Wireless energy transmission to supplement energy harvesters in sensor network applications

Energy Technology Data Exchange (ETDEWEB)

Farinholt, Kevin M [Los Alamos National Laboratory; Taylor, Stuart G [Los Alamos National Laboratory; Park, Gyuhae [Los Alamos National Laboratory; Farrar, Charles R [Los Alamos National Laboratory

2010-01-01

In this paper we present a method for coupling wireless energy transmission with traditional energy harvesting techniques in order to power sensor nodes for structural health monitoring applications. The goal of this study is to develop a system that can be permanently embedded within civil structures without the need for on-board power sources. Wireless energy transmission is included to supplement energy harvesting techniques that rely on ambient or environmental, energy sources. This approach combines several transducer types that harvest ambient energy with wireless transmission sources, providing a robust solution that does not rely on a single energy source. Experimental results from laboratory and field experiments are presented to address duty cycle limitations of conventional energy harvesting techniques, and the advantages gained by incorporating a wireless energy transmission subsystem. Methods of increasing the efficiency, energy storage medium, target applications and the integrated use of energy harvesting sources with wireless energy transmission will be discussed.

Phased Array Excitations For Efficient Near Field Wireless Power Transmission

Science.gov (United States)

2016-09-01

channeled to the battery or power plant. Figure 2. WPT System Block Diagram for Battery Charging. Source : [2]. Wireless power transfer has gained...EXCITATIONS FOR EFFICIENT NEAR-FIELD WIRELESS POWER TRANSMISSION by Sean X. Hong September 2016 Thesis Advisor: David Jenn Second Reader...TYPE AND DATES COVERED Master’s thesis 4. TITLE AND SUBTITLE PHASED ARRAY EXCITATIONS FOR EFFICIENT NEAR-FIELD WIRELESS POWER TRANSMISSION 5

Interference-Robust Transmission in Wireless Sensor Networks.

Science.gov (United States)

Han, Jin-Seok; Lee, Yong-Hwan

2016-11-14

Low-power wireless sensor networks (WSNs) operating in unlicensed spectrum bands may seriously suffer from interference from other coexisting radio systems, such as IEEE 802.11 wireless local area networks. In this paper, we consider the improvement of the transmission performance of low-power WSNs by adjusting the transmission rate and the payload size in response to the change of co-channel interference. We estimate the probability of transmission failure and the data throughput and then determine the payload size to maximize the throughput performance. We investigate that the transmission time maximizing the normalized throughput is not much affected by the transmission rate, but rather by the interference condition. We adjust the transmission rate and the transmission time in response to the change of the channel and interference condition, respectively. Finally, we verify the performance of the proposed scheme by computer simulation. The simulation results show that the proposed scheme significantly improves data throughput compared with conventional schemes while preserving energy efficiency even in the presence of interference.

Electrodynamic Wireless Power Transmission to Rotating Magnet Receivers

International Nuclear Information System (INIS)

Garraud, A; Jimenez, J D; Garraud, N; Arnold, D P

2014-01-01

This paper presents an approach for electrodynamic wireless power transmission (EWPT) using a synchronously rotating magnet located in a 3.2 cm 3 receiver. We demonstrate wireless power transmission up to 99 mW (power density equal to 31 mW/cm 3 ) over a 5-cm distance and 5 mW over a 20-cm distance. The maximum operational frequency, and hence maximal output power, is constrained by the magnetic field amplitude. A quadratic relationship is found between the maximal output power and the magnetic field. We also demonstrate simultaneous, power transmission to multiple receivers positioned at different locations

Priority image transmission in wireless sensor networks

International Nuclear Information System (INIS)

Nasri, M.; Helali, A.; Sghaier, H.; Maaref, H.

2011-01-01

The emerging technology during the last years allowed the development of new sensors equipped with wireless communication which can be organized into a cooperative autonomous network. Some application areas for wireless sensor networks (WSNs) are home automations, health care services, military domain, and environment monitoring. The required constraints are limited capacity of processing, limited storage capability, and especially these nodes are limited in energy. In addition, such networks are tiny battery powered which their lifetime is very limited. During image processing and transmission to the destination, the lifetime of sensor network is decreased quickly due to battery and processing power constraints. Therefore, digital image transmissions are a significant challenge for image sensor based Wireless Sensor Networks (WSNs). Based on a wavelet image compression, we propose a novel, robust and energy-efficient scheme, called Priority Image Transmission (PIT) in WSN by providing various priority levels during image transmissions. Different priorities in the compressed image are considered. The information for the significant wavelet coeffcients are transmitted with higher quality assurance, whereas relatively less important coefficients are transmitted with lower overhead. Simulation results show that the proposed scheme prolongs the system lifetime and achieves higher energy efficiency in WSN with an acceptable compromise on the image quality.

[Review of wireless energy transmission system for total artificial heart].

Science.gov (United States)

Zhang, Chi; Yang, Ming

2009-11-01

This paper sums up the fundamental structure of wireless energy transmission system for total artificial heart, and compares the key parameters and performance of some representative systems. After that, it is discussed that the future development trend of wireless energy transmission system for total artificial heart.

Communication protocol in chassis detecting wireless transmission system based on WiFi

Science.gov (United States)

In chassis detecting wireless transmission system, the wireless network communication protocol plays a key role in the information exchange and synchronization between the host and chassis PDA. This paper presents a wireless network transmission protocol based on TCP/IP which makes the rules of info...

Transmission Delay Based Control over Networks with Wireless Links

Institute of Scientific and Technical Information of China (English)

无

2002-01-01

To achieve the mobility of computers during communication, the TCP connections between fixed host and mobile host may often traverse wired and wireless networks, and the recovery of losses due to wireless transmission error is much different from congestion control. The paper analyzes the side effect of RTT estimation while making the TCP source to handle congestion and wireless error losses properly. Then present a strategy using information feedback by the last hop acknowledgement and monitoring the queuing level of the wired bottleneck link by calculating the changes in transmission delay along the path. With the identification of the early stage of congestion, it can respond to wired congestion quickly while keeping wireless link more reliable, and make TCP react to the different packets losses more appropriately.

Electrodynamic wireless power transmission to a torsional receiver

International Nuclear Information System (INIS)

McEachern, K M; Arnold, D P

2013-01-01

This paper presents a wireless power transmission (WPT) concept that uses electrodynamic coupling and torsional motion of a permanent magnet in the receiver. The system is shown to transfer an average power of 3.09 mW (power density equal to 143 μW/cm 3 ) over a distance of 1 cm, an average power of 1.98 mW over a distance of 2 cm, and an average power of 126 μW over a distance of 7 cm. We also demonstrate unaltered power transmission through conductive media, including a human hand and an aluminum plate, highlighting a key advantage of the electrodynamic wireless power transmission approach

60 Gbit/s 400 GHz Wireless Transmission

DEFF Research Database (Denmark)

Yu, Xianbin; Asif, Rameez; Piels, Molly

2015-01-01

We experimentally demonstrate a 400 GHz carrier wireless transmission system with real-time capable detection and demonstrate transmission of a 60 Gbit/s signal derived from optical Nyquist channels in a 12.5 GHz ultra-dense wavelength division multiplexing (UD-WDM) grid and carrying QPSK...

Characteristic of wireless power transmission S-Parameter for a superconductor coil

International Nuclear Information System (INIS)

Jeong, In Sung; Jung, Byung Ik; Choi, Hyo Sang

2015-01-01

Many studies are being conducted to implement wireless charging, for example, for cellular phones or electronic tooth brushes, via wireless power transmission technique. However, the magnetic induction method had a very short transmission distance. To solve this problem, the team of Professor Marin Soljacic proposed a magnetic resonance system that used two resonance coils with the same resonance frequency. It had an approximately 40% efficiency at a 2m distance. The system improved the low efficiency and short distance problems of the existing systems. So it could also widen the application range of wireless power transmission. Many studies on the subject are underway. In this paper, the superconductor coil was used to improve the efficiency of magnetic resonance wireless power transmission. The resonance wireless power transmission system had a source coil, a load coil, and resonance coils (a transmitter and a receiver). The efficiency and distance depended on the characteristics of the transmitter and receiver coils that had the same resonance frequency. Therefore, two resonance coils were fabricated by superconductors. The current density of the superconductor was higher than that of the normal conductor coil. Accordingly, it had a high quality-factor and improved efficiency

Characteristic of wireless power transmission S-Parameter for a superconductor coil

Energy Technology Data Exchange (ETDEWEB)

Jeong, In Sung; Jung, Byung Ik; Choi, Hyo Sang [Chosun University, Gwangju (Korea, Republic of)

2015-03-15

Many studies are being conducted to implement wireless charging, for example, for cellular phones or electronic tooth brushes, via wireless power transmission technique. However, the magnetic induction method had a very short transmission distance. To solve this problem, the team of Professor Marin Soljacic proposed a magnetic resonance system that used two resonance coils with the same resonance frequency. It had an approximately 40% efficiency at a 2m distance. The system improved the low efficiency and short distance problems of the existing systems. So it could also widen the application range of wireless power transmission. Many studies on the subject are underway. In this paper, the superconductor coil was used to improve the efficiency of magnetic resonance wireless power transmission. The resonance wireless power transmission system had a source coil, a load coil, and resonance coils (a transmitter and a receiver). The efficiency and distance depended on the characteristics of the transmitter and receiver coils that had the same resonance frequency. Therefore, two resonance coils were fabricated by superconductors. The current density of the superconductor was higher than that of the normal conductor coil. Accordingly, it had a high quality-factor and improved efficiency.

Low-complexity JPEG-based progressive video codec for wireless video transmission

DEFF Research Database (Denmark)

Ukhanova, Ann; Forchhammer, Søren

2010-01-01

This paper discusses the question of video codec enhancement for wireless video transmission of high definition video data taking into account constraints on memory and complexity. Starting from parameter adjustment for JPEG2000 compression algorithm used for wireless transmission and achieving...

Design and implementation on wireless transmission platform of area radiation monitoring data

International Nuclear Information System (INIS)

Li Dan; Ge Liangquan; Lai Wanchang; Ren Yong; Liu Huijun; Wang Guangxi

2011-01-01

To solve data transmission problems of radiation area monitoring system, Wireless transmission platform is built based on ZigBee module, thus wireless transmission between the radiation area central node and the monitoring points is achieved. It introduces the framework of ZigBee protocol, APL applications between FFD and RFD module, FFD, module and central node host, and RFD module and monitoring equipment, are developed using simplified protocol stack. Wireless network is set up using a FFD module and two RFD modules, the results show that RSSI are above 50, and the data communication is normal for the transmission distance of 60 m. (authors)

A study on the wireless transmission characteristic in the deep underground

International Nuclear Information System (INIS)

Takamura, Hisashi; Okutsu, Kazuo; Sugahara, Norihisa; Torata, Shinichiro; Ohuchi, Jin

2006-01-01

A wireless transmission technology uses a low frequency electromagnetic wave (100[Hz] - 10[kHz]) as a carrier wave to transmit signals in the deep underground geological condition. However, this electromagnetic wave has not been used so much, because the transmission capacity is less than a high frequency electromagnetic wave, which is used to televisions and cellular phones. On the other hand, the wireless transmission technology that doesn't use the cable is considered to be useful in the radioactive waste disposal repository from the viewpoint of decreasing the influence on the barrier. This paper shows the characteristics of the wireless transmission in the granite on the basis of the in situ testing implemented in the Aespoe Hard Rock Laboratory of SKB. (author)

Feasibility study of wireless power transmission systems

Science.gov (United States)

Robinson, W. J., Jr.

1968-01-01

Wireless microwave or laser energy transfers power from a manned earth-orbiting central station to unmanned astronomical substations. More efficient systems are required for the microwave power transmission.

Wireless Communications for Monitoring Nuclear Material Processes Part 2: Wireless In-plant Data Transmission

International Nuclear Information System (INIS)

Braina, F.; Goncalves, J.M.C.; Versino, C.; Heppleston, M.; Ottesen, C.; Schoeneman, B.; Tolk, K.

2008-01-01

The wireless transmission of data from sensors, monitoring both static and dynamic safeguards processes, is highly appealing for the simple fact that there are no wires. In a nuclear safeguards regime, this has the implied benefits of low-cost installations, versatile configurations, and the elimination of conduits to inspect. However, with the implied solutions of wireless, we are presented with a new set of problems for system implementation and operation management, in particular (1) Radio Frequency (RF) interference and (2) security in information transmission. These problems are addressable. This paper looks at the clear benefits of wireless technologies and the cautions regarding the possible pitfalls of poorly applied technology, discusses the integration of radio frequency in existing and new facilities, provides high-level considerations for information security, and reviews prospects for the future

How does wireless phones effect communication and treatment in hospitals?

DEFF Research Database (Denmark)

Paasch, Bettina Sletten

The use of wireless phones in hospital units are increasing, inducing practitioners to carry a working phone each. A study performed in a medical hospital unit demonstrates that wireless phones can impair communication between health care practitioners and patients (Paasch, in press). Also wireless...... phones can compromise patient safety, both by disturbing the practitioners’ concentration, causing mistakes, and by transporting bacteria between patients. This qualitative Ph.D.-study wishes to further investigate the effect of wireless phones on communication and treatment in hospital units, using...... participant observations, ethnographic interviews and video observations. The study will explore how wireless phones mediate and is mediated by practitioners communication with each other and patients. As hospitals are constructed and reconstructed by all communication within, this insight will enable...

Resource-Constrained Low-Complexity Video Coding for Wireless Transmission

DEFF Research Database (Denmark)

Ukhanova, Ann

of video quality. We proposed a new metric for objective quality assessment that considers frame rate. As many applications deal with wireless video transmission, we performed an analysis of compression and transmission systems with a focus on power-distortion trade-off. We proposed an approach...... for ratedistortion-complexity optimization of upcoming video compression standard HEVC. We also provided a new method allowing decrease of power consumption on mobile devices in 3G networks. Finally, we proposed low-delay and low-power approaches for video transmission over wireless personal area networks, including......Constrained resources like memory, power, bandwidth and delay requirements in many mobile systems pose limitations for video applications. Standard approaches for video compression and transmission do not always satisfy system requirements. In this thesis we have shown that it is possible to modify...

Mutual trust method for forwarding information in wireless sensor networks using random secret pre-distribution

Directory of Open Access Journals (Sweden)

Chih-Hsueh Lin

2016-04-01

Full Text Available In wireless sensor networks, sensing information must be transmitted from sensor nodes to the base station by multiple hopping. Every sensor node is a sender and a relay node that forwards the sensing information that is sent by other nodes. Under an attack, the sensing information may be intercepted, modified, interrupted, or fabricated during transmission. Accordingly, the development of mutual trust to enable a secure path to be established for forwarding information is an important issue. Random key pre-distribution has been proposed to establish mutual trust among sensor nodes. This article modifies the random key pre-distribution to a random secret pre-distribution and incorporates identity-based cryptography to establish an effective method of establishing mutual trust for a wireless sensor network. In the proposed method, base station assigns an identity and embeds n secrets into the private secret keys for every sensor node. Based on the identity and private secret keys, the mutual trust method is utilized to explore the types of trust among neighboring sensor nodes. The novel method can resist malicious attacks and satisfy the requirements of wireless sensor network, which are resistance to compromising attacks, masquerading attacks, forger attacks, replying attacks, authentication of forwarding messages, and security of sensing information.

Study on frequency characteristics of wireless power transmission system based on magnetic coupling resonance

Science.gov (United States)

Liang, L. H.; Liu, Z. Z.; Hou, Y. J.; Zeng, H.; Yue, Z. K.; Cui, S.

2017-11-01

In order to study the frequency characteristics of the wireless energy transmission system based on the magnetic coupling resonance, a circuit model based on the magnetic coupling resonant wireless energy transmission system is established. The influence of the load on the frequency characteristics of the wireless power transmission system is analysed. The circuit coupling theory is used to derive the minimum load required to suppress frequency splitting. Simulation and experimental results verify that when the load size is lower than a certain value, the system will appear frequency splitting, increasing the load size can effectively suppress the frequency splitting phenomenon. The power regulation scheme of the wireless charging system based on magnetic coupling resonance is given. This study provides a theoretical basis for load selection and power regulation of wireless power transmission systems.

Coordinated Transmissions to Direct and Relayed Users in Wireless Cellular Systems

DEFF Research Database (Denmark)

Thai, Chan; Popovski, Petar; Kaneko, Megumi

2011-01-01

The ideas of wireless network coding at the physical layer promise high throughput gains in wireless systems with relays and multi–way traffic flows. This gain can be ascribed to two principles: (1) joint transmission of multiple communication flows and (2) usage of a priori information to cancel...... the interference. In this paper we use these principles to devise new transmission schemes in wireless cellular systems that feature both users served directly by the base stations (direct users) and users served through relays (relayed users). We present four different schemes for coordinated transmission...... of uplink and downlink traffic in which one direct and one relayed user are served. These schemes are then used as building blocks in multi–user scenarios, where we present several schemes for scheduling pairs of users for coordinated transmissions. The optimal scheme involves exhaustive search of the best...

Wireless data transmission from inside electromagnetic fields.

Science.gov (United States)

Huertas, José Ignacio; Barraza, Roberto; Echeverry, Julian Mauricio

2010-01-01

This paper describes analytical and experimental work developed to evaluate the effects of the electromagnetic fields produced by high-voltage lines (400 kV) on wireless data transmission at the 900MHz band. In this work the source of the data transmission is located inside the electromagnetic field and the reception station is located at different distances from the power lines. Different atmospheric conditions are considered.

Interference Cancellation for Coexisting Wireless Data and Power Transmission in the Same Frequency

International Nuclear Information System (INIS)

Yamazaki, Keita; Sugiyama, Yusuke; Saruwatari, Shunsuke; Kawahara, Yoshihiro; Watanabe, Takashi

2014-01-01

Combining wireless transmission of data and power signals enables wireless sensor networks to drive perpetually without changing batteries. To achieve the simultaneous data and power transmission, the present paper proposes power signal interference cancellation for wireless data and power transmission at the same time in the same frequency. We evaluate the performance of the proposed power signal interference cancellation using Universal Software Radio Peripheral N200 (USRP N200) software defined radio. Evaluations show that the proposed interference cancellation is feasible to receive data while transmitting power

4 Gbps Impulse Radio (IR) Ultra-Wideband (UWB) Transmission over 100 Meters Multi Mode Fiber with 4 Meters Wireless Transmission

DEFF Research Database (Denmark)

Jensen, Jesper Bevensee; Rodes Lopez, Roberto; Caballero Jambrina, Antonio

2009-01-01

We present experimental demonstrations of in-building impulse radio (IR) ultra-wideband (UWB) link consisting of 100 m multi mode fiber (MMF) and 4 m wireless transmission at a record 4 Gbps, and a record 8 m wireless transmission at 2.5 Gbps. A directly modulated vertical cavity surface emitting...... laser (VCSEL) was used for the generation of the optical signal. 8 m at 2.5 Gbps corresponds to a bit rate - distance product of 20; the highest yet reported for wireless IR-UWB transmission...

Multi-carrier transmission for hybrid radio frequency with optical wireless communications

Science.gov (United States)

Wang, Gang; Chen, Genshe; Shen, Dan; Pham, Khanh; Blasch, Erik; Nguyen, Tien M.

2015-05-01

Radio frequency (RF) wireless communication is reaching its capacity to support large data rate transmissions due to hardware constraints (e.g., silicon processes), software strategies (e.g., information theory), and consumer desire for timely large file exchanges (e.g., big data and mobile cloud computing). A high transmission rate performance must keep pace with the generated huge volumes of data for real-time processing. Integrated RF and optical wireless communications (RF/OWC) could be the next generation transmission technology to satisfy both the increased data rate exchange and the communications constraints. However, with the promising benefits of RF/OWC, challenges remain to fully develop hybrid RF with wireless optical communications such as uniform waveform design for information transmission and detection. In this paper, an orthogonal frequency division multiplexing (OFDM) transmission scheme, which widely employed in RF communications, is developed for optical communications. The traditional high peak-to-average power ratio (PAPR) in OFDM is reduced to improve system performance. The proposed multi-carrier waveform is evaluated with a frequency-selective fading channel. The results demonstrate that bit error rate (BER) performance of our proposed optical OFDM transmission technique outperforms the traditional OWC on-off keying (OOK) transmission scheme.

Analysis of mobile fronthaul bandwidth and wireless transmission performance in split-PHY processing architecture.

Science.gov (United States)

Miyamoto, Kenji; Kuwano, Shigeru; Terada, Jun; Otaka, Akihiro

2016-01-25

We analyze the mobile fronthaul (MFH) bandwidth and the wireless transmission performance in the split-PHY processing (SPP) architecture, which redefines the functional split of centralized/cloud RAN (C-RAN) while preserving high wireless coordinated multi-point (CoMP) transmission/reception performance. The SPP architecture splits the base stations (BS) functions between wireless channel coding/decoding and wireless modulation/demodulation, and employs its own CoMP joint transmission and reception schemes. Simulation results show that the SPP architecture reduces the MFH bandwidth by up to 97% from conventional C-RAN while matching the wireless bit error rate (BER) performance of conventional C-RAN in uplink joint reception with only 2-dB signal to noise ratio (SNR) penalty.

[Design and optimization of wireless power and data transmission for visual prosthesis].

Science.gov (United States)

Lei, Xuping; Wu, Kaijie; Zhao, Lei; Chai, Xinyu

2013-11-01

Boosting spatial resolution of visual prostheses is an effective method to improve implant subjects' visual perception. However, power consumption of visual implants greatly rises with the increasing number of implanted electrodes. In respond to this trend, visual prostheses need to develop high-efficiency wireless power transmission and high-speed data transmission. This paper presents a review of current research progress on wireless power and data transmission for visual prostheses, analyzes relative principles and requirement, and introduces design methods of power and data transmission.

The optimization of wireless power transmission: design and realization.

Science.gov (United States)

Jia, Zhiwei; Yan, Guozheng; Liu, Hua; Wang, Zhiwu; Jiang, Pingping; Shi, Yu

2012-09-01

A wireless power transmission system is regarded as a practical way of solving power-shortage problems in multifunctional active capsule endoscopes. The uniformity of magnetic flux density, frequency stability and orientation stability are used to evaluate power transmission stability, taking into consideration size and safety constraints. Magnetic field safety and temperature rise are also considered. Test benches are designed to measure the relevent parameters. Finally, a mathematical programming model in which these constraints are considered is proposed to improve transmission efficiency. To verify the feasibility of the proposed method, various systems for a wireless active capsule endoscope are designed and evaluated. The optimal power transmission system has the capability to supply continuously at least 500 mW of power with a transmission efficiency of 4.08%. The example validates the feasibility of the proposed method. Introduction of novel designs enables further improvement of this method. Copyright © 2012 John Wiley & Sons, Ltd.

Transmission Power Control for Wireless Sensor Network

Directory of Open Access Journals (Sweden)

Kuo-Hsien Hsia

2017-02-01

Full Text Available Wireless sensor networks can be widely applied for a security system or a smart home system. Since some of the wireless remote sensor nodes may be powered by energy storage devices such as batteries, it is a very important issue to transmit signals at lower power with the consideration of the communication effectiveness. In this paper, we will provide a fuzzy controller with two inputs and one output for received signal strength indicator (RSSI and link quality indicator (LQI to adjust transmission power suitably in order to maintaining a certain communication level with a reduced energy consumption. And we will divide the sampling period of a sensor node into four intervals so that the sensor node radio device does not in receiving or transmission status all the time. Hence the sensor node can adjust transmission power automatically and reduce sensor node power consumption. Experimental results show that the battery life can be extended to about 10 times for the designed sensor node comparing to a normal node.

Portable wireless power transmission system for video capsule endoscopy.

Science.gov (United States)

Zhiwei, Jia; Guozheng, Yan; Bingquan, Zhu

2014-10-01

Wireless power transmission is considered a practical way of overcoming the power shortage of wireless capsule endoscopy (VCE). However, most patients cannot tolerate the long hours of lying in a fixed transmitting coil during diagnosis. To develop a portable wireless power transmission system for VCE, a compact transmitting coil and a portable inverter circuit driven by rechargeable batteries are proposed. The couple coils, optimized considering the stability and safety conditions, are 28 turns of transmitting coil and six strands of receiving coil. The driven circuit is designed according to the portable principle. Experiments show that the integrated system could continuously supply power to a dual-head VCE for more than 8 h at a frame rate of 30 frames per second with resolution of 320 × 240. The portable VCE exhibits potential for clinical applications, but requires further improvement and tests.

Wireless OAM transmission system based on elliptical microstrip patch antenna.

Science.gov (United States)

Chen, Jia Jia; Lu, Qian Nan; Dong, Fei Fei; Yang, Jing Jing; Huang, Ming

2016-05-30

The multiplexing transmission has always been a focus of attention for communication technology. In this paper, the radiation characteristics of circular microstrip patch antenna was firstly analyzed based on cavity model theory, and then spiral beams carrying orbital angular momentum (OAM) were generated, using elliptical microstrip patch antenna, with a single feed probe instead of a standard circular patch with two feedpoints. Moreover, by combining the proposed elliptic microstrip patch antenna with Universal Software Radio Peripheral (USRP), a wireless OAM transmission system was established and the real-time transmission of text, image and video in a real channel environment was realized. Since the wireless OAM transmission has the advantage of good safety and high spectrum utilization efficiency, this work has theoretical significance and potential application.

40-Gb/s PDM-QPSK signal transmission over 160-m wireless distance at W-band.

Science.gov (United States)

Xiao, Jiangnan; Yu, Jianjun; Li, Xinying; Xu, Yuming; Zhang, Ziran; Chen, Long

2015-03-15

We experimentally demonstrate a W-band optical-wireless transmission system over 160-m wireless distance with a bit rate up to 40 Gb/s. The optical-wireless transmission system adopts optical polarization-division-multiplexing (PDM), multiple-input multiple-output (MIMO) reception and antenna polarization diversity. Using this system, we experimentally demonstrate the 2×2 MIMO wireless delivery of 20- and 40-Gb/s PDM quadrature-phase-shift-keying (PDM-QPSK) signals over 640- and 160-m wireless links, respectively. The bit-error ratios (BERs) of these transmission systems are both less than the forward-error-correction (FEC) threshold of 3.8×10-3.

Prediction of transmission distortion for wireless video communication: analysis.

Science.gov (United States)

Chen, Zhifeng; Wu, Dapeng

2012-03-01

Transmitting video over wireless is a challenging problem since video may be seriously distorted due to packet errors caused by wireless channels. The capability of predicting transmission distortion (i.e., video distortion caused by packet errors) can assist in designing video encoding and transmission schemes that achieve maximum video quality or minimum end-to-end video distortion. This paper is aimed at deriving formulas for predicting transmission distortion. The contribution of this paper is twofold. First, we identify the governing law that describes how the transmission distortion process evolves over time and analytically derive the transmission distortion formula as a closed-form function of video frame statistics, channel error statistics, and system parameters. Second, we identify, for the first time, two important properties of transmission distortion. The first property is that the clipping noise, which is produced by nonlinear clipping, causes decay of propagated error. The second property is that the correlation between motion-vector concealment error and propagated error is negative and has dominant impact on transmission distortion, compared with other correlations. Due to these two properties and elegant error/distortion decomposition, our formula provides not only more accurate prediction but also lower complexity than the existing methods.

The Design of Wireless Data Acquisition and Remote Transmission Interface in Micro-seismic Signals

Directory of Open Access Journals (Sweden)

Huan-Huan BIAN

2014-02-01

Full Text Available The micro-seismic signal acquisition and transmission is an important key part in geological prospecting. This paper describes a bran-new solution of micro-seismic signal acquisition and remote transmission using Zigbee technique and wireless data transmission technique. The hardware such as front-end data acquisition interface made up by Zigbee wireless networking technique, remote data transmission solution composed of general packet radio service (or GPRS for short technique and interface between Zigbee and GPRS is designed in detail. Meanwhile the corresponding software of the system is given out. The solution solves the numerous practical problems nagged by complex and terrible environment faced using micro-seismic prospecting. The experimental results demonstrate that the method using Zigbee wireless network communication technique GPRS wireless packet switching technique is efficient, reliable and flexible.

A Beacon Transmission Power Control Algorithm Based on Wireless Channel Load Forecasting in VANETs.

Science.gov (United States)

Mo, Yuanfu; Yu, Dexin; Song, Jun; Zheng, Kun; Guo, Yajuan

2015-01-01

In a vehicular ad hoc network (VANET), the periodic exchange of single-hop status information broadcasts (beacon frames) produces channel loading, which causes channel congestion and induces information conflict problems. To guarantee fairness in beacon transmissions from each node and maximum network connectivity, adjustment of the beacon transmission power is an effective method for reducing and preventing channel congestion. In this study, the primary factors that influence wireless channel loading are selected to construct the KF-BCLF, which is a channel load forecasting algorithm based on a recursive Kalman filter and employs multiple regression equation. By pre-adjusting the transmission power based on the forecasted channel load, the channel load was kept within a predefined range; therefore, channel congestion was prevented. Based on this method, the CLF-BTPC, which is a transmission power control algorithm, is proposed. To verify KF-BCLF algorithm, a traffic survey method that involved the collection of floating car data along a major traffic road in Changchun City is employed. By comparing this forecast with the measured channel loads, the proposed KF-BCLF algorithm was proven to be effective. In addition, the CLF-BTPC algorithm is verified by simulating a section of eight-lane highway and a signal-controlled urban intersection. The results of the two verification process indicate that this distributed CLF-BTPC algorithm can effectively control channel load, prevent channel congestion, and enhance the stability and robustness of wireless beacon transmission in a vehicular network.

A Beacon Transmission Power Control Algorithm Based on Wireless Channel Load Forecasting in VANETs.

Directory of Open Access Journals (Sweden)

Yuanfu Mo

Full Text Available In a vehicular ad hoc network (VANET, the periodic exchange of single-hop status information broadcasts (beacon frames produces channel loading, which causes channel congestion and induces information conflict problems. To guarantee fairness in beacon transmissions from each node and maximum network connectivity, adjustment of the beacon transmission power is an effective method for reducing and preventing channel congestion. In this study, the primary factors that influence wireless channel loading are selected to construct the KF-BCLF, which is a channel load forecasting algorithm based on a recursive Kalman filter and employs multiple regression equation. By pre-adjusting the transmission power based on the forecasted channel load, the channel load was kept within a predefined range; therefore, channel congestion was prevented. Based on this method, the CLF-BTPC, which is a transmission power control algorithm, is proposed. To verify KF-BCLF algorithm, a traffic survey method that involved the collection of floating car data along a major traffic road in Changchun City is employed. By comparing this forecast with the measured channel loads, the proposed KF-BCLF algorithm was proven to be effective. In addition, the CLF-BTPC algorithm is verified by simulating a section of eight-lane highway and a signal-controlled urban intersection. The results of the two verification process indicate that this distributed CLF-BTPC algorithm can effectively control channel load, prevent channel congestion, and enhance the stability and robustness of wireless beacon transmission in a vehicular network.

Wireless transmission of power

International Nuclear Information System (INIS)

Grotz, T.

1991-01-01

This paper reports that it has been proven by researchers that electrical energy can be propagated around the world between the surface of the Earth and the ionosphere at extremely low frequencies in what is known as the Schumann Cavity. Experiments to data have shown that electromagnetic waves with frequencies in the range of 8 Hz, the fundamental Schumann Resonance frequency, propagate with litter attenuation around the planet within the Schumann Cavity. It is the intent of this research to determine if the Schumann Cavity can be resonated, if the power that is delivered to the cavity propagated with very low losses, and if power can be extracted at other locations within the cavity. Experimental data collected and calculations made in recent years support the hypothesis that wireless power transmission is a viable and practical alternative to the present systems of power transmission

Statistical performance evaluation of ECG transmission using wireless networks.

Science.gov (United States)

Shakhatreh, Walid; Gharaibeh, Khaled; Al-Zaben, Awad

2013-07-01

This paper presents simulation of the transmission of biomedical signals (using ECG signal as an example) over wireless networks. Investigation of the effect of channel impairments including SNR, pathloss exponent, path delay and network impairments such as packet loss probability; on the diagnosability of the received ECG signal are presented. The ECG signal is transmitted through a wireless network system composed of two communication protocols; an 802.15.4- ZigBee protocol and an 802.11b protocol. The performance of the transmission is evaluated using higher order statistics parameters such as kurtosis and Negative Entropy in addition to the common techniques such as the PRD, RMS and Cross Correlation.

Induction of Inflammation In Vivo by Electrocardiogram Sensor Operation Using Wireless Power Transmission.

Science.gov (United States)

Heo, Jin-Chul; Kim, Beomjoon; Kim, Yoon-Nyun; Kim, Dae-Kwang; Lee, Jong-Ha

2017-12-14

Prolonged monitoring by cardiac electrocardiogram (ECG) sensors is useful for patients with emergency heart conditions. However, implant monitoring systems are limited by lack of tissue biocompatibility. Here, we developed an implantable ECG sensor for real-time monitoring of ventricular fibrillation and evaluated its biocompatibility using an animal model. The implantable sensor comprised transplant sensors with two electrodes, a wireless power transmission system, and a monitoring system. The sensor was inserted into the subcutaneous tissue of the abdominal area and operated for 1 h/day for 5 days using a wireless power system. Importantly, the sensor was encapsulated by subcutaneous tissue and induced angiogenesis, inflammation, and phagocytosis. In addition, we observed that the levels of inflammation-related markers increased with wireless-powered transmission via the ECG sensor; in particular, levels of the Th-1 cytokine interleukin-12 were significantly increased. The results showed that induced tissue damage was associated with the use of wireless-powered sensors. We also investigated research strategies for the prevention of adverse effects caused by lack of tissue biocompatibility of a wireless-powered ECG monitoring system and provided information on the clinical applications of inflammatory reactions in implant treatment using the wireless-powered transmission system.

Pre-Hospital ECG E-Transmission for Patients with Suspected Myocardial Infarction in the Highlands of Scotland

Directory of Open Access Journals (Sweden)

Gordon F. Rushworth

2014-02-01

Full Text Available Patients with ST elevation myocardial infarction (STEMI require prompt treatment, best done by primary percutaneous coronary intervention (PPCI. However, for patients unable to receive PPCI, immediate pre-hospital thrombolysis (PHT is the best alternative. Evidence indicates that diagnostic and management support for staff increases the use of PHT. This study aimed to describe the patient demographics and management of patients, to determine any potential inter-area differences in referral rates to the ECG e-transmission service and to explore the views and experiences of key staff involved in ECG e-transmission within NHS Highland. Data from 2,025 patient episodes of ECG e-transmission identified a statistically significant geographical variation in ECG e-transmission and PHT delivery. Scottish Ambulance Service (SAS staff were more likely than GPs to deliver PHT overall, however, GPs were more likely to deliver in remote areas. Interviews with six Cardiac Care Unit (CCU nurses and six SAS staff highlighted their positive views of ECG e-transmission, citing perceived benefits to patients and interprofessional relationships. Poor access to network signal was noted to be a barrier to engaging in the system. This study has demonstrated that a specialist triage service based on e-transmission of ECGs in patients with suspected STEMI can be implemented in a diverse geographical setting. Work is needed to ensure equity of the service for all patients.

Coordinated Direct and Relay Transmission with Interference Cancelation in Wireless Systems

DEFF Research Database (Denmark)

Thai, Chan; Popovski, Petar

2011-01-01

Two-way relaying schemes in wireless systems obtain throughput gain by utilizing two features (1) jointly serve two communication flows, thus implementing network coding and (2) use of information that is a priori known to cancel interference and obtain the desired signal. Based on these principles......, we propose other schemes that bring throughput gains in wireless cellular systems, where relayed and direct transmissions are carried out in coordinated way. The results show that the coordinated transmission exhibit throughput improvement similar to the two–way relaying schemes....

Assessment of proactive transmission power control for wireless sensor networks

NARCIS (Netherlands)

kotian, Roshan; Exarchakos, Georgios; Liotta, Antonio

2014-01-01

In order to prolong lifetime of Wireless Sensor Networks (WSN), Transmission Power Control (TPC) techniques are employed. The existing TPC schemes adjust the transmission power mostly reacting to changes at link quality between communicating nodes. Proactive TPC has been proposed in the recent past

Wireless power transmission for battery charging

Science.gov (United States)

Mi, Chris; Li, Siqi; Nguyen, Trong-Duy; Wang, Junhua; Li, Jiangui; Li, Weihan; Xu, Jun

2016-11-15

A wireless power transmission system is provided for high power applications. The power transmission system is comprised generally of a charging unit configured to generate an alternating electromagnetic field and a receive unit configured to receive the alternating electromagnetic field from the charging unit. The charging unit includes a power source; an input rectifier; an inverter; and a transmit coil. The transmit coil has a spirangle arrangement segmented into n coil segments with capacitors interconnecting adjacent coil segments. The receive unit includes a receive coil and an output rectifier. The receive coil also has a spirangle arrangement segmented into m coil segments with capacitors interconnecting adjacent coil segments.

Induction of Inflammation In Vivo by Electrocardiogram Sensor Operation Using Wireless Power Transmission

Directory of Open Access Journals (Sweden)

Jin-Chul Heo

2017-12-01

Full Text Available Prolonged monitoring by cardiac electrocardiogram (ECG sensors is useful for patients with emergency heart conditions. However, implant monitoring systems are limited by lack of tissue biocompatibility. Here, we developed an implantable ECG sensor for real-time monitoring of ventricular fibrillation and evaluated its biocompatibility using an animal model. The implantable sensor comprised transplant sensors with two electrodes, a wireless power transmission system, and a monitoring system. The sensor was inserted into the subcutaneous tissue of the abdominal area and operated for 1 h/day for 5 days using a wireless power system. Importantly, the sensor was encapsulated by subcutaneous tissue and induced angiogenesis, inflammation, and phagocytosis. In addition, we observed that the levels of inflammation-related markers increased with wireless-powered transmission via the ECG sensor; in particular, levels of the Th-1 cytokine interleukin-12 were significantly increased. The results showed that induced tissue damage was associated with the use of wireless-powered sensors. We also investigated research strategies for the prevention of adverse effects caused by lack of tissue biocompatibility of a wireless-powered ECG monitoring system and provided information on the clinical applications of inflammatory reactions in implant treatment using the wireless-powered transmission system.

Simultaneous transmission of wired and wireless signals based on double sideband carrier suppression

Science.gov (United States)

Bitew, Mekuanint Agegnehu; Shiu, Run-Kai; Peng, Peng-Chun; Wang, Cheng-Hao; Chen, Yan-Ming

2017-11-01

In this paper, we proposed and experimentally demonstrated simultaneous transmission of wired and wireless signals based on double sideband optical carrier suppression. By properly adjusting the bias point of the dual-output mach-zehnder modulator (MZM), a central carrier in one output port and a pair of first-order sidebands in another output port are generated. The pair of first-order sidebands are fed into a second MZM to generate second-order order sidebands. A wired signal is embedded on the central carrier while a wireless signal is embedded on the second-order sidebands. Unlike other schemes, we did not use optical filter to separate the carrier from the optical sidebands. The measured bit error rate (BER) and eye-diagrams after a 25 km single-mode-fiber (SMF) transmission proved that the proposed scheme is successful for both wired and wireless signals transmission. Moreover, the power penalty at the BER of 10-9 is 0.3 and 0.7 dB for wired and wireless signals, respectively.

A wireless power transmission system for an active capsule endoscope for colon inspection.

Science.gov (United States)

Jia, Zhiwei; Yan, Guozheng; Shi, Yu; Zhu, Bingquan

2012-07-01

Multipurpose active capsule endoscopes (ACE) have drawn considerable attention in recent years, but these devices continue to suffer from energy limitations. In order to deliver stable and sufficient energy safely, a wireless power transmission system based on inductive coupling is presented. The system consists of a double-layer solenoid pair primary coil outside and a multiple secondary coils inside the body. At least 500 mW usable power can be transmitted under the worst geometrical conditions and the safety restraints in a volume of Φ13 × 13 mm. The wireless power transmission system is integrated to an ACE and applied in animal experiments. The designed wireless power transmission is proved to be feasible and potentially safe in a future application.

QoE-based transmission strategies for multi-user wireless information and power transfer

Directory of Open Access Journals (Sweden)

Taehun Jung

2015-12-01

Full Text Available One solution to the problem of supplying energy to wireless networks is wireless power transfer. One such technology–electromagnetic radiation enabled wireless power transfer–will change traditional wireless networks. In this paper, we investigate a transmission strategy for multi-user wireless information and power transfer. We consider a multi-user multiple-input multiple-output (MIMO channel that includes one base station (BS and two user terminals (UT consisting of one energy harvesting (EH receiver and one information decoding (ID receiver. Our system provides transmission strategies that can be executed and implemented in practical scenarios. The paper then analyzes the rate–energy (R–E pair of our strategies and compares them to those of the theoretical optimal strategy. We furthermore propose a QoE-based mode selection algorithm by mapping the R–E pair to the utility functions.

Ensuring the security and availability of a hospital wireless LAN system.

Science.gov (United States)

Hanada, Eisuke; Kudou, Takato; Tsumoto, Shusaku

2013-01-01

Wireless technologies as part of the data communication infrastructure of modern hospitals are being rapidly introduced. Even though there are concerns about problems associated with wireless communication security, the demand is remarkably large. Herein we discuss security countermeasures that must be taken and issues concerning availability that must be considered to ensure safe hospital/business use of wireless LAN systems, referring to the procedures introduced at a university hospital. Security countermeasures differ according to their purpose, such as preventing illegal use or ensuring availability, both of which are discussed. The main focus of the availability discussion is on signal reach, electromagnetic noise elimination, and maintaining power supply to the network apparatus. It is our hope that this information will assist others in their efforts to ensure safe implementation of wireless LAN systems, especially in hospitals where they have the potential to greatly improve information sharing and patient safety.

Bidirectional fiber-wireless and fiber-VLLC transmission system based on an OEO-based BLS and a RSOA.

Science.gov (United States)

Lu, Hai-Han; Li, Chung-Yi; Lu, Ting-Chien; Wu, Chang-Jen; Chu, Chien-An; Shiva, Ajay; Mochii, Takao

2016-02-01

A bidirectional fiber-wireless and fiber-visible-laser-light-communication (VLLC) transmission system based on an optoelectronic oscillator (OEO)-based broadband light source (BLS) and a reflective semiconductor optical amplifier (RSOA) is proposed and experimentally demonstrated. Through an in-depth observation of such bidirectional fiber-wireless and fiber-VLLC transmission systems, good bit error rate performances are obtained over a 40 km single-mode fiber and a 10 m RF/optical wireless transport. Such a bidirectional fiber-wireless and fiber-VLLC transmission system is an attractive option for providing broadband integrated services.

A reliable transmission protocol for ZigBee-based wireless patient monitoring.

Science.gov (United States)

Chen, Shyr-Kuen; Kao, Tsair; Chan, Chia-Tai; Huang, Chih-Ning; Chiang, Chih-Yen; Lai, Chin-Yu; Tung, Tse-Hua; Wang, Pi-Chung

2012-01-01

Patient monitoring systems are gaining their importance as the fast-growing global elderly population increases demands for caretaking. These systems use wireless technologies to transmit vital signs for medical evaluation. In a multihop ZigBee network, the existing systems usually use broadcast or multicast schemes to increase the reliability of signals transmission; however, both the schemes lead to significantly higher network traffic and end-to-end transmission delay. In this paper, we present a reliable transmission protocol based on anycast routing for wireless patient monitoring. Our scheme automatically selects the closest data receiver in an anycast group as a destination to reduce the transmission latency as well as the control overhead. The new protocol also shortens the latency of path recovery by initiating route recovery from the intermediate routers of the original path. On the basis of a reliable transmission scheme, we implement a ZigBee device for fall monitoring, which integrates fall detection, indoor positioning, and ECG monitoring. When the triaxial accelerometer of the device detects a fall, the current position of the patient is transmitted to an emergency center through a ZigBee network. In order to clarify the situation of the fallen patient, 4-s ECG signals are also transmitted. Our transmission scheme ensures the successful transmission of these critical messages. The experimental results show that our scheme is fast and reliable. We also demonstrate that our devices can seamlessly integrate with the next generation technology of wireless wide area network, worldwide interoperability for microwave access, to achieve real-time patient monitoring.

Hybrid wireless-over-fiber transmission system based on multiple injection-locked FP LDs.

Science.gov (United States)

Li, Chung-Yi; Lu, Hai-Han; Chu, Chien-An; Ying, Cheng-Ling; Lu, Ting-Chien; Peng, Peng-Chun

2015-07-27

A hybrid wireless-over-fiber (WoF) transmission system based on multiple injection-locked Fabry-Perot laser diodes (FP LDs) is proposed and experimentally demonstrated. Unlike the traditional hybrid WoF transmission systems that require multiple distributed feedback (DFB) LDs to support different kinds of services, the proposed system employs multiple injection-locked FP LDs to provide different kinds of applications. Such a hybrid WoF transmission system delivers downstream intensity-modulated 20-GHz microwave (MW)/60-GHz millimeter-wave (MMW)/550-MHz cable television (CATV) signals and upstream phase-remodulated 20-GHz MW signal. Excellent bit error rate (BER), carrier-to-noise ratio (CNR), composite second-order (CSO), and composite triple-beat (CTB) are observed over a 40-km single-mode fiber (SMF) and a 4-m radio frequency (RF) wireless transport. Such a hybrid WoF transmission system has practical applications for fiber-wireless convergence to provide broadband integrated services, including telecommunication, data communication, and CATV services.

Parameters optimization for magnetic resonance coupling wireless power transmission.

Science.gov (United States)

Li, Changsheng; Zhang, He; Jiang, Xiaohua

2014-01-01

Taking maximum power transmission and power stable transmission as research objectives, optimal design for the wireless power transmission system based on magnetic resonance coupling is carried out in this paper. Firstly, based on the mutual coupling model, mathematical expressions of optimal coupling coefficients for the maximum power transmission target are deduced. Whereafter, methods of enhancing power transmission stability based on parameters optimal design are investigated. It is found that the sensitivity of the load power to the transmission parameters can be reduced and the power transmission stability can be enhanced by improving the system resonance frequency or coupling coefficient between the driving/pick-up coil and the transmission/receiving coil. Experiment results are well conformed to the theoretical analysis conclusions.

Wireless LAN security management with location detection capability in hospitals.

Science.gov (United States)

Tanaka, K; Atarashi, H; Yamaguchi, I; Watanabe, H; Yamamoto, R; Ohe, K

2012-01-01

In medical institutions, unauthorized access points and terminals obstruct the stable operation of a large-scale wireless local area network (LAN) system. By establishing a real-time monitoring method to detect such unauthorized wireless devices, we can improve the efficiency of security management. We detected unauthorized wireless devices by using a centralized wireless LAN system and a location detection system at 370 access points at the University of Tokyo Hospital. By storing the detected radio signal strength and location information in a database, we evaluated the risk level from the detection history. We also evaluated the location detection performance in our hospital ward using Wi-Fi tags. The presence of electric waves outside the hospital and those emitted from portable game machines with wireless communication capability was confirmed from the detection result. The location detection performance showed an error margin of approximately 4 m in detection accuracy and approximately 5% in false detection. Therefore, it was effective to consider the radio signal strength as both an index of likelihood at the detection location and an index for the level of risk. We determined the location of wireless devices with high accuracy by filtering the detection results on the basis of radio signal strength and detection history. Results of this study showed that it would be effective to use the developed location database containing radio signal strength and detection history for security management of wireless LAN systems and more general-purpose location detection applications.

[An implantable micro-device using wireless power transmission for measuring aortic aneurysm sac pressure].

Science.gov (United States)

Guo, Xudong; Ge, Bin; Wang, Wenxing

2013-08-01

In order to detect endoleaks after endovascular aneurysm repair (EVAR), we developed an implantable micro-device based on wireless power transmission to measure aortic aneurysm sac pressure. The implantable micro-device is composed of a miniature wireless pressure sensor, an energy transmitting coil, a data recorder and a data processing platform. Power transmission without interconnecting wires is performed by a transmitting coil and a receiving coil. The coupling efficiency of wireless power transmission depends on the coupling coefficient between the transmitting coil and the receiving coil. With theoretical analysis and experimental study, we optimized the geometry of the receiving coil to increase the coupling coefficient. In order to keep efficiency balance and satisfy the maximizing conditions, we designed a closed loop power transmission circuit, including a receiving voltage feedback module based on wireless communication. The closed loop improved the stability and reliability of transmission energy. The prototype of the micro-device has been developed and the experiment has been performed. The experiments showed that the micro-device was feasible and valid. For normal operation, the distance between the transmitting coil and the receiving coil is smaller than 8cm. Besides, the distance between the micro-device and the data recorder is within 50cm.

Wireless power transmission using ultrasonic guided waves

International Nuclear Information System (INIS)

Kural, A; Pullin, R; Featherston, C; Holford, K; Paget, C

2011-01-01

The unavailability of suitable power supply at desired locations is currently an important obstacle in the development of distributed, wireless sensor networks for applications such as structural health monitoring of aircraft. Proposed solutions range from improved batteries to energy harvesting from vibration, temperature gradients and other sources. A novel approach is being investigated at Cardiff University School of Engineering in cooperation with Airbus. It aims to utilise ultrasonic guided Lamb waves to transmit energy through the aircraft skin. A vibration generator is to be placed in a location where electricity supply is readily available. Ultrasonic waves generated by this device will travel through the aircraft structure to a receiver in a remote wireless sensor node. The receiver will convert the mechanical vibration of the ultrasonic waves back to electricity, which will be used to power the sensor node. This paper describes the measurement and modelling of the interference pattern which emerges when Lamb waves are transmitted continuously as in this power transmission application. The discovered features of the pattern, such as a large signal amplitude variation and a relatively high frequency, are presented and their importance for the development of a power transmission system is discussed.

Wireless power transmission using ultrasonic guided waves

Energy Technology Data Exchange (ETDEWEB)

Kural, A; Pullin, R; Featherston, C; Holford, K [School of Engineering, Cardiff University, Queens Buildings, The Parade, Cardiff CF24 2AA (United Kingdom); Paget, C, E-mail: kurala@cardiff.ac.uk [Airbus Operations Ltd, New Filton Road, BS99 7AR Bristol (United Kingdom)

2011-07-19

The unavailability of suitable power supply at desired locations is currently an important obstacle in the development of distributed, wireless sensor networks for applications such as structural health monitoring of aircraft. Proposed solutions range from improved batteries to energy harvesting from vibration, temperature gradients and other sources. A novel approach is being investigated at Cardiff University School of Engineering in cooperation with Airbus. It aims to utilise ultrasonic guided Lamb waves to transmit energy through the aircraft skin. A vibration generator is to be placed in a location where electricity supply is readily available. Ultrasonic waves generated by this device will travel through the aircraft structure to a receiver in a remote wireless sensor node. The receiver will convert the mechanical vibration of the ultrasonic waves back to electricity, which will be used to power the sensor node. This paper describes the measurement and modelling of the interference pattern which emerges when Lamb waves are transmitted continuously as in this power transmission application. The discovered features of the pattern, such as a large signal amplitude variation and a relatively high frequency, are presented and their importance for the development of a power transmission system is discussed.

Seamless Translation of Optical Fiber PolMux-OFDM into a 2x2 MIMO Wireless Transmission Enabled by Digital Training-Based Fiber-Wireless Channel Estimation

DEFF Research Database (Denmark)

Pang, Xiaodan; Zhao, Ying; Deng, Lei

2011-01-01

We propose and demonstrate a 2 × 2 multiple-input multiple-output (MIMO) wireless over fiber transmission system. Seamless translation of two orthogonal frequency division multiplexing (OFDM) signals on dual optical polarization states into wireless MIMO transmission at 795.5 Mbit/s net data rate...

