WorldWideScience

Sample records for preliminary autodyn simulations

  1. Simulation of blast action on civil structures using ANSYS Autodyn

    Science.gov (United States)

    Fedorova, N. N.; Valger, S. A.; Fedorov, A. V.

    2016-10-01

    The paper presents the results of 3D numerical simulations of shock wave spreading in cityscape area. ANSYS Autodyne software is used for the computations. Different test cases are investigated numerically. On the basis of the computations, the complex transient flowfield structure formed in the vicinity of prismatic bodies was obtained and analyzed. The simulation results have been compared to the experimental data. The ability of two numerical schemes is studied to correctly predict the pressure history in several gauges placed on walls of the obstacles.

  2. Numerical simulation of rock cutting using 2D AUTODYN

    Science.gov (United States)

    Woldemichael, D. E.; Rani, A. M. Abdul; Lemma, T. A.; Altaf, K.

    2015-12-01

    In a drilling process for oil and gas exploration, understanding of the interaction between the cutting tool and the rock is important for optimization of the drilling process using polycrystalline diamond compact (PDC) cutters. In this study the finite element method in ANSYS AUTODYN-2D is used to simulate the dynamics of cutter rock interaction, rock failure, and fragmentation. A two-dimensional single PDC cutter and rock model were used to simulate the orthogonal cutting process and to investigate the effect of different parameters such as depth of cut, and back rake angle on two types of rocks (sandstone and limestone). In the simulation, the cutting tool was dragged against stationary rock at predetermined linear velocity and the depth of cut (1,2, and 3 mm) and the back rake angles(-10°, 0°, and +10°) were varied. The simulation result shows that the +10° back rake angle results in higher rate of penetration (ROP). Increasing depth of cut leads to higher ROP at the cost of higher cutting force.

  3. Comparative study of autodyne and heterodyne laser interferometry for imaging

    CERN Document Server

    Lacot, Eric; Roussely, Grégoire; Hugon, Olivier; De Chatellus, Hugues Guillet

    2014-01-01

    For given laser output power, object under investigation and photodiode noise level, we have theoretically compared the signal to noise ratio (SNR) of a heterodyne scanning imager based on a Michelson interferometer and of an autodyne setup based on the Laser Optical Feedback Imaging (LOFI) technique. In both cases, the image is obtained point by point. In the heterodyne configuration, the beating between the reference beam and the signal beam is realized outside the laser cavity (i.e. directly on the detector), while in the autodyne configuration, the wave beating takes place inside the laser cavity and therefore is indirectly detected. In the autodyne configuration, where the laser relaxation oscillations play a leading role, we have compared 1D scans obtained by numerical simulations with different lasers dynamical parameters. Finally we have determined the best laser for LOFI applications and the experimental conditions for which the LOFI detection setup (autodyne interferometer) is competitive comparing ...

  4. Peculiarities of Noise Characteristics of Autodynes Under Strong External Feedback

    Science.gov (United States)

    Noskov, V. Ya.; Ignatkov, K. A.

    2014-04-01

    Results are presented of a quasistatic analysis of the noise characteristics of an autodyne operating under the action of its own reflected radiation with its own internal noise taken into account. Periodic non-stationarity of the root-mean-square value of the phase, frequency, and amplitude noise levels is established, which is manifested when the distance to the reflecting object is varied. It is shown that the given phenomenon is observed upon increase of the level of reflected radiation, when the magnitude of the external feedback parameter of the autodyne system becomes comparable to unity. Results of our own experimental studies of a hybrid-integrated oscillator based on a Gunn diode, and also results published in other works for avalanche transit-time diode oscillators and autodynes based on laser diodes, have confirmed the conclusions of our theoretical analysis.

  5. Application of laser autodyne for vibration assessment of tympanic membrane

    Directory of Open Access Journals (Sweden)

    Skripal A.V.

    2011-12-01

    Full Text Available Research is devoted to assessing the state of the middle ear structures by usage of modern nanotechnology methods. The history of the problem, various ancient and modern methods for studying the mobility of the middle ear structures have been described. The results of the research of eardrum movements by laser autodyne and their value in differential diagnosis of ear diseases have been presented. The research goal is to assess vibrations of middle ear structures by modern nanotechnological techniques. Materials: The study included 207 persons, divided into groups of healthy individuals and patients with sensorineural deafness, otosclerosis, adhesive otitis and tubootitis. Results: Exact frequency response vibration patterns of the middle ear and tympanic membrane have been obtained. Measurements have been made in open sound field in normal ears and ears with various pathology of middle and inner ear. The value of this method in differential diagnosis of ear diseases has been investigated. Conclusion: The use of laser autodyne for measuring middle ear structures vibration is a perspective and objective method of assessing auditory function. It is very necessary in modern otolaryngology for differential diagnosis of hearing pathology

  6. An analysis of the autodyne effect of oscillators with linear frequency modulation

    Science.gov (United States)

    Votoropin, S. D.; Noskov, V. Ya.; Smolskiy, S. M.

    2008-06-01

    General equations are obtained for the autodyne response in the case of an arbitrary frequency modulation both over the active element bias circuit and voltage variation on the voltage-dependent capacitor (varicap). The results of investigation of an autodyne oscillator with linear frequency modulation following the antisymmetric and symmetric saw-tooth function are presented, with the oscillator being affected by its own reflected radiation. Special features of self-oscillations of such autodynes are considered, with the aim to improve their characteristics and extend the functional capabilities of short-range autodyne radars. The experimental results obtained for the TIGEL 08FM oscillator module manufactured using a hybrid-integral technology on the basis of a mm-range Gunn diode are reported.

  7. Autodyne characteristics of stabilized UHF-oscillators at a strong reflected signal

    Directory of Open Access Journals (Sweden)

    Noskov V. Ya.

    2011-11-01

    Full Text Available Calculations and examinations of phase, amplitude, frequency and amplitude-frequency characteristics are fulfilled for the autodyne system stabilized by the external high-Q cavity as well as spectral characteristics under condition of exact and non-exact cavity tuning and the variations of distance to reflector. The distinguished peculiarities of the autodyne response at the small and large reflected signal are described. Experimental research results are discussed fulfilled on an example of the hybrid-integrated oscillator on Gunn diode of 8-mm-range, which confirm qualitatively the theoretic results.

  8. Influence of inherent parameter of stabilized UHF oscillators on autodyne response formation at a strong reflected signal

    Directory of Open Access Journals (Sweden)

    Noskov V. Ya.

    2011-08-01

    Full Text Available Results of an autodyne response analysis in UHF oscillators stabilized by the external high-Q cavity in the case of the strong signal when the reflected wave amplitude commen-surable with the own oscillation amplitude. Coupling between the basic operation cavity and the stabilizing cavity is implemented as a pass-reflecting filter with a resistive bond. Key relations are obtained, which describe the autodyne response to the own re-reflected radiation from a target. The load and oscillating system influence on autodyne response formation is fulfilled.

  9. Experimental comparison of autodyne and heterodyne laser interferometry using a Nd:YVO4 microchip laser

    CERN Document Server

    Jacquin, Olivier; Glastre, Wilfried; Hugon, Olivier; De Chatellus, Hugues Guillet

    2012-01-01

    Using a Nd:YVO4 microchip laser with a relaxation frequency in the megahertz range, we have experimentally compared a heterodyne interferometer based on a Michelson configuration with an autodyne interferometer based on the laser optical feedback imaging (LOFI) method regarding their signal to noise ratios. In the heterodyne configuration, the beating between the reference beam and the signal beam is realized outside the laser cavity while in the autodyne configuration, the wave beating takes place inside the laser cavity and the relaxation oscillations of the laser intensity then play an important part. For a given laser output power, object under investigation and detection noise level, we have determined the amplification gain of the LOFI interferometer compared to the heterodyne interferometer. LOFI interferometry is demonstrated to show higher performances than heterodyne interferometry for a wide range of laser power and detection level of noise. The experimental results are in good agreement with the t...

  10. Development of a Numerical Model for an Expanding Tube with Linear Explosive Using AUTODYN

    Directory of Open Access Journals (Sweden)

    Mijin Choi

    2014-01-01

    Full Text Available Pyrotechnic devices have been employed in satellite launch vehicle missions, generally for the separation of structural subsystems such as stage and satellite separation. Expanding tubes are linear explosives enclosed by an oval steel tube and have been widely used for pyrotechnic joint separation systems. A numerical model is proposed for the prediction of the proper load of an expanding tube using a nonlinear dynamic analysis code, AUTODYN 2D and 3D. To compute a proper core load, numerical models of the open-ended steel tube and mild detonating tube encasing a high explosive were developed and compared with experimental results. 2D and 3D computational results showed good correlation with ballistic test results. The model will provide more flexibility in expanding tube design, leading to economic benefits in the overall expanding tube development procedure.

  11. Time domain simulations of preliminary breakdown pulses in natural lightning

    Science.gov (United States)

    Carlson, B E; Liang, C; Bitzer, P; Christian, H

    2015-01-01

    Lightning discharge is a complicated process with relevant physical scales spanning many orders of magnitude. In an effort to understand the electrodynamics of lightning and connect physical properties of the channel to observed behavior, we construct a simulation of charge and current flow on a narrow conducting channel embedded in three-dimensional space with the time domain electric field integral equation, the method of moments, and the thin-wire approximation. The method includes approximate treatment of resistance evolution due to lightning channel heating and the corona sheath of charge surrounding the lightning channel. Focusing our attention on preliminary breakdown in natural lightning by simulating stepwise channel extension with a simplified geometry, our simulation reproduces the broad features observed in data collected with the Huntsville Alabama Marx Meter Array. Some deviations in pulse shape details are evident, suggesting future work focusing on the detailed properties of the stepping mechanism. Key Points Preliminary breakdown pulses can be reproduced by simulated channel extension Channel heating and corona sheath formation are crucial to proper pulse shape Extension processes and channel orientation significantly affect observations PMID:26664815

  12. Time domain simulations of preliminary breakdown pulses in natural lightning.

    Science.gov (United States)

    Carlson, B E; Liang, C; Bitzer, P; Christian, H

    2015-06-16

    Lightning discharge is a complicated process with relevant physical scales spanning many orders of magnitude. In an effort to understand the electrodynamics of lightning and connect physical properties of the channel to observed behavior, we construct a simulation of charge and current flow on a narrow conducting channel embedded in three-dimensional space with the time domain electric field integral equation, the method of moments, and the thin-wire approximation. The method includes approximate treatment of resistance evolution due to lightning channel heating and the corona sheath of charge surrounding the lightning channel. Focusing our attention on preliminary breakdown in natural lightning by simulating stepwise channel extension with a simplified geometry, our simulation reproduces the broad features observed in data collected with the Huntsville Alabama Marx Meter Array. Some deviations in pulse shape details are evident, suggesting future work focusing on the detailed properties of the stepping mechanism. Preliminary breakdown pulses can be reproduced by simulated channel extension Channel heating and corona sheath formation are crucial to proper pulse shape Extension processes and channel orientation significantly affect observations.

  13. Time domain simulations of preliminary breakdown pulses in natural lightning

    CERN Document Server

    Carlson, B E; Bitzer, P; Christian, H

    2016-01-01

    Lightning discharge is a complicated process with relevant physical scales spanning many orders of magnitude. In an effort to understand the electrodynamics of lightning and connect physical properties of the channel to observed behavior, we construct a simulation of charge and current flow on a narrow conducting channel embedded in three-dimensional space with the time domain electric field integral equation, the method of moments, and the thin-wire approximation. The method includes approximate treatment of resistance evolution due to lightning channel heating and the corona sheath of charge surrounding the lightning channel. Focusing our attention on preliminary breakdown in natural lightning by simulating stepwise channel extension with a simplified geometry, our simulation reproduces the broad features observed in data collected with the Huntsville Alabama Marx Meter Array. Some deviations in pulse shape details are evident, suggesting future work focusing on the detailed properties of the stepping mecha...

  14. Preliminary AD-Horn Thermomechanical and Electrodynamic Simulations

    CERN Document Server

    AUTHOR|(CDS)2095747; Horvath, David; Calviani, Marco

    2016-01-01

    As part of the Antiproton Decelerator (AD) target area consolidation activities planned for LS2, it has been necessary to perform a comprehensive study of the thermo-structural behaviour of the AD magnetic horn during operation, in order to detail specific requirements for the upgrade projects and testing procedures. The present work illustrates the preliminary results of the finite element analysis carried out to evaluate the thermal and structural behaviour of the device, as well as the methodology used to model and solve the thermomechanical and electrodynamic simulations performed in the AD magnetic horn.

  15. Electronic Warfare M-on-N Digital Simulation Logging Requirements and HDF5: A Preliminary Analysis

    Science.gov (United States)

    2017-04-12

    E. Jarvis Electronic Warfare M-on- N Digital Simulation Logging Requirements and HDF5: A Preliminary Analysis Advanced Techniques Branch Tactical...12-04-2017 NRL Memorandum Report Electronic Warfare M-on- N Digital Simulation Logging Requirements and HDF5: A Preliminary Analysis Donald E...ELECTRONIC WARFARE M-ON- N DIGITAL SIMULATION LOGGING REQUIREMENTS AND HDF5: A PRELIMINARY ANALYSIS 1. INTRODUCTION HDF5 technology [Folk] has been

  16. Penetration Evaluation of Explosively Formed Projectiles Through Air and Water Using Insensitive Munition: Simulative and Experimental Studies

    National Research Council Canada - National Science Library

    M. Ahmed; A. Q. Malik; S. A. Rofi; Z. X. Huang

    2016-01-01

    The process of formation, flying, penetration of explosively-formed projectiles (EFP) and the effect of water on performance of the charge for underwater applications is simulated by Ansysis Autodyn 2D-Hydro code...

  17. Description and Preliminary Training Evaluation of an Arc Welding Simulator. Research Report SRR 73-23.

    Science.gov (United States)

    Abrams, Macy L.; And Others

    A prototype arc welding training simulator was designed to provide immediate, discriminative feedback and the capacity for concentrated practice. Two randomly selected groups of welding trainees were compared to evaluate the simulator, one group being trained using the simulator and the other using conventional practice. Preliminary data indicated…

  18. Simulation of diurnal thermal energy storage systems: Preliminary results

    Science.gov (United States)

    Katipamula, S.; Somasundaram, S.; Williams, H. R.

    1994-12-01

    This report describes the results of a simulation of thermal energy storage (TES) integrated with a simple-cycle gas turbine cogeneration system. Integrating TES with cogeneration can serve the electrical and thermal loads independently while firing all fuel in the gas turbine. The detailed engineering and economic feasibility of diurnal TES systems integrated with cogeneration systems has been described in two previous PNL reports. The objective of this study was to lay the ground work for optimization of the TES system designs using a simulation tool called TRNSYS (TRaNsient SYstem Simulation). TRNSYS is a transient simulation program with a sequential-modular structure developed at the Solar Energy Laboratory, University of Wisconsin-Madison. The two TES systems selected for the base-case simulations were: (1) a one-tank storage model to represent the oil/rock TES system; and (2) a two-tank storage model to represent the molten nitrate salt TES system. Results of the study clearly indicate that an engineering optimization of the TES system using TRNSYS is possible. The one-tank stratified oil/rock storage model described here is a good starting point for parametric studies of a TES system. Further developments to the TRNSYS library of available models (economizer, evaporator, gas turbine, etc.) are recommended so that the phase-change processes is accurately treated.

  19. Simulation of diurnal thermal energy storage systems: Preliminary results

    Energy Technology Data Exchange (ETDEWEB)

    Katipamula, S.; Somasundaram, S. [Pacific Northwest Lab., Richland, WA (United States); Williams, H.R. [Univ. of Alaska, Fairbanks, AK (United States). Dept. of Mechanical Engineering

    1994-12-01

    This report describes the results of a simulation of thermal energy storage (TES) integrated with a simple-cycle gas turbine cogeneration system. Integrating TES with cogeneration can serve the electrical and thermal loads independently while firing all fuel in the gas turbine. The detailed engineering and economic feasibility of diurnal TES systems integrated with cogeneration systems has been described in two previous PNL reports. The objective of this study was to lay the ground work for optimization of the TES system designs using a simulation tool called TRNSYS (TRaNsient SYstem Simulation). TRNSYS is a transient simulation program with a sequential-modular structure developed at the Solar Energy Laboratory, University of Wisconsin-Madison. The two TES systems selected for the base-case simulations were: (1) a one-tank storage model to represent the oil/rock TES system, and (2) a two-tank storage model to represent the molten nitrate salt TES system. Results of the study clearly indicate that an engineering optimization of the TES system using TRNSYS is possible. The one-tank stratified oil/rock storage model described here is a good starting point for parametric studies of a TES system. Further developments to the TRNSYS library of available models (economizer, evaporator, gas turbine, etc.) are recommended so that the phase-change processes is accurately treated.

  20. Simulating lightning into the RAMS model: implementation and preliminary results

    Directory of Open Access Journals (Sweden)

    S. Federico

    2014-05-01

    Full Text Available This paper shows the results of a tailored version of a previously published methodology, designed to simulate lightning activity, implemented into the Regional Atmospheric Modeling System (RAMS. The method gives the flash density at the resolution of the RAMS grid-scale allowing for a detailed analysis of the evolution of simulated lightning activity. The system is applied in detail to two case studies occurred over the Lazio Region, in Central Italy. Simulations are compared with the lightning activity detected by the LINET network. The cases refer to two thunderstorms of different intensity. Results show that the model predicts reasonably well both cases and that the lightning activity is well reproduced especially for the most intense case. However, there are errors in timing and positioning of the convection, whose magnitude depends on the case study, which mirrors in timing and positioning errors of the lightning distribution. To assess objectively the performance of the methodology, standard scores are presented for four additional case studies. Scores show the ability of the methodology to simulate the daily lightning activity for different spatial scales and for two different minimum thresholds of flash number density. The performance decreases at finer spatial scales and for higher thresholds. The comparison of simulated and observed lighting activity is an immediate and powerful tool to assess the model ability to reproduce the intensity and the evolution of the convection. This shows the importance of the use of computationally efficient lightning schemes, such as the one described in this paper, in forecast models.

  1. Preliminary Modeling and Simulation Study on Olfactory Cell Sensation

    Science.gov (United States)

    Zhou, Jun; Yang, Wei; Chen, Peihua; Liu, Qingjun; Wang, Ping

    2009-05-01

    This paper introduced olfactory sensory neuron's whole-cell model with a concrete voltage-gated ionic channels and simulation. Though there are many models in olfactory sensory neuron and olfactory bulb, it remains uncertain how they express the logic of olfactory information processing. In this article, the olfactory neural network model is also introduced. This model specifies the connections among neural ensembles of the olfactory system. The simulation results of the neural network model are consistent with the observed olfactory biological characteristics such as 1/f-type power spectrum and oscillations.

  2. Large Eddy Simulation of isothermal cruciform jet flow: Preliminary results

    Directory of Open Access Journals (Sweden)

    B.T. Kannan

    2016-09-01

    Full Text Available The present work is a numerical study of a turbulent isothermal jet issuing from cruciform nozzle into still air at a high Reynolds number of 1.7 × 105. The numerical simulation was carried out by using open source CFD tool OpenFOAM®. Three-dimensional cuboid shaped domain was used to simulate the unsteady turbulent flow field. The simulation was carried out by solving the filtered Navier–Stokes equations along with Smagorinsky sub-grid scale model. The Large Eddy Simulation (LES solutions are compared with experimental data for validation of the jet flow physics. The flow field of turbulent jet from cruciform nozzle are described in terms of inverse mean axial velocity decay and visualizations. The vortical structures are visualized using iso-surface contours of vorticity magnitude. The vortical structures develop from the cruciform nozzle is significantly different from axisymmetric nozzles. The vortical structures show changes in shape as they move downstream from the nozzle. The cruciform jet shows complex vorticity dynamics in the near field region.

  3. Comparison of Simulations of Preliminary Breakdown to Observations from the Huntsville Alabama Marx Meter Array

    Science.gov (United States)

    Carlson, B. E.; Liang, C.; Bitzer, P. M.; Christian, H. J., Jr.

    2014-12-01

    Preliminary breakdown pulses in electric field change records are thought to be produced by sudden extensions of the lightning channel. We present detailed time domain electrodynamic simulations of extension of an existing lightning leader channel due to heating processes and compare the results to observations of a natural cloud-to-ground lightning discharge made with the Huntsville Alabama Marx Meter Array (HAMMA) at a variety of locations near the discharge. Varying the geometry and parameters of the simulations in an attempt to reproduce the data allows us to constrain the directionality and physical properties of the channel. We simulate a variety of leader step phenomena, including uniform heating over the entire step, connection with a space leader, and dart leader propagation onto a preconditioned channel. Results support the notion of impulsive channel extension as the mechanism for preliminary breakdown and shed light on the mechanics of the process.

  4. Preliminary Simulation of the Corrosion Rate of Archaeological Glass

    Energy Technology Data Exchange (ETDEWEB)

    Steefel, Carl

    2014-01-06

    In this study, we make use of a micro-continuum modeling approach (the Kinetic-Microscopic-Continuum Model or K{micro}C model) to capture the spatial distribution and identity of reaction products developing over time as a result of the archaeological glass corrosion, while also matching the time scales of alteration where possible. Since the glass blocks sat on the Mediterranean seafloor for 1800 years, the physical and chemical boundary conditions are largely constant. We focus on a fracture within the glass block identified by Verney-Carron et al. (2008) and simulate it as a 1D system, with a fixed concentration (Dirichlet) boundary corresponding to the interior of the fracture.

  5. A Preliminary Real-Time and Realistic Simulation Environment for Percutaneous Coronary Intervention

    Directory of Open Access Journals (Sweden)

    Jianhuang Wu

    2015-01-01

    Full Text Available Percutaneous coronary intervention (PCI is a minimally invasive surgery procedure that is widely used in the treatment of coronary artery disease. This procedure requires interventional cardiologists to have high proficiency and therefore demands an extensive training period in order to ensure successful surgical outcome. In this paper, a realistic and real-time interactive simulator for training PCI procedure is presented. A set of new approaches for core simulation components is devised and integrated into the simulator. Trainees can interact with the virtual simulation environment with real instruments and essential maneuvers encountered in real PCI procedure. Although presently targeted at PCI, our simulator could be easily extended to mimic the necessities of any vascular interventional radiology procedures by updating vascular anatomy. Preliminary validation of the proposed physical model of instruments is conducted on vascular phantom to demonstrate its performance and effectiveness.

  6. Preliminary result of a three dimensional numerical simulation of cloud formation over a cooling pond

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, T.

    1978-01-01

    Cooling ponds receive large amounts of waste heat from industrial sources and release the heat to the atmosphere. These large area sources of warm and moist air may have significant inadvertent effects. This paper is a preliminary step in the development of a method for estimating the perturbations in the atmosphere produced by a cooling pond. A three-dimensional numerical model based on turbulence second-moment closure equations and Gaussian cloud relations has been developed. A simplified version of the model, in which only turbulent energy and length-scale equations are solved prognostically, is used. Numerical simulations are conducted using as boundary conditions the data from a cooling pond study conducted in northern Illinois during the winter of 1976-1977. Preliminary analyses of these simulations indicate that formation of clouds over a cooling pond is sensitive to the moisture content in the ambient atmosphere.

  7. RHF RELAP5 model and preliminary loss-of-offsite-power simulation results for LEU conversion

    Energy Technology Data Exchange (ETDEWEB)

    Licht, J. R. [Argonne National Laboratory (ANL), Argonne, IL (United States). Nuclear Engineering Div.; Bergeron, A. [Argonne National Laboratory (ANL), Argonne, IL (United States). Nuclear Engineering Div.; Dionne, B. [Argonne National Laboratory (ANL), Argonne, IL (United States). Nuclear Engineering Div.; Thomas, F. [Institut Laue-Langevin (ILL), Grenoble (Switzerland). RHF Reactor Dept.

    2014-08-01

    The purpose of this document is to describe the current state of the RELAP5 model for the Institut Laue-Langevin High Flux Reactor (RHF) located in Grenoble, France, and provide an update to the key information required to complete, for example, simulations for a loss of offsite power (LOOP) accident. A previous status report identified a list of 22 items to be resolved in order to complete the RELAP5 model. Most of these items have been resolved by ANL and the RHF team. Enough information was available to perform preliminary safety analyses and define the key items that are still required. Section 2 of this document describes the RELAP5 model of RHF. The final part of this section briefly summarizes previous model issues and resolutions. Section 3 of this document describes preliminary LOOP simulations for both HEU and LEU fuel at beginning of cycle conditions.

  8. RHF RELAP5 Model and Preliminary Loss-Of-Offsite-Power Simulation Results for LEU Conversion

    Energy Technology Data Exchange (ETDEWEB)

    Licht, J. R. [Argonne National Laboratory (ANL), Argonne, IL (United States). Nuclear Engineering Div.; Bergeron, A. [Argonne National Laboratory (ANL), Argonne, IL (United States). Nuclear Engineering Div.; Dionne, B. [Argonne National Laboratory (ANL), Argonne, IL (United States). Nuclear Engineering Div.; Thomas, F. [Institut Laue-Langevin (ILL), Grenoble (Switzerland). RHF Reactor Dept.

    2014-08-01

    The purpose of this document is to describe the current state of the RELAP5 model for the Institut Laue-Langevin High Flux Reactor (RHF) located in Grenoble, France, and provide an update to the key information required to complete, for example, simulations for a loss of offsite power (LOOP) accident. A previous status report identified a list of 22 items to be resolved in order to complete the RELAP5 model. Most of these items have been resolved by ANL and the RHF team. Enough information was available to perform preliminary safety analyses and define the key items that are still required. Section 2 of this document describes the RELAP5 model of RHF. The final part of this section briefly summarizes previous model issues and resolutions. Section 3 of this document describes preliminary LOOP simulations for both HEU and LEU fuel at beginning of cycle conditions.

  9. K8型单层球面网壳基于AUTODYN的外爆响应分析%RESPONSES OF SINGLE-LAYER RETICULATED DOMES SUBJECTED TO EXTERNAL BLAST LOADING USING AUTODYN

    Institute of Scientific and Technical Information of China (English)

    杨帆; 支旭东; 范峰

    2015-01-01

    The dynamic responses of single-layer reticulated domes are analyzed through the explicit dynamic finite element software AUTODYN.The load is applied using the FSI method,and the material is adopted using a multi-segment linear model for steel.First,the accuracy is verified by analyzing near-field and far-field explosions.Then the responses of a 20m span reticulated dome are obtained under external blast loading,including the loading spread,change in maximum nodal displacement,and development of plastic members.The laws governing structural response are researched,accounting for the mass of TNT,explosion distance,and explosion height.The results of numerical simulations indicate that AUTODYN can be used to analyze near-field and far-field explosions;the reticulated dome experiences two main shock wave loadings under external blast loading and the maximum nodal displacement occurs at the first shock wave loading;the plasticity development of structural members ends at 0.05 seconds;the structural responses strengthen with the increase of TNT mass and the explosion height,but weaken with the increase of explosion distance.%该文采用显式动力有限元软件AUTODYN对K8型单层球面网壳在外爆荷载下的动态响应进行了研究.数值模拟中采用流固耦合方法施加荷载,钢材采用多段线性模型,首先验证了AUTODYN进行近场爆炸分析和远场爆炸分析的准确性;考察了跨度为20 m的网壳结构在外爆荷载下的荷载传播规律、最大节点位移变化规律以及塑性杆件发展规律,考察了跨度为40 m网壳结构在TNT质量、炸点距离以及炸点高度参数变化下的结构响应规律.数值分析的结果表明:AUTODYN具备准确进行近场爆炸和远场爆炸分析的能力;单层球面网壳在外爆荷载下主要经历两次冲击波荷载,最大节点位移出现在第一次冲击荷载作用时,结构杆件的塑性发展在0.05 s后基本结束;网壳结构的响应随TNT质量增加和

  10. Simulation of the preliminary General Electric SP-100 space reactor concept using the ATHENA computer code

    Science.gov (United States)

    Fletcher, C. D.

    The capability to perform thermal-hydraulic analyses of a space reactor using the ATHENA computer code is demonstrated. The fast reactor, liquid-lithium coolant loops, and lithium-filled heat pipes of the preliminary General electric SP-100 design were modeled with ATHENA. Two demonstration transient calculations were performed simulating accident conditions. Calculated results are available for display using the Nuclear Plant Analyzer color graphics analysis tool in addition to traditional plots. ATHENA-calculated results appear reasonable, both for steady state full power conditions, and for the two transients. This analysis represents the first known transient thermal-hydraulic simulation using an integral space reactor system model incorporating heat pipes.

  11. Preliminary Computational Fluid Dynamics (CFD) Simulation of EIIB Push Barge in Shallow Water

    Science.gov (United States)

    Beneš, Petr; Kollárik, Róbert

    2011-12-01

    This study presents preliminary CFD simulation of EIIb push barge in inland conditions using CFD software Ansys Fluent. The RANSE (Reynolds Averaged Navier-Stokes Equation) methods are used for the viscosity solution of turbulent flow around the ship hull. Different RANSE methods are used for the comparison of their results in ship resistance calculations, for selecting the appropriate and removing inappropriate methods. This study further familiarizes on the creation of geometrical model which considers exact water depth to vessel draft ratio in shallow water conditions, grid generation, setting mathematical model in Fluent and evaluation of the simulations results.

  12. The Geoengineering Model Intercomparison Project Phase 6 (GeoMIP6: simulation design and preliminary results

    Directory of Open Access Journals (Sweden)

    B. Kravitz

    2015-06-01

    simulations, and has been expanded to address several further important topics, including key uncertainties in extreme events, the use of geoengineering as part of a portfolio of responses to climate change, and the relatively new idea of cirrus cloud thinning to allow more longwave radiation to escape to space. We discuss experiment designs, as well as the rationale for those designs, showing preliminary results from individual models when available. We also introduce a new feature, called the GeoMIP Testbed, which provides a platform for simulations that will be performed with a few models and subsequently assessed to determine whether the proposed experiment designs will be adopted as core (Tier 1 GeoMIP experiments. This is meant to encourage various stakeholders to propose new targeted experiments that address their key open science questions, with the goal of making GeoMIP more relevant to a broader set of communities.

  13. Simulation of Droplet Formation, Ejection, Spread, and Preliminary Designof Nozzle for Direct Ceramic Inkjet Printing

    Directory of Open Access Journals (Sweden)

    A. Venumadhav Reddy

    2007-03-01

    Full Text Available Recent advances in drop-on-demand (DOD-type inkjet printing techniques have increasedresearch activities in the area of direct ceramic inkjet printing. In an attempt to develop a ceramicinkjet printer for the manufacture of ceramic components with their sizes in micro scale, theformation of ceramic ink droplet (ethyl alcohol loaded with different volume fractions of aluminaparticles and its spread from a reservoir using piezoelectric actuation are simulated. The propertiesof the ceramic ink are taken from the data reported in literature. The simulations were performedwith computational fluid dynamics software (CFD-ACE+, CFDRC. This study gives details ofthe interaction among different physical phenomena that contribute to the droplet formation andejection process. The results from this study are being used for a preliminary design of nozzleand for the preparation of ceramic inks to achieve the desired droplet characteristics.

  14. Modeling and Simulation of Ceramic Arrays to Improve Ballistic Performance (Briefing charts)

    Science.gov (United States)

    2014-02-28

    center impact DOP can on be achieved If at a gap size of 0.508 mm -In simulation the adhesive layer improves the ballistic efficiency of the target...Projectile, 762x39 PS Projectile, SPH, Aluminum 5083, SiC, DoP Expeminets, AutoDyn Sin 16. SECURITY CLASSIFICATION OF: UU a. REPORT b. ABSTRACT c

  15. Efficient dam break flood simulation methods for developing a preliminary evacuation plan after the Wenchuan Earthquake

    Directory of Open Access Journals (Sweden)

    Y. Li

    2012-01-01

    Full Text Available The Xiaojiaqiao barrier lake, which was the second largest barrier lake formed by the Wenchuan Earthquake had seriously threatened the lives and property of the population downstream. The lake was finally dredged successfully on 7 June 2008. Because of the limited time available to conduct an inundation potential analysis and make an evacuation plan, barrier lake information extraction and real-time dam break flood simulation should be carried out quickly, integrating remote sensing and geographic information system (GIS techniques with hydrologic/hydraulic analysis. In this paper, a technical framework and several key techniques for this real-time preliminary evacuation planning are introduced. An object-oriented method was used to extract hydrological information on the barrier lake from unmanned aerial vehicle (UAV remote sensing images. The real-time flood routine was calculated by using shallow-water equations, which were solved by means of a finite volume scheme on multiblock structured grids. The results of the hydraulic computations are visualized and analyzed in a 3-D geographic information system for inundation potential analysis, and an emergency response plan is made. The results show that if either a full-break or a half-break situation had occurred for the Chapinghe barrier lake on 19 May 2008, then the Xiaoba Town region and the Sangzao Town region would have been affected, but the downstream towns would have been less influenced. Preliminary evacuation plans under different dam break situations can be effectively made using these methods.

  16. Efficient dam break flood simulation methods for developing a preliminary evacuation plan after the Wenchuan Earthquake

    Science.gov (United States)

    Li, Y.; Gong, J. H.; Zhu, J.; Ye, L.; Song, Y. Q.; Yue, Y. J.

    2012-01-01

    The Xiaojiaqiao barrier lake, which was the second largest barrier lake formed by the Wenchuan Earthquake had seriously threatened the lives and property of the population downstream. The lake was finally dredged successfully on 7 June 2008. Because of the limited time available to conduct an inundation potential analysis and make an evacuation plan, barrier lake information extraction and real-time dam break flood simulation should be carried out quickly, integrating remote sensing and geographic information system (GIS) techniques with hydrologic/hydraulic analysis. In this paper, a technical framework and several key techniques for this real-time preliminary evacuation planning are introduced. An object-oriented method was used to extract hydrological information on the barrier lake from unmanned aerial vehicle (UAV) remote sensing images. The real-time flood routine was calculated by using shallow-water equations, which were solved by means of a finite volume scheme on multiblock structured grids. The results of the hydraulic computations are visualized and analyzed in a 3-D geographic information system for inundation potential analysis, and an emergency response plan is made. The results show that if either a full-break or a half-break situation had occurred for the Chapinghe barrier lake on 19 May 2008, then the Xiaoba Town region and the Sangzao Town region would have been affected, but the downstream towns would have been less influenced. Preliminary evacuation plans under different dam break situations can be effectively made using these methods.

  17. The effects of workload on respiratory variables in simulated flight: a preliminary study.

    Science.gov (United States)

    Karavidas, Maria Katsamanis; Lehrer, Paul M; Lu, Shou-En; Vaschillo, Evgeny; Vaschillo, Bronya; Cheng, Andrew

    2010-04-01

    In this pilot study, we investigated respiratory activity and end-tidal carbon dioxide (P(et)CO(2)) during exposure to varying levels of work load in a simulated flight environment. Seven pilots (age: 34-60) participated in a one-session test on the Boeing 737-800 simulator. Physiological data were collected while pilots wore an ambulatory multi-channel recording device. Respiratory variables, including inductance plethysmography (respiratory pattern) and pressure of end-tidal carbon dioxide (P(et)CO(2)), were collected demonstrating change in CO(2) levels proportional to changes in flight task workload. Pilots performed a set of simulation flight tasks. Pilot performance was rated for each task by a test pilot; and self-report of workload was taken using the NASA-TLX scale. Mixed model analysis revealed that respiration rate and minute ventilation are significantly associated with workload levels and evaluator scores controlling for "vanilla baseline" condition. Hypocapnia exclusively occurred in tasks where pilots performed more poorly. This study was designed as a preliminary investigation in order to develop a psychophysiological assessment methodology, rather than to offer conclusive findings. The results show that the respiratory system is very reactive to high workload conditions in aviation and suggest that hypocapnia may pose a flight safety risk under some circumstances. Copyright © 2010 Elsevier B.V. All rights reserved.

  18. Preliminary Simulations of CO2 Transport in the Dolostone Formations in the Ordos Basin, China

    Energy Technology Data Exchange (ETDEWEB)

    Hao, Y; Wolery, T; Carroll, S

    2009-04-30

    This report summarizes preliminary 2-D reactive-transport simulations on the injection, storage and transport of supercritical CO{sub 2} in dolostone formations in the Ordos Basin in China. The purpose of the simulations was to evaluate the role that basin heterogeneity, permeability, CO{sub 2} flux, and geochemical reactions between the carbonate geology and the CO{sub 2} equilibrated brines have on the evolution of porosity and permeability in the storage reservoir. The 2-D simulation of CO{sub 2} injection at 10{sup 3} ton/year corresponds to CO{sub 2} injection at a rate of 3 x 10{sup 5} ton/year in a 3-D, low permeable rock. An average permeability of 10 md was used in the simulation and reflects the upper range of permeability reported for the Ordos Basin Majiagou Group. Transport and distribution of CO{sub 2} between in the gas, aqueous, and solid phases were followed during a 10-year injection phase and a 10-year post injection phase. Our results show that CO{sub 2} flux and the spatial distribution of reservoir permeability will dictate the transport of CO{sub 2} in the injection and post injection phases. The injection rate of supercritical CO{sub 2} into low permeable reservoirs may need to be adjusted to avoid over pressure and mechanical damage to the reservoir. Although it should be noted that 3-D simulations are needed to more accurately model pressure build-up in the injection phase. There is negligible change in porosity and permeability due to carbonate mineral dissolution or anhydrite precipitation because a very small amount of carbonate dissolution is required to reach equilibrium with respect these phases. Injected CO{sub 2} is stored largely in supercritical and dissolved phases. During the injection phase, CO{sub 2} is transport driven by pressure build up and CO{sub 2} buoyancy.

  19. Alcohol elimination and simulator performance of male and female aviators: a preliminary report.

    Science.gov (United States)

    Taylor, J L; Dolhert, N; Friedman, L; Mumenthaler, M; Yesavage, J A

    1996-05-01

    In this preliminary study of alcohol effects on aviators' flight simulator performance, we addressed some methodological issues regarding possible gender-related differences in response to alcohol. Subjects were 11 male and 12 female general aviation pilots, ages 21-40. Subjects received 8 h of training before they were tested with alcohol. On the alcohol test day they were tested before drinking, while intoxicated (target BAC of 0.08%), and 8 h after drinking. The average, observed peak BAC readings for men and women were within 0.003% of each other. We observed faster disappearance rates for women such that women reached the FAA cutoff of 0.04% approximately 1 h before men, on average. Compared to predrink performance, there was a significant decrement in simulator performance during acute intoxication, but not 8 h after drinking. There were no significant gender differences in performance before or after drinking alcohol. Slower rates of alcohol elimination were associated with larger performance changes 8 h after drinking. This is the first report to our knowledge suggesting a possible relation between alcohol elimination rate and change in performance after drinking alcohol. A 12.5% dose reduction for women appears to be adequate for achieving comparable peak BAC's for male and female groups. Future studies using measures of circadian rhythmicity in conjunction with pharmacokinetic and performance measures could potentially shed light on differences in subjects' acute and delayed responses to alcohol.

  20. The Geoengineering Model Intercomparison Project Phase 6 (GeoMIP6: simulation design and preliminary results

    Directory of Open Access Journals (Sweden)

    B. Kravitz

    2015-10-01

    Full Text Available We present a suite of new climate model experiment designs for the Geoengineering Model Intercomparison Project (GeoMIP. This set of experiments, named GeoMIP6 (to be consistent with the Coupled Model Intercomparison Project Phase 6, builds on the previous GeoMIP project simulations, and has been expanded to address several further important topics, including key uncertainties in extreme events, the use of geoengineering as part of a portfolio of responses to climate change, and the relatively new idea of cirrus cloud thinning to allow more longwave radiation to escape to space. We discuss experiment designs, as well as the rationale for those designs, showing preliminary results from individual models when available. We also introduce a new feature, called the GeoMIP Testbed, which provides a platform for simulations that will be performed with a few models and subsequently assessed to determine whether the proposed experiment designs will be adopted as core (Tier 1 GeoMIP experiments. This is meant to encourage various stakeholders to propose new targeted experiments that address their key open science questions, with the goal of making GeoMIP more relevant to a broader set of communities.

  1. The Geoengineering Model Intercomparison Project Phase 6 (GeoMIP6): simulation design and preliminary results

    Science.gov (United States)

    Kravitz, B.; Robock, A.; Tilmes, S.; Boucher, O.; English, J. M.; Irvine, P. J.; Jones, A.; Lawrence, M. G.; MacCracken, M.; Muri, H.; Moore, J. C.; Niemeier, U.; Phipps, S. J.; Sillmann, J.; Storelvmo, T.; Wang, H.; Watanabe, S.

    2015-10-01

    We present a suite of new climate model experiment designs for the Geoengineering Model Intercomparison Project (GeoMIP). This set of experiments, named GeoMIP6 (to be consistent with the Coupled Model Intercomparison Project Phase 6), builds on the previous GeoMIP project simulations, and has been expanded to address several further important topics, including key uncertainties in extreme events, the use of geoengineering as part of a portfolio of responses to climate change, and the relatively new idea of cirrus cloud thinning to allow more longwave radiation to escape to space. We discuss experiment designs, as well as the rationale for those designs, showing preliminary results from individual models when available. We also introduce a new feature, called the GeoMIP Testbed, which provides a platform for simulations that will be performed with a few models and subsequently assessed to determine whether the proposed experiment designs will be adopted as core (Tier 1) GeoMIP experiments. This is meant to encourage various stakeholders to propose new targeted experiments that address their key open science questions, with the goal of making GeoMIP more relevant to a broader set of communities.

  2. Two-dimensional computer simulation of hypervelocity impact cratering: some preliminary results for Meteor Crater, Arizona

    Energy Technology Data Exchange (ETDEWEB)

    Bryan, J.B.; Burton, D.E.; Cunningham, M.E.; Lettis, L.A. Jr.

    1978-06-01

    A computational approach used for subsurface explosion cratering was extended to hypervelocity impact cratering. Meteor (Barringer) Crater, Arizona, was selected for the first computer simulation because it is one of the most thoroughly studied craters. It is also an excellent example of a simple, bowl-shaped crater and is one of the youngest terrestrial impact craters. Initial conditions for this calculation included a meteorite impact velocity of 15 km/s, meteorite mass of 1.67 x 10/sup 8/ kg, with a corresponding kinetic energy of 1.88 x 10/sup 16/ J (4.5 megatons). A two-dimensional Eulerian finite difference code called SOIL was used for this simulation of a cylindrical iron projectile impacting at normal incidence into a limestone target. For this initial calculation, a Tillotson equation-of-state description for iron and limestone was used with no shear strength. Results obtained for this preliminary calculation of the formation of Meteor Crater are in good agreement with field measurements. A color movie based on this calculation was produced using computer-generated graphics. 19 figures, 5 tables, 63 references.

  3. Interpretation and preliminary simulation of the 40 ka periodicity of the Quaternary glaciation

    Institute of Scientific and Technical Information of China (English)

    LI Nan; CHEN Xing

    2007-01-01

    More and more proxy records approved that the periodicity of the glacial cycles is about 40 ka before MPT (middle Pleistocene transition) as early as late Tertiary from 3.0 Ma to 0.9 Ma, whereas it changes to about 100 ka after MPT.Summer insolation at high latitude in Northern Hemisphere, usually considered as the main external force for the ice age, is dominated by the 23 ka precession period, which does not match the period of the glacial cycles.In this paper, we define an energy index C and its threshold Ct that indicate the net energy supply and the overall response of the climate system.The difference between these two parameters determines whether the ice sheet melts or not, and accordingly the start and termination of the interglacial stages, as well as the periodicity of glacial oscillations.Based on the energy threshold hypothesis, the preliminary simulation experiments are made to test the period of the glacial cycles and driven factors from a conceptual model.The results indicate that energy index C and threshold Ct can interpret not only the 40 ka periodicity before MPT, but also the quasi-100 ka periodicity after MPT to some extent, and the 40 ka is the basic period of the glacial cycles, which discloses the inherent continuity of climatic change before and after MPT.

  4. Modeling and Simulation of Ceramic Arrays to Improve Ballistic Performance

    Science.gov (United States)

    2014-04-30

    distribution is Unlimited. 13. SUPPLEMENTARY NOTES 14. ABSTRACT -Develop Modeling and Simulation tools, use Depth of Penetration ( DOP ) as metric...7.62 APM2 -Evaluate SiC tile on Aluminum with material properties from literature -Develop seam designs to improve performance, demonstrate with DOP ...5083, SiC, DoP Expeminets, AutoDyn Sin 16. SECURITY CLASSIFICATION OF: UU a. REPORT b. ABSTRACT c. THIS PAGE 17. LIMITATION OF ABSTRACT UU 18

  5. A two-parameter preliminary optimization study for a fluidized-bed boiler through a comprehensive mathematical simulator

    Energy Technology Data Exchange (ETDEWEB)

    Rabi, Jose A.; Souza-Santos, Marcio L. de [Universidade Estadual de Campinas, SP (Brazil). Faculdade de Engenharia Mecanica. Dept. de Energia]. E-mails: jrabi@fem.unicamp.br; dss@fem.unicamp.br

    2000-07-01

    Modeling and simulation of fluidized-bed equipment have demonstrated their importance as a tool for design and optimization of industrial equipment. Accordingly, this work carries on an optimization study of a fluidized-bed boiler with the aid of a comprehensive mathematical simulator. The configuration data of the boiler are based on a particular Babcock and Wilcox Co. (USA) test unit. Due to their importance, the number of tubes in the bed section and the air excess are chosen as the parameters upon which the optimization study is based. On their turn, the fixed-carbon conversion factor and the boiler efficiency are chosen as two distinct optimization objectives. The results from both preliminary searches are compared. The present work is intended to be just a study on possible routes for future optimization of larger boilers. Nonetheless, the present discussion might give some insight on the equipment behavior. (author)

  6. Preliminary investigations of Monte Carlo Simulations of neutron energy and LET spectra for fast neutron therapy facilities

    CERN Document Server

    Kroc, T K

    2012-01-01

    No fast neutron therapy facility has been built with optimized beam quality based on a thorough understanding of the neutron spectrum and its resulting biological effectiveness. A study has been initiated to provide the information necessary for such an optimization. Monte Carlo studies will be used to simulate neutron energy spectra and LET spectra. These studies will be bench-marked with data taken at existing fast neutron therapy facilities. Results will also be compared with radiobiological studies to further support beam quality optimization. These simulations, anchored by this data, will then be used to determine what parameters might be optimized to take full advantage of the unique LET properties of fast neutron beams. This paper will present preliminary work in generating energy and LET spectra for the Fermilab fast neutron therapy facility.

  7. Preliminary Results on Simulations of Ground Level Enhancements (GLEs) detected by The High Altitude Water Cherenkov Observatory (HAWC)

    Science.gov (United States)

    Enriquez Rivera, O.; Lara, A.

    2014-12-01

    The High Altitude Water Cherenkov Observatory (HAWC) is currently under construction at the Sierra Negra Volcano, Puebla in Mexico. Located 4100 m above sea level, this large array is mainly designed to observe high energy gamma rays (TeV). However, by recording scaler data that correspond to the rates of individual photomultiplier tubes, the detection and study of solar energetic particles (known as Ground Level Enhancements) as well as the decrease of the cosmic ray flux due to solar transients (known as Forbush decreases) will also be possible. In order to determine the response of the array to solar transients, we have performed simulations of the scaler output using different sub-array configurations. We present here our preliminary results of such simulations and their comparison with observed Forbush decreases.

  8. The shock compression of microorganism-loaded broths and emulsions: Experiments and simulations

    OpenAIRE

    Hazell, P. J.; Beveridge, C.; Groves, K.; Appleby-Thomas, G.

    2010-01-01

    Abstract By carefully selecting flyer plate thickness and the geometry of a target capsule for bacterial broths and emulsions, we have successfully subjected the contents of the capsule to simultaneous shock and dynamic compression when subjected to a flyer-plate impact experiment. The capsules were designed to be recovered intact so that post experimental analysis could be done on the contents. ANSYS? AUTODYN hydrocode simulations were carried out to interrogate the deformation of...

  9. Mini-DIAL system measurements coupled with multivariate data analysis to identify TIC and TIM simulants: preliminary absorption database analysis.

    Science.gov (United States)

    Gaudio, P.; Malizia, A.; Gelfusa, M.; Martinelli, E.; Di Natale, C.; Poggi, L. A.; Bellecci, C.

    2017-01-01

    Nowadays Toxic Industrial Components (TICs) and Toxic Industrial Materials (TIMs) are one of the most dangerous and diffuse vehicle of contamination in urban and industrial areas. The academic world together with the industrial and military one are working on innovative solutions to monitor the diffusion in atmosphere of such pollutants. In this phase the most common commercial sensors are based on “point detection” technology but it is clear that such instruments cannot satisfy the needs of the smart cities. The new challenge is developing stand-off systems to continuously monitor the atmosphere. Quantum Electronics and Plasma Physics (QEP) research group has a long experience in laser system development and has built two demonstrators based on DIAL (Differential Absorption of Light) technology could be able to identify chemical agents in atmosphere. In this work the authors will present one of those DIAL system, the miniaturized one, together with the preliminary results of an experimental campaign conducted on TICs and TIMs simulants in cell with aim of use the absorption database for the further atmospheric an analysis using the same DIAL system. The experimental results are analysed with standard multivariate data analysis technique as Principal Component Analysis (PCA) to develop a classification model aimed at identifying organic chemical compound in atmosphere. The preliminary results of absorption coefficients of some chemical compound are shown together pre PCA analysis.

  10. Preliminary simulation of a M6.5 earthquake on the Seattle Fault using 3D finite-difference modeling

    Science.gov (United States)

    Stephenson, William J.; Frankel, Arthur D.

    2000-01-01

    A three-dimensional finite-difference simulation of a moderate-sized (M 6.5) thrust-faulting earthquake on the Seattle fault demonstrates the effects of the Seattle Basin on strong ground motion in the Puget lowland. The model area includes the cities of Seattle, Bremerton and Bellevue. We use a recently developed detailed 3D-velocity model of the Seattle Basin in these simulations. The model extended to 20-km depth and assumed rupture on a finite fault with random slip distribution. Preliminary results from simulations of frequencies 0.5 Hz and lower suggest amplification can occur at the surface of the Seattle Basin by the trapping of energy in the Quaternary sediments. Surface waves generated within the basin appear to contribute to amplification throughout the modeled region. Several factors apparently contribute to large ground motions in downtown Seattle: (1) radiation pattern and directivity from the rupture; (2) amplification and energy trapping within the Quaternary sediments; and (3) basin geometry and variation in depth of both Quaternary and Tertiary sediments

  11. Microarray analysis of genes differentially expressed in HepG2 cells cultured in simulated microgravity: preliminary report

    Science.gov (United States)

    Khaoustov, V. I.; Risin, D.; Pellis, N. R.; Yoffe, B.; McIntire, L. V. (Principal Investigator)

    2001-01-01

    Developed at NASA, the rotary cell culture system (RCCS) allows the creation of unique microgravity environment of low shear force, high-mass transfer, and enables three-dimensional (3D) cell culture of dissimilar cell types. Recently we demonstrated that a simulated microgravity is conducive for maintaining long-term cultures of functional hepatocytes and promote 3D cell assembly. Using deoxyribonucleic acid (DNA) microarray technology, it is now possible to measure the levels of thousands of different messenger ribonucleic acids (mRNAs) in a single hybridization step. This technique is particularly powerful for comparing gene expression in the same tissue under different environmental conditions. The aim of this research was to analyze gene expression of hepatoblastoma cell line (HepG2) during early stage of 3D-cell assembly in simulated microgravity. For this, mRNA from HepG2 cultured in the RCCS was analyzed by deoxyribonucleic acid microarray. Analyses of HepG2 mRNA by using 6K glass DNA microarray revealed changes in expression of 95 genes (overexpression of 85 genes and downregulation of 10 genes). Our preliminary results indicated that simulated microgravity modifies the expression of several genes and that microarray technology may provide new understanding of the fundamental biological questions of how gravity affects the development and function of individual cells.

  12. Preliminary Results from Simulations of Temperature Oscillations in Stirling Engine Regenerator Matrices

    DEFF Research Database (Denmark)

    Andersen, Stig Kildegård; Carlsen, Henrik; Thomsen, Per Grove

    2006-01-01

    The objective of this study has been to create a Stirling engine model for studying the effects of regenerator matrix temperature oscillations on Stirling engine performance. A one-dimensional model with axial discretisation of engine components has been formulated using the control volume method....... The model contains a system of ordinary differential equations (ODEs) derived from mass and energy balances for gas filled control volumes and energy balances for regenerator matrix control masses. Interpolation methods with filtering properties are used for state variables at control volume interfaces...... shooting method. It has been found possible to accurately solve the stiff ODE system that describes the coupled thermodynamics of the gas and the regenerator matrix and to reliably find periodic steady state solutions to the model. Preliminary results indicate that the regenerator matrix temperature...

  13. Regional hydrogeological simulations using CONECTFLOW. Preliminary site description. Laxemar sub area - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Hartley, Lee; Hunter, Fiona; Jackson, Peter; McCarthy, Rachel [Serco Assurance, Risley (United Kingdom); Gylling, Bjoern; Marsic, Niko [Kemakta Konsult AB, Stockholm (Sweden)

    2006-04-15

    The main objective of this study is to support the development of a preliminary Site Description of the Laxemar subarea on a regional-scale based on the available data of November 2004 (Data Freeze L1.2). A more specific objective of this study is to assess the role of both known and less quantified hydrogeological conditions in determining the present-day distribution of saline groundwater in the Laxemar subarea on a regional-scale. An improved understanding of the palaeo-hydrogeology is necessary in order to gain credibility for the Site Description in general and the hydrogeological description in particular. This is to serve as a basis for describing the present hydrogeological conditions on a local-scale, as well as predictions of future hydrogeological conditions. Another objective is to assess the flow-paths from the local-scale model domain, based on the present-day flow conditions, to assess the distribution of discharge and recharge areas connected to the flow at the approximate repository depth to inform the Preliminary Safety Evaluation. Significant new features incorporated in the modelling include: a depth variation in hydraulic properties within the deformation zones; a dependence on rock domain and depth in the rock mass properties in regional-scale models; a more detailed model of the overburden in terms of a layered system of spatially variable thickness made up of several different types of Quaternary deposits has been implemented; and several variants on the position of the watertable have been tried. The motivation for introducing a dependence on rock domain was guided by the hydrogeological interpretation with the aim of honouring the observed differences in hydraulic properties measured at the boreholes.

  14. Preliminary evaluation of a virtual reality-based simulator for learning spinal anesthesia.

    LENUS (Irish Health Repository)

    2012-12-27

    STUDY OBJECTIVE: To evaluate the influence of a simulation-based program on the initial performance of dural puncture by medical interns, and to refine the design of simulator-based teaching and competence assessment. DESIGN: Prospective interventional study. SETTING: Academic medical center. SUBJECTS: 27 medical interns inexperienced in the technique of spinal anesthesia or dural puncture and within 12 months of graduating from medical school, were randomly assigned to a conventional or a simulator-based teaching course of spinal anesthesia: 13 were recruited to the Conventional Group (CG) and 14 to the Simulator Group (SG). MEASUREMENTS: A SenseGraphic Immersive workbench and a modified Phantom desktop with shutter glasses were used to create a teaching environment. Outcomes of teaching were assessed in two phases within three weeks of the teaching course: Phase I consisted of a written examination followed by assessment on the simulator. A global rating scale and a task-specific checklist were used. Phase II (for those participants for whom a suitable opportunity arose to perform spinal anesthesia under supervision within three wks of the teaching course) consisted of structured observation of clinical performance of the procedure in the operating room. Participants were assessed by independent, study-blinded experts. Student\\'s two-tailed impaired t-tests were used to compare the parametric outcomes (P < 0.05 was considered significant). MAIN RESULTS: All participants completed the written test successfully with no difference between groups. Ten participants from CG and 13 from SG completed the simulator-based testing performing similarly in terms of the global rating scale. Five participants in CG and 6 in SG proceeded to clinical testing. On the global rating scale, interns in SG scored higher than those in CG. They performed similarly according to the task-specific checklist. CONCLUSIONS: Overall, no difference was measured between those taught with

  15. Preliminary Assessment of the Mars Science Laboratory Entry, Descent, and Landing Simulation

    Science.gov (United States)

    Way, David W.

    2013-01-01

    On August 5, 2012, the Mars Science Laboratory rover, Curiosity, successfully landed inside Gale Crater. This landing was only the seventh successful landing and fourth rover to be delivered to Mars. Weighing nearly one metric ton, Curiosity is the largest and most complex rover ever sent to investigate another planet. Safely landing such a large payload required an innovative Entry, Descent, and Landing system, which included the first guided entry at Mars, the largest supersonic parachute ever flown at Mars, and a novel and untested Sky Crane landing system. A complete, end-to-end, six degree-of-freedom, multibody computer simulation of the Mars Science Laboratory Entry, Descent, and Landing sequence was developed at the NASA Langley Research Center. In-flight data gathered during the successful landing is compared to pre-flight statistical distributions, predicted by the simulation. These comparisons provide insight into both the accuracy of the simulation and the overall performance of the vehicle.

  16. A Preliminary Study on Soft Tissue Cutting in Virtual Surgery Simulation

    Institute of Scientific and Technical Information of China (English)

    JIA Shi-yu; PAN Zhen-kuan

    2004-01-01

    A method for simulation of cutting virtual soft tissue objects made of tetrahedron elements is developed. A linear isotropic elastic model is used for the soft tissue material properties and a tensor-mass model chosen for the physical deformation. The Verlet leapfrog method is used to perform time integration in solving the dynamic equations. Cutting is simulated by simply removing the tetrahedron elements that are intersected with the virtual scalpel. By making use of the spatial coherence, collision detection between soft tissue objects and the virtual scalpel is sped up. To facilitate the simulation, the soft tissue object is represented by linked lists of vertices, edges and tetra elements with pointers to the related neighboring features. The established software framework can serve as a base for the future development. Results of virtual experiments are shown and discussed. Possible future directions are also given.

  17. Hydrograph simulation models of the Hillsborough and Alafia Rivers, Florida: a preliminary report

    Science.gov (United States)

    Turner, James F.

    1972-01-01

    Mathematical (digital) models that simulate flood hydrographs from rainfall records have been developed for the following gaging stations in the Hillsborough and Alafia River basins of west-central Florida: Hillsborough River near Tampa, Alafia River at Lithia, and north Prong Alafia River near Keysville. These models, which were developed from historical streamflow and and rainfall records, are based on rainfall-runoff and unit-hydrograph procedures involving an arbitrary separation of the flood hydrograph. These models assume the flood hydrograph to be composed of only two flow components, direct (storm) runoff, and base flow. Expressions describing these two flow components are derived from streamflow and rainfall records and are combined analytically to form algorithms (models), which are programmed for processing on a digital computing system. Most Hillsborough and Alafia River flood discharges can be simulated with expected relative errors less than or equal to 30 percent and flood peaks can be simulated with average relative errors less than 15 percent. Because of the inadequate rainfall network that is used in obtaining input data for the North Prong Alafia River model, simulated peaks are frequently in error by more than 40 percent, particularly for storms having highly variable areal rainfall distribution. Simulation errors are the result of rainfall sample errors and, to a lesser extent, model inadequacy. Data errors associated with the determination of mean basin precipitation are the result of the small number and poor areal distribution of rainfall stations available for use in the study. Model inadequacy, however, is attributed to the basic underlying theory, particularly the rainfall-runoff relation. These models broaden and enhance existing water-management capabilities within these basins by allowing the establishment and implementation of programs providing for continued development in these areas. Specifically, the models serve not only as a

  18. Preliminary study on LGM climate simulation and the diagnosis for East Asia

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    LGM climate study is a hot topic in international fields on global changes. Climate simulation in this study applies both common designs of 21 kaBP boundary conditions from the Paleoclimate Modeling Intercomparison Project (PMIP), including insolation, glaciation, sea surface temperature and atmospheric CO2 concentration, and land surface conditions from Eurasia continent by compilation of geological evidence. The simulation outputs are in agreement with climate spatial patterns reconstructed by observation records. Sensitive experiment on land surface conditions shows that changes in vegetation would make significant impacts on temperature and precipitation. Particularly in the Tibetan Plateau, this change would increase in differences of winter and summer temperature, precipitation and P-E.

  19. Preliminary Design and Simulation of a Turbo Expander for Small Rated Power Organic Rankine Cycle (ORC

    Directory of Open Access Journals (Sweden)

    Roberto Capata

    2014-11-01

    Full Text Available Nowadays, the Organic Rankine Cycle (ORC system, which operates with organic fluids, is one of the leading technologies for “waste energy recovery”. It works as a conventional Rankine Cycle but, as mentioned, instead of steam/water, an organic fluid is used. This change allows it to convert low temperature heat into electric energy where required. Large numbers of studies have been carried out to identify the most suitable fluids, system parameters and the various configurations. In the present market, most ORC systems are designed and manufactured for the recovery of thermal energy from various sources operating at “large power rating” (exhaust gas turbines, internal combustion engines, geothermal sources, large melting furnaces, biomass, solar, etc.; from which it is possible to produce a large amount of electric energy (30 kW ÷ 300 kW. Such applications for small nominal power sources, as well as the exhaust gases of internal combustion engines (car sedan or town, ships, etc. or small heat exchangers, are very limited. The few systems that have been designed and built for small scale applications, have, on the other hand, different types of expander (screw, scroll, etc.. These devices are not adapted for placement in small and restricted places like the interior of a conventional car. The aim of this work is to perform the preliminary design of a turbo-expander that meets diverse system requirements such as low pressure, small size and low mass flow rates. The expander must be adaptable to a small ORC system utilizing gas of a diesel engine or small gas turbine as thermal source to produce 2–10 kW of electricity. The temperature and pressure of the exhaust gases, in this case study (400–600 °C and a pressure of 2 bar, imposes a limit on the use of an organic fluid and on the net power that can be produced. In addition to water, fluids such as CO2, R134a and R245fa have been considered. Once the operating fluids has been chosen

  20. Design and preliminary validation of a tool for the simulation of train braking performance

    Institute of Scientific and Technical Information of China (English)

    Luca Pugi; Monica Malvezzi; Susanna Papini; Gregorio Vettori

    2013-01-01

    Train braking performance is important for the safety and reliability of railway systems. The availability of a tool that allows evaluating such performance on the basis of the main train features can be useful for train system designers to choose proper dimensions for and optimize train’s subsystems. This paper presents a modular tool for the prediction of train braking performance, with a par-ticular attention to the accurate prediction of stopping distances. The tool takes into account different loading and operating conditions, in order to verify the safety require-ments prescribed by European technical specifications for interoperability of high-speed trains and the corresponding EN regulations. The numerical results given by the tool were verified and validated by comparison with experi-mental data, considering as benchmark case an Ansaldo EMU V250 train-a European high-speed train-currently developed for Belgium and Netherlands high-speed lines, on which technical information and experimental data directly recorded during the preliminary tests were avail-able. An accurate identification of the influence of the braking pad friction factor on braking performances allowed obtaining reliable results.

  1. Preliminary results from simulations of temperature oscillations in Stirling engine regenerator matrices

    Energy Technology Data Exchange (ETDEWEB)

    Andersen, Stig Kildegaard [Department of Mechanical Engineering, Technical University of Denmark, DK-2800 Lyngby (Denmark)]. E-mail: ska@mek.dtu.dk; Carlsen, Henrik [Department of Mechanical Engineering, Technical University of Denmark, DK-2800 Lyngby (Denmark); Thomsen, Per Grove [Informatics and Mathematical Modelling, Technical University of Denmark, DK-2800 Lyngby (Denmark)

    2006-08-15

    The objective of this study has been to create a Stirling engine model for studying the effects of regenerator matrix temperature oscillations on Stirling engine performance. A one-dimensional model with axial discretisation of engine components has been formulated using the control volume method. The model contains a system of ordinary differential equations (ODEs) derived from mass and energy balances for gas filled control volumes and energy balances for regenerator matrix control masses. Interpolation methods with filtering properties are used for state variables at control volume interfaces to reduce numerical diffusion and/or non-physical oscillations. Loss mechanisms are included directly in the governing equations as terms in the mass and energy balances. Steady state periodic solutions that satisfy cyclic boundary conditions and integral conditions are calculated using a custom built shooting method. It has been found possible to accurately solve the stiff ODE system that describes the coupled thermodynamics of the gas and the regenerator matrix and to reliably find periodic steady state solutions to the model. Preliminary results indicate that the regenerator matrix temperature oscillations do have significant impact on the regenerator loss, the cycle power output, and the cycle efficiency and thus deserve further study.

  2. Post-impact climate conditions on early Mars: preliminary results from GCM simulations

    Science.gov (United States)

    Steakley, Kathryn; Murphy, Jim; Kahre, Melinda A.; Haberle, Robert

    2016-10-01

    Observations imply that liquid water was stable on Mars' surface during the late Noachian/early Hesperian era, with valley networks forming roughly 3.5-3.75 billion years ago, possibly from precipitation and runoff (Fassett & Head 2008, Icarus 195, 61; Hynek et al., 2010, JGR Planets, 115, E09008). Climate models, however, struggle to reproduce such warm conditions (Forget et al., 2013, Icarus 21, 81). Volcanism and impacts have been suggested as mechanisms of either inducing a warm and wet environment or causing local melting in a cold and wet environment. Comets and asteroids are capable of injecting into the atmosphere both kinetic energy from the impact and water from the object itself and from vaporized surface and subsurface ice. Segura et al. (2008, JGR Planets 113, E11007) find using a 1-D atmospheric model that significant rainfall and periods of above-freezing temperatures lasting months to years can follow impacts of objects between 30 and 100 km in diameter. We revisit this work utilizing a 3-D global climate model (GCM) to consider the effects of dynamics, topography, global surface ice variations, etc. We present preliminary results from the NASA ARC Mars GCM investigating global temperature and precipitation behavior in a post-impact, early Mars environment.

  3. Preliminary reactive geochemical transport simulation study on CO2 geological sequestration at the Changhua Coastal Industrial Park Site, Taiwan

    Science.gov (United States)

    Sung, R.; Li, M.

    2013-12-01

    Mineral trapping by precipitated carbonate minerals is one of critical mechanisms for successful long-term geological sequestration (CGS) in deep saline aquifer. Aquifer acidification induced by the increase of carbonic acid (H2CO3) and bicarbonate ions (HCO3-) as the dissolution of injected CO2 may induce the dissolution of minerals and hinder the effectiveness of cap rock causing potential risk of CO2 leakage. Numerical assessments require capabilities to simulate complicated interactions of thermal, hydrological, geochemical multiphase processes. In this study, we utilized TOUGHREACT model to demonstrate a series of CGS simulations and assessments of (1) time evolution of aquifer responses, (2) migration distance and spatial distribution of CO2 plume, (3) effects of CO2-saline-mineral interactions, and (4) CO2 trapping components at the Changhua Costal Industrial Park (CCIP) Site, Taiwan. The CCIP Site is located at the Southern Taishi Basin with sloping and layered heterogeneous formations. At this preliminary phase, detailed information of mineralogical composition of reservoir formation and chemical composition of formation water are difficult to obtain. Mineralogical composition of sedimentary rocks and chemical compositions of formation water for CGS in deep saline aquifer from literatures (e.g. Xu et al., 2004; Marini, 2006) were adopted. CGS simulations were assumed with a constant CO2 injection rate of 1 Mt/yr at the first 50 years. Hydrogeological settings included porosities of 0.103 for shale, 0.141 for interbedding sandstone and shale, and 0.179 for sandstone; initial pore pressure distributions of 24.5 MPa to 28.7 MPa, an ambient temperature of 70°C, and 0.5 M of NaCl in aqueous solution. Mineral compositions were modified from Xu et al. (2006) to include calcite (1.9 vol. % of solid), quartz (57.9 %), kaolinite (2.0 %), illite (1.0 %), oligoclase (19.8 %), Na-smectite (3.9 %), K-feldspar (8.2 %), chlorite (4.6 %), and hematite (0.5 %) and were

  4. Simulated tsunami run-up amplification factors around Penang Island for preliminary risk assessment

    Science.gov (United States)

    Lim, Yong Hui; Kh'ng, Xin Yi; Teh, Su Yean; Koh, Hock Lye; Tan, Wai Kiat

    2017-08-01

    The mega-tsunami Andaman that struck Malaysia on 26 December 2004 affected 200 kilometers of northwest Peninsular Malaysia coastline from Perlis to Selangor. It is anticipated by the tsunami scientific community that the next mega-tsunami is due to occur any time soon. This rare catastrophic event has awakened the attention of Malaysian government to take appropriate risk reduction measures, including timely and orderly evacuation. To effectively evacuate ordinary citizens to a safe ground or a nearest designated emergency shelter, a well prepared evacuation route is essential with the estimated tsunami run-up heights and inundation distances on land clearly indicated on the evacuation map. The run-up heights and inundation distances are simulated by an in-house model 2-D TUNA-RP based upon credible scientific tsunami source scenarios derived from tectonic activity around the region. To provide a useful tool for estimating the run-up heights along the entire coast of Penang Island, we computed tsunami amplification factors based upon 2-D TUNA-RP model simulations in this paper. The inundation map and run-up amplification factors in six domains along the entire coastline of Penang Island are provided. The comparison between measured tsunami wave heights for the 2004 Andaman tsunami and TUNA-RP model simulated values demonstrates good agreement.

  5. [Simulation-based intervention to improve anesthesiology residents communication with families of critically ill patients--preliminary prospective evaluation].

    Science.gov (United States)

    Berkenstadt, Haim; Perlson, Daria; Shalomson, Orit; Tuval, Atalia; Haviv-Yadid, Yael; Ziv, Amitai

    2013-08-01

    Although effective communication with families of critically ill patients is a vital component of quality care, training in this field is neglected. The article aims to validate communication skills training program for anesthesiology residents in the intensive care set up. Ten anesthesia residents, following 3 months of Intensive Care Unit (ICU) rotation, had 4 hours of lectures and one day simulation-based communication skills training with families of critically ill patients. Participants completed an attitude questionnaire over 3 time periods--before training [t1], immediately following training (t2) and three months following training (t3). The participants' communication skills were assessed by two blinded independent observers using the SEGUE framework while performing a simulation-based scenario at t1 and t3. Seven participants finished the study protocol. Participants ndicated communication importance as 3.68 +/- 0.58 (t1), 4.05 +/- 0.59 (t2), 4.13 +/- 0.64 (t3); their communication ability as 3.09 +/- 0.90 (t1), 3.70 +/- 0.80 (t2), 3.57 +/- 0.64 (t3); the contribution of lecture to communication 3.04 +/- 0.43 (t1), 3.83 +/- 0.39 (t2), 3.87 +/- 0.51 (t3), and contribution of simulation training to communication 3.00 +/- 0.71 (t1), 4.04 +/- 0.52 (t2), 3.84 +/- 0.31 (t3). The differences did not reach statistical significance. Objective assessment of the communication skills using the SEGUE framework indicated that 6/7 participants improved their communication skills, with communication ability before training at 2.66 +/- 0.83 and 1 month following training it was 3.38 +/- 0.78 (p = 0.09). This preliminary study demonstrates the value of communication skills training in the intensive care environment.

  6. Dynamic Stability of Passive Bipedal Walking on Rough Terrain:A Preliminary Simulation Study

    Institute of Scientific and Technical Information of China (English)

    Parsa Nassiri Afshar; Lei Ren

    2012-01-01

    A simplified 2D passive dynamic model was simulated to walk down on a rough slope surface defined by deterministic profiles to investigate how the walking stability changes with increasing surface roughness.Our results show that the passive walker can walk on rough surfaces subject to surface roughness up to approximately 0.1% of its leg length.This indicates that bipedal walkers based on passive dynamics may possess some intrinsic stability to adapt to rough terrains although the maximum roughness they can tolerate is small.Orbital stability method was used to quantify the walking stability before the walker started to fall over.It was found that the average maximum Floquet multiplier increases with surface roughness in a non-linear form.Although the passive walker remained orbitally stable for all the simulation cases,the results suggest that the possibility of the bipedal model moving away from its limit cycle increases with the surface roughness if subjected to additional perturbations.The number of consecutive steps before falling was used to measure the walking stability after the passive walker started to fall over.The results show that the number of steps before falling decreases exponentially with the increase in surface roughness.When the roughness magnitude approached to 0.73% of the walker's leg length,it fell down to the ground as soon as it entered into the uneven terrain.It was also found that shifting the phase angle of the surface profile has apparent affect on the system stability.This is probably because point contact was used to simulate the heel strikes and the resulted variations in system states at heel strikes may have pronounced impact on the passive gaits,which have narrow basins of attraction.These results would provide insight into how the dynamic stability of passive bipedal walkers evolves with increasing surface roughness.

  7. Preliminary Assessment of Tecplot Chorus for Analyzing Ensemble of CTH Simulations

    Energy Technology Data Exchange (ETDEWEB)

    Agelastos, Anthony Michael [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Stevenson, Joel O. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Attaway, Stephen W. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Peterson, David

    2015-04-01

    The exploration of large parameter spaces in search of problem solution and uncertainty quantifcation produces very large ensembles of data. Processing ensemble data will continue to require more resources as simulation complexity and HPC platform throughput increase. More tools are needed to help provide rapid insight into these data sets to decrease manual processing time by the analyst and to increase knowledge the data can provide. One such tool is Tecplot Chorus, whose strengths are visualizing ensemble metadata and linked images. This report contains the analysis and conclusions from evaluating Tecplot Chorus with an example problem that is relevant to Sandia National Laboratories.

  8. Preliminary investigations on 3D PIC simulation of DPHC structure using NEPTUNE3D code

    Science.gov (United States)

    Zhao, Hailong; Dong, Ye; Zhou, Haijing; Zou, Wenkang; Wang, Qiang

    2016-10-01

    Cubic region (34cm × 34cm × 18cm) including the double post-hole convolute (DPHC) structure was chosen to perform a series of fully 3D PIC simulations using NEPTUNE3D codes, massive data ( 200GB) could be acquired and solved in less than 5 hours. Cold-chamber tests were performed during which only cathode electron emission was considered without temperature rise or ion emission, current loss efficiency was estimated by comparisons between output magnetic field profiles with or without electron emission. PIC simulation results showed three stages of current transforming process with election emission in DPHC structure, the maximum ( 20%) current loss was 437kA at 15ns, while only 0.46% 0.48% was lost when driving current reached its peak. DPHC structure proved valuable functions during energy transform process in PTS facility, and NEPTUNE3D provided tools to explore this sophisticated physics. Project supported by the National Natural Science Foundation of China, Grant No. 11571293, 11505172.

  9. Preliminary Molecular Dynamic Simulations of the Estrogen Receptor Alpha Ligand Binding Domain from Antagonist to Apo

    Directory of Open Access Journals (Sweden)

    Adrian E. Roitberg

    2008-06-01

    Full Text Available Estrogen receptors (ER are known as nuclear receptors. They exist in the cytoplasm of human cells and serves as a DNA binding transcription factor that regulates gene expression. However the estrogen receptor also has additional functions independent of DNA binding. The human estrogen receptor comes in two forms, alpha and beta. This work focuses on the alpha form of the estrogen receptor. The ERα is found in breast cancer cells, ovarian stroma cells, endometrium, and the hypothalamus. It has been suggested that exposure to DDE, a metabolite of DDT, and other pesticides causes conformational changes in the estrogen receptor. Before examining these factors, this work examines the protein unfolding from the antagonist form found in the 3ERT PDB crystal structure. The 3ERT PDB crystal structure has the estrogen receptor bound to the cancer drug 4-hydroxytamoxifen. The 4-hydroxytamoxifen ligand was extracted before the simulation, resulting in new conformational freedom due to absence of van der Waals contacts between the ligand and the receptor. The conformational changes that result expose the binding clef of the co peptide beside Helix 12 of the receptor forming an apo conformation. Two key conformations in the loops at either end of the H12 are produced resulting in the antagonist to apo conformation transformation. The results were produced over a 42ns Molecular Dynamics simulation using the AMBER FF99SB force field.

  10. Preliminary evaluation of a virtual reality dental simulation system on drilling operation.

    Science.gov (United States)

    Wang, Dangxiao; Zhao, Siming; Li, Teng; Zhang, Yuru; Wang, Xiaoyan

    2015-01-01

    To evaluate the fidelity of the iDental system and investigate its utility and performance on simulated drilling operations, user studies consisting of objective and subjective evaluations were performed. A voxel-based drilling simulation sub-system in the iDental system was employed for evaluation. Twenty participants were enrolled to take part in the experiments and were divided into two groups: novice and resident. A combined evaluation method including objective and subjective methods was employed. The objective evaluation included two dental drilling tasks: caries removal operation and pulp chamber opening operation. In the subjective method, participants were required to complete a questionnaire to evaluate the fidelity of the system after the operation task. Based on the structured global assessment scales in the questionnaire, the average subjective evaluation scores of the proposed metrics were greater than 4.5, demonstrating that the system operated above medium fidelity. Dentists expressed great interest and positive attitudes toward the potential of the iDental system. The objective evaluation data including time spent and the volume of removed healthy and carious tissue were obtained. Although no significant differences could be found between the two groups, the volume of removed caries and the depth of pulp chamber insertion manifested small standard deviations. Evaluation results illustrated that dentists were willing to use the virtual reality training system. Several future research topics were identified, including increasing the task difficulty, improving the system fidelity and introducing appropriate finger rest points.

  11. Preliminary report on airline pilot scan patterns during simulated ILS approach

    Science.gov (United States)

    Spady, A. A., Jr.

    1976-01-01

    A series of ILS approaches using seven airline-rated Boeing 737 pilots in an FAA qualified simulator have been conducted. The test matrix included both manual and coupled approaches with and without atmospheric turbulence in Category II weather. A nonintrusive oculometer system was used to track the pilot's eye-point-of-regard throughout the approach. The results indicate that, in general, the pilots use a different scan technique for the manual and coupled conditions; however, the introduction of atmospheric turbulence does not greatly affect the scan behavior in either case. A comparison is made between the objective measures of the instrument scan (oculometer data) and the pilots' opinions of their instrument use. The data show a high degree of consistency among pilots for both the quantitative data and the qualitative data (pilots' opinions). However, there is a slightly lower agreement between the quantitative and qualitative measures.

