WorldWideScience

Sample records for preliminary electro-optic evaluation

  1. Electro-optics laboratory evaluation: Deutsch optical waveguide connectors

    Science.gov (United States)

    1980-01-01

    A description of a test program evaluating the performance of an optical waveguide connector system is presented. Both quality and effectiveness of connections made in an optical fiber, performance of the equipment used and applicability of equipment and components to field conditions are reviewed.

  2. Missile Electro-Optical Countermeasures Simulation Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — This laboratory comprises several hardware-in-the-loop missile flight simulations designed specifically to evaluate the effectiveness of electro-optical air defense...

  3. EVALUATION METHOD FOR PARASITIC EFFECTS OF THE ELECTRO-OPTICAL MODULATOR IN A FIBER OPTIC GYROSCOPE

    Directory of Open Access Journals (Sweden)

    S. A. Volkovskiy

    2016-09-01

    Full Text Available Subject of Research.The paper proposes an original method for studying the parasitic effects in the electro-optic modulator of the fiber optic gyroscope. Proposed method is based on the usage of a special waveform phase modulation signal. Method. The essence of the proposed method lies in modification of serrodyne modulation signal, thereby providing a periodic displacement of the phase difference signal to the maximum of the interference curve. In this case, the intensity level reflects the influence of parasitic effects with the degree of manifestation being determined by the sequence of voltage control signals applied to the modulator. Enumeration of combinations of control signals and the corresponding intensity levels gives the possibility to observe an empirical dependence of the parasitic effects and use it later for compensation. Main Results. The efficiency of the proposed method is demonstrated by the program model of the fiber optic gyroscope. The results of the method application on a production sample of the device were obtained. Comparison with the results of direct estimate of the parasitic intensity modulation effect testifies to the effectiveness of the proposed method. Practical Relevance. The method can be used as a diagnostic tool to quantify the influence of parasitic effects in the electro-optic modulator of the fiber optic gyroscope as well as for their subsequent compensation.

  4. Evaluations on aero-optic effects of subsonic airborne electro-optical system

    Institute of Scientific and Technical Information of China (English)

    Kexin Yin; Huilin Jiang

    2006-01-01

    @@ A simple method based on CFD code and Matlab for aero-optic effects is presented. Density fluctuation from CFD code due to the changes of such factors as altitude, speed, equipment location, and wavelength is introduced as an input to Matlab. The overall calculations are in Matlab. The results show that the performance of electro-optical (EO) system can be improved when the altitude increasing, the speed is as slowly as possible, and the equipment location moves to the leading edge of the airborne platform as far as possible, for the wavelength there is an optimum one when the indexes of contrast and resolution of the system are both considered. All of these methods can minimize the optical aberrations. Several numerical simulations demonstrate the method.

  5. Imaging quality evaluation method of pixel coupled electro-optical imaging system

    Science.gov (United States)

    He, Xu; Yuan, Li; Jin, Chunqi; Zhang, Xiaohui

    2017-09-01

    With advancements in high-resolution imaging optical fiber bundle fabrication technology, traditional photoelectric imaging system have become ;flexible; with greatly reduced volume and weight. However, traditional image quality evaluation models are limited by the coupling discrete sampling effect of fiber-optic image bundles and charge-coupled device (CCD) pixels. This limitation substantially complicates the design, optimization, assembly, and evaluation image quality of the coupled discrete sampling imaging system. Based on the transfer process of grayscale cosine distribution optical signal in the fiber-optic image bundle and CCD, a mathematical model of coupled modulation transfer function (coupled-MTF) is established. This model can be used as a basis for following studies on the convergence and periodically oscillating characteristics of the function. We also propose the concept of the average coupled-MTF, which is consistent with the definition of traditional MTF. Based on this concept, the relationships among core distance, core layer radius, and average coupled-MTF are investigated.

  6. Electro-Optic System Development Lab

    Data.gov (United States)

    Federal Laboratory Consortium — The Electro-Optic System Development Lab serves as a development facility for electro-optical systems ranging from visible through long wave infrared. Capabilities...

  7. Embodiment of Learning in Electro-Optical Signal Processors

    Science.gov (United States)

    Hermans, Michiel; Antonik, Piotr; Haelterman, Marc; Massar, Serge

    2016-09-01

    Delay-coupled electro-optical systems have received much attention for their dynamical properties and their potential use in signal processing. In particular it has recently been demonstrated, using the artificial intelligence algorithm known as reservoir computing, that photonic implementations of such systems solve complex tasks such as speech recognition. Here we show how the backpropagation algorithm can be physically implemented on the same electro-optical delay-coupled architecture used for computation with only minor changes to the original design. We find that, compared when the backpropagation algorithm is not used, the error rate of the resulting computing device, evaluated on three benchmark tasks, decreases considerably. This demonstrates that electro-optical analog computers can embody a large part of their own training process, allowing them to be applied to new, more difficult tasks.

  8. Electro-Optics/Low Observables Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — The Electro-Optics/Low Observables Laboratory supports graduate instruction for students enrolled in the Low Observables program. Its purpose is to introduce these...

  9. Fiber Acousto-Electro-Optic Modulator

    Institute of Scientific and Technical Information of China (English)

    Anen; Jiang

    2003-01-01

    A new kind of fiber acousto-electro-optic modulator is made by using Lithium Niobate crystal. This kind of modulator can be used in fiber communication, and its center frequency can be changed by directed current voltages.

  10. A norbornene polymer brush for electro-optic applications

    Energy Technology Data Exchange (ETDEWEB)

    Jia, Yue; Spring, Andrew M.; Yu, Feng; Yamamoto, Kazuhiro [Institute for Materials Chemistry and Engineering, Kyushu University, 6–1 Kasuga Fukuoka 816–8580 (Japan); Aoki, Isao; Otomo, Akira [National Institute of Information and Communications Technology, 588–2 Iwaoka, Nishi-ku, Kobe 651–2492 (Japan); Yokoyama, Shiyoshi, E-mail: s_yokoyama@cm.kyushu-u.ac.jp [Institute for Materials Chemistry and Engineering, Kyushu University, 6–1 Kasuga Fukuoka 816–8580 (Japan)

    2014-03-03

    Norbornene-dicarboximide derived polymer brushes containing Disperse Red 1 appended chromophores have been prepared by sequencial ring opening metathesis polymerization and atom transfer radical polymerization. This brush was then employed as an electro-optic polymer host for high molecular hyperpolarizability phenyl vinylene thiophene vinylene (FTC) bridge chromophores in a binary chromophore system. The r{sub 33} of the polymer brush/bi-chromophore network was evaluated via in situ poling and was measured as 94 pm/V compared to the benchmark polymethylmethacrylate (PMMA) system of 76 pm/V with an identical chromophore. Furthermore, our polymer brush/bi-chromophore network exhibited an enhanced poling efficiency of 1.37 (nm/V){sup 2} as compared to a simple PMMA - FTC host - guest 0.70 (nm/V){sup 2}. - Highlights: • Synthesis of a norbornene polymer brush. • Use of this polymer brush as a host for electro-optic materials. • The polymer brush enables a large electro-optic coefficient r{sub 33}.

  11. The Electro-Optic Beam Position Monitor

    CERN Document Server

    Doherty, James

    2013-01-01

    This reports outlines the development of a new ultra-wideband electro-optic beam position monitor (EO-BPM) for use in the Large Hadron Collider (LHC) which utilises birefringent crystals and the Pockels effect to monitor beam position. The physical principles behind the operation of the device and tested topology, which incorporates two Lithium Tantalate crystals, is discussed.

  12. Basic electro-optics for electrical engineers

    CERN Document Server

    Boreman, Glenn D

    1999-01-01

    This text introduces imaging, radiometry, sources, detectors, and lasers, with special emphasis on flux-transfer issues. The first-order approach enables students to make back-of-the-envelope calculations needed for initial setup of optical apparatus. It is intended for students and newcomers to electro-optics.

  13. Quantum Modelling of Electro-Optic Modulators

    CERN Document Server

    Capmany, Jose

    2011-01-01

    Many components that are employed in quantum information and communication systems are well known photonic devices encountered in standard optical fiber communication systems, such as optical beamsplitters, waveguide couplers and junctions, electro-optic modulators and optical fiber links. The use of these photonic devices is becoming increasingly important especially in the context of their possible integration either in a specifically designed system or in an already deployed end-to-end fiber link. Whereas the behavior of these devices is well known under the classical regime, in some cases their operation under quantum conditions is less well understood. This paper reviews the salient features of the quantum scattering theory describing both the operation of the electro-optic phase and amplitude modulators in discrete and continuous-mode formalisms. This subject is timely and of importance in light of the increasing utilization of these devices in a variety of systems, including quantum key distribution an...

  14. Spherical Refractive Correction With an Electro-Optical Liquid Lens in a Double-Pass System

    Science.gov (United States)

    Sanàbria, F.; Díaz-Doutón, F.; Aldaba, M.; Pujol, J.

    2013-09-01

    In this study we show a novel double-pass configuration to correct the spherical refractive error by means of an electro-optical liquid lens.The proposed method enables spherical correction in the -12 D to +7 D range without movable parts using an electro-optical liquid lens.We have measured the optical performance of the spherical corrector in terms of power, pupil size and optical quality verifying that it fitsthe requirements to be applied to a double-pass system. We have also evaluated the performance of the proposed method in patients bycomparison with a conventional double-pass system using a Badal optometer.

  15. Electro-Optical Data Acquisition and Tracking System

    Data.gov (United States)

    Federal Laboratory Consortium — The Electro-Optical Data Acquisition and Tracking System (EDATS) dynamically tracks and measures target signatures. It consists of an instrumentation van integrated...

  16. Low Loss Electro-Optic Polymer Based Fast Adaptive Phase Shifters Realized in Silicon Nitride and Oxynitride Waveguide Technology

    Directory of Open Access Journals (Sweden)

    Lars Baudzus

    2016-08-01

    Full Text Available We present a comprehensive study on how to design and fabricate low loss electro-optic phase shifters based on an electro-optic polymer and the silicon nitride and silicon oxynitride waveguide material systems. The loss mechanisms of phase shifters with an electro-optic (EO polymer cladding are analyzed in detail and design solutions to achieve lowest losses are presented. In order to verify the low loss design a proof of concept prototype phase shifter was fabricated, which exhibits an attenuation of 0.8 dB/cm at 1550 nm and an electro-optic efficiency factor of 27%. Furthermore, the potential of this class of phase shifters is evaluated in numerical simulations, from which the optimal design parameters and achievable figures of merit were derived. The presented phase shifter design has its potential for application in fast adaptive multi stage devices for optical signal processing.

  17. Electro-optic imaging Fourier transform spectrometer

    Science.gov (United States)

    Chao, Tien-Hsin (Inventor); Znod, Hanying (Inventor)

    2009-01-01

    An Electro-Optic Imaging Fourier Transform Spectrometer (EOIFTS) for Hyperspectral Imaging is described. The EOIFTS includes an input polarizer, an output polarizer, and a plurality of birefringent phase elements. The relative orientations of the polarizers and birefringent phase elements can be changed mechanically or via a controller, using ferroelectric liquid crystals, to substantially measure the spectral Fourier components of light propagating through the EIOFTS. When achromatic switches are used as an integral part of the birefringent phase elements, the EIOFTS becomes suitable for broadband applications, with over 1 micron infrared bandwidth.

  18. Electro-optical detection of charged particles

    CERN Document Server

    Semertzidis, Y K; Kowalski, L A; Kraus, D E; Larsen, R; Lazarus, D M; Magurno, B; Nikas, D; Ozben, C; Srinivasan-Rao, T; Tsang, Thomas

    2000-01-01

    We have made the first observation of a charged particle beam by means of its electro-optical effect on the polarization of laser light in a LiNbO sub 3 crystal. The modulation of the laser light during the passage of a pulsed electron beam was observed using a fast photodiode and a digital oscilloscope. The fastest rise time measured, 120 ps, was obtained in the single shot mode and was limited by the bandwidth of the oscilloscope and the associated electronics. This technology holds good for detectors of greatly improved spatial and temporal resolution for single relativistic charged particles as well as particle beams.

  19. Electro-optics and lasers in Israel

    Science.gov (United States)

    Van Zwaren, Joesph

    1992-05-01

    With over 3,000 scientists, engineers, and technicians spread out in some 86 companies, and in 10 universities and research institutes, all within less than a 2 hour drive from one another, Israel has no doubt one of the largest concentrations of researchers and skilled manpower in electro-optics and lasers in the world. This report presents an up-to-date picture of the field in Israel, covering the industry, academia and education. The recent wave of Russian immigration is bringing thousands of scientists and tens of thousands of engineers and is expected to make an impact on the field of electro-optics and lasers. A million immigrants from Russia are expected to come between 1990 and 1995. There were 3,700 scientists and 2,800 engineers among the first 200,000 Soviet immigrants. As most of this qualified manpower can not be expected to be absorbed by the existing industry, the Israeli government is actively encouraging local and foreign investors and local and multinational companies to help develop new and expanded high-tech enterprises in Israel. The Ministry of Industry and Trade has embarked upon a broad ranged program for industrial growth and immigrant absorption with the goal of doubling technology-based exports in the next four years. The Ministry of Science and Technology has started a program supporting R&D projects at the different universities for immigrant scientists with the goal of capitalizing on the talents of the newcomers to strengthen academia.

  20. Future electro-optical sensors and processing in urban operations

    NARCIS (Netherlands)

    Grönwall, C.; Schwering, P.B.; Rantakokko, J.; Benoist, K.W.; Kemp, R.A.W.; Steinvall, O.; Letalick, D.; Björkert, S.

    2013-01-01

    In the electro-optical sensors and processing in urban operations (ESUO) study we pave the way for the European Defence Agency (EDA) group of Electro-Optics experts (IAP03) for a common understanding of the optimal distribution of processing functions between the different platforms. Combinations of

  1. An electro-optic waveform interconnect based on quantum interference

    CERN Document Server

    Qin, Li-Guo; Gong, Shang-Qing

    2016-01-01

    The ability to modulate an optical field via an electric field is regarded as a key function of electro-optic interconnects, which are used in optical communications and information processing systems. One of the main required devices for such interconnects is the electro-optic modulator (EOM). Current EOM based on the electro-optic effect and the electro-absorption effect often is bulky and power inefficient due to the weak electro-optic properties of its constituent materials. Here we propose a new mechanism to produce an arbitrary-waveform EOM based on the quantum interference, in which both the real and imaginary parts of the susceptibility are engineered coherently with the superhigh efficiency. Based on this EOM, a waveform interconnect from the voltage to the modulated optical absorption is realised. We expect that such a new type of electro-optic interconnect will have a broad range of applications including the optical communications and network.

  2. Electro-Optical System Simulation and Performance Prediction Extensions to EODES

    Science.gov (United States)

    2010-01-01

    performed a preliminary validation of the Streak Tube Imaging Lidar (STIL) model using data from an August 2001 field test of electro-optical imaging...situations. It was also determined that the long fall time (see Fig. 2) of the proposed photodetector did adversely impact image quality. These... Lidar (STIL) sensor showed good agreement between EODES simulations and actual sensor imagery. In addition, the image quality predicted by EODES

  3. Electro-optical techniques for signal conditioning

    Science.gov (United States)

    Helfrich, R. W.

    1981-01-01

    Electro-optical (EO) processing is discussed as a potential alternative to the all-digital approach to signal processing. Nonuniformity compensation can be done by normalizing all the single element detectors outputs in a staring array for both gain and level. Distortion correction can be accomplished with blackbodies, scene statistics or defocused optics. An algorithm used in digital signal conditioning that can be closely approximated by EO techniques is Local Area Brightness Control (LABC). In a digital processor, LABC is performed on a pixel-by-pixel basis, resulting in an enormous amount of calculation. A partially defocused optical system can be used in an EO analog to the digital system. For both nonuniformity compensation and LABC, the EO technique can result in great simplification.

  4. Hybrid Electro-Optically Modulated Microcombs

    CERN Document Server

    Del'Haye, Pascal; Diddams, Scott A

    2012-01-01

    Optical frequency combs based on mode-locked lasers have proven to be invaluable tools for a wide range of applications in precision spectroscopy and metrology. A novel principle of optical frequency comb generation in whispering-gallery mode microresonators ("microcombs") has been developed recently, which represents a promising route towards chip-level integration and out-of-the-lab use of these devices. Presently, two families of microcombs have been demonstrated: combs with electronically detectable mode spacing that can be directly stabilized, and broadband combs with up to octave-spanning spectra but mode spacings beyond electronic detection limits. However, it has not yet been possible to achieve these two key requirements simultaneously, as will be critical for most microcomb applications. Here we present a key step to overcome this problem by interleaving an electro-optic comb with the spectrum from a parametric microcomb. This allows, for the first time, direct control and stabilization of a microco...

  5. Passive electro optical materials and applications

    Science.gov (United States)

    Diekstall, K.; Gutu-Nelle, A.; Lauckner, J.; Lutz, F.; Mueller, S.; Seibold, G.; Schichl, H.; Volz, H.

    1980-12-01

    Electro-optical ceramics made of lead/lanthanum/zirconates/titanates (PLZT) can be economically manufactured by coprecipitation of the base materials and by vacuum sintering of the sintering of the green blocks. Magnesium additives reduce by half the operating voltage required to achieve an equal contrast ratio. Transparent electrodes deposited by sputtering tin-indium oxide remain transparent up to 2400 nm. The contrast ratio in the scattering mode amounts typically to 100 : 1 at 500 nm and 5 : 1 at 1000 nm, while in the birefrigence mode it amounts typically to 10,000 : 1 at 800 V/mm, at a thickness of 0.4 mm. Functional blocks were designed to demonstrate and test applications: a laser modular; a light intensity attenuator; welding protection goggles; and numerical displays. The first promising results with sputtered thin films indicate future suitability for displays. Multiple light modulators for opto-electronic nonimpact printing presently appear to be the most important application area.

  6. Photoinduced electro-optics measurements of biosilica transformation to cristobalite

    Energy Technology Data Exchange (ETDEWEB)

    Fuchs, Ido [Department of Chemistry and the Institute of Nanotechnology, Bar-Ilan University, Ramat-Gan 52900 (Israel); Aluma, Yaniv; Ilan, Micha [Department of Zoology, George S. Wise Faculty of Life Sciences, Tel Aviv University, Tel Aviv 6997801 (Israel); Kityk, Iwan [Institute of Electronic Systems, Faculty of Electrical Engineering, Czestochowa University, Czestochowa 42-201 (Poland); Mastai, Yitzhak, E-mail: Yitzhak.Mastai@biu.ac.il [Department of Chemistry and the Institute of Nanotechnology, Bar-Ilan University, Ramat-Gan 52900 (Israel)

    2015-03-15

    In this paper we studied the photoinduced electro optics effects in the thermal transformation process of biosilica to cristobalite, at a relatively low temperature and ambient pressure. This process was characterized by a variety of standards techniques with emphasis on linear electro optic effect measurements. Overall we demonstrated that photoinduced electro optics measurements are very sensitive to the transformation from amorphous structure of silica in the natural sponge samples to laminar string morphology of cristobalite. With this technique we could probe the change in the samples chirality from achiral bio silica to chiral cristobalite structure. Furthermore it is shown that natural biosilica have photoinduced linear electro optics respond indicating the chiral natural of biosilica. - Graphical abstract: The phase transformation of biosilica from marine sponges to Cristobalite under thermal treatment was investigated using photoinduced electro optics measurements. The figure shows the changes of the electro-optic coefficient of cristobalite and biosilica. - Highlights: • We examine phase transformation of biosilica. • We report transition from amorphous biosilica to crystalline Cristobalite. • Biosilica transformation to Cristobalite at temperature of 850 °C. • Biosilica transformation is studied with photoinduced measurements. • We examine changes in the photoinduced linear electro optics properties.

  7. Enhanced Kerr electro-optic nonlinearity through cascaded Pockels effects

    CERN Document Server

    Li, Guang-Zhen; Jiang, Hao-Wei; Chen, Xian-Feng

    2015-01-01

    We demonstrated a large enhancement of Kerr electro-optic nonlinearity through cascaded Pockels effects in a domain inversion ferroelectric crystal. We designed a structure that can implement the cascaded Pockels effects and second-harmonic generation simultaneously. The energy coupling between the fundamental lights of different polarizations led to a large nonlinear phase shift, and thus an effective electro-optic nonlinear refractive index. The effective nonlinearity can be either positive or negative, causing the second-harmonic spectra to move towards the coupling center, which in turn, offered us a way to measure the effective electro-optic nonlinear refractive index. The corresponding enhanced Kerr electro-optic nonlinearity is more than three orders of magnitude higher than the intrinsic value. These results open a door to manipulate the nonlinear phase by applying external electric field instead of light intensity in noncentrosymmetric crystals.

  8. Photoinduced electro-optics measurements of biosilica transformation to cristobalite

    Science.gov (United States)

    Fuchs, Ido; Aluma, Yaniv; Ilan, Micha; Kityk, Iwan; Mastai, Yitzhak

    2015-03-01

    In this paper we studied the photoinduced electro optics effects in the thermal transformation process of biosilica to cristobalite, at a relatively low temperature and ambient pressure. This process was characterized by a variety of standards techniques with emphasis on linear electro optic effect measurements. Overall we demonstrated that photoinduced electro optics measurements are very sensitive to the transformation from amorphous structure of silica in the natural sponge samples to laminar string morphology of cristobalite. With this technique we could probe the change in the samples chirality from achiral bio silica to chiral cristobalite structure. Furthermore it is shown that natural biosilica have photoinduced linear electro optics respond indicating the chiral natural of biosilica.

  9. Electro-Optic Imaging Fourier Transform Spectral Polarimeter Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Boulder Nonlinear Systems, Inc. (BNS) proposes to develop an Electro-Optic Imaging Fourier Transform Spectral Polarimeter (E-O IFTSP). The polarimetric system is...

  10. Electro-optic methods for longitudinal bunch diagnostics at FLASH

    Energy Technology Data Exchange (ETDEWEB)

    Steffen, B.R.

    2007-07-15

    Precise measurements of the temporal profile of sub-picosecond electron bunches are of high interest for the optimization and operation of VUV and X-ray free electron lasers. In this thesis, the shortest electro-optic signals measured so far for electron bunch diagnostics are presented, reaching a time resolution of better than 50 fs (rms). The e ects that introduce signal distortions and limit the time resolution are studied in numerical simulations for different electro-optic detection materials and techniques. The time resolution is mainly limited by lattice resonances of the electro-optic crystal. Electro-optic signals as short as 54 fs (rms) are obtained with gallium phosphide (GaP) crystals in a crossed polarizer detection scheme using temporally resolved electro-optic detection. Measuring near crossed polarization, where the electro-optic signal is proportional to the velocity field of the relativistic electron bunch, the shortest obtained signal width is 70 fs (rms). The electro-optic signals are compared to electron bunch shapes that are measured simultaneously with a transverse deflecting structure with 20 fs resolution. Numerical simulations using the bunch shapes as determined with the transverse deflecting cavity as input data are in excellent agreement with electro-optical signals obtained with GaP, both for temporally and spectrally resolved measurements. In the case of zinc telluride (ZnTe) the observed signals are slightly broader and significantly smaller than expected from simulations. These discrepancies are probably due to the poor optical quality of the available ZnTe crystals. (orig.)

  11. Terahertz wave electro-optic measurements with optical spectral filtering

    Energy Technology Data Exchange (ETDEWEB)

    Ilyakov, I. E., E-mail: igor-ilyakov@mail.ru; Shishkin, B. V. [Institute of Applied Physic RAS, Nizhny Novgorod 603950 (Russian Federation); Kitaeva, G. Kh. [Faculty of Physics, M.V. Lomonosov Moscow State University, Moscow 119991 (Russian Federation); Akhmedzhanov, R. A. [Institute of Applied Physic RAS, Nizhny Novgorod 603950 (Russian Federation); N.I. Lobachevsky State University of Nizhny Novgorod, Nizhny Novgorod 603950 (Russian Federation)

    2015-03-23

    We propose electro-optic detection techniques based on variations of the laser pulse spectrum induced during pulse co-propagation with terahertz wave radiation in a nonlinear crystal. Quantitative comparison with two other detection methods is made. Substantial improvement of the sensitivity compared to the standard electro-optic detection technique (at high frequencies) and to the previously shown technique based on laser pulse energy changes is demonstrated in experiment.

  12. Highly Sensitive Electro-Optic Modulators

    Energy Technology Data Exchange (ETDEWEB)

    DeVore, Peter S [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-10-26

    There are very important diagnostic and communication applications that receive faint electrical signals to be transmitted over long distances for capture. Optical links reduce bandwidth and distance restrictions of metal transmission lines; however, such signals are only weakly imprinted onto the optical carrier, resulting in low fidelity transmission. Increasing signal fidelity often necessitates insertion of radio-frequency (RF) amplifiers before the electro-optic modulator, but (especially at high frequencies) RF amplification results in large irreversible distortions. We have investigated the feasibility of a Sensitive and Linear Modulation by Optical Nonlinearity (SALMON) modulator to supersede RF-amplified modulators. SALMON uses cross-phase modulation, a manifestation of the Kerr effect, to enhance the modulation depth of an RF-modulated optical wave. This ultrafast process has the potential to result in less irreversible distortions as compared to a RF-amplified modulator due to the broadband nature of the Kerr effect. Here, we prove that a SALMON modulator is a feasible alternative to an RFamplified modulator, by demonstrating a sensitivity enhancement factor greater than 20 and significantly reduced distortion.

  13. Electro-optics of perovskite solar cells

    Science.gov (United States)

    Lin, Qianqian; Armin, Ardalan; Nagiri, Ravi Chandra Raju; Burn, Paul L.; Meredith, Paul

    2015-02-01

    Organohalide-perovskite solar cells have emerged as a leading next-generation photovoltaic technology. However, despite surging efficiencies, many questions remain unanswered regarding the mechanisms of operation. Here we report a detailed study of the electro-optics of efficient CH3NH3PbI3-perovskite-only planar devices. We report the dielectric constants over a large frequency range. Importantly, we found the real part of the static dielectric constant to be ∼70, from which we estimate the exciton-binding energy to be of order 2 meV, which strongly indicates a non-excitonic mechanism. Also, Jonscher's Law behaviour was consistent with the perovskite having ionic character. Accurate knowledge of the cell's optical constants allowed improved modelling and design, and using this information we fabricated an optimized device with an efficiency of 16.5%. The optimized devices have ∼100% spectrally flat internal quantum efficiencies and minimal bimolecular recombination. These findings establish systematic design rules to achieve silicon-like efficiencies in simple perovskite solar cells.

  14. Applications of lasers and electro-optics

    Science.gov (United States)

    Tan, B. C.; Low, K. S.; Chen, Y. H.; Ahmad, Harith; Tou, T. Y.

    Supported by the IRPA Programme on Laser Technology and Applications, many types of lasers have been designed, constructed and applied in various areas of science, medicine and industries. Amongst these lasers constructed were high power carbon dioxide lasers, rare gas halide excimer lasers, solid state Neodymium-YAG lasers, nitrogen lasers, flashlamp pumped dye lasers and nitrogen and excimer laser pumped dye lasers. These lasers and the associated electro-optics system, some with computer controlled, are designed and developed for the following areas of applications: (1) industrial applications of high power carbon dioxide lasers for making of i.c. components and other materials processing purposes -- prototype operational systems have been developed; (2) Medical applications of lasers for cancer treatment using the technique of photodynamic therapy -- a new and more effective treatment protocol has been proposed; (3) agricultural applications of lasers in palm oil and palm fruit-fluorescence diagnostic studies -- fruit ripeness signature has been developed and palm oil oxidation level were investigated; (4) development of atmospheric pollution monitoring systems using laser lidar techniques -- laboratory scale systems were developed; and (5) other applications of lasers including laser holographic and interferometric methods for the non destructive testing of materials.

  15. Recent Advances in the Design of Electro-Optic Sensors for Minimally Destructive Microwave Field Probing

    Directory of Open Access Journals (Sweden)

    John F. Whitaker

    2011-01-01

    Full Text Available In this paper we review recent design methodologies for fully dielectric electro-optic sensors that have applications in non-destructive evaluation (NDE of devices and materials that radiate, guide, or otherwise may be impacted by microwave fields. In many practical NDE situations, fiber-coupled-sensor configurations are preferred due to their advantages over free-space bulk sensors in terms of optical alignment, spatial resolution, and especially, a low degree of field invasiveness. We propose and review five distinct types of fiber-coupled electro-optic sensor probes. The design guidelines for each probe type and their performances in absolute electric-field measurements are compared and summarized.

  16. Strained silicon as a new electro-optic material

    DEFF Research Database (Denmark)

    Jacobsen, Rune Shim; Andersen, Karin Nordström; Borel, Peter Ingo

    2006-01-01

    of a silicon waveguide, and the induced nonlinear coefficient, (2) 15 pm V-1, makes it possible to realize a silicon electro-optic modulator. The strain-induced linear electro-optic effect may be used to remove a bottleneck5 in modern computers by replacing the electronic bus with a much faster optical...... processing and transmission could potentially be performed by all-silicon electronic and optical components. Here we have discovered that a significant linear electro-optic effect is induced in silicon by breaking the crystal symmetry. The symmetry is broken by depositing a straining layer on top...... functionalities can be integrated into monolithic components based on the versatile silicon platform, is due to the limited active optical properties of silicon3. Recently, however, a continuous-wave Raman silicon laser was demonstrated4; if an effective modulator could also be realized in silicon, data...

  17. Rational design of organic electro-optic materials

    CERN Document Server

    Dalton, L R

    2003-01-01

    Quantum mechanical calculations are used to optimize the molecular first hyperpolarizability of organic chromophores and statistical mechanical calculations are used to optimize the translation of molecular hyperpolarizability to macroscopic electro-optic activity (to values of greater than 100 pm V sup - sup 1 at telecommunications wavelengths). Macroscopic material architectures are implemented exploiting new concepts in nanoscale architectural engineering. Multi-chromophore-containing dendrimers and dendronized polymers not only permit optimization of electro-optic activity but also of auxiliary properties including optical loss (both absorption and scattering), thermal and photochemical stability and processability. New reactive ion etching and photolithographic techniques permit the fabrication of three-dimensional optical circuitry and the integration of that circuitry with semiconductor very-large-scale integration electronics and silica fibre optics. Electro-optic devices have been fabricated exploiti...

  18. Electro-optic architecture (EOA) for sensors and actuators in aircraft propulsion systems

    Science.gov (United States)

    Glomb, W. L., Jr.

    1989-06-01

    Results of a study to design an optimal architecture for electro-optical sensing and control in advanced aircraft and space systems are described. The propulsion full authority digital Electronic Engine Control (EEC) was the focus for the study. The recommended architecture is an on-engine EEC which contains electro-optic interface circuits for fiber-optic sensors on the engine. Size and weight are reduced by multiplexing arrays of functionally similar sensors on a pair of optical fibers to common electro-optical interfaces. The architecture contains common, multiplex interfaces to seven sensor groups: (1) self luminous sensors; (2) high temperatures; (3) low temperatures; (4) speeds and flows; (5) vibration; (6) pressures; and (7) mechanical positions. Nine distinct fiber-optic sensor types were found to provide these sensing functions: (1) continuous wave (CW) intensity modulators; (2) time division multiplexing (TDM) digital optic codeplates; (3) time division multiplexing (TDM) analog self-referenced sensors; (4) wavelength division multiplexing (WDM) digital optic code plates; (5) wavelength division multiplexing (WDM) analog self-referenced intensity modulators; (6) analog optical spectral shifters; (7) self-luminous bodies; (8) coherent optical interferometers; and (9) remote electrical sensors. The report includes the results of a trade study including engine sensor requirements, environment, the basic sensor types, and relevant evaluation criteria. These figures of merit for the candidate interface types were calculated from the data supplied by leading manufacturers of fiber-optic sensors.

  19. Building electro-optical systems making it all work

    CERN Document Server

    Hobbs, Philip C D

    2009-01-01

    Praise for the First Edition ""Now a new laboratory bible for optics researchers has joined the list: it is Phil Hobbs's Building Electro-Optical Systems: Making It All Work.""-Tony Siegman, Optics & Photonics News Building a modern electro-optical instrument may be the most interdisciplinary job in all of engineering. Be it a DVD player or a laboratory one-off, it involves physics, electrical engineering, optical engineering, and computer science interacting in complex ways. This book will help all kinds of technical people sort through the complexit

  20. Fast switchable electro-optic radial polarization retarder

    CERN Document Server

    Lim, B C; Lai, W J; Hong, M H

    2008-01-01

    A fast, switchable electro-optic radial polarization retarder (EO-RPR) fabricated using the electro-optic ceramic PMN-PT is presented. This EO-RPR is useful for fast, switchable generation of pure cylindrical vector beam. When used together with a pair of half-wave plates, the EO-RPR can change circularly polarized light into any cylindrical vector beam of interest such as radially or azimuthally polarized light. Radially and azimuthally polarized light with purities greater than 95% are generated experimentally. The advantages of using EO-RPR include fast response times, low driving voltage and transparency in a wide spectral range (500 -7000 nm).

  1. Electro-optical properties of tetragonal KNbO3

    Indian Academy of Sciences (India)

    P U Sastry

    2007-06-01

    Linear electro-optical tensor coefficients and optical susceptibility of tetragonal KNbO3 are calculated using a formalism based on bond charge theory. Results are in close agreement with the experimental data. The covalent Nb–O bonding network comprising the distorted NbO6 octahedral groups in the structure is found to be a major contributor to the electro-optic coefficients making these groups more sensitive to these properties than the KO12 groups. The orientations of the chemical bonds play an important role in determining these properties.

  2. External Electro-optic Sampling Utilizing an Asymmetric Fabry-Pérot Film of Poled Electro-optical Polymer

    Institute of Scientific and Technical Information of China (English)

    陈开鑫; 杨罕; 张大明; 张红波; 衣茂斌

    2001-01-01

    External electro-optic sampling has been first demonstrated using a poled electro-optical polymer asymmetricFabry-Pérot film, placed freely on the indium-tin oxide coplanar waveguide transmission line and used as anelectro-optic probe tip. Only one laser beam is required due to the fact that the asymmetric Fabry-Pérot film isutilized to convert the phase modulation to amplitude modulation. A 1.2 GHz microwave signal is sampled, andthe voltage sensitivity of about 2 m V/Hz is obtained. The results are promising for technical applications inhigh-speed electronic devices and monolithic microwave integrated circuits research.

  3. Application of electro-optic sampling in FEL diagnostics

    NARCIS (Netherlands)

    Yan, X.; MacLeod, A. M.; Gillespie, W. A.; Knippels, G.M.H.; Oepts, D.; van der Meer, A. F. G.

    2001-01-01

    The electro-optic sampling technique has been used for the full characterization (both amplitude and phase) of freely propagating pulsed electromagnetic radiation (such as FEL pulses, transition radiation) and for the quasistatic electric field of relativistic electron bunches. Measurements of the e

  4. Asymmetric Threat Assessment Using Electro-Optical Image Systems

    NARCIS (Netherlands)

    Schwering, P.B.W.; Schutte, K.

    2010-01-01

    Asymmetric threat assessment from military platforms, including early detection and classification by electro-optical means, is a complicated matter. These threats can be for instance explosives-packed rubber boats, minecarrying swimmers and divers in a marine environment or terrorists, improvised e

  5. Automatic Laser Glare Suppression in Electro-Optical Sensors

    Directory of Open Access Journals (Sweden)

    Gunnar Ritt

    2015-01-01

    Full Text Available Progress in laser technology has led to very compact but nevertheless powerful laser sources. In the visible and near infrared spectral region, lasers of any wavelength can be purchased. Continuous wave laser sources pose an especially serious threat to the human eye and electro-optical sensors due to their high proliferation and easy availability. The manifold of available wavelengths cannot be covered by conventional safety measures like absorption or interference filters. We present a protection concept for electro-optical sensors to suppress dazzling in the visible spectral region. The key element of the concept is the use of a digital micromirror device (DMD in combination with wavelength multiplexing. This approach allows selective spectral filtering in defined regions of interest in the scene. The system offers the possibility of automatic attenuation of dazzling laser radiation.

  6. Laser pulse spectral shaping based on electro-optic modulation

    Institute of Scientific and Technical Information of China (English)

    Yanhai Wang; Jiangfeng Wang; You'en Jiang; Yan Bao; Xuechun Li; Zunqi Lin

    2008-01-01

    A new spectrum shaping method, based on electro-optic modulation, to alleviate gain narrowing in chirped pulse amplification (CPA) system, is described and numerically simulated. Near-Fourier transform-limited seed laser pulse is chirped linearly through optical stretcher. Then the chirped laser pulse is coupled into integrated waveguide electro-optic modulator driven by an aperture-coupled-stripline (ACSL) electricalwaveform generator, and the pulse shape and amplitude are shaped in time domain. Because of the directrelationship between frequency interval and time interval of the linearly chirped pulse, the laser pulse spectrum is shaped correspondingly. Spectrum-shaping examples are modeled numerically to determine the spectral resolution of this technique. The phase error introduced in this method is also discussed.

  7. Electro-optic techniques in electron beam diagnostics

    Energy Technology Data Exchange (ETDEWEB)

    van Tilborg, Jeroen; Toth, Csaba; Matlis, Nicholas; Plateau, Guillaume; Leemans, Wim

    2011-06-17

    Electron accelerators such as laser wakefield accelerators, linear accelerators driving free electron lasers, or femto-sliced synchrotrons, are capable of producing femtosecond-long electron bunches. Single-shot characterization of the temporal charge profile is crucial for operation, optimization, and application of such accelerators. A variety of electro-optic sampling (EOS) techniques exists for the temporal analysis. In EOS, the field profile from the electron bunch (or the field profile from its coherent radiation) will be transferred onto a laser pulse co-propagating through an electro-optic crystal. This paper will address the most common EOS schemes and will list their advantages and limitations. Strong points that all techniques share are the ultra-short time resolution (tens of femtoseconds) and the single-shot capabilities. Besides introducing the theory behind EOS, data from various research groups is presented for each technique.

  8. Electro-optical switching of liquid crystals of graphene oxide

    Science.gov (United States)

    Song, Jang-Kun

    Electric field effects on aqueous graphene-oxide (GO) dispersions are reviewed in this chapter. In isotropic and biphasic regimes of GO dispersions, in which the inter-particle friction is low, GO particles sensitively respond to the application of electric field, producing field-induced optical birefringence. The electro-optical sensitivity dramatically decreases as the phase transits to the nematic phase; the increasing inter-particle friction hinders the rotational switching of GO particles. The corresponding Kerr coefficient reaches the maximum near the isotropic to biphasic transition concentration, at which the Kerr coefficient is found be c.a. 1:8 · 10-5 mV-2, the highest value ever reported in all Kerr materials. The exceptionally large Kerr effect arises from the Maxwell- Wagner polarization of GO particles with an extremely large aspect ratio and a thick electrical double layer (EDL). The polarization sensitively depends on the ratio of surface and bulk conductivities in dispersions. As a result, low ion concentration in bulk solvent is highly required to achieve a quality electro-optical switching in GO dispersions. Spontaneous vinylogous carboxylic reaction in GO particles produces H+ ions, resulting in spontaneous degradation of electro-optical response with time, hence the removal of residual ions by using a centrifuge cleaning process significantly improves the electro-optical sensitivity. GO particle size is another important parameter for the Kerr coefficient and the response time. The best performance is observed in a GO dispersion with c.a. 0.5 μm mean size. Dielectrophoretic migration of GO particles can be also used to manipulate GO particles in solution. Using these unique features of GO dispersions, one can fabricate GO liquid crystal devices similar to conventional liquid crystal displays; the large Kerr effect allows fabricating a low power device working at extremely low electric fields.

  9. Innovative, Inexpensive Etching Technique Developed for Polymer Electro- Optical Structures

    Science.gov (United States)

    Nguyen, Hung D.

    1999-01-01

    Electro-optic, polymer-based integrated optic devices for high-speed communication and computing applications offer potentially significant advantages over conventional inorganic electro-optic crystals. One key area of integrated optical technology--primary processing and fabrication--may particularly benefit from the use of polymer materials. However, as efforts concentrate on the miniaturization of electro-integrated circuit pattern geometries, the ability to etch fine features and smoothly sloped sidewalls is essential to make polymers useful for electro-integrated circuit applications. There are many existing processes available to etch polymer materials, but they all yield nearly vertical sidewalls. Vertical sidewalls are too difficult to reliably cover with a metal layer, and incomplete metalization degrades microwave performance, particularly at high frequency. However, obtaining a very sloped sidewall greatly improves the deposition of metal on the sidewall, leading to low-loss characteristics, which are essential to integrating these devices in highspeed electro-optic modulators. The NASA Lewis Research Center has developed in-house an inexpensive etching technique that uses a photolithography method followed by a simple, wet chemical etching process to etch through polymer layers. In addition to being simpler and inexpensive, this process can be used to fabricate smoothly sloped sidewalls by using a commercial none rodible mask: Spin-On-Glass. A commercial transparent material, Spin-On-Glass, uses processes and equipment similar to that for photoresist techniques.

  10. Electro-optic product design for manufacture: where next?

    Science.gov (United States)

    Barr, John R. M.; MacDonald, M.; Jeffery, G.; Troughton, M.

    2016-10-01

    Manufacturing of electro-optic products for military environments poses a large number of apparently intractable and mutually contradictory problems. The ability to successfully engage in this area presents an intellectual challenge of a high order. The Advanced Targeting Sector of Leonardo's Airborne and Space Systems Division, based in Edinburgh, has developed a successful range of electro-optic products and transitioned these into a volume, and high value, manufacturing environment. As products cycle through the design process, there has been strong feedback from users, suppliers, and most importantly from our manufacturing organization, that has driven evolution of our design practices. It is fair to say that recent pointer trackers and lasers bear little resemblance to those designed and built 10 years ago. Looking ahead, this process will only continue. There are interesting technologies that will drive improvements in manufacturability, reliability and usability of electro-optic products. Examples might include freeform optics, additive manufacture of metal components, and laser welding of optics to metals, to name but a few. These have uses across our product portfolio and, when sufficiently matured, will have a major impact on the product quality and reliability

  11. Polymer waveguide systems for nonlinear and electro-optic applications

    Science.gov (United States)

    Pantelis, Philip; Hill, Julian R.; Kashyap, Raman

    1991-12-01

    Waveguides with photochromic or electro-optic properties have been fabricated by a new technique using spin coating of polymers, or guest/host-polymer systems, on to grooves etched in an indium phosphide wafer. Monomoded waveguides at 633 nm, and at 1320 and 1550 nm (wavelengths of telecommunications interest) have been fabricated. These guides have good quality cleaved ends which allow efficient coupling of light from monomoded standard lensed silica fibers. An example of an electro-optic application is given in the form of a phase modulator. This device uses a side-chain polymer as the waveguide core that develops linear electro-optic properties following an electric field alignment process. It was found to have a switching voltage of 30 V, for a (pi) phase change, and had a total insertion loss of 9.4 dB. Waveguides with photochromic properties have also been produced using Aberchrome 670 (a commercially available fulgide) as a guest in a poly(methyl methacrylate) polymer host. Refractive index, optical loss, photochromic activity, and film forming properties of differing concentrations of guest (up to 20% concentration by weight) have been measured and are reported.

  12. Rational design of organic electro-optic materials

    Energy Technology Data Exchange (ETDEWEB)

    Dalton, L R [Departments of Chemistry and Electrical Engineering, University of Washington, Seattle, WA 98195-1700 (United States)

    2003-05-28

    Quantum mechanical calculations are used to optimize the molecular first hyperpolarizability of organic chromophores and statistical mechanical calculations are used to optimize the translation of molecular hyperpolarizability to macroscopic electro-optic activity (to values of greater than 100 pm V{sup -1} at telecommunications wavelengths). Macroscopic material architectures are implemented exploiting new concepts in nanoscale architectural engineering. Multi-chromophore-containing dendrimers and dendronized polymers not only permit optimization of electro-optic activity but also of auxiliary properties including optical loss (both absorption and scattering), thermal and photochemical stability and processability. New reactive ion etching and photolithographic techniques permit the fabrication of three-dimensional optical circuitry and the integration of that circuitry with semiconductor very-large-scale integration electronics and silica fibre optics. Electro-optic devices have been fabricated exploiting stripline, cascaded prism and microresonator device structures. Sub-1 V drive voltages and operational bandwidths of greater than 100 GHz have been demonstrated. Both single-and double-ring microresonators have been fabricated for applications such as active wavelength division multiplexing. Free spectral range values of 1 THz and per channel modulation bandwidths of 15 GHz have been realized permitting single-chip data rates of 500 Gb s{sup -1}. Other demonstrated devices include phased array radar, optical gyroscopes, acoustic spectrum analysers, ultrafast analog/digital converters and ultrahigh bandwidth signal generators. (topical review)

  13. Electro-optically actuated liquid-lens zoom

    Science.gov (United States)

    Pütsch, O.; Loosen, P.

    2012-06-01

    Progressive miniaturization and mass market orientation denote a challenge to the design of dynamic optical systems such as zoom-lenses. Two working principles can be identified: mechanical actuation and application of active optical components. Mechanical actuation changes the focal length of a zoom-lens system by varying the axial positions of optical elements. These systems are limited in speed and often require complex coupled movements. However, well established optical design approaches can be applied. In contrast, active optical components change their optical properties by varying their physical structure by means of applying external electric signals. An example are liquidlenses which vary their curvatures to change the refractive power. Zoom-lenses benefit from active optical components in two ways: first, no moveable structures are required and second, fast response characteristics can be realized. The precommercial development of zoom-lenses demands simplified and cost-effective system designs. However the number of efficient optical designs for electro-optically actuated zoom-lenses is limited. In this paper, the systematic development of an electro-optically actuated zoom-lens will be discussed. The application of aberration polynomials enables a better comprehension of the primary monochromatic aberrations at the lens elements during a change in magnification. This enables an enhanced synthesis of the system behavior and leads to a simplified zoom-lens design with no moving elements. The change of focal length is achieved only by varying curvatures of targeted integrated electro-optically actuated lenses.

  14. PREFACE: Colloidal and molecular electro-optics Colloidal and molecular electro-optics

    Science.gov (United States)

    Palberg, Thomas; Löwen, Hartmut

    2010-12-01

    The Kerr effect, also known as the quadratic electro-optic effect, was discovered more than a hundred years ago by John Kerr, a Scottish physicist [1]. It describes the change in the refractive index of a material in response to an applied electric field. Around 1950 its application swayed from simple to complex fluids. A strong contribution was made through a number of seminal papers by the French polymer scientist H Benoit [2-4]. These and others initiated wide interest from researchers working on macromolecular solutions or colloidal dispersions. Experimental activities were further boosted by the advent of the laser and theoretical approaches strongly drew from growing computer power. Use of AC or pulsed field techniques, as well as of inhomogeneous fields, including laser tweezers, studies of electrophoretic, dielectrophoretic, electro-osmotic and other types of motion by advanced optical methods and combinations with other external fields have had the greatest impact on our understanding of the electric field induced optical properties of soft matter systems. Today the field has matured and its techniques are broadly employed as versatile tools with applications ranging from biological systems to electronic ink. Fundamental interest still continues but more and more side branches have evolved fruitfully. This collection of papers was, therefore, brought together to take a fresh look at this traditional field. Further, we are to celebrate 35 years of a successful conference series, ELOPTO, with the last one held at Waldthausen Castle hosted by the Johannes Gutenberg University, MainzNote1 and the DFG Collaborative Research Centre TR6 'Physics of colloidal dispersions in external fields'Note2. In this issue we have collected the articles of some of the leading experts in the area, well garnished with novel approaches and clever ideas by younger colleagues. With our selection we hope to cover a representative spectrum of the ongoing research, catch the most

  15. Terrain-aided localization using electro-optical sensing (TALEOS)

    Science.gov (United States)

    Collins, Peter R. C.; Stephens, Arthur S.; Greenway, Phil; Deaves, Rob H.; Priestley, M. D. J.; Bullen, Mark

    1997-06-01

    The next generation of weapons systems will benefit from an array of new technologies which, when integrated, will provide the capability of accurately selecting the correct target. For example, target image features can be extracted from high resolution satellite data and this information can be fused with feature positions obtained from a weapon's imaging sensor. This will allow automatic target recognition to be performed. Terrain aided localization using electro-optical sensing (TALEOS) is a robust method of enhancing the performance of an imaging system through the exploitation of other sources of information. The primary image processing technique used in TALEOS is model-matching. The objective of model-matching is to discover the 3D position and orientation of an object (the model) with respect to the sensor reference frame by performing a match with corresponding features. In TALEOS, the model is derived from remotely sensed data and contains information about potentially observable features which might be extracted from the image. Embedded in this extended model is information about specific targets, including their known or estimated position, and features which characterize them. The Sowerby Research Center terrain model facility was used to gather realistic imagery. The terrain model is a 300:1 scale model of a 25 square kilometer area of real terrain. An overhead gantry system carries a video camera over the model enabling a wide variety of flight scenarios to be simulated experimentally. By a combination of special paint schemes and video inversion, pictures of the terrain model can provide a realistic simulation of infrared imagery. An image database was simulated using an overhead view of the model as if seen from a 'satellite' or reconnaissance aircraft. This imagery was utilized to evaluate the performance of the TALEOS technique for comparison with theoretical results. TALEOS integrates the data from the image processing subsystem with data from

  16. Characterization of the electro-optical transceivers in the KM3NeT optical network

    Directory of Open Access Journals (Sweden)

    Pulvirenti S.

    2016-01-01

    Full Text Available KM3NeT is a future research infrastructure hosting a network of neutrino telescopes in the abyss of the Mediterranean Sea. The whole data transport over an optical network is based on the Dense Wavelength Division Multiplexing technique with optical channels spaced 50 GHz apart and a bit rate of 1.25 Gbps. Over the telescope lifetime, precise temperature control of the laser is required to maintain stability of the central frequency, complying with the recommendations of the International Telecommunication Union. We will report on the characterisation of the tuneable features of the electro-optical transceivers required to compensate for the expected wavelength drift due to aging factors. Preliminary results will be showed.

  17. Photolithography by a tunable electro-optical lithium niobate phase array

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Photolithography experiments are performed by means of an optical phase mask with electrooptically tunable phase step.The phase mask consists of a 2-dimensional hexagonal lattice of inverted ferroelectric domains fabricated on a z-cut lithium niobate substrate. The electro-optically tunable phase step, between inverted domain, is obtained by the application of an external electric field along the z axis of the crystal via transparent electrodes. The collimated beam of an argon laser passes through the phase mask and the near field intensity patterns, at different planes of the Talbot length and for different values of the applied voltage, are used for photolithographic experiments. Preliminary results are shown and further applications are discussed.

  18. Weather and Atmospheric Effects on the Measurement and Use of Electro-Optical Signature Data

    Science.gov (United States)

    2017-02-01

    Atmospheric Effects on the Measurement and Use of Electro-Optical Signature Data RCC 469-17 February 2017 3 Table 1. General Sub- Region Terms of the...Atmospheric Effects on the Measurement and Use of Electro-Optical Signature Data RCC 469-17 February 2017 6 eye in all quantities. Multiple human eye ...on the Measurement and Use of Electro-Optical Signature Data RCC 469-17 February 2017 7 Table 4. Relative Spectral Response of the Eye λ

  19. Electro-optical properties of polymer stabilized cholesteric liquid crystal film

    Institute of Scientific and Technical Information of China (English)

    Ma Ji; Zheng Zhi-Gang; Liu Yong-Gang; Xuan Li

    2011-01-01

    Liquid crystals (LCs) and polymers are extensively used in various electro-optical applications. In this paper, normal mode polymer stabilized cholesteric LC film is prepared and studied. The effects of chiral dopant and monomer concentrations on the electro-optical properties, such as contrast ratio, driving voltage, hysteresis width and response time, are investigated. The reasons of electro-optical properties influenced by the concentrations of the materials are discussed. Through the proper material recipe, the electro-optical properties of polymer stabilized cholesteric LC film can be optimized.

  20. Development of in-orbit refocusing mechanism for SpaceEye-1 electro-optical payload

    Science.gov (United States)

    Lee, Minwoo; Kim, Jongun; Chang, Jin-Soo; Kang, Myung-Seok

    2016-09-01

    SpaceEye-1 earth observation satellite, developed by Satrec Initiative Co. Ltd., is a 300 kg scale spacecraft with high resolution electro-optical payload (EOS-D) which performs 1 m GSD, 12 km swath in low earth orbit. Metering structure of EOS-D is manufactured with Carbon Fiber Reinforced Plastic (CFRP). Due to the moisture emission from CFRP metering structure, this spaceborne electro-optical payload undergoes shrinkage after orbit insertion. The shrinkage of metering structure causes change of the distance between primary and secondary mirror. In order to compensate the moisture shrinkage effect, two types of thermal refocusing mechanism were developed, analyzed and applied to EOS-D. Thermal analysis simulating in-orbit thermal condition and thermo-elastic displacement analysis was conducted to calculate the performance of refocusing mechanism. For each EOS-D telescope, analytical refocusing range (displacement change between primary and secondary mirror) was 2.5 um and 3.6 um. Thus, the refocusing mechanism can compensate the dimensional instability of metering structure caused by moisture emission. Furthermore, modal, static and wavefront error analysis was conducted in order to evaluate natural frequency, structural stability and optical performance. As a result, it can be concluded that the refocusing system of EOS-D payload can perform its function in orbit.

  1. Electro-optical equivalent calibration technology for high-energy laser energy meters.

    Science.gov (United States)

    Wei, Ji Feng; Chang, Yan; Sun, Li Qun; Zhang, Kai; Hu, Xiao Yang; Zhang, Wei

    2016-04-01

    Electro-optical equivalent calibration with high calibration power and high equivalence is particularly well-suited to the calibration of high-energy laser energy meters. A large amount of energy is reserved during this process, however, which continues to radiate after power-off. This study measured the radiation efficiency of a halogen tungsten lamp during power-on and after power-off in order to calculate the total energy irradiated by a lamp until the high-energy laser energy meter reaches thermal equilibrium. A calibration system was designed based on the measurement results, and the calibration equivalence of the system was analyzed in detail. Results show that measurement precision is significantly affected by the absorption factor of the absorption chamber and by heat loss in the energy meter. Calibration precision is successfully improved by enhancing the equivalent power and reducing power-on time. The electro-optical equivalent calibration system, measurement uncertainty of which was evaluated as 2.4% (k = 2), was used to calibrate a graphite-cone-absorption-cavity absolute energy meter, yielding a calibration coefficient of 1.009 and measurement uncertainty of 3.5% (k = 2). A water-absorption-type high-energy laser energy meter with measurement uncertainty of 4.8% (k = 2) was considered the reference standard, and compared to the energy meter calibrated in this study, yielded a correction factor of 0.995 (standard deviation of 1.4%).

  2. Electro-optical equivalent calibration technology for high-energy laser energy meters

    Science.gov (United States)

    Wei, Ji Feng; Chang, Yan; Sun, Li Qun; Zhang, Kai; Hu, Xiao Yang; Zhang, Wei

    2016-04-01

    Electro-optical equivalent calibration with high calibration power and high equivalence is particularly well-suited to the calibration of high-energy laser energy meters. A large amount of energy is reserved during this process, however, which continues to radiate after power-off. This study measured the radiation efficiency of a halogen tungsten lamp during power-on and after power-off in order to calculate the total energy irradiated by a lamp until the high-energy laser energy meter reaches thermal equilibrium. A calibration system was designed based on the measurement results, and the calibration equivalence of the system was analyzed in detail. Results show that measurement precision is significantly affected by the absorption factor of the absorption chamber and by heat loss in the energy meter. Calibration precision is successfully improved by enhancing the equivalent power and reducing power-on time. The electro-optical equivalent calibration system, measurement uncertainty of which was evaluated as 2.4% (k = 2), was used to calibrate a graphite-cone-absorption-cavity absolute energy meter, yielding a calibration coefficient of 1.009 and measurement uncertainty of 3.5% (k = 2). A water-absorption-type high-energy laser energy meter with measurement uncertainty of 4.8% (k = 2) was considered the reference standard, and compared to the energy meter calibrated in this study, yielded a correction factor of 0.995 (standard deviation of 1.4%).

  3. Electro-optical study of the exposure of Azospirillum brasilense carbohydrate epitopes.

    Science.gov (United States)

    Guliy, Olga I; Matora, Larisa Yu; Dykman, Lev A; Staroverov, Sergey A; Burygin, Gennady L; Bunin, Viktor D; Burov, Andrei M; Ignatov, Oleg V

    2015-01-01

    The exposure of Azospirillum brasilense carbohydrate epitopes was investigated by electro-optical analysis of bacterial cell suspensions. To study changes in the electro-optical (EO) properties of the suspensions, we used antibodies generated to the complete lipopolysaccharide of A. brasilense type strain Sp7 and also antibodies to the smooth and rough O polysaccharides of Sp7. After 18 hr of culture growth, the EO signal of the suspension treated with antibodies to smooth O polysaccharide was approximately 20% lower than that of the suspension treated with antibodies to complete lipopolysaccharide (control). After 72 hr of culture growth, the strongest EO signal was observed for the cells treated with antibodies to rough O polysaccharide (approximately 46% greater than the control), whereas for the cells treated with antibodies to smooth O polysaccharide, it was much lower (approximately 23% of the control). These data were confirmed by electron microscopy. The results of the study may have importance for the rapid evaluation of changes in lipopolysaccharide form in microbial biotechnology, when the antigenic composition of the bacterial surface requires close control.

  4. Electro-optic analyzer of angular momentum hyperentanglement.

    Science.gov (United States)

    Wu, Ziwen; Chen, Lixiang

    2016-02-25

    Characterizing a high-dimensional entanglement is fundamental in quantum information applications. Here, we propose a theoretical scheme to analyze and characterize the angular momentum hyperentanglement that two photons are entangled simultaneously in spin and orbital angular momentum. Based on the electro-optic sampling with a proposed hyper-entanglement analyzer and the simple matrix operation using Cramer rule, our simulations show that it is possible to retrieve effectively both the information about the degree of polarization entanglement and the spiral spectrum of high-dimensional orbital angular momentum entanglement.

  5. Track Initiation for Electro-Optical Tracking of Space Objects

    Science.gov (United States)

    Xu, Z. W.; Wang, X.

    2016-03-01

    Aimed at the track initiation for the electro-optical tracking of space objects, and based on modified Hough transformation, a track initiation algorithm without prior information is proposed to realize the fully robotic identification and tracking of moving objects. The method is valid for the tracking of multi-target as well as with a non-continuous sequence. Simulation shows that the method is effective and applicable for operational usage, and is especially good for the search and discovery of new objects.

  6. Electro-optic probe measurements of electric fields in plasmas

    Science.gov (United States)

    Nishiura, M.; Yoshida, Z.; Mushiake, T.; Kawazura, Y.; Osawa, R.; Fujinami, K.; Yano, Y.; Saitoh, H.; Yamasaki, M.; Kashyap, A.; Takahashi, N.; Nakatsuka, M.; Fukuyama, A.

    2017-02-01

    The direct measurements of high-frequency electric fields in a plasma bring about significant advances in the physics and engineering of various waves. We have developed an electro-optic sensor system based on the Pockels effect. Since the signal is transmitted through an optical fiber, the system has high tolerance for electromagnetic noises. To demonstrate its applicability to plasma experiments, we report the first result of measurement of the ion-cyclotron wave excited in the RT-1 magnetosphere device. This study compares the results of experimental field measurements with simulation results of electric fields in plasmas.

  7. Electro-Optical Modulator Bias Control Using Bipolar Pulses

    Science.gov (United States)

    Farr, William; Kovalik, Joseph

    2007-01-01

    An improved method has been devised for controlling the DC bias applied to an electro-optical crystal that is part of a Mach-Zehnder modulator that generates low-duty-cycle optical pulses for a pulse-position modulation (PPM) optical data-communication system. In such a system, it is desirable to minimize the transmission of light during the intervals between pulses, and for this purpose, it is necessary to maximize the extinction ratio of the modulator (the ratio between the power transmitted during an "on" period and the power transmitted during an "off" period). The present method is related to prior dither error feedback methods, but unlike in those methods, there is no need for an auxiliary modulation subsystem to generate a dithering signal. Instead, as described below, dither is effected through alternation of the polarity of the modulation signal. The upper part of Figure 1 schematically depicts a Mach-Zehnder modulator. The signal applied to the electro-optical crystal consists of a radio-frequency modulating pulse signal, VRF, superimposed on a DC bias Vbias. Maximum extinction occurs during the off (VRF = 0) period if Vbias is set at a value that makes the two optical paths differ by an odd integer multiple of a half wavelength so that the beams traveling along the two paths interfere destructively at the output beam splitter. Assuming that the modulating pulse signal VRF has a rectangular waveform, maximum transmission occurs during the "on" period if the amplitude of VRF is set to a value, V , that shifts the length of the affected optical path by a half wavelength so that now the two beams interfere constructively at the output beam splitter. The modulating pulse signal is AC-coupled from an amplifier to the electro-optical crystal. Sometimes, two successive pulses occur so close in time that the operating point of the amplifier drifts, one result being that there is not enough time for the signal level to return to ground between pulses. Also, the

  8. Optimization Design Parameters of Electro-optic Modulators for Low Loss Wide Bandwidth Capability of Optical Communication Systems

    Directory of Open Access Journals (Sweden)

    Ahmed Nabih Zaki Rashed

    2012-06-01

    Full Text Available The effects of temperature, and operating signal wavelength on high frequency radio frequency transmission characteristics are deeply investigated against various materials based electro optic modulator devices such as lithium Niobate (LiNbO3, polymer, and semiconductor materials. On the other hand, we have developed the optimization of the electro optic modulator parameters where the effective index plays an essential role in the evaluation of the bandwidth structure. The effects of design parameters on the modulating voltage and optical bandwidth are also investigated for different materials based electro optic modulators by using rigorous transmission modeling techniques. The low loss wide bandwidth capability of optoelectronic systems makes them attractive for the transmission and processing of microwave signals, while the development of high capacity optical communication systems has required the use of modulation techniques in optical transmitters and receivers. This paper has presented the low loss wide bandwidth for different electrooptic modulators based on design of optimization parameters for high speed transmission performance.

  9. A novel electro-optical pump-probe system for bioelectromagnetic investigations

    Science.gov (United States)

    De Angelis, Annalisa; Couderc, Vincent; Leproux, Philippe; Labruyère, Alexis; Tonello, Alessandro; El Amari, Saad; Arnaud-Cormos, Delia; Leveque, Philippe

    2012-10-01

    In the area of bioelectromagnetic studies there is a growing interest to understand the mechanisms leading to nanosecond electric fields induced electroporation. Real-time imaging techniques at molecular level could probably bring further advances on how electric fields interact with living cells. However the investigations are limited by the present-day lack of these kinds of advanced instrumentations. In this context, we present an innovative electro-optical pump-probe system. The aim of our project is to provide a performing and compact device for electrical stimulation and multiplex Coherent anti-Stokes Raman Scattering (M-CARS) imaging of biological cells at once. The system consists of a 1064 nm sub-nanosecond laser source providing both a monochromatic pump and a polychromatic Stokes optical beam used in a CARS process, as well as the trigger beam for the optoelectronic switching-based electrical pulse generator. The polychromatic Stokes beam (from 600 to 1700 nm) results from a supercontinuum generation in a photonic crystal fiber (PCF). A detailed spectro-temporal characterization of such a broadband spectrum shows the impact of the nonlinear propagation in the fiber on the Stokes wave. Despite the temporal distortions observable on Stokes pulse profiles, their spectral synchronization with the pump pulse remains possible and efficient in the interesting region between 1100 nm and 1700 nm. The electrical stimulation device consists of a customized generator combining microstrip-line technology and laser-triggered photoconductive semiconductor switches. Our experimental characterization highlights the capability for such a generator to control the main pulse parameters (profile, amplitude and duration) and to be easily synchronized with the imaging system. We finally test and calibrate the system by means of a KDP crystal. The preliminary results suggest that this electro-optical system provides a suitable tool for real-time investigation of

  10. A new electro-optic waveguide architecture and the unprecedented devices it enables

    Science.gov (United States)

    Davis, Scott R.; Rommel, Scott D.; Farca, George; Anderson, Michael H.

    2008-04-01

    A new electro-optic waveguide platform, which provides unprecedented electro-optical phase delays (> 1mm), with very low loss (integrated photonic architecture has applications in a wide array of commercial and defense markets including: remote sensing, micro-LADAR, OCT, laser illumination, phased array radar, optical communications, etc. Performance attributes of several example devices are presented.

  11. Waveguide electro-optic modulators based on self-assembled material systems

    Institute of Scientific and Technical Information of China (English)

    LIU Zhi-fu; MA Jing; SUN De-gui; XU Guo-yang; HO Seng-Tiong; ZHU Pei-wang; KANG Hu; Antonio Facchetti; Tobin J. Marks

    2005-01-01

    Fabrication and characterization of electro-optic modulators based on the novel organic electro-optic materials composed of self-assembled superlattices (SAS) were presented, both wet-dipping self-assembly and vapor phase deposition approaches were discussed. Prototype waveguide electro-optic modulators were fabricated using SAS films integrated with low-loss polymeric materials functioning as partial guiding and cladding layers.Promising electro-optic thin film materials including DTPT and PEPCOOH grown from the vapor phase were used for fabrication and test of electro-optic prototype modulators. Finally,the EO coefficient of tens of pm/V was obtained,which can sufficiently support high-speed and small size EO modulators.

  12. Electro-optically tunable diffraction grating with photoaligned liquid crystals

    Science.gov (United States)

    Węgłowski, Rafał; Kozanecka-Szmigiel, Anna; Piecek, Wiktor; Konieczkowska, Jolanta; Schab-Balcerzak, Ewa

    2017-10-01

    This work shows the possibility of fabricating one- and two-dimensional diffraction structures based on liquid crystals photoaligned with the layers of photosensitive azobenzene poly(ester imide). The gratings involve a micron-sized planar-twisted nematic alignment. The diffraction efficiency of these gratings is controlled by a uniform electric field applied across the cell. The electro-optical measurements showed short switching times (0.8 ms and 7 ms for τrise and τdecay respectively) and low driving electric fields (1 . 5 V / μm) of 1st order diffracted light. The LC grating is regarded as an amplitude grating in the low electric field region and a phase grating in the high electric field region. Moreover the diffraction efficiency is polarization-independent in the wide range of external electric fields.