Wireless cardiac action potential transmission with ultrasonically inserted silicon microprobes

International Nuclear Information System (INIS)

Shen, C J; Ramkumar, A; Lal, A; Gilmour, R F Jr

2011-01-01

This paper reports on the integration of ultrasonically inserted horn-shaped cardiac probes with wireless transmission of 3D cardiac action potential measurement for applications in ex vivo preparations such as monitoring the onset of ventricular fibrillation. Ultrasonically inserted silicon horn probes permit reduced penetration force during insertion, allowing silicon, a brittle material, to penetrate cardiac tissue. The probes also allow recording from multiple sites that are lithographically defined. An application-specific integrated circuit has been designed with a 40 dB amplifying stage and a frequency modulating oscillator at 95 MHz to wirelessly transmit the recorded action potentials. This ultrasonically inserted microprobe wireless system demonstrates the initial results in wireless monitoring of 3D action potential propagation, and the extraction of parameters of interest including the action potential duration and diastolic interval

Transport Schemes for Fiber-Wireless Technology: Transmission Performance and Energy Efficiency

Directory of Open Access Journals (Sweden)

Christina Lim

2014-04-01

Full Text Available Fiber-wireless technology has been actively researched as a potential candidate for next generation broadband wireless signal distribution. Despite the popularity, this hybrid scheme has many technical challenges that impede the uptake and commercial deployment. One of the inherent issues is the transport of the wireless signals over a predominantly digital optical network in today’s telecommunication infrastructure. Many different approaches have been introduced and demonstrated with digitized RF transport of the wireless signals being the most compatible with the existing optical fiber networks. In this paper, we review our work in the area of digitized RF transport to address the inherent issues related to analog transport in the fiber-wireless links and compare the transmission performance and energy efficiency with the other transport strategies.

Wireless transmission of monitoring data out of the Hades underground laboratory

International Nuclear Information System (INIS)

Schroeder, T.J.; Hart, J.

2012-01-01

Document available in extended abstract form only. For the monitoring of geological waste disposal in the post-closure phase, data acquired by the underground monitoring system inside the repository need to be transmitted wirelessly through the underground to the surface. Low frequency magneto-induction techniques as applied in mine communication and rescue can potentially be used for the wireless transmission of data from the repository to the surface. However, the propagation of magnetic fields through porous argillaceous rocks like the Boom Clay is hindered by the high electrical conductivity of the rock. As part of the European 7. framework project MoDeRn, Monitoring Developments for safe Repository operation and staged closure, NRG is conducting tests on the wireless transmission of monitoring data under conditions representative for a generic Dutch disposal in Boom Clay. This should help to judge the general feasibility of long-term wireless data transmission from an underground repository through the enclosing host rock and the overlying geosphere to the surface. Experimental work As contribution to the MoDeRn Work Package 3, In-situ demonstration of innovative monitoring techniques, NRG conducts tests on the wireless transmission of signals and data. The wireless data transmission experiments of NRG are being performed at the HADES Underground Research Laboratory (URL) in Mol, Belgium, situated at 225 m depth in a 100 m thick layer of Boom Clay. The main objective of the contribution is to quantify and optimise the energy efficiency of the transmission technique used. Because the Boom Clay and the overlying aquifers attenuate the magnetic fields more strongly than other host rocks, it is assumed that transmission experiments performed in the HADES give a more realistic picture on field propagation than experiments performed e.g. in granite, salt rock or Opalinus clay. Although the generic depth for the Dutch disposal design is 500 m, the experiments

Batteryless wireless transmission system for electronic drum uses piezoelectric generator for play signal and power source

International Nuclear Information System (INIS)

Nishikawa, H; Yoshimi, A; Takemura, K; Tanaka, A; Douseki, T

2015-01-01

A batteryless self-powered wireless transmission system has been developed that sends a signal from a drum pad to a synthesizer. The power generated by a piezoelectric generator functions both as the “Play” signal for the synthesizer and as the power source for the transmitter. An FM transmitter, which theoretically operates with zero latency, and a receiver with quick-response squelch of the received signal were developed for wireless transmission with a minimum system delay. Experimental results for an electronic drum without any connecting wires fully demonstrated the feasibility of self-powered wireless transmission with a latency of 900 μs. (paper)

Transmission Range Assignment with Balancing Connectivity in Clustered Wireless Networks

OpenAIRE

Hussein, Abd Ali

2014-01-01

Currently, the main challenge for researchers in the field of wireless sensor networks is associated with reducing the energy consumption as much as possible to increase the lifetime of the nodes and improve the performance of the network. Furthermore, delivery of data to its destination is also an important key issue that represents throughput of the network. On the other hand, transmission range assignment in clustered wireless networks is the bottleneck of the balance between energy con...

Wireless Power Transmission to Organic Light Emitting Diode Lighting Panel with Magnetically Coupled Resonator

Science.gov (United States)

Kim, Yong-Hae; Han, Jun-Han; Kang, Seung-Youl; Cheon, Sanghoon; Lee, Myung-Lae; Ahn, Seong-Deok; Zyung, Taehyoung; Lee, Jeong-Ik; Moon, Jaehyun; Chu, Hye Yong

2012-09-01

We are successful to lit the organic light emitting diode (OLED) lighting panel through the magnetically coupled wireless power transmission technology. For the wireless power transmission, we used the operation frequency 932 kHz, specially designed double spiral type transmitter, small and thin receiver on the four layered printed circuit board, and schottky diodes for the full bridge rectifier. Our white OLED is a hybrid type, in which phosphorescent and fluorescent organics are used together to generate stable white color. The total efficiency of power transmission is around 72%.

Investigation of interference in multiple-input multiple-output wireless transmission at W band for an optical wireless integration system.

Science.gov (United States)

Li, Xinying; Yu, Jianjun; Dong, Ze; Zhang, Junwen; Chi, Nan; Yu, Jianguo

2013-03-01

We experimentally investigate the interference in multiple-input multiple-output (MIMO) wireless transmission by adjusting the relative locations of horn antennas (HAs) in a 100 GHz optical wireless integration system, which can deliver a 50 Gb/s polarization-division-multiplexing quadrature-phase-shift-keying signal over 80 km single-mode fiber-28 and a 2×2 MIMO wireless link. For the parallel 2×2 MIMO wireless link, each receiver HA can only get wireless power from the corresponding transmitter HA, while for the crossover ones, the receiver HA can get wireless power from two transmitter HAs. At the wireless receiver, polarization demultiplexing is realized by the constant modulus algorithm (CMA) in the digital-signal-processing part. Compared to the parallel case, wireless interference causes about 2 dB optical signal-to-noise ratio penalty at a bit-error ratio (BER) of 3.8×10(-3) for the crossover cases if similar CMA taps are employed. The increase in CMA tap length can reduce wireless interference and improve BER performance. Furthermore, more CMA taps should be adopted to overcome the severe wireless interference when two pairs of transmitter and receiver HAs have different wireless distances.

Application of wireless power transmission systems in wireless capsule endoscopy: an overview.

Science.gov (United States)

Basar, Md Rubel; Ahmad, Mohd Yazed; Cho, Jongman; Ibrahim, Fatimah

2014-06-19

Wireless capsule endoscopy (WCE) is a promising technology for direct diagnosis of the entire small bowel to detect lethal diseases, including cancer and obscure gastrointestinal bleeding (OGIB). To improve the quality of diagnosis, some vital specifications of WCE such as image resolution, frame rate and working time need to be improved. Additionally, future multi-functioning robotic capsule endoscopy (RCE) units may utilize advanced features such as active system control over capsule motion, drug delivery systems, semi-surgical tools and biopsy. However, the inclusion of the above advanced features demands additional power that make conventional power source methods impractical. In this regards, wireless power transmission (WPT) system has received attention among researchers to overcome this problem. Systematic reviews on techniques of using WPT for WCE are limited, especially when involving the recent technological advancements. This paper aims to fill that gap by providing a systematic review with emphasis on the aspects related to the amount of transmitted power, the power transmission efficiency, the system stability and patient safety. It is noted that, thus far the development of WPT system for this WCE application is still in initial stage and there is room for improvements, especially involving system efficiency, stability, and the patient safety aspects.

Measurements on wireless transmission of ECG signals

International Nuclear Information System (INIS)

Gabrielli, A.; Lax, I.

2016-01-01

The scope of this research is to design an electronic prototype, an operative system as a proof of concept, to transmit and receive biological parameters, in particular electrocardiogram signals, through dedicated wireless circuits. The apparatus features microelectronics chips that were developed for more general biomedical applications, here adapted to deal with cardiac signals. The paper mainly focuses on the electronic aspects, as in this study we do not face medical or clinical aspects of the system. The transmitter circuit uses a commercial instrumentation amplifier and the receiver has been equipped with wide-band amplifiers along with made-in-the-lab band-pass filters centered at the carrier. We have been able to mount the entire system prototype into a preliminary data acquisition chain that reads out the electrocardiogram signal. The prototype allows acquiring the waveform, converting it to a digital pattern and open the transmission through a series of high-frequency packets exploiting the Ultra Wide Band protocol. The sensor value is embedded in the transmission through the rate of the digital packets. In fact, these are sent wireless at a specific packet-frequency that depends on the sensor amplitude and are detected into a receiver circuit that recovers the information.

Measurements on wireless transmission of ECG signals

Science.gov (United States)

Gabrielli, A.; Lax, I.

2016-12-01

The scope of this research is to design an electronic prototype, an operative system as a proof of concept, to transmit and receive biological parameters, in particular electrocardiogram signals, through dedicated wireless circuits. The apparatus features microelectronics chips that were developed for more general biomedical applications, here adapted to deal with cardiac signals. The paper mainly focuses on the electronic aspects, as in this study we do not face medical or clinical aspects of the system. The transmitter circuit uses a commercial instrumentation amplifier and the receiver has been equipped with wide-band amplifiers along with made-in-the-lab band-pass filters centered at the carrier. We have been able to mount the entire system prototype into a preliminary data acquisition chain that reads out the electrocardiogram signal. The prototype allows acquiring the waveform, converting it to a digital pattern and open the transmission through a series of high-frequency packets exploiting the Ultra Wide Band protocol. The sensor value is embedded in the transmission through the rate of the digital packets. In fact, these are sent wireless at a specific packet-frequency that depends on the sensor amplitude and are detected into a receiver circuit that recovers the information.

A Model for QoS - Aware Wireless Communication in Hospitals.

Science.gov (United States)

Alavikia, Zahra; Khadivi, Pejman; Hashemi, Masoud Reza

2012-01-01

In the recent decade, research regarding wireless applications in electronic health (e-Health) services has been increasing. The main benefits of using wireless technologies in e-Health applications are simple communications, fast delivery of medical information, reducing treatment cost and also reducing the medical workers' error rate. However, using wireless communications in sensitive healthcare environment raises electromagnetic interference (EMI). One of the most effective methods to avoid the EMI problem is power management. To this end, some of methods have been proposed in the literature to reduce EMI effects in health care environments. However, using these methods may result in nonaccurate interference avoidance and also may increase network complexity. To overcome these problems, we introduce two approaches based on per-user location and hospital sectoring for power management in sensitive healthcare environments. Although reducing transmission power could avoid EMI, it causes a number of successful message deliveries to the access point to decrease and, hence, the quality of service requirements cannot be meet. In this paper, we propose the use of relays for decreasing the probability of outage in the aforementioned scenario. Relay placement is the main factor to enjoy the usefulness of relay station benefits in the network and, therefore, we use the genetic algorithm to compute the optimum positions of a fixed number of relays. We have considered delay and maximum blind point coverage as two main criteria in relay station problem. The performance of the proposed method in outage reduction is investigated through simulations.

Secure and Efficient Data Transmission over Body Sensor and Wireless Networks

Directory of Open Access Journals (Sweden)

Madhur Sikri

2008-09-01

Full Text Available This paper addresses the transmission of medical and context-aware data from mobile patients to healthcare centers over heterogeneous wireless networks. A handheld device, called personal wireless hub (PWH, of each mobile patient first gathers and aggregates the vital sign and context-aware data for various telemedicine applications. PWH transmits the aggregated data to the remote healthcare center over multiple wireless interfaces such as cellular, WLAN, and WiMAX. The aggregated data contain both periodic data and those nonperiodic unpredictable emergency messages that are sporadic and delayintolerant. This paper addresses the problem of providing QoS (e.g., minimum delay, sufficient data rate, acceptable blocking, and/or dropping rate by designing a packet scheduling and channel/network allocation algorithm over wireless networks. The proposed resource-efficient QoS mechanism is simple and collaborates with an adaptive security algorithm. The QoS and security are achieved mainly with the collaboration of differentiator, delay monitor, data classifier, and scheduler modules within the PWH. This paper also discusses secure data transmission over body sensor networks by introducing key establishment and management algorithms. Simulation results show that the proposed framework achieves low-blocking probability, meets delay requirements, and provides energy-efficient secure communication for the combination of vital signs and context-aware data.

Secure and Efficient Data Transmission over Body Sensor and Wireless Networks

Directory of Open Access Journals (Sweden)

Challa Narasimha

2008-01-01

Full Text Available Abstract This paper addresses the transmission of medical and context-aware data from mobile patients to healthcare centers over heterogeneous wireless networks. A handheld device, called personal wireless hub (PWH, of each mobile patient first gathers and aggregates the vital sign and context-aware data for various telemedicine applications. PWH transmits the aggregated data to the remote healthcare center over multiple wireless interfaces such as cellular, WLAN, and WiMAX. The aggregated data contain both periodic data and those nonperiodic unpredictable emergency messages that are sporadic and delayintolerant. This paper addresses the problem of providing QoS (e.g., minimum delay, sufficient data rate, acceptable blocking, and/or dropping rate by designing a packet scheduling and channel/network allocation algorithm over wireless networks. The proposed resource-efficient QoS mechanism is simple and collaborates with an adaptive security algorithm. The QoS and security are achieved mainly with the collaboration of differentiator, delay monitor, data classifier, and scheduler modules within the PWH. This paper also discusses secure data transmission over body sensor networks by introducing key establishment and management algorithms. Simulation results show that the proposed framework achieves low-blocking probability, meets delay requirements, and provides energy-efficient secure communication for the combination of vital signs and context-aware data.

Wireless Sensor Network for Electric Transmission Line Monitoring

Energy Technology Data Exchange (ETDEWEB)

Alphenaar, Bruce

2009-06-30

Generally, federal agencies tasked to oversee power grid reliability are dependent on data from grid infrastructure owners and operators in order to obtain a basic level of situational awareness. Since there are many owners and operators involved in the day-to-day functioning of the power grid, the task of accessing, aggregating and analyzing grid information from these sources is not a trivial one. Seemingly basic tasks such as synchronizing data timestamps between many different data providers and sources can be difficult as evidenced during the post-event analysis of the August 2003 blackout. In this project we investigate the efficacy and cost effectiveness of deploying a network of wireless power line monitoring devices as a method of independently monitoring key parts of the power grid as a complement to the data which is currently available to federal agencies from grid system operators. Such a network is modeled on proprietary power line monitoring technologies and networks invented, developed and deployed by Genscape, a Louisville, Kentucky based real-time energy information provider. Genscape measures transmission line power flow using measurements of electromagnetic fields under overhead high voltage transmission power lines in the United States and Europe. Opportunities for optimization of the commercial power line monitoring technology were investigated in this project to enable lower power consumption, lower cost and improvements to measurement methodologies. These optimizations were performed in order to better enable the use of wireless transmission line monitors in large network deployments (perhaps covering several thousand power lines) for federal situational awareness needs. Power consumption and cost reduction were addressed by developing a power line monitor using a low power, low cost wireless telemetry platform known as the ''Mote''. Motes were first developed as smart sensor nodes in wireless mesh networking applications

A Novel Oscillating Rectenna for Wireless Microwave Power Transmission

Science.gov (United States)

McSpadden, J. O.; Dickinson, R. M.; Fan, L.; Chang, K.

1998-01-01

A new concept for solid state wireless microwave power transmission is presented. A 2.45 GHz rectenna element that was designed for over 85% RF to dc power conversion efficiency has been used to oscillate at 3.3 GHz with an approximate 1% dc to RF conversion efficiency.

Wireless high-speed data transmission with phosphorescent white-light LEDs

NARCIS (Netherlands)

Grubor, J.; Lee, S.C.J.; Langer, K-D.; Koonen, A.M.J.; Walewski, J.

2007-01-01

Wireless transmission exceeding 100 Mbit/s is demonstrated using a phosphorescent white-light LED in a lighting-like scenario. The data rate was achieved by detecting the blue part of the optical spectrum and applying discrete multi-tone modulation.

An asymmetric resonant coupling wireless power transmission link for Micro-Ball Endoscopy.

Science.gov (United States)

Sun, Tianjia; Xie, Xiang; Li, Guolin; Gu, Yingke; Deng, Yangdong; Wang, Ziqiang; Wang, Zhihua

2010-01-01

This paper investigates the design and optimization of a wireless power transmission link targeting Micro-Ball Endoscopy applications. A novel asymmetric resonant coupling structure is proposed to deliver power to an endoscopic Micro-Ball system for image read-out after it is excreted. Such a technology enables many key medical applications with stringent requirements for small system volume and high power delivery efficiency. A prototyping power transmission sub-system of the Micro-Ball system was implemented. It consists of primary coil, middle resonant coil, and cube-like full-direction secondary receiving coils. Our experimental results proved that 200mW of power can be successfully delivered. Such a wireless power transmission capability could satisfy the requirements of the Micro-Ball based endoscopy application. The transmission efficiency is in the range of 41% (worst working condition) to 53% (best working condition). Comparing to conventional structures, Asymmetric Resonant Coupling Structure improves power efficiency by 13%.

Energy Efficient Data Transmission for Sensors with Wireless Charging.

Science.gov (United States)

Fang, Xiaolin; Luo, Junzhou; Wu, Weiwei; Gao, Hong

2018-02-08

This paper studies the problem of maximizing the energy utilization for data transmission in sensors with periodical wireless charging process while taking into account the thermal effect. Two classes of problems are analyzed: one is the case that wireless charging can process for only a limited period of time, and the other is the case that wireless charging can process for a long enough time. Algorithms are proposed to solve the problems and analysis of these algorithms are also provided. For the first problem, three subproblems are studied, and, for the general problem, we give an algorithm that can derive a performance bound of ( 1 - 1 2 m ) ( O P T - E ) compared to an optimal solution. In addition, for the second problem, we provide an algorithm with 2 m 2 m - 1 O P T + 1 performance bound for the general problem. Simulations confirm the analysis of the algorithms.

Pre-hospital critical care by anaesthesiologist-staffed pre-hospital services in Scandinavia

DEFF Research Database (Denmark)

Krüger, A J; Lossius, H M; Mikkelsen, S

2013-01-01

All Scandinavian countries provide anaesthesiologist-staffed pre-hospital services. Little is known of the incidence of critical illness or injury attended by these services. We aimed to investigate anaesthesiologist-staffed pre-hospital services in Scandinavia with special emphasis on incidence...

Development of Wireless Techniques in Data and Power Transmission - Application for Particle Physics Detectors

CERN Document Server

Locci, E.; Dehos, C.; De Lurgio, P.; Djurcic, Z.; Drake, G.; Gimenez, J. L. Gonzalez; Gustafsson, L.; Kim, D.W.; Roehrich, D.; Schoening, A.; Siligaris, A.; Soltveit, H.K.; Ullaland, K.; Vincent, P.; Wiednert, D.; Yang, S.; Brenner, R.

2015-01-01

Wireless techniques have developed extremely fast over the last decade and using them for data and power transmission in particle physics detectors is not science- fiction any more. During the last years several research groups have independently thought of making it a reality. Wireless techniques became a mature field for research and new developments might have impact on future particle physics experiments. The Instrumentation Frontier was set up as a part of the SnowMass 2013 Community Summer Study [1] to examine the instrumentation R&D for the particle physics research over the coming decades: {\\guillemotleft} To succeed we need to make technical and scientific innovation a priority in the field {\\guillemotright}. Wireless data transmission was identified as one of the innovations that could revolutionize the transmission of data out of the detector. Power delivery was another challenge mentioned in the same report. We propose a collaboration to identify the specific needs of different projects that m...

Digital predistortion of 75–110 GHz W-band frequency multiplier for fiber wireless short range access systems

DEFF Research Database (Denmark)

Zhao, Ying; Deng, Lei; Pang, Xiaodan

2011-01-01

be effectively pre-compensated. Without using costly W-band components, a transmission system with 26km fiber and 4m wireless transmission operating at 99.6GHz is experimentally validated. Adjacent-channel power ratio (ACPR) improvements for IQ-modulated vector signals are guaranteed and transmission......We present a W-band fiber-wireless transmission system based on a nonlinear frequency multiplier for high-speed wireless short range access applications. By implementing a baseband digital signal predistortion scheme, intensive nonlinear distortions induced in a sextuple frequency multiplier can...... performances for fiber and wireless channels are studied. This W-band predistortion technique is a promising candidate for applications in high capacity wireless-fiber access systems....

Experimental and simulation analysis of the W-band SC-FDMA hybrid optical-wireless transmission

DEFF Research Database (Denmark)

Dogadaev, Anton Konstantinovich; Pang, Xiaodan; Deng, Lei

2014-01-01

We report on the experimental demonstration of the W-band hybrid optical-wireless SC-FDMA with 1.49 Gbit/s transmission over up to 2.3 m of air propagation. Provided simulation performance analysis proves a potential to reach 12.1 Gbit/s.......We report on the experimental demonstration of the W-band hybrid optical-wireless SC-FDMA with 1.49 Gbit/s transmission over up to 2.3 m of air propagation. Provided simulation performance analysis proves a potential to reach 12.1 Gbit/s....

160 Gbit/s photonics wireless transmission in the 300-500 GHz band

Directory of Open Access Journals (Sweden)

X. Yu

2016-11-01

Full Text Available To accommodate the ever increasing wireless traffic in the access networks, considerable efforts have been recently invested in developing photonics-assisted wireless communication systems with very high data rates. Superior to photonic millimeter-wave systems, terahertz (THz band (300 GHz-10 THz provides a much larger bandwidth and thus promises an extremely high capacity. However, the capacity potential of THz wireless systems has by no means been achieved yet. Here, we successfully demonstrate 160 Gbit/s wireless transmission by using a single THz emitter and modulating 25 GHz spaced 8 channels (20 Gbps per channel in the 300-500 GHz band, which is the highest bitrate in the frequency band above 300 GHz, to the best of our knowledge.

Fiber-wireless transmission system of 108  Gb/sdata over 80 km fiber and 2×2multiple-input multiple-output wireless links at 100 GHz W-band frequency.

Science.gov (United States)

Li, Xinying; Dong, Ze; Yu, Jianjun; Chi, Nan; Shao, Yufeng; Chang, G K

2012-12-15

We experimentally demonstrate a seamlessly integrated fiber-wireless system that delivers a 108  Gb/s signal through 80 km fiber and 1 m wireless transport over free space at 100 GHz adopting polarization-division-multiplexing quadrature-phase-shift-keying (PDM-QPSK) modulation and heterodyning coherent detection. The X- and Y-polarization components of the optical PDM-QPSK baseband signal are simultaneously upconverted to 100 GHz wireless carrier by optical polarization-diversity heterodyne beating, and then independently transmitted and received by two pairs of transmitter and receiver antennas, which form a 2×2 multiple-input multiple-output wireless link. At the wireless receiver, two-stage downconversion is performed firstly in the analog domain based on balanced mixer and sinusoidal radio frequency signal, and then in the digital domain based on digital signal processing (DSP). Polarization demultiplexing is realized by the constant modulus algorithm in the DSP part at the receiver. The bit-error ratio for the 108  Gb/s PDM-QPSK signal is less than the pre-forward-error-correction threshold of 3.8×10(-3) after both 1 m wireless delivery at 100 GHz and 80 km single-mode fiber-28 transmission. To our knowledge, this is the first demonstration to realize 100  Gb/s signal delivery through both fiber and wireless links at 100 GHz.

Full standard triple wireless transmission over 50m large core diameter graded index POF

NARCIS (Netherlands)

Shi, Y.; Morant, M.; Tangdiongga, E.; Llorente, R.; Koonen, A.M.J.

2011-01-01

We demonstrated for the first time a successful radio-over-1mm core diameter plastic optical fibre transmission of three simultaneous full standard wireless signals. Up to 50-m long transmission distance employing an eye-safe vertical cavity surface emitting laser has been achieved. The transmission

Watt-level wireless power transmission to multiple compact receivers

International Nuclear Information System (INIS)

Garraud, A; Munzer, D J; Althar, M; Garraud, N; Arnold, D P

2015-01-01

This paper reports an electrodynamic wireless power transmission (EWPT) system using a low-frequency (300 Hz) magnetic field to transmit watt-scale power levels to multiple compact receivers. As compared to inductively or resonantly coupled coils, EWPT facilitates transmission to multiple non-interacting receivers with little restriction on their orientation. A single 3.0 cm 3 receiver achieves 1.25 W power transmission with 8% efficiency at a distance of 1 cm (350 mW/cm 3 power density) from the transmitter. The same prototype achieves 9 mW at a distance of 9 cm. Moreover, we demonstrate simultaneous recharge of two wearable devices, using two receivers located in arbitrary positions and orientations. (paper)

Secure and Time-Aware Communication of Wireless Sensors Monitoring Overhead Transmission Lines.

Science.gov (United States)

Mazur, Katarzyna; Wydra, Michal; Ksiezopolski, Bogdan

2017-07-11

Existing transmission power grids suffer from high maintenance costs and scalability issues along with a lack of effective and secure system monitoring. To address these problems, we propose to use Wireless Sensor Networks (WSNs) as a technology to achieve energy efficient, reliable, and low-cost remote monitoring of transmission grids. With WSNs, smart grid enables both utilities and customers to monitor, predict and manage energy usage effectively and react to possible power grid disturbances in a timely manner. However, the increased application of WSNs also introduces new security challenges, especially related to privacy, connectivity, and security management, repeatedly causing unpredicted expenditures. Monitoring the status of the power system, a large amount of sensors generates massive amount of sensitive data. In order to build an effective Wireless Sensor Network (WSN) for a smart grid, we focus on designing a methodology of efficient and secure delivery of the data measured on transmission lines. We perform a set of simulations, in which we examine different routing algorithms, security mechanisms and WSN deployments in order to select the parameters that will not affect the delivery time but fulfill their role and ensure security at the same time. Furthermore, we analyze the optimal placement of direct wireless links, aiming at minimizing time delays, balancing network performance and decreasing deployment costs.

Wireless Energy and Information Transmission in FSO and RF-FSO Links

KAUST Repository

Makki, Behrooz; Svensson, Tommy; Buisman, Koen; Perez, Joaquin; Alouini, Mohamed-Slim

2017-01-01

We propose and analyze a wireless energy and information transmission scheme in free-space optical (FSO) links. The results are presented for both quasi-static and fast-fading conditions. We derive closed-form expressions for throughput, outage

Adaptive multi-node multiple input and multiple output (MIMO) transmission for mobile wireless multimedia sensor networks.

Science.gov (United States)

Cho, Sunghyun; Choi, Ji-Woong; You, Cheolwoo

2013-10-02

Mobile wireless multimedia sensor networks (WMSNs), which consist of mobile sink or sensor nodes and use rich sensing information, require much faster and more reliable wireless links than static wireless sensor networks (WSNs). This paper proposes an adaptive multi-node (MN) multiple input and multiple output (MIMO) transmission to improve the transmission reliability and capacity of mobile sink nodes when they experience spatial correlation. Unlike conventional single-node (SN) MIMO transmission, the proposed scheme considers the use of transmission antennas from more than two sensor nodes. To find an optimal antenna set and a MIMO transmission scheme, a MN MIMO channel model is introduced first, followed by derivation of closed-form ergodic capacity expressions with different MIMO transmission schemes, such as space-time transmit diversity coding and spatial multiplexing. The capacity varies according to the antenna correlation and the path gain from multiple sensor nodes. Based on these statistical results, we propose an adaptive MIMO mode and antenna set switching algorithm that maximizes the ergodic capacity of mobile sink nodes. The ergodic capacity of the proposed scheme is compared with conventional SN MIMO schemes, where the gain increases as the antenna correlation and path gain ratio increase.

Hybrid CATV/MMW/BB lightwave transmission system based on fiber-wired/fiber-wireless/fiber-VLLC integrations.

Science.gov (United States)

Li, Chung-Yi; Lu, Hai-Han; Lu, Ting-Chieh; Chu, Chien-An; Chen, Bo-Rui; Lin, Chun-Yu; Peng, Peng-Chun

2015-12-14

A hybrid lightwave transmission system for cable television (CATV)/millimeter-wave (MMW)/baseband (BB) signal transmission based on fiber-wired/fiber-wireless/fiber-visible laser light communication (VLLC) integrations is proposed and demonstrated. For down-link transmission, the light is intensity-modulated with 50-550 MHz CATV signal and optically promoted from 25 GHz radio frequency (RF) signal to 10 Gbps/50 GHz and 20 Gbps/100 GHz MMW data signals based on fiber-wired and fiber-wireless integrations. Good performances of carrier-to-noise ratio (CNR), composite second-order (CSO), composite triple-beat (CTB), and bit error rate (BER) are obtained over a 40-km single-mode fiber (SMF) and a 10-m RF wireless transport. For up-link transmission, the light is successfully intensity-remodulated with 5-Gbps BB data stream based on fiber-VLLC integration. Good BER performance is achieved over a 40-km SMF and a 10-m free-space VLLC transport. Such a hybrid CATV/MMW/BB lightwave transmission system is an attractive alternative, it gives the benefits of a communication link for broader bandwidth and higher transmission rate.

Up to 35 Gbps Ultra-Wideband Wireless Data Transmission Links

DEFF Research Database (Denmark)

Puerta Ramírez, Rafael; Rommel, Simon; Vegas Olmos, Juan José

2016-01-01

For the first time Ultra-Wideband record data transmission rates up to 35.1 Gbps and 21.6 Gbps are achieved, compliant with the restrictions on the effective radiated power established by both the United States Federal Communications Commission and the European Electronic Communications Committee......, respectively. To achieve these record bit rates, the multi-band approach of Carrierless Amplitude Phase modulation scheme was employed. Wireless transmissions were achieved with a BER below the 7% FEC threshold of 3.8·10-3 ....

Seamless integration of 57.2-Gb/s signal wireline transmission and 100-GHz wireless delivery.

Science.gov (United States)

Li, Xinying; Yu, Jianjun; Dong, Ze; Cao, Zizheng; Chi, Nan; Zhang, Junwen; Shao, Yufeng; Tao, Li

2012-10-22

We experimentally demonstrated the seamless integration of 57.2-Gb/s signal wireline transmission and 100-GHz wireless delivery adopting polarization-division-multiplexing quadrature-phase-shift-keying (PDM-QPSK) modulation with 400-km single-mode fiber-28 (SMF-28) transmission and 1-m wireless delivery. The X- and Y-polarization components of optical PDM-QPSK baseband signal are simultaneously up-converted to 100 GHz by optical polarization-diversity heterodyne beating, and then independently transmitted and received by two pairs of transmitter and receiver antennas, which make up a 2x2 multiple-input multiple-output (MIMO) wireless link based on microwave polarization multiplexing. At the wireless receiver, a two-stage down conversion is firstly done in analog domain based on balanced mixer and sinusoidal radio frequency (RF) signal, and then in digital domain based on digital signal processing (DSP). Polarization de-multiplexing is realized by constant modulus algorithm (CMA) based on DSP in heterodyne coherent detection. Our experimental results show that more taps are required for CMA when the X- and Y-polarization antennas have different wireless distance.

Analysis of transmission properties in an indoor wireless sensor network based on a full-factorial design

International Nuclear Information System (INIS)

Christmann, Dennis; Martinovic, Ivan; Schmitt, Jens B

2010-01-01

In this paper, we systematically investigate different factors and their effects on the wireless transmission properties using a full-factorial experimental design of a wireless sensor network in a real-world indoor environment. We quantify the impact of primary factors such as the wireless channel, physical position, transmission power and line of sight, as well as their interactions on the received signal strength (RSS). While some of our results support conventional assumptions, this study also shows that there are several properties which are in contrast to existing findings. For example, there is no significant correlation in the measured RSS between differently located but equally distant transmitters, yet the correlation coefficient for the two directions of a single link between two transmitters is above 94%, leading to very symmetric links that differ only in a few dBm for the two directions. Further analysis reveals the strong interaction of transmission frequency and physical position, while the transmission power has only an isolated, non-interacting effect on the RSS. Since the analyzed network consists of commodity motes utilizing TI's well-known IEEE 802.15.4 compliant CC2420 transceiver, the results of this experimental analysis can serve as valuable insights in planning and deploying wireless sensor networks in different application scenarios

Hybrid digital-analog video transmission in wireless multicast and multiple-input multiple-output system

Science.gov (United States)

Liu, Yu; Lin, Xiaocheng; Fan, Nianfei; Zhang, Lin

2016-01-01

Wireless video multicast has become one of the key technologies in wireless applications. But the main challenge of conventional wireless video multicast, i.e., the cliff effect, remains unsolved. To overcome the cliff effect, a hybrid digital-analog (HDA) video transmission framework based on SoftCast, which transmits the digital bitstream with the quantization residuals, is proposed. With an effective power allocation algorithm and appropriate parameter settings, the residual gains can be maximized; meanwhile, the digital bitstream can assure transmission of a basic video to the multicast receiver group. In the multiple-input multiple-output (MIMO) system, since nonuniform noise interference on different antennas can be regarded as the cliff effect problem, ParCast, which is a variation of SoftCast, is also applied to video transmission to solve it. The HDA scheme with corresponding power allocation algorithms is also applied to improve video performance. Simulations show that the proposed HDA scheme can overcome the cliff effect completely with the transmission of residuals. What is more, it outperforms the compared WSVC scheme by more than 2 dB when transmitting under the same bandwidth, and it can further improve performance by nearly 8 dB in MIMO when compared with the ParCast scheme.

Self-powered wireless carbohydrate/oxygen sensitive biodevice based on radio signal transmission.

Science.gov (United States)

Falk, Magnus; Alcalde, Miguel; Bartlett, Philip N; De Lacey, Antonio L; Gorton, Lo; Gutierrez-Sanchez, Cristina; Haddad, Raoudha; Kilburn, Jeremy; Leech, Dónal; Ludwig, Roland; Magner, Edmond; Mate, Diana M; Conghaile, Peter Ó; Ortiz, Roberto; Pita, Marcos; Pöller, Sascha; Ruzgas, Tautgirdas; Salaj-Kosla, Urszula; Schuhmann, Wolfgang; Sebelius, Fredrik; Shao, Minling; Stoica, Leonard; Sygmund, Cristoph; Tilly, Jonas; Toscano, Miguel D; Vivekananthan, Jeevanthi; Wright, Emma; Shleev, Sergey

2014-01-01

Here for the first time, we detail self-contained (wireless and self-powered) biodevices with wireless signal transmission. Specifically, we demonstrate the operation of self-sustained carbohydrate and oxygen sensitive biodevices, consisting of a wireless electronic unit, radio transmitter and separate sensing bioelectrodes, supplied with electrical energy from a combined multi-enzyme fuel cell generating sufficient current at required voltage to power the electronics. A carbohydrate/oxygen enzymatic fuel cell was assembled by comparing the performance of a range of different bioelectrodes followed by selection of the most suitable, stable combination. Carbohydrates (viz. lactose for the demonstration) and oxygen were also chosen as bioanalytes, being important biomarkers, to demonstrate the operation of the self-contained biosensing device, employing enzyme-modified bioelectrodes to enable the actual sensing. A wireless electronic unit, consisting of a micropotentiostat, an energy harvesting module (voltage amplifier together with a capacitor), and a radio microchip, were designed to enable the biofuel cell to be used as a power supply for managing the sensing devices and for wireless data transmission. The electronic system used required current and voltages greater than 44 µA and 0.57 V, respectively to operate; which the biofuel cell was capable of providing, when placed in a carbohydrate and oxygen containing buffer. In addition, a USB based receiver and computer software were employed for proof-of concept tests of the developed biodevices. Operation of bench-top prototypes was demonstrated in buffers containing different concentrations of the analytes, showcasing that the variation in response of both carbohydrate and oxygen biosensors could be monitored wirelessly in real-time as analyte concentrations in buffers were changed, using only an enzymatic fuel cell as a power supply.

Self-powered wireless carbohydrate/oxygen sensitive biodevice based on radio signal transmission.

Directory of Open Access Journals (Sweden)

Magnus Falk

Full Text Available Here for the first time, we detail self-contained (wireless and self-powered biodevices with wireless signal transmission. Specifically, we demonstrate the operation of self-sustained carbohydrate and oxygen sensitive biodevices, consisting of a wireless electronic unit, radio transmitter and separate sensing bioelectrodes, supplied with electrical energy from a combined multi-enzyme fuel cell generating sufficient current at required voltage to power the electronics. A carbohydrate/oxygen enzymatic fuel cell was assembled by comparing the performance of a range of different bioelectrodes followed by selection of the most suitable, stable combination. Carbohydrates (viz. lactose for the demonstration and oxygen were also chosen as bioanalytes, being important biomarkers, to demonstrate the operation of the self-contained biosensing device, employing enzyme-modified bioelectrodes to enable the actual sensing. A wireless electronic unit, consisting of a micropotentiostat, an energy harvesting module (voltage amplifier together with a capacitor, and a radio microchip, were designed to enable the biofuel cell to be used as a power supply for managing the sensing devices and for wireless data transmission. The electronic system used required current and voltages greater than 44 µA and 0.57 V, respectively to operate; which the biofuel cell was capable of providing, when placed in a carbohydrate and oxygen containing buffer. In addition, a USB based receiver and computer software were employed for proof-of concept tests of the developed biodevices. Operation of bench-top prototypes was demonstrated in buffers containing different concentrations of the analytes, showcasing that the variation in response of both carbohydrate and oxygen biosensors could be monitored wirelessly in real-time as analyte concentrations in buffers were changed, using only an enzymatic fuel cell as a power supply.

Micro-intestinal robot with wireless power transmission: design, analysis and experiment.

Science.gov (United States)

Shi, Yu; Yan, Guozheng; Chen, Wenwen; Zhu, Bingquan

2015-11-01

Video capsule endoscopy is a useful tool for noninvasive intestinal detection, but it is not capable of active movement; wireless power is an effective solution to this problem. The research in this paper consists of two parts: the mechanical structure which enables the robot to move smoothly inside the intestinal tract, and the wireless power supply which ensures efficiency. First, an intestinal robot with leg architectures was developed based on the Archimedes spiral, which mimics the movement of an inchworm. The spiral legs were capable of unfolding to an angle of approximately 155°, which guaranteed stability of clamping, consistency of surface pressure, and avoided the risk of puncturing the intestinal tract. Secondly, the necessary power to operate the robot was far beyond the capacity of button batteries, so a wireless power transmission (WPT) platform was developed. The design of the platform focused on power transfer efficiency and frequency stability. In addition, the safety of human tissue in the alternating electromagnetic field was also taken into consideration. Finally, the assembled robot was tested and verified with the use of the WPT platform. In the isolated intestine, the robot system successfully traveled along the intestine with an average speed of 23 mm per minute. The obtained videos displayed a resolution of 320 × 240 and a transmission rate of 30 frames per second. The WPT platform supplied up to 500 mW of energy to the robot, and achieved a power transfer efficiency of 12%. It has been experimentally verified that the intestinal robot is safe and effective as an endoscopy tool, for which wireless power is feasible. Proposals for further improving the robot and wireless power supply are provided later in this paper. Copyright © 2015 Elsevier Ltd. All rights reserved.

Evaluation of video transmission of MAC protocols in wireless sensor network

Science.gov (United States)

Maulidin, Mahmuddin, M.; Kamaruddin, L. M.; Elsaikh, Mohamed

2016-08-01

Wireless Sensor Network (WSN) is a wireless network which consists of sensor nodes scattered in a particular area which are used to monitor physical or environment condition. Each node in WSN is also scattered in sensor field, so an appropriate scheme of MAC protocol should have to develop communication link for data transferring. Video transmission is one of the important applications for the future that can be transmitted with low aspect in side of cost and also power consumption. In this paper, comparison of five different MAC WSN protocol for video transmission namely IEEE 802.11 standard, IEEE 802.15.4 standard, CSMA/CA, Berkeley-MAC, and Lightweight-MAC protocol are studied. Simulation experiment has been conducted in OMNeT++ with INET network simulator software to evaluate the performance. Obtained results indicate that IEEE 802.11 works better than other protocol in term of packet delivery, throughput, and latency.

Efficiency optimization of wireless power transmission systems for active capsule endoscopes.

Science.gov (United States)

Zhiwei, Jia; Guozheng, Yan; Jiangpingping; Zhiwu, Wang; Hua, Liu

2011-10-01

Multipurpose active capsule endoscopes have drawn considerable attention in recent years, but these devices continue to suffer from energy limitations. A wireless power supply system is regarded as a practical way to overcome the power shortage problem in such devices. This paper focuses on the efficiency optimization of a wireless energy supply system with size and safety constraints. A mathematical programming model in which these constraints are considered is proposed for transmission efficiency, optimal frequency and current, and overall system effectiveness. To verify the feasibility of the proposed method, we use a wireless active capsule endoscope as an illustrative example. The achieved efficiency can be regarded as an index for evaluating the system, and the proposed approach can be used to direct the design of transmitting and receiving coils.

Efficiency optimization of wireless power transmission systems for active capsule endoscopes

International Nuclear Information System (INIS)

Zhiwei, Jia; Guozheng, Yan; Jiangpingping; Zhiwu, Wang; Hua, Liu

2011-01-01

Multipurpose active capsule endoscopes have drawn considerable attention in recent years, but these devices continue to suffer from energy limitations. A wireless power supply system is regarded as a practical way to overcome the power shortage problem in such devices. This paper focuses on the efficiency optimization of a wireless energy supply system with size and safety constraints. A mathematical programming model in which these constraints are considered is proposed for transmission efficiency, optimal frequency and current, and overall system effectiveness. To verify the feasibility of the proposed method, we use a wireless active capsule endoscope as an illustrative example. The achieved efficiency can be regarded as an index for evaluating the system, and the proposed approach can be used to direct the design of transmitting and receiving coils

Installation of secure, always available wireless LAN systems as a component of the hospital communication infrastructure.

Science.gov (United States)

Hanada, Eisuke; Kudou, Takato; Tsumoto, Shusaku

2013-06-01

Wireless technologies as part of the data communication infrastructure of modern hospitals are being rapidly introduced. Even though there are concerns about problems associated with wireless communication security, the demand is remarkably large. In addition, insuring that the network is always available is important. Herein, we discuss security countermeasures and points to insure availability that must be taken to insure safe hospital/business use of wireless LAN systems, referring to the procedures introduced at Shimane University Hospital. Security countermeasures differ according to their purpose, such as for preventing illegal use or insuring availability, both of which are discussed. It is our hope that this information will assist others in their efforts to insure safe implementation of wireless LAN systems, especially in hospitals where they have the potential to greatly improve information sharing and patient safety.

A Model for QoS – Aware Wireless Communication in Hospitals

Science.gov (United States)

Alavikia, Zahra; Khadivi, Pejman; Hashemi, Masoud Reza

2012-01-01

In the recent decade, research regarding wireless applications in electronic health (e-Health) services has been increasing. The main benefits of using wireless technologies in e-Health applications are simple communications, fast delivery of medical information, reducing treatment cost and also reducing the medical workers’ error rate. However, using wireless communications in sensitive healthcare environment raises electromagnetic interference (EMI). One of the most effective methods to avoid the EMI problem is power management. To this end, some of methods have been proposed in the literature to reduce EMI effects in health care environments. However, using these methods may result in nonaccurate interference avoidance and also may increase network complexity. To overcome these problems, we introduce two approaches based on per-user location and hospital sectoring for power management in sensitive healthcare environments. Although reducing transmission power could avoid EMI, it causes a number of successful message deliveries to the access point to decrease and, hence, the quality of service requirements cannot be meet. In this paper, we propose the use of relays for decreasing the probability of outage in the aforementioned scenario. Relay placement is the main factor to enjoy the usefulness of relay station benefits in the network and, therefore, we use the genetic algorithm to compute the optimum positions of a fixed number of relays. We have considered delay and maximum blind point coverage as two main criteria in relay station problem. The performance of the proposed method in outage reduction is investigated through simulations. PMID:23493832

TD-LTE Wireless Private Network QoS Transmission Protection

Science.gov (United States)

Zhang, Jianming; Cheng, Chao; Wu, Zanhong

With the commencement of construction of the smart grid, the demand power business for reliability and security continues to improve, the reliability transmission of power TD-LTE Wireless Private Network are more and more attention. For TD-LTE power private network, it can provide different QoS services according to the user's business type, to protect the reliable transmission of business. This article describes in detail the AF module of PCC in the EPC network, specifically introduces set up AF module station and QoS mechanisms in the EPS load, fully considers the business characteristics of the special power network, establishing a suitable architecture for mapping QoS parameters, ensuring the implementation of each QoS business. Through using radio bearer management, we can achieve the reliable transmission of each business on physical channel.

Wireless electricity (Power) transmission using solar based power satellite technology

International Nuclear Information System (INIS)

Maqsood, M; Nasir, M Nauman

2013-01-01

In the near future due to extensive use of energy, limited supply of resources and the pollution in environment from present resources e.g. (wood, coal, fossil fuel) etc, alternative sources of energy and new ways to generate energy which are efficient, cost effective and produce minimum losses are of great concern. Wireless electricity (Power) transmission (WET) has become a focal point as research point of view and nowadays lies at top 10 future hot burning technologies that are under research these days. In this paper, we present the concept of transmitting power wirelessly to reduce transmission and distribution losses. The wired distribution losses are 70 – 75% efficient. We cannot imagine the world without electric power which is efficient, cost effective and produce minimum losses is of great concern. This paper tells us the benefits of using WET technology specially by using Solar based Power satellites (SBPS) and also focuses that how we make electric system cost effective, optimized and well organized. Moreover, attempts are made to highlight future issues so as to index some emerging solutions.

Electromagnetic Interference Issues of A Wireless Power Transmission Converter

DEFF Research Database (Denmark)

Khazraj, Hesam; Haji Bashi, Mazaher; Silva, Filipe Miguel Faria da

2018-01-01

field and the leakage current flowing through stray capacitors. In this paper, the EMI of wireless power transmission technology is highlighted and for the first time evaluated from a new perspective. The possible parasitic paths are identified simply. Additionally, effective high-frequency models......Many recent studies have focused on the inductive charging to transfer electrical power from a source to batteries without any electrical interface. The main problem with them is that inductive charging technologies may have electromagnetic compatibility (EMC) issues caused by the leakage magnetic...... for each part of the inductive charger are presented. At the first, the lowest EMI technology for wireless charging is chosen and simulated. To overcome the EMI and leakage current problems, this paper also suggests using a new passive EMI filter topology. Simulation results show the necessity...

Design of a telemetry system based on wireless power transmission for physiological parameter monitoring

International Nuclear Information System (INIS)

Jia, Zhiwei; Yan, Guozheng; Zhu, Bingquan

2015-01-01

An implanted telemetry system for experimental animals with or without anaesthesia can be used to continuously monitor physiological parameters. This system is significant not only in the study of organisms but also in the evaluation of drug efficacy, artificial organs, and auxiliary devices. The system is composed of a miniature electronic capsule, a wireless power transmission module, a data-recording device, and a processing module. An electrocardiograph, a temperature sensor, and a pressure sensor are integrated in the miniature electronic capsule, in which the signals are transmitted in vitro by wireless communication after filtering, amplification, and A/D sampling. To overcome the power shortage of batteries, a wireless power transmission module based on electromagnetic induction was designed. The transmitting coil of a rectangular-section solenoid and a 3D receiving coil are proposed according to stability and safety constraints. Experiments show that at least 150 mW of power could pick up on the load in a volume of Φ10.5 mm × 11 mm, with a transmission efficiency of 2.56%. Vivisection experiments verified the feasibility of the integrated radio-telemetry system

Design of a telemetry system based on wireless power transmission for physiological parameter monitoring

Energy Technology Data Exchange (ETDEWEB)

Jia, Zhiwei, E-mail: jiayege@hotmail.com [College of Electrical and Information Engineering, Changsha University of Science and Technology, Changsha (China); Yan, Guozheng; Zhu, Bingquan [820 Institute, School of Electronic Information and Electrical Engineering, Shanghai Jiao Tong University, Shanghai (China)

2015-04-15

An implanted telemetry system for experimental animals with or without anaesthesia can be used to continuously monitor physiological parameters. This system is significant not only in the study of organisms but also in the evaluation of drug efficacy, artificial organs, and auxiliary devices. The system is composed of a miniature electronic capsule, a wireless power transmission module, a data-recording device, and a processing module. An electrocardiograph, a temperature sensor, and a pressure sensor are integrated in the miniature electronic capsule, in which the signals are transmitted in vitro by wireless communication after filtering, amplification, and A/D sampling. To overcome the power shortage of batteries, a wireless power transmission module based on electromagnetic induction was designed. The transmitting coil of a rectangular-section solenoid and a 3D receiving coil are proposed according to stability and safety constraints. Experiments show that at least 150 mW of power could pick up on the load in a volume of Φ10.5 mm × 11 mm, with a transmission efficiency of 2.56%. Vivisection experiments verified the feasibility of the integrated radio-telemetry system.

Full-duplex bidirectional transmission of 10-Gb/s millimeter-wave QPSK signal in E-band optical wireless link.

Science.gov (United States)

Fang, Yuan; Yu, Jianjun; Chi, Nan; Xiao, Jiangnan

2014-01-27

We experimentally demonstrated full-duplex bidirectional transmission of 10-Gb/s millimeter-wave (mm-wave) quadrature phase shift keying (QPSK) signal in E-band (71-76 GHz and 81-86 GHz) optical wireless link. Single-mode fibers (SMF) are connected at both sides of the antenna for uplink and downlink which realize 40-km SMF and 2-m wireless link for bidirectional transmission simultaneously. We utilized multi-level modulation format and coherent detection in such E-band optical wireless link for the first time. Mm-wave QPSK signal is generated by photonic technique to increase spectrum efficiency and received signal is coherently detected to improve receiver sensitivity. After the coherent detection, digital signal processing is utilized to compensate impairments of devices and transmission link.

Wireless image-data transmission from an implanted image sensor through a living mouse brain by intra body communication

Science.gov (United States)

Hayami, Hajime; Takehara, Hiroaki; Nagata, Kengo; Haruta, Makito; Noda, Toshihiko; Sasagawa, Kiyotaka; Tokuda, Takashi; Ohta, Jun

2016-04-01

Intra body communication technology allows the fabrication of compact implantable biomedical sensors compared with RF wireless technology. In this paper, we report the fabrication of an implantable image sensor of 625 µm width and 830 µm length and the demonstration of wireless image-data transmission through a brain tissue of a living mouse. The sensor was designed to transmit output signals of pixel values by pulse width modulation (PWM). The PWM signals from the sensor transmitted through a brain tissue were detected by a receiver electrode. Wireless data transmission of a two-dimensional image was successfully demonstrated in a living mouse brain. The technique reported here is expected to provide useful methods of data transmission using micro sized implantable biomedical sensors.

