Dehydration of hydrated low-temperature tar

Energy Technology Data Exchange (ETDEWEB)

Yoshida, T

1949-01-01

Yoshida examined the mechanism of the dehydration of hydrated low-temperature tar with a microscope. The tar containing free carbon and coal dust is so stable that the removal of the above substances and water by a physical method is very difficult. Addition of light oil produced by fractionation of low-temperature tar facilitates the operations. Yoshida tried using the separate acid, neutral, and basic components of the light oil; the acid oil proved to be most effective. For many reasons it is convenient to use light oil as it is. In this method the quantity of light oil required is 2 to 3 times that of tar. But in supplementing the centrifugal method, the quantity of light oil needed might be only half the amount of tar.

Separating cresote from tars, mineral oils, etc

Energy Technology Data Exchange (ETDEWEB)

Erdmann, E

1921-01-07

Phenolic bodies are extracted from tars such as lignite, shale, peat, coal, producer and low temperature tars, and from tar distillates and residues and from mineral oils and distillates by washing with a mixture of acetone and water. Acetone extracts of the tars etc., may be mixed with water or aqueous acetone to cause the separation of the oils, while the creosote remains in solution.

Bioremediation potential of coal-tar-oil-contaminated soil

International Nuclear Information System (INIS)

Lajoie, C.A.

1991-01-01

The bioremediation of coal tar oil contaminated soil was investigated in 90 day laboratory simulation experiments. The effect of soil moisture, humic acid amendment, and coal tar oil concentration on the rate of disappearance of individual coal tar oil constituents (PAHs and related compounds) was determined by methylene chloride extraction and gas chromatography. Mass balance experiments determined the fate of both the individual 14 C-labeled PAHs phenanthrene, pyrene, and benzo(a)pyrene, and the total coal tar oil carbon. Mineralization, volatilization, incorporation into microbial biomass, disappearance of individual coal tar oil constitutents, and the distribution of residual 14 C-activity in different soil fractions were measured. The rate of disappearance of coal tar oil constituents increased with increasing soil moisture over the experimental range. Humic acid amendment initially enhanced the rate of disappearance, but decreased the extent of disappearance. The amount of contamination removed decreased at higher coal tar oil concentrations. The practical limit for biodegradation in the system tested appeared to be between 1.0 and 2.5% coal tar oil. Mineralization accounted for 40 to 50% of the applied coal tar oil. Volatilization was a minor pathway of disappearance

In situ recovery of oil from Utah tar sand: a summary of tar sand research at the Laramie Energy Technology Center

Energy Technology Data Exchange (ETDEWEB)

Marchant, L.C.; Westhoff, J.D.

1985-10-01

This report describes work done by the United States Department of Energy's Laramie Energy Technology Center from 1971 through 1982 to develop technology for future recovery of oil from US tar sands. Work was concentrated on major US tar sand deposits that are found in Utah. Major objectives of the program were as follows: determine the feasibility of in situ recovery methods applied to tar sand deposits; and establish a system for classifying tar sand deposits relative to those characteristics that would affect the design and operation of various in situ recovery processes. Contents of this report include: (1) characterization of Utah tar sand; (2) laboratory extraction studies relative to Utah tar sand in situ methods; (3) geological site evaluation; (4) environmental assessments and water availability; (5) reverse combustion field experiment, TS-1C; (6) a reverse combustion followed by forward combustion field experiment, TS-2C; (7) tar sand permeability enhancement studies; (8) two-well steam injection experiment; (9) in situ steam-flood experiment, TS-1S; (10) design of a tar sand field experiment for air-stream co-injection, TS-4; (11) wastewater treatment and oil analyses; (12) economic evaluation of an in situ tar sand recovery process; and (13) appendix I (extraction studies involving Utah tar sands, surface methods). 70 figs., 68 tabs.

Centrifuge treatment of coal tar

Energy Technology Data Exchange (ETDEWEB)

L.A. Kazak; V.Z. Kaidalov; L.F. Syrova; O.S. Miroshnichenko; A.S. Minakov [Giprokoks, the State Institute for the Design of Coke-Industry Enterprises, Kharkov (Ukraine)

2009-07-15

New technology is required for the removal of water and heavy fractions from regular coal tar. Centrifuges offer the best option. Purification of coal tar by means of centrifuges at OAO NLMK permits the production of pitch coke or electrode pitch that complies with current standards.

Coal tar pitch. Interrelations between properties and utilization of coal tar pitch

Energy Technology Data Exchange (ETDEWEB)

Collin, G; Koehler, H [Ruetgerswerke A.G., Duisburg (Germany, F.R.)

1977-06-01

Coal tar pitch is won as a highly aromatic, thermoplastic residue by destillating coal tar. In this paper the structure as well as the chemical and physical data of this pitch are introduced. In addition to this the actual as well as possible applications are indicated. For example, the pitch can be used for the production of binders, e.g. for electrodes and road construction as well as in combination with plastics for the production of insulating material and corrosion protection material.

Coal tar: past, present and future

Energy Technology Data Exchange (ETDEWEB)

Thami, G.P.; Sarkar, R. [Government Medical College & Hospital, Chandigarh (India). Dept. of Dermatology & Venerology

2002-03-01

Crude coal tar has been used in the treatment of dermatoses for many decades. In the last few years its use has been limited to skin diseases such as psoriasis and chronic dermatitis. Newer topical modalities for psoriasis are being used increasingly for treatment, but have failed to replace crude coal tar as a first-line treatment of psoriasis. The authors review the pharmacology, chemistry and use of crude coal tar in order to reappraise its role as a therapeutic agent in dermatology.

Distillation of tar and tar fractions in the presence of surface-active coke

Energy Technology Data Exchange (ETDEWEB)

Jaeppelt, A; Klaus, J

1943-01-01

The tar obtained by low-temperature carbonization of Upper Silesian gas coke and fractions from this tar were distilled in the presence of different grades of coke dust with varying surface activity; the coke had been activated by steam in the course of its production by low-temperature carbonization. The surface activity of the coke dusts was measured by determining the heat of wetting with C/sub 6/H/sub 6/. Tar and coke dust, both anhydrous, were mixed in a kneading machine in such proportions that the capillaries of the dust were saturated and enough ''externally'' bound tar was present to permit briquetting. The briquets were distilled without cracking and with steam as heating medium. The yield and quality of the distillate depended on the magnitude of the internal surface of the coke dust used; a mixture of a very active coke from brown coal and tar yielded a distillate with Conradson carbon residue of 1.34 percent, asphalt content 6.1 percent and eta/sub 20/ 5.4/sup 0/ E. as compared with C residue of 10.95 percent, asphalt content 33.5 percent and eta/sub 20/ 123.6/sup 0/ E. of the distillate obtained in the absence of surface-active coke. Even higher-boiling fractions can be improved by this treatment, although it is preferable to use oils with an initial boiling point below 300/sup 0/. The ratio of oil to adsorbent is not critical, but better results were obtained with higher percentages of added coke dust. The process in its present form is not suited for the conversion of crude creosote to useful phenols.

Flash hydropyrolysis of bituminous coal . III. Research on flash hydropyrolysis tar

Energy Technology Data Exchange (ETDEWEB)

Dong, M.; Zhu, Z.; He, Y.; Ding, N.; Tang, L. [East China University of Science and Technology, Shanghai (China)

2000-02-01

Tar sample obtained by flash hydropyrolysis (FHP) from Dongshen coal at high pressure entrained reactor was investigated. An effect of flash hydropyrolysis temperature on the main components in tar was studied and the quality of the tar was compared with high temperature coke oven tar. The results showed that: the yields of liquid hydrocarbon in FHP tar were more than 15%, which is twofold of that in coke oven tar; the FHP tar has high oil fraction and low pitch; high phenol components and pure condensed polycyclic aromatic hydrocarbon, and low aliphatic hydrocarbon. The components of the FHP tar were simpler than that of high temperature coke oven tar. Therefore, FHP has improved the quantity and quality of tar. 11 refs., 3 figs., 5 tabs.

Physical and performance properties of coal tar urethanes - pipe

International Nuclear Information System (INIS)

Hickney, J.; Hendry, M.

1984-01-01

The purpose of this paper is to review certain physical properties of coal tar extended urethane coatings designed specifically for use in the pipe coatings market. The blend of coal tar and urethane resins provides a novel finished product with properties cumulatively inherent in its constituents. Typically, coal tar and coal tar pitch offer exceptional water resistance and cathodic alkali resistance when blended with other resins. An example is the standard coal tar epoxies used for many years in the marine markets for shipbottoms

Characterization of acid tar waste from benzol purification | Danha ...

African Journals Online (AJOL)

The use of concentrated sulphuric acid to purify benzene, toluene and xylene produces acidic waste known as acid tar. The characterization of the acid tar to determine the composition and physical properties to device a way to use the waste was done. There were three acid tars two from benzene (B acid tar), toluene and ...

The temporal relationship between advertising and sales of low-tar cigarettes.

Science.gov (United States)

Reed, Mark B; Anderson, Christy M; Burns, David M

2006-12-01

To determine whether a temporal relationship exists between the advertising and sales of low-tar cigarettes. It was hypothesised that increases in the advertising of low-tar cigarettes would precede increases in sales for these cigarettes. The themes of cigarette advertisements were reviewed and coded for 20 low-tar cigarette brands advertised in 13 widely read magazines in the US between 1960 and 1996. These 20 brands represented most of the low-tar cigarette advertisements and cigarette sales from 1967 to 1996. Cigarette sales data were obtained from the 1994 Maxwell report that summarises all cigarette sales from 1925 to 1990. If the advertisement referred to the low-tar attributes of the cigarette advertised, the advertisement was coded as having a low-tar theme and was included in the analysis. Five different graphical presentations of the relationship between the advertising and sales of the 20 low-tar cigarette brands showed a temporal relationship between low-tar advertising and sales for these brands. This relationship was observed for brands that introduced a low-tar alternative into an existing brand family (eg, Marlboro Light) and for new exclusively low-tar brands (eg, Carlton). Despite large increases in the advertising for the exclusively low-tar brands, sales of these brands remained low relative to sales of the low-tar alternative brands. Increases in print advertising of 20 of the most popular low-tar cigarette brands were followed by increases in sales for these cigarettes. Despite increases in the advertising of exclusively low-tar brands in the mid-1970s and early 1980s, the sales of these brands never matched the sales of the low-tar alternative brands. This suggests that it may have been easier to get smokers to switch to low-tar brands within a brand family compared with entirely new low-tar brands. Over the past 30 years, the marketing of low-tar cigarettes as a healthier alternative to higher-tar cigarettes has resulted in these brands

Cancer fear over coal tar products

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-01-01

Discusses a report by Dutch researchers which suggests that the regular use of coal tar shampoos may significantly increase the risk of cancer due to the high levels of polynuclear aromatic hydrocarbons (PAHs) in the products. The PAH exposure of volunteers using a coal tar anti-dandruff shampoo was studied by measuring the amount of hydroxypyrene, a PAH breakdown product in their urine. Volunteers who had used the shampoo excreted high levels of hydroxypyrene the day after exposure. Excretion by the control group using a non-coal tar anti-dandruff shampoo remained constant. 1 ref., 1 fig.

The temporal relationship between advertising and sales of low‐tar cigarettes

Science.gov (United States)

Reed, Mark B; Anderson, Christy M; Burns, David M

2006-01-01

Objective and hypothesis To determine whether a temporal relationship exists between the advertising and sales of low‐tar cigarettes. It was hypothesised that increases in the advertising of low‐tar cigarettes would precede increases in sales for these cigarettes. Methods The themes of cigarette advertisements were reviewed and coded for 20 low‐tar cigarette brands advertised in 13 widely read magazines in the US between 1960 and 1996. These 20 brands represented most of the low‐tar cigarette advertisements and cigarette sales from 1967 to 1996. Cigarette sales data were obtained from the 1994 Maxwell report that summarises all cigarette sales from 1925 to 1990. If the advertisement referred to the low‐tar attributes of the cigarette advertised, the advertisement was coded as having a low‐tar theme and was included in the analysis. Results Five different graphical presentations of the relationship between the advertising and sales of the 20 low‐tar cigarette brands showed a temporal relationship between low‐tar advertising and sales for these brands. This relationship was observed for brands that introduced a low‐tar alternative into an existing brand family (eg, Marlboro Light) and for new exclusively low‐tar brands (eg, Carlton). Despite large increases in the advertising for the exclusively low‐tar brands, sales of these brands remained low relative to sales of the low‐tar alternative brands. Conclusions Increases in print advertising of 20 of the most popular low‐tar cigarette brands were followed by increases in sales for these cigarettes. Despite increases in the advertising of exclusively low‐tar brands in the mid‐1970s and early 1980s, the sales of these brands never matched the sales of the low‐tar alternative brands. This suggests that it may have been easier to get smokers to switch to low‐tar brands within a brand family compared with entirely new low‐tar brands. Over the past 30 years, the marketing of low‐tar

Structure and Mechanism of Staphylococcus aureus TarS, the Wall Teichoic Acid β-glycosyltransferase Involved in Methicillin Resistance.

Directory of Open Access Journals (Sweden)

Solmaz Sobhanifar

2016-12-01

Full Text Available In recent years, there has been a growing interest in teichoic acids as targets for antibiotic drug design against major clinical pathogens such as Staphylococcus aureus, reflecting the disquieting increase in antibiotic resistance and the historical success of bacterial cell wall components as drug targets. It is now becoming clear that β-O-GlcNAcylation of S. aureus wall teichoic acids plays a major role in both pathogenicity and antibiotic resistance. Here we present the first structure of S. aureus TarS, the enzyme responsible for polyribitol phosphate β-O-GlcNAcylation. Using a divide and conquer strategy, we obtained crystal structures of various TarS constructs, mapping high resolution overlapping N-terminal and C-terminal structures onto a lower resolution full-length structure that resulted in a high resolution view of the entire enzyme. Using the N-terminal structure that encapsulates the catalytic domain, we furthermore captured several snapshots of TarS, including the native structure, the UDP-GlcNAc donor complex, and the UDP product complex. These structures along with structure-guided mutants allowed us to elucidate various catalytic features and identify key active site residues and catalytic loop rearrangements that provide a valuable platform for anti-MRSA drug design. We furthermore observed for the first time the presence of a trimerization domain composed of stacked carbohydrate binding modules, commonly observed in starch active enzymes, but adapted here for a poly sugar-phosphate glycosyltransferase.

Characterization of Tar Deposits, Extraction and Sorption Properties

Directory of Open Access Journals (Sweden)

Pryszcz Adrian

2016-06-01

Full Text Available The main goal of this paper was to characterize and find a useful solution for the decomposition of tar deposits. For the experimental part, tar deposits, formed by polymerization and condensation reactions, were chosen from a storage tank for tars. At first the initial analyses of tar deposits (elemental, thermogravimetric, and calorimetric analyses were performed. After the characterization, the tar deposits were extracted in the Soxhlet extractor by acetone, toluene, and quinolone and activated with potassium hydroxide. As the final step of this work, the sorption characterization on the 3Flex Surface Characterization Analyzer (Micromeritics was performed. The specific surface area of the samples was evaluated using two methods - a single point measurement at p/p0=0.2 and BET method. Micropore and external surface areas were calculated based on a t-plot analysis (carbon black model.

Preparation of pure phenols from tars

Energy Technology Data Exchange (ETDEWEB)

Meyer, J

1929-06-18

A process is disclosed for preparing pure phenols from brown coal and shale tar, characterized in that the alkaline extract obtained from the tar is oxidized and concurrently the alkaline solution is separated from the existing impurities by heating with steam at high temperature, which finally reaches at least 150/sup 0/C.

New method for the exact determination of phenols in low-temperature tar and tar oils

Energy Technology Data Exchange (ETDEWEB)

Lambris, G; Haferkorn, H

1949-01-01

A 3-gram sample of water-free tar or tar oil containing approximately 50% phenols is dissolved in a mixture of benzene and xylene and a known excess of a 20% KOH solution of known normality saturated with benzene and xylene is added. Weight of the KOH is determined by difference. This mixture is shaken repeatedly in a 300-milliliter separatory funnel. After standing for 0.5 h, the dark or almost black phenolate solution containing the major portion is separated and weighed. Care must be taken to prevent the induction of solids. The phenolate in the residue is extracted with hot water and titrated with 0.2N HCl and 1 ml. Congo red (1:100). If water is present in the tar or tar oil, 100 ml of xylene is added immediately after weighing and the water separated by distillation the weight of which must be determined. Any phenols carried over are dissolved in the small quantity of xylene in the distillate. This quantity is added to the bulk of the xylene. After any remaining phenols are extracted from the tar residue with boiling benzene, the benzene-xylene mixture is treated with KOH as above. The accuracy of the method is estimated to be +-1% as shown by experiments with phenol; o-, m-, and p-cresol; cresol mixture; and pyrocatechol. The weight of the dissolved phenols X is determined by X = c - a + cd/(ab - d) where a = weight of KOH, b = HCl used per gram of KOH, C = weight of major portion of phenolate solution, which is formed by shaking the phenol solution with KOH, d = HCl used for titration of phenolate residue.

Infrared absorption characteristics of hydroxyl groups in coal tars

Energy Technology Data Exchange (ETDEWEB)

Cannon, S A; Chu, C J; Hange, R H; Margrave, J L

1987-01-01

Tar evolution was observed over a temperature range of 150-600 C for four coals. Pittsburgh bituminous, Illinois No.6, Rawhide subbituminous, and Texas lignite. Isolation of the evolved tars in a nitrogen matrix at 15 degrees K produced better resolved infrared spectra than those in a coal matrix, thus enhancing structural characterization of the tar molecules. Two distinct hydroxyl functional groups in the tar molecules free of hydrogen bonding were identified for the first time without interference from H/sub 2/O absorptions. These absorptions at 3626.5 cm/sup -1/ have been assigned to phenolic hydroxyls. It is suggested that carboxylic and aliphatic hydroxyl groups do not survive the vaporization process. Tars from Illinois No.6 were found to contain the largest amount of phenolic hydroxyl; Pittsburgh No. 8 tar contains approximately half of that for Illinois No.6 while Rawhide and Texas lignite contain much less phenolic than either of the other coals. 10 references, 6 figures, 1 table.

Sunflower oil in the treatment of hot tar burns.

Science.gov (United States)

Türegün, M; Oztürk, S; Selmanpakoğlu, N

1997-08-01

Hot tar burns compose a unique class of thermal injury, because removal of this highly sticky compound may be very difficult without inflicting additional tissue damage. Early removal of tar facilitates assessment of the burn and improves patient comfort. Although the use of many substances for the painless removal of tar has been described, we used sunflower oil effectively in the treatment of four tar burn patients. This first report describes the practical and successful use of sunflower oil which was easily obtained from the hospital kitchen.

Tar dew point analyser as a tool in biomass gasification

Energy Technology Data Exchange (ETDEWEB)

Vreugdenhil, B.J.; Kuipers, J. [ECN Biomass, Coal and Environmental Research, Petten (Netherlands)

2008-08-15

Application of the Tar Dew point Analyzer (TDA) in different biomass based gasification systems and subsequent gas cleaning setups has been proven feasible. Such systems include BFB gasifiers, CFB gasifier and fixed bed gasifiers, with tar crackers or different scrubbers for tar removal. Tar dew points obtained with the TDA give direct insight in the performance of the gas cleaning section and help prevent any tar related problems due to condensation. The current TDA is capable of measuring tar dew points between -20 to 200C. This manuscript will present results from 4 different gasification setups. The range of measured tar dew points is -7 to 164C with comparable results from the calculated dew points based on the SPA measurements. Further detail will be presented on the differences between TDA and SPA results and explanations will be given for deviations that occurred. Improvements for the TDA regarding future work will be presented.

The catalytic cracking mechanism of lignite pyrolysis char on tar

International Nuclear Information System (INIS)

Lei, Z.; Huibin, H.; Xiangling, S.; Zhenhua, M.; Lei, Z.

2017-01-01

The influence of different pyrolysis conditions for tar catalytic cracking will be analyzed according to the lignite pyrolysis char as catalyst on pyrolytic tar in this paper. The pyrolysis char what is the by-product of the cracking of coal has an abundant of pore structure and it has good catalytic activity. On this basis, making the modified catalyst when the pyrolysis char is activation and loads Fe by impregnation method. The cracking mechanism of lignite pyrolytic tar is explored by applying gas chromatograph to analyze splitting products of tar. The experimental results showed that: (1) The effect of tar cracking as the pyrolysis temperature, the heating rate, the volatilization of pyrolysis char and particle size increasing is better and better. The effect of the catalytic and cracking of lignite pyrolysis char in tar is best when the heating rate, the pyrolysis temperature, the volatiles of pyrolysis char, particle size is in specific conditions.(2) The activation of pyrolysis char can improve the catalytic effect of pyrolysis char on the tar cracking. But it reduces the effect of the tar cracking when the pyrolysis char is activation loading Fe. (author)

Low-temperature tar and oil: properties and applications

Energy Technology Data Exchange (ETDEWEB)

Heinze, R

1942-01-01

In Germany the value of low-temperature tar is largely dependent on its fuel fractions; these vary with the coal and the method of carbonization (external heating or recirculated gases). Brown-coal tars can be processed by distillation, cracking under pressure, hydrogenation under pressure (largest volume of tar is processed by this method) and by solvent extraction, with EtOH, SO/sub 2/, or phenol. Each of these processes is discussed in detail. In the pressure-hydrogenation process, 1.25 kilogram of brown-coal tar yields approximately 1 kilogram of gasoline with an octane number of 60 to 70. Low-temperature tars from bituminous coals can be hydrogenated readily but are not well adapted to solvent extraction. Attempts should be made to produce tar approximating the desired characteristics for fuel directly from the carbonizing apparatus. For laboratory carbonization tests, an approximation to results secured by externally heated retorts is secured by using an insert consisting of a series of perforated trays in the 200-gram Fischer aluminum retort; this reduces the capacity to 100 gram. Fractional condensation is used to separate heavy oil, middle oil, and liquor; low-boiling products are condensed at -20/sup 0/ by solid CO/sub 2/.

Chemical-composition studies of low-temperature-carbonization coal tar

Energy Technology Data Exchange (ETDEWEB)

Edel' shtein, N G; Lanin, V A

1955-01-01

Pintsch-oven low-temperature tar was separated into its constituents by conventional methods, and the average of 2 results was neutral asphaltenes 12.56, basic asphaltenes 2.61, acid asphaltenes 18.82, phenols 13.23, bases 2.31, neutral oil 17.66, crystalline paraffins 7.34, silica-gel tars (I) (benzene extract) 15.40, I (acetone extract) 2.47, carbenes 0.45, and carbides and dust 1.44%. The low-temperature-tar asphaltenes and tars differ from shale-oil tars by being lower in C and higher in H, with a considerably higher C:H ratio. Their specific gravity is somewhat higher, and they are cyclic in structure. The asphaltenes and silica-gel tars of coal tar and shale oil were hydrogenated, molecular weights d/sub 4//sup 20/ and n/sub 4//sup 20/ of the separated compounds were determined, and empirical formulas of the hydrogenated compounds calculated. The neutral oil was separated into saturated, intermediate (iodine number 23), unsaturated (iodine number 51), a small quantity of a mixture of unsaturated and aromatic hydrocarbons, and 44.9% aromatic hydrocarbons. While naphthenes seem to be predominantly present in the neutral-oil fraction of shale oil, aromatic hydrocarbons are predominant in coal oil.

Process of transforming tars, etc

Energy Technology Data Exchange (ETDEWEB)

1929-04-11

A process is described for treating tars obtained by carbonization, at high or low temperature, of coals, lignites, shales, and other carbonaceous materials or fractions of these tars, for obtaining products of greater value, consisting of polymerizing or saturating the unstable hydrocarbons in the presence of catalyzers by the progressing action particularly of halogenated metals, such as titanium tetrachloride, iron chloride, etc. and applying a known process of recovery, the disclosed process leading to an important reduction of final losses.

Mineral oils, tars. [British patent

Energy Technology Data Exchange (ETDEWEB)

O' Brien, A M; Handmarch, E

1933-08-11

Hydrocarbon materials such as mineral oils and tars from coal, shale, lignite, or peat are freed from phenols and like oxy-bodies by heating under pressure in a closed vessel to a temperature and for a time sufficient to effect reduction of the oxy-bodies, and then removing the water formed by the reaction. 350/sup 0/ to 400/sup 0/C. for 30 to 60 minutes is suitable. Any wax-like constituents are converted to liquids of lower viscosity and settling point. The product may be fractionated to give light oils and a residue of aviation Diesel fuel. In an example, oil from the low-temperature distillation of coal and having a tar acid content of 30 per cent is treated in a tubular converter at 380/sup 0/C. and 400 lb. per sq. in for 40 min., and the benzine toluol, and xylol distilled; the residue has a tar acid content of only 7.6 per cent.

Reaction Mechanism of Tar Evolution in Biomass Steam Gasification for Hydrogen Production

International Nuclear Information System (INIS)

Shingo Katayama; Masahiro Suzuki; Atsushi Tsutsumi

2006-01-01

Reaction mechanism of tar evolution in steam gasification of biomass was investigated with a continuous cross-flow moving bed type differential reactor, in which tar and gases can be fractionated according to reaction time. We estimated that time profile of tar and gas evolution in the gasification of cellulose, xylan, and lignin, and compared it with experimental product time profile of real biomass gasification. The experimental tar evolution rate is different from estimated tar evolution rate. The estimated tar evolution rate has a peak at 20 s. On the other hand, the experimental tar evolution rate at 20 s is little, and tar at initial stage includes more water-soluble and water-insoluble compounds. It can be concluded that in the real biomass steam gasification the evolution of tar from cellulose and lignin component was found to be precipitated by that from hemi-cellulose component. (authors)

DECOMPOSITION OF TARS IN MICROWAVE PLASMA – PRELIMINARY RESULTS

Directory of Open Access Journals (Sweden)

Mateusz Wnukowski

2014-07-01

Full Text Available The paper refers to the main problem connected with biomass gasification - a presence of tar in a product gas. This paper presents preliminary results of tar decomposition in a microwave plasma reactor. It gives a basic insight into the construction and work of the plasma reactor. During the experiment, researches were carried out on toluene as a tar surrogate. As a carrier gas for toluene and as a plasma agent, nitrogen was used. Flow rates of the gases and the microwave generator’s power were constant during the whole experiment. Results of the experiment showed that the decomposition process of toluene was effective because the decomposition efficiency attained above 95%. The main products of tar decomposition were light hydrocarbons and soot. The article also gives plans for further research in a matter of tar removal from the product gas.

Recovery of very viscous lubricating oils from shale-tar, etc

Energy Technology Data Exchange (ETDEWEB)

Erdmann, E

1918-01-22

A process is disclosed for the recovery of very viscous lubricating oils from brown-coal tar and shale tar, consisting in driving off from the crude tar or the tar freed from volatile constituents after removal of paraffin by precipitation with a volatile solvent such as acetone or one of its homologs, the light oils more or less completely with superheated steam from about 200 to 250/sup 0/C without any outside heating over a free flame.

VAPOR PRESSURES AND HEATS OF VAPORIZATION OF PRIMARY COAL TARS

Energy Technology Data Exchange (ETDEWEB)

Eric M. Suuberg; Vahur Oja

1997-07-01

This project had as its main focus the determination of vapor pressures of coal pyrolysis tars. It involved performing measurements of these vapor pressures and from them, developing vapor pressure correlations suitable for use in advanced pyrolysis models (those models which explicitly account for mass transport limitations). This report is divided into five main chapters. Each chapter is a relatively stand-alone section. Chapter A reviews the general nature of coal tars and gives a summary of existing vapor pressure correlations for coal tars and model compounds. Chapter B summarizes the main experimental approaches for coal tar preparation and characterization which have been used throughout the project. Chapter C is concerned with the selection of the model compounds for coal pyrolysis tars and reviews the data available to us on the vapor pressures of high boiling point aromatic compounds. This chapter also deals with the question of identifying factors that govern the vapor pressures of coal tar model materials and their mixtures. Chapter D covers the vapor pressures and heats of vaporization of primary cellulose tars. Chapter E discusses the results of the main focus of this study. In summary, this work provides improved understanding of the volatility of coal and cellulose pyrolysis tars. It has resulted in new experimentally verified vapor pressure correlations for use in pyrolysis models. Further research on this topic should aim at developing general vapor pressure correlations for all coal tars, based on their molecular weight together with certain specific chemical characteristics i.e. hydroxyl group content.

Microstructure and properties of lignite tar and pitch. Part II

Energy Technology Data Exchange (ETDEWEB)

Walther, H

1954-01-01

Photomicrographs reveal the presence of crystalline wax which affects the working properties in lignite tars and pitch. The crystals are large needles after slow cooling and small after rapid cooling. The crystals are paraffinic in character. All samples were nonhomogeneous. Thus the properties of lignite tar and pitch are varied by the source of the lignite and history of the specimen, neither softening point nor dropping point seems to satisfactorily characterize these tars. The samples exhibit thixotropic behavior characteristic of a structural viscosity and show hysteresis loops on varying the working rate. The variations have hindered use of lignite tars and pitches except where solubility in a solvent such as coal tar oil can be used to advantage.

Catalytic destruction of tar in biomass derived producer gas

International Nuclear Information System (INIS)

Zhang Ruiqin; Brown, Robert C.; Suby, Andrew; Cummer, Keith

2004-01-01

The purpose of this study is to investigate catalytic destruction of tar formed during gasification of biomass, with the goal of improving the quality of the producer gas. This work focuses on nickel based catalysts treated with alkali in an effort to promote steam gasification of the coke that deposits on catalyst surfaces. A tar conversion system consisting of a guard bed and catalytic reactor was designed to treat the producer gas from an air blown, fluidized bed biomass gasifier. The guard bed used dolomite to crack the heavy tars. The catalytic reactor was used to evaluate three commercial steam reforming catalysts. These were the ICI46-1 catalyst from Imperial Chemical Industry and Z409 and RZ409 catalysts from Qilu Petrochemical Corp. in China. A 0.5-3 l/min slipstream from a 5 tpd biomass gasifier was used to test the tar conversion system. Gas and tar were sampled before and after the tar conversion system to evaluate the effectiveness of the system. Changes in gas composition as functions of catalytic bed temperature, space velocity and steam/TOC (total organic carbon) ratio are presented. Structural changes in the catalysts during the tests are also described

Characterization of acid tars

Energy Technology Data Exchange (ETDEWEB)

Leonard, Sunday A., E-mail: sunday.leonard@ucl.ac.uk [Department of Civil Environmental and Geomatic Engineering, University College London, Chadwick Building, Gower Street, London, WC1E 6BT (United Kingdom); Stegemann, Julia A. [Department of Civil Environmental and Geomatic Engineering, University College London, Chadwick Building, Gower Street, London, WC1E 6BT (United Kingdom); Roy, Amitava [J. Bennett Johnston, Sr., Centre for Advance Microstructures and Devices (CAMD), 6980 Jefferson Highway, Louisiana State University, Baton Rouge, LA, 70806 (United States)

2010-03-15

Acid tars from the processing of petroleum and petrochemicals using sulfuric acid were characterized by gas chromatography/mass spectrometry (GC/MS), inductively coupled plasma/optical emission spectrometry (ICP/OES), differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectrometry, and scanning electron microscopy/energy dispersive X-ray (SEM/EDX) micro-analysis. Leaching of contaminants from the acid tars in 48 h batch tests with distilled water at a liquid-to-solid ratio 10:1 was also studied. GC/MS results show that the samples contained aliphatic hydrocarbons, cyclic hydrocarbons, up to 12 of the 16 USEPA priority polycyclic aromatic hydrocarbons (PAHs), and numerous other organic groups, including organic acids (sulfonic acids, carboxylic acids and aromatic acids), phenyl, nitrile, amide, furans, thiophenes, pyrroles, and phthalates, many of which are toxic. Metals analysis shows that Pb was present in significant concentration. DSC results show different transition peaks in the studied samples, demonstrating their complexity and variability. FTIR analysis further confirmed the presence of the organic groups detected by GC/MS. The SEM/EDX micro-analysis results provided insight on the surface characteristics of the samples and show that contaminants distribution was heterogeneous. The results provide useful data on the composition, complexity, and variability of acid tars; information which hitherto have been scarce in public domain.

Characterization of acid tars

International Nuclear Information System (INIS)

Leonard, Sunday A.; Stegemann, Julia A.; Roy, Amitava

2010-01-01

Acid tars from the processing of petroleum and petrochemicals using sulfuric acid were characterized by gas chromatography/mass spectrometry (GC/MS), inductively coupled plasma/optical emission spectrometry (ICP/OES), differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectrometry, and scanning electron microscopy/energy dispersive X-ray (SEM/EDX) micro-analysis. Leaching of contaminants from the acid tars in 48 h batch tests with distilled water at a liquid-to-solid ratio 10:1 was also studied. GC/MS results show that the samples contained aliphatic hydrocarbons, cyclic hydrocarbons, up to 12 of the 16 USEPA priority polycyclic aromatic hydrocarbons (PAHs), and numerous other organic groups, including organic acids (sulfonic acids, carboxylic acids and aromatic acids), phenyl, nitrile, amide, furans, thiophenes, pyrroles, and phthalates, many of which are toxic. Metals analysis shows that Pb was present in significant concentration. DSC results show different transition peaks in the studied samples, demonstrating their complexity and variability. FTIR analysis further confirmed the presence of the organic groups detected by GC/MS. The SEM/EDX micro-analysis results provided insight on the surface characteristics of the samples and show that contaminants distribution was heterogeneous. The results provide useful data on the composition, complexity, and variability of acid tars; information which hitherto have been scarce in public domain.

Ultrasound assisted, thermally activated persulfate oxidation of coal tar DNAPLs.

Science.gov (United States)

Peng, Libin; Wang, Li; Hu, Xingting; Wu, Peihui; Wang, Xueqing; Huang, Chumei; Wang, Xiangyang; Deng, Dayi

2016-11-15

The feasibility of ultrasound assisted, thermally activated persulfate for effective oxidation of twenty 2-6 ringed coal tar PAHs in a biphasic tar/water system and a triphasic tar/soil/water system were investigated and established. The results indicate that ultrasonic assistance, persulfate and elevated reaction temperature are all required to achieve effective oxidation of coal tar PAHs, while the heating needed can be provided by ultrasonic induced heating as well. Further kinetic analysis reveals that the oxidation of individual PAH in the biphasic tar/water system follows the first-order kinetics, and individual PAH oxidation rate is primary determined by the mass transfer coefficients, tar/water interfacial areas, the aqueous solubility of individual PAH and its concentration in coal tar. Based on the kinetic analysis and experimental results, the contributions of ultrasound, persulfate and elevated reaction temperature to PAHs oxidation were characterized, and the effects of ultrasonic intensity and oxidant dosage on PAHs oxidation efficiency were investigated. In addition, the results indicate that individual PAH degradability is closely related to its reactivity as well, and the high reactivity of 4-6 ringed PAHs substantially improves their degradability. Copyright © 2016 Elsevier B.V. All rights reserved.

Análisis de cambio de régimen en series de tiempo no lienales utilizando modelos TAR

Directory of Open Access Journals (Sweden)

Hermilson Velásquez

2004-12-01

Full Text Available En muchas situaciones, la teoría recomienda un determinado modelo predictivo para una serie de tiempo financiera. Sin embargo, algunos comportamientos de estas series hacen que el modelo no sea apropiado. Una de las razones para ello puede ser la no linealidad de esos comportamientos. Se propone tratar estas series con modelos TAR (modelo autorregresivo por tramos; dichos modelos se definen por una variable umbral, por lo que en general resulta ser un modelo temporal no lineal. Un modelo de este tipo se formula como una serie temporal con su rezago como variable umbral, donde d es un entero positivo denominado retardo umbral. La variable umbral se desconoce en la práctica, y es importante saber cómo determinarla; en este artículo se explica cómo. Los modelos TAR se ilustran haciendo una modelación del PIB de España.

Análisis de cambio de régimen en series de tiempo no lineales utilizando modelos TAR

Directory of Open Access Journals (Sweden)

Fredy Pérez

2004-01-01

Full Text Available En muchas situaciones, la teoría recomienda un determinado modelo predictivo para una serie de tiempo financiera. Sin embargo, algunos comportamientos de estas series hacen que el modelo no sea apropiado. Una de las razones para ello puede ser la no linealidad de esos comportamientos. Se propone tratar estas series con modelos TAR (modelo autorregresivo por tramos; dichos modelos se definen por una variable umbral, por lo que en general resulta ser un modelo temporal no lineal. Un modelo de este tipo se formula como una serie temporal con su rezago como variable umbral, donde d es un entero positivo denominado retardo umbral. La variable umbral se desconoce en la práctica, y es importante saber cómo determinarla; en este artículo se explica cómo. Los modelos TAR se ilustran haciendo una modelación del PIB de España.

Application of organic geochemistry to coastal tar residues from central California

Energy Technology Data Exchange (ETDEWEB)

Kvenvolden, K.A.; Rosenbauer, R.J.; Hostettler, F.D.; Lorenson, T.D.

2000-01-01

Tar residues are common on the Monterey Bay National Marine Sanctuary. These coastal tar residues have been washed ashore and usually occur on headlands near the high-tide line. In this study, 18 coastal tar residues were collected and analyzed to determine their carbon isotopic compositions and values of selected biomarker ratios. All of the residues have very heavy ({sup 13}C-enriched) carbon isotopic compositions spanning a narrow range ({delta}{sup 13}C = {minus}22.2 to {minus}23.4{per{underscore}thousand}), and 28,30-bisnorhopane is present in all samples. These same geochemical characteristics are found in Monterey Formation oils from which the coastal tar residues were likely derived. These coastal residues could result from natural seeps or from accidental spills. Statistically the coastal tar residues can be organized into three groups, each of which may represent different spill or seep events. Seven samples of potential local representative sources for the tar residues were examined, but none could account for the coastal tars.

Study on tar generated from downdraft gasification of oil palm fronds.

Science.gov (United States)

Atnaw, Samson Mekbib; Kueh, Soo Chuan; Sulaiman, Shaharin Anwar

2014-01-01

One of the most challenging issues concerning the gasification of oil palm fronds (OPF) is the presence of tar and particulates formed during the process considering its high volatile matter content. In this study, a tar sampling train custom built based on standard tar sampling protocols was used to quantify the gravimetric concentration of tar (g/Nm3) in syngas produced from downdraft gasification of OPF. The amount of char, ash, and solid tar produced from the gasification process was measured in order to account for the mass and carbon conversion efficiency. Elemental analysis of the char and solid tar samples was done using ultimate analysis machine, while the relative concentration of the different compounds in the liquid tar was determined making use of a liquid gas chromatography (GC) unit. Average tar concentration of 4.928 g/Nm3 and 1.923 g/Nm3 was obtained for raw gas and cleaned gas samples, respectively. Tar concentration in the raw gas sample was found to be higher compared to results for other biomass materials, which could be attributed to the higher volatile matter percentage of OPF. Average cleaning efficiency of 61% which is comparable to that of sand bed filter and venturi scrubber cleaning systems reported in the literature was obtained for the cleaning system proposed in the current study.

Study on Tar Generated from Downdraft Gasification of Oil Palm Fronds

Directory of Open Access Journals (Sweden)

Samson Mekbib Atnaw

2014-01-01

Full Text Available One of the most challenging issues concerning the gasification of oil palm fronds (OPF is the presence of tar and particulates formed during the process considering its high volatile matter content. In this study, a tar sampling train custom built based on standard tar sampling protocols was used to quantify the gravimetric concentration of tar (g/Nm3 in syngas produced from downdraft gasification of OPF. The amount of char, ash, and solid tar produced from the gasification process was measured in order to account for the mass and carbon conversion efficiency. Elemental analysis of the char and solid tar samples was done using ultimate analysis machine, while the relative concentration of the different compounds in the liquid tar was determined making use of a liquid gas chromatography (GC unit. Average tar concentration of 4.928 g/Nm3 and 1.923 g/Nm3 was obtained for raw gas and cleaned gas samples, respectively. Tar concentration in the raw gas sample was found to be higher compared to results for other biomass materials, which could be attributed to the higher volatile matter percentage of OPF. Average cleaning efficiency of 61% which is comparable to that of sand bed filter and venturi scrubber cleaning systems reported in the literature was obtained for the cleaning system proposed in the current study.

Study on Tar Generated from Downdraft Gasification of Oil Palm Fronds

Science.gov (United States)

Atnaw, Samson Mekbib; Kueh, Soo Chuan; Sulaiman, Shaharin Anwar

2014-01-01

One of the most challenging issues concerning the gasification of oil palm fronds (OPF) is the presence of tar and particulates formed during the process considering its high volatile matter content. In this study, a tar sampling train custom built based on standard tar sampling protocols was used to quantify the gravimetric concentration of tar (g/Nm3) in syngas produced from downdraft gasification of OPF. The amount of char, ash, and solid tar produced from the gasification process was measured in order to account for the mass and carbon conversion efficiency. Elemental analysis of the char and solid tar samples was done using ultimate analysis machine, while the relative concentration of the different compounds in the liquid tar was determined making use of a liquid gas chromatography (GC) unit. Average tar concentration of 4.928 g/Nm3 and 1.923 g/Nm3 was obtained for raw gas and cleaned gas samples, respectively. Tar concentration in the raw gas sample was found to be higher compared to results for other biomass materials, which could be attributed to the higher volatile matter percentage of OPF. Average cleaning efficiency of 61% which is comparable to that of sand bed filter and venturi scrubber cleaning systems reported in the literature was obtained for the cleaning system proposed in the current study. PMID:24526899

Final Safety Assessment of Coal Tar as Used in Cosmetics

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-07-01

Coal Tar is a semisolid by-product obtained in the destructive distillation of bituminous coal, which functions in cosmetic products as a cosmetic biocide and denaturant-antidandruff agent is also listed as a function, but this is considered an over-the-counter (OTC) drug use. In 2002, Coal Tar was reported to the Food and Drug Administration (FDA) to be used in four formulations, all of which appear to be OTC drug products. Coal Tar is monographed by the FDA as Category I (safe and effective) OTC drug ingredient for use in the treatment of dandruff, seborrhoea, and psoriasis. Coal Tar is absorbed through the skin of animals and humans and is systemically distributed. Although the Cosmetic Ingredient Review (CIR) Expert Panel believes that Coal Tar use as an antidandruff ingredient in OTC drug preparations is adequately addressed by the FDA regulations, the Panel also believes that the appropriate concentration of use of Coal Tar in cosmetic formulations should be that level that does not have a biological effect in the user. Additional data needed to make a safety assessment include product types in which Coal Tar is used (other than as an OTC drug ingredient), use concentrations, and the maximum concentration that does not induce a biological effect in users.

UTILIZATION OF AQUEOUS-TAR CONDENSATES FORMED DURING GASIFICATION

Directory of Open Access Journals (Sweden)

Anna Kwiecińska

2016-11-01

Full Text Available Gasification of solid fuels is an alternative process for energy production using conventional and renewable fuels. Apart from desired compounds, i.e. carbon oxide, hydrogen and methane, the produced gas contains complex organic (tars and inorganic (carbonizate, ammonia contaminants. Those substances, together with water vapor, condensate during cooling of the process gas, what results in the formation of aqueous-tar condensate, which requires proper methods of utilization. The management of this stream is crucial for commercialization and application of the gasification technology. In the paper the treatment of aqueous-tar condensates formed during biomass gasification process is discussed. The removal of tars from the stream was based on their spontaneous separation. The aqueous stream was subjected to ultrafiltration operated at different pressures. Such a treatment configuration enabled to obtain highly concentrated retentate, which could be recycled to the gasifier, and filtrate, which could be subjected to further treatment.

Evaluation of lignite tar

Energy Technology Data Exchange (ETDEWEB)

Gossedin, A

1946-01-01

Tar from the low-temperature (450/sup 0/) carbonization of lignite from Bouches-du-Rhone was hydrogenated in the presence of a catalyst based on MoS/sub 2/ with a 3:1 H:N mixture. Processing (at 470/sup 0/ and 400 atmospheres) for maximum production of gasoline yielded 86 wt % of a product of boiling 55 to 186/sup 0/ and motor octane number 75. An alternative is to hydrogenate with a view to producing solvents and lubricants. For this purpose the tar was separated by distillation (at 20 millimeters, cutting at 220/sup 0/) into two fractions of equal volume. On hydrogenation (at 300/sup 0/ and 400 atmospheres) the light part yields a gasoline H/sub 2/O-soluble cut, a highly aromatic solvent fraction, a heavier cut (280/sup 0/ to 320/sup 0/) suitable as a plasticizer, and a phenol fraction. The heavier part of the tar is hydrogenated (at 380/sup 0/ and 400 atmospheres) to give spindle oil and lubricating oil of medium eta (11.2 centistokes at 98.2/sup 0/), moderate eta index (64), good pour point (-7/sup 0/), and good oxidizing characteristics. The overall yield of products from the two portions is 86.9% (gasoline and solvent 32, light phenols 9.7, spindle oil 14.2, medium lubricating oil 25.7, wax, 5.3%).

Modeling Tar Recirculation in Biomass Fluidized Bed Gasification

NARCIS (Netherlands)

Heineken, Wolfram; De la Cuesta de Cal, Daniel; Zobel, Nico

2016-01-01

A biomass gasification model is proposed and applied to investigate the benefits of tar recirculation within a gasification plant. In the model, tar is represented by the four species phenol, toluene, naphthalene, and benzene. The model is spatially one-dimensional, assuming plug flow for the

Composition of coal tar from pyrolysis and hydropyrolysis of Shenmu coal macerals

Energy Technology Data Exchange (ETDEWEB)

Sun, Q.; Li, W.; Chen, H.; Li, B. [Shandong Academy of Sciences, Jinan (China)

2005-08-15

To understand the relationship of the tar compositions and the coal macerals, the tars obtained from the pyrolysis and hydropyrolysis of Shenmu coal macerals in a fixed-bed reactor were analysed using GC-MS. And the effects of petrographic component, atmosphere and pressure on the yield of aromatic hydrocarbon, phenols, hydrocarbons, oxygen-containing heterocycle and PAHs were systematically investigated. The results show that there is great difference in the composition and the relative content of long chain hydrocarbons, aromatic hydrocarbons, phenols, oxygen-containing heterocycle and PAHs in tars from vitrinite and inertinite pyrolysis. Vitrinite tar contains high content of hydrocarbon with long chain, and inertinite tar contains high content of aromatic hydrocarbons, phenols, oxygen-containing heterocycle and PAHs. It suggests that vitrinite has lower aromaticity and longer chain in its structure than inertinite, which is in well agreement with the result from {sup 13}C NMR and FT-IR test. The tar yield of hydropyrolysis is higher than that of pyrolysis. With increasing the hydrogen pressure, the yield of tar increases greatly. The content of phenols and naphthalene in vitrinite tar form hydropyrolysis under 0.1 MPa is much lower than that form pyrolysis, while that of inertinite tar changes a little. The difference of tar compositions and relative content during pyrolysis and hydropyrolysis reflects the effect of hydrogenation and hydrocracking reactions and the structure characteristics of the macerals. 12 refs., 3 figs.

48 CFR Appendix to Part 1252 - Tar Matrix

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Tar Matrix Appendix to Part 1252 Federal Acquisition Regulations System DEPARTMENT OF TRANSPORTATION CLAUSES AND FORMS SOLICITATION PROVISIONS AND CONTRACT CLAUSES Pt. 1252, App. Appendix to Part 1252—Tar Matrix ER27DE05.000...

Low-temperature tar from bituminous coal and its further treatment

Energy Technology Data Exchange (ETDEWEB)

Hansen, C J

1950-01-01

High-temperature carbonization of bituminous coal yields only 3 to 4 percent tar, as compared with 8 to 10 percent or even more for low-temperature carbonization. The yield of phenols is 20 to 30 times as great from the low-temperature tar. Five conditions that must be met by a satisfactory low-temperature carbonization process are listed. The only method that satisfies all of these conditions is the Brennstoff-Technik (BT) process, in which iron retorts with movable walls are used. One disadvantage of most of the other processes is the high-pitch content of the tar. These tars are processed further to a neutral oil and a phenol-containing oil which are good diesel fuels with high-cetane numbers; the neutral oil can be fractionated to give oils of high-, medium-, and low-cetane number. Attempts to fractionate the tar oil by solvents have not proved commercially useful. However, the tar can be diluted with low-temperature light oil and phenols extracted with NaOH solution without distillation. Some difficulty is found, owing to the simultaneous extraction of viscous resins and other products that are readily removed from the phenols by distillation.

Evaluation of Gravimetric Tar Determination in Particle Samples

DEFF Research Database (Denmark)

Hindsgaul, Claus; Henriksen, Ulrik B.; Bentzen, Jens Dall

2000-01-01

A comparison of tar determination of particles from a down-draft gasifier using soxhlet extractions (with anisole, dichloromethane and acetone) and pyrolysis of the particles.......A comparison of tar determination of particles from a down-draft gasifier using soxhlet extractions (with anisole, dichloromethane and acetone) and pyrolysis of the particles....

Experimental comparison of biomass chars with other catalysts for tar reduction

NARCIS (Netherlands)

Abu El-Rub, Ziad; Bramer, Eduard A.; Brem, Gerrit

2008-01-01

In this paper the potential of using biomass char as a catalyst for tar reduction is discussed. Biomass char is compared with other known catalysts used for tar conversion. Model tar compounds, phenol and naphthalene, were used to test char and other catalysts. Tests were carried out in a fixed bed

Coal-tar based pavement sealant toxicity to freshwater macroinvertebrates

International Nuclear Information System (INIS)

Bryer, Pamela J.; Scoggins, Mateo; McClintock, Nancy L.

2010-01-01

Non-point-source pollution is a major source of ecological impairment in urban stream systems. Recent work suggests that coal-tar pavement sealants, used extensively to protect parking areas, may be contributing a large portion of the polycyclic aromatic hydrocarbon (PAH) loading seen in urban stream sediments. The hypothesis that dried coal-tar pavement sealant flake could alter the macroinvertebrate communities native to streams in Austin, TX was tested using a controlled outdoor laboratory type approach. The treatment groups were: control, low, medium, and high with total PAH concentrations (TPAH = sum of 16 EPA priority pollutant PAHs) of 0.1, 7.5, 18.4, and 300 mg/kg respectively. The low, medium, and high treatments were created via the addition of dried coal-tar pavement sealant to a sterile soil. At the start of the 24-day exposure, sediment from a minimally impacted local reference site containing a community of live sediment-dwelling benthic macroinvertebrates was added to each replicate. An exposure-dependent response was found for several stream health measures and for several individual taxa. There were community differences in abundance (P = 0.0004) and richness (P < 0.0001) between treatments in addition to specific taxa responses, displaying a clear negative relationship with the amount of coal-tar sealant flake. These results support the hypothesis that coal-tar pavement sealants contain bioavailable PAHs that may harm aquatic environments. - Coal-tar pavement sealants degrade stream invertebrate communities.

29 CFR 1910.1002 - Coal tar pitch volatiles; interpretation of term.

Science.gov (United States)

2010-07-01

... 29 Labor 6 2010-07-01 2010-07-01 false Coal tar pitch volatiles; interpretation of term. 1910.1002... Hazardous Substances § 1910.1002 Coal tar pitch volatiles; interpretation of term. As used in § 1910.1000 (Table Z-1), coal tar pitch volatiles include the fused polycyclic hydrocarbons which volatilize from the...

Athabasca tar sand reservoir properties derived from cores and logs

International Nuclear Information System (INIS)

Woodhouse, R.

1976-01-01

Log interpretation parameters for the Athabasca Tar Sand Lease No. 24 have been determined by careful correlation with Dean and Stark core analysis data. Significant expansion of Athabasca cores occurs as overburden pressure is removed. In the more shaly sands the core analysis procedures remove adsorbed water from the clays leading to further overestimation of porosity and free water volume. Log interpretation parameters (R/sub w/ = 0.5 ohm . m and m = n = 1.5) were defined by correlation with the weight of tar as a fraction of the weight of rock solids (grain or dry weight fraction of tar). This quantity is independent of the water content of the cores, whereas porosity and the weight of tar as a fraction of the bulk weight of fluids plus solids (bulk weight fraction) are both dependent on water content. Charts are provided for the conversion of bulk weight fraction of fluids to porosity; grain weight fraction of fluids to porosity; log derived porosity and core grain weight tar to water saturation. Example results show that the core analysis grain weight fraction of tar is adequately matched by the log analyses. The log results provide a better representation of the reservoir fluid volumes than the core analysis data

Corrosion test by low-temperature coal tar

Energy Technology Data Exchange (ETDEWEB)

Ando, S; Yamamoto, S

1952-01-01

Corrosive actions of various fractions of low-temperature coal tar against mild steel or Cr 13-steel were compared at their boiling states. Corrosions became severe when the boiling points exceeded 240/sup 0/. The acidic fractions were more corrosive. In all instances, corrosion was excessive at the beginning of immersion testing and then gradually became mild; boiling accelerated the corrosion. Cr 13-steel was corrosion-resistant to low-temperature coal-tar fractions.

Effect of water addition in a microwave assisted thermal cracking of biomass tar models

International Nuclear Information System (INIS)

Warsita, Aris; Al-attab, K.A.; Zainal, Z.A.

2017-01-01

Highlights: • Effective tar thermal treatment with water addition using microwave is proposed. • The reactor temperature of 1200 °C can be reached quickly at bed height 120 mm. • The optimum water to tar ratio W/T was 0.3 for tar models. • Temperature greatly effect tar removal at various W/T rates. - Abstract: Producer gas from biomass gasification is plagued by the presence of tar which causes pipe blockages. Thermal and catalytic treatments in a microwave reactor have been shown to be effective methods in removing tar from producer gas. A question arises as to the possibility of enhancing the removal mechanism by adding water into the reactor. Toluene and naphthalene were used as tar models in the present study with N_2 as the carrier gas followed by the use of simulated producer gas. Thermal treatment with various amount of water was added at temperatures in the range of 800–1200 °C. The tar removal efficiency obtained 95.83% at the optimum temperature of 1200 °C for naphthalene in for toluene 96.32% at 1050 °C at water to tar ratio (W/T) of 0.3. This study shows that the removal of tar by microwave irradiation with water addition is a significant and effective method in tar cracking.

Sampling of tar from sewage sludge gasification using solid phase adsorption.

Science.gov (United States)

Ortiz González, Isabel; Pérez Pastor, Rosa Ma; Sánchez Hervás, José Ma

2012-06-01

Sewage sludge is a residue from wastewater treatment plants which is considered to be harmful to the environment and all living organisms. Gasification technology is a potential source of renewable energy that converts the sewage sludge into gases that can be used to generate energy or as raw material in chemical synthesis processes. But tar produced during gasification is one of the problems for the implementation of the gasification technology. Tar can condense on pipes and filters and may cause blockage and corrosion in the engines and turbines. Consequently, to minimize tar content in syngas, the ability to quantify tar levels in process streams is essential. The aim of this work was to develop an accurate tar sampling and analysis methodology using solid phase adsorption (SPA) in order to apply it to tar sampling from sewage sludge gasification gases. Four types of commercial SPA cartridges have been tested to determine the most suitable one for the sampling of individual tar compounds in such streams. Afterwards, the capacity, breakthrough volume and sample stability of the Supelclean™ ENVI-Carb/NH(2), which is identified as the most suitable, have been determined. Basically, no significant influences from water, H(2)S or NH(3) were detected. The cartridge was used in sampling real samples, and comparable results were obtained with the present and traditional methods.

Occupational coal tar dermatitis

Energy Technology Data Exchange (ETDEWEB)

Conde-Salazar, L; Guimaraens, D; Romero, L V; Gonzalez, M A

1987-04-01

The paper describes the allergic reaction to coal tar of a man handling it in a factory. The reaction appeared in the form of eczema on his trunk, arms and legs, but his hands were not affected as he had been wearing gloves. 1 ref.

179 Extraction of Coal-tar Pitch by Supercritical Carbon Dioxide ...

African Journals Online (AJOL)

Meyer

Several extractions of coal-tar pitch were performed using supercritical fluid ..... pressure and temperature, unlike exhaustive extraction, which involves a change in ... mechanism that is operative on extracting coal-tar pitch components with.

Contact sensitivity to newsprint: a rare manifestation of coal tar allergy

Energy Technology Data Exchange (ETDEWEB)

Illchyshyn, A; Cartwright, P H; Smith, A G

1987-07-01

Contact dermatitis due to coal tar is infrequently reported in spite of the fact that it consists of a mixture of 10,000 constituents, and is still often used to treat both eczema and psoriasis. Discusses patient with coal tar sensitivity in whom the source of exacerbation of her dermatitis is shown to be newsprint, a common product containing coal tar-derived material. 6 refs.

Coal tar phototoxicity: characteristics of the smarting reaction

International Nuclear Information System (INIS)

Diette, K.M.; Gange, R.W.; Stern, R.S.; Arndt, K.A.; Parrish, J.A.

1985-01-01

The properties and ultraviolet exposure parameters of tar smarts were examined in an effort to elucidate the mechanisms involved. It was show that irradiation with 1 minimal smarting dose (MSD) of UVA immediately following tar removal lowered the MSD for 6 h, demonstrated by subsequent challenge with UVA. Following 3 MSDs this memory effect was demonstrable for 24 h. The smarting reaction was area dependent--smaller areas of exposure require higher doses of UVA to induce smarting. Smarting followed reciprocity over a 6-fold range of irradiances (2-12.5 mW/cm2) but higher irradiances required higher doses of UVA, perhaps due to a delay in the recognition and reporting of smarting. The smarting reaction and delayed erythema due to UVA and tar were equally blocked by sunscreen

Coal-tar based pavement sealant toxicity to freshwater macroinvertebrates

Energy Technology Data Exchange (ETDEWEB)

Bryer, P.J.; Scoggins, M.; McClintock, N.L. [Lamar University, Beaumont, TX (United States). Dept. of Biology

2010-05-15

Non-point-source pollution is a major source of ecological impairment in urban stream systems. Recent work suggests that coal-tar pavement sealants, used extensively to protect parking areas, may be contributing a large portion of the polycyclic aromatic hydrocarbon (PAH) loading seen in urban stream sediments. The hypothesis that dried coal-tar pavement sealant flake could alter the macroinvertebrate communities native to streams in Austin, TX was tested using a controlled outdoor laboratory type approach. The treatment groups were: control, low, medium, and high with total PAH concentrations (TPAH = sum of 16 EPA priority pollutant PAHs) of 0.1, 7.5, 18.4, & 300 mg/kg respectively. The low, medium, and high treatments were created via the addition of dried coal-tar pavement sealant to a sterile soil. At the start of the 24-day exposure, sediment from a minimally impacted local reference site containing a community of live sediment-dwelling benthic macroinvertebrates was added to each replicate. An exposure-dependent response was found for several stream health measures and for several individual taxa. There were community differences in abundance (P = 0.0004) and richness (P < 0.0001) between treatments in addition to specific taxa responses, displaying a clear negative relationship with the amount of coal-tar sealant flake. These results support the hypothesis that coal-tar pavement sealants contain bioavailable PAHs that may harm aquatic environments.

Chemical and physical characteristics of tar samples from selected Manufactured Gas Plant (MGP) sites

International Nuclear Information System (INIS)

Ripp, J.; Taylor, B.; Mauro, D.; Young, M.

1993-05-01

A multiyear, multidisciplinary project concerning the toxicity of former Manufactured Gas Plant (MGP) tarry residues was initiated by EPRI under the Environmental Behavior of Organic Substances (EBOS) Program. This report concerns one portion of that work -- the collection and chemical characterization of tar samples from several former MGP sites. META Environmental, Inc. and Atlantic Environmental Services, Inc. were contracted by EPRI to collect several samples of tarry residues from former MGP sites with varied historical gas production processes and from several parts of the country. The eight tars collected during this program were physically very different. Some tars were fluid and easily pumped from existing wells, while other tars were thicker, semi-solid, or solid. Although care was taken to collect only tar, the nature of the residues at several sites made it impossible not to collect other material, such as soil, gravel, and plant matter. After the samples were collected, they were analyzed for 37 organic compounds, 8 metals, and cyanide. In addition, elemental analysis was performed on the tar samples for carbon, hydrogen, oxygen, sulfur and nitrogen content and several physical/chemical properties were determined for each tar. The tars were mixed together in different batches and distributed to researchers for use in animal toxicity studies. The results of this work show that, although the tars were produced from different processes and stored in different manners, they had some chemical similarities. All of the tars, with the exception of one unusual solid tar, contained similar relative abundances of polycyclic aromatic hydrocarbons (PAHs)

Thermodynamic analysis of tar reforming through auto-thermal reforming process

Energy Technology Data Exchange (ETDEWEB)

Nurhadi, N., E-mail: nurhadi@tekmira.esdm.go.id; Diniyati, Dahlia; Efendi, M. Ade Andriansyah [R& D Centre for Mineral and Coal Technology, Jln. Jend.Sudirman no. 623, Bandung. Telp. 022-6030483 (Malaysia); Istadi, I. [Department of Chemical Engineering, Diponegoro University, Jln. Jl. Prof. Soedarto, SH, Semarang (Malaysia)

2015-12-29

Fixed bed gasification is a simple and suitable technology for small scale power generation. One of the disadvantages of this technology is producing tar. So far, tar is not utilized yet and being waste that should be treated into a more useful product. This paper presents a thermodynamic analysis of tar conversion into gas producer through non-catalytic auto-thermal reforming technology. Tar was converted into components, C, H, O, N and S, and then reacted with oxidant such as mixture of air or pure oxygen. Thus, this reaction occurred auto-thermally and reached chemical equilibrium. The sensitivity analysis resulted that the most promising process performance occurred at flow rate of air was reached 43% of stoichiometry while temperature of process is 1100°C, the addition of pure oxygen is 40% and preheating of oxidant flow is 250°C. The yield of the most promising process performance between 11.15-11.17 kmol/h and cold gas efficiency was between 73.8-73.9%.The results of this study indicated that thermodynamically the conversion of tar into producer gas through non-catalytic auto-thermal reformingis more promising.

