-invasive approach towards the in vivo estimation of 3D inter-vertebral movements: methods and preliminary results.

Science.gov (United States)

Cerveri, P; Pedotti, A; Ferrigno, G

2004-12-01

A kinematical model of the lower spine was designed and used to obtain a robust estimation of the vertebral rotations during torso movements from skin-surface markers recorded by video-cameras. Markers were placed in correspondence of the anatomical landmarks of the pelvic bone and vertebral spinous and transverse processes, and acquired during flexion, lateral bending and axial motions. In the model calibration stage, a motion-based approach was used to compute the rotation axes and centres of the functional segmental units. Markers were mirrored into virtual points located on the model surface, expressed in the local reference system of coordinates. The spine motion assessment was solved into the domain of extended Kalman filters: at each frame of the acquisition, the model pose was updated by minimizing the distances between the measured 2D marker projections on the cameras and the corresponding back-projections of virtual points located on the model surface. The novelty of the proposed technique rests on the fact that the varying location of the rotation centres of the functional segmental units can be tracked directly during motion computation. In addition, we show how the effects of skin artefacts on orientation data can be taken into account. As a result, the kinematical estimation of simulated motions shows that orientation artefacts were reduced by a factor of at least 50%. Preliminary experiments on real motion confirmed the reliability of the proposed method with results in agreement with classical studies in literature.

Spatial and temporal variation of radiocarbon in tree rings - some preliminary results

Energy Technology Data Exchange (ETDEWEB)

Higham, T.F.G.; Hogg, A.G. [Waikato Univ., Hamilton (New Zealand); McCormac, F.G.; Baillie, M.G.L.; Brown, D. [Queens`s University, Belfast, (Ireland). School of Geosciences; Palmer, J.G.; Xiong, L. [Lincoln University, Canterbury (New Zealand). Department of Plant Science

1997-12-31

A number of researchers have identified a measurable difference between the {sup 14}C activities of tree rings of identical dendochronological age between the Northern and the Southern Hemispheres. It is also acknowledged that there is an urgent need for new high precision {Delta}{sup 14}C data from tree rings in both Hemispheres to help resolve the questions relating to the magnitude and cause of the locality and temporal dependence of the {Delta}{sup 14}C record, to provide a reliable Southern Hemisphere calibration curve and to throw light upon the 1986 and 1993 Calibration data set discrepancies. In this paper, the authors present the research design of a project to investigate these critical issues in radiocarbon age calibration and describe the preliminary results. Paper no. 30; Extended abstract; 12 refs.

ACTPol: Status and preliminary CMB polarization results from the Atacama Cosmology Telescope

Science.gov (United States)

Koopman, Brian

2014-03-01

The Atacama Cosmology Telescope Polarimeter (ACTPol) is a polarization sensitive upgrade for the Atacama Cosmology Telescope, located at an elevation of 5190 m on Cerro Toco in Chile. In summer 2013, ACTPol achieved first light with one third of the final detector configuration. The remaining two thirds of the detector array will be installed during spring 2014, enabling full sensitivity, high resolution, observations at both 90 GHz and 150 GHz. Using approximately 3,000 transition-edge sensor bolometers, ACTPol will enable measurements of small angular scale polarization anisotropies in the Cosmic Microwave Background (CMB). I will present a status update for the ACTPol receiver and some preliminary results. ACTPol measurements will allow us to probe the spectral index of inflation as well as to constrain early dark energy and the sum of neutrino masses.

Simulation and performance of brushless dc motor actuators

Science.gov (United States)

Gerba, A., Jr.

1985-12-01

The simulation model for a Brushless D.C. Motor and the associated commutation power conditioner transistor model are presented. The necessary conditions for maximum power output while operating at steady-state speed and sinusoidally distributed air-gap flux are developed. Comparison of simulated model with the measured performance of a typical motor are done both on time response waveforms and on average performance characteristics. These preliminary results indicate good agreement. Plans for model improvement and testing of a motor-driven positioning device for model evaluation are outlined.

Mastoidectomy simulation with combined visual and haptic feedback.

Science.gov (United States)

Agus, Marco; Giachetti, Andrea; Gobbetti, Enrico; Zanetti, Gianluigi; Zorcolo, Antonio; John, Nigel W; Stone, Robert J

2002-01-01

Mastoidectomy is one of the most common surgical procedures relating to the petrous bone. In this paper we describe our preliminary results in the realization of a virtual reality mastoidectomy simulator. Our system is designed to work on patient-specific volumetric object models directly derived from 3D CT and MRI images. The paper summarizes the detailed task analysis performed in order to define the system requirements, introduces the architecture of the prototype simulator, and discusses the initial feedback received from selected end users.

MOCCA code for star cluster simulation: comparison with optical observations using COCOA

Science.gov (United States)

Askar, Abbas; Giersz, Mirek; Pych, Wojciech; Olech, Arkadiusz; Hypki, Arkadiusz

2016-02-01

We introduce and present preliminary results from COCOA (Cluster simulatiOn Comparison with ObservAtions) code for a star cluster after 12 Gyr of evolution simulated using the MOCCA code. The COCOA code is being developed to quickly compare results of numerical simulations of star clusters with observational data. We use COCOA to obtain parameters of the projected cluster model. For comparison, a FITS file of the projected cluster was provided to observers so that they could use their observational methods and techniques to obtain cluster parameters. The results show that the similarity of cluster parameters obtained through numerical simulations and observations depends significantly on the quality of observational data and photometric accuracy.

Preliminary results of hydrologic testing of the Umtanum Basalt Fracture Zone at borehole RRL-2 (3,781 to 3,827 ft)

International Nuclear Information System (INIS)

Strait, S.R.; Spane, F.A. Jr.

1983-02-01

This report presents preliminary results and description of hydrologic test activities for the Umtanum Basalt Fracture Zone at Borehole RRL-2, within the test interval 3,781 to 3,827 feet. Hydrologic tests conducted include two short-term, constant discharge pumping tests and two slug tests. Preliminary results indicate an observed hydraulic head for the test interval of 406.7 feet above mean sea level. Transmissivity values determined from hydrologic tests performed range between 205 and 881 ft 2 /day. The best estimate of equivalent hydraulic conductivity, based on an effective test thickness of 6 feet, is 147 ft/day. 8 refs., 6 figs., 3 tabs

UAS Integration in the NAS Project: Part Task 6 V & V Simulation: Primary Results

Science.gov (United States)

Rorie, Conrad; Fern, Lisa; Shively, Jay; Santiago, Confesor

2016-01-01

This is a presentation of the preliminary results on final V and V (Verification and Validation) activity of [RTCA (Radio Technical Commission for Aeronautics)] SC (Special Committee)-228 DAA (Detect and Avoid) HMI (Human-Machine Interface) requirements for display alerting and guidance.

Criteria for safety related nuclear plant operator actions: a preliminary assessment of available data

International Nuclear Information System (INIS)

Haas, P.M.; Bott, T.F.

1982-01-01

The need for a quantitative data base on the reliability of nuclear power plant operators has long been recognised by human factors and reliability analysts, and the great need for further assessment of operator performance under accident conditions has been dramatically emphasised by the incident at Three Mile Island-2. In the US, an effort has been under way for a number of years to develop a design standard to define when required manual operator action can be accepted as part of a nuclear plant design basis. To provide the necessary data base to support such standards and the necessary quantitative assessment of operator reliability, the US Nuclear Regulatory Commission is sponsoring a study at Oak Ridge National Laboratory to develop the data base. A preliminary assessment, completed in April 1979, concluded that sufficient data from US operating experience did not exist to provide an adequate data base. A programme of research using full-scope nuclear plant simulators and results that are correlated to field data was suggested. That programme was recently initiated. This paper reviews the approach, results and conclusions of the preliminary assessment and summarises the planned research programme of simulator studies. (author)

Simulation Study of Flap Effects on a Commercial Transport Airplane in Upset Conditions

Science.gov (United States)

Cunningham, Kevin; Foster, John V.; Shah, Gautam H.; Stewart, Eric C.; Ventura, Robin N.; Rivers, Robert A.; Wilborn, James E.; Gato, William

2005-01-01

As part of NASA's Aviation Safety and Security Program, a simulation study of a twinjet transport airplane crew training simulation was conducted to address fidelity for upset or loss of control conditions and to study the effect of flap configuration in those regimes. Piloted and desktop simulations were used to compare the baseline crew training simulation model with an enhanced aerodynamic model that was developed for high-angle-of-attack conditions. These studies were conducted with various flap configurations and addressed the approach-to-stall, stall, and post-stall flight regimes. The enhanced simulation model showed that flap configuration had a significant effect on the character of departures that occurred during post-stall flight. Preliminary comparisons with flight test data indicate that the enhanced model is a significant improvement over the baseline. Some of the unrepresentative characteristics that are predicted by the baseline crew training simulation for flight in the post-stall regime have been identified. This paper presents preliminary results of this simulation study and discusses key issues regarding predicted flight dynamics characteristics during extreme upset and loss-of-control flight conditions with different flap configurations.

Preliminary results of aerosols' properties studied with EPF measurements from the SPICAM/UV instrument

Science.gov (United States)

Willame, Yannick; Carine Vandaele, Ann; Depiesse, Cedric; Gillotay, Didier; Kochenova, Svetlana; Montmessin, Franck

2013-04-01

Aerosols on Mars have an important impact on the radiative transfer properties of its atmosphere. Today their spectral properties and therefore their interaction with UV radiation are only poorly known. Improving the radiative transfer modeling requires a better knowledge of their characteristics, in particular of their opacity, phase function and single scattering albedo. Part of such information can be accessed by using EPF observations. The SPICAM instrument on board of the Mars-Express satellite is a 2 channel spectrometer. One channel operates in the ultraviolet (118-320 nm) and the second one in the infrared (1.0-1.7μm). SPICAM has been orbiting around the red planet since 2003 and has thus provided a large set of data. The instrument is capable of measuring under different geometries (nadir, limb, occultation) and one of them, called EPF (Emission Phase Function), can be a tool to study aerosols' properties. We have developed a new retrieval algorithm for nadir measurements based on the radiative transfer model LIDORT. This new code performs simulations of spectra taking into account gas absorption, surface reflection and scattering by aerosols and gases. The retrieval method, based on the optimal estimation, allows us up to now to deduce the ozone column density, the aerosols' optical depth and the surface albedo (with fixed wavelength dependencies). We are developing our model further in order to better study the aerosols' characteristics using EPF observations, which consist in looking at the same point on the planet while the satellite moves along the orbit. As the attempt to study all the aerosols' properties simultaneously was not convincing, we started studying their opacity and the influence of its altitude distribution with the other characteristics fixed. We will present preliminary results of our study on aerosols' properties using EPF data from SPICAM.

Spectral Monitoring of AGN: Preliminary Results for Ark 564 and Arp 102B

Directory of Open Access Journals (Sweden)

Shapovalova A. I.

2011-09-01

Full Text Available We present preliminary results of the long-term spectral monitoring of two active galactic nuclei with different broad line shapes: Ark 564 and Arp 102B. Ark 564 is a bright nearby narrow-line Syfert 1 (NLS1 galaxy with relatively narrow permitted optical emission lines and a high Fe II/Hβ ratio, while Arp 102B is a nearby broad-line radio galaxy with broad double-peaked Balmer emission lines. The spectra of Ark 564 were observed during 11-year period (1999-2009 and the spectra of Arp 102B in the 12-year period (1998-2009, with SAO 6 m and 1 m telescopes (Russia and the OAGH 2.1 m telescope (Cananea, Mexico.

Preliminary Results from Integrating Compton Photon Polarimetry in Hall A of Jefferson Lab

International Nuclear Information System (INIS)

Parno, D; Friend, M; Benmokhtar, F; Franklin, G; Quinn, B; Michaels, R; Nanda, S; Souder, P

2011-01-01

A wide range of nucleon and nuclear structure experiments in Jefferson Lab's Hall A require precise, continuous measurements of the polarization of the electron beam. In our Compton polarimeter, electrons are scattered off photons in a Fabry-Perot cavity; by measuring an asymmetry in the integrated signal of the scattered photons detected in a GSO crystal, we can make non-invasive, continuous measurements of the beam polarization. Our goal is to achieve 1% statistical error within two hours of running. We discuss the design and commissioning of an upgrade to this apparatus, and report preliminary results for experiments conducted at beam energies from 3.5 to 5.9 GeV and photon rates from 5 to 100 kHz.

Assessment of genuine and simulated dissociative identity disorder on the structured interview of reported symptoms.

Science.gov (United States)

Brand, Bethany L; McNary, Scot W; Loewenstein, Richard J; Kolos, Amie C; Barr, Stefanie R

2006-01-01

Little is known about how to detect malingered dissociative identity disorder (DID). This study presents preliminary data from an ongoing study about the performance of DID patients on the Structured Interview of Reported Symptoms (SIRS, Rogers, Bagby, & Dickens, 1992), considered to be a "gold standard" structured interview in forensic psychology to detect feigning of psychological symptoms. Test responses from 20 dissociative identity disorder (DID) patients are compared to those of 43 well informed and motivated DID simulators. Both the simulators and DID patients endorsed such a high number of symptoms that their average overall scores would typically be interpreted as indicative of feigning. The simulators' mean scores were significantly higher than those of the DID patients on only four out of 13 scales. These results provide preliminary evidence that well informed and motivated simulators are able to fairly successfully simulate DID patients and avoid detection on the SIRS. Furthermore, many DID patients may be at risk for being inaccurately labeled as feigning on the SIRS.

Life span studies on mice exposed to heavy charged particles or photons: preliminary results

International Nuclear Information System (INIS)

Ainsworth, E.J.

1980-01-01

This chapter summarizes the results currently available where dose-dependent mortality is compared among the single cohort that received fractionated doses of carbon ions and the first replicate that received single doses. At this time, 17% mortality has occurred in both groups and had enhanced life shortening been produced by fractionation of the carbon ion dose, somewhat higher mortality might be expected. Cautious interpretation of these preliminary results is necessary, but the mortality data available at this time provides no evidence for enhancement by dose fractionation with carbon ions. In sum, at this time, it appears the Q factor used for fission spectrum neutrons could be conservative if it were used for assessment of risk following exposure to 400 MeV carbon ions

High Fidelity BWR Fuel Simulations

Energy Technology Data Exchange (ETDEWEB)

Yoon, Su Jong [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-08-01

This report describes the Consortium for Advanced Simulation of Light Water Reactors (CASL) work conducted for completion of the Thermal Hydraulics Methods (THM) Level 3 milestone THM.CFD.P13.03: High Fidelity BWR Fuel Simulation. High fidelity computational fluid dynamics (CFD) simulation for Boiling Water Reactor (BWR) was conducted to investigate the applicability and robustness performance of BWR closures. As a preliminary study, a CFD model with simplified Ferrule spacer grid geometry of NUPEC BWR Full-size Fine-mesh Bundle Test (BFBT) benchmark has been implemented. Performance of multiphase segregated solver with baseline boiling closures has been evaluated. Although the mean values of void fraction and exit quality of CFD result for BFBT case 4101-61 agreed with experimental data, the local void distribution was not predicted accurately. The mesh quality was one of the critical factors to obtain converged result. The stability and robustness of the simulation was mainly affected by the mesh quality, combination of BWR closure models. In addition, the CFD modeling of fully-detailed spacer grid geometry with mixing vane is necessary for improving the accuracy of CFD simulation.

Properties of ABNT 41xx and 86xx cast steel modified with niobium; evaluation methodology and experimental preliminary results

International Nuclear Information System (INIS)

Suzczynski, E.F.; Chatterjee, S.; Mueller, Arno

1982-01-01

The experimental methodology to evaluate the mechanical properties of ABNT 41xx and 86xx steels modified with NB in the as cast and heat treated conditions and the first preliminary results obtained in a laboratory scale, are presented. (Author) [pt

CFD simulation on condensation inside a Hybrid SIT

Energy Technology Data Exchange (ETDEWEB)

Jeon, Byong Guk; Ryu, Sung Uk; Kim, Seok; Euh, Dong Jin [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

The concept of Hybrid Safety Injection Tank system (Hybrid SIT) was proposed by Korea Atomic Energy Research Institute (KAERI) aiming at Advanced Power Reactor Plus. The main advantage of the system is the ready injection of coolant into the reactor coolant system at high pressure. In this paper, a CFD simulation is conducted as a preliminary study. In Hybrid SITs, condensation inside the tank affects its pressure rise and injection time. In an attempt to explore the condensation in detail, we manufactured a dedicated experimental facility for visualization of condensation-induced thermal mixing and conducted a preliminary CFD simulation. Its condensation models were validated first and then computational domain was constructed. The water region was modeled as a solid for stable calculation. The CFD results gave less condensation and excessive pressurization because of lack of steam penetration into the water. In the future, the water region will be modeled as liquid using a VOF model.

MAAP4 CANDU analysis of a generic CANDU-6 plant: preliminary results

Energy Technology Data Exchange (ETDEWEB)

Petoukhov, S.M.; Mathew, P.M

2001-10-01

To support the generic probabilistic safety analysis (PSA) program at AECL, in particular to conduct Level 2 PSA analysis of a CANDU 6 plant undergoing a postulated severe accident, the capability to conduct severe accident consequence analysis for a CANDU plant is required. For this purpose, AECL selected MAAP4 CANDU from a number of other severe accident codes. The necessary models for a generic CANDU 6 station have been implemented in the code, and the code version 0.2 beta was tested using station data, which were assembled for a generic CANDU 6 station. This paper describes the preliminary results of the consequence analysis using MAAP4 CANDU for a generic CANDU 6 station, when it undergoes a station blackout and a large loss-of-coolant accident scenario. The analysis results show that the plant response is consistent with the physical phenomena modeled and the failure criteria used. The results also confirm that the CANDU design is robust with respect to severe accidents, which is reflected in the calculated long times that are available for administering accident management measures to arrest the accident progression before the calandria vessel or containment become at risk. (author)

Comparison between the performance of some KEK-klystrons and simulation results

Energy Technology Data Exchange (ETDEWEB)

Fukuda, Shigeki [National Lab. for High Energy Physics, Tsukuba, Ibaraki (Japan)

1997-04-01

Recent developments of various klystron simulation codes have enabled us to realistically design klystrons. This paper presents various simulation results using the FCI code and the performances of tubes manufactured based on this code. Upgrading a 30-MW S-band klystron and developing a 50-MW S-band klystron for the KEKB projects are successful examples based on FCI-code predictions. Mass-productions of these tubes have already started. On the other hand, a discrepancy has been found between the FCI simulation results and the performance of real tubes. In some cases, the simulation results lead to high-efficiency results, while manufactured tubes show the usual value, or a lower value, of the efficiency. One possible cause may come from a data mismatch between the electron-gun simulation and the input data set of the FCI code for the gun region. This kind of discrepancy has been observed in 30-MW S-band pulsed tubes, sub-booster pulsed tubes and L-band high-duty pulsed klystrons. Sometimes, JPNDSK (one-dimensional disk-model code) gives similar results. Some examples using the FCI code are given in this article. An Arsenal-MSU code could be applied to the 50-MW klystron under collaboration with Moscow State University; a good agreement has been found between the prediction of the code and performance. (author)

Preliminary results with the CLAMSUD pion spectrometer at the Moscow Meson Factory

International Nuclear Information System (INIS)

Badala, A.; Barbera, R.; Librizzi, F.; Longhitano, A.; Nicotra, D.; Palmeri, A.; Pappalardo, G.S.; Riggi, F.; Santoro, A.; Turrisi, R.; Aseev, V.; Feschenko, A.; Gavrilov, Yu.; Guber, F.; Golubeva, M.; Karavicheva, T.; Kurepin, A.; Ostroumov, P.; Potapov, V.; Tiflov, V.; Zhuravlev, A.