DEVELOPMENT OF WIRELESS TECHNIQUES IN DATA AND POWER TRANSMISSION APPLICATION FOR PARTICLE-PHYSICS DETECTORS

CERN Document Server

Brenner, R; Dehos, C; De Lurgio, P; Djurcic, Z; Drake, G; Gonzales Gimenez, JL; Gustafsson, L; Kim, DW; Locci, E; Pfeiffer, U; Röhrich, D; Rydberg, D; Schöning, A; Siligaris, A; Soltveit, HK; Ullaland, K; Vincent, P; Vasquez, PR; Wiedner, D; Yang, S

2017-01-01

In the WADAPT project described in this Letter of Intent, we propose to develop wireless techniques for data and power transmission in particle-physics detectors. Wireless techniques have developed extremely fast over the last decade and are now mature for being considered as a promising alternative to cables and optical links that would revolutionize the detector design. The WADAPT consortium has been formed to identify the specific needs of different projects that might benefit from wireless techniques with the objective of providing a common platform for research and development in order to optimize effectiveness and cost. The proposed R&D will aim at designing and testing wireless demonstrators for large instrumentation systems.

Digital Photonic Receivers for Wireless and Wireline Optical Fiber Transmission Links

DEFF Research Database (Denmark)

Guerrero Gonzalez, Neil

services. The experimental demonstration supported the following transmissions systems: a baseband, 5 Gbps, intensity modulation system employing a directly modulated vertical cavity surface emitting laser (VCSEL), a baseband 20 Gbps non-return-to-zero quadrature phase-shift keying (NRZ-QPSK) system...... receivers in hybrid wireless and wireline optical fiber transmission links. Furthermore, the digital signal processing framework presented in this thesis can be extended to design probabilistic-based digital photonic receivers that can find applications in cognitive heterogeneous reconfigurable optical...

Impedance matching wireless power transmission system for biomedical devices.

Science.gov (United States)

Lum, Kin Yun; Lindén, Maria; Tan, Tian Swee

2015-01-01

For medical application, the efficiency and transmission distance of the wireless power transfer (WPT) are always the main concern. Research has been showing that the impedance matching is one of the critical factors for dealing with the problem. However, there is not much work performed taking both the source and load sides into consideration. Both sides matching is crucial in achieving an optimum overall performance, and the present work proposes a circuit model analysis for design and implementation. The proposed technique was validated against experiment and software simulation. Result was showing an improvement in transmission distance up to 6 times, and efficiency at this transmission distance had been improved up to 7 times as compared to the impedance mismatch system. The system had demonstrated a near-constant transfer efficiency for an operating range of 2cm-12cm.

Mobile Robot Positioning with 433-MHz Wireless Motes with Varying Transmission Powers and a Particle Filter.

Science.gov (United States)

Canedo-Rodriguez, Adrian; Rodriguez, Jose Manuel; Alvarez-Santos, Victor; Iglesias, Roberto; Regueiro, Carlos V

2015-04-30

In wireless positioning systems, the transmitter's power is usually fixed. In this paper, we explore the use of varying transmission powers to increase the performance of a wireless localization system. To this extent, we have designed a robot positioning system based on wireless motes. Our motes use an inexpensive, low-power sub-1-GHz system-on-chip (CC1110) working in the 433-MHz ISM band. Our localization algorithm is based on a particle filter and infers the robot position by: (1) comparing the power received with the expected one; and (2) integrating the robot displacement. We demonstrate that the use of transmitters that vary their transmission power over time improves the performance of the wireless positioning system significantly, with respect to a system that uses fixed power transmitters. This opens the door for applications where the robot can localize itself actively by requesting the transmitters to change their power in real time.

Mobile Robot Positioning with 433-MHz Wireless Motes with Varying Transmission Powers and a Particle Filter

Directory of Open Access Journals (Sweden)

Adrian Canedo-Rodriguez

2015-04-01

Full Text Available In wireless positioning systems, the transmitter’s power is usually fixed. In this paper, we explore the use of varying transmission powers to increase the performance of a wireless localization system. To this extent, we have designed a robot positioning system based on wireless motes. Our motes use an inexpensive, low-power sub-1-GHz system-on-chip (CC1110 working in the 433-MHz ISM band. Our localization algorithm is based on a particle filter and infers the robot position by: (1 comparing the power received with the expected one; and (2 integrating the robot displacement. We demonstrate that the use of transmitters that vary their transmission power over time improves the performance of the wireless positioning system significantly, with respect to a system that uses fixed power transmitters. This opens the door for applications where the robot can localize itself actively by requesting the transmitters to change their power in real time.

Decentralized control of transmission rates in energy-critical wireless networks

KAUST Repository

Xia, Li

2013-06-01

In this paper, we discuss the decentralized optimization of delay and energy consumption in a multi-hop wireless network. The goal is to minimize the energy consumption of energy-critical nodes and the overall packet transmission delay of the network. The transmission rates of energy-critical nodes are adjustable according to the local information of nodes, i.e., the length of packets queued. The multi-hop network is modeled as a queueing network.We prove that the system performance is monotone w.r.t. (with respect to) the transmission rate, thus the “bang-bang” control is an optimal control. We also prove that there exists a threshold type control policy which is optimal. We propose a decentralized algorithm to control transmission rates of these energy-critical nodes. Some simulation experiments are conducted to demonstrate the effectiveness of our approach.

Decentralized control of transmission rates in energy-critical wireless networks

KAUST Repository

Xia, Li; Shihada, Basem

2013-01-01

In this paper, we discuss the decentralized optimization of delay and energy consumption in a multi-hop wireless network. The goal is to minimize the energy consumption of energy-critical nodes and the overall packet transmission delay of the network. The transmission rates of energy-critical nodes are adjustable according to the local information of nodes, i.e., the length of packets queued. The multi-hop network is modeled as a queueing network.We prove that the system performance is monotone w.r.t. (with respect to) the transmission rate, thus the “bang-bang” control is an optimal control. We also prove that there exists a threshold type control policy which is optimal. We propose a decentralized algorithm to control transmission rates of these energy-critical nodes. Some simulation experiments are conducted to demonstrate the effectiveness of our approach.

Optical wireless connected objects for healthcare.

Science.gov (United States)

Toumieux, Pascal; Chevalier, Ludovic; Sahuguède, Stéphanie; Julien-Vergonjanne, Anne

2015-10-01

In this Letter the authors explore the communication capabilities of optical wireless technology for a wearable device dedicated to healthcare application. In an indoor environment sensible to electromagnetic perturbations such as a hospital, the use of optical wireless links can permit reducing the amount of radio frequencies in the patient environment. Moreover, this technology presents the advantage to be secure, low-cost and easy to deploy. On the basis of commercially available components, a custom-made wearable device is presented, which allows optical wireless transmission of accelerometer data in the context of physical activity supervision of post-stroke patients in hospital. Considering patient mobility, the experimental performance is established in terms of packet loss as a function of the number of receivers fixed to the ceiling. The results permit to conclude that optical wireless links can be used to perform such mobile remote monitoring applications. Moreover, based on the measurements obtained with one receiver, it is possible to theoretically determine the performance according to the number of receivers to be deployed.

Laser Energy Transmission for a Wireless Energy Supply to Robots

OpenAIRE

Kawashima, Nobuki; Takeda, Kazuya

2008-01-01

We can find a lot of robot applications in construction activities, where it is very difficult or dangerous for a man to access and only robots can work. The time will come soon when the actual use of those robots is extensively realized and the wireless energy transmission technology using laser is a unique means to supply energy to those robots.

A stable wireless energy transmission system for gastrointestinal microsystems.

Science.gov (United States)

Xin, W H; Yan, G Z; Wang, W X

2010-01-01

A wireless energy transmission system using a Helmholtz primary coil outside and a 3-dimensional secondary coil inside the body is introduced. It is designed to transmit stable power to a gastrointestinal microsystem regardless of its position and orientation when working in the gastric tract. Up to 310 mW of usable DC power can be delivered under worst-case geometrical conditions. Measured data of the system performance are presented and evaluated.

A fully integrated wireless system for intracranial direct cortical stimulation, real-time electrocorticography data transmission, and smart cage for wireless battery recharge.

Science.gov (United States)

Piangerelli, Marco; Ciavarro, Marco; Paris, Antonino; Marchetti, Stefano; Cristiani, Paolo; Puttilli, Cosimo; Torres, Napoleon; Benabid, Alim Louis; Romanelli, Pantaleo

2014-01-01

Wireless transmission of cortical signals is an essential step to improve the safety of epilepsy procedures requiring seizure focus localization and to provide chronic recording of brain activity for Brain Computer Interface (BCI) applications. Our group developed a fully implantable and externally rechargeable device, able to provide wireless electrocorticographic (ECoG) recording and cortical stimulation (CS). The first prototype of a wireless multi-channel very low power ECoG system was custom-designed to be implanted on non-human primates. The device, named ECOGIW-16E, is housed in a compact hermetically sealed Polyether ether ketone (PEEK) enclosure, allowing seamless battery recharge. ECOGIW-16E is recharged in a wireless fashion using a special cage designed to facilitate the recharge process in monkeys and developed in accordance with guidelines for accommodation of animals by Council of Europe (ETS123). The inductively recharging cage is made up of nylon and provides a thoroughly novel experimental setting on freely moving animals. The combination of wireless cable-free ECoG and external seamless battery recharge solves the problems and shortcomings caused by the presence of cables leaving the skull, providing a safer and easier way to monitor patients and to perform ECoG recording on primates. Data transmission exploits the newly available Medical Implant Communication Service band (MICS): 402-405 MHz. ECOGIW-16E was implanted over the left sensorimotor cortex of a macaca fascicularis to assess the feasibility of wireless ECoG monitoring and brain mapping through CS. With this device, we were able to record the everyday life ECoG signal from a monkey and to deliver focal brain stimulation with movement elicitation.

Power requirements and battery life measurement for wireless transmission between two nodes in different mediums

Directory of Open Access Journals (Sweden)

Radouane Karli

2017-06-01

Full Text Available One of the most important roles of the wireless sensor networks (WSN is to avoid wiring costs, be self-sustainable and be able to function for several years. However, due to the slow progress in battery technology, power continues to be a limited resource in wireless sensor communication and electric energy storage remains to be an important issue. On the other hand, if batteries must be replaced often, many remote sensing applications may become impractical. Therefore, batteries with long life on the order of several years are needed. This paper is an extension of work originally presented in The 5th International Conference on Electronic Devices, Systems and Applications to investigate further the power requirements for wireless data transfer between two nodes using batteries with different capacities (55 mAh, 550 mAh and 5500 mAh. In particular, the effect of a propagation medium such as air, distilled water and engine oil on the wireless communication inside a one meter long metallic pipe was investigated. Our first result shows a successful transmission of wireless signal through air, distilled water and oil medium with very low transmission losses. The second result shows that an increase in the battery capacity will increase the two-node wireless sensor operation time even in different propagation medium. This result can be used to determine the required battery capacity for extending the WSN operation time.

From early wireless to Everest.

Science.gov (United States)

Allen, A

1998-01-01

Medical information has been transmitted using wireless technologies for almost 80 years. A "wired wireless" electronic stethoscope was developed by the U.S. Army Signal Corps in the early 1920's, for potential use in ship-to-shore transmission of cardiac sounds. [Winters SR. Diagnosis by wireless. Scientific American June 11, 1921, p. 465] Today, wireless is used in a wide range of medical applications and at sites from transoceanic air flights to offshore oil platforms to Mt. Everest. 'Wireless LANs' are often used in medical environments. Typically, nurses and physicians in a hospital or clinic use hand-held "wireless thin client" pen computers that exchange patient information and images with the hospital server. Numerous companies, such as Fujitsu (article below) and Cruise Technologies (www.cruisetech.com) manufacture handheld pen-entry computers. One company, LXE, integrates radio-frequency (RF) enhanced hand-held computers specifically designed for production use within a wireless LAN (www.lxe.com). Other companies (Proxim, Symbol, and others) supply the wireless RF LAN infrastructure for the enterprise. Unfortunately, there have been problems with widespread deployment of wireless LANs. Perhaps the biggest impediment has been the lack of standards. Although an international standard (IEEE 802.11) was adopted in 1997, most wireless LAN products still are not compatible with the equipment of competing companies. A problem with the current standard for LAN adapters is that throughput is limited to 3 Mbps--compared to at least 10 Mbps, and often 100 Mbps, in a hard-wired Ethernet LAN. An II Mbps standard is due out in the next year or so, but it will be at least 2 years before standards-compliant products are available. This story profiles some of the ways that wireless is being used to overcome gaps in terrestrial and within-enterprise communication.

A 30 Gb/s full-duplex bi-directional transmission optical wireless-over fiber integration system at W-band.

Science.gov (United States)

Tang, Chanjuan; Yu, Jianjun; Li, Xinying; Chi, Nan; Xiao, Jiangnan; Tian, Yumin; Zhang, Junwen

2014-01-13

We propose and experimentally demonstrate a full-duplex bi-directional transmission optical wireless-over fiber integration system at W-band (75-100 GHz) with the speed up to 15 Gb/s for both 95.4 GHz link and 88.6 GHz link for the first time. The generation of millimeter-wave (mm-wave) wireless signal is based on the photonic technique by heterodyne mixing of an optical quadrature-phase-shift-keying (QPSK) signal with a free-running light at different wavelength. After 20 km fiber transmission, up to 30 Gb/s mm-wave signal is delivered over 2 m wireless link, and then converted to the optical signal for another 20 km fiber transmission. At the wireless receiver, coherent detection and advanced digital signal processing (DSP) are introduced to improve receiver sensitivity and system performance. With the OSNR of 15 dB, the bit error ratios (BERs) for 10 Gb/s signal transmission at 95.4 GHz and 88.6 GHz are below the forward-error-correction (FEC) threshold of 3.8 × 10(-3) whether post filter is used or not, while the BER for 15 Gb/s QPSK signal employing post filter in the link of 95.4 GHz is 2.9 × 10(-3).

Doubling transmission capacity in optical wireless system by antenna horizontal- and vertical-polarization multiplexing.

Science.gov (United States)

Li, Xinying; Yu, Jianjun; Zhang, Junwen; Dong, Ze; Chi, Nan

2013-06-15

We experimentally demonstrate 2×56 Gb/s two-channel polarization-division-multiplexing quadrature-phase-shift-keying signal delivery over 80 km single-mode fiber-28 and 2 m Q-band (33-50 GHz) wireless link, adopting antenna horizontal- (H-) and vertical-polarization (V-polarization) multiplexing. At the wireless receiver, classic constant-modulus-algorithm equalization based on digital signal processing can realize polarization demultiplexing and remove the crosstalk at the same antenna polarization. By adopting antenna polarization multiplexing, the signal baud rate and performance requirements for optical and wireless devices can be reduced but at the cost of double antennas and devices, while wireless transmission capacity can also be increased but at the cost of stricter requirements for V-polarization. The isolation is only about 19 dB when V-polarization deviation approaches 10°, which will affect high-speed (>50 Gb/s) wireless delivery.

Miniaturized Human Insertable Cardiac Monitoring System with Wireless Power Transmission Technique

Directory of Open Access Journals (Sweden)

Jong-Ha Lee

2016-01-01

Full Text Available Prolonged monitoring is more likely to diagnose atrial fibrillation accurately than intermittent or short-term monitoring. In this study, an implantable electrocardiograph (ECG sensor to monitor atrial fibrillation patients in real time was developed. The implantable sensor is composed of a micro controller unit, an analog-to-digital converter, a signal transmitter, an antenna, and two electrodes. The sensor detects ECG signals from the two electrodes and transmits these to an external receiver carried by the patient. Because the sensor continuously transmits signals, its battery consumption rate is extremely high; therefore, the sensor includes a wireless power transmission module that allows it to charge wirelessly from an external power source. The integrated sensor has the approximate dimensions 3 mm × 4 mm × 14 mm, which is small enough to be inserted into a patient without the need for major surgery. The signal and power transmission data sampling rate and frequency of the unit are 300 samples/s and 430 Hz, respectively. To validate the developed sensor, experiments were conducted on small animals.

An Energy-Efficient and High-Quality Video Transmission Architecture in Wireless Video-Based Sensor Networks

Directory of Open Access Journals (Sweden)

Yasaman Samei

2008-08-01

Full Text Available Technological progress in the fields of Micro Electro-Mechanical Systems (MEMS and wireless communications and also the availability of CMOS cameras, microphones and small-scale array sensors, which may ubiquitously capture multimedia content from the field, have fostered the development of low-cost limited resources Wireless Video-based Sensor Networks (WVSN. With regards to the constraints of videobased sensor nodes and wireless sensor networks, a supporting video stream is not easy to implement with the present sensor network protocols. In this paper, a thorough architecture is presented for video transmission over WVSN called Energy-efficient and high-Quality Video transmission Architecture (EQV-Architecture. This architecture influences three layers of communication protocol stack and considers wireless video sensor nodes constraints like limited process and energy resources while video quality is preserved in the receiver side. Application, transport, and network layers are the layers in which the compression protocol, transport protocol, and routing protocol are proposed respectively, also a dropping scheme is presented in network layer. Simulation results over various environments with dissimilar conditions revealed the effectiveness of the architecture in improving the lifetime of the network as well as preserving the video quality.

An Energy-Efficient and High-Quality Video Transmission Architecture in Wireless Video-Based Sensor Networks.

Science.gov (United States)

Aghdasi, Hadi S; Abbaspour, Maghsoud; Moghadam, Mohsen Ebrahimi; Samei, Yasaman

2008-08-04

Technological progress in the fields of Micro Electro-Mechanical Systems (MEMS) and wireless communications and also the availability of CMOS cameras, microphones and small-scale array sensors, which may ubiquitously capture multimedia content from the field, have fostered the development of low-cost limited resources Wireless Video-based Sensor Networks (WVSN). With regards to the constraints of videobased sensor nodes and wireless sensor networks, a supporting video stream is not easy to implement with the present sensor network protocols. In this paper, a thorough architecture is presented for video transmission over WVSN called Energy-efficient and high-Quality Video transmission Architecture (EQV-Architecture). This architecture influences three layers of communication protocol stack and considers wireless video sensor nodes constraints like limited process and energy resources while video quality is preserved in the receiver side. Application, transport, and network layers are the layers in which the compression protocol, transport protocol, and routing protocol are proposed respectively, also a dropping scheme is presented in network layer. Simulation results over various environments with dissimilar conditions revealed the effectiveness of the architecture in improving the lifetime of the network as well as preserving the video quality.

Auction-Based Resource Allocation for Cooperative Video Transmission Protocols over Wireless Networks

Directory of Open Access Journals (Sweden)

Zhu Han

2009-01-01

Full Text Available Cooperative transmission has been proposed as a novel transmission strategy that takes advantage of broadcast nature of wireless networks, forms virtual MIMO system, and provides diversity gains. In this paper, wireless video transmission protocols are proposed, in which the spectrum resources are first allocated for the source side to broadcast video packets to the relay and destination, and then for the relay side to transmit side information generated from the received packets. The proposed protocols are optimized to minimize the end-to-end expected distortion via choosing bandwidth/power allocation, configuration of side information, subject to bandwidth and power constraints. For multiuser cases, most of current resource allocation approaches cannot be naturally extended and applied to the networks with relay nodes for video transmission. This paper extends the share auction approach into the cooperative video communication scenarios and provides a near-optimal solution for resource allocation. Experimental results have demonstrated that the proposed approach has significant advantage of up to 4 dB gain in single user case and 1.3 dB gain in multiuser case over the reference systems in terms of peak-to-signal-noise ratio. In addition, it reduces the formidable computational complexity of the optimal solution to linear complexity with performance degradation of less than 0.3 dB.

Energy-efficient digital and wireless IC design for wireless smart sensing

Science.gov (United States)

Zhou, Jun; Huang, Xiongchuan; Wang, Chao; Tae-Hyoung Kim, Tony; Lian, Yong

2017-10-01

Wireless smart sensing is now widely used in various applications such as health monitoring and structural monitoring. In conventional wireless sensor nodes, significant power is consumed in wirelessly transmitting the raw data. Smart sensing adds local intelligence to the sensor node and reduces the amount of wireless data transmission via on-node digital signal processing. While the total power consumption is reduced compared to conventional wireless sensing, the power consumption of the digital processing becomes as dominant as wireless data transmission. This paper reviews the state-of-the-art energy-efficient digital and wireless IC design techniques for reducing the power consumption of the wireless smart sensor node to prolong battery life and enable self-powered applications.

Distortion-Based Link Adaptation for Wireless Video Transmission

Directory of Open Access Journals (Sweden)

Andrew Nix

2008-06-01

Full Text Available Wireless local area networks (WLANs such as IEEE 802.11a/g utilise numerous transmission modes, each providing different throughputs and reliability levels. Most link adaptation algorithms proposed in the literature (i maximise the error-free data throughput, (ii do not take into account the content of the data stream, and (iii rely strongly on the use of ARQ. Low-latency applications, such as real-time video transmission, do not permit large numbers of retransmission. In this paper, a novel link adaptation scheme is presented that improves the quality of service (QoS for video transmission. Rather than maximising the error-free throughput, our scheme minimises the video distortion of the received sequence. With the use of simple and local rate distortion measures and end-to-end distortion models at the video encoder, the proposed scheme estimates the received video distortion at the current transmission rate, as well as on the adjacent lower and higher rates. This allows the system to select the link-speed which offers the lowest distortion and to adapt to the channel conditions. Simulation results are presented using the MPEG-4/AVC H.264 video compression standard over IEEE 802.11g. The results show that the proposed system closely follows the optimum theoretic solution.

[Study on a wireless energy transmission system for the noninvasive examination micro system inside alimentary tracts].

Science.gov (United States)

He, Xiu; Yan, Guo-Zheng; Wang, Fu-Min

2008-01-01

A wireless energy transmission system for the MEMS system inside alimentary tracts is reported here in the paper. It consists of an automatic frequency tracking circuit of phase lock loop and phase shift PWM control circuit. Experimental results show that the energy transmission system is capable of automatic frequency-tracking and transmission power-adjusting and has stable received energy.

The remote transmission test of the GUAM measurement data by the wireless LAN

International Nuclear Information System (INIS)

Asano, Takashi; Fujiwara, Shigeo; Takahashi, Saburo; Nemoto, Tadayuki; Sato, Takashi; Kuniyasu, Kazufusa; Hiruta, Kazuhiko

2008-01-01

JAEA has developed and demonstrated the Remote Monitoring (RM) technology on the safeguards equipment at the storage area in PFPF to improve the efficiency of the inspection activity. JAEA is considering the expansion of the RM technology to the safeguards equipment in the process area to improve the efficiency of the inspection activity under the integrated safeguards. JAEA considers that the cabling cost and work in the facility will be reduced to apply the wireless LAN to the RM technology. JAEA performed the confirmatory testing of the performance of the Glove box Unattended Assay and Monitoring system (GUAM) and the remote transmission of the GUAM measurement data by the wireless LAN in cooperation with Japan Nuclear Fuel Limited. In this test, JAEA confirmed it's possible to establish the wireless LAN networking in the process area. This paper reports the applicability of the wireless LAN to the RM technology based on the results of the confirmatory testing. (author)

Experimental demonstration of 24-Gb/s CAP-64QAM radio-over-fiber system over 40-GHz mm-wave fiber-wireless transmission.

Science.gov (United States)

Zhang, Junwen; Yu, Jianjun; Chi, Nan; Li, Fan; Li, Xinying

2013-11-04

We propose and demonstrate a novel CAP-ROF system based on multi-level carrier-less amplitude and phase modulation (CAP) 64QAM with high spectrum efficiency for mm-wave fiber-wireless transmission. The performance of novel CAP modulation with high order QAM, for the first time, is investigated in the mm-wave fiber-wireless transmission system. One I/Q modulator is used for mm-wave generation and base-band signal modulation based on optical carrier suppression (OCS) and intensity modulation. Finally, we demonstrated a 24-Gb/s CAP-64QAM radio-over-fiber (ROF) system over 40-km stand single-mode-fiber (SMMF) and 1.5-m 38-GHz wireless transmission. The system operation factors are also experimentally investigated.

Feasibility of frequency-modulated wireless transmission for a multi-purpose MEMS-based accelerometer.

Science.gov (United States)

Sabato, Alessandro; Feng, Maria Q

2014-09-05

Recent advances in the Micro Electro-Mechanical System (MEMS) technology have made wireless MEMS accelerometers an attractive tool for Structural Health Monitoring (SHM) of civil engineering structures. To date, sensors' low sensitivity and accuracy--especially at very low frequencies--have imposed serious limitations for their application in monitoring large-sized structures. Conventionally, the MEMS sensor's analog signals are converted to digital signals before radio-frequency (RF) wireless transmission. The conversion can cause a low sensitivity to the important low-frequency and low-amplitude signals. To overcome this difficulty, the authors have developed a MEMS accelerometer system, which converts the sensor output voltage to a frequency-modulated signal before RF transmission. This is achieved by using a Voltage to Frequency Conversion (V/F) instead of the conventional Analog to Digital Conversion (ADC). In this paper, a prototype MEMS accelerometer system is presented, which consists of a transmitter and receiver circuit boards. The former is equipped with a MEMS accelerometer, a V/F converter and a wireless RF transmitter, while the latter contains an RF receiver and a F/V converter for demodulating the signal. The efficacy of the MEMS accelerometer system in measuring low-frequency and low-amplitude dynamic responses is demonstrated through extensive laboratory tests and experiments on a flow-loop pipeline.

Enhanced Wireless Power Transmission Using Strong Paramagnetic Response.

Science.gov (United States)

Ahn, Dukju; Kiani, Mehdi; Ghovanloo, Maysam

2014-03-01

A method of quasi-static magnetic resonant coupling has been presented for improving the power transmission efficiency (PTE) in near-field wireless power transmission, which improves upon the state of the art. The traditional source resonator on the transmitter side is equipped with an additional resonator with a resonance frequency that is tuned substantially higher than the magnetic field excitation frequency. This additional resonator enhances the magnetic dipole moment and the effective permeability of the power transmitter, owing to a phenomenon known as the strong paramagnetic response. Both theoretical calculations and experimental results show increased PTE due to amplification of the effective permeability. In measurements, the PTE was improved from 57.8% to 64.2% at the nominal distance of 15 cm when the effective permeability was 2.6. The power delivered to load was also improved significantly, with the same 10 V excitation voltage, from 0.38 to 5.26 W.

400-GHz wireless transmission of 60-Gb/s nyquist-QPSK signals using UTC-PD and heterodyne mixer

DEFF Research Database (Denmark)

Yu, Xianbin; Asif, Rameez; Piels, Molly

2016-01-01

We experimentally demonstrate an optical network compatible high-speed optoelectronics THz wireless transmission system operating at 400-GHz band. In the experiment, optical Nyquist quadrature phase-shift keying signals in a 12.5-GHz ultradense wavelength-division multiplexing grid is converted...... to the THz wireless radiation by photomixing in an antenna integrated unitravelling photodiode. The photomixing is transparent to optical modulation formats. We also demonstrate in the experiment the scalability of our system by applying single to four channels, as well as mixed three channels. Wireless...... transmission of a capacity of 60 Gb/s for four channels (15 Gb/s per channel) at 400-GHz band is successfully achieved, which pushes the data rates enabled by optoelectronics approach beyond the envelope in the frequency range above 300 GHz. Besides those, this study also validates the potential of bridging...

An RFID-Based Closed-Loop Wireless Power Transmission System for Biomedical Applications.

Science.gov (United States)

Kiani, Mehdi; Ghovanloo, Maysam

2010-04-01

This brief presents a standalone closed-loop wireless power transmission system that is built around a commercial off-the-shelf (COTS) radio-frequency identification (RFID) reader (TRF7960) operating at 13.56 MHz. It can be used for inductively powering implantable biomedical devices in a closed loop. Any changes in the distance and misalignment between transmitter and receiver coils in near-field wireless power transmission can cause a significant change in the received power, which can cause either a malfunction or excessive heat dissipation. RFID circuits are often used in an open loop. However, their back telemetry capability can be utilized to stabilize the received voltage on the implant. Our measurements showed that the delivered power to the transponder was maintained at 11.2 mW over a range of 0.5 to 2 cm, while the transmitter power consumption changed from 78 mW to 1.1 W. The closed-loop system can also oppose voltage variations as a result of sudden changes in the load current.

LSコイルを用いたWireless Power Transmission

OpenAIRE

吉川, 隆; 更谷, 翔太

2014-01-01

The wireless power transmission is widely studied for many kinds of application, for example, power supply for cell phone or power source of EV. The supplying power of those applications is always over mW. But it is impossible to transmit for longer distance under the index of regulation of protection from radiofrequency electromagnetic field. Then many of such applications are considered with restriction of narrow area. Then we have surveyed low power demanding application the suitable appl...

Wireless (Power Transfer Transmission of Electrical Energy (Electricity Intended for Consumer Purposes up to 50 W

Directory of Open Access Journals (Sweden)

Marek Piri

2016-01-01

Full Text Available This project deals with Power Semiconductor Systems PSS for wireless transmission of electricity to the power of 50~W with regard to the distance and transmission efficiency. We decided to use electromagnetic resonance for electrical energy transmission. For experimental verification, we have wound two coils of identical dimensions. At a given power transmission solutions, we obtain the highest efficiency η = 70% at a distance of 5 cm, where the transmitted power was 48 W.

Optical-wireless-optical full link for polarization multiplexing quadrature amplitude/phase modulation signal transmission.

Science.gov (United States)

Li, Xinying; Yu, Jianjun; Chi, Nan; Zhang, Junwen

2013-11-15

We propose and experimentally demonstrate an optical wireless integration system at the Q-band, in which up to 40 Gb/s polarization multiplexing multilevel quadrature amplitude/phase modulation (PM-QAM) signal can be first transmitted over 20 km single-mode fiber-28 (SMF-28), then delivered over a 2 m 2 × 2 multiple-input multiple-output wireless link, and finally transmitted over another 20 km SMF-28. The PM-QAM modulated wireless millimeter-wave (mm-wave) signal at 40 GHz is generated based on the remote heterodyning technique, and demodulated by the radio-frequency transparent photonic technique based on homodyne coherent detection and baseband digital signal processing. The classic constant modulus algorithm equalization is used at the receiver to realize polarization demultiplexing of the PM-QAM signal. For the first time, to the best of our knowledge, we realize the conversion of the PM-QAM modulated wireless mm-wave signal to the optical signal as well as 20 km fiber transmission of the converted optical signal.

38.2-Gb/s Optical-Wireless Transmission in 75-110 GHz Based on Electrical OFDM with Optical Comb Expansion

DEFF Research Database (Denmark)

Deng, Lei; Pang, Xiaodan; Beltrán, Marta

2012-01-01

We demonstrate scalable optical comb- and heterodyning-based generation, optical and 1.3-m wireless transmission, and electrical heterodyne detection of multiband OFDM up to 38.2 Gb/s occupying 14.4-GHz RF bandwidth, for high-capacity optical-wireless links in 75-110 GHz....

Modeling and Characteristic Analysis of Wireless Ultrasonic Vibration Energy Transmission Channels through Planar and Curved Metal Barriers

Directory of Open Access Journals (Sweden)

DingXin Yang

2018-01-01

Full Text Available Wireless ultrasonic vibration energy transmission systems through metal barriers based on piezoelectric transducers have drawn a lot of focus due to the advantage of nonpenetration of the barriers, thus maintaining the integrity of sealed structures. It is meaningful to investigate appropriate modeling methods and to characterize such wireless ultrasonic energy transmission channels with different geometric shapes. In this paper, equivalent circuit modeling and finite element modeling methods are applied to the planar metal barrier channel, and a 3-dimensional finite element modeling method is applied to the cylindrical metallic barrier channel. Meanwhile, the experimental setup is established and measurements are carried out to validate the effectiveness of the corresponding modeling methods. The results show that Leach’s equivalent circuit modeling method and finite element modeling method are nearly similarly effective in characterizing the planar metal barrier channel. But for a cylindrical metal barrier, only the three-dimensional finite element modeling method is effective. Furthermore, we found that, for the planar barrier, the effect of standing waves on the efficiency of wireless energy transmission is dominated. But for the curved barrier, only the resonant phenomenon of the piezoelectric transducer exists.

Feasibility of Frequency-Modulated Wireless Transmission for a Multi-Purpose MEMS-Based Accelerometer

Directory of Open Access Journals (Sweden)

Alessandro Sabato

2014-09-01

Full Text Available Recent advances in the Micro Electro-Mechanical System (MEMS technology have made wireless MEMS accelerometers an attractive tool for Structural Health Monitoring (SHM of civil engineering structures. To date, sensors’ low sensitivity and accuracy—especially at very low frequencies—have imposed serious limitations for their application in monitoring large-sized structures. Conventionally, the MEMS sensor’s analog signals are converted to digital signals before radio-frequency (RF wireless transmission. The conversion can cause a low sensitivity to the important low-frequency and low-amplitude signals. To overcome this difficulty, the authors have developed a MEMS accelerometer system, which converts the sensor output voltage to a frequency-modulated signal before RF transmission. This is achieved by using a Voltage to Frequency Conversion (V/F instead of the conventional Analog to Digital Conversion (ADC. In this paper, a prototype MEMS accelerometer system is presented, which consists of a transmitter and receiver circuit boards. The former is equipped with a MEMS accelerometer, a V/F converter and a wireless RF transmitter, while the latter contains an RF receiver and a F/V converter for demodulating the signal. The efficacy of the MEMS accelerometer system in measuring low-frequency and low-amplitude dynamic responses is demonstrated through extensive laboratory tests and experiments on a flow-loop pipeline.

[Mobile phone-computer wireless interactive graphics transmission technology and its medical application].

Science.gov (United States)

Huang, Shuo; Liu, Jing

2010-05-01

Application of clinical digital medical imaging has raised many tough issues to tackle, such as data storage, management, and information sharing. Here we investigated a mobile phone based medical image management system which is capable of achieving personal medical imaging information storage, management and comprehensive health information analysis. The technologies related to the management system spanning the wireless transmission technology, the technical capabilities of phone in mobile health care and management of mobile medical database were discussed. Taking medical infrared images transmission between phone and computer as an example, the working principle of the present system was demonstrated.

SVANET: A smart vehicular ad hoc network for efficient data transmission with wireless sensors.

Science.gov (United States)

Sahoo, Prasan Kumar; Chiang, Ming-Jer; Wu, Shih-Lin

2014-11-25

Wireless sensors can sense any event, such as accidents, as well as icy roads, and can forward the rescue/warning messages through intermediate vehicles for any necessary help. In this paper, we propose a smart vehicular ad hoc network (SVANET) architecture that uses wireless sensors to detect events and vehicles to transmit the safety and non-safety messages efficiently by using different service channels and one control channel with different priorities. We have developed a data transmission protocol for the vehicles in the highway, in which data can be forwarded with the help of vehicles if they are connected with each other or data can be forwarded with the help of nearby wireless sensors. Our data transmission protocol is designed to increase the driving safety, to prevent accidents and to utilize channels efficiently by adjusting the control and service channel time intervals dynamically. Besides, our protocol can transmit information to vehicles in advance, so that drivers can decide an alternate route in case of traffic congestion. For various data sharing, we design a method that can select a few leader nodes among vehicles running along a highway to broadcast data efficiently. Simulation results show that our protocol can outperform the existing standard in terms of the end to end packet delivery ratio and latency.

A multi-channel low-power system-on-chip for single-unit recording and narrowband wireless transmission of neural signal.

Science.gov (United States)

Bonfanti, A; Ceravolo, M; Zambra, G; Gusmeroli, R; Spinelli, A S; Lacaita, A L; Angotzi, G N; Baranauskas, G; Fadiga, L

2010-01-01

This paper reports a multi-channel neural recording system-on-chip (SoC) with digital data compression and wireless telemetry. The circuit consists of a 16 amplifiers, an analog time division multiplexer, an 8-bit SAR AD converter, a digital signal processor (DSP) and a wireless narrowband 400-MHz binary FSK transmitter. Even though only 16 amplifiers are present in our current die version, the whole system is designed to work with 64 channels demonstrating the feasibility of a digital processing and narrowband wireless transmission of 64 neural recording channels. A digital data compression, based on the detection of action potentials and storage of correspondent waveforms, allows the use of a 1.25-Mbit/s binary FSK wireless transmission. This moderate bit-rate and a low frequency deviation, Manchester-coded modulation are crucial for exploiting a narrowband wireless link and an efficient embeddable antenna. The chip is realized in a 0.35- εm CMOS process with a power consumption of 105 εW per channel (269 εW per channel with an extended transmission range of 4 m) and an area of 3.1 × 2.7 mm(2). The transmitted signal is captured by a digital TV tuner and demodulated by a wideband phase-locked loop (PLL), and then sent to a PC via an FPGA module. The system has been tested for electrical specifications and its functionality verified in in-vivo neural recording experiments.

DRDT: distributed and reliable data transmission with cooperative nodes for lossy wireless sensor networks.

Science.gov (United States)

Seo, Jaewan; Kim, Moonseong; Hur, In; Choi, Wook; Choo, Hyunseung

2010-01-01

Recent studies have shown that in realistic wireless sensor network environments links are extremely unreliable. To recover from corrupted packets, most routing schemes with an assumption of ideal radio environments use a retransmission mechanism, which may cause unnecessary retransmissions. Therefore, guaranteeing energy-efficient reliable data transmission is a fundamental routing issue in wireless sensor networks. However, it is not encouraged to propose a new reliable routing scheme in the sense that every existing routing scheme cannot be replaced with the new one. This paper proposes a Distributed and Reliable Data Transmission (DRDT) scheme with a goal to efficiently guarantee reliable data transmission. In particular, this is based on a pluggable modular approach so that it can be extended to existing routing schemes. DRDT offers reliable data transmission using neighbor nodes, i.e., helper nodes. A helper node is selected among the neighbor nodes of the receiver node which overhear the data packet in a distributed manner. DRDT effectively reduces the number of retransmissions by delegating the retransmission task from the sender node to the helper node that has higher link quality to the receiver node when the data packet reception fails due to the low link quality between the sender and the receiver nodes. Comprehensive simulation results show that DRDT improves end-to-end transmission cost by up to about 45% and reduces its delay by about 40% compared to existing schemes.

DRDT: Distributed and Reliable Data Transmission with Cooperative Nodes for LossyWireless Sensor Networks

Directory of Open Access Journals (Sweden)

Jaewan Seo

2010-03-01

Full Text Available Recent studies have shown that in realistic wireless sensor network environments links are extremely unreliable. To recover from corrupted packets, most routing schemes with an assumption of ideal radio environments use a retransmission mechanism, which may cause unnecessary retransmissions. Therefore, guaranteeing energy-efficient reliable data transmission is a fundamental routing issue in wireless sensor networks. However, it is not encouraged to propose a new reliable routing scheme in the sense that every existing routing scheme cannot be replaced with the new one. This paper proposes a Distributed and Reliable Data Transmission (DRDT scheme with a goal to efficiently guarantee reliable data transmission. In particular, this is based on a pluggable modular approach so that it can be extended to existing routing schemes. DRDT offers reliable data transmission using neighbor nodes, i.e., helper nodes. A helper node is selected among the neighbor nodes of the receiver node which overhear the data packet in a distributed manner. DRDT effectively reduces the number of retransmissions by delegating the retransmission task from the sender node to the helper node that has higher link quality to the receiver node when the data packet reception fails due to the low link quality between the sender and the receiver nodes. Comprehensive simulation results show that DRDT improves end-to-end transmission cost by up to about 45% and reduces its delay by about 40% compared to existing schemes.

Low-current solutions for wireless point-to-point sensor data transmission for long-term applications; Stromsparende Loesungen fuer drahtlose Punkt-zu-Punkt-Sensordatenuebertragung fuer langjaehrigen Betrieb

Energy Technology Data Exchange (ETDEWEB)

Milosiu, H. [Fraunhofer-Institut fuer Integrierte Schaltungen IIS, Erlangen (Germany)

2008-07-01

Choosing wireless standard such as Bluetooth or Zigbee, the customer can find numerous low-cost chip sets. In particular applications proprietary solutions are superior to wireless standard solutions, especially for transmission of small data amounts from point to point. The complex transmission protocol of a wireless standard forms a inflexible precondition for the user and may exclude the choice of a wireless standard. In addition, a relatively high energy consumption disables battery-operated low-maintenance applications. Fraunhofer Institute for Integrated Circuits IIS in Erlangen now offers a solution to that problem. This article would like to show the benefits of low-current proprietary wireless systems. An implementation of a lowcurrent wireless system using BiCMOS technology for wireless sensor networks is presented. (orig.)

Impulse radio ultra wideband wireless transmission of dopamine concentration levels recorded by fast-scan cyclic voltammetry.

Science.gov (United States)

Ebrazeh, Ali; Bozorgzadeh, Bardia; Mohseni, Pedram

2015-01-01

This paper demonstrates the feasibility of utilizing impulse radio ultra wideband (IR-UWB) signaling technique for reliable, wireless transmission of dopamine concentration levels recorded by fast-scan cyclic voltammetry (FSCV) at a carbon-fiber microelectrode (CFM) to address the problem of elevated data rates in high-channel-count neurochemical monitoring. Utilizing an FSCV-sensing chip fabricated in AMS 0.35μm 2P/4M CMOS, a 3-5-GHz, IR-UWB transceiver (TRX) chip fabricated in TSMC 90nm 1P/9M RF CMOS, and two off-chip, miniature, UWB antennae, wireless transfer of pseudo-random binary sequence (PRBS) data at 50Mbps over a distance of wireless transmission of dopamine concentration levels prerecorded with FSCV at a CFM during flow injection analysis (FIA) is also demonstrated with transmitter (TX) power dissipation of only ~4.4μW from 1.2V, representing two orders of magnitude reduction in TX power consumption compared to that of a conventional frequency-shift-keyed (FSK) link operating at ~433MHz.

Grassroots Technological Resistance: The People's Power Project and the Impossible Dream of Wireless Transmission of Energy.

Science.gov (United States)

Schmidt, Pete

2017-09-01

In 1972, the Minnesota United Power Association (UPA) teamed up with the Minnesota Cooperative Power Association (CPA) to initiate an electrification project designed to bring power from North Dakota to the Twin Cities area. A significant backlash and protest began once farmers across the state became aware of the plan and the potential impending land seizure. In the midst of these actions, one group sought to create an alternative to the power line transmission system by designing a system of wireless energy transmission based on the plans of Nikola Tesla. This self-funded conglomeration of farmers and amateur researchers formed the People's Power Project (PPP) and set about building Tesla's system for the wireless transmission of energy. Using archival documents, this paper recounts this episode and argues that, in this case, the potential for successful grassroots action was derailed by the influence of longstanding myths about Tesla and his devices. Copyright © 2017 Elsevier Ltd. All rights reserved.

Screening of young competitive athletes for the prevention of sudden cardiac death with a wireless electrocardiographic transmission device: a pilot study.

Science.gov (United States)

Cho, Jae Hyung; Selen, Mats A; Kocheril, Abraham G

2015-08-11

The 12-lead electrocardiographic screening for the prevention of sudden cardiac death in young competitive athletes is not cost-effective and thus not routinely recommended. We investigate whether a less expensive wireless electrocardiographic transmission device can be used to screen for the prevention of sudden cardiac death in this population. During pre-participation screening, twenty college football players underwent two electrocardiograms: a conventional 12-lead electrocardiogram and a wireless 9-lead electrocardiogram. We compared several electrocardiographic parameters (QRS duration, left ventricular hypertrophy using the Cornell voltage criteria and the Sokolow-Lyon criteria, ST deviation and corrected QT interval) to determine the correlation. The QRS duration, left ventricular hypertrophy using the Cornell voltage criteria and the Sokolow-Lyon criteria and corrected QT interval exhibited significant correlation between the two types of electrocardiograms (correlation coefficient 0.878, 0.630, 0.770 and 0.847, respectively with P values of 0.01, 0.003, 0.01 and 0.01, respectively). ST deviation in V1 was weakly correlated between the two types of electrocardiograms without statistical significance (correlation coefficient 0.360 with a P value of 0.119). Our newly developed wireless 9-lead electrocardiogram demonstrated significant correlations with a conventional 12-lead electrocardiogram in terms of QRS duration, left ventricular hypertrophy and corrected QT interval.

Novel technical solutions for wireless ECG transmission & analysis in the age of the internet cloud.

Science.gov (United States)

Al-Zaiti, Salah S; Shusterman, Vladimir; Carey, Mary G

2013-01-01

Current guidelines recommend early reperfusion therapy for ST-elevation myocardial infarction (STEMI) within 90 min of first medical encounter. Telecardiology entails the use of advanced communication technologies to transmit the prehospital 12-lead electrocardiogram (ECG) to offsite cardiologists for early triage to the cath lab; which has been shown to dramatically reduce door-to-balloon time and total mortality. However, hospitals often find adopting ECG transmission technologies very challenging. The current review identifies seven major technical challenges of prehospital ECG transmission, including: paramedics inconvenience and transport delay; signal noise and interpretation errors; equipment malfunction and transmission failure; reliability of mobile phone networks; lack of compliance with the standards of digital ECG formats; poor integration with electronic medical records; and costly hardware and software pre-requisite installation. Current and potential solutions to address each of these technical challenges are discussed in details and include: automated ECG transmission protocols; annotatable waveform-based ECGs; optimal routing solutions; and the use of cloud computing systems rather than vendor-specific processing stations. Nevertheless, strategies to monitor transmission effectiveness and patient outcomes are essential to sustain initial gains of implementing ECG transmission technologies. © 2013.

A medical-grade wireless architecture for remote electrocardiography.

Science.gov (United States)

Kang, Kyungtae; Park, Kyung-Joon; Song, Jae-Jin; Yoon, Chang-Hwan; Sha, Lui

2011-03-01

In telecardiology, electrocardiogram (ECG) signals from a patient are acquired by sensors and transmitted in real time to medical personnel across a wireless network. The use of IEEE 802.11 wireless LANs (WLANs), which are already deployed in many hospitals, can provide ubiquitous connectivity and thus allow cardiology patients greater mobility. However, engineering issues, including the error-prone nature of wireless channels and the unpredictable delay and jitter due to the nondeterministic nature of access to the wireless medium, need to be addressed before telecardiology can be safely realized. We propose a medical-grade WLAN architecture for remote ECG monitoring, which employs the point-coordination function (PCF) for medium access control and Reed-Solomon coding for error control. Realistic simulations with uncompressed two-lead ECG data from the MIT-BIH arrhythmia database demonstrate reliable wireless ECG monitoring; the reliability of ECG transmission exceeds 99.99% with the initial buffering delay of only 2.4 s.

Optimization of high-definition video coding and hybrid fiber-wireless transmission in the 60 GHz band

DEFF Research Database (Denmark)

Lebedev, Alexander; Pham, Tien Thang; Beltrán, Marta

2011-01-01

The paper addresses the problem of distribution of highdefinition video over fiber-wireless networks. The physical layer architecture with the low complexity envelope detection solution is investigated. We present both experimental studies and simulation of high quality high-definition compressed...... video transmission over 60 GHz fiberwireless link. Using advanced video coding we satisfy low complexity and low delay constraints, meanwhile preserving the superb video quality after significantly extended wireless distance. © 2011 Optical Society of America....

An adaptive secret key-directed cryptographic scheme for secure transmission in wireless sensor networks

International Nuclear Information System (INIS)

Muhammad, K.; Jan, Z.; Khan, Z

2015-01-01

Wireless Sensor Networks (WSNs) are memory and bandwidth limited networks whose main goals are to maximize the network lifetime and minimize the energy consumption and transmission cost. To achieve these goals, different techniques of compression and clustering have been used. However, security is an open and major issue in WSNs for which different approaches are used, both in centralized and distributed WSNs' environments. This paper presents an adaptive cryptographic scheme for secure transmission of various sensitive parameters, sensed by wireless sensors to the fusion center for further processing in WSNs such as military networks. The proposed method encrypts the sensitive captured data of sensor nodes using various encryption procedures (bitxor operation, bits shuffling, and secret key based encryption) and then sends it to the fusion center. At the fusion center, the received encrypted data is decrypted for taking further necessary actions. The experimental results with complexity analysis, validate the effectiveness and feasibility of the proposed method in terms of security in WSNs. (author)

Simulation Analysis of Wireless Power Transmission System for Biomedical Applications

Science.gov (United States)

Yang, Zhao; Wei, Zhiqiang; Chi, Haokun; Yin, Bo; Cong, Yanping

2018-03-01

In recent years, more and more implantable medical devices have been used in the medical field. Some of these devices, such as brain pacemakers, require long-term power support. The WPT(wireless power transmission) technology which is more convenient and economical than replacing the battery by surgery, has become the first choice of many patients. In this paper, we design a WPT system that can be used in implantable medical devices, simulate the transmission efficiency of the system in the air and in the head model, and simulate the SAR value when the system working in the head model. The results show that when implantation depth of the secondary coil is 3 mm, the efficiency of the system can reach 45%, and the maximum average SAR value is 2.19 W / kg, slightly higher than the standard of IEEE.

[A wireless power transmission system for capsule endoscope].

Science.gov (United States)

Xin, Wenhui; Yan, Guozheng; Wang, Wenxing

2010-06-01

In order to deliver power to the capsule endoscope, whose position and orientation are always changing when traveling along the alimentary tract, a wireless power transmission system based on electromagnetic coupling was proposed. The system is composed of Helmholtz transmitting coil and three-dimensional receiving coil. Helmholtz coil outside the body generates a uniform magnetic field covering the whole alimentary tract; three-dimensional coil inside retrieves stable power regardless of its position and orientation. The transmitter and receiver were designed and implemented, and the experiments validated the feasibility of the system. The results show that at least 320 mW of usable power can be transmitted to capsule endoscope when its position and orientation are changing at random and the transmitting power is 25W.

A novel power efficient location-based cooperative routing with transmission power-upper-limit for wireless sensor networks.

Science.gov (United States)

Shi, Juanfei; Calveras, Anna; Cheng, Ye; Liu, Kai

2013-05-15

The extensive usage of wireless sensor networks (WSNs) has led to the development of many power- and energy-efficient routing protocols. Cooperative routing in WSNs can improve performance in these types of networks. In this paper we discuss the existing proposals and we propose a routing algorithm for wireless sensor networks called Power Efficient Location-based Cooperative Routing with Transmission Power-upper-limit (PELCR-TP). The algorithm is based on the principle of minimum link power and aims to take advantage of nodes cooperation to make the link work well in WSNs with a low transmission power. In the proposed scheme, with a determined transmission power upper limit, nodes find the most appropriate next nodes and single-relay nodes with the proposed algorithm. Moreover, this proposal subtly avoids non-working nodes, because we add a Bad nodes Avoidance Strategy (BAS). Simulation results show that the proposed algorithm with BAS can significantly improve the performance in reducing the overall link power, enhancing the transmission success rate and decreasing the retransmission rate.