  12. High Frame-Rate Blood Vector Velocity Imaging Using Plane Waves: Simulations and Preliminary Experiments

    DEFF Research Database (Denmark)

    Udesen, Jesper; Gran, Fredrik; Hansen, Kristoffer Lindskov;

    2008-01-01

    Conventional ultrasound methods for acquiring color images of blood velocity are limited by a relatively low frame-rate and are restricted to give velocity estimates along the ultrasound beam direction only. To circumvent these limitations, the method presented in this paper uses 3 techniques: 1......) The ultrasound is not focused during the transmissions of the ultrasound signals; 2) A 13-bit Barker code is transmitted simultaneously from each transducer element; and 3) The 2-D vector velocity of the blood is estimated using 2-D cross-correlation. A parameter study was performed using the Field II program......, and performance of the method was investigated when a virtual blood vessel was scanned by a linear array transducer. An improved parameter set for the method was identified from the parameter study, and a flow rig measurement was performed using the same improved setup as in the simulations. Finally, the common...

  13. Preliminary Simulation of Beam Extraction for the 28 GHz ECR Ion Source

    CERN Document Server

    Park, Bum-Sik; Choi, Seokjin

    2015-01-01

    The 28 GHz ECR(Electron Cyclotron Resonance) ion source is under development to supply various beams from proton to uranium at RISP(Rare Isotope Science Project). The superconducting magnet system for a 28 GHz ECR ion source consists of four solenoid coils and a saddle type sextupole. To meet the design requirement of ECR ion source, a numerical simulation was accomplished by using the KOBRA3-INP to optimize the extraction system which is the three dimensional ion optics code. The influence of the three dimensional magnetic field and the space charge effect was considered to extract the highly charged ion beam. In this paper, the design results of the extraction system were reported in detail.

  14. Effect of Reinforcement on Early-Age Concrete Temperature Stress: Preliminary Experimental Investigation and Analytical Simulation

    Directory of Open Access Journals (Sweden)

    Jianda Xin

    2015-01-01

    Full Text Available For concrete under short-term loading, effect of reinforcement on concrete crack resistance capability is usually negligible; however, recent research results show that extension of this viewpoint to concrete under long-term loading (temperature variation may be unsuitable. In order to investigate this phenomenon, this paper presents the experimental and analytical results of early-age reinforced concrete temperature stress development under uniaxial restraint. The experiments were carried out on a temperature stress testing machine (TSTM. Experimental results show that the coupling of reinforcement and concrete creep behavior influenced the concrete temperature stress development, and nearly 16% of concrete stress was reduced in the current research. Moreover, the cracking time of reinforced concrete was also delayed. Finally, based on the principle of superposition, analytical simulations of effect of reinforcement on concrete temperature stress have been performed.

  15. Rimonabant effects on anxiety induced by simulated public speaking in healthy humans: a preliminary report.

    Science.gov (United States)

    Bergamaschi, Mateus M; Queiroz, Regina H C; Chagas, Marcos H N; Linares, Ila M P; Arrais, Kátia C; de Oliveira, Danielle C G; Queiroz, Maria E; Nardi, Antonio E; Huestis, Marilyn A; Hallak, Jaime E C; Zuardi, Antonio W; Moreira, Fabrício A; Crippa, José A S

    2014-01-01

    We investigated the hypothesis that rimonabant, a cannabinoid antagonist/inverse agonist, would increase anxiety in healthy subjects during a simulation of the public speaking test. Participants were randomly allocated to receive oral placebo or 90 mg rimonabant in a double-blind design. Subjective effects were measured by Visual Analogue Mood Scale. Physiological parameters, namely arterial blood pressure and heart rate, also were monitored. Twelve participants received oral placebo and 12 received 90 mg rimonabant. Rimonabant increased self-reported anxiety levels during the anticipatory speech and performance phase compared with placebo. Interestingly, rimonabant did not modulate anxiety prestress and was not associated with sedation, cognitive impairment, discomfort, or blood pressure changes. Cannabinoid-1 antagonism magnifies the responses to an anxiogenic stimulus without interfering with the prestress phase. These data suggest that the endocannabinoid system may work on-demand to counteract the consequences of anxiogenic stimuli in healthy humans. Copyright © 2013 John Wiley & Sons, Ltd.

  16. Two Dimensional Wake Vortex Simulations in the Atmosphere: Preliminary Sensitivity Studies

    Science.gov (United States)

    Proctor, F. H.; Hinton, D. A.; Han, J.; Schowalter, D. G.; Lin, Y.-L.

    1998-01-01

    A numerical large-eddy simulation model is currently being used to quantify aircraft wake vortex behavior with meteorological observables. The model, having a meteorological framework, permits the interaction of wake vortices with environments characterized by crosswind shear, stratification, and humidity. The addition of grid-scale turbulence as an initial condition appeared to have little consequence. Results show that conventional nondimensionalizations work very well for vortex pairs embedded in stably stratified flows. However, this result is based on simple environments with constant Brunt-Vaisala frequency. Results presented here also show that crosswind profiles exert important and complex interactions on the trajectories of wake vortices. Nonlinear crosswind profiles tended to arrest the descent of wake vortex pairs. The member of the vortex pair with vorticity of same sign as the vertical change in the ambient along-track vorticity may be deflected upwards.

  17. Preliminary simulation research of driver behaviour in response to outdoor advertisements

    Directory of Open Access Journals (Sweden)

    Targosiński Tomasz

    2017-01-01

    Full Text Available Advertisements placed near roads can pose a hazard to road safety because they attract the driver’s attention. Many attempts to describe and reduce this impact have been done. However, existing regulations treat this problem differently in different countries which demonstrates the significant difficulties in defining and investigating the impact factors of advertisements on driver behaviour. Pilot studies have been done using the eye-tracker and vehicle simulator. Based on the analysis of driver perception in a programmed and repeatable environment an attempt was made to select key factors influencing their attention in terms of the content of advertisements, the size and location in relation to the road and the personality of drivers.

  18. Simulating cultural transmission: preliminary results and their implications for the study of formal variability of material culture in the Central Balkan Neolithic

    Directory of Open Access Journals (Sweden)

    Marko Porčić

    2014-12-01

    Full Text Available In this paper, we adopt the theoretical framework of evolutionary archaeology in order to model and simulate cultural transmission between hypothetical Neolithic sites in Balkans. We simulate neutral cultural transmission in order to compare the simulation results with empirically observed patterns of material culture variability such as traditional archaeological cultures. Our preliminary results show that a series of random local interactions can result in spatial groupings of typologically similar assemblages that correspond to the spatial distributions of traditional archaeological cultures, even in the absence of any other ‘external’ factor such as an overarching regional political structure or shared collective identity.

  19. Numerical simulation of bubble transport in a bifurcating microchannel: a preliminary study.

    Science.gov (United States)

    Poornima, J; Vengadesan, S

    2012-08-01

    In this paper, we present the computational fluid dynamics (CFD) simulations of bubble transport in a first generation bifurcating microchannel. In the present study, the human arteriole is modeled as a two-dimensional (2D) rectangular bifurcating microchannel. The microchannel is filled with blood and a single perfluorocarbon (PFC) bubble is introduced in the parent channel. The simulations are carried out to identify the lodging and dislodging pressures for two nondimensional bubble sizes, L(d) (ratio of the dimensional bubble length to the parent tube diameter), that is for L(d) = 1 and L(d) = 2. Subsequently, the bubble transport and splitting behavior due to the presence of symmetry and asymmetry in the daughter channels of the microchannel is studied for these bubble sizes. The splitting behavior of the bubble under the effect of gravity is also assessed and reported here. For the symmetric bifurcation model, the splitting ratio (SR) (ratio of bubble volume in bottom daughter channel to bubble volume in top daughter channel), of the bubble was found to be 1. For the asymmetric model, the splitting ratio was found to be less than 1. The loss in the bubble volume in the asymmetric model was attributed to surface tension effects and the resistance offered by the flow, which led to the bubble sticking and sliding along the walls of the channel. With the increase in roll angle, Φ (angle which the plane makes with the horizontal to study the effects of gravity), there was a decline in the splitting ratio.

  20. An operational model to simulate post-accidental radionuclide transfers in Toulon marine area: preliminary development

    Science.gov (United States)

    Duffa, Celine; Dufois, Francois; Coudray, Sylvain

    2011-11-01

    As part of its development of post-accident management tools, the French Institute for Radiological Protection and Nuclear Safety is setting up a model to simulate radionuclide dispersion in the Toulon marine area (one of France's main military ports). The model is based on the MARS 3D code developed by IFREMER. It reproduces hydro-sedimentation phenomena in the Bay of Toulon with a horizontal spatial resolution of 100 m and 30 vertical sigma levels and also factors in radioactive decay and dissolved/particulate distribution of the radionuclides studied. With no tide, the major currents in this area are generated by the wind. The model effectively reproduces the resulting hydrodynamic phenomena, which were measured throughout the summer of 2009 in the channel that links the Little Bay to the Large Bay of Toulon. When the Mistral (wind from the West/Northwest) blows, a surface current quickly appears, which pushes water southwards from the Little Bay, and which is offset by a bottom current (upwellings). When the wind blows from the East, the currents move in the opposite direction, and southeasterly waves, dependent on wind strength and fetch, occur in the Large Bay. Here, we give an example of the simulated dispersion of radionuclides released directly into the surface waters near the Arsenal, demonstrating the constraint relative to dispersion generated by the half-closed configuration of the Little Bay. Sediment in the Little Bay also forms an area where the most highly reactive radionuclides would accumulate, and where the lack of waves has the effect of considerably limiting the phenomena of resuspension.

  1. Preliminary Experimental Results of Integrated Gasification Fuel Cell Operation Using Hardware Simulation

    Energy Technology Data Exchange (ETDEWEB)

    Traverso, Alberto; Tucker, David; Haynes, Comas L.

    2012-07-01

    A newly developed integrated gasification fuel cell (IGFC) hybrid system concept has been tested using the Hybrid Performance (Hyper) project hardware-based simulation facility at the U.S. Department of Energy, National Energy Technology Laboratory. The cathode-loop hardware facility, previously connected to the real-time fuel cell model, was integrated with a real-time model of a gasifier of solid (biomass and fossil) fuel. The fuel cells are operated at the compressor delivery pressure, and they are fueled by an updraft atmospheric gasifier, through the syngas conditioning train for tar removal and syngas compression. The system was brought to steady state; then several perturbations in open loop (variable speed) and closed loop (constant speed) were performed in order to characterize the IGFC behavior. Coupled experiments and computations have shown the feasibility of relatively fast control of the plant as well as a possible mitigation strategy to reduce the thermal stress on the fuel cells as a consequence of load variation and change in gasifier operating conditions. Results also provided an insight into the different features of variable versus constant speed operation of the gas turbine section.

  2. OMV man/system simulation integration: A preliminary analysis and recommendation

    Science.gov (United States)

    Rogers, Jon G.

    1988-01-01

    The Orbital Maneuvering Vehicle (OMV) presents a series of challenges to the human operator. Some are unique to the OMV system itself, and are largely due to remote control versus control from the cockpit. Other challenges are not necessarily unique to the OMV, but are characteristic of many man-machine space flight systems. All of these challenges affect the operator's ability to perform his portion of the mission, and could lead to human error which might jeopardize the vehicle, mission, or both. It is imperative to make every effort to design the control and displays to facilitate the operator's task. The experimental program should address the perceptual, mediational, and motor dimensions of operator performance. With this in mind, a literature review with relevant design considerations was initiated, and a comprehensive outline of control/display parameters were developed. Out of this, a series of questions not answered in the literature was derived which can be converted into experimental protocols for the simulation program. A major task of the aircraft pilot as well as the OMV operator is prediction. Certain display principles have proved to enhance the pilot's ability to predict. A brief examination of some of these principles in relationship to OMV may be useful.

  3. 基于AUTODYN的潜艇典型舱段水中爆炸冲击损伤研究%Impact Damage Analysis of Typical Submarine Compartment Subjected to Underwater BlastingBased on AUTODYN

    Institute of Scientific and Technical Information of China (English)

    姜涛; 王桂芹; 詹发民; 周方毅

    2015-01-01

    The damage and deformation of submarine with double shell, in underwater blasting by underwater weapon such as torpedo, were studied based on AUTODYN. For typical submarine compartment,damage and deformation of the submarine hull in explosionhit contact and with standoff distance of 2, 4, 6 m were analyzed. The results show that the shell appears crevasse damage while torpedo contacts blast, the pressure hull appears crevasse and no-pressure hull presents plastic deformation while distance is 2m from the explosion source, and the pressure hull and no- pressure hull has plastic deformation while distance is 4mand 6m from the explosive.%针对双层壳体潜艇在鱼雷等水中兵器爆炸作用下壳体的变形及破损问题,采用AUTODYN有限元软件,分析了潜艇典型舱段,在鱼雷接触命中及爆距分别为2、4、6m条件下,双层壳体潜艇的壳体破口及变形。计算结果表明,潜艇在鱼雷接触命中条件下,耐压及非耐压壳体均出现较大破口,且耐压壳体破口范围更大;在鱼雷2m爆距条件下,潜艇耐压壳体出现较大破口,非耐压壳体出现较大塑性变形;在鱼雷4、6m爆距条件下,耐压及非耐压壳体均有较大塑性变形。

  4. Thermo-hydro-mechanical simulation of a 3D fractured porous rock: preliminary study of coupled matrix-fracture hydraulics

    Energy Technology Data Exchange (ETDEWEB)

    Canamon, I.; Javier Elorza, F. [Universidad Politecnica de Madrid, Dept. de Matematica Aplicada y Metodos Informaticas, ETSI Minas (UPM) (Spain); Ababou, R. [Institut de Mecanique des Fluides de Toulouse (IMFT), 31 (France)

    2007-07-01

    We present a problem involving the modeling of coupled flow and elastic strain in a 3D fractured porous rock, which requires prior homogenization (up-scaling) of the fractured medium into an equivalent Darcian anisotropic continuum. The governing equations form a system of PDE's (Partial Differential Equations) and, depending on the case being considered, this system may involve two different types of 'couplings' (in a real system, both couplings (1) and (2) generally take place): 1) Hydraulic coupling in a single (no exchange) or in a dual matrix-fracture continuum (exchange); 2) Thermo-Hydro-Mechanical interactions between fluid flow, pressure, elastic stress, strain, and temperature. We present here a preliminary model and simulation results with FEMLAB{sup R}, for the hydraulic problem with anisotropic heterogeneous coefficients. The model is based on data collected at an instrumented granitic site (FEBEX project) for studying a hypothetical nuclear waste repository at the Grimsel Test Site in the Swiss Alps. (authors)

  5. Theoretical analyses and numerical simulations of the torsional mode for two acoustic viscometers with preliminary experimental tests.

    Science.gov (United States)

    Ai, Yuhui; Lange, Rebecca A

    2008-03-01

    A rigorous analysis of the torsional modes in both a cylindrical wave guide and the associated static viscous fluid field has been conducted from the solid and the fluid wave equations and the coupled boundary conditions. As a result, two acoustic viscometer models, along with four independent equations connecting the density and the viscosity of the fluid with the attenuation and the phase velocity of the torsional wave in the wave guide, have been developed. The analysis shows that the product of the viscosity and the density of the fluid can be measured from the end reflection coefficient of the torsional wave in the wave guide and that both the viscosity and the density can be determined simultaneously from either the phase velocity or the attenuation of the torsional wave in a single cylindrical wave guide. For the simultaneous measurements of the viscosity and the density, the independent equations have to be solved numerically, for example, using Matlab (The MathWorks, Natick, MA), given either the attenuation or the phase velocity in the wave guide that is surrounded by the fluid. To demonstrate the technical feasibility, numerical simulations have been conducted to discern viscosity, phase velocity, and density, all versus attenuation, at different frequencies, and with variable dimension of a molybdenum rod, so that both the advantages and the disadvantages of the simultaneous measurements can be explored. In the end, to test the two models, preliminary experiments on two viscous standards were conducted at 23 degrees C, and good agreements have been achieved between the viscosities measured from both models and for both standards.

  6. Simulation of Blast and Fragment Loading Usinga Coupled Multi-Solver Approach

    Institute of Scientific and Technical Information of China (English)

    QUAN Xiangyang; GERBER Bence; COWLER Malcolm; BIRNBAUM Naury

    2006-01-01

    Simulating blast and fragment loading simultaneously in a single computation requires the combined use of multiple states of the art solvers.A pipe bomb is an example of simple improvised explosive device (IED) that consists of a piece of pipe filled with explosive material and capped at both ends.To simulate the explosion of a pipe bomb and the damage it causes,a coupled multisolver approach based upon finite element and finite volume methods is applied.The numerical calculation presented demonstrates the ability of ANSYS AUTODYN(R) to correctly simulate the threats of IEDs and provides insight into how the most significant physical phenomena affect the results.

  7. Modeling and Simulation of Ceramic Arrays to Improve Ballaistic Performance

    Science.gov (United States)

    2013-10-01

    are modeled using SPH elements. Model validation runs with monolithic SiC tiles are conducted based on the DoP experiments described in reference...TERMS ,30cal AP M2 Projectile, 762x39 PS Projectile, SPH , Aluminum 5083, SiC, DoP Expeminets, AutoDyn Simulations, Tile Gap 16. SECURITY...Yarlagadda 19b. TELEPHONE NUMBER (include area code ) 302-831-4941 Standard Form 298 (Rev. 8-98) :..-.,.... „.,<-. C((j Z39.18 •MWl^ MONTHLY

  8. Modeling and Simulation of Ceramic Arrays to Improve Ballaistic Performance

    Science.gov (United States)

    2013-09-09

    SUPPLEMENTARY NOTES 14. ABSTRACT -Quarter-symmetric model is used in AutoDyn to simulate DoP experiments on aluminum targets and ceramic-faced aluminum...targets with .30cal AP M2 projectile using SPH elements. -Model validation runs were conducted based on the DoP experiments described in reference...effect of material properties on DoP 15. SUBJECT TERMS .30cal AP M2 Projectile, 762x39 PS Projectile, SPH, Aluminum 5083, SiC, DoP Expeminets

  9. Simulations of explosion-induced damage to underground rock chambers

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    A numerical approach is presented to study the explosion-induced pressure load on an underground rock chamber wall and its resultant damage to the rock chamber.Numerical simulations are carried out by using a modified version of the commercial software AUTODYN.Three different criteria,i.e.a peak particle velocity (PPV) criterion,an effective strain (ES) criterion,and a damage criterion,are employed to examine the explosion-induced damaged zones of the underground rock chamber.The results show that the charg...

  10. Preliminary ice shelf-ocean simulation results from idealized standalone-ocean and coupled model intercomparison projects (MIPs)

    Science.gov (United States)

    Asay-Davis, Xylar; Martin, Daniel

    2016-04-01

    The second Ice Shelf-Ocean MIP (ISOMIP+) and the first Marine Ice Sheet-Ocean MIP (MISOMIP1) prescribe a set of idealized experiments for ocean models with ice-shelf cavities and coupled ice sheet-ocean models, respectively. ISOMIP+ and MISOMIP1 were designed together with the third Marine Ice Sheet MIP (MISMIP+) with three main goals, namely that the MIPs should provide: a controlled forum for researchers to compare their model results with those from other models during model development. a path for testing components in the process of developing coupled ice sheet-ocean models. a basic setup from which a large variety of parameter and process studies can usefully be performed. The experimental design for the three MIPs is currently under review in Geoscientific Model Development (Asay-Davis et al. 2015, doi:10.5194/gmdd-8-9859-2015). We present preliminary results from ISOMIP+ and MISOMIP1 experiments using several ocean-only and coupled ice sheet-ocean models. Among ocean models, we show that differences in model behavior are significant enough that similar results can only be achieved by tuning model parameters (e.g. boundary-layer transfer coefficients, drag coefficients, vertical mixing parameterizations) for each models. This tuning is constrained by a desired mean melt rate in quasi-steady state under specified forcing conditions, akin to how models would be tuned based on observations for non-idealized simulations. We also present a number of parameter studies based the MIP experiments. Again, using several models, we show that melt rates respond sub-linearly to both changes in the square root of the drag coefficient and the heat-transfer coefficient, and that melting is relatively insensitive to horizontal-mixing coefficients (perhaps because the resolution is sufficient to permit eddies) but more sensitive to vertical-mixing coefficients. We show that the choice of the equation of state (linear or nonlinear) does not have a significant impact as long as

  11. Analytical and Preliminary Simulation Study of a Pilot's Ability to Control the Terminal Phase of a Rendezvous with Simple Optical Devices and a Timer

    Science.gov (United States)

    Lineberry, Edgar C., Jr.; Brissenden, Roy F.; Kurbjun, Max C.

    1961-01-01

    One method of controlling the terminal phase of a space rendezvous between two vehicles is first to correct the flight path of the controlled vehicle so that a constant line of sight is established between the vehicles. This correction is accomplished by thrusting normal to the sight line in a direction to arrest the angular motion of this line. Once this collision course has been established, the second step is to control the closure rate for a safe approach along the line of sight. Adequate control of this maneuver requires range and closure-rate information. A combined analytical and preliminary simulation study was conducted to determine the ability of a human pilot to control the rendezvous by this method using visual sightings made during the initial collision-course control to obtain the range and closure rate. The analytical phase of the study reviewed the geometric relations between the vehicles and formed the basis for techniques to transform the angular sightings into range and closure rate. A preliminary simulation was then made to investigate the accuracy of these techniques. The simulation consisted of an analog computer, an oscilloscope to represent the view a pilot would have-with a stabilized sight, and a timer. Results indicate that pilots, using an optical sight and a timer, can successfully arrest the angular motion of the line of sight between two rendezvous vehicles and obtain relative range and closure rate with sufficient accuracy to perform the final braking maneuver successfully.

  12. Numerical Simulation of Underwater Explosion Loads

    Institute of Scientific and Technical Information of China (English)

    XIN Chunliang; XU Gengguang; LIU Kezhong

    2008-01-01

    Numerical simulation of TNT underwater explosion was carried out with AUTODYN software.Influences of artificial viscosity and mesh density on simulation results were discussed.Detonation waves in explosive and shock wave in water during early time of explosion are high frequency waves.Fine meshes (less than 1 mm) in explosive and water nearby,and small linear viscosity coefficients and quadratic viscosity coefficients (0.02 and 0.1 respectively,1/10 of default values) are needed in numerical simulation model.According to these rules,numerical computing pressure profiles can match well with those calculated by Zamyshlyayev empirical formula.Otherwise peak pressure would be smeared off and upstream relative errors would be cumulated downstream to make downstream peak pressure lower.

  13. Preliminary Three-Dimensional Simulation of Sediment and Cesium Transport in the Ogi Dam Reservoir using FLESCOT – Task 6, Subtask 2

    Energy Technology Data Exchange (ETDEWEB)

    Onishi, Yasuo; Kurikami, Hiroshi; Yokuda, Satoru T.

    2014-03-28

    After the accident at the Fukushima Daiichi Nuclear Power Plant in March 2011, the Japan Atomic Energy Agency and the Pacific Northwest National Laboratory initiated a collaborative project on environmental restoration. In October 2013, the collaborative team started a task of three-dimensional modeling of sediment and cesium transport in the Fukushima environment using the FLESCOT (Flow, Energy, Salinity, Sediment Contaminant Transport) code. As the first trial, we applied it to the Ogi Dam Reservoir that is one of the reservoirs in the Japan Atomic Energy Agency’s (JAEA’s) investigation project. Three simulation cases under the following different temperature conditions were studied: • incoming rivers and the Ogi Dam Reservoir have the same water temperature • incoming rivers have lower water temperature than that of the reservoir • incoming rivers have higher water temperature than that of the reservoir. The preliminary simulations suggest that seasonal temperature changes influence the sediment and cesium transport. The preliminary results showed the following: • Suspended sand, and cesium adsorbed by sand, coming into the reservoirs from upstream rivers is deposited near the reservoir entrance. • Suspended silt, and cesium adsorbed by silt, is deposited farther in the reservoir. • Suspended clay, and cesium adsorbed by clay, travels the farthest into the reservoir. With sufficient time, the dissolved cesium reaches the downstream end of the reservoir. This preliminary modeling also suggests the possibility of a suitable dam operation to control the cesium migration farther downstream from the dam. JAEA has been sampling in the Ogi Dam Reservoir, but these data were not yet available for the current model calibration and validation for this reservoir. Nonetheless these preliminary FLESCOT modeling results were qualitatively valid and confirmed the applicability of the FLESCOT code to the Ogi Dam Reservoir, and in general to other reservoirs in

  14. Development of a numerical simulator of human swallowing using a particle method (part 1. Preliminary evaluation of the possibility of numerical simulation using the MPS method).

    Science.gov (United States)

    Kamiya, Tetsu; Toyama, Yoshio; Michiwaki, Yukihiro; Kikuchi, Takahiro

    2013-01-01

    The aim of the present study was to evaluate the possibility of numerical simulation of the swallowing process using a moving particle simulation (MPS) method, which defined the food bolus as a number of particles in a fluid, a solid, and an elastic body. In order to verify the accuracy of the simulation results, a simple water bolus falling model was solved using the three-dimensional (3D) MPS method. We also examined the simplified swallowing simulation using a two-dimensional (2D) MPS method to confirm the interactions between the liquid, solid, elastic bolus, and organ structure. In a comparison of the 3D MPS simulation and experiments, the falling time of the water bolus and the configuration of the interface between the liquid and air corresponded exactly to the experimental measurements and the visualization images. The results showed that the accuracy of the 3D MPS simulation was qualitatively high for the simple falling model. Based on the results of the simplified swallowing simulation using the 2D MPS method, each bolus, defined as a liquid, solid, and elastic body, exhibited different behavior when the organs were transformed forcedly. This confirmed that the MPS method could be used for coupled simulations of the fluid, the solid, the elastic body, and the organ structures. The results suggested that the MPS method could be used to develop a numerical simulator of the swallowing process.

  15. Regional hydrogeological simulations. Numerical modelling using ConnectFlow. Preliminary site description Simpevarp sub area - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Hartley, Lee; Hoch, Andrew; Hunter, Fiona; Jackson, Peter [Serco Assurance, Risley (United Kingdom); Marsic, Niko [Kemakta Konsult, Stockholm (Sweden)

    2005-02-01

    objective of this study is to support the development of a preliminary Site Description of the Simpevarp area on a regional-scale based on the available data of August 2004 (Data Freeze S1.2) and the previous Site Description. A more specific objective of this study is to assess the role of known and unknown hydrogeological conditions for the present-day distribution of saline groundwater in the Simpevarp area on a regional-scale. An improved understanding of the paleo-hydrogeology is necessary in order to gain credibility for the Site Description in general and the hydrogeological description in particular. This is to serve as a basis for describing the present hydrogeological conditions on a local-scale as well as predictions of future hydrogeological conditions. Other key objectives were to identify the model domain required to simulate regional flow and solute transport at the Simpevarp area and to incorporate a new geological model of the deformation zones produced for Version S1.2.Another difference with Version S1.1 is the increased effort invested in conditioning the hydrogeological property models to the fracture boremap and hydraulic data. A new methodology was developed for interpreting the discrete fracture network (DFN) by integrating the geological description of the DFN (GeoDFN) with the hydraulic test data from Posiva Flow-Log and Pipe-String System double-packer techniques to produce a conditioned Hydro-DFN model. This was done in a systematic way that addressed uncertainties associated with the assumptions made in interpreting the data, such as the relationship between fracture transmissivity and length. Consistent hydraulic data was only available for three boreholes, and therefore only relatively simplistic models were proposed as there isn't sufficient data to justify extrapolating the DFN away from the boreholes based on rock domain, for example. Significantly, a far greater quantity of hydro-geochemical data was available for calibration in the

  16. Shiga toxin-producing Escherichia coli in meat: a preliminary simulation study on detection capabilities for three sampling methods

    Science.gov (United States)

    The objective of this simulation study is to determine which sampling method (Cozzini core sampler, core drill shaving, and N-60 surface excision) will better detect Shiga Toxin-producing Escherichia coli (STEC) at varying levels of contamination when present in the meat. 1000 simulated experiments...

  17. To accomplish preliminary Qigong simulation state by acupuncture%针刺刺激可达到前气功状态

    Institute of Scientific and Technical Information of China (English)

    何丰名; 丁秀玉; 乔长诚; 郭慧燕; 颜名聪; 郭俊成

    2011-01-01

    The purpose of the study was to find out how to enter the preliminary Qigong simulation state in a short period of time.Methods:This is a non-randomized,human experiment with healthy participants.A multichannel digital physiological data recorder was used to detect whether the participants had entered the Qigong state.Participants were assisted to enter the Qigong state (relaxation,tranquility and naturalness) by being given the sore (sour) feeling produced by acupuncturing Hegu (LI4),and suggestions (repeating words "relax" and "heat" from the hypogastrium).Results:About 72.2% of the participants who had no Qigong experience were found entering the preliminary Qigong simulation state.Most of the physiological parameters measured after the participants entering the Qigong state showed significant changes compared with the baseline data.Conclusion:This study revealed that acupuncture-made sore feeling is able to induce the participants to quickly enter the preliminary Qigong simulation state; hence this can be seen as no longer a limited phenomenon,but can be commonly applied to everybody.%目的:研究在短时间之内使普通人进入前气功状态的方法.方法:健康的试验参与者以不随机的方式纳入本次研究.使用多通道生理记录仪检测试验参与者是否有进入前气功状态.参与者在针刺合谷穴的时候获得酸(得气)的感觉,同时暗示参与者丹田处有热及放松的感觉,由此让参与者进入一个松、静、自然的前气功状态.结果:本研究中,72.2%没有习练气功经历的参与者成功进入前气功状态.参与者进入气功状态后,大部分生理指标与基线指标相比有显著差异.结论:使用针刺引起酸的感觉可以让试验参与者快速进入前气功状态.因此气功的研究不再限制在特定的人才可以实行,本研究方法可以应用到每个人身上.

  18. A preliminary investigation into the use of an auditory brainstem response (ABR) simulator for training audiology students in waveform analysis.

    Science.gov (United States)

    Dzulkarnain, Ahmad Aidil Arafat; Wan Mhd Pandi, Wan Mahirah; Wilson, Wayne J; Bradley, Andrew P; Sapian, Faizah

    2014-08-01

    To determine if a computer simulation can be used to improve the ability of audiology students to analyse ABR waveforms. A pretest-posttest, quasi-experimental design was used. All participants completed a pretraining examination of their ability to analyse ABR waveforms, eight hours of ABR analysis training over eight weeks using one of three training modes-manual, simulator or combined manual and simulator training, and a posttraining examination of their ability to analyse ABR waveforms. Fourteen third-year audiology students (13 female, one male, aged 21 to 22 years) participated in this study. Participants who completed the manual or the combined manual and simulator training achieved significantly higher normalized gain scores on their ABR waveform analysis examinations compared to those who completed the simulator training (p audiology students to analyse ABR waveforms were driven primarily by the manual training. The minimal improvements seen in the students who received the simulator training suggest that face-to-face instruction could be required to enhance the ability of audiology students to analyse ABR waveforms.

  19. Preliminary experimental study and simulation of an energy-tunable quasi-monochromatic laser-Compton X/γ-ray source

    Institute of Scientific and Technical Information of China (English)

    LUO We; XU Wang; ZHUO Hong-Bin; MA Yan-Yun

    2012-01-01

    We propose a slanting collision scheme for Compton scattering of a laser light against a relativistic electron beam.This scheme is suitable to generate an energy-tunable X/γ-ray source.In this paper,we present theoretical study and simulation of the spectral,spatial and temporal characteristics of such a source.We also describe two terms laser-Compton scattering (LCS) experiments at the 100 MeV Linac of Shanghai Institute of Applied Physics,where quasi-monochromatic LCS X-ray energy spectra with peak energies of ~30 keV are observed successfully.These preliminary investigations are carried out to understand the feasibility of developing an energy-tunable quasi-monochromatic X/γ-ray source,the future Shanghai Laser Electron Gamma Source.

  20. Preliminary studies of three dimensional effects on artificial cracks at simulated rocket moter liners by the frozen stress method

    Energy Technology Data Exchange (ETDEWEB)

    Smith, C.W.; Finlayson, E.F. [Virginia Polytechnic Institute and State Univ., Blacksburg, VA (United States); Liu, C.T. [OL/AC/PL/RKS, Edwards Air Force Base, CA (United States)

    1996-12-31

    In a preliminary study limited to stress freezing materials, two types of bimaterial specimens, one consisting of two photoelastic materials with different critical temperatures (Type A) and one consisting of a photoelastic material with and without aluminum powder (the powder added to alter the modulus of elasticity without changing the critical temperature (Type B)) are constructed by bonding two halves of the dissimilar materials together. Each type of specimen contains an artificial edge crack along the bond line and loaded normal to the bond line. After evaluating the two specimen types by measuring the variation of the Mode I stress intensity distribution through the specimen thickness, Type B was selected as a superior model and its features studied in detail.

  1. Building a virtual simulation platform for quasistatic breast ultrasound elastography using open source software: A preliminary investigation.

    Science.gov (United States)

    Wang, Yu; Helminen, Emily; Jiang, Jingfeng

    2015-09-01

    Quasistatic ultrasound elastography (QUE) is being used to augment in vivo characterization of breast lesions. Results from early clinical trials indicated that there was a lack of confidence in image interpretation. Such confidence can only be gained through rigorous imaging tests using complex, heterogeneous but known media. The objective of this study is to build a virtual breast QUE simulation platform in the public domain that can be used not only for innovative QUE research but also for rigorous imaging tests. The main thrust of this work is to streamline biomedical ultrasound simulations by leveraging existing open source software packages including Field II (ultrasound simulator), VTK (geometrical visualization and processing), FEBio [finite element (FE) analysis], and Tetgen (mesh generator). However, integration of these open source packages is nontrivial and requires interdisciplinary knowledge. In the first step, a virtual breast model containing complex anatomical geometries was created through a novel combination of image-based landmark structures and randomly distributed (small) structures. Image-based landmark structures were based on data from the NIH Visible Human Project. Subsequently, an unstructured FE-mesh was created by Tetgen. In the second step, randomly positioned point scatterers were placed within the meshed breast model through an octree-based algorithm to make a virtual breast ultrasound phantom. In the third step, an ultrasound simulator (Field II) was used to interrogate the virtual breast phantom to obtain simulated ultrasound echo data. Of note, tissue deformation generated using a FE-simulator (FEBio) was the basis of deforming the original virtual breast phantom in order to obtain the postdeformation breast phantom for subsequent ultrasound simulations. Using the procedures described above, a full cycle of QUE simulations involving complex and highly heterogeneous virtual breast phantoms can be accomplished for the first time

  2. Preliminary results on molecular modeling of asphaltenes using structure elucidation programs in conjunction with molecular simulation programs

    Energy Technology Data Exchange (ETDEWEB)

    Kowalewski, I.; Vandenbroucke, M.; Huc, A.Y.; Taylor, M.J.; Faulon, J.L. [Institut Francais du Petrole, Rueil-Malmaison (France). Division Geologie-Geochimie

    1996-01-01

    Molecular modeling using structure elucidation programs in conjunction with molecular simulation programs has been performed on asphaltene molecules, the heaviest fraction of crude oil, in order to obtain a chemical model allowing the tentative study of their physicochemical properties. Boscan asphaltenes (Venezuela) derived from a marine source rock have been analysed. The different steps of this molecular modeling are described. First, a 3-D chemical representation of Boscan asphaltene is defined from an analytical data set. Second, the results of molecular dynamic simulations indicate that only a few stable conformations are possible due to the high reticulation of the model of the asphaltene unit obtained. 42 refs., 6 figs., 9 tabs.

  3. Incorporating field wind data into FIRETEC simulations of the International Crown Fire Modeling Experiment (ICFME): preliminary lessons learned

    Science.gov (United States)

    Rodman Linn; Kerry Anderson; Judith Winterkamp; Alyssa Broos; Michael Wotton; Jean-Luc Dupuy; Francois Pimont; Carleton Edminster

    2012-01-01

    Field experiments are one way to develop or validate wildland fire-behavior models. It is important to consider the implications of assumptions relating to the locality of measurements with respect to the fire, the temporal frequency of the measured data, and the changes to local winds that might be caused by the experimental configuration. Twenty FIRETEC simulations...

  4. Hydrodynamical simulation of detonations in superbursts. I. The hydrodynamical algorithm and some preliminary one-dimensional results

    CERN Document Server

    Noel, C; Papalexandris, M V; Deledicque, V; Messoudi, A El

    2007-01-01

    Aims. This work presents a new hydrodynamical algorithm to study astrophysical detonations. A prime motivation of this development is the description of a carbon detonation in conditions relevant to superbursts, which are thought to result from the propagation of a detonation front around the surface of a neutron star in the carbon layer underlying the atmosphere. Methods. The algorithm we have developed is a finite-volume method inspired by the original MUSCL scheme of van Leer (1979). The algorithm is of second-order in the smooth part of the flow and avoids dimensional splitting. It is applied to some test cases, and the time-dependent results are compared to the corresponding steady state solution. Results. Our algorithm proves to be robust to test cases, and is considered to be reliably applicable to astrophysical detonations. The preliminary one-dimensional calculations we have performed demonstrate that the carbon detonation at the surface of a neutron star is a multiscale phenomenon. The length scale ...

  5. Penetration Evaluation of Explosively Formed Projectiles Through Air and Water Using Insensitive Munition: Simulative and Experimental Studies

    Directory of Open Access Journals (Sweden)

    M. Ahmed

    2016-02-01

    Full Text Available The process of formation, flying, penetration of explosively-formed projectiles (EFP and the effect of water on performance of the charge for underwater applications is simulated by Ansysis Autodyn 2D-Hydro code. The main objective of an explosively formed projectile designed for underwater applications is to disintegrate the target at longer standoff distances. In this paper we have simulated the explosively formed projectile from OFHC-Copper liner for 1200 conical angle. The Affect of water on the penetration of EFP is determined by simulations from Ansysis Autodyn 2-D Hydrocode and by varying depth of water from 1CD-5CD. The depth of penetration against steel target is measured experimentally. Flash X-Ray Radiography (FXR is used to capture EFP jet formation and its penetration against target is measured by depth of penetration experiments. Simulation results are compared with experimental results. The difference in simulated and experimental results for depth of penetration is about 7 mm, which lies within favorable range of error. The jet formation captured from FXR is quite clear and jet velocity determined from Flash X-ray radiography is the same as the ones obtained by using other high explosives. Therefore, it is indicated that Insensitive Munition (8701 can be utilized instead of Polymer Bonded Explosives (PBX for air and underwater environments with great reliability and without any hazard.

  6. The Cryogenic AntiCoincidence Detector for the ATHENA X-IFU: Design Aspects by Geant4 Simulation and Preliminary Characterization of the New Single Pixel

    Science.gov (United States)

    Macculi, C.; Argan, A.; D'Andrea, M.; Lotti, S.; Piro, L.; Biasotti, M.; Corsini, D.; Gatti, F.; Orlando, A.; Torrioli, G.

    2016-08-01

    The ATHENA observatory is the second large-class ESA mission, in the context of the Cosmic Vision 2015-2025, scheduled to be launched on 2028 at L2 orbit. One of the two planned focal plane instruments is the X-ray Integral Field Unit (X-IFU), which will be able to perform simultaneous high-grade energy spectroscopy and imaging over the 5 arcmin FoV by means of a kilo-pixel array of transition-edge sensor (TES) microcalorimeters, coupled to a high-quality X-ray optics. The X-IFU sensitivity is degraded by the particle background, induced by primary protons of both solar and cosmic rays' origin and secondary electrons. A Cryogenic AntiCoincidence (CryoAC) TES-based detector, located sensed by Iridium TESs. We currently achieve a TRL = 3-4 at the single-pixel level. We have designed and developed two further prototypes in order to reach TRL = 4. The design of the CryoAC has been also optimized using the Geant4 simulation tool. Here we will describe some results from the Geant4 simulations performed to optimize the design and preliminary test results from the first of the two detectors, 1 cm2 area, made of 65 Ir TESs.

  7. Working as simulated patient has effects on real patient life – Preliminary insights from a qualitative study

    Directory of Open Access Journals (Sweden)

    Simmenroth-Nayda, Anne

    2016-05-01

    Full Text Available Background: Persons who simulate patients during medical education understand the routines and the underlying script of medical consultations better. We aimed to explore how simulated patients (SPs integrated this new understanding into their daily life, how this work affected their private life as patients, and what we can learn from these changes for concepts of empowerment.Design, setting, and participants: A qualitative interview study. All SPs of Göttingen medical school who had been working longer than three semesters (n=14 were invited and agreed to take part in an open interview about their daily experience with real doctors. Documentary method was used to identify the main issues. Several cases were chosen according to maximum contrast and analysed by in-depth analysis to provide vivid examples of how simulations may affect the real life of the SPs as patients.Results: Our analysis revealed three main changes in the behaviour of SPs as real patients. They were more attentive, had a better understanding of the circumstances under which doctors work, and acted more self-confidently. From the selected cases it became apparent that working as a SP may lead to a constant and significant decrease of fear of hospitals and medical procedures or, in other cases, may enable the SPs to develop new abilities for giving feedback, questioning procedures, and explanations for real doctors.Conclusion: working as a simulated patient seems to be well-suited to understand own progression of diseases, to increase self-responsibility and to a confident attitude as patient.

  8. Preliminary results of sequential monitoring of simulated clandestine graves in Colombia, South America, using ground penetrating radar and botany.

    Science.gov (United States)

    Molina, Carlos Martin; Pringle, Jamie K; Saumett, Miguel; Hernández, Orlando

    2015-03-01

    In most Latin American countries there are significant numbers of missing people and forced disappearances, 68,000 alone currently in Colombia. Successful detection of shallow buried human remains by forensic search teams is difficult in varying terrain and climates. This research has created three simulated clandestine burial styles at two different depths commonly encountered in Latin America to gain knowledge of optimum forensic geophysics detection techniques. Repeated monitoring of the graves post-burial was undertaken by ground penetrating radar. Radar survey 2D profile results show reasonable detection of ½ clothed pig cadavers up to 19 weeks of burial, with decreasing confidence after this time. Simulated burials using skeletonized human remains were not able to be imaged after 19 weeks of burial, with beheaded and burnt human remains not being able to be detected throughout the survey period. Horizontal radar time slices showed good early results up to 19 weeks of burial as more area was covered and bi-directional surveys were collected, but these decreased in amplitude over time. Deeper burials were all harder to image than shallower ones. Analysis of excavated soil found soil moisture content almost double compared to those reported from temperate climate studies. Vegetation variations over the simulated graves were also noted which would provide promising indicators for grave detection.

  9. Preliminary Comparison of Reaction Rate theory and Object Kinetic Monte Carlo Simulations of Defect Cluster Dynamics under Irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Stoller, Roger E [ORNL; Golubov, Stanislav I [ORNL; Becquart, C. S. [Universite de Lille; Domain, C. [EDF R& D, Clamart, France

    2006-09-01

    The multiscale modeling scheme encompasses models from the atomistic to the continuum scale. Phenomena at the mesoscale are typically simulated using reaction rate theory (RT), Monte Carlo (MC), or phase field models. These mesoscale models are appropriate for application to problems that involve intermediate length scales ( m to >mm), and timescales from diffusion (~ s) to long-term microstructural evolution (~years). Phenomena at this scale have the most direct impact on mechanical properties in structural materials of interest to nuclear energy systems, and are also the most accessible to direct comparison between the results of simulations and experiments. Recent advances in computational power have substantially expanded the range of application for MC models. Although the RT and MC models can be used simulate the same phenomena, many of the details are handled quite differently in the two approaches. A direct comparison of the RT and MC descriptions has been made in the domain of point defect cluster dynamics modeling, which is relevant to both the nucleation and evolution of radiation-induced defect structures. The relative merits and limitations of the two approaches are discussed, and the predictions of the two approaches are compared for specific irradiation conditions.

  10. Regional hydrogeological simulations for Forsmark - numerical modelling using CONNECTFLOW. Preliminary site description Forsmark area - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Hartley, Lee; Cox, Ian; Hunter, Fiona; Jackson, Peter; Joyce, Steve; Swift, Ben [Serco Assurance, Risley (United Kingdom); Gylling, Bjoern; Marsic, Niko [Kemakta Konsult AB, Stockholm (Sweden)

    2005-05-01

    The Swedish Nuclear Fuel and Waste Management Company (SKB) carries out site investigations in two different candidate areas in Sweden with the objective of describing the in-situ conditions for a bedrock repository for spent nuclear fuel. The site characterisation work is divided into two phases, an initial site investigation phase (IPLU) and a complete site investigation phase (KPLU). The results of IPLU are used as a basis for deciding on a subsequent KPLU phase. On the basis of the KPLU investigations a decision is made as to whether detailed characterisation will be performed (including sinking of a shaft). An integrated component in the site characterisation work is the development of site descriptive models. These comprise basic models in three dimensions with an accompanying text description. Central in the modelling work is the geological model, which provides the geometrical context in terms of a model of deformation zones and the rock mass between the zones. Using the geological and geometrical description models as a basis, descriptive models for other geo-disciplines (hydrogeology, hydro-geochemistry, rock mechanics, thermal properties and transport properties) will be developed. Great care is taken to arrive at a general consistency in the description of the various models and assessment of uncertainty and possible needs of alternative models. Here, a numerical model is developed on a regional-scale (hundreds of square kilometres) to understand the zone of influence for groundwater flow that affects the Forsmark area. Transport calculations are then performed by particle tracking from a local-scale release area (a few square kilometres) to identify potential discharge areas for the site and using greater grid resolution. The main objective of this study is to support the development of a preliminary Site Description of the Forsmark area on a regional-scale based on the available data of 30 June 2004 and the previous Site Description. A more specific

  11. Preliminary observations and simulation of nocturnal variations of airglow temperature and emission rates at Pune (18.5°N), India

    Science.gov (United States)

    Fadnavis, S.; Feng, W.; Shepherd, Gordon G.; Plane, J. M. C.; Sonbawne, S.; Roy, Chaitri; Dhomse, S.; Ghude, S. D.

    2016-11-01

    Preliminary observations of the nocturnal variations of the OH(6-2) and O2b(0-1) nighttime airglow in the mesosphere and lower thermosphere are investigated in the context of tidal influence for the tropical latitude station Pune (18.5°N, 73.85°E). This is the only tropical Spectral Airglow Temperature Imager (SATI) station where the tidal variations of mesosphere and lower thermosphere (MLT) temperature have been determined from ground based SATI observations. The SATI observations obtained since October 2012 reveal the influence of the migrating semidiurnal tides during solstice at this tropical station. There is variability in amplitude and phase obtained from SATI observations. In this paper, SATI observations on 10 Dec 2012 and 3 March 2013 are compared with Whole Atmosphere Community Climate Model (WACCM) simulations. The amplitude of semidiurnal tides is ~25 K/30 K on 10 Dec 2012 during solstice for OH/O2 temperature. During equinox SATI data indicates existence of semidiurnal tide also. The airglow observations are compared with simulations from the WACCM. The model underestimates the amplitude of the semi diurnal tide during equinox (1.6 K/2.7 K at 87 km/96 km) and solstice (~3.8 K/4.8 K at 87 km/96 km) for these days. The reason may be related to dampening of tides in the model due to the effect of strong latitudinal shear in zonal wind. The diurnal variation of airglow emission - which the model simulates well - is related to the vertical advection associated with the tides and downward mixing of atomic oxygen.

  12. Preliminary studies for the Development of S.E.T.U.P. : "Experimental and Theoretical Simulations Useful for Planetology"

    Science.gov (United States)

    Arzoumanian, E.; Es-Sebbar, Et.; Romanzin, C.; Perrier, S.; Bénilan, Y.; Gazeau, M.-C.

    2008-09-01

    This paper presents studies performed in the frame of the SETUP program (a French acronym for Experimental and Theoretical Simulations Useful for Planetology). The final goal of this project is to perform representative simulations of Titan's atmosphere and to be able to determine the physicochemical processes involved in its atmosphere. The simulation experiments will be performed in a reactor where an initial gas mixture will be exposed, for the first time, to both major energy sources (electrons and photons) that are responsible for the chemical evolution of Titan's atmosphere. Thus, the complex chemistry between N atoms and CH3, CH2, CH fragments, issued from electron dissociation of N2 and photodissociation of CH4 respectively, will be initiated. For these simulation experiments, we are planning to use a pulsed excimer KrF laser delivering photons at 248 nm to dissociate methane via a multiphotonic process because the Lyman-α radiation, mainly responsible for the dissociation of this compound in the upper atmosphere, cannot be easily reproduced in the laboratory. A first attempt to check for the energetic equivalence of the two processes - 2 photons at 248 nm vs. one single photon at Lyman-α - has already been performed and a more extensive re-examination of the methane photolysis at both wavelengths has been undertaken. The available literature indeed provides contradictory results for the methane's primary photolytic scheme at Lyman-α and no studies at all have been performed yet to establish the different photolytic decomposition pathways at 248 nm. One has to note that the available literature provides contradictory results for methane's primary photolytic scheme at Lyman-α and no studies at all have been performed yet to establish the different photolytic decomposition pathways at 248 nm. Thus, a re-examination of the methane photolysis at both wavelengths has been undertaken. Photolysis of methane has been carried out using a photochemical classic

  13. Simulations

    CERN Document Server

    Ngada, N M

    2015-01-01

    The complexity and cost of building and running high-power electrical systems make the use of simulations unavoidable. The simulations available today provide great understanding about how systems really operate. This paper helps the reader to gain an insight into simulation in the field of power converters for particle accelerators. Starting with the definition and basic principles of simulation, two simulation types, as well as their leading tools, are presented: analog and numerical simulations. Some practical applications of each simulation type are also considered. The final conclusion then summarizes the main important items to keep in mind before opting for a simulation tool or before performing a simulation.

  14. Computer simulations of comet- and asteroidlike bodies passing through the Venusian atmosphere: Preliminary results on atmospheric and ground shock effects

    Science.gov (United States)

    Roddy, D.; Hatfield, D.; Hassig, P.; Rosenblatt, M.; Soderblom, L.; Dejong, E.

    1992-01-01

    We have completed computer simulations that model shock effects in the venusian atmosphere caused during the passage of two cometlike bodies 100 m and 1000 m in diameter and an asteroidlike body 10 km in diameter. Our objective is to examine hypervelocity-generated shock effects in the venusian atmosphere for bodies of different types and sizes in order to understand the following: (1) their deceleration and depth of penetration through the atmosphere; and (2) the onset of possible ground-surface shock effects such as splotches, craters, and ejecta formations. The three bodies were chosen to include both a range of general conditions applicable to Venus as well as three specific cases of current interest. These calculations use a new multiphase computer code (DICE-MAZ) designed by California Research & Technology for shock-dynamics simulations in complex environments. The code was tested and calibrated in large-scale explosion, cratering, and ejecta research. It treats a wide range of different multiphase conditions, including material types (vapor, melt, solid), particle-size distributions, and shock-induced dynamic changes in velocities, pressures, temperatures (internal energies), densities, and other related parameters, all of which were recorded in our calculations.

  15. Variable-density groundwater flow simulations and particle tracking. Numerical modelling using DarcyTools. Preliminary site description of the Simpevarp area, version 1.1

    Energy Technology Data Exchange (ETDEWEB)

    Follin, Sven [SF GeoLogic AB, Stockholm (Sweden); Stigsson, Martin; Berglund, Sten [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Svensson, Urban [Computer-aided Fluid Engineering AB, Norrkoeping (Sweden)

    2004-12-01

    SKB is conducting site investigations for a high-level nuclear waste repository in fractured crystalline rocks at two coastal areas in Sweden, Forsmark and Simpevarp. The investigations started in 2002 and have been planned since the late 1990s. The work presented here investigates the possibility of using hydrogeochemical measurements in deep boreholes to reduce parameter uncertainty in a regional modelling of groundwater flow in fractured rock. The work was conducted with the aim of improving the palaeohydrogeological understanding of the Simpevarp area and to give recommendations to the preparations of the next version of the Preliminary Site Description (1.2). The study is based on a large number of numerical simulations of transient variable density groundwater flow through a strongly heterogeneous and anisotropic medium. The simulations were conducted with the computer code DarcyTools, the development of which has been funded by SKB. DarcyTools is a flexible porous media code specifically designed to treat groundwater flow and salt transport in sparsely fractured crystalline rock and it is noted that some of the features presented in this report are still under development or subjected to testing and verification. The simulations reveal the sensitivity of the results to different hydrogeological modelling assumptions, e.g. the sensitivity to the initial groundwater conditions at 10,000 BC, the size of the model domain and boundary conditions, and the hydraulic properties of deterministically and stochastically modelled deformation zones. The outcome of these simulations was compared with measured salinities and calculated relative proportions of different water types (mixing proportions) from measurements in two deep core drilled boreholes in the Laxemar subarea. In addition to the flow simulations, the statistics of flow related transport parameters were calculated for particle flowpaths from repository depth to ground surface for two subareas within the

  16. Design, simulation, fabrication, and preliminary tests of 3D CMS pixel detectors for the super-LHC

    Energy Technology Data Exchange (ETDEWEB)

    Koybasi, Ozhan; /Purdue U.; Bortoletto, Daniela; /Purdue U.; Hansen, Thor-Erik; /SINTEF, Oslo; Kok, Angela; /SINTEF, Oslo; Hansen, Trond Andreas; /SINTEF, Oslo; Lietaer, Nicolas; /SINTEF, Oslo; Jensen, Geir Uri; /SINTEF, Oslo; Summanwar, Anand; /SINTEF, Oslo; Bolla, Gino; /Purdue U.; Kwan, Simon Wing Lok; /Fermilab

    2010-01-01

    The Super-LHC upgrade puts strong demands on the radiation hardness of the innermost tracking detectors of the CMS, which cannot be fulfilled with any conventional planar detector design. The so-called 3D detector architectures, which feature columnar electrodes passing through the substrate thickness, are under investigation as a potential solution for the closest operation points to the beams, where the radiation fluence is estimated to reach 10{sup 16} n{sub eq}/cm{sup 2}. Two different 3D detector designs with CMS pixel readout electronics are being developed and evaluated for their advantages and drawbacks. The fabrication of full-3D active edge CMS pixel devices with p-type substrate has been successfully completed at SINTEF. In this paper, we study the expected post-irradiation behaviors of these devices with simulations and, after a brief description of their fabrication, we report the first leakage current measurement results as performed on wafer.

  17. The simulation of transient statistics of the Southern Hemispheric circulation by the GLAS seasonal cycle model: Preliminary results

    Science.gov (United States)

    Straus, D. M.; Shukla, J.

    1984-01-01

    The general circulation of the Southern Hemisphere is quite different from that of the Northern Hemisphere in many important ways. These include the barotropic nature of the stationary waves and the presence of a strong barotropic component to the mean zonal wind, the lack of a strong seasonal dependence of the transient eddies, and the dominant role played by eddies with periods less than 10 days compared to longer period fluctuations. Such differences attest to the importance of the altered nature of the orographic and thermal land-sea forcings in the Southern Hemisphere compared to the Northern Hemisphere. Some of the important features of the Southern Hemisphere circulation as simulated by the GLAS Seasonal Cycle Model (SCM) are presented. The geographical patterns of local variability and their seasonal shifts in the SCM are discussed and compared to observations.

  18. Regional hydrogeological simulations for Forsmark - numerical modelling using DarcyTools. Preliminary site description Forsmark area version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-12-15

    A numerical model is developed on a regional-scale (hundreds of square kilometres) to study the zone of influence for variable-density groundwater flow that affects the Forsmark area. Transport calculations are performed by particle tracking from a local-scale release area (a few square kilometres) to test the sensitivity to different hydrogeological uncertainties and the need for far-field realism. The main objectives of the regional flow modelling were to achieve the following: I. Palaeo-hydrogeological understanding: An improved understanding of the palaeohydrogeological conditions is necessary in order to gain credibility for the site descriptive model in general and the hydrogeological description in particular. This requires modelling of the groundwater flow from the last glaciation up to present-day with comparisons against measured TDS and other hydro-geochemical measures. II. Simulation of flow paths: The simulation and visualisation of flow paths from a tentative repository area is a means for describing the role of the current understanding of the modelled hydrogeological conditions in the target volume, i.e. the conditions of primary interest for Safety Assessment. Of particular interest here is demonstration of the need for detailed far-field realism in the numerical simulations. The motivation for a particular model size (and resolution) and set of boundary conditions for a realistic description of the recharge and discharge connected to the flow at repository depth is an essential part of the groundwater flow path simulations. The numerical modelling was performed by two separate modelling teams, the ConnectFlow Team and the DarcyTools Team. The work presented in this report was based on the computer code DarcyTools developed by Computer-aided Fluid Engineering. DarcyTools is a kind of equivalent porous media (EPM) flow code specifically designed to treat flow and salt transport in sparsely fractured crystalline rock intersected by transmissive

  19. A three-dimensional variational data assimilation system for the South China Sea: preliminary results from observing system simulation experiments

    Science.gov (United States)

    Peng, Shiqiu; Zeng, Xuezhi; Li, Zhijin

    2016-05-01

    A three-dimensional variational data assimilation (3DVAR) system based on the Regional Ocean Modeling System (ROMS) is established for the South China Sea (SCS). A set of Observing System Simulation Experiments (OSSEs) are performed to evaluate the performance of this data assimilation system and investigate the impacts of different types of observations on representation of three-dimensional large-scale circulations and meso-scale eddies in the SCS. The pseudo-observations that are examined include sea surface temperatures (SSTs), sea surface heights (SSHs), sparse temperature/salinity (T/S) profiles, sea surface velocities (SSVs), and sea surface salinities (SSSs). The results show that SSHs can extend their impacts into the subsurface or even the deep ocean while other surface observations only have impacts within surface mixed layer. SSVs have similar impacts though confined to their spatial coverage, suggesting that SSVs could be a substitute of SSHs nearshore where SSHs are of poor quality. Despite their sparseness, the T/S profiles improve the representation of the temperature and salinity structures below the mixed layer, and a combination of T/S profiles with surface observations leads to a better representation of the meso-scale eddies. Based on the OSSE results, an affordable observing network for the SCS in the near future is proposed.

  20. Obstacle avoidance, visual detection performance, and eye-scanning behavior of glaucoma patients in a driving simulator: a preliminary study.

    Directory of Open Access Journals (Sweden)

    Rocío Prado Vega

    Full Text Available The objective of this study was to evaluate differences in driving performance, visual detection performance, and eye-scanning behavior between glaucoma patients and control participants without glaucoma. Glaucoma patients (n = 23 and control participants (n = 12 completed four 5-min driving sessions in a simulator. The participants were instructed to maintain the car in the right lane of a two-lane highway while their speed was automatically maintained at 100 km/h. Additional tasks per session were: Session 1: none, Session 2: verbalization of projected letters, Session 3: avoidance of static obstacles, and Session 4: combined letter verbalization and avoidance of static obstacles. Eye-scanning behavior was recorded with an eye-tracker. Results showed no statistically significant differences between patients and control participants for lane keeping, obstacle avoidance, and eye-scanning behavior. Steering activity, number of missed letters, and letter reaction time were significantly higher for glaucoma patients than for control participants. In conclusion, glaucoma patients were able to avoid objects and maintain a nominal lane keeping performance, but applied more steering input than control participants, and were more likely than control participants to miss peripherally projected stimuli. The eye-tracking results suggest that glaucoma patients did not use extra visual search to compensate for their visual field loss. Limitations of the study, such as small sample size, are discussed.

  1. SPH Simulation of Ballistic Impact on Ceramic Plate

    Directory of Open Access Journals (Sweden)

    Chetan Swaroop

    2013-06-01

    Full Text Available This paper studies the use of smooth particle hydrodynamics (SPH numerical technique to simulate the impact, penetration and perforation of Ceramic plate (Al2O3-99.7% by Lead Round Nose (LRN projectile. The general discussion of the SPH solver is introduced first then AUTODYN 2D simulation of penetration and perforation of ceramic plate. The numerical prediction of the time history of velocity of bullet is investigated for a range of impact velocity between 400m/s to 800m/s and an empirical relation is derived between impact velocity and residual velocity. For this type of problem, the SPH approach can provide significant advantages over more traditional numerical methods.

  2. Appropriate Coupling Solvers for the Numerical Simulation of Rolled Homogeneous Armor Plate Response Subjected to Blast Loading

    Directory of Open Access Journals (Sweden)

    Ahmad Mujahid Ahmad Zaidi

    2013-01-01

    Full Text Available Rolled homogeneous armor (RHA plate subjected to blast loading is a complex problem involving the nonlinear fluid-structure interaction. The numerical techniques using the spatial discretization scheme that has been provided as a solver in the AUTODYN computer code will be used in this study in order to predict the RHA response subjected to explosive (TNT blast loading. The final deflection will be used as a reference in order to identify the suitable solver for both materials RHA and TNT; then the plastic deformation will be chosen in the simulation process. Instead of using the same solver for RHA and TNT domains, the optimization of solver can be achieved if it is only used in an appropriate domain, or in other words, a different domain will be using different solver. The solvers, which were available in AUTODYN, were used in the analysis of impact and explosion or fluid-structure interaction. Therefore, in this paper, we will determine the suitable solver for both materials (TNT and RHA plate, and the appropriate interaction coupling solver will be obtained. Defining TNT and RHA plates using the Arbitrary Lagrangian Eulerian solver has found the best coupling solver for this case study when compared with existing experimental data. This coupling solver will be used for future analysis in simulating blast-loading phenomena.

  3. The 29th September Samoa Islands tsunami: preliminary simulations based on the first focal mechanisms hypotheses and implications of uncertainties in tsunami early warning strategies

    Science.gov (United States)

    Tonini, R.; Pagnoni, G.; Armigliato, A.; Tinti, S.

    2009-12-01

    At 6:48 AM local time (17:48 UTC time) a strong earthquake of magnitude Mw=8.0 occurred less than 200 km south of the Samoa Islands (Western Samoa and American Samoa), triggering a tsunami that was detected by several tide gauges located all around the source area. The areas most affected were the south coasts of Western and American Samoa, where almost 200 persons were killed and run-up heights were measured in excess of 5 meters on several locations along the coast and and the tide gauges reached a maximum peak-to-peak height of about 3 meters near Pago-Pago (American Samoa) and 1.5 meters in front of Apia (Western Samoa) The existence of many tide gauge records is important to support the investigation of the source mechanism. The epicenter of this earthquake is located very close to the point where the Tonga trench turns its direction from northward to westward. Here the Pacific plate moves westward beneath the Australia plate, determining a subduction zone along the north-oriented segment of the trench and a transform zone along the west-oriented segment. The epicenter location in this complex tectonic context makes identifying the fault mechanism responsible for the tsunami generation a non-trivial task. The goal of this preliminary work is testing different fault models based on the focal mechanism solution proposed by USGS, CMT and EMSC for this earthquake, through the comparison between the tide gauge records and the synthetic signals provided by the numerical simulations, and possibly suggesting new source solutions trying to reproduce as better as possible the tsunami recordings. The numerical simulations are computed by means of the UBO-TSUFD code, developed and maintained by the Tsunami Research Team of the University of Bologna, Italy. The code solves the linear and non-linear shallow water equations and can compute inundation inland. Furthermore the computational domain can be split in grids of different space resolution in order to have more

  4. Simulating Transient Effects of Pulsed Beams on Beam Intercepting Devices

    CERN Document Server

    Richter, Herta; Noah Messomo, Etam

    2011-01-01

    The development in the physics community towards higher beam power through the possibilities of particle accelerators lead to challenges for the developers of elements which are exposed to effect of particle beams (beam intercepting devices = BIDs). For the design of BIDs, the increasing heat load onto these devices due to energetic and focused beams and - in most cases - their highly pulsed nature has to be taken into account. The physics requirements are sometimes opposed to the current state of the art. As one possibility of many in combining the different aspects for these ambitious demands, two highly developed computer programs, namely FLUKA and ANSYS AUTODYN, were joined for this dissertation. The former is a widely enhanced Monte-Carlo-code which specializes on the interaction of particles with static matter, while the latter is a versatile explicit code for the simulation of highly dynamic processes. Both computer programs were developed intensively over years and are still continuously enhanced in o...

  5. Validation of the TRACE code for the system dynamic simulations of the molten salt reactor experiment and the preliminary study on the dual fluid molten salt reactor

    Energy Technology Data Exchange (ETDEWEB)

    He, Xun

    2016-06-14

    one is about the demonstration of a new MSR concept using the mathematic tools. In particular, the aim of the first part is to demonstrate the suitability of the TRACE code for the similar MSR designs by using a modified version of the TRACE code to implement the simulations for the steady-state, transient and accidental conditions. The basic approach of this part is to couple the thermal-hydraulic model and the modified point-kinetic model. The equivalent thermal-hydraulic model of the MSRE was built in 1D with three loops including all the critical main components. The point-kinetic model was improved through considering the precursor drift in order to produce more practical results in terms of the delayed neutron behavior. Additionally, new working fluids, namely the molten salts, were embedded into the source code of TRACE. Most results of the simulations show good agreements with the ORNL's reports and with another recent study and the errors were predictable and in an acceptable range. Therefore, the necessary code modification of TRACE appears to be successful and the model will be refined and its functions will be extended further in order to investigate new MSR design. Another part of this thesis is to implement a preliminary study on a new concept of molten salt reactor, namely the Dual Fluid Reactor (DFR). The DFR belongs to the group of the molten salt fast reactors (MSFR) and it is recently considered to be an option of minimum-waste and inherently safe operation of the nuclear reactors in the future. The DFR is using two separately circulating fluids in the reactor core. One is the fuel salt based on the mixture of tri-chlorides of uranium and plutonium (UCl{sub 3}-PuCl{sub 3}), while another is the coolant composed of the pure lead (Pb). The current work focuses on the basic dynamic behavior of a scaled-down DFR with 500 MW thermal output (DFR-500) instead of its reference design with 3000 MW thermal output (DFR-3000). For this purpose 10 parallel

  6. Preliminary results of simulation of hypo magnetic conditions and variations in energetic range of cosmic rays in ground-based experiments on plant objects

    Science.gov (United States)

    Belisheva, Natalia; Petrashova, Dina; Shchegolev, Boris

    The most dangerous for the astronauts and cosmonauts are the cosmic rays and drastic decrease of the tension of geomagnetic field (GMF) on the Earth orbit and in the open space. The tension in the interplanetary magnetic field is 10 nT, whereas the tension of GMF is 10 (4) nT on the Earth surface. We carried out the preliminary experiments for study the effects of hypo magnetic conditions and variations in energetic range of cosmic rays (CR) on the plant objects (Vigna radiata, Phaseolus vulgaris, Allium cepa and A. fistulosum, Cucumis sativis). GMF was weakened by using special shielding chamber made on the basis of the amorphous alloy magnetic material. The camera is able to weaken the GMF from 48 μT till 0.192 μT. Modulation of the energetic range of the neutron component of secondary CR was performed with using of the shielding by graphite and by paraffin. The influence of hypo magnetic field and the neutron intensity were studied on the germination of seeds, the growth, the length and the side branches of the roots in the experimental samples. We found that the sensitivity to the hypo magnetic field and to the variations in energetic range of neutrons can vary from object to object. For instance, exposure of the hypo magnetic field on black bean and mung bean stimulated the growth of the roots while do not affect on the white bean. Likewise sensitivity of Phaseolus vulgaris (black and white bean) and Vigna radiata (mung bean) to exposure of nucleon component of cosmic rays on the Earth's surface are differed. It was found that modification of energetic range of CR by using graphite shielding leads to a change in sign of correlation between the length of roots in all experimental samples and the nucleon component of CR compared with the control samples. This is evidence that physiology of biological objects significantly are modified in hypo magnetic environment, as well as under exposure of the CR in different energetic ranges during the space flights. Our

  7. Simulated water budgets and ground-water/surface-water interactions in Bushkill and parts of Monocacy Creek watersheds, Northampton County, Pennsylvania--a preliminary study with identification of data needs

    Science.gov (United States)

    Risser, Dennis W.

    2006-01-01

    This report, prepared in cooperation with the Department of Environmental Protection, Office of Mineral Resources Management, provides a preliminary analysis of water budgets and generalized ground-water/surface-water interactions for Bushkill and parts of Monocacy Creek watersheds in Northampton County, Pa., by use of a ground-water flow model. Bushkill Creek watershed was selected for study because it has areas of rapid growth, ground-water withdrawals from a quarry, and proposed stream-channel modifications, all of which have the potential for altering ground-water budgets and the interaction between ground water and streams. Preliminary 2-dimensional, steady-state simulations of ground-water flow by the use of MODFLOW are presented to show the status of work through September 2005 and help guide ongoing data collection in Bushkill Creek watershed. Simulations were conducted for (1) predevelopment conditions, (2) a water table lowered for quarry operations, and (3) anthropogenic changes in hydraulic conductivity of the streambed and aquifer. Preliminary results indicated under predevelopment conditions, the divide between the Bushkill and Monocacy Creek ground-water basins may not have been coincident with the topographic divide and as much as 14 percent of the ground-water discharge to Bushkill Creek may have originated from recharge in the Monocacy Creek watershed. For simulated predevelopment conditions, Schoeneck Creek and parts of Monocacy Creek were dry, but Bushkill Creek was gaining throughout all reaches. Simulated lowering of the deepest quarry sump to an altitude of 147 feet for quarry operations caused ground-water recharge and streamflow leakage to be diverted to the quarry throughout about 14 square miles and caused reaches of Bushkill and Little Bushkill Creeks to change from gaining to losing streams. Lowering the deepest quarry sump to an altitude of 100 feet caused simulated ground-water discharge to the quarry to increase about 4 cubic feet

  8. Simulation

    DEFF Research Database (Denmark)

    Gould, Derek A; Chalmers, Nicholas; Johnson, Sheena J

    2012-01-01

    Recognition of the many limitations of traditional apprenticeship training is driving new approaches to learning medical procedural skills. Among simulation technologies and methods available today, computer-based systems are topical and bring the benefits of automated, repeatable, and reliable p...... performance assessments. Human factors research is central to simulator model development that is relevant to real-world imaging-guided interventional tasks and to the credentialing programs in which it would be used.......Recognition of the many limitations of traditional apprenticeship training is driving new approaches to learning medical procedural skills. Among simulation technologies and methods available today, computer-based systems are topical and bring the benefits of automated, repeatable, and reliable...

  9. Simulation

    CERN Document Server

    Ross, Sheldon

    2006-01-01

    Ross's Simulation, Fourth Edition introduces aspiring and practicing actuaries, engineers, computer scientists and others to the practical aspects of constructing computerized simulation studies to analyze and interpret real phenomena. Readers learn to apply results of these analyses to problems in a wide variety of fields to obtain effective, accurate solutions and make predictions about future outcomes. This text explains how a computer can be used to generate random numbers, and how to use these random numbers to generate the behavior of a stochastic model over time. It presents the statist

  10. 摆杆机构风载模拟试验的初步研究%Preliminary Study on the Wind Load Simulation Test of Rocker Mechanism

    Institute of Scientific and Technical Information of China (English)

    赵海; 高亚东; 杜宗禄

    2013-01-01

      对摆杆机构风载模拟试验进行初步研究,提出一种模拟摆杆机构实际风载的试验方法,即通过摆杆竖立上下摆动模拟稳变风载,反向增加加载油缸模拟瞬变风载。通过试验验证了该方法简单、成本较低且合理可行,可作为后续相关产品模拟风载试验的参考。%  The wind load simulation test of rocker mechanism is studied preliminarily in this paper, and a test method of simulating the actual wind load of rocker mechanism is put forward, namely, simulating the constant wind load by swinging the rocker up and down and simulating the transient wind load by increasing the loading cylinder in reverse direction. The test proves that the method is simple, low-cost, reasonable and practicable, and can be taken as the reference for follow-up wind load simulation tests of relevant mechanisms.

  11. Simulator sickness when performing gaze shifts within a wide field of view optic flow environment: preliminary evidence for using virtual reality in vestibular rehabilitation

    Directory of Open Access Journals (Sweden)

    Whitney Susan L

    2004-12-01

    Full Text Available Abstract Background Wide field of view virtual environments offer some unique features that may be beneficial for use in vestibular rehabilitation. For one, optic flow information extracted from the periphery may be critical for recalibrating the sensory processes used by people with vestibular disorders. However, wide FOV devices also have been found to result in greater simulator sickness. Before a wide FOV device can be used in a clinical setting, its safety must be demonstrated. Methods Symptoms of simulator sickness were recorded by 9 healthy adult subjects after they performed gaze shifting tasks to locate targets superimposed on an optic flow background. Subjects performed 8 trials of gaze shifting on each of the six separate visits. Results The incidence of symptoms of simulator sickness while subjects performed gaze shifts in an optic flow environment was lower than the average reported incidence for flight simulators. The incidence was greater during the first visit compared with subsequent visits. Furthermore, the incidence showed an increasing trend over the 8 trials. Conclusion The performance of head unrestrained gaze shifts in a wide FOV optic flow environment is tolerated well by healthy subjects. This finding provides rationale for testing these environments in people with vestibular disorders, and supports the concept of using wide FOV virtual reality for vestibular rehabilitation.

  12. Preliminary results of the ion extraction simulations applied to the MONO1000 and SUPERSHyPIE electron cyclotron resonance ion sources.

    Science.gov (United States)

    Pierret, C; Maunoury, L; Biri, S; Pacquet, J Y; Tuske, O; Delferriere, O

    2008-02-01

    The goal of this article is to present simulations on the extraction from an electron cyclotron resonance ion source (ECRIS). The aim of this work is to find out an extraction system, which allows one to reduce the emittances and to increase the current of the extracted ion beam at the focal point of the analyzing dipole. But first, we should locate the correct software which is able to reproduce the specific physics of an ion beam. To perform the simulations, the following softwares have been tested: SIMION 3D, AXCEL, CPO 3D, and especially, for the magnetic field calculation, MATHEMATICA coupled with the RADIA module. Emittance calculations have been done with two types of ECRIS: one with a hexapole and one without a hexapole, and the difference will be discussed.

  13. Preliminary results of the ion extraction simulations applied to the MONO1000 and SUPERSHyPIE electron cyclotron resonance ion sourcesa)

    Science.gov (United States)

    Pierret, C.; Maunoury, L.; Biri, S.; Pacquet, J. Y.; Tuske, O.; Delferriere, O.

    2008-02-01

    The goal of this article is to present simulations on the extraction from an electron cyclotron resonance ion source (ECRIS). The aim of this work is to find out an extraction system, which allows one to reduce the emittances and to increase the current of the extracted ion beam at the focal point of the analyzing dipole. But first, we should locate the correct software which is able to reproduce the specific physics of an ion beam. To perform the simulations, the following softwares have been tested: SIMION 3D, AXCEL, CPO 3D, and especially, for the magnetic field calculation, MATHEMATICA coupled with the RADIA module. Emittance calculations have been done with two types of ECRIS: one with a hexapole and one without a hexapole, and the difference will be discussed.

  14. TU-EF-204-10: A Preliminary Study Evaluating Calculation Variations of Local Noise Power Spectra for CT Simulation in Radiation Therapy

    Energy Technology Data Exchange (ETDEWEB)

    Dolly, S [Washington University School of Medicine, Saint Louis, MO (United States); University of Missouri, Columbia, MO (United States); Chen, H; Anastasio, M; Mutic, S; Li, H [Washington University School of Medicine, Saint Louis, MO (United States)

    2015-06-15

    Purpose: Local noise power spectrum (NPS) properties are significantly affected by calculation variables and CT acquisition and reconstruction parameters, but a thoughtful analysis of these effects is absent. In this study, we performed a complete analysis of the effects of calculation and imaging parameters on the NPS. Methods: The uniformity module of a Catphan phantom was scanned with a Philips Brilliance 64-slice CT simulator using various scanning protocols. Images were reconstructed using both FBP and iDose4 reconstruction algorithms. From these images, local NPS were calculated for regions of interest (ROI) of varying locations and sizes, using four image background removal methods. Additionally, using a predetermined ground truth, NPS calculation accuracy for various calculation parameters was compared for computer simulated ROIs. A complete analysis of the effects of calculation, acquisition, and reconstruction parameters on the NPS was conducted. Results: The local NPS varied with ROI size and image background removal method, particularly at low spatial frequencies. The image subtraction method was the most accurate according to the computer simulation study, and was also the most effective at removing low frequency background components in the acquired data. However, first-order polynomial fitting using residual sum of squares and principle component analysis provided comparable accuracy under certain situations. Similar general trends were observed when comparing the NPS for FBP to that of iDose4 while varying other calculation and scanning parameters. However, while iDose4 reduces the noise magnitude compared to FBP, this reduction is spatial-frequency dependent, further affecting NPS variations at low spatial frequencies. Conclusion: The local NPS varies significantly depending on calculation parameters, image acquisition parameters, and reconstruction techniques. Appropriate local NPS calculation should be performed to capture spatial variations of

  15. Validation of analysis methods to simulate national and international impact experiments. Final report; Validierung von Analysemethoden zur Simulation von Aufprallversuchen im In- und Ausland. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Heckoetter, C.; Sievers, J.

    2012-08-15

    Within the framework of project RS1182 on ''Validierung von Analysemethoden zur Simulation von Aufprallversuchen im In- und Ausland'' the examination of different mechanical phenomena which might occur during the impact of deformable, rigid or liquid-filled missiles on robust structures was carried out. The safety-related significance of the work lies in the evaluation of the accuracy of analysis methods employed for the assessment of the load-bearing capacity of building structures subjected to intentional external hazards. In the process, simulations of selected impact tests were conducted with the analysis code ANSYS AUTODYN. Key subject of the tasks was the examination of impact tests with reinforced concrete target structures, including intermediate-scaled tests (carried out at VTT) as well as almost full-scaled tests (carried out in Meppen and at SNL). Besides the behaviour of the missiles especially the description of the damage processes of the reinforced concrete structures constituted a priority. The relevant damage mechanisms include global bending and crack formation, local concrete scabbing and spalling, punching, penetration of missile and perforation. Furthermore, effects of liquid infill of missiles on the load-time-function and structural damage were investigated. By means of bilateral co-operations with organisations at home and abroad test results were exchanged. Further, selective comparative calculations carried out within the IRIS2010 activity of the WGIAGE of CSNI of the OECD/NEA and within the frame of the VTT IMPACT project contributed to the enhancement of the accuracy of statements of the employed analysis methods. For the characterisation of impact loaded concrete the RHT-model was comprehensively tested. Basically, the simulation of the behaviour of reinforced concrete structures under impact loading exhibits dependencies on physical and numerical modelling parameters, which could also be concluded from the

  16. A Preliminary Jupiter Model

    CERN Document Server

    Hubbard, W B

    2016-01-01

    In anticipation of new observational results for Jupiter's axial moment of inertia and gravitational zonal harmonic coefficients from the forthcoming Juno orbiter, we present a number of preliminary Jupiter interior models. We combine results from ab initio computer simulations of hydrogen-helium mixtures, including immiscibility calculations, with a new nonperturbative calculation of Jupiter's zonal harmonic coefficients, to derive a self-consistent model for the planet's external gravity and moment of inertia. We assume helium rain modified the interior temperature and composition profiles. Our calculation predicts zonal harmonic values to which measurements can be compared. Although some models fit the observed (pre-Juno) second- and fourth-order zonal harmonics to within their error bars, our preferred reference model predicts a fourth-order zonal harmonic whose absolute value lies above the pre-Juno error bars. This model has a dense core of about 12 Earth masses, and a hydrogen-helium-rich envelope with...