1995-01-01

A magnetic spectrometer has been recently installed at the new proton beam facility of the Moscow Meson Factory, to study charged pion production from proton-nucleus interactions at 200-400 MeV bombarding energy. Preliminary reults obtained during the first runs are reported. The planned physics program is also discussed. (orig.)

Preliminary Results on the Influence of Engineered Artificial Mucus Layer on Phonation

Science.gov (United States)

Döllinger, Michael; Gröhn, Franziska; Berry, David A.; Eysholdt, Ulrich; Luegmair, Georg

2014-01-01

Purpose: Previous studies have confirmed the influence of dehydration and an altered mucus (e.g., due to pathologies) on phonation. However, the underlying reasons for these influences are not fully understood. This study was a preliminary inquiry into the influences of mucus architecture and concentration on vocal fold oscillation. Method: Two…

Results of Preliminary Tests of PAR Bunch Cleaning

CERN Document Server

Yao, Chihyuan; Grelick, Arthur; Lumpkin, Alex H; Sereno, Nicholas S

2005-01-01

A particle accumulator ring (PAR) is used at the Advanced Photon Source (APS) to collect multiple linac bunches and compress them into a 0.3-ns (rms) single bunch for booster injection. A 9.77-MHz fundamental rf system and a 117.3-MHz harmonic rf system are employed for initial beam capture and bunch length compression. Satellite bunches with very low charge form due to rf phase drifts or beam loading change. These satellites, when injected into the booster and then into the storage ring (SR), cause bunch impurity at three buckets from the target bucket. Storage ring and booster bunch cleaning was tried but proved to be difficult due to the top-up mode of operation in the storage ring and tune drift in the booster synchrotron. Recently we implemented a PAR bunch-cleaning system with tune-modulated harmonic rf knockout. Preliminary tests gave a measured SR bunch purity of better than 10

77 FR 33395 - Light-Walled Rectangular Pipe and Tube From Turkey: Notice of Preliminary Results of Antidumping...

Science.gov (United States)

2012-06-06

... Noksel did not make sales at less than normal value (NV) during the POR. If these preliminary results are... chromium, or 0.30 percent of cobalt, or 0.40 percent of lead, or 1.25 percent of nickel, or 0.30 percent of... questionnaire and 19 CFR 351.414(e)(2), Noksel requested that the reporting period for home market sales be...

The MACHO Project: Preliminary Results from 4 years of SMC observations.

Science.gov (United States)

Vandehei, T.; Griest, K.; Lehner, M.; Alcock, C.; Alves, D.; Cook, K.; Marshall, S.; Minniti, D.; Allsman, R.; Axelrod, T.; Freeman, K.; Peterson, B.; Rodgers, A.; Pratt, M.; Becker, A.; Stubbs, C.; Tomaney, A.; Bennett, D.; Quinn, P.; Sutherland, W.; Welch, D.

1997-12-01

The MACHO project is a search for dark matter in the form of massive compact halo objects(MACHOs). The project has photometrically monitored tens of millions of stars in the Large Magellanic Cloud (LMC), Small Magellanic Cloud (SMC), and Galactic bulge in search of rare gravitational microlensing events caused by these otherwise invisible objects. Microlensing toward the LMC has allowed powerful statements to be made about the dark population in the halo of our Galaxy, indicating that the MACHO halo fraction could be as high as f=0.5 with a most probable MACHO mass being ~ 0.5Msun. However, to date the LMC has been the only line of sight out of our Galaxy's halo. Clearly, another line of sight would provide a consistency check on these results, as well as another contraint on models of the halo, in particular on halo flattening. The SMC affords us this second line of sight. Here we give a status report on our upcoming 4 year results toward the SMC. We present the results of a preliminary analysis on over 2.2 million stars from 3 square degrees and discuss the implications for the dark matter in the halo of our Galaxy. A detailed analysis of the microlensing candidates toward the SMC, with blending and parallax fits, will be shown. This work is dedicated to the memory of Alex Rodgers.

Persian competing word test: Development and preliminary results in normal children

Directory of Open Access Journals (Sweden)

Mohammad Ebrahim Mahdavi

2008-12-01

Full Text Available Background and Aim: Assessment of central auditory processing skills needs various behavioral tests in format of a test battery. There is a few Persian speech tests for documenting central auditory processing disorders. The purpose of this study was developing a dichotic test formed of one-syllabic words suitable for evaluation of central auditory processing in Persian language children and reporting its preliminary results in a group of normal children.Materials and Methods: Persian words in competing manner test was developed utilizing most frequent monosyllabic words in children storybooks reported in the previous researches. The test was performed at MCL on forty-five normal children (39 right-handed and 6 left-handed aged 5-11 years. The children did not show any obvious problem in hearing, speech, language and learning. Free (n=28 and directed listening (n=17 tasks were investigated.Results: The results show that in directed listening task, there is significant advantage for performance of pre-cued ear relative to opposite side. Right ear advantage is evident in free recall condition. Average performance of the children in directed recall is significantly better than free recall. Average row score of the test increases with the children age.Conclusion: Persian words in competing manner test as a dichotic test, can show major characteristics of dichotic listening and effect of maturation of central auditory system on it in normal children.

First results from simulations of supersymmetric lattices

Science.gov (United States)

Catterall, Simon

2009-01-01

We conduct the first numerical simulations of lattice theories with exact supersymmetry arising from the orbifold constructions of \\cite{Cohen:2003xe,Cohen:2003qw,Kaplan:2005ta}. We consider the Script Q = 4 theory in D = 0,2 dimensions and the Script Q = 16 theory in D = 0,2,4 dimensions. We show that the U(N) theories do not possess vacua which are stable non-perturbatively, but that this problem can be circumvented after truncation to SU(N). We measure the distribution of scalar field eigenvalues, the spectrum of the fermion operator and the phase of the Pfaffian arising after integration over the fermions. We monitor supersymmetry breaking effects by measuring a simple Ward identity. Our results indicate that simulations of Script N = 4 super Yang-Mills may be achievable in the near future.

Preliminary clinical results of locoregional hyperthermia for primary and secondary bone tumors

Energy Technology Data Exchange (ETDEWEB)

Zhu, J.L.; Nagata, Yasushi; Kanamori, Shuichi; Mitsumori, Michihide; Okuno, Yoshishige; Horii, Naotoshi; Nishimura, Yasumasa; Masunaga, Shinitiro; Hiraoka, Masahiro [Kyoto Univ. (Japan). Graduate School of Medicine

2000-03-01

Nineteen primary and secondary bone tumors in 16 patients were treated with hyperthermia plus radiotherapy and/or chemotherapy between 1982 and 1997 at Kyoto University Hospital. The thermometric and clinical results were analyzed retrospectively. In 55 of 86 hyperthermia sessions, the intratumor temperature was measured using a thermometer. Of the 19 tumors, 16 (84%) received heat treatment 4-7 times, and 3 (16%) received 1 or 2 treatments of hyperthermia. The mean maximum, mean minimum and average intratumor temperatures were 42.9, 40.4 and 41.6 deg C, respectively, and 12 (67%) reached a tumor maximum temperature above 42.5 deg C. The durations that intratumor points exceeded 42, 41 and 40 deg C were 27, 34 and 38 min, respectively. The local tumor response to treatment was assessed using X-ray computed tomography. The local response rate was 16% and the local pain relief rate was 63%. The 1-year cumulative survival rate was 60%. Our preliminary results indicated that thermoradiotherapy and thermochemotherapy are clinicaly feasible and potentially beneficial in the management of locally advanced bone tumors. (author)

Simulation of some nonstationary astrophysical processes in laser-produced-plasma experiments

International Nuclear Information System (INIS)

Antonov, V.M.; Zakharov, Yu.P.; Orishich, A.M.; Ponomarenko, A.G.; Posukh, V.G.

1985-01-01

Preliminary results and calibration are reported on the astrophysical plasma dynamics simulator. This apparatus creates a spherical plasma cloud by the irradiation of a perlon filament target from two radial opposite directions by pulses of highly ionized background plasma in a high-vacuum chamber with diameter of 1.2 m and length of 5 m. The spherical plasma cloud simulates the exploding peripheric part of a supernova, expanding into the interstellar medium. (author)

Advanced Helmet Mounted Display (AHMD) for simulator applications

Science.gov (United States)

Sisodia, Ashok; Riser, Andrew; Bayer, Michael; McGuire, James P.

2006-05-01

The Advanced Helmet Mounted Display (AHMD), augmented reality visual system first presented at last year's Cockpit and Future Displays for Defense and Security conference, has now been evaluated in a number of military simulator applications and by L-3 Link Simulation and Training. This paper presents the preliminary results of these evaluations and describes current and future simulator and training applications for HMD technology. The AHMD blends computer-generated data (symbology, synthetic imagery, enhanced imagery) with the actual and simulated visible environment. The AHMD is designed specifically for highly mobile deployable, minimum resource demanding reconfigurable virtual training systems to satisfy the military's in-theater warrior readiness objective. A description of the innovative AHMD system and future enhancements will be discussed.

Research results for the applications of high power ion beams

International Nuclear Information System (INIS)

Yang Hailiang; Qiu Aici; Sun Jianfeng; He Xiaoping; Tang Junping; Wang Haiyang; Zhang Jiasheng; Xu Ri; Peng Jianchang; Ren Shuqing; Li Peng; Yang Li; Huang Jianjun; Zhang Guoguang; Ouyang Xiaoping; Li Hongyu

2003-01-01

The results obtained in the theoretical and experimental studies for the application of high power ion beams in certain areas of nuclear physics and material science are reported. The preliminary experimental results of generating 6-7 MeV quasi-monoenergetic pulsed γ-rays with high power pulsed proton beams striking 19 F target on the Flash II accelerator are presented. By placing the target far enough downstream, the quasi-monoenergetic pulsed γ-rays can be discriminated experimentally from the diode Bremsstrahlung. This article also describes the other applications of high power ion beams and the preliminary experimental and theoretical results in simulation of soft X-ray thermal-mechanical effects, generation of high intense pulsed neutrons, equation of state and shock-wave physics experiments, surface modification and so on

Constraining back-arc basin formation in the eastern Coral Sea: preliminary results from the ECOSAT voyage

Science.gov (United States)

Seton, M.; Williams, S.; Mortimer, N. N.; Meffre, S.; Moore, J.; Micklethwaite, S.; Zahirovic, S.

2013-12-01

The eastern Coral Sea region is an underexplored area at the northeastern corner of the Australian plate, where long-lived interaction between the Pacific and Australian plate boundaries has resulted in an intricate assemblage of deep oceanic basins and ridges, continental fragments and volcanic products. A paucity of marine geophysical and geological data from this complex region has resulted in the lack of a clear conceptual framework to describe its formation, ultimately affecting our understanding of the connection between the plate boundaries of the SW Pacific and SE Asia. In particular, the tectonic relationship between two back-arc basins, the Santa Cruz and d'Entrecasteaux Basins, and the South Rennell Trough, has yet to be resolved. In October-November, 2012, we collected 6,200 km of marine magnetic, 6,800 km of gravity and over 13,600 km2 of swath bathymetry data from the eastern Coral Sea onboard the RV Southern Surveyor. A complementary dredging program yielded useful samples from 14 seafloor sites. Our preliminary geochemical interpretation of the dredge samples obtained from the South Rennell Trough reveal volcanic rocks resembling MORB or BABB-type basalts, similar in composition to the recently re-analysed and dated ORSTOM dredges from the area that yielded ~28 Ma MORB-like basalts. Swath bathymetry profiles from the Santa Cruz Basin reveal that the South Rennell Trough extends into this basin, with seafloor spreading fabric being parallel to the trough. Preliminary analysis of the three full and four partial new magnetic anomaly profiles across the Santa Cruz Basin, coupled with limited existing profiles, reveals that the basin may have formed between Chrons 13-18 (~32-38 Ma), with an extinct spreading ridge along the inferred continuation of the South Rennell Trough, consistent with ORSTOM age dates. Our results suggest that the South Rennell Trough is an extinct southwestward propagating spreading ridge, which may have initiated along a pre

Direct Numerical Simulations of Rayleigh-Taylor instability

International Nuclear Information System (INIS)

Livescu, D; Wei, T; Petersen, M R

2011-01-01

The development of the Rayleigh-Taylor mixing layer is studied using data from an extensive new set of Direct Numerical Simulations (DNS), performed on the 0.5 Petaflops, 150k compute cores BG/L Dawn supercomputer at Lawrence Livermore National Laboratory. This includes a suite of simulations with grid size of 1024 2 × 4608 and Atwood number ranging from 0.04 to 0.9, in order to examine small departures from the Boussinesq approximation as well as large Atwood number effects, and a high resolution simulation of grid size 4096 2 × 4032 and Atwood number of 0.75. After the layer width had developed substantially, additional branched simulations have been run under reversed and zero gravity conditions. While the bulk of the results will be published elsewhere, here we present preliminary results on: 1) the long-standing open question regarding the discrepancy between the numerically and experimentally measured mixing layer growth rates and 2) mixing characteristics.

A Morphing Technique Applied to Lung Motions in Radiotherapy: Preliminary Results

Directory of Open Access Journals (Sweden)

R. Laurent

2010-01-01

Full Text Available Organ motion leads to dosimetric uncertainties during a patient’s treatment. Much work has been done to quantify the dosimetric effects of lung movement during radiation treatment. There is a particular need for a good description and prediction of organ motion. To describe lung motion more precisely, we have examined the possibility of using a computer technique: a morphing algorithm. Morphing is an iterative method which consists of blending one image into another image. To evaluate the use of morphing, Four Dimensions Computed Tomography (4DCT acquisition of a patient was performed. The lungs were automatically segmented for different phases, and morphing was performed using the end-inspiration and the end-expiration phase scans only. Intermediate morphing files were compared with 4DCT intermediate images. The results showed good agreement between morphing images and 4DCT images: fewer than 2 % of the 512 by 256 voxels were wrongly classified as belonging/not belonging to a lung section. This paper presents preliminary results, and our morphing algorithm needs improvement. We can infer that morphing offers considerable advantages in terms of radiation protection of the patient during the diagnosis phase, handling of artifacts, definition of organ contours and description of organ motion.

Posterior perineal support as treatment for anal fissures--preliminary results with a new toilet seat device.

Science.gov (United States)

Tan, Kok-Yang; Seow-Choen, Francis; Hai, Chew Heng; Thye, Gan Kok

2009-03-01

Anal fissures can cause morbidity in an otherwise healthy young patient. The process of evacuation results in stretching and descent of the anoderm and perineum especially posteriorly. Posterior perineal support may provide counter pressure at the posterior aspect of the pelvic floor, balancing the pressure exerted by the faeces on the anal wall, thus improving evacuation and reducing the trauma associated with it, and reducing symptoms of anal fissures. Symptoms of constipation may also be reduced secondarily. We report the preliminary results with a novel, simple and noninvasive method of treatment provided by a toilet seat device. A prospective study was performed in 32 patients. The study was designed mainly to investigate the patients' subjective perceptions of their symptoms related to anal fissures and constipation. Questionnaires were provided to patients before, during and after treatment. The study revealed statistically significant improvement in pain, bleeding, symptoms of constipation and abdominal discomfort after 3 months usage of the device. The odds of patients perceiving an improvement in symptoms were also significantly increased after 3 months of treatment compared to 2 weeks of treatment. This preliminary study revealed that a posterior perineal support device can bring about significant improvement in the symptoms of patients with anal fissures. There may also be secondary benefits of a reduction in the symptoms of constipation. Although not conclusive, these results should serve as a springboard for further research into this area.

76 FR 62761 - Stainless Steel Bar From India: Extension of Time Limit for the Preliminary Results of the 2010...

Science.gov (United States)

2011-10-11

... DEPARTMENT OF COMMERCE International Trade Administration [A-533-810] Stainless Steel Bar From India: Extension of Time Limit for the Preliminary Results of the 2010-2011 Antidumping Duty... review of the antidumping duty order on stainless steel bar from India, covering the period February 1...

Subclinical myocardial dysfunction by tissue Doppler echocardiography in primary antiphospholipid syndrome: Preliminary results

Directory of Open Access Journals (Sweden)

Tarcila Fontes de Lima Gomes Lucena

2018-01-01

Conclusion: The present study demonstrated subclinical myocardial dysfunction using TDI in asymptomatic PAPS patients. TDI is non-invasive and cost effective. Prospective studies including a large number of participants in order to confirm these preliminary data are needed.

Polarimetry at 1.3 mm using MILLIPOL - methods and preliminary results for Orion

International Nuclear Information System (INIS)

Barvainis, R.; Clemens, D.P.; Leach, R.

1988-01-01

This paper describes a polarimeter for use at wavelengths near 1 mm, designed to be self-contained and portable. Only minor modifications should be required to adapt this instrument for use on any of several millimeter and submillimeter telescopes. The polarimeter system and data-taking techniques are described, and a preliminary measurement is reported of the polarized dust emission from the Orion KL region at 1.3 mm using the NRAO 12 m telescope. The results are similar to previous polarization measurements of Orion at far-infrared and submillimeter wavelengths. The magnetic field direction implied by the polarization position angle is parallel to that found in the surrounding Orion region using optical and near- to midinfrared polarimetric techniques. 17 references

Fusing Simulation Results From Multifidelity Aero-servo-elastic Simulators - Application To Extreme Loads On Wind Turbine

DEFF Research Database (Denmark)

Abdallah, Imad; Sudret, Bruno; Lataniotis, Christos

2015-01-01

Fusing predictions from multiple simulators in the early stages of the conceptual design of a wind turbine results in reduction in model uncertainty and risk mitigation. Aero-servo-elastic is a term that refers to the coupling of wind inflow, aerodynamics, structural dynamics and controls. Fusing...... the response data from multiple aero-servo-elastic simulators could provide better predictive ability than using any single simulator. The co-Kriging approach to fuse information from multifidelity aero-servo-elastic simulators is presented. We illustrate the co-Kriging approach to fuse the extreme flapwise...... bending moment at the blade root of a large wind turbine as a function of wind speed, turbulence and shear exponent in the presence of model uncertainty and non-stationary noise in the output. The extreme responses are obtained by two widely accepted numerical aero-servo-elastic simulators, FAST...

Preliminary PCA/TT Results on MRO CRISM Multispectral Images

Science.gov (United States)

Klassen, David R.; Smith, M. D.

