Proceedings of the APPrO 2006 18. annual Canadian power conference and trade show : Green Power Conference : Canada's leading renewable energy conference

International Nuclear Information System (INIS)

Brooks, J.

2007-01-01

This conference provided a forum for members of the Association of Power Producers of Ontario to discuss recent developments in renewable energy and the electric power industry. An overview of Ontario's renewable standard offer program was provided. Members of the conference also discussed case studies of Ontario renewable energy projects including micro-hydro; anaerobic digesters; stand-alone wind power; and solar energy. The economics of wind power were discussed, and current capital costs for renewable energy technology projects were reviewed. Other topics included the use of base-load nuclear and hydro-electricity; the closing down of coal-fired generation; the integration of wind power; and natural gas and cogeneration. Issues related to interconnected power supplies were also reviewed. Discussions were divided into 5 topics : (1) an introduction to the standard offer program; (2) provincial procurement of green power; (3) case studies of stand-alone project; (4) distributed generation and the standard offer process; and distribution approval and connection issues. refs., tabs., figs

Design Considerations for the Electrical Power Supply of Future Civil Aircraft with Active High-Lift Systems

Directory of Open Access Journals (Sweden)

J.-K. Mueller

2018-01-01

Full Text Available Active high-lift systems of future civil aircraft allow noise reduction and the use of shorter runways. Powering high-lift systems electrically have a strong impact on the design requirements for the electrical power supply of the aircraft. The active high-lift system of the reference aircraft design considered in this paper consists of a flexible leading-edge device together with a combination of boundary-layer suction and Coanda-jet blowing. Electrically driven compressors distributed along the aircraft wings provide the required mass flow of pressurized air. Their additional loads significantly increase the electric power demand during take-off and landing, which is commonly provided by electric generators attached to the aircraft engines. The focus of the present study is a feasibility assessment of alternative electric power supply concepts to unburden or eliminate the generator coupled to the aircraft engine. For this purpose, two different concepts using either fuel cells or batteries are outlined and evaluated in terms of weight, efficiency, and technology availability. The most promising, but least developed alternative to the engine-powered electric generator is the usage of fuel cells. The advantages are high power density and short refueling time, compared to the battery storage concept.

Analysis of data from water lift powered by solar energy pump

Energy Technology Data Exchange (ETDEWEB)

Oyama, Paulo Takashi [Universidade Estadual do Oeste do Parana (UNIOESTE), Cascavel, PR (Brazil); Ricieri, Reinaldo Prandini [Universidade Estadual do Oeste do Parana (UNIOESTE), Cascavel, PR (Brazil). Dept. de Engenharia Agricola], E-mail: ricieri@unioeste.br; Halmeman, Maria Cristina Rodrigues [Universidade Estadual Paulista (UNESP), Botucatu, SP (Brazil); Gnoatto, Estor; Kavanagh; Brenneisen, Paulo Job [Universidade Tecnologica Federal do Parana (UTFPR), Medianeira, PR (Brazil)], Emails: gnoatto@utfpr.edu.br, kavanagh@utfpr.edu.br, brenneisen@utfpr.edu.br

2008-07-01

Due to the high costs to install electricity in remote locations, away from the regular urban electrical installations, photovoltaic solar energy has ample application in public illumination, water pumping, health services offices, etc. With the purpose to contribute to a better use of this kind of energy, this project aimed in analyzing the outflow and efficiency of a motor pump powered by photovoltaic panels, the irradiation necessary to activate it for water lift, collecting data at every 6- meter height, ranging from 6,2 to 18,2 meters. This study is part of a development project of the Universidade Tecnologica Federal do Parana (UTFPR), by making use of photovoltaic panels, motor pump, pyranometers, thermocouple type K, pressure transducer and outflow transducer. The data show a maximum average outflow of 584,299 Lh{sup -1} and maximum efficiency of 23,338% for a lift of 18,2 m. There is also the need of irradiation for the activation of the motor pump proportional to the height of the lift, in a polynomial dependence of the third order. (author)

CFD Study of a New Annular Lift Fan Configuration with High Lift Efficiency

Directory of Open Access Journals (Sweden)

Yun Jiang

2017-03-01

Full Text Available A new annular lift fan configuration that has very high lift efficiency is explored by using a numerical scheme. The inlet lip radius and diffuser angle are maximized by semicircle duct walls and the location of the lift fan is moved from the throat to the diffuser area to maximize the diffusion effect of the ducted fan. The improved lift fan achieves the figure of merit of 0.772 and the power loading of 9.03 lbs/hp without ground effect, very close to the theoretical limit. Under the ground effect, the figure of merit reaches 0.822 with the power loading of 9.62 lbs/hp. The improved lift efficiency deteriorates the transition characteristics with higher momentum drag and pitching moment. However, with the aid of jet thrusts directly providing part of the lift during transition, the peak of momentum drag and pitching moment can be lowered. A total thrust to weight ratio of 0.7 is enough for all of the requirements in transition and in hover and for the maximum speed of 0.75 Mach in cruise flight.

Development of an Upper Limb Power Assist System Using Pneumatic Actuators for Farming Lift-up Motion

Science.gov (United States)

Yagi, Eiichi; Harada, Daisuke; Kobayashi, Masaaki

A power assist system has lately attracted considerable attention to lifting-up an object without low back pain. We have been developing power assist systems with pneumatic actuators for the elbow and shoulder to farming support of lifting-up a bag of rice weighing 30kg. This paper describes the mechanism and control method of this power assist system. The pneumatic rotary actuator supports shoulder motion, and the air cylinder supports elbow motion. In this control method, the surface electromyogram(EMG) signals are used as input information of the controller. The joint support torques of human are calculated based on the antigravity term of necessary joint torques, which are estimated on the dynamics of a human approximated link model. The experimental results show the effectiveness of the proposed mechanism and control method of the power assist system.

Conference papers of POWER-GEN '93: Book 2

International Nuclear Information System (INIS)

Anon.

1993-01-01

The 6th International Conference and Exhibition for the Power Generating Industries was held November 17--19, 1993 in Dallas, Texas. The conference provided a forum for exchange of state-of-the-art information on power generation. Major topics of discussion include the following: environmental issues and technologies; and Clean Air Act compliance. Individual papers have been processed separately for inclusion in the appropriate data bases

CERN takes off at Lift11

CERN Multimedia

Katarina Anthony

2011-01-01

CERN was especially featured at the Lift11 conference, held in Geneva early this month. Tara Shears delivered a keynote speech at the event, while Paul Oortman Gerlings (DGS-SEE) and Erik van der Bij (BE-CO) – winners of the Bulletin’s Lift11 competition – organised the CERN workshop.   Paul Oortman Gerlings takes questions at CERN's Lift11 workshop. Lift11 was an opportunity for CERN to reach today’s innovators and developers. “The event was filled with people eager to learn new ideas, who were not afraid to ask questions,” says Tara Shears, physicist from the LHCb Collaboration who presented an update on the status of the LHC. “People were amazed by what goes on inside CERN, by our science, our facilities – even by the way we carry out our day-to-day work. It is a branch of fundamental research that really seems to inspire everyone.” A small Lift11 group had the chance to take a tour of CERN, ...

Lift and Power Required for Flapping Wing Hovering Flight on Mars

Science.gov (United States)

Pohly, Jeremy; Sridhar, Madhu; Bluman, James; Kang, Chang-Kwon; Landrum, D. Brian; Fahimi, Farbod; Aono, Hikaru; Liu, Hao

2017-11-01

Achieving flight on Mars is challenging due to the ultra-low density atmosphere. Bio-inspired flapping motion can generate sufficient lift if bumblebee-inspired wings are scaled up between 2 and 4 times their nominal size. However, due to this scaling, the inertial power required to sustain hover increases and dominates over the aerodynamic power. Our results show that a torsional spring placed at the wing root can reduce the flapping power required for hover by efficiently storing and releasing energy while operating at its resonance frequency. The spring assisted reduction in flapping power is demonstrated with a well-validated, coupled Navier-Stokes and flight dynamics solver. The total power is reduced by 79%, whereas the flapping power is reduced by 98%. Such a reduction in power paves the way for an efficient, realizable micro air vehicle capable of vertical takeoff and landing as well as sustained flight on Mars. Alabama Space Grant Consortium Fellowship.

GasFair and Power '99 and the Ontario Competitive Power Conference: proceedings of the 8. annual natural gas and electricity market conference

International Nuclear Information System (INIS)

1999-01-01

The 47 presentations at Enerdata's 1999 annual conference and trade show were divided between the GasFair and Power '99 Natural Gas and Electricity Market Conference, and the Ontario Competitive Power Conference. The four major sessions of GasFair and Power '99 included the: (1) gas track, (2) power track, (3) gas and power, and (4) forums and workshops. In general, the papers reviewed the recent activities in the natural gas and electric power industry in North America. The presentations highlighted the recent changes that are occurring as a result of deregulation and new environmental policies. The North American electric power and natural gas industry are moving towards competition. Most market participants will benefit from this change because it creates a more level playing field. Several papers also discussed issues regarding the long-term outlook for new Canadian gas supplies to eastern and midwest markets. Some of the other topics discussed included issues regarding the impact of basis tradin g, tools of the energy marketer, and the advantages of pipeline planning. The challenges facing Ontario Hydro to diversify their existing power generation and to use natural gas for power generation in order to meet energy demand was also discussed. tabs., figs

11 World power conference

International Nuclear Information System (INIS)

Masters, R.

1981-01-01

Papers presented to the 11 World power conference ''Power for our peace'' held in Munich in September, 1980 are shortly surveyed. A few papers were devoted to nuclear power, that represents its present- state-of-the-art in the world. Except for the paper presented by experts of the International Energy Agency (IEA) and a number of others, there is carefulness and realism with respect to nuclear power in the most part of the papers; its forecasted growth rates are rather moderate. Even in the IEA paper the total world nuclear installed capacity in 1985 is evaluated about 550 GW, that is substantially smaller earlier evaluations. It is acknowledged that the primary energy production almost in all countries will increase mainly due to nuclear power and coal. But there are no answers to the problems related to management of the nuclear power development and to the public opinion in many countries. It is underlined that the problems of world power supply can be solved only on an international basis [ru

Insight conference proceedings : Alberta power

International Nuclear Information System (INIS)

2004-01-01

This conference addressed issues dealing with Alberta's restructured electric power industry and new policies from the perspective of Alberta's independent power industry. It covered lessons learned from electric industry restructuring, transmission strategies, transmission frameworks, competitive markets, power costs, energy prices, and power outages. Interconnected power systems between Alberta and British Columbia were also reviewed along with grid reinforcement requirements. Markets and restructuring efforts in other jurisdictions such as Quebec and Maritime Canada were briefly reviewed. The move to deregulate the industry has played an important role in restructuring a vertically integrated industry into power generation, transmission and distribution. High electricity prices eventually resulted in re regulation of the industry and a synergy between wholesale and retail markets. Five of the 17 papers were indexed separately for inclusion in the database. refs., tabs., figs

Insight conference reports : BC power summit

International Nuclear Information System (INIS)

2004-01-01

The papers presented at this conference described recent events and activities in the power industry in British Columbia. Issues concerning distribution, supply and demand were examined as well as the implications of the August blackout to the electric power industry as a whole. Supply initiatives and challenges were examined, including alternative energy initiatives and possibilities for the future. Financing structures and strategies of renewable energy projects were evaluated. The role of regulators was examined as well as details of deregulation in the Pacific North West. Infrastructure development in Alberta was reviewed. Resource planning guidelines were examined. Financing, project financing, demand side management and energy conservation in British Columbia were also discussed. The conference featured 21 presentations, of which 4 have been catalogued separately for inclusion in this database. tabs, figs

GasFair and Power '99 and the Ontario Competitive Power Conference: proceedings of the 8. annual natural gas and electricity market conference

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

The 47 presentations at Enerdata's 1999 annual conference and trade show were divided between the GasFair and Power '99 Natural Gas and Electricity Market Conference, and the Ontario Competitive Power Conference. The four major sessions of GasFair and Power '99 included the: (1) gas track, (2) power track, (3) gas and power, and (4) forums and workshops. In general, the papers reviewed the recent activities in the natural gas and electric power industry in North America. The presentations highlighted the recent changes that are occurring as a result of deregulation and new environmental policies. The North American electric power and natural gas industry are moving towards competition. Most market participants will benefit from this change because it creates a more level playing field. Several papers also discussed issues regarding the long-term outlook for new Canadian gas supplies to eastern and midwest markets. Some of the other topics discussed included issues regarding the impact of basis trading, tools of the energy marketer, and the advantages of pipeline planning. The challenges facing Ontario Hydro to diversify their existing power generation and to use natural gas for power generation in order to meet energy demand was also discussed. tabs., figs.

Proceedings of AsiaPES 2007 : Asian power and energy systems conference

Energy Technology Data Exchange (ETDEWEB)

Ongsakul, W. [Asian Inst. of Technology, Pathumthani (Thailand)] (ed.)

2007-07-01

This energy and power systems conference provided a forum for international researchers and power industry members to discuss recent technological innovations related to power systems. New technologies and modelling strategies for power systems were identified along with issues related to artificial intelligence and design optimization. The role of renewable energy sources such as solar, wind and biomass energy in interconnected power systems were also reviewed. The conference was divided into 8 sessions entitled: (1) control, protection, power flow and design, (2) planning and operation, (3) alternative energy, (4) stability, reliability, forecasting and load shedding, (5) phasor measurement and power quality, (6) distribution, analysis, technology and policy (7) energy efficiency, storage and pricing, and (8) a special session on the application of phasor measurement units to monitor wide area power system dynamics. The conference featured 88 presentations, of which 63 have been catalogued separately for inclusion in this database. refs., tabs., figs.

Nordic wind power conference 2007. Proceedings

International Nuclear Information System (INIS)

Cutululis, Nicolaos; Soerensen, Poul

2007-11-01

This fourth Nordic Wind Power Conference was focused on power system integration and electrical systems of wind turbines and wind farms. NWPC presents the newest research results related to technical electrical aspects of wind power, spanning from power system integration to electrical design and control of wind turbines. The first NWPC was held in Trondheim (2000), Norway, the second in Gothenburg (2004), Sweden, and the third in Espoo (2006), Finland. Invited speakers, oral presentation of papers and poster sessions ensured this to be a valuable event for professionals and high-level students wanting to strengthen their knowledge on wind power integration and electrical systems. (au)

Nordic wind power conference 2007. Proceedings

Energy Technology Data Exchange (ETDEWEB)

Cutululis, N; Soerensen, P [eds.

2007-11-15

This fourth Nordic Wind Power Conference was focused on power system integration and electrical systems of wind turbines and wind farms. NWPC presents the newest research results related to technical electrical aspects of wind power, spanning from power system integration to electrical design and control of wind turbines. The first NWPC was held in Trondheim (2000), Norway, the second in Gothenburg (2004), Sweden, and the third in Espoo (2006), Finland. Invited speakers, oral presentation of papers and poster sessions ensured this to be a valuable event for professionals and high-level students wanting to strengthen their knowledge on wind power integration and electrical systems. (au)

Development of a power-assisted lifting device for construction and periodic inspection

International Nuclear Information System (INIS)

Hayatsu, M.; Yamada, M.; Takasu, H.; Tagawa, Y.; Kajiwara, K.

2001-01-01

This study focuses on the control system design and control performance of a power-assisted lifting device. The device consists of several electric chain-blocks, each controlled by force sensors and a CPU. The mechanism is as follows: (1) Force sensors detect any chain tension changes (by human force), (2) The CPU calculates the required output, (3) Electric chain-blocks move the object in the intended direction. The feature of this device is that it does not require any information related to the suspension points of the electric chain-blocks. The controller was designed using the H method, which considers disturbances and aims to provide robust stability under the operation conditions of construction verified through experiments using a 700 kg steel dummy mass (control object) suspended by four electric chain-blocks. In the experiments, the controller, which was designed using the H method, was compared to the PI controller method, and the effectiveness of the H controller was proven. A control object could be moved, translated, and rotated by human force (of less than 10 kg). Positioning performance errors were suppressed to less than 0.5 mm, and operation time was reduced by about 50%. This device will improve working efficiency and rationalize lifting operations in nuclear power plants. (author)

Development of a power-assisted lifting device for construction and periodic inspection

Energy Technology Data Exchange (ETDEWEB)

Hayatsu, M.; Yamada, M.; Takasu, H. [Hitachi Plant Engineering and Construction, Chiba-ken (Japan); Tagawa, Y. [Tokyo Univ. of Agriculture and Technology (Japan); Kajiwara, K. [National Research Institute for Earth Science and Disaster Prevention, Tokyo (Japan)

2001-07-01

This study focuses on the control system design and control performance of a power-assisted lifting device. The device consists of several electric chain-blocks, each controlled by force sensors and a CPU. The mechanism is as follows: (1) Force sensors detect any chain tension changes (by human force), (2) The CPU calculates the required output, (3) Electric chain-blocks move the object in the intended direction. The feature of this device is that it does not require any information related to the suspension points of the electric chain-blocks. The controller was designed using the H method, which considers disturbances and aims to provide robust stability under the operation conditions of construction verified through experiments using a 700 kg steel dummy mass (control object) suspended by four electric chain-blocks. In the experiments, the controller, which was designed using the H method, was compared to the PI controller method, and the effectiveness of the H controller was proven. A control object could be moved, translated, and rotated by human force (of less than 10 kg). Positioning performance errors were suppressed to less than 0.5 mm, and operation time was reduced by about 50%. This device will improve working efficiency and rationalize lifting operations in nuclear power plants. (author)

The World Power Conference and atomic energy

Energy Technology Data Exchange (ETDEWEB)

NONE

1962-01-15

The possibility that emerged after the last World War that useful power could be produced from nuclear fission led to optimistic estimates that nuclear power would prove to be the solution to the world's energy problems. The possible advantages of nuclear methods of power production compared with conventional means are discussed at the World Power Conference. The 1962 Conference with its theme 'The Changing Pattern of Power' will undoubtedly attract great interest in a world where the change-over from conventional to nuclear fuels for power production has started in some countries and is being actively examined in others. It is generally being realized that even though a country may possess indigenous supplies of uranium or thorium minerals, the building up of a nuclear industry i s a long and expensive process and the alternative of depending on countries more advanced in nuclear technology for the supply of materials, skill and know-how is costly in foreign exchange and international prestige. Many of the industrialized countries, still possessing supplies of conventional fuels, are preparing for the day when their reserves will become depleted and are embarking on training schemes to ensure a continuing supply of engineers and scientists skilled in nuclear arts

Proceedings of the 10. IASTED international conference on power and energy systems (PES 2008)

Energy Technology Data Exchange (ETDEWEB)

Fuchs, E. (ed.)

2008-07-01

This conference provided a forum to review new technologies and modelling strategies for power systems and to address issues related to artificial intelligence and power system design optimization. The role of renewable energy sources such as solar, wind and biomass energy in interconnected power systems were also reviewed. In addition, conference participants presented recent advances in distributed power generation; load shedding; fault diagnosis; energy storage; power system stability; and security of supply. The sessions of the conference were entitled: fault detection, diagnosis, protection and power quality; renewable, distributed, generation and power lines; power system analysis, operation and control; and electricity markets. The conference featured 43 presentations, of which 24 have been catalogued separately for inclusion in this database. refs., tabs. figs.

Insight conference reports : proceedings of the 7. annual Alberta power summit

International Nuclear Information System (INIS)

2006-01-01

This power summit conference provided a forum to discuss issues related to electricity transmission and distribution in Canada. The conference addressed recent regulatory and policy changes related to the electricity industry and provided an update on the Alberta Independent System Operator (AESO). Recent developments in wind power development and integration were also outlined, as well as issues related to power markets. Financial incentive regulations in Ontario were reviewed along with the current status of clean coal technologies. Issues related to biomass energy and rural electrification were also reviewed. One of the 17 presentations featured at this conference has been catalogued separately for inclusion in this database. refs., tabs., figs

12. national conference of Czechoslovak power specialists

International Nuclear Information System (INIS)

1983-01-01

The XIIth national conference of Czechoslovak power specialists was held in Bratislava from October 5 to 7, 1983. Of the total number of 32 papers 12 were incorporated in the INIS system, i.e., such which dealt with the development of the nuclear power complex and the rationalization of sources and the use of heat in the Czechoslovak energy balance. (E.S.)

Fuel-Conservation Guidance System for Powered-Lift Aircraft

Science.gov (United States)

Erzberger, Heinz; McLean, John D.

1981-01-01

A technique is described for the design of fuel-conservative guidance systems and is applied to a system that was flight tested on board NASA's sugmentor wing jet STOL research aircraft. An important operational feature of the system is its ability to rapidly synthesize fuel-efficient trajectories for a large set of initial aircraft positions, altitudes, and headings. This feature allows the aircraft to be flown efficiently under conditions of changing winds and air traffic control vectors. Rapid synthesis of fuel-efficient trajectories is accomplished in the airborne computer by fast-time trajectory integration using a simplified dynamic performance model of the aircraft. This technique also ensures optimum flap deployment and, for powered-lift STOL aircraft, optimum transition to low-speed flight. Also included in the design is accurate prediction of touchdown time for use in four-dimensional guidance applications. Flight test results have demonstrated that the automatically synthesized trajectories produce significant fuel savings relative to manually flown conventional approaches.

Effects of a Belt on Intra-Abdominal Pressure during Weight Lifting.

Science.gov (United States)

1988-03-01

potentially injurious b compressive forces on spinal discs during lifting. To investigate the effects of a standard lifting belt on lAP and lifting mechanics... injurious compressive forces on spinal discs during lifting. To investigate the effects of a standard lifting belt on IAP and lifting ! mechanics... weightlifting (7,9). Both olympic and power lifters have used lifting belts for many years, yet virtually no research has been reported which examines

Application of powered lift and mechanical flap concepts for civil short-haul transport aircraft design

Science.gov (United States)

Conlon, J. A.; Bowles, J. V.

1977-01-01

The objective of this paper is to determine various design and performance parameters, including wing loading and thrust loading requirements, for powered-lift and mechanical flap conceptual aircraft constrained by field length and community noise impact. Mission block fuel and direct operating costs (DOC) were found for optimum designs. As a baseline, the design and performance parameters were determined for the aircraft using engines without noise suppression. The constraint of the 90 EPNL noise contour being less than 2.6 sq km (1.0 sq mi) in area was then imposed. The results indicate that for both aircraft concepts the design gross weight, DOC, and required mission block fuel decreased with field length. At field lengths less than 1100 m (3600 ft) the powered lift aircraft had lower DOC and block fuel than the mechanical flap aircraft but produced higher unsuppressed noise levels. The noise goal could easily be achieved with nacelle wall treatment only and thus resulted in little or no performance or weight penalty for all studied aircraft.

Wind tower service lift

Science.gov (United States)

Oliphant, David; Quilter, Jared; Andersen, Todd; Conroy, Thomas

2011-09-13

An apparatus used for maintaining a wind tower structure wherein the wind tower structure may have a plurality of legs and may be configured to support a wind turbine above the ground in a better position to interface with winds. The lift structure may be configured for carrying objects and have a guide system and drive system for mechanically communicating with a primary cable, rail or other first elongate member attached to the wind tower structure. The drive system and guide system may transmit forces that move the lift relative to the cable and thereby relative to the wind tower structure. A control interface may be included for controlling the amount and direction of the power into the guide system and drive system thereby causing the guide system and drive system to move the lift relative to said first elongate member such that said lift moves relative to said wind tower structure.

Substantiation of health related power lifting training methodic for univeristies students with muscular skeletal apparatuse affections.

Directory of Open Access Journals (Sweden)

San. Zhen Qiang

2015-11-01

Full Text Available Purpose: substantiation of health related power lifting training methodic for universities students, who have disorders of muscular skeletal apparatus. Material: in experimental researches 126 students of 18-24 years’ age, having disorders of muscular skeletal apparatus, participated. With the help of testing we registered changes of students’ functional, physical and psycho-physiological fitness indicators. Results: optimal correlation of specific and non specific loads was found: 60% of specific and 40% of non specific. It is recommended to follow certain correlation of exercises in easy and complicated conditions: for first year students - 3:2; for second year students - 3:2; for third year - 2:3; for forth year - 2:3; for fifth year students - 1:3. Specific only for power lifting conditions and temps of students’ (with muscular skeletal apparatus affections functional, physical and psycho-physiological fitness improvement were determined. Conclusions: The requirements of the training methodic envisage correction of loads for bringing every indicator on proper level.

Lifting devices in nuclear power plants

International Nuclear Information System (INIS)

Anon.

1978-01-01

The regulation applies to lifts, cranes, winches, rail trolleys, load pick-up equipment and fuel charging machines for LWR reactors, as far as these are employed in plants for the production or fission of nuclear fuels or for the reprocessing of spent nuclear fuels or for the storage or other uses of nuclear fuels. (orig.) 891 HP [de

New multi-purpose lifting devices for the Grafenrheinfeld and Unterweser nuclear power plants; Neue Kombihebetraversen fuer die Kernkraftwerke Grafenrheinfeld und Unterweser

Energy Technology Data Exchange (ETDEWEB)

Aiglsdorfer, Christoph [Siempelkamp Nukleartechnik GmbH, Linz (Austria)

2011-03-15

After the extremely successful use of the multi-purpose lifting device and the reactor pressure vessel sealing head for the Brokdorf nuclear power plant, supplied by Siempelkamp Nukleartechnik in 2008 and 2009, a further contract was received in early 2010. E.ON Kernkraft decided to also order a multi-purpose lifting device each for the power plants at Grafenrheinfeld and Unterweser from Siempelkamp. The important innovation of the Siempelkamp multi-purpose lifting device is that it is manufactured entirely from austenitic steel. This allows it to remain in its storage location on the retracted upper core grid (UCG) in the flooded reactor pool during the unloading of the fuel elements, while the fuel elements are being changed. The advantage here for the operator is that the fuel elements change is shortened even further, and this reduces costs. Saving time is also an important requirement for the RPV sealing head. For the Brokdorf nuclear power plant, Siempelkamp manufactured and supplied the RPV sealing head. A precondition of this order was a total realisation time of seven months and to save valuable time during the outage for the operating company. With a new sealing concept, a further innovation from Siempelkamp came to bear on this contract. It makes it possible to safely handle the RPV sealing head using the multi-purpose lifting device. (orig.)

VGB conference 'Chemistry in the power plant 1984' - VGB feedwater conditioning conference

International Nuclear Information System (INIS)

1984-01-01

The conference bears various aspects of feedwater conditioning for power plant cooling systems and steam generators as well as on the analytical assessment of water quality and its translation into operational method approaches. 5 out of the total 14 papers were entered separately in the database. (RB) [de

Operating Experience with Power Reactors. Proceedings of the Conference on Operating Experience with Power Reactors. Vol. I

Energy Technology Data Exchange (ETDEWEB)

NONE

1963-10-15

At the beginning of 1963 nuclear power plants produced some 3 500 000kW of electrical power to different distribution grids around the world. Much significant operating experience has been gained with these power reactors, but this experience is often not collected in such a way as to make it easily available. The International Atomic Energy Agency convened a Conference on Operating Experience with Power Reactors in Vienna from 4-8 June 1963 which was attended by 240 participants representing 27 of the Agency's Member States and six international organizations. At the Conference, 42 papers giving detailed experience with more than 20 nuclear power stations were discussed. Although similar meetings on a national or regional scale have been held earlier in various countries, this is the first arranged by the Agency on a world-wide basis. Some of the detailed material may have been given earlier but for the most part it represents new and recently acquired experience, and for the first time it has been possible to compile in one place such extensive material on the operating experience with power reactors. The Conference discussed the experience gained both generally in the context of national and international nuclear power development programmes, and more specifically in the detailed operating experience with different power reactor stations. In addition, various plant components, fuel cycles, staffing of nuclear plants and licensing of such staff were treated. It is hoped that these Proceedings will be of interest not only to nuclear plant designers and operators who daily encounter problems similar to those discussed by the Conference, but also to those guiding the planning and implementation of power development programmes.

Operating Experience with Power Reactors. Proceedings of the Conference on Operating Experience with Power Reactors. Vol. II

Energy Technology Data Exchange (ETDEWEB)

NONE

1963-10-15

At the beginning of 1963 nuclear power plants produced some 3 500 000 kW of electrical power to different distribution grids around the world. Much significant operating experience has been gained with these power reactors, but this experience is often not collected in such a way as to make it easily available. The International Atomic Energy Agency convened a Conference on Operating Experience with Power Reactors in Vienna from 4 -8 June 1963 which was attended by 240 participants representing 27 of the Agency's Member States and six international organizations. At the Conference, 42 papers giving detailed experience with more than 20 nuclear power stations were discussed. Although similar meetings on a national or regional scale have been held earlier in various countries, this is the first arranged by the Agency on a world-wide basis. Some of the detailed material may have been given earlier but for the most part it represents new and recently acquired experience, and for the first time it has been possible to compile in one place such extensive material on the operating experience with power reactors. The Conference discussed the experience gained both generally in the context of national and international nuclear power development programmes, and more specifically in the detailed operating experience with different power reactor stations. In addition, various plant components, fuel cycles, staffing of nuclear plants and licensing of such staff were treated. It is hoped that these Proceedings will be of interest not only to nuclear , plant designers and operators who daily encounter problems similar to those discussed by the Conference, but also to those guiding the planning and implementation of power development programmes.

Proceedings of the 4. IASTED Asian conference on power and energy systems : AsiaPES 2008

Energy Technology Data Exchange (ETDEWEB)

Nor, K.M. [Technological Univ. of Malaysia, Kuala Lumpur (Malaysia)] (ed.)

2008-07-01

Recent technological innovations related to power systems were presented at this international energy and power systems conference. New technologies and modelling strategies for power systems were identified along with issues related to artificial intelligence and design optimization. The role of renewable energy sources such as solar, wind and biomass energy in interconnected power systems were also reviewed. The conference was divided into 9 sessions entitled: (1) distribution systems, (2) electromagnetic fields, (3) power quality, (4) power system operations, (5) power system planning, (6) power system protection, (7) power system stability, (8) renewable energy, and (9); thermal systems. All 68 presentations from the conference have been catalogued separately for inclusion in this database. refs., tabs., figs.

PREFACE: 14th International Conference on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2014)

Science.gov (United States)

2014-11-01

It is our great pleasure to welcome you to the 14th International Conference on Micro- and Nano-Technology for Power Generation and Energy Conversion Applications, or PowerMEMS 2014, in Awaji Island, Japan. The aim of PowerMEM is to present the latest research results in the field of miniature, micro- and nano-scale technologies for power generation and energy conversion. The conference will also- give us the opportunity to exchange informations and new ideas in the field of Power MEMS/NEMS. The current status of the field of PowerMEMS spans the full spectrum from basic research to practical applications. We will enjoy valuable discussions not only from the viewpoint of academia but from commercial and industrial perspectives. In the conference, three invited speakers lead the technical program. We received 172 abstracts and after a careful reviewing process by the Technical Program Committee a total of 133 papers were selected for presentation. These have been organized into 16 Oral sessions in two parallel streams and two poster sessions including some late-news papers. The oral and regular poster papers are published by the Institute of Physics (IOP). We have also organized a PowerMEMS School in Kobe-Sannomiya contiguous to the main conference. This two-day school will cover various topics of energy harvesting. World leading experts will give invited lectures on their main topics. This is a new experiment to broaden the technology remit of our conference by organizing mini symposiums that aim to gather the latest research on the following topics by the organizers: Microscale Combustion, Wideband Vibration Energy Harvesting, RF Energy Transfer and Industrial Application. We hope this, and other activities will make PowerMEMS2014 a memorable success. One of the important programs in an international conference is the social program, and we prepare the PowerMEMS2014 banquet in the banquet room at the Westin Awaji Island Hotel. This will provide an opportunity to

Vertical Lift by Series Hybrid Power, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — A major market for vertical lift aircraft is in urban operations, primarily for police and electronic news gathering (typically a Bell 206 or a Eurocopter AS350)....

Proceedings of the CERI 2006 electricity conference : the challenges of powering Canada's growth

International Nuclear Information System (INIS)

2006-01-01

Decision makers in the electric power industry face continuing challenges regarding changes in electricity market mechanisms, pricing options, and power generation and transmission alternatives. This conference provided an opportunity to review energy markets in North American with particular reference to supply and demand. Opportunities for traditional or new generation technologies based on renewable energy sources including wind powered generation were discussed. The presentations focused on transmission issues, market design and capacity issues as well as market power and pricing. The integration of wind energy into the power grid as a measure to diversify the power generation portfolio in North America was also discussed along with hydrothermal synergies and interconnections. The sessions of the conference were entitled: future generation and market operations in Canada; risks, challenges and opportunities for transmission in Canada; wind power and system integration issues; the role of consumers and demand side management in Canada; cogeneration in Alberta and Canada; and, regulatory issues in Canadian electricity markets. The conference featured 25 presentations, of which 10 have been catalogued separately for inclusion in this database. tabs., figs

Insight conference reports : Alberta power summit

International Nuclear Information System (INIS)

2003-01-01

The 18 presentations at this conference covered a wide range of topics dealing with the Canada's electric power industry. Issues of particular concern included lessons learned from restructuring in Alberta, Ontario and New Brunswick, as well as credit risk management in the power sector, power marketing in Alberta, and transmission issues. The challenges facing the industry regarding climate change and the commitment made by Canada under the Kyoto Protocol to reduce greenhouse gas emissions was also discussed with particular reference to emissions trading and the need to harmonize environmental policies between federal and provincial jurisdictions. The move to deregulate the industry played an important role in restructuring a vertically integrated industry into power generation, transmission and distribution. High electricity prices eventually resulted in re regulation of the industry and a synergy between wholesale and retail markets. Four of the 18 papers were indexed separately for inclusion in the database. refs., tabs., figs

Proceedings of the American Power Conference. Volume 58-II

International Nuclear Information System (INIS)

McBride, A.E.

1996-01-01

This book is part 2 of the proceedings of the American Power Conference, Technology for Competition and Globalization, 1996. The topics of the papers include structural plant design; challenges of the global marketplace; thermal hydraulic methods for nuclear power plant safety and operation; decontamination and decommissioning; competitive operations and maintenance; fuel opportunities; cooling; competitive power pricing; operations; transformers; relays; plant controls; training to meet the competitive future; burning technologies; ash and byproducts utilization; advanced systems; computer tools for plant design; globalization of power; power system protection and power quality; life extension; grounding; and transmission line equipment

ARC Researchers at IEEE 2015 Vehicle Power and Propulsion Conference

Science.gov (United States)

Contacts Researchers News & Events Event Calendar Annual Program Review Research Seminars Press Room Event Archives ARC Researchers at the IEEE 2015 Vehicle Power and Propulsion Conference (October 19-22 Ballroom B P-SS4-2 Comparison of SOFC and PEM Fuel Cell Hybrid Power Management Strategies for Mobile

The Circulation Distribution on the Lifting Line for a Given Extracted Power

Directory of Open Access Journals (Sweden)

Ali Helali

2012-01-01

Full Text Available Presently, there exist few numerical methods which treat the inverse problem for the determination of the geometry of wind turbine blades. In this work, authors intend to solve the inverse optimum project for horizontal axis wind turbine in which the selection of the circulation distribution is obtained by resolving two variational problems: the first consists in sorting the circulation distribution on the lifting line, which, for a given power extracted by the wind turbine, minimizes the loses due to the induced velocity. In the second, the optimal circulation distribution is selected such that the kinetic energy of the wind downstream of the rotor disc is minimum, when the energy extracted by the wind turbine for one rotating period is imposed. A code has been developed which incorporates the real pitch of the helicoidal vortex wake. Very promising results have been obtained: the circulation distribution for a given extracted power and the chord lengths distribution law along the blade span.

A Simple Method for High-Lift Propeller Conceptual Design

Science.gov (United States)

Patterson, Michael; Borer, Nick; German, Brian

2016-01-01

In this paper, we present a simple method for designing propellers that are placed upstream of the leading edge of a wing in order to augment lift. Because the primary purpose of these "high-lift propellers" is to increase lift rather than produce thrust, these props are best viewed as a form of high-lift device; consequently, they should be designed differently than traditional propellers. We present a theory that describes how these props can be designed to provide a relatively uniform axial velocity increase, which is hypothesized to be advantageous for lift augmentation based on a literature survey. Computational modeling indicates that such propellers can generate the same average induced axial velocity while consuming less power and producing less thrust than conventional propeller designs. For an example problem based on specifications for NASA's Scalable Convergent Electric Propulsion Technology and Operations Research (SCEPTOR) flight demonstrator, a propeller designed with the new method requires approximately 15% less power and produces approximately 11% less thrust than one designed for minimum induced loss. Higher-order modeling and/or wind tunnel testing are needed to verify the predicted performance.