Pelagic tar and plastic in the Gulf of Alaska and Bering Sea: 1975

Energy Technology Data Exchange (ETDEWEB)

Shaw, D G

1977-07-01

Seventy-one tows of 740 m/sup 2/ each were made in search of pelagic tar and plastics in the Gulf of Alaska and Bering Sea during the period October 1974 to October 1975. Tar was observed on nine occasions while plastics were found six times. The arithmetic mean value of tar abundance, 3.3 x 10/sup -3/ mg/m/sup 2/, is considerably lower than most other oceanic areas for which values have been reported. Gas chromatographic analysis of this tar indicates that it is more extensively weathered than tar from the north Atlantic. An estimate of the abundance of tar lumps too small to be sampled by net tows is made based on the assumption that there are equal weights of particles in logarithmetically equal size intervals. The abundance of pelagic plastics is also low.

Extraction of low-temperature tar by various alcohols

Energy Technology Data Exchange (ETDEWEB)

Hara, N; Osawa, M; Azuma, H

1948-01-01

MeOH was the most effective of the alcohols tested (MeOH to pentanol) in extracting acid components from low-temperature tar. The optimum concentrations of MeOH were 70 to 80% for 1 extraction and 70 to 75% for repeated or continuous extractions when the solvent-tar ratio was 1:1. By 2 to 3 extractions neutral oil could be separated in about 90% yield including > 3% acidic oil.

Deciphering structure-activity relationships in a series of Tat/TAR inhibitors.

Science.gov (United States)

Pascale, Lise; González, Alejandro López; Di Giorgio, Audrey; Gaysinski, Marc; Teixido Closa, Jordi; Tejedor, Roger Estrada; Azoulay, Stéphane; Patino, Nadia

2016-11-01

A series of pentameric "Polyamide Amino Acids" (PAAs) compounds derived from the same trimeric precursor have been synthesized and investigated as HIV TAR RNA ligands, in the absence and in the presence of a Tat fragment. All PAAs bind TAR with similar sub-micromolar affinities but their ability to compete efficiently with the Tat fragment strongly differs, IC50 ranging from 35 nM to >2 μM. While NMR and CD studies reveal that all PAA interact with TAR at the same site and induce globally the same RNA conformational change upon binding, a comparative thermodynamic study of PAA/TAR equilibria highlights distinct TAR binding modes for Tat competitor and non-competitor PAAs. This led us to suggest two distinct interaction modes that have been further validated by molecular modeling studies. While the binding of Tat competitor PAAs induces a contraction at the TAR bulge region, the binding of non-competitor ones widens it. This could account for the distinct PAA ability to compete with Tat fragment. Our work illustrates how comparative thermodynamic studies of a series of RNA ligands of same chemical family are of value for understanding their binding modes and for rationalizing structure-activity relationships.

Dermal uptake of polycyclic aromatic hydrocarbons after hairwash with coal-tar shampoo

Energy Technology Data Exchange (ETDEWEB)

Schooten, F.-J. van; Moonen, E.J.C.; Rhijnsburger, E.; Agen, B. van; Thijssen, H.H.W.; Kleinjans, J.C.S. [University of Limburg, Maastricht (Netherlands). Dept. of Health Risk Analysis and Toxicology

1994-11-26

Describes an experiment to assess the dermal uptake of polycyclic aromatic hydrocarbons (PAHs) after hairwashing with coal tar antidandruff shampoo. The urinary excretion of 1-hydroxypyrene (1-OH-P), a PAH metabolile was used to assess internal dose of PAH. A single use of coal tar shampoo resulted in increased 1-OH-P excretion in all members of the experimental group compared with the control group using a non-coal tar antidandruff shampoo. It is suggested that repeated use of coal tar shampoo would result in a high internal dose of carcinogenic PAH. 5 refs., 1 fig.

Iron-based materials as tar cracking catalyst in waste gasification

Energy Technology Data Exchange (ETDEWEB)

Nordgreen, Thomas

2011-07-01

The treatment of municipal solid waste (MSW) in Sweden has changed during the past decades due to national legislation and European Union directives. The former landfills have more or less been abandoned in favour of material recycling and waste incineration. On a yearly basis approximately 2.2 million tonnes waste are incinerated in Sweden with heat recovery and to some extent also with electricity generation, though at a low efficiency. It is desirable to alter this utilisation and instead employ MSW as fuel in a fluid bed gasification process. Then electrical energy may be produced at a much higher efficiency. However, MSW contain about 1 % chlorine in the form of ordinary table salt (NaCl) from food scraps. This implies that the tar cracking catalyst, dolomite, which is normally employed in gasification, will suffer from poisoning if applied under such conditions. Then the tar cracking capacity will be reduced or vanish completely with time. Consequently, an alternative catalyst, more resistant to chlorine, is needed. Preliminary research at KTH has indicated that iron in its metallic state may possess tar cracking ability. With this information at hand and participating in the project 'Energy from Waste' an experimental campaign was launched. Numerous experiments were conducted using iron as tar cracking catalyst. First iron sinter pellets from LKAB were employed. They were reduced in situ with a stream of hydrogen before they were applied. Later iron-based granules from Hoeganaes AB were tested. These materials were delivered in the metallic state. In all tests the KTH atmospheric fluidised bed gasifier with a secondary catalytic reactor housing the catalytic material was deployed. Mostly, the applied fuel was birch. The results show that metallic iron possesses an intrinsic ability, almost in the range of dolomite, to crack tars. Calculations indicate that iron may be more resistant to chlorine than dolomite. The exploration of metallic iron

Secondary reactions of tar during thermochemical biomass conversion[Dissertation 14341

Energy Technology Data Exchange (ETDEWEB)

Morf, P.O.

2001-07-01

This dissertation submitted to the Swiss Federal Institute of Technology in Zurich presents and discusses the results obtained during the examination of the processes involved in the formation and conversion of tar in biomass gasification plant. Details are given on the laboratory reactor system used to provide separated tar production and conversion for the purposes of the experiments carried out. The results of analyses made of the tar and the gaseous products obtained after its conversion at various temperatures are presented. The development of kinetic models using the results of the experiments that were carried out is described. The results of the experiments and modelling are compared with the corresponding results obtained using a full-scale down-draft, fixed-bed gasifier. The author is of the opinion that the reaction conditions found in full-scale gasifiers can be well simulated using heterogeneous tar conversion experiments using the lab reactor system.

Tar loads on Omani beaches

International Nuclear Information System (INIS)

Badawy, M.I.; Al-Harthy, F.T.

1991-01-01

Owing to Oman's geographic position and long coastal line, the coastal areas of Oman are particularly vulnerable to oil pollution from normal tanker operations, illegal discharges, and accidental spills as well as local sources of oil input. UNEP carried out a survey on the coasts of Oman to determine the major sources of oil pollution and concluded that the major shoreline pollution problems in Oman arose from operational discharges of oil from passing vessels traffic. The oil, because of the high sea and air temperatures in the area, was subjected to relatively high rates of evaporation and photo-oxidation and tended to arrive at the coast as heavy petroleum particulate residues (tar balls). The aim of the present study was to measure the loads of tar balls in Omani coastal areas and to identify the source of oil pollutants on beaches

Decomposition of tar in gas from updraft gasifier by thermal cracking

DEFF Research Database (Denmark)

Brandt, Peder; Henriksen, Ulrik Birk

2000-01-01

Continuing earlier work with tar reduction by partial oxidation of pyrolysis gas [1] thermal cracking has been evaluated as a gas cleaning process. The work has been focusing on cleaning gas from updraft gasifiers, and the long term purpose is to develop a tar cleaning unit based on thermal...... cracking. An experimental set-up has been built, in which a flow of contaminated gas can be heated up to 1290°C in a reactor made of pure Al2O3. Four measurements were made. Three with gas from a pyrolysis unit simulating updraft gasifier, and one with gas from an updraft gasifier. Cracking temperatures...... was 1200, 1250 and 1290°C, and the residence time at this temperature was 0.5 second. The measurements show that at the selected residence time of 0.5 second, the gas flow in a thermal tar cracking unit has to be heated to at least 1250°C to achieve sufficient tar cleaning. At 1290°C, a tar content as low...

Monitoring of tar contents in gases. Final report

Energy Technology Data Exchange (ETDEWEB)

Petersen, Finn [ChimneyLab Europe ApS, Hadsten (Denmark); Houmann Jakobsen, H. [BioSynergi Proces ApS, Hoersholm (Denmark)

2012-08-15

The purpose of this project is to develop and test a relative cheap and simple online tar measuring method, which can monitor the tar content in product gas from thermal gasification. The measuring principle is absorption of tar from sample gas in Isopropanol (IPA), and measuring on this solution by UV-spectrophotometer. Continuous sampling of tar containing producer gas turned out to be a larger problem than earlier foreseen. The best solution was decided to be sampling with higher flows, and afterwards cleaning the IPA in activated carbon. The ambitions for continuous sampling had to be decreased to 1 week, where the IPA and the activated carbon is contaminated by tar and has to be replaced. However this requires larger amounts of IPA and activated carbon. For IPA the weekly consumption was 12-15 Litres and for activated carbon 10 Litres. The whole analyzer unit turned out to be more complex than first projected, mainly because of the increased amounts of IPA. The best mist filter, with respect to pressure drop, efficiency and retention time is a combination of glass wool and quarts wool. The unit has been tested on gas; 20 kW pellets burner for 116 hours. Harbooere updraft gasifier for 519 hours. Skive fluid bed gasifier for 879 hours. There have during the project period been several simple practical problems such as bubbles in the IPA, increasing pressure drop over the activated carbon bed, dropout of UV data acquisition program and increasing baseline. The principle showed from the beginning some good results, with the limitation of 1 week continuous operation, but at the 5. period in Skive the baseline was increasing all the time, and it was not possible to solve this problem. (LN)

Modelling the low-tar BIG gasification concept[Biomass Integrated gasification

Energy Technology Data Exchange (ETDEWEB)

Andersen, Lars; Elmegaard, B.; Qvale, B.; Henriksen, Ulrrik [Technical univ. of Denmark (Denmark); Bentzen, J.D.; Hummelshoej, R. [COWI A/S (Denmark)

2007-07-01

A low-tar, high-efficient biomass gasification concept for medium- to large-scale power plants has been designed. The concept is named 'Low-Tar BIG' (BIG = Biomass Integrated Gasification). The concept is based on separate pyrolysis and gasification units. The volatile gases from the pyrolysis (containing tar) are partially oxidised in a separate chamber, and hereby the tar content is dramatically reduced. Thus, the investment, and running cost of a gas cleaning system can be reduced, and the reliability can be increased. Both pyrolysis and gasification chamber are bubbling fluid beds, fluidised with steam. For moist fuels, the gasifier can be integrated with a steam drying process, where the produced steam is used in the pyrolysis/gasification chamber. In this paper, mathematical models and results from initial tests of a laboratory Low-Tar BIG gasifier are presented. Two types of models are presented: 1. The gasifier-dryer applied in different power plant systems: Gas engine, Simple cycle gas turbine, Recuperated gas turbine and Integrated Gasification and Combined Cycle (IGCC). The paper determines the differences in efficiency of these systems and shows that the gasifier will be applicable for very different fuels with different moisture contents, depending on the system. 2. A thermodynamic Low-Tar BIG model. This model is based on mass and heat balance between four reactors: Pyrolysis, partial oxidation, gasification, gas-solid mixer. The paper describes the results from this study and compares the results to actual laboratory tests. The study shows, that the Low-Tar BIG process can use very wet fuels (up to 65-70% moist) and still produce heat and power with a remarkable high electric efficiency. Hereby the process offers the unique combination of large scale gasification and low-cost gas cleaning and use of low-cost fuels which very likely is the necessary combination that will lead to a breakthrough of gasification technology. (au)

Structural and dynamic characterization of the upper part of the HIV-1 cTAR DNA hairpin

OpenAIRE

Zargarian, Loussin?; Kanevsky, Igor; Bazzi, Ali; Boynard, Jonathan; Chaminade, Fran?oise; Foss?, Philippe; Mauffret, Olivier

2009-01-01

First strand transfer is essential for HIV-1 reverse transcription. During this step, the TAR RNA hairpin anneals to the cTAR DNA hairpin; this annealing reaction is promoted by the nucleocapsid protein and involves an initial loop?loop interaction between the apical loops of TAR and cTAR. Using NMR and probing methods, we investigated the structural and dynamic properties of the top half of the cTAR DNA (mini-cTAR). We show that the upper stem located between the apical and the internal loop...

Creating fluid injectivity in tar sands formations

Science.gov (United States)

Stegemeier, George Leo; Beer, Gary Lee; Zhang, Etuan

2010-06-08

Methods for treating a tar sands formation are described herein. Methods for treating a tar sands may include heating a portion of a hydrocarbon layer in the formation from one or more heaters located in the portion. The heat may be controlled to increase the permeability of at least part of the portion to create an injection zone in the portion with an average permeability sufficient to allow injection of a fluid through the injection zone. A drive fluid and/or an oxidizing fluid may be provided into the injection zone. At least some hydrocarbons are produced from the portion.

The separate effects of tar and nicotine on the cigarette smoking manoeuvre

International Nuclear Information System (INIS)

Woodman, G.; Newman, S.P.; Paiva, D.; Clarke, S.W.

1987-01-01

The separate effects of tar and nicotine on the cigarette smoking manoeuvre were investigated. Each of ten asymptomatic habitual smokers smoked three different commercially available cigarettes in a randomised order. The brands were chosen such that two had the same tar yield (10 mg) and two had the same nicotine yield (1.4 mg). The volume of smoke inhaled into the lungs was measured by tracing the smoke with the inert gas 81 Kr m . Puffing indices were recorded using an electronic smoking analyser and flowhead/cigarette holder. There was no difference in the total volume of smoke puffed from each of the cigarette brands. With cigarettes of the samme tar level, the total inhaled smoke volume was lower with the higher nicotine cigarette (P<0.05): by contrast, with cigarettes of the same nicotine level, the toal inhaled smoke volume was lower with the lower tar cigarette (P<0.02). Tar and nicotine appear to exercise independent control over the volume of smoke inhaled. (author)

21 CFR 740.18 - Coal tar hair dyes posing a risk of cancer.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Coal tar hair dyes posing a risk of cancer. 740.18... (CONTINUED) COSMETICS COSMETIC PRODUCT WARNING STATEMENTS Warning Statements § 740.18 Coal tar hair dyes... coal tar hair dye containing any ingredient listed in paragraph (b) of this section shall bear, in...

Gasification of municipal solid waste in a downdraft gasifier: Analysis of tar formation

Directory of Open Access Journals (Sweden)

Tabitha Geoffrey Etutu

2016-04-01

Full Text Available In this study, municipal solid waste (MSW from a dumpsite was converted into refuse derived fuel (RDF and used as feedstock for an air-blown gasification process. The gasification process was conducted in a 10 kg.hr -1 downdraft gasifier at different air flow rates of 300, 350, 400, 450 and 550 NL.min1 at atmospheric pressure in order to investigate the quantity and quality of tar formed. It was shown that the increase in the air flow rate from 300 NL.min1 to 550 NL.min1 led to an increase in the oxidation temperature from 719°C to 870°C and an increase in the reduction temperature from 585°C to 750°C, respectively. Tar was reduced from 15 g.Nm3 to 4.7 g.Nm3 respectively. Heavy tar compounds (>C17 e.g. pyrene and phenathrene, decreased with the increase in the light tar compounds (tar reduction through a tar cracking process.

Recovery of very viscous lubricating oils from shale-tar, etc

Energy Technology Data Exchange (ETDEWEB)

Erdmann, E

1919-09-10

Modification of the process covered by German Patent 335,190 for recovering very viscous lubricating oils, consisting, in place of brown-coal tar, deparafinned peat tar being subjected to the treatment with superheated steam from about 200 to 250/sup 0/C or to heating in vacuum at a temperature below 250/sup 0/C.

Anomalous magnetic viscosity in α-Fe(Co)/(Nd,Pr)2Fe14B exchange-spring magnet

International Nuclear Information System (INIS)

Hai, Nguyen Hoang; Chau, Nguyen; Ngo, Duc-The; Gam, Duong Thi Hong

2011-01-01

This article presents an anomalous magnetic viscosity in α-Fe(Co)/(Nd,Pr) 2 Fe 14 B exchange-spring magnet. A similar effect has been observed in non-interacting or weakly interacting systems but not in a strong interacting magnetic systems. We reported a new procedure to measure magnetic relaxation under various magnetic fields. Changing the applied magnetic field by different field protocols during the reversal process, we found that a memory effect of the magnetization appeared if the field change is large enough. The mechanism of the phenomenon can be explained in the model of conventional magnetic reversal in strong ferromagnetic systems with an energy barrier distribution. The study of such magnetic relaxations can provide some information related to the energy barrier distribution function. - Highlights: → The memory effect was observed in a strong magnetically interacting system. → The memory effect on hard magnets can be explained by conventional reversal mechanism. → And it provides some information of the energy barrier for the reversal of magnetic moments.

Technological changes illustrated by the coal tar and tar dye industry; Die Wandlung der Technik am Beispiel der Steinkohlenteer- und Teerfarben-Chemie

Energy Technology Data Exchange (ETDEWEB)

Collin, G. [Deutsche Gesellschaft fuer Chemisches Apparatewesen, Chemische Technik und Biotechnologie e.V. (DECHEMA), Frankfurt am Main (Germany)

2001-05-01

Coal tar was detected in the 17th century in laboratory experiments based on empirical knowledge. In the 18th century industrial revolution, coal tar was an undesired by-product of iron production and coking plants. It was first used in the 19th century for impregnating railway sleepers. Later developments in atomic theory, new chemical symbols and organic element analysis provided the basis for discovering and chemical characterisation of coal tar constituents. Laboratory experiments with these tar constituents resulted in the first synthetic dyes, the postulation of tetravalent carbon and the resulting structural theory in organic chemistry for systematic synthesis of many tar dyes to substitute natural dyes in the textile industry. The technical application of these syntheses was part 2 of the industrial revolution and the foundation of the chemical industry in Germany, which developed rapidly in the 2nd half of the 19th century. Tar dye chemistry has made a significant contribution to Germany's economic growth and the change from an agricultural to an industrialized country. [German] Die Entdeckung des Steinkohlenteers im 17. Jahrhundert basiert auf durch Erfahrungswissen gepraegten Laboratoriumsexperimenten. Im Verlauf der 'Industriellen Revolution' des 18. Jahrhunderts ist der Steinkohlenteer zunaechst ein laestiges Abfallprodukt der Eisengewinnung im Kokshochofen und der Leuchtgasherstellung durch Kohlenverkokung. Erste technische Applikation finden Steinkohlenteeroele im 19. Jahrhundert durch den Eisenbahnbau zur Langzeit-Konservierung der dafuer benoetigten Holzschwellen. Die wissenschaftlichen Erfkenntnisse zur Atomtheorie, eine neue chemische Zeichensprache und die organische Elementaranalyse werden Voraussetzungen zur Entdeckung und chemischen Charakterisierung der Hauptinhaltsstoffe des Steinkohlenteers. Laboratoriumsexperimente mit den entdeckten Teerinhaltsstoffen fuehren zur Erfindung der ersten synthetischen Farbstoffe, die

Inhaled smoke volume and puff indices with cigarettes of different tar and nicotine levels

International Nuclear Information System (INIS)

Woodman, G.; Newman, S.P.; Pavia, D.; Clarke, S.W.

1987-01-01

Ten asymptomatic smokers each smoked a low, low-to-middle and a middle tar cigarette with approximately the same tar-to-nicotine ratio, in a randomised order. The inhaled smoke volume was measured by tracing the smoke with the inert gas 81 Kr m . Puffing indices were recorded using an electronic smoking analyser and flowhead/cigarette holder. Throughout the study neither the mean inhaled smoke volume per puff nor the total inhaled smoke volume per cigarette changed significantly; however, the mean and total puff volumes were largest with the low tar cigarette and decreased with the higher tar brands. Puff volume was related to puff work (r s =0.83,P s =0.10,P>0.1). It is concluded that when switched between brands with the same tar-to-nicotine ratio, smokers increase their puff volumes with a lower tar cigarette but do not change the volume of smoke inhaled. Puff work and puff resistance were significantly correlated (r s =0.45,P<0.02). (author)

Analysis of low-temperature tar fractions

Energy Technology Data Exchange (ETDEWEB)

Kikkawa, S; Yamada, F

1952-01-01

A preliminary comparative study was made on the applicability of the methods commonly used for the type analysis of petroleum products to the low-temperature tar fractions. The usability of chromatography was also studied.

Acid Tar Lagoons: Management and Recovery

Science.gov (United States)

Bohers, Anna; Hroncová, Emília; Ladomerský, Juraj

2017-04-01

This contribution presents the issue with possibility of definitive removal of dangerous environmental burden in Slovakia - serious historical problem of two acid tar lagoons. In relation to their removal, no technology has been found so far - technologically and economically suitable, what caused problems with its management. Locality Predajná is well known in Slovakia by its character of contrasts: it is situated in the picturesque landscape of National Park buffer zone of Nízke Tatry, on the other site it is contaminated by 229 211m3 of acid tar with its characteristics of toxicity, carcinogenicity, teratogenicity, mutagenicity and toxicity especially for animals and plants. Acid tar in two landfills with depth of 1m in case of the first lagoon and 9,5m in case of the second lagoon is a waste product derived from operation of Petrochema Dubová - refinery and petrochemical plant whose activity was to process the crude oil through processes of sulfonation and adsorption technology for producing lubricating and special oils, synthetic detergents and special white oils for cosmetic and medical purposes. A part of acid tar was incinerated in two incineration plats. Concentration of SO2 in combustion gases was too high and it was not possible to decrease it under the value of 2000 mg.mn-3 [LADOMERSKÝ, J. - SAMEŠOVÁ, D.: Reduction in sulfur dioxide emissions waste gases of incineration plant. Acta facultatis ecologiae. 1999, p. 217-223]. That is why it was necessary to put them out of operation. Later, because of public opposition it was not possible to build a new incineration plat corresponding to the state of the art. Even though actual Slovak and European legislative for protection of environment against such impacts, neither of tried methods - bio or non-biologic treatment methods - was proved as suitable for processing or for recovery in the reason of different factors admission: i.e. strong aggressivity, difficulty with handling because of its sludgy and

Assessment of ground-water contamination by coal-tar derivatives, St. Louis Park area, Minnesota

Science.gov (United States)

Hult, M.F.

1984-01-01

Operation of a coal-tar distillation and wood-preserving facility in St. Louis Park, Minnesota, during 1918-72 contaminated ground water with coal-tar derivatives and inorganic chemicals. Coal-tar derivatives entered the groundwater system through three major paths: (1) Spills and drippings that percolated to the water table, (2) surface runoff and plant process water that was discharged to wetlands south of the former plant site, and (3) movement of coal tar directly into bedrock aquifers through a multiaquifer well on the site.

Simulation of Trajectories of Tar Ball Transport to the Goa Coast

Digital Repository Service at National Institute of Oceanography (India)

Suneel, V.; Vethamony, P.; VinodKumar, K.; Babu, M.T.; Prasad, V.S.R.

Arrival of tar balls to the Goa coast during pre- and southwest monsoon seasons has been a regular phenomenon in the past few years. In one such event, we observed tar ball deposits along the Goa coast during August 2010, April 2011 and May 2011...

The Legend of Hot Tar or Pitch as a Defensive Weapon

DEFF Research Database (Denmark)

Atzbach, Rainer

2015-01-01

research. In reality, this way of fighting can only be seen as a legend, i.e. a story with only a relative truth at its core. This paper will examine the origin of this historical tradition and its archaeological and architectural sources. The chemical and physical properties of tar pitch and its...... production and use during the Middle Ages will be discussed with special focus on the application of tar pitch as an ingredient in medieval and post-medieval thermal weapons (especially Greek Fire, the firebomb and the fire arrow). The punishment of tarring and feathering will also be considered...

Ensamblajes urbanos: la TAR y el examen de la ciudad

Directory of Open Access Journals (Sweden)

Ignacio Farías

2011-03-01

Full Text Available Este artículo presenta nuevas perspectivas de investigación y desafíos analíticos que la teoría del actor-red (TAR abre para los estudios urbanos. En primer lugar, se revisan cómo los principios de relacionalidad híbrida y asociatividad plana de la TAR están siendo adoptados en los estudios urbanos para ampliar simétricamente la ecología urbana a no-humanos e impugnar concepciones escalares del espacio y economías urbanas. A continuación, se propone que la TAR trae consigo un desafío más fundamental relativo a la concepción de la ciudad como objeto de estudio. Mientras su comprensión habitual como objeto espacial, entidad político-económica y/o forma sociocultural subraya su carácter singular, estable y delimitado, la TAR permite pensar la ciudad como un objeto múltiple y decentrado. La noción de ensamblajes urbanos se introduce entonces para dar cuenta de la circulación y devenir de la ciudad en múltiples redes híbridas y translocales. El artículo concluye sopesando algunas de las consecuencias de este exámen de la ciudad, especialmente el reposicionamiento del problema de la complejidad, urbana en este caso, como punto, si no de partida, entonces al menos de llegada para la TAR.

Copyrolysis of coal with coke-oven gas. III. Analysis of tar

Energy Technology Data Exchange (ETDEWEB)

Liao, H.; Sun, C.; Li, B.; Liu, Z. [Chinese Academy of Sciences, Taiyuan (China). State Key Laboratory of Coal Conversion, Institute of Coal Chemistry

1998-02-01

Tars from copyrolysis of Xianfeng lignite with coke-oven gas (COG) at different pressures (0.1-5 MPa) and heating rates (5-25{degree}C/min) to a final temperature of 650{degree}C were analyzed and compared with hydropyrolysis under the same H{sub 2} partial pressure. The results indicated that high contents of BTX, PCX and naphthalene were found in the tar from copyrolysis of Xianfeng lignite with COG. Pressure and heating rate have important effects on tar yields and the contents of BTX, PCX and naphthalene in oil. Increasing pressure and decreasing heating rate enhance the tar yields and result in high yields of BTX and PCX. When compared with hydropyrolysis under the same H{sub 2} partial pressure, the tar yield increases by 1.2 times and the yields of BTX, PCX and naphthalene by about 1.6, 1.3 and 1.6 times, respectively. At the same total pressure (3MPa), the yields of BTX and naphthalene from copyrolysis are equal to those from hydropyrolysis. The results reveal that other components in COG, such as methane, carbon monoxide etc., are of importance for pyrolysis behaviour of coal under COG and improvement of oil qualities. 5 refs., 5 figs., 2 tabs.

Relevance of carbon structure to formation of tar and liquid alkane during coal pyrolysis

International Nuclear Information System (INIS)

Liu, Peng; Le, Jiawei; Wang, Lanlan; Pan, Tieying; Lu, Xilan; Zhang, Dexiang

2016-01-01

Highlights: • Curve-fitting method was used to quantify the accurate contents of structural carbon. • Effect of carbon structure in coal with different rank on formation of pyrolysis tar was studied. • Numerical interrelation between carbon types in coal structure and tar yield is elaborated. • Effect of carbon structure on formation of liquid alkane during coal pyrolysis is discussed. - Abstract: The relevance of carbon structure to formation of tar and liquid alkane during coal pyrolysis were discussed extensively. The pyrolysis tests were carried out in a tube reactor at 873 K and keep 15 min. The carbon distribution in coals was investigated by solid state "1"3C nuclear magnetic resonance (N.M.R.). The curve-fitting method was used to quantify the accurate contents of structural carbon. The alkanes in coal tar were analyzed by Gas Chromatograph–Mass Spectrometer (GC–MS). The results show that oxygen-linked aromatic carbon decreases with the increasing of coal rank. The aliphatic carbon contents of Huainan (HN) coal are 44.20%, the highest among the four coals. The carbon types in coal structure have a significant influence on the formation of tar and liquid alkane. The coal tar yields are related to the aliphatic substituted aromatic carbon, CH_2/CH_3 ratio and oxygen-linked carbon in coal so that the increasing order of tar yield is Inner Mongolia lignite (IM, 6.30 wt.%) < Sinkiang coal (SK, 7.55 wt.%) < Shenmu coal (SM, 12.84 wt.%) < HN (16.29 wt.%). The highest contents of oxygen-linked aromatic carbon in IM lead to phenolic compound of 41.06% in IM-tar. The contents of alkane in SM-tar are the highest because the appropriate CH_2/CH_3 ratio and the highest aliphatic side chains on aromatic rings in SM leading to generate aliphatic hydrocarbon with medium molecular weight easily. The mechanism on formation of tar and liquid alkane plays an important role in guiding the industrialization of pyrolysis-based poly-generation producing tar with high

Identification of sources of tar balls deposited along the Goa coast, India, using fingerprinting techniques

International Nuclear Information System (INIS)

Suneel, V.; Vethamony, P.; Zakaria, M.P.; Naik, B.G.; Prasad, K.V.S.R.

2013-01-01

Highlights: ► This is first fingerprinting study in India on identification of source of tar balls. ► Tar balls were formed from tanker-wash spills and they resemble floating tar ball. ► δ 13 C values of Bombay High crude oil and the present tar balls do not match. ► Compound specific stable carbon isotope analysis confirmed the source of tar balls. ► Source is confirmed as the South East Asian Crude Oil and not the Bombay High crude. -- Abstract: Deposition of tar balls along the coast of Goa, India is a common phenomenon during the southwest monsoon. Representative tar ball samples collected from various beaches of Goa and one Bombay High (BH) crude oil sample were subjected to fingerprint analysis based on diagnostic ratios of n-alkane, biomarkers of pentacyclic tri-terpanes and compound specific stable carbon isotope (δ 13 C) analysis to confirm the source. The results were compared with the published data of Middle East Crude Oil (MECO) and South East Asian Crude Oil (SEACO). The results revealed that the tar balls were from tanker-wash derived spills. The study also confirmed that the source is not the BH, but SEACO. The present study suggests that the biomarkers of alkanes and hopanes coupled with stable carbon isotope analysis act as a powerful tool for tracing the source of tar balls, particularly when the source specific biomarkers fail to distinguish the source

29 CFR 1926.1102 - Coal tar pitch volatiles; interpretation of term.

Science.gov (United States)

2010-07-01

... 29 Labor 8 2010-07-01 2010-07-01 false Coal tar pitch volatiles; interpretation of term. 1926.1102 Section 1926.1102 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH... Hazardous Substances § 1926.1102 Coal tar pitch volatiles; interpretation of term. Note: The requirements...

A review of the primary measures for tar elimination in biomass gasification processes

International Nuclear Information System (INIS)

Devi, Lopamudra; Ptasinski, K.J.; Janssen, F.J.J.G.

2003-01-01

Tar formation is one of the major problems to deal with during biomass gasification. Tar condenses at reduced temperature, thus blocking and fouling process equipments such as engines and turbines. Considerable efforts have been directed on tar removal from fuel gas. Tar removal technologies can broadly be divided into two approaches; hot gas cleaning after the gasifier (secondary methods), and treatments inside the gasifier (primary methods). Although secondary methods are proven to be effective, treatments inside the gasifier are gaining much attention as these may eliminate the need for downstream cleanup. In primary treatment, the gasifier is optimized to produce a fuel gas with minimum tar concentration. The different approaches of primary treatment are (a) proper selection of operating parameters, (b) use of bed additive/catalyst, and (c) gasifier modifications. The operating parameters such as temperature, gasifying agent, equivalence ratio, residence time, etc. play an important role in formation and decomposition of tar. There is a potential of using some active bed additives such as dolomite, olivine, char, etc. inside the gasifier. Ni-based catalyst are reported to be very effective not only for tar reduction, but also for decreasing the amount of nitrogenous compounds such as ammonia. Also, reactor modification can improve the quality of the product gas. The concepts of two-stage gasification and secondary air injection in the gasifier are of prime importance. Some aspects of primary methods and the research and development in this area are reviewed and cited in the present paper

Solid state 13 C NMR quantitative study of wood tar pitches

International Nuclear Information System (INIS)

Prauchner, Marcos Juliano; Pasa, Vanya Marcia Duarte; Menezes, Sonia Maria Cabral de

1999-01-01

In this work, solid-state 13 C NMR is used with other techniques to characterize Eucalyptus tar pitches and to follow their polymerization reactions. The pitches are the residues of distillation (about 50% m;m) of the tar generated in Eucalyptus slow pyrolysis for charcoal production in metal industry

29 CFR 1915.1002 - Coal tar pitch volatiles; interpretation of term.

Science.gov (United States)

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Coal tar pitch volatiles; interpretation of term. 1915.1002 Section 1915.1002 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH... Toxic and Hazardous Substances § 1915.1002 Coal tar pitch volatiles; interpretation of term. Note: The...

Avoiding tar formation in biocoke production from waste biomass

International Nuclear Information System (INIS)

Adrados, A.; De Marco, I.; Lopez-Urionabarrenechea, A.; Solar, J.; Caballero, B.

2015-01-01

This paper focuses in avoiding tar formation and in optimizing pyrolysis gas (maximizing H 2 and CO) in the production of biocoke from waste lignocellulosic biomass. In order to obtain metallurgical grade biochar (biocoke) slow heating rate and high temperature are required. Under such conditions useless pyrolysis liquids, mainly composed of water together with some heavy-sticky tars, are obtained. In order to make biocoke a cost-effective process it is necessary to optimize pyrolysis vapors avoiding tar formation and maximizing the amount and quality of both coke and gases. With this objective, in this work different heating rates (3–20 °C min −1 ) and catalysts (zeolite, Ni/CeO 2 –Al 2 O 3 ) have been tested in a two step pyrolysis process. Olive tree cuttings have been pyrolyzed in a 3.5 L batch reactor at 750 °C and the vapors generated have been thermally and catalytically treated at 900 °C in a second tubular reactor. About 25 wt.% biocoke useful as reducing agent in certain metallurgical processes, ≈57 wt.% gases with near 50 vol.% H 2 , and no tar production has been achieved when a heating rate of 3 °C min −1 and the homemade Ni/CeO 2 –Al 2 O 3 catalyst were used. - Highlights: • Metallurgical grade biochar was obtained by olive waste pyrolysis. • Low heating rates avoid tar formation and increase gas and biochar yields. • Ni/CeO 2 –Al 2 O 3 was better than HZSM5 zeolite for vapor upgrading in a second step. • Ni/CeO 2 –Al 2 O 3 and 3 °C min −1 gave the maximum H 2 , gas and biochar yields

Cancer risk estimation for mixtures of coal tars and benzo(a)pyrene

International Nuclear Information System (INIS)

Gaylor, D.W.; Culp, S.J.; Goldstein, L.S.; Beland, F.A.

2000-01-01

Two-year chronic bioassays were conducted by using B6C3F1 female mice fed several concentrations of two different mixtures of coal tars from manufactured gas waste sites or benzo(a)pyrene (BaP). The purpose of the study was to obtain estimates of cancer potency of coal tar mixtures, by using conventional regulatory methods, for use in manufactured gas waste site remediation. A secondary purpose was to investigate the validity of using the concentration of a single potent carcinogen, in this case benzo(a)pyrene, to estimate the relative risk for a coal tar mixture. The study has shown that BaP dominates the cancer risk when its concentration is greater than 6,300 ppm in the coal tar mixture. In this case the most sensitive tissue site is the forestomach. Using low-dose linear extrapolation, the lifetime cancer risk for humans is estimated to be: Risk -4 (ppm coal tar in total diet) + 240 x 10 -4 (ppm BaP in total diet), based on forestomach tumors. If the BaP concentration in the coal tar mixture is less than 6,300 ppm, the more likely case, then lung tumors provide the largest estimated upper limit of risk, Risk -4 (ppm coal tar in total diet), with no contribution of BaP to lung tumors. The upper limit of the cancer potency (slope factor) for lifetime oral exposure to benzo(a)pyrene is 1.2 x 10 -3 per microg per kg body weight per day from this Good Laboratory Practice (GLP) study compared with the current value of 7.3 x 10 -3 per microg per kg body weight per day listed in the US EPA Integrated Risk Information System

Experimental and theoretical evaluation of the performance of a tar solar water heater

International Nuclear Information System (INIS)

Ammari, H.D.; Nimir, Y.L.

2003-01-01

The paper presents an experimental and theoretical evaluation of the performance of a tar solar water heater and comparison with that of a conventional type collector. The performance of both collectors is assessed under the same conditions. Both of the collectors have the same surface area and are glazed. The conventional type has the water tubes welded to the absorber plate, whereas in the tar type, the tar acts as an absorber plate that covers the water tubes. The theoretical model for each collector type, with the transient effects taken into account, is based on a control volume and a time base in the related energy equations. By considering a small element of the collector in each case, three partial differential equations were developed for each collector and were solved numerically by the Runge-Kutta method of the fifth order. A good agreement was achieved between the numerical and experimental results for both the conventional and tar collectors, indicating the feasibility of employing the theoretical model in the design of flat plate solar collectors. The results also showed that the conventional collector is more efficient than the tar type during most of the daylight, but the tar collector had the added advantage of better conservation of energy in late afternoon and evening

Estimating release of polycyclic aromatic hydrocarbons from coal tar at manufactured-gas plant sites

International Nuclear Information System (INIS)

Loehr, R.C.; Rao, P.S.C.; Lee, L.S.; Okuda, I.

1992-08-01

One component of the EPRI's research on Envirorunental Behavior of Organic Substances (EBOS) consists of developing information and models to predict releases of monocyclic and polycyclic aromatic hydrocarbons (MAHs and PAHs) to groundwater from coal tars and contaminated soils at MGP sites. The results of this report focus primarily on release of PAHs from coal tars. There are at least two approaches to predicting the release of organic chemicals from coal tar to water. The simplest method to estimate aqueous concentrations is to assume that water solubility of a PAH compound released from the tar can be defined by equilibrium precipitation-dissolution reactions. Application of Raoult's law is another method to predict aqueous concentrations, which requires the assumption of ''ideal'' behavior for partitioning of PAHs between the tar and water phases. To evaluate the applicability of these two methods for predicting PAH releases, laboratory experiments were conducted with eight coal tar samples from former MGP sites across the country. Migration of chemicals in the environment and resulting contaminant plumes in groundwater are determined by leachate concentrations of the chemicals. The use of equilibrium precipitation-dissolution reactions will usually result in an overestimation of PAH concentrations in the leachate from a coal tar source, and thus the resulting PAH concentrations in groundwater. Raoult's law appears to be a more accurate approach to predicting the release of several PAHs from coal tars. Furthermore, if nonequilibrium conditions prevail, aqueous-phase PAH concentrations will be even lower than those predicted using Raoult's law

Release of polyaromatic hydrocarbons from coal tar contaminated soils

International Nuclear Information System (INIS)

Priddy, N.D.; Lee, L.S.

1996-01-01

A variety of process wastes generated from manufactured gas production (MGP) have contaminated soils and groundwater at production and disposal sites. Coal tar, consisting of a complex mixture of hydrocarbons present as a nonaqueous phase liquid, makes up a large portion of MGP wastes. Of the compounds in coal tar, polyaromatic hydrocarbons (PAHs) are the major constituents of environmental concern due to their potential mutagenic and carcinogenic hazards. Characterization of the release of PAHs from the waste-soil matrix is essential to quantifying long-term environmental impacts in soils and groundwater. Currently, conservative estimates for the release of PAHs to the groundwater are made assuming equilibrium conditions and using relationships derived from artificially contaminated soils. Preliminary work suggests that aged coal tar contaminated soils have much lower rates of desorption and a greater affinity for retaining organic contaminants. To obtain better estimates of desorption rates, the release of PAHs from a coal tar soil was investigated using a flow-interruption, miscible displacement technique. Methanol/water solutions were employed to enhance PAH concentrations above limits of detection. For each methanol/water solution employed, a series of flow interrupts of varying times was invoked. Release rates from each methanol/water solution were estimated from the increase in concentration with duration of flow interruption. Aqueous-phase release rates were then estimated by extrapolation using a log-linear cosolvency model

Experimental Models of Inherited PrP Prion Diseases.

Science.gov (United States)

Watts, Joel C; Prusiner, Stanley B

2017-11-01

The inherited prion protein (PrP) prion disorders, which include familial Creutzfeldt-Jakob disease, Gerstmann-Sträussler-Scheinker disease, and fatal familial insomnia, constitute ∼10%-15% of all PrP prion disease cases in humans. Attempts to generate animal models of these disorders using transgenic mice expressing mutant PrP have produced variable results. Although many lines of mice develop spontaneous signs of neurological illness with accompanying prion disease-specific neuropathological changes, others do not. Furthermore, demonstrating the presence of protease-resistant PrP species and prion infectivity-two of the hallmarks of the PrP prion disorders-in the brains of spontaneously sick mice has proven particularly challenging. Here, we review the progress that has been made toward developing accurate mouse models of the inherited PrP prion disorders. Copyright © 2017 Cold Spring Harbor Laboratory Press; all rights reserved.

Extraction of tar acids with methanol from low-temperature tar

Energy Technology Data Exchange (ETDEWEB)

Funasaka, W; Yokogawa, C; Suga, S

1948-01-01

From 20 grams crude middle oil, boiling at 200/sup 0/ to 250/sup 0/, acid content 40%, tar acids were extracted at 20/sup 0/ to 30/sup 0/ with MeOH for comparison with EtOH, NMe/sub 3/, and ethylene glycol. When 80% MeOH is used, the oil extracted amounts to 61%, including 9% acids, if the ratio of crude oil and solvent is kept at 1:2. EtOH is inferior to MeOH. The properties of the crude oil and the purified oil extracted with 80% MeOH are described.

Tar Removal from Biomass Producer Gas by Using Biochar

DEFF Research Database (Denmark)

Ravenni, Giulia; Henriksen, Ulrik Birk; Ahrenfeldt, Jesper

2017-01-01

The biomass-derived char (biochar) produced in the gasifier as a residue, is a potential solution for removing tars from producer gas. This work investigates the interaction between tar compounds and biochar. Residual biochar from a TwoStage gasifier was tested as bed material in a laboratory setup....... Phenol and naphthalene were chosen as model tars, and entrained in a nitrogen flow. The gaseous stream was sampled before and after the biochar bed to evaluate the extent of conversion. The biochar bed (30g) was tested at 250°C, 500°C and 600°C, with for 3 consecutive hours. The compounds concentration...... in the gas phase was quantified by stable isotope dilution analysis, using Gas Chromatography-Mass Spectrometry (GC-MS). Results showed a significant effect of biochar on the removal of phenol, at all temperatures. Naphthalene was removed less efficiently at higher temperature, and this trend was even more...

Solvent refining of low-temperature tar with liquid ammonia

Energy Technology Data Exchange (ETDEWEB)

Ishida, K

1953-01-01

The middle fractions of low-temperature tar were treated with mixed solutions of H/sub 2/O and liquid NH/sub 3/ at 0/sup 0/ and 20/sup 0/, and with liquid NH/sub 3/ at -10, 0, + 10, and 20/sup 0/, and phase equilibrium between tar acids, neutral oil, and solvents were studied. The distribution ratio ranged from less than 1 to greater than 1 when the solvent contained about 20 percent (by weight) H/sub 2/O. When the solvent contained less than 85 percent (by weight) NH/sub 3/, the yield of extract was small but the purity of phenols in the extracted oil was above 90 percent. Solvent containing about 85 percent NH/sub 3/ (by weight) is considered optimum for separating tar acids from oils. A novel definition is proposed for solvent selectivity as the difference between the concentration of the solute in the extract layer, on a solvent-free basis, and the concentration in the raffinate layer.

Ukrainian brown-coal tars recovered at low-temperature carbonization with solid heating medium

Energy Technology Data Exchange (ETDEWEB)

Kuznetsov, V I; Govorova, R P; Fadeicheva, A G; Kigel, T B; Chernykh, M K

1955-01-01

Three samples of tar were recovered in the laboratory from brown coals carbonized at 375/sup 0/ to 456/sup 0/ +- 25/sup 0/ in a retort with inner heating by solid circulating medium, namely, semicoke (ratio: 4 or 3:1) first heated to 700/sup 0/. One comparative (parallel) experiment was carried out in a retort with inner heating by inert gases entering the retort at 580/sup 0/ to 600/sup 0/ and leaving it at 115/sup 0/ to 120/sup 0/. The tars that were recovered from the retort with the solid heating medium contained a high percentage of coal dust and moisture, which were separated from the tars in supercentrifuges (15,000 rpm). Four samples of cleaned tars were fractionated in a Cu flask with a 2-ball fractional column. The tars from the retort with the solid-heating medium are characterized by increased yield of the petroleum-ether fraction (16.3 or 19.3%) and decreased yield of the paraffin fraction (15.1 to 21.2%) in comparison with those of tar from the retort with gas heating (5.9% of the petroleum ether fraction and 36.5% of paraffin fraction). The yield of paraffin from the paraffin fraction also decreased from 90.6% to 62.6-74.3%. This result shows that in the first case the carbonized products were cracked to a higher degree than those from the retort with gas heating. In raw phenols recovered from fractions of investigated tars, the yield of the phenol-cresol fraction (182/sup 0/ to 204/sup 0/) decreased from 25.9% to 13.0-18.9%.

Analysis of the environmental control technology for tar sand development

Energy Technology Data Exchange (ETDEWEB)

de Nevers, N.; Glenne, B.; Bryner, C.

1979-06-01

The environmental technology for control of air pollution, water pollution, and for the disposal, stabilization, and vegetation of the waste tar sand were thoroughly investigated. Although some difficulties may be encountered in any of these undertakings, it seems clear that the air and water pollution problems can be solved to meet any applicable standard. Currently there are two large-scale plants producing liquid fuels from tar sands in Alberta, Canada which use similar technology involving surface mining, hot water extraction, and surface disposal of waste sand. These projects all meet the Canadian environmental control regulations in force at the time they began. The largest US deposits of tar sands are much smaller than the Canadian; 95 percent are located in the state of Utah. Their economics do not appear as attractive as the Canadian deposits. The environmental control costs are not large enough to make an otherwise economic project uneconomic. The most serious environmental conflict likely to occur over the recovery of liquid fuels from the US deposits of tar sands is that caused by the proximity of the deposits to national parks, national monuments, and a national recreation area in Utah. These areas have very stringent air pollution requirements; and even if the air pollution control requirements can be met, there may still be adequate opposition to large-scale mining ventures in these areas to prevent their commercial exploitation. Another environmental constraint may be water rights availability.Essentially all of the water running in the Colorado river basin is now legally allocated. Barring new interpretations of the legality of water rights purchase, Utah tar sands developments should be able to obtain water by purchasing existing irrigation water rights.

Catalytic decomposition of tar derived from wood waste pyrolysis using Indonesian low grade iron ore as catalyst

Energy Technology Data Exchange (ETDEWEB)

Wicakso, Doni Rahmat [Chemical Engineering Department, Faculty of Engineering, Lambung Mangkurat University, Jalan A. Yani KM. 36 Banjarbaru, 70714, South Kalimantan (Indonesia); Chemical Engineering Department, Faculty of Engineering, Gadjah Mada University, Jalan Grafika No. 2 Bulaksumur, Yogyakarta, 55281 (Indonesia); Sutijan; Rochmadi [Chemical Engineering Department, Faculty of Engineering, Gadjah Mada University, Jalan Grafika No. 2 Bulaksumur, Yogyakarta, 55281 (Indonesia); Budiman, Arief, E-mail: abudiman@ugm.ac.id [Chemical Engineering Department, Faculty of Engineering, Gadjah Mada University, Jalan Grafika No. 2 Bulaksumur, Yogyakarta, 55281 (Indonesia); Center for Energy Studies, Gadjah Mada University, Sekip K1A, Yogyakarta, 55281 (Indonesia)

2016-06-03

Low grade iron ore can be used as an alternative catalyst for bio-tar decomposition. Compared to other catalysts, such as Ni, Rd, Ru, Pd and Pt, iron ore is cheaper. The objective of this research was to investigate the effect of using low grade iron ore as catalyst for tar catalytic decomposition in fixed bed reactor. Tar used in this experiment was pyrolysis product of wood waste while the catalyst was Indonesian low grade iron ore. The variables studied were temperatures between 500 – 600 °C and catalyst weight between 0 – 40 gram. The first step, tar was evaporated at 450 °C to produce tar vapor. Then, tar vapor was flowed to fixed bed reactor filled low grade iron ore. Gas and tar vapor from reactor was cooled, then the liquid and uncondensable gas were analyzed by GC/MS. The catalyst, after experiment, was weighed to calculate total carbon deposited into catalyst pores. The results showed that the tar components that were heavy and light hydrocarbon were decomposed and cracked within the iron ore pores to from gases, light hydrocarbon (bio-oil) and carbon, thus decreasing content tar in bio-oil and increasing the total gas product. In conclusion, the more low grade iron ore used as catalyst, the tar content in the liquid decrease, the H{sup 2} productivity increased and calorimetric value of bio-oil increased.

Phytotoxicity and Plant Productivity Analysis of Tar-Enriched Biochars

Science.gov (United States)

Keller, M. L.; Masiello, C. A.; Dugan, B.; Rudgers, J. A.; Capareda, S. C.

2008-12-01

Biochar is one of the three by-products obtained by the pyrolysis of organic material, the other two being syngas and bio-oil. The pyrolysis of biomass has generated a great amount of interest in recent years as all three by-products can be put toward beneficial uses. As part of a larger project designed to evaluate the hydrologic impact of biochar soil amendment, we generated a biochar through fast pyrolysis (less than 2 minutes) of sorghum stock at 600°C. In the initial biochar production run, the char bin was not purged with nitrogen. This inadvertent change in pyrolysis conditions produced a fast-pyrolysis biochar enriched with tars. We chose not to discard this batch, however, and instead used it to test the impact of tar-enriched biochars on plants. A suite of phytotoxicity tests were run to assess the effects of tar-rich biochar on plant germination and plant productivity. We designed the experiment to test for negative effects, using an organic carbon and nutrient-rich, greenhouse- optimized potting medium instead of soil. We used Black Seeded Simpson lettuce (Lactuca sativa) as the test organism. We found that even when tars are present within biochar, biochar amendment up to 10% by weight caused increased lettuce germination rates and increased biomass productivity. In this presentation, we will report the statistical significance of our germination and biomass data, as well as present preliminary data on how biochar amendment affects soil hydrologic properties.

Carbon materials for syngas conditioning and tar removal

International Nuclear Information System (INIS)

Romero Millán, Lina María; Sierra Vargas, Fabio Emiro

2017-01-01

Within the framework of worldwide energy context, the development of technologies and processes for energy production form renewable and non-conventional sources is a priority. According to this, gasification is an interesting process that converts different kinds of organic materials in fuel gases. The main issue related with this process is the fact that the producer gas contains also contaminants and tars that are undesirable for the gas usage in internal combustion motors or turbines. The present work aims to analyze the actual state of the existing methods to remove tars form gasification fuel gases, emphasizing the use of different kinds of carbon materials. (author)

Process from removing benzine, toluene, etc. , from petroleum residues, coal tar, and shale tar, etc

Energy Technology Data Exchange (ETDEWEB)

Hlawaty, F

1888-08-11

A process is described for the preparation of ligroin and its homologs as well as naphthalene and anthracene consisting in leading superheated water vapor into a mixture of petroleum residues (or mineral coal tar, etc.) heated to about 400/sup 0/C with cellulosic substances as sage shreds, sea grass, or straw, with addition of caustic alkali.

Carbazole is a naturally occurring inhibitor of angiogenesis and inflammation isolated from antipsoriatic coal tar

Energy Technology Data Exchange (ETDEWEB)

Jack L. Arbiser; Baskaran Govindarajan; Traci E. Battle; Rebecca Lynch; David A. Frank; Masuko Ushio-Fukai; Betsy N. Perry; David F. Stern; G. Tim Bowden; Anquan Liu; Eva Klein; Pawel J. Kolodziejski; N. Tony Eissa; Chowdhury F. Hossain; Dale G. Nagle [Emory University School of Medicine, Atlanta, GA (United States). Department of Dermatology

2006-06-15

Coal tar is one of the oldest and an effective treatment for psoriasis. Coal tar has been directly applied to the skin, or used in combination with UV light as part of the Goeckerman treatment. The use of coal tar has caused long-term remissions in psoriasis, but has fallen out of favor because the treatment requires hospitalization and coal tar is poorly acceptable aesthetically to patients. Thus, determining the active antipsoriatic component of coal tar is of considerable therapeutic interest. We fractionated coal tar into its components, and tested them using the SVR angiogenesis inhibitor assay. Treatment of SVR endothelial cells with coal tar fractions resulted in the isolation of a single fraction with antiangiogenic activity. The active antiangiogenic compound in coal tar is carbazole. In addition to antiangiogenic activity, carbazole inhibited the production of inflammatory IL-15 by human mononuclear cells. IL-15 is elevated in psoriasis and is thought to contribute to psoriatic inflammation. Carbazole treatment also reduced activity of inducible nitric oxide synthase (iNOS), which is proinflammatory and elevated in psoriasis. The effect of carbazole on upstream pathways in human psoriasis was determined, and carbazole was shown to inhibit signal transducer and activator of transcription (stat)3-mediated transcription, which has been shown to be relevant in human psoriasis. IL-15, iNOS, and stat3 activation require the activation of the small GTPase rac for optimal activity. Carbazole was found to inhibit rac activation as a mechanism for its inhibition of downstream inflammatory and angiogenic pathways. Given its antiangiogenic and anti-inflammatory activities, carbazole is likely a major component of the antipsoriatic activity of coal tar. Carbazole and derivatives may be useful in the therapy of human psoriasis.

Comprehensive database of Manufactured Gas Plant tars. Part C. Heterocyclic and hydroxylated polycyclic aromatic hydrocarbons.

Science.gov (United States)

Gallacher, Christopher; Thomas, Russell; Lord, Richard; Kalin, Robert M; Taylor, Chris

2017-08-15

Coal tars are a mixture of organic and inorganic compounds that were by-products from the manufactured gas and coke making industries. The tar compositions varied depending on many factors such as the temperature of production and the type of retort used. For this reason a comprehensive database of the compounds found in different tar types is of value to understand both how their compositions differ and what potential chemical hazards are present. This study focuses on the heterocyclic and hydroxylated compounds present in a database produced from 16 different tars from five different production processes. Samples of coal tar were extracted using accelerated solvent extraction (ASE) and derivatized post-extraction using N,O-bis(trimethylsilyl)trifluoroacetamide (BSTFA) with 1% trimethylchlorosilane (TMCS). The derivatized samples were analysed using two-dimensional gas chromatography combined with time-of-flight mass spectrometry (GCxGC/TOFMS). A total of 865 heterocyclic compounds and 359 hydroxylated polycyclic aromatic hydrocarbons (PAHs) were detected in 16 tar samples produced by five different processes. The contents of both heterocyclic and hydroxylated PAHs varied greatly with the production process used, with the heterocyclic compounds giving information about the feedstock used. Of the 359 hydroxylated PAHs detected the majority would not have been be detected without the use of derivatization. Coal tars produced using different production processes and feedstocks yielded tars with significantly different heterocyclic and hydroxylated contents. The concentrations of the individual heterocyclic compounds varied greatly even within the different production processes and provided information about the feedstock used to produce the tars. The hydroxylated PAH content of the samples provided important analytical information that would otherwise not have been obtained without the use of derivatization and GCxGC/TOFMS. Copyright © 2017 John Wiley & Sons, Ltd.

Tar removal from biosyngas in the biomass gasification process. (Liquid + liquid) equilibrium {water + solvent (paraxylene and methyl hexadecanoate) + model molecules of tar (benzene, toluene, phenol)}

International Nuclear Information System (INIS)

Bassil, Georgio; Mokbel, Ilham; Abou Naccoul, Ramy; Stephan, Juliette; Jose, Jacques; Goutaudier, Christelle

2012-01-01

Highlights: ► (Liquid + liquid) equilibria at atmospheric pressure. ► Solubility of benzene (or toluene or phenol) in paraxylene at (303 to 343) K. ► Solubility of benzene (or toluene or phenol) in methyl palmitate or methyl hexadecanoate at (303 to 343) K. ► Correlation of LLE using NRTL model. - Abstract: Tar is generated in the process by the condensation of the gas resulting from biomass gasification. The objective of this work is a contribution to the database on thermodynamic quantity which will be useful at the operation of tar removal from aqueous medium. With this aim, (liquid + liquid) equilibrium of {water + solvent (paraxylene and methyl hexadecanoate) + model molecules of tar (benzene, toluene, phenol)} was studied at temperatures (303.2, 323.2, and 343.2) K. The data obtained were correlated with the non-random two-liquid (NRTL) model.

Influence of cigarette filter ventilation on smokers' mouth level exposure to tar and nicotine.

Science.gov (United States)

Caraway, John W; Ashley, Madeleine; Bowman, Sheri A; Chen, Peter; Errington, Graham; Prasad, Krishna; Nelson, Paul R; Shepperd, Christopher J; Fearon, Ian M

2017-12-01

Cigarette filter ventilation allows air to be drawn into the filter, diluting the cigarette smoke. Although machine smoking reveals that toxicant yields are reduced, it does not predict human yields. The objective of this study was to investigate the relationship between cigarette filter ventilation and mouth level exposure (MLE) to tar and nicotine in cigarette smokers. We collated and reviewed data from 11 studies across 9 countries, in studies performed between 2005 and 2013 which contained data on MLE from 156 products with filter ventilation between 0% and 87%. MLE among 7534 participants to tar and nicotine was estimated using the part-filter analysis method from spent filter tips. For each of the countries, MLE to tar and nicotine tended to decrease as filter ventilation increased. Across countries, per-cigarette MLE to tar and nicotine decreased as filter ventilation increased from 0% to 87%. Daily MLE to tar and nicotine also decreased across the range of increasing filter ventilation. These data suggest that on average smokers of highly ventilated cigarettes are exposed to lower amounts of nicotine and tar per cigarette and per day than smokers of cigarettes with lower levels of ventilation. Copyright © 2017 British American Tobacco. Published by Elsevier Inc. All rights reserved.

Creating and maintaining a gas cap in tar sands formations

Science.gov (United States)

Vinegar, Harold J.; Karanikas, John Michael; Dinkoruk, Deniz Sumnu; Wellington, Scott Lee

2010-03-16

Methods for treating a tar sands formation are disclosed herein. Methods for treating a tar sands formation may include providing heat to at least part of a hydrocarbon layer in the formation from one or more heaters located in the formation. Pressure may be allowed to increase in an upper portion of the formation to provide a gas cap in the upper portion. At least some hydrocarbons are produced from a lower portion of the formation.

The documentation of tar balls on oiled shorelines : lessons from the New Carissa, Oregon

International Nuclear Information System (INIS)

Owens, E.H.; Zimlicki-Owens, L.M.; Lamarche, A.; Reimer, P.D.; Martin, C.A.

2000-01-01

The New Carissa, carrying approximately 400,000 gallons of fuel oils ran aground on the outer shore of North Spit, in the vicinity of Coos Bay, Oregon, on February 4, 1999. The oil was released directly into the nearshore surf zone. Following the spill, a stretch of approximately 300 km of the coast of Oregon was surveyed and monitored. The need for the documentation of stranded tar balls in the neighbourhood of the spill site prompted the implementation of a long-term observation program. Initially, Shoreline Clean-up and Assessment Technique (SCAT) reporting procedures were required. Heavy oiling was followed by stranded oil taking the form of tar balls. The amount of oil on the shoreline decreased and the SCAT procedures alone were no longer adequate. They provided estimations of oil quantities that were too high and failed to provide any discrimination between amounts of oil observed on the beaches. A new reporting technique called Beach Assessment Reporting was designed to overcome the difficulties and record adequately the character and frequency of stranded tar balls. Maps, tables and histograms of stranded tar ball volumes and concentrations were discussed. Since the data spanned nine orders of magnitude at times, the semi-logarithmic scale time series plots of the concentration of the tar balls was used in order to identify trends. Conventional histograms only identified large values and camouflaged smaller trends in the time series. A direct method for describing tar ball concentrations geographically proved to be the use of weekly maximum tar ball concentration maps by segment. 10 refs., 2 tabs., 9 figs

Comparative assessment of coal tars obtained from 10 former manufactured gas plant sites in the eastern United States

Energy Technology Data Exchange (ETDEWEB)

Brown, D.G.; Gupta, L.; Kim, T.H.; Moo-Young, H.K.; Coleman, A.J. [Lehigh University, Bethlehem, PA (United States). Dept. of Civil & Environmental Engineering

2006-11-15

A comparative analysis was performed on eleven coal tars obtained from former manufactured gas plant sites in the eastern United States. Bulk properties analyzed included percent ash, Karl Fisher water content, viscosity and average molecular weight. Chemical properties included monocyclic- and polycyclic-aromatic hydrocarbon (PAH) concentrations, alkylated aromatic concentrations, and concentrations of aliphatic and aromatic fractions. It was found that there was at least an order-of-magnitude variation in all properties measured between the eleven coal tars. Additionally, two coal tars obtained from the same manufactured gas plant site had very different properties, highlighting that there can be wide variations in coal tar properties from different samples obtained from the same site. Similarities were also observed between the coal tars. The relative chemical distributions were similar for all coal tars, and the coal tars predominantly consisted of PAHs, with naphthalene being the single-most prevalent compound. The C{sub 9-22} aromatic fraction, an indicator of all PAHs up to a molecular weight of approximately 276 g mole{sup -1}, showed a strong power-law relationship with the coal tar average molecular weight (MWct). And the concentrations of individual PAHs decreased linearly as MWct increased up to ca. 1000 g mole{sup -1}, above which they remained low and variable. Implications of these properties and their variation with MWct on groundwater quality are discussed. Ultimately, while these similarities do allow generalities to be made about coal tars, the wide range of coal tar bulk and chemical properties reported here highlights the complex nature of coal tars.

Physicochemical Approaches for the Remediation of Former Manufactured Gas Plant Tars

Science.gov (United States)

Hauswirth, S.; Miller, C. T.