  17. A Preliminary Jupiter Model

    Science.gov (United States)

    Hubbard, W. B.; Militzer, B.

    2016-03-01

    In anticipation of new observational results for Jupiter's axial moment of inertia and gravitational zonal harmonic coefficients from the forthcoming Juno orbiter, we present a number of preliminary Jupiter interior models. We combine results from ab initio computer simulations of hydrogen-helium mixtures, including immiscibility calculations, with a new nonperturbative calculation of Jupiter's zonal harmonic coefficients, to derive a self-consistent model for the planet's external gravity and moment of inertia. We assume helium rain modified the interior temperature and composition profiles. Our calculation predicts zonal harmonic values to which measurements can be compared. Although some models fit the observed (pre-Juno) second- and fourth-order zonal harmonics to within their error bars, our preferred reference model predicts a fourth-order zonal harmonic whose absolute value lies above the pre-Juno error bars. This model has a dense core of about 12 Earth masses and a hydrogen-helium-rich envelope with approximately three times solar metallicity.

  18. Numerical Simulation and Experimental Research on the Initiation of Explosive Reactive Armor Impacted by Jet at Large Stand-Off%大炸高下射流冲击反应装甲的数值模拟与试验研究

    Institute of Scientific and Technical Information of China (English)

    姚斯瀚; 米双山

    2016-01-01

    基于 AUTODYN-2D 软件分别对某自寻的导弹串联战斗部前级射流在大炸高时的性能和其侵彻过程进行仿真研究,并进行试验验证。仿真结果表明:超过有利炸高后,随着入射角度的增加,侵彻难度增大,但仍具有一定的侵彻能力。射流可以作为前级装药继续研究,为下一步装药的改进设计奠定基础。%Based on the AUTODYN-2D software, a simulation study is conducted on the performance of the front jet of a homing missile tandem warhead,and also on that of the impact initiation to ERA at large stand-off with experiment.The mechanism and interference effect on the jet over favorable stand-off with different angle of incidence are obtained.Comparison is made of the effects of different initiation conditions,and the conclusion is that the jet in a certain range of stand-off still has strong penetration ability.This research lays the foundation for further improving the shaped charge structure.

  19. Organic tank safety project: Preliminary results of energetics and thermal behavior studies of model organic nitrate and/or nitrite mixtures and a simulated organic waste

    Energy Technology Data Exchange (ETDEWEB)

    Scheele, R.D.; Sell, R.L.; Sobolik, J.L.; Burger, L.L.

    1995-08-01

    As a result of years of production and recovery of nuclear defense materials and subsequent waste management at the Hanford Site, organic-bearing radioactive high-level wastes (HLW) are currently stored in large (up to 3. ML) single-shell storage tanks (SSTs). Because these wastes contain both fuels (organics) and the oxidants nitrate and nitrite, rapid energetic reactions at certain conditions could occur. In support of Westinghouse Hanford Company`s (WHC) efforts to ensure continued safe storage of these organic- and oxidant-bearing wastes and to define the conditions necessary for reactions to occur, we measured the thermal sensitivities and thermochemical and thermokinetic properties of mixtures of selected organics and sodium nitrate and/or nitrite and a simulated Hanford organic-bearing waste using thermoanalytical technologies. These thermoanalytical technologies are used by chemical reactivity hazards evaluation organizations within the chemical industry to assess chemical reaction hazards.

  20. Preliminary Monthly Climatological Summaries

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Preliminary Local Climatological Data, recorded since 1970 on Weather Burean Form 1030 and then National Weather Service Form F-6. The preliminary climate data pages...

  1. Preliminary thermal-hydraulic design and simulation for hybrid breeder blanket%聚变-快裂变增殖堆包层初步热工水力学设计分析

    Institute of Scientific and Technical Information of China (English)

    王小勇; 栗再新; 赵奉超; 赵周; 武兴华; 王琦杰

    2014-01-01

    Thermal-hydraulic design and analysis for the new conceptual design of fusion-fission breeding reactor using casing pipes for fuel assembly was done. Based on typical thermal-hydraulic design parameters, preliminary thermal-hydraulic design for the blanket was proposed. The corresponding temperature distribution and pressure distribution were obtained using thermal-hydraulic codes, CFX. The simulation results showed that maximum temperature of the materials were all below their corresponding temperature limits, coolant temperature at the outlet was higher than 773℃, and pressure drop of the coolant could satisfy engineering requirement. The reasonability of this thermal-hydraulic design was preliminarily verified.%对新提出的套管结构聚变-快裂变增殖堆包层概念设计方案进行了热工水力学分析和设计,给出了典型的热工设计参数,并结合大型热工水力学软件CFX对其进行了温度场和压力分布的模拟分析。分析结果表明,材料温度均已低于许用温度,冷却剂出口温度高于773K,冷却剂压降也符合工程上的要求,初步验证了增殖堆包层设计的合理性。

  2. Preliminary Effects of Real-World Factors on the Recovery and Exploitation of Forensic Impurity Profiles of a Nerve-Agent Simulant from Office Media

    Energy Technology Data Exchange (ETDEWEB)

    Fraga, Carlos G.; Sego, Landon H.; Hoggard, Jamin C.; Perez Acosta, Gabriel A.; Viglino, Emilie A.; Wahl, Jon H.; Synovec, Robert E.

    2012-12-28

    Dimethyl methylphosphonate (DMMP) was used as a chemical threat agent (CTA) simulant for a first look at the effects of real-world factors on the recovery and exploitation of a CTA’s impurity profile for source matching. Four stocks of DMMP having different impurity profiles were disseminated as aerosols onto cotton, painted wall board, and nylon coupons according to a thorough experimental design. The DMMP-exposed coupons were then solvent extracted and analyzed for DMMP impurities by comprehensive 2-D gas chromatography/mass spectrometry (GC×GC/MS). The similarities between the coupon DMMP impurity profiles and the known (reference) DMMP profiles were measured by dot products of the coupon profiles and known profiles and by score values obtained from principal component analysis. One stock, with a high impurity-profile selectivity value of 0.9 out of 1, had 100% of its respective coupons correctly classified and no false positives from other coupons. Coupons from the other three stocks with low selectivity values (0.0073, 0.012, and 0.018) could not be sufficiently distinguished from one another for reliable matching to their respective stocks. The results from this work support that: (1) extraction solvents, if not appropriately selected, can have some of the same impurities present in a CTA reducing a CTA’s useable impurity profile, (2) low selectivity among a CTA’s known impurity profiles will likely make definitive source matching impossible in some real-world conditions, (3) no detrimental chemical-matrix interference was encountered during the analysis of actual office media, (4) a short elapsed time between release and sample storage is advantageous for the recovery of the impurity profile because it minimizes volatilization of forensic impurities, and (5) forensic impurity profiles weighted towards higher volatility impurities are more likely to be altered by volatilization following CTA exposure.

  3. A preliminary study on numerical simulation of microwave heating process for chemical reaction and discussion of hotspot and thermal runaway phe-nomenon

    Institute of Scientific and Technical Information of China (English)

    ZHAO Xiang; HUANG KaMa; YAN LiPing; YAO Yuan

    2009-01-01

    The nonlinear process of microwave heating chemical reaction is studied by means of numerical simulation. Especially, the variation of temperature in terms of space and time, as well as the hotspot and thermal runaway phenomena are discussed. Suppose the heated object is a cylinder and the inci-dent electromagnetic (EM) wave is plane wave, the problem turns out to be a coupling calculation of 2D multi-physical fields. The integral equation of EM field is solved using the method of moment (MoM) and the thermal conduction equation is solved using a semi-analysis method. Moreover, a method to determine the equivalent complex permittivity of reactant under the heating is presented in order to perform the calculation. The numerical results for water and a dummy chemical reaction (A) show that the hotspot is a ubiquitous phenomenon in microwave heating process. When the radius of the heated object is small, the highest temperature occurs somewhere inside the object due to the concentration of the EM wave. While the radius increases to a certain degree, the highest temperature occurs some-where close to the surface due to the skin effect, and the whole high temperature area shows cres-cant-shaped. That is in accordance with basic physical principles, if the radius is kept the same in the heating process, the hotspot position of water does not change, while that of reaction A with several radius values varies. For either water or A, the thermal runaway phenomenon in which small difference of radius results in large difference of highest temperature, occurs easily when the radius is small. On the contrary, it is not evident when the radius is large. Moreover, it is notable that the highest tern-perature in water shows oscillating decreasing trend with the increase of radius, but in reaction A al-most decreases monotonously. Further study should be performed to determine if this difference is only an occasional occurrence.

  4. Preliminary simulations of planned experiments to study the impact of trace gases on the capacity of the Weyburn-Midale field to store carbon dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Carroll, S; Hao, Y

    2009-11-13

    oxidized to H{sub 2}SO{sub 4} causing enhanced dissolution of carbonate minerals and some sulfate mineral precipitation. Low pH results in higher mineral solubility and faster dissolution rates and is thought to enhance porosity and permeability near the injection well when trace amounts of SO{sub 2} is injected with CO{sub 2}. The impact of H{sub 2}S on storage reservoir performance appears to more subtle. Knauss et al (2005) report no significant impacts of injection of CO{sub 2} gas streams with and without H{sub 2}S (1 M Pascal H{sub 2}S + 8.4 M Pascal CO{sub 2}) in simulations of CO{sub 2} storage in the Frio sandstone formation. Geochemical reactions for H{sub 2}S impurities include enhance field alkalinity and reaction with iron bearing minerals that may delay breakthrough of H{sub 2}S relative to CO{sub 2}. Emberley et al. (2005) report that half of the alkalinity measured at monitoring wells at the Weyburn-Midale field is due to HS{sup -}. Schoonen and Xu (2004) report that H{sub 2}S can be sequestered as pyrite in sandstones and carbonates by dissolving iron hydroxides and iron-bearing clays. Similarly, Gunter et al (2000) propose the that siderite converts to iron sulfides when it is reacted with H{sub 2}S. The geochemical reactions between H{sub 2}S and iron bearing minerals together with the high solubility of H{sub 2}S relative to CO{sub 2} may contribute to the delayed break though of H{sub 2}S in experiments. A few core flood experiments have shown that the injection of supercritical CO{sub 2} into carbonate aquifers has the potential to significantly alter the porosity in the absence of trace gases such as SO{sub 2} and H{sub 2}S. Luquot and Gouze (2009) documented a 2% porosity increase in carbonate cores when rock-water interactions were transport limited and solution concentrations were closer to equilibrium and a 4% porosity increase when rock-water interactions were reaction limited and solution compositions were further from equilibrium. Similarly Le

  5. Preliminary Report: Results of Computed Tracer Concentrations over Eastern China, South Korea, and Japan for 01 March to 30 May 2007 Daily Simulated Releases from Taiyuan, China

    Energy Technology Data Exchange (ETDEWEB)

    Vogt, P

    2007-08-07

    In order to prepare for a proposed long range tracer experiment in China for the spring of 2008 time period, NARAC computed hypothetical PMCH concentrations over Eastern China, South Korea and Japan for simulated releases from Taiyuan, China. Normalized 1 kg of PMCH source strength releases were made twice a day, with wind input from global forecast weather model. We used 6-hour analysis fields valid at the start of each model run, resulting in four wind fields per day. The selected domain encompassed the region of interest over eastern Asia and the Western Pacific. Screening runs were made for each day at 0000 and 1200 UTC from 01 April, 2007 through 29 May, 2007 for a total of 90 days and 180 cases. 24-hour average air concentrations were evaluated at 22 sample cities in the three regions of interest for each case. 15 sample cities were selected to help quantify modeling results for experiment objectives. Any case that resulted in model predicted air concentrations exceeding 2.0E-02 fL/L at a sample city in all three regions was then selected for a detailed model run with source times six hours before and after evaluated in addition to the case time. The detailed runs used the same wind fields and model domain, but 6-hour average air concentrations were generated and analyzed for the 15 sample cities. Each of the 180 cases were ranked subjectively, based on whether or not the model prediction indicated the possibility that a release on that date and time might achieve the long range experiment objectives. Ranks used are High, Good, Low, Poor, and Bad. Of the 180 cases run, NARAC dispersion models predicted 6 instances of High possibility, 8 cases of Good, 32 of Low, 74 of Poor, and 60 cases of Bad probability. Detailed model runs were made for all 14 High or Good probability cases, a total of only 7.8% of all analyzed. Based on the results of this study we have identified a few dates on which a release of a reasonable amount of PMCH tracer (on the order of 500 kg

  6. A preliminary study on numerical simulation of microwave heating process for chemical reaction and discussion of hotspot and thermal runaway phenomenon

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    The nonlinear process of microwave heating chemical reaction is studied by means of numerical simulation. Especially,the variation of temperature in terms of space and time,as well as the hotspot and thermal runaway phenomena are discussed. Suppose the heated object is a cylinder and the incident electromagnetic(EM) wave is plane wave,the problem turns out to be a coupling calculation of 2D multi-physical fields. The integral equation of EM field is solved using the method of moment(MoM) and the thermal conduction equation is solved using a semi-analysis method. Moreover,a method to determine the equivalent complex permittivity of reactant under the heating is presented in order to perform the calculation. The numerical results for water and a dummy chemical reaction(A) show that the hotspot is a ubiquitous phenomenon in microwave heating process. When the radius of the heated object is small,the highest temperature occurs somewhere inside the object due to the concentration of the EM wave. While the radius increases to a certain degree,the highest temperature occurs somewhere close to the surface due to the skin effect,and the whole high temperature area shows crescent-shaped. That is in accordance with basic physical principles. If the radius is kept the same in the heating process,the hotspot position of water does not change,while that of reaction A with several radius values varies. For either water or A,the thermal runaway phenomenon in which small difference of radius results in large difference of highest temperature,occurs easily when the radius is small. On the contrary,it is not evident when the radius is large. Moreover,it is notable that the highest temperature in water shows oscillating decreasing trend with the increase of radius,but in reaction A almost decreases monotonously. Further study should be performed to determine if this difference is only an occasional occurrence.

  7. Preliminary simulation of chloride transport in the Equus Beds aquifer and simulated effects of well pumping and artificial recharge on groundwater flow and chloride transport near the city of Wichita, Kansas, 1990 through 2008

    Science.gov (United States)

    Klager, Brian J.; Kelly, Brian P.; Ziegler, Andrew C.

    2014-01-01

    The Equus Beds aquifer in south-central Kansas is a primary water-supply source for the city of Wichita. Water-level declines because of groundwater pumping for municipal and irrigation needs as well as sporadic drought conditions have caused concern about the adequacy of the Equus Beds aquifer as a future water supply for Wichita. In March 2006, the city of Wichita began construction of the Equus Beds Aquifer Storage and Recovery project, a plan to artificially recharge the aquifer with excess water from the Little Arkansas River. Artificial recharge will raise groundwater levels, increase storage volume in the aquifer, and deter or slow down a plume of chloride brine approaching the Wichita well field from the Burrton, Kansas area caused by oil production activities in the 1930s. Another source of high chloride water to the aquifer is the Arkansas River. This study was prepared in cooperation with the city of Wichita as part of the Equus Beds Aquifer Storage and Recovery project. Chloride transport in the Equus Beds aquifer was simulated between the Arkansas and Little Arkansas Rivers near the Wichita well field. Chloride transport was simulated for the Equus Beds aquifer using SEAWAT, a computer program that combines the groundwater-flow model MODFLOW-2000 and the solute-transport model MT3DMS. The chloride-transport model was used to simulate the period from 1990 through 2008 and the effects of five well pumping scenarios and one artificial recharge scenario. The chloride distribution in the aquifer for the beginning of 1990 was interpolated from groundwater samples from around that time, and the chloride concentrations in rivers for the study period were interpolated from surface water samples. Five well-pumping scenarios and one artificial-recharge scenario were assessed for their effects on simulated chloride transport and water levels in and around the Wichita well field. The scenarios were: (1) existing 1990 through 2008 pumping conditions, to serve as a

  8. A PRELIMINARY JUPITER MODEL

    Energy Technology Data Exchange (ETDEWEB)

    Hubbard, W. B. [Lunar and Planetary Laboratory, The University of Arizona, Tucson, AZ 85721 (United States); Militzer, B. [Department of Earth and Planetary Science, Department of Astronomy, University of California, Berkeley, CA 94720 (United States)

    2016-03-20

    In anticipation of new observational results for Jupiter's axial moment of inertia and gravitational zonal harmonic coefficients from the forthcoming Juno orbiter, we present a number of preliminary Jupiter interior models. We combine results from ab initio computer simulations of hydrogen–helium mixtures, including immiscibility calculations, with a new nonperturbative calculation of Jupiter's zonal harmonic coefficients, to derive a self-consistent model for the planet's external gravity and moment of inertia. We assume helium rain modified the interior temperature and composition profiles. Our calculation predicts zonal harmonic values to which measurements can be compared. Although some models fit the observed (pre-Juno) second- and fourth-order zonal harmonics to within their error bars, our preferred reference model predicts a fourth-order zonal harmonic whose absolute value lies above the pre-Juno error bars. This model has a dense core of about 12 Earth masses and a hydrogen–helium-rich envelope with approximately three times solar metallicity.

  9. 数值模拟方法在地震预测研究中应用的初步探讨(Ⅱ)%PRELIMINARY STUDY ON APPLICATION OF NUMERICAL SIMULATION METHODS TO EARTHQUAKE PREDICTION RESEARCH(Ⅱ)

    Institute of Scientific and Technical Information of China (English)

    邓志辉; 胡勐乾; 周斌; 陆远忠; 陶京玲; 马晓静; 姜辉; 李红

    2011-01-01

    With the advances in simulation techniques and understanding of geodynamic processes, numerical simulation is likely to play an increasingly important role in the research of seismic hazard analysis and earthquake prediction. In this paper,on the basis of the paper "A preliminary study on the application of numerical simulation methods to earthquake prediction research ( I ) " , the possible application of uncoordinated deformation analysis, Coulomb stress changes and earthquake probability modeling to the study of earthquake prediction is further discussed.When rock deforms from the elastic into the yield stage, the system is in a critical unstable state, the rock movement may deviate from the normal track and become complicated. The study results show that,before Wenan earthquake( Ms 5. 1 ) on July 4,2006, GPS velocity was well consistent with the numerical simulation speed in most areas of North China, while there were some differences in some regions, especially in the northeast of the North China Plain block, where big inconsistency in movement characteristics occurred, resulting perhaps from the preparation of Wenan earthquake.Research on earthquakes triggered by Coulomb stress change is a focus problem now. Numerical simulation may play an important role in the analysis of Coulomb stress changes. By constructing three-dimensional dynamic model, the effect of various factors on the value and distribution of Coulomb stress change can be simulated, and more realistic results can be obtained. By numerical simulation of Coulomb stress changes to seismic activities beneath Sichuan Zipingpu reservoirs, it is found that with the increase of reservoir water storage time,the pore pressure diffusion in the effective additional stress field will be gradually expanded to the range of more than 10km underground. The regional effective additional stress field and seismic activities show different characteristics in several typical regions.The United States Southern

  10. Microstructural and Computer Simulation Studies on Some EFP Materials

    Science.gov (United States)

    Pappu, Sridhar

    1999-06-01

    Explosively Formed Penetrators (EFPs) are self-forming ballistic projectiles deriving their energy from the detonation of a high explosive. As they form in-flight, strains up to 3 are reached at strain rates of about 10^4 per second, resulting in extreme deformation related changes in microstructure. In this study, we report microstructural features of three different EFP materials in an effort to understand the underlying mechanism behind EFP formation. The materials studied are Cu, Fe and Ta and represent different crystal structures and widely differing melting temperatures, properties that seem to play a significant role in microstructural evolution during the EFP formation process. Computer simulations using AUTODYN 2D software program will be carried out and the generated temperature and stress contours will be correlated with the observed microstructural features and measured microhardness data along the EFP half-section. This would help validate the hydrocodes and give useful insight into the unobservable part of the EFP formation process. Such a correlation of experimental and mathematical models would not only help understand the mechanism behind this process but also help design more effective projectiles without carrying out expensive experimental tests.

  11. Hydrocode Simulation with Modified Johnson-Cook Model and Experimental Analysis of Explosively Formed Projectiles

    Science.gov (United States)

    Hussain, G.; Hameed, A.; Hetherington, J. G.; Barton, P. C.; Malik, A. Q.

    2013-04-01

    The formation of mild steel (MS) and copper (Cu) explosively formed projectiles (EFPs) was simulated in AUTODYN using both the Johnson-Cook (JC) and modified Johnson-Cook (JCM) constitutive models. The JC model was modified by increasing the hardening constant by 10%. The previously established semi-empirical equations for diameter, length, velocity, and depth of penetration were used to verify the design of the EFP. The length-to-diameter (L/D) ratio of the warhead used in the simulation varied between 1 projectile distortion or breakup for large standoff applications, the design of the EFP warhead was modified to obtain a lower L/D ratio. Simulations from the JC model underestimated the EFP diameter, resulting in an unrealistically elongated projectile. This shortcoming was resolved by employing the JCM model, giving good agreement with the experimental results. The projectile velocity and hole characteristics in 10-mm-thick aluminum target plates were studied for both models. The semi-empirical equations and the JC model overestimated the projectile velocity, whereas the JCM model underestimated the velocity slightly when compared to the experimental results. The depths of penetration calculated by the semi-empirical equations in the aluminum (Al) target plate were 55 and 52 mm for Cu and MS EFPs, respectively.

  12. 2016 TRI Preliminary Dataset

    Science.gov (United States)

    The TRI preliminary dataset includes the most current TRI data available and reflects toxic chemical releases and pollution prevention activities that occurred at TRI facilities during the 2016 calendar year.

  13. Simulation of changes in temperature and pressure fields during high speed projectiles forming by explosion

    Directory of Open Access Journals (Sweden)

    Marković Miloš D.

    2016-01-01

    Full Text Available The Research in this paper considered the temperatures fields as the consequently influenced effects appeared by plastic deformation, in the explosively forming process aimed to design Explosively Formed Projectiles (henceforth EFP. As the special payloads of the missiles, used projectiles are packaged as the metal liners, joined with explosive charges, to design explosive propulsion effect. Their final form and velocity during shaping depend on distributed temperatures in explosively driven plastic deformation process. Developed simulation model consider forming process without metal cover of explosive charge, in aim to discover liner’s dynamical correlations of effective plastic strains and temperatures in the unconstrained detonation environment made by payload construction. The temperature fields of the liner’s copper material are considered in time, as the consequence of strain/stress displacements driven by explosion environmental thermodynamically fields of pressures and temperatures. Achieved final velocities and mass loses as the expected EFP performances are estimated regarding their dynamical shaping and thermal gradients behavior vs. effective plastic strains. Performances and parameters are presented vs. process time, numerically simulated by the Autodyne software package. [Projekat Ministarstva nauke Republike Srbije, br. III-47029

  14. 结核分枝杆菌模拟抗原的筛选及初步应用%Simulation antigens screening from Mycobacterium tuberculosis and its preliminary clinical study

    Institute of Scientific and Technical Information of China (English)

    刘丽蓉; 乐军; 刘建芳; 韩敏; 杨景卉; 陈晋

    2012-01-01

    OBJECTIVE To establish a new clinical diagnosis method of Mycobacterium tuberculosis infection by ESAT-6and CFP-10 peptide library screening of M. Tuberculosis antigen simulation. METHODS A random peptide library was designed and synthesized based on the sequences of ESAT-6 and CFP-10 protein. M. Tuberculosis antigen-specific analog peplides were screened by y-interferon release tests, the working concentration was also determined. RESULTS Three specific analog peptides were obtained after several rounds of screening, including P1MG, P8NV, and P11LD, with the sensitivity of 93. 3%, 90. 0%,80. 0% respectively; all the specificity was greater than 90%. The concentration of the working concentration is 2 jug/ml. The three analog peptides worked as the original stimulus in detecting y-interferon release when they were mixed in the equal levels. The preliminary clinical validation study showed that the sensitivity was 95. 3%, and specificity was 96. 2%. CONCLUSION By using the mixed analog peptide antigen which were designed, selected, prepared based on protein ESAT-6 and CFP-10 sequence, it is expected to establish a new method of clinical diagnosis of M. Tuberculosis.%目的 通过对甲期分泌抗原-6(ESAT-6)及培养基滤过蛋白-10(CFP-10)肽库的结核分枝杆菌模拟抗原的筛选,旨在建立一个临床鉴别诊断结核分枝杆菌感染的新方法.方法 基于蛋白ESAT-6和CFP 10的序列,随机设计合成一组1 9肽库,通过γ-干扰素释放试验筛选特异性结核分枝杆菌抗原模拟多肽,并研究确立其工作浓度.结果 经过多轮筛选获得3条特异性模拟多肽,分别是P1MG、P8NV、P11LD,灵敏度分别为93.3%、90.0%、80.0%,特异性均>90.0%;工作浓度均为2 μg/ml;将3种模拟多肽等浓度混合作为刺激原,初步临床验证试验表明,其灵敏度为95.3%,特异性为96.2%.结论 基于蛋白ESAT-6和CFP-10的序列设计、筛选、制备的混合型模拟多肽抗原,有望建立一种

  15. UVISS preliminary visibility analysis

    DEFF Research Database (Denmark)

    Betto, Maurizio

    1998-01-01

    The goal of this work is to obtain a preliminary assessment of the sky visibility for anastronomical telescope located on the express pallet of the International SpaceStation (ISS)} taking into account the major constraints imposed on the instrument by the ISSattitude and structure. Part of the w......The goal of this work is to obtain a preliminary assessment of the sky visibility for anastronomical telescope located on the express pallet of the International SpaceStation (ISS)} taking into account the major constraints imposed on the instrument by the ISSattitude and structure. Part...

  16. UVISS preliminary visibility analysis

    DEFF Research Database (Denmark)

    Betto, Maurizio

    1998-01-01

    The goal of this work is to obtain a preliminary assessment of the sky visibility for anastronomical telescope located on the express pallet of the International SpaceStation (ISS)} taking into account the major constraints imposed on the instrument by the ISSattitude and structure. Part...

  17. Numerical simulation of armor capability of AI2O3 and SiC armor tiles

    Science.gov (United States)

    Rashid, T.; Aleem, M. A.; Akbar, S.; Rauf, A.; Shuaib, M.

    2016-08-01

    Alumina and Silicon Carbide armor plates have been tested numerically against 7.62x51 (mm x mm) armor piercing (AP) projectiles. A 2-D problem with axial symmetry has been designedand the simulations were carried out using commercial software ANSYS AUTODYN. Experiments were modeled for Alumina (99.5%), Alumina (99.7%) and SiC with a range of tile thicknesses (5, 10, 15 and 20 mm). The projectile was chosen as 7.62 x 51AP bullet (initial velocity 810 m/sec)with two different core materials Steel 4340 and WC, however, casing material was copper for both cores. SiC showed better defense against AP bullet as compared to Al2O3. The residual velocity and momentum of the bullet were found to decrease with increasing tile thickness. SiC tiles with thickness 15mm and 20 mm successfully sustained penetration against steel 4340 and WC core bullets, respectively. However none of the Alumina targets succeeded in stopping the bullet.

  18. Preliminary simulation of implants breast through the accelerated partial irradiation technique: coverage rates and homogeneity; Simulacion previa de implates de mama mediante la tecnica de irradiacion parcial acelerada: indices de cubrimiento y homegeneidad

    Energy Technology Data Exchange (ETDEWEB)

    Moral Sanchez, S. C.; Paula Carranza, B. de; Erzibengoa, M.; Bragado Alvarez, L.; Guisasola Berasetegui, A.

    2013-07-01

    In this work we present and evaluate the process of pre-simulation we have drawn up when it comes to treatments of accelerated partial irradiation of breast. Previous simulation that we will allow you to have greater control over the location of catheters with respect to the area to radiate. The goodness of this procedure is evaluated through representative quality indexes of the implant. (Author)

  19. On Preliminary Breakdown

    Science.gov (United States)

    Beasley, W. H.; Petersen, D.

    2013-12-01

    The preliminary breakdown phase of a negative cloud-to-ground lightning flash was observed in detail. Observations were made with a Photron SA1.1 high-speed video camera operating at 9,000 frames per second, fast optical sensors, a flat-plate electric field antenna covering the SLF to MF band, and VHF and UHF radio receivers with bandwidths of 20 MHz. Bright stepwise extensions of a negative leader were observed at an altitude of 8 km during the first few milliseconds of the flash, and were coincident with bipolar electric field pulses called 'characteristic pulses'. The 2-D step lengths of the preliminary processes were in excess of 100 meters, with some 2-D step lengths in excess of 200 meters. Smaller and shorter unipolar electric field pulses were superposed onto the bipolar electric field pulses, and were coincident with VHF and UHF radio pulses. After a few milliseconds, the emerging negative stepped leader system showed a marked decrease in luminosity, step length, and propagation velocity. Details of these events will be discussed, including the possibility that the preliminary breakdown phase consists not of a single developing lightning leader system, but of multiple smaller lightning leader systems that eventually join together into a single system.

  20. Stardust Interstellar Preliminary Examination (ISPE)

    Science.gov (United States)

    Westphal, A. J.; Allen, C.; Bajt, S.; Basset, R.; Bastien, R.; Bechtel, H.; Bleuet, P.; Borg, J.; Brenker F.; Bridges, J.

    2009-01-01

    In January 2006 the Stardust sample return capsule returned to Earth bearing the first solid samples from a primitive solar system body, C omet 81P/Wild2, and a collector dedicated to the capture and return o f contemporary interstellar dust. Both collectors were approximately 0.1m(exp 2) in area and were composed of aerogel tiles (85% of the co llecting area) and aluminum foils. The Stardust Interstellar Dust Col lector (SIDC) was exposed to the interstellar dust stream for a total exposure factor of 20 m(exp 2-) day during two periods before the co metary encounter. The Stardust Interstellar Preliminary Examination ( ISPE) is a three-year effort to characterize the collection using no ndestructive techniques. The ISPE consists of six interdependent proj ects: (1) Candidate identification through automated digital microsco py and a massively distributed, calibrated search (2) Candidate extr action and photodocumentation (3) Characterization of candidates thro ugh synchrotronbased FourierTranform Infrared Spectroscopy (FTIR), S canning XRay Fluoresence Microscopy (SXRF), and Scanning Transmission Xray Microscopy (STXM) (4) Search for and analysis of craters in f oils through FESEM scanning, Auger Spectroscopy and synchrotronbased Photoemission Electron Microscopy (PEEM) (5) Modeling of interstell ar dust transport in the solar system (6) Laboratory simulations of h ypervelocity dust impacts into the collecting media

  1. The friction of polymers around Tg,Tm : Preliminary results

    DEFF Research Database (Denmark)

    Sivebæk, Ion Marius; Samoilov, V N; Persson, B N J

    We present Molecular Dynamics calculations involving polymers of different lengths. Polymers with lengths from 20 to 1400 carbon atoms are considered. The systems are able to simulate friction between polymer surfaces and polymer against metal. The results we present are very preliminary...

  2. Environmental Survey preliminary report

    Energy Technology Data Exchange (ETDEWEB)

    1988-04-01

    This report presents the preliminary findings from the first phase of the Environmental Survey of the United States Department of Energy (DOE) Sandia National Laboratories conducted August 17 through September 4, 1987. The objective of the Survey is to identify environmental problems and areas of environmental risk associated with Sandia National Laboratories-Albuquerque (SNLA). The Survey covers all environmental media and all areas of environmental regulation. It is being performed in accordance with the DOE Environmental Survey Manual. This phase of the Survey involves the review of existing site environmental data, observations of the operations carried on at SNLA, and interviews with site personnel. 85 refs., 49 figs., 48 tabs.

  3. Ruiz Volcano: Preliminary report

    Science.gov (United States)

    Ruiz Volcano, Colombia (4.88°N, 75.32°W). All times are local (= GMT -5 hours).An explosive eruption on November 13, 1985, melted ice and snow in the summit area, generating lahars that flowed tens of kilometers down flank river valleys, killing more than 20,000 people. This is history's fourth largest single-eruption death toll, behind only Tambora in 1815 (92,000), Krakatau in 1883 (36,000), and Mount Pelée in May 1902 (28,000). The following briefly summarizes the very preliminary and inevitably conflicting information that had been received by press time.

  4. 基于计算机书法创作的形象思维模拟初步探索%Preliminary Exploration of Imagery Thinking Simulation Based on Creation of Computer Calligraphy

    Institute of Scientific and Technical Information of China (English)

    薛环振; 颜卫

    2011-01-01

    思维模拟主要是以控制论和信息论为理论基础,使用计算机从功能、行为上来模拟和代替人的某些特定智能.无论是在人工智能领域,还是在思维科学领域,形象思维和抽象思维都具有同样重要作用.但是,迄今为止智能的机器模拟还局限于抽象(逻辑)思维领域,对形象思维的认识才刚刚开始.介绍了通过计算机书法创作进行形象思维模拟的探索和尝试,目的是讨论以计算机书法创作进行思维模拟的可行性.结果表明,计算机书法创作是思维模拟的有效切人点.%Thinking simulation is mainly based on control theory and information theory,which simulates and replaces some specific human intelligences from functions and behaviors by means of computers.No matter in artificial intelligence or in thinking science,imagery thinking and abstract thinking are equally important.But so far,the research on artificial intelligence is still limited in abstract thinking and too few research results of imagery thing are generated.The paper introduces the exploration and triumph on imagery thinking simulation by the creation process of computer calligraphy so as to find the feasibility of the simulation.The result shows that the creation process of computer calligraphy is an efficient pointcut of thinking simulation.

  5. Simulation of synchrotron motion with rf noise

    Energy Technology Data Exchange (ETDEWEB)

    Leemann, B.T.; Forest, E.; Chattopadhyay, S.

    1986-08-01

    The theoretical formulation is described that is behind an algorithm for synchrotron phase-space tracking with rf noise and some preliminary simulation results of bunch diffusion under rf noise obtained by actual tracking.

  6. Nuclear subsurface explosion modeling and hydrodynamic fragmentation simulation of hazardous asteroids

    Science.gov (United States)

    Premaratne, Pavithra Dhanuka

    Disruption and fragmentation of an asteroid using nuclear explosive devices (NEDs) is a highly complex yet a practical solution to mitigating the impact threat of asteroids with short warning time. A Hypervelocity Asteroid Intercept Vehicle (HAIV) concept, developed at the Asteroid Deflection Research Center (ADRC), consists of a primary vehicle that acts as kinetic impactor and a secondary vehicle that houses NEDs. The kinetic impactor (lead vehicle) strikes the asteroid creating a crater. The secondary vehicle will immediately enter the crater and detonate its nuclear payload creating a blast wave powerful enough to fragment the asteroid. The nuclear subsurface explosion modeling and hydrodynamic simulation has been a challenging research goal that paves the way an array of mission critical information. A mesh-free hydrodynamic simulation method, Smoothed Particle Hydrodynamics (SPH) was utilized to obtain both qualitative and quantitative solutions for explosion efficiency. Commercial fluid dynamics packages such as AUTODYN along with the in-house GPU accelerated SPH algorithms were used to validate and optimize high-energy explosion dynamics for a variety of test cases. Energy coupling from the NED to the target body was also examined to determine the effectiveness of nuclear subsurface explosions. Success of a disruption mission also depends on the survivability of the nuclear payload when the secondary vehicle approaches the newly formed crater at a velocity of 10 km/s or higher. The vehicle may come into contact with debris ejecting the crater which required the conceptual development of a Whipple shield. As the vehicle closes on the crater, its skin may also experience extreme temperatures due to heat radiated from the crater bottom. In order to address this thermal problem, a simple metallic thermal shield design was implemented utilizing a radiative heat transfer algorithm and nodal solutions obtained from hydrodynamic simulations.

  7. Surface integral formulation of Maxwell's equations for simulation of non-destructive testing by eddy currents. Preliminary study on the implementation of the fast multipole method; Formulation integrale surfacique des equations de Maxwell pour la simulation de controles non destructifs par courant de Foucault. Etude preliminaire a la mise en oeuvre de la methode multipole rapide.

    Energy Technology Data Exchange (ETDEWEB)

    Lim, T.

    2011-04-28

    To simulate numerically a non-destructive by eddy current testing (NDT-CF), the sensor response can be modeled through a semi-analytical approach by volume integral equations. Faster than the finite element method, this approach is however restricted to the study of plane or cylindrical parts (without taking into account the edge effects) because of the complexity of the expression of the dyadic Green function for more general configurations. However, there is an industrial demand to extend the capabilities of the CF model in complex configurations (deformed plates, edges effects...). We were thus brought to formulate the electromagnetic problem differently, by setting ourselves the goal of maintaining a semi-analytical approach. The surface integral equation (SIE) expresses the volume problem by an equivalent transmission one at the interfaces (2D) between homogeneous sub-domains. This problem is approached by a linear system (by the method of moments), whose number of unknowns is reduced due to the nature of the surfacic mesh. Therefore, this system can be solved by a direct solver for small configurations. That enabled us to treat several various positions of the sensor for only one inversion of the impedance matrix. The numerical results obtained using this formulation involve plates with consideration of edge effects such as edge and corner. They are consistent with results obtained by the finite element method. For larger configurations, we conducted a preliminary study for the adaptation of an acceleration method of the matrix vector product involved in an iterative solver (fast multipole method or FMM) to define the conditions under which the FMM calculation works correctly (accuracy, convergence...) in the NDT's domain. A special attention has been given to the choice of basis functions (which have to satisfy an Hdiv conforming property) and on the evaluation of near interactions (which are weakly singular). (author) [French] Pour simuler

  8. A Preliminary Study on the Scene Simulation Method in Emergency Triage Teaching of Higher Vocational Nursing Students%情景模拟法在高职护生急诊分诊教学中的初步研究

    Institute of Scientific and Technical Information of China (English)

    刘丽

    2015-01-01

    Objective:To understand the situation and analyze the existing problems in the application of scene simulation method in emergency triage teaching of higher vocational nursing students, and to find out the countermeasures to improve the teaching effect.Method:The issuance of a self-made questionnaire was used,the effect of the scene simulation teaching of 240 vocational nursing students in our hospital were investigated.Result:Over 90% of nursing students thought that the application of scene simulation method stimulated the students' learning interest, improved the critical thinking ability of nursing students, and cultivated the ability of communication and team spirit. In the factor investigation of the effect of scene simulation, 79.17% of nursing students considered that the content of scene simulation was not enough; 87.50% of nursing students considered that the teaching case was too typical;69.58% of nursing students considered that teachers were not made in a timely manner.Conclusion: Through the application of scene simulation in emergency triage teaching, change the traditional way of teaching and cultivate the nursing students learning ability,it has good teaching effects.%目的:了解情景模拟法在高职护生急诊分诊教学中的应用现状,分析其存在问题,找出提高情景模拟教学效果的对策。方法:通过发放自制问卷,对本院240名高职护生进行情景模拟教学的作用、效果和可能影响因素的调查。结果:90%以上的护生认为情景模拟法应用在急诊分诊教学中能够激发护生的学习兴趣,提高护生的评判性思维能力,同时可以培养护生的沟通能力和团队精神。影响情景模拟法在急诊分诊的教学效果的因素调查中,79.17%的护生认为是情景模拟的内容对护生的吸引力不够;87.50%的护生认为情景模拟中的教学病例太典型;69.58%的护生认为教师没有作出及时评价等。结论:通过将情

  9. Thermal energy storage in aquifiers: preliminary information

    Energy Technology Data Exchange (ETDEWEB)

    Allen, R.D.

    1979-12-01

    Topics discussed include: conceptual designs; numerical modelling; field experiments; relevant technical information; feasibility studies; preliminary aquifer selection considerations; and preliminary design and operating considerations. (TFD)

  10. Calculus of spatial distribution of absorbed dose to cellular level by Monte Carlo simulation for a radio-labelled peptide with {sup 188}Re and with nuclear internalization : preliminary results; Calculo de la distribucion espacial de dosis absorbida a nivel celular por simulacion Monte Carlo para un peptido radiomarcado con {sup 188}Re y con internalizacion nuclear : resultados preliminares

    Energy Technology Data Exchange (ETDEWEB)

    Rojas C, E. L. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); Santos C, C. L. [Universidad Autonoma del Estado de Mexico, Paseo Tollocan y Jesus Carranza, Toluca 50120, Estado de Mexico (Mexico)], e-mail: leticia.rojas@inin.gob.mx

    2009-10-15

    The {sup 188}Re is a radionuclide of radiation gamma emitter, useful in obtaining of gamma-graphic images, but it is also emitter of beta radiations and Auger electrons. A bio-molecule directed to a specific receptor of a cancer cell labeled with a emitter radionuclide of beta particles and Auger electrons, as the {sup 188}Re-Tat-Bombesin, it has the potential to be used in radiotherapy of molecular targets for its capacity to penetrate to cellular nucleus. In this system, the radiation dose is distributed in way located at microscopic levels in sub cellular specific places, where Auger emissions contributes of significant way in absorbed dose. The cellular dosimetry is realized in most of cases, using analytic or semi analytical methods, for example the cellular MIRD methodology. However, it is required to complement these calculations simulating the electrons transport and considering experimental bio kinetics data. Therefore, in this work preliminary results are presented of dosimetric calculation to sub cellular level for {sup 188}Re-Tat-Bombesin by Monte Carlo simulation, using the 2008 version of PENELOPE: PENEASY code. The spatial distribution of absorbed dose in membrane, cytoplasm and nucleus, was calculated with geometry of a cell of 10 {mu}m of diameter, a nucleus of 2 {mu}m of ratio and membrane of 0.2 {mu}m of thickness, considering elementary constitution for each cellular compartment proposal in literature. The total number of disintegrations at sub cellular level was evaluated integrating the activity in function of time starting from experimental bio kinetics data in mamma cancer cells MDA-MB231. The preliminary results show that 46.4% of total disintegrations for unit of captured activity by cell occurs in nucleus, 38.4% in membrane and 15.2% in cytoplasm. The due absorbed dose to Auger electrons for 1 Bq of {sup 188}Re located in cellular membrane were respectively of 1.32E-1 and 1.43E-1 Gy in cytoplasm and nucleus. (Author)

  11. The Preliminaries of a Reference

    DEFF Research Database (Denmark)

    Butler, Graham; Sadl, Urska

    2017-01-01

    by the reasons why the Court after an oral hearing held in the presence of the parties and eight intervening Member States, and after hearing the Advocate General did not deliver one. The comment examines the legal framework, as well as the detailed procedural rules and guidelines that govern the cooperation...... of national courts in the preliminary reference procedure. It highlights the fact that preliminary references can only work when the preliminaries of a reference – the culture of sincere cooperation and litigation, efficient communication and flexible procedural rules – are in place....

  12. Preliminary reference Earth model

    Science.gov (United States)

    Dziewonski, Adam M.; Anderson, Don L.

    1981-06-01

    A large data set consisting of about 1000 normal mode periods, 500 summary travel time observations, 100 normal mode Q values, mass and moment of inertia have been inverted to obtain the radial distribution of elastic properties, Q values and density in the Earth's interior. The data set was supplemented with a special study of 12 years of ISC phase data which yielded an additional 1.75 × 10 6 travel time observations for P and S waves. In order to obtain satisfactory agreement with the entire data set we were required to take into account anelastic dispersion. The introduction of transverse isotropy into the outer 220 km of the mantle was required in order to satisfy the shorter period fundamental toroidal and spheroidal modes. This anisotropy also improved the fit of the larger data set. The horizontal and vertical velocities in the upper mantle differ by 2-4%, both for P and S waves. The mantle below 220 km is not required to be anisotropic. Mantle Rayleigh waves are surprisingly sensitive to compressional velocity in the upper mantle. High S n velocities, low P n velocities and a pronounced low-velocity zone are features of most global inversion models that are suppressed when anisotropy is allowed for in the inversion. The Preliminary Reference Earth Model, PREM, and auxiliary tables showing fits to the data are presented.

  13. Deployment of a Pressure Sensitive Paint System for Measuring Global Surface Pressures on Rotorcraft Blades in Simulated Forward Flight: Preliminary PSP Results from Test 581 in the 14- by 22-Foot Subsonic Tunnel

    Science.gov (United States)

    Watkins, Anthony Neal; Leighty, Bradley D.; Lipford, William E.; Wong, Oliver D.; Goodman, Kyle Z.; Crafton, James; Forlines, Alan; Goss, Larry; Gregory, James W.; Juliano, Thomas J.

    2011-01-01

    This report will present details of a Pressure Sensitive Paint (PSP) system for measuring global surface pressures on the tips of rotorcraft blades in simulated forward flight at the 14- x 22-Foot Subsonic Tunnel. The system was designed to use a pulsed laser as an excitation source and PSP data was collected using the lifetime-based approach. With the higher intensity of the laser, this allowed PSP images to be acquired during a single laser pulse, resulting in the collection of crisp images that can be used to determine blade pressure at a specific instant in time. This is extremely important in rotorcraft applications as the blades experience dramatically different flow fields depending on their position in the rotor disk. Testing of the system was performed using the U.S. Army General Rotor Model System equipped with four identical blades. Two of the blades were instrumented with pressure transducers to allow for comparison of the results obtained from the PSP. This report will also detail possible improvements to the system.

  14. Arapahoe NWR diversion reconstruction : Preliminary

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This is a preliminary plan for a diversion reconstruction for Hubbard #2. Oklahoma #1, Dryer, Hill and Crowder sites on the Arapahoe National Wildlife Refuge.

  15. 公共汽车内TNT炸药爆炸的有限元模拟%Finite element simulation of TNT explosion in the bus

    Institute of Scientific and Technical Information of China (English)

    王立军; 孙树德

    2012-01-01

    Considering the enormous size difference between the TNT and the Bus, the paper established the finite element model of TNT explosion in the bus with the AUTODYN REMAP technology,and solved the problems of calculation both of accuracy and time of the finite element model,and the pressure distribution and the process curve of pressure and velocity in typical position were obtained. Simulation results provide the theory basis to determine the extent of injury and bus damage degree.%考虑到TNT炸药与公共汽车在尺寸上的巨大差异,应用有限元程序AUTODYN提供的REMAP映射技术,建立公共汽车内TNT炸药爆炸的有限元模型,解决汽车有限元模型计算精度和计算时间问题,获得炸药爆炸后车内压力分布云图及典型位置的压力和速度历程曲线.仿真结果为确定人员伤害及汽车损伤程度提供了理论基础.

  16. 梓木蒸汽爆破过程传热数值模拟初探%A preliminary study on numerical simulation of heat-transfer mechanism during Catalpa ovata wood steam explosion process

    Institute of Scientific and Technical Information of China (English)

    郝晓峰; 刘文金; 李贤军; 吕建雄; 孙德林; 陈新义

    2014-01-01

    Numerical simulation of heat transfer mechanism during Catalpa ovata wood steam explosion pretreatment was studied by taking into account the effects of internal moisture, moist air and solid wood frame materials on heat transfer. One-dimensional heat transfer mathematical model was established based on Fourier law, the numerical calculation program for this model was compiled based on Finite Difference Scheme and Formula Translator Fortran, and the accuracy of this model was validated by the experiments. The results show that, this model can more accurately reflect the Catalpa ovate wood steam explosion process, and quantitively analyze the variation of temperature and pressure with time in tested wood.%针对梓木蒸汽爆破过程中传热机理的数值模拟进行研究。考虑木材内部水分、湿空气与固相骨架物质的对传热的影响,基于傅里叶导热定律,建立一维梓木爆破过程中传热数学模型,利用有限差分数学思想结合Fortran语言编写该模型数值计算程序,并通过实验验证了模型的准确性。结果表明该模型可以较为准确的反应梓木蒸汽爆破过程中的加热过程,能够定量分析板材内的温度、压力随时间变化的规律。

  17. A preliminary characterization of the spatial variability of precipitation at Yucca Mountain, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    Hevesi, J.A.; Flint, A.L. [Geological Survey, Mercury, NV (United States); Ambos, D.S. [Foothill Engineering Consultants, Mercury, NV (United States)

    1994-12-31

    Isohyetal maps of precipitation and numerical models for simulating precipitation are needed to characterize natural infiltration at Yucca Mountain, Nevada. The objective of this study was to characterize the spatial variability of precipitation within the domain of the natural catchments overlying the potential repository, and to define preliminary geostatistical models based on differences in storm type for the numerical simulation of precipitation.

  18. HL-2M偏滤器的综合模拟技术初步研究%Preliminary investigation on the integrated simulation of the HL-2M divertor

    Institute of Scientific and Technical Information of China (English)

    才来中; 崔学武; 刘健; 薛雷; 丁锐

    2016-01-01

    The integrated simulation of the divertor is implemented. Many issues including the optimization of the divertor configuration, physical process of detachment, gas puffing and pumping, and vertical displacement event (VDE) on HL-2M are investigated by applying the SOLPS and DINA codes. The effects of divertor plates geometry and detachment on the deposited heat load of divertor plates are evaluated. And the impacts of the gas puffing position, the gas puffing rate and the pumping rate on the divertor performance are also discussed. In addition, the VDEs on HL-2M are also predicted by the DINA code, and the variation of plasma current profile during the VDEs is given, thus the input for the design and analysis of the HL-2M divertor is provided.%利用SOLPS和DINA程序,对偏滤器的数值模拟进行综合研究。结合HL-2M装置,针对偏滤器的结构优化、脱靶物理过程、偏滤器送气与抽气、垂直位移事件(VDE)等问题进行了模拟研究。分析了偏滤器靶板位形以及脱靶对偏滤器靶板热载荷的影响,研究了偏滤器的送气位置、送气速率、抽气速率等因素对于偏滤器性能的影响;同时,利用DINA程序对HL-2M装置的VDE过程进行了预测分析,并给出了HL-2M装置发生VDE过程的等离子体电流剖面变化,从而为HL-2M装置的偏滤器结构设计和分析提供输入数据。

  19. CBCT与Simplant软件口腔种植模拟的初步研究%Preliminary Study of CBCT and Simplant Software in the Simulated Surgery of Dental Implant

    Institute of Scientific and Technical Information of China (English)

    林梓桐; 王铁梅; 刘澍; 童昕; 王芳芳

    2013-01-01

    Objective: To study the Cone beam computed tomography(CBCT) and Simplant software in simulated surgery of dental implant. Methods: 5 mandibular cases were used the CBCT scanning, the buccolingual width at the alveolar crest(H1) , the distance from the alveolar crest to the superior edge of the mandibular nerve canal (H2) and buccolingual location for mandibular nerve canal was evaluated. Simplant software was used to stimulate the implant process, including the oral implant, abutment, restorative, forces and bone mineral density. Results: Five implant cases of mandibular posterior teeth were studied: H1 was between 9. 9 -12. 0mm, and H2 was between 8. 8 -15. 5mm, the mandibular nerve canal was more lingual at the molar region than the premolar region. Conclusion: CBCT was accurate for three-dimensional preoperative assessment, and combined with the third-party software Simplant the implant process was more easy and controllable.%目的:探讨锥形束CT(Cone beam computed tomography,CBCT)运用于口腔种植的成像要点及第三方软件Simplant软件的手术模拟功能的实现方式.方法:对经临床筛选的5例下颌后牙种植患者使用CBCT成像,测量种植区牙槽嵴颊舌向牙槽嵴宽度(H1)、牙槽嵴顶至下颌神经管上壁的高度(H2),并对种植部位下颌神经管颊舌向位置进行评估.使用Simplant软件对口腔种植的种植体、基台、种植修复体、种植体承受的侧向应力、种植体周围骨密度进行模拟计算.结果:5例后牙种植患者,H1在9.9~12.0 mm之间,H2在8.8~15.5mm之间,下颌神经管由后向前走行,越近磨牙后方越靠近舌侧.5例患者均参照手术模拟的结果行种植手术,术后6个月随访无种植体失败.结论:CBCT对种植区可进行精确的三维术前评估,结合第三方软件Simplant的手术模拟功能可使种植过程更加简便可控.

  20. Preliminary Studies on Pulsed Electric Field Breakdown of Lead Azide

    Science.gov (United States)

    1976-10-01

    1/2 OS CO ton NO. S3L TECHNICAL REPORT 4991 PRELIMINARY SUJDfES ON PULSED ELECTRIC FIELD BREAKDOWN OF LEAD AZIDE L AVRAMI M. BUMS D. DOWNS...Introduction Background A. Contact Effects B. Pulsed Electric Field Measurements Experimental A. Contact Effects B. Pulsed Electric Fields Discussion...B. Pulsed Electric Field Measurements The application of pulsed electric fields to lead azide does not exactly simulate the conditions experienced

  1. Numerical simulation of the fluid-structure interaction between air blast waves and soil structure

    Science.gov (United States)

    Umar, S.; Risby, M. S.; Albert, A. Luthfi; Norazman, M.; Ariffin, I.; Alias, Y. Muhamad

    2014-03-01

    Normally, an explosion threat on free field especially from high explosives is very dangerous due to the ground shocks generated that have high impulsive load. Nowadays, explosion threats do not only occur in the battlefield, but also in industries and urban areas. In industries such as oil and gas, explosion threats may occur on logistic transportation, maintenance, production, and distribution pipeline that are located underground to supply crude oil. Therefore, the appropriate blast resistances are a priority requirement that can be obtained through an assessment on the structural response, material strength and impact pattern of material due to ground shock. A highly impulsive load from ground shocks is a dynamic load due to its loading time which is faster than ground response time. Of late, almost all blast studies consider and analyze the ground shock in the fluid-structure interaction (FSI) because of its influence on the propagation and interaction of ground shock. Furthermore, analysis in the FSI integrates action of ground shock and reaction of ground on calculations of velocity, pressure and force. Therefore, this integration of the FSI has the capability to deliver the ground shock analysis on simulation to be closer to experimental investigation results. In this study, the FSI was implemented on AUTODYN computer code by using Euler-Godunov and the arbitrary Lagrangian-Eulerian (ALE). Euler-Godunov has the capability to deliver a structural computation on a 3D analysis, while ALE delivers an arbitrary calculation that is appropriate for a FSI analysis. In addition, ALE scheme delivers fine approach on little deformation analysis with an arbitrary motion, while the Euler-Godunov scheme delivers fine approach on a large deformation analysis. An integrated scheme based on Euler-Godunov and the arbitrary Lagrangian-Eulerian allows us to analyze the blast propagation waves and structural interaction simultaneously.

  2. Preliminary Evaluation of Altitude Scaling for Turbofan Engine Ice Crystal Icing

    Science.gov (United States)

    Tsao, Jen-Ching

    2017-01-01

    Preliminary evaluation of altitude scaling for turbofan engine ice crystal icing simulation was conducted during the 2015 LF11 engine icing test campaign in PSL.The results showed that a simplified approach for altitude scaling to simulate the key reference engine ice growth feature and associated icing effects to the engine is possible. But special considerations are needed to address the facility operation limitation for lower altitude engine icing simulation.

  3. Preliminary exploration on the training of medical students' humanity and communication skills through situation simulation and behavior correction%情境模拟和行为纠正教学在医学本科生人文实践技能培训中的探索

    Institute of Scientific and Technical Information of China (English)

    徐蓓莉; 黄一沁; 张艳; 向阳; 陈华; 蔡依蕴; 邵云潮; 费国强; 赖雁妮

    2015-01-01

    The course "Doctoring" is designed mainly to deal with the practice of medical communication skills and clinical situation by the view of humanity and professionalism.Undergraduates in the early learning phase were taught with advanced communication skills on the basis of Calgary-Cambridge guidelines by using standard patient based simulation and behavior correction.Teachers using methods like class teaching, group discussion, simulating diagnosis and treatment, self and mutual comments and final summary to give doctoring lessons which emphasize on students' equal opportunities to practice.Questionnaires were used to evaluate teaching effect.Most of the students learned empathy, the structure of the interrogation, the preliminary master communication skills, self-confidence to communicate with patients.All the students think that this course can help medical work in the future, so it is necessary to set up this course.Teachers also gave positive feedback.%"从医之道"课程以Calgary-Cambridge指南为基础,采用基于标准化病人的情境训练和行为纠正教学法,从培养医学生职业素养和人文实践技能的角度,对医学沟通技能和临床情境的应对处理的教授进行了教学改革.课堂采用大班授课、分组讨论、模拟诊疗、师生互评、标准化病人点评、教师总结的教学形式,强调给予每位学生实战学习的机会.通过问卷调查评价教学效果,学生及教师的问卷均给出了积极的反馈信息.全体医学生的医患沟通能力均有不同程度的提高,大部分学生学会了共情、问诊结构,初步掌握了沟通技巧,与患者交流的自信心增加.全部学生都认为,本课程有助于今后医疗工作的开展,有必要设立本门课程.教师也在授课过程中与学生共同进步.

  4. THE EFFECTS OF PRELIMINARY RULINGS

    Directory of Open Access Journals (Sweden)

    Iuliana-Mădălina LARION

    2015-07-01

    Full Text Available The study analyses the effects of the preliminary rulings rendered by the Court of Justice for the judicial body that made the reference and for other bodies dealing with similar cases, for the member states, for the European Union’ s institutions and for EU legal order. Starting from the binding effect of the preliminary judgment for national judicial bodies, which requires them to follow the ruling or make a new reference, to the lack of precedent doctrine in EU law, continuing with the possibility to indirectly verify the compatibility of national law of the member states with EU law and ending with the administrative or legislative measures that can or must be taken by the member states, the study intends to highlight the limits, nuances and consequences of the binding effect. It mentions the contribution of the national courts and of the Court of Justice of the European Union to the development of EU law, such as clarifying autonomous notions and it emphasizes the preliminary procedure's attributes of being a form of judicial protection of individual rights, as well as a means to review the legality of acts of EU institutions. The paper is meant to be a useful instrument for practitioners. Therefor, it also deals with the possibility and limits of asking new questions, in order to obtain reconsideration or a refinement of the legal issue and with the problem of judicial control over the interpretation and application of the preliminary ruling by the lower court.

  5. A Preliminary Study of Heat Strain Using Modelling and Simulation

    Science.gov (United States)

    2006-05-01

    pour inclure le travail effectué dans des conditions climatiques extrêmes, notamment à des températures d’environ 45 oC (WBGT), et que les durées de... changement de la température centrale et la désydratation en sont les principales causes. Cette étude a traité des conditions environnementales (résumées

  6. preliminary multidomain modelling and simulation study of a ...

    African Journals Online (AJOL)

    user

    Renewable energy sources have gained much attention due to the recent energy crisis and ... system for the most energy capture for this case study to be a rotor speed of 5.5rad/s at a height of 10m. .... Thesis, Faculty of California Polytechnic.

  7. Simulating motivated cognition

    Science.gov (United States)

    Gevarter, William B.

    1991-01-01

    A research effort to develop a sophisticated computer model of human behavior is described. A computer framework of motivated cognition was developed. Motivated cognition focuses on the motivations or affects that provide the context and drive in human cognition and decision making. A conceptual architecture of the human decision-making approach from the perspective of information processing in the human brain is developed in diagrammatic form. A preliminary version of such a diagram is presented. This architecture is then used as a vehicle for successfully constructing a computer program simulation Dweck and Leggett's findings that relate how an individual's implicit theories orient them toward particular goals, with resultant cognitions, affects, and behavior.

  8. Virtual Collaborative Simulation Environment for Integrated Product and Process Development

    Science.gov (United States)

    Gulli, Michael A.

    1997-01-01

    Deneb Robotics is a leader in the development of commercially available, leading edge three- dimensional simulation software tools for virtual prototyping,, simulation-based design, manufacturing process simulation, and factory floor simulation and training applications. Deneb has developed and commercially released a preliminary Virtual Collaborative Engineering (VCE) capability for Integrated Product and Process Development (IPPD). This capability allows distributed, real-time visualization and evaluation of design concepts, manufacturing processes, and total factory and enterprises in one seamless simulation environment.

  9. 45 CFR 150.217 - Preliminary determination.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 1 2010-10-01 2010-10-01 false Preliminary determination. 150.217 Section 150.217... Are Failing To Substantially Enforce HIPAA Requirements § 150.217 Preliminary determination. If, at... designees). (b) Notifies the State of CMS's preliminary determination that the State has failed to...

  10. Reconsideration of the simulated work task situation

    DEFF Research Database (Denmark)

    Borlund, Pia; Schneider, Jesper Wiborg

    2010-01-01

    The present paper reports on the initial study and the preliminary findings of how the concept of simulated work task situation is reported used in the research literature. The overall objective of the study is in a systematic manner to learn how and for what types of evaluations the concept...... is applied. In particular we are interested to learn whether the recommendations for how to apply simulated work task situations are followed. The preliminary findings indicate a need for clarifications of the recommendations of how to use simulated work task situations. Particularly with respect to ‘realism......’ of the simulated work task situations, which is emphasised through the need for tailoring of the simulated work task situations towards the group of study participant to ensure the depicted situations are realistic and interesting from the participants’ point of view. Likewise it seems that the recommendation...

  11. Preliminaries

    Directory of Open Access Journals (Sweden)

    Desde el jardín de Freud

    2014-10-01

    Full Text Available Desde el Jardín de Freud se encuentra indexada en el IBN-Publindex (Colciencias, en categoría C, y en Latindex. También se encuentra en las siguientes bases de datos y catálogos: ebsco, Dialnet, Rebiun, Doaj y e-Revistas.

  12. Preliminary Report on Coining of Targets

    Energy Technology Data Exchange (ETDEWEB)

    Davis, P; Wall, M; Hodge, N; Schwartz, A

    2004-07-27

    We were tasked with developing a coining technique that would evaluate the feasibility of using a pressing, or coining process to imprint a one-dimensional sinusoidal pattern onto a thin disk specimen. We performed finite element method simulations of the coining process, designed, built, and tested a coining apparatus and tested surrogate materials, and coined a sample of special nuclear material. The preliminary results were encouraging. The pressing of a 3-mm diameter by {approx}100 {micro}m thick disc to 500 pounds of pressure produced a flat part with a 1-{micro}m deep by 50-{micro}m period sine wave pattern covering all of the surface and thus demonstrated the method for replicating ultraprecision, mesoscale features onto a near-net-shape metallic blank. This coining technique is being developed to provide specialty processing for the manufacturing of difficult to machine, millimeter-size components made from materials that present hazardous conditions. The technology is versatile and can be used to imprint a wide range of features, or profiles into two opposing surfaces. The coining process requires a simple, conceivably hand held tool, which efficiently produces ultra-precision work pieces without the production of byproducts such as machining chips, or grinding swarf. It shows promise for use on ductile materials that cannot be precision machined with conventional single crystal diamond tooling. As a production process, it can be used to reduce manufacturing costs where large numbers of ultra-precision, repetitive designs are required.

  13. Preliminary ECLSS waste water model

    Science.gov (United States)

    Carter, Donald L.; Holder, Donald W., Jr.; Alexander, Kevin; Shaw, R. G.; Hayase, John K.

    1991-01-01

    A preliminary waste water model for input to the Space Station Freedom (SSF) Environmental Control and Life Support System (ECLSS) Water Processor (WP) has been generated for design purposes. Data have been compiled from various ECLSS tests and flight sample analyses. A discussion of the characterization of the waste streams comprising the model is presented, along with a discussion of the waste water model and the rationale for the inclusion of contaminants in their respective concentrations. The major objective is to establish a methodology for the development of a waste water model and to present the current state of that model.

  14. Preliminary ECLSS waste water model

    Science.gov (United States)

    Carter, Donald L.; Holder, Donald W., Jr.; Alexander, Kevin; Shaw, R. G.; Hayase, John K.

    1991-01-01

    A preliminary waste water model for input to the Space Station Freedom (SSF) Environmental Control and Life Support System (ECLSS) Water Processor (WP) has been generated for design purposes. Data have been compiled from various ECLSS tests and flight sample analyses. A discussion of the characterization of the waste streams comprising the model is presented, along with a discussion of the waste water model and the rationale for the inclusion of contaminants in their respective concentrations. The major objective is to establish a methodology for the development of a waste water model and to present the current state of that model.

  15. Preliminary considerations concerning actinide solubilities

    Energy Technology Data Exchange (ETDEWEB)

    Newton, T.W.; Bayhurst, B.P.; Daniels, W.R.; Erdal, B.R.; Ogard, A.E.

    1980-01-01

    Work at the Los Alamos Scientific Laboratory on the fundamental solution chemistry of the actinides has thus far been confined to preliminary considerations of the problems involved in developing an understanding of the precipitation and dissolution behavior of actinide compounds under environmental conditions. Attempts have been made to calculate solubility as a function of Eh and pH using the appropriate thermodynamic data; results have been presented in terms of contour maps showing lines of constant solubility as a function of Eh and pH. Possible methods of control of the redox potential of rock-groundwater systems by the use of Eh buffers (redox couples) is presented.

  16. Reconsideration of the simulated work task situation

    DEFF Research Database (Denmark)

    Borlund, Pia; Schneider, Jesper Wiborg

    2010-01-01

    The present paper reports on the initial study and the preliminary findings of how the concept of simulated work task situation is reported used in the research literature. The overall objective of the study is in a systematic manner to learn how and for what types of evaluations the concept is a...

  17. International linear collider simulations using BDSIM

    Indian Academy of Sciences (India)

    J Carter; I Agapov; G A Blair; O Dadoun

    2007-12-01

    Power loss simulations for the 2, 14, and 20 mrad extraction line designs using the BDSIM toolkit are presented. A preliminary study on the backgrounds from the beam losses along the extraction line in the case of 20 mrad with high luminosity parameters is also given.

  18. Utility of Social Modeling for Proliferation Assessment - Preliminary Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Coles, Garill A.; Gastelum, Zoe N.; Brothers, Alan J.; Thompson, Sandra E.

    2009-06-01

    This Preliminary Assessment draft report will present the results of a literature search and preliminary assessment of the body of research, analysis methods, models and data deemed to be relevant to the Utility of Social Modeling for Proliferation Assessment research. This report will provide: 1) a description of the problem space and the kinds of information pertinent to the problem space, 2) a discussion of key relevant or representative literature, 3) a discussion of models and modeling approaches judged to be potentially useful to the research, and 4) the next steps of this research that will be pursued based on this preliminary assessment. This draft report represents a technical deliverable for the NA-22 Simulations, Algorithms, and Modeling (SAM) program. Specifically this draft report is the Task 1 deliverable for project PL09-UtilSocial-PD06, Utility of Social Modeling for Proliferation Assessment. This project investigates non-traditional use of social and cultural information to improve nuclear proliferation assessment, including nonproliferation assessment, proliferation resistance assessments, safeguards assessments and other related studies. These assessments often use and create technical information about the State’s posture towards proliferation, the vulnerability of a nuclear energy system to an undesired event, and the effectiveness of safeguards. This project will find and fuse social and technical information by explicitly considering the role of cultural, social and behavioral factors relevant to proliferation. The aim of this research is to describe and demonstrate if and how social science modeling has utility in proliferation assessment.

  19. Preliminary Phase Field Computational Model Development

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yulan [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hu, Shenyang Y. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Xu, Ke [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Suter, Jonathan D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); McCloy, John S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Johnson, Bradley R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Ramuhalli, Pradeep [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2014-12-15

    experiments, special experimental methods were devised to create similar boundary conditions in the iron films. Preliminary MFM studies conducted on single and polycrystalline iron films with small sub-areas created with focused ion beam have correlated quite well qualitatively with phase-field simulations. However, phase-field model dimensions are still small relative to experiments thus far. We are in the process of increasing the size of the models and decreasing specimen size so both have identical dimensions. Ongoing research is focused on validation of the phase-field model. Validation is being accomplished through comparison with experimentally obtained MFM images (in progress), and planned measurements of major hysteresis loops and first order reversal curves. Extrapolation of simulation sizes to represent a more stochastic bulk-like system will require sampling of various simulations (i.e., with single non-magnetic defect, single magnetic defect, single grain boundary, single dislocation, etc.) with distributions of input parameters. These outputs can then be compared to laboratory magnetic measurements and ultimately to simulate magnetic Barkhausen noise signals.

  20. Preliminary Investigation of a Paraglider

    Science.gov (United States)

    Rogallo, Francis M.; Lowry, John G.; Croom, Delwin R.; Taylor, Robert T.

    1960-01-01

    A preliminary investigation of the aerodynamic and control characteristics of a flexible glider similar to a parachute in construction has been made at the Langley Research Center to evaluate its capabilities as a reentry glider. Preliminary weight estimates of the proposed vehicle indicate that such a structure can be made with extremely low wing loading. Maximum temperatures during the reentry maneuver might be held as low as about 1,500 F. The results of wind-tunnel and free-glide tests show that the glider when constructed of nonporous material performed extremely well at subsonic speeds and could be flown at angles of attack from about 200 to 900. At supersonic speeds the wing showed none of the unfavorable tendencies exhibited by conventional parachutes at these speeds, such as squidding and breathing. Several methods of packing and deploying the glider have been successfully demonstrated. The results of this study indicate that this flexible-lifting-surface concept may provide a lightweight controllable paraglider for manned space vehicles.

  1. Topaz II preliminary safety assessment

    Science.gov (United States)

    Marshall, Albert C.; Standley, Vaughn; Voss, Susan S.; Haskin, Eric

    1993-01-01

    The Strategic Defense Initiative Organization (SDIO) decided to investigate the possibility of launching a Russian Topaz II space nuclear power system. A preliminary safety assessment was conducted to determine whether or not a space mission could be conducted safely and within budget constraints. As part of this assessment, a safety policy and safety functional requirements were developed to guide both the safety assessment and future Topaz II activities. A review of the Russian flight safety program was conducted and documented. Our preliminary safety assessment included a top level event tree, neutronic analysis of normal and accident configurations, an evaluation of temperature coefficients of reactivity, a reentry and disposal analysis, and analysis of postulated launch abort impact accidents, and an analysis of postulated propellant fire and explosion accidents. Based on the assessment, it appears that it will be possible to safely launch the Topaz II system in the U.S. with some possible system modifications. The principal system modifications will probably include design changes to preclude water flooded criticality and to assure intact reentry.

  2. Simulations applied to the bright SHARC XCLF Results and implications

    CERN Document Server

    Ulmer, M P; Pildis, R A; Romer, A K; Nichol, R C; Holden, B P

    1999-01-01

    We have performed simulations of the effectiveness of the Serendipitous High-redshift Archival ROSAT Cluster (SHARC) survey for various model universes. We find, in agreement with work based on a preliminary set of simulations no statistically significant evolution of the luminosity function out to z = 0.8.

  3. 23 CFR 645.109 - Preliminary engineering.

    Science.gov (United States)

    2010-04-01

    ... 23 Highways 1 2010-04-01 2010-04-01 false Preliminary engineering. 645.109 Section 645.109 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS UTILITIES Utility Relocations, Adjustments, and Reimbursement § 645.109 Preliminary engineering. (a) As...

  4. 33 CFR 116.10 - Preliminary review.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Preliminary review. 116.10... ALTERATION OF UNREASONABLY OBSTRUCTIVE BRIDGES § 116.10 Preliminary review. (a) Upon receipt of a written complaint, the District Commander will review the complaint to determine if, in the District...

  5. Plutonium Immobilization Can Loading Preliminary Specifications

    Energy Technology Data Exchange (ETDEWEB)

    Kriikku, E.

    1998-11-25

    This report discusses the Plutonium Immobilization can loading preliminary equipment specifications and includes a process block diagram, process description, equipment list, preliminary equipment specifications, plan and elevation sketches, and some commercial catalogs. This report identifies loading pucks into cans and backfilling cans with helium as the top priority can loading development areas.

  6. 18 CFR 1b.6 - Preliminary investigations.

    Science.gov (United States)

    2010-04-01

    ... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Preliminary investigations. 1b.6 Section 1b.6 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF ENERGY GENERAL RULES RULES RELATING TO INVESTIGATIONS § 1b.6 Preliminary investigations....

  7. KALIMER preliminary conceptual design report

    Energy Technology Data Exchange (ETDEWEB)

    Hahn, Do Hee; Kim, Y. J.; Kim, Y. G. and others

    2000-08-01

    This report, which summarizes the result of preliminary conceptual design activities during Phase 1, follows the format of safety analysis report. The purpose of publishing this report is to gather all of the design information developed so far in a systematic way so that KALIMER designers have a common source of the consistent design information necessary for their future design activities. This report will be revised and updated as design changes occur and more detailed design specification is developed during Phase 2. Chapter 1 describes the KALIMER Project. Chapter 2 includes the top level design requirements of KALIMER and general plant description. Chapter 3 summarizes the design of structures, components, equipment and systems. Specific systems and safety analysis results are described in the remaining chapters. Appendix on the HCDA evaluation is attached at the end of this report.

  8. Simulating Evolution

    Science.gov (United States)

    Stebbins, Robert C.; Allen, Brockenbrough

    1975-01-01

    Described are simulations that can be used to illustrate evolution by natural selection. Suggestions for simulating phenomena such as adaptive radiation, color match to background and vision of predators are offered. (BR)

  9. Preliminary hazards analysis -- vitrification process

    Energy Technology Data Exchange (ETDEWEB)

    Coordes, D.; Ruggieri, M.; Russell, J.; TenBrook, W.; Yimbo, P. [Science Applications International Corp., Pleasanton, CA (United States)

    1994-06-01

    This paper presents a Preliminary Hazards Analysis (PHA) for mixed waste vitrification by joule heating. The purpose of performing a PHA is to establish an initial hazard categorization for a DOE nuclear facility and to identify those processes and structures which may have an impact on or be important to safety. The PHA is typically performed during and provides input to project conceptual design. The PHA is then followed by a Preliminary Safety Analysis Report (PSAR) performed during Title 1 and 2 design. The PSAR then leads to performance of the Final Safety Analysis Report performed during the facility`s construction and testing. It should be completed before routine operation of the facility commences. This PHA addresses the first four chapters of the safety analysis process, in accordance with the requirements of DOE Safety Guidelines in SG 830.110. The hazards associated with vitrification processes are evaluated using standard safety analysis methods which include: identification of credible potential hazardous energy sources; identification of preventative features of the facility or system; identification of mitigative features; and analyses of credible hazards. Maximal facility inventories of radioactive and hazardous materials are postulated to evaluate worst case accident consequences. These inventories were based on DOE-STD-1027-92 guidance and the surrogate waste streams defined by Mayberry, et al. Radiological assessments indicate that a facility, depending on the radioactive material inventory, may be an exempt, Category 3, or Category 2 facility. The calculated impacts would result in no significant impact to offsite personnel or the environment. Hazardous materials assessment indicates that a Mixed Waste Vitrification facility will be a Low Hazard facility having minimal impacts to offsite personnel and the environment.

  10. Simulating Vito

    CERN Document Server

    Fragapane, Alexander

    2013-01-01

    This paper discusses the techniques used to simulate the proposed upgrade to the ASPIC line at ISOLDE, VITO. It discusses the process used in the program SIMION by explaining how to start with an Autodesk Inventor drawing and import this into SIMION to get a working simulation. It then goes on to discuss the pieces of VITO which have been simulated in the program and how they were simulated. Finally, it explains a little about the simulations of the full beamline which have been done and discusses what still needs to be done.

  11. A preliminary investigation of the use of throttles for emergency flight control

    Science.gov (United States)

    Burcham, F. W., Jr.; Fullerton, C. Gordon; Gilyard, Glenn B.; Wolf, Thomas D.; Stewart, James F.

    1991-01-01

    A preliminary investigation was conducted regarding the use of throttles for emergency flight control of a multiengine aircraft. Several airplanes including a light twin-engine piston-powered airplane, jet transports, and a high performance fighter were studied during flight and piloted simulations. Simulation studies used the B-720, B-727, MD-11, and F-15 aircraft. Flight studies used the Lear 24, Piper PA-30, and F-15 airplanes. Based on simulator and flight results, all the airplanes exhibited some control capability with throttles. With piloted simulators, landings using manual throttles-only control were extremely difficult. An augmented control system was developed that converts conventional pilot stick inputs into appropriate throttle commands. With the augmented system, the B-720 and F-15 simulations were evaluated and could be landed successfully. Flight and simulation data were compared for the F-15 airplane.

  12. AN-107 (C) Simulant Bench-Scale LAW Evaporation with Organic Regulatory Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Saito, H.H.

    2001-05-15

    The overall objective of this work is to develop preliminary operating data including expected concentration endpoints using a C waste envelope simulant. The data is to be used for the preliminary Hanford RPP flow sheet development and LAW Melter Feed Evaporator design.