  13. Electro-optic effect and photoelastic effect of feroelectric relaxors

    Science.gov (United States)

    Takeda, Kotaro; Hoshina, Takuya; Takeda, Hiroaki; Tsurumi, Takaaki

    2016-10-01

    To understand the origin of the electro-optic effect (EO-effect) of ferroelectric relaxors, the relationships among the quadratic EO-coefficient, photoelastic coefficient, and electron density were elucidated. The quadratic EO-coefficient is given by the product of the photoelastic and electrostrictive coefficients. Materials consisting of heavy elements normally exhibit high refractive indices and large photoelastic effects, indicating that the photoelastic coefficient increases with electron density of materials. The photoelastic coefficient was calculated as a function of the electron density of materials. The equations derived in this study were experimentally confirmed using lanthanum-added lead-zirconate-titanate (PLZT) transparent ceramics. It was found that the origin of the EO-effect in ferroelectric relaxors was the photoelastic effect coupled with electric-field-induced strain via the piezoelectric and electrostrictive effects.

  14. Electro-optic Laser-Sampled Neutron Detector

    Energy Technology Data Exchange (ETDEWEB)

    J. Kenneth Shultis; Douglas McGregor

    2009-11-30

    A new method of detecting radiation which can allow for long distance measurements is being investigated. The device is primarily for neutrons detection althought it could, in principle, be used for gamma ray detection. The neutron detection medium is a solid, transparent, electro-optical material, such as lithium niobate, lithium tantalite, or barium borate. Crystals of these materials act as optical gates to laser light, allowing light to pass through only when a neutron interaction occurs in the crystal. Typical light detection devices, such as CCD cameras or photomultiplier tubes, can be used to signal when light passes through the crystal. The overall goal of the project is to investigate the feasibility of such devices for the detection of neutron radiation and to quantify their capabilities and limitations.

  15. Control Schemes for Driving Electro-optic Array Beam Deflectors

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The beam deflectors based on electro-optic phased array(EOPA) is mainly described, and then an analysis on existing control schemes for driving the EOPA beam deflectors, based on custom hard-wired electronics or based on software in a microcontroller, is made. Compared with these, a driving and control system for a multi-channel EOPA beam deflector is presented, in which the control assignment is implemented with a field programmable gate array(FPGA) chip. For different performance requirements, two control schemes, one with the serial scheme and another with the parallel scheme, have been explored and rapidly prototyped in Xilinx FPGA chips. With the control structures for the EOPA beam deflector, scanning rates of 588kHz and 5MHz can be respectively reached.

  16. Double-Teeth-Shaped Plasmonic Waveguide Electro-Optical Switches

    Institute of Scientific and Technical Information of China (English)

    ZHU Jia-Hu; HUANG Xu-Guang; MEI Xian

    2011-01-01

    @@ An electro-optical switch based on a plasmonic T-shaped waveguide structure with a double-teeth-shaped waveguide filled with 4-dimet4ylamino-N-methyl-4stilbazolium tosylate is proposed and numerically investigated.TheFinite-difference time domain simulation results reveal that the structure can operate as a circuit switch by controlling the external voltages V1 and/or V2.The proposed structure can also operate as a variable optical attenuator, which can continuously attenuate the power of a light beam from 6dB to 30dB by an external electrical field.The structure is of small size of a few hundred nanometers.Our results may open a possibility to construct nanoscale high-density photonic integration circuits.

  17. Electro-Optical Detection of Charged Particle Beams

    CERN Document Server

    Semertzidis, Y K; Kowalski, L A; Kraus, D E; Larsen, R C; Lazarus, D M; Magurno, B; Srinivasan-Rao, T; Tsang, Thomas; Usack, V

    1999-01-01

    We have made the first observation of a charged particle beam by means of its electro-optical effect on the propagation of laser light in a birefringent crystal at the Brookhaven National Laboratory Accelerator Test Facility. Polarized infrared light was coupled to a LiNbO3 crystal through a polarization maintaining fiber of 4 micron diameter. An electron beam in 10ps bunches of 1mm diameter was scanned across the crystal. The modulation of the laser light during passage of the electron beam was observed using a photodiode with 45GHz bandwidth. The fastest rise time measured, 120ps, was made in the single shot mode and was limited by the bandwidth of the oscilloscope and the associated electronics. Both polarization dependent and polarization independent effects were observed. This technology holds promise of greatly improved spatial and temporal resolution of charged particle beams.

  18. Design principles and realization of electro-optical circuit boards

    Science.gov (United States)

    Betschon, Felix; Lamprecht, Tobias; Halter, Markus; Beyer, Stefan; Peterson, Harry

    2013-02-01

    The manufacturing of electro-optical circuit boards (EOCB) is based to a large extent on established technologies. First products with embedded polymer waveguides are currently produced in series. The range of applications within the sensor and data communication markets is growing with the increasing maturity level. EOCBs require design flows, processes and techniques similar to existing printed circuit board (PCB) manufacturing and appropriate for optical signal transmission. A key aspect is the precise and automated assembly of active and passive optical components to the optical waveguides which has to be supported by the technology. The design flow is described after a short introduction into the build-up of EOCBs and the motivation for the usage of this technology within the different application fields. Basis for the design of EOCBs are the required optical signal transmission properties. Thereafter, the devices for the electro-optical conversion are chosen and the optical coupling approach is defined. Then, the planar optical elements (waveguides, splitters, couplers) are designed and simulated. This phase already requires co-design of the optical and electrical domain using novel design flows. The actual integration of an optical system into a PCB is shown in the last part. The optical layer is thereby laminated to the purely electrical PCB using a conventional PCB-lamination process to form the EOCB. The precise alignment of the various electrical and optical layers is thereby essential. Electrical vias are then generated, penetrating also the optical layer, to connect the individual electrical layers. Finally, the board has to be tested electrically and optically.

  19. Electro-optic and dynamic studies of biphenyl benzoate ferroelectric liquid crystals

    Energy Technology Data Exchange (ETDEWEB)

    Hemine, J., E-mail: hemine1@yahoo.f [Laboratoire de Physique de la Matiere Condensee, Universite Hassan II, Mohammedia-Casablanca, BP 146, F.S.T. Mohammedia (Morocco); Daoudi, A. [Universite Lille Nord de France, F-59000 Lille (France); ULCO, LDSMM, F-59140 Dunkerque (France); CNRS UMR8024, F-59140 Dunkerque (France); Legrand, C. [Universite Lille Nord de France, F-59000 Lille (France); ULCO, LEMCEL, F-62228 Calais (France); El kaaouachi, A.; Nafidi, A. [Laboratoire de Physique de la Matiere Condensee, Faculte des Sciences Ibnou Zohr, BP 28/S 80000 Agadir (Morocco); Ismaili, M.; Isaert, N. [Universite Lille Nord de France, F-59000 Lille (France); USTL, LDSMM, F-59655 Villeneuve d' Ascq (France); CNRS UMR8024, F-59655 Villeneuve d' Ascq (France); Nguyen, H.T. [Centre de Recherche Paul Pascal, Universite de Bordeaux 1, 33600 Pessac (France)

    2010-05-01

    We present electro-optic and dynamic properties on three homologous of biphenyl benzoate series of ferroelectric liquid crystals (FLCs) exhibiting the chiral smectic C phase (SmC*). The three compounds present high spontaneous polarization and show the SmC*-SmA*-N* phase sequence. Dielectric spectroscopy was used to provide the dynamics and dipolar ordering of the ferroelectric phase. The Goldstone relaxation mode was studied for sample cells on planar geometry without a DC bias voltage. The rotational viscosity corresponding to molecular motions in the SmC* phase was determined from dielectric measurements. The Arrhenius-type behavior of the rotational viscosity was found and the corresponding activation energies were evaluated.

  20. Selecting among competing models of electro-optic, infrared camera system range performance

    Science.gov (United States)

    Nichols, Jonathan M.; Hines, James E.; Nichols, James D.

    2013-01-01

    Range performance is often the key requirement around which electro-optical and infrared camera systems are designed. This work presents an objective framework for evaluating competing range performance models. Model selection based on the Akaike’s Information Criterion (AIC) is presented for the type of data collected during a typical human observer and target identification experiment. These methods are then demonstrated on observer responses to both visible and infrared imagery in which one of three maritime targets was placed at various ranges. We compare the performance of a number of different models, including those appearing previously in the literature. We conclude that our model-based approach offers substantial improvements over the traditional approach to inference, including increased precision and the ability to make predictions for some distances other than the specific set for which experimental trials were conducted.

  1. Simulation of electro-optical imaging system based on OpenGL

    Science.gov (United States)

    Zhu, Yong; Fu, Qiang; Duan, Jin; Jing, Wen-bo

    2013-08-01

    With the development of electro-optical imaging system technology and simulation technology, and the demand of optimizing the new type electro-optical imaging system theoretical model, more and more scientific research institutes, colleges and universities research on the simulation of electro-optical imaging system, and the better results were obtained. Simulation technology saved the cost of system design development, meanwhile, some complex and hard to re-implement experiments can be carried repeatedly. According to the demand of complex environment construction technology and the requirement of imaging simulation system fidelity, considering the performance of electro-optical imaging system, an electro-optical imaging system is modeled. The modeling has two aspects which is scene characteristic modeling and electro-optical system modeling. Scene characteristic modeling can construct dynamic scenes in different kinds of complex environments by using powerful OpenGL three-dimension model visualization technology. Electro-optical system modeling is consist of optical system and imaging detector. Electro-optical imaging system simulation model is established with the analysis of electro-optical imaging system theory. The use of modular design concept and general interface technology is combined. Different imaging effect is received under different parameters by modifying the model's related parameters. The experimental results show that, the image produced from simulation basically reflects the performance of imaging system, so this kind of image can be used as a information source for imaging system performance analysis. It provides a simple and feasible method for the analysis of imaging system performance, which has a very important practical significance.

  2. Shot noise reduced terahertz detection via spectrally post-filtered electro-optic sampling

    CERN Document Server

    Porer, Michael; Huber, Rupert

    2016-01-01

    In ultrabroadband terahertz electro-optic sampling, spectral filtering of the gate pulse can strongly reduce the quantum noise while the signal level is only weakly affected. The concept is tested for phase-matched electro-optic detection of field transients centered at 45 THz with 12-fs near-infrared gate pulses in AgGaS2. Our new approach increases the experimental signal-to-noise ratio by a factor of 3 compared to standard electro-optic sampling. Under certain conditions an improvement factor larger than 5 is predicted by our theoretical analysis.

  3. Measurement of the linear electro-optic coefficient of a minute cBN sample

    Institute of Scientific and Technical Information of China (English)

    DOU; Qingping; MA; Haitao; JIA; Gang; CHEN; Zhanguo; ZHANG

    2005-01-01

    Cubic boron nitride (Cbn) is a kind of artificial (synthetic) crystal. Transverse electro-optic modulation in a minute Cbn sample was carried out. Basing on the practical form of the crystal, we established the theoretical and experimental method according to the sample. For the first time, the linear electro-optic effect was observed in Cbn, and half-wave voltage of the Cbn sample was measured successfully. Furthermore, its linear electro-optic coefficient was calculated at 1.17×10-14 m/V.

  4. Fluorinated and Non-Fluorinated Electro-Optic Copolymers: Determination of the Time and Temperature Stability of the Induced Electro-Optic Coefficient

    Directory of Open Access Journals (Sweden)

    Alessandro Belardini

    2012-10-01

    Full Text Available Organic fluorinated materials demonstrate their excellent electro-optic properties and versatility for technological applications. The partial substitution of hydrogen with fluorine in carbon-halides bounds allows the reduction of absorption losses at the telecommunication wavelengths. In these interesting compounds, the electro-optic coefficient was typically induced by a poling procedure. The magnitude and the time stability of the coefficient is an important issue to be investigated in order to compare copolymer species. Here, a review of different measurement techniques (such as nonlinear ellipsometry, second harmonic generation, temperature scanning and isothermal relaxation was shown and applied to a variety of fluorinated and non-fluorinated electro-optic compounds.

  5. Future electro-optical sensors and processing in urban operations

    Science.gov (United States)

    Grönwall, Christina; Schwering, Piet B.; Rantakokko, Jouni; Benoist, Koen W.; Kemp, Rob A. W.; Steinvall, Ove; Letalick, Dietmar; Björkert, Stefan

    2013-10-01

    In the electro-optical sensors and processing in urban operations (ESUO) study we pave the way for the European Defence Agency (EDA) group of Electro-Optics experts (IAP03) for a common understanding of the optimal distribution of processing functions between the different platforms. Combinations of local, distributed and centralized processing are proposed. In this way one can match processing functionality to the required power, and available communication systems data rates, to obtain the desired reaction times. In the study, three priority scenarios were defined. For these scenarios, present-day and future sensors and signal processing technologies were studied. The priority scenarios were camp protection, patrol and house search. A method for analyzing information quality in single and multi-sensor systems has been applied. A method for estimating reaction times for transmission of data through the chain of command has been proposed and used. These methods are documented and can be used to modify scenarios, or be applied to other scenarios. Present day data processing is organized mainly locally. Very limited exchange of information with other platforms is present; this is performed mainly at a high information level. Main issues that arose from the analysis of present-day systems and methodology are the slow reaction time due to the limited field of view of present-day sensors and the lack of robust automated processing. Efficient handover schemes between wide and narrow field of view sensors may however reduce the delay times. The main effort in the study was in forecasting the signal processing of EO-sensors in the next ten to twenty years. Distributed processing is proposed between hand-held and vehicle based sensors. This can be accompanied by cloud processing on board several vehicles. Additionally, to perform sensor fusion on sensor data originating from different platforms, and making full use of UAV imagery, a combination of distributed and

  6. Electro-Optic Laser Scanners for Space-Based Lidar Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The purpose of this phase II SBIR is to design and build new non-mechanical, electro-optic (EO) laser scanners that will be suitable for space based laser ranging,...

  7. High Power Electro-Optic Modulator for Space-Based Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This Small Business Innovation Research Phase I effort will establish the feasibility of developing a fiber coupled, high power, electro-optically controlled, space...

  8. Electro-Optic Laser Scanners for Space-Based Lidar Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Vescent Photonics propose to design and build revolutionary non-mechanical, electro-optic (EO) laser scanners that will be suitable for space based laser ranging,...

  9. Structure Design of Polymer Electro-Optic Modulator with Ultra- Broadband

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Using finite element method, lots of calculating focusing on polymer electro-optic modulators with ultra-broadband were done, a few structures were analyzed. Coplanar waveguide electrode system was advanced, a few real examples was given.

  10. A Novel Electro-Optic Polymer Modulator Based on Long Period Fiber Gratings

    Institute of Scientific and Technical Information of China (English)

    Xiaowei Dong; Li Pei; Bin Li; Shui-sheng Jian

    2003-01-01

    A novel high-speed electro-optic (EO) polymer modulator based on long period gratings (LPG) is designed. Using the theory of multi-cladding optical waveguide, we achieved relationship between modulate voltage and LPG’s resonant wavelength.

  11. A Novel Electro-Optic Polymer Modulator Based on Long Period Fiber Gratings

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    A novel high-speed electro-optic (EO) polymer modulator based on long period gratings (LPG) is designed. Using the theory of multi-cladding optical waveguide, we achieved relationship between modulate voltage and LPG's resonant wavelength.

  12. Airborne Thematic Thermal InfraRed and Electro-Optical Imaging System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The innovation is an advanced Airborne Thematic Thermal InfraRed and Electro-Optical Imaging System (ATTIREOIS). ATTIREOIS sensor payload consists of two sets of...

  13. Tunable Optical Filters Having Electro-optic Whispering-gallery-mode Resonators

    Science.gov (United States)

    Savchenkov, Anatoliy (Inventor); Ilchenko, Vladimir (Inventor); Matsko, Andrey B. (Inventor); Maleki, Lutfollah (Inventor)

    2006-01-01

    Tunable optical filters using whispering-gallery-mode (WGM) optical resonators are described. The WGM optical resonator in a filter exhibits an electro-optical effect and hence is tunable by applying a control electrical signal.

  14. High Power Electro-Optic Modulator for Space-Based Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — ADVR, Inc. proposes the development of a fiber coupled, high power, electro-optically controlled, space qualified, phase modulator for the NASA Laser Interferometer...

  15. Electro-optic sampling of near-infrared waveforms

    Science.gov (United States)

    Keiber, Sabine; Sederberg, Shawn; Schwarz, Alexander; Trubetskov, Michael; Pervak, Volodymyr; Krausz, Ferenc; Karpowicz, Nicholas

    2016-03-01

    Access to the complete electric field evolution of a laser pulse is essential for attosecond science in general, and for the scrutiny and control of electron phenomena in solid-state physics specifically. Time-resolved field measurements are routine in the terahertz spectral range, using electro-optic sampling (EOS), photoconductive switches and field-induced second harmonic generation. EOS in particular features outstanding sensitivity and ease of use, making it the basis of time-resolved spectroscopic measurements for studying charge carrier dynamics and active optical devices. In this Letter, we show that careful optical filtering allows the bandwidth of this technique to be extended to wavelengths as short as 1.2 μm (230 THz) with half-cycle durations 2.3 times shorter than the sampling pulse. In a proof-of-principle application, we measure the influence of optical parametric amplification (OPA) on the electric field dynamics of a few-cycle near-infrared (NIR) pulse.

  16. Material optimization for electro-optic modulation and cascading

    Science.gov (United States)

    Reyes, Jorge; Darracq, Bruno; Canva, Michael; Blanchard-Desce, Mireille H.; Chaput, Frederic; Lahlil, Khalid; Boilot, Jean-Pierre; Brun, Alain; Levy, Yves

    2000-11-01

    A large effort has been devoted to the preparation of organic polymeric materials for electro-optic modulation and more recently for cascading based processes. These materials contain push-pull chromophores either incorporated as guest in a high Tg polymeric matrix (doped polymers) or grafted onto the polymeric matrix. These systems present several advantages but require significant improvement at the molecular level- by designing optimized chromophores with very large molecular figure of merit specific to each application targeted. The sol-gel route was used to prepare hybrid organic-inorganic materials, for the fabrication of amorphous solids of various shapes (bulk, think films...). The results obtained on optimized chromophore-doped poled thin films emphasize that intermolecular interactions have to be taken into account, as already pointed out by Dalton and coworkers. By combining a molecular engineering strategy for getting large molecular figure of merit and by controlling the intermolecular dipole-dipole interactions via both tuning the push-pull chromophore concentration and the incorporation screening carbazole moieties in high concentration. This strategy allows us to obtain a r33 of about 50 pm/V at 831 nm for a new optimized chromophore structure. In parallel, these thin films are being processed to be used as passive components for integrated optics.

  17. Optical and Electro-Optical Instrumentation (Guest Editorial

    Directory of Open Access Journals (Sweden)

    S. S. Negi

    2013-12-01

    Full Text Available Importance of Optical and Electro-Optical Instrumentation is growing by leaps and bounds in the modern day battlefield.  Night vision devices both image intensifier (II Tube based and thermal imagers (TIs are true force multipliers as they allow weapons and equipments to be used during day and night in fair and bad weather conditions. Growing trends in the thermal imaging area are mega pixels arrays with smaller pixel size, active and passive imaging at the focal plane, new detector materials operating at elevated temperature, dual color detectors, advanced signal and image processing, sensor and image fusion and automatic target recognition capability. With sufficient exploitations of these devices on ground, worldwide focus is towards the militarization of space by deploying multi / hyper spectral imagers for better target discrimination.  Low power non-lethal laser instrumentation is also emerging as another key area to fight a battle taking the shapes of Laser range finders, gap measuring devices, precision guided munitions, and laser proximity fuzes. The key trends in laser instrumentation area are eye-safe lasers, laser diodes arrays, diode pumped laser designators, high power lasers with  adaptive beam-shaping, sensor fuzed seekers and 3-D laser imaging.Defence Science Journal, 2013, 63(6, pp.543-544, DOI:http://dx.doi.org/10.14429/dsj.63.5746

  18. Electro-Optical Design for Efficient Visual Communication

    Science.gov (United States)

    Huck, Friedrich O.; Fales, Carl L.; Jobson, Daniel J.; Rahman, Zia-Ur

    1995-01-01

    Visual communication, in the form of telephotography and television, for example, can be regarded as efficient only if the amount of information that it conveys about the scene to the observer approaches the maximum possible and the associated cost approaches the minimum possible. Elsewhere we have addressed the problem of assessing the end to end performance of visual communication systems in terms of their efficiency in this sense by integrating the critical limiting factors that constrain image gathering into classical communications theory. We use this approach to assess the electro-optical design of image gathering devices as a function of the f number and apodization of the objective lens and the aperture size and sampling geometry of the phot-detection mechanism. Results show that an image gathering device that is designed to optimize information capacity performs similarly to the human eye. For both, the performance approaches the maximum possible, in terms of the efficiency with which the acquired information can be transmitted as decorrelated data, and the fidelity, sharpness, and clearity with which fine detail can be restored.

  19. Electro-Optical Imaging Fourier-Transform Spectrometer

    Science.gov (United States)

    Chao, Tien-Hsin; Zhou, Hanying

    2006-01-01

    An electro-optical (E-O) imaging Fourier-transform spectrometer (IFTS), now under development, is a prototype of improved imaging spectrometers to be used for hyperspectral imaging, especially in the infrared spectral region. Unlike both imaging and non-imaging traditional Fourier-transform spectrometers, the E-O IFTS does not contain any moving parts. Elimination of the moving parts and the associated actuator mechanisms and supporting structures would increase reliability while enabling reductions in size and mass, relative to traditional Fourier-transform spectrometers that offer equivalent capabilities. Elimination of moving parts would also eliminate the vibrations caused by the motions of those parts. Figure 1 schematically depicts a traditional Fourier-transform spectrometer, wherein a critical time delay is varied by translating one the mirrors of a Michelson interferometer. The time-dependent optical output is a periodic representation of the input spectrum. Data characterizing the input spectrum are generated through fast-Fourier-transform (FFT) post-processing of the output in conjunction with the varying time delay.

  20. A high average power electro-optic switch using KTP

    Energy Technology Data Exchange (ETDEWEB)

    Ebbers, C.A.; Cook, W.M.; Velsko, S.P.

    1994-04-01

    High damage threshold, high thermal conductivity, and small thermo-optic coefficients make KTiOPO{sub 4} (KTP) an attractive material for use in a high average power Q-switch. However, electro-chromic damage and refractive index homogeneity have prevented the utilization of KTP in such a device in the past. This work shows that electro-chromic damage is effectively suppressed using capacitive coupling, and a KTP crystal can be Q-switched for 1.5 {times} 10{sup 9} shots without any detectable electro-chromic damage. In addition, KTP with the high uniformity and large aperture size needed for a KTP electro-optic Q-switch can be obtained from flux crystals grown at constant temperature. A thermally compensated, dual crystal KTP Q-switch, which successfully produced 50 mJ pulses with a pulse width of 8 ns (FWHM), has been constructed. In addition, in off-line testing the Q-switch showed less than 7% depolarization at an average power loading of 3.2 kW/cm{sup 2}.

  1. Configuration of electro-optic fire source detection system

    Science.gov (United States)

    Fabian, Ram Z.; Steiner, Zeev; Hofman, Nir

    2007-04-01

    The recent fighting activities in various parts of the world have highlighted the need for accurate fire source detection on one hand and fast "sensor to shooter cycle" capabilities on the other. Both needs can be met by the SPOTLITE system which dramatically enhances the capability to rapidly engage hostile fire source with a minimum of casualties to friendly force and to innocent bystanders. Modular system design enable to meet each customer specific requirements and enable excellent future growth and upgrade potential. The design and built of a fire source detection system is governed by sets of requirements issued by the operators. This can be translated into the following design criteria: I) Long range, fast and accurate fire source detection capability. II) Different threat detection and classification capability. III) Threat investigation capability. IV) Fire source data distribution capability (Location, direction, video image, voice). V) Men portability. ) In order to meet these design criteria, an optimized concept was presented and exercised for the SPOTLITE system. Three major modular components were defined: I) Electro Optical Unit -Including FLIR camera, CCD camera, Laser Range Finder and Marker II) Electronic Unit -including system computer and electronic. III) Controller Station Unit - Including the HMI of the system. This article discusses the system's components definition and optimization processes, and also show how SPOTLITE designers successfully managed to introduce excellent solutions for other system parameters.

  2. Bandwidth enhancement of electro-optic field sensing using photonic down-mixing with harmonic sidebands.

    Science.gov (United States)

    Lee, Dong-Joon; Whitaker, John F

    2008-09-15

    We demonstrate that harmonic sidebands of an electro-optic modulator's driving frequency can be used as the local oscillator in a photonic down-mixing process in order to significantly enhance the bandwidth of near-field, electro-optic, microwave measurements. The creation of second- and third-order-harmonic modulation sidebands on a laser-diode output are described, with heterodyne down-conversion of microwave signals taking place within an electro-optic sensor crystal. The measurement bandwidth of an electro-optic microwave probe can thus be enhanced by as much as a factor of three with respect to the use of conventional, fundamental-harmonic sidebands. Carrier-sideband analysis from the measured optical spectrum indicates that millimeter-wave-frequency local-oscillator sidebands can be created using a Ku-band electro-optic modulator and that the electro-optic-signal-modulation depth can be enhanced by suppressing the light-beam carrier component. Transverse near-field distributions from high frequency patch antennas are extracted using both second- and third-order-harmonic sidebands.

  3. Internal model control of a fast steering mirror for electro-optical fine tracking

    Science.gov (United States)

    Xia, Yun-xia; Bao, Qi-liang; Wu, Qiong-yan

    2010-11-01

    The objective of this research is to develop advanced control methods to improve the bandwidth and tracking precision of the electro-optical fine tracking system using a fast steering mirror (FSM). FSM is the most important part in this control system. The model of FSM is established at the beginning of this paper. Compared with the electro-optical fine tracking system with ground based platform, the electro-optical fine tracking system with movement based platform must be a wide bandwidth and a robustness system. An advanced control method based on internal model control law is developed for electro-optical fine tracking system. The IMC is an advanced algorithm. Theoretically, it can eliminate disturbance completely and make sure output equals to input even there is model error. Moreover, it separates process to the system dynamic characteristic and the object perturbation. Compared with the PID controller, the controller is simpler and the parameter regulation is more convenient and the system is more robust. In addition, we design an improved structure based on classic IMC. The tracking error of the two-port control system is much better than which of the classic IMC. The simulation results indicate that the electro-optical control system based on the internal model control algorithm is very effective. It shows a better performance at the tracing precision and the disturbance suppresses. Thus a new method is provided for the high-performance electro-optical fine tracking system.

  4. Electro-optical approach to pavement deflection management

    Science.gov (United States)

    Rish, Jeff W., III; Adcock, Avery D.; Tuan, Christopher Y.; Baker, Samuel L.; Welker, Hugh W., II; Johnson, Roger F.

    1995-07-01

    A prototype continuous deflection device, referred to as a rolling weight deflectometer (RWD), has been developed as a nondestructive evaluation tool for airfield pavements. The system consists of a rigid trailer equipped with specially designed optical triangulation pavement sensors, a high-speed data acquisition system, and a high-pressure tire/load platform assembly. Pavement sensors are mounted on a rigid box beam equipped with an internal sensor system that corrects, in real time, the relative pavement height position measurements for displacements induced in the beam by mechanical vibrations, changes in temperature, or nonuniform dynamic loads at points where the beam attaches to the frame. The device produces continuous deflection profiles that show pavement response to a moving loaded wheel along the path of travel. These deflection profiles, combined with multiple passes along a lane, provide a far more detailed picture of the pavement structural integrity than has ever before been possible, because existing evaluation tools only produce response information at discrete points. Preliminary results show deflections measured by the RWD are in general agreement with the expected pavement response for various loads. A discussion of the device configuration, preliminary data, and potential as a pavement management tool is presented.

  5. Canopy induced aberration correction in airborne electro-optical imaging systems

    Science.gov (United States)

    Harder, James A.; Sprague, Michaelene W.

    2011-11-01

    An increasing number of electro-optical systems are being used by pilots in tactical aircraft. This means that the afore mentioned systems must operate through the aircrafts canopy, unfortunately the canopy functions as a less than ideal lens element in the electro-optical sensor optical path. The canopy serves first and foremost as an aircraft structural component, considerations like minimizing the drag co-efficient and the ability to survive bird strikes take precedence over achieving optimal optical characteristics. This paper describes how the authors characterized the optical characteristics of an aircraft canopy. Families of modulation transfer functions were generated, for various viewing geometries through the canopy and for various electro-optical system entrance pupil diameters. These functions provided us with the means to significantly reduce the effect of the canopy "lens" on the performance of a representative electro-optical system, using an Astigmatic Corrector Lens. A comparison of the electro-optical system performance with and without correction is also presented.

  6. Design and implementation of an electro-optical backplane with pluggable in-plane connectors

    Science.gov (United States)

    Pitwon, Richard C. A.; Hopkins, Ken; Wang, Kai; Selviah, David R.; Baghsiahi, Hadi; Offrein, Bert J.; Dangel, Roger; Horst, Folkert; Halter, Markus; Gmür, Max

    2010-02-01

    The design, implementation and characterisation of an electro-optical backplane and an active pluggable optical connector technology are presented. The connection architecture adopted allows line cards to mate and unmate from a passive electro-optical backplane with embedded polymeric waveguides. The active connectors incorporate photonics interfaces operating at 850 nm and a mechanism to passively align the interface to the embedded optical waveguides. A demonstration platform has been constructed to assess the viability of embedded electro-optical backplane technology in dense data storage systems. The electro-optical backplane is comprised of both copper layers and one polymeric optical layer, whereon waveguides have been patterned by a direct laser writing scheme. The optical waveguide design includes arrayed multimode waveguides with a pitch of 250 μm, multiple cascaded waveguide bends, non-orthogonal crossovers and in-plane connector interfaces. In addition, a novel passive alignment method has been employed to simplify high precision assembly of the optical receptacles on the backplane. The in-plane connector interface is based on a two lens free space coupling solution, which reduces susceptibility to contamination. The loss profiles of the complex optical waveguide layout has been characterised and successful transfer of 10.3 Gb/s data along multiple waveguides in the electro-optical backplane demonstrated.

  7. Modelling the Electro-Optic Properties of Liquid Crystals.

    Science.gov (United States)

    MacGregor, Alastair R.

    Available from UMI in association with The British Library. Requires signed TDF. Liquid crystals (LCs) have been recognised as a phase of matter intermediate between solid and liquid for about 100 years. During this time a large variety of mesophases have been discovered but it is only recently that their physics have begun to be understood. However if LCs are to continue to compete successfully in the displays market an improved understanding of their electro-optic properties must be gained. This thesis describes work carried out on two different types of LC: nematic and ferroelectric chiral smectic C (SmC^{*} ). In the former the molecules are orientationally ordered and randomly positioned while in the latter they are orientationally ordered and arranged in layers. The local mean molecular orientation is called the director and defines the uniaxial optic axis in both types of LC. In a nematic guest-host (NGH) LC an anisotropically absorbing dye is dissolved in the LC and the dye molecules align so that their maximum absorption axis is parallel to the director. When an electric field is applied to a cell containing NGHLC the molecules tend to rotate, because of their dielectric anisotropy, and alter the cell's transmittance. Previous attempts to model the change in optical transmittance with voltage have assumed that the LC and dye molecules are perfectly aligned with the director. In this work the disorder of the molecules about the director is taken into account and the overall agreement between theory and experiment is improved considerably. A method of calculating how the SmC^ {*} director configuration and layer orientation vary with voltage is presented. This method is tested by calculating the transmittance of a 7 mu m thick SmC^{* } LC cell for different azimuthal orientations of the cell between crossed polarisers. It is shown that the theoretical and measured orientations which give minimum transmittance are in good agreement. It is also shown that the

  8. Efficient single sideband microwave to optical conversion using an electro-optical whispering gallery mode resonator

    CERN Document Server

    Rueda, Alfredo; Collodo, Michele C; Vogl, Ulrich; Stiller, Birgit; Schunk, Gerhard; Strekalov, Dmitry V; Marquardt, Christoph; Fink, Johannes M; Painter, Oskar; Leuchs, Gerd; Schwefel, Harald G L

    2016-01-01

    Linking classical microwave electrical circuits to the optical telecommunication band is at the core of modern communication. Future quantum information networks will require coherent microwave-to-optical conversion to link electronic quantum processors and memories via low-loss optical telecommunication networks. Efficient conversion can be achieved with electro-optical modulators operating at the single microwave photon level. In the standard electro-optic modulation scheme this is impossible because both, up- and downconverted, sidebands are necessarily present. Here we demonstrate true single sideband up- or downconversion in a triply resonant whispering gallery mode resonator by explicitly addressing modes with asymmetric free spectral range. Compared to previous experiments, we show a three orders of magnitude improvement of the electro-optical conversion efficiency reaching 0.1% photon number conversion for a 10GHz microwave tone at 0.42mW of optical pump power. The presented scheme is fully compatible...

  9. Theory-Guided Design of Organic Electro-Optic Materials and Devices

    Directory of Open Access Journals (Sweden)

    Stephanie Benight

    2011-08-01

    Full Text Available Integrated (multi-scale quantum and statistical mechanical theoretical methods have guided the nano-engineering of controlled intermolecular electrostatic interactions for the dramatic improvement of acentric order and thus electro-optic activity of melt-processable organic polymer and dendrimer electro-optic materials. New measurement techniques have permitted quantitative determination of the molecular order parameters, lattice dimensionality, and nanoscale viscoelasticity properties of these new soft matter materials and have facilitated comparison of theoretically-predicted structures and thermodynamic properties with experimentally-defined structures and properties. New processing protocols have permitted further enhancement of material properties and have facilitated the fabrication of complex device structures. The integration of organic electro-optic materials into silicon photonic, plasmonic, and metamaterial device architectures has led to impressive new performance metrics for a variety of technological applications.

  10. A magneto-electro-optical effect in a plasmonic nanowire material

    Science.gov (United States)

    Valente, João; Ou, Jun-Yu; Plum, Eric; Youngs, Ian J.; Zheludev, Nikolay I.

    2015-01-01

    Electro- and magneto-optical phenomena play key roles in photonic technology enabling light modulators, optical data storage, sensors and numerous spectroscopic techniques. Optical effects, linear and quadratic in external electric and magnetic field are widely known and comprehensively studied. However, optical phenomena that depend on the simultaneous application of external electric and magnetic fields in conventional media are barely detectable and technologically insignificant. Here we report that a large reciprocal magneto-electro-optical effect can be observed in metamaterials. In an artificial chevron nanowire structure fabricated on an elastic nano-membrane, the Lorentz force drives reversible transmission changes on application of a fraction of a volt when the structure is placed in a fraction-of-tesla magnetic field. We show that magneto-electro-optical modulation can be driven to hundreds of thousands of cycles per second promising applications in magneto-electro-optical modulators and field sensors at nano-tesla levels. PMID:25906761

  11. Single-shot electro-optic sampling of coherent transition radiation at the A0 Photoinjector

    CERN Document Server

    Maxwell, T J; Piot, P; Thurman-Keup, R

    2012-01-01

    Future collider applications and present high-gradient laser plasma wakefield accelerators operating with picosecond bunch durations place a higher demand on the time resolution of bunch distribution diagnostics. This demand has led to significant advancements in the field of electro-optic sampling over the past ten years. These methods allow the probing of diagnostic light such as coherent transition radiation or the bunch wakefields with sub-picosecond time resolution. Potential applications in shot-to-shot, non-interceptive diagnostics continue to be pursued for live beam monitoring of collider and pump-probe experiments. Related to our developing work with electro-optic imaging, we present results on single-shot electro-optic sampling of the coherent transition radiation from bunches generated at the A0 photoinjector.

  12. Measurement of Sub-Picosecond Electron Bunches via Electro-Optic Sampling of Coherent Transition Radiation

    Energy Technology Data Exchange (ETDEWEB)

    Maxwell, Timothy John [Northern Illinois U.

    2012-01-01

    Future collider applications as well as present high-gradient laser plasma wakefield accelerators and free-electron lasers operating with picosecond bunch durations place a higher demand on the time resolution of bunch distribution diagnostics. This demand has led to significant advancements in the field of electro-optic sampling over the past ten years. These methods allow the probing of diagnostic light such as coherent transition radiation or the bunch wakefields with sub-picosecond time resolution. We present results on the single-shot electro-optic spectral decoding of coherent transition radiation from bunches generated at the Fermilab A0 photoinjector laboratory. A longitudinal double-pulse modulation of the electron beam is also realized by transverse beam masking followed by a transverse-to-longitudinal phase-space exchange beamline. Live profile tuning is demonstrated by upstream beam focusing in conjunction with downstream monitoring of single-shot electro-optic spectral decoding of the coherent transition radiation.

  13. Electro-optic dual-comb interferometry over 40-nm bandwidth

    CERN Document Server

    Duran, Vicente; Torres-Company, Victor

    2016-01-01

    Dual-comb interferometry is a measurement technique that uses two laser frequency combs to retrieve complex spectra in a line-by-line basis. This technique can be implemented with electro-optic frequency combs, offering intrinsic mutual coherence, high acquisition speed and flexible repetition-rate operation. A challenge with the operation of this kind of frequency comb in dual-comb interferometry is its limited optical bandwidth. Here, we use coherent spectral broadening and demonstrate electro-optic dual-comb interferometry over the entire telecommunications C band (200 lines covering ~ 40 nm, measured within 10 microseconds at 100 signal-to-noise ratio per spectral line). These results offer new prospects for electro-optic dual-comb interferometry as a suitable technology for high-speed broadband metrology, for example in optical coherence tomography or coherent Raman microscopy.

  14. Electro-Optical Imaging Microscopy of Dye-Doped Artificial Lipidic Membranes

    Science.gov (United States)

    Hajj, Bassam; De Reguardati, Sophie; Hugonin, Loïc; Le Pioufle, Bruno; Osaki, Toshihisa; Suzuki, Hiroaki; Takeuchi, Shoji; Mojzisova, Halina; Chauvat, Dominique; Zyss, Joseph

    2009-01-01

    Artificial lipidic bilayers are widely used as a model for the lipid matrix in biological cell membranes. We use the Pockels electro-optical effect to investigate the properties of an artificial lipidic membrane doped with nonlinear molecules in the outer layer. We report here what is believed to be the first electro-optical Pockels signal and image from such a membrane. The electro-optical dephasing distribution within the membrane is imaged and the signal is shown to be linear as a function of the applied voltage. A theoretical analysis taking into account the statistical orientation distribution of the inserted dye molecules allows us to estimate the doped membrane nonlinearity. Ongoing extensions of this work to living cell membranes are discussed. PMID:19948120

  15. Ultra-thin silicon/electro-optic polymer hybrid waveguide modulators

    Energy Technology Data Exchange (ETDEWEB)

    Qiu, Feng; Spring, Andrew M. [Institute for Materials Chemistry and Engineering, Kyushu University, 6-1 Kasuga-koen Kasuga, Fukuoka 816-8580 (Japan); Sato, Hiromu [Department of Molecular and Material Sciences, Kyushu University, 6-1 Kasuga-koen Kasuga, Fukuoka 816-8580 (Japan); Maeda, Daisuke; Ozawa, Masa-aki; Odoi, Keisuke [Nissan Chemical Industries, Ltd., 2-10-1 Tuboi Nishi, Funabashi, Chiba 274-8507 (Japan); Aoki, Isao; Otomo, Akira [National Institute of Information and Communications Technology, 588-2 Iwaoka, Nishi-ku, Kobe 651-2492 (Japan); Yokoyama, Shiyoshi, E-mail: s-yokoyama@cm.kyushu-u.ac.jp [Institute for Materials Chemistry and Engineering, Kyushu University, 6-1 Kasuga-koen Kasuga, Fukuoka 816-8580 (Japan); Department of Molecular and Material Sciences, Kyushu University, 6-1 Kasuga-koen Kasuga, Fukuoka 816-8580 (Japan)

    2015-09-21

    Ultra-thin silicon and electro-optic (EO) polymer hybrid waveguide modulators have been designed and fabricated. The waveguide consists of a silicon core with a thickness of 30 nm and a width of 2 μm. The cladding is an EO polymer. Optical mode calculation reveals that 55% of the optical field around the silicon extends into the EO polymer in the TE mode. A Mach-Zehnder interferometer (MZI) modulator was prepared using common coplanar electrodes. The measured half-wave voltage of the MZI with 7 μm spacing and 1.3 cm long electrodes is 4.6 V at 1550 nm. The evaluated EO coefficient is 70 pm/V, which is comparable to that of the bulk EO polymer film. Using ultra-thin silicon is beneficial in order to reduce the side-wall scattering loss, yielding a propagation loss of 4.0 dB/cm. We also investigated a mode converter which couples light from the hybrid EO waveguide into a strip silicon waveguide. The calculation indicates that the coupling loss between these two devices is small enough to exploit the potential fusion of a hybrid EO polymer modulator together with a silicon micro-photonics device.

  16. SCALE FACTOR DETERMINATION METHOD OF ELECTRO-OPTICAL MODULATOR IN FIBER-OPTIC GYROSCOPE

    Directory of Open Access Journals (Sweden)

    A. S. Aleynik

    2016-05-01

    Full Text Available Subject of Research. We propose a method for dynamic measurement of half-wave voltage of electro-optic modulator as part of a fiber optic gyroscope. Excluding the impact of the angular acceleration o​n measurement of the electro-optical coefficient is achieved through the use of homodyne demodulation method that allows a division of the Sagnac phase shift signal and an auxiliary signal for measuring the electro-optical coefficient in the frequency domain. Method. The method essence reduces to decomposition of step of digital serrodyne modulation in two parts with equal duration. The first part is used for quadrature modulation signals. The second part comprises samples of the auxiliary signal used to determine the value of the scale factor of the modulator. Modeling is done in standalone model, and as part of a general model of the gyroscope. The applicability of the proposed method is investigated as well as its qualitative and quantitative characteristics: absolute and relative accuracy of the electro-optic coefficient, the stability of the method to the effects of angular velocities and accelerations, method resistance to noise in actual devices. Main Results. The simulation has showed the ability to measure angular velocity changing under the influence of angular acceleration, acting on the device, and simultaneous measurement of electro-optical coefficient of the phase modulator without interference between these processes. Practical Relevance. Featured in the paper the ability to eliminate the influence of the angular acceleration on the measurement accuracy of the electro-optical coefficient of the phase modulator will allow implementing accurate measurement algorithms for fiber optic gyroscopes resistant to a significant acceleration in real devices.

  17. Unprecedented highest electro-optic coefficient of 226 pm/V for electro-optic polymer/TiO₂ multilayer slot waveguide modulators.

    Science.gov (United States)

    Jouane, Y; Chang, Y-C; Zhang, D; Luo, J; Jen, A K-Y; Enami, Y

    2014-11-03

    We investigated the electrical properties and optical quality of two layers a titanium dioxide (TiO₂) selective layer and a sol-gel silica cladding layer for use as coating layers for nonlinear optic (NLO) polymers in electro-optic (EO) polymer/TiO₂ multilayer slot waveguide modulators. We used a simple ellipsometric reflective technique developed by Teng and Man to measure the electro-optic (EO) coefficients of poled thin films of an EO polymer in an EO multilayer device. The Pockels coefficient was enhanced up to 226 and 198 pm/V at wavelengths of 1.31 and 1.55 μm, respectively, when optimally poled with TiO₂ and a sol-gel silica cladding.

  18. Electric field and temperature measurement using ultra wide bandwidth pigtailed electro-optic probes.

    Science.gov (United States)

    Bernier, Maxime; Gaborit, Gwenaël; Duvillaret, Lionel; Paupert, Alain; Lasserre, Jean-Louis

    2008-05-01

    We present pigtailed electro-optic probes that allow a simultaneous measurement of high frequency electric fields and temperature using a unique laser probe beam. This has been achieved by the development of a novel probe design associated with a fully automated servo-controlled optical bench, initially developed to stabilize the electric field sensor response. The developed electro-optic probes present a stable response in outdoors conditions over a time duration exceeding 1 h, a frequency bandwidth from kHz to tens of GHz with a sensitivity of 0.7 Vm(-1)Hz(-(1/2)), and a temperature accuracy of 40 mK.

  19. Bubbling effect in the electro-optic delayed feedback oscillator coupled network

    Science.gov (United States)

    Liu, Lingfeng; Lin, Jun; Miao, Suoxia

    2017-03-01

    Synchronization in the optical systems coupled network always suffers from bubbling events. In this paper, we numerically investigate the statistical properties of the synchronization characteristics and bubbling effects in the electro-optic delayed feedback oscillator coupled network with different coupling strength, delay time and gain coefficient. Furthermore, we compare our results with the synchronization properties of semiconductor laser (SL) coupled network, which indicates that the electro-optic delayed feedback oscillator can be better to suppress the bubbling effects in the synchronization of coupled network under the same conditions.

  20. Systems engineering and analysis of electro-optical and infrared systems

    CERN Document Server

    Arrasmith, William Wolfgang

    2015-01-01

    Introduction to Electro-optic and Infrared (EO/IR) Systems Engineering?Radiation in the Visible and Infrared Parts of the Electromagnetic SpectrumRadiation SourcesThe Effect of the Atmosphere on Optical PropagationBasic OpticsOptical ModulationThe Detection of Optical RadiationNoise in the Optical Detection ProcessTechnical Performance Measures and Metrics of Optical DetectorsModern Detectors and their Measures of PerformanceThe Effects of Cooling on Optical Detector NoiseSignal and Image ProcessingElectro-Optic and Infrared Systems AnalysisLaser Imaging Systems?Spectral Imaging?LIDAR and LADA

  1. Coulomb field strength measurement by electro-optic spectral decoding system at the CALIFES beam line

    CERN Document Server

    Pan, R; Lefevre, T; Gillepsie, WA; CERN. Geneva. ATS Department

    2015-01-01

    Electro-optic (EO) techniques are increasingly used for longitudinal bunch profile measurements. A bunch profile monitor, based on electro-optic spectral decoding(EOSD), has been developed and demonstrated on the CALIFES beam line at CERN. The EO response is analysed using a frequency domain description, and two methods for extraction of absolute Coulomb field strengths from the electron bunch are demonstrated. Measurements at field strengths up to 1.3 MV/m agree with the expectation based on independent charge measurements.

  2. Linear electro-optical properties of tetragonal BaTiO3

    Indian Academy of Sciences (India)

    P U Sastry

    2002-09-01

    Linear optical susceptibility and clamped linear electro-optical tensor coefficients of tetragonal BaTiO3 are calculated using a formalism based on bond charge theory. Calculated values are in close agreement with experimental data. The covalent Ti–O bonds constituting distorted TiO6 octahedral groups are found to be major contributors to the electro-optic coefficients making them more sensitive than the BaO12 groups for these properties. Orientations of chemical bonds play an important role in determining these properties.

  3. A new generation of previously unrealizable photonic devices as enabled by a unique electro-optic waveguide architecture

    Science.gov (United States)

    Davis, Scott R.; Rommel, Scott D.; Farca, George; Anderson, Michael H.

    2008-08-01

    A new electro-optic waveguide platform, which provides unprecedented electro-optical phase delays (> 1mm), with very low loss (integrated photonic architecture has applications in a wide array of commercial and defense markets including: remote sensing, micro-LADAR, OCT, laser illumination, phased array radar, optical communications, etc. Performance attributes of several example devices are presented.

  4. Electro-Optics of an Experimental Quantum-Optical Photometer

    Science.gov (United States)

    Solomos, N. H.

    2010-07-01

    The first working version of a new ultrafast three-beam photon counting photometer (QOP) has been materialized and demonstrated by the Applied Physics / Electro-optics Laboratory of the Hellenic Naval Academy in Piraeus. The QOP has been installed on the new 0.51m TVD telescope. The instrument is currently being used for quantum-optical study of atmospheric transmission in green monochromatic light over slant paths, at the RFK/Eudoxos Observatories. Actively quenched Single Photon Avalanche Diode detectors can be interchangeably deployed in addition to PMTs and LLL-CCDs. It is also intended for the testing of various approaches for solving the difficult problem of coupling light efficiently to the very small sensitive areas of SPADS, either using fiber couplers, or novel technologies like dedicated fiber tapers. Some particulars of the instrument design philosophy and its optomechanical construction are very briefly mentioned further below. However, it is appropriate to comment, firstly, on its purpose/rationale: The successful formalism of Glauber that led to the quantum-optical framework pertinent to the study of light in the terrestrial laboratories could, perhaps, be proven equally fruitful if applied to celestial light as well. Adopting the new idea of describing an arbitrary light state in terms of coherence functions, it is easily concluded that conventional astronomical instrumentation measures only spatial (imaging) or temporal (spectroscopy) coherence properties of the incoming photon stream. However, higher order spatiotemporal coherence (manifested as correlations among separated photon detection events) convey blueprints of the emission mechanism itself or even of the photon scattering history written in the course of the long path from the emitter to the telescope. To extract this information, high photon fluxes and unprecedented timing resolutions are needed. Our gradual entrance to the era of Extremely Large Telescopes combined with certain new

  5. Discrete spatial solitons formed in periodically poled lithium niobate by electro-optical effect

    Institute of Scientific and Technical Information of China (English)

    Xi Gu (顾希); Xianfeng Chen (陈险峰); Yuping Chen (陈玉萍); Yuxing Xia (夏宇兴); Yingli Chen (陈英礼)

    2003-01-01

    We report the numerical observation of discrete spatial solitons in a periodically poled lithium niobate waveguide array by applying an electrical field through electro-optical effect. We show that discrete spatial soliton can be controlled by applied voltage in the periodically poled lithium niobate.

  6. Recent Progress in Silicon Electro-optic Modulators for High Speed Applications

    Institute of Scientific and Technical Information of China (English)

    XIAO Xi; YU Jin-zhong

    2008-01-01

    Silicon-based high-speed electro-optical modulator is the key component of silicon photonics for future communiction and interconnection systems. In this paper, introduced are the optical mudulation mechanisms in silicon, reviewed are some recent progresses in high-speed silicon modulators, and analyzed are advantages and shortages of the silicon modulators of different types.

  7. Optimization of electro-optic phase shifters for integrated optical phased arrays

    Science.gov (United States)

    Macik, Dwayne D.; Bravo, Tyler E.; Pentecost, Seeley M.; Espinal, Francisco A.; Madsen, Christi K.

    2017-05-01

    A low-loss, high-speed optical phased array (OPA) has been designed and fabricated. Two different platforms have been utilized in combination to leverage electro-optic (EO) tuning. A lithium niobate (LiNbO3) optical phased array was fabricated and used in conjunction with a silicon nitride (Si3N4) 8x8 waveguide array that condenses the output pitch and utilizes the TriplexTM waveguide technology. This OPA allows for the non-mechanical beam steering (NMBS) of 1550 nm light on an edge coupled optic platform and takes advantage of the high electro-optic coefficient and high speed capability of LiNbO3 for electro-optic phase tuning. This coupled OPA has an overall insertion loss of 3.5 dB which is advantageous to silicon-on-insulator OPAs that have shown overall insertion losses of 14 dB. To characterize and tune this device, a 3 lens imaging system was employed to produce both near- and far- field intensity patterns of the output of the OPA on a static image plane. At the image plane, a high resolution infrared camera was used to observe the resulting intensity pattern. The control software for tuning the OPA reads the intensity incident at a specified position on the detector array, and has a PWM interface to drive the electro-optic phase controls. Beam steering was accomplished using an iterative tuning algorithm.

  8. Quantum nondemolition measurement with a nonclassical meter input and an electro-optic enhancement

    DEFF Research Database (Denmark)

    Andersen, Ulrik Lund; Buchler, B.C.; Bachor, H.A.

    2002-01-01

    Optical quantum nondemolition measurements are performed using a beamsplitter with a nonclassical meter input and a electro-optic feedforward loop. The nonclassical meter input is provided by a stable 4.5 dB amplitude squeezed source generated by an optical parametric amplifier. We show...

  9. Electro-Optical Interference Laser Radiation Modulator (Elektroopticheskii Interfentsionnyi Modulyator Lazernogo Izlucheniya),

    Science.gov (United States)

    A modulator constructed on the basis of the Rozhdestvenskiy interferometer has been described. Characteristic static curves have been obtained in a... modulator working with one or two electro-optical crystals. A comparison of the interference and ordinary amplitude modulators has been given. (Author)

  10. Large-area Fabry-Perot modulator based on electro-optic polymers

    DEFF Research Database (Denmark)

    Benter, Nils; Bertram, Ralph Peter; Soergel, Elisabeth

    2006-01-01

    We present a large-area electro-optic Fabry-Perot modulator utilizing a photoaddressable bis-azo polymer placed between two dielectric mirrors with an open aperture of 2 cm. A modulation efficientcy of 1% at an effective modulation voltage of 20 V for a wavelength of 1.55 mymeter is demonstrated...

  11. Extreme nonlinear terahertz electro-optics in diamond for ultrafast pulse switching

    Science.gov (United States)

    Shalaby, Mostafa; Vicario, Carlo; Hauri, Christoph P.

    2017-03-01

    Polarization switching of picosecond laser pulses is a fundamental concept in signal processing [C. Chen and G. Liu, Annu. Rev. Mater. Sci. 16, 203 (1986); V. R. Almeida et al., Nature 431, 1081 (2004); and A. A. P. Pohl et al., Photonics Sens. 3, 1 (2013)]. Conventional switching devices rely on the electro-optical Pockels effect and work at radio frequencies. The ensuing gating time of several nanoseconds is a bottleneck for faster switches which is set by the performance of state-of-the-art high-voltage electronics. Here we show that by substituting the electric field of several kV/cm provided by modern electronics by the MV/cm field of a single-cycle THz laser pulse, the electro-optical gating process can be driven orders of magnitude faster, at THz frequencies. In this context, we introduce diamond as an exceptional electro-optical material and demonstrate a pulse gating time as fast as 100 fs using sub-cycle THz-induced Kerr nonlinearity. We show that THz-induced switching in the insulator diamond is fully governed by the THz pulse shape. The presented THz-based electro-optical approach overcomes the bandwidth and switching speed limits of conventional MHz/GHz electronics and establishes the ultrafast electro-optical gating technology for the first time in the THz frequency range. We finally show that the presented THz polarization gating technique is applicable for advanced beam diagnostics. As a first example, we demonstrate tomographic reconstruction of a THz pulse in three dimensions.

  12. Polymer stabilized liquid crystals: Topology-mediated electro-optical behavior and applications

    Science.gov (United States)

    Weng, Libo

    There has been a wide range of liquid crystal polymer composites that vary in polymer concentration from as little as 3 wt.% (polymer stabilized liquid crystal) to as high as 60 wt.% (polymer dispersed liquid crystals). In this dissertation, an approach of surface polymerization based on a low reactive monomer concentration about 1 wt.% is studied in various liquid crystal operation modes. The first part of dissertation describes the development of a vertical alignment (VA) mode with surface polymer stabilization, and the effects of structure-performance relationship of reactive monomers (RMs) and polymerization conditions on the electro-optical behaviors of the liquid crystal device has been explored. The polymer topography plays an important role in modifying and enhancing the electro-optical performance of stabilized liquid crystal alignment. The enabling surface-pinned polymer stabilized vertical alignment (PSVA) approach has led to the development of high-performance and fast-switching displays with controllable pretilt angle, increase in surface anchoring energy, high optical contrast and fast response time. The second part of the dissertation explores a PSVA mode with in-plane switching (IPS) and its application for high-efficiency and fast-switching phase gratings. The diffraction patterns and the electro-optical behaviors including diffraction efficiency and response time are characterized. The diffraction grating mechanism and performance have been validated by computer simulation. Finally, the advantages of surface polymerization approach such as good optical contrast and fast response time have been applied to the fringe-field switching (FFS) system. The concentration of reactive monomer on the electro-optical behavior of the FFS cells is optimized. The outstanding electro-optical results and mechanism of increase in surface anchoring strength are corroborated by the director field simulation. The density and topology of nanoscale polymer protrusions

  13. Extreme nonlinear terahertz electro-optics in diamond for ultrafast pulse switching

    Directory of Open Access Journals (Sweden)

    Mostafa Shalaby

    2017-03-01

    Full Text Available Polarization switching of picosecond laser pulses is a fundamental concept in signal processing [C. Chen and G. Liu, Annu. Rev. Mater. Sci. 16, 203 (1986; V. R. Almeida et al., Nature 431, 1081 (2004; and A. A. P. Pohl et al., Photonics Sens. 3, 1 (2013]. Conventional switching devices rely on the electro-optical Pockels effect and work at radio frequencies. The ensuing gating time of several nanoseconds is a bottleneck for faster switches which is set by the performance of state-of-the-art high-voltage electronics. Here we show that by substituting the electric field of several kV/cm provided by modern electronics by the MV/cm field of a single-cycle THz laser pulse, the electro-optical gating process can be driven orders of magnitude faster, at THz frequencies. In this context, we introduce diamond as an exceptional electro-optical material and demonstrate a pulse gating time as fast as 100 fs using sub-cycle THz-induced Kerr nonlinearity. We show that THz-induced switching in the insulator diamond is fully governed by the THz pulse shape. The presented THz-based electro-optical approach overcomes the bandwidth and switching speed limits of conventional MHz/GHz electronics and establishes the ultrafast electro-optical gating technology for the first time in the THz frequency range. We finally show that the presented THz polarization gating technique is applicable for advanced beam diagnostics. As a first example, we demonstrate tomographic reconstruction of a THz pulse in three dimensions.

  14. An approach for a comprehensive automation of electro-optical (EO) sensor characterization setups

    Science.gov (United States)

    Dave, Amit; Sharma, Jitendra; Sukheja, Anil; Kumar, Sumit; Mishra, Ashish; Goswami, D. R.

    2016-05-01

    Space Applications Centre develops various electro-optical (EO) sensors for space borne platforms and inter-planetary missions. Sensor complexities vary for different applications and therefore performance evaluation and characterization pose different challenges. Performance optimization tasks demand repeated measurements and characterization needs to be done under different phases of testing. It is difficult to meet such requirements in case of short sensor development lifecycles or tight schedules. Activities which are amenable to automation are identified and targeted to reduce the manual intervention and to avoid delays due to errors and to speed up the overall activity. Laboratory instruments, either in-house developed or COTS, play an important role in automating the test setup as they have different types of interfaces and have their own complications. In order to make an automated test setup, software intelligence need to be built based on the instrument feedback and the other check points based on the test sequence. A complete automation needs machine intelligence and sufficient amount of traceability, so that the process can be easily verified for confidence. Overall software architecture should be such that it allows connecting various types of instruments, decision making based on output of the device under test, complete traceability and fault tolerance. In this paper authors have identified the activities that can be automated for various EO sensor categories and approaches are discussed for automation with radiometric calibration, spectral response measurement and focusing as test cases. Also, software architecture is presented which allows uniform access to instruments, back-end database and macro level automation process.

  15. Electro-optic testbed utilizing a dynamic range gated Rayleigh beacon for atmospheric turbulence profiling

    Science.gov (United States)

    Zuraski, Steven M.; Fiorino, Steven T.; Beecher, Elizabeth A.; Figlewski, Nathan M.; Schmidt, Jason D.; McCrae, Jack E.

    2016-10-01

    The Photometry Analysis and Optical Tracking and Evaluation System (PANOPTES) Quad Axis Telescope is a unique four axis mount Ritchey-Chretien 24 inch telescope capable of tracking objects through the zenith without axes rotation delay (no Dead Zone). This paper describes enhancement components added to the quad axis mount telescope that will enable measurements supporting novel research and field testing focused on `three-dimensional' characterization of turbulent atmospheres, mitigation techniques, and new sensing modalities. These all support research and operational techniques relating to astronomical imaging and electro-optical propagation though the atmosphere, relative to sub-meter class telescopes in humid, continental environments. This effort will use custom designed and commercial off the shelf hardware; sub-system components discussed will include a wavefront sensor system, a co-aligned beam launch system, and a fiber coupled research laser. The wavefront sensing system has the ability to take measurements from a dynamic altitude adjustable laser beacon scattering spot, a key concept that enables rapid turbulence structure parameter measurements over an altitude varied integrated atmospheric volume. The sub-components are integrated with the overall goal of measuring a height-resolved volumetric profile for the atmospheric turbulence structure parameter at the site, and developing mobile techniques for such measurements. The design concept, part selection optimization, baseline component lab testing, and initial field measurements, will be discussed in the main sections of this paper. This project is a collaborative effort between the Air Force Research Labs Sensors Directorate and the Air Force Institute of Technology Center for Directed Energy.

  16. Hybrid electro-optical stimulation of the rat sciatic nerve induces force generation in the plantarflexor muscles

    Science.gov (United States)

    Duke, Austin R.; Peterson, Erik; Mackanos, Mark A.; Atkinson, James; Tyler, Dustin; Jansen, E. Duco

    2012-12-01

    Objective. Optical methods of neural activation are becoming important tools for the study and treatment of neurological disorders. Infrared nerve stimulation (INS) is an optical technique exhibiting spatially precise activation in the native neural system. While this technique shows great promise, the risk of thermal damage may limit some applications. Combining INS with traditional electrical stimulation, a method known as hybrid electro-optical stimulation, reduces the laser power requirements and mitigates the risk of thermal damage while maintaining spatial selectivity. Here we investigate the capability of inducing force generation in the rat hind limb through hybrid stimulation of the sciatic nerve. Approach. Hybrid stimulation was achieved by combining an optically transparent nerve cuff for electrical stimulation and a diode laser coupled to an optical fiber for infrared stimulation. Force generation in the rat plantarflexor muscles was measured in response to hybrid stimulation with 1 s bursts of pulses at 15 and 20 Hz and with a burst frequency of 0.5 Hz. Main results. Forces were found to increase with successive stimulus trains, ultimately reaching a plateau by the 20th train. Hybrid evoked forces decayed at a rate similar to the rate of thermal diffusion in tissue. Preconditioning the nerve with an optical stimulus resulted in an increase in the force response to both electrical and hybrid stimulation. Histological evaluation showed no signs of thermally induced morphological changes following hybrid stimulation. Our results indicate that an increase in baseline temperature is a likely contributor to hybrid force generation. Significance. Extraneural INS of peripheral nerves at physiologically relevant repetition rates is possible using hybrid electro-optical stimulation.

  17. Computational Study of Linear and Nonlinear Optical Properties of Single Molecules and Clusters of Organic Electro-Optic Chromophores

    Science.gov (United States)

    Garrett, Kerry

    Organic electro-optic (OEO) materials integrated into silicon-organic hybrid (SOH) devices afford significant improvements in size, weight, power, and bandwidth (SWAP) performance of integrated electronic/photonic systems critical for current and next generation telecommunication, computer, sensor, transportation, and defense technologies. Improvement in molecular first hyperpolarizability, and in turn electro-optic activity, is crucial to further improvement in the performance of SOH devices. The timely preparation of new chromophores with improved molecular first hyperpolarizability requires theoretical guidance; however, common density functional theory (DFT) methods often perform poorly for optical properties in systems with substantial intramolecular charge transfer character. The first part of this dissertation describes the careful evaluation of popular long-range correction (LC) and range-separated hybrid (RSH) density functional theory (DFT) for definition of structure/function relationships crucial for the optimization of molecular first hyperpolarizability, beta. In particular, a benchmark set of well-characterized OEO chromophores is used to compare calculated results with the corresponding experimentally measured linear and nonlinear optical properties; respectively, the wavelength of the peak one-photon absorption energy, lambdamax, and beta. A goal of this work is to systematically determine the amount of exact exchange in LC/RSH-DFT methods required for accurately computing these properties for a variety OEO chromophores. High-level electron correlation (post-Hartree-Fock) methods are also investigated and compared with DFT. Included are results for the computation of beta using second-order Moller-Plesset perturbation theory (MP2) and the double-hybrid method, B2PLYP. The second part of this work transitions from single-molecule studies to computing bulk electronic and nonlinear optical properties of molecular crystals and isotropic ensembles of a

  18. Real-time digital signal processing for live electro-optic imaging.

    Science.gov (United States)

    Sasagawa, Kiyotaka; Kanno, Atsushi; Tsuchiya, Masahiro

    2009-08-31

    We present an imaging system that enables real-time magnitude and phase detection of modulated signals and its application to a Live Electro-optic Imaging (LEI) system, which realizes instantaneous visualization of RF electric fields. The real-time acquisition of magnitude and phase images of a modulated optical signal at 5 kHz is demonstrated by imaging with a Si-based high-speed CMOS image sensor and real-time signal processing with a digital signal processor. In the LEI system, RF electric fields are probed with light via an electro-optic crystal plate and downconverted to an intermediate frequency by parallel optical heterodyning, which can be detected with the image sensor. The artifacts caused by the optics and the image sensor characteristics are corrected by image processing. As examples, we demonstrate real-time visualization of electric fields from RF circuits.

  19. Ultrabroadband Electro-Optic Modulator Based on Hybrid Silicon-Polymer Dual Vertical Slot Waveguide

    Directory of Open Access Journals (Sweden)

    Shouyuan Shi

    2011-01-01

    Full Text Available We present a novel hybrid silicon-polymer dual slot waveguide for high speed and ultra-low driving voltage electro-optic (EO modulation. The proposed design utilizes the unique properties of ferroelectric materials such as LiNbO3 to achieve dual RF and optical modes within a low index nanoslot. The tight mode concentration and overlap in the slot allow the infiltrated organic EO polymers to experience enhanced nonlinear interaction with the applied electric field. Half-wavelength voltage-length product and electro-optic response are rigorously simulated to characterize the proposed design, which reveals ultrabroadband operation, up to 250 GHz, and subvolt driving voltage for a 1 cm long modulator.

  20. Novel Electro-Optical Modulator Utilizing GeO2-Doped Silica Waveguide

    Institute of Scientific and Technical Information of China (English)

    LI Jiusheng; JIA Dagong

    2009-01-01

    In order to achieve a modulator with broad bandwidth and perfect impedance match,a novel electro-optical modulator based on GeO2-doped silica waveguides on silicon substrate is designed.The finite element model of the whole electro-optical modulator is established by means of ANSYS.With the finite element method analysis,the performance of the novel modulator is predicted.The simulation reveals that the designed modulator operates with a product of 3 dB optical bandwidth and modulating length of 226.59 GHz-cm,and a characteristic impedance of 51.6 Ω at 1 550 nm wavelength.Moreover,the calculated electrical reflected power of coplanar waveguide electrode is below -20 dB in the frequency ranging from 45 MHz to 65 GHz.Therefore,the designed modulator has wide modulation bandwidth and perfect impedance match.

  1. Effective electro-optical modulation with high extinction ratio by a graphene-silicon microring resonator

    DEFF Research Database (Denmark)

    Ding, Yunhong; Zhu, Xiaolong; Xiao, Sanshui

    2015-01-01

    comprehensively study the interaction between graphene and a microring resonator, and its influence on the optical modulation depth. We demonstrate graphene-silicon microring devices showing a high modulation depth of 12.5 dB with a relatively low bias voltage of 8.8 V. On-off electro-optical switching......Graphene opens up for novel optoelectronic applications thanks to its high carrier mobility, ultra-large absorption bandwidth, and extremely fast material response. In particular, the opportunity to control optoelectronic properties through tuning of the Fermi level enables electro-optical...... modulation, optical-optical switching, and other optoelectronics applications. However, achieving a high modulation depth remains a challenge because of the modest graphene-light interaction in the graphene-silicon devices, typically, utilizing only a monolayer or few layers of graphene. Here, we...

