The establishment and application of direct coupled electrostatic-structural field model in electrostatically controlled deployable membrane antenna

Science.gov (United States)

Gu, Yongzhen; Duan, Baoyan; Du, Jingli

2018-05-01

The electrostatically controlled deployable membrane antenna (ECDMA) is a promising space structure due to its low weight, large aperture and high precision characteristics. However, it is an extreme challenge to describe the coupled field between electrostatic and membrane structure accurately. A direct coupled method is applied to solve the coupled problem in this paper. Firstly, the membrane structure and electrostatic field are uniformly described by energy, considering the coupled problem is an energy conservation phenomenon. Then the direct coupled electrostatic-structural field governing equilibrium equations are obtained by energy variation approach. Numerical results show that the direct coupled method improves the computing efficiency by 36% compared with the traditional indirect coupled method with the same level accuracy. Finally, the prototype has been manufactured and tested and the ECDMA finite element simulations show good agreement with the experiment results as the maximum surface error difference is 6%.

Dynamic characteristics analysis of deployable space structures considering joint clearance

Science.gov (United States)

Li, Tuanjie; Guo, Jian; Cao, Yuyan

2011-04-01

The clearance in joints influences the dynamic stability and the performance of deployable space structures (DSS). A virtual experimental modal analysis (VEMA) method is proposed to deal with the effects of joint clearance and link flexibility on the dynamic characteristics of the DSS in this paper. The focus is on the finite element modeling of the clearance joint, VEMA and the modal parameters identification of the DSS. The finite element models (FEM) of the clearance joint and the deployable structure are established in ANSYS. The transient dynamic analysis is conducted to provide the time history data of excitation and response for the VEMA. The fast Fourier transform (FFT) technique is used to transform the data from time domain to frequency domain. The frequency response function is calculated to identify the modal parameters of the deployable structure. Experimental verification is provided to indicate the VEMA method is both a cost and time efficient approach to obtain the dynamic characteristics of the DSS. Finally, we analyze the effects of clearance size and gravity on the dynamic characteristics of the DSS. The analysis results indicate that the joint clearance and gravity strongly influence the dynamic characteristics of the DSS.

Joint Estimation of Multiple Precision Matrices with Common Structures.

Science.gov (United States)

Lee, Wonyul; Liu, Yufeng

Estimation of inverse covariance matrices, known as precision matrices, is important in various areas of statistical analysis. In this article, we consider estimation of multiple precision matrices sharing some common structures. In this setting, estimating each precision matrix separately can be suboptimal as it ignores potential common structures. This article proposes a new approach to parameterize each precision matrix as a sum of common and unique components and estimate multiple precision matrices in a constrained l 1 minimization framework. We establish both estimation and selection consistency of the proposed estimator in the high dimensional setting. The proposed estimator achieves a faster convergence rate for the common structure in certain cases. Our numerical examples demonstrate that our new estimator can perform better than several existing methods in terms of the entropy loss and Frobenius loss. An application to a glioblastoma cancer data set reveals some interesting gene networks across multiple cancer subtypes.

New Analysis and Theory of Deployable Folded Structures, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — A recently developed mathematical theory has great value for deployable space structures and in situ manufacture of large beams, panels, cylinders and other...

Deployable bamboo structure project: A building life-cycle report

Science.gov (United States)

Firdaus, Adrian; Prastyatama, Budianastas; Sagara, Altho; Wirabuana, Revian N.

2017-11-01

Bamboo is considered as a sustainable material in the world of construction, and it is vastly available in Indonesia. The general utilization of the material is increasingly frequent, however, its usage as a deployable structure-a recently-developed use of bamboo, is still untapped. This paper presents a report on a deployable bamboo structure project, covering the entire building life-cycle phase. The cycle encompasses the designing; fabrication; transportation; construction; operation and maintenance; as well as a plan for future re-use. The building is made of a configuration of the structural module, each being a folding set of bars which could be reduced in size to fit into vehicles for easy transportation. Each structural module was made of Gigantochloa apus bamboo. The fabrication, transportation, and construction phase require by a minimum of three workers. The fabrication and construction phase require three hours and fifteen minutes respectively. The building is utilized as cafeteria stands, the operation and maintenance phase started since early March 2017. The maintenance plan is scheduled on a monthly basis, focusing on the inspection of the locking mechanism element and the entire structural integrity. The building is designed to allow disassembly process so that it is reusable in the future.

New Analysis and Theory of Deployable Folded Structures, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — A recently developed mathematical folding theory has great value for deployable space structures and in situ manufacture of large beams, panels and cylinders. The...

Design and analysis of a deployable truss for the large modular mesh antenna

Science.gov (United States)

Meguro, Akira

This paper describes the design and deployment analysis for large deployable modular mesh antennas. Key design criteria are deployability, and the driving force and latching moment requirements. Reaction forces and moments due to mesh and cable network seriously influence the driving force. These forces and moments can be precisely estimated by means of analyzing the cable network using Cable Structure Analyzer (CASA). Deployment analysis is carried out using Dynamic Analysis and Design System (DADS). The influence of alignment errors on the driving reaction force can be eliminated by replacing the joint element with a spring element. The joint slop is also modeled using a discontinuous spring elements. Their design approach for three types of deployable modules and the deployment characterstics of three Bread-Board Models based on those designs are also presented. In order to study gravity effects on the deployment characteristics and the effects of the gravity compensation method, ground deployment analysis is carried out. A planned deployment test that will use aircraft parabolic flight to simulate a micro-gravity environment is also described.

Precise fabrication of X-band accelerating structure

International Nuclear Information System (INIS)

Higo, T.; Sakai, H.; Higashi, Y.; Koike, S.; Takatomi, T.

1994-01-01

An accelerating structure with a/λ=0.16 is being fabricated to study a precise fabrication method. A frequency control of each cell better than 10 -4 level is required to realize a detuned structure. The present machining level is nearly 1 MHz/11.4 GHz in relative frequency error, which just satisfies the above requirement. To keep this machining precision, the diffusion bonding technique is found preferable to join the cells. Various diffusion conditions were tried. The frequency change can be less than 1 MHz/11.4 GHz and it can be controlled well better than that. (author)

Optimum wireless sensor deployment scheme for structural health monitoring: a simulation study

International Nuclear Information System (INIS)

Liu, Chengyin; Fang, Kun; Teng, Jun

2015-01-01

With the rapid advancements in smart sensing technology and wireless communication technology, the wireless sensor network (WSN) offers an alternative solution to structural health monitoring (SHM). In WSNs, dense deployment of wireless nodes aids the identification of structural dynamic characteristics, while data transmission is a significant issue since wireless channels typically have a lower bandwidth and a limited power supply. This paper provides a wireless sensor deployment optimization scheme for SHM, in terms of both energy consumption and modal identification accuracy. A spherical energy model is established to formulate the energy consumption within a WSN. The optimal number of sensors and their locations are obtained through solving a multi-objective function with weighting factors on energy consumption and modal identification accuracy using a genetic algorithm (GA). Simulation and comparison results with traditional sensor deployment methods demonstrate the efficiency of the proposed optimization scheme. (paper)

Dynamics Analysis of Origami-Folded Deployable Space Structures with Elastic Hinges

Data.gov (United States)

National Aeronautics and Space Administration — The future of space exploration needs highly sophisticated deployable space structure technology in order to achieve the ambitious goals being set today. Several...

Design and Experimental Verification of Deployable/Inflatable Ultra-Lightweight Structures

Science.gov (United States)

Pai, P. Frank

2004-01-01

Because launch cost of a space structural system is often proportional to the launch volume and mass and there is no significant gravity in space, NASA's space exploration programs and various science missions have stimulated extensive use of ultra-lightweight deployable/inflatable structures. These structures are named here as Highly Flexible Structures (HFSs) because they are designed to undergo large displacements, rotations, and/or buckling without plastic deformation under normal operation conditions. Except recent applications to space structural systems, HFSs have been used in many mechanical systems, civil structures, aerospace vehicles, home appliances, and medical devices to satisfy space limitations, provide special mechanisms, and/or reduce structural weight. The extensive use of HFSs in today's structural engineering reveals the need of a design and analysis software and a database system with design guidelines for practicing engineers to perform computer-aided design and rapid prototyping of HFSs. Also to prepare engineering students for future structural engineering requires a new and easy-to- understand method of presenting the complex mathematics of the modeling and analysis of HFSs. However, because of the high flexibility of HFSs, many unique challenging problems in the modeling, design and analysis of HFSs need to be studied. The current state of research on HFSs needs advances in the following areas: (1) modeling of large rotations using appropriate strain measures, (2) modeling of cross-section warpings of structures, (3) how to account for both large rotations and cross- section warpings in 2D (two-dimensional) and 1D structural theories, (4) modeling of thickness thinning of membranes due to inflation pressure, pretension, and temperature change, (5) prediction of inflated shapes and wrinkles of inflatable structures, (6) development of efficient numerical methods for nonlinear static and dynamic analyses, and (7) filling the gap between

Deployment Repeatability

Science.gov (United States)

2016-04-01

evaluating the deployment repeatability builds upon the testing or analysis of deployment kinematics (Chapter 6) and adds repetition. Introduction...material yield or failure during a test. For the purposes of this chapter, zero shift will refer to permanent changes in the structure, while reversible ...the content of other chapters in this book: Gravity Compensation (Chapter 4) and Deployment Kinematics and Dynamics (Chapter 6). Repeating the

Deployable structures using bistable reeled composites

Science.gov (United States)

Daton-Lovett, Andrew J.; Compton-Bishop, Quentin M.; Curry, Richard G.

2000-06-01

This paper describes an innovative, patented use of composite materials developed by RolaTube Technology Ltd. to make smart deployable structures. Bi-stable reeled composites (BRCs) can alternate between two stable forms; that of a strong, rigid structure and that of a compact coil of flat-wound material. Bi-stability arises as a result of the manipulation of Poisson's ratio and isotropy in the various layers of the material. BRCs are made of fiber- reinforced composite materials, most often with a thermoplastic matrix. A range of fibers and polymer matrices can be used according to the requirements of the operating environment. Samples of a BRC structure were constructed using layers of unidirectional, fiber-reinforced thermoplastic sheet with the layers at different angles. The whole assembly was then consolidated under conditions of elevated temperature and pressure. The properties of the BRC are described and the result of a series of experiments performed on the sample to determine the tensile strength of the BRC structure are reported. A full analysis using finite element methods is being undertaken in collaboration with the University of Cambridge, England. The first commercial use has been to fabricate boom and drive mechanisms for the remote inspection of industrial plant.

Deployment of spatial attention to a structural framework: exogenous (alerting) and endogenous (goal-directed) factors.

Science.gov (United States)

Jefferies, Lisa N; Di Lollo, Vincent

2017-10-01

The main question examined in the present work was whether spatial attention can be deployed to an appropriate structural framework not only endogenously when the framework is displayed continuously, as in previous work, but also exogenously, when it is displayed transiently 100 ms before the target. The results of five experiments answered that question in the negative. We found that the onset transient triggered by a brief presentation of the structural framework did enhance the response to the upcoming target. That enhancement, however, was due not to the framework itself but to the alerting effect produced by its sudden onset, witness the finding that the same enhancement was produced by an onset transient triggered by a featureless stimulus (i.e., by a brief dimming of the entire screen, in the absence of a structural framework). We conclude that spatial attention can be deployed to the region demarcated by a structural framework when it is deployed endogenously but not when it is deployed exogenously. A theoretical account of the results is proposed in terms of the temporal dynamics of the locus cœruleus/norepinephrine neuromodulatory system.

Joint Tomographic Imaging of 3-­-D Density Structure Using Cosmic Ray Muons and High-­-Precision Gravity Data

Science.gov (United States)

Rowe, C. A.; Guardincerri, E.; Roy, M.; Dichter, M.

2015-12-01

As part of the CO2 reservoir muon imaging project headed by the Pacific Northwest National Laboraory (PNNL) under the U.S. Department of Energy Subsurface Technology and Engineering Research, Development, and Demonstration (SubTER) iniative, Los Alamos National Laboratory (LANL) and the University of New Mexico (UNM) plan to leverage the recently decommissioned and easily accessible Tunnel Vault on LANL property to test the complementary modeling strengths of muon radiography and high-precision gravity surveys. This tunnel extends roughly 300 feet into the hillside, with a maximum depth below the surface of approximately 300 feet. We will deploy LANL's Mini Muon Tracker (MMT), a detector consisting of 576 drift tubes arranged in alternating parallel planes of orthogonally oriented tubes. This detector is capable of precise determination of trajectories for incoming muons with angular resolution of a few milliradians. We will deploy the MMT at several locations within the tunnel, to obtain numerous crossing muon trajectories and permit a 3D tomographic image of the overburden to be built. In the same project, UNM will use a Scintrex digital gravimeter to collect high-precision gravity data from a dense grid on the hill slope above the tunnel as well as within the tunnel itself. This will provide both direct and differential gravity readings for density modeling of the overburden. By leveraging detailed geologic knowledge of the canyon and the lithology overlying the tunnel, as well as the structural elements, elevations and blueprints of the tunnel itself, we will evaluate the muon and gravity data both independently and in a simultaneous, joint inversion to build a combined 3D density model of the overburden.

Structurally uniform and atomically precise carbon nanostructures

Science.gov (United States)

Segawa, Yasutomo; Ito, Hideto; Itami, Kenichiro

2016-01-01

Nanometre-sized carbon materials consisting of benzene units oriented in unique geometric patterns, hereafter named nanocarbons, conduct electricity, absorb and emit light, and exhibit interesting magnetic properties. Spherical fullerene C60, cylindrical carbon nanotubes and sheet-like graphene are representative forms of nanocarbons, and theoretical simulations have predicted several exotic 3D nanocarbon structures. At present, synthetic routes to nanocarbons mainly lead to mixtures of molecules with a range of different structures and properties, which cannot be easily separated or refined into pure forms. Some researchers believe that it is impossible to synthesize these materials in a precise manner. Obtaining ‘pure’ nanocarbons is a great challenge in the field of nanocarbon science, and the construction of structurally uniform nanocarbons, ideally as single molecules, is crucial for the development of functional materials in nanotechnology, electronics, optics and biomedical applications. This Review highlights the organic chemistry approach — more specifically, bottom-up construction with atomic precision — that is currently the most promising strategy towards this end.

Self Deployable Ultra-Lightweight Modular Unit for Habitat Structural Applications, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Space deployable and rigidizable structures which are ultra-lightweight, and have high rigidity, space durability, and high impact resistance are desirable to...

Precise stacking and bonding technology for RDDS structure

International Nuclear Information System (INIS)

Higo, T; Toge, N.; Suzuki, T.

2000-01-01

The X-band accelerating structures called RDDS1 (Rounded Dumped Detuned Structure) for the linear collider have been developed. The main body of RDDS1 was successfully fabricated in Japan (KEK, IHI). We established basic fabrication techniques through the development of prototype structures including RDDS1. The precise stacking and bonding technologies for RDDS structure are presented in this paper. (author)

Designing of self-deploying origami structures using geometrically misaligned crease patterns.

Science.gov (United States)

Saito, Kazuya; Tsukahara, Akira; Okabe, Yoji

2016-01-01

Usually, origami-based morphing structures are designed on the premise of 'rigid folding', i.e. the facets and fold lines of origami can be replaced with rigid panels and ideal hinges, respectively. From a structural mechanics viewpoint, some rigid-foldable origami models are overconstrained and have negative degrees of freedom (d.f.). In these cases, the singularity in crease patterns guarantees their rigid foldability. This study presents a new method for designing self-deploying origami using the geometrically misaligned creases. In this method, some facets are replaced by 'holes' such that the systems become a 1-d.f. mechanism. These perforated origami models can be folded and unfolded similar to rigid-foldable (without misalignment) models because of their d.f. focusing on the removed facets, the holes will deform according to the motion of the frame of the remaining parts. In the proposed method, these holes are filled with elastic parts and store elastic energy for self-deployment. First, a new extended rigid-folding simulation technique is proposed to estimate the deformation of the holes. Next, the proposed method is applied on arbitrary-size quadrilateral mesh origami. Finally, by using the finite-element method, the authors conduct numerical simulations and confirm the deployment capabilities of the models.

High-Temperature Superconductors as Electromagnetic Deployment and Support Structures in Spacecraft. [NASA NIAC Phase I

Science.gov (United States)

Getliffe, Gwendolyn V.; Inamdar, Niraj K.; Masterson, Rebecca; Miller, David W.

2012-01-01

This report, concluding a one-year NIAC Phase I study, describes a new structural and mechanical technique aimed at reducing the mass and increasing the deployed-to-stowed length and volume ratios of spacecraft systems. This technique uses the magnetic fields generated by electrical current passing through coils of high-temperature superconductors (HTSs) to support spacecraft structures and deploy them to operational configurations from their stowed positions inside a launch vehicle fairing.

Performance analysis, quality function deployment and structured methods

Science.gov (United States)

Maier, M. W.

Quality function deployment, (QFD), an approach to synthesizing several elements of system modeling and design into a single unit, is presented. Behavioral, physical, and performance modeling are usually considered as separate aspects of system design without explicit linkages. Structured methodologies have developed linkages between behavioral and physical models before, but have not considered the integration of performance models. QFD integrates performance models with traditional structured models. In this method, performance requirements such as cost, weight, and detection range are partitioned into matrices. Partitioning is done by developing a performance model, preferably quantitative, for each requirement. The parameters of the model become the engineering objectives in a QFD analysis and the models are embedded in a spreadsheet version of the traditional QFD matrices. The performance model and its parameters are used to derive part of the functional model by recognizing that a given performance model implies some structure to the functionality of the system.

Conceptual Design of Deployment Structure of Morphing Nose Cone

Directory of Open Access Journals (Sweden)

Junlan Li

2013-01-01

Full Text Available For a reusable space vehicle or a missile, the shape of the nose cone has a significant effect on the drag of the vehicle. In this paper, the concept of morphing nose cone is proposed to reduce the drag when the reentry vehicle flies back into the atmosphere. The conceptual design of the structure of morphing nose cone is conducted. Mechanical design and optimization approach are developed by employing genetic algorithm to find the optimal geometric parameters of the morphing structure. An example is analyzed by using the proposed method. The results show that optimal solution supplies the minimum position error. The concept of morphing nose cone will provide a novel way for the drag reduction of reentry vehicle. The proposed method could be practically used for the design and optimization of the deployable structure of morphing nose cone.

Non-traditional Infrasound Deployment

Science.gov (United States)

McKenna, M. H.; McComas, S.; Simpson, C. P.; Diaz-Alvarez, H.; Costley, R. D.; Hayward, C.; Golden, P.; Endress, A.

2017-12-01

Historically, infrasound arrays have been deployed in rural environments where anthropological noise sources are limited. As interest in monitoring low energy sources at local distances grows in the infrasound community, it will be vital to understand how to monitor infrasound sources in an urban environment. Arrays deployed in urban centers have to overcome the decreased signal-to-noise ratio and reduced amount of real estate available to deploy an array. To advance the understanding of monitoring infrasound sources in urban environments, local and regional infrasound arrays were deployed on building rooftops on the campus at Southern Methodist University (SMU), and data were collected for one seasonal cycle. The data were evaluated for structural source signals (continuous-wave packets), and when a signal was identified, the back azimuth to the source was determined through frequency-wavenumber analysis. This information was used to identify hypothesized structural sources; these sources were verified through direct measurement and dynamic structural analysis modeling. In addition to the rooftop arrays, a camouflaged infrasound sensor was installed on the SMU campus and evaluated to determine its effectiveness for wind noise reduction. Permission to publish was granted by Director, Geotechnical and Structures Laboratory.

Adopting Continuous Delivery and Deployment: Impacts on Team Structures, Collaboration and Responsibilities

DEFF Research Database (Denmark)

Shahin, Mojtaba; Zahedi, Mansooreh; Babar, Muhammad Ali

2017-01-01

Context: Continuous Delivery and Deployment (CD) practices aim to deliver software features more frequently and reliably. While some efforts have been made to study different aspects of CD practices, a little empirical work has been reported on the impact of CD on team structures, collaboration a...

Local deformation method for measuring element tension in space deployable structures

Directory of Open Access Journals (Sweden)

Belov Sergey

2017-01-01

Full Text Available The article describes the local deformation method to determine the tension of cord and thin membrane elements in space deployable structure as antenna reflector. Possible measuring instrument model, analytical and numerical solutions and experimental results are presented. The boundary effects on measurement results of metallic mesh reflector surface tension are estimated. The study case depicting non-uniform reflector surface tension is considered.

Importance of structural damping in the dynamic analysis of compliant deployable structures

Science.gov (United States)

Dewalque, Florence; Rochus, Pierre; Brüls, Olivier

2015-06-01

Compliant mechanisms such as tape springs are often used on satellites to deploy appendices, e.g. solar panels, antennas, telescopes and solar sails. Their main advantage comes from the fact that their motion results from the elastic deformation of structural components and the absence of actuators or external energy sources. The mechanical behaviour of a tape spring is intrinsically complex and nonlinear involving buckling, hysteresis and self-locking phenomena. In the majority of the previous works, dynamic simulations were performed without any physical representation of the structural damping. These simulations could be successfully achieved because of the presence of numerical damping in the transient solver. However, in this case, the dynamic response turns out to be quite sensitive to the amount of numerical dissipation, so that the predictive capabilities of the model are questionable. In this work based on numerical case studies, we show that the dynamic simulation of a tape spring can be made less sensitive to numerical parameters when the structural dissipation is taken into account.

Deployment of a multi-link flexible structure

Science.gov (United States)

Na, Kyung-Su; Kim, Ji-Hwan

2006-06-01

Deployment of a multi-link beam structure undergoing locking is analyzed in the Timoshenko beam theory. In the modeling of the system, dynamic forces are assumed to be torques and restoring forces due to the torsion spring at each joint. Hamilton's principle is used to determine the equations of motion and the finite element method is adopted to analyze the system. Newmark time integration and Newton-Raphson iteration methods are used to solve for the non-linear equations of motion at each time step. The locking at the joints of the multi-link flexible structure is analyzed by the momentum balance method. Numerical results are compared with the previous experimental data. The angles and angular velocities of each joint, tip displacement, and velocity of each link are investigated to study the motions of the links at each time step. To analyze the effect of thickness on the motion of the link, the angle and the tip displacement of each link are compared according to the various slenderness ratios. Additionally, in order to investigate the effect of shear, the tip displacements of a Timoshenko beam are compared with those of an Euler-Bernoulli beam.

Morphing structures using soft polymers for active deployment

International Nuclear Information System (INIS)

Daynes, Stephen; Grisdale, Amy; Trask, Richard; Seddon, Annela

2014-01-01

In this study, we take inspiration from morphing strategies observed in nature, origami design and stiffness tailoring principles in engineering, to develop a thin walled, low cost, bistable cell geometry capable of reversibly unfolding from a flat configuration to a highly textured configuration. Finite element analysis was used to model the cell deployment and capture the experimentally observed bistability of the reinforced silicone elastomer. Through the combination of flexible elastomers with locally reinforced regions enables a highly tailorable and controllable deployment response. These cells are bistable allowing them to maintain their shape when either deployed or retracted without sustained actuation. It is proposed that such deployable cells with reversible surfaces and texture change can be used as a means of adaptive camouflage. (fast track communication)

Precise Truss Assembly Using Commodity Parts and Low Precision Welding

Science.gov (United States)

Komendera, Erik; Reishus, Dustin; Dorsey, John T.; Doggett, W. R.; Correll, Nikolaus

2014-01-01

Hardware and software design and system integration for an intelligent precision jigging robot (IPJR), which allows high precision assembly using commodity parts and low-precision bonding, is described. Preliminary 2D experiments that are motivated by the problem of assembling space telescope optical benches and very large manipulators on orbit using inexpensive, stock hardware and low-precision welding are also described. An IPJR is a robot that acts as the precise "jigging", holding parts of a local structure assembly site in place, while an external low precision assembly agent cuts and welds members. The prototype presented in this paper allows an assembly agent (for this prototype, a human using only low precision tools), to assemble a 2D truss made of wooden dowels to a precision on the order of millimeters over a span on the order of meters. The analysis of the assembly error and the results of building a square structure and a ring structure are discussed. Options for future work, to extend the IPJR paradigm to building in 3D structures at micron precision are also summarized.

Self-centering fiber alignment structures for high-precision field installable single-mode fiber connectors

Science.gov (United States)

Van Erps, Jürgen; Ebraert, Evert; Gao, Fei; Vervaeke, Michael; Berghmans, Francis; Beri, Stefano; Watté, Jan; Thienpont, Hugo

2014-05-01

There is a steady increase in the demand for internet bandwidth, primarily driven by cloud services and high-definition video streaming. Europe's Digital Agenda states the ambitious objective that by 2020 all Europeans should have access to internet at speeds of 30Mb/s or above, with 50% or more of households subscribing to connections of 100Mb/s. Today however, internet access in Europe is mainly based on the first generation of broadband, meaning internet accessed over legacy telephone copper and TV cable networks. In recent years, Fiber-To-The-Home (FTTH) networks have been adopted as a replacement of traditional electrical connections for the `last mile' transmission of information at bandwidths over 1Gb/s. However, FTTH penetration is still very low (economies. The main reason for this is the high deployment cost of FTTH networks. Indeed, the success and adoption of optical access networks critically depend on the quality and reliability of connections between optical fibers. In particular a further reduction of insertion loss of field- installable connectors must be achieved without a significant increase in component cost. This requires precise alignment of fibers that can differ in terms of ellipticity, eccentricity or diameter and seems hardly achievable using today's widespread ferrule-based alignment systems. In this paper, we present a field-installable connector based on deflectable/compressible spring structures, providing a self-centering functionality for the fiber. This way, it can accommodate for possible fiber cladding diameter variations (the tolerance on the cladding diameter of G.652 fiber is typically +/-0.7μm). The mechanical properties of the cantilever are derived through an analytical approximation and a mathematical model of the spring constant, and finite element-based simulations are carried out to find the maximum first principal stress as well as the stress distribution distribution in the fiber alignment structure. Elastic

High-precision optical systems with inexpensive hardware: a unified alignment and structural design approach

Science.gov (United States)

Winrow, Edward G.; Chavez, Victor H.

2011-09-01

High-precision opto-mechanical structures have historically been plagued by high costs for both hardware and the associated alignment and assembly process. This problem is especially true for space applications where only a few production units are produced. A methodology for optical alignment and optical structure design is presented which shifts the mechanism of maintaining precision from tightly toleranced, machined flight hardware to reusable, modular tooling. Using the proposed methodology, optical alignment error sources are reduced by the direct alignment of optics through their surface retroreflections (pips) as seen through a theodolite. Optical alignment adjustments are actualized through motorized, sub-micron precision actuators in 5 degrees of freedom. Optical structure hardware costs are reduced through the use of simple shapes (tubes, plates) and repeated components. This approach produces significantly cheaper hardware and more efficient assembly without sacrificing alignment precision or optical structure stability. The design, alignment plan and assembly of a 4" aperture, carbon fiber composite, Schmidt-Cassegrain concept telescope is presented.

ISIS Child Soldiers in Syria: The Structural and Predatory Recruitment, Enlistment, Pre-Training Indoctrination, Training, and Deployment

Directory of Open Access Journals (Sweden)

Asaad Almohammad

2018-02-01

Full Text Available Research on the engagement of children with the so-called Islamic State (a.k.a. ISIS relies heavily on the analysis of obtained ISIS documents and ISIS-disseminated propaganda, leaving major elements of the recruitment and deployment process uncovered. Such ambiguities hinder future efforts aimed at dealing with ISIS’ child soldiers. As such, an intensive effort to compile data using interviews and naturalistic observations across ISIS-held territories in Syria was made to exhaustively explore the process of child recruitment and deployment by ISIS. Findings suggest that there are two methods of recruitment: predatory and structural. The enlistment, intensity of indoctrination, types of training, and nature of deployment were found to depend, to a high degree, on the type of recruitment (i.e., predatory or structural, and category of children based on their origin (i.e., local, Middle Eastern and North African [MENA], or foreign and if they are orphans. The data shows that the separation between children and adults’ roles/assignments is diminishing. After a thorough exploration of the elements of ISIS’ recruitment and deployment process, this paper argues its findings, implications, and limitations.

High precision and stable structures for particle detectors

CERN Document Server

Da Mota Silva, S; Hauviller, Claude

1999-01-01

The central detectors used in High Energy Physics Experiments require the use of light and stable structures capable of supporting delicate and precise radiation detection elements. These structures need to be highly stable under environmental conditions where external vibrations, high radiation levels, temperature and humidity gradients should be taken into account. Their main design drivers are high dimension and dynamic stability, high stiffness to mass ratio and large radiation length. For most applications, these constraints lead us to choose Carbon Fiber Reinforced Plastics ( CFRP) as structural element. The construction of light and stable structures with CFRP for these applications can be achieved by careful design engineering and further confirmation at the prototyping phase. However, the experimental environment can influence their characteristics and behavior. In this case, theuse of adaptive structures could become a solution for this problem. We are studying structures in CFRP with bonded piezoel...

SpRoUTS (Space Robot Universal Truss System): Reversible Robotic Assembly of Deployable Truss Structures of Reconfigurable Length

Science.gov (United States)

Jenett, Benjamin; Cellucci, Daniel; Cheung, Kenneth

2015-01-01

Automatic deployment of structures has been a focus of much academic and industrial work on infrastructure applications and robotics in general. This paper presents a robotic truss assembler designed for space applications - the Space Robot Universal Truss System (SpRoUTS) - that reversibly assembles a truss from a feedstock of hinged andflat-packed components, by folding the sides of each component up and locking onto the assembled structure. We describe the design and implementation of the robot and show that the assembled truss compares favorably with prior truss deployment systems.

Fundamentals of 3D Deployable Mechanisms in Space

Data.gov (United States)

National Aeronautics and Space Administration — Fundamentals of 3D Deployable Origami Structures in Space The primary objectives of my research are to study the application of 3D deployable origami structures in...

Precision and Accuracy Parameters in Structured Light 3-D Scanning

Science.gov (United States)

Eiríksson, E. R.; Wilm, J.; Pedersen, D. B.; Aanæs, H.

2016-04-01

Structured light systems are popular in part because they can be constructed from off-the-shelf low cost components. In this paper we quantitatively show how common design parameters affect precision and accuracy in such systems, supplying a much needed guide for practitioners. Our quantitative measure is the established VDI/VDE 2634 (Part 2) guideline using precision made calibration artifacts. Experiments are performed on our own structured light setup, consisting of two cameras and a projector. We place our focus on the influence of calibration design parameters, the calibration procedure and encoding strategy and present our findings. Finally, we compare our setup to a state of the art metrology grade commercial scanner. Our results show that comparable, and in some cases better, results can be obtained using the parameter settings determined in this study.

Precision segmented reflectors for space applications

Science.gov (United States)

Lehman, David H.; Pawlik, Eugene V.; Meinel, Aden B.; Fichter, W. B.

1990-08-01

A project to develop precision segmented reflectors (PSRs) which operate at submillimeter wavelengths is described. The development of a light efficient means for the construction of large-aperture segmented reflecting space-based telescopes is the primary aim of the project. The 20-m Large Deployable Reflector (LDR) telescope is being developed for a survey mission, and it will make use of the reflector panels and materials, structures, and figure control being elaborated for the PSR. The surface accuracy of a 0.9-m PSR panel is shown to be 1.74-micron RMS, the goal of 100-micron RMS positioning accuracy has been achieved for a 4-m erectable structure. A voice-coil actuator for the figure control system architecture demonstrated 1-micron panel control accuracy in a 3-axis evaluation. The PSR technology is demonstrated to be of value for several NASA projects involving optical communications and interferometers as well as missions which make use of large-diameter segmented reflectors.

Do we see what we should see? Describing non-covalent interactions in protein structures including precision

Directory of Open Access Journals (Sweden)

Manickam Gurusaran

2014-01-01

Full Text Available The power of X-ray crystal structure analysis as a technique is to `see where the atoms are'. The results are extensively used by a wide variety of research communities. However, this `seeing where the atoms are' can give a false sense of security unless the precision of the placement of the atoms has been taken into account. Indeed, the presentation of bond distances and angles to a false precision (i.e. to too many decimal places is commonplace. This article has three themes. Firstly, a basis for a proper representation of protein crystal structure results is detailed and demonstrated with respect to analyses of Protein Data Bank entries. The basis for establishing the precision of placement of each atom in a protein crystal structure is non-trivial. Secondly, a knowledge base harnessing such a descriptor of precision is presented. It is applied here to the case of salt bridges, i.e. ion pairs, in protein structures; this is the most fundamental place to start with such structure-precision representations since salt bridges are one of the tenets of protein structure stability. Ion pairs also play a central role in protein oligomerization, molecular recognition of ligands and substrates, allosteric regulation, domain motion and α-helix capping. A new knowledge base, SBPS (Salt Bridges in Protein Structures, takes these structural precisions into account and is the first of its kind. The third theme of the article is to indicate natural extensions of the need for such a description of precision, such as those involving metalloproteins and the determination of the protonation states of ionizable amino acids. Overall, it is also noted that this work and these examples are also relevant to protein three-dimensional structure molecular graphics software.

Design aspects of a deployable tensegrity-hollow-rope footbridge

OpenAIRE

Rhode-Barbarigos , Landolf; Bel Hadj Ali , Nizar; Motro , René; Smith , Ian F.C.

2012-01-01

International audience; Tensegrity structures are composed of cables and struts in a pre-stressed self-equilibrium. Although tensegrity first appeared in the 1950s, it is seldom used in civil engineering. This paper focuses on the design aspects of a deployable tensegrity-hollow-rope footbridge. Deployment is usually not a critical design case for traditional deployable structures. However, for tensegrity systems deployment may be critical due to the actuation required. In this paper, deploym...

Concept-Development of a Structure Supported Membrane for Deployable Space Applications - From Nature to Manufacture and Testing

Science.gov (United States)

Zander, Martin; Belvin, W. K.

2012-01-01

Current space applications of membrane structures include large area solar power arrays, solar sails, antennas, and numerous other large aperture devices like the solar shades of the new James Webb Space Telescope. These expandable structural systems, deployed in-orbit to achieve the desired geometry, are used to collect, reflect and/or transmit electromagnetic radiation. This work, a feasibility study supporting a diploma thesis, describes the systematic process for developing a biologically inspired concept for a structure supported (integrated) membrane, that features a rip stop principle, makes self-deployment possible and is part of an ultra-light weight space application. Novel manufacturing of membrane prototypes and test results are presented for the rip-stop concepts. Test data showed that the new membrane concept has a higher tear resistance than neat film of equivalent mass.

Cryogenic Piezo Actuators for Lightweight, Large Aperture, Deployable Membrane Mirrors, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Single crystal piezoelectric actuators are proposed to enable large stroke, high precision, shape control for cryogenic lightweight deployable membrane mirror...

Precision mechanical structure of an ultra-high-resolution spectrometer for inelastic X-ray scattering instrument

Science.gov (United States)

Shu, Deming; Shvydko, Yuri; Stoupin, Stanislav A.; Khachatryan, Ruben; Goetze, Kurt A.; Roberts, Timothy

2015-04-14

A method and an ultrahigh-resolution spectrometer including a precision mechanical structure for positioning inelastic X-ray scattering optics are provided. The spectrometer includes an X-ray monochromator and an X-ray analyzer, each including X-ray optics of a collimating (C) crystal, a pair of dispersing (D) element crystals, anomalous transmission filter (F) and a wavelength (W) selector crystal. A respective precision mechanical structure is provided with the X-ray monochromator and the X-ray analyzer. The precision mechanical structure includes a base plate, such as an aluminum base plate; positioning stages for D-crystal alignment; positioning stages with an incline sensor for C/F/W-crystal alignment, and the positioning stages including flexure-based high-stiffness structure.

An introduction about precise measurements of QED γ structure functions

International Nuclear Information System (INIS)

Courau, A.

1989-11-01

Pure QED processes are theoretically exactly computable. However precise measurements and theoretical expectations of QED γ structure functions within a given experimental acceptance are not so trivial. Yet such a study is quite interesting. It supplies on the one hand a good QED test and, on the other hand, a good exercise for testing the procedure used for the determination of the hadronic γ structure functions

Development of distortion measurement system for large deployable antenna via photogrammetry in vacuum and cryogenic environment

Science.gov (United States)

Zhang, Pengsong; Jiang, Shanping; Yang, Linhua; Zhang, Bolun

2018-01-01

In order to meet the requirement of high precision thermal distortion measurement foraΦ4.2m deployable mesh antenna of satellite in vacuum and cryogenic environment, based on Digital Close-range Photogrammetry and Space Environment Test Technology of Spacecraft, a large scale antenna distortion measurement system under vacuum and cryogenic environment is developed in this paper. The antenna Distortion measurement system (ADMS) is the first domestic independently developed thermal distortion measurement system for large antenna, which has successfully solved non-contact high precision distortion measurement problem in large spacecraft structure under vacuum and cryogenic environment. The measurement accuracy of ADMS is better than 50 μm/5m, which has reached international advanced level. The experimental results show that the measurement system has great advantages in large structural measurement of spacecrafts, and also has broad application prospects in space or other related fields.

Analysis of intelligent hinged shell structures: deployable deformation and shape memory effect

Science.gov (United States)

Shi, Guang-Hui; Yang, Qing-Sheng; He, X. Q.

2013-12-01

Shape memory polymers (SMPs) are a class of intelligent materials with the ability to recover their initial shape from a temporarily fixable state when subjected to external stimuli. In this work, the thermo-mechanical behavior of a deployable SMP-based hinged structure is modeled by the finite element method using a 3D constitutive model with shape memory effect. The influences of hinge structure parameters on the nonlinear loading process are investigated. The total shape memory of the processes the hinged structure goes through, including loading at high temperature, decreasing temperature with load carrying, unloading at low temperature and recovering the initial shape with increasing temperature, are illustrated. Numerical results show that the present constitutive theory and the finite element method can effectively predict the complicated thermo-mechanical deformation behavior and shape memory effect of SMP-based hinged shell structures.

Analysis of intelligent hinged shell structures: deployable deformation and shape memory effect

International Nuclear Information System (INIS)

Shi, Guang-Hui; Yang, Qing-Sheng; He, X Q

2013-01-01

Shape memory polymers (SMPs) are a class of intelligent materials with the ability to recover their initial shape from a temporarily fixable state when subjected to external stimuli. In this work, the thermo-mechanical behavior of a deployable SMP-based hinged structure is modeled by the finite element method using a 3D constitutive model with shape memory effect. The influences of hinge structure parameters on the nonlinear loading process are investigated. The total shape memory of the processes the hinged structure goes through, including loading at high temperature, decreasing temperature with load carrying, unloading at low temperature and recovering the initial shape with increasing temperature, are illustrated. Numerical results show that the present constitutive theory and the finite element method can effectively predict the complicated thermo-mechanical deformation behavior and shape memory effect of SMP-based hinged shell structures. (paper)

Modelling and Analysis of the Folding Principle used in Selv-Deployable Deorbiting Space Structures

DEFF Research Database (Denmark)

Nikolajsen, Jan Ánike; Lauridsen, Peter Riddersholm; Kristensen, Anders Schmidt

2017-01-01

An initial prototype of the Self-deployable Deorbiting Space Structure (SDSS) for semi-controlled debris removal was launched in 2014. The SDSS module consists of 3 main systems, i.e. the Drag Sail Unit (DSU), the Release Unit (RU) and the Housing Unit (HU). In the redesign, a storage lid is intr...

Precision and Accuracy Parameters in Structured Light 3-D Scanning

DEFF Research Database (Denmark)

Eiríksson, Eyþór Rúnar; Wilm, Jakob; Pedersen, David Bue

2016-01-01

measure is the established VDI/VDE 2634 (Part 2) guideline using precision made calibration artifacts. Experiments are performed on our own structured light setup, consisting of two cameras and a projector. We place our focus on the influence of calibration design parameters, the calibration procedure...

Barriers and incentives of CCS deployment in China. Results from semi-structured interviews

International Nuclear Information System (INIS)

Dapeng, Liang; Weiwei, Wu

2009-01-01

From March to July of 2008, we conducted semi-structured interviews with 31 experts from the Chinese government, scientific institutes and industrial sectors. This paper summarizes the experts' opinions and draws conclusions about four crucial aspects that influence CO 2 capture and storage (CCS) deployment in China: technology research and experience accumulation, finance support, market development and policy and system. According to interviews result, technological improvement is necessary to cut down on CO 2 capture cost and decrease technological uncertainty. Then, to make some rational policies and systems, with elements such as a carbon tax and clean electricity pricing, to drive power plants to adopt CO 2 capture technology. Furthermore, financial incentive in both the long term and the short term, such as subsidies and CDM, will be important for CCS incentives, encouraging enterprises' enthusiasm for CCS and their capacity to enact it. Lastly, CCS deployment should be conducted under a market-oriented framework in the long term, so a business model and niche market deployment should be considered in advance. Among these aspects, policy and system is more complex than other three aspects, to resolve this obstacle, the innovation on electricity market and government decision model for climate change is crucial. (author)

Fine structures of atomic excited states: precision atomic spectroscopy and electron-ion collision process

International Nuclear Information System (INIS)

Gao Xiang; Cheng Cheng; Li Jiaming

2011-01-01

Scientific research fields for future energies such as inertial confinement fusion researches and astrophysics studies especially with satellite observatories advance into stages of precision physics. The relevant atomic data are not only enormous but also of accuracy according to requirements, especially for both energy levels and the collision data. The fine structure of high excited states of atoms and ions can be measured by precision spectroscopy. Such precision measurements can provide not only knowledge about detailed dynamics of electron-ion interactions but also a bench mark examination of the accuracy of electron-ion collision data, especially incorporating theoretical computations. We illustrate that by using theoretical calculation methods which can treat the bound states and the adjacent continua on equal footing. The precision spectroscopic measurements of excited fine structures can be served as stringent tests of electron-ion collision data. (authors)

Improving the precision of the structure-function relationship by considering phylogenetic context.

Directory of Open Access Journals (Sweden)

2005-06-01

Full Text Available Understanding the relationship between protein structure and function is one of the foremost challenges in post-genomic biology. Higher conservation of structure could, in principle, allow researchers to extend current limitations of annotation. However, despite significant research in the area, a precise and quantitative relationship between biochemical function and protein structure has been elusive. Attempts to draw an unambiguous link have often been complicated by pleiotropy, variable transcriptional control, and adaptations to genomic context, all of which adversely affect simple definitions of function. In this paper, I report that integrating genomic information can be used to clarify the link between protein structure and function. First, I present a novel measure of functional proximity between protein structures (F-score. Then, using F-score and other entirely automatic methods measuring structure and phylogenetic similarity, I present a three-dimensional landscape describing their inter-relationship. The result is a "well-shaped" landscape that demonstrates the added value of considering genomic context in inferring function from structural homology. A generalization of methodology presented in this paper can be used to improve the precision of annotation of genes in current and newly sequenced genomes.

Precision monitoring of bridge deck curvature change during replacement.

Science.gov (United States)

2016-05-01

This project was focused on development and deployment of a system for monitoring vertical : displacement in bridge decks and bridge spans. The system uses high precision wireless inclinometer : sensors to monitor inclinations at various points of a ...

Deployment of a pentagonal hollow-rope tensegrity module

OpenAIRE

Rhode-Barbarigos , Landolf; Bel Hadj Ali , Nizar; Motro , René; Smith , Ian F.C.

2011-01-01

International audience; Tensegrity structures are spatial reticulated structures composed of cables and struts. Tensegrity systems are good candidates for adaptive and deployable structures and thus have applications in various engineering fields. A "hollow-rope" tensegrity system composed of tensegrity-ring modules has been demonstrated by the authors to be a viable system for a pedestrian bridge. This paper focuses on the deployment of pentagonal ring modules. A geometric study is performed...

Precision manufacturing

CERN Document Server

Dornfeld, David

2008-01-01

Today there is a high demand for high-precision products. The manufacturing processes are now highly sophisticated and derive from a specialized genre called precision engineering. Precision Manufacturing provides an introduction to precision engineering and manufacturing with an emphasis on the design and performance of precision machines and machine tools, metrology, tooling elements, machine structures, sources of error, precision machining processes and precision process planning. As well as discussing the critical role precision machine design for manufacturing has had in technological developments over the last few hundred years. In addition, the influence of sustainable manufacturing requirements in precision processes is introduced. Drawing upon years of practical experience and using numerous examples and illustrative applications, David Dornfeld and Dae-Eun Lee cover precision manufacturing as it applies to: The importance of measurement and metrology in the context of Precision Manufacturing. Th...

Testing Starshade Manufacturing and Deployment Through NASA's Technology Development for Exoplanet Missions Program

Science.gov (United States)

Kasdin, N. J.; Shaklan, S.; Lisman, D.; Thomson, M.; Cady, E.; Lo, A.; Macintosh, B.

2014-01-01

An external occulter is a satellite employing a large screen, or starshade, that flies in formation with a spaceborne telescope to provide the starlight suppression needed for detecting and characterizing exoplanets. Among the advantages of using an occulter are the broadband allowed for characterization and the removal of light before entering the observatory, greatly relaxing the requirements on the telescope and instrument. In this poster we report on the results of our two Technology Development for Exoplanet Missions (TDEM) studies. In the first we examined the manufacturability and metrology of starshade petals, successfully constructing a full size petal from flight like materials and showing through precise edge shape measurements that an occulter made with petals consistent with the measured accuracy would achieve close to 10^-10 contrast. Our second TDEM tested the deployment precision of a roughly half-scale starshade. We demonstrated the deployment of an existing deployable truss outfitted with four sub-scale petals and a custom designed central hub. We showed that the system can be deployed multiple times with a repeatable positioning accuracy of the petals better than the requirement of 1.0 mm. The combined results of these two TDEM projects has significantly advanced the readiness level of occulter technology and moved the community closer to a realizable mission.

Deformation behavior of carbon-fiber reinforced shape-memory-polymer composites used for deployable structures (Conference Presentation)

Science.gov (United States)

Lan, Xin; Liu, Liwu; Li, Fengfeng; Pan, Chengtong; Liu, Yanju; Leng, Jinsong

2017-04-01

Shape memory polymers (SMPs) are a new type of smart material, they perform large reversible deformation with a certain external stimulus (e.g., heat and electricity). The properties (e.g., stiffness, strength and other mechanically static or quasi-static load-bearing capacity) are primarily considered for conventional resin-based composite materials which are mainly used for structural materials. By contrast, the mechanical actuating performance with finite deformation is considered for the shape memory polymers and their composites which can be used for both structural materials and functional materials. For shape memory polymers and their composites, the performance of active deformation is expected to further promote the development in smart active deformation structures, such as deployable space structures and morphing wing aircraft. The shape memory polymer composites (SMPCs) are also one type of High Strain Composite (HSC). The space deployable structures based on carbon fiber reinforced shape memory polymer composites (SMPCs) show great prospects. Considering the problems that SMPCs are difficult to meet the practical applications in space deployable structures in the recent ten years, this paper aims to research the mechanics of deformation, actuation and failure of SMPCs. In the overall view of the shape memory polymer material's nonlinearity (nonlinearity and stress softening in the process of pre-deformation and recovery, relaxation in storage process, irreversible deformation), by the multiple verifications among theory, finite element and experiments, one obtains the deformation and actuation mechanism for the process of "pre-deformation, energy storage and actuation" and its non-fracture constraint domain. Then, the parameters of SMPCs will be optimized. Theoretical analysis is realized by the strain energy function, additionally considering the interaction strain energy between the fiber and the matrix. For the common resin-based or soft

Advances in Text Mining and Visualization for Precision Medicine.

Science.gov (United States)

Gonzalez-Hernandez, Graciela; Sarker, Abeed; O'Connor, Karen; Greene, Casey; Liu, Hongfang

2018-01-01

According to the National Institutes of Health (NIH), precision medicine is "an emerging approach for disease treatment and prevention that takes into account individual variability in genes, environment, and lifestyle for each person." Although the text mining community has explored this realm for some years, the official endorsement and funding launched in 2015 with the Precision Medicine Initiative are beginning to bear fruit. This session sought to elicit participation of researchers with strong background in text mining and/or visualization who are actively collaborating with bench scientists and clinicians for the deployment of integrative approaches in precision medicine that could impact scientific discovery and advance the vision of precision medicine as a universal, accessible approach at the point of care.

An assessment of the precision and confidence of aquatic eddy correlation measurements

DEFF Research Database (Denmark)

Donis, Daphne; Holtappels, Moritz; Noss, Christian

2015-01-01

facility with well-constrained hydrodynamics. These observations are used to review data processing procedures and to recommend improved deployment methods, thus improving the precision, reliability, and confidence of EC measurements. Specifically, this study demonstrates that 1) the alignment of the time...... series based on maximum cross correlation improved the precision of EC flux estimations; 2) an oxygen sensor with a response time of

A discrete time-varying internal model-based approach for high precision tracking of a multi-axis servo gantry.

Science.gov (United States)

Zhang, Zhen; Yan, Peng; Jiang, Huan; Ye, Peiqing

2014-09-01

In this paper, we consider the discrete time-varying internal model-based control design for high precision tracking of complicated reference trajectories generated by time-varying systems. Based on a novel parallel time-varying internal model structure, asymptotic tracking conditions for the design of internal model units are developed, and a low order robust time-varying stabilizer is further synthesized. In a discrete time setting, the high precision tracking control architecture is deployed on a Voice Coil Motor (VCM) actuated servo gantry system, where numerical simulations and real time experimental results are provided, achieving the tracking errors around 3.5‰ for frequency-varying signals. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

Calibration procedure for Slocum glider deployed optical instruments.

Science.gov (United States)

Cetinić, Ivona; Toro-Farmer, Gerardo; Ragan, Matthew; Oberg, Carl; Jones, Burton H

2009-08-31

Recent developments in the field of the autonomous underwater vehicles allow the wide usage of these platforms as part of scientific experiments, monitoring campaigns and more. The vehicles are often equipped with sensors measuring temperature, conductivity, chlorophyll a fluorescence (Chl a), colored dissolved organic matter (CDOM) fluorescence, phycoerithrin (PE) fluorescence and spectral volume scattering function at 117 degrees, providing users with high resolution, real time data. However, calibration of these instruments can be problematic. Most in situ calibrations are performed by deploying complementary instrument packages or water samplers in the proximity of the glider. Laboratory calibrations of the mounted sensors are difficult due to the placement of the instruments within the body of the vehicle. For the laboratory calibrations of the Slocum glider instruments we developed a small calibration chamber where we can perform precise calibrations of the optical instruments aboard our glider, as well as sensors from other deployment platforms. These procedures enable us to obtain pre- and post-deployment calibrations for optical fluorescence instruments, which may differ due to the biofouling and other physical damage that can occur during long-term glider deployments. We found that biofouling caused significant changes in the calibration scaling factors of fluorescent sensors, suggesting the need for consistent and repetitive calibrations for gliders as proposed in this paper.

Effects of Long-Term Stowage on the Deployment of Bistable Tape Springs

OpenAIRE

Brinkmeyer, Alex; Pellegrino, Sergio; Weaver, Paul M.

2016-01-01

In the context of strain-energy-deployed space structures, material relaxation effects play a significant role in structures that are stowed for long durations, for example, in a space vehicle prior to launch. Here, the deployment of an ultrathin carbon fiber reinforced plastic (CFRP) tape spring is studied, with the aim of understanding how long-duration stowage affects its deployment behavior. Analytical modeling and experiments show that the deployment time increases predictably with stowa...

Hybrid deployable support truss designs for LDR

Science.gov (United States)

Hedgepeth, J.

1988-01-01

Concepts for a 20-meter diameter Large Deployable Reflector (LDR) deployable truss backup structure, and analytical predictions of its structural characteristics are discussed. The concept shown is referred to as the SIXPAC; It is a combination of the PACTRUSS concept and a single-fold beam, which would make up the desired backup structure. One advantage of retaining the PACTRUSS concept is its packaging density and its capability for synchronous deployment. Various 2-meter hexagonal panel arrangements are possible for this Hybrid PACTRUSS structure depending on the panel-to-structure attachment strategies used. Static analyses of the SIXPAC using various assumptions for truss designs and panel masses of 10 kg sq meters were performed to predict the tip displacement of the structure when supported at the center. The tip displacement ranged from 0.20 to 0.44 mm without the panel mass, and from 0.9 to 3.9 mm with the panel mass (in a 1-g field). The data indicate that the structure can be adequately ground tested to validate its required performance in space, assuming the required performance in space is approximately 100 microns. The static displacement at the tip of the structure when subjected to an angular acceleration of 0.001 rad/sec squared were estimated to range from 0.8 to 7.5 microns, depending on the type of truss elements.

Simulation and analysis of tape spring for deployed space structures

Science.gov (United States)

Chang, Wei; Cao, DongJing; Lian, MinLong

2018-03-01

The tape spring belongs to the configuration of ringent cylinder shell, and the mechanical properties of the structure are significantly affected by the change of geometrical parameters. There are few studies on the influence of geometrical parameters on the mechanical properties of the tape spring. The bending process of the single tape spring was simulated based on simulation software. The variations of critical moment, unfolding moment, and maximum strain energy in the bending process were investigated, and the effects of different radius angles of section and thickness and length on driving capability of the simple tape spring was studied by using these parameters. Results show that the driving capability and resisting disturbance capacity grow with the increase of radius angle of section in the bending process of the single tape spring. On the other hand, these capabilities decrease with increasing length of the single tape spring. In the end, the driving capability and resisting disturbance capacity grow with the increase of thickness in the bending process of the single tape spring. The research has a certain reference value for improving the kinematic accuracy and reliability of deployable structures.

Thermal shock induced dynamics of a spacecraft with a flexible deploying boom

Science.gov (United States)

Shen, Zhenxing; Li, Huijian; Liu, Xiaoning; Hu, Gengkai

2017-12-01

The dynamics in the process of deployment of a flexible extendible boom as a deployable structure on the spacecraft is studied. For determining the thermally induced vibrations of the boom subjected to an incident solar heat flux, an axially moving thermal-dynamic beam element based on the absolute nodal coordinate formulation which is able to precisely describe the large displacement, rotation and deformation of flexible body is presented. For the elastic forces formulation of variable-length beam element, the enhanced continuum mechanics approach is adopted, which can eliminate the Poisson locking effect, and take into account the tension-bending-torsion coupling deformations. The main body of the spacecraft, modeled as a rigid body, is described using the natural coordinates method. In the derived nonlinear thermal-dynamic equations of rigid-flexible multibody system, the mass matrix is time-variant, and a pseudo damping matrix which is without actual energy dissipation, and a heat conduction matrix which is relative to the moving speed and the number of beam element are arisen. Numerical results give the dynamic and thermal responses of the nonrotating and spinning spacecraft, respectively, and show that thermal shock has a significant influence on the dynamics of spacecraft.