  13. Births: preliminary data for 2012.

    Science.gov (United States)

    Hamilton, Brady E; Martin, Joyce A; Ventura, Stephanie J

    2013-09-01

    Objectives-This report presents preliminary data for 2012 on births in the United States. U.S. data on births are shown by age, live-birth order, race, and Hispanic origin of mother. Data on marital status, cesarean delivery, preterm births, and low birthweight are also presented. Methods-Data in this report are based on 99.96% of 2012 births.Records for the few states with less than 100% of records received are weighted to independent control counts of all births received in state vital statistics offices in 2012. Comparisons are made with final 2011 data. Results-The preliminary number of births for the United States in 2012 was 3,952,937, essentially unchanged (not statistically significant) from 2011; the general fertility rate was 63.0 births per 1,000 women aged 15-44, down only slightly from 2011, after declining nearly 3% a year from 2007 through 2010. The number of births and fertility rate either declined or were unchanged for most race and Hispanic origin groups from 2011 to 2012; however, both the number of births and the fertility rate for Asian or Pacific Islander women rose in 2012 (7% and 4%, respectively). The birth rate for teenagers aged 15-19 was down 6% in 2012 (29.4 births per 1,000 teenagers aged 15-19), yet another historic low for the United States, with rates declining for younger and older teenagers and for nearly all race and Hispanic origin groups. The birth rate for women in their early 20s also declined in 2012, to a new record low of 83.1 births per 1,000 women. Birth rates for women in their 30s rose in 2012, as did the birth rate for women in their early 40s. The birth rate for women in their late 40s was unchanged. The nonmarital birth rate declined in 2012 (to 45.3 birth per 1,000 unmarried women aged 15-44), whereas the number of births to unmarried women rose 1% and the percentage of births to unmarried women was unchanged (at 40.7%). The cesarean delivery rate for the United States was unchanged in 2012 at 32.8%. The preterm

  14. Bayesian Treaty Monitoring: Preliminary Report

    Science.gov (United States)

    2011-09-01

    differencing ( BDD ), because it resembles the method of double-differencing both in the sense of correcting for velocity heterogeneity and in its...Figure 8. (a) Simulated 2-D event clusters located using BDD (+) along with their true locations (x). Stations are positioned at the four

  15. Human Factors Topics in Flight Simulation: An Annotated Bibliography

    Science.gov (United States)

    1976-01-01

    preliminary analysis). NTDC 20-RM-I -1 M, September 1958. TRAINING. RUOCCO, J.N., VITALE, P.A. and BENFARI, R.C. Kinetic cueing in simulated carrier...treatment of simulation along general lines. Use is made in this connection of the linearised control theory. Some typical examples of fixed-base, kinetic and...revision in a cinematic method of simulating low altitude flight. Cockpit instruments were synchronised with a motion picture scene. The throttle

  16. Preliminary Iron Distribution on Vesta

    Science.gov (United States)

    Mittlefehldt, David W.; Mittlefehldt, David W.

    2013-01-01

    The distribution of iron on the surface of the asteroid Vesta was investigated using Dawn's Gamma Ray and Neutron Detector (GRaND) [1,2]. Iron varies predictably with rock type for the howardite, eucrite, and diogenite (HED) meteorites, thought to be representative of Vesta. The abundance of Fe in howardites ranges from about 12 to 15 wt.%. Basaltic eucrites have the highest abundance, whereas, lower crustal and upper mantle materials (cumulate eucrites and diogenites) have the lowest, and howardites are intermediate [3]. We have completed a mapping study of 7.6 MeV gamma rays produced by neutron capture by Fe as measured by the bismuth germanate (BGO) detector of GRaND [1]. The procedures to determine Fe counting rates are presented in detail here, along with a preliminary distribution map, constituting the necessary initial step to quantification of Fe abundances. We find that the global distribution of Fe counting rates is generally consistent with independent mineralogical and compositional inferences obtained by other instruments on Dawn such as measurements of pyroxene absorption bands by the Visual and Infrared Spectrometer (VIR) [4] and Framing Camera (FC) [5] and neutron absorption measurements by GRaND [6].

  17. EUPORIAS: plans and preliminary results

    Science.gov (United States)

    Buontempo, C.

    2013-12-01

    Recent advances in our understanding and ability to forecast climate variability have meant that skilful predictions are beginning to be routinely made on seasonal to decadal (s2d) timescales. Such forecasts have the potential to be of great value to a wide range of decision-making, where outcomes are strongly influenced by variations in the climate. In 2012 the European Commission funded EUPORIAS, a four year long project to develop prototype end-to-end climate impact prediction services operating on a seasonal to decadal timescale, and assess their value in informing decision-making. EUPORIAS commenced on 1 November 2012, coordinated by the UK Met Office leading a consortium of 24 organisations representing world-class European climate research and climate service centres, expertise in impacts assessments and seasonal predictions, two United Nations agencies, specialists in new media, and commercial companies in climate-vulnerable sectors such as energy, water and tourism. The poster describes the setup of the project, its main outcome and some of the very preliminary results.

  18. Preliminary results of ANAIS-25

    CERN Document Server

    Amaré, J; Cuesta, C; García, E; Ginestra, C; Martínez, M; Oliván, M A; Ortigoza, Y; de Solórzano, A Ortiz; Pobes, C; Puimedón, J; Sarsa, M L; Villar, P; Villar, J A

    2013-01-01

    The ANAIS (Annual Modulation with NaI(Tl) Scintillators) experiment aims at the confirmation of the DAMA/LIBRA signal using the same target and technique at the Canfranc Underground Laboratory. 250 kg of ultrapure NaI(Tl) crystals will be used as a target, divided into 20 modules, each coupled to two photomultipliers. Two NaI(Tl) crystals of 12.5 kg each, grown by Alpha Spectra from a powder having a potassium level under the limit of our analytical techniques, form the ANAIS-25 set-up. The background contributions are being carefully studied and preliminary results are presented: their natural potassium content in the bulk has been quantified, as well as the uranium and thorium radioactive chains presence in the bulk through the discrimination of the corresponding alpha events by PSA, and due to the fast commissioning, the contribution from cosmogenic activated isotopes is clearly identified and their decay observed along the first months of data taking. Following the procedures established with ANAIS-0 and ...

  19. Simulation games

    OpenAIRE

    Giddings, S.

    2013-01-01

    This chapter outlines the conventions and pleasures of simulation games as a category, and explores the complicated and contested term simulation. This concept goes to the heart of what computer games and video games are, and the ways in which they articulate ideas, processes, and phenomena between their virtual worlds and the actual world. It has been argued that simulations generate and communicate knowledge and events quite differently from the long-­dominant cultural mode of narrative. Th...

  20. Process/Engineering Co-Simulation of Oxy-Combustion and Chemical Looping Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Sloan, David [Alstom Power Inc., Windsor, CT (United States)

    2013-03-01

    Over the past several years, the DOE has sponsored various funded programs, collectively referred to as Advanced Process Engineering Co-Simulator (APECS) programs, which have targeted the development of a steady-state simulator for advanced power plants. The simulator allows the DOE and its contractors to systematically evaluate various power plant concepts, either for preliminary conceptual design or detailed final design.

  1. Preliminary investigation into the possible endocrine disrupting ...

    African Journals Online (AJOL)

    JTEkanem

    In this study, we quantified the effect of Bonny- light crude oil contaminated diet ... This preliminary result suggest that Bonny-Light crude oil may have the potential .... different components. Its exploration ... organisms found in crude oil polluted.

  2. 42 CFR 457.925 - Preliminary investigation.

    Science.gov (United States)

    2010-10-01

    ... (CONTINUED) STATE CHILDREN'S HEALTH INSURANCE PROGRAMS (SCHIPs) ALLOTMENTS AND GRANTS TO STATES Program Integrity § 457.925 Preliminary investigation. If the State agency receives a complaint of fraud or abuse...

  3. Preliminary design data package. Appendix C

    Energy Technology Data Exchange (ETDEWEB)

    1979-07-25

    The design requirements, design philosophy, method and assumptions, and preliminary computer-aided design of the Near-Term Hybrid Vehicle including its electric and heat power units, control equipment, transmission system, body, and overall vehicle characteristics are presented. (LCL)

  4. Preliminary project proposal : Missouri chutes, NE & IA

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This proposal is for the Missouri Chutes National Wildlife Refuge that would be in Nebraska and Iowa on the Missouri River. This preliminary project proposal focuses...

  5. Preliminary Survey of Ectoparasites Infesting Chickens (Gallus ...

    African Journals Online (AJOL)

    Preliminary Survey of Ectoparasites Infesting Chickens (Gallus domesticus) in. Four Areas of ... were identified with the following prevalences: the shaft louse, Menopon gallinae (8.1%), the chicken ..... Canis lupus familiaris in Mueang district ...

  6. Renewable Energy Park - Preliminary Feasibility & Engineering Report

    Energy Technology Data Exchange (ETDEWEB)

    Ariwite, Roderick [Fallon Paiute Shoshone Tribe, NV (United States)

    2015-07-31

    This "Renewable Energy Park - Preliminary Feasibility & Engineering Report" seeks to provide an overall assessment and review of renewable energy development opportunities on the Fallon Indian Reservation and Colony Lands.

  7. Preliminary Determination of Epicenters (PDE) Bulletin

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — The NEIC global earthquake bulletin is called the Preliminary Determination of Epicenters or PDE, and is one of many discrete products in the ANSS Comprehensive...

  8. Alaska gold rush trails study: Preliminary draft

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Preliminary study draft, with maps, of seven gold rush trails in Alaska, to determine suitability for inclusion in the National Scenic Trails system and their...

  9. Preliminary organizational culture scale focused on artifacts.

    Science.gov (United States)

    Bonavia, Tomas

    2006-12-01

    In this preliminary study, an Organizational Culture Scale was developed to assess cultural artifacts according to Schein's typology (1985). It includes a set of cultural artifacts to measure the extent to which an organization is more or less traditional. A total of 249 managers from a range of different companies responded to the items. Preliminary analysis yielded a one-dimensional scale with 14 items with high internal consistency and homogeneity.

  10. Preliminary organizational culture scale focused on artifacts

    OpenAIRE

    Bonavia, Tomas

    2006-01-01

    In this preliminary study, an organizational culture scale was developed to assess cultural artifacts according to Schein´s typology (1985). It includes a set of cultural artifacts to measure the extent to which an organization is more or less traditional. A total of 249 managers from a range of different companies responded to the items. Preliminary analysis yielded a one-dimensional scale with 14 items with high internal consistency and homogeneity.

  11. Excel simulations

    CERN Document Server

    Verschuuren, Gerard M

    2013-01-01

    Covering a variety of Excel simulations, from gambling to genetics, this introduction is for people interested in modeling future events, without the cost of an expensive textbook. The simulations covered offer a fun alternative to the usual Excel topics and include situations such as roulette, password cracking, sex determination, population growth, and traffic patterns, among many others.

  12. Simulation tools

    CERN Document Server

    Jenni, F

    2006-01-01

    In the last two decades, simulation tools made a significant contribution to the great progress in development of power electronics. Time to market was shortened and development costs were reduced drastically. Falling costs, as well as improved speed and precision, opened new fields of application. Today, continuous and switched circuits can be mixed. A comfortable number of powerful simulation tools is available. The users have to choose the best suitable for their application. Here a simple rule applies: The best available simulation tool is the tool the user is already used to (provided, it can solve the task). Abilities, speed, user friendliness and other features are continuously being improved—even though they are already powerful and comfortable. This paper aims at giving the reader an insight into the simulation of power electronics. Starting with a short description of the fundamentals of a simulation tool as well as properties of tools, several tools are presented. Starting with simplified models ...

  13. Motion Simulator

    Science.gov (United States)

    1993-01-01

    MOOG, Inc. supplies hydraulic actuators for the Space Shuttle. When MOOG learned NASA was interested in electric actuators for possible future use, the company designed them with assistance from Marshall Space Flight Center. They also decided to pursue the system's commercial potential. This led to partnership with InterActive Simulation, Inc. for production of cabin flight simulators for museums, expositions, etc. The resulting products, the Magic Motion Simulator 30 Series, are the first electric powered simulators. Movements are computer-guided, including free fall to heighten the sense of moving through space. A projection system provides visual effects, and the 11 speakers of a digital laser based sound system add to the realism. The electric actuators are easier to install, have lower operating costs, noise, heat and staff requirements. The U.S. Space & Rocket Center and several other organizations have purchased the simulators.

  14. Ocean Thermal Energy Conversion power system development. Phase I: preliminary design. Final report. [ODSP-3 code; OTEC Steady-State Analysis Program

    Energy Technology Data Exchange (ETDEWEB)

    1978-12-04

    The following appendices are included; Dynamic Simulation Program (ODSP-3); sample results of dynamic simulation; trip report - NH/sub 3/ safety precautions/accident records; trip report - US Coast Guard Headquarters; OTEC power system development, preliminary design test program report; medium turbine generator inspection point program; net energy analysis; bus bar cost of electricity; OTEC technical specifications; and engineer drawings. (WHK)

  15. Preliminary design of the ITER ECH Upper Launcher

    Energy Technology Data Exchange (ETDEWEB)

    Strauss, D., E-mail: dirk.strauss@kit.edu [Karlsruhe Institute of Technology, Assoc. KIT-EURATOM, D-76021 Karlsruhe (Germany); Aiello, G. [Karlsruhe Institute of Technology, Assoc. KIT-EURATOM, D-76021 Karlsruhe (Germany); Chavan, R. [Centre de Recherches en Physique des Plasmas, CRPP–EPFL, CH-1015 Lausanne (Switzerland); Cirant, S. [Istituto di Fisica del Plasma CNR, Euratom Association, 20125 Milano (Italy); Baar, M. de [FOM, Van Vollenhovenlaan 659, 3527 JP, Utrecht (Netherlands); Farina, D. [Istituto di Fisica del Plasma CNR, Euratom Association, 20125 Milano (Italy); Gantenbein, G. [Karlsruhe Institute of Technology, Assoc. KIT-EURATOM, D-76021 Karlsruhe (Germany); Goodman, T.P. [Centre de Recherches en Physique des Plasmas, CRPP–EPFL, CH-1015 Lausanne (Switzerland); Henderson, M.A. [ITER Organization, 13108 Saint-Paul-lez-Durance (France); Kasparek, W. [Institut für Plasmaforschung, IPF, D-70569 Stuttgart (Germany); Kleefeldt, K. [Karlsruhe Institute of Technology, Assoc. KIT-EURATOM, D-76021 Karlsruhe (Germany); Landis, J.-D. [Centre de Recherches en Physique des Plasmas, CRPP–EPFL, CH-1015 Lausanne (Switzerland); Meier, A. [Karlsruhe Institute of Technology, Assoc. KIT-EURATOM, D-76021 Karlsruhe (Germany); Moro, A.; Platania, P. [Istituto di Fisica del Plasma CNR, Euratom Association, 20125 Milano (Italy); Plaum, B. [Institut für Plasmaforschung, IPF, D-70569 Stuttgart (Germany); Poli, E. [Max-Planck-IPP, Euratom Association, D-85748 Garching (Germany); Ramponi, G. [Istituto di Fisica del Plasma CNR, Euratom Association, 20125 Milano (Italy); Ronden, D. [FOM, Van Vollenhovenlaan 659, 3527 JP, Utrecht (Netherlands); Saibene, G. [Fusion for Energy, Barcelona (Spain); and others

    2013-11-15

    Highlights: • Front steering mirror design. • Plasma facing blanket shield module/first wall panel design. • Fixed frequency torus CVD diamond window serving as first tritium barrier. • Prototypes and tests of the above key components in the Launcher Handling and Testing Facility. -- Abstract: The design of the ITER electron cyclotron launchers recently reached the preliminary design level - the last major milestone before design finalization. The ITER ECH system contains 24 installed gyrotrons providing a maximum ECH injected power of 20 MW through transmission lines towards the tokamak. There are two EC launcher types both using a front steering mirror; one equatorial launcher (EL) for plasma heating and four upper launchers (UL) for plasma mode stabilization (neoclassical tearing modes and the sawtooth instability). A wide steering angle range of the ULs allows focusing of the beam on magnetic islands which are expected on the rational magnetic flux surfaces q = 1 (sawtooth instability), q = 3/2 and q = 2 (NTMs). In this paper the preliminary design of the ITER ECH UL is presented, including the optical system and the structural components. Highlights of the design include the torus CVD-diamond windows, the frictionless, front steering mechanism and the plasma facing blanket shield module (BSM). Numerical simulations as well as prototype tests are used to verify the design.

  16. Preliminary Economics for Hydrocarbon Fuel Production from Cellulosic Sugars

    Energy Technology Data Exchange (ETDEWEB)

    Collett, James R.; Meyer, Pimphan A.; Jones, Susanne B.

    2014-05-18

    Biorefinery process and economic models built in CHEMCAD and a preliminary, genome-scale metabolic model for the oleaginous yeast Lipomyces starkeyi were used to simulate the bioconversion of corn stover to lipids, and the upgrading of these hydrocarbon precursors to diesel and jet fuel. The metabolic model was based on the recently released genome sequence for L. starkeyi and on metabolic pathway information from the literature. The process model was based on bioconversion, lipid extraction, and lipid oil upgrading data found in literature, on new laboratory experimental data, and on yield predictions from the preliminary L. starkeyi metabolic model. The current plant gate production cost for a distillate-range hydrocarbon fuel was estimated by the process model Base Case to be $9.5/gallon ($9.0 /gallon of gasoline equivalent) with assumptions of 2011$, 10% internal return on investment, and 2205 ton/day dry feed rate. Opportunities for reducing the cost to below $5.0/gallon, such as improving bioconversion lipid yield and hydrogenation catalyst selectivity, are presented in a Target Case. The process and economic models developed for this work will be updated in 2014 with new experimental data and predictions from a refined metabolic network model for L. starkeyi. Attaining a production cost of $3.0/gallon will require finding higher value uses for lignin other than power generation, such as conversion to additional fuel or to a co-product.

  17. Solar Simulator

    Science.gov (United States)

    1981-01-01

    Oriel Corporation's simulators have a high pressure xenon lamp whose reflected light is processed by an optical system to produce a uniform solar beam. Because of many different types of applications, the simulators must be adjustable to replicate many different areas of the solar radiation spectrum. Simulators are laboratory tools for such purposes as testing and calibrating solar cells, or other solar energy systems, testing dyes, paints and pigments, pharmaceuticals and cosmetic preparations, plant and animal studies, food and agriculture studies and oceanographic research.

  18. A preliminary design of the collinear dielectric wakefield accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Zholents, A.; Gai, W.; Doran, S.; Lindberg, R.; Power, J.G.; Strelnikov, N.; Sun, Y.; Trakhtenberg, E.; Vasserman, I. [ANL, Argonne, IL 60439 (United States); Jing, C.; Kanareykin, A.; Li, Y. [Euclid Techlabs LLC, Solon, OH 44139 (United States); Gao, Q. [Tsinghua University, Beijing (China); Shchegolkov, D.Y.; Simakov, E.I. [LANL, Los Alamos, NM 87545 (United States)

    2016-09-01

    A preliminary design of the multi-meter long collinear dielectric wakefield accelerator that achieves a highly efficient transfer of the drive bunch energy to the wakefields and to the witness bunch is considered. It is made from ~0.5 m long accelerator modules containing a vacuum chamber with dielectric-lined walls, a quadrupole wiggler, an rf coupler, and BPM assembly. The single bunch breakup instability is a major limiting factor for accelerator efficiency, and the BNS damping is applied to obtain the stable multi-meter long propagation of a drive bunch. Numerical simulations using a 6D particle tracking computer code are performed and tolerances to various errors are defined.

  19. Design and preliminary test results of Daya Bay RPC modules*

    Energy Technology Data Exchange (ETDEWEB)

    Hackenburg, R.

    2011-09-01

    Resistive Plate Chamber (RPC) modules will be used as one part of the cosmic muon veto system in the Daya Bay reactor neutrino experiment. A total of 189 RPC modules will cover the three water pools in the experiment. To achieve track reconstruction and high efficiency, each module consists of 4 layers, each of which contains two sizes of bare chambers. The placement of bare chambers is reversed in different layers to reduce the overlapping dead areas. The module efficiency and patch efficiency were studied both in simulation and test of the data analysis. 143 modules have been constructed and tested. The preliminary study shows that the module and patch 3 out of 4 layers efficiency reaches about 98%.

  20. Design and preliminary test results of Daya Bay RPC modules

    Institute of Scientific and Technical Information of China (English)

    XU Ji-Lei; Logan Lebanowski; Cullen Newsom; Lin Shih-Kai; Jonathan Link; MA Lie-Hua; Viktor Pě(c); Vit Vorobel; CHEN Jin; LIU Jin-Chang; ZHOU Yong-Zhao; GUAN Meng-Yun; LIANG Hao; YANG Chang-Gen; WANG Yi-Fang; ZHANG Jia-Wen; LU Chang-Guo; Kirk McDonald; Robert Hackenburg; Kwong Lau

    2011-01-01

    Resistive Plate Chamber(RPC)modules will be used as one part of the cosmic muon veto system in the Days Bay reactor neutrino experiment.A total of 189 RPC modules will cover the three water pools in the experiment.To achieve track reconstruction and high efficiency,each module consists of 4 layers,each of which contains two sizes of bare chambers.The placement of bare chambers is reversed in different layers to reduce the overlapping dead areas.The module efficiency and patch efficiency were studied both in simulation and test of the data analysis.143 modules have been constructed and tested.The preliminary study shows that the module and patch 3 out of 4 layers efficiency reaches about 98%.

  1. Modeling the connection between development and evolution: Preliminary report

    Energy Technology Data Exchange (ETDEWEB)

    Mjolsness, E.; Reinitz, J. [Yale Univ., New Haven, CT (United States); Garrett, C.D. [Washington Univ., Seattle, WA (United States). Dept. of Computer Science; Sharp, D.H. [Los Alamos National Lab., NM (United States)

    1993-07-29

    In this paper we outline a model which incorporates development processes into an evolutionary frame work. The model consists of three sectors describing development, genetics, and the selective environment. The formulation of models governing each sector uses dynamical grammars to describe processes in which state variables evolve in a quantitative fashion, and the number and type of participating biological entities can change. This program has previously been elaborated for development. Its extension to the other sectors of the model is discussed here and forms the basis for further approximations. A specific implementation of these ideas is described for an idealized model of the evolution of a multicellular organism. While this model doe not describe an actual biological system, it illustrates the interplay of development and evolution. Preliminary results of numerical simulations of this idealized model are presented.

  2. Wide-angle cherenkov telescope prototype preliminary data

    Science.gov (United States)

    Timofeev, Lev; Anatoly, Ivanov

    2016-07-01

    This report presents an observation method of Cherenkov light from extensive air showers (EAS) generated by cosmic rays (CRs) above 10^16eV and preliminary observations. The interest in Cherenkov light differential detectors of EAS is caused by the possibility to measure the depth of cascade maximum, Xmax, and/or the shower age via angular and temporal distributions of the Cherenkov signal. In particular, it was shown using EAS model simulations that the pulse width measured at the periphery of the shower, r > 300 m, at sea level is pronouncedly connected with Xmax. Cherenkov detector is a wide-angle telescope working in coincidence with scintillation detectors, integral and differential Cherenkov detectors Yakutsk complex EAS.

  3. Preliminary background prediction for the INTEGRAL x-ray monitor

    DEFF Research Database (Denmark)

    Feroci, M.; Costa, E.; Budtz-Joergensen, C.

    1996-01-01

    The JEM-X (joint European x-ray monitor) experiment will be flown onboard the ESA's INTEGRAL satellite. The instrumental background level of the two JEM-X twin detectors will depend on several parameters, among which the satellite orbit and mass distribution, and the detectors materials play...... rays with the spacecraft structures. This calculation has been carried out by means of a Monte Carlo simulation using the code MCNP. The background due to on- orbit material activation and to the primary cosmic rays direct interactions with the detecting medium has not been considered. The INTEGRAL...... satellite structure is only now being completely defined and the details of the instrument design are still under evolution. The present background estimation can therefore be only preliminary and based on some reasonable approximations on the radiation environment in which the INTEGRAL experiments...

  4. Monte Carlo comparison of preliminary methods for ordering multiple genetic loci.

    OpenAIRE

    Olson, J.M.; Boehnke, M

    1990-01-01

    We carried out a simulation study to compare the power of eight methods for preliminary ordering of multiple genetic loci. Using linkage groups of six loci and a simple pedigree structure, we considered the effects on method performance of locus informativity, interlocus spacing, total distance along the chromosome, and sample size. Method performance was assessed using the mean rank of the true order, the proportion of replicates in which the true order was the best order, and the number of ...

  5. Preliminary design of an energy storing orthosis for providing gait to people with spinal cord injury.

    Science.gov (United States)

    Boughner, Kyle J; Durfee, William K

    2014-01-01

    A new design is proposed for an energy storing orthosis (ESO) that restores walking to people with spinal cord injury by combining functional electrical stimulation of the quadriceps muscle with a mechanical brace that uses elastic elements to store and transfer energy between hip and knee joints. The new ESO is a variation of a previous design and uses constant force springs for energy storage. Based on the detailed design and on dynamic simulations, the concept has demonstrated preliminary technical feasibility.

  6. Effect of Aging on the Mechanical Properties of Li-Ion Cell Components - A Preliminary Look

    Energy Technology Data Exchange (ETDEWEB)

    Cao, Lei; Zhang, Chao; Santhanagopalan, Shriram; Pesaran, Ahmad

    2016-05-03

    DOE/VTO/ES initiated the Computer Aided Engineering for Batteries (CAEBAT) in 2010. CAEBAT had a strong focus on building electrochemical-thermal models that simulate the performance of lithium-ion batteries. Since the start of CAEBAT-2 projects in FY14, our emphasis has been on safety aspects -- mechanical deformation in particular. This presentation gives a preliminary look at the effect of aging on the mechanical properties of lithium-ion cell components.

  7. ERIS: preliminary design phase overview

    Science.gov (United States)

    Kuntschner, Harald; Jochum, Lieselotte; Amico, Paola; Dekker, Johannes K.; Kerber, Florian; Marchetti, Enrico; Accardo, Matteo; Brast, Roland; Brinkmann, Martin; Conzelmann, Ralf D.; Delabre, Bernard A.; Duchateau, Michel; Fedrigo, Enrico; Finger, Gert; Frank, Christoph; Rodriguez, Fernando G.; Klein, Barbara; Knudstrup, Jens; Le Louarn, Miska; Lundin, Lars; Modigliani, Andrea; Müller, Michael; Neeser, Mark; Tordo, Sebastien; Valenti, Elena; Eisenhauer, Frank; Sturm, Eckhard; Feuchtgruber, Helmut; George, Elisabeth M.; Hartl, Michael; Hofmann, Reiner; Huber, Heinrich; Plattner, Markus P.; Schubert, Josef; Tarantik, Karl; Wiezorrek, Erich; Meyer, Michael R.; Quanz, Sascha P.; Glauser, Adrian M.; Weisz, Harald; Esposito, Simone; Xompero, Marco; Agapito, Guido; Antichi, Jacopo; Biliotti, Valdemaro; Bonaglia, Marco; Briguglio, Runa; Carbonaro, Luca; Cresci, Giovanni; Fini, Luca; Pinna, Enrico; Puglisi, Alfio T.; Quirós-Pacheco, Fernando; Riccardi, Armando; Di Rico, Gianluca; Arcidiacono, Carmelo; Dolci, Mauro

    2014-07-01

    The Enhanced Resolution Imager and Spectrograph (ERIS) is the next-generation adaptive optics near-IR imager and spectrograph for the Cassegrain focus of the Very Large Telescope (VLT) Unit Telescope 4, which will soon make full use of the Adaptive Optics Facility (AOF). It is a high-Strehl AO-assisted instrument that will use the Deformable Secondary Mirror (DSM) and the new Laser Guide Star Facility (4LGSF). The project has been approved for construction and has entered its preliminary design phase. ERIS will be constructed in a collaboration including the Max- Planck Institut für Extraterrestrische Physik, the Eidgenössische Technische Hochschule Zürich and the Osservatorio Astrofisico di Arcetri and will offer 1 - 5 μm imaging and 1 - 2.5 μm integral field spectroscopic capabilities with a high Strehl performance. Wavefront sensing can be carried out with an optical high-order NGS Pyramid wavefront sensor, or with a single laser in either an optical low-order NGS mode, or with a near-IR low-order mode sensor. Due to its highly sensitive visible wavefront sensor, and separate near-IR low-order mode, ERIS provides a large sky coverage with its 1' patrol field radius that can even include AO stars embedded in dust-enshrouded environments. As such it will replace, with a much improved single conjugated AO correction, the most scientifically important imaging modes offered by NACO (diffraction limited imaging in the J to M bands, Sparse Aperture Masking and Apodizing Phase Plate (APP) coronagraphy) and the integral field spectroscopy modes of SINFONI, whose instrumental module, SPIFFI, will be upgraded and re-used in ERIS. As part of the SPIFFI upgrade a new higher resolution grating and a science detector replacement are envisaged, as well as PLC driven motors. To accommodate ERIS at the Cassegrain focus, an extension of the telescope back focal length is required, with modifications of the guider arm assembly. In this paper we report on the status of the

  8. Simulation of surface processes.

    Science.gov (United States)

    Jónsson, Hannes

    2011-01-18

    Computer simulations of surface processes can reveal unexpected insight regarding atomic-scale structure and transitions. Here, the strengths and weaknesses of some commonly used approaches are reviewed as well as promising avenues for improvements. The electronic degrees of freedom are usually described by gradient-dependent functionals within Kohn-Sham density functional theory. Although this level of theory has been remarkably successful in numerous studies, several important problems require a more accurate theoretical description. It is important to develop new tools to make it possible to study, for example, localized defect states and band gaps in large and complex systems. Preliminary results presented here show that orbital density-dependent functionals provide a promising avenue, but they require the development of new numerical methods and substantial changes to codes designed for Kohn-Sham density functional theory. The nuclear degrees of freedom can, in most cases, be described by the classical equations of motion; however, they still pose a significant challenge, because the time scale of interesting transitions, which typically involve substantial free energy barriers, is much longer than the time scale of vibrations--often 10 orders of magnitude. Therefore, simulation of diffusion, structural annealing, and chemical reactions cannot be achieved with direct simulation of the classical dynamics. Alternative approaches are needed. One such approach is transition state theory as implemented in the adaptive kinetic Monte Carlo algorithm, which, thus far, has relied on the harmonic approximation but could be extended and made applicable to systems with rougher energy landscape and transitions through quantum mechanical tunneling.

  9. High Fidelity BWR Fuel Simulations

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Su Jong [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-08-01

    This report describes the Consortium for Advanced Simulation of Light Water Reactors (CASL) work conducted for completion of the Thermal Hydraulics Methods (THM) Level 3 milestone THM.CFD.P13.03: High Fidelity BWR Fuel Simulation. High fidelity computational fluid dynamics (CFD) simulation for Boiling Water Reactor (BWR) was conducted to investigate the applicability and robustness performance of BWR closures. As a preliminary study, a CFD model with simplified Ferrule spacer grid geometry of NUPEC BWR Full-size Fine-mesh Bundle Test (BFBT) benchmark has been implemented. Performance of multiphase segregated solver with baseline boiling closures has been evaluated. Although the mean values of void fraction and exit quality of CFD result for BFBT case 4101-61 agreed with experimental data, the local void distribution was not predicted accurately. The mesh quality was one of the critical factors to obtain converged result. The stability and robustness of the simulation was mainly affected by the mesh quality, combination of BWR closure models. In addition, the CFD modeling of fully-detailed spacer grid geometry with mixing vane is necessary for improving the accuracy of CFD simulation.

  10. Simulation Exercises

    Science.gov (United States)

    Tansey, Pat

    1976-01-01

    Describes five simulation exercises: a problem for a student teacher, an industrial relations game, a series of student problems; an international relations crisis, and a sociological exercise on public and private opinions. (LS)

  11. Computer Simulation of Multidimensional Archaeological Artefacts

    Directory of Open Access Journals (Sweden)

    Vera Moitinho de Almeida

    2012-11-01

    Our project focuses on the Neolithic lakeside site of La Draga (Banyoles, Catalonia. In this presentation we will begin by providing a clear overview of the major guidelines used to capture and process 3D digital data of several wooden artefacts. Then, we shall present the use of semi-automated relevant feature extractions. Finally, we intend to share preliminary computer simulation issues.

  12. Heat recovery and seed recovery development project: preliminary design report (PDR)

    Energy Technology Data Exchange (ETDEWEB)

    Arkett, A. H.; Alexander, K. C.; Bolek, A. D.; Blackman, B. K.; Kurrle, P. E.; Tram, S. V.; Warren, A. M.; Ziobrowski, A. J.

    1981-06-01

    The preliminary design and performance characteristics are described of the 20 MWt heat recovery and seed recovery (HRSR) system to be fabricated, installed, and evaluated to provide a technological basis for the design of commercial size HRSR systems for coal-fired open-cycle MHD power plants. The system description and heat and material balances, equipment description and functional requirements, controls, interfacing systems, and operation and maintenance are detailed. Appendices include: (1) recommended environmental requirements for compliance with federal and state of Tennessee regulations, (2) channel and diffuser simulator, (3) equipment arrangement drawings, and (4) channel and diffuser simulator barrel drawings. (WHK)

  13. HPS simulation and acceptance

    Energy Technology Data Exchange (ETDEWEB)

    Mundim, Luiz Martins [UERJ, Rio de Janeiro, RJ (Brazil); Pol, Maria Elena [CBPF, Rio de Janeiro, RJ (Brazil)

    2013-07-01

    Full text: The High Precision Spectrometer (HPS) is a proposal of sub-detector to be installed in the region of 200-240m from each side of CMS along the LHC beam-line to measure scattered protons from exclusive centrally produced processes, pp → p + X + p. In order to study the protons that reach the detectors, the beam-line of the LHC accelerator has to be taken into account, as the particles are deflected by dipoles and suffer the influence of quadrupoles and other beam devices. The LHC team provides a detailed description of these elements, currents, energies, magnetic fields, and all the information needed to study the propagation of the protons. The program HECTOR, developed at the University of Louvain, uses the information from LHC to calculate at any point along the beam-line the kinematic quantities that characterize the scattered protons. A simple minded program was initially developed for the preliminary studies of acceptances varying the position and size of the foreseen detectors. Also, it took into account vertex and position smearing, to simulate a realistic resolution of the tracking detectors. These studies were performed using a particle gun generator which shoot protons from the IP within reasonable ranges of possible t and ξ (the square of the four-momentum transfer and the fractional energy loss of the outgoing proton in a diffractive collision), and propagated them to the position of the tracking detectors. These kinematic quantities were reconstructed back at the IP using the transport equations from HECTOR. This simplified simulation was afterwards interfaced with the full software of CMS, CMSSW, in such a way that when a diffractive event was fully simulated and reconstructed in the central detector, the outgoing protons were treated by the HPS software and then the complete (CMS+HPS) event was output. The ExHuME generator was used to produce Monte Carlo simulations to study the mass acceptance of the HPS detector, and central and

  14. Hydrothermal Liquefaction Treatment Preliminary Hazard Analysis Report

    Energy Technology Data Exchange (ETDEWEB)

    Lowry, Peter P.; Wagner, Katie A.

    2015-08-31

    A preliminary hazard assessment was completed during February 2015 to evaluate the conceptual design of the modular hydrothermal liquefaction treatment system. The hazard assessment was performed in 2 stages. An initial assessment utilizing Hazard Identification and Preliminary Hazards Analysis (PHA) techniques identified areas with significant or unique hazards (process safety-related hazards) that fall outside of the normal operating envelope of PNNL and warranted additional analysis. The subsequent assessment was based on a qualitative What-If analysis. This analysis was augmented, as necessary, by additional quantitative analysis for scenarios involving a release of hazardous material or energy with the potential for affecting the public.

  15. A simulation tool for brassiness studies.

    Science.gov (United States)

    Gilbert, Joël; Menguy, Ludovic; Campbell, Murray

    2008-04-01

    A frequency-domain numerical model of brass instrument sound production is proposed as a tool to predict their brassiness, defined as the rate of spectral enrichment with increasing dynamic level. It is based on generalized Burger's equations dedicated to weakly nonlinear wave propagation in nonuniform ducts, and is an extension of previous work by Menguy and Gilbert [Acta Acustica 86, 798-810 (2000)], initially limited to short cylindrical tubes. The relevance of the present tool is evaluated by carrying out simulations over distances longer than typical shock formation distances, and by doing preliminary simulations of periodic regimes in a typical brass trombone bore geometry.

  16. Monte Carlo simulation for the transport beamline

    Energy Technology Data Exchange (ETDEWEB)

    Romano, F.; Cuttone, G.; Jia, S. B.; Varisano, A. [INFN, Laboratori Nazionali del Sud, Via Santa Sofia 62, Catania (Italy); Attili, A.; Marchetto, F.; Russo, G. [INFN, Sezione di Torino, Via P.Giuria, 1 10125 Torino (Italy); Cirrone, G. A. P.; Schillaci, F.; Scuderi, V. [INFN, Laboratori Nazionali del Sud, Via Santa Sofia 62, Catania, Italy and Institute of Physics Czech Academy of Science, ELI-Beamlines project, Na Slovance 2, Prague (Czech Republic); Carpinelli, M. [INFN Sezione di Cagliari, c/o Dipartimento di Fisica, Università di Cagliari, Cagliari (Italy); Tramontana, A. [INFN, Laboratori Nazionali del Sud, Via Santa Sofia 62, Catania, Italy and Università di Catania, Dipartimento di Fisica e Astronomia, Via S. Sofia 64, Catania (Italy)

    2013-07-26

    In the framework of the ELIMED project, Monte Carlo (MC) simulations are widely used to study the physical transport of charged particles generated by laser-target interactions and to preliminarily evaluate fluence and dose distributions. An energy selection system and the experimental setup for the TARANIS laser facility in Belfast (UK) have been already simulated with the GEANT4 (GEometry ANd Tracking) MC toolkit. Preliminary results are reported here. Future developments are planned to implement a MC based 3D treatment planning in order to optimize shots number and dose delivery.

  17. Plasma Simulation in the Multiphysics Object Oriented Simulation Environment MOOSE

    Science.gov (United States)

    Shannon, Steven; Lindsay, Alex; Graves, David; Icenhour, Casey; Peterson, David; White, Scott

    2016-09-01

    MOOSE is an open source multiphysics solver developed by Idaho National Laboratory that is primarily used for the simulation of fission reactor systems; the framework is also well suited for the simulation of plasma systems given the development of appropriate modules not currently developed in the framework such as electromagnetic solvers, Boltzmann solvers, etc. It is structured for user development of application specific modules and is intended for both workstation level and high performance massively parallel environments. We have begun the development of plasma modules in the MOOSE environment and carried out preliminary simulation of the plasma/liquid interface to elucidate coupling mechanisms between these states using a fully coupled multiphysics model; these results agree well with PIC simulation of the same system and show strong response of plasma parameters with respect to electron reflection at the liquid surface. These results will be presented along with an overview of MOOSE and ongoing module development to extend capabilities to a broader set of research challenges in low temperature plasmas, with particular focus on RF and pulsed RF driven systems.

  18. Mechanical Characterization and Finite Element Implementation of the SoftMaterials used in a Novel Anthropometric Test Device for SimulatingUnderbody Blast Loading

    Science.gov (United States)

    2017-09-14

    model simulations and corresponding experiments. In component simulations, the materials performed well and the model reasonably predicted the forces...strain-hardening proper- ties. A strong agreement was seen between the material model simulations and corresponding experiments. In component ...estimated in simulations where hyper- elastic material models were assigned to polymer components based on preliminary characterization tests. However

  19. Preliminary evaluation of the hydrogeologic system in Owens Valley, California

    Science.gov (United States)

    Danskin, W.R.

    1988-01-01

    A preliminary, two-layer, steady-state, groundwater flow model was used to evaluate present data and hydrologic concepts of Owens Valley, California. Simulations of the groundwater system indicate that areas where water levels are most affected by changes in recharge and discharge are near toes of alluvial fans and along the edge of permeable volcanic deposits. Sensitivity analysis for each model parameter shows that steady state simulations are most sensitive to uncertainties in evapotranspiration rates. Tungsten Hills, Poverty Hills, and Alabama Hills were found to act as virtually impermeable barriers to groundwater flow. Accurate simulation of the groundwater system between Bishop and Lone Pine appears to be possible without simulating the groundwater system in Round Valley, near Owens Lake, or in aquifer materials more than 1,000 ft below land surface. Although vast amounts of geologic and hydrologic data have been collected for Owens Valley, many parts of the hydrogeologic system have not been defined with sufficient detail to answer present water management questions. Location and extent of geologic materials that impede the vertical movement of water are poorly documented. The likely range of aquifer characteristics, except vertical hydraulic conductivity, is well known, but spatial distribution of these characteristics is not well documented. A set of consistent water budgets is needed, including one for surface water, groundwater, and the entire valley. The largest component of previous water budgets (evapotranspiration) is largely unverified. More definitive estimates of local gains and losses for Owens River are needed. Although groundwater pumpage from each well is measured, the quantity of withdrawal from different zones of permeable material has not been defined. (USGS)

  20. Preliminary designs: passive solar manufactured housing. Technical status report

    Energy Technology Data Exchange (ETDEWEB)

    1980-05-12

    The criteria established to guide the development of the preliminary designs are listed. Three preliminary designs incorporating direct gain and/or sunspace are presented. Costs, drawings, and supporting calculations are included. (MHR)

  1. Preliminary design package for Sunair SEC-601 solar collector

    Science.gov (United States)

    1978-01-01

    The preliminary design of the Owens-Illinois model Sunair SEC-601 tubular air solar collector is presented. Information in this package includes the subsystem design and development approaches, hazard analysis, and detailed drawings available as the preliminary design review.

  2. 19 CFR 4.8 - Preliminary entry.

    Science.gov (United States)

    2010-04-01

    ... electronic equivalent of a complete Customs Form 1302 (Cargo Declaration), in the manner provided in § 4.7(b... 19 Customs Duties 1 2010-04-01 2010-04-01 false Preliminary entry. 4.8 Section 4.8 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE...

  3. 40 CFR 1042.210 - Preliminary approval.

    Science.gov (United States)

    2010-07-01

    ... specific provisions that apply for deterioration factors. Decisions made under this section are considered... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Preliminary approval. 1042.210 Section 1042.210 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION...

  4. Preliminary aerothermodynamic design method for hypersonic vehicles

    Science.gov (United States)

    Harloff, G. J.; Petrie, S. L.

    1987-01-01

    Preliminary design methods are presented for vehicle aerothermodynamics. Predictions are made for Shuttle orbiter, a Mach 6 transport vehicle and a high-speed missile configuration. Rapid and accurate methods are discussed for obtaining aerodynamic coefficients and heat transfer rates for laminar and turbulent flows for vehicles at high angles of attack and hypersonic Mach numbers.

  5. 25 CFR 11.1005 - Preliminary inquiry.

    Science.gov (United States)

    2010-04-01

    ... ORDER CODE Juvenile Offender Procedure § 11.1005 Preliminary inquiry. (a) If a minor is placed in... purpose of determining: (1) Whether probable cause exist to believe the minor committed the alleged.... (b) If a minor has been released to the parents, guardian or custodian, the children's court shall...

  6. Preliminary aspects of a qualitative research projection

    Directory of Open Access Journals (Sweden)

    Simona Haidau

    2012-12-01

    Full Text Available In this paper are presented preliminary aspects on the design of of qualitative research achieved by nongovernmental organizations in the North-East of Romȃnia. The research aims to identify attitudes, opinions and behaviors to nongovernmental organizations to implement public relations programs and campaigns.

  7. 15 CFR 270.101 - Preliminary reconnaissance.

    Science.gov (United States)

    2010-01-01

    ... establishment of a Team, the leader of the initial assessment will report his/her findings to the Director in a... the extent the Director deems it appropriate, the Director may conduct a preliminary reconnaissance at the site of a building failure. The Director may establish and deploy a Team to conduct the...

  8. Preliminary investigations of piezoelectric based LED luminary

    DEFF Research Database (Denmark)

    Nielsen, Dennis; Andersen, Michael A. E.; Meyer, Kaspar Sinding

    2011-01-01

    This paper presents a preliminary study of PT (Piezoelectric Transformer) based SMPS’s (Switch Mode Power Supplies) for LED luminary. The unique properties of PTs (efficiency, power density and EMI) make them highly suitable for this application. Power stage topologies, rectifiers circuits, modul...

  9. Preliminary Results on Charmed Meson Spectroscopy

    CERN Document Server

    Sarwar, S; Paolone, V S; Reyes, M; Anjos, J C; Yager, P M; Bediaga, I; Göbel, C; Magnin, J; De Miranda, J M; Pepe, I M; Dos Reis, A C; Simão, F R A; Carrillo, S; Casimiro, E; Méndez, H; Sánchez-Hernández, A; Uribe, C; Vásquez, F; Cinquini, L; Cumalat, J P; Ramírez, J E; O'Reilly, B; Vaandering, E W; Butler, J N; Cheung, H W K; Gaines, I; Garbincius, P H; Garren, L A; Gottschalk, E E; Gourlay, S A; Kasper, P H; Kreymer, A E; Kutschke, R; Bianco, S; Fabbri, Franco Luigi; Sarwar, S; Cawlfield, C; Kim, D Y; Park, K S; Rahimi, A; Gardner, R; Chung, Y S; Kang, J S; Ko, B R; Kwak, J W; Lee, K B; Myung, S S; Alimonti, G; Boschini, M; Brambilla, D; Caccianiga, B; Calandrino, A; D'Angelo, P; Di Corato, M; Dini, P; Giammarchi, M G; Inzani, P; Leveraro, F; Malvezzi, S; Menasce, D; Mezzadri, M; Milazzo, L; Moroni, L; Pedrini, D; Prelz, F; Rovere, M; Sala, A; Sala, S; Arena, V; Boca, G; Bonomi, G; Gianini, G; Liguori, G; Merlo, M; Pantea, D; Ratti, S P; Riccardi, C; Torre, P; Viola, L; Vitulo, P; Hernández, Pilar; López, A M; Méndez, L; Mirles, M A; Montiel, E; Olaya, D; Quinones, J; Rivera, C; Zhang-Mayaguez, Y; Copty, N K; Purohit, M; Cho, K; Handler, T; Engh, D; Johns, W E; Hosack, M; Nehring, M S; Sales, M; Sheldon, P D; Stenson, K; Webster, M S; Sheaff, M; Kwon, Y; Sarwar, Shahzad

    2001-01-01

    We report the preliminary measurement by the FOCUS Collaboration (E831 at Fermilab) of masses and widths of the L=1 charm mesons $D_2^{*0}$ and $D_2^{*+}$. The fit of the invariant mass distribution requires an additional term to account for a broad structure over background.

  10. Preliminary Study on Airlift Membran—Bioreactor

    Institute of Scientific and Technical Information of China (English)

    XUNong; XINGWeihong; 等

    2002-01-01

    A new type of membrane bioreactor named “airlift membrane-bioreactor”is discussed.For municipal wastewater reclamation,the preliminary study on airlift membrane-bioreactor shows its good performance such as high flux and lower energy consumption.The airlift membrane-bioreactor is potentially applicable in bioengineering and environmental protection fields.

  11. A DESCRIPTIVE INDONESIAN GRAMMAR--PRELIMINARY EDITION.

    Science.gov (United States)

    DYEN, ISIDORE

    THIS PRELIMINARY EDITION COMPRISES A DESCRIPTIVE GRAMMAR OF INDONESIAN (BAHASA INDONESIA), THE OFFICIAL LANGUAGE OF THE REPUBLIC OF INDONESIA. THE THREE SECTIONS--PHONOLOGY, SYNTAX, AND MORPHOLOGY--PRESENT A COMPREHENSIVE LINGUISTIC ANALYSIS OF INDONESIAN, WITH OCCASIONAL CONTRASTIVE REFERENCE TO MALAY, JAVANESE, SUNDANESE, AND SUMATRAN. THIS…

  12. The Adaptation Gap Report - a Preliminary Assessment

    DEFF Research Database (Denmark)

    Alverson, Keith; Olhoff, Anne; Noble, Ian;

    This first Adaptation Gap report provides an equally sobering assessment of the gap between adaptation needs and reality, based on preliminary thinking on how baselines, future goals or targets, and gaps between them might be defined for climate change adaptation. The report focuses on gaps in de...... in developing countries in three important areas: finance, technology and knowledge....

  13. Numerical simulation of the fast dense gas Ludwieg tube experiment

    NARCIS (Netherlands)

    Zamfirescu, C.; Guerdone, A.; Collona, P.

    2006-01-01

    The preliminary design of a Ludwieg tube experiment for the verification of the existence of nonclassical rarefaction shock waves in dense vapors is here critically analyzed by means of real gas numerical simulations of the experimental setup. The Flexible Asymmetric Shock Tube (FAST) setup is a den

  14. Simulations of Precipitation Variability over the Upper Rio Grande Basin

    Energy Technology Data Exchange (ETDEWEB)

    Costigan, Keeley R.; Bossert, James E.; Langley, David L.

    1997-12-31

    In this research, we study Albuquerque`s water and how it may be affected by changes in the regional climate, as manifested by variations in Rio Grande water levels. To do this, we rely on the use of coupled atmospheric, runoff, and ground water models. Preliminary work on the project has focused on uncoupled simulations of the aquifer beneath Albuquerque and winter precipitation simulations of the upper Rio Grande Basin. The latter is discussed in this paper.

  15. Simulating Gravity

    Science.gov (United States)

    Pipinos, Savas

    2010-01-01

    This article describes one classroom activity in which the author simulates the Newtonian gravity, and employs the Euclidean Geometry with the use of new technologies (NT). The prerequisites for this activity were some knowledge of the formulae for a particle free fall in Physics and most certainly, a good understanding of the notion of similarity…

  16. Simulating Gravity

    Science.gov (United States)

    Pipinos, Savas

    2010-01-01

    This article describes one classroom activity in which the author simulates the Newtonian gravity, and employs the Euclidean Geometry with the use of new technologies (NT). The prerequisites for this activity were some knowledge of the formulae for a particle free fall in Physics and most certainly, a good understanding of the notion of similarity…

  17. ADDITIVE TESTING FOR IMPROVED SULFUR RETENTION: PRELIMINARY REPORT

    Energy Technology Data Exchange (ETDEWEB)

    Amoroso, J.; Fox, K.

    2011-09-07

    The Savannah River National Laboratory is collaborating with Alfred University to evaluate the potential for additives in borosilicate glass to improve sulfur retention. This preliminary report provides further background on the incorporation of sulfur in glass and outlines the experiments that are being performed by the collaborators. A simulated waste glass composition has been selected for the experimental studies. The first phase of experimental work will evaluate the impacts of BaO, PbO, and V{sub 2}O{sub 5} at concentrations of 1.0, 2.0, and 5.0 wt % on sulfate retention in simulated high level waste borosilicate glass. The second phase of experimental work will evaluate the effects of time at the melt temperature on sulfur retention. The resulting samples will be characterized to determine the amount of sulfur remaining as well as to identify the formation of any crystalline phases. The results will be used to guide the future selection of frits and glass forming chemicals in vitrifying Department of Energy wastes containing high sulfur concentrations.

  18. 32 CFR 644.30 - Preliminary real estate work.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 4 2010-07-01 2010-07-01 true Preliminary real estate work. 644.30 Section 644... PROPERTY REAL ESTATE HANDBOOK Project Planning Military (army and Air Force) and Other Federal Agencies § 644.30 Preliminary real estate work. (a) Preliminary real estate work is defined as that action taken...

  19. 29 CFR 1601.23 - Preliminary or temporary relief.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 4 2010-07-01 2010-07-01 false Preliminary or temporary relief. 1601.23 Section 1601.23... Employment Practices § 1601.23 Preliminary or temporary relief. (a) In the interest of the expeditious... subdivision, any recommendation for preliminary or temporary relief shall be transmitted directly to the...

  20. Preliminary study for small animal preclinical hadrontherapy facility

    Science.gov (United States)

    Russo, G.; Pisciotta, P.; Cirrone, G. A. P.; Romano, F.; Cammarata, F.; Marchese, V.; Forte, G. I.; Lamia, D.; Minafra, L.; Bravatá, V.; Acquaviva, R.; Gilardi, M. C.; Cuttone, G.

    2017-02-01

    Aim of this work is the study of the preliminary steps to perform a particle treatment of cancer cells inoculated in small animals and to realize a preclinical hadrontherapy facility. A well-defined dosimetric protocol was developed to explicate the steps needed in order to perform a precise proton irradiation in small animals and achieve a highly conformal dose into the target. A precise homemade positioning and holding system for small animals was designed and developed at INFN-LNS in Catania (Italy), where an accurate Monte Carlo simulation was developed, using Geant4 code to simulate the treatment in order to choose the best animal position and perform accurately all the necessary dosimetric evaluations. The Geant4 application can also be used to realize dosimetric studies and its peculiarity consists in the possibility to introduce the real target composition in the simulation using the DICOM micro-CT image. This application was fully validated comparing the results with the experimental measurements. The latter ones were performed at the CATANA (Centro di AdroTerapia e Applicazioni Nucleari Avanzate) facility at INFN-LNS by irradiating both PMMA and water solid phantom. Dosimetric measurements were performed using previously calibrated EBT3 Gafchromic films as a detector and the results were compared with the Geant4 simulation ones. In particular, two different types of dosimetric studies were performed: the first one involved irradiation of a phantom made up of water solid slabs where a layer of EBT3 was alternated with two different slabs in a sandwich configuration, in order to validate the dosimetric distribution. The second one involved irradiation of a PMMA phantom made up of a half hemisphere and some PMMA slabs in order to simulate a subcutaneous tumour configuration, normally used in preclinical studies. In order to evaluate the accordance between experimental and simulation results, two different statistical tests were made: Kolmogorov test and

  1. CUSUM control charts based on likelihood ratio for preliminary analysis

    Institute of Scientific and Technical Information of China (English)

    Yi DAI; Zhao-jun WANG; Chang-liang ZOU

    2007-01-01

    To detect and estimate a shift in either the mean and the deviation or both for the preliminary analysis, the statistical process control (SPC) tool, the control chart based on the likelihood ratio test (LRT), is the most popular method.Sullivan and woodall pointed out the test statistic lrt (n1, n2) is approximately distributed as x2 (2) as the sample size n, n1 and n2 are very large, and the value of n1 = 2, 3,..., n- 2 and that of n2 = n- n1.So it is inevitable that n1 or n2 is not large. In this paper the limit distribution of lrt(n1, n2) for fixed n1 or n2 is figured out, and the exactly analytic formulae for evaluating the expectation and the variance of the limit distribution are also obtained.In addition, the properties of the standardized likelihood ratio statistic slr(n1,n) are discussed in this paper. Although slr(n1, n) contains the most important information, slr(i, n)(i ≠ n1) also contains lots of information. The cumulative sum (CUSUM) control chart can obtain more information in this condition. So we propose two CUSUM control charts based on the likelihood ratio statistics for the preliminary analysis on the individual observations. One focuses on detecting the shifts in location in the historical data and the other is more general in detecting a shift in either the location and the scale or both.Moreover, the simulated results show that the proposed two control charts are, respectively, superior to their competitors not only in the detection of the sustained shifts but also in the detection of some other out-of-control situations considered in this paper.

  2. CUSUM control charts based on likelihood ratio for preliminary analysis

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    To detect and estimate a shift in either the mean and the deviation or both for the preliminary analysis, the statistical process control (SPC) tool, the control chart based on the likelihood ratio test (LRT), is the most popular method. Sullivan and woodall pointed out the test statistic lrt(n1, n2) is approximately distributed as x2(2) as the sample size n,n1 and n2 are very large, and the value of n1 = 2,3,..., n - 2 and that of n2 = n - n1. So it is inevitable that n1 or n2 is not large. In this paper the limit distribution of lrt(n1, n2) for fixed n1 or n2 is figured out, and the exactly analytic formulae for evaluating the expectation and the variance of the limit distribution are also obtained. In addition, the properties of the standardized likelihood ratio statistic slr(n1, n) are discussed in this paper. Although slr(n1, n) contains the most important information, slr(i, n)(i≠n1) also contains lots of information. The cumulative sum (CUSUM) control chart can obtain more information in this condition. So we propose two CUSUM control charts based on the likelihood ratio statistics for the preliminary analysis on the individual observations. One focuses on detecting the shifts in location in the historical data and the other is more general in detecting a shift in either the location and the scale or both. Moreover, the simulated results show that the proposed two control charts are, respectively, superior to their competitors not only in the detection of the sustained shifts but also in the detection of some other out-of-control situations considered in this paper.

  3. Preliminary Benefits Assessment of Traffic Aware Strategic Aircrew Requests (TASAR)

    Science.gov (United States)

    Henderson, Jeff; Idris, Husni; Wing, David J.

    2012-01-01

    While en route, aircrews submit trajectory change requests to air traffic control (ATC) to better meet their objectives including reduced delays, reduced fuel burn, and passenger comfort. Aircrew requests are currently made with limited to no information on surrounding traffic. Consequently, these requests are uninformed about a key ATC objective, ensuring traffic separation, and therefore less likely to be accepted than requests informed by surrounding traffic and that avoids creating conflicts. This paper studies the benefits of providing aircrews with on-board decision support to generate optimized trajectory requests that are probed and cleared of known separation violations prior to issuing the request to ATC. These informed requests are referred to as traffic aware strategic aircrew requests (TASAR) and leverage traffic surveillance information available through Automatic Dependent Surveillance Broadcast (ADS-B) In capability. Preliminary fast-time simulation results show increased benefits with longer stage lengths since beneficial trajectory changes can be applied over a longer distance. Also, larger benefits were experienced between large hub airports as compared to other airport sizes. On average, an aircraft equipped with TASAR reduced its travel time by about one to four minutes per operation and fuel burn by about 50 to 550 lbs per operation depending on the objective of the aircrew (time, fuel, or weighted combination of time and fuel), class of airspace user, and aircraft type. These preliminary results are based on analysis of approximately one week of traffic in July 2012 and additional analysis is planned on a larger data set to confirm these initial findings.

  4. Preliminary Design Through Graphs: A Tool for Automatic Layout Distribution

    Directory of Open Access Journals (Sweden)

    Carlo Biagini

    2015-02-01

    Full Text Available Diagrams are essential in the preliminary stages of design for understanding distributive aspects and assisting the decision-making process. By drawing a schematic graph, designers can visualize in a synthetic way the relationships between many aspects: functions and spaces, distribution of layouts, space adjacency, influence of traffic flows within a facility layout, and so on. This process can be automated through the use of modern Information and Communication Technologies tools (ICT that allow the designers to manage a large quantity of information. The work that we will present is part of an on-going research project into how modern parametric software influences decision-making on the basis of automatic and optimized layout distribution. The method involves two phases: the first aims to define the ontological relation between spaces, with particular reference to a specific building typology (rules of aggregation of spaces; the second entails the implementation of these rules through the use of specialist software. The generation of ontological relations begins with the collection of data from historical manuals and analyses of case studies. These analyses aim to generate a “relationship matrix” based on preferences of space adjacency. The phase of implementing the previously defined rules is based on the use of Grasshopper to analyse and visualize different layout configurations. The layout is generated by simulating a process involving the collision of spheres, which represents specific functions of the design program. The spheres are attracted or rejected as a function of the relationships matrix, as defined above. The layout thus obtained will remain in a sort of abstract state independent of information about the exterior form, but will still provide a useful tool for the decision-making process. In addition, preliminary results gathered through the analysis of case studies will be presented. These results provide a good variety

  5. RCS Simulation

    Science.gov (United States)

    2005-05-01

    store config.) to be considered, Moving parts to be considered · Hybridisation of methods · Fast algorithms, new Aproaches · Geometry representations...Page 2 Military Aircraft Overview • Introduction • Methods ,Tools for mm-wave applications • Examples • Further requirements / developments Page 3...Flexible handling of Geometry · Parametrisation of Geometry Page 4 Military Aircraft Methods for RCS simulations •Fundamental subdivision between full

  6. DSN Simulator

    Science.gov (United States)

    Fijany, Amir; Vatan, Farrokh; Barrett, Anthony; James, Mark; Mackey, Ryan; Williams, Colin

    2009-01-01

    The DSN Simulator (wherein DSN signifies NASA's Deep Space Network) is an updated version of the software described in DSN Array Simulator (NPO-44506), Software Tech Briefs (Special supplement to NASA Tech Briefs), Vol. 32, No. 9 (September 2008), page 26. To recapitulate: This software is used for computational modeling of proposed DSN facilities comprising arrays of antennas and transmitting and receiving equipment for microwave communication with spacecraft on interplanetary missions. Such modeling is performed to estimate facility performance, evaluate requirements that govern facility design, and evaluate proposed improvements in hardware and/or software. The software includes a Monte Carlo simulation component that enables rapid generation of key mission-set metrics (e.g., numbers of links, data rates, and data volumes), and statistical distributions thereof as functions of time. The prior version of the software could model only one DSN facility at a time and included hard-coded, unconfigurable metrics. The present updated version is capable of modeling the entire DSN and provides for configurable metrics, making it possible to perform loading analyses for alternative future DSN architectures and mission-set scenarios. The present version also features an improved user interface and interfaces for exchange of data with other DSN software and with a DSN mission model database.

  7. Simulation and Preliminary Validation of China' s Temperature in a Decade by RegCM3%RegCM3模式对中国近10年来气温变化的模拟实验及检验

    Institute of Scientific and Technical Information of China (English)

    杜吴鹏; 高庆先; 师华定; 孙丹; 房小怡

    2012-01-01

    In recent years, global climate change has become a hot issue concerned and studied by domestic and foreign atmospheric scientists. The change of temperature is the most significant characteristic as well as the most direct consequence of climate change. Extreme weather and climate occurrs more and more frequently in the recent decade, which will have great potential impacts on many regions especially climate-sensitive areas. The research of temperature simulation and validation can help to assess the model applicability systematically as well as can be used as reference for improvment and perfection of the model. The data used in this research come from the simulation results of ten years (2000-2009) obtained by Regional Climate Model and the relevant meteorological observation data from 752 stations. The research methods are mainly mathematical statistics, comparison and analysis as well as correlation validation. In this paper, temperature and its change in the recent decade (2000-2009) in China were first simulated by RegCM3, and then the results were validated preliminarily and analyzed in detail based on meteorological observation data. The results show that the model can simulate the temperature distribution, gradient changes and obvious high temperature centers in general, and the simulation results of central and eastern China are better than western China, such as Qinghai-Tibet Plateau and Sinkiang. The temperature change simulations of 2005-2009 at representative meteorological stations are consistent with those of 2000-2004, which indicates that the model has a certain simulation capability of regional climate change. Further validation shows that the model can simulate the annual and seasonal temperature change as a whole, and the simulation results are better in Northeast China and North China than in other regions. However, there is a phenomenon of systematically low value, especially for high temperature season in northern China and low temperature

  8. Experimental natural circulation circuit - preliminaries results; Circuito experimental de circulacao natural - resultados experimentais preliminares

    Energy Technology Data Exchange (ETDEWEB)

    Faccini, Jose Luiz H.; Botelho, David A.; Soares, Milton; Coutinho, Jorge A.; Freitas, Sergio Carlos [Instituto de Engenharia Nuclear (IEN), Rio de Janeiro, RJ (Brazil). E-mail: faccini@cnen.gov.br

    2000-07-01

    These are the preliminaries results of the tests carried out at experimental natural circulation system of IEN/CNEN. The experimental system is a reduced scale similar model in power, pressure, and length of a passive residual heat removal prototype system. It enables studies of natural circulation phenomena in an advanced PWR. The experimental results refer to the steps of data acquisition system calibration, power control system calibration, and single-phase operational tests. The results of single-phase tests show temperature in time measured by the thermocouples placed along the natural circulation system. It is also presented a brief commentary on the experimental results, based on theory and preliminary computational simulations. (author)

  9. Preliminary results in surgery of Parkinson's disease.

    Science.gov (United States)

    Nasser, J A; Confort, C I; Ferraz, A; Bouza, A A

    1998-09-01

    The authors present the preliminary results of 20 patients selected to be operated on between January 1996 and April 1997. These patients presented one of the present indications for stereotactic posteroventral pallidotomy (PVP), such as: rigidity, akinesia/bradykinesia, gait dysfunction, drug induced dyskinesias and tremor. Every patient of this protocol was evaluated by: UPDRS score, Schwab and England scale, Hoehn and Yahr Staging Scale before and after surgery. The results in 3 months showed a remarkable improvement after PVP (P < 0.01) in all functional assessments, except for facial expression, speech and posture. The morbidity was 5%. 5 patients (25%) who were in Hoehn and Yahr 5 underwent a bilateral simultaneous PVP. In 5 patients (25%), who had tremor, during the PVP, VIM thalamotomy was added. These preliminary results, suggest that PVP is highly effective for PD symptoms.

  10. Rare earth optogalvanic spectroscopy: preliminary results

    Energy Technology Data Exchange (ETDEWEB)

    Destro, Marcelo G.; Neri, Jose W.; Rodrigues, Nicolau A.S.; Silveira, Carlos A.B.; Riva, Rudimar [Instituto de Estudos Avancados (IEAv/EFO), Sao Jose dos Campos, SP (Brazil). Div. de Fotonica]. E-mail: destro@ieav.cta.br; Victor, Alessandro R. [Instituto Tecnologico de Aeronautica (ITA), Sao Jose dos Campos, SP (Brazil)

    2008-07-01

    The IEAv has special interest in the studies of rare earth isotope applications in laser medium and integrated optics as well as aerospace research. We are starting to work with Ytterbium, Erbium, Dysprosium and Neodymium laser selective photoionization research. This paper describes the preliminary results of emission and optogalvanic spectroscopy obtained from a Neodymium hollow cathode lamps. Furthermore these results were used to setup our laser systems to work to leads a Nd isotopes selective laser photoionization. (author)

  11. Institutional Repositories in India: A preliminary study

    OpenAIRE

    2011-01-01

    This preliminary study investigates various aspects of institutional repositories (IR’s) developed in India. The present study has identified the existence of 16 functional IRs some of which were not registered in any of the directories such as ROAR, Open DOAR. The study explores the timeline involved in planning, pilot testing, to system implementation of IR, exploratory activities conducted before implementing IR, its anticipated benefits.

  12. A Toolbox for Rotorcraft Preliminary Design

    OpenAIRE

    Lier, Max; Krenik, Alex; Kunze, Philipp; Kohlgrüber, Dieter; Schwinn, Dominik; Lützenberger, Marius

    2015-01-01

    The German Aerospace Center (DLR) developed a toolbox, which is able to reflect the conceptual and preliminary design process of rotorcraft configuration. Such a toolbox is a valuable aid for the design engineer and can be used for the assessment of new technologies with regard to the overall configuration. This toolbox is currently extended to model novel rotorcraft configurations. Automated optimization procedures will be added in the future as well. This paper describes the too...

  13. Preliminary rock mechanics laboratory: Investigation plan

    Energy Technology Data Exchange (ETDEWEB)

    Oschman, K.P.; Hummeldorf, R.G.; Hume, H.R.; Karakouzian, M.; Vakili, J.E.

    1987-01-01

    This document presents the rationale for rock mechanics laboratory testing (including the supporting analysis and numerical modeling) planned for the site characterization of a nuclear waste repository in salt. This plan first identifies what information is required for regulatory and design purposes, and then presents the rationale for the testing that satisfies the required information needs. A preliminary estimate of the minimum sampling requirements for rock laboratory testing during site characterization is also presented. Periodic revision of this document is planned.

  14. Preliminary safety analysis methodology for the SMART

    Energy Technology Data Exchange (ETDEWEB)

    Bae, Kyoo Hwan; Chung, Y. J.; Kim, H. C.; Sim, S. K.; Lee, W. J.; Chung, B. D.; Song, J. H. [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2000-03-01

    This technical report was prepared for a preliminary safety analysis methodology of the 330MWt SMART (System-integrated Modular Advanced ReacTor) which has been developed by Korea Atomic Energy Research Institute (KAERI) and funded by the Ministry of Science and Technology (MOST) since July 1996. This preliminary safety analysis methodology has been used to identify an envelope for the safety of the SMART conceptual design. As the SMART design evolves, further validated final safety analysis methodology will be developed. Current licensing safety analysis methodology of the Westinghouse and KSNPP PWRs operating and under development in Korea as well as the Russian licensing safety analysis methodology for the integral reactors have been reviewed and compared to develop the preliminary SMART safety analysis methodology. SMART design characteristics and safety systems have been reviewed against licensing practices of the PWRs operating or KNGR (Korean Next Generation Reactor) under construction in Korea. Detailed safety analysis methodology has been developed for the potential SMART limiting events of main steam line break, main feedwater pipe break, loss of reactor coolant flow, CEA withdrawal, primary to secondary pipe break and the small break loss of coolant accident. SMART preliminary safety analysis methodology will be further developed and validated in parallel with the safety analysis codes as the SMART design further evolves. Validated safety analysis methodology will be submitted to MOST as a Topical Report for a review of the SMART licensing safety analysis methodology. Thus, it is recommended for the nuclear regulatory authority to establish regulatory guides and criteria for the integral reactor. 22 refs., 18 figs., 16 tabs. (Author)

  15. PLANT COMMUNITIES OF ALBANIA - A PRELIMINARY OVERVIEW

    Directory of Open Access Journals (Sweden)

    J. DRING

    2002-04-01

    Full Text Available The phytosociological analysis of Albania was initiated by F. Markgraf in the 30ies, but still remains incomplete. This is a preliminary list of the plant communities resulting from the literature and from field research carried out during the last years and may represent a first contribution for further research. Many communities are described only by dominant species, other are quoted as nomina nuda. Some further syntaxa. probably present in the study area, are added.

  16. PLANT COMMUNITIES OF ALBANIA - A PRELIMINARY OVERVIEW

    Directory of Open Access Journals (Sweden)

    J, RODWELL

    2002-01-01

    Full Text Available The phytosociological analysis of Albania was initiated by F. Markgraf in the 30ies, but still remains incomplete. This is a preliminary list of the plant communities resulting from the literature and from field research carried out during the last years and may represent a first contribution for further research. Many communities are described only by dominant species, other are quoted as nomina nuda. Some further syntaxa. probably present in the study area, are added.

  17. [Tonsillectomy with a laser dissector. Preliminary report].

    Science.gov (United States)

    Lenz, H

    1984-11-01

    A so called laser-dissector with a flexible beam guide system for tonsillectomy is described. With this instrument the tissue is irradiated for a very short time resulting in a coagulation of the peritonsillar tissue with closure of the small vessels even before mechanical dissection is performed. A preliminary report of 10 patients is given. The main advantage is that the procedure could be performed without or with much less bleeding as in tonsillectomy without using vasoconstrictors.

  18. Preliminary Analysis of Google+'s Privacy

    OpenAIRE

    2011-01-01

    In this paper we provide a preliminary analysis of Google+ privacy. We identified that Google+ shares photo metadata with users who can access the photograph and discuss its potential impact on privacy. We also identified that Google+ encourages the provision of other names including maiden name, which may help criminals performing identity theft. We show that Facebook lists are a superset of Google+ circles, both functionally and logically, even though Google+ provides a better user interfac...

  19. Preliminary prediction of inflow into the D-holes at the Stripa Mine

    Energy Technology Data Exchange (ETDEWEB)

    Long, J.C.S.; Karasaki, K.; Davey, A.; Peterson, J.; Landsfeld, M.; Kemeny, J.; Martel, S.

    1990-02-01

    Lawrence Berkeley Laboratory (LBL) is contracted by the US Department of Energy to provide an auxiliary modeling effort for the Stripa Project. Within this effort, we are making calculations of inflow to the Simulated Drift Experiment (SDE), i.e. inflow to six parallel, closely spaced D-holes, using a preliminary set of data collected in five other holes, the N- and W-holes during Stages 1 and 2 of the Site Characterization and Validation (SCV) project. Our approach has been to focus on the fracture zones rather than the general set of ubiquitous fractures. Approximately 90% of all the water flowing in the rock is flowing in fracture zones which are neither uniformly conductive nor are they infinitely extensive. Our approach has been to adopt the fracture zone locations as they have been identified with geophysics. We use geologic sense and the original geophysical data to add one zone where significant water inflow has been observed that can not be explained with the other geophysical zones. This report covers LBL's preliminary prediction of flow into the D-holes. Care should be taken in interpreting the results given in this report. As explained below, the approach that LBL has designed for developing a fracture hydrology model requires cross-hole hydrologic data. Cross-hole tests are planned for Stage 3 but were unavailable in Stage 1. As such, we have inferred from available data what a cross-hole test might show and used this synthetic data to make a preliminary calculation of the inflow into the D-holes. Then using all the Stage 3 data we will calculate flow into the Validation Drift itself. The report mainly demonstrates the use of our methodology and the simulated results should be considered preliminary.

  20. Electromagnetic fields produced by simulated spacecraft discharges

    Science.gov (United States)

    Nonevicz, J. E.; Adamo, R. C.; Beers, B. L.; Delmer, T. N.

    1980-01-01

    The initial phase of a broader, more complete program for the characterization of electrical breakdowns on spacecraft insulating materials is described which consisted of the development of a discharge simulator and characterization facility and the performance of a limited number of discharge measurements to verify the operation of the laboratory setup and to provide preliminary discharge transient field data. A preliminary model of the electromagnetic characteristics of the discharge was developed. It is based upon the "blow off" current model of discharges, with the underlying assumption of a propagating discharge. The laboratory test facility and discharge characterization instrumentation are discussed and the general results of the "quick look" tests are described on quartz solar reflectors aluminized Kapton and silver coated Teflon are described.

  1. Flight Simulation.

    Science.gov (United States)

    1986-09-01

    G.B.Churchill 12 SIMULATION DES COMMANDES DE VOL ELECTRIQES AU CENTRE D’ESSAIS EN VOL FRANAIS (CEV) POUR LES AVIONS DE TRANSPORT CIVIL par R.Vadrot 13 Reference...rapid advancements in the state-of-the-art will have a positive impact on both civil and military aerospace planners. In summary, this conference clearly...pilotes at des inginieurs du Bureau d’Etudes Systime d’Aroes : l disposent anfin d’un mayan puissant de dialogue entre concapteurs at utilisateurs. La

  2. Neuromechanical simulation

    Directory of Open Access Journals (Sweden)

    Donald H Edwards

    2010-07-01

    Full Text Available The importance of the interaction between the body and the brain for the control of behavior has been recognized in recent years with the advent of neuromechanics, a field in which the coupling between neural and biomechanical processes is an explicit focus. A major tool used in neuromechanics is simulation, which connects computational models of neural circuits to models of an animal’s body situated in a virtual physical world. This connection closes the feedback loop that links the brain, the body, and the world through sensory stimuli, muscle contractions and body movement. Neuromechanical simulations enable investigators to explore the dynamical relationships between the brain, the body, and the world in ways that are difficult or impossible through experiment alone. Studies in a variety of animals have permitted the analysis of extremely complex and dynamic neuromechanical systems, they have demonstrated that the nervous system functions synergistically with the mechanical properties of the body, they have examined hypotheses that are difficult to test experimentally, and they have explored the role of sensory feedback in controlling complex mechanical systems with many degrees of freedom. Each of these studies confronts a common set of questions: (i how to abstract key features of the body, the world and the CNS in a useful model, (ii how to ground model parameters in experimental reality, (iii how to optimize the model and identify points of sensitivity and insensitivity, and (iv how to share neuromechanical models for examination, testing, and extension by others.

  3. Discharging Part of LNG Liquid Cargo Handling Simulator

    Directory of Open Access Journals (Sweden)

    Zhen-Zhou Yang

    2013-09-01

    Full Text Available With the development of the national economy, it is important to develop LNG (Liquefied Natural Gas liquid cargo handling simulator. In this paper, the discharging part of Liquid Cargo Handling Simulator of LNG Carriers is developed by Visual Basic. The system includes 5 major forms and 3 mathematical models such as cargo pump model, the pressure and temperature model of the LNG vapour in the cargo tank and the liquid level model. The system can complete the unloading task. The system has become a preliminary model of LNG liquid cargo handlings simulator training.

  4. 2-D SIMULATION OF CHANNEL FLOWS WITH MOVEABLE BED

    Institute of Scientific and Technical Information of China (English)

    Wilhelm BECHTELER; Davood FARSHI

    2001-01-01

    This paper presents some preliminary results of 2-D numerical simulation of open channel flow with moveable bed. The unsteady two dimensional channel flow and sediment transport are simulated by solving shallow water equations and sediment continuity equation in conservation form based on unstructured finite volume method. Redefining longitudinal and transverse slopes of the bed is implemented in order to consider them in the bedload equation. A simple modeling treatment dealing with secondary flow effect on sediment movement is also discussed. Finally, two examples of numerical simulation are presented.

  5. Virtual simulation of maneuvering captive tests for a surface vessel

    Directory of Open Access Journals (Sweden)

    Ahmad Hajivand

    2015-09-01

    Full Text Available Hydrodynamic derivatives or coefficients are required to predict the maneuvering characteristics of a marine vehicle. These derivatives are obtained numerically for a DTMB 5512 model ship by virtual simulating of captive model tests in a CFD environment. The computed coefficients are applied to predict the turning circle and zigzag maneuvers of the model ship. The comparison of the simulated results with the available experimental data shows a very good agreement among them. The simulations show that the CFD is precise and affordable tool at the preliminary design stage to obtain maneuverability performance of a marine vehicles.

  6. Acoustic Simulation with Dynamic Mechanisms in Virtual Reality

    Institute of Scientific and Technical Information of China (English)

    张琼; 石教英

    1998-01-01

    Although most investigators have realized the importance of acoustic simulation in sophisticated VR systems,large computational load involved in this process often contradicts the requirements of real-time interaction,which in return bring on applying the expensive hardware or VR-specific workstations to this area.In order to reduce the computational cost and try to realize the real-time acoustic simulation in software with (or even without)some low-cost hardware,this paper proposes some dynamic mechanisms which can be used as possible strategies embedded into acoustic simulation in VR.Preliminary implementation of those mechanisms has proved to be fairly effective.

  7. Chemistry and preliminary environmental effects of mixtures of triisopropyl phosphite, Bis-(2-ethylexyl)-phosphonate, and sulfur. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Cataldo, D.A.; Harvey, S.D.; McVeety, B.D.; Fellows, R.J.; Van Noris, P.

    1991-12-01

    The present studies were performed to evaluate the reaction chemistry and preliminary biotic impacts of BIS, TIP, and TIPS. Reaction chemistry studies were designed to simulate in-flight mixing characteristics. The binary mixture undergoes rapid and nearly complete reaction. The final products released to the environment are TIPS and excess elemental sulfur. There is an apparent species sensitivity difference in algae for the simulants BIS, TIP, and TIPS, with Chlorella being more sensitive than Selenastrum based on cell number studies. However, the extent of adverse effects was not excessive for either algal species. There was no apparent effect of TIP or TIPS on the electron transport systems of isolated chloroplasts at the concentration tested (10 ppm). In general, it is unlikely that environmental release of these products would have significant or lasting effects, based on the preliminary algal tests and electron transport studies.

  8. Preliminary Verification and Validation of WEC-Sim, an Open-Source Wave Energy Converter Design Tool: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Ruehl, K.; Michelen, C.; Kanner, S.; Lawson, M.; Yu, Y. H.

    2014-03-01

    To promote and support the wave energy industry, a wave energy converter (WEC) design tool, WEC-Sim, is being developed by Sandia National Laboratories and the National Renewable Energy Laboratory. In this paper, the WEC-Sim code is used to model a point absorber WEC designed by the U.S. Department of Energy's reference model project. Preliminary verification was performed by comparing results of the WEC-Sim simulation through a code-to-code comparison, utilizing the commercial codes ANSYS-AQWA, WaveDyn, and OrcaFlex. A preliminary validation of the code was also performed by comparing WEC-Sim simulation results to experimental wave tank tests.