Regional changes in spine posture at lift onset with changes in lift distance and lift style

NARCIS (Netherlands)

Gill, K.P.; Bennet, S.J.; Savelsbergh, G.J.P.; van Dieen, J.H.

2007-01-01

STUDY DESIGN. Repeated measures experiment. OBJECTIVE. To determine the effect of changes in horizontal lift distance on the amount of flexion, at lift onset, in different spine regions when using different lift styles. SUMMARY OF BACKGROUND DATA. By approximating spine bending during lifting as a

Proceedings of the 9. IASTED international conference on power and energy systems

Energy Technology Data Exchange (ETDEWEB)

Domijan, A.Jr. [Univ. of South Florida, Tampa, FL (United States)

2007-07-01

This conference provided an international forum for researchers and practitioners to exchange ideas and practical experience in the field of energy and power systems. The purpose was to strengthen relations between the energy sector, research laboratories and universities. Discussions focused on reliability issues in the next generation of power systems. Environmental factors and customer concerns regarding power quality issues were noted as the driving force for new concepts in electricity demand. Global and regional energy challenges ranging from energy production to power delivery were also discussed. The sessions of the conference were entitled: power system planning, investment, real time management and operations; infrastructure, reliability and weather effects; alternate energy developments and sustainability using biomass, solar and other renewable energy sources; modelling power systems, demand response and end use, and tariff issues; power quality, filtering, and experimental performance evaluations; forecasting computational methods and electronics; distribution system issues, microturbines and microgrids; and, nuclear power plants, modelling and evaluation of energy systems. All 72 presentations were catalogued separately for inclusion in this database. refs., tabs., figs.

Proceedings of the 9. IASTED international conference on power and energy systems

International Nuclear Information System (INIS)

Domijan, A.Jr.

2007-01-01

This conference provided an international forum for researchers and practitioners to exchange ideas and practical experience in the field of energy and power systems. The purpose was to strengthen relations between the energy sector, research laboratories and universities. Discussions focused on reliability issues in the next generation of power systems. Environmental factors and customer concerns regarding power quality issues were noted as the driving force for new concepts in electricity demand. Global and regional energy challenges ranging from energy production to power delivery were also discussed. The sessions of the conference were entitled: power system planning, investment, real time management and operations; infrastructure, reliability and weather effects; alternate energy developments and sustainability using biomass, solar and other renewable energy sources; modelling power systems, demand response and end use, and tariff issues; power quality, filtering, and experimental performance evaluations; forecasting computational methods and electronics; distribution system issues, microturbines and microgrids; and, nuclear power plants, modelling and evaluation of energy systems. All 72 presentations were catalogued separately for inclusion in this database. refs., tabs., figs

Heavy Lift for Exploration: Options and Utilization

Science.gov (United States)

Creech, Steve; Sumrall, Phil

2010-01-01

Every study of exploration capabilities since the Apollo Program has recommended the renewal of a heavy lift launch capability for the United States. NASA is aggressively pursuing that capability. This paper will discuss several aspects of that effort and the potential uses for that heavy lift capability. The need for heavy lift was cited most recent in the findings of the Review of U.S. Human Space Flight Plans Committee. Combined with considerations of launch availability and on-orbit operations, the Committee finds that exploration will benefit from the availability of a heavy-lift vehicle, the report said. In addition, heavy lift would enable the launching of large scientific observatories and more capable deep-space missions. It may also provide benefit in national security applications. The most recent focus of NASA s heavy lift effort is the Ares V cargo launch vehicle, which is part of the Constellation Program architecture for human exploration beyond low Earth orbit (LEO). The most recent point-of-departure configuration of the Ares V was approved during the Lunar Capabilities concept Review (LCCR) in 2008. The Ares V first stage propulsion system consists of a core stage powered by six commercial liquid hydrogen/liquid oxygen (LH2/LOX) RS-68 engines, flanked by two 5.5-segment solid rocket boosters (SRBs) based on the 5-segment Ares I first stage. The boosters use the same Polybutadiene Acrylonitrile (PBAN) propellant as the Space Shuttle. Atop the core stage is the Earth departure stage (EDS), powered by a single J-2X upper stage engine based on the Ares I upper stage engine. The 33-foot-diameter payload shroud can enclose a lunar lander, scientific instruments, or other payloads. Since LCCR, NASA has continued to refine the design through several successive internal design cycles. In addition, NASA has worked to quantify the broad national consensus for heavy lift in ways that, to the extent possible, meet the needs of the user community.

Proceedings of the American Power Conference. Volume 58-I

International Nuclear Information System (INIS)

McBride, A.E.

1996-01-01

This is volume 58-I of the proceedings of the American Power Conference, 1996, Technology for Competition and Globalization. The topics of the papers include power plant DC issues; cost of environmental compliance; advanced coal systems -- environmental performance; technology for competition in dispersed generation; superconductivity technologies for electric utility applications; power generation trends and challenges in China; aging in nuclear power plants; innovative and competitive repowering options; structural examinations, modifications and repairs; electric load forecasting; distribution planning; EMF effects; fuzzy logic and neural networks for power plant applications; electrokinetic decontamination of soils; integrated gasification combined cycle; advances in fusion; cooling towers; relays; plant controls; flue gas desulfurization; waste product utilization; and improved technologies

Proceedings of the 2008 CIGRE Canada conference on power systems : technology and innovation for the Canadian power grids of the future

International Nuclear Information System (INIS)

2008-01-01

The Conseil International des Grands Reseaux Electriques (CIGRE) promotes technical, economic and environmental developments in electricity transmission and generation. CIGRE Canada is one of 53 national committees of CIGRE. This conference showcased Canadian contributions to the electric power industry and how technology and innovation in the future will influence North American power grids. It provided a forum to discuss technological developments in the electric power industry and present products and services for electrical power systems. Issues concerning the interconnection of non traditional energy sources to the power systems were also discussed along with recent research initiatives related to renewable energy source development. The sessions of the conference were entitled: wind reliability and forecasting; substation automation and communication; human resources and long range planning; power system protection and control; distributed generation; electric vehicles and renewable energy; HVDC and facts; modeling and simulation; markets; overhead transmission lines; and new sensor and de-icing technologies and data management systems. All 68 presentations featured at this conference have been catalogued separately for inclusion in this database. refs., tabs., figs

Tornado lift

OpenAIRE

Ivanchin, Alexander

2010-01-01

It is shown that one of the causes for tornado is Tornado Lift. At increasing vortex diameter its kinetic energy decreases to keep the moment of momentum constant. A kinetic energy gradient of such vortex is Tornado Lift. Evaluation shows that contribution of Tornado Lift in air lifting in a tornado is comparable to buoyancy according to the order of magnitude.

Proceedings of the American Power Conference. Volume 60-2

International Nuclear Information System (INIS)

McBride, A.E.

1998-01-01

The American Power Conference, 60th annual meeting, 1998, addressed reliability and economy as related to technology for competition and globalization. The topics of the papers included needs and advances in power engineering education, global climate change, distributed generation, the critical role of the nations largest coal, nuclear and hydropower stations, advances in generation technology, financing electric power projects, successful deregulation, year 2000 outlook for equipment conflict with information and control, system planning, asset management, relay and communication, particulate and SO x control, environmental protection compliance strategies, fuel cells, gas turbines, renewable energy, steam turbines, and cost reduction strategies

Insight conference reports : proceedings of the 5. annual Ontario power forum

International Nuclear Information System (INIS)

2006-01-01

This conference provided a forum for members of the electricity industry and other stakeholders to discuss current trends and issues related to electricity generation in Ontario. Presentations given at the conference examined challenges in supply and demand as well as recent changes in local distribution companies. Issues related to the use of nuclear energy were discussed, and new business models using nuclear energy as a primary source of energy were reviewed. Members at the conference also discussed issues related to coal-fired generating plants and new advances in clean coal technology. Electricity prices were also discussed and issues related to wind power integration and electricity generation were reviewed. One of the 20 presentations featured at this conference has been catalogued separately for inclusion in this database. refs., tabs., figs

10th Handelsblatt annual 'power economy' conference

International Nuclear Information System (INIS)

Anon.

2003-01-01

Deregulation, internationalization, and EU enlargement within the confines of sustainability and competition were the overriding topics of this year's 10th Handelsblatt annual 'Power Economy' conference. Leading presenters from politics, industry, public authorities, and administration gave papers on these subjects for subsequent discussion. Expectations of Europe were clearly underlined. Europe has an important key function in the integration and shaping of a future energy supply system in the light of all societal, political, economic, and ecological factors. (orig.)

National conference on radiation safety of nuclear power plants and their environmental impacts

International Nuclear Information System (INIS)

Moravek, J.

1989-01-01

The first national conference on radiation safety of nuclear power plants and their environmental impacts was held in Tale (CS), 12 to 15 October, 1987 with the participation of 201 Czechoslovak specialists representing central authorities, research institutes, institutions of higher education, power plants in operation and under construction, water management and hygiene inspection and some production sectors, specialists from Hungary, Poland and the GDR. The participants heard 110 papers. The conference agenda comprised keynote papers presented in plenary session and five specialist sessions: 1. Radiation control of discharges and their surroundings. 2. Monitoring and evaluation of the radiation situation in nuclear power plants. 3. Equipment for monitoring the nuclear power plant and its environs. 4. Mathematical modelling and assessment of the nuclear power plant radiation environmental impact. 5. Evaluation of sources and of the transport of radioactive materials inside the power plant and the minimization of the nuclear power plant's environmental impact. (Z.M.)

A hypersonic lift mechanism with decoupled lift and drag surfaces

Science.gov (United States)

Xu, YiZhe; Xu, ZhiQi; Li, ShaoGuang; Li, Juan; Bai, ChenYuan; Wu, ZiNiu

2013-05-01

In the present study, we propose a novel lift mechanism for which the lifting surface produces only lift. This is achieved by mounting a two-dimensional shock-shock interaction generator below the lifting surface. The shock-shock interaction theory in conjunction with a three dimensional correction and checked with computational fluid dynamics (CFD) is used to analyze the lift and drag forces as function of the geometrical parameters and inflow Mach number. Through this study, though limited to only inviscid flow, we conclude that it is possible to obtain a high lift to drag ratio by suitably arranging the shock interaction generator.

International Conference on Power Electronics and Renewable Energy Systems

CERN Document Server

Suresh, L; Dash, Subhransu; Panigrahi, Bijaya

2015-01-01

The book is a collection of high-quality peer-reviewed research papers presented in Proceedings of International Conference on Power Electronics and Renewable Energy Systems (ICPERES 2014) held at Rajalakshmi Engineering College, Chennai, India. These research papers provide the latest developments in the broad area of Power Electronics and Renewable Energy. The book discusses wide variety of industrial, engineering and scientific applications of the emerging techniques. It presents invited papers from the inventors/originators of new applications and advanced technologies.

Fuel rod pressure in nuclear power reactors: Statistical evaluation of the fuel rod internal pressure in LWRs with application to lift-off probability

Energy Technology Data Exchange (ETDEWEB)

Jelinek, Tomas

2001-02-01

In this thesis, a methodology for quantifying the risk of exceeding the Lift-off limit in nuclear light water power reactors is outlined. Due to fission gas release, the pressure in the gap between the fuel pellets and the cladding increases with burnup of the fuel. An increase in the fuel-clad gap due to clad creep would be expected to result in positive feedback, in the form of higher fuel temperatures, leading to more fission gas release, higher rod pressure, etc, until the cladding breaks. An increase in the fuel-clad gap that leads to this positive feedback is a phenomenon called Lift-off and is a limitation that must be considered in the fuel core management. Lift-off is a consequence of very high internal fuel rod pressure. The internal fuel rod pressure is therefore used as a Lift-off indicator. The internal fuel rod pressure is closely connected to the fission gas release into the fuel rod plenum and is thus used to increase the database. It is concluded that the dominating error source in the prediction of the pressure in Boiling Water Reactors (BWR), is the power history. There is a bias in the fuel pressure prediction that is dependent on the fuel rod position in the fuel assembly for BWRs. A methodology to quantify the risk of the fuel rod internal pressure exceeding a certain limit is developed; the risk is dependent of the pressure prediction and the fuel rod position. The methodology is based on statistical treatment of the discrepancies between predicted and measured fuel rod internal pressures. Finally, a methodology to estimate the Lift-off probability of the whole core is outlined.

A practical concept for powered or tethered weight-lifting LTA vehicles

Science.gov (United States)

Balleyguier, M. A.

1975-01-01

A concept for a multi-hull weightlifting airship is presented. The concept is based upon experience in the design and handling of gas-filled balloons for commercial purposes, it was first tested in April, 1972. In the flight test, two barrage balloons were joined side-by-side, with an intermediate frame, and launched in captive flight. The success of this flight test led to plans for a development program calling for a powered, piloted prototype, a follow-on 40 ton model, and a 400 ton transport model. All of these airships utilize a tetrehedric three-line tethering method for loading and unloading phases of flight, which bypasses many of the difficulties inherent in the handling of a conventional airship near the ground. Both initial and operating costs per ton of lift capability are significantly less for the subject design than for either helicopters or airships of conventional mono-hull design.

Normalized lift: an energy interpretation of the lift coefficient simplifies comparisons of the lifting ability of rotating and flapping surfaces.

Science.gov (United States)

Burgers, Phillip; Alexander, David E

2012-01-01

For a century, researchers have used the standard lift coefficient C(L) to evaluate the lift, L, generated by fixed wings over an area S against dynamic pressure, ½ρv(2), where v is the effective velocity of the wing. Because the lift coefficient was developed initially for fixed wings in steady flow, its application to other lifting systems requires either simplifying assumptions or complex adjustments as is the case for flapping wings and rotating cylinders.This paper interprets the standard lift coefficient of a fixed wing slightly differently, as the work exerted by the wing on the surrounding flow field (L/ρ·S), compared against the total kinetic energy required for generating said lift, ½v(2). This reinterpreted coefficient, the normalized lift, is derived from the work-energy theorem and compares the lifting capabilities of dissimilar lift systems on a similar energy footing. The normalized lift is the same as the standard lift coefficient for fixed wings, but differs for wings with more complex motions; it also accounts for such complex motions explicitly and without complex modifications or adjustments. We compare the normalized lift with the previously-reported values of lift coefficient for a rotating cylinder in Magnus effect, a bat during hovering and forward flight, and a hovering dipteran.The maximum standard lift coefficient for a fixed wing without flaps in steady flow is around 1.5, yet for a rotating cylinder it may exceed 9.0, a value that implies that a rotating cylinder generates nearly 6 times the maximum lift of a wing. The maximum normalized lift for a rotating cylinder is 1.5. We suggest that the normalized lift can be used to evaluate propellers, rotors, flapping wings of animals and micro air vehicles, and underwater thrust-generating fins in the same way the lift coefficient is currently used to evaluate fixed wings.

Variable Lifting Index (VLI): A New Method for Evaluating Variable Lifting Tasks.

Science.gov (United States)

Waters, Thomas; Occhipinti, Enrico; Colombini, Daniela; Alvarez-Casado, Enrique; Fox, Robert

2016-08-01

We seek to develop a new approach for analyzing the physical demands of highly variable lifting tasks through an adaptation of the Revised NIOSH (National Institute for Occupational Safety and Health) Lifting Equation (RNLE) into a Variable Lifting Index (VLI). There are many jobs that contain individual lifts that vary from lift to lift due to the task requirements. The NIOSH Lifting Equation is not suitable in its present form to analyze variable lifting tasks. In extending the prior work on the VLI, two procedures are presented to allow users to analyze variable lifting tasks. One approach involves the sampling of lifting tasks performed by a worker over a shift and the calculation of the Frequency Independent Lift Index (FILI) for each sampled lift and the aggregation of the FILI values into six categories. The Composite Lift Index (CLI) equation is used with lifting index (LI) category frequency data to calculate the VLI. The second approach employs a detailed systematic collection of lifting task data from production and/or organizational sources. The data are organized into simplified task parameter categories and further aggregated into six FILI categories, which also use the CLI equation to calculate the VLI. The two procedures will allow practitioners to systematically employ the VLI method to a variety of work situations where highly variable lifting tasks are performed. The scientific basis for the VLI procedure is similar to that for the CLI originally presented by NIOSH; however, the VLI method remains to be validated. The VLI method allows an analyst to assess highly variable manual lifting jobs in which the task characteristics vary from lift to lift during a shift. © 2015, Human Factors and Ergonomics Society.

77 FR 22312 - Geomagnetic Disturbances to the Bulk-Power System; Notice of Technical Conference

Science.gov (United States)

2012-04-13

...-Power System on Monday, April 30, 2012, from 11 a.m. to 4 p.m. This staff-led conference will be held in... webcast of the meeting/ conference is also available through www.ferc.gov . Anyone with Internet access...

NASA safety standard for lifting devices and equipment

Science.gov (United States)

1990-09-01

NASA's minimum safety requirements are established for the design, testing, inspection, maintenance, certification, and use of overhead and gantry cranes (including top running monorail, underhung, and jib cranes), mobile cranes, derrick hoists, and special hoist supported personnel lifting devices (these do not include elevators, ground supported personnel lifts, or powered platforms). Minimum requirements are also addressed for the testing, inspection, and use of Hydra-sets, hooks, and slings. Safety standards are thoroughly detailed.

Proceedings of the 2009 CIGRE Canada conference on power systems : innovation and renewal : building the new power system

International Nuclear Information System (INIS)

2009-01-01

The Conseil International des Grands Reseaux Electriques (CIGRE) is the International Council on Large Electric Systems. It promotes technical, economic and environmental developments in electricity transmission and generation. CIGRE Canada is the Canadian National Committee which fosters the participation of Canadian members in CIGRE activities. CIGRE Canada organizes an annual conference that provides a forum for power system engineers, decision makers,economists, and academics to discuss technological developments in electrical power systems. The presentations at this conference addressed issues regarding the use of renewable energy sources in power transmission and distribution systems, with particular reference to control and protection; HVDC and MVDC; modelling tools; interface technologies; and reduced carbon generation and sustainability. The use of active distribution systems was also discussed in terms of future trends; the role of information technology and communications; and the role of energy storage. The session on smart grids addressed issues such as power utility perspectives; sensing, measurements and controls; advanced interfaces and decision support systems; open-architecture; distributed energy resources; and regulatory issues. Issues concerning the interconnection of non traditional energy sources to the power systems were also discussed along with recent research initiatives related to renewable energy source development. The sessions were entitled: smart grids; distributed energy resources; wind and solar PV; AC systems and HV lines; wide area measurements; power system operation and control; modelling and analysis; substation automation; and HVDC and facts. The conference featured 66 presentations, of which 35 have been catalogued separately for inclusion in this database

12th Symposium on Space Nuclear Power and Propulsion. Conference on Alternative Power from Space (APFS),Conference on Accelerator-Driven Transmutation Technologies and Applications (A-DTTA)

International Nuclear Information System (INIS)

Mohamed, S.E.

1995-01-01

These proceedings represent papers presented at the 12th symposium on Space Nuclear Power and Propulsion held in Albuquerque, New Mexico. The symposium theme was ''commercialization and technology transfer''. The topics discussed include: wireless power transmission, solar power from space next generation spacecraft, space power electronics and power management, flight testing of components, manufacturing and processing of materials, nuclear propulsion, reactors and shielding and many others of interest to the scientific community representing industry, government and academic institutions. There were 163 papers presented at the conference and 60 have been abstracted for the Energy Science and Technology database

Normalized Lift: An Energy Interpretation of the Lift Coefficient Simplifies Comparisons of the Lifting Ability of Rotating and Flapping Surfaces

Science.gov (United States)

Burgers, Phillip; Alexander, David E.

2012-01-01

For a century, researchers have used the standard lift coefficient CL to evaluate the lift, L, generated by fixed wings over an area S against dynamic pressure, ½ρv 2, where v is the effective velocity of the wing. Because the lift coefficient was developed initially for fixed wings in steady flow, its application to other lifting systems requires either simplifying assumptions or complex adjustments as is the case for flapping wings and rotating cylinders. This paper interprets the standard lift coefficient of a fixed wing slightly differently, as the work exerted by the wing on the surrounding flow field (L/ρ·S), compared against the total kinetic energy required for generating said lift, ½v2. This reinterpreted coefficient, the normalized lift, is derived from the work-energy theorem and compares the lifting capabilities of dissimilar lift systems on a similar energy footing. The normalized lift is the same as the standard lift coefficient for fixed wings, but differs for wings with more complex motions; it also accounts for such complex motions explicitly and without complex modifications or adjustments. We compare the normalized lift with the previously-reported values of lift coefficient for a rotating cylinder in Magnus effect, a bat during hovering and forward flight, and a hovering dipteran. The maximum standard lift coefficient for a fixed wing without flaps in steady flow is around 1.5, yet for a rotating cylinder it may exceed 9.0, a value that implies that a rotating cylinder generates nearly 6 times the maximum lift of a wing. The maximum normalized lift for a rotating cylinder is 1.5. We suggest that the normalized lift can be used to evaluate propellers, rotors, flapping wings of animals and micro air vehicles, and underwater thrust-generating fins in the same way the lift coefficient is currently used to evaluate fixed wings. PMID:22629326

Normalized lift: an energy interpretation of the lift coefficient simplifies comparisons of the lifting ability of rotating and flapping surfaces.

Directory of Open Access Journals (Sweden)

Phillip Burgers

Full Text Available For a century, researchers have used the standard lift coefficient C(L to evaluate the lift, L, generated by fixed wings over an area S against dynamic pressure, ½ρv(2, where v is the effective velocity of the wing. Because the lift coefficient was developed initially for fixed wings in steady flow, its application to other lifting systems requires either simplifying assumptions or complex adjustments as is the case for flapping wings and rotating cylinders.This paper interprets the standard lift coefficient of a fixed wing slightly differently, as the work exerted by the wing on the surrounding flow field (L/ρ·S, compared against the total kinetic energy required for generating said lift, ½v(2. This reinterpreted coefficient, the normalized lift, is derived from the work-energy theorem and compares the lifting capabilities of dissimilar lift systems on a similar energy footing. The normalized lift is the same as the standard lift coefficient for fixed wings, but differs for wings with more complex motions; it also accounts for such complex motions explicitly and without complex modifications or adjustments. We compare the normalized lift with the previously-reported values of lift coefficient for a rotating cylinder in Magnus effect, a bat during hovering and forward flight, and a hovering dipteran.The maximum standard lift coefficient for a fixed wing without flaps in steady flow is around 1.5, yet for a rotating cylinder it may exceed 9.0, a value that implies that a rotating cylinder generates nearly 6 times the maximum lift of a wing. The maximum normalized lift for a rotating cylinder is 1.5. We suggest that the normalized lift can be used to evaluate propellers, rotors, flapping wings of animals and micro air vehicles, and underwater thrust-generating fins in the same way the lift coefficient is currently used to evaluate fixed wings.

PREFACE: The 15th International Conference on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2015)

Science.gov (United States)

Livermore, C.; Velásquez-García, L. F.

2015-12-01

Greetings, and welcome to Boston, MA and PowerMEMS 2015 - the 15th International Conference on Micro and Nanotechnology for Power Generation and Energy Conversion Applications! The objective of PowerMEMS 2015 is to catalyze innovation in micro- and nano-scale technologies for the energy domain. The scope of the meeting ranges from basic principles, to materials and fabrication, to devices and systems, to applications. The many applications of Power MEMS range from the harvesting, storage, conversion and conditioning of energy, to integrated systems that manage these processes, to actuation, pumping, and propulsion. Our Conference aims to stimulate the exchange of insights and information, as well as the development of new ideas, in the Power MEMS field. Our goal is to allow the attendees to interact and network within our multidisciplinary community that includes professionals from many branches of science and engineering, as well as energy, policy, and entrepreneurial specialists interested in the commercialization of Power MEMS technologies. Since the first PowerMEMS in Sendai, Japan in 2000, the Conference has grown in size, reputation, impact, and technical breadth. This continuing growth is evident in this year's technical program, which includes an increasing number of papers on nanomaterials, additive manufacturing for energy systems, actuators, energy storage, harvesting strategies and integrated energy harvesting systems, for example. This year's technical program is highlighted by six plenary talks from prominent experts on piezoelectrics, robotic insects, thermoelectrics, photovoltaics, nanocomposite cathodes, and thermal energy conversion systems. The contributed program received a large number of abstract submissions this year, 169 in total. After careful review by the 34-member Technical Program Committee, a total of 135 papers were selected for presentation. The 60 contributed oral presentations are arranged in two parallel sessions. The 75 posters

American power conference: Proceedings. Volume 56-I

International Nuclear Information System (INIS)

Anon.

1994-01-01

The first volume of this conference contains papers on the following topics: (1) Controls, monitoring, and expert systems (Harnessing microprocessor revolution for a more competitive power industry; Plant control--Upgrades; Neural network applications); (2) Diversification and globalization (Electric utility diversification/globalization--Panel; Private power in developing countries); (3) Environment and clean air (Clean Air compliance costs; Site selection for power stations and related facilities; Electric utility trace substance emissions; Solid waste disposal and commercial use; Precipitators/fabric filters; and Effect of flow modifications on fisheries and water quality); (4) Generation--Fuel options ampersand equipment (Alternate fuels; Advances in fuel cells for electric power applications; Secondary containment and seismic requirements for petrochemical facilities; Clean coal technology demonstration; Advanced energy systems; Hydropower); (5) Nuclear operations ampersand options (Radioactive waste management and disposal; Off normal conditions; Advanced light water reactors--15 years after TMI; Structural dynamic analyses for nuclear power plants); (6) Retrofit, betterment, repowering ampersand maintenance (Project management; Improving competitiveness through process re-engineering; Central stations; Water and wastewater treatment); (7) System planning, operation ampersand demand maintenance (Transmission system access; Stability; Systems planning); (8) Transmission and distribution (Transformers; Relaying for system protection; Managing EMF effects); and (9) Education (Power engineering). 155 papers have been processed separately for inclusion on the data base

Third RAAN conference: RAAN as Support of Nuclear Power

International Nuclear Information System (INIS)

Popescu, Camillo

2004-01-01

The proceedings of the third RAAN conference, titled 'RAAN as Support of Nuclear Power', held in Drobeta Turnu-Severin, Romania on 6-7 Nov 2003, are structured on three sections covering the following issues: - Section 1. Energy and Environment (19 papers); - Section 2. Isotopic products (3 papers); - Section 3. Prospects of Nuclear Power development in Romania (17 papers). Nuclear power in Romania was initiated on the basis of CANDU reactor type technology, an option found able to fulfill the requirements for a sustainable economic development, to support the electric energy demand of the country and to ensure the population and environment protection. The construction of the Cernavoda NPP was heavily based on the Romanian industry participation and basic and applied nuclear research national resources. The experience acquired from Cernavoda NPP Unit 1 will be fruitfully used in construction of the Units 2-5 to be built. Lately Romania's economy recorded a significant grow what entailed a net increase in the energy demand. Analyses presented in this conference that take into account the classical energy resources of the country, on one hand, and the natural uranium deposits, the existing facilities as for instance those ensuring from domestic industry both heavy water and the nuclear fuel, on the other hand, argue that the sole viable alternative ensuring the sustainable economic development appears to be the nuclear power based on the experience already acquired through Cernavoda NPP operation

4th International Conference on Power Transmissions

CERN Document Server

2013-01-01

This books contains the Proceedings of the 4th International Conference on Power Transmissions, that was held in Sinaia, Romania from June 20 -23, 2012. Power Transmissions is a very complex and multi-disciplinary scientific field of Mechanical Engineering that covers the different types of transmissions (mechanical, hydraulic, pneumatic) as well as all the machine elements involved, such as gears, bearings, shafts, couplings and a lot more. It concerns not only their basic theory but also their design, analysis, testing, application and maintenance. The requirements set to modern power transmissions are really tough to meet: They need to be more efficient, stronger, smaller, noiseless, easier to produce and to cost less. There is a strong demand to become easier in operation and maintenance, or even automatic and in maintenance-free. Last but not least, they should be easily recycled and respect the environment. Joint efforts of specialists from both academia and industry can significantly contribute to fulf...

A Real-Time Lift Detection Strategy for a Hip Exoskeleton.

Science.gov (United States)

Chen, Baojun; Grazi, Lorenzo; Lanotte, Francesco; Vitiello, Nicola; Crea, Simona

2018-01-01

Repetitive lifting of heavy loads increases the risk of back pain and even lumbar vertebral injuries to workers. Active exoskeletons can help workers lift loads by providing power assistance, and therefore reduce the moment and force applied on L5/S1 joint of human body when performing lifting tasks. However, most existing active exoskeletons for lifting assistance are unable to automatically detect user's lift movement, which limits the wide application of active exoskeletons in factories. In this paper, we propose a simple but effective lift detection strategy for exoskeleton control. This strategy uses only exoskeleton integrated sensors, without any extra sensors to capture human motion intentions. This makes the lift detection system more practical for applications in manufacturing environments. Seven healthy subjects participated in this research. Three different sessions were carried out, two for training and one for testing the algorithm. In the two training sessions, subjects were asked to wear a hip exoskeleton, controlled in transparent mode, and perform repetitive lifting and a locomotion circuit; lifting was executed with different techniques. The collected data were used to train the lift detection model. In the testing session, the exoskeleton was controlled in order to deliver torque to assist the lifting action, based on the lift detection made by the trained algorithm. The across-subject average accuracy of lift detection during online test was 97.97 ± 1.39% with subject-dependent model. Offline, the algorithm was trained with data acquired from all subjects to verify its performance for subject-independent detection, and an accuracy of 97.48 ± 1.53% was achieved. In addition, timeliness of the algorithm was quantitatively evaluated and the time delay was exoskeleton in assisting subjects in performing load lifting tasks. These results validate the promise of applying the proposed lift detection strategy for exoskeleton control aiming at lift

The hybrid assistive limb (HAL) for Care Support successfully reduced lumbar load in repetitive lifting movements.

Science.gov (United States)

Miura, Kousei; Kadone, Hideki; Koda, Masao; Abe, Tetsuya; Kumagai, Hiroshi; Nagashima, Katsuya; Mataki, Kentaro; Fujii, Kengo; Noguchi, Hiroshi; Funayama, Toru; Kawamoto, Hiroaki; Sankai, Yoshiyuki; Yamazaki, Masashi

2018-05-03

Work-related low back pain is a serious socioeconomic problem. This study examined whether HAL for Care Support, which is a newly developed wearable robot, would decrease lumbar fatigue and improve lifting performance during repetitive lifting movements. Eighteen healthy volunteers (11 men, 7 women) performed repetitive stoop lifting movements of a cardboard box weighing 12 kg as many times as possible. The first lifting trial was executed without HAL for Care Support, and the second was with it. We evaluated the VAS of lumbar fatigue as the lumbar load and the number of lifts and the lifting time as lifting performance. Without HAL for Care Support, the mean VAS of lumbar fatigue, the number of lifts and lifting time were 68 mm, 60 and 230 s; with HAL for Care Support, they were 51 mm, 87 and 332 s, respectively. Both lifting performance measures were significantly improved by using HAL for Care Support (Fig. 2). A power analysis showed that there was sufficient statistical power for the VAS of lumbar fatigue (0.99), the number of lifts (0.92), and lifting time (0.93). All participants performed their repetitive lifting trials safely. There were no adverse events caused by using HAL for Care Support. In conclusion, the HAL for Care Support can decrease lumbar load and improve the lifting performance during repetitive stoop lifting movements in healthy adults. Copyright © 2018. Published by Elsevier Ltd.

Proceedings of the Canadian Institute's BC power conference : maximizing opportunities in the evolving electricity sector

International Nuclear Information System (INIS)

2004-01-01

This conference provided a forum for reviewing recent events and activities in British Columbia's electric power industry. Issues regarding energy supply, reliability, power generation, power distribution and power transmission were discussed along with the opportunities and challenges of developing renewable energy sources. Participants at the conference gained insight into strategies for determining the usefulness of an energy plan; assessing the prospects for new generation capacity; examining future whole sale markets; analyzing congestion problems; identifying import and export opportunities; planning for rate design and exploring the future supply on Vancouver Island. The possibilities for meeting the growing demand for electricity through an integrated electrical transmission system throughout the west coast, British Columbia, the Pacific Northwest and Alberta were examined along with financing structures and strategies of renewable energy projects. The role of regulators and their influence on electricity prices were also discussed. Resource planning guidelines were examined as well as other topics such as demand side management, energy conservation, the role of liquefied natural gas in power generation, and land use challenges for power generation. The conference featured 21 presentations, of which 7 have been catalogued separately for inclusion in this database. tabs, figs

Assessment of the first conference

Energy Technology Data Exchange (ETDEWEB)

Whitmann, W G

1964-08-15

Full text: (Professor Whitmann was Secretary-General of the 1955 Conference). The dramatic lifting of the Iron Curtain, which had for decades sealed off communication between East and West, was the outstanding feature of the first United Nations International Conference on the Peaceful Uses of Atomic Energy in 1955. Many scientists had doubted that a truly scientific meeting would be permitted by governments, and had predicted that science would be submerged by political propaganda. Could this United Nations initiative be a creative instrumentality toward realizing that 'Open World' which Niels Bohr advocated with such eloquence? The Conference fully lived up to Mr. Hammarskjold's hopes that it would inaugurate a new era in intercommunication. Participating scientists were enthusiastic over the opportunity for direct association and discussion in a professional atmosphere, without significant political intervention. To laymen everywhere, the knowledge that the world's scientific elite was exchanging information and ideas about nuclear energy, with the purpose of developing its potential benefits to mankind, was most heartening. Here was long-delayed evidence of international co-operation. Papers and seminars on pure science were, naturally enough, more in evidence than those on engineering applications, both because of the relative state of knowledge and because of reticence to disclose engineering 'know-how' to potential competitors. Furthermore, it is quite evident in retrospect that the prospects for economical nuclear power at an early date were over-estimated by the enthusiasts. Even so, the creation of a body of informed opinion was an essential step to stimulate further research, design and sound economic analysis for the eventual development of useful power from the atom. A most significant initiative of this Conference was the recruiting of an international group of scientists within the staff of the United Nations to plan, to guide and to operate the

Assessment of the first conference

International Nuclear Information System (INIS)

Whitmann, W.G.

1964-01-01

Full text: (Professor Whitmann was Secretary-General of the 1955 Conference). The dramatic lifting of the Iron Curtain, which had for decades sealed off communication between East and West, was the outstanding feature of the first United Nations International Conference on the Peaceful Uses of Atomic Energy in 1955. Many scientists had doubted that a truly scientific meeting would be permitted by governments, and had predicted that science would be submerged by political propaganda. Could this United Nations initiative be a creative instrumentality toward realizing that 'Open World' which Niels Bohr advocated with such eloquence? The Conference fully lived up to Mr. Hammarskjold's hopes that it would inaugurate a new era in intercommunication. Participating scientists were enthusiastic over the opportunity for direct association and discussion in a professional atmosphere, without significant political intervention. To laymen everywhere, the knowledge that the world's scientific elite was exchanging information and ideas about nuclear energy, with the purpose of developing its potential benefits to mankind, was most heartening. Here was long-delayed evidence of international co-operation. Papers and seminars on pure science were, naturally enough, more in evidence than those on engineering applications, both because of the relative state of knowledge and because of reticence to disclose engineering 'know-how' to potential competitors. Furthermore, it is quite evident in retrospect that the prospects for economical nuclear power at an early date were over-estimated by the enthusiasts. Even so, the creation of a body of informed opinion was an essential step to stimulate further research, design and sound economic analysis for the eventual development of useful power from the atom. A most significant initiative of this Conference was the recruiting of an international group of scientists within the staff of the United Nations to plan, to guide and to operate the

Body lift, drag and power are relatively higher in large-eared than in small-eared bat species.