2010-10-01

Mars Reconnaissance Orbiter arrived at Mars in March 2006 and by September had achieved its science-phase orbit with the Compact Reconnaissance Imaging Spectrometer for Mars (CRISM) beginning its visible to near-infrared (VIS/NIR) spectral imaging shortly thereafter. One goal of CRISM is to fill in the spatial gaps between the various targeted observations, eventually mapping the entire surface. Due to the large volume of data this would create, the instrument works in a reduced spectral sampling mode creating "multispectral” images. From these data we can create image cubes using 64 wavelengths from 0.410 to 3.923 µm. We present here our analysis of these multispectral mode data products using Principal Components Analysis (PCA) and Target Transformation (TT) [1]. Previous work with ground-based images [2-5] has shown that over an entire visible hemisphere, there are only three to four meaningful components using 32-105 wavelengths over 1.5-4.1 µm the first two are consistent over all temporal scales. The TT retrieved spectral endmembers show nearly the same level of consistency [5]. The preliminary work on the CRISM images cubes implies similar results; three to four significant principal components that are fairly consistent over time. These components are then used in TT to find spectral endmembers which can be used to characterize the surface reflectance for future use in radiative transfer cloud optical depth retrievals. We present here the PCA/TT results comparing the principal components and recovered endmembers from six reconstructed CRISM multi-spectral image cubes. References: [1] Bandfield, J. L., et al. (2000) JGR, 105, 9573. [2] Klassen, D. R. and Bell III, J. F. (2001) BAAS 33, 1069. [3] Klassen, D. R. and Bell III, J. F. (2003) BAAS, 35, 936. [4] Klassen, D. R., Wark, T. J., Cugliotta, C. G. (2005) BAAS, 37, 693. [5] Klassen, D. R. (2009) Icarus, 204, 32.

Development of a Closed Loop Simulator for Poloidal Field Control in DIII-D

International Nuclear Information System (INIS)

J.A. Leuer; M.L. Walker; D.A. Humphreys; J.R. Ferron; A. Nerem; B.G. Penaflor

1999-01-01

The design of a model-based simulator of the DIII-D poloidal field system is presented. The simulator is automatically configured to match a particular DIII-D discharge circuit. The simulator can be run in a data input mode, in which prior acquired DIII-D shot data is input to the simulator, or in a stand-alone predictive mode, in which the model operates in closed loop with the plasma control system. The simulator is used to design and validate a multi-input-multi-output controller which has been implemented on DIII-D to control plasma shape. Preliminary experimental controller results are presented

Correlating element atmospheric deposition and cancer mortality in Portugal: Data handling and preliminary results

International Nuclear Information System (INIS)

Sarmento, S.; Wolterbeek, H.Th.; Verburg, T.G.; Freitas, M.C.

2008-01-01

This study, framed within geographical epidemiology, presents preliminary findings concerning the association between the concentrations of chemical elements obtained through atmospheric biomonitoring with lichens and cancer mortality in the Portuguese population. Exploratory analyses were performed to identify potential confounders for the relationships between chemical elements and neoplasm mortality and to assess the extent of their interference. The results of this study highlight some methodological and conceptual difficulties inherent to observational and geographical studies, in the specific context of the Portuguese population, and the challenge posed by the large numbers of pollutants considered. - Relationship between chemical elements and mortality from neoplasms in the Portuguese population and the effect of confounders

Natural Gamma Emitters after a Selective Chemical Separation of a TENORM residue: Preliminary Results

International Nuclear Information System (INIS)

Alves de Freitas, Antonio; Abrao, Alcidio; Godoy dos Santos, Adir Janete; Pecequilo, Brigitte Roxana Soreanu

2008-01-01

An analytical procedure was established in order to obtain selective fractions containing radium isotopes ( 228 Ra), thorium ( 232 Th), and rare earths from RETOTER (REsiduo de TOrio e TErras Raras), a solid residue rich in rare earth elements, thorium isotopes and small amount of natural uranium generated from the operation of a thorium pilot plant for purification and production of pure thorium nitrate at IPEN -CNEN/SP. The paper presents preliminary results of 228 Ra, 226 Ra, 238 U, 210 Pb, and 40 K concentrations in the selective fractions and total residue determined by high-resolution gamma spectroscopy, considering radioactive equilibrium of the samples

Virtual simulation of maneuvering captive tests for a surface vessel

Directory of Open Access Journals (Sweden)

Ahmad Hajivand

2015-09-01

Full Text Available Hydrodynamic derivatives or coefficients are required to predict the maneuvering characteristics of a marine vehicle. These derivatives are obtained numerically for a DTMB 5512 model ship by virtual simulating of captive model tests in a CFD environment. The computed coefficients are applied to predict the turning circle and zigzag maneuvers of the model ship. The comparison of the simulated results with the available experimental data shows a very good agreement among them. The simulations show that the CFD is precise and affordable tool at the preliminary design stage to obtain maneuverability performance of a marine vehicles.

Porous titanium obtained by a new powder metallurgy technique: Preliminary results of human osteoblast adhesion on surface polished substrates.

Science.gov (United States)

Biasotto, M; Ricceri, R; Scuor, N; Schmid, C; Sandrucci, M A; Di Lenarda, R; Matteazzi, P

2003-01-01

This study concerns a novel powder metallurgy method for producing porous titanium (pTi) exhibiting high mechanical properties. The preparation procedure consisted of the following stages: first, the preparation of Ti and titanium hydride (TiH2) powder mixtures and their consolidation with a cold isostatic press, followed by a sintering of the green bodies performed with hot isostatic press (HIP) equipment. Thermal decomposition in controlled environment of the TiH2 phase results in the foam structure. The resulting porosity percolates with a volume fraction of approximately 20%. The final material exhibits interesting mechanical properties, comparable to those of full density titanium (between grade 2 and grade 3), with the advantage of a minor density. The samples produced were tested to verify their biological response by studying the effectiveness of osteoblast adhesion and growth. In this preliminary study, osteoblastic cell morphology was investigated and compared to that observed on fully dense commercially pure titanium (Ti-cp) (ASTM, grade 3). The preliminary results were promising regarding cellular adhesion and spreading. (Journal of Applied Biomaterials & Biomechanics 2003; 1: 172-7).

Extremity exposure in nuclear medicine: Preliminary results of a European study

International Nuclear Information System (INIS)

Merce, M. S.; Ruiz, N.; Barth, I.; Carnicer, A.; Donadille, L.; Ferrari, P.; Fulop, M.; Ginjaume, M.; Gualdrini, G.; Krim, S.; Mariotti, F.; Ortega, X.; Rimpler, A.; Vanhavere, F.; Baechler, S.

2011-01-01

The Work Package 4 of the ORAMED project, a collaborative project (2008-11) supported by the European Commission within its seventh Framework Programme, is concerned with the optimisation of the extremity dosimetry of medical staff in nuclear medicine. To evaluate the extremity doses and dose distributions across the hands of medical staff working in nuclear medicine departments, an extensive measurement programme has been started in 32 nuclear medicine departments in Europe. This was done using a standard protocol recording all relevant information for radiation exposure, i.e. radiation protection devices and tools. This study shows the preliminary results obtained for this measurement campaign. For diagnostic purposes, the two most-used radionuclides were considered: 99m Tc) and 18 F. For therapeutic treatments, Zevalin R and DOTATOC (both labelled with 90 Y) were chosen. Large variations of doses were observed across the hands depending on different parameters. Furthermore, this study highlights the importance of the positioning of the extremity dosemeter for a correct estimate of the maximum skin doses. (authors)

High dose rate brachytherapy (HDRB) in prostate cancer - technique description and preliminary results

International Nuclear Information System (INIS)

Cordova Junior, Ardo Lotar; Salvajoli, Joao Victor; Pelizzon, Antonio CAssio Assis; Cecilio, Paulo Jose

1998-01-01

Describe the technique and preliminary results of high dose rate brachytherapy (HDRB) in localized prostate cancer. Subjects methods: Between March, 1997 and April, 1998, 26 patients were treated with external beam radiotherapy (45 to 50.4 Gy - 1.8 Gy per day) and implants (16 Gy in 2 days - twice a day). Median age was 68 years. The distribution by clinical stage was: 5 T1c, 9 T2a, 10 T2b and 2 T3a. Median initial PSA was 16 ng/ml. Results: With a median follow-up of 4 months, 85% of patients showed normal levels of PSA, with a median of 0.6 ng/ml, 60 to 90 days after treatment. Dysuria grades 1 and 2 and proctitis grade 1 were found in 11,3 and 5 patients, respectively. Conclusion: The method is safe, with acceptable early side effects. Longer follow-up is necessary before drawing any conclusions. (author)

Preliminary test results from a free-piston Stirling engine technology demonstration program to support advanced radioisotope space power applications

International Nuclear Information System (INIS)

White, Maurice A.; Qiu Songgang; Augenblick, Jack E.

2000-01-01

Free-piston Stirling engines offer a relatively mature, proven, long-life technology that is well-suited for advanced, high-efficiency radioisotope space power systems. Contracts from DOE and NASA are being conducted by Stirling Technology Company (STC) for the purpose of demonstrating the Stirling technology in a configuration and power level that is representative of an eventual space power system. The long-term objective is to develop a power system with an efficiency exceeding 20% that can function with a high degree of reliability for up to 15 years on deep space missions. The current technology demonstration convertors (TDC's) are completing shakedown testing and have recently demonstrated performance levels that are virtually identical to projections made during the preliminary design phase. This paper describes preliminary test results for power output, efficiency, and vibration levels. These early results demonstrate the ability of the free-piston Stirling technology to exceed objectives by approximately quadrupling the efficiency of conventional radioisotope thermoelectric generators (RTG's)

Preliminary test results from a free-piston Stirling engine technology demonstration program to support advanced radioisotope space power applications

Science.gov (United States)

White, Maurice A.; Qiu, Songgang; Augenblick, Jack E.

2000-01-01

Free-piston Stirling engines offer a relatively mature, proven, long-life technology that is well-suited for advanced, high-efficiency radioisotope space power systems. Contracts from DOE and NASA are being conducted by Stirling Technology Company (STC) for the purpose of demonstrating the Stirling technology in a configuration and power level that is representative of an eventual space power system. The long-term objective is to develop a power system with an efficiency exceeding 20% that can function with a high degree of reliability for up to 15 years on deep space missions. The current technology demonstration convertors (TDC's) are completing shakedown testing and have recently demonstrated performance levels that are virtually identical to projections made during the preliminary design phase. This paper describes preliminary test results for power output, efficiency, and vibration levels. These early results demonstrate the ability of the free-piston Stirling technology to exceed objectives by approximately quadrupling the efficiency of conventional radioisotope thermoelectric generators (RTG's). .

Improved self-exclusion program: preliminary results.

Science.gov (United States)

Tremblay, Nicole; Boutin, Claude; Ladouceur, Robert

2008-12-01

The gambling industry has offered self-exclusion programs for quite a long time. Such measures are designed to limit access to gaming opportunities and provide problem gamblers with the help they need to cease or limit their gambling behaviour. However, few studies have empirically evaluated these programs. This study has three objectives: (1) to observe the participation in an improved self-exclusion program that includes an initial voluntary evaluation, phone support, and a mandatory meeting, (2) to evaluate satisfaction and usefulness of this service as perceived by self-excluders, (3) to measure the preliminary impact of this improved program. One hundred sixteen self-excluders completed a questionnaire about their satisfaction and their perception of the usefulness during the mandatory meeting. Among those participants, 39 attended an initial meeting. Comparisons between data collected at the initial meeting and data taken at the final meeting were made for those 39 participants. Data showed that gamblers chose the improved self-exclusion program 75% of the time; 25% preferred to sign a regular self-exclusion contract. Among those who chose the improved service, 40% wanted an initial voluntary evaluation and 37% of these individuals actually attended that meeting. Seventy percent of gamblers came to the mandatory meeting, which was a required condition to end their self-exclusion. The majority of participants were satisfied with the improved self-exclusion service and perceived it as useful. Major improvements were observed between the final and the initial evaluation on time and money spent, consequences of gambling, DSM-IV score, and psychological distress. The applicability of an improved self-exclusion program is discussed and, as shown in our study, the inclusion of a final mandatory meeting might not be so repulsive for self-excluders. Future research directives are also proposed.

An overview of CFD modelling of small-scale fixed-bed biomass pellet boilers with preliminary results from a simplified approach

International Nuclear Information System (INIS)

Chaney, Joel; Liu Hao; Li Jinxing

2012-01-01

Highlights: ► Overview of the overall approach of modelling fixed-bed biomass boilers in CFD. ► Bed sub-models of moisture evaporation, devolatisation and char combustion reviewed. ► A method of embedding a combustion model in discrete fuel zones within the CFD is suggested. ► Includes sample of preliminary results for a 50 kW pellet boiler. ► Clear physical trends predicted. - Abstract: The increasing global energy demand and mounting pressures for CO 2 mitigation call for increased efficient utilization of biomass, particularly for heating domestic and commercial buildings. The authors of the present paper are investigating the optimization of the combustion performance and NO x emissions of a 50 kW biomass pellet boiler fabricated by a UK manufacturer. The boiler has a number of adjustable parameters including the ratio of air flow split between the primary and secondary supplies, the orientation, height, direction and number of the secondary inlets. The optimization of these parameters provides opportunities to improve both the combustion efficiency and NO x emissions. When used carefully in conjunction with experiments, Computational Fluid Dynamics (CFD) modelling is a useful tool for rapidly and at minimum cost examining the combustion performance and emissions from a boiler with multiple variable parameters. However, modelling combustion and emissions of a small-scale biomass pellet boiler is not trivial and appropriate fixed-bed models that can be coupled with the CFD code are required. This paper reviews previous approaches specifically relevant to simulating fixed-bed biomass boilers. In the first part it considers approaches to modelling the heterogeneous solid phase and coupling this with the gas phase. The essential components of the sub-models are then overviewed. Importantly, for the optimization process a model is required that has a good balance between accuracy in predicting physical trends, with low computational run time. Finally, a

Ocean surface waves and winds over the north Indian Ocean from satellite altimeter - preliminary results of SAC-NIO joint project

Digital Repository Service at National Institute of Oceanography (India)

Sarkar, A.; Rajkumar, R.; Gairola, R.M.; Gohil, B.S.; Vethamony, P.; Rao, L.V.G.

the respective correlation coefficients. Preliminary results with limited processed data showed that the correlation coefficients are approximately 0.6. Sample maps of wave and wind (satellite derived) in 2.5 degrees x 2.5 degrees grids have been prepared...

[Simulation-based intervention to improve anesthesiology residents communication with families of critically ill patients--preliminary prospective evaluation].

Science.gov (United States)

Berkenstadt, Haim; Perlson, Daria; Shalomson, Orit; Tuval, Atalia; Haviv-Yadid, Yael; Ziv, Amitai

2013-08-01

Although effective communication with families of critically ill patients is a vital component of quality care, training in this field is neglected. The article aims to validate communication skills training program for anesthesiology residents in the intensive care set up. Ten anesthesia residents, following 3 months of Intensive Care Unit (ICU) rotation, had 4 hours of lectures and one day simulation-based communication skills training with families of critically ill patients. Participants completed an attitude questionnaire over 3 time periods--before training [t1], immediately following training (t2) and three months following training (t3). The participants' communication skills were assessed by two blinded independent observers using the SEGUE framework while performing a simulation-based scenario at t1 and t3. Seven participants finished the study protocol. Participants ndicated communication importance as 3.68 +/- 0.58 (t1), 4.05 +/- 0.59 (t2), 4.13 +/- 0.64 (t3); their communication ability as 3.09 +/- 0.90 (t1), 3.70 +/- 0.80 (t2), 3.57 +/- 0.64 (t3); the contribution of lecture to communication 3.04 +/- 0.43 (t1), 3.83 +/- 0.39 (t2), 3.87 +/- 0.51 (t3), and contribution of simulation training to communication 3.00 +/- 0.71 (t1), 4.04 +/- 0.52 (t2), 3.84 +/- 0.31 (t3). The differences did not reach statistical significance. Objective assessment of the communication skills using the SEGUE framework indicated that 6/7 participants improved their communication skills, with communication ability before training at 2.66 +/- 0.83 and 1 month following training it was 3.38 +/- 0.78 (p = 0.09). This preliminary study demonstrates the value of communication skills training in the intensive care environment.

ANOVA parameters influence in LCF experimental data and simulation results

Directory of Open Access Journals (Sweden)

Vercelli A.

2010-06-01

Full Text Available The virtual design of components undergoing thermo mechanical fatigue (TMF and plastic strains is usually run in many phases. The numerical finite element method gives a useful instrument which becomes increasingly effective as the geometrical and numerical modelling gets more accurate. The constitutive model definition plays an important role in the effectiveness of the numerical simulation [1, 2] as, for example, shown in Figure 1. In this picture it is shown how a good cyclic plasticity constitutive model can simulate a cyclic load experiment. The component life estimation is the subsequent phase and it needs complex damage and life estimation models [3-5] which take into account of several parameters and phenomena contributing to damage and life duration. The calibration of these constitutive and damage models requires an accurate testing activity. In the present paper the main topic of the research activity is to investigate whether the parameters, which result to be influent in the experimental activity, influence the numerical simulations, thus defining the effectiveness of the models in taking into account of all the phenomena actually influencing the life of the component. To obtain this aim a procedure to tune the parameters needed to estimate the life of mechanical components undergoing TMF and plastic strains is presented for commercial steel. This procedure aims to be easy and to allow calibrating both material constitutive model (for the numerical structural simulation and the damage and life model (for life assessment. The procedure has been applied to specimens. The experimental activity has been developed on three sets of tests run at several temperatures: static tests, high cycle fatigue (HCF tests, low cycle fatigue (LCF tests. The numerical structural FEM simulations have been run on a commercial non linear solver, ABAQUS®6.8. The simulations replied the experimental tests. The stress, strain, thermal results from the thermo

EXPLOSION POTENTIAL ASSESSMENT OF HEAT EXCHANGER NETWORK AT THE PRELIMINARY DESIGN STAGE

Directory of Open Access Journals (Sweden)

MOHSIN PASHA

2016-07-01

Full Text Available The failure of Shell and Tube Heat Exchangers (STHE is being extensively observed in the chemical process industries. This failure can cause enormous production loss and have a potential of dangerous consequences such as an explosion, fire and toxic release scenarios. There is an urgent need for assessing the explosion potential of shell and tube heat exchanger at the preliminary design stage. In current work, inherent safety index based approach is used to resolve the highlighted issue. Inherent Safety Index for Shell and Tube Heat Exchanger (ISISTHE is a newly developed index for assessing the inherent safety level of a STHE at the preliminary design stage. This index is composed of preliminary design variables and integrated with the process design simulator (Aspen HYSYS. Process information can easily be transferred from process design simulator to MS Excel spreadsheet owing to this integration. This index could potentially facilitate the design engineer to analyse the worst heat exchanger in the heat exchanger network. Typical heat exchanger network of the steam reforming process is presented as a case study and the worst heat exchanger of this network has been identified. It is inferred from this analysis that shell and tube heat exchangers possess high operating pressure, corrected mean temperature difference (CMTD and flammability and reactive potential needs to be critically analysed at the preliminary design stage.