  9. Large co-axial pulse tube preliminary results

    Science.gov (United States)

    Emery, N.; Caughley, A.; Meier, J.; Nation, M.; Tanchon, J.; Trollier, T.; Ravex, A.

    2014-01-01

    We report that Callaghan Innovation, formally known as Industrial Research Ltd (IRL), has designed and built its largest of three high frequency single-stage co-axial pulse tubes, closely coupled to a metal diaphragm pressure wave generator (PWG). The previous pulse tube achieved 110 W of cooling power @ 77 K, with an electrical input power of 3.1 kW from a 90 cc swept volume PWG. The pulse tubes have all been tuned to operate at 50 Hz, with a mean helium working pressure of 2.5 MPa. Sage pulse tube simulation software was used to model the latest pulse tube and predicted 280 W of cooling power @ 77 K. The nominal 250 W cryocooler was designed to be an intermediate step to up-scale pulse tube technology for our 1000 cc swept-volume PWG, to provide liquefaction of gases and cooling for HTS applications. Details of the modeling, design, development and preliminary experimental results are discussed.

  10. A PRELIMINARY STUDY OF EXPERT SYSTEM FOR MINING UNDER STRUCTURES

    Institute of Scientific and Technical Information of China (English)

    吴侃; 何国清; 曹立明

    1991-01-01

    The expert system MUST (Mining Under Structures) shown in this paper and established by the authors is a preliminary expert system to solve the policy-making problems formining under structures by means of computers instead of humanbeing. Based on the experience of relative experts,the authors established a knowledge base about the minings under structures ,researched into reasonable method to simulate thinking processes of human experts when they are solvin8 the problems, established the network of an expert system and named it'MUST system'MUST system uses the method of the structural system analysis approach. A kind of methods of Turbo Prolog and Fortran 77 language alternations is designed to meet the needs of exchange information within the MUST system. Based on this kind of methods MUST system has been constructed and realised on IBM-PC computer. For verifying the correctness. suitability and reliablity of MUST system,some practical examples of minings under structures were tentatively solved using MUST system ,whose results are satisfactory.

  11. Preliminary study on mechanics-based rainfall kinetic energy

    Directory of Open Access Journals (Sweden)

    Yuan Jiuqin Ms.

    2014-09-01

    Full Text Available A raindrop impact power observation system was employed to observe the real-time raindrop impact power during a rainfall event and to analyze the corresponding rainfall characteristics. The experiments were conducted at different simulated rainfall intensities. As rainfall intensity increased, the observed impact power increased linearly indicating the power observation system would be satisfactory for characterizing rainfall erosivity. Momentum is the product of mass and velocity (Momentum=MV, which is related to the observed impact power value. Since there is no significant difference between momentum and impact power, observed impact power can represent momentum for different rainfall intensities. The relationship between momentum and the observed impact power provides a convenient way to calculate rainfall kinetic energy. The value of rainfall kinetic energy based on the observed impact power was higher than the classic rainfall kinetic energy. The rainfall impact power based kinetic energy and the classic rainfall kinetic energy showed linear correlation, which indicates that the raindrop impact power observation system can characterize rainfall kinetic energy. The article establishes a preliminary way to calculate rainfall kinetic energy by using the real-time observed momentum, providing a foundation for replacing the traditional methods for estimating kinetic energy of rainstorms.

  12. A Preliminary Study on 1D Numerical Experiment of Water Debris Flow in Gully

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    In order to improve and enhance the numerical modeling methods and its application on debris flow problems,a preliminary study has been proposed in accordance with the corrected water-sediment numerical model on the premise of revised resistance and sediment capacity equations.Firstly,an overview the recent re- search achievements on numerical simulation of debris flow has been conducted,the results shown that a gener- al numerical model for debris flow can not be existed at all because the complex rheol...

  13. Effects of implant angulation, material selection, and impression technique on impression accuracy: a preliminary laboratory study.

    Science.gov (United States)

    Rutkunas, Vygandas; Sveikata, Kestutis; Savickas, Raimondas

    2012-01-01

    The aim of this preliminary laboratory study was to evaluate the effects of 5- and 25-degree implant angulations in simulated clinical casts on an impression's accuracy when using different impression materials and tray selections. A convenience sample of each implant angulation group was selected for both open and closed trays in combination with one polyether and two polyvinyl siloxane impression materials. The influence of material and technique appeared to be significant for both 5- and 25-degree angulations (P impression accuracy. The open-tray technique was more accurate with highly nonaxially oriented implants for the small sample size investigated.

  14. Spinel dissolution via addition of glass forming chemicals. Results of preliminary experiments

    Energy Technology Data Exchange (ETDEWEB)

    Fox, K. M. [Savannah River Site (SRS), Aiken, SC (United States); Johnson, F. C. [Savannah River Site (SRS), Aiken, SC (United States)

    2015-11-01

    Increased loading of high level waste in glass can lead to crystallization within the glass. Some crystalline species, such as spinel, have no practical impact on the chemical durability of the glass, and therefore may be acceptable from both a processing and a product performance standpoint. In order to operate a melter with a controlled amount of crystallization, options must be developed for remediating an unacceptable accumulation of crystals. This report describes preliminary experiments designed to evaluate the ability to dissolve spinel crystals in simulated waste glass melts via the addition of glass forming chemicals (GFCs).

  15. Preliminary analysis of Alvito-Odivelas reservoir system operation under climate change scenarios

    OpenAIRE

    2008-01-01

    The present study provides a preliminary analysis of the impact of climate change on a water resources system of Alentejo region in the South of Portugal. Regional climate model HadRM3P forced by the Global Circulation Model HadAM3P A2 of the Hadley Centre, is used to derive temperature and precipitation data, which in turn is used as input to hydrological model (SHETRAN) for simulation of future streamflow. Dynamic programming based models are used for operation of reservoir system in order ...

  16. Preliminary Experimental Results for Indirect Vector-Control of Induction Motor Drives with Forced Dynamics

    Directory of Open Access Journals (Sweden)

    Jan Vittek

    2003-01-01

    Full Text Available The contribution presents an extension of indirect vector control of electric drives employing induction motors to 'Forced Dynamic Control'. This method of control offers an accurate realisation of dynamic response profiles, which can be selected by the user. The developed system can be integrated into a drive with a shaft position encoder or a shaft sensoriess drive, in which only the stator currents are measured. The applied stator voltages are determined by a computed inverter switching algorithm. Simulation results and preliminary experimental results for indirect vector control of an idle running induction motor indicate good agreement with the theoretical predictions.

  17. Frictional sliding in layered rock model: Preliminary experiments. Yucca Mountain Site Characterization Project

    Energy Technology Data Exchange (ETDEWEB)

    Perry, K.E. Jr.; Buescher, B.J.; Anderson, D.; Epstein, J.S. [Idaho National Engineering Lab., Idaho Falls, ID (United States)

    1995-09-01

    An important aspect of determining the suitability of Yucca Mountain as a possible nuclear waste repository requires understanding the mechanical behavior of jointed rock-masses. To this end we have studied the frictional sliding between simulated rock joints in the laboratory using the technique of phase shifting moire interferometry. The models were made from stacks of Lexan plates and contained a central hole to induce slip between the plates when the models were loaded in compression. These preliminary results confirm the feasibility of the approach and show a clear evolution of slip as function of load.

  18. Preliminary design of a coffee harvester

    Directory of Open Access Journals (Sweden)

    Raphael Magalhães Gomes Moreira

    2016-10-01

    Full Text Available Design of an agricultural machine is a highly complex process due to interactions between the operator, machine, and environment. Mountain coffee plantations constitute an economic sector that requires huge investments for the development of agricultural machinery to improve the harvesting and post-harvesting processes and to overcome the scarcity of work forces in the fields. The aim of this study was to develop a preliminary design for a virtual prototype of a coffee fruit harvester. In this study, a project methodology was applied and adapted for the development of the following steps: project planning, informational design, conceptual design, and preliminary design. The construction of a morphological matrix made it possible to obtain a list of different mechanisms with specific functions. The union between these mechanisms resulted in variants, which were weighed to attribute scores for each selected criterion. From each designated proposal, two variants with the best scores were selected and this permitted the preparation of the preliminary design of both variants. The archetype was divided in two parts, namely the hydraulically articulated arms and the harvesting system that consisted of the vibration mechanism and the detachment mechanism. The proposed innovation involves the use of parallel rods, which were fixed in a plane and rectangular metal sheet. In this step, dimensions including a maximum length of 4.7 m, a minimum length of 3.3 m, and a total height of 2.15 m were identified based on the functioning of the harvester in relation to the coupling point of the tractor.

  19. Traffic and Driving Simulator Based on Architecture of Interactive Motion.

    Science.gov (United States)

    Paz, Alexander; Veeramisti, Naveen; Khaddar, Romesh; de la Fuente-Mella, Hanns; Modorcea, Luiza

    2015-01-01

    This study proposes an architecture for an interactive motion-based traffic simulation environment. In order to enhance modeling realism involving actual human beings, the proposed architecture integrates multiple types of simulation, including: (i) motion-based driving simulation, (ii) pedestrian simulation, (iii) motorcycling and bicycling simulation, and (iv) traffic flow simulation. The architecture has been designed to enable the simulation of the entire network; as a result, the actual driver, pedestrian, and bike rider can navigate anywhere in the system. In addition, the background traffic interacts with the actual human beings. This is accomplished by using a hybrid mesomicroscopic traffic flow simulation modeling approach. The mesoscopic traffic flow simulation model loads the results of a user equilibrium traffic assignment solution and propagates the corresponding traffic through the entire system. The microscopic traffic flow simulation model provides background traffic around the vicinities where actual human beings are navigating the system. The two traffic flow simulation models interact continuously to update system conditions based on the interactions between actual humans and the fully simulated entities. Implementation efforts are currently in progress and some preliminary tests of individual components have been conducted. The implementation of the proposed architecture faces significant challenges ranging from multiplatform and multilanguage integration to multievent communication and coordination.

  20. Traffic and Driving Simulator Based on Architecture of Interactive Motion

    Directory of Open Access Journals (Sweden)

    Alexander Paz

    2015-01-01

    Full Text Available This study proposes an architecture for an interactive motion-based traffic simulation environment. In order to enhance modeling realism involving actual human beings, the proposed architecture integrates multiple types of simulation, including: (i motion-based driving simulation, (ii pedestrian simulation, (iii motorcycling and bicycling simulation, and (iv traffic flow simulation. The architecture has been designed to enable the simulation of the entire network; as a result, the actual driver, pedestrian, and bike rider can navigate anywhere in the system. In addition, the background traffic interacts with the actual human beings. This is accomplished by using a hybrid mesomicroscopic traffic flow simulation modeling approach. The mesoscopic traffic flow simulation model loads the results of a user equilibrium traffic assignment solution and propagates the corresponding traffic through the entire system. The microscopic traffic flow simulation model provides background traffic around the vicinities where actual human beings are navigating the system. The two traffic flow simulation models interact continuously to update system conditions based on the interactions between actual humans and the fully simulated entities. Implementation efforts are currently in progress and some preliminary tests of individual components have been conducted. The implementation of the proposed architecture faces significant challenges ranging from multiplatform and multilanguage integration to multievent communication and coordination.

  1. Preliminary investigations of piezoelectric based LED luminary

    DEFF Research Database (Denmark)

    Nielsen, Dennis; Andersen, Michael A. E.; Meyer, Kaspar Sinding

    2011-01-01

    This paper presents a preliminary study of PT (Piezoelectric Transformer) based SMPS’s (Switch Mode Power Supplies) for LED luminary. The unique properties of PTs (efficiency, power density and EMI) make them highly suitable for this application. Power stage topologies, rectifiers circuits......, modulation schemes, LEDs and LED driving conditions are analyzed. A prototype radial mode PT optimized for ZVS (Zero Voltage Switching) is designed. FEM (Final Element Method) and measurements validates the PT design. A prototype PT based AC/DC converter operating from european mains is proposed...

  2. PRELIMINARY PROGRAMMED WHOLE—BODY COUNTER

    Institute of Scientific and Technical Information of China (English)

    张少东; 郑文忠; 等

    1995-01-01

    It is capable of giving the initial intakes of radionuclides and the assessment quantitites used in radiation protection according to its measured results of radionuclides in vivo.It is accomplished by providing the software of controlling,interface and internal dose estimation programs to the original iron cabin shielding whole-body counter.The preliminary application shows that its data processing is rapid and correct,and can meet the requirement of rapid internal radioactive contamination monitoring and diagnosing in case of lots of internal contamination subjects happened in nuclear accident.

  3. Underwater Munitions Expert System: Preliminary Design Report

    Science.gov (United States)

    2015-08-21

    coral   reefs ,  can  be  added  to  future  versions  of  UnMES.     For  this  preliminary  UnMES...administer  areas   polluted  by  discarded  munitions.    Towards  this  end,  SERDP  is   sponsoring   the   development...estimating   seawater   pollution   from   dissolved   chemical   components  of  munitions.    

  4. Preliminary results from a new spin spectrometer

    Energy Technology Data Exchange (ETDEWEB)

    Tobin, J.G.; Bedrossian, P.J. [Lawrence Livermore National Lab., CA (United States); Cummins, T.R. [Univ. of Missouri, Rolla, MO (United States). Dept. of Physics] [and others

    1998-12-31

    The first preliminary results from a novel spectrometer for elementally-specific measurements of magnetic surfaces and ultrathin films are presented here. The key measurements are based upon spin-resolving and photon-dichroic photoelectron spectroscopy. True spin-resolution is achieved by the use of a Mini-Mott detection scheme. The photon-dichroic measurements include the variant magnetic x-ray linear dichroism (MXLD). Both a multi-channel, energy dispersive collection scheme as well as the spin-detecting Mini-Mott apparatus are used in data collection. The Spin Spectrometer is based at the Spectromicroscopy Facility (Beamline 7) at the Advanced Light Source.

  5. preliminary study of American legal culture

    Institute of Scientific and Technical Information of China (English)

    周杨

    2016-01-01

    This thesis is a preliminary study of American legal culture. Nowadays more and more scholars see the importance of legal culture and do studies on it. The author selects a number of American legal TV plays and movies; analyzes their topics, main characters, and plots; then finds out why United States adopt the legal system; what kind of legal culture it has; and how the legal culture is reflected in those movies and TV plays. The author hopes this thesis can work not only as an insight into the American legal culture, but also a source of reference for china to improve its legal system.

  6. Ecological economics - a special perspective? Preliminary reflections

    DEFF Research Database (Denmark)

    Røpke, Inge

    2002-01-01

    This paper reports on some preliminary reflections from a research project concerning ecological economics as a special perspective. As Clive Spash noted in a presentation at the ESEE conference in Cambridge, July 2001, ecological economics has reached the age of puberty, looks into the glass...... and searches its own identity. The identity seeking processes are visible in the large number of publications discussing the characteristics of ecological economics as well as the similarities to and differences from environmental economics. The present paper is a part of this stream. The paper is work...

  7. Preliminary results on nonparametric facial occlusion detection

    Directory of Open Access Journals (Sweden)

    Daniel LÓPEZ SÁNCHEZ

    2016-10-01

    Full Text Available The problem of face recognition has been extensively studied in the available literature, however, some aspects of this field require further research. The design and implementation of face recognition systems that can efficiently handle unconstrained conditions (e.g. pose variations, illumination, partial occlusion... is still an area under active research. This work focuses on the design of a new nonparametric occlusion detection technique. In addition, we present some preliminary results that indicate that the proposed technique might be useful to face recognition systems, allowing them to dynamically discard occluded face parts.

  8. 33 CFR 127.315 - Preliminary transfer inspection.

    Science.gov (United States)

    2010-07-01

    ... (CONTINUED) WATERFRONT FACILITIES WATERFRONT FACILITIES HANDLING LIQUEFIED NATURAL GAS AND LIQUEFIED HAZARDOUS GAS Waterfront Facilities Handling Liquefied Natural Gas Operations § 127.315 Preliminary...

  9. QCD simulations with staggered fermions on GPUs

    CERN Document Server

    Bonati, C; D'Elia, M; Incardona, P

    2011-01-01

    We report on our implementation of the RHMC algorithm for the simulation of lattice QCD with two staggered flavors on Graphics Processing Units, using the NVIDIA CUDA programming language. The main feature of our code is that the GPU is not used just as an accelerator, but instead the whole Molecular Dynamics trajectory is performed on it. After pointing out the main bottlenecks and how to circumvent them, we discuss the obtained performances. We present some preliminary results regarding OpenCL and multiGPU extensions of our code and discuss future perspectives.

  10. Preliminary Study of the Mesoscale Numerical Simulation of the Rain Mitigation Operation during the Opening Ceremony of the 2008 Beijing Olympic Games%2008年奥运会开幕式日人工消减雨作业中尺度数值模拟的初步结果

    Institute of Scientific and Technical Information of China (English)

    何晖; 金华; 李宏宇; 刘建忠

    2012-01-01

    simulate the rain mitigation operation which was carried out during 2005 LST - 2012 LST. The seeding effect of the different seeding rate and the microphysical mechanism is analyzed. The results show that different seeding rates have much influence on the surface precipitation. When the seeding operation lasts seven minutes with seeding rate 5 g·s-1, the surface rainfall is suppressed in two hours and enhanced after two hours. The microphysical mechanism of the rainfall decreasing is the depletion of supercooled water after Agl is injected into the cloud, the graupel content decreases and then the rain water decreases. While the microphysical mechanism of the rainfall increased two hours after seeding operation is just because a positive feedback link is formed among the rain water, cloud water, graupel, and the temperature, which finally leads to the increase of surface rainfall. But it should be noted that for the limitation of the single-moment cloud scheme, the maximum rainfall reduction being of only 8%- 12%, there is a certain gap between the goal of the rain mitigation and the simulation result. It is necessary to further simulation with the double-moment cloud scheme.

  11. Preliminary Results of Field Emission Cathode Tests

    Science.gov (United States)

    Sovey, James S.; Kovaleski, Scott D.

    2001-01-01

    Preliminary screening tests of field emission cathodes such as chemical vapor deposited (CVD) diamond, textured pyrolytic graphite, and textured copper were conducted at background pressures typical of electric thruster test facilities to assess cathode performance and stability. Very low power electric thrusters which provide tens to hundreds micronewtons of thrust may need field emission neutralizers that have a capability of tens to hundreds of microamperes. From current voltage characteristics, it was found that the CVD diamond and textured metals cathodes clearly satisfied the Fowler-Nordheim emission relation. The CVD diamond and a textured copper cathode had average current densities of 270 and 380 mA/sq cm, respectively, at the beginning-of-life. After a few hours of operation the cathode emission currents degraded by 40 to 75% at background pressures in the 10(exp -5) Pa to 10(exp -4) Pa range. The textured pyrolytic graphite had a modest current density at beginning-of-life of 84 mA/sq cm, but this cathode was the most stable of all. Extended testing of the most promising cathodes is warranted to determine if current degradation is a burn-in effect or whether it is a long-term degradation process. Preliminary experiments with ferroelectric emission cathodes, which are ceramics with spontaneous electric polarization, were conducted. Peak current densities of 30 to 120 mA/sq cm were obtained for pulse durations of about 500 ns in the 10(exp -4) Pa pressure range.

  12. Defining resilience: A preliminary integrative literature review

    Science.gov (United States)

    Wilt, Bonnie; Long, Suzanna K.; Shoberg, Thomas G.

    2016-01-01

    The term “resilience” is ubiquitous in technical literature; it appears in numerous forms, such as resilience, resiliency, or resilient, and each use may have a different definition depending on the interpretation of the writer. This creates difficulties in understanding what is meant by ‘resilience’ in any given use case, especially in discussions of interdisciplinary research. To better understand this problem, this research constructs a preliminary integrative literature review to map different definitions, applications and calculation methods of resilience invoked within critical infrastructure applications. The preliminary review uses a State-of-the-Art Matrix (SAM) analysis to characterize differences in definition across disciplines and between regions. Qualifying the various usages of resilience will produce a greater precision in the literature and a deeper insight into types of data required for its evaluation, particularly with respect to critical infrastructure calculations and how such data may be analyzed. Results from this SAM analysis will create a framework of key concepts as part of the most common applications for “resilient critical infrastructure” modeling.

  13. Preliminary impression techniques for microstomia patients.

    Science.gov (United States)

    Kumar, K Aswini; Bhat, Vinaya; Nair, K Chandrasekheran; Suresh, Reshma

    2016-01-01

    The Prosthetic rehabilitation of microstomia patients presents difficulties at all the stages. The difficulty starts with the preliminary impression making. This is due to the tongue rigidity and the decreased oral opening. A maximum oral opening which is smaller than the size of the tray can make prosthetic treatment challenging. Due to the restricted mouth opening, insertion and removal of the impression trays is extremely cumbersome and various modifications of the trays have been used in the past. Among these are the flexible trays and the sectional trays used with different modes of reassembling the segments extra orally after the impression is made. This article reviews the literature published from 1971 to 2015 concerning preliminary impression techniques used in making impressions for patients with microstomia based on various tray designs. An electronic search was performed across three databases (PubMed, Science Direct and Google Scolar) for relevant citations. The keywords/combinations used for the search were microstomia, limited/constricted/restricted mouth opening/oral access, trismus, sectional trays, impressions and prosthetic/prosthodontic rehabilitation. The search was limited to papers written in English which resulted in a total of 45 related articles of which 17 articles were included for discussion of this review.

  14. Fabrication of preliminary fuel rods for SFR

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sun Ki; Oh, Seok Jin; Ko, Young Mo; Woo, Youn Myung; Kim, Ki Hwan [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2012-05-15

    Metal fuels was selected for fueling many of the first reactors in the US, including the Experimental Breeder Reactor-I (EBR-I) and the Experimental Breeder Reactor-II (EBR-II) in Idaho, the FERMI-I reactor, and the Dounreay Fast Reactor (DFR) in the UK. Metallic U.Pu.Zr alloys were the reference fuel for the US Integral Fast Reactor (IFR) program. Metallic fuel has advantages such as simple fabrication procedures, good neutron economy, high thermal conductivity, excellent compatibility with a Na coolant and inherent passive safety. U-Zr-Pu alloy fuels have been used for SFR (sodium-cooled fast reactor) related to the closed fuel cycle for managing minor actinides and reducing a high radioactivity levels since the 1980s. Fabrication technology of metallic fuel for SFR has been in development in Korea as a national nuclear R and D program since 2007. For the final goal of SFR fuel rod fabrication with good performance, recently, three preliminary fuel rods were fabricated. In this paper, the preliminary fuel rods were fabricated, and then the inspection for QC(quality control) of the fuel rods was performed

  15. Ship design methodologies of preliminary design

    CERN Document Server

    Papanikolaou, Apostolos

    2014-01-01

    This book deals with ship design and in particular with methodologies of the preliminary design of ships. The book is complemented by a basic bibliography and five appendices with useful updated charts for the selection of the main dimensions and other basic characteristics of different types of ships (Appendix A), the determination of hull form  from the data of systematic hull form series (Appendix B), the detailed description of the relational method for the preliminary estimation of ship weights (Appendix C), a brief review of the historical evolution of shipbuilding science and technology from the prehistoric era to date (Appendix D) and finally a historical review of regulatory developments of ship's damage stability to date (Appendix E).  The book can be used as textbook for ship design courses or as additional reading for university or college students of naval architecture courses and related disciplines; it may also serve as a reference book for naval architects, practicing engineers of rel...

  16. Preliminary design for a maglev development facility

    Energy Technology Data Exchange (ETDEWEB)

    Coffey, H.T.; He, J.L.; Chang, S.L.; Bouillard, J.X.; Chen, S.S.; Cai, Y.; Hoppie, L.O.; Lottes, S.A.; Rote, D.M. [Argonne National Lab., IL (United States); Zhang, Z.Y. [Polytechnic Univ., Brooklyn, NY (United States); Myers, G.; Cvercko, A. [Sterling Engineering, Westchester, IL (United States); Williams, J.R. [Alfred Benesch and Co., Chicago, IL (United States)

    1992-04-01

    A preliminary design was made of a national user facility for evaluating magnetic-levitation (maglev) technologies in sizes intermediate between laboratory experiments and full-scale systems. A technical advisory committee was established and a conference was held to obtain advice on the potential requirements of operational systems and how the facility might best be configured to test these requirements. The effort included studies of multiple concepts for levitating, guiding, and propelling maglev vehicles, as well as the controls, communications, and data-acquisition and -reduction equipment that would be required in operating the facility. Preliminary designs for versatile, dual 2-MVA power supplies capable of powering attractive or repulsive systems were developed. Facility site requirements were identified. Test vehicles would be about 7.4 m (25 ft) long, would weigh form 3 to 7 metric tons, and would operate at speeds up to 67 m/s (150 mph) on a 3.3-km (2.05-mi) elevated guideway. The facility would utilize modular vehicles and guideways, permitting the substitution of levitation, propulsion, and guideway components of different designs and materials for evaluation. The vehicle would provide a test cell in which individual suspension or propulsion components or subsystems could be tested under realistic conditions. The system would allow economical evaluation of integrated systems under varying weather conditions and in realistic geometries.

  17. A preliminary neutron crystallographic study of thaumatin

    Energy Technology Data Exchange (ETDEWEB)

    Teixeira, Susana C. M. [ILL-EMBL Deuteration Laboratory, Partnership for Structural Biology, 6 Rue Jules Horowitz, 38042 Grenoble (France); Institut Laue Langevin, 6 Rue Jules Horowitz, 38042 Grenoble (France); EPSAM and ISTM, Keele University, Staffordshire ST5 5BG (United Kingdom); Blakeley, Matthew P. [Institut Laue Langevin, 6 Rue Jules Horowitz, 38042 Grenoble (France); Leal, Ricardo M. F. [ILL-EMBL Deuteration Laboratory, Partnership for Structural Biology, 6 Rue Jules Horowitz, 38042 Grenoble (France); Institut Laue Langevin, 6 Rue Jules Horowitz, 38042 Grenoble (France); EPSAM and ISTM, Keele University, Staffordshire ST5 5BG (United Kingdom); ESRF, 6 Rue Jules Horowitz, BP-220, 38043 Grenoble (France); Mitchell, Edward P. [EPSAM and ISTM, Keele University, Staffordshire ST5 5BG (United Kingdom); ESRF, 6 Rue Jules Horowitz, BP-220, 38043 Grenoble (France); Forsyth, V. Trevor, E-mail: tforsyth@ill.fr [ILL-EMBL Deuteration Laboratory, Partnership for Structural Biology, 6 Rue Jules Horowitz, 38042 Grenoble (France); Institut Laue Langevin, 6 Rue Jules Horowitz, 38042 Grenoble (France); EPSAM and ISTM, Keele University, Staffordshire ST5 5BG (United Kingdom)

    2008-05-01

    Preliminary neutron crystallographic data from the sweet protein thaumatin have been recorded using the LADI-III diffractometer at the Institut Laue Langevin (ILL). The results illustrate the feasibility of a full neutron structural analysis aimed at further understanding the molecular basis of the perception of sweet taste. Such an analysis will exploit the use of perdeuterated thaumatin. A preliminary neutron crystallographic study of the sweet protein thaumatin is presented. Large hydrogenated crystals were prepared in deuterated crystallization buffer using the gel-acupuncture method. Data were collected to a resolution of 2 Å on the LADI-III diffractometer at the Institut Laue Langevin (ILL). The results demonstrate the feasibility of a full neutron crystallographic analysis of this structure aimed at providing relevant information on the location of H atoms, the distribution of charge on the protein surface and localized water in the structure. This information will be of interest for understanding the specificity of thaumatin–receptor interactions and will contribute to further understanding of the molecular mechanisms underlying the perception of taste.

  18. Preliminary impression techniques for microstomia patients

    Directory of Open Access Journals (Sweden)

    K Aswini Kumar

    2016-01-01

    Full Text Available The Prosthetic rehabilitation of microstomia patients presents difficulties at all the stages. The difficulty starts with the preliminary impression making. This is due to the tongue rigidity and the decreased oral opening. A maximum oral opening which is smaller than the size of the tray can make prosthetic treatment challenging. Due to the restricted mouth opening, insertion and removal of the impression trays is extremely cumbersome and various modifications of the trays have been used in the past. Among these are the flexible trays and the sectional trays used with different modes of reassembling the segments extra orally after the impression is made. This article reviews the literature published from 1971 to 2015 concerning preliminary impression techniques used in making impressions for patients with microstomia based on various tray designs. An electronic search was performed across three databases (PubMed, Science Direct and Google Scolar for relevant citations. The keywords/combinations used for the search were microstomia, limited/constricted/restricted mouth opening/oral access, trismus, sectional trays, impressions and prosthetic/prosthodontic rehabilitation. The search was limited to papers written in English which resulted in a total of 45 related articles of which 17 articles were included for discussion of this review.

  19. Preliminary design for a maglev development facility

    Energy Technology Data Exchange (ETDEWEB)

    Coffey, H.T.; He, J.L.; Chang, S.L.; Bouillard, J.X.; Chen, S.S.; Cai, Y.; Hoppie, L.O.; Lottes, S.A.; Rote, D.M. (Argonne National Lab., IL (United States)); Zhang, Z.Y. (Polytechnic Univ., Brooklyn, NY (United States)); Myers, G.; Cvercko, A. (Sterling Engineering, Westchester, IL (United States)); Williams, J.R. (Alfred Benesch and Co., Chicago, IL (United States))

    1992-04-01

    A preliminary design was made of a national user facility for evaluating magnetic-levitation (maglev) technologies in sizes intermediate between laboratory experiments and full-scale systems. A technical advisory committee was established and a conference was held to obtain advice on the potential requirements of operational systems and how the facility might best be configured to test these requirements. The effort included studies of multiple concepts for levitating, guiding, and propelling maglev vehicles, as well as the controls, communications, and data-acquisition and -reduction equipment that would be required in operating the facility. Preliminary designs for versatile, dual 2-MVA power supplies capable of powering attractive or repulsive systems were developed. Facility site requirements were identified. Test vehicles would be about 7.4 m (25 ft) long, would weigh form 3 to 7 metric tons, and would operate at speeds up to 67 m/s (150 mph) on a 3.3-km (2.05-mi) elevated guideway. The facility would utilize modular vehicles and guideways, permitting the substitution of levitation, propulsion, and guideway components of different designs and materials for evaluation. The vehicle would provide a test cell in which individual suspension or propulsion components or subsystems could be tested under realistic conditions. The system would allow economical evaluation of integrated systems under varying weather conditions and in realistic geometries.

  20. Preliminary Hazards Analysis Plasma Hearth Process

    Energy Technology Data Exchange (ETDEWEB)

    Aycock, M.; Coordes, D.; Russell, J.; TenBrook, W.; Yimbo, P. [Science Applications International Corp., Pleasanton, CA (United States)

    1993-11-01

    This Preliminary Hazards Analysis (PHA) for the Plasma Hearth Process (PHP) follows the requirements of United States Department of Energy (DOE) Order 5480.23 (DOE, 1992a), DOE Order 5480.21 (DOE, 1991d), DOE Order 5480.22 (DOE, 1992c), DOE Order 5481.1B (DOE, 1986), and the guidance provided in DOE Standards DOE-STD-1027-92 (DOE, 1992b). Consideration is given to ft proposed regulations published as 10 CFR 830 (DOE, 1993) and DOE Safety Guide SG 830.110 (DOE, 1992b). The purpose of performing a PRA is to establish an initial hazard categorization for a DOE nuclear facility and to identify those processes and structures which may have an impact on or be important to safety. The PHA is typically performed during and provides input to project conceptual design. The PRA then is followed by a Preliminary Safety Analysis Report (PSAR) performed during Title I and II design. This PSAR then leads to performance of the Final Safety Analysis Report performed during construction, testing, and acceptance and completed before routine operation. Radiological assessments indicate that a PHP facility, depending on the radioactive material inventory, may be an exempt, Category 3, or Category 2 facility. The calculated impacts would result in no significant impact to offsite personnel or the environment. Hazardous material assessments indicate that a PHP facility will be a Low Hazard facility having no significant impacts either onsite or offsite to personnel and the environment.

  1. Preliminary design for a MAGLEV development facility

    Science.gov (United States)

    Coffey, H. T.; He, J. L.; Chang, S. L.; Bouillard, J. X.; Chen, S. S.; Cai, Y.; Hoppie, L. O.; Lottes, S. A.; Rote, D. M.; Zhang, Z. Y.

    1992-04-01

    A preliminary design was made of a national user facility for evaluating magnetic-levitation (maglev) technologies in sizes intermediate between laboratory experiments and full-scale systems. A technical advisory committee was established and a conference was held to obtain advice on the potential requirements of operational systems and how the facility might best be configured to test these requirements. The effort included studies of multiple concepts for levitating, guiding, and propelling maglev vehicles, as well as the controls, communications, and data-acquisition and -reduction equipment that would be required in operating the facility. Preliminary designs for versatile, dual 2-MVA power supplies capable of powering attractive or repulsive systems were developed. Facility site requirements were identified. Test vehicles would be about 7.4 m (25 ft) long, would weigh from 3 to 7 metric tons, and would operate at speeds up to 67 m/s (150 mph) on a 3.3-km (2.05-mi) elevated guideway. The facility would utilize modular vehicles and guideways, permitting the substitution of levitation, propulsion, and guideway components of different designs and materials for evaluation. The vehicle would provide a test cell in which individual suspension or propulsion components or subsystems could be tested under realistic conditions. The system would allow economical evaluation of integrated systems under varying weather conditions and in realistic geometries.

  2. Preliminary results of ground-motion characteristics

    Directory of Open Access Journals (Sweden)

    Francesca Bozzoni

    2012-10-01

    Full Text Available The preliminary results are presented herein for the engineering applications of the characteristics of the ground motion induced by the May 20, 2012, Emilia earthquake. Shake maps are computed to provide estimates of the spatial distribution of the induced ground motion. The signals recorded at the Mirandola (MRN station, the closest to the epicenter, have been processed to obtain acceleration, velocity and displacement response spectra. Ground-motion parameters from the MRN recordings are compared with the corresponding estimates from recent ground-motion prediction equations, and with the spectra prescribed by the current Italian Building Code for different return periods. The records from the MRN station are used to plot the particle orbit (hodogram described by the waveform. The availability of results from geotechnical field tests that were performed at a few sites in the Municipality of Mirandola prior to this earthquake of May 2012 has allowed preliminary assessment of the ground response. The amplification effects at Mirandola are estimated using fully stochastic site-response analyses. The seismic input comprises seven actual records that are compatible with the Italian code-based spectrum that refers to a 475-year return period. The computed acceleration response spectrum and the associated dispersion are compared to the spectra calculated from the recordings of the MRN station. Good agreement is obtained for periods up to 1 s, especially for the peak ground acceleration. For the other periods, the spectral acceleration of the MRN recordings exceeds that of the computed spectra.

  3. ISSA/TSS power preliminary design

    Science.gov (United States)

    Main, John A.

    1996-01-01

    A projected power shortfall during the initial utilization flights of the International Space Station Alpha (ISSA) has prompted an inquiry into the use of the Tethered Satellite System (TSS) to provide station power. The preliminary design of the combined ISSA/TSS system is currently underway in the Preliminary Design Office at the Marshall Space Flight Center. This document focuses on the justification for using a tether system on space station, the physical principles behind such a system, and how it might be operated to best utilize its capabilities. The basic components of a simple DC generator are a magnet of some type and a conductive wire. Moving the wire through the magnetic field causes forces to be applied to the electric charges in the conductor, and thus current is induced to flow. This simple concept is the idea behind generating power with space-borne tether systems. The function of the magnet is performed by the earth's magnetic field, and orbiting a conductive tether about the earth effectively moves the tether through the field.

  4. Simulator fidelity and training effectiveness: a comprehensive bibliography with selected annotations

    Energy Technology Data Exchange (ETDEWEB)

    Rankin, W.L.; Bolton, P.A.; Shikiar, R.; Saari, L.M.

    1984-05-01

    This document contains a comprehensive bibliography on the topic of simulator fidelity and training effectiveness, prepared during the preliminary phases of work on an NRC-sponsored project on the Role of Nuclear Power Plant Simulators in Operator Licensing and Training. Section A of the document is an annotated bibliography consisting of articles and reports with relevance to the psychological aspects of simulator fidelity and the effectiveness of training simulators in a variety of settings, including military. The annotated items are drawn from a more comprehensive bibliography, presented in Section B, listing documents treating the role of simulators in operator training both in the nuclear industry and elsewhere.

  5. Architectural and operational considerations emerging from hybrid RF-optical network loading simulations

    Science.gov (United States)

    Chen, Yijiang; Abraham, Douglas S.; Heckman, David P.; Kwok, Andrew; MacNeal, Bruce E.; Tran, Kristy; Wu, Janet P.

    2016-03-01

    A technology demonstration of free space optical communication at interplanetary distances is planned via one or more future NASA deep-space missions. Such demonstrations will "pave the way" for operational use of optical communications on future robotic/potential Human missions. Hence, the Deep Space Network architecture will need to evolve. Preliminary attempts to model the anticipated future mission set and simulate how well it loads onto assumed architectures with combinations of RF and optical apertures have been evaluated. This paper discusses the results of preliminary loading simulations for hybrid RF-optical network architectures and highlights key mission and ground infrastructure considerations that emerge.

  6. 2012 Annual Report: Simulate and Evaluate the Cesium Transport and Accumulation in Fukushima-Area Rivers by the TODAM Code

    Energy Technology Data Exchange (ETDEWEB)

    Onishi, Yasuo; Yokuda, Satoru T.

    2013-03-28

    Pacific Northwest National Laboratory initiated the application of the time-varying, one-dimensional sediment-contaminant transport code, TODAM (Time-dependent, One-dimensional, Degradation, And Migration) to simulate the cesium migration and accumulation in the Ukedo River in Fukushima. This report describes the preliminary TODAM simulation results of the Ukedo River model from the location below the Ougaki Dam to the river mouth at the Pacific Ocean. The major findings of the 100-hour TODAM simulation of the preliminary Ukedo River modeling are summarized as follows:

  7. Towards Real Time Simulation of Ship-Ship Interaction

    DEFF Research Database (Denmark)

    Lindberg, Ole; Bingham, Harry B.; Engsig-Karup, Allan Peter

    2012-01-01

    We present recent and preliminary work directed towards the development of a simplified, physics-based model for improved simulation of ship-ship interaction that can be used for both analysis and real-time computing (i.e. with real-time constraints due to visualization). The goal is to implement...... the model into a large maritime simulator for training of naval officers, in particular tug boat helmsmen. Tug boat simulators are used for training of communication and situation awareness during manoeuvre involved with towing of large vessels. A main objective of the work is to improve and enable more...... accurate (realistic) and much faster ship-wave and ship-ship simulations than are currently possible. The coupling of simulation with visualization should improve the visual experience such that it can be perceived as more realistic in training. Today the state-of-art in real-time ship-ship interaction...

  8. Preliminary criteria for the very early diagnosis of systemic sclerosis

    DEFF Research Database (Denmark)

    Avouac, J; Fransen, Julie Munk; Walker, U A

    2011-01-01

    To identify a core set of preliminary items considered as important for the very early diagnosis of systemic sclerosis (SSc).......To identify a core set of preliminary items considered as important for the very early diagnosis of systemic sclerosis (SSc)....

  9. 40 CFR 8.6 - Preliminary environmental review.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Preliminary environmental review. 8.6 Section 8.6 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GENERAL ENVIRONMENTAL IMPACT ASSESSMENT OF NONGOVERNMENTAL ACTIVITIES IN ANTARCTICA § 8.6 Preliminary environmental review. (a) Unless an...

  10. Preliminary design of pseudo satellites: Basic methods and feasibility criteria

    Science.gov (United States)

    Klimenko, N. N.

    2016-12-01

    Analytical models of weight and energy balances, aerodynamic models, and solar irradiance models to perform pseudo-satellite preliminary design are presented. Feasibility criteria are determined in accordance with the aim of preliminary design dependent on mission scenario and type of payload.

  11. 28 CFR 2.48 - Revocation: Preliminary interview.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 1 2010-07-01 2010-07-01 false Revocation: Preliminary interview. 2.48....48 Revocation: Preliminary interview. (a) Interviewing officer. A parolee who is retaken on a warrant... violated his parole as charged, and if so, whether a revocation hearing should be conducted. The...

  12. 37 CFR 1.480 - Demand for international preliminary examination.

    Science.gov (United States)

    2010-07-01

    ... 37 Patents, Trademarks, and Copyrights 1 2010-07-01 2010-07-01 false Demand for international... Provisions International Preliminary Examination § 1.480 Demand for international preliminary examination. (a) On the filing of a proper Demand in an application for which the United States International...

  13. Preliminary Opto-Mechanical Design for the X2000 Transceiver

    Science.gov (United States)

    Hemmati, H.; Page, N. A.

    2000-01-01

    Preliminary optical design and mechanical conceptual design for a 30 cm aperture transceiver are described. A common aperture is used for both transmit and receive. Special attention was given to off-axis and scattered light rejection and isolation of the receive channel from the transmit channel. Requirements, details of the design and preliminary performance analysis of the transceiver are provided.

  14. Preliminary design package for Sunair SEC-601 solar collector

    Energy Technology Data Exchange (ETDEWEB)

    1978-12-01

    This report presents the preliminary design of the Owens-Illinois mode Sunair SEC-601 tubular air solar collector. Information in this package includes the Subsystem Design and Development Approaches, hazard analysis, and detailed drawings available as the Preliminary Design Review.

  15. Thermal structure of Venus upper atmosphere by a ground-to-thermosphere GCM: a preliminary study

    Science.gov (United States)

    Gilli, G.; Lebonnois, S.; Salmi, L.; Gonzalez-Galindo, F.; Lopez-Valverde, M. A.; Eymet, V.; Forget, F.

    2014-04-01

    We present here preliminary results of the thermal structure of the upper atmosphere of Venus simulated by a ground-to thermosphere General Circulation Model (GCM). The GCM developed at the Laboratoire de Meteorologie Dynamique (LMD) [1] has been recently improved and extended vertically from 100 to 150 km, with the inclusion of the physical processes which mostly contribute to the thermal balance in the mesosphere/thermosphere of Venus (i.e near IR heating by CO2, 15 μm thermal cooling, extreme UV heating, thermal conduction). We also focus on recent Venus Express and ground-based temperature measurements above 100 km, both at daytime and nighttime, and we interpret the observed main features with the help of model simulations. This ongoing study may indicate that both radiative and dynamical effects play a crucial role in determining the thermal structure of those upper layers of Venus atmosphere.

  16. Preliminary piping layout and integration of European test blanket modules subsystems in ITER CVCS area

    Energy Technology Data Exchange (ETDEWEB)

    Tarallo, Andrea, E-mail: andrea.tarallo@unina.it [CREATE, University of Naples Federico II, DII, P.le Tecchio, 80, 80125 Naples (Italy); Mozzillo, Rocco; Di Gironimo, Giuseppe [CREATE, University of Naples Federico II, DII, P.le Tecchio, 80, 80125 Naples (Italy); Aiello, Antonio; Utili, Marco [ENEA UTIS, C.R. Brasimone, Bacino del Brasimone, I-40032 Camugnano, BO (Italy); Ricapito, Italo [TBM& MD Project, Fusion for Energy, EU Commission, Carrer J. Pla, 2, Building B3, 08019 Barcelona (Spain)

    2015-04-15

    Highlights: • The use of human modeling tools for piping design in view of maintenance is discussed. • A possible preliminary layout for TBM subsystems in CVCS area has been designed with CATIA. • A DHM-based method to quickly check for maintainability of piping systems is suggested. - Abstract: This paper explores a possible integration of some ancillary systems of helium-cooled lithium lead (HCLL) and helium-cooled pebble-bed (HCPB) test blanket modules in ITER CVCS area. Computer-aided design and ergonomics simulation tools have been fundamental not only to define suitable routes for pipes, but also to quickly check for maintainability of equipment and in-line components. In particular, accessibility of equipment and systems has been investigated from the very first stages of the design using digital human models. In some cases, the digital simulations have resulted in changes in the initial space reservations.

  17. Preliminary modeling of the TMI-2 accident with MELPROG-TRAC

    Energy Technology Data Exchange (ETDEWEB)

    Jenks, R.P.

    1988-01-01

    In support of Nuclear Regulatory Commission and Organization for Economic Cooperation and Development (OECD)-sponsored Three Mile Island-Unit 2 (TMI-2) Analysis Exercise studies, work has been performed to develop a simulation model of the TMI-2 plant for use with the integrated MELPROG-TRAC computer code. Numerous nuclear power plant simulation studies have been performed with the TRAC computer code in the past. Some of these addressed the TMI-2 accident or other hypothetical events at the TMI plant. In addition, studies have been previously performed with the MELPROG-TRAC code using Oconee-1 and Surry plant models. This paper describes the preliminary MELPROG-TRAC input model for severe accident analysis.

  18. Thick Concrete Specimen Construction, Testing, and Preliminary Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Clayton, Dwight A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hoegh, Kyle [Univ. of Minnesota, Minneapolis, MN (United States); Khazanovich, Lev [Univ. of Minnesota, Minneapolis, MN (United States)

    2015-03-01

    The purpose of the U.S. Department of Energy Office of Nuclear Energy’s Light Water Reactor Sustainability (LWRS) Program is to develop technologies and other solutions that can improve the reliability, sustain the safety, and extend the operating lifetimes of nuclear power plants (NPPs) beyond 60 years. Since many important safety structures in an NPP are constructed of concrete, inspection techniques must be developed and tested to evaluate the internal condition. In-service containment structures generally do not allow for the destructive measures necessary to validate the accuracy of these inspection techniques. This creates a need for comparative testing of the various nondestructive evaluation (NDE) measurement techniques on concrete specimens with known material properties, voids, internal microstructure flaws, and reinforcement locations. A preliminary report detailed some of the challenges associated with thick reinforced concrete sections and prioritized conceptual designs of specimens that could be fabricated to represent NPP concrete structures for using in NDE evaluation comparisons. This led to the construction of the concrete specimen presented in this report, which has sufficient reinforcement density and cross-sectional size to represent an NPP containment wall. Details on how a suitably thick concrete specimen was constructed are presented, including the construction materials, final nominal design schematic, as well as formwork and rigging required to safely meet the desired dimensions of the concrete structure. The report also details the type and methods of forming the concrete specimen as well as information on how the rebar and simulated defects were embedded. Details on how the resulting specimen was transported, safely anchored, and marked to allow access for systematic comparative NDE testing of defects in a representative NPP containment wall concrete specimen are also given. Data collection using the MIRA Ultrasonic NDE equipment and

  19. 76 FR 39399 - Chlorpyrifos Registration Review; Preliminary Human Health Risk Assessment; Notice of Availability

    Science.gov (United States)

    2011-07-06

    ... AGENCY Chlorpyrifos Registration Review; Preliminary Human Health Risk Assessment; Notice of Availability... availability of EPA's preliminary human health risk assessment for the registration review of chlorpyrifos and... comprehensive preliminary human health risk assessment for all chlorpyrifos uses. After reviewing comments...

  20. 76 FR 52945 - Chlorpyrifos Registration Review; Preliminary Human Health Risk Assessment; Extension of Comment...

    Science.gov (United States)

    2011-08-24

    ... AGENCY Chlorpyrifos Registration Review; Preliminary Human Health Risk Assessment; Extension of Comment... availability of the chlorpyrifos registration review; preliminary human health risk assessment. This document... for the chlorpyrifos reregistration review, preliminary human health risk assessment, established in...

  1. Biologically Inspired Visual Model With Preliminary Cognition and Active Attention Adjustment.

    Science.gov (United States)

    Qiao, Hong; Xi, Xuanyang; Li, Yinlin; Wu, Wei; Li, Fengfu

    2015-11-01

    Recently, many computational models have been proposed to simulate visual cognition process. For example, the hierarchical Max-Pooling (HMAX) model was proposed according to the hierarchical and bottom-up structure of V1 to V4 in the ventral pathway of primate visual cortex, which could achieve position- and scale-tolerant recognition. In our previous work, we have introduced memory and association into the HMAX model to simulate visual cognition process. In this paper, we improve our theoretical framework by mimicking a more elaborate structure and function of the primate visual cortex. We will mainly focus on the new formation of memory and association in visual processing under different circumstances as well as preliminary cognition and active adjustment in the inferior temporal cortex, which are absent in the HMAX model. The main contributions of this paper are: 1) in the memory and association part, we apply deep convolutional neural networks to extract various episodic features of the objects since people use different features for object recognition. Moreover, to achieve a fast and robust recognition in the retrieval and association process, different types of features are stored in separated clusters and the feature binding of the same object is stimulated in a loop discharge manner and 2) in the preliminary cognition and active adjustment part, we introduce preliminary cognition to classify different types of objects since distinct neural circuits in a human brain are used for identification of various types of objects. Furthermore, active cognition adjustment of occlusion and orientation is implemented to the model to mimic the top-down effect in human cognition process. Finally, our model is evaluated on two face databases CAS-PEAL-R1 and AR. The results demonstrate that our model exhibits its efficiency on visual recognition process with much lower memory storage requirement and a better performance compared with the traditional purely computational

  2. Numerical Simulation of Wakes in a Weakly Stratified Fluid

    CERN Document Server

    Rottman, James W; Innis, George E; O'Shea, Thomas T; Novikov, Evgeny

    2014-01-01

    This paper describes some preliminary numerical studies using large eddy simulation of full-scale submarine wakes. Submarine wakes are a combination of the wake generated by a smooth slender body and a number of superimposed vortex pairs generated by various control surfaces and other body appendages. For this preliminary study, we attempt to gain some insight into the behavior of full-scale submarine wakes by computing separately the evolution the self-propelled wake of a slender body and the motion of a single vortex pair in both a non-stratified and a stratified environment. An important aspect of the simulations is the use of an iterative procedure to relax the initial turbulence field so that turbulent production and dissipation are in balance.

  3. Collaborative Simulation Grid: Multiscale Quantum-Mechanical/Classical Atomistic Simulations on Distributed PC Clusters in the US and Japan

    Science.gov (United States)

    Kikuchi, Hideaki; Kalia, Rajiv; Nakano, Aiichiro; Vashishta, Priya; Iyetomi, Hiroshi; Ogata, Shuji; Kouno, Takahisa; Shimojo, Fuyuki; Tsuruta, Kanji; Saini, Subhash; Biegel, Bryan (Technical Monitor)

    2002-01-01

    A multidisciplinary, collaborative simulation has been performed on a Grid of geographically distributed PC clusters. The multiscale simulation approach seamlessly combines i) atomistic simulation backed on the molecular dynamics (MD) method and ii) quantum mechanical (QM) calculation based on the density functional theory (DFT), so that accurate but less scalable computations are performed only where they are needed. The multiscale MD/QM simulation code has been Grid-enabled using i) a modular, additive hybridization scheme, ii) multiple QM clustering, and iii) computation/communication overlapping. The Gridified MD/QM simulation code has been used to study environmental effects of water molecules on fracture in silicon. A preliminary run of the code has achieved a parallel efficiency of 94% on 25 PCs distributed over 3 PC clusters in the US and Japan, and a larger test involving 154 processors on 5 distributed PC clusters is in progress.

  4. Preliminary Model of Porphyry Copper Deposits

    Science.gov (United States)

    Berger, Byron R.; Ayuso, Robert A.; Wynn, Jeffrey C.; Seal, Robert R., II

    2008-01-01

    The U.S. Geological Survey (USGS) Mineral Resources Program develops mineral-deposit models for application in USGS mineral-resource assessments and other mineral resource-related activities within the USGS as well as for nongovernmental applications. Periodic updates of models are published in order to incorporate new concepts and findings on the occurrence, nature, and origin of specific mineral deposit types. This update is a preliminary model of porphyry copper deposits that begins an update process of porphyry copper models published in USGS Bulletin 1693 in 1986. This update includes a greater variety of deposit attributes than were included in the 1986 model as well as more information about each attribute. It also includes an expanded discussion of geophysical and remote sensing attributes and tools useful in resource evaluations, a summary of current theoretical concepts of porphyry copper deposit genesis, and a summary of the environmental attributes of unmined and mined deposits.

  5. Repository Subsurface Preliminary Fire Hazard Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Richard C. Logan

    2001-07-30

    This fire hazard analysis identifies preliminary design and operations features, fire, and explosion hazards, and provides a reasonable basis to establish the design requirements of fire protection systems during development and emplacement phases of the subsurface repository. This document follows the Technical Work Plan (TWP) (CRWMS M&O 2001c) which was prepared in accordance with AP-2.21Q, ''Quality Determinations and Planning for Scientific, Engineering, and Regulatory Compliance Activities''; Attachment 4 of AP-ESH-008, ''Hazards Analysis System''; and AP-3.11Q, ''Technical Reports''. The objective of this report is to establish the requirements that provide for facility nuclear safety and a proper level of personnel safety and property protection from the effects of fire and the adverse effects of fire-extinguishing agents.

  6. Preliminary study of radium-contaminated soils

    Energy Technology Data Exchange (ETDEWEB)

    Healy, J.W.; Rodgers, J.C.

    1978-10-01

    A preliminary study was made of the potential radiation exposures to people from radium-226 contamination in the soil in order to provide guidance on limits to be applied in decontaminating land. Pathways included were inhalation of radium from resuspension; ingestion of radium with foods; external gamma radiation from radium daughters; inhalation of radon and daughter, both in the open air and in houses; and the intake of /sup 210/Pb and /sup 210/Po from both inhalation and ingestion. The depth of the contaminated layer is of importance for external exposure and especially for radon emanation. The most limiting pathway was found to be emanation of the radon into buildings with limiting values comparable to those found naturally in many areas.

  7. The Preliminaries of a Reference: Chain

    DEFF Research Database (Denmark)

    Butler, Graham; Sadl, Urska

    2016-01-01

    No decisive ruling was delivered by the Court of Justice of the European Union (hereafter: the Court) in Case C-189/14, Bogdan Chain v Atlanco Ltd. There is usually no case note worth writing without a judgment. However, the case in question came close to being concluded with a judgment, and the ......No decisive ruling was delivered by the Court of Justice of the European Union (hereafter: the Court) in Case C-189/14, Bogdan Chain v Atlanco Ltd. There is usually no case note worth writing without a judgment. However, the case in question came close to being concluded with a judgment......, and the reasons why no conclusive ruling was delivered is precisely what makes this case worth writing about. A preliminary reference was issued by a national court in Nicosia (Cyprus) following which at the Court, a reporting Judge and Advocate General were appointed. An oral hearing in the presence...

  8. CTF3 Design Report Preliminary Phase

    CERN Document Server

    Allard, D; Bernard, M; Bertuzzi, J P; Bienvenu, G; Bonzano, R; Bossart, Rudolf; Braun, H; Bravin, Enrico; Borburgh, J; Buttkus, J; Chazarenc, E; Chaput, R; Chohan, V; Cloye, J J; Corsini, R; Coudert, G; Damiani, M; Deghaye, S; Delahaye, J P; Di Maio, F; Dobers, T; Dubief, P; Dupuy, B; Durieu, L; Ferrari, A; Garvey, Terence; Geschonke, Günther; Hansen, J; Hellgren, H; Hourican, M; Lamidon, M; Le Duff, J; Lefèvre, T; Lewis, J H; Lindroos, J; Mahner, E; McMonagle, G; Monteiro, J; Mourier, J; Mouton, B; Odier, P; Otto, T; Pearce, P; Pittin, R; Poehler, M; Potier, J P; Raich, U; Rettig, M; Rinolfi, Louis; Risselada, Thys; Riva, R; Rossat, G; Royer, P; Sermeus, L; Setas, K; Simonet, G; Sladen, Jonathan P H; Søby, L; Tanner, L; Tecker, F A; Thomi, J C; Wilson, Ian H; Yvon, G

    2001-01-01

    The design of CLIC is based on a two-beam scheme, where the short pulses of high power 30 GHz RF are extracted from a drive beam running parallel to the main beam. The 3rd generation CLIC Test Facility (CTF3) will demonstrate the generation of the drive beam with the appropriate time structure, the extraction of 30 GHz RF power from this beam, as well as acceleration of a probe beam with 30 GHz RF cavities. The project makes maximum use of existing equipment and infrastructure of the LPI complex, which became available after the closure of LEP. In the first stage of the project, the "Preliminary Phase", the existing LIL linac and the EPA ring, both modified to suit the new requirements, are used to investigate the technique of frequency multiplication by means of interleaving bunches from subsequent trains. This report describes the design of this phase.

  9. Laryngeal electromyography in movement disorders: preliminary data

    Directory of Open Access Journals (Sweden)

    Kimaid Paulo A.T.

    2004-01-01

    Full Text Available This study describes preliminary laryngeal electromyography (LEMG data and botulinum toxin treatment in patients with dysphonia due to movement disorders. Twenty-five patients who had been clinically selected for botulinum toxin administration were examined, 19 with suspected laryngeal dystonia or spasmodic dysphonia (SD, 5 with vocal tremor, and 1 with Gilles de la Tourette syndrome (GTS. LEMG evaluations were performed before botulinum toxin administration using monopolar electrodes. Electromyography was consistent with dystonia in 14 patients and normal in 5, and differences in frequency suggesting essential tremor in 3 and Parkinson tremors in 2. The different LEMG patterns and significant improvement in our patients from botulinum toxin therapy has led us to perform laryngeal electromyography as a routine in UNICAMP movement disorders ambulatory.

  10. Lockheed Martin T-Rex: Preliminary report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-31

    T-Rex is a robot which may be used in toxic or flammable environments. The assessment of the T-Rex conducted at the Lockheed Martin facility was limited in its scope. The scope of the assessment was directed by the type of equipment being used and the amount of accessibility to the equipment. Due to severe time constraints--the assessment was conducted in one day--human factors interface activities were limited. This should be considered a preliminary assessment. This report covers aspects of the technology that were available to the assessment team. Recommendations for future evaluation of this technology are also included. The contents are as follows: Electrical Considerations; General Electrical Consideration; Trailing Cables; Grounding; Surface High Voltage Distribution; Low and Medium Voltage Alternating Current Circuits; Potential for Harmful Human Factor Incidents and Enterprise Disablement; Exclusion Zone Emergency Maintenance; and Recommendations.

  11. Preliminary Design of a Femtosecond Oscilloscope

    CERN Document Server

    Gazazyan, Edmond D; Kalantaryan, Davit K; Laziev, Edouard; Margaryan, Amour

    2005-01-01

    The calculations on motion of electrons in a finite length electromagnetic field of linearly and circularly polarized laser beams have shown that one can use the transversal deflection of electrons on a screen at a certain distance after the interaction region for the measurement of the length and longitudinal particle distribution of femtosecond bunches. In this work the construction and preliminary parameters of various parts of a device that may be called femtosecond oscilloscope are considered. The influence of various factors, such as the energy spread and size of the electron bunches, are taken into account. For CO2 laser intensity 1016 W/cm2 and field free drift length 1m the deflection is 5.3 and 0.06 cm, while the few centimeters long interaction length between 2 mirrors requires assembling accuracy 6 mm and 1.3 micron for 20 MeV to 50 keV, respectively.

  12. Helminthiases in Montes Claros. Preliminary survey

    Directory of Open Access Journals (Sweden)

    Rina Girard Kaminsky

    1976-04-01

    Full Text Available A preliminary survey was conducted for the presence of helminths in the city of Montes Claros, M. G., Brazil. Three groups of persons were examined by the direct smear, Kato thick film and MIFC techniques; one group by direct smear and Kato only. General findings were: a high prevalence of hookworm, followed by ascariasis, S. mansoni, S. stercoralis and very light infections with T. trichiurá. E. vermicularis and H. nana were ranking parasites at an orphanage, with some hookworm and S. mansoni infections as well. At a pig slaughter house, the dominant parasites were hookworm and S. mansoni. Pig cysticercosis was an incidental finding worth mentioning for the health hazard it represents for humans as well as an economic loss. From the comparative results between the Kato and the MIF the former proved itself again as a more sensitive and reliable concentration method for helminth eggs, of low cost and easy performance.

  13. Physalis: a New Method for Particle Simulations

    Science.gov (United States)

    Takagi, Shu; Oguz, Hasan; Prosperetti, Andrea

    2000-11-01

    A new computational method for the full Navier-Stokes viscous flow past cylinders and spheres is described and illustrated with preliminary results. Since, in the rest frame, the velocity vanishes on the particle, the Stokes equations apply in the immediate neighborhood of the surface. The analytic solutions of these equations available for both spheres and cylinders permit to effectively remove the particle, the effect of which is replaced by a consistency condition on the nodes of the computational grid that surround the particle. This condition is satisfied iteratively by a method that solves the field equations over the entire computational domain disregarding the presence of the particles, so that fast solvers can be used. The procedure eliminates the geometrical complexity of multi-particle simulations and permits to simulate disperse flows containing a large number of particles with a moderate computatonal cost. Supported by DOE and Japanese MESSC.

  14. A simulated Antarctic fast ice ecosystem

    Science.gov (United States)

    Arrigo, Kevin R.; Kremer, James N.; Sullivan, Cornelius W.

    1993-01-01

    A 2D numerical ecosystem model of Antarctic land fast ice is developed to elucidate the primary production with the Antarctic sea ice zone. The physical component employs atmospheric data to simulate congelation ice growth, initial brine entrapment, desalination, and nutrient flux. The biological component is based on the concept of a maximum temperature-dependent algal growth rate which is reduced by limitations imposed from insufficient light or nutrients, as well as suboptimal salinity. Preliminary simulations indicate that, during a bloom, microalgae are able to maintain their vertical position relative to the lower congelation ice margin and are not incorporated into the crystal matrix as the ice sheet thickens. It is inferred that land fast sea ice contains numerous microhabitats that are functionally distinct based upon the unique set of processes that control microalgal growth and accumulation within each.

  15. Simulation of various possible cementite structures

    Science.gov (United States)

    Titorov, D. B.

    2007-04-01

    The simulation of the cementite structure has been performed without resorting to any preliminary assumptions. The spheres simulating the Fe and C atoms are closely packed in accordance with the rules of pair interpenetration. The maximum depth of the interpenetration in the Fe-C pair was accepted to be intermediate between the maximum depths of the penetration in the Fe-Fe and C-C pairs in ferrite and diamond, respectively. Under such conditions, six iron atoms penetrate into a carbon atom. The carbon atom turns out to be located inside octahedra, which can be of various shapes, while the centers of iron atoms occupy the vertices of these octahedra. The translation of the octahedra leads to the formation of orthorhombic cementite structures with identical or close parameters, but with different relative positions of carbon and iron atoms.

  16. North Korean refugee doctors' preliminary examination scores

    Directory of Open Access Journals (Sweden)

    Sung Uk Chae

    2016-12-01

    Full Text Available Purpose Although there have been studies emphasizing the re-education of North Korean (NK doctors for post-unification of the Korean Peninsula, study on the content and scope of such re-education has yet to be conducted. Researchers intended to set the content and scope of re-education by a comparative analysis for the scores of the preliminary examination, which is comparable to the Korean Medical Licensing Examination (KMLE. Methods The scores of the first and second preliminary exams were analyzed by subject using the Wilcoxon signed rank test. The passing status of the group of NK doctors for KMLE in recent 3 years were investigated. The multiple-choice-question (MCQ items of which difficulty indexes of NK doctors were lower than those of South Korean (SK medical students by two times of the standard deviation of the scores of SK medical students were selected to investigate the relevant reasons. Results The average scores of nearly all subjects were improved in the second exam compared with the first exam. The passing rate of the group of NK doctors was 75%. The number of MCQ items of which difficulty indexes of NK doctors were lower than those of SK medical students was 51 (6.38%. NK doctors’ lack of understandings for Diagnostic Techniques and Procedures, Therapeutics, Prenatal Care, and Managed Care Programs was suggested as the possible reason. Conclusion The education of integrated courses focusing on Diagnostic Techniques and Procedures and Therapeutics, and apprenticeship-style training for clinical practice of core subjects are needed. Special lectures on the Preventive Medicine are likely to be required also.

  17. Preliminary dose assessment of the Chernobyl accident

    Energy Technology Data Exchange (ETDEWEB)

    Hull, A.P.

    1987-01-01

    From the major accident at Unit 4 of the Chernobyl nuclear power station, a plume of airborne radioactive fission products was initially carried northwesterly toward Poland, thence toward Scandinavia and into Central Europe. Reports of the levels of radioactivity in a variety of media and of external radiation levels were collected in the Department of Energy's Emergency Operations Center and compiled into a data bank. Portions of these and other data which were obtained directly from published and official reports were utilized to make a preliminary assessment of the extent and magnitude of the external dose to individuals downwind from Chernobyl. Radioactive /sup 131/I was the predominant fission product. The time of arrival of the plume and the maximum concentrations of /sup 131/I in air, vegetation and milk and the maximum reported depositions and external radiation levels have been tabulated country by country. A large amount of the total activity in the release was apparently carried to a significant elevation. The data suggest that in areas where rainfall occurred, deposition levels were from ten to one-hundred times those observed in nearby ''dry'' locations. Sufficient spectral data were obtained to establish average release fractions and to establish a reference spectra of the other nuclides in the release. Preliminary calculations indicated that the collective dose equivalent to the population in Scandinavia and Central Europe during the first year after the Chernobyl accident would be about 8 x 10/sup 6/ person-rem. From the Soviet report, it appears that a first year population dose of about 2 x 10/sup 7/ person-rem (2 x 10/sup 5/ Sv) will be received by the population who were downwind of Chernobyl within the U.S.S.R. during the accident and its subsequent releases over the following week. 32 refs., 14 figs., 20 tabs.

  18. Preliminary Considerations on the Thermodynamic Feasibility and Possible Design of Ultra-, Micro- and Nano-Gas Turbines

    Directory of Open Access Journals (Sweden)

    Enrico Sciubba

    2006-06-01

    Full Text Available The paper describes a preliminary feasibility analysis of a nano-GT (50÷200 W for portable power generation. The system is examined under both a thermodynamic and an operative point of view. The technical problems posed by a practical implementation of an operative system are assessed first via a preliminary calculation of the overall thermodynamic performance of the real cycle, and then via a first-order design of the main components. The extremely small size of the device makes a preliminary estimate of the components performance problematic (the available data are scant and unreliable: it is likely that a real advance in this field must go through a series of detailed fluid-dynamic simulations. The results of our preliminary sizing are compared with the existing technical literature in an attempt to further define the material selection, in view of a possible prototype production. Some considerations are also offered about the final utilisation of nano-GTs: in our opinion, they represent a realistic alternative to batteries for powering optical, GPS and other satellite devices, or in medical applications.

  19. Cosmological simulations using a static scalar-tensor theory

    Energy Technology Data Exchange (ETDEWEB)

    RodrIguez-Meza, M A [Depto. de Fisica, Instituto Nacional de Investigaciones Nucleares, Col. Escandon, Apdo. Postal 18-1027, 11801 Mexico D.F (Mexico); Gonzalez-Morales, A X [Departamento Ingenierias, Universidad Iberoamericana, Prol. Paseo de la Reforma 880 Lomas de Santa Fe, Mexico D.F. Mexico (Mexico); Gabbasov, R F [Depto. de Fisica, Instituto Nacional de Investigaciones Nucleares, Col. Escandon, Apdo. Postal 18-1027, 11801 Mexico D.F (Mexico); Cervantes-Cota, Jorge L [Depto. de Fisica, Instituto Nacional de Investigaciones Nucleares, Col. Escandon, Apdo. Postal 18-1027, 11801 Mexico D.F (Mexico)

    2007-11-15

    We present {lambda}CDM N-body cosmological simulations in the framework of of a static general scalar-tensor theory of gravity. Due to the influence of the non-minimally coupled scalar field, the gravitational potential is modified by a Yukawa type term, yielding a new structure formation dynamics. We present some preliminary results and, in particular, we compute the density and velocity profiles of the most massive group.

  20. Validation of Compton Scattering Monte Carlo Simulation Models

    CERN Document Server

    Weidenspointner, Georg; Hauf, Steffen; Hoff, Gabriela; Kuster, Markus; Pia, Maria Grazia; Saracco, Paolo

    2014-01-01

    Several models for the Monte Carlo simulation of Compton scattering on electrons are quantitatively evaluated with respect to a large collection of experimental data retrieved from the literature. Some of these models are currently implemented in general purpose Monte Carlo systems; some have been implemented and evaluated for possible use in Monte Carlo particle transport for the first time in this study. Here we present first and preliminary results concerning total and differential Compton scattering cross sections.

  1. Manned Flight Simulator (MFS)

    Data.gov (United States)

    Federal Laboratory Consortium — The Aircraft Simulation Division, home to the Manned Flight Simulator (MFS), provides real-time, high fidelity, hardware-in-the-loop flight simulation capabilities...

  2. Platform for dynamic tests: preliminary studies, design and construction

    Directory of Open Access Journals (Sweden)

    J. E. Campuzano

    Full Text Available This paper is about the design and construction of a platform for dynamic tests especially with people jumping, walking, etc. Initially it was tried to find out projects already implemented in platforms and dynamic tests and to study the loads produced by movement of people on slabs and the structural response to these loads. The limits established by different standards have been also studied for these dynamic responses, taking into account the ultimate limit state, as well as the structure in service, since the human body is very sensitive to structural vibrations. Parametric studies were performed considering various configurations of slabs (different spans, thicknesses and conditions of support have been done, looking for a configuration that could have natural frequency close to the frequencies of the human loads. The slab should have dimensions compatible with the available physical space, fundamental frequency below 5 Hz and maximum immediate deflection compatible with the indications of the Brazilian standard NBR6118: 2007. Based on these criteria was chosen a rectangular structure consists of a solid reinforced concrete rectangular slab studded in two opposite edges of steel beams with shear connectors type U. The other two edges are free. The steel beams supporting the slab, in turn, are supported on eight metal profiles (two in each corner of the slab that are supported on two to two short columns of steel profile H. Profiles U in steel are welded to four columns, forming a horizontal frame. Numerical analysis of the dynamic test platform have been performed for free and forced vibration, for obtaining the natural frequencies and corresponding vibration modes, considering the self-weight of the structure and the load that simulates people's weight. After obtaining a structural configuration that fulfilled the stipulated requirements, the design of the slab taking into account the recommendations of the Brazilian standard NBR6118: 2007

  3. A Preliminary Feasibility Study On Seismic Monitoring Of Polymer Flooding

    Science.gov (United States)

    Nguyen, P. K.; Park, C.; Lim, B.; Nam, M.

    2012-12-01

    Polymer flooding using water with soluble polymers is an enhanced oil recovery technique, which intends to maximize oil-recovery sweep efficiency by minimizing fingering effects and as a result creating a smooth flood front; polymer flooding decreases the flow rates within high permeability zone while enhances those of lower permeabilities. Understanding of fluid fronts and saturations is critical to not only optimizing polymer flooding but also monitoring the efficiency. Polymer flooding monitoring can be made in single well scale with high-resolution wireline logging, in inter-well scale with tomography, and in reservoir scale with surface survey. For reservoir scale monitoring, this study makes a preliminary feasibility study based on constructing rock physics models (RPMs), which can bridge variations in reservoir parameters to the changes in seismic responses. For constructing RPMs, we change reservoir parameters with consideration of polymer flooding to a reservoir. Time-lapse seismic data for corresponding RPMs are simulated using a time-domain staggered-finite-difference modeling with implementation of a boundary condition of conventional perfect match layer. Analysis on time-lapse seismic data with respect to the changes in fluid front and saturation can give an insight on feasibility of surface seismic survey to polymer flooding. Acknowledgements: This work was supported by the Energy Efficiency & Resources of the Korea Institute of Energy Technology Evaluation and Planning (KETEP) grant funded by the Korea government Ministry of Knowledge Economy (No. 2012T100201588). Myung Jin Nam was partially supported by the National Research Foundation of Korea(NRF) grant funded by the Korea government(MEST) (No. 2011-0014684).

  4. Advanced Simulation Center

    Data.gov (United States)

    Federal Laboratory Consortium — The Advanced Simulation Center consists of 10 individual facilities which provide missile and submunition hardware-in-the-loop simulation capabilities. The following...

  5. NSLS-II Preliminary Design Report

    Energy Technology Data Exchange (ETDEWEB)

    Dierker, S.

    2007-11-01

    Following the CD0 approval of the National Synchrotron Light Source II (NSLS-II) during August 2005, Brookhaven National Laboratory prepared a conceptual design for a worldclass user facility for scientific research using synchrotron radiation. DOE SC review of the preliminary baseline in December 2006 led to the subsequent CD1 approval (approval of alternative selection and cost range). This report is the documentation of the preliminary design work for the NSLS-II facility. The preliminary design of the Accelerator Systems (Part 1) was developed mostly based of the Conceptual Design Report, except for the Booster design, which was changed from in-storage-ring tunnel configuration to in external- tunnel configuration. The design of beamlines (Part 2) is based on designs developed by engineering firms in accordance with the specification provided by the Project. The conventional facility design (Part 3) is the Title 1 preliminary design by the AE firm that met the NSLS-II requirements. Last and very important, Part 4 documents the ES&H design and considerations related to this preliminary design. The NSLS-II performance goals are motivated by the recognition that major advances in many important technology problems will require scientific breakthroughs in developing new materials with advanced properties. Achieving this will require the development of new tools that will enable the characterization of the atomic and electronic structure, chemical composition, and magnetic properties of materials, at nanoscale resolution. These tools must be nondestructive, to image and characterize buried structures and interfaces, and they must operate in a wide range of temperatures and harsh environments. The NSLS-II facility will provide ultra high brightness and flux and exceptional beam stability. It will also provide advanced insertion devices, optics, detectors, and robotics, and a suite of scientific instruments designed to maximize the scientific output of the facility

  6. NSLS-II Preliminary Design Report

    Energy Technology Data Exchange (ETDEWEB)

    Dierker, S.

    2007-11-01

    Following the CD0 approval of the National Synchrotron Light Source II (NSLS-II) during August 2005, Brookhaven National Laboratory prepared a conceptual design for a worldclass user facility for scientific research using synchrotron radiation. DOE SC review of the preliminary baseline in December 2006 led to the subsequent CD1 approval (approval of alternative selection and cost range). This report is the documentation of the preliminary design work for the NSLS-II facility. The preliminary design of the Accelerator Systems (Part 1) was developed mostly based of the Conceptual Design Report, except for the Booster design, which was changed from in-storage-ring tunnel configuration to in external- tunnel configuration. The design of beamlines (Part 2) is based on designs developed by engineering firms in accordance with the specification provided by the Project. The conventional facility design (Part 3) is the Title 1 preliminary design by the AE firm that met the NSLS-II requirements. Last and very important, Part 4 documents the ES&H design and considerations related to this preliminary design. The NSLS-II performance goals are motivated by the recognition that major advances in many important technology problems will require scientific breakthroughs in developing new materials with advanced properties. Achieving this will require the development of new tools that will enable the characterization of the atomic and electronic structure, chemical composition, and magnetic properties of materials, at nanoscale resolution. These tools must be nondestructive, to image and characterize buried structures and interfaces, and they must operate in a wide range of temperatures and harsh environments. The NSLS-II facility will provide ultra high brightness and flux and exceptional beam stability. It will also provide advanced insertion devices, optics, detectors, and robotics, and a suite of scientific instruments designed to maximize the scientific output of the facility

  7. Structural considerations for a software life cycle dynamic simulation model

    Science.gov (United States)

    Tausworthe, R. C.; Mckenzie, M.; Lin, C. Y.

    1983-01-01

    This paper presents the results of a preliminary study into the prospects for simulating the software implementation and maintenance life cycle process, with the aim of producing a computerized tool for use by management and software engineering personnel in project planning, tradeoff studies involving product, environmental, situational, and technological factors, and training. The approach taken is the modular application of a 'flow of resource' concept to the systems dynamics simulation modeling technique. The software life cycle process is represented as a number of stochastic, time-varying, interacting work tasks that each achieves one of the project milestones. Each task is characterized by the item produced, the personnel applied, and the budgetary profile.

  8. An Integrated Approach for Entry Mission Design and Flight Simulations

    Science.gov (United States)

    Lu, Ping; Rao, Prabhakara

    2004-01-01

    An integrated approach for entry trajectory design, guidance, and simulation is proposed. The key ingredients for this approach are an on-line 3 degree-of-freedom entry trajectory planning algorithm and the entry guidance algorithm that generates the guidance gains automatically. When fully developed, such a tool could enable end-bend entry mission design and simulations in 3DOF and 6DOF mode from de-orbit burn to the TAEM interface and beyond, all in one key stroke. Some preliminary examples of such a capability are presented in this paper that demonstrate the potential of this type of integrated environment.

  9. An attempt toward the generalized Langevin dynamics simulation

    Directory of Open Access Journals (Sweden)

    B.Kim

    2008-03-01

    Full Text Available An attempt to generalize the Langevin dynamics simulation method is presented based on the generalized Langevin theory of liquids, in which the dynamics of both solute and solvent is treated by the generalized Langevin equations, but the integration of the equation of motion of solute is made in the manner similar to the ordinary molecular dynamics simulation with discretized time steps along a trajectory. A preliminary result is derived based on an assumption of the uniform solvent density. The result is regarded to be a microscopic generalization of the phenomenological Langevin theory for the harmonic oscillator immersed in a continuum solvent developed by Wang and Uhlenbeck.

  10. Best practice strategies for validation of micro moulding process simulation

    DEFF Research Database (Denmark)

    Costa, Franco; Tosello, Guido; Whiteside, Ben

    2009-01-01

    be easily controlled or known by the simulation analyst and others which are not easily known. For this reason, experimental validation studies are an important tool for establishing best practice methodologies for use during analysis set up on all future design projects. During the validation studies......, detailed information about the moulding process is gathered and used to establish these methodologies. Whereas in routine design projects, these methodologies are then relied on to provide efficient but reliable working practices. Data analysis and simulations on preliminary micro-moulding experiments have...

  11. Best practice strategies for validation of micro moulding process simulation

    DEFF Research Database (Denmark)

    Costa, Franco; Tosello, Guido; Whiteside, Ben

    2009-01-01

    be easily controlled or known by the simulation analyst and others which are not easily known. For this reason, experimental validation studies are an important tool for establishing best practice methodologies for use during analysis set up on all future design projects. During the validation studies......, detailed information about the moulding process is gathered and used to establish these methodologies. Whereas in routine design projects, these methodologies are then relied on to provide efficient but reliable working practices. Data analysis and simulations on preliminary micro-moulding experiments have...