Science.gov (United States)

Håkansson, Jonas; Jakobsen, Lasse; Hedenström, Anders; Johansson, L Christoffer

2017-10-01

Bats navigate the dark using echolocation. Echolocation is enhanced by external ears, but external ears increase the projected frontal area and reduce the streamlining of the animal. External ears are thus expected to compromise flight efficiency, but research suggests that very large ears may mitigate the cost by producing aerodynamic lift. Here we compare quantitative aerodynamic measures of flight efficiency of two bat species, one large-eared ( Plecotus auritus ) and one small-eared ( Glossophaga soricina ), flying freely in a wind tunnel. We find that the body drag of both species is higher than previously assumed and that the large-eared species has a higher body drag coefficient, but also produces relatively more ear/body lift than the small-eared species, in line with prior studies on model bats. The measured aerodynamic power of P. auritus was higher than predicted from the aerodynamic model, while the small-eared species aligned with predictions. The relatively higher power of the large-eared species results in lower optimal flight speeds and our findings support the notion of a trade-off between the acoustic benefits of large external ears and aerodynamic performance. The result of this trade-off would be the eco-morphological correlation in bat flight, with large-eared bats generally adopting slow-flight feeding strategies. © 2017 The Author(s).

Proceedings of the tenth International Scientific Conference on Control of Power Systems

International Nuclear Information System (INIS)

Janicek, F.; Eleschova, Z.

2012-01-01

The conference scope covers control of production, transmission and consumption of energy, design, diagnostics, implementation, economic and environmental impact of control and information systems used in power engineering.

Storage of spent fuel from power reactors. 2003 conference proceedings

International Nuclear Information System (INIS)

2003-01-01

An International Conference on Storage of Spent Fuel from Power Reactors was organized by the IAEA in co-operation with the OECD Nuclear Energy Agency. The conference gave an opportunity to exchange information on the state of the art and prospects of spent fuel storage, to discuss the worldwide situation and the major factors influencing the national policies in this field and to identify the most important directions that national efforts and international co-operation in this area should take. The conference confirmed that the primary spent fuel management solution for the next decades will be interim storage. While the next step can be reprocessing or disposal, all spent fuel or high level waste from reprocessing must sooner or later be disposed of. The duration of interim storage is now expected to be much longer than earlier projections (up to 100 years and beyond). The storage facilities will have to be designed for these longer storage times and also for receiving spent fuel from advanced fuel cycle practices (i.e. high burnup and MOX spent fuel). It was noted that the handling and storage of spent fuel is a mature technology and meets the stringent safety requirements applicable in the different countries. The changes in nuclear policy and philosophy across the world, and practical considerations, have made storage a real necessity in the nuclear power industry. Utilities, vendors and regulators alike are addressing this adequately. The IAEA wishes to express appreciation to all chairs and co-chairs as well as all authors for their presentations to the conference and papers included in these proceedings

Storage of spent fuel from power reactors. 2003 conference proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-10-01

An International Conference on Storage of Spent Fuel from Power Reactors was organized by the IAEA in co-operation with the OECD Nuclear Energy Agency. The conference gave an opportunity to exchange information on the state of the art and prospects of spent fuel storage, to discuss the worldwide situation and the major factors influencing the national policies in this field and to identify the most important directions that national efforts and international co-operation in this area should take. The conference confirmed that the primary spent fuel management solution for the next decades will be interim storage. While the next step can be reprocessing or disposal, all spent fuel or high level waste from reprocessing must sooner or later be disposed of. The duration of interim storage is now expected to be much longer than earlier projections (up to 100 years and beyond). The storage facilities will have to be designed for these longer storage times and also for receiving spent fuel from advanced fuel cycle practices (i.e. high burnup and MOX spent fuel). It was noted that the handling and storage of spent fuel is a mature technology and meets the stringent safety requirements applicable in the different countries. The changes in nuclear policy and philosophy across the world, and practical considerations, have made storage a real necessity in the nuclear power industry. Utilities, vendors and regulators alike are addressing this adequately. The IAEA wishes to express appreciation to all chairs and co-chairs as well as all authors for their presentations to the conference and papers included in these proceedings.

13th International conference on environmental degradation of materials in nuclear power systems

International Nuclear Information System (INIS)

2007-01-01

The 13th International Conference on Environmental Degradation of Materials in Nuclear Power Systems was held on August 19-23, 2007 in Whistler, British Columbia, Canada. More of a scientific meeting than a convention, this conference series is the premier nuclear industry corrosion meeting where the 225 registrations consisted of world experts of the field from utilities, engineering and service organizations, manufacturers, research establishments and universities gathered to listen to 144 technical papers on new work and to explore new insights into corrosion mechanisms in the many water cooled systems in nuclear power plants. Over 225 delegates attended the conference, over 144 technical papers were presented in the following sessions: IASCC; Waste; PWR Secondary; Ni-Base Welds; Operating Experience; Low Alloy Steels; Alloy 800 Steam Generator Tubing; Zirconium Alloys; Crack Growth; SCWR; PWR Primary; BWR SCC; Irradiation Effects; Flow Accelerated Corrosion; and, Nobel Metal

Safe lifting in patients with chronic low back pain : Comparing FCE lifting task and NIOSH lifting guideline

NARCIS (Netherlands)

Kuijer, Wietske; Dijkstra, Pieter U.; Brouwer, Sandra; Reneman, Michiel F.; Groothoff, Johan W.; Geertzen, Jan H. B.

2006-01-01

Introduction: Both the floor-to-waist lifting task of the Isernhagen Work Systems Functional Capacity Evaluation (IWS FCE) and recommended weight limit (RWL) of the NIOSH produce safe lifting weights and are used world-wide nowadays. It is unknown whether they produce similar safe lifting weights.

Research on the aerodynamic characteristics of a lift drag hybrid vertical axis wind turbine

Directory of Open Access Journals (Sweden)

Xiaojing Sun

2016-01-01

Full Text Available Compared with a drag-type vertical axis wind turbines, one of the greatest advantages for a lift-type vertical axis wind turbines is its higher power coefficient (Cp. However, the lift-type vertical axis wind turbines is not a self-starting turbine as its starting torque is very low. In order to combine the advantage of both the drag-type and the lift-type vertical axis wind turbines, a lift drag hybrid vertical axis wind turbines was designed in this article and its aerodynamics and starting performance was studied in detail with the aid of computational fluid dynamics simulations. Numerical results indicate that the power coefficient of this lift drag hybrid vertical axis wind turbines declines when the distance between its drag-type blades and the center of rotation of the turbine rotor increases, whereas its starting torque can be significantly improved. Studies also show that unlike the lift-type vertical axis wind turbines, this lift drag hybrid-type vertical axis wind turbines could be able to solve the problem of low start-up torque. However, the installation position of the drag blade is very important. If the drag blade is mounted very close to the spindle, the starting torque of the lift drag hybrid-type vertical axis wind turbines may not be improved at all. In addition, it has been found that the power coefficient of the studied vertical axis wind turbines is not as good as expected and possible reasons have been provided in this article after the pressure distribution along the surfaces of the airfoil-shaped blades of the hybrid turbine was analyzed.

Lifting index of the niosh lifting equation and low back pain

Directory of Open Access Journals (Sweden)

Eliana Remor Teixeira

2011-09-01

Full Text Available The purpose of this study is to assess the relationship of the Lifting Index obtained through the application of the NIOSH Lifting Equation and the incidence of low back pain among forty-eight workers involved in manual lifting tasks. It was applied the equation in eleven tasks and the workers were interviewed. The most unfavorable conditions presented themselves in the lifting destination. The variables that most contributed to the inadequate values of the Lifting Index were: the horizontal location, the lifting frequency and the vertical distance, beyond the high weight of the load. The incidence of low back pain in the last twelve months was 19%, whereas the incidence of work-related low back pain in the same period was 10%. In 72.7% of the tasks evaluated the Composite Lifting Index was more than three, which are considered as high ergonomic risk.

The nuclear power option. Proceedings of an international conference on the nuclear power option held in Vienna, 5-8 September 1994

International Nuclear Information System (INIS)

1995-01-01

At 11 sessions of the conference present status and different aspects of future nuclear power development were discussed. About 150 participants from 37 countries and 7 international organizations attended the conference. 57 papers were presented. A separate abstract was prepared for each of these papers. Refs, figs and tabs

The 13th International Conference on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2013)

Science.gov (United States)

Mitcheson, Paul; Beeby, Steve

2013-12-01

It is a pleasure to welcome you to The Royal Society in London and the 13th International Conference on Micro- and Nano-Technology for Power Generation and Energy Conversion Applications, or PowerMEMS 2013. The objective of PowerMEMS 2013 is to catalyse innovation in miniature, micro- and nano-scale technologies for power generation and energy conversion. The conference aims to stimulate the exchange of insights and information, and the development of new ideas in the Power MEMS/NEMS field as well as at the meso-scale. It will allow the attendees to interact and network within our multidisciplinary community that includes professionals from many branches of science and engineering. The technical program is led by four invited speakers covering inductive power transfer, chip scale power sources, thermal energy harvesting and implantable biofuel cells. We received 177 abstracts and following a careful reviewing process by the Technical Program Committee a total of 137 papers were selected for presentation. These have been organised into 16 oral sessions in two parallel streams and two poster sessions that have been augmented by 10 late news papers. The oral and regular poster papers are, for the first time, being published by the Institute of Physics. We have made every effort to make PowerMEMS 2013 the busiest yet and have included for the first time the PowerMEMS School. This two-day school held at Imperial College London covered a wide range of power-MEMS topics including technologies for power generation, power transmission, energy storage, power electronics interfaces and metrology. Registrations for the School exceeded our expectations and it was full by early November. We hope this, and other activities such as the Discussion Panel and the inclusion of late news papers, will make PowerMEMS 2013 a memorable success. We have also reached out to new communities, such as those working in wireless power transfer and RF harvesting to broaden the technology remit of

CFD Study of an Annular-Ducted Fan Lift System for VTOL Aircraft

Directory of Open Access Journals (Sweden)

Yun Jiang

2015-09-01

Full Text Available The present study aimed at assessing a novel annular-ducted fan lift system for VTOL aircraft through computational fluid dynamics (CFD simulations. The power and lift efficiency of the lift fan system in hover mode, the lift and drag in transition mode, the drag and flight speed of the aircraft in cruise mode and the pneumatic coupling of the tip turbine and jet exhaust were studied. The results show that the annular-ducted fan lift system can have higher lift efficiency compared to the rotor of the Apache helicopter; the smooth transition from vertical takeoff to cruise flight needs some extra forward thrust to overcome a low peak of drag; the aircraft with the lift fan system enclosed during cruise flight theoretically may fly faster than helicopters and tiltrotors based on aerodynamic drag prediction, due to the elimination of rotor drag and compressibility effects on the rotor blade tips; and pneumatic coupling of the tip turbine and jet exhaust of a 300 m/s velocity can provide enough moment to spin the lift fan. The CFD results provide insight for future experimental study of the annular-ducted lift fan VTOL aircraft.

Proceedings of APPrO 2005, the 17. annual Canadian power conference and trade show : making the pieces fit

International Nuclear Information System (INIS)

Brooks, J.

2006-01-01

The Canadian power conference and trade show is one of the leading conferences in the Ontario electricity sector. It examines how Ontario plans to build or replace power capacity following a path for new generation, based on both renewable and conventional sources. The current implementation of new generation and prospects for future expansion were discussed along with supply and demand issues. Topics of discussion focused on the Ontario electricity market and what is perceived by industry representatives to be the elements that need to be improved. The best structure for the industry and the degree of government involvement to meet future demand was discussed. The green power conference, which was run concurrently with this event, focused on renewable energy sources and zero greenhouse gas emission technologies. Eight sessions from the conference were indexed separately for inclusion in this database. tabs., figs

The Exergy of Lift and Aircraft Exergy Flow Diagrams

OpenAIRE

Paulus, Jr., David; Gaggioli, Richard

2010-01-01

Aside from incidental, auxiliary loads, in level flight the principal load on the aircraft propulsion engine is the power required to provide the continuous lift. To construct an exergy flow diagram for an aircraft – for example, for the purpose of pinpointing inefficiencies and for costing – an expression is needed for the exergy delivered to and by the wings. That is, an expression is needed for the exergy of lift. The purpose of this paper is to present an expression de...

Nuclear Power Remains Important Energy Option for Many Countries, IAEA Ministerial Conference Concludes

International Nuclear Information System (INIS)

2013-01-01

Full text: Nuclear power remains an important option for many countries to improve energy security, provide energy for development and fight climate change, the International Ministerial Conference on Nuclear Power in the 21st Century concluded today. Participants also emphasised the importance of nuclear safety in the future growth of nuclear power, noting that nuclear safety has been strengthened worldwide following the March 2011 accident at TEPCO's Fukushima Daiichi Nuclear Power Station. The Conference was organised by the International Atomic Energy Agency (IAEA) in cooperation with the Nuclear Energy Agency (NEA) of the Organisation for Economic Co-operation and Development (OECD), and hosted by the Government of the Russian Federation through the State Atomic Energy Corporation ROSATOM. Sergei Kirienko, Director General of the State Atomic Energy Corporation ROSATOM, said: ''The Conference has achieved its main goal: to confirm that nuclear energy is an important part of the world's energy-mix. The innovative character of this type of energy provides us with sustainable development in the future. The closed nuclear fuel cycle and fusion may open for humanity absolutely new horizons. The Conference underlined the leading role of the IAEA in promoting the peaceful use of nuclear power and provision of the non-proliferation regime. Russia as a co-founder of the IAEA will always support its efforts to develop and expand safety and security standards all over the world.'' ''I believe we can look ahead with confidence and optimism to the future of nuclear power in the 21st century,'' said IAEA Director General Yukiya Amano. After the accident at the Fukushima Daiichi Nuclear Power Plant in Japan in March 2011, ''effective steps have been taken to make nuclear power plants safer everywhere,'' he stressed. ''Nuclear power will make a significant and growing contribution to sustainable development in the coming decades. The IAEA is committed to ensuring that the

Obstacles to hydroelectric power. VDI conference on chances of hydroelectric power - conservation and environmental protection in conflict

International Nuclear Information System (INIS)

Sauer, H.D.

1994-01-01

Hydroelectric power is one of the most efficient energy sources and presents no CO 2 pollution problem, but there are obstacles as was shown at a VDI conference. Regional landscape conservation interests are in conflict with global environmental protection considerations. (orig.) [de

Comparative Kinematic Analysis of the Snatch Lifts in Elite Male Adolescent Weightlifters

Directory of Open Access Journals (Sweden)

Erbil Harbili

2014-06-01

Full Text Available The purpose of the study was to compare the linear kinematics of the barbell and the angular kinematics of the lower limb during the snatch lifts of two different barbell weights in elite male adolescent weightlifters. In the national team level, nine elite male adolescent weightlifters participated in the study. The snatch lifts were recorded by two video cameras under competitive conditions in preparation period before the European Junior Championship (Sony MiniDv PAL- 50 field/s and the two heaviest successful lifts were selected for kinematic analysis. The little toe, ankle, knee, hip, and shoulder on the body and one point on the barbell were digitized using Ariel Performance Analysis System (APAS, San Diego, CA, USA. Significant decreases were found in the maximum barbell height, the relative power output during the second pull, and the maximum vertical velocity of the barbell during the second pull of the heaviest lift (p < 0.05. Maximum extension velocity of the hip joint significantly increased during the first pull of the heaviest lift (p < 0.05. As the mass of the barbell increased, the maximum vertical velocity and the maximum height of the barbell and relative power output during the second pull decreased in the heaviest lift performed by adolescent weightlifters. Coaches should pay attention to assistant exercises to increase explosive strength during the second pull with maximum strength in male adolescent weightlifters.

On the Estimation of Time Dependent Lift of a European Starling (Sturnus vulgaris during Flapping Flight.

Directory of Open Access Journals (Sweden)

Oksana Stalnov

Full Text Available We study the role of unsteady lift in the context of flapping wing bird flight. Both aerodynamicists and biologists have attempted to address this subject, yet it seems that the contribution of unsteady lift still holds many open questions. The current study deals with the estimation of unsteady aerodynamic forces on a freely flying bird through analysis of wingbeat kinematics and near wake flow measurements using time resolved particle image velocimetry. The aerodynamic forces are obtained through two approaches, the unsteady thin airfoil theory and using the momentum equation for viscous flows. The unsteady lift is comprised of circulatory and non-circulatory components. Both approaches are presented over the duration of wingbeat cycles. Using long-time sampling data, several wingbeat cycles have been analyzed in order to cover both the downstroke and upstroke phases. It appears that the unsteady lift varies over the wingbeat cycle emphasizing its contribution to the total lift and its role in power estimations. It is suggested that the circulatory lift component cannot assumed to be negligible and should be considered when estimating lift or power of birds in flapping motion.

On the Estimation of Time Dependent Lift of a European Starling (Sturnus vulgaris) during Flapping Flight.

Science.gov (United States)

Stalnov, Oksana; Ben-Gida, Hadar; Kirchhefer, Adam J; Guglielmo, Christopher G; Kopp, Gregory A; Liberzon, Alexander; Gurka, Roi

2015-01-01

We study the role of unsteady lift in the context of flapping wing bird flight. Both aerodynamicists and biologists have attempted to address this subject, yet it seems that the contribution of unsteady lift still holds many open questions. The current study deals with the estimation of unsteady aerodynamic forces on a freely flying bird through analysis of wingbeat kinematics and near wake flow measurements using time resolved particle image velocimetry. The aerodynamic forces are obtained through two approaches, the unsteady thin airfoil theory and using the momentum equation for viscous flows. The unsteady lift is comprised of circulatory and non-circulatory components. Both approaches are presented over the duration of wingbeat cycles. Using long-time sampling data, several wingbeat cycles have been analyzed in order to cover both the downstroke and upstroke phases. It appears that the unsteady lift varies over the wingbeat cycle emphasizing its contribution to the total lift and its role in power estimations. It is suggested that the circulatory lift component cannot assumed to be negligible and should be considered when estimating lift or power of birds in flapping motion.

4-th EPRI International conference on the water chemistry of the organic-fuel thermal power plants

International Nuclear Information System (INIS)

Petrova, T.I.; Martynova, O.I.

1995-01-01

Most actual problems on thermal power engineering are discussed at EPRI conferences on organic fuel, conducted every two years. Experience in realization of economically beneficial, ecologically feasible modes and their monitoring, accumulated in recent years, was formulated at the 4-th conference with wide participation

16th International Conference on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2016)

International Nuclear Information System (INIS)

2016-01-01

It is our great pleasure to welcome you to PowerMEMS’16 - the 16th International Conference on Micro- and Nano-Technology for Power Generation and Energy Conversion Applications - in Paris at the UIC Espace Congrès, a few meters away from the Eiffel Tower. The objective of the PowerMEMS conference is to catalyse innovation in micro- and nano- scale technologies for the energy domain. The scope of the meeting ranges from basic principles, to materials and fabrication, to devices and systems, to applications. The many applications of Power MEMS concern the harvesting, storage, conversion and conditioning of energy, to integrated systems that manage these processes, to actuation, pumping, and propulsion. Our Conference aims to stimulate the exchange of insights and information, as well as the development of new ideas, in the Power MEMS field. Our goal is to allow the attendees to interact and network within our multidisciplinary community that includes professionals from many branches of science and engineering, as well as energy, policy, and entrepreneurial specialists interested in the commercialization of Power MEMS technologies. This year's technical program is highlighted by four plenary talks from prominent experts on M/NEMS for ultra-low power in electronics, advanced nanomaterial for solar cells and thermal transistor. The contributed program received 159 abstract submissions this year. After careful review by the 33-members of the Technical Program Committee, a total of 123 papers will be presented. The 40 contributed oral presentations are arranged in two parallel sessions. The 83 posters are arranged in a ''two-in-one'' poster session in which the poster session time is divided in two; half the posters will be presented during each half-session, allowing the poster presenters to also browse the posters during the poster session. Posters will remain up during the meeting, so please feel free to peruse them at your leisure. The

2nd European Conference on Green Power Marketing 2002

International Nuclear Information System (INIS)

2002-01-01

This report summarises the information presented at the European Conference on Green Power Marketing held in 2002 in St. Moritz, Switzerland. It takes a look at the market chances of ecologically produced electricity for use in Switzerland and for export. The opinions of experts from the areas of research, business, politics, marketing and non-governmental organisations that were presented at the meeting are summarised. International perspectives and trends are discussed and strategies and management issues are examined. Product and price policies are discussed, as are instruments for the communication of 'Green Power' issues. Also, issues concerning customer needs, renewable energy sources, climate change and sustainability are dealt with and the situation in Australia is looked at

Proceedings of the international conference on nuclear power plant aging, availability factor and reliability analysis

International Nuclear Information System (INIS)

Goel, V.S.

1985-01-01

This book presents the papers given at a conference on nuclear power plant life extension. Topics considered at the conference included availability, accelerated aging techniques, the qualification of electrical equipment, probabilistic risk assessment, reactor maintenance, outages, reliability, computer-aided design, seismic effects, mechanical vibrations, fatigue monitoring, steam generators, and materials degradation by aging and embrittlement

Proceedings of the buying and pricing power in Alberta 2001 conference : making informed decisions

International Nuclear Information System (INIS)

2001-01-01

The changing landscape of energy pricing and buying in Alberta provided the impetus for this conference, where a wide range of topics were covered. The presenters reflected on the importance of having comprehensive information in order to make a decision in this field. The eleven speakers represented power distribution companies and discussed: the new challenges in buying and selling power in Alberta; the evolving electricity market managing and energy portfolio; pricing of power in the new market; the impact on industrial/commercial customers; allocation of risk in power purchase agreements; paying for the transmission system; marketing under the changing rules of the game; forward markets in Alberta; new product and service offerings; alternatives to the grid: distributed generation, energy strategies; uncertainty and opportunity in Alberta's deregulated market, load allocation and financial settlement. The conference was an opportunity for all interested parties to exchange views and ideas pertaining to the marketing and the pricing of energy in Alberta. refs., tabs., figs

Conference on renewable energies integration to power grids

International Nuclear Information System (INIS)

Laffaille, Didier; Bischoff, Torsten; Merkel, Marcus; Rohrig, Kurt; Glatigny, Alain; Quitmann, Eckard; Lehec, Guillaume; Teirlynck, Thierry; Stahl, Oliver

2014-01-01

The French-German office for Renewable energies (OFAEnR) organised a conference on renewable energies integration to power grids. In the framework of this French-German exchange of experience, more than 150 participants exchanged views on the perspectives and possible solutions of this integration in order to warrant the security of supplies and the grid stability in a context of increasing injection and decentralization of renewable power sources. This document brings together the available presentations (slides) made during this event: 1 - French distribution grids - Overview and perspectives (Didier Laffaille); 2 - Distribution Grids in Germany - Overview and Perspective (Torsten Bischoff); 3 - Integration of renewable energies into distribution grids - a case example from Germany (Marcus Merkel); 4 - Regeneratives Kombikraftwerk Deutschland: System Services with 100 % Renewable energies (Kurt Rohrig); 5 - Overview of the different grid instrumentation-control and automation tools (Alain Glatigny); 6 - Which Ancillary Services needs the Power System? The contribution from Wind Power Plants (Eckard Quitmann); 7 - The Flexibility Aggregator - the example of the GreenLys Project (Guillaume Lehec); 8 - Energy Pool - Providing flexibility to the electric system. Consumption cut-off solutions in France (Thierry Teirlynck); 9 - Demand Response experiences from Germany (Oliver Stahl)

Powering and Motion Predictions of High Speed Sea Lift (HSSL) Ships

National Research Council Canada - National Science Library

Gorski, Joseph; Miller, Ronald; Carrica, Pablo; Kandasamy, Mani; Stern, Fred

2007-01-01

High Speed Sea Lift (HSSL) is an important area of in terest for the US Navy. Computational tools are needed to predict the hydrodynamics of these configurations for their proper design and analysis in many areas including...

Normalized Lift: An Energy Interpretation of the Lift Coefficient Simplifies Comparisons of the Lifting Ability of Rotating and Flapping Surfaces

OpenAIRE

Burgers, Phillip; Alexander, David E.

2012-01-01

For a century, researchers have used the standard lift coefficient C(L) to evaluate the lift, L, generated by fixed wings over an area S against dynamic pressure, ½ρv(2), where v is the effective velocity of the wing. Because the lift coefficient was developed initially for fixed wings in steady flow, its application to other lifting systems requires either simplifying assumptions or complex adjustments as is the case for flapping wings and rotating cylinders.This paper interprets the standar...

3. national conference on training of personnel for nuclear power

International Nuclear Information System (INIS)

Jacko, J.

1983-01-01

A national conference with international participation was held in Podbanske to evaluate the results and experiences with the training of personnel for nuclear power in training centres of the sector of fuel and energy, within the educational system and at other workplaces. The rational development of the system of personnel training must contribute towards reducing the hazards of nuclear power caused by the human factor. The results and experiences were evaluated gained in the process of the unified system of training personnel for nuclear power plants, namely training centres of various institutions, institutions of higher education and in-operation training of personnel. In 1984, the first Czechoslovak simulator of a WWER 440 unit will be put into operation. (M.D.)

8th International Conference on Robotic, Vision, Signal Processing & Power Applications

CERN Document Server

Mustaffa, Mohd

2014-01-01

The proceeding is a collection of research papers presented, at the 8th International Conference on Robotics, Vision, Signal Processing and Power Applications (ROVISP 2013), by researchers, scientists, engineers, academicians as well as industrial professionals from all around the globe. The topics of interest are as follows but are not limited to: • Robotics, Control, Mechatronics and Automation • Vision, Image, and Signal Processing • Artificial Intelligence and Computer Applications • Electronic Design and Applications • Telecommunication Systems and Applications • Power System and Industrial Applications  

Proceedings of the American power conference: Volume 61-1

International Nuclear Information System (INIS)

McBride, A.E.

1999-01-01

This is volume one of the proceedings of the American Power Conference of 1999. The topics of the papers include multi-skilled work forces for the next century; global climate change and mitigation; distributed generation prospects in an open market; US DOE--EPRI wind turbine verification program; operations and maintenance cost reduction strategies; surviving deregulation and competition; power markets risk management and trading; interconnected operations; commercializing reliability; utility automation; electrical impacts of facilities operation; training for the future; SOX/PM2.5/air toxic; turbine-generator plant advances; codes and standards -- competing globally; business opportunities; the changing regulatory environment; advanced fuel design and engineering analysis: mandate for competing under regulation; unit commitment and dispatch; strategies for the open market; outage management; distribution reliability; and NOX control

Proceedings of the first MIT international conference on the next generation of nuclear power technology

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-07-01

The overall goal of advanced nuclear reactor development is to provide technological options which will be broadly acceptable to the different interested communities - electric utilities, environmental protection interests and electricity consumers. These constituencies will differ greatly in their priorities and understandings of what is feasible. However they all will collectively determine the definition of what constitutes an acceptable technology. The purpose of the Conference reported here was to aid the process reaching a greater consensus concerning acceptable technologies. The Conference was structured to permit all of those involved to gain a common understanding of the performance attributes which can reasonably be expected from the next generation of nuclear power plants, and to assist the process of communication among the various interest groups - ranging from reactor manufacturers and electric utilities to groups which have been strongly critical of nuclear power. This Conference is the first of an indefinite series of Conferences to be sponsored by the Program. The purpose of having a series of Conferences is to permit them to serve as a vehicle for sustained discussion among the communities which will determine whether future nuclear power plants are acceptable as national strategic options. The hope in organizing these Conferences is to improve the technologies which will eventually emerge, as a consequence of early effective communication among those concerned with the results. In order to do this, however, it is necessary for the people involved in such communication to have opportunities for sustained exposure to the ideas of others whom they would not otherwise have met. To do this it is necessary that these various communities interact repeatedly. The Conference series is intended to assist in that process. The Conference consisted of six focused topical sessions and two panel discussions. In each topical session keynote and respondent papers

Proceedings of the first MIT international conference on the next generation of nuclear power technology

International Nuclear Information System (INIS)

1990-01-01

The overall goal of advanced nuclear reactor development is to provide technological options which will be broadly acceptable to the different interested communities - electric utilities, environmental protection interests and electricity consumers. These constituencies will differ greatly in their priorities and understandings of what is feasible. However they all will collectively determine the definition of what constitutes an acceptable technology. The purpose of the Conference reported here was to aid the process reaching a greater consensus concerning acceptable technologies. The Conference was structured to permit all of those involved to gain a common understanding of the performance attributes which can reasonably be expected from the next generation of nuclear power plants, and to assist the process of communication among the various interest groups - ranging from reactor manufacturers and electric utilities to groups which have been strongly critical of nuclear power. This Conference is the first of an indefinite series of Conferences to be sponsored by the Program. The purpose of having a series of Conferences is to permit them to serve as a vehicle for sustained discussion among the communities which will determine whether future nuclear power plants are acceptable as national strategic options. The hope in organizing these Conferences is to improve the technologies which will eventually emerge, as a consequence of early effective communication among those concerned with the results. In order to do this, however, it is necessary for the people involved in such communication to have opportunities for sustained exposure to the ideas of others whom they would not otherwise have met. To do this it is necessary that these various communities interact repeatedly. The Conference series is intended to assist in that process. The Conference consisted of six focused topical sessions and two panel discussions. In each topical session keynote and respondent papers

Face-Lift

Science.gov (United States)

... or sun damage, you might also consider a skin-resurfacing procedure. A face-lift can be done in combination with some other cosmetic procedures, such as a brow lift or eyelid surgery. Why it's done As you get older, your facial skin changes — sagging and becoming loose. This can make ...

Lift-and-fill face lift: integrating the fat compartments.

Science.gov (United States)

Rohrich, Rod J; Ghavami, Ashkan; Constantine, Fadi C; Unger, Jacob; Mojallal, Ali

2014-06-01

Recent discovery of the numerous fat compartments of the face has improved our ability to more precisely restore facial volume while rejuvenating it through differential superficial musculoaponeurotic system treatment. Incorporation of selective fat compartment volume restoration along with superficial musculoaponeurotic system manipulation allows for improved control in recontouring while addressing one of the key problems in facial aging, namely, volume deflation. This theory was evaluated by assessing the contour changes from simultaneous face "lifting" and "filling" through fat compartment-guided facial fat transfer. A review of 100 face-lift patients was performed. All patients had an individualized component face lift with fat grafting to the nasolabial fold, deep malar, and high/lateral malar fat compartment locations. Photographic analysis using a computer program was conducted on oblique facial views preoperatively and postoperatively, to obtain the most projected malar contour point. Two independent observers visually evaluated the malar prominence and nasolabial fold improvements based on standardized photographs. Nasolabial fold improved by at least one grade in 81 percent and by over one grade in 11 percent. Malar prominence average projection increase was 13.47 percent and the average amount of lift was 12.24 percent. The malar prominence score improved by at least one grade in 62 percent of the patients postoperatively, and 9 percent had a greater than one grade improvement. Twenty-eight percent of the patients had a convex malar prominence postoperatively compared with 6 percent preoperatively. Malar prominence improved by at least one grade in 63 percent and by over one grade in 10 percent. The lift-and-fill face lift merges two key concepts in facial rejuvenation: (1) effective tissue manipulation by means of lifting and tightening in differential vectors according to original facial asymmetry and shape; and (2) selective fat compartment filling

Proceedings: 1987 conference on expert-system applications in power plants

International Nuclear Information System (INIS)

1988-12-01

The third EPRI conference on expert system applications for the electric utilities was held in Boston on May 27--29, 1987. The conference was co-hosted by Boston Edison Company and Niagara Mohawk Power Corporation and it was attended by more than 300 attendees from the US, Europe and Japan. The participants represented a broad spectrum of utilities, equipment manufacturers, engineering consultants, university faculty, and members of the federal and state regulatory agencies. Many applications of expert systems have emerged recently and many of the vendors now have meaningful prototypes that can demonstrate the benefits of expert systems to the utilities. Several utilities also have prototypes working at this time; but more importantly, the utilities have advanced significantly in their understanding and appreciation of this technology. Many utilities have organized teams within their organizations that have the charter of evaluating the leading applications and developing associated plans for the implementation of these applications. The conference identified several areas that are important to the utilities: training of the utility staff in the basic technology to rapidly build the appropriate infrastructure; review and recommendations in selection of hardware and software tools. This is needed since there is a very rapid change both in the market place as well as in terms of technical progress; dissemination of examples of good applications that directly relate to the power industry would be very helpful in relating to how the technology can be used; and coordination of the development of expert system applications among the utilities. This is needed since expert system applications typically are expensive to develop, but also relatively easy to transfer from one utility to another

Beams '96. Proceedings of the 11th international conference on high power particle beams. Vol. I

International Nuclear Information System (INIS)

Jungwirth, K.; Ullschmied, J.

1996-01-01

The Proceedings contain the full texts of 60 orals and 243 poster papers presented at the Conference. The scientific programme of the conference covered the physics and technology of intense beams of charged particles, from basic experimental and theoretical problems of beam generation, transport and interaction with various media, up to beam and pulsed power applications in science and in industry. The breakdown of the papers by main topical groups is as follows: electron beams, beam-plasma systems, high-power microwaves (62), imploding liners, z-pinches, plasma foci (53), pulsed power technology and its applications (53), ion beams and ICF (41), industrial applications of electron and ion beams (36), radiation sources (23), diagnostics (14), and others (21). (J.U.)

Beams `96. Proceedings of the 11th international conference on high power particle beams. Vol. I

Energy Technology Data Exchange (ETDEWEB)

Jungwirth, K.; Ullschmied, J. [eds.

1997-12-31

The Proceedings contain the full texts of 60 orals and 243 poster papers presented at the Conference. The scientific programme of the conference covered the physics and technology of intense beams of charged particles, from basic experimental and theoretical problems of beam generation, transport and interaction with various media, up to beam and pulsed power applications in science and in industry. The breakdown of the papers by main topical groups is as follows: electron beams, beam-plasma systems, high-power microwaves (62), imploding liners, z-pinches, plasma foci (53), pulsed power technology and its applications (53), ion beams and ICF (41), industrial applications of electron and ion beams (36), radiation sources (23), diagnostics (14), and others (21). (J.U.).

Lifting devices with minimum effort for testing, maintenance and repair at the example of a lifting rig for core internals

Energy Technology Data Exchange (ETDEWEB)

Pache, Martin [Westinghouse Electric Germany GmbH (Germany); Wiesendanger, Robert [Kernkraftwerk Beznau, NOK (Switzerland)

2008-07-01

Beznau is a Westinghouse built nuclear power plant in the Aargau area Switzerland. It consists of two PWR units, each providing 365 MWe net capacity. The units were set into operation in 1969 and 1972, respectively, and hold an unlimited license for operation, provided they continue to fulfill current legal and security requirements. Beznau's previous lifting rigs for core internals required a high effort in testing and maintenance. Moreover, a damage to one of the rigs nearly resulted in the inoperability of the rig. However, no element of the load chain was affected, so there was no danger of a crash, but it could have caused an extended outage. Hence, it was decided to replace the lifting rigs with a state-of-the-art functional design that reflects modern requirements on maintenance and testing. Although the plant was built to ASME standards and codes, the new lifting rigs have been designed to German KTA code for lifting devices (KTA 3902 / 3903 for equipment with increased requirements, as per section 4.3 of KTA 3902). Given KTA's demands on periodic testing, one main requirement on the new design was to minimize the testing effort for the new rigs. (orig.)

Proceedings of the APPrO 2008 20. annual conference and trade show : 20/20 vision : building tomorrow's power system today

International Nuclear Information System (INIS)

Brooks, J.

2009-01-01

This conference provided a forum for members of the Association of Power Producers of Ontario (APPrO) to discuss new technologies and developments in the management of electric power facilities. Demands for electricity continue to increase despite growing concerns about the level of greenhouse gas (GHG) emissions created by the electric power industry. The focus of this conference was on the development of a sustainable electric power industry designed to meet future integration plans for renewable energy sources while conforming with emerging carbon markets. Procurement policies and regulations were reviewed. Challenges and solutions for gas-fired power generation were discussed, and issues related to Ontario's nuclear energy industry were examined. Transmission system planning strategies were presented. Future directions for the growth of the power industry were reviewed. Global industry perspectives were also presented. Human resources strategies were discussed. A total of 43 presentations were given at the conference. refs., tabs., figs

Fuel-conservative guidance system for powered-lift aircraft

Science.gov (United States)

Erzberger, H.; Mclean, J. D.

1979-01-01

A concept for automatic terminal area guidance, comprising two modes of operation, was developed and evaluated in flight tests. In the predictive mode, fuel efficient approach trajectories are synthesized in fast time. In the tracking mode, the synthesized trajectories are reconstructed and tracked automatically. An energy rate performance model derived from the lift, drag, and propulsion system characteristics of the aircraft is used in the synthesis algorithm. The method optimizes the trajectory for the initial aircraft position and wind and temperature profiles encountered during each landing approach. The design theory and the results of simulations and flight tests using the Augmentor Wing Jet STOL Research Aircraft are described.