  2. High-speed and low-power electro-optical DSP coprocessor.

    Science.gov (United States)

    Tamir, Dan E; Shaked, Natan T; Wilson, Peter J; Dolev, Shlomi

    2009-08-01

    A fast, power-efficient electro-optical vector-by-matrix multiplier (VMM) architecture is presented. Careful design of an electrical unit supporting high-speed data transfer enables this architecture to overcome bottlenecks encountered by previous VMM architectures. Based on the proposed architecture, we present an electro-optical digital signal processing (DSP) coprocessor that can achieve a significant speedup of 2-3 orders of magnitude over existing DSP technologies and execute more than 16 teraflops. We show that it is feasible to implement the system using off-the-shelf components, analyze the performance of the architecture with respect to primitive DSP operations, and detail the use of the new architecture for several DSP applications.

  3. Paraxial Theory of Direct Electro-optic Sampling of the Quantum Vacuum

    Science.gov (United States)

    Moskalenko, A. S.; Riek, C.; Seletskiy, D. V.; Burkard, G.; Leitenstorfer, A.

    2015-12-01

    Direct detection of vacuum fluctuations and analysis of subcycle quantum properties of the electric field are explored by a paraxial quantum theory of ultrafast electro-optic sampling. The feasibility of such experiments is demonstrated by realistic calculations adopting a thin ZnTe electro-optic crystal and stable few-femtosecond laser pulses. We show that nonlinear mixing of a short near-infrared probe pulse with the multiterahertz vacuum field leads to an increase of the signal variance with respect to the shot noise level. The vacuum contribution increases significantly for appropriate length of the nonlinear crystal, short pulse duration, tight focusing, and a sufficiently large number of photons per probe pulse. If the vacuum input is squeezed, the signal variance depends on the probe delay. Temporal positions with a noise level below the pure vacuum may be traced with subcycle resolution.

  4. Femtosecond fibre laser stabilisation to an optical frequency standard using a KTP electro-optic crystal

    Energy Technology Data Exchange (ETDEWEB)

    Nyushkov, B N [Novosibirsk State University, Novosibirsk (Russian Federation); Pivtsov, V S; Koliada, N A [Institute of Laser Physics, Siberian Branch, Russian Academy of Sciences, Novosibirsk (Russian Federation); Kaplun, A B; Meshalkin, A B [S.S. Kutateladze Institute of Heat Physics, Siberian Division of the Russian Academy of Sciences, Novosibirsk (Russian Federation)

    2015-05-31

    A miniature intracavity KTP-based electro-optic phase modulator has been developed which can be used for effective stabilisation of an optical frequency comb of a femtosecond erbiumdoped fibre laser to an optical frequency standard. The use of such an electro-optic modulator (EOM) has made it possible to extend the working frequency band of a phase-locked loop system for laser stabilisation to several hundred kilohertz. We demonstrate that the KTP-based EOM is sufficiently sensitive even at a small optical length, which allows it to be readily integrated into cavities of femtosecond fibre lasers with high mode frequency spacings (over 100 MHz). (extreme light fields and their applications)

  5. Nuclear reactor pulse calibration using a CdZnTe electro-optic radiation detector

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Kyle A., E-mail: knelson1@ksu.edu [S.M.A.R.T. Laboratory, Mechanical and Nuclear Engineering, Kansas State University, Manhattan, KS 66506 (United States); Geuther, Jeffrey A. [TRIGA Mark II Nuclear Reactor, Mechanical and Nuclear Engineering, Kansas State University, Manhattan, KS 66506 (United States); Neihart, James L.; Riedel, Todd A. [S.M.A.R.T. Laboratory, Mechanical and Nuclear Engineering, Kansas State University, Manhattan, KS 66506 (United States); Rojeski, Ronald A. [Nanometrics, Inc., 1550 Buckeye Drive, Milpitas, CA 95035 (United States); Saddler, Jeffrey L. [TRIGA Mark II Nuclear Reactor, Mechanical and Nuclear Engineering, Kansas State University, Manhattan, KS 66506 (United States); Schmidt, Aaron J.; McGregor, Douglas S. [S.M.A.R.T. Laboratory, Mechanical and Nuclear Engineering, Kansas State University, Manhattan, KS 66506 (United States)

    2012-07-15

    A CdZnTe electro-optic radiation detector was used to calibrate nuclear reactor pulses. The standard configuration of the Pockels cell has collimated light passing through an optically transparent CdZnTe crystal located between crossed polarizers. The transmitted light was focused onto an IR sensitive photodiode. Calibrations of reactor pulses were performed using the CdZnTe Pockels cell by measuring the change in the photodiode current, repeated 10 times for each set of reactor pulses, set between 1.00 and 2.50 dollars in 0.50 increments of reactivity. - Highlights: Black-Right-Pointing-Pointer We demonstrated the first use of an electro-optic device to trace reactor pulses in real-time. Black-Right-Pointing-Pointer We examined the changes in photodiode current for different reactivity insertions. Black-Right-Pointing-Pointer Created a linear best fit line from the data set to predict peak pulse powers.

  6. Algebraic approach to electro-optic modulation of light: Exactly solvable multimode quantum model

    CERN Document Server

    Miroshnichenko, George P; Trifanov, Alexander I; Gleim, Artur V

    2016-01-01

    We theoretically study electro-optic light modulation based on the quantum model where the linear electro-optic effect and the externally applied microwave field result in the interaction between optical cavity modes. The model assumes that the number of interacting modes is finite and effects of the mode overlapping coefficient on the strength of the intermode interaction can be taken into account through dependence of the coupling coefficient on the mode characteristics. We show that, under certain conditions, the model is exactly solvable and, in the semiclassical approximation where the microwave field is treated as a classical mode, can be analyzed using the technique of the Jordan mappings for the su(2) Lie algebra. Analytical results are applied to study effects of light modulation on the frequency dependence of the photon counting rate. We also establish the conditions of validity of the semiclassical approximation by applying the methods of polynomially deformed Lie algebras for analysis of the model...

  7. INCREASING MEASUREMENT ACCURACY IN ELECTRO-OPTICAL METHOD FOR MEASURING VELOCITY OF DETONATION

    Directory of Open Access Journals (Sweden)

    Mario Dobrilović

    2014-12-01

    Full Text Available In addition to other detonation parameters detonation velocity is a value that provides indirect information on the strength i.e. brisance of an explosive and explosive performance. In addition to that, detonation velocity is a value which can be measured in a relatively simpler and more precise manner, by developed and accessible methods when compared to other detonation parameters Due to its simple use, compact instruments and satisfactory accuracy, electro-optical method of detonation velocity measurement is widely used. The paper describes the electro-optical measurement method and points out the factors that affect its accuracy. The accuracy of measurement is increased and measurement uncertainty is reduced by the measurement result analysis with the application of different measurement setups.

  8. Latest electro-optic and photonic devices for security and military applications

    Science.gov (United States)

    Jha, A. R.

    2006-09-01

    This paper reveals performance capabilities of state-of-the-art electro-optic and photonic devices, which are best suited for security and defense system applications. These devices can be used in battlefield, space surveillance, medical diagnosis, and detection of terrorist activities. Performance capabilities of fiber optic components for possible applications in WDM and DWDM systems are summarized. Photonic devices for covert military and security communication applications are identified with particular emphasis on performance and reliability. Performance parameters of Erbium-doped fiber amplifiers (EDFAs), Erbium-doped waveguide amplifiers (EDWAs), and optical hybrid amplifiers (OHAs) comprising of EDFAs and Raman amplifiers are discussed with emphasis on bandwidth, gain-flatness, data handling capability, channel capacity and cost-effectiveness. Performance parameters of very long wavelength infrared (VLWIR) detectors are summarized, which have potential applications in remote sensing and ballistic missile defense applications. Electro-optic and photonic devices best suited for security and defense applications are identified.

  9. Electro-optical Measurements of Ultrashort 45 MeV Electron Beam Bunches

    CERN Document Server

    Tsang, Thomas; Kowalski, L A; Larsen, R; Lazarus, D M; Nikas, D; Ozben, C; Semertzidis, Y K; Srinivasan-Rao, T

    2000-01-01

    We have measured the temporal duration of 45 MeV picosecond electron beam bunches using a noninvasive electro-optical (EO) technique. The amplitude of the EO modulation was found to increase linearly with electron beam charge and decrease inversely with distance from the electron beam. The risetime of the temporal signal was limited by our detection system to ~70ps. The EO signal due to ionization caused by the electrons traversing the EO crystal was also observed. It has a distinctively long decay time constant and signal polarity opposite to that due to the field induced by the electron beam. The electro-optical technique may be ideal for the measurement of bunch length of femtosecond, relativistic, high energy, charged, particle beams.

  10. Low-power Terahertz Time-Domain Spectroscopy with optimized electro-optical detection

    DEFF Research Database (Denmark)

    Gorenflo, Stefan; Hinkov, Iliyana; Lambrecht, Armin

    2005-01-01

    A Terahertz Time-Domain Spectroscopy (THz-TDS) system with electro-optical detector based on a ZnTe crystal is presented. The pump laser is a Ti:Sa laser with pulse duration of approx. 10 fs at a central wavelength of 800 nm. Using an optimized detection configuration, a signal-to-noise ratio bet...... better than 103 is achieved, applying an optical laser power of only 25mW. Several substances can be clearly distinguished on the basis of their specific THz absorption spectra.......A Terahertz Time-Domain Spectroscopy (THz-TDS) system with electro-optical detector based on a ZnTe crystal is presented. The pump laser is a Ti:Sa laser with pulse duration of approx. 10 fs at a central wavelength of 800 nm. Using an optimized detection configuration, a signal-to-noise ratio...

  11. Silicon electro-optic modulator with high-permittivity gate dielectric layer

    Institute of Scientific and Technical Information of China (English)

    Mengxia Zhu; Zhiping Zhou; Dingshan Gao

    2009-01-01

    A high-permittivity (high-k) material is applied as the gate dielectric layer in a silicon metal-oxidesemiconductor (MOS) capacitor to form a special electro-optic (EO) modulator.Both induced charge density and modulation efficiency in the proposed modulator are improved due to the special structure design and the application of the high-k material.The device has an ultra-compact dimension of 691 μm in length.

  12. Wideband Analog Transmission System Based on the External Intensity Electro-Optic Modulator

    Directory of Open Access Journals (Sweden)

    Jiri Svarny

    2016-01-01

    Full Text Available The work deals with design and integration of an analog electro-optic transmission system suitable for some specialized tasks of diagnostics and measurements. The system is based on principle of external intensity modulation of fiber guided laser radiation. Besides wideband and almost lossless transmission the system tolerates extreme length of the transmitting medium and ensures ultimate galvanic barrier between the input and output.

  13. Electro-optical measurements of 3D-stc detectors fabricated at ITC-irst

    Energy Technology Data Exchange (ETDEWEB)

    Zoboli, Andrea [INFN and Department of ICT, University of Trento, via Sommarive, 14 - 38050 Povo di Trento (Italy)], E-mail: zoboli@dit.unitn.it; Boscardin, Maurizio [ITC-irst, Microsystems Division, via Sommarive, 18 - 38050 Povo di Trento (Italy); Bosisio, Luciano [INFN and Department of Physics, University of Trieste, via A. Valerio, 2 - 34127 Trieste (Italy); Dalla Betta, Gian-Franco [INFN and Department of ICT, University of Trento, via Sommarive, 14 - 38050 Povo di Trento (Italy); Piemonte, Claudio; Pozza, Alberto; Ronchin, Sabina; Zorzi, Nicola [ITC-irst, Microsystems Division, via Sommarive, 18 - 38050 Povo di Trento (Italy)

    2007-12-11

    In the past two years 3D silicon radiation detectors have been developed at ITC-irst (Trento, Italy). As a first step toward full 3D devices, simplified structures featuring columnar electrodes of one doping type only were fabricated. This paper reports the electro-optical characterization of 3D test diodes made with this approach. Experimental results and TCAD simulations provide good insight into the charge collection mechanism and response speed limitation of these structures.

  14. Electro-optical cavity-dumped Ce:Nd:YAG laser for aesthetic medicine

    Science.gov (United States)

    Lv, Yuandong; Liu, Jiaqi; Hao, Lijun

    2012-11-01

    An electro-optical cavity-dumped 20 Hz Ce:Nd:YAG laser with an optimized thermal-insensitive concavo-convex cavity for aesthetic medicine was demonstrated. The pulse width remained constant at 6.0 ns. The maximum output energy and peak power were 120 mJ and 20 MW, respectively. The average output energy was very stable. The fluctuations of average output energy within 6 cycles and 10 min were 0.89% and 7.9%, respectively.

  15. Photoluminescence and electro-optic properties of small (25-35 nm diameter) quantum boxes

    Science.gov (United States)

    Davis, L.; Ko, K. K.; Li, W.-Q.; Sun, H. C.; Lam, Y.; Brock, T.; Pang, S. W.; Bhattacharya, P. K.; Rooks, M. J.

    1993-05-01

    The luminescence and electro-optic properties of buried 25-35 nm quantum boxes have been measured. The quantum boxes were defined by a combination of molecular beam epitaxial growth and regrowth, electron beam lithography, and dry etching. The photoluminescence from 35 nm boxes shows a blue shift of about 15 meV compared to the bulk luminescence and an enhancement, taking into account the fill factor. An enhanced effective linear electrooptic coefficient is observed for the quantum boxes.

  16. A Community Format for Electro-Optic Space Situational Awareness (EOSSA) Data Products

    Science.gov (United States)

    2014-09-01

    Awareness (SSA) community. With the increase in the number of Electro-Optical (EO) sensors collecting photometric, radiometric , and spectroscopic data...Optical (EO) sensors collecting photometric, radiometric , and spectroscopic data on man-made Resident Space Objects (RSOs) for Space Situational...comply with a collection of information if it does not display a currently valid OMB control number. 1. REPORT DATE SEP 2014 2. REPORT TYPE 3. DATES

  17. Optimum design of a polymer electro-optic microring resonator switch

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Novel transfer functions are presented for a polymer electro-optic microring resonator switches. The resonating process of the light in the microring is simulated using the formulas. Then the optimization of the structural parameters is performed,and the characteristics are analyzed, such as the resonance time, output spectrum, operation voltage, insertion loss and crosstalk were analyzed. The simulation results show that the designed device exhibits favorable switching functions.

  18. An Electro-Optic Modulator Based on GeO2-Doped Silica Ridge Waveguides with Thermal Poling

    Institute of Scientific and Technical Information of China (English)

    曹霞; 何赛灵

    2003-01-01

    A Mach-Zehnder electro-optic modulator is designed and fabricated based on upper-clad GeO2-doped silica ridge waveguides with thermal poling. The electro-optic coefficient obtained is about 0.05 pm/V and is polarizationinsensitive. An extinction ratio of over 17dB is achieved. The transmission loss of the modulator for the TE mode is 2-3 dB higher than that for the TM mode after the poling.

  19. On-chip electro-optic tuning of a lithium niobate microresonator with integrated in-plane microelectrodes

    CERN Document Server

    Wang, Min; Fang, Zhiwei; Liao, Yang; Wang, Peng; CHu, Wei; Qiao, Lingling; Lin, Jintian; Fang, Wei; Cheng, Ya

    2016-01-01

    We demonstrate electro-optic tuning of an on-chip lithium niobate microresonator with integrated in-plane microelectrodes. First two metallic microelectrodes on the substrate were formed via femtosecond laser process. Then a high-Q lithium niobate microresonator located between the microelectrodes was fabricated by femtosecond laser direct writing accompanied by focused ion beam milling. Due to the efficient structure designing, high electro-optical tuning coefficient of 3.41 pm/V was observed.

  20. High frequency electro-optic measurement of strained silicon racetrack resonators

    CERN Document Server

    Borghi, M; Merget, F; Witzens, J; Bernard, M; Ghulinyan, M; Pucker, G; Pavesi, L

    2015-01-01

    The observation of the electro-optic effect in strained silicon waveguides has been considered as a direct manifestation of an induced $\\chi^{(2)}$ non-linearity in the material. In this work, we perform high frequency measurements on strained silicon racetrack resonators. Strain is controlled by a mechanical deformation of the waveguide. It is shown that any optical modulation vanishes independently of the applied strain when the applied voltage varies much faster than the carrier effective lifetime, and that the DC modulation is also largely independent of the applied strain. This demonstrates that plasma carrier dispersion is responsible for the observed electro-optic effect. After normalizing out free carrier effects, our results set an upper limit of $8\\,pm/V$ to the induced high-speed $\\chi^{(2)}_{eff,zzz}$ tensor element at an applied stress of $-0.5\\,GPa$. This upper limit is about one order of magnitude lower than the previously reported values for static electro-optic measurements.

  1. Novel electro-optical coupling technique for magnetic resonance-compatible positron emission tomography detectors.

    Science.gov (United States)

    Olcott, Peter D; Peng, Hao; Levin, Craig S

    2009-01-01

    A new magnetic resonance imaging (MRI)-compatible positron emission tomography (PET) detector design is being developed that uses electro-optical coupling to bring the amplitude and arrival time information of high-speed PET detector scintillation pulses out of an MRI system. The electro-optical coupling technology consists of a magnetically insensitive photodetector output signal connected to a nonmagnetic vertical cavity surface emitting laser (VCSEL) diode that is coupled to a multimode optical fiber. This scheme essentially acts as an optical wire with no influence on the MRI system. To test the feasibility of this approach, a lutetium-yttrium oxyorthosilicate crystal coupled to a single pixel of a solid-state photomultiplier array was placed in coincidence with a lutetium oxyorthosilicate crystal coupled to a fast photomultiplier tube with both the new nonmagnetic VCSEL coupling and the standard coaxial cable signal transmission scheme. No significant change was observed in 511 keV photopeak energy resolution and coincidence time resolution. This electro-optical coupling technology enables an MRI-compatible PET block detector to have a reduced electromagnetic footprint compared with the signal transmission schemes deployed in the current MRI/PET designs.

  2. Novel Electro-Optical Coupling Technique for Magnetic Resonance-Compatible Positron Emission Tomography Detectors

    Directory of Open Access Journals (Sweden)

    Peter D. Olcott

    2009-03-01

    Full Text Available A new magnetic resonance imaging (MRI-compatible positron emission tomography (PET detector design is being developed that uses electro-optical coupling to bring the amplitude and arrival time information of high-speed PET detector scintillation pulses out of an MRI system. The electro-optical coupling technology consists of a magnetically insensitive photodetector output signal connected to a nonmagnetic vertical cavity surface emitting laser (VCSEL diode that is coupled to a multimode optical fiber. This scheme essentially acts as an optical wire with no influence on the MRI system. To test the feasibility of this approach, a lutetium-yttrium oxyorthosilicate crystal coupled to a single pixel of a solid-state photomultiplier array was placed in coincidence with a lutetium oxyorthosilicate crystal coupled to a fast photomultiplier tube with both the new nonmagnetic VCSEL coupling and the standard coaxial cable signal transmission scheme. No significant change was observed in 511 keV photopeak energy resolution and coincidence time resolution. This electro-optical coupling technology enables an MRI-compatible PET block detector to have a reduced electromagnetic footprint compared with the signal transmission schemes deployed in the current MRI/PET designs.

  3. Optical modulation techniques for analog signal processing and CMOS compatible electro-optic modulation

    Science.gov (United States)

    Gill, Douglas M.; Rasras, Mahmoud; Tu, Kun-Yii; Chen, Young-Kai; White, Alice E.; Patel, Sanjay S.; Carothers, Daniel; Pomerene, Andrew; Kamocsai, Robert; Beattie, James; Kopa, Anthony; Apsel, Alyssa; Beals, Mark; Mitchel, Jurgen; Liu, Jifeng; Kimerling, Lionel C.

    2008-02-01

    Integrating electronic and photonic functions onto a single silicon-based chip using techniques compatible with mass-production CMOS electronics will enable new design paradigms for existing system architectures and open new opportunities for electro-optic applications with the potential to dramatically change the management, cost, footprint, weight, and power consumption of today's communication systems. While broadband analog system applications represent a smaller volume market than that for digital data transmission, there are significant deployments of analog electro-optic systems for commercial and military applications. Broadband linear modulation is a critical building block in optical analog signal processing and also could have significant applications in digital communication systems. Recently, broadband electro-optic modulators on a silicon platform have been demonstrated based on the plasma dispersion effect. The use of the plasma dispersion effect within a CMOS compatible waveguide creates new challenges and opportunities for analog signal processing since the index and propagation loss change within the waveguide during modulation. We will review the current status of silicon-based electrooptic modulators and also linearization techniques for optical modulation.

  4. High-frequency electro-optic measurement of strained silicon racetrack resonators.

    Science.gov (United States)

    Borghi, M; Mancinelli, M; Merget, F; Witzens, J; Bernard, M; Ghulinyan, M; Pucker, G; Pavesi, L

    2015-11-15

    The observation of the electro-optic effect in strained silicon waveguides has been considered a direct manifestation of an induced χ(2) nonlinearity in the material. In this work, we perform high-frequency measurements on strained silicon racetrack resonators. Strain is controlled by a mechanical deformation of the waveguide. It is shown that any optical modulation vanishes, independent of the applied strain, when the applied voltage varies much faster than the carrier effective lifetime and that the DC modulation is also largely independent of the applied strain. This demonstrates that plasma carrier dispersion is responsible for the observed electro-optic effect. After normalizing out free-carrier effects, our results set an upper limit of (8±3) pm/V to the induced high-speed effective χeff,zzz(2) tensor element at an applied stress of -0.5 GPa. This upper limit is about 1 order of magnitude lower than previously reported values for static electro-optic measurements.

  5. Ultrahigh Q whispering gallery mode electro-optic resonators on a silicon photonic chip.

    Science.gov (United States)

    Soltani, Mohammad; Ilchenko, Vladimir; Matsko, Andrey; Savchenkov, Anatoliy; Schlafer, John; Ryan, Colm; Maleki, Lute

    2016-09-15

    Crystalline whispering gallery mode (WGM) electro-optic resonators made of LiNbO3 and LiTaO3 are critical for a wide range of applications in nonlinear and quantum optics, as well as RF photonics, due to their remarkably ultrahigh Q(>108) and large electro-optic coefficient. Achieving efficient coupling of these resonators to planar on-chip optical waveguides is essential for any high-yield and robust practical applications. However, it has been very challenging to demonstrate such coupling while preserving the ultrahigh Q properties of the resonators. Here, we show how the silicon photonic platform can overcome this long-standing challenge. Silicon waveguides with appropriate designs enable efficient and strong coupling to these WGM electro-optic resonators. We discuss various integration architectures of these resonators onto a silicon chip and experimentally demonstrate critical coupling of a planar Si waveguide and an ultrahigh QLiTaO3 resonator (Q∼108). Our results show a promising path for widespread and practical applications of these resonators on a silicon photonic platform.

  6. A robust fibre laser system for electro-optic electron bunch profile measurements at FLASH

    Energy Technology Data Exchange (ETDEWEB)

    Wissmann, Laurens-Georg

    2012-08-15

    For the electro-optic measurement of electron bunch profiles at FLASH a robust ytterbium doped fibre laser (YDFL) system has been developed consisting of a laser oscillator and a two-staged amplifier. The oscillator is designed to meet the specifications of high reliability and low noise operation. The amplifier makes use of tailored nonlinearity to enhance the spectral bandwidth of the output laser pulses. Active repetition rate control enables sub-picosecond synchronisation of the laser to the accelerator reference RF. Using a two-stage gating scheme the output pulse train repetition rate is adopted to the accelerator repetition rate. An experimental site used for electro-optic electron bunch diagnostics has been redesigned to support single-shot bunch profile measurements based on spectral decoding. An existing bunch profile monitor with a similar laser system was upgraded and electro-optic bunch profile measurements were conducted, allowing for a comparison with measurements done with other longitudinal electron bunch diagnostics and with former measurements.

  7. Hybrid electro-optical nanosystem for neurons investigation

    Science.gov (United States)

    Miu, Mihaela; Kleps, Irina; Craciunoiu, Florea; Simion, Monica; Bragaru, Adina; Ignat, Teodora

    2010-11-01

    The scope of this paper is development of a new laboratory-on-a-chip (LOC) device for biomedical studies consisting of a microfluidic system coupled to microelectronic/optical transducers with nanometric features, commonly called biosensors. The proposed device is a hybrid system with sensing element on silicon (Si) chip and microfluidic system on polydimethylsiloxane (PDMS) substrates, taking into accounts their particular advantages. Different types of nanoelectrode arrays, positioned in the reactor, have been investigated as sensitive elements for electrical detection and the recording of neuron extracellular electric activity has been monitorized in parallel with whole-cell patch-clamp membrane current. Moreover, using an additional porosification process the sensing element became efficient for optical detection also. The preliminary test results demonstrate the functionality of the proposed design and also the fabrication technology, the devices bringing advantages in terms enhancement of sensitivity in both optoelectronic detection schemes.

  8. Electro-optical phenomena based on ionic liquids in an optofluidic waveguide.

    Science.gov (United States)

    He, Xiaodong; Shao, Qunfeng; Cao, Pengfei; Kong, Weijie; Sun, Jiqian; Zhang, Xiaoping; Deng, Youquan

    2015-03-01

    An optofluidic waveguide with a simple two-terminal electrode geometry, when filled with an ionic liquid (IL), forms a lateral electric double-layer capacitor under a direct current (DC) electric field, which allows the realization of an extremely high carrier density in the vicinity of the electrode surface and terminals to modulate optical transmission at room temperature under low voltage operation (0 to 4 V). The unique electro-optical phenomenon of ILs was investigated at three wavelengths (663, 1330 and 1530 nm) using two waveguide geometries. Strong electro-optical modulations with different efficiencies were observed at the two near-infrared (NIR) wavelengths, while no detectable modulation was observed at 663 nm. The first waveguide geometry was used to investigate the position-dependent modulation along the waveguide; the strongest modulation was observed in the vicinity of the electrode terminal. The modulation phase is associated with the applied voltage polarity, which increases in the vicinity of the negative electrode and decreases at the positive electrode. The second waveguide geometry was used to improve the modulation efficiency. Meanwhile, the electro-optical modulations of seven ILs were compared at an applied voltage ranging from ±2 V to ±3.5 V. The results reveal that the modulation amplitude and response speed increase with increasing applied voltage, as well as the electrical conductivity of ILs. Despite the fact that the response speed isn't fast due to the high ionic density of ILs, the modulation amplitude can reach up to 6.0 dB when a higher voltage (U = ±3.5 V) is applied for the IL [Emim][BF4]. Finally, the physical explanation of the phenomenon was discussed. The effect of the change in IL structure on the electro-optical phenomena was investigated in another new experiment. The results reveal that the electro-optical phenomenon is probably caused mainly by the change in carrier concentration (ion redistribution near charged

  9. Electro-optical properties of dislocations in silicon and their possible application for light emitters

    Energy Technology Data Exchange (ETDEWEB)

    Arguirov, Tzanimir Vladimirov

    2007-10-14

    This thesis addresses the electro-optical properties of silicon, containing dislocations. The work demonstrates that dislocation specific radiation may provide a means for optical diagnostics of solar cell grade silicon. It provides insight into the mechanisms governing the dislocation recombination activity, their radiation, and how are they influenced by other defects present in silicon. We demonstrate that photoluminescence mapping is useful for monitoring the recombination activity in solar cell grade silicon and can be applied for identification of contaminants, based on their photoluminescence signatures. It is shown that the recombination at dislocations is strongly influenced by the presence of metals at the dislocation sites. The dislocation radiation activity correlates with their electrical activity. It is shown that the dislocation and band-to-band luminescence are essentially anti-correlated. {beta}FeSi{sub 2} precipitates, with a luminescence at 0.8 eV, were detected within the grains of block cast materials. They exhibit a characteristic feature of quantum dots, namely blinking. The second aspect of the thesis concerns the topic of silicon based light emitters for on-chip optical interconnects. The goal is an enhancement of sub-band-gap or band-to-band radiation by controlled formation of dislocation-rich areas in microelectronics-grade silicon as well as understanding of the processes governing such enhancement. For light emitters based on band-to-band emission it is shown, that internal quantum efficiency of nearly 2 % can be achieved, but the emission is essentially generated in the bulk of the wafer. On the other hand, light emitters utilizing the emission from dislocation-rich areas of a well localized wafer depth were explored. Three different methods for reproducible formation of a dislocation-rich region beneath the wafer surface were investigated and evaluated in view of their room temperature sub-band-gap radiation: (1) silicon implantation

  10. Hydrogen bonding intermolecular effect on electro-optical response of doped 6PCH nematic liquid crystal with some azo dyes

    Science.gov (United States)

    Kiani, S.; Zakerhamidi, M. S.; Tajalli, H.

    2016-05-01

    Previous studies on the electro-optical responses of dye-doped liquid crystal have shown that dopant material have a considerable effect on their electro-optical responses. Despite the studies carried out on electro-optical properties of dye-doped liquid crystal, no attention has been paid to study of the interaction and structural effects in this procedure. In this paper, linear dyes and with similar structure were selected as dopants. The only difference in used dyes is the functional groups in their tails. So, doping of these dyes into liquid crystals determines the influence of interaction type on electro-optical behaviours of the doped systems. Therefore, in this work, two aminoazobenzene ("A-dye": hydrogen bond donor) and dimethyl-aminoazobenzene ("B-dye") dyes with different compositional percentages in liquid crystal host were used. Electro-optical Kerr behaviour, the pre-transition temperature and third order nonlinear susceptibility were investigated. The obtained results effectively revealed that type of interactions between the dye and liquid crystal is determinative of behavioral difference of doped system, compared to pure liquid crystal. Also, pre-transitional behaviour and thereupon Kerr electro-optical responses were affected by formed interactions into doped systems. In other words, it will be shown that addition of any dopants in liquid crystal, regardless of the nature of interactions, cannot cause appropriate electro-optical responses. In fact, type of dye, nature of interactions between dopant and liquid crystalline host as well as concentration of dye are the key factors in selecting the appropriate liquid crystal and dopant dye.

  11. Photoelectrochemistry of Electronic and Electro-Optical Materials

    Science.gov (United States)

    1992-09-01

    Etching of Blazed Echelle Gratings in n-GaAs", presented at the Fall Meeting of the Electrochemical Society , Chicago, IL, October 9-14, 1988. 3...SiC", Fall Meeting of the Electrochemical Society , Hollywood, FL, October 15-20, 1989. 5. "Morphology Control of Photoelectrochemically Etched...Profiles in n-GaAs", presented at the Fall Meeting of the Electrochemical Society , Hollywood, FL, October 15-20, 1989. 6. "The Evaluation of

  12. Architectures of electro-optical packet switched networks

    DEFF Research Database (Denmark)

    Berger, Michael Stubert

    2004-01-01

    and examines possible architectures for future high capacity networks with high capacity nodes. It is assumed that optics will play a key role in this scenario, and in this respect, the European IST research project DAVID aimed at proposing viable architectures for optical packet switching, exploiting the best......, Constraint Based Routing is examined, and the effect from taking the link load into account is evaluated. It is believed that electrical packet switching will satisfy demands in the coming years, and this work covers several aspects hereof. A new load balancing scheme for multipath packet switches...

  13. Actively stabilized wavelength-insensitive carrier elimination from an electro-optically modulated laser beam

    CERN Document Server

    Cooper, Nathan; Dunning, Alexander; Freegarde, Tim

    2012-01-01

    We demonstrate a simple and robust technique for removal of the carrier wave from a phase-modulated laser beam, using a non-interferometric method that is insensitive to the modulation frequency and instead exploits the polarization-dependence of electro-optic modulation. An actively stabilized system using feedback via a liquid crystal cell yields long-term carrier suppression in excess of 28 dB at the expense of a 6.5 dB reduction in sideband power.

  14. New Remote Gas Sensor Using Rapid Electro-Optical Path Switching

    Science.gov (United States)

    Sachse, G. W.; Lebel, P. J.; Wallio, H. A.; Vay, S. A.; Wang, L. G.

    1994-01-01

    Innovative gas filter correlation radiometer (GFCR) features nonmechanical switching of internal optical paths. Incoming radiation switched electro-optically, by means of polarization, between two optical paths, one of which contains correlation gas cell while other does not. Advantages include switching speed, 2 to 3 orders of magnitude faster than mechanical techniques, and high reliability. Applications include regional studies of atmospheric chemistry from either manned or unmanned aircraft as well as satellite studies of global distributions, sources and sink mechanisms for key species involved in chemistry of troposphere. Commercial applications: ability to survey many miles of natural gas pipelines rapidly from aircraft, pinpointing gas leaks by measuring methane at 2.3 micrometers.

  15. A polymer electro-optic modulator with ultra wide-band and low driving voltage

    Institute of Scientific and Technical Information of China (English)

    Kambiz Abedi; Habib Vahidi

    2011-01-01

    In this paper,a polymer electro optic modulator is designed and simulated using the full vectorial finite element method.First order edge elements are used in finite element implementation,and the finite element technique is used to obtain modulator response thoroughly.From the numerical analysis,frequency dispersions of modulator's important parameters,such as microwave effective index nm,microwave characteristic impedance Zt and microwave loss α,are extracted.Our design exhibits electrical bandwidth of 260 GHz and drive voltage of about 2.8 V·cm in this frequency.

  16. Thermally Stable Guest-Host Polyetherketone Poled Polymer for Electro-Optical Applications

    Institute of Scientific and Technical Information of China (English)

    潘奇伟; 房昌水; 秦志辉; 顾庆天; 吴祥雯; 史伟; 余金中

    2002-01-01

    The high glass transition temperature polymer polyetherketone doped with disperse red 13 (DR13/PEK-c) has been prepared by the spin-coating method. Through in situ second-harmonic generation, the corona poling temperature was optimized by measuring the temperature dependence of the in situ second-harmonic generation signal intensity under the poling electric field. The linear electro-optic coefficients of the poled polymer films have been determined at 632.8nm by using a simple interferometric technique. The polymer system was measured after 13000h, and found that it remained at 80% of its initial value.

  17. Electro-optic sampling of THz pulses at the CTR source at FLASH

    Energy Technology Data Exchange (ETDEWEB)

    Wunderlich, Steffen

    2012-06-15

    Several applications in material science, non-linear optics and solid-state physics require short pulses with a high pulse energy of radiation in the far-infrared and in the terahertz (THz) regime in particular. As described in the following, coherent transition radiation generated by high-relativistic electron bunches at FLASH provides broadband single-cycle pulses of sub-picosecond length. The pulses are characterized using the quantitative and time-resolved technique of electro-optic sampling showing peak field strengths in the order of 1 MV/cm.

  18. Theory of Electro-optic Modulation via a Quantum Dot Coupled to a Nano-resonator

    CERN Document Server

    Majumdar, Arka; Faraon, Andrei; Vuckovic, Jelena

    2009-01-01

    In this paper, we analyze the performance of an electro-optic modulator based on a single quantum dot strongly coupled to a nano-resonator, where electrical control of the quantum dot frequency is achieved via quantum confined Stark effect. Using realistic system parameters, we show that modulation speeds of a few tens of GHz are achievable with this system, while the energy per switching operation can be as small as 0.5 fJ. In addition, we study the non-linear distortion, and the effect of pure quantum dot dephasing on the performance of the modulator.

  19. Time-Resolved Terahertz Spectroscopy with Free-Space Electro-Optic Sampling

    Institute of Scientific and Technical Information of China (English)

    ZHANG Liang-Liang; ZHAO Guo-Zhong; ZHONG Hua; HU Ying; ZHANG Cun-Lin

    2004-01-01

    @@ We present a time-resolved ultrafast measurement in terahertz (THz) frequency region by means of the free-space electro-optic sampling. The fast delay scan technique is used to suppress the noise with low frequency and to improve the signal-to-noise ratio of the system. The transmission spectra of different materials are obtained.The optical properties of these materials in a THz region are shown. The broadening of spectrum and chirping phenomena are illustrated. We find that polystyrene is an excellent material for the THz application.

  20. The precision analysis of continuous zoom lens in airborne electro-optical pod

    Science.gov (United States)

    Yang, Xiao-xu; Li, Da-wei; Han, Jun-feng; Dong, Qiang; Huang, Wei; Wei, Yu

    2014-02-01

    In the research of electro-optical pod, this paper propose a mission requirements that continuous zoom lens system is using for measuring angle in the process. This paper analyzes the influence of angle measurement accuracy from focal length and optical axis errors in the process of continuous zoom, and given the mathematical model of the influence of angle measurement accuracy. The simulation analysis indicated that Angle measuring accuracy is affected by the process of continuous zoom. The simulation analysis results have certain instructive significance to engineering practice.

  1. 40 GHz electro-optic modulation in hybrid silicon-organic slotted photonic crystal waveguides.

    Science.gov (United States)

    Wülbern, Jan Hendrik; Prorok, Stefan; Hampe, Jan; Petrov, Alexander; Eich, Manfred; Luo, Jingdong; Jen, Alex K-Y; Jenett, Martin; Jacob, Arne

    2010-08-15

    In this Letter we demonstrate broadband electro-optic modulation with frequencies of up to 40 GHz in slotted photonic crystal waveguides based on silicon-on-insulator substrates covered and infiltrated with a nonlinear optical polymer. Two-dimensional photonic crystal waveguides in silicon enable integrated optical devices with an extremely small geometric footprint on the scale of micrometers. The slotted waveguide design optimizes the overlap of the optical and electric fields in the second-order nonlinear optical medium and, hence, the interaction of the optical and electric waves.

  2. Field-effect active plasmonics for ultracompact electro-optic switching

    OpenAIRE

    Müstecaplıoğlu, Özgür E.; Çetin, Arif E.; Yanık, Ahmet A.; Mertiri, Alket; Erramilli, Shyamsunder; Altuğ, Hatice

    2012-01-01

    Field-effect active plasmonics for ultracompact electro-optic switching Arif E. Çetin, Ahmet A. Yanik, Alket Mertiri, Shyamsunder Erramilli, Özgür E. Müstecaplolu, and Hatice Altug Citation: Applied Physics Letters 101, 121113 (2012); doi: 10.1063/1.4754139 View online: http://dx.doi.org/10.1063/1.4754139 View Table of Contents: http://scitation.aip.org/content/aip/journal/apl/101/12?ver=pdfcov Published by the AIP Publishing Articles you may be interested in A proposal f...

  3. Mid-infrared dual-comb spectroscopy with electro-optic modulators

    CERN Document Server

    Yan, Ming; Iwakuni, Kana; Millot, Guy; Hänsch, Theodor W; Picqué, Nathalie

    2016-01-01

    We demonstrate dual-comb spectroscopy based on difference frequency generation of frequency-agile near-infrared frequency combs, produced with the help of electro-optic modulators. The combs have a remarkably flat intensity distribution and their positions and line spacings can be selected freely by simply dialing a knob. We record, in the 3-micron region, Doppler-limited absorption spectra with resolved comb lines within milliseconds. Precise molecular line parameters are retrieved. Our technique holds promise for fast and sensitive time-resolved studies e.g. of trace gases.

  4. Characteristics of Electro-Optic Device Using Conducting Polymers, Polythiophene and Polypyrrole Films

    Science.gov (United States)

    Kaneto, Keiichi; Yoshino, Katsumi; Inuishi, Yoshio

    1983-07-01

    Detailed characteristics of electro-optic elements (color switching and memory) utilizing the spectral change of conducting polymers by electrochemical doping and undoping are studied. The response time of color switching, for example, red≤ftrightarrowblue in polythiophene film in the electrolyte of LiBF4/acetonitrile is 30˜100 msec under the applied voltages of -2.0{≤ftrightarrow}+4.0 V vs. Li plate. More than 103 cycles of color switch are observed quite reproducibly. Three color states of yellow green, dark brown and blue are demonstrated for polypyrrole film.

  5. Graphene photonics for resonator-enhanced electro-optic devices and all-optical interactions

    Science.gov (United States)

    Englund, Dirk R.; Gan, Xuetao

    2017-03-21

    Techniques for coupling light into graphene using a planar photonic crystal having a resonant cavity characterized by a mode volume and a quality factor and at least one graphene layer positioned in proximity to the planar photonic crystal to at least partially overlap with an evanescent field of the resonant cavity. At least one mode of the resonant cavity can couple into the graphene layer via evanescent coupling. The optical properties of the graphene layer can be controlled, and characteristics of the graphene-cavity system can be detected. Coupling light into graphene can include electro-optic modulation of light, photodetection, saturable absorption, bistability, and autocorrelation.

  6. Orientational dynamics in dye-doped organic electro-optic materials

    DEFF Research Database (Denmark)

    Apitz, D.; Svanberg, C.; Jespersen, K.G.

    2003-01-01

    The time dependent birefringence of polymer-based electro-optic materials is investigated using ellipsometry. We show that the birefringence after switching off the poling field does not depend only on the induced refractive index, but also on how that level was reached. The role of the poling...... voltage and poling time is discussed in turn-on and turn-off experiments and an original curve-fit function is introduced. We also propose a schematic model of the polymer dynamics in the system, which is consistent with complementary dielectric measurements. © 2003 American Institute of Physics. © 2003...

  7. Precursor polymer approach towards functional conjugated polymer networks and ultrathin film electro-optical applications

    Science.gov (United States)

    Taranekar, Prasad

    Conjugated polymers are organic semiconductors which are of interest to a wide variety of optical, electronic, opto-electronic, and sensory applications; including light emitting diodes, thin film transistors, photovoltaic cells, and chemical sensors. While conducting polymers have some similarities to conventional polymeric materials, it is clearly the extensive main chain pi-conjugated structure and its implicit electro-optical properties that make it distinct. The same structure, however, gives it "chain stiffness" that affects its physical behavior. As a direct consequence of this, virtually all unsubstituted conducting polymers are found to be intractable and insoluble. This dissertation details the issue of tailoring the electro-optical properties and processability of conjugated polymers via a novel "precursor polymer approach". In this approach, electroactive side group units of either similar or different kind are tethered to a polymeric backbone. This combination determines the eventual electro-optical and electrochemical properties of these polymers including their ability to form ultrathin films. Thus, the desired macroscopic property is transformed by designing new precursor polymer structures, manipulating polymer-based compositions and blends, and the exploration and exploitation of their electrochemical processing conditions. In Chapters 2, 3, and 4, we have used single or binary electroactive compositions of species such as pyrrole, thiophene, carbazole and terthiophene are tethered to a linear polymeric backbone. Besides, the linear approach, in Chapters 5 and 6, we have also explored the use of generational dendrimers as backbone with carbazole units attached as peripheral electroactive groups. These precursor polymers were then subjected to electrochemical cross-linking to generate high optical quality ultrathin films on a conducting substrate such as indium tin oxide (ITO) or Au surfaces. The reaction of such electroactive species inimically

  8. Graphene photonics for resonator-enhanced electro-optic devices and all-optical interactions

    Energy Technology Data Exchange (ETDEWEB)

    Englund, Dirk R.; Gan, Xuetao

    2017-03-21

    Techniques for coupling light into graphene using a planar photonic crystal having a resonant cavity characterized by a mode volume and a quality factor and at least one graphene layer positioned in proximity to the planar photonic crystal to at least partially overlap with an evanescent field of the resonant cavity. At least one mode of the resonant cavity can couple into the graphene layer via evanescent coupling. The optical properties of the graphene layer can be controlled, and characteristics of the graphene-cavity system can be detected. Coupling light into graphene can include electro-optic modulation of light, photodetection, saturable absorption, bistability, and autocorrelation.

  9. Development of laser marking system with electro-optic Q-switch

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Cheol Jung; Kim, Jeong Moog; Kim, Kwang Suk; Park, Seung Kyu; Baik, Sung Hoon

    1995-11-01

    We developed a high repetition electro-optic Q switch Nd:YAG laser and scan system for laser marking. We localized the scan mirrors and their mounts. We made the database for the optical properties of commercial flat-field lenses with our optics design software. We fabricated the detailed network between the galvanometer based beam scanning system and the laser generator. To accelerate the commercialization by the joint company, the training and transfer of technology were pursued in the joint participation by company researchers from the early stage. (author). 8 refs., 6 tabs., 27 figs.

  10. Silicon-on-Insulator Based Electro-optic Variable Optical Attenuator with a Series Structure

    Institute of Scientific and Technical Information of China (English)

    HE Yue-Jiao; LI Fang; LIU Yu-Liang

    2005-01-01

    An electro-optic variable optical attenuator in silicon-on-insulator is designed and fabricated. A series structure is used to improve the device efficiency. Compared to the attenuator in the single p-i-n diode structure in the same modulating length, the attenuation range of the device in the series structure improves 2-3 times in the same injecting current density, while the insertion loss is not affected. The maximum dynamic attenuation of the device is greater than 30dB. The response frequency is obtained to be about 2MHz.

  11. ElectroOptical measurements of ultrashort 45 MeV electron beam bunch

    CERN Document Server

    Nikas, D; Kowalski, L A; Larsen, R; Lazarus, D M; Ozben, C; Semertzidis, Y K; Tsang, Thomas; Srinivasan-Rao, T

    2001-01-01

    We have made an observation of 45 MeV electron beam bunches using the nondestructive electro-optical (EO) technique. The amplitude of the EO modulation was found to increase linearly with electron beam charge and decrease inversely with the optical beam path distance from the electron beam. The risetime of the signal was bandwidth limited by our detection system to \\~70ps. An EO signal due to ionization caused by the electrons traversing the EO crystal was also observed. The EO technique may be ideal for the measurement of bunch structure with femtosecond resolution of relativistic charged particle beam bunches.

  12. Invariant electro-optical system for deflection measurement of floating docks

    Science.gov (United States)

    Gorbachev, Alexey A.; Hoang, Anh Phuong

    2017-06-01

    An electro-optical system for deflection measurement of floating docks is represented in this paper. This system contains a base unit with two measurement channels observing opposite directions of the dock. It also includes a set of reference marks and an industrial computer. The measurement unit contains of a camera with long focal-length lens and a beam splitter. The effect of the beam splitter turning point on the image position of the reference mark on the camera is analyzed as well in this paper.

  13. A deterministic guide for material and mode dependence of on-chip electro-optic modulator performance

    Science.gov (United States)

    Amin, Rubab; Suer, Can; Ma, Zhizhen; Sarpkaya, Ibrahim; Khurgin, Jacob B.; Agarwal, Ritesh; Sorger, Volker J.

    2017-10-01

    Electro-optic modulation is a key function in optical data communication and possible future optical computing engines. The performance of modulators intricately depends on the interaction between the actively modulated material and the propagating waveguide mode. While high-performing modulators were demonstrated before, the approaches were taken as ad-hoc. Here we show the first systematic investigation to incorporate a holistic analysis for high-performance and ultra-compact electro-optic modulators on-chip. We show that intricate interplay between active modulation material and optical mode plays a key role in the device operation. Based on physical tradeoffs such as index modulation, loss, optical confinement factors and slow-light effects, we find that bias-material-mode regions exist where high phase modulation and high loss (absorption) modulation is found. This work paves the way for a holistic design rule of electro-optic modulators for on-chip integration.

  14. Measurement of Frequency Shift Characteristics Based on LiNbO3 Waveguide Electro-Optic Intensity Modulator

    Institute of Scientific and Technical Information of China (English)

    Zhou Meng; Hui-Juan Zhou; Yi Liao; Qiong Yao

    2008-01-01

    High-speed and wide-band LiNbO3 waveguide electro-optic intensity modulator has drawn great attention in the field of optical fiber communi-cation and sensor. This paper reports the research results on the measurement of frequency shift character-istics of Mach-Zehnder electro-optic intensity modulator. Two measurement methods of frequency shift character-istics for high and low frequency modulations are studied in theory and experiment and demonstrate different results. The realization of a multi-wavelength optical source based on Mach-Zehnder electro-optic intensity modulator has been introduced. The technique to reach the maximum intensity for interesting shift frequency, particularly for heterodyne detection of Brillouin distributed optical fiber sensing, has been given.

  15. High-Speed Electro-Optic Modulator Integrated with Graphene-Boron Nitride Heterostructure and Photonic Crystal Nanocavity

    CERN Document Server

    Gao, Yuanda; Gan, Xuetao; Li, Luozhou; Peng, Cheng; Meric, Inanc; Wang, Lei; Szep, Attila; Walker, Dennis; Hone, James; Englund, Dirk

    2014-01-01

    Nanoscale and power-efficient electro-optic (EO) modulators are essential components for optical interconnects that are beginning to replace electrical wiring for intra- and inter-chip communications. Silicon-based EO modulators show sufficient figures of merits regarding device footprint, speed, power consumption and modulation depth. However, the weak electro-optic effect of silicon still sets a technical bottleneck for these devices, motivating the development of modulators based on new materials. Graphene, a two-dimensional carbon allotrope, has emerged as an alternative active material for optoelectronic applications owing to its exceptional optical and electronic properties. Here, we demonstrate a high-speed graphene electro-optic modulator based on a graphene-boron nitride (BN) heterostructure integrated with a silicon photonic crystal nanocavity. Strongly enhanced light-matter interaction of graphene in a submicron cavity enables efficient electrical tuning of the cavity reflection. We observe a modul...

  16. H-infinity mix sensitivity controller design based on GIMC for electro-optical stabilization and tracking system

    Science.gov (United States)

    Liu, Zi-dong; Bao, Qi-liang; Xia, Yunxia; Liu, Xiang

    2013-08-01

    Electro-optical stabilization and tracking system is critical and difficult issue in satellite laser communication. Moreover, line-of-sight stabilized system is the kernel of implementing electro-optical stabilization and tracking system, which can be used to isolate the vibration of the moving platform of the satellite and the disturbance of the space environment. In this paper, we propose a new method, which using H∞ mix sensitivity based on generalized internal model controller (GIMC), to design the control system of the electro-optical stabilized platform. It is well known that there is an intrinsic conflict between performance and robustness in the standard feedback framework. Generalized internal model controller is a new architecture which can separate the performance and robustness design in controller design. This architecture has two parts: a high performance controller, say K0,which is designed by PI controller in this paper, and then a robustification controller, say Q, which is designed to improve the ability of the anti disturbance by using H-infinity mix sensitivity controller design method. In this paper, we also present the steps of controller design by using this method to make it easier to use. Based on the proposed method, numerical simulation and experiment are both carried out for a gyro stabilized platform of electro-optical tacking system. Both the numerical simulated and the experimental results show that the electro-optical stabilized platform using the H-infinity mix sensitivity controller design method based on GIMC is accurate and effective. Comparing with the same PI controller in standard feedback framework, the proposed method can guarantee the high tracking performance as same as the PI controller and improve the external disturbance restraining ability a lot. In conclusion, H-infinity mix sensitivity controller design method based on GIMC is a new approach for gyro stabilized platform of electro-optical stabilization and tracking

  17. Improved performance of traveling wave directional coupler modulator based on electro-optic polymer

    CERN Document Server

    Zhang, Xingyu; Lin, Che-yun; Wang, Alan X; Hosseini, Amir; Lin, Xiaohui; Chen, Ray T

    2014-01-01

    Polymer based electro-optic modulators have shown great potentials in high frequency analog optical links. Existing commercial LiNibO3 Mach-Zehnder modulators have intrinsic drawbacks in linearity to provide high fidelity communication. In this paper, we present the design, fabrication and characterization of a traveling wave directional coupler modulator based on electro-optic polymer, which is able to provide high linearity, high speed, and low optical insertion loss. A silver ground electrode is used to reduce waveguide sidewall roughness due to the scattering of UV light in photolithography process in addition to suppressing the RF loss. A 1-to-2 multi-mode interference 3dB-splitter, a photobleached refractive index taper and a quasi-vertical taper are used to reduce the optical insertion loss of the device. The symmetric waveguide structure of the MMI-fed directional coupler is intrinsically bias-free, and the modulation is obtained at the 3-dB point regardless of the ambient temperature. By achieving lo...

  18. The structural and electro-optical characteristics of AZO/Cr:Cu/AZO transparent conductive film

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Tien-Chai [Department of Electrical Engineering, Kun Shan University, No. 195, Kun-Da Road, Yung-Kang Dist., Tainan 71003, Taiwan, ROC (China); Huang, Wen-Chang, E-mail: wchuang@mail.ksu.edu.tw [Department of Electro-Optical Engineering, Kun Shan University, No. 195, Kun-Da Road, Yung-Kang Dist., Tainan 71003, Taiwan, ROC (China); Tsai, Fu-Chun [Department of Electro-Optical Engineering, Kun Shan University, No. 195, Kun-Da Road, Yung-Kang Dist., Tainan 71003, Taiwan, ROC (China)

    2015-08-31

    A novel triple-layered transparent conductive film, AZO/Cr:Cu/AZO (ACCA), was presented in the paper. The structural and electro-optical properties of the ACCA film were discussed. The thickness of the middle metal layer was constant and those of the AZO layers were varied. The ACCA film shows an obvious ZnO (002) c-axis preferential growth. No diffraction peaks related to Cr and Cu were observed through x-ray diffraction analysis. The middle Cr:Cu layer showed a thickness of 8.16 nm with a continuous and amorphous structure by the observation of a high-resolution transmission electron microscopy (HR-TEM). For the electro-optical characteristic, a best figure of merit (FOM) value of 3.54 × 10{sup −3} Ω{sup −1} with a corresponding transmittance of 85% was obtained at the thickness of 116 nm of ACCA film. The high FOM value of the film is due to the improvement of conductivity and small sacrifices of transparency. - Highlights: • A novel triple-layered transparent conductive film, AZO/Cr:Cu/AZO is developed. • Chromium is added to copper to reduce the oxidation–reduction reaction. • The film has a FOM of 3.54 × 10{sup −3} Ω{sup −1} with a corresponding transmittance of 85%. • The Cr:Cu layer shows a continuous and amorphous structure.

  19. High sensitivity photonic time-stretch electro-optic sampling of terahertz pulses

    CERN Document Server

    Szwaj, Christophe; Parquier, Marc Le; Roy, Pascale; Manceron, Laurent; Brubach, Jean-Blaise; Tordeux, Marie-Agnès; Bielawski, Serge

    2016-01-01

    Single-shot recording of terahertz electric signals has recently become possible at high repetition rates, by using the photonic time-stretch electro-optic sampling (EOS) technique. However the moderate sensitivity of time-stretch EOS is still a strong limit for a range of applications. Here we present a variant enabling to increase the sensitivity of photonic time-stretch for free-propagating THz signals. A key point is to integrate the idea presented in Ref. [Ahmed et al., Rev. Sci. Instrum. 85, 013114 (2014)], for upgrading classical time-stretch systems. The method is tested using the high repetition rate terahertz coherent synchrotron radiation source (CSR) of the SOLEIL synchrotron radiation facility. The signal-to-noise ratio of our terahertz digitizer could thus be straightforwardly improved by a factor $\\approx 6.5$, leading to a noise-equivalent input electric field below $1.25$~V/cm inside the electro-optic crystal, over the 0-300~GHz band (i.e, 2.3~$\\mu$V/cm/$\\sqrt{\\text{Hz}}$). The sensitivity is...

  20. Impact of lateral carrier confinement on electro-optical tuning properties of polariton condensates

    Energy Technology Data Exchange (ETDEWEB)

    Brodbeck, S.; Suchomel, H.; Amthor, M.; Wolf, A.; Kamp, M. [Technische Physik, Physikalisches Institut and Wilhelm Conrad Röntgen-Research Center for Complex Material Systems, Universität Würzburg, Am Hubland, D-97074 Würzburg (Germany); Schneider, C. [Technische Physik, Physikalisches Institut and Wilhelm Conrad Röntgen-Research Center for Complex Material Systems, Universität Würzburg, Am Hubland, D-97074 Würzburg (Germany); Mediterranean Institute of Fundamental Physics, Via Appia Nuova 31, 00040 Rome (Italy); Höfling, S. [Technische Physik, Physikalisches Institut and Wilhelm Conrad Röntgen-Research Center for Complex Material Systems, Universität Würzburg, Am Hubland, D-97074 Würzburg (Germany); SUPA, School of Physics and Astronomy, University of St. Andrews, St. Andrews KY 16 9SS (United Kingdom)

    2015-07-27

    Electro-optical measurements on exciton-polaritons below and above the condensation threshold are performed on high quality, pin-doped microcavities with embedded GaAs quantum wells. Applying an external electric field shifts the polariton emission by hundreds of μeV both in the linear and the nonlinear regime. We study three device geometries to investigate the influence of carrier confinement in the plane of the quantum well on the electro-optical tuning properties. In the conventional micropillar geometry, the electric field tuning behavior is dominated by the effects of carrier tunneling and electric field screening that manifest in a blueshift of the polariton emission. In stark contrast, for a planar sample geometry, we can significantly extend the range of electric fields and a redshift is observed. To separate the contributions of quantum confined Stark effect and reduced exciton oscillator strength to the energy shift, we study a third sample where the etching of micropillars is stopped just above the active region. In this semi-planar geometry, exciton and polariton emissions can be measured simultaneously. As for the planar geometry, redshifts of the polariton emission are observed below and above threshold that are well reproduced by theoretical shifts.

  1. Electro-optic and Many-body Effects on Optical Absorption of Twisted Bilayer Graphene

    Science.gov (United States)

    Lee, Kan-Heng; Huang, Lujie; Kim, Cheol-Joo; Park, Jiwoong

    2015-03-01

    In twisted bilayer graphene (tBLG), the interlayer rotation angle between the two graphene layers induces additional angle-dependent van Hove singularities (vHSs) in its band structure where the two Dirac cones from each layer intersect. These vHSs introduce extra angle-dependent absorption peaks in the optical absorption spectra of tBLG. Here, we experimentally investigate the effects of the overall doping and the interlayer potential on these interlayer absorption features at various angles. We independently tune the doping concentration of each layer with a newly-developed, optically transparent, dual-gate transistor geometry to perform simultaneous optical and electrical measurements. Our data show strong electro-optic phenomena in the optical absorption of tBLG: the peak energy and width of the interlayer resonance feature sensitively depends on the overall doping and interlayer potential. We explain our observation using a simple band picture as well as many-body effects. Our study provides a powerful experimental platform for studying more complicated structures such as rotated tri- and multi-layer graphene systems in the future. Moreover, the understanding of electro-optic and many-body effects in these materials opens up a way for novel electrochromic devices.

  2. Analysis of electro-optic switches with series-coupled multiple microring resonators

    Institute of Scientific and Technical Information of China (English)

    YAN Xin; MA Chun-sheng; ZHENG Chuan-tao; WANG Xian-yin; ZHANG Da-ming

    2009-01-01

    In terms of the coupled mode theory, microring resonance and electro-optic modulation princeple, a reasonable project is proposed for designing an electro-optic switch with the series-coupled multiple microring resonators. The simulation and optimization are performed at the resonant wavelength of 1550 nm. The results are as follows: the core size of the microring is 1.6 μm×1.6 μm, the confined layer between the core and the electrode is 1.6 μm, the thickness of the electrode is 0.15 μm, the radius ofthe microring is 15.2 μm, the coupling gap between the microring and the channel is 0.14 μm, and the one between the microring and the microring is 0.6 μm, microring number M is 4, the switching voltage is 4 V, the insertion loss is 5.4 dB, and the crosstalk is -20 dB. The output spectrum is much flatter and much steeper than that of the single microring.

  3. Electro-optic properties of indium/erbium-codoped lithium niobate crystal for integrated optics

    Science.gov (United States)

    Du, Wan-Ying; Zhang, Zi-Bo; Ren, Shuai; Wong, Wing-Han; Yu, Dao-Yin; Pun, Edwin Yue-Bun; Zhang, De-Long

    2017-02-01

    Clamped and unclamped electro-optic coefficients γ13 and γ33 of In3+/Er3+-codoped LiNbO3 crystals, which were grown by Czochralski method from the melts containing 0.5 mol% Er2O3 while varied In2O3 contents of 0.0, 0.5, 1.0 and 1.5 mol%, were measured by Mach-Zehnder interferometry. The results show that In3+/Er3+ codoping does not cause change of γ13 and γ33, and both γ13 and γ33 can be regarded as unchanged in the studied In3+ concentration range of 0-2.6 mol% (in crystal) within the experimental error of 3%. The small doping effect is desired in light of the electro-optic application of the crystal. A qualitative, comprehensible explanation for the small effect is given on the basis of the EO coefficient model of LiNbO3 and doping effect on the defect structure of LiNbO3.

  4. Performance of an electro-optical solar compass in partially obscured Sun conditions.

    Science.gov (United States)

    Bollanti, S; De Meis, D; Di Lazzaro, P; Flora, F; Gallerano, G P; Mezi, L; Murra, D; Vicca, D

    2016-04-20

    Solar compasses are designed to accurately find true North on sunny days. However, no data on their performance are available when sunlight is partially blocked, e.g., by a cloud. We have measured, for the first time to the best of our knowledge, the performance of one of the most accurate electro-optical solar compasses (accuracy better than 0.01  deg) as a function of the solar disk obscuration during the Sun's eclipse on 20 March 2015. The measurements show that the accuracy level is mainly dependent on the asymmetry of the obscuration with respect to the main axis of the optical detection system and, to a lesser extent, on the percentage of the solar disk covered. In particular, azimuth measurement suffered a maximum deviation of 0.08 deg when 35% of the solar disk was asymmetrically obscured. The deviation was smaller when 46% of the solar disk was more symmetrically obscured. This experiment demonstrates that, even in the case of a partially obscured Sun, the electro-optical solar compass maintains an accuracy better than magnetic and electronic compasses.

  5. Synthesis and characterization of cross-linkable polyurethane-imide electro-optic waveguide polymer

    Science.gov (United States)

    Wang, Long-De; Tang, Jie; Li, Ruo-Zhou; Zhang, Tong; Tong, Ling; Tang, Jing

    2016-01-01

    The novel electro-optic (EO) polymers of fluorinated cross-linkable polyurethane-imides (CLPUI) were designed and synthesized by polycondensation of azo chromophore C1 and C2, diisocyanate MDI, and aromatic dianhydride 6FDA. Molecular structural characterization for the resulting polymers was achieved by 1HNMR, FT-IR, elemental analysis, and gel permeation chromatography. The polymers exhibit good film-forming properties, high glass transition temperature ( T g) in the range of 193-200 °C, and thermal stability up to 290 °C. The polymers that possess a high EO coefficient (γ_{33} = 48 and 56 pm/V) at 1550 nm for poled polymer thin films were measured by the simple reflection technique. Excellent temporal stability and low optical losses in the range of 1.1-1.7 dB/cm at 1550 nm were observed for these polymers. Using the synthesized side-chain electro-optic CLPUI as the active core material and of a fluorinated polyimide as cladding material, we have designed and successfully fabricated the high-performance polymer waveguide Mach-Zehnder EO modulators.

  6. High sensitivity photonic time-stretch electro-optic sampling of terahertz pulses

    Science.gov (United States)

    Szwaj, C.; Evain, C.; Le Parquier, M.; Roy, P.; Manceron, L.; Brubach, J.-B.; Tordeux, M.-A.; Bielawski, S.

    2016-10-01

    Single-shot recording of terahertz electric signals has recently become possible at high repetition rates, by using the photonic time-stretch electro-optic sampling (EOS) technique. However the moderate sensitivity of time-stretch EOS is still a strong limit for a range of applications. Here we present a variant enabling to increase the sensitivity of photonic time-stretch for free-propagating THz signals. The ellipticity of the laser probe is enhanced by adding a set of Brewster plates, as proposed by Ahmed et al. [Rev. Sci. Instrum. 85, 013114 (2014)] in a different context. The method is tested using the high repetition rate terahertz coherent synchrotron radiation source of the SOLEIL synchrotron radiation facility. The signal-to-noise ratio of our terahertz digitizer could thus be straightforwardly improved by a factor ≈6.5, leading to a noise-equivalent input electric field below 1.25 V/cm inside the electro-optic crystal, over the 0-300 GHz band (i.e., 2.3 μ V / cm / √{ Hz } ). The sensitivity is scalable with respect to the available laser power, potentially enabling further sensitivity improvements when needed.

  7. Sol-Gel Material-Enabled Electro-Optic Polymer Modulators.

    Science.gov (United States)

    Himmelhuber, Roland; Norwood, Robert A; Enami, Yasufumi; Peyghambarian, Nasser

    2015-07-27

    Sol-gels are an important material class, as they provide easy modification of material properties, good processability and are easy to synthesize. In general, an electro-optic (EO) modulator transforms an electrical signal into an optical signal. The incoming electrical signal is most commonly information encoded in a voltage change. This voltage change is then transformed into either a phase change or an intensity change in the light signal. The less voltage needed to drive the modulator and the lower the optical loss, the higher the link gain and, therefore, the better the performance of the modulator. In this review, we will show how sol-gels can be used to enhance the performance of electro-optic modulators by allowing for designs with low optical loss, increased poling efficiency and manipulation of the electric field used for driving the modulator. The optical loss is influenced by the propagation loss in the device, as well as the losses occurring during fiber coupling in and out of the device. In both cases, the use of sol-gel materials can be beneficial due to the wide range of available refractive indices and low optical attenuation. The influence of material properties and synthesis conditions on the device performance will be discussed.

  8. Single-shot electron bunch length measurements using a spatial electro-optical autocorrelation interferometer.

    Science.gov (United States)

    Sütterlin, Daniel; Erni, Daniel; Schlott, Volker; Sigg, Hans; Jäckel, Heinz; Murk, Axel

    2010-10-01

    A spatial, electro-optical autocorrelation (EOA) interferometer using the vertically polarized lobes of coherent transition radiation (CTR) has been developed as a single-shot electron bunch length monitor at an optical beam port downstream the 100 MeV preinjector LINAC of the Swiss Light Source. This EOA monitor combines the advantages of step-scan interferometers (high temporal resolution) [D. Mihalcea et al., Phys. Rev. ST Accel. Beams 9, 082801 (2006) and T. Takahashi and K. Takami, Infrared Phys. Technol. 51, 363 (2008)] and terahertz-gating technologies [U. Schmidhammer et al., Appl. Phys. B: Lasers Opt. 94, 95 (2009) and B. Steffen et al., Phys. Rev. ST Accel. Beams 12, 032802 (2009)] (fast response), providing the possibility to tune the accelerator with an online bunch length diagnostics. While a proof of principle of the spatial interferometer was achieved by step-scan measurements with far-infrared detectors, the single-shot capability of the monitor has been demonstrated by electro-optical correlation of the spatial CTR interference pattern with fairly long (500 ps) neodymium-doped yttrium aluminum garnet (Nd:YAG) laser pulses in a ZnTe crystal. In single-shot operation, variations of the bunch length between 1.5 and 4 ps due to different phase settings of the LINAC bunching cavities have been measured with subpicosecond time resolution.