A preliminary assessment of polymer-modified cements for use in immobilisation of intermediate level radioactive waste

International Nuclear Information System (INIS)

Burnay, S.G.; Dyson, J.R.

1982-11-01

A range of polymer-modified cements has been examined as candidate materials for the immobilisation of intermediate level radioactive waste. The waste streams studied were inactive simulates of real wastes and included ion-exchange resins, Magnox debris and dilute sludges. Preliminary experiments on the compatibility of the polymer-cement-waste combinations have been carried out and measurements of flexural strength before and after #betta#-irradiation to 10 9 rad and water immersion have been made. Soxhlet leach tests have been used to compare the leach rates of the different materials. From the results of these preliminary experiments, a limited number of polymer-modified cements have been suggested as suitable for more detailed study. (author)

Preliminary systems-interaction results from the Digraph Matrix Analysis of the Watts Bar Nuclear Power Plant safety-injection systems

International Nuclear Information System (INIS)

Sacks, I.J.; Ashmore, B.C.; Champney, J.M.; Alesso, H.P.

1983-06-01

This report provides preliminary results generated by a Digraph Matrix Analysis (DMA) for a Systems Interaction analysis performed on the Safety Injection System of the Tennessee Valley Authority Watts Bar Nuclear Power Plant. An overview of DMA is provided along with a brief description of the computer codes used in DMA

Preliminary simulation studies of accelerator cavity loading

International Nuclear Information System (INIS)

Faehl, R.J.

1980-06-01

Two-dimensional simulations of loading effects in a 350 MHz accelerator cavity have been performed. Electron currents of 1-10 kA have been accelerated in 5 MV/m fields. Higher order cavity modes induced by the beam may lead to emittance growth. Operation in an autoaccelerator mode has been studied

Preliminary results from Brookhaven Experiment 802 with 14.5 GeVu 28Si

International Nuclear Information System (INIS)

1987-01-01

Preliminary data on beam calorimetry, charged particle multiplicities, pseudo-rapidity distributions and hadron spectroscopy from 28 Si + Al and Au at 14.5 GeV per nucleon are presented. Comments on nuclear stopping, multiplicity systematics, and Kπ ratios are offered. 5 refs., 6 figs., 1 tab

Religious versus Conventional Psychotherapy for Major Depression in Patients with Chronic Medical Illness: Rationale, Methods, and Preliminary Results

Directory of Open Access Journals (Sweden)

Harold G. Koenig

2012-01-01

Full Text Available This paper (1 reviews the physical and religious barriers to CBT that disabled medically ill-depressed patients face, (2 discusses research on the relationship between religion and depression-induced physiological changes, (3 describes an ongoing randomized clinical trial of religious versus secular CBT in chronically ill patients with mild-to-moderate major depression designed to (a overcome physical and religious barriers to CBT and (b compare the efficacy of religious versus secular CBT in relieving depression and improving immune and endocrine functions, and (4 presents preliminary results that illustrate the technical difficulties that have been encountered in implementing this trial. CBT is being delivered remotely via instant messaging, telephone, or Skype, and Christian, Jewish, Muslim, Buddhist, and Hindu versions of religious CBT are being developed. The preliminary results described here are particular to the technologies employed in this study and are not results from the CBT clinical trial whose findings will be published in the future after the study ends and data are analyzed. The ultimate goal is to determine if a psychotherapy delivered remotely that integrates patients’ religious resources improves depression more quickly than a therapy that ignores them, and whether religious CBT is more effective than conventional CBT in reversing depression-induced physiological changes.

Direct numerical simulation of annular flows

Science.gov (United States)

Batchvarov, Assen; Kahouadji, Lyes; Chergui, Jalel; Juric, Damir; Shin, Seungwon; Craster, Richard V.; Matar, Omar K.

2017-11-01

Vertical counter-current two-phase flows are investigated using direct numerical simulations. The computations are carried out using Blue, a front-tracking-based CFD solver. Preliminary results show good qualitative agreement with experimental observations in terms of interfacial phenomena; these include three-dimensional, large-amplitude wave formation, the development of long ligaments, and droplet entrainment. The flooding phenomena in these counter current systems are closely investigated. The onset of flooding in our simulations is compared to existing empirical correlations such as Kutateladze-type and Wallis-type. The effect of varying tube diameter and fluid properties on the flooding phenomena is also investigated in this work. EPSRC, UK, MEMPHIS program Grant (EP/K003976/1), RAEng Research Chair (OKM).

Biological image construction by using Raman radiation and Pca: preliminary results

International Nuclear Information System (INIS)

Martinez E, J. C.; Cordova F, T.; Hugo R, V.

2015-10-01

Full text: In the last years, the Raman spectroscopy (Rs) technique has had some applications in the study and analysis of biological samples, due to it is able to detect concentrations or presence of certain organic and inorganic compounds of medical interest. In this work, raw data were obtained through measurements in selected points on a square regions in order to detect specific organic / inorganic compounds on biological samples. Gold nano stars samples were prepared and coated with membrane markers (CD 10+ and CD 19+) and diluted in leukemic B lymphocytes. Each data block was evaluated independently by the method of principal component analysis (Pca) in order to find representative dimensionless values (Cp) for each Raman spectrum in a specific coordinate. Each Cp was normalized in a range of 0-255 in order to generate a representative image of 8 bits of the region under study. Data acquisition was performed with Raman microscopy system Renishaw in Via in the range of 550 to 1700 cm-1 with a 785 nm laser source, with a power of 17 m W and 15 s of exposure time were used for each spectrum. In preliminary results could detect the presence of molecular markers CD 10+ and CD 19+ with gold nano stars and discrimination between both markers. The results suggest conducting studies with specific concentrations organic and inorganic materials. (Author)

Biological image construction by using Raman radiation and Pca: preliminary results

Energy Technology Data Exchange (ETDEWEB)

Martinez E, J. C. [IPN, Unidad Profesional Interdisciplinaria de Ingenieria, Campus Guanajuato, Av. Mineral de Valenciana 200, Col. Fracc. Industrial Puerto Interior, 36275 Silao, Guanajuato (Mexico); Cordova F, T. [Universidad de Guanajuato, DIC, Departamento de Ingenieria Fisica, Loma del Bosque No. 103, Col. Lomas del Campestre, 37150 Leon, Guanajuato (Mexico); Hugo R, V., E-mail: jcmartineze@ipn.mx [Universidad de Guadalajara, Centro Universitario de Tonala, Morelos No. 180, 69584 Tonala, Jalisco (Mexico)

2015-10-15

Full text: In the last years, the Raman spectroscopy (Rs) technique has had some applications in the study and analysis of biological samples, due to it is able to detect concentrations or presence of certain organic and inorganic compounds of medical interest. In this work, raw data were obtained through measurements in selected points on a square regions in order to detect specific organic / inorganic compounds on biological samples. Gold nano stars samples were prepared and coated with membrane markers (CD 10+ and CD 19+) and diluted in leukemic B lymphocytes. Each data block was evaluated independently by the method of principal component analysis (Pca) in order to find representative dimensionless values (Cp) for each Raman spectrum in a specific coordinate. Each Cp was normalized in a range of 0-255 in order to generate a representative image of 8 bits of the region under study. Data acquisition was performed with Raman microscopy system Renishaw in Via in the range of 550 to 1700 cm-1 with a 785 nm laser source, with a power of 17 m W and 15 s of exposure time were used for each spectrum. In preliminary results could detect the presence of molecular markers CD 10+ and CD 19+ with gold nano stars and discrimination between both markers. The results suggest conducting studies with specific concentrations organic and inorganic materials. (Author)

Preliminary Simulation of the Corrosion Rate of Archaeological Glass

Energy Technology Data Exchange (ETDEWEB)

Steefel, Carl

2014-01-06

In this study, we make use of a micro-continuum modeling approach (the Kinetic-Microscopic-Continuum Model or K{micro}C model) to capture the spatial distribution and identity of reaction products developing over time as a result of the archaeological glass corrosion, while also matching the time scales of alteration where possible. Since the glass blocks sat on the Mediterranean seafloor for 1800 years, the physical and chemical boundary conditions are largely constant. We focus on a fracture within the glass block identified by Verney-Carron et al. (2008) and simulate it as a 1D system, with a fixed concentration (Dirichlet) boundary corresponding to the interior of the fracture.

A method for data handling numerical results in parallel OpenFOAM simulations

International Nuclear Information System (INIS)

nd Vasile Pârvan Ave., 300223, TM Timişoara, Romania, alin.anton@cs.upt.ro (Romania))" data-affiliation=" (Faculty of Automatic Control and Computing, Politehnica University of Timişoara, 2nd Vasile Pârvan Ave., 300223, TM Timişoara, Romania, alin.anton@cs.upt.ro (Romania))" >Anton, Alin; th Mihai Viteazu Ave., 300221, TM Timişoara (Romania))" data-affiliation=" (Center for Advanced Research in Engineering Science, Romanian Academy – Timişoara Branch, 24th Mihai Viteazu Ave., 300221, TM Timişoara (Romania))" >Muntean, Sebastian

2015-01-01

Parallel computational fluid dynamics simulations produce vast amount of numerical result data. This paper introduces a method for reducing the size of the data by replaying the interprocessor traffic. The results are recovered only in certain regions of interest configured by the user. A known test case is used for several mesh partitioning scenarios using the OpenFOAM toolkit ® [1]. The space savings obtained with classic algorithms remain constant for more than 60 Gb of floating point data. Our method is most efficient on large simulation meshes and is much better suited for compressing large scale simulation results than the regular algorithms

A method for data handling numerical results in parallel OpenFOAM simulations

Energy Technology Data Exchange (ETDEWEB)

Anton, Alin [Faculty of Automatic Control and Computing, Politehnica University of Timişoara, 2" n" d Vasile Pârvan Ave., 300223, TM Timişoara, Romania, alin.anton@cs.upt.ro (Romania); Muntean, Sebastian [Center for Advanced Research in Engineering Science, Romanian Academy – Timişoara Branch, 24" t" h Mihai Viteazu Ave., 300221, TM Timişoara (Romania)

2015-12-31

Parallel computational fluid dynamics simulations produce vast amount of numerical result data. This paper introduces a method for reducing the size of the data by replaying the interprocessor traffic. The results are recovered only in certain regions of interest configured by the user. A known test case is used for several mesh partitioning scenarios using the OpenFOAM toolkit{sup ®}[1]. The space savings obtained with classic algorithms remain constant for more than 60 Gb of floating point data. Our method is most efficient on large simulation meshes and is much better suited for compressing large scale simulation results than the regular algorithms.

Gonioscopy-assisted transluminal trabeculotomy, ab interno trabeculotomy: technique report and preliminary results.

Science.gov (United States)

Grover, Davinder S; Godfrey, David G; Smith, Oluwatosin; Feuer, William J; Montes de Oca, Ildamaris; Fellman, Ronald L

2014-04-01

To introduce a minimally invasive, ab interno approach to a circumferential 360-degree trabeculotomy and to report the preliminary results. Retrospective, noncomparative cases series. Eighty-five eyes of 85 consecutive patients who sought treatment at Glaucoma Associates of Texas with uncontrolled open-angle glaucoma and underwent gonioscopy-assisted transluminal trabeculotomy (GATT) for whom there was at least 6 months of follow-up data. Retrospective chart review of patients who underwent GATT by 4 of the authors (D.S.G., D.G.G., O.S., R.L.F.) between October 2011 and October 2012. The surgery was performed in adults with various open-angle glaucomas. Intraocular pressure (IOP), glaucoma medications, visual acuity, and intraoperative as well as postoperative complications. Eighty-five patients with an age range of 24 to 88 years underwent GATT with at least 6 months of follow-up. In 57 patients with primary open-angle glaucoma, the IOP decreased by 7.7 mmHg (standard deviation [SD], 6.2 mm Hg; 30.0% [SD, 22.7%]) with an average decrease in glaucoma medications of 0.9 (SD, 1.3) at 6 months. In this group, the IOP decreased by 11.1 mmHg (SD, 6.1 mmHg; 39.8% [SD, 16.0%]) with 1.1 fewer glaucoma medications at 12 months. In the secondary glaucoma group of 28 patients, IOP decreased by 17.2 mmHg (SD, 10.8 mmHg; 52.7% [SD, 15.8%]) with an average of 2.2 fewer glaucoma medications at 6 months. In this group, the IOP decreased by 19.9 mmHg (SD, 10.2 mmHg; 56.8% [SD, 17.4%]) with an average of 1.9 fewer medications (SD, 2.1) at 12 months. Treatment was considered to have failed in 9% (8/85) of patients because of the need for further glaucoma surgery. The cumulative proportion of failure at 1 year ranged from 0.1 to 0.32, depending on the group. Lens status or concurrent cataract surgery did not have a statistically significant effect on IOP in eyes that underwent GATT at either 6 or 12 months (P > 0.35). The most common complication was transient hyphema, seen in

Design aspects of the Alpha Repository. I. Preliminary results of facility layout, room stability, and equipment selection efforts. Summary progress report RSI-0024

International Nuclear Information System (INIS)

Gnirk, P.F.; Grams, W.H.; Zeller, T.J.; Ellis, D.B.; Pariseau, W.G.; Fossum, A.F.; Ratigan, J.L.; Hansen, F.D.

1975-01-01

Results of preliminary analysis of the stability of mines in salt formations underlying Eddy and Lea Counties in New Mexico are presented. Methods and equipment for drilling canister emplacement holes in these formations were evaluated along with methods for excavating storage areas and transport of the excavated salt. Progress during the period is reported in chapters on geological and rock properties at the repository site, preliminary mine layout, basic requirements for repository usage, excavation geometries, drill selection, excavation systems, and safety requirements

Preliminary result on trabecular bone score (TBS in lumbar vertebrae with experimentally altered microarchitecture

Directory of Open Access Journals (Sweden)

M. Di Stefano

2013-01-01

Full Text Available The aim of this preliminary research is to investigate the reliability of a new qualitative parameter, called Trabecular Bone Score (TBS, recently proposed for evaluating the microarchitectural arrangement of cancellous bone in scans carried out by dual energy X-ray absorptiometry (DXA. Vertebral bodies of 15 fresh samples of lumbar spines of adult pig were analysed either in basal conditions and with altered microarchitecture of the cancellous bone obtained by progressive drilling. The examined bony areas do not show changes in bone mineral density (BMD, whereas TBS values decrease with the increasing alteration of the vertebral microtrabecular structure. Our preliminary data seem to confirm the reliability of TBS as a qualitative parameter useful for evaluating the microarchitectural strength in bony areas quantitatively analysed by DXA.

Predictive validity of driving-simulator assessments following traumatic brain injury: a preliminary study.

Science.gov (United States)

Lew, Henry L; Poole, John H; Lee, Eun Ha; Jaffe, David L; Huang, Hsiu-Chen; Brodd, Edward

2005-03-01

To evaluate whether driving simulator and road test evaluations can predict long-term driving performance, we conducted a prospective study on 11 patients with moderate to severe traumatic brain injury. Sixteen healthy subjects were also tested to provide normative values on the simulator at baseline. At their initial evaluation (time-1), subjects' driving skills were measured during a 30-minute simulator trial using an automated 12-measure Simulator Performance Index (SPI), while a trained observer also rated their performance using a Driving Performance Inventory (DPI). In addition, patients were evaluated on the road by a certified driving evaluator. Ten months later (time-2), family members observed patients driving for at least 3 hours over 4 weeks and rated their driving performance using the DPI. At time-1, patients were significantly impaired on automated SPI measures of driving skill, including: speed and steering control, accidents, and vigilance to a divided-attention task. These simulator indices significantly predicted the following aspects of observed driving performance at time-2: handling of automobile controls, regulation of vehicle speed and direction, higher-order judgment and self-control, as well as a trend-level association with car accidents. Automated measures of simulator skill (SPI) were more sensitive and accurate than observational measures of simulator skill (DPI) in predicting actual driving performance. To our surprise, the road test results at time-1 showed no significant relation to driving performance at time-2. Simulator-based assessment of patients with brain injuries can provide ecologically valid measures that, in some cases, may be more sensitive than a traditional road test as predictors of long-term driving performance in the community.

Science-based HRA: experimental comparison of operator performance to IDAC (Information-Decision-Action Crew) simulations

Energy Technology Data Exchange (ETDEWEB)

Shirley, Rachel [The Ohio State Univ., Columbus, OH (United States); Smidts, Carol [The Ohio State Univ., Columbus, OH (United States); Boring, Ronald [Idaho National Lab. (INL), Idaho Falls, ID (United States); Li, Yuandan [Univ. of Maryland, College Park, MD (United States); Mosleh, Ali [Univ. of Maryland, College Park, MD (United States)

2015-02-01

Information-Decision-Action Crew (IDAC) operator model simulations of a Steam Generator Tube Rupture are compared to student operator performance in studies conducted in the Ohio State University’s Nuclear Power Plant Simulator Facility. This study is presented as a prototype for conducting simulator studies to validate key aspects of Human Reliability Analysis (HRA) methods. Seven student operator crews are compared to simulation results for crews designed to demonstrate three different decision-making strategies. The IDAC model used in the simulations is modified slightly to capture novice behavior rather that expert operators. Operator actions and scenario pacing are compared. A preliminary review of available performance shaping factors (PSFs) is presented. After the scenario in the NPP Simulator Facility, student operators review a video of the scenario and evaluate six PSFs at pre-determined points in the scenario. This provides a dynamic record of the PSFs experienced by the OSU student operators. In this preliminary analysis, Time Constraint Load (TCL) calculated in the IDAC simulations is compared to TCL reported by student operators. We identify potential modifications to the IDAC model to develop an “IDAC Student Operator Model.” This analysis provides insights into how similar experiments could be conducted using expert operators to improve the fidelity of IDAC simulations.

Electron-cloud updated simulation results for the PSR, and recent results for the SNS

International Nuclear Information System (INIS)

Pivi, M.; Furman, M.A.

2002-01-01

Recent simulation results for the main features of the electron cloud in the storage ring of the Spallation Neutron Source (SNS) at Oak Ridge, and updated results for the Proton Storage Ring (PSR) at Los Alamos are presented in this paper. A refined model for the secondary emission process including the so called true secondary, rediffused and backscattered electrons has recently been included in the electron-cloud code

Experiment vs simulation RT WFNDEC 2014 benchmark: CIVA results

International Nuclear Information System (INIS)

Tisseur, D.; Costin, M.; Rattoni, B.; Vienne, C.; Vabre, A.; Cattiaux, G.; Sollier, T.