Lift scheduling organization : Lift Concept for Lemminkainen

OpenAIRE

Mingalimov, Iurii

2015-01-01

The purpose of the work was to make a simple schedule for the main contractors and clients to check and control workflow connected with lifts. It gathers works with electricity, construction, engineering networks, installing equipment and commissioning works. The schedule was carried out during working on the building site Aino in Saint Petersburg in Lemminkӓinen. The duration of work was 5 months. The lift concept in Lemminkӓinen is very well controlled in comparison with other buil...

Lifting strength in two-person teamwork.

Science.gov (United States)

Lee, Tzu-Hsien

2016-01-01

This study examined the effects of lifting range, hand-to-toe distance, and lifting direction on single-person lifting strengths and two-person teamwork lifting strengths. Six healthy males and seven healthy females participated in this study. Two-person teamwork lifting strengths were examined in both strength-matched and strength-unmatched groups. Our results showed that lifting strength significantly decreased with increasing lifting range or hand-to-toe distance. However, lifting strengths were not affected by lifting direction. Teamwork lifting strength did not conform to the law of additivity for both strength-matched and strength-unmatched groups. In general, teamwork lifting strength was dictated by the weaker of the two members, implying that weaker members might be exposed to a higher potential danger in teamwork exertions. To avoid such overexertion in teamwork, members with significantly different strength ability should not be assigned to the same team.

Thread-Lift Sutures: Still in the Lift? A Systematic Review of the Literature.

Science.gov (United States)

Gülbitti, Haydar Aslan; Colebunders, Britt; Pirayesh, Ali; Bertossi, Dario; van der Lei, Berend

2018-03-01

In 2006, Villa et al. published a review article concerning the use of thread-lift sutures and concluded that the technique was still in its infancy but had great potential to become a useful and effective procedure for nonsurgical lifting of sagged facial tissues. As 11 years have passed, the authors now performed again a systematic review to determine the real scientific current state of the art on the use of thread-lift sutures. A systematic review was performed according to Preferred Reporting Items for Systematic Reviews and Meta-Analyses guidelines using the PubMed database and using the Medical Subject Headings search term "Rhytidoplasty." "Rhytidoplasty" and the following entry terms were included by this Medical Subject Headings term: "facelift," "facelifts," "face Lift," "Face Lifts," "Lift," "Face," "Lifts," "Platysmotomy," "Platysmotomies," "Rhytidectomy," "Rhytidectomies," "Platysmaplasty," "and "Platysmaplasties." The Medical Subject Headings term "Rhytidoplasty" was combined with the following search terms: "Barbed suture," "Thread lift," "APTOS," "Suture suspension," "Percutaneous," and "Silhouette suture." RefWorks was used to filter duplicates. Three of the authors (H.A.G., B.C., and B.L.) performed the search independently. The initial search with all search terms resulted in 188 articles. After filtering the duplicates and the articles about open procedures, a total of 41 articles remained. Of these, the review articles, case reports, and letters to the editor were subsequently excluded, as were reports dealing with nonbarbed sutures, such as Vicryl and Prolene with Gore-Tex. This resulted in a total of 12 articles, seven additional articles since the five articles reviewed by Villa et al. The authors' review demonstrated that, within the past decade, little or no substantial evidence has been added to the peer-reviewed literature to support or sustain the promising statement about thread-lift sutures as made by Villa et al. in 2006 in terms of

Papers of the 2. annual Canadian Institute conference on interjurisdictional power transactions

International Nuclear Information System (INIS)

2002-01-01

Leaders in the electric power industry from Canada and the United States attended this conference which focused on ways that Ontario's new competitive energy market can maximize its profits through interjurisdictional power transactions with the US northeast and midwest. Topics of discussion included how to target power sales to hotspots in the United States, how to avoid seams issues when wheeling power through jurisdictions, and how to monitor intertie capacity. Other issues were also addressed, including how to manage profits from the financial transmission rights structure, and tracking the latest developments in RTO creation in the United States and its potential impact on interjurisdictional power transactions. A total of 12 papers were presented, of which 4 were indexed separately for inclusion in the database. tabs., figs

POWER-GEN '90 conference papers: Volume 3 (Environmental trends and issues) and Volume 4 (Case histories - Non-utility power generation)

International Nuclear Information System (INIS)

Anon.

1990-01-01

This is book 2 of a collection of papers presented at the Third International Power Generation Industries Conference on December 4-6, 1990. The book contains Volume 3, Environmental Trends and Issues, and Volume 4, Case Histories - Non-utility Power Generation. The topics of the papers include environmental legislative and regulatory trends, acid rain compliance strategies and technologies, other global environmental concerns, gas fired systems, solid and waste fuels, despatching and wheeling, and strategies for purchasing non-utility power

Proceedings of the Canadian Wind Energy Association's 2009 wind matters conference : wind and power systems

International Nuclear Information System (INIS)

2009-01-01

This conference provided a forum for wind energy and electric power industry experts to discuss issues related to wind and power systems. An overview of wind integration studies and activities in Canada and the United States was provided. New tools and technologies for facilitating the integration of wind and improve market conditions for wind energy developers were presented. Methods of increasing wind penetration were evaluated, and technical issues related to wind interconnections throughout North America were reviewed. The conference was divided into the following 5 sessions: (1) experiences with wind integration, and lessons learned, (2) update on ongoing wind integration initiatives in Canada and the United States, (3) initiatives and tools to facilitate wind integration and market access, (4) developments in wind interconnection and grid codes, (5) wind energy and cold weather considerations, and (6) challenges to achieving the 20 per cent WindVision goal in Canada. The conference featured 21 presentations, of which 13 have been catalogued separately for inclusion in this database. refs., tabs., figs

Proceedings of the CERI 2002 electricity conference : getting a grip on power sector restructuring. CD-ROM ed.

International Nuclear Information System (INIS)

2002-01-01

Electric power restructuring in a global context was reviewed at this conference which examined how existing market structures can be improved to benefit all participants. Topics of discussion ranged from issues regarding future development of power generation and transmission, to developing trends, expectations and implications for consumers, power generators and energy service providers. The 7 sessions of the conference were entitled: (1) global lessons from restructuring, what works and what doesn't, (2) competition in electricity markets, (3) restructuring in Canada, (4) suggestions for power sector reform, (5) competition in future generation markets, (6) trading, financing and generation alternatives, and (7) transmission expansion. A total of 7 papers have been indexed separately for inclusion in the database. refs., tabs., figs

Flow Control Research at NASA Langley in Support of High-Lift Augmentation

Science.gov (United States)

Sellers, William L., III; Jones, Gregory S.; Moore, Mark D.

2002-01-01

The paper describes the efforts at NASA Langley to apply active and passive flow control techniques for improved high-lift systems, and advanced vehicle concepts utilizing powered high-lift techniques. The development of simplified high-lift systems utilizing active flow control is shown to provide significant weight and drag reduction benefits based on system studies. Active flow control that focuses on separation, and the development of advanced circulation control wings (CCW) utilizing unsteady excitation techniques will be discussed. The advanced CCW airfoils can provide multifunctional controls throughout the flight envelope. Computational and experimental data are shown to illustrate the benefits and issues with implementation of the technology.

Innovative designs and technologies of nuclear power. IV International scientific and technical conference. Book of abstracts

International Nuclear Information System (INIS)

2016-01-01

IV International scientific and technical conference “Innovative designs and technologies of nuclear power” has been organized and is conducted by JSC NIKIET with support from Rosatom State Corporation, the International Atomic Energy Agency, the Russian Academy of Sciences and the Nuclear Society of Russia. The conference topics include: innovative designs of nuclear facilities for various applications, nuclear fuel and new materials, closed fuel cycle technologies, SNF and RW management, technological answers to nonproliferation problems, small power reactors (stationary, transportable, floatable, propulsion, space), integrated codes of a new generation for safety analysis of nuclear power plants and fuel cycles, controlled fusion [ru

POWER-GEN '90 conference papers: Volume 7 (Fossil plant performance availability and improvement) and Volume 8 (Nuclear power issues)

International Nuclear Information System (INIS)

Anon.

1990-01-01

This is book 4 of papers presented at the Third International Exhibition and Conference for the Power Generation Industries, December 4-6, 1990. This book contains Volume 7, Fossil Plant Performance Availability and Improvement, and Volume 8, Nuclear Power Issues. The topics of the papers include computer applications in plant operations and maintenance, managing aging plants, plant improvements, plant operations and maintenance, the future of nuclear power, achieving cost effective plant operation, managing nuclear plant aging and license renewal, and the factors affecting a decision to build a new nuclear plant

Conference summaries

International Nuclear Information System (INIS)

1988-01-01

This volume contains conference summaries of the 28. annual conference of the Canadian Nuclear Association, and the 9. annual conference of the Canadian Nuclear Society. Topics of discussion include: power reactors; fuel cycles; nuclear power and public understanding; future trends; applications of nuclear technology; CANDU reactors; operational enhancements; design of small reactors; accident behaviour in fuel channels; fuel storage and waste management; reactor commissioning/decommissioning; nuclear safety experiments and modelling; the next generation reactors; advances in nuclear engineering education in Canada; safety of small reactors; current position and improvements of fuel channels; current issues in nuclear safety; and radiation applications - medical and industrial

The Effect of Lifting Speed on Cumulative and Peak Biomechanical Loading for Symmetric Lifting Tasks

Directory of Open Access Journals (Sweden)

Kasey O. Greenland

2013-06-01

Conclusion: Based on peak values, BCF is highest for fast speeds, but the BCF cumulative loading is highest for slow speeds, with the largest difference between fast and slow lifts. This may imply that a slow lifting speed is at least as hazardous as a fast lifting speed. It is important to consider the duration of lift when determining risks for back and shoulder injuries due to lifting and that peak values alone are likely not sufficient.

Scaling of lifting forces in relation to object size in whole body lifting

NARCIS (Netherlands)

Kingma, I.; van Dieen, J.H.; Toussaint, H.M.

2005-01-01

Subjects prepare for a whole body lifting movement by adjusting their posture and scaling their lifting forces to the expected object weight. The expectancy is based on visual and haptic size cues. This study aimed to find out whether lifting force overshoots related to object size cues disappear or

9th International Conference on Robotics, Vision, Signal Processing & Power Applications

CERN Document Server

Iqbal, Shahid; Teoh, Soo; Mustaffa, Mohd

2017-01-01

 The proceeding is a collection of research papers presented, at the 9th International Conference on Robotics, Vision, Signal Processing & Power Applications (ROVISP 2016), by researchers, scientists, engineers, academicians as well as industrial professionals from all around the globe to present their research results and development activities for oral or poster presentations. The topics of interest are as follows but are not limited to:   • Robotics, Control, Mechatronics and Automation • Vision, Image, and Signal Processing • Artificial Intelligence and Computer Applications • Electronic Design and Applications • Telecommunication Systems and Applications • Power System and Industrial Applications • Engineering Education.

Proceedings of an international ministerial conference on nuclear power for the 21st century

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-08-15

The aim of this conference was to analyse the current trend in world nuclear power development as a result of recent considerations by a number of Member States regarding the future use and benefits of nuclear power. It is widely recognized that global energy demand will rise substantially during this century. The increased industrialization and urbanization of developing countries will produce large increases in energy demand in regions that currently have a very low per capita energy use. This increasing demand for energy will need to be met in order to improve living standards for the less well provided half of the world's population and to reduce the economic imbalances between countries and regions. At the same time, the use of fossil fuel based energy is identified as a major cause of environmental damage. The release of greenhouse gases by burning fossil fuel in power stations and for transport is seen as a contributor to global warming. It is widely recognized that continued exploitation of fossil fuels and releases of carbon dioxide will need to be controlled. After a prolonged period of slow development of nuclear power, confined to only some countries of the world, it is now being recognized that nuclear energy has a potentially significant role to play in meeting the energy needs of the planet without damaging the environment. Developments in technology make the economics of nuclear power more attractive, and they may become even more so as fossil fuel prices continue to rise. For a widespread use of nuclear power, however, there remain concerns on the safety, security, waste and proliferation aspects. The global application of safety standards and appropriate security measures is required to ensure acceptable levels of protection. Effective control measures are required to ensure that non-proliferation commitments are honoured. Handling nuclear waste safely and securely is achievable, but continues to remain a public concern. The broad strategic

Insight conference reports : Ontario power summit : embrace the changes, face the challenges

International Nuclear Information System (INIS)

2002-01-01

The main focus of this conference was on the current changes within Ontario's electricity industry and what can be learned from the experience of other jurisdictions. Opinions regarding the switch to open competition in Ontario on May 1, 2002 have been extremely varied. It was noted that open competition generally brings down electricity prices and is beneficial in introducing innovations. Opponents of competition are quick to point out that both California and Alberta have experienced the opposite with open markets. The presentations described the factors that contributed to the creation of an open electricity market in Ontario with reference to the unsustainable electricity rates of the 1990s. Participants at the conference also expressed their views regarding future electricity prices, and presented suggestions of how power transmission, distribution and generation can be optimized while protecting the consumer. A total of 18 papers were presented at the conference, of which 4 were indexed separately for inclusion in the database. refs., tabs., figs

Papers of a Canadian Institute conference on profiting from new opportunities in Atlantic power : new rules, new players, new challenges

International Nuclear Information System (INIS)

2003-01-01

New opportunities for power generation in Atlantic Canada were presented at this conference with particular reference to the influence that electricity restructuring has had on power markets, energy supplies and trade. Topics of discussion included: the future of electricity deregulation; increasing power transmission and intertie capacity; an energy mix which includes natural gas, hydro, wind and cogeneration; energy policy and regulations of the new power market; and, buyer and seller experience in the new market. The conference featured 12 presentations, of which 6 have been indexed separately for inclusion in this database. refs., tabs., figs

Ukrainian Nuclear Society International Conference 'Strategy of the nuclear power development: The choice of Ukraine'

International Nuclear Information System (INIS)

Vishnevskij, I.N.; Trofimenko, A.P.

2001-01-01

Abstracts of the papers presented at the International Conference of the Ukrainian Nuclear Society 'Strategy of the nuclear power development'. The following problems are considered: present situation with the nuclear power and its safety; nuclear fuel cycle development; waste and spent nuclear fuel management; reactors' decommissioning issues; modernization of the NPP with WWER reactors; future reactors; economics of nuclear power; safety culture; legal and regulatory framework, state nuclear regulatory control; PR in nuclear power industry; staff training

Human Resource Development for Introducing and Expanding Nuclear Power Programmes. Summary of an International Conference

International Nuclear Information System (INIS)

2012-01-01

Currently, the world is witnessing a resurgence of interest in nuclear power. More than fifty Member States, with support from the IAEA, are considering the introduction of nuclear power, and human resource development is one of the crucial areas in terms of requests for support. The need for human resources in the nuclear sector is not only experienced by countries embarking on new nuclear power programmes, but also by countries with existing programmes that are considering expansion, as many current professionals are approaching retirement age and the number of newly trained staff is generally not sufficient to meet the potential demand. The IAEA conference on Human Resource Development for Introducing and Expanding Nuclear Power Programmes was held from 14 to 18 March 2010 in Abu Dhabi, hosted by the Government of the United Arab Emirates. This conference was organized to address work force issues faced by countries which are embarking on new nuclear power programmes, expanding current programmes or planning to supply nuclear technology to other countries. The situation is different for each country; some need to develop their own local expertise, while others need to scale up existing educational and training programmes to increase the number of professionals. The purpose of this conference was to bring together Member States to help formulate country specific policies on human resource development, education, training and knowledge management to help support each country's nuclear power programme. In addition, the IAEA can facilitate better use of other educational opportunities, including research reactors and development of training facilities. These proceedings highlight the key findings and recommendations of the meeting and the conclusions of the chairperson. All papers presented and discussed during the meeting are included on the attached CD-ROM. To access the papers, click on 'Index' on the CD-ROM.

Human Resource Development for Introducing and Expanding Nuclear Power Programmes. Summary of an International Conference

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-10-15

Currently, the world is witnessing a resurgence of interest in nuclear power. More than fifty Member States, with support from the IAEA, are considering the introduction of nuclear power, and human resource development is one of the crucial areas in terms of requests for support. The need for human resources in the nuclear sector is not only experienced by countries embarking on new nuclear power programmes, but also by countries with existing programmes that are considering expansion, as many current professionals are approaching retirement age and the number of newly trained staff is generally not sufficient to meet the potential demand. The IAEA conference on Human Resource Development for Introducing and Expanding Nuclear Power Programmes was held from 14 to 18 March 2010 in Abu Dhabi, hosted by the Government of the United Arab Emirates. This conference was organized to address work force issues faced by countries which are embarking on new nuclear power programmes, expanding current programmes or planning to supply nuclear technology to other countries. The situation is different for each country; some need to develop their own local expertise, while others need to scale up existing educational and training programmes to increase the number of professionals. The purpose of this conference was to bring together Member States to help formulate country specific policies on human resource development, education, training and knowledge management to help support each country's nuclear power programme. In addition, the IAEA can facilitate better use of other educational opportunities, including research reactors and development of training facilities. These proceedings highlight the key findings and recommendations of the meeting and the conclusions of the chairperson. All papers presented and discussed during the meeting are included on the attached CD-ROM. To access the papers, click on 'Index' on the CD-ROM.

New heavy-lift system under construction

Energy Technology Data Exchange (ETDEWEB)

2009-07-01

Heavy-lift availability is at a premium, and the market is eager for alternatives to meet the demand. An alternative heavy-lift solution from SeaMetric - which has two multi-purpose heavy-lift vessels under construction in China - will be available in the first quarter of 2011. The TML system is based on buoyancy and ballast tanks, with four lifting arms mounted on two identical vessels, each vessel measuring 140 x 40 x 10.75 metres. To perform a lift, one TML with lifting arms is positioned on each side of the object. Using seawater pumps, lift force is created by de ballasting the buoyancy tanks and at the same time ballasting the ballast tanks. (AG). tab., ills

5. annual clean coal technology conference: powering the next millennium. Volume 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-06-01

The Fifth Annual Clean Coal Technology Conference focuses on presenting strategies and approaches that will enable clean coal technologies to resolve the competing, interrelated demands for power, economic viability, and environmental constraints associated with the use of coal in the post-2000 era. The program addresses the dynamic changes that will result from utility competition and industry restructuring, and to the evolution of markets abroad. Current projections for electricity highlight the preferential role that electric power will have in accomplishing the long-range goals of most nations. Increase demands can be met by utilizing coal in technologies that achieve environmental goals while keeping the cost- per-unit of energy competitive. Results from projects in the DOE Clean Coal Technology Demonstration Program confirm that technology is the pathway to achieving these goals. The industry/government partnership, cemented over the past 10 years, is focused on moving the clean coal technologies into the domestic and international marketplaces. The Fifth Annual Clean Coal Technology Conference provides a forum to discuss these benchmark issues and the essential role and need for these technologies in the post-2000 era. This volume contains technical papers on: advanced coal process systems; advanced industrial systems; advanced cleanup systems; and advanced power generation systems. In addition, there are poster session abstracts. Selected papers from this proceedings have been processed for inclusion in the Energy Science and Technology database.

Monitoring system of hydraulic lifting device based on the fiber optic sensors

Science.gov (United States)

Fajkus, Marcel; Nedoma, Jan; Novak, Martin; Martinek, Radek; Vanus, Jan; Mec, Pavel; Vasinek, Vladimir

2017-10-01

This article deals with the description of the monitoring system of hydraulic lifting device based on the fiber-optic sensors. For minimize the financial costs of the proposed monitoring system, the power evaluation of measured signal has been chosen. The solution is based on an evaluation of the signal obtained using the single point optic fiber sensors with overlapping reflective spectra. For encapsulation of the sensors was used polydimethylsiloxane (PDMS) polymer. To obtain a information of loading is uses the action of deformation of the lifting device on the pair single point optic fiber sensors mounted on the lifting device of the tested car. According to the proposed algorithm is determined information of pressure with an accuracy of +/- 5 %. Verification of the proposed system was realized on the various types of the tested car with different loading. The original contribution of the paper is to verify the new low-cost system for monitoring the hydraulic lifting device based on the fiber-optic sensors.

2008 annual nuclear technology conference: opting out of the use of nuclear power. German special approach leads into a dead end of energy policy. Conference report

International Nuclear Information System (INIS)

Anon.

2008-01-01

The President of the Deutsches Atomforum, Dr. Walter Hohlefelder, emphasized in his opening address at the 2008 Annual Nuclear Technology Conference in Hamburg that the German special approach to nuclear power utilization led straight into a dead end of energy policy. ''The outcome is foreseeable: The ambitious German goals of carbon dioxide reduction are missed, the competitiveness of the country is jeopardized, dependency on foreign energy imports rises,'' Dr. Hohlefelder stated. In view of the growing challenges in energy policy Germany had no alternative but to reassess nuclear power. The only outcome of this reappraisal could be extension of the life of nuclear power plants currently in operation. This was necessary also in order to avoid an impending gap in German electricity supply, Dr. Hohlefelder added. He invited all stakeholders to join in an open, unbiased dialog. Dr. Hohlefelder openly criticized the continued ban on research into the development of new reactors. ''A policy of this kind, a policy which bans thinking, is unacceptable in a technology-oriented, industrialized nation such as Germany.'' Nuclear power technology as a high-tech area was a unique achievement which had contributed to the prosperity of the country. The Annual Nuclear Technology Conference, which was held for the 39th time this year, is one of the biggest specialized conferences in the nuclear field with an attendance, this year, of approximately 1300 participants from more than twenty nations. (orig.)

European Power Electronic conference in Aalborg, Denmark - 1000 participants discussing the future energy technologies

DEFF Research Database (Denmark)

Blaabjerg, Frede; Munk-Nielsen, Stig

2007-01-01

The European Power Electronics and Adjustable Speed Drives conference with technical sponsorship of IEEE Industrial Electronic Society has been held in Aalborg, Denmark, during the first days of September 2007 with an overwhelming success and participation. It was hosted by Aalborg University's I...

How Do Wings Generate Lift?

Indian Academy of Sciences (India)

ideas to get expressions for lift and moment that are remarkably accurate. The pressure ... ating a lift force, leads to a nose-up or nose-down moment also. .... venient to use for a fluid since we would like to deal with a flow .... energy to get lift?

Proceedings of the international conference on nuclear power competitiveness in the next two decades

International Nuclear Information System (INIS)

1996-01-01

The purpose of this conference is to analyse the different elements that can have an influence on the cost of generating nucleo- electricity. Besides the usual predominant factors as fuel supply, personnel and maintenance that enter in the costs of any electricity generating method, nuclear power generation suffers the extra burden of severe regulatory demands, high decommissioning and insurance costs and an adverse public opinion that can effect competitiveness. Countries that can keep the nuclear option open during this difficult period will be the leaders in the future, those that cannot survive will become hopelessly energy dependent. Almost one hundred contributions gathered in these volume, as a result of presentations at the conference from participants from 22 countries, will contribute to increase competitiveness of nuclear power generation and, if possible, develop new ideas to help solve the present crisis in the nuclear sector. refs., ills

Proceedings of the international conference on nuclear power competitiveness in the next two decades

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

The purpose of this conference is to analyse the different elements that can have an influence on the cost of generating nucleo- electricity. Besides the usual predominant factors as fuel supply, personnel and maintenance that enter in the costs of any electricity generating method, nuclear power generation suffers the extra burden of severe regulatory demands, high decommissioning and insurance costs and an adverse public opinion that can effect competitiveness. Countries that can keep the nuclear option open during this difficult period will be the leaders in the future, those that cannot survive will become hopelessly energy dependent. Almost one hundred contributions gathered in these volume, as a result of presentations at the conference from participants from 22 countries, will contribute to increase competitiveness of nuclear power generation and, if possible, develop new ideas to help solve the present crisis in the nuclear sector. refs., ills.

Proceedings of the 2. MIT international conference on the next generation of nuclear power technology. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-12-31

The goal of the conference was to try to attract a variety of points of view from well-informed people to debate issues concerning nuclear power. Hopefully from that process a better understanding of what one should be doing will emerge. In organizing the conference lessons learned from the previous one were applied. A continuous effort was made to see to it that the arguments for the alternatives to nuclear power were given abundant time for presentation. This is ultimately because nuclear power is going to have to compete with all of the energy technologies. Thus, in discussing energy strategy all of the alternatives must be considered in a reasonable fashion. The structure the conference used has seven sessions. The first six led up to the final session which was concerned with what the future nuclear power strategy should be. Each session focused upon a question concerning the future. None of these questions has a unique correct answer. Rather, topics are addressed where reasonable people can disagree. In order to state some of the important arguments for each session`s question, the combination of a keynote paper followed by a respondent was used. The respondent`s paper is not necessarily included to be a rebuttal to the keynote; but rather, it was recognized that two people will look at a complex question with different shadings. Through those two papers the intention was to get out the most important arguments affecting the question for the session. The purpose of the papers was to set the stage for about an hour of discussion. The real product of this conference was that discussion.

World nuclear power once again in the spotlight. Comments on the 13th Pacfic Basin Nuclear Conference

International Nuclear Information System (INIS)

Zang Mingchang; Ruan Keqiang

2004-01-01

This paper comments on The 13th Pacific Basin Nuclear Conference held in Shenzhen, China, on October 21/25, 2002 and summarizes some key papers presented in the Conference and viewpoints from their following discussions, which indicates that nuclear power in the world is once again in the spotlight. The Conference shows that in the coming 50 years the roadmap to develop nuclear energy would be divided into two stages: Near-Term Deployment by 2010-2015, some advanced designs were developed for Utilities; Generation IV Program, its overall goal is to identify and develop next-generation nuclear power systems that could be deployed over the next 30 years to help meet the world's energy needs throughout the 21st century. Some visions is the future, such as co-generation of electricity and space heating or desalination, and combination of Generation IV and so-called Hydrogen Economy-the use of hydrogen in vehicle transport to replace petroleum, were presented. As a primary energy source nuclear power is particularly well suited to hydrogen production, offering the almost unique position of large-scale hydrogen production with near-zero emissions. (authors)

The 9. European nuclear conference; La 9. conference nucleaire europeenne

Energy Technology Data Exchange (ETDEWEB)

Maurel, V.; Lewis, D.; Smirnov, V.P.; Gutierrez, J.E.; Paulin, Ph.; Markov, D.V.; Smirnov, A.V.; Polenok, V.S.; Horhoianu, G.; Olteanu, G.; Van der Schaaf, B.; Gavillet, D.; Lapena, J.; Ohms, C.; Roth, A.; Van Dyck, St.; Mardon, J.P.; Thomas, A.; Cipiere, M.F.; Faidy, C.; Hedin, F.; Delnondedieu, M.; Chassignole, B.; Doudet, L.; Dupond, O.; Kang, K.; Park, K.; Kim, K.; Ha, J.; Hoon-Seok, Jung; Yong-koo, Lee; Kwang-Ho, Kim; Seungwoo, Paek; Heui-Joo, Choi; Do-Hee, Ahn; Kwang-Rag, Kim; Minsoo, Lee; Sung-Paal, Yim; Hongsuk, Chung; Detroux, P.; Meessen, O.; Defloor, J.; Lars-Erik, Holm; Barescut, J.C.; Vacquier, B.; Laurier, D.; Caer, S.; Quesne, B.; Oudalova, A.; Geras' kin, St.; Dikarev, V.; Dikareva, N.; Chernonog, E.; Yang-Geun, Chung; Gab-Bock, Lee; Sun-Young, Bang; Yong-Sun, Lee; Bolognese-Milsztajn, T.; Frank, D.; Lacoste, V.; Pihet, P.; Lacronique, J.F.; Chauliac, C.; Verwaerde, D.; Pavageau, O.; Zaetta, A.; Varaine, F.; Warin, D.; Hudelot, J.P.; Bioux, Ph.; Klann, R.; Petruzzi, A.; D' auria, F.; Yung Kwon, Jin; Chul Jin, Chol; Mihalache, M.; Radu, V.; Pavelescu, M.; Schneidesch, Ch.R.; Jinzhao, Zhang; Dalleur, J.P.; Nuttin, A.; Meplan, O.; Wilson, J.; Perdu, F.; Campioni, G.; Mounier, C.; Sigrist, J.F.; Laine, Ch.; Broc, D.; Robbe, M.F.; Cariou, Y.; Seok-Kyun, Yoon; Win, Naing; Myung-Hyun, Kim; Kyung, Hee; Fridman, E.; Shwageraus, E.; Galperin, A.; Meplan, O.; Laulan, O.; Mechel-Sendis, F.; Belgaid, M.; Kadem, F.; Amokrane, A.; Hamidouche, T.; El-Khider, Si-Ahmed

2005-11-15

This issue gathers the abstracts of the papers presented at the ninth European nuclear conference (ENC-2005). The main part of the conference is split into 20 sessions. These sessions cover all technical aspects of nuclear power, from reactor design to waste management, without forgetting experimental and research reactors, reactor dismantling, economy, resources, safety, radioprotection and education issues. Perspectives of a nuclear renaissance are clearly visible in the world. This renaissance, mainly due to political, economical, societal and ecological factors, is fuelled by scientific and technical progress. This conference was the opportunity to present together these aspects of nuclear power and to analyze their mutual interactions.

Helicopter Toy and Lift Estimation

Science.gov (United States)

Shakerin, Said

2013-01-01

A $1 plastic helicopter toy (called a Wacky Whirler) can be used to demonstrate lift. Students can make basic measurements of the toy, use reasonable assumptions and, with the lift formula, estimate the lift, and verify that it is sufficient to overcome the toy's weight. (Contains 1 figure.)

Conference on the flexibilization of the electric power system

International Nuclear Information System (INIS)

Laure Kaelble; Lantrain, Aurore; Pienisch, Kerstin; Behrens, Uwe; Renaud, Arnaud; Bena, Michel; Levacher, Ralf; Broves, Antoine de; Langrock, Thomas; Bureau, Cedric

2015-01-01

The French-German office for Renewable energies (OFAEnR) organised a conference on the flexibilization of the electric power system in France and in Germany. In the framework of this French-German exchange of experience, about 100 participants discussed the different existing flexibility offers and shared information about the regulatory and economical context in both countries. This document brings together the available presentations (slides) made during this event: 1 - Flexibility in Germany: Status Quo and Perspectives (Laure Kaelble); 2 - Flexibility and French regulation (Aurore Lantrain); 3 - Virtual Power Plants: Contributions to flexibility? (Kerstin Pienisch); 4 - Wind power as player in the market for flexibility (Uwe Behrens); 5 - Energy storage potential in France - PEPS study for 2030 (Arnaud Renaud); 6 - More Flexibilities for TSOs to operate the electric System (Michel Bena); 7 - 'PolyenergyNet' project: how to flexibilize the low voltage grid by making it more autonomous (Ralf Levacher, in German); 8 - Promotion of industrial Demand Response through aggregation (Antoine de Broves); 9 - Using urban load: an economical model for companies? (Thomas Langrock); 10 - How to Involve All Consumers? ENGIe's Demand Side Management Offers (Cedric Bureau)

Lambda-Lifting in Quadratic Time

DEFF Research Database (Denmark)

Danvy, Olivier; Schultz, Ulrik Pagh

2002-01-01

Lambda-lifting is a program transformation that is used in compilers, partial evaluators, and program transformers. In this article, we show how to reduce its complexity from cubic time to quadratic time, and we present a flow-sensitive lambda-lifter that also works in quadratic time. Lambda-lifting...... that yields the cubic factor in the traditional formulation of lambda-lifting, which is due to Johnsson. This search is carried out by computing a transitive closure. To reduce the complexity of lambda-lifting, we partition the call graph of the source program into strongly connected components, based...... of lambda-lifting from O(n^3) to O(n^2) . where n is the size of the program. Since a lambda-lifter can output programs of size O(n^2), our algorithm is asympotically optimal....

Lambda-Lifting in Quadratic Time

DEFF Research Database (Denmark)

Danvy, Olivier; Schultz, Ulrik Pagh

2003-01-01

Lambda-lifting is a program transformation that is used in compilers, partial evaluators, and program transformers. In this article, we show how to reduce its complexity from cubic time to quadratic time, and we present a flow-sensitive lambda-lifter that also works in quadratic time. Lambda-lifting...... that yields the cubic factor in the traditional formulation of lambda-lifting, which is due to Johnsson. This search is carried out by computing a transitive closure. To reduce the complexity of lambda-lifting, we partition the call graph of the source program into strongly connected components, based...... of lambda-lifting from O(n^3) to O(n^2) . where n is the size of the program. Since a lambda-lifter can output programs of size O(n^2), our algorithm is asympotically optimal....

Lambda-Lifting in Quadratic Time

DEFF Research Database (Denmark)

Danvy, Olivier; Schultz, Ulrik Pagh

2004-01-01

Lambda-lifting is a program transformation that is used in compilers, partial evaluators, and program transformers. In this article, we show how to reduce its complexity from cubic time to quadratic time, and we present a flow-sensitive lambda-lifter that also works in quadratic time. Lambda-lifting...... that yields the cubic factor in the traditional formulation of lambda-lifting, which is due to Johnsson. This search is carried out by computing a transitive closure. To reduce the complexity of lambda-lifting, we partition the call graph of the source program into strongly connected components, based...... of lambda-lifting from O(n^3) to O(n^2) . where n is the size of the program. Since a lambda-lifter can output programs of size O(n^2), our algorithm is asympotically optimal....

Radio Frequency Power in Plasmas: 12th Topical Conference. Proceedings

International Nuclear Information System (INIS)

Ryan, P.M.; Intrator, T.

1997-01-01

The twelfth Topical Conference on Radio Frequency Power in Plasmas was held in April, 1997, in Georgia, USA under the sponsorship of Oak Ridge National Laboratory of the US Department of Energy, the University of Wisconsin, and the American Physical Society. A large part of the conference was devoted to the ion cyclotron range of frequencies. Radio frequency contributions to the creation and maintenance of transport barriers to both particle and heat flux received a lot of attention. In addition to plasma heating, the use of RF as a versatile tool to drive current, shape profiles and stabilize plasmas was also discussed. The RF systems designs for ITER, ICRF heating advances on helical devices were among the topics of interest, so were progress in ion cyclotron codes, advanced launchers and technology, RF startup, general wave theory and the application of RF plasmas to material processing. A total of 103 papers were presented and are included in these proceedings. Out of these, 54 have been abstracted for the Energy Science and Technology database

The new Toyota variable valve timing and lift system

Energy Technology Data Exchange (ETDEWEB)

Shimizu, K.; Fuwa, N.; Yoshihara, Y. [Toyota Motor Corporation (Japan); Hori, K. [Toyota Boshoku Corporation (Japan)

2007-07-01

A continuously variable valve timing (duration and phase) and lift system was developed. This system was applied to the valvetrain of a new 2.0L L4 engine (3ZRFAE) for the Japanese market. The system has rocker arms, which allow continuously variable timing and lift, situated between a conventional roller-rocker arm and the camshaft, an electromotor actuator to drive it and a phase mechanism for intake and exhaust camshafts (Dual VVT-i). The rocking center of the rocker arm is stationary, and the axial linear motion of a helical spline changes the initial phase of the rocker arm which varies the timing and lift. The linear motion mechanism uses an original planetary roller screw and is driven by a brushless motor with a built-in electric control unit. Since the rocking center and the linear motion helical spline center coincide, a compact cylinder head design was possible, and the cylinder head is a common design with a conventional engine. Since the ECU controls intake valve duration and timing, a fuel economy gain of maximum 10% (depending on driving condition) is obtained by reducing light to medium load pumping losses. Also intake efficiency was maximized throughout the speed range, resulting in a power gain of 10%. Further, HC emissions were reduced due to increased air speed at low valve lift. (orig.)