A Novel Power Efficient Location-Based Cooperative Routing with Transmission Power-Upper-Limit for Wireless Sensor Networks

Science.gov (United States)

Shi, Juanfei; Calveras, Anna; Cheng, Ye; Liu, Kai

2013-01-01

The extensive usage of wireless sensor networks (WSNs) has led to the development of many power- and energy-efficient routing protocols. Cooperative routing in WSNs can improve performance in these types of networks. In this paper we discuss the existing proposals and we propose a routing algorithm for wireless sensor networks called Power Efficient Location-based Cooperative Routing with Transmission Power-upper-limit (PELCR-TP). The algorithm is based on the principle of minimum link power and aims to take advantage of nodes cooperation to make the link work well in WSNs with a low transmission power. In the proposed scheme, with a determined transmission power upper limit, nodes find the most appropriate next nodes and single-relay nodes with the proposed algorithm. Moreover, this proposal subtly avoids non-working nodes, because we add a Bad nodes Avoidance Strategy (BAS). Simulation results show that the proposed algorithm with BAS can significantly improve the performance in reducing the overall link power, enhancing the transmission success rate and decreasing the retransmission rate. PMID:23676625

SVANET: A Smart Vehicular Ad Hoc Network for Efficient Data Transmission with Wireless Sensors

Directory of Open Access Journals (Sweden)

Prasan Kumar Sahoo

2014-11-01

Full Text Available Wireless sensors can sense any event, such as accidents, as well as icy roads, and can forward the rescue/warning messages through intermediate vehicles for any necessary help. In this paper, we propose a smart vehicular ad hoc network (SVANET architecture that uses wireless sensors to detect events and vehicles to transmit the safety and non-safety messages efficiently by using different service channels and one control channel with different priorities. We have developed a data transmission protocol for the vehicles in the highway, in which data can be forwarded with the help of vehicles if they are connected with each other or data can be forwarded with the help of nearby wireless sensors. Our data transmission protocol is designed to increase the driving safety, to prevent accidents and to utilize channels efficiently by adjusting the control and service channel time intervals dynamically. Besides, our protocol can transmit information to vehicles in advance, so that drivers can decide an alternate route in case of traffic congestion. For various data sharing, we design a method that can select a few leader nodes among vehicles running along a highway to broadcast data efficiently. Simulation results show that our protocol can outperform the existing standard in terms of the end to end packet delivery ratio and latency.

A transmission power optimization with a minimum node degree for energy-efficient wireless sensor networks with full-reachability.

Science.gov (United States)

Chen, Yi-Ting; Horng, Mong-Fong; Lo, Chih-Cheng; Chu, Shu-Chuan; Pan, Jeng-Shyang; Liao, Bin-Yih

2013-03-20

Transmission power optimization is the most significant factor in prolonging the lifetime and maintaining the connection quality of wireless sensor networks. Un-optimized transmission power of nodes either interferes with or fails to link neighboring nodes. The optimization of transmission power depends on the expected node degree and node distribution. In this study, an optimization approach to an energy-efficient and full reachability wireless sensor network is proposed. In the proposed approach, an adjustment model of the transmission range with a minimum node degree is proposed that focuses on topology control and optimization of the transmission range according to node degree and node density. The model adjusts the tradeoff between energy efficiency and full reachability to obtain an ideal transmission range. In addition, connectivity and reachability are used as performance indices to evaluate the connection quality of a network. The two indices are compared to demonstrate the practicability of framework through simulation results. Furthermore, the relationship between the indices under the conditions of various node degrees is analyzed to generalize the characteristics of node densities. The research results on the reliability and feasibility of the proposed approach will benefit the future real deployments.

A Transmission Power Optimization with a Minimum Node Degree for Energy-Efficient Wireless Sensor Networks with Full-Reachability

Science.gov (United States)

Chen, Yi-Ting; Horng, Mong-Fong; Lo, Chih-Cheng; Chu, Shu-Chuan; Pan, Jeng-Shyang; Liao, Bin-Yih

2013-01-01

Transmission power optimization is the most significant factor in prolonging the lifetime and maintaining the connection quality of wireless sensor networks. Un-optimized transmission power of nodes either interferes with or fails to link neighboring nodes. The optimization of transmission power depends on the expected node degree and node distribution. In this study, an optimization approach to an energy-efficient and full reachability wireless sensor network is proposed. In the proposed approach, an adjustment model of the transmission range with a minimum node degree is proposed that focuses on topology control and optimization of the transmission range according to node degree and node density. The model adjusts the tradeoff between energy efficiency and full reachability to obtain an ideal transmission range. In addition, connectivity and reachability are used as performance indices to evaluate the connection quality of a network. The two indices are compared to demonstrate the practicability of framework through simulation results. Furthermore, the relationship between the indices under the conditions of various node degrees is analyzed to generalize the characteristics of node densities. The research results on the reliability and feasibility of the proposed approach will benefit the future real deployments. PMID:23519351

A New Energy-Efficient Data Transmission Scheme Based on DSC and Virtual MIMO for Wireless Sensor Network

OpenAIRE

Li, Na; Zhang, Liwen; Li, Bing

2015-01-01

Energy efficiency in wireless sensor network (WSN) is one of the primary performance parameters. For improving the energy efficiency of WSN, we introduce distributed source coding (DSC) and virtual multiple-input multiple-output (MIMO) into wireless sensor network and then propose a new data transmission scheme called DSC-MIMO. DSC-MIMO compresses the source data using distributed source coding before transmitting, which is different from the existing communication schemes. Data compression c...

Cross-layer Energy Optimization Under Image Quality Constraints for Wireless Image Transmissions.

Science.gov (United States)

Yang, Na; Demirkol, Ilker; Heinzelman, Wendi

2012-01-01

Wireless image transmission is critical in many applications, such as surveillance and environment monitoring. In order to make the best use of the limited energy of the battery-operated cameras, while satisfying the application-level image quality constraints, cross-layer design is critical. In this paper, we develop an image transmission model that allows the application layer (e.g., the user) to specify an image quality constraint, and optimizes the lower layer parameters of transmit power and packet length, to minimize the energy dissipation in image transmission over a given distance. The effectiveness of this approach is evaluated by applying the proposed energy optimization to a reference ZigBee system and a WiFi system, and also by comparing to an energy optimization study that does not consider any image quality constraint. Evaluations show that our scheme outperforms the default settings of the investigated commercial devices and saves a significant amount of energy at middle-to-large transmission distances.

Wireless power transmission for biomedical implants: The role of near-zero threshold CMOS rectifiers.

Science.gov (United States)

Mohammadi, Ali; Redoute, Jean-Michel; Yuce, Mehmet R

2015-01-01

Biomedical implants require an electronic power conditioning circuitry to provide a stable electrical power supply. The efficiency of wireless power transmission is strongly dependent on the power conditioning circuitry specifically the rectifier. A cross-connected CMOS bridge rectifier is implemented to demonstrate the impact of thresholds of rectifiers on wireless power transfer. The performance of the proposed rectifier is experimentally compared with a conventional Schottky diode full wave rectifier over 9 cm distance of air and tissue medium between the transmitter and receiver. The output voltage generated by the CMOS rectifier across a 1 KΩ resistive load is around twice as much as the Schottky rectifier.

Monitoring in the post-closure phase. Development of wireless techniques for data transmission from the repository to the surface

International Nuclear Information System (INIS)

Schroeder, Thomas J.; Rosca-Bocancea, Ecaterina; Hart, Jaap

2015-01-01

When the in-situ monitoring in a geological disposal facility is continued during the post-closure phase, monitoring data need to be transmitted wirelessly from the repository to the surface. Wireless data transmission is used today in many applications, but the large attenuation by the geologic medium between the disposal facility and the surface makes the application of high-frequency based techniques impractical. As part of the EURATOM FP-7 project MoDeRn (Monitoring Developments for safe Repository operation and staged closure), NRG has investigated the feasibility of wireless data transmission through an argillaceous host rock (Boom Clay), making use of low frequency magnetic fields. The main focus of the contribution was to analyze and optimize the energy efficiency of this technique. Therefore, a mathematical model description has been developed that allows to estimate the expected signal strength on the earth's surface on basis of the most relevant characteristics of transmitter, receiver and transmission path. The model is used to analyze the complex interactions of different system parameters, and is applied to design an optimized set-up for through-the-earth data transmission and to estimate minimum energy demands for signal transmission. To demonstrate the potentials of this technique, experiments were performed in the 225 m deep underground research facility HADES in Mol, Belgium. Signal propagation and attenuation by the geologic medium between the HADES and the surface has been measured, and the site-specific magnetic background noise at the surface in Mol has been characterized. Based on the results, optimum conditions for signal transmission have been derived and data transmission experiments have been performed. Results show that despite large local interferences on the surface in Mol, wireless data transmission through 225 m of a geological medium is possible. Data transmission rates up to 100 bit/s has been successfully tested. The

Monitoring in the post-closure phase. Development of wireless techniques for data transmission from the repository to the surface

Energy Technology Data Exchange (ETDEWEB)

Schroeder, Thomas J.; Rosca-Bocancea, Ecaterina; Hart, Jaap [Nuclear Research and Consultancy Group (NRG), Petten (Netherlands)

2015-07-01

When the in-situ monitoring in a geological disposal facility is continued during the post-closure phase, monitoring data need to be transmitted wirelessly from the repository to the surface. Wireless data transmission is used today in many applications, but the large attenuation by the geologic medium between the disposal facility and the surface makes the application of high-frequency based techniques impractical. As part of the EURATOM FP-7 project MoDeRn (Monitoring Developments for safe Repository operation and staged closure), NRG has investigated the feasibility of wireless data transmission through an argillaceous host rock (Boom Clay), making use of low frequency magnetic fields. The main focus of the contribution was to analyze and optimize the energy efficiency of this technique. Therefore, a mathematical model description has been developed that allows to estimate the expected signal strength on the earth's surface on basis of the most relevant characteristics of transmitter, receiver and transmission path. The model is used to analyze the complex interactions of different system parameters, and is applied to design an optimized set-up for through-the-earth data transmission and to estimate minimum energy demands for signal transmission. To demonstrate the potentials of this technique, experiments were performed in the 225 m deep underground research facility HADES in Mol, Belgium. Signal propagation and attenuation by the geologic medium between the HADES and the surface has been measured, and the site-specific magnetic background noise at the surface in Mol has been characterized. Based on the results, optimum conditions for signal transmission have been derived and data transmission experiments have been performed. Results show that despite large local interferences on the surface in Mol, wireless data transmission through 225 m of a geological medium is possible. Data transmission rates up to 100 bit/s has been successfully tested. The

An optimized compression algorithm for real-time ECG data transmission in wireless network of medical information systems.

Science.gov (United States)

Cho, Gyoun-Yon; Lee, Seo-Joon; Lee, Tae-Ro

2015-01-01

Recent medical information systems are striving towards real-time monitoring models to care patients anytime and anywhere through ECG signals. However, there are several limitations such as data distortion and limited bandwidth in wireless communications. In order to overcome such limitations, this research focuses on compression. Few researches have been made to develop a specialized compression algorithm for ECG data transmission in real-time monitoring wireless network. Not only that, recent researches' algorithm is not appropriate for ECG signals. Therefore this paper presents a more developed algorithm EDLZW for efficient ECG data transmission. Results actually showed that the EDLZW compression ratio was 8.66, which was a performance that was 4 times better than any other recent compression method widely used today.

Study on explosion field temperature testing system based on wireless data transmission

International Nuclear Information System (INIS)

Wang Xinling; Sun Yunqiang

2011-01-01

The accurate measurement of the transient temperature value produced by explosive blasting may provide the basis for distinguishing the types of the explosive, the power contrast of the explosive and the performance evaluation in the weapons research process. To solve the problems of the Universal Test System emplaced inconveniently and the stored testing system need to be recycled, it has designed the explosion field application in wireless sensor system of temperature measurement. The system based on PIC16F877A micro controller, CPLD complex programmable logic devices and nRF24L01 wireless transmission chip sensor. The system adopts the Tungsten-Rhenium Thermocouple as the temperature sensor, DS600 temperature sensor for cold temperature compensation. This system has arrangement convenient, high-speed data acquisition, trigger and working parameters of adjustable characteristics, has been successfully applied in a test system. (authors)

How coupling affects closely packed rectenna arrays used for wireless power transmission

Science.gov (United States)

Walls, Deidra; Choi, Sang H.; Yoon, Hargsoon; Geddis, Demetris; Song, Kyo D.

2017-04-01

The development of power transmission by microwave beam power harvesting attracts manufactures for use of wireless power transmission. Optimizing maximum conversion efficiency is affected by many design parameters, and has been mainly focused previously. Combining several rectennas in one array potentially aides in the amount of microwave energy that can be harvested for energy conversion. Closely packed rectenna arrays is the result of the demand to minimize size and weight for flexibility. This paper specifically focuses on the coupling effects on power; mutual coupling, comparing sparameters and gain total while varying effective parameters. This paper investigates how coupling between each dipole positively and negatively affects the microwave energy, harvesting, and the design limitations.

Magnetic shielding structure optimization design for wireless power transmission coil

Science.gov (United States)

Dai, Zhongyu; Wang, Junhua; Long, Mengjiao; Huang, Hong; Sun, Mingui

2017-09-01

In order to improve the performance of the wireless power transmission (WPT) system, a novel design scheme with magnetic shielding structure on the WPT coil is presented in this paper. This new type of shielding structure has great advantages on magnetic flux leakage reduction and magnetic field concentration. On the basis of theoretical calculation of coil magnetic flux linkage and characteristic analysis as well as practical application feasibility consideration, a complete magnetic shielding structure was designed and the whole design procedure was represented in detail. The simulation results show that the coil with the designed shielding structure has the maximum energy transmission efficiency. Compared with the traditional shielding structure, the weight of the new design is significantly decreased by about 41%. Finally, according to the designed shielding structure, the corresponding experiment platform is built to verify the correctness and superiority of the proposed scheme.

An enhanced ionising radiation monitoring and detecting technique in radiotherapy units of hospitals using wireless sensor networks

International Nuclear Information System (INIS)

Ali, Peter

2017-01-01

In this paper, a solution of ionising radiation monitoring based on the concept of Wireless Sensor Network (WSN), is presented. Radiation dose rate measured by the sensor node is sent to the monitoring station through ZigBee wireless network operated on 2.4 GHz unlicensed Industrial Scientific Medical (ISM) band. The system is calibrated for use for ionizing radiation dose rate range of between amount of ionising radiation observed in radiotherapy unit of a hospital and 1.02 mSv/h. Power consumption of the sensor node is kept low by operating the node ZigBee radio with low duty cycle: i.e. by keeping the radio awake only during data transmission/reception. Two ATmega8 microcontrollers, one each for sensor node and the monitoring station, are programmed to perform interfacing, data processing, and control functions. The system range of coverage is 124m for outdoor (line of site) deployment and 56.8m for indoor application where 5 brick walls separated the sensor node and the monitoring station. Range of coverage of the system is extendable via the use of ZigBee router (s)

Pre-hospital treatment of acute poisonings in Oslo

Science.gov (United States)

Heyerdahl, Fridtjof; Hovda, Knut E; Bjornaas, Mari A; Nore, Anne K; Figueiredo, Jose CP; Ekeberg, Oivind; Jacobsen, Dag

2008-01-01

Background Poisoned patients are often treated in and discharged from pre-hospital health care settings. Studies of poisonings should therefore not only include hospitalized patients. Aims: To describe the acutely poisoned patients treated by ambulance personnel and in an outpatient clinic; compare patients transferred to a higher treatment level with those discharged without transfer; and study the one-week mortality after pre-hospital discharge. Methods A one-year multi-centre study with prospective inclusion of all acutely poisoned patients ≥ 16 years of age treated in ambulances, an outpatient clinic, and hospitals in Oslo. Results A total of 3757 health service contacts from 2997 poisoning episodes were recorded: 1860 were treated in ambulances, of which 15 died and 750 (40%) were discharged without transfer; 956 were treated in outpatient clinic, of which 801 (84%) were discharged without transfer; and 941 episodes were treated in hospitals. Patients discharged alive after ambulance treatment were mainly poisoned by opiates (70%), were frequently comatose (35%), had respiratory depression (37%), and many received naloxone (49%). The majority of the patients discharged from the outpatient clinic were poisoned by ethanol (55%), fewer were comatose (10%), and they rarely had respiratory depression (4%). Among the hospitalized, pharmaceutical poisonings were most common (58%), 23% were comatose, and 7% had respiratory depression. Male patients comprised 69% of the pre-hospital discharges, but only 46% of the hospitalized patients. Except for one patient, who died of a new heroin overdose two days following discharge from an ambulance, there were no deaths during the first week after the poisonings in the 90% of the pre-hospital discharged patients with known identity. Conclusion More than half of the poisoned patients treated in pre-hospital treatment settings were discharged without transfer to higher levels. These poisonings were more often caused by drug and

Pre-hospital treatment of acute poisonings in Oslo

Directory of Open Access Journals (Sweden)

Nore Anne K

2008-11-01

Full Text Available Abstract Background Poisoned patients are often treated in and discharged from pre-hospital health care settings. Studies of poisonings should therefore not only include hospitalized patients. Aims: To describe the acutely poisoned patients treated by ambulance personnel and in an outpatient clinic; compare patients transferred to a higher treatment level with those discharged without transfer; and study the one-week mortality after pre-hospital discharge. Methods A one-year multi-centre study with prospective inclusion of all acutely poisoned patients ≥ 16 years of age treated in ambulances, an outpatient clinic, and hospitals in Oslo. Results A total of 3757 health service contacts from 2997 poisoning episodes were recorded: 1860 were treated in ambulances, of which 15 died and 750 (40% were discharged without transfer; 956 were treated in outpatient clinic, of which 801 (84% were discharged without transfer; and 941 episodes were treated in hospitals. Patients discharged alive after ambulance treatment were mainly poisoned by opiates (70%, were frequently comatose (35%, had respiratory depression (37%, and many received naloxone (49%. The majority of the patients discharged from the outpatient clinic were poisoned by ethanol (55%, fewer were comatose (10%, and they rarely had respiratory depression (4%. Among the hospitalized, pharmaceutical poisonings were most common (58%, 23% were comatose, and 7% had respiratory depression. Male patients comprised 69% of the pre-hospital discharges, but only 46% of the hospitalized patients. Except for one patient, who died of a new heroin overdose two days following discharge from an ambulance, there were no deaths during the first week after the poisonings in the 90% of the pre-hospital discharged patients with known identity. Conclusion More than half of the poisoned patients treated in pre-hospital treatment settings were discharged without transfer to higher levels. These poisonings were more often

Unpowered wireless transmission of ultrasound signals

International Nuclear Information System (INIS)

Huang, H; Paramo, D; Deshmukh, S

2011-01-01

This paper presents a wireless ultrasound sensing system that uses frequency conversion to convert the ultrasound signal to a microwave signal and transmit it directly without digitization. Constructed from a few passive microwave components, the sensor is able to sense, modulate, and transmit the full waveform of ultrasound signals wirelessly without requiring any local power source. The principle of operation of the unpowered wireless ultrasound sensor is described first, and this is followed by a detailed description of the implementation of the sensor and the sensor interrogation unit using commercially available antennas and microwave components. Validation of the sensing system using an ultrasound pitch–catch system and the power analysis model of the system are also presented

A closed loop wireless power transmission system using a commercial RFID transceiver for biomedical applications.

Science.gov (United States)

Kiani, Mehdi; Ghovanloo, Maysam

2009-01-01

This paper presents a standalone closed loop wireless power transmission system that is built around a commercial off-the-shelf (COTS) radio frequency identification (RFID) transceiver (MLX90121) operating at 13.56 MHz. It can be used for inductively powering implantable biomedical devices in a closed loop fashion. Any changes in the distance and misalignment between transmitter and receiver coils in near-field wireless power transmission can cause a significant change in the received power, which can cause either malfunction or excessive heat dissipation. RFID transceivers are often used open loop. However, their back telemetry capability can be utilized to stabilize the received voltage on the implant. Our measurements showed that the delivered power to the transponder was maintained at 1.48 mW over a range of 6 to 12 cm, while the transmitter power consumption changed from 0.3 W to 1.21 W. The closed loop system can also oppose voltage variations as a result of sudden changes in load current.

Fiber-FSO/wireless convergent systems based on dual-polarization and one optical sideband transmission schemes

Science.gov (United States)

Huang, Xu-Hong; Lu, Hai-Han; Li, Chung-Yi; Wang, Yun-Chieh; Chang, Jen-Chieh; Jheng, Yu-Bo; Tsai, Wen-Shing

2018-06-01

A bidirectional fiber-free-space optical (FSO)/wireless convergent system that uses dual-polarization and one optical sideband transmission schemes for hybrid vestigial sideband (VSB)–four-level pulse amplitude modulation (PAM4)/millimeter-wave signal transmission is proposed and demonstrated. Using a dual-polarization scheme, one optical sideband that is modulated by a 56 Gb s‑1 VSB–PAM4 signal (x-polarization) and another optical sideband that is modulated by a 10 Gbps data stream (y-polarization) are separated and polarized orthogonally. One optical sideband modulated by a 10 Gbps data stream (y-polarization) is delivered to efficaciously suppress the dispersion-induced limitation due to a span of 40 km single-mode fiber (SMF) and the distortion due to the beating among multiple sidebands. The proposed bidirectional fiber-FSO/wireless convergent system is a prominent one for providing broadband integrated services, such as the Internet, telecommunication, and 5G mobile networks.

Optical true-time-delay microwave beam-steering with 1 Gb/s wireless transmission for in-building networks

NARCIS (Netherlands)

Cao, Z.; Li, F.; Boom, van den H.P.A.; Tangdiongga, E.; Koonen, A.M.J.

2013-01-01

An optical true time delay based microwave beam-steering (OTTD-MBS) scheme integrated with a radio-over-fibre system is demonstrated. Properties of 1Gb/s data wireless transmission with OTTD-MBS are studied.

Error Concealment using Data Hiding in Wireless Image Transmission

Directory of Open Access Journals (Sweden)

A. Akbari

2016-11-01

Full Text Available The transmission of image/video over unreliable medium like wireless networks generally results in receiving a damaged image/video. In this paper, a novel image error concealment scheme based on the idea of data hiding and Set Partitioning In Hierarchical Trees (SPIHT coding is investigated. In the encoder side, the coefficients of wavelet decomposed image are partitioned into “perfect trees”. The SPIHT coder is applied to encode each per-fect tree independently and generate an efficiently compressed reference code. This code is then embedded into the coefficients of another perfect tree which is located in a different place, using a robust data hiding scheme based on Quantization Index Modulation (QIM. In the decoder side, if a part of the image is lost, the algorithm extracts the embedded code for reference trees related to this part to reconstruct the lost information. Performance results show that for an error prone transmission, the proposed technique is promising to efficiently conceal the lost areas of the transmitted image.

RObust header compression (ROHC) performance for multimedia transmission over 3G/4G wireless networks

DEFF Research Database (Denmark)

Fitzek, Frank; Rein, S.; Seeling, P.

2005-01-01

Robust Header Compression (ROHC) has recently been proposed to reduce the large protocol header overhead when transmitting voice and other continuous meadi over IP based control stacks in wireless networks. In this paper we evaluate the real-time transmission of GSM encoded voice and H. 26L encod...

Three-phase receiving coil of wireless power transmission system for gastrointestinal robot

Science.gov (United States)

Jia, Z. W.; Jiang, T.; Liu, Y.

2017-11-01

Power shortage is the bottleneck for the wide application of gastrointestinal (GI) robot. Owing to the limited volume and free change of orientation of the receiving set in GI trace, the optimal of receiving set is the key point to promote the transmission efficiency of wireless power transmission system. A new type of receiving set, similar to the winding of three-phase asynchronous motor, is presented and compared with the original three-dimensional orthogonal coil. Considering the given volume and the space utilization ratio, the three-phase and the three-orthogonal ones are the parameters which are optimized and compared. Both the transmission efficiency and stability are analyzed and verified by in vitro experiments. Animal experiments show that the new one could provide at least 420 mW power in volume of Φ11 × 13mm with a uniformity of 78.3% for the GI robot.

An applicable 5.8 GHz wireless power transmission system with rough beamforming to Project Loon

Directory of Open Access Journals (Sweden)

Chang-Jun Ahn

2016-06-01

Full Text Available In recent, Google proposed the Project Loon being developed with the mission of providing internet access to rural and remote areas using high-altitude balloons. In this paper, we describe an applicable prototype of 5.8 GHz wireless power transmission system with rough beamforming method to Project Loon. From the measurement results, transmit beamforming phased array antenna can transmit power more efficiently compared to a horn antenna and array antenna without beamforming with increasing the transmission distance. For the transmission distance of 1000 mm, transmit beamforming phased array antenna can obtain higher received power about 1.46 times compared to array antenna without transmit beamforming.

Link-state-estimation-based transmission power control in wireless body area networks.

Science.gov (United States)

Kim, Seungku; Eom, Doo-Seop

2014-07-01

This paper presents a novel transmission power control protocol to extend the lifetime of sensor nodes and to increase the link reliability in wireless body area networks (WBANs). We first experimentally investigate the properties of the link states using the received signal strength indicator (RSSI). We then propose a practical transmission power control protocol based on both short- and long-term link-state estimations. Both the short- and long-term link-state estimations enable the transceiver to adapt the transmission power level and target the RSSI threshold range, respectively, to simultaneously satisfy the requirements of energy efficiency and link reliability. Finally, the performance of the proposed protocol is experimentally evaluated in two experimental scenarios-body posture change and dynamic body motion-and compared with the typical WBAN transmission power control protocols, a real-time reactive scheme, and a dynamic postural position inference mechanism. From the experimental results, it is found that the proposed protocol increases the lifetime of the sensor nodes by a maximum of 9.86% and enhances the link reliability by reducing the packet loss by a maximum of 3.02%.

Energy-efficient wireless mesh infrastructures

OpenAIRE

Al-Hazmi, Y.; de Meer, Hermann; Hummel, Karin Anna; Meyer, Harald; Meo, Michela; Remondo Bueno, David

2011-01-01

The Internet comprises access segments with wired and wireless technologies. In the future, we can expect wireless mesh infrastructures (WMIs) to proliferate in this context. Due to the relatively low energy efficiency of wireless transmission, as compared to wired transmission, energy consumption of WMIs can represent a significant part of the energy consumption of the Internet as a whole. We explore different approaches to reduce energy consumption in WMIs, taking into accoun...

Novel Concepts of Cooperative Wireless Networking

DEFF Research Database (Denmark)

Zhang, Qi

2008-01-01

; secondly, the increasing density of the wireless devices makes cooperation possible; last, the cost of information exchange (i.e. transmission power, transmission time, spectrum, etc.) is very low if information exchange over short-range link is needed. Cooperation changes the way of information delivery......Although wireless networks have achieved great success in the lastest two decades, the current wireless networks have difficulties to fulll users' ever-increasing expectations and needs. It is mainly due to available spectrum resource scarcity, limited battery capacity of wireless device......, unreliable wireless radio link, etc. To tackle these issues, a new telecommunication paradigm has been proposed, referred to as cooperative wireless networking [1]. The basic idea of cooperative wireless networking is that wireless devices work together to achieve their individual goals or one common goal...

Low cost Polymer Optical Fibre based transmission system for feeding integrated broadband wireless in-house LANs

NARCIS (Netherlands)

Ng'Oma, A.; Koonen, A.M.J.; Tafur Monroy, I.; Boom, van den H.P.A.; Smulders, P.F.M.; Khoe, G.D.; Visser, D. Taco; Lenstra, Daan; Schouten, F. Hugo

2002-01-01

A bi-directional transmission system using low cost Polymer Optical Fibre (POF) to feed the required large number of radio access points in next-generation integrated broadband wireless in-house LANs is proposed. Results from simulations and experiments show that, by tuning system parameters, a

Study of a wireless power transmission system for an active capsule endoscope.

Science.gov (United States)

Xin, Wenhui; Yan, Guozheng; Wang, Wenxin

2010-03-01

An active capsule endoscope (ACE) will consume much more energy than can be power by batteries. Its orientation and position are always undetermined when it continues the natural way down the gastrointestinal track. In order to deliver stable and sufficient energy to ACE safely, a wireless power transmission system based on inductive coupling is presented. The system consists of a Helmholtz primary coil outside and a multiple secondary coils inside the body. The Helmholtz primary coil is driven to generate a uniform alternating magnetic field covering the whole of the alimentary tract, and the multiple secondary coils receive energy regardless of the ACE's position and orientation relative to the generated magnetic field. The human tissue safety of the electromagnetic field generated by transmitting coil was evaluated, based on a high-resolution realistic human model. At least 310 mW usable power can be transmitted under the worst geometrical conditions. Outer dimensions of the power receiver, 10 mm diameter x 12 mm; transmitting power, 25 W; resonant frequency, 400 kHz. The maximum specific absorption rate (SAR) and current density of human tissues are 0.329 W/kg and 3.82 A/m(2), respectively, under the basic restrictions of the International Commission on Non-ionizing Radiation Protection (ICNIRP). The designed wireless power transmission is shown to be feasible and potentially safe in a future application. (c) 2010 John Wiley & Sons, Ltd.

Ultracompact Implantable Design With Integrated Wireless Power Transfer and RF Transmission Capabilities.

Science.gov (United States)

Sun, Guilin; Muneer, Badar; Li, Ying; Zhu, Qi

2018-04-01

This paper presents an ultracompact design of biomedical implantable devices with integrated wireless power transfer (WPT) and RF transmission capabilities for implantable medical applications. By reusing the spiral coil in an implantable device, both RF transmission and WPT are realized without the performance degradation of both functions in ultracompact size. The complete theory of WPT based on magnetic resonant coupling is discussed and the design methodology of an integrated structure is presented in detail, which can guide the design effectively. A system with an external power transmitter and implantable structure is fabricated to validate the proposed approach. The experimental results show that the implantable structure can receive power wirelessly at 39.86 MHz with power transfer efficiency of 47.2% and can also simultaneously radiate at 2.45 GHz with an impedance bandwidth of 10.8% and a gain of -15.71 dBi in the desired direction. Furthermore, sensitivity analyses are carried out with the help of experiment and simulation. The results reveal that the system has strong tolerance to the nonideal conditions. Additionally, the specific absorption rate distribution is evaluated in the light of strict IEEE standards. The results reveal that the implantable structure can receive up to 115 mW power from an external transmitter and radiate 6.4 dB·m of power safely.

Layered ACO-OFDM for intensity-modulated direct-detection optical wireless transmission.

Science.gov (United States)

Wang, Qi; Qian, Chen; Guo, Xuhan; Wang, Zhaocheng; Cunningham, David G; White, Ian H

2015-05-04

Layered asymmetrically clipped optical orthogonal frequency division multiplexing (ACO-OFDM) with high spectral efficiency is proposed in this paper for optical wireless transmission employing intensity modulation with direct detection. In contrast to the conventional ACO-OFDM, which only utilizes odd subcarriers for modulation, leading to an obvious spectral efficiency loss, in layered ACO-OFDM, the subcarriers are divided into different layers and modulated by different kinds of ACO-OFDM, which are combined for simultaneous transmission. In this way, more subcarriers are used for data transmission and the spectral efficiency is improved. An iterative receiver is also proposed for layered ACO-OFDM, where the negative clipping distortion of each layer is subtracted once it is detected so that the signals from different layers can be recovered. Theoretical analysis shows that the proposed scheme can improve the spectral efficiency by up to 2 times compared with conventional ACO-OFDM approaches with the same modulation order. Meanwhile, simulation results confirm a considerable signal-to-noise ratio gain over ACO-OFDM at the same spectral efficiency.

Recent Accomplishments in Laser-Photovoltaic Wireless Power Transmission

Science.gov (United States)

Fikes, John C.; Henley, Mark W.; Mankins, John C.; Howell, Joe T.; Fork, Richard L.; Cole, Spencer T.; Skinner, Mark

2003-01-01

Wireless power transmission can be accomplished over long distances using laser power sources and photovoltaic receivers. Recent research at AMOS has improved our understanding of the use of this technology for practical applications. Research by NASA, Boeing, the University of Alabama-Huntsville, the University of Colorado, Harvey Mudd College, and the Naval Postgraduate School has tested various commercial lasers and photovoltaic receiver configurations. Lasers used in testing have included gaseous argon and krypton, solid-state diodes, and fiber optic sources, at wavelengths ranging from the visible to the near infra-red. A variety of Silicon and Gallium Arsenide photovoltaic have been tested with these sources. Safe operating procedures have been established, and initial tests have been conducted in the open air at AMOS facilities. This research is progressing toward longer distance ground demonstrations of the technology and practical near-term space demonstrations.

Risk Factors for Transmission of HIV in a Hospital Environment of Yaoundé, Cameroon

Directory of Open Access Journals (Sweden)

Dora Mbanya

2010-05-01

Full Text Available Risk factors for HIV transmission within a hospital setting were assessed using pre-structured questionnaires and observations. Of 409 respondents, 66.3% corresponded to the nursing staff, 14.4% doctors and 8.3% laboratory staff. The irregular use of gloves and other protective clothing for risky tasks, and recapping of needles after use were some of the risk factors identified, especially amongst nurses. Preventive measures were not always implemented by health personnel. More emphasis should be placed not only on diffusing universal precautions and recommendations for hospital staff safety, but accompanying measures for monitoring and evaluation of implementation of these standards are also indispensable.

A Low-Jitter Wireless Transmission Based on Buffer Management in Coding-Aware Routing

Directory of Open Access Journals (Sweden)

Cunbo Lu

2015-08-01

Full Text Available It is significant to reduce packet jitter for real-time applications in a wireless network. Existing coding-aware routing algorithms use the opportunistic network coding (ONC scheme in a packet coding algorithm. The ONC scheme never delays packets to wait for the arrival of a future coding opportunity. The loss of some potential coding opportunities may degrade the contribution of network coding to jitter performance. In addition, most of the existing coding-aware routing algorithms assume that all flows participating in the network have equal rate. This is unrealistic, since multi-rate environments often appear. To overcome the above problem and expand coding-aware routing to multi-rate scenarios, from the view of data transmission, we present a low-jitter wireless transmission algorithm based on buffer management (BLJCAR, which decides packets in coding node according to the queue-length based threshold policy instead of the regular ONC policy as used in existing coding-aware routing algorithms. BLJCAR is a unified framework to merge the single rate case and multiple rate case. Simulations results show that the BLJCAR algorithm embedded in coding-aware routing outperforms the traditional ONC policy in terms of jitter, packet delivery delay, packet loss ratio and network throughput in network congestion in any traffic rates.

Robust Wireless Power Transmission to mm-Sized Free-Floating Distributed Implants.

Science.gov (United States)

Mirbozorgi, S Abdollah; Yeon, Pyungwoo; Ghovanloo, Maysam

2017-06-01

This paper presents an inductive link for wireless power transmission (WPT) to mm-sized free-floating implants (FFIs) distributed in a large three-dimensional space in the neural tissue that is insensitive to the exact location of the receiver (Rx). The proposed structure utilizes a high-Q resonator on the target wirelessly powered plane that encompasses randomly positioned multiple FFIs, all powered by a large external transmitter (Tx). Based on resonant WPT fundamentals, we have devised a detailed method for optimization of the FFIs and explored design strategies and safety concerns, such as coil segmentation and specific absorption rate limits using realistic finite element simulation models in HFSS including head tissue layers, respectively. We have built several FFI prototypes to conduct accurate measurements and to characterize the performance of the proposed WPT method. Measurement results on 1-mm receivers operating at 60 MHz show power transfer efficiency and power delivered to the load at 2.4% and 1.3 mW, respectively, within 14-18 mm of Tx-Rx separation and 7 cm 2 of brain surface.

Data Transmission Scheme Using Mobile Sink in Static Wireless Sensor Network

Directory of Open Access Journals (Sweden)

Awais Ahmad

2015-01-01

Full Text Available Multihop communication in wireless sensor network (WSN brings new challenges in reliable data transmission. Recent work shows that data collection from sensor nodes using mobile sink minimizes multihop data transmission and improves energy efficiency. However, due to continuous movements, mobile sink has limited communication time to collect data from sensor nodes, which results in rapid depletion of node’s energy. Therefore, we propose a data transmission scheme that addresses the aforementioned constraints. The proposed scheme first finds out the group based region on the basis of localization information of the sensor nodes and predefined trajectory information of a mobile sink. After determining the group region in the network, selection of master nodes is made. The master nodes directly transmit their data to the mobile sink upon its arrival at their group region through restricted flooding scheme. In addition, the agent node concept is introduced for swapping of the role of the master nodes in each group region. The master node when consuming energy up to a certain threshold, neighboring node with second highest residual energy is selected as an agent node. The mathematical analysis shows that the selection of agent node maximizes the throughput while minimizing transmission delay in the network.

Wireless Energy and Information Transmission in FSO and RF-FSO Links

KAUST Repository

Makki, Behrooz

2017-09-22

We propose and analyze a wireless energy and information transmission scheme in free-space optical (FSO) links. The results are presented for both quasi-static and fast-fading conditions. We derive closed-form expressions for throughput, outage probability and optimal power allocation optimizing the system throughput/outage probability. Finally, we complement the FSO link with an additional radio frequency (RF) link to create a hybrid RF-FSO system and reduce the system outage probability. The results show that joint implementation of the RF and FSO links leads to considerable performance improvement, compared to the cases with only FSO-based communication.

Securing DSR with mobile agents in wireless ad hoc networks

Directory of Open Access Journals (Sweden)

Ahmed Abosamra

2011-03-01

Full Text Available Ad hoc wireless network consists of a set of wireless nodes communicating with each other without a pre-defined infrastructure. They communicate by forwarding packets which can reach wireless nodes that do not exist in the range of the direct radio transmission. Designing ad hoc network routing protocols is a challenging task because of its decentralized infrastructure which makes securing ad hoc networks more and more challenging. Dynamic Source Routing (DSR protocol is a popular routing protocol designed for use in wireless ad hoc networks. Mobile agent is a promising technology used in diverse fields of network applications. In this paper, we try to implement DSR using mobile agents for securing this type of wireless network. Hybrid encryption technique (symmetric key encryption/public key encryption is used to improve performance; where symmetric keys are used to encrypt routing data to authenticate and authorize node sending data, while, public keys are used for the exchange of symmetric keys between nodes. We found that DSR may be secured using mobile agents with competitive performance.

Optimization of output power and transmission efficiency of magnetically coupled resonance wireless power transfer system

Science.gov (United States)

Yan, Rongge; Guo, Xiaoting; Cao, Shaoqing; Zhang, Changgeng

2018-05-01

Magnetically coupled resonance (MCR) wireless power transfer (WPT) system is a promising technology in electric energy transmission. But, if its system parameters are designed unreasonably, output power and transmission efficiency will be low. Therefore, optimized parameters design of MCR WPT has important research value. In the MCR WPT system with designated coil structure, the main parameters affecting output power and transmission efficiency are the distance between the coils, the resonance frequency and the resistance of the load. Based on the established mathematical model and the differential evolution algorithm, the change of output power and transmission efficiency with parameters can be simulated. From the simulation results, it can be seen that output power and transmission efficiency of the two-coil MCR WPT system and four-coil one with designated coil structure are improved. The simulation results confirm the validity of the optimization method for MCR WPT system with designated coil structure.

THz Wireless Transmission Systems Based on Photonic Generation of Highly Pure Beat-Notes

DEFF Research Database (Denmark)

Jia, Shi; Yu, Xianbin; Hu, Hao

2016-01-01

In this paper, a terahertz (THz) wireless communication system at 400 GHz with various modulation formats [on–off keying (OOK), quadrature phase-shift keying (QPSK), 16-quadrature amplitude modulation (16-QAM), and 32-quadrature amplitude modulation (32-QAM)] is experimentally demonstrated based...... noise of photonically generated THz beat-notes when phase correlation of two optical comb tones is damaged due to their path-length difference. In addition, we demonstrate THz wireless transmission of various modulation formats, including OOK, QPSK, 16-QAM, and 32-QAM at beyond 10 Gb/s in such a system......, and the measured bit error rate (BER) performance for all the signals after 0.5 m free-space delivery is below the hard decision forward error correction threshold of 3.8 × 10–3. Furthermore, the influence of THz carrier purity on the system performance is experimentally analyzed with respect to the BER of the THz...

Micro-size antenna structure with vertical nanowires for wireless power transmission and communication.

Science.gov (United States)

Kang, Jong-Gu; Jeong, Yeri; Shin, Jeong Hee; Choi, Ji-Woong; Sohn, Jung Inn; Cha, Seung Nam; Jang, Jae Eun

2014-11-01

For biomedical implanted devices, a wireless power or a signal transmission is essential to protect an infection and to enhance durability. In this study, we present a magnetic induction technique for a power transmission without any wire connection between transmitter (Tx) and receiver (Rx) in a micro scale. Due to a micro size effect of a flat spiral coil, a magnetic inductance is not high. To enhance the magnetic inductance, a three dimensional magnetic core is added to an antenna structure, which is consisted of ZnO nano wires coated by a nickel (Ni) layer. ZnO nano wires easily supply a large effective surface area with a vertical structural effect to the magnetic core structure, which induces a higher magnetic inductance with a ferro-magnetic material Ni. The magnetic induction antenna with the magnetic core shows a high inductance value, a low reflection power and a strong power transmission. The power transmission efficiencies are tested under the air and the water medium are almost the same values, so that the magnetic induction technique is quite proper to body implanted systems.

25 Gbit/s QPSK Hybrid Fiber-Wireless Transmission in the W-Band (75–110 GHz) With Remote Antenna Unit for In-Building Wireless Networks

DEFF Research Database (Denmark)

Pang, Xiaodan; Caballero Jambrina, Antonio; Dogadaev, Anton Konstantinovich

2012-01-01

In this paper, we demonstrate a photonic up-converted 25 Gbit/s fiber-wireless quadrature phase shift-keying (QPSK) data transmission link at the W-band (75–110 GHz). By launching two free-running lasers spaced at 87.5 GHz into a standard single-mode fiber (SSMF) at the central office, a W...

New wireless data transmission system based on high frequency radio communication: design, development and testing results under repository conditions

International Nuclear Information System (INIS)

Garcia-Sineriz, J.L.; Barcena, I.; Espada, F.; Rodriguez, A.; Mayor, J.C.; Barnichon, J.D.; Dick, P.

2012-01-01

Document available in extended abstract form only. According to the starting basis of the MoDeRn project (FP7 232598), the design and development of a system capable of transmitting the evolution of the physical parameters inside a repository will be a challenging task due to the harsh working conditions imposed by both the element itself to be monitored (for instance the canister enclosing radioactive waste), the engineered barriers into which they will be embedded and the host rock that contains everything. The measuring devices will work exposed to high pressures, high temperatures, high humidity degrees, presence of radiation, etc., during an expected lifetime of several decades without any possibility of either being powered from any external source or being replaced in case of malfunction, as the operating area will be sealed and inaccessible. Therefore, a main objective of AITEMIN and ENRESA contribution to MoDeRn was focused on the design, development and test under 'real conditions' of a new wireless system, based on high frequency radio transmission (HF), capable of monitoring the physical parameters inside a repository cell independently of the host rock type. In order to achieve the aforementioned objectives and to obtain a suitable monitoring system for the target application, the following key points have been addressed: 1. Data transmission technology (transmission media); 2. Communication protocols; 3. Available power sources; 4. Expected environmental conditions; 5. Suitable sensors. The activities carried out for the development of the HF wireless system were structured in three steps: 1. Laboratory work, to select the best solutions under controlled environment. 2. Field testing, to validate under more realistic conditions the solutions selected at lab. 3. Demonstration: long-term evaluation of the real performance of the solutions proved to be applicable during the field testing Obtained results were as follows: 1. A suitable radio communication

Flexible Transmission Scheme for 4G Wireless Systems with Multiple Antennas

Directory of Open Access Journals (Sweden)

Horlin François

2005-01-01

Full Text Available New air interfaces are currently being developed to meet the high requirements of the emerging wireless communication systems. In this context, the combinations of the multicarrier (MC and spread-spectrum (SS technologies are promising candidates. In this paper, we propose a generic transmission scheme that allows to instantiate all the combinations of orthogonal frequency-division multiplexing (OFDM and cyclic-prefixed single-carrier (SC modulations with direct-sequence code-division multiple access (DS-CDMA. The generic transmission scheme is extended to integrate the space-division multiplexing (SDM and the orthogonal space-time block coding (STBC. Based on a generalized matrix model, the linear frequency-domain minimum mean square error (MMSE joint detector is derived. A mode selection strategy for up- and downlink is advised that efficiently trades off the cost of the mobile terminal and the achieved performance of a high-mobility cellular system. It is demonstrated that an adaptive transceiver that supports the proposed communication modes is necessary to track the changing communication conditions.

A Mixed Transmission Strategy to Achieve Energy Balancing in Wireless Sensor Networks

DEFF Research Database (Denmark)

Liu, Tong; Gu, Tao; Jin, Ning

2017-01-01

In this paper, we investigate the problem of energy balanced data collection in wireless sensor networks, aiming to balance energy consumption among all sensor nodes during the data propagation process. Energy balanced data collection can potentially save energy consumption and prolong network...... lifetime, and hence, it has many practical implications for sensor network design and deployment. The traditional hop-by-hop transmission model allows a sensor node to propagate its packets in a hop-by-hop manner toward the sink, resulting in poor energy balancing for the entire network. To address...... the problem, we apply a slice-based energy model, and divide the problem into inter-slice and intra-slice energy balancing problems. We then propose a probability-based strategy named inter-slice mixed transmission protocol and an intra-slice forwarding technique to address each of the problems. We propose...

30-Gb/s bidirectional transparent optical transmission with an MMF access and an indoor optical wireless link

NARCIS (Netherlands)

Chen, H.; Boom, van den H.P.A.; Tangdiongga, E.; Koonen, A.M.J.

2012-01-01

This letter describes a 30-Gb/s bidirectional transparent optical transmission, over a 4.4-km multimode fiber (MMF) in combination with an indoor optical wireless (OW) link, which could provide limited mobility. Due to MMF's advantages, such as lower installation costs and easy maintenance, it is

EMS Adherence to a Pre-hospital Cervical Spine Clearance Protocol

Directory of Open Access Journals (Sweden)

Johnson, David

2001-10-01

Full Text Available Purpose: To determine the degree of adherence to a cervical spine (c-spine clearance protocol by pre-hospital Emergency Medical Services (EMS personnel by both self-assessment and receiving hospital assessment, to describe deviations from the protocol, and to determine if the rate of compliance by paramedic self-assessment differed from receiving hospital assessment. Methods: A retrospective sample of pre-hospital (consecutive series and receiving hospital (convenience sample assessments of the compliance with and appropriateness of c-spine immobilization. The c-spine clearance protocol was implemented for Orange County EMS just prior to the April-November 1999 data collection period. Results: We collected 396 pre-hospital and 162 receiving hospital data forms. From the pre-hospital data sheet. the percentage deviation from the protocol was 4.096 (16/396. Only one out of 16 cases that did not comply with the protocol was due to over immobilization (0.2%. The remaining 15 cases were under immobilized, according to protocol. Nine of the under immobilized cases (66% that should have been placed in c-spine precautions met physical assessment criteria in the protocol, while the other five cases met mechanism of injury criteria. The rate of deviations from protocol did not differ over time. The receiving hospital identified 8.0% (13/162; 6/16 over immobilized, 7/16 under immobilized of patients with deviations from the protocol; none was determined to have actual c-spine injury. Conclusion: The implementation of a pre-hospital c-spine clearance protocol in Orange County was associated with a moderate overall adherence rate (96% from the pre-hospital perspective, and 92% from the hospital perspective, p=.08 for the two evaluation methods. Most patients who deviated from protocol were under immobilized, but no c-spine injuries were missed. The rate of over immobilization was better than previously reported, implying a saving of resources.

An efficient transmission power control scheme for temperature variation in wireless sensor networks.

Science.gov (United States)

Lee, Jungwook; Chung, Kwangsue

2011-01-01

Wireless sensor networks collect data from several nodes dispersed at remote sites. Sensor nodes can be installed in harsh environments such as deserts, cities, and indoors, where the link quality changes considerably over time. Particularly, changes in transmission power may be caused by temperature, humidity, and other factors. In order to compensate for link quality changes, existing schemes detect the link quality changes between nodes and control transmission power through a series of feedback processes, but these approaches can cause heavy overhead with the additional control packets needed. In this paper, the change of the link quality according to temperature is examined through empirical experimentation. A new power control scheme combining both temperature-aware link quality compensation and a closed-loop feedback process to adapt to link quality changes is proposed. We prove that the proposed scheme effectively adapts the transmission power to the changing link quality with less control overhead and energy consumption.

An Efficient Transmission Power Control Scheme for Temperature Variation in Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Jungwook Lee

2011-03-01

Full Text Available Wireless sensor networks collect data from several nodes dispersed at remote sites. Sensor nodes can be installed in harsh environments such as deserts, cities, and indoors, where the link quality changes considerably over time. Particularly, changes in transmission power may be caused by temperature, humidity, and other factors. In order to compensate for link quality changes, existing schemes detect the link quality changes between nodes and control transmission power through a series of feedback processes, but these approaches can cause heavy overhead with the additional control packets needed. In this paper, the change of the link quality according to temperature is examined through empirical experimentation. A new power control scheme combining both temperature-aware link quality compensation and a closed-loop feedback process to adapt to link quality changes is proposed. We prove that the proposed scheme effectively adapts the transmission power to the changing link quality with less control overhead and energy consumption.

Application of wireless LAN technology to remote monitoring for inspection equipment

International Nuclear Information System (INIS)

Ishiyama, Koichi; Kimura, Takashi; Miura, Yasushi; Yamaguchi, Katsuhiro; Kabuki, Toshihide

2011-01-01

To support inspections under an Integrated Safeguards regime into Tokai Reprocessing Plant (TRP), the IAEA suggested making use of Remote Monitoring (RM) capabilities to the inspection equipment (surveillance camera and NDA systems) installed in the spent fuel storage area at TRP. Since TRP had no pre-prepared cabling infrastructure for data transmission in the spent fuel storage area, the option of wireless LAN was chosen over the telephone line due to its lower installation costs. Feasibility studies and tests were performed by TRP on communication and particularly on long-term continuous communication using wireless LAN equipment composed of APs (AP: Access Point) and the external antennas for introducing wireless LAN technology to RM. As a result it was recognized that wireless LAN has enough ability to communicate for long periods of time and consequently the IAEA installed the AP and the external antenna to each inspection equipment and the wireless LAN technology was applied for RM. In this paper, the summary of each test and the results are reported. (author)

Pre-hospital and hospital delay in patients with non-ST elevation acute coronary syndromes in tertiary care

Directory of Open Access Journals (Sweden)

G.S. Youssef

2017-09-01

Conclusion: Pre-hospital delay was mainly patient-related. Hospital delay was mainly related to healthcare resources. Governmental measures to promote ambulance emergency services may reduce the pre-hospital delay, while improving the utilization of healthcare resources may reduce hospital delay.

Impact of pre-hospital antibiotic use on community-acquired pneumonia.

Science.gov (United States)

Simonetti, A F; Viasus, D; Garcia-Vidal, C; Grillo, S; Molero, L; Dorca, J; Carratalà, J

2014-09-01

Information on the influence of pre-hospital antibiotic treatment on the causative organisms, clinical features and outcomes of patients with community-acquired pneumonia (CAP) remains scarce. We performed an observational study of a prospective cohort of non-immunosuppressed adults hospitalized with CAP between 2003 and 2012. Patients were divided into two groups: those who had received pre-hospital antibiotic treatment for the same episode of CAP and those who had not. A propensity score was used to match patients. Of 2179 consecutive episodes of CAP, 376 (17.3%) occurred in patients who had received pre-hospital antibiotic treatment. After propensity score matching, Legionella pneumophila was more frequently identified in patients with pre-hospital antibiotic treatment, while Streptococcus pneumoniae was less common (p sensitivity and specificity of the pneumococcal urinary antigen test for diagnosing pneumococcal pneumonia were similar in the two groups. Patients with pre-hospital antibiotic treatment were less likely to present fever (p 0.02) or leucocytosis (p 0.001). Conversely, chest X-ray cavitation was more frequent in these patients (p 0.04). No significant differences were found in the frequency of patients classified into high-risk Pneumonia Severity Index classes, in intensive care unit admission, or in 30-day mortality between the groups. In conclusion, L. pneumophila occurrence was nearly three times higher in patients who received pre-hospital antibiotics. After a propensity-adjusted analysis, no significant differences were found in prognosis between study groups. Pre-hospital antibiotic use should be considered when choosing aetiological diagnostic tests and empirical antibiotic therapy in patients with CAP. © 2013 The Authors Clinical Microbiology and Infection © 2013 European Society of Clinical Microbiology and Infectious Diseases.