2015-01-01

The French Atomic Energy Commission and Alternative Energies (CEA) has developed for years the CIVA software dedicated to simulation of NDE techniques such as Radiographic Testing (RT). RT modelling is achieved in CIVA using combination of a determinist approach based on ray tracing for transmission beam simulation and a Monte Carlo model for the scattered beam computation. Furthermore, CIVA includes various detectors models, in particular common x-ray films and a photostimulable phosphor plates. This communication presents the results obtained with the configurations proposed in the World Federation of NDEC 2014 RT modelling benchmark with the RT models implemented in the CIVA software

Experiment vs simulation RT WFNDEC 2014 benchmark: CIVA results

Energy Technology Data Exchange (ETDEWEB)

Tisseur, D., E-mail: david.tisseur@cea.fr; Costin, M., E-mail: david.tisseur@cea.fr; Rattoni, B., E-mail: david.tisseur@cea.fr; Vienne, C., E-mail: david.tisseur@cea.fr; Vabre, A., E-mail: david.tisseur@cea.fr; Cattiaux, G., E-mail: david.tisseur@cea.fr [CEA LIST, CEA Saclay 91191 Gif sur Yvette Cedex (France); Sollier, T. [Institut de Radioprotection et de Sûreté Nucléaire, B.P.17 92262 Fontenay-Aux-Roses (France)

2015-03-31

The French Atomic Energy Commission and Alternative Energies (CEA) has developed for years the CIVA software dedicated to simulation of NDE techniques such as Radiographic Testing (RT). RT modelling is achieved in CIVA using combination of a determinist approach based on ray tracing for transmission beam simulation and a Monte Carlo model for the scattered beam computation. Furthermore, CIVA includes various detectors models, in particular common x-ray films and a photostimulable phosphor plates. This communication presents the results obtained with the configurations proposed in the World Federation of NDEC 2014 RT modelling benchmark with the RT models implemented in the CIVA software.

A novel ultra-short scanning nuclear microprobe: Design and preliminary results

International Nuclear Information System (INIS)

Lebed, S.; Butz, T.; Vogt, J.; Reinert, T.; Spemann, D.; Heitmann, J.; Stachura, Z.; Lekki, J.; Potempa, A.; Styczen, J.; Sulkio-Cleff, B.

2001-01-01

The paper describes an optimized scanning nuclear microprobe (MP) with a new ultra-short (total length of 1.85 m) probe forming system based on a divided Russian quadruplet (DRQ) of magnetic quadrupole lenses. Modern electrostatic accelerators have a comparatively high beam brightness of about 10-25 pA/μm 2 /mrad 2 /MeV. This allows the MP proposed to provide a high lateral resolution even with large (1%) parasitic (sextupole and octupole) pole tip field components in all lenses. The features of the design permit the MP operation in the high current and low current modes with a short working distance and inexpensive quadrupole lenses. A new quadrupole doublet design has been developed for the MP. In the present work the calculated features of the new MP are compared with preliminary experimental results obtained with a similar system (total length of 2.3 m) at the INP in Cracow. The new MP is promising for studies of solids or biological samples with high resolutions (0.08-2 μm) in both modes under ambient conditions. A vertical version of the ultra-short MP can be very useful for single ion bombardments of living cells

Preliminary results of the International Fusion Materials Irradiation Facility deuteron injector

Energy Technology Data Exchange (ETDEWEB)

Gobin, R.; Adroit, G.; Bogard, D.; Bourdelle, G.; Chauvin, N.; Delferriere, O.; Gauthier, Y.; Girardot, P.; Guiho, P.; Harrault, F.; Jannin, J. L.; Loiseau, D.; Mattei, P.; Roger, A.; Sauce, Y.; Senee, F.; Vacher, T. [Commissariat a l' Energie Atomique et aux Energie Alternatives, CEA/Saclay, DSM/IRFU, 91191-Gif/Yvette (France)

2012-02-15

In the framework of the IFMIF-EVEDA project (International Fusion Materials Irradiation Facility-Engineering Validation and Engineering Design Activities), CEA/IRFU is in charge of the design, construction, and characterization of the 140 mA continuous deuteron injector, including the source and the low energy beam line. The electron cyclotron resonance ion source which operates at 2.45 GHz is associated with a 4-electrode extraction system in order to minimize beam divergence at the source exit. Krypton gas injection is foreseen in the 2-solenoid low energy beam line. Such Kr injection will allow reaching a high level of space charge compensation in order to improve the beam matching at the radio frequency quadrupole (RFQ) entrance. The injector construction is now completed on the Saclay site and the first plasma and beam production has been produced in May 2011. This installation will be tested with proton and deuteron beams either in pulsed or continuous mode at Saclay before shipping to Japan. In this paper, after a brief description of the installation, the preliminary results obtained with hydrogen gas injection into the plasma chamber will be reported.

Community Consultation and Public Disclosure: Preliminary Results From A New Model

Science.gov (United States)

Ramsey, Cornelia A.; Quearry, Bonnie; Ripley, Elizabeth

2011-01-01

Emergency medicine research conducted under the exception from informed consent (EFIC) regulation enables critical scientific advancements. When EFIC is proposed, there is a requirement for broad community consultation and public disclosure regarding the risks and benefits of the study. At the present time, no clear guidelines or standards exist for conducting and evaluating the community consultation and public disclosure. This preliminary study tested the feasibility and acceptability of a new approach to community consultation and public disclosure for a large-scale EFIC trial by engaging community members in designing and conducting the strategies. The authors enrolled key community members (called Community Advocates for Research, or CARs) to use community-based participatory methods to design and implement community consultation and public disclosure. By partnering with community members who represent target populations for the research study, this new approach has demonstrated a feasible community consultation and public disclosure plan with greater community participation and less cost than previous studies. In a community survey, the percentage of community members reporting having heard about the EFIC trial more than doubled after employing the new approach. This article discusses initial implementation and results. PMID:21729187

Test results with the Transrapid 06. System data from preliminary trials

Energy Technology Data Exchange (ETDEWEB)

Heinrich, K; Mnich, P

1987-10-01

Following the takeover of the Transrapid maglev facility by MVP, in spite of remaining preparatory work and conversion of the support and guidance system on the basis of a new electronic generation, interesting system data could be obtained experimentally before the planned continuous trials phase. Although the full test track length is not yet available - it is at present only 20.5 km - more than 25,000 km have already been covered in almost 1,200 test runs. Some 200 of these were for the purpose of demonstrating the Transrapid technology to visting German and foreign experts. The system data obtained from the preliminary trails were positive. Any weak points noted were mainly site-specific and not maglev-specific, but in spite of generally satisfactory results there are still many individual aspects calling for improvement and optimation before the technology can be declared ready for service. Proceeding from the positive trend of the system data obtained at up to 355 km/h, it can be said that proof of serviceability of the Transrapid transport system at speeds of up to 400 km/h can be provided in the next two years. (orig.).

Preliminary test results from the HSST shallow-crack fracture toughness program

International Nuclear Information System (INIS)

Theiss, T.J.; Robinson, G.C.; Rolfe, S.T.

1991-01-01

The Heavy Section Steel Technology (HSST) Program under sponsorship of the Nuclear Regulatory Commission (NRC) is investigating the influence of crack depth on the fracture toughness of reactor pressure vessel steel. The ultimate goal of the investigation is the generation of a limited data base of elastic-plastic fracture toughness values appropriate for shallow flaws in a reactor pressure vessel and the application of this data to reactor vessel life assessments. It has been shown that shallow-flaws play a dominant role in the probabilistic fracture mechanics analysis of reactor pressure vessels during a pressurized-thermal-shock event. In addition, recent research has shown that the crack initiation toughness measured using specimens with shallow flaws is greater that the toughness determined with conventional, deeply notched specimens at temperatures within the transition region for non-nuclear steels. The influence of crack depth on the elastic-plastic fracture toughness for prototypic reactor material is being investigated. Preliminary results indicate a significant increase in the toughness associated with shallow-flaws which has the potential to significantly impact the conditional probability of vessel failure. 8 refs., 4 figs., 1 tab

Radiolabeled antifibrin antibody in the detection of venous thrombosis: Preliminary results

International Nuclear Information System (INIS)

Alavi, A.; Palevsky, H.I.; Gupta, N.; Meranze, S.; Kelley, M.A.; Jatlow, A.D.; Schaible, T.F.; Brown, J.; Berger, H.J.

1990-01-01

The recent development of monoclonal antibodies against components of coagulated blood may provide new approaches to the diagnosis of venous thrombosis. Scanning with an indium-111-labeled Fab fragment of a murine monoclonal antifibrin antibody (59D8) and ascending contrast venography were performed in 33 patients. Images of the calves, popliteal fossae, thighs, and pelvis were obtained immediately, 4-6 hours, and 24 hours after injection of 2 mCi (74 MBq) of the antibody. All images were read in a blinded manner. Findings in both studies were positive in 28 patients and negative in three. In 19 patients not undergoing heparin therapy, 19 specific anatomic sites were positive on venograms and 29 were positive on antibody images (19 sites matched). In 14 patients undergoing heparin therapy, 34 sites were positive on venograms and 27 were positive on antibody images (22 sites matched). In most patients, positive results were noted within 1 hour of antibody injection. No adverse effects were noted with the antibody preparation. Preliminary data suggest that antifibrin antibody imaging is sensitive in detecting clots, is safe to use, and may have a role in diagnosing and managing venous thrombosis

A new confined high pressure rotary shear apparatus: preliminary results

Science.gov (United States)

Faulkner, D.; Coughlan, G.; Bedford, J. D.

2017-12-01

The frictional properties of fault zone materials, and their evolution during slip, are of paramount importance for determining the earthquake mechanics of large tectonic faults. Friction is a parameter that is difficult to determine from seismological methods so much of our understanding comes from experiment. Rotary shear apparatuses have been widely used in experimental studies to elucidate the frictional properties of faults under realistic earthquake slip velocities (0.1-10 m/s) and displacements (>20 m). However one technical limitation of rotary shear experiments at seismic slip rates has been the lack of confinement. This has led to a limit on the normal stress (due to the strength of the forcing blocks) and also a lack of control of measurements of the pore fluid pressure. Here we present the first preliminary results from a rotary shear apparatus that has been developed to attempt to address this issue. The new fully confined ring shear apparatus has a fast-acting servo-hydraulic confining pressure system of up to 200 MPa and a servo-controlled upstream and downstream pore pressure system of up to 200 MPa. Displacement rates of 0.01μ/s to 2 m/s can be achieved. Fault gouge samples can therefore be sheared at earthquake speed whilst being subject to pressures typically associated with the depth of earthquake nucleation.

Preliminary evaluation of a virtual reality-based simulator for learning spinal anesthesia.

LENUS (Irish Health Repository)

2012-12-27

STUDY OBJECTIVE: To evaluate the influence of a simulation-based program on the initial performance of dural puncture by medical interns, and to refine the design of simulator-based teaching and competence assessment. DESIGN: Prospective interventional study. SETTING: Academic medical center. SUBJECTS: 27 medical interns inexperienced in the technique of spinal anesthesia or dural puncture and within 12 months of graduating from medical school, were randomly assigned to a conventional or a simulator-based teaching course of spinal anesthesia: 13 were recruited to the Conventional Group (CG) and 14 to the Simulator Group (SG). MEASUREMENTS: A SenseGraphic Immersive workbench and a modified Phantom desktop with shutter glasses were used to create a teaching environment. Outcomes of teaching were assessed in two phases within three weeks of the teaching course: Phase I consisted of a written examination followed by assessment on the simulator. A global rating scale and a task-specific checklist were used. Phase II (for those participants for whom a suitable opportunity arose to perform spinal anesthesia under supervision within three wks of the teaching course) consisted of structured observation of clinical performance of the procedure in the operating room. Participants were assessed by independent, study-blinded experts. Student\\'s two-tailed impaired t-tests were used to compare the parametric outcomes (P < 0.05 was considered significant). MAIN RESULTS: All participants completed the written test successfully with no difference between groups. Ten participants from CG and 13 from SG completed the simulator-based testing performing similarly in terms of the global rating scale. Five participants in CG and 6 in SG proceeded to clinical testing. On the global rating scale, interns in SG scored higher than those in CG. They performed similarly according to the task-specific checklist. CONCLUSIONS: Overall, no difference was measured between those taught with

Preliminary Flight Results of the Microelectronics and Photonics Test Bed: NASA DR1773 Fiber Optic Data Bus Experiment

Science.gov (United States)

Jackson, George L.; LaBel, Kenneth A.; Marshall, Cheryl; Barth, Janet; Seidleck, Christina; Marshall, Paul

1998-01-01

NASA Goddard Spare Flight Center's (GSFC) Dual Rate 1773 (DR1773) Experiment on the Microelectronic and Photonic Test Bed (MPTB) has provided valuable information on the performance of the AS 1773 fiber optic data bus in the space radiation environment. Correlation of preliminary experiment data to ground based radiation test results show the AS 1773 bus is employable in future spacecraft applications requiring radiation tolerant communication links.

Preliminary Results of Clover and Grass Coverage and Total Dry Matter Estimation in Clover-Grass Crops Using Image Analysis

Directory of Open Access Journals (Sweden)

Anders K. Mortensen

2017-12-01

Full Text Available The clover-grass ratio is an important factor in composing feed ratios for livestock. Cameras in the field allow the user to estimate the clover-grass ratio using image analysis; however, current methods assume the total dry matter is known. This paper presents the preliminary results of an image analysis method for non-destructively estimating the total dry matter of clover-grass. The presented method includes three steps: (1 classification of image illumination using a histogram of the difference in excess green and excess red; (2 segmentation of clover and grass using edge detection and morphology; and (3 estimation of total dry matter using grass coverage derived from the segmentation and climate parameters. The method was developed and evaluated on images captured in a clover-grass plot experiment during the spring growing season. The preliminary results are promising and show a high correlation between the image-based total dry matter estimate and the harvested dry matter ( R 2 = 0.93 with an RMSE of 210 kg ha − 1 .

NNWSI Phase II materials interaction test procedure and preliminary results

International Nuclear Information System (INIS)

Bates, J.K.; Gerding, T.J.

1985-01-01

The Nevada Nuclear Waste Storage Investigations (NNWSI) project is investigating the volcanic tuff beds of Yucca Mountain, Nevada, as a potential location for a high-level radioactive waste repository. This report describes a test method (Phase II) that has been developed to measure the release of radionuclides from the waste package under simulated repository conditions, and provides information on materials interactions that may occur in the repository. The results of 13 weeks of testing using the method are presented, and an analog test is described that investigates the relationship between the test method and expected repository conditions. 9 references, 10 figures, 11 tables

Particle-in-cell simulations of electron transport from plasma turbulence: recent progress in gyrokinetic particle simulations of turbulent plasmas

International Nuclear Information System (INIS)

Lin, Z; Rewoldt, G; Ethier, S; Hahm, T S; Lee, W W; Lewandowski, J L V; Nishimura, Y; Wang, W X

2005-01-01

Recent progress in gyrokinetic particle-in-cell simulations of turbulent plasmas using the gyrokinetic toroidal code (GTC) is surveyed. In particular, recent results for electron temperature gradient (ETG) modes and their resulting transport are presented. Also, turbulence spreading, and the effects of the parallel nonlinearity, are described. The GTC code has also been generalized for non-circular plasma cross-section, and initial results are presented. In addition, two distinct methods of generalizing the GTC code to be electromagnetic are described, along with preliminary results. Finally, a related code, GTC-Neo, for calculating neoclassical fluxes, electric fields, and velocities, are described

Cosmological simulations using a static scalar-tensor theory

Energy Technology Data Exchange (ETDEWEB)

RodrIguez-Meza, M A [Depto. de Fisica, Instituto Nacional de Investigaciones Nucleares, Col. Escandon, Apdo. Postal 18-1027, 11801 Mexico D.F (Mexico); Gonzalez-Morales, A X [Departamento Ingenierias, Universidad Iberoamericana, Prol. Paseo de la Reforma 880 Lomas de Santa Fe, Mexico D.F. Mexico (Mexico); Gabbasov, R F [Depto. de Fisica, Instituto Nacional de Investigaciones Nucleares, Col. Escandon, Apdo. Postal 18-1027, 11801 Mexico D.F (Mexico); Cervantes-Cota, Jorge L [Depto. de Fisica, Instituto Nacional de Investigaciones Nucleares, Col. Escandon, Apdo. Postal 18-1027, 11801 Mexico D.F (Mexico)

2007-11-15

We present {lambda}CDM N-body cosmological simulations in the framework of of a static general scalar-tensor theory of gravity. Due to the influence of the non-minimally coupled scalar field, the gravitational potential is modified by a Yukawa type term, yielding a new structure formation dynamics. We present some preliminary results and, in particular, we compute the density and velocity profiles of the most massive group.

Preliminary results of local earthquake tomography around Bali, Lombok, and Sumbawa regions

Energy Technology Data Exchange (ETDEWEB)

Nugraha, Andri Dian, E-mail: nugraha@gf.itb.ac.id; Puspito, Nanang T; Yudistira, Tedi [Global Geophysical Reserach Group, Faculty of Mining and Petroleum Engineering, Institute of Technology Bandung, JlGanesa 10, Bandung, 40132 (Indonesia); Kusnandar, Ridwan; Sakti, Artadi Pria [Meteorological, Climatological, and Geophysical Agency (MCGA) of Indonesian, Jakarta (Indonesia)

2015-04-24

Bali, Sumbawa, and Lombok regions are located in active tectonic influence by Indo-Australia plate subducts beneath Sunda plate in southern part and local back-arc thrust in northern part the region. Some active volcanoes also lie from eastern part of Java, Bali, Lombok and Sumbawa regions. Previous studies have conducted subsurface seismic velocity imaging using regional and global earthquake data around the region. In this study, we used P-arrival time from local earthquake networks compiled by MCGA, Indonesia within time periods of 2009 up to 2013 to determine seismic velocity structure and simultaneously hypocenter adjustment by applying seismic tomography inversion method. For the tomographic inversion procedure, we started from 1-D initial velocity structure. We evaluated the resolution of tomography inversion results through checkerboard test and calculating derivative weigh sum. The preliminary results of tomography inversion show fairly clearly high seismic velocity subducting Indo-Australian and low velocity anomaly around volcano regions. The relocated hypocenters seem to cluster around the local fault system such as back-arc thrust fault in northern part of the region and around local fault in Sumbawa regions. Our local earthquake tomography results demonstrated consistent with previous studies and improved the resolution. For future works, we will determine S-wave velocity structure using S-wave arrival time to enhance our understanding of geological processes and for much better interpretation.

Relativistic (3+1) dimensional hydrodynamic simulations of compact interacting binary systems

International Nuclear Information System (INIS)

Mathews, G.J.; Evans, C.R.; Wilson, J.R.