Buying and selling power in a deregulated energy market : proceedings of an Insight conference

International Nuclear Information System (INIS)

1999-01-01

Issues relating to the restructuring of Ontario's electric power industry, especially the buying and selling of power are the principal focus of this conference. The restructuring began in November 1997 when the Ontario government announced its plans to have open competition in both the wholesale and retail electricity market by the year 2000. The nature of buying and selling in a competitive energy market, the impact that this new regulatory regime will have on Municipal Electrical Utilities (MEUs), supplier certification, load profiling, power quality and reliability, and issues regarding contracts for transmission and distribution of electric power in an open electricity market received much attention. Concerns about the exercise of market power, and issues related to consumer choices and goals were also discussed. refs., tabs., figs

Plug Power

Energy Technology Data Exchange (ETDEWEB)

Marsh, A. [Plug Power Inc., New York, NY (United States)

2009-07-01

This presentation described Plug Power's GenDrive hydrogen fuel cell unit that supplies the power needs for folk lift trucks used in high-throughput distribution and high-volume manufacturing operations. The system offers an alternative to lead acid batteries, providing maximum performance at all times during use. The system is particularly useful in the material handling industry, where the revenue generated is based on operator uptime and lift truck productivity. The use of the system allows customers to reduce operational costs and expand valuable floor space by eliminating batteries and associated recharging infrastructure. Fuel cell units also reduce the wear on truck motors. Truck operators can easily and safely refuel at hydrogen fueling stations in 1-5 minutes. GenDrive works with all major OEM lift trucks, making the transition seamless. Commercial customers are investing in this solution to improve their current operations. In 2008, Plug Power sold to Wal-Mart, Bridgestone Firestone and Nestle. Most notably, Central Grocers purchased 220 fuel cell units for a new greenfield distribution center. Plug Power currently has more than 380 systems in operation.

Materials for advanced power engineering 2006. Proceedings of the 8th Liege conference. Pt. 1

Energy Technology Data Exchange (ETDEWEB)

Lecomte-Beckers, J; Carton, M; Schubert, F; Ennis, P J [eds.

2006-07-01

The European Co-operation in the field of Scientific and Technical Research (COST) is a well-established organisation for the co-ordination of national research and development programmes on the European level. The series of Liege conferences began in 1978 with the aim of disseminating the results of the COST Action 50 in which materials for gas turbines were investigated. Since then, a Liege Conference has been held every four years and the results of COST Actions 501 and 522, which were concerned with materials for power generation plant, reported. At this, the Eighth Liege Conference, the materials research and development work being carried out in the current COST Actions 536 'Alloy Development for Critical Components of Environmentally Friendly Steam Power Plant' with the acronym ACCEPT and 538 'High Temperature Plant Lifetime Extension' will be reported. Reliable energy supply at reasonable cost is one of the most important factors in the development and maintenance of the modern industrial society, but there are increasing concerns about the environmental impact of energy production as well as about the need to conserve valuable energy resources for future generations. New and emerging energy technologies are of great interest, but fossil fuels will continue to make a considerable contribution to energy requirements into the foreseeable future. The emphasis in this field is therefore on the most efficient use of fossil fuels, which can be achieved by increasing the thermal efficiency of the energy conversion process. For steam power plant and gas turbines, this means raising the temperature and pressure of the process. This in turn requires the application of improved materials that are able to withstand the increasingly arduous service conditions. In the COST Actions, the materials research and development activities that are necessary for the critical components of advanced, highly efficient power generation plant have been based on the principle of work

Materials for advanced power engineering 2006. Proceedings of the 8th Liege conference. Pt. 2

Energy Technology Data Exchange (ETDEWEB)

Lecomte-Beckers, J.; Carton, M.; Schubert, F.; Ennis, P.J. (eds.)

2006-07-01

The European Co-operation in the field of Scientific and Technical Research (COST) is a well-established organisation for the co-ordination of national research and development programmes on the European level. The series of Liege conferences began in 1978 with the aim of disseminating the results of the COST Action 50 in which materials for gas turbines were investigated. Since then, a Liege Conference has been held every four years and the results of COST Actions 501 and 522, which were concerned with materials for power generation plant, reported. At this, the Eighth Liege Conference, the materials research and development work being carried out in the current COST Actions 536 'Alloy Development for Critical Components of Environmentally Friendly Steam Power Plant' with the acronym ACCEPT and 538 'High Temperature Plant Lifetime Extension' will be reported. Reliable energy supply at reasonable cost is one of the most important factors in the development and maintenance of the modern industrial society, but there are increasing concerns about the environmental impact of energy production as well as about the need to conserve valuable energy resources for future generations. New and emerging energy technologies are of great interest, but fossil fuels will continue to make a considerable contribution to energy requirements into the foreseeable future. The emphasis in this field is therefore on the most efficient use of fossil fuels, which can be achieved by increasing the thermal efficiency of the energy conversion process. For steam power plant and gas turbines, this means raising the temperature and pressure of the process. This in turn requires the application of improved materials that are able to withstand the increasingly arduous service conditions. In the COST Actions, the materials research and development activities that are necessary for the critical components of advanced, highly efficient power generation plant have been based on the

Materials for advanced power engineering 2006. Proceedings of the 8th Liege conference. Pt. 1

International Nuclear Information System (INIS)

Lecomte-Beckers, J.; Carton, M.; Schubert, F.; Ennis, P.J.

2006-01-01

The European Co-operation in the field of Scientific and Technical Research (COST) is a well-established organisation for the co-ordination of national research and development programmes on the European level. The series of Liege conferences began in 1978 with the aim of disseminating the results of the COST Action 50 in which materials for gas turbines were investigated. Since then, a Liege Conference has been held every four years and the results of COST Actions 501 and 522, which were concerned with materials for power generation plant, reported. At this, the Eighth Liege Conference, the materials research and development work being carried out in the current COST Actions 536 'Alloy Development for Critical Components of Environmentally Friendly Steam Power Plant' with the acronym ACCEPT and 538 'High Temperature Plant Lifetime Extension' will be reported. Reliable energy supply at reasonable cost is one of the most important factors in the development and maintenance of the modern industrial society, but there are increasing concerns about the environmental impact of energy production as well as about the need to conserve valuable energy resources for future generations. New and emerging energy technologies are of great interest, but fossil fuels will continue to make a considerable contribution to energy requirements into the foreseeable future. The emphasis in this field is therefore on the most efficient use of fossil fuels, which can be achieved by increasing the thermal efficiency of the energy conversion process. For steam power plant and gas turbines, this means raising the temperature and pressure of the process. This in turn requires the application of improved materials that are able to withstand the increasingly arduous service conditions. In the COST Actions, the materials research and development activities that are necessary for the critical components of advanced, highly efficient power generation plant have been based on the principle of work

Materials for advanced power engineering 2006. Proceedings of the 8th Liege conference. Pt. 3

Energy Technology Data Exchange (ETDEWEB)

Lecomte-Beckers, J.; Carton, M.; Schubert, F.; Ennis, P.J. (eds.)

2006-07-01

The European Co-operation in the field of Scientific and Technical Research (COST) is a well-established organisation for the co-ordination of national research and development programmes on the European level. The series of Liege conferences began in 1978 with the aim of disseminating the results of the COST Action 50 in which materials for gas turbines were investigated. Since then, a Liege Conference has been held every four years and the results of COST Actions 501 and 522, which were concerned with materials for power generation plant, reported. At this, the Eighth Li ege Conference, the materials research and development work being carried out in the current COST Actions 536 'Alloy Development for Critical Components of Environmentally Friendly Steam Power Plant' with the acronym ACCEPT and 538 'High Temperature Plant Lifetime Extension' will be reported. Reliable energy supply at reasonable cost is one of the most important factors in the development and maintenance of the modern industrial society, but there are increasing concerns about the environmental impact of energy production as well as about the need to conserve valuable energy resources for future generations. New and emerging energy technologies are of great interest, but fossil fuels will continue to make a considerable contribution to energy requirements into the foreseeable future. The emphasis in this field is therefore on the most efficient use of fossil fuels, which can be achieved by increasing the thermal efficiency of the energy conversion process. For steam power plant and gas turbines, this means raising the temperature and pressure of the process. This in turn requires the application of improved materials that are able to withstand the increasingly arduous service conditions. In the COST Actions, the materials research and development activities that are necessary for the critical components of advanced, highly efficient power generation plant have been based on

Materials for advanced power engineering 2006. Proceedings of the 8th Liege conference. Pt. 3

Energy Technology Data Exchange (ETDEWEB)

Lecomte-Beckers, J; Carton, M; Schubert, F; Ennis, P J [eds.

2006-07-01

The European Co-operation in the field of Scientific and Technical Research (COST) is a well-established organisation for the co-ordination of national research and development programmes on the European level. The series of Liege conferences began in 1978 with the aim of disseminating the results of the COST Action 50 in which materials for gas turbines were investigated. Since then, a Liege Conference has been held every four years and the results of COST Actions 501 and 522, which were concerned with materials for power generation plant, reported. At this, the Eighth Li ege Conference, the materials research and development work being carried out in the current COST Actions 536 'Alloy Development for Critical Components of Environmentally Friendly Steam Power Plant' with the acronym ACCEPT and 538 'High Temperature Plant Lifetime Extension' will be reported. Reliable energy supply at reasonable cost is one of the most important factors in the development and maintenance of the modern industrial society, but there are increasing concerns about the environmental impact of energy production as well as about the need to conserve valuable energy resources for future generations. New and emerging energy technologies are of great interest, but fossil fuels will continue to make a considerable contribution to energy requirements into the foreseeable future. The emphasis in this field is therefore on the most efficient use of fossil fuels, which can be achieved by increasing the thermal efficiency of the energy conversion process. For steam power plant and gas turbines, this means raising the temperature and pressure of the process. This in turn requires the application of improved materials that are able to withstand the increasingly arduous service conditions. In the COST Actions, the materials research and development activities that are necessary for the critical components of advanced, highly efficient power generation plant have been based on the principle of work

Materials for advanced power engineering 2006. Proceedings of the 8th Liege conference. Pt. 1

Energy Technology Data Exchange (ETDEWEB)

Lecomte-Beckers, J.; Carton, M.; Schubert, F.; Ennis, P.J. (eds.)

2006-07-01

The European Co-operation in the field of Scientific and Technical Research (COST) is a well-established organisation for the co-ordination of national research and development programmes on the European level. The series of Liege conferences began in 1978 with the aim of disseminating the results of the COST Action 50 in which materials for gas turbines were investigated. Since then, a Liege Conference has been held every four years and the results of COST Actions 501 and 522, which were concerned with materials for power generation plant, reported. At this, the Eighth Liege Conference, the materials research and development work being carried out in the current COST Actions 536 'Alloy Development for Critical Components of Environmentally Friendly Steam Power Plant' with the acronym ACCEPT and 538 'High Temperature Plant Lifetime Extension' will be reported. Reliable energy supply at reasonable cost is one of the most important factors in the development and maintenance of the modern industrial society, but there are increasing concerns about the environmental impact of energy production as well as about the need to conserve valuable energy resources for future generations. New and emerging energy technologies are of great interest, but fossil fuels will continue to make a considerable contribution to energy requirements into the foreseeable future. The emphasis in this field is therefore on the most efficient use of fossil fuels, which can be achieved by increasing the thermal efficiency of the energy conversion process. For steam power plant and gas turbines, this means raising the temperature and pressure of the process. This in turn requires the application of improved materials that are able to withstand the increasingly arduous service conditions. In the COST Actions, the materials research and development activities that are necessary for the critical components of advanced, highly efficient power generation plant have been based on the

Summary of third international executive conference on photovoltaic power systems

Energy Technology Data Exchange (ETDEWEB)

Gillett, W.

2001-07-01

towards sustainable buildings fully into account. A further aim was to share the lessons learned from recent market experience on the full range of additional values that arise from the use of photovoltaic power systems and how those values impact on customer choice. Further, the promotion of international co-operation between the private and public sectors on policies for the removal of key constraints and for the promotion, financing and implementation of solar photovoltaic electricity projects was discussed. The conference was expected to achieve the following outcomes: Stronger relationships and networks between the participants and, through them, also between the sectors represented; A better definition of the added values of PV which influence customer choice; Recommendations which can be implemented by each of the business sectors represented at the conference for the orderly future development of the most important future PV markets; Recommendations to the IEA for ways in which it could enhance collaboration with both governments and industry, using its unique position to assist the future development of PV markets.

International Conference on Human Resource Development for Nuclear Power Programmes: Building and Sustaining Capacity. Presentations

International Nuclear Information System (INIS)

2014-01-01

The objectives of the conference are to: • Review developments in the global status of HRD since the 2010 international conference; • Emphasize the role of human resources and capacity building programmes at the national and organizational level for achieving safe, secure and sustainable nuclear power programmes; • Discuss the importance of building competence in nuclear safety and security; • Provide a forum for information exchange on national, as well as international, policies and practices; • Share key elements and best practices related to the experience of Member States that are introducing, operating or expanding nuclear power programmes; • Highlight the practices and issues regarding HRD at the organizational and national level; • Highlight education and training programmes and practices; • Emphasize the role of nuclear knowledge management for knowledge transfer and HRD; and • Elaborate on the role and scope of various knowledge networks

Optimization of lift gas allocation in a gas lifted oil field as non-linear optimization problem

Directory of Open Access Journals (Sweden)

Roshan Sharma

2012-01-01

Full Text Available Proper allocation and distribution of lift gas is necessary for maximizing total oil production from a field with gas lifted oil wells. When the supply of the lift gas is limited, the total available gas should be optimally distributed among the oil wells of the field such that the total production of oil from the field is maximized. This paper describes a non-linear optimization problem with constraints associated with the optimal distribution of the lift gas. A non-linear objective function is developed using a simple dynamic model of the oil field where the decision variables represent the lift gas flow rate set points of each oil well of the field. The lift gas optimization problem is solved using the emph'fmincon' solver found in MATLAB. As an alternative and for verification, hill climbing method is utilized for solving the optimization problem. Using both of these methods, it has been shown that after optimization, the total oil production is increased by about 4. For multiple oil wells sharing lift gas from a common source, a cascade control strategy along with a nonlinear steady state optimizer behaves as a self-optimizing control structure when the total supply of lift gas is assumed to be the only input disturbance present in the process. Simulation results show that repeated optimization performed after the first time optimization under the presence of the input disturbance has no effect in the total oil production.

Lift production through asymmetric flapping

Science.gov (United States)

Jalikop, Shreyas; Sreenivas, K. R.

2009-11-01

At present, there is a strong interest in developing Micro Air Vehicles (MAV) for applications like disaster management and aerial surveys. At these small length scales, the flight of insects and small birds suggests that unsteady aerodynamics of flapping wings can offer many advantages over fixed wing flight, such as hovering-flight, high maneuverability and high lift at large angles of attack. Various lift generating mechanims such as delayed stall, wake capture and wing rotation contribute towards our understanding of insect flight. We address the effect of asymmetric flapping of wings on lift production. By visualising the flow around a pair of rectangular wings flapping in a water tank and numerically computing the flow using a discrete vortex method, we demonstrate that net lift can be produced by introducing an asymmetry in the upstroke-to-downstroke velocity profile of the flapping wings. The competition between generation of upstroke and downstroke tip vortices appears to hold the key to understanding this lift generation mechanism.

From the ecological niche to the mass market with 'Green Power Marketing' - 1st European Conference on Green Power Marketing 2001

International Nuclear Information System (INIS)

2001-01-01

This report summarises the information presented at the European Conference on Green Power Marketing held in 2001 in St. Moritz, Switzerland. It takes a look at the market chances of ecologically produced electricity for use in Switzerland and for export. The opinions of experts from the areas of research, business, politics, marketing and non-governmental organisations that were presented at the meeting are summarised. European perspectives and trends in the USA are discussed and examples of green power marketing in the USA and Holland are given. Marketing issues and price policies are discussed, as are labelling strategies and customer perception of 'Green Power' issues. Also, sales issues including e-marketing, power-market rules and certificate trading are dealt with

Direct lifts of coupled cell networks

Science.gov (United States)

Dias, A. P. S.; Moreira, C. S.

2018-04-01

In networks of dynamical systems, there are spaces defined in terms of equalities of cell coordinates which are flow-invariant under any dynamical system that has a form consistent with the given underlying network structure—the network synchrony subspaces. Given a network and one of its synchrony subspaces, any system with a form consistent with the network, restricted to the synchrony subspace, defines a new system which is consistent with a smaller network, called the quotient network of the original network by the synchrony subspace. Moreover, any system associated with the quotient can be interpreted as the restriction to the synchrony subspace of a system associated with the original network. We call the larger network a lift of the smaller network, and a lift can be interpreted as a result of the cellular splitting of the smaller network. In this paper, we address the question of the uniqueness in this lifting process in terms of the networks’ topologies. A lift G of a given network Q is said to be direct when there are no intermediate lifts of Q between them. We provide necessary and sufficient conditions for a lift of a general network to be direct. Our results characterize direct lifts using the subnetworks of all splitting cells of Q and of all split cells of G. We show that G is a direct lift of Q if and only if either the split subnetwork is a direct lift or consists of two copies of the splitting subnetwork. These results are then applied to the class of regular uniform networks and to the special classes of ring networks and acyclic networks. We also illustrate that one of the applications of our results is to the lifting bifurcation problem.

Atoms for Power, Health and the Environment. 31st annual conference of the Canadian Nuclear Society and 34th annual conference of the Canadian Nuclear Society and Canadian Nuclear Association

International Nuclear Information System (INIS)

2010-01-01

The 31st Annual Conference of the CNS and 34th Annual Student Conference of the CNS and CNA was held in Montreal, Quebec, Canada on May 24-27, 2010. The theme of the conference, 'Atoms for Power, Health, and the Environment', brought together scientists, engineers, technologists and students interested in all aspects and applications of energy from the atom. The central objective of this conference was to provide a forum for exchange of views on how this technical enterprise can best serve the needs of humanity, now and in the future. There were over 400 attendees and more than 100 technical papers, as well as plenary sessions that addressed broad industrial and commercial developments in the field.

Vertical vector face lift.

Science.gov (United States)

Somoano, Brian; Chan, Joanna; Morganroth, Greg

2011-01-01

Facial rejuvenation using local anesthesia has evolved in the past decade as a safer option for patients seeking fewer complications and minimal downtime. Mini- and short-scar face lifts using more conservative incision lengths and extent of undermining can be effective in the younger patient with lower face laxity and minimal loose, elastotic neck skin. By incorporating both an anterior and posterior approach and using an incision length between the mini and more traditional face lift, the Vertical Vector Face Lift can achieve longer-lasting and natural results with lesser cost and risk. Submentoplasty and liposuction of the neck and jawline, fundamental components of the vertical vector face lift, act synergistically with superficial musculoaponeurotic system plication to reestablish a more youthful, sculpted cervicomental angle, even in patients with prominent jowls. Dramatic results can be achieved in the right patient by combining with other procedures such as injectable fillers, chin implants, laser resurfacing, or upper and lower blepharoplasties. © 2011 Wiley Periodicals, Inc.

JWST Lifting System

Science.gov (United States)

Tolleson, William

2012-01-01

A document describes designing, building, testing, and certifying a customized crane (Lifting Device LD) with a strong back (cradle) to facilitate the installation of long wall panels and short door panels for the GHe phase of the James Webb Space Telescope (JWST). The LD controls are variable-frequency drive controls designed to be adjustable for very slow and very-short-distance movements throughout the installation. The LD has a lift beam with an electric actuator attached at the end. The actuator attaches to a rectangular strong back (cradle) for lifting the long wall panels and short door panels from a lower angle into the vertical position inside the chamber, and then rotating around the chamber for installation onto the existing ceiling and floor. The LD rotates 360 (in very small increments) in both clockwise and counterclockwise directions. Eight lifting pads are on the top ring with 2-in. (.5-cm) eye holes spaced evenly around the ring to allow for the device to be suspended by three crane hoists from the top of the chamber. The LD is operated by remote controls that allow for a single, slow mode for booming the load in and out, with slow and very slow modes for rotating the load.

Motor-pump unit provided with a lifting appliance of the motor

International Nuclear Information System (INIS)

Veronesi, Luciano; Francis, W.R.

1978-01-01

This invention relates to lifting appliances and particularly concerns a 'pump and motor set' or motor-pump unit fitted with a lifting appliance enabling the motor to be separated from the pump. In nuclear power stations the reactor discharges heat that is carried by the coolant to a distant point away from the reactor to generate steam and electricity conventionally. In order to cause the reactor coolant to flow through the system, coolant motor-pump units are provided in the cooling system. These units are generally of the vertical type with an electric motor fitted vertically on the pump by means of a cylindrical or conical structure called motor support [fr

Papers of the 3. annual Canadian Institute conference on interjurisdictional power transactions

International Nuclear Information System (INIS)

2003-01-01

Leaders from the electric power industry in both Canada and the United States presented their views on a wide range of topics dealing with interjurisdictional power transactions. Participants presented ideas on how to prepare for the Federal Energy Regulatory Commission's (FERC) proposed new Standard Market Design. They also addressed the issue of how to overcome congestion for seamless power transactions between Canada and the Northeast. The way in which some companies and regions are preparing themselves for locational marginal pricing were also presented. Other topics included the state of the market power mitigation in Ontario, and increased trade potential within Ontario, Quebec and Atlantic Canada. Updates on the Lake Erie Link project were included along with a discussion on the expected impact it may have on trade capacity between Canada and the United States. The conference featured 18 presentations, of which 7 have been indexed separately for inclusion in this database. refs., tabs., figs

Water Chemistry and Chemistry Monitoring at Thermal and Nuclear Power Plants: Problems and Tasks (Based on Proceedings of Conferences)

Science.gov (United States)

Larin, B. M.

2018-02-01

In late May-early June 2017, two international science and technology conferences on problems of water chemistry and chemistry monitoring at thermal and nuclear power plants were held. The participants of both the first conference held at OAO VTI and the second conference that took place at NITI formulated the problems of the development of the regulatory base and implementation of promising water treatment technologies and outlined the ways of improving the water chemistry and chemistry monitoring at TPPs and NPPs for the near future. It was pointed out that the new amine-containing VTIAMIN agent developed by OAO VTI had been successfully tested on the power-generating units equipped with steam-gas plants to establish the minimum excess of the film-forming amine in the power-generating unit circuit that ensures the protection of the metal as 5-10 μg/dm3. A flow-injection technique for the analysis of trace concentrations of chlorides was proposed; the technique applied to the condensate of the 1000-MW steam turbine of the NPP power-generating unit yields the results comparable with the results obtained by the ion chromatography and the potentiometric method using the solver electrode. The participants of the conferences were demonstrated new Russian instruments to analyze the water media at the TPPs and NPPs, including the total organic carbon analyzer and the analyzer of mineral impurities in the condensate and feed water, that won a gold medal at the 45th International Exhibition of Inventions held in Geneva this April.

5. annual clean coal technology conference: powering the next millennium. Vol.1

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-07-01

The Fifth Annual Clean Coal Technology Conference focuses on presenting strategies and approaches that will enable clean coal technologies to resolve the competing, interrelated demands for power, economic viability, and environmental constraints associated with the use of coal in the post-2000 era. The program addresses the dynamic changes that will result from utility competition and industry restructuring, and to the evolution of markets abroad. Current projections for electricity highlight the preferential role that electric power will have in accomplishing the long-range goals of most nations. Increased demands can be met by utilizing coal in technologies that achieve environmental goals while keeping the cost- per-unit of energy competitive. Results from projects in the DOE Clean Coal technology Demonstration Program confirm that technology is the pathway to achieving these goals. The industry/government partnership, cemented over the past 10 years, is focused on moving the clean coal technologies into the domestic and international marketplaces. The Fifth Annual Clean Coal Technology Conference provides a forum to discuss these benchmark issues and the essential role and need for these technologies in the post-2000 era. This volume contains papers presented at the plenary session and panel sessions on; international markets for clean coal technologies (CCTs); role of CCTs in the evolving domestic electricity market; environmental issues affecting CCT deployment; and CCT deployment from today into the next millennium. In addition papers presented at the closing plenary session on powering the next millennium--CCT answers the challenge are included. Selected papers have been processed for inclusion in the Energy Science and Technology database.

Statement to international conference on human resource development for introducing and expanding nuclear power programs

International Nuclear Information System (INIS)

Amano, Y.

2010-03-01

Full text: Mr. President, Excellencies, Ladies and Gentlemen, It is a pleasure for me to open this IAEA conference on Human Resource Development for Introducing and Expanding Nuclear Power Programmes. I am very grateful to the Government of the United Arab Emirates for hosting this important event. As you know, the world is witnessing a resurgence of interest in nuclear power. The IAEA has projects on introducing nuclear power with no fewer than fifty-eight of our Member States. We expect between 10 and 25 new countries to bring their first nuclear power plants on-line by 2030. These are momentous changes. However, some countries are concerned about a possible shortage of skilled professionals in the nuclear field in the coming decades. The generation of professionals who built and led the nuclear power industry for much of the past 50 years is approaching retirement and in some countries there are not enough students coming up through the educational system to take their place. Naturally, we at the IAEA want to do all we can to help Member States address this issue. That is why we have organized this conference. The situation is different in different countries. For countries with expanding nuclear power programmes, the challenge is to scale up their existing education and training in order to have the required qualified workforce on time. Countries planning to supply nuclear technology to others not only have to meet their national human resource needs, but must also be able to transfer education and training capacity together with the technology they provide. Finally, countries embarking on nuclear power cannot become too dependent on their technology supplier and need to develop their own home-grown expertise and skills base. The Agency would be happy to help interested States to formulate country-specific policies on human resource development, education, training and knowledge management in support of nuclear power programmes. We could also help countries

Statement to International Conference on Human Resource Development for Introducing and Expanding Nuclear Power Programs

International Nuclear Information System (INIS)

Amano, Y.

2012-01-01

Mr. President, Excellencies, Ladies and Gentlemen, It is a pleasure for me to open this IAEA conference on Human Resource Development for Introducing and Expanding Nuclear Power Programmes. I am very grateful to the Government of the United Arab Emirates for hosting this important event. As you know, the world is witnessing a resurgence of interest in nuclear power. The IAEA has projects on introducing nuclear power with no fewer than fifty-eight of our Member States. We expect between 10 and 25 new countries to bring their first nuclear power plants on-line by 2030. These are momentous changes. However, some countries are concerned about a possible shortage of skilled professionals in the nuclear field in the coming decades. The generation of professionals who built and led the nuclear power industry for much of the past 50 years is approaching retirement and in some countries there are not enough students coming up through the educational system to take their place. Naturally, we at the IAEA want to do all we can to help Member States address this issue. That is why we have organized this conference. The situation is different in different countries. For countries with expanding nuclear power programmes, the challenge is to scale up their existing education and training in order to have the required qualified workforce on time. Countries planning to supply nuclear technology to others not only have to meet their national human resource needs, but must also be able to transfer education and training capacity together with the technology they provide. Finally, countries embarking on nuclear power cannot become too dependent on their technology supplier and need to develop their own home-grown expertise and skills base. The Agency would be happy to help interested States to formulate country-specific policies on human resource development, education, training and knowledge management in support of nuclear power programmes. We could also help countries make better

Business Profile of Boat Lift Net and Stationary Lift Net Fishing Gear in Morodemak Waters Central Java

Science.gov (United States)

Hapsari, Trisnani D.; Jayanto, Bogi B.; Fitri, Aristi D. P.; Triarso, I.

2018-02-01

Lift net is one of the fishing gears that is used widely in the Morodemak coastal fishing port (PPP) for catching pelagic fish. The yield of fish captured by these fishing gear has high economic value, such as fish belt (Trichiurus sp), squids (Loligo sp) and anchovies (Stelophorus sp). The aims of this research were to determine the technical aspects of boat lift net and stationary lift net fishing gear in Morodemak Waters Demak Regency; to find out the financial aspect of those fishing gears and to analyze the financial feasibility by counting PP, NPV, IRR, and B/C ratio criteria. This research used case study method with descriptive analysis. The sampling method was purposive sampling with 22 fishermen as respondents. The result of the research showed that the average of boat lift net acceptance was Rp 388,580,000. The financial analysis of fisheries boat lift net with the result of NPV Rp 836,149,272, PP 2.44 years, IRR value 54%, and B/C ratio 1.73. The average of stationary lift net acceptance was Rp 27,750,000. The financial analysis lift net with the result of NPV Rp 37,937,601; PP 1.96 years, IRR value 86%, and B/C ratio 1.32. This research had a positive NPV value, B/C ratio >1, and IRR > discount rate (12 %). This study concluded that the fishery business of boat lift net and stationary lift net in Morodemak coastal fishing port (PPP) was worth running.

A comparative analysis of lumbar spine mechanics during barbell- and crate-lifting: implications for occupational lifting task assessments.

Science.gov (United States)

Zehr, Jackie D; Carnegie, Danielle R; Welsh, Timothy N; Beach, Tyson A C

2018-03-19

To compare the effects of object handled and handgrip used on lumbar spine motion and loading during occupational lifting task simulations. Eight male and eight female volunteers performed barbell and crate lifts with a pronated (barbell) and a neutral (crate) handgrip. The mass of barbells/crates lifted was identical across the objects and fixed at 11.6 and 9.3 kg for men and women, respectively. The initial heights of barbells/crates were individualized to mid-shank level. Body segment kinematics and foot-ground reaction kinetics were collected, and then input into an electromyography-assisted dynamic biomechanical model to quantify lumbar spine motion and loading. Lumbar compression and net lumbosacral moment magnitudes were 416 N and 17 Nm lower when lifting a barbell than when lifting a crate (p  0.392) or flexion/extension velocities (p > 0.085). Crate- and barbell-lifting tasks can be used interchangeably if assessing lifting mechanics based on peak spine motion variables. If assessments are based on the spine loading responses to task demands, however, then crate- and barbell-lifting tasks cannot be used interchangeably.

Occupational lifting of heavy loads and preterm birth:

DEFF Research Database (Denmark)

Runge, Stine Bjerrum; Pedersen, Jacob Krabbe; Svendsen, Susanne Wulff

2013-01-01

To examine the association between occupational lifting during pregnancy and preterm birth. The risk of preterm birth was estimated for total burden lifted per day and number of medium and heavy loads lifted per day.......To examine the association between occupational lifting during pregnancy and preterm birth. The risk of preterm birth was estimated for total burden lifted per day and number of medium and heavy loads lifted per day....

Application of lift and squeeze technique in phacoemulsification of hypermature cataract

Directory of Open Access Journals (Sweden)

Geng-Ying Li

2014-07-01

Full Text Available AIM: To evaluate the effectiveness and security of lift and squeeze technique in phacoemulsification of hypermature cataract.METHODS: From June 2010 to June 2013, totally 156 eyes with hypermature cataract, which received phacoemulsification in our hospital, were enrolled. Lift and squeeze technique was used to chop the nucleus, and 1g/L Trypan blue was used for capsulorhexis. Average time of phaco complication, corneal edema and visual outcome were recorded.RESULTS: The best-corrected visual acuity(BCVA was 0.1-0.4 in 15 eyes(9.6%, 0.5-0.7 in 82(52.6%eyes, and 0.8-1.0 in 59(37.8%eyes at 3mo after surgery. The phaco time was 25-56s(average 42±10s, the maximum phaco power was 30%. Posterior capsular rupture and vitreous loss happened in 2 eyes(1.3%, and the IOLs were implanted in the sulcus. Corneal edema classified at grade Ⅰ were seen in 12 eyes(7.7%, and 5 eyes(3.2%at gradeⅡ, no eye at grade Ⅲ and grade Ⅳ. The mean endothelial cell loss was 8.7% at 3mo.CONCLUSION: Crystalline lens capsule staining with Trypan blue increase the success rate of intact continuous curvilinear capsulorhexis(CCC. The lift and squeeze technique reduces the stress on the zonules and capsule, and decreases the phaco time and phaco power.

Fish's Muscles Distortion and Pectoral Fins Propulsion of Lift-Based Mode

Science.gov (United States)

Yang, S. B.; Han, X. Y.; Qiu, J.

As a sort of MPF(median and/or paired fin propulsion), pectoral fins propulsion makes fish easier to maneuver than other propulsion, according to the well-established classification scheme proposed by Webb in 1984. Pectoral fins propulsion is classified into oscillatory propulsion, undulatory propulsion and compound propulsion. Pectoral fins oscillatory propulsion, is further ascribable to two modes: drag-based mode and lift-based mode. And fish exhibits strong cruise ability by using lift-based mode. Therefore to robot fish design using pectoral fins lift-based mode will bring a new revolution to resources exploration in blue sea. On the basis of the wave plate theory, a kinematic model of fish’s pectoral fins lift-based mode is established associated with the behaviors of cownose ray (Rhinoptera bonasus) in the present work. In view of the power of fish’s locomotion from muscle distortion, it would be helpful benefit to reveal the mechanism of fish’s locomotion variation dependent on muscles distortion. So this study puts forward the pattern of muscles distortion of pectoral fins according to the character of skeletons and muscles of cownose ray in morphology and simulates the kinematics of lift-based mode using nonlinear analysis software. In the symmetrical fluid field, the model is simulated left-right symmetrically or asymmetrically. The results qualitatively show how muscles distortion determines the performance of fish locomotion. Finally the efficient muscles distortion associated with the preliminary dynamics is induced.

75 FR 52528 - Mandatory Reliability Standards for the Bulk-Power System; Notice of Technical Conference

Science.gov (United States)

2010-08-26

...] Mandatory Reliability Standards for the Bulk-Power System; Notice of Technical Conference August 19, 2010... Order No. 693 the Commission approved Reliability Standard BAL-003-0 as mandatory and enforceable and directed the ERO to develop a modification to BAL-003-0 through the Reliability Standards development...

Thread-Lift Sutures : Still in the Lift? A Systematic Review of the Literature

NARCIS (Netherlands)

Gulbitti, Haydar Aslan; Colebunders, Britt; Pirayesh, Ali; Bertossi, Dario; van der Lei, Berend

Background: In 2006, Villa et al. published a review article concerning the use of thread-lift sutures and concluded that the technique was still in its infancy but had great potential to become a useful and effective procedure for nonsurgical lifting of sagged facial tissues. As 11 years have

Thread-Lift Sutures : Still in the Lift? A Systematic Review of the Literature

NARCIS (Netherlands)

Gülbitti, Haydar Aslan; Colebunders, Britt; Pirayesh, Ali; Bertossi, Dario; van der Lei, Berend

2018-01-01

BACKGROUND: In 2006, Villa et al. published a review article concerning the use of thread-lift sutures and concluded that the technique was still in its infancy but had great potential to become a useful and effective procedure for nonsurgical lifting of sagged facial tissues. As 11 years have

Proceedings of the 7. world wind energy conference 2008 : community power : energy autonomy for local economies

International Nuclear Information System (INIS)

2008-01-01

This international conference profiled the topic of community power within the dynamic renewable energy sector. The objective was to promote international technology transfer and bring a new perspective to community development, economic growth and environmental awareness in the context of climate change. It was attended by academics and industry representatives from 20 countries who focused on leading edge research on the topic of innovative technology in the rapidly growing renewable power market. The topics of discussion addressed issues such as ownership of renewable energy projects by local communities, including farmers, landowners, cooperatives, Aboriginal groups, municipalities, utilities and educational institutions. Presentations focused on policy development, financial mechanisms, ownership models, technology advancements, grid interconnection issues, governance and capacity building. The conference featured more than 100 presentations, of which 65 have been catalogued separately for inclusion in this database. refs., tabs., figs

Proceedings of the 9th NUSIM 2000 Conference. Joint Slovak, Czech and German Seminar on Nuclear Power

International Nuclear Information System (INIS)

2000-01-01

Scientific conference deals with problems of reactor safety upgrading, mainly of two blocks of the NPP V-1 Bohunice as well as decomissioning of the NPP A-1 Bohunice. Other problems of the nuclear engineering were discussed. Totally, 201 participants from the Slovak Republic, Czech Republic and Germany and from other countries took part in the conference. The Conference included the following sessions: (i): Survey on the situation of nuclear power in the partner countries; (ii) Mochovce design safety enhacement and operational experience; (iii) Bohunice V-1 safety upgrading and operational experience; (iv) Decomissioning, spent fuel and radwaste management; (v) Young Generation Presentation. Proceedings contains thirty one papers dealing with the scope of INIS

Evaluation of structure integrity of the lifting handle of CRB

Energy Technology Data Exchange (ETDEWEB)

Wu, S.-Y. [Radiation Protection Association, Taiwan (China); Lin, S.-R. [Radiation Protection Association, Taiwan (China)], E-mail: srlin@iner.gov.tw; Kang, L.-C. [Institute of Nuclear Energy Research, Taiwan (China); Chang, Han-Jou [Department of Nuclear Safety, TPC, Taiwan (China)

2008-09-15

Since visual inspection was applied to inspect the control rod blades (CRBs) of nuclear power plants in Taiwan, indications have been found in areas such as roller-pin hole, sheath and tie-rod of CRB. Many preliminary safety analyses with conservative assumptions have been conducted to endorse the continuing operation of the units. The objective of this study is to evaluate the structural integrity of those CRBs during lifting operation. Detailed finite element models of the lifting handle of the CRB are built with emphasis on the postulated crack near the roller-pin hole. Both the D-215 type CRB and the Marathon type CRB are evaluated. It is concluded that the structural integrity is guaranteed even under the worst postulated situation.