  9. Sol-Gel Material-Enabled Electro-Optic Polymer Modulators

    Directory of Open Access Journals (Sweden)

    Roland Himmelhuber

    2015-07-01

    Full Text Available Sol-gels are an important material class, as they provide easy modification of material properties, good processability and are easy to synthesize. In general, an electro-optic (EO modulator transforms an electrical signal into an optical signal. The incoming electrical signal is most commonly information encoded in a voltage change. This voltage change is then transformed into either a phase change or an intensity change in the light signal. The less voltage needed to drive the modulator and the lower the optical loss, the higher the link gain and, therefore, the better the performance of the modulator. In this review, we will show how sol-gels can be used to enhance the performance of electro-optic modulators by allowing for designs with low optical loss, increased poling efficiency and manipulation of the electric field used for driving the modulator. The optical loss is influenced by the propagation loss in the device, as well as the losses occurring during fiber coupling in and out of the device. In both cases, the use of sol-gel materials can be beneficial due to the wide range of available refractive indices and low optical attenuation. The influence of material properties and synthesis conditions on the device performance will be discussed.

  10. Measurement of z-axis deviation angle of electro-optic crystal by conoscopic interference

    Science.gov (United States)

    Li, Dong; Liu, Yong; Liu, Xu; Jiang, Hongzhen; Zheng, Fanglan

    2016-09-01

    Properties of plasma electrode pockels cell is directly affected by the Z-axis deviation angle of the electro-optic crystal. Therefore, high precision measurement of the Z-axis deviation angle is indispensable. By using conoscopic interference technique, a measurement system for Z-axis deviation angle of electro-optic crystal is introduced. The principle of conoscopic interference method is described in detail, and a series of techniques are implied in this measurement system to improve the accuracy. High-precision positioning method of the crystal based on Michelson interference is proposed to determine the normal consistency of crystal, which can ensure the high positioning repeatability of crystal in the measurement process. The positioning comparison experiment of the crystal shows that the standard deviation of our method is less than 1pixel, which is much better than the traditional method (nearly 4pixels). Moreover, melatope extraction algorithm of optical axis based on image matching technique is proposed to ensure the melatope can be extracted in high precision. Calibration method of the normal of transmission surface of crystal is also proposed. The experiment results show that the PV and rms of Z-axis deviation angle is less than 0.05mrad and 0.02mrad, respectively. The repeatability accuracy is less than 0.01mrad.

  11. Polymer Electro-optic Modulator Linear Bias Using the Thermo-optic Effect

    Institute of Scientific and Technical Information of China (English)

    SUN Xiao-Qiang; CHEN Chang-Ming; LI Xiao-Dong; WANG Xi-Bin; YANG Tian-Fu; ZHANG Da-Ming; WANG Fei; XIE Zhi-Yuan

    2012-01-01

    A quasi-rectangular waveguide polymer Mach-Zehnder (M-Z) electro-optic (EO) modulator based on an organic/inorganic hybrid material with thermal bias control is fabricated and demonstrated. Linear bias for the modulator is obtained through thermo-optic effect. The optical output is adjusted by changing phase difference between the two arms of the M-Z interferometer. A power consumption of 16.1 mW for π phase change is observed owing to the application of silica cladding. This approach is proved to be effective to suppress direct current drift in polymer EO modulators.%A quasi-rectangular waveguide polymer Mach-Zehnder (M-Z) electro-optic (EO) modulator based on an organic/inorganic hybrid material with thermal bias control is fabricated and demonstrated.Linear bias for the modulator is obtained through thermo-optic effect.The optical output is adjusted by changing phase difference between the two arms of the M-Z interferometer.A power consumption of 16.1 m W for π phase change is observed owing to the application of silica cladding.This approach is proved to be effective to suppress direct current drift in polymer EO modulators.

  12. High sensitivity electro-optic modulation of slow light in ellipse rods PC-CROW

    Science.gov (United States)

    Li, Changhong; Wan, Yong; Zong, Weihua

    2017-07-01

    A tunable slow light with low group velocity, high buffer performance and high sensitivity is realized in photonic crystal coupled resonator optical waveguide (PC-CROW) with elliptical rod around cavity. By adjusting the long axis and short axis of the elliptical rods, the slow light and buffer performance of PC-CROW are optimized. As ae=0.42a, be=0.20a, the group velocity is below 2.3053×10-4c, simultaneously, the buffer capacity C and delay time Ts reach the optimum value of 9.8214 bit and 354.8 ps. Then the dynamic modulation of the slow light and buffer performance based on this optimized structure has been discussed systematically. Thanks to the electro-optic effect of the polystyrene substrate, the guided mode shifts linearly to short wavelength in sensitivity of 3.0 nm/mV around 1550 nm, as the applied voltage increases. The modulation sensitivities of delay time and buffer capacity are 0.445 ns/mV and 0.051 bit/mV, respectively. These results show a considerable potential for this structure that can be dynamically controlled according to the practical requirements by electro-optic effect in PC-CROW.

  13. Electromechanical and electro-optical functions of plasticized PVC with colossal dielectric constant

    Science.gov (United States)

    Sato, Hiromu; Hirai, Toshihiro

    2013-04-01

    A soft dielectric polymer, plasticized poly(vinyl chloride) (PVC gel), has been known as a characteristic actuator with electrotactic creep deformation. The deformation can be applied for bending and contraction. The mechanism of the deformation has been attributed to the colossal dielectric constant of the gel induced by dc field. The dielectric constant at 1 Hz, jumps from less than10 to thousand times larger value. The huge dielectric constant suggests the gel can have electro-optic function. In this paper, we introduce the gel can bend light direction by applying a dc electric field. The PVC gel can bend light direction depending on the electric field. Detailed feature of the light bending will be introduced and discussed. Bending angle can be controlled by dielectric plasticizer and electric field. The components of the gel, PVC and plasticizer themselves, did not show any effect of electro-optical function like the PVC gel. The same feature can be observed in other polymer, like poly(vinyl alcohol)-dimethyl sulphoxide gel, too.

  14. Experimental and theoretical investigation of electro-optic and all-optical implementations of wavelength converting 2R-regenerators

    DEFF Research Database (Denmark)

    Wolfson, David; Mikkelsen, Benny; Danielsen, Søren Lykke

    1998-01-01

    We investigate and compare the regenerative capability of electro-optic wavelength converters based on electrically controlled external Mach-Zehnder (MZ) modulators and all-optical wavelength converters based on all-optically controlled external MZ modulators. The latter incorporates semiconductor...... optical amplifiers (SOAs) as optically controlled phase shifters. Experiments demonstrate a 5-6 dB noise suppression capability for both the electro-optic and the all-optical implementation of the wavelength-converting regenerators. The performance can be further improved by cascading two converters...

  15. Reprint of: Coulomb field strength measurement by electro-optic spectral decoding system at the CALIFES beam line

    Energy Technology Data Exchange (ETDEWEB)

    Pan, R., E-mail: rui.pan@stfc.ac.uk [Accelerator Science and Technology Centre, Science and Technology Facilities Council, Darebsury Laboratory, Keckwick Lane, Daresbury WA4 4AD (United Kingdom); School of Engineering, Physics and Mathematics, University of Dundee, Nethergate, Dundee DD1 4HN (United Kingdom); Jamison, S.P. [Accelerator Science and Technology Centre, Science and Technology Facilities Council, Darebsury Laboratory, Keckwick Lane, Daresbury WA4 4AD (United Kingdom); Lefevre, T. [CERN, CH-1211 Geneva 23 (Switzerland); Gillespie, W.A. [School of Engineering, Physics and Mathematics, University of Dundee, Nethergate, Dundee DD1 4HN (United Kingdom)

    2016-09-11

    Electro-optic (EO) techniques are increasingly used for longitudinal bunch profile measurements. A bunch profile monitor, based on electro-optic spectral decoding (EOSD), has been developed and demonstrated on the CALIFES beam line at CERN. The EO response is analysed using a frequency domain description, and two methods for extraction of absolute Coulomb field strengths from the electron bunch are demonstrated. Measurements at field strengths up to 1.3 MV/m agree with the expectation based on independent charge measurements.

  16. Study of Electro-Optical Measuring System for Measuring the Swaying of Rocket Launcher and Artillery Systems

    Institute of Scientific and Technical Information of China (English)

    LI Yang; YAN Yu-feng; CAI Li-juan; LIU Zhen-bo

    2008-01-01

    A scheme is proposed, of that the axis of directional barrel is simulated by a laser beam and an electro-optical axial angle encoder is using to measure the swaying of rocket Muncher or artillery. The measuring principle is stated, and an electro-optical measuring system is designed, including automatic force-applying device, angle-measurement device and photodetecting screen. The measurement accuracy of the system is analyzed. The measuring error of system is less then 17.3"(0.08 mil).

  17. Reprint of: Coulomb field strength measurement by electro-optic spectral decoding system at the CALIFES beam line

    Science.gov (United States)

    Pan, R.; Jamison, S. P.; Lefevre, T.; Gillespie, W. A.

    2016-09-01

    Electro-optic (EO) techniques are increasingly used for longitudinal bunch profile measurements. A bunch profile monitor, based on electro-optic spectral decoding (EOSD), has been developed and demonstrated on the CALIFES beam line at CERN. The EO response is analysed using a frequency domain description, and two methods for extraction of absolute Coulomb field strengths from the electron bunch are demonstrated. Measurements at field strengths up to 1.3 MV/m agree with the expectation based on independent charge measurements.

  18. 无人机光电载荷及其应用%UAV Electro-optical Payloads and Application

    Institute of Scientific and Technical Information of China (English)

    王正林

    2013-01-01

      简要介绍了无人机优势及应用范围,对目前世界上主要固定翼无人机及无人直升机的光电载荷进行了研究分析,在此基础上,对新型无人飞行器概念平台进行介绍。最后总结了无人机光电载荷发展趋势,即随着无人机平台技术及光电载荷技术的迅速发展,长航时、良好隐身性、多用途、具备主动光电干扰能力、高智能将是无人机光电载荷的发展趋势。%The advantages and applications of unmanned aerial vehicle (UAV) are briefly introduced. The electro-optical payloads on fixed wing UAV and UAV helicopter are analyzed. Based on this, the new UAV plat⁃form is introduced. The development trends of UAV electro-optical payloads are summarized in the end. With the rapid development of UAV platform technology and electro-optical payload technology, UAV electro-opti⁃cal payloads will have the characteristics of long endurance, good stealthy, multipurpose, active electro-optical jamming ability and high intelligence.

  19. Optimized Optical Rectification and Electro-optic Sampling in ZnTe Crystals with Chirped Femtosecond Laser Pulses

    DEFF Research Database (Denmark)

    Erschens, Dines Nøddegaard; Turchinovich, Dmitry; Jepsen, Peter Uhd

    2011-01-01

    We report on optimization of the intensity of THz signals generated and detected by optical rectification and electro-optic sampling in dispersive, nonlinear media. Addition of a negative prechirp to the femtosecond laser pulses used in the THz generation and detection processes in 1-mm thick ZnT...

  20. Electro-optical properties of a polymer light-emitting diode with an injection-limited hole contact

    NARCIS (Netherlands)

    van Woudenbergh, T; Blom, PWM; Huiberts, JN

    2003-01-01

    The electro-optical characteristics of a polymer light-emitting diode with a strongly reduced hole injection have been investigated. A silver contact on poly-dialkoxy-p-phenylene vinylene decreases the hole injection by five orders of magnitude, resulting in both a highly reduced light output and cu

  1. On the design and construction of drifting-mine test targets for sonar, radar and electro-optical detection experiments

    NARCIS (Netherlands)

    Dol, H.S.

    2014-01-01

    The timely detection of small hazardous objects at the sea surface, such as drifting mines, is challenging for ship-mounted sensor systems, both for underwater sensor systems like sonar and above-water sensor systems like radar and electro-optics (lidar, infrared/visual cameras). This is due to the

  2. Electro-optical effects in porous PET films filled with liquid crystal: new possibilities for fiber optics and THZ applications.

    Science.gov (United States)

    Chopik, A; Pasechnik, S; Semerenko, D; Shmeliova, D; Dubtsov, A; Srivastava, A K; Chigrinov, V

    2014-03-15

    The results of investigation of electro-optical properties of porous polyethylene terephthalate films filled with a nematic liquid crystal (5 CB) are presented. It is established that the optical response of the samples on the applied voltage drastically depends on the frequency range. At low frequencies of applied electrical field (foptical response arises as an impulse of light intensity, which decays for the time essentially shorter than the electric pulse duration. At high frequencies (f>fc) electric field induces an overall change in the light intensity, which is typical for an electro-optical response of a liquid crystal (LC) layer in a conventional "sandwich"-like cell. The dependences of critical frequency fc, threshold voltages, and characteristic times on a pore diameter d were established. The peculiarities of electro-optical effects can be explained in the framework of the approach which connects the variations of light intensity with the corresponding changes of the effective refractive index n(eff) of a composite LC media. The unusual behavior of the electro-optical response at low frequencies is assigned to the orienting action of the specific shear flow typical for electrokinetic phenomena in polar liquids.

  3. Aluminum nitride electro-optic phase shifter for backend integration on silicon.

    Science.gov (United States)

    Zhu, Shiyang; Lo, Guo-Qiang

    2016-06-13

    An AlN electro-optic phase shifter with a parallel plate capacitor structure is fabricated on Si using the back-end complementary metal-oxide-semiconductor technology, which is feasible for multilayer photonics integration. The modulation efficiency (Vπ⋅Lπ product) measured from the fabricated waveguide-ring resonators and Mach-Zehnder Interferometer (MZI) modulators near the 1550-nm wavelength is ∼240 V⋅cm for the transverse electric (TE) mode and ∼320 V⋅cm for the transverse magnetic (TM) mode, from which the Pockels coefficient of the deposited AlN is deduced to be ∼1.0 pm/V for both TE and TM modes. The methods for further modulation efficiency improvement are addressed.

  4. Retardance and flicker modeling and characterization of electro-optic linear retarders by averaged Stokes polarimetry.

    Science.gov (United States)

    Martínez, Francisco J; Márquez, Andrés; Gallego, Sergi; Francés, Jorge; Pascual, Inmaculada; Beléndez, Augusto

    2014-02-15

    A polarimetric method for the measurement of linear retardance in the presence of phase fluctuations is presented. This can be applied to electro-optic devices behaving as variable linear retarders. The method is based on an extended Mueller matrix model for the linear retarder containing the time-averaged effects of the instabilities. As a result, an averaged Stokes polarimetry technique is proposed to characterize both the retardance and its flicker magnitude. Predictive capability of the approach is experimentally demonstrated, validating the model and the calibration technique. The approach is applied to liquid crystal on silicon displays (LCoS) using a commercial Stokes polarimeter. Both the magnitude of the average retardance and the amplitude of its fluctuation are obtained for each gray level value addressed, thus enabling a complete phase characterization of the LCoS.

  5. A compact plasmonic MOS-based 2×2 electro-optic switch

    Science.gov (United States)

    Ye, Chenran; Liu, Ke; Soref, Richard A.; Sorger, Volker J.

    2015-01-01

    We report on a three-waveguide electro-optic switch for compact photonic integrated circuits and data routing applications. The device features a plasmonic metal-oxide-semiconductor (MOS) mode for enhanced light-matter-interactions. The switching mechanism originates from a capacitor-like design where the refractive index of the active medium, indium-tin-oxide, is altered via shifting the plasma frequency due to carrier accumulation inside the waveguide-based MOS structure. This light manipulation mechanism controls the transmission direction of transverse magnetic polarized light into either a CROSS or BAR waveguide port. The extinction ratio of 18 (7) dB for the CROSS (BAR) state, respectively, is achieved via a gating voltage bias. The ultrafast broadband fJ/bit device allows for seamless integration with silicon-on-insulator platforms for low-cost manufacturing.

  6. High-speed switching of biphoton delays through electro-optic pump frequency modulation

    Directory of Open Access Journals (Sweden)

    Ogaga D. Odele

    2017-01-01

    Full Text Available The realization of high-speed tunable delay control has received significant attention in the scene of classical photonics. In quantum optics, however, such rapid delay control systems for entangled photons have remained undeveloped. Here for the first time, we demonstrate rapid (2.5 MHz modulation of signal-idler arrival times through electro-optic pump frequency modulation. Our technique applies the quantum phenomenon of nonlocal dispersion cancellation along with pump frequency tuning to control the relative delay between photon pairs. Chirped fiber Bragg gratings are employed to provide large amounts of dispersion which result in biphoton delays exceeding 30 ns. This rapid delay modulation scheme could be useful for on-demand single-photon distribution in addition to quantum versions of pulse position modulation.

  7. Modeling of multilayer electrode performance in transverse electro-optic modulators

    Directory of Open Access Journals (Sweden)

    Minmin Zhu

    2011-12-01

    Full Text Available For some electro-optic (EO modulators, lowering the driving voltage is necessary to reduce the power consumption of the modulators. There are four significant factors influencing the driving voltage of the EO modulators: geometrical parameters of wafer and electrodes, surface and embedded electrodes, material properties of wafer, and structure of modulators. Using the superposition method and surface charge technique, the electric fields, halfwave voltages, switching times and optical transmissions of EO modulators with two-layer, three-layer, and four-layer electrodes are calculated, respectively. It is found that the halfwave voltage decreases while the switching time increase slightly as the number of layers increases. Such study demonstrates that using multilayer electrodes is an effective technique of lowering the halfwave voltage, which may have implication of EO modulator design.

  8. A 130 GHz Electro-Optic Ring Modulator with Double-Layer Graphene

    Directory of Open Access Journals (Sweden)

    Lei Wu

    2017-02-01

    Full Text Available The optical absorption coefficient of graphene will change after injecting carriers. Based on this principle, a high-speed double-layer graphene electro-optic modulator with a ring resonator structure was designed in this paper. From the numerical simulations, we designed a modulator. Its optical bandwidth is larger than 130 GHz, the switching energy is 0.358 fJ per bit, and the driven voltage is less than 1.2 V. At the same time, the footprint of the proposed modulator is less than 10 microns squared, which makes the process compatible with the Complementary Metal Oxide Semiconductors (CMOS process. This will provide the possibility for the on-chip integration of the photoelectric device.

  9. High Cost Performance Organic-Inorganic Hybrid Material for Electro-optic Devices

    Institute of Scientific and Technical Information of China (English)

    SUN Jie; ZHU Gui-Hua; SUN Xiao-Qiang; LI Tong; GAO Wei-Nan; ZHANG Da-Ming; HOU A-lin

    2009-01-01

    We report a low-cost electro-optic (EO) sol-gel material with large EO coefficient and excellent poling stability for EO devices. Disperse red 1 (DR1) chromophore is doped in the three-dimensional silicon dioxide/titanium dioxide network possessing a high γ33 (88pm/V at 1300 nm wavelength and 71 pm/V at 1550nm wavelength). Favourable poled stability (less than 5% relaxed after 2500 hours at 80 ℃) and low absorption are demonstrated. Strip-loaded waveguide Mach-Zehnder (M-Z) modulators are implemented based on this synthesized EO material, showing 7 V half-wave voltage and less than 9dB insertion loss at 1550nm wavelength.

  10. A Single Shot, Sub-picosecond Beam Bunch Characterization with Electro-optic Techniques

    CERN Document Server

    Semertzidis, Y K; Castillo, V; Larsen, R; Lazarus, D M; Nikas, D; Ozben, C; Srinivasan-Rao, T; Stillman, A; Tsang, Thomas; Kowalski, L A

    2001-01-01

    In the past decade, the bunch lengths of electrons in accelerators have decreased dramatically to the range of a few picoseconds \\cite{Uesaka94,Trotz97}. Measurement of the length as well as the longitudinal profile of these short bunches have been a topic of research in a number of institutions \\cite{Uesaka97,Liu97,Hutchins00}. One of the techniques uses the electric field induced by the passage of electrons in the vicinity of a birefringent crystal to change its optical characteristics. Well-established electro-optic techniques can then be used to measure the temporal characteristics of the electron bunch. In this paper we present a novel, non-invasive, single-shot approach to improve the resolution to tens of femtoseconds so that sub-millimeter bunch length can be measured.

  11. Reconfigurable electro-optical directed-logic circuit using carrier-depletion micro-ring resonators.

    Science.gov (United States)

    Qiu, Ciyuan; Gao, Weilu; Soref, Richard; Robinson, Jacob T; Xu, Qianfan

    2014-12-15

    Here we demonstrate a reconfigurable electro-optical directed-logic circuit based on a regular array of integrated optical switches. Each 1×1 optical switch consists of a micro-ring resonator with an embedded lateral p-n junction and a micro-heater. We achieve high-speed on-off switching by applying electrical logic signals to the p-n junction. We can configure the operation mode of each switch by thermal tuning the resonance wavelength. The result is an integrated optical circuit that can be reconfigured to perform any combinational logic operation. As a proof-of-principle, we fabricated a multi-spectral directed-logic circuit based on a fourfold array of switches and showed that this circuit can be reconfigured to perform arbitrary two-input logic functions with speeds up to 3  GB/s.

  12. Study on electro-optic properties of two-dimensional PLZT photonic crystal band structure

    Institute of Scientific and Technical Information of China (English)

    TONG Kai; WU Xiao-gang; WANG Mei-ting

    2011-01-01

    The band characteristics of two-dimensional (2D) lead lanthanum zirconate titanate (PLZT) photonic cystals are analyzed by finite element method. The electro-optic effect of PLZT can cause the refractive index change when it is imposed by the applied electric field, and the band structure of 2D photonic crystals based on PLZT varies accordingly. The effect of the applied electric field on the structural characteristics of the first and second band gaps in 2D PLZT photonic crystals is analyzed in detail. And the results show that for each band gap, the variations of start wavelength, cut-off wavelength and bandwidth are proportional to quadratic of the electric field.

  13. Correlations of electro-optical and nanostructural properties of CdTe thin films

    Science.gov (United States)

    Levi, D. H.; Moutinho, H. R.; Hasoon, F. S.; Ahrenkiel, R. K.; Kazmerski, L. L.; Al-Jassim, M. M.

    1996-01-01

    This paper presents correlations of macroscopic optical properties with the nanoscale physical and electronic structure of CdTe/CdS thin films used for photovoltaic cell fabrication. We have studied the evolution of these properties under systematic variation of post-growth treatment conditions for several standard deposition techniques. The electro-optical properties and nanostructure depend strongly on deposition conditions and post-growth treatments. Our results indicate that the standard CdCl2—heat treatment enhances grain size and passivates defects. We have also found strong evidence for sulfur diffusion across the CdTe—CdS interface. This interdiffusion produces a thin layer at the junction with a bandgap lower than the rest of the absorber layer. This effect could have important implications for photoexcited carrier collection in photovoltaic applications.

  14. Correlations of electro-optical and nanostructural properties of CdTe thin films

    Energy Technology Data Exchange (ETDEWEB)

    Levi, D.H.; Moutinho, H.R.; Hasoon, F.S.; Ahrenkiel, R.K.; Kazmerski, L.L.; Al-Jassim, M.M. [National Renewable Energy Laboratory, 1617 Cole Blvd., Golden, Colorado 80401 (United States)

    1996-01-01

    This paper presents correlations of macroscopic optical properties with the nanoscale physical and electronic structure of CdTe/CdS thin films used for photovoltaic cell fabrication. We have studied the evolution of these properties under systematic variation of post-growth treatment conditions for several standard deposition techniques. The electro-optical properties and nanostructure depend strongly on deposition conditions and post-growth treatments. Our results indicate that the standard CdCl{sub 2}{emdash}heat treatment enhances grain size and passivates defects. We have also found strong evidence for sulfur diffusion across the CdTe{emdash}CdS interface. This interdiffusion produces a thin layer at the junction with a bandgap lower than the rest of the absorber layer. This effect could have important implications for photoexcited carrier collection in photovoltaic applications. {copyright} {ital 1996 American Institute of Physics.}

  15. Stabilisation of a fibre frequency synthesiser using acousto-optical and electro-optical modulators

    Science.gov (United States)

    Koliada, N. A.; Nyushkov, B. N.; Pivtsov, V. S.; Dychkov, A. S.; Farnosov, S. A.; Denisov, V. I.; Bagayev, S. N.

    2016-12-01

    A fibre-optic frequency synthesiser is developed that is stabilised to the optical frequency standard based on molecular iodine ({\\text{Nd : YAG/I}}2). The possibility of transferring stability of the optical frequency standard to other optical frequencies in the IR range 1 - 2 \\unicode{956}{\\text{m}} and to the RF range by using synthesiser phase-locked loops (PLLs) with acousto-optical and electro-optical modulators is experimentally demonstrated. The additive instability introduced into the optical frequency comb of the synthesiser (which arises due to PLL residual random errors) is several orders less than the intrinsic instability of the reference optical frequency standard employed (i.e., is noticeably less than 1 × 10-13 for 1 {\\text{s}} and 5 × 10-15 for 1000 {\\text{s}}).

  16. A compact plasmonic MOS-based 2x2 electro-optic switch

    CERN Document Server

    Ye, Chenran; Soref, Richard A; Sorger, Volker J

    2015-01-01

    We report on a three-waveguide electro-optic switch for compact photonic integrated circuits and data routing applications. The device features a plasmonic metal-oxide-semiconductor (MOS) mode for enhanced light-matter-interactions. The switching mechanism originates from a capacitor-like design where the refractive index of the active medium, Indium-Tin-Oxide, is altered via shifting the plasma frequency due to carrier accumulation inside the waveguide-based MOS structure. This light manipulation mechanism controls the transmission direction of transverse magnetic polarized light into either a CROSS or BAR waveguide port. The extinction ratio of 18 dB (7) dB for the CROSS (BAR) state, respectively, is achieved via a gating voltage bias. The ultrafast broadband fJ/bit device allows for seamless integration with Siliconon- Insulator platforms to for low-cost manufacturing.

  17. Design of a multi-point microwave interferometer using the electro-optic effect

    Science.gov (United States)

    Specht, Paul E.; Cooper, Marcia A.; Jilek, Brook A.

    2017-01-01

    A multi-point microwave interferometer (MPMI) concept is presented for non-invasively monitoring the internal transit of a shock, detonation, or reaction front in energetic media. The concept utilizes an electro-optic (EO) crystal to impart a time-varying phase lag onto a laser with a microwave signal. Polarization optics convert this phase lag into an amplitude modulation. A heterodyne interferometer compares the modulated laser beam to a constant reference. This enables the detection of changes in the modulating microwave frequency generated by the motion of the measurement surface. The design is scalable and makes use of the established construction and analysis methods employed in photonic Doppler velocimetry (PDV). The technical challenges associated with the concept are the frequency stability of the lasers, the amount of light return after EO modulation, and the frequency uncertainty of fast Fourier transform (FFT) methods.

  18. An investigation on a novel PDLC film’s fabrication and its electro-optical properties

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A polymer dispersed liquid crystal (PDLC) film that has good electro-optical properties is produced by the method of polymerized-induced phase separation. Based on the application foreground, its capability parameters, such as contrast ratio, work voltage, and visual angle, are characterized for the first time by a white light but not a fixed wavelength light. The results show the PDLC film has a low work-voltage of 20 V, more than 150° visual angle, high stability, and long lifetime. The differences between plastic and glass ITO-coated substrates of PDLC films are also studied in this paper. The plastic substrate has better property and will have a wider perspective especially in the portable, tender and folded display devices. Due to adjustable properties of film by electric field, PDLC has the potential application for display device, sensor, switch, grating, and new generation analytical apparatus.

  19. An innovative procedure for calibration of strapdown electro-optical sensors onboard unmanned air vehicles.

    Science.gov (United States)

    Fasano, Giancarmine; Accardo, Domenico; Moccia, Antonio; Rispoli, Attilio

    2010-01-01

    This paper presents an innovative method for estimating the attitude of airborne electro-optical cameras with respect to the onboard autonomous navigation unit. The procedure is based on the use of attitude measurements under static conditions taken by an inertial unit and carrier-phase differential Global Positioning System to obtain accurate camera position estimates in the aircraft body reference frame, while image analysis allows line-of-sight unit vectors in the camera based reference frame to be computed. The method has been applied to the alignment of the visible and infrared cameras installed onboard the experimental aircraft of the Italian Aerospace Research Center and adopted for in-flight obstacle detection and collision avoidance. Results show an angular uncertainty on the order of 0.1° (rms).

  20. Spectral Shearing of Quantum Light Pulses by Electro-Optic Phase Modulation.

    Science.gov (United States)

    Wright, Laura J; Karpiński, Michał; Söller, Christoph; Smith, Brian J

    2017-01-13

    Frequency conversion of nonclassical light enables robust encoding of quantum information based upon spectral multiplexing that is particularly well-suited to integrated-optics platforms. Here we present an intrinsically deterministic linear-optics approach to spectral shearing of quantum light pulses and show it preserves the wave-packet coherence and quantum nature of light. The technique is based upon an electro-optic Doppler shift to implement frequency shear of heralded single-photon wave packets by ±200  GHz, which can be scaled to an arbitrary shift. These results demonstrate a reconfigurable method to controlling the spectral-temporal mode structure of quantum light that could achieve unitary operation.

  1. Simultaneous measurement of electro-optical and converse-piezoelectric coefficients of PMN-PT ceramics.

    Science.gov (United States)

    Xiao, Pingping; Wang, Xianping; Sun, Jingjing; Huang, Meizhen; Chen, Xianfeng; Cao, Zhuangqi

    2012-06-18

    A new scheme is proposed to measure the electro-optical (EO) and converse-piezoelectric (CPE) coefficients of the PMN-PT ceramics simultaneously, in which the PMN-PT ceramics acts as the guiding layer of a symmetrical metal-cladding waveguide. As the applied electric field exerts on the waveguide, the effective refractive index (RI) (or synchronous angle) can be effectively tuned from a selected mode to another adjacent mode owing to the high sensitivity and the small spacing of the ultra-high order modes. Subsequently, a correlation between EO and CPE coefficients is established. With this correlation and the measurement of the effective RI change to the applied voltage, the quadratic EO and CPE coefficients of PMN-PT ceramics are obtained simultaneously. The obtained results are further checked by fitting the variations of effective RI to a quadratic function. Our measurement method can be extended to a wide range of other materials.

  2. Electro-optic modulation methods in range-gated active imaging.

    Science.gov (United States)

    Chen, Zhen; Liu, Bo; Liu, Enhai; Peng, Zhangxian

    2016-01-20

    A time-resolved imaging method based on electro-optic modulation is proposed in this paper. To implement range resolution, two kinds of polarization-modulated methods are designed, and high spatial and range resolution can be achieved by the active imaging system. In the system, with polarization beam splitting the incident light is split into two parts, one of which is modulated with cos(2) function and the other is modulated with sin(2) function. Afterward, a depth map can be obtained from two simultaneously received images by dual electron multiplying charge-coupled devices. Furthermore, an intensity image can also be obtained from the two images. Comparisons of the two polarization-modulated methods indicate that range accuracy will be promoted when the polarized light is modulated before beam splitting.

  3. Lidar Electro-Optic Beam Switch with a Liquid Crystal Variable Retarder

    Science.gov (United States)

    Baer, James

    2012-01-01

    A document discusses a liquid crystal variable retarder, an electro-optic element that changes the polarization of an optical beam in response to a low-voltage electronic signal. This device can be fabricated so that the element creates, among other states, a half-wave of retardance that can be reduced to a very small retardance. When aligned to a polarized source, this can act to rotate the polarization by 90 in one state, but generate no rotation in the other state. If the beam is then incident on a polarization beam splitter, it will efficiently switch from one path to the other when the voltage is applied. The laser beam switching system has no moving parts, improving reliability over mechanical switching. It is low cost, tolerant of high laser power density, and needs only simple drive electronics, minimizing the required system resources.

  4. Strictly non-blocking 4×4 silicon electro-optic switch matrix

    Science.gov (United States)

    Zhou, Pei-Ji; Xing, Jie-Jiang; Li, Xian-Yao; Li, Zhi-Yong; Yu, Jin-Zhong; Yu, Yu-De

    2015-12-01

    The first path-independent insertion-loss (PILOSS) strictly non-blocking 4×4 silicon electro-optic switch matrix is reported. The footprint of this switch matrix is only 4.6 mm×1.0 mm. Using single-arm modulation, the crosstalk measured in this test is -13 dB˜ -27 dB. And a maximum crosstalk deterioration of 6dB caused by two-path interference is also found. Project supported by the National Basic Research Program of China (Grant No. 2011CB301701), the National High Technology Research and Development Program of China (Grant Nos. 2013AA014402, 2012AA012202, and 2015AA016904), and the National Natural Science Foundation of China (Grant Nos. 61275065 and 61107048).

  5. Defect enhanced optic and electro-optic properties of lead zirconate titanate thin films

    Directory of Open Access Journals (Sweden)

    M. M. Zhu

    2011-12-01

    Full Text Available Pb(Zr1-xTixO3 (PZT thin films near phase morphotropic phase boundary were deposited on (Pb0.86La0.14TiO3-coated glass by radio frequency sputtering. A retrieved analysis shows that the lattice parameters of the as-grown PZT thin films were similar to that of monoclinic PZT structure. Moreover, the PZT thin films possessed refractive index as high as 2.504 in TE model and 2.431 in TM model. The as-grown PZT thin film had one strong absorption peak at 632.6 nm, which attributed to lead deficiency by quantitative XPS analysis. From the attractive properties achieved, electro-optic and photovoltaic characteristic of the films were carried out.

  6. Self-referencing a continuous-wave laser with electro-optic modulation

    CERN Document Server

    Beha, Katja; Del'Haye, Pascal; Coillet, Aurélien; Diddams, Scott A; Papp, Scott B

    2015-01-01

    We phase-coherently measure the frequency of continuous-wave (CW) laser light by use of optical-phase modulation and f-2f nonlinear interferometry. Periodic electro-optic modulation (EOM) transforms the CW laser into a continuous train of picosecond optical pulses. Subsequent nonlinear-fiber broadening of this EOM frequency comb produces a supercontinuum with 160 THz of bandwidth. A critical intermediate step is optical filtering of the EOM comb to reduce electronic-noise-induced decoherence of the supercontinuum. Applying f-2f self-referencing with the supercontinuum yields the carrier-envelope offset frequency of the EOM comb, which is precisely the difference of the CW laser frequency and an exact integer multiple of the EOM pulse repetition rate. Here we demonstrate absolute optical frequency metrology and synthesis applications of the self-referenced CW laser with <5E-14 fractional accuracy and stability.

  7. Design of slotted high quality factor photonic-crystal nanocavities embedded in electro-optic polymers

    Science.gov (United States)

    Nakadai, Masahiro; Konoike, Ryotaro; Tanaka, Yoshinori; Asano, Takashi; Noda, Susumu

    2017-09-01

    We improve design quality factors of slotted photonic crystal nanocavities embedded in electro-optic polymers (EOPs), which enables control of resonant wavelengths without the use of light-absorbing free carriers. We form nanocavities by modifying single- and double-slotted line-defect waveguides with lattice-constant modulations analytically determined based on dispersions of the waveguides. A double-slotted nanocavity achieves a fourfold increase in Q factor (36 million) compared to a single-slotted nanocavity with similar modulation of lattice constants. Both structures can realize large concentration of light in the EOP region (50%), and resonant wavelength modulations of ∼0.01% are expected with applied voltage of 2 V.

  8. Loop-locked coherent population trapping magnetometer based on a fiber electro-optic modulator.

    Science.gov (United States)

    Hu, Yong; Feng, Y Y; Xu, Chi; Xue, H B; Sun, Li

    2014-04-01

    We have set up a coherent population trapping (CPT)-based magnetometer prototype with the D1 line of ⁸⁷Rb atoms. The dichromatic light field is derived from a fiber electro-optic modulator (FEOM) connected to an external cavity laser diode. A CPT resonance signal with a 516 Hz linewidth is observed. By feeding back the derivative of the resonance curve to the FEOM with a proportional integral controller, of which the voltage output is directly converted to the measured magnetic field intensity, the resonance peak is locked to the environmental magnetic field. The measurement data we have achieved are well matched with the data measured by a commercial fluxgate magnetometer within 2 nT, and the sensitivity is better than 8 pT/√Hz in a parallel B field.

  9. Capacitively-Induced Free-Carrier Effects in Nanoscale Silicon Waveguides for Electro-Optic Modulation

    CERN Document Server

    Sharma, Rajat; Lin, Hung-Hsi; Isichenko, Andrei; Vallini, Felipe; Fainman, Yeshaiahu

    2015-01-01

    We fabricate silicon waveguides in silicon-on-insulator (SOI) wafers clad with either silicon dioxide, silicon nitride, or aluminum oxide, and by measuring the electro-optic behavior of ring resonators, we characterize the cladding-dependent and capacitively-induced free-carrier effects in each of these waveguides. By comparing our measured data with simulation results, we confirm that the observed voltage dependencies of the transmission spectra are due to changes in the concentrations of holes and electrons within the semiconductor waveguide, and we show for the first time how strongly these effects depend on the cladding material which comes into contact with the silicon waveguide. Additionally, the waveguide loss is found to have a particularly high sensitivity to the applied voltage, and may therefore find use in a wide range of applications which require low- or high-loss propagation. Collectively, these phenomena may be incorporated into more complex waveguide designs in the future to create high-effic...

  10. Synthesis, characterizations and electro-optical properties of nonlinear optical polyimide/silica hybrid

    Directory of Open Access Journals (Sweden)

    2007-03-01

    Full Text Available Transparent Nonlinear Optical (NLO inorganic/organic (polyimide/silica hybrid composites with covalent links between the inorganic and the organic networks were prepared by the sol-gel method. The silica content in the hybrid films was varied from 0 to 22.5/wt%. The prepared PI hybrids were characterized by IR, UV-Vis, Thermogravimetric analysis (TGA, X-ray diffraction (XRD, Scanning Electron Microscopy (SEM and Transmission Electron Microscopy (TEM. They exhibited fair good optical transparency. The SiO2 phase was well dispersed in the polymer matrix. DSC and TGA results showed that these hybrid materials had excellent thermal stability. The polymer solutions could be spin coated on the indium-tin-oxide (ITO glass to form optical quality thin films. The electro-optic coefficients (γ33 at the wavelength of 832 nm for polymer thin films poled were in the range of 19-27 pm/V.

  11. An Innovative Procedure for Calibration of Strapdown Electro-Optical Sensors Onboard Unmanned Air Vehicles

    Directory of Open Access Journals (Sweden)

    Attilio Rispoli

    2010-01-01

    Full Text Available This paper presents an innovative method for estimating the attitude of airborne electro-optical cameras with respect to the onboard autonomous navigation unit. The procedure is based on the use of attitude measurements under static conditions taken by an inertial unit and carrier-phase differential Global Positioning System to obtain accurate camera position estimates in the aircraft body reference frame, while image analysis allows line-of-sight unit vectors in the camera based reference frame to be computed. The method has been applied to the alignment of the visible and infrared cameras installed onboard the experimental aircraft of the Italian Aerospace Research Center and adopted for in-flight obstacle detection and collision avoidance. Results show an angular uncertainty on the order of 0.1° (rms.

  12. Bandwidth manipulation of quantum light by an electro-optic time lens

    CERN Document Server

    Karpinski, Michal; Wright, Laura J; Smith, Brian J

    2016-01-01

    The ability to manipulate the spectral-temporal waveform of optical pulses has enabled a wide range of applications from ultrafast spectroscopy to high-speed communications. Extending these concepts to quantum light has the potential to enable breakthroughs in optical quantum science and technology. However, filtering and amplifying often employed in classical pulse shaping techniques are incompatible with non-classical light. Controlling the pulsed mode structure of quantum light requires efficient means to achieve deterministic, unitary manipulation that preserves fragile quantum coherences. Here we demonstrate an electro-optic method for modifying the spectrum of non-classical light by employing a time lens. In particular we show highly-efficient wavelength-preserving six-fold compression of single-photon spectral intensity bandwidth, enabling over a two-fold increase of single-photon flux into a spectrally narrowband absorber. These results pave the way towards spectral-temporal photonic quantum informati...

  13. Measurement of Wave Electric Fields in Plasmas by Electro-Optic Probe

    CERN Document Server

    Nishiura, M; Mushiake, T; Kawazura, Y; Osawa, R; Fujinami, K; Yano, Y; Saitoh, H; Yamasaki, M; Kashyap, A; Takahashi, N; Nakatsuka, M; Fukuyama, A

    2016-01-01

    Electric field measurement in plasmas permits quantitative comparison between the experiment and the simulation in this study. An electro-optic (EO) sensor based on Pockels effect is demonstrated to measure wave electric fields in the laboratory magnetosphere of the RT-1 device with high frequency heating sources. This system gives the merits that electric field measurements can detect electrostatic waves separated clearly from wave magnetic fields, and that the sensor head is separated electrically from strong stray fields in circumference. The electromagnetic waves are excited at the double loop antenna for ion heating in electron cyclotron heated plasmas. In the air, the measured wave electric fields are in good absolute agreement with those predicted by the TASK/WF2 code. In inhomogeneous plasmas, the wave electric fields in the peripheral region are enhanced compared with the simulated electric fields. The potential oscillation of the antenna is one of the possible reason to explain the experimental resu...

  14. Suppression of Classical and Quantum Radiation Pressure Noise via Electro-Optic Feedback

    CERN Document Server

    Buchler, B C; Shaddock, D A; Ralph, T C; McClelland, D E; Buchler, Ben C.; Gray, Malcolm B.; Shaddock, Daniel A.; Ralph, Timothy C.; Clelland, David E. Mc

    1998-01-01

    We present theoretical results that demonstrate a new technique to be used to improve the sensitivity of thermal noise measurements: intra-cavity intensity stabilisation. It is demonstrated that electro-optic feedback can be used to reduce intra-cavity intensity fluctuations, and the consequent radiation pressure fluctuations, by a factor of two below the quantum noise limit. We show that this is achievable in the presence of large classical intensity fluctuations on the incident laser beam. The benefits of this scheme are a consequence of the sub-Poissonian intensity statistics of the field inside a feedback loop, and the quantum non-demolition nature of radiation pressure noise as a readout system for the intra-cavity intensity fluctuations.

  15. Quantification of helicopter rotor downwash effects on electro-optical defensive aids suites

    Science.gov (United States)

    Seiffer, Dirk P.; Eisele, Christian; Henriksson, Markus; Sjöqvist, Lars; Möller, Sebastian; Togna, Fabio; Velluet, Marie-Thérèse

    2015-10-01

    The performance of electro-optical platform protection systems can be degraded significantly by the propagation environment around the platform. This includes aero-optical effects and zones of severe turbulence generated by engine exhausts. For helicopters rotor tip vortices and engine exhaust gases that are pressed down by the rotor airflow form the so called downwash phenomena. The downwash is a source for perturbations. A wide range of spatial and temporal fluctuations in the refractive index of air can occur. The perturbations from the turbulent flow cause detrimental effects on energy delivery, angle of arrival fluctuations, jam-code transmission, tracking accuracy and imaging performance in general. Therefore the effects may especially have a severe impact on the performance of laser-based protection systems like directed infrared countermeasures (DIRCM). The chain from passive missile detection and warning to obtaining an optical break-lock by the use of an active laser system will be influenced. To anticipate the installed performance of an electro-optical defensive aids suite (DAS) for helicopter platforms it is necessary to develop models for the prediction of the perturbations. Modelled results have to be validated against experimental findings. However, the data available in open literature on the effects of rotor downwash from helicopters on optical propagation is very limited. To collect necessary data and to obtain a first impression about the magnitude of occurring effects the European defence agency group (EDA) on "airborne platform effects on lasers and warning sensors (ALWS)" decided to design and perform a field trial on the premises of the Italian Air Force Flight Test Center in Pratica di Mare, Italy. ALWS is a technical arrangement under the Europa MoU among France, Germany, Italy, Sweden and the United Kingdom.

  16. Ultra-light weight undamped tuned dynamic absorber for cryogenically cooled infrared electro-optic payload

    Science.gov (United States)

    Veprik, Alexander; Babitsky, Vladimir

    2017-04-01

    Attenuation of tonal cryocooler induced vibration in infrared electro-optical payloads may be achieved by using of Tuned Dynamic Absorber (TDA) which is, generally speaking, a passive, weakly damped mass-spring system the resonant frequency of which is precisely matched with the driving frequency. Added TDA results in a favorable modification of the frequency response functions of combined structure. In particular, a favorable antiresonant notch appears at the frequency of tonal excitation along with the adjacent secondary resonance, the width and depth of which along with its closeness to the secondary resonance are strongly dependent on the mass and damping ratios. Using heavier TDA favorably results in wider and deeper antiresonant notch along with increased gap between antiresonant and resonant frequencies. Lowering damping in TDA favorably results in deepening the antiresonant notch. The weight of TDA is usually subjected to tight design constrains. Use of lightweight TDA not only diminishes the attainable performance but also complicates the procedure of frequency matching. Along these lines, even minor frequency deviations may negate the TDA performance and even result in TDA failure in case of resonant build up. The authors are presenting theoretical and practical aspects of designing and constructing ultra-light weight TDA in application to vibration attenuation of electro-optical infrared payload relying on Split Stirling linear cryocooler, the driving frequency of which is fixed and may be accurately tuned and maintained using a digital controller over the entire range of working conditions and lifetime; the lack of mass ratio is compensated by minimizing the damping ratio. In one particular case, in excess of 100-fold vibration attenuation has been achieved by adding as little as 5% to the payload weight.

  17. Electro-optical circuit board with single-mode glass waveguide optical interconnects

    Science.gov (United States)

    Brusberg, Lars; Neitz, Marcel; Pernthaler, Dominik; Weber, Daniel; Sirbu, Bogdan; Herbst, Christian; Frey, Christopher; Queisser, Marco; Wöhrmann, Markus; Manessis, Dionysios; Schild, Beatrice; Oppermann, Hermann; Eichhammer, Yann; Schröder, Henning; Hâkansson, Andreas; Tekin, Tolga

    2016-03-01

    A glass optical waveguide process has been developed for fabrication of electro-optical circuit boards (EOCB). Very thin glass panels with planar integrated single-mode waveguides can be embedded as a core layer in printed circuit boards for high-speed board-level chip-to-chip and board-to-board optical interconnects over an optical backplane. Such singlemode EOCBs will be needed in upcoming high performance computers and data storage network environments in case single-mode operating silicon photonic ICs generate high-bandwidth signals [1]. The paper will describe some project results of the ongoing PhoxTroT project, in which a development of glass based single-mode on-board and board-to-board interconnection platform is successfully in progress. The optical design comprises a 500 μm thin glass panel (Schott D263Teco) with purely optical layers for single-mode glass waveguides. The board size is accommodated to the mask size limitations of the fabrication (200 mm wafer level process, being later transferred also to larger panel size). Our concept consists of directly assembling of silicon photonic ICs on cut-out areas in glass-based optical waveguide panels. A part of the electrical wiring is patterned by thin film technology directly on the glass wafer surface. A coupling element will be assembled on bottom side of the glass-based waveguide panel for 3D coupling between board-level glass waveguides and chip-level silicon waveguides. The laminate has a defined window for direct glass access for assembling of the photonic integrated circuit chip and optical coupling element. The paper describes the design, fabrication and characterization of glass-based electro-optical circuit board with format of (228 x 305) mm2.

  18. Nuclear reactor pulse tracing using a CdZnTe electro-optic radiation detector

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Kyle A., E-mail: nuclearengg@gmail.com [S.M.A.R.T. Laboratory, Mechanical and Nuclear Engineering, Kansas State University, Manhattan KS 66506 (United States); Geuther, Jeffrey A. [TRIGA Mark II Nuclear Reactor, Mechanical and Nuclear Engineering, Kansas State University, Manhattan KS 66506 (United States); Neihart, James L.; Riedel, Todd A. [S.M.A.R.T. Laboratory, Mechanical and Nuclear Engineering, Kansas State University, Manhattan KS 66506 (United States); Rojeski, Ronald A. [Nanometrics, Inc., 1550 Buckeye Drive, Milpitas CA 95035 (United States); Ugorowski, Philip B.; McGregor, Douglas S. [S.M.A.R.T. Laboratory, Mechanical and Nuclear Engineering, Kansas State University, Manhattan KS 66506 (United States)

    2012-07-11

    CdZnTe has previously been shown to operate as an electro-optic radiation detector by utilizing the Pockels effect to measure steady-state nuclear reactor power levels. In the present work, the detector response to reactor power excursion experiments was investigated. Peak power levels during an excursion were predicted to be between 965 MW and 1009 MW using the Fuchs-Nordheim and Fuchs-Hansen models and confirmed with experimental data from the Kansas State University TRIGA Mark II nuclear reactor. The experimental arrangement of the Pockels cell detector includes collimated laser light passing through a transparent birefringent crystal, located between crossed polarizers, and focused upon a photodiode. The birefringent crystal, CdZnTe in this case, is placed in a neutron beam emanating from a nuclear reactor beam port. After obtaining the voltage-dependent Pockels characteristic response curve with a photodiode, neutron measurements were conducted from reactor pulses with the Pockels cell set at the 1/4 and 3/4 wave bias voltages. The detector responses to nuclear reactor pulses were recorded in real-time using data logging electronics, each showing a sharp increase in photodiode current for the 1/4 wave bias, and a sharp decrease in photodiode current for the 3/4 wave bias. The polarizers were readjusted to equal angles in which the maximum light transmission occurred at 0 V bias, thereby, inverting the detector response to reactor pulses. A high sample rate oscilloscope was also used to more accurately measure the FWHM of the pulse from the electro-optic detector, 64 ms, and is compared to the experimentally obtained FWHM of 16.0 ms obtained with the {sup 10}B-lined counter.

  19. An airborne thematic thermal infrared and electro-optical imaging system

    Science.gov (United States)

    Sun, Xiuhong; Shu, Peter

    2011-08-01

    This paper describes an advanced Airborne Thematic Thermal InfraRed and Electro-Optical Imaging System (ATTIREOIS) and its potential applications. ATTIREOIS sensor payload consists of two sets of advanced Focal Plane Arrays (FPAs) - a broadband Thermal InfraRed Sensor (TIRS) and a four (4) band Multispectral Electro-Optical Sensor (MEOS) to approximate Landsat ETM+ bands 1,2,3,4, and 6, and LDCM bands 2,3,4,5, and 10+11. The airborne TIRS is 3-axis stabilized payload capable of providing 3D photogrammetric images with a 1,850 pixel swathwidth via pushbroom operation. MEOS has a total of 116 million simultaneous sensor counts capable of providing 3 cm spatial resolution multispectral orthophotos for continuous airborne mapping. ATTIREOIS is a complete standalone and easy-to-use portable imaging instrument for light aerial vehicle deployment. Its miniaturized backend data system operates all ATTIREOIS imaging sensor components, an INS/GPS, and an e-Gimbal™ Control Electronic Unit (ECU) with a data throughput of 300 Megabytes/sec. The backend provides advanced onboard processing, performing autonomous raw sensor imagery development, TIRS image track-recovery reconstruction, LWIR/VNIR multi-band co-registration, and photogrammetric image processing. With geometric optics and boresight calibrations, the ATTIREOIS data products are directly georeferenced with an accuracy of approximately one meter. A prototype ATTIREOIS has been configured. Its sample LWIR/EO image data will be presented. Potential applications of ATTIREOIS include: 1) Providing timely and cost-effective, precisely and directly georeferenced surface emissive and solar reflective LWIR/VNIR multispectral images via a private Google Earth Globe to enhance NASA's Earth science research capabilities; and 2) Underflight satellites to support satellite measurement calibration and validation observations.

  20. TOD: a new method to characterize electro-optical system performance

    Science.gov (United States)

    Bijl, Piet; Valeton, J. M.

    1998-08-01

    The current standard to characterize Electro-Optical system performance is the MRTD (Minimum Resolvable Temperature Difference) for thermal imagers and the MRC (Minimum Resolvable Contrast) for visual devices. This standard has at least three serious disadvantages: (1) the standard 4-bar test pattern is theoretically and practically unsuitable for 1D or 2D spatially sampled systems such as pixel-array camera's, (2) spatial phase is not taken into account, and (3) the results depend on the observer's subjective decision criterion. We propose an adequate and easily applicable alternative: TOD (Triangle Orientation Discrimination threshold). The TOD is based on an improved test pattern, a better defined observer task, and a solid psychophysical measurement procedure. The new method has theoretical and practical advantages: it is suitable for pixel-array camera's, scanning systems and other (Electro-) Optical imaging systems in both the thermal and vision domain, it has a close relationship to real target acquisition, and the observer task is easy. The results are free from observer bias and allow statistical significance tests. The method lends itself very well for automatic measurement, and can be extended for future sensor systems that include advanced image processing. The TOD curve can be implemented easily in a TA model such as ACQUIRE. An observer performance study with real targets shows that the TOD curve predicts TA performance better than the MRC does. The method has been implemented successfully in a thermal imager field test apparatus called TIPI, and may be implemented in current MRTD and MRC test equipment with little effort.

  1. Assessment of Spacecraft Operational Status Using Electro-Optical Predictive Techniques

    Science.gov (United States)

    Swann, D.; Klem, B.; McCoy, B.

    2010-09-01

    The current class of small satellite systems presents an analyst responsible for monitoring spacecraft operational status and early detection of detrimental anomalies with a broad variety of sensing and identification issues and challenges. Simple, small, cube-shaped satellites, without protruding solar panel appendages, may require enhanced preflight characterization processes to support monitoring by passive, remote, nonimaging optical sensors. This paper will describe spacecraft optical signature modeling and simulation techniques to develop sensing and identification algorithms for observing and characterizing key spacecraft features. The simulation results are based on electro-optical signatures apparent to nonimaging sensors, along with related observable features derived from multicolor and multiviewing aspect scenarios. This model and simulation analysis capability is used to support programs to monitor spacecraft performance status and identify anomalies associated with spacecraft damage/deterioration due to space debris or micrometeorite impact, thruster exhaust deposition or material aging. The development of state-of-the-art optical signature modeling tools to perform high-fidelity satellite models (such as the Air Force Academy FalconSat-5 or AFRL TacSat-3) simulations to characterize spectral radiant intensities apparent to passive, remote, nonresolved imaging sensors are described in detail. Simulations are performed for a comprehensive scenario range of natural (solar and earth) illumination and viewing conditions. Results are generated for comparing baseline, streamlined geometry models with the actual higher fidelity models that capture vehicle small-size hardware components and modifications. Output consisting of radiant intensity history apparent to ground-based sensor locations for vehicle trajectories that capture a comprehensive range of illumination conditions from the sun and underlying earth scene are presented for extensive spectral band

  2. 2-port internal model control for gyro stabilized platform of electro-optical tracking system

    Science.gov (United States)

    Xia, Yun-xia; Bao, Qi-liang; Li, Zhi-jun; Wu, Qiong-yan

    2012-06-01

    Line-of-sight stabilized system, which can be used to isolate the vibration of the moving bed and the disturbance of environment, is the most important part of an electro-optical tracking system. The steady precision and robustness are the key issues of recent researches. In this paper, a novel control approach so called 2-Port Internal Model Control (2-PIMC) for line-of-sight stabilized system is proposed. By adding a parallel feedback control loop on the basis of Internal Model Control (IMC), the 2-PIMC method can improve precision while it also has strong robustness as the IMC. The robustness and the static error of 2-PIMC method were subsequently analyzed. Based on this novel method, Simulation and experiment are both carried out for a gyro stabilized platform of electro-optical tracking system. The experiments include a shaking table which can generate disturbance as the moving bed and a gyro stabilized platform which is mounted on the shaking table. The experimental result indicated that the gyro stabilized platform using 2-PIMC method is accurate and effective. Comparing with PI control, the following error and disturbance restraining error were both greatly improved at low-frequency and mid-frequency by the 2-PIMC method proposed. The improvement of precision is more than 10dB at 4Hz. In addition, the 2-PIMC method doesn't need any extra sensors for the platform and it's easy for parameters regulation. It can be concluded that the2-PIMC method is a new approach for the high-performance gyro stabilized platform and might have broad application prospect.

  3. Transparent conducting oxide electro-optic modulators on silicon platforms: A comprehensive study based on the drift-diffusion semiconductor model

    Science.gov (United States)

    Sinatkas, Georgios; Pitilakis, Alexandros; Zografopoulos, Dimitrios C.; Beccherelli, Romeo; Kriezis, Emmanouil E.

    2017-01-01

    Electro-optic waveguide modulators exploiting the carrier-induced epsilon-near-zero effect in transparent conducting oxides are comprehensively studied and evaluated using a rigorous multi-physics modeling framework. The examined amplitude modulators integrate indium tin oxide with two representative examples of the silicon-on-insulator technology, the silicon-rib and silicon-slot platform, with the latter design exhibiting superior performance, featuring μm modulation lengths, switching speeds exceeding 100 GHz, and a sub-pJ per bit of energy consumption. The effect of free carriers is rigorously introduced by combining the drift-diffusion model for the description of the carrier dynamics with near-infrared carrier-dependent permittivity models, leading to a seamless and physically consistent integration of solid-state physics and Maxwell wave theory on a unified finite-element platform.

  4. Designing and commissioning of a setup for timing-jitter measurements using electro-optic temporal decoding

    Energy Technology Data Exchange (ETDEWEB)

    Borissenko, Dennis

    2016-12-15

    Precise measurements of the arrival time jitter between the ionization laser, used to create the plasma, and the driver beam in the PWFA setup of the FLASHForward project are of high interest for the operation and optimization of the experiment. In this thesis, an electro-optic temporal decoding (EOTD) setup with near crossed polarizer detection scheme is presented, which can measure the timing-jitter to an accuracy of around 30 fs. This result was obtained during several measurements conducted at the coherent transition radiation beamline CTR141 at FLASH, using a 100 μm thick GaP crystal and coherent diffraction/transition radiation, generated from the FLASH1 electron bunches. Measurements were performed during long and short electron bunch operation at FLASH, showing that best results are obtained with CDR from long electron bunches. Utilizing CTR led to a higher EO signal and ''over-compensation'' of the SHG background level during the measurement, which resulted in a double-peak structure of the observed THz pulses. To resolve the single-cycle nature of these THz pulses, the SHG background had to be adjusted properly. Furthermore, EOTD measurements during a short bunch operation run at FLASH exhibited strong oscillations in the EO signal, which were suspected to come either from internal lattice resonances of the EO crystal or internal reflections, or excitation of water vapor in the humid air in the laboratory. The oscillations spoiled the observed EOTD trace leading to no sensible measurements of the arrival time jitter during this short bunch operation. To evaluate the capabilities of the setup for monitoring the timing jitter of short PWFA accelerated electron bunches or very short driver bunches at FLASHForward, further investigations on the observed oscillations in the EOTD traces have to be performed during short bunch operation at FLASH with different crystals and under vacuum conditions, to understand the oscillations of the EO

  5. Modeling, Simulation, and Characterization of Electro-Optic Polymer Waveguide Devices.

    Science.gov (United States)

    Ma, Jiong

    The primary objective of this thesis is to investigate the properties of optical polymer waveguides and switches, develop a phenomenological CAD tool, and to use this phenomenological tool to design optical polymer devices for high-speed interconnects in VLSI systems. In the investigations of optical polymer waveguides, a new phenomenological bleaching model that is able to predict optical index profiles for photobleached polymer films was developed. The theoretical model shows good agreement with measured results for the effective index and optical field distributions of waveguides, and the absorption of films. Based on this bleaching model, we can predict the index profile for polymer channel waveguides and formulate design rules for active optical switches and modulators. The model has been successfully applied to photobleached PMMA/DR1 and Ultem/DEDR1 waveguides. An experimental technique to determine the poling -induced optical birefringence and optical nonlinearity is also discussed. In this technique, absorption measurements are performed immediately after poling. The poling-induced index changes as a function of wavelength are obtained from the absorption changes using a Kramers-Kronig transformation. An alternative method for predicting the poling-induced index changes, requiring a combination of waveguide measurement techniques and order parameter calculations, exhibits good agreement. By combining the poling effects with the photobleaching index profile, a CAD tool has been developed to calculate the optical field distribution and loss which allows the design of active electro-optical modulators. Using the CAD tool together with an equivalent circuit model of electro-optic polymer switches, circuit level comparisons of a CMOS strip line interconnect with an external polymer modulator interconnect were performed in terms of power dissipation, bandwidth, and connection density. HSPICE was used as a circuit simulation tool. Based on this analysis, it is

  6. Design, synthesis and characterization of novel nonlinear optical chromophores for electro-optical applications

    Science.gov (United States)

    Liu, Feng

    This dissertation involves the design, synthesis and characterization of second order nonlinear optical chromophores for electro-optic applications. The design concept, that poling efficiency and macroscopic nonlinearities can be improved by modifying a chromophore's shape, has been explored. Chapter 1 gives an introduction into theoretical background of nonlinear optics and electro-optic phenomenon in organic molecules and poled polymers. Chapter 2 involves the design and synthesis of GLD-2 and GLD-3 chromophores, both with bulky substituents on the ring-fused bridge. The optical studies and HRS measurement show that the two alkyl groups on the bridge blueshift the lambdamax in chloroform by 20 nm and decrease the beta values. DSC and TGA thermal analysis show Td of GLD-2 and GLD-3 over 240°C. The maximum achievable r33 of GLD-2/PMMA is 61 pm/V, compared to the 92.4 pm/V of GLD-1/PMMA. But GLD-2/APC shows r33 of 45.2pm/V, higher than GLD-1/APC due to the improved compatibility with APC. The optical loss of 13 wt% GLD-2/PMMA at 1.55mum is 1.4 dB compared to the 2.3 dB of 17 wt% GLD-1/PMMA. Optical loss studies prove that adding two bulky substituents on bridge help attenuate electrostatic interactions. GLD-3 show deteriorated solubility in common used organic solvents, probably due to the combination of two TBDMS and two lengthy alkyl groups. Chapter 3 presents synthesis of thiophene-based chromophores with variously positioned TBDMS groups. The optical studies of these chromophores show one TBDMSO substitution on the thiophene bridge yields little influence on the lambda max in chloroform. FTCDS chromophore with two TBDMS groups, one on donor and one on thiophene bridge, shows to be the best structure with regards the thermal stability and achievable maximum EO coefficient value, 65.9 pm/V, at only 24 wt% loading density at 1.3 mum. Chapter 4 deals with three novel bridges for NLO chromophores. Synthetic methodologies of the diketone precursor of rigidified

  7. A single-shot, multiwavelength electro-optic data-acquisition system for inertial confinement fusion applications (invited)

    Energy Technology Data Exchange (ETDEWEB)

    Donaldson, W. R.; Zhao, C.; Ji, L.; Roides, R. G. [Laboratory for Laser Energetics, University of Rochester, Rochester, New York 14623-1299 (United States); Miller, K. [National Security Technology, Santa Barbara, California 93111 (United States); Beeman, B. [Lawrence Livermore National Laboratory, Livermore, California 94550 (United States)

    2012-10-15

    Electro-optic data-acquisition systems encode the output from voltage-history diagnostics onto optical signals. The optical signals can propagate long distances over fiber-optic links without degrading the bandwidth of the encoded signal while protecting the recording electronics from overvoltage damage. The sinusoidal response and tolerance to high-input voltages of the Mach-Zehnder modulator used for the encoding leads to the additional advantage of a high dynamic range and a reduced need for manually swapping attenuators. We have demonstrated a single-shot, electro-optic data-acquisition system with a 600:1 dynamic range. This system provides optical isolation and a bandwidth of 6 GHz. The prototype system uses multiple optical wavelengths to allow for the multiplexing of up to eight signals onto one photodetector.

  8. Mesoporous sol-gel silica cladding for hybrid TiO2/electro-optic polymer waveguide modulators.

    Science.gov (United States)

    Enami, Yasufumi; Kayaba, Yasuhisa; Luo, Jingdong; Jen, Alex K-Y

    2014-06-30

    We report the efficient poling of an electro-optic (EO) polymer in a hybrid TiO(2)/electro-optic polymer multilayer waveguide modulator on mesoporous sol-gel silica cladding. The mesoporous sol-gel silica has nanometer-sized pores and a low refractive index of 1.24, which improves mode confinement in the 400-nm-thick EO polymer film in the modulators and prevents optical absorption from the lower Au electrode, thereby resulting in a lower half-wave voltage of the modulators. The half-wave voltage (Vπ) of the hybrid modulator fabricated on the mesoporous sol-gel silica cladding is 6.0 V for an electrode length (Le) of 5 mm at a wavelength of 1550 nm (VπLe product of 3.0 V·cm) using a low-index guest-host EO polymer (in-device EO coefficient of 75 pm/V).

  9. Electro-optic Mach-Zehnder Interferometer based Optical Digital Magnitude Comparator and 1's Complement Calculator

    Science.gov (United States)

    Kumar, Ajay; Raghuwanshi, Sanjeev Kumar

    2016-06-01

    The optical switching activity is one of the most essential phenomena in the optical domain. The electro-optic effect-based switching phenomena are applicable to generate some effective combinational and sequential logic circuits. The processing of digital computational technique in the optical domain includes some considerable advantages of optical communication technology, e.g. immunity to electro-magnetic interferences, compact size, signal security, parallel computing and larger bandwidth. The paper describes some efficient technique to implement single bit magnitude comparator and 1's complement calculator using the concepts of electro-optic effect. The proposed techniques are simulated on the MATLAB software. However, the suitability of the techniques is verified using the highly reliable Opti-BPM software. It is interesting to analyze the circuits in order to specify some optimized device parameter in order to optimize some performance affecting parameters, e.g. crosstalk, extinction ratio, signal losses through the curved and straight waveguide sections.

  10. Design of 1-bit and 2-bit magnitude comparators using electro-optic effect in Mach-Zehnder interferometers

    Science.gov (United States)

    Kumar, Santosh; Bisht, Ashish; Singh, Gurdeep; Choudhary, Kuldeep; Raina, K. K.; Amphawan, Angela

    2015-12-01

    The Mach-Zehnder interferometer (MZI) structures collectively show powerful capability in switching an input optical signal to a desired output port from a collection of output ports. Hence, it is possible to construct complex optical combinational digital circuits using the electro-optic effect constituting MZI structure as a basic building block. Optical switches have been designed for 1-bit and 2-bit magnitude comparators based on electro-optic effect using Mach-Zehnder interferometers. The paper constitutes a mathematical description of the proposed device and thereafter simulation using MATLAB. Analysis of some factors influencing the performances of proposed device has been discussed properly. The study is verified using beam propagation method.

  11. High Spatial Resolution Electro -Optic Field -Mapping for Three Orthogonal Field Components in a Micro -Structured Electrode

    Institute of Scientific and Technical Information of China (English)

    Yoshiro Matsuo; Tetsuya Kawanishi; Satoshi Oikawa; Kaoru Higuma; Masayuki Izutsu

    2003-01-01

    @@ The optically based technique of electro-optic (EO)sampling has been used for diagnosing the internal high-speed signals of integrated circuits [1]. One of the features that make the EO sampling technique very promising is a minimal probe: the EO sampling technique does not require an electrode and ground plane incorporated as part of a probe so that, compared with conventional metal probes, the invasiveness of an EO probe is minimal.