  12. Hybrid and electric advanced vehicle systems (heavy) simulation

    Science.gov (United States)

    Hammond, R. A.; Mcgehee, R. K.

    1981-01-01

    A computer program to simulate hybrid and electric advanced vehicle systems (HEAVY) is described. It is intended for use early in the design process: concept evaluation, alternative comparison, preliminary design, control and management strategy development, component sizing, and sensitivity studies. It allows the designer to quickly, conveniently, and economically predict the performance of a proposed drive train. The user defines the system to be simulated using a library of predefined component models that may be connected to represent a wide variety of propulsion systems. The development of three models are discussed as examples.

  13. A Preliminary Tsunami vulnerability analysis for Bakirkoy district in Istanbul

    Science.gov (United States)

    Tufekci, Duygu; Lutfi Suzen, M.; Cevdet Yalciner, Ahmet; Zaytsev, Andrey

    2016-04-01

    Resilience of coastal utilities after earthquakes and tsunamis has major importance for efficient and proper rescue and recovery operations soon after the disasters. Vulnerability assessment of coastal areas under extreme events has major importance for preparedness and development of mitigation strategies. The Sea of Marmara has experienced numerous earthquakes as well as associated tsunamis. There are variety of coastal facilities such as ports, small craft harbors, and terminals for maritime transportation, water front roads and business centers mainly at North Coast of Marmara Sea in megacity Istanbul. A detailed vulnerability analysis for Yenikapi region and a detailed resilience analysis for Haydarpasa port in Istanbul have been studied in previously by Cankaya et al., (2015) and Aytore et al., (2015) in SATREPS project. In this study, the methodology of vulnerability analysis under tsunami attack given in Cankaya et al., (2015) is modified and applied to Bakirkoy district of Istanbul. Bakirkoy district is located at western part of Istanbul and faces to the North Coast of Marmara Sea from 28.77oE to 28.89oE. High resolution spatial dataset of Istanbul Metropolitan Municipality (IMM) is used and analyzed. The bathymetry and topography database and the spatial dataset containing all buildings/structures/infrastructures in the district are collated and utilized for tsunami numerical modeling and following vulnerability analysis. The tsunami parameters from deterministically defined worst case scenarios are computed from the simulations using tsunami numerical model NAMI DANCE. The vulnerability assessment parameters in the district according to vulnerability and resilience are defined; and scored by implementation of a GIS based TVA with appropriate MCDA methods. The risk level is computed using tsunami intensity (level of flow depth from simulations) and TVA results at every location in Bakirkoy district. The preliminary results are presented and discussed

  14. Preliminary results of steel containment vessel model test

    Energy Technology Data Exchange (ETDEWEB)

    Luk, V.K.; Hessheimer, M.F. [Sandia National Labs., Albuquerque, NM (United States); Matsumoto, T.; Komine, K.; Arai, S. [Nuclear Power Engineering Corp., Tokyo (Japan); Costello, J.F. [Nuclear Regulatory Commission, Washington, DC (United States)

    1998-04-01

    A high pressure test of a mixed-scaled model (1:10 in geometry and 1:4 in shell thickness) of a steel containment vessel (SCV), representing an improved boiling water reactor (BWR) Mark II containment, was conducted on December 11--12, 1996 at Sandia National Laboratories. This paper describes the preliminary results of the high pressure test. In addition, the preliminary post-test measurement data and the preliminary comparison of test data with pretest analysis predictions are also presented.

  15. Molecular Simulation of Nonequilibrium Hypersonic Flows

    Science.gov (United States)

    Schwartzentruber, T. E.; Valentini, P.; Tump, P.

    2011-08-01

    Large-scale conventional time-driven molecular dynam- ics (MD) simulations of normal shock waves are performed for monatomic argon and argon-helium mixtures. For pure argon, near perfect agreement between MD and direct simulation Monte Carlo (DSMC) results using the variable-hard-sphere model are found for density and temperature profiles as well as for velocity distribution functions throughout the shock. MD simulation results for argon are also in excellent agreement with experimental shock thickness data. Preliminary MD simulation results for argon-helium mixtures are in qualitative agreement with experimental density and temperature profile data, where separation between argon and helium density profiles due to disparate atomic mass is observed. Since conventional time-driven MD simulation of di- lute gases is computationally inefficient, a combined Event-Driven/Time-Driven MD algorithm is presented. The ED/TD-MD algorithm computes impending collisions and advances molecules directly to their next collision while evaluating the collision using conventional time-driven MD with an arbitrary interatomic potential. The method timestep thus approaches the mean-collision- time in the gas, while also detecting and simulating multi- body collisions with a small approximation. Extension of the method to diatomic and small polyatomic molecules is detailed, where center-of-mass velocities and extended cutoff radii are used to advance molecules to impending collisions. Only atomic positions are integrated during collisions and molecule sorting algorithms are employed to determine if atoms are bound in a molecule after a collision event. Rotational relaxation to equilibrium for a low density diatomic gas is validated by comparison with large-scale conventional time-driven MD simulation, where the final rotational distribution function is verified to be the correct Boltzmann rotational energy distribution.

  16. Preliminary Framework for Human-Automation Collaboration

    Energy Technology Data Exchange (ETDEWEB)

    Oxstrand, Johanna Helene [Idaho National Lab. (INL), Idaho Falls, ID (United States); Le Blanc, Katya Lee [Idaho National Lab. (INL), Idaho Falls, ID (United States); Spielman, Zachary Alexander [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-09-01

    The Department of Energy’s Advanced Reactor Technologies Program sponsors research, development and deployment activities through its Next Generation Nuclear Plant, Advanced Reactor Concepts, and Advanced Small Modular Reactor (aSMR) Programs to promote safety, technical, economical, and environmental advancements of innovative Generation IV nuclear energy technologies. The Human Automation Collaboration (HAC) Research Project is located under the aSMR Program, which identifies developing advanced instrumentation and controls and human-machine interfaces as one of four key research areas. It is expected that the new nuclear power plant designs will employ technology significantly more advanced than the analog systems in the existing reactor fleet as well as utilizing automation to a greater extent. Moving towards more advanced technology and more automation does not necessary imply more efficient and safer operation of the plant. Instead, a number of concerns about how these technologies will affect human performance and the overall safety of the plant need to be addressed. More specifically, it is important to investigate how the operator and the automation work as a team to ensure effective and safe plant operation, also known as the human-automation collaboration (HAC). The focus of the HAC research is to understand how various characteristics of automation (such as its reliability, processes, and modes) effect an operator’s use and awareness of plant conditions. In other words, the research team investigates how to best design the collaboration between the operators and the automated systems in a manner that has the greatest positive impact on overall plant performance and reliability. This report addresses the Department of Energy milestone M4AT-15IN2302054, Complete Preliminary Framework for Human-Automation Collaboration, by discussing the two phased development of a preliminary HAC framework. The framework developed in the first phase was used as the

  17. Astor Pass Seismic Surveys Preliminary Report

    Energy Technology Data Exchange (ETDEWEB)

    Louie, John [UNR; Pullammanappallil, Satish [Optim; Faulds, James; Eisses, Amy; Kell, Annie; Frary, Roxanna; Kent, Graham

    2011-08-05

    In collaboration with the Pyramid Lake Paiute Tribe (PLPT), the University of Nevada, Reno (UNR) and Optim re-processed, or collected and processed, over 24 miles of 2d seismic-reflection data near the northwest corner of Pyramid Lake, Nevada. The network of 2d land surveys achieved a near-3d density at the Astor Pass geothermal prospect that the PLPT drilled during Nov. 2010 to Feb. 2011. The Bureau of Indian Affairs funded additional seismic work around the Lake, and an extensive, detailed single-channel marine survey producing more than 300 miles of section, imaging more than 120 ft below the Lake bottom. Optim’s land data collection utilized multiple heavy vibrators and recorded over 200 channels live, providing a state-of-the-art reflection-refraction data set. After advanced seismic analysis including first-arrival velocity optimization and prestack depth migration, the 2d sections show clear fault-plane reflections, in some areas as deep as 4000 ft, tying to distinct terminations of the mostly volcanic stratigraphy. Some lines achieved velocity control to 3000 ft depth; all lines show reflections and terminations to 5000 ft depth. Three separate sets of normal faults appear in an initial interpretation of fault reflections and stratigraphic terminations, after loading the data into the OpendTect 3d seismic visualization system. Each preliminary fault set includes a continuous trace more than 3000 ft long, and a swarm of short fault strands. The three preliminary normal-fault sets strike northerly with westward dip, northwesterly with northeast dip, and easterly with north dip. An intersection of all three fault systems documented in the seismic sections at the end of Phase I helped to locate the APS-2 and APS-3 slimholes. The seismic sections do not show the faults connected to the Astor Pass tufa spire, suggesting that we have imaged mostly Tertiary-aged faults. We hypothesize that the Recent, active faults that produced the tufa through hotspring

  18. Preliminary Study of Single-Phase Natural Circulation for Lab-scaled Molten Salt Application

    Energy Technology Data Exchange (ETDEWEB)

    Shin, Yukyung; Kang, Sarah; Kim, In Guk; Seo, Seok Bin; Bang, In Cheol [UNIST, Ulsan (Korea, Republic of); Park, Seong Dae [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    Advanced reactors such as MSR (FHR), VHTR and AHTR utilized molten salt as a coolant for efficiency and safety which has advantages in higher heat capacity, lower pumping power and scale compared to liquid metal. It becomes more necessary to study on the characteristics of molten salt. However, due to several characteristics such as high operating temperature, large-scale facility and preventing solidification, satisfying that condition for study has difficulties. Thus simulant fluid was used with scaling method for lab-scale experiment. Scaled experiment enables simulant fluid to simulate fluid mechanics and heat transfer behavior of molten salt on lower operating temperature and reduced scale. In this paper, as a proof test of the scaled experiment, simplified single-phase natural circulation loop was designed in a lab-scale and applied to the passive safety system in advanced reactor in which molten salt is considered as a major coolant of the system. For the application of the improved safety system, prototype was based on the primary loop of the test-scale DRACS, the main passive safety system in FHR, developed at the OSU. For preliminary experiment, single-phase natural circulation under low power was performed. DOWTHERM A and DOWTHERM RP were selected as simulant candidates. Then, study of feasibility with simulant was conducted based on the scaling law for heat transfer characteristics and geometric parameters. Additionally, simulation with MARS code and ANSYS-CFX with the same condition of natural circulation was carried out as verification. For the accurate code simulation, thermo-physical properties of DOWTHERM A and RP were developed and implemented into MARS code. In this study, single-phase natural circulation experiment was performed with simulant oil, DOWTHERM RP, based on the passive safety system of FHR. Feasibility of similarity experiment for molten salt with oil simulant was confirmed by scaling method. In addition, simulation with two

  19. Experimental interstellar organic chemistry - Preliminary findings

    Science.gov (United States)

    Khare, B. N.; Sagan, C.

    1973-01-01

    Review of the results of some explicit experimental simulation of interstellar organic chemistry consisting in low-temperature high-vacuum UV irradiation of condensed simple gases known or suspected to be present in the interstellar medium. The results include the finding that acetonitrile may be present in the interstellar medium. The implication of this and other findings are discussed.

  20. Experimental interstellar organic chemistry - Preliminary findings

    Science.gov (United States)

    Khare, B. N.; Sagan, C.

    1973-01-01

    Review of the results of some explicit experimental simulation of interstellar organic chemistry consisting in low-temperature high-vacuum UV irradiation of condensed simple gases known or suspected to be present in the interstellar medium. The results include the finding that acetonitrile may be present in the interstellar medium. The implication of this and other findings are discussed.

  1. Analysis of rainfall-induced shallow landslides in Jamne and Jaszcze stream valleys (Polish Carpathians – preliminary results

    Directory of Open Access Journals (Sweden)

    Zydroń Tymoteusz

    2016-03-01

    Full Text Available Analysis of rainfall-induced shallow landslides in Jamne and Jaszcze stream valleys (Polish Carpathians - preliminary results. Preliminary shallow landslide susceptibility mapping of the Jamne and Jaszcze stream valleys, located in the Polish Flysch Carpathians, is presented in the paper. For the purpose of mapping, there were used SINMAP and Iverson’s models integrating infiltration and slope stability calculations. The calibration of the used models parameters, obtained from limited field and laboratory tests, was performed using data from 8-9 July 1997, when as a consequence of a very intense rainfall, 94 shallow landslides were observed on meadows and arable lands. A comparison of the slope stability calculation results and the localisation of the noticed shallow landslides showed satisfactory agreement between localisation of the observed and computed unstable areas. However, it was concluded that better simulation results were obtained using Iverson’s model.

  2. Plans and Preliminary Results of Fundamental Studies of Ice Crystal Icing Physics in the NASA Propulsion Systems Laboratory

    Science.gov (United States)

    Struk, Peter; Tsao, Jen-Ching; Bartkus, Tadas

    2017-01-01

    This paper describes plans and preliminary results for using the NASA Propulsion Systems Lab (PSL) to experimentally study the fundamental physics of ice-crystal ice accretion. NASA is evaluating whether this facility, in addition to full-engine and motor-driven-rig tests, can be used for more fundamental ice-accretion studies that simulate the different mixed-phase icing conditions along the core flow passage of a turbo-fan engine compressor. The data from such fundamental accretion tests will be used to help develop and validate models of the accretion process. This paper presents data from some preliminary testing performed in May 2015 which examined how a mixed-phase cloud could be generated at PSL using evaporative cooling in a warmer-than-freezing environment.

  3. Interfacing VPSC with finite element codes. Demonstration of irradiation growth simulation in a cladding tube

    Energy Technology Data Exchange (ETDEWEB)

    Patra, Anirban [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Tome, Carlos [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-03-23

    This Milestone report shows good progress in interfacing VPSC with the FE codes ABAQUS and MOOSE, to perform component-level simulations of irradiation-induced deformation in Zirconium alloys. In this preliminary application, we have performed an irradiation growth simulation in the quarter geometry of a cladding tube. We have benchmarked VPSC-ABAQUS and VPSC-MOOSE predictions with VPSC-SA predictions to verify the accuracy of the VPSCFE interface. Predictions from the FE simulations are in general agreement with VPSC-SA simulations and also with experimental trends.

  4. Experience with Large Scale Simulations on the EGEE Grid for the AUGER collaboration

    Energy Technology Data Exchange (ETDEWEB)

    Schovancova, J.; Chudoba, J.; Dvorak, F.; Filipovic, J.; Kmunicek, J.; Krenek, A.; Matyska, L.; Mulac, M.; Ruda, M.; Salvet, Z.; Sitera, J.; Sustr, Z.; Travnicek, P.

    2007-07-01

    We share our experience with the Large Scale Monte Carlo Simulations using the CORSIKA simulation program performed by the VO AUGER users on the EGEE Grid environment. We report on the AUGER CPU Challenge performed in April 2007 as a test of availability of the VO AUGER dedicated resources. We developed a set of scripts for an easy handling of a Large Scale Simulations by a very small number of users. We show status of the AUGER Offline Production ran with the CORSIKA simulation program, where these scripts were used. We report our preliminary results with testing the Job Provenance as the long-term information storage. (Author)

  5. Tsunami hazard assessment at Port Alberni, BC, Canada: preliminary model results

    Science.gov (United States)

    Grilli, S. T.; Insua, T. L.; Grilli, A. R.; Douglas, K. L.; Shelby, M. R.; Wang, K.; Gao, D.

    2016-12-01

    Located in the heart of Vancouver Island, BC, Port Alberni has a well-known history of tsunamis. Many of the Nuu-Chah-Nulth First Nations share oral stories about a strong fight between a thunderbird and a whale that caused big waves in a winter night, a story that is compatible with the recently recognized great Cascadia tsunami in January, 1700. Port Alberni, with a total population of approximately 20,000 people, lies beside the Somass River, at the very end of Barkley Sound Inlet. The narrow canal connecting this town to the Pacific Ocean runs for more than 64 km ( 40 miles) between steep mountains, providing an ideal setting for the amplification of tsunami waves through funnelling effects. The devastating effects of tsunamis are still fresh in residents' memories from the impact of the 1964 Alaska tsunami that caused serious damage to the city. In June 2016, Emergency Management BC ran a coastal exercise in Port Alberni, simulating the response to an earthquake and a tsunami. During three days, the emergency teams in the City of Port Alberni practiced and learned from the experience. Ocean Networks Canada contributed to this exercise with the development of preliminary simulations of tsunami impact on the city from a buried rupture of the Cascadia Subduction Zone, including the Explorer segment. Wave propagation was simulated with the long-wave model FUNWAVE-TVD. Preliminary results indicate a strong amplification of tsunami waves in the Port Alberni area. The inundation zone in Port Alberni had a footprint similar to that of the 1700 Cascadia and 1964 Alaska tsunamis, inundating the area surrounding the Somass river and preferentially following the Kitsuksis and Roger Creek river margins into the city. Several other tsunami source scenarios, including splay faulting and trench-breaching ruptures are currently being modeled for the city of Port Alberni following a similar approach. These results will be presented at the conference.

  6. Comparing three methods for participatory simulation of hospital work systems

    DEFF Research Database (Denmark)

    Broberg, Ole

    addressed different elements of a hospital work system. Problem statement: Different methods for simulating the future work system for healthcare professionals have been applied in a number of green field and renovation design projects of hospitals in Denmark. The methods differed in the type of simulation...... objects representing the work system. Hence, this was an opportunity to study if these differences influenced which elements of a work system were in focus when healthcare professionals simulated and evaluated future work. Preliminary observations indicated this was the case but it was not understood how...... on how to organize the work in different spatial layouts. In addition to the object attributes other factors may play a role in what work system elements are being addressed. An important one seems to be at which point in the hospital design process the simulation is carried out. Conclusions: Different...

  7. Biologically-inspired hexapod robot design and simulation

    Science.gov (United States)

    Espenschied, Kenneth S.; Quinn, Roger D.

    1994-01-01

    The design and construction of a biologically-inspired hexapod robot is presented. A previously developed simulation is modified to include models of the DC drive motors, the motor driver circuits and their transmissions. The application of this simulation to the design and development of the robot is discussed. The mechanisms thought to be responsible for the leg coordination of the walking stick insect were previously applied to control the straight-line locomotion of a robot. We generalized these rules for a robot walking on a plane. This biologically-inspired control strategy is used to control the robot in simulation. Numerical results show that the general body motion and performance of the simulated robot is similar to that of the robot based on our preliminary experimental results.

  8. COCOA: Simulating Observations of Star Cluster Simulations

    Science.gov (United States)

    Askar, Abbas; Giersz, Mirek; Pych, Wojciech; Dalessandro, Emanuele

    2017-03-01

    COCOA (Cluster simulatiOn Comparison with ObservAtions) creates idealized mock photometric observations using results from numerical simulations of star cluster evolution. COCOA is able to present the output of realistic numerical simulations of star clusters carried out using Monte Carlo or N-body codes in a way that is useful for direct comparison with photometric observations. The code can simulate optical observations from simulation snapshots in which positions and magnitudes of objects are known. The parameters for simulating the observations can be adjusted to mimic telescopes of various sizes. COCOA also has a photometry pipeline that can use standalone versions of DAOPHOT (ascl:1104.011) and ALLSTAR to produce photometric catalogs for all observed stars.

  9. Preliminary conceptual design about the CEPC calorimeters

    Science.gov (United States)

    Yang, Haijun

    2016-11-01

    The Circular Electron Positron Collider (CEPC) as a Higgs factory was proposed in September 2013. The preliminary conceptual design report was completed in 2015.1 The CEPC detector design was using International Linear Collider Detector — ILD2 as an initial baseline. The CEPC calorimeters, including the high granularity electromagnetic calorimeter (ECAL) and the hadron calorimeter (HCAL), are designed for precise energy measurements of electrons, photons, taus and hadronic jets. The basic resolution requirements for the ECAL and HCAL are about 16%E (GeV) and 50%E (GeV), respectively. To fully exploit the physics potential of the Higgs, W, Z and related Standard Model processes, the jet energy resolution is required to reach 3%-4%, or 30%/E (GeV) at energies below about 100 GeV. To achieve the required performance, a Particle Flow Algorithm (PFA) — oriented calorimetry system is being considered as the baseline design. The CEPC ECAL detector options include silicon-tungsten or scintillator-tungsten structures with analog readout, while the HCAL detector options have scintillator or gaseous detector as the active sensor and iron as the absorber. Some latest R&D studies about ECAL and HCAL within the CEPC working group is also presented.

  10. Overweight and urban pollution: preliminary results.

    Science.gov (United States)

    Ponticiello, Barnaba Giuseppina; Capozzella, Assunta; Di Giorgio, Valeria; Casale, Teodorico; Giubilati, Roberto; Tomei, Gianfranco; Tomei, Francesco; Rosati, Maria Valeria; Sancini, Angela

    2015-06-15

    The aim of this study is to determine whether in workers exposed to urban pollution the risk of developing overweight and obesity is higher in workers exposed to urban pollution compared to a control group. The study was conducted on 150 volunteers, 75 workers exposed to urban pollution (50 women and 25 men) and 75 indoor workers (50 women and 25 men). Once measured the weight and height and calculated body mass index (BMI) for each worker, the research was based on the comparison, between the two groups, of the mean values of the measurements and of the frequency of workers with BMI index higher than the cut-off of normality. The only statistically significant difference found was for the mean value of weight in women, which was higher among outdoor workers compared to indoor workers. The mean values of BMI and the frequency of workers with BMI higher than normal was higher among outdoor workers compared to indoor workers in both sexes, but not statistically significant. The data suggest that outdoor workers may be subject to an additional risk of developing obesity as a result of exposure to urban air pollution (which, like obesity, is a source of oxidative stress). So, our preliminary study encourages to continue this line of research by implementing the sample and considering all the confounding factors. Furthermore, the results highlight the necessity to take account of gender differences in the context of health surveillance of workers.

  11. Preliminary test results for the SVX4

    Energy Technology Data Exchange (ETDEWEB)

    Christofek, L.; Hanagaki, K.; Rapidis, P.; Utes, M.; /Fermilab

    2005-06-01

    We present and summarize the preliminary test results for SVX4 chip testing. There are presently two versions of the SVX4. Version 2 has on-chip bypassing and Version 1 does not. The on-chip bypassing is a layer of transistors under the front-end analog pipeline that acts as a bypassing capacitor for the voltage supply. Its size is about a microfarad. We aggressively choose to test Version 2 because of this feature. The feature is advantageous for hybrid design because it eliminates the need for an additional passive component on the hybrid itself by placing it on the actual SVX4 die. Also, the SVX4 was designed to operate in two modes: D. and CDF. One can set which mode the chip will operate by placing a jumper in the proper position on the SVX4 chip carrier. In either mode, the chip can either use the operating parameters from the shift register or the shadow register. Similarly, this is selected by placing a jumper on the SVX4 chip carrier. This chip has this feature because it was unknown whether the new design of the shadow register would be operable. The shadow register is also call the SEU register or Single Event Upset register. An introduction into the functionality of the chip and an explanation on the difference between D. and CDF mode can be found in the SVX4 User's Manual [1].

  12. Preliminary experiments on quantification of skin condition

    Science.gov (United States)

    Kitajima, Kenzo; Iyatomi, Hitoshi

    2014-03-01

    In this study, we investigated a preliminary assessment method for skin conditions such as a moisturizing property and its fineness of the skin with an image analysis only. We captured a facial images from volunteer subjects aged between 30s and 60s by Pocket Micro (R) device (Scalar Co., Japan). This device has two image capturing modes; the normal mode and the non-reflection mode with the aid of the equipped polarization filter. We captured skin images from a total of 68 spots from subjects' face using both modes (i.e. total of 136 skin images). The moisture-retaining property of the skin and subjective evaluation score of the skin fineness in 5-point scale for each case were also obtained in advance as a gold standard (their mean and SD were 35.15 +/- 3.22 (μS) and 3.45 +/- 1.17, respectively). We extracted a total of 107 image features from each image and built linear regression models for estimating abovementioned criteria with a stepwise feature selection. The developed model for estimating the skin moisture achieved the MSE of 1.92 (μS) with 6 selected parameters, while the model for skin fineness achieved that of 0.51 scales with 7 parameters under the leave-one-out cross validation. We confirmed the developed models predicted the moisture-retaining property and fineness of the skin appropriately with only captured image.

  13. The deuteron accelerator preliminary design for BISOL

    Energy Technology Data Exchange (ETDEWEB)

    Peng, S.X., E-mail: sxpeng@pku.edu.cn; Zhu, F.; Wang, Z.; Gao, Y.; Guo, Z.Y.

    2016-06-01

    BISOL, which was named as Beijing-ISOL before (Cui et al., 2013), is the abbreviation of Beijing Isotope-Separation-On-Line neutron beam facility. It is proposed jointly by Peking University (PKU) and China Institute of Atomic Energy (CIAE) for basic science study and application. It is a double driven facility that can be driven by a reactor or a deuteron accelerator. The deuteron driver accelerator should accelerate the deuteron beam up to 40 MeV with maximum beam current of 10 mA. Proton beams up to 33 MeV and He{sup 2+} beams up to 81.2 MeV can also be accelerated in this accelerator. The accelerator can be operated on either CW (continuous waveform) or pulsed mode, and the ion energy can be adjusted in a wide range. The accelerator will also allow independent operation of the RIB (Radioactive Ion Beams) system. It will be mainly charged by PKU group. Details of the deuteron accelerator preliminary design for BISOL will be given in this paper.

  14. Guidance for performing preliminary assessments under CERCLA

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-09-01

    EPA headquarters and a national site assessment workgroup produced this guidance for Regional, State, and contractor staff who manage or perform preliminary assessments (PAs). EPA has focused this guidance on the types of sites and site conditions most commonly encountered. The PA approach described in this guidance is generally applicable to a wide variety of sites. However, because of the variability among sites, the amount of information available, and the level of investigative effort required, it is not possible to provide guidance that is equally applicable to all sites. PA investigators should recognize this and be aware that variation from this guidance may be necessary for some sites, particularly for PAs performed at Federal facilities, PAs conducted under EPA`s Environmental Priorities Initiative (EPI), and PAs at sites that have previously been extensively investigated by EPA or others. The purpose of this guidance is to provide instructions for conducting a PA and reporting results. This guidance discusses the information required to evaluate a site and how to obtain it, how to score a site, and reporting requirements. This document also provides guidelines and instruction on PA evaluation, scoring, and the use of standard PA scoresheets. The overall goal of this guidance is to assist PA investigators in conducting high-quality assessments that result in correct site screening or further action recommendations on a nationally consistent basis.

  15. PRELIMINARY SELECTION OF MGR DESIGN BASIS EVENTS

    Energy Technology Data Exchange (ETDEWEB)

    J.A. Kappes

    1999-09-16

    The purpose of this analysis is to identify the preliminary design basis events (DBEs) for consideration in the design of the Monitored Geologic Repository (MGR). For external events and natural phenomena (e.g., earthquake), the objective is to identify those initiating events that the MGR will be designed to withstand. Design criteria will ensure that radiological release scenarios resulting from these initiating events are beyond design basis (i.e., have a scenario frequency less than once per million years). For internal (i.e., human-induced and random equipment failures) events, the objective is to identify credible event sequences that result in bounding radiological releases. These sequences will be used to establish the design basis criteria for MGR structures, systems, and components (SSCs) design basis criteria in order to prevent or mitigate radiological releases. The safety strategy presented in this analysis for preventing or mitigating DBEs is based on the preclosure safety strategy outlined in ''Strategy to Mitigate Preclosure Offsite Exposure'' (CRWMS M&O 1998f). DBE analysis is necessary to provide feedback and requirements to the design process, and also to demonstrate compliance with proposed 10 CFR 63 (Dyer 1999b) requirements. DBE analysis is also required to identify and classify the SSCs that are important to safety (ITS).

  16. STACEE-32: Design, performance, and preliminary results

    Science.gov (United States)

    Ong, Rene A.

    2000-06-01

    The Solar Tower Atmospheric Cherenkov Effect Experiment (STACEE) is designed to detect astrophysical sources of γ-rays at energies between 25 and 500 GeV. STACEE uses large solar mirrors (heliostats) to collect the atmospheric Cherenkov radiation produced in γ-ray air showers. The use of a large mirror collection area will allow STACEE to probe γ-ray sources at energies above the reach of the Compton Gamma Ray Observatory (CGRO), but below the reach of conventional Cherenkov telescopes. During the 1998-99 observing season, a portion of STACEE using 32 heliostats was installed at the National Solar Thermal Test Facility (NSTTF) of Sandia National Laboratories (Albuquerque, NM). This initial configuration (STACEE-32) observed a number of astronomical sources, including the Crab and several active galactic nuclei (AGN). Here we report on these observations. We highlight the experimental configuration and the preliminary results from the Crab data. The full STACEE experiment using 64 heliostats will be commissioned in 2000. .

  17. Preliminary pharmacognostic screening of Achyranthes coynei stem

    Directory of Open Access Journals (Sweden)

    Vinayak Upadhya

    2015-01-01

    Full Text Available Achyranthes coynei is a rare, endemic perennial shrub reported from Karnataka and Maharashtra states of India. The plant is used to treat various disorders by folk healers and was proven to have antimicrobial and antioxidant properties. The present study was undertaken to evaluate microscopic and macroscopic characters of A. coynei stem, along with its physicochemical parameters. ProgRes ® CapturePro and Microsoft Excel were used for statistical analysis. Perennial, shrubby nature and woody stem were the distinguishing morphological characters observed. Transverse section (TS illustrated quadrangular outline of the stem and showed the presence of two types of trichomes on the thick-walled epidermis. TS also showed number of rosette calcium oxalates crystals; prismatic and microsphenoid crystals; conjoint, collateral open secondary vascular bundles; and two amphixylic medullary bundles in the pith. Ash and extractive values, micro and macro elements and nutritive factors were estimated in the present study. The presence of alkaloids, saponins and triterpenoids were observed in preliminary phytochemical screening. High-performance thin layer chromatographic analysis yielded different bands and also indicated the presence of oleanolic acid. The studied parameters for A. coynei stem will be useful for identification and authentication of the plant material.

  18. Preliminary safety design analysis of KALIMER

    Energy Technology Data Exchange (ETDEWEB)

    Suk, Soo Dong; Kwon, Y. M.; Kim, K. D. [Korea Atomic Energy Research Institute, Taejon (Korea)

    1999-03-01

    The national long-term R and D program updated in 1997 requires Korea Atomic Energy Research Institute(KAERI) to complete by the year 2006 the basic design of Korea Advanced Liquid Metal Reactor (KALIMER), along with supporting R and D work, with the capability of resolving the issue of spent fuel storage as well as with significantly enhanced safety. KALIMER is a 150 MWe pool-type sodium cooled prototype reactor that uses metallic fuel. The conceptual design is currently under way to establish a self consistent design meeting a set of the major safety design requirements for accident prevention. Some of current emphasis include those for inherent and passive means of negative reactivity insertion and decay heat removal, high shutdown reliability, prevention of and protection from sodium chemical reaction, and high seismic margin, among others. All of these requirements affect the reactor design significantly and involve supporting R and D programs of substance. This document first introduces a set of safety design requirements and accident evaluation criteria established for the conceptual design of KALIMER and then summarizes some of the preliminary results of engineering and design analyses performed for the safety of KALIMER. 19 refs., 19 figs., 6 tabs. (Author)

  19. Preliminary study natural gas; Foerstudie naturgas

    Energy Technology Data Exchange (ETDEWEB)

    Lamnevik, Stefan; Carlsson, Tomas; Dyhr, Kurt

    2000-09-01

    FOA has carried out a preliminary study on natural gas for the Swedish National Energy Administration. To use natural gas as an energy source could be one step towards use of carbon-free fuels such as hydrogen. Natural gas, consisting mainly of methane, is the hydrocarbon with the highest hydrogen content. It has a high heat of combustion, 55 MJ/kg, and a low emission of carbon dioxide, 2.8 kg/kg fuel or 0.051 kg/MJ. The carbon dioxide emission per energy unit is twice as high for coal, 75% higher for wood fuels, and 27% higher for fuel oils. The Swedish natural gas network starts at Malmoe and ends at Hyltebruk. The natural gas used is imported from Denmark by Sydgas AB. It would be possible in the future to get connections to the Russian and the Norwegian networks and also to import LNG by ship and store it to buffer the different consumption demands during summer and winter. Natural gas is non-toxic but can be suffocating due to too low oxygen content at high concentrations. Combustion with an inadequate air supply will form toxic carbon monoxide like other carbonaceous fuels. Natural gas/air mixtures may explode like other gaseous fuels. The gas is lighter than air and is therefore dispersed better than heavier gases like LPG. Natural gas is difficult to detonate unlike other gases.

  20. Preliminary High-Throughput Metagenome Assembly

    Energy Technology Data Exchange (ETDEWEB)

    Dusheyko, Serge; Furman, Craig; Pangilinan, Jasmyn; Shapiro, Harris; Tu, Hank

    2007-03-26

    Metagenome data sets present a qualitatively different assembly problem than traditional single-organism whole-genome shotgun (WGS) assembly. The unique aspects of such projects include the presence of a potentially large number of distinct organisms and their representation in the data set at widely different fractions. In addition, multiple closely related strains could be present, which would be difficult to assemble separately. Failure to take these issues into account can result in poor assemblies that either jumble together different strains or which fail to yield useful results. The DOE Joint Genome Institute has sequenced a number of metagenomic projects and plans to considerably increase this number in the coming year. As a result, the JGI has a need for high-throughput tools and techniques for handling metagenome projects. We present the techniques developed to handle metagenome assemblies in a high-throughput environment. This includes a streamlined assembly wrapper, based on the JGI?s in-house WGS assembler, Jazz. It also includes the selection of sensible defaults targeted for metagenome data sets, as well as quality control automation for cleaning up the raw results. While analysis is ongoing, we will discuss preliminary assessments of the quality of the assembly results (http://fames.jgi-psf.org).

  1. Modeling Malaysia's Energy System: Some Preliminary Results

    Directory of Open Access Journals (Sweden)

    Ahmad M. Yusof

    2011-01-01

    Full Text Available Problem statement: The current dynamic and fragile world energy environment necessitates the development of new energy model that solely caters to analyze Malaysia’s energy scenarios. Approach: The model is a network flow model that traces the flow of energy carriers from its sources (import and mining through some conversion and transformation processes for the production of energy products to final destinations (energy demand sectors. The integration to the economic sectors is done exogeneously by specifying the annual sectoral energy demand levels. The model in turn optimizes the energy variables for a specified objective function to meet those demands. Results: By minimizing the inter temporal petroleum product imports for the crude oil system the annual extraction level of Tapis blend is projected at 579600 barrels per day. The aggregate demand for petroleum products is projected to grow at 2.1% year-1 while motor gasoline and diesel constitute 42 and 38% of the petroleum products demands mix respectively over the 5 year planning period. Petroleum products import is expected to grow at 6.0% year-1. Conclusion: The preliminary results indicate that the model performs as expected. Thus other types of energy carriers such as natural gas, coal and biomass will be added to the energy system for the overall development of Malaysia energy model.

  2. Preliminary design of surrounding heliostat fields

    Energy Technology Data Exchange (ETDEWEB)

    Collado, Francisco J. [Zaragoza University, Dpto. de Ingenieria Mecanica, CPS-B, Maria de Luna 3, 50018 Zaragoza (Spain)

    2009-05-15

    Recently, the author has shown elsewhere a simplified model that allows quick evaluations of the annual overall energy collected by a surrounding heliostat field. This model is the combination of an analytical flux density function produced by a heliostat, developed by the own author, and an optimized mirror density distribution developed by University of Houston for the Solar One Project. As main conclusion of this previous work, it was recognized that such pseudo-continuous simplified model should not substitute much more accurate discrete evaluations, which manage thousands of individual heliostat coordinates. Here in this work, the difficulty of generating a preliminary discrete layout of a large number of heliostats is addressed. The main novelty is the direct definition of thousands of heliostat coordinates through basically two parameters i.e. a simplified blocking factor and an additional security distance. Such procedure, which was formerly theoretically suggested by the author, is put into practice here, showing examples and commenting their problems and advantages. Getting a previous set of thousands of heliostat coordinates would be a major first step in the complex process of designing solar power tower (SPT). (author)

  3. Sociology of diagnosis: a preliminary review.

    Science.gov (United States)

    Jutel, Annemarie

    2009-03-01

    Diagnoses are the classification tools of medicine, and are pivotal in the ways medicine exerts its role in society. Their sociological study is commonly subsumed under the rubrics of medicalisation, history of medicine and theory of disease. Diagnosis is, however, a powerful social tool, with unique features and impacts which deserve their own specific analysis. The process of diagnosis provides the framework within which medicine operates, punctuates the values which medicine espouses, and underlines the authoritative role of both medicine and the doctor. Diagnosis takes place at a salient juncture between illness and disease, patient and doctor, complaint and explanation. Despite calls for its establishment, almost two decades ago (Brown 1990), there is not yet a clear sociology of diagnosis. This paper argues that there should be, and, as a first step, draws together a number of threads of medical sociology that potentially contribute to this proposed sociology of diagnosis, including the place of diagnosis in the institution of medicine, the social framing of disease definitions, the means by which diagnosis confers authority to medicine, and how that authority is challenged. Through this preliminary review, I encourage sociology to consider the specific role of diagnosis in view of establishing a specific sub-disciplinary field.

  4. ALMA Nutator Design and Preliminary Performance

    CERN Document Server

    Martin-Cocher, Pierre; Koch, Patrick M; Ni, Chih-Wen; Chen, Wei-Long; Chen, Ming-Tang; Raffin, Philippe; Ong, Chin-Long; Ho, Paul T P; Symmes, Arthur

    2013-01-01

    We report the past two years of collaboration between the di?erent actors on the ALMA nutator. Building on previous developments, the nutator has seen changes in much of the design. A high-modulus carbon ?fiber structure has been added on the back of the mirror in order to transfer the voice coils forces with less deformation, thus reducing delay problems due to flexing. The controller is now an off?-the-shelf National Instrument NI-cRIO, and the ampli?fier a class D servo drive from Advanced Motion Controls, with high peak power able to drive the coils at 300 Volts DC. The stow mechanism has been totally redesigned to improve on the repeatability and precision of the stow position, which is also the reference for the 26 bits Heidenhain encoders. This also improves on the accuracy of the stow position with wind loading. Finally, the software, written largely with National Instrument's LabView, has been developed. We will discuss these changes and the preliminary performances achieved to date. Keywords: ALMA, ...

  5. The deuteron accelerator preliminary design for BISOL

    Science.gov (United States)

    Peng, S. X.; Zhu, F.; Wang, Z.; Gao, Y.; Guo, Z. Y.

    2016-06-01

    BISOL, which was named as Beijing_ISOL before (Cui et al., 2013), is the abbreviation of Beijing Isotope-Separation-On-Line neutron beam facility. It is proposed jointly by Peking University (PKU) and China Institute of Atomic Energy (CIAE) for basic science study and application. It is a double driven facility that can be driven by a reactor or a deuteron accelerator. The deuteron driver accelerator should accelerate the deuteron beam up to 40 MeV with maximum beam current of 10 mA. Proton beams up to 33 MeV and He2+ beams up to 81.2 MeV can also be accelerated in this accelerator. The accelerator can be operated on either CW (continuous waveform) or pulsed mode, and the ion energy can be adjusted in a wide range. The accelerator will also allow independent operation of the RIB (Radioactive Ion Beams) system. It will be mainly charged by PKU group. Details of the deuteron accelerator preliminary design for BISOL will be given in this paper.

  6. Prostate elastography: preliminary in vivo results

    Science.gov (United States)

    Alam, S. K.; Feleppa, E. J.; Kalisz, A.; Ramchandran, S.; Ennis, R. D.; Lizzi, Frederick L.; Wuu, C.-S.; Ketterling, Jeffrey A.

    2005-04-01

    We report preliminary results from our investigation of in vivo prostate elastography. Fewer than 50% of all prostate cancers are typically visible in current clinical imaging modalities. Elastography displays a map of strain that results when tissue is externally compressed. Thus, elastography is ideal for imaging prostate cancers because they are generally stiffer than the surrounding tissue and stiffer regions usually exhibit lower strain in elastograms. In our study, digital radio-frequency (RF) ultrasound echo data were acquired from prostate-cancer patients undergoing brachytherapy. Seed placement is guided by a transrectal ultrasound (TRUS) probe, which is held in a mechanical fixture. The probe can be moved in XYZ directions and tilted. The probe face, in contact with the rectal wall, is used to apply a compression force to the immediately adjacent prostate. We also used a water-filled (acoustic) coupling balloon to compress the prostate by increasing the water volume inside the balloon. In each scan plane (transverse), we acquired RF data from successive scans at the scanner frame rate as the deformation force on the rectal wall was continuously increased. We computed strain using 1D RF cross-correlation analysis. The compression method based on fixture displacement produced low-noise elastograms that beautifully displayed the prostate architecture and emphasized stiff areas. Balloon-based compression also produced low-noise elastograms. Initial results demonstrate that elastography may be useful in the detection and evaluation of prostate cancers, occult in conventional imaging modalities.

  7. Automated military unit identification in battlefield simulation

    Energy Technology Data Exchange (ETDEWEB)

    Stroud, P.; Gordon, R.

    1997-05-01

    It is the nature of complex systems, composed of many interacting elements, that unanticipated phenomena develop. Computer simulation, in which the elements of a complex system are implemented as interacting software objects (actors), is an effective tool to study collective and emergent phenomena in complex systems. A new cognitive architecture is described for constructing simulation actors that can, like the intelligent elements they represent adapt to unanticipated conditions. This cognitive architecture generates trial behaviors, estimates their fitness using an internal representation of the system, and has an internal apparatus for evolving a population of trial behaviors to changing environmental conditions. A specific simulation actor is developed to evaluate surveillance radar images of moving vehicles on battlefields. The vehicle cluster location, characterization and discrimination processes currently performed by intelligent human operators were implemented into a parameterized formation recognition process by using a newly developed family of 2D cluster filters. The mechanics of these cluster filters are described. Preliminary results are presented in which this GSM actor demonstrates the ability not only to recognize military formations under prescribed conditions, but to adapt its behavior to unanticipated conditions that develop in the complex simulated battlefield system.

  8. The ATLAS Simulation Infrastructure

    CERN Document Server

    Aad, Georges; Abdallah, Jalal; Abdelalim, Ahmed Ali; Abdesselam, Abdelouahab; Abdinov, Ovsat; Abi, Babak; Abolins, Maris; Abramowicz, Halina; Abreu, Henso; Acharya, Bobby Samir; Adams, David; Addy, Tetteh; Adelman, Jahred; Adorisio, Cristina; Adragna, Paolo; Adye, Tim; Aefsky, Scott; Aguilar-Saavedra, Juan Antonio; Aharrouche, Mohamed; Ahlen, Steven; Ahles, Florian; Ahmad, Ashfaq; Ahmed, Hossain; Ahsan, Mahsana; Aielli, Giulio; Akdogan, Taylan; Åkesson, Torsten Paul Ake; Akimoto, Ginga; Akimov , Andrei; Aktas, Adil; Alam, Mohammad; Alam, Muhammad Aftab; Albrand, Solveig; Aleksa, Martin; Aleksandrov, Igor; Alexa, Calin; Alexander, Gideon; Alexandre, Gauthier; Alexopoulos, Theodoros; Alhroob, Muhammad; Aliev, Malik; Alimonti, Gianluca; Alison, John; Aliyev, Magsud; Allport, Phillip; Allwood-Spiers, Sarah; Almond, John; Aloisio, Alberto; Alon, Raz; Alonso, Alejandro; Alviggi, Mariagrazia; Amako, Katsuya; Amelung, Christoph; Amorim, Antonio; Amorós, Gabriel; Amram, Nir; Anastopoulos, Christos; Andeen, Timothy; Anders, Christoph Falk; Anderson, Kelby; Andreazza, Attilio; Andrei, George Victor; Anduaga, Xabier; Angerami, Aaron; Anghinolfi, Francis; Anjos, Nuno; Annovi, Alberto; Antonaki, Ariadni; Antonelli, Mario; Antonelli, Stefano; Antos, Jaroslav; Antunovic, Bijana; Anulli, Fabio; Aoun, Sahar; Arabidze, Giorgi; Aracena, Ignacio; Arai, Yasuo; Arce, Ayana; Archambault, John-Paul; Arfaoui, Samir; Arguin, Jean-Francois; Argyropoulos, Theodoros; Arik, Metin; Armbruster, Aaron James; Arnaez, Olivier; Arnault, Christian; Artamonov, Andrei; Arutinov, David; Asai, Makoto; Asai, Shoji; Silva, José; Asfandiyarov, Ruslan; Ask, Stefan; Åsman, Barbro; Asner, David; Asquith, Lily; Assamagan, Ketevi; Astbury, Alan; Astvatsatourov, Anatoli; Atoian, Grigor; Auerbach, Benjamin; Augsten, Kamil; Aurousseau, Mathieu; Austin, Nicholas; Avolio, Giuseppe; Avramidou, Rachel Maria; Axen, David; Ay, Cano; Azuelos, Georges; Azuma, Yuya; Baak, Max; Bach, Andre; Bachacou, Henri; Bachas, Konstantinos; Backes, Moritz; Badescu, Elisabeta; Bagnaia, Paolo; Bai, Yu; Bain, Travis; Baines, John; Baker, Mark; Baker, Oliver Keith; Baker, Sarah; Baltasar Dos Santos Pedrosa, Fernando; Banas, Elzbieta; Banerjee, Piyali; Banerjee, Swagato; Banfi, Danilo; Bangert, Andrea Michelle; Bansal, Vikas; Baranov, Sergey; Baranov, Sergei; Barashkou, Andrei; Barber, Tom; Barberio, Elisabetta Luigia; Barberis, Dario; Barbero, Marlon; Bardin, Dmitri; Barillari, Teresa; Barisonzi, Marcello; Barklow, Timothy; Barlow, Nick; Barnett, Bruce; Barnett, Michael; Baroncelli, Antonio; Barr, Alan; Barreiro, Fernando; Barreiro Guimarães da Costa, João; Barrillon, Pierre; Bartoldus, Rainer; Bartsch, Detlef; Bates, Richard; Batkova, Lucia; Batley, Richard; Battaglia, Andreas; Battistin, Michele; Bauer, Florian; Bawa, Harinder Singh; Bazalova, Magdalena; Beare, Brian; Beau, Tristan; Beauchemin, Pierre-Hugues; Beccherle, Roberto; Becerici, Neslihan; Bechtle, Philip; Beck, Graham; Beck, Hans Peter; Beckingham, Matthew; Becks, Karl-Heinz; Beddall, Ayda; Beddall, Andrew; Bednyakov, Vadim; Bee, Christopher; Begel, Michael; Behar Harpaz, Silvia; Behera, Prafulla; Beimforde, Michael; Belanger-Champagne, Camille; Bell, Paul; Bell, William; Bella, Gideon; Bellagamba, Lorenzo; Bellina, Francesco; Bellomo, Massimiliano; Belloni, Alberto; Belotskiy, Konstantin; Beltramello, Olga; Ben Ami, Sagi; Benary, Odette; Benchekroun, Driss; Bendel, Markus; Benedict, Brian Hugues; Benekos, Nektarios; Benhammou, Yan; Benincasa, Gianpaolo; Benjamin, Douglas; Benoit, Mathieu; Bensinger, James; Benslama, Kamal; Bentvelsen, Stan; Beretta, Matteo; Berge, David; Bergeaas Kuutmann, Elin; Berger, Nicolas; Berghaus, Frank; Berglund, Elina; Beringer, Jürg; Bernat, Pauline; Bernhard, Ralf; Bernius, Catrin; Berry, Tracey; Bertin, Antonio; Besana, Maria Ilaria; Besson, Nathalie; Bethke, Siegfried; Bianchi, Riccardo-Maria; Bianco, Michele; Biebel, Otmar; Biesiada, Jed; Biglietti, Michela; Bilokon, Halina; Bindi, Marcello; Binet, Sebastien; Bingul, Ahmet; Bini, Cesare; Biscarat, Catherine; Bitenc, Urban; Black, Kevin; Blair, Robert; Blanchard, Jean-Baptiste; Blanchot, Georges; Blocker, Craig; Blondel, Alain; Blum, Walter; Blumenschein, Ulrike; Bobbink, Gerjan; Bocci, Andrea; Boehler, Michael; Boek, Jennifer; Boelaert, Nele; Böser, Sebastian; Bogaerts, Joannes Andreas; Bogouch, Andrei; Bohm, Christian; Bohm, Jan; Boisvert, Veronique; Bold, Tomasz; Boldea, Venera; Bondarenko, Valery; Bondioli, Mario; Boonekamp, Maarten; Bordoni, Stefania; Borer, Claudia; Borisov, Anatoly; Borissov, Guennadi; Borjanovic, Iris; Borroni, Sara; Bos, Kors; Boscherini, Davide; Bosman, Martine; Boterenbrood, Hendrik; Bouchami, Jihene; Boudreau, Joseph; Bouhova-Thacker, Evelina Vassileva; Boulahouache, Chaouki; Bourdarios, Claire; Boveia, Antonio; Boyd, James; Boyko, Igor; Bozovic-Jelisavcic, Ivanka; Bracinik, Juraj; Braem, André; Branchini, Paolo; Brandenburg, George; Brandt, Andrew; Brandt, Gerhard; Brandt, Oleg; Bratzler, Uwe; Brau, Benjamin; Brau, James; Braun, Helmut; Brelier, Bertrand; Bremer, Johan; Brenner, Richard; Bressler, Shikma; Britton, Dave; Brochu, Frederic; Brock, Ian; Brock, Raymond; Brodet, Eyal; Bromberg, Carl; Brooijmans, Gustaaf; Brooks, William; Brown, Gareth; Bruckman de Renstrom, Pawel; Bruncko, Dusan; Bruneliere, Renaud; Brunet, Sylvie; Bruni, Alessia; Bruni, Graziano; Bruschi, Marco; Bucci, Francesca; Buchanan, James; Buchholz, Peter; Buckley, Andrew; Budagov, Ioulian; Budick, Burton; Büscher, Volker; Bugge, Lars; Bulekov, Oleg; Bunse, Moritz; Buran, Torleiv; Burckhart, Helfried; Burdin, Sergey; Burgess, Thomas; Burke, Stephen; Busato, Emmanuel; Bussey, Peter; Buszello, Claus-Peter; Butin, Françcois; Butler, Bart; Butler, John; Buttar, Craig; Butterworth, Jonathan; Byatt, Tom; Caballero, Jose; Cabrera Urbán, Susana; Caforio, Davide; Cakir, Orhan; Calafiura, Paolo; Calderini, Giovanni; Calfayan, Philippe; Calkins, Robert; Caloba, Luiz; Calvet, David; Camarri, Paolo; Cameron, David; Campana, Simone; Campanelli, Mario; Canale, Vincenzo; Canelli, Florencia; Canepa, Anadi; Cantero, Josu; Capasso, Luciano; Capeans Garrido, Maria Del Mar; Caprini, Irinel; Caprini, Mihai; Capua, Marcella; Caputo, Regina; Caramarcu, Costin; Cardarelli, Roberto; Carli, Tancredi; Carlino, Gianpaolo; Carminati, Leonardo; Caron, Bryan; Caron, Sascha; Carrillo Montoya, German D.; Carron Montero, Sebastian; Carter, Antony; Carter, Janet; Carvalho, João; Casadei, Diego; Casado, Maria Pilar; Cascella, Michele; Castaneda Hernandez, Alfredo Martin; Castaneda-Miranda, Elizabeth; Castillo Gimenez, Victoria; Castro, Nuno Filipe; Cataldi, Gabriella; Catinaccio, Andrea; Catmore, James; Cattai, Ariella; Cattani, Giordano; Caughron, Seth; Cauz, Diego; Cavalleri, Pietro; Cavalli, Donatella; Cavalli-Sforza, Matteo; Cavasinni, Vincenzo; Ceradini, Filippo; Cerqueira, Augusto Santiago; Cerri, Alessandro; Cerrito, Lucio; Cerutti, Fabio; Cetin, Serkant Ali; Chafaq, Aziz; Chakraborty, Dhiman; Chan, Kevin; Chapman, John Derek; Chapman, John Wehrley; Chareyre, Eve; Charlton, Dave; Chavda, Vikash; Cheatham, Susan; Chekanov, Sergei; Chekulaev, Sergey; Chelkov, Gueorgui; Chen, Hucheng; Chen, Shenjian; Chen, Xin; Cheplakov, Alexander; Chepurnov, Vladimir; Cherkaoui El Moursli, Rajaa; Tcherniatine, Valeri; Chesneanu, Daniela; Cheu, Elliott; Cheung, Sing-Leung; Chevalier, Laurent; Chevallier, Florent; Chiarella, Vitaliano; Chiefari, Giovanni; Chikovani, Leila; Childers, John Taylor; Chilingarov, Alexandre; Chiodini, Gabriele; Chizhov, Mihail; Choudalakis, Georgios; Chouridou, Sofia; Christidi, Illectra-Athanasia; Christov, Asen; Chromek-Burckhart, Doris; Chu, Ming-Lee; Chudoba, Jiri; Ciapetti, Guido; Ciftci, Abbas Kenan; Ciftci, Rena; Cinca, Diane; Cindro, Vladimir; Ciobotaru, Matei Dan; Ciocca, Claudia; Ciocio, Alessandra; Cirilli, Manuela; Citterio, Mauro; Clark, Allan G.; Clark, Philip James; Cleland, Bill; Clemens, Jean-Claude; Clement, Benoit; Clement, Christophe; Coadou, Yann; Cobal, Marina; Coccaro, Andrea; Cochran, James H.; Coggeshall, James; Cogneras, Eric; Colijn, Auke-Pieter; Collard, Caroline; Collins, Neil; Collins-Tooth, Christopher; Collot, Johann; Colon, German; Conde Muiño, Patricia; Coniavitis, Elias; Consonni, Michele; Constantinescu, Serban; Conta, Claudio; Conventi, Francesco; Cooke, Mark; Cooper, Ben; Cooper-Sarkar, Amanda; Cooper-Smith, Neil; Copic, Katherine; Cornelissen, Thijs; Corradi, Massimo; Corriveau, Francois; Corso-Radu, Alina; Cortes-Gonzalez, Arely; Cortiana, Giorgio; Costa, Giuseppe; Costa, María José; Costanzo, Davide; Costin, Tudor; Côté, David; Coura Torres, Rodrigo; Courneyea, Lorraine; Cowan, Glen; Cowden, Christopher; Cox, Brian; Cranmer, Kyle; Cranshaw, Jack; Cristinziani, Markus; Crosetti, Giovanni; Crupi, Roberto; Crépé-Renaudin, Sabine; Cuenca Almenar, Cristóbal; Cuhadar Donszelmann, Tulay; Curatolo, Maria; Curtis, Chris; Cwetanski, Peter; Czyczula, Zofia; D'Auria, Saverio; D'Onofrio, Monica; D'Orazio, Alessia; Da Via, Cinzia; Dabrowski, Wladyslaw; Dai, Tiesheng; Dallapiccola, Carlo; Dallison, Steve; Daly, Colin; Dam, Mogens; Danielsson, Hans Olof; Dannheim, Dominik; Dao, Valerio; Darbo, Giovanni; Darlea, Georgiana Lavinia; Davey, Will; Davidek, Tomas; Davidson, Nadia; Davidson, Ruth; Davies, Merlin; Davison, Adam; Dawson, Ian; Daya, Rozmin; De, Kaushik; de Asmundis, Riccardo; De Castro, Stefano; De Castro Faria Salgado, Pedro; De Cecco, Sandro; de Graat, Julien; De Groot, Nicolo; de Jong, Paul; De Mora, Lee; De Oliveira Branco, Miguel; De Pedis, Daniele; De Salvo, Alessandro; De Sanctis, Umberto; De Santo, Antonella; De Vivie De Regie, Jean-Baptiste; De Zorzi, Guido; Dean, Simon; Dedovich, Dmitri; Degenhardt, James; Dehchar, Mohamed; Del Papa, Carlo; Del Peso, Jose; Del Prete, Tarcisio; Dell'Acqua, Andrea; Dell'Asta, Lidia; Della Pietra, Massimo; della Volpe, Domenico; Delmastro, Marco; Delsart, Pierre-Antoine; Deluca, Carolina; Demers, Sarah; Demichev, Mikhail; Demirkoz, Bilge; Deng, Jianrong; Deng, Wensheng; Denisov, Sergey; Derkaoui, Jamal Eddine; Derue, Frederic; Dervan, Paul; Desch, Klaus Kurt; Deviveiros, Pier-Olivier; Dewhurst, Alastair; DeWilde, Burton; Dhaliwal, Saminder; Dhullipudi, Ramasudhakar; Di Ciaccio, Anna; Di Ciaccio, Lucia; Di Domenico, Antonio; Di Girolamo, Alessandro; Di Girolamo, Beniamino; Di Luise, Silvestro; Di Mattia, Alessandro; Di Nardo, Roberto; Di Simone, Andrea; Di Sipio, Riccardo; Diaz, Marco Aurelio; Diblen, Faruk; Diehl, Edward; Dietrich, Janet; Dietzsch, Thorsten; Diglio, Sara; Dindar Yagci, Kamile; Dingfelder, Jochen; Dionisi, Carlo; Dita, Petre; Dita, Sanda; Dittus, Fridolin; Djama, Fares; Djilkibaev, Rashid; Djobava, Tamar; do Vale, Maria Aline Barros; Do Valle Wemans, André; Doan, Thi Kieu Oanh; Dobos, Daniel; Dobson, Ellie; Dobson, Marc; Doglioni, Caterina; Doherty, Tom; Dolejsi, Jiri; Dolenc, Irena; Dolezal, Zdenek; Dolgoshein, Boris; Dohmae, Takeshi; Donega, Mauro; Donini, Julien; Dopke, Jens; Doria, Alessandra; Dos Anjos, Andre; Dotti, Andrea; Dova, Maria-Teresa; Doxiadis, Alexander; Doyle, Tony; Drasal, Zbynek; Dris, Manolis; Dubbert, Jörg; Duchovni, Ehud; Duckeck, Guenter; Dudarev, Alexey; Dudziak, Fanny; Dührssen , Michael; Duflot, Laurent; Dufour, Marc-Andre; Dunford, Monica; Duran Yildiz, Hatice; Dushkin, Andrei; Duxfield, Robert; Dwuznik, Michal; Düren, Michael; Ebenstein, William; Ebke, Johannes; Eckweiler, Sebastian; Edmonds, Keith; Edwards, Clive; Egorov, Kirill; Ehrenfeld, Wolfgang; Ehrich, Thies; Eifert, Till; Eigen, Gerald; Einsweiler, Kevin; Eisenhandler, Eric; Ekelof, Tord; El Kacimi, Mohamed; Ellert, Mattias; Elles, Sabine; Ellinghaus, Frank; Ellis, Katherine; Ellis, Nicolas; Elmsheuser, Johannes; Elsing, Markus; Emeliyanov, Dmitry; Engelmann, Roderich; Engl, Albert; Epp, Brigitte; Eppig, Andrew; Erdmann, Johannes; Ereditato, Antonio; Eriksson, Daniel; Ermoline, Iouri; Ernst, Jesse; Ernst, Michael; Ernwein, Jean; Errede, Deborah; Errede, Steven; Ertel, Eugen; Escalier, Marc; Escobar, Carlos; Espinal Curull, Xavier; Esposito, Bellisario; Etienvre, Anne-Isabelle; Etzion, Erez; Evans, Hal; Fabbri, Laura; Fabre, Caroline; Facius, Katrine; Fakhrutdinov, Rinat; Falciano, Speranza; Fang, Yaquan; Fanti, Marcello; Farbin, Amir; Farilla, Addolorata; Farley, Jason; Farooque, Trisha; Farrington, Sinead; Farthouat, Philippe; Fassnacht, Patrick; Fassouliotis, Dimitrios; Fatholahzadeh, Baharak; Fayard, Louis; Fayette, Florent; Febbraro, Renato; Federic, Pavol; Fedin, Oleg; Fedorko, Woiciech; Feligioni, Lorenzo; Felzmann, Ulrich; Feng, Cunfeng; Feng, Eric; Fenyuk, Alexander; Ferencei, Jozef; Ferland, Jonathan; Fernandes, Bruno; Fernando, Waruna; Ferrag, Samir; Ferrando, James; Ferrara, Valentina; Ferrari, Arnaud; Ferrari, Pamela; Ferrari, Roberto; Ferrer, Antonio; Ferrer, Maria Lorenza; Ferrere, Didier; Ferretti, Claudio; Fiascaris, Maria; Fiedler, Frank; Filipčič, Andrej; Filippas, Anastasios; Filthaut, Frank; Fincke-Keeler, Margret; Fiolhais, Miguel; Fiorini, Luca; Firan, Ana; Fischer, Gordon; Fisher, Matthew; Flechl, Martin; Fleck, Ivor; Fleckner, Johanna; Fleischmann, Philipp; Fleischmann, Sebastian; Flick, Tobias; Flores Castillo, Luis; Flowerdew, Michael; Fonseca Martin, Teresa; Formica, Andrea; Forti, Alessandra; Fortin, Dominique; Fournier, Daniel; Fowler, Andrew; Fowler, Ken; Fox, Harald; Francavilla, Paolo; Franchino, Silvia; Francis, David; Franklin, Melissa; Franz, Sebastien; Fraternali, Marco; Fratina, Sasa; Freestone, Julian; French, Sky; Froeschl, Robert; Froidevaux, Daniel; Frost, James; Fukunaga, Chikara; Fullana Torregrosa, Esteban; Fuster, Juan; Gabaldon, Carolina; Gabizon, Ofir; Gadfort, Thomas; Gadomski, Szymon; Gagliardi, Guido; Gagnon, Pauline; Galea, Cristina; Gallas, Elizabeth; Gallas, Manuel; Gallo, Valentina Santina; Gallop, Bruce; Gallus, Petr; Galyaev, Eugene; Gan, K K; Gao, Yongsheng; Gaponenko, Andrei; Garcia-Sciveres, Maurice; García, Carmen; García Navarro, José Enrique; Gardner, Robert; Garelli, Nicoletta; Garitaonandia, Hegoi; Garonne, Vincent; Gatti, Claudio; Gaudio, Gabriella; Gautard, Valerie; Gauzzi, Paolo; Gavrilenko, Igor; Gay, Colin; Gaycken, Goetz; Gazis, Evangelos; Ge, Peng; Gee, Norman; Geich-Gimbel, Christoph; Gellerstedt, Karl; Gemme, Claudia; Genest, Marie-Hélène; Gentile, Simonetta; Georgatos, Fotios; George, Simon; Gershon, Avi; Ghazlane, Hamid; Ghodbane, Nabil; Giacobbe, Benedetto; Giagu, Stefano; Giakoumopoulou, Victoria; Giangiobbe, Vincent; Gianotti, Fabiola; Gibbard, Bruce; Gibson, Adam; Gibson, Stephen; Gilbert, Laura; Gilchriese, Murdock; Gilewsky, Valentin; Gingrich, Douglas; Ginzburg, Jonatan; Giokaris, Nikos; Giordani, MarioPaolo; Giordano, Raffaele; Giorgi, Francesco Michelangelo; Giovannini, Paola; Giraud, Pierre-Francois; Girtler, Peter; Giugni, Danilo; Giusti, Paolo; Gjelsten, Børge Kile; Gladilin, Leonid; Glasman, Claudia; Glazov, Alexandre; Glitza, Karl-Walter; Glonti, George; Godfrey, Jennifer; Godlewski, Jan; Goebel, Martin; Göpfert, Thomas; Goeringer, Christian; Gössling, Claus; Göttfert, Tobias; Goggi, Virginio; Goldfarb, Steven; Goldin, Daniel; Golling, Tobias; Gomes, Agostinho; Gomez Fajardo, Luz Stella; Gonçcalo, Ricardo; Gonella, Laura; Gong, Chenwei; González de la Hoz, Santiago; Gonzalez Silva, Laura; Gonzalez-Sevilla, Sergio; Goodson, Jeremiah Jet; Goossens, Luc; Gordon, Howard; Gorelov, Igor; Gorfine, Grant; Gorini, Benedetto; Gorini, Edoardo; Gorišek, Andrej; Gornicki, Edward; Gosdzik, Bjoern; Gosselink, Martijn; Gostkin, Mikhail Ivanovitch; Gough Eschrich, Ivo; Gouighri, Mohamed; Goujdami, Driss; Goulette, Marc Phillippe; Goussiou, Anna; Goy, Corinne; Grabowska-Bold, Iwona; Grafström, Per; Grahn, Karl-Johan; Grancagnolo, Sergio; Grassi, Valerio; Gratchev, Vadim; Grau, Nathan; Gray, Heather; Gray, Julia Ann; Graziani, Enrico; Green, Barry; Greenshaw, Timothy; Greenwood, Zeno Dixon; Gregor, Ingrid-Maria; Grenier, Philippe; Griesmayer, Erich; Griffiths, Justin; Grigalashvili, Nugzar; Grillo, Alexander; Grimm, Kathryn; Grinstein, Sebastian; Grishkevich, Yaroslav; Groh, Manfred; Groll, Marius; Gross, Eilam; Grosse-Knetter, Joern; Groth-Jensen, Jacob; Grybel, Kai; Guicheney, Christophe; Guida, Angelo; Guillemin, Thibault; Guler, Hulya; Gunther, Jaroslav; Guo, Bin; Gupta, Ambreesh; Gusakov, Yury; Gutierrez, Andrea; Gutierrez, Phillip; Guttman, Nir; Gutzwiller, Olivier; Guyot, Claude; Gwenlan, Claire; Gwilliam, Carl; Haas, Andy; Haas, Stefan; Haber, Carl; Hadavand, Haleh Khani; Hadley, David; Haefner, Petra; Härtel, Roland; Hajduk, Zbigniew; Hakobyan, Hrachya; Haller, Johannes; Hamacher, Klaus; Hamilton, Andrew; Hamilton, Samuel; Han, Liang; Hanagaki, Kazunori; Hance, Michael; Handel, Carsten; Hanke, Paul; Hansen, Jørgen Beck; Hansen, Jorn Dines; Hansen, John Renner; Hansen, Peter Henrik; Hansl-Kozanecka, Traudl; Hansson, Per; Hara, Kazuhiko; Hare, Gabriel; Harenberg, Torsten; Harrington, Robert; Harris, Orin; Harrison, Karl; Hartert, Jochen; Hartjes, Fred; Harvey, Alex; Hasegawa, Satoshi; Hasegawa, Yoji; Hashemi, Kevan; Hassani, Samira; Haug, Sigve; Hauschild, Michael; Hauser, Reiner; Havranek, Miroslav; Hawkes, Christopher; Hawkings, Richard John; Hayakawa, Takashi; Hayward, Helen; Haywood, Stephen; Head, Simon; Hedberg, Vincent; Heelan, Louise; Heim, Sarah; Heinemann, Beate; Heisterkamp, Simon; Helary, Louis; Heller, Mathieu; Hellman, Sten; Helsens, Clement; Hemperek, Tomasz; Henderson, Robert; Henke, Michael; Henrichs, Anna; Henriques Correia, Ana Maria; Henrot-Versille, Sophie; Hensel, Carsten; Henß, Tobias; Hernández Jiménez, Yesenia; Hershenhorn, Alon David; Herten, Gregor; Hertenberger, Ralf; Hervas, Luis; Hessey, Nigel; Higón-Rodriguez, Emilio; Hill, John; Hiller, Karl Heinz; Hillert, Sonja; Hillier, Stephen; Hinchliffe, Ian; Hines, Elizabeth; Hirose, Minoru; Hirsch, Florian; Hirschbuehl, Dominic; Hobbs, John; Hod, Noam; Hodgkinson, Mark; Hodgson, Paul; Hoecker, Andreas; Hoeferkamp, Martin; Hoffman, Julia; Hoffmann, Dirk; Hohlfeld, Marc; Holy, Tomas; Holzbauer, Jenny; Homma, Yasuhiro; Horazdovsky, Tomas; Hori, Takuya; Horn, Claus; Horner, Stephan; Hostachy, Jean-Yves; Hou, Suen; Hoummada, Abdeslam; Howe, Travis; Hrivnac, Julius; Hryn'ova, Tetiana; Hsu, Pai-hsien Jennifer; Hsu, Shih-Chieh; Huang, Guang Shun; Hubacek, Zdenek; Hubaut, Fabrice; Huegging, Fabian; Hughes, Emlyn; Hughes, Gareth; Hurwitz, Martina; Husemann, Ulrich; Huseynov, Nazim; Huston, Joey; Huth, John; Iacobucci, Giuseppe; Iakovidis, Georgios; Ibragimov, Iskander; Iconomidou-Fayard, Lydia; Idarraga, John; Iengo, Paolo; Igonkina, Olga; Ikegami, Yoichi; Ikeno, Masahiro; Ilchenko, Yuri; Iliadis, Dimitrios; Ince, Tayfun; Ioannou, Pavlos; Iodice, Mauro; Irles Quiles, Adrian; Ishikawa, Akimasa; Ishino, Masaya; Ishmukhametov, Renat; Isobe, Tadaaki; Issakov, Vladimir; Issever, Cigdem; Istin, Serhat; Itoh, Yuki; Ivashin, Anton; Iwanski, Wieslaw; Iwasaki, Hiroyuki; Izen, Joseph; Izzo, Vincenzo; Jackson, Brett; Jackson, John; Jackson, Paul; Jaekel, Martin; Jain, Vivek; Jakobs, Karl; Jakobsen, Sune; Jakubek, Jan; Jana, Dilip; Jansen, Eric; Jantsch, Andreas; Janus, Michel; Jared, Richard; Jarlskog, Göran; Jeanty, Laura; Jen-La Plante, Imai; Jenni, Peter; Jež, Pavel; Jézéquel, Stéphane; Ji, Weina; Jia, Jiangyong; Jiang, Yi; Jimenez Belenguer, Marcos; Jin, Shan; Jinnouchi, Osamu; Joffe, David; Johansen, Marianne; Johansson, Erik; Johansson, Per; Johnert, Sebastian; Johns, Kenneth; Jon-And, Kerstin; Jones, Graham; Jones, Roger; Jones, Tim; Jorge, Pedro; Joseph, John; Juranek, Vojtech; Jussel, Patrick; Kabachenko, Vasily; Kaci, Mohammed; Kaczmarska, Anna; Kado, Marumi; Kagan, Harris; Kagan, Michael; Kaiser, Steffen; Kajomovitz, Enrique; Kalinin, Sergey; Kalinovskaya, Lidia; Kalinowski, Artur; Kama, Sami; Kanaya, Naoko; Kaneda, Michiru; Kantserov, Vadim; Kanzaki, Junichi; Kaplan, Benjamin; Kapliy, Anton; Kaplon, Jan; Kar, Deepak; Karagounis, Michael; Karagoz, Muge; Kartvelishvili, Vakhtang; Karyukhin, Andrey; Kashif, Lashkar; Kasmi, Azzedine; Kass, Richard; Kastanas, Alex; Kastoryano, Michael; Kataoka, Mayuko; Kataoka, Yousuke; Katsoufis, Elias; Katzy, Judith; Kaushik, Venkatesh; Kawagoe, Kiyotomo; Kawamoto, Tatsuo; Kawamura, Gen; Kayl, Manuel; Kayumov, Fred; Kazanin, Vassili; Kazarinov, Makhail; Keates, James Robert; Keeler, Richard; Keener, Paul; Kehoe, Robert; Keil, Markus; Kekelidze, George; Kelly, Marc; Kenyon, Mike; Kepka, Oldrich; Kerschen, Nicolas; Kerševan, Borut Paul; Kersten, Susanne; Kessoku, Kohei; Khakzad, Mohsen; Khalil-zada, Farkhad; Khandanyan, Hovhannes; Khanov, Alexander; Kharchenko, Dmitri; Khodinov, Alexander; Khomich, Andrei; Khoriauli, Gia; Khovanskiy, Nikolai; Khovanskiy, Valery; Khramov, Evgeniy; Khubua, Jemal; Kim, Hyeon Jin; Kim, Min Suk; Kim, Peter; Kim, Shinhong; Kind, Oliver; Kind, Peter; King, Barry; Kirk, Julie; Kirsch, Guillaume; Kirsch, Lawrence; Kiryunin, Andrey; Kisielewska, Danuta; Kittelmann, Thomas; Kiyamura, Hironori; Kladiva, Eduard; Klein, Max; Klein, Uta; Kleinknecht, Konrad; Klemetti, Miika; Klier, Amit; Klimentov, Alexei; Klingenberg, Reiner; Klinkby, Esben; Klioutchnikova, Tatiana; Klok, Peter; Klous, Sander; Kluge, Eike-Erik; Kluge, Thomas; Kluit, Peter; Klute, Markus; Kluth, Stefan; Knecht, Neil; Kneringer, Emmerich; Ko, Byeong Rok; Kobayashi, Tomio; Kobel, Michael; Koblitz, Birger; Kocian, Martin; Kocnar, Antonin; Kodys, Peter; Köneke, Karsten; König, Adriaan; Koenig, Sebastian; Köpke, Lutz; Koetsveld, Folkert; Koevesarki, Peter; Koffas, Thomas; Koffeman, Els; Kohn, Fabian; Kohout, Zdenek; Kohriki, Takashi; Kolanoski, Hermann; Kolesnikov, Vladimir; Koletsou, Iro; Koll, James; Kollar, Daniel; Kolos, Serguei; Kolya, Scott; Komar, Aston; Komaragiri, Jyothsna Rani; Kondo, Takahiko; Kono, Takanori; Konoplich, Rostislav; Konovalov, Serguei; Konstantinidis, Nikolaos; Koperny, Stefan; Korcyl, Krzysztof; Kordas, Kostantinos; Korn, Andreas; Korolkov, Ilya; Korolkova, Elena; Korotkov, Vladislav; Kortner, Oliver; Kortner, Sandra; Kostka, Peter; Kostyukhin, Vadim; Kotov, Serguei; Kotov, Vladislav; Kotov, Konstantin; Kourkoumelis, Christine; Koutsman, Alex; Kowalewski, Robert Victor; Kowalski, Henri; Kowalski, Tadeusz; Kozanecki, Witold; Kozhin, Anatoly; Kral, Vlastimil; Kramarenko, Viktor; Kramberger, Gregor; Krasny, Mieczyslaw Witold; Krasznahorkay, Attila; Kreisel, Arik; Krejci, Frantisek; Kretzschmar, Jan; Krieger, Nina; Krieger, Peter; Kroeninger, Kevin; Kroha, Hubert; Kroll, Joe; Kroseberg, Juergen; Krstic, Jelena; Kruchonak, Uladzimir; Krüger, Hans; Krumshteyn, Zinovii; Kubota, Takashi; Kuehn, Susanne; Kugel, Andreas; Kuhl, Thorsten; Kuhn, Dietmar; Kukhtin, Victor; Kulchitsky, Yuri; Kuleshov, Sergey; Kummer, Christian; Kuna, Marine; Kunkle, Joshua; Kupco, Alexander; Kurashige, Hisaya; Kurata, Masakazu; Kurchaninov, Leonid; Kurochkin, Yurii; Kus, Vlastimil; Kwee, Regina; La Rotonda, Laura; Labbe, Julien; Lacasta, Carlos; Lacava, Francesco; Lacker, Heiko; Lacour, Didier; Lacuesta, Vicente Ramón; Ladygin, Evgueni; Lafaye, Rémi; Laforge, Bertrand; Lagouri, Theodota; Lai, Stanley; Lamanna, Massimo; Lampen, Caleb; Lampl, Walter; Lancon, Eric; Landgraf, Ulrich; Landon, Murrough; Lane, Jenna; Lankford, Andrew; Lanni, Francesco; Lantzsch, Kerstin; Lanza, Agostino; Laplace, Sandrine; Lapoire, Cecile; Laporte, Jean-Francois; Lari, Tommaso; Larner, Aimee; Lassnig, Mario; Laurelli, Paolo; Lavrijsen, Wim; Laycock, Paul; Lazarev, Alexandre; Lazzaro, Alfio; Le Dortz, Olivier; Le Guirriec, Emmanuel; Le Menedeu, Eve; Le Vine, Micheal; Lebedev, Alexander; Lebel, Céline; LeCompte, Thomas; Ledroit-Guillon, Fabienne Agnes Marie; Lee, Hurng-Chun; Lee, Jason; Lee, Shih-Chang; Lefebvre, Michel; Legendre, Marie; LeGeyt, Benjamin; Legger, Federica; Leggett, Charles; Lehmacher, Marc; Lehmann Miotto, Giovanna; Lei, Xiaowen; Leitner, Rupert; Lellouch, Daniel; Lellouch, Jeremie; Lendermann, Victor; Leney, Katharine; Lenz, Tatiana; Lenzen, Georg; Lenzi, Bruno; Leonhardt, Kathrin; Leroy, Claude; Lessard, Jean-Raphael; Lester, Christopher; Leung Fook Cheong, Annabelle; Levêque, Jessica; Levin, Daniel; Levinson, Lorne; Leyton, Michael; Li, Haifeng; Li, Shumin; Li, Xuefei; Liang, Zhihua; Liang, Zhijun; Liberti, Barbara; Lichard, Peter; Lichtnecker, Markus; Lie, Ki; Liebig, Wolfgang; Lilley, Joseph; Lim, Heuijin; Limosani, Antonio; Limper, Maaike; Lin, Simon; Linnemann, James; Lipeles, Elliot; Lipinsky, Lukas; Lipniacka, Anna; Liss, Tony; Lissauer, David; Lister, Alison; Litke, Alan; Liu, Chuanlei; Liu, Dong; Liu, Hao; Liu, Jianbei; Liu, Minghui; Liu, Tiankuan; Liu, Yanwen; Livan, Michele; Lleres, Annick; Lloyd, Stephen; Lobodzinska, Ewelina; Loch, Peter; Lockman, William; Lockwitz, Sarah; Loddenkoetter, Thomas; Loebinger, Fred; Loginov, Andrey; Loh, Chang Wei; Lohse, Thomas; Lohwasser, Kristin; Lokajicek, Milos; Long, Robin Eamonn; Lopes, Lourenco; Lopez Mateos, David; Losada, Marta; Loscutoff, Peter; Lou, Xinchou; Lounis, Abdenour; Loureiro, Karina; Lovas, Lubomir; Love, Jeremy; Love, Peter; Lowe, Andrew; Lu, Feng; Lubatti, Henry; Luci, Claudio; Lucotte, Arnaud; Ludwig, Andreas; Ludwig, Dörthe; Ludwig, Inga; Luehring, Frederick; Luisa, Luca; Lumb, Debra; Luminari, Lamberto; Lund, Esben; Lund-Jensen, Bengt; Lundberg, Björn; Lundberg, Johan; Lundquist, Johan; Lynn, David; Lys, Jeremy; Lytken, Else; Ma, Hong; Ma, Lian Liang; Macana Goia, Jorge Andres; Maccarrone, Giovanni; Macchiolo, Anna; Maček, Boštjan; Machado Miguens, Joana; Mackeprang, Rasmus; Madaras, Ronald; Mader, Wolfgang; Maenner, Reinhard; Maeno, Tadashi; Mättig, Peter; Mättig, Stefan; Magalhaes Martins, Paulo Jorge; Magradze, Erekle; Mahalalel, Yair; Mahboubi, Kambiz; Mahmood, A.; Maiani, Camilla; Maidantchik, Carmen; Maio, Amélia; Majewski, Stephanie; Makida, Yasuhiro; Makouski, Mikhail; Makovec, Nikola; Malecki, Piotr; Malecki, Pawel; Maleev, Victor; Malek, Fairouz; Mallik, Usha; Malon, David; Maltezos, Stavros; Malyshev, Vladimir; Malyukov, Sergei; Mambelli, Marco; Mameghani, Raphael; Mamuzic, Judita; Mandelli, Luciano; Mandić, Igor; Mandrysch, Rocco; Maneira, José; Mangeard, Pierre-Simon; Manjavidze, Ioseb; Manning, Peter; Manousakis-Katsikakis, Arkadios; Mansoulie, Bruno; Mapelli, Alessandro; Mapelli, Livio; March , Luis; Marchand, Jean-Francois; Marchese, Fabrizio; Marchiori, Giovanni; Marcisovsky, Michal; Marino, Christopher; Marroquim, Fernando; Marshall, Zach; Marti-Garcia, Salvador; Martin, Alex; Martin, Andrew; Martin, Brian; Martin, Brian; Martin, Franck Francois; Martin, Jean-Pierre; Martin, Tim; Martin dit Latour, Bertrand; Martinez, Mario; Martinez Outschoorn, Verena; Martini, Agnese; Martyniuk, Alex; Marzano, Francesco; Marzin, Antoine; Masetti, Lucia; Mashimo, Tetsuro; Mashinistov, Ruslan; Masik, Jiri; Maslennikov, Alexey; Massa, Ignazio; Massol, Nicolas; Mastroberardino, Anna; Masubuchi, Tatsuya; Matricon, Pierre; Matsunaga, Hiroyuki; Matsushita, Takashi; Mattravers, Carly; Maxfield, Stephen; Mayne, Anna; Mazini, Rachid; Mazur, Michael; Mazzanti, Marcello; Mc Donald, Jeffrey; Mc Kee, Shawn Patrick; McCarn, Allison; McCarthy, Robert; McCubbin, Norman; McFarlane, Kenneth; McGlone, Helen; Mchedlidze, Gvantsa; McMahon, Steve; McPherson, Robert; Meade, Andrew; Mechnich, Joerg; Mechtel, Markus; Medinnis, Mike; Meera-Lebbai, Razzak; Meguro, Tatsuma; Mehlhase, Sascha; Mehta, Andrew; Meier, Karlheinz; Meirose, Bernhard; Melachrinos, Constantinos; Mellado Garcia, Bruce Rafael; Mendoza Navas, Luis; Meng, Zhaoxia; Menke, Sven; Meoni, Evelin; Mermod, Philippe; Merola, Leonardo; Meroni, Chiara; Merritt, Frank; Messina, Andrea; Metcalfe, Jessica; Mete, Alaettin Serhan; Meyer, Jean-Pierre; Meyer, Jochen; Meyer, Joerg; Meyer, Thomas Christian; Meyer, W. Thomas; Miao, Jiayuan; Michal, Sebastien; Micu, Liliana; Middleton, Robin; Migas, Sylwia; Mijović, Liza; Mikenberg, Giora; Mikestikova, Marcela; Mikuž, Marko; Miller, David; Mills, Corrinne; Mills, Bill; Milov, Alexander; Milstead, David; Milstein, Dmitry; Minaenko, Andrey; Miñano, Mercedes; Minashvili, Irakli; Mincer, Allen; Mindur, Bartosz; Mineev, Mikhail; Ming, Yao; Mir, Lluisa-Maria; Mirabelli, Giovanni; Misawa, Shigeki; Miscetti, Stefano; Misiejuk, Andrzej; Mitrevski, Jovan; Mitsou, Vasiliki A.; Miyagawa, Paul; Mjörnmark, Jan-Ulf; Mladenov, Dimitar; Moa, Torbjoern; Moed, Shulamit; Moeller, Victoria; Mönig, Klaus; Möser, Nicolas; Mohr, Wolfgang; Mohrdieck-Möck, Susanne; Moles-Valls, Regina; Molina-Perez, Jorge; Monk, James; Monnier, Emmanuel; Montesano, Simone; Monticelli, Fernando; Moore, Roger; Mora Herrera, Clemencia; Moraes, Arthur; Morais, Antonio; Morel, Julien; Morello, Gianfranco; Moreno, Deywis; Moreno Llácer, María; Morettini, Paolo; Morii, Masahiro; Morley, Anthony Keith; Mornacchi, Giuseppe; Morozov, Sergey; Morris, John; Moser, Hans-Guenther; Mosidze, Maia; Moss, Josh; Mount, Richard; Mountricha, Eleni; Mouraviev, Sergei; Moyse, Edward; Mudrinic, Mihajlo; Mueller, Felix; Mueller, James; Mueller, Klemens; Müller, Thomas; Muenstermann, Daniel; Muir, Alex; Munwes, Yonathan; Murillo Garcia, Raul; Murray, Bill; Mussche, Ido; Musto, Elisa; Myagkov, Alexey; Myska, Miroslav; Nadal, Jordi; Nagai, Koichi; Nagano, Kunihiro; Nagasaka, Yasushi; Nairz, Armin Michael; Nakamura, Koji; Nakano, Itsuo; Nakatsuka, Hiroki; Nanava, Gizo; Napier, Austin; Nash, Michael; Nation, Nigel; Nattermann, Till; Naumann, Thomas; Navarro, Gabriela; Nderitu, Simon Kirichu; Neal, Homer; Nebot, Eduardo; Nechaeva, Polina; Negri, Andrea; Negri, Guido; Nelson, Andrew; Nelson, Timothy Knight; Nemecek, Stanislav; Nemethy, Peter; Nepomuceno, Andre Asevedo; Nessi, Marzio; Neubauer, Mark; Neusiedl, Andrea; Neves, Ricardo; Nevski, Pavel; Newcomer, Mitchel; Nickerson, Richard; Nicolaidou, Rosy; Nicolas, Ludovic; Nicoletti, Giovanni; Nicquevert, Bertrand; Niedercorn, Francois; Nielsen, Jason; Nikiforov, Andriy; Nikolaev, Kirill; Nikolic-Audit, Irena; Nikolopoulos, Konstantinos; Nilsen, Henrik; Nilsson, Paul; Nisati, Aleandro; Nishiyama, Tomonori; Nisius, Richard; Nodulman, Lawrence; Nomachi, Masaharu; Nomidis, Ioannis; Nordberg, Markus; Nordkvist, Bjoern; Notz, Dieter; Novakova, Jana; Nozaki, Mitsuaki; Nožička, Miroslav; Nugent, Ian Michael; Nuncio-Quiroz, Adriana-Elizabeth; Nunes Hanninger, Guilherme; Nunnemann, Thomas; Nurse, Emily; O'Neil, Dugan; O'Shea, Val; Oakham, Gerald; Oberlack, Horst; Ochi, Atsuhiko; Oda, Susumu; Odaka, Shigeru; Odier, Jerome; Ogren, Harold; Oh, Alexander; Oh, Seog; Ohm, Christian; Ohshima, Takayoshi; Ohshita, Hidetoshi; Ohsugi, Takashi; Okada, Shogo; Okawa, Hideki; Okumura, Yasuyuki; Okuyama, Toyonobu; Olchevski, Alexander; Oliveira, Miguel Alfonso; Oliveira Damazio, Denis; Oliver, John; Oliver Garcia, Elena; Olivito, Dominick; Olszewski, Andrzej; Olszowska, Jolanta; Omachi, Chihiro; Onofre, António; Onyisi, Peter; Oram, Christopher; Oreglia, Mark; Oren, Yona; Orestano, Domizia; Orlov, Iliya; Oropeza Barrera, Cristina; Orr, Robert; Ortega, Eduardo; Osculati, Bianca; Ospanov, Rustem; Osuna, Carlos; Ottersbach, John; Ould-Saada, Farid; Ouraou, Ahmimed; Ouyang, Qun; Owen, Mark; Owen, Simon; Oyarzun, Alejandro; Ozcan, Veysi Erkcan; Ozone, Kenji; Ozturk, Nurcan; Pacheco Pages, Andres; Padilla Aranda, Cristobal; Paganis, Efstathios; Pahl, Christoph; Paige, Frank; Pajchel, Katarina; Palestini, Sandro; Pallin, Dominique; Palma, Alberto; Palmer, Jody; Pan, Yibin; Panagiotopoulou, Evgenia; Panes, Boris; Panikashvili, Natalia; Panitkin, Sergey; Pantea, Dan; Panuskova, Monika; Paolone, Vittorio; Papadopoulou, Theodora; Park, Su-Jung; Park, Woochun; Parker, Andy; Parker, Sherwood; Parodi, Fabrizio; Parsons, John; Parzefall, Ulrich; Pasqualucci, Enrico; Passeri, Antonio; Pastore, Fernanda; Pastore, Francesca; Pásztor , Gabriella; Pataraia, Sophio; Pater, Joleen; Patricelli, Sergio; Patwa, Abid; Pauly, Thilo; Peak, Lawrence; Pecsy, Martin; Pedraza Morales, Maria Isabel; Peleganchuk, Sergey; Peng, Haiping; Penson, Alexander; Penwell, John; Perantoni, Marcelo; Perez, Kerstin; Perez Codina, Estel; Pérez García-Estañ, María Teresa; Perez Reale, Valeria; Perini, Laura; Pernegger, Heinz; Perrino, Roberto; Persembe, Seda; Perus, Antoine; Peshekhonov, Vladimir; Petersen, Brian; Petersen, Troels; Petit, Elisabeth; Petridou, Chariclia; Petrolo, Emilio; Petrucci, Fabrizio; Petschull, Dennis; Petteni, Michele; Pezoa, Raquel; Phan, Anna; Phillips, Alan; Piacquadio, Giacinto; Piccinini, Maurizio; Piegaia, Ricardo; Pilcher, James; Pilkington, Andrew; Pina, João Antonio; Pinamonti, Michele; Pinfold, James; Pinto, Belmiro; Pizio, Caterina; Placakyte, Ringaile; Plamondon, Mathieu; Pleier, Marc-Andre; Poblaguev, Andrei; Poddar, Sahill; Podlyski, Fabrice; Poffenberger, Paul; Poggioli, Luc; Pohl, Martin; Polci, Francesco; Polesello, Giacomo; Policicchio, Antonio; Polini, Alessandro; Poll, James; Polychronakos, Venetios; Pomeroy, Daniel; Pommès, Kathy; Ponsot, Patrick; Pontecorvo, Ludovico; Pope, Bernard; Popeneciu, Gabriel Alexandru; Popovic, Dragan; Poppleton, Alan; Popule, Jiri; Portell Bueso, Xavier; Porter, Robert; Pospelov, Guennady; Pospisil, Stanislav; Potekhin, Maxim; Potrap, Igor; Potter, Christina; Potter, Christopher; Potter, Keith; Poulard, Gilbert; Poveda, Joaquin; Prabhu, Robindra; Pralavorio, Pascal; Prasad, Srivas; Pravahan, Rishiraj; Pribyl, Lukas; Price, Darren; Price, Lawrence; Prichard, Paul; Prieur, Damien; Primavera, Margherita; Prokofiev, Kirill; Prokoshin, Fedor; Protopopescu, Serban; Proudfoot, James; Prudent, Xavier; Przysiezniak, Helenka; Psoroulas, Serena; Ptacek, Elizabeth; Puigdengoles, Carles; Purdham, John; Purohit, Milind; Puzo, Patrick; Pylypchenko, Yuriy; Qi, Ming; Qian, Jianming; Qian, Weiming; Qin, Zhonghua; Quadt, Arnulf; Quarrie, David; Quayle, William; Quinonez, Fernando; Raas, Marcel; Radeka, Veljko; Radescu, Voica; Radics, Balint; Rador, Tonguc; Ragusa, Francesco; Rahal, Ghita; Rahimi, Amir; Rajagopalan, Srinivasan; Rammensee, Michael; Rammes, Marcus; Rauscher, Felix; Rauter, Emanuel; Raymond, Michel; Read, Alexander Lincoln; Rebuzzi, Daniela; Redelbach, Andreas; Redlinger, George; Reece, Ryan; Reeves, Kendall; Reinherz-Aronis, Erez; Reinsch, Andreas; Reisinger, Ingo; Reljic, Dusan; Rembser, Christoph; Ren, Zhongliang; Renkel, Peter; Rescia, Sergio; Rescigno, Marco; Resconi, Silvia; Resende, Bernardo; Reznicek, Pavel; Rezvani, Reyhaneh; Richards, Alexander; Richards, Ronald; Richter, Robert; Richter-Was, Elzbieta; Ridel, Melissa; Rijpstra, Manouk; Rijssenbeek, Michael; Rimoldi, Adele; Rinaldi, Lorenzo; Rios, Ryan Randy; Riu, Imma; Rizatdinova, Flera; Rizvi, Eram; Roa Romero, Diego Alejandro; Robertson, Steven; Robichaud-Veronneau, Andree; Robinson, Dave; Robinson, James; Robinson, Mary; Robson, Aidan; Rocha de Lima, Jose Guilherme; Roda, Chiara; Roda Dos Santos, Denis; Rodriguez, Diego; Rodriguez Garcia, Yohany; Roe, Shaun; Røhne, Ole; Rojo, Victoria; Rolli, Simona; Romaniouk, Anatoli; Romanov, Victor; Romeo, Gaston; Romero Maltrana, Diego; Roos, Lydia; Ros, Eduardo; Rosati, Stefano; Rosenbaum, Gabriel; Rosselet, Laurent; Rossetti, Valerio; Rossi, Leonardo Paolo; Rotaru, Marina; Rothberg, Joseph; Rousseau, David; Royon, Christophe; Rozanov, Alexander; Rozen, Yoram; Ruan, Xifeng; Ruckert, Benjamin; Ruckstuhl, Nicole; Rud, Viacheslav; Rudolph, Gerald; Rühr, Frederik; Ruggieri, Federico; Ruiz-Martinez, Aranzazu; Rumyantsev, Leonid; Rurikova, Zuzana; Rusakovich, Nikolai; Rutherfoord, John; Ruwiedel, Christoph; Ruzicka, Pavel; Ryabov, Yury; Ryan, Patrick; Rybkin, Grigori; Rzaeva, Sevda; Saavedra, Aldo; Sadrozinski, Hartmut; Sadykov, Renat; Sakamoto, Hiroshi; Salamanna, Giuseppe; Salamon, Andrea; Saleem, Muhammad; Salihagic, Denis; Salnikov, Andrei; Salt, José; Salvachua Ferrando, Belén; Salvatore, Daniela; Salvatore, Pasquale Fabrizio; Salvucci, Antonio; Salzburger, Andreas; Sampsonidis, Dimitrios; Samset, Björn Hallvard; Sandaker, Heidi; Sander, Heinz Georg; Sanders, Michiel; Sandhoff, Marisa; Sandhu, Pawan; Sandstroem, Rikard; Sandvoss, Stephan; Sankey, Dave; Sanny, Bernd; Sansoni, Andrea; Santamarina Rios, Cibran; Santoni, Claudio; Santonico, Rinaldo; Saraiva, João; Sarangi, Tapas; Sarkisyan-Grinbaum, Edward; Sarri, Francesca; Sasaki, Osamu; Sasao, Noboru; Satsounkevitch, Igor; Sauvage, Gilles; Savard, Pierre; Savine, Alexandre; Savinov, Vladimir; Sawyer, Lee; Saxon, David; Says, Louis-Pierre; Sbarra, Carla; Sbrizzi, Antonio; Scannicchio, Diana; Schaarschmidt, Jana; Schacht, Peter; Schäfer, Uli; Schaetzel, Sebastian; Schaffer, Arthur; Schaile, Dorothee; Schamberger, R.~Dean; Schamov, Andrey; Schegelsky, Valery; Scheirich, Daniel; Schernau, Michael; Scherzer, Max; Schiavi, Carlo; Schieck, Jochen; Schioppa, Marco; Schlenker, Stefan; Schmidt, Evelyn; Schmieden, Kristof; Schmitt, Christian; Schmitz, Martin; Schott, Matthias; Schouten, Doug; Schovancova, Jaroslava; Schram, Malachi; Schreiner, Alexander; Schroeder, Christian; Schroer, Nicolai; Schroers, Marcel; Schultes, Joachim; Schultz-Coulon, Hans-Christian; Schumacher, Jan; Schumacher, Markus; Schumm, Bruce; Schune, Philippe; Schwanenberger, Christian; Schwartzman, Ariel; Schwemling, Philippe; Schwienhorst, Reinhard; Schwierz, Rainer; Schwindling, Jerome; Scott, Bill; Searcy, Jacob; Sedykh, Evgeny; Segura, Ester; Seidel, Sally; Seiden, Abraham; Seifert, Frank; Seixas, José; Sekhniaidze, Givi; Seliverstov, Dmitry; Sellden, Bjoern; Semprini-Cesari, Nicola; Serfon, Cedric; Serin, Laurent; Seuster, Rolf; Severini, Horst; Sevior, Martin; Sfyrla, Anna; Shabalina, Elizaveta; Shamim, Mansoora; Shan, Lianyou; Shank, James; Shao, Qi Tao; Shapiro, Marjorie; Shatalov, Pavel; Shaw, Kate; Sherman, Daniel; Sherwood, Peter; Shibata, Akira; Shimojima, Makoto; Shin, Taeksu; Shmeleva, Alevtina; Shochet, Mel; Shupe, Michael; Sicho, Petr; Sidoti, Antonio; Siegert, Frank; Siegrist, James; Sijacki, Djordje; Silbert, Ohad; Silver, Yiftah; Silverstein, Daniel; Silverstein, Samuel; Simak, Vladislav; Simic, Ljiljana; Simion, Stefan; Simmons, Brinick; Simonyan, Margar; Sinervo, Pekka; Sinev, Nikolai; Sipica, Valentin; Siragusa, Giovanni; Sisakyan, Alexei; Sivoklokov, Serguei; Sjölin, Jörgen; Sjursen, Therese; Skovpen, Kirill; Skubic, Patrick; Slater, Mark; Slavicek, Tomas; Sliwa, Krzysztof; Sloper, John erik; Sluka, Tomas; Smakhtin, Vladimir; Smirnov, Sergei; Smirnov, Yuri; Smirnova, Lidia; Smirnova, Oxana; Smith, Ben Campbell; Smith, Douglas; Smith, Kenway; Smizanska, Maria; Smolek, Karel; Snesarev, Andrei; Snow, Steve; Snow, Joel; Snuverink, Jochem; Snyder, Scott; Soares, Mara; Sobie, Randall; Sodomka, Jaromir; Soffer, Abner; Solans, Carlos; Solar, Michael; Solc, Jaroslav; Solfaroli Camillocci, Elena; Solodkov, Alexander; Solovyanov, Oleg; Soluk, Richard; Sondericker, John; Sopko, Vit; Sopko, Bruno; Sosebee, Mark; Soukharev, Andrey; Spagnolo, Stefania; Spanò, Francesco; Spencer, Edwin; Spighi, Roberto; Spigo, Giancarlo; Spila, Federico; Spiwoks, Ralf; Spousta, Martin; Spreitzer, Teresa; Spurlock, Barry; St. Denis, Richard Dante; Stahl, Thorsten; Stahlman, Jonathan; Stamen, Rainer; Stancu, Stefan Nicolae; Stanecka, Ewa; Stanek, Robert; Stanescu, Cristian; Stapnes, Steinar; Starchenko, Evgeny; Stark, Jan; Staroba, Pavel; Starovoitov, Pavel; Stastny, Jan; Stavina, Pavel; Stavropoulos, Georgios; Steele, Genevieve; Steinbach, Peter; Steinberg, Peter; Stekl, Ivan; Stelzer, Bernd; Stelzer, Harald Joerg; Stelzer-Chilton, Oliver; Stenzel, Hasko; Stevenson, Kyle; Stewart, Graeme; Stockton, Mark; Stoerig, Kathrin; Stoicea, Gabriel; Stonjek, Stefan; Strachota, Pavel; Stradling, Alden; Straessner, Arno; Strandberg, Jonas; Strandberg, Sara; Strandlie, Are; Strauss, Michael; Strizenec, Pavol; Ströhmer, Raimund; Strom, David; Stroynowski, Ryszard; Strube, Jan; Stugu, Bjarne; Su, Dong; Soh, Dart-yin; Sugaya, Yorihito; Sugimoto, Takuya; Suhr, Chad; Suk, Michal; Sulin, Vladimir; Sultansoy, Saleh; Sumida, Toshi; Sun, Xiaohu; Sundermann, Jan Erik; Suruliz, Kerim; Sushkov, Serge; Susinno, Giancarlo; Sutton, Mark; Suzuki, Takuya; Suzuki, Yu; Sykora, Ivan; Sykora, Tomas; Szymocha, Tadeusz; Sánchez, Javier; Ta, Duc; Tackmann, Kerstin; Taffard, Anyes; Tafirout, Reda; Taga, Adrian; Takahashi, Yuta; Takai, Helio; Takashima, Ryuichi; Takeda, Hiroshi; Takeshita, Tohru; Talby, Mossadek; Talyshev, Alexey; Tamsett, Matthew; Tanaka, Junichi; Tanaka, Reisaburo; Tanaka, Satoshi; Tanaka, Shuji; Tapprogge, Stefan; Tardif, Dominique; Tarem, Shlomit; Tarrade, Fabien; Tartarelli, Giuseppe Francesco; Tas, Petr; Tasevsky, Marek; Tassi, Enrico; Tatarkhanov, Mous; Taylor, Christopher; Taylor, Frank; Taylor, Geoffrey; Taylor, Ryan P.; Taylor, Wendy; Teixeira-Dias, Pedro; Ten Kate, Herman; Teng, Ping-Kun; Tennenbaum-Katan, Yaniv-David; Terada, Susumu; Terashi, Koji; Terron, Juan; Terwort, Mark; Testa, Marianna; Teuscher, Richard; Thioye, Moustapha; Thoma, Sascha; Thomas, Juergen; Thompson, Stan; Thompson, Emily; Thompson, Peter; Thompson, Paul; Thompson, Ray; Thomson, Evelyn; Thun, Rudolf; Tic, Tomas; Tikhomirov, Vladimir; Tikhonov, Yury; Tipton, Paul; Tique Aires Viegas, Florbela De Jes; Tisserant, Sylvain; Toczek, Barbara; Todorov, Theodore; Todorova-Nova, Sharka; Toggerson, Brokk; Tojo, Junji; Tokár, Stanislav; Tokushuku, Katsuo; Tollefson, Kirsten; Tomasek, Lukas; Tomasek, Michal; Tomoto, Makoto; Tompkins, Lauren; Toms, Konstantin; Tonoyan, Arshak; Topfel, Cyril; Topilin, Nikolai; Torrence, Eric; Torró Pastor, Emma; Toth, Jozsef; Touchard, Francois; Tovey, Daniel; Trefzger, Thomas; Tremblet, Louis; Tricoli, Alesandro; Trigger, Isabel Marian; Trincaz-Duvoid, Sophie; Trinh, Thi Nguyet; Tripiana, Martin; Triplett, Nathan; Trischuk, William; Trivedi, Arjun; Trocmé, Benjamin; Troncon, Clara; Trzupek, Adam; Tsarouchas, Charilaos; Tseng, Jeffrey; Tsiakiris, Menelaos; Tsiareshka, Pavel; Tsionou, Dimitra; Tsipolitis, Georgios; Tsiskaridze, Vakhtang; Tskhadadze, Edisher; Tsukerman, Ilya; Tsulaia, Vakhtang; Tsung, Jieh-Wen; Tsuno, Soshi; Tsybychev, Dmitri; Tuggle, Joseph; Turecek, Daniel; Turk Cakir, Ilkay; Turlay, Emmanuel; Tuts, Michael; Twomey, Matthew Shaun; Tylmad, Maja; Tyndel, Mike; Uchida, Kirika; Ueda, Ikuo; Ugland, Maren; Uhlenbrock, Mathias; Uhrmacher, Michael; Ukegawa, Fumihiko; Unal, Guillaume; Undrus, Alexander; Unel, Gokhan; Unno, Yoshinobu; Urbaniec, Dustin; Urkovsky, Evgeny; Urquijo, Phillip; Urrejola, Pedro; Usai, Giulio; Uslenghi, Massimiliano; Vacavant, Laurent; Vacek, Vaclav; Vachon, Brigitte; Vahsen, Sven; Valente, Paolo; Valentinetti, Sara; Valkar, Stefan; Valladolid Gallego, Eva; Vallecorsa, Sofia; Valls Ferrer, Juan Antonio; Van Berg, Richard; van der Graaf, Harry; van der Kraaij, Erik; van der Poel, Egge; van der Ster, Daniel; van Eldik, Niels; van Gemmeren, Peter; van Kesteren, Zdenko; van Vulpen, Ivo; Vandelli, Wainer; Vaniachine, Alexandre; Vankov, Peter; Vannucci, Francois; Vari, Riccardo; Varnes, Erich; Varouchas, Dimitris; Vartapetian, Armen; Varvell, Kevin; Vasilyeva, Lidia; Vassilakopoulos, Vassilios; Vazeille, Francois; Vellidis, Constantine; Veloso, Filipe; Veneziano, Stefano; Ventura, Andrea; Ventura, Daniel; Venturi, Manuela; Venturi, Nicola; Vercesi, Valerio; Verducci, Monica; Verkerke, Wouter; Vermeulen, Jos; Vetterli, Michel; Vichou, Irene; Vickey, Trevor; Viehhauser, Georg; Villa, Mauro; Villani, Giulio; Villaplana Perez, Miguel; Vilucchi, Elisabetta; Vincter, Manuella; Vinek, Elisabeth; Vinogradov, Vladimir; Viret, Sébastien; Virzi, Joseph; Vitale , Antonio; Vitells, Ofer; Vivarelli, Iacopo; Vives Vaque, Francesc; Vlachos, Sotirios; Vlasak, Michal; Vlasov, Nikolai; Vogel, Adrian; Vokac, Petr; Volpi, Matteo; von der Schmitt, Hans; von Loeben, Joerg; von Radziewski, Holger; von Toerne, Eckhard; Vorobel, Vit; Vorwerk, Volker; Vos, Marcel; Voss, Rudiger; Voss, Thorsten Tobias; Vossebeld, Joost; Vranjes, Nenad; Vranjes Milosavljevic, Marija; Vrba, Vaclav; Vreeswijk, Marcel; Vu Anh, Tuan; Vudragovic, Dusan; Vuillermet, Raphael; Vukotic, Ilija; Wagner, Peter; Walbersloh, Jorg; Walder, James; Walker, Rodney; Walkowiak, Wolfgang; Wall, Richard; Wang, Chiho; Wang, Haichen; Wang, Jin; Wang, Song-Ming; Warburton, Andreas; Ward, Patricia; Warsinsky, Markus; Wastie, Roy; Watkins, Peter; Watson, Alan; Watson, Miriam; Watts, Gordon; Watts, Stephen; Waugh, Anthony; Waugh, Ben; Weber, Marc; Weber, Manuel; Weber, Michele; Weber, Pavel; Weidberg, Anthony; Weingarten, Jens; Weiser, Christian; Wellenstein, Hermann; Wells, Phillippa; Wen, Mei; Wenaus, Torre; Wendler, Shanti; Wengler, Thorsten; Wenig, Siegfried; Wermes, Norbert; Werner, Matthias; Werner, Per; Werth, Michael; Werthenbach, Ulrich; Wessels, Martin; Whalen, Kathleen; White, Andrew; White, Martin; White, Sebastian; Whitehead, Samuel Robert; Whiteson, Daniel; Whittington, Denver; Wicek, Francois; Wicke, Daniel; Wickens, Fred; Wiedenmann, Werner; Wielers, Monika; Wienemann, Peter; Wiglesworth, Craig; Wiik, Liv Antje Mari; Wildauer, Andreas; Wildt, Martin Andre; Wilkens, Henric George; Williams, Eric; Williams, Hugh; Willocq, Stephane; Wilson, John; Wilson, Michael Galante; Wilson, Alan; Wingerter-Seez, Isabelle; Winklmeier, Frank; Wittgen, Matthias; Wolter, Marcin Wladyslaw; Wolters, Helmut; Wosiek, Barbara; Wotschack, Jorg; Woudstra, Martin; Wraight, Kenneth; Wright, Catherine; Wright, Dennis; Wrona, Bozydar; Wu, Sau Lan; Wu, Xin; Wulf, Evan; Wynne, Benjamin; Xaplanteris, Leonidas; Xella, Stefania; Xie, Song; Xu, Da; Xu, Neng; Yamada, Miho; Yamamoto, Akira; Yamamoto, Kyoko; Yamamoto, Shimpei; Yamamura, Taiki; Yamaoka, Jared; Yamazaki, Takayuki; Yamazaki, Yuji; Yan, Zhen; Yang, Haijun; Yang, Un-Ki; Yang, Zhaoyu; Yao, Weiming; Yao, Yushu; Yasu, Yoshiji; Ye, Jingbo; Ye, Shuwei; Yilmaz, Metin; Yoosoofmiya, Reza; Yorita, Kohei; Yoshida, Riktura; Young, Charles; Youssef, Saul; Yu, Dantong; Yu, Jaehoon; Yuan, Li; Yurkewicz, Adam; Zaidan, Remi; Zaitsev, Alexander; Zajacova, Zuzana; Zambrano, Valentina; Zanello, Lucia; Zaytsev, Alexander; Zeitnitz, Christian; Zeller, Michael; Zemla, Andrzej; Zendler, Carolin; Zenin, Oleg; Ženiš, Tibor; Zenonos, Zenonas; Zenz, Seth; Zerwas, Dirk; Zevi della Porta, Giovanni; Zhan, Zhichao; Zhang, Huaqiao; Zhang, Jinlong; Zhang, Qizhi; Zhang, Xueyao; Zhao, Long; Zhao, Tianchi; Zhao, Zhengguo; Zhemchugov, Alexey; Zhong, Jiahang; Zhou, Bing; Zhou, Ning; Zhou, Yue; Zhu, Cheng Guang; Zhu, Hongbo; Zhu, Yingchun; Zhuang, Xuai; Zhuravlov, Vadym; Zimmermann, Robert; Zimmermann, Simone; Zimmermann, Stephanie; Ziolkowski, Michael; Živković, Lidija; Zobernig, Georg; Zoccoli, Antonio; zur Nedden, Martin; Zutshi, Vishnu