1986-09-01

We discuss the development of a relativistic hydrodynamic code for describing the evolution of astrophysical systems in three spatial dimensions. The application of this code to several test problems is presented. Preliminary results from the simulation of the dynamics of accreting binary white dwarf and neutron star systems are discussed. 14 refs., 4 figs

Varfarin in the complex treatment of antiphospholipid syndrome: preliminary results

Directory of Open Access Journals (Sweden)

T M Reshetnyak

2003-01-01

Full Text Available Objective. To assess efficacy and tolerance of varfarin in prophylaxis and therapy of thrombotic complications in patients with antiphospholipid syndrome (APS. Methods. 20 pts with APS (5 male and 15 female received varfarin during a year. 8 of them had primary APS (PAPS and 12 -systemic lupus erythematosus with APS (SLE+APS. 2 other pts (I with SLE+APS and I with PAPS received varfarin during the last 4 years. Nobody from 9 pts with PAPS received corticosteroids (CS. In SLE+APS pts CS dose varied from 4 to 20 mg/day and was not increased during follow up. During the study prothrombine time (PT was examined with thromboplastin ( manufactured by Renam having international sensitivity index 1,2 and international normalization relation (INR. Depending on treatment scheme APS pts were divided into 3 groups. Group 1 included 8 pts with INR<2,0, Group 2-7 with INR >3,0, group 3 - 7 pts with INR<2,0 receiving as additional treatment thrombo ASS 100 mg/day and vasonit from 600 to 1200 mg/day. Results. Two pts with INR = 1,8 had thrombosis recurrence (due to leg thrombophlebitis. There were no recurrences in other groups. 2 from 22 pts had "large" bleedings. "Small" bleedings episodes were noted in 7 from 22 pts. Largely that were subcutaneous bleedings (in 4 pts no more than 5 cm of size. Two pts receiving varfarin with INR 1,8 and 2,4 had renal colic. Conclusion. Our preliminary results prove the necessity of inclusion of varfarin in the treatment of pts with APS and thrombosis but intensive anticoagulant effect is not always desired.

Comparisons of the simulation results using different codes for ADS spallation target

International Nuclear Information System (INIS)

Yu Hongwei; Fan Sheng; Shen Qingbiao; Zhao Zhixiang; Wan Junsheng

2002-01-01

The calculations to the standard thick target were made by using different codes. The simulation of the thick Pb target with length of 60 cm, diameter of 20 cm bombarded with 800, 1000, 1500 and 2000 MeV energetic proton beam was carried out. The yields and the spectra of emitted neutron were studied. The spallation target was simulated by SNSP, SHIELD, DCM/CEM (Dubna Cascade Model /Cascade Evaporation Mode) and LAHET codes. The Simulation Results were compared with experiments. The comparisons show good agreement between the experiments and the SNSP simulated leakage neutron yield. The SHIELD simulated leakage neutron spectra are in good agreement with the LAHET and the DCM/CEM simulated leakage neutron spectra

Preliminary results of measurement of natural environmental radiation levels and doses to population in China

International Nuclear Information System (INIS)

Wang Qiliang; He Miaoting; Shu Qi

1985-01-01

In this paper the preliminary results of measurement of natural environmental radiation levels in China with RSS-111 high pressure ionization chamber and estimated doses to population are reported. A total of 2,723 indoor locales throughout China were measured. The results showed that the average absorbed dose rates in air due to gamma radiation for indoors and outdoors were 11.0 x 10 -8 Gy.h -1 and 7.4 x 10 -8 Gy.h -1 , respectively, and those due to cosmic rays were 3.2 x 10 -8 Gy.h -1 and 3.7 x 10 -8 Gy.h -1 , respectively. The annual average effective dose equivalent to population was 919 μSv, including 630 μSv from natural gamma radiation and 289 μSv from cosmic rays

An electromechanical gait trainer for restoration of gait in hemiparetic stroke patients: preliminary results.

Science.gov (United States)

Hesse, S; Werner, C; Uhlenbrock, D; von Frankenberg, S; Bardeleben, A; Brandl-Hesse, B

2001-01-01

Modern concepts of gait rehabilitation after stroke favor a task-specific repetitive approach. In practice, the required physical effort of the therapists limits the realization of this approach. Therefore, a mechanized gait trainer enabling nonambulatory patients to have the repetitive practice of a gait-like movement without overstraining therapists was constructed. This preliminary study investigated whether an additional 4-week daily therapy on the gait trainer could improve gait ability in 14 chronic wheelchair-bound hemiparetic subjects. The 4 weeks of physiotherapy and gait-trainer therapy resulted in a relevant improvement of gait ability in all subjects. Velocity, cadence, and stride length improved significantly (p gait trainer seems feasible as an adjunctive tool in gait rehabilitation after stroke; further studies are needed.

Hydrograph simulation models of the Hillsborough and Alafia Rivers, Florida: a preliminary report

Science.gov (United States)

Turner, James F.

1972-01-01

Mathematical (digital) models that simulate flood hydrographs from rainfall records have been developed for the following gaging stations in the Hillsborough and Alafia River basins of west-central Florida: Hillsborough River near Tampa, Alafia River at Lithia, and north Prong Alafia River near Keysville. These models, which were developed from historical streamflow and and rainfall records, are based on rainfall-runoff and unit-hydrograph procedures involving an arbitrary separation of the flood hydrograph. These models assume the flood hydrograph to be composed of only two flow components, direct (storm) runoff, and base flow. Expressions describing these two flow components are derived from streamflow and rainfall records and are combined analytically to form algorithms (models), which are programmed for processing on a digital computing system. Most Hillsborough and Alafia River flood discharges can be simulated with expected relative errors less than or equal to 30 percent and flood peaks can be simulated with average relative errors less than 15 percent. Because of the inadequate rainfall network that is used in obtaining input data for the North Prong Alafia River model, simulated peaks are frequently in error by more than 40 percent, particularly for storms having highly variable areal rainfall distribution. Simulation errors are the result of rainfall sample errors and, to a lesser extent, model inadequacy. Data errors associated with the determination of mean basin precipitation are the result of the small number and poor areal distribution of rainfall stations available for use in the study. Model inadequacy, however, is attributed to the basic underlying theory, particularly the rainfall-runoff relation. These models broaden and enhance existing water-management capabilities within these basins by allowing the establishment and implementation of programs providing for continued development in these areas. Specifically, the models serve not only as a

Biologically Inspired Visual Model With Preliminary Cognition and Active Attention Adjustment.

Science.gov (United States)

Qiao, Hong; Xi, Xuanyang; Li, Yinlin; Wu, Wei; Li, Fengfu

2015-11-01

Recently, many computational models have been proposed to simulate visual cognition process. For example, the hierarchical Max-Pooling (HMAX) model was proposed according to the hierarchical and bottom-up structure of V1 to V4 in the ventral pathway of primate visual cortex, which could achieve position- and scale-tolerant recognition. In our previous work, we have introduced memory and association into the HMAX model to simulate visual cognition process. In this paper, we improve our theoretical framework by mimicking a more elaborate structure and function of the primate visual cortex. We will mainly focus on the new formation of memory and association in visual processing under different circumstances as well as preliminary cognition and active adjustment in the inferior temporal cortex, which are absent in the HMAX model. The main contributions of this paper are: 1) in the memory and association part, we apply deep convolutional neural networks to extract various episodic features of the objects since people use different features for object recognition. Moreover, to achieve a fast and robust recognition in the retrieval and association process, different types of features are stored in separated clusters and the feature binding of the same object is stimulated in a loop discharge manner and 2) in the preliminary cognition and active adjustment part, we introduce preliminary cognition to classify different types of objects since distinct neural circuits in a human brain are used for identification of various types of objects. Furthermore, active cognition adjustment of occlusion and orientation is implemented to the model to mimic the top-down effect in human cognition process. Finally, our model is evaluated on two face databases CAS-PEAL-R1 and AR. The results demonstrate that our model exhibits its efficiency on visual recognition process with much lower memory storage requirement and a better performance compared with the traditional purely computational

Preliminary study for small animal preclinical hadrontherapy facility

Energy Technology Data Exchange (ETDEWEB)

Russo, G. [Institute of Molecular Bioimaging and Physiology, IBFM CNR-LATO, Cefalú (Italy); Pisciotta, P., E-mail: pietro.pisciotta@ibfm.cnr.it [Institute of Molecular Bioimaging and Physiology, IBFM CNR-LATO, Cefalú (Italy); National Institute for Nuclear Physics, Laboratori Nazionali del Sud, INFN-LNS, Catania (Italy); Cirrone, G.A.P.; Romano, F. [National Institute for Nuclear Physics, Laboratori Nazionali del Sud, INFN-LNS, Catania (Italy); Cammarata, F.; Marchese, V.; Forte, G.I.; Lamia, D.; Minafra, L.; Bravatá, V. [Institute of Molecular Bioimaging and Physiology, IBFM CNR-LATO, Cefalú (Italy); Acquaviva, R. [University of Catania, Catania (Italy); Gilardi, M.C. [Institute of Molecular Bioimaging and Physiology, IBFM CNR-LATO, Cefalú (Italy); Cuttone, G. [National Institute for Nuclear Physics, Laboratori Nazionali del Sud, INFN-LNS, Catania (Italy)

2017-02-21

Aim of this work is the study of the preliminary steps to perform a particle treatment of cancer cells inoculated in small animals and to realize a preclinical hadrontherapy facility. A well-defined dosimetric protocol was developed to explicate the steps needed in order to perform a precise proton irradiation in small animals and achieve a highly conformal dose into the target. A precise homemade positioning and holding system for small animals was designed and developed at INFN-LNS in Catania (Italy), where an accurate Monte Carlo simulation was developed, using Geant4 code to simulate the treatment in order to choose the best animal position and perform accurately all the necessary dosimetric evaluations. The Geant4 application can also be used to realize dosimetric studies and its peculiarity consists in the possibility to introduce the real target composition in the simulation using the DICOM micro-CT image. This application was fully validated comparing the results with the experimental measurements. The latter ones were performed at the CATANA (Centro di AdroTerapia e Applicazioni Nucleari Avanzate) facility at INFN-LNS by irradiating both PMMA and water solid phantom. Dosimetric measurements were performed using previously calibrated EBT3 Gafchromic films as a detector and the results were compared with the Geant4 simulation ones. In particular, two different types of dosimetric studies were performed: the first one involved irradiation of a phantom made up of water solid slabs where a layer of EBT3 was alternated with two different slabs in a sandwich configuration, in order to validate the dosimetric distribution. The second one involved irradiation of a PMMA phantom made up of a half hemisphere and some PMMA slabs in order to simulate a subcutaneous tumour configuration, normally used in preclinical studies. In order to evaluate the accordance between experimental and simulation results, two different statistical tests were made: Kolmogorov test and

Preliminary study for small animal preclinical hadrontherapy facility

Science.gov (United States)

Russo, G.; Pisciotta, P.; Cirrone, G. A. P.; Romano, F.; Cammarata, F.; Marchese, V.; Forte, G. I.; Lamia, D.; Minafra, L.; Bravatá, V.; Acquaviva, R.; Gilardi, M. C.; Cuttone, G.

2017-02-01

Aim of this work is the study of the preliminary steps to perform a particle treatment of cancer cells inoculated in small animals and to realize a preclinical hadrontherapy facility. A well-defined dosimetric protocol was developed to explicate the steps needed in order to perform a precise proton irradiation in small animals and achieve a highly conformal dose into the target. A precise homemade positioning and holding system for small animals was designed and developed at INFN-LNS in Catania (Italy), where an accurate Monte Carlo simulation was developed, using Geant4 code to simulate the treatment in order to choose the best animal position and perform accurately all the necessary dosimetric evaluations. The Geant4 application can also be used to realize dosimetric studies and its peculiarity consists in the possibility to introduce the real target composition in the simulation using the DICOM micro-CT image. This application was fully validated comparing the results with the experimental measurements. The latter ones were performed at the CATANA (Centro di AdroTerapia e Applicazioni Nucleari Avanzate) facility at INFN-LNS by irradiating both PMMA and water solid phantom. Dosimetric measurements were performed using previously calibrated EBT3 Gafchromic films as a detector and the results were compared with the Geant4 simulation ones. In particular, two different types of dosimetric studies were performed: the first one involved irradiation of a phantom made up of water solid slabs where a layer of EBT3 was alternated with two different slabs in a sandwich configuration, in order to validate the dosimetric distribution. The second one involved irradiation of a PMMA phantom made up of a half hemisphere and some PMMA slabs in order to simulate a subcutaneous tumour configuration, normally used in preclinical studies. In order to evaluate the accordance between experimental and simulation results, two different statistical tests were made: Kolmogorov test and

Preliminary study for small animal preclinical hadrontherapy facility

International Nuclear Information System (INIS)

Russo, G.; Pisciotta, P.; Cirrone, G.A.P.; Romano, F.; Cammarata, F.; Marchese, V.; Forte, G.I.; Lamia, D.; Minafra, L.; Bravatá, V.; Acquaviva, R.; Gilardi, M.C.; Cuttone, G.

2017-01-01

Aim of this work is the study of the preliminary steps to perform a particle treatment of cancer cells inoculated in small animals and to realize a preclinical hadrontherapy facility. A well-defined dosimetric protocol was developed to explicate the steps needed in order to perform a precise proton irradiation in small animals and achieve a highly conformal dose into the target. A precise homemade positioning and holding system for small animals was designed and developed at INFN-LNS in Catania (Italy), where an accurate Monte Carlo simulation was developed, using Geant4 code to simulate the treatment in order to choose the best animal position and perform accurately all the necessary dosimetric evaluations. The Geant4 application can also be used to realize dosimetric studies and its peculiarity consists in the possibility to introduce the real target composition in the simulation using the DICOM micro-CT image. This application was fully validated comparing the results with the experimental measurements. The latter ones were performed at the CATANA (Centro di AdroTerapia e Applicazioni Nucleari Avanzate) facility at INFN-LNS by irradiating both PMMA and water solid phantom. Dosimetric measurements were performed using previously calibrated EBT3 Gafchromic films as a detector and the results were compared with the Geant4 simulation ones. In particular, two different types of dosimetric studies were performed: the first one involved irradiation of a phantom made up of water solid slabs where a layer of EBT3 was alternated with two different slabs in a sandwich configuration, in order to validate the dosimetric distribution. The second one involved irradiation of a PMMA phantom made up of a half hemisphere and some PMMA slabs in order to simulate a subcutaneous tumour configuration, normally used in preclinical studies. In order to evaluate the accordance between experimental and simulation results, two different statistical tests were made: Kolmogorov test and

SARDA HITL Preliminary Human Factors Measures and Analyses

Science.gov (United States)

Hyashi, Miwa; Dulchinos, Victoria

2012-01-01

Human factors data collected during the SARDA HITL Simulation Experiment include a variety of subjective measures, including the NASA TLX, questionnaire questions regarding situational awareness, advisory usefulness, UI usability, and controller trust. Preliminary analysis of the TLX data indicate that workload may not be adversely affected by use of the advisories, additionally, the controller's subjective ratings of the advisories may suggest acceptance of the tool.

Preliminary uncertainty analysis of pre-waste-emplacement groundwater travel times for a proposed repository in basalt

International Nuclear Information System (INIS)

Clifton, P.M.; Arnett, R.C.

1984-01-01

Preliminary uncertainty analyses of pre-waste-emplacement groundwater travel times are presented for a potential high-level nuclear waste repository in the deep basalts beneath the Hanford Site, Washington State. The uncertainty analyses are carried out by means of a Monte Carlo technique, which requires the uncertain inputs to be described as either random variables or spatial stochastic processes. Pre-waste-emplacement groundwater travel times are modeled in a continuous, flat-lying basalt flow top that is assumed to overlie the repository horizon. Two-dimensional, steady state groundwater flow is assumed, and transmissivity, effective thickness, and regional hydraulic gradient are considered as uncertain inputs. Groundwater travel time distributions corresponding to three groundwater models are presented and compared. Limitations of these preliminary simulation results are discussed in detail

Functional magnetic resonance imaging in disorders of consciousness: preliminary results of an innovative analysis of brain connectivity.

Science.gov (United States)

De Pasquale, Francesco; Caravasso, Chiara Falletta; Péran, Patrice; Catani, Sheila; Tuovinen, Noora; Sabatini, Umberto; Formisano, Rita

2015-01-01

The aim of this preliminary study was to present a new approach for connectivity analysis in patients with severe acquired brain injury (ABI) that overcomes some of the difficulties created by anatomical abnormalities due to the brain injury. Using a data-driven approach, resting-state structural MRI (sMRI) and functional MRI (fMRI) data from three severe ABI patients - two with disorders of consciousness (DOC) and one who had recovered consciousness (non-DOC) - were integrated and analyzed. Parameters extracted from the distribution of the connectivity values, such as mean, standard deviation and skeweness, were considered. The distribution parameters estimated seem to provide an accurate multivariate classification of the considered cases that can be summarized as follows: connectivity in the severe ABI patients with DOC was on average lower than in the severe ABI non-DOC patient and healthy subjects. The dispersion of connectivity values of the severe ABI patients, non-DOC and DOC, was comparable, however the shape of the distribution was different in the non-DOC patient. Eventually, seed-based connectivity maps of the default mode Functional magnetic resonance imaging in disorders of consciousness: preliminary results of an innovative analysis of brain connectivity network show a pattern of increasing disruption of this network from the healthy subjects to non-DOC and DOC patients. Consistent results are obtained using an ICA-based approach..

A preliminary evaluation of the training effects of a didactic and simulation-based psychological first aid program in students and school counselors in South Korea.

Science.gov (United States)

Lee, Jong-Sun; You, Sungeun; Choi, Yun-Kyeung; Youn, Hyae-Young; Shin, Hye Sook

2017-01-01

The present study aimed to examine the training effects of a didactic and simulation-based psychological first aid (PFA) program. Based on the competency-based model, the study sought to examine whether the PFA training would enhance knowledge, skills, and attitudes. Study 1 examined the training effects of the PFA program in a sample of undergraduate and graduate students in psychology. Study 2 was conducted with school counselors. In both studies, all participants completed a one-day PFA workshop with a 3-hour didactic lecture and a 3-hour simulation-based practice. Assessments were conducted prior to the didactic lecture and upon completion of the simulation-based practice. In study 1, an examination of pre- and posttest comparisons indicated that the training significantly improved students' PFA knowledge and perceived competence in PFA skill. In study 2, the same PFA training significantly improved school counselors' PFA knowledge, perceived competence in PFA skill, perceived preparedness and confidence to provide psychological assistance for future disasters, but their perceived willingness to participate in psychological assistance did not significantly change after the training. This study provides preliminary evidence supporting the effectiveness of the PFA training program using a combined method of didactic and simulation-based practice for disaster mental health providers in Korea.

A preliminary evaluation of the training effects of a didactic and simulation-based psychological first aid program in students and school counselors in South Korea.

Directory of Open Access Journals (Sweden)

Jong-Sun Lee

Full Text Available The present study aimed to examine the training effects of a didactic and simulation-based psychological first aid (PFA program. Based on the competency-based model, the study sought to examine whether the PFA training would enhance knowledge, skills, and attitudes. Study 1 examined the training effects of the PFA program in a sample of undergraduate and graduate students in psychology. Study 2 was conducted with school counselors. In both studies, all participants completed a one-day PFA workshop with a 3-hour didactic lecture and a 3-hour simulation-based practice. Assessments were conducted prior to the didactic lecture and upon completion of the simulation-based practice. In study 1, an examination of pre- and posttest comparisons indicated that the training significantly improved students' PFA knowledge and perceived competence in PFA skill. In study 2, the same PFA training significantly improved school counselors' PFA knowledge, perceived competence in PFA skill, perceived preparedness and confidence to provide psychological assistance for future disasters, but their perceived willingness to participate in psychological assistance did not significantly change after the training. This study provides preliminary evidence supporting the effectiveness of the PFA training program using a combined method of didactic and simulation-based practice for disaster mental health providers in Korea.