2014-12-01

Former manufactured gas plant (FMGP) tars are one of the most challenging non-aqueous phase liquid (NAPL) contaminants to remediate due to their complex chemical composition, high viscosities, and ability to alter wettability. In this work, we investigate several in situ remediation techniques for the removal of tar from porous media. Batch and column experiments were conducted to test the effectiveness of mobilization, solubilization, and chemical oxidation remediation approaches. Alkaline (NaOH), surfactant (Triton X-100), and polymer (xanthan gum) agents were used in various combinations to reduce tar-water interfacial tension, increase flushing solution viscosity, and increase the solubilities of tar components. Base-activated sodium persulfate was used alone and in combination with surfactant to chemically oxidized tar components. The effectiveness of each method was assessed in terms of both removal of PAHs from the system and reduction of dissolved-phase effluent polycyclic aromatic hydrocarbon (PAH) concentrations. In column studies, alkaline-polymer (AP) and alkaline-surfactant-polymer (ASP) solutions efficiently mobilized 81-93% and 95-96% of residual PAHs, respectively, within two pore volumes. The impact of AP flushing on dissolved-phase PAH concentrations was relatively low; however, the concentrations of several low molar mass PAHs were significantly reduced after ASP flushing. Surfactant-polymer (SP) solutions removed over 99% of residual PAHs through a combination of mobilization and solubilization, and reduced the post-remediation, dissolved-phase total PAH concentration by 98.4-99.1%. Degradation of residual PAHs by base-activated sodium persulfate was relatively low (30-50%), and had little impact on dissolved-phase PAH concentrations.

Cold Preparation of Heroin in a Black Tar Market.

Science.gov (United States)

Roth, Alexis M; Armenta, Richard F; Wagner, Karla D; Strathdee, Steffanie A; Goldshear, Jesse L; Cuevas-Mota, Jazmine; Garfein, Richard S

2017-07-29

Black tar heroin is typically prepared for injection with heat which decreases the risk of HIV transmission by inactivating the virus. We received reports that persons who inject drugs (PWID) in Tijuana, Baja California, Mexico, a black tar heroin market, were using only water to dissolve heroin. Because Tijuana abuts San Diego County, CA, United States, we undertook the present analyses to determine the prevalence of this practice among PWID in San Diego, California. PWID completed quarterly behavioral assessments and serological testing for blood-borne viruses. Bivariate and multivariable logistic regression models were constructed to assess for individual, social, and structural correlates of preparing heroin without heat within the preceding 6 months. Nearly half of black tar heroin users (149/305) reported they had prepared heroin without heat within 6 months. In multivariable analysis, cold preparation was independently associated with younger age (10 year decrease; AOR = 1.25; 95% CI 1.03, 1.53), more drug injecting acquaintances (per 5 acquaintance increase; AOR = 1.05; 95% CI 1.01, 1.09) and prefilled syringe use (injecting drugs from syringes that are already filled with drugs before purchase; AOR = 1.86; 95% CI 1.14, 3.02). Conclusions/Importance: To our knowledge, this is the first paper to report that PWID living in a black tar heroin market are preparing heroin without heat. Additional research is needed to determine whether this is an endemic practice or PWID are engaging in new forms of drug preparation in response to changes in the environment.

Photoemission of heavy fermion superconductor PrOs4Sb12 and other Pr compounds

International Nuclear Information System (INIS)

Imada, S.; Yamasaki, A.; Sekiyama, A.; Settai, R.; Onuki, Y.; Suga, S.; Sugawara, H.; Sato, H.; Ochiai, A.

2004-01-01

Full text: Strongly correlated electronic states due to Pr 4f electrons found in several Pr compounds have recently been attracting much attention. The Pr 4f electrons are much more localized than in Ce due to the lanthanoid contraction. Therefore, the number of the Pr systems that show strong electron correlation is much smaller than Ce systems. We will present a comparative study of Pr 4f electronic states in such systems as the heavy fermion superconductor PrOs 4 Sb 12 , the Kondo system PrSn 3 and the localized 4f systems Pr 4 X 3 (X = Sb and Bi). The Pr 4f electronic state was probed by means of the Pr 3d → 4f resonant photoemission (RPES). Because the kinetic energy (E K ) of the photoelectrons is as high as ∼ 900 eV, this method is much more bulk sensitive than the 4d → 4f RPES with E K ∼ 100 eV. The energy resolution could be set to about 100 meV by utilizing the soft X-rays from BL25SU in SPring-8 and the SCIENTA SES-200 analyzer. The Pr 4f excitation spectrum of PrSn 3 was found to show a very strong intensity at the Fermi level (E F ). This can be interpreted as the Kondo resonance which has been observed in the Kondo Ce and Yb compounds. In the Pr 4f spectrum of the heavy fermion superconductor PrOs 4 Sb 12 , the intensity at E F was smaller than in PrSn 3 . This clearly shows that the Kondo temperature (T K ) is much lower in PrOs 4 Sb 12 than in PrSn 3 . We have further found a strong excitation energy dependence in the RPES line shape. In the case of Pr 4 X 3 (X = Sb and Bi), the intensity at E B was much smaller than PrSn 3 and PrOs 4 Sb 12 , which is consistent with the localized character of Pr 4f electrons in Pr 4 X 3 . The Pr 4f spectra of these localized systems are qualitatively well reproduced by a cluster model calculation that takes into account the hybridization between the Pr 4f orbital and the conduction and valence bands made up by the X p and Pr 5d states

The purification of coal tar by the addition of quinoline and Zn(oh)/sub 2/

International Nuclear Information System (INIS)

Zhou, P.; Chen, Q.L.; Ao, X.Q.; Kang, C

2017-01-01

The coal tar was purified by the addition of quinoline and Zn(OH)2, in order to decrease the content of carbon and inorganic oxide particles. The effect on the viscosity and ash content of the coal tar were investigated by altering temperature, time, and the amount of quinolone and Zn(OH)2 . When the volume ratio between quinolone and coal tar was 20:1 and the static time was 24 h. The viscosity of three layers decreased with rising temperature. When the static temperature and time was 45 °C and 24 h, respectively. The viscosity of three layers decreased with the arising amount of quinoline. And when the volume ratio between quinolone and coal tar was 20:1 and the temperature was 45 °C. The viscosity of three layers decreased first and then increased with the prolonging of static time. And when the static time of coal tar was 24 h, the viscosity of coal tar is the lowest. Because of the lower viscosity of coal tar, decreasing the content of carbon and ash particles in upper and middle layer, the ash content decreased from 0.168% to 0.092%. The addition of Zn(OH)2 can lead ash content in middle layer decrease to 0.058%. Zn2SiO4 and ZnAl2O4 may be produced due to the reaction between Zn (OH) 2 and SiO2 or Al2O3, which can settle down easily. The results show that the content of carbon and inorganic oxide particles in upper-middle-class (the middle 4/5 of the whole volume) decreased with the addition of quinolone and Zn(OH)2 . When the volume ratio between quinolone and coal tar was 50:2, quality ratio between coal tar and Zn(OH)2 was 20000:1, the mixture were heated up to 45 °C at atmospheric pressure and keeping this constant temperature for 24 h, the ash content in upper-middle-class can decreased to 0.058%. (author)

Opening of the TAR hairpin in the HIV-1 genome causes aberrant RNA dimerization and packaging

Directory of Open Access Journals (Sweden)

Das Atze T

2012-07-01

Full Text Available Abstract Background The TAR hairpin is present at both the 5′ and 3′ end of the HIV-1 RNA genome. The 5′ element binds the viral Tat protein and is essential for Tat-mediated activation of transcription. We recently observed that complete TAR deletion is allowed in the context of an HIV-1 variant that does not depend on this Tat-TAR axis for transcription. Mutations that open the 5′ stem-loop structure did however affect the leader RNA conformation and resulted in a severe replication defect. In this study, we set out to analyze which step of the HIV-1 replication cycle is affected by this conformational change of the leader RNA. Results We demonstrate that opening the 5′ TAR structure through a deletion in either side of the stem region caused aberrant dimerization and reduced packaging of the unspliced viral RNA genome. In contrast, truncation of the TAR hairpin through deletions in both sides of the stem did not affect RNA dimer formation and packaging. Conclusions These results demonstrate that, although the TAR hairpin is not essential for RNA dimerization and packaging, mutations in TAR can significantly affect these processes through misfolding of the relevant RNA signals.

Material Properties and Characteristics for Development of an Expert System for Coal-Tar Sealers

National Research Council Canada - National Science Library

Shoenberger, James

2001-01-01

.... Several coal-tar mixtures that varied with source of the coal-tar emulsion, amount of aggregate, and amount of polymer used in the mixtures were evaluated for their field performance and material properties...

Paleontological overview of oil shale and tar sands areas in Colorado, Utah, and Wyoming.

Energy Technology Data Exchange (ETDEWEB)

Murphey, P. C.; Daitch, D.; Environmental Science Division

2009-02-11

In August 2005, the U.S. Congress enacted the Energy Policy Act of 2005, Public Law 109-58. In Section 369 of this Act, also known as the ''Oil Shale, Tar Sands, and Other Strategic Unconventional Fuels Act of 2005,'' Congress declared that oil shale and tar sands (and other unconventional fuels) are strategically important domestic energy resources that should be developed to reduce the nation's growing dependence on oil from politically and economically unstable foreign sources. In addition, Congress declared that both research- and commercial-scale development of oil shale and tar sands should (1) be conducted in an environmentally sound manner using management practices that will minimize potential impacts, (2) occur with an emphasis on sustainability, and (3) benefit the United States while taking into account concerns of the affected states and communities. To support this declaration of policy, Congress directed the Secretary of the Interior to undertake a series of steps, several of which are directly related to the development of a commercial leasing program for oil shale and tar sands. One of these steps was the completion of a programmatic environmental impact statement (PEIS) to analyze the impacts of a commercial leasing program for oil shale and tar sands resources on public lands, with an emphasis on the most geologically prospective lands in Colorado, Utah, and Wyoming. For oil shale, the scope of the PEIS analysis includes public lands within the Green River, Washakie, Uinta, and Piceance Creek Basins. For tar sands, the scope includes Special Tar Sand Areas (STSAs) located in Utah. This paleontological resources overview report was prepared in support of the Oil Shale and Tar Sands Resource Management Plan Amendments to Address Land Use Allocations in Colorado, Utah, and Wyoming and PEIS, and it is intended to be used by Bureau of Land Management (BLM) regional paleontologists and field office staff to support future

Biomass Gasifier ''Tars'': Their Nature, Formation, and Conversion

Energy Technology Data Exchange (ETDEWEB)

Milne, T. A.; Evans, R. J. (National Renewable Energy Laboratory); Abatzaglou, N. (Kemestrie, Inc.)

1998-11-01

The main purpose of this review is to update the information on gasification tar, the most cumbersome and problematic parameter in any gasification commercialization effort. The work aims to present to the community the scientific and practical aspects of tar formation and conversion (removal) during gasification as a function of the various technological and technical parameters and variables.

Dual vapor extraction on acidic sludge tar at a former refinery

International Nuclear Information System (INIS)

Lear, P.R.; Beall, P.; Townsend, S.

1996-01-01

OHM Remediation Services Corp conducted a pilot-scale demonstration for a novel application of dual vapor extraction technology for the pretreatment of the acid tar sludge material. The acid tar sludge comprised of approximately 60% asphaltene hydrocarbon material, 20% clay, and up to 20% sulfuric acid (H 2 SO 4 ). The liquid layer in the bottom of the pits has a low pH ( 2 ) gas which is released with the sludge material is excavated or handled. The objective of the dual vapor extraction was to remove the SO 2 vapors and liquid layer containing sulfuric acid prior to any further treatment. The dual vapor extraction would reduce the amount of alkaline reagent required for neutralization while eliminating the health and safety concerns. Overall, the DVE pilot demonstration successfully showed that both liquids and vapors could be removed from the acid tar sludge material. The liquid present in the lower portions of the pits will have pH values of 1.0 or less and acidities on the order of 5% H 2 SO 4 . The liquid removed from the acid tar sludge material by a DVE system will have slightly higher pH (∼1.5) and lower alkalinities (∼3% H 2 SO 4 ). The SO 2 concentration in the vapors removed by the DVE system will be variable with initial levels approaching 1,200 ppmv SO 2 . The SO 2 concentration in the vapor phase should decrease with time. A caustic scrubber solution will remove any SO 2 from the vapor phase. After DVE treatment, the acid tar sludge material would have a slightly increased pH and a decreased SO 2 concentration

Toxicity of coal-tar and asphalt sealants to eastern newts, Notophthalmus viridescens

Energy Technology Data Exchange (ETDEWEB)

Bommarito, T.; Sparling, D.W.; Halbrook, R.S. [South Illinois University, Carbondale, IL (United States). Cooperative Wildlife Research Laboratory

2010-09-15

Between 1970 and 2000 the concentration of total polycyclic aromatic hydrocarbons (TPAH) in several lakes across the country increased whereas those of other persistent organic pollutants (POPs) tended to remain stable or declined. Urbanized watersheds experienced greater rises in TPAH concentration compared to non-urban lakes. Sources for urban PAHs include industrial wastes, vehicular exhausts and oil leaks and sealants from pavement surfaces. Both coal-tar and asphalt sealants are used to protect surfaces but runoff from surfaces coated with coal-tar can have mean concentrations of 3500 mg TPAHs kg{sup -1}, much higher than runoff from asphalt-sealed or cement surfaces. Unaltered parent compounds of PAHs can have many lethal and sublethal toxic effects, but oxidation and UV radiation can alter the toxicity of these compounds, sometimes creating degradates that are many times more toxic than parent compounds. The purposes of this study were to determine if coal-tar sealants can be toxic to adult eastern newts (Notophthalmus viridescens) and to compare the toxicity of coal-tar sealant to that of asphalt sealant. Newts were exposed to sediments containing dried sealants ranging from 0 mg kg{sup -1} to 1500 mg kg{sup -1} under simultaneous exposure to UV radiation and visible light to determine concentration/response relationships. No significant mortality occurred with any treatment. Significant effects due to sealants included decreased righting ability and diminished liver enzyme activities. Coal-tar sealant was more effective in inducing these changes than was asphalt sealant.

Tar analysis from biomass gasification by means of online fluorescence spectroscopy

Science.gov (United States)

Baumhakl, Christoph; Karellas, Sotirios

2011-07-01

Optical methods in gas analysis are very valuable mainly due to their non-intrusive character. That gives the possibility to use them for in-situ or online measurements with only optical intervention in the measurement volume. In processes like the gasification of biomass, it is of high importance to monitor the gas quality in order to use the product gas in proper machines for energy production following the restrictions in the gas composition but also improving its quality, which leads to high efficient systems. One of the main problems in the biomass gasification process is the formation of tars. These higher hydrocarbons can lead to problems in the operation of the energy system. Up to date, the state of the art method used widely for the determination of tars is a standardized offline measurement system, the so-called "Tar Protocol". The aim of this work is to describe an innovative, online, optical method for determining the tar content of the product gas by means of fluorescence spectroscopy. This method uses optical sources and detectors that can be found in the market at low cost and therefore it is very attractive, especially for industrial applications where cost efficiency followed by medium to high precision are of high importance.

Tar ball concentrations in the ocean around the Cape of Good Hope before and after a major oil spill

Energy Technology Data Exchange (ETDEWEB)

Eagle, G A; Green, A; Williams, J

1979-11-01

From August 1977 to August 1978, tar ball concentrations around the southwestern coast of South Africa were sampled. Prior to a tanker collision on December 16, 1977, the area was relatively free of floating tar. Following the collision, tar ball concentrations increased; tar was transported by wind and currents, at average speeds of about 1 km/hr. In areas of slack currents, tar was observed for as long as 8 months after the spill. Results provided information about surface current trends.

Skin cancer in patients with psoriasis treated with coal tar. A 25-year follow-up study

International Nuclear Information System (INIS)

Pittelkow, M.R.; Perry, H.O.; Muller, S.A.; Maughan, W.Z.; O'Brien, P.C.

1981-01-01

For many years, crude coal tar has been used for the treatment of psoriasis. The possible carcinogenic effect of crude coal tar and ultraviolet (UV) radiation (Goeckerman regimen), considered individually or in combination, has been of some concern to physicians. A 25-year follow-up study was completed on 280 patients with psoriasis who were hospitalized and treated with crude coal tar and UV radiation at the Mayo Clinic, Rochester, Minn, during the years 1950 through 1954. The results of this study suggest that the incidence of skin cancer is not appreciably increased above the expected incidence for the general population when patients are treated with coal tar ointments. It seems that the Goeckerman regimen (topical crude coal tar combined with UV radiation) can be used with minimal risk for skin cancer in the treatment of psoriasis

Volatilization of polycyclic aromatic hydrocarbons from coal-tar-sealed pavement

Science.gov (United States)

Van Metre, Peter C.; Majewski, Michael S.; Mahler, Barbara J.; Foreman, William T.; Braun, Christopher L.; Wilson, Jennifer T.; Burbank, Teresa L.

2012-01-01

Coal-tar-based pavement sealants, a major source of PAHs to urban water bodies, are a potential source of volatile PAHs to the atmosphere. An initial assessment of volatilization of PAHs from coal-tar-sealed pavement is presented here in which we measured summertime gas-phase PAH concentrations 0.03 m and 1.28 m above the pavement surface of seven sealed (six with coal-tar-based sealant and one with asphalt-based sealant) and three unsealed (two asphalt and one concrete) parking lots in central Texas. PAHs also were measured in parking lot dust. The geometric mean concentration of the sum of eight frequently detected PAHs (ΣPAH8) in the 0.03-m samples above sealed lots (1320 ng m-3) during the hottest part of the day was 20 times greater than that above unsealed lots (66.5 ng m-3). The geometric mean concentration in the 1.28-m samples above sealed lots (138 ng m-3) was five times greater than above unsealed lots (26.0 ng m-3). Estimated PAH flux from the sealed lots was 60 times greater than that from unsealed lots (geometric means of 88 and 1.4 μg m-2 h-1, respectively). Although the data set presented here is small, the much higher estimated fluxes from sealed pavement than from unsealed pavement indicate that coal-tar-based sealants are emitting PAHs to urban air at high rates compared to other paved surfaces.

Detailed grouping and functional composition of neutral substances in low-temperature tar

Energy Technology Data Exchange (ETDEWEB)

Kalechits, I V; Salimgareeva, F G; Popova, N I; Kurbangaleeva, D K; Klykova, G G

1955-01-01

The grouping and the functional composition of the neutral substances in coal tar were characterized by means of adsorption on silica gel with subsequent chemical analysis of each fraction. The neutral materials were obtained by consecutive treatment of a C/sub 6/H/sub 6/ solution of coal tar with 10 percent alkali and 5 percent H/sub 2/SO/sub 4/ to remove the phenols and the bases. The data show that of the neutral substances (only 75% were identified) 40.5% were aromatic hydrocarbons. Based on a study of all of the data, it was proposed that 90% of the composition of coal tars is aromatic. The physical constants of the separated fractions were determined and are presented in tabular form.

Research and information needs for management of tar sands development. Interim report Apr-May 83

Energy Technology Data Exchange (ETDEWEB)

1983-05-01

The report discusses important research and information needs for federal lease management of lands with tar sands resources. Short-term needs include more complete definition and characterization of deposits, hydrology, and regions downwind from tar sands areas. Longer-term needs include demonstration-scale operations to resolve production, waste management, and reclamation problems and to provide opportunities for measurement, analysis, and assessment of mining and processing wastes and emissions. Most of the known federal tar sands resource is in eastern Utah and contains about 25 billion barrels of bitumen. Recent legislation provides that existing mining claims and oil and gas leases may be converted to combined hydrocarbon leases including tar sands. Federal approval, which must be applied for by November 1983, is a condition for conversion.

Investigation of sulfur-polycyclic aromatic hydrocarbon in coal derived tars of pyrolysis and hydropyrolysis

Energy Technology Data Exchange (ETDEWEB)

Chen, H.; Li, B.; Zhang, B. [Chinese Academy of Sciences, Taiyuan (China). State Key Laboratory of Coal Conversion

1999-07-01

A study was undertaken to characterize sulphur forms in coal derived tars from pyrolysis and hydropyrolysis of bituminous coal and lignite. The pyrolysis tars were analyzed for content of polycyclic aromatic sulfur hydrocarbons (PASH). 5 refs., 3 figs., 3 tabs.

Crystallization and preliminary X-ray diffraction analysis of the periplasmic domain of the Escherichia coli aspartate receptor Tar and its complex with aspartate

Energy Technology Data Exchange (ETDEWEB)

Mise, Takeshi; Matsunami, Hideyuki; Samatey, Fadel A.; Maruyama, Ichiro N., E-mail: ichi@oist.jp [Okinawa Institute of Science and Technology Graduate University, 1919-1 Tancha, Onna-son, Kunigami, Okinawa 904-0495 (Japan)

2014-08-27

The periplasmic domain of the E. coli aspartate receptor Tar was cloned, expressed, purified and crystallized with and without bound ligand. The crystals obtained diffracted to resolutions of 1.58 and 1.95 Å, respectively. The cell-surface receptor Tar mediates bacterial chemotaxis toward an attractant, aspartate (Asp), and away from a repellent, Ni{sup 2+}. To understand the molecular mechanisms underlying the induction of Tar activity by its ligands, the Escherichia coli Tar periplasmic domain with and without bound aspartate (Asp-Tar and apo-Tar, respectively) were each crystallized in two different forms. Using ammonium sulfate as a precipitant, crystals of apo-Tar1 and Asp-Tar1 were grown and diffracted to resolutions of 2.10 and 2.40 Å, respectively. Alternatively, using sodium chloride as a precipitant, crystals of apo-Tar2 and Asp-Tar2 were grown and diffracted to resolutions of 1.95 and 1.58 Å, respectively. Crystals of apo-Tar1 and Asp-Tar1 adopted space group P4{sub 1}2{sub 1}2, while those of apo-Tar2 and Asp-Tar2 adopted space groups P2{sub 1}2{sub 1}2{sub 1} and C2, respectively.

The role of char and tar in determining the gas-phase partitioning of nitrogen during biomass gasification

International Nuclear Information System (INIS)

Broer, Karl M.; Brown, Robert C.

2015-01-01

Highlights: • Switchgrass was gasified at an equivalence ratio of zero and 650–850 °C. • Short residence times were employed to minimize secondary reactions. • Char- and tar-bound nitrogen, NH_3, HCN, and N_2 were all significant products. • Increasing temperature leads to increased release of gaseous nitrogen compounds. • Kinetic models of gasification should include nitrogen release from char and tar. - Abstract: Gasification is an attractive option for converting biomass into fuels and chemicals. Most biomass contains significant amounts of fuel-bound nitrogen (FBN), which partially converts into ammonia (NH_3) and hydrogen cyanide (HCN) during gasification. These nitrogen compounds are problematic as they can lead to NO_X emissions or catalyst poisoning in downstream applications of syngas. FBN can convert to other products as well, including diatomic nitrogen (N_2), char-bound nitrogen (char-N), and tar-bound nitrogen (tar-N). Efforts to predict concentrations of NH_3 and HCN have been hindered by a lack of accurate, comprehensive measurements of nitrogen partitioning among gasification products. The present study gasified switchgrass under allothermal, short residence time conditions and measured NH_3, HCN, char-N, and tar-N as a function of temperature in the range of 650–850 °C with diatomic nitrogen determined by difference. It was found that a major portion of FBN was retained in the char and tar products. As temperature was increased, char and tar were consumed, releasing nitrogen as gaseous NH_3 and HCN. This increase in undesirable nitrogen compounds is contrary to the predictions of most gasification models, which overlook the presence of significant nitrogen in char and tar even if they include tar cracking and char gasification reactions. The results of this study demonstrate that gas-phase reactions alone are not sufficient to predict the fate of nitrogen during gasification. In order for modeling efforts to obtain more accurate

Potential contributions of asphalt and coal tar to black carbon quantification in urban dust, soils, and sediments

Energy Technology Data Exchange (ETDEWEB)

Yang, Y.; Mahler, B.J.; Van Metre, P.C.; Ligouis, B.; Werth, C.J. [University of Illinois Urbana Champaign, Urbana, IL (USA). Dept. of Civil & Environmental Engineering

2010-12-01

Measurements of black carbon (BC) using either chemical or thermal oxidation methods are generally thought to indicate the amount of char and/or soot present in a sample. In urban environments, however, asphalt and coal-tar particles worn from pavement are ubiquitous and, because of their pyrogenic origin, could contribute to measurements of BC. Here we explored the effect of the presence of asphalt and coal-tar particles on the quantification of BC in a range of urban environmental sample types, and evaluated biases in the different methods used for quantifying BC. Samples evaluated were pavement dust, residential and commercial area soils, lake sediments from a small urban watershed, and reference materials of asphalt and coal tar. Total BC was quantified using chemical treatment through acid dichromate (Cr{sub 2}O{sub 7}) oxidation and chemo-thermal oxidation at 375{sup o}C (CTO-375). BC species, including soot and char/charcoal, asphalt, and coal tar, were quantified with organic petrographic analysis. Comparison of results by the two oxidation methods and organic petrography indicates that both coal tar and asphalt contribute to BC quantified by Cr{sub 2}O{sub 7} oxidation, and that coal tar contributes to BC quantified by CTO-375. These results are supported by treatment of asphalt and coal-tar reference samples with Cr2O7 oxidation and CTO-375. The reference asphalt is resistant to Cr{sub 2}O{sub 7} oxidation but not to CTO-375, and the reference coal tar is resistant to both Cr2O7 oxidation and CTO-375. These results indicate that coal tar and/or asphalt can contribute to BC measurements in samples from urban areas using Cr{sub 2}O{sub 7} oxidation or CTO-375, and caution is advised when interpreting BC measurements made with these methods.

Volatilization of polycyclic aromatic hydrocarbons from coal-tar-sealed pavement.

Science.gov (United States)

Van Metre, Peter C; Majewski, Michael S; Mahler, Barbara J; Foreman, William T; Braun, Christopher L; Wilson, Jennifer T; Burbank, Teresa L

2012-06-01

Coal-tar-based pavement sealants, a major source of PAHs to urban water bodies, are a potential source of volatile PAHs to the atmosphere. An initial assessment of volatilization of PAHs from coal-tar-sealed pavement is presented here in which we measured summertime gas-phase PAH concentrations 0.03 m and 1.28 m above the pavement surface of seven sealed (six with coal-tar-based sealant and one with asphalt-based sealant) and three unsealed (two asphalt and one concrete) parking lots in central Texas. PAHs also were measured in parking lot dust. The geometric mean concentration of the sum of eight frequently detected PAHs (ΣPAH(8)) in the 0.03-m samples above sealed lots (1320 ng m(-3)) during the hottest part of the day was 20 times greater than that above unsealed lots (66.5 ng m(-3)). The geometric mean concentration in the 1.28-m samples above sealed lots (138 ng m(-3)) was five times greater than above unsealed lots (26.0 ng m(-3)). Estimated PAH flux from the sealed lots was 60 times greater than that from unsealed lots (geometric means of 88 and 1.4 μg m(-2) h(-1), respectively). Although the data set presented here is small, the much higher estimated fluxes from sealed pavement than from unsealed pavement indicate that coal-tar-based sealants are emitting PAHs to urban air at high rates compared to other paved surfaces. Published by Elsevier Ltd.

UTILIZATION OF ACTIVATED ZEOLITE AS MOLECULAR SIEVE IN CHROMATOGRAPHIC COLUMN FOR SEPARATION OF COAL TAR COMPOUNDS

Directory of Open Access Journals (Sweden)

Dwi Retno Nurotul Wahidiyah

2010-06-01

Full Text Available Application of activated zeolite (ZAA as molecular sieve to separate compounds of coal tar from vaccum fractional distillation, have been done. The size of zeolite was 10-20 mesh and used as solid phase in column chromatography with length of 30 cm. The first step of the research was coal pyrolisis and the product (tar was distillated by fractional column and vaccum system at reduced pressure 44 cmHg and maximum temperature at 200 oC. The distillate from this procedure was flowed to the column chromatography of zeolite (ZAA. The compound absorbed by zeolite was eluted with varying solvents, i.e: CCl4, acetone and ethanol. Each fraction was then analyzed by gas chromatography. The results showed, zeolite have a capability to separate the compounds of tar and it tends to absorb medium hydrocarbon. The nonpolar eluent [CCl4] gives the better result in eluting tar compound than polar (ethanol or medium polar eluents (acetone.   Keywords: zeolite, coal tar, column chromatography

Development of secondary chamber for tar cracking-improvement of wood pyrolysis performance in pre-vacuum chamber

Science.gov (United States)

Siahaan, S.; Homma, H.; Homma, H.

2018-02-01

Energy crisis and global warming, in other words, climate change are critical topics discussed in various parts of the world. Global warming primarily result from too much emission of carbon dioxide (CO2) in the atmosphere. To mitigate global warming, or climate change and improve electrification in rural areas, wood pyrolysis technology is developed in a laboratory scale, of which gases are directly applicable to the gas engine generator. Our laboratory has developed a prototype of wood pyrolysis plant with a pre-vacuum chamber. However, tar yield was around 40 wt% of feedstock. This research aims to reduce tar yield by secondary tar cracking. For the secondary tar cracking, a secondary pre-vacuum chamber is installed after primary pre-vacuum chamber. Gases generated in the primary pre-vacuum chamber are lead into the secondary chamber that is heated up to 1000 K. This paper reports performance of the secondary chamber for secondary tar cracking in homogeneous mode and heterogeneous mode with char.

IDENTIFICATION OF SOME CARCINOGENIC POLYCYCLIC AROMATIC HYDROCARBONS IN BANGLADESHI VEHICLES EXHAUST TAR BY GAS CHROMATOGRAPHY-MASS SPECTROPHOTOMETER

Directory of Open Access Journals (Sweden)

M. Amzad Hossain

2010-06-01

Full Text Available A more sensitive GC-MS method has been established for the determination of some carcinogenic polycyclic aromatic hydrocarbons (PAHs in vehicles exhaust tar samples. The tar samples were extracted using dichloromethane (DMC: n-hexane solvent mixture. A multi-layer clean-up (silica gel/sodium sulphate column was used, followed by glass fiber filter (GFF paper. The method was successfully applied to determine a number of PAHs present in exhaust tar sample of different vehicles of the Atomic Energy Centre, Dhaka, Bangladesh.   Keywords: Carcinogenic polycyclic aromatic hydrocarbons, vehicles tar samples, identification, GC-MS/MS

Coal-tar based pavement sealant toxicity to freshwater macroinvertebrates.

Science.gov (United States)

Bryer, Pamela J; Scoggins, Mateo; McClintock, Nancy L

2010-05-01

Non-point-source pollution is a major source of ecological impairment in urban stream systems. Recent work suggests that coal-tar pavement sealants, used extensively to protect parking areas, may be contributing a large portion of the polycyclic aromatic hydrocarbon (PAH) loading seen in urban stream sediments. The hypothesis that dried coal-tar pavement sealant flake could alter the macroinvertebrate communities native to streams in Austin, TX was tested using a controlled outdoor laboratory type approach. The treatment groups were: control, low, medium, and high with total PAH concentrations (TPAH = sum of 16 EPA priority pollutant PAHs) of 0.1, 7.5, 18.4, & 300 mg/kg respectively. The low, medium, and high treatments were created via the addition of dried coal-tar pavement sealant to a sterile soil. At the start of the 24-day exposure, sediment from a minimally impacted local reference site containing a community of live sediment-dwelling benthic macroinvertebrates was added to each replicate. An exposure-dependent response was found for several stream health measures and for several individual taxa. There were community differences in abundance (P = 0.0004) and richness (P pavement sealants contain bioavailable PAHs that may harm aquatic environments. Copyright 2009 Elsevier Ltd. All rights reserved.

Solvent extraction of Southern US tar sands

Energy Technology Data Exchange (ETDEWEB)

Penney, W.R.

1990-01-01

The Department of Chemical Engineering at the University of Arkansas, in association with Diversified Petroleum Recovery, Inc. (DPR) of Little Rock, Arkansas, has been developing a solvent extraction process for the recovery of bitumen from tar sands for the past five years. The unique feature of the process is that the bitumen is recovered from the solvent by contacting with a co-solvent, which causes the bitumen to precipitate. The overall purpose of this project is to study both the technical and economic feasibility of applying this technology for recovery of bitumen from tar sands by (1) investigating the socioeconmic factors which affect (a) plant siting and (b) the market value of recovered bitumen; (2) operating a process demonstration unit at the rate of 1 lb/hr recovered bitumen while producing clean sand and recyclable solvents; and (3) determine the economic conditions which will make a bitumen recovery project economical. DPR has analyzed the historical trends of domestic production, consumption, discoveries and reserves of crude oil. They have started an investigation of the volatility in the price of crude oil and of gasoline prices and of the differential between gasoline and crude oil. DPR continues to analyze the geographical movement and demand for asphalt products. Utah does not appear economically attractive as a site for a bitumen from tar sands asphalt plant. Oklahoma sites are now being studied. This report also contains the quarterly progress report from a University of Nevada study to determine bitumen composition, oxygen uptake rates, and viscosities of Alabama and Utah bitumens. Both reports have been indexed separately for inclusion on the data base.

Pelagic tar, dissolved/dispersed petroleum hydrocarbons and plastic distribution in the Cretan Sea, Greece

Energy Technology Data Exchange (ETDEWEB)

Kornilios, S.; Drakopoulos, P.G.; Dounas, C. [Institute of Marine Biology of Crete, Iraklio (Greece). Environmental Dept.

1998-12-01

During the first cruise of R/V `Philia` in July 1997 within the framework of the TALOS programme supported by the Greek Ministry of Physical Planning and Public Works, the sampling of floating tar, litter and sea water for dissolved/dispersed petroleum hydrocarbons (DDPH) was carried out in the Cretan Sea. Analysis of these data has allowed a first assessment of the status of floating marine pollution in the region. DDPH measurements showed a mean concentration of 0.145 {mu}g/l of chrysene equivalents (n = 24). Tar and plastics concentrations were in the range of 1-4280 and 0-1160 {mu}g/m{sup 2}, respectively. Mean pelagic tar concentration was 318 {mu}g/m{sup 2}, more than two times higher than what was reported for the area in previous studies. Based on in situ hydrographic observations there is strong evidence that most of the floating tar enters the Cretan Sea through the Ionian Sea. (author)

Pelagic tar, dissolved/dispersed petroleum hydrocarbons and plastic distribution in the Cretan Sea, Greece

Energy Technology Data Exchange (ETDEWEB)

Kornilios, S.; Drakopoulos, P.G.; Dounas, C. [Institute of Marine Biology of Crete, Iraklio (Greece). Environmental Dept.

1998-12-01

During the first cruise of R/V 'Philia' in July 1997 within the framework of the TALOS programme supported by the Greek Ministry of Physical Planning and Public Works, the sampling of floating tar, litter and sea water for dissolved/dispersed petroleum hydrocarbons (DDPH) was carried out in the Cretan Sea. Analysis of these data has allowed a first assessment of the status of floating marine pollution in the region. DDPH measurements showed a mean concentration of 0.145 {mu}g/l of chrysene equivalents (n = 24). Tar and plastics concentrations were in the range of 1-4280 and 0-1160 {mu}g/m{sup 2}, respectively. Mean pelagic tar concentration was 318 {mu}g/m{sup 2}, more than two times higher than what was reported for the area in previous studies. Based on in situ hydrographic observations there is strong evidence that most of the floating tar enters the Cretan Sea through the Ionian Sea. (author)

Pelagic tar, dissolved/dispersed petroleum hydrocarbons and plastic distribution in the Cretan Sea, Greece

International Nuclear Information System (INIS)

Kornilios, S.; Drakopoulos, P.G.; Dounas, C.

1998-01-01

During the first cruise of R/V 'Philia' in July 1997 within the framework of the TALOS programme supported by the Greek Ministry of Physical Planning and Public Works, the sampling of floating tar, litter and sea water for dissolved/dispersed petroleum hydrocarbons (DDPH) was carried out in the Cretan Sea. Analysis of these data has allowed a first assessment of the status of floating marine pollution in the region. DDPH measurements showed a mean concentration of 0.145 μg/l of chrysene equivalents (n = 24). Tar and plastics concentrations were in the range of 1-4280 and 0-1160 μg/m 2 , respectively. Mean pelagic tar concentration was 318 μg/m 2 , more than two times higher than what was reported for the area in previous studies. Based on in situ hydrographic observations there is strong evidence that most of the floating tar enters the Cretan Sea through the Ionian Sea. (author)

77 FR 48431 - Safety Zone for Fireworks Display, Pamlico and Tar Rivers; Washington, NC

Science.gov (United States)

2012-08-14

... near the Pamlico and Tar Rivers to commemorate Beaufort County's 300th anniversary. The temporary... 1625-AA00 Safety Zone for Fireworks Display, Pamlico and Tar Rivers; Washington, NC AGENCY: Coast Guard, DHS. ACTION: Temporary final rule. SUMMARY: The Coast Guard is establishing a temporary safety zone on...

The extraction of bitumen from western tar sands. Annual report, July 1990--July 1991

Energy Technology Data Exchange (ETDEWEB)

Oblad, A.G.; Bunger, J.W.; Deo, M.D.; Hanson, F.V.; Miller, J.D.; Seader, J.D.

1992-04-01

Contents of this report include the following: executive summary; characterization of the native bitumen from the Whiterocks oil sand deposit; influence of carboxylic acid content on bitumen viscosity; water based oil sand separation technology; extraction of bitumen from western oil sands by an energy-efficient thermal method; large- diameter fluidized bed reactor studies; rotary kiln pyrolysis of oil sand; catalytic upgrading of bitumen and bitumen derived liquids; ebullieted bed hydrotreating and hydrocracking; super critical fluid extraction; bitumen upgrading; 232 references; Appendix A--Whiterocks tar sand deposit bibliography; Appendix B--Asphalt Ridge tar sand deposit bibliography; and Appendix C--University of Utah tar sands bibliography.

Selected constituents in the smokes of U. S. commercial cigaretts: tar, nicotine, carbon monoxide and carbon dioxide

Energy Technology Data Exchange (ETDEWEB)

Jenkins, R.A.; Quincy, R.B.; Guerin, M.R.

1979-05-01

One hundred twenty-one brands of United States commercial cigarettes were analyzed for their deliveries of tar, nicotine, carbon monoxide, and carbon dioxide under standard analytical smoking conditions. The sample included both filter and nonfilter cigarettes. Comparisons of carbon monoxide deliveries over the range of observed tar deliveries indicated a very high correlation between CO and tar for filter cigarettes, but nonfilter cigarettes tended to produce much less CO than would have been predicted from their tar deliveries. Comparison of ORNL nicotine values for specific brands with those determined by the Federal Trade Commission yield no statistically significant differences between laboratories. 4 figures, 6 tables.

Some studies on tar pillets at Veraval coast (Gujarat)

Digital Repository Service at National Institute of Oceanography (India)

Kadam, A.N.

Infrared spectroscopic (IR) analysis indicated that the tar pillets contain saturated hydrocarbons particularly higher homologues of n-paraffins, unsaturated and carbonyl type of polar compounds. Gas chromatographic (GLC) fingerprint pattern...

Hydrogen production from biomass tar by catalytic steam reforming

International Nuclear Information System (INIS)

Yoon, Sang Jun; Choi, Young-Chan; Lee, Jae-Goo

2010-01-01

The catalytic steam reforming of model biomass tar, toluene being a major component, was performed at various conditions of temperature, steam injection rate, catalyst size, and space time. Two kinds of nickel-based commercial catalyst, the Katalco 46-3Q and the Katalco 46-6Q, were evaluated and compared with dolomite catalyst. Production of hydrogen generally increased with reaction temperature, steam injection rate and space time and decreased with catalyst size. In particular, zirconia-promoted nickel-based catalyst, Katalco 46-6Q, showed a higher tar conversion efficiency and shows 100% conversion even relatively lower temperature conditions of 600 deg. C. Apparent activation energy was estimated to 94 and 57 kJ/mol for dolomite and nickel-based catalyst respectively.

Luminescence monitoring of oil or tar contamination for industrial hygiene

International Nuclear Information System (INIS)

Gammage, R.B.; Vo-Dinh, T.

1980-01-01

Synfuel plants produce potentially carcinogenic oils and tars. Exposure of workers to these tars and oils is difficult to avoid completely and occurs via direct contact with dirty surfaces or condensation of escaped fumes onto or within the body. Surface skin, measurements are made directly with a near-ultraviolet luminoscope employing a fiber optics lightguide and a stethoscopic cap pressed against the skin. This instrument is especially suitable for measuring ng to μg/cm 2 amounts of residual contamination remaining on the surface of the skin after washing. To minimize the potential for carcinogenicity, the excitating ultraviolet light intensity is only 1/100th that of sunlight. (orig.)

Heavy crude and tar sands - the long-term oil reserve

Energy Technology Data Exchange (ETDEWEB)

Barnea, J

1984-10-01

It appears that heavy crude and tar sands occur in many sedimentary areas, and estimates of known world-wide quantities exceed those known for conventional light crude resources. Although there are not precise figures available, production could be as high as three million barrels per day, with Venezuela, the US, and Canada the largest producers. There are different scales to measure the costs of production because of differences in the quality of various types of heavy crude and tar sands. Economic development of these resources should banish fears of oil scarcity in the foreseeable future. A center for information exchange through international meetings and publications is under development.

Effects of electric current upon catalytic steam reforming of biomass gasification tar model compounds to syngas

International Nuclear Information System (INIS)

Tao, Jun; Lu, Qiang; Dong, Changqing; Du, Xiaoze; Dahlquist, Erik

2015-01-01

Highlights: • ECR technique was proposed to convert biomass gasification tar model compounds. • Electric current enhanced the reforming efficiency remarkably. • The highest toluene conversion reached 99.9%. • Ni–CeO 2 /γ-Al 2 O 3 exhibited good stability during the ECR performance. - Abstract: Electrochemical catalytic reforming (ECR) technique, known as electric current enhanced catalytic reforming technique, was proposed to convert the biomass gasification tar into syngas. In this study, Ni–CeO 2 /γ-Al 2 O 3 catalyst was prepared, and toluene was employed as the major feedstock for ECR experiments using a fixed-bed lab-scale setup where thermal electrons could be generated and provided to the catalyst. Several factors, including the electric current intensity, reaction temperature and steam/carbon (S/C) ratio, were investigated to reveal their effects on the conversion of toluene as well as the composition of the gas products. Moreover, toluene, two other tar model compounds (benzene and 1-methylnaphthalene) and real tar (tar-containing wastewater) were subjected to the long period catalytic stability tests. All the used catalysts were analyzed to determine their carbon contents. The results indicated that the presence of electric current enhanced the catalytic performance remarkably. The toluene conversion reached 99.9% under the electric current of 4 A, catalytic temperature of 800 °C and S/C ratio of 3. Stable conversion performances of benzene, 1-methylnaphthalene and tar-containing wastewater were also observed in the ECR process. H 2 and CO were the major gas products, while CO 2 and CH 4 were the minor ones. Due to the promising capability, the ECR technique deserves further investigation and application for efficient tar conversion

Pyrolysis kinetics of phenols from lignite semicoking tar

Energy Technology Data Exchange (ETDEWEB)

Platonov, V.V.; Polovetskaya, O.S.; Proskuryakov, V.A.; Shavyrina, O.A. [Leo Tolstoy Tula State Pedag University, Tula (Russian Federation)

2002-11-01

The features of pyrolysis of phenols from lignite semicoking tar were studied. The activation energy and order of the reactions of accumulation of methane, hydrogen, carbon monoxide and dioxide, naphthalene and its methyl homologs, phenols, and isomeric cresols and dimethylphenols were determined.

Pyrolysis of aseptic packages (tetrapak) in a laboratory screw type reactor and secondary thermal/catalytic tar decomposition

Energy Technology Data Exchange (ETDEWEB)

Haydary, J., E-mail: juma.haydary@stuba.sk [Institute of Chemical and Environmental Engineering, Faculty of Chemical and Food Technology, Slovak University of Technology, Radlinského 9, 812 37 Bratislava (Slovakia); Susa, D.; Dudáš, J. [Institute of Chemical and Environmental Engineering, Faculty of Chemical and Food Technology, Slovak University of Technology, Radlinského 9, 812 37 Bratislava (Slovakia)

2013-05-15

Highlights: ► Pyrolysis of aseptic packages was carried out in a laboratory flow reactor. ► Distribution of tetrapak into the product yields was obtained. ► Composition of the pyrolysis products was estimated. ► Secondary thermal and catalytic decomposition of tars was studied. ► Two types of catalysts (dolomite and red clay marked AFRC) were used. - Abstract: Pyrolysis of aseptic packages (tetrapak cartons) in a laboratory apparatus using a flow screw type reactor and a secondary catalytic reactor for tar cracking was studied. The pyrolysis experiments were realized at temperatures ranging from 650 °C to 850 °C aimed at maximizing of the amount of the gas product and reducing its tar content. Distribution of tetrapak into the product yields at different conditions was obtained. The presence of H{sub 2}, CO, CH{sub 4}, CO{sub 2} and light hydrocarbons, HCx, in the gas product was observed. The Aluminum foil was easily separated from the solid product. The rest part of char was characterized by proximate and elemental analysis and calorimetric measurements. The total organic carbon in the tar product was estimated by elemental analysis of tars. Two types of catalysts (dolomite and red clay marked AFRC) were used for catalytic thermal tar decomposition. Three series of experiments (without catalyst in a secondary cracking reactor, with dolomite and with AFRC) at temperatures of 650, 700, 750, 800 and 850 °C were carried out. Both types of catalysts have significantly affected the content of tars and other components in pyrolytic gases. The effect of catalyst on the tetrapack distribution into the product yield on the composition of gas and on the total organic carbon in the tar product is presented in this work.

Machine-smoking studies of cigarette filter color to estimate tar yield by visual assessment and through the use of a colorimeter.

Science.gov (United States)

Morton, Michael J; Williams, David L; Hjorth, Heather B; Smith, Jennifer H

2010-04-01

This paper explores using the intensity of the stain on the end of the filter ("filter color") as a vehicle for estimating cigarette tar yield, both by instrument reading of the filter color and by visual comparison to a template. The correlation of machine-measured tar yield to filter color measured with a colorimeter was reasonably strong and was relatively unaffected by different puff volumes or different tobacco moistures. However, the correlation of filter color to machine-measured nicotine yield was affected by the moisture content of the cigarette. Filter color, as measured by a colorimeter, was generally comparable to filter extraction of either nicotine or solanesol in its correlation to machine-smoked tar yields. It was found that the color of the tar stain changes over time. Panelists could generally correctly order the filters from machine-smoked cigarettes by tar yield using the intensity of the tar stain. However, there was considerable variation in the panelist-to-panelist tar yield estimates. The wide person-to-person variation in tar yield estimates, and other factors discussed in the text could severely limit the usefulness and practicality of this approach for visually estimating the tar yield of machine-smoked cigarettes. Copyright 2009 Elsevier Inc. All rights reserved.

Fungal cultures of tar bush and creosote bush for production of two phenolic antioxidants (pyrocatechol and gallic acid).

Science.gov (United States)

Ventura, J; Gutiérrez-Sanchez, G; Rodríguez-Herrera, R; Aguilar, C N

2009-01-01

'Tar bush' and 'creosote bush' were substrates of fungal cultivation for tannase production and gallic acid and pyrocatechol accumulation. Aspergillus niger GH1 grew similarly on both plant materials under solid state culture conditions, reaching maximal levels after 4 d. Fungal strain degraded all tannin content of creosote bush after 4 d of fermentation and >75 % of tar bush after 5 d. Higher level of tannase activity was detected in tar bush fermentation. Biotransformation of tannins to gallic acid was high (93 % in creosote bush and 89 % in tar bush). Pyrocatechol was released poorly. Kinetic parameters of tannin conversion were calculated.

Family physicians and youth tobacco-free education: outcomes of the Colorado Tar Wars program.

Science.gov (United States)

Cain, Jeffrey J; Dickinson, W Perry; Fernald, Douglas; Bublitz, Caroline; Dickinson, L Miriam; West, David

2006-01-01

Tar Wars is a national school-based tobacco-free education program operated by the American Academy of Family Physicians. The Tar Wars lesson uses an interactive 45-min session taught by volunteer family physicians in 4th- and 5th-grade classrooms and focuses on the short-term image-based consequences of tobacco use. In this study, we evaluated the effectiveness of the Tar Wars program in Colorado with both quantitative and qualitative measures. Students participating in the quantitative evaluation were tested before and after a Tar Wars teaching session using a 14-question test covering the short-term and image-based consequences of tobacco use, cost of smoking, tobacco advertising, and social norms of tobacco use. Qualitative evaluation of the program included guided telephone interviews and focus groups with participating students, teachers, and presenters. Quantitative evaluation showed statistically significant improvement in correct responses for the 14 questions measured with an average increase in correct responses from 8.95 to 10.23. Three areas recommended by the Centers for Disease Control (CDC) for youth tobacco prevention showed greater change in correct responses, including cost of smoking, truth of tobacco advertising, and peer norms of tobacco use. Qualitative evaluation found that the overall message of the session was well received, that previously known tobacco information was reinforced by its presentation in a novel format, and that new information learned included cost of smoking, truth of tobacco advertising, and peer norms of tobacco use. The Tar Wars lesson plan is effective in increasing students' understanding about the short-term consequences of tobacco use, cost of tobacco use, truth of tobacco advertising, and peer norms. Tar Wars meets the CDC guidelines as one component of effective comprehensive youth tobacco prevention.

No Increased Risk of Cancer after Coal Tar Treatment in Patients with Psoriasis or Eczema

NARCIS (Netherlands)

Roelofzen, Judith H. J.; Aben, Katja K. H.; Oldenhof, Ursula T. H.; Coenraads, Pieter-Jan; Alkemade, Hans A.; van de Kerkhof, Peter C. M.; van der Valk, Pieter G. M.; Kiemeney, Lambertus A. L. M.

Coal tar is an effective treatment for psoriasis and eczema, but it contains several carcinogenic compounds. Occupational and animal studies have shown an increased risk of cancer after exposure to coal tar. Many dermatologists have abandoned this treatment for safety reasons, although the risk of

Tar removal from biomass derived fuel gas by pulsed corona discharges: chemical kinetic study II

NARCIS (Netherlands)

Nair, S.A.; Yan, K.; Pemen, A.J.M.; Heesch, van E.J.M.; Ptasinski, K.J.; Drinkenburg, A.A.H.

2005-01-01

Tar (heavy hydrocarbon or poly aromatic hydrocarbon (PAH)) removal from biomass derived fuel gas is one of the biggest obstacles in its utilization for power generation. We have investigated pulsed corona as a method for tar removal. Our previous experimental results indicate the energy consumption

Abating coal tar seepage into surface water bodies using sheet piles with sealed interlocks

International Nuclear Information System (INIS)

Collingwood, B.I.; Boscardin, M.D.; Murdock, R.F.

1995-01-01

A former coal tar processing facility processed crude coal tar supplied from manufactured gas plants in the area. Coal-tar-contaminated ground water from the site was observed seeping through an existing timber bulkhead along a tidal river and producing a multicolored sheen on the surface of the river. As part of a short-term measure to abate the seepage into the river, 64-m long anchored sheet pile wall with sheet pile wing walls at each end was constructed inland of the of the timber bulkhead. The sheet piles extended to low-permeability soils at depth and the interlocks of the sheet piles were provided with polyurethane rubber seals. Based on postconstruction observations for leakage and sheens related to leakage, the steel sheet piles with polyurethane rubber interlock seals appeared to provide a successful seal and abate coal-tar-contaminated ground water seepage into the river. The tie rod penetration sealing proved to be a more problematic detail, but through several postconstruction grouting episodes, an effective seal was produced

Effect of the rate of heating on the quality of the primary tar in low-temperature coal-carbonization process

Energy Technology Data Exchange (ETDEWEB)

Turskii, Y I

1956-01-01

Two stages are observed. The first stage yields products of the primary and partial decomposition of coal, mainly water, CO/sub 2/, and CO as decomposition products of functional groups (-COOH, > CO, - OH, and so forth). No tar is formed in this stage. The structural decomposition and tar formation occur in the second stage. The rate of heating is important for the quality of the tar obtained. The slow rate of heating with both stages following each other yields a good-quality tar, richer in C and H, with lower O content. In case of high rate of heating both stages overlap. The tar is of poorer quality with higher specific gravity, and contains more O and asphaltenes. The complete experimental data are given in detail.

BTX production by in-situ contact reforming of low-temperature tar from coal with zeolite-derived catalysts; Zeolite kei shokubai wo mochiita sekitan teion tar no sesshoku kaishitsu ni yoru BTX no seisei

Energy Technology Data Exchange (ETDEWEB)

Matsunaga, T.; Fuda, K.; Murakami, K.; Kyo, M.; Hosoya, S.; Kobayashi, S. [Akita University, Akita (Japan). Mining College

1996-10-28

On BTX production process from low-temperature tar obtained by pyrolysis of coal, the effect of exchanged metallic species and reaction temperature were studied using metallic ion-exchanged Y-zeolite as catalyst. In experiment, three kinds of coals with different produced tar structures such as Taiheiyo and PSOC-830 sub-bituminous coals and Loy Yang brown coal were used. Y-zeolite ion-exchanged with metal chloride aqueous solution was used as catalyst. Zn{sup 2+}, Ni{sup 2+} and In{sup 3+} were used as metal ions to be exchanged. The experiment was conducted by heating a pyrolysis section up to 600{degree}C for one hour after preheating a contact reforming section up to a certain proper temperature. As a result, the Ni system catalyst was effective for BTX production from aromatic-abundant tar, while the Zn system one from lower aromatic tar. In general, relatively high yields of toluene and xylene were obtained at lower temperature, while those of benzene at higher temperature. 4 figs., 1 tab.

Coliquefaction of coal, tar sand bitumen and plastic (interaction among coal, bitumen and plastic); Sekitan/tar sand bitumen/plastic no kyoekika ni okeru kyozon busshitsu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Yamaguchi, H.; Okuyama, Y.; Matsubara, K. [NKK Corp., Tokyo (Japan); Kamo, T.; Sato, Y. [National Institute for Resources and Environment, Tsukuba (Japan)

1996-10-28

For the improvement of economy, coliquefaction of coal, tar sand bitumen and plastic was performed under low hydrogen pressure, to investigate the influence of interaction among these on the liquefaction characteristics. For comparison, coliquefaction was also performed under the hydrogen pressure same as the NEDOL process. In addition, for clarifying its reaction mechanism, coliquefaction of dibenzyl and plastic was performed as a model experiment, to illustrate the distribution of products and composition of oil, and to discuss the interaction between dibenzyl and various plastics, and between various plastics. Under direct coal liquefaction conditions, coprocessing of Tanito Harum coal, Athabasca tar sand and plastic was carried out under low hydrogen pressure with an autoclave. The observed value of oil yield was higher than the calculated value based on the values from separate liquefaction of coal and plastic, which suggested the interaction between coal and the mixed plastic. The results of coliquefaction of coal, tar sand bitumen and plastic could be explained from the obtained oil yield and its composition by the coliquefaction of dibenzyl and plastic. 2 refs., 3 tabs.

Evidence for conformational flexibility in the Tat-TAR recognition motif of cyclin T1

International Nuclear Information System (INIS)

Das, Chandreyee; Edgcomb, Stephen P.; Peteranderl, Ralph; Chen, Lily; Frankel, Alan D.

2004-01-01

Cyclin T1 (CycT1) is a cellular transcription elongation factor that also participates in Tat-mediated activation of several lentiviral promoters. In human immunodeficiency virus (HIV), CycT1 is required for Tat to bind tightly to TAR and interacts in the ternary complex via its Tat-TAR recognition motif (TRM). In the related bovine immunodeficiency virus (BIV), Tat recognizes its cognate TAR element with high affinity and specificity in the absence of CycT1. At both promoters, CycT1 recruits the Cdk9 kinase, which phosphorylates RNA polymerase II to generate processive transcription complexes. To examine the physical properties of CycT1, we purified a functional domain corresponding to residues 1-272 and found that it possesses a stably folded core, as judged by partial proteolysis and circular dichroism experiments. Interestingly, the C-terminal 20 residues corresponding to the TRM appear conformationally flexible or disordered. The TRM of the bovine CycT1 (bCycT1) is similarly sensitive to proteolysis yet differs in sequence from the human protein. In particular, bCycT1 lacks a cysteine at residue 261 known to be critical for HIV but not BIV ternary complex formation, and mutagenesis data are consistent with a proposed role for this cysteine in metal binding. The apparent flexibility of the TRM suggests that conformational rearrangements may accompany formation of CycT1-Tat-TAR ternary complexes and may contribute to different TAR recognition strategies in different lentiviruses

Numerical simulation of vortex pyrolysis reactors for condensable tar production from biomass

Energy Technology Data Exchange (ETDEWEB)

Miller, R.S.; Bellan, J. [California Inst. of Tech., Pasadena, CA (United States). Jet Propulsion Lab.

1998-08-01

A numerical study is performed in order to evaluate the performance and optimal operating conditions of vortex pyrolysis reactors used for condensable tar production from biomass. A detailed mathematical model of porous biomass particle pyrolysis is coupled with a compressible Reynolds stress transport model for the turbulent reactor swirling flow. An initial evaluation of particle dimensionality effects is made through comparisons of single- (1D) and multi-dimensional particle simulations and reveals that the 1D particle model results in conservative estimates for total pyrolysis conversion times and tar collection. The observed deviations are due predominantly to geometry effects while directional effects from thermal conductivity and permeability variations are relatively small. Rapid ablative particle heating rates are attributed to a mechanical fragmentation of the biomass particles that is modeled using a critical porosity for matrix breakup. Optimal thermal conditions for tar production are observed for 900 K. Effects of biomass identity, particle size distribution, and reactor geometry and scale are discussed.

Analysis of the use of coal tar as a binder in bituminous mixtures, using Marshall and Ramcodes methodologies

International Nuclear Information System (INIS)

Ochoa-Díaz, R

2013-01-01

This paper presents an alternative use of coal tar, a by-product of the steel industry, given the problems of accumulation and negative environmental impact. Therefore, it is necessary to analyze the incorporation of coal tar as a binder in paving mixtures. First, this paper presents the origin, description of the main characteristics, and properties of tar. Then, this paper evaluates the mix of coal tar by means of the RAMCODES and Marshall methodologies to determine its resistance. The results of the tests explain the physical and mechanical properties of the mix. Taking into account the results of both methods, this paper makes a comparison to determine the suitability of the RAMCODES methodology in the mix design. Finally, it analyzes the alternatives to coal tar that can be used as binders in bituminous mixes for pavement and the advantages of their uses under some specific conditions

Quantitative analysis of phenol and alkylphenols in Brazilian coal tar

Directory of Open Access Journals (Sweden)

Elina Bastos Caramão

2004-04-01

Full Text Available The main purpose of this work is the identification and quantification of phenolic compounds in coal tar samples from a ceramics factory in Cocal (SC, Brazil. The samples were subjected to preparative scale liquid chromatography, using Amberlyst A-27TM ion-exchange resin as stationary phase. The fractions obtained were classified as "acids" and "BN" (bases and neutrals. The identification and quantification of phenols, in the acid fraction, was made by gas chromatography coupled to mass spectrometry (GC/MS. Nearly twenty-five phenols were identified in the samples and nine of them were also quantified. The results showed that coal tar has large quantities of phenolic compounds of industrial interest.

Understanding the fate and transport of petroleum hydrocarbons from coal tar within gasholders.

Science.gov (United States)

Coulon, Frédéric; Orsi, Roberto; Turner, Claire; Walton, Chris; Daly, Paddy; Pollard, Simon J T

2009-02-01

Coal tars have been identified as posing a threat to human health due to their toxic, mutagenic and carcinogenic characteristics. Workers involved in former gasholders decommissioning are potentially exposed to relevant concentrations of volatile and semi-volatile hydrocarbons upon opening up derelict tanks and during tar excavation/removal. While information on contaminated sites air-quality and its implications on medium-long term exposure is available, acute exposure issues associated with the execution of critical tasks are less understood. Calculations indicated that the concentration of a given contaminant in the gasholder vapour phase only depends on the coal tar composition, being only barely affected by the presence of water in the gasholder and the tar volume/void space ratio. Fugacity modelling suggested that risk-critical compounds such as benzene, naphthalene and other monocyclic and polycyclic aromatic hydrocarbons may gather in the gasholder air phase at significant concentrations. Gasholder emissions were measured on-site and compared with the workplace exposure limits (WELs) currently in use in UK. While levels for most of the toxic compounds were far lower than WELs, benzene air-concentrations where found to be above the accepted threshold. In addition due to the long exposure periods involved in gasholder decommissioning and the significant contribution given by naphthalene to the total coal tar vapour concentration, the adoption of a WEL for naphthalene may need to be considered to support operators in preventing human health risk at the workplace. The Level I fugacity approach used in this study demonstrated its suitability for applications to sealed environments such as gasholders and its further refining could provide a useful tool for land remediation risk assessors.

DeepMirTar: a deep-learning approach for predicting human miRNA targets.

Science.gov (United States)

Wen, Ming; Cong, Peisheng; Zhang, Zhimin; Lu, Hongmei; Li, Tonghua

2018-06-01

MicroRNAs (miRNAs) are small noncoding RNAs that function in RNA silencing and post-transcriptional regulation of gene expression by targeting messenger RNAs (mRNAs). Because the underlying mechanisms associated with miRNA binding to mRNA are not fully understood, a major challenge of miRNA studies involves the identification of miRNA-target sites on mRNA. In silico prediction of miRNA-target sites can expedite costly and time-consuming experimental work by providing the most promising miRNA-target-site candidates. In this study, we reported the design and implementation of DeepMirTar, a deep-learning-based approach for accurately predicting human miRNA targets at the site level. The predicted miRNA-target sites are those having canonical or non-canonical seed, and features, including high-level expert-designed, low-level expert-designed, and raw-data-level, were used to represent the miRNA-target site. Comparison with other state-of-the-art machine-learning methods and existing miRNA-target-prediction tools indicated that DeepMirTar improved overall predictive performance. DeepMirTar is freely available at https://github.com/Bjoux2/DeepMirTar_SdA. lith@tongji.edu.cn, hongmeilu@csu.edu.cn. Supplementary data are available at Bioinformatics online.