Precise Measurement of the Deuteron Elastic structure Function A(Q2)

International Nuclear Information System (INIS)

D. Abbott; A. Ahmidouch; H. Anklin; J. Arvieux; J. Bail; S. Beedoe; E. J. Beise; L. Bimbot; W. Boeglin; H. Breuer; R. Carlini; N. S. Chant; S. Danagoulian; K. Dow; J.E. Ducret; J. Dunne; R. Ent; L. Ewell; L. Eyraud; C. Furget; M. Garcon; R. Gilman; C. Glashausser; P. Gucye; K. Gustafsson; K. Hafidi; A. Honegger; J. Jourdan; S. Kox; G. Kumbartzki; L. Lu; A. Lung; D. Mack; P. Markowitz; J. McIntyre; D. Meekins; F. Merchez; J. Mitchell; R. Mohring; S. Mtingwa; H. Mrktchyan; D. Pitz; L. Qin; R. Ransome; J.S. Real; P. G. Roos; P. Rutt; R. Sawafta; S. Stepanyan; R. Tieulent; E. Tomasi-Gustafsson; W. Turchinetz; K. Vansyoc; J. Volmer; E. Voutier; W. Vulcan; C. Williamson; S. A. Wood; C. Yan; J. Zhao; W. Zhao

1999-01-01

The A(Q 2 ) structure function in elastic electron-deuteron scattering was measured at six momentum transfers Q 2 between 0.66 and 1.80 (GeV/c) 2 in Hall C at Jefferson Laboratory. The scattered electrons and recoil deuterons were detected in coincidence, at a fixed deuteron angle of 60.5 o . These new precise measurements resolve discrepancies between older sets of data. They put significant constraints on existing models of the deuteron electromagnetic structure, and on the strength of isoscalar meson exchange currents

Advanced Smart Structures Flight Experiments for Precision Spacecraft

Science.gov (United States)

Denoyer, Keith K.; Erwin, R. Scott; Ninneman, R. Rory

2000-07-01

This paper presents an overview as well as data from four smart structures flight experiments directed by the U.S. Air Force Research Laboratory's Space Vehicles Directorate in Albuquerque, New Mexico. The Middeck Active Control Experiment $¯Flight II (MACE II) is a space shuttle flight experiment designed to investigate modeling and control issues for achieving high precision pointing and vibration control of future spacecraft. The Advanced Controls Technology Experiment (ACTEX-I) is an experiment that has demonstrated active vibration suppression using smart composite structures with embedded piezoelectric sensors and actuators. The Satellite Ultraquiet Isolation Technology Experiment (SUITE) is an isolation platform that uses active piezoelectric actuators as well as damped mechanical flexures to achieve hybrid passive/active isolation. The Vibration Isolation, Suppression, and Steering Experiment (VISS) is another isolation platform that uses viscous dampers in conjunction with electromagnetic voice coil actuators to achieve isolation as well as a steering capability for an infra-red telescope.

High Precision Thermal, Structural and Optical Analysis of an External Occulter Using a Common Model and the General Purpose Multi-Physics Analysis Tool Cielo

Science.gov (United States)

Hoff, Claus; Cady, Eric; Chainyk, Mike; Kissil, Andrew; Levine, Marie; Moore, Greg

2011-01-01

The efficient simulation of multidisciplinary thermo-opto-mechanical effects in precision deployable systems has for years been limited by numerical toolsets that do not necessarily share the same finite element basis, level of mesh discretization, data formats, or compute platforms. Cielo, a general purpose integrated modeling tool funded by the Jet Propulsion Laboratory and the Exoplanet Exploration Program, addresses shortcomings in the current state of the art via features that enable the use of a single, common model for thermal, structural and optical aberration analysis, producing results of greater accuracy, without the need for results interpolation or mapping. This paper will highlight some of these advances, and will demonstrate them within the context of detailed external occulter analyses, focusing on in-plane deformations of the petal edges for both steady-state and transient conditions, with subsequent optical performance metrics including intensity distributions at the pupil and image plane.

Very Low Head Turbine Deployment in Canada

International Nuclear Information System (INIS)

Kemp, P; Williams, C; Sasseville, Remi; Anderson, N

2014-01-01

The Very Low Head (VLH) turbine is a recent turbine technology developed in Europe for low head sites in the 1.4 - 4.2 m range. The VLH turbine is primarily targeted for installation at existing hydraulic structures to provide a low impact, low cost, yet highly efficient solution. Over 35 VLH turbines have been successfully installed in Europe and the first VLH deployment for North America is underway at Wasdell Falls in Ontario, Canada. Deployment opportunities abound in Canada with an estimated 80,000 existing structures within North America for possible low-head hydro development. There are several new considerations and challenges for the deployment of the VLH turbine technology in Canada in adapting to the hydraulic, environmental, electrical and social requirements. Several studies were completed to determine suitable approaches and design modifications to mitigate risk and confirm turbine performance. Diverse types of existing weirs and spillways pose certain hydraulic design challenges. Physical and numerical modelling of the VLH deployment alternatives provided for performance optimization. For this application, studies characterizing the influence of upstream obstacles using water tunnel model testing as well as full-scale prototype flow dynamics testing were completed. A Cold Climate Adaptation Package (CCA) was developed to allow year-round turbine operation in ice covered rivers. The CCA package facilitates turbine extraction and accommodates ice forces, frazil ice, ad-freezing and cold temperatures that are not present at the European sites. The Permanent Magnet Generator (PMG) presents some unique challenges in meeting Canadian utility interconnection requirements. Specific attention to the frequency driver control and protection requirements resulted in a driver design with greater over-voltage capability for the PMG as well as other key attributes. Environmental studies in Europe included fish friendliness testing comprised of multiple in

Very Low Head Turbine Deployment in Canada

Science.gov (United States)

Kemp, P.; Williams, C.; Sasseville, Remi; Anderson, N.

2014-03-01

The Very Low Head (VLH) turbine is a recent turbine technology developed in Europe for low head sites in the 1.4 - 4.2 m range. The VLH turbine is primarily targeted for installation at existing hydraulic structures to provide a low impact, low cost, yet highly efficient solution. Over 35 VLH turbines have been successfully installed in Europe and the first VLH deployment for North America is underway at Wasdell Falls in Ontario, Canada. Deployment opportunities abound in Canada with an estimated 80,000 existing structures within North America for possible low-head hydro development. There are several new considerations and challenges for the deployment of the VLH turbine technology in Canada in adapting to the hydraulic, environmental, electrical and social requirements. Several studies were completed to determine suitable approaches and design modifications to mitigate risk and confirm turbine performance. Diverse types of existing weirs and spillways pose certain hydraulic design challenges. Physical and numerical modelling of the VLH deployment alternatives provided for performance optimization. For this application, studies characterizing the influence of upstream obstacles using water tunnel model testing as well as full-scale prototype flow dynamics testing were completed. A Cold Climate Adaptation Package (CCA) was developed to allow year-round turbine operation in ice covered rivers. The CCA package facilitates turbine extraction and accommodates ice forces, frazil ice, ad-freezing and cold temperatures that are not present at the European sites. The Permanent Magnet Generator (PMG) presents some unique challenges in meeting Canadian utility interconnection requirements. Specific attention to the frequency driver control and protection requirements resulted in a driver design with greater over-voltage capability for the PMG as well as other key attributes. Environmental studies in Europe included fish friendliness testing comprised of multiple in

Quality function deployment

International Nuclear Information System (INIS)

1981-10-01

This book indicates quality function deployment with quality and deployment of quality function, process and prospect of quality function deployment and development, product process and conception of quality table, deployment of quality demand, design of quality table and application of concurrent multi design, progress design and quality development, main safe part and management of important function part, quality development and deployment of method of construction, quality deployment and economics, total system of quality function deployment and task of quality function deployment in the present and future.

Precise Measurement of the Deuteron Elastic Structure Function A(Q2 )

International Nuclear Information System (INIS)

Ball, J.; Ducret, J.; Garcon, M.; Hafidi, K.; Pitz, D.; Tomasi-Gustafsson, E.; Honegger, A.; Jourdan, J.; Zhao, J.; Beise, E.J.; Breuer, H.; Chant, N.S.; Ewell, L.; Gustafsson, K.; Lung, A.; Mohring, R.; Pitz, D.; Roos, P.G.; Eyraud, L.; Furget, C.; Kox, S.; Lu, L.; Merchez, F.; Real, J.; Tieulent, R.; Voutier, E.; Abbott, D.; Carlini, R.; Dunne, J.; Ent, R.; Gilman, R.; Gueye, P.; Mack, D.; Meekins, D.; Mitchell, J.; Pitz, D.; Qin, L.; Vansyoc, K.; Volmer, J.; Vulcan, W.; Wood, S.A.; Yan, C.; Gilman, R.; Glashausser, C.; Kumbartzki, G.; McIntyre, J.; Ransome, R.; Rutt, P.; Ahmidouch, A.; Dow, K.; Turchinetz, W.; Williamson, C.; Zhao, W.; Anklin, H.; Boeglin, W.; Markowitz, P.; Mrktchyan, H.; Stepanyan, S.; Ahmidouch, A.; Beedoe, S.; Danagoulian, S.; Mtingwa, S.; Sawafta, R.; Arvieux, J.; Ball, J.; Tomasi-Gustafsson, E.; Arvieux, J.; Bimbot, L.

1999-01-01

The A(Q 2 ) structure function in elastic electron-deuteron scattering was measured at six momentum transfers Q 2 between 0.66 and 1.80 (GeV/c) 2 in Hall C at Jefferson Laboratory. The scattered electrons and recoil deuterons were detected in coincidence, at a fixed deuteron angle of 60.5 degree. These new precise measurements resolve discrepancies between older sets of data. They put significant constraints on existing models of the deuteron electromagnetic structure, and on the strength of isoscalar meson exchange currents. copyright 1999 The American Physical Society

Self-Deploying, Composite Habitats, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Cornerstone Research Group, Inc. (CRG), proposes to develop self-deploying, composite structures for lunar habitats, based on CRG's VeritexTM materials. These...

Rover deployment system for lunar landing mission

Science.gov (United States)

Sutoh, Masataku; Hoshino, Takeshi; Wakabayashi, Sachiko

2017-09-01

For lunar surface exploration, a deployment system is necessary to allow a rover to leave the lander. The system should be as lightweight as possible and stored retracted when launched. In this paper, two types of retractable deployment systems for lunar landing missions, telescopic- and fold-type ramps, are discussed. In the telescopic-type system, a ramp is stored with the sections overlapping and slides out during deployment. In the fold-type system, it is stored folded and unfolds for the deployment. For the development of these ramps, a design concept study and structural analysis were conducted first. Subsequently, ramp deployment and rover release tests were performed using the developed ramp prototypes. Through these tests, the validity of their design concepts and functions have been confirmed. In the rover release test, it was observed that the developed lightweight ramp was sufficiently strong for a 50-kg rover to descend. This result suggests that this ramp system is suitable for the deployment of a 300-kg-class rover on the Moon, where the gravity is about one-sixth that on Earth. The lightweight and sturdy ramp developed in this study will contribute to both safe rover deployment and increase of lander/rover payload.

The structure of the proton in the LHC precision era

Science.gov (United States)

Gao, Jun; Harland-Lang, Lucian; Rojo, Juan

2018-05-01

We review recent progress in the determination of the parton distribution functions (PDFs) of the proton, with emphasis on the applications for precision phenomenology at the Large Hadron Collider (LHC). First of all, we introduce the general theoretical framework underlying the global QCD analysis of the quark and gluon internal structure of protons. We then present a detailed overview of the hard-scattering measurements, and the corresponding theory predictions, that are used in state-of-the-art PDF fits. We emphasize here the role that higher-order QCD and electroweak corrections play in the description of recent high-precision collider data. We present the methodology used to extract PDFs in global analyses, including the PDF parametrization strategy and the definition and propagation of PDF uncertainties. Then we review and compare the most recent releases from the various PDF fitting collaborations, highlighting their differences and similarities. We discuss the role that QED corrections and photon-initiated contributions play in modern PDF analysis. We provide representative examples of the implications of PDF fits for high-precision LHC phenomenological applications, such as Higgs coupling measurements and searches for high-mass New Physics resonances. We conclude this report by discussing some selected topics relevant for the future of PDF determinations, including the treatment of theoretical uncertainties, the connection with lattice QCD calculations, and the role of PDFs at future high-energy colliders beyond the LHC.

Deployment Testing of Flexible Composite Hinges in Bi-Material Beams

Science.gov (United States)

Sauder, Jonathan F.; Trease, Brian

2016-01-01

Composites have excellent properties for strength, thermal stability, and weight. However, they are traditionally highly rigid, and when used in deployable structures require hinges bonded to the composite material, which increases complexity and opportunities for failure. Recent research in composites has found by adding an elastomeric soft matrix, often silicone instead of an epoxy, the composite becomes flexible. This work explores the deployment repeatability of silicone matrix composite hinges which join rigid composite beams. The hinges were found to have sub-millimeter linear deployment repeatability, and sub-degree angular deployment repeatability. Also, an interesting relaxation effect was discovered, as a hinges deployment error would decrease with time.

Shape memory alloy fracture as a deployment actuator

International Nuclear Information System (INIS)

Buban, Darrick M; Frantziskonis, George N

2013-01-01

The paper reports an experimental investigation into using shape memory alloy (SMA) as a deployment actuator. SMA specimens were heated and pulled to failure or pulled and heated to failure, thus developing an environmental and structural operating envelope for application as deployment mechanisms. The experimental results strongly suggest that SMAs can be implemented as deployment actuators. Recorded data shows that SMA fracture is possible over a wide range of temperatures and strains, filling a material performance gap not found in the literature. The obtained information allows design engineers to appropriately size SMAs given the design requirements for achieving the desired deployment effects. The major conclusion of the reported work is that SMAs as actuators are strong competitors to typical existing deployment efforts that use explosive or non-explosive actuators having implementation drawbacks such as the expense associated with special handling and the volume encountered in mounting the devices. (paper)

New precise measurement of muonium hyperfine structure interval at J-PARC

Energy Technology Data Exchange (ETDEWEB)

Ueno, Y., E-mail: yueno@radphys4.c.u-tokyo.ac.jp [University of Tokyo, Graduate School of Arts and Sciences (Japan); Aoki, M. [Osaka University, Graduate School of Science (Japan); Fukao, Y. [KEK (Japan); Higashi, Y.; Higuchi, T. [University of Tokyo, Graduate School of Arts and Sciences (Japan); Iinuma, H.; Ikedo, Y. [KEK (Japan); Ishida, K. [RIKEN (Japan); Ito, T. U. [Japan Atomic Energy Agency (Japan); Iwasaki, M. [RIKEN (Japan); Kadono, R. [KEK (Japan); Kamigaito, O. [RIKEN (Japan); Kanda, S. [University of Tokyo, Department of Physics (Japan); Kawall, D. [University of Massachusetts, Amherst, Department of Physics (United States); Kawamura, N.; Koda, A.; Kojima, K. M. [KEK (Japan); Kubo, M. K. [International Christian University, Graduate School of Arts and Science (Japan); Matsuda, Y. [University of Tokyo, Graduate School of Arts and Sciences (Japan); Mibe, T. [KEK (Japan); and others

2017-11-15

MuSEUM is an international collaboration aiming at a new precise measurement of the muonium hyperfine structure at J-PARC (Japan Proton Accelerator Research Complex). Utilizing its intense pulsed muon beam, we expect a ten-fold improvement for both measurements at high magnetic field and zero magnetic field. We have developed a sophisticated monitoring system, including a beam profile monitor to measure the 3D distribution of muonium atoms to suppress the systematic uncertainty.

Application and testing of additive manufacturing for mirrors and precision structures

Science.gov (United States)

Sweeney, Michael; Acreman, Martyn; Vettese, Tom; Myatt, Ray; Thompson, Mike

2015-09-01

Additive Manufacturing (aka AM, and 3-D printing) is widely touted in the media as the foundation for the next industrial revolution. Beneath the hype, AM does indeed offer profound advantages in lead-time, dramatically reduced consumption of expensive raw materials, while enabling new and innovative design forms that cannot be produced by other means. General Dynamics and their industry partners have begun to embrace this technology for mirrors and precision structures used in the aerospace, defense, and precision optical instrumentation industries. Aggressively lightweighted, open and closed back test mirror designs, 75-150 mm in size, were first produced by AM from several different materials. Subsequent optical finishing and test experiments have exceeded expectations for density, surface finish, dimensional stability and isotropy of thermal expansion on the optical scale of measurement. Materials currently under examination include aluminum, titanium, beryllium, aluminum beryllium, Inconel 625, stainless steel/bronze, and PEKK polymer.

Accounting for variation in wind deployment between Canadian provinces

International Nuclear Information System (INIS)

Ferguson-Martin, Christopher J.; Hill, Stephen D.

2011-01-01

Wind energy deployment varies widely across regions and this variation cannot be explained by differences in natural wind resources alone. Evidence suggests that institutional factors beyond physical wind resources can influence the deployment of wind energy systems. Building on the work of , this study takes a historical institutionalist approach to examine the main factors influencing wind energy deployment across four Canadian provinces Canada: Alberta, Manitoba, Ontario and Nova Scotia. Our case studies suggest that wind energy deployment depends upon a combination of indirect causal factors-landscape values, political and social movements, government electricity policy, provincial electricity market structure and incumbent generation technologies and direct causal factors-grid architecture, ownership patterns, renewable incentive programs, planning and approvals processes and stakeholder support and opposition. - Research highlights: → Examines the reasons for variations in wind deployment between Canadian provinces. → Employs a historical institutional approach to the analysis. → Discusses social factors that affect wind deployment across Canadian jurisdictions.

A compact ultra-clean system for deploying radioactive sources inside the KamLAND detector

NARCIS (Netherlands)

Banks, T.I.; Freedman, S.J.; Wallig, J.; Ybarrolaza, N.; Gando, A.; Gando, Y.; Ikeda, H.; Inoue, K.; Kishimoto, Y.; Koga, M.; Mitsui, T.; Nakamura, K.; Shimizu, I.; Shirai, J.; Suzuki, A.; Takemoto, Y.; Tamae, K.; Ueshima, K.; Watanabe, H.; Xu, B.D.; Yoshida, H.; Yoshida, S.; Kozlov, A.; Grant, C.; Keefer, G.; Piepke, A.; Bloxham, T.; Fujikawa, B.K.; Han, K.; Ichimura, K.; Murayama, H.; O'Donnell, T.; Steiner, H.M.; Winslow, L.A.; Dwyer, D.A.; McKeown, R.D.; Zhang, C.; Berger, B.E.; Lane, C.E.; Maricic, J.; Miletic, T.; Batygov, M.; Learned, J.G.; Matsuno, S.; Sakai, M.; Horton-Smith, G.A.; Downum, K.E.; Gratta, G.; Efremenko, Y.; Perevozchikov, O.; Karwowski, H.J.; Markoff, D.M.; Tornow, W.; Heeger, K.M.; Detwiler, J.A.; Enomoto, S.; Decowski, M.P.

2015-01-01

We describe a compact, ultra-clean device used to deploy radioactive sources along the vertical axis of the KamLAND liquid-scintillator neutrino detector for purposes of calibration. The device worked by paying out and reeling in precise lengths of a hanging, small-gauge wire rope (cable); an

Cortical Coupling Reflects Bayesian Belief Updating in the Deployment of Spatial Attention.

Science.gov (United States)

Vossel, Simone; Mathys, Christoph; Stephan, Klaas E; Friston, Karl J

2015-08-19

The deployment of visuospatial attention and the programming of saccades are governed by the inferred likelihood of events. In the present study, we combined computational modeling of psychophysical data with fMRI to characterize the computational and neural mechanisms underlying this flexible attentional control. Sixteen healthy human subjects performed a modified version of Posner's location-cueing paradigm in which the percentage of cue validity varied in time and the targets required saccadic responses. Trialwise estimates of the certainty (precision) of the prediction that the target would appear at the cued location were derived from a hierarchical Bayesian model fitted to individual trialwise saccadic response speeds. Trial-specific model parameters then entered analyses of fMRI data as parametric regressors. Moreover, dynamic causal modeling (DCM) was performed to identify the most likely functional architecture of the attentional reorienting network and its modulation by (Bayes-optimal) precision-dependent attention. While the frontal eye fields (FEFs), intraparietal sulcus, and temporoparietal junction (TPJ) of both hemispheres showed higher activity on invalid relative to valid trials, reorienting responses in right FEF, TPJ, and the putamen were significantly modulated by precision-dependent attention. Our DCM results suggested that the precision of predictability underlies the attentional modulation of the coupling of TPJ with FEF and the putamen. Our results shed new light on the computational architecture and neuronal network dynamics underlying the context-sensitive deployment of visuospatial attention. Spatial attention and its neural correlates in the human brain have been studied extensively with the help of fMRI and cueing paradigms in which the location of targets is pre-cued on a trial-by-trial basis. One aspect that has so far been neglected concerns the question of how the brain forms attentional expectancies when no a priori probability

High-Performance Elastically Self-Deployed Roll-Out Solar Array (ROSA), Phase II

Data.gov (United States)

National Aeronautics and Space Administration — Deployable Space Systems (DSS) has developed an ultra-lightweight elastically self-deployable roll-out solar array (ROSA) structural platform that when combined with...

Correlation Processing Of Local Seismic Data: Applications for Autonomous Sensor Deployments

Energy Technology Data Exchange (ETDEWEB)

Dodge, D A

2010-11-16

Excavation and operation of an underground facility is likely to produce an extensive suite of seismic signals observable at the surface for perhaps several km. Probably a large fraction of such signals will be correlated, so the design of a monitoring framework should include consideration of a correlation processing capability. Correlation detectors have been shown to be significantly more sensitive than beam-forming power detectors. Although correlation detectors have a limited detection footprint, they can be generalized into multi-rank subspace detectors which are sensitive over a much larger range of source mechanisms and positions. Production of subspace detectors can be automated, so their use in an autonomous framework may be contemplated. Waveform correlation also can be used to produce very high precision phase picks which may be jointly inverted to simultaneously relocate groups of events. The relative precision of the resulting hypocenters is sufficient to visualize structural detail at a scale of less than a few tens of meters. Three possible correlation processor systems are presented. All use a subspace signal detection framework. The simplest system uses a single-component sensor and is capable of detection and classification of signals. The most complicated system uses many sensors deployed around the facility, and is capable of detection, classification, and high-precision source location. Data from a deep underground mine are presented to demonstrate the applicability of correlation processing to monitoring an underground facility. Although the source region covers an area of about 600m by 580m, all but two of the events form clusters at a threshold of 0.7. All the events could have been detected and classified by the subspace detection framework, and high-precision picks can be computed for all cluster members.

Technological developments for ultra-lightweight, large aperture, deployable mirror for space telescopes

Science.gov (United States)

Zuccaro Marchi, Alessandro; D'Amato, Francesco; Gallieni, Daniele; Biasi, Roberto; Molina, Marco; Duò, Fabrizio; Ruder, Nikolaus; Salinari, Piero; Lisi, Franco; Riccardi, Armando; Gambicorti, Lisa; Simonetti, Francesca; Pereira do Carmo, Joao Pedro N.

2017-11-01

The increasing interest on space telescopes for scientific applications leads to implement the manufacturing technology of the most critical element, i.e. the primary mirror: being more suitable a large aperture, it must be lightweight and deployable. The presented topic was originally addressed to a spaceborne DIAL (Differential Absorption LIDAR) mission operating at 935.5 nm for the measurement of water vapour profile in atmosphere, whose results were presented at ICSO 2006 and 2008. Aim of this paper is to present the latest developments on the main issues related to the fabrication of a breadboard, covering two project critical areas identified during the preliminary studies: the design and performances of the long-stroke actuators used to implement the mirror active control and the mirror survivability to launch via Electrostatic Locking (EL) between mirror and backplane. The described work is developed under the ESA/ESTEC contract No. 22321/09/NL/RA. The lightweight mirror is structured as a central sector surrounded by petals, all of them actively controlled to reach the specified shape after initial deployment and then maintained within specs for the entire mission duration. The presented study concerns: a) testing the Carbon Fiber Reinforced Plastic (CFRP) backplane manufacturing and EL techniques, with production of suitable specimens; b) actuator design optimisation; c) design of the deployment mechanism including a high precision latch; d) the fabrication of thin mirrors mock-ups to validate the fabrication procedure for the large shells. The current activity aims to the construction of an optical breadboard capable of demonstrating the achievement of all these coupled critical aspects: optical quality of the thin shell mirror surface, actuators performances and back-plane - EL subsystem functionality.

Origami-inspired, on-demand deployable and collapsible mechanical metamaterials with tunable stiffness

Science.gov (United States)

Zhai, Zirui; Wang, Yong; Jiang, Hanqing

2018-03-01

Origami has been employed to build deployable mechanical metamaterials through folding and unfolding along the crease lines. Deployable metamaterials are usually flexible, particularly along their deploying and collapsing directions, which unfortunately in many cases leads to an unstable deployed state, i.e., small perturbations may collapse the structure along the same deployment path. Here we create an origami-inspired mechanical metamaterial with on-demand deployability and selective collapsibility through energy analysis. This metamaterial has autonomous deployability from the collapsed state and can be selectively collapsed along two different paths, embodying low stiffness for one path and substantially high stiffness for another path. The created mechanical metamaterial yields load-bearing capability in the deployed direction while possessing great deployability and collapsibility. The principle in this work can be utilized to design and create versatile origami-inspired mechanical metamaterials that can find many applications.

A Precision Measurement of the Spin Structure Function G(2)(P)

Energy Technology Data Exchange (ETDEWEB)

Benmouna, N

2004-01-05

The spin structure function g{sub 2}(x,Q{sup 2}) and the virtual photon asymmetry A{sub 2}(x,Q{sup 2}) were measured for the proton using deep inelastic scattering. The experiment was conducted at the Stanford Linear Accelerator Center (SLAC), where longitudinally polarized electrons at 29.1 and 32.3 GeV were scattered from a transversely polarized NH{sub 3} target. Large data sets were accumulated using three independent spectrometers covering a kinematic range 0.02 {le} x {le} 0.8 and 1 {le} Q{sup 2} {le} 20 (GeV/c){sup 2}. This new data is the first data precise enough to distinguish between current models for the proton. The structure function g{sub 2}{sup p} was found to be reasonably consistent with the twist-2 Wandzura-Wilczek calculation. The Q{sup 2} dependence of g{sub 2} approximately follows the Q{sup 2} dependence of g{sub 2}{sup WW}, although the data are not precise enough to rule out no Q{sup 2} dependence. The absolute value for A{sub 2}{sup p} was found to be significantly smaller than the Soffer limit over the measured range. The virtual photon asymmetry A{sub 2} was also found to be inconsistent with zero over much of the measured range.

A hybrid fuzzy MCDM approach to maintenance Quality Function Deployment

Directory of Open Access Journals (Sweden)

Davy George Valavi

2015-01-01

Full Text Available Maintenance Quality Function Deployment (MQFD is a model, which enhances the synergic power of Quality Function Deployment (QFD and Total Productive Maintenance (TPM. One of the crucial and important steps during the implementation of MQFD is the determination of the importance or weightages of the critical factors (CF and sub factors (SF. The CFs and SFs have to be compared precisely for the successful implementation of MQFD. The crisp pair-wise comparison in the conventional Analytical Hierarchy Process (AHP may be insufficient to determine the degree of weightage of CFs and SFs where vagueness and uncetainties are associated. In this paper, a modification of AHP based MQFD by incorporating fuzzy operations is proposed, which can improve the accuracy of determination of the weightages. A case study showing the applicability of this method is illustrated in this paper.

A Nonlinear Dynamic Model and Free Vibration Analysis of Deployable Mesh Reflectors

Science.gov (United States)

Shi, H.; Yang, B.; Thomson, M.; Fang, H.

2011-01-01

This paper presents a dynamic model of deployable mesh reflectors, in which geometric and material nonlinearities of such a space structure are fully described. Then, by linearization around an equilibrium configuration of the reflector structure, a linearized model is obtained. With this linearized model, the natural frequencies and mode shapes of a reflector can be computed. The nonlinear dynamic model of deployable mesh reflectors is verified by using commercial finite element software in numerical simulation. As shall be seen, the proposed nonlinear model is useful for shape (surface) control of deployable mesh reflectors under thermal loads.

'Post-deployment appraisal' and the relationship with stress and psychological health in Australian veterans.

Science.gov (United States)

Wright, Breanna; Forbes, Andrew; Kelsall, Helen; Clarke, David; Ikin, Jill; Sim, Malcolm

2015-12-01

Understanding how veterans appraise their post-deployment experiences could provide insight into better assisting their deployment transitions. We aimed to assess the factor structure of positive and negative post-deployment appraisals in Australian veterans and to examine the resultant factors in their relationship with military stress and psychological health. Questions capturing post-deployment attitudes were developed by the researchers in collaboration with veterans. The questions were administered to 1938 veterans and the results factor analysed. The relationships between post-deployment appraisal, military stress and psychological health were examined using Structural Equation Modelling. A three-factor solution was found for the post-deployment appraisal questions; representing personal development, lack of recognition, and appreciation of life and country. Military stress was associated with the three factors and psychological health. The three factors were weakly to moderately associated with psychological health. Mediation between military stress and psychological health by any post-deployment appraisal factor was minimal. Post-deployment appraisal measures three important attitudes and concerns of veterans after deployment. Military stress is associated with the post-deployment appraisal factors. However, the factors did not mediate the relationship between military stress and psychological health. These factors provide insight into how veterans appraise their complex array of post-deployment experiences, and may provide useful in regard to transitions and integration into civilian life.

Study on the three-station typical network deployments of workspace Measurement and Positioning System

Science.gov (United States)

Xiong, Zhi; Zhu, J. G.; Xue, B.; Ye, Sh. H.; Xiong, Y.

2013-10-01

As a novel network coordinate measurement system based on multi-directional positioning, workspace Measurement and Positioning System (wMPS) has outstanding advantages of good parallelism, wide measurement range and high measurement accuracy, which makes it to be the research hotspots and important development direction in the field of large-scale measurement. Since station deployment has a significant impact on the measurement range and accuracy, and also restricts the use-cost, the optimization method of station deployment was researched in this paper. Firstly, positioning error model was established. Then focusing on the small network consisted of three stations, the typical deployments and error distribution characteristics were studied. Finally, through measuring the simulated fuselage using typical deployments at the industrial spot and comparing the results with Laser Tracker, some conclusions are obtained. The comparison results show that under existing prototype conditions, I_3 typical deployment of which three stations are distributed in a straight line has an average error of 0.30 mm and the maximum error is 0.50 mm in the range of 12 m. Meanwhile, C_3 typical deployment of which three stations are uniformly distributed in the half-circumference of an circle has an average error of 0.17 mm and the maximum error is 0.28 mm. Obviously, C_3 typical deployment has a higher control effect on precision than I_3 type. The research work provides effective theoretical support for global measurement network optimization in the future work.

On Efficient Deployment of Wireless Sensors for Coverage and Connectivity in Constrained 3D Space.

Science.gov (United States)

Wu, Chase Q; Wang, Li

2017-10-10

Sensor networks have been used in a rapidly increasing number of applications in many fields. This work generalizes a sensor deployment problem to place a minimum set of wireless sensors at candidate locations in constrained 3D space to k -cover a given set of target objects. By exhausting the combinations of discreteness/continuousness constraints on either sensor locations or target objects, we formulate four classes of sensor deployment problems in 3D space: deploy sensors at Discrete/Continuous Locations (D/CL) to cover Discrete/Continuous Targets (D/CT). We begin with the design of an approximate algorithm for DLDT and then reduce DLCT, CLDT, and CLCT to DLDT by discretizing continuous sensor locations or target objects into a set of divisions without sacrificing sensing precision. Furthermore, we consider a connected version of each problem where the deployed sensors must form a connected network, and design an approximation algorithm to minimize the number of deployed sensors with connectivity guarantee. For performance comparison, we design and implement an optimal solution and a genetic algorithm (GA)-based approach. Extensive simulation results show that the proposed deployment algorithms consistently outperform the GA-based heuristic and achieve a close-to-optimal performance in small-scale problem instances and a significantly superior overall performance than the theoretical upper bound.

Precision surveying the principles and geomatics practice

CERN Document Server

Ogundare, John Olusegun

2016-01-01

A comprehensive overview of high precision surveying, including recent developments in geomatics and their applications This book covers advanced precision surveying techniques, their proper use in engineering and geoscience projects, and their importance in the detailed analysis and evaluation of surveying projects. The early chapters review the fundamentals of precision surveying: the types of surveys; survey observations; standards and specifications; and accuracy assessments for angle, distance and position difference measurement systems. The book also covers network design and 3-D coordinating systems before discussing specialized topics such as structural and ground deformation monitoring techniques and analysis, mining surveys, tunneling surveys, and alignment surveys. Precision Surveying: The Principles and Geomatics Practice: * Covers structural and ground deformation monitoring analysis, advanced techniques in mining and tunneling surveys, and high precision alignment of engineering structures *...

Precision structural engineering of self-rolled-up 3D nanomembranes guided by transient quasi-static FEM modeling.

Science.gov (United States)

Huang, Wen; Koric, Seid; Yu, Xin; Hsia, K Jimmy; Li, Xiuling

2014-11-12

Micro- and nanoscale tubular structures can be formed by strain-induced self-rolled-up nanomembranes. Precision engineering of the shape and dimension determines the performance of devices based on this platform for electronic, optical, and biological applications. A transient quasi-static finite element method (FEM) with moving boundary conditions is proposed as a general approach to design diverse types of three-dimensional (3D) rolled-up geometries. This method captures the dynamic release process of membranes through etching driven by mismatch strain and accurately predicts the final dimensions of rolled-up structures. Guided by the FEM modeling, experimental demonstration using silicon nitride membranes was achieved with unprecedented precision including controlling fractional turns of a rolled-up membrane, anisotropic rolling to form helical structures, and local stress control for 3D hierarchical architectures.

Supporting deployed operations: are military nurses gaining the relevant experience from MDHUs to be competent in deployed operations?

Science.gov (United States)

Beaumont, Steven P; Allan, Helen T

2014-01-01

To explore how peacetime employment of military nurses in the UK National Health Service Medical Defence Hospital Units prepares them to be competent to practise in their role on deployment. Military secondary care nurses are employed within UK National Health Service Trusts to gain clinical experience that will be relevant to their military nursing role. A two-stage grounded theory study using mixed methods: postal questionnaire survey and in-depth interviews. In stage one a postal questionnaire was distributed to all serving military nurses. Stage two involved 12 semi-structured interviews. The data from both parts of the study were analysed using grounded theory. Four categories and one core category were identified, which suggested that participants did not feel fully prepared for deployment. Their feelings of preparedness increased with deployment experience and decreased when the nature of injuries seen on deployment changed. Respondents argued that even when unprepared, they did not feel incompetent. The findings suggest that the peacetime clinical experience gained in the National Health Service did not always develop the necessary competencies to carry out roles as military nurses on deployment. This study highlights the unique role of military nurses. We discuss these findings in the light of the literature on competency and expertise. The military nurses in this study did not feel fully prepared for deployed operations. We propose a new model for how military nurses could gain relevant experience from their National Health Service placements. National Health Service clinical placements need to be reassessed regularly to ensure that they are meeting military nurses' clinical requirements. Experiences of nurses returning from deployment could be shared and used as a basis for reflection and learning within National Health Service Trusts and also inform decisions regarding the appropriateness of clinical placements for qualified military nurses. © 2012

Precision muonium spectroscopy

International Nuclear Information System (INIS)

Jungmann, Klaus P.

2016-01-01

The muonium atom is the purely leptonic bound state of a positive muon and an electron. It has a lifetime of 2.2 µs. The absence of any known internal structure provides for precision experiments to test fundamental physics theories and to determine accurate values of fundamental constants. In particular ground state hyperfine structure transitions can be measured by microwave spectroscopy to deliver the muon magnetic moment. The frequency of the 1s–2s transition in the hydrogen-like atom can be determined with laser spectroscopy to obtain the muon mass. With such measurements fundamental physical interactions, in particular quantum electrodynamics, can also be tested at highest precision. The results are important input parameters for experiments on the muon magnetic anomaly. The simplicity of the atom enables further precise experiments, such as a search for muonium–antimuonium conversion for testing charged lepton number conservation and searches for possible antigravity of muons and dark matter. (author)

Mastering Windows 7 Deployment

CERN Document Server

Finn, Aidan; van Surksum, Kenneth

2011-01-01

Get professional-level instruction on Windows 7 deployment tools Enterprise-level operating system deployment is challenging and requires knowledge of specific tools. It is expected that Windows 7 will be extensively deployed in businesses worldwide. This comprehensive Sybex guide provides thorough coverage of the Microsoft deployment tools that were specifically created for Windows 7, preparing system administrators, MIS professionals, and corporate programmers to tackle the task effectively.Companies worldwide are expected to deploy Windows 7 as their enterprise operating system; system admi

Challenges to Deploy Service Design in Organizations

DEFF Research Database (Denmark)

Akasaka, Fumiya; Ohno, Takehiko; Jensen, Mika Yasuoka

2016-01-01

More and more companies are applying service design approaches to develop services and products. Not every project, however, has achieved its goals. In many cases, difficulties arise from organizational issues such as organization structure and evaluation system. In this research, we held workshops...... where success and failure factors of service design projects in organization are presented. By analysing the results, we construct a model that explains the “difficulties of deploying the service design approach in organization.” On the basis of the model, this paper discusses the challenges...... to the deployment of the service design approach in organizations....

Seismic Structure of Perth Basin (Australia) and surroundings from Passive Seismic Deployments

Science.gov (United States)

Issa, N.; Saygin, E.; Lumley, D. E.; Hoskin, T. E.

2016-12-01

We image the subsurface structure of Perth Basin, Western Australia and surroundings by using ambient seismic noise data from 14 seismic stations recently deployed by University of Western Australia (UWA) and other available permanent stations from Geoscience Australia seismic network and the Australian Seismometers in Schools program. Each of these 14 UWA seismic stations comprises a broadband sensor and a high fidelity 3-component 10 Hz geophone, recording in tandem at 250 Hz and 1000 Hz. The other stations used in this study are equipped with short period and broadband sensors. In addition, one shallow borehole station is operated with eight 3 component geophones at depths of between 2 and 44 m. The network is deployed to characterize natural seismicity in the basin and to try and identify any microseismic activity across Darling Fault Zone (DFZ), bounding the basin to the east. The DFZ stretches to approximately 1000 km north-south in Western Australia, and is one of the longest fault zones on the earth with a limited number of detected earthquakes. We use seismic noise cross- and auto-correlation methods to map seismic velocity perturbations across the basin and the transition from DFZ to the basin. Retrieved Green's functions are stable and show clear dispersed waveforms. Travel times of the surface wave Green's functions from noise cross-correlations are inverted with a two-step probabilistic framework to map the absolute shear wave velocities as a function of depth. The single station auto-correlations from the seismic noise yields P wave reflectivity under each station, marking the major discontinuities. Resulting images show the shear velocity perturbations across the region. We also quantify the variation of ambient seismic noise at different depths in the near surface using the geophones in the shallow borehole array.

Space Situational Awareness of Large Numbers of Payloads From a Single Deployment

Science.gov (United States)

Segerman, A.; Byers, J.; Emmert, J.; Nicholas, A.

2014-09-01

The nearly simultaneous deployment of a large number of payloads from a single vehicle presents a new challenge for space object catalog maintenance and space situational awareness (SSA). Following two cubesat deployments last November, it took five weeks to catalog the resulting 64 orbits. The upcoming Kicksat mission will present an even greater SSA challenge, with its deployment of 128 chip-sized picosats. Although all of these deployments are in short-lived orbits, future deployments will inevitably occur at higher altitudes, with a longer term threat of collision with active spacecraft. With such deployments, individual scientific payload operators require rapid precise knowledge of their satellites' locations. Following the first November launch, the cataloguing did not initially associate a payload with each orbit, leaving this to the satellite operators. For short duration missions, the time required to identify an experiment's specific orbit may easily be a large fraction of the spacecraft's lifetime. For a Kicksat-type deployment, present tracking cannot collect enough observations to catalog each small object. The current approach is to treat the chip cloud as a single catalog object. However, the cloud dissipates into multiple subclouds and, ultimately, tiny groups of untrackable chips. One response to this challenge may be to mandate installation of a transponder on each spacecraft. Directional transponder transmission detections could be used as angle observations for orbit cataloguing. Of course, such an approach would only be employable with cooperative spacecraft. In other cases, a probabilistic association approach may be useful, with the goal being to establish the probability of an element being at a given point in space. This would permit more reliable assessment of the probability of collision of active spacecraft with any cloud element. This paper surveys the cataloguing challenges presented by large scale deployments of small spacecraft

Precision Diagnosis, Monitoring and Control of Structural Component Degradation in Nuclear Power Plants

International Nuclear Information System (INIS)

Han, J. H.; Choi, M. S.; Lee, D. H.; Hur, D. H.; Na, J. W.; Kim, K. M.; Hong, J. H.; Kim, H. S.

2007-06-01

The occurrence of structural material degradations in NPPs and their progress during operation are directly related to the safety and the integrity of NPPs. The various kinds of material degradation are usually examined by methods of material integrity evaluation and non-destructive evaluation(NDE). Material integrity evaluation is well known as classical method to interpret cause and mechanism of degradation and failure, however, this method has a limitation of detection and diagnosis for actual condition of flaws and defects occurring during plant operation, particularly for their formation in the early stage. NDE used widely for detection of defects formed on structural materials provides many information for safety regulation, plant management, repairing, however, this technique has a generic problem in its reliability due to low detectability and ability of signal analysis, etc. The objective of this research project is to develop the advanced technologies ensuring a precision diagnosis on the various kind of defects in structural materials of NPP and a high performance in material degradation evaluation. Many of the advanced technologies were developed in the 1st phase of this project. They contributed to interpret more precisely the root causes of degradation, failure and to establish the proper measures for the safety and integrity of NPPs. The accomplishment of comprehensive technology developed as planned will be practically applied to the nuclear industries and contributed to improve the safety and integrity of NPPs

Realization and testing of a deployable space telescope based on tape springs

Science.gov (United States)

Lei, Wang; Li, Chuang; Zhong, Peifeng; Chong, Yaqin; Jing, Nan

2017-08-01

For its compact size and light weight, space telescope with deployable support structure for its secondary mirror is very suitable as an optical payload for a nanosatellite or a cubesat. Firstly the realization of a prototype deployable space telescope based on tape springs is introduced in this paper. The deployable telescope is composed of primary mirror assembly, secondary mirror assembly, 6 foldable tape springs to support the secondary mirror assembly, deployable baffle, aft optic components, and a set of lock-released devices based on shape memory alloy, etc. Then the deployment errors of the secondary mirror are measured with three-coordinate measuring machine to examine the alignment accuracy between the primary mirror and the deployed secondary mirror. Finally modal identification is completed for the telescope in deployment state to investigate its dynamic behavior with impact hammer testing. The results of the experimental modal identification agree with those from finite element analysis well.

Structural design of the Large Deployable Reflector (LDR)

Science.gov (United States)

Satter, Celeste M.; Lou, Michael C.

1991-01-01

An integrated Large Deployable Reflector (LDR) analysis model was developed to enable studies of system responses to the mechanical and thermal disturbances anticipated during on-orbit operations. Functional requirements of the major subsystems of the LDR are investigated, design trades are conducted, and design options are proposed. System mass and inertia properties are computed in order to estimate environmental disturbances, and in the sizing of control system hardware. Scaled system characteristics are derived for use in evaluating launch capabilities and achievable orbits. It is concluded that a completely passive 20-m primary appears feasible for the LDR from the standpoint of both mechanical vibration and thermal distortions.

Structural design of the Large Deployable Reflector (LDR)

Science.gov (United States)

Satter, Celeste M.; Lou, Michael C.

1991-09-01

An integrated Large Deployable Reflector (LDR) analysis model was developed to enable studies of system responses to the mechanical and thermal disturbances anticipated during on-orbit operations. Functional requirements of the major subsystems of the LDR are investigated, design trades are conducted, and design options are proposed. System mass and inertia properties are computed in order to estimate environmental disturbances, and in the sizing of control system hardware. Scaled system characteristics are derived for use in evaluating launch capabilities and achievable orbits. It is concluded that a completely passive 20-m primary appears feasible for the LDR from the standpoint of both mechanical vibration and thermal distortions.

LDR structural experiment definition

Science.gov (United States)

Russell, R. A.

1988-01-01

A system study to develop the definition of a structural flight experiment for a large precision segmented reflector on the Space Station was accomplished by the Boeing Aerospace Company for NASA's Langley Research Center. The objective of the study was to use a Large Deployable Reflector (LDR) baseline configuration as the basis for focusing an experiment definition, so that the resulting accommodation requirements and interface constraints could be used as part of the mission requirements data base for Space Station. The primary objectives of the first experiment are to construct the primary mirror support truss and to determine its structural and thermal characteristics. Addition of an optical bench, thermal shield and primary mirror segments, and alignment of the optical components, would occur on a second experiment. The structure would then be moved to the payload point system for pointing, optical control, and scientific optical measurement for a third experiment. Experiment 1 will deploy the primary support truss while it is attached to the instrument module structure. The ability to adjust the mirror attachment points and to attach several dummy primary mirror segments with a robotic system will also be demonstrated. Experiment 2 will be achieved by adding new components and equipment to experiment one. Experiment 3 will demonstrate advanced control strategies, active adjustment of the primary mirror alignment, and technologies associated with optical sensing.

Pre-deployment dissociation and personality as risk factors for post-deployment post-traumatic stress disorder in Danish soldiers deployed to Afghanistan

DEFF Research Database (Denmark)

Ponce de León, Beatriz; Andersen, Søren; Karstoft, Karen Inge

2018-01-01

Objective: This study investigated whether pre-deployment dissociation was associated with previously identified post-traumatic stress disorder (PTSD) symptom trajectories from before to 2.5 years after military deployment. Furthermore, it examined whether the tendency to dissociate, pre-deployme......Objective: This study investigated whether pre-deployment dissociation was associated with previously identified post-traumatic stress disorder (PTSD) symptom trajectories from before to 2.5 years after military deployment. Furthermore, it examined whether the tendency to dissociate, pre...

Design and Analysis Tools for Deployable Solar Array Systems, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Large, lightweight, deployable solar array structures have been identified as a key enabling technology for NASA with analysis and design of these structures being...

Design and Analysis Tools for Deployable Solar Array Systems, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — Large, lightweight, deployable solar array structures have been identified as a key enabling technology for NASA with analysis and design of these structures being...

Verify Occulter Deployment Tolerances as Part of NASA's Technology Development for Exoplanet Missions

Science.gov (United States)

Kasdin, N. J.; Shaklan, S.; Lisman, D.; Thomson, M.; Webb, D.; Cady, E.; Marks, G. W.; Lo, A.

2013-01-01

In support of NASA's Exoplanet Exploration Program and the Technology Development for Exoplanet Missions (TDEM), we recently completed a 2 year study of the manufacturability and metrology of starshade petals. An external occult is a satellite employing a large screen, or starshade, that flies in formation with a spaceborne telescope to provide the starlight suppression needed for detecting and characterizing exoplanets. Among the advantages of using an occulter are the broadband allowed for characterization and the removal of light before entering the observatory, greatly relaxing the requirements on the telescope and instrument. This poster presents the results of our successful first TDEM that demonstrated an occulter petal could be built and measured to an accuracy consistent with close to 10^-10 contrast. We also present the progress in our second TDEM to demonstrate the next critical technology milestone: precision deployment of the central truss and petals to the necessary accuracy. We have completed manufacture of four sub-scale petals and a central hub to fit with an existing deployable truss. We show the plans for repeated stow and deploy tests of the assembly and the metrology to confirm that each deploy repeatably meets the absolute positioning requirements of the petals (better than 1.0 mm).

Design study of the precision optical calibration module for the PINGU detector

Energy Technology Data Exchange (ETDEWEB)

Veenkamp, Joost; Krings, Kai [TU Muenchen, Physik-Department, Excellence Cluster Universe, Boltzmannstr. 2, 85748 Garching (Germany); Collaboration: IceCube-Collaboration

2015-07-01

The Precision IceCube Next Generation Upgrade (PINGU) will measure atmospheric neutrinos with a threshold of a few GeV. The primary goal for this extension is to determine the Neutrino mass hierarchy. A new level of precision is needed in order to reach this. The calibration of the DOM's is an important aspect in raising the precision to the needed level. A better calibration system will enable a better understanding of the ice and will therefore significantly reduce systematic effects. We present the Precision Optical Calibration Module (POCAM). By keeping the outer topology identical to that of the DOM, cost effective construction and deployment is ensured. The design of the POCAM is based on the principle of the integrating sphere. An appropriately placed LED in combination with a diffusive layer on the inside of the sphere results in an isotropic light emission from the apertures in the spherical housing. The output of the LED is controllable and known to high precision, it therefore ensures control over the output from the apertures. We report on the first investigations.

Verifying occulter deployment tolerances as part of NASA's technology development for exoplanet missions

Science.gov (United States)

Kasdin, N. J.; Lisman, D.; Shaklan, S.; Thomson, M.; Webb, D.; Cady, E.; Marks, G. W.; Lo, A.

2013-09-01

An external occulter is a satellite employing a large screen, or starshade, that flies in formation with a spaceborne telescope to provide the starlight suppression needed for detecting and characterizing exoplanets. Among the advantages of using an occulter are the broadband allowed for characterization and the removal of light before entering the observatory, greatly relaxing the requirements on the telescope and instrument. In support of NASA's Exoplanet Exploration Program and the Technology Development for Exoplanet Missions (TDEM), we recently completed a 2 year study of the manufacturability and metrology of starshade petals. In this paper we review the results of that successful first TDEM which demonstrated an occulter petal could be built and measured to an accuracy consistent with close to 10-10 contrast. We then present the results of our second TDEM to demonstrate the next critical technology milestone: precision deployment of the central truss and petals to the necessary accuracy. We show the deployment of an existing deployable truss outfitted with four sub-scale petals and a custom designed central hub.

A Testbed to Evaluate the FIWARE-Based IoT Platform in the Domain of Precision Agriculture

Science.gov (United States)

Martínez, Ramón; Pastor, Juan Ángel; Álvarez, Bárbara; Iborra, Andrés

2016-01-01

Wireless sensor networks (WSNs) represent one of the most promising technologies for precision farming. Over the next few years, a significant increase in the use of such systems on commercial farms is expected. WSNs present a number of problems, regarding scalability, interoperability, communications, connectivity with databases and data processing. Different Internet of Things middleware is appearing to overcome these challenges. This paper checks whether one of these middleware, FIWARE, is suitable for the development of agricultural applications. To the authors’ knowledge, there are no works that show how to use FIWARE in precision agriculture and study its appropriateness, its scalability and its efficiency for this kind of applications. To do this, a testbed has been designed and implemented to simulate different deployments and load conditions. The testbed is a typical FIWARE application, complete, yet simple and comprehensible enough to show the main features and components of FIWARE, as well as the complexity of using this technology. Although the testbed has been deployed in a laboratory environment, its design is based on the analysis of an Internet of Things use case scenario in the domain of precision agriculture. PMID:27886091

First results of the deployment of a SoLid detector module at the SCK•CEN BR2 reactor

Science.gov (United States)

Ryder, N.

The SoLid experiment aims to resolve the reactor neutrino anomaly by searching for electron-to-sterile anti-neutrino oscillations. The search will be performed between 5.5 and 10 m from the highly enriched uranium core of the BR2 reactor at SCK-CEN. The experiment utilises a novel approach to anti-neutrino detection based on a highly segmented, composite scintillator detector design. High experimental sensitivity can be achieved using a combination of high neutron-gamma discrimination using 6 LiF:ZnS(Ag) and precise localisation of the inverse beta decay products. This compact detector system requires limited passive shielding as it relies on spacial topology to determine the different classes of backgrounds. The first full scale, 288 kg, detector module was deployed at the BR2 reactor in November 2014. A phased three tonne experimental deployment will begin in the second half of 2016, allowing a precise search for oscillations that will resolve the reactor anomaly using a three tonne detector running for three years. In this talk the novel detector design is explained and initial detector performance results from the module level deployment are presented along with an estimation of the physics reach of the next phase.

Precision and accuracy in smFRET based structural studies—A benchmark study of the Fast-Nano-Positioning System

Science.gov (United States)

Nagy, Julia; Eilert, Tobias; Michaelis, Jens

2018-03-01

Modern hybrid structural analysis methods have opened new possibilities to analyze and resolve flexible protein complexes where conventional crystallographic methods have reached their limits. Here, the Fast-Nano-Positioning System (Fast-NPS), a Bayesian parameter estimation-based analysis method and software, is an interesting method since it allows for the localization of unknown fluorescent dye molecules attached to macromolecular complexes based on single-molecule Förster resonance energy transfer (smFRET) measurements. However, the precision, accuracy, and reliability of structural models derived from results based on such complex calculation schemes are oftentimes difficult to evaluate. Therefore, we present two proof-of-principle benchmark studies where we use smFRET data to localize supposedly unknown positions on a DNA as well as on a protein-nucleic acid complex. Since we use complexes where structural information is available, we can compare Fast-NPS localization to the existing structural data. In particular, we compare different dye models and discuss how both accuracy and precision can be optimized.

Development of the Aquarius Antenna Deployment Mechanisms and Spring/Damper Actuator

Science.gov (United States)

Johnson, Joel A.

2008-01-01

The Aquarius Instrument s large radar reflector dish needed to be stowed for launch, and then deployed on-orbit. The Deployment Subsystem consisted of a cantilevered boom structure and two single-axis hinge mechanisms to accurately deploy and position the reflector dish relative to the radar feed horns. The cantilevered design demanded high stiffness and accuracy from the deployment mechanism at the root of the boom. A preload-generating end-of-travel latch was also required. To largely eliminate the need for control systems, each deployment mechanism was actuated by a passive spring motor with viscous-fluid damping. Tough requirements and adaptation of a heritage actuator to the new application resulted in numerous challenges. Fabrication, assembly, and testing encountered additional problems, though ultimately the system was demonstrated very successfully. This paper revisits the development to highlight which design concepts worked and the many important lessons learned.

Gravity sag of sandwich panel assemblies as applied to precision cathode strip chamber structural design

International Nuclear Information System (INIS)

Horvath, J.

1993-01-01

The relationship between gravity sag of a precision cathode strip chamber and its sandwich panel structural design is explored parametrically. An algorithm for estimating the dominant component of gravity sag is defined. Graphs of normalized gravity sag as a function of gap frame width and material, sandwich core edge filler width and material, panel skin thickness, gap height, and support location are calculated using the gravity sag algorithm. The structural importance of the sandwich-to-sandwich ''gap frame'' connection is explained

A wireless sensor network design and evaluation for large structural strain field monitoring

International Nuclear Information System (INIS)

Qiu, Zixue; Wu, Jian; Yuan, Shenfang

2011-01-01

Structural strain changes under external environmental or mechanical loads are the main monitoring parameters in structural health monitoring or mechanical property tests. This paper presents a wireless sensor network designed for monitoring large structural strain field variation. First of all, a precision strain sensor node is designed for multi-channel strain gauge signal conditioning and wireless monitoring. In order to establish a synchronous strain data acquisition network, the cluster-star network synchronization method is designed in detail. To verify the functionality of the designed wireless network for strain field monitoring capability, a multi-point network evaluation system is developed for an experimental aluminum plate structure for load variation monitoring. Based on the precision wireless strain nodes, the wireless data acquisition network is deployed to synchronously gather, process and transmit strain gauge signals and monitor results under concentrated loads. This paper shows the efficiency of the wireless sensor network for large structural strain field monitoring

IEA Wind Task 23 Offshore Wind Technology and Deployment. Subtask 1 Experience with Critical Deployment Issues. Final Technical Report

DEFF Research Database (Denmark)

Lemming, Jørgen Kjærgaard

The final report for IEA Wind Task 23, Offshore Wind Energy Technology and Deployment, is made up of two separate reports: Subtask 1: Experience with Critical Deployment Issues and Subtask 2: Offshore Code Comparison Collaborative (OC3). The Subtask 1 report included here provides background...... information and objectives of Task 23. It specifically discusses ecological issues and regulation, electrical system integration and offshore wind, external conditions, and key conclusions for Subtask 1. The Subtask 2 report covers OC3 background information and objectives of the task, OC3 benchmark exercises...... of aero-elastic offshore wind turbine codes, monopile foundation modeling, tripod support structure modeling, and Phase IV results regarding floating wind turbine modeling....