A color spectrographic phonocardiography (CSP applied to the detection and characterization of heart murmurs: preliminary results

Directory of Open Access Journals (Sweden)

Hassani Kamran

2011-05-01

Full Text Available Abstract Background Although cardiac auscultation remains important to detect abnormal sounds and murmurs indicative of cardiac pathology, the application of electronic methods remains seldom used in everyday clinical practice. In this report we provide preliminary data showing how the phonocardiogram can be analyzed using color spectrographic techniques and discuss how such information may be of future value for noninvasive cardiac monitoring. Methods We digitally recorded the phonocardiogram using a high-speed USB interface and the program Gold Wave http://www.goldwave.com in 55 infants and adults with cardiac structural disease as well as from normal individuals and individuals with innocent murmurs. Color spectrographic analysis of the signal was performed using Spectrogram (Version 16 as a well as custom MATLAB code. Results Our preliminary data is presented as a series of seven cases. Conclusions We expect the application of spectrographic techniques to phonocardiography to grow substantially as ongoing research demonstrates its utility in various clinical settings. Our evaluation of a simple, low-cost phonocardiographic recording and analysis system to assist in determining the characteristic features of heart murmurs shows promise in helping distinguish innocent systolic murmurs from pathological murmurs in children and is expected to useful in other clinical settings as well.

Comparison of multiple-criteria decision-making methods - results of simulation study

Directory of Open Access Journals (Sweden)

Michał Adamczak

2016-12-01

Full Text Available Background: Today, both researchers and practitioners have many methods for supporting the decision-making process. Due to the conditions in which supply chains function, the most interesting are multi-criteria methods. The use of sophisticated methods for supporting decisions requires the parameterization and execution of calculations that are often complex. So is it efficient to use sophisticated methods? Methods: The authors of the publication compared two popular multi-criteria decision-making methods: the  Weighted Sum Model (WSM and the Analytic Hierarchy Process (AHP. A simulation study reflects these two decision-making methods. Input data for this study was a set of criteria weights and the value of each in terms of each criterion. Results: The iGrafx Process for Six Sigma simulation software recreated how both multiple-criteria decision-making methods (WSM and AHP function. The result of the simulation was a numerical value defining the preference of each of the alternatives according to the WSM and AHP methods. The alternative producing a result of higher numerical value  was considered preferred, according to the selected method. In the analysis of the results, the relationship between the values of the parameters and the difference in the results presented by both methods was investigated. Statistical methods, including hypothesis testing, were used for this purpose. Conclusions: The simulation study findings prove that the results obtained with the use of two multiple-criteria decision-making methods are very similar. Differences occurred more frequently in lower-value parameters from the "value of each alternative" group and higher-value parameters from the "weight of criteria" group.

Principle and preliminary results of the whole-body scintigraphic unit Omniview

International Nuclear Information System (INIS)

Methlin, G.; Jung, G.M.; Gerard, G.

The Picker Company has recently launched a system adapted to its Dynacamera for the production of whole-body scintigraphs. For the last few months the radioisotopes service of the Strasbourg Anti-Cancer Centre has been in possession of such a system, intended mainly for systematic research on metastases, especially of the bone, and on the degree of extension of tumours. On the basis of the short experience so far acquired the report is limited to an outline of the working principle of this device, the presentation of preliminary documents and a few critical remarks summing up first impressions [fr

Preliminary results of studies of the Valea Morilor Upper Palaeolithic site (Chisinau, Republic of Moldova) : A new camp of mammoth hunters

NARCIS (Netherlands)

Obada, Teodor; van der Plicht, Johannes; Markova, Anastasia; Prepelitsa, Afanasie

2012-01-01

Preliminary results are presented from the studies of a newly found Paleolithic site - Valea Morilor (Chisingu, Republic of Moldova). The excavations produced unquestionable evidence of mammoth hunting (Mammuthus primigenius Blumenbach, 1799). Excavations of 2009-2010 opened an area of 1264 m(2).

Integrated visualization of simulation results and experimental devices in virtual-reality space

International Nuclear Information System (INIS)

Ohtani, Hiroaki; Ishiguro, Seiji; Shohji, Mamoru; Kageyama, Akira; Tamura, Yuichi

2011-01-01

We succeeded in integrating the visualization of both simulation results and experimental device data in virtual-reality (VR) space using CAVE system. Simulation results are shown using Virtual LHD software, which can show magnetic field line, particle trajectory, and isosurface of plasma pressure of the Large Helical Device (LHD) based on data from the magnetohydrodynamics equilibrium simulation. A three-dimensional mouse, or wand, determines the initial position and pitch angle of a drift particle or the starting point of a magnetic field line, interactively in the VR space. The trajectory of a particle and the stream-line of magnetic field are calculated using the Runge-Kutta-Huta integration method on the basis of the results obtained after pointing the initial condition. The LHD vessel is objectively visualized based on CAD-data. By using these results and data, the simulated LHD plasma can be interactively drawn in the objective description of the LHD experimental vessel. Through this integrated visualization, it is possible to grasp the three-dimensional relationship of the positions between the device and plasma in the VR space, opening a new path in contribution to future research. (author)

Ayahuasca-assisted therapy for addiction: results from a preliminary observational study in Canada.

Science.gov (United States)

Thomas, Gerald; Lucas, Philippe; Capler, N Rielle; Tupper, Kenneth W; Martin, Gina

2013-03-01

This paper reports results from a preliminary observational study of ayahuasca-assisted treatment for problematic substance use and stress delivered in a rural First Nations community in British Columbia, Canada. The "Working with Addiction and Stress" retreats combined four days of group counselling with two expert-led ayahuasca ceremonies. This study collected pre-treatment and six months follow-up data from 12 participants on several psychological and behavioral factors related to problematic substance use, and qualitative data assessing the personal experiences of the participants six months after the retreat. Statistically significant (p ayahuasca-assisted therapy appears to be associated with statistically significant improvements in several factors related to problematic substance use among a rural aboriginal population. These findings suggest participants may have experienced positive psychological and behavioral changes in response to this therapeutic approach, and that more rigorous research of ayahuasca-assisted therapy for problematic substance use is warranted.

Aerobic Capacity Following Long Duration International Spaces Station (ISS) Missions: Preliminary Results

Science.gov (United States)

Moore, Alan D.; Lee, S.M.C.; Everett, M.E.; Guined, J.R.; Knudsen, P.

2010-01-01

Maximum oxygen uptake (VO2max) is reduced immediately following space flights lasting 6%. WRmax also decreased on R+1/2 compared to preflight (Pre: 245+/-69, R+1/2: 210+/-45 W). On R+10, VO2max was 2.86+/-0.62 L(dot)/min, with 2 subjects still demonstrating a loss of > 6% from preflight. WRmax on R+10 was 240+/-49 W. HRmax did not change from pre to post-flight. Conclusions: These preliminary results, from the first 5 of 12 planned subjects of an ongoing ISS study, suggest that the majority of astronauts will experience a decrease in VO2max after long-duration space-flight. Interestingly, the two astronauts with the highest preflight VO2max had the greatest loss on R+1/2, and the astronaut with the lowest preflight VO2max increased by 13%. Thus, maintenance of VO2max may be more difficult in astronauts who have a high aerobic capacity, perhaps requiring more intense in-flight exercise countermeasure prescriptions.

Preliminary Investigation on the Behavior of Pore Air Pressure During Rainfall Infiltration

Science.gov (United States)

Ashraf Mohamad Ismail, Mohd; Min, Ng Soon; Hasliza Hamzah, Nur; Hazreek Zainal Abidin, Mohd; Madun, Aziman; Tajudin, Saiful Azhar Ahmad

2018-04-01

This paper focused on the preliminary investigation of pore air pressure behaviour during rainfall infiltration in order to substantiate the mechanism of rainfall induced slope failure. The actual behaviour or pore air pressure during infiltration is yet to be clearly understood as it is regularly assumed as atmospheric. Numerical modelling of one dimensional (1D) soil column was utilized in this study to provide a preliminary insight of this highlighted uncertainty. Parametric study was performed by using rainfall intensities of 1.85 x 10-3m/s and 1.16 x 10-4m/s applied on glass beads to simulate intense and modest rainfall conditions. Analysis results show that the high rainfall intensity causes more development of pore air pressure compared to low rainfall intensity. This is because at high rainfall intensity, the rainwater cannot replace the pore air smoothly thus confining the pore air. Therefore, the effect of pore air pressure has to be taken into consideration particularly during heavy rainfall.

Shaping the future of production in South Africa: Preliminary country readiness results

CSIR Research Space (South Africa)

Saunders, M

2017-10-01

Full Text Available • Digital Security & Data Privacy • Industry Activity • Research Intensity • Available Financing • Labor Force Skills • Inclusivity • Migration • Education Outcomes • Agility & Adaptability • Trade Linkages • Trade Performance • Trade... and target sectors and value chain segments for growth 10 PRELIMINARY – FOR DISCUSSION High Potential Followers Legacy Champions Global Leaders Sectors Where to target growth? Value Chain Which segments to focus on? Inclusive Growth How to support...

Intraarterial Ultrasound in Pancreatic Cancer: Feasibility Study and Preliminary Results

International Nuclear Information System (INIS)

Larena-Avellaneda, Axel; Timm, Stephan; Kickuth, Ralph; Kenn, Werner; Steger, Ulrich; Jurowich, Christian; Germer, Christoph-Thomas

2010-01-01

Despite technological advances in computed tomography (CT) and magnetic resonance imaging, the involvement of the celiac or mesenteric artery in pancreatic cancer remains uncertain in many cases. Infiltration of these vessels is important in making decisions about therapy choices but often can only be definitively determined through laparotomy. Local (intraarterial) ultrasound may increase diagnostic accuracy. Using the Volcano intravascular ultrasound (IVUS) system, we applied a transfemoral method to scan the celiac and mesenteric arteries directly intraarterial. This technique was used in five patients with suspected pancreatic cancer. Technical success was achieved in all cases. In one case, a short dissection of the mesenteric artery occurred but could be managed interventionally. In tumors that did not contact with the vessels, IVUS was unable to display the tissue pathology. Our main interest was the infiltration of the arteries. In one case, infiltration was certain in the CT scan but uncertain in two patients. In the latter two cases, IVUS correctly predicted infiltration in one and freedom from tumor in the other case. In our preliminary study, IVUS correctly predicted arterial infiltration in all cases. IVUS did not provide new information when the tumor was far away from the vessel. Compared with IVUS in the portal vein, the information about the artery is more detailed, and the vessel approach is easier. These results encouraged us to design a prospective study to evaluate the sensitivity and specificity of this method.

Preliminary results from a high-pressure imaging spectroscopic proportional counter

International Nuclear Information System (INIS)

Hall, C.J.; Bazzano, A.; Lewis, R.A.; Parker, B.; Ubertini, P.; Worgan, J.S.

1992-01-01

A new type of high-pressure proportional counter, with both spatial resolution and spectroscopic capabilities is being jointly developed by the Istituto di Astrofisica Spaziale (CNR), Frascati, Italy and the SERC Daresbury Laboratory, Warrington, UK. The characteristics of the detector can be optimized for the particular requirement of the experiment, either for x-ray astronomy observations from space, or for the high count rate applications associated with a synchrotron light source. In its baseline configuration, the detector is filled to 5 bar with a xenon/quench gas mixture and will be sensitive over the energy range 5 keV to 150 keV (2.5 to 0.08 A). The positional resolution will range from 500 μm at the lower energies to around 1 mm at the higher end of the energy range. The current prototype has a sensitive area of 200x200 mm. The final version is hoped to have an area closer to 425x425 mm. The very small photon absorption length in the higher pressure gas allows the parallax effect, a feature of 1 atmosphere detectors, to be greatly reduced. The timing resolution (150 ns) of the detector enables both a high-rate capability and the possibility of the escape gate technique to achieve higher spectral resolution at energies > the Xe K edge. Preliminary results are presented showing the spectral and positional resolution for the prototype detector

Polyurethane-Covered Self-expandable Nitinol Stent for Malignant Biliary Obstruction: Preliminary Results

International Nuclear Information System (INIS)

Han, Young-Min; Hwang, Seung-Bae; Lee, Soo-Teik; Lee, Jeong-Min; Chung, Gyung-Ho

2002-01-01

Purpose: To evaluate the immediate and long-term results in ten patients with malignant biliary obstruction using a polyurethane-covered, self-expandable nitinol stent.Methods: A nitinol stent, fully covered with high-elasticity polyurethane, with an unconstrained diameter of 10 mm and a total length of 60-80 mm, was placed transhepatically under fluoroscopic guidance in ten patients. The length of the biliary obstruction varied between 30-50 mm. The follow-up examination included a clinical assessment, serum bilirubin measurement, and ultrasound examinations at one-month intervals in all patients. Results: Initial stent deployment was successful in eight patients. Two patients experienced proximal migration,which was solved by insertion of two, uncovered Wallstents. One patient had the stent removed after two weeks because of severe nausea and vomiting. One patient had delayed migration of the covered stent after 40 weeks. The follow-up duration was 3-40 weeks (Mean: 16.9 weeks). Seven patients died(3-26 weeks) and three patients survived (24-40 weeks). The bilirubin measurements in all patients had significantly decreased one week after stent insertion. The levels of amylase and lipase had did not increase after stent insertion. Conclusions: Apolyurethane-covered, self-expandable nitinol stent can be used effectively and safely in the treatment of malignant biliary obstruction. The preliminary results are favorable, but there is a need for further large studies to determine both long-term survival and patency

Diagnosis of breast cancer using elastic-scattering spectroscopy: preliminary clinical results

Science.gov (United States)

Bigio, Irving J.; Brown, Stephen G.; Briggs, Gavin M.; Kelley, Christine; Lakhani, Sunil; Pickard, David; Ripley, Paul M.; Rose, Ian; Saunders, Christobel

2000-04-01

We report on the first stages of a clinical study designed to test elastic-scattering spectroscopy, medicated by fiberoptic probes, for three specific clinical applications in breast-tissue diagnosis: (1) a transdermal-needle (interstitial) measurement for instant diagnosis with minimal invasiveness similar to fine-needle aspiration but with sensitivity to a larger tissue volume, (2) a hand-held diagnostic probe for use in assessing tumor/resection margins during open surgery, and (3) use of the same probe for real-time assessment of the `sentinel' node during surgery to determine the presence or absence of tumor (metastatic). Preliminary results from in vivo measurements on 31 women are encouraging. Optical spectra were measured on 72 histology sites in breast tissue, and 54 histology sites in sentinel nodes. Two different artificial intelligence methods of spectral classification were studied. Artificial neural networks yielded sensitivities of 69% and 58%, and specificities of 85% and 93%, for breast tissue and sentinel nodes, respectively. Hierarchical cluster analysis yielded sensitivities of 67% and 91%, and specificities of 79% and 77%, for breast tissue and sentinel nodes, respectively. These values are expected to improve as the data sets continue to grow and more sophisticated data preprocessing is employed. The study will enroll up to 400 patients over the next two years.

Doses in pediatric patients undergoing chest and abdomen CT examinations. Preliminary results

International Nuclear Information System (INIS)

Jornada, Tiago S.; Silva, Teogenes A. da

2011-01-01

Computed tomography (CT) is a non-invasive method of image production that imparts significant doses to a patient, it is expected that pediatric CT examinations will increase the risk of induced cancer in children. In this study the effective doses in a five year-old child submitted to chest or abdomen CT scans were assessed for comparison purposes. The CTEXPO computed program was used with data from routine protocols of a 0 to 13 year-old children in two public hospitals in Belo Horizonte. Hospital A used a Siemens Dual-Slice unit with 80 kV, 41 mA and pitch 2 for chest or abdomen; hospital B used a Multislice GE unit with 120 kV, 45 mA and pitch 1 for chest and 120 kV, 55 mA. and pitch 1 for abdomen. Results of effective doses in a five year-old child were 1.7 and 1.0 mSv in hospital A and 9.1 and 7.2 mSv in hospital B, for chest and abdomen, respectively. Results were compared to the reference effective doses of 7.2 and 5.0 mSv for chest and abdomen respectively that were derived from the air kerma length product values given in ICRP publication 87. Results of hospital A showed that low dose exposures also can be achieved in CT scans of children. Results showed that even a hospital with a modern facility (hospital B) can provided doses higher than reference values if protocols are not adjusted for children. Preliminary results suggested that there is a room for optimizing children exposure submitted to CT scans. (author)

Development and preliminary experimental study on micro-stacked insulator

International Nuclear Information System (INIS)

Ren Chengyan; Yuan Weiqun; Zhang Dongdong; Yan Ping; Wang Jue

2009-01-01

High gradient insulating technology is one of the key technologies in new type dielectric wall accelerator(DWA). High gradient insulator, namely micro-stacked insulator, was developed and preliminary experimental study was done. Based on the finite element and particle simulating method, surface electric field distribution and electron movement track of micro-stacked insulator were numerated, and then the optimized design proposal was put forward. Using high temperature laminated method, we developed micro-stacked insulator samples which uses exhaustive fluorinated ethylene propylene(FEP) as dielectric layer and stainless steel as metal layer. Preliminary experiment of vacuum surface flashover in nanosecond pulse voltage was done and micro-stacked insulator exhibited favorable vacuum surface flashover performance with flashover field strength of near 180 kV/cm. (authors)

Preliminary design for hot dirty-gas control-valve test facility. Final report

Energy Technology Data Exchange (ETDEWEB)

1980-01-01

This report presents the results of a preliminary design and cost estimating effort for a facility for the testing of control valves in Hot Dirty Gas (HDGCV) service. This design was performed by Mittelhauser Corporation for the United States Department of Energy's Morgantown Energy Technology Center (METC). The objective of this effort was to provide METC with a feasible preliminary design for a test facility which could be used to evaluate valve designs under simulated service conditions and provide a technology data base for DOE and industry. In addition to the actual preliminary design of the test facility, final design/construction/operating schedules and a facility cost estimate were prepared to provide METC sufficient information with which to evaluate this design. The bases, assumptions, and limitations of this study effort are given. The tasks carried out were as follows: METC Facility Review, Environmental Control Study, Gas Generation Study, Metallurgy Review, Safety Review, Facility Process Design, Facility Conceptual Layout, Instrumentation Design, Cost Estimates, and Schedules. The report provides information regarding the methods of approach used in the various tasks involved in the completion of this study. Section 5.0 of this report presents the results of the study effort. The results obtained from the above-defined tasks are described briefly. The turnkey cost of the test facility is estimated to be $9,774,700 in fourth quarter 1979 dollars, and the annual operating cost is estimated to be $960,000 plus utilities costs which are not included because unit costs per utility were not available from METC.

Environment modelling in near Earth space: Preliminary LDEF results

Science.gov (United States)

Coombs, C. R.; Atkinson, D. R.; Wagner, J. D.; Crowell, L. B.; Allbrooks, M.; Watts, A. J.