Source identification of a tar residue from Mumbai Beach

Digital Repository Service at National Institute of Oceanography (India)

Kadam, A; Rokade, M.A

A tar residue from Mumbai Beach, Maharashtra, India was matched with the suspected source sample from a tanker using UV, IR and GLC techniques. Negligible differences in several ratios of UV absorbances and ratios of infrared transmittances...

Saberes e práticas termais: uma perspectiva comparada em Portugal (Termas de S. Pedro do Sul e no Brasil (Caldas da Imperatriz Thermal knowledge and therapies: a comparative view of Portugal (São Pedro do Sul hot springs and Brazil (Caldas da Imperatriz hot springs

Directory of Open Access Journals (Sweden)

Maria Manuel Quintela

2004-01-01

Full Text Available Pretende-se neste artigo discutir como o termalismo, como prática terapêutica, se constituiu como um saber dito 'científico' legitimado pela medicina, que criou estabelecimentos terapêuticos e estâncias termais. Tomaremos como fontes textos dos séculos XIX e XX. A pesquisa foi iniciada em Portugal, em 1996, sendo efetuada uma etnografia das experiências termais nas Termas de S. Pedro do Sul. No Brasil, a pesquisa nas Caldas da Imperatriz foi iniciada em agosto de 2001 e encontra-se ainda em curso.Based on nineteenth- and twentieth-century texts, the article discusses how medicine legitimized the therapeutic practice of thermalism as so-called 'scientific' knowledge, with the creation of therapeutic establishments and hot-springs resorts. My research began in Portugal in 1996, where I produced an ethnography of experiences at the São Pedro do Sul hot springs. My research at Brazil's Caldas da Imperatriz, initiated in August 2001, is still underway.

Anomalous capillary flow of coal tar pitches

Energy Technology Data Exchange (ETDEWEB)

Saint Romain, J.L.; Lahaye, J.; Ehrburger, P.; Couderc, P.

1986-06-01

Capillary flow of liquid coal tar pitch into a coke bed was studied. Anomalies in the flow could not be attributed to a plugging effect for mesophase content lower than 20 wt%. The flow behaviour of small pitch droplets can be correlated with the change in physicochemical properties, as measured by the glass transition temperature, on penetration into the coke bed. 4 references.

A role for nuclear energy in the recovery of oil from the tar sands of Alberta

International Nuclear Information System (INIS)

Puttagunta, V.R.; Sochaski, R.O.; Robertson, R.F.S.

1976-12-01

Techniques of oil recovery from the tar sands and the energy requirements of this operation are described. Fossil fuels, and CANDU reactors are examined as competitive sources of energy for the tar sands plants. The CANDU-OCR reactor appears to have the necessary flexibility to fit into many of the possible methods of recovering oil from the tar sands. Cost comparisons of fossil and nuclear sources show that, for the supply of process steam, the nuclear source is competitive under the criteria of debt financing or low discount rates on capital, continued escalation, and long plant capital write-off period. (author)

HuMiTar: A sequence-based method for prediction of human microRNA targets

Directory of Open Access Journals (Sweden)

Chen Ke

2008-12-01

Full Text Available Abstract Background MicroRNAs (miRs are small noncoding RNAs that bind to complementary/partially complementary sites in the 3' untranslated regions of target genes to regulate protein production of the target transcript and to induce mRNA degradation or mRNA cleavage. The ability to perform accurate, high-throughput identification of physiologically active miR targets would enable functional characterization of individual miRs. Current target prediction methods include traditional approaches that are based on specific base-pairing rules in the miR's seed region and implementation of cross-species conservation of the target site, and machine learning (ML methods that explore patterns that contrast true and false miR-mRNA duplexes. However, in the case of the traditional methods research shows that some seed region matches that are conserved are false positives and that some of the experimentally validated target sites are not conserved. Results We present HuMiTar, a computational method for identifying common targets of miRs, which is based on a scoring function that considers base-pairing for both seed and non-seed positions for human miR-mRNA duplexes. Our design shows that certain non-seed miR nucleotides, such as 14, 18, 13, 11, and 17, are characterized by a strong bias towards formation of Watson-Crick pairing. We contrasted HuMiTar with several representative competing methods on two sets of human miR targets and a set of ten glioblastoma oncogenes. Comparison with the two best performing traditional methods, PicTar and TargetScanS, and a representative ML method that considers the non-seed positions, NBmiRTar, shows that HuMiTar predictions include majority of the predictions of the other three methods. At the same time, the proposed method is also capable of finding more true positive targets as a trade-off for an increased number of predictions. Genome-wide predictions show that the proposed method is characterized by 1.99 signal

Stuck in the tar sands : how the federal government's proposed climate change strategy lets oil companies off the hook

International Nuclear Information System (INIS)

2008-10-01

The credibility of any federal climate change strategy must be measured against its ability to reduce emissions from the tar sands. However, the federal government has proposed a climate change strategy that would allow tar sands producers to double their total emissions over the next decade. This report discussed how the federal government's proposed climate change strategy lets oil companies off the hook. The report discussed the problems and harmful effects associated with tar sands development, including greenhouse gas emissions; water depletion and pollution; toxic air emissions; destruction of the boreal forest; violation of native rights; threat to energy security; and negative socio-economic spin-off from an overheated economy. The federal government's proposed strategy was also assessed in terms of its weak greenhouse gas targets; ignoring the recent growth in tar sands emissions; adopting intensity-based targets instead of hard caps on greenhouse gas pollution, allowing total emissions from the tar sands to keep climbing; putting off critical measures until 2018; awarding oil companies hundreds of millions of dollars in credits for meeting targets they have already adopted voluntarily; lowballing the price of oil and downplaying future growth in tar sands emissions; ignoring huge portions of the oil industry's greenhouse gas pollution; letting oil companies buy their way out at rockbottom prices instead of forcing them to reduce their own emissions; and subsidizing increased tar sands production. It was concluded that the federal government's proposed plan to reduce greenhouse gas emissions was inadequate, because it failed to crack down on rising greenhouse gas emissions from the tar sands, one of Canada's most carbon intensive and fastest growing industries. 29 refs., 1 appendix

Recovery of naphthalene, anthracene, etc. , from tar

Energy Technology Data Exchange (ETDEWEB)

1920-12-25

A process is described for the recovery of naphthalene, anthracene, and the like from tar oils and similar liquors, characterized in that the oil is treated in a rapidly rotating hammer mill, such as a colloid mill, with water sufficient, in the presence or absence of suitable solvents, for the only portion preferably in the presence of emulsifiers; and is filtered through a filter with fine pores.

Lab-scale pyrolysis of the Automotive Shredder Residue light fraction and characterization of tar and solid products.

Science.gov (United States)

Anzano, Manuela; Collina, Elena; Piccinelli, Elsa; Lasagni, Marina

2017-06-01

The general aim of this study is the recovery of Automotive Shredder Residue (ASR). The ASR light fraction, or car fluff, that was collected at an Italian shredding plant was pyrolysed at various temperatures (500-800°C) in a lab-scale reactor. The condensable gases (tar) and solid residue yields increased with decreasing temperature, and these products were characterized to suggest a potential use to reclaim them. The higher heating value (HHV) of tar was 34-37MJ/kg, which is comparable with those of fossil fuels. Furthermore, the ash content was low (0.06-4.98%). Thus, tar can be used as an alternative fuel. With this prospect, the concentrations of polychlorinated dibenzodioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in tar were determined. The toxicity of tar changes with temperature (1-5ng I-TEQ/g), and the PCDFs significantly contribute to tar toxicity, which was 75-100% with a maximum of 99.6% at 700°C. Regarding the characterization of the solid residue, the low HHV (2.4-3.3MJ/kg) does not make it suitable for energy recovery. Regarding material recovery, we considered its use as a filler in construction materials or a secondary source for metals. It shows a high metal concentration (280,000-395,000mg/kg), which is similar at different pyrolysis temperatures. At 500°C, polycyclic aromatic hydrocarbons (PAHs) were not detected in the solid residue, whereas the maximum total PAH concentration (19.41ng/g, 700°C) was lower than that in fly ash from MSWI. In conclusion, 500°C is a suitable pyrolysis temperature to obtain valuable tar and solid residue. Copyright © 2017 Elsevier Ltd. All rights reserved.

Concentrations of polycyclic aromatic hydrocarbons (PAHs) and azaarenes in runoff from coal-tar- and asphalt-sealcoated pavement

International Nuclear Information System (INIS)

Mahler, Barbara J.; Van Metre, Peter C.; Foreman, William T.

2014-01-01

Coal-tar-based sealcoat, used extensively on parking lots and driveways in North America, is a potent source of PAHs. We investigated how concentrations and assemblages of PAHs and azaarenes in runoff from pavement newly sealed with coal-tar-based (CT) or asphalt-based (AS) sealcoat changed over time. Samples of simulated runoff were collected from pavement 5 h to 111 d following application of AS or CT sealcoat. Concentrations of the sum of 16 PAHs (median concentrations of 328 and 35 μg/L for CT and AS runoff, respectively) in runoff varied relatively little, but rapid decreases in concentrations of azaarenes and low molecular weight PAHs were offset by increases in high molecular weight PAHs. The results demonstrate that runoff from CT-sealcoated pavement, in particular, continues to contain elevated concentrations of PAHs long after a 24-h curing time, with implications for the fate, transport, and ecotoxicological effects of contaminants in runoff from CT-sealcoated pavement. - Highlights: • We compare PAH and azaarene concentrations in runoff from coal-tar- and asphalt-sealed pavement. • Concentrations in coal-tar-sealcoat runoff greatly exceeded those in asphalt-sealcoat runoff. • Decreases in azaarenes and LMW PAHs were offset by increases in HMW PAHs. • PAH concentrations in coal-tar-sealcoat runoff remained high for months after application. - Concentrations of PAHs in runoff from pavement with coal-tar-based sealcoat continue to be elevated for at least 3 months following sealcoat application

PAH volatilization following application of coal-tar-based pavement sealant

Science.gov (United States)

Van Metre, Peter C.; Majewski, Michael S.; Mahler, Barbara J.; Foreman, William T.; Braun, Christopher L.; Wilson, Jennifer T.; Burbank, Teresa L.

2012-01-01

Coal-tar-based pavement sealants, a major source of PAHs to urban water bodies, have recently been identified as a source of volatile PAHs to the atmosphere. We tracked the volatilization of PAHs for 1 year after application of a coal-tar-based pavement sealant by measuring gas-phase PAH concentrations above the pavement surface and solid-phase PAH concentrations in sealant scraped from the surface. Gas-phase concentrations at two heights (0.03 and 1.28 m) and wind speed were used to estimate volatilization flux. The sum of the concentrations of eight frequently detected PAHs (ΣPAH8) in the 0.03-m sample 1.6 h after application (297,000 ng m-3) was about 5000 times greater than that previously reported for the same height above unsealed parking lots (66 ng m-3). Flux at 1.6 h after application was estimated at 45,000 μg m-2 h-1 and decreased rapidly during the 45 days after application to 160 μg m-2 h-1. Loss of PAHs from the adhered sealant also was rapid, with about a 50% decrease in solid-phase ΣPAH8 concentration over the 45 days after application. There was general agreement, given the uncertainties, in the estimated mass of ΣPAH8 lost to the atmosphere on the basis of air sampling (2–3 g m-2) and adhered sealant sampling (6 g m-2) during the first 16 days after application, translating to a loss to the atmosphere of one-quarter to one-half of the PAHs in the sealcoat product. Combining the estimated mass of ΣPAH8 released to the atmosphere with a national-use estimate of coal-tar-based sealant suggests that PAH emissions from new coal-tar-based sealcoat applications each year (~1000 Mg) are larger than annual vehicle emissions of PAHs for the United States.

The search for a source rock for the giant Tar Sand triangle accumulation, southeastern Utah

Science.gov (United States)

Huntoon, J.E.; Hansley, P.L.; Naeser, N.D.

1999-01-01

A large proportion (about 36%) of the world's oil resource is contained in accumulations of heavy oil or tar. In these large deposits of degraded oil, the oil in place represents only a fraction of what was present at the time of accumulation. In many of these deposits, the source of the oil is unknown, and the oil is thought to have migrated over long distances to the reservoirs. The Tar Sand triangle in southeastern Utah contains the largest tar sand accumulation in the United States, with 6.3 billion bbl of heavy oil estimated to be in place. The deposit is thought to have originally contained 13-16 billion bbl prior to the biodegradation, water washing, and erosion that have taken place since the middle - late Tertiary. The source of the oil is unknown. The tar is primarily contained within the Lower Permian White Rim Sandstone, but extends into permeable parts of overlying and underlying beds. Oil is interpreted to have migrated into the White Rim sometime during the Tertiary when the formation was at a depth of approximately 3500 m. This conclusion is based on integration of fluid inclusion analysis, time-temperature reconstruction, and apatite fission-track modeling for the White Rim Sandstone. Homogenization temperatures cluster around 85-90??C for primary fluid inclusions in authigenic, nonferroan dolomite in the White Rim. The fluid inclusions are associated with fluorescent oil-bearing inclusions, indicating that dolomite precipitation was coeval with oil migration. Burial reconstruction suggests that the White Rim Sandstone reached its maximum burial depth from 60 to 24 Ma, and that maximum burial was followed by unroofing from 24 to 0 Ma. Time-temperature modeling indicates that the formation experienced temperatures of 85-90??C from about 35 to 40 Ma during maximum burial. Maximum formation temperatures of about 105-110??C were reached at about 24 Ma, just prior to unroofing. Thermal modeling is used to examine the history of potential source rocks

Site-selective probing of cTAR destabilization highlights the necessary plasticity of the HIV-1 nucleocapsid protein to chaperone the first strand transfer

Science.gov (United States)

Godet, Julien; Kenfack, Cyril; Przybilla, Frédéric; Richert, Ludovic; Duportail, Guy; Mély, Yves

2013-01-01

The HIV-1 nucleocapsid protein (NCp7) is a nucleic acid chaperone required during reverse transcription. During the first strand transfer, NCp7 is thought to destabilize cTAR, the (−)DNA copy of the TAR RNA hairpin, and subsequently direct the TAR/cTAR annealing through the zipping of their destabilized stem ends. To further characterize the destabilizing activity of NCp7, we locally probe the structure and dynamics of cTAR by steady-state and time resolved fluorescence spectroscopy. NC(11–55), a truncated NCp7 version corresponding to its zinc-finger domain, was found to bind all over the sequence and to preferentially destabilize the penultimate double-stranded segment in the lower part of the cTAR stem. This destabilization is achieved through zinc-finger–dependent binding of NC to the G10 and G50 residues. Sequence comparison further revealed that C•A mismatches close to the two G residues were critical for fine tuning the stability of the lower part of the cTAR stem and conferring to G10 and G50 the appropriate mobility and accessibility for specific recognition by NC. Our data also highlight the necessary plasticity of NCp7 to adapt to the sequence and structure variability of cTAR to chaperone its annealing with TAR through a specific pathway. PMID:23511968

Marketing 'less harmful, low-tar' cigarettes is a key strategy of the industry to counter tobacco control in China.

Science.gov (United States)

Yang, Gonghuan

2014-03-01

While the 'low-tar' scheme has been widely recognised as a misleading tactic used by the tobacco industry to deceive the public about the true risks of cigarette smoking, a similar campaign using the slogan of 'less harmful, low tar' was launched by the Chinese tobacco industry, that is, State Tobacco Monopoly Administration/China National Tobacco Corporation and began to gain traction during the last decade. Despite the fact that no sufficient research evidence supports the claims made by the industry that these cigarettes are safer, the Chinese tobacco industry has continued to promote them using various health claims. As a result, the production and sales of 'less harmful, low-tar' cigarettes have increased dramatically since 2000. Recently, a tobacco industry senior researcher, whose main research area is 'less harmful, low-tar' cigarettes, was elected as an Academician to the prestigious Chinese Academy of Engineering for his contribution to developing 'less harmful, low-tar' cigarettes. The tobacco researcher's election caused an outcry from the tobacco control community and the general public in China. This paper discusses the Chinese tobacco industry's 'less harmful, low-tar' initiatives and calls for the Chinese government to stop the execution of this deceptive strategy for tobacco marketing.

Spring in the Arab Spring

NARCIS (Netherlands)

Borg, G.J.A.

2011-01-01

Column Gert Borg | Spring in the Arab Spring door dr. Gert Borg, onderzoeker bij Islam en Arabisch aan de Radboud Universiteit Nijmegen en voormalig directeur van het Nederlands-Vlaams Instituut Caïro Spring If, in Google, you type "Arab Spring" and hit the button, you get more than

Quantitative determination of acid oils in low-temperature coal tar by means of fractional distillation

Energy Technology Data Exchange (ETDEWEB)

Jaeger, A

1950-01-01

The aromatic hydroxy compounds in low-temperature tar were separated, and 75 compounds in the boiling range 180/sup 0/ to 320/sup 0/ isolated by means of fractional distillation in packed columns of at least 45 theoretical plates. Mixtures not separable by fractionation were separated by means of other physicochemical or chemical methods. Hydroxy compounds with boiling point up to 230/sup 0/C were detemined quantitatively, as were the phenols present in low-temperature carbonization liquors. With the Krupp-Lurgi process of low-temperature carbonization, 1.8% phenol, 1.8% o-cresol, and 3.6% m-p-cresols were formed. The tar contained up to 1.3% 1:3:5-xylenol and up to 0.9% 1:2:4-xylenol. Of the 12.1% v/v of phenol, cresols, and xylenols present in tar, 11.2% were determined quantitatively, and 9 hydroxy compounds were identified in the remaining 0.9%. On the basis of these investigations, a technical plant that permitted the recovery of pure low-temperature tar phenols and the preparation of a number of different phenol resins from the mixtures was erected.

Studies estimating the dermal bioavailability of polynuclear aromatic hydrocarbons from manufactured plant tar-contaminated soils

International Nuclear Information System (INIS)

Roy, T.A.; Krueger, A.J.; Taylor, B.B.; Mauro, D.M.; Goldstein, L.S.

1998-01-01

In vitro percutaneous absorption studies were performed with contaminated soils or organic extracts of contaminated soils collected at manufactured gas plant (MGP) sites. The MGP tar contaminated soils were found to contain a group of targeted polynuclear aromatic hydrocarbons (PAH) at levels ranging from 10 to 2400 mg/kg. The soil extracts contained target PAH at levels ranging from 12 000 - 34 000 mg/kg. Dermal penetration rates of target PAH from the MGP tar-contaminated soils/soil extracts were determined experimentally through human skin using 3 H-benzo(a)pyrene (BaP) as a surrogate. Results from three MGP sites showed reductions of 2-3 orders of magnitude in PAH absorption through human skin from the most contaminated soils in comparison to the soil extracts. Reduction in PAH penetration can be attributed to PAH concentration and (soil) matrix properties. PAH dermal flux values are used to determine site-specific dermally absorbed dose (DAD) and chronic daily intake (CDI) which are essential terms required to estimate risk associated with human exposure to MGP tar and MGP tar-contaminated soils. 21 refs., 4 figs., 3 tabs

Tar removal from biomass gasification streams: processes and catalysts; Remocao do alcatrao de correntes de gaseificacao de biomassa: processos e catalisadores

Energy Technology Data Exchange (ETDEWEB)

Quitete, Cristina P.B. [Centro de Pesquisa e Desenvolvimento Leopoldo Americo Miguez de Mello (CENPES/PETROBRAS), Rio de Janeiro, RJ (Brazil). Processos de Conversao de Biomassa; Souza, Mariana M.V.M., E-mail: mmattos@eq.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Centro de Tecnologia. Escola de Quimica

2014-07-01

Biomass gasification is a technology that has attracted great interest in synthesis of biofuels and oxo alcohols. However, this gas contains several contaminants, including tar, which need to be removed. Removal of tar is particularly critical because it can lead to operational problems. This review discusses the major pathways to remove tar, with a particular focus on the catalytic steam reforming of tar. Few catalysts have shown promising results; however, long-term studies in the context of real biomass gasification streams are required to realize their potential. (author)

Human papillomavirus and tar hypothesis for squamous cell cervical ...

Indian Academy of Sciences (India)

2010-08-09

Aug 9, 2010 ... Keywords. Cervical cancer; co-factors; human papillomavirus; tar-based vaginal douche; tobacco smoke; wood smoke. Author Affiliations. Christina Bennett1 Allen E Kuhn2 Harry W Haverkos3. Indiana University School of Medicine, Indianapolis, Indiana 46202-5149, USA; Suite 300, Hamilton Mason Road ...

Coal-tar-based sealcoated pavement: A major PAH source to urban stream sediments

International Nuclear Information System (INIS)

Witter, Amy E.; Nguyen, Minh H.; Baidar, Sunil; Sak, Peter B.

2014-01-01

We used land-use analysis, PAH concentrations and assemblages, and multivariate statistics to identify sediment PAH sources in a small (∼1303 km 2 ) urbanizing watershed located in South-Central, Pennsylvania, USA. A geographic information system (GIS) was employed to quantify land-use features that may serve as PAH sources. Urban PAH concentrations were three times higher than rural levels, and were significantly and highly correlated with combined residential/commercial/industrial land use. Principal components analysis (PCA) was used to group sediments with similar PAH assemblages, and correlation analysis compared PAH sediment assemblages to common PAH sources. The strongest correlations were observed between rural sediments (n = 7) and coke-oven emissions sources (r = 0.69–0.78, n = 5), and between urban sediments (n = 22) and coal-tar-based sealcoat dust (r = 0.94, n = 47) suggesting that coal-tar-based sealcoat is an important urban PAH source in this watershed linked to residential and commercial/industrial land use. -- Highlights: • Total PAH concentrations were measured at 35 sites along an urbanizing land-use gradient. • PAH concentrations increased with increasing urban land-use. • Urban land-use metrics were measured at three spatial scales using GIS. • PAH assemblages indicate coal-tar-based sealcoat is a major urban PAH source. • PAH assemblages indicate coke-oven emissions are an important rural PAH source. -- Coal-tar-based sealcoated pavement is a major PAH source to urban freshwater stream sediments in south-central Pennsylvania, USA

Social-cognitive remediation in schizophrenia: generalization of effects of the Training of Affect Recognition (TAR).

Science.gov (United States)

Wölwer, Wolfgang; Frommann, Nicole

2011-09-01

In the last decade, several social cognitive remediation programs have been developed for use in schizophrenia. Though existing evidence indicates that such programs can improve social cognition, which is essential for successful social functioning, it remains unclear whether the improvements generalize to social cognitive domains not primarily addressed by the intervention and whether the improved test performance transfers into everyday social functioning. The present study investigated whether, beyond its known effects on facial affect recognition, the Training of Affect Recognition (TAR) has effects on prosodic affect recognition, theory of mind (ToM) performance, social competence in a role-play task, and more general social and occupational functioning. Thirty-eight inpatients with a diagnosis of schizophrenia or schizoaffective disorder were randomly assigned to 6 weeks of treatment with the TAR--primarily targeted at facial affect recognition-or Cognitive Remediation Training (CRT)--primarily targeted at neurocognition. Intention-to-treat analyses found significantly larger pre-post improvements with TAR than with CRT in prosodic affect recognition, ToM, and social competence and a trend effect in global social functioning. However, the effects on ToM and social competence were no longer significant in the smaller group of patients who completed treatment according to protocol. Results suggest that TAR effects generalize to other social cognitive domains not primarily addressed. TAR may also enhance social skills and social functioning, although this has to be confirmed. Results are discussed with regard to the need to improve functional outcome in schizophrenia against the background of current evidence from other social cognitive remediation approaches.

Tar sands showdown : Canada and the new politics of oil in an age of climate change

International Nuclear Information System (INIS)

Clarke, T.

2009-01-01

This book outlined the social and environmental issues facing the oil sands industry in Canada, including economic sovereignty, energy security, water rights and free trade. The tar sands have become vital to the Canadian economy, as they have the potential to increase Canada's foreign oil output by 4 to 5 times in the next 15 years. The author discussed the ecological and social impact of the Alberta tar sands and the real cost of development to Albertans and Canadians. Tar sands oil production generates more than 3 times the amount of greenhouse gas emissions than conventional oil production. The industry is also becoming a prime example of the abuse of water sources. The author emphasized the need to build an alternative energy future in an age of global warming. The main objective of this book was to help stimulate a nation-wide public debate about the tar sands and the critical issues at stake regarding Canada's energy future and an environmental strategy for more sustainable development. refs., tabs., figs.

Gc/ms analysis of coal tar composition produced from coal

African Journals Online (AJOL)

Coal pyrolysis is one of the significant approaches for the comprehensive utilization ... planigraphy-GC/MS; therefore a satisfactory analytical result obtained, which .... Among the aliphatic group of the coal tar, the proportion of alkene is larger ...

Idrætskultur i løb, spring og kast

DEFF Research Database (Denmark)

Knudsen, Martin Elmbæk

”Idrætskultur i løb, spring og kast” er et læremiddel til skoleidræt – til mellemtrinnet! Læremidlet indeholder denne lærebog, som er udarbejdet til elever i Aarhus Kommune. Anledningen er, at byen afholder SkoleOL, og at Aarhus er europæisk kulturhovedstad i 2017. Det sætter sit præg på den måde......, at lærebogen er tematisk opbygget med et ”kultur”-fokus. Så arbejdet med lærebogen kommer omkring skoleidrættens mål inden for områderne ”samarbejde og ansvar”, ”normer og værdier”, ”idrætten i samfundet” og de idrætslige færdigheder i ”løb, spring og kast”. Læremidlet Idrætskultur i løb, spring og kast...

In situ heat treatment of a tar sands formation after drive process treatment

Science.gov (United States)

Vinegar, Harold J.; Stanecki, John

2010-09-21

A method for treating a tar sands formation includes providing a drive fluid to a hydrocarbon containing layer of the tar sands formation to mobilize at least some hydrocarbons in the layer. At least some first hydrocarbons from the layer are produced. Heat is provided to the layer from one or more heaters located in the formation. At least some second hydrocarbons are produced from the layer of the formation. The second hydrocarbons include at least some hydrocarbons that are upgraded compared to the first hydrocarbons produced by using the drive fluid.

Cigarettes, lung cancer, and coronary heart disease: the effects of inhalation and tar yield.

Science.gov (United States)

Higenbottam, T; Shipley, M J; Rose, G

1982-06-01

Ten-year mortality rates for lung cancer and coronary heart disease have been related to cigarette smoking habits in 17 475 male civil servants aged 40-64 and in sample of 8089 male British residents aged 35-69. Both diseases were more frequent in smokers. Lung cancer rates were higher overall for "non-inhalers", particularly in heavy smokers. Tar yield correlated with the risk of lung cancer in non-inhalers but less so in inhalers. Conversely, coronary deaths were more common among inhalers, and the effect of tar/nicotine yield (such as it was) was confined to inhalers. It appears that there are subtle interactions between the amount smoked, the tar/nicotine yield of the cigarette, and the style of smoking. Thus the effects of a change in cigarette characteristics are hard to predict, and they may be different for respiratory and cardiovascular disease.

Properties of gasification-derived char and its utilization for catalytic tar reforming

Science.gov (United States)

Qian, Kezhen

Char is a low-value byproduct of biomass gasification and pyrolysis with many potential applications, such as soil amendment and the synthesis of activated carbon. The overall goal of the proposed research was to develop novel methods to use char derived from gasification for high-value applications in syngas conditioning. The first objective was to investigate effects of gasification condition and feedstock on properties of char derived from fluidized bed gasification. Results show that the surface areas of most of the char were 1--10 m 2/g and increased as the equivalence ratio increased. Char moisture and fixed carbon contents decreased while ash content increased as equivalence ratio increased. The next objective was to study the properties of sorghum and red cedar char derived from downdraft gasifier. Red cedar char contained more aliphatic carbon and o-alkyl carbon than sorghum char. Char derived from downdraft gasification had higher heating values and lower ash contents than char derived from fluidized bed gasification. The gasification reactivity of red cedar char was higher than that of sorghum char. Then, red cedar char based catalysts were developed with different preparation method to reform toluene and naphthalene as model tars. The catalyst prepared with nickel nitrate was found to be better than that with nickel acetate. The nickel particle size of catalyst impregnated with nickel nitrate was smaller than that of catalyst impregnated with nickel acetate. The particle size of catalyst impregnated with nickel acetate decreased by hydrazine reduction. The catalyst impregnated with nickel nitrate had the highest toluene removal efficiency, which was 70%--100% at 600--800 °C. The presence of naphthalene in tar reduced the catalyst efficiency. The toluene conversion was 36--99% and the naphthalene conversion was 37%--93% at 700--900 °C. Finally, effects of atmosphere and pressure on catalytic reforming of lignin-derived tars over the developed catalyst

Characterization of alkanes, hopanes, and polycyclic aromatic hydrocarbons (PAHs) in tar-balls collected from the East Coast of Peninsular Malaysia.

Science.gov (United States)

Chandru, Kuhan; Zakaria, Mohamad Pauzi; Anita, Sofia; Shahbazi, Azadeh; Sakari, Mahyar; Bahry, Pourya Shahpoury; Mohamed, Che Abd Rahim

2008-05-01

The East Coast of Peninsular Malaysia faces the South China Sea and is vulnerable to oil pollution because of intense petroleum production activities in the area. The South China Sea is also a favored route for supertankers carrying crude oil to the Far East. Consequently, oil spills can occur, causing pollution and contamination in the surrounding areas. Residual oil spills stranded on coastal beaches usually end up as tar-balls. Elucidating the sources of tar-balls using a molecular marker approach is essential in assessing environmental impacts and perhaps settling legal liabilities for affected parties. This study utilizes a multimodal molecular marker approach through the use of diagnostic ratios of alkanes, hopanes, and polycyclic aromatic hydrocarbons (PAHs) to determine the source, distribution and weathering of tar-balls. Hopane ratios (e.g., C29/C30, and summation C31-C35/C30 ratios) were used to identify the sources of tar-balls. The weathering effects were distinguished by using alkanes, namely the unresolved complex mixture (UCM) and low molecular weight/high molecular weight (L/H) ratios. Similarly, PAHs were also used for the determination of weathering processes undergone by the tar-balls. This multimodal molecular marker gave a very strong indication of the sources of tar-balls in this study. For example, 16 out of 17 samples originated from South East Asian Crude Oil (SEACO) with one sample from Merang, Terengganu originating from North Sea Oil (Troll). The TRME-2 sample may have come from a supertanker's ballast water discharge. The second possibility is that the tar-ball may have been transported via oceanographic currents. All 'weathered' sample characterizations were based on the presence of UCM and other ratios. The multimodal molecular marker approach applied in this study has enabled us to partially understand the transport behavior of tar-balls in the marine environment and has revealed insights into the weathering process of tar-balls.

Characterisation and catalytic upgrading of tars from coal-tyre hydropyrolysis

Energy Technology Data Exchange (ETDEWEB)

Mastral, A.M.; Murillo, R.; Callen, M.S.; Garcia, T. [Instituto de Carboquimica, Zaragoza (Spain)

1999-07-01

Tars from coal-tyre hydropyrolysis obtained in a swept fixed bed reactor were upgraded with catalysts. Upgraded oils were characterized, and naphtha, kerosene, gas oil, heavy gas oil and vacuum residue percentages were quantified. 7 refs., 3 tabs.

Class I cultural resource overview for oil shale and tar sands areas in Colorado, Utah and Wyoming.

Energy Technology Data Exchange (ETDEWEB)

O' Rourke, D.; Kullen, D.; Gierek, L.; Wescott, K.; Greby, M.; Anast, G.; Nesta, M.; Walston, L.; Tate, R.; Azzarello, A.; Vinikour, B.; Van Lonkhuyzen, B.; Quinn, J.; Yuen, R.; Environmental Science Division

2007-11-01

In August 2005, the U.S. Congress enacted the Energy Policy Act of 2005, Public Law 109-58. In Section 369 of this Act, also known as the 'Oil Shale, Tar Sands, and Other Strategic Unconventional Fuels Act of 2005', Congress declared that oil shale and tar sands (and other unconventional fuels) are strategically important domestic energy resources that should be developed to reduce the nation's growing dependence on oil from politically and economically unstable foreign sources. The Bureau of Land Management (BLM) is developing a Programmatic Environmental Impact Statement (PEIS) to evaluate alternatives for establishing commercial oil shale and tar sands leasing programs in Colorado, Wyoming, and Utah. This PEIS evaluates the potential impacts of alternatives identifying BLM-administered lands as available for application for commercial leasing of oil shale resources within the three states and of tar sands resources within Utah. The scope of the analysis of the PEIS also includes an assessment of the potential effects of future commercial leasing. This Class I cultural resources study is in support of the Draft Oil Shale and Tar Sands Resource Management Plan Amendments to Address Land Use Allocations in Colorado, Utah, and Wyoming and Programmatic Environmental Impact Statement and is an attempt to synthesize archaeological data covering the most geologically prospective lands for oil shale and tar sands in Colorado, Utah, and Wyoming. This report is based solely on geographic information system (GIS) data held by the Colorado, Utah, and Wyoming State Historic Preservation Offices (SHPOs). The GIS data include the information that the BLM has provided to the SHPOs. The primary purpose of the Class I cultural resources overview is to provide information on the affected environment for the PEIS. Furthermore, this report provides recommendations to support planning decisions and the management of cultural resources that could be impacted by future

Guideline for Sampling and Analysis of Tar and Particles in Biomass Producer Gases. Version 3.3

Energy Technology Data Exchange (ETDEWEB)

Neeft, J.P.A.; Knoef, H.A.M.; Zielke, U.; Sjoestroem, K.; Hasler, P.; Simell, P.A.; Dorrington, M.A.; Thomas, L.; Abatzoglou, N.; Deutch, S.; Greil, C.; Buffinga, G.J.; Brage, C.; Suomalainen, M.

2002-07-01

This Guideline provides a set of procedures for the measurement of organic contaminants and particles in producer gases from biomass gasifiers. The procedures are designed to cover different gasifier types (updraft or downdraft fixed bed or fluidised bed gasifiers), operating conditions (0 - 900C and 0.6-60 bars) and concentration ranges (1 mg/m{sub n}{sup 3} to 300 g/m{sub n}{sup 3}). The Guideline describes a modular sampling train, and a set of procedures, which include: planning and preparation of the sampling, sampling and post-sampling, analysis, calculations, error analysis and reporting. The modular sampling train consists of 4 modules. Module 1 is a preconditioning module for isokinetic sampling and gas cooling. Module 2 is a particle collection module including a heated filter. Module 3 is a tar collection module with a gas quench (optionally by circulating a liquid), impinger bottles and a backup adsorber. Module 4 is a volume-sampling module consisting of a pump, a rotameter, a gas flow meter and pressure and temperature indicators. The equipment and materials that are required for procuring this modular sampling train are given in the Guideline. The sampling procedures consist of a description for isokinetic sampling, a leakage test prior to sampling, the actual sampling and its duration, how the equipment is cleaned after the sampling, and how the samples are prepared and stored. Analysis of the samples is performed via three procedures. Prior to these procedures, the sample is prepared by Soxhlet extraction of the tars on the particle filter and by collection of all tars in one bulk solution. The first procedure describes the weighing of the particle filter to obtain the concentration of particles in the biomass producer gas. The bulk tar solution is used for two purposes: for determination of gravimetric tar and for analysis of individual compounds. The second procedure describes how to determine the gravimetric tar mass from the bulk solution. The

Treatment of low-temperature tar-gas mixtures

Energy Technology Data Exchange (ETDEWEB)

Schick, F

1928-07-04

Process for the treating and conversion of low-temperature tar-vapor and gas mixtures in the presence of metals or metal oxides as well as bodies of large surface, without previous condensation of the liquid material to be treated, characterized by the treatment taking place with a mixture of desulfurizing metals and metal oxides which, if necessary, are precipitated on carriers and large surface nonmetal cracking catalysts, such as active carbon and silica gel.

Receiving demulsifying agent from the acid tar

Energy Technology Data Exchange (ETDEWEB)

Nikitina, A.A.; Belyaeva, A.S.; Kunakova, R.V. [FGBIHE ' Ufa State Academy of Economics and Services' , Ufa (Russian Federation); Movsumzade, E.M. [FGBIHE ' Ufa State Petroleum Technological Univ.' , Ufa (Russian Federation); Lapidus, A.L. [Russian Academy of Sciences, Moscow (Russian Federation). N.D. Zelinsky Institute of Organic Chemistry

2012-07-01

The processing of wastes of petrochemical production makes it possible to reduce the price of produced commodity of petroleum products substantially. Bitumen, fuel oils, tars and other mixture of heavy organic compounds are widely used in road construction, in paint and cable industries, manufacture of roofing materials, are used as boiler and furnace fuel, fuel for marine diesel engines, raw material for the production of modifying additives, fillers, surfaceactive substances, etc. (orig.)

Brown carbon in tar balls from smoldering biomass combustion

Science.gov (United States)

R. K. Chakrabarty; H. Moosmuller; L.-W. A. Chen; K. Lewis; W. P. Arnott; C. Mazzoleni; M. K. Dubey; C. E. Wold; W. M. Hao; S. M. Kreidenweis

2010-01-01

We report the direct observation of laboratory production of spherical, carbonaceous particles - "tar balls" - from smoldering combustion of two commonly occurring dry mid-latitude fuels. Real-time measurements of spectrally varying absorption Angstrom coefficients (AAC) indicate that a class of light absorbing organic carbon (OC) with wavelength dependent...

Radiocarbon dating of extinct fauna in the Americas recovered from tar pits

International Nuclear Information System (INIS)

Jull, A.J.T.; Iturralde-Vinent, M.; O'Malley, J.M.; MacPhee, R.D.E.; McDonald, H.G.; Martin, P.S.; Moody, J.; Rincon, A.

2004-01-01

We have obtained radiocarbon dates by accelerator mass spectrometry on bones of extinct large mammals from tar pits. Results on some samples of Glyptodon and Holmesina (extinct large mammals similar to armadillos) yielded ages of >25 and >21 ka, respectively. We also studied the radiocarbon ages of three different samples of bones from the extinct Cuban ground sloth, Parocnus bownii, which yielded dates ranging from 4960 ± 280 to 11 880 ± 420 yr BP. In order to remove the tar component pretreat the samples sufficiently to obtain reliable dates, we cleaned the samples by Soxhlet extraction in benzene. Resulting samples of collagenous material were often small

ANALYSIS OF MEASURED AND MODELED SOLAR RADIATION AT THE TARS SOLAR HEATING PLANT IN DENMARK

DEFF Research Database (Denmark)

Tian, Zhiyong; Perers, Bengt; Furbo, Simon

2017-01-01

, such as solar radiation, inlet and outlet temperature for the solar collector field, flow rate and pressure, ambient temperature, Wind speed and wind direction were measured. Global horizontal radiation, direct normal irradiation (DNI) and total radiation on the tilted collector plane of the flat plate...... collector field have been measured in Tars solar heating plant. To determine the accuracy of modeled and measured solar radiation in Tars solar heating plant, monthly comparisons of measured and calculated radiation using 6 empirical models have been carried out. Comparisons of measured and modeled total......A novel combined solar heating plant with tracking parabolic trough collectors (PTC) and flat plate collectors (FPC) has been constructed and put into operation in Tars, 30 km north of Aalborg, Denmark in August 2015. To assess the operation performance of the plant, detailed parameters...

Spring performance tester for miniature extension springs

Science.gov (United States)

Salzbrenner, Bradley; Boyce, Brad

2017-05-16

A spring performance tester and method of testing a spring are disclosed that has improved accuracy and precision over prior art spring testers. The tester can perform static and cyclic testing. The spring tester can provide validation for product acceptance as well as test for cyclic degradation of springs, such as the change in the spring rate and fatigue failure.

Parallels between playbacks and Pleistocene tar seeps suggest sociality in an extinct sabretooth cat, Smilodon

OpenAIRE

Carbone, Chris; Maddox, Tom; Funston, Paul J.; Mills, Michael G.L.; Grether, Gregory F.; Van Valkenburgh, Blaire

2008-01-01

Inferences concerning the lives of extinct animals are difficult to obtain from the fossil record. Here we present a novel approach to the study of extinct carnivores, using a comparison between fossil records (n=3324) found in Late Pleistocene tar seeps at Rancho La Brea in North America and counts (n=4491) from playback experiments used to estimate carnivore abundance in Africa. Playbacks and tar seep deposits represent competitive, potentially dangerous encounters where multiple predators ...

Traditional African Religions (TARs): on HIV/AIDS, health and ...

African Journals Online (AJOL)

This is because the moral guidance put forward by. African religions is underestimated; hence making HIV/AIDS more of a moral problem. Rethinking the dialogue with TARs, will help in setting appropriate means of enhancing health in a broad sense and living in human dignity in Africa. Mtafiti Mwafrika Vol. 15 2005: pp.

Coal-tar-based pavement sealcoat and PAHs: implications for the environment, human health, and stormwater management.

Science.gov (United States)

Mahler, Barbara J; Metre, Peter C Van; Crane, Judy L; Watts, Alison W; Scoggins, Mateo; Williams, E Spencer

2012-03-20

Coal-tar-based sealcoat products, widely used in the central and eastern U.S. on parking lots, driveways, and even playgrounds, are typically 20-35% coal-tar pitch, a known human carcinogen that contains about 200 polycyclic aromatic hydrocarbon (PAH) compounds. Research continues to identify environmental compartments-including stormwater runoff, lake sediment, soil, house dust, and most recently, air-contaminated by PAHs from coal-tar-based sealcoat and to demonstrate potential risks to biological communities and human health. In many cases, the levels of contamination associated with sealed pavement are striking relative to levels near unsealed pavement: PAH concentrations in air over pavement with freshly applied coal-tar-based sealcoat, for example, were hundreds to thousands of times higher than those in air over unsealed pavement. Even a small amount of sealcoated pavement can be the dominant source of PAHs to sediment in stormwater-retention ponds; proper disposal of such PAH-contaminated sediment can be extremely costly. Several local governments, the District of Columbia, and the State of Washington have banned use of these products, and several national and regional hardware and home-improvement retailers have voluntarily ceased selling them.

Coal-tar-based pavement sealcoat and PAHs: implications for the environment, human health, and stormwater management

Science.gov (United States)

Mahler, Barbara J.; Van Metre, Peter C.; Crane, Judy L.; Watts, Alison W.; Scoggins, Mateo; Williams, E. Spencer

2012-01-01

Coal-tar-based sealcoat products, widely used in the central and eastern U.S. on parking lots, driveways, and even playgrounds, are typically 20-35% coal-tar pitch, a known human carcinogen that contains about 200 polycyclic aromatic hydrocarbon (PAH) compounds. Research continues to identify environmental compartments—including stormwater runoff, lake sediment, soil, house dust, and most recently, air—contaminated by PAHs from coal-tar-based sealcoat and to demonstrate potential risks to biological communities and human health. In many cases, the levels of contamination associated with sealed pavement are striking relative to levels near unsealed pavement: PAH concentrations in air over pavement with freshly applied coal-tar-based sealcoat, for example, were hundreds to thousands of times higher than those in air over unsealed pavement. Even a small amount of sealcoated pavement can be the dominant source of PAHs to sediment in stormwater-retention ponds; proper disposal of such PAH-contaminated sediment can be extremely costly. Several local governments, the District of Columbia, and the State of Washington have banned use of these products, and several national and regional hardware and home-improvement retailers have voluntarily ceased selling them.

Coal-tar pavement sealants might substantially increase children's PAH exposures

Science.gov (United States)

Williams, E. Spencer; Mahler, Barbara J.; Van Metre, Peter C.

2012-01-01

Dietary ingestion has been identified repeatedly as the primary route of human exposure to polycyclic aromatic hydrocarbons (PAHs), seven of which are classified as probable human carcinogens (B2 PAHs) by the U.S. EPA. Humans are exposed to PAHs through ingestion of cooked and uncooked foods, incidental ingestion of soil and dust, inhalation of ambient air, and absorption through skin. Although PAH sources are ubiquitous in the environment, one recently identified PAH source stands out: Coal-tar-based pavement sealant—a product applied to many parking lots, driveways, and even playgrounds primarily in the central, southern, and eastern U.S.—has PAH concentrations 100–1000 times greater than most other PAH sources. It was reported recently that PAH concentrations in house dust in residences adjacent to parking lots with coal-tar-based sealant were 25 times higher than in residences adjacent to unsealed asphalt parking lots.

Analysis of the maximum discharge of karst springs

Science.gov (United States)

Bonacci, Ognjen

2001-07-01

Analyses are presented of the conditions that limit the discharge of some karst springs. The large number of springs studied show that, under conditions of extremely intense precipitation, a maximum value exists for the discharge of the main springs in a catchment, independent of catchment size and the amount of precipitation. Outflow modelling of karst-spring discharge is not easily generalized and schematized due to numerous specific characteristics of karst-flow systems. A detailed examination of the published data on four karst springs identified the possible reasons for the limitation on the maximum flow rate: (1) limited size of the karst conduit; (2) pressure flow; (3) intercatchment overflow; (4) overflow from the main spring-flow system to intermittent springs within the same catchment; (5) water storage in the zone above the karst aquifer or epikarstic zone of the catchment; and (6) factors such as climate, soil and vegetation cover, and altitude and geology of the catchment area. The phenomenon of limited maximum-discharge capacity of karst springs is not included in rainfall-runoff process modelling, which is probably one of the main reasons for the present poor quality of karst hydrological modelling. Résumé. Les conditions qui limitent le débit de certaines sources karstiques sont présentées. Un grand nombre de sources étudiées montrent que, sous certaines conditions de précipitations extrêmement intenses, il existe une valeur maximale pour le débit des sources principales d'un bassin, indépendante des dimensions de ce bassin et de la hauteur de précipitation. La modélisation des débits d'exhaure d'une source karstique n'est pas facilement généralisable, ni schématisable, à cause des nombreuses caractéristiques spécifiques des écoulements souterrains karstiques. Un examen détaillé des données publiées concernant quatre sources karstiques permet d'identifier les raisons possibles de la limitation de l'écoulement maximal: (1

How do different cigarette design features influence the standard tar yields of popular cigarette brands sold in different countries?

Science.gov (United States)

O'Connor, R J; Hammond, D; McNeill, A; King, B; Kozlowski, L T; Giovino, G A; Cummings, K M

2008-09-01

To examine the associations among cigarette design features and tar yields of leading cigarette brands sold in the United States, Canada, Australia and the United Kingdom. Government reports and numbers listed on packs were used to obtain data on International Organization for Standardization (ISO)/Federal Trade Commission (FTC) yields for the tar of 172 cigarette varieties sold in the United States, Canada, Australia and the United Kingdom. We used standardised methods to measure the following 11 cigarette design parameters: filter ventilation, cigarette pressure drop, filter pressure drop, tobacco rod length, filter length, cigarette diameter, tipping paper length, tobacco weight, filter weight, rod density and filter density. Filter ventilation was found to be the predominant design feature accounting for the variations between brands in ISO/FTC tar yields in each of the four countries. After accounting for filter ventilation, design parameters such as overwrap length, tobacco weight and rod density played comparatively minor roles in determining tar yields. Variation in ISO/FTC tar yields are predicted by a limited set of cigarette design features, especially filter ventilation, suggesting that governments should consider mandatory disclosure of cigarette design parameters as part of comprehensive tobacco product regulations.

Fresh tar (from biomass gasification) destruction with downstream catalysts: comparison of their intrinsic activity with a realistic kinetic model

Energy Technology Data Exchange (ETDEWEB)

Corella, J.; Narvaez, I.; Orio, A. [Complutense Univ. of Madrid (Spain). Dept. of Chemical Engineering

1996-12-31

A model for fresh tar destruction over catalysts placed downstream a biomass gasifier is presented. It includes the stoichio-metry and the calculation of the kinetic constants for the tar destruction. Catalysts studied include commercial Ni steam reforming catalysts and calcinated dolomites. Kinetic constants for tar destruction are calculated for several particle sizes, times- on-stream and temperatures of the catalyst and equivalence ratios in the gasifier. Such intrinsic kinetic constants allow a rigorous or scientific comparison of solids and conditions to be used in an advanced gasification process. (orig.) 4 refs.

Fresh tar (from biomass gasification) destruction with downstream catalysts: comparison of their intrinsic activity with a realistic kinetic model

Energy Technology Data Exchange (ETDEWEB)

Corella, J; Narvaez, I; Orio, A [Complutense Univ. of Madrid (Spain). Dept. of Chemical Engineering

1997-12-31

A model for fresh tar destruction over catalysts placed downstream a biomass gasifier is presented. It includes the stoichio-metry and the calculation of the kinetic constants for the tar destruction. Catalysts studied include commercial Ni steam reforming catalysts and calcinated dolomites. Kinetic constants for tar destruction are calculated for several particle sizes, times- on-stream and temperatures of the catalyst and equivalence ratios in the gasifier. Such intrinsic kinetic constants allow a rigorous or scientific comparison of solids and conditions to be used in an advanced gasification process. (orig.) 4 refs.

Changes in tar yields and cigarette design in samples of Chinese cigarettes, 2009 and 2012.

Science.gov (United States)

Schneller, Liane M; Zwierzchowski, Benjamin A; Caruso, Rosalie V; Li, Qiang; Yuan, Jiang; Fong, Geoffrey T; O'Connor, Richard J

2015-11-01

China is home to the greatest number of smokers as well as the greatest number of smoking-related deaths. An active and growing market of cigarettes marketed as 'light' or 'low tar' may keep health-concerned smokers from quitting, wrongly believing that such brands are less harmful. This study sought to observe changes in cigarette design characteristics and reported tar, nicotine and carbon monoxide (TNCO) levels in a sample of cigarette brands obtained in seven Chinese cities from 2009 to 2012. Cigarettes were purchased and shipped to Roswell Park Cancer Institute, where 91 pairs of packs were selected for physical cigarette design characteristic testing and recording of TNCO values. Data analysis was conducted using SPSS, and was initially characterised using descriptive statistics, correlations and generalised estimating equations to observe changes in brand varieties over time. Reported TNCO values on packs saw mean tar, nicotine and CO levels decrease from 2009 to 2012 by 7.9%, 4.5% and 6.0%, respectively. Ventilation was the only cigarette design feature that significantly changed over time (p<0.001), with an increase of 31.7%. Significant predictors of tar and CO yield overall were ventilation and per-cigarette tobacco weight, while for nicotine tobacco moisture was also an independent predictor of yield. The use of ventilation to decrease TNCO emissions is misleading smokers to believe that they are smoking a 'light/low' tar cigarette that is healthier, and is potentially forestalling the quitting behaviours that would begin to reduce the health burden of tobacco in China, and so should be prohibited. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Perversities of Extreme Dependence and Unequal Growth in the TAR

NARCIS (Netherlands)

A.M. Fischer (Andrew Martín)

2007-01-01

textabstractThe official Chinese press recently came out with a series of articles reporting the latest statistics on the phenomenally rapid economic growth that has been taking place in the Tibet Autonomous Region (TAR) since the mid-1990s through sheer force of Central Government subsidies.

PAHs underfoot: Contaminated dust from coal-tar sealcoated pavement is widespread in the United States

Science.gov (United States)

Van Metre, P.C.; Mahler, B.J.; Wilson, J.T.

2009-01-01

We reported in 2005 that runoff from parking lots treated with coal-tar-based sealcoat was a major source of polycyclic aromatic hydrocarbons (PAHs) to streams in Austin, Texas. Here we present new data from nine U. S. cities that show nationwide patterns in concentrations of PAHs associated with sealcoat Dust was swept from parking lots in six cities in the central and eastern U. S., where coal-tar-based sealcoat dominates use, and three cities in the western U. S., where asphalt-based sealcoat dominates use. For six central and eastern cities, median ?? PAH concentrations in dust from sealcoated and unsealcoated pavement are 2200 and 27 mg/kg, respectively. For three western cities, median ?? PAH concentrations in dust from sealcoated and unsealcoated pavement are similar and very low (2. 1 and 0. 8 mg/kg, respectively). Lakes in the central and eastern cities where pavement was sampled have bottom sediments with higher PAH concentrations than do those in the western cities relative to degree of urbanization. Bottom-sediment PAH assemblages are similar to those of sealcoated pavement dust regionally, implicating coal-tar-based sealcoat as a PAH source to the central and eastern lakes. Concentrations of benzo[a]pyrene in dust from coal-tar sealcoated pavement and adjacent soils greatly exceed generic soil screening levels, suggesting that research on human-health risk is warranted.

Geology and resources of the Tar Sand Triangle, southeastern Utah

Energy Technology Data Exchange (ETDEWEB)

Dana, G.F.; Oliver, R.L.; Elliott, J.R.

1984-05-01

The Tar Sand Triangle is located in southeastern Utah between the Dirty Devil and Colorado Rivers and covers an area of about 200 square miles. The geology of the area consists of gently northwest dipping strata exposed in the box canyons and slopes of the canyonlands morphology. Strata in the area range in age from Jurassic to Permian. The majority of tar sand saturation is found in the Permian White Rim Sandstone Member of the Cutler Formation. The White Rim Sandstone Member consists of a clean, well-sorted sandstone which was deposited in a shallow marine environment. Resources were calculated from analytical data from the three coreholes drilled by the Laramie Energy Technology Center and other available data. The total in-place resources, determined from this study, are 6.3 billion barels. Previous estimates ranged from 2.9 to 16 million barrels. More coring and analyses will be necessary before a more accurate determination of resources can be attempted. 8 references, 11 figures, 7 tables.

PeaTAR1B: Characterization of a Second Type 1 Tyramine Receptor of the American Cockroach, Periplaneta americana.

Science.gov (United States)

Blenau, Wolfgang; Balfanz, Sabine; Baumann, Arnd

2017-10-30

The catecholamines norepinephrine and epinephrine regulate important physiological functions in vertebrates. In insects; these neuroactive substances are functionally replaced by the phenolamines octopamine and tyramine. Phenolamines activate specific guanine nucleotide-binding (G) protein-coupled receptors (GPCRs). Type 1 tyramine receptors are better activated by tyramine than by octopamine. In contrast; type 2 tyramine receptors are almost exclusively activated by tyramine. Functionally; activation of type 1 tyramine receptors leads to a decrease in the intracellular concentration of cAMP ([cAMP] i ) whereas type 2 tyramine receptors can mediate Ca 2+ signals or both Ca 2+ signals and effects on [cAMP] i . Here; we report that the American cockroach ( Periplaneta americana ) expresses a second type 1 tyramine receptor (PeaTAR1B) in addition to PeaTAR1A (previously called PeaTYR1). When heterologously expressed in flpTM cells; activation of PeaTAR1B by tyramine leads to a concentration-dependent decrease in [cAMP] i . Its activity can be blocked by a series of established antagonists. The functional characterization of two type 1 tyramine receptors from P. americana ; PeaTAR1A and PeaTAR1B; which respond to tyramine by changing cAMP levels; is a major step towards understanding the actions of tyramine in cockroach physiology and behavior; particularly in comparison to the effects of octopamine.

PeaTAR1B: Characterization of a Second Type 1 Tyramine Receptor of the American Cockroach, Periplaneta americana

Directory of Open Access Journals (Sweden)

Wolfgang Blenau

2017-10-01

Full Text Available The catecholamines norepinephrine and epinephrine regulate important physiological functions in vertebrates. In insects; these neuroactive substances are functionally replaced by the phenolamines octopamine and tyramine. Phenolamines activate specific guanine nucleotide-binding (G protein-coupled receptors (GPCRs. Type 1 tyramine receptors are better activated by tyramine than by octopamine. In contrast; type 2 tyramine receptors are almost exclusively activated by tyramine. Functionally; activation of type 1 tyramine receptors leads to a decrease in the intracellular concentration of cAMP ([cAMP]i whereas type 2 tyramine receptors can mediate Ca2+ signals or both Ca2+ signals and effects on [cAMP]i. Here; we report that the American cockroach (Periplaneta americana expresses a second type 1 tyramine receptor (PeaTAR1B in addition to PeaTAR1A (previously called PeaTYR1. When heterologously expressed in flpTM cells; activation of PeaTAR1B by tyramine leads to a concentration-dependent decrease in [cAMP]i. Its activity can be blocked by a series of established antagonists. The functional characterization of two type 1 tyramine receptors from P. americana; PeaTAR1A and PeaTAR1B; which respond to tyramine by changing cAMP levels; is a major step towards understanding the actions of tyramine in cockroach physiology and behavior; particularly in comparison to the effects of octopamine.

Calcipotriol versus coal tar: a prospective randomized study in stable plaque psoriasis

Energy Technology Data Exchange (ETDEWEB)

Sharma, V.; Kaur, I.; Kumar, B. [Postgraduate Institute of Medicinal Education & Research, Chandigarh (India)

2003-10-01

Topical therapies are the first line of treatment for patients with stable plaque psoriasis (SPP) affecting a limited body surface area. Very few trials comparing newer agents, such as 0.005% topical calcipotriol, with conventional modes of therapy, such as coal tar ointment, have been reported. A prospective, right-left randomized, investigator-blinded study with a 12-week treatment period and an 8-week follow-up period was performed. It was found that 0.005% calcipotriol ointment produced a faster initial response and had better cosmetic acceptability in patients, although after a long period of treatment, i.e. 12 weeks, 5% coal tar ointment had comparable efficacy. There was no statistically significant difference in the relapse rates between the two modalities.

Heating tar sands formations to visbreaking temperatures

Science.gov (United States)

Karanikas, John Michael [Houston, TX; Colmenares, Tulio Rafael [Houston, TX; Zhang, Etuan [Houston, TX; Marino, Marian [Houston, TX; Roes, Augustinus Wilhelmus Maria [Houston, TX; Ryan, Robert Charles [Houston, TX; Beer, Gary Lee [Houston, TX; Dombrowski, Robert James [Houston, TX; Jaiswal, Namit [Houston, TX

2009-12-22

Methods for treating a tar sands formation are described herein. Methods may include heating at least a section of a hydrocarbon layer in the formation from a plurality of heaters located in the formation. The heat may be controlled so that at least a majority of the section reaches an average temperature of between 200.degree. C. and 240.degree. C., which results in visbreaking of at least some hydrocarbons in the section. At least some visbroken hydrocarbon fluids may be produced from the formation.

Use of advanced chemical fingerprinting in PAH source identification and allocation at a coal tar processing site

International Nuclear Information System (INIS)

Brown, J.S.; Boehm, P.D.; Douglas, G.S.

1995-01-01

Advanced chemical fingerprinting analyses were used to determine source allocation at a former coal tar processing facility which had been converted to a petroleum recycling site. Soil samples from the site had high petroleum hydrocarbon concentrations and elevated levels of polynuclear aromatic hydrocarbons (PAH). Comparisons of PAH distributions were used to differentiate the coal tar hydrocarbons from the petroleum hydrocarbons in soil samples. A more specific technique was needed to accurately allocate the contribution of the two sources to the observed PAH contamination in the soil. Petroleum biomarkers (steranes and triterpanes) which are present in crude oils and many refined petroleum products but are absent in coal tar were used to quantitatively allocate the source of the PAH contamination based on the relative ratio of the PAH to the biomarkers in soil samples. Using the resulting coal tar/petroleum source ratio the contribution of petroleum to the overall PAH contamination at the site was calculated. A multivariate statistical technique (principal component analysis or PCA) was used to provide an independent validation of the source allocation. The results of the source allocation provided a foundation for the site clean-up and remediation costs

Topical coal tar alone and in combination with oral methotrexate in management of psoriasis : a retrospective analysis

Directory of Open Access Journals (Sweden)

Prasad PVS

1997-01-01

Full Text Available Thirty five patients admitted with psoriasis were analysed. 16 patients received 20% crude coal tar and 19 patients received 20% crude coal tar along with methotrexate in a weekly oral schedule (15mg/wk. After 4 weeks of therapy there was total clearence in 52.6% of the patients with combination therapy, whereas only 12.5% of the patients with conventional therapy achieved this.

PAHs underfoot: contaminated dust from coal-tar sealcoated pavement is widespread in the United States

Energy Technology Data Exchange (ETDEWEB)

Peter C. Van Metre; Barbara J. Mahler; Jennifer T. Wilson [U.S. Geological Survey, Austin, TX (USA)

2009-01-15

We reported in 2005 that runoff from parking lots treated with coal-tar-based sealcoat was a major source of polycyclic aromatic hydrocarbons (PAHs) to streams in Austin, Texas. Here we present new data from nine U.S. cities that show nationwide patterns in concentrations of {Sigma}PAHs associated with sealcoat. Dust was swept from parking lots in six cities in the central and eastern U.S., where coal-tar-based sealcoat dominates use, and three cities in the western U.S., where asphalt-based sealcoat dominates use. For six central and eastern cities, median SPAH concentrations in dust from sealcoated and unsealcoated pavement are 2200 and 27 mg/kg, respectively. For three western cities, median SPAH concentrations in dust from sealcoated and unsealcoated pavement are similar and very low (2.1 and 0.8 mg/kg, respectively). Lakes in the central and eastern cities where pavement was sampled have bottom sediments with higher PAH concentrations than do those in the western cities relative to degree of urbanization. Bottom-sediment PAH assemblages are similar to those of sealcoated pavement dust regionally, implicating coal-tar-based sealcoat as a PAH source to the central and eastern lakes. Concentrations of benzo(a)pyrene in dust from coal-tar sealcoated pavement and adjacent soils greatly exceed generic soil screening levels, suggesting that research on human-health risk is warranted. 30 refs., 4 figs., 2 tabs.

Criteria for selection of dolomites and catalysts for tar elimination from biomass gasification gas. Kinetic constants

Energy Technology Data Exchange (ETDEWEB)

Corella, J; Narvaez, I; Orio, A [Madrid Univ. (Spain). Dept. of Chem. Eng.