  12. High Spatial Resolution Electro -Optic Field -Mapping for Three Orthogonal Field Components in a Micro -Structured Electrode

    Institute of Scientific and Technical Information of China (English)

    Yoshiro; Matsuo; Tetsuya; Kawanishi; Satoshi; Oikawa; Kaoru; Higuma; Masayuki; Izutsu

    2003-01-01

    The optically based technique of electro-optic (EO) sampling has been used for diagnosing the internal high-speed signals of integrated circuits.One of the features that make the EO sampling technique very promising is a minimal probe: the EO sampling technique does not require an electrode and ground plane incorporated as part of a probe so that, compared with conventional metal probes, the invasiveness of an EO probe is minimal.

  13. [Progress of electro-optic polymer in the field of generation and detection of Terahertz waves by all-optical technique].

    Science.gov (United States)

    Wang, Xuan; Jiang, Qiang; Wang, Yue; Zhang, Wen-long; Li, Zhi-yuan

    2014-08-01

    Research on and development of the high amplitude, broadband terahertz system based on ultra-short pulse, low-power laser system is a hot spot in the field of terahertz. So far, for all the reported THz bandwidths broader than 10 THz, there always exist strong dispersion and absorption gaps associated with the lattice resonance in either the photoconductive materials or crystalline EO materials. If such THz sources and detectors are employed in spectroscopic studies, spectral information in these gaps cannot be extracted. One of the advantages of using amorphous electro-optic polymer films as THz emitters and sensors is that there is no dispersion or absorption resulting from the lattice resonance effect, making a gap-free THz spectrum possible. Another advantage of electro-optic polymer films is the ease of fabrication and handling, in contrast to the extremely thin crystalline electro-optic materials used for existing broadband THz system. In addition, we can engineer the electro-optic polymeric materials to achieve small phase mismatch and high electro-optic coefficients such that brightness and broad bandwidth of THz radiation can be obtained. In this thesis a theoretical description of electro-optic effect based on electro-optic polymer and the second- order nonlinear chromophores synthesis is reviewed. In the past 20 years, progress in electro-optic polymer in the field of generating and detecting terahertz radiation by all-optical techniques is summarized, including the terahertzs systems based on copolymer and the guest-host polymer induced by Titanium doped sapphire femtosecond laser and based on the guest-host polymer at communication wavelengths.

  14. A systematic optimization of design parameters in strained silicon waveguides to further enhance the linear electro-optic effect

    Science.gov (United States)

    Olivares, Irene; Angelova, Todora I.; Pinilla-Cienfuegos, Elena; Sanchis, Pablo

    2016-05-01

    The electro-optic Pockels effect may be generated in silicon photonics structures by breaking the crystal symmetry by means of a highly stressing cladding layer (typically silicon nitride, SiN) deposited on top of the silicon waveguide. In this work, the influence of the waveguide parameters on the strain distribution and its overlap with the optical mode to enhance the Pockels effect has been analyzed. The optimum waveguide structure have been designed based on the definition and quantification of a figure of merit. The fabrication of highly stressing SiN layers by PECVD has also been optimized to characterize the designed structures. The residual stress has been controlled during the growth process by analyzing the influence of the main deposition parameters. Therefore, two identical samples with low and high stress conditions were fabricated and electro-optically characterized to test the induced Pockels effect and the influence of carrier effects. Electro-optical modulation was only measured in the sample with the high stressing SiN layer that could be attributed to the Pockels effect. Nevertheless, the influence of carriers were also observed thus making necessary additional experiments to decouple both effects.

  15. Optimized design and fabrication of nanosecond response electro optic switch based on ultraviolet-curable polymers

    Institute of Scientific and Technical Information of China (English)

    赵旭亮; 岳远斌; 刘通; 孙健; 王希斌; 孙小强; 陈长鸣; 张大明

    2015-01-01

    A nanosecond response waveguide electro-optic (EO) switch based on ultraviolet (UV) sensitive polymers of Norland optical adhesive (NOA73) and Dispersed Red 1 (DR1) doped SU-8 (DR1/SU-8) is designed and fabricated. The absorption properties, refractive indexes, and surface morphologies of NOA73 film are characterized. The single-mode transmission condition is computed by the effective index method, and the percentage of optical field distributed in EO layer is optimized to be 93.78%. By means of spin-coating, thermal evaporation, photolithography, and inductively coupled plasma etching, a Mach–Zehnder inverted-rib waveguide EO switch with micro-strip line electrode is fabricated on a silicon substrate. Scanning electron microscope characterization proves the physic-chemical compatibility between NOA73 cladding and DR1/SU-8 core material. The optical transmission loss of the fabricated switch is measured to be 2.5 dB/cm. The rise time and fall time of switching are 3.199 ns and 2.559 ns, respectively. These results indicate that the inverted-rib wave-guide based on UV-curable polymers can effectively reduce the optical transmission loss and improve the time response performance of an EO switch.

  16. Multi-Site Simultaneous Time-Resolved Photometry with a Low Cost Electro-Optics System

    Directory of Open Access Journals (Sweden)

    Forrest Gasdia

    2017-05-01

    Full Text Available Sunlight reflected off of resident space objects can be used as an optical signal for astrometric orbit determination and for deducing geometric information about the object. With the increasing population of small satellites and debris in low Earth orbit, photometry is a powerful tool in operational support of space missions, whether for anomaly resolution or object identification. To accurately determine size, shape, spin rate, status of deployables, or attitude information of an unresolved resident space object, multi-hertz sample rate photometry is required to capture the relatively rapid changes in brightness that these objects can exhibit. OSCOM, which stands for Optical tracking and Spectral characterization of CubeSats for Operational Missions, is a low cost and portable telescope system capable of time-resolved small satellite photometry, and is field deployable on short notice for simultaneous observation from multiple sites. We present the electro-optical design principles behind OSCOM and light curves of the 1.5 U DICE-2 CubeSat and simultaneous observations of the main body of the ASTRO-H satellite after its fragmentation event.

  17. Multi-Sensor Fusion of Infrared and Electro-Optic Signals for High Resolution Night Images

    Directory of Open Access Journals (Sweden)

    Victor Lawrence

    2012-07-01

    Full Text Available Electro-optic (EO image sensors exhibit the properties of high resolution and low noise level at daytime, but they do not work in dark environments. Infrared (IR image sensors exhibit poor resolution and cannot separate objects with similar temperature. Therefore, we propose a novel framework of IR image enhancement based on the information (e.g., edge from EO images, which improves the resolution of IR images and helps us distinguish objects at night. Our framework superimposing/blending the edges of the EO image onto the corresponding transformed IR image improves their resolution. In this framework, we adopt the theoretical point spread function (PSF proposed by Hardie et al. for the IR image, which has the modulation transfer function (MTF of a uniform detector array and the incoherent optical transfer function (OTF of diffraction-limited optics. In addition, we design an inverse filter for the proposed PSF and use it for the IR image transformation. The framework requires four main steps: (1 inverse filter-based IR image transformation; (2 EO image edge detection; (3 registration; and (4 blending/superimposing of the obtained image pair. Simulation results show both blended and superimposed IR images, and demonstrate that blended IR images have better quality over the superimposed images. Additionally, based on the same steps, simulation result shows a blended IR image of better quality when only the original IR image is available.

  18. Development and characterization of thermally stable electro-optic polymers and devices (Presentation Recording)

    Science.gov (United States)

    Otomo, Akira; Aoki, Isao; Yamada, Chiyumi; Yamada, Toshiki

    2015-10-01

    Electro-optic (EO) polymers are key materials for next generation optical communications not only in wide area network but also in local area and storage area network because EO polymer modulator can be operated at fast speed more than 100 GHz with low energy consumption and can be miniaturized in combination with silicon photonics. In practical applications, thermal stability is one of the important issues to be considered for developing EO polymers. Since EO activity of the polymer is proportional to dipole orientation factor of the EO moieties, electric field assisted poling around glass transition temperature (Tg) of the polymer is necessary. However, the poled order of the molecules relaxes gradually at finite temperature, and then EO activity decreases after long period of time. We have successfully developed thermally stable EO polymers that have high-Tg up to 180 °C. They show excellent thermal stability with the Telcordia thermal test. Thermal stability is also characterized by thermally stimulated depolarization current (TSDC) measurement. Analyzing the TSDC, we can estimate the activation energy and relaxation time of polarization at any temperature. We will discuss thermal stability of the high-Tg EO polymers and devices.

  19. Quasi-phase-matched electro-optic modulators for high-speed signal processing

    Science.gov (United States)

    Toney, James E.; Stenger, Vincent E.; Busch, James; Pontius, Peter; Clabough, Michael; Pollick, Andrea; Sriram, Sri

    2013-01-01

    This paper reports on the design, fabrication and testing of quasi-phase-matched (QPM) lithium niobate electro-optic modulators optimized for the 40-60 GHz frequency range. The device used a single-drive, coplanar-waveguide (cpw) electrode structure that provided a good balance between impedance and RF loss, and a DC Vπ.L product of approximately 10 V.cm. Ferroelectric domain engineering enabled push-pull operation with a single drive, while achieving low chirp. A custom developed pulsed poling process was used to fabricate periodic domain QPM structures in lithium niobate. QPM periods were in the range of 3 mm to 4.5 mm, depending on the design frequency. The pulse method enabled precise domain definition with a minimum of overpoling. Low-loss diffused optical waveguides were fabricated by an annealed proton exchange (APE) process. By operating in both co-propagating and counter-propagating modes, the QPM devices can be used to implement dual band RF bandpass filters simultaneously covering both 10-20 GHz and 40-60 GHz frequency bands. Arrays of QPM device structures demonstrated in this work form the basis for a reconfigurable RF photonic filter. The RF photonic QPM technology enables efficient concurrent antenna remoting and filtering functionality. Applications of the technology include fiber radio for cellular access and finite impulse response filters for wideband electronic warfare receivers.

  20. Damage analysis of CMOS electro-optical imaging system by a continuous wave laser

    Science.gov (United States)

    Yoon, Sunghee; Jhang, Kyung-Young; Shin, Wan-Soon

    2016-08-01

    EOIS (electro-optical imaging system) is vulnerable to laser beam because EOIS focuses the incident laser beam onto the image sensor via lens module. Accordingly, the laser-induced damage of EOIS is necessary to be identified for the counter-measure against the laser attack. In this study, the damage of CMOS EOIS and image sensor induced by CW (continuous wave) NIR (near infrared) laser was experimentally investigated. When the laser was emitted to CMOS EOIS, a temporary damage was occurred first such as flickering or dazzling and then a permanent damage was followed as the increase of laser irradiance and irradiation time. If the EIOS is composed of the optical equipment made of heatresistant material, laser beam can penetrate the lens module of EOIS without melting the lens and lens guide. Thus, it is necessary to investigate the damage of CMOS image sensor by the CW laser and we performed experimentally investigation of damage on the CMOS image sensor similar with case of CMOS EOIS. And we analyzed the experiment results by using OM (optical microscopy) and check the image quality through tomography. As the increase of laser irradiance and irradiation time, the permanent damage such as discoloration and breakdown were sequentially appeared.

  1. Optimization design of optical waveguide in Mach-Zehnder electro-optical polymer modulator

    Institute of Scientific and Technical Information of China (English)

    GAO Yuan; ZHANG Xiao-xia; LIAO Jin-kun

    2011-01-01

    @@ In order to reduce transmission loss of the optical waveguide in Mach-Zehnder (M-Z) electro-optical (EO) polymer modulator,the basic iterative formula of semi-vector finite-difference beam propagation method (FD-BPM) is obtained from the scalar wave equation.The transition waveguide is combined with S-type bend branch waveguide for the M-Z EO modulator in the branch waveguide.The effects of structure parameters such as ridge width, length of the branch waveguide and interferometer spacing on the transmission loss are systematically studied by using the semi-vector FD-BPM method.The structure is optimized as an S-sine bend branch waveguide, with rib width w=7 μm, length of branch waveguide L=1200μm and interferometer spacing G=22 μm.The results show that the optimized structure can reduce transmission loss to 0.083 dB,which have a certain reference value to the design of optical waveguide in M-Z polymer modulator.

  2. Measurement of the linear electro-optic tensor of cubic boron nitride single crystals

    Institute of Scientific and Technical Information of China (English)

    Shuang Wang; Gang Jia; Xiuhuan Liu; Shipeng Chi; Jingcheng Zhu; Yanjun Gao; Pingwei Zhou; Zhanguo Chen

    2012-01-01

    The transverse electro-optic (EO) modulation system is built based on cubic boron nitride (cBN) single crystals unintentionally doped and synthesized at a high pressure and high temperature.The photoelectric output of the system includes two parts that can be measured respectively and the value of elements in the linear EO tensor of the cBN crystal can be obtained.This method does not need to measure the absolute light intensity.All of the surfaces of the tiny cBN crystals whose hardness is next to the hardest diamonds are {111} planes.The rectangular parallelepiped cBN samples are obtained by cleaving along {110} planes and subsequently grinding and polishing {112} planes of the tiny octahedral cBN flakes.Three identical non-zero elements of the EO tensor of the cBN crystal are measured via two sample configurations,and the measured results are very close,about 3.68 and 3.95 pm/V,respectively,which are larger than the linear EO coefficients of the general Ⅲ-Ⅴ compounds.

  3. Dielectric and electro-optic measurements of nematic liquid crystals doped with carbon nanotubes

    Science.gov (United States)

    Peterson, Matthew; Georgiev, Georgi; Atherton, Timothy; Cebe, Peggy

    We studied the effects of carbon nanotubes (CNTs) on the dielectric and electro-optic properties of nematic 5CB liquid crystals (LCs). Samples containing 0.01%, 0.10% and 1.00% CNTs by weight were prepared. Anti- parallel rubbed cells with a nominal thickness of 10 μm were prepared using indium tin oxide coated glass cells and a polyimide alignment layer. The capacitance and dissipation factor were measured using an Agilent 4284A precision LCR meter. From these measurements, the complex dielectric permittivity was determined as a function of frequency. Analysis of the low frequency regime (f <1000 Hz) indicates that 5CB samples containing CNTs have a higher conductance than neat samples. The Fréedericksz transition critical voltage was noted by a sharp increase in capacitance after an initial plateau. Numerical simulations of CNT-facilitated switching show that polarization induced on the nanotubes from capacitive effects can significantly reduce the critical voltage in DC electric fields, in agreement with experimental results. Measurements of the critical voltage over a range of frequencies will also be presented. Research was supported by the National Science Foundation, DMR1206010.

  4. Bandwidth manipulation of quantum light by an electro-optic time lens

    Science.gov (United States)

    Karpiński, Michał; Jachura, Michał; Wright, Laura J.; Smith, Brian J.

    2017-01-01

    The ability to manipulate the spectral-temporal waveform of optical pulses has enabled a wide range of applications from ultrafast spectroscopy to high-speed communications. Extending these concepts to quantum light has the potential to enable breakthroughs in optical quantum science and technology. However, filtering and amplifying often employed in classical pulse shaping techniques are incompatible with non-classical light. Controlling the pulsed mode structure of quantum light requires efficient means to achieve deterministic, unitary manipulation that preserves fragile quantum coherences. Here, we demonstrate an electro-optic method for modifying the spectrum of non-classical light by employing a time lens. In particular, we show highly efficient, wavelength-preserving, sixfold compression of single-photon spectral intensity bandwidth, enabling over a twofold increase of single-photon flux into a spectrally narrowband absorber. These results pave the way towards spectral-temporal photonic quantum information processing and facilitate interfacing of different physical platforms where quantum information can be stored or manipulated.

  5. Fundamental limits on the electro-optic device figure of merit

    CERN Document Server

    Mossman, Sean; Kuzyk, Mark G

    2016-01-01

    Device figures of merit are commonly employed to assess bulk material properties for a particular device class, yet these properties ultimately originate in the linear and nonlinear susceptibilities of the material which are not independent of each other. In this work, we calculate the electro-optic device figure of merit based on the half-wave voltage and linear loss, which is important for phase modulators and serves as the simplest example of the approach. This figure of merit is then related back to the microscopic properties in the context of a dye-doped polymer, and its fundamental limits are obtained to provide a target. Surprisingly, the largest figure of merit is not always associated with a large nonlinear-optical response, the quantity that is most often the focus of optimization. An important lesson to materials design is that the figure of merit alone should be optimized. The best device materials can have low nonlinearity provided that the loss is low; or, near resonance high loss may be desirab...

  6. Electro-optic metal-insulator-semiconductor-insulator-metal Mach-Zehnder plasmonic modulator

    Science.gov (United States)

    Thomas, Roney; Ikonic, Zoran; Kelsall, Robert W.

    2012-01-01

    The performance of a CMOS-compatible electro-optic Mach-Zehnder plasmonic modulator is investigated using electromagnetic and carrier transport simulations. Each arm of the Mach-Zehnder device comprises a metal-insulator-semiconductor-insulator-metal (MISIM) structure on a buried oxide substrate. Quantum mechanical effects at the oxide/semiconductor interfaces were considered in the calculation of electron density profiles across the structure, in order to determine the refractive index distribution and its dependence on applied bias. This information was used in finite element simulations of the electromagnetic modes within the MISIM structure in order to determine the Mach-Zehnder arm lengths required to achieve destructive interference and the corresponding propagation loss incurred by the device. Both inversion and accumulation mode devices were investigated, and the layer thicknesses and height were adjusted to optimise the device performance. A device loss of <8 dB is predicted for a MISIM structure with a 25 nm thick silicon layer, for which the device length is <3 μm, and <5 dB loss is predicted for the limiting case of a 5 nm thick silicon layer in a 1.2 μm long device: in both cases, the maximum operating voltage is 7.5 V.

  7. Single-shot time-resolved THz spectroscopy using non-collinear electro-optic imaging

    Science.gov (United States)

    Wang, Zhenyou; Su, Fuhai; Hegmann, Frank A.

    2010-03-01

    We demonstrate a technique for rapid substance identification via single-shot, coherent THz imaging using non-collinear electro-optic sampling. A THz probe pulse generated in ZnTe is transmitted through the sample then focused on a (110) ZnTe detection crystal. An 800nm, 100fs optical pulse employed as a sampling beam passes through the ZnTe detection crystal at an angle of 7^o relative to the THz beam.footnotetextT. Yasuda et al., Opt. Commun. 267, 128 (2006) The THz field induced birefringence is resolved as a variation of the intensity of the sampling pulse transmitted through a crossed polarizer. The modified sampling beam spot is imaged using a CCD camera. Because of the non-collinear geometry, the spatial overlap between the THz field and the optical pulse depends on the temporal position within the THz waveform. Consequently, we obtain high-resolution 2D images of the THz waveform without scanning the relative path length. The resolution of the absorption spectra extracted from wet paper and lactose using the single-shot imaging approach is comparable to the resolution obtained through conventional scanning lock-in measurements. Possible applications for substance detection are discussed.

  8. Electro-optic delay oscillator with nonlocal nonlinearity: Optical phase dynamics, chaos, and synchronization.

    Science.gov (United States)

    Lavrov, Roman; Peil, Michael; Jacquot, Maxime; Larger, Laurent; Udaltsov, Vladimir; Dudley, John

    2009-08-01

    We demonstrate experimentally how nonlinear optical phase dynamics can be generated with an electro-optic delay oscillator. The presented architecture consists of a linear phase modulator, followed by a delay line, and a differential phase-shift keying demodulator (DPSK-d). The latter represents the nonlinear element of the oscillator effecting a nonlinear transformation. This nonlinearity is considered as nonlocal in time since it is ruled by an intrinsic differential delay, which is significantly greater than the typical phase variations. To study the effect of this specific nonlinearity, we characterize the dynamics in terms of the dependence of the relevant feedback gain parameter. Our results reveal the occurrence of regular GHz oscillations (approximately half of the DPSK-d free spectral range), as well as a pronounced broadband phase-chaotic dynamics. Beyond this, the observed dynamical phenomena offer potential for applications in the field of microwave photonics and, in particular, for the realization of novel chaos communication systems. High quality and broadband phase-chaos synchronization is also reported with an emitter-receiver pair of the setup.

  9. TADPOLE for longitudinal electron-bunch diagnostics based on electro-optic upconversion

    Energy Technology Data Exchange (ETDEWEB)

    Schwinkendorf, Jan-Patrick, E-mail: jan-patrick.schwinkendorf@desy.de; Wunderlich, Steffen, E-mail: steffen.wunderlich@desy.de; Schaper, Lucas; Schmidt, Bernhard; Osterhoff, Jens

    2014-03-11

    Electron-bunch diagnostics are desired to utilize unambiguous, non-destructive, single-shot techniques. Various methods fulfill the latter two demands, but feature significant ambiguities and constraints in the reconstruction of time-domain electron-bunch profiles, e.g. uncertainties arising from the phase retrieval of coherent radiation using the Kramers–Kronig relation. We present a novel method of measuring the spectral phase. The measurement is based on upconversion in an electro-optic crystal, where the THz-field spectrum of fs-electron bunches is shifted to the near-infrared. This technique allows the single-shot detection of its longitudinal form factor in both, amplitude and phase. The spectral phase and amplitude information is measured and thus the temporal profile reconstructed using temporal analysis by dispersing a pair of light E-fields, also known as TADPOLE. This is a combination of frequency resolved optical gating (FROG) and spectral interferometry, enabling the temporal measurement of low-power laser pulses. In this procedure, a narrow-bandwidth laser pulse detecting the longitudinal variations in the transverse electric field of an electron bunch via frequency mixing is interfered with a broadband and FROG-characterized reference pulse. The longitudinal beam profile may therefore be unambiguously inferred from the generated interferogram and the detected spectral-phase-information of the reference pulse.

  10. TADPOLE for longitudinal electron-bunch diagnostics based on electro-optic upconversion

    Energy Technology Data Exchange (ETDEWEB)

    Schwinkendorf, Jan-Patrick; Wunderlich, Steffen; Schmidt, Bernhard; Osterhoff, Jens [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany)

    2013-07-01

    Electron-bunch diagnostics are desired to utilize unambiguous, non-destructive, single-shot techniques. Various methods fulfill the latter two demands, but feature significant ambiguities and constraints in the reconstruction of a time-domain electron-bunch profile, as for example uncertainties due to the phase retrieval of coherent radiation using the Kramers-Kronig relation. We present a novel method of upconverting the THz-field spectrum of fs electron bunches at the free-electron laser FLASH into the near-infrared in an electro-optic crystal. This technique allows the single-shot detection of its longitudinal form factor in both, amplitude and phase. The spectral phase and amplitude information is measured and thus the temporal profile reconstructed using temporal analysis by dispersing a pair of light E-fields, also known as TADPOLE. This is a combination of frequency resolved optical gating (FROG) and spectral interferometry, which enables the temporal measurement of low-power laser pulses. In this experiment, a narrow-bandwidth laser pulse detecting the longitudinal electric field of an electron bunch is interfered with a broadband and FROG-characterized reference pulse. The longitudinal beam profile may therefore be unambiguously inferred from the generated interferogram and the detected spectral-phase-information of the reference pulse.

  11. Multi-Site Simultaneous Time-Resolved Photometry with a Low Cost Electro-Optics System.

    Science.gov (United States)

    Gasdia, Forrest; Barjatya, Aroh; Bilardi, Sergei

    2017-05-30

    Sunlight reflected off of resident space objects can be used as an optical signal for astrometric orbit determination and for deducing geometric information about the object. With the increasing population of small satellites and debris in low Earth orbit, photometry is a powerful tool in operational support of space missions, whether for anomaly resolution or object identification. To accurately determine size, shape, spin rate, status of deployables, or attitude information of an unresolved resident space object, multi-hertz sample rate photometry is required to capture the relatively rapid changes in brightness that these objects can exhibit. OSCOM, which stands for Optical tracking and Spectral characterization of CubeSats for Operational Missions, is a low cost and portable telescope system capable of time-resolved small satellite photometry, and is field deployable on short notice for simultaneous observation from multiple sites. We present the electro-optical design principles behind OSCOM and light curves of the 1.5 U DICE-2 CubeSat and simultaneous observations of the main body of the ASTRO-H satellite after its fragmentation event.

  12. Design and investigation of a novel silicon/ferroelectric hybrid electro-optical microring modulator

    Science.gov (United States)

    Qi, Zhipeng; Hu, Guohua; Liu, Chang; Li, Lei; Yun, Binfeng; Zhang, Ruohu; Cui, Yiping

    2017-02-01

    A silicon (Si) and lanthanum-doped lead zirconium titanate (PLZT) hybrid microring modulator based on silicon-on-insulator (SOI) platform is designed theoretically and investigated numerically in this paper. The heterogeneous integration of PLZT film with Si material enables the waveguide to acquire both excellent electro-optical property and strong mode confinement capacity. Such hybrid microring modulator (100 μm in radius) has a PLZT rib-loaded cladding and is integrated with optimized tuning electrodes. The simulation results demonstrated that the Si/PLZT hybrid microring modulator could operate at 14 GHz with a relative high modulation efficiency (<0.8 V cm), which is much better than the other proposed Si/ferroelectric modulators. Meanwhile, under a driving voltage of 20 V, our modulator exhibits an extinction ratio of 32 dB at 1550.22 nm wavelength and a resonant wavelength tunability of 25 pm/V for TE mode. With these outstanding performances, the Si/PLZT hybrid microring modulator holds a great potential as a reliable on-chip device for optical communications and links.

  13. One-dimensional photonic crystal slot waveguide for silicon-organic hybrid electro-optic modulators.

    Science.gov (United States)

    Yan, Hai; Xu, Xiaochuan; Chung, Chi-Jui; Subbaraman, Harish; Pan, Zeyu; Chakravarty, Swapnajit; Chen, Ray T

    2016-12-01

    In an on-chip silicon-organic hybrid electro-optic (EO) modulator, the mode overlap with EO materials, in-device effective r33, and propagation loss are among the most critical factors that determine the performance of the modulator. Various waveguide structures have been proposed to optimize these factors, yet there is a lack of comprehensive consideration on all of them. In this Letter, a one-dimensional (1D) photonic crystal (PC) slot waveguide structure is proposed that takes all these factors into consideration. The proposed structure takes advantage of the strong mode confinement within a low-index region in a conventional slot waveguide and the slow-light enhancement from the 1D PC structure. Its simple geometry makes it robust to resist fabrication imperfections and helps reduce the propagation loss. Using it as a phase shifter in a Mach-Zehnder interferometer structure, an integrated silicon-organic hybrid EO modulator was experimentally demonstrated. The observed effective EO coefficient is as high as 490 pm/V. The measured half-wave voltage and length product is less than 1  V·cm and can be further improved. A potential bandwidth of 61 GHz can be achieved and further improved by tailoring the doping profile. The proposed structure offers a competitive novel phase-shifter design, which is simple, highly efficient, and with low optical loss, for on-chip silicon-organic hybrid EO modulators.

  14. Miniaturized Low-power Electro-optic Modulator Based on Silicon Integrated Nanophotonics and Organic Polymers

    CERN Document Server

    Zhang, Xingyu; Luo, Jingdong; Jen, Alex K -Y; Chen, Ray T

    2014-01-01

    We design and demonstrate a compact, low-power, low-dispersion and broadband optical modulator based on electro-optic (EO) polymer refilled silicon slot photonic crystal waveguide (PCW). The EO polymer is engineered for large EO activity and near-infrared transparency. The half-wave switching-voltage is measured to be V{\\pi}=0.97V over optical spectrum range of 8nm, corresponding to a record-high effective in-device r33 of 1190pm/V and V{\\pi} L of 0.291Vmm in a push-pull configuration. Excluding the slow-light effect, we estimate the EO polymer is poled with an ultra-high efficiency of 89pm/V in the slot. In addition, to achieve high-speed modulation, silicon PCW is selectively doped to reduce RC time delay. The 3-dB RF bandwidth of the modulator is measured to be 11GHz, and a modulation response up to 40GHz is observed.

  15. Complexity in electro-optic delay dynamics: modelling, design and applications.

    Science.gov (United States)

    Larger, Laurent

    2013-09-28

    Nonlinear delay dynamics have found during the last 30 years a particularly prolific exploration area in the field of photonic systems. Besides the popular external cavity laser diode set-ups, we focus in this article on another experimental realization involving electro-optic (EO) feedback loops, with delay. This approach has strongly evolved with the important technological progress made on broadband photonic and optoelectronic devices dedicated to high-speed optical telecommunications. The complex dynamical systems performed by nonlinear delayed EO feedback loop architectures were designed and explored within a huge range of operating parameters. Thanks to the availability of high-performance photonic devices, these EO delay dynamics led also to many successful, efficient and diverse applications, beyond the many fundamental questions raised from the observation of experimental behaviours. Their chaotic motion allowed for a physical layer encryption method to secure optical data, with a demonstrated capability to operate at the typical speed of modern optical telecommunications. Microwave limit cycles generated in similar EO delay oscillators showed significantly improved spectral purity thanks to the use of a very long fibre delay line. Last but not least, a novel brain inspired computational principle has been recently implemented physically in photonics for the first time, again on the basis of an EO delay dynamical system. In this latter emerging application, the computed result is obtained by a proper 'read-out' of the complex nonlinear transients emerging from a fixed point, the transient being issued by the injection of the information signal to be processed.

  16. Spatial and temporal variability in response to hybrid electro-optical stimulation

    Science.gov (United States)

    Duke, Austin R.; Lu, Hui; Jenkins, Michael W.; Chiel, Hillel J.; Jansen, E. Duco

    2012-06-01

    Hybrid electro-optical neural stimulation is a novel paradigm combining the advantages of optical and electrical stimulation techniques while reducing their respective limitations. However, in order to fulfill its promise, this technique requires reduced variability and improved reproducibility. Here we used a comparative physiological approach to aid the further development of this technique by identifying the spatial and temporal factors characteristic of hybrid stimulation that may contribute to experimental variability and/or a lack of reproducibility. Using transient pulses of infrared light delivered simultaneously with a bipolar electrical stimulus in either the marine mollusk Aplysia californica buccal nerve or the rat sciatic nerve, we determined the existence of a finite region of excitability with size altered by the strength of the optical stimulus and recruitment dictated by the polarity of the electrical stimulus. Hybrid stimulation radiant exposures yielding 50% probability of firing (RE50) were shown to be negatively correlated with the underlying changes in electrical stimulation threshold over time. In Aplysia, but not in the rat sciatic nerve, increasing optical radiant exposures (J cm-2) beyond the RE50 ultimately resulted in inhibition of evoked potentials. Accounting for the sources of variability identified in this study increased the reproducibility of stimulation from 35% to 93% in Aplysia and 23% to 76% in the rat with reduced variability.

  17. Highly Linear, Broadband Optical Modulator Based on Electro-optic Polymer

    CERN Document Server

    Zhang, Xingyu; Lin, Che-yun; Wang, Alan X; Hosseini, Amir; Chen, Ray T

    2014-01-01

    In this paper, we present the design, fabrication and characterization of a traveling wave directional coupler modulator based on electro-optic polymer, which is able to provide both high linearity and broad bandwidth. The high linearity is realized by introducing domain-inversion technique in the two-domain directional coupler. A travelling wave electrode is designed to function with bandwidth-length product of 302GHz cm, by achieving low microwave loss, excellent impedance matching and velocity matching, as well as smooth electric field profile transformation. The 3-dB bandwidth of the device is measured to be 10GHz. The spurious free dynamic range of about 110dB Hz^(2/3) is measured over the modulation frequency range 2-8GHz. To the best of our knowledge, such high linearity is first measured at the frequency up to 8GHz. In addition, a 1-to-2 multi-mode interference 3dB-splitter, a photobleached refractive index taper and a quasi-vertical taper are used to reduce the optical insertion loss of the device.

  18. Exploring electro-optic effect of impurity doped quantum dots in presence of Gaussian white noise

    Science.gov (United States)

    Pal, Suvajit; Ganguly, Jayanta; Saha, Surajit; Ghosh, Manas

    2016-01-01

    We explore the profiles of electro-optic effect (EOE) of impurity doped quantum dots (QDs) in presence and absence of noise. We have invoked Gaussian white noise in the present study. The quantum dot is doped with Gaussian impurity. Noise has been administered to the system additively and multiplicatively. A perpendicular magnetic field acts as a confinement source and a static external electric field has been applied. The EOE profiles have been followed as a function of incident photon energy when several important parameters such as electric field strength, magnetic field strength, confinement energy, dopant location, relaxation time, Al concentration, dopant potential, and noise strength possess different values. In addition, the role of mode of application of noise (additive/multiplicative) on the EOE profiles has also been scrutinized. The EOE profiles are found to be adorned with interesting observations such as shift of peak position and maximization/minimization of peak intensity. However, the presence of noise and also the pathway of its application bring about rich variety in the features of EOE profiles through some noticeable manifestations. The observations indicate possibilities of harnessing the EOE susceptibility of doped QD systems in presence of noise.

  19. Resonator-Based Silicon Electro-Optic Modulator with Low Power Consumption

    Science.gov (United States)

    Xin, Maoqing; Danner, Aaron J.; Eng Png, Ching; Thor Lim, Soon

    2009-04-01

    This paper demonstrates, via simulation, an electro-optic modulator based on a subwavelength Fabry-Perot resonator cavity with low power consumption of 86 µW/µm. This is, to the best of our knowledge, the lowest power reported for silicon photonic bandgap modulators. The device is modulated at a doped p-i-n junction overlapping the cavity in a silicon waveguide perforated with etched holes, with the doping area optimized for minimum power consumption. The surface area of the entire device is only 2.1 µm2, which compares favorably to other silicon-based modulators. A modulation speed of at least 300 MHz is detected from the electrical simulator after sidewall doping is introduced which is suitable for sensing or fiber to the home (FTTH) technologies, where speed can be traded for low cost and power consumption. The device does not rely on ultra-high Q, and could serve as a sensor, modulator, or passive filter with built-in calibration.

  20. Fast Interrogation of Fiber Bragg Gratings with Electro-Optical Dual Optical Frequency Combs.

    Science.gov (United States)

    Posada-Roman, Julio E; Garcia-Souto, Jose A; Poiana, Dragos A; Acedo, Pablo

    2016-11-26

    Optical frequency combs (OFC) generated by electro-optic modulation of continuous-wave lasers provide broadband coherent sources with high power per line and independent control of line spacing and the number of lines. In addition to their application in spectroscopy, they offer flexible and optimized sources for the interrogation of other sensors based on wavelength change or wavelength filtering, such as fiber Bragg grating (FBG) sensors. In this paper, a dual-OFC FBG interrogation system based on a single laser and two optical-phase modulators is presented. This architecture allows for the configuration of multimode optical source parameters such as the number of modes and their position within the reflected spectrum of the FBG. A direct read-out is obtained by mapping the optical spectrum onto the radio-frequency spectrum output of the dual-comb. This interrogation scheme is proposed for measuring fast phenomena such as vibrations and ultrasounds. Results are presented for dual-comb operation under optimized control. The optical modes are mapped onto detectable tones that are multiples of 0.5 MHz around a center radiofrequency tone (40 MHz). Measurements of ultrasounds (40 kHz and 120 kHz) are demonstrated with this sensing system. Ultrasounds induce dynamic strain onto the fiber, which generates changes in the reflected Bragg wavelength and, hence, modulates the amplitude of the OFC modes within the reflected spectrum. The amplitude modulation of two counterphase tones is detected to obtain a differential measurement proportional to the ultrasound signal.

  1. Laser-based satellite communication systems stabilized by non-mechanical electro-optic scanners

    Science.gov (United States)

    Ziemkiewicz, Michael; Davis, Scott R.; Rommel, Scott D.; Gann, Derek; Luey, Benjamin; Gamble, Joseph D.; Anderson, Mike

    2016-05-01

    Laser communications systems provide numerous advantages for establishing satellite-to-ground data links. As a carrier for information, lasers are characterized by high bandwidth and directionality, allowing for fast and secure transfer of data. These systems are also highly resistant to RF influences since they operate in the infrared portion of the electromagnetic spectrum, far from radio bands. In this paper we will discuss an entirely non-mechanical electro-optic (EO) laser beam steering technology, with no moving parts, which we have used to form robust 400 Mbps optical data connections through air. This technology will enable low cost, compact, and rugged free space optical (FSO) communication modules for small satellite applications. The EO beam-steerer at the heart of this system is used to maintain beam pointing as the satellite orbits. It is characterized by extremely low values for size, weight and power consumption (SWaP) - approximately 300 cm3, 300 g, and 5 W respectively, which represents a marked improvement compared to heavy, and power-consuming gimbal mechanisms. It is capable of steering a 500 mW, 1 mm short wave infrared (SWIR) beam over a field of view (FOV) of up to 50° x 15°, a range which can be increased by adding polarization gratings, which provide a coarse adjust stage at the EO beam scanner output. We have integrated this device into a communication system and demonstrated the capability to lock on and transmit a high quality data stream by modulation of SWIR power.

  2. Fast Interrogation of Fiber Bragg Gratings with Electro-Optical Dual Optical Frequency Combs

    Directory of Open Access Journals (Sweden)

    Julio E. Posada-Roman

    2016-11-01

    Full Text Available Optical frequency combs (OFC generated by electro-optic modulation of continuous-wave lasers provide broadband coherent sources with high power per line and independent control of line spacing and the number of lines. In addition to their application in spectroscopy, they offer flexible and optimized sources for the interrogation of other sensors based on wavelength change or wavelength filtering, such as fiber Bragg grating (FBG sensors. In this paper, a dual-OFC FBG interrogation system based on a single laser and two optical-phase modulators is presented. This architecture allows for the configuration of multimode optical source parameters such as the number of modes and their position within the reflected spectrum of the FBG. A direct read-out is obtained by mapping the optical spectrum onto the radio-frequency spectrum output of the dual-comb. This interrogation scheme is proposed for measuring fast phenomena such as vibrations and ultrasounds. Results are presented for dual-comb operation under optimized control. The optical modes are mapped onto detectable tones that are multiples of 0.5 MHz around a center radiofrequency tone (40 MHz. Measurements of ultrasounds (40 kHz and 120 kHz are demonstrated with this sensing system. Ultrasounds induce dynamic strain onto the fiber, which generates changes in the reflected Bragg wavelength and, hence, modulates the amplitude of the OFC modes within the reflected spectrum. The amplitude modulation of two counterphase tones is detected to obtain a differential measurement proportional to the ultrasound signal.

  3. Determination of the complex linear electro-optic coefficient of GaAs and InP

    Energy Technology Data Exchange (ETDEWEB)

    Pristovsek, Markus [Technische Universitaet Berlin, Institut fuer Festkoerperphysik, Hardenbergstrasse 36, 10623 Berlin (Germany)

    2010-08-15

    The complex linear electro-optic coefficient d{sub 41} was determined for the first time above the fundamental band gap of GaAs and InP by measuring the doping induced band bending of several oxidized samples in reflectance anisotropy spectroscopy. From the real and imaginary part of the change of the spectra for different carrier concentrations the spectral change of d{sub 41} was calculated. This is the first determination of the imaginary part Im(d{sub 41}). (Abstract Copyright [2010], Wiley Periodicals, Inc.)

  4. Low voltage integrated optics electro-optical modulator applied to optical voltage transformer based on WLI technique

    Science.gov (United States)

    Santos, J. C.; Rubini, J.; Silva, L. P. C.; Caetano, R. E.

    2015-09-01

    The use of two electro-optical modulators linked in series, one for sensing and one for recovering signals, was formerly presented by some of the authors as a solution for interrogation of optical fiber sensor systems based on WLI method. A key feature required from such systems is that half-wave voltage (Vπ) of recovering modulator must be as small as possible. Aiming at meeting this requirement, in this paper it is presented the use of an unbalanced Michelson Interferometer implemented using an integrated optics component as recover interferometer in an optical voltage transformer intended for high voltage measurements.

  5. Electro-optical determination of the constant electric dipole of disperse particles by the method of crossed electric fields

    Energy Technology Data Exchange (ETDEWEB)

    Voitylov, V.V.; Spartakov, A.A.; Tolstoi, N.A.; Trusov, A.A.; Boitsova, I.N. [St. Petersburg State Univ. (Russian Federation)

    1995-04-01

    An electro-optical method of crossed electric fields is proposed for determining constant dipole colloidal particles moments of colloidal particles. Fields of this type make it possible to study the motion of colloidal particles determined exclusively by their constant moments, which substantially improves the measurement accuracy of these moments. This is of particular importance for the investigation of colloidal particles with constant dipole moments less than or comparable to induced dipole moments. For a number of disperse systems, the constant dipole moments per unit area of particles are determined. It is shown that the values of these specific moments are close to each other.

  6. Compact silicon-on-insulator-based 2 × 2 Mach-Zehnder interferometer electro-optic switch with low crosstalk

    Institute of Scientific and Technical Information of China (English)

    Jiejiang Xing; Zhiyong Li; Peiji Zhou; Yuanhao Gong; Yude Yu; Manqing Tan; Jinzhong Yu

    2015-01-01

    We report a compact 2 × 2 Mach-Zehnder interferometer (MZI) electro-optic switch fabricated on a siliconon-insulator using standard complementary metal-oxide semiconductor (CMOS) processes.With a short modulation arm length of 200 μm,the crosstalk is reduced to-22 dB by the new modulation scheme of push-pull modulation with a pre-biased π/2 phase shift.The new modulation scheme can also work with a fast switching time of about 5.4 ns.

  7. Progress in Nano-Electro-Optics VII Chemical, Biological, and Nanophotonic Technologies for Nano-Optical Devices and Systems

    CERN Document Server

    Ohtsu, Motoichi

    2010-01-01

    This book focuses on chemical and nanophotonic technology to be used to develop novel nano-optical devices and systems. It begins with temperature- and photo-induced phase transition of ferromagnetic materials. Further topics include: energy transfer in artificial photosynthesis, homoepitaxial multiple quantum wells in ZnO, near-field photochemical etching and nanophotonic devices based on a nonadiabatic process and optical near-field energy transfer, respectively and polarization control in the optical near-field for optical information security. Taken as a whole, this overview will be a valuable resource for engineers and scientists working in the field of nano-electro-optics.

  8. Effects of chromophore concentration and film thickness on thermo-optic properties of electro-optic fluorinated polyimide films

    Institute of Scientific and Technical Information of China (English)

    Hongxiang Song; Chengxun Wu

    2007-01-01

    Electro-optic (EO) effect and thermo-optic (TO) effect are jointly considered on the basis of field-induced and temperature-affected perturbations of the operating point in waveguide components. TO coefficients of EO fluorinated polyimide films with side-chain azobenzene chromophore were measured by attenuatedtotal-reflection (ATR) technique at different temperatures with TE- and TM-polarized lights, respectively.It is found that the absolute values of TO coefficients increase with the increments of both chromophore concentration and film thickness, but the polarization dependence of TO coefficients increases with the increment of chromophore concentration and decreases with the increment of film thickness.

  9. Nanosecond Pulse Shaping with Fiber-Based Electro-Optical Modulators and a Double-Pass Tapered Amplifier

    CERN Document Server

    Rogers, Charles E

    2015-01-01

    We describe a system for generating frequency-chirped and amplitude-shaped pulses on time scales from sub-nanosecond to ten nanoseconds. The system starts with cw diode-laser light at 780 nm and utilizes fiber-based electro-optical phase and intensity modulators, driven by an arbitrary waveform generator, to generate the shaped pulses. These pulses are subsequently amplified to several hundred mW with a tapered amplifier in a delayed double-pass configuration. Frequency chirps up to 5 GHz in 2 ns and pulse widths as short as 0.15 ns have been realized.

  10. Processing and Properties of High Performance Lead Free Electro-Optic Ceramics

    Science.gov (United States)

    Dupuy, Alexander Davis

    Electro-optic (EO) materials allow for the precise control of light using electrical signals, which has allowed for the advancement of an incredible array of photonic technologies such as laser systems and optical telecommunications. Most EO devices currently utilize single crystals, but high performance EO single crystals often have composition limitations since dopants can segregate and not all compositions can be grown using equilibrium restricted techniques. Bulk polycrystalline ceramic materials can potentially overcome such limitations and allow for the exploration of new EO systems. Due to the specific microstructures required for transparency, conventional processing techniques have difficulty in producing bulk polycrystalline EO ceramics. Reported here for the first time are the optical and EO properties of a new class of transparent lead free ceramic that outperforms EO materials in use today. This material is a barium titanate (BaTiO3) based solid solution, (1-x)Ba(Zr0.2Ti0.8)O 3-x(Ba0.7Ca0.3)TiO3 referred to here as BXT. The EO material was successfully processed using the Current Activated Pressure Assisted Densification (CAPAD) technique, commonly called Spark Plasma Sintering (SPS), which has been shown to be effective at consolidating optical materials. Using this technique along with a new powder synthesis method, it was possible to produce a transparent EO BXT ceramic with a highly dense and homogeneously reacted microstructure. Densified BXT shows a remarkable EO coefficient of 530 pm/V, which is superior not only to state of the art LiNbO3 crystals but also top-quality lead containing ferroelectric ceramics such as PLZT. This exceptional coefficient will allow for miniaturized EO systems with reduced operating voltages. The mechanisms behind the high EO performance in BXT were determined using additional EO and ferroelectric measurements. These measurements indicate that BXT undergoes a field induced structural evolution which heavily

  11. On-chip microwave-to-optical quantum coherent converter based on a superconducting resonator coupled to an electro-optic microresonator

    Science.gov (United States)

    Javerzac-Galy, C.; Plekhanov, K.; Bernier, N. R.; Toth, L. D.; Feofanov, A. K.; Kippenberg, T. J.

    2016-11-01

    We propose a device architecture capable of direct quantum coherent electro-optical conversion of microwave-to-optical photons. The hybrid system consists of a planar superconducting microwave circuit coupled to an integrated whispering-gallery-mode microresonator made from an electro-optical material. We show that by exploiting the large vacuum electric field of the planar microwave resonator, electro-optical (vacuum) coupling strengths g0 as large as ˜2 π O (10 -100 ) kHz are achievable with currently available technology—a more than 3 orders of magnitude improvement over prior designs and realizations. Operating at millikelvin temperatures, such a converter would enable high-efficiency conversion of microwave-to-optical photons. We analyze the added noise and show that maximum quantum coherent conversion efficiency is achieved for a multiphoton cooperativity of unity which can be reached with optical power as low as O (1 ) mW.

  12. On-chip microwave-to-optical quantum coherent converter based on a superconducting resonator coupled to an electro-optic microresonator

    CERN Document Server

    Javerzac-Galy, Clément; Bernier, Nathan; Toth, Laszlo D; Feofanov, Alexey K; Kippenberg, Tobias J

    2015-01-01

    We propose a device architecture capable of direct quantum electro-optical conversion of microwave to optical photons. The hybrid system consists of a planar superconducting microwave circuit coupled to an integrated whispering-gallery-mode microresonator made from an electro-optical material. We show that electro-optical (vacuum) coupling rates $g_0$ as large as$\\sim 2\\pi \\, \\mathcal{O}(10-100)$ kHz are achievable with currently available technology, due to the small mode volume of the planar microwave resonator. Operating at millikelvin temperatures, such a converter would enable high-efficiency conversion of microwave to optical photons. We analyze the added noise, and show that maximum conversion efficiency is achieved for a multi-photon cooperativity of unity which can be reached with optical power as low as $ \\mathcal{O}(1)\\,\\mathrm{mW} $.

  13. Design of Optical Tunable CNOT (XOR) and XNOR Logic Gates Based on 2D-Photonic Crystal Cavity Using Electro-Optic Effect

    CERN Document Server

    Abbasian, Karim; Sadeghi, Parvin

    2016-01-01

    We have proposed optical tunable CNOT (XOR) and XNOR logic gates using two-dimensional photonic crystal (2DPhC) cavities. Where, air rods with square lattice array have been embedded in Ag-Polymer substrate with refractive index of 1.59. In this work, we have enhanced speed of logic gates by applying two input signals with a phase dif?ference at the same wavelength for 2DPhC cavities. Where, we have adjusted the phases of input and control signals equal with {\\pi}/3 and zero, respectively. The response time of the structure and quality factor of the cavities are in the range of femtosecond and 2000, respectively. Then, we have used electro-optic property of the substrate material to change the cavities resonance wavelengths. By this means, we could design the logic gates and demonstrate a tunable range of 23nm for their operation wavelength. The quality factor and the response times of cavities remain constant in the tunable range of wavelength, approximately. The evaluated least ON to OFF logic-level contras...

  14. Manufacture tolerance analysis and control for a polymer on-silicon Mach-Zehnder-interferometer-based electro-optic switch

    Institute of Scientific and Technical Information of China (English)

    ZHENG Chuan-tao; MA Chun-sheng; YAN Xin; CUI Zhan-chen; ZHANG Da-ming

    2011-01-01

    To enhance the electro-optic (EO) modulation efficiency and realize the impedance-matching, a polymer-on-silicon multi mode interference (MMI) Mach-Zehnder interferometer (MZI) -based electro-optic (EO) switch is designed and optimized.Under the central operation wavelength of 1550 nm, the driving voltages of the designed switch are O and ±1.375 V,respectively, with a short active region length of 5 mm, and the characteristic impedance of the electrode is about 49.6 Ω.The manufacture tolerance is analyzed for instructing the device fabrication. The results show that to realize ideal switching function, high fabrication accuracy on the buffer thickness, core thickness, electrode width and MMI wavegnide width is extremely required, and a small voltage drift of-0.03-0.05 V is also expected for reducing the crosstalk to less than -30 dB.The allowed 3 dB bandwidth is 60 nm, and within this spectrum range, the insertion loss and crosstalk are less than 6.71 dB and -30 dB, respectively.

  15. Electro-optic Properties of DR1 Doped SiO_2 Organic/inorganic Guest-host Films

    Institute of Scientific and Technical Information of China (English)

    LIU Shao-lin; YANG Han; JIN Ru-long; YAN Zhao-xu; YI Mao-bin

    2009-01-01

    We made a comprehensive investigation on the electro-optic(EO) properties of hybrid sol-gel silica film doped with Dispersed Red 1 dye(DRl/SiO_2). An important finding is that the dipoles which don't orient along the direction of corona poling field in the films can be instantaneously poled by alternate modulation electrical field. This instant poling effect results in the EO coefficients dependent on the frequency and intensity of alternate modulation electric field, and some experiments have proved it. We also investigated the electro-optic coefficients and thickness of films at different stir temperatures(T_s) of start solution and at different number densities of DR1. Experimentally the DR1 number density was optimized to an order of 10~(21)/cm~3 and a large EO coefficient of γ_(33)= 37 pm/V for DR1/SiO_2 film was measured by simple reflection technique at 1 kHz frequencies of modulation electric field. These findings may benefit the practical application of DR1/SiO_2 films in the field of EO modulator and EO probing.

  16. Electro-optical and dielectric properties of a high tilt antiferroelectric liquid crystal mixture (W-193B)

    Energy Technology Data Exchange (ETDEWEB)

    Nayek, Prasenjit; Ghosh, Sharmistha; Kundu, Sudarshan; Roy, Subir Kr [Department of Spectroscopy, Indian Association for the Cultivation of Science, Jadavpur, Calcutta-700032 (India); Majumder, Tapas Pal [Department of Physics, University of Kalyani, Kalyani-741235, West Bengal (India); Bennis, Noureddine; Oton, Jose Manuel [Department of TecnologIa Fotonica, ETSI Telecomunicacion, Universidad Politecnica de Madrid, Ciudad Universitaria, 28040 Madrid (Spain); Dabrowski, Roman, E-mail: spskr@iacs.res.i [Institute of Chemistry, Military University of Technology, 00-908 Warsaw (Poland)

    2009-11-21

    The electro-optical properties and dielectric relaxation have been investigated for an antiferroelectric liquid crystal mixture W-193B. The material exhibits smectic A*, smectic C* and a wide range of anticlinic smectic C{sub A}{sup *} phases. The high tilt and broad room temperature smectic C{sub A}{sup *} phase make it a good candidate for antiferroelectric display materials. Dielectric studies have been made in a planarly aligned cell in the frequency range 10 Hz-13 MHz. Dielectric spectroscopy reveals the existence of soft mode in the smectic A* phase and Goldstone mode in the smectic C* phase. In the smectic C{sub A}{sup *} phase the dielectric spectrum of the material exhibits two absorption peaks related to the rotational fluctuation around the short axis of the molecules and antiphase azimuthal angle fluctuation, respectively, and are separated by about two orders of frequency. Electro-optical response using a low frequency triangular wave showed a very high quasi-static contrast ratio of 132 : 1, threshold voltage of around 7 V and saturation of 17 V. Surface-stabilized, low thickness cells of this mixture showed a perfect double hysteresis loop with a 1 Hz triangular signal, reaching different transmission levels for different voltage amplitudes. These levels can be stabilized with a single holding voltage, making it possible for the material to be passively multiplexed at video rate.

  17. Effects of carbon nanotubes on liquid crystal order parameter and Freedericksz transition in electro-optic cells

    Science.gov (United States)

    Georgiev, Georgi; Gombos, Erin; McIntyre, Michael; Mattera, Michael; Gati, Peter; Cabrera, Yaniel; Cebe, Peggy

    2010-03-01

    We studied the effects of multiwalled carbon nanotubes (MWCTs) at low concentrations (0.01 wt %) on the Freedericksz transition of a 4-Cyano-4'-pentylbipenyl (5CB) liquid crystal using transmission ellipsometry. In addition, we calibrated the altitudinal angle of CNTs as a function of the electric field and directed the azimuthal angle which gave us complete control of the 3D orientation of the CNTs. Our results show that in the presence of CNTs the voltage and width for the Freedericksz transition are reduced by a factor of 1.8 as compared to the control electro-optic cell without CNTs. The shift in transition voltage correlates with increase in order parameter of the electro-optic cell as measured by our polarized UV/Vis absorption spectroscopy results. Research supported by: Assumption College Faculty Development Grant, funding for students' stipends, instrumentation and supplies, the NSF Polymers Program of the DME, grant (DMR-0602473) and NASA grant (NAG8-1167).

  18. Electro-optic comb based real time ultra-high sensitivity phase noise measurement system for high frequency microwaves.

    Science.gov (United States)

    Kuse, N; Fermann, M E

    2017-06-06

    Recent progress in ultra low phase noise microwave generation indispensably depends on ultra low phase noise characterization systems. However, achieving high sensitivity currently relies on time consuming averaging via cross correlation, which sometimes even underestimates phase noise because of residual correlations. Moreover, extending high sensitivity phase noise measurements to microwaves beyond 10 GHz is very difficult because of the lack of suitable high frequency microwave components. In this work, we introduce a delayed self-heterodyne method in conjunction with sensitivity enhancement via the use of higher order comb modes from an electro-optic comb for ultra-high sensitivity phase noise measurements. The method obviates the need for any high frequency RF components and has a frequency measurement range limited only by the bandwidth (100 GHz) of current electro-optic modulators. The estimated noise floor is as low as -133 dBc/Hz, -155 dBc/Hz, -170 dBc/Hz and -171 dBc/Hz without cross correlation at 1 kHz, 10 kHz, 100 kHz and 1 MHz Fourier offset frequency for a 10 GHz carrier, respectively. Moreover, since no cross correlation is necessary, RF oscillator phase noise can be directly suppressed via feedback up to 100 kHz frequency offset.

  19. Direct electro-optical pumping for hybrid CdSe nanocrystal/III-nitride based nano-light-emitting diodes

    Science.gov (United States)

    Mikulics, M.; Arango, Y. C.; Winden, A.; Adam, R.; Hardtdegen, A.; Grützmacher, D.; Plinski, E.; Gregušová, D.; Novák, J.; Kordoš, P.; Moonshiram, A.; Marso, M.; Sofer, Z.; Lüth, H.; Hardtdegen, H.

    2016-02-01

    We propose a device concept for a hybrid nanocrystal/III-nitride based nano-LED. Our approach is based on the direct electro-optical pumping of nanocrystals (secondary excitation) by electrically driven InGaN/GaN nano-LEDs as the primary excitation source. To this end, a universal hybrid optoelectronic platform was developed for a large range of optically active nano- and mesoscopic structures. The advantage of the approach is that the emission of the nanocrystals can be electrically induced without the need of contacting them. The proof of principal was demonstrated for the electro-optical pumping of CdSe nanocrystals. The nano-LEDs with a diameter of 100 nm exhibit a very low current of ˜8 nA at 5 V bias which is several orders of magnitude smaller than for those conventionally used. The leakage currents in the device layout were typically in the range of 8 pA to 20 pA/cm2 at 5 V bias. The photon-photon down conversion efficiency was determined to be 27%. Microphotoluminescence and microelectroluminescence characterization demonstrate the potential for future optoelectronics and highly secure "green" information technology applications.

  20. Research on Airborne Electro-Optical Tracking and Sighting System Based on Fuzzy PID and H∞ Control

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Airborne electro-optical tracking and sighting system is a three-degree-of-freedom angular position servo system which is influenced by multi-disturbance, and its control system consists of stabilizing and tracking components. Stabilizing control is applied to track angular velocity order and control multi-disturbance under airborne condition, and its robustness should be very good; tracking control is applied to compensate tracking error of angular position. A mathematical model is established by taking the control of yaw loop as example. H∞ stabilizing controller is designed by taking the advantage of H∞ control robustness and combining with Kalman filter. A fuzzy control is introduced in general PID control to design a decoupled fuzzy Smith estimating PID controller for tracking control. Simulation research shows that the control effect of airborne electro-optical tracking and sighting system based on fuzzy PID and H∞ control is good, especially when the model parameters change and the multi-disturbance exists, the system capability has little fall, but this system still can effectively track a target.

  1. High-Contrast Electro-Optic Modulation of a Photonic Crystal Nanocavity by Electrical Gating of Graphene

    CERN Document Server

    Gan, Xuetao; Gao, Yuanda; Mak, Kin Fai; Yao, Xinwen; Li, Luozhou; Szep, Attila; Walker, Dennis; Hone, James; Heinz, Tony F; Englund, Dirk

    2012-01-01

    We demonstrate a high-contrast electro-optic modulation of a photonic crystal nanocavity integrated with an electrically gated monolayer graphene. A high quality (Q) factor air-slot nanocavity design is employed for high overlap between the optical field and graphene sheet. Tuning of graphene's Fermi level up to 0.8 eV enables efficient control of its complex dielectric constant, which allows modulation of the cavity reflection in excess of 10 dB for a swing voltage of only 1.5 V. We also observe a controllable resonance wavelength shift close to 2 nm around a wavelength of 1570 nm and a Q factor modulation in excess of three. These observations allow cavity-enhanced measurements of the graphene complex dielectric constant under different chemical potentials, in agreement with a theoretical model of the graphene dielectric constant under gating. This graphene-based nanocavity modulation demonstrates the feasibility of high-contrast, low-power frequency-selective electro-optic nanocavity modulators in graphene...

  2. A Comparison between Two Heterodyne Light Sources Using Different Electro-Optic Modulators for Optical Temperature Measurements at Visible Wavelengths

    Directory of Open Access Journals (Sweden)

    Ruey-Ching Twu

    2010-10-01

    Full Text Available In this paper we have successfully demonstrated a z-propagating Zn-indiffused lithium niobate electro-optic modulator used for optical heterodyne interferometry. Compared to a commercial buck-type electro-optic modulator, the proposed waveguide-type modulator has a lower driving voltage and smaller phase variation while measuring visible wavelengths of 532 nm and 632.8 nm. We also demonstrate an optical temperature measurement system using a homemade modulator. The results show that the measurement sensitivities are almost the same values of 25 deg/°C for both the homemade and the buck-type modulators for a sensing light with a wavelength of 632.8 nm. Because photorefractive impacts are essential in the buck-type modulator at a wavelength of 532 nm, it is difficult to obtain reliable phase measurements, whereas the stable phase operation of the homemade one allows the measurement sensitivity to be improved up to 30 deg/°C with the best measurement resolution at about 0.07 °C for 532 nm.

  3. Photo-stimulated electro-optic response of liquid-crystalline system with trans-cis photo-isomerizable agent

    Science.gov (United States)

    Hadjichristov, G. B.; Marinov, Y. G.; Yelamaggad, C. V.

    2014-12-01

    A rather strong photo-stimulated enhancement of photo-induced bend flexoelectric effect based on trans-cis photoisomerization of azo bond was found in a guest-host system formed from the nematic liquid crystal (LC) N-(4-methoxybenzylidene)-4-butylaniline (MBBA) as a host, and the azobenzene LC 4-hexyloxybenzoloxy-4'-cyanoazobenzene, as a guest photoactive agent at 1 wt.% concentration. Upon application of electric field, thin homeotropic layers of thickness 100 pm containing this photo-sensitized LC mixture were investigated as subjected to a relatively weak illumination with UV light (λ = 375 nm, from narrow-band light-emitting diode, LED). The stimulation of the photoactive electro-optic response of azobenzene-doped MBBA (owing to enhanced photo-induced bend flexoelectric effect driven by the photo-isomerizable dopants) was achieved by pre-resonant excitation of the photoactive agent. The degree of the effect measured is of potential interest for thin-film photoactive electro-optic applications. The UV light-induced effect in azobenzene-doped MBBA was reversible; the back (relaxation) process was stimulated by light in the blue from a LED with broadband spectrum centered at 455 nm.

  4. Effect of a Polymercaptan Material on the Electro-Optical Properties of Polymer-Dispersed Liquid Crystal Films

    Directory of Open Access Journals (Sweden)

    Yujian Sun

    2016-12-01

    Full Text Available Polymer-dispersed liquid crystal (PDLC films were prepared by the ultraviolet-light-induced polymerization of photopolymerizable monomers in nematic liquid crystal/chiral dopant/thiol-acrylate reaction monomer composites. The effects of the chiral dopant and crosslinking agents on the electro-optical properties of the PDLC films were systematically investigate. While added the chiral dopant S811 into the PDLC films, the initial off-state transmittance of the films was decreased. It was found that the weight ratio among acrylate monomers, thiol monomer PETMP and the polymercaptan Capcure 3-800 showed great influence on the properties of the fabricated PDLC films because of the existence of competition between thiol-acrylate reaction and acrylate monomer polymerization reaction. While adding polymercaptans curing agent Capcure 3-800 with appropriate concentration into the PDLC system, lower driven voltage and higher contrast ratio were achieved. This made the polymer network and electro-optical properties of the PDLC films easily tunable by the introduction of the thiol monomers.

  5. Dependence of electro-optical properties on the deposition conditions of chemical bath deposited CdS thin films

    Energy Technology Data Exchange (ETDEWEB)

    Dona, J.M.; Herrero, J. [CIEMAT, Madrid (Spain). Inst. de Energias Renovables

    1997-11-01

    Lately, there has been a sharp increase in the publication of papers on chemical bath deposition of CdS thin films and related materials due to successful results obtained using this method to fabricate CdS thin-film buffer layers for CuInSe{sub 2}- and CdTe-based polycrystalline thin-film solar cells. Generally, these papers focus on previously proposed methods of studying film characteristics without a systematic study of the influence of deposition conditions on film characteristics. In this paper the authors present an exhaustive study of the chemical bath-deposited CdS thin films electro-optical properties dependence on deposition variables. The authors propose not only a set of conditions for obtaining CdS thin films by this method but additionally, suitable deposition process conditions for certain application requirements, such as buffer layers for thin-film solar cells. The observed electro-optical characteristics dependence on the deposition variables corroborates the chemical mechanism that they proposed previously for this process.

  6. Application of the Jones calculus for a modulated double-refracted light beam propagating in a homogeneous and nondepolarizing electro-optic uniaxial crystal.

    Science.gov (United States)

    Izdebski, Marek; Kucharczyk, Włodzimierz; Raab, Roger E

    2004-01-01

    The Jones matrix calculus is applied to an electro-optic crystal with uniaxial symmetry when the light beam is incident nearly normally on the crystal face. The approach allows one to treat refracted waves and rays that diverge in the crystal and are modulated by an external low-frequency field. The effect of partial interference of overlapping refracted beams is allowed for and calculated for the case of uniform intensity of the beam over its cross section. The method is employed to analyze optical systems containing an imprecisely cut and aligned electro-optic crystal plate.

  7. Preliminary Evaluation of a New Cosmology Curriculum

    Science.gov (United States)

    Coble, Kimberly A.; Martin, Dominique; Hayes, Patrycia; Targett, Tom; Bailey, Janelle M.; Cominsky, Lynn R.

    2015-01-01

    Informed by our research on student understanding of cosmology, The Big Ideas in Cosmology is an immersive set of web-based learning modules that integrates text, figures, and visualizations with short and long interactive tasks and real cosmological data. This enables the transformation of general education astronomy and cosmology classes from primarily lecture and book-based courses to a more engaging format that builds important STEM skills.During the spring 2014 semester, we field-tested a subset of chapters with the general education astronomy and cosmology classes at Sonoma State University in a flipped-classroom format. We administered pre and post content and attitude assessments in the two flipped classes as well as two lecture classes. The majority of cosmology students had taken astronomy before whereas the astronomy students had not.When switching to an active mode of learning (e.g., flipped classroom instead of lecture), many instructors report pushback from students. We saw this effect from students in course evaluations, who reported dissatisfaction with "having to do more work." However, the students in the flipped section in astronomy made greater gains on the multiple choice content assessment than the students in either of the two lecture sections. On the attitude assessment (the CLASS), the cosmology students made a small shift toward more expert-like opinions. Preliminary results from open-ended content surveys indicate that, prior to instruction, students had difficulty answering 'why' or 'how do we know' questions; that post-instruction, students are less likely to respond "I don't know" or to leave an answer blank; and that students using the modules made gains in their content knowledge.Module development was supported by NASA ROSES E/PO Grant #NNXl0AC89G, the Illinois Space Grant Consortium, the Fermi E/PO program, Sonoma State University's Space Science Education and Public Outreach Group, and Great River Technology

  8. Optical and electro-optical characteristics of hot-pressing (Pb1-xLaxTiO3 ferroelectric ceramics

    Directory of Open Access Journals (Sweden)

    Garcia, D.