Miniaturized module for the wireless transmission of measurements with Bluetooth.

Science.gov (United States)

Roth, H; Schwaibold, M; Moor, C; Schöchlin, J; Bolz, A

2002-01-01

The wiring of patients for obtaining medical measurements has many disadvantages. In order to limit these, a miniaturized module was developed which digitalizes analog signals and sends the signal wirelessly to the receiver using Bluetooth. Bluetooth is especially suitable for this application because distances of up to 10 m are possible with low power consumption and robust transmission with encryption. The module consists of a Bluetooth chip, which is initialized in such a way by a microcontroller that connections from other bluetooth receivers can be accepted. The signals are then transmitted to the distant end. The maximum bit rate of the 23 mm x 30 mm module is 73.5 kBit/s. At 4.7 kBit/s, the current consumption is 12 mA.

A wireless transmission neural interface system for unconstrained non-human primates.

Science.gov (United States)

Fernandez-Leon, Jose A; Parajuli, Arun; Franklin, Robert; Sorenson, Michael; Felleman, Daniel J; Hansen, Bryan J; Hu, Ming; Dragoi, Valentin

2015-10-01

Studying the brain in large animal models in a restrained laboratory rig severely limits our capacity to examine brain circuits in experimental and clinical applications. To overcome these limitations, we developed a high-fidelity 96-channel wireless system to record extracellular spikes and local field potentials from the neocortex. A removable, external case of the wireless device is attached to a titanium pedestal placed in the animal skull. Broadband neural signals are amplified, multiplexed, and continuously transmitted as TCP/IP data at a sustained rate of 24 Mbps. A Xilinx Spartan 6 FPGA assembles the digital signals into serial data frames for transmission at 20 kHz though an 802.11n wireless data link on a frequency-shift key-modulated signal at 5.7-5.8 GHz to a receiver up to 10 m away. The system is powered by two CR123A, 3 V batteries for 2 h of operation. We implanted a multi-electrode array in visual area V4 of one anesthetized monkey (Macaca fascicularis) and in the dorsolateral prefrontal cortex (dlPFC) of a freely moving monkey (Macaca mulatta). The implanted recording arrays were electrically stable and delivered broadband neural data over a year of testing. For the first time, we compared dlPFC neuronal responses to the same set of stimuli (food reward) in restrained and freely moving conditions. Although we did not find differences in neuronal responses as a function of reward type in the restrained and unrestrained conditions, there were significant differences in correlated activity. This demonstrates that measuring neural responses in freely moving animals can capture phenomena that are absent in the traditional head-fixed paradigm. We implemented a wireless neural interface for multi-electrode recordings in freely moving non-human primates, which can potentially move systems neuroscience to a new direction by allowing one to record neural signals while animals interact with their environment.

A wireless transmission neural interface system for unconstrained non-human primates

Science.gov (United States)

Fernandez-Leon, Jose A.; Parajuli, Arun; Franklin, Robert; Sorenson, Michael; Felleman, Daniel J.; Hansen, Bryan J.; Hu, Ming; Dragoi, Valentin

2015-10-01

Objective. Studying the brain in large animal models in a restrained laboratory rig severely limits our capacity to examine brain circuits in experimental and clinical applications. Approach. To overcome these limitations, we developed a high-fidelity 96-channel wireless system to record extracellular spikes and local field potentials from the neocortex. A removable, external case of the wireless device is attached to a titanium pedestal placed in the animal skull. Broadband neural signals are amplified, multiplexed, and continuously transmitted as TCP/IP data at a sustained rate of 24 Mbps. A Xilinx Spartan 6 FPGA assembles the digital signals into serial data frames for transmission at 20 kHz though an 802.11n wireless data link on a frequency-shift key-modulated signal at 5.7-5.8 GHz to a receiver up to 10 m away. The system is powered by two CR123A, 3 V batteries for 2 h of operation. Main results. We implanted a multi-electrode array in visual area V4 of one anesthetized monkey (Macaca fascicularis) and in the dorsolateral prefrontal cortex (dlPFC) of a freely moving monkey (Macaca mulatta). The implanted recording arrays were electrically stable and delivered broadband neural data over a year of testing. For the first time, we compared dlPFC neuronal responses to the same set of stimuli (food reward) in restrained and freely moving conditions. Although we did not find differences in neuronal responses as a function of reward type in the restrained and unrestrained conditions, there were significant differences in correlated activity. This demonstrates that measuring neural responses in freely moving animals can capture phenomena that are absent in the traditional head-fixed paradigm. Significance. We implemented a wireless neural interface for multi-electrode recordings in freely moving non-human primates, which can potentially move systems neuroscience to a new direction by allowing one to record neural signals while animals interact with their environment.

Wireless ATM : handover issues

OpenAIRE

Jiang, Fan; Käkölä, Timo

1998-01-01

Basic aspects of cellular systems and the ATM transmission technology are introduced. Wireless ATM is presented as a combination of radio ATM and mobile ATM. Radio ATM is a wireless extension of an ATM connection while mobile ATM contains the necessary extensions to ATM to support mobility. Because the current ATM technology does not support mobility, handover becomes one of the most important research issues for wireless ATM. Wireless ATM handover requirements are thus analysed. A handover s...

Wireless autonomous device data transmission

Science.gov (United States)

Sammel, Jr., David W. (Inventor); Cain, James T. (Inventor); Mickle, Marlin H. (Inventor); Mi, Minhong (Inventor)

2013-01-01

A method of communicating information from a wireless autonomous device (WAD) to a base station. The WAD has a data element having a predetermined profile having a total number of sequenced possible data element combinations. The method includes receiving at the WAD an RF profile transmitted by the base station that includes a triggering portion having a number of pulses, wherein the number is at least equal to the total number of possible data element combinations. The method further includes keeping a count of received pulses and wirelessly transmitting a piece of data, preferably one bit, to the base station when the count reaches a value equal to the stored data element's particular number in the sequence. Finally, the method includes receiving the piece of data at the base station and using the receipt thereof to determine which of the possible data element combinations the stored data element is.

Low-complexity video encoding method for wireless image transmission in capsule endoscope.

Science.gov (United States)

Takizawa, Kenichi; Hamaguchi, Kiyoshi

2010-01-01

This paper presents a low-complexity video encoding method applicable for wireless image transmission in capsule endoscopes. This encoding method is based on Wyner-Ziv theory, in which side information available at a transmitter is treated as side information at its receiver. Therefore complex processes in video encoding, such as estimation of the motion vector, are moved to the receiver side, which has a larger-capacity battery. As a result, the encoding process is only to decimate coded original data through channel coding. We provide a performance evaluation for a low-density parity check (LDPC) coding method in the AWGN channel.

Gait-Cycle-Driven Transmission Power Control Scheme for a Wireless Body Area Network.

Science.gov (United States)

Zang, Weilin; Li, Ye

2018-05-01

In a wireless body area network (WBAN), walking movements can result in rapid channel fluctuations, which severely degrade the performance of transmission power control (TPC) schemes. On the other hand, these channel fluctuations are often periodic and are time-synchronized with the user's gait cycle, since they are all driven from the walking movements. In this paper, we propose a novel gait-cycle-driven transmission power control (G-TPC) for a WBAN. The proposed G-TPC scheme reinforces the existing TPC scheme by exploiting the periodic channel fluctuation in the walking scenario. In the proposed scheme, the user's gait cycle information acquired by an accelerometer is used as beacons for arranging the transmissions at the time points with the ideal channel state. The specific transmission power is then determined by using received signal strength indication (RSSI). An experiment was conducted to evaluate the energy efficiency and reliability of the proposed G-TPC based on a CC2420 platform. The results reveal that compared to the original RSSI/link-quality-indication-based TPC, G-TPC reduces energy consumption by 25% on the sensor node and reduce the packet loss rate by 65%.

A Provably-Secure Transmission Scheme for Wireless Body Area Networks.

Science.gov (United States)

Omala, Anyembe Andrew; Robert, Niyifasha; Li, Fagen

2016-11-01

Wireless body area network (WBANs) is composed of sensors that collect and transmit a person's physiological data to health-care providers in real-time. In order to guarantee security of this data over open networks, a secure data transmission mechanism between WBAN and application provider's servers is of necessity. Modified medical data does not provide a true reflection of an individuals state of health and its subsequent use for diagnosis could lead to an irreversible medical condition. In this paper, we propose a lightweight certificateless signcryption scheme for secure transmission of data between WBAN and servers. Our proposed scheme not only provides confidentiality of data and authentication in a single logical step, it is lightweight and resistant to key escrow attacks. We further provide security proof that our scheme provides indistinguishability against adaptive chosen ciphertext attack and unforgeability against adaptive chosen message attack in random oracle model. Compared with two other Diffie-Hellman based signcryption schemes proposed by Barbosa and Farshim (BF) and another by Yin and Liang (YL), our scheme consumes 46 % and 8 % less energy during signcryption than BF and YL scheme respectively.

A video wireless capsule endoscopy system powered wirelessly: design, analysis and experiment

International Nuclear Information System (INIS)

Pan, Guobing; Chen, Jiaoliao; Xin, Wenhui; Yan, Guozheng

2011-01-01

Wireless capsule endoscopy (WCE), as a relatively new technology, has brought about a revolution in the diagnosis of gastrointestinal (GI) tract diseases. However, the existing WCE systems are not widely applied in clinic because of the low frame rate and low image resolution. A video WCE system based on a wireless power supply is developed in this paper. This WCE system consists of a video capsule endoscope (CE), a wireless power transmission device, a receiving box and an image processing station. Powered wirelessly, the video CE has the abilities of imaging the GI tract and transmitting the images wirelessly at a frame rate of 30 frames per second (f/s). A mathematical prototype was built to analyze the power transmission system, and some experiments were performed to test the capability of energy transferring. The results showed that the wireless electric power supply system had the ability to transfer more than 136 mW power, which was enough for the working of a video CE. In in vitro experiments, the video CE produced clear images of the small intestine of a pig with the resolution of 320 × 240, and transmitted NTSC format video outside the body. Because of the wireless power supply, the video WCE system with high frame rate and high resolution becomes feasible, and provides a novel solution for the diagnosis of the GI tract in clinic

Bifurcation Analysis for an SEIRS-V Model with Delays on the Transmission of Worms in a Wireless Sensor Network

Directory of Open Access Journals (Sweden)

Zizhen Zhang

2017-01-01

Full Text Available Hopf bifurcation for an SEIRS-V model with delays on the transmission of worms in a wireless sensor network is investigated. We focus on existence of the Hopf bifurcation by regarding the diverse delay as a bifurcation parameter. The results show that propagation of worms in the wireless sensor network can be controlled when the delay is suitably small under some certain conditions. Then, we study properties of the Hopf bifurcation by using the normal form theory and center manifold theorem. Finally, we give a numerical example to support the theoretical results.

A Lifetime Optimization Algorithm Limited by Data Transmission Delay and Hops for Mobile Sink-Based Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Yourong Chen

2017-01-01

Full Text Available To improve the lifetime of mobile sink-based wireless sensor networks and considering that data transmission delay and hops are limited in actual system, a lifetime optimization algorithm limited by data transmission delay and hops (LOA_DH for mobile sink-based wireless sensor networks is proposed. In LOA_DH, some constraints are analyzed, and an optimization model is proposed. Maximum capacity path routing algorithm is used to calculate the energy consumption of communication. Improved genetic algorithm which modifies individuals to meet all constraints is used to solve the optimization model. The optimal solution of sink node’s sojourn grid centers and sojourn times which maximizes network lifetime is obtained. Simulation results show that, in three node distribution scenes, LOA_DH can find the movement solution of sink node which covers all sensor nodes. Compared with MCP_RAND, MCP_GMRE, and EASR, the solution improves network lifetime and reduces average amount of node discarded data and average energy consumption of nodes.

Performance of a 60-GHz DCM-OFDM and BPSK-Impulse Ultra-Wideband System with Radio-Over-Fiber and Wireless Transmission Employing a Directly-Modulated VCSEL

DEFF Research Database (Denmark)

Beltrán, Marta; Jensen, Jesper Bevensee; Yu, Xianbin

2011-01-01

The performance of radio-over-fiber optical transmission employing vertical-cavity surface-emitting lasers (VCSELs), and further wireless transmission, of the two major ultra-wideband (UWB) implementations is reported when operating in the 60-GHz radio band. Performance is evaluated at 1.44 Gbit...... in bend-insensitive single-mode fiber with wireless transmission up to 5 m in both cases is demonstrated with no penalty. A simulation analysis has also been performed in order to investigate the operational limits. The analysis results are in excellent agreement with the experimental work and indicate...... good tolerance to chromatic dispersion due to the chirp characteristics of electro-optical conversion when a directly-modulated VCSEL is employed. The performance comparison indicates that BPSK-IR UWB exhibits better tolerance to optical transmission impairments requiring lower received optical power...

Frame Transmission Efficiency-Based Cross-Layer Congestion Notification Scheme in Wireless Ad Hoc Networks.

Science.gov (United States)

He, Huaguang; Li, Taoshen; Feng, Luting; Ye, Jin

2017-07-15

Different from the traditional wired network, the fundamental cause of transmission congestion in wireless ad hoc networks is medium contention. How to utilize the congestion state from the MAC (Media Access Control) layer to adjust the transmission rate is core work for transport protocol design. However, recent works have shown that the existing cross-layer congestion detection solutions are too complex to be deployed or not able to characterize the congestion accurately. We first propose a new congestion metric called frame transmission efficiency (i.e., the ratio of successful transmission delay to the frame service delay), which describes the medium contention in a fast and accurate manner. We further present the design and implementation of RECN (ECN and the ratio of successful transmission delay to the frame service delay in the MAC layer, namely, the frame transmission efficiency), a general supporting scheme that adjusts the transport sending rate through a standard ECN (Explicit Congestion Notification) signaling method. Our method can be deployed on commodity switches with small firmware updates, while making no modification on end hosts. We integrate RECN transparently (i.e., without modification) with TCP on NS2 simulation. The experimental results show that RECN remarkably improves network goodput across multiple concurrent TCP flows.

Knowledge and perceptions of HIV/AIDS and mother to child transmission among antenatal mothers at Nnamdi Azikiwe University Teaching hospital, Nnewi.

Science.gov (United States)

Igwegbe, A O; Ilika, A L

2005-12-01

Knowledge of HIV/AIDS by pregnant mothers is very important in the prevention of mother to child transmission. This study evaluates the knowledge and perceptions of HIV/AIDS and mother to child transmission among pregnant women attending antenatal clinic at a University Teaching Hospital. Pre-tested questionnaires were interviewer administered to 312 pregnant women randomly selected at the antenatal clinic of the Nnamdi Azikiwe University Teaching Hospital Nnewi. The level of awareness of HIV/AIDS among antenatal mothers was very high (99%) and the main sources of information were radio (44.7%), television (38.8%), and print media (34.0%). Though majority (94.2%) was aware HIV infection can coexist with pregnancy, only 76.9% were aware of mother to child transmission. Transplacental (46.1%), breastfeeding (31.7%), and vaginal delivery (16.3%) were the commonly identified routes of vertical transmission. Surprisingly, eighteen respondents (5.8%) indicated that caesarean section is a possible route of vertical transmission. Though the percentage of HIV/AIDS knowledge is high, the level of knowledge and perceptions of mother to child transmission is inadequate. This suggests the need to scale up health education about mother to child transmission in our health facilities.

Wireless Power Transmission Options for Space Solar Power

Science.gov (United States)

Potter, Seth; Davis, Dean; Born, Martin; Bayer, Martin; Howell, Joe; Mankins, John

2008-01-01

Space Solar Power (SSP), combined with Wireless Power Transmission (WPT), offers the far-term potential to solve major energy problems on Earth. In the long term, we aspire to beam energy to Earth from geostationary Earth orbit (GEO), or even further distances in space. In the near term, we can beam power over more moderate distances, but still stretch the limits of today s technology. In recent studies, a 100 kWe-class "Power Plug" Satellite and a 10 kWe-class Lunar Polar Solar Power outpost have been considered as the first steps in using these WPT options for SSP. Our current assessments include consideration of orbits, wavelengths, and structural designs to meet commercial, civilian government, and military needs. Notional transmitter and receiver sizes are considered for use in supplying 5 to 40 MW of power. In the longer term, lunar or asteroidal material can be used. By using SSP and WPT technology for near-term missions, we gain experience needed for sound decisions in designing and developing larger systems to send power from space to Earth.

Research on Matrix-type Packet Loss Compensation Scheme for Wireless Video Transmission on Subway

Directory of Open Access Journals (Sweden)

Fan Qing-Wu

2017-01-01

Full Text Available As the mainstream wireless LAN technology, Wi-Fi can achieve fast data transfer. With the subway moving in a high speed, video data transmission between the metro and the ground is achieved through Wi-Fi technology. This paper aims at solving the Caton problem caused by switching packet loss in the process of playing real-time video on the train terminal, and proposes matrix-type packet loss compensation scheme. Finally, the feasibility of the scheme is verified by experiments.

Comparative Analysis of Torque and Acceleration of Pre- and Post-Transmission Parallel Hybrid Drivetrains

Directory of Open Access Journals (Sweden)

Zulkifli Saiful A.

2016-01-01

Full Text Available Parallel hybrid electric vehicles (HEV can be classified according to the location of the electric motor with respect to the transmission unit for the internal combustion engine (ICE: they can be pre-transmission or posttransmission parallel hybrid. A split-axle parallel HEV – in which the ICE and electric motor provide propulsion power to different axles – is a sub-type of the post-transmission hybrid, since addition of torque and power from the two power sources occurs after the vehicle’s transmission. The term ‘through-the-road’ (TTR hybrid is also used for the split-parallel HEV, since power coupling between the ICE and electric motor is not through some mechanical device but through the vehicle itself, its wheels and the road on which it moves. The present work presents torquespeed relationship of the split-parallel hybrid and analyses simulation results of torque profiles and acceleration performance of pre-transmission and post-transmission hybrid configurations, using three different sizes of electric motor. Different operating regions of the pre-trans and post-trans motors are observed, leading to different speed and torque profiles. Although ICE average efficiency in the post-trans hybrid is slightly lower than in the pre-trans hybrid, the post-trans hybrid vehicle has better fuel economy and acceleration performance than the pre-trans hybrid vehicle.

R and D of suitable unit to heightening in grade of mobile wireless telegraphy system; Test on data transmission characteristics and research on transmission method. Ido musen system no kodoka ni tekigo kano na sochi no kaihatsu kenkyu; Deta denso tokusei shiken oyobi denso hoho no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Onigawara, Shuichi; Koyama, Masayoshi; Masunaga, Katsutoshi [Kyushu Electric Power Co., Inc., Fukuoka (Japan)

1989-03-30

In order to heighten the grade by the present mobile wireless telegraphy system, through the experimentation and research on both data transmission and error correction methods, both data and facsimile transmission were confirmed to be possible together with the following result: In the character transmission by a CPU connection and other encoded transmissions in which even an error by one bit considerably influences the contents of data, 1200bps, as able to be widened in service area, is profitable. While the data transmission in the mobile wireless telegraphy generates many errors due to phasing and noise along the propagation route. To attenuate those errors, error correction encoding is effectively applied with a correction method to be selected by kind of data. Further the 150MHz band, as more largely influenced by urban noise than the 400MHz band, narrows service area in the urban district. While the mobile wireless telegraphy is restricted in frequency band region. 12 refs., 26 figs., 9 tabs.

Code-Hopping Based Transmission Scheme for Wireless Physical-Layer Security

Directory of Open Access Journals (Sweden)

Liuguo Yin

2018-01-01

Full Text Available Due to the broadcast and time-varying natures of wireless channels, traditional communication systems that provide data encryption at the application layer suffer many challenges such as error diffusion. In this paper, we propose a code-hopping based secrecy transmission scheme that uses dynamic nonsystematic low-density parity-check (LDPC codes and automatic repeat-request (ARQ mechanism to jointly encode and encrypt source messages at the physical layer. In this scheme, secret keys at the transmitter and the legitimate receiver are generated dynamically upon the source messages that have been transmitted successfully. During the transmission, each source message is jointly encoded and encrypted by a parity-check matrix, which is dynamically selected from a set of LDPC matrices based on the shared dynamic secret key. As for the eavesdropper (Eve, the uncorrectable decoding errors prevent her from generating the same secret key as the legitimate parties. Thus she cannot select the correct LDPC matrix to recover the source message. We demonstrate that our scheme can be compatible with traditional cryptosystems and enhance the security without sacrificing the error-correction performance. Numerical results show that the bit error rate (BER of Eve approaches 0.5 as the number of transmitted source messages increases and the security gap of the system is small.

1KW Power Transmission Using Wireless Acoustic-Electric Feed-Through (WAEF)

Science.gov (United States)

Sherrit, S.; Bao, X.; Badescu, M.; Aldrich, J.; Bar-Cohen, Y.; Biederman, W.

2008-01-01

A variety of space applications require the delivery of power into sealed structures. Since the structural integrity can be degraded by holes for cabling we present an alternative method of delivering power and information using stress waves to the internal space of a sealed structure. One particular application of this technology is in sample return missions where it is critical to preserve the sample integrity and to prevent earth contamination. Therefore, the container has to be hermetically sealed and the integrity of the seal must be monitored in order to insure to a high degree of reliability the integrity of the sample return vessel. In this study we investigated the use of piezoelectric acoustic-electric power feed-through devices to transfer electric power wirelessly through a solid wall by using elastic or acoustic waves. The technology is applicable to a range of space and terrestrial applications where power is required by electronic equipment inside sealed containers, vacuum or pressure vessels, etc., where holes in the wall are prohibitive or may result in significant structural performance degradation or unnecessarily complex designs. To meet requirements of higher power applications, the feasibility to transfer kilowatts level power was investigated. Pre-stressed longitudinal piezoelectric feed-through devices were analyzed by finite element models and an equivalent circuit model was developed to predict the power transfer characteristics to different electric loads. Based on the results of the analysis a prototype device was designed, fabricated and a demonstration of the transmission of electric power up to 1.068-kW was successfully conducted. Efficiencies in the 80-90% range were also demonstrated and methods to increase the efficiency further are currently being considered.

Electromagnetic interference-aware transmission scheduling and power control for dynamic wireless access in hospital environments.

Science.gov (United States)

Phunchongharn, Phond; Hossain, Ekram; Camorlinga, Sergio

2011-11-01

We study the multiple access problem for e-Health applications (referred to as secondary users) coexisting with medical devices (referred to as primary or protected users) in a hospital environment. In particular, we focus on transmission scheduling and power control of secondary users in multiple spatial reuse time-division multiple access (STDMA) networks. The objective is to maximize the spectrum utilization of secondary users and minimize their power consumption subject to the electromagnetic interference (EMI) constraints for active and passive medical devices and minimum throughput guarantee for secondary users. The multiple access problem is formulated as a dual objective optimization problem which is shown to be NP-complete. We propose a joint scheduling and power control algorithm based on a greedy approach to solve the problem with much lower computational complexity. To this end, an enhanced greedy algorithm is proposed to improve the performance of the greedy algorithm by finding the optimal sequence of secondary users for scheduling. Using extensive simulations, the tradeoff in performance in terms of spectrum utilization, energy consumption, and computational complexity is evaluated for both the algorithms.

REVIEW OF WIRELESS MIMO CHANNEL MODELS

African Journals Online (AJOL)

user

MIMO wireless system, the transmitted signal interacts ... delay spread information, power delay profile, angle of arrival and ... With the advent of the MIMO wireless systems, there arose a ..... associated with channel transmission and reception.

LBMR: Load-Balanced Multipath Routing for Wireless Data-Intensive Transmission in Real-Time Medical Monitoring.

Science.gov (United States)

Tseng, Chinyang Henry

2016-05-31

In wireless networks, low-power Zigbee is an excellent network solution for wireless medical monitoring systems. Medical monitoring generally involves transmission of a large amount of data and easily causes bottleneck problems. Although Zigbee's AODV mesh routing provides extensible multi-hop data transmission to extend network coverage, it originally does not, and needs to support some form of load balancing mechanism to avoid bottlenecks. To guarantee a more reliable multi-hop data transmission for life-critical medical applications, we have developed a multipath solution, called Load-Balanced Multipath Routing (LBMR) to replace Zigbee's routing mechanism. LBMR consists of three main parts: Layer Routing Construction (LRC), a Load Estimation Algorithm (LEA), and a Route Maintenance (RM) mechanism. LRC assigns nodes into different layers based on the node's distance to the medical data gateway. Nodes can have multiple next-hops delivering medical data toward the gateway. All neighboring layer-nodes exchange flow information containing current load, which is the used by the LEA to estimate future load of next-hops to the gateway. With LBMR, nodes can choose the neighbors with the least load as the next-hops and thus can achieve load balancing and avoid bottlenecks. Furthermore, RM can detect route failures in real-time and perform route redirection to ensure routing robustness. Since LRC and LEA prevent bottlenecks while RM ensures routing fault tolerance, LBMR provides a highly reliable routing service for medical monitoring. To evaluate these accomplishments, we compare LBMR with Zigbee's AODV and another multipath protocol, AOMDV. The simulation results demonstrate LBMR achieves better load balancing, less unreachable nodes, and better packet delivery ratio than either AODV or AOMDV.

Wireless security in mobile health.

Science.gov (United States)

Osunmuyiwa, Olufolabi; Ulusoy, Ali Hakan

2012-12-01

Mobile health (m-health) is an extremely broad term that embraces mobile communication in the health sector and data packaging. The four broad categories of wireless networks are wireless personal area network, wireless metropolitan area network, wireless wide area network, and wireless local area network. Wireless local area network is the most notable of the wireless networking tools obtainable in the health sector. Transfer of delicate and critical information on radio frequencies should be secure, and the right to use must be meticulous. This article covers the business opportunities in m-health, threats faced by wireless networks in hospitals, and methods of mitigating these threats.

Multigigabit W-Band (75–110 GHz) Bidirectional Hybrid Fiber-Wireless Systems in Access Networks

DEFF Research Database (Denmark)

Pang, Xiaodan; Lebedev, Alexander; Vegas Olmos, Juan José

2014-01-01

compare the transmission performances in terms of achievable wireless distances with and without using a high-frequency electrical power amplifier at the wireless transmitter. A downlink 16-Gbit/s QPSK signal and an uplink 1.25-Gbit/s ASK signal transmission over the two implementations are experimentally......We experimentally demonstrate multigigabit capacity bidirectional hybrid fiber-wireless systems with RF carrier frequencies at the W-band (75-110 GHz) that enables the seamless convergence between wireless and fiber-optic data transmission systems in access networks. In this study, we evaluate...... the transmission performances in two scenarios: a fiber-wireless access link that directly provide high-speed connections to wireless end users, and a fiber-wireless-fiber signal relay where a high capacity wireless link can be used to bridge two access fiber spans over physical obstacles. In both scenarios, we...

A Survey on Sensor Coverage and Visual Data Capturing/Processing/Transmission in Wireless Visual Sensor Networks

Directory of Open Access Journals (Sweden)

Florence G. H. Yap

2014-02-01

Full Text Available Wireless Visual Sensor Networks (WVSNs where camera-equipped sensor nodes can capture, process and transmit image/video information have become an important new research area. As compared to the traditional wireless sensor networks (WSNs that can only transmit scalar information (e.g., temperature, the visual data in WVSNs enable much wider applications, such as visual security surveillance and visual wildlife monitoring. However, as compared to the scalar data in WSNs, visual data is much bigger and more complicated so intelligent schemes are required to capture/process/ transmit visual data in limited resources (hardware capability and bandwidth WVSNs. WVSNs introduce new multi-disciplinary research opportunities of topics that include visual sensor hardware, image and multimedia capture and processing, wireless communication and networking. In this paper, we survey existing research efforts on the visual sensor hardware, visual sensor coverage/deployment, and visual data capture/ processing/transmission issues in WVSNs. We conclude that WVSN research is still in an early age and there are still many open issues that have not been fully addressed. More new novel multi-disciplinary, cross-layered, distributed and collaborative solutions should be devised to tackle these challenging issues in WVSNs.

Wireless mesh networks.

Science.gov (United States)

Wang, Xinheng

2008-01-01

Wireless telemedicine using GSM and GPRS technologies can only provide low bandwidth connections, which makes it difficult to transmit images and video. Satellite or 3G wireless transmission provides greater bandwidth, but the running costs are high. Wireless networks (WLANs) appear promising, since they can supply high bandwidth at low cost. However, the WLAN technology has limitations, such as coverage. A new wireless networking technology named the wireless mesh network (WMN) overcomes some of the limitations of the WLAN. A WMN combines the characteristics of both a WLAN and ad hoc networks, thus forming an intelligent, large scale and broadband wireless network. These features are attractive for telemedicine and telecare because of the ability to provide data, voice and video communications over a large area. One successful wireless telemedicine project which uses wireless mesh technology is the Emergency Room Link (ER-LINK) in Tucson, Arizona, USA. There are three key characteristics of a WMN: self-organization, including self-management and self-healing; dynamic changes in network topology; and scalability. What we may now see is a shift from mobile communication and satellite systems for wireless telemedicine to the use of wireless networks based on mesh technology, since the latter are very attractive in terms of cost, reliability and speed.

Bio-Inspired Distributed Transmission Power Control Considering QoS Fairness in Wireless Body Area Sensor Networks.

Science.gov (United States)

Lee, Chan-Jae; Jung, Ji-Young; Lee, Jung-Ryun

2017-10-14

Recently, the development of wireless body area sensor network (WBASN) has accelerated due to the rapid development of wireless technology. In the WBASN environment, many WBASNs coexist where communication ranges overlap with each other, resulting in the possibility of interference. Although nodes in a WBASN typically operate at a low power level, to avoid adversely affecting the human body, high transmission rates may be required to support some applications. In addition to this, since many varieties of applications exist in the WBASN environment, each prospective user may have different quality of service (QoS) requirements. Hence, the following issues should be considered in the WBASN environment: (1) interference between adjacent WBASNs, which influences the performance of a specific system, and (2) the degree of satisfaction on the QoS of each user, i.e., the required QoS such as user throughput should be considered to ensure that all users in the network are provided with a fair QoS satisfaction. Thus, in this paper, we propose a transmission power adjustment algorithm that addresses interference problems and guarantees QoS fairness between users. First, we use a new utility function to measure the degree of the satisfaction on the QoS for each user. Then, the transmission power of each sensor node is calculated using the Cucker-Smale model, and the QoS satisfaction of each user is synchronized dispersively. The results of simulations show that the proposed algorithm performs better than existing algorithms, with respect to QoS fairness and energy efficiency.

Development of Radiation-Resistant In-Water Wireless Transmission System Using Light Emitting Diodes and Photo Diodes

Science.gov (United States)

Takeuchi, T.; Shibata, H.; Otsuka, N.; Uehara, T.; Tsuchiya, K.; Shibagaki, T.; Komanome, H.

2016-10-01

Several kinds of commercially available light emitting diodes (LED) and photo diodes (PD) were irradiated with 60Co gamma ray up to 1 MGy for development of a radiation-resistant in-water wireless transmission system using visible light. The lens parts of the LEDs turned brown by the irradiation and their colors became dark with the absorbed dose. The total luminous fluxes decreased with the absorbed dose and the LED with shorter emission wavelength had the higher decrease rate. Meanwhile, the current-voltage characteristics hardly changed. These results indicate that the decreases of the total luminous flux of the LEDs were mainly caused not by the degradation of the semiconductor parts but by the coloring of the lens parts by the irradiation. On the other hand, the light sensitivities of the PDs decreased with the absorbed dose. The PDs with the window part which turned a darker color had the higher decrease rate. These results indicate that the decreases of light sensitivities of the PDs were also mainly caused by the coloring of the resin parts by the irradiation. If the wireless transmission is performed using the candidate LED and PD between 5 meters in water, using a few LEDs and PDs, the PD's output current generated by the emission light of the LED is estimated to be detectable even considering the effects of the absorption of the light in water and the increased dark current by the irradiation. Therefore, a radiation resistant in-water transmission system can be constructed using commercially available LEDs and PDs in principle.

Transmission History Based Distributed Adaptive Contention Window Adjustment Algorithm Cooperating with Automatic Rate Fallback for Wireless LANs

Science.gov (United States)

Ogawa, Masakatsu; Hiraguri, Takefumi; Nishimori, Kentaro; Takaya, Kazuhiro; Murakawa, Kazuo

This paper proposes and investigates a distributed adaptive contention window adjustment algorithm based on the transmission history for wireless LANs called the transmission-history-based distributed adaptive contention window adjustment (THAW) algorithm. The objective of this paper is to reduce the transmission delay and improve the channel throughput compared to conventional algorithms. The feature of THAW is that it adaptively adjusts the initial contention window (CWinit) size in the binary exponential backoff (BEB) algorithm used in the IEEE 802.11 standard according to the transmission history and the automatic rate fallback (ARF) algorithm, which is the most basic algorithm in automatic rate controls. This effect is to keep CWinit at a high value in a congested state. Simulation results show that the THAW algorithm outperforms the conventional algorithms in terms of the channel throughput and delay, even if the timer in the ARF is changed.

Real-Time and Secure Wireless Health Monitoring

Science.gov (United States)

Dağtaş, S.; Pekhteryev, G.; Şahinoğlu, Z.; Çam, H.; Challa, N.

2008-01-01

We present a framework for a wireless health monitoring system using wireless networks such as ZigBee. Vital signals are collected and processed using a 3-tiered architecture. The first stage is the mobile device carried on the body that runs a number of wired and wireless probes. This device is also designed to perform some basic processing such as the heart rate and fatal failure detection. At the second stage, further processing is performed by a local server using the raw data transmitted by the mobile device continuously. The raw data is also stored at this server. The processed data as well as the analysis results are then transmitted to the service provider center for diagnostic reviews as well as storage. The main advantages of the proposed framework are (1) the ability to detect signals wirelessly within a body sensor network (BSN), (2) low-power and reliable data transmission through ZigBee network nodes, (3) secure transmission of medical data over BSN, (4) efficient channel allocation for medical data transmission over wireless networks, and (5) optimized analysis of data using an adaptive architecture that maximizes the utility of processing and computational capacity at each platform. PMID:18497866

Exploring Relay Cooperation for Secure and Reliable Transmission in Two-HopWireless Networks

Directory of Open Access Journals (Sweden)

Yulong Shen

2014-03-01

Full Text Available This work considers the problem of secure and reliable information transmission via relay cooperation in two-hop relay wireless networks without the information of both eavesdropper channels and locations. While previous work on this problem mainly studied infinite networks and their asymptotic behavior and scaling law results, this papers focuses on a more practical network with finite number of system nodes and explores the corresponding exact result on the number of eavesdroppers one network can tolerate to ensure desired secrecy and reliability. We first study the scenario where path-loss is equal between all pairs of nodes and consider two transmission protocols there, one adopts an optimal but complex relay selection process with less load balance capacity while the other adopts a random but simple relay selection process with good load balance capacity. Theoretical analysis and numerical results are then provided to determine the maximum number of eavesdroppers one network can tolerate to ensure a desired performance in terms of the secrecy outage probability and transmission outage probability. We further extend our study to the more general scenario where path-loss between each pair of nodes also depends on the distance between them, for which a new transmission protocol with both preferable relay selection and good load balance as well as the corresponding theoretical analysis and numerical results are presented.

Experimental Performance Comparison of 60 GHz DCM OFDM and Impulse BPSK Ultra-Wideband with Combined Optical Fibre and Wireless Transmission

DEFF Research Database (Denmark)

Beltrán, Marta; Jensen, Jesper Bevensee; Yu, Xianbin

2010-01-01

We present an experimental performance comparison of 1.44Gbps dual-carrier modulation OFDM and BPSK impulse-radio ultra-wideband in the 60GHz band with combined fibre, up to 40km, and 5m wireless transmission. Impulse-radio exhibits better dispersion tolerance requiring lower optical power....

Space power transmission

Energy Technology Data Exchange (ETDEWEB)

Kuribayashi, Shizuma [Mitsubishi Heavy Industries, Ltd., Tokyo, (Japan)

1989-10-05

There being a conception to utilize solar energy by use of a space power station (SPS), a method to bring that universal grace to mankind is wireless energy transmission. The wireless energy transmission is regarded to be microwave transmission or laser beam transmission. The microwave transmission is to transmit 2.45GHz band microwave from the SPS to a receiving station on the ground to meet power demand on earth. The microwave, as small in attenuation in atmosphere and resistant against rain and cloud, is made candidate and, however, problematic in influence on organism, necessary large area of receiving antenna and many other points to be studied. While the laser transmission, as more convergent of beam than the microwave transmission, is advantageous with enabling the receiving area to be small and, however, disadvantageous with being not resistant against dust, rain and cloud, if used for the energy transmission between the space and earth. 2 refs., 2 figs.

Remote Access Unit for Optic-to-Wireless Conversion

DEFF Research Database (Denmark)

Chorchos, Łukasz; Rommel, Simon; Turkiewicz, J. P.

. Growing demand for high speed wireless data transmission and new wireless standards like 5G force network operators to find new solutions for backhaul networks. Presently, to meet this need, attention of many researchers and top network vendors has been directed towards millimeter wave radio links....... Operation in the millimeter wave range brings new possibilities for a channel allocation as well as allows wider radio channels to be used. Moreover this frequency range is lighter licensed than regular GSM. This clearly shows a huge potential of millimeter waves for a high speed wireless data transmission...... was proposed and research projects like IPHOBAC-NG were founded. The aim of the mentioned project is to employ novel RAUs featuring opticto-wireless and wireless-to-optic conversion with a speeds of 1-10Gbit/s for broadband wireless access and up to 3Gbit/s for mobile backhaul. The RAU proposed in this paper...

A wireless transmission system powered by an enzyme biofuel cell implanted in an orange.

Science.gov (United States)

MacVittie, Kevin; Conlon, Tyler; Katz, Evgeny

2015-12-01

A biofuel cell composed of catalytic electrodes made of "buckypaper" modified with PQQ-dependent glucose dehydrogenase and FAD-dependent fructose dehydrogenase on the anode and with laccase on the cathode was used to activate a wireless information transmission system. The cathode/anode pair was implanted in orange pulp extracting power from its content (glucose and fructose in the juice). The open circuit voltage, Voc, short circuit current density, jsc, and maximum power produced by the biofuel cell, Pmax, were found as ca. 0.6 V, ca. 0.33 mA·cm(-2) and 670 μW, respectively. The voltage produced by the biofuel cell was amplified with an energy harvesting circuit and applied to a wireless transmitter. The present study continues the research line where different implantable biofuel cells are used for the activation of electronic devices. The study emphasizes the biosensor and environmental monitoring applications of implantable biofuel cells harvesting power from natural sources, rather than their biomedical use. Copyright © 2014 Elsevier B.V. All rights reserved.

Modular high-voltage bias generator powered by dual-looped self-adaptive wireless power transmission.

Science.gov (United States)

Xie, Kai; Huang, An-Feng; Li, Xiao-Ping; Guo, Shi-Zhong; Zhang, Han-Lu

2015-04-01

We proposed a modular high-voltage (HV) bias generator powered by a novel transmitter-sharing inductive coupled wireless power transmission technology, aimed to extend the generator's flexibility and configurability. To solve the problems caused through an uncertain number of modules, a dual-looped self-adaptive control method is proposed that is capable of tracking resonance frequency while maintaining a relatively stable induction voltage for each HV module. The method combines a phase-locked loop and a current feedback loop, which ensures an accurate resonance state and a relatively constant boost ratio for each module, simplifying the architecture of the boost stage and improving the total efficiency. The prototype was built and tested. The input voltage drop of each module is less than 14% if the module number varies from 3 to 10; resonance tracking is completed within 60 ms. The efficiency of the coupling structure reaches up to 95%, whereas the total efficiency approaches 73% for a rated output. Furthermore, this technology can be used in various multi-load wireless power supply applications.

Evaluation of a microwave high-power reception-conversion array for wireless power transmission

Science.gov (United States)

Dickinson, R. M.

1975-01-01

Initial performance tests of a 24-sq m area array of rectenna elements are presented. The array is used as the receiving portion of a wireless microwave power transmission engineering verification test system. The transmitting antenna was located at a range of 1.54 km. Output dc voltage and power, input RF power, efficiency, and operating temperatures were obtained for a variety of dc load and RF incident power levels at 2388 MHz. Incident peak RF intensities of up to 170 mW/sq cm yielded up to 30.4 kW of dc output power. The highest derived collection-conversion efficiency of the array was greater than 80 percent.

Photonic techniques for sub-Terahertz wireless data transmission

DEFF Research Database (Denmark)

Tafur Monroy, Idelfonso

2015-01-01

Wireless data communication links with capacities beyond 100 Gbit/s will require operating at sub-Terahertz frequencies using a large bandpass bandwidth facing new engineering challenges. We review several implementation aspects by using photonic technologies. © 2015 OSA.......Wireless data communication links with capacities beyond 100 Gbit/s will require operating at sub-Terahertz frequencies using a large bandpass bandwidth facing new engineering challenges. We review several implementation aspects by using photonic technologies. © 2015 OSA....

Wireless transmission of power and information through one high frequency resonant AC link inverter for robot manipulator applications

International Nuclear Information System (INIS)

Kawamura, Atsuo; Ishioka, Kazuaki; Hirai, Junji.

1995-01-01

A contact-less decentralized power supply is proposed with communication capability through only one transformer. A prototype of wireless transmission system of power and information (WTPI system) was built, and the two axis position control for servo motors was achieved by transferring the power and signal through one rotatable high frequency transformer. The proposed concept can be applied for robotics and NC machines

10Gb/s Ultra-Wideband Wireless Transmission Based on Multi-Band Carrierless Amplitude Phase Modulation

DEFF Research Database (Denmark)

Puerta Ramírez, Rafael; Rommel, Simon; Vegas Olmos, Juan José

2016-01-01

In this paper, for the first time, a record UWB transmission of 10Gb/s is experimentally demonstrated employing a multi-band approach of carrierless amplitude phase modulation (MultiCAP). The proposed solution complies with the restrictions on the effective radiated power established by both...... the United States Federal Communications Commission and the European Electronic Communications Committee, achieving a BER below the limit for a 7% overhead FEC of 3.8 · 10−3 up to respective wireless distances of 3.5m and 2m....

Heterogeneous wireless/wireline optical access networks with the R-EAT as backend component

Science.gov (United States)

Hagedorn, Klaus; Gindera, Ralf; Stohr, Andreas; Jager, Dieter

2004-09-01

A heterogeneous wireless/wireline optical transmission link using a reflection type electroabsorption transceiver (R-EAT) is presented. Simultaneous transmission of full-duplex broadband wireless LAN (WLAN) channels and 1Gb/s base band data is experimentally demonstrated. The system link employs sub-carrier multiplexing (SCM) and two optical channels for full duplex transmission of various analog WLAN channels and downlink digital base band data. The developed link architecture is suitable for simultaneous transmission of broadband wireline and wireless signals, it enables the coexistence and interoperability between wireline and wireless access technologies. The developed R-EAT component employed in this wireline/wireless access system, features "single-chip-component" base stations in access networks with star type topology where only a single optical fiber is used for bidirectional optical transmission. The R-EAT can be used within the optical C-band (1530- 1560nm) and is suitable for (D)WDM networks. Bit error rate measurements demonstrate the capabilities of the R-EAT for 1Gb/s base band transmission. The analog performance for WLAN transmission is characterised by a spurious free dynamic range (SFDR) of more than 75dB and 90dB for uplink and downlink transmission, respectively. The link gain for uplink and downlink transmission is -42dB and -37dB, respectively. The demonstrates the analog performances of the R-EAT for being used in wireless access networks such as W-LAN.

Transmission techniques for emergent multicast and broadcast systems

CERN Document Server

da Silva, Mario Marques; Dinis, Rui; Souto, Nuno; Silva, Joao Carlos

2010-01-01

Describing efficient transmission schemes for broadband wireless systems, Transmission Techniques for Emergent Multicast and Broadcast Systems examines advances in transmission techniques and receiver designs capable of supporting the emergent wireless needs for multimedia broadcast and multicast service (MBMS) requirements. It summarizes the research and development taking place in wireless communications for multimedia MBMS and addresses the means to improved spectral efficiency to allow for increased user bit rate, as well as increased capacity of the digital cellular radio network.The text

Positive Coping: A Unique Characteristic to Pre-Hospital Emergency Personnel.

Science.gov (United States)

Ebadi, Abbas; Froutan, Razieh

2017-01-01

It is important to gain a thorough understanding of positive coping methods adopted by medical emergency personnel to manage stressful situations associated with accidents and emergencies. Thus, the purpose of this study was to gain a better understanding of positive coping strategies used by emergency medical service providers. This study was conducted using a qualitative content analysis method. The study participants included 28 pre-hospital emergency personnel selected from emergency medical service providers in bases located in different regions of the city of Mashhad, Iran, from April to November 2016. The purposive sampling method also was used in this study, which was continued until data saturation was reached. To collect the data, semistructured open interviews, observations, and field notes were used. Four categories and 10 subcategories were extracted from the data on the experiences of pre-hospital emergency personnel related to positive coping strategies. The four categories included work engagement, smart capability, positive feedback, and crisis pioneering. All the obtained categories had their own subcategories, which were determined based on their distinctly integrated properties. The results of this study show that positive coping consists of several concepts used by medical emergency personnel, management of stressful situations, and ultimately quality of pre-hospital clinical services. Given the fact that efficient methods such as positive coping can prevent debilitating stress in an individual, pre-hospital emergency authorities should seek to build and strengthen "positive coping" characteristics in pre-hospital medical emergency personnel to deal with accidents, emergencies, and injuries through adopting regular and dynamic policies.

A portable wireless power transmission system for video capsule endoscopes.

Science.gov (United States)

Shi, Yu; Yan, Guozheng; Zhu, Bingquan; Liu, Gang

2015-01-01

Wireless power transmission (WPT) technology can solve the energy shortage problem of the video capsule endoscope (VCE) powered by button batteries, but the fixed platform limited its clinical application. This paper presents a portable WPT system for VCE. Besides portability, power transfer efficiency and stability are considered as the main indexes of optimization design of the system, which consists of the transmitting coil structure, portable control box, operating frequency, magnetic core and winding of receiving coil. Upon the above principles, the correlation parameters are measured, compared and chosen. Finally, through experiments on the platform, the methods are tested and evaluated. In the gastrointestinal tract of small pig, the VCE is supplied with sufficient energy by the WPT system, and the energy conversion efficiency is 2.8%. The video obtained is clear with a resolution of 320×240 and a frame rate of 30 frames per second. The experiments verify the feasibility of design scheme, and further improvement direction is discussed.

Fully roll-to-roll gravure printed rectenna on plastic foils for wireless power transmission at 13.56 MHz.

Science.gov (United States)

Park, Hyejin; Kang, Hwiwon; Lee, Yonggil; Park, Yongsu; Noh, Jinsoo; Cho, Gyoujin

2012-08-31

Wireless power transmission to inexpensive and disposable smart electronic devices is one of the key issues for the realization of a ubiquitous society where sensor networks such as RFID tags, price tags, smart logos, signage and sensors could be fully interconnected and utilized by DC power of less than 0.3 W. This DC power can be provided by inductively coupled AC from a 13.56 MHz power transmitter through a rectenna, consisting of an antenna, a diode and a capacitor, which would be cheap to integrate with inexpensive smart electronic devices. To integrate the rectenna with a minimum cost, a roll-to-roll (R2R) gravure printing process has been considered to print the rectenna on plastic foils. In this paper, R2R gravure printing systems including printing condition and four different nanoparticle based inks will be reported to print the rectenna (antenna, diode and capacitor) on plastic foils at a printing speed of 8 m min(-1) and more than 90% device yield for a wireless power transmission of 0.3 W using a standard 13.56 MHz power transmitter.

3.125 Gb/s impulse radio ultra-wideband photonic generation and distribution Over a 50 km Fiber With Wireless Transmission

DEFF Research Database (Denmark)

Gibbon, Timothy Braidwood; Yu, Xianbin; Gamatham, Romeo

2010-01-01

A 3.125 Gb/s photonic impulse radio ultra-wideband signal is created using the incoherent optical field summation resulting from the cross gain modulation of an uncooled distributed feedback laser injected with an external cavity laser. After 50 km of fiber and wireless transmission over 2.9-3.3-m...

Source Coding for Wireless Distributed Microphones in Reverberant Environments

DEFF Research Database (Denmark)

Zahedi, Adel

2016-01-01

. However, it comes with the price of several challenges, including the limited power and bandwidth resources for wireless transmission of audio recordings. In such a setup, we study the problem of source coding for the compression of the audio recordings before the transmission in order to reduce the power...... consumption and/or transmission bandwidth by reduction in the transmission rates. Source coding for wireless microphones in reverberant environments has several special characteristics which make it more challenging in comparison with regular audio coding. The signals which are acquired by the microphones......Modern multimedia systems are more and more shifting toward distributed and networked structures. This includes audio systems, where networks of wireless distributed microphones are replacing the traditional microphone arrays. This allows for flexibility of placement and high spatial diversity...

Space-division-multiplexed transmission of 3x3 multiple-input multiple-output wireless signals over conventional graded-index multimode fiber.

Science.gov (United States)

Lei, Yi; Li, Jianqiang; Fan, Yuting; Yu, Dawei; Fu, Songnian; Yin, Feifei; Dai, Yitang; Xu, Kun

2016-12-12

In this paper, we experimentally demonstrate space-division-multiplexed (SDM) transmission of IEEE 802.11ac-compliant 3-spatial-stream WLAN signals over 3 spatial modes of conventional 50um graded-index (GI) multimode fiber (MMF) employing non-mode-selective 3D-waveguide photonic lantern. Two kinds of scenarios, including fiber-only transmission and fiber-wireless hybrid transmission, were investigated by measuring error vector magnitude (EVM) performance for each stream and condition number (CN) of the channel matrix. The experimental results show that, SDM-based MMF link could offer a CNwireless MIMO signals over existing in-building commercially-available MMFs with enormous cost-saving.

Performance evaluation of power transmission coils for powering endoscopic wireless capsules.

Science.gov (United States)

Basar, Md Rubel; Ahmad, Mohd Yazed; Cho, Jongman; Ibrahim, Fatimah

2015-01-01

This paper presents an analysis of H-field generated by a simple solenoid, pair of solenoids, pair of double-layer solenoids, segmented-solenoid, and Helmholtz power transmission coils (PTCs) to power an endoscopic wireless capsule (WC). The H-fields were computed using finite element analysis based on partial differential equations. Three parameters were considered in the analysis: i) the maximum level of H-field (Hmax) to which the patient's body would be exposed, ii) the minimum level of H-field (Hmin) effective for power transmission, and iii) uniformity of H-field. We validated our analysis by comparing the computed data with data measured from a fabricated Helmholtz PTC. This analysis disclosed that at the same excitation power, all the PTCs are able to transfer same amount of minimum usable power since they generated almost equal value of Hmin. The level of electromagnetic exposure and power transfer stability across all the PTCs would vary significantly which is mainly due to the different level of Hmax and H-field uniformity. The segmented solenoid PTC would cause the lowest exposure and this PTC can transfer the maximum amount of power. The Helmholtz PTC would be able to transfer the most stable power with a moderate level of exposure.