1997-12-31

Calcined dolomites and commercial steam reforming catalysts are used downstream biomass gasifiers for hot catalytic raw gas cleaning. To further compare these solids under a rigorous basis, a reaction network and a kinetic model are presented. The apparent kinetic constant for the tar reduction is here proposed as a basis of comparison. Tar sampling and analysis, and the units used for the space-time in the catalytic reactor affect the kinetic constants observed. (author) (2 refs.)

Criteria for selection of dolomites and catalysts for tar elimination from biomass gasification gas. Kinetic constants

Energy Technology Data Exchange (ETDEWEB)

Corella, J.; Narvaez, I.; Orio, A. [Madrid Univ. (Spain). Dept. of Chem. Eng.

1996-12-31

Calcined dolomites and commercial steam reforming catalysts are used downstream biomass gasifiers for hot catalytic raw gas cleaning. To further compare these solids under a rigorous basis, a reaction network and a kinetic model are presented. The apparent kinetic constant for the tar reduction is here proposed as a basis of comparison. Tar sampling and analysis, and the units used for the space-time in the catalytic reactor affect the kinetic constants observed. (author) (2 refs.)

A proteomic study of TAR-RNA binding protein (TRBP-associated factors

Directory of Open Access Journals (Sweden)

Chi Ya-Hui

2011-02-01

Full Text Available Abstract Background The human TAR RNA-binding protein, TRBP, was first identified and cloned based on its high affinity binding to the small hairpin trans-activation responsive (TAR RNA of HIV-1. TRBP has more recently been found to be a constituent of the RNA-induced silencing complex (RISC serving as a Dicer co-factor in the processing of the ~70 nucleotide pre-microRNAs(miRNAs to 21-25 nucleotide mature miRNAs. Findings Using co-immunoprecipitation and protein-identification by mass spectrometry, we characterized intracellular proteins that complex with TRBP. These interacting proteins include those that have been described to act in protein synthesis, RNA modifications and processing, DNA transcription, and cell proliferation. Conclusions Our findings provide a proteome of factors that may cooperate with TRBP in activities such as miRNA processing and in RNA interference by the RISC complex.

Isolation of biosurfactant-producing bacteria from the Rancho La Brea Tar Pits.

Science.gov (United States)

Belcher, Richard W; Huynh, Kelvin V; Hoang, Timothy V; Crowley, David E

2012-12-01

This research was conducted to identify culturable surfactant-producing bacterial species that inhabit the 40,000-year-old natural asphalt seep at the Rancho La Brea Tar Pits in Los Angeles, CA. Using phenanthrene, monocyclic aromatic hydrocarbons, and tryptic soy broth as growth substrates, culturable bacteria from the tar pits yielded ten isolates, of which three species of gamma-proteobacteria produced biosurfactants that accumulated in spent culture medium. Partially purified biosurfactants produced by these strains lowered the surface tension of water from 70 to 35-55 mN/m and two of the biosurfactants produced 'dark halos' with the atomized oil assay, a phenomenon previously observed only with synthetic surfactants. Key findings include the isolation of culturable biosurfactant-producing bacteria that comprise a relatively small fraction of the petroleum-degrading community in the asphalt.

Phase-equilibria for design of coal-gasification processes: dew points of hot gases containing condensible tars. Final report

Energy Technology Data Exchange (ETDEWEB)

Prausnitz, J.M.

1980-05-01

This research is concerned with the fundamental physical chemistry and thermodynamics of condensation of tars (dew points) from the vapor phase at advanced temperatures and pressures. Fundamental quantitative understanding of dew points is important for rational design of heat exchangers to recover sensible heat from hot, tar-containing gases that are produced in coal gasification. This report includes essentially six contributions toward establishing the desired understanding: (1) Characterization of Coal Tars for Dew-Point Calculations; (2) Fugacity Coefficients for Dew-Point Calculations in Coal-Gasification Process Design; (3) Vapor Pressures of High-Molecular-Weight Hydrocarbons; (4) Estimation of Vapor Pressures of High-Boiling Fractions in Liquefied Fossil Fuels Containing Heteroatoms Nitrogen or Sulfur; and (5) Vapor Pressures of Heavy Liquid Hydrocarbons by a Group-Contribution Method.

Selected constituents in the smokes of foreign commercial cigaretts: tar, nicotine, carbon monoxide, and carbon dioxide

Energy Technology Data Exchange (ETDEWEB)

Jenkins, R.A.; Quincy, R.B.; Guerin, M.R.

1979-05-01

The tar, nicotine, carbon monoxide, and carbon dioxide contents of the smokes of 220 brands of foreign commercial cigarettes are reported. In some instances, filter cigarettes of certain brands were found to deliver as much or more smoke constituents than their nonfilter counterparts. Also, data indicated that there can be a great variation in the tar, nicotine, or carbon monoxide content of the smoke of samples of a given brand of cigarettes, depending on the nation in which they are purchased. 24 tables.

Effects of varying marijuana potency on deposition of tar and delta9-THC in the lung during smoking.

Science.gov (United States)

Matthias, P; Tashkin, D P; Marques-Magallanes, J A; Wilkins, J N; Simmons, M S

1997-12-01

To determine whether smoking more, compared to less, potent marijuana (MJ) cigarettes to a desired level of intoxication ("high") reduces pulmonary exposure to noxious smoke components, in 10 habitual smokers of MJ, we measured respiratory delivery and deposition of tar and delta9-tetrahydrocannabinol (THC), carboxyhemoglobin (COHb) boost, smoking topography, including cumulative puff volume (CPV) and breathholding time, change in heart rate (deltaHR) and "high" during ad lib smoking of 0, 1.77, and 3.95% MJ cigarettes on 3 separate days. At each session, subjects had access to only a single MJ cigarette. On average, smoking topography and COHb boost did not differ across the different strengths of MJ, while THC delivery, as well as HR, were significantly greater (p studies using a standardized smoking technique revealed a mean 25% lower tar yield from 3.95% than 1.77% MJ (p marijuana. Under the conditions of this study, we conclude that tar delivery is reduced relative to THC content in a minority of subjects, and this reduction appears to be due to a reduced intake of smoke (decreased CPV) and/or a reduced tar yield from the stronger MJ preparation.

Coal tar induces AHR-dependent skin barrier repair in atopic dermatitis

NARCIS (Netherlands)

Bogaard, E.H. van den; Bergboer, J.G.M.; Vonk-Bergers, M.; Vlijmen-Willems, I.M. van; Hato, S.V.; Valk, P.G. van der; Schroder, J.M.; Joosten, I.; Zeeuwen, P.L.J.M.; Schalkwijk, J.

2013-01-01

Topical application of coal tar is one of the oldest therapies for atopic dermatitis (AD), a T helper 2 (Th2) lymphocyte-mediated skin disease associated with loss-of-function mutations in the skin barrier gene, filaggrin (FLG). Despite its longstanding clinical use and efficacy, the molecular

A cost comparison of nuclear and fossil power for the Alberta tar sands

International Nuclear Information System (INIS)

Sochaski, R.O.; Smith, D.W.

1977-04-01

One technique envisaged for commercial development of the Alberta tar sands is in-situ removal of bitumen by injection of steam into the formation at high temperature and pressure. The 3000 MW of thermal power required for a typical 20 Gg/d plant could be supplied by a nuclear reactor. Accordingly, an economic comparison was made between a CANDU organic-cooled reactor and a conventional coal-fired station, using a variety of financial ground rules. This analysis shows that for debt-financed cases, nuclear power has essentially no economic competition from coal. For equity cases, the competitive position of a coal-fired station is heavily dependent on the cost of coal delivered to the tar sands area, discount rate, amortization period and inflation rate. (author)

Polycyclic aromatic hydrocarbons (PAHs) and hopanes in stranded tar-balls on the coasts of peninsular Malaysia: applications of biomarkers for identifying sources of oil pollution

International Nuclear Information System (INIS)

Zakaria, Mohamad Pauzi; Okuba, Tomoaki; Takada, Hideshige

2001-01-01

Malaysian coasts are subjected to various threats of petroleum pollution including routine and accidental oil spill from tankers, spillage of crude oils from inland and offshore oil fields, and run-off from land-based human activities. Due to its strategic location, the Straits of Malacca serves as a major shipping lane. This paper expands the utility of biomarker compounds, hopanes, in identifying the source of tar-balls stranded on Malaysian coasts. 20 tar-ball samples collected from the east and west coast were analysed for hopanes and polycylic aromatic hydrocarbons (PAHs). Four of the 13 tar-ball samples collected from the west coast of Peninsular Malaysia were identified as the Middle East crude oil (MECO) based on their biomarker signatures, suggesting tanker-derived sources significantly contributing the petroleum pollution in the Straits of Malacca. The tar-balls found on the east cost seem to originate from the offshore oil platforms in the South China Sea. The presence of South East Asian crude oil (SEACO) tar-balls on the west coast carry several plausible explanations. Some of the tar-balls could have been transported via sea currents from the east coast. The tankers carrying SEACO to other countries could have accidentally spilt the oil as well. Furthermore, discharge of tank washings and ballast water from the tankers were suggested based on the abundance in higher molecular weight n-alkanes and the absence of unresolved complex mixture (UCM) in the tar-ball samples. The other possibilities are that the tar-balls may have originated from the Sumatran oil fields and spillage of domestic oil from oil refineries in Port Dickson and Malacca. The results of PAHs analysis suggest that all the tar-ball samples have undergone various extent of weathering through evaporation, dissolution and photo-oxidation. (Author)

Polycyclic aromatic hydrocarbon (PAHs) and hopanes in stranded tar-balls on the coasts of Peninsular Malaysia: applications of biomarkers for identifying sources of oil pollution.

Science.gov (United States)

Zakaria, M P; Okuda, T; Takada, H

2001-12-01

Malaysian coasts are subjected to various threats of petroleum pollution including routine and accidental oil spill from tankers, spillage of crude oils from inland and off-shore oil fields, and run-off from land-based human activities. Due to its strategic location, the Straits of Malacca serves as a major shipping lane. This paper expands the utility of biomarker compounds, hopanes, in identifying the source of tar-balls stranded on Malaysian coasts. 20 tar-ball samples collected from the east and west coast were analyzed for hopanes and polycyclic aromatic hydrocarbons (PAHs). Four of the 13 tar-ball samples collected from the west coast of Peninsular Malaysia were identified as the Middle East crude oil (MECO) based on their biomarker signatures, suggesting tanker-derived sources significantly contributing the petroleum pollution in the Straits of Malacca. The tar-balls found on the east coast seem to originate from the offshore oil platforms in the South China Sea. The presence of South East Asian crude oil (SEACO) tar-balls on the west coast carry several plausible explanations. Some of the tar-balls could have been transported via sea currents from the east coast. The tankers carrying SEACO to other countries could have accidentally spilt the oil as well. Furthermore, discharge of tank washings and ballast water from the tankers were suggested based on the abundance in higher molecular weight n-alkanes and the absence of unresolved complex mixture (UCM) in the tar-ball samples. The other possibilities are that the tar-balls may have been originated from the Sumatran oil fields and spillage of domestic oil from oil refineries in Port Dickson and Malacca. The results of PAHs analysis suggest that all the tar-ball samples have undergone various extent of weathering through evaporation, dissolution and photooxidation.

Dissolution and transport of coal tar compounds in fractured clay-rich residuum

DEFF Research Database (Denmark)

Vulava, Vijay M.; McKay, Larry D.; Broholm, Mette Martina

2012-01-01

the importance of rapid dissolution and transport through the fracture networks. The concentrations continued to rise but did not reach the corresponding effective solubility limit in most cases. Compounds that were less soluble and those that were more susceptible to sorption or matrix diffusion eluted...... at a much slower rate. Analysis of contaminant concentrations in microcore residuum samples indicated that all 10 compounds had spread throughout the entire monolith and had diffused into the fine-grained matrix between fractures. These data suggest that the predominantly fine pore structure did not appear......We investigated the dissolution and transport of organic contaminants from a crude coal tar mixture in a monolith of fractured clay-rich residuum. An electrolyte solution was eluted through the residuum monolith containing a small emplaced source of coal tar under biologically inhibited and mildly...

A source mixing model to apportion PAHs from coal tar and asphalt binders in street pavements and urban aquatic sediments

Energy Technology Data Exchange (ETDEWEB)

Ahrens, M.J.; Depree, C.V. [National Institute of Water & Atmospheric Research, Hamilton (New Zealand)

2010-12-15

Present-day and more than 30 years old road and footpath pavements from Auckland, New Zealand were analysed for PAHs to test the hypothesis that coal tar based pavement binders contribute to unusually high PAH concentrations in adjacent stream and estuarine sediments Total PAH ({Sigma}{sub 28}PAH) concentrations in the dichloromethane-soluble fraction ('binder'), comprising 5-10% of pavement mass, were as high as 200 000 mg kg{sup -1}(10 000 mg kg{sup -1} in binder + aggregate) Older and deeper pavement layers were strongly pyrogenic, whereas pavement layers from recently sealed roads had a more petrogenic composition and more than 1000 times lower Sigma(28)PAH concentrations. Source identification analysis using three PAH isomer ratio pairs (benz(a)anthracene/(benz(a)anthracene + chrysene), benzo(a)pyrene/(benzo(a)pyrene + benzo(e)pyrene)), and indeno(1,2,3-cd)pyrene/(indeno(1,2,3-cd)pyrene + benzo(g,h,i)perylene) revealed low PAH (bitumen) pavements to have consistently lower isomer ratios than high PAH (coal tar) samples. A concentration-weighted mixing model, with coal tar and bitumen as source materials, explained more than 80% of the variance in isomer ratios and enveloped the entire PAH compositional and concentration range encountered PAH composition and concentrations in adjacent stream sediments ({gt} 15 mg kg{sup -1} dry weight) were consistent with diluted coal tar material as a principal PAH source. Due to the very high PAH concentrations of coal tar, a coal tar content of as little as 0.01% of total sediment mass can account for more than 90% of PAH concentrations in adjacent stream sediments.

Heating tar sands formations while controlling pressure

Science.gov (United States)

Stegemeier, George Leo [Houston, TX; Beer, Gary Lee [Houston, TX; Zhang, Etuan [Houston, TX

2010-01-12

Methods for treating a tar sands formation are described herein. Methods may include heating at least a section of a hydrocarbon layer in the formation from a plurality of heaters located in the formation. A pressure in the majority of the section may be maintained below a fracture pressure of the formation. The pressure in the majority of the section may be reduced to a selected pressure after the average temperature reaches a temperature that is above 240.degree. C. and is at or below pyrolysis temperatures of hydrocarbons in the section. At least some hydrocarbon fluids may be produced from the formation.

48 CFR 1201.301-70 - Amendment of (TAR) 48 CFR chapter 12.

Science.gov (United States)

2010-10-01

...) 48 CFR chapter 12 is maintained by the SPE through the TAR/TAM change process. This process consists... (C) To issue guidance which may be effective for a period of 1 year or less. (ii) Each TN will expire...

Tillering of Marandu palisadegrass maintained at fixed or variable heights throughout the year

Directory of Open Access Journals (Sweden)

Denis D. Pessoa

2016-05-01

Full Text Available Satisfactory tillering is the basic attribute to ensure stability and productivity of a grass population. We aimed to develop an understanding of tillering in Urochloa brizantha syn. Brachiaria brizantha cv. Marandu (Marandu palisadegrass maintained at constant or variable heights during the various seasons of the year and to identify defoliation strategies that optimize tillering. In an experiment conducted in Uberlândia, Minas Gerais, Brazil, 3 defoliation strategies were studied: sward kept at 30 cm during the whole year (constant height; kept at 15 cm in fall/winter, 30 cm in spring and 45 cm in summer (increasing height; and kept at 45 cm in fall/winter, 30 cm in spring and 15 cm in the summer (decreasing height. The experiment was completely randomized, with 4 replicates. The following variables were evaluated: tiller appearance (TAR, mortality (TMR and survival (TSR rates; the balance (BAL between TAR and TMR; tiller population stability (TPS; and number of tillers/m2 (NT. In winter and late spring, TAR and BAL were low, while in early spring, the sward with decreasing height showed high TAR, BAL and TPS. The NT was higher when managed with increasing height than with other height strategies. Lowering pasture height from 45 to 30 cm after the winter increased TAR in early spring. Grazing studies seem warranted to assess how these results can be reproduced under grazing and how pasture yield and quality plus animal performance compare with those under the fixed grazing height regimen. Keywords: Defoliation, grazing management, pasture height, tillers, Urochloa brizantha.DOI: 10.17138/TGFT(4101-111 Normal 0 false false false PT-BR X-NONE X-NONE

GC/MS analysis of coal tar composition produced from coal pyrolysis

African Journals Online (AJOL)

Coal tar is a significant product generated from coal pyrolysis. A detailed analytical study on its composition and chemical structure will be of great advantage to its further processing and utilization. Using a combined method of planigraphy-gas chromatograph/mass spectroscopy (GC/MS), this work presents a composition ...

Low Temperature Particle Filtration of Wood Gas with Low Tar Content

DEFF Research Database (Denmark)

Hindsgaul, Claus; Henriksen, Ulrik Birk; Bentzen, Jens Dall

2002-01-01

Baghouse filters and cartridge filters were tested online with wood gas from a two stage down draft gasifier. The gas contained soot and very low levels (10-30 mg/Nm³) of tar. Particle collection efficiencies were above 95%. Continuous operation with cheap self cleaning baghouse filters were test...

PR-PR: cross-platform laboratory automation system.

Science.gov (United States)

Linshiz, Gregory; Stawski, Nina; Goyal, Garima; Bi, Changhao; Poust, Sean; Sharma, Monica; Mutalik, Vivek; Keasling, Jay D; Hillson, Nathan J

2014-08-15

To enable protocol standardization, sharing, and efficient implementation across laboratory automation platforms, we have further developed the PR-PR open-source high-level biology-friendly robot programming language as a cross-platform laboratory automation system. Beyond liquid-handling robotics, PR-PR now supports microfluidic and microscopy platforms, as well as protocol translation into human languages, such as English. While the same set of basic PR-PR commands and features are available for each supported platform, the underlying optimization and translation modules vary from platform to platform. Here, we describe these further developments to PR-PR, and demonstrate the experimental implementation and validation of PR-PR protocols for combinatorial modified Golden Gate DNA assembly across liquid-handling robotic, microfluidic, and manual platforms. To further test PR-PR cross-platform performance, we then implement and assess PR-PR protocols for Kunkel DNA mutagenesis and hierarchical Gibson DNA assembly for microfluidic and manual platforms.

Acute toxicity of birch tar oil on aquatic organisms

Directory of Open Access Journals (Sweden)

M. HAGNER

2008-12-01

Full Text Available Birch tar oil (BTO is a by-product of processing birch wood in a pyrolysis system. Accumulating evidence suggests the suitability of BTO as a biocide or repellent in terrestrial environments for the control of weeds, insects, molluscs and rodents. Once applied as biocide, BTO may end up, either through run-off or leaching, in aquatic systems and may have adverse effects on non-target organisms. As very little is known about the toxicity of BTO to aquatic organisms, the present study investigated acute toxicity (LC50/EC50 of BTO for eight aquatic organisms. Bioassays with the Asellus aquaticus (crustacean, Lumbriculus variegatus (oligochaeta worm, Daphnia magna (crustacean, Lymnea sp. (mollusc, Lemna minor (vascular plant, Danio rerio (fish, Scenedesmus gracilis (algae, and Vibrio fischeri (bacterium were performed according to ISO, OECD or USEPA-guidelines. The results indicated that BTO was practically nontoxic to most aquatic organisms as the median effective BTO concentrations against most organisms were >150 mg L-1. In conclusion, our toxicity tests showed that aquatic organisms are to some extent, invariably sensitive to birch tar oil, but suggest that BTO does not pose a severe hazard to aquatic biota. We deduce that, unless BTOs are not applied in the immediate vicinity of water bodies, no special precaution is required.;

Identifying the source of tar balls deposited along the beaches of Goa in 2013 and comparing with historical data collected along the West Coast of India

Energy Technology Data Exchange (ETDEWEB)

Suneel, V., E-mail: vasimallas@nio.org [CSIR-National Institute of Oceanography, Dona Paula, Goa 403004 (India); Vethamony, P., E-mail: mony@nio.org [CSIR-National Institute of Oceanography, Dona Paula, Goa 403004 (India); Naik, B.G., E-mail: bgnaik@nio.org [CSIR-National Institute of Oceanography, Dona Paula, Goa 403004 (India); Krishna, M.S., E-mail: moturi@nio.org [CSIR-National Institute of Oceanography, Regional Centre, Visakhapatnam, 530 017 (India); Jadhav, Lakshmikant, E-mail: lakshya87.0@gmail.com [CSIR-National Institute of Oceanography, Dona Paula, Goa 403004 (India)

2015-09-15

Deposition of oil residues, also known as tar balls, is a seasonal phenomenon, and it occurs only in the southwest monsoon season along the west coast of India. This has become a serious environmental issue, as Goa is a global tourist destination. The present work aims at identifying the source oil of the tar balls that consistently depositing along the Goa coast using multi-marker fingerprint technique. In this context, the tar ball samples collected in May 2013 from 9 beaches of Goa coast and crude oils from different oil fields and grounded ship were subject to multi-marker analyses such as n-alkanes, pentacyclic terpanes, regular steranes, compound specific isotope analysis (CSIA) and principle component analysis (PCA). The n-alkane weathering index shows that samples have been weathered to various degrees, and the status of weathering is moderate. Since the international tanker route passes closer to the west coast of India (WCI), it is generally presumed that tanker wash is the source of the tar balls. We found that 2010/2011 tar balls are as tanker wash, but the present study demonstrates that the Bombay High (BH) oil fields can also contribute to oil contamination (tar balls) along ≈ 650 km stretch of the WCI, running from Gujarat in the north to Goa in the south. The simulated trajectories show that all the particles released in April traveled in the southeast direction, and by May, they reached the Goa coast with the influence of circulation of Indian monsoon system. - Highlights: • Multi-marker approach was effective in identifying the source of tar balls. • n-Alkane DRs show weathering effects even within the core of the tar ball. • Tar balls of the west coast of India since 2012 were derived from Bombay High crude. • Tanker-wash is not the only source of tar balls deposited on the beaches of Goa.

Identifying the source of tar balls deposited along the beaches of Goa in 2013 and comparing with historical data collected along the West Coast of India

International Nuclear Information System (INIS)

Suneel, V.; Vethamony, P.; Naik, B.G.; Krishna, M.S.; Jadhav, Lakshmikant

2015-01-01

Deposition of oil residues, also known as tar balls, is a seasonal phenomenon, and it occurs only in the southwest monsoon season along the west coast of India. This has become a serious environmental issue, as Goa is a global tourist destination. The present work aims at identifying the source oil of the tar balls that consistently depositing along the Goa coast using multi-marker fingerprint technique. In this context, the tar ball samples collected in May 2013 from 9 beaches of Goa coast and crude oils from different oil fields and grounded ship were subject to multi-marker analyses such as n-alkanes, pentacyclic terpanes, regular steranes, compound specific isotope analysis (CSIA) and principle component analysis (PCA). The n-alkane weathering index shows that samples have been weathered to various degrees, and the status of weathering is moderate. Since the international tanker route passes closer to the west coast of India (WCI), it is generally presumed that tanker wash is the source of the tar balls. We found that 2010/2011 tar balls are as tanker wash, but the present study demonstrates that the Bombay High (BH) oil fields can also contribute to oil contamination (tar balls) along ≈ 650 km stretch of the WCI, running from Gujarat in the north to Goa in the south. The simulated trajectories show that all the particles released in April traveled in the southeast direction, and by May, they reached the Goa coast with the influence of circulation of Indian monsoon system. - Highlights: • Multi-marker approach was effective in identifying the source of tar balls. • n-Alkane DRs show weathering effects even within the core of the tar ball. • Tar balls of the west coast of India since 2012 were derived from Bombay High crude. • Tanker-wash is not the only source of tar balls deposited on the beaches of Goa

Evaluation of different oxygen carriers for biomass tar reforming

DEFF Research Database (Denmark)

Mendiara, Teresa; Johansen, Joakim Myung; Utrilla, Rubén

2011-01-01

, in a concentration of 600–2000ppmv, was chosen as a tar model compound. Experiments were performed in a TGA apparatus and a fixed bed reactor. Four oxygen carriers (60% NiO/MgAl2O4 (Ni60), 40% NiO/NiAl2O4 (Ni40), 40% Mn3O4/Mg–ZrO2 (Mn40) and FeTiO3 (Fe)) were tested under alternating reducing/oxidizing cycles...

Cancer risk from incidental ingestion exposures to PAHs associated with coal-tar-sealed pavement

Science.gov (United States)

Williams, E. Spencer; Mahler, Barbara J.; Van Metre, Peter C.

2012-01-01

Recent (2009-10) studies documented significantly higher concentrations of polycyclic aromatic hydrocarbons (PAHs) in settled house dust in living spaces and soil adjacent to parking lots sealed with coal-tar-based products. To date, no studies have examined the potential human health effects of PAHs from these products in dust and soil. Here we present the results of an analysis of potential cancer risk associated with incidental ingestion exposures to PAHs in settings near coal-tar-sealed pavement. Exposures to benzo[a]pyrene equivalents were characterized across five scenarios. The central tendency estimate of excess cancer risk resulting from lifetime exposures to soil and dust from nondietary ingestion in these settings exceeded 1 × 10–4, as determined using deterministic and probabilistic methods. Soil was the primary driver of risk, but according to probabilistic calculations, reasonable maximum exposure to affected house dust in the first 6 years of life was sufficient to generate an estimated excess lifetime cancer risk of 6 × 10–5. Our results indicate that the presence of coal-tar-based pavement sealants is associated with significant increases in estimated excess lifetime cancer risk for nearby residents. Much of this calculated excess risk arises from exposures to PAHs in early childhood (i.e., 0–6 years of age).

Catalytic decomposition of biomass tars: Use of dolomite and untreated olivine

NARCIS (Netherlands)

Devi, L.; Ptasinski, K.J.; Janssen, F.J.J.G.; Paasen, van S.V.B.; Bergman, P.C.A.; Kiel, J.H.A.

2005-01-01

Although biomass is getting increased attention as a renewable energy source, one of the remaining problems still to be solved is the reduction of the high level of tar present in the product gas from gasification of biomass. The purpose of the present work is to study the activity of olivine and

Low Temperature Particle Filtration of Producer Gas with Low Tar Content

DEFF Research Database (Denmark)

Hindsgaul, Claus

This report describes the tests of different techniques for removing the particulates from producer gas from the 100 kW two-stage down-draft gasifier at DTU1 . The goal of the tests was to identify and implement methods to remove soot particles from producer gas with low tar content. During the f...

Trace metals in heavy crude oils and tar sand bitumens

Energy Technology Data Exchange (ETDEWEB)

Reynolds, J.G.

1990-11-28

Fe, Ni, and V are considered trace impurities in heavy crude oils and tar sand bitumens. In order to understand the importance of these metals, we have examined several properties: (1) bulk metals levels, (2) distribution in separated fractions, (3) size behavior in feeds and during processing, (4) speciation as a function of size, and (5) correlations with rheological properties. Some of the results of these studies show: (1) V and Ni have roughly bimodal size distributions, (2) groupings were seen based on location, size distribution, and Ni/V ratio of the sample, (3) Fe profiles are distinctively different, having a unimodal distribution with a maximum at relatively large molecular size, (4) Fe concentrations in the tar sand bitumens suggest possible fines solubilization in some cases, (5) SARA separated fractions show possible correlations of metals with asphaltene properties suggesting secondary and tertiary structure interactions, and (6) ICP-MS examination for soluble ultra-trace metal impurities show the possibility of unexpected elements such as U, Th, Mo, and others at concentrations in the ppB to ppM range. 39 refs., 13 figs., 5 tabs.

Polycyclic aromatic hydrocarbons (PAHs) in a coal tar standard reference material - SRM 1597a updated

Energy Technology Data Exchange (ETDEWEB)

Wise, Stephen A.; Poster, Dianne L.; Rimmer, Catherine A.; Schubert, Patricia; Sander, Lane C.; Schantz, Michele M. [National Institute of Standards and Technology (NIST), Analytical Chemistry Division, Gaithersburg, MD (United States); Leigh, Stefan D. [National Institute of Standards and Technology (NIST), Statistical Engineering Division, Gaithersburg, MD (United States); Moessner, Stephanie [National Institute of Standards and Technology (NIST), Analytical Chemistry Division, Gaithersburg, MD (United States); GMP/Comparator Labs, Werthenstein Chemie AG, Industrie Nord, Schachen (Switzerland)

2010-09-15

SRM 1597 Complex Mixture of Polycyclic Aromatic Hydrocarbons from Coal Tar, originally issued in 1987, was recently reanalyzed and reissued as SRM 1597a with 34 certified, 46 reference, and 12 information concentrations (as mass fractions) for polycyclic aromatic hydrocarbons (PAHs) and polycyclic aromatic sulfur heterocycles (PASHs) including methyl-substituted PAHs and PASHs. The certified and reference concentrations (as mass fractions) were based on results of analyses of the coal tar material using multiple analytical techniques including gas chromatography/mass spectrometry on four different stationary phases and reversed-phase liquid chromatography. SRM 1597a is currently the most extensively characterized SRM for PAHs and PASHs. (orig.)

Durability and regeneration of catalysts of the iron family in hydrogenation of low-temperature tar

Energy Technology Data Exchange (ETDEWEB)

Funasaka, W; Yokogawa, C; Hayashi, K; Kawamura, T; Fujita, H; Suga, S

1949-01-01

The low-temperature tar consisting of neutral and acidic oils has been reduced under atmospheric pressure between 400/sup 0/ and 500/sup 0/ by using catalysts prepared from Fe-Cr-kieselguhr, yellow ocher, and other material. When the reduction was performed at 480/sup 0/ with the yellow ocher from Niwasaka, Fukushima Prefacture, Japan, the low-temperature tar was easily converted to neutral and light oils and the catalysts could be regenerated by repeated baking and reduction. It is concluded that the commercialization of this reduction process is possible by using a cycle (each takes 20 minutes) composed of catalytic reaction, baking, and reduction of the catalysts.

Main component analysis of nuclear magnetic resonance /sup 1/H and /sup 13/C quantitative spectra of hydrogenation products of tars from Kansk-Achinsk Achinsk and Cheremkhovsk coals

Energy Technology Data Exchange (ETDEWEB)

Kushnarev, D.F.; Polonov, V.M.; Donskikh, V.I.; Rokhina, E.F.; Kalabin, G.A.

1986-03-01

Possibility is discussed of examining nuclear magnetic resonance /sup 1/H and /sup 13/C quantitative spectra of coal tar hydrogenation products using main component factorial analysis and applying special mathematical methods of processing experimental data. Nuclear magnetic resonance spectra of hydrogenation products of low temperature Cheremkhovsk coal carbonization tar and rapid pyrolysis Kansk-Achinsk coal tar were obtained on a WP-200SY (Bruker) spectrometer at 50.3 and 200.1 MHz, respectively. Data processing was carried out on an ODRA-1304 computer. Comparative correlation of parameters are given of tars and hydrogenation products which consist of hydrogenation of aromatic cycles and destruction of alkyl substituents, and factorial loads on structural parameters of tar hydrogenation products. 11 references.

Linear magnetic spring and spring/motor combination

Science.gov (United States)

Patt, Paul J. (Inventor); Stolfi, Fred R. (Inventor)

1991-01-01

A magnetic spring, or a spring and motor combination, providing a linear spring force characteristic in each direction from a neutral position, in which the spring action may occur for any desired coordinate of a typical orthogonal coordinate system. A set of magnets are disposed, preferably symmetrically about a coordinate axis, poled orthogonally to the desired force direction. A second set of magnets, respectively poled opposite the first set, are arranged on the sprung article. The magnets of one of the sets are spaced a greater distance apart than those of the other, such that an end magnet from each set forms a pair having preferably planar faces parallel to the direction of spring force, the faces being offset so that in a neutral position the outer edge of the closer spaced magnet set is aligned with the inner edge of the greater spaced magnet set. For use as a motor, a coil can be arranged with conductors orthogonal to both the magnet pole directions and the direction of desired spring force, located across from the magnets of one set and fixed with respect to the magnets of the other set. In a cylindrical coordinate system having axial spring force, the magnets are radially poled and motor coils are concentric with the cylinder axis.

The impact of steam and current density on carbon formation from biomass gasification tar on Ni/YSZ, and Ni/CGO solid oxide fuel cell anodes

Science.gov (United States)

Mermelstein, Joshua; Millan, Marcos; Brandon, Nigel

The combination of solid oxide fuel cells (SOFCs) and biomass gasification has the potential to become an attractive technology for the production of clean renewable energy. However the impact of tars, formed during biomass gasification, on the performance and durability of SOFC anodes has not been well established experimentally. This paper reports an experimental study on the mitigation of carbon formation arising from the exposure of the commonly used Ni/YSZ (yttria stabilized zirconia) and Ni/CGO (gadolinium-doped ceria) SOFC anodes to biomass gasification tars. Carbon formation and cell degradation was reduced through means of steam reforming of the tar over the nickel anode, and partial oxidation of benzene model tar via the transport of oxygen ions to the anode while operating the fuel cell under load. Thermodynamic calculations suggest that a threshold current density of 365 mA cm -2 was required to suppress carbon formation in dry conditions, which was consistent with the results of experiments conducted in this study. The importance of both anode microstructure and composition towards carbon deposition was seen in the comparison of Ni/YSZ and Ni/CGO anodes exposed to the biomass gasification tar. Under steam concentrations greater than the thermodynamic threshold for carbon deposition, Ni/YSZ anodes still exhibited cell degradation, as shown by increased polarization resistances, and carbon formation was seen using SEM imaging. Ni/CGO anodes were found to be more resilient to carbon formation than Ni/YSZ anodes, and displayed increased performance after each subsequent exposure to tar, likely due to continued reforming of condensed tar on the anode.

Groundwater flow cycling between a submarine spring and an inland fresh water spring.

Science.gov (United States)

Davis, J Hal; Verdi, Richard

2014-01-01

Spring Creek Springs and Wakulla Springs are large first magnitude springs that derive water from the Upper Floridan Aquifer. The submarine Spring Creek Springs are located in a marine estuary and Wakulla Springs are located 18 km inland. Wakulla Springs has had a consistent increase in flow from the 1930s to the present. This increase is probably due to the rising sea level, which puts additional pressure head on the submarine Spring Creek Springs, reducing its fresh water flow and increasing flows in Wakulla Springs. To improve understanding of the complex relations between these springs, flow and salinity data were collected from June 25, 2007 to June 30, 2010. The flow in Spring Creek Springs was most sensitive to rainfall and salt water intrusion, and the flow in Wakulla Springs was most sensitive to rainfall and the flow in Spring Creek Springs. Flows from the springs were found to be connected, and composed of three repeating phases in a karst spring flow cycle: Phase 1 occurred during low rainfall periods and was characterized by salt water backflow into the Spring Creek Springs caves. The higher density salt water blocked fresh water flow and resulted in a higher equivalent fresh water head in Spring Creek Springs than in Wakulla Springs. The blocked fresh water was diverted to Wakulla Springs, approximately doubling its flow. Phase 2 occurred when heavy rainfall resulted in temporarily high creek flows to nearby sinkholes that purged the salt water from the Spring Creek Springs caves. Phase 3 occurred after streams returned to base flow. The Spring Creek Springs caves retained a lower equivalent fresh water head than Wakulla Springs, causing them to flow large amounts of fresh water while Wakulla Springs flow was reduced by about half. Published 2013. This article is a U.S. Government work and is in the public domain in the USA.

Composition of phenols in the primary tar of bituminous brown coal of the Ukrainian S. S. R

Energy Technology Data Exchange (ETDEWEB)

Karavaev, N M; Fadeicheva, A G; Kuznetsov, V I

1957-01-01

The phenol content in the low-temperature carbonizatin tar of brown coal is higher than in high-temperature coking tar, and the tar obtained in the carbonization of briquets in the Pintsch ovens was investigated after its separation at the carbonization plant. The phenol-containing fraction was extracted with 13 percent NaOH. The phenols were fractionated into narrow fractions at 8- to 9-millimeter pressure, and the fractions were identified by their melting point, n, OH content, analysis, and the melting point of their arylglycolic acids. Lower phenols (44 percent) wre found in the crude-phenol fraction, including 6 percent of crystalline PhOH, melting point 34/sup 0/; o-C/sub 6/H/sub 4/(Me)OH, melting point 27/sup 0/; 9.25 percent m- and o-cresols, with 32 percent m-cresol in the mixture EtC/sub 6/H/sub 4/OH formed 4.5 percent of the crude phenols, and consisted of o-, m-, and p-ethylphenols, 1,4,2-, 1,3,4-, 1,3,5-, and 1,2,4-xylenols.

Gasification of Rice Husk in a Downdraft Gasifier: The Effect of Equivalence Ratio on the Gasification Performance, Properties, and Utilization Analysis of Byproducts of Char and Tar

Directory of Open Access Journals (Sweden)

Zhongqing Ma

2015-03-01

Full Text Available Rice husks (RH are a potential biomass source for bio-energy production in China, such as bio-gas production by gasification technology. In this paper, a bench-scale downdraft fixed bed gasifier (DFBG and a tar sampling system were designed. The effect of equivalence ratio (ER on gasification performance in terms of the temperature in the gasifier, the composition distribution of the producer gas, and the tar content in the producer gas was studied. The maximum lower heating value of 4.44 MJ/Nm3, minimum tar content of 1.34 g/Nm3, and maximum cold gas efficiency of 50.85% were obtained at ER of 0.211. In addition, the characteristics of gasification byproducts, namely bio-char and bio-tar, were analyzed. The proximate and ultimate analysis (especially of the alkali metal, the surface morphology, the surface area, and the pore size distribution of the rice husk char (RHC were obtained by the use of X-ray fluorescence (XRF and scanning electron microscopy (SEM, as well as by using the Brunauer-Emmett-Teller (BET method. The components of light tar and heavy tar were obtained by using gas chromatography-mass spectrometry (GC-MS.

Spring Tire

Science.gov (United States)

Asnani, Vivake M.; Benzing, Jim; Kish, Jim C.

2011-01-01

The spring tire is made from helical springs, requires no air or rubber, and consumes nearly zero energy. The tire design provides greater traction in sandy and/or rocky soil, can operate in microgravity and under harsh conditions (vastly varying temperatures), and is non-pneumatic. Like any tire, the spring tire is approximately a toroidal-shaped object intended to be mounted on a transportation wheel. Its basic function is also similar to a traditional tire, in that the spring tire contours to the surface on which it is driven to facilitate traction, and to reduce the transmission of vibration to the vehicle. The essential difference between other tires and the spring tire is the use of helical springs to support and/or distribute load. They are coiled wires that deform elastically under load with little energy loss.

Catalytic Pyrolysis of Tar Model Compound with Various Bio-Char Catalysts to Recycle Char from Biomass Pyrolysis

Directory of Open Access Journals (Sweden)

Jinmiao Liu

2016-03-01

Full Text Available Tar and char can be regarded as unwanted byproducts during the gasification process. In this study, three types of catalyst, i.e., biomass char (bio-char, nickel supported on biomass (Ni+bio-char, and nickel supported on bio-char (bio-char+Ni, were studied to compare the catalytic effects of different preparation methods on tar model compound removal. The structural characteristics of the three catalysts were also investigated by X-ray diffraction (XRD, scanning electron microscopy (SEM, and Brunauer-Emmett-Teller (BET methods. The results revealed that Ni+bio-char catalyst showed much higher activity for the reformation of toluene (C7H8 as a tar model compound than the other two catalysts. Toluene could be completely converted to small gas molecules at a conversion rate of 99.92% at 800 °C, and the maximum yield of gas was 432 mL/(mL C7H8. In particular, the H2 and CH4 yields were 339 and 85 mL/(mL C7H8 at 850 °C, respectively. An N2 absorption-desorption experiment demonstrated that the specific surface area of Ni+bio-char was 32.87 times that of bio-char and 8.39 times that of bio-char+Ni. Moreover, metallic nickel (Ni0 particles could be generated in the carbon matrix of Ni+bio-char catalyst. SEM analysis confirmed that the Ni+bio-char catalyst had a more porous structure. Nickel supported on biomass might be a promising catalyst for tar reformation because of its excellent catalytic activities.

Studying Springs in Series Using a Single Spring

Science.gov (United States)

Serna, Juan D.; Joshi, Amitabh

2011-01-01

Springs are used for a wide range of applications in physics and engineering. Possibly, one of their most common uses is to study the nature of restoring forces in oscillatory systems. While experiments that verify Hooke's law using springs are abundant in the physics literature, those that explore the combination of several springs together are…

Epoxy-borax-coal tar composition for a radiation protective, burn resistant drum liner and centrifugal casting method

International Nuclear Information System (INIS)

Boyer, N.W.; Taylor, R.S.

1980-01-01

A boron containing burn resistant, low level radiation protection material useful, for example, as a liner for radioactive waste disposal and storage, a component for neutron absorber, and a shield for a neutron source. The material is basically composed of borax in the range of 25-50%, coal tar in the range of 25-37.5%, with the remainder being an epoxy resin mix. A preferred composition is 50% borax, 25% coal tar and 25% epoxy resin. The material is not susceptible to burning and is about 1/5 the cost of existing radiation protection material utilized in similar applications

Síndrome de TAR y estado de heterocigosis para anemia falciforme

Directory of Open Access Journals (Sweden)

Pilar Garavito

2004-01-01

Full Text Available Presentación de un paciente con el cuadro clínico del síndrome de TAR, quien presenta además un estado de heterocigosis para anemia falciforme. El síndrome de TAR, descrito por primera vez en 1959 por Shaw y Oliver, es un trastorno genético no común que ocurre con una prevalencia aproximada de 1: 500.000 a 1: 1.000.000 de nacidos vivos. En 1969 Hall y col. delinearon los criterios diagnósticos de este síndrome que incluyen ausencia bilateral del radio con presencia de ambos pulgares y trombocitopenia. Otras anomalías descritas en menor frecuencia son: Alteraciones óseas del húmero y cúbito, en los casos severos, focomelia, malformaciones de expresión variable en extremidades inferiores, malformaciones cardiacas e intolerancia a la leche de vaca (1, 2. Los hallazgos encontrados en este caso se comparan con los de la literatura y se discute su posible etiología, además de resaltar la importancia de realizar un diagnóstico y tratamiento precoz y preciso especialmente de la trombocitopenia

Physical properties and component contents of brown coal tars obtained in semicoking with a solid heat transfer semicoke

Energy Technology Data Exchange (ETDEWEB)

Kuznetsov, V I; Bobrova, A A

1955-01-01

Tar obtained in low-temperature carbonization of brown coals with brown-coal semicoke as a heat-transfer medium contains more water and dust, has a lower drop point, and a higher specific gravity, and contains more asphaltene and less paraffin than does tar from the same coal produced in rotating retorts or in shaft kilns. The brown-coal semicoke used as a heat-transfer medium produces partial thermal cracking of the fuel and polymerization of the products of secondary decompositions. The yield of asphaltenes is lowered when the carbonization temperature is raised.

Structural determinants of HIV-1 nucleocapsid protein for cTAR DNA binding and destabilization, and correlation with inhibition of self-primed DNA synthesis.

Science.gov (United States)

Beltz, Hervé; Clauss, Céline; Piémont, Etienne; Ficheux, Damien; Gorelick, Robert J; Roques, Bernard; Gabus, Caroline; Darlix, Jean-Luc; de Rocquigny, Hugues; Mély, Yves

2005-05-20

The nucleocapsid protein (NC) of human immunodeficiency virus type 1 (HIV-1) is formed of two highly conserved CCHC zinc fingers flanked by small basic domains. NC is required for the two obligatory strand transfers in viral DNA synthesis through its nucleic acid chaperoning properties. The first DNA strand transfer relies on NC's ability to bind and destabilize the secondary structure of complementary transactivation response region (cTAR) DNA, to inhibit self-priming, and to promote the annealing of cTAR to TAR RNA. To further investigate NC chaperone properties, our aim was to identify by fluorescence spectroscopy and gel electrophoresis, the NC structural determinants for cTAR binding and destabilization, and for the inhibition of self-primed DNA synthesis on a model system using a series of NC mutants and HIV-1 reverse transcriptase. NC destabilization and self-priming inhibition properties were found to be supported by the two fingers in their proper context and the basic (29)RAPRKKG(35) linker. The strict requirement of the native proximal finger suggests that its hydrophobic platform (Val13, Phe16, Thr24 and Ala25) is crucial for binding, destabilization and inhibition of self-priming. In contrast, only partial folding of the distal finger is required, probably for presenting the Trp37 residue in an appropriate orientation. Also, Trp37 and the hydrophobic residues of the proximal finger appear to be essential for the propagation of the melting from the cTAR ends up to the middle of the stem. Finally, both N-terminal and C-terminal basic domains contribute to cTAR binding but not to its destabilization.

Beginning Spring

CERN Document Server

Caliskan, Mert

2015-01-01

Get up to speed quickly with this comprehensive guide toSpring Beginning Spring is the complete beginner's guide toJava's most popular framework. Written with an eye towardreal-world enterprises, the book covers all aspects of applicationdevelopment within the Spring Framework. Extensive samples withineach chapter allow developers to get up to speed quickly byproviding concrete references for experimentation, building askillset that drives successful application development byexploiting the full capabilities of Java's latest advances. Spring provides the exact toolset required to build anent

Co-carcinogenesis: Human Papillomaviruses, Coal Tar Derivatives, and Squamous Cell Cervical Cancer

Directory of Open Access Journals (Sweden)

Harry W. Haverkos

2017-11-01

Full Text Available Cervical cancer (CC is the fourth most common cancers among women worldwide. Human papillomaviruses (HPVs play a major role in the etiology of CC, with several lines of epidemiologic and experimental evidence supporting a role for non-viral (co-carcinogens and host genetic factors in controlling the risk for progression to neoplasia among HPV-infected individuals. The role of co-carcinogens in the development of CC is significant in the developing world where poor sanitation and other socio-economic conditions increase the infectious cancer burden. Here, we discuss how exposure to environmental factors such as coal tar derivatives from cigarette smoking, tar-based sanitary products, and inhaled smoke from biomass-burning stoves, could activate host pathways involved in development of HPV-associated squamous cell cancers in resource-limited settings. Understanding interactions between these pathways with certain oncogenic HPV genotypes may guide implementation of strategies for control and treatment of HPV-associated cancers that develop in populations at high risk of exposure to various co-carcinogens.

The migration and monitoring of viscous NAPLs (coal tar and creosote) in the subsurface

Energy Technology Data Exchange (ETDEWEB)

Jackson, R. [Intera Engineering Ltd., Heidelberg, ON (Canada)

2009-07-01

The high viscosity of nonaqueous phase liquids (NAPLs) such as creosote and coal tar complicates efforts to monitor their mobility at contaminated sites. Viscous NAPLs can remain mobile for many decades after their application as a wood preservative, or after the closure of the facilities in which they were generated. NAPL-wet pathways in the subsurface can also lead to errors in residual saturation measurements. This abstract discussed issues related to creeping flow and the low seepage rates that are not accounted for using traditional measuring methods. Examples of creeping flow and the monitoring techniques used to assess it were presented for sites in British Columbia and Florida. The drainage of viscous NAPLs during water table declines was also considered, and a case study of a coal tar-removal procedures using polymer surfactant flooding was presented.

Forensic assessment of polycyclic aromatic hydrocarbons at the former Sydney Tar Ponds and surrounding environment using fingerprint techniques

International Nuclear Information System (INIS)

MacAskill, N. Devin; Walker, Tony R.; Oakes, Ken; Walsh, Margaret

2016-01-01

Polycyclic aromatic hydrocarbons (PAHs) were assessed spatially and temporally within and adjacent to a former coking and steel manufacturing facility in Sydney, Nova Scotia, Canada. Concentrations of PAHs were measured in surface soils, marine and estuary sediments prior to and during remediation of the Sydney Tar Ponds (STPs) site which was contaminated by nearly a century of coking and steel production. Previous studies identified PAHs in surficial marine sediments within Sydney Harbour, which were considered to be derived from STP discharges. Numerous PAH fingerprint techniques (diagnostic ratios, principal component analysis, quantitative and qualitative analysis) were applied to soil and sediment samples from the STPs and surrounding area to identify common source apportionment of PAHs. Results indicate coal combustion (from historical residential, commercial and industrial uses) and coal handling (from historic on-site stockpiling and current coal transfer and shipment facilities) are likely the principal source of PAHs found in urban soils and marine sediments, consistent with current and historical activities near these sites. However, PAH fingerprints associated with STP sediments correlated poorly with those of urban soils and marine sediments, but were similar to coal tar, historically consistent with by-products produced by the former coking operations. This study suggests PAH contamination of Sydney Harbour sediments and urban soils is largely unrelated to historic coking operations or recent remediation of the STPs site, but rather a legacy of extensive use of coal for a variety of activities. - Highlights: • PAHs were measured in soils and sediments near a former coking and steel facility. • Previous studies identified tar residues as main source of PAHs in marine sediments. • PAH fingerprint techniques were used to identify common source apportionment. • Fingerprint techniques indicated common sources derived from coal, not tar residues

Microscopic charcoal and tar (CHAT particles in peat: a 6500-year record of palaeo-fires in southern Sweden

Directory of Open Access Journals (Sweden)

B.A. Malmgren

2012-01-01

Full Text Available Peat stratigraphies of eleven raised bogs in southern Sweden were investigated. Measurements included the occurrence of charcoal and various tar particles. Most of the particles found were microscopic, i.e. 5–100 µm in diameter. Two distinctly different groups of particles were distinguished: (A charred fragments of plant tissue and (B objects formed from tar, which were classified into five sub-groups on the basis of morphology. Both charcoal and tar are indicative of mire and forest fires. We suggest that it is possible to use the different groups of particles as fire regime indicators. Hence, the high frequency of charcoal and tar (CHAT in the lower parts of the stratigraphies, i.e. in the lower strongly decomposed fen and carr peats that were formed before ca. 4000 cal 14C BP, could be indicative of intense and frequent local fires. The decreasing abundance of CHAT and the lower relative share of Type A particles within the lower strongly decomposed Sphagnum peat ca. 4000–2500 cal 14C BP signify a transition from local to regional fires. With a few exceptions, the uppermost weakly decomposed ombrotrophic peats formed after ca. 2500 cal 14C BP, in which both charcoal and tar are rare, indicate a period of low fire frequency at both local and regional scales. There is no regional variation in the lower material, and it seems that wildfires were common phenomena throughout southern Sweden during the first few thousand years after peat formation began 6–8000 years ago. From a climatological point of view, the mass occurrence of CHAT in the lower parts of the profiles indicates a warm and dry Mid Holocene with frequent and widespread wildfires, and a moist and cool Late Holocene with more sporadic fires. Spectral analysis of the entire dataset shows significant periodicities of 610, 70, 30, 21, 17 and 14 years, the two most significant being 14 and 70 years.

Formulation of Pine Tar Antidandruff Shampoo Assessment and Comparison With Some Commercial Formulations

Directory of Open Access Journals (Sweden)

M. Gharavi

1990-07-01

Full Text Available In this study a pine tar shampoo as a new antidandruff formulation is presented. Assessment of antidandruff preparations has been hampered by the lack of standardized schedules, and reliable methods of evaluation.Some antidandruff agents such as : Zinc pyri-thione pine tar, selenium sulphide and (sulfure were used in shampoos. Samples were coded as numbers 1,2 formulated by us and 3,4 formulated commercially. The grading scheme based on 10 point scale, and corneocyte count was carried out on 50 selected volunte¬ers. Corneocyte count and fungal study proved that pine tor shampoo is effective against pityrosporum ovale. Draize lest was used for determination of the irritancy potential of the samples. Results showed that samples numbered 1,2 were relatively innocous in comparison with the others. I urthermore,s kin sensitination test on rabbit also confirmed the results obtained by Draize test. Consumer judgments proved that all formulations were acceptable.

Coal-tar-based sealcoated pavement: a major PAH source to urban stream sediments.

Science.gov (United States)

Witter, Amy E; Nguyen, Minh H; Baidar, Sunil; Sak, Peter B

2014-02-01

We used land-use analysis, PAH concentrations and assemblages, and multivariate statistics to identify sediment PAH sources in a small (~1303 km(2)) urbanizing watershed located in South-Central, Pennsylvania, USA. A geographic information system (GIS) was employed to quantify land-use features that may serve as PAH sources. Urban PAH concentrations were three times higher than rural levels, and were significantly and highly correlated with combined residential/commercial/industrial land use. Principal components analysis (PCA) was used to group sediments with similar PAH assemblages, and correlation analysis compared PAH sediment assemblages to common PAH sources. The strongest correlations were observed between rural sediments (n = 7) and coke-oven emissions sources (r = 0.69-0.78, n = 5), and between urban sediments (n = 22) and coal-tar-based sealcoat dust (r = 0.94, n = 47) suggesting that coal-tar-based sealcoat is an important urban PAH source in this watershed linked to residential and commercial/industrial land use. Copyright © 2013 Elsevier Ltd. All rights reserved.

Coal-tar-based pavement sealcoat, polycyclic aromatic Hydrocarbons (PAHs), and environmental health

Science.gov (United States)

Mahler, B.J.; Van Metre, P.C.

2011-01-01

Studies by the U.S. Geological Survey (USGS) have identified coal-tar-based sealcoat-the black, viscous liquid sprayed or painted on asphalt pavement such as parking lots-as a major source of polycyclic aromatic hydrocarbon (PAH) contamination in urban areas for large parts of the Nation. Several PAHs are suspected human carcinogens and are toxic to aquatic life.

The influence of partial oxidation mechanisms on tar destruction in TwoStage biomass gasification

DEFF Research Database (Denmark)

Ahrenfeldt, Jesper; Egsgaard, Helge; Stelte, Wolfgang

2013-01-01

adsorption and determined by stable isotope dilution analysis. The results have shown that partial oxidation reduces and converts primary tars into low molecular weight, polycyclic aromatic hydrocarbons (PAHs), primarily naphthalene. At temperatures above 950°C practically all phenol is converted...

Inhibition of HIV Replication by Cyclic and Hairpin PNAs Targeting the HIV-1 TAR RNA Loop

Science.gov (United States)

Upert, Gregory; Di Giorgio, Audrey; Upadhyay, Alok; Manvar, Dinesh; Pandey, Nootan; Pandey, Virendra N.; Patino, Nadia

2012-01-01

Human immunodeficiency virus-1 (HIV-1) replication and gene expression entails specific interaction of the viral protein Tat with its transactivation responsive element (TAR), to form a highly stable stem-bulge-loop structure. Previously, we described triphenylphosphonium (TPP) cation-based vectors that efficiently deliver nucleotide analogs (PNAs) into the cytoplasm of cells. In particular, we showed that the TPP conjugate of a linear 16-mer PNA targeting the apical stem-loop region of TAR impedes Tat-mediated transactivation of the HIV-1 LTR in vitro and also in cell culture systems. In this communication, we conjugated TPP to cyclic and hairpin PNAs targeting the loop region of HIV-1 TAR and evaluated their antiviral efficacy in a cell culture system. We found that TPP-cyclic PNAs containing only 8 residues, showed higher antiviral potency compared to hairpin PNAs of 12 or 16 residues. We further noted that the TPP-conjugates of the 8-mer cyclic PNA as well as the 16-mer linear PNA displayed similar antiviral efficacy. However, cyclic PNAs were shown to be highly specific to their target sequences. This communication emphasizes on the importance of small constrained cyclic PNAs over both linear and hairpin structures for targeting biologically relevant RNA hairpins. PMID:23029603

Inhibition of HIV Replication by Cyclic and Hairpin PNAs Targeting the HIV-1 TAR RNA Loop

Directory of Open Access Journals (Sweden)

Gregory Upert

2012-01-01

Full Text Available Human immunodeficiency virus-1 (HIV-1 replication and gene expression entails specific interaction of the viral protein Tat with its transactivation responsive element (TAR, to form a highly stable stem-bulge-loop structure. Previously, we described triphenylphosphonium (TPP cation-based vectors that efficiently deliver nucleotide analogs (PNAs into the cytoplasm of cells. In particular, we showed that the TPP conjugate of a linear 16-mer PNA targeting the apical stem-loop region of TAR impedes Tat-mediated transactivation of the HIV-1 LTR in vitro and also in cell culture systems. In this communication, we conjugated TPP to cyclic and hairpin PNAs targeting the loop region of HIV-1 TAR and evaluated their antiviral efficacy in a cell culture system. We found that TPP-cyclic PNAs containing only 8 residues, showed higher antiviral potency compared to hairpin PNAs of 12 or 16 residues. We further noted that the TPP-conjugates of the 8-mer cyclic PNA as well as the 16-mer linear PNA displayed similar antiviral efficacy. However, cyclic PNAs were shown to be highly specific to their target sequences. This communication emphasizes on the importance of small constrained cyclic PNAs over both linear and hairpin structures for targeting biologically relevant RNA hairpins.

A real-time view of the TAR:Tat:P-TEFb complex at HIV-1 transcription sites

Directory of Open Access Journals (Sweden)

Knezevich Anna

2007-05-01

Full Text Available Abstract HIV-1 transcription is tightly regulated: silent in long-term latency and highly active in acutely-infected cells. Transcription is activated by the viral protein Tat, which recruits the elongation factor P-TEFb by binding the TAR sequence present in nascent HIV-1 RNAs. In this study, we analyzed the dynamic of the TAR:Tat:P-TEFb complex in living cells, by performing FRAP experiments at HIV-1 transcription sites. Our results indicate that a large fraction of Tat present at these sites is recruited by Cyclin T1. We found that in the presence of Tat, Cdk9 remained bound to nascent HIV-1 RNAs for 71s. In contrast, when transcription was activated by PMA/ionomycin, in the absence of Tat, Cdk9 turned-over rapidly and resided on the HIV-1 promoter for only 11s. Thus, the mechanism of trans-activation determines the residency time of P-TEFb at the HIV-1 gene, possibly explaining why Tat is such a potent transcriptional activator. In addition, we observed that Tat occupied HIV-1 transcription sites for 55s, suggesting that the TAR:Tat:P-TEFb complex dissociates from the polymerase following transcription initiation, and undergoes subsequent cycles of association/dissociation.

Just Spring

CERN Document Server

Konda, Madhusudhan

2011-01-01

Get a concise introduction to Spring, the increasingly popular open source framework for building lightweight enterprise applications on the Java platform. This example-driven book for Java developers delves into the framework's basic features, as well as advanced concepts such as containers. You'll learn how Spring makes Java Messaging Service easier to work with, and how its support for Hibernate helps you work with data persistence and retrieval. Throughout Just Spring, you'll get your hands deep into sample code, beginning with a problem that illustrates dependency injection, Spring's co

Structural evolution of Eucalyptus tar pitch-based carbons during carbonization

International Nuclear Information System (INIS)

Prauchner, Marcos J.; Pasa, Vanya M.D.; Molhallem, Nelcy D.S.; Otani, Choyu; Otani, Satika; Pardini, Luiz C.

2005-01-01

Wood tar pitches are generated as by-products by the charcoal manufacturing industry. They have a macromolecular structure constituted mainly by phenolic, guaiacylic, and siringylic units common to lignin. Due to their characteristics, biopitches are been investigated as precursors of carbon materials such as carbon fibers, bioelectrodes and activated carbons. In the present work the structural evolution of Eucalyptus tar pitches under carbonization is investigated, which is important for the improvement of planning and control of pitch processing and end-product properties during carbon material production. The studies involve X-ray diffraction and infrared analyses, besides helium density, BET surface area and BJH pore volume measurements. The results showed that the conversion of pitch into carbon basically involves three steps: (1) Up to around 600 deg C the material has an highly disordered structure, being the release of aliphatic side chains and volatiles the main events taking place. (2) Between 600 deg C and 800 deg C, condensation of aromatic rings occurs to form bi-dimensional hexagonal networks so that micro- and mesoporosity are developed. The 800 deg C-coke is constituted by two phases: one highly disordered and another more crystalline. (3) Over 800 deg C, both phases are gradually ordered. As defects are gradually removed, surface area and porosity decrease, approaching zero for the 2100 deg C-coke

Aromatic oxygen compounds boiling from 180/sup 0/ to 225/sup 0/ from acid oils in low-temperature tar

Energy Technology Data Exchange (ETDEWEB)

Jaeger, A; Kattwinkel, G

1950-01-01

To determine the composition of the Krupp-Lurgi low-temperature coal tar and to develop methods for isolating the various compounds, a quantitative investigation was made of the dry tar acid mixture. The aromatic O compounds boiling up to 225/sup 0/ were secured by fractionation with one of the several columns that are described. Large volumes of tar were fractionated under vacuum in an apparatus with a 10-liter flask, electrically heated, and provided with a fractionating column (packed) with a jacket supplied by recirculated oil, externally heated. Large volumes were fractionated to give sufficient quantities of the O compounds. The method of fractional extraction, not described herein, made the separation of the acid oils by fractional distillation much easier. The aromatic O compounds present in greatest proportion are relatively easily isolated; those present in small quantities and more difficult to separate can be removed as a mixture, which can be hydrogenated directly to solvents. Phenols and cresols are formed in about equal fractions in low-temperature carbonization. Of the various xylenols, the sym-xylenol is present to the greatest extent. O compounds with longer side chains than C/sub 2/ were present only to a very slight extent. At the temperature of formation of these tars, side chains of three or more C atoms formed closed ring compounds (indan derivatives, etc.). Little change appears to occur up to 225/sup 0/ in the fractionation of these acid oils.