    2012-12-01

    Full Text Available La-modified PbTiO3-based ceramics (PLT are the subject of many studies in term of piezoelectric and pyroelectric applications, but the processing of PLT to optimize their transparency and electro-optical properties has not been studied in detail. Ferroelectric (Pb1-xLaxTiO3 (PLT ceramics, with 0.18 ≤ x ≤ 0.23, were produced by a solid state reaction and uniaxially hot pressing for 3h at a temperature of 1220 ºC, and a pressure of ~6,0 MPa. High density, translucent reddish color and high dc conductivity were observed for all compositions. Nevertheless appropriate thermal treatments in an O2 atmosphere, after hot pressing, led to ceramics with good properties for dielectric, optical and electro-optical studies. The heat-treated samples revealed a homogeneous microstructure, absence of second phases, increased of the transmittance in the visible and infrared range and reduced dc conductivity. These features allowed the electro-optical coefficient of the (Pb,LaTiO3 system to be calculated.Las cerámicas basadas en PbTiO3 con adición de La, (PLT han sido ampliamente estudiadas debido a sus aplicaciones piro y piezoeléctricas. Por otra parte, el procesamiento de PLT para optimizar su transparencia y sus propiedades electro-ópticas no ha sido estudiado com el mismo detalle. En el presente trabajo, se han preparado cerámicas ferroeléctricas de (Pb1-xLax TiO3 (PLT con 0.18 ≤ x ≤ 0.23, mediante síntesis en estado sólido y prensado uniaxial en caliente por 3 h a una temperatura de 1220 ºC, y una presión de ~6,0 MPa. En todas lãs composiciones se han observado una alta densidad, baja transparencia y conducción eléctrica elevada. Mediante adecuados tratamientos posteriores en atmósfera de O2 se há mejorado la calidad eléctrica y óptica de dichas cerámicas. La microestructura es homogénea, la transmitancia en las regiones visible e infrarroja crece y la conductividad DC disminuye. Estas características han permitido medir el

  9. Investigation of chromophore-chromophore interaction by electro-optic measurements, linear dichroism, x-ray scattering, and density-functional calculations

    DEFF Research Database (Denmark)

    Apitz, Dirk; Bertram, R.P.; Benter, N.;

    2005-01-01

    Free-beam interferometry and angle-resolved absorption spectra are used to investigate the linear electro-optic coefficients and the linear dichroism in photoaddressable bis-azo copolymer thin films. From the first- and second order parameters deduced, the chromophore orientation distribution is ...

  10. Investigating electro-optical properties of a nematic liquid crystal cell with planar anchoring boundary condition for various thicknesses: A Monte Carlo study

    Science.gov (United States)

    Emül, Yakup; Polat, Ömer; San, Sait Eren; Kayacan, Özhan; Özbek, Haluk

    2014-06-01

    Monte Carlo (MC) simulations and the Mueller matrix formalism were applied to investigate electro optical properties of a LC cell with planar boundary conditions for various thicknesses. Field dependent global order parameter and the optical transmissions were analyzed in common. Three characteristic regions of the periodicity of optical transmissions as a function of polarizer angle and the external field were identified.

  11. An investigation of the influence of residual amplitude modulation in phase electro-optic modulator on the signal of fiber-optic gyroscope

    Science.gov (United States)

    Pogorelaya, D. A.; Smolovik, M. A.; Strigalev, V. E.; Aleynik, A. S.; Deyneka, I. G.

    2016-08-01

    The investigation is devoted to residual amplitude modulation (RAM) of phase electro-optic modulator, which guides are made in LiNbO3 crystal by Ti diffusion technology. An analysis is presented that shows influence of RAM on the signal of fiber-optic gyroscope. The RAM compensation method is offered.

  12. 一种光电成像系统调制传递函数的测量方法%Modulation Transfer Function Measurement Method of Electro-Optical Imaging System

    Institute of Scientific and Technical Information of China (English)

    徐保树; 史泽林; 冯斌

    2011-01-01

    Modulation transfer function (MTF) is one of significant parameters for designing and evaluating an electro-optical imaging system. By proving the linear relation between an edge spread function and an inverse cumulative histogram of edge, an MTF measurement method based on statistical histogram is presented. Simulation and experiment including optics and detectors are designed. Physical experimental platform including an integrating sphere, target, collimator, digital camera and other devices is developed. Taking the theoretical model and design parameters of electro-optical imaging system as a reference, the validity of our measurement method is verified by the simulation and experiment. Experimental results indicate that, comparing with the existing MTF measurement method, the proposed method can overcome the phase effects which is caused by under-sampling of imaging detector. It is more robust to angle of knife edge and noisy environment, and can measure response properties beyond the sampling frequency of an electro-optical imaging system.%调制传递函数(MTF)是设计和评价光电成像系统的重要参数,在证明了边缘图像的边缘扩展函数与累积直方图逆函数存在着线性关系的基础上,提出了一种基于统计直方图的MTF测量方法,设计了包括光学系统和探测器的仿真实验,搭建了包括积分球、靶标、平行光管和数字摄像机等装置的物理实验平台,以光电成像系统的设计参数和理论模型得到的理论曲线为参考依据,通过仿真实验和物理实验验证了该方法的有效性.实验结果表明,与传统MTF测量方法相比,该方法克服了成像探测器欠采样引起的相位效应,对刀口倾斜角度变化和噪声具有稳健性,可测量超过采样频率的响应特性.

  13. Ultraviolet imprinting and aligned ink-jet printing for multilayer patterning of electro-optic polymer modulators.

    Science.gov (United States)

    Lin, Xiaohui; Ling, Tao; Subbaraman, Harish; Zhang, Xingyu; Byun, Kwangsub; Guo, L Jay; Chen, Ray T

    2013-05-15

    The present work demonstrates an electro-optic polymer-based Mach-Zehnder (MZ) modulator fabricated utilizing advanced ultraviolet (UV) imprinting and aligned ink-jet printing technologies for patterning and layer deposition. The bottom electrode layer is designed and directly ink-jet printed on the substrate to form the patterned layer. The waveguide structure is formed into a bottom cladding polymer using a transparent flexible mold-based UV imprinting method. All other layers can be ink-jet printed. The top electrode is aligned and printed over the MZ arm. The modulator demonstrates a V-pi of 8 V at 3 kHz. This technology shows great potential in minimizing the fabrication complexity and roll-to-roll compatibility for manufacturing low cost, lightweight, and conformal modulators at high throughput.

  14. Modulation Depth Based on Frequency-shift Characteristic of LiNbO3 Waveguide Electro-optic Intensity Modulator

    Institute of Scientific and Technical Information of China (English)

    Hui-juan ZHOU; Zhou MENG; Yi LIAO

    2010-01-01

    The modulation depth,defined according to practical mod-ulation results,which changes with the microwave power and its fre-quency,is significant for systems utilizing the frequency-shift charac-teristic of the LiNbO3 waveguide Electro-Optic Intensity Modulator (EOIM).By analyzing the impedance mismatch between the micro-wave source and the EOIM,the effective voltage applied to the RF port of the EOIM is deprived frcm the microwave power and its fre-quency.Associating with analyses of the phase velocity mismatch be-tween the microwave and the optical wave,the theoretical modulation depth has been obtained,which is verified by experimental results.We provide a method to choose the appropriate modulation depth to optimize the desired sideband through proper transmission bias far the system based an the frequency-shift characteristic of the EOIM.

  15. High-speed 2×2 silicon-based electro-optic switch with nanosecond switch time

    Institute of Scientific and Technical Information of China (English)

    Xu Xue-Jun; Chen Shao-Wu; Xu Hai-Hua; Sun Yang; Yu Yu-De; Yu Jin-Zhong; Wang Qi-Ming

    2009-01-01

    A 2 × 2 electro-optic switch is experimentally demonstrated using the optical structure of a Mach-Zehnder interferometer (MZI) based on a submicron rib waveguide and the electrical structure of a PIN diode on silicon-on-insulator (SOI). The switch behaviour is achieved through the plasma dispersion effect of silicon. The device has a modulation arm of 1 mm in length and cross-section of 400 nm×340 nm. The measurement results show that the switch has a VπLπ figure of merit of 0.145 V.cm and the extinction ratios of two output ports and cross talk are 40 dB,28 dB and -28 dB,respectively. A 3 dB modulation bandwidth of 90 MHz and a switch time of 6.8 ns for the rise edge and 2.7 ns for the fall edge axe also demonstrated.

  16. Preparation and laser modulation investigation of quadratic electro-optical crystal Cu:KTN with gradient refractivity effect

    Science.gov (United States)

    Wang, Xuping; Liu, Bing; Yang, Yuguo; Zhang, Yuanyuan; Lv, Xianshun; Wei, Lei; Xu, Jianhua; Ma, Ling; Wang, Jiyang

    2017-06-01

    Copper doped KTN crystals with different doping concentrations were grown by the Czochralski method. The XRD patterns show that all of the crystals are in cubic phase at room temperature. The influences of the CuO doping concentrations on dielectric properties of the crystals were measured. Cu: KTN crystals exhibited color changes depending on the doping concentrations. It was found that the inhomogeneous composition property can be used to form gradient refractivity effect in the case of ion doping. The refractive index gradient reaches 33×10-3/mm for the grown Cu: KTNN crystals. Base on the interaction between the quadratic electro-optic effect and the gradient refractivity effect, the deflection and the intensity of a Cu: KTa0.62Nb0.38O3 sample were modulated in different orientations of the crystal. The deflection efficiency and the half-wave voltage of the modulation are 45 mrad/kV and 75 V, respectively.

  17. Tunable integrated optical filter made of a glass ion-exchanged waveguide and an electro-optic composite holographic grating.

    Science.gov (United States)

    d'Alessandro, Antonio; Donisi, Domenico; De Sio, Luciano; Beccherelli, Romeo; Asquini, Rita; Caputo, Roberto; Umeton, Cesare

    2008-06-23

    We report the fabrication and the optical characterization of a hybrid tunable integrated optical filter. It consists of a diffused ion-exchanged channel waveguide on a borosilicate glass substrate with a cover of the same glass to form a gap filled with a holographic grating. The grating morphology, called POLICRYPS (POlymer LIquid CRYstal Polymer Slices), is made of alternating stripes of polymer and liquid crystal acting as overlayer for the underneath waveguide. The filter structure includes aluminum coplanar electrodes to electrically control the grating properties, allowing the tunability of the filter. The electric driving power required to tune the filter obtained was in the range of submilliwatts due to the efficient liquid crystal electro-optic effect.

  18. Enhanced secure strategy for electro-optic chaotic systems with delayed dynamics by using fractional Fourier transformation.

    Science.gov (United States)

    Cheng, Mengfan; Deng, Lei; Li, Hao; Liu, Deming

    2014-03-10

    We propose a scheme whereby a time domain fractional Fourier transform (FRFT) is used to post process the optical chaotic carrier generated by an electro-optic oscillator. The time delay signature of the delay dynamics is successfully masked by the FRFT when some conditions are satisfied. Meanwhile the dimension space of the physical parameters is increased. Pseudo random binary sequence (PRBS) with low bit rate (hundreds of Mbps) is introduced to control the parameters of the FRFT. The chaotic optical carrier, FRFT parameters and the PRBS are covered by each other so that the eavesdropper has to search the whole key space to crack the system. The scheme allows enhancing the security of communication systems based on delay dynamics without modifying the chaotic source. In this way, the design of chaos based communication systems can be implemented in a modular manner.

  19. A Theoretical and Experimental Research on Terahertz Electro-Optic Sampling at Near-Zero Optical Transmission Point

    Institute of Scientific and Technical Information of China (English)

    XU Shi-Xiang; CAI Hua

    2008-01-01

    We report an improved theoretical model to characterize terahertz electro-optic(EO)sampling detection operating at near crossed-polarizer design by considering the nonzero minimal transmission of polarizers and the polarization purlty of laser beam.The proof-of-concept experiments show that the model can give quiet reasonable explanations on many experimental phenomena in THz EO detection,e.g.the modulation depth vs the different optical biases,the noise level from the balance detector vs the input probe beam power,the main origin of the background light and the incomplete cancellation of noise from the laser intensity fluctuation in balanced detection.The terahertz signals and the noises are also measured based on two different EO sampling schemes for comparison.The measured results support our model very well.

  20. Statistical Real-time Model for Performance Prediction of Ship Detection from Microsatellite Electro-Optical Imagers

    Directory of Open Access Journals (Sweden)

    Lapierre FabianD

    2010-01-01

    Full Text Available Abstract For locating maritime vessels longer than 45 meters, such vessels are required to set up an Automatic Identification System (AIS used by vessel traffic services. However, when a boat is shutting down its AIS, there are no means to detect it in open sea. In this paper, we use Electro-Optical (EO imagers for noncooperative vessel detection when the AIS is not operational. As compared to radar sensors, EO sensors have lower cost, lower payload, and better computational processing load. EO sensors are mounted on LEO microsatellites. We propose a real-time statistical methodology to estimate sensor Receiver Operating Characteristic (ROC curves. It does not require the computation of the entire image received at the sensor. We then illustrate the use of this methodology to design a simple simulator that can help sensor manufacturers in optimizing the design of EO sensors for maritime applications.

  1. Comparison of laser performance of electro-optic Q-switched Nd:YAG ceramic/single crystal laser

    Institute of Scientific and Technical Information of China (English)

    Jianghua Ji; Xiaolei Zhu; Chunyu Wang; Yongwei Feng; Qihong Lou

    2006-01-01

    @@ An electro-optic Q-switched Nd:YAG ceramic laser operating at kHz repetition rate was demonstrated.Thermal induced lens' focus of ceramic rod was measured and compensated by plano-convex cavity structure. Depolarization loss at different output powers was measured in Nd:YAG single crystal and ceramic lasers. High-energy high-beam-quality laser pulse output was obtained in both laser structures. Pulse energy of about 20 mJ and pulse width of less than 12 ns were achieved, and the average power reached 20 W. The divergence of output laser beam was less than 1.2 mrad, and the beam propagation factor M2was about 1.4.

  2. Stable kilo-hertz electro-optically Q-switched Tm,Ho:YAP laser at room temperature

    Science.gov (United States)

    Liu, C.; Zhao, S.; Li, Y.; Yang, K.; Li, M.; Li, G.; Li, D.; Li, T.; Qiao, W.; Feng, T.; Chen, X.; Zheng, L.; Su, L.; Xu, J.

    2016-07-01

    A diode-pumped Tm,Ho:YAP laser utilizing a self-made LiNbO3 (LN) electro-optically modulator (EOM) at room temperature is demonstrated for the first time. A minimum pulse duration of 107.4 ns was obtained at a pulse repetition rate (PRR) of 200 Hz, giving a maximum single pulse energy of 1.65 mJ. At a PRR of 1 kHz, pulse duration of 145.8 ns was achieved under the absorbed pump power of 7.4 W, corresponding to a maximum single pulse energy of 0.546 mJ, and the pulse to pulse amplitude instabilities were measured to be about 4.6% and 5.83% for PRRs of 200 Hz and 1 kHz, respectively.

  3. 20-kHz watt-level green laser with LGS crystal electro-optic Q-switch

    Institute of Scientific and Technical Information of China (English)

    Hao Tang; Xiaolei Zhu; Junqing Meng; Huaguo Zang

    2009-01-01

    A diode-end-pumped electro-optic(EO)Q-switched green laser operating at the repetition rate of 20 kHz is reported.A block of La3Ga5SiO14(LGS)single crystal is used as a Q-switch and the type I phasematching LiB3O5(LBO)is used as the nonlinear crystal in the second harmonic generation.The 2.3-W average power of 532-nm green laser is obtained at the repetition rate of 20 kHz with the pulse width as short as 10 ns.When the output power is about 1.5 W,the measured power fluctuation is less than 1.4% (root-mean-square,RMS)with the beam quality factor of M2 < 2 in both orthogonal directions.

  4. Broadband millimeter-wave electro-optic modulator using multi-patch antennas for pico-cell radar networks

    Science.gov (United States)

    Wijayanto, Yusuf Nur; Kanno, Atsushi; Kawanishi, Tetsuya

    2015-01-01

    An electro-optic (EO) modulator using multi patch antennas is proposed for broadband millimeter-wave bands in pico-cell radar networks. The proposed device is composed of multi patch antennas with a gap fabricated on a LiNbO3 crystal bonded with a low-k dielectric material. Multiple millimeter-wave operational frequencies can be received by the multi patch antennas and converting directly to lightwave signals through the Pockel effects of the LiNbO3 crystal. By adjusting the metal patch size for receiving with relatively close millimeter-wave frequencies, the bandwidth of the EO modulator can be enlarged. Based on that, bandwidth of over 30% in millimeter-wave bands can be achieved using the proposed device.

  5. Cascade photonic integrated circuit architecture for electro-optic in-phase quadrature/single sideband modulation or frequency conversion.

    Science.gov (United States)

    Hasan, Mehedi; Hall, Trevor

    2015-11-01

    A photonic integrated circuit architecture for implementing frequency upconversion is proposed. The circuit consists of a 1×2 splitter and 2×1 combiner interconnected by two stages of differentially driven phase modulators having 2×2 multimode interference coupler between the stages. A transfer matrix approach is used to model the operation of the architecture. The predictions of the model are validated by simulations performed using an industry standard software tool. The intrinsic conversion efficiency of the proposed design is improved by 6 dB over the alternative functionally equivalent circuit based on dual parallel Mach-Zehnder modulators known in the prior art. A two-tone analysis is presented to study the linearity of the proposed circuit, and a comparison is provided over the alternative. The proposed circuit is suitable for integration in any platform that offers linear electro-optic phase modulation such as LiNbO(3), silicon, III-V, or hybrid technology.

  6. Electro-optic properties of nematic and ferroelectric liquid crystalline nanocolloids doped with partially reduced graphene oxide

    Science.gov (United States)

    Lapanik, Valeri; Timofeev, Sergei; Haase, Wolfgang

    2016-02-01

    Flakes of partially reduced graphene oxide (PRGO) were doped in nematic liquid crystals (NLCs) and ferroelectric liquid crystals (FLCs), respectively. The dielectric and electro-optical properties of NLCs doped with those flakes have been investigated. Threshold voltage and switching times are reduced by 30%-50%. This is primarily due to the decrease of the elastic properties of the nanocolloids compared to the non-doped nematics. The influence of the PRGO flakes on the spontaneous polarization, tilt angle and switching time of FLCs was investigated too. Such flakes reduce the response time by 40%-60%, increases spontaneous polarization by 20%-25% and increase the tilt angle by 15%-20%.

  7. Intrinsic reduction the depolarization loss in electro-optical Q-switched laser using a rectangular KD*P crystal

    Science.gov (United States)

    Yin, Xingliang; Jiang, Menghua; Sun, Zhe; Hui, Yongling; Lei, Hong; Li, Qiang

    2017-09-01

    We presented the first demonstration of a new structure KD*P crystal as electro-optic switch, in which the thermal depolarization loss was intrinsically reduced. The thermally induced birefringence and depolarization of both cylindrical and rectangular crystalline structure were simulated. The higher pulse energy or average power output was achieved in the diode pumped E-O Q-switched laser using a rectangular KD*P crystal. At the repetition rate of 100 Hz, the maximum average output power was 27.2 W at 145 A pump current, corresponding to the pulse energy was 272 mJ with pulse width of 65 ns and the beam quality of M2=20.4. Comparing the highest average power or corresponding single pulse energy, the laser with the rectangular KD*P crystal was two times of the laser with the traditional cylindrical KD*P crystal.

  8. Intense transient electric field sensor based on the electro-optic effect of LiNbO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Qing, E-mail: yangqing@cqu.edu.cn; Sun, Shangpeng; Han, Rui; Sima, Wenxia; Liu, Tong [State Key Laboratory of Power Transmission Equipment & System Security and New Technology, Chongqing University, Shapingba District, Chongqing, 400044 (China)

    2015-10-15

    Intense transient electric field measurements are widely applied in various research areas. An optical intense E-field sensor for time-domain measurements, based on the electro-optic effect of lithium niobate, has been studied in detail. Principles and key issues in the design of the sensor are presented. The sensor is insulated, small in size (65 mm × 15 mm × 15 mm), and suitable for high-intensity (<801 kV/m) electric field measurements over a wide frequency band (10 Hz–10 MHz). The input/output characteristics of the sensor were obtained and the sensor calibrated. Finally, an application using this sensor in testing laboratory lightning impulses and in measuring transient electric fields during switch-on of a disconnector confirmed that the sensor is expected to find widespread use in transient intense electric field measurement applications.

  9. Integrating undergraduate research into the electro-optics and laser engineering technology program at Indiana University of Pennsylvania

    Science.gov (United States)

    Zhou, Andrew F.

    2014-07-01

    Bringing research into an undergraduate curriculum is a proven and powerful practice with many educational benefits to students and the professional rewards to faculty mentors. In recent years, undergraduate research has gained national prominence as an effective problem-based learning strategy. Developing and sustaining a vibrant undergraduate research program of high quality and productivity is an outstanding example of the problem-based learning. To foster student understanding of the content learned in the classroom and nurture enduring problem-solving and critical-thinking abilities, we have created a collaborative learning environment by building research into the Electro-Optics curriculum for the first- and second-year students. The teaching methodology is described and examples of the research projects are given. Such a research-integrated curriculum effectively enhances student learning and critical thinking skills, and strengthens the research culture for the first- and second-year students.

  10. Progress in nano-electro optics characterization of nano-optical materials and optical near-field interactions

    CERN Document Server

    Ohtsu, Motoichi

    2005-01-01

    This volume focuses on the characterization of nano-optical materials and optical-near field interactions. It begins with the techniques for characterizing the magneto-optical Kerr effect and continues with methods to determine structural and optical properties in high-quality quantum wires with high spatial uniformity. Further topics include: near-field luminescence mapping in InGaN/GaN single quantum well structures in order to interpret the recombination mechanism in InGaN-based nano-structures; and theoretical treatment of the optical near field and optical near-field interactions, providing the basis for investigating the signal transport and associated dissipation in nano-optical devices. Taken as a whole, this overview will be a valuable resource for engineers and scientists working in the field of nano-electro-optics.

  11. Dielectric and electro-optical properties of polymer-stabilized liquid crystal. II. Polymer PiBMA dispersed in MBBA

    Science.gov (United States)

    Tripathi, Pankaj Kumar; Pande, Mukti; Singh, Shri

    2016-09-01

    In continuation of our earlier work (Pande et al. in Appl Phys A 122:217-226, 2016), we report the results of dielectric and electro-optical properties of pure MBBA and PSLC (polymer PiBMA dispersed in MBBA) systems. The polymer networks domains formed are found to be anisotropic and are oriented in the direction of electric field for both the planar and homeotropic alignment cells. The dielectric anisotropy, optical anisotropy, response time, threshold voltage, splay elastic constant and rotational viscosity were observed for both the LC and PSLC systems with electric field. The liquid crystal properties are affected significantly with increasing concentration of polymer in pure LC material. It has been observed that the polymer networks interaction plays a major role in changing the properties of PSLC system. The effect of dielectric loss and dielectric permittivity on both pure LC and PSLC systems is also discussed.

  12. Electro-optically generating and controlling right- and left-handed circularly polarized multiring modes of light beams.

    Science.gov (United States)

    Zhu, Wenguo; She, Weilong

    2012-07-15

    We propose a simple method for generating and controlling right- and left-handed circularly polarized (RHP and LHP) multiring modes of light beams by means of Pockels effect in a single strontium barium niobate (SBN) crystal. The numerical results show that an LHP Laguerre-Gaussian LG(0l) beam, propagating along the optical axis of the crystal, will partly turn into an RHP vortex light field of order l+2. Moreover, a pair of the LHP and RHP components of the output light field is LG-like modes sharing an identically radial index, which is electro-optically controllable. The power ratio between these two components depends on the applied electric field and the mode of input beam.

  13. INNOVATIONS IN THE SYNTHESIS AND CHARACTERIZATION OF ELECTRO-OPTICAL MATERIALS BASED ON POLYMERS WITH CARBAZOLIC SEQUENCES

    Directory of Open Access Journals (Sweden)

    Ionica Ionita

    2011-05-01

    Full Text Available We live in a complex world where revolutionary progress has been and continues to be made in communications, computer memory, and data processing. There is a growing need for new technologies that rapidly detect and treat diseases at an early stage or even pre-stage. As we are accustomed to these advances, our expectations will demand more compact, energy-efficient, rapidly responding, and environmentally safe technologies. Since the discovery of the photorefractive effect in organic polymers, carbazole-containing polymers have also attracted much attention because of their photoconductivity. In this context, multicomponent polymers with structural units containing both photoconductive and electro-optic functionalities in the side chain can be regarded as potentially suitable materials for photorefractive applications. Azobenzene photochemistry is a fascinating area of investigation, on one hand, because it is fairly well known, and on the other hand, because it has produced and continues to reveal completely unexpected phenomena, some of them still unexplained. When the azobenzene group is incorporated into a polymer, its photoisomerization can have a wide range of unexpected possible consequences. Connecting the carbazole sequence with azo sequence, using en spacer with  electrons, can enhance the electro-optical properties of the polymer materials based on carbazole. That can be realized first by (copolymerization of the monomers with the azo-carbazole sequences. Secondly, the chemical transformations of the polymers contented by (copolymerization of the known monomers with the carbazole monomers will be used. In these ideas the goal of this paper is an investigation of the scientifically literature regarding the new electro-active materials, peculiarly photorefractive alongside of our results in this field.

  14. Electro-optic and magneto-dielectric properties of multifunctional nitride and oxide materials

    Science.gov (United States)

    Dixit, Ambesh

    Materials that simultaneously exhibit different physical properties provide a rich area of research leading to the development of new devices. For example, materials having a strong coupling between charge and spin degrees of freedom are essential to realizing a new class of devices referred to generally as spintronics. However, these multifunctional systems pose new scientific challenges in understanding the origin and mechanisms for cross-control of different functionalities. The core of this Ph.D. dissertation deals with multifunctional nitride and oxide compound semiconductors as well as multiferroic magnetic oxide systems by investigating structural, optical, electrical, magnetic, magnetodielectric and magnetoelectric properties. Thin films of InN nitride compound semiconductors and closely related alloys have been investigated to understand the effects of intrinsic defects on the materials properties while considering possible applications of highly degenerate InN thin films. As grown rf sputtered InN films on c-axis (0001) sapphire exhibit highly degenerate n-type behaviour due to oxygen defects introduced during growth. The effect of oxygen in InN matrix has been further investigated by intentionally adding oxygen into the films. These studies confirm that oxygen is one of the main sources of donor electrons in degenerate InN. Above some critical concentration of oxygen, secondary phases of In 2O3 and In-O-N complexes were formed. It was also possible to tune the carrier concentration to produce changes in the plasmon frequency, which varied from 0.45 eV to 0.8 eV. This characteristic energy scale suggests that these highly degenerate InN thin films could be used for thermophotovoltaic cells, optical filters, and other IR electro-optic applications. To probe the magnetism in transition metal doped InN system, In 0.98Cr0.02N and In0.95Cr0.05N thin films were fabricated. Our results suggest that these films develop ferromagnetic order above room temperature

  15. Effects of CdCl{sub 2} treatment on the recrystallization and electro-optical properties of CdTe thin films

    Energy Technology Data Exchange (ETDEWEB)

    Moutinho, H.R.; Al-Jassim, M.M.; Levi, D.H.; Dippo, P.C.; Kazmerski, L.L. [National Renewable Energy Laboratory, Golden, Colorado 80401 (United States)

    1998-05-01

    The effects of CdCl{sub 2} processing on the physical and electro-optical properties of CdTe were evaluated for thin films produced by physical vapor deposition and close-spaced sublimation (CSS). Two substrates (CdS and Indium{endash}tin{endash}oxide) were used with the physical vapor deposition (PVD) films specifically to isolate the effects of the Cd(S{sub x}Te{sub 1{minus}x}) alloy formed during the treatment of films deposited on CdS. The samples were analyzed by x-ray diffraction (XRD), atomic force microscopy (AFM), and photoluminescence. The observed changes in microstructure were caused by recrystallization, which consisted of the nucleation and development of a new CdTe structure and subsequent grain growth. Nevertheless, for these processes to take place, it was necessary that enough lattice-strain energy was available in the films. For this reason, PVD films did recrystallize, while CSS films did not. For the first time, recrystallization was observed directly in AFM images of CdTe films and confirmed by XRD analysis, which indicated the existence of two lattice parameters in PVD samples treated at 350{degree}C. For samples treated at 400{degree}C, the CdCl{sub 2} treatment improved the minority-carrier lifetime of the films by more than one order of magnitude. This improvement was attributed to the elimination of deep defect levels within the band gap of the CdTe films as a result of the treatment. The sulfur diffusion into CdTe films deposited on CdS, during the CdCl{sub 2} treatment at 400{degree}C, strongly affected the defect structure.

  16. Preliminary analysis of alternative fuel cycles for proliferation evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Steindler, M. J.; Ripfel, H. C.F.; Rainey, R. H.

    1977-01-01

    The ERDA Division of Nuclear Research and Applications proposed 67 nuclear fuel cycles for assessment as to their nonproliferation potential. The object of the assessment was to determine which fuel cycles pose inherently low risk for nuclear weapon proliferation while retaining the major benefits of nuclear energy. This report is a preliminary analysis of these fuel cycles to develop the fuel-recycle data that will complement reactor data, environmental data, and political considerations, which must be included in the overall evaluation. This report presents the preliminary evaluations from ANL, HEDL, ORNL, and SRL and is the basis for a continuing in-depth study. (DLC)

  17. Controlling the Goos-Hänchen shift with external electric and magnetic fields in an electro-optic/magneto-electric heterostructure

    Science.gov (United States)

    Dadoenkova, Yu. S.; Bentivegna, F. F. L.; Dadoenkova, N. N.; Petrov, R. V.; Lyubchanskii, I. L.; Bichurin, M. I.

    2016-05-01

    We present a theoretical investigation of the Goos-Hänchen effect upon light reflection from a heterostructure consisting of an electro-optic film deposited on a magneto-electric film grown on a nonmagnetic dielectric substrate. It is shown that the linear magneto-electric interaction leads to an increase of the lateral shift even in the absence of any applied electric field. The presence of the electro-optic layer enables the control of the Goos-Hänchen shift and of the position of its maximum (with respect to the angle of incidence) through a variation of the magnitude and orientation of an applied electric field. It is also demonstrated that applying an external magnetic field in order to reverse the magnetization in the magnetic layer results (under the influence of the magneto-electric interaction in the system) in a sign reversal of the lateral shift but a nonreciprocal change of its amplitude.

  18. Preliminary Aspects of Language Course Evaluation

    Science.gov (United States)

    Zohrabi, Mohammad

    2012-01-01

    Program and/or course evaluation is a process in which different types of data are collected systematically in order to study the virtues and weaknesses of a language instruction program. Program evaluation is, in fact, one of the essential aspects of any curriculum. It is a kind of quality control in which various aspects of an instructional…

  19. Differences in Metabolite-mediated Toxicity of Tamoxifen in Rodents vs. Humans Elucidated with DNA/microsomes Electro-optical Arrays and Nanoreactors

    OpenAIRE

    2009-01-01

    Tamoxifen, a therapeutic and chemopreventive breast cancer drug, was chosen as a model compound because of acknowledged species specific toxicity differences. Emerging approaches utilizing electro-optical arrays and nanoreactors based on DNA/microsomes films were used to compare metabolite-mediated toxicity differences of tamoxifen in rodents vs. humans. “Hits” triggered by liver enzyme metabolism were first provided by arrays utilizing a DNA damage endpoint. The arrays feature thin-film spot...

  20. Electro-Optical Sensor Fabricated Using a Bulk Cleavage Technique and Its Characteristics for Near-Field Intra-Body Communication

    Science.gov (United States)

    Furuya, Akinori; Sasaki, Ai-ichiro; Morimura, Hiroki; Aihara, Kimihisa; Shinagawa, Mitsuru

    2013-09-01

    This paper describes how to obtain a low cost electro-optical (EO) sensor module for the mass production of near-field intra-body communication devices. In this study, we used a bulk cleavage technique to fabricate EO modulators without the need for any optical polishing or washing processes, and clarified the feasibility of assembling optical components using only a passive alignment technique with a compact housing.

  1. 32 × 32 silicon electro-optic switch with built-in monitors and balanced-status units

    Science.gov (United States)

    Qiao, Lei; Tang, Weijie; Chu, Tao

    2017-02-01

    To construct large-scale silicon electro-optical switches for optical interconnections, we developed a method using a limited number of power monitors inserted at certain positions to detect and determine the optimum operating points of all switch units to eliminate non-uniform effects arising from fabrication errors. We also introduced an optical phase bias to one phase-shifter arm of a Mach–Zehnder interferometer (MZI)-type switch unit to balance the two operation statuses of a silicon electro-optical switch during push–pull operation. With these methods, a 32 × 32 MZI-based silicon electro-optical switch was successfully fabricated with 180-nm complementary metal–oxide–semiconductor (CMOS) process technology, which is the largest scale silicon electro-optical switch to the best of our knowledge. At a wavelength of 1520 nm, the on-chip insertion losses were 12.9 to 16.5 dB, and the crosstalk ranged from ‑17.9 to ‑24.8 dB when all units were set to the ‘Cross’ status. The losses were 14.4 to 18.5 dB, and the crosstalk ranged from ‑15.1 to ‑19.0 dB when all units were in the ‘Bar’ status. The total power consumptions of the 32 × 32 switch were 247.4 and 542.3 mW when all units were set to the ‘Cross’ and ‘Bar’ statuses, respectively.

  2. Short pulse diode-pumped Tm:YAG slab laser electro-optically Q-switched by RbTiOPO4 crystal

    Science.gov (United States)

    Jin, Lin; Liu, Pian; Huang, Haitao; Liu, Xuan; Shen, Deyuan

    2016-10-01

    In this paper, a laser diode end pumped RbTiOPO4 (RTP) electro-optically Q-switched Tm:YAG slab laser was demonstrated. Stable Q-switched pulse with the shortest pulse width of 58 ns and an average output power of 7.5 W were realized at the repetition rate of 1 KHz, corresponding to the slope efficiency of 21.7%.

  3. First single-shot and non-intercepting longitudinal bunch diagnostics for comb-like beam by means of Electro-Optic Sampling

    CERN Document Server

    Pompili, R

    2014-01-01

    At SPARC-LAB, we have installed an Electro-Optic Sampling (EOS) experiment for single shot, non-destructive measurements of the longitudinal distribution charge of individual electron bunches. The profile of the electron bunch field is electro-optically encoded into a Ti:Sa laser, having 130 fs (rms) pulse length, directly derived from the photocathode's laser. The bunch profile information is spatially retrieved, i.e., the laser crosses with an angle of 30° with respect to the normal to the surface of EO crystal (ZnTe, GaP) and the bunch longitudinal profile is mapped into the laser's transverse profile. In particular, we used the EOS for a single-shot direct visualization of the time profile of a comb-like electron beam, consisting of two bunches, about 100 fs (rms) long, sub-picosecond spaced with a total charge of 160 pC. The electro-optic measurements (done with both ZnTe and GaP crystals) have been validated with both RF Deflector (RFD) and Michelson interferometer measurements.

  4. Electro-Optic Property Research of Blue Phase Liquid Crystals%蓝相液晶光电特性研究

    Institute of Scientific and Technical Information of China (English)

    倪水彬; 朱吉亮; 钟恩伟; 陆建钢

    2012-01-01

    蓝相液晶由于其特有的扭曲双螺旋结构,具有快速响应特性与宏观上的光学各向同性.通过聚合物稳定的方法,可以提升其热稳定性,但是也导致了驱动性能下降,磁滞效应增强等问题.文章通过研究手性掺杂和聚合物网络对蓝相液晶材料体系的作用以及不同温度下的磁滞效应,探索蓝相液晶器件光电特性的影响因子,为改善蓝相液晶材料的光电特性提供理论上的支持.%Blue phase liquid crystals (BPLCs) show fast response time and macroscopic optical isotropy due to their double twist cylinder structure. With polymer stabilization, the thermal stability of BPLCs can be improved dramatically. However, it induces some problems to the electro-optic properties of BPLCs material such as high driving voltage, hysteresis and so on. In this paper, different concentrations of chiral dopant, polymer network of the BPLC, and temperature effect are investigated to improve the electro-optic properties of BPLCs and analyze the mechanism that affect the electro-optic properties of the BPLCs device.

  5. 基于PSpice的光电探测电路仿真分析%Simulation and Analysis of Electro-optical Detection Circuit Based on PSpice

    Institute of Scientific and Technical Information of China (English)

    张正茂; 胡心

    2012-01-01

      The performance of electro-optical detection system is affected by the design of electro-optical circuit. The performance of electro-optical detection circuit is simulated based on PSpice EDA software. The PSpice model of photodiode, the characteristics of time domain, frequency domain and noise are analyzed. Ac⁃cording to the parameter scanning function of PSpice software, the circuit parameters are optimized. Based on the noise analysis function of PSpice software, NEP and post-stage circuit design parameters of the system are calculated.%  光电探测电路的设计对光电探测系统的性能有重要的影响。采用PSpice电子电路设计软件,对光电探测电路性能进行了仿真。分析了光电二极管的PSpice模型,光电探测电路的时域特性、频域特性及噪声特性。通过PSpice软件的参数扫描功能,对电路参数进行了优化设计。利用PSpice软件的噪声分析功能,计算了系统等效噪声功率,并对后级电路设计参数进行了计算。

  6. First single-shot and non-intercepting longitudinal bunch diagnostics for comb-like beam by means of Electro-Optic Sampling

    Energy Technology Data Exchange (ETDEWEB)

    Pompili, R., E-mail: riccardo.pompili@lnf.infn.it [INFN-LNF, Via E. Fermi 40, 00044 Frascati, Rome (Italy); Università di Roma “Tor Vergata”, Physics Department, Via della Ricerca Scientifica 1, 00133 Rome (Italy); Cianchi, A. [Università di Roma “Tor Vergata”, Physics Department, Via della Ricerca Scientifica 1, 00133 Rome (Italy); Alesini, D.; Anania, M.P. [INFN-LNF, Via E. Fermi 40, 00044 Frascati, Rome (Italy); Bacci, A. [INFN-Milano, Via Celoria 16, 20133 Milan (Italy); Bellaveglia, M.; Castellano, M.; Chiadroni, E.; Di Giovenale, D.; Di Pirro, G.; Gatti, G. [INFN-LNF, Via E. Fermi 40, 00044 Frascati, Rome (Italy); Giorgianni, F. [Università di Roma “Sapienza”, Physics Department, Via Aldo Moro 2, 00185 Rome (Italy); Ferrario, M. [INFN-LNF, Via E. Fermi 40, 00044 Frascati, Rome (Italy); Lupi, S.; Massimo, F. [Università di Roma “Sapienza”, Physics Department, Via Aldo Moro 2, 00185 Rome (Italy); Mostacci, A. [INFN-LNF, Via E. Fermi 40, 00044 Frascati, Rome (Italy); Rossi, A.R. [INFN-Milano, Via Celoria 16, 20133 Milan (Italy); Vaccarezza, C.; Villa, F. [INFN-LNF, Via E. Fermi 40, 00044 Frascati, Rome (Italy)

    2014-03-11

    At SPARC-LAB, we have installed an Electro-Optic Sampling (EOS) experiment for single shot, non-destructive measurements of the longitudinal distribution charge of individual electron bunches. The profile of the electron bunch field is electro-optically encoded into a Ti:Sa laser, having 130 fs (rms) pulse length, directly derived from the photocathode's laser. The bunch profile information is spatially retrieved, i.e., the laser crosses with an angle of 30° with respect to the normal to the surface of EO crystal (ZnTe, GaP) and the bunch longitudinal profile is mapped into the laser's transverse profile. In particular, we used the EOS for a single-shot direct visualization of the time profile of a comb-like electron beam, consisting of two bunches, about 100 fs (rms) long, sub-picosecond spaced with a total charge of 160 pC. The electro-optic measurements (done with both ZnTe and GaP crystals) have been validated with both RF Deflector (RFD) and Michelson interferometer measurements.

  7. Electro-optic switching in iron oxide nanoparticle embedded paramagnetic chiral liquid crystal via magneto-electric coupling

    Energy Technology Data Exchange (ETDEWEB)

    Goel, Puja, E-mail: pujagoel@gmail.com [Division of Agricultural Chemicals, Indian Agricultural Research Institute, New Delhi 110012 (India); Arora, Manju; Biradar, Ashok M. [Materials Physics and Engineering Division, CSIR-National Physical Laboratory, Dr. K. S. Krishnan Marg, New Delhi 110012 (India)

    2014-03-28

    The variation in optical texture, electro-optic, and dielectric properties of iron oxide nanoparticles (NPs) embedded ferroelectric liquid crystal (FLC) with respect to change in temperature and electrical bias conditions are demonstrated in the current investigations. Improvement in spontaneous polarization and response time in nanocomposites has been attributed to magneto-electric (ME) coupling resulting from the strong interaction among the ferromagnetic nanoparticle's exchange field (due to unpaired e{sup −}) and the field of liquid crystal molecular director. Electron paramagnetic resonance spectrum of FLC material gives a broad resonance signal with superimposed components indicating the presence of a source of spin. This paramagnetic behavior of host FLC material had been a major factor in strengthening the guest host interaction by giving an additional possibility of (a) spin-spin interaction and (b) interactions between magnetic-dipole and electric-dipole moments (ME effects) in the composite materials. Furthermore, the phenomenon of dielectric and static memory effect in these composites are also observed which yet again confirms the coupling of magnetic NP's field with FLC's director orientation. We therefore believe that such advanced soft materials holding the optical and electrical properties of conventional LCs with the magnetic and electronic properties of ferromagnetic nanoparticles are going to play a key role in the development of futuristic multifunctional optical devices.

  8. Study of electro-optic effect in asymmetrically ramped AlInGaAs multiple quantum well structures

    Energy Technology Data Exchange (ETDEWEB)

    Sadiq, Muhammad Usman; Peters, Frank H.; Corbett, Brian [Tyndall National Institute, Lee Maltings, Cork (Ireland); Department of Physics, University College Cork, Cork (Ireland); O' Callaghan, James; Roycroft, Brendan; Thomas, Kevin; Pelucchi, Emanuele [Tyndall National Institute, Lee Maltings, Cork (Ireland)

    2016-04-15

    We investigate the electro-optic properties of two oppositely ramped asymmetric quantum well structures in the AlInGaAs material system. The grading of the bandgap in the quantum wells has been achieved by changing the ratio of Al to Ga in the quaternary alloy during the epitaxial growth. The surface normal photo-response and the Fabry-Perot fringe shift in straight waveguides are compared for both structures as a function of applied voltage at 1550 nm for TE-polarized light. The measurements show a change in the refractive index due to a red shift of the excitonic resonances due to the quantum-confined Stark effect. The 10 quantum well structure with a ramp up of the bandgap in the growth direction leads to the figure of merit of the voltage for a π phase shift, V{sub π} by length, L, V{sub π} x L, of 6 as compared to 7 V . mm in the structure with a ramp in opposite direction. Further investigations show that the reduction in V{sub π} is due to increased absorption at high reverse bias which induces a non-linear phase change. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  9. Linear Electro Optic Effect for High Repetition Rate Carrier Envelope Phase Control of Ultra Short Laser Pulses

    Directory of Open Access Journals (Sweden)

    Michel Comte

    2013-02-01

    Full Text Available This paper is devoted to analyzing the principle and applications of the linear electro-optic (EO effect for the control of the carrier-envelope-phase (CEP. We introduce and detail here an original method, which relies on the use of an EO dispersive prism pair in a compressor-like configuration. We show that, by choosing an adequate geometry, it is possible to shift the CEP without changing the group delay (isochronous carrier-envelope-phase shifter or change the induced group delay without varying the CEP. According to our calculations, when applying an electric field around 400 V/cm to the rubidium titanyle phosphate (RTP prisms in a double pass configuration (2 × 40 mm total length, one obtains a CEP shift of π rad at 800 nm without inducing a group delay. In contrast, this CEP shift is obtained for an electric field around 1.4 kV/cm in a RTP rectangular slab of the same total length and, in this case, the group delay is of the order of a few fs.

  10. Precise real-time polarization measurement of terahertz electromagnetic waves by a spinning electro-optic sensor.

    Science.gov (United States)

    Yasumatsu, Naoya; Watanabe, Shinichi

    2012-02-01

    We propose and develop a method to quickly and precisely determine the polarization direction of coherent terahertz electromagnetic waves generated by femtosecond laser pulses. The measurement system consists of a conventional terahertz time-domain spectroscopy system with the electro-optic (EO) sampling method, but we add a new functionality in the EO crystal which is continuously rotating with the angular frequency ω. We find a simple yet useful formulation of the EO signal as a function of the crystal orientation, which enables a lock-in-like detection of both the electric-field amplitude and the absolute polarization direction of the terahertz waves with respect to the probe laser pulse polarization direction at the same time. The single measurement finishes around two periods of the crystal rotations (∼21 ms), and we experimentally prove that the accuracy of the polarization measurement does not suffer from the long-term amplitude fluctuation of the terahertz pulses. Distribution of the measured polarization directions by repeating the measurements is excellently fitted by a gaussian distribution function with a standard deviation of σ = 0.56°. The developed technique is useful for the fast direct determination of the polarization state of the terahertz electromagnetic waves for polarization imaging applications as well as the precise terahertz Faraday or Kerr rotation spectroscopy.

  11. Design and theoretical investigation of a silicon-on-insulator based electro-optical logic gate device

    Science.gov (United States)

    Li, Lei; Qi, Zhipeng; Hu, Guohua; Yun, Binfeng; Zhong, Yuan; Cui, Yiping

    2016-10-01

    A compact electro-optical "NOR" logic gate device based on silicon-on-insulator (SOI) platform is proposed and investigated theoretically. By introducing a hook-type waveguide, the signal could be coupled between the bus and hook-type waveguide to form an optical circuit and realize NOR logic gate. We can easily realize the NOR logical function by the voltage applied on the coupling components. The numerical simulation shows that a high coupling efficiency of more than 99% is obtained at the wavelength of 1550 nm, and the footprint of our device is smaller than 90 μm2. In addition, the response time of the proposed NOR logic gate is 3 ns with a switching voltage of 1.8 V. Moreover, it is demonstrated that such NOR logic gate device could obtain an extinction ratio of 21.8 dB. Thus, it has great potential to achieve high speed response, low power consumption, and small footprint, which fulfill the demands of next-generation on-chip computer multiplex processors.

  12. Self-Raman Nd:YVO4 laser and electro-optic technology for space-based sodium lidar instrument

    Science.gov (United States)

    Krainak, Michael A.; Yu, Anthony W.; Janches, Diego; Jones, Sarah L.; Blagojevic, Branimir; Chen, Jeffrey

    2014-02-01

    We are developing a laser and electro-optic technology to remotely measure Sodium (Na) by adapting existing lidar technology with space flight heritage. The developed instrumentation will serve as the core for the planning of an Heliophysics mission targeted to study the composition and dynamics of Earth's mesosphere based on a spaceborne lidar that will measure the mesospheric Na layer. We present performance results from our diode-pumped tunable Q-switched self-Raman c-cut Nd:YVO4 laser with intra-cavity frequency doubling that produces multi-watt 589 nm wavelength output. The c-cut Nd:YVO4 laser has a fundamental wavelength that is tunable from 1063-1067 nm. A CW External Cavity diode laser is used as a injection seeder to provide single-frequency grating tunable output around 1066 nm. The injection-seeded self-Raman shifted Nd:VO4 laser is tuned across the sodium vapor D2 line at 589 nm. We will review technologies that provide strong leverage for the sodium lidar laser system with strong heritage from the Ice Cloud and Land Elevation Satellite-2 (ICESat-2) Advanced Topographic Laser Altimeter System (ATLAS). These include a space-qualified frequency-doubled 9W @ 532 nm wavelength Nd:YVO4 laser, a tandem interference filter temperature-stabilized fused-silica-etalon receiver and high-bandwidth photon-counting detectors.

  13. Low-loss, silicon integrated, aluminum nitride photonic circuits and their use for electro-optic signal processing.

    Science.gov (United States)

    Xiong, Chi; Pernice, Wolfram H P; Tang, Hong X

    2012-07-11

    Photonic miniaturization requires seamless integration of linear and nonlinear optical components to achieve passive and active functions simultaneously. Among the available material systems, silicon photonics holds immense promise for optical signal processing and on-chip optical networks. However, silicon is limited to wavelengths above 1.1 μm and does not provide the desired lowest order optical nonlinearity for active signal processing. Here we report the integration of aluminum nitride (AlN) films on silicon substrates to bring active functionalities to chip-scale photonics. Using CMOS-compatible sputtered thin films we fabricate AlN-on-insulator waveguides that exhibit low propagation loss (0.6 dB/cm). Exploiting AlN's inherent Pockels effect we demonstrate electro-optic modulation up to 4.5 Gb/s with very low energy consumption (down to 10 fJ/bit). The ultrawide transparency window of AlN devices also enables high speed modulation at visible wavelengths. Our low cost, wideband, carrier-free photonic circuits hold promise for ultralow power and high-speed signal processing at the microprocessor chip level.

  14. Turbulence statistics applied to calculate expected turbulence-induced scintillation effects on electro-optical systems in different climatic regions

    Science.gov (United States)

    Weiss-Wrana, Karin R.

    2005-08-01

    The refractive-index structure parameter Cn2 is the parameter most commonly used to describe the optically active turbulence. In the past, FGAN-FOM carried out long-term experiments in moderate climate (Central Europe, Germany), arid (summer), and semiarid (winter) climate (Middle East, Israel). Since Cn2 usually changes as a function of time of day and of season its influence on electro-optical systems should be expressed in a statistical way. We composed a statistical data base of Cn2 values. The cumulative frequency of occurrence was calculated for a time interval of two hours around noon (time of strongest turbulence), at night, and around sunrise (time of weakest turbulence) for an arbitrarily selected period of one month in summer and in winter. In October 2004 we extended our long-term turbulence experiments to subarctic climate (North Europe, Norway). First results of our turbulence measurement over snow-covered terrain indicate Cn2 values which are similar or even higher than measured values in Central European winter. The statistical data base was used to calculate the expected turbulence-induced aperture-averaged scintillation index for free-space optical systems (FSO system) in different climates. The calculations were performed for commercially available FSO systems with wavelength of 785 nm and 1.55 µm respectively and with aperture diameters of the receiver of 60 mm and 150 mm for horizontal path at two heights, 2.3 m and 10 m above ground.

  15. Highly precise and accurate terahertz polarization measurements based on electro-optic sampling with polarization modulation of probe pulses.

    Science.gov (United States)

    Nemoto, Natsuki; Higuchi, Takuya; Kanda, Natsuki; Konishi, Kuniaki; Kuwata-Gonokami, Makoto

    2014-07-28

    We have developed an electro-optic (EO) sampling method with polarization modulation of probe pulses; this method allows us to measure the direction of a terahertz (THz) electric-field vector with a precision of 0.1 mrad in a data acquisition time of 660 ms using a 14.0-kHz repetition rate pulsed light source. Through combination with a THz time-domain spectroscopy technique, a time-dependent two-dimensional THz electric field was obtained. We used a photoelastic modulator for probe-polarization modulation and a (111)-oriented zincblende crystal as the EO crystal. Using the tilted pulse front excitation method with stable regeneratively amplified pulses, we prepared stable and intense THz pulses and performed pulse-by-pulse analog-to-digital conversion of the signals. These techniques significantly reduced statistical errors and enabled sub-mrad THz polarization measurements. We examined the performance of this method by measuring a wire-grid polarizer as a sample. The present method will open a new frontier of high-precision THz polarization sensitive measurements.

  16. A novel twisted nematic alignment and its effects on the electro-optical dynamics of nanoscale liquid crystalline films

    Science.gov (United States)

    Rauzan, Brittany; Lee, Lay Min; Nuzzo, Ralph

    2015-03-01

    Vibrational spectroscopic studies of a surface induced, twisted alignment of the nematic liquid crystal, 4-n-pentyl-4'-cyanobiphenyl (5CB) and its temperature-dependent electro-optical (EO) dynamics were studied near the crystalline-nematic and nematic-isotropic transition temperatures, and at a median temperature in the nematic phase. A 50 nm thick film of 5CB was confined in nanocavities defined by the dimensions of a gold interdigitated electrode array patterned on a unidirectionally polished ZnSe substrate. The film was assembled between two polished substrates bearing extended nanometer-scaled grooves that are oriented orthogonally to one another. The results show that with this anchoring scheme, the molecular director of the LC film undergoes a ninety-degree twist. Step-scan time resolved spectroscopy (TRS) measurements were made to determine the rate constants for the temperature-dependent EO dynamics of both the electric field-induced orientation and thermal relaxation processes of the LC film. The work rationalizes the impacts of organizational anisotropy and illustrates how it can be exploited as a design principle to effectively influence the electric field-induced dynamics of LC systems.

  17. Effect of MWCNTs on the electro-optic properties of 5CB LC cells during the Freedericksz Transition

    Science.gov (United States)

    Eakle, Matthew; Georgiev, Georgi; Atherton, Timothy; Cebe, Peggy

    2014-03-01

    Multi-walled carbon nanotubes (MWCNTs) affect the electro-optic properties of liquid crystals, but the mechanisms of interaction between the two remain not well understood. To address this, we are investigating the effect of alternating electric fields on the optical properties and Freedericksz Transition of 5CB liquid crystal with different concentrations of MWCNTs. 5CB cells with ITO electrodes were made using spin-coated PVA for sample alignment and MylarTM spacer films to control the thickness, which ranged from 12 to 23 microns. Transmission optical ellipsometry was used to measure the optical retardance (phase delay) and uniaxial director angle of 5CB liquid crystals as the peak voltage of a high-frequency (1 kHz - 1 MHz) AC electric field was varied from 0 to 10 V. For constant frequency, the Freedericksz Transition was noted by a sharp decrease in retardance from an initial plateau, which gradually decreased toward zero as the voltage increased. With increasing frequency, the decay broadened and the Freedericksz Transition occurred at higher voltage. Numerical simulations of CNT-facilitated switching are also presented. Research was funded by the National Science Foundation, Polymers Program of the Division of Materials Research, through DMR-12061010.

  18. Low-loss, silicon integrated, aluminum nitride photonic circuits and their use for electro-optic signal processing

    CERN Document Server

    Xiong, Chi; Tang, Hong X

    2014-01-01

    Photonic miniaturization requires seamless integration of linear and nonlinear optical components to achieve passive and active functions simultaneously. Among the available material systems, silicon photonics holds immense promise for optical signal processing and on-chip optical networks. However, silicon is limited to wavelengths above 1100 nm and does not provide the desired lowest order optical nonlinearity for active signal processing. Here we report the integration of aluminum nitride (AlN) films on silicon substrates to bring active functionalities to chip-scale photonics. Using CMOS-compatible sputtered thin films we fabricate AlN-on-insulator waveguides that exhibit low propagation loss (0.6 dB/cm). Exploiting AlN's inherent Pockels effect we demonstrate electro-optic modulation up to 4.5 Gb/s with very low energy consumption (down to 10 fJ/bit). The ultra-wide transparency window of AlN devices also enables high speed modulation at visible wavelengths. Our low cost, wideband, carrier-free photonic ...

  19. Multi-Site Simultaneous Time-Resolved Photometry with a Low Cost Electro-Optics System †

    Science.gov (United States)

    Gasdia, Forrest; Barjatya, Aroh; Bilardi, Sergei

    2017-01-01

    Sunlight reflected off of resident space objects can be used as an optical signal for astrometric orbit determination and for deducing geometric information about the object. With the increasing population of small satellites and debris in low Earth orbit, photometry is a powerful tool in operational support of space missions, whether for anomaly resolution or object identification. To accurately determine size, shape, spin rate, status of deployables, or attitude information of an unresolved resident space object, multi-hertz sample rate photometry is required to capture the relatively rapid changes in brightness that these objects can exhibit. OSCOM, which stands for Optical tracking and Spectral characterization of CubeSats for Operational Missions, is a low cost and portable telescope system capable of time-resolved small satellite photometry, and is field deployable on short notice for simultaneous observation from multiple sites. We present the electro-optical design principles behind OSCOM and light curves of the 1.5 U DICE-2 CubeSat and simultaneous observations of the main body of the ASTRO-H satellite after its fragmentation event. PMID:28556802

  20. Broadband energy-efficient optical modulation by hybrid integration of silicon nanophotonics and organic electro-optic polymer

    CERN Document Server

    Zhang, Xingyu; Subbaraman, Harish; Luo, Jingdong; Jen, Alex K -Y; Chung, Chi-jui; Yan, Hai; Pan, Zeyu; Nelson, Robert L; Chen, Ray T

    2015-01-01

    Silicon-organic hybrid integrated devices have emerging applications ranging from high-speed optical interconnects to photonic electromagnetic-field sensors. Silicon slot photonic crystal waveguides (PCWs) filled with electro-optic (EO) polymers combine the slow-light effect in PCWs with the high polarizability of EO polymers, which promises the realization of high-performance optical modulators. In this paper, a broadband, power-efficient, low-dispersion, and compact optical modulator based on an EO polymer filled silicon slot PCW is presented. A small voltage-length product of V{\\pi}*L=0.282Vmm is achieved, corresponding to an unprecedented record-high effective in-device EO coefficient (r33) of 1230pm/V. Assisted by a backside gate voltage, the modulation response up to 50GHz is observed, with a 3-dB bandwidth of 15GHz, and the estimated energy consumption is 94.4fJ/bit at 10Gbit/s. Furthermore, lattice-shifted PCWs are utilized to enhance the optical bandwidth by a factor of ~10X over other modulators bas...

  1. Optical Vector Network Analyzer with an Improved Dynamic Range Based on a Polarization Multiplexing Electro-Optic Modulator

    Science.gov (United States)

    Wang, Qi; Wang, Wen-Ting; Chen, Wei; Liu, Jian-Guo; Zhu, Ning-Hua

    2017-05-01

    We present a new method to achieve an optical vector network analyzer (OVNA) based on a polarization multiplexing electro-optic modulator (PM-EOM) without an optical bandpass filter. Optical single sideband (OSSB) modulated signals with a tunable optical carrier-sideband ratio (OCSR) are obtained at the output of the PM-EOM. The OCSR can be flexibly tuned by controlling bias voltages of the PM-EOM. The dynamic range of the OVNA is expanded by taking the improvement of the OCSR into account. The transmission response of an optical device under test (ODUT) is measured based on one-to-one mapping from optical domain to electrical domain. By optimizing the OCSR of the OSSB modulated signals, the dynamic range of the OVNA can be effectively improved with 3.7 dB. An analytical model is derived to describe the transfer function of the ODUT. The magnitude and phase responses of a fiber Bragg grating are characterized with a large dynamic range. Supported by the National Natural Science Foundation of China under Grant Nos 61377070, 61090391 and 61675196, and the National High-Technology Research and Development Program of China under Grant No 2013AA014203.

  2. Readout strategy of an electro-optical coupled PET detector for time-of-flight PET/MRI

    Science.gov (United States)

    Bieniosek, M. F.; Olcott, P. D.; Levin, C. S.

    2013-10-01

    Combining PET with MRI in a single system provides clinicians with complementary molecular and anatomical information. However, existing integrated PET/MRI systems do not have time-of-flight (ToF) PET capabilities. This work describes an MRI-compatible front-end electronic system with ToF capabilities. The approach employs a fast arrival-time pickoff comparator to digitize the timing information, and a laser diode to drive a 10 m fiber-optic cable to optically transmit asynchronous timing information to a photodiode receiver readout system. The FWHM jitter of the comparator and this electo-optical link is 11.5 ps in response to a fast digital pulse. When configured with LYSO scintillation crystals and Hamamatsu MPPC silicon photo-multipliers the comparator and electro-optical link achieved a 511 keV coincidence time resolution of 254.7 ps +/- 8.0 ps FWHM with 3 × 3 × 20 mm3 crystals and 166.5 +/- 2.5 ps FWHM with 3 × 3 × 5 mm3 crystals.

  3. Electro-optic prism-pair setup for efficient high bandwidth isochronous CEP phase shift or group delay generation

    Science.gov (United States)

    Gobert, Olivier; Mennerat, Gabriel; Cornaggia, Christian; Lupinski, Dominique; Perdrix, Michel; Guillaumet, Delphine; Lepetit, Fabien; Oksenhendler, Thomas; Comte, Michel

    2016-05-01

    We report the experimental demonstration of an electro-optic prism pair pure carrier-envelope phase (CEP) shifter at low voltage (shift of 1 rad for a voltage of 90 V, applied to a crystal of 5 mm aperture). Validating our mathematical model, the experiments prove that this set-up which uses two rubidium titanyl phosphate (RTP) crystals, can be used either as an efficient high bandwidth CEP shifter without modifying the group delay of an ultrashort pulse (isochronous CEP shifter) or alternatively as a group delay generator with quasi-constant CEP (Pure Group Delay generator). These two configurations which correspond to specific geometries are characterized by spectral interferometry with a 800 nm mode-locked Ti:sapphire laser. The results are in very good agreement with the model. In the pure group delay mode, a group delay of 2.3 fs is obtained at 1000 V/cm without significant CEP shift. In the isochronous mode, a shift of 5.5 rad at 1000 V/cm is generated without significant delay. The applied voltage is also lowered by a factor of nearly three in this configuration, compared to the case of an RTP rectangular slab of the same total length.

  4. Dielectric and electro-optic studies of a bimesogenic liquid crystal composed of bent-core and calamitic units.

    Science.gov (United States)

    Balachandran, R; Panov, V P; Vij, J K; Shanker, G; Tschierske, C; Merkel, K; Kocot, A

    2014-09-01

    A bimesogen, BR1, composed of a bent-core and calamitic unit, linked laterally via a flexible spacer is investigated by dielectric and electro-optic techniques. X-ray results show the presence of clusters in the nematic phase, and the cluster size is of the order of the thickness of a single layer. The splitting of the small-angle scattering Δχ/2 is about 50°, which indicates SmC like clusters with a significant tilt of the molecules in the quasilayers. The sign reversal of the dielectric anisotropy Δε' is observed as a function of frequency; the behavior is rather similar to that exhibited by the conventional dual frequency nematics, composed of a calamitic mesogen, with the exception that it occurs at much lower frequencies in this material. Interestingly, as the bimesogen enters its nematic phase, the average permittivity decreases as the temperature is lowered. This indicates the onset of antiparallel association of some of the dipoles in the system, and this type of association is much more prominent in BR1 in comparison to other bent-core liquid crystalline systems composed of the same bisbenzoate core unit. The analysis of the dielectric spectra using the Maier-Meier model confirms the onset of an antiparallel correlation of dipoles occurring at the isotropic to nematic phase transition temperature. Additionally these results support a model of the cluster where the transverse dipole moments in the neighboring layers are antiparalleled to each other.

  5. Self-Raman Nd:YVO4 Laser and Electro-Optic Technology for Space-Based Sodium Lidar Instrument

    Science.gov (United States)

    Krainak, Michael A.; Yu, Anthony W.; Janches, Diego; Jones, Sarah L.; Blagojevic, Branimir; Chen, Jeffrey

    2014-01-01

    We are developing a laser and electro-optic technology to remotely measure Sodium (Na) by adapting existing lidar technology with space flight heritage. The developed instrumentation will serve as the core for the planning of an Heliophysics mission targeted to study the composition and dynamics of Earth's mesosphere based on a spaceborne lidar that will measure the mesospheric Na layer. We present performance results from our diode-pumped tunable Q-switched self-Raman c-cut Nd:YVO4 laser with intra-cavity frequency doubling that produces multi-watt 589 nm wavelength output. The c-cut Nd:YVO4 laser has a fundamental wavelength that is tunable from 1063-1067 nanometers. A CW (Continuous Wave) External Cavity diode laser is used as a injection seeder to provide single-frequency grating tunable output around 1066 nanometers. The injection-seeded self-Raman shifted Nd:VO4 laser is tuned across the sodium vapor D2 line at 589 nanometers. We will review technologies that provide strong leverage for the sodium lidar laser system with strong heritage from the Ice Cloud and Land Elevation Satellite-2 (ICESat-2) Advanced Topographic Laser Altimeter System (ATLAS). These include a space-qualified frequency-doubled 9 watts-at-532-nanometer wavelength Nd:YVO4 laser, a tandem interference filter temperature-stabilized fused-silica-etalon receiver and high-bandwidth photon-counting detectors.

  6. Ultralow-phase-noise millimetre-wave signal generator assisted with an electro-optics-modulator-based optical frequency comb.

    Science.gov (United States)

    Ishizawa, A; Nishikawa, T; Goto, T; Hitachi, K; Sogawa, T; Gotoh, H

    2016-05-17

    Low-noise millimetre-wave signals are valuable for digital sampling systems, arbitrary waveform generation for ultra-wideband communications, and coherent radar systems. However, the phase noise of widely used conventional signal generators (SGs) will increase as the millimetre-wave frequency increases. Our goal has been to improve commercially available SGs so that they provide a low-phase-noise millimetre-wave signal with assistance from an electro-optics-modulator-based optical frequency comb (EOM-OFC). Here, we show that the phase noise can be greatly reduced by bridging the vast frequency difference between the gigahertz and terahertz ranges with an EOM-OFC. The EOM-OFC serves as a liaison that magnifies the phase noise of the SG. With the EOM-OFC used as a phase noise "booster" for a millimetre-wave signal, the phase noise of widely used SGs can be reduced at an arbitrary frequency f (6 ≦ f ≦ 72 GHz).

  7. Electro-optical switching at 1550 nm using a two-state GeSe phase-change layer.

    Science.gov (United States)

    Soref, Richard; Hendrickson, Joshua; Liang, Haibo; Majumdar, Arka; Mu, Jianwei; Li, Xun; Huang, Wei-Ping

    2015-01-26

    New designs for electro-optical free-space and waveguided 2 x 2 switches are presented and analyzed at the 1.55 μm telecoms wavelength. The proposed devices employ a ~10 nm film of GeSe that is electrically actuated to transition the layer forth-and-back from the amorphous to the crystal phase, yielding a switch with two self-sustaining states. This phase change material was selected for its very low absorption loss at the operation wavelength, along with its electro-refraction Δn ~0.6. All switches are cascadeable into N x M devices. The free-space prism-shaped structures use III-V prism material to match the GeSe crystal index. The Si/GeSe/Si "active waveguides" are quite suitable for directional-coupler switches as well as Mach-Zehnder devices-all of which have an active length 16x less than that in the free-carrier art.

  8. A Preliminary Rubric Design to Evaluate Mixed Methods Research

    Science.gov (United States)

    Burrows, Timothy J.

    2013-01-01

    With the increase in frequency of the use of mixed methods, both in research publications and in externally funded grants there are increasing calls for a set of standards to assess the quality of mixed methods research. The purpose of this mixed methods study was to conduct a multi-phase analysis to create a preliminary rubric to evaluate mixed…

  9. Connecticut Transit (CTTRANSIT) Fuel Cell Transit Bus: Preliminary Evaluation Results

    Energy Technology Data Exchange (ETDEWEB)

    Chandler, K.; Eudy, L.

    2008-10-01

    This report provides preliminary results from a National Renewable Energy Laboratory evaluation of a protoptye fuel cell transit bus operating at Connecticut Transit in Hartford. Included are descriptions of the planned fuel cell bus demonstration and equipment; early results and agency experience are also provided.

  10. A Preliminary Rubric Design to Evaluate Mixed Methods Research

    Science.gov (United States)

    Burrows, Timothy J.

    2013-01-01

    With the increase in frequency of the use of mixed methods, both in research publications and in externally funded grants there are increasing calls for a set of standards to assess the quality of mixed methods research. The purpose of this mixed methods study was to conduct a multi-phase analysis to create a preliminary rubric to evaluate mixed…

  11. Preliminary technical and economic evaluation of vortex extraction devices

    Energy Technology Data Exchange (ETDEWEB)

    Kornreich, T. R.; Kottler, Jr., R. J.; Jennings, D. M.