Wireless power and data transmission strategies for next-generation capsule endoscopes

International Nuclear Information System (INIS)

Puers, R; Carta, R; Thoné, J

2011-01-01

Capsular endoscopy is becoming increasingly popular as an alternative to traditional gastro-intestinal (GI) examination techniques. However, the breakthrough of these devices is hindered by the limited amount of power that can be stored in a tiny pill. Most commercial devices use two watch batteries that can only provide an average power of 25 mW for about 6 h, certainly not sufficient for advanced robotic features. A dedicated inductive powering system, operating at 1 MHz to limit the human body absorption, has been developed which was proven to support the transfer of over 300 mW. The system relies on a condensed set of orthogonal ferrite coils, embedded in the capsule, and an external unit based on a Helmholtz coil driven by a class E amplifier. Control data can be sent through the inductive link by modulating the power carrier, whereas a dedicated high data rate RF link is used to transfer the images from the capsule to the base station. Besides evaluating the compatibility with radio transmission, several demonstrators were assembled combining the wireless powering system with various locomotion strategies and LED illumination. This paper describes the design and implementation of the inductive powering system, its combination with data transmission techniques and the testing activity with other capsule-dedicated modules

Compact wideband CMOS receiver frontends for wireless communication

NARCIS (Netherlands)

Blaakmeer, S.C.

2010-01-01

Abstract Wireless communication is an integral part of our daily life, the mobile phone is an example of a very popular wireless communication device. A communication link consists of a transmitter, a receiver and the transmission medium, which air or vacuum for a wireless link. Part of the receiver

Pre-hospital physical activity status affects in-hospital course of elderly patients with acute myocardial infarction.

Science.gov (United States)

Miyamoto, Takamichi; Obayashi, Tohru; Hattori, Eijirou; Yamauchi, Yasuteru; Niwa, Akihiro; Isobe, Mitsuaki

2010-03-01

The clinical course of elderly patients with acute myocardial infarction (AMI) can sometimes unexpectedly result in an adverse outcome even when therapy appears to be successful. We suspect that specific factors may characterize this worsening of status during hospitalization. This study examines whether the pre-hospital physical activity status of the elderly treated with percutaneous coronary intervention (PCI) for AMI affects their in-hospital course. We studied 110 consecutive patients, aged 80 or older, who had undergone emergent PCI for AMI. Patients were divided into two groups based on clinical presentation: Better Killip class (Killip classes I and II) and Worse Killip class (Killip classes III and IV). Patients were also divided into two groups based on pre-hospital physical activity status, determined retrospectively by review of medical records: Good physical activity (n=57) comprising those able to go out alone independently and Poor physical activity comprising those mainly confined to home (n=53). The overall in-hospital mortality rate was 9.1% for the study population. The Worse Killip class group had a higher in-hospital mortality rate than the Better Killip class group (27.8% vs 5.4%, respectively; p=0.0102). In addition, the Poor physical activity group had a higher in-hospital mortality rate than the Good physical activity group (15.1% vs. 3.5%, respectively; p=0.047). These data suggest that pre-hospital physical activity status in elderly patients with AMI may affect in-hospital mortality as well as Killip class.

Effectiveness of compressed sensing and transmission in wireless sensor networks for structural health monitoring

Science.gov (United States)

Fujiwara, Takahiro; Uchiito, Haruki; Tokairin, Tomoya; Kawai, Hiroyuki

2017-04-01

Regarding Structural Health Monitoring (SHM) for seismic acceleration, Wireless Sensor Networks (WSN) is a promising tool for low-cost monitoring. Compressed sensing and transmission schemes have been drawing attention to achieve effective data collection in WSN. Especially, SHM systems installing massive nodes of WSN require efficient data transmission due to restricted communications capability. The dominant frequency band of seismic acceleration is occupied within 100 Hz or less. In addition, the response motions on upper floors of a structure are activated at a natural frequency, resulting in induced shaking at the specified narrow band. Focusing on the vibration characteristics of structures, we introduce data compression techniques for seismic acceleration monitoring in order to reduce the amount of transmission data. We carry out a compressed sensing and transmission scheme by band pass filtering for seismic acceleration data. The algorithm executes the discrete Fourier transform for the frequency domain and band path filtering for the compressed transmission. Assuming that the compressed data is transmitted through computer networks, restoration of the data is performed by the inverse Fourier transform in the receiving node. This paper discusses the evaluation of the compressed sensing for seismic acceleration by way of an average error. The results present the average error was 0.06 or less for the horizontal acceleration, in conditions where the acceleration was compressed into 1/32. Especially, the average error on the 4th floor achieved a small error of 0.02. Those results indicate that compressed sensing and transmission technique is effective to reduce the amount of data with maintaining the small average error.

An individual-based model of transmission of resistant bacteria in a veterinary teaching hospital.

Directory of Open Access Journals (Sweden)

Neeraj Suthar

Full Text Available Veterinary nosocomial infections caused by antibiotic resistant bacteria cause increased morbidity, higher cost and length of treatment and increased zoonotic risk because of the difficulty in treating them. In this study, an individual-based model was developed to investigate the effects of movements of canine patients among ten areas (transmission points within a veterinary teaching hospital, and the effects of these movements on transmission of antibiotic susceptible and resistant pathogens. The model simulates contamination of transmission points, healthcare workers, and patients as well as the effects of decontamination of transmission points, disinfection of healthcare workers, and antibiotic treatments of canine patients. The model was parameterized using data obtained from hospital records, information obtained by interviews with hospital staff, and the published literature. The model suggested that transmission resulting from contact with healthcare workers was common, and that certain transmission points (housing wards, diagnostics room, and the intensive care unit presented higher risk for transmission than others (lobby and surgery. Sensitivity analyses using a range of parameter values demonstrated that the risk of acquisition of colonization by resistant pathogens decreased with shorter patient hospital stays (P<0.0001, more frequent decontamination of transmission points and disinfection of healthcare workers (P<0.0001 and better compliance of healthcare workers with hygiene practices (P<0.0001. More frequent decontamination of heavily trafficked transmission points was especially effective at reducing transmission of the model pathogen.

Antiretroviral pre-exposure prophylaxis prevents vaginal transmission of HIV-1 in humanized BLT mice.

Directory of Open Access Journals (Sweden)

Paul W Denton

2008-01-01

Full Text Available Worldwide, vaginal transmission now accounts for more than half of newly acquired HIV-1 infections. Despite the urgency to develop and implement novel approaches capable of preventing HIV transmission, this process has been hindered by the lack of adequate small animal models for preclinical efficacy and safety testing. Given the importance of this route of transmission, we investigated the susceptibility of humanized mice to intravaginal HIV-1 infection.We show that the female reproductive tract of humanized bone marrow-liver-thymus (BLT mice is reconstituted with human CD4+ T and other relevant human cells, rendering these humanized mice susceptible to intravaginal infection by HIV-1. Effects of HIV-1 infection include CD4+ T cell depletion in gut-associated lymphoid tissue (GALT that closely mimics what is observed in HIV-1-infected humans. We also show that pre-exposure prophylaxis with antiretroviral drugs is a highly effective method for preventing vaginal HIV-1 transmission. Whereas 88% (7/8 of BLT mice inoculated vaginally with HIV-1 became infected, none of the animals (0/5 given pre-exposure prophylaxis of emtricitabine (FTC/tenofovir disoproxil fumarate (TDF showed evidence of infection (Chi square = 7.5, df = 1, p = 0.006.The fact that humanized BLT mice are susceptible to intravaginal infection makes this system an excellent candidate for preclinical evaluation of both microbicides and pre-exposure prophylactic regimens. The utility of humanized mice to study intravaginal HIV-1 transmission is particularly highlighted by the demonstration that pre-exposure prophylaxis can prevent intravaginal HIV-1 transmission in the BLT mouse model.

Architectures for radio over fiber transmission of high-quality video and data signals

DEFF Research Database (Denmark)

Lebedev, Alexander

with a constraint on complexity. For wireless personal area networks distribution, we explore the notion of joint optimization of physical layer parameters of a fiber-wireless link (optical power levels, wireless transmission distance) and the codec parameters (quantization, error-resilience tools) based...... on the peak signal-to-noise ratio as an objective video quality metric for compressed video transmission. Furthermore, we experimentally demonstrate uncompressed 1080i highdefinition video distribution in V-band (50–75 GHz) and W-band (75–110 GHz) fiber-wireless links achieving 3 m of wireless transmission...... efficient wired/wireless backhaul of picocell networks. Gigabit signal transmission is realized in combined fiber-wireless-fiber link enabling simultaneous backhaul of dense metropolitan and suburban areas. In this Thesis, we propose a technique to combat periodic chromatic dispersion-induced radio...

A consensus-based template for documenting and reporting in physician-staffed pre-hospital services

DEFF Research Database (Denmark)

Kruger, Andreas J; Lockey, David; Kurola, Jouni

2011-01-01

-staffed pre-hospital services in Europe. METHODS: Using predefined criteria, we recruited sixteen European experts in the field of pre-hospital care. These experts were guided through a four-step modified nominal group technique. The process was carried out using both e-mail-based communication and a plenary...... have established a core data set for documenting and reporting in physician-staffed pre-hospital services. We believe that this template could facilitate future studies within the field and facilitate standardised reporting and future shared research efforts in advanced pre-hospital care....

Performance enhancement of multi-core fiber transmission using real-time FPGA based pre-emphasis

DEFF Research Database (Denmark)

Hasanuzzaman, G. K.M.; Spolitis, Sandis; Salgals, T.

2017-01-01

We experimentally demonstrate pre-emphasis based performance for a 2 km long 7-core multicore fiber link. Simultaneous transmission below the FEC threshold is achievable for all cores by using signal equalization in a FPGA.......We experimentally demonstrate pre-emphasis based performance for a 2 km long 7-core multicore fiber link. Simultaneous transmission below the FEC threshold is achievable for all cores by using signal equalization in a FPGA....

Design and Implementation of Dual-Mode Wireless Video Monitoring System

Directory of Open Access Journals (Sweden)

BAO Song-Jian

2014-10-01

Full Text Available Dual-mode wireless video transmission has two major problems. Firstly, one is time delay difference bringing about asynchronous reception decoding frame error phenomenon; secondly, dual-mode network bandwidth inconformity causes scheduling problem. In order to solve above two problems, a kind of TD-SCDMA/CDMA20001x dual-mode wireless video transmission design method is proposed. For the solution of decoding frame error phenomenon, the design puts forward adding frame identification and packet preprocessing at the sending and synchronizing combination at the receiving end. For the solution of scheduling problem, the wireless communication channel cooperative work and video data transmission scheduling management algorithm is proposed in the design.

Operating Protocol and Networking Issues of a Telemedicine Platform Integrating from Wireless Home Sensors to the Hospital Information System

Directory of Open Access Journals (Sweden)

Massimiliano Donati

2013-01-01

Full Text Available Chronic heart failure (CHF is among the major causes of hospitalization for elderly citizens. Its considerable impact on patient quality of life, the resources congestion, and the related costs can be efficiently mitigated using remote wireless biosensors networks placed at patient home, able to communicate in secure way over the public Internet with the cardiology departmental Hospital Information System (HIS. In this way, physicians can monitor the situation of several patients at distance and quickly realize and act alterations in vital parameters. In this scenario, the Health@Home (H@H platform is conceived. The pool of Bluetooth sensors enables patients to daily collect vital signs at home in noninvasive fashion. A home gateway receives and processes all signals before sending them to a server node in charge of interfacing with the usual HIS. The novel concept of operating protocol (OP represents a list of actions, remotely configurable, that the domestic network has to follow (required measurements, transmissions, comparisons with personalized thresholds, etc.. The first medical tests on 30 patients (1 month allowed to verify the model, both from the patient and the medical perspective. The main evaluation metrics were usability, flexibility, and reliability of the communication from sensors to HIS.

Expected Transmission Energy Route Metric for Wireless Mesh Senor Networks

Directory of Open Access Journals (Sweden)

YanLiang Jin

2011-01-01

Full Text Available Mesh is a network topology that achieves high throughput and stable intercommunication. With great potential, it is expected to be the key architecture of future networks. Wireless sensor networks are an active research area with numerous workshops and conferences arranged each year. The overall performance of a WSN highly depends on the energy consumption of the network. This paper designs a new routing metric for wireless mesh sensor networks. Results from simulation experiments reveal that the new metric algorithm improves the energy balance of the whole network and extends the lifetime of wireless mesh sensor networks (WMSNs.

Electrostatic Vibration Energy Harvester Pre-charged Wirelessly at 2.45 GHz

Science.gov (United States)

Saddi, Z.; Takhedmit, H.; Karami, A.; Basset, P.; Cirio, L.

2016-11-01

This paper reports the design, fabrication and experiments of an electrostatic vibration harvester (e-VEH), pre-charged wirelessly for the first time by using an electromagnetic waves harvester at 2.4 GHz. The rectenna uses the Cockcroft-Walton voltage doubler rectifier. It is designed and optimized to operate at low power densities and provides high voltage levels: 0.5 V at 0.5 μW/cm2 and 0.8 V at 1 μW/cm2 The e-VEH uses the Bennet doubler as conditioning circuit. Experiments show 23 V voltage across the transducer terminal when the harvester is excited at 25 Hz by 1.5 g of external acceleration. An accumulated energy of 275 μJ and a maximum power of 0.4 μW are available for the load.

Electrostatic Vibration Energy Harvester Pre-charged Wirelessly at 2.45 GHz

International Nuclear Information System (INIS)

Saddi, Z.; Takhedmit, H.; Basset, P.; Cirio, L.; Karami, A.

2016-01-01

This paper reports the design, fabrication and experiments of an electrostatic vibration harvester (e-VEH), pre-charged wirelessly for the first time by using an electromagnetic waves harvester at 2.4 GHz. The rectenna uses the Cockcroft-Walton voltage doubler rectifier. It is designed and optimized to operate at low power densities and provides high voltage levels: 0.5 V at 0.5 μW/cm 2 and 0.8 V at 1 μW/cm 2 The e-VEH uses the Bennet doubler as conditioning circuit. Experiments show 23 V voltage across the transducer terminal when the harvester is excited at 25 Hz by 1.5 g of external acceleration. An accumulated energy of 275 μJ and a maximum power of 0.4 μW are available for the load. (paper)

Pre-eclampsia: Factores de riesgo. Estudio en el Hospital Nacional Cayetano Heredia.

OpenAIRE

Salviz Salhuana, Manuel; Cordero Muñoz, Luis; Saona Ugarte, Pedro

1996-01-01

Objetivo: El objetivo fue evaluar los factores de riesgo asociados a pre-eclampsia en nuestro hospital. Material y métodos: Se realizó un estudio prospectivo, de tipo caso-control concurrente en 88 pacientes con pre-eclampsia e igual número de controles. El trabajo se llevó a cabo en el Servicio de Obstetricia del Hospital Nacional Cayetano Heredia entre los meses de marzo a agosto de 1993. Resultados: Los factores asociados a pre-eclampsia fueron el antecedente previo a pre-eclampsia (OR:17)...

Self-tuning wireless power transmission scheme based on on-line scattering parameters measurement and two-side power matching.

Science.gov (United States)

Luo, Yanting; Yang, Yongmin; Chen, Zhongsheng

2014-04-10

Sub-resonances often happen in wireless power transmission (WPT) systems using coupled magnetic resonances (CMR) due to environmental changes, coil movements or component degradations, which is a serious challenge for high efficiency power transmission. Thus self-tuning is very significant to keep WPT systems following strongly magnetic resonant conditions in practice. Traditional coupled-mode ways is difficult to solve this problem. In this paper a two-port power wave model is presented, where power matching and the overall systemic power transmission efficiency are firstly defined by scattering (S) parameters. Then we propose a novel self-tuning scheme based on on-line S parameters measurements and two-side power matching. Experimental results testify the feasibility of the proposed method. These findings suggest that the proposed method is much potential to develop strongly self-adaptive WPT systems with CMR.

Bidirectional 3.125 Gbps downstream / 2 Gbps upstream impulse radio ultrawide-band (UWB) over combined fiber and wireless link

DEFF Research Database (Denmark)

Jensen, Jesper Bevensee; Gibbon, Timothy Braidwood; Yu, Xianbin

2010-01-01

We demonstrate bidirectional fiber and wireless transmission of impulse radio ultra-wideband at 3.125 Gbps downstream and 2 Gbps upstream. After transmission over 50 km fiber and 1.85 m wireless link both signals are recovered without errors.......We demonstrate bidirectional fiber and wireless transmission of impulse radio ultra-wideband at 3.125 Gbps downstream and 2 Gbps upstream. After transmission over 50 km fiber and 1.85 m wireless link both signals are recovered without errors....

Application for vibration monitoring of aspheric surface machining based on wireless sensor networks

Science.gov (United States)

Han, Chun Guang; Guo, Yin Biao; Jiang, Chen

2010-05-01

Any kinds of tiny vibration of machine tool parts will have a great influence on surface quality of the workpiece at ultra-precise machining process of aspheric surface. At present the major way for decreasing influence of vibration is machining compensation technology. Therefore it is important for machining compensation control to acquire and transmit these vibration signals effectively. This paper presents a vibration monitoring system of aspheric surface machining machine tool based on wireless sensor networks (WSN). Some key issues of wireless sensor networks for vibration monitoring system of aspheric surface machining are discussed. The reliability of data transmission, network communication protocol and synchronization mechanism of wireless sensor networks are studied for the vibration monitoring system. The proposed system achieves multi-sensors vibration monitoring involving the grinding wheel, the workpiece and the workbench spindle. The wireless transmission of vibration signals is achieved by the combination with vibration sensor nodes and wireless network. In this paper, these vibration sensor nodes are developed. An experimental platform is structured which employs wireless sensor networks to the vibration monitoring system in order to test acquisition and wireless transmission of vibration signal. The test results show that the proposed system can achieve vibration data transmission effectively and reliability and meet the monitoring requirements of aspheric surface machining machine tool.

Pervasive wireless environments

CERN Document Server

Yang, Jie; Trappe, Wade; Cheng, Jerry

2014-01-01

This Springer Brief provides a new approach to prevent user spoofing by using the physical properties associated with wireless transmissions to detect the presence of user spoofing. The most common method, applying cryptographic authentication, requires additional management and computational power that cannot be deployed consistently. The authors present the new approach by offering a summary of the recent research and exploring the benefits and potential challenges of this method. This brief discusses the feasibility of launching user spoofing attacks and their impact on the wireless and sen

Nosocomial Transmission of C. difficile in English Hospitals from Patients with Symptomatic Infection

Science.gov (United States)

van Kleef, Esther; Gasparrini, Antonio; Guy, Rebecca; Cookson, Barry; Hope, Russell; Jit, Mark; Robotham, Julie V.; Deeny, Sarah R.; Edmunds, W. John

2014-01-01

Background Recent evidence suggests that less than one-quarter of patients with symptomatic nosocomial Clostridium difficile infections (CDI) are linked to other in-patients. However, this evidence was limited to one geographic area. We aimed to investigate the level of symptomatic CDI transmission in hospitals located across England from 2008 to 2012. Methods A generalized additive mixed-effects Poisson model was fitted to English hospital-surveillance data. After adjusting for seasonal fluctuations and between-hospital variation in reported CDI over time, possible clustering (transmission between symptomatic in-patients) of CDI cases was identified. We hypothesised that a temporal proximity would be reflected in the degree of correlation between in-hospital CDI cases per week. This correlation was modelled through a latent autoregressive structure of order 1 (AR(1)). Findings Forty-six hospitals (33 general, seven specialist, and six teaching hospitals) located in all English regions met our criteria. In total, 12,717 CDI cases were identified; seventy-five per cent of these occurred >48 hours after admission. There were slight increases in reports during winter months. We found a low, but statistically significant, correlation between successive weekly CDI case incidences (phi = 0.029, 95%CI: 0.009–0.049). This correlation was five times stronger in a subgroup analysis restricted to teaching hospitals (phi = 0.104, 95%CI: 0.048–0.159). Conclusions The results suggest that symptomatic patient-to-patient transmission has been a source of CDI-acquisition in English hospitals in recent years, and that this might be a more important transmission route in teaching hospitals. Nonetheless, the weak correlation indicates that, in line with recent evidence, symptomatic cases might not be the primary source of nosocomial CDI in England. PMID:24932484

Low-crosstalk full-duplex all-optical indoor wireless transmission with carrier recovery

NARCIS (Netherlands)

Oh, C.W.; Cao, Z.; Mekonnen, K.A.; Tangdiongga, E.; Koonen, A.M.J.

2017-01-01

We propose and demonstrate a novel bi-directional free-space (FS) optical wireless communication system for indoor wireless networks. A 2-D infrared beam-steered system supporting full-duplex communication of at least 10 Gb/s capacity per wireless terminal with simple NRZ-OOK modulation format is

Risk assessment of pre-hospital trauma airway management by anaesthesiologists using the predictive Bayesian approach

Directory of Open Access Journals (Sweden)

Nakstad Anders R

2010-04-01

Full Text Available Abstract Introduction Endotracheal intubation (ETI has been considered an essential part of pre-hospital advanced life support. Pre-hospital ETI, however, is a complex intervention also for airway specialist like anaesthesiologists working as pre-hospital emergency physicians. We therefore wanted to investigate the quality of pre-hospital airway management by anaesthesiologists in severely traumatised patients and identify possible areas for improvement. Method We performed a risk assessment according to the predictive Bayesian approach, in a typical anaesthesiologist-manned Norwegian helicopter emergency medical service (HEMS. The main focus of the risk assessment was the event where a patient arrives in the emergency department without ETI despite a pre-hospital indication for it. Results In the risk assessment, we assigned a high probability (29% for the event assessed, that a patient arrives without ETI despite a pre-hospital indication. However, several uncertainty factors in the risk assessment were identified related to data quality, indications for use of ETI, patient outcome and need for special training of ETI providers. Conclusion Our risk assessment indicated a high probability for trauma patients with an indication for pre-hospital ETI not receiving it in the studied HEMS. The uncertainty factors identified in the assessment should be further investigated to better understand the problem assessed and consequences for the patients. Better quality of pre-hospital airway management data could contribute to a reduction of these uncertainties.

Energy Efficient Four Level Cooperative Opportunistic Communication for Wireless Personal Area Networks (WPAN)

DEFF Research Database (Denmark)

Rohokale, Vandana M.; Inamdar, Sandeep; Prasad, Neeli R.

2013-01-01

For wireless sensor networks (WSN),energy is a scarce resource. Due to limited battery resources, the energy consumption is the critical issue for the transmission as well as reception of the signals in the wireless communication. WSNs are infrastructure-less shared network demanding more energy...... consumption due to collaborative transmissions. This paper proposes a new cooperative opportunistic four level model for IEEE 802.15.4 Wireless Personal Area Network (WPAN).The average per node energy consumption is observed merely about 0.17mJ for the cooperative wireless communication which proves...... the proposed mechanism to be energy efficient. This paper further proposes four levels of cooperative data transmission from source to destination to improve network coverage with energy efficiency....

Wireless data link for FBTR

International Nuclear Information System (INIS)

Sundararajan, M.K.; Prabhakara Rao, G.; Ilango Sambasivan, S.; Swaminathan, P.; Ramakrishna, P.V.

2004-01-01

This paper deals with the design and development of a wireless data link for transmission of block pile signals at the Fast Breeder Test Reactor (FBTR) of Indira Gandhi Center for Atomic Research (IGCAR). This link is to establish wireless connectivity, typically at RS232C rates, over distances of the order of 50 m, and is expected to operate under electrically hostile conditions. (author)

Nuclear data transmission based on zigbee

International Nuclear Information System (INIS)

Cui Yan; Fang Fang; Chen Wei; Jiang Zancheng

2007-01-01

Zigbee, a new wireless communication protocol, which is an important technology supporting wireless sensor networks. We introduce a solution of nuclear data transmission based on zigbee, the cc2420 build up the core of the data acquisition module and the wireless transceive module, and realized remote monitor and nuclear data quickly analysis. (authors)

Data transmission techniques for short-range optical fiber and wireless communication links

DEFF Research Database (Denmark)

Pham, Tien Thang

The research work described in this thesis is devoted to experimental investigation of techniques for cost-effective high-speed optical communications supporting both wired and wireless services. The main contributions of this thesis have expanded the state-of-the-art in two main areas: high......-speed optical/wireless integration and advanced modulation formats for intensity modulation with direct detection (IM/DD) optical systems. Regarding optical/wireless integration, this thesis focuses on integration of broadband ultra-wide band (UWB) and 60-GHz band wireless systems into optical fiber access...... networks to distribute wireless services in personal area networks (PANs). Photonic technologies to generate and distribute gigabit UWB and 60-GHz-band signals are proposed and demonstrated. Two novel methods are proposed and demonstrated to optically generate Federal Communications Commission (FCC...

Voice Quality Estimation in Wireless Networks

Directory of Open Access Journals (Sweden)

Petr Zach

2015-01-01

Full Text Available This article deals with the impact of Wireless (Wi-Fi networks on the perceived quality of voice services. The Quality of Service (QoS metrics must be monitored in the computer network during the voice data transmission to ensure proper voice service quality the end-user has paid for, especially in the wireless networks. In addition to the QoS, research area called Quality of Experience (QoE provides metrics and methods for quality evaluation from the end-user’s perspective. This article focuses on a QoE estimation of Voice over IP (VoIP calls in the wireless networks using network simulator. Results contribute to voice quality estimation based on characteristics of the wireless network and location of a wireless client.

Effect of the ratio of radial gap to radius of the coils on the transmission efficiency of wireless power transfer via coupled magnetic resonances

Science.gov (United States)

Gao, Pengfei; Tian, Zijian; Wang, Xuqi; Wu, Jun; Gui, Weifeng

2018-03-01

Wireless power transfer (WPT) via coupled magnetic resonance is a promising technology to be applied in many fields. In general, there will be a radial gap in practical application, and some special application environments need to limit the radius of the coils. Therefore, in this paper, considering the comprehensive analysis of the radial gap and the radius of the coils, the concept of the ratio of radial gap to the radius of the coils was proposed. Based on the circuit theory, the formula between the ratio and transmission efficiency of WPT was deduced, and the effects of the ratio on the transmission efficiency were studied respectively at different axial distances. Simulation experiments were carried out and the results not only demonstrate the influence law of the ratio on transmission efficiency, but also validate the value of the ratio which the axial distance has the greatest effect on the transmission efficiency. Besides, the results shows the relationship between the effect of the ratio on the efficiency and the effect of the axial distance on the efficiency. The experimental results show that the theoretical analysis is correct, thus providing an useful theoretical reference for the design and further research on the wireless power transfer system in complicated environment.

Effect of the ratio of radial gap to radius of the coils on the transmission efficiency of wireless power transfer via coupled magnetic resonances

Directory of Open Access Journals (Sweden)

Pengfei Gao

2018-03-01

Full Text Available Wireless power transfer (WPT via coupled magnetic resonance is a promising technology to be applied in many fields. In general, there will be a radial gap in practical application, and some special application environments need to limit the radius of the coils. Therefore, in this paper, considering the comprehensive analysis of the radial gap and the radius of the coils, the concept of the ratio of radial gap to the radius of the coils was proposed. Based on the circuit theory, the formula between the ratio and transmission efficiency of WPT was deduced, and the effects of the ratio on the transmission efficiency were studied respectively at different axial distances. Simulation experiments were carried out and the results not only demonstrate the influence law of the ratio on transmission efficiency, but also validate the value of the ratio which the axial distance has the greatest effect on the transmission efficiency. Besides, the results shows the relationship between the effect of the ratio on the efficiency and the effect of the axial distance on the efficiency. The experimental results show that the theoretical analysis is correct, thus providing an useful theoretical reference for the design and further research on the wireless power transfer system in complicated environment.

Nosocomial transmission of community-associated methicillin-resistant Staphylococcus aureus in Danish Hospitals

DEFF Research Database (Denmark)

Hetem, David J; Westh, Henrik; Boye, Kit

2012-01-01

exposure. Despite obvious epidemiological differences, it is unknown whether differences in nosocomial transmissibility exist. We have, therefore, quantified the transmissibility, expressed by the single admission reproduction number (R(A)), of CA-MRSA and HA-MRSA in hospital settings in Denmark....

Relative localization in wireless sensor networks for measurement of electric fields under HVDC transmission lines.

Science.gov (United States)

Cui, Yong; Wang, Qiusheng; Yuan, Haiwen; Song, Xiao; Hu, Xuemin; Zhao, Luxing

2015-02-04

In the wireless sensor networks (WSNs) for electric field measurement system under the High-Voltage Direct Current (HVDC) transmission lines, it is necessary to obtain the electric field distribution with multiple sensors. The location information of each sensor is essential to the correct analysis of measurement results. Compared with the existing approach which gathers the location information by manually labelling sensors during deployment, the automatic localization can reduce the workload and improve the measurement efficiency. A novel and practical range-free localization algorithm for the localization of one-dimensional linear topology wireless networks in the electric field measurement system is presented. The algorithm utilizes unknown nodes' neighbor lists based on the Received Signal Strength Indicator (RSSI) values to determine the relative locations of nodes. The algorithm is able to handle the exceptional situation of the output permutation which can effectively improve the accuracy of localization. The performance of this algorithm under real circumstances has been evaluated through several experiments with different numbers of nodes and different node deployments in the China State Grid HVDC test base. Results show that the proposed algorithm achieves an accuracy of over 96% under different conditions.

Relative Localization in Wireless Sensor Networks for Measurement of Electric Fields under HVDC Transmission Lines

Directory of Open Access Journals (Sweden)

Yong Cui

2015-02-01

Full Text Available In the wireless sensor networks (WSNs for electric field measurement system under the High-Voltage Direct Current (HVDC transmission lines, it is necessary to obtain the electric field distribution with multiple sensors. The location information of each sensor is essential to the correct analysis of measurement results. Compared with the existing approach which gathers the location information by manually labelling sensors during deployment, the automatic localization can reduce the workload and improve the measurement efficiency. A novel and practical range-free localization algorithm for the localization of one-dimensional linear topology wireless networks in the electric field measurement system is presented. The algorithm utilizes unknown nodes’ neighbor lists based on the Received Signal Strength Indicator (RSSI values to determine the relative locations of nodes. The algorithm is able to handle the exceptional situation of the output permutation which can effectively improve the accuracy of localization. The performance of this algorithm under real circumstances has been evaluated through several experiments with different numbers of nodes and different node deployments in the China State Grid HVDC test base. Results show that the proposed algorithm achieves an accuracy of over 96% under different conditions.

Cooperative Diversity in Wireless Networks

Directory of Open Access Journals (Sweden)

A. Mahmood

2010-01-01

Full Text Available Transmit Diversity is an effective methodology for improving the quality and reliability of a wireless network by reducingthe effects of fading. As majority of the wireless devices (i.e. mobile handsets, etc are limited to only one antenna, especiallydue to hardware constraints, size and cost factors; cooperative communication can be utilized in order to generatetransmit diversity [1]. This enables single antenna wireless devices to share their antennas during transmission in such amanner that creates a virtual MIMO (multiple-input and multiple-output system [2] [3]. In this paper, we will analyze therecent developments and trends in this promising area of wireless Ad hoc networks. The article will also discuss variousmain cooperative signaling methods and will also observe their performance.

Dynamic Session-Key Generation for Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Chen Chin-Ling

2008-01-01

Full Text Available Abstract Recently, wireless sensor networks have been used extensively in different domains. For example, if the wireless sensor node of a wireless sensor network is distributed in an insecure area, a secret key must be used to protect the transmission between the sensor nodes. Most of the existing methods consist of preselecting keys from a key pool and forming a key chain. Then, the sensor nodes make use of the key chain to encrypt the data. However, while the secret key is being transmitted, it can easily be exposed during transmission. We propose a dynamic key management protocol, which can improve the security of the key juxtaposed to existing methods. Additionally, the dynamic update of the key can lower the probability of the key to being guessed correctly. In addition, with the new protocol, attacks on the wireless sensor network can be avoided.

Dynamic Session-Key Generation for Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Cheng-Ta Li

2008-09-01

Full Text Available Recently, wireless sensor networks have been used extensively in different domains. For example, if the wireless sensor node of a wireless sensor network is distributed in an insecure area, a secret key must be used to protect the transmission between the sensor nodes. Most of the existing methods consist of preselecting m keys from a key pool and forming a key chain. Then, the sensor nodes make use of the key chain to encrypt the data. However, while the secret key is being transmitted, it can easily be exposed during transmission. We propose a dynamic key management protocol, which can improve the security of the key juxtaposed to existing methods. Additionally, the dynamic update of the key can lower the probability of the key to being guessed correctly. In addition, with the new protocol, attacks on the wireless sensor network can be avoided.

Power consumption analysis of constant bit rate data transmission over 3G mobile wireless networks

DEFF Research Database (Denmark)

Wang, Le; Ukhanova, Ann; Belyaev, Evgeny

2011-01-01

This paper presents the analysis of the power consumption of data transmission with constant bit rate over 3G mobile wireless networks. Our work includes the description of the transition state machine in 3G networks, followed by the detailed energy consumption analysis and measurement results...... of the radio link power consumption. Based on these description and analysis, we propose power consumption model. The power model was evaluated on the smartphone Nokia N900, which follows a 3GPP Release 5 and 6 supporting HSDPA/HSPA data bearers. Further we propose method of parameters selection for 3GPP...... transition state machine that allows to decrease power consumption on the mobile device....

Bidirectional fiber-wireless and fiber-IVLLC integrated system based on polarization-orthogonal modulation scheme.

Science.gov (United States)

Lu, Hai-Han; Li, Chung-Yi; Chen, Hwan-Wei; Ho, Chun-Ming; Cheng, Ming-Te; Huang, Sheng-Jhe; Yang, Zih-Yi; Lin, Xin-Yao

2016-07-25

A bidirectional fiber-wireless and fiber-invisible laser light communication (IVLLC) integrated system that employs polarization-orthogonal modulation scheme for hybrid cable television (CATV)/microwave (MW)/millimeter-wave (MMW)/baseband (BB) signal transmission is proposed and demonstrated. To our knowledge, it is the first one that adopts a polarization-orthogonal modulation scheme in a bidirectional fiber-wireless and fiber-IVLLC integrated system with hybrid CATV/MW/MMW/BB signal. For downlink transmission, carrier-to-noise ratio (CNR), composite second-order (CSO), composite triple-beat (CTB), and bit error rate (BER) perform well over 40-km single-mode fiber (SMF) and 10-m RF/50-m optical wireless transport scenarios. For uplink transmission, good BER performance is obtained over 40-km SMF and 50-m optical wireless transport scenario. Such a bidirectional fiber-wireless and fiber-IVLLC integrated system for hybrid CATV/MW/MMW/BB signal transmission will be an attractive alternative for providing broadband integrated services, including CATV, Internet, and telecommunication services. It is shown to be a prominent one to present the advancements for the convergence of fiber backbone and RF/optical wireless feeder.

Wireless communications resource management

CERN Document Server

Lee, B; Seo, H

2009-01-01

Wireless technologies continue to evolve to address the insatiable demand for faster response times, larger bandwidth, and reliable transmission. Yet as the industry moves toward the development of post 3G systems, engineers have consumed all the affordable physical layer technologies discovered to date. This has necessitated more intelligent and optimized utilization of available wireless resources. Wireless Communications Resource Managem ent, Lee, Park, and Seo cover all aspects of this critical topic, from the preliminary concepts and mathematical tools to detailed descriptions of all the resource management techniques. Readers will be able to more effectively leverage limited spectrum and maximize device battery power, as well as address channel loss, shadowing, and multipath fading phenomena.

Adaptive Control of the Packet Transmission Period with Solar Energy Harvesting Prediction in Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Kideok Kwon

2015-04-01

Full Text Available A number of research works has studied packet scheduling policies in energy scavenging wireless sensor networks, based on the predicted amount of harvested energy. Most of them aim to achieve energy neutrality, which means that an embedded system can operate perpetually while meeting application requirements. Unlike other renewable energy sources, solar energy has the feature of distinct periodicity in the amount of harvested energy over a day. Using this feature, this paper proposes a packet transmission control policy that can enhance the network performance while keeping sensor nodes alive. Furthermore, this paper suggests a novel solar energy prediction method that exploits the relation between cloudiness and solar radiation. The experimental results and analyses show that the proposed packet transmission policy outperforms others in terms of the deadline miss rate and data throughput. Furthermore, the proposed solar energy prediction method can predict more accurately than others by 6.92%.

Adaptive control of the packet transmission period with solar energy harvesting prediction in wireless sensor networks.

Science.gov (United States)

Kwon, Kideok; Yang, Jihoon; Yoo, Younghwan

2015-04-24

A number of research works has studied packet scheduling policies in energy scavenging wireless sensor networks, based on the predicted amount of harvested energy. Most of them aim to achieve energy neutrality, which means that an embedded system can operate perpetually while meeting application requirements. Unlike other renewable energy sources, solar energy has the feature of distinct periodicity in the amount of harvested energy over a day. Using this feature, this paper proposes a packet transmission control policy that can enhance the network performance while keeping sensor nodes alive. Furthermore, this paper suggests a novel solar energy prediction method that exploits the relation between cloudiness and solar radiation. The experimental results and analyses show that the proposed packet transmission policy outperforms others in terms of the deadline miss rate and data throughput. Furthermore, the proposed solar energy prediction method can predict more accurately than others by 6.92%.

Seals monitoring systems using wireless communications

International Nuclear Information System (INIS)

Hermand, Guillaume; Bertrand, Johan; Farhoud, Radwan; Suzuki, Kei; ETO, Jiro; Tanabe, Hiromi; Takamura, Hisashi; Suyama, Yasuhiro

2012-01-01

Document available in extended abstract form only. Wireless monitoring based on electromagnetic waves is a promising application for deep geological nuclear waste repositories. It should allow data transmission without installing wires across the various seals (disposal cell plugs, gallery plugs, shaft plugs). Developments of the wireless system (e.g. transmitter and receiver) are in progress in order to fit the repository requirements. A common research program has been elaborated by RWMC and Andra. The present work aims at developing the wireless monitoring technology to intermediate level waste (ILW) disposal facilities concept. In this concept, ILW packages will be emplaced in disposal cells with concrete liner. After the operational phase, the cells will be backfilled with sealing material. In practice, this work demonstrates the feasibility of adapting and optimizing the wireless transmission system for specific repository cases. After preliminary transmission studies, it was decided to make a representative test in situ of a wireless transmission through the clay from a sealed side to an accessible side of the repository. In order to reduce the attenuation of magnetic flux caused by steel components between the transmitter and the receiver, the receiving antenna is installed in a dedicated borehole (drilled from the accessible side). Two types of reception antennas have been designed. According to its coil orientation, type A antenna measures the electromagnetic wave perpendicular to the borehole axis. On the other hand, type B antenna with a coil set in-line with the tubular casing, measures the electromagnetic wave parallel to the borehole axis. The outside cylinder (pressure tight case) is made of PVC considering the attenuation of electromagnetic flux. According to the direction of electromagnetic flux and position of the boreholes in the final repository design, type A or type B will be chosen. For the 'representative' test, a borehole, TSF1002 has been

The opportunistic transmission of wireless worms between mobile devices

Science.gov (United States)

Rhodes, C. J.; Nekovee, M.

2008-12-01

The ubiquity of portable wireless-enabled computing and communications devices has stimulated the emergence of malicious codes (wireless worms) that are capable of spreading between spatially proximal devices. The potential exists for worms to be opportunistically transmitted between devices as they move around, so human mobility patterns will have an impact on epidemic spread. The scenario we address in this paper is proximity attacks from fleetingly in-contact wireless devices with short-range communication range, such as Bluetooth-enabled smart phones. An individual-based model of mobile devices is introduced and the effect of population characteristics and device behaviour on the outbreak dynamics is investigated. The model uses straight-line motion to achieve population, though it is recognised that this is a highly simplified representation of human mobility patterns. We show that the contact rate can be derived from the underlying mobility model and, through extensive simulation, that mass-action epidemic models remain applicable to worm spreading in the low density regime studied here. The model gives useful analytical expressions against which more refined simulations of worm spread can be developed and tested.

Energy management in wireless cellular and ad-hoc networks

CERN Document Server

Imran, Muhammad; Qaraqe, Khalid; Alouini, Mohamed-Slim; Vasilakos, Athanasios

2016-01-01

This book investigates energy management approaches for energy efficient or energy-centric system design and architecture and presents end-to-end energy management in the recent heterogeneous-type wireless network medium. It also considers energy management in wireless sensor and mesh networks by exploiting energy efficient transmission techniques and protocols. and explores energy management in emerging applications, services and engineering to be facilitated with 5G networks such as WBANs, VANETS and Cognitive networks. A special focus of the book is on the examination of the energy management practices in emerging wireless cellular and ad hoc networks. Considering the broad scope of energy management in wireless cellular and ad hoc networks, this book is organized into six sections covering range of Energy efficient systems and architectures; Energy efficient transmission and techniques; Energy efficient applications and services. .

The pre-hospital administration of tranexamic acid to patients with multiple injuries and its effects on rotational thrombelastometry: a prospective observational study in pre-hospital emergency medicine.

Science.gov (United States)

Kunze-Szikszay, Nils; Krack, Lennart A; Wildenauer, Pauline; Wand, Saskia; Heyne, Tim; Walliser, Karoline; Spering, Christopher; Bauer, Martin; Quintel, Michael; Roessler, Markus

2016-10-10

Hyperfibrinolysis (HF) is a major contributor to coagulopathy and mortality in trauma patients. This study investigated (i) the rate of HF during the pre-hospital management of patients with multiple injuries and (ii) the effects of pre-hospital tranexamic acid (TxA) administration on the coagulation system. From 27 trauma patients with pre-hospital an estimated injury severity score (ISS) ≥16 points blood was obtained at the scene and on admission to the emergency department (ED). All patients received 1 g of TxA after the first blood sample was taken. Rotational thrombelastometry (ROTEM) was performed for both blood samples, and the results were compared. HF was defined as a maximum lysis (ML) >15 % in EXTEM. The median (min-max) ISS was 17 points (4-50 points). Four patients (15 %) had HF diagnosed via ROTEM at the scene, and 2 patients (7.5 %) had HF diagnosed via ROTEM on admission to the ED. The median ML before TxA administration was 11 % (3-99 %) vs. 10 % after TxA administration (4-18 %; p > 0.05). TxA was administered 37 min (10-85 min) before ED arrival. The ROTEM results before and after TxA administration did not significantly differ. No adverse drug reactions were observed after TxA administration. HF can be present in severely injured patients during pre-hospital care. Antifibrinolytic therapy administered at the scene is a significant time saver. Even in milder trauma fibrinogen can be decreased to critically low levels. Early administration of TxA cannot reverse or entirely stop this decrease. The pre-hospital use of TxA should be considered for severely injured patients to prevent the worsening of trauma-induced coagulopathy and unnecessarily high fibrinogen consumption. ClinicalTrials.gov ID NCT01938768 (Registered 5 September 2013).

Pre-hospital transfusion of plasma in hemorrhaging trauma patients independently improves hemostatic competence and acidosis

DEFF Research Database (Denmark)

Henriksen, Hanne Herborg; Rahbar, Elaheh; Baer, Lisa A

2016-01-01

hypothesized that pre-hospital plasma would improve hemostatic function as evaluated by rapid thrombelastography (rTEG). METHODS: We conducted a prospective observational study recruiting 257 trauma patients admitted to a Level I trauma center having received either blood products pre-hospital or in......BACKGROUND: The early use of blood products has been associated with improved patient outcomes following severe hemorrhage or traumatic injury. We aimed to investigate the influence of pre-hospital blood products (i.e. plasma and/or RBCs) on admission hemostatic properties and patient outcomes. We......-hospital within 6 hours of admission. Clinical data on patient demographics, blood biochemistry, injury severity score and mortality were collected. Admission rTEG was conducted to characterize the coagulation profile and hemostatic function. RESULTS: 75 patients received pre-hospital plasma and/or RBCs (PH group...

Demostration of 520 Gb/s/λ pre-equalized DFT-spread PDM-16QAM-OFDM signal transmission.

Science.gov (United States)

Li, Fan; Yu, Jianjun; Cao, Zizheng; Chen, Ming; Zhang, Junwen; Li, Xinying

2016-02-08

In this paper, we successfully transmit 8 × 520 Gb/s pre-equalized DFT-spread PDM-16QAM orthogonal frequency-division multiplexing (OFDM) signal over 840 km SMF with BER under 2.4 × 10(-2). We discuss how to obtain accurate tranceivers' response during pre-equalization for DFT-spread OFDM with coherent detection and we find conventional OFDM symbols training sequences (TSs) outperform DFT-spread OFDM symbols TSs in obtaining channel response for pre-equalization and equalization. Additionally, the optimal IFFT/FFT size is explored for the pre-equalized DFT-spread PDM-16QAM-OFDM transmission systems. It is the first time to realize 400 Gb/s/λ net rate OFDM signal transmission.

A 15-meter Multi-Gigabit W-band Bidirectional Wireless Bridge in Fiber-Optic Access Networks

DEFF Research Database (Denmark)

Pang, Xiaodan; Vegas Olmos, Juan José; Lebedev, Alexander

2013-01-01

. The down-converted signal is re-modulated on to the lightwave and transmit further through the fiber-optic system. In the uplink, both up-and down-conversion are performed by electrical means. Furthermore, we investigate both passive and active wireless transmitters in this work for both downlink......We present a bidirectional wireless bridge in the W-band enabling the seamless convergence between the wireless and fiber-optic access networks. In the downlink, a 16 Gbit/s QPSK signal is photonically up-converted at the wireless transmitter and electrically down-converted at the wireless receiver...... and uplink transmissions. With an active wireless transmitter, up to 15 meters wireless transmission is successfully achieved with a BER below the 7% FEC limit in the downlink....

On the Capacity of Hybrid Wireless Networks with Opportunistic Routing

Directory of Open Access Journals (Sweden)

Le Tan

2010-01-01

Full Text Available This paper studies the capacity of hybrid wireless networks with opportunistic routing (OR. We first extend the opportunistic routing algorithm to exploit high-speed data transmissions in infrastructure network through base stations. We then develop linear programming models to calculate the end-to-end throughput bounds from multiple source nodes to single as well as multiple destination nodes. The developed models are applied to study several hybrid wireless network examples. Through case studies, we investigate several factors that have significant impacts on the hybrid wireless network capacity under opportunistic routing, such as node transmission range, density and distribution pattern of base stations (BTs, and number of wireless channels on wireless nodes and base stations. Our numerical results demonstrate that opportunistic routing could achieve much higher throughput on both ad hoc and hybrid networks than traditional unicast routing (UR. Moreover, opportunistic routing can efficiently utilize base stations and achieve significantly higher throughput gains in hybrid wireless networks than in pure ad hoc networks especially with multiple-channel base stations.

A Technical Evaluation of Wireless Connectivity from Patient Monitors to an Anesthesia Information Management System During Intensive Care Unit Surgery.

Science.gov (United States)

Simpao, Allan F; Galvez, Jorge A; England, W Randall; Wartman, Elicia C; Scott, James H; Hamid, Michael M; Rehman, Mohamed A; Epstein, Richard H

2016-02-01

Surgical procedures performed at the bedside in the neonatal intensive care unit (NICU) at The Children's Hospital of Philadelphia were documented using paper anesthesia records in contrast to the operating rooms, where an anesthesia information management system (AIMS) was used for all cases. This was largely because of logistical problems related to connecting cables between the bedside monitors and our portable AIMS workstations. We implemented an AIMS for documentation in the NICU using wireless adapters to transmit data from bedside monitoring equipment to a portable AIMS workstation. Testing of the wireless AIMS during simulation in the presence of an electrosurgical generator showed no evidence of interference with data transmission. Thirty NICU surgical procedures were documented via the wireless AIMS. Two wireless cases exhibited brief periods of data loss; one case had an extended data gap because of adapter power failure. In comparison, in a control group of 30 surgical cases in which wired connections were used, there were no data gaps. The wireless AIMS provided a simple, unobtrusive, portable alternative to paper records for documenting anesthesia records during NICU bedside procedures.

Contributions to time-frequency synchronization in wireless systems

OpenAIRE

Koivisto, Tommi

2015-01-01

Time and frequency synchronization is an indispensable task for all wireless transceivers and systems. In modern wireless systems, such as 4G and future 5G systems, new wireless technologies set new challenges also to synchronization. In particular, new solutions for time and frequency synchronization are needed in multiantenna and cooperative systems. New research areas arise also in context of interference cancellation and cognitive radio systems where the transmission parameters of the sig...

Advanced Communication for Wireless Sensor Networks

Science.gov (United States)

2016-08-22

strategies that could be used to increase the single-hop transmission range of a wireless sensor network, increase energy efficiency (improve battery...substance placed within the reach of the network. Sensor measurements were quantized to save energy and bandwidth during transmission of the...the problem of assigning transmission powers to every node in order to maintain connectivity while minimizing the energy consumption of the whole

Theoretical investigation of dielectric corona pre-ionization TEA nitrogen laser based on transmission line method

Science.gov (United States)

Bahrampour, Alireza; Fallah, Robabeh; Ganjovi, Alireza A.; Bahrampour, Abolfazl

2007-07-01

This paper models the dielectric corona pre-ionization, capacitor transfer type of flat-plane transmission line traveling wave transverse excited atmospheric pressure nitrogen laser by a non-linear lumped RLC electric circuit. The flat-plane transmission line and the pre-ionizer dielectric are modeled by a lumped linear RLC and time-dependent non-linear RC circuit, respectively. The main discharge region is considered as a time-dependent non-linear RLC circuit where its resistance value is also depends on the radiated pre-ionization ultra violet (UV) intensity. The UV radiation is radiated by the resistance due to the surface plasma on the pre-ionizer dielectric. The theoretical predictions are in a very good agreement with the experimental observations. The electric circuit equations (including the ionization rate equations), the equations of laser levels population densities and propagation equation of laser intensities, are solved numerically. As a result, the effects of pre-ionizer dielectric parameters on the electrical behavior and output laser intensity are obtained.

Design of a Wireless Sensor Module for Monitoring Conductor Galloping of Transmission Lines.

Science.gov (United States)

Huang, Xinbo; Zhao, Long; Chen, Guimin

2016-10-09

Conductor galloping may cause flashovers and even tower collapses. The available conductor galloping monitoring methods often employ acceleration sensors to measure the conductor translations without considering the conductor twist. In this paper, a new sensor for monitoring conductor galloping of transmission lines based on an inertial measurement unit and wireless communication is proposed. An inertial measurement unit is used for collecting the accelerations and angular rates of a conductor, which are further transformed into the corresponding geographic coordinate frame using a quaternion transformation to reconstruct the galloping of the conductor. Both the hardware design and the software design are described in details. The corresponding test platforms are established, and the experiments show the feasibility and accuracy of the proposed monitoring sensor. The field operation of the proposed sensor in a conductor spanning 734 m also shows its effectiveness.