The effects of topical corticosteroids and a coal tar preparation on dithranol-induced irritation in patients with psoriasis

Energy Technology Data Exchange (ETDEWEB)

Swinkels, O.Q.J.; Kucharekova, M.; Prins, M.; Gerritsen, M.J.P.; van der Valk, P.G.M.; van de Kerkhof, P.C.M. [University of Nijmegen, Nijmegen (Netherlands). Medical Center

2003-02-01

Dithranol has been a mainstay in the treatment of psoriasis for more than 80 years. Although a safe approach, the irritation of the clinically uninvolved perilesional skin remains a major limitation of this treatment. Corticosteroids and coal tar solution have an anti-inflammatory potential. The aim of the present study was to investigate the clinical and cell-biological effects of two topical corticosteroids and a coal tar preparation on dithranol-irritated skin. The expression of epidermal proliferation, differentiation and inflammation markers and the clinical irritation scores indicate that the application of a high potency corticosteroid is the best approach to minimise dithranol irritation.

Catalytic steam reforming of tar derived from steam gasification of sunflower stalk over ethylene glycol assisting prepared Ni/MCM-41

International Nuclear Information System (INIS)

Karnjanakom, Surachai; Guan, Guoqing; Asep, Bayu; Du, Xiao; Hao, Xiaogang; Samart, Chanatip; Abudula, Abuliti

2015-01-01

Highlights: • Ni/MCM-41 was prepared by EG-assisted co-impregnation method. • EG-assisted co-impregnation method resulted in Ni particles well dispersed on MCM-41. • Ni/MCM-41-EG catalyst had high catalytic activity for tar reforming. • The highest H 2 gas yield was obtained when using 20 wt.% Ni/MCM-41-EG. • The catalysts were reused up to 5 cycles without any serious deactivation. - Abstract: Ethylene glycol (EG) assisted impregnation of nickel catalyst on MCM-41 (Ni/MCM-41-EG) was performed and applied for steam reforming of tar derived from biomass. The catalyst was characterized by SEM–EDX, BET, XRD, and TPR. It is found that smaller nickel particles were well dispersed on MCM-41 and better catalytic activity was shown for the Ni/MCM-41-EG when compared with the catalyst of Ni/MCM-41 prepared by using the conventional impregnation method. H 2 yield increased approximately 8% when using 20 wt.% Ni/MCM-41-EG instead of 20 wt.% Ni/MCM-41 for the steam reforming of tar derived from sunflower stalk. The catalyst reusability was also tested up to five cycles, and no obvious activity reduction was observed. It indicates that EG assisted impregnation method is a good way to prepare metal loaded porous catalyst with high catalytic activity, high loading amount and long-term stability for the tar reforming

Tar in road system wastes - bibliographic study - quick characterization methods; Le goudron dans les dechets du reseau routier - etude bibliographique - methodes de caracterisation rapides

Energy Technology Data Exchange (ETDEWEB)

Brazillet, C.; Domas, J.; Pepin, G.

2001-12-15

In the framework of the european regulations on the wastes management, the road structure wastes present a particularly problem because of the tar content and of the toxic associated polycyclic aromatic hydrocarbons. In order to chose the elimination or the valorization of these roads wastes, it is necessary to measure the tar content. After a presentation of the study objectives, a bibliographic study of the context, the challenges, the hydrocarbons, the tar characterization and the today situation of the french road network, the author presents the methods of PAH detection with a special attention on the well known methods: the PAK marker, the TSE and the toluene spot. (A.L.B.)

Biogeochemical gradients above a coal tar DNAPL

Energy Technology Data Exchange (ETDEWEB)

Scherr, Kerstin E., E-mail: kerstin.brandstaetter-scherr@boku.ac.at [University of Natural Resources and Life Sciences Vienna (BOKU), Department IFA-Tulln, Institute for Environmental Biotechnology, Konrad Lorenz Strasse 20, 3430 Tulln (Austria); Backes, Diana [University of Natural Resources and Life Sciences Vienna (BOKU), Department IFA-Tulln, Institute for Environmental Biotechnology, Konrad Lorenz Strasse 20, 3430 Tulln (Austria); Scarlett, Alan G. [University of Plymouth, Petroleum and Environmental Geochemistry Group, Biogeochemistry Research Centre, Drake Circus, Plymouth, Devon PL4 8AA (United Kingdom); Lantschbauer, Wolfgang [Government of Upper Austria, Directorate for Environment and Water Management, Division for Environmental Protection, Kärntner Strasse 10-12, 4021 Linz (Austria); Nahold, Manfred [GUT Gruppe Umwelt und Technik GmbH, Ingenieurbüro für Technischen Umweltschutz, Plesching 15, 4040 Linz (Austria)

2016-09-01

Naturally occurring distribution and attenuation processes can keep hydrocarbon emissions from dense non aqueous phase liquids (DNAPL) into the adjacent groundwater at a minimum. In a historically coal tar DNAPL-impacted site, the de facto absence of a plume sparked investigations regarding the character of natural attenuation and DNAPL resolubilization processes at the site. Steep vertical gradients of polycyclic aromatic hydrocarbons, microbial community composition, secondary water quality and redox-parameters were found to occur between the DNAPL-proximal and shallow waters. While methanogenic and mixed-electron acceptor conditions prevailed close to the DNAPL, aerobic conditions and very low dissolved contaminant concentrations were identified in three meters vertical distance from the phase. Comprehensive two-dimensional gas chromatography–mass spectrometry (GC × GC–MS) proved to be an efficient tool to characterize the behavior of the present complex contaminant mixture. Medium to low bioavailability of ferric iron and manganese oxides of aquifer samples was detected via incubation with Shewanella alga and evidence for iron and manganese reduction was collected. In contrast, 16S rDNA phylogenetic analysis revealed the absence of common iron reducing bacteria. Aerobic hydrocarbon degraders were abundant in shallow horizons, while nitrate reducers were dominating in deeper aquifer regions, in addition to a low relative abundance of methanogenic archaea. Partial Least Squares – Canonical Correspondence Analysis (PLS-CCA) suggested that nitrate and oxygen concentrations had the greatest impact on aquifer community structure in on- and offsite wells, which had a similarly high biodiversity (H’ and Chao1). Overall, slow hydrocarbon dissolution from the DNAPL appears to dominate natural attenuation processes. This site may serve as a model for developing legal and technical strategies for the treatment of DNAPL-impacted sites where contaminant plumes are

Pro Spring Batch

CERN Document Server

Minella, Michael T

2011-01-01

Since its release, Spring Framework has transformed virtually every aspect of Java development including web applications, security, aspect-oriented programming, persistence, and messaging. Spring Batch, one of its newer additions, now brings the same familiar Spring idioms to batch processing. Spring Batch addresses the needs of any batch process, from the complex calculations performed in the biggest financial institutions to simple data migrations that occur with many software development projects. Pro Spring Batch is intended to answer three questions: *What? What is batch processing? What

Preparation, Characterization, and Activation of Co-Mo/Y Zeolite Catalyst for Coal Tar Conversion to Liquid Fuel

Directory of Open Access Journals (Sweden)

Didi Dwi Anggoro

2017-05-01

Full Text Available One of many efforts to convert coal tar into alternative liquid fuel is by hydrocracking. This research aims to determine the impregnation of Co-Mo/Y zeolite, its characteristics, the effect of impregnation temperature and time, and also the best Co-Mo/Y zeolite impregnation condition for the conversion of coal tar. This research was conducted in several steps, impregnating Co from Co(NO32.6H2O and Mo from (NH46Mo7O24.4H2O into Zeolite Y in liquid media, drying at 100 °C for 24 hours, and calcination at 550 °C for 3 hours. Coal tar was then reacted with hydrogen gas (as a reactant, and Co-Mo/Zeolite Y (as a catalyst was conducted at 350 °C. Characteristic analysis showed that Co and Mo had impregnated into the Y zeolite, as well as it made no change of catalyst’s structure and increased the total acidity. The higher of impregnation temperature was increased the catalyst crystallinity, total acidity, and yield of gasoline. The longer impregnation time was reduced crystallinity value, but total acidity and yield were increased. GC analysis showed that products included into the gasoline product (C8, C9, and C10. Copyright © 2017 BCREC Group. All rights reserved Received: 13rd November 2016; Revised: 12nd February 2017; Accepted: 16th February 2017 How to Cite: Anggoro, D.D., Buchori, L., Silaen, G.C., Utami, R.N. (2017. Preparation, Characterization, and Activation of Co-Mo/Y Zeolite Catalyst for Coal Tar Conversion to Liquid Fuel. Bulletin of Chemical Reaction Engineering & Catalysis, 12 (2: 219-226 (doi:10.9767/bcrec.12.2.768.219-226 Permalink/DOI: http://dx.doi.org/10.9767/bcrec.12.2.768.219-226

Pan Am tar sand bid revealed

Energy Technology Data Exchange (ETDEWEB)

Gray, E

1968-12-16

Muskeg Oil Co., wholly-owned subsidiary of Pan American Canada Oil Co. Ltd., hopes to expand its proposed initial 8,000 bpd in situ Athabasca tar sand production scheme to an ultimate rate of 60,000 bpd. The Muskeg recovery process involves an in situ combustion technique developed by Pan American and applied successfully in experimental work in the Athabasca area. The underground burning process develops heat in the formation, reduces crude bitumen viscosity, and displaces the bitumen to the producing wells. Core analyses have been used to determine bitumen in place, wherever possible. Values for uncored wells were based on logs, through development of an empirical relationship between formation resistivity measured by focused logging devices and bitumen content determined by core analysis. The proposed recovery process is a 10-acre well spacing with 9-spot configuration. The McMurray Formation will be fractured hydraulically and preheated by a combustion process. The bitumen will be recovered by a combustion displacement process utilizing air and water.

You're standing on it! Coal-tar-based pavement sealcoat and environmental and human health

Science.gov (United States)

Mahler, Barbara J.; Van Metre, Peter C.

2013-01-01

Coal-tar-based sealcoat—a product marketed to protect and beautify asphalt pavement—is a potent source of polycyclic aromatic hydrocarbons (PAHs) to air, soils, streams and lakes, and homes. Does its use present a risk to human health?

Do increases in cigarette prices lead to increases in sales of cigarettes with high tar and nicotine yields?

Science.gov (United States)

Farrelly, Matthew C; Loomis, Brett R; Mann, Nathan H

2007-10-01

We used scanner data on cigarette prices and sales collected from supermarkets across the United States from 1994 to 2004 to test the hypothesis that cigarette prices are positively correlated with sales of cigarettes with higher tar and nicotine content. During this period the average inflation-adjusted price for menthol cigarettes increased 55.8%. Price elasticities from multivariate regression models suggest that this price increase led to an increase of 1.73% in sales-weighted average tar yields and a 1.28% increase in sales-weighted average nicotine yields for menthol cigarettes. The 50.5% price increase of nonmenthol varieties over the same period yielded an estimated increase of 1% in tar per cigarette but no statistically significant increase in nicotine yields. An ordered probit model of the impact of cigarette prices on cigarette strength (ultra-light, light, full flavor, unfiltered) offers an explanation: As cigarette prices increase, the probability that stronger cigarette types will be sold increases. This effect is larger for menthol than for nonmenthol cigarettes. Our results are consistent with earlier population-based cross-sectional and longitudinal studies showing that higher cigarette prices and taxes are associated with increasing consumption of higher-yield cigarettes by smokers.

Identifying the source of tar balls deposited along the beaches of Goa in 2013 and comparing with historical data collected along the West Coast of India.

Science.gov (United States)

Suneel, V; Vethamony, P; Naik, B G; Krishna, M S; Jadhav, Lakshmikant

2015-09-15

Deposition of oil residues, also known as tar balls, is a seasonal phenomenon, and it occurs only in the southwest monsoon season along the west coast of India. This has become a serious environmental issue, as Goa is a global tourist destination. The present work aims at identifying the source oil of the tar balls that consistently depositing along the Goa coast using multi-marker fingerprint technique. In this context, the tar ball samples collected in May 2013 from 9 beaches of Goa coast and crude oils from different oil fields and grounded ship were subject to multi-marker analyses such as n-alkanes, pentacyclic terpanes, regular steranes, compound specific isotope analysis (CSIA) and principle component analysis (PCA). The n-alkane weathering index shows that samples have been weathered to various degrees, and the status of weathering is moderate. Since the international tanker route passes closer to the west coast of India (WCI), it is generally presumed that tanker wash is the source of the tar balls. We found that 2010/2011 tar balls are as tanker wash, but the present study demonstrates that the Bombay High (BH) oil fields can also contribute to oil contamination (tar balls) along ≈ 650 km stretch of the WCI, running from Gujarat in the north to Goa in the south. The simulated trajectories show that all the particles released in April traveled in the southeast direction, and by May, they reached the Goa coast with the influence of circulation of Indian monsoon system. Copyright © 2015 Elsevier B.V. All rights reserved.

Thermodynamic studies of a series of homologous HIV-1 TAR RNA ligands reveal that loose binders are stronger Tat competitors than tight ones.

Science.gov (United States)

Pascale, Lise; Azoulay, Stéphane; Di Giorgio, Audrey; Zenacker, Laura; Gaysinski, Marc; Clayette, Pascal; Patino, Nadia

2013-06-01

RNA is a major drug target, but the design of small molecules that modulate RNA function remains a great challenge. In this context, a series of structurally homologous 'polyamide amino acids' (PAA) was studied as HIV-1 trans-activating response (TAR) RNA ligands. An extensive thermodynamic study revealed the occurence of an enthalpy-entropy compensation phenomenon resulting in very close TAR affinities for all PAA. However, their binding modes and their ability to compete with the Tat fragment strongly differ according to their structure. Surprisingly, PAA that form loose complexes with TAR were shown to be stronger Tat competitors than those forming tight ones, and thermal denaturation studies demonstrated that loose complexes are more stable than tight ones. This could be correlated to the fact that loose and tight ligands induce distinct RNA conformational changes as revealed by circular dichroism experiments, although nuclear magnetic resonance (NMR) experiments showed that the TAR binding site is the same in all cases. Finally, some loose PAA also display promising inhibitory activities on HIV-infected cells. Altogether, these results lead to a better understanding of RNA interaction modes that could be very useful for devising new ligands of relevant RNA targets.

Composition and Dissolution of a Migratory, Weathered Coal Tar Creosote DNAPL

Directory of Open Access Journals (Sweden)

Kerstin E. Scherr

2016-09-01

Full Text Available Opaque, viscous tars derived from the carbonization of fossile carbon feedstocks, such coal tars and creosote, are long-term sources of groundwater contamination, predominantly with poly- and heterocyclic aromatic hydrocarbons (PAH. The dissolution, ageing and migratory behavior of dense, non aqueous phase liquid (DNAPL coal tar blobs and pools forming at the aquitard is not sufficiently understood to estimate the risk and adequately design groundwater treatment measures at a contaminated site. In this study, we investigate the composition and dissolution of a migrated, aged creosote DNAPL and corresponding experimental and groundwater profiles using comprehensive two-dimensional gas chromatography (GCxGC-MS. GC-FID unresolved compounds were attributed to methylated homocyclic species using GCxGC-MS in the Methylanthracene weight range. Equilibrium concentrations were estimated using Raoult’s law, assuming non-ideal behavior. Low molecular weight compounds were found to be prevalent even after decades of weathering, with Naphthalene (8% by mass representing the most abundant identified compound, contrary to the expected preferential depletion of hydrophilic compounds. Morevoer, dimethylnaphthalenes were relatively more abundant in the aqueous boundary layer than in the DNAPL. DNAPL migration over 400m with the groundwater flow effected lower viscosity and specific gravity of the migrated phase body in a superposition of weathering, transport and aquifer chromatography effects. Based on a decomposition of analysed and estimated constituents using the group contribution approach, reference DNAPL values for activity coefficients γi were used to model aqueous solubilities for selected compounds. Anthracene was close to its theoretical precipitation limit in the bulk DNAPL. While laboratory and modelled DNAPL dissolution behavior agree well, field data imply the presence of specific interfacial in situ processes significantly impacting dissolution

Thermal springs of Wyoming

Energy Technology Data Exchange (ETDEWEB)

Breckenridge, R.M.; Hinckley, B.S.

1978-01-01

This bulletin attempts, first, to provide a comprehensive inventory of the thermal springs of Wyoming; second, to explore the geologic and hydrologic factors producing these springs; and, third, to analyze the springs collectively as an indicator of the geothermal resources of the state. A general discussion of the state's geology and the mechanisms of thermal spring production, along with a brief comparison of Wyoming's springs with worldwide thermal features are included. A discussion of geothermal energy resources, a guide for visitors, and an analysis of the flora of Wyoming's springs follow the spring inventory. The listing and analysis of Wyoming's thermal springs are arranged alphabetically by county. Tabulated data are given on elevation, ownership, access, water temperature, and flow rate. Each spring system is described and its history, general characteristics and uses, geology, hydrology, and chemistry are discussed. (MHR)

Spring 5 & reactive streams

CERN Multimedia

CERN. Geneva; Clozel, Brian

2017-01-01

Spring is a framework widely used by the world-wide Java community, and it is also extensively used at CERN. The accelerator control system is constituted of 10 million lines of Java code, spread across more than 1000 projects (jars) developed by 160 software engineers. Around half of this (all server-side Java code) is based on the Spring framework. Warning: the speakers will assume that people attending the seminar are familiar with Java and Spring’s basic concepts. Spring 5.0 and Spring Boot 2.0 updates (45 min) This talk will cover the big ticket items in the 5.0 release of Spring (including Kotlin support, @Nullable and JDK9) and provide an update on Spring Boot 2.0, which is scheduled for the end of the year. Reactive Spring (1h) Spring Framework 5.0 has been released - and it now supports reactive applications in the Spring ecosystem. During this presentation, we'll talk about the reactive foundations of Spring Framework with the Reactor project and the reactive streams specification. We'll al...

Strontium isotopic composition of hot spring and mineral spring waters, Japan

International Nuclear Information System (INIS)

Notsu, Kenji; Wakita, Hiroshi; Nakamura, Yuji

1991-01-01

In Japan, hot springs and mineral springs are distributed in Quaternary and Neogene volcanic regions as well as in granitic, sedimentary and metamorphic regions lacking in recent volcanic activity. The 87 Sr/ 86 Sr ratio was determined in hot spring and mineral spring waters obtained from 47 sites. The ratios of waters from Quaternary and Neogene volcanic regions were in the range 0.703-0.708, which is lower than that from granitic, sedimentary and metamorphic regions (0.706-0.712). The geographical distribution of the ratios coincides with the bedrock geology, and particularly the ratios of the waters in Quaternary volcanic regions correlate with those of surrounding volcanic rocks. These features suggest that subsurface materials control the 87 Sr/ 86 Sr ratios of soluble components in the hot spring and mineral spring waters. (author)

AmTAR2: Functional characterization of a honeybee tyramine receptor stimulating adenylyl cyclase activity.

Science.gov (United States)

Reim, Tina; Balfanz, Sabine; Baumann, Arnd; Blenau, Wolfgang; Thamm, Markus; Scheiner, Ricarda

2017-01-01

The biogenic monoamines norepinephrine and epinephrine regulate important physiological functions in vertebrates. Insects such as honeybees do not synthesize these neuroactive substances. Instead, they employ octopamine and tyramine for comparable physiological functions. These biogenic amines activate specific guanine nucleotide-binding (G) protein-coupled receptors (GPCRs). Based on pharmacological data obtained on heterologously expressed receptors, α- and β-adrenergic-like octopamine receptors are better activated by octopamine than by tyramine. Conversely, GPCRs forming the type 1 tyramine receptor clade (synonymous to octopamine/tyramine receptors) are better activated by tyramine than by octopamine. More recently, receptors were characterized which are almost exclusively activated by tyramine, thus forming an independent type 2 tyramine receptor clade. Functionally, type 1 tyramine receptors inhibit adenylyl cyclase activity, leading to a decrease in intracellular cAMP concentration ([cAMP] i ). Type 2 tyramine receptors can mediate Ca 2+ signals or both Ca 2+ signals and effects on [cAMP] i . We here provide evidence that the honeybee tyramine receptor 2 (AmTAR2), when heterologously expressed in flpTM cells, exclusively causes an increase in [cAMP] i . The receptor displays a pronounced preference for tyramine over octopamine. Its activity can be blocked by a series of established antagonists, of which mianserin and yohimbine are most efficient. The functional characterization of two tyramine receptors from the honeybee, AmTAR1 (previously named AmTYR1) and AmTAR2, which respond to tyramine by changing cAMP levels in opposite direction, is an important step towards understanding the actions of tyramine in honeybee behavior and physiology, particularly in comparison to the effects of octopamine. Copyright © 2016 Elsevier Ltd. All rights reserved.

A natural tracer investigation of the hydrological regime of Spring Creek Springs, the largest submarine spring system in Florida

Science.gov (United States)

Dimova, Natasha T.; Burnett, William C.; Speer, Kevin

2011-04-01

This work presents results from a nearly two-year monitoring of the hydrologic dynamics of the largest submarine spring system in Florida, Spring Creek Springs. During the summer of 2007 this spring system was observed to have significantly reduced flow due to persistent drought conditions. Our examination of the springs revealed that the salinity of the springs' waters had increased significantly, from 4 in 2004 to 33 in July 2007 with anomalous high radon ( 222Rn, t1/2=3.8 days) in surface water concentrations indicating substantial saltwater intrusion into the local aquifer. During our investigation from August 2007 to May 2009 we deployed on an almost monthly basis a continuous radon-in-water measurement system and monitored the salinity fluctuations in the discharge area. To evaluate the springs' freshwater flux we developed three different models: two of them are based on water velocity measurements and either salinity or 222Rn in the associated surface waters as groundwater tracers. The third approach used only salinity changes within the spring area. The three models showed good agreement and the results confirmed that the hydrologic regime of the system is strongly correlated to local precipitation and water table fluctuations with higher discharges after major rain events and very low, even reverse flow during prolong droughts. High flow spring conditions were observed twice during our study, in the early spring and mid-late summer of 2008. However the freshwater spring flux during our observation period never reached that reported from a 1970s value of 4.9×10 6 m 3/day. The maximum spring flow was estimated at about 3.0×10 6 m 3/day after heavy precipitation in February-March 2008. As a result of this storm (total of 173 mm) the salinity in the spring area dropped from about 27 to 2 in only two days. The radon-in-water concentrations dramatically increased in parallel, from about 330 Bq/m 3 to about 6600 Bq/m 3. Such a rapid response suggests a direct

General toxic effects of shale tars on the human body

Energy Technology Data Exchange (ETDEWEB)

Kahn, H; Sillam, A

1972-01-01

Of 115 workers in close contact with oil shale tars, 80 percent complained of headache, fatigue, and stomach aches. Vegetative dystonia, asthenovegetative, or asthenic syndromes were diagnosed in 32 percent of the cases. An excessive excretion of free phenols was found in the urine of 13 percent of the patients and an excess of sulfates and coproporphyrin in 27 and 29 percent, respectively. The statistical analysis of clinical data indicates a relation to biochemical changes. The immunological reactivity studies showed that in 60 percent of the cases the immunological resistance decreased markedly.

Whole-stream metabolism of a perennial spring-fed aufeis field in Alaska, with coincident surface and subsurface flow

Science.gov (United States)

Hendrickson, P. J.; Gooseff, M. N.; Huryn, A. D.

2017-12-01

Aufeis (icings or naleds) are seasonal arctic and sub-arctic features that accumulate through repeated overflow and freeze events of river or spring discharge. Aufeis fields, defined as the substrate on which aufeis form and the overlaying ice, have been studied to mitigate impacts on engineering structures; however, ecological characteristics and functions of aufeis fields are poorly understood. The perennial springs that supply warm water to aufeis fields create unique fluvial habitats, and are thought to act as winter and summer oases for biota. To investigate ecosystem function, we measured whole-stream metabolism at the Kuparuk River Aufeis (North Slope, AK), a large ( 5 km2) field composed of cobble substrate and predominately subsurface flow dynamics. The single-station open channel diel oxygen method was utilized at several dissolved oxygen (DO) stations located within and downstream of the aufeis field. DO loggers were installed in August 2016, and data downloaded summer 2017. Daily ecosystem respiration (ER), gross primary production (GPP) and reaeration rates were modeled using BASE, a package freely available in the open-source software R. Preliminary results support net heterotrophy during a two-week period of DO measurements in the fall season when minimum ice extent is observed. GPP, ER, and net metabolism are greater at the upstream reach near the spring source (P/R = 0.53), and decrease as flow moves downstream. As flow exits the aufeis field, surface and subsurface flow are incorporated into the metabolism model, and indicate the stream system becomes dependent on autochthonous production (P/R = 0.91). Current work is directed towards spring and summer discharge and metabolic parameter estimation, which is associated with maximum ice extent and rapid melting of the aufeis feature.

The effects of higher cigarette prices on tar and nicotine consumption in a cohort of adult smokers.

Science.gov (United States)

Farrelly, M C; Nimsch, C T; Hyland, A; Cummings, M

2004-01-01

The objective of this paper is to estimate the demand for tar and nicotine in cigarettes as a function of cigarette prices in a cohort of cigarette 11,966 smokers followed for 5 years. Data for the analysis come from a longitudinal telephone survey of 11,966 smokers who were interviewed in 1988 and 1993 as part of the Community Intervention Trial for Smoking Cessation (COMMIT). Separate models are estimated for three age groups to account for differences in levels of addiction and brand loyalty across age. We found that smokers respond to higher cigarette prices by reducing the number of cigarettes smoked per day but also by switching to cigarettes that are higher in tar and nicotine per cigarette. Copyright 2003 John Wiley & Sons, Ltd.

Instant Spring Tool Suite

CERN Document Server

Chiang, Geoff

2013-01-01

Filled with practical, step-by-step instructions and clear explanations for the most important and useful tasks. A tutorial guide that walks you through how to use the features of Spring Tool Suite using well defined sections for the different parts of Spring.Instant Spring Tool Suite is for novice to intermediate Java developers looking to get a head-start in enterprise application development using Spring Tool Suite and the Spring framework. If you are looking for a guide for effective application development using Spring Tool Suite, then this book is for you.

Protection Performance Simulation of Coal Tar-Coated Pipes Buried in a Domestic Nuclear Power Plant Using Cathodic Protection and FEM Method

Energy Technology Data Exchange (ETDEWEB)

Chang, H. Y.; Lim, B. T.; Kim, K. S.; Kim, J. W.; Park, H. B. [KEPCO Engineering and Construction Company, Gimcheon (Korea, Republic of); Kim, Y. S.; Kim, K. T. [Andong National University, Andong (Korea, Republic of)

2017-06-15

Coal tar-coated pipes buried in a domestic nuclear power plant have operated under the cathodic protection. This work conducted the simulation of the coating performance of these pipes using a FEM method. The pipes, being ductile cast iron have been suffered under considerably high cathodic protection condition beyond the appropriate condition. However, cathodic potential measured at the site revealed non-protected status. Converting from 3D CAD data of the power plant to appropriate type for a FEM simulation was conducted and cathodic potential under the applied voltage and current was calculated using primary and secondary current distribution and physical conditions. FEM simulation for coal tar-coated pipe without defects revealed over-protection condition if the pipes were well-coated. However, the simulation for coal tar-coated pipes with many defects predict that the coated pipes may be severely degraded. Therefore, for high risk pipes, direct examination and repair or renewal of pipes are strongly recommended.

Corrosão de parafusos fixados à madeira tratada com soluções de creosoto vegetal Corrosion of screws fixed into wood treated with wood tar creosote solutions

Directory of Open Access Journals (Sweden)

Juarez Benigno Paes

2002-05-01

Full Text Available O objetivo desta pesquisa foi avaliar a corrosão de parafusos auto-rosqueáveis fixados à madeira tratada com soluções preservativas preparadas com creosoto vegetal, em condições de campo. Obteve-se o creosoto vegetal bruto por meio da destilação à temperatura de 110 - 255ºC do alcatrão vegetal. Uma fração dos destilados foi lavada com solução a 9% de bicarbonato de sódio, obtendo-se o creosoto vegetal purificado. Ambas as frações foram enriquecidas com 3% de naftenato de cobre; 3% de naftenato de zinco; 3% naftenato de cobalto; 2% de TBTO; 2% de tribromofenato de tubutil-estanho; 2% de pentaclorofenol; ou 0,4% de trióxido de arsênico. Foram preparadas 16 soluções, sendo 14 enriquecidas, além do creosoto vegetal bruto e do creosoto vegetal purificado. Estacas confeccionadas com madeira de alburno de Eucalyptus grandis foram tratadas pelo processo de célula- cheia (processo Bethell. Após o tratamento, parafusos auto-rosquéaveis de ferro zincado foram fixados às estacas. O ensaio foi instalado em três localidades da Zona da Mata de Minas Gerais (Viçosa, Ponte Nova e Leopoldina. A corrosividade das soluções de creosoto vegetal foi comparada à causada pelo creosoto mineral. As soluções preparadas com creosoto vegetal purificado foram menos corrosivas que suas similares preparadas com creosoto vegetal bruto, assemelhando-se ao creosoto mineral.The objective of this research was to evaluate the corrosion of screws fixed into wood treated with preservative solutions of wood tar creosote. The crude wood tar creosote was obtained through distillation of wood tar at 110 - 255ºC. A fraction of this product was washed with a solution of sodium bicarbonate at 9%, resulting in purified wood tar creosote. Both fractions were enriched with 3% of copper naphtenate, 3% of zinc naphtenate, 3% of cobalt naphtenate, 2% of TBTO, 2% of tributhyl-tin tribromophenate, 2% of pentachlorophenol, or with 0.4% of arsenic trioxide. A total

Radiation hardness of LuAG:Ce and LuAG:Pr scintillator crystals

CERN Document Server

Derdzyan, M V; Belsky, A; Dujardin, C; Lecoq, P; Lucchini, M; Ovanesyan, K L; Pauwels, K; Pedrini, C; Petrosyan, A G

2012-01-01

Single crystals of LuAG:Ce, LuAG:Pr and un-doped LuAG were grown by the vertical Bridgman method and studied for radiation hardness under gamma-rays with doses in the range 10-10(5) Gy (Co-60). A wide absorption band peaking at around 600 nm springs up in all three types of crystals after the irradiations. The second band peaking at around 375 nm appears in both LuAG:Pr and un-doped LuAG. Compositional variations have been done to reveal the spectral behavior of induced color centers in more detail and to understand their origin. Similarities in behavior of Yb2+ centers in as-grown garnets are found, indicating that radiation induced color centers can be associated with residual trace amounts of Yb present in the raw materials. Un-doped LuAG and LuAG:Ce demonstrate moderate radiation hardness (the induced absorption coefficients being equal to 0.05-0.08 cm(-1) for accumulated doses of 10(3)-10(4) Gy), while LuAG:Pr is less radiation hard. The ways to improve the radiation hardness are discussed.

Production of gas and volatile materials by distillation of tars, etc

Energy Technology Data Exchange (ETDEWEB)

Arson, M

1860-04-25

The principle of this production is in the treating of heavy oils with heat, their transformation occurring nearly completely by the action of this agent. The apparatus used consists of a retort of such a form that it has openings at the two ends immediately opposed to each other. One serves to introduce the oil and the other to remove the tar and gas produced. At the exit of the apparatus the gas passes into coolers like those used for coal gas.

Pro Spring Integration

CERN Document Server

Lui, M; Chan, Andy; Long, Josh

2011-01-01

Pro Spring Integration is an authoritative book from the experts that guides you through the vast world of enterprise application integration (EAI) and application of the Spring Integration framework towards solving integration problems. The book is:. * An introduction to the concepts of enterprise application integration * A reference on building event-driven applications using Spring Integration * A guide to solving common integration problems using Spring Integration What makes this book unique is its coverage of contemporary technologies and real-world information, with a focus on common p

Synthesis Of 2- (1- Naphthyl) Ethanoic Acid ( Plant Growth Regulator ) From Coal Tar And Its Application

International Nuclear Information System (INIS)

Khin Mooh Theint; Tin Myint Htwe

2011-12-01

Plant growth regulators, which are commonly called as plant hormones, naturally produced non-nutrient chemical compounds involved in growth and development. Among the various kinds of plant growth regulators, 2- (1- Naphthyl ) ethanoic acid especially encourages the root development of the plant. In this work, NAA was successfuly synthesized from naphthalene which was extracted from coal tar. The purity of naphthalene, -Chloromethyl naphthalene, -Naphthyl acetonitrile, - Naphthyl acetic acid or 2 - ( 1-Naphthyl ) ethanoic acid were also confirmed by Thin Layer Chromatography, and by spectroscopy methods. The yield percent of NAA based on naphthalene was found to be 2.1%. The yield percent of naphthaleneFrom coal tar is found to be 4.09%. The effect of NAA on root development was also studied in different concentrations of soy bean (Glycine max)and cow pea (Vigna catjang walp).

Smokers' sensory beliefs mediate the relation between smoking a light/low tar cigarette and perceptions of harm.

Science.gov (United States)

Elton-Marshall, Tara; Fong, Geoffrey T; Yong, Hua-Hie; Borland, Ron; Xu, Steve Shaowei; Quah, Anne C K; Feng, Guoze; Jiang, Yuan

2015-11-01

The sensory belief that 'light/low tar' cigarettes are smoother can also influence the belief that 'light/low tar' cigarettes are less harmful. However, the 'light' concept is one of several factors influencing beliefs. No studies have examined the impact of the sensory belief about one's own brand of cigarettes on perceptions of harm. The current study examines whether a smoker's sensory belief that their brand is smoother is associated with the belief that their brand is less harmful and whether sensory beliefs mediate the relation between smoking a 'light/low tar' cigarette and relative perceptions of harm among smokers in China. Data are from 5209 smokers who were recruited using a stratified multistage sampling design and participated in Wave 3 of the International Tobacco Control (ITC) China Survey, a face-to-face survey of adult smokers and non-smokers in seven cities. Smokers who agreed that their brand of cigarettes was smoother were significantly more likely to say that their brand of cigarettes was less harmful (pmarketing can have in capitalising on the smoker's natural associations between smoother sensations and lowered perceptions of harm. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Inhibition of both HIV-1 reverse transcription and gene expression by a cyclic peptide that binds the Tat-transactivating response element (TAR RNA.

Directory of Open Access Journals (Sweden)

Matthew S Lalonde

2011-05-01

Full Text Available The RNA response element TAR plays a critical role in HIV replication by providing a binding site for the recruitment of the viral transactivator protein Tat. Using a structure-guided approach, we have developed a series of conformationally-constrained cyclic peptides that act as structural mimics of the Tat RNA binding region and block Tat-TAR interactions at nanomolar concentrations in vitro. Here we show that these compounds block Tat-dependent transcription in cell-free systems and in cell-based reporter assays. The compounds are also cell permeable, have low toxicity, and inhibit replication of diverse HIV-1 strains, including both CXCR4-tropic and CCR5-tropic primary HIV-1 isolates of the divergent subtypes A, B, C, D and CRF01_AE. In human peripheral blood mononuclear cells, the cyclic peptidomimetic L50 exhibited an IC(50 ∼250 nM. Surprisingly, inhibition of LTR-driven HIV-1 transcription could not account for the full antiviral activity. Timed drug-addition experiments revealed that L-50 has a bi-phasic inhibition curve with the first phase occurring after HIV-1 entry into the host cell and during the initiation of HIV-1 reverse transcription. The second phase coincides with inhibition of HIV-1 transcription. Reconstituted reverse transcription assays confirm that HIV-1 (- strand strong stop DNA synthesis is blocked by L50-TAR RNA interactions in-vitro. These findings are consistent with genetic evidence that TAR plays critical roles both during reverse transcription and during HIV gene expression. Our results suggest that antiviral drugs targeting TAR RNA might be highly effective due to a dual inhibitory mechanism.

The pentane- and toluene-soluble fractions of a petroleum residue and three coal tars by size exclusion chromatography and UV-fluorescence spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Karaca, F.; Millan-Agorio, M.; Morgan, T.J.; Bull, I.D.; Herod, A.A.; Kandiyoti, R. [University of London Imperial College Science Technology & Medicine, London (United Kingdom). Dept. of Chemical Engineering

2008-01-15

A petroleum atmospheric pressure distillate residue and three tars derived from different coals using different severities of thermal treatment were separated into seven fractions using column chromatography on silica and sequential elution by the solvent sequence pentane, toluene, acetonitrile, pyridine, 1-methyl-2-pyrrolidinone (NMP) and water. The fractions from the four extractions have been compared using size exclusion chromatography (SEC) in NMP as eluent and by synchronous ultra-violet-fluorescence (UV-F). This paper concerns the pentane and toluene soluble fractions only since these are the least polar fractions. By SEC, the size of the aromatic molecules increased from the first pentane soluble fractions to the toluene-soluble fractions, with the petroleum residue fractions of larger size than the equivalent fractions from coal liquids. The three coal tars showed significant differences, indicating that temperature of pyrolysis had a significant effect on the molecular size. Synchronous UV-F spectra of the four sets of fractions, in solution in NMP, again showed significant differences between the petroleum residue and the coal tars, as well as amongst the three coal tars. In general, the petroleum residue fractions contained smaller aromatic clusters than the coal liquid fractions. These low-polarity fractions contained material excluded from the column porosity in SEC that was unlikely to consist of aggregates of polar molecules.

Economic and environmental effects of the FQD on crude oil production from tar sands

Energy Technology Data Exchange (ETDEWEB)

Kampman, B.; De Buck, A.; Afman, M. [CE Delft, Delft (Netherlands); Van den Berg, J.; Otten, G.J. [Carbon Matters, Den Haag (Netherlands)

2013-05-15

The production of unconventional crudes in Canada and Venezuela and exports of these crudes to the EU are investigated. In addition the potential economic and environmental impact of the proposed EU FQD measures (Fuel Quality Directive) on the production of crudes from tar sands and on new tar sand exploration projects are examined. CE Delft has analysed the impact by using a dedicated cost model. For existing projects, the model determines the effect on the basis of marginal production costs. For planned projects the model used the net present value (NPV) of proposed investments. The impacts were determined for a range of crude oil prices and FQD price effects. Combined, for existing and new projects together, the maximum effect would be at a price level at 60 USD/bbl, with savings of up to 19 Mt CO2/y at an FQD price differential of 3 euro/bbl. This overall effect would be substantial and come on top of the total emission reduction effect of the FQD of 60 Mt CO2/y, which will be achieved mostly by the blending of low-carbon fuels and reduced flaring and venting. As part of the reduction of transport greenhouse gas (GHG) emissions, the revised FQD obliges fuel suppliers to reduce these emissions by 6% by 2020 on a well-to-wheel basis. The EU is currently developing a methodology to differentiate fossil fuels on the basis of feedstock and GHG emissions. In the proposal, diesel produced from tar sands, has been given a default emission value of 108.5 gCO2 eq/MJ, while diesel from conventional crude was set at 89.1 gCO2 eq/MJ. The Commission's proposal is currently undergoing an impact assessment and is expected to be resubmitted to the Council later this year (2013)

Investigating Efficient Tar Management from Biomass and Waste to Energy Gasification Processes

Science.gov (United States)

2015-04-01

internal combustion engine (ICE) can mean spark ignition or diesel ( compression ignition ). It is likely that the light tars could be made to burn in...filled with methyl chloroform to allow rapid acquisition and analysis via an auto handler on the gas chromatography machine. An additional test...flare and venturi are lost. If the venturi were lost air can draw back into the process pipe creating an air fuel mixture that may ignite . PLASMA

Tar sand extraction by steam stimulation and steam drive: measurement of physical properties

Energy Technology Data Exchange (ETDEWEB)

Linberg, W.R.

1980-09-10

The measurement of the following thermophysical properties of Utah tar sands is in progress: thermal conductivity, specific heat relative permeability, and viscosity (of the recovered bitumen). During the report period (October 1, 1978 to November 1, 1979), experimental procedures have been developed and a basic data set has been measured. Additionally, standard core analysis has been performed for four drill sites in the Asphalt Ridge, Utah area.

Plasma Gasification of Wood and Production of Gas with Low Content of Tar

Czech Academy of Sciences Publication Activity Database

Hlína, Michal; Hrabovský, Milan; Kopecký, Vladimír; Konrád, Miloš; Kavka, Tetyana; Skoblja, S.

2006-01-01

Roč. 56, suppl. B (2006), s. 1179-1184 ISSN 0011-4626. [Symposium on Plasma Physics and Technology/22nd./. Praha, 26.6.2006-29.6.2006] R&D Projects: GA ČR GA202/05/0669 Institutional research plan: CEZ:AV0Z20430508 Keywords : tar * plasma * biomass gasification Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 0.568, year: 2006

PFB air gasification of biomass. Investigation of product formation and problematic issues related to ammonia, tar and alkali

Energy Technology Data Exchange (ETDEWEB)

Padban, Nader

2000-09-01

Fluidised bed thermal gasification of biomass is an effective route that results in 100 % conversion of the fuel. In contrast to chemical, enzymatic or anaerobic methods of biomass treatment, the thermal conversion leaves no contaminated residue after the process. The product gas evolved within thermal conversion can be used in several applications such as: fuel for gas turbines, combustion engines and fuel cells, and raw material for production of chemicals and synthetic liquid fuels. This thesis treats a part of the experimental data from two different gasifiers: a 90 kW{sub th} pressurised fluidised bubbling bed gasifier at Lund University and a 18 MW{sub th} circulating fluidised bed gasifier integrated with gas turbine (IGCC) in Vaernamo. A series of parallel and consecutive chemical reactions is involved in thermal gasification, giving origin to formation of a variety of products. These products can be classified within three major groups: gases, tars and oils, and char. The proportion of these categories of species in the final product is a matter of the gasifier design and the process parameters. The thesis addresses the technical and theoretical aspects of the biomass thermochemical conversion and presents a new approach in describing the gasification reactions. There is an evidence of fuel effect on the characteristics of the final products: a mixture of plastic waste (polyethylene) and biomass results in higher concentration of linear hydrocarbons in the gas than gasification of pure biomass. Mixing the biomass with textile waste (containing aromatic structure) results in a high degree of formation of aromatic compounds and light tars. Three topic questions within biomass gasification, namely: tar, NO{sub x} and alkali are discussed in the thesis. The experimental results show that gasification at high ER or high temperature decreases the total amount of the tars and simultaneously reduces the contents of the oxygenated and alkyl-substituted poly

PrP Knockout Cells Expressing Transmembrane PrP Resist Prion Infection.

Science.gov (United States)

Marshall, Karen E; Hughson, Andrew; Vascellari, Sarah; Priola, Suzette A; Sakudo, Akikazu; Onodera, Takashi; Baron, Gerald S

2017-01-15

Glycosylphosphatidylinositol (GPI) anchoring of the prion protein (PrP C ) influences PrP C misfolding into the disease-associated isoform, PrP res , as well as prion propagation and infectivity. GPI proteins are found in cholesterol- and sphingolipid-rich membrane regions called rafts. Exchanging the GPI anchor for a nonraft transmembrane sequence redirects PrP C away from rafts. Previous studies showed that nonraft transmembrane PrP C variants resist conversion to PrP res when transfected into scrapie-infected N2a neuroblastoma cells, likely due to segregation of transmembrane PrP C and GPI-anchored PrP res in distinct membrane environments. Thus, it remained unclear whether transmembrane PrP C might convert to PrP res if seeded by an exogenous source of PrP res not associated with host cell rafts and without the potential influence of endogenous expression of GPI-anchored PrP C To further explore these questions, constructs containing either a C-terminal wild-type GPI anchor signal sequence or a nonraft transmembrane sequence containing a flexible linker were expressed in a cell line derived from PrP knockout hippocampal neurons, NpL2. NpL2 cells have physiological similarities to primary neurons, representing a novel and advantageous model for studying transmissible spongiform encephalopathy (TSE) infection. Cells were infected with inocula from multiple prion strains and in different biochemical states (i.e., membrane bound as in brain microsomes from wild-type mice or purified GPI-anchorless amyloid fibrils). Only GPI-anchored PrP C supported persistent PrP res propagation. Our data provide strong evidence that in cell culture GPI anchor-directed membrane association of PrP C is required for persistent PrP res propagation, implicating raft microdomains as a location for conversion. Mechanisms of prion propagation, and what makes them transmissible, are poorly understood. Glycosylphosphatidylinositol (GPI) membrane anchoring of the prion protein (PrP C

Concerted motions in HIV-1 TAR RNA may allow access to bound state conformations: RNA dynamics from NMR residual dipolar couplings.

Science.gov (United States)

Al-Hashimi, Hashim M; Gosser, Yuying; Gorin, Andrey; Hu, Weidong; Majumdar, Ananya; Patel, Dinshaw J

2002-01-11

Ground-state dynamics in RNA is a critical precursor for structural adaptation observed ubiquitously in protein-RNA recognition. A tertiary conformational analysis of the stem-loop structural element in the transactivation response element (TAR) from human immunodeficiency virus type 1 (HIV-I) RNA is presented using recently introduced NMR methods that rely on the measurement of residual dipolar couplings (RDC) in partially oriented systems. Order matrix analysis of RDC data provides evidence for inter-helical motions that are of amplitude 46(+/-4) degrees, of random directional character, and that are executed about an average conformation with an inter-helical angle between 44 degrees and 54 degrees. The generated ensemble of TAR conformations have different organizations of functional groups responsible for interaction with the trans-activator protein Tat, including conformations similar to the previously characterized bound-state conformation. These results demonstrate the utility of RDC-NMR for simultaneously characterizing RNA tertiary dynamics and average conformation, and indicate an avenue for TAR complex formation involving tertiary structure capture. Copyright 2001 Academic Press.

Preliminary evaluation of ground-water contamination by coal-tar derivatives, St. Louis Park area, Minnesota

Science.gov (United States)

Hult, Marc F.; Schoenberg, Michael E.

1984-01-01

Operation of a coal-tar distillation and wood-preserving plant from 1918 to 1972 in St. Louis Park, a suburb of Minneapolis, Minn., resulted in ground-water contamination. This preliminary evaluation presents an overview of the problem based on the results of the first year (1979) of an ongoing study.

Mercury content in Hot Springs

Energy Technology Data Exchange (ETDEWEB)

Nakagawa, R

1974-01-01

A method of determination of mercury in hot spring waters by flameless atomic absorption spectrophotometry is described. Further, the mercury content and the chemical behavior of the elementary mercury in hot springs are described. Sulfide and iodide ions interfered with the determination of mercury by the reduction-vapor phase technique. These interferences could, however, be minimized by the addition of potassium permanganate. Waters collected from 55 hot springs were found to contain up to 26.0 ppb mercury. High concentrations of mercury have been found in waters from Shimoburo Springs, Aomori (10.0 ppb), Osorezan Springs, Aomori (1.3 approximately 18.8 ppb), Gosyogake Springs, Akita (26.0 ppb), Manza Springs, Gunma (0.30 approximately 19.5 ppb) and Kusatu Springs, Gunma (1.70 approximately 4.50 ppb). These hot springs were acid waters containing a relatively high quantity of chloride or sulfate.

A Tat-grafted anti-nucleic acid antibody acquires nuclear-localization property and a preference for TAR RNA

International Nuclear Information System (INIS)

Jeong, Jong-Geun; Kim, Dong-Sik; Kim, Yong-Sung; Kwon, Myung-Hee

2011-01-01

Highlights: → We generate ' H3 Tat-3D8' by grafting Tat 48-60 peptide to VH CDR of 3D8 scFv antibody. → H3 Tat-3D8 antibody retains nucleic acid binding and hydrolyzing activities. → H3 Tat-3D8 acquires a preference for TAR RNA structure. → Properties of Tat 48-60 is transferred to an antibody via Tat-grafting into a CDR. -- Abstract: The 3D8 single chain variable fragment (3D8 scFv) is an anti-nucleic acid antibody that can hydrolyze nucleic acids and enter the cytosol of cells without reaching the nucleus. The Tat peptide, derived from the basic region of the HIV-1 Tat protein, translocates to cell nuclei and has TAR RNA binding activity. In this study, we generated a Tat-grafted antibody ( H3 Tat-3D8) by replacing complementarity-determining region 3 (CDR3) within the VH domain of the 3D8 scFv with a Tat 48-60 peptide (GRKKRRQRRRPPQ). H3 Tat-3D8 retained the DNA-binding and DNA-hydrolyzing activity of the scFv, and translocated to the nuclei of HeLa cells and preferentially recognized TAR RNA. Thus, the properties associated with the Tat peptide were transferred to the antibody via Tat-grafting without loss of the intrinsic DNA-binding and hydrolyzing activities of the 3D8 scFv antibody.

Functional analysis of a Wheat Homeodomain protein, TaR1, reveals that host chromatin remodelling influences the dynamics of the switch to necrotrophic growth in the phytopathogenic fungus Zymoseptoria tritici.

Science.gov (United States)

Lee, Jack; Orosa, Beatriz; Millyard, Linda; Edwards, Martin; Kanyuka, Kostya; Gatehouse, Angharad; Rudd, Jason; Hammond-Kosack, Kim; Pain, Naomi; Sadanandom, Ari

2015-04-01

A distinguishing feature of Septoria leaf blotch disease in wheat is the long symptomless growth of the fungus amongst host cells followed by a rapid transition to necrotrophic growth resulting in disease lesions. Global reprogramming of host transcription marks this switch to necrotrophic growth. However no information exists on the components that bring about host transcriptional reprogramming. Gene-silencing, confocal-imaging and protein-protein interaction assays where employed to identify a plant homeodomain (PHD) protein, TaR1 in wheat that plays a critical role during the transition from symptomless to necrotrophic growth of Septoria. TaR1-silenced wheat show earlier symptom development upon Septoria infection but reduced fungal sporulation indicating that TaR1 is key for prolonging the symptomless phase and facilitating Septoria asexual reproduction. TaR1 is localized to the nucleus and binds to wheat Histone 3. Trimethylation of Histone 3 at lysine 4 (H3K4) and lysine 36 (H3K36) are found on open chromatin with actively transcribed genes, whereas methylation of H3K27 and H3K9 are associated with repressed loci. TaR1 specifically recognizes dimethylated and trimethylated H3K4 peptides suggesting that it regulates transcriptional activation at open chromatin. We conclude that TaR1 is an important component for the pathogen life cycle in wheat that promotes successful colonization by Septoria. © 2015 The Authors. New Phytologist © 2015 New Phytologist Trust.

Groundwater monitoring strategies at the Weldon Spring site, Weldon Spring, Missouri

International Nuclear Information System (INIS)

Meyer, K.A. Jr.

1988-01-01

This paper presents groundwater monitoring strategies at the Weldon Spring Site in east-central Missouri. The Weldon Spring Site is former ordnance works and uranium processing facility. In 1987, elevated levels of inorganic anions and nitroaromatics were detected in groundwater beneath the site. Studies are currently underway to characterize the hydrogeologic regime and to define groundwater contamination. The complex hydrogeology at the Weldon Spring Site requires innovative monitoring strategies. Combinations of fracture and conduit flow exist in the limestone bedrock. Perched zones are also present near surface impoundments. Losing streams and springs surround the site. Confronting this complex combination of hydrogeologic conditions is especially challenging

Visit to valuable water springs. 22. ; Kanazawa spring and springs at the mountain flank of Iwate volcano. Meisui wo tazunete. 22. ; Kanazawa shimizu to Iwate sanroku yusuigun

Energy Technology Data Exchange (ETDEWEB)

Itadera, K. (Kanagawa Hot Springs Research Institute, Kanagawa (Japan)); Shimano, Y. (Utsunomiya Bunsei Junior College, Tochigi (Japan))

1993-06-30

This paper describes the following matters on the springs at the mountain flank of Iwate volcano in Iwate Prefecture, with the Kanazawa spring as the main subject: The new and old Iwate volcanos have rock-bed flow deposits which resulted from mountain disintegration, distributed over their south, east and north flanks, and most of the spring water wells up in these areas; the south, east and north flanks have about 80 springs, about 30 springs, and about 10 springs, respectively; the number of springs and the water well-up scale show a trend of inverse proportion; the Kanazawa spring is a generic name of the several springs located on the north flank in the Kanazawa area; its main spring forms a spring pond with an area of about 100 m[sup 2] with a spring water temperature of about 11.5[degree]C, electric conductivity of 200 [mu] S/cm or higher, and a flow-out rate of 500 l/s or more; the Kanazawa spring is characterized by having as large total dissolved component amount as 170 mg/l or more and abundant amount of SO4[sup 2-] and Cl[sup -]; and the spring presents properties different from those in other springs. 10 refs., 5 figs., 1 tab.

Cashing in on Tar Sands. RBS, UK banks and Canada's 'blood oil'

Energy Technology Data Exchange (ETDEWEB)

Evans, M.; Howarth, C.; Kellay, A.; Laboucan, B.J.; Mercredi, M.; Minio-Paluelo, M.; Schling, H.; Smith, K.; Thomas-Muller, C.; Wood, A.

2010-03-15

Tar sands extraction in Canada is devastating Indigenous communities, wildlife and vast areas of boreal forests, as well as being many times more carbon-intensive to produce than 'conventional' oil. The higher oil prices in recent years have meant that it's become a more attractive prospect for oil companies to expand their operations in the costly process of obtaining and processing the thick bitumen into a usable form. It's estimated that the industry is looking for a capital investment of 120-220 billion USD over the next 20 years to build the new pipelines, mines, refineries and upgraders that are necessary to sustain the boom. This report looks at the role that UK banks are playing in providing the necessary capital, and how RBS (Royal Bank of Scotland), which is 84% owned by the UK public, has been the bank the most heavily involved in underwriting loans to companies engaging in tar sands extraction.

Spring integration essentials

CERN Document Server

Pandey, Chandan

2015-01-01

This book is intended for developers who are either already involved with enterprise integration or planning to venture into the domain. Basic knowledge of Java and Spring is expected. For newer users, this book can be used to understand an integration scenario, what the challenges are, and how Spring Integration can be used to solve it. Prior experience of Spring Integration is not expected as this book will walk you through all the code examples.

Getting started with Spring Framework a hands-on guide to begin developing applications using Spring Framework

CERN Document Server

Sharma, J

2016-01-01

Getting started with Spring Framework is a hands-on guide to begin developing applications using Spring Framework. The examples (consisting of 74 sample projects) that accompany this book are based on Spring 4.3 and Java 8. You can download the examples described in this book from the following GitHub project:github.com/getting-started-with-spring/3rdEdition This book is meant for Java developers with little or no knowledge of Spring Framework. Getting started with Spring Framework, Third Edition has been updated to reflect changes in Spring 4.3 and also includes new chapters on Java-based configuration and Spring Data (covers Spring Data JPA and Spring Data MongoDB projects). The existing chapters have been revised to include information on Java-based configuration. The book also includes some new information on bean definition profiles, importing application context XML files, lazy autowiring, creating custom qualifier annotations, JSR 349 annotations, spring-messaging module, Java 8's Optional type, and s...

Occurrence and variability of mining-related lead and zinc in the Spring River flood plain and tributary flood plains, Cherokee County, Kansas, 2009--11

Science.gov (United States)

Juracek, Kyle E.

2013-01-01

, Cow Creek, and Shawnee Creek—generally had flood-plain lead and zinc concentrations (surficial soil, 6- and 12-inch depth) that were substantially less than the general PECs. Tributaries with extensive lead- and zinc-mined areas in the basin—Shoal Creek, Short Creek, Spring Branch, Tar Creek, Turkey Creek, and Willow Creek—had flood-plain lead concentrations (surficial soil, 6- and 12-inch depth) that frequently or typically exceeded the general and TSMD-specific PECs. Likewise, the tributaries with extensive lead- and zinc-mined areas in the basin had flood-plain zinc concentrations (surficial soil, 6- and 12-inch depth) that frequently or typically exceeded the general PEC. With the exception of Shoal and Willow Creeks, zinc concentrations typically exceeded the TSMD-specific PEC. The largest flood-plain lead and zinc concentrations (surficial soil, 6- and 12-inch depth) were measured for Short and Tar Creeks. Lead and zinc concentrations in the surficial-soil samples collected from the tributary flood plains varied longitudinally in relation to sources of mining-contaminated sediment in the basins. Lead and zinc concentrations also varied with distance from the channel; however, no consistent spatial trend was evident. For the surficial-soil samples collected from the Spring River flood plain and tributary flood plains, both the coarse (larger than 63 micrometers) and fine particles (less than 63 micrometers) contained substantial lead and zinc concentrations.

On PR group classes and PR algebra membership

International Nuclear Information System (INIS)

Lebedenko, V.M.

1978-01-01

The necessary and sufficient conditions are found for the membership of Lee algebras to PR algebra class, to algebras with commutation relations of [Hsub(i), Hsub(j)]=rsub(ij)Hsub(i) (i< j) type. Due to this, a criterion is obtained for the membership of the Lee froups to PR group classes, connected and simply connected Lee groups, which Lee algebras are PR algebras

The source, discharge, and chemical characteristics of water from Agua Caliente Spring, Palm Springs, California

Science.gov (United States)

Contributors: Brandt, Justin; Catchings, Rufus D.; Christensen, Allen H.; Flint, Alan L.; Gandhok, Gini; Goldman, Mark R.; Halford, Keith J.; Langenheim, V.E.; Martin, Peter; Rymer, Michael J.; Schroeder, Roy A.; Smith, Gregory A.; Sneed, Michelle; Martin, Peter

2011-01-01

Agua Caliente Spring, in downtown Palm Springs, California, has been used for recreation and medicinal therapy for hundreds of years and currently (2008) is the source of hot water for the Spa Resort owned by the Agua Caliente Band of the Cahuilla Indians. The Agua Caliente Spring is located about 1,500 feet east of the eastern front of the San Jacinto Mountains on the southeast-sloping alluvial plain of the Coachella Valley. The objectives of this study were to (1) define the geologic structure associated with the Agua Caliente Spring; (2) define the source(s), and possibly the age(s), of water discharged by the spring; (3) ascertain the seasonal and longer-term variability of the natural discharge, water temperature, and chemical characteristics of the spring water; (4) evaluate whether water-level declines in the regional aquifer will influence the temperature of the spring discharge; and, (5) estimate the quantity of spring water that leaks out of the water-collector tank at the spring orifice.

Researching the technology of tar removal from coke-chemical plants’ wastewater by reagent flotation method

Directory of Open Access Journals (Sweden)

Anna V. Ivanchenko

2015-03-01

Full Text Available The study aims to identify process patterns of tars and oils removal from phenolic wastewater by reagent flotation with bringing those components’ content to acceptable concentrations. For the first time established is the effect of Al2(SO43, AlCl3, FeSO4, Fe2(SO43, Al2(OH5Cl and FeCl3 doses onto residual tar content in phenolic wastewater. Results obtained give the possibility to prevent air pollution resulting from the toxic substances emission at the wet quenching with water containing excessive oils and to increase the quality of wastewater biological treatment. It is shown experimentally that the most efficient are Fe2(SO43, FeCl3 and Al2(OH5Cl at optimum concentrations of 50, 30 and 30 mg/dm3 respectively. The Al2(OH5Cl can be recommended for implementation at industry on existing coking plants and municipal wastewater treatment plants to improve the environmental air and water resources condition in Ukraine.

Spring plant phenology and false springs in the conterminous US during the 21st century

Science.gov (United States)

Allstadt, Andrew J.; Vavrus, Stephen J.; Heglund, Patricia J.; Pidgeon, Anna M.; Thogmartin, Wayne E.; Radeloff, Volker C.

2015-01-01

The onset of spring plant growth has shifted earlier in the year over the past several decades due to rising global temperatures. Earlier spring onset may cause phenological mismatches between the availability of plant resources and dependent animals, and potentially lead to more false springs, when subsequent freezing temperatures damage new plant growth. We used the extended spring indices to project changes in spring onset, defined by leaf out and by first bloom, and predicted false springs until 2100 in the conterminous United States (US) using statistically-downscaled climate projections from the Coupled Model Intercomparison Project 5 ensemble. Averaged over our study region, the median shift in spring onset was 23 days earlier in the Representative Concentration Pathway 8.5 scenario with particularly large shifts in the Western US and the Great Plains. Spatial variation in phenology was due to the influence of short-term temperature changes around the time of spring onset versus season long accumulation of warm temperatures. False spring risk increased in the Great Plains and portions of the Midwest, but remained constant or decreased elsewhere. We conclude that global climate change may have complex and spatially variable effects on spring onset and false springs, making local predictions of change difficult.

Gas emissions, minerals, and tars associated with three coal fires, Powder River Basin, USA.

Science.gov (United States)

Engle, Mark A; Radke, Lawrence F; Heffern, Edward L; O'Keefe, Jennifer M K; Hower, James C; Smeltzer, Charles D; Hower, Judith M; Olea, Ricardo A; Eatwell, Robert J; Blake, Donald R; Emsbo-Mattingly, Stephen D; Stout, Scott A; Queen, Gerald; Aggen, Kerry L; Kolker, Allan; Prakash, Anupma; Henke, Kevin R; Stracher, Glenn B; Schroeder, Paul A; Román-Colón, Yomayra; ter Schure, Arnout

2012-03-15

Ground-based surveys of three coal fires and airborne surveys of two of the fires were conducted near Sheridan, Wyoming. The fires occur in natural outcrops and in abandoned mines, all containing Paleocene-age subbituminous coals. Diffuse (carbon dioxide (CO(2)) only) and vent (CO(2), carbon monoxide (CO), methane, hydrogen sulfide (H(2)S), and elemental mercury) emission estimates were made for each of the fires. Additionally, gas samples were collected for volatile organic compound (VOC) analysis and showed a large range in variation between vents. The fires produce locally dangerous levels of CO, CO(2), H(2)S, and benzene, among other gases. At one fire in an abandoned coal mine, trends in gas and tar composition followed a change in topography. Total CO(2) fluxes for the fires from airborne, ground-based, and rate of fire advancement estimates ranged from 0.9 to 780mg/s/m(2) and are comparable to other coal fires worldwide. Samples of tar and coal-fire minerals collected from the mouth of vents provided insight into the behavior and formation of the coal fires. Published by Elsevier B.V.

Neutron Scattering from fcc Pr and Pr3Tl

DEFF Research Database (Denmark)

Birgeneau, R. J.; Als-Nielsen, Jens Aage; Bucher, E.

1972-01-01

Elastic-neutron-scattering measurements on the singlet-ground-state ferromagnets fcc Pr and Pr3 Tl are reported. Both exhibit magnetic phase transitions, possibly to a simple ferromagnetic state at 20 and 11.6 °K, respectively. The transitions appear to be of second order although that in fcc Pr...