Remotely deployable aerial inspection using tactile sensors

Science.gov (United States)

MacLeod, C. N.; Cao, J.; Pierce, S. G.; Sullivan, J. C.; Pipe, A. G.; Dobie, G.; Summan, R.

2014-02-01

For structural monitoring applications, the use of remotely deployable Non-Destructive Evaluation (NDE) inspection platforms offer many advantages, including improved accessibility, greater safety and reduced cost, when compared to traditional manual inspection techniques. The use of such platforms, previously reported by researchers at the University Strathclyde facilitates the potential for rapid scanning of large areas and volumes in hazardous locations. A common problem for both manual and remote deployment approaches lies in the intrinsic stand-off and surface coupling issues of typical NDE probes. The associated complications of these requirements are obviously significantly exacerbated when considering aerial based remote inspection and deployment, resulting in simple visual techniques being the preferred sensor payload. Researchers at Bristol Robotics Laboratory have developed biomimetic tactile sensors modelled on the facial whiskers (vibrissae) of animals such as rats and mice, with the latest sensors actively sweeping their tips across the surface in a back and forth motion. The current work reports on the design and performance of an aerial inspection platform and the suitability of tactile whisking sensors to aerial based surface monitoring applications.

Mastering Hyper-V Deployment

CERN Document Server

Finn, Aidan

2010-01-01

The only book to take an in-depth look at deploying Hyper-V. Now in its second generation, the popular Hyper-V boasts technical advances that create even more dynamic systems than ever before. This unique resource serves an authoritative guide to deploying Windows Server 2008 R2 Hyper-V comprehensively. Step-by-step instructions demonstrate how to design a Hyper-V deployment, build a Hyper-V host environment, and design a management system with System Center Virtual Machine Manager 2008 R2.: Features real-world examples that show you how to design a Hyper-V deployment, build a Hyper-V host env

Tensions in ethics and policy created by National Precision Medicine Programs.

Science.gov (United States)

Minari, Jusaku; Brothers, Kyle B; Morrison, Michael

2018-04-17

Precision medicine promises to use genomics and other data-intensive approaches to improve diagnosis and develop new treatments for major diseases, but also raises a range of ethical and governance challenges. Implementation of precision medicine in "real world" healthcare systems blurs the boundary between research and care. This has implications for the meaning and validity of consent, and increased potential for discrimination, among other challenges. Increased sharing of personal information raises concerns about privacy, commercialization, and public trust. This paper considers national precision medicine schemes from the USA, the UK, and Japan, comparing how these challenges manifest in each national context and examining the range of approaches deployed to mitigate the potential undesirable social consequences. There is rarely a "one size" fits all solution to these complex problems, but the most viable approaches are those which take account of cultural preferences and attitudes, available resources, and the wider political landscape in which national healthcare systems are embedded.

Solar sail deployment experiment

OpenAIRE

Shimose, Shigeru; 下瀬　滋

2006-01-01

Solar Sail move by receiving momentum of photons in sunlight. This paper presents results of some Spin-Stabilized Solar Sail deployment experiment. ISAS has successfully deployed, for the first time in the world, the polyimide Solar Sail taking advantage of centrifugal force in space. Based on this result, the new deployment mechanism is being developed which retracts the 50 m diameter sail.

CMS software deployment on OSG

International Nuclear Information System (INIS)

Kim, B; Avery, P; Thomas, M; Wuerthwein, F

2008-01-01

A set of software deployment tools has been developed for the installation, verification, and removal of a CMS software release. The tools that are mainly targeted for the deployment on the OSG have the features of instant release deployment, corrective resubmission of the initial installation job, and an independent web-based deployment portal with Grid security infrastructure login mechanism. We have been deploying over 500 installations and found the tools are reliable and adaptable to cope with problems with changes in the Grid computing environment and the software releases. We present the design of the tools, statistics that we gathered during the operation of the tools, and our experience with the CMS software deployment on the OSG Grid computing environment

CMS software deployment on OSG

Energy Technology Data Exchange (ETDEWEB)

Kim, B; Avery, P [University of Florida, Gainesville, FL 32611 (United States); Thomas, M [California Institute of Technology, Pasadena, CA 91125 (United States); Wuerthwein, F [University of California at San Diego, La Jolla, CA 92093 (United States)], E-mail: bockjoo@phys.ufl.edu, E-mail: thomas@hep.caltech.edu, E-mail: avery@phys.ufl.edu, E-mail: fkw@fnal.gov

2008-07-15

A set of software deployment tools has been developed for the installation, verification, and removal of a CMS software release. The tools that are mainly targeted for the deployment on the OSG have the features of instant release deployment, corrective resubmission of the initial installation job, and an independent web-based deployment portal with Grid security infrastructure login mechanism. We have been deploying over 500 installations and found the tools are reliable and adaptable to cope with problems with changes in the Grid computing environment and the software releases. We present the design of the tools, statistics that we gathered during the operation of the tools, and our experience with the CMS software deployment on the OSG Grid computing environment.

Techno-Economics of Residential Broadband Deployment

DEFF Research Database (Denmark)

Sigurdsson, Halldor Matthias

2007-01-01

on account of their existing telecom network (”the raw copper”), and typically they will prefer an xDSL-based strategy (various types of Digital Subscriber Line-technology: ADSL, VDSL, etc.), where the rate of speed of data connections are increased gradually to 10-50 Mbit/s or even more, in order to gain...... broadband deployment strategy is depending on a complexed set of parameters, and there is a demand for precise techno-economic cost models estimating financial feasibility. The existing cost models do not consider the dynamic developments in the market caused by competition. The PhD thesis has a profound...... the general principles from the Danish LRAIC-model (Long Run Average Incremental Cost) and divides Denmark in 4 geografical profiles. Considering the existing copper-infrastructure the most advantageous strategies for the players of each of these profiles are identified. The importance of the time horizon...

Development of corotational formulated FEM for application to 30m class large deployable reflector

International Nuclear Information System (INIS)

Ozawa, Satoru; Fujiwara, Yuuichi; Tsujihata, Akio

2010-01-01

JAXA, Japan Aerospace Exploration Agency, is now developing a corotational formulated finite element analysis method and its software 'Origami/ETS' for the development of 30m class large deployable reflectors. For the reason that the deployable reflector is composed of beams, cables and mesh, this analysis method is generalized for finite elements with multiple nodes, which are commonly used in linear finite element analyses. The large displacement and rotation are taken into account by the corotational formulation. The tangent stiffness matrix for finite elements with multiple nodes is obtained as follows; the geometric stiffness matrix of two node elements is derived by taking variation of the element's corotational matrix from the virtual work of finite elements with large displacement; similarly the geometric stiffness matrix for three node elements is derived; as the extension of two and three node element theories, the geometric stiffness matrix for multiple node elements is derived; with the geometric stiffness matrix for multiple node elements, the tangent stiffness matrix is obtained. The analysis method is applied for the deployment analysis and static structural analysis of the 30m class large deployable reflector. In the deployment analysis, it is confirmed that this method stably analyzes the deployment motion from the deployment configuration to the stowed configuration of the reflector. In the static analysis, it is confirmed that the mesh structure is analyzed successfully. The 30m class large deployable reflector is now still being developed and is about to undergo several tests with its prototypes. This analysis method will be used in the tests and verifications of the reflector.

A Road Map for Precision Medicine in the Epilepsies

Science.gov (United States)

2015-01-01

Summary Technological advances have paved the way for accelerated genomic discovery and are bringing precision medicine clearly into view. Epilepsy research in particular is well-suited to serve as a model for the development and deployment of targeted therapeutics in precision medicine because of the rapidly expanding genetic knowledge base in epilepsy, the availability of good in vitro and in vivo model systems to efficiently study the biological consequences of genetic mutations, the ability to turn these models into effective drug screening platforms, and the establishment of collaborative research groups. Moving forward, it is critical that we strengthen these collaborations, particularly through integrated research platforms to provide robust analyses both for accurate personal genome analysis and gene and drug discovery. Similarly, the implementation of clinical trial networks will allow the expansion of patient sample populations with genetically defined epilepsy so that drug discovery can be translated into clinical practice. PMID:26416172

Development of High Precision Tsunami Runup Calculation Method Coupled with Structure Analysis

Science.gov (United States)

Arikawa, Taro; Seki, Katsumi; Chida, Yu; Takagawa, Tomohiro; Shimosako, Kenichiro

2017-04-01

The 2011 Great East Japan Earthquake (GEJE) has shown that tsunami disasters are not limited to inundation damage in a specified region, but may destroy a wide area, causing a major disaster. Evaluating standing land structures and damage to them requires highly precise evaluation of three-dimensional fluid motion - an expensive process. Our research goals were thus to develop a coupling STOC-CADMAS (Arikawa and Tomita, 2016) coupling with the structure analysis (Arikawa et. al., 2009) to efficiently calculate all stages from tsunami source to runup including the deformation of structures and to verify their applicability. We also investigated the stability of breakwaters at Kamaishi Bay. Fig. 1 shows the whole of this calculation system. The STOC-ML simulator approximates pressure by hydrostatic pressure and calculates the wave profiles based on an equation of continuity, thereby lowering calculation cost, primarily calculating from a e epi center to the shallow region. As a simulator, STOC-IC solves pressure based on a Poisson equation to account for a shallower, more complex topography, but reduces computation cost slightly to calculate the area near a port by setting the water surface based on an equation of continuity. CS3D also solves a Navier-Stokes equation and sets the water surface by VOF to deal with the runup area, with its complex surfaces of overflows and bores. STR solves the structure analysis including the geo analysis based on the Biot's formula. By coupling these, it efficiently calculates the tsunami profile from the propagation to the inundation. The numerical results compared with the physical experiments done by Arikawa et. al.,2012. It was good agreement with the experimental ones. Finally, the system applied to the local situation at Kamaishi bay. The almost breakwaters were washed away, whose situation was similar to the damage at Kamaishi bay. REFERENCES T. Arikawa and T. Tomita (2016): "Development of High Precision Tsunami Runup

Experimental and Analytical Evaluation of a Composite Honeycomb Deployable Energy Absorber

Science.gov (United States)

Jackson, Karen E.; Kellas, Sotiris; Horta, Lucas G.; Annett, Martin S.; Polanco, Michael A.; Littell, Justin D.; Fasanella, Edwin L.

2011-01-01

In 2006, the NASA Subsonic Rotary Wing Aeronautics Program sponsored the experimental and analytical evaluation of an externally deployable composite honeycomb structure that is designed to attenuate impact energy during helicopter crashes. The concept, which is designated the Deployable Energy Absorber (DEA), utilizes an expandable Kevlar honeycomb structure to dissipate kinetic energy through crushing. The DEA incorporates a unique flexible hinge design that allows the honeycomb to be packaged and stowed flat until needed for deployment. A variety of deployment options such as linear, radial, and/or hybrid methods can be used. Experimental evaluation of the DEA utilized a building block approach that included material characterization testing of its constituent, Kevlar -129 fabric/epoxy, and flexural testing of single hexagonal cells. In addition, the energy attenuation capabilities of the DEA were demonstrated through multi-cell component dynamic crush tests, and vertical drop tests of a composite fuselage section, retrofitted with DEA blocks, onto concrete, water, and soft soil. During each stage of the DEA evaluation process, finite element models of the test articles were developed and simulations were performed using the explicit, nonlinear transient dynamic finite element code, LS-DYNA. This report documents the results of the experimental evaluation that was conducted to assess the energy absorption capabilities of the DEA.

Dynamic analysis of the large deployable reflector

Science.gov (United States)

Calleson, Robert E.; Scott, A. Don

1987-01-01

The Large Deployable Reflector (LDR) is to be an astronomical observatory orbiting above Earth's obscuring atmosphere and operating in the spectral range between 30 microns and 1000 microns wavelength. The LDR will be used to study such astronomical phenomena as stellar and galactic formation, cosmology, and planetary atmospheres. The LDR will be the first observatory to be erected and assembled in space. This distinction brings with it several major technological challenges such as the development of ultra-lightweight deployable mirrors, advanced mirror fabrication techniques, advanced structures, and control of vibrations due to various sources of excitation. The purpose of this analysis is to provide an assessment of the vibrational response due to secondary mirror chopping and LDR slewing. The dynamic response of two 20-m LDR configurations was studied. Two mirror support configurations were investigated for the Ames concept, the first employs a six-strut secondary mirror support structure, while the second uses a triple-bipod support design. All three configurations were modeled using a tetrahedral truss design for the primary mirror support structure. Response resulting from secondary mirror chopping was obtained for the two Ames configurations, and the response of the primary mirror from slewing was obtained for all three configurations.

Gender differences in the effects of deployment-related stressors and pre-deployment risk factors on the development of PTSD symptoms in National Guard Soldiers deployed to Iraq and Afghanistan.

Science.gov (United States)

Polusny, Melissa A; Kumpula, Mandy J; Meis, Laura A; Erbes, Christopher R; Arbisi, Paul A; Murdoch, Maureen; Thuras, Paul; Kehle-Forbes, Shannon M; Johnson, Alexandria K

2014-02-01

Although women in the military are exposed to combat and its aftermath, little is known about whether combat as well as pre-deployment risk/protective factors differentially predict post-deployment PTSD symptoms among women compared to men. The current study assesses the influence of combat-related stressors and pre-deployment risk/protective factors on women's risk of developing PTSD symptoms following deployment relative to men's risk. Participants were 801 US National Guard Soldiers (712 men, 89 women) deployed to Iraq or Afghanistan who completed measures of potential risk/protective factors and PTSD symptoms one month before deployment (Time 1) and measures of deployment-related stressors and PTSD symptoms about 2-3 months after returning from deployment (Time 2). Men reported greater exposure to combat situations than women, while women reported greater sexual stressors during deployment than men. Exposure to the aftermath of combat (e.g., witnessing injured/dying people) did not differ by gender. At Time 2, women reported more severe PTSD symptoms and higher rates of probable PTSD than did men. Gender remained a predictor of higher PTSD symptoms after accounting for pre-deployment symptoms, prior interpersonal victimization, and combat related stressors. Gender moderated the association between several risk factors (combat-related stressors, prior interpersonal victimization, lack of unit support and pre-deployment concerns about life/family disruptions) and post-deployment PTSD symptoms. Elevated PTSD symptoms among female service members were not explained simply by gender differences in pre-deployment or deployment-related risk factors. Combat related stressors, prior interpersonal victimization, and pre-deployment concerns about life and family disruptions during deployment were differentially associated with greater post-deployment PTSD symptoms for women than men. Copyright © 2013 The Authors. Published by Elsevier Ltd.. All rights reserved.

Tether Deployer And Brake

Science.gov (United States)

Carroll, Joseph A.; Alexander, Charles M.

1993-01-01

Design concept promises speed, control, and reliability. Scheme for deploying tether provides for fast, free, and snagless payout and fast, dependable braking. Developed for small, expendable tethers in outer space, scheme also useful in laying transoceanic cables, deploying guidance wires to torpedoes and missiles, paying out rescue lines from ship to ship via rockets, deploying antenna wires, releasing communication and power cables to sonobuoys and expendable bathythermographs, and in reeling out lines from fishing rods.

Solar Photovoltaic Financing: Deployment by Federal Government Agencies

Energy Technology Data Exchange (ETDEWEB)

Cory, K.; Coggeshall, C.; Coughlin, J.; Kreycik, C.

2009-07-01

The goal of this report is to examine how federal agencies can finance on-site PV projects. It explains state-level cash incentives available, the importance of solar renewable energy certificate revenues (in certain markets), existing financing structures, as well as innovative financing structures being used by federal agencies to deploy on-site PV. Specific examples from the DOD, DOE, and other federal agencies are highlighted to explain federal project financing in detail.

Fusion Power Deployment

International Nuclear Information System (INIS)

Schmidt, J.A.; Ogden, J.M.

2002-01-01

Fusion power plants could be part of a future portfolio of non-carbon dioxide producing energy supplies such as wind, solar, biomass, advanced fission power, and fossil energy with carbon dioxide sequestration. In this paper, we discuss key issues that could impact fusion energy deployment during the last half of this century. These include geographic issues such as resource availability, scale issues, energy storage requirements, and waste issues. The resource needs and waste production associated with fusion deployment in the U.S. should not pose serious problems. One important feature of fusion power is the fact that a fusion power plant should be locatable within most local or regional electrical distribution systems. For this reason, fusion power plants should not increase the burden of long distance power transmission to our distribution system. In contrast to fusion power, regional factors could play an important role in the deployment of renewable resources such as wind, solar and biomass or fossil energy with CO2 sequestration. We examine the role of these regional factors and their implications for fusion power deployment

Deployment Analysis of a Simple Tape-Spring Hinge Using Probabilistic Methods

Science.gov (United States)

Lyle, Karen H.; Horta, Lucas G.

2012-01-01

Acceptance of new deployable structures architectures and concepts requires validated design methods to minimize the expense involved with technology validation flight testing. Deployable concepts for large lightweight spacecraft include booms, antennae, and masts. This paper explores the implementation of probabilistic methods in the design process for the deployment of a strain-energy mechanism, specifically a simple tape-spring hinge. Strain-energy mechanisms are attractive for deployment in very lightweight systems because they do not require the added mass and complexity associated with motors and controllers. However, designers are hesitant to include free deployment, strain-energy mechanisms because of the potential for uncontrolled behavior. In the example presented here, the tapespring cross-sectional dimensions have been varied and a target displacement during deployment has been selected as the design metric. Specifically, the tape-spring should reach the final position in the shortest time with the minimal amount of overshoot and oscillations. Surrogate models have been used to reduce computational expense. Parameter values to achieve the target response have been computed and used to demonstrate the approach. Based on these results, the application of probabilistic methods for design of a tape-spring hinge has shown promise as a means of designing strain-energy components for more complex space concepts.

TQM and lean strategy deployment in Italian hospitals.

Science.gov (United States)

Chiarini, Andrea; Baccarani, Claudio

2016-10-03

Purpose This paper aims to contribute to the debate concerning total quality management (TQM)-Lean strategy in public healthcare by analyzing the deployment path for implementation, the possible benefits that can be achieved and the encountered pitfalls. Design/methodology/approach Three case studies are drawn from three large Italian hospitals with more than 500 beds each and structured with many departments. The hospitals are located in Tuscany, Italy. These three hospitals have embraced TQM and Lean, starting from strategic objectives and their deployment. At the same time, they have also implemented many TQM-Lean tools. The case studies are based on interviews held with four managers in each of these three public hospitals. Findings Results from the interviews show that there is a specific deployment path for TQM-Lean implementation. The hospitals have also achieved benefits linked to patient satisfaction and improved organizational performances. Problems related to organizational and cultural issues, such as senior managers' commitment, staff management, manufacturing culture and tools adaptation, could affect the benefits. Research limitations/implications The research has been carried out in just three Italian public hospitals. Hence, similar investigations could be managed in other countries. Researchers could also use a larger sample and investigate these issues by means of quantitative inquiry. Practical implications Practitioners could try to apply the deployment path revealed by these case studies in other public and private hospitals. Originality/value The results of this research show that there is a specific, new deployment path for implementing TQM-Lean strategy in some public hospitals.

Base Station Antenna Pattern Distortion in Practical Urban Deployment Scenarios

DEFF Research Database (Denmark)

Rodriguez Larrad, Ignacio; Nguyen, Huan Cong; Sørensen, Troels Bundgaard

2014-01-01

In real urban deployments, base station antennas are typically not placed in free space conditions. Therefore, the radiation pattern can be affected by mounting structures and nearby obstacles located in the proximity of the antenna (near-field), which are often not taken into consideration. Also...... presents a combination of near-field and far-field simulations aimed to provide an overview of the distortion experienced by the base station antenna pattern in two different urban deployment scenarios: rooftop and telecommunications tower. The study illustrates how, in comparison with the near...

Precision digital control systems

Science.gov (United States)

Vyskub, V. G.; Rozov, B. S.; Savelev, V. I.

This book is concerned with the characteristics of digital control systems of great accuracy. A classification of such systems is considered along with aspects of stabilization, programmable control applications, digital tracking systems and servomechanisms, and precision systems for the control of a scanning laser beam. Other topics explored are related to systems of proportional control, linear devices and methods for increasing precision, approaches for further decreasing the response time in the case of high-speed operation, possibilities for the implementation of a logical control law, and methods for the study of precision digital control systems. A description is presented of precision automatic control systems which make use of electronic computers, taking into account the existing possibilities for an employment of computers in automatic control systems, approaches and studies required for including a computer in such control systems, and an analysis of the structure of automatic control systems with computers. Attention is also given to functional blocks in the considered systems.

Gossamer-1: Mission concept and technology for a controlled deployment of gossamer spacecraft

Science.gov (United States)

Seefeldt, Patric; Spietz, Peter; Sproewitz, Tom; Grundmann, Jan Thimo; Hillebrandt, Martin; Hobbie, Catherin; Ruffer, Michael; Straubel, Marco; Tóth, Norbert; Zander, Martin

2017-01-01

Gossamer structures for innovative space applications, such as solar sails, require technology that allows their controlled and thereby safe deployment. Before employing such technology for a dedicated science mission, it is desirable, if not necessary, to demonstrate its reliability with a Technology Readiness Level (TRL) of six or higher. The aim of the work presented here is to provide reliable technology that enables the controlled deployment and verification of its functionality with various laboratory tests, thereby qualifying the hardware for a first demonstration in low Earth orbit (LEO). The development was made in the Gossamer-1 project of the German Aerospace Center (DLR). This paper provides an overview of the Gossamer-1 mission and hardware development. The system is designed based on the requirements of a technology demonstration mission. The design rests on a crossed boom configuration with triangular sail segments. Employing engineering models, all aspects of the deployment were tested under ambient environment. Several components were also subjected to environmental qualification testing. An innovative stowing and deployment strategy for a controlled deployment, as well as the designs of the bus system, mechanisms and electronics are described. The tests conducted provide insights into the deployment process and allow a mechanical characterization of that deployment process, in particular the measurement of the deployment forces. Deployment on system level could be successfully demonstrated to be robust and controllable. The deployment technology is on TRL four approaching level five, with a qualification model for environmental testing currently being built.

High precision detector robot arm system

Science.gov (United States)

Shu, Deming; Chu, Yong

2017-01-31

A method and high precision robot arm system are provided, for example, for X-ray nanodiffraction with an X-ray nanoprobe. The robot arm system includes duo-vertical-stages and a kinematic linkage system. A two-dimensional (2D) vertical plane ultra-precision robot arm supporting an X-ray detector provides positioning and manipulating of the X-ray detector. A vertical support for the 2D vertical plane robot arm includes spaced apart rails respectively engaging a first bearing structure and a second bearing structure carried by the 2D vertical plane robot arm.

High-precision hyperfine structure measurement in slow atomic ion beams by collinear laser-rf double resonance

International Nuclear Information System (INIS)

Amarjit Sen; Childs, W.J.; Goodman, L.S.

1987-01-01

A new collinear laser-ion beam apparatus for slow ions (1 to 1.5 keV) has been built for measuring the hyperfine structure of metastable levels of ions with laser-rf double resonance technique. Narrow linewidths of ∼60 kHz (FWHM) have been observed for the first time in such systems. As a first application the hyperfine structure of the 4f 7 ( 8 S 0 )5d 9 D/sub J/ 0 metastable levels of /sup 151,153/Eu + has been measured with high precision. 10 refs., 8 figs

Deployable auxetic shape memory alloy cellular antenna demonstrator: design, manufacturing and modal testing

International Nuclear Information System (INIS)

Jacobs, S; Coconnier, C; DiMaio, D; Scarpa, F; Martinez, J; Toso, M

2012-01-01

This work describes the design, manufacturing and testing of a deployable antenna for deep-space missions based on a hybrid honeycomb truss made of shape memory alloy (SMA). The deployable characteristics are enhanced by the equivalent auxetic (negative Poisson’s ratio) behaviour of the cellular configuration. Specific emphasis is placed on the modal analysis techniques used to test the lightweight SMA structure. (paper)

Solar Photovoltaic Financing: Deployment on Public Property by State and Local Governments

Energy Technology Data Exchange (ETDEWEB)

Cory, K.; Coughlin, J.; Coggeshall, C.

2008-05-01

State and local governments have grown increasingly aware of the economic, environmental, and societal benefits of taking a lead role in U.S. implementation of renewable energy, particularly distributed photovoltaic (PV) installations. Recently, solar energy's cost premium has declined as a result of technology improvements and an increase in the cost of traditional energy generation. At the same time, a nationwide public policy focus on carbon-free, renewable energy has created a wide range of financial incentives to lower the costs of deploying PV even further. These changes have led to exponential increases in the availability of capital for solar projects, and tremendous creativity in the development of third-party ownership structures. As significant users of electricity, state and local governments can be an excellent example for solar PV system deployment on a national scale. Many public entities are not only considering deployment on public building rooftops, but also large-scale applications on available public lands. The changing marketplace requires that state and local governments be financially sophisticated to capture as much of the economic potential of a PV system as possible. This report examines ways that state and local governments can optimize the financial structure of deploying solar PV for public uses.

Demonstration of a Fast, Precise Propane Measurement Using Infrared Spectroscopy

Science.gov (United States)

Zahniser, M. S.; Roscioli, J. R.; Nelson, D. D.; Herndon, S. C.

2016-12-01

Propane is one of the primary components of emissions from natural gas extraction and processing activities. In addition to being an air pollutant, its ratio to other hydrocarbons such as methane and ethane can serve as a "fingerprint" of a particular facility or process, aiding in identifying emission sources. Quantifying propane has typically required laboratory analysis of flask samples, resulting in low temporal resolution and making plume-based measurements infeasible. Here we demonstrate fast (1-second), high precision (infrared spectroscopy at 2967 wavenumbers. In addition, we explore the impact of nearby water and ethane absorption lines on the accuracy and precision of the propane measurement. Finally, we discuss development of a dual-laser instrument capable of simultaneous measurements of methane, ethane, and propane (the C1-C3 compounds), all within a small spatial package that can be easily deployed aboard a mobile platform.

A low cost, high precision extreme/harsh cold environment, autonomous sensor data gathering and transmission platform.

Science.gov (United States)

Chetty, S.; Field, L. A.

2014-12-01

SWIMS III, is a low cost, autonomous sensor data gathering platform developed specifically for extreme/harsh cold environments. Arctic ocean's continuing decrease of summer-time ice is related to rapidly diminishing multi-year ice due to the effects of climate change. Ice911 Research aims to develop environmentally inert materials that when deployed will increase the albedo, enabling the formation and/preservation of multi-year ice. SWIMS III's sophisticated autonomous sensors are designed to measure the albedo, weather, water temperature and other environmental parameters. This platform uses low cost, high accuracy/precision sensors, extreme environment command and data handling computer system using satellite and terrestrial wireless solution. The system also incorporates tilt sensors and sonar based ice thickness sensors. The system is light weight and can be deployed by hand by a single person. This presentation covers the technical, and design challenges in developing and deploying these platforms.

Precision Muonium Spectroscopy

NARCIS (Netherlands)

Jungmann, Klaus P.

2016-01-01

The muonium atom is the purely leptonic bound state of a positive muon and an electron. It has a lifetime of 2.2 mu s. The absence of any known internal structure provides for precision experiments to test fundamental physics theories and to determine accurate values of fundamental constants. In

Tunable bandgaps in a deployable metamaterial

Science.gov (United States)

Nanda, Aditya; Karami, M. A.

2018-06-01

In this manuscript, we investigate deployable structures (such as solar arrays) and origami-inspired foldable structures as metamaterials capable of tunable wave manipulation. Specifically, we present a metamaterial whose bandgaps can be modulated by changing the fold angle of adjacent panels. The repeating unit cell of the structure consists of a beam (representing a panel) and a torsional spring (representing the folding mechanism). Two important cases are considered. Firstly, the fold angle (angle between adjacent beams), Ψ, is zero and only flexural waves propagate. In the second case, the fold angle is greater than zero (Ψ > 0). This causes longitudinal and transverse vibration to be coupled. FEM models are used to validate both these analyses. Increasing the fold angle was found to inflict notable changes to the wave transmission characteristics of the structure. In general, increasing the fold angles caused the bandwidth of bandgaps to increase. For the lowest four bandgaps we found bandwidth increases of 252 %, 177 %, 230 % and 163 % respectively at Ψ = 90 deg (relative to the bandwidths at Ψ = 0). In addition, non-trivial increases in bandwidth of the odd-numbered bandgaps occurs even at small fold angles-the bandwidth for the first and third bandgaps effectively double in size (increase by 100 %) at Ψ = 20 deg relative to those at Ψ = 0. This could have ramifications in the context of tunable wave manipulation and adaptive filtering. In addition, by expanding out the characteristic equation of transfer matrix for the straight structure, we prove that the upper band edge of the nth bandgap will always equal the nth simply supported natural frequency of the constituent beam. Further, we found that the ratio (EI/kt) is a pertinent parameter affecting the bandwidth of bandgaps. For low values of the ratio, effectively, no bandgap exists. For higher values of the ratio (EI/kt), we obtain a relatively large bandgap over which no waves propagate. This can

Part 8. Deployment considerations

International Nuclear Information System (INIS)

Dance, K.D.; Chang, Y.I.; Daly, T.A.

1980-01-01

This report addresses considerations of fast breeder reactor development and deployment from a national perspective. Nations vary greatly in their expertise and interest relative to nuclear power, and hence a single set of steps to be taken by a nation in decision-making on breeder development and deployment cannot be presented. The approach taken in this report is to present discussions on key factors influencing the breeder development and deployment decisions, especially in non-breeder nations, by drawing upon historical perspectives of the Light Water Reactor for comparison

A modified precise integration method based on Magnus expansion for transient response analysis of time varying dynamical structure

International Nuclear Information System (INIS)

Yue, Cong; Ren, Xingmin; Yang, Yongfeng; Deng, Wangqun

2016-01-01

This paper provides a precise and efficacious methodology for manifesting forced vibration response with respect to the time-variant linear rotational structure subjected to unbalanced excitation. A modified algorithm based on time step precise integration method and Magnus expansion is developed for instantaneous dynamic problems. The iterative solution is achieved by the ideology of transition and dimensional increment matrix. Numerical examples on a typical accelerating rotation system considering gyroscopic moment and mass unbalance force comparatively demonstrate the validity, effectiveness and accuracy with Newmark-β method. It is shown that the proposed algorithm has high accuracy without loss efficiency.

Comparing post-deployment mental health services utilization in soldiers deployed to Balkan, Iraq and Afghanistan

DEFF Research Database (Denmark)

Madsen, T; Sadowa Vedtofte, M; Nordentoft, M

2017-01-01

OBJECTIVE: Insight on how different missions have impacted rates of mental health service (MHS) utilization is unexplored. We compared postdeployment MHS utilization in a national cohort of first-time deployed to missions in Balkan, Iraq, and Afghanistan respectively. METHODS: A prospective...... national cohort study of 13 246 first-time deployed in the period 1996 through 2012 to missions in Balkan area, Iraq, or Afghanistan respectively. Soldiers 'MHS utilization was also compared with a 5:1 sex-, age-, and calendar year-matched never-deployed background population. Postdeployment utilization...... of psychotropics. RESULTS: Utilizing of psychiatric outpatient services and psychotropics was significantly higher in first-time deployed to Iraq and Afghanistan compared with deployed to Balkan. However, the rate of postdeployment admission to psychiatric hospital did not differ between missions. Postdeployment...

What pre-deployment and early post-deployment factors predict health function after combat deployment?: a prospective longitudinal study of Operation Enduring Freedom (OEF)/Operation Iraqi Freedom (OIF) soldiers.

Science.gov (United States)

McAndrew, Lisa M; D'Andrea, Elizabeth; Lu, Shou-En; Abbi, Bhavna; Yan, Grace W; Engel, Charles; Quigley, Karen S

2013-04-30

Physical and mental function are strong indicators of disability and mortality. OEF/OIF Veterans returning from deployment have been found to have poorer function than soldiers who have not deployed; however the reasons for this are unknown. A prospective cohort of 790 soldiers was assessed both pre- and immediately after deployment to determine predictors of physical and mental function after war. On average, OEF/OIF Veterans showed significant declines in both physical (t=6.65, pfunction (t=7.11, pdeployment function, poorer physical function after deployment was associated with older age, more physical symptoms, blunted systolic blood pressure reactivity and being injured. After controlling for pre-deployment function, poorer mental function after deployment was associated with younger age, lower social desirability, lower social support, greater physical symptoms and greater PTSD symptoms. Combat deployment was associated with an immediate decline in both mental and physical function. The relationship of combat deployment to function is complex and influenced by demographic, psychosocial, physiological and experiential factors. Social support and physical symptoms emerged as potentially modifiable factors.

Photovoltaic deployment strategy in Japan and the USA-an institutional appraisal

International Nuclear Information System (INIS)

Shum, Kwok L.; Watanabe, Chihiro

2007-01-01

PV as an information technology-like technology focusing upon user oriented customization to achieve deployment. Different models have different implications to the system engineering aspect of solar PV. A focus upon the standard grid-connected distributed category in the residential setting avoids the heavy customized engineering associated with many off-grid and one-off type projects. Japanese PV deployment strategy of concentrating upon a dominant category or niche with mass market potential also well matches the institutional structure of production [Coase, 1991. The Institutional Structure of Production, in Essays on Economics and Economists. The University of Chicago Press, Chicago] within the local PV technology suppliers industry. Major vertical integrated firms can facilitate system-related learning easier than a fragmented industry within the PV value chain with minimal transaction cost. This highly suggests that deployment strategy of PV or other renewable energy technologies must address the issues of adopting a globally developed technology to local (national) conditions and has strong institutional underpinnings in addition to financial subsidies, learning investment thinking

A stowing and deployment strategy for large membrane space systems on the example of Gossamer-1

Science.gov (United States)

Seefeldt, Patric

2017-09-01

Deployment systems for innovative space applications such as solar sails require a technique for a controlled and autonomous deployment in space. The deployment process has a strong impact on the mechanism and structural design and sizing. On the example of the design implemented in the Gossamer-1 project of the German Aerospace Center (DLR), such a stowing and deployment process is analyzed. It is based on a combination of zig-zag folding and coiling of triangular sail segments spanned between crossed booms. The deployment geometry and forces introduced by the mechanism considered are explored in order to reveal how the loads are transferred through the membranes to structural components such as the booms. The folding geometry and force progressions are described by function compositions of an inverse trigonometric function with the considered trigonometric function itself. If these functions are evaluated over several periods of the trigonometric function, a non-smooth oscillating curve occurs. Depending on the trigonometric function, these are often vividly described as zig-zag or sawtooth functions. The developed functions are applied to the Gossamer-1 design. The deployment geometry reveals a tendency that the loads are transferred along the catheti of the sail segments and therefore mainly along the boom axes. The load introduced by the spool deployment mechanism is described. By combining the deployment geometry with that load, a prediction of the deployment load progression is achieved. The mathematical description of the stowing and deployment geometry, as well as the forces inflicted by the mechanism provides an understanding of how exactly the membrane deploys and through which edges the deployment forces are transferred. The mathematical analysis also gives an impression of sensitive parameters that could be influenced by manufacturing tolerances or unsymmetrical deployment of the sail segments. While the mathematical model was applied on the design of

LDR structural experiment definition

Science.gov (United States)

Russell, Richard A.; Gates, Richard M.

1988-01-01

A study was performed to develop the definition of a structural flight experiment for a large precision segmented reflector that would utilize the Space Station. The objective of the study was to use the Large Deployable Reflector (LDR) baseline configuration for focusing on experiment definition activity which would identify the Space Station accommodation requirements and interface constraints. Results of the study defined three Space Station based experiments to demonstrate the technologies needed for an LDR type structure. The basic experiment configurations are the same as the JPL baseline except that the primary mirror truss is 10 meters in diameter instead of 20. The primary objectives of the first experiment are to construct the primary mirror support truss and to determine its structural and thermal characteristics. Addition of the optical bench, thermal shield and primary mirror segments and alignment of the optical components occur on the second experiment. The structure will then be moved to the payload pointing system for pointing, optical control and scientific optical measurement for the third experiment.

Using Quality Function Deployment To Improve Academic Advising Processes.

Science.gov (United States)

Barrows, Richard; Murray, Bruce

1997-01-01

Quality Function Deployment, a set of concepts and tools used in manufacturing engineering to link consumer needs with product design, can also improve academic advising systems and processes. The technique promotes structured, logical examination of students' advising needs and their relationship to advising system design, processes, methods,…

A Precision Measurement of the Neutron Spin Structure Functions Using a Polarized HE-3 Target

International Nuclear Information System (INIS)

Smith, T

2003-01-01

This thesis describes a precision measurement of the neutron spin dependent structure function, g 1 n (x). The measurement was made by the E154 collaboration at SLAC using a longitudinally polarized, 48.3 GeV electron beam, and a 3 He target polarized by spin exchange with optically pumped rubidium. A target polarization as high as 50% was achieved. The elements of the experiment which pertain to the polarized 3 He target will be described in detail in this thesis. To achieve a precision measurement, it has been necessary to minimize the systematic error from the uncertainty in the target parameters. All of the parameters of the target have been carefully measured, and the most important parameters of the target have been measured using multiple techniques. The polarization of the target was measured using nuclear magnetic resonance techniques, and has been calibrated using both proton NMR and by measuring the shift of the Rb Zeeman resonance frequency due to the 3 He polarization. The fraction of events which originated in the 3 He, as measured by the spectrometers, has been determined using a physical model of the target and the spectrometers. It was also measured during the experiment using a variable pressure 3 He reference cell in place of the polarized 3 He target. The spin dependent structure function g 1 n (z) was measured in the Bjorken x range of 0.014 2 of 5 (GeV/c) 2 . One of the primary motivations for this experiment was to test the Bjorken sum rule. Because the experiment had smaller statistical errors and a broader kinematic coverage than previous experiments, the behavior of the spin structure function g 1 n (x) could be studied in detail at low values of the Bjorken scaling variable x. It was found that g 1 n (x) has a strongly divergent behavior at low values of x, calling into question the methods commonly used to extrapolate the value of g 1 n (x) to low x. The precision of the measurement made by the E154 collaboration at SLAC puts a tighter

EDITORIAL Wireless sensor networks: design for real-life deployment and deployment experiences Wireless sensor networks: design for real-life deployment and deployment experiences

Science.gov (United States)

Gaura, Elena; Roedig, Utz; Brusey, James

2010-12-01

Wireless sensor networks (WSNs) are among the most promising technologies of the new millennium. The opportunities afforded by being able to program networks of small, lightweight, low-power, computation- and bandwidth-limited nodes have attracted a large community of researchers and developers. However, the unique set of capabilities offered by the technology produces an exciting but complex design space, which is often difficult to negotiate in an application context. Deploying sensing physical environments produces its own set of challenges, and can push systems into failure modes, thus revealing problems that can be difficult to discover or reproduce in simulation or the laboratory. Sustained efforts in the area of wireless networked sensing over the last 15 years have resulted in a large number of theoretical developments, substantial practical achievements, and a wealth of lessons for the future. It is clear that in order to bridge the gap between (on the one hand) visions of very large scale, autonomous, randomly deployed networks and (on the other) the actual performance of fielded systems, we need to view deployment as an essential component in the process of developing sensor networks: a process that includes hardware and software solutions that serve specific applications and end-user needs. Incorporating deployment into the design process reveals a new and different set of requirements and considerations, whose solutions require innovative thinking, multidisciplinary teams and strong involvement from end-user communities. This special feature uncovers and documents some of the hurdles encountered and solutions offered by experimental scientists when deploying and evaluating wireless sensor networks in situ, in a variety of well specified application scenarios. The papers specifically address issues of generic importance for WSN system designers: (i) data quality, (ii) communications availability and quality, (iii) alternative, low-energy sensing

Planning and Management of Technology Deployment Center

International Nuclear Information System (INIS)

Park, Jae Won; Joo, Po Kook; Kim, Jun Yeon and others

2005-08-01

The R and D contents are summarized as follows ; Models were set-up for transferring the developed technologies to the industry and managing technology deployment center to vitalize the commercialization and then the set-up model was tried to apply for transferring technologies for commercialization and to define interfaces between the R and D and industrial applications In this project, new products and processes were developed for promoting the commercialization. Infra-structures were firmly set-up for the venture company promotion and technology deployment developed during executing the proton Engineering frontier Project. Commercialization methodology connection with industrial companies were studied by outside specializing institute. Development of gem-stone coloring and new photo catalyst producing techniques are very high value-adding technologies, therefore, experimental and theoretical R and D were transacted simultaneously to obtain the originality of the technology. The theoretical R and D was committed to a specialist outside

A network architecture for precision formation flying using the IEEE 802.11 MAC Protocol

Science.gov (United States)

Clare, Loren P.; Gao, Jay L.; Jennings, Esther H.; Okino, Clayton

2005-01-01

Precision Formation Flying missions involve the tracking and maintenance of spacecraft in a desired geometric formation. The strong coupling of spacecraft in formation flying control requires inter-spacecraft communication to exchange information. In this paper, we present a network architecture that supports PFF control, from the initial random deployment phase to the final formation. We show that a suitable MAC layer for the application protocol is IEEE's 802.11 MAC protocol. IEEE 802.11 MAC has two modes of operations: DCF and PCF. We show that DCF is suitable for the initial deployment phase while switching to PCF when the spacecraft are in formation improves jitter and throughput. We also consider the effect of routing on protocol performance and suggest when it is profitable to turn off route discovery to achieve better network performance.

Design, deployment and performance of 4G-LTE networks a practical approach

CERN Document Server

ElNashar, Ayman; Sherif, Mahmoud

2014-01-01

This book provides an insight into the key practical aspects and best practice of 4G-LTE network design, performance, and deployment Design, Deployment and Performance of 4G-LTE Networks addresses the key practical aspects and best practice of 4G networks design, performance, and deployment. In addition, the book focuses on the end-to-end aspects of the LTE network architecture and different deployment scenarios of commercial LTE networks. It describes the air interface of LTE focusing on the access stratum protocol layers: PDCP, RLC, MAC, and Physical Layer. The air interface described in this book covers the concepts of LTE frame structure, downlink and uplink scheduling, and detailed illustrations of the data flow across the protocol layers. It describes the details of the optimization process including performance measurements and troubleshooting mechanisms in addition to demonstrating common issues and case studies based on actual field results. The book provides detailed performance analysis of key fe...

The impact of antecedent trauma exposure and mental health symptoms on the post-deployment mental health of Afghanistan-deployed Australian troops.

Science.gov (United States)

Searle, Amelia K; Van Hooff, Miranda; Lawrence-Wood, Ellie R; Grace, Blair S; Saccone, Elizabeth J; Davy, Carol P; Lorimer, Michelle; McFarlane, Alexander C

2017-10-01

Both traumatic deployment experiences and antecedent traumas increase personnel's risk of developing PTSD and depression. However, only cross-sectional studies have assessed whether antecedent trauma moderates stress reactions to deployment experiences. This study prospectively examines whether antecedent trauma moderates the association between deployment trauma and post-deployment PTSD and depressive symptoms after accounting for antecedent mental health problems, in a large Australian Defence Force (ADF) sample. In the ADF Middle East Area of Operations Prospective Study, currently-serving military personnel deployed to Afghanistan across 2010-2012 (n = 1122) completed self-reported measures at pre-deployment and post-deployment. Within multivariable regressions, associations between deployment trauma and PTSD and depressive symptoms at post-deployment were stronger for personnel with greater antecedent trauma. However, once adjusting for antecedent mental health problems, these significant interaction effects disappeared. Instead, deployment-related trauma and antecedent mental health problems showed direct associations with post-deployment mental health problems. Antecedent trauma was also indirectly associated with post-deployment mental health problems through antecedent mental health problems. Similar associations were seen with prior combat exposure as a moderator. Antecedent and deployment trauma were reported retrospectively. Self-reports may also suffer from social desirability bias, especially at pre-deployment. Our main effects results support the pervasive and cumulative negative effect of trauma on military personnel, regardless of its source. While antecedent trauma does not amplify personnel's psychological response to deployment trauma, it is indirectly associated with increased post-deployment mental health problems. Antecedent mental health should be considered within pre-deployment prevention programs, and deployment-trauma within post

Ultra-Lightweight Self-Deployable SMP Nanocomposite Sandwich for Habitat Applications, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Space deployable and rigidizable structures that are ultra-lightweight, and have gas barrier property, space durability, and high impact resistance are desirable to...

5-Beam ADCP Deployment Strategy Considerations

Science.gov (United States)

Moore, T.; Savidge, D. K.; Gargett, A.

2016-02-01

With the increasing availability of 5 beam ADCPs and expanding opportunities for their deployment within both observatory and dedicated process study settings, refinements in deployment strategies are needed.Measuring vertical velocities directly with a vertically oriented acoustic beam requires that the instrument be stably mounted and leveled within fractions of a degree. Leveled shallow water deployments to date have utilized divers to jet pipes into the sand for stability, manually mount the instruments on the pipes, and level them. Leveling has been guided by the deployed instrument's pitch and roll output, available in real-time because of the observatory settings in which the deployments occurred. To expand the range of feasible deployments to deeper, perhaps non-real-time capable settings, alternatives to diver deployment and leveling must be considered. To determine stability requirements, mooring motion (heading, pitch and roll) has been sampled at 1Hz by gimballed ADCPs at a range of instrument deployment depths, and in shrouded and unshrouded cages. Conditions under which ADCP cages resting on the bottom experience significant shifts in tilt, roll or heading are assessed using co-located wind and wave measurements. The accuracy of estimating vertical velocities using all five beams relative to a well leveled vertical single beam is assessed from archived high frequency five beam data, to explore whether easing the leveling requirement is feasible.

Precise documentation of well-structured programs

Energy Technology Data Exchange (ETDEWEB)

Parnas, D.L.; Madey, J.; Iglewski, M. [McMaster Univ., Hamilton, Ontario (Canada)

1997-11-01

This paper describes a new form of program documentation that is precise, systematic and readable. This documentation comprises a set of displays supplemented by a lexicon and an index. Each display presents a program fragment in such a way that its correctness can be examined without looking at any other display. Each display has three parts: (1) the specification of the program presented in the display, (2) the program itself, and (3) the specifications of programs invoked by this program. The displays are intended to be used by Software Engineers as a reference document during inspection and maintenance. This paper also introduces a specification technique that is a refinement of Mills functional approach to program documentation and verification; programs are specified and described in tabular form.

A Portable, Field-Deployable Analyzer for Isotopic Water Measurements

Science.gov (United States)

Berman, E. S.; Gupta, M.; Huang, Y. W.; Lacelle, D.; McKay, C. P.; Fortson, S.

2015-12-01

Water stable isotopes have for many years been used to study the hydrological cycle, catchment hydrology, and polar climate among other applications. Typically, discrete water samples are collected and transported to a laboratory for isotope analysis. Due to the expense and labor associated with such sampling, isotope studies have generally been limited in scope and time-resolution. Field sampling of water isotopes has been shown in recent years to provide dense data sets with the increased time resolution illuminating substantially greater short term variability than is generally observed during discrete sampling. A truly portable instrument also opens the possibility to utilize the instrument as a tool for identifying which water samples would be particularly interesting for further laboratory investigation. To make possible such field measurements of liquid water isotopes, Los Gatos Research has developed a miniaturized, field-deployable liquid water isotope analyzer. The prototype miniature liquid water isotope analyzer (mini-LWIA) uses LGR's patented Off-Axis ICOS (Integrated Cavity Output Spectroscopy) technology in a rugged, Pelican case housing for easy transport and field operations. The analyzer simultaneously measures both δ2H and δ18O from liquid water, with both manual and automatic water introduction options. The laboratory precision for δ2H is 0.6 ‰, and for δ18O is 0.3 ‰. The mini-LWIA was deployed in the high Arctic during the summer of 2015 at Inuvik in the Canadian Northwest Territories. Samples were collected from Sachs Harbor, on the southwest coast of Banks Island, including buried basal ice from the Lurentide Ice Sheet, some ice wedges, and other types of ground ice. Methodology and water analysis results from this extreme field deployment will be presented.

Regional Energy Deployment System (ReEDS)

Energy Technology Data Exchange (ETDEWEB)

Short, W.; Sullivan, P.; Mai, T.; Mowers, M.; Uriarte, C.; Blair, N.; Heimiller, D.; Martinez, A.

2011-12-01

The Regional Energy Deployment System (ReEDS) is a deterministic optimization model of the deployment of electric power generation technologies and transmission infrastructure throughout the contiguous United States into the future. The model, developed by the National Renewable Energy Laboratory's Strategic Energy Analysis Center, is designed to analyze the critical energy issues in the electric sector, especially with respect to potential energy policies, such as clean energy and renewable energy standards or carbon restrictions. ReEDS provides a detailed treatment of electricity-generating and electrical storage technologies and specifically addresses a variety of issues related to renewable energy technologies, including accessibility and cost of transmission, regional quality of renewable resources, seasonal and diurnal generation profiles, variability of wind and solar power, and the influence of variability on the reliability of the electrical grid. ReEDS addresses these issues through a highly discretized regional structure, explicit statistical treatment of the variability in wind and solar output over time, and consideration of ancillary services' requirements and costs.

Rapid deployment intrusion detection system

International Nuclear Information System (INIS)

Graham, R.H.

1997-01-01

A rapidly deployable security system is one that provides intrusion detection, assessment, communications, and annunciation capabilities; is easy to install and configure; can be rapidly deployed, and is reusable. A rapidly deployable intrusion detection system (RADIDS) has many potential applications within the DOE Complex: back-up protection for failed zones in a perimeter intrusion detection and assessment system, intrusion detection and assessment capabilities in temporary locations, protection of assets during Complex reconfiguration, and protection in hazardous locations, protection of assets during Complex reconfiguration, and protection in hazardous locations. Many DOE user-need documents have indicated an interest in a rapidly deployable intrusion detection system. The purpose of the RADIDS project is to design, develop, and implement such a system. 2 figs

Modeling EERE Deployment Programs

Energy Technology Data Exchange (ETDEWEB)

Cort, K. A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hostick, D. J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Belzer, D. B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Livingston, O. V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2007-11-01

This report compiles information and conclusions gathered as part of the “Modeling EERE Deployment Programs” project. The purpose of the project was to identify and characterize the modeling of deployment programs within the EERE Technology Development (TD) programs, address possible improvements to the modeling process, and note gaps in knowledge in which future research is needed.

Scoping study to expedite development of a field deployable and portable instrument for UF6 enrichment assay

OpenAIRE

Chan, CYG; Valentine, JD; Russo, RE

2017-01-01

The primary objective of the present study is to identity the most promising, viable technologies that are likely to culminate in an expedited development of the next-generation, field-deployable instrument for providing rapid, accurate, and precise enrichment assay of uranium hexafluoride (UF6). UF6 is typically involved, and is arguably the most important uranium compound, in uranium enrichment processes. As the first line of defense against proliferation, accurate analytical techniques t...

Precision two-photon spectroscopy of alkali elements

Indian Academy of Sciences (India)

2014-07-18

Jul 18, 2014 ... A review of various techniques adopted for measuring absolute frequencies of the atomic transitions and precision measurements of isotope shifts and hyperfine structures (HFS) is presented. Some of the recent works on precision measurements of HFS constants of 6 2 S 1 / 2 level of 39 K and 41 K, 9 2 ...

Dynamical modeling and free vibration analysis of spinning pipes conveying fluid with axial deployment

Science.gov (United States)

Liang, Feng; Yang, Xiao-Dong; Zhang, Wei; Qian, Ying-Jing

2018-03-01

In this paper, a dynamical model of simply-supported spinning pipes conveying fluid with axial deployment is proposed and the transverse free vibration and stability for such a doubly gyroscopic system involving time-dependent parameters are investigated. The partial differential equations of motion are derived by the extended Hamilton principle and then truncated by the Galerkin technique. The time-variant frequencies, mode shapes and responses to initial conditions are comprehensively investigated to reveal the dynamical essence of the system. It is indicated that the qualitative stability evolution of the system mainly depends on the effect of fluid-structure interaction (FSI), while the spinning motion will enhance the pipe rigidity and eliminate the buckling instability. The dynamical evolution of a retracting pipe is almost inverse to that of the deploying one. The pipe possesses different mode configurations of spatial curves as the pipe length increases and some modal and response characteristics of the present system are found rather distinct from those of deploying cantilevered structures.

Precision measurement with atom interferometry

International Nuclear Information System (INIS)

Wang Jin

2015-01-01

Development of atom interferometry and its application in precision measurement are reviewed in this paper. The principle, features and the implementation of atom interferometers are introduced, the recent progress of precision measurement with atom interferometry, including determination of gravitational constant and fine structure constant, measurement of gravity, gravity gradient and rotation, test of weak equivalence principle, proposal of gravitational wave detection, and measurement of quadratic Zeeman shift are reviewed in detail. Determination of gravitational redshift, new definition of kilogram, and measurement of weak force with atom interferometry are also briefly introduced. (topical review)

Precision Experiments at LEP

CERN Document Server

de Boer, Wim

2015-01-01

The Large Electron Positron Collider (LEP) established the Standard Model (SM) of particle physics with unprecedented precision, including all its radiative corrections. These led to predictions for the masses of the top quark and Higgs boson, which were beautifully confirmed later on. After these precision measurements the Nobel Prize in Physics was awarded in 1999 jointly to 't Hooft and Veltman "for elucidating the quantum structure of electroweak interactions in physics". Another hallmark of the LEP results were the precise measurements of the gauge coupling constants, which excluded unification of the forces within the SM, but allowed unification within the supersymmetric extension of the SM. This increased the interest in Supersymmetry (SUSY) and Grand Unified Theories, especially since the SM has no candidate for the elusive dark matter, while Supersymmetry provides an excellent candidate for dark matter. In addition, Supersymmetry removes the quadratic divergencies of the SM and {\\it predicts} the Hig...