Optimization of reproductive management programs using lift chart analysis and cost-sensitive evaluation of classification errors.

Science.gov (United States)

Shahinfar, Saleh; Guenther, Jerry N; Page, C David; Kalantari, Afshin S; Cabrera, Victor E; Fricke, Paul M; Weigel, Kent A

2015-06-01

yield relative to contemporaries. In the second data set, the strategy of inseminating only a subset consisting of 59% of the most fertile cows conferred a gain in profit of $5.21 per eligible cow in a monthly breeding period. These results suggest that, when used with a powerful classification algorithm, lift chart analysis and cost-sensitive evaluation of correctly classified and misclassified insemination events can enhance the performance and profitability of reproductive management programs on commercial dairy farms. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

International conference on management of radioactive waste from non-power applications - Sharing the experience. Book of extended synopses

International Nuclear Information System (INIS)

2001-01-01

The primary objective of the conference is to provide an opportunity for experts in this field to meet and exchange information, and to discuss experience, specific practices and technical solutions used in the management of radioactive waste derived from different non-power applications. This includes waste from the operation of research reactors, and from the production and application of radioisotopes, labelled compounds and sealed radioactive sources in industry, medicine, agriculture, research and education. The discussion may also include management of specific waste types, such as waste from radiological accidents, waste from remediation activities connected with old, inadequate waste management facilities, etc. The conference may also address the issues of management of very low level radioactive waste (VLLRW) and of technologically enhanced naturally occurring radioactive materials (TENORMs) to identify the existing scale of the problems and to analyse current approaches of Member States to their solution. The conference is also intended to identify the most important and problematic components of the subject and to facilitate the sharing of experience in improving efficiency, safety and economy in the management of radioactive waste from non-power nuclear applications. This publication contains 89 extended synopses of the oral and poster presentations delivered at the conference. Each of them was indexed separately

Measurement of circulation around wing-tip vortices and estimation of lift forces using stereo PIV

Science.gov (United States)

Asano, Shinichiro; Sato, Haru; Sakakibara, Jun

2017-11-01

Applying the flapping flight to the development of an aircraft as Mars space probe and a small aircraft called MAV (Micro Air Vehicle) is considered. This is because Reynolds number assumed as the condition of these aircrafts is low and similar to of insects and small birds flapping on the earth. However, it is difficult to measure the flow around the airfoil in flapping flight directly because of its three-dimensional and unsteady characteristics. Hence, there is an attempt to estimate the flow field and aerodynamics by measuring the wake of the airfoil using PIV, for example the lift estimation method based on a wing-tip vortex. In this study, at the angle of attack including the angle after stall, we measured the wing-tip vortex of a NACA 0015 cross-sectional and rectangular planform airfoil using stereo PIV. The circulation of the wing-tip vortex was calculated from the obtained velocity field, and the lift force was estimated based on Kutta-Joukowski theorem. Then, the validity of this estimation method was examined by comparing the estimated lift force and the force balance data at various angles of attack. The experiment results are going to be presented in the conference.

3. International Conference on Nuclear Power Plant Life Management (PLiM) for Long Term Operations (LTO). Keynotes, papers, presentations, posters

International Nuclear Information System (INIS)

2012-01-01

The world's fleet of nuclear power plants is, on average, more than 20 years old. Even though the design life of a nuclear power plant is typically 30-40 years, many plants will operate in excess of their design lives, provided that nuclear power plant engineers demonstrate by analysis, equipment and system upgrades, increased vigilance, testing and ageing management that the plant will operate safely. In the operation of nuclear power plants, safety should always be the prime consideration. Plant operators and regulators must always ensure that plant safety is maintained and, where possible, enhanced during its operating lifetime. Nuclear power plant life management (PLiM) has gained increased attention over the past decade, and effective ageing management of systems, structures and components (SSCs) is a key element in PLiM for the safe and reliable long term operation of nuclear power plants. A PLiM programme is an effective tool that allows an operator to safely and cost effectively manage ageing effects in SSCs for long term operation (LTO). A PLiM programme helps facilitate decisions concerning when and how to repair, replace or modify SSCs in an economically optimized way, while assuring that a high level of safety is maintained. The option for extended nuclear power plant operation has been recognized by operators and regulators alike, as evidenced in the number of licence renewal programmes that are being developed by Member States. After the severe accident at the Fukushima Daiichi nuclear power plant, the safe operation of nuclear power plants has become even more important; not only in terms of technical or ageing issues, but also in terms of management system and qualified workforce related issues. Application of an integrated management system and structured workforce planning are needed throughout the plant life in order to ensure effective plant organization and management. The IAEA organized the first and second International Conference on Nuclear

Wingless Flight: The Lifting Body Story

Science.gov (United States)

Reed, R. Dale; Lister, Darlene (Editor); Huntley, J. D. (Editor)

1997-01-01

Wingless Flight tells the story of the most unusual flying machines ever flown, the lifting bodies. It is my story about my friends and colleagues who committed a significant part of their lives in the 1960s and 1970s to prove that the concept was a viable one for use in spacecraft of the future. This story, filled with drama and adventure, is about the twelve-year period from 1963 to 1975 in which eight different lifting-body configurations flew. It is appropriate for me to write the story, since I was the engineer who first presented the idea of flight-testing the concept to others at the NASA Flight Research Center. Over those twelve years, I experienced the story as it unfolded day by day at that remote NASA facility northeast of los Angeles in the bleak Mojave Desert. Benefits from this effort immediately influenced the design and operational concepts of the winged NASA Shuttle Orbiter. However, the full benefits would not be realized until the 1990s when new spacecraft such as the X-33 and X-38 would fully employ the lifting-body concept. A lifting body is basically a wingless vehicle that flies due to the lift generated by the shape of its fuselage. Although both a lifting reentry vehicle and a ballistic capsule had been considered as options during the early stages of NASA's space program, NASA initially opted to go with the capsule. A number of individuals were not content to close the book on the lifting-body concept. Researchers including Alfred Eggers at the NASA Ames Research Center conducted early wind-tunnel experiments, finding that half of a rounded nose-cone shape that was flat on top and rounded on the bottom could generate a lift-to-drag ratio of about 1.5 to 1. Eggers' preliminary design sketch later resembled the basic M2 lifting-body design. At the NASA Langley Research Center, other researchers toyed with their own lifting-body shapes. Meanwhile, some of us aircraft-oriented researchers at the, NASA Flight Research Center at Edwards Air

Proceedings of the 7. Independent Power Producers' Society of Alberta annual conference

International Nuclear Information System (INIS)

2001-01-01

This conference provided to the delegates from across North America a forum where a wide array of perspectives with regard to the new electric market place of Alberta could be discussed. Speakers covered a lot of ground in their examination of the deregulation of the electricity market in Alberta and the impacts felt by consumers and producers alike. The recent events that led to the deregulation were reviewed and an emphasis was also placed on the successful development of power generation projects, wholesale pricing options and independent retail strategies. Open energy markets were discussed in a series of speaker panels where representatives from private organizations added their views on the topic. The conference was divided into seven sessions entitled: (1) the operation of Alberta's market, (2) panel discussion: defending the market, (3) competitive hurdles to successful development, (4) alternative energy solutions, (5) mechanics of retail choice, (6) wholesale pricing options, and (7) independent retailer strategies. refs., tabs., figs

Offshore Newfoundland: from a project to an industry. Conference '95 proceedings

International Nuclear Information System (INIS)

Keough, S.

1995-01-01

The Proceedings of the 11. International Offshore Petroleum Conference consists of 18 papers, organized into four sessions, dealing, respectively, with (1) Hibernia today, (2) downstream operations, (3) future developments, and (4) international marketing and competitiveness. The majority of the papers dealt with the Hibernia project off the coast of Newfoundland. An update of the project to date, planning for the start-up of production, lifting and transportation problems, plans for the Come By Chance refinery, future developments, marketing Newfoundland's offshore expertise internationally, and perspectives on the international oil and gas industry were the principal issues discussed. A list of conference participants was also included. Figs., tabs

Wavelets and the Lifting Scheme

DEFF Research Database (Denmark)

la Cour-Harbo, Anders; Jensen, Arne

The objective of this article is to give a concise introduction to the discrete wavelet transform (DWT) based on a technique called lifting. The lifting technique allows one to give an elementary, but rigorous, definition of the DWT, with modest requirements on the reader. A basic knowledge...... of linear algebra and signal processing will suffice. The lifting based definition is equivalent to the usual filer bank based definition of the DWT. The article does not discuss applications in any detail. The reader is referred to other articles in this collection....

Wavelets and the lifting scheme

DEFF Research Database (Denmark)

la Cour-Harbo, Anders; Jensen, Arne

2012-01-01

The objective of this article is to give a concise introduction to the discrete wavelet transform (DWT) based on a technique called lifting. The lifting technique allows one to give an elementary, but rigorous, definition of the DWT, with modest requirements on the reader. A basic knowledge...... of linear algebra and signal processing will suffice. The lifting based definition is equivalent to the usual filer bank based definition of the DWT. The article does not discuss applications in any detail. The reader is referred to other articles in this collection....

Wavelets and the lifting scheme

DEFF Research Database (Denmark)

la Cour-Harbo, Anders; Jensen, Arne

2009-01-01

The objective of this article is to give a concise introduction to the discrete wavelet transform (DWT) based on a technique called lifting. The lifting technique allows one to give an elementary, but rigorous, definition of the DWT, with modest requirements on the reader. A basic knowledge...... of linear algebra and signal processing will suffice. The lifting based definition is equivalent to the usual filer bank based definition of the DWT. The article does not discuss applications in any detail. The reader is referred to other articles in this collection....

Heterotic weight lifting

International Nuclear Information System (INIS)

Gato-Rivera, B.; Schellekens, A.N.

2010-01-01

We describe a method for constructing genuinely asymmetric (2,0) heterotic strings out of N=2 minimal models in the fermionic sector, whereas the bosonic sector is only partly build out of N=2 minimal models. This is achieved by replacing one minimal model plus the superfluous E 8 factor by a non-supersymmetric CFT with identical modular properties. This CFT generically lifts the weights in the bosonic sector, giving rise to a spectrum with fewer massless states. We identify more than 30 such lifts, and we expect many more to exist. This yields more than 450 different combinations. Remarkably, despite the lifting of all Ramond states, it is still possible to get chiral spectra. Even more surprisingly, these chiral spectra include examples with a certain number of chiral families of SO(10), SU(5) or other subgroups, including just SU(3)xSU(2)xU(1). The number of families and mirror families is typically smaller than in standard Gepner models. Furthermore, in a large number of different cases, spectra with three chiral families can be obtained. Based on a first scan of about 10% of the lifted Gepner models we can construct, we have collected more than 10,000 distinct spectra with three families, including examples without mirror fermions. We present an example where the GUT group is completely broken to the standard model, but the resulting and inevitable fractionally charged particles are confined by an additional gauge group factor.

Heterotic weight lifting

Energy Technology Data Exchange (ETDEWEB)

Gato-Rivera, B. [NIKHEF Theory Group, Kruislaan 409, 1098 SJ Amsterdam (Netherlands); Instituto de Fisica Fundamental, CSIC, Serrano 123, Madrid 28006 (Spain); Schellekens, A.N., E-mail: t58@nikhef.n [NIKHEF Theory Group, Kruislaan 409, 1098 SJ Amsterdam (Netherlands); Instituto de Fisica Fundamental, CSIC, Serrano 123, Madrid 28006 (Spain); IMAPP, Radboud Universiteit, Nijmegen (Netherlands)

2010-03-21

We describe a method for constructing genuinely asymmetric (2,0) heterotic strings out of N=2 minimal models in the fermionic sector, whereas the bosonic sector is only partly build out of N=2 minimal models. This is achieved by replacing one minimal model plus the superfluous E{sub 8} factor by a non-supersymmetric CFT with identical modular properties. This CFT generically lifts the weights in the bosonic sector, giving rise to a spectrum with fewer massless states. We identify more than 30 such lifts, and we expect many more to exist. This yields more than 450 different combinations. Remarkably, despite the lifting of all Ramond states, it is still possible to get chiral spectra. Even more surprisingly, these chiral spectra include examples with a certain number of chiral families of SO(10), SU(5) or other subgroups, including just SU(3)xSU(2)xU(1). The number of families and mirror families is typically smaller than in standard Gepner models. Furthermore, in a large number of different cases, spectra with three chiral families can be obtained. Based on a first scan of about 10% of the lifted Gepner models we can construct, we have collected more than 10,000 distinct spectra with three families, including examples without mirror fermions. We present an example where the GUT group is completely broken to the standard model, but the resulting and inevitable fractionally charged particles are confined by an additional gauge group factor.

Development of a Publications and Conferences Data Base in the Mexican Electric Power Research Institute.

Science.gov (United States)

Ripoll, C. Lopez Cerdan; And Others

This paper describes the development by the Mexican Electric Power Research Institute (Instituto de Investigaciones Electricas or IIE) over a 10-year period of a publications and conferences database (PCDB) of research and development output of the institute. The paper begins by listing the objectives of the database and describing data coverage…

Lambda-lifting in Quadratic Time

DEFF Research Database (Denmark)

Danvy, O.; Schultz, U.P.

2004-01-01

-lifting transforms a block-structured program into a set of recursive equations, one for each local function in the source program. Each equation carries extra parameters to account for the free variables of the corresponding local function and of all its callees. It is the search for these extra parameters......Lambda-lifting is a program transformation that is used in compilers, partial evaluators, and program transformers. In this article, we show how to reduce its complexity from cubic time to quadratic time, and we present a flow-sensitive lambda-lifter that also works in quadratic time. Lambda...... that yields the cubic factor in the traditional formulation of lambda-lifting, which is due to Johnsson. This search is carried out by computing a transitive closure. To reduce the complexity of lambda-lifting, we partition the call graph of the source program into strongly connected components, based...

77 FR 11109 - Reactive Power Resources; Notice of Technical Conference

Science.gov (United States)

2012-02-24

... technical conference will be led by Commission staff. At the conference, discussion items will include: the... technical conference in this proceeding is also available. Anyone with Internet access interested in viewing...

International conference on innovative technologies for nuclear fuel cycles and nuclear power. Book of extended synopses

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-07-01

A wide range of issues relevant to the innovative technologies for nuclear power cycle and nuclear power were addressed. The 7 sessions of the conference were entitled: (1) no title; (2) needs, prospects and challenges for innovation; (3) evolution of technical, social, economic and political conditions; (4) panel on challenges for the deployment of innovative technologies; (5) international programmes on innovative nuclear systems; (6) innovative nuclear systems and related R and D programmes; (7) concluding panel.

Modeling lift operations with SASmacr Simulation Studio

Science.gov (United States)

Kar, Leow Soo

2016-10-01

Lifts or elevators are an essential part of multistorey buildings which provide vertical transportation for its occupants. In large and high-rise apartment buildings, its occupants are permanent, while in buildings, like hospitals or office blocks, the occupants are temporary or users of the buildings. They come in to work or to visit, and thus, the population of such buildings are much higher than those in residential apartments. It is common these days that large office blocks or hospitals have at least 8 to 10 lifts serving its population. In order to optimize the level of service performance, different transportation schemes are devised to control the lift operations. For example, one lift may be assigned to solely service the even floors and another solely for the odd floors, etc. In this paper, a basic lift system is modelled using SAS Simulation Studio to study the effect of factors such as the number of floors, capacity of the lift car, arrival rate and exit rate of passengers at each floor, peak and off peak periods on the system performance. The simulation is applied to a real lift operation in Sunway College's North Building to validate the model.

Apparent Power, Expanded Definitions, Transient Operating Conditions, Network Reactions, Compensation, Papers Presented at ETG Conference (Energy Technology Society), 1979

Energy Technology Data Exchange (ETDEWEB)

1980-01-01

The Proceedings of the Conference comprises 12 papers dealing with the following themes: the history of apparent power; active and apparent power of periodical currents in single-phase and multiphase systems with periodical voltages of any shape of curve; power values in unsteady state processes; power and harmonic relations in mains-controlled direct frequency converters; power electronic devices for apparent power compensation; electric arc effects on power system: characteristics, measurement methods, compensation; harmonic compensation by means of impedance wave trap filters in rectifiers; compensation of apparent power by filter circuits; apparent power effects on ac railroad power systems; effects of apparent power in low-voltage networks of public power supply.

Masculinity and Lifting Accidents among Danish Ambulance Personnel

DEFF Research Database (Denmark)

Hansen, Claus D.; Nielsen, Kent J

Background Work injuries related to lifting are the most prevalent among ambulance personnel (AP) despite the introduction of ‘assistive technologies’ (AT) that help reduce situations of manual lifting. One third of the AP report using AT only ‘sometimes’ and 10% report having lifted a patient...... alone. Aim This presentation investigates whether failure to use AT is linked to male ambulance workers’ gender identity? Is lifting patients alone a way of performing masculinity for AP’s? Method Data is taken from MARS, a panel study of AP workers in Denmark (n = 1606). Information from questionnaires...... measuring traditional male role norms (MRNI), safety attitudes and safety behavior will be linked to company register information on work injuries categorized as lifting accidents. Logistic regression is used to analyse associations between masculinity, lifting behavior, and lifting accidents. Results...

AFC-Enabled Simplified High-Lift System Integration Study

Science.gov (United States)

Hartwich, Peter M.; Dickey, Eric D.; Sclafani, Anthony J.; Camacho, Peter; Gonzales, Antonio B.; Lawson, Edward L.; Mairs, Ron Y.; Shmilovich, Arvin

2014-01-01

The primary objective of this trade study report is to explore the potential of using Active Flow Control (AFC) for achieving lighter and mechanically simpler high-lift systems for transonic commercial transport aircraft. This assessment was conducted in four steps. First, based on the Common Research Model (CRM) outer mold line (OML) definition, two high-lift concepts were developed. One concept, representative of current production-type commercial transonic transports, features leading edge slats and slotted trailing edge flaps with Fowler motion. The other CRM-based design relies on drooped leading edges and simply hinged trailing edge flaps for high-lift generation. The relative high-lift performance of these two high-lift CRM variants is established using Computational Fluid Dynamics (CFD) solutions to the Reynolds-Averaged Navier-Stokes (RANS) equations for steady flow. These CFD assessments identify the high-lift performance that needs to be recovered through AFC to have the CRM variant with the lighter and mechanically simpler high-lift system match the performance of the conventional high-lift system. Conceptual design integration studies for the AFC-enhanced high-lift systems were conducted with a NASA Environmentally Responsible Aircraft (ERA) reference configuration, the so-called ERA-0003 concept. These design trades identify AFC performance targets that need to be met to produce economically feasible ERA-0003-like concepts with lighter and mechanically simpler high-lift designs that match the performance of conventional high-lift systems. Finally, technical challenges are identified associated with the application of AFC-enabled highlift systems to modern transonic commercial transports for future technology maturation efforts.

Can a new behaviorally oriented training process to improve lifting technique prevent occupationally related back injuries due to lifting?

Science.gov (United States)

Lavender, Steven A; Lorenz, Eric P; Andersson, Gunnar B J

2007-02-15

A prospective randomized control trial. To determine the degree to which a new behavior-based lift training program (LiftTrainer; Ascension Technology, Burlington, VT) could reduce the incidence of low back disorder in distribution center jobs that require repetitive lifting. Most studies show programs aimed at training lifting techniques to be ineffective in preventing low back disorders, which may be due to their conceptual rather than behavioral learning approach. A total of 2144 employees in 19 distribution centers were randomized into either the LiftTrainer program or a video control group. In the LiftTrainer program, participants were individually trained in up to 5, 30-minute sessions while instrumented with motion capture sensors to quantify the L5/S1 moments. Twelve months following the initial training, injury data were obtained from company records. Survival analyses (Kaplan-Meier) indicated that there was no difference in injury rates between the 2 training groups. Likewise, there was no difference in the turnover rates. However, those with a low (<30 Nm) average twisting moment at the end of the first session experienced a significantly (P < 0.005) lower rate of low back disorder than controls. While overall the LiftTrainer program was not effective, those with twisting moments below 30 Nm reported fewer injuries, suggesting a shift in focus for "safe" lifting programs.

Lambda-Lifting in Quadratic Time

DEFF Research Database (Denmark)

Danvy, Olivier; Schultz, Ulrik Pagh

2002-01-01

Lambda-lifting is a program transformation used in compilers and in partial evaluators and that operates in cubic time. In this article, we show how to reduce this complexity to quadratic time. Lambda-lifting transforms a block-structured program into a set of recursive equations, one for each...... local function in the source program. Each equation carries extra parameters to account for the free variables of the corresponding local function and of all its callees. It is the search for these extra parameters that yields the cubic factor in the traditional formulation of lambda-lifting, which...... is not needed. We therefore simplify the search for extra parameters by treating each strongly connected component instead of each function as a unit, thereby reducing the time complexity of lambda-lifting from O(n 3 log n)toO(n2 log n), where n is the size of the program. Since a lambda-lifter can output...

International conference: nuclear power for the 21 st century

International Nuclear Information System (INIS)

2005-01-01

It is widely recognised that global energy demand will rise substantially during this century. The increased industrialization and urbanization of developing countries will produce large increases in energy demand in regions that currently have very low per capita energy use. This increasing demand for energy will need to be met in order to improve living standards for at least half of the world population and to reduce the economic imbalances between countries and regions. At the same time the use of fossil fuel based energy is identified as a major cause of environmental damage. The release of greenhouse gases from burning of fossil fuel in power stations and for transport is seen as a contributor to global warming. It is widely recognised that continued exploitation of fossil fuels and release of carbon dioxide will need to be controlled. After a prolonged period of slow development of nuclear power, confined to some countries in the world, it is now being recognised that nuclear energy has a potentially significant role to play in meeting the energy needs of the planet without damaging the environment. Developments in technology make the economics of nuclear power more attractive, and they may become even more so as fossil fuel prices continue to rise.or a widespread use of nuclear power, however, there remain concerns on the safety, security, waste and proliferation aspects. The global application of safety standards and appropriate security measures are required to ensure acceptable levels of protection. Effective control measures are required to ensure that non-proliferation commitments are honored. Handling nuclear waste safely and securely is achievable, but continues to remain as a public concern. The broad strategic objectives of the Conference are the following: to review the role of nuclear power and to define the potential benefits (energy security, sustainability and improved environmental protection) that expanding nuclear power offers to meet the

Maximum acceptable weight of lift reflects peak lumbosacral extension moments in a functional capacity evaluation test using free style, stoop and squat lifting.

Science.gov (United States)

Kuijer, P P F M; van Oostrom, S H; Duijzer, K; van Dieën, J H

2012-01-01

It is unclear whether the maximum acceptable weight of lift (MAWL), a common psychophysical method, reflects joint kinetics when different lifting techniques are employed. In a within-participants study (n = 12), participants performed three lifting techniques--free style, stoop and squat lifting from knee to waist level--using the same dynamic functional capacity evaluation lifting test to assess MAWL and to calculate low back and knee kinetics. We assessed which knee and back kinetic parameters increased with the load mass lifted, and whether the magnitudes of the kinetic parameters were consistent across techniques when lifting MAWL. MAWL was significantly different between techniques (p = 0.03). The peak lumbosacral extension moment met both criteria: it had the highest association with the load masses lifted (r > 0.9) and was most consistent between the three techniques when lifting MAWL (ICC = 0.87). In conclusion, MAWL reflects the lumbosacral extension moment across free style, stoop and squat lifting in healthy young males, but the relation between the load mass lifted and lumbosacral extension moment is different between techniques. Tests of maximum acceptable weight of lift (MAWL) from knee to waist height are used to assess work capacity of individuals with low-back disorders. This article shows that the MAWL reflects the lumbosacral extension moment across free style, stoop and squat lifting in healthy young males, but the relation between the load mass lifted and lumbosacral extension moment is different between techniques. This suggests that standardisation of lifting technique used in tests of the MAWL would be indicated if the aim is to assess the capacity of the low back.

33 CFR 118.85 - Lights on vertical lift bridges.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Lights on vertical lift bridges... BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.85 Lights on vertical lift bridges. (a) Lift span lights. The vertical lift span of every vertical lift bridge shall be lighted so that the center of the...

Conference summaries of the Canadian Nuclear Association 30. annual conference, and the Canadian Nuclear Society 11. annual conference

International Nuclear Information System (INIS)

1990-01-01

This volume contains conference summaries for the 30. annual conference of the Canadian Nuclear Association, and the 11. annual conference of the Canadian Nuclear Society. Topics of discussion include: energy needs and challenges facing the Canadian nuclear industry; the environment and nuclear power; the problems of maintaining and developing industrial capacity; the challenges of the 1990's; programmes and issues for the 1990's; thermalhydraulics; reactor physics and fuel management; nuclear safety; small reactors; fuel behaviour; energy production and the environment; computer applications; nuclear systems; fusion; materials handling; and, reactor components

Safety mechanism of a lifting machine

International Nuclear Information System (INIS)

Blaive, D.; Chopinet, E.

1985-01-01

The lifting machine has at least one winch supporting a chain which passes around a chain pulley in a roller block attached to the load. At least one locking mechanism prevents the rotation of the pulley within the block. The locking mechanism can moves between an out-of-operation position and a locking position. A control system includes load sensors associated with the winch sensing the weight of the load acting through the chain. If one part of the chain should break, the load sensors detect this, and the locking mechanism is activated. The invention applies, more particularly, to the handling winches in a fast neutron nuclear power plant [fr

77 FR 20558 - Federal Motor Vehicle Safety Standards; Platform Lifts for Motor Vehicles; Platform Lift...

Science.gov (United States)

2012-04-05

... unrelated to the barrier's safety. Lift-U also questioned the agency's statement that it could be difficult... DEPARTMENT OF TRANSPORTATION National Highway Traffic Safety Administration 49 CFR Part 571 [Docket No. NHTSA-2012-0039] RIN 2127-AJ93 Federal Motor Vehicle Safety Standards; Platform Lifts for...

Fuel Cell Hydroge Manifold for Lift Trucks

DEFF Research Database (Denmark)

Hosseinzadeh, Elham

. Battery driven lift trucks are being used more and more in different companies to reduce their emissions. However, battery driven lift trucks need long time to recharge and may be out of work for a long time. Fuel cell driven lift trucks diminish this problem and are therefore getting more attention...

The third Geneva Conference

Energy Technology Data Exchange (ETDEWEB)

NONE

1964-12-15

Full text: On 31 August 1964, the Third United Nations International Conference on the Peaceful Uses of Atomic Energy (more familiarly known as the 'Third Geneva') was opened at the Palais des Nations in Geneva by the Secretary-General of the United Nations, U Thant. It was somewhat narrower in scope than the previous conferences held in 1935 and 1958, the emphasis being on nuclear power and closely related topics; the conference showed that recent progress in this field had provided more than ample material for a major international gathering. All three conferences have been organized by the United Nations, but on this occasion responsibility for the scientific aspects was delegated to IAEA. The UN Scientific Advisory Committee provided advice and guidance on the scientific side. Under the presidency of Professor V. S. Emelyanov (USSR) the conference sat from 31 August to 9 September, to deal with a programme divided into eight general sessions and 36 technical sessions, for which a total of nearly 750 papers were presented. About 1800 delegates and advisers, representing 75 countries as well as UN agencies, attended; in addition there were some 2000 observers. The central theme of the conference was experience in the construction and operation of power reactors and recent advances in power technology, together with forecasts of future developments. Nuclear fuels and reactor materials, health and safety, waste disposal, and economics of nuclear power figured largely. Technical sessions were devoted to such subjects as the technical and economic aspects of the power reactor systems currently in operation or being built, and the main lines of development towards more advanced systems and development of the fast breeder. Parallel lines of development of alternative systems were also considered - some, such as organic reactors, having already been the subject of extensive trials, while others are in the conceptual stage. 'Package' power plants designed for easy

The third Geneva Conference

International Nuclear Information System (INIS)

1964-01-01

Full text: On 31 August 1964, the Third United Nations International Conference on the Peaceful Uses of Atomic Energy (more familiarly known as the 'Third Geneva') was opened at the Palais des Nations in Geneva by the Secretary-General of the United Nations, U Thant. It was somewhat narrower in scope than the previous conferences held in 1935 and 1958, the emphasis being on nuclear power and closely related topics; the conference showed that recent progress in this field had provided more than ample material for a major international gathering. All three conferences have been organized by the United Nations, but on this occasion responsibility for the scientific aspects was delegated to IAEA. The UN Scientific Advisory Committee provided advice and guidance on the scientific side. Under the presidency of Professor V. S. Emelyanov (USSR) the conference sat from 31 August to 9 September, to deal with a programme divided into eight general sessions and 36 technical sessions, for which a total of nearly 750 papers were presented. About 1800 delegates and advisers, representing 75 countries as well as UN agencies, attended; in addition there were some 2000 observers. The central theme of the conference was experience in the construction and operation of power reactors and recent advances in power technology, together with forecasts of future developments. Nuclear fuels and reactor materials, health and safety, waste disposal, and economics of nuclear power figured largely. Technical sessions were devoted to such subjects as the technical and economic aspects of the power reactor systems currently in operation or being built, and the main lines of development towards more advanced systems and development of the fast breeder. Parallel lines of development of alternative systems were also considered - some, such as organic reactors, having already been the subject of extensive trials, while others are in the conceptual stage. 'Package' power plants designed for easy

Using verbal instructions to influence lifting mechanics - Does the directive "lift with your legs, not your back" attenuate spinal flexion?

Science.gov (United States)

Beach, Tyson A C; Stankovic, Tatjana; Carnegie, Danielle R; Micay, Rachel; Frost, David M

2018-02-01

"Use your legs" is commonly perceived as sound advice to prevent lifting-related low-back pain and injuries, but there is limited evidence that this directive attenuates the concomitant biomechanical risk factors. Body segment kinematic data were collected from 12 men and 12 women who performed a laboratory lifting/lowering task after being provided with different verbal instructions. The main finding was that instructing participants to lift "without rounding your lower back" had a greater effect on the amount of spine flexion they exhibited when lifting/lowering than instructing them to lift "with your legs instead of your back" and "bend your knees and hips". It was concluded that if using verbal instructions to discourage spine flexion when lifting, the instructions should be spine- rather than leg-focused. Copyright © 2017 Elsevier Ltd. All rights reserved.

The 9. European nuclear conference

International Nuclear Information System (INIS)

Maurel, V.; Lewis, D.; Smirnov, V.P.; Gutierrez, J.E.; Paulin, Ph.; Markov, D.V.; Smirnov, A.V.; Polenok, V.S.; Horhoianu, G.; Olteanu, G.; Van der Schaaf, B.; Gavillet, D.; Lapena, J.; Ohms, C.; Roth, A.; Van Dyck, St.; Mardon, J.P.; Thomas, A.; Cipiere, M.F.; Faidy, C.; Hedin, F.; Delnondedieu, M.; Chassignole, B.; Doudet, L.; Dupond, O.; Kang, K.; Park, K.; Kim, K.; Ha, J.; Hoon-Seok, Jung; Yong-koo, Lee; Kwang-Ho, Kim; Seungwoo, Paek; Heui-Joo, Choi; Do-Hee, Ahn; Kwang-Rag, Kim; Minsoo, Lee; Sung-Paal, Yim; Hongsuk, Chung; Detroux, P.; Meessen, O.; Defloor, J.; Lars-Erik, Holm; Barescut, J.C.; Vacquier, B.; Laurier, D.; Caer, S.; Quesne, B.; Oudalova, A.; Geras'kin, St.; Dikarev, V.; Dikareva, N.; Chernonog, E.; Yang-Geun, Chung; Gab-Bock, Lee; Sun-Young, Bang; Yong-Sun, Lee; Bolognese-Milsztajn, T.; Frank, D.; Lacoste, V.; Pihet, P.; Lacronique, J.F.; Chauliac, C.; Verwaerde, D.; Pavageau, O.; Zaetta, A.; Varaine, F.; Warin, D.; Hudelot, J.P.; Bioux, Ph.; Klann, R.; Petruzzi, A.; D'auria, F.; Yung Kwon, Jin; Chul Jin, Chol; Mihalache, M.; Radu, V.; Pavelescu, M.; Schneidesch, Ch.R.; Jinzhao, Zhang; Dalleur, J.P.; Nuttin, A.; Meplan, O.; Wilson, J.; Perdu, F.; Campioni, G.; Mounier, C.; Sigrist, J.F.; Laine, Ch.; Broc, D.; Robbe, M.F.; Cariou, Y.; Seok-Kyun, Yoon; Win, Naing; Myung-Hyun, Kim; Kyung, Hee; Fridman, E.; Shwageraus, E.; Galperin, A.; Meplan, O.; Laulan, O.; Mechel-Sendis, F.; Belgaid, M.; Kadem, F.; Amokrane, A.; Hamidouche, T.; El-Khider, Si-Ahmed

2005-01-01

This issue gathers the abstracts of the papers presented at the ninth European nuclear conference (ENC-2005). The main part of the conference is split into 20 sessions. These sessions cover all technical aspects of nuclear power, from reactor design to waste management, without forgetting experimental and research reactors, reactor dismantling, economy, resources, safety, radioprotection and education issues. Perspectives of a nuclear renaissance are clearly visible in the world. This renaissance, mainly due to political, economical, societal and ecological factors, is fuelled by scientific and technical progress. This conference was the opportunity to present together these aspects of nuclear power and to analyze their mutual interactions

Visual perception of fatigued lifting actions.

Science.gov (United States)

Fischer, Steven L; Albert, Wayne J; McGarry, Tim

2012-12-01

Fatigue-related changes in lifting kinematics may expose workers to undue injury risks. Early detection of accumulating fatigue offers the prospect of intervention strategies to mitigate such fatigue-related risks. In a first step towards this objective, this study investigated whether fatigue detection was accessible to visual perception and, if so, what was the key visual information required for successful fatigue discrimination. Eighteen participants were tasked with identifying fatigued lifts when viewing 24 trials presented using both video and point-light representations. Each trial comprised a pair of lifting actions containing a fresh and a fatigued lift from the same individual presented in counter-balanced sequence. Confidence intervals demonstrated that the frequency of correct responses for both sexes exceeded chance expectations (50%) for both video (68%±12%) and point-light representations (67%±10%), demonstrating that fatigued lifting kinematics are open to visual perception. There were no significant differences between sexes or viewing condition, the latter result indicating kinematic dynamics as providing sufficient information for successful fatigue discrimination. Moreover, results from single viewer investigation reported fatigue detection (75%) from point-light information describing only the kinematics of the box lifted. These preliminary findings may have important workplace applications if fatigue discrimination rates can be improved upon through future research. Copyright © 2012 Elsevier B.V. All rights reserved.

Project LIFT: Year 1 Report

Science.gov (United States)

Norton, Michael; Piccinino, Kelly

2014-01-01

Research for Action (RFA) is currently in the second year of a five-year external evaluation of the Project Leadership and Investment for Transformation (LIFT) Initiative in the Charlotte-Mecklenburg School District (CMS). Project LIFT is a public-private partnership between CMS and the local philanthropic and business communities in Charlotte,…

Liebherr lifts off with east coast projects

Energy Technology Data Exchange (ETDEWEB)

Anon

2004-11-01

Liebherr is one of the world's leading manufacturers of construction machinery, and is the supplier of technically-innovative user-oriented products and services not only to the oil industry but also to other industries using heavy lifting equipment. The Newfoundland and Labrador offshore oil and gas sector has been a special springboard of success for the company; they have seven offshore cranes working on three installations, and as the White Rose floating production vessel sails to the Grand Banks in 2005, the number will increase to nine. The other cranes are on the Hibernia platform, the Terra Nova FPSO, and the Henry Goodrich drilling rig. Two of the cranes on the Terra Nova FPSO have a lift capacity of 40 tons, while a third crane mounted at the rear of the vessel has a 20 ton capacity. They are capable of performing loading operations in seas as high as three metres. These cranes are powerful, compact and maneuverable, and feature ultra-modern mobile crane technology that satisfies combined road and off-road operating requirements on construction sites of all kinds. 2 photos.