Design of an effective energy receiving adapter for microwave wireless power transmission application

Directory of Open Access Journals (Sweden)

Peng Xu

2016-10-01

Full Text Available In this paper, we demonstrate the viability of an energy receiving adapter in a 8×8 array form with high power reception efficiency with the resonator of artificial electromagnetic absorber being used as the element. Unlike the conventional reported rectifying antenna resonators, both the size of the element and the separations between the elements are electrically small in our design. The energy collecting process is explained with an equivalent circuit model, and a RF combining network is designed to combine the captured AC power from each element to one main terminal for AC-to-DC conversion. The energy receiving adapter yields a total reception efficiency of 67% (including the wave capture efficiency of 86% and the AC-to-DC conversion efficiency of 78%, which is quite promising for microwave wireless power transmission.

Optimal resonance configuration for ultrasonic wireless power transmission to millimeter-sized biomedical implants.

Science.gov (United States)

Miao Meng; Kiani, Mehdi

2016-08-01

In order to achieve efficient wireless power transmission (WPT) to biomedical implants with millimeter (mm) dimensions, ultrasonic WPT links have recently been proposed. Operating both transmitter (Tx) and receiver (Rx) ultrasonic transducers at their resonance frequency (fr) is key in improving power transmission efficiency (PTE). In this paper, different resonance configurations for Tx and Rx transducers, including series and parallel resonance, have been studied to help the designers of ultrasonic WPT links to choose the optimal resonance configuration for Tx and Rx that maximizes PTE. The geometries for disk-shaped transducers of four different sets of links, operating at series-series, series-parallel, parallel-series, and parallel-parallel resonance configurations in Tx and Rx, have been found through finite-element method (FEM) simulation tools for operation at fr of 1.4 MHz. Our simulation results suggest that operating the Tx transducer with parallel resonance increases PTE, while the resonance configuration of the mm-sized Rx transducer highly depends on the load resistance, Rl. For applications that involve large Rl in the order of tens of kΩ, a parallel resonance for a mm-sized Rx leads to higher PTE, while series resonance is preferred for Rl in the order of several kΩ and below.

Introductory survey for wireless infrared communications

Directory of Open Access Journals (Sweden)

Munsif Ali Jatoi

2014-08-01

Full Text Available Wireless infrared communications can be defined as the propagation of light waves in free space using infrared radiation whose range is 400–700 nm. This range corresponds to frequencies of hundreds of terahertz, which is high for higher data rate applications. Wireless infrared is applied for higher data rates applications such as wireless computing, wireless video and wireless multimedia communication applications. Introduced by Gfeller, this field has grown with different link configurations, improved transmitter efficiency, increased receiver responsivity and various multiple access techniques for improved quality. Errors are caused because of background light, which causes degradation overall system performance. Error correction techniques are used to remove the errors caused during transmission. This study provides a brief account on field theory used for error correction in wireless infrared systems. The results are produced in terms of bit error rate and signal-to-noise ratio for various bit lengths to show the ability of encoding and decoding algorithms.

Optical frequency upconversion technique for transmission of wireless MIMO-type signals over optical fiber.

Science.gov (United States)

Shaddad, R Q; Mohammad, A B; Al-Gailani, S A; Al-Hetar, A M

2014-01-01

The optical fiber is well adapted to pass multiple wireless signals having different carrier frequencies by using radio-over-fiber (ROF) technique. However, multiple wireless signals which have the same carrier frequency cannot propagate over a single optical fiber, such as wireless multi-input multi-output (MIMO) signals feeding multiple antennas in the fiber wireless (FiWi) system. A novel optical frequency upconversion (OFU) technique is proposed to solve this problem. In this paper, the novel OFU approach is used to transmit three wireless MIMO signals over a 20 km standard single mode fiber (SMF). The OFU technique exploits one optical source to produce multiple wavelengths by delivering it to a LiNbO3 external optical modulator. The wireless MIMO signals are then modulated by LiNbO3 optical intensity modulators separately using the generated optical carriers from the OFU process. These modulators use the optical single-sideband with carrier (OSSB+C) modulation scheme to optimize the system performance against the fiber dispersion effect. Each wireless MIMO signal is with a 2.4 GHz or 5 GHz carrier frequency, 1 Gb/s data rate, and 16-quadrature amplitude modulation (QAM). The crosstalk between the wireless MIMO signals is highly suppressed, since each wireless MIMO signal is carried on a specific optical wavelength.

Pre-hospital antibiotic treatment and mortality caused by invasive meningococcal disease, adjusting for indication bias

Directory of Open Access Journals (Sweden)

Matute-Cruz Petra

2009-04-01

Full Text Available Abstract Background Mortality from invasive meningococcal disease (IMD has remained stable over the last thirty years and it is unclear whether pre-hospital antibiotherapy actually produces a decrease in this mortality. Our aim was to examine whether pre-hospital oral antibiotherapy reduces mortality from IMD, adjusting for indication bias. Methods A retrospective analysis was made of clinical reports of all patients (n = 848 diagnosed with IMD from 1995 to 2000 in Andalusia and the Canary Islands, Spain, and of the relationship between the use of pre-hospital oral antibiotherapy and mortality. Indication bias was controlled for by the propensity score technique, and a multivariate analysis was performed to determine the probability of each patient receiving antibiotics, according to the symptoms identified before admission. Data on in-hospital death, use of antibiotics and demographic variables were collected. A logistic regression analysis was then carried out, using death as the dependent variable, and pre-hospital antibiotic use, age, time from onset of symptoms to parenteral antibiotics and the propensity score as independent variables. Results Data were recorded on 848 patients, 49 (5.72% of whom died. Of the total number of patients, 226 had received oral antibiotics before admission, mainly betalactams during the previous 48 hours. After adjusting the association between the use of antibiotics and death for age, time between onset of symptoms and in-hospital antibiotic treatment, pre-hospital oral antibiotherapy remained a significant protective factor (Odds Ratio for death 0.37, 95% confidence interval 0.15–0.93. Conclusion Pre-hospital oral antibiotherapy appears to reduce IMD mortality.

Trauma-informed care for children in the ambulance : international survey among pre-hospital providers

NARCIS (Netherlands)

Alisic, Eva; Tyler, Mark P; Giummarra, Melita J; Kassam-Adams, Rahim; Gouweloos, Juul; Landolt, Markus A; Kassam-Adams, Nancy

2017-01-01

Background: Pre-hospital providers, such as paramedics and emergency medical technicians, are in a position to provide key emotional support to injured children and their families. Objective: Our goal was to examine (a) pre-hospital providers' knowledge of traumatic stress in children, attitudes

Interactive Video Coding and Transmission over Heterogeneous Wired-to-Wireless IP Networks Using an Edge Proxy

Directory of Open Access Journals (Sweden)

Modestino James W

2004-01-01

Full Text Available Digital video delivered over wired-to-wireless networks is expected to suffer quality degradation from both packet loss and bit errors in the payload. In this paper, the quality degradation due to packet loss and bit errors in the payload are quantitatively evaluated and their effects are assessed. We propose the use of a concatenated forward error correction (FEC coding scheme employing Reed-Solomon (RS codes and rate-compatible punctured convolutional (RCPC codes to protect the video data from packet loss and bit errors, respectively. Furthermore, the performance of a joint source-channel coding (JSCC approach employing this concatenated FEC coding scheme for video transmission is studied. Finally, we describe an improved end-to-end architecture using an edge proxy in a mobile support station to implement differential error protection for the corresponding channel impairments expected on the two networks. Results indicate that with an appropriate JSCC approach and the use of an edge proxy, FEC-based error-control techniques together with passive error-recovery techniques can significantly improve the effective video throughput and lead to acceptable video delivery quality over time-varying heterogeneous wired-to-wireless IP networks.

The epidemiology of Scottish trauma: A comparison of pre-hospital and in-hospital deaths, 2000 to 2011.

Science.gov (United States)

Morrison, Jonathan J; Yapp, Liam Z; Beattie, Anne; Devlin, Eimar; Samarage, Milan; McCaffer, Craig; Jansen, Jan O

2016-02-01

To characterise the temporal trends and urban-rural distribution of fatal injuries in Scotland through the analysis of mortality data collected by the National Records of Scotland. The prospectively collected NRS database was queried using ICD-10 codes for all Scottish trauma deaths during the period 2000 to 2011. Patients were divided into pre-hospital and in-hospital groups depending on the location of death. Incidence was plotted against time and linear regression was used to identify temporal trends. A total of 13,100 deaths were analysed. There were 4755 (36.3%) patients in the pre-hospital group with a median age (IQR) of 42 (28-58) years. The predominant cause of pre-hospital death related to vehicular injury (27.8%), which had a decreasing trend over the study period (p = 0.004). In-hospital, patients had a median age of 80 (58-88) years and the majority (67.0%) of deaths occurred following a fall on the level. This trend was shown to increase over the decade of study (p = 0.020). In addition, the incidence of urban incidents remained static, but the rate of rural fatal trauma decreased (p Scottish trauma patients die prior to hospital admission and the predominant mechanism of injury is due to road traffic accidents. This contrasts with in-hospital deaths, which are mainly observed in elderly patients following a fall from standing height. Further research is required to determine the preventability of fatal traumatic injury in Scotland. Copyright © 2015 Royal College of Surgeons of Edinburgh (Scottish charity number SC005317) and Royal College of Surgeons in Ireland. Published by Elsevier Ltd. All rights reserved.

The wireless sensor network monitoring system for regional environmental nuclear radiation

International Nuclear Information System (INIS)

Liu Chong; Liu Dao; Wang Yaojun; Xie Yuxi; Song Lingling

2012-01-01

The wireless sensor network (WSN) technology has been utilized to design a new regional environmental radiation monitoring system based on the wireless sensor networks to meet the special requirements of monitoring the nuclear radiation in certain regions, and realize the wireless transmission of measurement data, information processing and integrated measurement of the nuclear radiation and the corresponding environmental parameters in real time. The system can be applied to the wireless monitoring of nuclear radiation dose in the nuclear radiation environment. The measured data and the distribution of radiation dose can be vividly displayed on the graphical interface in the host computer. The system has functioned with the wireless transmission and control, the data storage, the historical data inquiry, the node remote control. The experimental results show that the system has the advantages of low power consumption, stable performance, network flexibility, range of measurement and so on. (authors)

The time light signals of New Zealand: yet another way of communicating time in the pre-wireless era

Science.gov (United States)

Kinns, Roger

2017-08-01

The signalling of exact time using an array of lights appears to have been unique to New Zealand. It was a simple and effective solution for calibration of marine chronometers when transmission of time signals by wireless was in its infancy. Three lights, coloured green, red and white, were arranged in a vertical array. They were switched on in a defined sequence during the evening and then extinguished together to signal exact time. Time lights were first operated at the Dominion Observatory in Wellington during February 1912 and on the Ferry Building in Auckland during October 1915. The Wellington lights were immediately adjacent to the observatory buildings, but those in Auckland were operated using telegraph signals from Wellington. The timings varied over the years, but the same physical arrangement was retained at each location. The time light service was withdrawn during 1937, when wireless signals had become almost universally available for civil and navigation purposes.

Challenges and Ideas to Achieve Wireless 100 Gb/s Transmission: An Overview of Challenges and Solutions within the German Research Foundation (DFG) Special Priority Program SPP1655

Science.gov (United States)

Kraemer, Rolf

2017-09-01

Wireless communications is one of the fastest growing technology fields, driving numerous other innovations in electronics. One challenging research area within the wireless field is to achieve much higher transmission rates. First products with up to 3 Gb/s are in the market. In the coming years we predict this speed growing quickly up to and beyond 100 Gb/s. Today it is an open question how we can realize a wireless system at this speed. If we intend to use such systems in a mobile environment, we can only afford to spend approximately 1-10 pW/b for the end-to-end communication. This includes RF-transmission and all processing and protocol steps. The SPP1655 of the DFG was set up to investigate new paradigms for achieving the 100 Gb/s wireless transmission goal. Within 11 coordinated projects researchers from all over Germany are addressing several relevant issues ranging from the antennas and RF-Frontend, baseband-processing and error correction to protocol processing. A number of limitations of current approaches have to be investigated and new algorithms must be found in order to achieve the intended goal. One of the big challenges is finding the correct balance between analog and digital signal processing to achieve an extremely high performance at very low energy consumption. Another challenge is to find a good balance between bandwidth and bandwidth efficiency to achieve the 100 Gbps goal. Finally, protocol processing will need new approaches to decouple the central processor of a computer from the high-end input/output operations. Within this editorial we will address the main challenges and briefly outline the approaches of the running projects. The rest of this special issue will be devoted to more detailed descriptions and achievements of the individual projects of SPP1655.

Extreme-Environment Silicon-Carbide (SiC) Wireless Sensor Suite

Science.gov (United States)

Yang, Jie

2015-01-01

Phase II objectives: Develop an integrated silicon-carbide wireless sensor suite capable of in situ measurements of critical characteristics of NTP engine; Compose silicon-carbide wireless sensor suite of: Extreme-environment sensors center, Dedicated high-temperature (450 deg C) silicon-carbide electronics that provide power and signal conditioning capabilities as well as radio frequency modulation and wireless data transmission capabilities center, An onboard energy harvesting system as a power source.

[Burnout syndrome in pre-hospital and hospital emergency. Cognitive study in two cohorts of nurses].

Science.gov (United States)

Cicchitti, Chiara; Cannizzaro, Giorgia; Rosi, Fabrizio; Maccaroni, Roberto; Menditto, Vincenzo G

2014-01-01

Burnout syndrome (BOS) associated with stress has been documented in health care professionals in many specialties. The emergency department and the pre-hospital healthcare services are highly stressful environments. Little is known about the BOS in critical care nursing staff. The objective of the study is to compare the incidence of BOS and its three domains, namely, emotional exhaustion, depersonalization and reduced professional accomplishment, in two cohorts of critical care nurses: a pre-hospital and a hospital emergency service. A survey using a questionnaire (the Maslach Burnout Inventory-General Survey, MBI-GS), among nurses of two Italian emergency services has been performed: a hospital emergency service (HES, Emergency Department or "Pronto Soccorso") and a pre-hospital emergency service (PHES, territorial healthcare service or "Centrale Operativa 118"). All 60 nurses surveyed (82% female) filled the questionnaires. BOS-related symptoms have been identified in at least 50% of the nurses in the HES: 50% suffered a medium-high emotional exhaustion, 75% had a medium-high depersonalization and 92.5% had a medium-high reduced professional accomplishment. Among the PEHS nurses, BOS-related symptoms have been identified in at least 60% of the respondents: 60% had a medium-high emotional exhaustion, 70% had a medium-high depersonalization and 95% had a medium-high reduced professional accomplishment. Moreover, the likelihood that a nurse has a severe BOS, that is at least one degree of high burnout or ≥2 degrees of medium burnout, is significantly higher in the group of the PHES than in the HES (90% vs 60%, p nursing staff had a severe BOS. The incidence of BOS appeared to be similar among PHES and HES nurses with a higher trend for the former. Further interventional studies are needed to investigate the determinants of BOS among critical care nurses and the potentially preventive strategies.

Space Solar Power Technology Demonstration for Lunar Polar Applications: Laser-Photovoltaic Wireless Power Transmission

Science.gov (United States)

Henley, M. W.; Fikes, J. C.; Howell, J.; Mankins, J. C.; Howell, Joe T. (Technical Monitor)

2002-01-01

Space Solar Power technology offers unique benefits for near-term NASA space science missions, which can mature this technology for other future applications. "Laser-Photo-Voltaic Wireless Power Transmission" (Laser-PV WPT) is a technology that uses a laser to beam power to a photovoltaic receiver, which converts the laser's light into electricity. Future Laser-PV WPT systems may beam power from Earth to satellites or large Space Solar Power satellites may beam power to Earth, perhaps supplementing terrestrial solar photo-voltaic receivers. In a near-term scientific mission to the moon, Laser-PV WPT can enable robotic operations in permanently shadowed lunar polar craters, which may contain ice. Ground-based technology demonstrations are proceeding, to mature the technology for this initial application, in the moon's polar regions.

An overview of the construction of emergency and pre-hospital first aid platform

Directory of Open Access Journals (Sweden)

Song Chen

2018-01-01

Full Text Available To further improve the ability of pre-hospital and in-hospital collaborative treatment, strengthen emergency multidisciplinary cooperation and construct a scientific, rational and efficient emergency system, under the support of former chairman Yu Xue-zhong, Dr. Li Chun-sheng and numerous colleagues in the industry, the Emergency Medicine Society of the Chinese Medical Association appeal to us to draft Construction of Emergency and Pre-hospital Platform. Based on this background, the platform of emergency and pre-hospital first aid helps to build a “one horizontal and one Longitudinal” treatment model, using the horizontal and longitudinal patterns to integrate emergency medical resources to satisfy the automatic information integration and intelligent analysis sharing, realizing the emergency management visualization and medical information digitization, simplifying the medical process and establishing a perfect standard for the emergent diseases, thereby ultimately achieving efficient diagnosis and scientific treatment.

On the Security of Data Collection and Transmission from Wireless Sensor Networks in the Context of Internet of Things

OpenAIRE

Yu, Hong; He, Jingsha; Liu, Ruohong; Ji, Dajie

2013-01-01

In the context of Internet of Things (IoT), multiple cooperative nodes in wireless sensor networks (WSNs) can be used to monitor an event, jointly generate a report and then send it to one or more Internet nodes for further processing. A primary security requirement in such applications is that every event data report be authenticated to intended Internet users and effectively filtered on its way to the Internet users to realize the security of data collection and transmission from the WSN. H...

Study on electromagnetic characteristics of the magnetic coupling resonant coil for the wireless power transmission system.

Science.gov (United States)

Wang, Zhongxian; Liu, Yiping; Wei, Yonggeng; Song, Yilin

2018-01-01

The resonant coil design is taken as the core technology in the magnetic coupling resonant wireless power transmission system, which achieves energy transmission by the coupling of the resonant coil. This paper studies the effect of the resonant coil on energy transmission and the efficiency of the system. Combining a two-coil with a three-coil system, the optimum design method for the resonant coil is given to propose a novel coil structure. First, the co-simulation methods of Pspice and Maxwell are used. When the coupling coefficient of the resonant coil is different, the relationship between system transmission efficiency, output power, and frequency is analyzed. When the self-inductance of the resonant coil is different, the relationship between the performance and frequency of the system transmission is analyzed. Then, two-coil and three-coil structure models are built, and the parameters of the magnetic field of the coils are calculated and analyzed using the finite element method. In the end, a dual E-type simulation circuit model is used to optimize the design of the novel resonance coil. The co-simulation results show that the coupling coefficients of the two-coil, three-coil, and novel coil systems are 0.017, 0.17 and 0.0126, respectively. The power loss of the novel coil is 16.4 mW. There is an obvious improvement in the three-coil system, which shows that the magnetic leakage of the field and the energy coupling are relatively small. The new structure coil has better performance, and the load loss is lower; it can improve the system output power and transmission efficiency.

X-raying neighbour discovery in a wireless sensor network ...

African Journals Online (AJOL)

In most wireless sensor networks, the nodes are often assumed to be stationary. However, network connectivity is subject to changes arising from interference in wireless communication, changes in transmission power or loss of synchronization among neighbouring network nodes. Hence, even after a sensor node is aware ...

The Optimization Based Dynamic and Cyclic Working Strategies for Rechargeable Wireless Sensor Networks with Multiple Base Stations and Wireless Energy Transfer Devices

Science.gov (United States)

Ding, Xu; Han, Jianghong; Shi, Lei

2015-01-01

In this paper, the optimal working schemes for wireless sensor networks with multiple base stations and wireless energy transfer devices are proposed. The wireless energy transfer devices also work as data gatherers while charging sensor nodes. The wireless sensor network is firstly divided into sub networks according to the concept of Voronoi diagram. Then, the entire energy replenishing procedure is split into the pre-normal and normal energy replenishing stages. With the objective of maximizing the sojourn time ratio of the wireless energy transfer device, a continuous time optimization problem for the normal energy replenishing cycle is formed according to constraints with which sensor nodes and wireless energy transfer devices should comply. Later on, the continuous time optimization problem is reshaped into a discrete multi-phased optimization problem, which yields the identical optimality. After linearizing it, we obtain a linear programming problem that can be solved efficiently. The working strategies of both sensor nodes and wireless energy transfer devices in the pre-normal replenishing stage are also discussed in this paper. The intensive simulations exhibit the dynamic and cyclic working schemes for the entire energy replenishing procedure. Additionally, a way of eliminating “bottleneck” sensor nodes is also developed in this paper. PMID:25785305

The optimization based dynamic and cyclic working strategies for rechargeable wireless sensor networks with multiple base stations and wireless energy transfer devices.

Science.gov (United States)

Ding, Xu; Han, Jianghong; Shi, Lei

2015-03-16

In this paper, the optimal working schemes for wireless sensor networks with multiple base stations and wireless energy transfer devices are proposed. The wireless energy transfer devices also work as data gatherers while charging sensor nodes. The wireless sensor network is firstly divided into sub networks according to the concept of Voronoi diagram. Then, the entire energy replenishing procedure is split into the pre-normal and normal energy replenishing stages. With the objective of maximizing the sojourn time ratio of the wireless energy transfer device, a continuous time optimization problem for the normal energy replenishing cycle is formed according to constraints with which sensor nodes and wireless energy transfer devices should comply. Later on, the continuous time optimization problem is reshaped into a discrete multi-phased optimization problem, which yields the identical optimality. After linearizing it, we obtain a linear programming problem that can be solved efficiently. The working strategies of both sensor nodes and wireless energy transfer devices in the pre-normal replenishing stage are also discussed in this paper. The intensive simulations exhibit the dynamic and cyclic working schemes for the entire energy replenishing procedure. Additionally, a way of eliminating "bottleneck" sensor nodes is also developed in this paper.

Privacy-preserving telecardiology sensor networks: toward a low-cost portable wireless hardware/software codesign.

Science.gov (United States)

Hu, Fei; Jiang, Meng; Wagner, Mark; Dong, De-Cun

2007-11-01

Recently, a remote-sensing platform based on wireless interconnection of tiny ECG sensors called Telecardiology Sensor Networks (TSN) provided a promising approach to perform low-cost real-time cardiac patient monitoring at any time in community areas (such as elder nursing homes or hospitals). The contribution of this research is the design of a practical TSN hardware/software platform for a typical U.S. healthcare community scenario (such as large nursing homes with many elder patients) to perform real-time healthcare data collections. On the other hand, due to the radio broadcasting nature of MANET, a TSN has the risk of losing the privacy of patients' data. Medical privacy has been highly emphasized by U.S. Department of Health and Human Services. This research also designs a medical security scheme with low communication overhead to achieve confidential electrocardiogram data transmission in wireless medium.

Increased Efficiency of Face Recognition System using Wireless Sensor Network

Directory of Open Access Journals (Sweden)

Rajani Muraleedharan

2006-02-01

Full Text Available This research was inspired by the need of a flexible and cost effective biometric security system. The flexibility of the wireless sensor network makes it a natural choice for data transmission. Swarm intelligence (SI is used to optimize routing in distributed time varying network. In this paper, SI maintains the required bit error rate (BER for varied channel conditions while consuming minimal energy. A specific biometric, the face recognition system, is discussed as an example. Simulation shows that the wireless sensor network is efficient in energy consumption while keeping the transmission accuracy, and the wireless face recognition system is competitive to the traditional wired face recognition system in classification accuracy.

Simplified Fiber-Wireless Distribution of HD Video in Passive and Active W-band Close Proximity Terminals

DEFF Research Database (Denmark)

Lebedev, Alexander; Rodes Lopez, Roberto; Yu, Xianbin

2012-01-01

We experimentally demonstrate uncompressed high-definition (HD) video distribution at 84 GHz Radio over Fiber link achieving up to 3 meters of wireless transmission. We experimentally emulate Metro-Access architecture by deploying single/multimode fibers. Passive and active approaches for remote...... antenna unit (RAU) are experimentally investigated. The bit error rate (BER) performance of the optical and wireless channels is reported. A successful transmission of uncompressed HD video in the W-band wireless channel is demonstrated with prospects to pave the way for application-focused fiber-wireless...

Quality assurance of pre-operative assessment--a review of quality assurance activities related to pre-operative assessment in nine hospitals in The Netherlands

NARCIS (Netherlands)

Klazinga, N. S.; Helsloot, R.

1989-01-01

Pre-operative assessment of patients for surgery is one of the most prevalent topics for quality assurance by peer-review in Dutch hospitals. This article describes the experiences with pre-operative assessment in nine hospitals. It is discussed why preoperative assessment is performed, what tests

Key Management for Secure Multicast over IPv6 Wireless Networks

Directory of Open Access Journals (Sweden)

Siddiqi Mohammad Umar

2006-01-01

Full Text Available Multicasting is an efficient method for transmission and routing of packets to multiple destinations using fewer network resources. Along with widespread deployment of wireless networks, secure multicast over wireless networks is an important and challenging goal. In this paper, we extend the scope of a recent new key distribution scheme to a security framework that offers a novel solution for secure multicast over IPv6 wireless networks. Our key management framework includes two scenarios for securely distributing the group key and rekey messages for joining and leaving a mobile host in secure multicast group. In addition, we perform the security analysis and provide performance comparisons between our approach and two recently published scenarios. The benefits of our proposed techniques are that they minimize the number of transmissions required to rekey the multicast group and impose minimal storage requirements on the multicast group. In addition, our proposed schemes are also very desirable from the viewpoint of transmission bandwidth savings since an efficient rekeying mechanism is provided for membership changes and they significantly reduce the required bandwidth due to key updating in mobile networks. Moreover, they achieve the security and scalability requirements in wireless networks.

160 Gbit/s photonics wireless transmission in the 300-500 GHz band

DEFF Research Database (Denmark)

Yu, Xianbin; Jia, S.; Hu, Hao

2016-01-01

To accommodate the ever increasing wireless traffic in the access networks, considerable efforts have been recently invested in developing photonics-assisted wireless communication systems with very high data rates. Superior to photonic millimeter-wave systems, terahertz (THz) band (300 GHz-10 THz...

The top five research priorities in physician-provided pre-hospital critical care: a consensus report from a European research collaboration

Directory of Open Access Journals (Sweden)

Lockey David

2011-10-01

Full Text Available Abstract Background Physician-manned emergency medical teams supplement other emergency medical services in some countries. These teams are often selectively deployed to patients who are considered likely to require critical care treatment in the pre-hospital phase. The evidence base for guidelines for pre-hospital triage and immediate medical care is often poor. We used a recognised consensus methodology to define key priority areas for research within the subfield of physician-provided pre-hospital critical care. Methods A European expert panel participated in a consensus process based upon a four-stage modified nominal group technique that included a consensus meeting. Results The expert panel concluded that the five most important areas for further research in the field of physician-based pre-hospital critical care were the following: Appropriate staffing and training in pre-hospital critical care and the effect on outcomes, advanced airway management in pre-hospital care, definition of time windows for key critical interventions which are indicated in the pre-hospital phase of care, the role of pre-hospital ultrasound and dispatch criteria for pre-hospital critical care services. Conclusion A modified nominal group technique was successfully used by a European expert group to reach consensus on the most important research priorities in physician-provided pre-hospital critical care.

A systematic review of transmission dynamic studies of methicillin-resistant Staphylococcus aureus in non-hospital residential facilities.

Science.gov (United States)

Kwok, Kin On; Read, Jonathan M; Tang, Arthur; Chen, Hong; Riley, Steven; Kam, Kai Man

2018-04-18

Non-hospital residential facilities are important reservoirs for MRSA transmission. However, conclusions and public health implications drawn from the many mathematical models depicting nosocomial MRSA transmission may not be applicable to these settings. Therefore, we reviewed the MRSA transmission dynamics studies in defined non-hospital residential facilities to: (1) provide an overview of basic epidemiology which has been addressed; (2) identify future research direction; and (3) improve future model implementation. A review was conducted by searching related keywords in PUBMED without time restriction as well as internet searches via Google search engine. We included only articles describing the epidemiological transmission pathways of MRSA/community-associated MRSA within and between defined non-hospital residential settings. Among the 10 included articles, nursing homes (NHs) and correctional facilities (CFs) were two settings considered most frequently. Importation of colonized residents was a plausible reason for MRSA outbreaks in NHs, where MRSA was endemic without strict infection control interventions. The importance of NHs over hospitals in increasing nosocomial MRSA prevalence was highlighted. Suggested interventions in NHs included: appropriate staffing level, screening and decolonizing, and hand hygiene. On the other hand, the small population amongst inmates in CFs has no effect on MRSA community transmission. Included models ranged from system-level compartmental models to agent-based models. There was no consensus over the course of disease progression in these models, which were mainly featured with NH residents /CF inmates/ hospital patients as transmission pathways. Some parameters used by these models were outdated or unfit. Importance of NHs has been highlighted from these current studies addressing scattered aspects of MRSA epidemiology. However, the wide variety of non-hospital residential settings suggest that more work is needed before

How far are transmission measurements of pre-equilibrium stopping influenced by impact parameter selection?

International Nuclear Information System (INIS)

Semrad, D.; Bergsmann, M.; Bauer, P.; Diez-Muino, R.; Arnau, S.A.

2000-01-01

A slow ion that impinges on a target will need to travel a certain distance within the target - called pre-equilibrium length - in order to reach charge equilibrium. In this transient region, projectiles may suffer energy loss different from the mean value. For gas targets, most of the relevant cross-sections and energy transfers can be determined separately by experiment. This allows one to relate these data to the stopping cross-section and to simulate the passage of ions through gas by Monte-Carlo techniques. For solid targets matter is worse, but a universal formalism how pre-equilibrium processes may be determined from transmission data is well documented by Sigmund [14-15]. In transmission experiments usually only these projectiles are analyzed that have missed the central region of the target atoms. It is, however, a matter of fact that projectiles passing closer to the nucleus are more likely to lose energy. In the case of thin targets these projectiles are deflected out of the detector acceptance leading to a reduction of the measured average energy loss. Hence, stopping data may be influenced by so-called impact parameter selection (IPS) according to the layout of the experiment. This IPS clearly acts also in the regime of pre-equilibrium stopping. Using Monte-Carlo simulation we studied to which extent in a typical transmission experiment energy loss is influenced by pre-equilibrium stopping and by IPS, respectively. For feasibility, instead of a solid target, we follow the trajectories through a dense gas target. We find that in an actual experiment with small detector opening angle the formalism to describe pre-equilibrium stopping has to include IPS

Pre-eclampsia: Factores de riesgo. Estudio en el Hospital Nacional Cayetano Heredia.

Directory of Open Access Journals (Sweden)

Manuel Salviz Salhuana

1996-01-01

Full Text Available Objetivo: El objetivo fue evaluar los factores de riesgo asociados a pre-eclampsia en nuestro hospital. Material y métodos: Se realizó un estudio prospectivo, de tipo caso-control concurrente en 88 pacientes con pre-eclampsia e igual número de controles. El trabajo se llevó a cabo en el Servicio de Obstetricia del Hospital Nacional Cayetano Heredia entre los meses de marzo a agosto de 1993. Resultados: Los factores asociados a pre-eclampsia fueron el antecedente previo a pre-eclampsia (OR:17, el índice de masa corporal elevado (OR:9.6, la raza predominantemente blanca (OR:6.4, el antecedente familiar de hipertensión arterial (OR: 5.2, la falta de control pre-natal y la nuliparidad (OR: 2.5. La incidencia de pre-eclampsia fue 4.11%, y requirieron parto por cesárea el 69.3% de las pacientes. Presentaron complicaciones en el puerperio inmediato 28.4% de los casos, siendo más frecuentes las infecciones. (Rev Med Hered 1996; 7: 24-31.

Development and Operation of Dual-Mode Analyzers for Wireless Power Consortium/Power Matters Alliance Wireless Power Systems.

Science.gov (United States)

Um, Keehong

2016-05-01

We have designed a protocol analyzer to be used in wireless power systems and analyzed the operation of wireless chargers defined by standards of Qi of Wireless Power Consortium (WPC) and Power Matters Alliance (PMA) protocols. The integrated circuit (IC, or microchip) developed so far for wireless power transmission is not easily adopted by chargers for specific purposes. A device for measuring the performance of test equipment currently available is required to transform and expand the types of protocol. Since a protocol analyzer with these functions is required, we have developed a device that can analyze the two protocols of WPC and PMA at the same time. As a result of our research, we present a dual-mode system that can analyze the protocols of both WPC and PMA.

Progress and monitoring system on compression and transmission technologies of dynamic image

International Nuclear Information System (INIS)

Kobayashi, Hiroyuki; Saijo, Nobuyuki; Nakajo, Ken

2001-01-01

The Toshiba Corporation developed a real-time dynamic image transmission matched with quality of transmission circuit by using MPEG-4 which was recent international standard system for the dynamic image coding system. Concretely, this system made possible on real-time dynamic image transmission even at transmission on wireless circuit such as portable telephone, PHS, wireless LAN, and so on, at viewpoint of the mobile communication. And, by using the wireless circuit, it could be built without any limit of transmission cable, to realize its layout-free establishment. In addition, this system uses only image for communication without using voice, and some devices were carried out to upgrade image and frame speed as possible. Here were described on outlines of transmission system and principle of detection MPEG-4, and function and application of monitoring system using this system. (G.K.)

Distributed wireless quantum communication networks

International Nuclear Information System (INIS)

Yu Xu-Tao; Xu Jin; Zhang Zai-Chen

2013-01-01

The distributed wireless quantum communication network (DWQCN) has a distributed network topology and transmits information by quantum states. In this paper, we present the concept of the DWQCN and propose a system scheme to transfer quantum states in the DWQCN. The system scheme for transmitting information between any two nodes in the DWQCN includes a routing protocol and a scheme for transferring quantum states. The routing protocol is on-demand and the routing metric is selected based on the number of entangled particle pairs. After setting up a route, quantum teleportation and entanglement swapping are used for transferring quantum states. Entanglement swapping is achieved along with the process of routing set up and the acknowledgment packet transmission. The measurement results of each entanglement swapping are piggybacked with route reply packets or acknowledgment packets. After entanglement swapping, a direct quantum link between source and destination is set up and quantum states are transferred by quantum teleportation. Adopting this scheme, the measurement results of entanglement swapping do not need to be transmitted specially, which decreases the wireless transmission cost and transmission delay. (general)

Time and Energy Efficient Relay Transmission for Multi-Hop Wireless Sensor Networks.

Science.gov (United States)

Kim, Jin-Woo; Barrado, José Ramón Ramos; Jeon, Dong-Keun

2016-06-27

The IEEE 802.15.4 standard is widely recognized as one of the most successful enabling technologies for short range low rate wireless communications and it is used in IoT applications. It covers all the details related to the MAC and PHY layers of the IoT protocol stack. Due to the nature of IoT, the wireless sensor networks are autonomously self-organized networks without infrastructure support. One of the issues in IoT is the network scalability. To address this issue, it is necessary to support the multi-hop topology. The IEEE 802.15.4 network can support a star, peer-to-peer, or cluster-tree topology. One of the IEEE 802.15.4 topologies suited for the high predictability of performance guarantees and energy efficient behavior is a cluster-tree topology where sensor nodes can switch off their transceivers and go into a sleep state to save energy. However, the IEEE 802.15.4 cluster-tree topology may not be able to provide sufficient bandwidth for the increased traffic load and the additional information may not be delivered successfully. The common drawback of the existing approaches is that they do not address the poor bandwidth utilization problem in IEEE 802.15.4 cluster-tree networks, so it is difficult to increase the network performance. Therefore, to solve this problem in this paper we study a relay transmission protocol based on the standard protocol in the IEEE 802.15.4 MAC. In the proposed scheme, the coordinators can relay data frames to their parent devices or their children devices without contention and can provide bandwidth for the increased traffic load or the number of devices. We also evaluate the performance of the proposed scheme through simulation. The simulation results demonstrate that the proposed scheme can improve the reliability, the end-to-end delay, and the energy consumption.

Thermoelectric Powered Wireless Sensors for Dry-Cask Storage

Science.gov (United States)

Carstens, Thomas Alan

This study focuses on the development of self-powered wireless sensors. These sensors can be used to measure key parameters in extreme environments; e.g., temperature monitoring for spent nuclear fuel during dry-cask storage. This study has developed a design methodology for these self-powered monitoring systems. The main elements that constitute this work consist of selecting and testing a power source for the wireless sensor, determination of the attenuation of the wireless signal, and testing the wireless sensor circuitry in an extreme environment. OrigenArp determined the decay heat and gamma/neutron source strength of the spent fuel throughout the service life of the dry-cask. A first principles analysis modeled the temperatures inside the dry-cask. A finite-element heat transfer code calculated the temperature distribution of the thermoelectric and heat sink. The temperature distributions determine the power produced by the thermoelectric. It was experimentally verified that a thermoelectric generator (HZ-14) with a DC/DC converter (Linear Technology LTC3108EDE) can power a transceiver (EmbedRF) at condition which represent prototypical conditions throughout and beyond the service life of the dry-cask. The wireless sensor is required to broadcast with enough power to overcome the attenuation from the dry-cask. It will be important to minimize the attenuation of the signal in order to broadcast with a small transmission power. To investigate the signal transmission through the dry-cask, CST Microwave Studio was used to determine the scattering parameter S2,1 for a horizontal dry-cask. Important parameters that can influence the transmission of the signal are antenna orientation, antenna placement, and transmission frequency. The thermoelectric generator, DC/DC converter, and transceiver were exposed to 60Co gamma radiation (exposure rate170.3 Rad/min) at the University of Wisconsin Medical Radiation Research Center. The effects of gamma radiation on the

mm-Wave Wireless Communications based on Silicon Photonics Integrated Circuits

DEFF Research Database (Denmark)

Rommel, Simon; Heck, Martijn; Vegas Olmos, Juan José

Hybrid photonic-wireless transmission schemes in the mm-wave frequency range are promising candidates to enable the multi-gigabit per second data communications required from wireless and mobile networks of the 5th and future generations. Photonic integration may pave the way to practical applica...

Patient monitoring using infrastructure-oriented wireless LANs.

Science.gov (United States)

Varshney, Upkar

2006-01-01

There is considerable interest in using wireless and mobile technologies in patient monitoring in diverse environments including hospitals and nursing homes. However, there has not been much work in determining the requirements of patient monitoring and satisfying these requirements using infrastructure-oriented wireless networks. In this paper, we derive several requirements of patient monitoring and show how infrastructure-oriented wireless LANs, such as versions of IEEE 802.11, can be used to support patient monitoring in diverse environments.

Pre-hospitalization, hospitalization, and post-hospitalization costs of patients with neurocysticercosis treated at the Instituto Nacional de Neurologia y Neurocirugia (INNN in Mexico City, Mexico

Directory of Open Access Journals (Sweden)

Rachana Bhattarai

2018-05-01

Full Text Available ABSTRACT The objective of this study was to estimate the direct costs associated with the diagnosis and treatment of neurocysticercosis (NCC during pre-hospitalization, hospitalization, and post-hospitalization periods for 108 NCC patients treated at the Instituto Nacional de Neurologia y Neurocirugia (INNN in Mexico City, Mexico. Information on clinical manifestations, diagnostic tests, hospitalizations, surgical procedures, prescription medication, and other treatments was collected via medical chart reviews. Uncertain values for costs and frequency of treatments were imputed using bootstrap techniques. The average per-patient pre-hospitalization and hospitalization costs were US$ 257 (95% CI: 185 – 329 and US$ 2,576 (95% CI: 2,244 – 2,908, respectively. Post-hospitalization costs tended to decrease over time, with estimates for the first five years post-hospitalization of US$ 475 (95% CI: 423 – 527, US$ 228 (95% CI: 167 – 288, US$ 157 (95% CI: 111 – 202, US$ 150 (95% CI: 106 – 204, and US$ 91 (95% CI: 27 – 154, respectively. NCC results in a significant economic burden for patients requiring hospitalization, with this burden continuing years post-hospitalization.

Pre-hospital transport times and survival for Hypotensive patients with penetrating thoracic trauma

Directory of Open Access Journals (Sweden)

Mamta Swaroop

2013-01-01

Full Text Available Background: Achieving definitive care within the "Golden Hour" by minimizing response times is a consistent goal of regional trauma systems . This study hypothesizes that in urban Level I Trauma Centers, shorter pre-hospital times would predict outcomes in penetrating thoracic injuries. Materials and Methods: A retrospective cohort study was performed using a statewide trauma registry for the years 1999-2003 . Total pre-hospital times were measured for urban victims of penetrating thoracic trauma. Crude and adjusted mortality rates were compared by pre-hospital time using STATA statistical software. Results: During the study period, 908 patients presented to the hospital after penetrating thoracic trauma, with 79% surviving . Patients with higher injury severity scores (ISS were transported more quickly. Injury severity scores (ISS ≥16 and emergency department (ED hypotension (systolic blood pressure, SBP <90 strongly predicted mortality (P < 0.05 for each . In a logistic regression model including age, race, and ISS, longer transport times for hypotensive patients were associated with higher mortality rates (all P values <0.05. This was seen most significantly when comparing patient transport times 0-15 min and 46-60 min (P < 0.001. Conclusion: In victims of penetrating thoracic trauma, more severely injured patients arrive at urban trauma centers sooner . Mortality is strongly predicted by injury severity, although shorter pre-hospital times are associated with improved survival . These results suggest that careful planning to optimize transport time-encompassing hospital capacity and existing resources, traffic patterns, and trauma incident densities may be beneficial in areas with a high burden of penetrating trauma.

Capacity of Heterogeneous Mobile Wireless Networks with D-Delay Transmission Strategy.

Science.gov (United States)

Wu, Feng; Zhu, Jiang; Xi, Zhipeng; Gao, Kai

2016-03-25

This paper investigates the capacity problem of heterogeneous wireless networks in mobility scenarios. A heterogeneous network model which consists of n normal nodes and m helping nodes is proposed. Moreover, we propose a D-delay transmission strategy to ensure that every packet can be delivered to its destination nodes with limited delay. Different from most existing network schemes, our network model has a novel two-tier architecture. The existence of helping nodes greatly improves the network capacity. Four types of mobile networks are studied in this paper: i.i.d. fast mobility model and slow mobility model in two-dimensional space, i.i.d. fast mobility model and slow mobility model in three-dimensional space. Using the virtual channel model, we present an intuitive analysis of the capacity of two-dimensional mobile networks and three-dimensional mobile networks, respectively. Given a delay constraint D, we derive the asymptotic expressions for the capacity of the four types of mobile networks. Furthermore, the impact of D and m to the capacity of the whole network is analyzed. Our findings provide great guidance for the future design of the next generation of networks.

Performance Analysis of Cluster Formation in Wireless Sensor Networks.

Science.gov (United States)

Montiel, Edgar Romo; Rivero-Angeles, Mario E; Rubino, Gerardo; Molina-Lozano, Heron; Menchaca-Mendez, Rolando; Menchaca-Mendez, Ricardo

2017-12-13

Clustered-based wireless sensor networks have been extensively used in the literature in order to achieve considerable energy consumption reductions. However, two aspects of such systems have been largely overlooked. Namely, the transmission probability used during the cluster formation phase and the way in which cluster heads are selected. Both of these issues have an important impact on the performance of the system. For the former, it is common to consider that sensor nodes in a clustered-based Wireless Sensor Network (WSN) use a fixed transmission probability to send control data in order to build the clusters. However, due to the highly variable conditions experienced by these networks, a fixed transmission probability may lead to extra energy consumption. In view of this, three different transmission probability strategies are studied: optimal, fixed and adaptive. In this context, we also investigate cluster head selection schemes, specifically, we consider two intelligent schemes based on the fuzzy C-means and k-medoids algorithms and a random selection with no intelligence. We show that the use of intelligent schemes greatly improves the performance of the system, but their use entails higher complexity and selection delay. The main performance metrics considered in this work are energy consumption, successful transmission probability and cluster formation latency. As an additional feature of this work, we study the effect of errors in the wireless channel and the impact on the performance of the system under the different transmission probability schemes.

Performance Analysis of Cluster Formation in Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Edgar Romo Montiel

2017-12-01

Full Text Available Clustered-based wireless sensor networks have been extensively used in the literature in order to achieve considerable energy consumption reductions. However, two aspects of such systems have been largely overlooked. Namely, the transmission probability used during the cluster formation phase and the way in which cluster heads are selected. Both of these issues have an important impact on the performance of the system. For the former, it is common to consider that sensor nodes in a clustered-based Wireless Sensor Network (WSN use a fixed transmission probability to send control data in order to build the clusters. However, due to the highly variable conditions experienced by these networks, a fixed transmission probability may lead to extra energy consumption. In view of this, three different transmission probability strategies are studied: optimal, fixed and adaptive. In this context, we also investigate cluster head selection schemes, specifically, we consider two intelligent schemes based on the fuzzy C-means and k-medoids algorithms and a random selection with no intelligence. We show that the use of intelligent schemes greatly improves the performance of the system, but their use entails higher complexity and selection delay. The main performance metrics considered in this work are energy consumption, successful transmission probability and cluster formation latency. As an additional feature of this work, we study the effect of errors in the wireless channel and the impact on the performance of the system under the different transmission probability schemes.

Evaluation of SAR in a human body model due to wireless power transmission in the 10 MHz band.

Science.gov (United States)

Laakso, Ilkka; Tsuchida, Shogo; Hirata, Akimasa; Kamimura, Yoshitsugu

2012-08-07

This study discusses a computational method for calculating the specific absorption rate (SAR) due to a wireless power transmission system in the 10 MHz frequency band. A two-step quasi-static method comprised of the method of moments and the scalar potential finite-difference method are proposed. The applicability of the quasi-static approximation for localized exposure in this frequency band is discussed by comparing the SAR in a lossy dielectric cylinder computed with a full-wave electromagnetic analysis and the quasi-static approximation. From the computational results, the input impedance of the resonant coils was affected by the existence of the cylinder. On the other hand, the magnetic field distribution in free space and considering the cylinder and an impedance matching circuit were in good agreement; the maximum difference in the amplitude of the magnetic field was 4.8%. For a cylinder-coil distance of 10 mm, the difference between the peak 10 g averaged SAR in the cylinder computed with the full-wave electromagnetic method and our quasi-static method was 7.8%. These results suggest that the quasi-static approach is applicable for conducting the dosimetry of wireless power transmission in the 10 MHz band. With our two-step quasi-static method, the SAR in the anatomically based model was computed for different exposure scenarios. From those computations, the allowable input power satisfying the limit of a peak 10 g averaged SAR of 2.0 W kg(-1) was 830 W in the worst case exposure scenario with a coil positioned at a distance of 30 mm from the chest.

Reactor building indoor wireless network channel quality estimation using RSSI measurement of wireless sensor network

International Nuclear Information System (INIS)

Merat, S.

2008-01-01

Expanding wireless communication network reception inside reactor buildings (RB) and service wings (SW) has always been a technical challenge for operations service team. This is driven by the volume of metal equipment inside the Reactor Buildings (RB) that blocks and somehow shields the signal throughout the link. In this study, to improve wireless reception inside the Reactor Building (RB), an experimental model using indoor localization mesh based on IEEE 802.15 is developed to implement a wireless sensor network. This experimental model estimates the distance between different nodes by measuring the RSSI (Received Signal Strength Indicator). Then by using triangulation and RSSI measurement, the validity of the estimation techniques is verified to simulate the physical environmental obstacles, which block the signal transmission. (author)

Reactor building indoor wireless network channel quality estimation using RSSI measurement of wireless sensor network

Energy Technology Data Exchange (ETDEWEB)

Merat, S. [Wardrop Engineering Inc., Toronto, Ontario (Canada)

2008-07-01

Expanding wireless communication network reception inside reactor buildings (RB) and service wings (SW) has always been a technical challenge for operations service team. This is driven by the volume of metal equipment inside the Reactor Buildings (RB) that blocks and somehow shields the signal throughout the link. In this study, to improve wireless reception inside the Reactor Building (RB), an experimental model using indoor localization mesh based on IEEE 802.15 is developed to implement a wireless sensor network. This experimental model estimates the distance between different nodes by measuring the RSSI (Received Signal Strength Indicator). Then by using triangulation and RSSI measurement, the validity of the estimation techniques is verified to simulate the physical environmental obstacles, which block the signal transmission. (author)

Wireless power transmission to an electromechanical receiver using low-frequency magnetic fields

International Nuclear Information System (INIS)

Challa, Vinod R; Arnold, David P; Mur-Miranda, Jose Oscar

2012-01-01

A near-field, electrodynamically coupled wireless power transmission system is presented that delivers electrical power from a transmitter coil to a compact electromechanical receiver. The system integrates electromechanical energy conversion and mechanical resonance to deliver power over a range of distances using low-amplitude, low-frequency magnetic fields. Two different receiver orientations are investigated that rely on either the force or the torque induced on the receiver magnet at separation distances ranging from 2.2 to 10.2 cm. Theoretical models for each mode compare the predicted performance with the experimental results. For a 7.1 mA pk sinusoidal current supplied to a transmitter coil with a 100 cm diameter, the torque mode receiver orientation has a maximum power transfer of 150 μW (efficiency of 12%) at 2.2 cm at its resonance frequency of 38.4 Hz. For the same input current to the transmitter, the force mode receiver orientation has a maximum power transfer of 37 μW (efficiency of 4.1%) at 3.1 cm at its resonance frequency of 38.9 Hz. (paper)

Psychological consequences of aggression in pre-hospital emergency care: cross sectional survey.

Science.gov (United States)

Bernaldo-De-Quirós, Mónica; Piccini, Ana T; Gómez, M Mar; Cerdeira, Jose C

2015-01-01

Pre-hospital emergency care is a particularly vulnerable setting for workplace violence. However, there is no literature available to date on the psychological consequences of violence in pre-hospital emergency care. To evaluate the psychological consequences of exposure to workplace violence from patients and those accompanying them in pre-hospital emergency care. A retrospective cross-sectional study. 70 pre-hospital emergency care services located in Madrid region. A randomized sample of 441 health care workers (135 physicians, 127 nurses and 179 emergency care assistants). Data were collected from February to May 2012. The survey was divided into four sections: demographic/professional information, level of burnout determined by Maslach Burnout Inventory (MBI), mental health status using General Health Questionnaire (GHQ-28) and frequency and type of violent behaviour experienced by staff members. The health care professionals who had been exposed to physical and verbal violence presented a significantly higher percentage of anxiety, emotional exhaustion, depersonalization and burnout syndrome compared with those who had not been subjected to any aggression. Frequency of verbal violence (more than five times) was related to emotional exhaustion and depersonalization. Type of violence (i.e. physical aggression) is especially related to high anxiety levels and frequency of verbal aggression is associated with burnout (emotional exhaustion and depersonalization). Psychological counselling should be made available to professional staff who have been subjected to physical aggression or frequent verbal violence. Copyright © 2014 Elsevier Ltd. All rights reserved.

Wireless Communications for Monitoring Nuclear Material Processes part 1.: Context and Technologies

International Nuclear Information System (INIS)

Braina, F.; Goncalves, J.C.M.; Versino, C.; Heppleston, M.; Schoeneman, B.; Tolk, K.