A Precision Measurement of the Neutron Spin Structure Functions Using a Polarized HE-3 Target

Energy Technology Data Exchange (ETDEWEB)

Smith, T

2003-11-05

This thesis describes a precision measurement of the neutron spin dependent structure function, g{sub 1}{sup n}(x). The measurement was made by the E154 collaboration at SLAC using a longitudinally polarized, 48.3 GeV electron beam, and a {sup 3}He target polarized by spin exchange with optically pumped rubidium. A target polarization as high as 50% was achieved. The elements of the experiment which pertain to the polarized {sup 3}He target will be described in detail in this thesis. To achieve a precision measurement, it has been necessary to minimize the systematic error from the uncertainty in the target parameters. All of the parameters of the target have been carefully measured, and the most important parameters of the target have been measured using multiple techniques. The polarization of the target was measured using nuclear magnetic resonance techniques, and has been calibrated using both proton NMR and by measuring the shift of the Rb Zeeman resonance frequency due to the {sup 3}He polarization. The fraction of events which originated in the {sup 3}He, as measured by the spectrometers, has been determined using a physical model of the target and the spectrometers. It was also measured during the experiment using a variable pressure {sup 3}He reference cell in place of the polarized {sup 3}He target. The spin dependent structure function g{sub 1}{sup n}(z) was measured in the Bjorken x range of 0.014 < x < 0.7 with an average Q{sup 2} of 5 (GeV/c){sup 2}. One of the primary motivations for this experiment was to test the Bjorken sum rule. Because the experiment had smaller statistical errors and a broader kinematic coverage than previous experiments, the behavior of the spin structure function g{sub 1}{sup n}(x) could be studied in detail at low values of the Bjorken scaling variable x. It was found that g{sub 1}{sup n}(x) has a strongly divergent behavior at low values of x, calling into question the methods commonly used to extrapolate the value of g

Multi-functional hinge equipped with a magneto-rheological rotary damper for solar array deployment system

Science.gov (United States)

Wen, Mingfu; Yu, Miao; Fu, Jie; Wu, Zhengzhong

2015-02-01

This article describes the design and simulation of a novel multi-functional hinge equipped with a rotary magnetorheological damper for solar array deployment system, which is comprised of a hinge, an angular sensor, a positioning and locking mechanism and a rotary damper. In order to achieve the compact design in structure, some components were reused in different function modules. It's the first to use magnet-rheological fluid (MRF) to dissipate the energy in solar array deployment system. The main advantage in using MR rotary damper instead of a viscous fluid rotary damper is that the damping force of MR damper can be adjusted according to the external magnetic field environment excited. A mechanic model was built and the structure design was focused on the MR rotary damper, a damping force model of this damper is deduced based on hydromechanics with Bingham plastic constitutive model. A simulation of deployment motion was taken to validate the motion sequence of various components during the unfolding and locking process. It can be obtained that a constant damping coefficient can hardly balance the different performance of solar deployment system, then a simulation of the proposed deployment system equipped with rotary MR damper was carried out. According to the simulation, it can be obtained that the terminal velocity decreased by 75.81% and the deployment time decreased by 72.37% compared with a given constant damping coefficients. Therefore, the proposed new type of rotary damper can reach a compromise with different performance utilizing an on-off control strategy.

Optimization of Hydroacoustic Equipment Deployment at Foster Dam, 2013

Energy Technology Data Exchange (ETDEWEB)

Hughes, James S.; Johnson, Gary E.; Ploskey, Gene R.; Hennen, Matthew J.; Fischer, Eric S.; Zimmerman, Shon A.

2013-03-01

The goal of the study was to optimize performance of the fixed-location hydroacoustic systems at Foster Dam (FOS) by determining deployment and data acquisition methods that minimized structural, electrical, and acoustic interference. Optimization of the hydroacoustic systems will establish methodology for sampling by active acoustic methods during this year-long evaluation of juvenile salmonid passage at FOS.

A compact, large-range interferometer for precision measurement and inertial sensing

Science.gov (United States)

Cooper, S. J.; Collins, C. J.; Green, A. C.; Hoyland, D.; Speake, C. C.; Freise, A.; Mow-Lowry, C. M.

2018-05-01

We present a compact, fibre-coupled interferometer with high sensitivity and a large working range. We propose to use this interferometer as a readout mechanism for future inertial sensors, removing a major limiting noise source, and in precision positioning systems. The interferometer’s peak sensitivity is 2 × 10-{14} m \\sqrt{Hz-1} at 70 Hz and 7 × 10-{11} m \\sqrt{Hz-1} at 10 mHz. If deployed on a GS-13 geophone, the resulting inertial sensing output will be limited by the suspension thermal noise of the reference mass from 10 mHz to 2 Hz.

STRUCTURE OPTIMIZATION OF RESERVATION BY PRECISE QUADRATIC REGULARIZATION

Directory of Open Access Journals (Sweden)

KOSOLAP A. I.

2015-11-01

Full Text Available The problem of optimization of the structure of systems redundancy elements. Such problems arise in the design of complex systems. To improve the reliability of operation of such systems of its elements are duplicated. This increases system cost and improves its reliability. When optimizing these systems is maximized probability of failure of the entire system while limiting its cost or the cost is minimized for a given probability of failure-free operation. A mathematical model of the problem is a discrete backup multiextremal. To search for the global extremum of currently used methods of Lagrange multipliers, coordinate descent, dynamic programming, random search. These methods guarantee a just and local solutions are used in the backup tasks of small dimension. In the work for solving redundancy uses a new method for accurate quadratic regularization. This method allows you to convert the original discrete problem to the maximization of multi vector norm on a convex set. This means that the diversity of the tasks given to the problem of redundancy maximize vector norm on a convex set. To solve the problem, a reformed straightdual interior point methods. Currently, it is the best method for local optimization of nonlinear problems. Transformed the task includes a new auxiliary variable, which is determined by dichotomy. There have been numerous comparative numerical experiments in problems with the number of redundant subsystems to one hundred. These experiments confirm the effectiveness of the method of precise quadratic regularization for solving problems of redundancy.

Deployable Brake for Spacecraft

Science.gov (United States)

Rausch, J. R.; Maloney, J. W.

1987-01-01

Aerodynamic shield that could be opened and closed proposed. Report presents concepts for deployable aerodynamic brake. Brake used by spacecraft returning from high orbit to low orbit around Earth. Spacecraft makes grazing passes through atmosphere to slow down by drag of brake. Brake flexible shield made of woven metal or ceramic withstanding high temperatures created by air friction. Stored until needed, then deployed by set of struts.

Using Ground Radar Interferometry for Precise Determining of Deformation and Vertical Deflection of Structures

Science.gov (United States)

Talich, Milan

2017-12-01

The paper describes possibilities of the relatively new technics - ground based radar interferometry for precise determining of deformation of structures. Special focus on the vertical deflection of bridge structures and on the horizontal movements of high-rise buildings and structural objects is presented. The technology of ground based radar interferometry can be used in practice to the contactless determination of deformations of structures with accuracy up to 0.01 mm in real time. It is also possible in real time to capture oscillations of the object with a frequency up to 50 Hz. Deformations can be determined simultaneously in multiple places of the object, for example a bridge structure at points distributed on the bridge deck at intervals of one or more meters. This allows to obtain both overall and detailed information about the properties of the structure during the dynamic load and monitoring the impact of movements either individual vehicles or groups. In the case of high-rise buildings, it is possible to monitor the horizontal vibration of the whole object at its different height levels. It is possible to detect and determine the compound oscillations that occur in some types of buildings. Then prevent any damage or even disasters in these objects. In addition to the necessary theory basic principles of using radar interferometry for determining of deformation of structures are given. Practical examples of determining deformation of bridge structures, water towers reservoirs, factory chimneys and wind power plants are also given. The IBIS-S interferometric radar of the Italian IDS manufacturer was used for the measurements.

Precise colocalization of interacting structural and pigmentary elements generates extensive color pattern variation in Phelsuma lizards

Science.gov (United States)

2013-01-01

Background Color traits in animals play crucial roles in thermoregulation, photoprotection, camouflage, and visual communication, and are amenable to objective quantification and modeling. However, the extensive variation in non-melanic pigments and structural colors in squamate reptiles has been largely disregarded. Here, we used an integrated approach to investigate the morphological basis and physical mechanisms generating variation in color traits in tropical day geckos of the genus Phelsuma. Results Combining histology, optics, mass spectrometry, and UV and Raman spectroscopy, we found that the extensive variation in color patterns within and among Phelsuma species is generated by complex interactions between, on the one hand, chromatophores containing yellow/red pteridine pigments and, on the other hand, iridophores producing structural color by constructive interference of light with guanine nanocrystals. More specifically, we show that 1) the hue of the vivid dorsolateral skin is modulated both by variation in geometry of structural, highly ordered narrowband reflectors, and by the presence of yellow pigments, and 2) that the reflectivity of the white belly and of dorsolateral pigmentary red marks, is increased by underlying structural disorganized broadband reflectors. Most importantly, these interactions require precise colocalization of yellow and red chromatophores with different types of iridophores, characterized by ordered and disordered nanocrystals, respectively. We validated these results through numerical simulations combining pigmentary components with a multilayer interferential optical model. Finally, we show that melanophores form dark lateral patterns but do not significantly contribute to variation in blue/green or red coloration, and that changes in the pH or redox state of pigments provide yet another source of color variation in squamates. Conclusions Precisely colocalized interacting pigmentary and structural elements generate extensive

Deployment of the CMS software on the WLCG Grid

International Nuclear Information System (INIS)

Behrenhoff, W; Wissing, C; Kim, B; Blyweert, S; D'Hondt, J; Maes, J; Maes, M; Mulders, P Van; Villella, I; Vanelderen, L

2011-01-01

The CMS Experiment is taking high energy collision data at CERN. The computing infrastructure used to analyse the data is distributed round the world in a tiered structure. In order to use the 7 Tier-1 sites, the 50 Tier-2 sites and a still growing number of about 30 Tier-3 sites, the CMS software has to be available at those sites. Except for a very few sites the deployment and the removal of CMS software is managed centrally. Since the deployment team has no local accounts at the remote sites all installation jobs have to be sent via Grid jobs. Via a VOMS role the job has a high priority in the batch system and gains write privileges to the software area. Due to the lack of interactive access the installation jobs must be very robust against possible failures, in order not to leave a broken software installation. The CMS software is packaged in RPMs that are installed in the software area independent of the host OS. The apt-get tool is used to resolve package dependencies. This paper reports about the recent deployment experiences and the achieved performance.

Accommodating Thickness in Origami-Based Deployable Arrays

Science.gov (United States)

Zirbel, Shannon A.; Magleby, Spencer P.; Howell, Larry L.; Lang, Robert J.; Thomson, Mark W.; Sigel, Deborah A.; Walkemeyer, Phillip E.; Trease, Brian P.

2013-01-01

The purpose of this work is to create deployment systems with a large ratio of stowed-to-deployed diameter. Deployment from a compact form to a final flat state can be achieved through origami-inspired folding of panels. There are many models capable of this motion when folded in a material with negligible thickness; however, when the application requires the folding of thick, rigid panels, attention must be paid to the effect of material thickness not only on the final folded state, but also during the folding motion (i.e., the panels must not be required to flex to attain the final folded form). The objective is to develop new methods for deployment from a compact folded form to a large circular array (or other final form). This paper describes a mathematical model for modifying the pattern to accommodate material thickness in the context of the design, modeling, and testing of a deployable system inspired by an origami six-sided flasher model. The model is demonstrated in hardware as a 1/20th scale prototype of a deployable solar array for space applications. The resulting prototype has a ratio of stowed-to-deployed diameter of 9.2 (or 1.25 m deployed outer diameter to 0.136 m stowed outer diameter).

Supporting Knowledge Transfer in IS Deployment Projects

Science.gov (United States)

Schönström, Mikael

To deploy new information systems is an expensive and complex task, and does seldom result in successful usage where the system adds strategic value to the firm (e.g. Sharma et al. 2003). It has been argued that innovation diffusion is a knowledge integration problem (Newell et al. 2000). Knowledge about business processes, deployment processes, information systems and technology are needed in a large-scale deployment of a corporate IS. These deployments can therefore to a large extent be argued to be a knowledge management (KM) problem. An effective deployment requires that knowledge about the system is effectively transferred to the target organization (Ko et al. 2005).

Nanomaterials for Cancer Precision Medicine.

Science.gov (United States)

Wang, Yilong; Sun, Shuyang; Zhang, Zhiyuan; Shi, Donglu

2018-04-01

Medical science has recently advanced to the point where diagnosis and therapeutics can be carried out with high precision, even at the molecular level. A new field of "precision medicine" has consequently emerged with specific clinical implications and challenges that can be well-addressed by newly developed nanomaterials. Here, a nanoscience approach to precision medicine is provided, with a focus on cancer therapy, based on a new concept of "molecularly-defined cancers." "Next-generation sequencing" is introduced to identify the oncogene that is responsible for a class of cancers. This new approach is fundamentally different from all conventional cancer therapies that rely on diagnosis of the anatomic origins where the tumors are found. To treat cancers at molecular level, a recently developed "microRNA replacement therapy" is applied, utilizing nanocarriers, in order to regulate the driver oncogene, which is the core of cancer precision therapeutics. Furthermore, the outcome of the nanomediated oncogenic regulation has to be accurately assessed by the genetically characterized, patient-derived xenograft models. Cancer therapy in this fashion is a quintessential example of precision medicine, presenting many challenges to the materials communities with new issues in structural design, surface functionalization, gene/drug storage and delivery, cell targeting, and medical imaging. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

[Precision nutrition in the era of precision medicine].

Science.gov (United States)

Chen, P Z; Wang, H

2016-12-06

Precision medicine has been increasingly incorporated into clinical practice and is enabling a new era for disease prevention and treatment. As an important constituent of precision medicine, precision nutrition has also been drawing more attention during physical examinations. The main aim of precision nutrition is to provide safe and efficient intervention methods for disease treatment and management, through fully considering the genetics, lifestyle (dietary, exercise and lifestyle choices), metabolic status, gut microbiota and physiological status (nutrient level and disease status) of individuals. Three major components should be considered in precision nutrition, including individual criteria for sufficient nutritional status, biomarker monitoring or techniques for nutrient detection and the applicable therapeutic or intervention methods. It was suggested that, in clinical practice, many inherited and chronic metabolic diseases might be prevented or managed through precision nutritional intervention. For generally healthy populations, because lifestyles, dietary factors, genetic factors and environmental exposures vary among individuals, precision nutrition is warranted to improve their physical activity and reduce disease risks. In summary, research and practice is leading toward precision nutrition becoming an integral constituent of clinical nutrition and disease prevention in the era of precision medicine.

Hepsoft - an approach for up to date multi-platform deployment of HEP specific software

International Nuclear Information System (INIS)

Roiser, S

2011-01-01

LHC experiments are depending on a rich palette of software components to build their specific applications. These underlying software components include the ROOT analysis framework, the Geant4 simulation toolkit, Monte Carlo generators, grid middle-ware, graphics libraries, scripting languages, databases, tools, etc. which are provided centrally in up to date versions on multiple platforms (Linux, Mac, Windows). Until recently this set of packages has been tested and released in a tree like structure as a consistent set of versions across operating systems, architectures and compilers for LHC experiments only. Because of the tree like deployment these releases were only usable in connection with a configuration management tool which provided the proper build and run-time environments and was hindering other parties outside LHC from easily using this palette of packages. In a new approach the releases will be grouped in 'flat structure' such that interested parties can start using it without configuration management, retaining all the above mentioned advantages. In addition to an increased usability the software shall also be distributed via system provided package deployment systems (rpm, apt, etc.). The approach of software deployment is following the ideas of providing a wide range of HEP specific software packages and tools in a coherent, up to date and modular way on multiple platforms. The target audience for such software deployments are individual developers or smaller development groups / experiments who don't have the resources to maintain this kind of infrastructure. This new software deployment strategy has already been successfully implemented for groups at CERN.

Singular point analysis during rail deployment into vacuum vessel for ITER blanket maintenance

International Nuclear Information System (INIS)

Kakudate, Satoshi; Shibanuma, Kiyoshi

2007-05-01

Remote maintenance of the ITER blanket composed of about 400 modules in the vessel is required by a maintenance robot due to high gamma radiation of ∼500Gy/h in the vessel. A concept of rail-mounted vehicle manipulator system has been developed to apply to the maintenance of the ITER blanket. The most critical issue of the vehicle manipulator system is the feasibility of the deployment of the articulated rail composed of eight rail links into the donut-shaped vessel without any driving mechanism in the rail. To solve this issue, a new driving mechanism and procedure for the rail deployment has been proposed, taking account of a repeated operation of the multi-rail links deployed in the same kinematical manner. The new driving mechanism, which is deferent from those of a usual 'articulated arm' equipped with actuator in the every joint for movement, is composed of three mechanisms. To assess the feasibility of the kinematics of the articulated rail for rail deployment, a kinematical model composed of three rail links related to a cycle of the repeated operation for rail deployment was considered. The determinant det J' of the Jacobian matrix J' was solved so as to estimate the existence of a singular point of the transformation during rail deployment. As a result, it is found that there is a singular point due to det J'=0. To avoid the singular point of the rail links, a new location of the second driving mechanism and the related rail deployment procedure are proposed. As a result of the rail deployment test based on the new proposal using a full-scale vehicle manipulator system, the respective rail links have been successfully deployed within 6 h less than the target of 8 h in the same manner of the repeated operation under a synchronized cooperation among the three driving mechanisms. It is therefore concluded that the feasibility of the rail deployment of the articulated rail composed of simple structures without any driving mechanism has been demonstrated

Associations of contextual risk and protective factors with fathers’ parenting practices in the post-deployment environment

Science.gov (United States)

Davis, Laurel; Hanson, Sheila K.; Zamir, Osnat; Gewirtz, Abigail H.; DeGarmo, David S.

2015-01-01

Deployment separation and reunifications are salient contexts that directly impact effective family functioning and parenting for military fathers. Yet, we know very little about determinants of post-deployed father involvement and effective parenting. The present study examined hypothesized risk and protective factors of observed parenting for 282 post-deployed fathers who served in the Army National Guard/Reserves. Pre-intervention data were employed from fathers participating in the After Deployment, Adaptive Parenting Tools (ADAPT) randomized control trial. Parenting practices were obtained from direct observation of father-child interaction and included measures of problem solving, harsh discipline, positive involvement, encouragement, and monitoring. Risk factors included combat exposure, negative life events, months deployed, and PTSD symptoms. Protective factors included education, income, dyadic adjustment, and social support. Results of a structural equation model predicting an effective parenting construct indicated that months deployed, income, and father age were most related to observed parenting, explaining 16% of the variance. We are aware of no other study utilizing direct parent-child observations of father’s parenting skills following overseas deployment. Implications for practice and preventive intervention are discussed. PMID:26213794

The effect of military deployment on mental health

DEFF Research Database (Denmark)

Lyk-Jensen, Stéphanie; Weatherall, Cecilie Dohlmann; W. Jepsen, Peter

for the non-deployed eligible men, and our results hold to various robustness checks. Our administrative records provide objective measures of mental health service use in the form of psychiatric diagnoses and purchase of mental health-related medication. The very rich data makes it possible to control......In this paper we estimate the causal effect of military deployment on soldiers’ mental health. To handle the selection bias problem, we use longitudinal data for deployed and non-deployed eligible men in a difference-in-differences setting. Using pair-wise matching, we impute deployment dates...... for important variables like intelligence tests and family background. We find significant adverse effects of military deployment on soldiers’ mental health service use. Highlights: - Causal effect of military deployment on soldiers’ use of mental health service - Using a difference-in-differences approach...

Computer Security: How to succeed in software deployment

CERN Multimedia

Computer Security Team

2014-01-01

The summer student period has ended and we would like to congratulate all those who successfully accomplished their project! In particular, well done to those who managed to develop and deploy sophisticated web applications in the short summer season. Unfortunately, not all web applications made the final cut, moved into production and became visible on the Internet. We had to reject some... let me explain why.   Making a web application visible on the Internet requires an opening in the CERN outer perimeter firewall. Such a request is usually made through the CERN WebReq web interface. As standard procedure, the CERN Computer Security team reviews every request and performs a security assessment. This is where you, your supervisee and the Computer Security team all start to get frustrated. Many summer students delivered awesome web applications with great new functions and a good “look and feel” following precise use cases, using modern web technologies, dashboards, integr...

The study of high precision neutron moisture gauge

International Nuclear Information System (INIS)

Liu Shengkang; Bao Guanxiong; Sang Hai; Zhu Yuzhen

1993-01-01

The principle, structure and calibration experiment of the high precision neutron moisture gauge (insertion type) are described. The gauge has been appraised. The precision of the measuring moisture of coke is lower than 0.5%, and the range of the measuring moisture is 2%-12%. The economic benefit of the gauge application is good

What Is Trust? Ethics and Risk Governance in Precision Medicine and Predictive Analytics.

Science.gov (United States)

Adjekum, Afua; Ienca, Marcello; Vayena, Effy

2017-12-01

Trust is a ubiquitous term used in emerging technology (e.g., Big Data, precision medicine), innovation policy, and governance literatures in particular. But what exactly is trust? Even though trust is considered a critical requirement for the successful deployment of precision medicine initiatives, nonetheless, there is a need for further conceptualization with regard to what qualifies as trust, and what factors might establish and sustain trust in precision medicine, predictive analytics, and large-scale biology. These new fields of 21st century medicine and health often deal with the "futures" and hence, trust gains a temporal and ever-present quality for both the present and the futures anticipated by new technologies and predictive analytics. We address these conceptual gaps that have important practical implications in the way we govern risk and unknowns associated with emerging technologies in biology, medicine, and health broadly. We provide an in-depth conceptual analysis and an operative definition of trust dynamics in precision medicine. In addition, we identify three main types of "trust facilitators": (1) technical, (2) ethical, and (3) institutional. This three-dimensional framework on trust is necessary to building and maintaining trust in 21st century knowledge-based innovations that governments and publics invest for progressive societal change, development, and sustainable prosperity. Importantly, we analyze, identify, and deliberate on the dimensions of precision medicine and large-scale biology that have carved out trust as a pertinent tool to its success. Moving forward, we propose a "points to consider" on how best to enhance trust in precision medicine and predictive analytics.

Deployment Effects of Marin Renewable Energy Technologies

Energy Technology Data Exchange (ETDEWEB)

Brian Polagye; Mirko Previsic

2010-06-17

Given proper care in siting, design, deployment, operation and maintenance, marine and hydrokinetic technologies could become one of the more environmentally benign sources of electricity generation. In order to accelerate the adoption of these emerging hydrokinetic and marine energy technologies, navigational and environmental concerns must be identified and addressed. All developing hydrokinetic projects involve a wide variety of stakeholders. One of the key issues that site developers face as they engage with this range of stakeholders is that many of the possible conflicts (e.g., shipping and fishing) and environmental issues are not well-understood, due to a lack of technical certainty. In September 2008, re vision consulting, LLC was selected by the Department of Energy (DoE) to apply a scenario-based approach to the emerging wave and tidal technology sectors in order to evaluate the impact of these technologies on the marine environment and potentially conflicting uses. The project’s scope of work includes the establishment of baseline scenarios for wave and tidal power conversion at potential future deployment sites. The scenarios will capture variations in technical approaches and deployment scales to properly identify and characterize environmental impacts and navigational effects. The goal of the project is to provide all stakeholders with an improved understanding of the potential effects of these emerging technologies and focus all stakeholders onto the critical issues that need to be addressed. This groundwork will also help in streamlining siting and associated permitting processes, which are considered key hurdles for the industry’s development in the U.S. today. Re vision is coordinating its efforts with two other project teams funded by DoE which are focused on regulatory and navigational issues. The results of this study are structured into three reports: 1. Wave power scenario description 2. Tidal power scenario description 3. Framework for

High Precision Continuous and Real-Time Measurement of Atmospheric Oxygen Using Cavity Ring-Down Spectroscopy.

Science.gov (United States)

Kim-Hak, D.; Hoffnagle, J.; Rella, C.; Sun, M.

2016-12-01

Oxygen is a major and vital component of the Earth atmosphere representing about 21% of its composition. It is consumed or produced through biochemical processes such as combustion, respiration, and photosynthesis. Although atmospheric oxygen is not a greenhouse gas, it can be used as a top-down constraint on the carbon cycle. The variation observations of oxygen in the atmosphere are very small, in the order of the few ppm's. This presents the main technical challenge for measurement as a very high level of precision is required and only few methods including mass spectrometry, fuel cell, and paramagnetic are capable of overcoming it. Here we present new developments of a high-precision gas analyzer that utilizes the technique of Cavity Ring-Down Spectroscopy to measure oxygen concentration and oxygen isotope. Its compact and ruggedness design combined with high precision and long-term stability allows the user to deploy the instrument in the field for continuous monitoring of atmospheric oxygen level. Measurements have a 1-σ 5-minute averaging precision of 1-2 ppm for O2 over a dynamic range of 0-20%. We will present supplemental data acquired from our 10m tower measurements in Santa Clara, CA.

CoalFleet for tomorrow. An industry initiative to accelerate the deployment of advanced coal-based generation plants

Energy Technology Data Exchange (ETDEWEB)

Parkes, J.; Holt, N.; Phillips, J. [Electric Power Research Institute (United States)

2006-07-01

The industry initiative 'CoalFleet for tomorrow' was launched in November 2004 to accelerate the deployment and commercialization of clean, efficient, advanced coal power systems. This paper discusses the structure of CoalFleet and its strategy for reducing the cost, leadtime and risk of deploying advanced coal technologies such as combined-cycle power plants. 6 figs.

Precise positioning with current multi-constellation Global Navigation Satellite Systems: GPS, GLONASS, Galileo and BeiDou.

Science.gov (United States)

Li, Xingxing; Zhang, Xiaohong; Ren, Xiaodong; Fritsche, Mathias; Wickert, Jens; Schuh, Harald

2015-02-09

The world of satellite navigation is undergoing dramatic changes with the rapid development of multi-constellation Global Navigation Satellite Systems (GNSSs). At the moment more than 70 satellites are already in view, and about 120 satellites will be available once all four systems (BeiDou + Galileo + GLONASS + GPS) are fully deployed in the next few years. This will bring great opportunities and challenges for both scientific and engineering applications. In this paper we develop a four-system positioning model to make full use of all available observations from different GNSSs. The significant improvement of satellite visibility, spatial geometry, dilution of precision, convergence, accuracy, continuity and reliability that a combining utilization of multi-GNSS brings to precise positioning are carefully analyzed and evaluated, especially in constrained environments.

Eigenspaces of networks reveal the overlapping and hierarchical community structure more precisely

International Nuclear Information System (INIS)

Ma, Xiaoke; Gao, Lin; Yong, Xuerong

2010-01-01

Identifying community structure is fundamental for revealing the structure–functionality relationship in complex networks, and spectral algorithms have been shown to be powerful for this purpose. In a traditional spectral algorithm, each vertex of a network is embedded into a spectral space by making use of the eigenvectors of the adjacency matrix or Laplacian matrix of the graph. In this paper, a novel spectral approach for revealing the overlapping and hierarchical community structure of complex networks is proposed by not only using the eigenvalues and eigenvectors but also the properties of eigenspaces of the networks involved. This gives us a better characterization of community. We first show that the communicability between a pair of vertices can be rewritten in term of eigenspaces of a network. An agglomerative clustering algorithm is then presented to discover the hierarchical communities using the communicability matrix. Finally, these overlapping vertices are discovered with the corresponding eigenspaces, based on the fact that the vertices more densely connected amongst one another are more likely to be linked through short cycles. Compared with the traditional spectral algorithms, our algorithm can identify both the overlapping and hierarchical community without increasing the time complexity O(n 3 ), where n is the size of the network. Furthermore, our algorithm can also distinguish the overlapping vertices from bridges. The method is tested by applying it to some computer-generated and real-world networks. The experimental results indicate that our algorithm can reveal community structure more precisely than the traditional spectral approaches

Security Support in Continuous Deployment Pipeline

DEFF Research Database (Denmark)

Ullah, Faheem; Raft, Adam Johannes; Shahin, Mojtaba

2017-01-01

Continuous Deployment (CD) has emerged as a new practice in the software industry to continuously and automatically deploy software changes into production. Continuous Deployment Pipeline (CDP) supports CD practice by transferring the changes from the repository to production. Since most of the CDP...... penetration tools. Our findings indicate that the applied tactics improve the security of the major components (i.e., repository, continuous integration server, main server) of a CDP by controlling access to the components and establishing secure connections....

Advanced OS deployment system

OpenAIRE

Galiano Molina, Sebastián

2007-01-01

The main project’s objective is to design and build an OS deployment system taking advantage of the Linux OS and the Open Source community developments. This means to use existing technologies that modularize the system. With this philosophy in mind, the number of developed code lines within the project is keeping as small as possible. As REMBO, the OS deployment system to develop has to be transparent to the user. This means a system with a friendly user interface and no te...

Renewable Energy: Policy Considerations for Deploying Renewables

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-07-01

This information paper accompanies the IEA publication Deploying Renewables 2011: Best and Future Policy Practice (IEA, 2011a). It provides more detailed data and analysis on policies for Deploying Renewables, and is intended to complement the main publication. It provides an account of the strategic drivers underpinning renewable energy (RE) technology deployment (energy security, economic development and environment protection) and assesses RE technologies with respect to these drivers, including an estimate of GHG emissions reductions due to RE technologies. The paper also explores the different barriers to deploying renewables at a given stage of market maturity and discusses what tools policy makers can avail of to succeed in removing deployment barriers. An additional topical highlight explores the challenges associated with accelerating the diffusion of RE technologies in developing countries.

Collaborative Genomics Study Advances Precision Oncology

Science.gov (United States)

A collaborative study conducted by two Office of Cancer Genomics (OCG) initiatives highlights the importance of integrating structural and functional genomics programs to improve cancer therapies, and more specifically, contribute to precision oncology treatments for children.

Deployment Health Surveillance

National Research Council Canada - National Science Library

DeNicola, Anthony D

2004-01-01

.... Gulf War health questions have resulted in controversy over potentially hazardous exposures during the deployment, the possibility of adverse affects from preventive health measures, and the role...

Rapid whole genome sequencing and precision neonatology.

Science.gov (United States)

Petrikin, Joshua E; Willig, Laurel K; Smith, Laurie D; Kingsmore, Stephen F

2015-12-01

Traditionally, genetic testing has been too slow or perceived to be impractical to initial management of the critically ill neonate. Technological advances have led to the ability to sequence and interpret the entire genome of a neonate in as little as 26 h. As the cost and speed of testing decreases, the utility of whole genome sequencing (WGS) of neonates for acute and latent genetic illness increases. Analyzing the entire genome allows for concomitant evaluation of the currently identified 5588 single gene diseases. When applied to a select population of ill infants in a level IV neonatal intensive care unit, WGS yielded a diagnosis of a causative genetic disease in 57% of patients. These diagnoses may lead to clinical management changes ranging from transition to palliative care for uniformly lethal conditions for alteration or initiation of medical or surgical therapy to improve outcomes in others. Thus, institution of 2-day WGS at time of acute presentation opens the possibility of early implementation of precision medicine. This implementation may create opportunities for early interventional, frequently novel or off-label therapies that may alter disease trajectory in infants with what would otherwise be fatal disease. Widespread deployment of rapid WGS and precision medicine will raise ethical issues pertaining to interpretation of variants of unknown significance, discovery of incidental findings related to adult onset conditions and carrier status, and implementation of medical therapies for which little is known in terms of risks and benefits. Despite these challenges, precision neonatology has significant potential both to decrease infant mortality related to genetic diseases with onset in newborns and to facilitate parental decision making regarding transition to palliative care. Copyright © 2015 Elsevier Inc. All rights reserved.

Multi-scale structural community organisation of the human genome.

Science.gov (United States)

Boulos, Rasha E; Tremblay, Nicolas; Arneodo, Alain; Borgnat, Pierre; Audit, Benjamin

2017-04-11

Structural interaction frequency matrices between all genome loci are now experimentally achievable thanks to high-throughput chromosome conformation capture technologies. This ensues a new methodological challenge for computational biology which consists in objectively extracting from these data the structural motifs characteristic of genome organisation. We deployed the fast multi-scale community mining algorithm based on spectral graph wavelets to characterise the networks of intra-chromosomal interactions in human cell lines. We observed that there exist structural domains of all sizes up to chromosome length and demonstrated that the set of structural communities forms a hierarchy of chromosome segments. Hence, at all scales, chromosome folding predominantly involves interactions between neighbouring sites rather than the formation of links between distant loci. Multi-scale structural decomposition of human chromosomes provides an original framework to question structural organisation and its relationship to functional regulation across the scales. By construction the proposed methodology is independent of the precise assembly of the reference genome and is thus directly applicable to genomes whose assembly is not fully determined.

Precisely Tailored DNA Nanostructures and their Theranostic Applications.

Science.gov (United States)

Zhu, Bing; Wang, Lihua; Li, Jiang; Fan, Chunhai

2017-12-01

A critical challenge in nanotechnology is the limited precision and controllability of the structural parameters, which brings about concerns in uniformity, reproducibility and performance. Self-assembled DNA nanostructures, as a newly emerged type of nano-biomaterials, possess low-nanometer precision, excellent programmability and addressability. They can precisely arrange various molecules and materials to form spatially ordered complex, resulting in unambiguous physical or chemical properties. Because of these, DNA nanostructures have shown great promise in numerous biomedical theranostic applications. In this account, we briefly review the history and advances on construction of DNA nanoarchitectures and superstructures with accurate structural parameters. We focus on recent progress in exploiting these DNA nanostructures as platforms for quantitative biosensing, intracellular diagnosis, imaging, and smart drug delivery. We also discuss key challenges in practical applications. © 2017 The Chemical Society of Japan & Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Early identification of posttraumatic stress following military deployment

DEFF Research Database (Denmark)

Karstoft, Karen-Inge; Statnikov, Alexander; Andersen, Søren B

2015-01-01

BACKGROUND: Pre-deployment identification of soldiers at risk for long-term posttraumatic stress psychopathology after home coming is important to guide decisions about deployment. Early post-deployment identification can direct early interventions to those in need and thereby prevents...... the development of chronic psychopathology. Both hold significant public health benefits given large numbers of deployed soldiers, but has so far not been achieved. Here, we aim to assess the potential for pre- and early post-deployment prediction of resilience or posttraumatic stress development in soldiers...... by application of machine learning (ML) methods. METHODS: ML feature selection and prediction algorithms were applied to a prospective cohort of 561 Danish soldiers deployed to Afghanistan in 2009 to identify unique risk indicators and forecast long-term posttraumatic stress responses. RESULTS: Robust pre...

Precision validation of MIPAS-Envisat products

Directory of Open Access Journals (Sweden)

C. Piccolo

2007-01-01

Full Text Available This paper discusses the variation and validation of the precision, or estimated random error, associated with the ESA Level 2 products from the Michelson Interferometer for Passive Atmospheric Sounding (MIPAS. This quantity represents the propagation of the radiometric noise from the spectra through the retrieval process into the Level 2 profile values. The noise itself varies with time, steadily rising between ice decontamination events, but the Level 2 precision has a greater variation due to the atmospheric temperature which controls the total radiance received. Hence, for all species, the precision varies latitudinally/seasonally with temperature, with a small superimposed temporal structure determined by the degree of ice contamination on the detectors. The precision validation involves comparing two MIPAS retrievals at the intersections of ascending/descending orbits. For 5 days per month of full resolution MIPAS operation, the standard deviation of the matching profile pairs is computed and compared with the precision given in the MIPAS Level 2 data, except for NO2 since it has a large diurnal variation between ascending/descending intersections. Even taking into account the propagation of the pressure-temperature retrieval errors into the VMR retrieval, the standard deviation of the matching pairs is usually a factor 1–2 larger than the precision. This is thought to be due to effects such as horizontal inhomogeneity of the atmosphere and instability of the retrieval.

Computational design analysis for deployment of cardiovascular stents

International Nuclear Information System (INIS)

Tammareddi, Sriram; Sun Guangyong; Li Qing

2010-01-01

Cardiovascular disease has become a major global healthcare problem. As one of the relatively new medical devices, stents offer a minimally-invasive surgical strategy to improve the quality of life for numerous cardiovascular disease patients. One of the key associative issues has been to understand the effect of stent structures on its deployment behaviour. This paper aims to develop a computational model for exploring the biomechanical responses to the change in stent geometrical parameters, namely the strut thickness and cross-link width of the Palmaz-Schatz stent. Explicit 3D dynamic finite element analysis was carried out to explore the sensitivity of these geometrical parameters on deployment performance, such as dog-boning, fore-shortening, and stent deformation over the load cycle. It has been found that an increase in stent thickness causes a sizeable rise in the load required to deform the stent to its target diameter, whilst reducing maximum dog-boning in the stent. An increase in the cross-link width showed that no change in the load is required to deform the stent to its target diameter, and there is no apparent correlation with dog-boning but an increased fore-shortening with increasing cross-link width. The computational modelling and analysis presented herein proves an effective way to refine or optimise the design of stent structures.

Crustal structure and fault geometry of the 2010 Haiti earthquake from temporary seismometer deployments

Science.gov (United States)

Douilly, Roby; Haase, Jennifer S.; Ellsworth, William L.; Bouin, Marie‐Paule; Calais, Eric; Symithe, Steeve J.; Armbruster, John G.; Mercier de Lépinay, Bernard; Deschamps, Anne; Mildor, Saint‐Louis; Meremonte, Mark E.; Hough, Susan E.

2013-01-01

Haiti has been the locus of a number of large and damaging historical earthquakes. The recent 12 January 2010 Mw 7.0 earthquake affected cities that were largely unprepared, which resulted in tremendous losses. It was initially assumed that the earthquake ruptured the Enriquillo Plantain Garden fault (EPGF), a major active structure in southern Haiti, known from geodetic measurements and its geomorphic expression to be capable of producing M 7 or larger earthquakes. Global Positioning Systems (GPS) and Interferometric Synthetic Aperture Radar (InSAR) data, however, showed that the event ruptured a previously unmapped fault, the Léogâne fault, a north‐dipping oblique transpressional fault located immediately north of the EPGF. Following the earthquake, several groups installed temporary seismic stations to record aftershocks, including ocean‐bottom seismometers on either side of the EPGF. We use data from the complete set of stations deployed after the event, on land and offshore, to relocate all aftershocks from 10 February to 24 June 2010, determine a 1D regional crustal velocity model, and calculate focal mechanisms. The aftershock locations from the combined dataset clearly delineate the Léogâne fault, with a geometry close to that inferred from geodetic data. Its strike and dip closely agree with the global centroid moment tensor solution of the mainshock but with a steeper dip than inferred from previous finite fault inversions. The aftershocks also delineate a structure with shallower southward dip offshore and to the west of the rupture zone, which could indicate triggered seismicity on the offshore Trois Baies reverse fault. We use first‐motion focal mechanisms to clarify the relationship of the fault geometry to the triggered aftershocks.

Deploying Renewables - Best and Future Policy Practice

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-11-23

The global energy system faces urgent challenges. Concerns about energy security are growing, as highlighted by the recent political turmoil in Northern Africa and the nuclear incident in Fukushima. At the same time, the need to respond to climate change is more critical than ever. Against this background, many governments have increased efforts to promote deployment of renewable energy -- low-carbon sources that can strengthen energy security. This has stimulated unprecedented rise in deployment, and renewables are now the fastest growing sector of the energy mix. This 'coming of age' of renewable energy also brings challenges. Growth is focused on a few of the available technologies, and rapid deployment is confined to a relatively small number of countries. In more advanced markets, managing support costs and system integration of large shares of renewable energy in a time of economic weakness and budget austerity has sparked vigorous political debate. The IEA's new report, Deploying Renewables 2011: Best and Future Policy Practice: - Provides a comprehensive review and analysis of renewable energy policy and market trends; - Analyses in detail the dynamics of deployment and provides best-practice policy principles for different stages of market maturity; - Assesses the impact and cost-effectiveness of support policies using new methodological tools and indicators; - Investigates the strategic reasons underpinning the pursuit of RE deployment by different countries and the prospects for globalisation of RE. This new book builds on and extends a 2008 IEA publication, drawing on recent policy and deployment experience world-wide. It provides guidance for policy makers and other stakeholders to avoid past mistakes, overcome new challenges and reap the benefits of deploying renewables -- today and tomorrow.

Modeling EERE Deployment Programs

Energy Technology Data Exchange (ETDEWEB)

Cort, Katherine A.; Hostick, Donna J.; Belzer, David B.; Livingston, Olga V.

2007-11-08

The purpose of this report is to compile information and conclusions gathered as part of three separate tasks undertaken as part of the overall project, “Modeling EERE Deployment Programs,” sponsored by the Planning, Analysis, and Evaluation office within the Department of Energy’s Office of Energy Efficiency and Renewable Energy (EERE). The purpose of the project was to identify and characterize the modeling of deployment programs within the EERE Technology Development (TD) programs, address improvements to modeling in the near term, and note gaps in knowledge where future research is needed.

Remote Systems Design & Deployment

Energy Technology Data Exchange (ETDEWEB)

Bailey, Sharon A.; Baker, Carl P.; Valdez, Patrick LJ

2009-08-28

The Pacific Northwest National Laboratory (PNNL) was tasked by Washington River Protection Solutions, LLC (WRPS) to provide information and lessons learned relating to the design, development and deployment of remote systems, particularly remote arm/manipulator systems. This report reflects PNNL’s experience with remote systems and lays out the most important activities that need to be completed to successfully design, build, deploy and operate remote systems in radioactive and chemically contaminated environments. It also contains lessons learned from PNNL’s work experiences, and the work of others in the national laboratory complex.

Deployment Health Surveillance

National Research Council Canada - National Science Library

DeNicola, Anthony D

2004-01-01

... of stress in causing chronic illness. The lack of comprehensive deployment health surveillance has made it difficult to determine possible causes of adverse health effects reported by Gulf War veterans...

Deployment-related risk factors of low back pain

DEFF Research Database (Denmark)

Nissen, Lars Ravnborg; Marott, Jacob Louis; Gyntelberg, Finn

2014-01-01

Where much is known about the consequences of spinal and low back pain (LBP) during military deployments, there is lesser knowledge of risk factors for LBP among the deployed forces. The objective of this study was to identify deployment-related exposures associated with LBP. The study was a ques...... their subordinates and involve medical personnel, especially deployed physiotherapists, by giving advice to soldiers of different military occupational specialties on how to optimize ergonomics at work....

Family Reintegration Following Guard Deployment

Science.gov (United States)

2010-09-20

Somalia Peacekeepers. Journal of Consulting and Clinical Psychology, 72(5), 909-913. Haas DM . Pazdernik LA. Olsen CH. A cross-sectional survey of the...relationship between partner deployment and stress in pregnancy during wartime. Haas DM . Pazdernik LA. Partner deployment and stress in pregnant...Identify 3-5 key words relating to the proposal. (Required) I used MESH Headings instead of the CRISP Thesaurus for key

Evaluating the precision of passive sampling methods using ...

Science.gov (United States)

To assess these models, four different thicknesses of low-density polyethylene (LDPE) passive samplers were co-deployed for 28 days in the water column at three sites in New Bedford Harbor, MA, USA. Each sampler was pre-loaded with six PCB performance reference compounds (PRCs) to assess equilibrium status, such that the percent of PRC lost would range depending on PRC and LDPE thickness. These data allow subsequent Cfree comparisons to be made in two ways: (1) comparing Cfree derived from one thickness using different models and (2) comparing Cfree derived from the same model using different thicknesses of LDPE. Following the deployments, the percent of PRC lost ranged from 0-100%. As expected, fractional equilibrium decreased with increasing PRC molecular weight as well as sampler thickness. Overall, a total of 27 PCBs (log KOW ranging from 5.07 – 8.09) were measured at Cfree concentrations varying from 0.05 pg/L (PCB 206) to about 200 ng/L (PCB 28) on a single LDPE sampler. Relative standard deviations (RSDs) for total PCB measurements using the same thickness and varying model types range from 0.04-12% and increased with sampler thickness. Total PCB RSD for measurements using the same model and varying thickness ranged from: 6 – 30%. No RSD trends between models were observed but RSD did increase as Cfree decreased. These findings indicate that existing models yield precise and reproducible results when using LDPE and PRCs to measure Cfree. This work in

Heterogeneous Deployment Analysis for Cost-Effective Mobile Network Evolution

DEFF Research Database (Denmark)

Coletti, Claudio

2013-01-01

network coverage and boosting network capacity in traffic hot-spot areas. The thesis deals with the deployment of both outdoor small cells and indoor femto cells. Amongst the outdoor solution, particular emphasis is put on relay base stations as backhaul costs can be reduced by utilizing LTE spectrum...... statistical models of deployment areas, the performance analysis is carried out in the form of operator case studies for large-scale deployment scenarios, including realistic macro network layouts and inhomogeneous spatial traffic distributions. Deployment of small cells is performed by means of proposed...... heuristic deployment algorithms, which combine network coverage and spatial user density information. As a secondary aspect, deployment solutions achieving the same coverage performance are compared in terms of Total Cost of Ownership (TCO), in order to investigate the viability of different deployment...

Comprehensive Deployment Method for Technical Characteristics Base on Multi-failure Modes Correlation Analysis

Science.gov (United States)

Zheng, W.; Gao, J. M.; Wang, R. X.; Chen, K.; Jiang, Y.

2017-12-01

This paper put forward a new method of technical characteristics deployment based on Reliability Function Deployment (RFD) by analysing the advantages and shortages of related research works on mechanical reliability design. The matrix decomposition structure of RFD was used to describe the correlative relation between failure mechanisms, soft failures and hard failures. By considering the correlation of multiple failure modes, the reliability loss of one failure mode to the whole part was defined, and a calculation and analysis model for reliability loss was presented. According to the reliability loss, the reliability index value of the whole part was allocated to each failure mode. On the basis of the deployment of reliability index value, the inverse reliability method was employed to acquire the values of technology characteristics. The feasibility and validity of proposed method were illustrated by a development case of machining centre’s transmission system.

The Structure of the Proton in the LHC Precision Era

NARCIS (Netherlands)

Gao, Jun; Harland-Lang, Lucian; Rojo, Juan

2017-01-01

We review recent progress in the determination of the parton distribution functions (PDFs) of the proton, with emphasis on the applications for precision phenomenology at the Large Hadron Collider (LHC). First of all, we introduce the general theoretical framework underlying the global QCD analysis

'Seeing the Dark': Grounding Phenomenal Transparency and Opacity in Precision Estimation for Active Inference.

Science.gov (United States)

Limanowski, Jakub; Friston, Karl

2018-01-01

One of the central claims of the Self-model Theory of Subjectivity is that the experience of being someone - even in a minimal form - arises through a transparent phenomenal self-model, which itself can in principle be reduced to brain processes. Here, we consider whether it is possible to distinguish between phenomenally transparent and opaque states in terms of active inference. We propose a relationship of phenomenal opacity to expected uncertainty or precision; i.e., the capacity for introspective attention and implicit mental action. Thus we associate introspective attention with the deployment of 'precision' that may render the perceptual evidence (for action) opaque, while treating transparency as a necessary aspect of beliefs about action, i.e., 'what I am' doing. We conclude by proposing how we may have to nuance our conception of minimal phenomenal selfhood and agency in light of this active inference conception of transparency-opacity.

Home front: post-deployment mental health and divorces.

Science.gov (United States)

Negrusa, Brighita; Negrusa, Sebastian

2014-06-01

Since 2003, about 14 % of U.S. Army soldiers have reported symptoms of posttraumatic stress disorder (PTSD) following deployments. In this article, we examine how post-deployment symptoms of PTSD and of other mental health conditions are related to the probability of divorce among married active-duty U.S. Army soldiers. For this purpose, we combine Army administrative individual-level longitudinal data on soldiers' deployments, marital history, and sociodemographic characteristics with their self-reported post-deployment health information. Our estimates indicate that time spent in deployment increases the divorce risk among Army enlisted personnel and that PTSD symptoms are associated with further increases in the odds of divorce. Although officers are generally less likely to screen positive for PTSD than enlisted personnel, we find a stronger relationship between PTSD symptoms and divorces among Army officers who are PTSD-symptomatic than among enlisted personnel. We estimate a larger impact of deployments on the divorce risk among female soldiers, but we do not find a differential impact of PTSD symptoms by gender. Also, we find that most of the effect of PTSD symptoms occurs early in the career of soldiers who deploy multiple times.

On Prolonging Network Lifetime through Load-Similar Node Deployment in Wireless Sensor Networks

Science.gov (United States)

Li, Qiao-Qin; Gong, Haigang; Liu, Ming; Yang, Mei; Zheng, Jun

2011-01-01

This paper is focused on the study of the energy hole problem in the Progressive Multi-hop Rotational Clustered (PMRC)-structure, a highly scalable wireless sensor network (WSN) architecture. Based on an analysis on the traffic load distribution in PMRC-based WSNs, we propose a novel load-similar node distribution strategy combined with the Minimum Overlapping Layers (MOL) scheme to address the energy hole problem in PMRC-based WSNs. In this strategy, sensor nodes are deployed in the network area according to the load distribution. That is, more nodes shall be deployed in the range where the average load is higher, and then the loads among different areas in the sensor network tend to be balanced. Simulation results demonstrate that the load-similar node distribution strategy prolongs network lifetime and reduces the average packet latency in comparison with existing nonuniform node distribution and uniform node distribution strategies. Note that, besides the PMRC structure, the analysis model and the proposed load-similar node distribution strategy are also applicable to other multi-hop WSN structures. PMID:22163809

Application of high-precision 3D seismic technology to shale gas exploration: A case study of the large Jiaoshiba shale gas field in the Sichuan Basin

Directory of Open Access Journals (Sweden)

Zuqing Chen

2016-03-01

Full Text Available The accumulation pattern of the marine shale gas in South China is different from that in North America. The former has generally thin reservoirs and complex preservation conditions, so it is difficult to make a fine description of the structural features of shale formations and to reflect accurately the distribution pattern of high-quality shale by using the conventional 2D and 3D seismic exploration technology, which has an adverse effect on the successful deployment of horizontal wells. In view of this, high-precision 3D seismic prospecting focusing on lithological survey was implemented to make an accurate description of the distribution of shale gas sweet spots so that commercial shale gas production can be obtained. Therefore, due to the complex seismic geological condition of Jiaoshiba area in Fuling, SE Sichuan Basin, the observation system of high-precision 3D seismic acquisition should have such features as wide-azimuth angles, small trace intervals, high folds, uniform vertical and horizontal coverage and long spread to meet the needs of the shale gas exploration in terms of structural interpretation, lithological interpretation and fracture prediction. Based on this idea, the first implemented high-precision 3D seismic exploration project in Jiaoshiba area played an important role in the discovery of the large Jiaoshiba shale gas field. Considering that the high-quality marine shale in the Sichuan Basin shows the characteristics of multi-layer development from the Silurian system to the Cambrian system, the strategy of shale gas stereoscopic exploration should be implemented to fully obtain the oil and gas information of the shallow, medium and deep strata from the high-precision 3D seismic data, and ultimately to expand the prospecting achievements in an all-round way to balance the high upstream exploration cost, and to continue to push the efficient shale gas exploration and development process in China.

Do soldiers seek more mental health care after deployment? Analysis of mental health consultations in the Netherlands Armed Forces following deployment to Afghanistan

Directory of Open Access Journals (Sweden)

Elisabeth (Liesbeth M. Taal

2014-08-01

Full Text Available Background: Military deployment to combat zones puts military personnel to a number of physical and mental challenges that may adversely affect mental health. Until now, few studies have been performed in Europe on mental health utilization after military deployment. Objective: We compared the incidence of mental health consultations with the Military Mental Health Service (MMHS of military deployed to Afghanistan to that of non-deployed military personnel. Method: We assessed utilization of the MMHS by the full cohort of the Netherlands Armed Forces enlisted between 2008 and 2010 through linkage of mental health and human resource information systems. Results: The total population consisted of 50,508 military (18,233 deployed, 32,275 non-deployed, who accounted for 1,906 new consultations with the MMHS. The follow-up was limited to the first 2 years following deployment. We observed higher mental health care utilization in deployed vs. non-deployed military personnel; hazard ratio (HR, adjusted for sex, military branch and time in service, 1.84 [95% CI 1.61–2.11] in the first and 1.28 [1.09–1.49] in the second year after deployment. An increased risk of adjustment disorders (HR 2.59 [2.02–3.32] and 1.74 [1.30–2.32] and of anxiety disorders (2.22 [1.52–3.25] and 2.28 [1.50–3.45] including posttraumatic stress disorder (5.15 [2.55–10.40] and 5.28 [2.42–11.50], but not of mood disorders (1.33 [0.90–1.97] and 1.11 [0.68–1.82], was observed in deployed personnel in the first- and second-year post-deployment, respectively. Military personnel deployed in a unit with a higher risk of confrontation with potentially traumatic events had a higher HR (2.13 [1.84–2.47] and 1.40 [1.18–1.67]. Conclusions: Though absolute risk was low, in the first and second year following deployment to Afghanistan there was an 80 and 30% higher risk for mental health problems resulting in a consultation with the Dutch MMHS compared to military never

Do soldiers seek more mental health care after deployment? Analysis of mental health consultations in the Netherlands Armed Forces following deployment to Afghanistan

Science.gov (United States)

Taal, Elisabeth (Liesbeth) M.; Vermetten, Eric; van Schaik, Digna (Anneke) J. F.; Leenstra, Tjalling

2014-01-01

Background Military deployment to combat zones puts military personnel to a number of physical and mental challenges that may adversely affect mental health. Until now, few studies have been performed in Europe on mental health utilization after military deployment. Objective We compared the incidence of mental health consultations with the Military Mental Health Service (MMHS) of military deployed to Afghanistan to that of non-deployed military personnel. Method We assessed utilization of the MMHS by the full cohort of the Netherlands Armed Forces enlisted between 2008 and 2010 through linkage of mental health and human resource information systems. Results The total population consisted of 50,508 military (18,233 deployed, 32,275 non-deployed), who accounted for 1,906 new consultations with the MMHS. The follow-up was limited to the first 2 years following deployment. We observed higher mental health care utilization in deployed vs. non-deployed military personnel; hazard ratio (HR), adjusted for sex, military branch and time in service, 1.84 [95% CI 1.61–2.11] in the first and 1.28 [1.09–1.49] in the second year after deployment. An increased risk of adjustment disorders (HR 2.59 [2.02–3.32] and 1.74 [1.30–2.32]) and of anxiety disorders (2.22 [1.52–3.25] and 2.28 [1.50–3.45]) including posttraumatic stress disorder (5.15 [2.55–10.40] and 5.28 [2.42–11.50]), but not of mood disorders (1.33 [0.90–1.97] and 1.11 [0.68–1.82]), was observed in deployed personnel in the first- and second-year post-deployment, respectively. Military personnel deployed in a unit with a higher risk of confrontation with potentially traumatic events had a higher HR (2.13 [1.84–2.47] and 1.40 [1.18–1.67]). Conclusions Though absolute risk was low, in the first and second year following deployment to Afghanistan there was an 80 and 30% higher risk for mental health problems resulting in a consultation with the Dutch MMHS compared to military never deployed to

Large Deployable Reflector (LDR) feasibility study update

Science.gov (United States)

Alff, W. H.; Banderman, L. W.

1983-01-01

In 1982 a workshop was held to refine the science rationale for large deployable reflectors (LDR) and develop technology requirements that support the science rationale. At the end of the workshop, a set of LDR consensus systems requirements was established. The subject study was undertaken to update the initial LDR study using the new systems requirements. The study included mirror materials selection and configuration, thermal analysis, structural concept definition and analysis, dynamic control analysis and recommendations for further study. The primary emphasis was on the dynamic controls requirements and the sophistication of the controls system needed to meet LDR performance goals.