PAH concentrations in lake sediment decline following ban on coal-tar-based pavement sealants in Austin, Texas

Science.gov (United States)

Van Metre, Peter C.; Mahler, Barbara J.

2013-01-01

Recent studies have concluded that coal-tar-based pavement sealants are a major source of polycyclic aromatic hydrocarbons (PAHs) in urban settings in large parts of the United States. In 2006, Austin, TX, became the first jurisdiction in the U.S. to ban the use of coal-tar sealants. We evaluated the effect of Austin’s ban by analyzing PAHs in sediment cores and bottom-sediment samples collected in 1998, 2000, 2001, 2012, and 2014 from Lady Bird Lake, the principal receiving water body for Austin urban runoff. The sum concentration of the 16 EPA Priority Pollutant PAHs (∑PAH16) in dated core intervals and surficial bottom-sediment samples collected from sites in the lower lake declined about 44% from 1998–2005 to 2006–2014 (means of 7980 and 4500 μg kg–1, respectively), and by 2012–2014, the decline was about 58% (mean of 3320 μg kg–1). Concentrations of ∑PAH16 in bottom sediment from two of three mid-lake sites decreased by about 71 and 35% from 2001 to 2014. Concentrations at a third site increased by about 14% from 2001 to 2014. The decreases since 2006 reverse a 40-year (1959–1998) upward trend. Despite declines in PAH concentrations, PAH profiles and source-receptor modeling results indicate that coal-tar sealants remain the largest PAH source to the lake, implying that PAH concentrations likely will continue to decline as stocks of previously applied sealant gradually become depleted.

Johannes Hindi tütar Pille Pae : inimlik headus ei sõltu rezhiimist / Pille Pae ; interv. Anneli Ammas

Index Scriptorium Estoniae

Pae, Pille

2006-01-01

Desintegraatori juhi Johannes Hindi tütar Pille Pae vastab küsimustele, mis puudutavad tema isa armuandmispalve esitamist, isale toetusallkirjade kogumist ning Arnold Rüütli suhteid Johannes Hindiga. Lisa: Kes oli Johannes Hint ja mis Desintegraator?

Thermal remediation of tar-contaminated soil and oil-contaminated gravel

International Nuclear Information System (INIS)

Anthony, E.J.; Wang, J.

2005-01-01

High temperature treatments are commonly considered for the decontamination of soil as they have the advantages of reliability, high capacity, and effective destruction of hazardous materials with reduced long-term liability. This paper examined the remediation of soil contaminated by coal tar as well as gravel contaminated by oil. Pilot plant studies were conducted using 2 representative incineration technologies: rotary kiln and fluidized bed. The coal tar contaminated soil had accumulated over a few decades at a calcination plant in western Canada. The soil was sticky and could not be handled by conventional feeding and combustion systems. Crushed lignite was mixed with the soil as an auxiliary fuel and to reduce stickiness. A pilot plant furnace was used to evaluate the potential of decontamination in a rotary calciner. An analysis of both a modelling study and the test results showed that complete decontamination could be achieved in the targeted calciner. The results suggested that energy recovery was also possible, which could in turn make the remediation process more cost-effective. Decontamination of oil-contaminated gravel was conducted with a pilot plant fluidized bed combustor to study the feasibility of using incineration technology in the remediation of gravel and debris contaminated by oil spills. Results indicated that the gravel was decontaminated with acceptable emission performance. It was concluded that the study will be valuable to the application of commercial incineration processes for the remediation of polluted soils. It was observed that the weathering of the oiled gravel lowered the rate of decontamination. A small amount of salt water resulted in lowered decontamination rates, which may be an important factor for situations involving the remediation of shoreline gravel contaminated by oil. 24 refs., 6 tabs., 7 figs

Ground water monitoring strategies at the Weldon Spring Site, Weldon Spring, Missouri

International Nuclear Information System (INIS)

Meyer, K.A. Jr.

1988-01-01

This paper presents ground water monitoring strategies at the Weldon Spring Site in east-central Missouri. The Weldon Spring Site is a former ordnance works and uranium processing facility. In 1987, elevated levels of inorganic anions and nitroaromatics were detected in ground water beneath the site. Studies are currently underway to characterize the hydrogeologic regime and to define ground water contamination. The complex hydrogeology at the Weldon Spring Site requires innovative monitoring strategies. Combinations of fracture and conduit flow exist in the limestone bedrock. Perched zones are also present near surface impoundments. Losing streams and springs surround the site. Solving this complex combination of hydrogeologic conditions is especially challenging

Optimum Design of a Coil Spring for Improving the Performance of a Spring -Operated Mechanism

International Nuclear Information System (INIS)

Lee, Dae Woo; Sohn, Jeong Hyun; Yoo, Wan Suk

2016-01-01

In this study, a release test bed is designed to evaluate the dynamic behaviors of a coil spring. From the release tests, the dynamic behaviors of a coil spring are analyzed. A lumped parameter spring model was established for numerical simulation of a spring. The design variables of a coil spring are optimized by using the design of experiments approach. Two-level factorial designs are used for the design optimization, and the primary effects of the design variables are analyzed. Based on the results of the interaction analysis and design sensitivity analysis, the level of the design variables is rearranged. Finally, the mixed-level factorial design is used for the optimum design process. According to the optimum design of the opening spring, the dynamic performance of the spring-operated mechanism increases by 2.90

Hot springs in Hokuriku District

Energy Technology Data Exchange (ETDEWEB)

Sato, K. (Hot Springs Research Center, Japan)

1971-01-01

In the Hokuriku district including Toyama, Ishikawa, and Fukui Prefectures, hot springs of more than 25/sup 0/C were investigated. In the Toyama Prefecture, there are 14 hot springs which are located in an area from the Kurobe River to the Tateyama volcano and in the mountainous area in the southwest. In Ishikawa Prefecture there are 16 hot springs scattered in Hakusan and its vicinity, the Kaga mountains, and in the Noto peninsula. In northern Fukui Prefecture there are seven hot springs. The hot springs in Shirakawa in Gifu Prefecture are characterized as acid springs producing exhalations and H/sub 2/S. These are attributed to the Quaternary volcanoes. The hot springs of Wakura, Katayamazu, and Awara in Ishikawa Prefecture are characterized by a high Cl content which is related to Tertiary andesite. The hot springs of Daishoji, Yamanaka, Yamashiro, Kuritsu, Tatsunokuchi, Yuwaku, and Yunotani are characterized by a low HCO/sub 3/ content. The Ca and SO/sub 4/ content decreases from east to west, and the Na and Cl content increases from west to east. These fluctuations are related to the Tertiary tuff and rhyolite. The hot springs of Kuronagi, Kinshu, and Babadani, located along the Kurobe River are characterized by low levels of dissolved components and high CO/sub 2/ and HCO/sub 3/ content. These trends are related to late Paleozoic granite. Hot springs resources are considered to be connected to geothermal resources. Ten tables, graphs, and maps are provided.

Concentrations of polycyclic aromatic hydrocarbons (PAHs) and azaarenes in runoff from coal-tar- and asphalt-sealcoated pavement.

Science.gov (United States)

Mahler, Barbara J; Van Metre, Peter C; Foreman, William T

2014-05-01

Coal-tar-based sealcoat, used extensively on parking lots and driveways in North America, is a potent source of PAHs. We investigated how concentrations and assemblages of PAHs and azaarenes in runoff from pavement newly sealed with coal-tar-based (CT) or asphalt-based (AS) sealcoat changed over time. Samples of simulated runoff were collected from pavement 5 h to 111 d following application of AS or CT sealcoat. Concentrations of the sum of 16 PAHs (median concentrations of 328 and 35 μg/L for CT and AS runoff, respectively) in runoff varied relatively little, but rapid decreases in concentrations of azaarenes and low molecular weight PAHs were offset by increases in high molecular weight PAHs. The results demonstrate that runoff from CT-sealcoated pavement, in particular, continues to contain elevated concentrations of PAHs long after a 24-h curing time, with implications for the fate, transport, and ecotoxicological effects of contaminants in runoff from CT-sealcoated pavement. Published by Elsevier Ltd.

Concentrations of polycyclic aromatic hydrocarbons (PAHs) and azaarenes in runoff from coal-tar- and asphalt-sealcoated pavement

Science.gov (United States)

Mahler, Barbara J.; Van Metre, Peter C.; Foreman, William T.

2014-01-01

Coal-tar-based sealcoat, used extensively on parking lots and driveways in North America, is a potent source of PAHs. We investigated how concentrations and assemblages of PAHs and azaarenes in runoff from pavement newly sealed with coal-tar-based (CT) or asphalt-based (AS) sealcoat changed over time. Samples of simulated runoff were collected from pavement 5 h to 111 d following application of AS or CT sealcoat. Concentrations of the sum of 16 PAHs (median concentrations of 328 and 35 μg/L for CT and AS runoff, respectively) in runoff varied relatively little, but rapid decreases in concentrations of azaarenes and low molecular weight PAHs were offset by increases in high molecular weight PAHs. The results demonstrate that runoff from CT-sealcoated pavement, in particular, continues to contain elevated concentrations of PAHs long after a 24-h curing time, with implications for the fate, transport, and ecotoxicological effects of contaminants in runoff from CT-sealcoated pavement.

Mass Transfer Coefficientin Stirred Tank for p -Cresol Extraction Process from Coal Tar

International Nuclear Information System (INIS)

Fardhyanti, D S; Tyaningsih, D S; Afifah, S N

2017-01-01

Indonesia is a country that has a lot of coal resources. The Indonesian coal has a low caloric value. Pyrolysis is one of the process to increase the caloric value. One of the by-product of the pyrolysis process is coal tar. It contains a lot of aliphatic or aromatic compounds such as p -cresol (11% v/v). It is widely used as a disinfectant. Extractionof p -Cresol increases the economic value of waste of coal. The aim of this research isto study about mass tranfer coefficient in the baffled stirred tank for p -Cresolextraction from coal tar. Mass transfer coefficient is useful for design and scale up of industrial equipment. Extraction is conducted in the baffled stirred tank equipped with a four-bladed axial impeller placed vertically in the vessel. Sample for each time processing (5, 10, 15, 20, 25 and 30minutes) was poured into a separating funnel, settled for an hour and separated into two phases. Then the two phases were weighed. The extract phases and raffinate phases were analyzed by Spectronic UV-Vis. The result showed that mixing speed of p -Cresol extraction increasesthe yield of p -Cresol and the mass transfer coefficient. The highest yield of p -Cresol is 49.32% and the highest mass transfer coefficient is 4.757 x 10 -6 kg/m 2 s. (paper)

Mass Transfer Coefficientin Stirred Tank for p-Cresol Extraction Process from Coal Tar

Science.gov (United States)

Fardhyanti, D. S.; Tyaningsih, D. S.; Afifah, S. N.

2017-04-01

Indonesia is a country that has a lot of coal resources. The Indonesian coal has a low caloric value. Pyrolysis is one of the process to increase the caloric value. One of the by-product of the pyrolysis process is coal tar. It contains a lot of aliphatic or aromatic compounds such asp-cresol (11% v/v). It is widely used as a disinfectant. Extractionof p-Cresol increases the economic value of waste of coal. The aim of this research isto study about mass tranfer coefficient in the baffled stirred tank for p-Cresolextraction from coal tar. Mass transfer coefficient is useful for design and scale up of industrial equipment. Extraction is conducted inthe baffled stirred tank equipped with a four-bladed axial impeller placed vertically in the vessel. Sample for each time processing (5, 10, 15, 20, 25 and 30minutes) was poured into a separating funnel, settled for an hour and separated into two phases. Then the two phases were weighed. The extract phases and raffinate phases were analyzed by Spectronic UV-Vis. The result showed that mixing speed of p-Cresol extraction increasesthe yield of p-Cresol and the mass transfer coefficient. The highest yield of p-Cresol is 49.32% and the highest mass transfer coefficient is 4.757 x 10-6kg/m2s.

Isothermal sections of the state diagram for the Pr-Ni-Ge system at 870 (0-0,5Pr) and 670 K (0,5-1Pr)

International Nuclear Information System (INIS)

Fedyna, M.F.; Pecharskij, V.K.; Bodak, O.I.

1987-01-01

Method of X-ray phase and microstructural analyses were used to study Pr-Ni-Ge ternary system at 870K (0-0.50 at.fractions of Pr) and 670K (0.50-1.00 at.fractions of Pr). 11 ternary compounds exist in the system: Pr 1-x (NiGe) 13 (x=0.24), PrNi 2 Ge 2 , Pr 2 Ni 3 Ge 5 , PrNiGe 3 , Pr 2 NiGe 6 , Pr 3 Ni 4 Ge 4 , PrNi (1-x) Ge 2 (x=0.33), PrNiGe, Pr(NiGe) 2-x (x=0.14), Pr 3 NiGe 2 , ∼Pr 5 NiGe 4 . Crystal structure was determined for seven ternary compounds

Modelling of thermal removal of tars in a high temperature stage fed by a plasma torch

International Nuclear Information System (INIS)

Fourcault, A.; Marias, F.; Michon, U.

2010-01-01

The thermal degradation of tars in a chamber fed by a non-transferred plasma torch is theoretically examined in this study. The input of this reactor is a product gas coming from a gasification unit with a temperature of about 800 o C. According to literature, naphthalene and toluene are chosen as model compounds to represent the behaviour of their classes. According to this choice and to the data available in the literature, a reaction pathway for the thermal degradation of tars and its associated kinetics are proposed in this study. This mechanism is introduced in a CSTR model in order to check the influence of the operating parameters of the reactor on the degradation efficiency. These computations clearly show that a complete conversion of toluene (>99.9%) and an important conversion of naphthalene (96.7%) can be reached in the reactor, with concentration levels compatible with the further use of gas engines for electricity production. This theoretical study requires to be validated by comparison with experimental results.

Modelling of thermal removal of tars in a high temperature stage fed by a plasma torch

Energy Technology Data Exchange (ETDEWEB)

Fourcault, A. [Laboratoire Thermique Energetique et Procedes, LaTEP-ENSGTI, rue Jules Ferry, BP 7511, 64075 Pau Cedex (France); Europlasma, 21 rue Daugere, 33520 Bruges (France); Marias, F. [Laboratoire Thermique Energetique et Procedes, LaTEP-ENSGTI, rue Jules Ferry, BP 7511, 64075 Pau Cedex (France); Michon, U. [Europlasma, 21 rue Daugere, 33520 Bruges (France)

2010-09-15

The thermal degradation of tars in a chamber fed by a non-transferred plasma torch is theoretically examined in this study. The input of this reactor is a product gas coming from a gasification unit with a temperature of about 800 C. According to literature, naphthalene and toluene are chosen as model compounds to represent the behaviour of their classes. According to this choice and to the data available in the literature, a reaction pathway for the thermal degradation of tars and its associated kinetics are proposed in this study. This mechanism is introduced in a CSTR model in order to check the influence of the operating parameters of the reactor on the degradation efficiency. These computations clearly show that a complete conversion of toluene (>99.9%) and an important conversion of naphthalene (96.7%) can be reached in the reactor, with concentration levels compatible with the further use of gas engines for electricity production. This theoretical study requires to be validated by comparison with experimental results. (author)

Spheres of discharge of springs

Science.gov (United States)

Springer, Abraham E.; Stevens, Lawrence E.

2009-02-01

Although springs have been recognized as important, rare, and globally threatened ecosystems, there is as yet no consistent and comprehensive classification system or common lexicon for springs. In this paper, 12 spheres of discharge of springs are defined, sketched, displayed with photographs, and described relative to their hydrogeology of occurrence, and the microhabitats and ecosystems they support. A few of the spheres of discharge have been previously recognized and used by hydrogeologists for over 80 years, but others have only recently been defined geomorphologically. A comparison of these spheres of discharge to classification systems for wetlands, groundwater dependent ecosystems, karst hydrogeology, running waters, and other systems is provided. With a common lexicon for springs, hydrogeologists can provide more consistent guidance for springs ecosystem conservation, management, and restoration. As additional comprehensive inventories of the physical, biological, and cultural characteristics are conducted and analyzed, it will eventually be possible to associate spheres of discharge with discrete vegetation and aquatic invertebrate assemblages, and better understand the habitat requirements of rare or unique springs species. Given the elevated productivity and biodiversity of springs, and their highly threatened status, identification of geomorphic similarities among spring types is essential for conservation of these important ecosystems.

Studies on the applicability of biomarkers in estimating the systematic bioavailability of polynuclear aromatic hydrocarbons from manufactured gas plant tar-contaminated soils

International Nuclear Information System (INIS)

Koganti, A.; Spina, D.A.; Rozett, K.; Ma, B.-L.; Weyand, E.; Taylor, B.B.; Mauro, D.M.

1998-01-01

The systematic bioavailability of polynuclear aromatic hydrocarbons (PAH) from ingested soils containing manufactured gas plant (MGP) tar was evaluated in mice. Soil and organic extract of each soil were incorporated into a diet and fed to mice for two weeks. 1-Hydroxypyrene levels in urine and chemical:DNA adduct levels in lungs were used as biomarkers of PAH systematic bioavailability. Estimates of PAH relative bioavailability were determined by comparing the bioavailability observed between each soil and corresponding organic extract. In all but one case, bioavailiablity estimates based on 1-hydroxypyrene levels in urine indicate that the presence of MGP tar on soil results in a considerable decrease in PAH systemic bioavailablity (9-75%). Similarly, PAH bioavailability estimates based on chemical:DNA adduct formation ranged from nondetectable to 76%. These results clearly indicate that the bioavailiablity of PAH is less than 100% when soil contaminated with MGP tar is ingested by nice. In addition, the experimental methods employed in this study appear suitable for evaluating the effects of soil on the gastrointestinal absorption and systemic bioavailability of PAH from soil containing complex organic mixtures. 44 refs., 1 fig., 5 tabs

Biomass Waste Gasification – Can Be the Two Stage Process Suitable for Tar Reduction and Power Generation?

Czech Academy of Sciences Publication Activity Database

Šulc, J.; Štojdl, J.; Richter, M.; Popelka, J.; Svoboda, Karel; Smetana, J.; Vacek, J.; Skoblia, S.; Buryan, P.

2012-01-01

Roč. 32, č. 4 (2012), s. 692-700 ISSN 0956-053X Grant - others:RFCR(XE) CT-2010-00009 Institutional research plan: CEZ:AV0Z40720504 Keywords : waste biomass * gasification * tar Subject RIV: JE - Non-nuclear Energetics, Energy Consumption ; Use Impact factor: 2.485, year: 2012

Mechanical characterization of Portland cement mortars containing petroleum or coal tar

Directory of Open Access Journals (Sweden)

Garcés, P.

2007-08-01

Full Text Available This article discusses experimental data on the flexural and compressive strength of Portland cement mortars containing additions or cement replacements consisting in petroleum or coal tar, by-products of the oil and coal industries. The materials studied were two coal (BACA and BACB and two petroleum (BPP and BPT tars. The results show that it is feasible to use such materials as a partial replacement for cement in mortar manufacture. This should lead to the design of a new sustainable product that will contribute to lowering the environmental impact of construction materials while at the same time opening up an avenue for the re-use of this type of industrial by-products.En este artículo se presentan datos experimentales de resistencia a flexión y a compresión de morteros de cemento Portland con adición y sustitución de breas de petróleo y de alquitrán de carbón, que son subproductos de la industria del carbón o del petróleo. Los materiales estudiados son breas de alquitrán de carbón A (BACA y B (BACB, y dos breas de petróleo (BPP y (BPT. Los datos demuestran la viabilidad del uso de estas breas en la fabricación de morteros con menores contenidos de cemento, permitiendo diseñar un nuevo material sostenible con el medio ambiente y que contribuya a reducir el impacto ambiental de los materiales de construcción, hecho que permite abrir una nueva vía de valorización de estos subproductos.

Are PAHS the Right Metric for Assessing Toxicity Related to Oils, Tars, Creosote and Similar Contaminants in Sediments?

Science.gov (United States)

Oils, tars, and other non-aqueous phase hydrocarbon liquids (NAPLs) are common sources of contamination in aquatic sediments, and the toxicity of such contamination has generally been attributed to component chemicals, particularly PAHs. While there is no doubt PAHs can be toxic ...

Coil spring venting arrangement

International Nuclear Information System (INIS)

McCugh, R.M.

1975-01-01

A simple venting device for trapped gas pockets in hydraulic systems is inserted through a small access passages, operated remotely, and removed completely. The device comprises a small diameter, closely wound coil spring which is pushed through a guide temporarily inserted in the access passage. The guide has a central passageway which directs the coil spring radially upward into the pocket, so that, with the guide properly positioned for depth and properly oriented, the coil spring can be pushed up into the top of the pocket to vent it. By positioning a seal around the free end of the guide, the spring and guide are removed and the passage is sealed

Comparative spring mechanics in mantis shrimp.

Science.gov (United States)

Patek, S N; Rosario, M V; Taylor, J R A

2013-04-01

Elastic mechanisms are fundamental to fast and efficient movements. Mantis shrimp power their fast raptorial appendages using a conserved network of exoskeletal springs, linkages and latches. Their appendages are fantastically diverse, ranging from spears to hammers. We measured the spring mechanics of 12 mantis shrimp species from five different families exhibiting hammer-shaped, spear-shaped and undifferentiated appendages. Across species, spring force and work increase with size of the appendage and spring constant is not correlated with size. Species that hammer their prey exhibit significantly greater spring resilience compared with species that impale evasive prey ('spearers'); mixed statistical results show that species that hammer prey also produce greater work relative to size during spring loading compared with spearers. Disabling part of the spring mechanism, the 'saddle', significantly decreases spring force and work in three smasher species; cross-species analyses show a greater effect of cutting the saddle on the spring force and spring constant in species without hammers compared with species with hammers. Overall, the study shows a more potent spring mechanism in the faster and more powerful hammering species compared with spearing species while also highlighting the challenges of reconciling within-species and cross-species mechanical analyses when different processes may be acting at these two different levels of analysis. The observed mechanical variation in spring mechanics provides insights into the evolutionary history, morphological components and mechanical behavior, which were not discernible in prior single-species studies. The results also suggest that, even with a conserved spring mechanism, spring behavior, potency and component structures can be varied within a clade with implications for the behavioral functions of power-amplified devices.

Production and investigation of low-temperature coal tar. [Book in German

Energy Technology Data Exchange (ETDEWEB)

1953-01-01

Research into low-temperature carbonization has recently been stimulated because this process can be applied to coals that are not suitable for treatment by the usual high-temperature method. However, in spite of the value of the coke produced by low-temperature carbonization as a smokeless fuel, this process has not proved economical in Germany. Research has therefore been directed towards a more profitable utilization of the tar, and this government publication reports experiments on its detailed analysis by distillation and other methods. The book also includes descriptions of the various types of plant used for low-temperature carbonization and presents a brief history of the process.

Diversity of 16S rRNA and dioxygenase genes detected in coal-tar-contaminated site undergoing active bioremediation

Energy Technology Data Exchange (ETDEWEB)

Kumar, M; Khanna, S [NIIT Univ, Neemrana (India). Dept. of Biotechnology & Bioinformation

2010-04-15

In order to develop effective bioremediation strategies for polyaromatic hydrocarbons (PAHs) degradation, the composition and metabolic potential of microbial communities need to be better understood, especially in highly PAH contaminated sites in which little information on the cultivation-independent communities is available. Coal-tar-contaminated soil was collected, which consisted of 122-122.5 mg g{sup -1} total extractable PAH compounds. Biodegradation studies with this soil indicated the presence of microbial community that is capable of degrading the model PAH compounds viz naphthalene, phenanthrene and pyrene at 50 ppm each. PCR clone libraries were established from the DNA of the coal-tar-contaminated soil, targeting the 16S rRNA to characterize (I) the microbial communities, (ii) partial gene fragment encoding the Rieske iron sulfur center {alpha}-subunit) common to all PAH dioxygenase enzymes and (iii) {beta}-subunit of dioxygenase. Phylotypes related to Proteobacteria ({Alpha}-, {Epsilon}- and Gammaproteobacteria), Acidobacteria, Actinobacteria, Firmicutes, Gemmatimonadetes and Deinococci were detected in 16S rRNA derived clone libraries. Many of the gene fragment sequences of alpha-subunit and beta-subunit of dioxygenase obtained from the respective clone libraries fell into clades that are distinct from the reference dioxygenase gene sequences. Presence of consensus sequence of the Rieske type (2Fe2S) cluster binding site suggested that these gene fragments encode for {alpha}-subunit of dioxygenase gene. Sequencing of the cloned libraries representing {alpha}-subunit gene fragments (Rf1) and beta-subunit of dioxygenase showed the presence of hitherto unidentified dioxygenase in coal-tar-contaminated soil.

Occurrence of springs in massifs of crystalline rocks, northern Portugal

Science.gov (United States)

Pacheco, Fernando António Leal; Alencoão, Ana Maria Pires

2002-02-01

An inventory of artesian springs emerging from fractures (fracture springs) was conducted in the Pinhão River Basin and Morais Massif, northern Portugal, comprising an area of approximately 650 km2. Over 1,500 springs were identified and associated with geological domains and fracture sets. Using cross-tabulation analysis, spring distributions by fracture sets were compared among geological environments, and the deviations related to differences in rock structure and, presumably, to differences in deformational histories. The relation between spring frequencies and rock structures was further investigated by spectral determination, the model introduced in this study. Input data are the spring frequencies and fracture lengths in each geological domain, in addition to the angles between fracture strikes and present-day stress-field orientation (θ). The model's output includes the so-called intrinsic densities, a parameter indexing spring occurrence to factors such as fracture type and associated deformational regime and age. The highest densities (12.2 springs/km of lineament) were associated with young shear fractures produced by brittle deformation, and the lowest (0.1) with old tensional and ductile fractures. Spectral determination also relates each orientation class to a dominant structural parameter: where spring occurrence is controlled by θ, the class is parallel to the present-day stress-field orientation; where the control is attributed to the length of fractures, the spring occurrence follows the strike of large-scale normal faults crossing the region. Résumé. Un inventaire des sources artésiennes émergeant de fractures (sources de fractures) a été réalisé dans le bassin de la rivière Pinhão et dans le massif de Morais, dans le nord du Portugal, dans une région couvrant environ 650 km2. Plus de 1,500 sources ont été identifiées et associées à des domaines géologiques et à des ensembles de fractures. Grâce à une analyse de tableaux

Utilisation of the binders prepared from coal tar pitch and phenolic resins for the production metallurgical quality briquettes from coke breeze and the study of their high temperature carbonization behaviour

Energy Technology Data Exchange (ETDEWEB)

Benk, Ayse [University of Erciyes, Faculty of Art and Science, Department of Chemistry, 38039, Kayseri (Turkey)

2010-09-15

To reduce the cost of the formed coke briquettes which can be used as a substitute fuel to the metallurgical coke for the blast furnace from the coke breeze alternative binders and their blends were used. The high temperature behavior was investigated. The binders tested were: the nitrogen blown, air blown coal tar pitch and the blend of air blown coal tar pitch with the phenolic resins blends. The phenolic resin blends were prepared by mixing equal amount of resole and novalac. From the results, nitrogen blowing resulted in the weakest briquettes. The air blowing procedure should be preferred in place of nitrogen blowing for this purpose. When the air blown coal tar pitch was used alone as a binder, the briquettes must be cured at 200 C for 2 h, then carbonized at a temperature above 670 C. Since it requires higher temperature at carbonization stage, using air blown coal tar pitch alone as a binder was not economical. Therefore, the briquettes were prepared from the blended binder, containing air blown coal tar pitch and phenolic resins blend. The optimum amount of air blown coal tar pitch was found to be 50% w/w in the blended binder. Curing the briquettes at 200 C for 2 h was found to be sufficient for producing strong briquettes with a tensile strength of 50.45 MN/m{sup 2}. When these cured briquettes were carbonized at temperatures 470 C, 670 C and 950 C, their strength were increasing continuously, reaching to 71.85 MN/m{sup 2} at the carbonization temperature of 950 C. These briquettes can be used as a substitute for the metallurgical coke after curing; the process might not require un-economical high temperature carbonization stage. (author)

The use of coal-tar pitches of very high softening point and low carcinogen content as binders for industrial carbon

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

It has been demonstrated that the content of known carcinogenic polynuclear aromatic hydrocarbons (PAH) in coal-tar pitches may be reduced to levels which comply with existing and/or proposed environmental legislation, typically by distillation at low pressures, and preferably using a form of thin-film evaporation apparatus. However, the immediate products of such distillations usually have very high softening points, typically above 200{degree}C, and are unsuitable for direct utilization in conventional commercial carbon manufacturing processes as a result of the need for very high mixing temperatures. Advantage has been taken of the of a low-PAH coal-tar pitch, supplied in powder form, which has a softening point above 200{degree}C. Methods were examined which might allow mixing and forming of the hard pitch and a petroleum coke aggregate blend either at room temperature or at conventional processing temperature, and hot-pressuring or sintering procedures in which mixtures of the hard pitch and petroleum coke aggregate were formed at or above the softening temperature of the pitch. All the formed products were baked to give carbons which were evaluated for the major properties of density, electrical resistivity and strength. A comparison was also made between the volatiles evolved during the baking of products made with the low-PAH pitch and those made with a conventional coal-tar binder pitch.

Phase I study of concurrent radiotherapy with TS-1 and vitamin A (TAR therapy) for head and neck cancer

International Nuclear Information System (INIS)

Nakashima, Torahiko; Kuratomi, Yuichiro; Yamamoto, Tomoya; Masuda, Muneyuki; Hirakawa, Naoya; Nakamura, Kazumasa; Shioyama, Yoshiyuki; Umezaki, Toshiro; Komune, Shizuo

2005-01-01

The triple combination of 5-fluorouracil (5-FU), vitamin A and radiation (FAR therapy) has been effectively used to treat head and neck cancer. The biological anti-tumor effect of 5-FU depends on the activity of its metabolizing enzyme, dihydropyrimidine dehydrogenase (DPD). TS-1 is a novel oral DPD inhibitory fluoropyrimidine (DIF). To improve the anti-tumor effect of FAR therapy, we have applied TS-1 in place of 5-FU injection in the combination of Vitamin A and radiation (TAR therapy). In this study, we have examined the appropriate duration of TS-1 medication and the clinical efficacy and safety of TAR therapy. TS-1 was administered orally at a dose of 65 mg/m 2 twice a day. Vitamin A (Retinol Palmitate: 50,000 U/day) was administered intra-musculary on each day of radiation. Radiation was given (1.5∼2 Gy/day: 5 days/week) for 30∼40 Gy. The levels were divided according to the length of TS-1 application as follows: level 1, 2 weeks; level 2, 3 weeks; level 4, 4 weeks. Grade 4 toxicity of anorexia was observed in one case of level 3. We decided that level 2 (3 weeks of TS-1 administration) was the appropriate length of TS-1 application. TAR therapy is a useful concurrent chemo-radiotherapy which might improve the response rate and quality of life (QOL) of patients with head and neck squamous cell carcinoma (HNSCC). (author)

Suured prügifirmad valmistuvad prügipuuduseks / Mirko Ojakivi

Index Scriptorium Estoniae

Ojakivi, Mirko

2010-01-01

Ragn-Sells ja Adelan Prügiveod soovivad luba jäätmete pikaajaliseks vaheladestamiseks Tallinna piiril. Ragn-Sells saaks jäätmekütusetehase planeerimise ja ehitamise ajal endale koguda ligi 35 000 t segaolmejäätmeid aastas, Adelan Prügiveod sooviks ladestada ligi 50 000 t prügi aastas

Mockito for Spring

CERN Document Server

Acharya, Sujoy

2015-01-01

If you are an application developer with some experience in software testing and want to learn more about testing frameworks, then this technology and book is for you. Mockito for Spring will be perfect as your next step towards becoming a competent software tester with Spring and Mockito.

Rebound of a coal tar creosote plume following partial source zone treatment with permanganate.

Science.gov (United States)

Thomson, N R; Fraser, M J; Lamarche, C; Barker, J F; Forsey, S P

2008-11-14

The long-term management of dissolved plumes originating from a coal tar creosote source is a technical challenge. For some sites stabilization of the source may be the best practical solution to decrease the contaminant mass loading to the plume and associated off-site migration. At the bench-scale, the deposition of manganese oxides, a permanganate reaction byproduct, has been shown to cause pore plugging and the formation of a manganese oxide layer adjacent to the non-aqueous phase liquid creosote which reduces post-treatment mass transfer and hence mass loading from the source. The objective of this study was to investigate the potential of partial permanganate treatment to reduce the ability of a coal tar creosote source zone to generate a multi-component plume at the pilot-scale over both the short-term (weeks to months) and the long-term (years) at a site where there is >10 years of comprehensive synoptic plume baseline data available. A series of preliminary bench-scale experiments were conducted to support this pilot-scale investigation. The results from the bench-scale experiments indicated that if sufficient mass removal of the reactive compounds is achieved then the effective solubility, aqueous concentration and rate of mass removal of the more abundant non-reactive coal tar creosote compounds such as biphenyl and dibenzofuran can be increased. Manganese oxide formation and deposition caused an order-of-magnitude decrease in hydraulic conductivity. Approximately 125 kg of permanganate were delivered into the pilot-scale source zone over 35 days, and based on mass balance estimates 35% reduction for all monitored compounds except for biphenyl, dibenzofuran and fluoranthene 150 days after treatment, which is consistent with the bench-scale experimental results. Pre- and post-treatment soil core data indicated a highly variable and random spatial distribution of mass within the source zone and provided no insight into the mass removed of any of the

Crystal Field Levels of Pr3+ in PrFeO3 and PrGaO3 Determined by Inelastic Neutron Scattering

DEFF Research Database (Denmark)

Feldmann, K.; Henning, K.; Kaun, L.

1975-01-01

The crystal field splitting of the 3H4 ground state of the Pr ion in PrFeO3 and PrGaO3 has been investigated by inelastic scattering of thermal neutrons. At several temperatures the transitions have been measured by TAS and TOF methods for polycrystalline PrFeO3 and by the TOF method...... for polycrystalline PrGaO3. Energy level schemes which are different for these materials are given....

PrP N-terminal domain triggers PrPSc-like aggregation of Dpl

International Nuclear Information System (INIS)

Erlich, Paul; Cesbron, Jean-Yves; Lemaire-Vieille, Catherine; Curt, Aurelie; Andrieu, Jean-Pierre; Schoehn, Guy; Jamin, Marc; Gagnon, Jean

2008-01-01

Transmissible spongiform encephalopathies are fatal neurodegenerative disorders thought to be transmitted by self-perpetuating conformational conversion of a neuronal membrane glycoprotein (PrP C , for 'cellular prion protein') into an abnormal state (PrP Sc , for 'scrapie prion protein'). Doppel (Dpl) is a protein that shares significant biochemical and structural homology with PrP C . In contrast to its homologue PrP C , Dpl is unable to participate in prion disease progression or to achieve an abnormal PrP Sc -like state. We have constructed a chimeric mouse protein, composed of the N-terminal domain of PrP C (residues 23-125) and the C-terminal part of Dpl (residues 58-157). This chimeric protein displays PrP-like biochemical and structural features; when incubated in presence of NaCl, the α-helical monomer forms soluble β-sheet-rich oligomers which acquire partial resistance to pepsin proteolysis in vitro, as do PrP oligomers. Moreover, the presence of aggregates akin to protofibrils is observed in soluble oligomeric species by electron microscopy

Bi3+–Pr3+ energy transfer processes and luminescent properties of LuAG:Bi,Pr and YAG:Bi,Pr single crystalline films

International Nuclear Information System (INIS)

Zorenko, Y.; Gorbenko, V.; Savchyn, V.; Zorenko, T.; Nikl, M.; Mares, J.A.; Beitlerova, A.; Jary, V.

2013-01-01

Absorption, cathodoluminescence, excitation spectra of photoluminescence (PL) and PL decay kinetics were studied at 300 K for the double doped with Bi 3+ –Pr 3+ and separately doped with Bi 3+ and Pr 3+ Lu 3 Al 5 O 12 (LuAG) and Y 3 Al 5 O 12 (YAG) single crystalline film (SCF) phosphors grown by the liquid phase epitaxy method. The emission bands in the UV range arising from the intrinsic radiative transitions of Bi 3+ based centers, and emission bands in the visible range, related to the luminescence of excitons localized around Bi 3+ based centers, were identified both in Bi–Pr and Bi-doped LuAG and YAG SCFs. The energy transfer processes from the host lattice simultaneously to Bi 3+ and Pr 3+ ions and from Bi 3+ to Pr 3+ ions were investigated. Competition between Pr 3+ and Bi 3+ ions in the energy transfer processes from the LuAG and YAG hosts was evidenced. The strong decrease of the intensity of Pr 3+ luminescence both in LuAG:Pr and YAG:Pr SCFs phosphors, grown from Bi 2 O 3 flux, is observed due to the quenching influence of Bi 3+ flux related impurity. Due to overlap of the UV emission band of Bi 3+ centers with the f–d absorption bands of Pr 3+ ions in the UV range and the luminescence of excitons localized around Bi ions with the f–f absorption bands of Pr 3+ ions in the visible range, an effective energy transfer from Bi 3+ ions to Pr 3+ ions takes place in LuAG:Bi,Pr and YAG:Bi,Pr SCFs, resulting in the appearance of slower component in the decay kinetics of the Pr 3+ d–f luminescence. -- Highlights: • Bi and Pr doped film phosphor grown by liquid phase epitaxy method. • Energy transfer from Bi 3+ to Pr 3+ ions. • Strong quenching of the Pr 3+ luminescence by Bi 3+ co-dopant

Characterization of the hydrogeology of the sacred Gihon Spring, Jerusalem: a deteriorating urban karst spring

Science.gov (United States)

Amiel, Ronit Benami; Grodek, Tamir; Frumkin, Amos

2010-09-01

The Gihon Spring, Jerusalem, is important for the major monotheistic religions. Its hydrogeology and hydrochemistry is studied here in order to understand urbanization effects on karst groundwater resources, and promote better water management. High-resolution monitoring of the spring discharge, temperature and electrical conductivity, was performed, together with chemical and bacterial analysis. All these demonstrate a rapid response of the spring to rainfall events and human impact. A complex karst system is inferred, including conduit flow, fissure flow and diffuse flow. Electrical conductivity, Na+ and K+ values (2.0 mS/cm, 130 and 50 mg/l respectively) are very high compared to other nearby springs located at the town margins (0.6 mS/cm, 15 and <1 mg/l respectively), indicating considerable urban pollution in the Gihon area. The previously cited pulsating nature of the spring was not detected during the present high-resolution monitoring. This phenomenon may have ceased due to additional water sources from urban leakage and irrigation feeding the spring. The urbanization of the recharge catchment thus affects the spring water dramatically, both chemically and hydrologically. Appropriate measures should therefore be undertaken to protect the Gihon Spring and other karst aquifers threatened by rapid urbanization.

TAR (Theatre as Representation) as a Provocative Teaching Tool in School Administration: A Dramatized Inclusive Classroom Scenario

Science.gov (United States)

Meyer, Matthew J.; Young, David C.

2013-01-01

The following dramatized classroom scenario depicts a teacher struggling with the nature of an inclusive learning environment, with instructional leadership and supervision of instruction as the theoretical and practical backdrop. The purpose of this article is to demonstrate how the use of a TAR (theatre as representation) case study can be used…

Nakamura Ryûtarô’s Anime, Serial Experiments, Lain (1998

Directory of Open Access Journals (Sweden)

Tamae KOBAYASHI PRINDLE

2015-07-01

Full Text Available This paper introduces Nakamura Ryūtarō’s anime, Serial Experiments, Lain (1998 as a new type of anime, a genre nameable as an “expository anime”, for the reason that it creates a diachronic story out of a synchronic aspect of a certain field of science. The overarching topic of Experiments is electronics, focusing on the comparison between digital and analogue communication systems. Experiments unfolds the rationales, potentials, and effects of the two types of communication systems using the perceptions of the major character, a thirteen-year old girl, Rein, as well as other supporting characters.

Analytical aspects of the remediation of soil by wet oxidation - Characterisation of tar contaminants and their degradation products

DEFF Research Database (Denmark)

Thomsen, A.B.; Nielsen, T.; Plöger, A.

1999-01-01

Wet oxidation of tar compounds gives rise to a wide range of products. Due to the incorporation of oxygen, these products become increasingly more water soluble and the analytical strategy has to take into account the different physical/chemicalproperties of the compounds. An interplay between ga...

Colombeau algebra as a mathematical tool for investigating step load and step deformation of systems of nonlinear springs and dashpots

Science.gov (United States)

Průša, Vít; Řehoř, Martin; Tůma, Karel

2017-02-01

The response of mechanical systems composed of springs and dashpots to a step input is of eminent interest in the applications. If the system is formed by linear elements, then its response is governed by a system of linear ordinary differential equations. In the linear case, the mathematical method of choice for the analysis of the response is the classical theory of distributions. However, if the system contains nonlinear elements, then the classical theory of distributions is of no use, since it is strictly limited to the linear setting. Consequently, a question arises whether it is even possible or reasonable to study the response of nonlinear systems to step inputs. The answer is positive. A mathematical theory that can handle the challenge is the so-called Colombeau algebra. Building on the abstract result by Průša and Rajagopal (Int J Non-Linear Mech 81:207-221, 2016), we show how to use the theory in the analysis of response of nonlinear spring-dashpot and spring-dashpot-mass systems.

Robotic Transversus Abdominis Release (TAR: is it possible to offer minimally invasive surgery for abdominal wall complex defects?

Directory of Open Access Journals (Sweden)

MARIA VITÓRIA FRANÇA DO AMARAL

Full Text Available ABSTRACT We describe the preliminary national experience and the early results of the use of robotic surgery to perform the posterior separation of abdominal wall components by the Transversus Abdominis Release (TAR technique for the correction of complex defects of the abdominal wall. We performed the procedures between 04/2/2015 and 06/15/2015 and the follow-up time was up to six months, with a minimum of two months. The mean surgical time was five hours and 40 minutes. Two patients required laparoscopic re-intervention, since one developed hernia by peritoneal migration of the mesh and one had mesh extrusion. The procedure proved to be technically feasible, with a still long surgical time. Considering the potential advantages of robotic surgery and those related to TAR and the results obtained when these two techniques are associated, we conclude that they seem to be a good option for the correction of complex abdominal wall defects.

Urban assemblages: ANT and the examination of the city Ensamblajes urbanos: la TAR y el examen de la ciudad

Directory of Open Access Journals (Sweden)

Ignacio Farías

2011-03-01

Full Text Available

This article presents new research perspectives and analytical challenges that actor-network theory opens for urban studies. First, it reviews how the ANT principles of hybrid relationality and flat associativity are being adopted in urban studies to symmetrically expand the urban ecology to nonhumans and contest scalar conceptions of urban space and economy. Second, it proposes that ANT brings along an even more fundamental challenge related to the understanding of the city as a research object. While common understandings as a spatial object, political-economical entity and/or sociocultural form underlie its singular, stable and bounded character, ANT allows thinking the city as a multiple and decentered object. The notion of urban assemblages is introduced to account for the circulation and becoming of the city in multiple hybrid and translocal networks. Finally, it concludes by discussing some consequences of this examination of the city, especially the reassertion of the problem of complexity, especially urban complexity, if not as a starting point, then at least as a point of arrival for ANT.

Este artículo presenta nuevas perspectivas de investigación y desafíos analíticos que la teoría del actor-red (TAR abre para los estudios urbanos. En primer lugar, se revisan cómo los principios de relacionalidad híbrida y asociatividad plana de la TAR están siendo adoptados en los estudios urbanos para ampliar simétricamente la ecología urbana a no-humanos e impugnar concepciones escalares del espacio y economías urbanas. A continuación, se propone que la TAR trae consigo un desafío más fundamental relativo a la

Natural attenuation of aged tar-oil in soils: A case study from a former gas production site

Science.gov (United States)

Ivanov, Pavel; Eickhorst, Thilo; Wehrer, Markus; Georgiadis, Anna; Rennert, Thilo; Eusterhues, Karin; Totsche, Kai Uwe

2017-04-01

Contamination of soils with tar oil occurred on many industrial sites in Europe. The main source of such contamination has been former manufactured gas plants (MGP). As many of them were destroyed during the World War II or abandoned in the second half of the XXth century, the contamination is depleted in volatile and degradable hydrocarbons (HC) but enriched in the heavy oil fractions due to aging processes. We studied a small tar-oil spill in a former MGP reservoir basin. The tar-oil had a total petroleum hydrocarbon (TPH) content of 245 mg/g. At the margin of the spill, vegetation has started to overgrow and intensively root the tar-oil layer. This zone comprised the uppermost 5-7 cm of our profile and contained 28 mg/g of TPH (A-layer)- The layer below the root zone (7-15 cm) was the most contaminated, with 90 mg/g TPH (B-layer). The layer underneath (15-22 cm) had smaller concentrations of 16 mg/g TPH (C-layer). Further down in the profile (D-layer) we found only slightly higher TPH content than in the control samples (1,4 mg/g vs 0,6 mg/g). The polycyclic aromatic hydrocarbons analysis showed the same distribution throughout all layers with highest contents of the PAHs with 4-6 condensed aromatic rings. Direct cell count and extraction of microbial biomass showed that the highly contaminated soil layers A and B had 2-3 times more bacteria than the control soils. CARD-FISH analysis revealed that in samples from layers A and B Archaea were more abundant (12% opposing to 6-7% in control soil). Analysis of bacteria (tested for Alpha-, Beta-, Gamma- and Epsilonproteobacteria and Actinobacteria) showed the dominance of Alphaproteobacteria in the layer A and C both beneath and above the most contaminated layer B. The primers covered the whole microbial consortia in these two layers, leaving almost no unidentified cells. In the most contaminated layer B Alphaproteobacteria amounted only to 20% of the microbial consortium, and almost 40% of the cells remained

Executive summary: Weldon Spring Site Environmental Report for calendar year 1992. Weldon Spring Site Remedial Action Project, Weldon Spring, Missouri

Energy Technology Data Exchange (ETDEWEB)

1993-06-01

This report has been prepared to provide information about the public safety and environmental protection programs conducted by the Weldon Spring Site Remedial Action Project. The Weldon Spring site is located in southern St. Charles County, Missouri, approximately 48 km (30 mi) west of St. Louis. The site consists of two main areas, the Weldon Spring Chemical Plant and raffinate pits and the Weldon Spring Quarry. The objectives of the Site Environmental Report are to present a summary of data from the environmental monitoring program, to characterize trends and environmental conditions at the site, and to confirm compliance with environmental and health protection standards and requirements. The report also presents the status of remedial activities and the results of monitoring these activities to assess their impacts on the public and environment. The scope of the environmental monitoring program at the Weldon Spring site has changed since it was initiated. Previously, the program focused on investigations of the extent and level of contaminants in the groundwater, surface waters, buildings, and air at the site. In 1992, the level of remedial activities required monitoring for potential impacts of those activities, particularly on surface water runoff and airborne effluents. This report includes monitoring data from routine radiological and nonradiological sampling activities. These data include estimates of dose to the public from the Weldon Spring site; estimates of effluent releases; and trends in groundwater contaminant levels. Also, applicable compliance requirements, quality assurance programs, and special studies conducted in 1992 to support environmental protection programs are reviewed.

Recent trend of administration on hot springs

Energy Technology Data Exchange (ETDEWEB)

Okubo, Shigeru [Environment Agency, Tokyo (Japan)

1989-01-01

The Environmental Agency exercises jurisdiction over Hot Spring Act, and plans to protect the source of the hot spring and to utilize it appropriately. From the aspect of utilization, hot springs are widely used as a means to remedy chronic diseases and tourist spots besides places for recuperation and repose. Statistics on Japanese hot springs showed that the number of hot spring spots and utilized-fountainhead increased in 1987, compared with the number in 1986. Considering the utilized-headspring, the number of naturally well-out springs has stabilized for 10 years while power-operated springs have increased. This is because the demand of hot springs has grown as the number of users has increased. Another reason is to keep the amount of hot water by setting up the power facility as the welled-out amount has decreased. Major point of recent administration on the hot spring is to permit excavation and utilization of hot springs. Designation of National hot spring health resorts started in 1954 in order to ensure the effective and original use of hot springs and to promote the public use of them, for the purpose of arranging the sound circumstances of hot springs. By 1988, 76 places were designated. 4 figs., 3 tabs.

Johannes Hindi tütar Pille Pae : inimlik headus ei sõltu režiimist / Pille Pae ; interv. Anneli Ammas

Index Scriptorium Estoniae

Pae, Pille

2006-01-01

Desintegraatori juhi Johannes Hindi tütar Pille Pae vastab küsimustele, mis puudutavad tema isa armuandmispalve esitamist, isale toetusallkirjade kogumist, Arnold Rüütli suhteid Johannes Hindiga. Lisa: Kes oli Johannes Hint ja mis Desintegraator?

Process and apparatus for recovering of oil, bitumen, tar, resins, etc

Energy Technology Data Exchange (ETDEWEB)

1921-11-06

A process for recovering oil, bitumen, tar, and resins from oil shale, oil sands, Fuller's earth, peat, brown coal, mineral coal, and wood, through direct action of superheated steam on the material, is characterized by the fact that superheated steam with or without mixing of inert gases at a temperature, which lies below the decomposition temperature of the material being treated, is passed through the material with a high velocity. It leaves through nozzles, used in steam turbines. A method of carrying out the process in which solution medium is used for action on the material is characterized by the fact that solvents such as benzine and benzol are mixed with steam in different quantities.

Evaluation of the health risk resulting from exposure to polycyclic aromatic hydrocarbons in coal-tar shampoo

Energy Technology Data Exchange (ETDEWEB)

Mennes, W.C.; Van Veen, M.P.; Kroese, E.D.; Speijers, G.J.A.

1996-10-01

Shampoos may contain as much as 56 mg benzo(a)pyrene (BaP)/kg product. Based on a human dermal uptake study, it is plausible that BaP and other PAHs become systemically available after a single use of coal-tar shampoos. Because several PAHs, among which BaP are considered to be carcinogenic substances, the safety of these products has been questioned. Dermal exposure results in skin tumours, but after inhalatory or oral exposure besides to local tumour formation, systemic tumours are found as well. In this report, an estimate of external dermal exposure to BaP has been generated by application of a mathematical model. This estimate was the starting point in an assessment of the additional risk on local skin tumours after contact with a coal-tar shampoo containing 56 mg BaP/kg product. In this assessment it was assumed that this shampoo was used three times weekly. Four different risk estimates were derived, namely for contact times of 1 or 5 minutes per event and for life-time or 40 years of use. 4 tabs., 3 appendices, 15 refs.

Preparation and Characterization of Malaysian Dolomites as a Tar Cracking Catalyst in Biomass Gasification Process

Directory of Open Access Journals (Sweden)

M. A. A. Mohammed

2013-01-01

Full Text Available Three types of local Malaysian dolomites were characterized to investigate their suitability for use as tar-cracking catalysts in the biomass gasification process. The dolomites were calcined to examine the effect of the calcination process on dolomite’s catalytic activity and properties. The modifications undergone by dolomites consequent to thermal treatment were investigated using various analytical methods. Thermogravimetric and differential thermal analyses indicated that the dolomites underwent two stages of decomposition during the calcination process. The X-ray diffraction and Fourier-transform infrared spectra analyses showed that thermal treatment of dolomite played a significant role in the disappearance of the CaMg(CO32 phase, producing the MgO-CaO form of dolomite. The scanning electron microscopy microphotographs of dolomite indicated that the morphological properties were profoundly affected by the calcination process, which led to the formation of a highly porous surface with small spherical particles. In addition, the calcination of dolomite led to the elimination of carbon dioxide and increases in the values of the specific surface area and average pore diameter, as indicated by surface area analysis. The results showed that calcined Malaysian dolomites have great potential to be applied as tar-cracking catalysts in the biomass gasification process based on their favorable physical properties.

Spring security 3.x cookbook

CERN Document Server

Mankale, Anjana

2013-01-01

This book follows a cookbook style exploring various security solutions provided by Spring Security for various vulnerabilities and threat scenarios that web applications may be exposed to at the authentication and session level layers.This book is for all Spring-based application developers as well as Java web developers who wish to implement robust security mechanisms into web application development using Spring Security.Readers are assumed to have a working knowledge of Java web application development, a basic understanding of the Spring framework, and some knowledge of the fundamentals o

Geochemical and hydrologic data for wells and springs in thermal-spring areas of the Appalachians

Energy Technology Data Exchange (ETDEWEB)

Hobba, W.A. Jr.; Chemerys, J.C.; Fisher, D.W.; Pearson, F.J. Jr.

1976-07-01

Current interest in geothermal potential of thermal-spring areas in the Appalachians makes all data on thermal springs and wells in these areas valuable. Presented here without interpretive comment are maps showing selected springs and wells and tables of physical and chemical data pertaining to these wells and springs. The chemical tables show compositions of gases (oxygen, nitrogen, argon, methane, carbon dioxide, and helium), isotope contents (tritium, carbon (13), and oxygen (18)), trace and minor element chemical data, and the usual complete chemical data.

Genetic relationship of organic bases of the quinoline and isoquinoline series from lignite semicoking tars with the initial biological material

Energy Technology Data Exchange (ETDEWEB)

Platonov, V.V.; Proskuryakov, V.A.; Podshibyakin, S.I.; Domogatskii, V.V.; Shvykin, A.Y.; Shavyrina, O.A.; Chilachava, K.B. [Leo Tolstoy State Pedagog University, Tula (Russian Federation)

2002-07-01

The genetic relationship of quinoline and isoquinoline compounds present in semicoking tars of Kimovsk lignites (near-Moscow fields) with the initial vegetable material is discussed. Transformation pathways of the native compounds in the course of lignite formation are suggested.

Applying spatial analysis techniques to assess the suitability of multipurpose uses of spring water in the Jiaosi Hot Spring Region, Taiwan

Science.gov (United States)

Jang, Cheng-Shin

2016-04-01

The Jiaosi Hot Spring Region is located in northeastern Taiwan and is rich in geothermal springs. The geothermal development of the Jiaosi Hot Spring Region dates back to the 18th century and currently, the spring water is processed for various uses, including irrigation, aquaculture, swimming, bathing, foot spas, and recreational tourism. Because of the proximity of the Jiaosi Hot Spring Region to the metropolitan area of Taipei City, the hot spring resources in this region attract millions of tourists annually. Recently, the Taiwan government is paying more attention to surveying the spring water temperatures in the Jiaosi Hot Spring Region because of the severe spring water overexploitation, causing a significant decline in spring water temperatures. Furthermore, the temperature of spring water is a reliable indicator for exploring the occurrence and evolution of springs and strongly affects hydrochemical reactions, components, and magnitudes. The multipurpose uses of spring water can be dictated by the temperature of the water. Therefore, accurately estimating the temperature distribution of the spring water is critical in the Jiaosi Hot Spring Region to facilitate the sustainable development and management of the multipurpose uses of the hot spring resources. To evaluate the suitability of spring water for these various uses, this study spatially characterized the spring water temperatures of the Jiaosi Hot Spring Region by using ordinary kriging (OK), sequential Gaussian simulation (SGS), and geographical information system (GIS). First, variogram analyses were used to determine the spatial variability of spring water temperatures. Next, OK and SGS were adopted to model the spatial distributions and uncertainty of the spring water temperatures. Finally, the land use (i.e., agriculture, dwelling, public land, and recreation) was determined and combined with the estimated distributions of the spring water temperatures using GIS. A suitable development strategy

Spring Recipes A Problem-solution Approach

CERN Document Server

Long, Josh; Mak, Gary

2010-01-01

With over 3 Million users/developers, Spring Framework is the leading "out of the box" Java framework. Spring addresses and offers simple solutions for most aspects of your Java/Java EE application development, and guides you to use industry best practices to design and implement your applications. The release of Spring Framework 3 has ushered in many improvements and new features. Spring Recipes: A Problem-Solution Approach, Second Edition continues upon the bestselling success of the previous edition but focuses on the latest Spring 3 features for building enterprise Java applications.

Quarry geotechnical report for the Weldon Spring Site Remedial Action Project, Weldon Spring, Missouri

International Nuclear Information System (INIS)

1990-11-01

This report has been prepared for the United States Department of Energy's (DOE) Weldon Spring Site Remedial Action Project (WSSRAP) by the Project Management Contractor (PMC), which is MK-Ferguson Company (MK-Ferguson) with Jacobs Engineering Group (JEG) as its designated subcontractor. The Weldon Spring site (WSS) comprises the Weldon Spring quarry area and the Weldon Spring chemical plant and raffinate pit areas. This report presents the results of geotechnical investigations conducted during 1989--1990 at the proposed Weldon Spring quarry staging and water treatment facilities in the quarry area. The facilities are intended for treatment of water removed from the quarry area. An access road and a decontamination pad will be necessary for handling and transportation of bulk waste. Results of previous geotechnical investigations performed by other geoscience and environmental engineering firms in the quarry area, were reviewed, summarized and incorporated into this report. Well logging, stratigraphy data, piezometer data, elevations, and soil characteristics are also included

Interaction between Shadoo and PrP Affects the PrP-Folding Pathway.

Science.gov (United States)

Ciric, Danica; Richard, Charles-Adrien; Moudjou, Mohammed; Chapuis, Jérôme; Sibille, Pierre; Daude, Nathalie; Westaway, David; Adrover, Miguel; Béringue, Vincent; Martin, Davy; Rezaei, Human

2015-06-01

Prion diseases are characterized by conformational changes of a cellular prion protein (PrP(C)) into a β-sheet-enriched and aggregated conformer (PrP(Sc)). Shadoo (Sho), a member of the prion protein family, is expressed in the central nervous system (CNS) and is highly conserved among vertebrates. On the basis of histoanatomical colocalization and sequence similarities, it is suspected that Sho and PrP may be functionally related. The downregulation of Sho expression during prion pathology and the direct interaction between Sho and PrP, as revealed by two-hybrid analysis, suggest a relationship between Sho and prion replication. Using biochemical and biophysical approaches, we demonstrate that Sho forms a 1:1 complex with full-length PrP with a dissociation constant in the micromolar range, and this interaction consequently modifies the PrP-folding pathway. Using a truncated PrP that mimics the C-terminal C1 fragment, an allosteric binding behavior with a Hill number of 4 was observed, suggesting that at least a tetramerization state occurs. A cell-based prion titration assay performed with different concentrations of Sho revealed an increase in the PrP(Sc) conversion rate in the presence of Sho. Collectively, our observations suggest that Sho can affect the prion replication process by (i) acting as a holdase and (ii) interfering with the dominant-negative inhibitor effect of the C1 fragment. Since the inception of the prion theory, the search for a cofactor involved in the conversion process has been an active field of research. Although the PrP interactome presents a broad landscape, candidates corresponding to specific criteria for cofactors are currently missing. Here, we describe for the first time that Sho can affect PrP structural dynamics and therefore increase the prion conversion rate. A biochemical characterization of Sho-PrP indicates that Sho acts as an ATP-independent holdase. Copyright © 2015, American Society for Microbiology. All Rights

Recombinant PrPSc shares structural features with brain-derived PrPSc: Insights from limited proteolysis.

Science.gov (United States)

Sevillano, Alejandro M; Fernández-Borges, Natalia; Younas, Neelam; Wang, Fei; R Elezgarai, Saioa; Bravo, Susana; Vázquez-Fernández, Ester; Rosa, Isaac; Eraña, Hasier; Gil, David; Veiga, Sonia; Vidal, Enric; Erickson-Beltran, Melissa L; Guitián, Esteban; Silva, Christopher J; Nonno, Romolo; Ma, Jiyan; Castilla, Joaquín; R Requena, Jesús

2018-01-01

Very solid evidence suggests that the core of full length PrPSc is a 4-rung β-solenoid, and that individual PrPSc subunits stack to form amyloid fibers. We recently used limited proteolysis to map the β-strands and connecting loops that make up the PrPSc solenoid. Using high resolution SDS-PAGE followed by epitope analysis, and mass spectrometry, we identified positions ~116/118, 133-134, 141, 152-153, 162, 169 and 179 (murine numbering) as Proteinase K (PK) cleavage sites in PrPSc. Such sites likely define loops and/or borders of β-strands, helping us to predict the threading of the β-solenoid. We have now extended this approach to recombinant PrPSc (recPrPSc). The term recPrPSc refers to bona fide recombinant prions prepared by PMCA, exhibiting infectivity with attack rates of ~100%. Limited proteolysis of mouse and bank vole recPrPSc species yielded N-terminally truncated PK-resistant fragments similar to those seen in brain-derived PrPSc, albeit with varying relative yields. Along with these fragments, doubly N- and C-terminally truncated fragments, in particular ~89/97-152, were detected in some recPrPSc preparations; similar fragments are characteristic of atypical strains of brain-derived PrPSc. Our results suggest a shared architecture of recPrPSc and brain PrPSc prions. The observed differences, in particular the distinct yields of specific PK-resistant fragments, are likely due to differences in threading which result in the specific biochemical characteristics of recPrPSc. Furthermore, recombinant PrPSc offers exciting opportunities for structural studies unachievable with brain-derived PrPSc.

Pr-magnetism in the quasi-skutterudite compound PrFe2Al8.