Sensorimotor memory biases weight perception during object lifting

Directory of Open Access Journals (Sweden)

Vonne evan Polanen

2015-12-01

Full Text Available When lifting an object, the brain uses visual cues and an internal object representation to predict its weight and scale fingertip forces accordingly. Once available, tactile information is rapidly integrated to update the weight prediction and refine the internal object representation. If visual cues cannot be used to predict weight, force planning relies on implicit knowledge acquired from recent lifting experience, termed sensorimotor memory. Here, we investigated whether perception of weight is similarly biased according to previous lifting experience and how this is related to force scaling. Participants grasped and lifted series of light or heavy objects in a semi-randomized order and estimated their weights. As expected, we found that forces were scaled based on previous lifts (sensorimotor memory and these effects increased depending on the length of recent lifting experience. Importantly, perceptual weight estimates were also influenced by the preceding lift, resulting in lower estimations after a heavy lift compared to a light one. In addition, the weight estimations were negatively correlated with the magnitude of planned force parameters. This perceptual bias was only found if the current lift was light, but not heavy since the magnitude of sensorimotor memory effects had, according to Weber’s law, relatively less impact on heavy compared to light objects. A control experiment tested the importance of active lifting in mediating these perceptual changes and showed that when weights are passively applied on the hand, no effect of previous sensory experience is found on perception. These results highlight how fast learning of novel object lifting dynamics can shape weight perception and demonstrate a tight link between action planning and perception control. If predictive force scaling and actual object weight do not match, the online motor corrections, rapidly implemented to downscale forces, will also downscale weight estimation in

Facilitating Learning at Conferences

DEFF Research Database (Denmark)

Ravn, Ib; Elsborg, Steen

2011-01-01

The typical conference consists of a series of PowerPoint presentations that tend to render participants passive. Students of learning have long abandoned the transfer model that underlies such one-way communication. We propose an al-ternative theory of conferences that sees them as a forum...... for learning, mutual inspiration and human flourishing. We offer five design principles that specify how conferences may engage participants more and hence increase their learning. In the research-and-development effort reported here, our team collaborated with conference organizers in Denmark to introduce...... and facilitate a variety of simple learning techniques at thirty one- and two-day conferences of up to 300 participants each. We present ten of these techniques and data evaluating them. We conclude that if conference organizers allocate a fraction of the total conference time to facilitated processes...

Breast lift

Science.gov (United States)

... and areola may be moved. Sometimes, women have breast augmentation (enlargement with implants) when they have a breast lift. Why the ... MD, FACS, general surgery practice specializing in breast cancer, Virginia Mason Medical Center, Seattle, WA. Also reviewed ...

Lower complexity bounds for lifted inference

DEFF Research Database (Denmark)

Jaeger, Manfred

2015-01-01

instances of the model. Numerous approaches for such “lifted inference” techniques have been proposed. While it has been demonstrated that these techniques will lead to significantly more efficient inference on some specific models, there are only very recent and still quite restricted results that show...... the feasibility of lifted inference on certain syntactically defined classes of models. Lower complexity bounds that imply some limitations for the feasibility of lifted inference on more expressive model classes were established earlier in Jaeger (2000; Jaeger, M. 2000. On the complexity of inference about...... that under the assumption that NETIME≠ETIME, there is no polynomial lifted inference algorithm for knowledge bases of weighted, quantifier-, and function-free formulas. Further strengthening earlier results, this is also shown to hold for approximate inference and for knowledge bases not containing...

Lifting devices in nuclear facilities

International Nuclear Information System (INIS)

The rule is valid for lifts, cranes, winches, rail travel trolleys, load lifting devices and fuel element changing devices for light-water reactors, insofar as these are used in plants to produce or to fission nuclear fuels or to process irradiated nuclear fuels or in the storage or other use of nuclear fuels. (LH) [de

Sikkerhedsbestemmelser for beskæringsarbejde fra lift

DEFF Research Database (Denmark)

Jakobsen, Ole Sejr; Theilby, Frans

2010-01-01

Brug af lift til beskæring og fældning af træer er blevet udbredt i den grønne sektor. Som bruger er det vigtigt at kende den lift, man har valgt, og at arbejdet med motorsav foregår efter Arbejdstilsynets regler og anbefalinger.......Brug af lift til beskæring og fældning af træer er blevet udbredt i den grønne sektor. Som bruger er det vigtigt at kende den lift, man har valgt, og at arbejdet med motorsav foregår efter Arbejdstilsynets regler og anbefalinger....

Effect of training and lifting equipment for preventing back pain in lifting and handling: systematic review

NARCIS (Netherlands)

Martimo, Kari-Pekka; Verbeek, Jos; Karppinen, Jaro; Furlan, Andrea D.; Takala, Esa-Pekka; Kuijer, P. Paul F. M.; Jauhiainen, Merja; Viikari-Juntura, Eira

2008-01-01

To determine whether advice and training on working techniques and lifting equipment prevent back pain in jobs that involve heavy lifting. Medline, Embase, CENTRAL, Cochrane Back Group's specialised register, CINAHL, Nioshtic, CISdoc, Science Citation Index, and PsychLIT were searched up to

Occupational lifting and pelvic pain during pregnancy:

DEFF Research Database (Denmark)

Larsen, Pernille Stemann; Strandberg-Larsen, Katrine; Juhl, Mette

2013-01-01

OBJECTIVES: Pelvic pain during pregnancy is a common ailment, and the disease is a major cause of sickness absence during pregnancy. It is plausible that occupational lifting may be a risk factor of pelvic pain during pregnancy, but no previous studies have examined this specific exposure. The aim...... of this study was to examine the association between occupational lifting and pelvic pain during pregnancy. METHODS: The study comprised 50 143 pregnant women, enrolled in the Danish National Birth Cohort in the period from 1996-2002. During pregnancy, the women provided information on occupational lifting...... (weight load and daily frequency), and six months post partum on pelvic pain. Adjusted odds ratios for pelvic pain during pregnancy according to occupational lifting were calculated by logistic regression. RESULTS: Any self-reported occupational lifting (>1 time/day and loads weighing >10 kg...

Non-electric applications of nuclear power: Seawater desalination, hydrogen production and other industrial applications. Proceedings of an international conference

International Nuclear Information System (INIS)

2009-01-01

interest in the non-electric applications of nuclear power based on future generation advanced and innovative nuclear reactors. The IAEA organized a Symposium on Nuclear Desalination of Seawater hosted by Korean Atomic Energy Research Institute in Taejon, South Korea in 1997. IAEA cooperated with World Council of Nuclear Workers (WONUC) and the Moroccan Association of Nuclear Engineers (AIGAM) on an International Conference on Nuclear Desalination held at Marrakesh in 2002. In view of the widened scope of the Agency's programme, it was proposed to hold the next International Conference in 2007 on Non-electric Applications of Nuclear Power. The objective of the conference was to share the experiences of Member States already engaged in the development programme in this area with those having interest and considering research studies. This conference, held April 16-19, 2007 at JAEA, Oarai, Japan, covered various aspects of non-electric applications of nuclear power utilizing combined heat and power (CHP). The major focus was on desalination, hydrogen production or other fuel production as a complement to CO 2 -free energy sources and many newer industrial applications. This publication contains the text of all the contributory papers, summary of the sessions and the panel discussion at the conference. The proceeding will be useful to the scientists and engineers interested in research and development of the non-electric applications of nuclear power worldwide

Conceptual design and issues of the laser inertial fusion test (LIFT) reactor—targets and chamber systems

Science.gov (United States)

Norimatsu, T.; Kozaki, Y.; Shiraga, H.; Fujita, H.; Okano, K.; Members of LIFT Design Team

2017-11-01

We present the conceptual design of an experimental laser fusion plant known as the laser inertial fusion test (LIFT) reactor. The conceptual design aims at technically connecting a single-shot experiment and a commercial power plant. The LIFT reactor is designed on a three-phase scheme, where each phase has specific goals and the dedicated chambers of each phase are driven by the same laser. Technical issues related to the chamber technology including radiation safety to repeat burst mode operation are discussed in this paper.

Maximum Acceptable Weight of Lift reflects peak lumbosacral extension moments in a Functional Capacity Evaluation test using free style, stoop, and squat lifting

NARCIS (Netherlands)

Kuijer, P.P.F.M.; van Oostrom, S.H.; Duijzer, K.; van Dieen, J.H.

2012-01-01

It is unclear whether the maximum acceptable weight of lift (MAWL), a common psychophysical method, reflects joint kinetics when different lifting techniques are employed. In a within-participants study (n = 12), participants performed three lifting techniques - free style, stoop and squat lifting

Maximum acceptable weight of lift reflects peak lumbosacral extension moments in a functional capacity evaluation test using free style, stoop and squat lifting

NARCIS (Netherlands)

Kuijer, P. P. F. M.; van Oostrom, S. H.; Duijzer, K.; van Dieën, J. H.

2012-01-01

It is unclear whether the maximum acceptable weight of lift (MAWL), a common psychophysical method, reflects joint kinetics when different lifting techniques are employed. In a within-participants study (n = 12), participants performed three lifting techniques - free style, stoop and squat lifting

Back injury prevention: a lift team success story.

Science.gov (United States)

Hefti, Kelly S; Farnham, Richard J; Docken, Lisa; Bentaas, Ruth; Bossman, Sharon; Schaefer, Jill

2003-06-01

Work related back injuries among hospital personnel account for high volume, high cost workers' compensation claims. These injuries can be life altering experiences, affecting both the personal and professional lives of injured workers. Lifting must be viewed as a skill involving specialized training and mandated use of mechanical equipment, rather than as a random task performed by numerous health care providers. The use of a lift team specially trained in body mechanics, lifting techniques, and the use of mandated mechanical equipment can significantly affect injury data, financial outcomes, and employee satisfaction. The benefits of a lift team extend beyond the effect on injury and financial outcomes--they can be used for recruitment and retention strategies, and team members serve as mentors to others by demonstrating safe lifting techniques. Ultimately, a lift team helps protect a valuable resource--the health care worker.

Containment vessel bottom head transport and lifting technique

International Nuclear Information System (INIS)

Zheng Donghong; Tian Shiyong; Hu Dequan; Xiao Hongtao

2013-01-01

The challengeable transport and lifting techniques and high safety assurance measures are needed for the onsite construction of the AP1000 containment vessel bottom head (CVBH), which is a large component with heavy weight, big size, high center of gravity, and easy to deformation. During transport, the infra structural road foundation is heavily loaded with big turning radius, and the requirement for synchronization of transport vehicles is strict. During lifting, the crane lifting capacities are high, requirement for the lifting and rigging tools is strict, nuclear island being put into place is difficult, and the crane operating foundation is heavily loaded. The transport and lifting techniques and safety assurance measures for CVBH are elaborated in detail, so as to provide a reference for the follow-up transport and lifting of large components of nuclear island. (authors)

Collection of articles of the 5-th Conference of the Ukrainian Nuclear Society 'Youth to nuclear power'

International Nuclear Information System (INIS)

Barbashev, S.V.

2001-01-01

Large scope of problems is presented. Operation of nuclear power enterprises, introduction of safety culture principles in them, situation with the training of specialists, role of youth in nuclear fuel complex and others are discussed. Reports of participants which were submitted at the conference are presented

Annual conference on nuclear technology. Nuclear power 2001: option for the future

International Nuclear Information System (INIS)

Anon.

2001-01-01

The Dresden Palace for Culture was the venue of the ANNUAL MEETING ON NUCLEAR TECHNOLOGY on May 15-17, 2001, the first to be held in Dresden and the first also to be held in one of the new German federal states. Although no nuclear plant is in operation in East Germany after the Greifswald Nuclear Power Station was decommissioned, nuclear technology continues to play an important role especially in research and university teaching in this part of Germany. The organizers of the conference, Deutsches Atomforum e.V. (DAtF) and Kerntechnische Gesellschaft e.V. (KTG), welcomed more than 1000 participants from nineteen countries. The three-day program, with its traditional, proven structure, featured plenary sessions on the first day, and specialized sessions, technical sessions, poster sessions, and other events on the following days. The partner country at the Annual Meeting on Nuclear Technology was Russia, with a session specially devoted to selected topics of the country. The conference was accompanied by a technical exhibition with company meeting points of vendors, suppliers, and service industries. A video film forum was arranged for the interested public which featured contributions about nuclear research, nuclear power plant operation, transport and storage as well as decommissioning. Another major event was a workshop on 'Preserving Competence in Nuclear Technology'. The plenary day is described in this summary report, while the results of the technical sessions as seen by the rapporteurs are printed elsewhere in this issue of atw 8/9, 2001. (orig.) [de

New F-theory lifts

International Nuclear Information System (INIS)

Collinucci, Andres

2009-01-01

In this note, a procedure is developed to explicitly construct non-trivial F-theory lifts of perturbative IIB orientifold models on Calabi-Yau complete intersections in toric varieties. This procedure works on Calabi-Yau orientifolds where the involution coordinate can have arbitrary projective weight, as opposed to the well-known hypersurface cases where it has half the weight of the equation defining the CY threefold. This opens up the possibility of lifting more general setups, such as models that have O3-planes.

Opening remarks at the International Conference on Human Resource Development for Introducing and Expanding Nuclear Power Programmes

International Nuclear Information System (INIS)

Klein, D.E.

2010-03-01

The topic of this conference - human resources development and the expansion of nuclear power - is about the commitment and investment in people. The importance of this 'human side' of modern technology is sometimes forgotten or assumed to develop on its own once basic educational programs and institutions are put in place. In my view, the development and maintenance of a skilled national workforce is critical to the development of a stable, successful national nuclear power program

ELMIA Energy and Future 88. Conference E5. Nuclear power phaseout and storage of nuclear waste

International Nuclear Information System (INIS)

1988-01-01

The conference comprised lectures on the following subjects: - How to maintain availability, quality and safety during the phaseout period to the year 2010. - Demolition of nuclear power plants. - Storage of nuclear waste. - Estimate of risks in a long perspective. - Financing of the phaseout. Separate abstracts were prepared for four sections of this report. (O.S.)

Relative importance of expertise, lifting height and weight lifted on posture and lumbar external loading during a transfer task in manual material handling.

Science.gov (United States)

Plamondon, André; Larivière, Christian; Delisle, Alain; Denis, Denys; Gagnon, Denis

2012-01-01

The objective of this study was to measure the effect size of three important factors in manual material handling, namely expertise, lifting height and weight lifted. The effect of expertise was evaluated by contrasting 15 expert and 15 novice handlers, the effect of the weight lifted with a 15-kg box and a 23-kg box and the effect of lifting height with two different box heights: ground level and a 32 cm height. The task consisted of transferring a series of boxes from a conveyor to a hand trolley. Lifting height and weight lifted had more effect size than expertise on external back loading variables (moments) while expertise had low impact. On the other hand, expertise showed a significant effect of posture variables on the lumbar spine and knees. All three factors are important, but for a reduction of external back loading, the focus should be on the lifting height and weight lifted. The objective was to measure the effect size of three important factors in a transfer of boxes from a conveyor to a hand trolley. Lifting height and weight lifted had more effect size than expertise on external back loading variables but expertise was a major determinant in back posture.

Maximum Acceptable Weight of Lift reflects peak lumbosacral extension moments in a Functional Capacity Evaluation test using free style, stoop, and squat lifting

OpenAIRE

Kuijer, P.P.F.M.; van Oostrom, S.H.; Duijzer, K.; van Dieen, J.H.

2012-01-01

It is unclear whether the maximum acceptable weight of lift (MAWL), a common psychophysical method, reflects joint kinetics when different lifting techniques are employed. In a within-participants study (n = 12), participants performed three lifting techniques - free style, stoop and squat lifting from knee to waist level - using the same dynamic functional capacity evaluation lifting test to assess MAWL and to calculate low back and knee kinetics. We assessed which knee and back kinetic para...

The Innovative Design and Prototype Verification of Wheelchair with One Degree of Freedom to Perform Lifting and Standing Functions

Science.gov (United States)

Hsieh, Long-Chang; Chen, Tzu-Hsia

2017-12-01

Traditionally, the mechanism of wheelchair with lifting and standing functions has 2 degrees of freedom, and used 2 power sources to perform these 2 motion function. The purpose of this paper is to invent new wheelchair with 1 degree of freedom to perform these 2 motion functions. Hence, we can use only 1 power source to drive the mechanism to achieve lifting and standing motion functions. The new design has the advantages of simple operation, more stability, and more safety. For traditional standing wheelchair, its’ centre of gravity moves forward when standing up and it needs 2 auxiliary wheels to prevent dumping. In this paper, by using the checklist method of Osborn, the wheelchair with 1 DOF is invented to perform lifting and standing functions. The centre of gravity of this new wheelchair after standing up still located between the front and rear wheels, no auxiliary wheels needed. Finally, the prototype is manufactured to verify the theoretical results.

Environmental impact of nuclear power plants. Proceedings of a conference held November 26-30, 1974, in Atlanta, Georgia

International Nuclear Information System (INIS)

Karam, R.A.; Morgan, K.Z.

1976-01-01

This conference served as a forum for experts, power industry executives and engineers, and Federal and state agencies' representatives to discuss and exchange information on the environmental effects of nuclear power plants. An objective of this meeting was to identify the necessary elements and legal requirements for environmental impact statements. Twenty-three papers were presented in six sessions: Plant Site Selection; Ecology; Radioactive Waste and Thermal Pollution; Standards and Guidelines in the Preparation of Environmental Impact Statements; Cost-Benefit Analysis; and Environmental Impact Studies of Various Power Reactors

Development of High-Efficiency Low-Lift Vapor Compression System - Final Report

Energy Technology Data Exchange (ETDEWEB)

Katipamula, Srinivas; Armstrong, Peter; Wang, Weimin; Fernandez, Nicholas; Cho, Heejin; Goetzler, W.; Burgos, J.; Radhakrishnan, R.; Ahlfeldt, C.

2010-03-31

PNNL, with cofunding from the Bonneville Power Administration (BPA) and Building Technologies Program, conducted a research and development activity targeted at addressing the energy efficiency goals targeted in the BPA roadmap. PNNL investigated an integrated heating, ventilation and air conditioning (HVAC) system option referred to as the low-lift cooling system that potentially offers an increase in HVAC energy performance relative to ASHRAE Standard 90.1-2004.

The Cumulative Lifting Index (CULI) for the Revised NIOSH Lifting Equation: Quantifying Risk for Workers With Job Rotation.

Science.gov (United States)

Garg, Arun; Kapellusch, Jay M

2016-08-01

The objectives were to: (a) develop a continuous frequency multiplier (FM) for the Revised NIOSH Lifting Equation (RNLE) as a function of lifting frequency and duration of a lifting task, and (b) describe the Cumulative Lifting Index (CULI), a methodology for estimating physical exposure to workers with job rotation. The existing FM for the RNLE (FME) does not differentiate between task duration >2 hr and <8 hr, which makes quantifying physical exposure to workers with job rotation difficult and presents challenges to job designers. Using the existing FMs for 1, 2, and 8 hr of task durations, we developed a continuous FM (FMP) that extends to 12 hr per day. We simulated 157,500 jobs consisting of two tasks each and, using different combinations of Frequency Independent Lifting Index, lifting frequency and duration of lifting. Biomechanical stresses were estimated using the CULI, time-weighted average (TWA), and peak exposure. The median difference between FME and FMP was ±1% (range: 0%-15%). Compared to CULI, TWA underestimated risk of low-back pain (LBP) for 18% to 30% of jobs, and peak exposure for an assumed 8-hr work shift overestimated risk of LBP for 20% to 25% of jobs. Peak task exposure showed 90% agreement with CULI but ignored one of two tasks. The CULI partially addressed the underestimation of physical exposure using the TWA approach and overestimation of exposure using the peak-exposure approach. The proposed FM and CULI may provide more accurate physical exposure estimates, and therefore estimated risk of LBP, for workers with job rotation. © 2016, Human Factors and Ergonomics Society.

Low-back loading in lifting two loads beside the body compared to lifting one load in front of the body

NARCIS (Netherlands)

Faber, G.S.; Kingma, I.; Bakker, A.J.; van Dieen, J.H.

2009-01-01

Low-back load during manual lifting is considered an important risk factor for the occurrence of low-back pain. Splitting a load, so it can be lifted beside the body (one load in each hand), instead of in front of the body, can be expected to reduce low-back load. Twelve healthy young men lifted 10

Ontogeny of lift and drag production in ground birds.

Science.gov (United States)

Heers, Ashley M; Tobalske, Bret W; Dial, Kenneth P

2011-03-01

The juvenile period is often a crucial interval for selective pressure on locomotor ability. Although flight is central to avian biology, little is known about factors that limit flight performance during development. To improve understanding of flight ontogeny, we used a propeller (revolving wing) model to test how wing shape and feather structure influence aerodynamic performance during development in the precocial chukar partridge (Alectoris chukar, 4 to >100 days post hatching). We spun wings in mid-downstroke posture and measured lift (L) and drag (D) using a force plate upon which the propeller assembly was mounted. Our findings demonstrate a clear relationship between feather morphology and aerodynamic performance. Independent of size and velocity, older wings with stiffer and more asymmetrical feathers, high numbers of barbicels and a high degree of overlap between barbules generate greater L and L:D ratios than younger wings with flexible, relatively symmetrical and less cohesive feathers. The gradual transition from immature feathers and drag-based performance to more mature feathers and lift-based performance appears to coincide with ontogenetic transitions in locomotor capacity. Younger birds engage in behaviors that require little aerodynamic force and that allow D to contribute to weight support, whereas older birds may expand their behavioral repertoire by flapping with higher tip velocities and generating greater L. Incipient wings are, therefore, uniquely but immediately functional and provide flight-incapable juveniles with access to three-dimensional environments and refugia. Such access may have conferred selective advantages to theropods with protowings during the evolution of avian flight.

Pig lift applications in offshore dry completion wells; Aplicacao do pig lift em pocos offshore de completacao seca

Energy Technology Data Exchange (ETDEWEB)

Lima, Paulo C.R.; Faria, Rogerio Costa; Almeida, Alcino Resende [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

2000-07-01

Production increases of 10% to 130% have been obtained with pig lift installations on offshore oil wells in the Cacao Field, southeast Brazil. At the present time 3 wells out of 5 are being produced with pig lift. These deep, highly deviated wells with little space on the platform to the required surface equipment presented a challenge to pig lift technology. However, these difficulties were overcame and the benefits obtained helped to maintain the economical attractiveness of the platform. (author)

A Practical Approach To Lift-Off

Science.gov (United States)

Jones, Susan K.; Chapman, Richard C.; Pavelchek, Edward K.

1987-08-01

Lift-off technology provides an alternate metal patterning technology to that of subtractive etching. In this raper, we describe an image reversal process which provides a practical means for reliably producing resist stencils which are required for successful lift-off in a 2.0 μm metal pitch CMOS process, as well as for experimental submicron processing. Experimental data and PROSIM simulations are presented to show the effects of patterning exposure dose, flood exposure dose, develop time, and focus parameters on resist linewidths as well as for control of resist retrograde (undercut) sidewall angles. Deposition and subsequent lift-off of Al/Cu alloys and sandwich metallizations is demonstrated. Because the image reversal process enables pattern definition at the top of the resist film, it is demonstrated that thicker resist films can be used to produce finer resolution of lift-off stencils over topography than would have been expected without resorting to multilayer resist structures.

Nuclear power plant conference 2010 (NPC 2010): International conference on water chemistry of nuclear reactor systems and 8th International radiolysis, electrochemistry and materials performance workshop

International Nuclear Information System (INIS)

2010-01-01

The Nuclear Plant Chemistry Conference was held in Quebec City, Quebec, Canada on October 3-7, 2010. It was hosted by the Canadian Nuclear Society and was held in Canada for the first time. This international event hosted over 300 attendees, two thirds from outside of Canada, mostly from Europe and and Far East. The conference is formally known as the International Conference on Water Chemistry of Nuclear Reactor Systems and is the 15th of a series that began in 1977 in Bournemouth, UK. The conference focussed on the latest developments in the science and technology of water chemistry control in nuclear reactor systems. Utility scientists, engineers and operations people met their counterparts from research institutes, service organizations and universities to address the challenges of chemistry control and degradation management of their complex and costly plants for the many decades that they are expected to operate. Following the four day conference, the 8th International Radiolysis, Electrochemistry and Materials Performance Workshop was held as associated, but otherwise free-standing event on Friday, October 8, 2010. It was also well attended and the primary focus was the effect of radiation on corrosion. When asked about the importance of chemistry in operating nuclear power plants, the primary organizers summarized it in the following statement: 'Once a nuclear plant is in operation, chemistry improvement is the only way to increase the longevity of the plant and its equipment'. The organisers of the 2010 Workshop and the NPC 2010 conference decided that these two events would be held consecutively, as previous, but for the first time the organization and registration would be shared, which proved to be a winning combination by the attendance.

Book of abstracts. Fifteenth Pacific basin nuclear conference

International Nuclear Information System (INIS)

2006-10-01

The 15 th Pacific Basic Nuclear Conference (PBNC) was held in Sydney, Australia.This conference is the first large international conference in nuclear field held in Australia. The 9 th conference in this series was hosted in Sydney in 1994 by the Australian Nuclear Association in a joint venture with The Institution of Engineers Australia (now known as Engineers Australia). The present conference is the 15 th in the series and is also hosted by the Australian Nuclear Association and Engineers Australia. The 16 th conference will be hosted in Japan in October 2008. Australia has abundant resources of uranium and thorium and is an important supplier of uranium to the world's nuclear power stations under strict safeguards agreements. In this conference an extensive range of papers on all aspects of nuclear power and the nuclear fuel cycle were presented. The theme for 15PBNC is a Pacific Nuclear Future: Nuclear Science and Engineering for a Sustainable Society . Abstracts from over 240 papers and 50 posters have been reviewed and accepted in the eight major topic areas: nuclear power; nuclear technology and development; nuclear fuel cycle; safety and regulation; research reactors and applications; nuclear medicine; non proliferation and safeguards; and public information and education. This conference would further promote the wide exchange and cooperation in nuclear technical application areas among international countries

A parallel 3-D discrete wavelet transform architecture using pipelined lifting scheme approach for video coding

Science.gov (United States)

Hegde, Ganapathi; Vaya, Pukhraj

2013-10-01

This article presents a parallel architecture for 3-D discrete wavelet transform (3-DDWT). The proposed design is based on the 1-D pipelined lifting scheme. The architecture is fully scalable beyond the present coherent Daubechies filter bank (9, 7). This 3-DDWT architecture has advantages such as no group of pictures restriction and reduced memory referencing. It offers low power consumption, low latency and high throughput. The computing technique is based on the concept that lifting scheme minimises the storage requirement. The application specific integrated circuit implementation of the proposed architecture is done by synthesising it using 65 nm Taiwan Semiconductor Manufacturing Company standard cell library. It offers a speed of 486 MHz with a power consumption of 2.56 mW. This architecture is suitable for real-time video compression even with large frame dimensions.

Control of propulsion and body lift during the first two stances of sprint running: a simulation study.

Science.gov (United States)

Debaere, Sofie; Delecluse, Christophe; Aerenhouts, Dirk; Hagman, Friso; Jonkers, Ilse

2015-01-01

The aim of this study was to relate the contribution of lower limb joint moments and individual muscle forces to the body centre of mass (COM) vertical and horizontal acceleration during the initial two steps of sprint running. Start performance of seven well-trained sprinters was recorded using an optoelectronic motion analysis system and two force plates. Participant-specific torque-driven and muscle-driven simulations were conducted in OpenSim to quantify, respectively, the contributions of the individual joints and muscles to body propulsion and lift. The ankle is the major contributor to both actions during the first two stances, with an even larger contribution in the second compared to the first stance. Biarticular gastrocnemius is the main muscle contributor to propulsion in the second stance. The contribution of the hip and knee depends highly on the position of the athlete: During the first stance, where the athlete runs in a forward bending position, the knee contributes primarily to body lift and the hip contributes to propulsion and body lift. In conclusion, a small increase in ankle power generation seems to affect the body COM acceleration, whereas increases in hip and knee power generation tend to affect acceleration less.

Waste Package Lifting Calculation

International Nuclear Information System (INIS)

H. Marr

2000-01-01

The objective of this calculation is to evaluate the structural response of the waste package during the horizontal and vertical lifting operations in order to support the waste package lifting feature design. The scope of this calculation includes the evaluation of the 21 PWR UCF (pressurized water reactor uncanistered fuel) waste package, naval waste package, 5 DHLW/DOE SNF (defense high-level waste/Department of Energy spent nuclear fuel)--short waste package, and 44 BWR (boiling water reactor) UCF waste package. Procedure AP-3.12Q, Revision 0, ICN 0, calculations, is used to develop and document this calculation

Null lifts and projective dynamics

Energy Technology Data Exchange (ETDEWEB)

Cariglia, Marco, E-mail: marco@iceb.ufop.br

2015-11-15

We describe natural Hamiltonian systems using projective geometry. The null lift procedure endows the tangent bundle with a projective structure where the null Hamiltonian is identified with a projective conic and induces a Weyl geometry. Projective transformations generate a set of known and new dualities between Hamiltonian systems, as for example the phenomenon of coupling-constant metamorphosis. We conclude outlining how this construction can be extended to the quantum case for Eisenhart–Duval lifts.

Weight Training for Strength and Power.

Science.gov (United States)

President's Council on Physical Fitness and Sports, Washington, DC.

This paper begins by defining the terms "weight training,""weight lifting,""strength,""power," and "muscular endurance.""Weight training" is differentiated from "weight lifting" and defined as a systematic series of resistance exercises designed to promote physical development and conditioning or to rehabilitate persons who have suffered injury or…

'Natural Gas lift', a New Tool for Nigeria

International Nuclear Information System (INIS)

Lucas, C. D.

2003-01-01

Gas lift is the most common means of artificial lift in the Niger Delta and has been widely applied worldwide. The advent of remote monitoring and control devises (RMC) has added a new option in artificiallift, 'natural gas lift'. 'Natural gas lift' is an extension RMC in which a gas zone and one or more oil zones are produced through the same tubing string, using the gas enhance the production of the oil zones. The flow of gas is maintained in the optimal range using down hole chokes that are controlled from the surface. The gas flow rate is monitored using downhole pressure and .temperature gauges. The use of 'natural gas lift' has the advantages of gas lift but without the cost associated with gas lift; gas supply wells, compression etc. This is especially critical in areas that are remote from other facilities or in subsea completions where access to the wells is limited. Stacked reservoirs and frequent inclusion of both oil and gas reservoirs in the same field, as found in the Niger Delta, makes Nigeria a prime candidate for this technology. An example of this production from the North Sea will be presented along with a potential application using data from the Niger Delta. Design elements of the monitoring and control systems will be covered and the advantages and drawbacks of this application will be discussed

The learning conference

DEFF Research Database (Denmark)

Ravn, Ib

little support amongst serious students of learning. The professional conference as a forum for knowledge sharing is in dire need of a new learning theory and a more enlightened practice. The notion of human flourishing is offered as basis for theory, and four simple design principles for the so......The typical one-day conference attended by managers or professionals in search of inspiration is packed with PowerPoint presentations and offers little opportunity for involvement or knowledge sharing. Behind the conventional conference format lurks the transfer model of learning, which finds......-called “learning conference” are proposed: People go to conferences to 1. get concise input, 2. interpret it in the light of their ongoing concerns, 3. talk about their current projects and 4. meet the other attendees and be inspired by them. Six practical techniques that induce attendees to do these things...

The Design of Wheelchair Lifting Mechanism and Control System

Institute of Scientific and Technical Information of China (English)

ZHAO Cong; WANG Zheng-xing; JIANG Shi-hong; ZHANG Li; LIU Zheng-yu

2014-01-01

In order to achieve a wheelchair lift function, this paper designs a tri-scissors mechanism. Through the so-called H-type transmission and L-type swing rod, the three scissors mechanisms lift in the same rate with only one liner motor while ensuring the stability of the lift. Finite element analysis in ANSYS is performed to verify the material strength. The control system with Sunplus SCM achieves the voice control of wheelchair walking and lifting.

Isolated neck-lifting procedure: isolated stork lift.

Science.gov (United States)

Barbarino, Sheila C; Wu, Allan Y; Morrow, David M

2013-04-01

Many patients desire cosmetic improvement of neck laxity when consulting with a plastic surgeon about their face. Neck laxity and loss of the cervicomental angle can be due to multiple components of aging such as skin quality/elasticity, loss of platysma muscle tone, and submental fat accumulation. Traditionally, the procedure of choice for patients with an aging lower face and neck is a cervicofacial rhytidectomy. However, occasionally, a patient wishes to have no other facial surgery than an improvement of their excessive skin of the anterior, lateral, and/or posterior neck. In other instances, a patient may present with having had a face/neck-lifting procedure that left objectionable vertical/diagonal lines at the lateral neck. In both these instances, a surgeon should consider an isolated stork lift (ISL) procedure. An ISL procedure avoids and/or corrects problematic vertical/diagonal lateral neck folds by "walking" the excess skin flaps around the posterior inferior occipital hairline bilaterally, bringing the flaps together at the lateral and posterior neck, which sometimes involves a midline posterior dart excision of the dog ear. A patient presenting with excessive skin of the neck (anterior, lateral, and/or posterior) and/or residual vertical/diagonal skin folds is an excellent candidate for the ISL. The ISL procedure was performed on 273 patients over a 2-year period at The Morrow Institute. Patients were included if they had excessive skin of the anterior, lateral, and/or posterior neck and/or diagonal/vertical lateral bands and did not desire a full face-lifting procedure. Patients were excluded from this study if they would not accept having longer hair in order to cover the scar along the posterior inferior occipital hairline or a midline T-flap skin closure scar at the base of the posterior midline neck. Under a combination of local anesthesia and IV sedation, a postauricular face-lift incision was made that was extended in a circumoccipital fashion

An update to inplace testing of safety/relief valves utilizing lift assist technology

International Nuclear Information System (INIS)

Heorman, K.R.

1992-01-01

Inplace testing of safety and relief valves with lift-assist devices has received mixed reviews from nuclear power plant testing personnel. While many plants use the technology, most limit its use to testing main steam safety valves (even though both OM-1-1981 and PTC 25.3-1976 allow its use for several different service applications). Test coordinator concerns regarding the technology range from lift set point accuracy and repeatability to the quality of the test result output. In addition, OM-1-1981 and PTC 25.3-1976 differ in their approach to the technology. The reasons for the differences between PTC 25.3-1976 and OM-1-1981 are discussed along with additional considerations applicable to the use of the technology in testing liquid service valves. This paper shows that lift assist technology is capable of determining lift set points within the accuracy requirements of OM-1 and PTC 25.3. It also demonstrates that the technology should not be limited to compressible service systems. Also, improvements in test repeatability and output quality are discussed as a function of the assist device design used and valve characteristics. Lift assist testing is often preferred over inplace testing that uses direct system pressure. It is often more cost efficient than bench testing because it does not require removal of critical systems from service and transportation of components. Also, duplicating system temperatures and other environmental factors is not an issue during inplace testing. Valve testing that once required an outage and maintenance period can now be conducted prior to such periods. This approach minimizes the possibility of failures becoming critical path limiting items

[Origin of lifting and lowering theory and its herb pair study].

Science.gov (United States)

Guo, Zhao-Juan; Yuan, Yi-Ping; Kong, Li-Ting; Jia, Xiao-Yu; Wang, Ning-Ning; Dai, Ying; Zhai, Hua-Qiang

2017-08-01

Lifting and lowering theory is one of the important basis for guiding clinical medication. Through the study of ancient books and literature, we learned that lifting and lowering theory was originated in Huangdi Neijing, practiced more in the Shanghan Zabing Lun, established in Yixue Qiyuan, and developed in Compendium of Materia Medica and now. However, lifting and lowering theory is now mostly stagnated in the theoretical stage, with few experimental research. In the clinical study, the guiding role of lifting and lowering theory to prescriptions?mainly includes opposite?role?of lift and lower medicine property, mutual promotion of lift and lower medicine property, main role of lift medicine property and main role of lower medicine property. Under the guidance of lifting and lowering theory, the herb pair compatibility include herb combination of lift medicine property, herb combination of lift and lower medicine property and herb combination of lower medicine property. Modern biological technology was used in this study to carry out experimental research on the lifting and lowering theory, revealing the scientific connotation of it, which will help to promote clinical rational drug use. Copyright© by the Chinese Pharmaceutical Association.

Heavy Lift Vehicle (HLV) Avionics Flight Computing Architecture Study

Science.gov (United States)

Hodson, Robert F.; Chen, Yuan; Morgan, Dwayne R.; Butler, A. Marc; Sdhuh, Joseph M.; Petelle, Jennifer K.; Gwaltney, David A.; Coe, Lisa D.; Koelbl, Terry G.; Nguyen, Hai D.