Laser - Polarized HE-3 Target Used for a Precision Measurement of the Neutron Spin Structure

Energy Technology Data Exchange (ETDEWEB)

Romalis, M

2003-11-05

This thesis describes a precision measurement of the deep inelastic neutron spin structure function g{sub 1}{sup n}(x). The main motivation for the experiment is a test of the Bjorken sum rule. Because of smaller statistical errors and broader kinematic coverage than in previous experiments, we are able to study in detail the behavior of the spin structure function g{sub 1}{sup n}(x) for low values of the Bjorken scaling variable x. We find that it has a strongly divergent behavior, in contradiction to the naive predictions of the Regge theory. This calls into question the methods commonly used for extrapolation of g{sub 1}{sup n}(x) to x = 0. The difference between the proton and the neutron spin structure functions is less divergent at low x, so a test of the Bjorken sum rule is possible. We confirm the sum rule with an accuracy of 8%. The experiment was performed at SLAC using a 50 GeV polarized electron beam and a polarized {sup 3}He target. In this thesis the polarized target is described in detail. We used the technique of Rb optical pumping and Rb-He spin exchange to polarize the {sup 3}He. Because of a novel mechanical design our target had the smallest dilution ever achieved for a high density gas target. Since this is a precision measurement, particular efforts were made to reduce the systematic errors due to the uncertainty in the target parameters. Most important parameters were measured by more than one method. We implemented novel techniques for measuring the thickness of the glass windows of the target, the {sup 3}He density, and the polarization. In particular, one of the methods for measuring the gas density relied on the broadening of the Rb optical absorption lines by collisions with {sup 3}He atoms. The calibration of this technique resulted in the most precise measurements of the pressure broadening parameters for {sup 3}He as well as several other gases, which are described in an Appendix. The polarization of the {sup 3}He was also measured by

The effects of structure anisotropy on lensing observables in an exact general relativistic setting for precision cosmology

Energy Technology Data Exchange (ETDEWEB)

Troxel, M. A.; Ishak, Mustapha; Peel, Austin, E-mail: troxel@utdallas.edu, E-mail: mishak@utdallas.edu, E-mail: austin.peel@utdallas.edu [Department of Physics, The University of Texas at Dallas, Richardson, TX 75080 (United States)

2014-03-01

The study of relativistic, higher order, and nonlinear effects has become necessary in recent years in the pursuit of precision cosmology. We develop and apply here a framework to study gravitational lensing in exact models in general relativity that are not restricted to homogeneity and isotropy, and where full nonlinearity and relativistic effects are thus naturally included. We apply the framework to a specific, anisotropic galaxy cluster model which is based on a modified NFW halo density profile and described by the Szekeres metric. We examine the effects of increasing levels of anisotropy in the galaxy cluster on lensing observables like the convergence and shear for various lensing geometries, finding a strong nonlinear response in both the convergence and shear for rays passing through anisotropic regions of the cluster. Deviation from the expected values in a spherically symmetric structure are asymmetric with respect to path direction and thus will persist as a statistical effect when averaged over some ensemble of such clusters. The resulting relative difference in various geometries can be as large as approximately 2%, 8%, and 24% in the measure of convergence (1−κ) for levels of anisotropy of 5%, 10%, and 15%, respectively, as a fraction of total cluster mass. For the total magnitude of shear, the relative difference can grow near the center of the structure to be as large as 15%, 32%, and 44% for the same levels of anisotropy, averaged over the two extreme geometries. The convergence is impacted most strongly for rays which pass in directions along the axis of maximum dipole anisotropy in the structure, while the shear is most strongly impacted for rays which pass in directions orthogonal to this axis, as expected. The rich features found in the lensing signal due to anisotropic substructure are nearly entirely lost when one treats the cluster in the traditional FLRW lensing framework. These effects due to anisotropic structures are thus likely to

Reintegration Difficulty of Military Couples Following Deployment

Science.gov (United States)

2016-07-01

Response rate for Wave 8 = 88% Our final sample contained 554 men and 556 women (n = 554 cross- sex couples, 1 same- sex couple). Individuals were...story in the Killeen Daily Herald (10 April 2016) http://kdhnews.com/news/local/ kids -deployments-when-a-parent-deploys-children-face- tough...years old), and (c) “Me getting sick and having to go to sick call.” (deployed Army husband, 25 years old). Sex and fidelity. Comments fell into

Market and Policy Barriers to Energy Storage Deployment

Energy Technology Data Exchange (ETDEWEB)

Bhatnagar, Dhruv [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Currier, Aileen [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Hernandez, Jacquelynne [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Ma, Ookie [Dept. of Energy (DOE), Washington DC (United States) Office of Energy Efficiency and Renewable Energy; Kirby, Brendan [Consultant

2013-09-01

Electric energy storage technologies can provide numerous grid services; there are a number of factors that restrict their current deployment. The most significant barrier to deployment is high capital costs, though several recent deployments indicate that capital costs are decreasing and energy storage may be the preferred economic alternative in certain situations. However, a number of other market and regulatory barriers persist, limiting further deployment. These barriers can be categorized into regulatory barriers, market (economic) barriers, utility and developer business model barriers, cross-cutting barriers and technology barriers.

A Remotely Deployable Wind Sonic Anemometer

Directory of Open Access Journals (Sweden)

Muhammad Awais

2017-12-01

Full Text Available Communication and computing shape up base for explosion of Internet of Things (IoT era. Humans can efficiently control the devices around their environment as per requirements because of IoT, the communication between different devices brings more flexibility in surrounding. Useful data is also gathered from some of these devices to create Big Data; where, further analysis assist in making life easier by developing good business models corresponding to user needs, enhance scientific research, formulating weather prediction or monitoring systems and contributing in other relative fields as well. Thus, in this research a remotely deployable IoT enabled Wind Sonic Anemometer has been designed and deployed to calculate average wind speed, direction, and gust. The proposed design is remotely deployable, user-friendly, power efficient and cost-effective because of opted modules i.e., ultrasonic sensors, GSM module, and solar panel. The testbed was also deployed at the roof of Computer & Information Systems Engineering (CIS department, NED UET. Further, its calibration has been carried out by using long short-term memory (LSTM, a deep learning technique; where ground truth data has been gathered from mechanical wind speed sensor (NRG-40 H deployed at top of Industrial & Manufacturing (IM department of NED UET. The obtained results are satisfactory and the performance of designed sensor is also good under various weather conditions.

Environmental issues affecting clean coal technology deployment

Energy Technology Data Exchange (ETDEWEB)

Miller, M.J. [Electric Power Research Inst., Palo Alto, CA (United States)

1997-12-31

The author outlines what he considers to be the key environmental issues affecting Clean Coal Technology (CCT) deployment both in the US and internationally. Since the international issues are difficult to characterize given different environmental drivers in various countries and regions, the primary focus of his remarks is on US deployment. However, he makes some general remarks, particularly regarding the environmental issues in developing vs. developed countries and how these issues may affect CCT deployment. Further, how environment affects deployment depends on which particular type of clean coal technology one is addressing. It is not the author`s intention to mention many specific technologies other than to use them for the purposes of example. He generally categorizes CCTs into four groups since environment is likely to affect deployment for each category somewhat differently. These four categories are: Precombustion technologies such as coal cleaning; Combustion technologies such as low NOx burners; Postcombustion technologies such as FGD systems and postcombustion NOx control; and New generation technologies such as gasification and fluidized bed combustion.

An innovative deployable solar panel system for Cubesats

Science.gov (United States)

Santoni, Fabio; Piergentili, Fabrizio; Donati, Serena; Perelli, Massimo; Negri, Andrea; Marino, Michele

2014-02-01

One of the main Cubesat bus limitations is the available on-board power. The maximum power obtained using body mounted solar panels and advanced triple junction solar cells on a triple unit Cubesat is typically less than 10 W. The Cubesat performance and the mission scenario opened to these small satellite systems could be greatly enhanced by an increase of the available power. This paper describes the design and realization of a modular deployable solar panel system for Cubesats, consisting of a modular hinge and spring system that can be potentially used on-board single (1U), double(2U), triple (3U) and six units (6U) Cubesats. The size of each solar panels is the size of a lateral Cubesat surface. The system developed is the basis for a SADA (Solar Array Drive Assembly), in which a maneuvering capability is added to the deployed solar array in order to follow the apparent motion of the sun. The system design trade-off is discussed, comparing different deployment concepts and architectures, leading to the final selection for the modular design. A prototype of the system has been realized for a 3U Cubesat, consisting of two deployable solar panel systems, made of three solar panels each, for a total of six deployed solar panels. The deployment system is based on a plastic fiber wire and thermal cutters, guaranteeing a suitable level of reliability. A test-bed for the solar panel deployment testing has been developed, supporting the solar array during deployment reproducing the dynamical situation in orbit. The results of the deployment system testing are discussed, including the design and realization of the test-bed, the mechanical stress given to the solar cells by the deployment accelerations and the overall system performance. The maximum power delivered by the system is about 50.4 W BOL, greatly enhancing the present Cubesat solar array performance.

Precision muon physics

Science.gov (United States)

Gorringe, T. P.; Hertzog, D. W.

2015-09-01

The muon is playing a unique role in sub-atomic physics. Studies of muon decay both determine the overall strength and establish the chiral structure of weak interactions, as well as setting extraordinary limits on charged-lepton-flavor-violating processes. Measurements of the muon's anomalous magnetic moment offer singular sensitivity to the completeness of the standard model and the predictions of many speculative theories. Spectroscopy of muonium and muonic atoms gives unmatched determinations of fundamental quantities including the magnetic moment ratio μμ /μp, lepton mass ratio mμ /me, and proton charge radius rp. Also, muon capture experiments are exploring elusive features of weak interactions involving nucleons and nuclei. We will review the experimental landscape of contemporary high-precision and high-sensitivity experiments with muons. One focus is the novel methods and ingenious techniques that achieve such precision and sensitivity in recent, present, and planned experiments. Another focus is the uncommonly broad and topical range of questions in atomic, nuclear and particle physics that such experiments explore.

High precision tracking of a piezoelectric nano-manipulator with parameterized hysteresis compensation

Science.gov (United States)

Yan, Peng; Zhang, Yangming

2018-06-01

High performance scanning of nano-manipulators is widely deployed in various precision engineering applications such as SPM (scanning probe microscope), where trajectory tracking of sophisticated reference signals is an challenging control problem. The situation is further complicated when rate dependent hysteresis of the piezoelectric actuators and the stress-stiffening induced nonlinear stiffness of the flexure mechanism are considered. In this paper, a novel control framework is proposed to achieve high precision tracking of a piezoelectric nano-manipulator subjected to hysteresis and stiffness nonlinearities. An adaptive parameterized rate-dependent Prandtl-Ishlinskii model is constructed and the corresponding adaptive inverse model based online compensation is derived. Meanwhile a robust adaptive control architecture is further introduced to improve the tracking accuracy and robustness of the compensated system, where the parametric uncertainties of the nonlinear dynamics can be well eliminated by on-line estimations. Comparative experimental studies of the proposed control algorithm are conducted on a PZT actuated nano-manipulating stage, where hysteresis modeling accuracy and excellent tracking performance are demonstrated in real-time implementations, with significant improvement over existing results.

The cancer precision medicine knowledge base for structured clinical-grade mutations and interpretations

Science.gov (United States)

Huang, Linda; Fernandes, Helen; Zia, Hamid; Tavassoli, Peyman; Rennert, Hanna; Pisapia, David; Imielinski, Marcin; Sboner, Andrea; Rubin, Mark A; Kluk, Michael

2017-01-01

Objective: This paper describes the Precision Medicine Knowledge Base (PMKB; https://pmkb.weill.cornell.edu), an interactive online application for collaborative editing, maintenance, and sharing of structured clinical-grade cancer mutation interpretations. Materials and Methods: PMKB was built using the Ruby on Rails Web application framework. Leveraging existing standards such as the Human Genome Variation Society variant description format, we implemented a data model that links variants to tumor-specific and tissue-specific interpretations. Key features of PMKB include support for all major variant types, standardized authentication, distinct user roles including high-level approvers, and detailed activity history. A REpresentational State Transfer (REST) application-programming interface (API) was implemented to query the PMKB programmatically. Results: At the time of writing, PMKB contains 457 variant descriptions with 281 clinical-grade interpretations. The EGFR, BRAF, KRAS, and KIT genes are associated with the largest numbers of interpretable variants. PMKB’s interpretations have been used in over 1500 AmpliSeq tests and 750 whole-exome sequencing tests. The interpretations are accessed either directly via the Web interface or programmatically via the existing API. Discussion: An accurate and up-to-date knowledge base of genomic alterations of clinical significance is critical to the success of precision medicine programs. The open-access, programmatically accessible PMKB represents an important attempt at creating such a resource in the field of oncology. Conclusion: The PMKB was designed to help collect and maintain clinical-grade mutation interpretations and facilitate reporting for clinical cancer genomic testing. The PMKB was also designed to enable the creation of clinical cancer genomics automated reporting pipelines via an API. PMID:27789569

Active wavefront control challenges of the NASA Large Deployable Reflector (LDR)

Science.gov (United States)

Meinel, Aden B.; Meinel, Marjorie P.; Manhart, Paul K.; Hochberg, Eric B.

1989-01-01

The 20-m Large Deployable Reflector will have a segmented primary mirror. Achieving diffraction-limited performance at 50 microns requires correction for the errors of tilt and piston of the primary mirror. This correction can be obtained in two ways, the use of an active primary or a correction at a demagnified pupil of the primary. A critical requirement is the means for measurement of the wavefront error and maintaining phasing during the observation of objects that may be too faint for determining the error. Absolute phasing can only be determined using a cooperative source. Maintenance of phasing can be done with an on-board source. A number of options are being explored as discussed below. The many issues concerning the assessment and control of an active segmented mirror will be addressed with an early construction of the Precision Segmented Reflector testbed.

Active wavefront control challenges of the NASA Large Deployable Reflector (LDR)

Science.gov (United States)

Meinel, Aden B.; Meinel, Marjorie P.; Manhart, Paul K.; Hochberg, Eric B.

1989-09-01

The 20-m Large Deployable Reflector will have a segmented primary mirror. Achieving diffraction-limited performance at 50 microns requires correction for the errors of tilt and piston of the primary mirror. This correction can be obtained in two ways, the use of an active primary or a correction at a demagnified pupil of the primary. A critical requirement is the means for measurement of the wavefront error and maintaining phasing during the observation of objects that may be too faint for determining the error. Absolute phasing can only be determined using a cooperative source. Maintenance of phasing can be done with an on-board source. A number of options are being explored as discussed below. The many issues concerning the assessment and control of an active segmented mirror will be addressed with an early construction of the Precision Segmented Reflector testbed.

A field-deployable compound-specific isotope analyzer based on quantum cascade laser and hollow waveguide

Science.gov (United States)

Wu, Sheng; Deev, Andrei

2013-01-01

A field deployable Compound Specific Isotope Analyzer (CSIA) coupled with capillary chromatogrpahy based on Quantum Cascade (QC) lasers and Hollow Waveguide (HWG) with precision and chemical resolution matching mature Mass Spectroscopy has been achieved in our laboratory. The system could realize 0.3 per mil accuracy for 12C/13C for a Gas Chromatography (GC) peak lasting as short as 5 seconds with carbon molar concentration in the GC peak less than 0.5%. Spectroscopic advantages of HWG when working with QC lasers, i.e. single mode transmission, noiseless measurement and small sample volume, are compared with traditional free space and multipass spectroscopy methods.

Multiple-Robot Systems for USAR: Key Design Attributes and Deployment Issues

Directory of Open Access Journals (Sweden)

Choon Yue Wong

2011-03-01

Full Text Available The interaction between humans and robots is undergoing an evolution. Progress in this evolution means that humans are close to robustly deploying multiple robots. Urban search and rescue (USAR can benefit greatly from such capability. The review shows that with state of the art artificial intelligence, robots can work autonomously but still require human supervision. It also shows that multiple robot deployment (MRD is more economical, shortens mission durations, adds reliability as well as addresses missions impossible with one robot and payload constraints. By combining robot autonomy and human supervision, the benefits of MRD can be applied to USAR while at the same time minimizing human exposure to danger. This is achieved with a single-human multiple-robot system (SHMRS. However, designers of the SHMRS must consider key attributes such as the size, composition and organizational structure of the robot collective. Variations in these attributes also induce fluctuations in issues within SHMRS deployment such as robot communication and computational load as well as human cognitive workload and situation awareness (SA. Research is essential to determine how the attributes can be manipulated to mitigate these issues while meeting the requirements of the USAR mission.

Multiple-Robot Systems for USAR: Key Design Attributes and Deployment Issues

Directory of Open Access Journals (Sweden)

Choon Yue Wong

2011-03-01

Full Text Available The interaction between humans and robots is undergoing an evolution. Progress in this evolution means that humans are close to robustly deploying multiple robots. Urban search and rescue (USAR can benefit greatly from such capability. The review shows that with state of the art artificial intelligence, robots can work autonomously but still require human supervision. It also shows that multiple robot deployment (MRD is more economical, shortens mission durations, adds reliability as well as addresses missions impossible with one robot and payload constraints. By combining robot autonomy and human supervision, the benefits of MRD can be applied to USAR while at the same time minimizing human exposure to danger. This is achieved with a single-human multiple-robot system (SHMRS. However, designers of the SHMRS must consider key attributes such as the size, composition and organizational structure of the robot collective. Variations in these attributes also induce fluctuations in issues within SHMRS deployment such as robot communication and computational load as well as human cognitive workload and situation awareness (SA.Research is essential to determine how the attributes can be manipulated to mitigate these issues while meeting the requirements of the USAR mission.

Quantization and training of object detection networks with low-precision weights and activations

Science.gov (United States)

Yang, Bo; Liu, Jian; Zhou, Li; Wang, Yun; Chen, Jie

2018-01-01

As convolutional neural networks have demonstrated state-of-the-art performance in object recognition and detection, there is a growing need for deploying these systems on resource-constrained mobile platforms. However, the computational burden and energy consumption of inference for these networks are significantly higher than what most low-power devices can afford. To address these limitations, this paper proposes a method to train object detection networks with low-precision weights and activations. The probability density functions of weights and activations of each layer are first directly estimated using piecewise Gaussian models. Then, the optimal quantization intervals and step sizes for each convolution layer are adaptively determined according to the distribution of weights and activations. As the most computationally expensive convolutions can be replaced by effective fixed point operations, the proposed method can drastically reduce computation complexity and memory footprint. Performing on the tiny you only look once (YOLO) and YOLO architectures, the proposed method achieves comparable accuracy to their 32-bit counterparts. As an illustration, the proposed 4-bit and 8-bit quantized versions of the YOLO model achieve a mean average precision of 62.6% and 63.9%, respectively, on the Pascal visual object classes 2012 test dataset. The mAP of the 32-bit full-precision baseline model is 64.0%.

An economic evaluation of alternative biofuel deployment scenarios in the USA

Directory of Open Access Journals (Sweden)

Gbadebo Oladosu

2017-05-01

Full Text Available Energy market conditions have shifted dramatically since the USA renewable fuel standards (RFS1 in 2005; RFS2 in 2007 were enacted. The USA has transitioned from an increasing dependence on oil imports to abundant domestic oil production. In addition, increases in the use of ethanol, the main biofuel currently produced in the USA, is now limited by the blend wall constraint. Given this, the current study evaluates alternative biofuel deployment scenarios in the USA, accounting for changes in market conditions. The analysis is performed with a general equilibrium model that reflects the structure of the USA biofuel market as the transition to advanced biofuels begins. Results suggest that ethanol consumption would increase, albeit slowly, if current biofuel deployment rates of about 10% are maintained as persistently lower oil prices lead to a gradual increase in the consumption of liquid transportation fuels. Without the blend wall constraint, this study finds that the overall economic impact of a full implementation of the USA RFS2 policy is largely neutral before 2022. However, the economic impacts become slightly negative under the blend wall constraint since more expensive bio-hydrocarbons are needed to meet the RFS2 mandates. Results for a scenario with reduced advanced biofuel deployment based on current policy plans show near neutral economic impacts up to 2027. This scenario is also consistent with another scenario where the volume of bio-hydrocarbons deployed is reduced to adjust for its higher cost and energy content relative to deploying the mandated RFS2 advanced biofuel volumes as ethanol. The important role of technological change is demonstrated under pioneer and accelerated technology scenarios, with the latter leading to neutral or positive economic effects up to 2023 under most blend wall scenarios. All scenarios evaluated in this study are found to have positive long-term benefits for the USA economy.

High-precision multi-node clock network distribution.

Science.gov (United States)

Chen, Xing; Cui, Yifan; Lu, Xing; Ci, Cheng; Zhang, Xuesong; Liu, Bo; Wu, Hong; Tang, Tingsong; Shi, Kebin; Zhang, Zhigang

2017-10-01

A high precision multi-node clock network for multiple users was built following the precise frequency transmission and time synchronization of 120 km fiber. The network topology adopts a simple star-shaped network structure. The clock signal of a hydrogen maser (synchronized with UTC) was recovered from a 120 km telecommunication fiber link and then was distributed to 4 sub-stations. The fractional frequency instability of all substations is in the level of 10 -15 in a second and the clock offset instability is in sub-ps in root-mean-square average.

Precision Oncology: Between Vaguely Right and Precisely Wrong.

Science.gov (United States)

Brock, Amy; Huang, Sui

2017-12-01

Precision Oncology seeks to identify and target the mutation that drives a tumor. Despite its straightforward rationale, concerns about its effectiveness are mounting. What is the biological explanation for the "imprecision?" First, Precision Oncology relies on indiscriminate sequencing of genomes in biopsies that barely represent the heterogeneous mix of tumor cells. Second, findings that defy the orthodoxy of oncogenic "driver mutations" are now accumulating: the ubiquitous presence of oncogenic mutations in silent premalignancies or the dynamic switching without mutations between various cell phenotypes that promote progression. Most troublesome is the observation that cancer cells that survive treatment still will have suffered cytotoxic stress and thereby enter a stem cell-like state, the seeds for recurrence. The benefit of "precision targeting" of mutations is inherently limited by this counterproductive effect. These findings confirm that there is no precise linear causal relationship between tumor genotype and phenotype, a reminder of logician Carveth Read's caution that being vaguely right may be preferable to being precisely wrong. An open-minded embrace of the latest inconvenient findings indicating nongenetic and "imprecise" phenotype dynamics of tumors as summarized in this review will be paramount if Precision Oncology is ultimately to lead to clinical benefits. Cancer Res; 77(23); 6473-9. ©2017 AACR . ©2017 American Association for Cancer Research.

Review of deployment technology for tethered satellite systems

Science.gov (United States)

Yu, B. S.; Wen, H.; Jin, D. P.

2018-03-01

Tethered satellite systems (TSSs) have attracted significant attention due to their potential and valuable applications for scientific research. With the development of various launched on-orbit missions, the deployment of tethers is considered a crucial technology for operation of a TSS. Both past orbiting experiments and numerical results have shown that oscillations of the deployed tether due to the Coriolis force and environmental perturbations are inevitable and that the impact between the space tether and end-body at the end of the deployment process leads to complicated nonlinear phenomena. Hence, a set of suitable control methods plays a fundamental role in tether deployment. This review article summarizes previous work on aspects of the dynamics, control, and ground-based experiments of tether deployment. The relevant basic principles, analytical expressions, simulation cases, and experimental results are presented as well.

Regio-Regular Oligo and Poly(3-hexyl thiophene): Precise Structural Markers from the Vibrational Spectra of Oligomer Single Crystals.

KAUST Repository

Brambilla, Luigi

2014-10-14

© 2014 American Chemical Society. In this work, we report a comparative analysis of the infrared and Raman spectra of octa(3-hexylthiophene) (3HT)8, trideca(3-hexylthiophene) (3HT)13, and poly(3-hexylthiophene) P3HT recorded in various phases, namely, amorphous, semicrystalline, polycrystalline and single crystal. We have based our analysis on the spectra of the (3HT)8 single crystal (whose structure has been determined by selected area electron diffraction) taken as reference and on the results of DFT calculations and molecular vibrational dynamics. New and precise spectroscopic markers of the molecular structures show the existence of three phases, namely: hairy (phase 1), ordered (phase 2), and disordered/amorphous (phase 3). Conceptually, the identified markers can be used for the molecular structure analysis of other similar systems.

Differential Child Maltreatment Risk Across Deployment Periods of US Army Soldiers.

Science.gov (United States)

Taylor, Christine M; Ross, Michelle E; Wood, Joanne N; Griffis, Heather M; Harb, Gerlinde C; Mi, Lanyu; Song, Lihai; Strane, Douglas; Lynch, Kevin G; Rubin, David M

2016-01-01

We described the risk for maltreatment among toddlers of US Army soldiers over different deployment cycles to develop a systematic response within the US Army to provide families appropriate supports. We conducted a person-time analysis of substantiated maltreatment reports and medical diagnoses among children of 112,325 deployed US Army soldiers between 2001 and 2007. Risk of maltreatment was elevated after deployment for children of soldiers deployed once but not for children of soldiers deployed twice. During the 6 months after deployment, children of soldiers deployed once had 4.43 substantiated maltreatment reports and 4.96 medical diagnoses per 10,000 child-months. The highest maltreatment rate among children of soldiers deployed twice occurred during the second deployment for substantiated maltreatment (4.83 episodes per 10,000 child-months) and before the first deployment for medical diagnoses of maltreatment (3.78 episodes per 10,000 child-months). We confirmed an elevated risk for child maltreatment during deployment but also found a previously unidentified high-risk period during the 6 months following deployment, indicating elevated stress within families of deployed and returning soldiers. These findings can inform efforts by the military to initiate and standardize support and preparation to families during periods of elevated risk.

Psychiatric Effects of Military Deployment on Children and Families

Science.gov (United States)

James, Trenton

2012-01-01

Deployments in the United States military have increased greatly in the past 10 years. Families and children are psychiatrically affected by these deployments, and recent studies are clarifying these effects. This article focuses on the psychiatric effects of deployment on children and uses a composite case example to review the use of play therapy to treat children who are having psychiatric issues related to the deployment of one or both parents. PMID:22468239

Net Metering and Market Feedback Loops: Exploring the Impact of Retail Rate Design on Distributed PV Deployment

Energy Technology Data Exchange (ETDEWEB)

Darghouth, Naïm R. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Wiser, Ryan [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Barbose, Galen [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Mills, Andrew [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2015-01-13

The substantial increase in deployment of customer-sited solar photovoltaics (PV) in the United States has been driven by a combination of steeply declining costs, financing innovations, and supportive policies. Among those supportive policies is net metering, which in most states effectively allows customers to receive compensation for distributed PV generation at the full retail electricity price. The current design of retail electricity rates and the presence of net metering have elicited concerns that the possible under-recovery of fixed utility costs from PV system owners may lead to a feedback loop of increasing retail prices that accelerate PV adoption and further rate increases. However, a separate and opposing feedback loop could offset this effect: increased PV deployment may lead to a shift in the timing of peak-period electricity prices that could reduce the bill savings received under net metering where time-varying retail electricity rates are used, thereby dampening further PV adoption. In this paper, we examine the impacts of these two competing feedback dynamics on U.S. distributed PV deployment through 2050 for both residential and commercial customers, across states. Our results indicate that, at the aggregate national level, the two feedback effects nearly offset one another and therefore produce a modest net effect, although their magnitude and direction vary by customer segment and by state. We also model aggregate PV deployment trends under various rate designs and net-metering rules, accounting for feedback dynamics. Our results demonstrate that future adoption of distributed PV is highly sensitive to retail rate structures. Whereas flat, time-invariant rates with net metering lead to higher aggregate national deployment levels than the current mix of rate structures (+5% in 2050), rate structures with higher monthly fixed customer charges or PV compensation at levels lower than the full retail rate can dramatically erode aggregate customer

Garden State Parkway Corridor : ITS early deployment planning study : strategic deployment plan

Science.gov (United States)

1997-12-01

This Strategic Deployment Plan describes ways of improving travel within the Garden : State Parkway Corridor using intelligent transportation systems (ITS) and without : constructing additional roadway lanes. Travel improvements will be possible with...

Deployment Instabilities of Lobed-Pumpkin Balloon

Science.gov (United States)

Nakashino, Kyoichi

A lobed-pumpkin balloon, currently being developed in ISAS/JAXA as well as in NASA, is a promising vehicle for long duration scientific observations in the stratosphere. Recent ground and flight experiments, however, have revealed that the balloon has deployment instabilities under certain conditions. In order to overcome the instability problems, a next generation SPB called 'tawara' type balloon has been proposed, in which an additional cylindrical part is appended to the standard lobed-pumpkin balloon. The present study investigates the deployment stability of tawara type SPB in comparison to that of standard lobed-pumpkin SPB through eigenvalue analysis on the basis of finite element methods. Our numerical results show that tawara type SPB enjoys excellent deployment performance over the standard lobed-pumpkin SPBs.

Large Deployable Reflector (LDR)

Science.gov (United States)

Alff, W. H.

1980-01-01

The feasibility and costs were determined for a 1 m to 30 m diameter ambient temperature, infrared to submillimeter orbiting astronomical telescope which is to be shuttle-deployed, free-flying, and have a 10 year orbital life. Baseline concepts, constraints on delivery and deployment, and the sunshield required are examined. Reflector concepts, the optical configuration, alignment and pointing, and materials are also discussed. Technology studies show that a 10 m to 30 m diameter system which is background and diffraction limited at 30 micron m is feasible within the stated time frame. A 10 m system is feasible with current mirror technology, while a 30 m system requires technology still in development.

Next generation sensing platforms for extended deployments in large-scale, multidisciplinary, adaptive sampling and observational networks

Science.gov (United States)

Cross, J. N.; Meinig, C.; Mordy, C. W.; Lawrence-Slavas, N.; Cokelet, E. D.; Jenkins, R.; Tabisola, H. M.; Stabeno, P. J.

2016-12-01

New autonomous sensors have dramatically increased the resolution and accuracy of oceanographic data collection, enabling rapid sampling over extremely fine scales. Innovative new autonomous platofrms like floats, gliders, drones, and crawling moorings leverage the full potential of these new sensors by extending spatiotemporal reach across varied environments. During 2015 and 2016, The Innovative Technology for Arctic Exploration Program at the Pacific Marine Environmental Laboratory tested several new types of fully autonomous platforms with increased speed, durability, and power and payload capacity designed to deliver cutting-edge ecosystem assessment sensors to remote or inaccessible environments. The Expendable Ice-Tracking (EXIT) gloat developed by the NOAA Pacific Marine Environmental Laboratory (PMEL) is moored near bottom during the ice-free season and released on an autonomous timer beneath the ice during the following winter. The float collects a rapid profile during ascent, and continues to collect critical, poorly-accessible under-ice data until melt, when data is transmitted via satellite. The autonomous Oculus sub-surface glider developed by the University of Washington and PMEL has a large power and payload capacity and an enhanced buoyancy engine. This 'coastal truck' is designed for the rapid water column ascent required by optical imaging systems. The Saildrone is a solar and wind powered ocean unmanned surface vessel (USV) developed by Saildrone, Inc. in partnership with PMEL. This large-payload (200 lbs), fast (1-7 kts), durable (46 kts winds) platform was equipped with 15 sensors designed for ecosystem assessment during 2016, including passive and active acoustic systems specially redesigned for autonomous vehicle deployments. The senors deployed on these platforms achieved rigorous accuracy and precision standards. These innovative platforms provide new sampling capabilities and cost efficiencies in high-resolution sensor deployment

Cooperative Technolgy Deployed

NARCIS (Netherlands)

Koenders, E.; Velt, R. in 't

2011-01-01

After the successful demonstrations of cooperative technology by the CVIS and Safespot projects the question remains how this technology can be successfully deployed. This question is explored by the Field Operational Test project FREILOT, which aims to provide fuel economy applications that must be

Swarm Deployable Boom Assembly (DBA) Development of a Deployable Magnetometer Boom for the Swarm Spacecraft

Science.gov (United States)

McMahon, Paul; Jung, Hans-Juergen; Edwards, Jeff

2013-09-01

The Swarm programme consists of 3 magnetically clean satellites flying in close formation designed to measure the Earth's magnetic field using 2 Magnetometers mounted on a 4.3m long deployable boom.Deployment is initiated by releasing 3 HDRMs, once released the boom oscillates back and forth on a pair of pivots, similar to a restaurant kitchen door hinge, for around 120 seconds before coming to rest on 3 kinematic mounts which are used to provide an accurate reference location in the deployed position. Motion of the boom is damped through a combination of friction, spring hysteresis and flexing of the 120+ cables crossing the hinge. Considerable development work and accurate numerical modelling of the hinge motion was required to predict performance across a wide temperature range and ensure that during the 1st overshoot the boom did not damage itself, the harness or the spacecraft.Due to the magnetic cleanliness requirements of the spacecraft no magnetic materials could be used in the design of the hardware.

Regulatory potential for increasing small scale grid connected photovoltaic (PV) deployment in Australia

International Nuclear Information System (INIS)

Sivaraman, Deepak; Horne, Ralph E.

2011-01-01

The last decade has seen significant innovation and change in regulatory incentives to support photovoltaic deployment globally. With high fossil fuel dependency and abundant solar resource availability in Australia, grid connected photovoltaics are a viable low carbon technology option in existing electricity grids. Drawing on international examples, the potential to increase grid PV deployment through government response and regulation is explored. For each renewable energy certificate (REC) earned by small scale photovoltaics until 2012, the market provides four additional certificates under the current banded renewable targets. Our analysis indicates that REC eligibility is not accurately estimated currently, and an energy model is developed to calculate the variance. The energy model estimates as much as 26% additional REC's to be obtained by a 3 kWp PV system, when compared to the currently used regulatory method. Moreover, the provision of REC's increases benefits to PV technologies, in the process distorting CO 2 abatement (0.21 tonne/REC) by 68%, when PV displaces peaking natural gas plants. Consideration of the secondary effects of a banded structure on emissions trading market is important in the context of designing a range of initiatives intended to support a transition to a low carbon electricity sector. - Research Highlights: →Grid connected photovoltaics hedge spikes in peak demand summer electricity prices. →Nationwide feed in tariff and new building regulations needed to increase PV deployment. →Australia has transitioned from a solar rebate to a banded solar credit structure. →The currently used regulatory deeming method underestimates REC eligibility by 27%. →The banded structure can potentially distort CO 2 abatement by as much as 68%.

Center for Deployment Psychology

Data.gov (United States)

Federal Laboratory Consortium — The Center for Deployment Psychology was developed to promote the education of psychologists and other behavioral health specialists about issues pertaining to the...

The quality and testing PH-SFT infrastructure for the external LHC software packages deployment

CERN Multimedia

CERN. Geneva; MENDEZ LORENZO, Patricia; MATO VILA, Pere

2015-01-01

The PH-SFT group is responsible for the build, test, and deployment of the set of external software packages used by the LHC experiments. This set includes ca. 170 packages including Grid packages and Montecarlo generators provided for different versions. A complete build structure has been established to guarantee the quality of the packages provided by the group. This structure includes an experimental build and three daily nightly builds, each of them dedicated to a specific ROOT version including v6.02, v6.04, and the master. While the former build is dedicated to the test of new packages, versions and dependencies (basically SFT internal used), the three latter ones are the responsible for the deployment to AFS of the set of stable and well tested packages requested by the LHC experiments so they can apply their own builds on top. In all cases, a c...

Finding Their Way Back In: Family Reintegration Following Guard Deployment.

Science.gov (United States)

Messecar, Deborah C

2017-03-01

The aim of this study was to describe deployed National Guard members' and their families' perceptions of their experience with family reintegration, and the causes and conditions of challenges reintegration presents after deployment. A total of 26 National Guard members and 19 family members participated in individual (n = 22), couples (n = 6), or focus group (n = 17) interviews. In-depth interviews were used to assess needs and maximize input from military families regarding deployment-related experiences and reintegration issues. Qualitative coding and analysis of data were completed using NVivo. Finding their way back in is the key process that the military members must complete to successfully reestablish their desired social connections with the family and reclaim their place within the family. Several conditions shape the degree of challenges with reintegration that veterans and their family will encounter. These include preparation for deployment, length and type of deployment, communication during deployment, and finally, awareness of how deployment changes the military member and the family. Support resources dedicated to providing National Guard members and their families with assistance in preparing for deployments and educating them about the importance of communication during deployment should be maintained and expanded. Broader educational efforts that increase awareness of what to expect regarding how deployment changes the military member and the family are needed. Reprint & Copyright © 2017 Association of Military Surgeons of the U.S.

Towards a theory of PACS deployment: an integrative PACS maturity framework.

Science.gov (United States)

van de Wetering, Rogier; Batenburg, Ronald

2014-06-01

Owing to large financial investments that go along with the picture archiving and communication system (PACS) deployments and inconsistent PACS performance evaluations, there is a pressing need for a better understanding of the implications of PACS deployment in hospitals. We claim that there is a gap in the research field, both theoretically and empirically, to explain the success of the PACS deployment and maturity in hospitals. Theoretical principles are relevant to the PACS performance; maturity and alignment are reviewed from a system and complexity perspective. A conceptual model to explain the PACS performance and a set of testable hypotheses are then developed. Then, structural equation modeling (SEM), i.e. causal modeling, is applied to validate the model and hypotheses based on a research sample of 64 hospitals that use PACS, i.e. 70 % of all hospitals in the Netherlands. Outcomes of the SEM analyses substantiate that the measurements of all constructs are reliable and valid. The PACS alignment-modeled as a higher-order construct of five complementary organizational dimensions and maturity levels-has a significant positive impact on the PACS performance. This result is robust and stable for various sub-samples and segments. This paper presents a conceptual model that explains how alignment in deploying PACS in hospitals is positively related to the perceived performance of PACS. The conceptual model is extended with tools as checklists to systematically identify the improvement areas for hospitals in the PACS domain. The holistic approach towards PACS alignment and maturity provides a framework for clinical practice.

Small cell networks deployment, management, and optimization

CERN Document Server

Claussen, Holger; Ho, Lester; Razavi, Rouzbeh; Kucera, Stepan

2018-01-01

Small Cell Networks: Deployment, Management, and Optimization addresses key problems of the cellular network evolution towards HetNets. It focuses on the latest developments in heterogeneous and small cell networks, as well as their deployment, operation, and maintenance. It also covers the full spectrum of the topic, from academic, research, and business to the practice of HetNets in a coherent manner. Additionally, it provides complete and practical guidelines to vendors and operators interested in deploying small cells. The first comprehensive book written by well-known researchers and engineers from Nokia Bell Labs, Small Cell Networks begins with an introduction to the subject--offering chapters on capacity scaling and key requirements of future networks. It then moves on to sections on coverage and capacity optimization, and interference management. From there, the book covers mobility management, energy efficiency, and small cell deployment, ending with a section devoted to future trends and applicat...

RSOI: Force Deployment Bottleneck

National Research Council Canada - National Science Library

D'Amato, Mark

1998-01-01

This study uses The Theory Of Constraints (TOC) management methodology and recent military missions to show that RSOI operations are generally the limiting constraint to force deployment operations...

Verification Test for Ultra-Light Deployment Mechanism for Sectioned Deployable Antenna Reflectors

Science.gov (United States)

Zajac, Kai; Schmidt, Tilo; Schiller, Marko; Seifart, Klaus; Schmalbach, Matthias; Scolamiero, Lucio

2013-09-01

The ultra-light deployment mechanism (UDM) is based on three carbon fibre reinforced plastics (CFRP) curved tape springs made of carbon fibre / cyanate ester prepregs.In the frame of the activity its space application suitability for the deployment of solid reflector antenna sections was investigated. A projected diameter of the full reflector of 4 m to 7 m and specific mass in the order of magnitude of 2.6kg/m2 was focused for requirement derivation.Extensive verification tests including health checks, environmental and functional tests were carried out with an engineering model to enable representative characterizing of the UDM unit.This paper presents the design and a technical description of the UDM as well as a summary of achieved development status with respect to test results and possible design improvements.

Deployment Testing of the De-Orbit Sail Flight Hardware

OpenAIRE

Hillebrandt, Martin; Meyer, Sebastian; Zander, Martin; Hühne, Christian

2015-01-01

The paper describes the results of the deployment testing of the De-Orbit Sail flight hardware, a drag sail for de-orbiting applications, performed by DLR. It addresses in particular the deployment tests of the fullscale sail subsystem and deployment force tests performed on the boom deployment module. For the fullscale sail testing a gravity compensation device is used which is described in detail. It allows observations of the in-plane interaction of the booms with the sail membrane and the...

IPv6 deployment and management

CERN Document Server

Dooley, Michael

2013-01-01

A guide for understanding, deploying, and managing Internet Protocol version 6 The growth of the Internet has created a need for more addresses than are available with Internet Protocol version 4 (IPv4)-the protocol currently used to direct almost all Internet traffic. Internet Protocol version 6 (IPv6)-the new IP version intended to ultimately succeed IPv4-will expand the addressing capacity of the Internet to support the explosive growth of users and devices on the Internet as well as add flexibility to allocating addresses and efficiency for routing traffic. IPv6 Deploy

Pushing the precision frontier in Collider Physics

CERN Multimedia

CERN. Geneva

2017-01-01

The interplay between precise theory predictions and experimental measurements has written a success story in particle physics. After a brief journey into history we will review recent developments which have led  to "revolutions" with regard to precision calculations and to new insights into the structure of quantum field theory. The second part of the talk will focus on phenomenology, especially on Higgs boson pair production as a window to physics beyond the Standard Model, manifesting itself in a modification of those Higgs couplings which are still to a large extent unconstrained, in particular the Higgs boson self-coupling.

Deploying Node.js

CERN Document Server

Pasquali, Sandro

2015-01-01

If you are an intermediate or advanced developer deploying your Node.js applications, then this book is for you. If you have already built a Node application or module and want to take your knowledge to the next level, this book will help you find your way.

Communication tools between Grid virtual organisations, middleware deployers and sites

CERN Document Server

Dimou, Maria

2008-01-01

Grid Deployment suffers today from the difficulty to reach users and site administrators when a package or a configuration parameter changes. Release notes, twiki pages and news’ broadcasts are not efficient enough. The interest of using GGUS as an efficient and effective intra-project communication tool is the message to the user community presented here. The purpose of GGUS is to bring together End Users and Supporters in the Regions where the Grid is deployed and in operation. Today’s Grid usage is still very far from the simplicity and functionality of the web. While pressing for middleware usability, we try to turn the Global Grid User Support (GGUS) into the central tool for identifying areas in the support environment that need attention. To do this, we exploit GGUS' capacity to expand, by including new Support Units that follow the project's operational structure. Using tailored GGUS database searches we obtain concrete results that prove where we need to improve procedures, Service Level Agreemen...

Solarbus Solar Array Innovative Light Weight Mechanical Architecture with Thin Lateral Panels Deployed with Shape Memory Alloy Regulator

Science.gov (United States)

D'Abrigeon, Laurent; Carpine, Anne; Laduree, Gregory

2005-05-01

The standard ALCATEL SOLAR ARRAY PLANAR CONCEPT on the TELECOM market today on flight is named SOLARBUS.This concept is:• 3 to 10 identical panels covered with Si Hi-η celltechnology.• A central mast constitute by 3 to 4 panels and 1yoke linked together by hinges and synchronizedby cables.• From 2 to 6 lateral panelsThis concept is able to fit with the customer requirements in order to have a competitive "global offer at system level" (mass to power ratio 48-50 W/Kg)But, for the near future, in line with the market trend, and based on the previous experience, an improvement of the SOLARBUS Solar Array concept in term of W/kg/€ is essential in order to maintain the competitiveness of the global ALCATEL offer at system level.In order to increase the W/Kg performance Alcatel has developed a new architecture named Lightweight Panel Structure (LPS). The objectives of this new structure are :• To decrease the kg/m2 ratio • To be compatible of all promising cells technology including Si Hi-n, GaAs, GaAs+ small reflectors. This new architecture is based on the fact that during the 3 major life phases of a Solar Array (Launch/Deployment/Deployed orbital life), the structural needs are more important for the central panels than for the lateral panels.So two different panels have been designed :• Central panels (named LPS1)• Lateral panels (named LPS2)The stowing configuration as been adapted : 2 thin lateral panels LPS2 between 2 structural central panels LPS1, and local bumpers to transfer the loads from LPS2 to LPS1.Also one of the more stringent loads applied to the panels are corresponding to deployment loads. In order to limit the mass of reinforcement of the panels, a deployment speed regulator shall be used. In the frame of the new generation of solar arrays, Alcatel has developed a new actuator based on shape memory alloy torsional rod. This light weight component is directly connected to heaters lines and is able to provide great actuation torque

Deployable reflector configurations

Science.gov (United States)

Meinel, A. B.; Meinel, M. P.; Woolf, N. J.

Both the theoretical reasons for considering a non-circular format for the Large Deployable Reflector, and a potentially realizable concept for such a device, are discussed. The optimum systems for diffraction limited telescopes with incoherent detection have either a single filled aperture, or two such apertures as an interferometer to synthesize a larger aperture. For a single aperture of limited area, a reflector in the form of a slot can be used to give increased angular resolution. It is shown how a 20 x 8 meter telescope can be configured to fit the Space Shuttle bay, and deployed with relatively simple operations. The relationship between the sunshield design and the inclination of the orbit is discussed. The possible use of the LDR as a basic module to permit the construction of supergiant space telescopes and interferometers both for IR/submm studies and for the entire ultraviolet through mm wave spectral region is discussed.

Opportunities for the Cardiovascular Community in the Precision Medicine Initiative.

Science.gov (United States)

Shah, Svati H; Arnett, Donna; Houser, Steven R; Ginsburg, Geoffrey S; MacRae, Calum; Mital, Seema; Loscalzo, Joseph; Hall, Jennifer L

2016-01-12

The Precision Medicine Initiative recently announced by President Barack Obama seeks to move the field of precision medicine more rapidly into clinical care. Precision medicine revolves around the concept of integrating individual-level data including genomics, biomarkers, lifestyle and other environmental factors, wearable device physiological data, and information from electronic health records to ultimately provide better clinical care to individual patients. The Precision Medicine Initiative as currently structured will primarily fund efforts in cancer genomics with longer-term goals of advancing precision medicine to all areas of health, and will be supported through creation of a 1 million person cohort study across the United States. This focused effort on precision medicine provides scientists, clinicians, and patients within the cardiovascular community an opportunity to work together boldly to advance clinical care; the community needs to be aware and engaged in the process as it progresses. This article provides a framework for potential involvement of the cardiovascular community in the Precision Medicine Initiative, while highlighting significant challenges for its successful implementation. © 2016 American Heart Association, Inc.

The risk for marital infidelity across a year-long deployment.

Science.gov (United States)

Balderrama-Durbin, Christina; Stanton, Kimberley; Snyder, Douglas K; Cigrang, Jeffrey A; Talcott, G Wayne; Smith Slep, Amy M; Heyman, Richard E; Cassidy, Daniel G

2017-08-01

Military deployment can create significant relationship strain. Although most couples navigate the challenges of deployment successfully, this period may render some couples more vulnerable to adverse relationship outcomes such as infidelity due to a convergence of factors including geographic separation and reduced emotional and physical intimacy. Despite anecdotal reports of increased rates of infidelity during deployment, empirical findings are lacking. This study used a prospective design to examine the prevalence and risk factors of infidelity across the deployment cycle including a year-long deployment to Iraq. A total of 63 married male Airmen were assessed both pre- and 6-9 months postdeployment. The rate of sexual infidelity prior to deployment (21%) was commensurate with the lifetime rate of sexual involvement outside the marriage in representative community samples of men. Across the deployment period, the prevalence of sexual infidelity was strikingly high (22.6%) compared with annual community estimates (1.5-4%; Allen et al., 2005). Findings demonstrated that service members with a prior history of separation, steps toward divorce, and relationship distress prior to deployment had elevated risk for infidelity over the deployment cycle. Moreover, roughly 75% of Airmen who experienced infidelity over the deployment cycle divorced by 6-9 months postdeployment whereas only 5% of service members without infidelity divorced during this same time period. Considering well-documented adverse impacts of infidelity and divorce, the current findings may assist in identifying military couples at risk for infidelity and informing targeted prevention or early intervention strategies for these couples prior to or immediately following deployment. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Adaptable Deployable Entry & Placement Technology (ADEPT) for Cubesat Delivery to Mars Surface

Science.gov (United States)

Wercinski, Paul

2014-01-01

The Adaptable, Deployable Entry and Placement Technology (ADEPT), uses a mechanical skeleton to deploy a revolutionary carbon fabric system that serves as both heat shield and primary structure during atmospheric entry. The NASA ADEPT project, currently funded by the Game Changing Development Program in STMD is currently focused on 1m class hypersonic decelerators for the delivery of very small payloads ( 5 kg) to locations of interest in an effort to leverage low-cost platforms to rapidly mature the technology while simultaneously delivering high-value science. Preliminary mission design and aerothermal performance testing in arcjets have shown the ADEPT system is quite capable of safe delivery of cubesats to Mars surface. The ability of the ADEPT to transit to Mars in a stowed configuration (similar to an umbrella) provides options for integration with the Mars 2020 cruise stage, even to consider multiple ADEPTs. System-level test campaigns are underway for FY15 execution or planning for FY16. These include deployment testing, wind tunnel testing, system-level arc jet testing, and a sounding rocket flight test. The goal is system level maturation (TRL 6) at a 1m class Mars design reference mission configuration.

Precise Design of Phosphorescent Molecular Butterflies with Tunable Photoinduced Structural Change and Dual Emission.

Science.gov (United States)

Zhou, Chenkun; Tian, Yu; Yuan, Zhao; Han, Mingu; Wang, Jamie; Zhu, Lei; Tameh, Maliheh Shaban; Huang, Chen; Ma, Biwu

2015-08-10

Photoinduced structural change (PSC) is a fundamental excited-state dynamic process in chemical and biological systems. However, precise control of PSC processes is very challenging, owing to the lack of guidelines for designing excited-state potential energy surfaces (PESs). A series of rationally designed butterfly-like phosphorescent binuclear platinum complexes that undergo controlled PSC by Pt-Pt distance shortening and exhibit tunable dual (greenish-blue and red) emission are herein reported. Based on the Bell-Evans-Polanyi principle, it is demonstrated how the energy barrier of the PSC, which can be described as a chemical-reaction-like process between the two energy minima on the first triplet excited-state PES, can be controlled by synthetic means. These results reveal a simple method to engineer the dual emission of molecular systems by manipulating PES to control PSC. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Precision electroweak physics at LEP

Energy Technology Data Exchange (ETDEWEB)

Mannelli, M.

1994-12-01

Copious event statistics, a precise understanding of the LEP energy scale, and a favorable experimental situation at the Z{sup 0} resonance have allowed the LEP experiments to provide both dramatic confirmation of the Standard Model of strong and electroweak interactions and to place substantially improved constraints on the parameters of the model. The author concentrates on those measurements relevant to the electroweak sector. It will be seen that the precision of these measurements probes sensitively the structure of the Standard Model at the one-loop level, where the calculation of the observables measured at LEP is affected by the value chosen for the top quark mass. One finds that the LEP measurements are consistent with the Standard Model, but only if the mass of the top quark is measured to be within a restricted range of about 20 GeV.

Policy stakeholders and deployment of wind power in the sub-national context: A comparison of four U.S. states

International Nuclear Information System (INIS)

Fischlein, Miriam; Larson, Joel; Hall, Damon M.; Chaudhry, Rumika; Rai Peterson, Tarla; Stephens, Jennie C.; Wilson, Elizabeth J.

2010-01-01

As climate change mitigation gains attention in the United States, low-carbon energy technologies such as wind power encounter both opportunities and barriers en route to deployment. This paper provides a state-level context for examining wind power deployment and presents research on how policy stakeholders perceive wind energy in four states: Massachusetts, Minnesota, Montana, and Texas. Through semi-structured interviews, state-level energy policy stakeholders were asked to explain their perceptions of wind energy technology within their state. Interview texts were coded to assess how various drivers promote or hinder the deployment of wind power in sub-national contexts. Responses were dominated by technical, political, and economic frames in all four states, but were often driven by a very different rationale. Environmental, aesthetic, and health/safety frames appeared less often in the discourse. This analysis demonstrates that each state arrived at its current level of deployment via very different political, economic, and technical paths. In addition to helping explain why and how wind technology was - or was not - deployed in each of these states, these findings provide insight into the diversity of sub-national dialogues on deployment of low-carbon energy technologies.

Deployment Repeatability

Science.gov (United States)

2016-08-31

large cohort of trials to spot unusual cases. However, deployment repeatability is inherently a nonlinear phenomenon, which makes modeling difficult...and GEMS tip position were both tracked during ground testing by a laser target tracking system. Earlier SAILMAST testing in 2005 [8] used...recalls the strategy used by SRTM, where a constellation of lights was installed at the tip of the boom and a modified star tracker was used to track tip

Precise determination of the deuteron spin structure at low to moderate Q2 with CLAS and extraction of the neutron contribution

Science.gov (United States)

Guler, N.; Fersch, R. G.; Kuhn, S. E.; Bosted, P.; Griffioen, K. A.; Keith, C.; Minehart, R.; Prok, Y.; Adhikari, K. P.; Adikaram, D.; Amaryan, M. J.; Anderson, M. D.; Anefalos Pereira, S.; Avakian, H.; Ball, J.; Battaglieri, M.; Batourine, V.; Bedlinskiy, I.; Biselli, A.; Briscoe, W. J.; Brooks, W. K.; Bültmann, S.; Burkert, V. D.; Carman, D. S.; Celentano, A.; Chandavar, S.; Charles, G.; Colaneri, L.; Cole, P. L.; Contalbrigo, M.; Crabb, D.; Crede, V.; D'Angelo, A.; Dashyan, N.; Deur, A.; Djalali, C.; Dodge, G. E.; Dupre, R.; Alaoui, A. El; El Fassi, L.; Elouadrhiri, L.; Eugenio, P.; Fedotov, G.; Fegan, S.; Filippi, A.; Fleming, J. A.; Forest, T. A.; Garillon, B.; Garçon, M.; Gevorgyan, N.; Gilfoyle, G. P.; Giovanetti, K. L.; Girod, F. X.; Goetz, J. T.; Golovatch, E.; Gothe, R. W.; Guidal, M.; Guo, L.; Hafidi, K.; Hakobyan, H.; Harrison, N.; Hattawy, M.; Hicks, K.; Ho, D.; Holtrop, M.; Hughes, S. M.; Hyde, C. E.; Ireland, D. G.; Ishkhanov, B. S.; Isupov, E. L.; Jo, H. S.; Joo, K.; Joosten, S.; Keller, D.; Khandaker, M.; Kim, A.; Kim, W.; Klein, A.; Klein, F. J.; Kubarovsky, V.; Kuleshov, S. V.; Livingston, K.; Lu, H. Y.; Mayer, M.; MacGregor, I. J. D.; McKinnon, B.; Mirazita, M.; Mokeev, V.; Montgomery, R. A.; Movsisyan, A.; Munoz Camacho, C.; Nadel-Turonski, P.; Net, L. A.; Niculescu, I.; Osipenko, M.; Ostrovidov, A. I.; Park, K.; Pasyuk, E.; Pisano, S.; Pogorelko, O.; Price, J. W.; Procureur, S.; Ripani, M.; Rizzo, A.; Rosner, G.; Rossi, P.; Roy, P.; Sabatié, F.; Salgado, C.; Schott, D.; Schumacher, R. A.; Seder, E.; Simonyan, A.; Skorodumina, Iu.; Sokhan, D.; Sparveris, N.; Strakovsky, I. I.; Strauch, S.; Sytnik, V.; Tian, Ye; Tkachenko, S.; Ungaro, M.; Voutier, E.; Walford, N. K.; Wei, X.; Weinstein, L. B.; Wood, M. H.; Zachariou, N.; Zana, L.; Zhang, J.; Zhao, Z. W.; Zonta, I.; CLAS Collaboration

2015-11-01

We present the final results for the deuteron spin structure functions obtained from the full data set collected in 2000-2001 with Jefferson Lab's continuous electron beam accelerator facility (CEBAF) using the CEBAF large acceptance spectrometer (CLAS). Polarized electrons with energies of 1.6, 2.5, 4.2, and 5.8 GeV were scattered from deuteron (15ND3 ) targets, dynamically polarized along the beam direction, and detected with CLAS. From the measured double-spin asymmetry, the virtual photon absorption asymmetry A1d and the polarized structure function g1d were extracted over a wide kinematic range (0.05 GeV2structure functions A1n and g1n of the (bound) neutron, which are so far unknown in the resonance region, W <2 GeV. We compare our final results, including several moments of the deuteron and neutron spin structure functions, with various theoretical models and expectations, as well as parametrizations of the world data. The unprecedented precision and dense kinematic coverage of these data can aid in future extractions of polarized parton distributions, tests of perturbative QCD predictions for the quark polarization at large x , a better understanding of quark-hadron duality, and more precise values for higher-twist matrix elements in the framework of the operator product expansion.