Science.gov (United States)

Nair, Harikrishnan S; Ogunbunmi, Michael O; Kumar, C M N; Adroja, D T; Manuel, P; Fortes, D; Taylor, J; Strydom, A M

2017-08-31

The intermetallic compound PrFe 2 Al 8 that possesses a three-dimensional network structure of Al polyhedra centered at the transition metal element Fe and the rare earth Pr is investigated through neutron powder diffraction and inelastic neutron scattering in order to elucidate the magnetic ground state of Pr and Fe and the crystal field effects of Pr. Our neutron diffraction study confirms long-range magnetic order of Pr below [Formula: see text] K in this compound. Subsequent magnetic structure estimation reveals a magnetic propagation vector [Formula: see text] with a magnetic moment value of [Formula: see text]/Pr along the orthorhombic c-axis and evidence the lack of ordering in the Fe sublattice. The inelastic neutron scattering study reveals one crystalline electric field excitation near 19 meV at 5 K in PrFe 2 Al 8 . The energy-integrated intensity of the 19 meV excitation as a function of [Formula: see text] follows the square of the magnetic form factor of [Formula: see text] thereby confirming that the inelastic excitation belongs to the Pr sublattice. The second sum rule applied to the dynamic structure factor indicates only 1.6(2) [Formula: see text] evolving at the 19 meV peak compared to the 3.58 [Formula: see text] for free [Formula: see text], indicating that the crystal field ground state is magnetic and the missing moment is associated with the resolution limited quasi-elastic line. The magnetic order occurring in Pr in PrFe 2 Al 8 is counter-intuitive to the symmetry-allowed crystal field level scheme, hence, is suggestive of exchange-mediated mechanisms of ordering stemming from the magnetic ground state of the crystal field levels.

Spring/dimple instrument tube restraint

International Nuclear Information System (INIS)

DeMario, E.E.; Lawson, C.N.

1993-01-01

A nuclear fuel assembly for a pressurized water nuclear reactor has a spring and dimple structure formed in a non-radioactive insert tube placed in the top of a sensor receiving instrumentation tube thimble disposed in the fuel assembly and attached at a top nozzle, a bottom nozzle, and intermediate grids. The instrumentation tube thimble is open at the top, where the sensor or its connection extends through the cooling water for coupling to a sensor signal processor. The spring and dimple insert tube is mounted within the instrumentation tube thimble and extends downwardly adjacent the top. The springs and dimples restrain the sensor and its connections against lateral displacement causing impact with the instrumentation tube thimble due to the strong axial flow of cooling water. The instrumentation tube has a stainless steel outer sleeve and a zirconium alloy inner sleeve below the insert tube adjacent the top. The insert tube is relatively non-radioactivated inconel alloy. The opposed springs and dimples are formed on diametrically opposite inner walls of the insert tube, the springs being formed as spaced axial cuts in the insert tube, with a web of the insert tube between the cuts bowed radially inwardly for forming the spring, and the dimples being formed as radially inward protrusions opposed to the springs. 7 figures

State diagram of Pr-Bi system

International Nuclear Information System (INIS)

Abulkhaev, V.L.; Ganiev, I.N.

1994-01-01

By means of thermal differential analysis, X-ray and microstructural analysis the state diagram of Pr-Bi system was studied. Following intermetallic compounds were defined in the system: Pr 2 Bi, Pr 5 Bi 3 , Pr 4 Bi 3 , Pr Bi, PrBi 2 , Pr 2 Bi, Pr 5 Bi 3 , Pr 4 Bi 3 and PrBi 2 . The data analysis on Ln-Bi diagram allowed to determine the regularity of change of properties of intermetallic compounds in the line of rare earth elements of cerium subgroup.

[History of hot spring bath treatment in China].

Science.gov (United States)

Hao, Wanpeng; Wang, Xiaojun; Xiang, Yinghong; Gu Li, A Man; Li, Ming; Zhang, Xin

2011-07-01

As early as the 7th century B.C. (Western Zhou Dynasty), there is a recording as 'spring which contains sulfur could treat disease' on the Wentang Stele written by WANG Bao. Wenquan Fu written by ZHANG Heng in the Easten Han Dynasty also mentioned hot spring bath treatment. The distribution of hot springs in China has been summarized by LI Daoyuan in the Northern Wei Dynasty in his Shuijingzhu which recorded hot springs in 41 places and interpreted the definition of hot spring. Bencao Shiyi (by CHEN Cangqi, Tang Dynasty) discussed the formation of and indications for hot springs. HU Zai in the Song Dynasty pointed out distinguishing hot springs according to water quality in his book Yuyin Conghua. TANG Shenwei in the Song Dynasty noted in Jingshi Zhenglei Beiji Bencao that hot spring bath treatment should be combined with diet. Shiwu Bencao (Ming Dynasty) classified hot springs into sulfur springs, arsenicum springs, cinnabar springs, aluminite springs, etc. and pointed out their individual indications. Geologists did not start the work on distribution and water quality analysis of hot springs until the first half of the 20th century. There are 972 hot springs in Wenquan Jiyao (written by geologist ZHANG Hongzhao and published in 1956). In July 1982, the First National Geothermal Conference was held and it reported that there were more than 2600 hot springs in China. Since the second half of the 20th century, hot spring sanatoriums and rehabilitation centers have been established, which promoted the development of hot spring bath treatment.

Identification of sources of tar balls deposited along the Goa coast, India, using fingerprinting techniques

Digital Repository Service at National Institute of Oceanography (India)

Suneel, V.; Vethamony, P.; Zakaria, M.P.; Naik, B.G.; Prasad, K.V.

. Christensen et al (2007) reviewed the practical aspects of chemometrics for oil spill fingerprinting and provided a basis for the use of chemometric 3    methods in tiered oil spill fingerprinting. Biomarker compounds such as isoprenoid alkanes, hopanes... deposited along the Malaysian beaches. Low molecular weight/high molecular weight ratios (L/H) of both alkanes and PAHs together are useful in categorizing the weathering effects of tar balls (Chandru et al., 2008). However, in cases...

Nuclear reactor spring strip grid spacer

International Nuclear Information System (INIS)

Patterson, J.F.; Flora, B.S.

1978-01-01

A bimetallic grid spacer is described comprising a grid structure of zircaloy formed by intersecting striplike members which define fuel element openings for receiving fuel elements and spring strips made of Inconel positioned within the grid structure for cooperating with the fuel elements to maintain them in their desired position. A plurality of these spring strips extend longitudinally between sides of the grid structure, being locked in position by the grid retaining strips. The fuel rods, which are disposed in the fuel openings formed in the grid structure, are positioned by means of the springs associated with the spring strips and a plurality of dimples which extend from the zircaloy grid structure into the openings. In one embodiment the strips are disposed in a plurality of arrays with those spring strip arrays situated in opposing diagonal quadrants of the grid structure extending in the same direction and adjacent spring strip arrays in each half of the spacer extending in relatively perpendicular directions. Other variations of the spring strip arrangements for a particular fuel design are disclosed herein

Prion protein (PrP) gene-knockout cell lines: insight into functions of the PrP

Science.gov (United States)

Sakudo, Akikazu; Onodera, Takashi

2015-01-01

Elucidation of prion protein (PrP) functions is crucial to fully understand prion diseases. A major approach to studying PrP functions is the use of PrP gene-knockout (Prnp−/−) mice. So far, six types of Prnp−/− mice have been generated, demonstrating the promiscuous functions of PrP. Recently, other PrP family members, such as Doppel and Shadoo, have been found. However, information obtained from comparative studies of structural and functional analyses of these PrP family proteins do not fully reveal PrP functions. Recently, varieties of Prnp−/− cell lines established from Prnp−/− mice have contributed to the analysis of PrP functions. In this mini-review, we focus on Prnp−/− cell lines and summarize currently available Prnp−/− cell lines and their characterizations. In addition, we introduce the recent advances in the methodology of cell line generation with knockout or knockdown of the PrP gene. We also discuss how these cell lines have provided valuable insights into PrP functions and show future perspectives. PMID:25642423

Prion protein (PrP) gene-knockout cell lines: insight into functions of the PrP

OpenAIRE

Sakudo, Akikazu; Onodera, Takashi

2015-01-01

Elucidation of prion protein (PrP) functions is crucial to fully understand prion diseases. A major approach to studying PrP functions is the use of PrP gene-knockout (Prnp ?/?) mice. So far, six types of Prnp ?/? mice have been generated, demonstrating the promiscuous functions of PrP. Recently, other PrP family members, such as Doppel and Shadoo, have been found. However, information obtained from comparative studies of structural and functional analyses of these PrP family proteins do not ...

Mineralization of PAHs in coal-tar impacted aquifer sediments and associated microbial community structure investigated with FISH

Energy Technology Data Exchange (ETDEWEB)

Rogers, S W; Ong, S K; Moorman, T B [Iowa State University, Ames, IA (USA)

2007-11-15

The microbial community structure and mineralization of polycyclic aromatic hydrocarbons (PAHs) in a coal-tar contaminated aquifer were investigated spatially using fluorescence in situ hybridization (FISH) and in laboratory-scale incubations of the aquifer sediments. DAPI-detected microbial populations in the contaminated sediments were three orders of magnitude greater than nearby uncontaminated sediments, suggesting growth on coal-tar constituents in situ. Actinobacteria, {beta}- and {gamma}-Proteobacteria, and Flavobacteria dominated the in situ aerobic (> 1 mg l{sup -1} dissolved oxygen) microbial community, whereas sulfate-reducing bacteria comprised 37% of the microbial community in the sulfidogenic region of the aquifer. Rapid mineralization of naphthalene and phenanthrene were observed in aerobic laboratory microcosms and resulted in significant enrichment of {beta}- and {gamma}-Proteobacteria potentially explaining their elevated presence in situ. Nitrate- and sulfate-limited mineralization of naphthalene in laboratory microcosms occurred to a small degree in aquifer sediments from locations where groundwater chemistry indicated nitrate- and sulfate-reduction, respectively. The results of this study suggest that FISH may be a useful tool for providing a link between laboratory microcosms and groundwater measurements made in situ necessary to better demonstrate the potential for natural attenuation at complex PAH contaminated sites.

Revisiting progesterone receptor (PR) actions in breast cancer: Insights into PR repressive functions.

Science.gov (United States)

Proietti, Cecilia J; Cenciarini, Mauro E; Elizalde, Patricia V

2018-05-01

Progesterone receptor (PR) is a master regulator in female reproductive tissues that controls developmental processes and proliferation and differentiation during the reproductive cycle and pregnancy. PR also plays a role in progression of endocrine-dependent breast cancer. As a member of the nuclear receptor family of ligand-dependent transcription factors, the main action of PR is to regulate networks of target gene expression in response to binding its cognate steroid hormone, progesterone. Liganded-PR transcriptional activation has been thoroughly studied and associated mechanisms have been described while progesterone-mediated repression has remained less explored. The present work summarizes recent advances in the understanding of how PR-mediated repression is accomplished in breast cancer cells and highlights the significance of fully understanding the determinants of context-dependent PR action. Copyright © 2018 Elsevier Inc. All rights reserved.

Microporous Organic Polymers Based on Hyper-Crosslinked Coal Tar: Preparation and Application for Gas Adsorption.

Science.gov (United States)

Gao, Hui; Ding, Lei; Bai, Hua; Li, Lei

2017-02-08

Hyper-crosslinked polymers (HCPs) are promising materials for gas capture and storage, but high cost and complicated preparation limit their practical application. In this paper, a new type of HCPs (CTHPs) was synthesized through a one-step mild Friedel-Crafts reaction with low-cost coal tar as the starting material. Chloroform was utilized as both solvent and crosslinker to generate a three-dimensional crosslinked network with abundant micropores. The maximum BET surface area of the prepared CTHPs could reach up to 929 m 2  g -1 . Owing to the high affinity between the heteroatoms on the coal-tar building blocks and the CO 2 molecules, the adsorption capacity of CTHPs towards CO 2 reached up to 14.2 wt % (1.0 bar, 273 K) with a high selectivity (CO 2 /N 2 =32.3). Furthermore, the obtained CTHPs could adsorb 1.27 wt % H 2 at 1.0 bar and 77.3 K, and also showed capacity for the capture of high organic vapors at room temperature. In comparison with other reported porous organic polymers, CTHPs have the advantages of low-cost, easy preparation, and high gas-adsorption performance, making them suitable for mass production and practical use in the future. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

75 FR 39241 - Hooper Springs Project

Science.gov (United States)

2010-07-08

... DEPARTMENT OF ENERGY Bonneville Power Administration Hooper Springs Project AGENCY: Bonneville... (collectively referred to as the Hooper Springs Project). The new BPA substation would be called Hooper Springs... proposed project would address voltage stability and reliability concerns of two of BPA's full requirements...

Environmental survey - tar sands in situ processing research program (Vernal, Uintah County, Utah). [Reverse-forward combustion; steam injection

Energy Technology Data Exchange (ETDEWEB)

Skinner, Q.

1980-03-01

Research will be done on the reverse-forward combustion and steam injection for the in-situ recovery of oil from tar sands. This environmental survey will serve as a guideline for the consideration of environmental consequences of such research. It covers the construction phase, operational phase, description of the environment, potential impacts and mitigations, coordination, and alternatives. (DLC)

Process for treating the dialyzed spent liquor from sulphonic acid containing sulfur minerals or tar oils or ammonium salts

Energy Technology Data Exchange (ETDEWEB)

Wernicke, E A

1936-08-09

Process for working up the dialyzate from sulfonic acid, sulfur-containing mineral or tar oils, or their ammonium salts, characterized by the combination of known steps, in the dialyzate being reacted with alkaline-earth oxide, hydroxide, or carbonate, and the resulting slightly soluble sulfate being filtered off and evaporated if necessary.

Preparation of thermo-sensitive slow releasing material and its application in low tar tobacco

Directory of Open Access Journals (Sweden)

Tian Zhong

2017-04-01

Full Text Available To solve some sensory defects such as fragrance deficiency,strong dry sense,poor satisfaction in the development of ultra-low tar tobacco products,we prepared a new thermo sensitive slow releasing composite material with tobacco aroma.The characterization results showed that the as-prepared thermosensitive particles have better aroma enhancing and slow releasing effects.Also,the aroma components of the tip stick containing thermosensitive particles were detected and its sensory quality was evaluated.The results showed that composite tip stick could enhance the aroma and improve the sensory quality of the cigarettes.

Phase diagram of Pr-P system

International Nuclear Information System (INIS)

Mironov, K.E.

1981-01-01

An area of the Pr-P system, adjoining to the Pr ordinate, is plotted up by the DTA method. Presence of P solid solution in Pr is established. Data on thermal stability of PrP, PrP 2 , PrP 5 and PrP 7 are generalized. The diagram of phase transformations in Pr-P system is plotted up proceeding from the whole complex of the data, presented. A supposition is made on a possible formation of solid solutions between the highest polyphosphide and phosphorus [ru

The Search for the Lost Cultural Identity——The Interpretation of Toni Morrison's Novel Tar Baby

Institute of Scientific and Technical Information of China (English)

郑艺

2011-01-01

Toni Morrison's novel Tar Baby is a novel with the theme on the search for cultural identity,from which it suggests Toni Morrison's attitude towards cultural identity and her answer to the search for the lost cultural identity.The paper is divided into three parts to reveal the African Americans' state of cultural marginalization,the importance of getting a balanced point between two different cultures and the way to search for cultural identity.

Cu4Pr6(MoO4)11-Pr2(MoO4)3 system

International Nuclear Information System (INIS)

Arzumanyan, G.A.

1982-01-01

Existence boundaries and Dalton compositions (CuPr(MoO 4 ) 2 , CuPr 3 (MoO 4 ) 5 ) of solid solutions that in the mojority are of shcheelite dsitored structure have been determined in the Cu 4 Pr 6 (MoO 4 ) 11 -Pr 2 (MoO 4 ) 3 system. It has been revealed that regions of homogeneity near the CuPr(MoO 4 ) 2 composition have a horseshoeshaped profile

Developing bulk exchange spring magnets

Science.gov (United States)

Mccall, Scott K.; Kuntz, Joshua D.

2017-06-27

A method of making a bulk exchange spring magnet by providing a magnetically soft material, providing a hard magnetic material, and producing a composite of said magnetically soft material and said hard magnetic material to make the bulk exchange spring magnet. The step of producing a composite of magnetically soft material and hard magnetic material is accomplished by electrophoretic deposition of the magnetically soft material and the hard magnetic material to make the bulk exchange spring magnet.

Optimal processing conditions for a dolomite cracker for cracking of tar from gasification of biomass fuels. Optimale procesbetingelser for en dolomitkrakker til krakning af tjaere fra forgasning af biobraendsler

Energy Technology Data Exchange (ETDEWEB)

Fjellerup, J.

1989-08-15

Gasification of fuels derived from biomass is of interest in connection with combined cycle systems. During gasification tar compounds can be produced, and these can block further stages of the process. As gas turbines are very sensitive to tar compounds it is necessary to remove the tar completely from the gas. The most effective method appears to be catalytic cracking and it is suggested that dolomite is an effective and cheap catalysator. Based on a survey of relevant literature, the aim was to discover optimal conditions for the process of dolomite cracking. It is concluded that it is important to decarbonate the dolomite before use, that dolomite is not suitable for use in fluidized beds as it can become eroded and is subsequently very quickly blown out, and that it is important to hold the temperature at a level of ca. 800 deg. C. Conditions for fixed bed cracking both with and without steam are also desderibed. (AB) 15 refs.

Vibro-spring particle size distribution analyser

International Nuclear Information System (INIS)

Patel, Ketan Shantilal

2002-01-01

This thesis describes the design and development of an automated pre-production particle size distribution analyser for particles in the 20 - 2000 μm size range. This work is follow up to the vibro-spring particle sizer reported by Shaeri. In its most basic form, the instrument comprises a horizontally held closed coil helical spring that is partly filled with the test powder and sinusoidally vibrated in the transverse direction. Particle size distribution data are obtained by stretching the spring to known lengths and measuring the mass of the powder discharged from the spring's coils. The size of the particles on the other hand is determined from the spring 'intercoil' distance. The instrument developed by Shaeri had limited use due to its inability to measure sample mass directly. For the device reported here, modifications are made to the original configurations to establish means of direct sample mass measurement. The feasibility of techniques for measuring the mass of powder retained within the spring are investigated in detail. Initially, the measurement of mass is executed in-situ from the vibration characteristics based on the spring's first harmonic resonant frequency. This method is often erratic and unreliable due to the particle-particle-spring wall interactions and the spring bending. An much more successful alternative is found from a more complicated arrangement in which the spring forms part of a stiff cantilever system pivoted along its main axis. Here, the sample mass is determined in the 'static mode' by monitoring the cantilever beam's deflection following the wanton termination of vibration. The system performance has been optimised through the variations of the mechanical design of the key components and the operating procedure as well as taking into account the effect of changes in the ambient temperature on the system's response. The thesis also describes the design and development of the ancillary mechanisms. These include the pneumatic

Force delivery of Ni-Ti coil springs.

Science.gov (United States)

Manhartsberger, C; Seidenbusch, W

1996-01-01

Sentalloy springs (GAC, Central Islip, N.Y.) of the open and closed type were investigated with a special designed device. The closed coil springs were subjected to a tensile and the open coil springs to a compression test. After a first measurement, the springs were activated for a period of 4 weeks and then reinvestigated with the same procedure. It could be shown distinctly that, with the different coil springs, the force delivery given by the producer could be achieved only within certain limits. To remain in the martensitic plateau, changed activation ranges, and for the Sentalloy coil springs white and red of the open and closed type, also changed force deliveries had to be taken into account. There was a distinct decrease in force delivery between the first and second measurement. After considering the loading curves of all the Sentalloy coil springs and choosing the right activation range respective to the force delivery, it was found that the coil springs deliver a superior clinical behavior and open new treatment possibilities.

Implementation of an ex situ stabilization technique at the Sand Springs superfund site to solidify and stabilize acid tar sludges involving a quick-lime based stabilization process and innovative equipment design

International Nuclear Information System (INIS)

McManus, R.W.; Grajczak, P.; Wilcoxson, J.C.; Webster, S.D.

1997-01-01

An old refinery site was safely remediated a year before schedule and for 25% less than final engineering estimates for the stabilization remedy thanks to energetic project management and innovative design involving ex situ stabilization/solidification of acid tar sludges. A quicklime based process, Dispersion by Chemical Reaction (DCR trademark), was employed to solidify and stabilize (SS) over 103,000 cubic meters (135,000 cubic yards) of petroleum waste, mostly acidic tarry sludge. The SS process was selected over competing methods because it afforded minimal volume increase, could readily achieve Record of Decision (ROD) specified physical and chemical treatment goals, could be implemented with treatment equipment that minimized emissions, and could be performed with low reagent usage and at low cost. To ensure treatment goals were achieved and an accelerated schedule met, a custom designed and fabricated transportable treatment unit (TTU) was employed to implement the process. The treated material was visually soil-like in character, it was left in stockpiles for periods of time, and it was placed and compacted in the on site landfill using standard earth-moving equipment

Flow-induced vibration of helical coil compression springs

International Nuclear Information System (INIS)

Stokes, F.E.; King, R.A.

1983-01-01

Helical coil compression springs are used in some nuclear fuel assembly designs to maintain holddown and to accommodate thermal expansion. In the reactor environment, the springs are exposed to flowing water, elevated temperatures and pressures, and irradiation. Flow parallel to the longitudinal axis of the spring may excite the spring coils and cause vibration. The purpose of this investigation was to determine the flow-induced vibration (FIV) response characteristics of the helical coil compression springs. Experimental tests indicate that a helical coil spring responds like a single circular cylinder in cross-flow. Two FIV excitation mechanisms control spring vibration. Namely: 1) Turbulent Buffeting causes small amplitude vibration which increases as a function of velocity squared. 2) Vortex Shedding causes large amplitude vibration when the spring natural frequency and Strouhal frequency coincide. Several methods can be used to reduce or to prevent vortex shedding large amplitude vibrations. One method is compressing the spring to a coil pitch-to-diameter ratio of 2 thereby suppressing the vibration amplitude. Another involves modifying the spring geometry to alter its stiffness and frequency characteristics. These changes result in separation of the natural and Strouhal frequencies. With an understanding of how springs respond in the flowing water environment, the spring physical parameters can be designed to avoid large amplitude vibration. (orig.)

Marble Canyon spring sampling investigation

International Nuclear Information System (INIS)

McCulley, B.

1985-10-01

The Mississippian Leadville Limestone is the most permeable formation in the lower hydrostratigraphic unit underlying the salt beds of the Paradox Formation in Gibson Dome, Paradox Basin, Utah, which is being considered as a potential nuclear waste repository site. The closest downgradient outcrop of the Mississippian limestone is along the Colorado River in Marble Canyon, Arizona. This report describes the sampling and interpretation of springs in that area to assess the relative contribution of Gibson Dome-type Leadville Limestone ground water to that spring discharge. The high-volume (hundreds of liters per second or thousands of gallons per minute) springs discharging from fault zones in Marble Canyon are mixtures of water recharged west of the Colorado River on the Kaibab Plateau and east of the river in the Kaiparowits basin. No component of Gibson Dome-type Leadville Limestone ground water is evident in major and trace element chemistry or isotopic composition of the Marble Canyon Springs. A low-volume (0.3 liters per second or 5 gallons per minute) spring with some chemical and isotopic characteristics of Gibson Dome-type Leadville Limestone water diluted by Kaiparowits basin-type water issues from a travertine mound in the Bright Angel Shale on the Little Colorado River. However, the stable isotopic composition and bromide levels of that spring discharge, in addition to probable ground-water flow paths, contradict the dilution hypothesis

Open-Coil Retraction Spring

Directory of Open Access Journals (Sweden)

Pavankumar Janardan Vibhute

2011-01-01

Full Text Available Sliding mechanic has become a popular method for space closure with developments in preadjusted edgewise appliance. Furthermore, various space closing auxiliaries have been developed and evaluated extensively for their clinical efficiency. Their effectiveness enhanced with optimum force magnitude and low-load deflection rate (LDR/force decay. With the advent of NiTi springs in orthodontics, LDRs have been markedly reduced. For use of NiTi, clinician has to depend upon prefabricated closed coil springs. “Open Coil Retraction Spring (OCRS” is developed utilizing NiTi open-coil spring for orthodontic space closure. This paper describes fabrication and clinical application of OCRS which have number of advantages. It sustains low LDR with optimum force magnitude. Its design is adjustable for desired length and force level. It is fail-safe for both activation and deactivation (i.e., it cannot be over activated, and decompression limit of open coil is also controlled by the operator, resp.. A possibility to offset the OCRS away from mucosa helps to reduce its soft-tissue impingement.

Porous carbon nanosheets from coal tar for high-performance supercapacitors

Science.gov (United States)

He, Xiaojun; Ma, Hao; Wang, Jingxian; Xie, Yuanyang; Xiao, Nan; Qiu, Jieshan

2017-07-01

A hydroxide-template strategy coupled with in-situ chemical activation is reported for the first time to fabricate porous carbon nanosheets (PCNSs) from coal tar. The thin PCNSs feature abundant short pores accessible for fast ion transport and high specific surface area up to 3235 m2 g-1 for ion adsorption. As electrodes for supercapacitors, the PCNSs show a high capacitance of 296.2 F g-1 at 0.05 A g-1 in 6 M KOH electrolyte, an excellent rate performance with a capacitance of 220.7 F g-1 at 20 A g-1 and a superior cycle stability with over 97.2% capacitance retention after 11000 charge-discharge cycles at 3.5 A g-1. This work paves a new way for efficient fabrication of sheet-like carbon materials with tuned porous structure from polycyclic aromatic hydrocarbons for high performance supercapacitors.

First experimental results on the IShTAR testbed

Energy Technology Data Exchange (ETDEWEB)

D’Inca, R.; Jacquot, J.; Ochoukov, R.; Morgal, I.; Fünfgelder, H.; Faugel, H. [Max-Planck-Institut für Plasmaphysik, Garching (Germany); Crombe, K.; Louche, F.; Van Eester, D. [LPP-ERM-KMS, TEC partner, Brussels (Belgium); Heuraux, S.; Devaux, S.; Moritz, J.; Faudot, E. [Institut Jean Lamour UMR 7198 CNRS-Université de Lorraine, Nancy (France); Noterdaeme, J.-M. [Max-Planck-Institut für Plasmaphysik, Garching (Germany); Department of Applied Physics, Ghent University (Belgium)

2015-12-10

IShTAR (Ion cyclotron Sheath Test ARrangement) is a linear magnetized plasma test facility dedicated to the investigation of RF wave/plasma interaction [1] in the Ion Cyclotron Range of Frequencies (ICRF). It provides a better accessibility for the instrumentation than tokamaks while being representative of the neighboring region of the wave emitter. It is equipped with a magnetized plasma source (1 m long, 0.4 m diameter) powered by a helical antenna up to 3 kW at 11 MHz. We present the results of the first analysis of the plasma characteristics (plasma density, electron temperature) in function of the operating parameters (injected power, neutral pressure and magnetic field) as measured with fixed and movable Langmuir probes, spectrometer and cameras. The plasma is presently produced only by the helical antenna (no ICRF). We show that the plasma exists in three regime depending on the power level: the first two ones are stable and separated by a jump in density; a first spatial profile of the plasma density has been established for these modes; The third mode is unstable, characterized by strong oscillations of the plasma tube position.

Photon cascade luminescence from Pr3+ ions in LiPrP4O12 polyphosphate

International Nuclear Information System (INIS)

Shalapska, T; Stryganyuk, G; Romanyshyn, Yu; Demchenko, P; Voloshinovskii, A; Trots, D; Gektin, A; Dorenbos, P

2010-01-01

The spectral-kinetic properties of luminescence from LiY 1-x Pr x P 4 O 12 (x = 1, 0.1) phosphors are studied in the 10-300 K temperature range upon excitation within the UV-VUV spectral range. The luminescence observed for LiPrP 4 O 12 at low temperatures is attributed to both intra-configurational 4f 2 → 4f 2 and inter-configurational 4f5d → 4f 2 radiative transitions of Pr 3+ . The temperature dependence of emission and the decay kinetics of Pr 3+ luminescence from LiY 1-x Pr x P 4 O 12 (x = 1, 0.1) phosphors are explained by temperature stimulated transitions from the 1 S 0 to the Pr 3+ 4f5d state. At low temperatures, the energy potential barrier between the 1 S 0 and 4f5d states is 0.014 eV for LiPrP 4 O 12 . The spectral overlap of the 1 S 0 and 4f5d states of Pr 3+ in LiY 0.9 Pr 0.1 P 4 O 12 determines the luminescence properties in the entire temperature range studied.

Outer grid strap protruding spring repair apparatus

International Nuclear Information System (INIS)

Widener, W.H.

1987-01-01

This patent describes a nuclear fuel assembly grid spring repair apparatus for repairing a spring formed on an outer strap of a fuel assembly grid and having a portion protruding outwardly beyond the strap, the apparatus comprising: (a) a support frame defining an opening and having means defining a guide channel extending along the opening in a first direction; (b) means mounted on the frame and being adjustable for attaching the frame to the outer strap of the support grid so that the frame opening is aligned with the outwardly protruding spring on the outer strap; (c) an outer slide having a passageway defined therethrough and being mounted in the guide channel for reciprocable movement along the frame opening in the first direction for aligning the passageway with the outwardly protruding portion of the spring on the outer strap. The outer slide also has means defining a guide way extending along the passageway in a second direction generally orthogonal to the first direction; (d) a spring reset mechanism being operable for resetting the protruding spring to a nonprotruding position relative to the outer strap when the mechanism is aligned with the protruding portion of the spring; and (e) an inner slide supporting the spring reset mechanism and being mounted to the guide way for reciprocable movement along the passageway of the outer slide in the second direction for aligning the spring reset mechanism with the protruding portion of the spring on the outer strap

Shoreline erosion and decadal sediment accumulation in the Tar-Pamlico estuary, North Carolina, USA: A source-to-sink analysis

Science.gov (United States)

Eulie, Devon O.; Corbett, D. Reide; Walsh, J. P.

2018-03-01

Estuaries contain vital habitats and it is important to understand how these areas respond to human activities and natural processes such as sea-level rise and wave attack. As estuarine shorelines erode or become modified with hard structures, there is potential for significantly altering the availability of sediment and the filling of coastal systems. This study used a source-to-sink approach and quantified rates of shoreline erosion in the Tar-Pamlico sub-estuary, a tributary of the larger Albemarle-Pamlico Estuarine System (APES). The average shoreline change rate (SCR) determined using an end-point method was -0.5 ± 0.9 m yr-1 for the Tar-Pamlico. Incorporating bulk density estimates, this contributes 0.6 × 105 tons of fine sediment to the system annually, or after accounting for fluvial input, about 40% of the total sediment supply to the sub-estuary. The role of the Tar-Pamlico as a sink for these sediments was addressed using the radionuclide tracers 210Pb and 137Cs. Radionuclide activities and sediment accumulation rates identified several depositional regions, in particular in the middle of the estuary. Linear sediment accumulation rates ranged from 0.10 ± 0.02 to 0.38 ± 0.02 g cm-2 yr-1, and total storage of fine sediment in the system was 1.6 × 105 t yr-1. It was not possible to confidently discern a change in the rate of shoreline erosion or seabed accumulation. A preliminary budget for fine sediments (grain-size <63 μm) was then calculated to compare erosional sources with sedimentary sinks. Almost all (∼93.0%) of the fine sediment entering the system was accumulated and stored, while only about 7.0% was exported to Pamlico Sound.

Prediction of Spring Rate and Initial Failure Load due to Material Properties of Composite Leaf Spring

International Nuclear Information System (INIS)

Oh, Sung Ha; Choi, Bok Lok

2014-01-01

This paper presented analysis methods for adapting E-glass fiber/epoxy composite (GFRP) materials to an automotive leaf spring. It focused on the static behaviors of the leaf spring due to the material composition and its fiber orientation. The material properties of the GFRP composite were directly measured based on the ASTM standard test. A reverse implementation was performed to obtain the complete set of in-situ fiber and matrix properties from the ply test results. Next, the spring rates of the composite leaf spring were examined according to the variation of material parameters such as the fiber angles and resin contents of the composite material. Finally, progressive failure analysis was conducted to identify the initial failure load by means of an elastic stress analysis and specific damage criteria. As a result, it was found that damage first occurred along the edge of the leaf spring owing to the shear stresses

Oro taršos lakiaisiais organiniais junginiais tyrimas ir jos mažinimas naftos terminaluose

OpenAIRE

Paulauskienė, Tatjana

2008-01-01

Disertacijoje nagrinėjama naftos ir jos produktų garavimo terminaluose problema. Pagrindinis disertacijos tikslas – įvertinti atmosferos taršą lakiaisiais organiniais junginiais (LOJ) naftos terminaluose, nustatyti meteorologinių elementų ir krovos indikatoriaus įtaką LOJ koncentracijos kitimui pažemės atmosferos sluoksnyje. Darbe sprendžiami keli pagrindiniai uždaviniai: ištirti LOJ pasiskirstymą pažemės atmosferos sluoksnyje už naftos terminalų teritorijos skirtingais metų sezonais atsižvel...

Pro Spring security

CERN Document Server

Scarioni, Carlo

2013-01-01

Security is a key element in the development of any non-trivial application. The Spring Security Framework provides a comprehensive set of functionalities to implement industry-standard authentication and authorization mechanisms for Java applications. Pro Spring Security will be a reference and advanced tutorial that will do the following: Guides you through the implementation of the security features for a Java web application by presenting consistent examples built from the ground-up. Demonstrates the different authentication and authorization methods to secure enterprise-level applications

Nuclear graphite based on coal tar pitch; behavior under neutron irradiation between 400 and 14000C

International Nuclear Information System (INIS)

Mottet, P.; Fillatre, A.; Schill, R.; Micaud, G.

1977-01-01

Two nuclear grades of coal tar pitch coke graphites have been developed and tested under neutron irradiation. The neutron irradiation induced dimensional changes between 400 and 1400 0 C, at fluences up to 1,2.10 22 n.cm -2 PHI.FG show a behavior comparable to anisotropic petroleum coke graphites. Less than 10% variation in thermal expansion, maximum decrease by a factor four in thermal conductivity, and large increase of the Young modulus have been observed

1988 Hanford riverbank springs characterization report

International Nuclear Information System (INIS)

Dirkes, R.L.

1990-12-01

This reports presents the results of a special study undertaken to characterize the riverbank springs (i.e., ground-water seepage) entering the Columbia River along the Hanford Site. Radiological and nonradiological analyses were performed. River water samples were also analyzed from upstream and downstream of the Site as well as from the immediate vicinity of the springs. In addition, irrigation return water and spring water entering the river along the shoreline opposite Hanford were analyzed. Hanford-origin contaminants were detected in spring water entering the Columbia River along the Hanford Site. The type and concentrations of contaminants in the spring water were similar to those known to exist in the ground water near the river. The location and extent of the contaminated discharges compared favorably with recent ground-water reports and predictions. Spring discharge volumes remain very small relative to the flow of the Columbia. Downstream river sampling demonstrates the impact of ground-water discharges to be minimal, and negligible in most cases. Radionuclide concentrations were below US Department of Energy Derived Concentration Guides (DCGs) with the exception 90 Sr near the 100-N Area. Tritium, while below the DCG, was detected at concentrations above the US Environmental Protection Agency drinking water standards in several springs. All other radionuclide concentrations were below drinking water standards. Nonradiological contaminants were generally undetectable in the spring water. River water contaminant concentrations, outside of the immediate discharge zones, were below drinking water standards in all cases. 19 refs., 5 figs., 12 tabs

A springs actuated finger exoskeleton: From mechanical design to spring variables evaluation.

Science.gov (United States)

Bortoletto, Roberto; Mello, Ashley N; Piovesan, Davide

2017-07-01

In the context of post-stroke patients, suffering of hemiparesis of the hand, robot-aided neuro-motor rehabilitation allows for intensive rehabilitation treatments and quantitative evaluation of patients' progresses. This work presents the design and evaluation of a spring actuated finger exoskeleton. In particular, the spring variables and the interaction forces between the assembly and the hand were investigated, in order to assess the effectiveness of the proposed exoskeleton.

Portrait of a Geothermal Spring, Hunter's Hot Springs, Oregon.

Science.gov (United States)

Castenholz, Richard W

2015-01-27

Although alkaline Hunter's Hot Springs in southeastern Oregon has been studied extensively for over 40 years, most of these studies and the subsequent publications were before the advent of molecular methods. However, there are many field observations and laboratory experiments that reveal the major aspects of the phototrophic species composition within various physical and chemical gradients of these springs. Relatively constant temperature boundaries demark the upper boundary of the unicellular cyanobacterium, Synechococcus at 73-74 °C (the world-wide upper limit for photosynthesis), and 68-70 °C the upper limit for Chloroflexus. The upper limit for the cover of the filamentous cyanobacterium, Geitlerinema (Oscillatoria) is at 54-55 °C, and the in situ lower limit at 47-48 °C for all three of these phototrophs due to the upper temperature limit for the grazing ostracod, Thermopsis. The in situ upper limit for the cyanobacteria Pleurocapsa and Calothrix is at ~47-48 °C, which are more grazer-resistant and grazer dependent. All of these demarcations are easily visible in the field. In addition, there is a biosulfide production in some sections of the springs that have a large impact on the microbiology. Most of the temperature and chemical limits have been explained by field and laboratory experiments.

Soft tissue modelling with conical springs.

Science.gov (United States)

Omar, Nadzeri; Zhong, Yongmin; Jazar, Reza N; Subic, Aleksandar; Smith, Julian; Shirinzadeh, Bijan

2015-01-01

This paper presents a new method for real-time modelling soft tissue deformation. It improves the traditional mass-spring model with conical springs to deal with nonlinear mechanical behaviours of soft tissues. A conical spring model is developed to predict soft tissue deformation with reference to deformation patterns. The model parameters are formulated according to tissue deformation patterns and the nonlinear behaviours of soft tissues are modelled with the stiffness variation of conical spring. Experimental results show that the proposed method can describe different tissue deformation patterns using one single equation and also exhibit the typical mechanical behaviours of soft tissues.

Isolators Including Main Spring Linear Guide Systems

Science.gov (United States)

Goold, Ryan (Inventor); Buchele, Paul (Inventor); Hindle, Timothy (Inventor); Ruebsamen, Dale Thomas (Inventor)

2017-01-01

Embodiments of isolators, such as three parameter isolators, including a main spring linear guide system are provided. In one embodiment, the isolator includes first and second opposing end portions, a main spring mechanically coupled between the first and second end portions, and a linear guide system extending from the first end portion, across the main spring, and toward the second end portion. The linear guide system expands and contracts in conjunction with deflection of the main spring along the working axis, while restricting displacement and rotation of the main spring along first and second axes orthogonal to the working axis.

Evaluation of natural attenuation processes in the groundwater of a tar oil contaminated site: development of a monitoring network

International Nuclear Information System (INIS)

Borke, P.; Husers, N.; Werner, P.; Leibenath, C.

2005-01-01

Tar oil is a complex mixture of mainly aromatic hydrocarbons. It is found in the subsurface of manufactured gas plants (MGP), coking plants or wood preserving facilities. The transportation into the soil and groundwater stands for a severe contamination. This is due to the physico-chemical properties of the DNAPL (dense non aqueous phase liquid) and its mobility in the soil and aquifer system. Additionally most of the contaminants show a low biological degradability and solubility under in situ conditions. Therefore it is known as a long term source of contamination. Nevertheless, natural attenuation (NA) processes are detectable at tar oil contaminated sites. In the thematic network two of the German funding priority KORA (http://www.natural-attenuation.de) these processes are matter of investigation. Four typical contaminated sites were chosen to evaluate under which circumstances monitored natural attenuation (MNA) is applicable. Furthermore enhanced natural attenuation questions are examined. The design of monitoring networks at tar oil contaminated sites plays a significant role in gaining field evidence for natural attenuation as well as documenting the efficiency of the attenuation processes and evaluating the matching of performance goals. Well designed monitoring networks include the placement of monitoring wells in 3D so that 3D flow path, mass balances and an estimation of mass flux can be monitored. As an example the history of the monitoring network of a wood preserving facility is shown. Starting from a risk assessment network to a network for MNA is presented. In this case for example especially the determination of the groundwater flow direction in time and space is connected to the number of observation wells and their location. Moreover in the beginning the observation wells were located according to the assumed centerline of the plume. Because of the variability of the groundwater flow direction and the need to determine mass flux a control plane

PrEP (Pre-Exposure Prophylaxis) 101

Science.gov (United States)

... than 70%. Your risk of getting HIV from sex can be even lower if you combine PrEP with condoms and other prevention methods. Download PrEP 101 Consumer Info Sheet Vital Signs Fact Sheet on Daily Pill Can Prevent HIV (PrEP) Expand All Collapse All Video Introductions to PrEP What is PrEP? A Brief ...

PrP Conformational Transitions Alter Species Preference of a PrP-specific antibody

NARCIS (Netherlands)

Zou, W.Q.; Langeveld, J.P.M.; Xiao, X.; Chen, S.; McGeer, P.L.; Yuan, J.; Payne, M.C.; Kang, H.E.; McGeehan, J.M.; Sy, M.S.; Greenspan, N.S.; Kaplan, D.; Wang, G.X.; Parchi, P.; Hoover, E.A.; Kneale, G.; Telling, G.; Surewicz, W.; Kong, Q.; Guo, J.

2010-01-01

The epitope of the 3F4 antibody most commonly used in human prion disease diagnosis is believed to consist of residues Met-Lys-His-Met (MKHM) corresponding to human PrP-(109–112). This assumption is based mainly on the observation that 3F4 reacts with human and hamster PrP but not with PrP from

Algunos aspectos ecológicos de “tarántulas” (Araneae: Theraphosidae en dos tipos de bosques en San Juan Bautista, Loreto, Perú

Directory of Open Access Journals (Sweden)

Pablo Reátegui Suárez

2014-12-01

Full Text Available Los resultados muestran la presencia de tarántulas del área de concesión de la empresa Perufish Aquarium EIRL, quebrada Yanayacu, río Itaya, Loreto. Reportándose un total de 5 especies de la familia Theraphosidae. Las 5 especies estuvieron en los bosques de colinas bajas moderadamente disectadas y 3 de estas en el bosque de colinas bajas ligeramente disectadas. Las especies más abundantes fueron Megaphobema velvetosoma con 64.3% y Cyriocosmus sellatus con 35%. El tamaño promedio de la abertura de las madrigueras varió en relación al tamaño de las especies, la más grande correspondió a Megaphobema velvetosoma con un promedio de 66,6 mm, y la más pequeña a Acanthoscurria ferina con un promedio de 21 mm. La temperatura del interior de las madrigueras varió de 25,2°C a 25,7°C y la humedad relativa de 88% a 88,7%. Las madrigueras se encontraron en el suelo con una capa de hojarasca que varió de 2,7 a 4,9 cm. Las especies de tarántulas se distribuyeron formando grupos en las zonas evaluadas. Las muestras de tarántulas se encuentran depositadas en la Universidad Nacional de la Amazonia Peruana y en la empresa Perufish Aquarium EIRL.

Masters of the springs

DEFF Research Database (Denmark)

Laursen, Steffen

2010-01-01

flanked by villages that relied on these water recourses for agricultural production. The springs emerged in the zone separating the cemeteries from the settlements. The freshwater springs were actively incorporated into the religious landscape of the dead, by consistently erecting mounds of a particular...... for water - a process which perhaps also is evidenced by temple constructions at Barbar, Umm al-Sujur and Abu Zaydan....

Optical spring effect in nanoelectromechanical systems

International Nuclear Information System (INIS)

Tian, Feng; Zhou, Guangya; Du, Yu; Chau, Fook Siong; Deng, Jie

2014-01-01

In this Letter, we report a hybrid system consisting of nano-optical and nano-mechanical springs, in which the optical spring effect works to adjust the mechanical frequency of a nanoelectromechanical systems resonator. Nano-scale folded beams are fabricated as the mechanical springs and double-coupled one-dimensional photonic crystal cavities are used to pump the “optical spring.” The dynamic characteristics of this hybrid system are measured and analyzed at both low and high input optical powers. This study leads the physical phenomenon of optomechanics in complex nano-opto-electro-mechanical systems (NOEMS) and could benefit the future applications of NOEMS in chip-level communication and sensing

PrP expression, PrPSc accumulation and innervation of splenic compartments in sheep experimentally infected with scrapie.

Directory of Open Access Journals (Sweden)

Randi Sørby

Full Text Available BACKGROUND: In prion disease, the peripheral expression of PrP(C is necessary for the transfer of infectivity to the central nervous system. The spleen is involved in neuroinvasion and neural dissemination in prion diseases but the nature of this involvement is not known. The present study undertook the investigation of the spatial relationship between sites of PrP(Sc accumulation, localisation of nerve fibres and PrP(C expression in the tissue compartments of the spleen of scrapie-inoculated and control sheep. METHODOLOGY/PRINCIPAL FINDINGS: Laser microdissection and quantitative PCR were used to determine PrP mRNA levels and results were compared with immunohistochemical protocols to distinguish PrP(C and PrP(Sc in tissue compartments of the spleen. In sheep experimentally infected with scrapie, the major sites of accumulation of PrP(Sc in the spleen, namely the lymphoid nodules and the marginal zone, expressed low levels of PrP mRNA. Double immunohistochemical labelling for PrP(Sc and the pan-nerve fibre marker, PGP, was used to evaluate the density of innervation of splenic tissue compartments and the intimacy of association between PrP(Sc and nerves. Some nerve fibres were observed to accompany blood vessels into the PrP(Sc-laden germinal centres. However, the close association between nerves and PrP(Sc was most apparent in the marginal zone. Other sites of close association were adjacent to the wall of the central artery of PALS and the outer rim of germinal centres. CONCLUSIONS/SIGNIFICANCE: The findings suggest that the degree of PrP(Sc accumulation does not depend on the expression level of PrP(C. Though several splenic compartments may contribute to neuroinvasion, the marginal zone may play a central role in being the compartment with most apparent association between nerves and PrP(Sc.

ESO PR Highlights in 2006

Science.gov (United States)

2007-01-01

Last year proved to be another exceptional year for the European organisation for ground-based astronomy. ESO should begin the New Year with two new member states: Spain (PR 05/06) and the Czech Republic (PR 52/06). ESO PR Highlights 2006 2006 was a year of renovation and revolution in the world of planets. A new Earth-like exoplanet has been discovered (PR 03/06) using a network of telescopes from all over the world (including the Danish 1.54-m one at ESO La Silla). It is not the only child of this fruitful year: thanks to the combined use of ESO's Very Large Telescope (VLT) and La Silla instruments, a surprising system of twin giant exoplanets was found (PR 29/06), and a trio of Neptune-like planets hosted by a nearby star were identified (PR 18/06). These results open new perspectives on the search for habitable zones and on the understanding of the mechanism of planet formation. The VISIR instrument on the VLT has been providing unique information to answer this last question, by supplying a high resolution view of a planet-forming disc (PR 36/06). There are not only new members in the planets' register: during the General Assembly of the International Astronomical Union held in Prague (Czech Republic), it was decided that Pluto is not a planet anymore but a 'dwarf planet'. Whatever its status, Pluto still has a satellite, Charon, whose radius and density have been measured more accurately by observing a rare occultation from different sites, including Cerro Paranal (PR 02/06). The scientific community dedicated 2006 to the great physicist James Clerk Maxwell (it was the 175th anniversary of the birth): without his electromagnetic theory of light, none of the astonishing discoveries of modern physics could have been achieved. Nowadays we can look at distant galaxies in great detail: the GIRAFFE spectrograph on the VLT revealed that galaxies 6 billion years ago had the same amount of dark matter relative to stars than nowadays (PR 10/06), while SINFONI gave an

Cancer de la próstata

OpenAIRE

Mendoza, Lupi Alejandro; Fundación Valle de Lili; Gutierrez, María Carolina; López Cardona, Arturo

1997-01-01

¿Qué es la próstata?/¿Qué es la hiperplasia benigna de próstata?/El cáncer de próstata/¿Se hereda el cáncer de próstata?/¿Cómo se presenta y hacia donde se disemina el cáncer de próstata?/¿Cómo de descubre el cáncer de próstata?/¿Qué estudia la ultrasonografía transrectal o ecografía a través de recto?/¿Cómo se analizan los niveles de PSA?/¿Cómo se clasifica el cáncer de próstata?¿Cómo se determina la terapia más adecuada para un cáncer de próstata?/¿Cuáles son las opciones de tratamiento par...

Fossilization Processes in Thermal Springs

Science.gov (United States)

Farmer, Jack D.; Cady, Sherry; Desmarais, David J.; Chang, Sherwood (Technical Monitor)

1995-01-01

To create a comparative framework for the study of ancient examples, we have been carrying out parallel studies of the microbial biosedimentology, taphonomy and geochemistry of modem and sub-Recent thermal spring deposits. One goal of the research is the development of integrated litho- and taphofacies models for siliceous and travertline sinters. Thermal springs are regarded as important environments for the origin and early evolution of life on Earth, and we seek to utilize information from the fossil record to reconstruct the evolution of high temperature ecosystems. Microbial contributions to the fabric of thermal spring sinters occur when population growth rates keep pace with, or exceed rates of inorganic precipitation, allowing for the development of continuous biofilms or mats. In siliceous thermal springs, microorganisms are typically entombed while viable. Modes of preservation reflect the balance between rates of organic matter degradation, silica precipitation and secondary infilling. Subaerial sinters are initially quite porous and permeable and at temperatures higher than about 20 C, organic materials are usually degraded prior to secondary infilling of sinter frameworks. Thus, organically-preserved microfossils are rare and fossil information consists of characteristic biofabrics formed by the encrustation and underplating of microbial mat surfaces. This probably accounts for the typically low total organic carbon values observed in thermal spring deposits. In mid-temperature, (approx. 35 - 59 C) ponds and outflows, the surface morphology of tufted Phormidium mats is preserved through mat underplating by thin siliceous: crusts. Microbial taxes lead to clumping of ceils and/or preferred filament orientations that together define higher order composite fabrics in thermal spring stromatolites (e.g. network, coniform, and palisade). At lower temperatures (less than 35 C), Calothrix mats cover shallow terracette pools forming flat carpets or pustular

European supply chain for valve springs

Energy Technology Data Exchange (ETDEWEB)

Barthold, G. [Scherdel GmbH, Marktredwitz (Germany); Thureborn, D.; Hallberg, M. [Haldex Garphyttan AB (Sweden); Janssen, P. [Mittal Steel Ruhrort GmbH / Mittal Steel Hochfeld GmbH (Germany)

2005-07-01

Forced by the Kobe earthquake in 1995 and the lack of valve spring steel on the world market due to damages of the Kobe steel plant, the development of a European supply chain has been sped up. End of 1994 a super clean valve spring steel with a reasonable quality from a European source was available. A strong relationship between the steel producer (Mittal), the wire manufacturer (Haldex Garphyttan) and the spring maker (Scherdel) was established. A working group of the three companies holds meetings on a regular basis to discuss quality and development issues. Over the last years the supply chain has achieved significant improvements in terms of cleanliness and decarburisation of the wire rod. The continuous common advancement of the valve spring quality has enabled the valve spring failures in the field to be reduced to < 0.1 ppm. The development and market launch of new grades has been prepared. (orig.)

Characteristics Analysis and Testing of SMA Spring Actuator

Directory of Open Access Journals (Sweden)

Jianzuo Ma

2013-01-01

Full Text Available The biasing form two-way shape memory alloy (SMA actuator composed of SMA spring and steel spring is analyzed. Based on the force equilibrium equation, the relationship between load capacity of SMA spring and geometric parameters is established. In order to obtain the characteristics of SMA spring actuator, the output force and output displacement of SMA spring under different temperatures are analyzed by the theoretical model and the experimental method. Based on the shape memory effect of SMA, the relationship of the SMA spring actuator's output displacement with the temperature, the stress and strain, the material parameters, and the size parameters is established. The results indicate that the trend of theoretical results is basically consistent with the experimental data. The output displacement of SMA spring actuator is increased with the increasing temperature.

Controllable growth of nanostructured carbon from coal tar pitch by chemical vapor deposition

International Nuclear Information System (INIS)

Liu Xuguang; Yang Yongzhen; Ji Weiyun; Liu Hongyan; Zhang Chunyi; Xu Bingshe

2007-01-01

The direct synthesis of vapor grown carbon fibers with different diameters was achieved by the pyrolysis of coal tar pitch by chemical vapor deposition. The products were characterized by field-emission scanning electron microscopy, high resolution transmission electron microscopy, X-ray diffraction and Raman spectroscopy. The experimental results demonstrated that ferrocene content, reaction temperature and Ar flow rate strongly influenced the yield and nature of nanostructured carbon materials, pure carbon microbeads, with diameter distribution ranging from 450 to 650 nm, were also obtained in the absence of catalyst, uniform and straight carbon nanofibers with the outer diameter of about 115 nm were obtained and curl and thick carbon fibers with narrow diameter distribution of 300-350 nm were produced

Thermal algae in certain radioactive springs in Japan, (3)

International Nuclear Information System (INIS)

Mifune, Masaaki; Hirose, Hiroyuki.

1982-01-01

Shikano Hot Springs are located at five km to the south of Hamamura Station on the Sanin Line in Tottori Prefecture. The water temperature and the pH of the springs are 40.2 - 61.2 0 C, and 7.5 - 7.8, respectively. They belong to simple thermals. Hamamura Hot Springs are located in the neighbourhood of Hamamura Station. The highest radon content of the hot springs is 175.1 x 10 -10 Ci/l, and the great part of the springs belong to radioactive ones. From the viewpoint of the major ionic constituents, they are also classified under weak salt springs, sulfated salt springs, and simple thermals. Regarding the habitates of the algal flora, the water temperature and the pH of the springs are 28.0 - 68.0 0 C, and 6.8 - 7.4, respectively. The thermal algae found by Ikoma and Doi at Hamamura Hot Springs were two species of Cyanophyceae. By the authors, nine species and one variety of Cyanophyceae including Ikoma and Doi's two species were newly found at Shikano and Hamamura Hot Springs. Chlorophyceous alga was not found. The dominant thermal algae of these hot springs were Mastigocladus laminosus, and the other algae which mainly consist of Oscillatoriaceous algae. From these points, it seems that the thermal algae of Shikano and Hamamura Hot Springs belong to the normal type of thermal algae, and they are different from the thermal algae of Ikeda Mineral Springs and Masutomi Hot Springs which belong to strongly radioactive springs. (author)

Thermal springs of Malaysia and their potentialdevelopment

Science.gov (United States)

Rahim Samsudin, Abdul; Hamzah, Umar; Rahman, Rakmi Ab.; Siwar, Chamhuri; Fauzi Mohd. Jani, Mohd; Othman, Redzuan

The study on the potential development of hot springs for the tourism industry in Malaysiawas conducted. Out of the 40 hot springs covered, the study identified 9 hot springs having a high potential for development, 14 having medium potential and the remaining 17 having low or least potential for development. This conclusion was arrived at after considering the technical and economic feasibility of the various hot springs. Technical feasibility criteria includes geological factors, water quality, temperature and flow rate. The economic feasibility criteria considers measures such as accessibility, current and market potentials in terms of visitors, surrounding attractions and existing inventory and facilities available. A geological input indicates that high potential hot springs are located close to or within the granite body and associated with major permeable fault zones. They normally occur at low elevation adjacent to topographic highs. High potential hot springs are also characterised by high water temperature, substantial flowrate and very good water quality which is important for water-body contact activities such as soaking. Economic criteria for high potential hot springs are associated with good accessibility, good market, good surrounding attractions like rural and village setting and well developed facilities and infrastructures.

Spring harvest of corn stover

Energy Technology Data Exchange (ETDEWEB)

Lizotte, P.L. [Laval Univ., Quebec City, PQ (Canada). Dept. des sols et de genie agroalimentaire; Savoie, P. [Agriculture and Agri-Food Canada, Quebec City, PQ (Canada)

2010-07-01

Corn stover is typically left behind in the field after grain harvest. Although part of the stover should remain in the field for soil organic matter renewal and erosion protection, half of the stover could be removed sustainably. This represents about one million t dry matter (DM) of stover per year in the province of Quebec. Stover harvested in the fall is very wet. While there are applications for wet stover, the available markets currently require a dry product. Preliminary measurements have shown that stover left in the field throughout the winter becomes very dry, and a considerable amount would still be harvestable in the spring. In the spring of 2009, corn stover was harvested at 2 sites, each subdivided into 2 parcels. The first parcel was cut and raked in the fall of 2008 (fall parcel), while the second parcel was cut and raked in spring 2009. Fibre from both parcels was baled in the spring 2009. At the first site, a large square baler was used in late April to produce bales measuring 0.8 m x 0.9 m x 1.8 m. On the second site a round baler was used in late May to produce bales of 1.2 m in width by 1.45 m in diameter. On the second site, a small square baler was also used to produce bales of 0.35 m x 0.45 m x 0.60 m (spring cutting only). With the large square baler, an average of 3.9 t DM/ha was harvested equally on the fall parcel and the spring parcel, representing a 48 per cent recovery of biomass based on stover yields.

Production of no-carrier-added 139Pr via precursor decay in the proton bombardment of natPr

International Nuclear Information System (INIS)

Steyn, G.F.; Vermeulen, C.; Nortier, F.M.; Szelecsenyi, F.; Kovacs, Z.; Qaim, S.M.

2006-01-01

Excitation functions and production rates are presented for various Pr and Nd radionuclides formed in the bombardment of Pr with protons, from their respective thresholds up to 100 MeV. The indirect production route 141 Pr(p, 3n) 139m Nd → 139 Pr is investigated as an alternative to the direct production route 140 Ce(p, 2n) 139 Pr for producing no-carrier-added 139 Pr of high radionuclidic purity. The simultaneous production of 139 Pr and 140 Nd using Pr as target is investigated. The advantages and disadvantages of both production routes are discussed. Experimental thick-target production rates are presented for selected Pr radionuclides formed in the bombardment of nat Ce with protons at incident energies of 20, 26 and 32 MeV. All the experimental excitation functions obtained in this work are compared with theoretical predictions by means of the geometry-dependent hybrid (GDH) model as implemented in the code ALICE-IPPE. The results of this work are also compared with previous literature experimental data, if available

Erfolgsfaktoren unternehmerischer Krisen-PR

OpenAIRE

Scharr, Florian

2006-01-01

Ob "Peanuts", "Elchtest" oder "Hoechst-Störfall" - bei diesen bekannten Öffentlichkeitskrisen der letzten Jahre rief die mangelhafte Krisen-PR der betroffenen Unternehmen bei Medien und Bevölkerung mehr Empörung hervor als die originären Auslöser und potenzierte so den entstandenen Vertrauensverlust. Auch die sich gerade erst entwickelnde PR-Forschung bietet noch keine konkrete Hilfestellung zur Gestaltung von Krisen-PR. Mit dem bedeutenden Diskurs- und dadurch Realitätsgestaltungsmittel Pres...

The Begg's uprighting spring - Revisited.

Science.gov (United States)

Kumar, Vinay; Sundareswaran, Shobha

2015-01-01

Uprighting springs, an integral part of the Begg ligsht wire differential force technique is gaining more and more popularity, as a useful adjunct in contemporary preadjusted edgewise appliance systems as well. It can be used with brackets containing vertical slots for mesiodistal crown uprighting, or as braking auxiliaries providing additional anchorage while protracting posteriors. Here, we present a simple and quick chair side method of fabricating and customizing uprighting springs according to the required crown/root movement for correction. This communication would serve as a ready reckoner during fabrication of the springs, thus dispelling the confusion that usually arises regarding direction and position of the coil and active arm.

Hydrogen-Rich Gas Production by Sorption Enhanced Steam Reforming of Woodgas Containing TAR over a Commercial Ni Catalyst and Calcined Dolomite as CO2 Sorbent

Directory of Open Access Journals (Sweden)

Vincenzo Naso

2013-07-01

Full Text Available The aim of this work was the evaluation of the catalytic steam reforming of a gaseous fuel obtained by steam biomass gasification to convert topping atmosphere residue (TAR and CH4 and to produce pure H2 by means of a CO2 sorbent. This experimental work deals with the demonstration of the practical feasibility of such concepts, using a real woodgas obtained from fluidized bed steam gasification of hazelnut shells. This study evaluates the use of a commercial Ni catalyst and calcined dolomite (CaO/MgO. The bed material simultaneously acts as reforming catalyst and CO2 sorbent. The experimental investigations have been carried out in a fixed bed micro-reactor rig using a slipstream from the gasifier to evaluate gas cleaning and upgrading options. The reforming/sorption tests were carried out at 650 °C while regeneration of the sorbent was carried out at 850 °C in a nitrogen environment. Both combinations of catalyst and sorbent are very effective in TAR and CH4 removal, with conversions near 100%, while the simultaneous CO2 sorption effectively enhances the water gas shift reaction producing a gas with a hydrogen volume fraction of over 90%. Multicycle tests of reforming/CO2 capture and regeneration were performed to verify the stability of the catalysts and sorbents to remove TAR and capture CO2 during the duty cycle.

Salvinorin A analogues PR-37 and PR-38 attenuate compound 48/80-induced itch responses in mice.

Science.gov (United States)

Salaga, M; Polepally, P R; Zielinska, M; Marynowski, M; Fabisiak, A; Murawska, N; Sobczak, K; Sacharczuk, M; Do Rego, J C; Roth, B L; Zjawiony, J K; Fichna, J

2015-09-01

The opioid system plays a crucial role in several physiological processes in the CNS and in the periphery. It has also been shown that selective opioid receptor agonists exert potent inhibitory action on pruritus and pain. In this study we examined whether two analogues of Salvinorin A, PR-37 and PR-38, exhibit antipruritic properties in mice. To examine the antiscratch effect of PR-37 and PR-38 we used a mouse model of compound 48/80-induced pruritus. In order to elucidate the mechanism of action of tested compounds, specific antagonists of opioid and cannabinoid receptors were used. The effect of PR-37 on the CNS was assessed by measuring motor parameters and exploratory behaviours in mice. PR-37 and PR-38, jnjected s.c., significantly reduced the number of compound 48/80-induced scratching behaviours in mice in a dose- and time-dependent manner. PR-38 was also active when orally administered. The antiscratch activity of PR-37 was blocked by the selective κ opioid receptor antagonist, nor-binaltorphimine, and that of PR-38 by the selective μ opioid receptor antagonist, β-funaltrexamine. In conclusion, a novel framework for the development of new antipruritic drugs derived from salvinorin A has been validated. © 2015 The British Pharmacological Society.

Nickel titanium springs versus stainless steel springs: A randomized clinical trial of two methods of space closure.

Science.gov (United States)

Norman, Noraina Hafizan; Worthington, Helen; Chadwick, Stephen Mark