    1980-04-01

    Two innovative vortex extraction devices - the Tornado Wind Energy System (TWES) and the Vortex Augmentor Concept (VAC) - are critically evaluated to provide a preliminary assessment of their technical and economic viability as compared to conventional horizontal axis wind energy systems. This assessment was carried out over a wide range of power output levels and augmentation ratios appropriate to each of the concepts.

  12. Outline and Preliminary Evaluation of the Classical Digital Library Model.

    Science.gov (United States)

    MacCall, Steven L.; Cleveland, Ana D.; Gibson, Ian E.

    1999-01-01

    Outlines the classical digital library model, which is derived from traditional practices of library and information science professionals, as an alternative to the database retrieval model. Reports preliminary results from an evaluation study of library and information professionals and endusers involved with primary care medicine. (AEF)

  13. Preliminary Clinical Evaluation: The What, Where, How Approach to Scoring

    OpenAIRE

    Wright, C.; Akimoto, T.

    2016-01-01

    The SCoR is driving for preliminary clinical evaluation (PCE) however; currently there is no method of quantification to assess quality. FRCR has an approach to quantify comments in the rapid reporting examination (CR2B).The aim of this project was to develop a robust scoring system that enables comprehensive image evaluation regardless of profession. An image test bank was administered using RadBench with equal prevalence of normal /abnormal. A random sample of attempts was selected to pilot...

  14. Preliminary evaluation of a Neutron Calibration Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Alvarenga, Talysson S.; Neves, Lucio P.; Perini, Ana P.; Sanches, Matias P.; Mitake, Malvina B.; Caldas, Linda V.E., E-mail: talvarenga@ipen.br, E-mail: lpneves@ipen.br, E-mail: aperini@ipen.br, E-mail: msanches@ipen.br, E-mail: mbmitake@ipen.br, E-mail: lcaldas@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Federico, Claudio A., E-mail: claudiofederico@ieav.cta.br [Instituto de Estudos Avancados (IEAv/DCTA), Sao Jose dos Campos, SP (Brazil). Dept. de Ciencia e Tecnologia Aeroespacial

    2013-07-01

    In the past few years, Brazil and several other countries in Latin America have experimented a great demand for the calibration of neutron detectors, mainly due to the increase in oil prospection and extraction. The only laboratory for calibration of neutron detectors in Brazil is localized at the Institute for Radioprotection and Dosimetry (IRD/CNEN), Rio de Janeiro, which is part of the IAEA SSDL network. This laboratory is the national standard laboratory in Brazil. With the increase in the demand for the calibration of neutron detectors, there is a need for another calibration services. In this context, the Calibration Laboratory of IPEN/CNEN, Sao Paulo, which already offers calibration services of radiation detectors with standard X, gamma, beta and alpha beams, has recently projected a new calibration laboratory for neutron detectors. In this work, the ambient equivalent dose rate (H⁎(10)) was evaluated in several positions inside and around this laboratory, using Monte Carlo simulation (MCNP5 code), in order to verify the adequateness of the shielding. The obtained results showed that the shielding is effective, and that this is a low-cost methodology to improve the safety of the workers and evaluate the total staff workload. (author)

  15. An electro-optical timing diagnostic for pump-probe experiments at the free-electron laser in Hamburg FLASH

    Energy Technology Data Exchange (ETDEWEB)

    Azima, Armin

    2009-07-15

    Femtosecond pump-probe experiments have extensively been used to follow atomic and molecular motion in time. The very intense extreme ultraviolet XUV light of the Free electron LASer in Hamburg FLASH facility allows to investigate fundamental processes such as direct one or few photon inner shell ionizations. A supplementary Ti:Sapphire near infrared femtosecond laser system allows to perform two-color pump-probe experiments with FLASH involving intense laser fields of hugely different photon energies. Within this work a bunch arrival measurement system has been built, which assists these two-color pump-probe experiments to reduce the temporal jitter of FLASH and to increase the temporal resolution. The diagnostic is based upon an electro-optical detection scheme and measures the relative arrival time between the Ti:Sapphire femtosecond pulse and the electron bunch, which generates the self-amplified by stimulated emission SASE XUV pulse in the undulator section of FLASH. Key feature of the diagnostic is a 150 m long glass fiber pulse transport line, which inflicts non-linear dispersion. A dispersion control system to compensate for this higher order dispersion has been developed including the control and programming of a spatial light phase modulator. It was possible to transport a 90 fs FWHM short near infrared femtosecond laser pulse Fourier limited by the dispersion compensated glass fiber. The electro-optical signal induced by the FLASH electron bunch was generated, characterized and optimized. The signal features beside the designated bunch arrival timing capability the additional possibility to measure the longitudinal electron bunch density distribution of an arbitrary bunch of FLASH in a single shot with a temporal resolution of below 100 fs RMS. Timing and bunch analysis capabilities of the developed diagnostic have been cross-checked with other comparable diagnostics at FLASH like the transversal deflecting cavity structure named LOLA. Finally, the

  16. Data Base Descriptors for Electro-Optical Sensor Simulation. Final Report, May 1977 through June 1978.

    Science.gov (United States)

    Zimmerlin, Timothy A.; And Others

    An effort to construct a model of the thermal properties of materials based on theoretical thermo-electromagnetic models, to construct a data base of the dense cultural hospital scene according to Defense Mapping Agency Aerospace Center (DMAAC) specifications, and to design and implement a program to evaluate the tonal model and generate imagery…

  17. Feasibility study of a single-shot 3D electron bunch shape monitor with an electro-optic sampling technique

    Directory of Open Access Journals (Sweden)

    Yuichi Okayasu

    2013-05-01

    Full Text Available We developed a three-dimensional electron bunch charge distribution (3D-BCD monitor with single-shot detection, and a spectral decoding based electro-optic (EO sampling technique for a nondestructive monitor enables real-time reconstruction of the three-dimensional distribution of a bunch charge. We realized three goals by simultaneously probing a number of Pockels EO crystals that surround the electron beam axis with hollow and radial polarized laser pulses. First, we performed a feasibility test as a simple case of a 3D-BCD monitor probing two ZnTe crystals as EO detectors installed on the opposite angle to the electron beam axis and confirmed that we simultaneously obtained both EO signals. Since the adopted hollow probe laser pulse is not only radially polarized but also temporally shifted azimuthally, some disorders in the radial polarization distribution of such a laser pulse were numerically analyzed with a plane-wave expansion method. Based on the above investigations, the 3D-BCD monitor is feasible both in experimental and numerical estimations. Furthermore, we previously developed a femtosecond response organic crystal as a Pockels EO detector and a broadband probe laser (≥350  nm in FWHM; the 3D-BCD monitor realizes 30- to 40-fs (FWHM temporal resolution. Eventually, the monitor is expected to be equipped in such advanced accelerators as XFEL to measure and adjust the electron bunch charge distribution in real time. The 3D-BCD measurement works as a critical tool to provide feedback to seeded FELs.

  18. Anchoring and electro-optical dynamics of thin liquid crystalline films in a polyimide cell: Experiment and theory

    Science.gov (United States)

    Lee, Lay Min; Kwon, Hye J.; Kang, Joo H.; Nuzzo, Ralph G.; Schweizer, Kenneth S.

    2006-07-01

    The surface-dependent anchoring and electro-optical (EO) dynamics of thin liquid crystalline films have been examined using Fourier transform infrared spectroscopy. A simple nematic liquid crystal, 4-n-pentyl-4'-cyanobiphenyl (5CB), is confined as 40, 50, and 390nm thick films in nanocavities defined by gold interdigitated electrode arrays (IDEAs) patterned on polyimide-coated zinc selenide (ZnSe) substrates [Noble et al., J. Am. Chem. Soc. 124, 15020 (2002)]. New strategies for controlling the anchoring interactions and EO dynamics are explored based on coating a ZnSe surface with an organic polyimide layer in order to both planarize the substrate and induce a planar alignment of the liquid crystalline film. The polyimide layer can be further treated so as to induce a strong alignment of the nematic director along a direction parallel to the electrode digits of the IDEA. Step-scan time-resolved spectroscopy measurements were made to determine the rate constants for the electric-field-induced orientation and thermal relaxation of the 5CB films. In an alternate set of experiments, uncoated ZnSe substrates were polished unidirectionally to produce a grooved surface presenting nanometer-scale corrugations. The dynamical rate constants measured for several nanoscale film thicknesses and equilibrium organizations of the director in these planar alignments show marked sensitivities. The orientation rates are found to vary strongly with both the magnitude of the applied potential and the initial anisotropy of the alignment of the director within the IDEA. The relaxation rates do not vary in this same way. The marked variations seen in EO dynamics can be accounted for by a simple coarse-grained dynamical model.

  19. Coherent combining of fiber-laser-pumped frequency converters using all fiber electro-optic modulator for active phase control

    Science.gov (United States)

    Bourdon, P.; Durécu, A.; Canat, G.; Le Gouët, J.; Goular, D.; Lombard, L.

    2015-03-01

    Coherent beam combining (CBC) by active phase control could be useful for power scaling fiber-laser-pumped optical frequency converters like OPOs. However, a phase modulator operating at the frequency-converted wavelength is needed, which is non standard component. Fortunately, nonlinear conversion processes rely on a phase-matching condition correlating, not only the wave vectors of the coupled waves, but also their phases. This paper demonstrates that, using this phase correlation for indirect control of the phase, coherent combining of optical frequency converters is feasible using standard all-fibered electro-optic modulators. For the sake of demonstration, this new technique is experimentally applied twice for continuous wave second-harmonic-generator (SHG) combination: i) combining 2 SHG of 1.55-μm erbium-doped fiber amplifiers in PPLN crystals generating 775-nm beams; ii) combining 2 SHG of 1.064-μm ytterbium-doped fiber amplifiers in LBO crystals generating 532-nm beams. Excellent CBC efficiency is achieved on the harmonic waves in both these experiments, with λ/20 and λ/30 residual phase error respectively. In the second experiment, I/Q phase detection is added on fundamental and harmonic waves to measure their phase variations simultaneously. These measurements confirm the theoretical expectations and formulae of correlation between the phases of the fundamental and harmonic waves. Unexpectedly, in both experiments, when harmonic waves are phase-locked, a residual phase difference remains between the fundamen tal waves. Measurements of the spectrum of these residual phase differences locate them above 50 Hz, revealing that they most probably originate in fast-varying optical path differences induced by turbulence and acoustic-waves on the experimental breadboard.

  20. Frequency measurement of THz waves by electro-optic sampling using Mach-Zehnder-modulator-based flat comb generator

    Science.gov (United States)

    Morohashi, Isao; Kirigaya, Mayu; Kaneko, Yuta; Katayama, Ikufumi; Sakamoto, Takahide; Sekine, Norihiko; Kasamatsu, Akifumi; Hosako, Iwao

    2016-02-01

    In the recent progress in terahertz (THz) devices, various kinds of source devices, such as resonant tunneling diodes, quantum cascade lasers and so forth, have been developed. Frequency measurement of THz radiations, which can operate in high speed and at room-temperature, is important for development of high-performance THz source devices. Recently, frequency measurement using optical combs are demonstrated by several groups. In these techniques, modelocked lasers (MLLs) are used for optical comb source, so that phase-locking techniques are required in order to stabilize the repetition frequency of the MLLs. On the other hand, a modulator-based optical comb generator has high accuracy and stability in the comb spacing, which is comparable to that of microwave signal driving the modulator. Thus it is suitable for frequency measurement of THz waves. In this paper, we demonstrated frequency measurement of THz waves using a Mach-Zehnder-modulator-based flat comb generator (MZ-FCG). The frequency measurement was carried out by an electro-optic (EO) sampling method, where an optical two-tone signal extracted from the optical comb generated by the MZ-FCG was used for the probe light. A 100 GHz signal generated by a W-band frequency multiplier and the probe beam collinearly traveled through an EO crystal, and beat signals between them were measured by a combination of a balanced photodetector and a spectrum analyzer. As a result, frequency measurement of the 100 GHz wave was successfully demonstrated, in which the linewidth of the beat signal was less than 1 Hz.

  1. Microelectronics Instrument Products Shock and Vibration Electro-optics: C-Qualification Test Report

    Science.gov (United States)

    1994-01-01

    In this test report all measurements made during testing are recorded in ATP 20049 DS data sheets and are included in the log. The motor/encoder (henceforth referred to as the UUT) test sequence began with a baseline functional evaluation, which demonstrated that the motor satisfied the operating torque, cogging torque, winding resistance, and mechanical requirements of SOW. In addition, the encoder electrical requirements were verified, as well as the alignment of the encoder outputs relative tc, the motor shaft position. There were no discrepancies observed in this portion of the test. The UUT was then exposed to a number of environments, including thermal vacuum, thermal cycling, random and sine vibration, and mechanical shock. During the thermal environments, the performance of the UUT under load was verified at specified points in the cycles, as described in ATP 20049. In addition, the UUT was bench tested between the two thermal environments. No anomalies were observed during the thermal tests. The load attachment method was subsequently corrected, and vibration of S/N 0002 began while 0003 was being repaired.

  2. Microelectronics Instrument Products Shock and Vibration Electro-Optics. Section B; Acceptance Data Package

    Science.gov (United States)

    1995-01-01

    The motor/encoder (henceforth referred to as the UUT) test sequence began with a baseline functional evaluation, which demonstrated that the motor satisfied the operating torque, cogging torque, winding resistance, and mechanical requirements of SOW. In addition, the encoder electrical requirements were verified, as well as the alignment of the encoder outputs relative to the motor shaft position. There were no discrepancies observed in this portion of the test. The UUT was then exposed to a number of environments, including thermal vacuum, thermal cycling, random and sine vibration, and mechanical shock. During the thermal environments, the performance of the UUT under load was verified at specified points in the cycles, as described in ATP 20049. In addition, the UUT was bench tested between the two thermal environments. No anomalies were observed during the thermal tests. The vibration and shock tests were performed by East-West Technology Corporation, West Babylon, New York. The UUT was delivered to the lab in a sealed vibration fixture in order to maintain the cleanliness levels required by the SOW. In addition, a three ounce load was attached to the motor shaft. The attachment method of this load caused damage to the shaft and bearing during random vibration of S/N 0003 on April 28, 1995, and is described further in NCR 00168.

  3. Analog electro-optical readout of SiPMs achieves fast timing required for time-of-flight PET/MR.

    Science.gov (United States)

    Bieniosek, M F; Levin, C S

    2015-05-07

    The design of combined positron emission tomography/magnetic resonance (PET/MR) systems presents a number of challenges to engineers, as it forces the PET system to acquire data in a space constrained environment that is sensitive to electro-magnetic interference and contains high static, radio frequency and gradient fields. In this work we validate fast timing performance of a PET scintillation detector using a potentially very compact, very low power, and MR compatible readout method in which analog silicon photomultipliers (SiPM) signals are transmitted optically away from the MR bore with little or even no additional readout electronics. This analog 'electro-optial' method could reduce the entire PET readout in the MR bore to two compact, low power components (SiPMs and lasers). Our experiments show fast timing performance from analog electro-optical readout with and without pre-amplification. With 3 mm × 3 mm × 20 mm lutetium-yttrium oxyorthosilicate (LYSO) crystals and Excelitas SiPMs the best two-sided fwhm coincident timing resolution achieved was 220 +/- 3 ps in electrical mode, 230 +/- 2 ps in electro-optical with preamp mode, and 253 +/- 2 ps in electro-optical without preamp mode. Timing measurements were also performed with Hamamatsu SiPMs and 3 mm × 3 mm × 5 mm crystals. In the future the timing degradation seen can be further reduced with lower laser noise or improvements SiPM rise time or gain.

  4. Precise calculation of the KTP crystal used as both an intracavity electro-optic Q-switch and a second harmonic generator

    Institute of Scientific and Technical Information of China (English)

    Yuye Wang; Jianquan Yao; Degang Xu; Pu Zhao; Peng Wang

    2006-01-01

    @@ A method of precisely calculating the external applied voltage and the optimum type-Ⅱ phase matching angles for KTP crystal, which is used as both an intracavity electro-optic (EO) Q-switch and a frequency doubler, is presented. The effective EO coefficient along the phase-matching direction is defined to calculate the half-wave voltage and the quarter-wave voltage, and the precise calculation for the phase matching angles in the condition of KTP crystal optimum second harmonic phase matching is theoretically realized.

  5. Design of Excess 3 to BCD code converter using electro-optic effect of Mach-Zehnder Interferometers for efficient data transmission

    Science.gov (United States)

    Kumar, Santosh; Chanderkanta; Amphawan, Angela

    2016-04-01

    Excess 3 code is one of the most important codes used for efficient data storage and transmission. It is a non-weighted code and also known as self complimenting code. In this paper, a four bit optical Excess 3 to BCD code converter is proposed using electro-optic effect inside lithium-niobate based Mach-Zehnder interferometers (MZIs). The MZI structures have powerful capability to switching an optical input signal to a desired output port. The paper constitutes a mathematical description of the proposed device and thereafter simulation using MATLAB. The study is verified using beam propagation method (BPM).

  6. Novel electro-optical phase modulator based on GaInAs/InP modulation-doped quantum-well structures

    DEFF Research Database (Denmark)

    Thirstrup, C.

    1992-01-01

    A novel electro-optical phase modulator working at 1.55 µm is analyzed and proposed. It is shown by a numerical model that in a GaInAs/InP pn-nin-pn multiple-quantum-well waveguide structure, large optical phase modulation can be obtained at small intensity modulation and with improved performance...... compared to what is achieved in quantum confined Stark effect modulators of the same material system. The device proposed is based on a modulation of the quasi-Fermi energies of the electrons in the GaInAs quantum wells. This operational principle allows GHz modulation frequencies. Applied Physics Letters...

  7. Design and application of airborne electro-optical detection system performance quantificational IR drone%机载光电探测系统红外性能测试靶板的研究

    Institute of Scientific and Technical Information of China (English)

    郁品一; 张平鑫; 胡磊力; 李艳晓

    2012-01-01

    为了对机载光电探测系统外场性能进行定量评价,设计了野外红外性能测试靶板,论述了该靶板的设计、原理、结构、标定和应用,利用该靶板可以开展不同气象条件下系统的作用距离、探测灵敏度、空间分辨率、温度分辨率、点目标探测等性能测试研究.%To quantitatively measure and evaluate the performance of Airborne Electro-optical Detection system,a field lest equipment is designed. The theory of the IR drone,its structure,calibration and application are introduced. With the drone,the parameters of infrared imaging system such as the maximum operation distance,detection sensitivity, spatial resolution and temperature resolution under different weather conditions,can be measured on site.

  8. Design of an optical 4-bit binary to BCD converter using electro-optic effect of lithium niobate based Mach-Zehnder interferometers

    Science.gov (United States)

    Kumar, Santosh

    2017-07-01

    Binary to Binary coded decimal (BCD) converter is a basic building block for BCD processing. The last few decades have witnessed exponential rise in applications of binary coded data processing in the field of optical computing thus there is an eventual increase in demand of acceptable hardware platform for the same. Keeping this as an approach a novel design exploiting the preeminent feature of Mach-Zehnder Interferometer (MZI) is presented in this paper. Here, an optical 4-bit binary to binary coded decimal (BCD) converter utilizing the electro-optic effect of lithium niobate based MZI has been demonstrated. It exhibits the property of switching the optical signal from one port to the other, when a certain appropriate voltage is applied to its electrodes. The projected scheme is implemented using the combinations of cascaded electro-optic (EO) switches. Theoretical description along with mathematical formulation of the device is provided and the operation is analyzed through finite difference-Beam propagation method (FD-BPM). The fabrication techniques to develop the device are also discussed.

  9. Long range surface plasmon resonance enhanced electro-optically tunable Goos-Hänchen shift and Imbert-Fedorov shift in ZnSe prism

    Science.gov (United States)

    Goswami, Nabamita; Kar, Aparupa; Saha, Ardhendu

    2014-11-01

    A new theoretical approach towards the tuning of Goos-Hänchen shift and Imbert-Fedorov shift for the reflected light beam is observed, designed and simulated in this paper through electro-optically tunable liquid crystal at an incident wavelength of 1550 nm within the communication window. Here the considered Kretschmann-Raether geometry comprises a ZnSe prism and a liquid crystal layer of E44 between two metal layers of silver, where with the application of electric field from (0-10) V electro-optically tuning of the Goos-Hänchen shift from 64.09 μm to -53.408 μm and the Imbert-Fedorov shift from 122.8 μm to -32.5 μm for a change in refractive index of the liquid crystal layer from 1.52-1.79 are envisaged. This idea expedites the scope of fine tuning in optical switching within the μm ranges.

  10. Time-resolved absolute measurements by electro-optic effect of giant electromagnetic pulses due to laser-plasma interaction in nanosecond regime

    Science.gov (United States)

    Consoli, F.; de Angelis, R.; Duvillaret, L.; Andreoli, P. L.; Cipriani, M.; Cristofari, G.; di Giorgio, G.; Ingenito, F.; Verona, C.

    2016-06-01

    We describe the first electro-optical absolute measurements of electromagnetic pulses (EMPs) generated by laser-plasma interaction in nanosecond regime. Laser intensities are inertial-confinement-fusion (ICF) relevant and wavelength is 1054 nm. These are the first direct EMP amplitude measurements with the detector rather close and in direct view of the plasma. A maximum field of 261 kV/m was measured, two orders of magnitude higher than previous measurements by conductive probes on nanosecond regime lasers with much higher energy. The analysis of measurements and of particle-in-cell simulations indicates that signals match the emission of charged particles detected in the same experiment, and suggests that anisotropic particle emission from target, X-ray photoionization and charge implantation on surfaces directly exposed to plasma, could be important EMP contributions. Significant information achieved on EMP features and sources is crucial for future plants of laser-plasma acceleration and inertial-confinement-fusion and for the use as effective plasma diagnostics. It also opens to remarkable applications of laser-plasma interaction as intense source of RF-microwaves for studies on materials and devices, EMP-radiation-hardening and electromagnetic compatibility. The demonstrated extreme effectivity of electric-fields detection in laser-plasma context by electro-optic effect, leads to great potential for characterization of laser-plasma interaction and generated Terahertz radiation.

  11. Impact of severe cracked germanium (111 substrate on aluminum indium gallium phosphate light-emitting-diode’s electro-optical performance

    Directory of Open Access Journals (Sweden)

    Annaniah Luruthudass

    2016-01-01

    Full Text Available Cracked die is a serious failure mode in the Light Emitting Diode (LED industry – affecting LED quality and long-term reliability performance. In this paper an investigation has been carried out to find the correlation between severe cracked germanium (Ge substrate of an aluminum indium gallium phosphate (AlInGaP LED and its electro-optical performance after the Temperature Cycle (TC test. The LED dice were indented at several bond forces using a die bonder. The indented dice were analysed using a Scanning Electron Microscope (SEM. The result showed that severe cracks were observed at 180 gF onward. As the force of indentation increases, crack formation also becomes more severe thus resulting in the chipping of the substrate. The cracked dies were packaged and the TC test was performed. The results did not show any electro-optical failure or degradation, even after a 1000 cycle TC test. Several mechanically cross-sectioned cracked die LEDs, were analysed using SEM and found that no crack reached the active layer. This shows that severely cracked Ge substrate are able to withstand a −40°C/+100°C TC test up to 1000 cycles and LED optical performance is not affected. A small leakage current was observed in all of the cracked die LEDs in comparison to the reference unit. However, this value is smaller than the product specification and is of no concern.

  12. 40 Gb/s Microstrip Line Polymer Electro-Optic Modulators%40Gb/s微带线电极聚合物电光调制器

    Institute of Scientific and Technical Information of China (English)

    白一鸣; 曲欣; 王晓林; 王士杰; 吴伯瑜

    2011-01-01

    40 Gb/s polymer electro-optic modulators with microstrip line traveling-wave electrode are designed, fabricated and tested. Assuming that the electro-optic coefficient γ33 of the core polymer is 30 pm/V, the performance parameters of the designed modulator are half-wave voltage Vx = 4. 94 V and modulation bandwidth 42 GHz. The modulator is fabricated using the second-order nonlinear optical polymer material BPAN-NT with a completely independent intellectual property as the core layer material of the polymer electro-optic modulator. After that, the performances of the modulators in direct current (DC), low frequencies and microwave regions are tested. The low-frequency (237 Hz) Vx values at 1. 31 and 1. 55 μm wavelengths are 32. 1 and 40. 5 V, respectively. The electro-optic coefficient of core layer material γ33 is thus obtained as 3.856 pm/V. The extinction ratio is measured to be 20 dB. Within the frequencies ranging from 50 MHz to 40 GHz, the actual measured microwave attenuation coefficient ao of the electrode system is 0. 6 dB·cm-1 ·GHz-1/2, Using this value, the modulation bandwidth of the modulator is calculated to be 42.70 GHz. The modulation indices are measured by using optical spectrum analyzer in the frequency range from 7.5 to 16 GHz and from 32 to 40 GHz. And the frequency response curve of the modulation index M of the electro-optic polymer modulator is also obtained. The 3 dB bandwidth of the 40 Gb/s modulator is 30 GHz.%设计、制作和测试了用于1.31和1.55 μm光波长的40 Gb/s微带线行波电极的电光调制器.假设聚合物材料的电光系数γ33=30 pm/V,设计的调制器性能参数分别是半波电压Vπ=4.92 V和调制带宽42 GHz.用有完全自主知识产权的二阶非线性光学聚合物材料BPAN-NT作为芯层材料制作了聚合物电光调制器.对调制器的各项特性参数进行了直流、低频和微波的测试,在1.31和1.55 μm波长上测得低频(237 Hz)Vπ分别为32.1和40.5 V,折算得

  13. Performance management in the Slovak higher education system: preliminary evaluation

    Directory of Open Access Journals (Sweden)

    Juraj Nemec

    2007-10-01

    Full Text Available The aim of our paper is a preliminary evaluation of the introduction of performance management and performance financing arrangements in the Slovak higher education system – accreditation and formula based performance financing. This evaluation will be mainly based on the assessment of short-term impacts of the above mentioned instruments and is expected to invite further professional discussion. We feel that the data and brief analysis included are sufficient enough to show that the Slovak system represents a typical example of the potential of performance management and performance financing being significantly limited, if not destroyed. Not only because of improperly defined indicators, which are too much input and quantity orientated, but very much also due to a lack of resources (the ratio of public expenditures for higher education to the GDP in Slovakia is significantly below EU average, as well as the politicization of the system.

  14. New Crystalline Materials for Nonlinear Frequency Conversion, Electro-Optic Modulation, and Mid-Infrared Gain Media

    Energy Technology Data Exchange (ETDEWEB)

    Adams, J

    2002-08-09

    New crystalline materials were investigated for applications in frequency conversion of near-infrared wavelengths and as gain media for tunable mid-infrared solid-state lasers. GaCa{sub 4}O(BO{sub 3}){sub 3} (GdCOB), YCa{sub 4}O(BO{sub 3}){sub 3} (YCOB), LaCa{sub 4}O(BO{sub 3}){sub 3} (LaCOB), and Gd{sub 0.275}Y{sub 0.725}Ca{sub 4}O(BO{sub 3}){sub 3} were characterized for frequency conversion of 1 {micro}m lasers. For type I doubling at 1064 nm, LaCOB, GdCOB, and YCOB were found to have effective coupling coefficients (d{sub eff}) of 0.52 {+-} 0.05, 0.78 {+-} 0.06, and 1.12 {+-} 0.07 pm/V, respectively. LaCOB was measured to have angular and thermal sensitivities of 1224 {+-} 184 (cm-rad){sup -1} and < 0.10 (cm-{sup o}C){sup -1}, respectively. The effective coupling coefficient for type II noncritically phasematched (NCPM) doubling at 1064 nm in Gd{sub 0.275}Y{sub 0.725}Ca{sub 4}O(BO{sub 3}){sub 3} was measured to be 0.37 {+-} 0.04 pm/V. We predict LaCOB to have a type I NCPM fundamental wavelength of 1042 {+-} 1.5 nm. Due to its low angular and thermal sensitivities for doubling near 1047 nm, LaCOB has potential for frequency doubling of high-average power Nd:LiYF{sub 4} and Yb:Sr{sub 5}(P0{sub 4}){sub 3}F lasers. LaCOB, GdCOB, and YCOB were also investigated for optical parametric oscillator applications and we determined that they may have potential in a Ti:sapphire pumped oscillator. The effective linear electro-optic coefficients (r{sub eff}) were measured along dielectric directions in YCOB and a maximum r{sub eff} of 10.8 pm/V was found. For a crystal with a 5:1 aspect ratio, the corresponding half-wave voltage at 1064 nm would be 19.6 kV. Therefore a Pockels cell composed of two YCOB crystals with 5:1 aspect ratios would have a required half-wave voltage <10 kV. Moderate coupling coefficients (3 x KH{sub 2}PO{sub 4}), low thermal sensitivities, ease of growth to large sizes, non-hygroscopicity, and favorable polishing and coating characteristics make La

  15. Land cover classification accuracy from electro-optical, X, C, and L-band Synthetic Aperture Radar data fusion

    Science.gov (United States)

    Hammann, Mark Gregory

    The fusion of electro-optical (EO) multi-spectral satellite imagery with Synthetic Aperture Radar (SAR) data was explored with the working hypothesis that the addition of multi-band SAR will increase the land-cover (LC) classification accuracy compared to EO alone. Three satellite sources for SAR imagery were used: X-band from TerraSAR-X, C-band from RADARSAT-2, and L-band from PALSAR. Images from the RapidEye satellites were the source of the EO imagery. Imagery from the GeoEye-1 and WorldView-2 satellites aided the selection of ground truth. Three study areas were chosen: Wad Medani, Sudan; Campinas, Brazil; and Fresno- Kings Counties, USA. EO imagery were radiometrically calibrated, atmospherically compensated, orthorectifed, co-registered, and clipped to a common area of interest (AOI). SAR imagery were radiometrically calibrated, and geometrically corrected for terrain and incidence angle by converting to ground range and Sigma Naught (?0). The original SAR HH data were included in the fused image stack after despeckling with a 3x3 Enhanced Lee filter. The variance and Gray-Level-Co-occurrence Matrix (GLCM) texture measures of contrast, entropy, and correlation were derived from the non-despeckled SAR HH bands. Data fusion was done with layer stacking and all data were resampled to a common spatial resolution. The Support Vector Machine (SVM) decision rule was used for the supervised classifications. Similar LC classes were identified and tested for each study area. For Wad Medani, nine classes were tested: low and medium intensity urban, sparse forest, water, barren ground, and four agriculture classes (fallow, bare agricultural ground, green crops, and orchards). For Campinas, Brazil, five generic classes were tested: urban, agriculture, forest, water, and barren ground. For the Fresno-Kings Counties location 11 classes were studied: three generic classes (urban, water, barren land), and eight specific crops. In all cases the addition of SAR to EO resulted

  16. Electro-optical evaluation of tungsten oxide and vanadium pentoxide thin films for modeling an electrochromic device

    Directory of Open Access Journals (Sweden)

    H Najafi Ashtiani

    2015-01-01

    Full Text Available In this study, tungsten oxide and vanadium oxide electrochromic thin films were placed in vacuum and in a thickness of 200 nm on a transparent conductive substrate of SnO2:F using the physical method of thermal evaporation. Then they were studied for the optical characteristics in the wavelength range from 400 to 700 nm and for their electrical potentials in the range form +1.5 to -1.5 volts. The films were post heated in order to assess changes in energy gap with temperature, at temperatures120 , 300 and 500°C. Refractive and extinction coefficients and the transition type of films in the visible light range and in the thickness of 200 nm were determined and measured. X-ray diffraction pattern and SEM images and cyclic Voltammetry of layers were also studied. The results of this study due to the deposition of layers, the layer thickness selected, the type of substrate, the range of annealing temperatures and selected electrolyte were in full compliance with the works of other researchers [1,2,3]. Therefore, these layers with features such as crystal structure, refractive and even extinction coefficients in the range of visible light, the appropriate response of chromic switch in the replication potential, good adhesion to the substrate, and the high amount of optical transmition and so on, prove useful to be used in an electrochromic device

  17. Electro-optic Effects in Special Asymmetric Quantum Wells%一种特殊的非对称量子阱中的电光效应

    Institute of Scientific and Technical Information of China (English)

    俞友宾; 郭康贤; 于凤梅

    2004-01-01

    Recently, there has been an increasing interest in nonlinear optical properties of semiconductor quantum well structures, because of their relevance for studying practical applications and as a probe for the electronic structure of mesoscopic media. In this paper, the nonlinear electro-optic effects in special asymmetric quantum wells are studied. Because of this kind of quantum well is more approximate a practical quantum well between the conduction band and valence band, and it can be realized very easily in experiment. The analytical expressions of electro-optic coefficient have been derived by compact density-matrix approach and the numerical results were presented for GaAs/AlGaAs asymmetric quantum wells. The shape of the quantum well varying with the parameter a and the parameter V0 were plotted. Itis found that the asyrmnetry of the quantum wells enhances with the increase of parameter a. On the contrary, the asymmetry of the quantum walls decreases with the increase of the parameter Vo. The maximum values of the electro-optic coefficient varying with the parameter a and the parameter V0 were plotted. The numerical results show the electro-optic coefficient enhances with the increases of the parameter a and the decrease of the parameter V0. Therefore, it is found that the electro-optic coefficient increases with the enhancement of the quantum wells' asymmetry. The electro-optic coefficient as afunction of the photon energy with different values of parameter a and different values of parameter V0 were also plotted. It can be observed that there are three peak values in the figures, respectively. And it is obvious that the larger the asymmetry of quantum wells is, the bigger the peak value is. It can be seen that with the increase of the asymmetry of quantum well, the peaks move to the low energy side.Moreover, the electro-optic coefficient obtained in this special quantum well is as large as 104 m/V.With the advances of nanofabrication technology recently, it

  18. Preliminary safety evaluation for the plutonium stabilization and packaging system

    Energy Technology Data Exchange (ETDEWEB)

    Shapley, J.E., Fluor Daniel Hanford

    1997-03-14

    This Preliminary Safety Evaluation (PSE) describes and analyzes the installation and operation of the Plutonium Stabilization and Packaging System (SPS) at the Plutonium Finishing Plant (PFP). The SPS is a combination of components required to expedite the safe and timely storage of Plutonium (Pu) oxide. The SPS program will receive site Pu packages, process the Pu for storage, package the Pu into metallic containers, and safely store the containers in a specially modified storage vault. The location of the SPS will be in the 2736- ZB building and the storage vaults will be in the 2736-Z building of the PFP, as shown in Figure 1-1. The SPS will produce storage canisters that are larger than those currently used for Pu storage at the PFP. Therefore, the existing storage areas within the PFP secure vaults will require modification. Other modifications will be performed on the 2736-ZB building complex to facilitate the installation and operation of the SPS.

  19. A Serious Games Platform for Cognitive Rehabilitation with Preliminary Evaluation.

    Science.gov (United States)

    Rego, Paula Alexandra; Rocha, Rui; Faria, Brígida Mónica; Reis, Luís Paulo; Moreira, Pedro Miguel

    2017-01-01

    In recent years Serious Games have evolved substantially, solving problems in diverse areas. In particular, in Cognitive Rehabilitation, Serious Games assume a relevant role. Traditional cognitive therapies are often considered repetitive and discouraging for patients and Serious Games can be used to create more dynamic rehabilitation processes, holding patients' attention throughout the process and motivating them during their road to recovery. This paper reviews Serious Games and user interfaces in rehabilitation area and details a Serious Games platform for Cognitive Rehabilitation that includes a set of features such as: natural and multimodal user interfaces and social features (competition, collaboration, and handicapping) which can contribute to augment the motivation of patients during the rehabilitation process. The web platform was tested with healthy subjects. Results of this preliminary evaluation show the motivation and the interest of the participants by playing the games.

  20. Preliminary Evaluation of Removing Used Nuclear Fuel from Shutdown Sites

    Energy Technology Data Exchange (ETDEWEB)

    Maheras, Steven J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Best, Ralph E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Ross, Steven B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Buxton, Kenneth A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); England, Jeffery L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); McConnell, Paul E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Massaro, Lawrence M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jensen, Philip J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-09-30

    A preliminary evaluation of removing spent nuclear fuel (SNF) from 13 shutdown nuclear power reactor sites was conducted. At these shutdown sites the nuclear power reactors have been permanently shut down and the sites have been decommissioned or are undergoing decommissioning. The shutdown sites were Maine Yankee, Yankee Rowe, Connecticut Yankee, Humboldt Bay, Big Rock Point, Rancho Seco, Trojan, La Crosse, Zion, Crystal River, Kewaunee, San Onofre, and Vermont Yankee. The evaluation was divided into four components: (1) characterization of the SNF and greater-than-Class C low-level radioactive waste (GTCC waste) inventory, (2) a description of the on-site infrastructure and conditions relevant to transportation of SNF and GTCC waste, (3) an evaluation of the near-site transportation infrastructure and experience relevant to shipping transportation casks containing SNF and GTCC waste, including identification of gaps in information, and (4) an evaluation of the actions necessary to prepare for and remove SNF and GTCC waste. Every site was found to have at least one off-site transportation mode option for removing its SNF and GTCC waste; some have multiple options. Experience removing large components during reactor decommissioning provided an important source of information used to identify the transportation mode options for the sites. Especially important in conducting the evaluation were site visits, through which information was obtained that would not have been available otherwise. Extensive photographs taken during the site visits proved to be particularly useful in documenting the current conditions at or near the sites. It is expected that additional site visits will be conducted to add to the information presented in the evaluation.

  1. A Diode-Stack End-Pumped Electro-Optically Q-Switched Nd:YAG Slab Oscillator-Amplifier System

    Institute of Scientific and Technical Information of China (English)

    ZHANG Heng-Li; YAN Ying; LI Dai-Jun; SHI Peng; DU Ke-Ming

    2008-01-01

    A laser diode-stack end-pumped electro-optically Q-switched Nd:YAG slab oscillator-amplifier system with near-diffraction-limited output is demonstrated by a stable-unstable hybrid resonator. The average power of 100 W at a repetition rate or 10kHz with a pulse width 14.7ns and average power of 76.3 W at a repetition rate of 5kHz with a pulse width of 10.2ns are measured. At the repetition rate of 10 kHz and at an output power of 89 W, the beam quality factors M2 in the unstable and stable directions are 1.3 and 1.5, respectively.

  2. Free space millimeter wave-coupled electro-optic high speed nonlinear polymer phase modulator with in-plane slotted patch antennas.

    Science.gov (United States)

    Park, D H; Pagán, V R; Murphy, T E; Luo, J; Jen, A K-Y; Herman, W N

    2015-04-06

    We report in-plane slotted patch antenna-coupled electro-optic phase modulators with a carrier-to-sideband ratio (CSR) of 22 dB under an RF power density of 120 W/m(2) and a figure of merit of 2.0 W(-1/2) at the millimeter wave frequencies of 36-37 GHz based on guest-host type of second-order nonlinear polymer SEO125. CSR was improved more than 20 dB by using a SiO(2) protection layer. We demonstrate detection of 3 GHz modulation of the RF carrier. We also derive closed-form expressions for the modulated phase of optical wave and carrier-to-sideband ratio. Design, simulation, fabrication, and experimental results are discussed.

  3. Narrow linewidth comb realized with a mode-locked fiber laser using an intra-cavity waveguide electro-optic modulator for high-speed control.

    Science.gov (United States)

    Iwakuni, Kana; Inaba, Hajime; Nakajima, Yoshiaki; Kobayashi, Takumi; Hosaka, Kazumoto; Onae, Atsushi; Hong, Feng-Lei

    2012-06-18

    We have developed an optical frequency comb using a mode-locked fiber ring laser with an intra-cavity waveguide electro-optic modulator controlling the optical length in the laser cavity. The mode-locking is achieved with a simple ring configuration and a nonlinear polarization rotation mechanism. The beat note between the laser and a reference laser and the carrier envelope offset frequency of the comb were simultaneously phase locked with servo bandwidths of 1.3 MHz and 900 kHz, respectively. We observed an out-of-loop beat between two identical combs, and obtained a coherent δ-function peak with a signal to noise ratio of 70 dB/Hz.

  4. Thermo-optic characterization of KDP single crystals by a modified Sénarmont setup for electro-optic modulation system

    Institute of Scientific and Technical Information of China (English)

    H. L. Saadon; M. A. Rahma; Ali F. Marhoon; N. Théofanous; M. Aillerie

    2009-01-01

    For our KDP crystal orientation, various thermo-optic (TO) and relevant temperature-dependence param-eters are defined, presented, and studied in the framework of a transverse and a longitudinal electro-optic (EO) modulation systems. This study is based on the concept of the so-called opto-electrical bias (ψ) ap-plied to the system. For both of the above EO-modulation systems, a set of original equations is extracted and investigated with regard to each of the more important TO or temperature coefficients. Using these equations, for these parameters the role of the transverse configuration is examined in comparison with its corresponding longitudinal configuration. A comparison is done with other orientation of the same KDP crystal.

  5. 电光调制器驱动源电路研究%Research of electro-optic modulator circuit of the driving source

    Institute of Scientific and Technical Information of China (English)

    谭丰菊; 张志伟

    2011-01-01

    High-speed optical fiber communication systems are usually driven by external modulation circuit, the external modulation drive circuit must be able to provide sufficient output drive voltage and DC bias to meet the needs of the modulator. Based on the above purpose, it researched the circuit design of the source of electro-optic modulator driver.%高速光纤通信系统中通常采用外调制驱动电路,外调制驱动电路必须能够提供足够的输出驱动电压和直流偏压以满足调制器的需要.基于上述目的,研究了电光调制器的驱动源电路设计.

  6. Structure and microwave properties analysis of substrate removed GaAs/AIGaAs electro-optic modulator structure by finite element method

    Institute of Scientific and Technical Information of China (English)

    Kambiz ABEDI; Habib VAHIDI

    2013-01-01

    In this paper, structure and microwave properties of a substrate removed GaAs/A1GaAs traveling wave electro-optic modulator structure were analyzed and simulated by using the finite element numerical technique for lower loss, simultaneous matching of optical and microwave velocities and impedance matching with 50 Ω. The effects of core layer thickness, claddings thicknesses, and width of the modulator on the microwave effective index nm were investigated, the characteristic impedance Zc, the microwave losses a, and the half-wave voltage- length product VmL were calculated. The results of the simulation suggest that the electrical bandwidth of 22 GHz and the optical bandwidth of 48 GHz can be obtained for fully matched, lower loss structure, which correspond to a 13 V. cm drive voltage.

  7. Laser frequency locking with 46 GHz offset using an electro-optic modulator for magneto-optical trapping of francium atoms

    CERN Document Server

    Harada, K; Ezure, S; Kato, K; Hayamizu, T; Kawamura, H; Inoue, T; Arikawa, H; Ishikawa, T; Aoki, T; Uchiyama, A; Sakamoto, K; Ito, S; Itoh, M; Ando, S; Hatakeyama, A; Hatanaka, K; Imai, K; Murakami, T; Nataraj, H S; Shimizu, Y; Sato, T; Wakasa, T; Yoshida, H P; Sakemi, Y

    2016-01-01

    We demonstrated a frequency offset locking between two laser sources using a waveguide-type electro-optic modulator (EOM) with 10th-order sidebands for magneto-optical trapping of Fr atoms. The frequency locking error signal was successfully obtained by performing delayed self-homodyne detection of the beat signal between the repumping frequency and the 10th-order sideband component of the trapping light. Sweeping the trapping-light and repumping-light frequencies with keeping its frequency difference of 46 GHz was confirmed over 1 GHz by monitoring the Doppler absorption profile of I2. This technique enables us to search for a resonance frequency of magneto-optical trapping of Fr.

  8. Wannier-Stark electro-optical effect, quasi-guided and photonic modes in 2D macroporous silicon structures with SiO2 coatings

    Science.gov (United States)

    Karachevtseva, L.; Goltviansky, Yu.; Sapelnikova, O.; Lytvynenko, O.; Stronska, O.; Bo, Wang; Kartel, M.

    2016-12-01

    Opportunities to enhance the properties of structured surfaces were demonstrated on 2D macroporous silicon structures with SiO2 coatings. We investigated the IR light absorption oscillations in macroporous silicon structures with SiO2 coatings 0-800 nm thick. The Wannier-Stark electro-optical effect due to strong electric field on Si-SiO2boundary and an additional electric field of quasi-guided optical modes were taken into account. The photonic modes and band gaps were also considered as peculiarities in absorbance spectra of macroporous silicon structures with a thick SiO2 coating. The photonic modes do not coincide with the quasi-guided modes in the silicon matrix and do not appear in absorption spectra of 2D macroporous silicon structures with surface nanocrystals.

  9. Demonstration of a near-IR line-referenced electro-optical laser frequency comb for precision radial velocity measurements in astronomy.

    Science.gov (United States)

    Yi, X; Vahala, K; Li, J; Diddams, S; Ycas, G; Plavchan, P; Leifer, S; Sandhu, J; Vasisht, G; Chen, P; Gao, P; Gagne, J; Furlan, E; Bottom, M; Martin, E C; Fitzgerald, M P; Doppmann, G; Beichman, C

    2016-01-27

    An important technique for discovering and characterizing planets beyond our solar system relies upon measurement of weak Doppler shifts in the spectra of host stars induced by the influence of orbiting planets. A recent advance has been the introduction of optical frequency combs as frequency references. Frequency combs produce a series of equally spaced reference frequencies and they offer extreme accuracy and spectral grasp that can potentially revolutionize exoplanet detection. Here we demonstrate a laser frequency comb using an alternate comb generation method based on electro-optical modulation, with the comb centre wavelength stabilized to a molecular or atomic reference. In contrast to mode-locked combs, the line spacing is readily resolvable using typical astronomical grating spectrographs. Built using commercial off-the-shelf components, the instrument is relatively simple and reliable. Proof of concept experiments operated at near-infrared wavelengths were carried out at the NASA Infrared Telescope Facility and the Keck-II telescope.

  10. Electronic structure and electro-optical properties of ion radicals formed during the reduction of N, N'-dialkylsubstituted salts of 4,4'-bipyridyl

    Science.gov (United States)

    Zakirov, M. I.; Efimov, N. N.; Mel'nikov, P. V.; Nodova, E. L.; Minin, V. V.

    2013-08-01

    Symmetric N, N'-disubstituted salts of 4,4'-bipyridyl (viologens) are synthesized and described. It is shown by cyclic voltammetry that disubstituted salts of 4,4'-bipyridyl have a tendency toward reversible two-electron reduction. Normal first and second step oxidation-reduction potentials with respect to saturated silver chloride electrodes at various potential scan rates are found. The spectra of the high-resolution electron paramagnetic resonance of viologen cation radicals formed during the reduction of N, N'-disubstituted salts of 4,4'-bipyridyl are obtained and interpreted. It is established that the nature of substitutes and counterions in a viologen molecule considerably influences the distribution of its spin density, voltammetric curves, and electro-optical properties.

  11. Design of CMOS compatible and compact, thermally-compensated electro-optic modulator based on off-axis microring resonator for dense wavelength division multiplexing applications.

    Science.gov (United States)

    Haldar, Raktim; Banik, Abhik D; Varshney, Shailendra K

    2014-09-22

    In this work, we propose and demonstrate the performance of silicon-on-insulator (SOI) off-axis microring resonator (MRR) as electro-optic modulator (EOM). Adding an extra off-axis inner-ring in conventional microring structure provides control to compensate thermal effects on EOM. It is shown that dynamically controlled bias-voltage applied to the outer ring has the potency to quell the thermal effects over a wide range of temperature. Thus, besides the appositely biased conventional microring, off-axis inner microring with pre-emphasized electrical input message signal enables our proposed structure suitable for high data-rate dense wavelength division multiplexing scheme of optical communication within a very compact device size.

  12. Novel RF Interrogation of a Fiber Bragg Grating Sensor Using Bidirectional Modulation of a Mach-Zehnder Electro-Optical Modulator

    Science.gov (United States)

    Choi, Sang-Jin; Mao, Wankai; Pan, Jae-Kyung

    2013-01-01

    We propose and experimentally demonstrate the novel radio-frequency (RF) interrogation of a fiber Bragg grating (FBG) sensor using bidirectional modulation of a Mach-Zehnder electro-optical modulator (MZ-EOM). Based on the microwave photonic technique and active detection, the transfer function of the proposed system was obtained, and the time delay was calculated from the change in the free spectral range (FSR) at different wavelengths over the optimal measuring range. The results show that the time delay and the wavelength variation have a good linear relationship, with a gradient of 9.31 ps/nm. An actual measurement taken with a sensing FBG for temperature variation shows the relationship with a gradient of 0.93 ps/10 °C. The developed system could be used for FBG temperature or strain sensing and other multiplexed sensor applications. PMID:23820744

  13. 10 kHz ps 1342 nm laser generation by an electro-optically cavity-dumped mode-locked Nd:YVO4 laser

    Science.gov (United States)

    Chen, Ying; Liu, Ke; He, Li-jiao; Yang, Jing; Zong, Nan; Yang, Feng; Gao, Hong-wei; Liu, Zhao; Yuan, Lei; Lan, Ying-jie; Bo, Yong; Peng, Qin-jun; Cui, Da-fu; Xu, Zu-yan

    2017-01-01

    We have demonstrated an electro-optically cavity-dumped mode-locked (CDML) picosecond Nd:YVO4 laser at 1342 nm with 880 nm diode-laser direct pumping. At a repetition rate of 10 kHz, an average output power of 0.119 W was achieved, corresponding to a pulse energy of 11.9 μJ. Compared with the continuous wave mode-locking pulse energy of 17.5 nJ, the CDML pulse energy was 680 times higher. The pulse width was measured to be 33.4 ps, resulting in the peak power of 356 kW. Meanwhile, the beam quality was nearly diffraction limited with an average beam quality factor M2 of 1.29.

  14. Investigation of the Effect of Yttrium Oxide Nanoparticles Doped with Cerium and Neodymium on Electro-Optics of Liquid Crystal Polymer Composites

    Science.gov (United States)

    Zharkova, G. M.; Osipov, V. V.; Platonov, V. V.; Podkin, A. V.; Strel'tsov, S. A.

    2016-12-01

    Morphology and properties of liquid crystal polymer composites doped with inorganic nanoparticles are described. These composites comprised nematic liquid crystal 5CB, polyvinyl acetate, and nanoparticles of oxides (Y2O3, CeO2:Y2O3, and Nd2O3:Y2O3). Nanopowders were synthesized by the laser method of vaporization of a solid target under CO2-laser or fiber ytterbium laser irradiation. The effect of oxides on the electro-optical properties of the composites and times of response to an electrical pulse is investigated. It is shown that incorporation of CeO2:Y2O3 nanopowder in liquid crystal polymer composites affects the decrease of the control field and the increase of light transmission in an electric field stronger than incorporation of Nd2O3:Y2O3 nanoparticles.

  15. Experimental and numeric studies of one electro-optical flexible pipe (umbilical); Estudos numericos e experimentais de um umbilical eletro-optico

    Energy Technology Data Exchange (ETDEWEB)

    Lepore, Paula Ferreira; Buelta Martinez, Miguel Angel [Sao Paulo Univ., SP (Brazil). Escola Politecnica

    2005-07-01

    This work had as objective to develop, to implant, to survey and to test an experimental and numerical model of structural, applicable analysis of umbilical structures. An ample study of the behavior of its constituent layers was carried through, in special of its nucleus and material constituents, when operating under different conditions of tensions and deformations. As support for this work, experimental tests for one type of electro-optic umbilical with typical transversal section had been carried through. This was made with the intention to optimize the developed numerical model. With this model of structural analysis, the project of umbilicals could highly improved, in terms of the total weight of the handle, which is one of the great problems for its use in great depths, with the maximum of efficiency and the minimum of losses, foreseeing and hindering operation imperfections that can come to occur due to extreme deformation or electric rupture of the layers, hoses or handles. (author)

  16. Electro-optical response of polymer-dispersed liquid crystal single layers of large nematic droplets oriented by rubbed teflon nanolayers

    Science.gov (United States)

    Marinov, Y. G.; Hadjichristov, G. B.; Petrov, A. G.; Marino, S.; Versace, C.; Scaramuzza, N.

    2013-02-01

    The surface orienting effect of rubbed teflon nanolayers on the morphology and electro-optical (EO) response of polymer-dispersed liquid crystal (PDLC) single layers of large nematic droplets was studied experimentally. In PDLC composites of the nematic liquid crystal (LC) E7 and NOA65 polymer, single droplets of LC with diameters as larger as 10 μm were confined in layers with a thickness of 10 μm, and the nematic director field was efficiently modified by nanostructuring teflon rubbing of the glass plates of the PDLC cell. For layered PDLCs arranged and oriented in this way, the modulated EO response by the dielectric oscillations of the nematic director exhibits a selective amplitude-frequency modulation controllable by both temperature and voltage applied, and is simply related to the LC droplet size. That may be of practical interest for PDLC-based modulators operating in the infrasound frequency range.

  17. Enhanced conductivity of sol-gel silica cladding for efficient poling in electro-optic polymer/TiO2 vertical slot waveguide modulators.

    Science.gov (United States)

    Enami, Yasufumi; Jouane, Youssef; Luo, Jingdong; Jen, Alex K-Y

    2014-12-01

    We report the enhanced conductivity of sol-gel silica under-cladding for efficient poling of electro-optic (EO) polymer in a hybrid EO polymer/TiO2 vertical slot waveguide modulator. The electrical volume conductivity of sol-gel silica cladding increases approximately 30 times when the calcining time of the cladding layer is critically reduced to 45 minutes, which increases the in-device EO coefficient of the 600-nm-thick EO polymer film in modulators and reduces the lower halfwave voltage (Vπ) of the modulators. The lowest driving voltage (Vπ) of the TiO2 slot waveguide modulator is 2.0 V for an electrode length (Le) of 10 mm and wavelength of 1550 nm (VπLe = 2.0 V·cm) for the low-index guest-host EO polymer SEO125. The optical propagation loss is reduced to 7 dB/cm.

  18. An atomic spin precession detection method based on electro-optic modulation in an all-optical K-Rb hybrid atomic magnetometer

    Science.gov (United States)

    Hu, Yanhui; Liu, Xuejing; Li, Yang; Yao, Han; Dai, Lingling; Yang, Biyao; Ding, Ming

    2017-07-01

    We present an ultrahigh-sensitivity electro-optic modulator (EOM) detection method for detecting the atomic Larmor precession in an all-optical K-Rb hybrid atomic magnetometer operating in the spin-exchange relaxation-free regime. A magnetic field sensitivity of ~10 f T Hz-1/2 has been achieved by optimizing the probe laser parameters and the EOM modulation conditions, which is comparable to that with the Faraday modulation method and has a better performance than the balanced polarimetry method in the low frequency range. The EOM detection method in the atomic magnetometer presents several advantages, such as simple structure, no extra magnetic noise, moderate thermal effect, high measurement sensitivity and reliable stability. It is demonstrated to be feasible for the improved compactness and simplicity of atomic magnetic field measurement devices in the future.

  19. Signal transmission in a human body medium-based body sensor network using a Mach-Zehnder electro-optical sensor.

    Science.gov (United States)

    Song, Yong; Hao, Qun; Zhang, Kai; Wang, Jingwen; Jin, Xuefeng; Sun, He

    2012-11-30

    The signal transmission technology based on the human body medium offers significant advantages in Body Sensor Networks (BSNs) used for healthcare and the other related fields. In previous works we have proposed a novel signal transmission method based on the human body medium using a Mach-Zehnder electro-optical (EO) sensor. In this paper, we present a signal transmission system based on the proposed method, which consists of a transmitter, a Mach-Zehnder EO sensor and a corresponding receiving circuit. Meanwhile, in order to verify the frequency response properties and determine the suitable parameters of the developed system, in-vivo measurements have been implemented under conditions of different carrier frequencies, baseband frequencies and signal transmission paths. Results indicate that the proposed system will help to achieve reliable and high speed signal transmission of BSN based on the human body medium.

  20. Signal Transmission in a Human Body Medium-Based Body Sensor Network Using a Mach-Zehnder Electro-Optical Sensor

    Directory of Open Access Journals (Sweden)

    Yong Song

    2012-11-01

    Full Text Available The signal transmission technology based on the human body medium offers significant advantages in Body Sensor Networks (BSNs used for healthcare and the other related fields. In previous works we have proposed a novel signal transmission method based on the human body medium using a Mach-Zehnder electro-optical (EO sensor. In this paper, we present a signal transmission system based on the proposed method, which consists of a transmitter, a Mach-Zehnder EO sensor and a corresponding receiving circuit. Meanwhile, in order to verify the frequency response properties and determine the suitable parameters of the developed system, in-vivo measurements have been implemented under conditions of different carrier frequencies, baseband frequencies and signal transmission paths. Results indicate that the proposed system will help to achieve reliable and high speed signal transmission of BSN based on the human body medium.

  1. Novel RF Interrogation of a Fiber Bragg Grating Sensor Using Bidirectional Modulation of a Mach-Zehnder Electro-Optical Modulator

    Directory of Open Access Journals (Sweden)

    Jae-Kyung Pan

    2013-07-01

    Full Text Available We propose and experimentally demonstrate the novel radio-frequency (RF interrogation of a fiber Bragg grating (FBG sensor using bidirectional modulation of a Mach-Zehnder electro-optical modulator (MZ-EOM. Based on the microwave photonic technique and active detection, the transfer function of the proposed system was obtained, and the time delay was calculated from the change in the free spectral range (FSR at different wavelengths over the optimal measuring range. The results show that the time delay and the wavelength variation have a good linear relationship, with a gradient of 9.31 ps/nm. An actual measurement taken with a sensing FBG for temperature variation shows the relationship with a gradient of 0.93 ps/10 °C. The developed system could be used for FBG temperature or strain sensing and other multiplexed sensor applications.

  2. Integrated quasi-phase-matched second-harmonic generator and electro-optic phase modulator for low-noise phase-sensitive amplification.

    Science.gov (United States)

    Enbutsu, Koji; Umeki, Takeshi; Tadanaga, Osamu; Asobe, Masaki; Takenouchi, Hirokazu

    2015-07-15

    We propose a quasi-phase-matched second-harmonic generator integrated with an electro-optic phase modulator in a directly bonded LiNbO3 (DB-LN) waveguide to obtain high signal-to-noise ratio (SNR) pump light for a phase-sensitive amplifier (PSA). This integrated device exhibits 1-MHz modulation and 1-W second-harmonic-generation properties sufficient for phase-locking between the signal and pump and for PSA gain, respectively. A novel PSA configuration based on the high-input-power tolerance of the device helps to suppress the noise from the erbium-doped fiber amplifier used for pump-light generation and leads to an improvement of the SNR of the pump light. The SNR improvement was confirmed by comparing the noise figure of a PSA employing the DB-LN waveguide with that of a PSA using a Ti-diffused LN waveguide modulator.

  3. Electro-optic coefficients r13 and r33 of singly Er3+-doped and In3+/Er3+-codoped LiNbO3 crystals

    Science.gov (United States)

    Du, Wan-Ying; Zhang, Pei; Zhang, Zi-Bo; Ren, Shuai; Wong, Wing-Han; Yu, Dao-Yin; Pun, Edwin Yue-Bun; Zhang, De-Long

    2017-01-01

    A series of singly Er3+-doped and doubly In3+/Er3+-doped congruent LiNbO3 crystals were grown by Czochralski method. The Er3+-only doped crystals were grown from the growth melts doped with different concentrations of Er2O3 up to 1 mol%, and the In3+/Er3+-codoped crystals from the melts doped with fixed 0.5 mol% Er2O3 while varied In2O3 contents of 0.0, 0.5, 1.0 and 1.5 mol%. The electro-optic coefficients γ13 and γ33 of these doped crystals were measured by Mach-Zehnder interferometry. Both clamped and unclamped coefficients were measured. The results show that both γ13 and γ33 reveal small Er3+ and In3+ doping effects. In the Er3+-only doping case, γ13 almost does not change within the experimental error of 3%, γ33 reveals a degradation tendency with a rise in Er3+ doping level, but the degradation is no more than 5% in the considered Er3+ concentration range 0-3.0 mol% (in crystal). In the In3+/Er3+-codoping case, both γ13 and γ33 can be regarded as unchanged in the studied In3+ concentration range of 0-2.6 mol% (in crystal) within the error. The small Er3+ or In3+ doping effect is desired in light of electro-optic application of these crystals. It is qualitatively explained on the basis of EO coefficient model and doping effect on defect structure of LiNbO3.

  4. Femtosecond writing of near-surface waveguides in lithium niobate for low-loss electro-optical modulators of broadband emission

    Science.gov (United States)

    Bukharin, Mikhail A.; Skryabin, Nikolay N.; Khudyakov, Dmitriy V.; Vartapetov, Sergey K.

    2016-05-01

    In the investigation we demonstrated technique of direct femtosecond laser writing of tracks with induced refractive index at record low depth under surface of lithium niobate (3-15 μm). It was shown that with the help of proposed technique one can be written claddings of near surface optical waveguides that plays a key role in fabrication of fast electro-optical modulators with low operating voltage. Fundamental problem resolved in the investigation consists in suppression of negative factors impeding femtosecond inscription of waveguides at low depths. To prevent optical breakdown of crystal surface we used high numerical aperture objectives for focusing of light. It was shown, that advanced heat accumulation regime of femtosecond inscription is inapplicable for writing of near-surface waveguides, and near the surface waveguides should be written in non-thermal regime in contrast to widespread femtosecond writing at depths of tens micrometers. Inscribed waveguides were examined for optical losses and polarization properties. It was experimentally shown, that femtosecond written near surface waveguides have such advantages over widely used proton exchanged and Ti-diffusion waveguides as lower optical losses (down to 0.3 dB/cm) and maintaining of all polarization states of propagation light, which is crucial for development of electro-optical modulators for broadband and ultrashort laser emission. Novelty of the results consists in technique of femtosecond inscription of waveguides at record low depths under the surface of crystals. As compared to previous investigations in the field (structures at depths near 50 um with buried electrodes), the obtained waveguides could be used with simple closely adjacent on-surface electrodes.

  5. A 200 kHz Q-Switched Adhesive-Free Bond Composite Nd:YVO4 Laser using a Double-Crystal RTP Electro-optic Modulator

    Institute of Scientific and Technical Information of China (English)

    YU Yong-Ji; CHEN Xin-Yu; WANG Chao; WU Chun-Ting; LIU Rui; JIN Guang-Yong

    2012-01-01

    A diode-end-pumped electro-optic (EO) Q-switched adhesive-free bond composite Nd:YVO4 laser operating at a repetition rate of 200 kHz is reported. A pair of RbTiOPOi (RTP) crystals are used as a high repetition EO Q-switch. At the repetition rate of 200kHz, the maximum average output power of 11.8 W at wavelength 1064 nm and full width at half maximum of pulses of 16.65 ns are achieved at an incident pump power of 27 W, corresponding to an optical conversion efficiency of 43.7% and a slope efficiency of 44.6%, respectively. To the best of our knowledge, this is the highest repetition rate reported on the EO Q-switched laser by using RTP crystals.%A diode-end-pumped electro-optic (EO) Q-switched adhesive-free bond composite Nd:YVO4 laser operating at a repetition rate of 200 kHz is reported.A pair of RbTiOPO4 (RTP) crystals are used as a high repetition EO Q-switch.At the repetition rate of 200kHz,the maximum average output power of 11.8 W at wavelength 1064 nm and full width at half maximum of pulses of 16.65ns are achieved at an incident pump power of 27 W,corresponding to an optical conversion efficiency of 43.7% and a slope efficiency of 44.6%,respectively.To the best of our knowledge,this is the highest repetition rate reported on the EO Q-switched laser by using RTP crystals.

  6. Preliminary Evaluation of Removing Used Nuclear Fuel from Shutdown Sites

    Energy Technology Data Exchange (ETDEWEB)

    Maheras, Steven J.; Best, Ralph E.; Ross, Steven B.; Buxton, Kenneth A.; England, Jeffery L.; McConnell, Paul E.

    2013-09-30

    This report fulfills the M2 milestone M2FT-13PN0912022, “Stranded Sites De-Inventorying Report.” In January 2013, the U.S. Department of Energy (DOE) issued the Strategy for the Management and Disposal of Used Nuclear Fuel and High-Level Radioactive Waste (DOE 2013). Among the elements contained in this strategy is an initial focus on accepting used nuclear fuel from shutdown reactor sites. This focus is consistent with the recommendations of the Blue Ribbon Commission on America’s Nuclear Future, which identified removal of stranded used nuclear fuel at shutdown sites as a priority so that these sites may be completely decommissioned and put to other beneficial uses (BRC 2012). Shutdown sites are defined as those commercial nuclear power reactor sites where the nuclear power reactors have been shut down and the site has been decommissioned or is undergoing decommissioning. In this report, a preliminary evaluation of removing used nuclear fuel from 12 shutdown sites was conducted. The shutdown sites were Maine Yankee, Yankee Rowe, Connecticut Yankee, Humboldt Bay, Big Rock Point, Rancho Seco, Trojan, La Crosse, Zion, Crystal River, Kewaunee, and San Onofre. These sites have no other operating nuclear power reactors at their sites and have also notified the U.S. Nuclear Regulatory Commission that their reactors have permanently ceased power operations and that nuclear fuel has been permanently removed from their reactor vessels. Shutdown reactors at sites having other operating reactors are not included in this evaluation.

  7. Preliminary systems engineering evaluations for the National Ecological Observatory Network.

    Energy Technology Data Exchange (ETDEWEB)

    Robertson, Perry J.; Kottenstette, Richard Joseph; Crouch, Shannon M.; Brocato, Robert Wesley; Zak, Bernard Daniel; Osborn, Thor D.; Ivey, Mark D.; Gass, Karl Leslie; Heller, Edwin J.; Dishman, James Larry; Schubert, William Kent; Zirzow, Jeffrey A.

    2008-11-01

    The National Ecological Observatory Network (NEON) is an ambitious National Science Foundation sponsored project intended to accumulate and disseminate ecologically informative sensor data from sites among 20 distinct biomes found within the United States and Puerto Rico over a period of at least 30 years. These data are expected to provide valuable insights into the ecological impacts of climate change, land-use change, and invasive species in these various biomes, and thereby provide a scientific foundation for the decisions of future national, regional, and local policy makers. NEON's objectives are of substantial national and international importance, yet they must be achieved with limited resources. Sandia National Laboratories was therefore contracted to examine four areas of significant systems engineering concern; specifically, alternatives to commercial electrical utility power for remote operations, approaches to data acquisition and local data handling, protocols for secure long-distance data transmission, and processes and procedures for the introduction of new instruments and continuous improvement of the sensor network. The results of these preliminary systems engineering evaluations are presented, with a series of recommendations intended to optimize the efficiency and probability of long-term success for the NEON enterprise.