Experiences and career intentions of combat-deployed UK military personnel.

Science.gov (United States)

Morris-Butler, R; Jones, N; Greenberg, N; Campion, B; Wessely, S

2018-05-17

Most studies of the psychological impact of military deployment focus on the negative and traumatic aspects. Less is known about the full range of deployment experiences nor how these may impact on career intentions. To examine subjective operational experiences and career intentions in deployed UK military personnel using data gathered toward the end of an operational deployment. Data were gathered during deployment in Iraq and Afghanistan. A self-report survey collected data on sociodemographic, operational and military factors. Respondents provided their strength of agreement or disagreement with six potentially positive deployment experiences and their endorsement or rejection of six possible career intentions. Two mental health measures assessed symptoms of common mental disorder and post-traumatic stress disorder. Responses were 681 in Iran 2009 (100% response rate); 1421 in Afghanistan in 2010 (100%), 1362 in 2011 (96%) and 860 in 2015 (91%). Five of the potentially positive outcomes were endorsed by >50% of the sample: confidence about remaining healthy after returning home, pride in accomplishments, increased confidence in abilities, improved unit cohesion and experiencing a positive life effect. Ninety per cent of respondents planned to continue in service after returning home. Fewer positive deployment experiences, poorer mental health, lesser unit cohesion and more negative impressions of leadership were significantly associated with intention to leave service. Contrary to the popular belief that UK military personnel deployed to Iraq or Afghanistan experience negative outcomes, this paper shows that deployment can be a positive experience for a substantial majority of deployed personnel.

Applications of Dynamic Deployment of Services in Industrial Automation

Science.gov (United States)

Candido, Gonçalo; Barata, José; Jammes, François; Colombo, Armando W.

Service-oriented Architecture (SOA) is becoming a de facto paradigm for business and enterprise integration. SOA is expanding into several domains of application envisioning a unified solution suitable across all different layers of an enterprise infrastructure. The application of SOA based on open web standards can significantly enhance the interoperability and openness of those devices. By embedding a dynamical deployment service even into small field de- vices, it would be either possible to allow machine builders to place built- in services and still allow the integrator to deploy on-the-run the services that best fit his current application. This approach allows the developer to keep his own preferred development language, but still deliver a SOA- compliant application. A dynamic deployment service is envisaged as a fundamental framework to support more complex applications, reducing deployment delays, while increasing overall system agility. As use-case scenario, a dynamic deployment service was implemented over DPWS and WS-Management specifications allowing designing and programming an automation application using IEC61131 languages, and deploying these components as web services into devices.

Using Deduplicating Storage for Efficient Disk Image Deployment

Directory of Open Access Journals (Sweden)

Xing Lin

2015-08-01

Full Text Available Many clouds and network testbeds use disk images to initialize local storage on their compute devices. Large facilities must manage thousands or more images, requiring significant amounts of storage. At the same time, to provide a good user experience, they must be able to deploy those images quickly. Driven by our experience in operating the Emulab site at the University of Utah---a long-lived and heavily-used testbed---we have created a new service for efficiently storing and deploying disk images. This service exploits the redundant data found in similar images, using deduplication to greatly reduce the amount of physical storage required. In addition to space savings, our system is also designed for highly efficient image deployment---it integrates with an existing highly-optimized disk image deployment system, Frisbee, without significantly increasing the time required to distribute and install images. In this paper, we explain the design of our system and discuss the trade-offs we made to strike a balance between efficient storage and fast disk image deployment. We also propose a new chunking algorithm, called AFC, which enables fixed-size chunking for deduplicating allocated disk sectors. Experimental results show that our system reduces storage requirements by up to 3x while imposing only a negligible runtime overhead on the end-to-end disk-deployment process.

Timing and structure of the penultimate deglaciation in north China constrained by a precisely dated stalagmite record

Science.gov (United States)

Duan, W.; Cheng, H.; Tan, M.; Li, X.; Edwards, R. L.

2017-12-01

The timing and structure of the penultimate deglaciation (Termination II, T-II) is still controversial due to the lack of precise-date and high-resolution paleoclimate documents. This study firstly presents high-precision stalagmite δ18O data encompassing T-II from north China, near the northern limit of the East Asian summer monsoon (EASM), an area sensitive to climate change. An obvious 2200-year long 18O-depleted excursion was identified within T-II, 1500 years later than in south China, mostly indicating it's a hitherto unidentified interstadial event, but the possibility of a local signal linked to karst hydrologic changes cannot be excluded. The sharpest T-II transition occurred at 129.20 ka BP (BP=before AD 1950), consistent with other EASM records but 3000 years later than mid-high-latitudinal cave records in Europe and North America. The different ages between them are attributed to that the original ice sheet melting during T-II did not inhibit the overturning in the Nordic Seas, leaving the heat transport to western Europe unaffected. Furthermore, the rise in EASM after the main T-II transition was interrupted by a significant "pause" in our record, whereas only expressed as a "slowdown" in south Chinese caves, further confirming the higher sensitivity of climate in north China. Compared with the last deglaciation (T-I), this climate pause could be considered as a Younger Dryas (YD)-type event that was shifted into the early stage of the last interglacial period, though its intensity and duration were not as strong as the YD during T-I. Key words: North China stalagmite record Timing and structure Termination II

Autonomous Deployment and Restoration of Sensor Network using Mobile Robots

Directory of Open Access Journals (Sweden)

Tsuyoshi Suzuki

2010-09-01

Full Text Available This paper describes an autonomous deployment and restoration of a Wireless Sensor Network (WSN using mobile robots. The authors have been developing an information-gathering system using mobile robots and WSNs in underground spaces in post-disaster environments. In our system, mobile robots carry wireless sensor nodes (SN and deploy them into the environment while measuring Received Signal Strength Indication (RSSI values to ensure communication, thereby enabling the WSN to be deployed and restored autonomously. If the WSN is disrupted, mobile robots restore the communication route by deploying additional or alternate SNs to suitable positions. Utilizing the proposed method, a mobile robot can deploy a WSN and gather environmental information via the WSN. Experimental results using a verification system equipped with a SN deployment and retrieval mechanism are presented.

Autonomous Deployment and Restoration of Sensor Network using Mobile Robots

Directory of Open Access Journals (Sweden)

Tsuyoshi Suzuki

2010-06-01

Full Text Available This paper describes an autonomous deployment and restoration of a Wireless Sensor Network (WSN using mobile robots. The authors have been developing an information-gathering system using mobile robots and WSNs in underground spaces in post-disaster environments. In our system, mobile robots carry wireless sensor nodes (SN and deploy them into the environment while measuring Received Signal Strength Indication (RSSI values to ensure communication, thereby enabling the WSN to be deployed and restored autonomously. If the WSN is disrupted, mobile robots restore the communication route by deploying additional or alternate SNs to suitable positions. Utilizing the proposed method, a mobile robot can deploy a WSN and gather environmental information via the WSN. Experimental results using a verification system equipped with a SN deployment and retrieval mechanism are presented.

Deployment Algorithms of Wireless Sensor Networks for Near-surface Underground Oil and Gas Pipeline Monitoring

Directory of Open Access Journals (Sweden)

Hua-Ping YU

2014-07-01

Full Text Available Oil and gas pipelines are the infrastructure of national economic development. Deployment problem of wireless underground sensor networks (WUSN for oil and gas pipeline systems is a fundamental problem. This paper firstly analyzed the wireless channel characteristics and energy consumption model in near-surface underground soil, and then studied the spatial structure of oil and gas pipelines and introduced the three-layer system structure of WUSN for oil and gas pipelines monitoring. Secondly, the optimal deployment strategy in XY plane and XZ plane which were projected from three-dimensional oil and gas pipeline structure was analyzed. Thirdly, the technical framework of using kinetic energy of the fluid in pipelines to recharge sensor nodes and partition strategy for energy consumption balance based on the wireless communication technology of magnetic induction waveguide were proposed, which can effectively improve the energy performance and connectivity of the network, and provide theoretical guidance and practical basis for the monitoring of long oil and gas pipeline network, the city tap water pipe network and sewage pipe network.

Morphologies of precise polyethylene-based acid copolymers and ionomers

Science.gov (United States)

Buitrago, C. Francisco

Acid copolymers and ionomers are polymers that contain a small fraction of covalently bound acidic or ionic groups, respectively. For the specific case of polyethylene (PE), acid and ionic pendants enhance many of the physical properties such as toughness, adhesion and rheological properties. These improved properties result from microphase separated aggregates of the polar pendants in the non-polar PE matrix. Despite the widespread industrial use of these materials, rigorous chemical structure---morphology---property relationships remain elusive due to the inevitable structural heterogeneities in the historically-available acid copolymers and ionomers. Recently, precise acid copolymers and ionomers were successfully synthesized by acyclic diene metathesis (ADMET) polymerization. These precise materials are linear, high molecular weight PEs with pendant acid or ionic functional groups separated by a precisely controlled number of carbon atoms. The morphologies of nine precise acid copolymers and eleven precise ionomers were investigated by X-ray scattering, solid-state 13C nuclear magnetic resonance (NMR) and differential scanning calorimetry (DSC). For comparison, the morphologies of linear PEs with pseudo-random placement of the pendant groups were also studied. Previous studies of precise copolymers with acrylic acid (AA) found that the microstructural precision produces a new morphology in which PE crystals drive the acid aggregates into layers perpendicular to the chain axes and presumably at the interface between crystalline and amorphous phases. In this dissertation, a second new morphology for acid copolymers is identified in which the aggregates arrange on cubic lattices. The fist report of a cubic morphology was observed at room and elevated temperatures for a copolymer functionalized with two phosphonic acid (PA) groups on every 21st carbon atom. The cubic lattice has been identified as face-centered cubic (FCC). Overall, three morphology types have been

Deploying HEP applications using Xen and Globus Virtual Workspaces

International Nuclear Information System (INIS)

Agarwal, A; Desmarais, R; Gable, I; Grundy, D; P-Brown, D; Seuster, R; Vanderster, D C; Sobie, R; Charbonneau, A; Enge, R

2008-01-01

The deployment of HEP applications in heterogeneous grid environments can be challenging because many of the applications are dependent on specific OS versions and have a large number of complex software dependencies. Virtual machine monitors such as Xen could be used to package HEP applications, complete with their execution environments, to run on resources that do not meet their operating system requirements. Our previous work has shown HEP applications running within Xen suffer little or no performance penalty as a result of virtualization. However, a practical strategy is required for remotely deploying, booting, and controlling virtual machines on a remote cluster. One tool that promises to overcome the deployment hurdles using standard grid technology is the Globus Virtual Workspaces project. We describe strategies for the deployment of Xen virtual machines using Globus Virtual Workspace middleware that simplify the deployment of HEP applications

Design of the De-Orbit Sail Boom Deployment Unit

Science.gov (United States)

Meyer, Sebastian; Hillebrandt, Martin; Straubel, Marco; Huhne, Christian

2014-06-01

The design of the De-Orbit Sail boom deployment unit is strongly driven by volume constraints, which are given by the cubesat container. Four CFRP (carbon fiber reinforced polymer) booms [4] with a cross-sectional shape of a double-omega and a length of 3.6 m are reeled on one spool in the center of the unit. The deployment of the four booms are controlled by an electric motor, which acts on the boom spool. Due to the volume limitation caused by the dimensions of the cubesat deployer the deployment unit has little room for the mechanisms components. With the aim to achieve a robust design, the deployment concept of the unit has greatly changed during the development process. The history of the design as well as the mechanisms are described. Additionally the results of the flight model testing are presented.

Perceived effect of deployment on families of UK military personnel.

Science.gov (United States)

Thandi, G; Greenberg, N; Fear, N T; Jones, N

2017-10-01

In the UK, little is known about the perceived effects of deployment, on military families, from military personnel in theatre. To investigate military personnel's perceptions of the impact of deployment on intimate relationships and children. Deployed service personnel who were in a relationship, and who had children, completed a survey while deployed on combat operations. Data were taken from four mental health surveys carried out in Iraq in 2009 and Afghanistan in 2010, 2011 and 2014. Among 4265 participants, after adjusting for military and social-demographic covariates, perceiving that deployment had a negative impact on intimate relationships and children was associated with psychological distress, and traumatic stress symptoms. Military personnel who reported being in danger of being injured or killed during deployment, were more likely to report a perceived negative effect of deployment on their intimate relationships. Reservists were less likely to report a perceived negative impact of deployment on their children compared with regulars. Military personnel who themselves planned to separate from their partner were more likely to report psychological distress, and stressors at home. Perceived insufficient support from the Ministry of Defence was associated with poor mental health, and holding a junior rank. Deployed UK military personnel with symptoms of psychological distress, who experienced stressors at home, were especially likely to perceive that their family were inadequately supported by the military. Those planning to separate from their partner were at increased risk of suffering with mental health problems while deployed. © The Author 2017. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com

Development of millimeter-wave accelerating structures using precision metal forming technology

Energy Technology Data Exchange (ETDEWEB)

None

2003-06-03

High gradients in radio-frequency (RF) driven accelerators require short wavelengths that have the concomitant requirements of small feature size and high tolerances, 1-2 {micro}m for millimeter wavelengths. Precision metal-forming stampling has the promise of meeting those tolerances with high production rates. This STI will evaluate that promise.

Mechanical properties and cell-culture characteristics of a polycaprolactone kagome-structure scaffold fabricated by a precision extruding deposition system.

Science.gov (United States)

Lee, Se-Hwan; Cho, Yong Sang; Hong, Myoung Wha; Lee, Bu-Kyu; Park, Yongdoo; Park, Sang-Hyug; Kim, Young Yul; Cho, Young-Sam

2017-09-13

To enhance the mechanical properties of three-dimensional (3D) scaffolds used for bone regeneration in tissue engineering, many researchers have studied their structure and chemistry. In the structural engineering field, the kagome structure has been known to have an excellent relative strength. In this study, to enhance the mechanical properties of a synthetic polymer scaffold used for tissue engineering, we applied the 3D kagome structure to a porous scaffold for bone regeneration. Prior to fabricating the biocompatible-polymer scaffold, the ideal kagome structure, which was manufactured by a 3D printer of the digital light processing type, was compared with a grid-structure, which was used as the control group, using a compressive experiment. A polycaprolactone (PCL) kagome-structure scaffold was successfully fabricated by additive manufacturing using a 3D printer with a precision extruding deposition head. To assess the physical characteristics of the fabricated PCL-kagome-structure scaffold, we analyzed its porosity, pore size, morphological structure, surface roughness, compressive stiffness, and mechanical bending properties. The results showed that, the mechanical properties of proposed kagome-structure scaffold were superior to those of a grid-structure scaffold. Moreover, Sarcoma osteogenic (Saos-2) cells were used to evaluate the characteristics of in vitro cell proliferation. We carried out cell counting kit-8 (CCK-8) and DNA contents assays. Consequently, the cell proliferation of the kagome-structure scaffold was increased; this could be because the surface roughness of the kagome-structure scaffold enhances initial cell attachment.

Deployment of Mobile Learning Course Materials to Android Powered Mobile Devices

Science.gov (United States)

Chao, Lee

2012-01-01

The objective of this article is to facilitate mobile teaching and learning by providing an alternative course material deployment method. This article suggests a course material deployment platform for small universities or individual instructors. Different from traditional course material deployment methods, the method discussed deploys course…

The financial impact of deployments on reserve health care providers.

Science.gov (United States)

Petinaux, Bruno

2008-08-01

This study retrospectively surveyed the financial impact of deployments on 17 U.S. Army Reserve health care providers. Due to multiple mobilizations, 29 separate deployments were reported. The deployments, mostly between 2001 and 2005, typically lasted 3 months during which 86% reported no civilian income and 76% reported no civilian benefits. Solo practice providers reported the greatest financial losses due to continuing financial responsibility related to their civilian practice despite being deployed. Overall, 2 deployments did not change, 9 increased, and 16 decreased the medical officer's income. Two were not reported. In this small retrospective convenience sample study, solo practice U.S. Army Reserve health care providers were found to be at highest risk of financial losses during military deployments. This being said, no price can be put on the privilege of serving our men and women in uniform.

A precise determination of the nucleon structure functions in charged-current interactions on an iron target

International Nuclear Information System (INIS)

Vallage, B.

1987-01-01

570 000 neutrino-iron and 370 000 antineutrino-iron charged-current events were obtained from the Wide Band Beam exposure of the CDHS detector at CERN in 1983, at energies ranging from 20 to 400 GeV. These large statistics allowed a precise measurement of the charged-current differential cross-sections and a detailed study of systematic effects. The nucleon structure functions have been determined in the framework of the quark-parton model, in the kinematic range: 0.015 2 2 /c 2 . The longitudinal structure function F L (x) is in good agreement with the QCD predicted shape. Deviations from scale invariance are clearly seen from the functions F 2 and xF 3 . The Q 2 evolution of the valence quark distribution has been compared with the QCD prediction in order to measure the scale parameter Λ. A good agreement is obtained only if the low Q 2 points are removed from the comparison. Our experiment favours a value of Λ between 50 and 250 MeV [fr

DRAGON - 8U Nanosatellite Orbital Deployer

Science.gov (United States)

Dobrowolski, Marcin; Grygorczuk, Jerzy; Kedziora, Bartosz; Tokarz, Marta; Borys, Maciej

2014-01-01

The Space Research Centre of the Polish Academy of Sciences (SRC PAS) together with Astronika company have developed an Orbital Deployer called DRAGON for ejection of the Polish scientific nanosatellite BRITE-PL Heweliusz (Fig. 1). The device has three unique mechanisms including an adopted and scaled lock and release mechanism from the ESA Rosetta mission MUPUS instrument. This paper discusses major design restrictions of the deployer, unique design features, and lessons learned from development through testing.

RSOI: Force Deployment Bottleneck

National Research Council Canada - National Science Library

D'Amato, Mark

1998-01-01

.... This runs counter to the popular belief that strategic lift is the limiting constraint. The study begins by highlighting the genesis of the military's current force projection strategy and the resulting importance of rapid force deployments...

Deploying Embodied AI into Virtual Worlds

Science.gov (United States)

Burden, David J. H.

The last two years have seen the start of commercial activity within virtual worlds. Unlike computer games where Non-Player-Character avatars are common, in most virtual worlds they are the exception — and until recently in Second Life they were non-existent. However there is real commercial scope for Als in these worlds — in roles from virtual sales staff and tutors to personal assistants. Deploying an embodied AI into a virtual world offers a unique opportunity to evaluate embodied Als, and to develop them within an environment where human and computer are on almost equal terms. This paper presents an architecture being used for the deployment of chatbot driven avatars within the Second Life virtual world, looks at the challenges of deploying an AI within such a virtual world, the possible implications for the Turing Test, and identifies research directions for the future.

Abstracting application deployment on Cloud infrastructures

Science.gov (United States)

Aiftimiei, D. C.; Fattibene, E.; Gargana, R.; Panella, M.; Salomoni, D.

2017-10-01

Deploying a complex application on a Cloud-based infrastructure can be a challenging task. In this contribution we present an approach for Cloud-based deployment of applications and its present or future implementation in the framework of several projects, such as “!CHAOS: a cloud of controls” [1], a project funded by MIUR (Italian Ministry of Research and Education) to create a Cloud-based deployment of a control system and data acquisition framework, “INDIGO-DataCloud” [2], an EC H2020 project targeting among other things high-level deployment of applications on hybrid Clouds, and “Open City Platform”[3], an Italian project aiming to provide open Cloud solutions for Italian Public Administrations. We considered to use an orchestration service to hide the complex deployment of the application components, and to build an abstraction layer on top of the orchestration one. Through Heat [4] orchestration service, we prototyped a dynamic, on-demand, scalable platform of software components, based on OpenStack infrastructures. On top of the orchestration service we developed a prototype of a web interface exploiting the Heat APIs. The user can start an instance of the application without having knowledge about the underlying Cloud infrastructure and services. Moreover, the platform instance can be customized by choosing parameters related to the application such as the size of a File System or the number of instances of a NoSQL DB cluster. As soon as the desired platform is running, the web interface offers the possibility to scale some infrastructure components. In this contribution we describe the solution design and implementation, based on the application requirements, the details of the development of both the Heat templates and of the web interface, together with possible exploitation strategies of this work in Cloud data centers.

49 CFR 268.3 - Different phases of the Maglev Deployment Program.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Different phases of the Maglev Deployment Program... DEPLOYMENT PROGRAM Overview § 268.3 Different phases of the Maglev Deployment Program. (a) The Maglev... deadlines—based on the progress of the Maglev Deployment Program; grantees will be notified accordingly. (b...

Modeling applications for precision agriculture in the California Central Valley

Science.gov (United States)

Marklein, A. R.; Riley, W. J.; Grant, R. F.; Mezbahuddin, S.; Mekonnen, Z. A.; Liu, Y.; Ying, S.

2017-12-01

Drought in California has increased the motivation to develop precision agriculture, which uses observations to make site-specific management decisions throughout the growing season. In agricultural systems that are prone to drought, these efforts often focus on irrigation efficiency. Recent improvements in soil sensor technology allow the monitoring of plant and soil status in real-time, which can then inform models aimed at improving irrigation management. But even on farms with resources to deploy soil sensors across the landscape, leveraging that sensor data to design an efficient irrigation scheme remains a challenge. We conduct a modeling experiment aimed at simulating precision agriculture to address several questions: (1) how, when, and where does irrigation lead to optimal yield? and (2) What are the impacts of different precision irrigation schemes on yields, soil organic carbon (SOC), and total water use? We use the ecosys model to simulate precision agriculture in a conventional tomato-corn rotation in the California Central Valley with varying soil water content thresholds for irrigation and soil water sensor depths. This model is ideal for our question because it includes explicit process-based functions for the plant growth, plant water use, soil hydrology, and SOC, and has been tested extensively in agricultural ecosystems. Low irrigation thresholds allows the soil to become drier before irrigating compared to high irrigation thresholds; as such, we found that the high irrigation thresholds use more irrigation over the course of the season, have higher yields, and have lower water use efficiency. The irrigation threshold did not affect SOC. Yields and water use are highest at sensor depths of 0.5 to 0.15 m, but water use efficiency was also lowest at these depths. We found SOC to be significantly affected by sensor depth, with the highest SOC at the shallowest sensor depths. These results will help regulate irrigation water while maintaining yield

An ARM Mobile Facility Designed for Marine Deployments

Science.gov (United States)

Wiscombe, W. J.

2007-05-01

The U.S. Dept. of Energy's ARM (Atmospheric Radiation Measurements) Program is designing a Mobile Facility exclusively for marine deployments. This marine facility is patterned after ARM's land Mobile Facility, which had its inaugural deployment at Point Reyes, California, in 2005, followed by deployments to Niger in 2006 and Germany in 2007 (ongoing), and a planned deployment to China in 2008. These facilities are primarily intended for the study of clouds, radiation, aerosols, and surface processes with a goal to include these processes accurately in climate models. They are preferably embedded within larger field campaigns which provide context. They carry extensive instrumentation (in several large containers) including: cloud radar, lidar, microwave radiometers, infrared spectrometers, broadband and narrowband radiometers, sonde-launching facilities, extensive surface aerosol measurements, sky imagers, and surface latent and sensible heat flux devices. ARM's Mobile Facilities are designed for 6-10 month deployments in order to capture climatically-relevant datasets. They are available to any scientist, U.S. or international, who wishes to submit a proposal during the annual Spring call. The marine facility will be adapted to, and ruggedized for, the harsh marine environment and will add a scanning two-frequency radar, a boundary-layer wind profiler, a shortwave spectrometer, and aerosol instrumentation adapted to typical marine aerosols like sea salt. Plans also include the use of roving small UAVs, automated small boats, and undersea autonomous vehicles in order to address the point-to-area-average problem which is so crucial for informing climate models. Initial deployments are planned for small islands in climatically- interesting cloud regimes, followed by deployments on oceanic platforms (like decommissioned oil rigs and the quasi-permanent platform of this session's title) and eventually on large ships like car carriers plying routine routes.

Modeling EERE deployment programs

Energy Technology Data Exchange (ETDEWEB)

Cort, K. A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hostick, D. J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Belzer, D. B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Livingston, O. V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2007-11-01

The purpose of the project was to identify and characterize the modeling of deployment programs within the EERE Technology Development (TD) programs, address possible improvements to the modeling process, and note gaps in knowledge for future research.

High precision, low disturbance calibration of the High Voltage system of the CMS Barrel Electromagnetic Calorimeter

CERN Document Server

Fasanella, Giuseppe

2017-01-01

The CMS Electromagnetic Calorimeter utilizes scintillating lead tungstate crystals, with avalanche photodiodes (APD) as photo-detectors in the barrel part. 1224 HV channels bias groups of 50 APD pairs, each at a voltage of about 380 V. The APD gain dependence on the voltage is 3pct/V. A stability of better than 60 mV is needed to have negligible impact on the calorimeter energy resolution. Until 2015 manual calibrations were performed yearly. A new calibration system was deployed recently, which satisfies the requirement of low disturbance and high precision. The system is discussed in detail and first operational experience is presented.

High precision, low disturbance calibration of the High Voltage system of the CMS Barrel Electromagnetic Calorimeter

CERN Document Server

Fasanella, Giuseppe

2016-01-01

The CMS Electromagnetic Calorimeter utilizes scintillating lead tungstate crystals, with avalanche photodiodes (APD) as photo-detectors in the barrel part. 1224 HV channels bias groups of 50 APD pairs, each at a voltage of about 380 V. The APD gain dependence on the voltage is 3pct/V. A stability of better than 60 mV is needed to have negligible impact on the calorimeter energy resolution. Until 2015 manual calibrations were performed yearly. A new calibration system was deployed recently, which satisfies the requirement of low disturbance and high precision. The system is discussed in detail and first operational experience is presented.

High-Precision Computation: Mathematical Physics and Dynamics

International Nuclear Information System (INIS)

Bailey, D.H.; Barrio, R.; Borwein, J.M.

2010-01-01

At the present time, IEEE 64-bit oating-point arithmetic is suficiently accurate for most scientic applications. However, for a rapidly growing body of important scientic computing applications, a higher level of numeric precision is required. Such calculations are facilitated by high-precision software packages that include high-level language translation modules to minimize the conversion e ort. This pa- per presents a survey of recent applications of these techniques and provides someanalysis of their numerical requirements. These applications include supernova simulations, climate modeling, planetary orbit calculations, Coulomb n-body atomic systems, studies of the one structure constant, scattering amplitudes of quarks, glu- ons and bosons, nonlinear oscillator theory, experimental mathematics, evaluation of orthogonal polynomials, numerical integration of ODEs, computation of periodic orbits, studies of the splitting of separatrices, detection of strange nonchaotic at- tractors, Ising theory, quantum held theory, and discrete dynamical systems. We conclude that high-precision arithmetic facilities are now an indispensable compo- nent of a modern large-scale scientic computing environment.

High-Precision Computation: Mathematical Physics and Dynamics

Energy Technology Data Exchange (ETDEWEB)

Bailey, D. H.; Barrio, R.; Borwein, J. M.

2010-04-01

At the present time, IEEE 64-bit oating-point arithmetic is suficiently accurate for most scientic applications. However, for a rapidly growing body of important scientic computing applications, a higher level of numeric precision is required. Such calculations are facilitated by high-precision software packages that include high-level language translation modules to minimize the conversion e ort. This pa- per presents a survey of recent applications of these techniques and provides someanalysis of their numerical requirements. These applications include supernova simulations, climate modeling, planetary orbit calculations, Coulomb n-body atomic systems, studies of the one structure constant, scattering amplitudes of quarks, glu- ons and bosons, nonlinear oscillator theory, experimental mathematics, evaluation of orthogonal polynomials, numerical integration of ODEs, computation of periodic orbits, studies of the splitting of separatrices, detection of strange nonchaotic at- tractors, Ising theory, quantum held theory, and discrete dynamical systems. We conclude that high-precision arithmetic facilities are now an indispensable compo- nent of a modern large-scale scientic computing environment.

Keys to successful D and D technology deployments at the INEEL

International Nuclear Information System (INIS)

Smith, A.M.; Meservey, R. H.; Shoemaker, H.

2000-01-01

Seven improved decontamination and decommissioning (DandD) technologies were successfully deployed at the Idaho National Engineering and Environmental Laboratory (INEEL) during the Accelerated Site Technology Deployment (ASTD) Integrated Decontamination and Decommissioning (IDandD) project. The use of these improved technologies saved the INEEL $462K in fiscal year 1999, and is projected to save about $14M over the next ten years. Since deploying new technologies on DandD projects shows great potential for cost-savings, factors that led to successful deployment have been documented. These factors are described here as they apply to the seven deployments at the INEEL to assist with deployments at other DOE sites

Infrastructure Engineering and Deployment Division

Data.gov (United States)

Federal Laboratory Consortium — Volpe's Infrastructure Engineering and Deployment Division advances transportation innovation by being leaders in infrastructure technology, including vehicles and...

STEP flight experiments Large Deployable Reflector (LDR) telescope

Science.gov (United States)

Runge, F. C.

1984-01-01

Flight testing plans for a large deployable infrared reflector telescope to be tested on a space platform are discussed. Subsystem parts, subassemblies, and whole assemblies are discussed. Assurance of operational deployability, rigidization, alignment, and serviceability will be sought.

The Feasibility of Quality Function Deployment (QFD) as an Assessment and Quality Assurance Model

Science.gov (United States)

Matorera, D.; Fraser, W. J.

2016-01-01

Business schools are globally often seen as structured, purpose-driven, multi-sector and multi-perspective organisations. This article is based on the response of a graduate school to an innovative industrial Quality Function Deployment-based model (QFD), which was to be adopted initially in a Master's degree programme for quality assurance…

Research and development of a technology to create original high-function materials in fiscal 1998 (development of precision structure controlling materials by improving petroleum refining). Report on achievements in research and development of precision catalytic polymerization; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho. Sekiyu seisei kodoka seimitsu kozo seigyo zairyo kaihatsu (seimitsu shokubai jugo no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Research and development on precision catalytic polymerization aims at developing polymerizing catalysts that can control arbitrarily the molecular weight and three-dimensional regularity by which rapid enhancement can be expected in performance of additional polymerization type polymers, and the primary structure of terminal groups. Works are being done on two sub-themes of ultimate additional polymerization and orientation catalyst polymerization. The research and development of the ultimate additional polymerization included structural control in polymerization reaction in vinyl chloride, vinylester and acrylic monomers, radical polymerization with precision orientation control, anionic polymerization with precision structural control, and precision polymerization utilizing asymmetric metal porphyrin complexes. In the research and development of the orientation catalyst polymerization, the orientation catalyst polymerization was researched and developed, elementary reaction of metallocene was elucidated, high-performance carrier catalysts were developed, advanced function polymers were synthesized at high precision based on metathesis, and improvement of functions of polyolefin was researched and developed. Surveys and studies were carried out on fundamental technologies common to the above two themes re-commissioned to five universities. (NEDO)

Pneumothorax, without chest wall fracture, following airbag deployment

Directory of Open Access Journals (Sweden)

Samuel Parsons

2010-12-01

Full Text Available Air bags are an automatic crash protection system. They have been shown to reduce mortality from motor vehicle accidents by 31% following direct head-on impacts, by 19% following any frontal impact and by 11% overall. Despite obvious benefits there has been a corresponding increase in the number of injuries resulting from their deployment. We describe a case of a pneumothorax in the absence of chest wall pathology associated with airbag deployment, in a belted driver. There has been one previous description of pneumothorax associated with airbag deployment, in an unbelted driver.

Treatment Deployment Evaluation Tool

International Nuclear Information System (INIS)

M. A. Rynearson; M. M. Plum

1999-01-01

The U.S. Department of Energy (DOE) is responsible for the final disposition of legacy spent nuclear fuel (SNF). As a response, DOE's National Spent Nuclear Fuel Program (NSNFP) has been given the responsibility for the disposition of DOE-owned SNF. Many treatment technologies have been identified to treat some forms of SNF so that the resulting treated product is acceptable by the disposition site. One of these promising treatment processes is the electrometallurgical treatment (EMT) currently in development; a second is an Acid Wash Decladding process. The NSNFP has been tasked with identifying possible strategies for the deployment of these treatment processes in the event that a treatment path is deemed necessary. To support the siting studies of these strategies, economic evaluations are being performed to identify the least-cost deployment path. This model (tool) was developed to consider the full scope of costs, technical feasibility, process material disposition, and schedule attributes over the life of each deployment alternative. Using standard personal computer (PC) software, the model was developed as a comprehensive technology economic assessment tool using a Life-Cycle Cost (LCC) analysis methodology. Model development was planned as a systematic, iterative process of identifying and bounding the required activities to dispose of SNF. To support the evaluation process, activities are decomposed into lower level, easier to estimate activities. Sensitivity studies can then be performed on these activities, defining cost issues and testing results against the originally stated problem

Precision medicine in myasthenia graves: begin from the data precision

Science.gov (United States)

Hong, Yu; Xie, Yanchen; Hao, Hong-Jun; Sun, Ren-Cheng

2016-01-01

Myasthenia gravis (MG) is a prototypic autoimmune disease with overt clinical and immunological heterogeneity. The data of MG is far from individually precise now, partially due to the rarity and heterogeneity of this disease. In this review, we provide the basic insights of MG data precision, including onset age, presenting symptoms, generalization, thymus status, pathogenic autoantibodies, muscle involvement, severity and response to treatment based on references and our previous studies. Subgroups and quantitative traits of MG are discussed in the sense of data precision. The role of disease registries and scientific bases of precise analysis are also discussed to ensure better collection and analysis of MG data. PMID:27127759

Precision Measurement of the Neutron Spin Asymmetries and Spin-dependent Structure Functions in the Valence Quark Region

International Nuclear Information System (INIS)

Xiaochao Zheng; Konrad Aniol; David Armstrong; Todd Averett; William Bertozzi; Sebastien Binet; Etienne Burtin; Emmanuel Busato; Cornel Butuceanu; John Calarco; Alexandre Camsonne; Gordon Cates; Zhengwei Chai; Jian-ping Chen; Seonho Choi; Eugene Chudakov; Francesco Cusanno; Raffaele De Leo; Alexandre Deur; Sonja Dieterich; Dipangkar Dutta; John Finn; Salvatore Frullani; Haiyan Gao; Juncai Gao; Franco Garibaldi; Shalev Gilad; Ronald Gilman; Javier Gomez; Jens-ole Hansen; Douglas Higinbotham; Wendy Hinton; Tanja Horn; Cornelis De Jager; Xiaodong Jiang; Lisa Kaufman; James Kelly; Wolfgang Korsch; Kevin Kramer; John Lerose; David Lhuillier; Nilanga Liyanage; Demetrius Margaziotis; Frederic Marie; Pete Markowitz; Kathy Mccormick; Zein-eddine Meziani; Robert Michaels; Bryan Moffit; Sirish Nanda; Damien Neyret; Sarah Phillips; Anthony Powell; Thierry Pussieux; Bodo Reitz; Julie Roche; Michael Roedelbronn; Guy Ron; Marat Rvachev; Arunava Saha; Nikolai Savvinov; Jaideep Singh; Simon Sirca; Karl Slifer; Patricia Solvignon; Paul Souder; Daniel Steiner; Steffen Strauch; Vincent Sulkosky; William Tobias; Guido Urciuoli; Antonin Vacheret; Bogdan Wojtsekhowski; Hong Xiang; Yuan Xiao; Feng Xiong; Bin Zhang; Lingyan Zhu; Xiaofeng Zhu; Piotr Zolnierczuk

2004-01-01

We report on measurements of the neutron spin asymmetries A 1,2 n and polarized structure functions g 1,2 n at three kinematics in the deep inelastic region, with x = 0.33, 0.47 and .60 and Q 2 = 2.7, 3.5 and 4.8 (GeV/c) 2 , respectively. These measurements were performed using a 5.7 GeV longitudinally-polarized electron beam and a polarized 3 He target. The results for A 1 n and g 1 n at x = 0.33 are consistent with previous world data and, at the two higher x points, have improved the precision of the world data by about an order of magnitude. The new A 1 n data show a zero crossing around x = 0.47 and the value at x = 0.60 is significantly positive. These results agree with a next-to-leading order QCD analysis of previous world data. The trend of data at high x agrees with constituent quark model predictions but disagrees with that from leading-order perturbative QCD (pQCD) assuming hadron helicity conservation. Results for A 2 n and g 2 n have a precision comparable to the best world data in this kinematic region. Combined with previous world data, the moment d 2 n was evaluated and the new result has improved the precision of this quantity by about a factor of two. When combined with the world proton data, polarized quark distribution functions were extracted from the new g 1 n /F 1 n values based on the quark parton model. While results for Δu/u agree well with predictions from various models, results for Δd/d disagree with the leading-order pQCD prediction when hadron helicity conservation is imposed

Reactor power system deployment and startup

International Nuclear Information System (INIS)

Wetch, J.R.; Nelin, C.J.; Britt, E.J.; Klein, G.; Rasor Associates, Inc., Sunnyvale, CA; California Institute of Technology, Pasadena)

1985-01-01

This paper addresses issues that should receive further examination in the near-term as concept selection for development of a U.S. space reactor power system is approached. The issues include: the economics, practicality and system reliability associated with transfer of nuclear spacecraft from low earth shuttle orbits to operational orbits, via chemical propulsion versus nuclear electric propulsion; possible astronaut supervised reactor and nuclear electric propulsion startup in low altitude Shuttle orbit; potential deployment methods for nuclear powered spacecraft from Shuttle; the general public safety of low altitude startup and nuclear safe and disposal orbits; the question of preferred reactor power level; and the question of frozen versus molten alkali metal coolant during launch and deployment. These issues must be considered now because they impact the SP-100 concept selection, power level selection, weight and size limits, use of deployable radiators, reliability requirements, and economics, as well as the degree of need for and the urgency of developing space reactor power systems. 5 references

High Gain Antenna System Deployment Mechanism Integration, Characterization, and Lessons Learned

Science.gov (United States)

Parong, Fil; Russell, Blair; Garcen, Walter; Rose, Chris; Johnson, Chris; Huber, Craig

2014-01-01

The integration and deployment testing of the High Gain Antenna System for the Global Precipitation Measurement mission is summarized. The HGAS deployment mechanism is described. The gravity negation system configuration and its influence on vertical, ground-based, deployment tests are presented with test data and model predictions. A focus is made on the late discovery and resolution of a potentially mission degrading deployment interference condition. The interaction of the flight deployment mechanism, gravity negation mechanism, and use of dynamic modeling is described and lessons learned presented.

Reintegration Difficulty of Military Couples Following Deployment

Science.gov (United States)

2017-07-01

reintegration. Communication and Generalized Anxiety The emotional cycle of deployment model provides a descrip- tive framework for understanding the...counseling. Thus, communication can have a reciprocal influence on the very appraisals and emotions that motivate interaction in the first place. Communication...of service members back into family life after deployment can be extremely challenging for military couples. Understanding the factors that

A space release/deployment system actuated by shape memory wires

Science.gov (United States)

Fragnito, Marino; Vetrella and, Sergio

2002-11-01

In this paper, the design of an innovative hold down/release and deployment device actuated by shape memory wires, to be used for the first time for the S MA RT microsatellite solar wings is shown. The release and deployment mechanisms are actuated by a Shape Memory wire (Nitinol), which allows a complete symmetrical and synchronous release, in a very short time, of the four wings in pairs. The hold down kinematic mechanism is preloaded to avoid vibration nonlinearities and unwanted deployment at launch. The deployment mechanism is a simple pulley system. The stiffness of the deployed panel-hinge system needs to be dimensioned in order to meet the on-orbit requirement for attitude control. One-way roller clutches are used to keep the panel at the desired angle during the mission. An ad hoc software has been developed to simulate both the release and deployment operations, coupling the SMA wire behavior with the system mechanics.

Precision machining commercialization

International Nuclear Information System (INIS)

1978-01-01

To accelerate precision machining development so as to realize more of the potential savings within the next few years of known Department of Defense (DOD) part procurement, the Air Force Materials Laboratory (AFML) is sponsoring the Precision Machining Commercialization Project (PMC). PMC is part of the Tri-Service Precision Machine Tool Program of the DOD Manufacturing Technology Five-Year Plan. The technical resources supporting PMC are provided under sponsorship of the Department of Energy (DOE). The goal of PMC is to minimize precision machining development time and cost risk for interested vendors. PMC will do this by making available the high precision machining technology as developed in two DOE contractor facilities, the Lawrence Livermore Laboratory of the University of California and the Union Carbide Corporation, Nuclear Division, Y-12 Plant, at Oak Ridge, Tennessee

Fixed-axis electric sail deployment dynamics analysis using hub-mounted momentum control

Science.gov (United States)

Fulton, JoAnna; Schaub, Hanspeter

2018-03-01

The deployment dynamics of a spin stabilized electric sail (E-sail) with a hub-mounted control actuator are investigated. Both radial and tangential deployment mechanisms are considered to take the electric sail from a post-launch stowed configuration to a fully deployed configuration. The tangential configuration assumes the multi-kilometer tethers are wound up on the exterior of the spacecraft hub, similar to yo-yo despinner configurations. The deployment speed is controlled through the hub rate. The radial deployment configuration assumes each tether is on its own spool. Here both the hub and spool rate are control variables. The sensitivity of the deployment behavior to E-sail length, maximum rate and tension parameters is investigated. A constant hub rate deployment is compared to a time varying hub rate that maintains a constant tether tension condition. The deployment time can be reduced by a factor of 2 or more by using a tension controlled deployment configuration.

Reference satellite selection method for GNSS high-precision relative positioning

Directory of Open Access Journals (Sweden)

Xiao Gao

2017-03-01

Full Text Available Selecting the optimal reference satellite is an important component of high-precision relative positioning because the reference satellite directly influences the strength of the normal equation. The reference satellite selection methods based on elevation and positional dilution of precision (PDOP value were compared. Results show that all the above methods cannot select the optimal reference satellite. We introduce condition number of the design matrix in the reference satellite selection method to improve structure of the normal equation, because condition number can indicate the ill condition of the normal equation. The experimental results show that the new method can improve positioning accuracy and reliability in precise relative positioning.

QCD Precision Measurements and Structure Function Extraction at a High Statistics, High Energy Neutrino Scattering Experiment: NuSOnG

International Nuclear Information System (INIS)

Adams, T.; Batra, P.; Bugel, Leonard G.; Camilleri, Leslie Loris; Conrad, Janet Marie; Fisher, Peter H.; Formaggio, Joseph Angelo; Karagiorgi, Georgia S.; )

2009-01-01

We extend the physics case for a new high-energy, ultra-high statistics neutrino scattering experiment, NuSOnG (Neutrino Scattering On Glass) to address a variety of issues including precision QCD measurements, extraction of structure functions, and the derived Parton Distribution Functions (PDFs). This experiment uses a Tevatron-based neutrino beam to obtain a sample of Deep Inelastic Scattering (DIS) events which is over two orders of magnitude larger than past samples. We outline an innovative method for fitting the structure functions using a parameterized energy shift which yields reduced systematic uncertainties. High statistics measurements, in combination with improved systematics, will enable NuSOnG to perform discerning tests of fundamental Standard Model parameters as we search for deviations which may hint of 'Beyond the Standard Model' physics

Industrial deployment of system engineering methods

CERN Document Server

Romanovsky, Alexander

2013-01-01

A formal method is not the main engine of a development process, its contribution is to improve system dependability by motivating formalisation where useful. This book summarizes the results of the DEPLOY research project on engineering methods for dependable systems through the industrial deployment of formal methods in software development. The applications considered were in automotive, aerospace, railway, and enterprise information systems, and microprocessor design.  The project introduced a formal method, Event-B, into several industrial organisations and built on the lessons learned to

Post-deployment usability evaluation of a radiology workstation

NARCIS (Netherlands)

Jorritsma, Wiard; Cnossen, Fokie; Dierckx, Rudi; Oudkerk, Matthijs; van Ooijen, Peter

2015-01-01

Objective To evaluate the usability of a radiology workstation after deployment in a hospital. Significance In radiology, it is difficult to perform valid pre-deployment usability evaluations due to the heterogeneity of the user group, the complexity of the radiological workflow, and the complexity

Hitting the ground running: Healthgrid deployment and adoption

NARCIS (Netherlands)

Gwadry-Sridhar, Femida; Olabarriaga, Silvia D.; van Kampen, Antoine; Bauer, Michael; Solomonides, Tony

2010-01-01

We consider the issues of healthgrid development, deployment and adoption in health care and research environments. While healthgrid technology could be deployed to support advanced medical research, we are not seeing its wide adoption. Understanding why this technology is not being exploited is one

Big Data's Role in Precision Public Health.

Science.gov (United States)

Dolley, Shawn

2018-01-01

Precision public health is an emerging practice to more granularly predict and understand public health risks and customize treatments for more specific and homogeneous subpopulations, often using new data, technologies, and methods. Big data is one element that has consistently helped to achieve these goals, through its ability to deliver to practitioners a volume and variety of structured or unstructured data not previously possible. Big data has enabled more widespread and specific research and trials of stratifying and segmenting populations at risk for a variety of health problems. Examples of success using big data are surveyed in surveillance and signal detection, predicting future risk, targeted interventions, and understanding disease. Using novel big data or big data approaches has risks that remain to be resolved. The continued growth in volume and variety of available data, decreased costs of data capture, and emerging computational methods mean big data success will likely be a required pillar of precision public health into the future. This review article aims to identify the precision public health use cases where big data has added value, identify classes of value that big data may bring, and outline the risks inherent in using big data in precision public health efforts.

Elastic Deployable Composite Tubular Roll-Out Boom, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — Deployable Space Systems (DSS) has developed an affordable and ultra-lightweight elastically self-deployable Roll-Out Boom technology that provides affordability and...

Deployment Strategies and Clustering Protocols Efficiency

Directory of Open Access Journals (Sweden)

Chérif Diallo

2017-06-01

Full Text Available Wireless sensor networks face significant design challenges due to limited computing and storage capacities and, most importantly, dependence on limited battery power. Energy is a critical resource and is often an important issue to the deployment of sensor applications that claim to be omnipresent in the world of future. Thus optimizing the deployment of sensors becomes a major constraint in the design and implementation of a WSN in order to ensure better network operations. In wireless networking, clustering techniques add scalability, reduce the computation complexity of routing protocols, allow data aggregation and then enhance the network performance. The well-known MaxMin clustering algorithm was previously generalized, corrected and validated. Then, in a previous work we have improved MaxMin by proposing a Single- node Cluster Reduction (SNCR mechanism which eliminates single-node clusters and then improve energy efficiency. In this paper, we show that MaxMin, because of its original pathological case, does not support the grid deployment topology, which is frequently used in WSN architectures. The unreliability feature of the wireless links could have negative impacts on Link Quality Indicator (LQI based clustering protocols. So, in the second part of this paper we show how our distributed Link Quality based d- Clustering Protocol (LQI-DCP has good performance in both stable and high unreliable link environments. Finally, performance evaluation results also show that LQI-DCP fully supports the grid deployment topology and is more energy efficient than MaxMin.

Latest developments, by Taylor Hitec Ltd, in power manipulators and deployed robots for the nuclear industry and elsewhere

International Nuclear Information System (INIS)

Lowe, D.B.

1985-01-01

Taylor Hitec recently achieved a major advancement in remote manipulator engineering with the successful commissioning of the 'Advanced Manipulator' - a high precision tool for remote working, commanded by powerful computerised control developed in partnership with CEGB Marchwood. In the progression of the technology involved a second manipulator has been designed, with significant changes in mechanisms and is now in manufacture. A radically different implement has been conceived and pursued through to the prototype stage in the form of a 'vertebrate' limb for deploying remote inspection apparatus. The designs and capabilities of these three devices are presented here in essence and consideration is given to wider applications. (author)

ACCELERATED SITE TECHNOLOGY DEPLOYMENT COST AND PERFORMANCE REPORT COMPARABILITY OF ISOCS INSTRUMENT IN RADIONUCLIDE CHARACTERICATION AT BROOKHAVEN NATIONAL LABORATORY

Energy Technology Data Exchange (ETDEWEB)

KALB,P.; LUCKETT,L.; MILLER,K.; GOGOLAK,C.; MILIAN,L.

2001-03-01

This report describes a DOE Accelerated Site Technology Deployment project being conducted at Brookhaven National Laboratory to deploy innovative, radiological, in situ analytical techniques. The technologies are being deployed in support of efforts to characterize the Brookhaven Graphite Research Reactor (BGRR) facility, which is currently undergoing decontamination and decommissioning. This report focuses on the deployment of the Canberra Industries In Situ Object Counting System (ISOCS) and assesses its data comparability to baseline methods of sampling and laboratory analysis. The battery-operated, field deployable gamma spectrometer provides traditional spectra of counts as a function of gamma energy. The spectra are then converted to radionuclide concentration by applying innovative efficiency calculations using monte carlo statistical methods and pre-defined geometry templates in the analysis software. Measurement of gamma emitting radionuclides has been accomplished during characterization of several BGRR components including the Pile Fan Sump, Above Ground Ducts, contaminated cooling fans, and graphite pile internals. Cs-137 is the predominant gamma-emitting radionuclide identified, with smaller quantities of Co-60 and Am-241 detected. The Project used the Multi-Agency Radiation Survey and Site Investigation Manual guidance and the Data Quality Objectives process to provide direction for survey planning and data quality assessment. Analytical results have been used to calculate data quality indicators (DQI) for the ISOCS measurements. Among the DQIs assessed in the report are sensitivity, accuracy, precision, bias, and minimum detectable concentration. The assessment of the in situ data quality using the DQIs demonstrates that the ISOCS data quality can be comparable to definitive level laboratory analysis when the field instrument is supported by an appropriate Quality Assurance Project Plan. A discussion of the results obtained by ISOCS analysis of

ACCELERATED SITE TECHNOLOGY DEPLOYMENT COST AND PERFORMANCE REPORT COMPARABILITY OF ISOCS INSTRUMENT IN RADIONUCLIDE CHARACTERICATION AT BROOKHAVEN NATIONAL LABORATORY

International Nuclear Information System (INIS)

KALB, P.; LUCKETT, L.; MILLER, K.; GOGOLAK, C.; MILIAN, L.

2001-01-01

This report describes a DOE Accelerated Site Technology Deployment project being conducted at Brookhaven National Laboratory to deploy innovative, radiological, in situ analytical techniques. The technologies are being deployed in support of efforts to characterize the Brookhaven Graphite Research Reactor (BGRR) facility, which is currently undergoing decontamination and decommissioning. This report focuses on the deployment of the Canberra Industries In Situ Object Counting System (ISOCS) and assesses its data comparability to baseline methods of sampling and laboratory analysis. The battery-operated, field deployable gamma spectrometer provides traditional spectra of counts as a function of gamma energy. The spectra are then converted to radionuclide concentration by applying innovative efficiency calculations using monte carlo statistical methods and pre-defined geometry templates in the analysis software. Measurement of gamma emitting radionuclides has been accomplished during characterization of several BGRR components including the Pile Fan Sump, Above Ground Ducts, contaminated cooling fans, and graphite pile internals. Cs-137 is the predominant gamma-emitting radionuclide identified, with smaller quantities of Co-60 and Am-241 detected. The Project used the Multi-Agency Radiation Survey and Site Investigation Manual guidance and the Data Quality Objectives process to provide direction for survey planning and data quality assessment. Analytical results have been used to calculate data quality indicators (DQI) for the ISOCS measurements. Among the DQIs assessed in the report are sensitivity, accuracy, precision, bias, and minimum detectable concentration. The assessment of the in situ data quality using the DQIs demonstrates that the ISOCS data quality can be comparable to definitive level laboratory analysis when the field instrument is supported by an appropriate Quality Assurance Project Plan. A discussion of the results obtained by ISOCS analysis of

Why precision?

Energy Technology Data Exchange (ETDEWEB)

Bluemlein, Johannes

2012-05-15

Precision measurements together with exact theoretical calculations have led to steady progress in fundamental physics. A brief survey is given on recent developments and current achievements in the field of perturbative precision calculations in the Standard Model of the Elementary Particles and their application in current high energy collider data analyses.

Why precision?

International Nuclear Information System (INIS)

Bluemlein, Johannes

2012-05-01

Precision measurements together with exact theoretical calculations have led to steady progress in fundamental physics. A brief survey is given on recent developments and current achievements in the field of perturbative precision calculations in the Standard Model of the Elementary Particles and their application in current high energy collider data analyses.

RELATIONS BETWEEN BASIC MOTOR ABILITIES AND SPECIFIC PRECISENESS OF FOOTBALLERS AGED 10-12

Directory of Open Access Journals (Sweden)

Miroslav Smajić

2007-05-01

Full Text Available According to the research on the sample of 256 footballers aged 10-12 and the battery including 20 tests for evaluation of the basic motor abilities and the battery of 24 tests for evaluation of specifi c preciseness, and as per canonic-correlation analysis, a general conclusion can be reached that the boys were rather different in their basic motor abilities. The differences were especially high in explosive strength, coordination, aerobic endurance and balance. One could also conclude that the sample treated in this manner (10-12 years of age is very heterogeneous with respect to basic motor abilities. The subjects showed the highest homogeneity in the tests of specifi c preciseness. They also achieved particularly good results in the tests of vertical target hitting by leg and head. Considering the relations of the basic motor abilities and specifi c preciseness, it was concluded that the structure-based basic motor-canonic factor might be interpreted as FACTOR OF SPEED ENDURANCE AND EXPLOSIVE STRENGTH, whereas structurebased canonic factor of specifi c preciseness might be interpreted as the FACTOR OF SPECIFIC PRECISENESS OF VERTICAL TARGET HITTING BY LEG AND HEAD. The structure of the relations of the fi rst pair of canonic factors indicates that footballers with lower speed endurance and lower explosive strength achieved poorer results in the tests of specifi c preciseness of vertical target hitting by leg and head, and vice versa. Structure of the relations of the second canonic factor indicates quite clearly that the footballers with lower repetitive strength achieved lower results in the tests of specifi c preciseness of horizontal and vertical target by leg and head in a newly created situation. Here of course, the opposite was true, i.e. footballers with higher repetitive strength were better in these tests too.