    2010-01-01

    The simulation software for the ATLAS Experiment at the Large Hadron Collider is being used for large-scale production of events on the LHC Computing Grid. This simulation requires many components, from the generators that simulate particle collisions, through packages simulating the response of the various detectors and triggers. All of these components come together under the ATLAS simulation infrastructure. In this paper, that infrastructure is discussed, including that supporting the detector description, interfacing the event generation, and combining the GEANT4 simulation of the response of the individual detectors. Also described are the tools allowing the software validation, performance testing, and the validation of the simulated output against known physics processes.

  9. The ATLAS Simulation Infrastructure

    Science.gov (United States)

    Aad, G.; Abbott, B.; Abdallah, J.; Abdelalim, A. A.; Abdesselam, A.; Abdinov, O.; Abi, B.; Abolins, M.; Abramowicz, H.; Abreu, H.; Acharya, B. S.; Adams, D. L.; Addy, T. N.; Adelman, J.; Adorisio, C.; Adragna, P.; Adye, T.; Aefsky, S.; Aguilar-Saavedra, J. A.; Aharrouche, M.; Ahlen, S. P.; Ahles, F.; Ahmad, A.; Ahmed, H.; Ahsan, M.; Aielli, G.; Akdogan, T.; Åkesson, T. P. A.; Akimoto, G.; Akimov, A. V.; Aktas, A.; Alam, M. S.; Alam, M. A.; Albrand, S.; Aleksa, M.; Aleksandrov, I. N.; Alexa, C.; Alexander, G.; Alexandre, G.; Alexopoulos, T.; Alhroob, M.; Aliev, M.; Alimonti, G.; Alison, J.; Aliyev, M.; Allport, P. P.; Allwood-Spiers, S. E.; Almond, J.; Aloisio, A.; Alon, R.; Alonso, A.; Alviggi, M. G.; Amako, K.; Amelung, C.; Amorim, A.; Amorós, G.; Amram, N.; Anastopoulos, C.; Andeen, T.; Anders, C. F.; Anderson, K. J.; Andreazza, A.; Andrei, V.; Anduaga, X. S.; Angerami, A.; Anghinolfi, F.; Anjos, N.; Annovi, A.; Antonaki, A.; Antonelli, M.; Antonelli, S.; Antos, J.; Antunovic, B.; Anulli, F.; Aoun, S.; Arabidze, G.; Aracena, I.; Arai, Y.; Arce, A. T. H.; Archambault, J. P.; Arfaoui, S.; Arguin, J.-F.; Argyropoulos, T.; Arik, M.; Armbruster, A. J.; Arnaez, O.; Arnault, C.; Artamonov, A.; Arutinov, D.; Asai, M.; Asai, S.; Asfandiyarov, R.; Ask, S.; Åsman, B.; Asner, D.; Asquith, L.; Assamagan, K.; Astbury, A.; Astvatsatourov, A.; Atoian, G.; Auerbach, B.; Augsten, K.; Aurousseau, M.; Austin, N.; Avolio, G.; Avramidou, R.; Axen, D.; Ay, C.; Azuelos, G.; Azuma, Y.; Baak, M. A.; Bach, A. M.; Bachacou, H.; Bachas, K.; Backes, M.; Badescu, E.; Bagnaia, P.; Bai, Y.; Bain, T.; Baines, J. T.; Baker, O. K.; Baker, M. D.; Baker, S.; Baltasar Dos Santos Pedrosa, F.; Banas, E.; Banerjee, P.; Banerjee, S.; Banfi, D.; Bangert, A.; Bansal, V.; Baranov, S. P.; Baranov, S.; Barashkou, A.; Barber, T.; Barberio, E. L.; Barberis, D.; Barbero, M.; Bardin, D. Y.; Barillari, T.; Barisonzi, M.; Barklow, T.; Barlow, N.; Barnett, B. M.; Barnett, R. M.; Baroncelli, A.; Barr, A. J.; Barreiro, F.; Barreiro Guimarães da Costa, J.; Barrillon, P.; Bartoldus, R.; Bartsch, D.; Bates, R. L.; Batkova, L.; Batley, J. R.; Battaglia, A.; Battistin, M.; Bauer, F.; Bawa, H. S.; Bazalova, M.; Beare, B.; Beau, T.; Beauchemin, P. H.; Beccherle, R.; Becerici, N.; Bechtle, P.; Beck, G. A.; Beck, H. P.; Beckingham, M.; Becks, K. H.; Beddall, A. J.; Beddall, A.; Bednyakov, V. A.; Bee, C.; Begel, M.; Behar Harpaz, S.; Behera, P. K.; Beimforde, M.; Belanger-Champagne, C.; Bell, P. J.; Bell, W. H.; Bella, G.; Bellagamba, L.; Bellina, F.; Bellomo, M.; Belloni, A.; Belotskiy, K.; Beltramello, O.; Ben Ami, S.; Benary, O.; Benchekroun, D.; Bendel, M.; Benedict, B. H.; Benekos, N.; Benhammou, Y.; Benincasa, G. P.; Benjamin, D. P.; Benoit, M.; Bensinger, J. R.; Benslama, K.; Bentvelsen, S.; Beretta, M.; Berge, D.; Bergeaas Kuutmann, E.; Berger, N.; Berghaus, F.; Berglund, E.; Beringer, J.; Bernat, P.; Bernhard, R.; Bernius, C.; Berry, T.; Bertin, A.; Besana, M. I.; Besson, N.; Bethke, S.; Bianchi, R. M.; Bianco, M.; Biebel, O.; Biesiada, J.; Biglietti, M.; Bilokon, H.; Bindi, M.; Binet, S.; Bingul, A.; Bini, C.; Biscarat, C.; Bitenc, U.; Black, K. M.; Blair, R. E.; Blanchard, J.-B.; Blanchot, G.; Blocker, C.; Blondel, A.; Blum, W.; Blumenschein, U.; Bobbink, G. J.; Bocci, A.; Boehler, M.; Boek, J.; Boelaert, N.; Böser, S.; Bogaerts, J. A.; Bogouch, A.; Bohm, C.; Bohm, J.; Boisvert, V.; Bold, T.; Boldea, V.; Bondarenko, V. G.; Bondioli, M.; Boonekamp, M.; Bordoni, S.; Borer, C.; Borisov, A.; Borissov, G.; Borjanovic, I.; Borroni, S.; Bos, K.; Boscherini, D.; Bosman, M.; Boterenbrood, H.; Bouchami, J.; Boudreau, J.; Bouhova-Thacker, E. V.; Boulahouache, C.; Bourdarios, C.; Boveia, A.; Boyd, J.; Boyko, I. R.; Bozovic-Jelisavcic, I.; Bracinik, J.; Braem, A.; Branchini, P.; Brandenburg, G. W.; Brandt, A.; Brandt, G.; Brandt, O.; Bratzler, U.; Brau, B.; Brau, J. E.; Braun, H. M.; Brelier, B.; Bremer, J.; Brenner, R.; Bressler, S.; Britton, D.; Brochu, F. M.; Brock, I.; Brock, R.; Brodet, E.; Bromberg, C.; Brooijmans, G.; Brooks, W. K.; Brown, G.; Bruckman de Renstrom, P. A.; Bruncko, D.; Bruneliere, R.; Brunet, S.; Bruni, A.; Bruni, G.; Bruschi, M.; Bucci, F.; Buchanan, J.; Buchholz, P.; Buckley, A. G.; Budagov, I. A.; Budick, B.; Büscher, V.; Bugge, L.; Bulekov, O.; Bunse, M.; Buran, T.; Burckhart, H.; Burdin, S.; Burgess, T.; Burke, S.; Busato, E.; Bussey, P.; Buszello, C. P.; Butin, F.; Butler, B.; Butler, J. M.; Buttar, C. M.; Butterworth, J. M.; Byatt, T.; Caballero, J.; Cabrera Urbán, S.; Caforio, D.; Cakir, O.; Calafiura, P.; Calderini, G.; Calfayan, P.; Calkins, R.; Caloba, L. P.; Calvet, D.; Camarri, P.; Cameron, D.; Campana, S.; Campanelli, M.; Canale, V.; Canelli, F.; Canepa, A.; Cantero, J.; Capasso, L.; Capeans Garrido, M. D. M.; Caprini, I.; Caprini, M.; Capua, M.; Caputo, R.; Caramarcu, C.; Cardarelli, R.; Carli, T.; Carlino, G.; Carminati, L.; Caron, B.; Caron, S.; Carrillo Montoya, G. D.; Carron Montero, S.; Carter, A. A.; Carter, J. R.; Carvalho, J.; Casadei, D.; Casado, M. P.; Cascella, M.; Castaneda Hernandez, A. M.; Castaneda-Miranda, E.; Castillo Gimenez, V.; Castro, N. F.; Cataldi, G.; Catinaccio, A.; Catmore, J. R.; Cattai, A.; Cattani, G.; Caughron, S.; Cauz, D.; Cavalleri, P.; Cavalli, D.; Cavalli-Sforza, M.; Cavasinni, V.; Ceradini, F.; Cerqueira, A. S.; Cerri, A.; Cerrito, L.; Cerutti, F.; Cetin, S. A.; Chafaq, A.; Chakraborty, D.; Chan, K.; Chapman, J. D.; Chapman, J. W.; Chareyre, E.; Charlton, D. G.; Chavda, V.; Cheatham, S.; Chekanov, S.; Chekulaev, S. V.; Chelkov, G. A.; Chen, H.; Chen, S.; Chen, X.; Cheplakov, A.; Chepurnov, V. F.; Cherkaoui El Moursli, R.; Tcherniatine, V.; Chesneanu, D.; Cheu, E.; Cheung, S. L.; Chevalier, L.; Chevallier, F.; Chiarella, V.; Chiefari, G.; Chikovani, L.; Childers, J. T.; Chilingarov, A.; Chiodini, G.; Chizhov, V.; Choudalakis, G.; Chouridou, S.; Christidi, I. A.; Christov, A.; Chromek-Burckhart, D.; Chu, M. L.; Chudoba, J.; Ciapetti, G.; Ciftci, A. K.; Ciftci, R.; Cinca, D.; Cindro, V.; Ciobotaru, M. D.; Ciocca, C.; Ciocio, A.; Cirilli, M.; Citterio, M.; Clark, A.; Clark, P. J.; Cleland, W.; Clemens, J. C.; Clement, B.; Clement, C.; Coadou, Y.; Cobal, M.; Coccaro, A.; Cochran, J.; Coggeshall, J.; Cogneras, E.; Colijn, A. P.; Collard, C.; Collins, N. J.; Collins-Tooth, C.; Collot, J.; Colon, G.; Conde Muiño, P.; Coniavitis, E.; Consonni, M.; Constantinescu, S.; Conta, C.; Conventi, F.; Cooke, M.; Cooper, B. D.; Cooper-Sarkar, A. M.; Cooper-Smith, N. J.; Copic, K.; Cornelissen, T.; Corradi, M.; Corriveau, F.; Corso-Radu, A.; Cortes-Gonzalez, A.; Cortiana, G.; Costa, G.; Costa, M. J.; Costanzo, D.; Costin, T.; Côté, D.; Coura Torres, R.; Courneyea, L.; Cowan, G.; Cowden, C.; Cox, B. E.; Cranmer, K.; Cranshaw, J.; Cristinziani, M.; Crosetti, G.; Crupi, R.; Crépé-Renaudin, S.; Cuenca Almenar, C.; Cuhadar Donszelmann, T.; Curatolo, M.; Curtis, C. J.; Cwetanski, P.; Czyczula, Z.; D'Auria, S.; D'Onofrio, M.; D'Orazio, A.; da Via, C.; Dabrowski, W.; Dai, T.; Dallapiccola, C.; Dallison, S. J.; Daly, C. H.; Dam, M.; Danielsson, H. O.; Dannheim, D.; Dao, V.; Darbo, G.; Darlea, G. L.; Davey, W.; Davidek, T.; Davidson, N.; Davidson, R.; Davies, M.; Davison, A. R.; Dawson, I.; Daya, R. K.; de, K.; de Asmundis, R.; de Castro, S.; de Castro Faria Salgado, P. E.; de Cecco, S.; de Graat, J.; de Groot, N.; de Jong, P.; de Mora, L.; de Oliveira Branco, M.; de Pedis, D.; de Salvo, A.; de Sanctis, U.; de Santo, A.; de Vivie de Regie, J. B.; de Zorzi, G.; Dean, S.; Dedovich, D. V.; Degenhardt, J.; Dehchar, M.; Del Papa, C.; Del Peso, J.; Del Prete, T.; Dell'Acqua, A.; Dell'Asta, L.; Della Pietra, M.; Della Volpe, D.; Delmastro, M.; Delsart, P. A.; Deluca, C.; Demers, S.; Demichev, M.; Demirkoz, B.; Deng, J.; Deng, W.; Denisov, S. P.; Derkaoui, J. E.; Derue, F.; Dervan, P.; Desch, K.; Deviveiros, P. O.; Dewhurst, A.; Dewilde, B.; Dhaliwal, S.; Dhullipudi, R.; di Ciaccio, A.; di Ciaccio, L.; di Domenico, A.; di Girolamo, A.; di Girolamo, B.; di Luise, S.; di Mattia, A.; di Nardo, R.; di Simone, A.; di Sipio, R.; Diaz, M. A.; Diblen, F.; Diehl, E. B.; Dietrich, J.; Dietzsch, T. A.; Diglio, S.; Dindar Yagci, K.; Dingfelder, J.; Dionisi, C.; Dita, P.; Dita, S.; Dittus, F.; Djama, F.; Djilkibaev, R.; Djobava, T.; Do Vale, M. A. B.; Do Valle Wemans, A.; Doan, T. K. O.; Dobos, D.; Dobson, E.; Dobson, M.; Doglioni, C.; Doherty, T.; Dolejsi, J.; Dolenc, I.; Dolezal, Z.; Dolgoshein, B. A.; Dohmae, T.; Donega, M.; Donini, J.; Dopke, J.; Doria, A.; Dos Anjos, A.; Dotti, A.; Dova, M. T.; Doxiadis, A.; Doyle, A. T.; Drasal, Z.; Dris, M.; Dubbert, J.; Duchovni, E.; Duckeck, G.; Dudarev, A.; Dudziak, F.; Dührssen, M.; Duflot, L.; Dufour, M.-A.; Dunford, M.; Duran Yildiz, H.; Dushkin, A.; Duxfield, R.; Dwuznik, M.; Düren, M.; Ebenstein, W. L.; Ebke, J.; Eckweiler, S.; Edmonds, K.; Edwards, C. A.; Egorov, K.; Ehrenfeld, W.; Ehrich, T.; Eifert, T.; Eigen, G.; Einsweiler, K.; Eisenhandler, E.; Ekelof, T.; El Kacimi, M.; Ellert, M.; Elles, S.; Ellinghaus, F.; Ellis, K.; Ellis, N.; Elmsheuser, J.; Elsing, M.; Emeliyanov, D.; Engelmann, R.; Engl, A.; Epp, B.; Eppig, A.; Erdmann, J.; Ereditato, A.; Eriksson, D.; Ermoline, I.; Ernst, J.; Ernst, M.; Ernwein, J.; Errede, D.; Errede, S.; Ertel, E.; Escalier, M.; Escobar, C.; Espinal Curull, X.; Esposito, B.; Etienvre, A. I.; Etzion, E.; Evans, H.; Fabbri, L.; Fabre, C.; Facius, K.; Fakhrutdinov, R. M.; Falciano, S.; Fang, Y.; Fanti, M.; Farbin, A.; Farilla, A.; Farley, J.; Farooque, T.; Farrington, S. M.; Farthouat, P.; Fassnacht, P.; Fassouliotis, D.; Fatholahzadeh, B.; Fayard, L.; Fayette, F.; Febbraro, R.; Federic, P.; Fedin, O. L.; Fedorko, W.; Feligioni, L.; Felzmann, C. U.; Feng, C.; Feng, E. J.; Fenyuk, A. B.; Ferencei, J.; Ferland, J.; Fernandes, B.; Fernando, W.; Ferrag, S.; Ferrando, J.; Ferrara, V.; Ferrari, A.; Ferrari, P.; Ferrari, R.; Ferrer, A.; Ferrer, M. L.; Ferrere, D.; Ferretti, C.; Fiascaris, M.; Fiedler, F.; Filipčič, A.; Filippas, A.; Filthaut, F.; Fincke-Keeler, M.; Fiolhais, M. C. N.; Fiorini, L.; Firan, A.; Fischer, G.; Fisher, M. J.; Flechl, M.; Fleck, I.; Fleckner, J.; Fleischmann, P.; Fleischmann, S.; Flick, T.; Flores Castillo, L. R.; Flowerdew, M. J.; Fonseca Martin, T.; Formica, A.; Forti, A.; Fortin, D.; Fournier, D.; Fowler, A. J.; Fowler, K.; Fox, H.; Francavilla, P.; Franchino, S.; Francis, D.; Franklin, M.; Franz, S.; Fraternali, M.; Fratina, S.; Freestone, J.; French, S. T.; Froeschl, R.; Froidevaux, D.; Frost, J. A.; Fukunaga, C.; Fullana Torregrosa, E.; Fuster, J.; Gabaldon, C.; Gabizon, O.; Gadfort, T.; Gadomski, S.; Gagliardi, G.; Gagnon, P.; Galea, C.; Gallas, E. J.; Gallas, M. V.; Gallo, V.; Gallop, B. J.; Gallus, P.; Galyaev, E.; Gan, K. K.; Gao, Y. S.; Gaponenko, A.; Garcia-Sciveres, M.; García, C.; García Navarro, J. E.; Gardner, R. W.; Garelli, N.; Garitaonandia, H.; Garonne, V.; Gatti, C.; Gaudio, G.; Gautard, V.; Gauzzi, P.; Gavrilenko, I. L.; Gay, C.; Gaycken, G.; Gazis, E. N.; Ge, P.; Gee, C. N. P.; Geich-Gimbel, Ch.; Gellerstedt, K.; Gemme, C.; Genest, M. H.; Gentile, S.; Georgatos, F.; George, S.; Gershon, A.; Ghazlane, H.; Ghodbane, N.; Giacobbe, B.; Giagu, S.; Giakoumopoulou, V.; Giangiobbe, V.; Gianotti, F.; Gibbard, B.; Gibson, A.; Gibson, S. M.; Gilbert, L. M.; Gilchriese, M.; Gilewsky, V.; Gingrich, D. M.; Ginzburg, J.; Giokaris, N.; Giordani, M. P.; Giordano, R.; Giorgi, F. M.; Giovannini, P.; Giraud, P. F.; Girtler, P.; Giugni, D.; Giusti, P.; Gjelsten, B. K.; Gladilin, L. K.; Glasman, C.; Glazov, A.; Glitza, K. W.; Glonti, G. L.; Godfrey, J.; Godlewski, J.; Goebel, M.; Göpfert, T.; Goeringer, C.; Gössling, C.; Göttfert, T.; Goggi, V.; Goldfarb, S.; Goldin, D.; Golling, T.; Gomes, A.; Gomez Fajardo, L. S.; Gonçalo, R.; Gonella, L.; Gong, C.; González de La Hoz, S.; Gonzalez Silva, M. L.; Gonzalez-Sevilla, S.; Goodson, J. J.; Goossens, L.; Gordon, H. A.; Gorelov, I.; Gorfine, G.; Gorini, B.; Gorini, E.; Gorišek, A.; Gornicki, E.; Gosdzik, B.; Gosselink, M.; Gostkin, M. I.; Gough Eschrich, I.; Gouighri, M.; Goujdami, D.; Goulette, M. P.; Goussiou, A. G.; Goy, C.; Grabowska-Bold, I.; Grafström, P.; Grahn, K.-J.; Grancagnolo, S.; Grassi, V.; Gratchev, V.; Grau, N.; Gray, H. M.; Gray, J. A.; Graziani, E.; Green, B.; Greenshaw, T.; Greenwood, Z. D.; Gregor, I. M.; Grenier, P.; Griesmayer, E.; Griffiths, J.; Grigalashvili, N.; Grillo, A. A.; Grimm, K.; Grinstein, S.; Grishkevich, Y. V.; Groh, M.; Groll, M.; Gross, E.; Grosse-Knetter, J.; Groth-Jensen, J.; Grybel, K.; Guicheney, C.; Guida, A.; Guillemin, T.; Guler, H.; Gunther, J.; Guo, B.; Gupta, A.; Gusakov, Y.; Gutierrez, A.; Gutierrez, P.; Guttman, N.; Gutzwiller, O.; Guyot, C.; Gwenlan, C.; Gwilliam, C. B.; Haas, A.; Haas, S.; Haber, C.; Hadavand, H. K.; Hadley, D. R.; Haefner, P.; Härtel, R.; Hajduk, Z.; Hakobyan, H.; Haller, J.; Hamacher, K.; Hamilton, A.; Hamilton, S.; Han, L.; Hanagaki, K.; Hance, M.; Handel, C.; Hanke, P.; Hansen, J. R.; Hansen, J. B.; Hansen, J. D.; Hansen, P. H.; Hansl-Kozanecka, T.; Hansson, P.; Hara, K.; Hare, G. A.; Harenberg, T.; Harrington, R. D.; Harris, O. M.; Harrison, K.; Hartert, J.; Hartjes, F.; Harvey, A.; Hasegawa, S.; Hasegawa, Y.; Hashemi, K.; Hassani, S.; Haug, S.; Hauschild, M.; Hauser, R.; Havranek, M.; Hawkes, C. M.; Hawkings, R. J.; Hayakawa, T.; Hayward, H. S.; Haywood, S. J.; Head, S. J.; Hedberg, V.; Heelan, L.; Heim, S.; Heinemann, B.; Heisterkamp, S.; Helary, L.; Heller, M.; Hellman, S.; Helsens, C.; Hemperek, T.; Henderson, R. C. W.; Henke, M.; Henrichs, A.; Henriques Correia, A. M.; Henrot-Versille, S.; Hensel, C.; Henß, T.; Hernández Jiménez, Y.; Hershenhorn, A. D.; Herten, G.; Hertenberger, R.; Hervas, L.; Hessey, N. P.; Higón-Rodriguez, E.; Hill, J. C.; Hiller, K. H.; Hillert, S.; Hillier, S. J.; Hinchliffe, I.; Hines, E.; Hirose, M.; Hirsch, F.; Hirschbuehl, D.; Hobbs, J.; Hod, N.; Hodgkinson, M. C.; Hodgson, P.; Hoecker, A.; Hoeferkamp, M. R.; Hoffman, J.; Hoffmann, D.; Hohlfeld, M.; Holy, T.; Holzbauer, J. L.; Homma, Y.; Horazdovsky, T.; Hori, T.; Horn, C.; Horner, S.; Horvat, S.; Hostachy, J.-Y.; Hou, S.; Hoummada, A.; Howe, T.; Hrivnac, J.; Hryn'ova, T.; Hsu, P. J.; Hsu, S.-C.; Huang, G. S.; Hubacek, Z.; Hubaut, F.; Huegging, F.; Hughes, E. W.; Hughes, G.; Hurwitz, M.; Husemann, U.; Huseynov, N.; Huston, J.; Huth, J.; Iacobucci, G.; Iakovidis, G.; Ibragimov, I.; Iconomidou-Fayard, L.; Idarraga, J.; Iengo, P.; Igonkina, O.; Ikegami, Y.; Ikeno, M.; Ilchenko, Y.; Iliadis, D.; Ince, T.; Ioannou, P.; Iodice, M.; Irles Quiles, A.; Ishikawa, A.; Ishino, M.; Ishmukhametov, R.; Isobe, T.; Issakov, V.; Issever, C.; Istin, S.; Itoh, Y.; Ivashin, A. V.; Iwanski, W.; Iwasaki, H.; Izen, J. M.; Izzo, V.; Jackson, B.; Jackson, J. N.; Jackson, P.; Jaekel, M. R.; Jain, V.; Jakobs, K.; Jakobsen, S.; Jakubek, J.; Jana, D. K.; Jansen, E.; Jantsch, A.; Janus, M.; Jared, R. C.; Jarlskog, G.; Jeanty, L.; Jen-La Plante, I.; Jenni, P.; Jez, P.; Jézéquel, S.; Ji, W.; Jia, J.; Jiang, Y.; Jimenez Belenguer, M.; Jin, S.; Jinnouchi, O.; Joffe, D.; Johansen, M.; Johansson, K. E.; Johansson, P.; Johnert, S.; Johns, K. A.; Jon-And, K.; Jones, G.; Jones, R. W. L.; Jones, T. J.; Jorge, P. M.; Joseph, J.; Juranek, V.; Jussel, P.; Kabachenko, V. V.; Kaci, M.; Kaczmarska, A.; Kado, M.; Kagan, H.; Kagan, M.; Kaiser, S.; Kajomovitz, E.; Kalinin, S.; Kalinovskaya, L. V.; Kalinowski, A.; Kama, S.; Kanaya, N.; Kaneda, M.; Kantserov, V. A.; Kanzaki, J.; Kaplan, B.; Kapliy, A.; Kaplon, J.; Kar, D.; Karagounis, M.; Karagoz Unel, M.; Kartvelishvili, V.; Karyukhin, A. N.; Kashif, L.; Kasmi, A.; Kass, R. D.; Kastanas, A.; Kastoryano, M.; Kataoka, M.; Kataoka, Y.; Katsoufis, E.; Katzy, J.; Kaushik, V.; Kawagoe, K.; Kawamoto, T.; Kawamura, G.; Kayl, M. S.; Kayumov, F.; Kazanin, V. A.; Kazarinov, M. Y.; Keates, J. R.; Keeler, R.; Keener, P. T.; Kehoe, R.; Keil, M.; Kekelidze, G. D.; Kelly, M.; Kenyon, M.; Kepka, O.; Kerschen, N.; Kerševan, B. P.; Kersten, S.; Kessoku, K.; Khakzad, M.; Khalil-Zada, F.; Khandanyan, H.; Khanov, A.; Kharchenko, D.; Khodinov, A.; Khomich, A.; Khoriauli, G.; Khovanskiy, N.; Khovanskiy, V.; Khramov, E.; Khubua, J.; Kim, H.; Kim, M. S.; Kim, P. C.; Kim, S. H.; Kind, O.; Kind, P.; King, B. T.; Kirk, J.; Kirsch, G. P.; Kirsch, L. E.; Kiryunin, A. E.; Kisielewska, D.; Kittelmann, T.; Kiyamura, H.; Kladiva, E.; Klein, M.; Klein, U.; Kleinknecht, K.; Klemetti, M.; Klier, A.; Klimentov, A.; Klingenberg, R.; Klinkby, E. B.; Klioutchnikova, T.; Klok, P. F.; Klous, S.; Kluge, E.-E.; Kluge, T.; Kluit, P.; Klute, M.; Kluth, S.; Knecht, N. S.; Kneringer, E.; Ko, B. R.; Kobayashi, T.; Kobel, M.; Koblitz, B.; Kocian, M.; Kocnar, A.; Kodys, P.; Köneke, K.; König, A. C.; Koenig, S.; Köpke, L.; Koetsveld, F.; Koevesarki, P.; Koffas, T.; Koffeman, E.; Kohn, F.; Kohout, Z.; Kohriki, T.; Kolanoski, H.; Kolesnikov, V.; Koletsou, I.; Koll, J.; Kollar, D.; Kolos, S.; Kolya, S. D.; Komar, A. A.; Komaragiri, J. R.; Kondo, T.; Kono, T.; Konoplich, R.; Konovalov, S. P.; Konstantinidis, N.; Koperny, S.; Korcyl, K.; Kordas, K.; Korn, A.; Korolkov, I.; Korolkova, E. V.; Korotkov, V. A.; Kortner, O.; Kostka, P.; Kostyukhin, V. V.; Kotov, S.; Kotov, V. M.; Kotov, K. Y.; Kourkoumelis, C.; Koutsman, A.; Kowalewski, R.; Kowalski, H.; Kowalski, T. Z.; Kozanecki, W.; Kozhin, A. S.; Kral, V.; Kramarenko, V. A.; Kramberger, G.; Krasny, M. W.; Krasznahorkay, A.; Kreisel, A.; Krejci, F.; Kretzschmar, J.; Krieger, N.; Krieger, P.; Kroeninger, K.; Kroha, H.; Kroll, J.; Kroseberg, J.; Krstic, J.; Kruchonak, U.; Krüger, H.; Krumshteyn, Z. V.; Kubota, T.; Kuehn, S.; Kugel, A.; Kuhl, T.; Kuhn, D.; Kukhtin, V.; Kulchitsky, Y.; Kuleshov, S.; Kummer, C.; Kuna, M.; Kunkle, J.; Kupco, A.; Kurashige, H.; Kurata, M.; Kurchaninov, L. L.; Kurochkin, Y. A.; Kus, V.; Kwee, R.; La Rotonda, L.; Labbe, J.; Lacasta, C.; Lacava, F.; Lacker, H.; Lacour, D.; Lacuesta, V. R.; Ladygin, E.; Lafaye, R.; Laforge, B.; Lagouri, T.; Lai, S.; Lamanna, M.; Lampen, C. L.; Lampl, W.; Lancon, E.; Landgraf, U.; Landon, M. P. J.; Lane, J. L.; Lankford, A. J.; Lanni, F.; Lantzsch, K.; Lanza, A.; Laplace, S.; Lapoire, C.; Laporte, J. F.; Lari, T.; Larner, A.; Lassnig, M.; Laurelli, P.; Lavrijsen, W.; Laycock, P.; Lazarev, A. B.; Lazzaro, A.; Le Dortz, O.; Le Guirriec, E.; Le Menedeu, E.; Le Vine, M.; Lebedev, A.; Lebel, C.; Lecompte, T.; Ledroit-Guillon, F.; Lee, H.; Lee, J. S. H.; Lee, S. C.; Lefebvre, M.; Legendre, M.; Legeyt, B. C.; Legger, F.; Leggett, C.; Lehmacher, M.; Lehmann Miotto, G.; Lei, X.; Leitner, R.; Lellouch, D.; Lellouch, J.; Lendermann, V.; Leney, K. J. C.; Lenz, T.; Lenzen, G.; Lenzi, B.; Leonhardt, K.; Leroy, C.; Lessard, J.-R.; Lester, C. G.; Leung Fook Cheong, A.; Levêque, J.; Levin, D.; Levinson, L. J.; Leyton, M.; Li, H.; Li, S.; Li, X.; Liang, Z.; Liang, Z.; Liberti, B.; Lichard, P.; Lichtnecker, M.; Lie, K.; Liebig, W.; Lilley, J. N.; Lim, H.; Limosani, A.; Limper, M.; Lin, S. C.; Linnemann, J. T.; Lipeles, E.; Lipinsky, L.; Lipniacka, A.; Liss, T. M.; Lissauer, D.; Lister, A.; Litke, A. M.; Liu, C.; Liu, D.; Liu, H.; Liu, J. B.; Liu, M.; Liu, T.; Liu, Y.; Livan, M.; Lleres, A.; Lloyd, S. L.; Lobodzinska, E.; Loch, P.; Lockman, W. S.; Lockwitz, S.; Loddenkoetter, T.; Loebinger, F. K.; Loginov, A.; Loh, C. W.; Lohse, T.; Lohwasser, K.; Lokajicek, M.; Long, R. E.; Lopes, L.; Lopez Mateos, D.; Losada, M.; Loscutoff, P.; Lou, X.; Lounis, A.; Loureiro, K. F.; Lovas, L.; Love, J.; Love, P. A.; Lowe, A. J.; Lu, F.; Lubatti, H. J.; Luci, C.; Lucotte, A.; Ludwig, A.; Ludwig, D.; Ludwig, I.; Luehring, F.; Luisa, L.; Lumb, D.; Luminari, L.; Lund, E.; Lund-Jensen, B.; Lundberg, B.; Lundberg, J.; Lundquist, J.; Lynn, D.; Lys, J.; Lytken, E.; Ma, H.; Ma, L. L.; Macana Goia, J. A.; Maccarrone, G.; Macchiolo, A.; Maček, B.; Machado Miguens, J.; Mackeprang, R.; Madaras, R. J.; Mader, W. F.; Maenner, R.; Maeno, T.; Mättig, P.; Mättig, S.; Magalhaes Martins, P. J.; Magradze, E.; Mahalalel, Y.; Mahboubi, K.; Mahmood, A.; Maiani, C.; Maidantchik, C.; Maio, A.; Majewski, S.; Makida, Y.; Makouski, M.; Makovec, N.; Malecki, Pa.; Malecki, P.; Maleev, V. P.; Malek, F.; Mallik, U.; Malon, D.; Maltezos, S.; Malyshev, V.; Malyukov, S.; Mambelli, M.; Mameghani, R.; Mamuzic, J.; Mandelli, L.; Mandić, I.; Mandrysch, R.; Maneira, J.; Mangeard, P. S.; Manjavidze, I. D.; Manning, P. M.; Manousakis-Katsikakis, A.; Mansoulie, B.; Mapelli, A.; Mapelli, L.; March, L.; Marchand, J. F.; Marchese, F.; Marchiori, G.; Marcisovsky, M.; Marino, C. P.; Marroquim, F.; Marshall, Z.; Marti-Garcia, S.; Martin, A. J.; Martin, A. J.; Martin, B.; Martin, B.; Martin, F. F.; Martin, J. P.; Martin, T. A.; Martin Dit Latour, B.; Martinez, M.; Martinez Outschoorn, V.; Martini, A.; Martyniuk, A. C.; Marzano, F.; Marzin, A.; Masetti, L.; Mashimo, T.; Mashinistov, R.; Masik, J.; Maslennikov, A. L.; Massa, I.; Massol, N.; Mastroberardino, A.; Masubuchi, T.; Matricon, P.; Matsunaga, H.; Matsushita, T.; Mattravers, C.; Maxfield, S. J.; Mayne, A.; Mazini, R.; Mazur, M.; Mazzanti, M.; McDonald, J.; McKee, S. P.; McCarn, A.; McCarthy, R. L.; McCubbin, N. A.; McFarlane, K. W.; McGlone, H.; McHedlidze, G.; McMahon, S. J.; McPherson, R. A.; Meade, A.; Mechnich, J.; Mechtel, M.; Medinnis, M.; Meera-Lebbai, R.; Meguro, T. M.; Mehlhase, S.; Mehta, A.; Meier, K.; Meirose, B.; Melachrinos, C.; Mellado Garcia, B. R.; Mendoza Navas, L.; Meng, Z.; Menke, S.; Meoni, E.; Mermod, P.; Merola, L.; Meroni, C.; Merritt, F. S.; Messina, A. M.; Metcalfe, J.; Mete, A. S.; Meyer, J.-P.; Meyer, J.; Meyer, J.; Meyer, T. C.; Meyer, W. T.; Miao, J.; Michal, S.; Micu, L.; Middleton, R. P.; Migas, S.; Mijović, L.; Mikenberg, G.; Mikestikova, M.; Mikuž, M.; Miller, D. W.; Mills, W. J.; Mills, C. M.; Milov, A.; Milstead, D. A.; Milstein, D.; Minaenko, A. A.; Miñano, M.; Minashvili, I. A.; Mincer, A. I.; Mindur, B.; Mineev, M.; Ming, Y.; Mir, L. M.; Mirabelli, G.; Misawa, S.; Miscetti, S.; Misiejuk, A.; Mitrevski, J.; Mitsou, V. A.; Miyagawa, P. S.; Mjörnmark, J. U.; Mladenov, D.; Moa, T.; Moed, S.; Moeller, V.; Mönig, K.; Möser, N.; Mohr, W.; Mohrdieck-Möck, S.; Moles-Valls, R.; Molina-Perez, J.; Monk, J.; Monnier, E.; Montesano, S.; Monticelli, F.; Moore, R. W.; Mora Herrera, C.; Moraes, A.; Morais, A.; Morel, J.; Morello, G.; Moreno, D.; Moreno Llácer, M.; Morettini, P.; Morii, M.; Morley, A. K.; Mornacchi, G.; Morozov, S. V.; Morris, J. D.; Moser, H. G.; Mosidze, M.; Moss, J.; Mount, R.; Mountricha, E.; Mouraviev, S. V.; Moyse, E. J. W.; Mudrinic, M.; Mueller, F.; Mueller, J.; Mueller, K.; Müller, T. A.; Muenstermann, D.; Muir, A.; Munwes, Y.; Murillo Garcia, R.; Murray, W. J.; Mussche, I.; Musto, E.; Myagkov, A. G.; Myska, M.; Nadal, J.; Nagai, K.; Nagano, K.; Nagasaka, Y.; Nairz, A. M.; Nakamura, K.; Nakano, I.; Nakatsuka, H.; Nanava, G.; Napier, A.; Nash, M.; Nation, N. R.; Nattermann, T.; Naumann, T.; Navarro, G.; Nderitu, S. K.; Neal, H. A.; Nebot, E.; Nechaeva, P.; Negri, A.; Negri, G.; Nelson, A.; Nelson, T. K.; Nemecek, S.; Nemethy, P.; Nepomuceno, A. A.; Nessi, M.; Neubauer, M. S.; Neusiedl, A.; Neves, R. M.; Nevski, P.; Newcomer, F. M.; Nickerson, R. B.; Nicolaidou, R.; Nicolas, L.; Nicoletti, G.; Nicquevert, B.; Niedercorn, F.; Nielsen, J.; Nikiforov, A.; Nikolaev, K.; Nikolic-Audit, I.; Nikolopoulos, K.; Nilsen, H.; Nilsson, P.; Nisati, A.; Nishiyama, T.; Nisius, R.; Nodulman, L.; Nomachi, M.; Nomidis, I.; Nordberg, M.; Nordkvist, B.; Notz, D.; Novakova, J.; Nozaki, M.; Nožička, M.; Nugent, I. M.; Nuncio-Quiroz, A.-E.; Nunes Hanninger, G.; Nunnemann, T.; Nurse, E.; O'Neil, D. C.; O'Shea, V.; Oakham, F. G.; Oberlack, H.; Ochi, A.; Oda, S.; Odaka, S.; Odier, J.; Ogren, H.; Oh, A.; Oh, S. H.; Ohm, C. C.; Ohshima, T.; Ohshita, H.; Ohsugi, T.; Okada, S.; Okawa, H.; Okumura, Y.; Okuyama, T.; Olchevski, A. G.; Oliveira, M.; Oliveira Damazio, D.; Oliver, J.; Oliveira Garcia, E.; Olivito, D.; Olszewski, A.; Olszowska, J.; Omachi, C.; Onofre, A.; Onyisi, P. U. E.; Oram, C. J.; Oreglia, M. J.; Oren, Y.; Orestano, D.; Orlov, I.; Oropeza Barrera, C.; Orr, R. S.; Ortega, E. O.; Osculati, B.; Ospanov, R.; Osuna, C.; Ottersbach, J. P.; Ould-Saada, F.; Ouraou, A.; Ouyang, Q.; Owen, M.; Owen, S.; Oyarzun, A.; Ozcan, V. E.; Ozone, K.; Ozturk, N.; Pacheco Pages, A.; Padilla Aranda, C.; Paganis, E.; Pahl, C.; Paige, F.; Pajchel, K.; Palestini, S.; Pallin, D.; Palma, A.; Palmer, J. D.; Pan, Y. B.; Panagiotopoulou, E.; Panes, B.; Panikashvili, N.; Panitkin, S.; Pantea, D.; Panuskova, M.; Paolone, V.; Papadopoulou, Th. D.; Park, S. J.; Park, W.; Parker, M. A.; Parker, S. I.; Parodi, F.; Parsons, J. A.; Parzefall, U.; Pasqualucci, E.; Passeri, A.; Pastore, F.; Pastore, Fr.; Pásztor, G.; Pataraia, S.; Pater, J. R.; Patricelli, S.; Patwa, A.; Pauly, T.; Peak, L. S.; Pecsy, M.; Pedraza Morales, M. I.; Peleganchuk, S. V.; Peng, H.; Penson, A.; Penwell, J.; Perantoni, M.; Perez, K.; Perez Codina, E.; Pérez García-Estañ, M. T.; Perez Reale, V.; Perini, L.; Pernegger, H.; Perrino, R.; Persembe, S.; Perus, P.; Peshekhonov, V. D.; Petersen, B. A.; Petersen, T. C.; Petit, E.; Petridou, C.; Petrolo, E.; Petrucci, F.; Petschull, D.; Petteni, M.; Pezoa, R.; Phan, A.; Phillips, A. W.; Piacquadio, G.; Piccinini, M.; Piegaia, R.; Pilcher, J. E.; Pilkington, A. D.; Pina, J.; Pinamonti, M.; Pinfold, J. L.; Pinto, B.; Pizio, C.; Placakyte, R.; Plamondon, M.; Pleier, M.-A.; Poblaguev, A.; Poddar, S.; Podlyski, F.; Poffenberger, P.; Poggioli, L.; Pohl, M.; Polci, F.; Polesello, G.; Policicchio, A.; Polini, A.; Poll, J.; Polychronakos, V.; Pomeroy, D.; Pommès, K.; Ponsot, P.; Pontecorvo, L.; Pope, B. G.; Popeneciu, G. A.; Popovic, D. S.; Poppleton, A.; Popule, J.; Portell Bueso, X.; Porter, R.; Pospelov, G. E.; Pospisil, S.; Potekhin, M.; Potrap, I. N.; Potter, C. J.; Potter, C. T.; Potter, K. P.; Poulard, G.; Poveda, J.; Prabhu, R.; Pralavorio, P.; Prasad, S.; Pravahan, R.; Pribyl, L.; Price, D.; Price, L. E.; Prichard, P. M.; Prieur, D.; Primavera, M.; Prokofiev, K.; Prokoshin, F.; Protopopescu, S.; Proudfoot, J.; Prudent, X.; Przysiezniak, H.; Psoroulas, S.; Ptacek, E.; Puigdengoles, C.; Purdham, J.; Purohit, M.; Puzo, P.; Pylypchenko, Y.; Qi, M.; Qian, J.; Qian, W.; Qin, Z.; Quadt, A.; Quarrie, D. R.; Quayle, W. B.; Quinonez, F.; Raas, M.; Radeka, V.; Radescu, V.; Radics, B.; Rador, T.; Ragusa, F.; Rahal, G.; Rahimi, A. M.; Rajagopalan, S.; Rammensee, M.; Rammes, M.; Rauscher, F.; Rauter, E.; Raymond, M.; Read, A. L.; Rebuzzi, D. M.; Redelbach, A.; Redlinger, G.; Reece, R.; Reeves, K.; Reinherz-Aronis, E.; Reinsch, A.; Reisinger, I.; Reljic, D.; Rembser, C.; Ren, Z. L.; Renkel, P.; Rescia, S.; Rescigno, M.; Resconi, S.; Resende, B.; Reznicek, P.; Rezvani, R.; Richards, A.; Richards, R. A.; Richter, R.; Richter-Was, E.; Ridel, M.; Rijpstra, M.; Rijssenbeek, M.; Rimoldi, A.; Rinaldi, L.; Rios, R. R.; Riu, I.; Rizatdinova, F.; Rizvi, E.; Roa Romero, D. A.; Robertson, S. H.; Robichaud-Veronneau, A.; Robinson, D.; Robinson, J. E. M.; Robinson, M.; Robson, A.; Rocha de Lima, J. G.; Roda, C.; Roda Dos Santos, D.; Rodriguez, D.; Rodriguez Garcia, Y.; Roe, S.; Røhne, O.; Rojo, V.; Rolli, S.; Romaniouk, A.; Romanov, V. M.; Romeo, G.; Romero Maltrana, D.; Roos, L.; Ros, E.; Rosati, S.; Rosenbaum, G. A.; Rosselet, L.; Rossetti, V.; Rossi, L. P.; Rotaru, M.; Rothberg, J.; Rousseau, D.; Royon, C. R.; Rozanov, A.; Rozen, Y.; Ruan, X.; Ruckert, B.; Ruckstuhl, N.; Rud, V. I.; Rudolph, G.; Rühr, F.; Ruggieri, F.; Ruiz-Martinez, A.; Rumyantsev, L.; Rurikova, Z.; Rusakovich, N. A.; Rutherfoord, J. P.; Ruwiedel, C.; Ruzicka, P.; Ryabov, Y. F.; Ryan, P.; Rybkin, G.; Rzaeva, S.; Saavedra, A. F.; Sadrozinski, H. F.-W.; Sadykov, R.; Sakamoto, H.; Salamanna, G.; Salamon, A.; Saleem, M. S.; Salihagic, D.; Salnikov, A.; Salt, J.; Salvachua Ferrando, B. M.; Salvatore, D.; Salvatore, F.; Salvucci, A.; Salzburger, A.; Sampsonidis, D.; Samset, B. H.; Sandaker, H.; Sander, H. G.; Sanders, M. P.; Sandhoff, M.; Sandhu, P.; Sandstroem, R.; Sandvoss, S.; Sankey, D. P. C.; Sanny, B.; Sansoni, A.; Santamarina Rios, C.; Santoni, C.; Santonico, R.; Saraiva, J. G.; Sarangi, T.; Sarkisyan-Grinbaum, E.; Sarri, F.; Sasaki, O.; Sasao, N.; Satsounkevitch, I.; Sauvage, G.; Savard, P.; Savine, A. Y.; Savinov, V.; Sawyer, L.; Saxon, D. H.; Says, L. P.; Sbarra, C.; Sbrizzi, A.; Scannicchio, D. A.; Schaarschmidt, J.; Schacht, P.; Schäfer, U.; Schaetzel, S.; Schaffer, A. C.; Schaile, D.; Schamberger, R. D.; Schamov, A. G.; Schegelsky, V. A.; Scheirich, D.; Schernau, M.; Scherzer, M. I.; Schiavi, C.; Schieck, J.; Schioppa, M.; Schlenker, S.; Schmidt, E.; Schmieden, K.; Schmitt, C.; Schmitz, M.; Schott, M.; Schouten, D.; Schovancova, J.; Schram, M.; Schreiner, A.; Schroeder, C.; Schroer, N.; Schroers, M.; Schultes, J.; Schultz-Coulon, H.-C.; Schumacher, J. W.; Schumacher, M.; Schumm, B. A.; Schune, Ph.; Schwanenberger, C.; Schwartzman, A.; Schwemling, Ph.; Schwienhorst, R.; Schwierz, R.; Schwindling, J.; Scott, W. G.; Searcy, J.; Sedykh, E.; Segura, E.; Seidel, S. C.; Seiden, A.; Seifert, F.; Seixas, J. M.; Sekhniaidze, G.; Seliverstov, D. M.; Sellden, B.; Semprini-Cesari, N.; Serfon, C.; Serin, L.; Seuster, R.; Severini, H.; Sevior, M. E.; Sfyrla, A.; Shabalina, E.; Shamim, M.; Shan, L. Y.; Shank, J. T.; Shao, Q. T.; Shapiro, M.; Shatalov, P. B.; Shaw, K.; Sherman, D.; Sherwood, P.; Shibata, A.; Shimojima, M.; Shin, T.; Shmeleva, A.; Shochet, M. J.; Shupe, M. A.; Sicho, P.; Sidoti, A.; Siegert, F.; Siegrist, J.; Sijacki, Dj.; Silbert, O.; Silva, J.; Silver, Y.; Silverstein, D.; Silverstein, S. B.; Simak, V.; Simic, Lj.; Simion, S.; Simmons, B.; Simonyan, M.; Sinervo, P.; Sinev, N. B.; Sipica, V.; Siragusa, G.; Sisakyan, A. N.; Sivoklokov, S. Yu.; Sjoelin, J.; Sjursen, T. B.; Skovpen, K.; Skubic, P.; Slater, M.; Slavicek, T.; Sliwa, K.; Sloper, J.; Sluka, T.; Smakhtin, V.; Smirnov, S. Yu.; Smirnov, Y.; Smirnova, L. N.; Smirnova, O.; Smith, B. C.; Smith, D.; Smith, K. M.; Smizanska, M.; Smolek, K.; Snesarev, A. A.; Snow, S. W.; Snow, J.; Snuverink, J.; Snyder, S.; Soares, M.; Sobie, R.; Sodomka, J.; Soffer, A.; Solans, C. A.; Solar, M.; Solc, J.; Solfaroli Camillocci, E.; Solodkov, A. A.; Solovyanov, O. V.; Soluk, R.; Sondericker, J.; Sopko, V.; Sopko, B.; Sosebee, M.; Soukharev, A.; Spagnolo, S.; Spanò, F.; Spencer, E.; Spighi, R.; Spigo, G.; Spila, F.; Spiwoks, R.; Spousta, M.; Spreitzer, T.; Spurlock, B.; Denis, R. D. St.; Stahl, T.; Stahlman, J.; Stamen, R.; Stancu, S. N.; Stanecka, E.; Stanek, R. W.; Stanescu, C.; Stapnes, S.; Starchenko, E. A.; Stark, J.; Staroba, P.; Starovoitov, P.; Stastny, J.; Stavina, P.; Stavropoulos, G.; Steele, G.; Steinbach, P.; Steinberg, P.; Stekl, I.; Stelzer, B.; Stelzer, H. J.; Stelzer-Chilton, O.; Stenzel, H.; Stevenson, K.; Stewart, G. A.; Stockton, M. C.; Stoerig, K.; Stoicea, G.; Stonjek, S.; Strachota, P.; Stradling, A. R.; Straessner, A.; Strandberg, J.; Strandberg, S.; Strandlie, A.; Strauss, M.; Strizenec, P.; Ströhmer, R.; Strom, D. M.; Stroynowski, R.; Strube, J.; Stugu, B.; Soh, D. A.; Su, D.; Sugaya, Y.; Sugimoto, T.; Suhr, C.; Suk, M.; Sulin, V. V.; Sultansoy, S.; Sumida, T.; Sun, X. H.; Sundermann, J. E.; Suruliz, K.; Sushkov, S.; Susinno, G.; Sutton, M. R.; Suzuki, T.; Suzuki, Y.; Sykora, I.; Sykora, T.; Szymocha, T.; Sánchez, J.; Ta, D.; Tackmann, K.; Taffard, A.; Tafirout, R.; Taga, A.; Takahashi, Y.; Takai, H.; Takashima, R.; Takeda, H.; Takeshita, T.; Talby, M.; Talyshev, A.; Tamsett, M. C.; Tanaka, J.; Tanaka, R.; Tanaka, S.; Tanaka, S.; Tapprogge, S.; Tardif, D.; Tarem, S.; Tarrade, F.; Tartarelli, G. F.; Tas, P.; Tasevsky, M.; Tassi, E.; Tatarkhanov, M.; Taylor, C.; Taylor, F. E.; Taylor, G. N.; Taylor, R. P.; Taylor, W.; Teixeira-Dias, P.; Ten Kate, H.; Teng, P. K.; Tennenbaum-Katan, Y. D.; Terada, S.; Terashi, K.; Terron, J.; Terwort, M.; Testa, M.; Teuscher, R. J.; Thioye, M.; Thoma, S.; Thomas, J. P.; Thompson, E. N.; Thompson, P. D.; Thompson, P. D.; Thompson, R. J.; Thompson, A. S.; Thomson, E.; Thun, R. P.; Tic, T.; Tikhomirov, V. O.; Tikhonov, Y. A.; Tipton, P.; Tique Aires Viegas, F. J.; Tisserant, S.; Toczek, B.; Todorov, T.; Todorova-Nova, S.; Toggerson, B.; Tojo, J.; Tokár, S.; Tokushuku, K.; Tollefson, K.; Tomasek, L.; Tomasek, M.; Tomoto, M.; Tompkins, L.; Toms, K.; Tonoyan, A.; Topfel, C.; Topilin, N. D.; Torrence, E.; Torró Pastor, E.; Toth, J.; Touchard, F.; Tovey, D. R.; Trefzger, T.; Tremblet, L.; Tricoli, A.; Trigger, I. M.; Trincaz-Duvoid, S.; Trinh, T. N.; Tripiana, M. F.; Triplett, N.; Trischuk, W.; Trivedi, A.; Trocmé, B.; Troncon, C.; Trzupek, A.; Tsarouchas, C.; Tseng, J. C.-L.; Tsiakiris, M.; Tsiareshka, P. V.; Tsionou, D.; Tsipolitis, G.; Tsiskaridze, V.; Tskhadadze, E. G.; Tsukerman, I. I.; Tsulaia, V.; Tsung, J.-W.; Tsuno, S.; Tsybychev, D.; Tuggle, J. M.; Turecek, D.; Turk Cakir, I.; Turlay, E.; Tuts, P. M.; Twomey, M. S.; Tylmad, M.; Tyndel, M.; Uchida, K.; Ueda, I.; Ugland, M.; Uhlenbrock, M.; Uhrmacher, M.; Ukegawa, F.; Unal, G.; Undrus, A.; Unel, G.; Unno, Y.; Urbaniec, D.; Urkovsky, E.; Urquijo, P.; Urrejola, P.; Usai, G.; Uslenghi, M.; Vacavant, L.; Vacek, V.; Vachon, B.; Vahsen, S.; Valente, P.; Valentinetti, S.; Valkar, S.; Valladolid Gallego, E.; Vallecorsa, S.; Valls Ferrer, J. A.; van Berg, R.; van der Graaf, H.; van der Kraaij, E.; van der Poel, E.; van der Ster, D.; van Eldik, N.; van Gemmeren, P.; van Kesteren, Z.; van Vulpen, I.; Vandelli, W.; Vaniachine, A.; Vankov, P.; Vannucci, F.; Vari, R.; Varnes, E. W.; Varouchas, D.; Vartapetian, A.; Varvell, K. E.; Vasilyeva, L.; Vassilakopoulos, V. I.; Vazeille, F.; Vellidis, C.; Veloso, F.; Veneziano, S.; Ventura, A.; Ventura, D.; Venturi, M.; Venturi, N.; Vercesi, V.; Verducci, M.; Verkerke, W.; Vermeulen, J. C.; Vetterli, M. C.; Vichou, I.; Vickey, T.; Viehhauser, G. H. A.; Villa, M.; Villani, E. G.; Villaplana Perez, M.; Vilucchi, E.; Vincter, M. G.; Vinek, E.; Vinogradov, V. B.; Viret, S.; Virzi, J.; Vitale, A.; Vitells, O.; Vivarelli, I.; Vives Vaque, F.; Vlachos, S.; Vlasak, M.; Vlasov, N.; Vogel, A.; Vokac, P.; Volpi, M.; von der Schmitt, H.; von Loeben, J.; von Radziewski, H.; von Toerne, E.; Vorobel, V.; Vorwerk, V.; Vos, M.; Voss, R.; Voss, T. T.; Vossebeld, J. H.; Vranjes, N.; Vranjes Milosavljevic, M.; Vrba, V.; Vreeswijk, M.; Vu Anh, T.; Vudragovic, D.; Vuillermet, R.; Vukotic, I.; Wagner, P.; Walbersloh, J.; Walder, J.; Walker, R.; Walkowiak, W.; Wall, R.; Wang, C.; Wang, H.; Wang, J.; Wang, S. M.; Warburton, A.; Ward, C. P.; Warsinsky, M.; Wastie, R.; Watkins, P. M.; Watson, A. T.; Watson, M. F.; Watts, G.; Watts, S.; Waugh, A. T.; Waugh, B. M.; Weber, M. D.; Weber, M.; Weber, M. S.; Weber, P.; Weidberg, A. R.; Weingarten, J.; Weiser, C.; Wellenstein, H.; Wells, P. S.; Wen, M.; Wenaus, T.; Wendler, S.; Wengler, T.; Wenig, S.; Wermes, N.; Werner, M.; Werner, P.; Werth, M.; Werthenbach, U.; Wessels, M.; Whalen, K.; White, A.; White, M. J.; White, S.; Whitehead, S. R.; Whiteson, D.; Whittington, D.; Wicek, F.; Wicke, D.; Wickens, F. J.; Wiedenmann, W.; Wielers, M.; Wienemann, P.; Wiglesworth, C.; Wiik, L. A. M.; Wildauer, A.; Wildt, M. A.; Wilkens, H. G.; Williams, E.; Williams, H. H.; Willocq, S.; Wilson, J. A.; Wilson, M. G.; Wilson, A.; Wingerter-Seez, I.; Winklmeier, F.; Wittgen, M.; Wolter, M. W.; Wolters, H.; Wosiek, B. K.; Wotschack, J.; Woudstra, M. J.; Wraight, K.; Wright, C.; Wright, D.; Wrona, B.; Wu, S. L.; Wu, X.; Wulf, E.; Wynne, B. M.; Xaplanteris, L.; Xella, S.; Xie, S.; Xu, D.; Xu, N.; Yamada, M.; Yamamoto, A.; Yamamoto, K.; Yamamoto, S.; Yamamura, T.; Yamaoka, J.; Yamazaki, T.; Yamazaki, Y.; Yan, Z.; Yang, H.; Yang, U. K.; Yang, Z.; Yao, W.-M.; Yao, Y.; Yasu, Y.; Ye, J.; Ye, S.; Yilmaz, M.; Yoosoofmiya, R.; Yorita, K.; Yoshida, R.; Young, C.; Youssef, S. P.; Yu, D.; Yu, J.; Yuan, L.; Yurkewicz, A.; Zaidan, R.; Zaitsev, A. M.; Zajacova, Z.; Zambrano, V.; Zanello, L.; Zaytsev, A.; Zeitnitz, C.; Zeller, M.; Zemla, A.; Zendler, C.; Zenin, O.; Zenis, T.; Zenonos, Z.; Zenz, S.; Zerwas, D.; Zevi Della Porta, G.; Zhan, Z.; Zhang, H.; Zhang, J.; Zhang, Q.; Zhang, X.; Zhao, L.; Zhao, T.; Zhao, Z.; Zhemchugov, A.; Zhong, J.; Zhou, B.; Zhou, N.; Zhou, Y.; Zhu, C. G.; Zhu, H.; Zhu, Y.; Zhuang, X.; Zhuravlov, V.; Zimmermann, R.; Zimmermann, S.; Zimmermann, S.; Ziolkowski, M.; Živković, L.; Zobernig, G.; Zoccoli, A.; Zur Nedden, M.; Zutshi, V.