2007-01-01

Recent advances in radio frequency communication technologies offer the motivation to consider the use of wireless communication in nuclear safeguards applications. From the Nuclear Safeguards Inspectorate' (NSI) point of view, wireless data transmission, which would be supplemental to wired communication is attractive for the ease of installation and the ability to respond to the changing requirements as the inspection approach evolves, resulting in a reduction of costs. However, for wireless technologies to be considered as a viable complement to cables, a number of concerns have to be addressed. First, nuclear operators need to be guaranteed that RF transmission will not interfere with the facilities safety and physical security systems. On their side, the NSI must be satisfied that Containment and Surveillance equipment and data transmission processes will not be affected by the other existing RF equipment. Second, it is desirable, both for the NSI and the operators, that the data being transmitted is not available for analysis by a third party. In addition, the NSI require data to be authenticated as close to the point of acquisition as possible. This paper was prepared as an account of work performed and approved by the ESARDA Working Group on Containment and Surveillance. It is the first of a suite dedicated to bridging RF technologies with safeguards monitoring applications. The paper focuses on technological issues: it introduces basic concepts underlying wireless communication, including methods for transmission, issues on power consumption, frequency, range, and considerations on interference and noise resilience. It overviews state-of-the-art wireless technologies and presents a projection on wireless capabilities that are likely to be reached in the near future

Transmission of Pneumocystis carinii from patients to hospital staff

DEFF Research Database (Denmark)

Lundgren, Bettina; Elvin, K; Rothman, L P

1997-01-01

rooms in departments of infectious diseases managing patients with P carinii pneumonia (PCP), suggesting the airborne route of transmission. Exposure of staff to P carinii may occur in hospital departments treating patients with PCP. METHODS: Exposure to P carinii was detected by serological responses...... to human P carinii by ELISA, Western blotting, and indirect immunofluorescence in 64 hospital staff with and 79 staff without exposure to patients with PCP from Denmark and Sweden. DNA amplification of oropharyngeal washings was performed on 20 Danish staff with and 20 staff without exposure to patients...... with PCP. RESULTS: There was no significant difference in the frequency or level of antibodies to P carinii between staff exposed and those unexposed to patients with PCP. None of the hospital staff had detectable P carinii DNA in oropharyngeal washings. CONCLUSIONS: There is no difference in antibodies...

Artificial intelligence in wireless communications

CERN Document Server

Rondeau, Thomas W

2009-01-01

This cutting-edge resource offers practical overview of cognitive radio, a paradigm for wireless communications in which a network or a wireless node changes its transmission or reception parameters. The alteration of parameters is based on the active monitoring of several factors in the external and internal radio environment. This book offers a detailed description of cognitive radio and its individual parts. Practitioners learn how the basic processing elements and their capabilities are implemented as modular components. Moreover, the book explains how each component can be developed and t

Temperature estimation of induction machines based on wireless sensor networks

Directory of Open Access Journals (Sweden)

Y. Huang

2018-04-01

Full Text Available In this paper, a fourth-order Kalman filter (KF algorithm is implemented in the wireless sensor node to estimate the temperatures of the stator winding, the rotor cage and the stator core in the induction machine. Three separate wireless sensor nodes are used as the data acquisition systems for different input signals. Six Hall sensors are used to acquire the three-phase stator currents and voltages of the induction machine. All of them are processed to root mean square (rms in ampere and volt. A rotary encoder is mounted for the rotor speed and Pt-1000 is used for the temperature of the coolant air. The processed signals in the physical unit are transmitted wirelessly to the host wireless sensor node, where the KF is implemented with fixed-point arithmetic in Contiki OS. Time-division multiple access (TDMA is used to make the wireless transmission more stable. Compared to the floating-point implementation, the fixed-point implementation has the same estimation accuracy at only about one-fifth of the computation time. The temperature estimation system can work under any work condition as long as there are currents through the machine. It can also be rebooted for estimation even when wireless transmission has collapsed or packages are missing.

Bluetooth low energy: wireless connectivity for medical monitoring.

Science.gov (United States)

Omre, Alf Helge

2010-03-01

Electronic wireless sensors could cut medical costs by enabling physicians to remotely monitor vital signs such as blood pressure, blood glucose, and blood oxygenation while patients remain at home. According to the IDC report "Worldwide Bluetooth Semiconductor 2008-2012 Forecast," published November 2008, a forthcoming radio frequency communication ("wireless connectivity") standard, Bluetooth low energy, will link wireless sensors via radio signals to the 70% of cell phones and computers likely to be fitted with the next generation of Bluetooth wireless technology, leveraging a ready-built infrastructure for data transmission. Analysis of trends indicated by this data can help physicians better manage diseases such as diabetes. The technology also addresses the concerns of cost, compatibility, and interoperability that have previously stalled widespread adoption of wireless technology in medical applications. (c) 2010 Diabetes Technology Society.

A wireless acoustic emission sensor remotely powered by light

International Nuclear Information System (INIS)

Zahedi, F; Huang, H

2014-01-01

In this paper, wireless sensing of acoustic emission (AE) signals using a battery-free sensor node remotely powered by light is presented. The wireless sensor consists of a piezoelectric wafer active sensor (PWAS) for AE signal acquisition and a wireless transponder that performs signal conditioning, frequency conversion, and wireless transmission. For signal conditioning, a voltage follower that consumes less than 2 mW was introduced to buffer the high impedance of the PWAS from the low impedance of the wireless transponder. A photocell-based energy harvester with a stable voltage output was developed to power the voltage follower so that the wireless AE sensor can operate without an external power source. The principle of operation of the battery-free wireless AE sensor node and the sensor interrogation system is described, followed by a detailed description of the hardware implementation. The voltage follower and the wireless channel were characterized by ultrasound pitch–catch and pencil lead break experiments. (paper)

Status of nosocomial tuberculosis transmission prevention in hospitals in Thailand.

Science.gov (United States)

Unahalekhaka, Akeau; Lueang-a-papong, Suchada; Chitreecheur, Jittaporn

2014-03-01

A national survey was conducted during July to September 2009 to determine tuberculosis (TB) prevention activities, problems, and support needed of Thai hospitals. Ninety-seven percent of hospitals established TB isolation policy, 96.3% provided guidelines for caring of TB patients, 95% and 91.8% provided prevention of TB transmission and environmental management guideline, and 92.6% established screening system for TB in the outpatient department (OPD). A half of hospitals had problems with isolation rooms and difficulties in screening TB cases in the OPD. Support needed included consultation on structure and ventilation systems, personnel training, national TB prevention, and TB screening guideline. Strengthening TB prevention activities, providing expert consultation, and national guidelines may help hospitals improve their TB prevention activities. Copyright © 2014 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Mosby, Inc. All rights reserved.

Scalable Video Streaming in Wireless Mesh Networks for Education

Science.gov (United States)

Liu, Yan; Wang, Xinheng; Zhao, Liqiang

2011-01-01

In this paper, a video streaming system for education based on a wireless mesh network is proposed. A wireless mesh network is a self-organizing, self-managing and reliable intelligent network, which allows educators to deploy a network quickly. Video streaming plays an important role in this system for multimedia data transmission. This new…

Wireless local network architecture for Naval medical treatment facilities

OpenAIRE

Deason, Russell C.

2004-01-01

Approved for public release; distribution is unlimited In today's Navy Medicine, an approach towards wireless networks is coming into view. The idea of developing and deploying workable Wireless Local Area Networks (WLAN) throughout Naval hospitals is but just a few years down the road. Currently Naval Medical Treatment Facilities (MTF) are using wired Local Area Networks (LANs) throughout the infrastructure of each facility. Civilian hospitals and other medical treatment facilities have b...

Local, distributed topology control for large-scale wireless ad-hoc networks

NARCIS (Netherlands)

Nieberg, T.; Hurink, Johann L.

In this document, topology control of a large-scale, wireless network by a distributed algorithm that uses only locally available information is presented. Topology control algorithms adjust the transmission power of wireless nodes to create a desired topology. The algorithm, named local power

Battery-less wireless interrogation of microstrip patch antenna for strain sensing

International Nuclear Information System (INIS)

Xu, X; Huang, H

2012-01-01

This paper presents a battery-less wireless interrogation system that can measure the resonant frequency of a microstrip patch antenna with a fine resolution. Since the antenna resonant frequency is sensitive to strain-induced deformations, wireless interrogation of the antenna sensor for strain measurement was demonstrated. By implementing a microwatt impedance switching circuit at the sensor node, the antenna backscattering is amplitude modulated at the sensor node so that it can be separated from the structural backscattering at the interrogator. The sensor node can be powered by a small photocell and thus achieve battery-less operation. The operating principle of the wireless interrogation system is first described, followed by the implementation and characterization of the wireless interrogation system. The antenna resonant frequency shifts were correlated to the applied strains through a static tensile experiment. An excellent agreement between the experimental results and the analytical prediction was obtained. A power transmission model was established and validated with experimental measurements. Based on this power transmission model, we estimated that the maximum interrogation distance of the wireless strain measurement system is 26 m. (paper)

THE EFFECT OF STORYTELLING IN A PLAY THERAPY ON ANXIETY LEVEL IN PRE-SCHOOL CHILDREN DURING HOSPITALIZATION IN THE GENERAL HOSPITAL OF BUTON

Directory of Open Access Journals (Sweden)

Mimi Yati

2017-09-01

Full Text Available Background: Anxiety is one of the psychical stresses experienced by children during hospitalization. A storytelling in a play therapy is considered effective in reducing anxiety. Objective: This study aims to determine the effect of storytelling in a play therapy on anxiety level in pre-school children during hospitalization in the general hospital of Buton. Methods: This was a quasy-experimental study with pretest-posttest control group design. There were 30 pre-school children selected in this study using accidental sampling, with 15 assigned in each group. The Pre School - Spence Children’s Anxiety Scale (SCAS was used to measure anxiety in pre-school children. Wilcoxon matched paired test was used to analyze the data. Results: Findings showed that the mean of anxiety level in the intervention group in pretest was 42 and in posttest was 31.53. Wilcoxon matched paired test showed p-value 0.003 (<0.05, which indicated that there was a statistically significant effect of storytelling on the level of anxiety in pre-school children. Conclusions: There is a significant influence of storytelling in a play therapy on anxiety levels in pre school children during hospitalization. It is suggested that this intervention could be applied as a nursing intervention to reduce anxiety in children.

A validation of ground ambulance pre-hospital times modeled using geographic information systems.

Science.gov (United States)

Patel, Alka B; Waters, Nigel M; Blanchard, Ian E; Doig, Christopher J; Ghali, William A

2012-10-03

Evaluating geographic access to health services often requires determining the patient travel time to a specified service. For urgent care, many research studies have modeled patient pre-hospital time by ground emergency medical services (EMS) using geographic information systems (GIS). The purpose of this study was to determine if the modeling assumptions proposed through prior United States (US) studies are valid in a non-US context, and to use the resulting information to provide revised recommendations for modeling travel time using GIS in the absence of actual EMS trip data. The study sample contained all emergency adult patient trips within the Calgary area for 2006. Each record included four components of pre-hospital time (activation, response, on-scene and transport interval). The actual activation and on-scene intervals were compared with those used in published models. The transport interval was calculated within GIS using the Network Analyst extension of Esri ArcGIS 10.0 and the response interval was derived using previously established methods. These GIS derived transport and response intervals were compared with the actual times using descriptive methods. We used the information acquired through the analysis of the EMS trip data to create an updated model that could be used to estimate travel time in the absence of actual EMS trip records. There were 29,765 complete EMS records for scene locations inside the city and 529 outside. The actual median on-scene intervals were longer than the average previously reported by 7-8 minutes. Actual EMS pre-hospital times across our study area were significantly higher than the estimated times modeled using GIS and the original travel time assumptions. Our updated model, although still underestimating the total pre-hospital time, more accurately represents the true pre-hospital time in our study area. The widespread use of generalized EMS pre-hospital time assumptions based on US data may not be appropriate in a

Association between use of pre-hospital ECG and 30-day mortality: A large cohort study of patients experiencing chest pain.

Science.gov (United States)

Rawshani, Nina; Rawshani, Araz; Gelang, Carita; Herlitz, Johan; Bång, Angela; Andersson, Jan-Otto; Gellerstedt, Martin

2017-12-01

In the assessment of patients with chest pain, there is support for the use of pre-hospital ECG in the literature and in the care guidelines. Using propensity score methods, we aim to examine whether the mere acquisition of a pre-hospital ECG among patients with chest pain affects the outcome (30-day mortality). The association between pre-hospital ECG and 30-day mortality was studied in the overall cohort (n=13151), as well as in the one-to-one matched cohort with 2524 patients not examined with pre-hospital ECG and 2524 patients examined with pre-hospital ECG. In the overall cohort, 21% (n=2809) did not undergo an ECG tracing in the pre-hospital setting. Among those who had pain during transport, 14% (n=1159) did not undergo a pre-hospital ECG while 32% (n=1135) of those who did not have pain underwent an ECG tracing. In the overall cohort, the OR for 30-day mortality in patients who had a pre-hospital ECG, as compared with those who did not, was 0.63 (95% CI 0.05-0.79; pECG was used. The PH-ECG is underused among patients with chest discomfort and the mere acquisition of a pre-hospital ECG may reduce mortality. Copyright © 2017 Elsevier B.V. All rights reserved.

Reliable low-power wireless networks over unstable transmission power

NARCIS (Netherlands)

Kotian, Roshan; Exarchakos, Georgios; Liotta, Antonio

2017-01-01

Internet of Things promises large scale interconnected sensing and actuation capabilities in domains, areas, applications and activities never accessed before by Internet. Besides other technical barriers, wireless network node lifetime impedes its applicability. To reduce the energy cost incurred

A Reliable Wireless Control System for Tomato Hydroponics.

Science.gov (United States)

Ibayashi, Hirofumi; Kaneda, Yukimasa; Imahara, Jungo; Oishi, Naoki; Kuroda, Masahiro; Mineno, Hiroshi

2016-05-05

Agricultural systems using advanced information and communication (ICT) technology can produce high-quality crops in a stable environment while decreasing the need for manual labor. The system collects a wide variety of environmental data and provides the precise cultivation control needed to produce high value-added crops; however, there are the problems of packet transmission errors in wireless sensor networks or system failure due to having the equipment in a hot and humid environment. In this paper, we propose a reliable wireless control system for hydroponic tomato cultivation using the 400 MHz wireless band and the IEEE 802.15.6 standard. The 400 MHz band, which is lower than the 2.4 GHz band, has good obstacle diffraction, and zero-data-loss communication is realized using the guaranteed time-slot method supported by the IEEE 802.15.6 standard. In addition, this system has fault tolerance and a self-healing function to recover from faults such as packet transmission failures due to deterioration of the wireless communication quality. In our basic experiments, the 400 MHz band wireless communication was not affected by the plants' growth, and the packet error rate was less than that of the 2.4 GHz band. In summary, we achieved a real-time hydroponic liquid supply control with no data loss by applying a 400 MHz band WSN to hydroponic tomato cultivation.

A Reliable Wireless Control System for Tomato Hydroponics

Science.gov (United States)

Ibayashi, Hirofumi; Kaneda, Yukimasa; Imahara, Jungo; Oishi, Naoki; Kuroda, Masahiro; Mineno, Hiroshi

2016-01-01

Agricultural systems using advanced information and communication (ICT) technology can produce high-quality crops in a stable environment while decreasing the need for manual labor. The system collects a wide variety of environmental data and provides the precise cultivation control needed to produce high value-added crops; however, there are the problems of packet transmission errors in wireless sensor networks or system failure due to having the equipment in a hot and humid environment. In this paper, we propose a reliable wireless control system for hydroponic tomato cultivation using the 400 MHz wireless band and the IEEE 802.15.6 standard. The 400 MHz band, which is lower than the 2.4 GHz band, has good obstacle diffraction, and zero-data-loss communication is realized using the guaranteed time-slot method supported by the IEEE 802.15.6 standard. In addition, this system has fault tolerance and a self-healing function to recover from faults such as packet transmission failures due to deterioration of the wireless communication quality. In our basic experiments, the 400 MHz band wireless communication was not affected by the plants’ growth, and the packet error rate was less than that of the 2.4 GHz band. In summary, we achieved a real-time hydroponic liquid supply control with no data loss by applying a 400 MHz band WSN to hydroponic tomato cultivation. PMID:27164105

Wireless Power Transfer Impact on Data Channel

OpenAIRE

Baikova, Elena N.; Valtchev, Stanimir S.; Melício, R.; Fernão Pires, V.

2016-01-01

Trabalho apresentado no 23rd International Symposium on Power Electronics, Electrical Drives, Automation and Motion (Speedam, 2016), 22-24 junho de 2016, Capri, Itália This paper presents measurement results and analysis of the interference produced by the high-power electromagnetic field in a wireless energy transfer system. Through this analysis it is expected to be possible to evaluate the influence of the strong electromagnetic field on the data transmission channel. The wireless power...

Transmission power control for wireless home and building automation

NARCIS (Netherlands)

Bacchiani, C.

2015-01-01

Home and building automation can provide significant improvements in comfort and energy efficiency of buildings. However, its diffusion is hindered by the complexity of installation and maintenance. Wireless connectivity can simplify this process, reducing installation time and cost, but it requires

A Fully Integrated Wireless Compressed Sensing Neural Signal Acquisition System for Chronic Recording and Brain Machine Interface.

Science.gov (United States)

Liu, Xilin; Zhang, Milin; Xiong, Tao; Richardson, Andrew G; Lucas, Timothy H; Chin, Peter S; Etienne-Cummings, Ralph; Tran, Trac D; Van der Spiegel, Jan

2016-07-18

Reliable, multi-channel neural recording is critical to the neuroscience research and clinical treatment. However, most hardware development of fully integrated, multi-channel wireless neural recorders to-date, is still in the proof-of-concept stage. To be ready for practical use, the trade-offs between performance, power consumption, device size, robustness, and compatibility need to be carefully taken into account. This paper presents an optimized wireless compressed sensing neural signal recording system. The system takes advantages of both custom integrated circuits and universal compatible wireless solutions. The proposed system includes an implantable wireless system-on-chip (SoC) and an external wireless relay. The SoC integrates 16-channel low-noise neural amplifiers, programmable filters and gain stages, a SAR ADC, a real-time compressed sensing module, and a near field wireless power and data transmission link. The external relay integrates a 32 bit low-power microcontroller with Bluetooth 4.0 wireless module, a programming interface, and an inductive charging unit. The SoC achieves high signal recording quality with minimized power consumption, while reducing the risk of infection from through-skin connectors. The external relay maximizes the compatibility and programmability. The proposed compressed sensing module is highly configurable, featuring a SNDR of 9.78 dB with a compression ratio of 8×. The SoC has been fabricated in a 180 nm standard CMOS technology, occupying 2.1 mm × 0.6 mm silicon area. A pre-implantable system has been assembled to demonstrate the proposed paradigm. The developed system has been successfully used for long-term wireless neural recording in freely behaving rhesus monkey.

Facilitators and obstacles in pre-hospital medical response to earthquakes: a qualitative study

Science.gov (United States)

2011-01-01

Background Earthquakes are renowned as being amongst the most dangerous and destructive types of natural disasters. Iran, a developing country in Asia, is prone to earthquakes and is ranked as one of the most vulnerable countries in the world in this respect. The medical response in disasters is accompanied by managerial, logistic, technical, and medical challenges being also the case in the Bam earthquake in Iran. Our objective was to explore the medical response to the Bam earthquake with specific emphasis on pre-hospital medical management during the first days. Methods The study was performed in 2008; an interview based qualitative study using content analysis. We conducted nineteen interviews with experts and managers responsible for responding to the Bam earthquake, including pre-hospital emergency medical services, the Red Crescent, and Universities of Medical Sciences. The selection of participants was determined by using a purposeful sampling method. Sample size was given by data saturation. Results The pre-hospital medical service was divided into three categories; triage, emergency medical care and transportation, each category in turn was identified into facilitators and obstacles. The obstacles identified were absence of a structured disaster plan, absence of standardized medical teams, and shortage of resources. The army and skilled medical volunteers were identified as facilitators. Conclusions The most compelling, and at the same time amenable obstacle, was the lack of a disaster management plan. It was evident that implementing a comprehensive plan would not only save lives but decrease suffering and enable an effective praxis of the available resources at pre-hospital and hospital levels. PMID:21575233

Facilitators and obstacles in pre-hospital medical response to earthquakes: a qualitative study.

Science.gov (United States)

Djalali, Ahmadreza; Khankeh, Hamidreza; Öhlén, Gunnar; Castrén, Maaret; Kurland, Lisa

2011-05-16

Earthquakes are renowned as being amongst the most dangerous and destructive types of natural disasters. Iran, a developing country in Asia, is prone to earthquakes and is ranked as one of the most vulnerable countries in the world in this respect. The medical response in disasters is accompanied by managerial, logistic, technical, and medical challenges being also the case in the Bam earthquake in Iran. Our objective was to explore the medical response to the Bam earthquake with specific emphasis on pre-hospital medical management during the first days. The study was performed in 2008; an interview based qualitative study using content analysis. We conducted nineteen interviews with experts and managers responsible for responding to the Bam earthquake, including pre-hospital emergency medical services, the Red Crescent, and Universities of Medical Sciences. The selection of participants was determined by using a purposeful sampling method. Sample size was given by data saturation. The pre-hospital medical service was divided into three categories; triage, emergency medical care and transportation, each category in turn was identified into facilitators and obstacles. The obstacles identified were absence of a structured disaster plan, absence of standardized medical teams, and shortage of resources. The army and skilled medical volunteers were identified as facilitators. The most compelling, and at the same time amenable obstacle, was the lack of a disaster management plan. It was evident that implementing a comprehensive plan would not only save lives but decrease suffering and enable an effective praxis of the available resources at pre-hospital and hospital levels.

Effect of a comprehensive health education program on pre-hospital delay intentions in high-risk stroke population and caregivers.

Science.gov (United States)

Yang, Li; Zhao, Qiuli; Zhu, Xuemei; Shen, Xiaoying; Zhu, Yulan; Yang, Liu; Gao, Wei; Li, Minghui

2017-08-01

Many factors influence pre-hospital delays in the event of stroke. This study aimed to develop and evaluate a comprehensive educational program for decreasing pre-hospital delays in high-risk stroke population. We enrolled 220 high-risk stroke population and caregivers from six urban communities in Harbin from May 2013 to May 2015, and randomly divided them into intervention and control groups. We implemented a comprehensive educational program (intervention group), comprising public lectures, instructional brochures, case videos, simulations, and role-playing from May 2013 to May 2015. We delivered conventional oral education in the control group. We compared stroke pre-hospital delay behavioral intention (SPDBI), pre-hospital stroke symptom coping test (PSSCT), and stroke pre-symptoms alert test (SPSAT) results between the groups before and 6, 12, and 18 months after health intervention. There were significant differences between before and after intervention (P educational program was significantly effective in decreasing SPDBI, improving knowledge, enhancing stroke pre-symptoms alert, and reducing the possibility of pre-hospital delays.

IP communication optimization for 6LoWPAN-Based Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Li MA

2014-07-01

Full Text Available The emergence of 6LoWPAN makes it possible that Wireless Sensor Networks access to the Internet. However, the cost of IP communication between 6LoWPAN wireless sensor node and external internet node is still relatively high. This paper proposed a new addressing configuration and compression scheme in 6LoWPAN network called IPHC-NAT, which largely reduced the proportion of the IP header in 6LoWPAN packet, designed and constructed a bidirectional data transmission gateway to connect 6LoWPAN wireless sensor node with IPv6 client. The experimental results show the feasibility of the design of IPHC-NAT and the data transmission efficiency has significantly been improved compared to the original 6LoWPAN network.

Pre-hospital Management of the Fractured Femur Using the ...

African Journals Online (AJOL)

Two aspects of the early management of the fractured femur are discussed: firstly the immediate treatment in the pre-hospital phase and secondly the transportation of this injury case over a long distance where necessary. In both instances there is considerable room for improvement, and this is discussed, particularly with ...

Performance enhancement of multi-core fiber transmission using real-time FPGA based pre-emphasis

NARCIS (Netherlands)

Hasanuzzaman, G. K.M.; Spolitis, S.; Salgals, T.; Braunfelds, J.; Morales, A.; Gonzalez, L. E.; Rommel, S.; Puerta, R.; Asensio, P.; Bobrovs, V.; Iezekiel, S.; Tafur Monroy, I.

2017-01-01

We experimentally demonstrate pre-emphasis based performance for a 2 km long 7-core multicore fiber link. Simultaneous transmission below the FEC threshold is achievable for all cores by using signal equalization in a FPGA.

Development and application of a modified wireless tracer for disaster prevention

Science.gov (United States)

Chung Yang, Han; Su, Chih Chiang

2016-04-01

Typhoon-induced flooding causes water overflow in a river channel, which results in general and bridge scour and soil erosion, thus leading to bridge failure, debris flow and landslide collapse. Therefore, dynamic measurement technology should be developed to assess scour in channels and landslide as a disaster-prevention measure against bridge failure and debris flow. This paper presents a wireless tracer that enables monitoring general scour in river channels and soil erosion in hillsides. The wireless tracer comprises a wireless high-power radio modem, various electronic components, and a self-designed printed circuit board that are all combined with a 9-V battery pack and an auto switch. The entire device is sealed in a jar by silicon. After it was modified, the wireless tracer underwent the following tests for practical applications: power continuation and durability, water penetration, and signal transmission during floating. A regression correlation between the wireless tracer's transmission signal and distance was also established. This device can be embedded at any location where scouring is monitored, and, in contrast to its counterparts that detect scour depth by identifying and analyzing received signals, it enables real-time observation of the scouring process. In summary, the wireless tracer developed in this study provides a dynamic technology for real-time monitoring of scouring (or erosion) and forecasting of landslide hazards. Keywords: wireless tracer; scour; real-time monitoring; landslide hazard.

Evaluation of SAR in a human body model due to wireless power transmission in the 10 MHz band

International Nuclear Information System (INIS)

Laakso, Ilkka; Tsuchida, Shogo; Hirata, Akimasa; Kamimura, Yoshitsugu

2012-01-01

This study discusses a computational method for calculating the specific absorption rate (SAR) due to a wireless power transmission system in the 10 MHz frequency band. A two-step quasi-static method comprised of the method of moments and the scalar potential finite-difference method are proposed. The applicability of the quasi-static approximation for localized exposure in this frequency band is discussed by comparing the SAR in a lossy dielectric cylinder computed with a full-wave electromagnetic analysis and the quasi-static approximation. From the computational results, the input impedance of the resonant coils was affected by the existence of the cylinder. On the other hand, the magnetic field distribution in free space and considering the cylinder and an impedance matching circuit were in good agreement; the maximum difference in the amplitude of the magnetic field was 4.8%. For a cylinder–coil distance of 10 mm, the difference between the peak 10 g averaged SAR in the cylinder computed with the full-wave electromagnetic method and our quasi-static method was 7.8%. These results suggest that the quasi-static approach is applicable for conducting the dosimetry of wireless power transmission in the 10 MHz band. With our two-step quasi-static method, the SAR in the anatomically based model was computed for different exposure scenarios. From those computations, the allowable input power satisfying the limit of a peak 10 g averaged SAR of 2.0 W kg −1 was 830 W in the worst case exposure scenario with a coil positioned at a distance of 30 mm from the chest. (paper)

The security energy encryption in wireless power transfer

Science.gov (United States)

Sadzali, M. N.; Ali, A.; Azizan, M. M.; Albreem, M. A. M.

2017-09-01

This paper presents a concept of security in wireless power transfer (WPT) by applying chaos theory. Chaos theory is applied as a security system in order to safeguard the transfer of energy from a transmitter to the intended receiver. The energy encryption of the wireless power transfer utilizes chaos theory to generate the possibility of a logistic map for the chaotic security key. The simulation for energy encryption wireless power transfer system was conducted by using MATLAB and Simulink. By employing chaos theory, the chaotic key ensures the transmission of energy from transmitter to its intended receiver.

Radio over fiber for wireless communications from fundamentals to advanced topics

CERN Document Server

Fernando, Xavier N

2014-01-01

A comprehensive evaluation of Fi-Wi,  enabling readers to design links using channel estimation and equalization algorithms  This book provides a detailed study of radio over fiber (ROF) based wireless communication systems, otherwise called fiber wireless (Fi-Wi) systems. This is an emerging hot topic where the abundant bandwidth of optical fiber is directly combined with the flexibility and mobility of wireless networks to provide broadband connectivity.  Its application is increasing because of the growing demand for broadband wireless services. In such a system the transmission of the ra

Radiation area monitoring by wireless-communicating area monitor with surveillance camera

International Nuclear Information System (INIS)

Shimura, Mitsuo; Kobayashi, Hiromitsu; Kitahara, Hideki; Kobayashi, Hironobu; Okamoto, Shinji

2004-01-01

Aiming at a dose reduction and a work efficiency improvement for nuclear power plants that have high dose regions, we have developed our system of wireless-communicating Area Monitor with Surveillance Camera, and have performed an on-site test. Now we are implementing this Area Monitor with Surveillance Camera for a use as a TV camera in the controlled-area, which enables a personal computer to simultaneously display two or more dose values and site live images on the screen. For the radiation detector of this Area Monitor System, our wireless-communicating dosimeter is utilized. Image data are transmitted via a wireless Local Area Network (LAN). As a test result, image transmission of a maximum of 20 frames per second has been realized, which shows that this concept is a practical application. Remote-site monitoring also has been realized from an office desk located within the non-controlled area, adopting a Japan's wireless phone system, PHS (Personal Handy Phone) for the transmission interface. (author)

Single-Carrier Dual-Polarization 328-Gb/s Wireless Transmission in a D-Band Millimeter Wave 2 x 2 MU-MIMO Radio-Over-Fiber System

DEFF Research Database (Denmark)

Puerta, Rafael; Yu, Jianjun; Li, Xinying

2018-01-01

Next generation wireless communication systems face many challenges to increase the capacity and spectral efficiency of current solutions. The worldwide mobile data traffic increased 4000-fold over the last decade, and is forecast a 7-fold increase between 2016 and 2021. To cope with these string......Next generation wireless communication systems face many challenges to increase the capacity and spectral efficiency of current solutions. The worldwide mobile data traffic increased 4000-fold over the last decade, and is forecast a 7-fold increase between 2016 and 2021. To cope...... with these stringent demands, prospective solutions are millimeter-wave (mmWave) technology and ultradense small cell networks, given that today most of the mobile traffic is offloaded from mobile networks, i.e., most of mobile users are connected to fixed networks. In addition, enabled by the fast development...... of electronics, digital signal processing has become essential to enhance the capacity and the performance of current communication systems. In this paper, by using the benefits of multiband modulation schemes and independent sideband (ISB) modulation, high-speed mmWave wireless transmissions in the D-band (110...

A Power Balance Aware Wireless Charger Deployment Method for Complete Coverage in Wireless Rechargeable Sensor Networks

Directory of Open Access Journals (Sweden)

Tu-Liang Lin

2016-08-01

Full Text Available Traditional sensor nodes are usually battery powered, and the limited battery power constrains the overall lifespan of the sensors. Recently, wireless power transmission technology has been applied in wireless sensor networks (WSNs to transmit wireless power from the chargers to the sensor nodes and solve the limited battery power problem. The combination of wireless sensors and wireless chargers forms a new type of network called wireless rechargeable sensor networks (WRSNs. In this research, we focus on how to effectively deploy chargers to maximize the lifespan of a network. In WSNs, the sensor nodes near the sink consume more power than nodes far away from the sink because of frequent data forwarding. This important power unbalanced factor has not been considered, however, in previous charger deployment research. In this research, a power balance aware deployment (PBAD method is proposed to address the power unbalance in WRSNs and to design the charger deployment with maximum charging efficiency. The proposed deployment method is effectively aware of the existence of the sink node that would cause unbalanced power consumption in WRSNs. The simulation results show that the proposed PBAD algorithm performs better than other deployment methods, and fewer chargers are deployed as a result.

Low-power wireless infrared communications

NARCIS (Netherlands)

Otte, R.; Jong, de L.P.; Roermund, van A.H.M.

1999-01-01

Today, wireless infrared transmission has entered our homes, offices, industry and health care, with applications in the field of remote control, telemetry, and local communication. This book is about the underlying technology. As it is an outgrowth of my Ph.D. thesis, the emphasis is on fundamental

BTP: a Block Transfer Protocol for Delay Tolerant Wireless Sensor Networks

DEFF Research Database (Denmark)

Hansen, Morten Tranberg; Biagioni, Edoardo S.

2010-01-01

Wireless sensor networks that are energy-constrained must transmit and receive data as efficiently as possible.  If the transmission is delay tolerant, transferring blocks of accumulated data can be more efficient than transferring each sensed measurement as soon as it is available.  This paper...... proposes a Block Transfer Protocol (BTP) designed for efficient and reliable transmission in wireless sensor networks.  BTP reduces the time it takes to reliably transfer a block of packets compared to conventional link layer protocols, by piggybacking in data packets information about the transfer......, minimizing the number of acknowledgements needed for reliable transmission, and reducing the need for timeouts, which can substantially slow down communication when transmission is unreliable.  In addition, BTP improves reliability by handling false positive acknowledgements and by letting the receivers...

Wireless battery management control and monitoring system

Science.gov (United States)

Zumstein, James M.; Chang, John T.; Farmer, Joseph C.; Kovotsky, Jack; Lavietes, Anthony; Trebes, James Edward

2018-01-16

A battery management system using a sensor inside of the battery that sensor enables monitoring and detection of various events in the battery and transmission of a signal from the sensor through the battery casing to a control and data acquisition module by wireless transmission. The detection of threshold events in the battery enables remedial action to be taken to avoid catastrophic events.

WiMax taking wireless to the max

CERN Document Server

Pareek, Deepak

2006-01-01

With market value expected to reach 5 billion by 2007 and the endorsement of some of the biggest names in telecommunications, World Interoperability for Microwave Access (WiMAX) is poised to change the broadband wireless landscape. But how much of WiMAX's touted potential is merely hype? Now that several pre-WiMAX networks have been deployed, what are the operators saying about QoS and ROI? How and when will device manufacturers integrate WiMAX into their products? What is the business case for using WiMAX rather than any number of other established wireless alternatives?WiMAX: Taking Wireless

Energy neutral and low power wireless communications

Science.gov (United States)

Orhan, Oner

Wireless sensor nodes are typically designed to have low cost and small size. These design objectives impose restrictions on the capacity and efficiency of the transceiver components and energy storage units that can be used. As a result, energy becomes a bottleneck and continuous operation of the sensor network requires frequent battery replacements, increasing the maintenance cost. Energy harvesting and energy efficient transceiver architectures are able to overcome these challenges by collecting energy from the environment and utilizing the energy in an intelligent manner. However, due to the nature of the ambient energy sources, the amount of useful energy that can be harvested is limited and unreliable. Consequently, optimal management of the harvested energy and design of low power transceivers pose new challenges for wireless network design and operation. The first part of this dissertation is on energy neutral wireless networking, where optimal transmission schemes under different system setups and objectives are investigated. First, throughput maximization for energy harvesting two-hop networks with decode-and-forward half-duplex relays is studied. For a system with two parallel relays, various combinations of the following four transmission modes are considered: Broadcast from the source, multi-access from the relays, and successive relaying phases I and II. Next, the energy cost of the processing circuitry as well as the transmission energy are taken into account for communication over a broadband fading channel powered by an energy harvesting transmitter. Under this setup, throughput maximization, energy maximization, and transmission completion time minimization problems are studied. Finally, source and channel coding for an energy-limited wireless sensor node is investigated under various energy constraints including energy harvesting, processing and sampling costs. For each objective, optimal transmission policies are formulated as the solutions of a

A Hybrid Data Compression Scheme for Power Reduction in Wireless Sensors for IoT.

Science.gov (United States)

Deepu, Chacko John; Heng, Chun-Huat; Lian, Yong

2017-04-01

This paper presents a novel data compression and transmission scheme for power reduction in Internet-of-Things (IoT) enabled wireless sensors. In the proposed scheme, data is compressed with both lossy and lossless techniques, so as to enable hybrid transmission mode, support adaptive data rate selection and save power in wireless transmission. Applying the method to electrocardiogram (ECG), the data is first compressed using a lossy compression technique with a high compression ratio (CR). The residual error between the original data and the decompressed lossy data is preserved using entropy coding, enabling a lossless restoration of the original data when required. Average CR of 2.1 × and 7.8 × were achieved for lossless and lossy compression respectively with MIT/BIH database. The power reduction is demonstrated using a Bluetooth transceiver and is found to be reduced to 18% for lossy and 53% for lossless transmission respectively. Options for hybrid transmission mode, adaptive rate selection and system level power reduction make the proposed scheme attractive for IoT wireless sensors in healthcare applications.

Evaluation of the Prevention and Reactivation Care Program (PReCaP for the hospitalized elderly: a prospective nonrandomized controlled trial

Directory of Open Access Journals (Sweden)

Asmus-Szepesi KJ

2015-03-01

Full Text Available Kirsten J Asmus-Szepesi,1 Linda E Flinterman,1 Marc A Koopmanschap,2 Anna P Nieboer,2 Ton J Bakker,3 Johan P Mackenbach,1 Ewout W Steyerberg1 1Department of Public Health, Erasmus University Medical Center, 2Institute of Health Policy and Management, Erasmus University, 3Stichting Wetenschap Balans, Rotterdam, the Netherlands Background: The hospitalized elderly are at risk of functional decline. We evaluated the effects and care costs of a specialized geriatric rehabilitation program aimed at preventing functional decline among at-risk hospitalized elderly.Methods: The prospective nonrandomized controlled trial reported here was performed in three hospitals in the Netherlands. One hospital implemented the Prevention and Reactivation Care Program (PReCaP, while two other hospitals providing usual care served as control settings. Within the PReCaP hospital we compared patients pre-implementation with patients post-implementation of the PReCaP (“within-hospital analysis”, while our nonrandomized controlled trial compared patients of the PReCaP hospital post-implementation with patients from the two control hospitals providing usual care (“between-hospital analysis”. Hospitalized patients 65 years or older and at risk of functional decline were interviewed at baseline and at 3 and 12 months using validated questionnaires to score functioning, depression, and health-related quality of life (HRQoL. We estimated costs per unit of care from hospital information systems and national data sources. We used adjusted general linear mixed models to analyze functioning and HRQoL.Results: Between-hospital analysis showed no difference in activities of daily living (ADL or instrumental activities of daily living (IADL between PReCaP patients and control groups. PReCaP patients did have slightly better cognitive functioning (Mini Mental State Examination; 0.4 [95% confidence interval (CI 0.2–0.6], lower depression (Geriatric Depression Scale 15; -0

Hierarchical control of a photovoltaic/battery based DC microgrid including electric vehicle wireless charging station

DEFF Research Database (Denmark)

Xiao, Zhao xia; Fan, Haodong; Guerrero, Josep M.

2017-01-01

In this paper, the hierarchical control strategy of a photovoltaic/battery based dc microgrid is presented for electric vehicle (EV) wireless charging. Considering irradiance variations, battery charging/discharging requirements, wireless power transmission characteristics, and onboard battery...... coils, receiving coils and compensation capacitors, the wireless power transmission system is designed to be resonant when it is operating at the rated power, with the aim to achieve the optimum transmission system efficiency. Simulation and experimental results of the hierarchical control...... charging power change and other factors, the possible operation states are obtained. A hierarchical control strategy is established, which includes central and local controllers. The central controller is responsible for the selection and transfer of operation states and the management of the local...

Wireless physical layer security

Science.gov (United States)

Poor, H. Vincent; Schaefer, Rafael F.

2017-01-01

Security in wireless networks has traditionally been considered to be an issue to be addressed separately from the physical radio transmission aspects of wireless systems. However, with the emergence of new networking architectures that are not amenable to traditional methods of secure communication such as data encryption, there has been an increase in interest in the potential of the physical properties of the radio channel itself to provide communications security. Information theory provides a natural framework for the study of this issue, and there has been considerable recent research devoted to using this framework to develop a greater understanding of the fundamental ability of the so-called physical layer to provide security in wireless networks. Moreover, this approach is also suggestive in many cases of coding techniques that can approach fundamental limits in practice and of techniques for other security tasks such as authentication. This paper provides an overview of these developments.

Implementing 802.11 with microcontrollers wireless networking for embedded systems designers

CERN Document Server

Eady, Fred

2005-01-01

Wireless networking is poised to have a massive impact on communications, and the 802.11 standard is to wireless networking what Ethernet is to wired networking. There are already over 50 million devices using the dominant IEEE 802.11 (essentially wireless Ethernet) standard, with astronomical growth predicted over the next 10 years. New applications are emerging every day, with wireless capability being embedded in everything from electric meters to hospital patient tracking systems to security devices. This practical reference guides readers through the wireless technology forest, gi

Wireless Physical Layer Security with CSIT Uncertainty

KAUST Repository

Hyadi, Amal

2017-09-01

Recent years have been marked by an enormous growth of wireless communication networks and an extensive use of wireless applications. In return, this phenomenal expansion induced more concerns about the privacy and the security of the users. Physical layer security is one of the most promising solutions that were proposed to enhance the security of next generation wireless systems. The fundamental idea behind this technique is to exploit the randomness and the fluctuations of the wireless channel to achieve security without conditional assumptions on the computational capabilities of the eavesdropper. In fact, while these elements have traditionally been associated with signal deterioration, physical layer security uses them to ensure the confidentiality of the users. Nevertheless, these technical virtues rely heavily on perhaps idealistic channel state information assumptions. In that regard, the aim of this thesis is to look at the physical layer security paradigm from the channel uncertainty perspective. In particular, we discuss the ergodic secrecy capacity of different wiretap channels when the transmitter is hampered by the imperfect knowledge of the channel state information (CSI). We consider two prevalent causes of uncertainty for the CSI at transmitter (CSIT); either an error of estimation occurs at the transmitter and he can only base his coding and the transmission strategies on a noisy version of the CSI, or the CSI feedback link has a limited capacity and the legitimate receivers can only inform the transmitter about the quantized CSI. We investigate both the single-user multiple-input multiple-output (MIMO) wiretap channel and the multi-user broadcast wiretap channel. In the latter scenario, we distinguish between two situations: multiple messages transmission and common message transmission. We also discuss the broadcast channel with confidential messages (BCCM) where the transmitter has one common message to be transmitted to two users and one

Evaluation of a Novel Wireless Transmission System for Trauma Ultrasound Examinations From Moving Ambulances.

Science.gov (United States)

Morchel, Herman; Ogedegbe, Chinwe; Chaplin, William; Cheney, Brianna; Zakharchenko, Svetlana; Misch, David; Schwartz, Matthew; Feldman, Joseph; Kaul, Sanjeev

2018-03-01

To determine if physicians trained in ultrasound interpretation perceive a difference in image quality and usefulness between Extended Focused Assessment with Sonography ultrasound examinations performed at bedside in a hospital vs. by emergency medical technicians minimally trained in medical ultrasound on a moving ambulance and transmitted to the hospital via a novel wireless system. In particular, we sought to demonstrate that useful images could be obtained from patients in less than optimal imaging conditions; that is, while they were in transport. Emergency medical technicians performed the examinations during transport of blunt trauma patients. Upon patient arrival at the hospital, a bedside Extended Focused Assessment with Sonography examination was performed by a physician. Both examinations were recorded and later reviewed by physicians trained in ultrasound interpretation. Data were collected on 20 blunt trauma patients over a period of 13 mo. Twenty ultrasound-trained physicians blindly compared transmitted vs. bedside images using 11 Questionnaire for User Interaction Satisfaction scales. Four paired samples t-tests were conducted to assess mean differences between ratings for ambulatory and base images. Although there is a slight tendency for the average rating across all subjects and raters to be slightly higher in the base than in the ambulatory condition, none of these differences are statistically significant. These results suggest that the quality of the ambulatory images was viewed as essentially as good as the quality of the base images.

Transmission techniques for 4G systems

CERN Document Server

Da Silva, Mario Marques

2012-01-01

Fourth Generation (4G) wireless communication systems support current and emergent multimedia services such as mobile TV, social networks and gaming, high-definition TV, video teleconferencing, and messaging services. These systems feature the All-over-IP concept and boast improved quality of service. Several important R&D activities are currently under way in the field of wireless communications for 4G systems, but the coverage is widespread in the literature. Transmission Techniques for 4G Systems presents a compilation of the latest developments in the field of wireless communications for 4

BLUETOOTH WIRELESS TECHNOLOGY: A MILESTONE IN ICT

African Journals Online (AJOL)

DJFLEX

This article summarizes the Bluetooth technology – a type of Wireless Personal Area Network (WPAN) with emphasis ... facilitating data transmission over short distances from fixed and ... primarily designed for low power consumption, with a.

Knowledge-Based Multiple Access Protocol in Broadband Wireless ATM Networks

DEFF Research Database (Denmark)

Liu, Hong; Gliese, Ulrik Bo; Dittmann, Lars

1999-01-01

In this paper, we propose a knowledge-based multiple access protocol for the extension of wireline ATM to wireless networks. The objective is to enable effecient transmission of all kinds of ATM traffic in the wireless channel with guaranteed QoS.The proposed protocol utilixes knowledge of the main...... guaranteed QoS requirements to a variety of ATM applications....

Silicon Photonics Integrated Circuits for 5th Generation mm-Wave Wireless Communications

DEFF Research Database (Denmark)

Rommel, Simon; Vegas Olmos, Juan José; Tafur Monroy, Idelfonso

Hybrid photonic-wireless transmission schemes in the mm-wave frequency are promising candidates to enable the multi-gigabit per second data communications required from wireless and mobile networks of the 5th and future generations. Photonic integration may pave the way to practical applicability...

Time and Energy Efficient Relay Transmission for Multi-Hop Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Jin-Woo Kim

2016-06-01

Full Text Available The IEEE 802.15.4 standard is widely recognized as one of the most successful enabling technologies for short range low rate wireless communications and it is used in IoT applications. It covers all the details related to the MAC and PHY layers of the IoT protocol stack. Due to the nature of IoT, the wireless sensor networks are autonomously self-organized networks without infrastructure support. One of the issues in IoT is the network scalability. To address this issue, it is necessary to support the multi-hop topology. The IEEE 802.15.4 network can support a star, peer-to-peer, or cluster-tree topology. One of the IEEE 802.15.4 topologies suited for the high predictability of performance guarantees and energy efficient behavior is a cluster-tree topology where sensor nodes can switch off their transceivers and go into a sleep state to save energy. However, the IEEE 802.15.4 cluster-tree topology may not be able to provide sufficient bandwidth for the increased traffic load and the additional information may not be delivered successfully. The common drawback of the existing approaches is that they do not address the poor bandwidth utilization problem in IEEE 802.15.4 cluster-tree networks, so it is difficult to increase the network performance. Therefore, to solve this problem in this paper we study a relay transmission protocol based on the standard protocol in the IEEE 802.15.4 MAC. In the proposed scheme, the coordinators can relay data frames to their parent devices or their children devices without contention and can provide bandwidth for the increased traffic load or the number of devices. We also evaluate the performance of the proposed scheme through simulation. The simulation results demonstrate that the proposed scheme can improve the reliability, the end-to-end delay, and the energy consumption.

Reliable Uplink Communication through Double Association in Wireless Heterogeneous Networks

DEFF Research Database (Denmark)

Kim, Dong Min; Popovski, Petar

2016-01-01

We investigate methods for network association that improve the reliability of uplink transmissions in dense wireless heterogeneous networks. The stochastic geometry analysis shows that the double association, in which an uplink transmission is transmitted to a macro Base Station (BS) and small BS...

Coordination of Regenerative Relays and Direct Users in Wireless Cellular Networks

DEFF Research Database (Denmark)

Thai, Chan; Popovski, Petar

2011-01-01

The area of wireless cooperation/relaying has recently been significantly enriched by the ideas of wireless network coding (NC), which bring substantial gains in spectral efficiency. These gains have mainly been demonstrated in scenarios with two-way relaying. Inspired by the ideas of wireless NC......, recently we have proposed techniques for coordinated direct/relay (CDR) transmissions. These techniques embrace the interference among the communication flows to/from direct and relayed users, leveraging on the fact that the interference can be subsequently canceled. Hence, by allowing simultaneous...... transmissions, spectral efficiency is increased. In our prior work, we have considered CDR with non-regenerative relay that uses Amplify-and-Forward (AF). In this paper we consider the case of regenerative Decode-and-Forward (DF) relay. This refers also to joint decoding of the interfering flows received over...

Wireless communications networks for the smart grid

CERN Document Server

Ho, Quang-Dung; Rajalingham, Gowdemy; Le-Ngoc, Tho

2014-01-01

This brief presents a comprehensive review of the network architecture and communication technologies of the smart grid communication network (SGCN). It then studies the strengths, weaknesses and applications of two promising wireless mesh routing protocols that could be used to implement the SGCN. Packet transmission reliability, latency and robustness of these two protocols are evaluated and compared by simulations in various practical SGCN scenarios. Finally, technical challenges and open research opportunities of the SGCN are addressed. Wireless Communications Networks for Smart Grid provi

Network Coding Opportunities for Wireless Grids Formed by Mobile Devices

DEFF Research Database (Denmark)

Nielsen, Karsten Fyhn; Madsen, Tatiana Kozlova; Fitzek, Frank

2008-01-01

Wireless grids have potential in sharing communication, computational and storage resources making these networks more powerful, more robust, and less cost intensive. However, to enjoy the benefits of cooperative resource sharing, a number of issues should be addressed and the cost of the wireless...... link should be taken into account. We focus on the question how nodes can efficiently communicate and distribute data in a wireless grid. We show the potential of a network coding approach when nodes have the possibility to combine packets thus increasing the amount of information per transmission. Our...... implementation demonstrates the feasibility of network coding for wireless grids formed by mobile devices....

Compatibility Issues of IPSec and TCP in Wireless Networks

Institute of Scientific and Technical Information of China (English)

ZHAO Hai-yang; XIN Yang

2004-01-01

Due to the problems arising when the Transmission Control Protocol (TCP) is applied over wireless networks, many TCP performance enhancement mechanisms have been proposed. However, such mechanisms aren't compatible with IPSec protocol. The paper reviews the TCP performance enhancement mechanisms in wireless networks. Then the conflicts between them are analyzed. Several proposals for solving theconflicts are discussed, and their benefit and limitations are examined.

Implementation of prevention of mother-to-child transmission of HIV programme through private hospitals of Delhi--policy implications.

Science.gov (United States)

Gupta, A K; Garg, C R; Joshi, B C; Rawat, N; Dabla, V; Gupta, A

2015-01-01

In India, programme for prevention of mother-to-child transmission (PMTCT) of HIV is primarily implemented through public health system. State AIDS Control Societies (SACSs) encourage private hospitals to set up integrated counselling and testing centres (ICTCs). However, private hospitals of Delhi did not set up ICTCs. Consequently, there is no information on PMTCT interventions in private hospitals of Delhi. This study was undertaken by Delhi SACS during March 2013 through September 2013 to assess status of implementation of PMTCT programme in various private hospitals of Delhi to assist programme managers in framing national policy to facilitate uniform implementation of National PMTCT guidelines. Out of total 575 private hospitals registered with Government of Delhi, 336 (58.4%) catering to pregnant women were identified. About 100 private hospitals with facility of antenatal care, vaginal/caesarean delivery and postnatal care and minimum 10 indoor beds were selected for study. Study sample comprised of large corporate hospitals (≥100 beds; n = 29), medium-sized hospitals (25 to women tested, 52 (0.14%) were detected HIV-positive. However, against National Policy, HIV testing was done without pre/post-test counselling/or consent of women, no PMTCT protocol existed, delivery of HIV-positive women was not undertaken and no efforts were made to link HIV-positive women to antiretroviral treatment. Major intervention observed was medical termination of pregnancy, which indicates lack of awareness in private hospitals about available interventions under national programme. The role of private hospitals in management of HIV in pregnant women must be recognized and mainstreamed in HIV control efforts. There is an urgent need for capacity building of private health care providers to improve standards of practice. National AIDS Control Organization may consider establishing linkages or adopting model developed by some countries with generalized epidemic for delivering