  8. Preliminary Design and Evaluation of Portable Electronic Flight Progress Strips

    Science.gov (United States)

    Doble, Nathan A.; Hansman, R. John

    2002-01-01

    There has been growing interest in using electronic alternatives to the paper Flight Progress Strip (FPS) for air traffic control. However, most research has been centered on radar-based control environments, and has not considered the unique operational needs of the airport air traffic control tower. Based on an analysis of the human factors issues for control tower Decision Support Tool (DST) interfaces, a requirement has been identified for an interaction mechanism which replicates the advantages of the paper FPS (e.g., head-up operation, portability) but also enables input and output with DSTs. An approach has been developed which uses a Portable Electronic FPS that has attributes of both a paper strip and an electronic strip. The prototype flight strip system uses Personal Digital Assistants (PDAs) to replace individual paper strips in addition to a central management interface which is displayed on a desktop computer. Each PDA is connected to the management interface via a wireless local area network. The Portable Electronic FPSs replicate the core functionality of paper flight strips and have additional features which provide a heads-up interface to a DST. A departure DST is used as a motivating example. The central management interface is used for aircraft scheduling and sequencing and provides an overview of airport departure operations. This paper will present the design of the Portable Electronic FPS system as well as preliminary evaluation results.

  9. Preventative Vaccines for Zika Virus Outbreak: Preliminary Evaluation

    Directory of Open Access Journals (Sweden)

    Eun Kim

    2016-11-01

    Full Text Available Since it emerged in Brazil in May 2015, the mosquito-borne Zika virus (ZIKV has raised global concern due to its association with a significant rise in the number of infants born with microcephaly and neurological disorders such as Guillain-Barré syndrome. We developed prototype subunit and adenoviral-based Zika vaccines encoding the extracellular portion of the ZIKV envelope gene (E fused to the T4 fibritin foldon trimerization domain (Efl. The subunit vaccine was delivered intradermally through carboxymethyl cellulose microneedle array (MNA. The immunogenicity of these two vaccines, named Ad5.ZIKV-Efl and ZIKV-rEfl, was tested in C57BL/6 mice. Prime/boost immunization regimen was associated with induction of a ZIKV-specific antibody response, which provided neutralizing immunity. Moreover, protection was evaluated in seven-day-old pups after virulent ZIKV intraperitoneal challenge. Pups born to mice immunized with Ad5.ZIKV-Efl were all protected against lethal challenge infection without weight loss or neurological signs, while pups born to dams immunized with MNA-ZIKV-rEfl were partially protected (50%. No protection was seen in pups born to phosphate buffered saline-immunized mice. This study illustrates the preliminary efficacy of the E ZIKV antigen vaccination in controlling ZIKV infectivity, providing a promising candidate vaccine and antigen format for the prevention of Zika virus disease.

  10. Preliminary Safety Evaluation of a New Bacteroides xylanisolvens Isolate

    Science.gov (United States)

    Toutounian, Kawe; Schmidt, Jens; Karsten, Uwe; Goletz, Steffen

    2012-01-01

    Besides conferring some health benefit to the host, a bacterial strain must present an unambiguous safety status to be considered a probiotic. We here present the preliminary safety evaluation of a new Bacteroides xylanisolvens strain (DSM 23964) isolated from human feces. First results suggest that it may be able to provide probiotic health benefits. Its identity was confirmed by biochemical analysis, by sequencing of its 16S rRNA genes, and by DNA-DNA hybridization. Virulence determinants known to occur in the genus Bacteroides, such the bft enterotoxin and other enzymatic activities involved in the degradation of the extracellular matrix and the capsular polysaccharide PS A, were absent in this strain. The investigation of the antibiotic susceptibility indicated that strain DSM 23964 was sensitive to metronidazole, meropenem agents, and clindamycin. Resistance to penicillin and ampicillin was identified to be conferred by the β-lactamase cepA gene and could therefore be restored by adding β-lactamase inhibitors. The localization of the cepA gene in the genome of strain DSM 23964 and the absence of detectable plasmids further suggest that a transfer of β-lactamase activity or the acquisition of other antibiotic resistances are highly improbable. Taken together, the presented data indicate that the strain B. xylanisolvens DSM 23964 has no virulence potential. Since it also resists the action of gastric enzymes and low-pH conditions, this strain is an interesting candidate for further investigation of its safety and potential health-promoting properties. PMID:22101046

  11. Preventative Vaccines for Zika Virus Outbreak: Preliminary Evaluation.

    Science.gov (United States)

    Kim, Eun; Erdos, Geza; Huang, Shaohua; Kenniston, Thomas; Falo, Louis D; Gambotto, Andrea

    2016-11-01

    Since it emerged in Brazil in May 2015, the mosquito-borne Zika virus (ZIKV) has raised global concern due to its association with a significant rise in the number of infants born with microcephaly and neurological disorders such as Guillain-Barré syndrome. We developed prototype subunit and adenoviral-based Zika vaccines encoding the extracellular portion of the ZIKV envelope gene (E) fused to the T4 fibritin foldon trimerization domain (Efl). The subunit vaccine was delivered intradermally through carboxymethyl cellulose microneedle array (MNA). The immunogenicity of these two vaccines, named Ad5.ZIKV-Efl and ZIKV-rEfl, was tested in C57BL/6 mice. Prime/boost immunization regimen was associated with induction of a ZIKV-specific antibody response, which provided neutralizing immunity. Moreover, protection was evaluated in seven-day-old pups after virulent ZIKV intraperitoneal challenge. Pups born to mice immunized with Ad5.ZIKV-Efl were all protected against lethal challenge infection without weight loss or neurological signs, while pups born to dams immunized with MNA-ZIKV-rEfl were partially protected (50%). No protection was seen in pups born to phosphate buffered saline-immunized mice. This study illustrates the preliminary efficacy of the E ZIKV antigen vaccination in controlling ZIKV infectivity, providing a promising candidate vaccine and antigen format for the prevention of Zika virus disease. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights reserved.

  12. Preliminary physicochemical evaluation of Kushta tutia: A Unani Formulation

    Directory of Open Access Journals (Sweden)

    Mohd Tariq

    2014-01-01

    Full Text Available Background: Kushta is an important solid dosage form of Unani system of medicine used to treat various ailments. Very small particle size of kushta is responsible for its rapid absorption in body leading to instant therapeutic actions. Kushta tutia (KT is one such renowned formulation used by hakims for successful management of various disorders. However, there is lack of scientific work on KT. Objectives: The present study was performed to evaluate KT physicochemically by testifying it on classical tests along with modern scientific techniques. Materials and Methods: Tutia was first detoxified as per classical literature. It was triturated with water and dried, afterwards subjected to calcination in furnace rather than cow dung cakes due to isolation of material being heated and better temperature control. Finished product was evaluated for physicochemical characteristics including preliminary tests mentioned in classical literature. Results: Floating and finger test were positive. Curd test showed no discoloration after 48 h. These findings indicate correct preparation of KT according to classical literature. Bulk density (0.96 ± 0.00 g/ml; tapped density (1.53 ± 0.00 g/ml; Hausner ratio (0.62 ± 0.00, compressibility index (37.52 ± 0.19%; loss of weight on drying (0.08 ± 0.00%; pH of 1 and 10% (5.20 ± 0.00 and 5.62 ± 0.00, respectively; total ash, acid insoluble ash, and water soluble ash values 95.75 ± 0.09, 6.57 ± 0.02, and 45.02 ± 0.20%, respectively; and extractive values 0.85 ± 0.02% were reported in KT. Conclusion: Since this work has not been reported earlier, the results obtained could be considered as the standard for KT for future studies.

  13. 车载负性CLCD电光特性研究%Research on Electro-optical Characteristic of Vehicle-mounted Negative CLCD

    Institute of Scientific and Technical Information of China (English)

    黄翀; 许国栋; 杨玮枫; 欧阳艳东; 吴永俊

    2014-01-01

    彩色液晶显示器件(CLCD)在相同电压驱动条件下,各波长电光特性有很大差异,从而对图像显示的色彩饱和度有较大的影响。用UV-Vis8500型双光束紫外/可见分光光度计测量在不同电压驱动下负性TN-LCD,STN-LCD和VA-LCD的电光特性,分析比较其三基色的电光特性、阈值特性和陡度随波长的变化关系。结果表明,TN-LCD的Vth、Vsat和V50随波长的增大而减小,而Vth、Vsat和V50减小的快慢基本一致;STN-LCD的Vth、Vsat和V50随波长的增大而减小,而Vth、Vsat和V50减小速度在各波长上快慢不一;VA-LCD的Vth、Vsat和V50都是随着波长的增加而逐渐增大,而Vsat增大速度比V50快,V50增大速度比Vth快。对常用三种不同负性液晶显示器件驱动电压的选取进行比较分析,其结果为CLCD选取驱动电压提供一定的指导作用。%Under the same driving voltage, the colorful liquid crystal display device (CLCD) has quite different electro-optical characteristics at different wavelength. As a result, the saturation of colorful display image could be greatly influenced. The electro-optical characteristics of negative TN-LCD, STN-LCD and VA-LCD driven by differ⁃ent voltage are measured by UV-Vis8500 double beam ultraviolet (UV)/visible spectrophotometer, from which the electro-optical and threshold characteristics of three primary colors and the gradient variation with wavelength are analyzed and compared. The results show that with the increasing of wavelength, Vth, Vsat and V50 of TN-LCD de⁃crease. And the decreasing speed of them is basically same. With the increasing of wavelength, Vth, Vsat and V50 of STN-LCD decrease. And the decreasing speed of them is different in each wavelength. With the increasing of wave⁃length, Vth, Vsat and V50 of VA-LCD increase gradually. But the increasing speed of Vsat is faster than that of V50 and the increasing speed of V50 is faster than that of Vth. The chosen

  14. Preliminary Evaluation of Removing Used Nuclear Fuel from Shutdown Sites

    Energy Technology Data Exchange (ETDEWEB)

    Maheras, Steven J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Best, Ralph E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Ross, Steven B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Buxton, Kenneth A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); England, Jeffery L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); McConnell, Paul E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Massaro, Lawrence M. [Federal Railroad Administration (FRA) (United States); Jensen, Philip J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2014-10-01

    This report presents a preliminary evaluation of removing used nuclear fuel (UNF) from 12 shutdown nuclear power plant sites. At these shutdown sites the nuclear power reactors have been permanently shut down and the sites have been decommissioned or are undergoing decommissioning. The shutdown sites are Maine Yankee, Yankee Rowe, Connecticut Yankee, Humboldt Bay, Big Rock Point, Rancho Seco, Trojan, La Crosse, Zion, Crystal River, Kewaunee, and San Onofre. The evaluation was divided into four components: characterization of the UNF and greater-than-Class C low-level radioactive waste (GTCC waste) inventory; a description of the on-site infrastructure and conditions relevant to transportation of UNF and GTCC waste; an evaluation of the near-site transportation infrastructure and experience relevant to shipping transportation casks containing UNF and GTCC waste, including identification of gaps in information; and, an evaluation of the actions necessary to prepare for and remove UNF and GTCC waste. The primary sources for the inventory of UNF and GTCC waste are the U.S. Department of Energy (DOE) RW-859 used nuclear fuel inventory database, industry sources such as StoreFUEL and SpentFUEL, and government sources such as the U.S. Nuclear Regulatory Commission. The primary sources for information on the conditions of site and near-site transportation infrastructure and experience included observations and information collected during visits to the Maine Yankee, Yankee Rowe, Connecticut Yankee, Humboldt Bay, Big Rock Point, Rancho Seco, Trojan, La Crosse, and Zion sites; information provided by managers at the shutdown sites; Facility Interface Data Sheets compiled for DOE in 2005; Services Planning Documents prepared for DOE in 1993 and 1994; industry publications such as Radwaste Solutions; and Google Earth. State and Regional Group representatives, a Tribal representative, and a Federal Railroad Administration representative participated in six of the shutdown site

  15. Preliminary Evaluation of Removing Used Nuclear Fuel from Shutdown Sites

    Energy Technology Data Exchange (ETDEWEB)

    Maheras, Steven J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Best, Ralph E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Ross, Steven B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Buxton, Kenneth A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); England, Jeffery L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); McConnell, Paul E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Massaro, Lawrence M. [Fermi Research Alliance (FRA), Batavia, IL (United States); Jensen, Philip J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-09-30

    A preliminary evaluation of removing spent nuclear fuel (SNF) from 13 shutdown nuclear power plant sites was performed. At these shutdown sites the nuclear power reactors have been permanently shut down and the sites have been decommissioned or are undergoing decommissioning. The shutdown sites were Maine Yankee, Yankee Rowe, Connecticut Yankee, Humboldt Bay, Big Rock Point, Rancho Seco, Trojan, La Crosse, Zion, Crystal River, Kewaunee, San Onofre, and Vermont Yankee. The evaluation was divided into four components: Characterization of the SNF and greater-than-Class C low-level radioactive waste (GTCC waste) inventory A description of the on-site infrastructure at the shutdown sites An evaluation of the near-site transportation infrastructure and transportation experience at the shutdown sites An evaluation of the actions necessary to prepare for and remove SNF and GTCC waste. The primary sources for the inventory of SNF and GTCC waste were the U.S. Department of Energy (DOE) spent nuclear fuel inventory database, industry publications such as StoreFUEL, and government sources such as the U.S. Nuclear Regulatory Commission. The primary sources for information on the conditions of on-site infrastructure and near-site transportation infrastructure and experience included information collected during site visits, information provided by managers at the shutdown sites, Facility Interface Data Sheets compiled for DOE in 2005, Services Planning Documents prepared for DOE in 1993 and 1994, industry publications such as Radwaste Solutions, and Google Earth. State staff, State Regional Group representatives, a Tribal representative, and a Federal Railroad Administration representative have participated in nine of the shutdown site visits. Every shutdown site was found to have at least one off-site transportation mode option for removing its SNF and GTCC waste; some have multiple options. Experience removing large components during reactor decommissioning provided an

  16. Preliminary evaluation of the hydrogeologic system in Owens Valley, California

    Science.gov (United States)

    Danskin, W.R.

    1988-01-01

    A preliminary, two-layer, steady-state, groundwater flow model was used to evaluate present data and hydrologic concepts of Owens Valley, California. Simulations of the groundwater system indicate that areas where water levels are most affected by changes in recharge and discharge are near toes of alluvial fans and along the edge of permeable volcanic deposits. Sensitivity analysis for each model parameter shows that steady state simulations are most sensitive to uncertainties in evapotranspiration rates. Tungsten Hills, Poverty Hills, and Alabama Hills were found to act as virtually impermeable barriers to groundwater flow. Accurate simulation of the groundwater system between Bishop and Lone Pine appears to be possible without simulating the groundwater system in Round Valley, near Owens Lake, or in aquifer materials more than 1,000 ft below land surface. Although vast amounts of geologic and hydrologic data have been collected for Owens Valley, many parts of the hydrogeologic system have not been defined with sufficient detail to answer present water management questions. Location and extent of geologic materials that impede the vertical movement of water are poorly documented. The likely range of aquifer characteristics, except vertical hydraulic conductivity, is well known, but spatial distribution of these characteristics is not well documented. A set of consistent water budgets is needed, including one for surface water, groundwater, and the entire valley. The largest component of previous water budgets (evapotranspiration) is largely unverified. More definitive estimates of local gains and losses for Owens River are needed. Although groundwater pumpage from each well is measured, the quantity of withdrawal from different zones of permeable material has not been defined. (USGS)

  17. 基于电光调制的毫米波辐射计研究%Millimeter-wave radiometer based on electro-optic modulation

    Institute of Scientific and Technical Information of China (English)

    张跃东; 江月松; 何云涛; 邓士光

    2011-01-01

    研究了一种通过电光调制将毫米波信号加载到光载波上进行处理的毫米波辐射计。天线接收的毫米波信号由电光调制器(EOM)调制加载到光载波的边带上,并通过光纤传输该信号;利用光纤布拉格光栅(FBG)滤波器滤掉载波分量,滤波后保留的边带分量信号由光电探测器(PD)探测。为提高探测灵敏度,使用锁相放大器对PD输出的信号进行检测。分析了采用光学方法处理毫米波信号时的能量转换效率和噪声特性。使用50GHz毫米波信号源对毫米波信号进行了探测实验,测量了实验系统中的能量转换效率和噪声等效功率,并分析了改进探测灵敏度的方法。设%A millimeter-wave radiometer using electro-optic modulation and photodetection is presented.The millimeter-wave energy collected by the antenna is transferred to the sidebands of the optical carrier by an electro-optic modulator,and then transmitted through the optical fiber.Fiber Bragg grating filters are subsequently used to suppress the optical carrier and a photo-detector is used to detect the energy in the remaining sideband.The output signal of the photo-detector is detected by a lock-in amplifier to improve the sensitivity.The energy conversion efficiency and noise characteristics in the millimeter-wave signal processing are discussed.The millimeter-wave detection experiment based on this technique was implemented using a 50 GHz millimeter-wave source.The conversion efficiency and the noise equivalent power were measured.The methods for improving the sensitivity were proposed.A millimeter-wave radiometric detection system was designed.The detection experimental results show that this millimeter-wave signal processing method is effective for millimeter-wave radiometer.

  18. Electro-optic modulators with self-assembled superlattice waveguides%自聚焦超晶格波导电光调制器

    Institute of Scientific and Technical Information of China (English)

    孙德贵; 刘志福; HO Seng-Tiong; 康虎; 朱培旺; MARKS Tobin

    2004-01-01

    研制了一种基于自聚焦超晶格薄膜电光波导调制器.首先给出了自聚焦超晶格薄膜电光特性的测量和器件结构的优化设计,采用测量二次谐波生成值对入射角的依赖关系测定了薄膜的有效电光系数,保证了器件的设计精确有效.利用多层膜传输理论研究了器件电极对光波的最大吸收,并对器件结构进行了优化,获得了最小调制电压.其次给出了所加工的实验模型结构和扫描电子显微镜(SEM)图片,确保了加工质量和设计结果的一致.研究结果表明:这种无需外电场极化处理的新型聚合物薄膜电光调制器加工难度小,并且光学损耗优化到了1.0 dB/cm.%This paper reports a new waveguide electro-optic (EO) modulator with self-assembled superlattice (SAS) electro-optic films. This work focuses on the measurement for the EO coefficient of SAS films and the optimization for the devices structure. In order to have a precise and effective design, we test the angle-dependence of the second harmonic generation of incident laser beam to determine the effective EO coefficient. We study he absorptive loss of electrodes of devices with the optical propagation theory of multi-layered films and optimize the devices structure to obtain the lowest drive voltage. The paper gives the structure of experimental samples and the scanned electronic microscopy (SEM) pictures of our fabricated devices. Finally, 1.0 dB/cm optical propagation loss of the EO modulators is achieved, which agrees with the experimental results.

  19. SYNTHESIS OF DIACETYLENE-CONTAINING COPOLYESTERS AND THEIR EFFECT ON ELECTRO-OPTICAL PROPERTIES OF LIQUID CRYSTALS

    Institute of Scientific and Technical Information of China (English)

    Xiao-fang Chen; Yao-wen Bai; Yu-guo Ma; Chen-hui Wang; Dong Zhang; Xin-hua Wan; Qi-feng Zhou

    1999-01-01

    Some diacetylene-containing copolyesters with different ratios of dipropargyl 1,10-decanate and dipropargyl terephthalate were synthesized. Properties of these copolymers were characterized by differential scanning calorimetry and polarizing optical microscopy. The copolymer could be cross-linked easily by UV irradiation in a liquid crystal matrix without adding any photoinitiator. The preliminary studies showed that the diacetylene-containing polymer network can assist liquid crystal molecules to align with the external electric field, thus reducing the response time of display devices.

  20. Voltages and electric currents mensuration - class 15 kV - for systems electro-optical and magneto-optical; Medicao de tensoes e correntes - classe 15 kv - por sistemas eletro-opticos e magneto-opticos

    Energy Technology Data Exchange (ETDEWEB)

    Costa, Marcos Rodrigues

    1996-07-01

    The technical feasibility of the development of a novel system measuring of high voltage and current in 15 kV distribution lines was presented. The system is basically the combination of two other systems, one conventional and other electro-optical. The conventional subsystem is based on voltage dividers and magnetic rings while the electro-optical subsystem uses LEDs, resistors, optical-fibers and photodetectors. The system was completely tested in laboratory and its main characteristics are low price, easy of installation and flexibility. Two software for data acquisition by GPIB and A/D boards were also developed. The can provide reports on voltages, currents, power and phase-power. (author)

  1. Feasibility Study of the γ51-Based Electro-Optic Modulator%基于γ51的电光调制器的可行性研究

    Institute of Scientific and Technical Information of China (English)

    周幼华; 顾豪爽

    2011-01-01

    通过对不同晶系线性电光系数矩阵的分析计算,研究了利用晶体电光系数γ51实现电光调制的可能性.结果分析表明,在电场中的y51引起折射率的变化与x方向电场强度E21成正比;利用KTa0.35Nb0.65O3晶体的巨大γ51参数引起的二次电光效应,可以获得较低的半波电压;在立方-四方相变点附近的KTa1-xNbxO3晶体有极大克尔系数的现象,同时γ51参数电光效应也得到了解释.%The feasibility of electro-optic modulation based on electro-optical coefficient γ51 was investigated, by calculating linear electro-optical coefficient matrix consisting of γ51. The variety of the relative index induced by the field was proportional to E21. It could give an explanation of giant Kerr coefficient around the cubic-tetragonal phase transition of KTa1-xNbxO3. And a design proposal of electro-optic modulation utilizing γ51 of KTa0.35Nb0.65 O3 was introduced.

  2. Preliminary evaluation of diabatic heating distribution from FGGE level 3b analysis data

    Science.gov (United States)

    Kasahara, A.; Mizzi, A. P.

    1985-01-01

    A method is presented for calculating the global distribution of diabatic heating rate. Preliminary results of global heating rate evaluated from the European center for Medium Range Weather Forecasts Level IIIb analysis data is also presented.

  3. How does the increment of hetero-cyclic conjugated moieties affect electro-optical and charge transport properties of novel naphtha-difuran derivatives? A computational approach.

    Science.gov (United States)

    Chaudhry, Aijaz Rasool; Ahmed, R; Irfan, Ahmad; Muhammad, Shabbir; Shaari, A; Al-Sehemi, Abdullah G

    2014-12-01

    We have investigated computationally the effects of π-conjugation extension on naphtha[2,1-b:6,5-b'] difuran (DPNDF); where we increase the number of fused NDF (central core) and furan rings in the parent molecule. The molecular structures of all analogues have been optimized at the ground (S0) and first excited (S1) states using density functional theory (DFT) and time-dependent density functional theory (TD-DFT), respectively. Then highest occupied molecular orbitals (HOMOs), the lowest unoccupied molecular orbitals (LUMOs), photophysical properties, adiabatic/vertical electron affinities (EAa)/(EAv), adiabatic/vertical ionization potentials (IPa)/(IPv), and hole/electron reorganization energies λh/λe have been investigated. The effect of NDF and furan rings on structural and electro-optical properties has also been studied. Our calculated reorganization energies of 1a, 1b, and 2c reveal them, materials with balanced hole/electron charge transport, whereas 2a and 2b are good hole-transport materials. By increasing the number of furan rings; the photostability was augmented in 2a, 2b, and 2c.

  4. Low driving voltage Mach-Zehnder interference modulator constructed from an electro-optic polymer on ultra-thin silicon with a broadband operation.

    Science.gov (United States)

    Sato, Hiromu; Miura, Hiroki; Qiu, Feng; Spring, Andrew M; Kashino, Tsubasa; Kikuchi, Takamasa; Ozawa, Masaaki; Nawata, Hideyuki; Odoi, Keisuke; Yokoyama, Shiyoshi

    2017-01-23

    An electro-optic (EO) polymer waveguide using an ultra-thin silicon hybrid has been designed and fabricated. The silicon core has the thickness of 50 nm and a width of 5 μm. The waveguide was completed after covering the cladding with the high temperature stable EO polymer. We have demonstrated a low half-wavelength voltage of 0.9 V at the wavelength of 1.55 μm by using a Mach-Zehnder interference modulator with TM mode operation. The measured modulation corresponded to an effective in-device EO coefficient of 165 pm/V. By utilizing the traveling-wave electrode on the modulator the high-frequency response was tested up to 40 GHz. The 3 dB modulation bandwidth was measured to be 23 GHz. In addition, the high frequency sideband spectral measurement revealed that a linear response of the modulation index against the RF power was confirmed up to 40 GHz signal.

  5. Implementation of electro-optic amplitude modulator in the external cavity of semiconductor laser for generation of periodic sates and chaos control

    Directory of Open Access Journals (Sweden)

    Kh Mabhouti

    2016-12-01

    Full Text Available In this paper, by placing the electro optical modulator (EOM into the external cavity of the semiconductor laser (SL and amplitude modulation of the optical feedback, the dynamical variation of the output intensity  of the laser has been studied. This is analyzed numerically via bifurcation and time series diagrams with respect to the applied amplitude modulation index, and modulation voltage frequency of the EOM. It has been shown that, by modulating the amplitude of the optical feedback beam, various changes in the types of the dynamics of  can be observed, and various periodic states can be generated. This makes it possible to receive the desired dynamics without any variations in the main parameters of the SL. Also, in present study, a method of chaos control in the SL has been presented based on EOM in the external cavity. The obtained results confirm that based on this method the chaotic dynamics can be controlled single-periodic dynamics

  6. Adsorbate-induced modification of the surface electric field of GaAs (001)-c(4 x 4) measured via the linear electro-optic effect

    Energy Technology Data Exchange (ETDEWEB)

    Bruhn, T.; Passmann, R.; Esser, N.; Vogt, P. [Institut fuer Festkoerperphysik, Technische Universitaet Berlin, Hardenbergstr. 36, 10623 Berlin (Germany); Leibniz-Institut fuer Analytische Wissenschaften - ISAS - e.V., Albert-Einstein-Str. 9, 12489 Berlin (Germany); Fimland, B.O. [Department of Electronics and Telecommunications, Norwegian University of Science and Technology, NO-7491 Trondheim (Norway); Kneissl, M. [Institut fuer Festkoerperphysik, Technische Universitaet Berlin, Hardenbergstr. 36, 10623 Berlin (Germany)

    2010-08-15

    We have investigated the modification of the surface electric field (SEF) of the GaAs (001)-c(4 x 4) surface during the adsorption of cyclopentene and 1,4-cyclohexadiene molecules by reflectance anisotropy spectroscopy (RAS) in the spectral range from 1.5 to 5.0 eV. At around 3 eV the RAS line shape originates from the so-called linear electro-optic effect (LEO). The amplitude of the LEO oscillation scales linearly with the SEF within the RAS penetration depth and is thus a measure for it. For the separation of the LEO from the RAS spectra several different methods are described in the literature. Here, we present a modified method which allows the LEO separation in particular for interfaces between GaAs and organic molecules. The results obtained this way show a significant increase of the LEO effect upon molecule adsorption indicating a higher SEF. The observed changes of the surface electronic properties are probably related to a modification of surface strain upon molecule adsorption. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

  7. Electro-optical time gating based on Mach-Zehnder modulator for multiple access interference elimination in optical code-division multiple access networks

    Science.gov (United States)

    Chen, Yinfang; Wang, Rong; Fang, Tao; Pu, Tao; Xiang, Peng; Zheng, Jilin; Zhu, Huatao

    2014-05-01

    An electro-optical time gating technique, which is based on an electrical return-to-zero (RZ) pulse driven Mach-Zehnder modulator (MZM) for eliminating multiple access interference (MAI) in optical code-division multiple access (OCDMA) networks is proposed. This technique is successfully simulated in an eight-user two-dimensional wavelength-hopping time-spreading system, as well as in a three-user temporal phase encoding system. Results show that in both systems the MAI noise is efficiently removed and the average received power penalty improved. Both achieve error-free transmissions at a bit rate of 2.5 Gb/s. In addition, we also individually discuss effects of parameters in two systems, such as the extinction ratio of the MZM, the duty cycle of the driven RZ pulse, and the time misalignment between the driven pulse and the decoded autocorrelation peak, on the output bit error rate performance. Our work shows that employing a common MZM as a thresholder provides another probability and an interesting cost-effective choice for a smart size, low energy, and less complex thresholding technique for integrated detection in OCDMA networks.

  8. Superior electro-optical properties of electrically controlled birefringence mode using solution-derived La{sub 2}O{sub 3} films

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Hae-Chang; Park, Hong-Gyu; Lee, Ju Hwan; Seo, Dae-Shik, E-mail: dsseo@yonsei.ac.kr [Information Display Device Laboratory, Department of Electrical and Electronic Engineering, Yonsei University, 50 Yonsei-ro, Seodaemun-gu, Seoul 120-749 (Korea, Republic of); Oh, Byeong-Yun [ZeSHTech Co., Ltd., Business Incubator, Gwangju Institute of Science and Technology, 123, Cheomdangwagi-ro, Buk-gu, Gwangju 500-712 (Korea, Republic of)

    2015-11-15

    The authors demonstrate a high performance electrically controlled birefringence (ECB) mode with solution-derived La{sub 2}O{sub 3} films at various molar concentrations. Uniform and homogeneous liquid crystal (LC) alignment was spontaneously achieved on the La{sub 2}O{sub 3} films for lanthanum concentrations at ratios greater than and equal to 0.2. A preferred orientation of LC molecules appeared along the filling direction, and the LC alignment was maintained via van der Waals force by nanocrystals of the La{sub 2}O{sub 3} films. The LC alignment mechanism was confirmed by x-ray photoelectron spectroscopy and high-resolution transmission electron microscopy analysis. Superior electro-optical characteristics of the ECB cells constructed with solution-derived La{sub 2}O{sub 3} films were observed, which suggests that the proposed solution-derived La{sub 2}O{sub 3} films have strong potential for use in the production of advanced LC displays.

  9. Phase Velocity Estimation of a Microstrip Line in a Stoichiometric Periodically Domain-Inverted LiTaO3 Modulator Using Electro-Optic Sampling Technique

    Directory of Open Access Journals (Sweden)

    Shintaro Hisatake

    2008-01-01

    Full Text Available We estimate the phase velocity of a modulation microwave in a quasi-velocity-matched (QVM electro-optic (EO phase modulator (QVM-EOM using EO sampling which is accurate and the most reliable technique for measuring voltage waveforms at an electrode. The substrate of the measured QVM-EOM is a stoichiometric periodically domain-inverted LiTaO3 crystal. The electric field of a standing wave in a resonant microstrip line (width: 0.5 mm, height: 0.5 mm is measured by employing a CdTe crystal as an EO sensor. The wavelength of the traveling microwave at 16.0801 GHz is determined as 3.33 mm by fitting the theoretical curve to the measured electric field distribution. The phase velocity is estimated as vm=5.35×107 m/s, though there exists about 5% systematic error due to the perturbation by the EO sensor. Relative dielectric constant of εr=41.5 is led as the maximum likelihood value that derives the estimated phase velocity.

  10. Exploring electro-optic effect and third-order nonlinear optical susceptibility of impurity doped quantum dots: Interplay between hydrostatic pressure, temperature and noise

    Science.gov (United States)

    Ganguly, Jayanta; Saha, Surajit; Bera, Aindrila; Ghosh, Manas

    2017-03-01

    We study the profiles of electro-optic effect (EOE) and third-order nonlinear optical susceptibility (TONOS) of impurity doped GaAs quantum dots (QDs) under the combined influence of hydrostatic pressure (HP) and temperature (T) taking into account the presence of Gaussian white noise. Noise has been introduced to the system additively and multiplicatively. The doped dot has been subjected to a polarized monochromatic electromagnetic field. Effect of application of noise is elegantly reflected through prominent change of peak shift (blue/red) and variation of peak height (increase/ıdecrease) of above nonlinear optical (NLO) properties as temperature and pressure are varied over a range. Interestingly, all such changes subtly depend on mode of application (additive/multiplicative) of noise. The noteworthy influence of the interplay between noise strength and its mode of application on the said NLO properties has also been critically scrutinized. The findings highlight remarkable role played by noise in tuning above NLO properties of doped QD system under the prominent presence of both hydrostatic pressure and temperature.

  11. Results from the electro-optic sensors domain of the materials and components for missiles innovation and technology partnership (phase 1)

    Science.gov (United States)

    Bray, Mark E.; Shears, Robert A.

    2013-10-01

    The Materials and Components for Missiles Innovation and Technology Partnership (ITP) is a research programme supporting research for guided weapons at Technology Readiness Levels 1 to 4. The Anglo-French initiative is supported by the DGA and the MoD, with matched funding from industry. A major objective is to foster projects which partner UK and French universities, SMEs and larger companies. The first projects started in January 2008 and the first phase completed in spring 2013. Providing funding is secured, the next phase of the programme is due to start later in 2013. Selex ES leads Domain 3 of the MCM-ITP which develops Electro-Optic sensor technology. In collaboration with DGA, MoD and MBDA, the prime contractor, we identified 4 key objectives for the first ITP phase and focussed resources on achieving these. The objectives were to enable better imagery, address operationally stressing scenarios, provide low overall through life cost and improve active and semi-active sensors Nine normal projects and one ITP innovation fund project have been supported within the domain. The technology providers have included 3 SMEs and 8 research centres from both the United Kingdom and France. Highlights of the projects are included. An outline of the priorities for the domain for the new phase ise provided and we encourage organisations with suitable technology to contact us to get involved.

  12. An electro-optical and electron injection study of benzothiazole-based squaraine dyes as efficient dye-sensitized solar cell materials: a first principles study.

    Science.gov (United States)

    Al-Fahdan, Najat Saeed; Asiri, Abdullah M; Irfan, Ahmad; Basaif, Salem A; El-Shishtawy, Reda M

    2014-12-01

    Squaraine dyes have attracted significant attention in many areas of daily life from biomedical imaging to semiconducting materials. Moreover, these dyes are used as photoactive materials in the field of solar cells. In the present study, we investigated the structural, electronic, photophysical, and charge transport properties of six benzothiazole-based squaraine dyes (Cis-SQ1-Cis-SQ3 and Trans-SQ1-Trans-SQ3). The effect of electron donating (-OCH3) and electron withdrawing (-COOH) groups was investigated intensively. Ground state geometry and frequency calculations were performed by applying density functional theory (DFT) at B3LYP/6-31G** level of theory. Absorption spectra were computed in chloroform at the time-dependent DFT/B3LYP/6-31G** level of theory. The driving force of electron injection (ΔG (inject)), relative driving force of electron injection (ΔG r (inject)), electronic coupling constants (|VRP|) and light harvesting efficiency (LHE) of all six compounds were calculated and compared with previously studied sensitizers. The ΔG (inject), ΔG r (inject) and |VRP| of all six compounds revealed that these sensitizers would be efficient dye-sensitized solar cell materials. Cis/Trans-SQ3 exhibited superior LHE as compared to other derivatives. The Cis/Trans geometric effect was studied and discussed with regard to electro-optical and charge transport properties.

  13. 光电综合搜索平台集成化设计%Research on the Integrated Design of Electro-optical Search Platform

    Institute of Scientific and Technical Information of China (English)

    游小嘉; 朱元武; 解志红; 王玉华

    2014-01-01

    Fast target recognition is the premise to weapon attack. Electro-optical search platform is an important reconnaissance equipment under the information condition. Aiming at improving the fast and autonomous target recognition of weapon system,we research on visible camera,IR imager and MMV radar integrated technology. Combing with autonomous recognition and high stability accuracy,detector selection,general design of platform and high stability accuracy control were discussed.%目标的快速捕获是作战武器实施打击的前提,光电综合搜索平台是信息化条件下的重要侦察设备。以提高武器系统快速、自主目标搜索为目标,对可见光摄像机、红外热像仪、毫米波雷达探测综合集成技术进行研究。结合光电综合搜索平台的自主搜索、高精度稳定的要求,从探测器选型、平台总体设计、高精度稳定控制等方面进行了论述。

  14. A long-term frequency-stabilized erbium-fiber-laser-based optical frequency comb with an intra-cavity electro-optic modulator

    CERN Document Server

    Zhang, Y; Zhao, W; Meng, S; Fan, S; Zhang, L; Guo, G; Zhang, S; Jiang, H

    2014-01-01

    We demonstrate a home-made optical frequency comb based on an erbium-doped-fiber femtosecond laser with a ring cavity. The repetition rate of the laser is about 209 MHz determined by optical length of the laser cavity. By controlling an intra-cavity electro-optic modulator and a Piezo-transducer, the repetition rate can be stabilized with megahertz bandwidth in a range of 3 kilohertz, enabling long-term repetition rate phase-locking. The in-loop frequency instability of the repetition rate, limited by measurement system, is 1.3E-13 at 1 second integration time and inversely proportional to integration time for short terms. Using a common path f-2f interferometer, the carrier envelope offset (CEO) frequency of the frequency comb is obtained with a signal-to-noise ratio of 40 dB for 3 megahertz resolution spectrum. Stabilized CEO frequency exhibits a deviation of 0.6 milihertz at 1 second integration time.

  15. Supervisory control of remote manipulation: A preliminary evaluation

    Science.gov (United States)

    Starr, G. P.

    1981-01-01

    A system for supervisory control is described, and preliminary results are presented. Supervisory control, where control is traded between man and computer, offers benefits in the control of a remote manipulator. The system has the potential to accomplish sophisticated tasks. It is indicated that supervisory control yields lower task completion times and is preferred over manual control.

  16. Preliminary evaluation of the tibial tuberosity-trochlear groove measurement

    DEFF Research Database (Denmark)

    Miles, James Edward; Kirpensteijn, Jolle; Svalastoga, Eiliv Lars

    guide surgical treatment. The TTTG measures tibial tuberosity position relative to the axis of the femoral trochlea. A preliminary investigation of TTTG measurement was performed using the red fox (Vulpes vulpes) cadavers as a morphologically similar and homogenous substitute for dog cadavers. CT...

  17. Comparative study of structural and electro-optical properties of ZnO:Ga films grown by steered cathodic arc plasma evaporation and sputtering on plastic and their application on polymer-based organic solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Liang, Chih-Hao, E-mail: dataman888@hotmail.com [R& D Division, Walsin Technology Corporation, Kaohsiung, Taiwan (China); Hsiao, Yu-Jen [National Nano Device Laboratories, National Applied Research Laboratories, Tainan, Taiwan (China); Hwang, Weng-Sing [Department of Materials Science and Engineering, National Cheng Kung University, Tainan, Taiwan (China)

    2016-08-01

    Ga-doped ZnO (GZO) films with various thicknesses (105–490 nm) were deposited on PET substrates at a low temperature of 90 °C by a steered cathodic arc plasma evaporation (steered CAPE), and a GZO film with a thickness of 400 nm was deposited at 90 °C by a magnetron sputtering (MS) for comparison. The comparative analysis of the microstructure, residual stress, surface morphology, electrical and optical properties, chemical states, and doping efficiency of the films produced by the steered CAPE and MS processes was performed, and the effect of thickness on the CAPE-grown GZO films was investigated in detail. The results showed that the GZO films grown by steered CAPE exhibited higher crystallinity and lower internal stress than those deposited by MS. The transmittance and electrical properties were also enhanced for the steered CAPE-grown films. The figure of merit (Φ = T{sup 10}/R{sub s}, where T is the transmittance and R{sub s} is the sheet resistance in Ω/□). was used to evaluate the performance of the electro-optical properties. The GZO films with a thickness of 400 nm deposited by CAPE had the highest Φ value, 1.94 × 10{sup −2} Ω{sup −1}, a corresponding average visible transmittance of 88.8% and resistivity of 6.29 × 10{sup −4} Ω·cm. In contrast, the Φ value of MS-deposited GZO film with a thickness of 400 nm is only 1.1 × 10{sup −3} Ω{sup −1}. This can be attributed to the increase in crystalline size, [0001] preferred orientation, decrease in stacking faults density and Ar contamination in steered CAPE-grown films, leading to increases in the Hall mobility and carrier density. In addition, the power conversion efficiency (PCE) of organic solar cells was significantly improved by using the CAPE-grown GZO electrode, and the PCE values were 1.2% and 1.7% for the devices with MS-grown and CAPE-grown GZO electrodes, respectively. - Highlights: • ZnO:Ga (GZO) films were grown on PET by steered cathodic arc plasma evaporation (CAPE

  18. A proposal for digital electro-optic switches with free-carrier dispersion effect and Goos-Hanchen shift in silicon-on-insulator waveguide corner mirror

    Science.gov (United States)

    Sun, DeGui

    2013-09-01

    In a silicon-on-insulator (SOI) waveguide corner mirror (WCM) structure, with the quantum process of a frustrated total internal reflection (FTIR) phenomenon and the time delay principle in the two-dimensional potential barrier tunneling process of a mass of particles, we derive an accurate physical model for the Goos-Hanchen (GH) shift of optical guided-mode in the FTIR process, and in principle match the GH shift jumping states with the independent guided-modes. Then, we propose and demonstrate a new regime of 1 × N digital optical switches with a matching state between the free-carrier dispersion (FCD) based refractive index modulation (RIM) of silicon to create a GH shift jumping function of a photonic signal at the reflecting interface and the independent guided-modes in the FTIR process, where a MOS-capacitor type electro-optic modulation regime is proposed and discussed to realize an effective FCD-based RIM. At the critical matching state, i.e., the incident of an optical beam is at the vicinity of Brewster angle in the WCM, a mini-change of refractive index of waveguide material can cause a great jump of GH shift along the FTIR reflecting interface, and further a 1 × N digital optical switching process could be realized. For a 350-500 nm single-mode rib waveguide made on the 220 nm CMOS-compatible SOI substrate and with the FCD effect based RIM of silicon crystal, a concentration variation of 1018-1019 cm-3 has caused a 0.5-2.5 μm GH shift of reflected beam, which is at 2-5 times of a mode-size and hence radically convinces an optical switching function with a 1 × 3-1 × 10 scale.

  19. Stabilization of a high-order harmonic generation seeded extreme ultraviolet free electron laser by time-synchronization control with electro-optic sampling

    Institute of Scientific and Technical Information of China (English)

    H.Tomizawa; T.Sato; K.Ogawa; K.Togawa; T.Tanaka; T.Hara; M.Yabashi; H.Tanaka; T.Ishikawa; T.Togashi; S.Matsubara; Y.Okayasu; T.Watanabe; E.J.Takahashi; K.Midorikawa; M.Aoyama; K.Yamakawa; S.Owada; A.Iwasaki; K.Yamanouchi

    2015-01-01

    A fully coherent free electron laser(FEL) seeded with a higher-order harmonic(HH) pulse from high-order harmonic generation(HHG) is successfully operated for a sufficiently prolonged time in pilot user experiments by using a timing drift feedback. For HHG-seeded FELs, the seeding laser pulses have to be synchronized with electron bunches. Despite seeded FELs being non-chaotic light sources in principle, external laser-seeded FELs are often unstable in practice because of a timing jitter and a drift between the seeding laser pulses and the accelerated electron bunches. Accordingly,we constructed a relative arrival-timing monitor based on non-invasive electro-optic sampling(EOS). The EOS monitor made uninterrupted shot-to-shot monitoring possible even during the seeded FEL operation. The EOS system was then used for arrival-timing feedback with an adjustability of 100 fs for continual operation of the HHG-seeded FEL. Using the EOS-based beam drift controlling system, the HHG-seeded FEL was operated over half a day with an effective hit rate of 20%–30%. The output pulse energy was 20 μJ at the 61.2 nm wavelength. Towards seeded FELs in the water window region, we investigated our upgrade plan to seed high-power FELs with HH photon energy of 30–100 e V and lase at shorter wavelengths of up to 2 nm through high-gain harmonic generation(HGHG) at the energy-upgraded SPring-8Compact SASE Source(SCSS) accelerator. We studied a benefit as well as the feasibility of the next HHG-seeded FEL machine with single-stage HGHG with tunability of a lasing wavelength.

  20. Effect of internal stress on the electro-optical behaviour of Al-doped ZnO transparent conductive thin films

    Science.gov (United States)

    Proost, J.; Henry, F.; Tuyaerts, R.; Michotte, S.

    2016-08-01

    In this work, we will report on scientific efforts aimed at unraveling the quantitative effect of elastic strain on the electro-optical behaviour of Al-doped zinc oxide (AZO). AZO thin films have been deposited by reactive magnetron sputtering to thicknesses from 300 to 500 nm, both on extra-clear glass substrates as well as on oxidised Si wafers. This resulted in both cases in polycrystalline, strongly textured (002) films. During deposition, the internal stress evolution in the growing film was monitored in-situ using high resolution curvature measurements. The resulting growth-induced elastic strain, which was found to depend heavily on the oxygen partial pressure, could further be modulated by appropriately choosing the deposition temperature. The latter also induces an additional extrinsic thermal stress component, whose sign depends on the substrate used. As such, a wide range of biaxial internal stresses could be achieved, from -600 MPa in compression up to 800 MPa in tension. The resulting charge carrier mobilities, obtained independently from room temperature Hall measurements, were found to range between 5 and 25 cm2/V s. Interestingly, the maximum mobility occurred at the zero-stress condition, and together with a charge carrier concentration of about 8 × 1020 cm-3, this gave rise to a resistivity of only 300 μΩ cm. From the stress-dependent optical transmission spectra in the range of 200-1000 nm, the pressure coefficient of the optical bandgap was estimated from the corresponding Tauc plots to be 31 meV/GPa, indicating a very high strain-sensitivity as well.

  1. Cultural Perspective On the Phenomenon of "Electro-optical Liu"%文化视角的“电光刘”现象之简析

    Institute of Scientific and Technical Information of China (English)

    王庆鹏

    2011-01-01

    Fuzhou Three Alleys and Seven Lanes"Electro-optical Liu" is a miracle in Fujian's recent economic history. Its grand scale, management of advanced technology, courageous and insightful key figures and elite family members make it more outstanding than its counterparts. The geographical environment of Fujian shaped Fujian na- tives' marine cultural character; Three Alleys and Seven Lanes and his family's business atmosphere are conducive to their growth; Educational tradition makes them have Chinese and Western perspective. In a word, it is the product of the junction of marine culture, Central Chinese culture and Westem culture.%福州三坊七巷“电光刘”是福建近代经济史上的一枝奇葩。它规模宏大,管理技术先进,核心人物有魄力和眼光,家族成员多英才,这些与本地工商业家族和外地同行相比,出类拔萃,一枝独秀。究其原因,福建的地理环境塑造了闽人海洋文化的性格;三坊七巷和其家族的工商业气氛有利于其成长;崇文重教的传统使其具备中西眼光。简言之,它是海洋文化、中原文化、西方文化交汇的产物。

  2. A Preliminary Evaluation of Reach: Training Early Childhood Teachers to Support Children's Social and Emotional Development

    Science.gov (United States)

    Conners-Burrow, Nicola A.; Patrick, Terese; Kyzer, Angela; McKelvey, Lorraine

    2017-01-01

    This paper describes the development, implementation and preliminary evaluation of the Reaching Educators and Children (REACH) program, a training and coaching intervention designed to increase the capacity of early childhood teachers to support children's social and emotional development. We evaluated REACH with 139 teachers of toddler and…

  3. Preliminary evaluation of vector flow and spectral velocity estimation

    DEFF Research Database (Denmark)

    Pedersen, Mads Møller; Pihl, Michael Johannes; Haugaard, Per

    Spectral estimation is considered as the golden standard in ultrasound velocity estimation. For spectral velocity estimation the blood flow angle is set by the ultrasound operator. Vector flow provides temporal and spatial estimates of the blood flow angle and velocity. A comparison of vector flow...... agrees with the spectral flow angle. The vector velocity estimates agrees with the spectral estimates at PS and ED. From preliminary data it is concluded that vector flow angle estimation can replace the operator-dependent angle correction used for spectral velocity estimation....... estimation and spectral estimates is presented. The variation of the blood flow angle and the effect on the velocity estimate is investigated. The right common carotid arteries of three healthy volunteers were scanned. Real-time spectral and vector flow data were obtained simultaneously from one range gate...

  4. Preliminary evaluation of two new cable surface innovations

    DEFF Research Database (Denmark)

    Burlina, Celeste; Georgakis, Christos T.; Larsen, S.V.;

    2015-01-01

    In this paper, the aerodynamic performance of two innovative bridge cable surfaces with concave fillets are examined and compared with traditional helical fillets. To this end, an extensive wind-tunnel test campaign was undertaken to measure the aerodynamic static force coefficients up to a Reyno......In this paper, the aerodynamic performance of two innovative bridge cable surfaces with concave fillets are examined and compared with traditional helical fillets. To this end, an extensive wind-tunnel test campaign was undertaken to measure the aerodynamic static force coefficients up...... to a Reynolds number of 3.2 x 105. The tests confirmed the results obtained from the preliminary tests performed by Kleissl and Georgakis (2013) on the prototype cable surfaces with the concave fillets. Despite a more than 100% increase of the fillet height compared to a traditional helical fillet profile...

  5. Preliminary evaluation capability for some two-dimensional groundwater contamination problems

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, R.W.; Schur, J.A.

    1978-06-01

    There are a variety of two-dimensional groundwater pollution problems where a preliminary evaluation of containment tansport is needed. A common difficulty in making this first assessment is the meager field data usually available. A preliminary evaluation capability has been developed for two-dimensional contamination problems that is consistent with the limited data initially available. Idealizations and simplifications have been introduced with special care so that worst-case final estimates will be provided. The preliminary evaluation results are produced using interactive computer programs that utilize self-help or coaching features for the user's convenience. The self-help programs aid the user by asking for the necessary input parameters and by guiding the user, in selecting the options needed to obtain the required results.

  6. PRELIMINARY PHARMACOGNOSTICAL AND PHYTOCHEMICAL EVALUATION OF ARGYREIA NERVOSA LEAF

    Directory of Open Access Journals (Sweden)

    A. Krishnaveni

    2011-02-01

    Full Text Available Traditionally used by the tribal of Rajasthan to prevent conception. Roots are used as appetizer, aphrodisiac, brain tonic, cardiotonic and to treat insanity and synovitis. Leaves, seeds preparations are used to treat epilepsy, diarrhea and nootropic. Leaf materials were collected, dried and coarsely powdered and were subjected to physiochemical constants, behavioral characters of the leaf powder with chemical reagents. Pharmacognostical studies include macroscopical, microscopical observations. Physical chemical constants such as ash values, extractive values, loss on drying, foreign organic matter were determined. Ash values include total ash; acid insoluble and water soluble ash were observed. Extractive values of powder with solvents such as petroleum ether, chloroform, ethyl actetae, ethanol and water were determined. Macroscopical characters help in identifying the leaf. Anatomical observations showed the presence of trichomes, upper and lower epidermal cells with rubiaceous stomata. Sclerenchyma fibers and acicular crystal were observed. The percentage of total ash values (4.3, 1.6 and3.94 % yield of petroleum ether, ethyl acetate, chloroform, ethanol and water showed 3.16,6.4,5.8,10.2 and 7.6% respectively. Preliminary phytochemical screening reported the presence of alkaloids, tannins, phenolic compounds, glycosides and flavanoids.The reported phytoconstitutents of the plant Argyreia nervosa may be responsible for the pharmacological activities. The results obtained add credit to the existing traditional information which will further increase the usage of this plant and provokes towards the investigation of the plant.

  7. Dedicated optoelectronic stochastic parallel processor for real-time image processing: motion-detection demonstration and design of a hybrid complementary-metal-oxide semiconductor- self-electro-optic-device-based prototype.

    Science.gov (United States)

    Cassinelli, A; Chavel, P; Desmulliez, M P

    2001-12-10

    We report experimental results and performance analysis of a dedicated optoelectronic processor that implements stochastic optimization-based image-processing tasks in real time. We first show experimental results using a proof-of-principle-prototype demonstrator based on standard silicon-complementary-metal-oxide-semiconductor (CMOS) technology and liquid-crystal spatial light modulators. We then elaborate on the advantages of using a hybrid CMOS-self-electro-optic-device-based smart-pixel array to monolithically integrate photodetectors and modulators on the same chip, providing compact, high-bandwidth intrachip optoelectronic interconnects. We have modeled the operation of the monolithic processor, clearly showing system-performance improvement.

  8. Synthesis, structural, electronic and linear electro-optical features of new quaternary Ag2Ga2SiS6 compound

    Science.gov (United States)

    Piasecki, M.; Myronchuk, G. L.; Parasyuk, O. V.; Khyzhun, O. Y.; Fedorchuk, A. O.; Pavlyuk, V. V.; Kozer, V. R.; Sachanyuk, V. P.; El-Naggar, A. M.; Albassam, A. A.; Jedryka, J.; Kityk, I. V.

    2017-02-01

    For the first time phase equilibria and phase diagram of the AgGaS2-SiS2 system were successfully explored by differential thermal and X-ray phase analysis methods. Crystal structure of low-temperature (LT) modification of Ag2Ga2SiS6 (LT- Ag2Ga2SiS6) was studied by X-ray powder method and it belongs to tetragonal space group I-42d, with unit cell parameters a=5.7164(4) Å, c=9.8023(7) Å, V=320.32(7) Å3. Additional details regarding the crystal structure exploration are available at the web page Fachinformationszentrum Karlsruhe. X-ray photoelectron core-level and valence-band spectra were measured for pristine LT- Ag2Ga2SiS6 crystal surface. In addition, the X-ray photoelectron valence-band spectrum of LT-Ag2Ga2SiS6 was matched on a common energy scale with the X-ray emission S Kβ1,3 and Ga Kβ2 bands, which give information on the energy distribution of the S 3p and Ga 4p states, respectively. The presented X-ray spectroscopy results indicate that the valence S p and Ga p atomic states contribute mainly to the upper and central parts of the valence band of LT-Ag2Ga2SiS6, respectively, with a less significant contribution also to other valence-band regions. Band gap energy was estimated by measuring the quantum energy in the spectral range of the fundamental absorption. We have found that energy gap Eg is equal to 2.35 eV at 300 K. LT-Ag2Ga2SiS6 is a photosensitive material and reveals two spectral maxima on the curve of spectral photoconductivity spectra at λmax1 =590 nm and λmax2 =860 nm. Additionally, linear electro-optical effect of LT-Ag2Ga2SiS6 for the wavelengths of a cw He-Ne laser at 1150 nm was explored.

  9. Super-Efficient Refrigerator Program (SERP) evaluation volume 2: Preliminary impact and market transformation assessment

    Energy Technology Data Exchange (ETDEWEB)

    Lee, A.D.; Conger, R.L.

    1996-08-01

    The Super Efficient Refrigerator Program (SERP) is a collaborative utility program intended to transform the market for energy-efficient and environmentally friendly refrigerators. It is one of the first examples of a large-scale {open_quotes}market transformation{close_quotes} energy efficiency program. This report documents the preliminary impact and market transformation evaluation of SERP ({open_quotes}the Program{close_quotes}). Pacific Northwest National Laboratory (PNNL) conducted this evaluation for the U.S. Department of Energy. This study focuses on the preliminary impact evaluation and market transformation assessment, but also presents limited process evaluation information. It is based on interviews with refrigerator dealers and manufacturers, interviews with utility participants, industry data, and information from the Program administrators. Results from this study complement those from prior process evaluation also conducted by PNNL. 42 refs., 5 figs., 4 tabs.

  10. Preliminary Technical and Legal Evaluation of Disposing of Nonhazardous Oil Field Waste into Salt Caverns

    Energy Technology Data Exchange (ETDEWEB)

    Ayers, Robert C.; Caudle, Dan; Elcock, Deborah; Raivel, Mary; Veil, John; and Grunewald, Ben

    1999-01-21

    This report presents an initial evaluation of the suitability, feasibility, and legality of using salt caverns for disposal of nonhazardous oil field wastes. Given the preliminary and general nature of this report, we recognize that some of our findings and conclusions maybe speculative and subject to change upon further research on this topic.

  11. Preliminary data for the 20 May 1974, simultaneous evaluation of remote sensors experiment. [water pollution monitoring

    Science.gov (United States)

    Johnson, R. W.; Batten, C. E.; Bowker, D. E.; Bressette, W. E.; Grew, G. W.

    1975-01-01

    Several remote sensors were simultaneously used to collect data over the tidal James River from Hopewell to Norfolk, Virginia. Sensors evaluated included the Multichannel-Ocean Color Sensor, multispectral scanners, and multispectral photography. Ground truth measurements and remotely sensed data are given. Preliminary analysis indicates that suspended sediment and concentrated industrial effluent are observable from all sensors.

  12. Description and Preliminary Training Evaluation of an Arc Welding Simulator. Research Report SRR 73-23.

    Science.gov (United States)

    Abrams, Macy L.; And Others

    A prototype arc welding training simulator was designed to provide immediate, discriminative feedback and the capacity for concentrated practice. Two randomly selected groups of welding trainees were compared to evaluate the simulator, one group being trained using the simulator and the other using conventional practice. Preliminary data indicated…

  13. In vitro tests to evaluate immunotoxicity: A preliminary study.

    NARCIS (Netherlands)

    Carfi', M; Gennari, A; Malerba, I; Corsini, E; Pallardy, M; Pieters, R; Loveren, Henk van; Vohr, H W; Hartung, T; Gribaldo, L

    2007-01-01

    The implementation of Registration, Evaluation and Authorisation of new and existing Chemicals (REACH) will increase the number of laboratory animals used, if alternative methods will not be available. In the meantime, REACH promotes the use of in vitro tests and, therefore, a set of appropriated al

  14. [Clinical diagnosis and standardized evaluation of borderline personality: preliminary report].

    Science.gov (United States)

    Chaine, F; Guelfi, J D; Monier, C; Brun, A; Seunevel, F

    1995-01-01

    A sample of 36 patients considered by French clinicians as suffering from a borderline personality disorder was evaluated using the International Personality Disorder Examination, the Diagnostic Interview for Borderline-Revised, and the Minnesota Multiphasic Personality Inventory. First, global descriptive analysis of the sample elicited the socio-demographic and standard clinical characteristics of the borderline individuals. After diagnostic evaluation, the sample appeared to be quite homogeneous with 25 of the 36 patients evaluated (69.5%) being defined as borderline by two of the three diagnostic systems: ICD 10, DSM III-R and Gunderson (15/36 = 41.5% of patients were defined as borderline by all three systems). It is the types of BL personality co-diagnoses which differentiated the BL subjects in the sample from those classically described in the international literature, since the most frequent personalities were the Dependent and Avoiding ones, not the Antisocial, Histrionic, Narcissistic or Schizotypic personalities of the DSM III-R. ICD 10 elicited the same significant prevalence of Anxious and Dependent personalities. Lastly, the patients diagnosed as borderline both by clinicians and by all diagnostic systems (forming the sample "core") were compared with the rest of the sample with regard to socio-demographic, clinical and diagnostic characteristics. A few hypotheses are proposed on the type of variables that may permit to discriminate between these two types of patients.

  15. Efficacy of oleuropein against UVB irradiation: preliminary evaluation.

    Science.gov (United States)

    Perugini, P; Vettor, M; Rona, C; Troisi, L; Villanova, L; Genta, I; Conti, B; Pavanetto, F

    2008-04-01

    Oleuropein, a phenolic compound derived from olive leaves and oil, is known to possess several biological properties, many of which may be attributed to its antioxidant and free radical-scavenging activities. Nevertheless, up to now, the cosmetic activity of this molecule has not been extensively investigated. The aim of this work was to evaluate the cosmetic properties of oleuropein against UVB-induced erythema. To this end, an emulsion and an emulgel containing oleuropein were prepared, applied and evaluated on healthy volunteers who had undergone UVB irradiation to investigate its protective and/or lenitive activity. Protective effect was assayed by application of topical preparations before irradiation and lenitive effect was evaluated after erythema induction. Vitamin E was used as the reference compound. Our study was carried out by using noninvasive techniques to assess specific skin parameters: barrier function, skin colour and microcirculation. Results clearly showed that oleuropein formulations highlighted lenitive efficacy by reducing erythema, transepidermal water loss and blood flow of about 22%, 35% and 30% respectively. The study allowed us to point out the lenitive property of oleuropein, opening the way to further trials to deepen our specific knowledge about this natural molecule, which could be used in association with other active ingredients in cosmetics to repair UV damages.

  16. National Evaluation of the Weatherization Assistance Program: Preliminary Evaluation Plan for Program Year 2006

    Energy Technology Data Exchange (ETDEWEB)

    Ternes, Mark P [ORNL; Schweitzer, Martin [ORNL; Tonn, Bruce Edward [ORNL; Schmoyer, Richard L [ORNL; Eisenberg, Joel Fred [ORNL

    2007-02-01

    federal, state, and local initiatives. For example, the use of computerized audits has increased, cooling and baseload measures have been added, weatherization approaches tailored to the unique construction characteristics of mobile homes have been developed, the weatherization of large multifamily buildings has expanded and become more sophisticated, the flexibility to improve 'energy-related' health and safety has been provided, and leveraging with utilities, other state programs, and owners of large multifamily buildings has increased considerably. The Department of Energy tasked ORNL with planning the new evaluation in light of its experience in conducting the previous national evaluation and the metaevaluations. This preliminary evaluation plan, developed by ORNL, documents how the new national evaluation will be performed. In the remaining portion of this section, the purpose and fundamental questions the evaluation will address are identified and how these questions were derived is discussed.

  17. Linear electro-optic properties of relaxor-based ferroelectric 0.24Pb(In1/2Nb1/2)O3-(0.76 − x)Pb(Mg1/3Nb2/3)O3-xPbTiO3 single crystals

    Science.gov (United States)

    Wu, Fengmin; Yang, Bin; Sun, Enwei; Liu, Gang; Tian, Hao; Cao, Wenwu

    2013-01-01

    Linear electro-optic properties of 0.24Pb(In1/2Nb1/2)O3-(0.76 − x)Pb(Mg1/3Nb2/3)O3-xPbTiO3 single crystals, with compositions in the rhombohedral, morphotropic phase boundary (MPB) and tetragonal phases, have been investigated. Very large effective electro-optic coefficient γc (204 pm/V) was observed in a crystal with the MPB composition when it is poled along [001]. The rhombohedral phase (x = 0.27 and 0.30) single crystals poled along [111] direction and tetragonal phase (x = 0.39) single crystal poled along [001] direction are in single domain, and their electro-optic coefficients (γc = 76, 94, and 43 pm/V for the crystals with x = 0.27, 0.30, and 0.39, respectively) were found to be much higher than that of traditional electro-optic single crystal LiNbO3 (γc = 19.9 pm/V). The electro-optic coefficients of the single crystal in the rhombohedral phase have excellent temperature stability in the experimental temperature range of 10–40 °C. The half-wave voltage Vπ was calculated to be much lower (less than 1000 V) than that of LiNbO3 single crystal (2800 V). These superior properties make the ternary relaxor-PT single crystals very promising for electro-optic modulation applications. PMID:23922449

  18. Linear electro-optic properties of relaxor-based ferroelectric 0.24Pb(In1/2Nb1/2)O3-(0.76 - x)Pb(Mg1/3Nb2/3)O3-xPbTiO3 single crystals.

    Science.gov (United States)

    Wu, Fengmin; Yang, Bin; Sun, Enwei; Liu, Gang; Tian, Hao; Cao, Wenwu

    2013-07-14

    Linear electro-optic properties of 0.24Pb(In1/2Nb1/2)O3-(0.76 - x)Pb(Mg1/3Nb2/3)O3-xPbTiO3 single crystals, with compositions in the rhombohedral, morphotropic phase boundary (MPB) and tetragonal phases, have been investigated. Very large effective electro-optic coefficient [Formula: see text] (204 pm/V) was observed in a crystal with the MPB composition when it is poled along [001]. The rhombohedral phase (x = 0.27 and 0.30) single crystals poled along [111] direction and tetragonal phase (x = 0.39) single crystal poled along [001] direction are in single domain, and their electro-optic coefficients ([Formula: see text] = 76, 94, and 43 pm/V for the crystals with x = 0.27, 0.30, and 0.39, respectively) were found to be much higher than that of traditional electro-optic single crystal LiNbO3 ([Formula: see text] = 19.9 pm/V). The electro-optic coefficients of the single crystal in the rhombohedral phase have excellent temperature stability in the experimental temperature range of 10-40 °C. The half-wave voltage [Formula: see text] was calculated to be much lower (less than 1000 V) than that of LiNbO3 single crystal (2800 V). These superior properties make the ternary relaxor-PT single crystals very promising for electro-optic modulation applications.

  19. 舰船光电对抗中烟幕遮蔽与激光引偏的配合作战研究%Cooperative Deployment of Smoke Screen and Laser Seduction for Shipborne Electro-Optical Countermeasure

    Institute of Scientific and Technical Information of China (English)

    杨涛; 陆海剑

    2011-01-01

    In view of the characteristics of smoke screen and laser seduction for shipborne electro-optical countermeasure system, cooperative deployment of smoke screen and laser seduction against semi-autonomous laser guidance weapons is proposed, including analyzing the operation condition, flow of work and supplementary factors in various scenarios. The advantages and disadvantages of this cooperative deployment in different scenarios are presented as well It is shown that cooperative deployment of multiple countermeasures is critical to improve the efficiency of electro-optical countermeasure system.%通过分析舰船光电对抗作战中烟幕干扰和激光引偏干扰的特点,提出了烟幕遮蔽和激光引偏在对抗半自主激光制导武器时配合使用的作战样式,分析了各种作战样式的使用条件、工作流程和配合要素,以及作战样式的优势与不足,指出了多种干扰手段配合作战是发挥光电对抗系统综合对抗效能的关键.

  20. Preliminary field evaluation of high efficiency steel filters

    Energy Technology Data Exchange (ETDEWEB)

    Bergman, W.; Larsen, G.; Lopez, R. [Lawrence Livermore National Laboratory, CA (United States)] [and others

    1995-02-01

    We have conducted an evaluation of two high efficiency steel filters in the exhaust of an uranium oxide grit blaster at the Y-12 Plant in Oak Ridge Tennessee. The filters were installed in a specially designed filter housing with a reverse air-pulse cleaning system for automatically cleaning the filters in-place. Previous tests conducted on the same filters and housing at LLNL under controlled conditions using Arizona road dust showed good cleanability with reverse air pulses. Two high efficiency steel filters, containing 64 pleated cartridge elements housed in the standard 2` x 2` x 1` HEPA frame, were evaluated in the filter test housing using a 1,000 cfm slip stream containing a high concentration of depleted uranium oxide dust. One filter had the pleated cartridges manufactured to our specifications by the Pall Corporation and the other by Memtec Corporation. Test results showed both filters had a rapid increase in pressure drop with time, and reverse air pulses could not decrease the pressure drop. We suspected moisture accumulation in the filters was the problem since there were heavy rains during the evaluations, and the pressure drop of the Memtec filter decreased dramatically after passing clean, dry air through the filter and after the filter sat idle for one week. Subsequent laboratory tests on a single filter cartridge confirmed that water accumulation in the filter was responsible for the increase in filter pressure drop and the inability to lower the pressure drop by reverse air pulses. No effort was made to identify the source of the water accumulation and correct the problem because the available funds were exhausted.