1992-01-01

Hypervelocity impacts by space debris cause not only local cratering or penetrations, but also cause large areas of damage in coated, painted or laminated surfaces. Features examined in these analyses display interesting morphological characteristics, commonly exhibiting a concentric ringed appearance. Virtually all features greater than 0.2 mm in diameter possess a spall zone in which all of the paint was removed from the aluminum surface. These spall zones vary in size from approximately 2 - 5 crater diameters. The actual craters in the aluminum substrate vary from central pits without raised rims, to morphologies more typical of craters formed in aluminum under hypervelocity laboratory conditions for the larger features. Most features also possess what is referred to as a 'shock zone' as well. These zones vary in size from approximately 1 - 20 crater diameters. In most cases, only the outer-most layer of paint was affected by this impact related phenomenon. Several impacts possess ridge-like structures encircling the area in which this outer-most paint layer was removed. In many ways, such features resemble the lunar impact basins, but on an extremely reduced scale. Overall, there were no noticeable penetrations, bulges or spallation features on the backside of the tray. On Row 12, approximately 85 degrees from the leading edge (RAM direction), there was approximately one impact per 15 cm(exp 2). On the trailing edge, there was approximately one impact per 72 cm(exp 2). Currently, craters on four aluminum experiment trays from Bay E09, directly on the leading edge are being measured and analyzed. Preliminary results have produced more than 2200 craters on approximately 1500 cm(exp 2) - or approximately 1 impact per 0.7 cm(exp 2).

Simulating motivated cognition

Science.gov (United States)

Gevarter, William B.

1991-01-01

A research effort to develop a sophisticated computer model of human behavior is described. A computer framework of motivated cognition was developed. Motivated cognition focuses on the motivations or affects that provide the context and drive in human cognition and decision making. A conceptual architecture of the human decision-making approach from the perspective of information processing in the human brain is developed in diagrammatic form. A preliminary version of such a diagram is presented. This architecture is then used as a vehicle for successfully constructing a computer program simulation Dweck and Leggett's findings that relate how an individual's implicit theories orient them toward particular goals, with resultant cognitions, affects, and behavior.

The use of simulation in teaching the basic sciences.

Science.gov (United States)

Eason, Martin P

2013-12-01

To assess the current use of simulation in medical education, specifically, the teaching of the basic sciences to accomplish the goal of improved integration. Simulation is increasingly being used by the institutions to teach the basic sciences. Preliminary data suggest that it is an effective tool with increased retention and learner satisfaction. Medical education is undergoing tremendous change. One of the directions of that change is increasing integration of the basic and clinical sciences to improve the efficiency and quality of medical education, and ultimately to improve the patient care. Integration is thought to improve the understanding of basic science conceptual knowledge and to better prepare the learners for clinical practice. Simulation because of its unique effects on learning is currently being successfully used by many institutions as a means to produce that integration through its use in the teaching of the basic sciences. Preliminary data indicate that simulation is an effective tool for basic science education and garners high learner satisfaction.

Simulation Results: Optimization of Contact Ratio for Interdigitated Back-Contact Solar Cells

Directory of Open Access Journals (Sweden)

Vinay Budhraja

2017-01-01

Full Text Available In the fabrication of interdigitated back contact (IBC solar cells, it is very important to choose the right size of contact to achieve the maximum efficiency. Line contacts and point contacts are the two possibilities, which are being chosen for IBC structure. It is expected that the point contacts would give better results because of the reduced recombination rate. In this work, we are simulating the effect of contact size on the performance of IBC solar cells. Simulations were done in three dimension using Quokka, which numerically solves the charge carrier transport. Our simulation results show that around 10% of contact ratio is able to achieve optimum cell efficiency.

FY2017 Report on NISC Measurements and Detector Simulations

Energy Technology Data Exchange (ETDEWEB)

Andrews, Madison Theresa [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Meierbachtol, Krista Cruse [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Jordan, Tyler Alexander [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-11-14

FY17 work focused on automation, both of the measurement analysis and comparison of simulations. The experimental apparatus was relocated and weeks of continuous measurements of the spontaneous fission source ²⁵²Cf was performed. Programs were developed to automate the conversion of measurements into ROOT data framework files with a simple terminal input. The complete analysis of the measurement (which includes energy calibration and the identification of correlated counts) can now be completed with a documented process which involves one simple execution line as well. Finally, the hurdles of slow MCNP simulations resulting in low simulation statistics have been overcome with the generation of multi-run suites which make use of the highperformance computing resources at LANL. Preliminary comparisons of measurements and simulations have been performed and will be the focus of FY18 work.

Preliminary tests in skull pediatric phantom for dosimetry in computerized tomography

International Nuclear Information System (INIS)

Martins, Elaine Wirney; Potiens, Maria da Penha de A.

2014-01-01

Computed tomography (CT) is one of the techniques in the field of radiology with striking technological advance in recent years. One reason for this was the increased number of channels associated with the increased power of the X-ray tube. These conditions allowed the equipment high speed in the acquisition of the cuts, reducing the patient exposure time essential characteristic for the increase of its use in pediatric patients. In this context, were developed a new pediatric skull simulator to analyze the results of measurements performed in laboratory and clinic beams with the objective of creation and use of diagnostic reference levels observing risks stochastic effects and assessing the reduction of absorbed doses in patients undergoing growing. Preliminary tests performed in clinical beams showed C w values: 2.525 ± 0.212 mGy for the developed simulator quoted and 3.362 ± 0.282 mGy for a simulator developed by IPEN called standard, both being between uncertainty values of 8.4% and 14.4% suggested by TRS number 457

Diffusion of oxygen in nitrogen in the pores of graphite. Preliminary results on the effect of oxidation on diffusivity

Energy Technology Data Exchange (ETDEWEB)

Hewitt, G. F.; Sharratt, E. W.

1962-10-15

Preliminary results are reported from an experimental study of the effect of burnoff on the diffusivity of oxygen in nitrogen within the pores of graphite. It is found that the ratio of effective diffusivity to ''free gas'' diffusivity changes about four-fold in the range 0-9% total oxidation. The viscous permeability, B₀, increases in almost the same proportion over the same range.

242Pu: Preliminary evaluation with consideration of 240Pu, and some sensitivity results

International Nuclear Information System (INIS)

Jary, J.; Lagrange, C.; Philis, C.

1978-01-01

A preliminary evaluation of 242 Pu nuclear data is presented for the neutron energy range from 10 keV to 20 MeV. The fission cross section is based upon recent experimental measurements on 242 Pu. The remaining cross sections have been calculated using various nuclear models with parameters obtained mainly by both fits on 240 Pu experimental data and general reflexions on the actinides. Particular care has been taken of the direct interactions. The laws of secondary neutron energy spectra and the average number of neutrons produced per fission have been evaluated. The results have been placed in ENDF/BIV format and combined with the low energy region of ENDF/BIV MAT = 1161 data to make complete the evaluation over the whole energy range 10 -5 eV - 20 MeV. Finally, the sensitivities of some of these nuclear data available for reactor calculations are given in terms of the variation of the calculated critical masses

Cognitive impairment and computer tomography image in patients with arterial hypertension -preliminary results

International Nuclear Information System (INIS)

Yaneva-Sirakova, T.; Tarnovska-Kadreva, R.; Traykov, L.; Zlatareva, D.

2012-01-01

Arterial hypertension is the leading risk factor for cognitive impairment, but it is developed only in some of the patients with pour control. On the other hand, not all of the patents with white matter changes have cognitive deficit. There may be a variety of reasons for this: the accuracy of methods for blood pressure measurement, the specific brain localization or some other reason. Here are the preliminary results of a study (or the potential correlation between self-measured, office-, ambulatory monitored blood pressure, central aortic blood pressure, minimal cognitive impairment and the specific brain image on contrast computer tomography. We expect to answer, the question whether central aortic or self-measured blood pressure have the leading role for the development of cognitive impairment in the presence of a specific neuroimaging finding, as well as what is the prerequisite for the clinical manifestation of cognitive dysfunction in patients with computer tomographic pathology. (authors)

Determinant method and quantum simulations of many-body effects in a single impurity Anderson model

International Nuclear Information System (INIS)

Gubernatis, J.E.; Olson, T.; Scalapino, D.J.; Sugar, R.L.

1985-01-01

A short description is presented of a quantum Monte Carlo technique, often referred to as the determinant method, that has proved useful for simulating many-body effects in systems of interacting fermions at finite temperatures. Preliminary results using this technique on a single impurity Anderson model are reported. Examples of such many-body effects as local moment formation, Kondo behavior, and mixed valence phenomena found in the simulations are shown. 10 refs., 3 figs

Simulation of Material Flow Through a Sample Divider

Directory of Open Access Journals (Sweden)

Jiří Rozbroj

2018-03-01

Full Text Available The prerequisite for a modern approach to innovative procedures of the development of current or even newly created equipment for the transport of particulate materials is the utilization of simulation methods, such as the Discrete Element Method (DEM. This article focuses on the basic, or initial, validation of movement of material through the sample divider. The mechanical-physical properties of brown coal were measured. Based on these parameters the preliminary input values for EDEM Academic were selected, and a simulation of the dividing process was run. The key monitored parameters included density and friction coefficient. Experiments on a realistic model of the equipment were performed and assessed. The total weights of brown coal at the exit from the divider were determined for a specific speed of the divider. The aim of this task was to simulate the realistically determined weight division of the brown coal sample. The result from the DEM was compared with the results of measurement on a realistic model.

Preliminary Report: DESiGN and Test Result of KSR-3 Rocket Magnetometers

Directory of Open Access Journals (Sweden)

Hyo-Min Kim

2000-12-01

Full Text Available The solar wind contributes to the formation of unique space environment called the Earth's magnetosphere by various interactions with the Earth's magnetic field. Thus the solar-terrestrial environment affects the Earth's magnetic field, which can be observed with an instrument for the magnetic field measurement, the magnetometer usually mounted on the rocket and the satellite and based on the ground observatory. The magnetometer is a useful instrument for the spacecraft attitude control as well as the Earth's magnetic field measurements for a scientific purpose. In this paper, we present the preliminary design and test results of the two onboard magnetometers of KARI's (Korea Aerospace Research Institute sounding rocket, KSR-3, which will be launched four times during the period of 2001-02. The KSR-3 magnetometers consist of the fluxgate magnetometer, MAG/AIM (Attitude Information Magnetometer for acquiring the rocket flight attitude information, and of the search-coil magnetometer, MAG/SIM (Scientific Investigation Magnetometer for the observation of the Earth's magnetic field fluctuations. With the MAG/AIM, the 3-axis attitude information can be acquired by the comparison of the resulting dc magnetic vector field with the IGRF (International Geomagnetic Reference Field. The Earth's magnetic field fluctuations ranging from 10 to 1,000 Hz can also be observed with the MAG/SIM measurement.

Simulation results of the electron-proton telescope for Solar Orbiter

Energy Technology Data Exchange (ETDEWEB)

Boden, Sebastian; Steinhagen, Jan; Kulkarni, Shrinivasrao; Grunau, Jan; Paspirgilis, Rolf; Martin, Cesar; Boettcher, Stephan; Seimetz, Lars; Schuster, Bjoern; Kulemzin, Alexander; Wimmer-Schweingruber, Robert F. [Christian-Albrechts-Universitaet Kiel (Germany)

2013-07-01

The Electron Proton Telescope (EPT) is one of five instruments in the Energetic Particle Detector suite for Solar Orbiter. It investigates low energy electrons and protons of solar events. EPT covers an energy range from 20400 keV for electrons and 20 keV-7 MeV for protons and distinguishes electrons from protons using a magnet/foil technique with silicon detectors. There will be two EPT units, each with double-barreled telescopes, one looking sunwards/antisunwards and the other north/south. EPT is designed using the GEometry ANd Tracking (GEANT) simulation toolkit developed by CERN for Monte Carlo calculations. Here we present the details of our simulations and the simulation results with respect to energy coverage and the geometrical factor of the EPT instrument. We also look at the far-field of the EPT magnets, which is important for electromagnetic cleanliness considerations.

Therapy of neuroendocrine carcinoma with Y-90 DOTA- preliminary results

International Nuclear Information System (INIS)

Artiko, V.; Obradovic, V.; Nadezda, N.; Djokic, D.; Jankovic, D.; Popovic, B.; Damjanovic, S.; Mikolajczak, R.; Pawlak, D.

2007-01-01

Full text: Aim: Cell membrane-specific somatostatin receptors are usually expressed by neuroendocrine tumors. Radiolabelled receptor-binding somatostatin analogues target tissues expressing these receptors and can be used for visualization and treatment. After the localization of tumors bearing somatostatin receptors with 111In or 99mTc labeled somatostatin analogues, in the case of high tumor uptake related to non target tissues, different radioisotopes have been used for their treatment. Thus, application of high doses of 111In- DTPA-octreotide had an impact on improvement of the clinical symptoms, without significant reduction of the tumor mass. However, 90Y somatostatin analogues (DOTA TOC, lanreotide) may be more effective for reduction of the tissue of the larger tumors while 177Lu labeled ones may be applied in smaller tumors. Combination of both of them seems to be the most effective therapy, particularly in tumors bearing both small and large lesions. The aim of this work is presentation of the preliminary results of the therapy of NETs with another octreotide analogue, 90Y DOTA TATE, which so far has been proved to have high therapeutic potential when labeled with 177Lu. Patients and methods: We investigated 7 patients with neuroendocrine tumors (two patients had neuroendocrine pancreatic carcinomas with liver metastases (one of them had metastases in peritoneal lymph nodes), one patient with operated (resected) bronchial carcinoid and liver metastases, three patients with neuroendocrine carcinomas of unknown origin and hepatic metastases (one with skeletal metastases) and one with pancreatic gastrinoma without metastases (surgery was impossible to perform). In all of them, together with other laboratory analyses and imaging methods, scintigraphy with somatostatin analogues was performed (in 3 with 111In Octreoscan and in the other 4 with 99mTc HYNIC TOC) and high tumor uptake was observed. The therapy was performed with 2- 4,5 GBq 90Y DOTA TATE per

Physical simulations using centrifuge techniques

International Nuclear Information System (INIS)

Sutherland, H.J.

1981-01-01

Centrifuge techniques offer a technique for doing physical simulations of the long-term mechanical response of deep ocean sediment to the emplacement of waste canisters and to the temperature gradients generated by them. Preliminary investigations of the scaling laws for pertinent phenomena indicate that the time scaling will be consistent among them and equal to the scaling factor squared. This result implies that this technique will permit accelerated-life-testing of proposed configurations; i.e, long-term studies may be done in relatively short times. Presently, existing centrifuges are being modified to permit scale model testing. This testing will start next year

Dispersion modeling by kinematic simulation: Cloud dispersion model

International Nuclear Information System (INIS)

Fung, J C H; Perkins, R J

2008-01-01

A new technique has been developed to compute mean and fluctuating concentrations in complex turbulent flows (tidal current near a coast and deep ocean). An initial distribution of material is discretized into any small clouds which are advected by a combination of the mean flow and large scale turbulence. The turbulence can be simulated either by kinematic simulation (KS) or direct numerical simulation. The clouds also diffuse relative to their centroids; the statistics for this are obtained from a separate calculation of the growth of individual clouds in small scale turbulence, generated by KS. The ensemble of discrete clouds is periodically re-discretized, to limit the size of the small clouds and prevent overlapping. The model is illustrated with simulations of dispersion in uniform flow, and the results are compared with analytic, steady state solutions. The aim of this study is to understand how pollutants disperses in a turbulent flow through a numerical simulation of fluid particle motion in a random flow field generated by Fourier modes. Although this homogeneous turbulent is rather a 'simple' flow, it represents a building block toward understanding pollutant dispersion in more complex flow. The results presented here are preliminary in nature, but we expect that similar qualitative results should be observed in a genuine turbulent flow.

Measurement of pressure ridges in SAR images of sea ice - Preliminary results on scattering theory

Science.gov (United States)

Vesecky, J. F.; Smith, M. P.; Daida, J. M.; Samadani, R.; Camiso, J. C.

1992-01-01

Sea ice ridges and keels (hummocks and bummocks) are important in sea ice research for both scientific and practical reasons. A long-term objective is to make quantitative measurements of sea ice ridges using synthetic aperture radar (SAR) images. The preliminary results of a scattering model for sea ice ridge are reported. The approach is through the ridge height variance spectrum Psi(K), where K is the spatial wavenumber, and the two-scale scattering model. The height spectrum model is constructed to mimic height statistics observed with an airborne optical laser. The spectrum model is used to drive a two-scale scattering model. Model results for ridges observed at C- and X-band yield normalized radar cross sections that are 10 to 15 dB larger than the observed cross sections of multiyear ice over the range of angles of incidence from 10 to 70 deg.

Cross-cultural aspects of ICT use by older people: preliminary results of a four-country ethnographical study

DEFF Research Database (Denmark)

Blat, Josep; Sayago, Sergio; Kälviäinen, Mirja

2011-01-01

addresses this issue by drawing on an ethnographical study of ICT use conducted with over 120 people, aged 67-71, in four European countries: Finland, Denmark, Italy and Spain, over a 6-month period. The preliminary results show that making a social, independent and worth use of ICT are common aspects...... across the four countries, despite the so-called heterogeneity of older people as ICT users. This short paper also touches on two key aspects which emerged from the study, engaging older people in research and the evolution of some barriers to technology use....

Simulation and beam line experiments for the superconducting ECR ion source VENUS

International Nuclear Information System (INIS)

Todd, Damon S.; Leitner, Daniela; Grote, David P.; Lyneis, ClaudeM.

2007-01-01

The particle-in-cell code Warp has been enhanced to incorporate both two- and three-dimensional sheath extraction models giving Warp the capability of simulating entire ion beam transport systems including the extraction of beams from plasma sources. In this article we describe a method of producing initial ion distributions for plasma extraction simulations in electron cyclotron resonance (ECR) ion sources based on experimentally measured sputtering on the source biased disc. Using this initialization method, we present preliminary results for extraction and transport simulations of an oxygen beam and compare them with experimental beam imaging on a quartz viewing plate for the superconducting ECR ion source VENUS

Preliminary Geological Findings on the BP-1 Simulant

Science.gov (United States)

Stoeser, D. B.; Rickman, D. L.; Wilson, S.

2010-01-01

A waste material from an aggregate producing quarry has been used to make an inexpensive lunar simulant called BP-1. The feedstock is the Black Point lava flow in northern Arizona. Although this is part of the San Francisco volcanic field, which is also the source of the JSC-1 series feedstock, BP-1 and JSC-1 are distinct. Chemically, the Black Point flow is an amygdaloidal nepheline-bearing basalt. The amygdules are filled with secondary minerals containing opaline silica, calcium carbonate, and ferric iron minerals. X-ray diffraction (XRD) detected approximately 3% quartz, which is in line with tests done by the Kennedy Space Center Industrial Hygiene Office. Users of this material should use appropriate protective equipment. XRD also showed the presence of significant halite and some bassanite. Both are interpreted to be evaporative residues due to recycling of wash water at the quarry. The size distribution of BP-1 may be superior to some other simulants for some applications.