Service Creation and Deployment in Converged Networks

DEFF Research Database (Denmark)

Soler, José

for these experiences is the transition of telecommunication (telephony) networks from circuit switched based systems towards packet based ones. The text of this monograph proceeds, unaltered for the most, from the author’s PhD thesis “Framework for Deployment of Advanced Telecommunication Services in Current......This monograph (Early Experiences related to Service Creation & Deployment in Converged Networks) presents different experiences related to architectures and mechanisms for deployment of telephony services, understood as especial features complementing the basic voice service. The context...... and Future Converged Networks”, carried out at the Technical University of Denmark in the period [April 2002-April 2005]. Even though the technologies presented in the text have evolved from that period until now, the presented scenarios and setups are still valid as interesting initial steps in the realm....

GABA-Mediated Presynaptic Inhibition Is Required for Precision of Long-Term Memory

Science.gov (United States)

Cullen, Patrick K.; Dulka, Brooke N.; Ortiz, Samantha; Riccio, David C.; Jasnow, Aaron M.

2014-01-01

Though much attention has been given to the neural structures that underlie the long-term consolidation of contextual memories, little is known about the mechanisms responsible for the maintenance of memory precision. Here, we demonstrate a rapid time-dependent decline in memory precision in GABA [subscript B(1a)] receptor knockout mice. First, we…

Precision mechatronics based on high-precision measuring and positioning systems and machines

Science.gov (United States)

Jäger, Gerd; Manske, Eberhard; Hausotte, Tino; Mastylo, Rostyslav; Dorozhovets, Natalja; Hofmann, Norbert

2007-06-01

Precision mechatronics is defined in the paper as the science and engineering of a new generation of high precision systems and machines. Nanomeasuring and nanopositioning engineering represents important fields of precision mechatronics. The nanometrology is described as the today's limit of the precision engineering. The problem, how to design nanopositioning machines with uncertainties as small as possible will be discussed. The integration of several optical and tactile nanoprobes makes the 3D-nanopositioning machine suitable for various tasks, such as long range scanning probe microscopy, mask and wafer inspection, nanotribology, nanoindentation, free form surface measurement as well as measurement of microoptics, precision molds, microgears, ring gauges and small holes.

Large Deployable Reflector Technologies for Future European Telecom and Earth Observation Missions

Science.gov (United States)

Ihle, A.; Breunig, E.; Dadashvili, L.; Migliorelli, M.; Scialino, L.; van't Klosters, K.; Santiago-Prowald, J.

2012-07-01

This paper presents requirements, analysis and design results for European large deployable reflectors (LDR) for space applications. For telecommunications, the foreseeable use of large reflectors is associated to the continuous demand for improved performance of mobile services. On the other hand, several earth observation (EO) missions can be identified carrying either active or passive remote sensing instruments (or both), in which a large effective aperture is needed e.g. BIOMASS. From the European point of view there is a total dependence of USA industry as such LDRs are not available from European suppliers. The RESTEO study is part of a number of ESA led activities to facilitate European LDR development. This paper is focused on the structural-mechanical aspects of this study. We identify the general requirements for LDRs with special emphasis on launcher accommodation for EO mission. In the next step, optimal concepts for the LDR structure and the RF-Surface are reviewed. Regarding the RF surface, both, a knitted metal mesh and a shell membrane based on carbon fibre reinforced silicon (CFRS) are considered. In terms of the backing structure, the peripheral ring concept is identified as most promising and a large number of options for the deployment kinematics are discussed. Of those, pantographic kinematics and a conical peripheral ring are selected. A preliminary design for these two most promising LDR concepts is performed which includes static, modal and kinematic simulation and also techniques to generate the reflector nets.

EarthScope's Transportable Array: Status of the Alaska Deployment and Guide to Resources for Lower48 Deployment

Science.gov (United States)

Busby, R. W.; Woodward, R.; Aderhold, K.; Frassetto, A.

2017-12-01

The Alaska Transportable Array deployment is completely installed, totaling 280 stations, with 194 new stations and 86 existing stations, 28 of those upgraded with new sensor emplacement. We briefly summarize the deployment of this seismic network, describe the added meteorological instruments and soil temperature gauges, and review our expectations for operation and demobilization. Curation of data from the contiguous Lower-48 States deployment of Transportable Array (>1800 stations, 2004-2015) has continued with the few gaps in real-time data replaced by locally archived files as well as minor adjustments in metadata. We highlight station digests that provide more detail on the components and settings of individual stations, documentation of standard procedures used throughout the deployment and other resources available online. In cooperation with IRIS DMC, a copy of the complete TA archive for the Lower-48 period has been transferred to a local disk to experiment with data access and software workflows that utilize most or all of the seismic timeseries, in contrast to event segments. Assembling such large datasets reliably - from field stations to a well managed data archive to a user's workspace - is complex. Sharing a curated and defined data volume with researchers is a potentially straightforward way to make data intensive analyses less difficult. We note that data collection within the Lower-48 continues with 160 stations of the N4 network operating at increased sample rates (100 sps) as part of the CEUSN, as operational support transitions from NSF to USGS.

Industrializing Offshore Wind Power with Serial Assembly and Lower-cost Deployment - Final Report

Energy Technology Data Exchange (ETDEWEB)

Kempton, Willett [Univ. of Delaware, Newark, DE (United States)

2017-12-11

A team of engineers and contractors has developed a method to move offshore wind installation toward lower cost, faster deployment, and lower environmental impact. A combination of methods, some incremental and some breaks from past practice, interact to yield multiple improvements. Three designs were evaluated based on detailed engineering: 1) a 5 MW turbine on a jacket with pin piles (base case), 2) a 10 MW turbine on a conventional jacket with pin piles, assembled at sea, and 3) a 10 MW turbine on tripod jacket with suction buckets (caissons) and with complete turbine assembly on-shore. The larger turbine, assembly ashore, and the use of suction buckets together substantially reduce capital cost of offshore wind projects. Notable capital cost reductions are: changing from 5 MW to 10 MW turbine, a 31% capital cost reduction, and assembly on land then single-piece install at sea an additional 9% capital cost reduction. An estimated Design 4) estimates further cost reduction when equipment and processes of Design 3) are optimized, rather than adapted to existing equipment and process. Cost of energy for each of the four Designs are also calculated, yielding approximately the same percentage reductions. The methods of Design 3) analyzed here include accepted structures such as suction buckets used in new ways, innovations conceived but previously without engineering and economic validation, combined with new methods not previously proposed. Analysis of Designs 2) and 3) are based on extensive engineering calculations and detailed cost estimates. All design methods can be done with existing equipment, including lift equipment, ports and ships (except that design 4 assumes a more optimized ship). The design team consists of experienced offshore structure designers, heavy lift engineers, wind turbine designers, vessel operators, and marine construction contractors. Comparing the methods based on criteria of cost and deployment speed, the study selected the third design

Supporting Collaborative Model and Data Service Development and Deployment with DevOps

Science.gov (United States)

David, O.

2016-12-01

Adopting DevOps practices for model service development and deployment enables a community to engage in service-oriented modeling and data management. The Cloud Services Integration Platform (CSIP) developed the last 5 years at Colorado State University provides for collaborative integration of environmental models into scalable model and data services as a micro-services platform with API and deployment infrastructure. Originally developed to support USDA natural resource applications, it proved suitable for a wider range of applications in the environmental modeling domain. While extending its scope and visibility it became apparent community integration and adequate work flow support through the full model development and application cycle drove successful outcomes.DevOps provide best practices, tools, and organizational structures to optimize the transition from model service development to deployment by minimizing the (i) operational burden and (ii) turnaround time for modelers. We have developed and implemented a methodology to fully automate a suite of applications for application lifecycle management, version control, continuous integration, container management, and container scaling to enable model and data service developers in various institutions to collaboratively build, run, deploy, test, and scale services within minutes.To date more than 160 model and data services are available for applications in hydrology (PRMS, Hydrotools, CFA, ESP), water and wind erosion prediction (WEPP, WEPS, RUSLE2), soil quality trends (SCI, STIR), water quality analysis (SWAT-CP, WQM, CFA, AgES-W), stream degradation assessment (SWAT-DEG), hydraulics (cross-section), and grazing management (GRAS). In addition, supporting data services include soil (SSURGO), ecological site (ESIS), climate (CLIGEN, WINDGEN), land management and crop rotations (LMOD), and pesticides (WQM), developed using this workflow automation and decentralized governance.

The role of postdeployment social factors in linking deployment experiences and current posttraumatic stress disorder symptomatology among male and female veterans.

Science.gov (United States)

Smith, Brian N; Wang, Joyce M; Vaughn-Coaxum, Rachel A; Di Leone, Brooke A L; Vogt, Dawne

2017-01-01

The postdeployment social context is likely highly salient in explaining mental health symptoms following deployment. The aim of this study was to examine the role of postdeployment social factors (social support and social reintegration difficulty) in linking deployment-related experiences (warfare exposure, sexual harassment, concerns about relationship disruptions, and deployment social support) and posttraumatic stress disorder (PTSD) symptomatology in male and female veterans. A survey was administered to 998 potential participants (after accounting for undeliverable mail) who had returned from deployment to Afghanistan or Iraq. Completed surveys were received from 469 veterans, yielding a response rate of 47%. Hypotheses were examined using structural equation modeling. For male and female veterans, deployment factors predicted later PTSD symptoms through postdeployment social support and social reintegration, with lower support and higher social reintegration difficulty both associated with higher PTSD symptomatology. While the final models for women and men indicated similar risk mechanisms, some differences in pathways were observed. Sexual harassment presented more of a risk for women, whereas lower social support was a greater risk factor for men. Postdeployment social factors appear to represent potentially important targets for interventions aiming to reduce the potential impact of stressful deployment experiences.

Cognitive ability and risk of post-traumatic stress disorder after military deployment

DEFF Research Database (Denmark)

Nissen, Lars R.; Karstoft, Karen-Inge; Vedtofte, Mia S.

2017-01-01

Background: Studies of the association between pre-deployment cognitive ability and post-deployment post-traumatic stress disorder (PTSD) have shown mixed results. Aims: To study the influence of pre-deployment cognitive ability on PTSD symptoms 6-8 months post-deployment in a large population...

Paving the Way for Small Satellite Access to Orbit: Cyclops' Deployment of SpinSat, the Largest Satellite Ever Deployed from the International Space Station

Science.gov (United States)

Hershey, Matthew P.; Newswander, Daniel R.; Smith, James P.; Lamb, Craig R.; Ballard, Perry G.

2015-01-01

The Space Station Integrated Kinetic Launcher for Orbital Payload Systems (SSIKLOPS), known as "Cyclops" to the International Space Station (ISS) community, successfully deployed the largest satellite ever (SpinSat) from the ISS on November 28, 2014. Cyclops, a collaboration between the NASA ISS Program, NASA Johnson Space Center Engineering, and Department of Defense Space Test Program (DoD STP) communities, is a dedicated 10-100 kg class ISS small satellite deployment system. This paper will showcase the successful deployment of SpinSat from the ISS. It will also outline the concept of operations, interfaces, requirements, and processes for satellites to utilize the Cyclops satellite deployment system.

Time Deployment Study for Annulus Pumping

International Nuclear Information System (INIS)

REBERGER, D.W.

2000-01-01

Radioactive wastes from processing irradiated uranium fuels have been stored as alkaline slurries in underground tanks at the Hanford Site. Single-shell tanks (SST) and double-shell tanks (DST) of various sizes were used for waste storage. Of the total 177 tanks, there are 28 DSTs. DSTs are located in AN, AP, AW, AY, AZ, and SY tank farms in the 200 East (200E) and 200-West (200W) Areas. The storage capacities of the DSTs vary from 980,000 to 1,140,000 gal. DSTs are designed and constructed as an integral steel structure, i.e., an inner shell within an outer shell, so that any leak from the inner shell is confined within the annulus without impacting the environment. The inner shell provides primary containment for the wastes and the outer shell provides secondary containment in the form of an annulus. The annulus of a DST is equipped with a pump pit, leak detection probes, and other accessories. The existing annulus pumps in the DSTs need to be revamped with a new system to reduce operating costs and reduce the time to deploy a pumping system. The new pumping system will minimize the likelihood of a release of waste into the environment; improve capability of waste removal to the maximum extent possible to comply with Washington Administrative Code (WAC) 173-303-640 and Code of Federal Regulations (CFR) 40 CFR 265.193. This study addresses the time required to deploy an annulus pumping system designed to fit any DST after detection of a leak in the inner shell of the DST

Precise determination of the spin structure function g{sub 1} of the proton, deuteron and neutron

Energy Technology Data Exchange (ETDEWEB)

Airapetian, A. [Michigan Univ., Ann Arbor, MI (United States). Randall Lab. of Physics; Akopov, N.; Akopov, Z. [Yerevan Physics Insitute, Yerevan (AM)] (and others)

2006-09-15

Precise measurements of the spin structure functions of the proton g{sup p}{sub 1}(x,Q{sup 2}) and deuteron g{sup d}{sub 1}(x,Q{sup 2}) are presented over the kinematic range 0.0041 {<=} x {<=} 0.9 and 0.18 GeV{sup 2} {<=} Q{sup 2} {<=} 20 GeV{sup 2}. The data were collected at the HERMES experiment at DESY, in deep-inelastic scattering of 27.6 GeV longitudinally polarized positrons off longitudinally polarized hydrogen and deuterium gas targets internal to the HERA storage ring. The neutron spin structure function g{sup n}{sub 1} is extracted by combining proton and deuteron data. The integrals of g{sup p,d}{sub 1} at Q{sup 2}=5 GeV{sup 2} are evaluated over the measured x range. Neglecting any possible contribution to the g{sup d}{sub 1} integral from the region x {<=} 0.021, a value of 0.330{+-}0.011(theo.){+-}0.025(exp.){+-}0.028(evol.) is obtained for the flavor-singlet axial charge a{sub 0} in a leading-twist NNLO analysis. (orig.)

Deployment Effects of Marine Renewable Energy Technologies: Wave Energy Scenarios

Energy Technology Data Exchange (ETDEWEB)

Mirko Previsic

2010-06-17

other project teams funded by DoE which are focused on regulatory issues (Pacific Energy Ventures) and navigational issues (PCCI). The results of this study are structured into three reports: (1) Wave power scenario description (2) Tidal power scenario description (3) Framework for Identifying Key Environmental Concerns This is the first report in the sequence and describes the results of conceptual feasibility studies of wave power plants deployed in Humboldt County, California and Oahu, Hawaii. These two sites contain many of the same competing stakeholder interactions identified at other wave power sites in the U.S. and serve as representative case studies. Wave power remains at an early stage of development. As such, a wide range of different technologies are being pursued by different manufacturers. In order to properly characterize potential effects, it is useful to characterize the range of technologies that could be deployed at the site of interest. An industry survey informed the process of selecting representative wave power devices. The selection criteria requires that devices are at an advanced stage of development to reduce technical uncertainties, and that enough data are available from the manufacturers to inform the conceptual design process of this study. Further, an attempt is made to cover the range of different technologies under development to capture variations in potential environmental effects. Table 1 summarizes the selected wave power technologies. A number of other developers are also at an advanced stage of development, but are not directly mentioned here. Many environmental effects will largely scale with the size of the wave power plant. In many cases, the effects of a single device may not be measurable, while larger scale device arrays may have cumulative impacts that differ significantly from smaller scale deployments. In order to characterize these effects, scenarios are established at three deployment scales which nominally represent

Precision studies of proton structure and jet energy scale with the CMS detector at the LHC

Energy Technology Data Exchange (ETDEWEB)

Haitz, Dominik

2016-05-20

+jet events can be utilized for studies of the proton structure. In the parton model, this structure is expressed by the parton distribution functions (PDFs) which predict the probability to nd a certain proton constituent (a parton) with a proton momentum fraction x at an energy scale Q. The PDFs are not predicted by perturbative QCD but have to be experimentally determined. In this thesis, a method to constrain the parameters of the PDFs by measuring the distributions of kinematic quantities of Z bosons is explored. This method exploits the correlation between the PDFs and the expected number of events with Z bosons in particular phase space regions. By fitting the PDFs to these data, the PDF parameters can be determined. If the measurement is precise enough, the uncertainties in the PDFs can be reduced. Z+jet events can also be used for jet energy calibration: All physics analyses at the LHC rely on the precise reconstruction of the objects produced in a collision. Among the most important of these objects are jets, collimated streams of particles produced by the hadronization of partons. As there are numerous effects that bias the jet measurement, the precise determination of jet energies is among the most challenging experimental tasks. Sophisticated techniques have been developed to deal with the various systematic biases. One of the most important steps is the data-driven calibration with balancing methods: Exploiting momentum conservation, the jet transverse momentum is compared with the transverse momentum of a well-measured reference object and consequently corrected. In this thesis, the jet energy scale is calibrated by studying Z(→μ{sup +}μ{sup -})+jet events.

Vibration control for precision manufacturing using piezoelectric actuators

Energy Technology Data Exchange (ETDEWEB)

Martinez, D.R.; Hinnerichs, T.D.; Redmond, J.M.

1995-12-31

Piezoelectric actuators provide high frequency, force, and stiffness capabilities along with reasonable Stroke limits, all of which can be used to increase performance levels in precision manufacturing systems. This paper describes two examples of embedding piezoelectric actuators in structural components for vibration control. One example involves suppressing the self excited chatter phenomenon in the metal cutting process of a milling machine and the other involves damping vibrations induced by rigid body stepping of a photolithography platen. Finite element modeling and analyses are essential for locating and sizing the actuators and permit further simulation studies of the response of the dynamic system. Experimental results are given for embedding piezoelectric actuators in a cantilevered bar configuration, which was used as a surrogate machine tool structure. These results are incorporated into a previously developed milling process simulation and the effect of the control on the cutting process stability diagram is quantified. Experimental results are also given for embedding three piezoelectric actuators in a surrogate photolithography platen to suppress vibrations. These results demonstrate the potential benefit that can be realized by applying advances from the field of adaptive structures to problems in precision manufacturing.

Modelling of Structural Loads in Drag Augmented Space Debris Removal Concepts

DEFF Research Database (Denmark)

Kristensen, Anders Schmidt; Nikolajsen, Jan Ánike; Lauridsen, Peter Riddersholm

2017-01-01

A Self-deployable Deorbiting Space Structure (SDSS) is used for drag augmented space debris removal. A highly flexible frame allows for a folding of the structure by bifurcation. This research models the structural loads during the deployment and unfolding of the drag sail in Low Earth Orbit (LEO......). The Spacecraft travels with 7.8 km/s at deployment. As the drag sail unfolds instantaneously the structure must withstand the loads from the unfolding and the drag. Thermal loads are included in the FEA as the temperature varies from -80°C to +80°C during deorbit. The results are used to verify the structural...

15 CFR 270.102 - Conditions for establishment and deployment of a Team.

Science.gov (United States)

2010-01-01

... deployment of a Team. 270.102 Section 270.102 Commerce and Foreign Trade Regulations Relating to Commerce and... SAFETY TEAMS NATIONAL CONSTRUCTION SAFETY TEAMS Establishment and Deployment of Teams § 270.102 Conditions for establishment and deployment of a Team. (a) The Director may establish a Team for deployment...

ALMR deployment economic analysis

International Nuclear Information System (INIS)

Delene, J.G.; Fuller, L.C.; Hudson, C.R.

1993-06-01

This analysis seeks to model and evaluate the economics of the use of Advanced Liquid Metal Reactors (ALMR) as a component of this country's future electricity generation mix. The ALMR concept has the ability to utilize as fuel the fissile material contained in previously irradiated nuclear fuel (i.e., spent fuel). While not a requirement for the successful deployment of ALMR power plant technology, the reprocessing of spent fuel from light water reactors (LWR) is necessary for any rapid introduction of ALMR power plants. In addition, the reprocessing of LWR spent fuel may reduce the number of high level waste repositories needed in the future by burning the long-lived actinides produced in the fission process. With this study, the relative economics of a number of potential scenarios related to these issues are evaluated. While not encompassing the full range of all possibilities, the cases reported here provide an indication of the potential costs, timings, and relative economic attractiveness of ALMR deployment

Method of high precision interval measurement in pulse laser ranging system

Science.gov (United States)

Wang, Zhen; Lv, Xin-yuan; Mao, Jin-jin; Liu, Wei; Yang, Dong

2013-09-01

Laser ranging is suitable for laser system, for it has the advantage of high measuring precision, fast measuring speed,no cooperative targets and strong resistance to electromagnetic interference,the measuremen of laser ranging is the key paremeters affecting the performance of the whole system.The precision of the pulsed laser ranging system was decided by the precision of the time interval measurement, the principle structure of laser ranging system was introduced, and a method of high precision time interval measurement in pulse laser ranging system was established in this paper.Based on the analysis of the factors which affected the precision of range measure,the pulse rising edges discriminator was adopted to produce timing mark for the start-stop time discrimination,and the TDC-GP2 high precision interval measurement system based on TMS320F2812 DSP was designed to improve the measurement precision.Experimental results indicate that the time interval measurement method in this paper can obtain higher range accuracy. Compared with the traditional time interval measurement system,the method simplifies the system design and reduce the influence of bad weather conditions,furthermore,it satisfies the requirements of low costs and miniaturization.

Mobile Robotic Teams Applied to Precision Agriculture

Energy Technology Data Exchange (ETDEWEB)

Anderson, Matthew Oley; Kinoshita, Robert Arthur; Mckay, Mark D; Willis, Walter David; Gunderson, R.W.; Flann, N.S.

1999-04-01

The Idaho National Engineering and Environmental Laboratory (INEEL) and Utah State University’s Center for Self-Organizing and Intelligent Systems (CSOIS) have developed a team of autonomous robotic vehicles applicable to precision agriculture. A unique technique has been developed to plan, coordinate, and optimize missions in large structured environments for these autonomous vehicles in realtime. Two generic tasks are supported: 1) Driving to a precise location, and 2) Sweeping an area while activating on-board equipment. Sensor data and task achievement data is shared among the vehicles enabling them to cooperatively adapt to changing environmental, vehicle, and task conditions. This paper discusses the development of the autonomous robotic team, details of the mission-planning algorithm, and successful field demonstrations at the INEEL.

Mobile Robotic Teams Applied to Precision Agriculture

Energy Technology Data Exchange (ETDEWEB)

M.D. McKay; M.O. Anderson; N.S. Flann (Utah State University); R.A. Kinoshita; R.W. Gunderson; W.D. Willis (INEEL)

1999-04-01

The Idaho National Engineering and Environmental Laboratory (INEEL) and Utah State University�s Center for Self-Organizing and Intelligent Systems (CSOIS) have developed a team of autonomous robotic vehicles applicable to precision agriculture. A unique technique has been developed to plan, coordinate, and optimize missions in large structured environments for these autonomous vehicles in real-time. Two generic tasks are supported: 1) Driving to a precise location, and 2) Sweeping an area while activating on-board equipment. Sensor data and task achievement data is shared among the vehicles enabling them to cooperatively adapt to changing environmental, vehicle, and task conditions. This paper discusses the development of the autonomous robotic team, details of the mission-planning algorithm, and successful field demonstrations at the INEEL.

Templated Atom-Precise Galvanic Synthesis and Structure Elucidation of a [Ag 24 Au(SR) 18 ] − Nanocluster

KAUST Repository

Bootharaju, Megalamane Siddaramappa

2015-11-27

Synthesis of atom-precise alloy nanoclusters with uniform composition is challenging when the alloying atoms are similar in size (for example, Ag and Au). A galvanic exchange strategy has been devised to produce a compositionally uniform [Ag24Au(SR)18]- cluster (SR: thiolate) using a pure [Ag25(SR)18]- cluster as a template. Conversely, the direct synthesis of Ag24Au cluster leads to a mixture of [Ag25-xAux(SR)18]-, x=1-8. Mass spectrometry and crystallography of [Ag24Au(SR)18]- reveal the presence of the Au heteroatom at the Ag25 center, forming Ag24Au. The successful exchange of the central Ag of Ag25 with Au causes perturbations in the Ag25 crystal structure, which are reflected in the absorption, luminescence, and ambient stability of the particle. These properties are compared with those of Ag25 and Ag24Pd clusters with same ligand and structural framework, providing new insights into the modulation of cluster properties with dopants at the single-atom level.

High precision, low disturbance calibration of the High Voltage system of the CMS Barrel Electromagnetic Calorimeter

CERN Document Server

Marzocchi, Badder

2017-01-01

The CMS Electromagnetic Calorimeter is made of scintillating lead tungstate crystals, using avalanche photodiodes (APD) as photo-detectors in the barrel part. The high voltage system, consisting of 1224 channels, biases groups of 50 APD pairs, each at a voltage of about 380 V. The APD gain dependence on the voltage is 3pct/V. A stability of better than 60 mV is needed to have negligible impact on the calorimeter energy resolution. Until 2015 manual calibrations were performed yearly. A new calibration system was deployed recently, which satisfies the requirement of low disturbance and high precision. The system is discussed in detail and first operational experience is presented.

49 CFR 268.5 - Federal funding sources for the Maglev Deployment Program.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Federal funding sources for the Maglev Deployment... TECHNOLOGY DEPLOYMENT PROGRAM Overview § 268.5 Federal funding sources for the Maglev Deployment Program. (a) Federal Maglev Funds. Section 322 of Title 23 provides for the following funds for the Maglev Deployment...

Supporting Military Families with Young Children throughout the Deployment Lifecycle

Science.gov (United States)

2016-10-01

Group, Family Advocacy, Child and Family Behavioral Health, Soldier Readiness Program (SRP), Family Life Chaplain Training Center, Fort Hood Housing ...resilience and child well-being, Soldier and non-deploying parents must successfully meet the challenges of caregiving throughout the deployment cycle ...reintegration program to reduce parenting stress and promote family resilience in Active Duty military families through all phases of the deployment cycle

On the Integration of Automatic Deployment into the ABS Modeling Language

NARCIS (Netherlands)

C.P.T. de Gouw (Stijn); M. Lienhardt; J. Mauro (Jacopo); B. Nobakht (Behrooz); G. Zavattaro (Gianluigi); S. Dustdar; F. Leymann; M. Villari

2015-01-01

htmlabstractIn modern software systems, deployment is an integral and critical part of application development (see, e.g., the DevOps approach to software development). Nevertheless, deployment is usually overlooked at the modeling level, thus losing the possibility to perform deployment conscious

Evaluating the performance of a low-cost GPS in precision agriculture applications

DEFF Research Database (Denmark)

Jensen, Kjeld; Larsen, Morten; Simonsen, Tom

2012-01-01

Field Robots are often equipped with a Real Time Kinematic (RTK) GPS to obtain precise positioning. In many precision agriculture applications, however, the robot operates in semi-structured environments like orchards and row crops, where local sensors such as computer vision and laser range...... scanners can produce accurate positioning relative to the crops. GPS is then primarily needed for robust inter-row navigation. This work evaluates a new low-cost GPS. Static tests were used to test the absolute accuracy. To test the GPS in a precision agriculture environment it was installed on a robot...

LWR Spent Fuel Management for the Smooth Deployment of FBR

International Nuclear Information System (INIS)

Fukasawa, T.; Yamashita, J.; Hoshino, K.; Sasahira, A.; Inoue, T.; Minato, K.; Sato, S.

2015-01-01

Fast breeder reactors (FBR) and FBR fuel cycle are indispensable to prevent the global warming and to secure the long-term energy supply. Commercial FBR expects to be deployed from around 2050 until around 2110 in Japan by the replacement of light water reactors (LWR) after their 60 years life. The FBR deployment needs Pu (MOX) from the LWR-spent fuel (SF) reprocessing. As Japan can posses little excess Pu, its balance control is necessary between LWR-SF management (reprocessing) and FBR deployment. The fuel cycle systems were investigated for the smooth FBR deployment and the effectiveness of proposed flexible system was clarified in this work. (author)

Accelerating the deployment of offshore renewable energy technologies. Final Report

Energy Technology Data Exchange (ETDEWEB)

MacDonald, Mott

2011-02-15

Offshore wind energy and ocean energy (i.e. wave and tidal) are at different stages of technology development and deployment, and, as such, they require different approaches for successful deployment. However, regardless of their deployment stage, these technologies may face common hurdles in their way to market competitiveness. IEA-RETD has completed a study with the overall objective to assist policy makers and project developers in a better understanding of these barriers and the specifics of offshore renewable energy and to give them practical guidelines. These include an offshore energy deployment framework, substantiated by evidence-based analyses, and recommendations for future policies design, including best practices for allocation of seafloor rights.

IEA Wind Task 23 Offshore Wind Technology and Deployment. Subtask 1 Experience with Critical Deployment Issues. Final Technical Report

OpenAIRE

Lemming, Jørgen Kjærgaard

2010-01-01

The final report for IEA Wind Task 23, Offshore Wind Energy Technology and Deployment, is made up of two separate reports: Subtask 1: Experience with Critical Deployment Issues and Subtask 2: Offshore Code Comparison Collaborative (OC3). The Subtask 1 report included here provides background information and objectives of Task 23. It specifically discusses ecological issues and regulation, electrical system integration and offshore wind, external conditions, and key conclusions for Subtask 1. ...

Prospects for Precise Measurements with Echo Atom Interferometry

Directory of Open Access Journals (Sweden)

Brynle Barrett

2016-06-01

Full Text Available Echo atom interferometers have emerged as interesting alternatives to Raman interferometers for the realization of precise measurements of the gravitational acceleration g and the determination of the atomic fine structure through measurements of the atomic recoil frequency ω q . Here we review the development of different configurations of echo interferometers that are best suited to achieve these goals. We describe experiments that utilize near-resonant excitation of laser-cooled rubidium atoms by a sequence of standing wave pulses to measure ω q with a statistical uncertainty of 37 parts per billion (ppb on a time scale of ∼50 ms and g with a statistical precision of 75 ppb. Related coherent transient techniques that have achieved the most statistically precise measurements of atomic g-factor ratios are also outlined. We discuss the reduction of prominent systematic effects in these experiments using off-resonant excitation by low-cost, high-power lasers.

Atomically Precise Nanocluster Assemblies Encapsulating Plasmonic Gold Nanorods.

Science.gov (United States)

Chakraborty, Amrita; Fernandez, Ann Candice; Som, Anirban; Mondal, Biswajit; Natarajan, Ganapati; Paramasivam, Ganesan; Lahtinen, Tanja; Häkkinen, Hannu; Nonappa, Nonappa; Pradeep, Thalappil

2018-04-01

We present the self-assembled structures of atomically precise, ligand-protected noble metal nanoclusters leading to encapsulation of plasmonic gold nanorods (GNRs). Unlike highly sophisticated DNA nanotechnology, our approach demonstrates a strategically simple hydrogen bonding-directed self-assembly of nanoclusters leading to octahedral nanocrystals encapsulating GNRs. Specifically, we use the p-mercaptobenzoic acid (pMBA) protected atomically precise nanocluster, Na4[Ag44(pMBA)30] and pMBA functionalized GNRs. High resolution transmission and scanning transmission electron tomographic reconstructions suggest that the geometry of the GNR surface is responsible for directing the assembly of silver nanoclusters via H-bonding leading to octahedral symmetry. Further, use of water dispersible gold nanoclusters, Au~250(pMBA)n and Au102(pMBA)44 also formed layered shells encapsulating GNRs. Such cluster assemblies on colloidal particles present a new category of precision hybrids with diverse possibilities. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Modeling of a New Structure of Precision Air Conditioning System Using Secondary Condenser for Rh Regulation

Directory of Open Access Journals (Sweden)

Aries Subiantoro

2012-05-01

Full Text Available A dynamic mathematical model for a new structure of precision air conditioning (PAC has been developed. The proposed PAC uses an additional secondary condenser for relative humidity regulation compared to a basic refrigeration system. The work mechanism for this system and a vapour-compression cycle process of the system are illustrated using psychrometric chart and pressure-enthalpy diagram. A non-linear system model is derived based on the conservation of mass and energy balance principles and then linearized at steady state operating point for developing a 8th-order state space model suited for multivariable controller design. The quality of linearized model is analyzed in terms of transient response, controllability, observability, and interaction between input-output variables. The developed model is verified through simulation showing its ability for imitating the nonlinear behavior and the interaction of input-output variables.

In-Flight Suppressant Deployment Temperatures

National Research Council Canada - National Science Library

Bein, Donald

2006-01-01

.... An assessment is made of the model output versus some aircraft measurement data, fire suppressant boiling point criterion, as well as the history of altitude/temperature at which fire suppressants have been deployed...

A Comparison of Dependent Primary Care Utilization Rates Based on Deployments

Science.gov (United States)

2009-03-09

analysis to obtain the deployment data was completed by ASMR , another contractor used to Health Care Utilization and Deployments 15 complete...2007. The deployment dataset was created by ASMR using all encounter data for active duty Soldiers and running the Social Security numbers of these

White Paper on Dish Stirling Technology: Path Toward Commercial Deployment

Energy Technology Data Exchange (ETDEWEB)

Andraka, Charles E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Concentrating Solar Power Dept.; Stechel, Ellen [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Concentrating Solar Power Dept.; Becker, Peter [Stirling Energy Systems, Scottsdale, AZ (United States); Messick, Brian [Stirling Energy Systems, Scottsdale, AZ (United States)

2016-07-01

Dish Stirling energy systems have been developed for distributed and large-scale utility deployment. This report summarizes the state of the technology in a joint project between Stirling Energy Systems, Sandia National Laboratories, and the Department of Energy in 2011. It then lays out a feasible path to large scale deployment, including development needs and anticipated cost reduction paths that will make a viable deployment product.

Standardization of transportation classes for object-oriented deployment simulations.

Energy Technology Data Exchange (ETDEWEB)

Burke, J. F., Jr.; Howard, D. L.; Jackson, J.; Macal, C. M.; Nevins, M. R.; Van Groningen, C. N.

1999-07-30

Many recent efforts to integrate transportation and deployment simulations, although beneficial, have lacked a feature vital for seamless integration: a common data class representation. It is an objective of the Department of Defense (DoD) to standardize all classes used in object-oriented deployment simulations by developing a standard class attribute representation and behavior for all deployment simulations that rely on an underlying class representation. The Extensive Hierarchy and Object Representation for Transportation Simulations (EXHORT) is a collection of three hierarchies that together will constitute a standard and consistent class attribute representation and behavior that could be used directly by a large set of deployment simulations. The first hierarchy is the Transportation Class Hierarchy (TCH), which describes a significant portion of the defense transportation system; the other two deal with infrastructure and resource classes. EXHORT will allow deployment simulations to use the same set of underlying class data, ensure transparent exchanges, reduce the effort needed to integrate simulations, and permit a detailed analysis of the defense transportation system. This paper describes EXHORT's first hierarchy, the TCH, and provides a rationale for why it is a helpful tool for modeling major portions of the defense transportation system.

Sharpening Precision Medicine by a Thorough Interrogation of Metabolic Individuality

Directory of Open Access Journals (Sweden)

Kirk Beebe

2016-01-01

Full Text Available Precision medicine is an active component of medical practice today, but aspirations are to both broaden its reach to a greater diversity of individuals and improve its “precision” by enhancing the ability to define even more disease states in combination with associated treatments. Given complexity of human phenotypes, much work is required. In this review, we deconstruct this challenge at a high level to define what is needed to move closer toward these aspirations. In the context of the variables that influence the diverse array of phenotypes across human health and disease – genetics, epigenetics, environmental influences, and the microbiome – we detail the factors behind why an individual's biochemical (metabolite composition is increasingly regarded as a key element to precisely defining phenotypes. Although an individual's biochemical (metabolite composition is generally regarded, and frequently shown, to be a surrogate to the phenotypic state, we review how metabolites (and therefore an individual's metabolic profile are also functionally related to the myriad of phenotypic influencers like genetics and the microbiota. We describe how using the technology to comprehensively measure an individual's biochemical profile – metabolomics – is integrative to defining individual phenotypes and how it is currently being deployed in efforts to continue to elaborate on human health and disease in large population studies. Finally, we summarize instances where metabolomics is being used to assess individual health in instances where signatures (i.e. biomarkers have been defined.

Solar array deployment analysis considering path-dependent behavior of a tape spring hinge

Energy Technology Data Exchange (ETDEWEB)

Kim, Kyung Won; Park, Young Jin [KAIST, Daejeon (Korea, Republic of)

2015-05-15

Solar array deployment analysis is conducted considering the path-dependent nonlinear behavior of tape spring hinge. Such hinges offer many advantages over rigid hinges; they are self-deployable, self-locking, lightweight, and simple. However, they show strongly nonlinear behavior with respect to rotation angle, making deployment analysis difficult. To accurately consider the characteristics of tape spring hinges for deployment analysis, a path-dependent path identification (PI) method for tracing the previous path of the moment is introduced. To analyze the deployment motion, the governing equation for solar array deployment is derived within the framework of Kane's dynamic equation for three deployable solar panels. The numerical solution is compared with the Recurdyn's multi-body dynamics analysis solution using experimentally measured moment-rotation profiles. Solar array deployment analysis is conducted by considering and not considering the path-dependent PI method. This simulation example shows that the proposed path-dependent PI method is very effective for accurately predicting the deployment motion.

Practical precision measurement

International Nuclear Information System (INIS)

Kwak, Ho Chan; Lee, Hui Jun

1999-01-01

This book introduces basic knowledge of precision measurement, measurement of length, precision measurement of minor diameter, measurement of angles, measurement of surface roughness, three dimensional measurement, measurement of locations and shapes, measurement of screw, gear testing, cutting tools testing, rolling bearing testing, and measurement of digitalisation. It covers height gauge, how to test surface roughness, measurement of plan and straightness, external and internal thread testing, gear tooth measurement, milling cutter, tab, rotation precision measurement, and optical transducer.

FY2000 Hanford Technology Deployment Accomplishments Fact Sheets

International Nuclear Information System (INIS)

WIBLE, R.A.

2001-01-01

Cleaning up the Hanford Site is one of the top priorities for the U. S. Department of Energy. The department is continually looking for ways to expedite cleanup and reduce costs. During Fiscal Year (FY) 2000. Hanford Site staff deployed 24 new technologies, which produced an estimated lifecycle cost savings of 479 million dollars. This is a clear indicator of the impacts new technology has had and will have on the cleanup efforts. The Hanford Site cleanup is focused on the following: Restoring the Columbia River Corridor; Building and operating the tank waste treatment complex to complete the cleanup of highly radioactive tank waste at Hanford; and Transitioning the Central Plateau. Applying innovative science and technology from national laboratories, universities, and private industry is critical to our complex cleanup mission. The 24 new technologies deployed in FY 2000 are significantly higher than our goal of 14 technological deployments. Eleven of these technologies supported restoring the Columbia River Corridor, and seven were involved with the remediation of radioactive tank waste. These deployments produced valuable information to determine the effectiveness of the new technologies in the field and the efficiencies gained over existing cleanup methods. In several cases, the technology deployed presented a solution to a problem where a clear path of remediation had not yet been determined. New and innovative technologies will play a significant role in the cleanup of the Hanford Site and enable remediation to be done more efficiently. Technology is being developed at a staggering pace. This requires excellent communication throughout the scientific and industry arenas. To effect this communication, we have implemented a technology needs process in conjunction with the multi-year work planning process. Through the combination of these two processes, technology developments and deployments address the near-term technology needs and enable us to plan for the

State perspectives on clean coal technology deployment

Energy Technology Data Exchange (ETDEWEB)

Moreland, T. [State of Illinois Washington Office, Washington, DC (United States)

1997-12-31

State governments have been funding partners in the Clean Coal Technology program since its beginnings. Today, regulatory and market uncertainties and tight budgets have reduced state investment in energy R and D, but states have developed program initiatives in support of deployment. State officials think that the federal government must continue to support these technologies in the deployment phase. Discussions of national energy policy must include attention to the Clean Coal Technology program and its accomplishments.

Structural damage detection robust against time synchronization errors

International Nuclear Information System (INIS)

Yan, Guirong; Dyke, Shirley J

2010-01-01

Structural damage detection based on wireless sensor networks can be affected significantly by time synchronization errors among sensors. Precise time synchronization of sensor nodes has been viewed as crucial for addressing this issue. However, precise time synchronization over a long period of time is often impractical in large wireless sensor networks due to two inherent challenges. First, time synchronization needs to be performed periodically, requiring frequent wireless communication among sensors at significant energy cost. Second, significant time synchronization errors may result from node failures which are likely to occur during long-term deployment over civil infrastructures. In this paper, a damage detection approach is proposed that is robust against time synchronization errors in wireless sensor networks. The paper first examines the ways in which time synchronization errors distort identified mode shapes, and then proposes a strategy for reducing distortion in the identified mode shapes. Modified values for these identified mode shapes are then used in conjunction with flexibility-based damage detection methods to localize damage. This alternative approach relaxes the need for frequent sensor synchronization and can tolerate significant time synchronization errors caused by node failures. The proposed approach is successfully demonstrated through numerical simulations and experimental tests in a lab

Post-deployment family violence among UK military personnel.

Science.gov (United States)

Kwan, Jamie; Jones, Margaret; Somaini, Greta; Hull, Lisa; Wessely, Simon; Fear, Nicola T; MacManus, Deirdre

2017-12-19

Research into violence among military personnel has not differentiated between stranger- and family-directed violence. While military factors (combat exposure and post-deployment mental health problems) are risk factors for general violence, there has been limited research on their impact on violence within the family environment. This study aims to compare the prevalence of family-directed and stranger-directed violence among a deployed sample of UK military personnel and to explore risk factors associated with both family- and stranger-directed violence. This study utilised data from a large cohort study which collected information by questionnaire from a representative sample of randomly selected deployed UK military personnel (n = 6711). The prevalence of family violence immediately following return from deployment was 3.6% and 7.8% for stranger violence. Family violence was significantly associated with having left service, while stranger violence was associated with younger age, male gender, being single, having a history of antisocial behaviour as well as having left service. Deployment in a combat role was significantly associated with both family and stranger violence after adjustment for confounders [adjusted odds ratio (aOR) = 1.92 (1.25-2.94), p = 0.003 and aOR = 1.77 (1.31-2.40), p violence both inside and outside the family environment and should be considered in violence reduction programmes for military personnel. Further research using a validated measurement tool for family violence would improve comparability with other research.

Progress in Precision Measurements of the Cosmic Microwave Background

Energy Technology Data Exchange (ETDEWEB)

Bernardis, P. de; Calvo, M.; Coppolecchia, A.; Cruciani, A.; Giordano, C.; Masi, S.; Nati, F.; Salatino, M.; Schillaci, A. [Dipartimento di Fisica, Universita La Sapienza, P.le A. Moro 2, 00185 Roma (Italy)

2011-08-15

High precision measurements of the Cosmic Microwave Background (CMB) represent one of the most difficult challenges in observational cosmology, but promise to unveil the mysteries of the very early Universe and of the birth of structures. Three observables are available. The small polarized CMB signal is probably carrying a signature of the early inflationary dynamics of the Universe. It is, however, embedded in overwhelming noise, systematic effects, and polarized foreground. The imprint of the large scale structure in the universe is present in the small-scale anisotropy of the CMB and in its spectral signatures (secondary anisotropy), again mixed with foreground contaminants. Low-level non-Gaussian components of CMB anisotropy and polarization also provide a very promising way to constrain inflation and the physics of ultra-high energies, if foregrounds can be efficiently separated from the measured signal. If measured with high precision, as required by the science issues above, the spectra of CMB anisotropy and polarization also constrain efficiently neutrino properties, hence their interest in this conference. Here we summarize the current status of CMB measurements, dominated by the Planck survey, and delineate the forthcoming activities, needed to exploit the huge scientific potential of precision measurements of the CMB, including the detection of neutrino masses.

Molecularly precise dendrimer-drug conjugates with tunable drug release for cancer therapy.

Science.gov (United States)

Zhou, Zhuxian; Ma, Xinpeng; Murphy, Caitlin J; Jin, Erlei; Sun, Qihang; Shen, Youqing; Van Kirk, Edward A; Murdoch, William J

2014-10-06

The structural preciseness of dendrimers makes them perfect drug delivery carriers, particularly in the form of dendrimer-drug conjugates. Current dendrimer-drug conjugates are synthesized by anchoring drug and functional moieties onto the dendrimer peripheral surface. However, functional groups exhibiting the same reactivity make it impossible to precisely control the number and the position of the functional groups and drug molecules anchored to the dendrimer surface. This structural heterogeneity causes variable pharmacokinetics, preventing such conjugates to be translational. Furthermore, the highly hydrophobic drug molecules anchored on the dendrimer periphery can interact with blood components and alter the pharmacokinetic behavior. To address these problems, we herein report molecularly precise dendrimer-drug conjugates with drug moieties buried inside the dendrimers. Surprisingly, the drug release rates of these conjugates were tailorable by the dendrimer generation, surface chemistry, and acidity. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Military deployment and reintegration: a systematic review of child coping.

Science.gov (United States)

Bello-Utu, Cindy F; DeSocio, Janiece E

2015-02-01

Child coping with parent military deployment and family reintegration. A systematic review of research literature was conducted to examine the effects of deployment and family reintegration on children in military families. A search of CINAHL, PubMed, Psyc-INFO, and SocINDEX databases was performed using the terms "military family," "military child," "child coping," "deployment," and "reintegration." The search was limited to publications between 2001 and 2014 to focus on the effects of Operation Enduring Freedom (OEF), Operation Iraqi Freedom (OIF), and Operation New Dawn (OND). Twenty-seven research reports met inclusion criteria. Three themes were extracted: A child's coping is influenced by (a) the child's age and development, (b) the mental health and coping of the non-deployed parent during deployment, and the mental health of both parents during family reintegration, and (c) the pre-existing resilience/vulnerability, cumulative risks, and resources of the child and family. © 2015 Wiley Periodicals, Inc.

Clinical Predictive Modeling Development and Deployment through FHIR Web Services.

Science.gov (United States)

Khalilia, Mohammed; Choi, Myung; Henderson, Amelia; Iyengar, Sneha; Braunstein, Mark; Sun, Jimeng

2015-01-01

Clinical predictive modeling involves two challenging tasks: model development and model deployment. In this paper we demonstrate a software architecture for developing and deploying clinical predictive models using web services via the Health Level 7 (HL7) Fast Healthcare Interoperability Resources (FHIR) standard. The services enable model development using electronic health records (EHRs) stored in OMOP CDM databases and model deployment for scoring individual patients through FHIR resources. The MIMIC2 ICU dataset and a synthetic outpatient dataset were transformed into OMOP CDM databases for predictive model development. The resulting predictive models are deployed as FHIR resources, which receive requests of patient information, perform prediction against the deployed predictive model and respond with prediction scores. To assess the practicality of this approach we evaluated the response and prediction time of the FHIR modeling web services. We found the system to be reasonably fast with one second total response time per patient prediction.

The Deployment of Product-Related Environmental Legislation into Product Requirements

Directory of Open Access Journals (Sweden)

Daniela C. A. Pigosso

2016-04-01

Full Text Available Environmental legislation is increasingly changing its focus from manufacturing-oriented to product-oriented instruments. Compliance with product-related environmental legislation is achieved by the incorporation of environmental requirements into the early phases of the product development process (PDP. Nevertheless, the deployment of product-related environmental legislation into product requirements is still a challenge. This study followed an inductive approach to propose a guideline to support the identification, analysis and deployment of product requirements based on product-related environmental legislation. The guideline is composed of nine steps, clustered into three groups according to their main objective: (A identification of environmental product-related legislation; (B identification of legislative topics to be considered for the deployment of requirements; and (C creation and validation of product requirements. The product requirements deployed are to be considered during the PDP. The guideline was evaluated in an expert consultation in a large manufacturing company, suggesting that it can be used to support the systematization and deployment of product-related environmental requirements.

Connected Vehicle Pilot Deployment Program phase 1 : comprehensive deployment plan : New York City : volume 1 : technical application : part I : technical and management approach.

Science.gov (United States)

2016-08-01

This document describes the Deployment Plan for the New York City Department of Transportation (NYC) Connected Vehicle Pilot Deployment (CVPD) Project. This plan describes the approach to complete Phase 2 Design/Build/Test, and Phase 3 Operate and Ma...

Hard is Normal: Military Families' Transitions Within the Process of Deployment.

Science.gov (United States)

Yablonsky, Abigail M; Barbero, Edie Devers; Richardson, Jeanita W

2016-02-01

US military deployments have become more frequent and lengthier in duration since 2003. Over half of US military members are married, and many also have children. The authors sought to understand the process of deployment from the perspective of the military family. After a thorough search of the literature, 21 primary research reports of 19 studies with an aggregate sample of 874 were analyzed using qualitative metasynthesis. The deployment process was experienced in four temporal domains. The military family as a whole shared the pre-deployment transition: all family members felt uncertain about the future, needed to complete tasks to "get ready" for deployment, and experienced a sense of distancing in preparation for the upcoming separation. The AD member went through the deployment transition independently, needing to "stay engaged" with the military mission, building a surrogate family and simultaneously trying to maintain connection with the family at home. In parallel, the home front family was going through a transposement transition, moving forward as an altered family unit, taking on new roles and responsibilities, and trying to simultaneously connect with the deployed member and find support from other military families. In post-deployment, the family went through the "reintegration" transition together, managing expectations, and readjusting family roles, all needing understanding and appreciation for their sacrifices during the recent separation. Effective family communication was important for military family well-being after deployment but unexpectedly challenging for many. Clinical, research, and policy recommendations are discussed. © 2015 Wiley Periodicals, Inc. This article has been contributed to by a US Government employee and her work is in the public domain in the USA.

Fiber-Optic Sensing System: Overview, Development and Deployment in Flight at NASA

Science.gov (United States)

Chan, Hon Man; Parker, Allen R.; Piazza, Anthony; Richards, W. Lance

2015-01-01

An overview of the research and technological development of the fiber-optic sensing system (FOSS) at the National Aeronautics and Space Administration Armstrong Flight Research Center (NASA AFRC) is presented. Theory behind fiber Bragg grating (FBG) sensors, as well as interrogation technique based on optical frequency domain reflectometry (OFDR) is discussed. Assessment and validation of FOSS as an accurate measurement tool for structural health monitoring is realized in the laboratory environment as well as large-scale flight deployment.

A Novel Methodology for Charging Station Deployment

Science.gov (United States)

Sun, Zhonghao; Zhao, Yunwei; He, Yueying; Li, Mingzhe

2018-02-01

Lack of charging stations has been a main obstacle to the promotion of electric vehicles. This paper studies deploying charging stations in traffic networks considering grid constraints to balance the charging demand and grid stability. First, we propose a statistical model for charging demand. Then we combine the charging demand model with power grid constraints and give the formulation of the charging station deployment problem. Finally, we propose a theoretical solution for the problem by transforming it to a Markov Decision Process.

Pulmonary Function and Respiratory Health of Military Personnel Before Southwest Asia Deployment.

Science.gov (United States)

Skabelund, Andrew J; Rawlins, Frederic A; McCann, Edward T; Lospinoso, Joshua A; Burroughs, Lorraine; Gallup, Roger A; Morris, Michael J

2017-09-01

Significant concern exists regarding the respiratory health of military personnel deployed to Southwest Asia, given their exposures to numerous environmental hazards. Although the deployed military force is generally assumed to be fit, the pre-deployment respiratory health of these individuals is largely unknown. Soldiers deploying to Southwest Asia were recruited from the pre-deployment processing center at Fort Hood, Texas. Participants completed a general and respiratory health questionnaire and performed baseline spirometry. One thousand six hundred ninety-three pre-deployment evaluations were completed. The average age of the participants was 32.2 y, and 83.1% were male. More than one third of surveyed solders had a smoking history, 73% were overweight or obese, and 6.2% reported a history of asthma. Abnormal spirometry was found in 22.3% of participants. Soldiers with abnormal spirometry reported more asthma (10.1% vs 5.1%, P military personnel that delineates factors potentially associated with the development of pulmonary symptoms and/or disease. This study suggests that deploying soldiers are older, heavier, frequently smoke, and may have undiagnosed pre-deployment lung disease. Abnormal spirometry is common but may not represent underlying disease. Self-reported asthma, wheezing, and slower 2-mile run times were predictive of abnormal spirometry. Pre-deployment evaluation of military personnel identified numerous soldiers with active pulmonary symptoms and abnormal spirometry. When combined with questions regarding asthma history, wheezing and exercise intolerance, spirometry may identify individuals at risk for deployment-related respiratory complaints. Copyright © 2017 by Daedalus Enterprises.

Optimizing Cloud-RAN Deployments in Real-life Scenarios Using Microwave Radio

DEFF Research Database (Denmark)

Al-obaidi, Rami; Checko, Aleksandra; Holm, Henrik

2015-01-01

Cloud Radio Access Network (C-RAN) is a new architecture designed to be the candidate for enabling future mobile networks. However, it will be deployed only if it is economically viable. In this paper we investigate the technological options of C-RAN deployments. By using analytical methods we...... derive engineering guidelines for minimizing the CAPital EXpenditure (CAPEX) of C-RAN deployment. We show for which population density and span of BBU Pool coverage usage of Microwave Radio (MWR) links is viable. For larger scale deployment we recommend to divide the area into multiple BBU Pools....

Assessing the PACE of California residential solar deployment: Impacts of Property Assessed Clean Energy programs on residential solar photovoltaic deployment in California, 2010-2015

Energy Technology Data Exchange (ETDEWEB)

Deason, Jeff; Murphy, Sean

2018-04-04

A new study by Berkeley Lab found that residential Property Assessed Clean Energy (R-PACE) programs increased deployment of residential solar photovoltaic (PV) systems in California, raising it by about 7-12% in cities that adopt these programs. R-PACE is a financing mechanism that uses a voluntary property tax assessment, paid off over time, to facilitate energy improvements and, in some jurisdictions, water and resilience measures. While previous studies demonstrated that early, regional R-PACE programs increased solar PV deployment, this new analysis is the first to demonstrate these impacts from the large, statewide R-PACE programs dominating the California market today, which use private capital to fund the upfront costs of the improvements. Berkeley Lab estimated the impacts using econometric techniques on two samples: -Large cities only, allowing annual demographic and economic data as control variables -All California cities, without these annual data Analysis of both samples controls for several factors other than R-PACE that would be expected to drive solar PV deployment. We infer that on average, cities with R-PACE programs were associated with greater solar PV deployment in our study period (2010-2015). In the large cities sample, solar PV deployment in jurisdictions with R-PACE programs was higher by 1.1 watts per owner-occupied household per month, or 12%. Across all cities, solar PV deployment in jurisdictions with R-PACE programs was higher by 0.6 watts per owner-occupied household per month, or 7%. The large cities results are statistically significant at conventional levels; the all-cities results are not. The estimates imply that the majority of solar PV deployment financed by R-PACE programs would likely not have occurred in their absence. Results suggest that R-PACE programs have increased PV deployment in California even in relatively recent years, as R-PACE programs have grown in market share and as alternate approaches for financing solar PV

Self managing monitoring for highly elastic large scale Cloud deployments

OpenAIRE

Ward, Jonathan Stuart; Barker, Adam David

2014-01-01

Infrastructure as a Service computing exhibits a number of properties, which are not found in conventional server deployments. Elasticity is among the most significant of these properties which has wide reaching implications for applications deployed in cloud hosted VMs. Among the applications affected by elasticity is monitoring. In this paper we investigate the challenges of monitoring large cloud deployments and how these challenges differ from previous monitoring problems. In order to mee...