    2010-12-01

    The simulation software for the ATLAS Experiment at the Large Hadron Collider is being used for large-scale production of events on the LHC Computing Grid. This simulation requires many components, from the generators that simulate particle collisions, through packages simulating the response of the various detectors and triggers. All of these components come together under the ATLAS simulation infrastructure. In this paper, that infrastructure is discussed, including that supporting the detector description, interfacing the event generation, and combining the GEANT4 simulation of the response of the individual detectors. Also described are the tools allowing the software validation, performance testing, and the validation of the simulated output against known physics processes.

  10. Preliminary Response of Soil Fauna to Simulated N Deposition in Three Typical Subtropical Forests

    Institute of Scientific and Technical Information of China (English)

    XU Guo-Liang; MO Jiang-Ming; ZHOU Guo-Yi; FU Sheng-Lei

    2006-01-01

    A field-scale experiment arranged in a complete randomized block design with three N addition treatments including a control (no addition of N), a low N (5 g m-2 year-1), and a medium N (10 g m-2 year-1) was performed in each of the three typical forests, a pine (Pinus massoniana Lamb.) forest (PF), a pine-broadleaf mixed forest (MF) and a mature monsoon evergreen broadleaf forest (MEBF), of the Dinghushan Biosphere Reserve in subtropical China to study the response of soil fauna community to additions of N. Higher NH4+ and NO3- concentrations and a lower soil pH occurred in the medium N treatment of MEBF, whereas the NO3- concentration was the lowest in PF after the additions of N. The response of the density, group abundance and diversity index of soil fauna to addition of N varied with the forest type,and all these variables decreased with increasing N under MEBF but the trend was opposite under PF. The N treatments had no significant effects on these variables under MF. Compared with the control plots, the medium N treatment had significant negative effect on soil fauna under MEBF. The group abundance of soil fauna increased significantly with additions of higher N rates under PF. These results suggested that the response of soil fauna to N deposition varied with the forest type and N deposition rate, and soil N status is one of the important factors affecting the response of soil fauna to N deposition.

  11. Preliminary Design, Simulation, and Test of the Electrical Power Subsystem of the TINYSCOPE Nanosatellite

    Science.gov (United States)

    2009-12-01

    With 18650 Cell................................................. 46 Figure 15. Depth-of-Discharge versus Cycle Life for NiCd & NH2 From [15...14.4 V, i.e., 3.6 x 4 = 14.4. Three of these strings provide 6.6 Ah of total capacity, i.e., 2.2 x 3 = 6.6. The cells conform to the standard 18650 ...on top, “flat pack” bottom right) along with a representative 18650 lithium ion cell from inside the case (bottom left). Figure 14. IBPS OEM

  12. Preliminary design features of the RASCAL - A NASA/Army rotorcraft in-flight simulator

    Science.gov (United States)

    Aiken, Edwin W.; Jacobsen, Robert A.; Eshow, Michelle M.; Hindson, William S.; Doane, Douglas H.

    1992-01-01

    Salient design features of a new NASA/Army research rotorcraft - the Rotorcraft Aircrew Systems Concepts Airborne Laboratory (RASCAL) - are described. Using a UH-60A Black Hawk helicopter as a baseline vehicle, the RASCAL will be a flying laboratory capable of supporting the research requirements of major NASA and Army guidance, control, and display research programs. The paper describes the research facility requirements of these programs together with other critical constraints on the design of the research system, including safety-of-flight. Research program schedules demand a phased development approach, wherein specific research capability milestones are met and flight research projects are flown throughout the complete development cycle of the RASCAL. This development approach is summarized, and selected features of the research system are described. The research system includes a full-authority, programmable, fault-tolerant/fail-safe, fly-by-wire flight control system and a real-time obstacle detection and avoidance system which will generate low-latitude guidance commands to the pilot on a wide field-of-view, color helmet-mounted display.

  13. Preliminary design features of the RASCAL: A NASA /Army rotorcraft in-flight simulator

    Science.gov (United States)

    Aiken, Edwin W.; Jacobsen, Robert A.; Eshow, Michelle M.; Hindson, William S.; Doane, Douglas H.

    1993-01-01

    Salient design features of a new NASA/Army research rotorcraft - the Rotorcraft-Aircrew Systems Concepts Airborne Laboratory (RASCAL) - are described. Using a UH-60A Black Hawk helicopter as a baseline vehicle, the RASCAL will be a flying laboratory capable of supporting the research requirements of major NASA and Army guidance, control, and display research programs. The paper describes the research facility requirements of these programs together with other critical constraints on the design of the research system, including safety-of-flight. Research program schedules demand a phased development approach, wherein specific research capability milestones are met and flight research projects are flown throughout the complete development cycle of the RASCAL. This development approach is summarized, and selected features of the research system are described. The research system includes a full-authority, programmable, fault-tolerant/fail-safe, fly-by-wire flight control system and a real-time obstacle detection and avoidance system which will generate low-altitude guidance commands to the pilot on a wide field-of-view, color helmet-mounted display.

  14. Crude Oil Sludge Degradation in Microcosmic Scale: Simple Simulation as Preliminary Study on Land Treatment Bioremediation.

    Directory of Open Access Journals (Sweden)

    Astri Nugroho

    2010-10-01

    Full Text Available A study in microcosmic condition has been carried out to evaluate the bacterial hydrocarbonoclastic capability in increasing the oil sludge degradation being mixed with NPK fertilizer as nitrogen resources. Aerobic test was carried out by putting erlenmeyers in a shaker incubator, 120 rpm shaking speed, at 50°C temperature. While 150 days in microcosmic one observation showed that the consortium has the potential to grow up to 50% (v/v sludge oil load. Maximum growth and  maximum growth rate of the consortium occurred in the III C treatment (by adding 50% (v/v sludge oil and by mixing nitrogen in the form of NPK fertilizer amounting 30% (w/v of added substrat. The observation showed that at the day 150, all the treatments were degradated above 64%. Highest degradation accured in the III A treatment followed by the III C treatment amounting 88.72% and 87.19% respectively. The gas chromatography analysis showed that at t15 and t30, hydrocarbon C8 and C9 turned up and then vanished after t30. Hydrocarbon do increased at t30 while the relative abundance of C11 up to C17 was decreasing gradually. The biggest decreasing of that was in C14, as 85.28% before and 43.11% after. At the end of the study 7 species of bacteria were identified, 5 of them are of Bacillus sp, which are aerobical

  15. Preliminary Study of Strong-Sludge Gas Retention and Release Mechanisms in Clay Simulants

    Energy Technology Data Exchange (ETDEWEB)

    Gauglitz, Phillip A.; Buchmiller, William C.; Probert, Samuel G.; Owen, Antionette T.

    2010-10-12

    The Hanford Site has 28 double-shell tanks (DSTs) and 149 single-shell tanks (SSTs) containing radioactive wastes that are complex mixes of radioactive and chemical products. The mission of the Department of Energy’s River Protection Project is to retrieve and treat the Hanford tank waste for disposal and close the tank farms. A key aspect of the mission is to retrieve and transfer waste from the SSTs, which are at greater risk for leaking, into DSTs for interim storage until the waste is transferred to and treated in the Waste Treatment and Immobilization Plant. There is, however, limited space in the existing DSTs to accept waste transfers from the SSTs, and approaches to overcoming the limited DST space will benefit the overall mission. The purpose of this study is to summarize and analyze the key previous experiment that forms the basis for the relaxed controls and to summarize initial progress and results on new experiments focused on understanding the conditions that result in low gas retention. The work is ongoing; this report provides a summary of the initial findings. The previous large-scale test used about 50 m3 of sediment, which would be unwieldy for doing multiple parametric experiments. Accordingly, experiments will begin with smaller-scale tests to determine whether the desired mechanisms can be studied without the difficulty of conducting very large experiments.

  16. High frame-rate blood vector velocity imaging using plane waves: simulations and preliminary experiments

    DEFF Research Database (Denmark)

    Udesen, J.; Gran, F.; Hansen, K.L.

    2008-01-01

    Conventional ultrasound methods for acquiring color images of blood velocity are limited by a relatively low frame-rate and are restricted to give velocity estimates along the ultrasound beam direction only. To circumvent these limitations, the method presented in this paper uses 3 techniques: 1...... carotid artery of a healthy male was scanned with a scan sequence that satisfies the limits set by the Food and Drug Administration. Vector velocity images were obtained with a frame-rate of 100 Hz where 40 speckle images are used for each vector velocity image. It was found that the blood flow...... approximately followed the vessel wall, and that maximum velocity was approximately 1 m/s, which is a normal value for a healthy person. To further evaluate the method, the test person was scanned with magnetic resonance (MR) angiography. The volume flow derived from the MR scanning was compared with that from...

  17. Fast Blood Vector Velocity Imaging: Simulations and Preliminary In Vivo Results

    DEFF Research Database (Denmark)

    Udesen, Jesper; Gran, Fredrik; Hansen, Kristoffer Lindskov

    2007-01-01

    for each pulse emission. 2) The transmitted pulse consists of a 13 bit Barker code which is transmitted simultaneously from each transducer element. 3) The 2-D vector velocity of the blood is found using 2-D speckle tracking between segments in consecutive speckle images. III Results: The method was tested...... rate can be significantly increased, and the full 2-D vector velocity of the blood can be estimated. II Method: The method presented in this paper uses three techniques: 1) The ultrasound is not focused during the transmit of the ultrasound signals, and a full speckle image of the blood can be acquired...

  18. Monte Carlo simulation applied in total reflection x-ray fluorescence: Preliminary results

    Energy Technology Data Exchange (ETDEWEB)

    Meira, Luiza L. C.; Inocente, Guilherme F.; Vieira, Leticia D.; Mesa, Joel [Departamento de Fisica e Biofisica - Instituto de Biociencias de Botucatu, Universidade Estadual Paulista Julio de Mesquita Filho (Brazil)

    2013-05-06

    The X-ray Fluorescence (XRF) analysis is a technique for the qualitative and quantitative determination of chemical constituents in a sample. This method is based on detection of the characteristic radiation intensities emitted by the elements of the sample, when properly excited. A variant of this technique is the Total Reflection X-ray Fluorescence (TXRF) that utilizes electromagnetic radiation as excitation source. In total reflection of X-ray, the angle of refraction of the incident beam tends to zero and the refracted beam is tangent to the sample support interface. Thus, there is a minimum angle of incidence at which no refracted beam exists and all incident radiation undergoes total reflection. In this study, we evaluated the influence of the energy variation of the beam of incident x-rays, using the MCNPX code (Monte Carlo NParticle) based on Monte Carlo method.

  19. Preliminary Results from Simulations of Temperature Fluctuations in Stirling Engine Regenerator Matrices

    DEFF Research Database (Denmark)

    Andersen, Stig Kildegård; Carlsen, Henrik; Thomsen, Per Grove

    2003-01-01

    The objective of this study has been to create a model for studying effects of temperature fluctuations in regenerator matrices on Stirling engine performance. A one-dimensional model with axial discretisation of engine components has been formulated using a fixed Eulerian grid. The model contains...... a system of ordinary differential equations (ODEs) describing the mass and energy balances for the working gas in all control volumes and energy balances for the matrix material in the control volumes of the regenerator. Interpolation methods with filtering properties are used for state variables...... that adjusts solutions so that they satisfy the necessary cyclic boundary conditions as well as integral conditions for cyclic heat transfer for walls in the engine and for the mean cycle pressure. It has been found that it is possible to accurately solve the stiff ODE system that describes the coupled...

  20. Battalion Evaluation of the Combat Vehicle Command and Control System in Distributed Interactive Simulation. Preliminary Findings

    Science.gov (United States)

    1993-07-30

    Atwood , MG (Ret.) Charles Heiden, Mr. Owen Pitney, and Mr. Ryszard Lozicki. Mr. Jeffrey Schmidt and Ms. Margaret Shay provided invaluable assistance in...years has produced data of substantial operational significance (Leibrecht et al., 1992; Du Bois & Smith, 1991; Atwood , Quinkert, Campbell, Lameier...the CVCC training package ( Atwood et al., 1991), to conduct detailed task analyses (Morey, Wigginton & O’Brien, 1992), to prototype training methods

  1. Using computational simulation to aid in the prediction of socket fit: a preliminary study.

    Science.gov (United States)

    Lee, Winson C C; Zhang, Ming

    2007-10-01

    This study illustrates the use of computational analysis to predict prosthetic socket fit. A simple indentation test is performed by applying force to the residual limb of a trans-tibial amputee through an indenter until the subject perceives the onset of pain. Computational finite element (FE) analysis is then applied to evaluate the magnitude of pressure underlying the indenter that initiates pain (pain threshold pressure), and the pressure at the prosthetic socket-residual limb interface. The assessment of socket fit is examined by studying whether or not the socket-limb interface pressure exceeds the pain threshold pressure of the limb. Based on the computer-aided assessment, a new prosthetic socket is then fabricated and fitted to the amputee subject. Successful socket fit is achieved at the end of this process. The approach of using computational analysis to aid in assessing socket fit allows a more efficient evaluation and re-design of the socket even before the actual fabrication and fitting of the prosthetic socket. However, more thorough investigations are required before this approach can be widely used. A subsequent part of this paper discusses the limitations and suggests future research directions in this area.

  2. Preliminary application of virtual simulation and reposition template for zygomatico-orbitomaxillary complex fracture.

    Science.gov (United States)

    Li, Peng; Tang, Wei; Li, Jia; Tian, Dong W

    2012-09-01

    This report introduced and evaluated our computer-assisted surgical method in the treatment of complex maxillofacial fractures. One patient with zygomatico-orbitomaxillary complex fracture underwent computed tomography to obtain DICOM data. Three-dimensional reconstruction and virtual surgical planning were carried out in the software MIMICS 10.01. Three reposition templates and 1 skull model were manufactured in our three-dimensional rapid prototyping machine. Reconstruction surgery was carried out according to the preoperative planning and with the guide of reposition templates. At 3-month follow-up, the treatment outcome was consistent with preoperative planning exactly, and the patient expressed high satisfaction with the surgery. Combination of reposition templates and rapid prototyping method demonstrated great practical value in complex maxillofacial fracture surgery.

  3. In-tank fluid sloshing effects during earthquakes: A preliminary computational simulation

    Energy Technology Data Exchange (ETDEWEB)

    Park, J.E.; Rezvani, M.A.

    1995-04-01

    Hundreds of underground radioactive waste storage tanks are located at Department of Energy (DOE) sites. At present, no technique for evaluating the pressure loads due to the impact of earthquake generated waves on the side walls and dome of the tanks is known if the wave breaks back on itself. This paper presents the results of two-dimensional Computational Fluid Dynamics (CFD) calculations of the motion of waves in a generic rectangular tank as the result of accelerations recorded during an earthquake. The advantages and limitations of this technique and methods for avoiding the limitations will be discussed.

  4. Simulation of biomass-steam gasification in fluidized bed reactors: Model setup, comparisons and preliminary predictions.

    Science.gov (United States)

    Yan, Linbo; Lim, C Jim; Yue, Guangxi; He, Boshu; Grace, John R

    2016-12-01

    A user-defined solver integrating the solid-gas surface reactions and the multi-phase particle-in-cell (MP-PIC) approach is built based on the OpenFOAM software. The solver is tested against experiments. Then, biomass-steam gasification in a dual fluidized bed (DFB) gasifier is preliminarily predicted. It is found that the predictions agree well with the experimental results. The bed material circulation loop in the DFB can form automatically and the bed height is about 1m. The voidage gradually increases along the height of the bed zone in the bubbling fluidized bed (BFB) of the DFB. The U-bend and cyclone can separate the syngas in the BFB and the flue gas in the circulating fluidized bed. The concentration of the gasification products is relatively higher in the conical transition section, and the dry and nitrogen-free syngas at the BFB outlet is predicted to be composed of 55% H2, 20% CO, 20% CO2 and 5% CH4.

  5. Preliminary site description: Groundwater flow simulations. Simpevarp area (version 1.1) modelled with CONNECTFLOW

    Energy Technology Data Exchange (ETDEWEB)

    Hartley, Lee; Worth, David [Serco Assurance Ltd, Risley (United Kingdom); Gylling, Bjoern; Marsic, Niko [Kemakta Konsult AB, Stockholm (Sweden); Holmen, Johan [Golder Associates, Stockholm (Sweden)

    2004-08-01

    The main objective of this study is to assess the role of known and unknown hydrogeological conditions for the present-day distribution of saline groundwater at the Simpevarp and Laxemar sites. An improved understanding of the paleo-hydrogeology is necessary in order to gain credibility for the Site Descriptive Model in general and the Site Hydrogeological Description in particular. This is to serve as a basis for describing the present hydrogeological conditions as well as predictions of future hydrogeological conditions. This objective implies a testing of: geometrical alternatives in the structural geology and bedrock fracturing, variants in the initial and boundary conditions, and parameter uncertainties (i.e. uncertainties in the hydraulic property assignment). This testing is necessary in order to evaluate the impact on the groundwater flow field of the specified components and to promote proposals of further investigations of the hydrogeological conditions at the site. The general methodology for modelling transient salt transport and groundwater flow using CONNECTFLOW that was developed for Forsmark has been applied successfully also for Simpevarp. Because of time constraints only a key set of variants were performed that focussed on the influences of DFN model parameters, the kinematic porosity, and the initial condition. Salinity data in deep boreholes available at the time of the project was too limited to allow a good calibration exercise. However, the model predictions are compared with the available data from KLX01 and KLX02 below. Once more salinity data is available it may be possible to draw more definite conclusions based on the differences between variants. At the moment though the differences should just be used understand the sensitivity of the models to various input parameters.

  6. A mechanical experimental setup to simulate vocal folds vibrations. Preliminary results

    CERN Document Server

    Ruty, Nicolas; Pelorson, Xavier; Lopez-Arteaga, Ines; Hirschberg, Avraham

    2005-01-01

    This paper contributes to the understanding of vocal folds oscillation during phonation. In order to test theoretical models of phonation, a new experimental set-up using a deformable vocal folds replica is presented. The replica is shown to be able to produce self sustained oscillations under controlled experimental conditions. Therefore different parameters, such as those related to elasticity, to acoustical coupling or to the subglottal pressure can be quantitatively studied. In this work we focused on the oscillation fundamental frequency and the upstream pressure in order to start (on-set threshold) either end (off-set threshold) oscillations in presence of a downstream acoustical resonator. As an example, it is shown how this data can be used in order to test the theoretical predictions of a simple one-mass model.

  7. Design, Simulation, and Preliminary Testing of a 20 Ampere Energy Management System

    Science.gov (United States)

    2015-06-01

    Vre f 0.5 V 0.58 V Vil 0.8 V 1.1 V Vih 1.9 V 2.25 V An important feature of this power module is the smart shutdown feature [15]. A simpli- fied...protection is removed when the pin voltage reaches the high-logic level Vih [15]. Values for Rshunt , RSD, and CSD had to be selected to implement this over...0.58 V Vil 0.8 V Vih 2.25 V Table 3.3. Truth table for H-bridge IGBTs, from [16]. Logic Input Output Shutdown Pin Lower IGBT Upper IGBT Lower IGBT

  8. How does floodplain width affect floodplain river ecology? A preliminary exploration using simulations

    Science.gov (United States)

    Power, Mary E.; Parker, Gary; Dietrich, William E.; Sun, Adrian

    1995-09-01

    Hydraulic food chain models allow us to explore the linkages of river discharge regimes and river-floodplain morphology to the structure and dynamics of modeled food webs. Physical conditions (e.g. depth, width, velocity) that vary with river discharge affect the performance (birth, growth, feeding, movement, or death rates) of organisms or trophic groups. Their performances in turn affect their impacts on food webs and ecosystems in channel and floodplain habitats. Here we explore the impact of floodplain width (modeled as 1 ×, 10× and 40× the channel width) on a food web with two energy sources (detritus and vegetation), invertebrates that consume these, a size structured fish population which consumes invertebrates and in which larger fish cannibalize small fish, and birds which feed on large fish. Hydraulic linkages to trophic dynamics are assumed to be mediated in three ways: birds feed efficiently only in shallow water; plant carrying capacity varies non-linearly with water velocity, and mobile and drifting organisms are diluted and concentrated with spillover of river discharge to the floodplain, and its reconfinement to the channel. Aspects of this model are based on field observations of Junk and Bailey from the Amazon, of Sparks from the Mississippi, and on our observations of the Fly River in Papua New Guinea. The model produced several counter-intuitive results. Biomass of invertebrates and fish increased with floodplain width, but much more rapidly from 1 × to 10 × floodplains than from 10 × to 40 × floodplains. For birds, maximum biomass occurred on the 10× floodplain. Initially high bird biomass on the 40 × floodplain declined to extinction over time, because although favorable fishing conditions (shallow water) were most prolonged on the widest floodplain, this advantage was more than offset by the greater dilution of prey after spillover. Bird predation on large fish sometimes increased their biomass, by reducing cannibalism and thereby increasing the abundance of small fish available to grow into the larger size class. Sensitivity analyses indicated that model results were relatively robust to variation in parameter values that we chose, but much more exploration and calibration with field data are needed before we know how specific our results are to the structure and other assumptions of this model. We share with others the opinion that progress towards understanding complex dynamic systems like floodplain river ecosystems requires frequent feedback between modeling and field observations and experimentation. This understanding is crucial for river management and restoration. Organisms in real rivers have adapted to track and quickly exploit favorable conditions, and to avoid or endure adverse conditions. It is when we engineer away this environmental variability that we threaten the long term persistence of river-adapted biota.

  9. Exploring Arsenic danger awareness in the Polish Copper Basin via network simulation - preliminary results

    CERN Document Server

    Buda, Andrzej

    2016-01-01

    Information spread plays crucial role in risk management in case of environmental danger. The structure of local society may be well described by social network analysis. We have investigated the role of hubs within that concept. In case of danger, there are two different strategies of information management: 1) information spread that leads to awareness of the whole society 2) keeping the whole information in secret under control that leads to a partial social awareness, available to a small number of people only. In our model, the probability of information spread between two nodes is inverse proportional to connectivity of the next node because people who have a lot of connections are more immune. We have applied agent-based modelling on Barabasi Albert networks to explore various scenarios of information spread. We have considered recent arsenic environmental danger in G{\\l}og\\'ow and Legnica (Copper Basin) according to the official available data (2015 - 2016) from social network analysis point of view. ...

  10. 33 CFR 1.07-25 - Preliminary matters.

    Science.gov (United States)

    2010-07-01

    ... GENERAL PROVISIONS Enforcement; Civil and Criminal Penalty Proceedings § 1.07-25 Preliminary matters. (a... issue will preclude its consideration. (b) The right to a hearing is waived if the party does not...

  11. Preliminary report on Lake Bowdoin near Malta, Montana

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This preliminary report covers the physical features, land ownership, and water resources of the Lake Bowdoin area as part of a habitat improvement project.

  12. Wrinkle Ridges in Aeolis Dorsa, Mars: Preliminary Mapping

    Science.gov (United States)

    Borden, R. M.; Burr, D. M.

    2016-06-01

    Previous work has interpreted wrinkle ridges as compressional landforms caused by movement along blind thrust faults. Our preliminary mapping in the Aeolis Dorsa, Mars has identified widely distributed wrinkle ridges, suggesting episodic contraction.

  13. Preliminary Report on Seaside Sparrow Population Genetics Project

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This is a preliminary report on a genetic variation study that was conducted at St. Vincent National Wildlife Refuge. Blood samples were taken from 57 Seaside...

  14. Preliminary survey of biodiversity in New Chicago Marsh

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — During the late winter and early springs 1995, we conducted a preliminary survey of biodiversity in New Chicago Marsh (NCM), at the south end of San Francisco Bay,...

  15. Dual-fuel, dual-throat engine preliminary analysis

    Science.gov (United States)

    Obrien, C. J.

    1979-01-01

    A propulsion system analysis of the dual fuel, dual throat engine for launch vehicle applications was conducted. Basic dual throat engine characterization data were obtained to allow vehicle optimization studies to be conducted. A preliminary baseline engine system was defined.

  16. NOS CO-OPS Water Level Data, Preliminary, 1-Minute

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has recent, preliminary (not quality-controlled), 1-minute, water level (tide) data from NOAA NOS Center for Operational Oceanographic Products and...

  17. NOS CO-OPS Water Level Data, Preliminary, 6-Minute

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has recent, preliminary (not quality-controlled), 6-minute, water level (tide) data from NOAA NOS Center for Operational Oceanographic Products and...

  18. Preliminary fishery management report : Des Lacs National Wildlife Refuge

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — A study of fishery management at Des Lacs National Wildlife Refuge was conducted from June 18 to 20, 1952. This brief preliminary report will serve to highlight the...

  19. A preliminary survey of the genus Buchwaldoboletus (Boletales: Boletaceae)

    Science.gov (United States)

    Beatriz Ortiz-Santana; Ernst E. Both

    2011-01-01

    Buchwaldoboletus is a small genus of about a dozen species with a world-wide distribution. The boletes of this genus are non-mycorrhizal, saprophytic and lignicolous. A preliminary survey is provided and seven new combinations are proposed.

  20. Preliminary documentation and assessment of fish diversity in sub ...

    African Journals Online (AJOL)

    Preliminary documentation and assessment of fish diversity in sub-Saharan ... upon their life histories and degree of association with estuarine environments. ... Estuarine fish communities in Africa are strongly influenced by the prevailing ...

  1. Preliminary report on hepatic and cardiovascular risk assessment of ...

    African Journals Online (AJOL)

    Preliminary report on hepatic and cardiovascular risk assessment of ... The triglyceride level, artherogenic and coronary risk index of the mechanics was higher ... risk, mechanics, lipid profile, cardiovascular disease, liver dysfunction, benzene.

  2. FY2012 Office of Child Support Preliminary Report

    Data.gov (United States)

    U.S. Department of Health & Human Services — The Office of Child Support Preliminary Report highlights financial and statistical program achievements based on quarterly and annual data. In fiscal year (FY)...

  3. A biogeographic study of intermountain leeches : Preliminary report

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Preliminary report for a five year study on leeches in the intermountain west. This work began out of curiosity to determine what, besides fishes, occurred in the...

  4. An Algorithm for the Simulations of the Magnetized Neutron Star Cooling

    CERN Document Server

    Grigorian, H; Chubarian, E; Piloyan, A; Rafayelyan, M

    2015-01-01

    The model and algorithm for the cooling of the magnetized neutron stars are presented. The cooling evolution described by system of parabolic partial differential equations with non-linear coefficients is solved using Alternating Direction Implicit method. The difference scheme and the preliminary results of simulations are presented.

  5. Numerical simulations of dynamical gluinos in SU(3) Yang-Mills theory: first results

    Energy Technology Data Exchange (ETDEWEB)

    Feo, Alessandra; Kirchner, Robert; Luckmann, Silke; Montvay, Istvan; Muenster, Gernot

    2000-03-01

    In a numerical Monte Carlo simulation of SU(3) Yang-Mills theory with dynamical gluinos we have investigated the behaviour of the expectation value of the scalar and pseudoscalar gluino condensates in order to determine the phase structure. Preliminary results are presented as a function of the hopping parameter.

  6. Numerical simulations of dynamical gluinos in SU(3) Yang-Mills theory first results

    CERN Document Server

    Feo, A; Luckmann, S; Montvay, István; Münster, G; Feo, Alessandra; Kirchner, Robert; Luckmann, Silke; Montvay, Istvan; Münster, Gernot

    2000-01-01

    In a numerical Monte Carlo simulation of SU(3) Yang-Mills theory with dynamical gluinos we have investigated the behaviour of the expectation value of the scalar and pseudoscalar gluino condensates in order to determine the phase structure. Preliminary results are presented as a function of the hopping parameter.

  7. Numerical simulations of dynamical gluinos in SU (3) Yang-Mills theory: first results

    Science.gov (United States)

    Feo, Alessandra; Kirchner, Robert; Luckmann, Silke; Montvay, István; Münster, Gernot; DESY-Münster Collaboration

    In a numerical Monte Carlo simulation of SU(3) Yang-Mills theory with dynamical gluinos we have investigated the behaviour of the expectation value of the scalar and pseudoscalar gluino condensates in order to determine the phase structure. Preliminary results are presented as a function of the hopping parameter.

  8. Simulation-Based Business Case for PSS: A System Dynamics Framework

    DEFF Research Database (Denmark)

    Rodrigues, Vinicius Picanco; Pigosso, Daniela Cristina Antelmi; McAloone, Tim C.

    2017-01-01

    of a business case for PSS implementation and management, based on a System Dynamics simulation framework. With amaturity-oriented theoretical perspective and the associated capability concepts, the study provides insights into how the development of PSScapabilities can potentially affect corporate performance...... over time. The paper’s preliminary results identify the potential for managers andother decision-makers to use the business case simulator to assessing PSS-related business benefits and responding to multiple implementationscenarios and strategies....

  9. Simulated Dynamics of Underpotential Deposition of Cu with Sulfate on Au(111)

    OpenAIRE

    Brown, Gregory; Rikvold, Per Arne; Novotny, M. A.; Wieckowski, Andrzej

    1997-01-01

    Numerical studies of lattice-gas models are well suited to describe multi-adsorbate systems. One example is the underpotential deposition of Cu on Au(111) in the presence of sulfuric acid. Preliminary results from dynamic Monte Carlo simulations of the evolution of the adsorbed layer during potential-step experiments across phase transitions are presented for this particular system. The simulated current profiles reproduce a strong asymmetry seen in recent experiments. Examination of the micr...

  10. Validation of simulation strategies for the flow in a model propeller turbine during a runaway event

    Science.gov (United States)

    Fortin, M.; Houde, S.; Deschênes, C.

    2014-03-01

    Recent researches indicate that the useful life of a turbine can be affected by transient events. This study aims to define and validate strategies for the simulation of the flow within a propeller turbine model in runaway condition. Using unsteady pressure measurements on two runner blades for validation, different strategies are compared and their results analysed in order to quantify their precision. This paper will focus on justifying the choice of the simulations strategies and on the analysis of preliminary results.

  11. Preliminary design package for prototype solar heating system

    Science.gov (United States)

    1978-01-01

    A summary is given of the preliminary analysis and design activity on solar heating systems. The analysis was made without site specific data other than weather; therefore, the results indicate performance expected under these special conditions. Major items include system candidates, design approaches, trade studies and other special data required to evaluate the preliminary analysis and design. The program calls for the development and delivery of eight prototype solar heating and cooling systems for installation and operational test.

  12. PRELIMINARY PHYTOCHEMICAL AND HISTOCHEMICAL INVESTIGATION ON KIGELIA PINNATA DC.,

    OpenAIRE

    Dhanasekaran, M.; ABRAHAM.G.C; Mohan, S.

    2014-01-01

    Kigelia pinnata D.C. the mid sized ornamental tree of the Bignoniaceae has been studied by preliminary phytochemical and histochemical analysis. Several local names are availability to this plants based on their country. They are called worsboom in Africa and sauage tree in America. The tree is 25 meters in hight with a dense rounded crown bark grey. Data gathered on solvent extraction and preliminary phytochemical method suggested that the presence of glycosides, flavonoides, tannin and alka...

  13. Preliminary Study of Realistic Blast Impact on Cultured Brain Slices

    Science.gov (United States)

    2015-04-01

    hippocampal slice samples to better understand blast-induced brain damage. 15. SUBJECT TERMS RDX spheres , organotypic cultures of hippocampus, small...Preliminary Study of Realistic Blast Impact on Cultured Brain Slices by Thuvan Piehler, Rohan Banton, Lars Piehler, Richard Benjamin, Ray...Aberdeen Proving Ground, MD 21005-5066 ARL-TR-7197 April 2015 Preliminary Study of Realistic Blast Impact on Cultured Brain Slices Thuvan

  14. Preliminary investigation on monitoring transportation effects by full field methods: a digital holographic speckle pattern interferometry study on canvas paintings

    Science.gov (United States)

    Tsiranidou, Elsa; Bernikola, Eirini; Tornari, Vivi; Fankhauser, Thomas; Läuchli, Matthias; Palmbach, Cornelius; Bäschlin, Nathalie

    2011-06-01

    A preliminary investigation has taken place employing Digital Holographic Speckle Pattern Interferometry (DHSPI) in order to assess the effect of handling and transportation on canvas paintings. Canvas dummies were used on a series of measurements on a transport simulator which allows reproducible simulation of any transport logs in the laboratory. A number of cycles of controlled vibrations were applied on the samples and after each cycle a measurement with DHSPI was taken to monitor the behavior of the samples while increasing the vibration loading and also to record the conditions under which the first crack appears. The transport simulations in combination with DHSPI monitoring revealed the amplitude of oscillation where the first cracks appear on new canvas paintings and also the way these cracks grow. During the tests it was also feasible to locate areas at risk of future deterioration.

  15. Tidal Response of Preliminary Jupiter Model

    OpenAIRE

    Wahl, Sean M; Hubbard, Willam B.; Militzer, Burkhard

    2016-01-01

    In anticipation of improved observational data for Jupiter's gravitational field from the Juno spacecraft, we predict the static tidal response for a variety of Jupiter interior models based on ab initio computer simulations of hydrogen-helium mixtures. We calculate hydrostatic-equilibrium gravity terms using the non-perturbative concentric Maclaurin Spheroid (CMS) method that eliminates lengthy expansions used in the theory of figures. Our method captures terms arising from the coupled tidal...

  16. Preliminary assessment of night vision goggles in airborne forest fire suppression

    Science.gov (United States)

    Jennings, Sion; Craig, Greg; Erdos, Rob; Filiter, Don; Crowell, Bob; Macuda, Todd

    2007-04-01

    Helicopters are widely used in daytime forest fire suppression, conducting diverse tasks such as spotting, re-supply, medical evacuation and airborne delivery. However, they are not used at night for forest fire suppression operations. There would be many challenges when operating in the vicinity of forest fires at night, including scene obscuration from smoke and dynamic changes in lighting conditions. There is little data on the use of Night Vision Goggles (NVGs) for airborne forest fire suppression. The National Research Council of Canada (NRC), in collaboration with the Ontario Ministry of Natural Resources (OMNR), performed a preliminary flight test to examine the use of NVGs while operating near forest fires. The study also simulated limited aspects of night time water bucketing. The preliminary observations from this study suggest that NVGs have potential to improve the safety and efficiency of airborne forest fire suppression, including forest fire perimeter mapping and take-off and landing in the vicinity of open fires. NVG operations at some distance from the fire pose minimal risk to flight, and provide an enhanced capability to identify areas of combustion at greater distances and accuracy. Closer to the fire, NVG flight becomes more risk intensive as a consequence of a reduction in visibility attributable to the adverse effects on NVG performance of the excess radiation and smoke emitted by the fire. The preliminary results of this study suggest that water bucketing at night is a difficult operation with elevated risk. Further research is necessary to clarify the operational limitations and implementation of these devices in forest fire suppression.

  17. Large-scale nanocomposites simulations using hybrid particle/SCFT simulations

    Science.gov (United States)

    Sides, Scott

    2009-03-01

    Preliminary results from 2D simulations of block copolymer nanocomposites (Phys. Rev. Lett. Vol 96, 250601 (2006) have been performed using a hybrid self-consistent field theory (SCFT) algorithm. While these simulation results showed that the presence of nanoparticles could induce changes in block copolymer morphologies, quantitative agreement with experiments for the particle densities at this transition are not yet possible. A feature missing in the 2D hybrid simulations is the packing behavior of real, three-dimensional spherical particles embedded in lamellar layers or hexagonally packed cylinders formed by linear diblock chains. In order to carry out these hybrid particle/SCFT 3D simulations a new object-oriented SCFT framework has been developed. The object-oriented design enables the hybrid/SCFT simulations to be performed in a framework that is both numerically efficient and sufficiently flexible to incorporate new SCFT models easily, In particular, this new framework will be used to investigate the distribution of particle positions in diblock lamellar layers as function of nanoparticle density to study the interplay of patterning due to diblock domain structure and the chain depletion interaction between spherical particles.

  18. Archaeogeophysical investigations in Tiwanaku: preliminary results

    Science.gov (United States)

    Masini, Nicola; Sileo, Maria; Lasaponara, Rosa; Leucci, Giovanni; Orefici, Giuseppe; Rizzo, Enzo

    2017-04-01

    -1450) Tiwanaku was characterized by the resurgence of regional identities and polities In spite of the rich archaeological record numerous issues, related to the function and the extension of Tiwanaku, need to be investigated especially in the monumental core which includes the pyramid of Akapana, and other ceremonial places such Kalasasaya, Putuni and Kantatallita. To this aims some geophysical investigations were performed in 2009 and 2014 in the context of multidisciplinary research including the use of satellite remote sensing [8]. This paper deals with the discussion of preliminary results of geomagnetic and GPR investigations, some of which have been verified by trial archaeological excavations which have unearthed some buried structures, improving the knowledge of the ceremonial areas of Tiwanaku. References [1] Lasaponara R., Leucci G., Masini N., Persico R., Scardozzi G., Towards an operative use of remote sensing for exploring the past using satellite data: The case study of Hierapolis (Turkey), Remote sensing of Environment, 174 (2016) : 148-164, doi:10.1016/j.rse.2015.12.016 [2] Masini N., Lasaponara R., Rizzo E., Orefici G. 2012. Integrated Remote Sensing Approach in Cahuachi (Peru): Studies and Results of the ITACA Mission (2007-2010), In: Lasaponara R., Masini N. (Eds) 2012, Satellite Remote Sensing: a new tool for Archaeology, Springer, Verlag Berlin Heidelberg, ISBN 978-90-481-8800-0, doi: 10.1007/978-90-481-8801-7_14; pp. 307-344 [3] Rizzo E., Masini N., Lasaponara R., Orefici G. 2010, ArchaeoGeophysical methods in the Templo del Escalonado (Cahuachi, Nasca, Perù), Near Surface Geophysics 8 (5), 433-439, doi:10.3997/1873-0604.2010030 [4] Masini N., Rizzo E., Lasaponara R., and Orefici G. 2008, Integrated remote sensing techniques for the detection of buried archaeological adobe structures: preliminary results in Cahuachi (Peru), Advances in Geosciences, 19, 75-82 [5] Lasaponara R., Leucci G., Masini N., Persico R. 2014. Investigating archaeological looting

  19. Zika Virus Disease in Colombia - Preliminary Report.

    Science.gov (United States)

    Pacheco, Oscar; Beltrán, Mauricio; Nelson, Christina A; Valencia, Diana; Tolosa, Natalia; Farr, Sherry L; Padilla, Ana V; Tong, Van T; Cuevas, Esther L; Espinosa-Bode, Andrés; Pardo, Lissethe; Rico, Angélica; Reefhuis, Jennita; González, Maritza; Mercado, Marcela; Chaparro, Pablo; Martínez Duran, Mancel; Rao, Carol Y; Muñoz, María M; Powers, Ann M; Cuéllar, Claudia; Helfand, Rita; Huguett, Claudia; Jamieson, Denise J; Honein, Margaret A; Ospina Martínez, Martha L

    2016-06-15

    Background Colombia began official surveillance for Zika virus disease (ZVD) in August 2015. In October 2015, an outbreak of ZVD was declared after laboratory-confirmed disease was identified in nine patients. Methods Using the national population-based surveillance system, we assessed patients with clinical symptoms of ZVD from August 9, 2015, to April 2, 2016. Laboratory test results and pregnancy outcomes were evaluated for a subgroup of pregnant women. Concurrently, we investigated reports of microcephaly for evidence of congenital ZVD. Results By April 2, 2016, there were 65,726 cases of ZVD reported in Colombia, of which 2485 (4%) were confirmed by means of reverse-transcriptase-polymerase-chain-reaction (RT-PCR) assay. The overall reported incidence of ZVD among female patients was twice that in male patients. A total of 11,944 pregnant women with ZVD were reported in Colombia, with 1484 (12%) of these cases confirmed on RT-PCR assay. In a subgroup of 1850 pregnant women, more than 90% of women who were reportedly infected during the third trimester had given birth, and no infants with apparent abnormalities, including microcephaly, have been identified. A majority of the women who contracted ZVD in the first or second trimester were still pregnant at the time of this report. Among the cases of microcephaly investigated from January 2016 through April 2016, four patients had laboratory evidence of congenital ZVD; all were born to asymptomatic mothers who were not included in the ZVD surveillance system. Conclusions Preliminary surveillance data in Colombia suggest that maternal infection with the Zika virus during the third trimester of pregnancy is not linked to structural abnormalities in the fetus. However, the monitoring of the effect of ZVD on pregnant women in Colombia is ongoing. (Funded by Colombian Instituto Nacional de Salud and the Centers for Disease Control and Prevention.).

  20. Preliminary status of the CALET observations

    Science.gov (United States)

    Torii, Shoji

    2016-07-01

    The CALorimetric Electron Telescope (CALET) space experiment, which has been developed by Japan in collaboration with Italy and the United States, is a high-energy astroparticle physics mission to be installed on the International Space Station (ISS). The primary goals of the CALET mission include investigating possible nearby sources of high energy electrons, studying the details of galactic particle propagation and searching for dark matter signatures. During a two- year mission, extendable to five years, the CALET experiment will measure the flux of cosmic-ray electrons (including positrons) to 20 TeV, gamma-rays to 10 TeV and nuclei with Z=1 to 40 up to several 100 TeV. The instrument consists of two layers of segmented plastic scintillators for the cosmic-ray charge identification (CHD), a 3 radiation length thick tungsten-scintillating fiber imaging calorimeter (IMC) and a 27 radiation length thick lead-tungstate calorimeter (TASC). CALET has sufficient depth, imaging capabilities and excellent energy resolution to allow for a clear separation between hadrons and electrons and between charged particles and gamma rays. The instrument was launched on Aug. 19, 2015 to the ISS with HTV-5 (H-II Transfer Vehicle 5) and was successfully berthed to the Japanese Experiment Module- Exposure Facility (JEM-EF) . After a functional check-out phase until the beginning of October, it started an initial operation phase which was completed on Nov. 17, whence it began its standard operation phase. This paper will review the preliminary status of the CALET.

  1. Methodology for Preliminary Design of Electrical Microgrids

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, Richard P. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Stamp, Jason E. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Eddy, John P. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Henry, Jordan M [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Munoz-Ramos, Karina [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Abdallah, Tarek [U.S. Army Corps of Engineers, Washington, DC (United States)

    2015-09-30

    Many critical loads rely on simple backup generation to provide electricity in the event of a power outage. An Energy Surety Microgrid TM can protect against outages caused by single generator failures to improve reliability. An ESM will also provide a host of other benefits, including integration of renewable energy, fuel optimization, and maximizing the value of energy storage. The ESM concept includes a categorization for microgrid value proposi- tions, and quantifies how the investment can be justified during either grid-connected or utility outage conditions. In contrast with many approaches, the ESM approach explic- itly sets requirements based on unlikely extreme conditions, including the need to protect against determined cyber adversaries. During the United States (US) Department of Defense (DOD)/Department of Energy (DOE) Smart Power Infrastructure Demonstration for Energy Reliability and Security (SPIDERS) effort, the ESM methodology was successfully used to develop the preliminary designs, which direct supported the contracting, construction, and testing for three military bases. Acknowledgements Sandia National Laboratories and the SPIDERS technical team would like to acknowledge the following for help in the project: * Mike Hightower, who has been the key driving force for Energy Surety Microgrids * Juan Torres and Abbas Akhil, who developed the concept of microgrids for military installations * Merrill Smith, U.S. Department of Energy SPIDERS Program Manager * Ross Roley and Rich Trundy from U.S. Pacific Command * Bill Waugaman and Bill Beary from U.S. Northern Command * Melanie Johnson and Harold Sanborn of the U.S. Army Corps of Engineers Construc- tion Engineering Research Laboratory * Experts from the National Renewable Energy Laboratory, Idaho National Laboratory, Oak Ridge National Laboratory, and Pacific Northwest National Laboratory

  2. Analytical Chemistry Core Capability Assessment - Preliminary Report

    Energy Technology Data Exchange (ETDEWEB)

    Barr, Mary E. [Los Alamos National Laboratory; Farish, Thomas J. [Los Alamos National Laboratory

    2012-05-16

    The concept of 'core capability' can be nebulous one. Even at a fairly specific level, where core capability equals maintaining essential services, it is highly dependent upon the perspective of the requestor. Samples are submitted to analytical services because the requesters do not have the capability to conduct adequate analyses themselves. Some requests are for general chemical information in support of R and D, process control, or process improvement. Many analyses, however, are part of a product certification package and must comply with higher-level customer quality assurance requirements. So which services are essential to that customer - just those for product certification? Does the customer also (indirectly) need services that support process control and improvement? And what is the timeframe? Capability is often expressed in terms of the currently utilized procedures, and most programmatic customers can only plan a few years out, at best. But should core capability consider the long term where new technologies, aging facilities, and personnel replacements must be considered? These questions, and a multitude of others, explain why attempts to gain long-term consensus on the definition of core capability have consistently failed. This preliminary report will not try to define core capability for any specific program or set of programs. Instead, it will try to address the underlying concerns that drive the desire to determine core capability. Essentially, programmatic customers want to be able to call upon analytical chemistry services to provide all the assays they need, and they don't want to pay for analytical chemistry services they don't currently use (or use infrequently). This report will focus on explaining how the current analytical capabilities and methods evolved to serve a variety of needs with a focus on why some analytes have multiple analytical techniques, and what determines the infrastructure for these analyses. This

  3. BASE Flexible Array Preliminary Lithospheric Structure Analysis

    Science.gov (United States)

    Yeck, W. L.; Sheehan, A. F.; Anderson, M. L.; Siddoway, C. S.; Erslev, E.; Harder, S. H.; Miller, K. C.

    2009-12-01

    The Bighorns Arch Seismic Experiment (BASE) is a Flexible Array experiment integrated with EarthScope. The goal of BASE is to develop a better understanding of how basement-involved foreland arches form and what their link is to plate tectonic processes. To achieve this goal, the crustal structure under the Bighorn Mountain range, Bighorn Basin, and Powder River Basin of northern Wyoming and southern Montana are investigated through the deployment of 35 broadband seismometers, 200 short period seismometers, 1600 “Texan” instruments using active sources and 800 “Texan” instruments monitoring passive sources, together with field structural analysis of brittle structures. The novel combination of these approaches and anticipated simultaneous data inversion will give a detailed structural crustal image of the Bighorn region at all levels of the crust. Four models have been proposed for the formation of the Bighorn foreland arch: subhorizontal detachment within the crust, lithospheric buckling, pure shear lithospheric thickening, and fault blocks defined by lithosphere-penetrating thrust faults. During the summer of 2009, we deployed 35 broadband instruments, which have already recorded several magnitude 7+ teleseismic events. Through P wave receiver function analysis of these 35 stations folded in with many EarthScope Transportable Array stations in the region, we present a preliminary map of the Mohorovicic discontinuity. This crustal map is our first test of how the unique Moho geometries predicted by the four hypothesized models of basement involved arches fit seismic observations for the Bighorn Mountains. In addition, shear-wave splitting analysis for our first few recorded teleseisms helps us determine if strong lithospheric deformation is preserved under the range. These analyses help lead us to our final goal, a complete 4D (3D spatial plus temporal) lithospheric-scale model of arch formation which will advance our understanding of the mechanisms

  4. Preliminary classification criteria for the cryoglobulinaemic vasculitis

    Science.gov (United States)

    De Vita, S; Soldano, F; Isola, M; Monti, G; Gabrielli, A; Tzioufas, A; Ferri, C; Ferraccioli, G F; Quartuccio, L; Corazza, L; De Marchi, G; Casals, M Ramos; Voulgarelis, M; Lenzi, M; Saccardo, F; Fraticelli, P; Mascia, M T; Sansonno, D; Cacoub, P; Tomsic, M; Tavoni, A; Pietrogrande, M; Zignego, A L; Scarpato, S; Mazzaro, C; Pioltelli, P; Steinfeld, S; Lamprecht, P; Bombardieri, S; Galli, M

    2011-01-01

    Background To develop preliminary classification criteria for the cryoglobulinaemic syndrome or cryoglobulinaemic vasculitis (CV). Methods Study part I developed a questionnaire for CV to be included in the formal, second part (study part II). Positivity of serum cryoglobulins was defined by experts as an essential condition for CV classification. In study part II, a core set of classification items (questionnaire, clinical and laboratory items, as agreed) was tested in three groups of patients and controls—that is, group A (new patients with the CV), group B (controls with serum cryoglobulins but lacking CV) and group C (controls without serum cryoglobulins but with features which can be observed in CV). Results In study part I (188 cases, 284 controls), a positive response to at least two of three selected questions showed a sensitivity of 81.9% and a specificity of 83.5% for CV. This questionnaire was employed and validated in study part II, which included 272 patients in group A and 228 controls in group B. The final classification criteria for CV, by pooling data from group A and group B, required the positivity of questionnaire plus clinical, questionnaire plus laboratory, or clinical plus laboratory items, or all the three, providing a sensitivity of 88.5% and a specificity of 93.6% for CV. By comparing data in group A versus group C (425 controls), the same classification criteria showed a sensitivity 88.5% and a specificity 97.0% for CV. Conclusion Classification criteria for CV were developed, and now need validation. PMID:21571735

  5. Preliminary Evaluation of a New Cosmology Curriculum

    Science.gov (United States)

    Coble, Kimberly A.; Martin, Dominique; Hayes, Patrycia; Targett, Tom; Bailey, Janelle M.; Cominsky, Lynn R.

    2015-01-01

    Informed by our research on student understanding of cosmology, The Big Ideas in Cosmology is an immersive set of web-based learning modules that integrates text, figures, and visualizations with short and long interactive tasks and real cosmological data. This enables the transformation of general education astronomy and cosmology classes from primarily lecture and book-based courses to a more engaging format that builds important STEM skills.During the spring 2014 semester, we field-tested a subset of chapters with the general education astronomy and cosmology classes at Sonoma State University in a flipped-classroom format. We administered pre and post content and attitude assessments in the two flipped classes as well as two lecture classes. The majority of cosmology students had taken astronomy before whereas the astronomy students had not.When switching to an active mode of learning (e.g., flipped classroom instead of lecture), many instructors report pushback from students. We saw this effect from students in course evaluations, who reported dissatisfaction with "having to do more work." However, the students in the flipped section in astronomy made greater gains on the multiple choice content assessment than the students in either of the two lecture sections. On the attitude assessment (the CLASS), the cosmology students made a small shift toward more expert-like opinions. Preliminary results from open-ended content surveys indicate that, prior to instruction, students had difficulty answering 'why' or 'how do we know' questions; that post-instruction, students are less likely to respond "I don't know" or to leave an answer blank; and that students using the modules made gains in their content knowledge.Module development was supported by NASA ROSES E/PO Grant #NNXl0AC89G, the Illinois Space Grant Consortium, the Fermi E/PO program, Sonoma State University's Space Science Education and Public Outreach Group, and Great River Technology

  6. Immersive simulation of hearing loss and auditory prostheses

    Science.gov (United States)

    Zurek, Patrick M.; Desloge, Joseph G.

    2004-05-01

    Simulation of hearing loss is useful for demonstrating the communication challenges facing hearing-impaired people. However, current simulations, most of which are only recordings, do not actually elevate thresholds; i.e., they do not simulate hearing loss, per se. The hearing loss simulator described in this talk is immersive; the user's detection thresh- olds for ambient sounds are shifted by a prescribed degree. This threshold shift is achieved through a combination of passive attenuation (from muff-type hearing protectors) and additive masking noise (introduced by within-muff earphones). Acoustic signals picked up by microphones near each ear are processed through bandpass AGC channels and delivered via the earphones to complete the simulation of frequency-dependent hearing loss and loudness recruitment. Preliminary results validating the accuracy of specified threshold shift will be presented, along with speech-reception data comparing simulated with actual hearing losses. Subjective reactions of users engaged in one-on-one conversation suggest that strong feelings of communication disability are engendered by even moderate degrees of simulated hearing loss. The system, which is capable of simulating any degree of recruiting hearing loss along with hearing aids or cochlear implants, can provide effective interactive demonstrations of both auditory communication handicap and rehabilitation options. [Work supported by NIDCD.

  7. Full scale computer simulators in anesthesia training and evaluation.

    Science.gov (United States)

    Wong, Anne K

    2004-05-01

    With the advent of competency-based curriculum, technology such as full scale computer simulators have acquired an increasingly important role in anesthesia both in training and evaluation. This article reviews the current role of full scale computer simulators in teaching and evaluation in anesthesia. This review draws from existing anesthesia and medical education literature in order to examine and assess the current role of full scale computer simulators in anesthesia education today. The last decade has witnessed a major increase in the use of full scale computer simulators in anesthesia. Many applications have been found for these simulators including teaching and training, evaluation and research. Despite the increasing use and application of full scale computers in anesthesia in the area of teaching and training, definitive studies evaluating its cost effectiveness, its efficacy compared to traditional training methods or its impact on patient outcome are still pending. Although there is some preliminary evidence of reliability and validity in using the simulator to evaluate clinical competence, development in this area has not progressed enough to justify its use in formal, summative evaluation of competence in anesthesia at this time. As technology acquires an increasingly important role in medical education, full scale computer simulators represent an exciting potential in anesthesia. However, the full potential and role of simulators in anesthesia is still in development and will require a dovetailing of clinical theory and practice with current research in medical education.

  8. Fast 3D seismic wave simulations of 24 August 2016 Mw 6.0 central Italy earthquake for visual communication

    Directory of Open Access Journals (Sweden)

    Emanuele Casarotti

    2016-12-01

    Full Text Available We present here the first application of the fast reacting framework for 3D simulations of seismic wave propagation generated by earthquakes in the Italian region with magnitude Mw 5. The driven motivation is to offer a visualization of the natural phenomenon to the general public but also to provide preliminary modeling to expert and civil protection operators. We report here a description of this framework during the emergency of 24 August 2016 Mw 6.0 central Italy Earthquake, a discussion on the accuracy of the simulation for this seismic event and a preliminary critical analysis of the visualization structure and of the reaction of the public.

  9. Process simulation using WITNESS

    CERN Document Server

    Al-Aomar, Raid; Ulgen, Onur M

    2015-01-01

    Teaches basic and advanced modeling and simulation techniques to both undergraduate and postgraduate students and serves as a practical guide and manual for professionals learning how to build simulation models using WITNESS, a free-standing software package. This book discusses the theory behind simulation and demonstrates how to build simulation models with WITNESS. The book begins with an explanation of the concepts of simulation modeling and a "guided tour" of the WITNESS modeling environment. Next, the authors cover the basics of building simulation models using WITNESS and mode

  10. Combine Harvester Simulator

    DEFF Research Database (Denmark)

    Vilmann, Ole; Sørlie, James Arnold

    1999-01-01

    A simulator for training pilots in the operation of a modern high-tech combine harvester is presented. The new simulator application is based on DMI´s well-known DMS maritime simulator architecture. Two major challenges have been encountered in the development of the simulator: 1) interfacing...... the simulator software and the harvester hardware, and 2) the visual image generation system. Aims of the project have been to promote technology transfer from DMI´s maritime simulator to new application areas, to develop a state-of-the-art pilot training environment, and to utilise the state......-of-the-art in objec-oriented graphics programming technologies....

  11. Nuclear Reactor Component Code CUPID-I: Numerical Scheme and Preliminary Assessment Results

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Hyoung Kyu; Jeong, Jae Jun; Park, Ik Kyu; Kim, Jong Tae; Yoon, Han Young

    2007-12-15

    A component scale thermal hydraulic analysis code, CUPID (Component Unstructured Program for Interfacial Dynamics), is being developed for the analysis of components of a nuclear reactor, such as reactor vessel, steam generator, containment, etc. It adopted three-dimensional, transient, two phase and three-field model. In order to develop the numerical schemes for the three-field model, various numerical schemes have been examined including the SMAC, semi-implicit ICE, SIMPLE, Row Scheme and so on. Among them, the ICE scheme for the three-field model was presented in the present report. The CUPID code is utilizing unstructured mesh for the simulation of complicated geometries of the nuclear reactor components. The conventional ICE scheme that was applied to RELAP5 and COBRA-TF, therefore, were modified for the application to the unstructured mesh. Preliminary calculations for the unstructured semi-implicit ICE scheme have been conducted for a verification of the numerical method from a qualitative point of view. The preliminary calculation results showed that the present numerical scheme is robust and efficient for the prediction of phase changes and flow transitions due to a boiling and a flashing. These calculation results also showed the strong coupling between the pressure and void fraction changes. Thus, it is believed that the semi-implicit ICE scheme can be utilized for transient two-phase flows in a component of a nuclear reactor.

  12. Light ion production for a future radiobiological facility at CERN: preliminary studies.

    Science.gov (United States)

    Stafford-Haworth, Joshua; Bellodi, Giulia; Küchler, Detlef; Lombardi, Alessandra; Röhrich, Jörg; Scrivens, Richard

    2014-02-01

    Recent medical applications of ions such as carbon and helium have proved extremely effective for the treatment of human patients. However, before now a comprehensive study of the effects of different light ions on organic targets has not been completed. There is a strong desire for a dedicated facility which can produce ions in the range of protons to neon in order to perform this study. This paper will present the proposal and preliminary investigations into the production of light ions, and the development of a radiobiological research facility at CERN. The aims of this project will be presented along with the modifications required to the existing linear accelerator (Linac3), and the foreseen facility, including the requirements for an ion source in terms of some of the specification parameters and the flexibility of operation for different ion types. Preliminary results from beam transport simulations will be presented, in addition to some planned tests required to produce some of the required light ions (lithium, boron) to be conducted in collaboration with the Helmholtz-Zentrum für Materialien und Energie, Berlin.

  13. Preliminary Design Report of Fluid System of PDRC Performance Test Facility

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Tae-Ho; Eoh, Jae-Hyuk; Seong, Seung-Hwan; Han, Ji-Woong; Choi, Byoung-Hae; Kim, Seong-O

    2008-10-15

    PDRC (Passive Decay Heat Removal Circuit) is a safety grade passive residual heat removal system of KALIMER-600. In order to assess the long- and short-term cooling capabilities of PDRC and produce the experimental data for the verification of the performance and safety analysis codes, PDRC performance test was planned for. In this study, the overall design requirements and the preliminary design data for the fluid system of test facility are presented. The fluid system of the facility is composed of the primary heat transport system, the PDRC, the IHX air cooling system and the sodium supply/purification system. The preliminarily designed facility is scaled-down to 1/4 for length, 1/400 for volume from the primary heat transport system and the PDRC of KALIMER-600 based on a reliable scaling method. It can simulate the cooling of primary heat transport system for the full temperature condition in case of the reactor and pump trips. The produced preliminary design data will be used in the future as the basic information for a detailed design, an establishment of experimental requirement and an assessment of the appropriateness of facility design.

  14. Testing the Preliminary X-33 Navigation System

    Science.gov (United States)

    Lomas, James J.; Mitchell, Daniel W.; Freestone, Todd M.; Lee, Charles; Lessman, Craig; Foster, Lee D. (Technical Monitor)

    2001-01-01

    The X-33 Reusable Launch Vehicle (RLV) must meet the demanding requirements of landing autonomously on a narrow landing strip following a flight that reaches an altitude of up to 200,000 feet and a speed in excess of Mach 9 with significant in-flight energy bleed-off maneuvers. To execute this flight regimen a highly reliable avionics system has been designed that includes three LN-100G Inertial Navigation System/Global Positioning System (INS/GPS) units as the primary navigation system for the X-33. NASA's Marshall Space Flight Center (MSFC) tested an INS/GPS system in real-time simulations to determine the ability of this navigation suite to meet the in flight and autonomous landing requirements of the X-33 RLV. A total of sixty-one open loop tests were performed to characterize the navigation accuracy of the LN-100G. Twenty-seven closed-loop tests were also performed to evaluate the performance of the X-33 Guidance, Navigation and Control (GN&C) algorithms with the real navigation hardware. These closed-loop tests were also designed to expose any integration or operational issues with the real-time X-33 vehicle simulation. Dynamic road tests of the INS/GPS were conducted by Litton to assess the performance of differential and nondifferential INS/GPS hybrid navigation solutions. The results of the simulations and road testing demonstrate that this novel solution is capable of meeting the demanding requirements of take-off, in-flight navigation, and autonomous landing of the X-33 RLV. This paper describes the test environment developed to stimulate the LN-100G and discusses the results of this test effort. This paper also presents recommendations for a navigation system suitable to an operational RLV system.

  15. A simulation environment for ITER PCS development

    Energy Technology Data Exchange (ETDEWEB)

    Walker, M.L., E-mail: walker@fusion.gat.com [General Atomics, P.O. Box 85608, San Diego, CA 92186-5608 (United States); Ambrosino, G.; De Tommasi, G. [CREATE/Università di Napoli Federcico II, Napoli (Italy); Humphreys, D.A. [General Atomics, P.O. Box 85608, San Diego, CA 92186-5608 (United States); Mattei, M. [Seconda Università di Napoli, Napoli (Italy); Neu, G.; Raupp, G.; Treutterer, W. [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, 85748 Garching (Germany); Winter, A. [ITER Organization, Route de Vinon-sur-Verdon, 13115 St. Paul-lez-Durance (France)

    2014-05-15

    Highlights: • Describes task to develop simulation tool to aid development/testing of ITER PCS. • Requirements and use cases and preliminary architecture have been delivered. • Detailed design is now being developed. • Provides overview of use cases and requirements. • Provides overview of architecture and status of development. - Abstract: A simulation environment known as the Plasma Control System Simulation Platform (PCSSP), specifically designed to support development of the ITER Plasma Control System (PCS), is currently under construction by an international team encompassing a cross-section of expertise in simulation and exception handling for plasma control. The proposed design addresses the challenging requirements of supporting the PCS design. This paper provides an overview of the PCSSP project and a discussion of some of the major features of its design. Plasma control for the ITER tokamak will be significantly more challenging than for existing fusion devices. An order of magnitude greater performance (e.g. [1,2]) is needed for some types of control, which together with limited actuator authority, implies that optimized individual controllers and nonlinear saturation logic are required. At the same time, consequences of control failure are significantly more severe, which implies a conflicting requirement for robust control. It also implies a requirement for comprehensive and robust exception handling. Coordinated control of multiple competing objectives with significant interactions, together with many shared uses of actuators to control multiple variables, implies that highly integrated control logic and shared actuator management will be required. It remains a challenge for the integrated technologies to simultaneously address these multiple and often competing requirements to be demonstrated on existing fusion devices and adapted for ITER in time to support its operational schedule. We describe ways in which the PCSSP will help address

  16. Preliminary study on assessment of nutrient transport in the Taihu Basin based on SWAT modeling

    Institute of Scientific and Technical Information of China (English)

    LAI; Geying; YU; Ge; GUI; Feng

    2006-01-01

    With the Taihu Basin as a study area, using the spatially distributed and mechanism-based SWAT model, preliminary simulations of nutrient transport in the Taihu Basin during the period of 1995~2002 has been carried out. The topography, soil, meteorology and land use with industrial point pollution discharge, the loss of agricultural fertilizers, urban sewerage, and livestock drainages were all considered in the boundary conditions of the simulations. The model was calibrated and validated against water quality monitoring data from 2001 to 2002. The results show that the annual total productions of nitrogen (TN) and phosphorus (TP) into Lake Taihu are 40000t and 2000t respectively. Nutrient from the Huxi Region is a major resource for Lake Taihu. The non-point source (surface source) pollution is the main form of catchment sources of nutrients into Lake Taihu,occupied TN 53% and TP 56% respectively. TN and TP nutrients from industrial point pollution discharge are 30% and 16%, and sewerage in both forms of point source and non-point source are TN 31% and TP 47%. Both the loss of agricultural fertilizers and livestock drainages from the catchment should be paid more attention as an important nutrient source. The results also show that SWAT is an effective model for the simulation of temporally and spatially nutrient changes and for the assessment of the trends in a catchment scale.

  17. Preliminary Characterization Results from the DebriSat Project

    Science.gov (United States)

    Rivero, M.; Shiotani, B.; Kleespies, J.; Toledo-Burdett, R.; Moraguez, M.; Carrasquila, M.; Fitz-Coy, N.; Liou, J.-C.; Sorge, M.; Huynh, T.

    2016-01-01

    The DebriSat project is a continuing effort sponsored by NASA and DoD to update existing break-up models using data obtained from two separate hypervelocity impact tests used to simulate on-orbit collisions. To protect the fragments resulting from the impact tests, "soft-catch" arenas made of polyurethane foam panels were utilized. After each impact test, the test chamber was cleaned and debris resulting from the catastrophic demise of the test article were collected and shipped to the University of Florida for post-impact processing. The post-impact processing activities include collecting, characterizing, and cataloging of the fragments. Since the impact tests, a team of students has been working to characterize the fragments in terms of their mass, size, shape, color and material content. The focus of the 20 months since the impact tests has been on the collection of 2 millimeters- and larger fragments resulting from impact test on the 56 kilogram-representative LEO (Low Earth Orbit) satellite referred to as DebriSat. To date we have recovered in excess of 115,000 fragments, 30,000 more than the prediction of 85,000 fragments from the existing model. We continue to collect fragments but have transitioned to the characterization phase of the post-impact activities. Since the start of the characterization phase, the focus has been to utilize automation to (i) expedite fragment characterization process and (ii) minimize human-in-the- loop. We have developed and implemented such automated processes; e.g., we have automated the data entry process to reduce operator errors during transcription of the measurement data. However, at all steps of the process, there is human oversight to ensure the integrity of the data. Additionally, we have developed and implemented repeatability and reproducibility tests to ensure that the instrumentation used in the characterization process is accurate and properly calibrated. In this paper, the implemented processes are described and

  18. Preliminary microphysical characterization of precipitation at ground over Antarctica coast

    Science.gov (United States)

    Roberto, Nicoletta; Adirosi, Elisa; Montopoli, Mario; Baldini, Luca; Dietrich, Stefano; Porcù, Federico

    2017-04-01

    The primary mass input of the Antarctic ice sheet is snow precipitation which is one of the most direct climatic indicators. Climatic model simulations of precipitations over Antarctica is an important task to assess the variation of ice sheet over long temporal scale. The main source of precipitation information in Antarctica regions derive from satellite observations. However, satellite measurements and products need to be calibrated and validated with observations from ground sensors. In spite of their key role, precipitation measurements at ground are scarce and not appropriate to provide the specific characteristic of precipitation particles that influence the scattering and absorption properties of ice particles. Recently, different stations in Antarctica (Princess Elizabeth, McMurdo, Mario Zucchelli) are equipping observatories for cloud and precipitation observations. The setup of the observatory at the Italian Station, Mario Zucchelli (MZ) plans to integrate the current instrumentation for weather measurements with other instruments specific for precipitation observations, in particular, a 24-GHz vertical pointing radar and a laser disdrometer Parsivel. The synergetic use of the set of instruments allows for characterizing precipitation and studying properties of Antarctic precipitation such as dimension, shapes, fall behavior, density of particles, particles size distribution, particles terminal velocity, reflectivity factor and including some information on their vertical extent. Last November, the OTT Parsivel disdrometer was installed on the roof of a logistic container (at 6 m of height) of the MZ station (Latitude 74° 41' 42" S; Longitude 164° 07' 23E") in the Terranova Bay. The disdrometer measures size and fall velocity of particles, passing through a laser matrix from which the Particle Size Distribution (PSD) is obtained. In addition, some products such as reflectivity factor, snow rate and snow accumulation can be inferred by properly

  19. Ride Motion Simulator (RMS)

    Data.gov (United States)

    Federal Laboratory Consortium — The RMS is a simulator designed for crew station and man-in-the-loop experimentation. The simulator immerses users in a synthetic battlefield to experience realistic...

  20. USU Patient Simulation Center

    Data.gov (United States)

    Federal Laboratory Consortium — he National Capital Area (NCA) Medical Simulation Center is a state-of-the-art training facility located near the main USU campus. It uses simulated patients (i.e.,...