Extremely deformable structures

CERN Document Server

2015-01-01

Recently, a new research stimulus has derived from the observation that soft structures, such as biological systems, but also rubber and gel, may work in a post critical regime, where elastic elements are subject to extreme deformations, though still exhibiting excellent mechanical performances. This is the realm of ‘extreme mechanics’, to which this book is addressed. The possibility of exploiting highly deformable structures opens new and unexpected technological possibilities. In particular, the challenge is the design of deformable and bi-stable mechanisms which can reach superior mechanical performances and can have a strong impact on several high-tech applications, including stretchable electronics, nanotube serpentines, deployable structures for aerospace engineering, cable deployment in the ocean, but also sensors and flexible actuators and vibration absorbers. Readers are introduced to a variety of interrelated topics involving the mechanics of extremely deformable structures, with emphasis on ...

Big Data’s Role in Precision Public Health

Science.gov (United States)

Dolley, Shawn

2018-01-01

Precision public health is an emerging practice to more granularly predict and understand public health risks and customize treatments for more specific and homogeneous subpopulations, often using new data, technologies, and methods. Big data is one element that has consistently helped to achieve these goals, through its ability to deliver to practitioners a volume and variety of structured or unstructured data not previously possible. Big data has enabled more widespread and specific research and trials of stratifying and segmenting populations at risk for a variety of health problems. Examples of success using big data are surveyed in surveillance and signal detection, predicting future risk, targeted interventions, and understanding disease. Using novel big data or big data approaches has risks that remain to be resolved. The continued growth in volume and variety of available data, decreased costs of data capture, and emerging computational methods mean big data success will likely be a required pillar of precision public health into the future. This review article aims to identify the precision public health use cases where big data has added value, identify classes of value that big data may bring, and outline the risks inherent in using big data in precision public health efforts. PMID:29594091

Deployment Methods for an Origami-Inspired Rigid-Foldable Array

Science.gov (United States)

Zirbel, Shannon A.; Trease, Brian P.; Magleby, Spencer P.; Howell, Larry L.

2014-01-01

The purpose of this work is to evaluate several deployment methods for an origami-inspired solar array at two size scales: 25-meter array and CubeSat array. The array enables rigid panel deployment and introduces new concepts for actuating CubeSat deployables. The design for the array was inspired by the origami flasher model (Lang, 1997; Shafer, 2001). Figure 1 shows the array prototyped from Garolite and Kapton film at the CubeSat scale. Prior work demonstrated that rigid panels like solar cells could successfully be folded into the final stowed configuration without requiring the panels to flex (Zirbel, Lang, Thomson, & al., 2013). The design of the array is novel and enables efficient use of space. The array can be wrapped around the central bus of the spacecraft in the case of the large array, or can accommodate storage of a small instrument payload in the case of the CubeSat array. The radial symmetry of this array around the spacecraft is ideally suited for spacecraft that need to spin. This work focuses on several actuation methods for a one-time deployment of the array. The array is launched in its stowed configuration and it will be deployed when it is in space. Concepts for both passive and active actuation were considered.

Biomarkers of post-deployment resilience among military service members

Directory of Open Access Journals (Sweden)

Krista B. Highland

2015-01-01

Full Text Available The development of PTSD after military deployment is influenced by a combination of biopsychosocial risk and resilience factors. In particular, physiological factors may mark risk for symptom progression or resiliency. Research in civilian populations suggests elevated catecholamines after trauma are associated with PTSD months following the trauma. However, less is known regarding physiological markers of PTSD resilience among post-deployment service members (SM. We therefore assessed whether catecholamines obtained shortly after deployment were associated with combat-related PTSD symptoms three months later. Eighty-seven SMs completed the Clinician-Administered PTSD Scale for DSM-IV and blood draws within two months after return from deployment to Iraq or Afghanistan (“Time 1” or “T1” and three months later (“Time 2” or “T2”. Linear regression analyses demonstrated that lower norepinephrine at T1 was associated with lower PTSD symptoms at T2. In particular, T1 norepinephrine was positively associated with T2 symptom intensity and avoidance symptoms. The present findings represent a biologically-informed method of assessing PTSD resilience after deployment, which may aid clinicians in providing tailored treatments for those in the greatest need. Further research is needed to validate these findings and incorporate physiological measures within an assessment battery.

Inflatable Tubular Structures Rigidized with Foams

Science.gov (United States)

Tinker, Michael L.; Schnell, Andrew R.

2010-01-01

Inflatable tubular structures that have annular cross sections rigidized with foams, and the means of erecting such structures in the field, are undergoing development. Although the development effort has focused on lightweight structural booms to be transported in compact form and deployed in outer space, the principles of design and fabrication are also potentially applicable to terrestrial structures, including components of ultralightweight aircraft, lightweight storage buildings and shelters, lightweight insulation, and sales displays. The use of foams to deploy and harden inflatable structures was first proposed as early as the 1960s, and has been investigated in recent years by NASA, the U.S. Air Force Research Laboratory, industry, and academia. In cases of deployable booms, most of the investigation in recent years has focused on solid cross sections, because they can be constructed relatively easily. However, solid-section foam-filled booms can be much too heavy for some applications. In contrast, booms with annular cross sections according to the present innovation can be tailored to obtain desired combinations of stiffness and weight through choice of diameters, wall thicknesses, and foam densities. By far the most compelling advantage afforded by this innovation is the possibility of drastically reducing weights while retaining or increasing the stiffnesses, relative to comparable booms that have solid foamfilled cross sections. A typical boom according to this innovation includes inner and outer polyimide film sleeves to contain foam that is injected between them during deployment.

Leadership and post-traumatic stress disorder: are soldiers' perceptions of organizational justice during deployment protective?

Science.gov (United States)

Elrond, Andreas F; Høgh, Annie; Andersen, Søren B

2018-01-01

Background : Soldiers' perception of leadership during military deployment has gained research attention as a potentially modifiable factor to buffer against the development of postdeployment post-traumatic stress disorder (PTSD). Within nonmilitary research, the organizational justice (OJ) framework, i.e. distributive justice, procedural justice (PJ) and interactional justice (IJ), has been found to relate to mental health outcomes. Aspects of OJ may, therefore, be protective against PTSD. Objectives : We examined the prospective relationship between aspects of OJ, namely the perceptions of PJ and IJ by subordinate soldiers without leadership obligations in relationship to immediate superiors and PTSD. Method : Participants were soldiers ( n =  245) deployed to Helmand Province in Afghanistan in 2009. Logistic regression procedures were used. The primary analysis measured PTSD cases using the Structured Clinical Interview for DSM-IV-TR Axis-I Disorder (SCID) 2½ years after homecoming. PJ/IJ was measured during deployment with a 6-item composite measure ranging from 0 to 12. Supplementary primary analyses were performed with PJ/IJ measured before and immediately after deployment. A secondary PJ/IJ analysis also tested against four postdeployment measures with the Post-Traumatic Stress Disorder Checklist Civilian (PCL-C) dichotomized at screening symptom levels. Results : Higher levels of perceived PJ/IJ for soldiers without leadership obligations during deployment had a prospective relation (OR = 0.86, 95% CI = 0.75-0.98) with PTSD on the SCID 2½ years after homecoming after adjustment for factors including predeployment PTSD symptoms, trauma and combat exposure, and state affectivity. Similar results were found by measuring PJ/IJ before (OR = 0.83, 95% CI = 0.71-0.95) but not immediately after homecoming (OR = 0.97, 95% CI = 0.85-1.11). A relationship with PTSD symptoms at the screening level at the four measurements of PCL-C was found, but only

Reduction of environmental impact by FR cycle deployment

International Nuclear Information System (INIS)

Katoh, Atsushi; Nakai, Ryodai

2005-03-01

In this report radioactive waste generations in terms of disposal volume or disposal field equivalent, and the radioactive toxicity of HLW are evaluated to clarify the promising nuclear scenario for the sake of realization of sustainable society in 21st century. This analysis was conducted based on the outcomes of the mass flow evaluation tool 'FAMILY-21' which calculates a material balance for TRU in the following scenarios. 1) LWR once-through scenario, 2) Pu partly recycling in LWR scenario, 3) Pu full recycling in LWR scenario, 4) FBR deployment scenario, 5) Interim storage scenario. The result shows that the cumulative area of low level radioactive waste (LLW) disposal field at 2150 in the FR cycle deployment scenario is 1.8 times larger than that in the LWR once-through scenario. The area of LLW disposal field at 2150 is a few km 2 in all the scenarios. In contrast, the cumulative area of high level radioactive waste (HLW) disposal field at 2150 in the FR cycle deployment scenario is less than half of that in the LWR once-through scenario. The area of HLW disposal field at 2150 is about 10 times of the area of LLW disposal field. Moreover, the FR deployment reduces the radioactive toxicity of HLW by U/TRU recycling, and shortens the period to decay under the natural Uranium toxicity level. Considering the area of radioactive waste disposal field and the radioactive toxicity of HLW, the advantage of the FR cycle deployment is indicated quantitatively from the viewpoint of the environmental burden reduction. (author)

Discursive Deployments: Mobilizing Support for Municipal and Community Wireless Networks in the U.S.

Energy Technology Data Exchange (ETDEWEB)

Alvarez, Rosio; Rodriguez, Juana Maria

2008-08-16

This paper examines Municipal Wireless (MW) deployments in the United States. In particular, the interest is in understanding how discourse has worked to mobilize widespread support for MW networks. We explore how local governments discursively deploy the language of social movements to create a shared understanding of the networking needs of communities. Through the process of"framing" local governments assign meaning to the MW networks in ways intended to mobilize support anddemobilize opposition. The mobilizing potential of a frame varies and is dependent on its centrality and cultural resonance. We examine the framing efforts of MW networks by using a sample of Request for Proposals for community wireless networks, semi-structured interviews and local media sources. Prominent values that are central to a majority of the projects and others that are culturally specific are identified and analyzed for their mobilizing potency.

Quality Function Deployment: Application to Chemotherapy Unit Services

Directory of Open Access Journals (Sweden)

Neda Hashemi

2015-10-01

Full Text Available Background: Today’s healthcare organizations are challenged by pressures to meet growing population demands and enhance community health through improving service quality. Quality function deployment is one of the widely-used customerdriven approaches for health services development. In the current study, quality function deployment is used to improve the quality of chemotherapy unit services. Methods: First, we identified chemotherapy outpatient unit patients as chemotherapy unit customers. Then, the Delphi technique and component factor analysis with orthogonal rotation was employed to determine their expectations. Thereafter, data envelopment analysis was performed to specify user priorities. We determined the relationships between patients’ expectations and service elements through expert group consensus using the Delphi method and the relationships between service elements by Pearson correlation. Finally, simple and compound priorities of the service elements were derived by matrix calculation. Results: Chemotherapy unit patients had four main expectations: access, suitable hotel services, satisfactory and effective relationships, and clinical services. The chemotherapy unit has six key service elements of equipment, materials, human resources, physical space, basic facilities, and communication and training. There were four-level relationships between the patients’ expectations and service elements, with mostly significant correlations between service elements. According to the findings, the functional group of basic facilities was the most critical factor, followed by materials. Conclusion: The findings of the current study can be a general guideline as well as a scientific, structured framework for chemotherapy unit decision makers in order to improve chemotherapy unit services.

University of Cambridge deploys Procket Networks' PRO/8801

CERN Multimedia

2003-01-01

Procket Networks, a provider of high performance Internet Protocol (IP) technology and products has announced that the University of Cambridge has deployed the PRO/8801(TM) router into its research network to develop industry-leading deep packet inspection applications. The major application for this deployment is to identify and understand new traffic patterns created by large scale scientific computations and downloads such as the GRID (1 page).

Cloud Environment Automation: from infrastructure deployment to application monitoring

Science.gov (United States)

Aiftimiei, C.; Costantini, A.; Bucchi, R.; Italiano, A.; Michelotto, D.; Panella, M.; Pergolesi, M.; Saletta, M.; Traldi, S.; Vistoli, C.; Zizzi, G.; Salomoni, D.

2017-10-01

The potential offered by the cloud paradigm is often limited by technical issues, rules and regulations. In particular, the activities related to the design and deployment of the Infrastructure as a Service (IaaS) cloud layer can be difficult to apply and time-consuming for the infrastructure maintainers. In this paper the research activity, carried out during the Open City Platform (OCP) research project [1], aimed at designing and developing an automatic tool for cloud-based IaaS deployment is presented. Open City Platform is an industrial research project funded by the Italian Ministry of University and Research (MIUR), started in 2014. It intends to research, develop and test new technological solutions open, interoperable and usable on-demand in the field of Cloud Computing, along with new sustainable organizational models that can be deployed for and adopted by the Public Administrations (PA). The presented work and the related outcomes are aimed at simplifying the deployment and maintenance of a complete IaaS cloud-based infrastructure.

Spacecraft on-orbit deployment anomalies - What can be done?

Science.gov (United States)

Freeman, Michael T.

1993-04-01

Modern communications satellites rely heavily upon deployable appendage (i.e. solar arrays, communications antennas, etc.) to perform vital functions that enable the spacecraft to effectively conduct mission objectives. Communications and telemetry antennas provide the radiofrequency link between the spacecraft and the earth ground station, permitting data to be transmitted and received from the satellite. Solar arrays serve as the principle source of electrical energy to the satellite, and recharge internal batteries during operation. However, since satellites cannot carry backup systems, if a solar array fails to deploy, the mission is lost. This article examines the subject of on-orbit anomalies related to the deployment of spacecraft appendage, and possible causes of such failures. Topics discussed shall include mechanical launch loading, on-orbit thermal and solar concerns, reliability of spacecraft pyrotechnics, and practical limitations of ground-based deployment testing. Of particular significance, the article will feature an in-depth look at the lessons learned from the successful recovery of the Telesat Canada Anik-E2 satellite in 1991.

Aerial Deployment and Inflation System for Mars Helium Balloons

Science.gov (United States)

Lachenmeler, Tim; Fairbrother, Debora; Shreves, Chris; Hall, Jeffery, L.; Kerzhanovich, Viktor V.; Pauken, Michael T.; Walsh, Gerald J.; White, Christopher V.

2009-01-01

A method is examined for safely deploying and inflating helium balloons for missions at Mars. The key for making it possible to deploy balloons that are light enough to be buoyant in the thin, Martian atmosphere is to mitigate the transient forces on the balloon that might tear it. A fully inflated Mars balloon has a diameter of 10 m, so it must be folded up for the trip to Mars, unfolded upon arrival, and then inflated with helium gas in the atmosphere. Safe entry into the Martian atmosphere requires the use of an aeroshell vehicle, which protects against severe heating and pressure loads associated with the hypersonic entry flight. Drag decelerates the aeroshell to supersonic speeds, then two parachutes deploy to slow the vehicle down to the needed safe speed of 25 to 35 m/s for balloon deployment. The parachute system descent dynamic pressure must be approximately 5 Pa or lower at an altitude of 4 km or more above the surface.

Perceptions of Individual and Family Functioning Among Deployed Female National Guard Members.

Science.gov (United States)

Kelly, Patricia J; Cheng, An-Lin; Berkel, LaVerne A; Nilsson, Johanna

2016-08-01

Females currently make up 15% of U.S. military service members. Minimal attention has been paid to families of female National Guard members who have been deployed and their subsequent reintegration challenges. This cross-sectional Internet-based survey of female members of four National Guard units compared those who were and were not deployed. Instruments, guided by the variables of the Family Resilience Model, measured individual, family, and deployment-related factors. Bivariate analysis and ordinal logistic regression were done to assess differences between the groups. Of the 239 National Guard members surveyed, deployed women (n = 164) had significantly higher levels of posttraumatic stress disorder (PTSD; p family functioning were higher among deployed when compared with never deployed women. Results indicate community interventions that focus on strengthening coping skills of female Guard members would be useful for this population. © The Author(s) 2016.

Deployment of SIP in MANET: challenges and circumvention

Directory of Open Access Journals (Sweden)

Abdelhamid Salma R.

2017-01-01

Full Text Available The immense growth in wireless network applications has encouraged the researchers to enhance and propose new approaches that facilitate the deployment of the widely used services, protocols, and applications of the wired networking area in the wireless networks. Among which, the Session Initiation Protocol (SIP is a signaling protocol that allows the establishment of multimedia sessions and calls between different parties. SIP functionality totally depends on a centralized infrastructure, and complexity arises when deploying such a protocol in a special type of wireless networks, namely Mobile Ad-hoc Networks (MANET, due to the absence of a centralized infrastructure, and the dynamic topology of the later. This paper highlights the the challenges arising when deploying SIP in MANETs and presents an overview of different proposed approaches to overcome these challenges.

Application of quality function deployment to the design of a lithium battery

Science.gov (United States)

Halbleib, L.; Wormington, P.; Cieslak, W.; Street, H.

Quality Function Deployment (QFD) is the tool we have selected to aid in the design, development and subsequent commercial manufacture of a Lithium/Thionyl Chloride 'D' cell for use in weapons applications. QFD is a structured methodology used to help assure that customer needs and expectations will be satisfied throughout the product life cycle. In this paper, we will describe our application of QFD, some of the lessons learned, and what we expect to be the final product of this QFD exercise.

A compact ultra-clean system for deploying radioactive sources inside the KamLAND detector

Science.gov (United States)

Banks, T. I.; Freedman, S. J.; Wallig, J.; Ybarrolaza, N.; Gando, A.; Gando, Y.; Ikeda, H.; Inoue, K.; Kishimoto, Y.; Koga, M.; Mitsui, T.; Nakamura, K.; Shimizu, I.; Shirai, J.; Suzuki, A.; Takemoto, Y.; Tamae, K.; Ueshima, K.; Watanabe, H.; Xu, B. D.; Yoshida, H.; Yoshida, S.; Kozlov, A.; Grant, C.; Keefer, G.; Piepke, A.; Bloxham, T.; Fujikawa, B. K.; Han, K.; Ichimura, K.; Murayama, H.; O`Donnell, T.; Steiner, H. M.; Winslow, L. A.; Dwyer, D. A.; McKeown, R. D.; Zhang, C.; Berger, B. E.; Lane, C. E.; Maricic, J.; Miletic, T.; Batygov, M.; Learned, J. G.; Matsuno, S.; Sakai, M.; Horton-Smith, G. A.; Downum, K. E.; Gratta, G.; Efremenko, Y.; Perevozchikov, O.; Karwowski, H. J.; Markoff, D. M.; Tornow, W.; Heeger, K. M.; Detwiler, J. A.; Enomoto, S.; Decowski, M. P.

2015-01-01

We describe a compact, ultra-clean device used to deploy radioactive sources along the vertical axis of the KamLAND liquid-scintillator neutrino detector for purposes of calibration. The device worked by paying out and reeling in precise lengths of a hanging, small-gauge wire rope (cable); an assortment of interchangeable radioactive sources could be attached to a weight at the end of the cable. All components exposed to the radiopure liquid scintillator were made of chemically compatible UHV-cleaned materials, primarily stainless steel, in order to avoid contaminating or degrading the scintillator. To prevent radon intrusion, the apparatus was enclosed in a hermetically sealed housing inside a glove box, and both volumes were regularly flushed with purified nitrogen gas. An infrared camera attached to the side of the housing permitted real-time visual monitoring of the cable's motion, and the system was controlled via a graphical user interface.

A compact ultra-clean system for deploying radioactive sources inside the KamLAND detector

Energy Technology Data Exchange (ETDEWEB)

Banks, T.I., E-mail: tbanks@berkeley.edu [Physics Department, University of California, Berkeley, CA 94720 (United States); Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Freedman, S.J. [Physics Department, University of California, Berkeley, CA 94720 (United States); Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Kavli Institute for the Physics and Mathematics of the Universe (WPI), University of Tokyo, Kashiwa, Chiba 277-8583 (Japan); Wallig, J.; Ybarrolaza, N. [Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Gando, A.; Gando, Y.; Ikeda, H. [Research Center for Neutrino Science, Tohoku University, Sendai 980-8578 (Japan); Inoue, K. [Research Center for Neutrino Science, Tohoku University, Sendai 980-8578 (Japan); Kavli Institute for the Physics and Mathematics of the Universe (WPI), University of Tokyo, Kashiwa, Chiba 277-8583 (Japan); Kishimoto, Y. [Kavli Institute for the Physics and Mathematics of the Universe (WPI), University of Tokyo, Kashiwa, Chiba 277-8583 (Japan); Research Center for Neutrino Science, Tohoku University, Sendai 980-8578 (Japan); Koga, M. [Research Center for Neutrino Science, Tohoku University, Sendai 980-8578 (Japan); Kavli Institute for the Physics and Mathematics of the Universe (WPI), University of Tokyo, Kashiwa, Chiba 277-8583 (Japan); Mitsui, T. [Research Center for Neutrino Science, Tohoku University, Sendai 980-8578 (Japan); Nakamura, K. [Research Center for Neutrino Science, Tohoku University, Sendai 980-8578 (Japan); Kavli Institute for the Physics and Mathematics of the Universe (WPI), University of Tokyo, Kashiwa, Chiba 277-8583 (Japan); Shimizu, I.; Shirai, J.; Suzuki, A.; Takemoto, Y.; Tamae, K.; Ueshima, K.; Watanabe, H.; Xu, B.D. [Research Center for Neutrino Science, Tohoku University, Sendai 980-8578 (Japan); and others

2015-01-01

We describe a compact, ultra-clean device used to deploy radioactive sources along the vertical axis of the KamLAND liquid-scintillator neutrino detector for purposes of calibration. The device worked by paying out and reeling in precise lengths of a hanging, small-gauge wire rope (cable); an assortment of interchangeable radioactive sources could be attached to a weight at the end of the cable. All components exposed to the radiopure liquid scintillator were made of chemically compatible UHV-cleaned materials, primarily stainless steel, in order to avoid contaminating or degrading the scintillator. To prevent radon intrusion, the apparatus was enclosed in a hermetically sealed housing inside a glove box, and both volumes were regularly flushed with purified nitrogen gas. An infrared camera attached to the side of the housing permitted real-time visual monitoring of the cable's motion, and the system was controlled via a graphical user interface.

Tailor-made nano-structured materials for perpendicular recording media and head-precise control of direct/indirect exchange coupling

International Nuclear Information System (INIS)

Takahashi, Migaku; Tsunoda, Masakiyo; Saito, Shin

2009-01-01

Tailor-made nano-structured spin materials obtained by precisely controlled nano-scale fabrication technologies for use in ultra-high density hard disk drives (HDDs), as well as an understanding of their nanomagnetics, are essential from the view point of materials, processes, and physics. Artificial control of the exchange coupling among ferromagnetic layers through the RKKY interaction (indirect) and direct exchange coupling represented as the exchange bias at the ferromagnetic (FM)/antiferromagnetic (AFM) interface are of great interest and have received significant attention to induce new modulated spin structures in conventional simple FM materials. In particular, soft magnetic under layer (SUL) with strong synthetic antiferromagnetic (SAF) coupling between two adjacent soft magnetic layers, exchange coupled stacked media introducing exchange coupling between FM layers and giant exchange anisotropy at the FM/AFM interface have attracted significant attention from the view point of applications. Within the framework of the present paper, we discuss future technical trends for SUL, granular media and the spin-valve head from the viewpoint of direct and/or indirect exchange coupling based on our recent results

Seismic analysis of ITER multi-purpose deployer

International Nuclear Information System (INIS)

Manuelraj, Manoah Stephen; Gotewal, Krishan Kumar; Dutta, Pramit; Rastogi, Naveen; Choi, Chang-Hwan; Tesini, Alessandro

2015-01-01

The Multi-Purpose Deployer (MPD) is a general purpose ITER in-vessel remote handling (RH) system. The MPD will perform various in-vessel maintenance tasks such as dust and tritium inventory control, in-service inspection, leak localization and in-vessel diagnostics maintenance. The main handling equipment, called as the MPD Transporter, consists of a series of linked bodies, which provide anchoring to the vacuum vessel port and an articulated multi-degree of freedom motion to perform the aforementioned tasks. The target payload for the MPD Transporter is 2 tons. The total length is 16.6 m and 18.1 m for short and long configuration respectively, while the total weight of the system is about 25.5 tons including the payload. During the in-vessel operations, the structural integrity of the system should be guaranteed against various operational and seismic loads. This paper presents the seismic structural analysis results of the concept design of the MPD Transporter. Static structural, modal and frequency response spectrum analyses have been performed to verify the structural integrity of the MPD itself, and to provide reaction loads to the interfacing systems such as vacuum vessel and cask. The analyses are carried out by using the ANSYS. The first analysis iteration was carried out for the reference design of the MPD Transporter, which showed stresses higher than the permissible limit. Structural optimizations and reinforcements were performed for individual bodies referring the stress levels in each body, and a reinforced design was proposed. The reinforced design satisfies the required structural criteria in terms of general global stresses. Though local stress concentrations were observed, it can be solved in the next design phase by further local reinforcements or proper material choice. (author)

50 CFR 635.21 - Gear operation and deployment restrictions.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 8 2010-10-01 2010-10-01 false Gear operation and deployment restrictions....21 Gear operation and deployment restrictions. Link to an amendment published at 75 FR 57701, Sept. 22, 2010. The green-stick gear authorization requirements under paragraphs (c)(2)(v)(A), (c)(2)(v)(B...

FBR/VHTR deployment scenarios in Japan

International Nuclear Information System (INIS)

Richards, Matt; Kunitomi, Kazuhiko

2008-01-01

Co-deployment of Fast Breeder Reactors (FBRs) and Very High Temperature Reactors (VHTRs) can be used as the nuclear technologies to meet a significant portion of Japan's future energy demands. The FBR provides the fissile fuel for energy security and sustainability, and can be used to provide a significant portion of the electricity demand. The VHTR can provide flexible energy outputs (electricity, hydrogen, and high-temperature heat) with high efficiency, can operate with a wide variety of fuel cycles, and can be sited at locations that have limited availability of cooling water. These features, combined with its passive safety and high degree of proliferation resistance, make the VHTR an ideal complement for co-deployment with the FBR in Japan and also a very low-risk technology of export to foreign countries. In addition to hydrogen production, the high-temperature thermal energy produced by the VHTR fleet can be used for a wide variety of process-heat applications, and the VHTR can play a key role for significantly reducing greenhouse-gas emissions. This paper describes assessments for deploying FBRs and VHTRs in Japan using a closed fuel cycle, with the FBRs supplying the fissile material to sustain the combined FBR/VHTR fleet. (author)

Impact of Federal Tax Policy on Utility-Scale Solar Deployment Given Financing Interactions

Energy Technology Data Exchange (ETDEWEB)

Mai, Trieu; Cole, Wesley; Krishnan, Venkat; Bolinger, Mark

2015-09-28

In this study, the authors conducted a literature review of approaches and assumptions used by other modeling teams and consultants with respect to solar project financing; developed and incorporated an ability to model the likely financing shift away from more expensive sources of capital and toward cheaper sources as the investment tax credit declines in the ReEDS model; and used the 'before and after' versions of the ReEDS model to isolate and analyze the deployment impact of the financing shift under a range of conditions. Using ReEDS scenarios with this improved capability, we find that this 'financing' shift would soften the blow of the ITC reversion; however, the overall impacts of such a shift in capital structure are estimated to be small and near-term utility-scale PV deployment is found to be much more sensitive to other factors that might drive down utility-scale PV prices.

Logistics analysis to Improve Deployability (LOG-AID): Field Experiment/Results

National Research Council Canada - National Science Library

Evers, Kenneth

2000-01-01

.... Under sponsorship of the Air Force Research Laboratory Logistics Readiness Branch (AFRL/HESR), the Synergy team analyzed the current wing-level deployment process as part of the Logistics Analysis to Improve Deployability (LOG-AID) program...

Histological Diagnoses of Military Personnel Undergoing Lung Biopsy After Deployment to Southwest Asia.

Science.gov (United States)

Madar, Cristian S; Lewin-Smith, Michael R; Franks, Teri J; Harley, Russell A; Klaric, John S; Morris, Michael J

2017-08-01

The current understanding of associations between lung disease and military deployment to Southwest Asia, including Iraq and Afghanistan, is both controversial and limited. We sought to clarify the relation between military deployment and biopsy-proven lung disease. Retrospective data were analyzed for military personnel with non-neoplastic lung biopsies evaluated at the Armed Forces Institute of Pathology or Joint Pathology Center (January 2005 to December 2012). Of 391 subjects, 137 (35.0%) had deployed to Southwest Asia prior to biopsy. Compared to non-deployed subjects, those deployed were younger (median age 37 vs. 51 years) with higher representation of African Americans (30.0 vs. 16.9%). Deployed patients were more likely diagnosed with non-necrotizing granulomas (OR 2.4). Non-deployed subjects had higher frequency of idiopathic interstitial pneumonias, particularly organizing pneumonia. Prevalence of small airways diseases including constrictive bronchiolitis was low. This study provides a broader understanding of diversity of biopsy-proven non-neoplastic lung disease as it relates to military deployment to Southwest Asia and importantly did not show an increased prevalence of small airway disease to include constrictive bronchiolitis.

Vibration control for precision manufacturing at Sandia National Laboratories

International Nuclear Information System (INIS)

Hinnerichs, T.; Martinez, D.

1995-01-01

Sandia National Laboratories performs R and D in structural dynamics and vibration suppression for precision applications in weapon systems, space, underwater, transportation and civil structures. Over the last decade these efforts have expanded into the areas of active vibration control and ''smart'' structures and material systems. In addition, Sandia has focused major resources towards technology to support weapon product development and agile manufacturing capability for defense and industrial applications. This paper will briefly describe the structural dynamics modeling and verification process currently in place at Sandia that supports vibration control and some specific applications of these techniques to manufacturing in the areas of lithography, machine tools and flexible robotics

Vibration control for precision manufacturing at Sandia National Laboratories

Energy Technology Data Exchange (ETDEWEB)

Hinnerichs, T.; Martinez, D. [Sandia National Labs., Albuquerque, NM (United States). Structural Dynamics and Vibration Control Dept.

1995-04-01

Sandia National Laboratories performs R and D in structural dynamics and vibration suppression for precision applications in weapon systems, space, underwater, transportation and civil structures. Over the last decade these efforts have expanded into the areas of active vibration control and ``smart`` structures and material systems. In addition, Sandia has focused major resources towards technology to support weapon product development and agile manufacturing capability for defense and industrial applications. This paper will briefly describe the structural dynamics modeling and verification process currently in place at Sandia that supports vibration control and some specific applications of these techniques to manufacturing in the areas of lithography, machine tools and flexible robotics.

Effects of combat deployment on risky and self-destructive behavior among active duty military personnel.

Science.gov (United States)

Thomsen, Cynthia J; Stander, Valerie A; McWhorter, Stephanie K; Rabenhorst, Mandy M; Milner, Joel S

2011-10-01

Although research has documented negative effects of combat deployment on mental health, few studies have examined whether deployment increases risky or self-destructive behavior. The present study addressed this issue. In addition, we examined whether deployment effects on risky behavior varied depending on history of pre-deployment risky behavior, and assessed whether psychiatric conditions mediated effects of deployment on risky behavior. In an anonymous survey, active duty members of the U.S. Marine Corps and U.S. Navy (N = 2116) described their deployment experiences and their participation in risky recreational activities, unprotected sex, illegal drug use, self-injurious behavior, and suicide attempts during three time frames (civilian, military pre-deployment, and military post-deployment). Respondents also reported whether they had problems with depression, anxiety, or PTSD during the same three time frames. Results revealed that risky behavior was much more common in civilian than in military life, with personnel who had not deployed, compared to those who had deployed, reporting more risky behavior and more psychiatric problems as civilians. For the current time period, in contrast, personnel who had deployed (versus never deployed) were significantly more likely to report both risky behavior and psychiatric problems. Importantly, deployment was associated with increases in risky behavior only for personnel with a pre-deployment history of engaging in risky behavior. Although psychiatric conditions were associated with higher levels of risky behavior, psychiatric problems did not mediate associations between deployment and risky behavior. Implications for understanding effects of combat deployment on active duty personnel and directions for future research are discussed. Published by Elsevier Ltd.

Dynamical Coordination of Hand Intrinsic Muscles for Precision Grip in Diabetes Mellitus.

Science.gov (United States)

Li, Ke; Wei, Na; Cheng, Mei; Hou, Xingguo; Song, Jun

2018-03-12

This study investigated the effects of diabetes mellitus (DM) on dynamical coordination of hand intrinsic muscles during precision grip. Precision grip was tested using a custom designed apparatus with stable and unstable loads, during which the surface electromyographic (sEMG) signals of the abductor pollicis brevis (APB) and first dorsal interosseous (FDI) were recorded simultaneously. Recurrence quantification analysis (RQA) was applied to quantify the dynamical structure of sEMG signals of the APB and FDI; and cross recurrence quantification analysis (CRQA) was used to assess the intermuscular coupling between the two intrinsic muscles. This study revealed that the DM altered the dynamical structure of muscle activation for the FDI and the dynamical intermuscular coordination between the APB and FDI during precision grip. A reinforced feedforward mechanism that compensates the loss of sensory feedbacks in DM may be responsible for the stronger intermuscular coupling between the APB and FDI muscles. Sensory deficits in DM remarkably decreased the capacity of online motor adjustment based on sensory feedback, rendering a lower adaptability to the uncertainty of environment. This study shed light on inherent dynamical properties underlying the intrinsic muscle activation and intermuscular coordination for precision grip and the effects of DM on hand sensorimotor function.

High-precision multiband spectroscopy of ultracold fermions in a nonseparable optical lattice

Science.gov (United States)

Fläschner, Nick; Tarnowski, Matthias; Rem, Benno S.; Vogel, Dominik; Sengstock, Klaus; Weitenberg, Christof

2018-05-01

Spectroscopic tools are fundamental for the understanding of complex quantum systems. Here, we demonstrate high-precision multiband spectroscopy in a graphenelike lattice using ultracold fermionic atoms. From the measured band structure, we characterize the underlying lattice potential with a relative error of 1.2 ×10-3 . Such a precise characterization of complex lattice potentials is an important step towards precision measurements of quantum many-body systems. Furthermore, we explain the excitation strengths into different bands with a model and experimentally study their dependency on the symmetry of the perturbation operator. This insight suggests the excitation strengths as a suitable observable for interaction effects on the eigenstates.

A scope of the problem: Post-deployment reintegration challenges in a National Guard Unit.

Science.gov (United States)

Wilcox, Sherrie L; Oh, Hyunsung; Redmond, Sarah A; Chicas, Joseph; Hassan, Anthony M; Lee, Pey-Jiuan; Ell, Kathleen

2015-01-01

More Reserve and Guard members have been activated in the past few years than in any other time in history. In addition to the high rates of psychological and behavioral challenges among military personnel, there are other equally important post-deployment reintegration challenges. Post-deployment reintegration challenges are particularly important to Reserve and Guard members, who transition rapidly from civilian-military-civilian. This study aims to describe the scope of challenges that a battalion of National Guard members (NGM) report experiencing after returning from a one-year deployment to Iraq. This article reports data from a sample of 126 NGM who recently returned from a one-year deployment to Iraq. The scope of post-deployment problems at baseline, 3- and 6-month post-deployment are presented. Overall, the rates of post-deployment psychological and behavioral problems were elevated upon returning from deployment and remained fairly constant for up to 6 months post-deployment. Approximately 30% of respondents were unsatisfied with their relationship and upwards of 30% reported family reintegration challenges. Comparisons with similar research and implications for prevention and improvement of post-deployment quality of life are addressed.

Deployment, Design, and Commercialization of Carbon-Negative Energy Systems

Science.gov (United States)

Sanchez, Daniel Lucio

Climate change mitigation requires gigaton-scale carbon dioxide removal technologies, yet few examples exist beyond niche markets. This dissertation informs large-scale implementation of bioenergy with carbon capture and sequestration (BECCS), a carbon-negative energy technology. It builds on existing literature with a novel focus on deployment, design, commercialization, and communication of BECCS. BECCS, combined with aggressive renewable deployment and fossil emission reductions, can enable a carbon-negative power system in Western North America by 2050, with up to 145% emissions reduction from 1990 levels. BECCS complements other sources of renewable energy, and can be deployed in a manner consistent with regional policies and design considerations. The amount of biomass resource available limits the level of fossil CO2 emissions that can still satisfy carbon emissions caps. Offsets produced by BECCS are more valuable to the power system than the electricity it provides. Implied costs of carbon for BECCS are relatively low ( 75/ton CO2 at scale) for a capital-intensive technology. Optimal scales for BECCS are an order of magnitude larger than proposed scales found in existing literature. Deviations from optimal scaled size have little effect on overall systems costs - suggesting that other factors, including regulatory, political, or logistical considerations, may ultimately have a greater influence on plant size than the techno-economic factors considered. The flexibility of thermochemical conversion enables a viable transition pathway for firms, utilities and governments to achieve net-negative CO 2 emissions in production of electricity and fuels given increasingly stringent climate policy. Primary research, development (R&D), and deployment needs are in large-scale biomass logistics, gasification, gas cleaning, and geological CO2 storage. R&D programs, subsidies, and policy that recognize co-conversion processes can support this pathway to commercialization

Elastic dynamic research of high speed multi-link precision press considering structural stiffness of rotation joints

Energy Technology Data Exchange (ETDEWEB)

Hu, Feng Feng; Sun, Yu; Peng, Bin Bin [School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing (China)

2016-10-15

An elastic dynamic model of high-speed multi-link precision press considering structural stiffness of rotation joints was established by the finite element method. In the finite element model, rotation joint was established by four bar elements with equivalent stiffness, and connected link was established by beam element. Then, the elastic dynamics equation of the system was established, and modal superposition method was used to solve the dynamic response. Compared with the traditional elastic dynamic model with perfect constraint of the rotation joints, the elastic dynamic response value of the improved model is larger. To validate the presented new method of elastic dynamics analysis with stiffness of rotation joints, a related test of slider Bottom dead center (BDC) position in different speed was designed. The test shows that the model with stiffness of rotation joints is more reasonable. So it provides a reasonable theory and method for dynamic characteristics research of such a multi-link machine.

The impact of state financial incentives on market deployment of solar technology

International Nuclear Information System (INIS)

Sarzynski, Andrea; Larrieu, Jeremy; Shrimali, Gireesh

2012-01-01

Many states have adopted financial incentives to encourage market deployment of solar energy technology. This paper employs a cross-sectional time-series approach to evaluate the extent to which state solar financial incentives systematically encouraged market deployment of solar photovoltaic (PV) technology from 1997 to 2009. The results demonstrate that states offering cash incentives such as rebates and grants experienced more extensive and rapid deployment of grid-tied PV technology than states without cash incentives over the study period. The analysis also finds that the presence of state renewable energy portfolio standards and specific solar carve-out provisions within them heavily influenced the market deployment of grid-tied solar PV technology through 2009. - Highlights: ► We evaluate the impact of state financial incentives on solar technology adoption. ► Cash incentives and renewable portfolio standards strongly influenced deployment. ► The impact of cash incentives and RPS grew significantly over time. ► Tax incentives had little systematic effect on solar market deployment.

Preparing British Military nurses to deliver nursing care on deployment. An Afghanistan study.

Science.gov (United States)

Finnegan, Alan; Finnegan, Sara; Bates, David; Ritsperis, Debra; McCourt, Kath; Thomas, Mike

2015-01-01

This paper forms part of the first British Armed forces qualitative nursing research study undertaken on deployment. To provide an analysis of the impact and effectiveness of the pre-deployment educational preparation and clinical placements provided for military nurses. A Constructivist Grounded Theory was utilised with data collected through semi-structured interviews with 18 nurses based in Camp Bastion Hospital, Afghanistan during 2013. Initial coding indicated 21 educational preparation and clinical placement categories that influenced the delivery of nursing care. Analysis of these elements led to the identification of four major clusters: Military Nursing Care; Military Nurse Education; Unique Hospital Environment and Clinical Placements. Educational preparation consists of completing deployable operational nursing competencies, specialist training and individual tailored courses. This strategy was viewed as proving the appropriate academic requirement. However, training would be enhanced by introducing a formalised military preceptorship programme focussing on fundamental nursing skills. Caring for children was a particular concern, and it was emphasised that educational courses must be combined with a standardised clinical placement policy. Adequate clinical exposure can be challenging as nurses are not routinely exposed to War Zone levels of trauma in the UK. Clinical placements need to be standardised and harmonised, and located in areas where nurses cared for patients with similar injury patterns to those witnessed on deployment. Current NHS Trust placements can reduce the opportunities for employment in suitable clinical environments and diminishing the openings for collective military training. Better use should be made of clinical rotation programmes, including high dependency units, elective surgery, medical assessment units, paediatrics, and outreach teams such as burns and plastic surgery and pain management. Practice Educators should be utilised

A Conceptual Design for a Small Deployer Satellite

Science.gov (United States)

Zumbo, S.

2002-01-01

industrial partners, has started the development of a space mission, named DeSat, focused on a new highly innovative micro satellite bus for LEO, entirely designed by an integrated team of students and researchers. The first mission is scheduled to fly at the end of 2003 on a converted Russian ICBM. The paper is intended to present the main features of DeSat mission, its goals and the activities that have been done by students and researchers to achieve the micro satellite platform design. The principal payload of the entire system is represented by a recirculating ball screw boom whose mass reaches one third of the total mass budget. The goal of the mission is to demonstrate the validity of its design also for space applications, which may range from precise off platform positioning of devices and instruments to GPS interferometry, sensor measurements and robotics. The satellite geometry, when the boom is in deployed configuration, is so stretched that the name "deployable satellite" has come out naturally. The large deployment mechanism, compared to the small bus, has influenced the design of every satellite subsystem leading to innovative solutions in terms of design, materials, equipment and instruments.

Antihydrogen production and precision experiments

International Nuclear Information System (INIS)

Nieto, M.M.; Goldman, T.; Holzscheiter, M.H.

1996-01-01

The study of CPT invariance with the highest achievable precision in all particle sectors is of fundamental importance for physics. Equally important is the question of the gravitational acceleration of antimatter. In recent years, impressive progress has been achieved in capturing antiprotons in specially designed Penning traps, in cooling them to energies of a few milli-electron volts, and in storing them for hours in a small volume of space. Positrons have been accumulated in large numbers in similar traps, and low energy positron or positronium beams have been generated. Finally, steady progress has been made in trapping and cooling neutral atoms. Thus the ingredients to form antihydrogen at rest are at hand. Once antihydrogen atoms have been captured at low energy, spectroscopic methods can be applied to interrogate their atomic structure with extremely high precision and compare it to its normal matter counterpart, the hydrogen atom. Especially the 1S-2S transition, with a lifetime of the excited state of 122 msec and thereby a natural linewidth of 5 parts in 10 16 , offers in principle the possibility to directly compare matter and antimatter properties at a level of 1 part in 10 16

[Precision and personalized medicine].

Science.gov (United States)

Sipka, Sándor

2016-10-01

The author describes the concept of "personalized medicine" and the newly introduced "precision medicine". "Precision medicine" applies the terms of "phenotype", "endotype" and "biomarker" in order to characterize more precisely the various diseases. Using "biomarkers" the homogeneous type of a disease (a "phenotype") can be divided into subgroups called "endotypes" requiring different forms of treatment and financing. The good results of "precision medicine" have become especially apparent in relation with allergic and autoimmune diseases. The application of this new way of thinking is going to be necessary in Hungary, too, in the near future for participants, controllers and financing boards of healthcare. Orv. Hetil., 2016, 157(44), 1739-1741.

Use of the Air Force Post-Deployment Health Reassessment for the identification of depression and posttraumatic stress disorder: public health implications for suicide prevention.

Science.gov (United States)

McCarthy, Michael D; Thompson, Sanna J; Knox, Kerry L

2012-03-01

Military members are required to complete the Post-Deployment Health Assessment on return from deployment and the Post-Deployment Health Reassessment (PHDRA) 90 to 180 days later, and we assessed the PDHRA's sensitivity and specificity in identifying posttraumatic stress disorder (PTSD) and depression after a military deployment among US Air Force personnel. We computed the PDHRA's sensitivity and specificity for depression and PTSD and developed a structural model to suggest possible improvements to it. For depression, sensitivity and specificity were 0.704 and 0.651, respectively; for PTSD, they were 0.774 and 0.650, respectively. Several variables produced significant direct effects on depression and trauma, suggesting that modifications could increase its sensitivity and specificity. The PDHRA was moderately effective in identifying airmen with depression and PTSD. It identified behavioral health concerns in many airmen who did not develop a diagnostic mental health condition. Its low level of specificity may result in reduced barriers to care and increased support services, key components of a public health approach to suicide prevention, for airmen experiencing subacute levels of distress after deployment, which may, in part, account for lower suicide rates among airmen after deployment.

RadNet Air Quality (Deployable) Data

Data.gov (United States)

U.S. Environmental Protection Agency — RadNet Deployable Monitoring is designed to collect radiological and meteorological information and data asset needed to establish the impact of radiation levels on...

Structure and seismicity of the upper mantle using deployments of broadband seismographs in Antarctica and the Mariana Islands

Science.gov (United States)

Barklage, Mitchell

. We investigate seismic velocity structure of the upper mantle across the Central Mariana subduction system using data from the 2003-2004 Mariana Subduction Factory Imaging Experiment. This 11-month experiment consisted of 20 broadband seismic stations deployed on islands and 58 semi-broadband ocean bottom seismographs deployed across the forearc, island arc, and back-arc spreading center. We determine Vp and Vp/Vs structure on a three dimensional grid using over 25,000 local travel time observations as well as over 2000 teleseismic arrival times determined by waveform cross correlation. The mantle wedge is characterized by a region of low velocity and high Vp/Vs beneath the forearc, an inclined zone of low velocity underlying the volcanic front, and a broad region of low velocity beneath the back-arc spreading center. The slow velocity anomalies are strongest at roughly 20-30 km depth in the forearc, 60-70 km depth beneath the volcanic arc, and 20-30 km beneath the back-arc spreading center. The slow velocity anomalies beneath the arc and back-arc appear as separate and distinct features in our images, with a small channel of connectivity occurring at approximately 75 km depth. The subducting Pacific plate is characterized by high seismic velocities. An exception occurs in the forearc beneath the big blue seamount and at the top of the slab at roughly 80 km depth where slow velocities are observed. We interpret the forearc anomalies to represent a region of large scale serpentinization of the mantle whereas the arc and back-arc anomalies represent regions of high temperature with a small amount of increased water content and/or melt and constrain the source regions in the mantle for arc and back-arc lavas. We investigate the double seismic zone (dsz) beneath the Central Mariana Arc using data from a land-sea array of 58 ocean bottom seismographs and 20 land seismographs deployed during 2003-2004. Nearly 600 well-recorded earthquakes were located using a P and S wave

The newest precision measurement

International Nuclear Information System (INIS)

Lee, Jing Gu; Lee, Jong Dae

1974-05-01

This book introduces basic of precision measurement, measurement of length, limit gauge, measurement of angles, measurement of surface roughness, measurement of shapes and locations, measurement of outline, measurement of external and internal thread, gear testing, accuracy inspection of machine tools, three dimension coordinate measuring machine, digitalisation of precision measurement, automation of precision measurement, measurement of cutting tools, measurement using laser, and point of choosing length measuring instrument.

Vibration characteristics of a deployable controllable-geometry truss boom

Science.gov (United States)

Dorsey, J. T.

1983-01-01

An analytical study was made to evaluate changes in the fundamental frequency of a two dimensional cantilevered truss boom at various stages of deployment. The truss could be axially deployed or retracted and undergo a variety of controlled geometry changes by shortening or lengthening the telescoping diagonal members in each bay. Both untapered and tapered versions of the truss boom were modeled and analyzed by using the finite element method. Large reductions in fundamental frequency occurred for both the untapered and tapered trusses when they were uniformly retracted or maneuvered laterally from their fully deployed position. These frequency reductions can be minimized, however, if truss geometries are selected which maintain cantilever root stiffness during truss maneuvers.

Fiscal 1994 technological survey report. Research study on polymer materials by precision polymerization; 1994 nendo seimitsu jugo kobunshi zairyo ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

In the paradigm that propelled polymer chemistry, there are involved the establishment of polymer concept, engineering plastics, regulation of higher ordered structure, and precision polymerization. The first two produced the polymer chemistry era in the 20th century. The regulation of higher ordered structure and the precision polymerization are the fundamental technologies supporting the polymer chemistry of the 21st century. The precision polymerization is a technology for regulating the stereospecificity, sequential structure, and molecular weight of polymers by regulating atoms and molecules and is referred to the following important techniques to be concrete. In the precision addition polymerization, stereospecific regulation and purification of active site to give living polymers are required while, in the precision condensation polymerization, regulation of condensation probability process to be secondary Marcov chain is necessary, as is the establishment of non-defect condensation condition avoiding high temperature deterioration and the like. In the biomimetic precision polymerization, key issues are the method of incorporating molecular recognition control and sequential structure control by living organs into an industrial process. If the higher ordered structure can be regulated by the precision polymerization, it is possible to obtain numerous high performance/high functional materials such as superconductors. (NEDO)

Fast and precise luminosity measurement at the international linear ...

Indian Academy of Sciences (India)

6. — journal of. December 2007 physics pp. 1151–1157. Fast and precise luminosity measurement ... The fast investigation of the collision quality for intrabunch feedback and the ... consisting of the sensor, the absorber and an interconnection structure. 2. ... outer radius of BeamCal is increased to keep the angular overlap.

The Design and Implementation of a Novel Open Source Massive Deployment System

Directory of Open Access Journals (Sweden)

Steven J. H. Shiau

2018-06-01

Full Text Available The hypervisor and container are emerging cloud computing and fog computing technologies, which enable rapid system deployment. However, both of the technologies depend on the operating system (OS and applications that are installed on the host machines. System deployment is the activity to deliver and install OSs and applications onto computers. Such deployment activities are widely required in the infrastructure of cloud computing, fog computing, high-performance computing clusters, and classrooms of computer education. Albeit the concept of system deployment is not new, traditional solutions cannot support the rapid evolution of open source file systems. Furthermore, existing solutions cannot support the massive deployment of disks in a computer as well as the massive deployment in large-scale computers. To resolve the issue, the authors proposed novel system architecture as well as software that is openly available. The experiments are undertaken by deploying a Linux system to 1 to 30 Universal Serial Bus (USB flash drives in a single machine and to 1 to 32 machines in a network using the software that is being developed in this work. The results have demonstrated the feasibility and efficiency of the proposed work. The relationships between the bus bandwidth, the writing rate of the USB flash drive, and the number of flash drives were also formulated as a govern equation. Performance evaluation and cost savings in comparing to the deployment cases adopting commercial software were also provided for demonstrating the performance enhancement and cost reduction by using the novel deployment system. In general, the proposed architecture and the developed software are highly effective from the aspects of both performance and cost.

High-frequency field-deployable isotope analyzer for hydrological applications

Science.gov (United States)

Elena S.F. Berman; Manish Gupta; Chris Gabrielli; Tina Garland; Jeffrey J. McDonnell

2009-01-01

A high-frequency, field-deployable liquid water isotope analyzer was developed. The instrument was deployed for 4 contiguous weeks in the H. J. Andrews Experimental Forest Long-term Ecological Research site in western Oregon, where it was used for real-time measurement of the isotope ratios of precipitation and stream water during three large storm events. We were able...

ISIS Child Soldiers in Syria: The Structural and Predatory Recruitment, Enlistment, Pre-Training Indoctrination, Training, and Deployment

OpenAIRE

Asaad Almohammad

2018-01-01

Research on the engagement of children with the so-called Islamic State (a.k.a. ISIS) relies heavily on the analysis of obtained ISIS documents and ISIS-disseminated propaganda, leaving major elements of the recruitment and deployment process uncovered. Such ambiguities hinder future efforts aimed at dealing with ISIS’ child soldiers. As such, an intensive effort to compile data using interviews and naturalistic observations across ISIS-held territories in Syria was made to exhaustively explo...

When Loved Ones Get Deployed

Science.gov (United States)

... different from hearing about conflicts and violence that break out in the world during our own time. If someone you care about is in the military and is deployed for duty, it's natural to worry about their safety. That's especially true if the person is going ...

Automated Deployment of Advanced Controls and Analytics in Buildings

Science.gov (United States)

Pritoni, Marco

Buildings use 40% of primary energy in the US. Recent studies show that developing energy analytics and enhancing control strategies can significantly improve their energy performance. However, the deployment of advanced control software applications has been mostly limited to academic studies. Larger-scale implementations are prevented by the significant engineering time and customization required, due to significant differences among buildings. This study demonstrates how physics-inspired data-driven models can be used to develop portable analytics and control applications for buildings. Specifically, I demonstrate application of these models in all phases of the deployment of advanced controls and analytics in buildings: in the first phase, "Site Preparation and Interface with Legacy Systems" I used models to discover or map relationships among building components, automatically gathering metadata (information about data points) necessary to run the applications. During the second phase: "Application Deployment and Commissioning", models automatically learn system parameters, used for advanced controls and analytics. In the third phase: "Continuous Monitoring and Verification" I utilized models to automatically measure the energy performance of a building that has implemented advanced control strategies. In the conclusions, I discuss future challenges and suggest potential strategies for these innovative control systems to be widely deployed in the market. This dissertation provides useful new tools in terms of procedures, algorithms, and models to facilitate the automation of deployment of advanced controls and analytics and accelerate their wide adoption in buildings.

Deploying Missile Defense: Major Operational Challenges

National Research Council Canada - National Science Library

Bunn, M

2004-01-01

By October 2004, the United States will have begun initial deployment of a missile defense capability albeit a modest, limited, and not completely proven one to defend the homeland against a limited...

Deployment of field hospitals to disaster regions: Insights from ten medical relief operations spanning three decades.

Science.gov (United States)

Naor, Michael; Heyman, Samuel N; Bader, Tarif; Merin, Ofer

2017-01-01

The Israeli Defense Force (IDF) Medical Corps developed a model of airborne field hospital. This model was structured to deal with disaster settings, requiring self-sufficiency, innovation and flexible operative mode in the setup of large margins of uncertainty regarding the disaster environment. The current study is aimed to critically analyze the experience, gathered in ten such missions worldwide. Interviews with physicians who actively participated in the missions from 1988 until 2015 as chief medical officers combined with literature review of principal medical and auxiliary publications in order to assess and integrate information about the assembly of these missions. A body of knowledge was accumulated over the years by the IDF Medical Corps from deploying numerous relief missions to both natural (earthquake, typhoon, and tsunami), and man-made disasters, occurring in nine countries (Armenia, Rwanda, Kosovo, Turkey, India, Haiti, Japan, Philippines, and Nepal). This study shows an evolutionary pattern with improvements implemented from one mission to the other, with special adaptations (creativity and improvisation) to accommodate logistics barriers. The principals and operative function for deploying medical relief system, proposed over 20 years ago, were challenged and validated in the subsequent missions of IDF outlined in the current study. These principals, with the advantage of the military infrastructure and the expertise of drafted civilian medical professionals enable the rapid assembly and allocation of highly competent medical facilities in disaster settings. This structure model is to large extent self-sufficient with a substantial operative flexibility that permits early deployment upon request while the disaster assessment and definition of needs are preliminary.