2011-01-01

A NASA multi-Center study team was assembled from LaRC, MSFC, KSC, JSC and WFF to examine potential flight computing architectures for a Heavy Lift Vehicle (HLV) to better understand avionics drivers. The study examined Design Reference Missions (DRMs) and vehicle requirements that could impact the vehicles avionics. The study considered multiple self-checking and voting architectural variants and examined reliability, fault-tolerance, mass, power, and redundancy management impacts. Furthermore, a goal of the study was to develop the skills and tools needed to rapidly assess additional architectures should requirements or assumptions change.

Thermally stimulating mechanically-lifted well production

Energy Technology Data Exchange (ETDEWEB)

Richardson, E.A.; Hinson, R.A.

1984-06-19

A well which is producing slowly by artificial lift can be economically heated by first inflowing a nitrogen-generating solution, to form a pool of reacting liquid near the uppermost opening into the reservoir, then inflowing more solution while artificially-lifting liquid from near the lowermost opening into the reservoir at a rate substantially equalling the inflow rate.

Numerical Study of Transition of an Annular Lift Fan Aircraft

OpenAIRE

Yun Jiang; Bo Zhang

2016-01-01

The present study aimed at studying the transition of annular lift fan aircraft through computational fluid dynamics (CFD) simulations. The oscillations of lift and drag, the optimization for the figure of merit, and the characteristics of drag, yawing, rolling and pitching moments in transition are studied. The results show that a two-stage upper and lower fan lift system can generate oscillations of lift and drag in transition, while a single-stage inner and outer fan lift system can elimin...

Bilayer lift-off process for aluminum metallization

Science.gov (United States)

Wilson, Thomas E.; Korolev, Konstantin A.; Crow, Nathaniel A.

2015-01-01

Recently published reports in the literature for bilayer lift-off processes have described recipes for the patterning of metals that have recommended metal-ion-free developers, which do etch aluminum. We report the first measurement of the dissolution rate of a commercial lift-off resist (LOR) in a sodium-based buffered commercial developer that does not etch aluminum. We describe a reliable lift-off recipe that is safe for multiple process steps in patterning thin (recipe consists of an acid cleaning of the substrate, the bilayer (positive photoresist/LOR) deposition and development, the sputtering of the aluminum film along with a palladium capping layer and finally, the lift-off of the metal film by immersion in the LOR solvent. The insertion into the recipe of postexposure and sequential develop-bake-develop process steps are necessary for an acceptable undercut. Our recipe also eliminates any need for accompanying sonication during lift-off that could lead to delamination of the metal pattern from the substrate. Fine patterns were achieved for both 100-nm-thick granular aluminum/palladium bilayer bolometers and 500-nm-thick aluminum gratings with 6-μm lines and 4-μm spaces.

Study on dynamic lifting characteristics of control rod drive mechanism

International Nuclear Information System (INIS)

Shen Xiaoyao

2012-01-01

Based on the equations of the electric circuit and the magnetic circuit and analysis of the dynamic lifting process for the control rod drive mechanism (CRDM), coupled magnetic-electric-mechanical equations both for the static status and the dynamic status are derived. The analytical method is utilized to obtain the current and the time when the lift starts. The numerical simulation method of dynamic analysis recommended by ASME Code is utilized to simulate the dynamic lifting process of CRDM, and the dynamic features of the system with different design gaps are studied. Conclusions are drawn as: (1) the lifting-start time increases with the design gap, and the time for the lifting process is longer with larger gaps; (2) the lifting velocity increases with time; (3) the lifting acceleration increases with time, and with smaller gaps, the impact acceleration is larger. (author)

Proceedings of the CERI 2004 electricity conference : the future of electric power in North America. CD ed.

International Nuclear Information System (INIS)

2004-01-01

This conference offered an opportunity to review energy markets in North American with particular reference to opportunities for traditional technologies and new generation technologies based on renewable energy sources including wind powered generation. The presentations focused on relative fuel prices and the potential for distributed generation and demand side management. Several presentations examined the issue of why Canadian and North American markets remain divided about the best market design and how to ensure reliability. The 6 sessions were entitled: the future of generation in Canada; wind power opportunities and constraints; new business opportunities for distributed power and demand side management; the future of restructuring in North America; reliability; and, the future of restructuring in Alberta. tabs., figs

Analysis of lifting beam and redesigned lifting lugs for 241-AZ-01A decant pump

International Nuclear Information System (INIS)

Coverdell, B.L.

1994-01-01

This supporting document details calculations for the proper design of a lifting beam and redesigned lifting lugs for the 241AZO1A decant pump. This design is in accordance with Standard Architectural-Civil Design Criteria, Design Loads for Facilities (DOE-RL 1989) and is safety class three. The design and fabrication is in accordance with American Institute of Steel Construction, Manual of Steel Construction, (AISC, 1989) and the Hanford Hoisting and Rigging Manual (DOE-RL 1993)

International conference: nuclear power for the 21 st century; Conference internationale: L'energie nucleaire au 21. siecle

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-07-01

It is widely recognised that global energy demand will rise substantially during this century. The increased industrialization and urbanization of developing countries will produce large increases in energy demand in regions that currently have very low per capita energy use. This increasing demand for energy will need to be met in order to improve living standards for at least half of the world population and to reduce the economic imbalances between countries and regions. At the same time the use of fossil fuel based energy is identified as a major cause of environmental damage. The release of greenhouse gases from burning of fossil fuel in power stations and for transport is seen as a contributor to global warming. It is widely recognised that continued exploitation of fossil fuels and release of carbon dioxide will need to be controlled. After a prolonged period of slow development of nuclear power, confined to some countries in the world, it is now being recognised that nuclear energy has a potentially significant role to play in meeting the energy needs of the planet without damaging the environment. Developments in technology make the economics of nuclear power more attractive, and they may become even more so as fossil fuel prices continue to rise.or a widespread use of nuclear power, however, there remain concerns on the safety, security, waste and proliferation aspects. The global application of safety standards and appropriate security measures are required to ensure acceptable levels of protection. Effective control measures are required to ensure that non-proliferation commitments are honored. Handling nuclear waste safely and securely is achievable, but continues to remain as a public concern. The broad strategic objectives of the Conference are the following: to review the role of nuclear power and to define the potential benefits (energy security, sustainability and improved environmental protection) that expanding nuclear power offers to meet the

Nordic noir and lifted localities

DEFF Research Database (Denmark)

Hansen, Kim Toft

What I do here is to draw attention to a particular visual quality of recent Nordic noir and to relate the visuality of TV-drama to what I – with a term borrowed from Roland Robertson – dub lifted localites.......What I do here is to draw attention to a particular visual quality of recent Nordic noir and to relate the visuality of TV-drama to what I – with a term borrowed from Roland Robertson – dub lifted localites....

Proceedings of the WIN-Global 2008 conference

International Nuclear Information System (INIS)

2008-01-01

WiN-France hosted the 16. WIN-Global conference May 26-30, 2008, in Marseille, France. The conference was attended by over 150 delegates, representing 30 countries. Canadian participants, from many diverse backgrounds, attended the annual conference from AECL, Bruce Power, CNSC, NB Power and OPG. The theme: Maintaining Key Competencies, Arising Key Competencies for Nuclear Energy: A Challenge and Opportunity for Diversity Development, emphasized the challenges ahead in providing a skilled workforce for the nuclear renaissance, as new build projects and a vast number of retirements are expected around the world within the next 5 years. The conference addressed such questions as 'How will nuclear, attract, develop and retain staff?' A technical tour of Marcoule invited conference attendees to visit one of: Atalante, a high level nuclear chemistry laboratory; Phenix, a fast breeding research reactor; or AVM, a vitrification plant. A subsequent technical tour visited Cadarache providing the opportunity to view ITER, the international fusion research project

Proceedings of the WIN-Global 2008 conference

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-07-01

WiN-France hosted the 16. WIN-Global conference May 26-30, 2008, in Marseille, France. The conference was attended by over 150 delegates, representing 30 countries. Canadian participants, from many diverse backgrounds, attended the annual conference from AECL, Bruce Power, CNSC, NB Power and OPG. The theme: Maintaining Key Competencies, Arising Key Competencies for Nuclear Energy: A Challenge and Opportunity for Diversity Development, emphasized the challenges ahead in providing a skilled workforce for the nuclear renaissance, as new build projects and a vast number of retirements are expected around the world within the next 5 years. The conference addressed such questions as 'How will nuclear, attract, develop and retain staff?' A technical tour of Marcoule invited conference attendees to visit one of: Atalante, a high level nuclear chemistry laboratory; Phenix, a fast breeding research reactor; or AVM, a vitrification plant. A subsequent technical tour visited Cadarache providing the opportunity to view ITER, the international fusion research project.

Proceedings of the WIN-Global 2008 conference

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-07-01

WiN-France hosted the 16. WIN-Global conference May 26-30, 2008, in Marseille, France. The conference was attended by over 150 delegates, representing 30 countries. Canadian participants, from many diverse backgrounds, attended the annual conference from AECL, Bruce Power, CNSC, NB Power and OPG. The theme: Maintaining Key Competencies, Arising Key Competencies for Nuclear Energy: A Challenge and Opportunity for Diversity Development, emphasized the challenges ahead in providing a skilled workforce for the nuclear renaissance, as new build projects and a vast number of retirements are expected around the world within the next 5 years. The conference addressed such questions as 'How will nuclear, attract, develop and retain staff?' A technical tour of Marcoule invited conference attendees to visit one of: Atalante, a high level nuclear chemistry laboratory; Phenix, a fast breeding research reactor; or AVM, a vitrification plant. A subsequent technical tour visited Cadarache providing the opportunity to view ITER, the international fusion research project.

Reduction of Dynamic Loads in Mine Lifting Installations

Science.gov (United States)

Kuznetsov, N. K.; Eliseev, S. V.; Perelygina, A. Yu

2018-01-01

Article is devoted to a problem of decrease in the dynamic loadings arising in transitional operating modes of the mine lifting installations leading to heavy oscillating motions of lifting vessels and decrease in efficiency and reliability of work. The known methods and means of decrease in dynamic loadings and oscillating motions of the similar equipment are analysed. It is shown that an approach based on the concept of the inverse problems of dynamics can be effective method of the solution of this problem. The article describes the design model of a one-ended lifting installation in the form of a two-mass oscillation system, in which the inertial elements are the mass of the lifting vessel and the reduced mass of the engine, reducer, drum and pulley. The simplified mathematical model of this system and results of an efficiency research of an active way of reduction of dynamic loadings of lifting installation on the basis of the concept of the inverse problems of dynamics are given.

Searching for ski-lift injury: an uphill struggle?

Science.gov (United States)

Smartt, Pam; Chalmers, David

2010-03-01

Injuries arising from ski-lift malfunction are rare. Most arise from skier error when embarking or disembarking, or from improper lift operation. A search of the literature failed to uncover any studies focusing specifically on ski-lift injuries. The purpose of this study was to identify and characterise ski-lift injury resulting in hospitalisation and comment on barriers to reporting and reporting omissions. New Zealand hospitalised injury discharges 2000-2005 formed the primary dataset. To aid case identification these data were linked to ACC compensated claims for the same period and the data searched for all hospitalised cases of injury arising from ski-lifts. 44 cases were identified representing 2% of snow-skiing/snowboarding cases. 28 cases (64%) were male and 16 (36%) female, the average age was 32 yrs (range 5-73 yrs). The majority of cases were snow-skiers (35 cases, 80%). Most of the injuries were serious, or potentially so, with 1 case of traumatic pneumothorax, one of pulmonary embolism (after jumping from a ski-lift) and 28 cases sustaining fractures (six to the neck-of-femur, one to the lumbar spine and one to the pubis). ICISS scores for all cases ranged from 1.00 to 0.8182 (probability of dying in hospital 0-18.18%). Only 14 (32%) cases could be easily identified from ICD-10-AM e-codes and activity codes in the discharge summary. The ICD-10-AM external cause code for ski-lift injury V98 ("other specified transport accidents") was only assigned to 39% of cases. The type of ski-lift could only be determined in 24 cases (55%). Copyright 2009 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

High-Temperature-High-Volume Lifting for Enhanced Geothermal Systems

Energy Technology Data Exchange (ETDEWEB)

Turnquist, Norman [GE Global Research, Munchen (Germany); Qi, Xuele [GE Global Research, Munchen (Germany); Raminosoa, Tsarafidy [GE Global Research, Munchen (Germany); Salas, Ken [GE Global Research, Munchen (Germany); Samudrala, Omprakash [GE Global Research, Munchen (Germany); Shah, Manoj [GE Global Research, Munchen (Germany); Van Dam, Jeremy [GE Global Research, Munchen (Germany); Yin, Weijun [GE Global Research, Munchen (Germany); Zia, Jalal [GE Global Research, Munchen (Germany)

2013-12-20

This report summarizes the progress made during the April 01, 2010 – December 30, 2013 period under Cooperative Agreement DE-EE0002752 for the U.S. Department of Energy entitled “High-Temperature-High-Volume Lifting for Enhanced Geothermal Systems.” The overall objective of this program is to advance the technology for well fluids lifting systems to meet the foreseeable pressure, temperature, and longevity needs of the Enhanced Geothermal Systems (EGS) industry for the coming ten years. In this program, lifting system requirements for EGS wells were established via consultation with industry experts and site visits. A number of artificial lift technologies were evaluated with regard to their applicability to EGS applications; it was determined that a system based on electric submersible pump (ESP) technology was best suited to EGS. Technical barriers were identified and a component-level technology development program was undertaken to address each barrier, with the most challenging being the development of a power-dense, small diameter motor that can operate reliably in a 300°C environment for up to three years. Some of the targeted individual component technologies include permanent magnet motor construction, high-temperature insulation, dielectrics, bearings, seals, thrust washers, and pump impellers/diffusers. Advances were also made in thermal management of electric motors. In addition to the overall system design for a full-scale EGS application, a subscale prototype was designed and fabricated. Like the full-scale design, the subscale prototype features a novel “flow-through-the-bore” permanent magnet electric motor that combines the use of high temperature materials with an internal cooling scheme that limits peak internal temperatures to <330°C. While the full-scale high-volume multi-stage pump is designed to lift up to 80 kg/s of process water, the subscale prototype is based on a production design that can pump 20 kg/s and has been modified

Does team lifting increase the variability in peak lumbar compression in ironworkers?

Science.gov (United States)

Faber, Gert; Visser, Steven; van der Molen, Henk F; Kuijer, P Paul F M; Hoozemans, Marco J M; Van Dieën, Jaap H; Frings-Dresen, Monique H W

2012-01-01

Ironworkers frequently perform heavy lifting tasks in teams of two or four workers. Team lifting could potentially lead to a higher variation in peak lumbar compression forces than lifts performed by one worker, resulting in higher maximal peak lumbar compression forces. This study compared single-worker lifts (25-kg, iron bar) to two-worker lifts (50-kg, two iron bars) and to four-worker lifts (100-kg, iron lattice). Inverse dynamics was used to calculate peak lumbar compression forces. To assess the variability in peak lumbar loading, all three lifting tasks were performed six times. Results showed that the variability in peak lumbar loading was somewhat higher in the team lifts compared to the single-worker lifts. However, despite this increased variability, team lifts did not result in larger maximum peak lumbar compression forces. Therefore, it was concluded that, from a biomechanical point of view, team lifting does not result in an additional risk for low back complaints in ironworkers.

Lift-(gasless) laparoscopic surgery under regional anesthesia.

Science.gov (United States)

Kruschinski, Daniel; Homburg, Shirli

2005-01-01

The objective of this Chapter was to investigate the feasibility and outcome of gasless laparoscopy under regional anesthesia. A prospective evaluation of Lift-(gasless) laparoscopic procedures under regional anesthesia (Canadian Task Force classification II-1) was done at three endoscopic gynecology centers (franchise system of EndGyn(r)). Sixty-three patients with gynecological diseases comprised the cohort. All patients underwent Lift-laparoscopic surgery under regional anesthesia: 10 patients for diagnostic purposes, 17 for surgery of ovarian tumors, 14 to remove fibroids, and 22 for hysterectomies. All patients were operated without conversion to general anesthesia and without perioperative or anesthesiologic complications. Lift-laparoscopy under regional anesthesia can be recommended to all patients who desire laparoscopic intervention without general anesthesia. For elderly patients, those with cardiopulmonary risks, during pregnancy, or with contraindications for general anesthesia, Lift-laparoscopy under regional anesthesia should be the procedure of choice.

Analysis of ergonomic and unergonomic human lifting behaviors by using Inertial Measurement Units

Directory of Open Access Journals (Sweden)

Kuschan Jan

2017-03-01

Full Text Available This paper presents an analysis of two distinct human lifting movements regarding acceleration and angular velocity. For the first movement, the ergonomic one, the test persons produced the lifting power by squatting down, bending at the hips and knees only. Whereas performing the unergonomic one they bent forward lifting the box mainly with their backs. The measurements were taken by using a vest equipped with five Inertial Measurement Units (IMU with 9 Dimensions of Freedom (DOF each. In the following the IMU data captured for these two movements will be evaluated using statistics and visualized. It will also be discussed with respect to their suitability as features for further machine learning classifications. The reason for observing these movements is that occupational diseases of the musculoskeletal system lead to a reduction of the workers’ quality of life and extra costs for companies. Therefore, a vest, called CareJack, was designed to give the worker a real-time feedback about his ergonomic state while working. The CareJack is an approach to reduce the risk of spinal and back diseases. This paper will also present the idea behind it as well as its main components.

The effect of electrohydrodynamic force on the lift coefficient of a NACA 0015 airfoil

Science.gov (United States)

Yusof, Y.; Hossain, A.; Abdullah, A. H.; Nasir, Rizal M. E.; Hamid, A.; Muthmainnah, N.; N, M.

2017-11-01

Lift, the force component that is perpendicular to the line of flight, is generated when a small aircraft moves through the air. With the help of the sets of flaps and slats on its wing, the pilot controls his aircraft manoeuvring in the air. In this study, we preferred to cut the drawbacks of the flaps system by introducing the electrohydrodynamic actuator. Widely known as plasma actuator, it is able to improve the induced lift force as well as the efficiency of a small aircraft system. A dielectric-barrier-discharge actuator using a 6 kV AC power supply was developed and tested on a NACA 0015 airfoil using copper as the electrodes and kapton as its dielectric component. The experimental results showed that it was successful in presenting a positive effect of the plasma actuator on the lift coefficient of the airfoil at smaller angle of attack, where enhancements ranged between 0.7% and 1.8%. However, at a higher angle, the results were not as swayed as it was desired since the energy exerted by the plasma actuator on the lift performance of the airfoil was inadequate. Further tests are needed using higher rated voltage supply and other equipment to improve the capability of the actuator in refining the aerodynamic performance of the airfoil.

Endoscopic brow lifts uber alles.

Science.gov (United States)

Patel, Bhupendra C K

2006-12-01

Innumerable approaches to the ptotic brow and forehead have been described in the past. Over the last twenty-five years, we have used all these techniques in cosmetic and reconstructive patients. We have used the endoscopic brow lift technique since 1995. While no one technique is applicable to all patients, the endoscopic brow lift, with appropriate modifications for individual patients, can be used effectively for most patients with brow ptosis. We present the nuances of this technique and show several different fixation methods we have found useful.

The Effect of Midline Corset Platysmaplasty on Degree of Face-lift Flap Elevation During Concomitant Deep-Plane Face-lift: A Cadaveric Study.

Science.gov (United States)

Jacono, Andrew A; Malone, Melanie H

2016-05-01

The evaluation of the effects of midline platysmaplasty concomitant with rhytidectomy. To determine whether midline platysmaplasty limits the degree of lift during deep-plane face-lift. Deep-plane rhytidectomy was performed on 10 cadaveric hemifaces. The redundant skin for excision after performing the face-lift was measured with and without midline platymaplasty. Deep-plane rhytidectomy. The redundant skin was measured preauricularly in the vertical and horizontal dimension, and postauricularly after deep-plane face-lift and after adding a midline platysmaplasty. Concomitant midline platysmaplasty significantly reduced the amount of lift during concomitant deep-plane rhytidectomy preauricularly in the vertical dimension by 40.5% (from 37.0 mm excess skin redraped to 22.0 mm) and postauricularly by 23.9% (from 40.6 mm excess skin redraped to 30.9 mm) (P jawline and midface during rhytidectomy. NA.

Proceedings: Cooling tower and advanced cooling systems conference

International Nuclear Information System (INIS)

1995-02-01

This Cooling Tower and Advanced Cooling Systems Conference was held August 30 through September 1, 1994, in St. Petersburg, Florida. The conference was sponsored by the Electric Power Research Institute (EPRI) and hosted by Florida Power Corporation to bring together utility representatives, manufacturers, researchers, and consultants. Nineteen technical papers were presented in four sessions. These sessions were devoted to the following topics: cooling tower upgrades and retrofits, cooling tower performance, cooling tower fouling, and dry and hybrid systems. On the final day, panel discussions addressed current issues in cooling tower operation and maintenance as well as research and technology needs for power plant cooling. More than 100 people attended the conference. This report contains the technical papers presented at the conference. Of the 19 papers, five concern cooling tower upgrades and retrofits, five to cooling tower performance, four discuss cooling tower fouling, and five describe dry and hybrid cooling systems. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database

Conference summaries

International Nuclear Information System (INIS)

1983-01-01

The papers presented at this conference cover the fields of thermalhydraulics, nuclear plant design and operation, licensing, decontamination, restoration and dismantling of nuclear power facilities, services to the nuclear industry, new applications of nuclear technology, reactor physics and fuel cycles, accelerator-breeders, fusion research and lasers

Darrieus wind-turbine and pump performance for low-lift irrigation pumping

Science.gov (United States)

Hagen, L. J.; Sharif, M.

1981-10-01

In the Great Plains about 15 percent of the irrigation water pumped on farms comes from surface water sources; for the United States as a whole, the figure is about 22 percent. Because of forecast fuel shortages, there is a need to develop alternative energy sources such as wind power for surface water pumping. Specific objectives of this investigation were to: design and assemble a prototype wind powered pumping system for low lift irrigation pumping; determine performance of the prototype system; design and test an irrigation system using the wind powered prototype in a design and test an farm application; and determine the size combinations of wind turbines, tailwater pits, and temporary storage reservoirs needed for successful farm application of wind powered tailwater pumping systems in western Kansas. The power source selected was a two bladed, 6 m diameter, 9 m tall Darrieus vertical axis wind turbine with 0.10 solidity and 36.1 M(2) swept area.

Proceedings of CanWEA's 23. annual conference

International Nuclear Information System (INIS)

2007-01-01

This conference was attended by wind turbine manufacturers, component suppliers, wind energy project developers, utilities and a broad range of service providers to the wind power industry. It provided a forum to identify key issues facing the wind power industry and the measures that must be taken if Canada is to meet the targets and objectives established for wind energy by federal and provincial governments. It is anticipated that the rapid growth in the wind power industry will help create jobs and training opportunities as well as provide economic benefits to local communities. The conference was divided into 3 streams, namely policy; business and development; and technical. Alberta policy and Quebec policy issues were discussed on the first day of the conference along with project financing issues and operations/maintenance of wind farms. Wind in cold climates was also discussed along with wind and grid reliability issues. Policy developments in western Canada, Atlantic Canada and Ontario were discussed on the second day of the conference along with wind farm siting issues, small wind projects under 10 MW, wind resource assessment, performance measurement, and advances in wind forecasting. Municipal involvement in wind projects was discussed on the final day of the conference along with wind integration with conventional grids and the need for trained service technicians in the Canadian wind industry. Forty presentations from the conference have been catalogued separately for inclusion in this database

Simplified theory of an active lift turbine with controlled displacement

OpenAIRE

Lecanu , Pierre ,; Breard , Joel; Mouazé , Dominique

2016-01-01

It is presented in this article, a simplified theory of the active lift turbine which has been the subject of several patent[4, 5, 11]. A simplified theory is proposed to extend the Betz limit of the yield on vertical axis wind turbine. This work can be extended either on wind driven or marine current turbine. Based on kinetic energy calculation , that theory demonstrates that the radial force acting on the blade can be used to extend the maximum recoverable power, mainly by transforming a li...

Reinforced orbitotemporal lift: contribution to midface rejuvenation.

Science.gov (United States)

Renó, Waldir Teixeira

2003-02-01

The changes in the aging face occur from progressive ptosis of the skin, fat, and muscle, in conjunction with bone absorption and cartilage atrophy. In the orbital region, hollowness and compartmentalization occur. Conventional face lift procedures correct only the skin flaccidity, and superficial musculoaponeurotic system techniques reposition the skin and platysma without repositioning the middle third of the face, creating an artificial jawline. Subperiosteal rhytidectomy disrupts the anatomy of the periorbita, which gives the patient a certain scarecrow aspect. Composite rhytidectomy associated with brow lift and blepharoplasty may offer better results, with improvement in the malar and orbital regions. The reinforced orbitotemporal lift (ROTEL) is a new procedure in a face lift that allows the orbicularis oculi muscle and all the structures connected to it to be elevated and stretched and the orbitotemporal skin to be raised, repositioning these structures and ending orbital compartmentalization. The result is an impressive improvement in the malar-orbitotemporal region, resulting in a natural and youthful appearance.

Spherical projections and liftings in geometric tomography

DEFF Research Database (Denmark)

Goodey, Paul; Kiderlen, Markus; Weil, Wolfgang

2011-01-01

We consider a variety of integral transforms arising in Geometric Tomography. It will be shown that these can be put into a common framework using spherical projection and lifting operators. These operators will be applied to support functions and surface area measures of convex bodies and to rad......We consider a variety of integral transforms arising in Geometric Tomography. It will be shown that these can be put into a common framework using spherical projection and lifting operators. These operators will be applied to support functions and surface area measures of convex bodies...... and to radial functions of star bodies. We then investigate averages of lifted projections and show that they correspond to self-adjoint intertwining operators. We obtain formulas for the eigenvalues of these operators and use them to ascertain circumstances under which tomographic measurements determine...... the original bodies. This approach via mean lifted projections leads us to some unexpected relationships between seemingly disparate geometric constructions....

DeepTalk: A complete conference in a picture

International Nuclear Information System (INIS)

Watts, Gordon

2010-01-01

Particle physics conferences lasting a week (like CHEP) can have 100's of talks and posters presented. Current conference web interfaces (like Indico) are well suited to finding a talk by author or by time-slot. However, browsing the complete material in a modern large conference is not user friendly. Browsing involves continually making the expensive transition between HTML viewing and talk-slides (which are either PDF files or some other format). Further the web interfaces aren't designed for undirected browsing. The advent of multi-core computing and advanced video cards means that we have more processor power available for visualization than any time in the past. This poster describes a technique of rendering a complete conference's slides and posters as a single very large picture. Standard plug-in software for a browser allows a user to zoom in on a portion of the conference that looks interesting. As the user zooms further more and more details become visible, allowing the user to make a quick and chep decision on whether to spend more time on a particular talk. The project, DeepConference, has been implemented as a public web site and can render any conference whose agenda is powered by Indico. The rendering technology is powered by the free download, Silverlight. The poster discusses the implementation and use as well as cross platform performance and possible future directions. A demo will be shown.

Motor of Lift RSG-GAS Performance Analysis after Repair

International Nuclear Information System (INIS)

Asep-Saepuloh; Yayan-Andriyanto; Yuyut-Suraniyanto

2006-01-01

The out of order an equipment is ordinary natural process happened, above all the equipment be used continually with very old time, as for as out of order can be resulted from kinds of cause. Lift motor out of order can be result by motor is broken or happened the body shorten then affected do not function it the lift, so until done rewinding process. The rewinding is furl to repeat at motor coils. Motor of Lift represent main activator machine turning around shares pulley. Lift Motor will work if there is called in normal operation condition or the moment manual switch if done maintenance. Motor used at lift is motor three phases with two speeds that is low speed and high speed. Rewinding process must be done removed the motor from Lift machine and have to be done by professional workshop. In during function test take place, temperature at coil reach 70 o C (exceeding boundary permitted). After done installation addition thermal at motor coil hence his temperature become normal that is only reach 50 o C. (author)

TCA High Lift Preliminary Assessment

Science.gov (United States)

Wyatt, G. H.; Polito, R. C.; Yeh, D. T.; Elzey, M. E.; Tran, J. T.; Meredith, Paul T.

1999-01-01

This paper presents a TCA (Technology Concept Airplane) High lift Preliminary Assessment. The topics discussed are: 1) Model Description; 2) Data Repeatability; 3) Effect of Inboard L.E. (Leading Edge) Flap Span; 4) Comparison of 14'x22' TCA-1 With NTF (National Transonic Facility) Modified Ref. H; 5) Comparison of 14'x22' and NTF Ref. H Results; 6) Effect of Outboard Sealed Slat on TCA; 7) TCA Full Scale Build-ups; 8) Full Scale L/D Comparisons; 9) TCA Full Scale; and 10) Touchdown Lift Curves. This paper is in viewgraph form.

Evaluation of ceiling lifts: transfer time, patient comfort and staff perceptions.

Science.gov (United States)

Alamgir, Hasanat; Li, Olivia Wei; Yu, Shicheng; Gorman, Erin; Fast, Catherine; Kidd, Catherine

2009-09-01

Mechanical lifting devices have been developed to reduce healthcare worker injuries related to patient handling. The purpose of this study was to evaluate ceiling lifts in comparison to floor lifts based on transfer time, patient comfort and staff perceptions in three long-term care facilities with varying ceiling lift coverage. The time required to transfer or reposition patients along with patient comfort levels were recorded for 119 transfers. Transfers performed with ceiling lifts required on average less time (bed to chair transfers: 156.9 seconds for ceiling lift, 273.6 seconds for floor lift) and were found to be more comfortable for patients. In the three facilities, 143 healthcare workers were surveyed on their perceptions of patient handling tasks and equipment. For both transferring and repositioning tasks, staff preferred to use ceiling lifts and also found them to be less physically demanding. Further investigation is needed on repositioning tasks to ensure safe practice.

Effects of squat lift training and free weight muscle training on maximum lifting load and isolinetic peak torque of young adults without impairments.

Science.gov (United States)

Yeung, S S; Ng, G Y

2000-06-01

Manual lifting is a frequent cause of back injury, and there is no evidence as to which training mode can provide the best training effect for lifting performance and muscle force. The purpose of this study was to examine the effects of a squat lift training and a free weight muscle training program on the maximum lifting load and isokinetic peak torque in subjects without known neuromuscular or musculoskeletal impairments. Thirty-six adults (20 male, 16 female) without known neuromuscular or musculoskeletal impairments participated. The subjects' mean age was 21.25 years (SD=1.16, range=20-24). Subjects were divided into 3 groups. Subjects in group 1 (n=12) performed squat lift training. Subjects in group 2 (n=12) participated in free weight resistance training of their shoulder abductors, elbow flexors, knee extensors and trunk extensors. Subjects in group 3 (n=12) served as controls. The maximum lifting load and isokinetic peak torques of the trunk extensors, knee extensors, elbow flexors, and shoulder abductors of each subject were measured before and after the study. Training was conducted on alternate days for 4 weeks, with an initial load of 80% of each subject's maximum capacity and with the load increased by 5% weekly. All groups were comparable for all measured variables before the study. After 4 weeks, subjects in groups 1 and 2 demonstrated more improvement in maximum lifting load and isokinetic peak torque of the back extensors compared with the subjects in group 3, but the 2 training groups were not different. The findings demonstrate that both squat lift and free weight resistance training are equally effective in improving the lifting load and isokinetic back extension performance of individuals without impairments.

Prediction of peak back compressive forces as a function of lifting speed and compressive forces at lift origin and destination - a pilot study.

Science.gov (United States)

Greenland, Kasey O; Merryweather, Andrew S; Bloswick, Donald S

2011-09-01

To determine the feasibility of predicting static and dynamic peak back-compressive forces based on (1) static back compressive force values at the lift origin and destination and (2) lifting speed. Ten male subjects performed symmetric mid-sagittal floor-to-shoulder, floor-to-waist, and waist-to-shoulder lifts at three different speeds (slow, medium, and fast), and with two different loads (light and heavy). Two-dimensional kinematics and kinetics were captured. Linear regression analyses were used to develop prediction equations, the amount of predictability, and significance for static and dynamic peak back-compressive forces based on a static origin and destination average (SODA) back-compressive force. Static and dynamic peak back-compressive forces were highly predicted by the SODA, with R(2) values ranging from 0.830 to 0.947. Slopes were significantly different between slow and fast lifting speeds (p assessments at the origin and destination of a lifting task. This could be valuable for enhancing job design and analysis in the workplace and for large-scale studies where a full analysis of each lifting task is not feasible.

EMG Processing Based Measures of Fatigue Assessment during Manual Lifting

Directory of Open Access Journals (Sweden)

E. F. Shair

2017-01-01

Full Text Available Manual lifting is one of the common practices used in the industries to transport or move objects to a desired place. Nowadays, even though mechanized equipment is widely available, manual lifting is still considered as an essential way to perform material handling task. Improper lifting strategies may contribute to musculoskeletal disorders (MSDs, where overexertion contributes as the highest factor. To overcome this problem, electromyography (EMG signal is used to monitor the workers’ muscle condition and to find maximum lifting load, lifting height and number of repetitions that the workers are able to handle before experiencing fatigue to avoid overexertion. Past researchers have introduced several EMG processing techniques and different EMG features that represent fatigue indices in time, frequency, and time-frequency domain. The impact of EMG processing based measures in fatigue assessment during manual lifting are reviewed in this paper. It is believed that this paper will greatly benefit researchers who need a bird’s eye view of the biosignal processing which are currently available, thus determining the best possible techniques for lifting applications.

EMG Processing Based Measures of Fatigue Assessment during Manual Lifting

Science.gov (United States)

Marhaban, M. H.; Abdullah, A. R.

2017-01-01

Manual lifting is one of the common practices used in the industries to transport or move objects to a desired place. Nowadays, even though mechanized equipment is widely available, manual lifting is still considered as an essential way to perform material handling task. Improper lifting strategies may contribute to musculoskeletal disorders (MSDs), where overexertion contributes as the highest factor. To overcome this problem, electromyography (EMG) signal is used to monitor the workers' muscle condition and to find maximum lifting load, lifting height and number of repetitions that the workers are able to handle before experiencing fatigue to avoid overexertion. Past researchers have introduced several EMG processing techniques and different EMG features that represent fatigue indices in time, frequency, and time-frequency domain. The impact of EMG processing based measures in fatigue assessment during manual lifting are reviewed in this paper. It is believed that this paper will greatly benefit researchers who need a bird's eye view of the biosignal processing which are currently available, thus determining the best possible techniques for lifting applications. PMID:28303251

Cost Benefit Analysis of Boat Lifts

Science.gov (United States)

2014-09-01

associated with commercial boat lifts were obtained through a market survey based on products advertised for sale to the general public. The information...from the market survey and knowledge of specific boat maintenance items susceptible to cost reduction using a boat lift were then compared to identify...transferred to the Boat Inventory Manager ( BIM ). Custodians are responsible for maintaining boats and small craft in good working order at all times

International Conference on Recent Developments and Applications of Nuclear Technologies - Conference Abstracts

International Nuclear Information System (INIS)

Zakrzewska-Trznadel, G.

2008-01-01

The aim of the Conference was to offer an opportunity to interchange views and experiences, as well as to present the state of the art and modern trends concerning research and applications in the field of nuclear technologies. It was hoped that the Conference may fill up the gap on the field of information about possibilities and results of the application of nuclear technologies in modern economy of the 21 century, particularly in: industry, food processing, heritage preservation, environmental protection, homeland security and health protection. One session, with invited lectures, was entirely devoted to modern nuclear technologies for power generation. Conference participants presented 7 plenary lectures, 68 oral communications in 8 sessions and 98 posters

SAGD gas lift completions and optimization : a field case study at Surmont

Energy Technology Data Exchange (ETDEWEB)

Handfield, T.C.; Nations, T.; Noonan, S.G. [ConocoPhillips Co., Houston, TX (United States)

2008-10-15

Gas lift completions for steam assisted gravity drainage (SAGD) producers are unique. Because of the extreme temperatures of the downhole environment, conventional gas lift valves and mandrels with a packer completion cannot be used. Most gas lifts enter the production stream downhole through open-ended tubing or nozzles, which if not properly sized could result in operational issues, such as fluid/gas slugging and pressure instabilities which negatively effect the overall lift efficiency. ConocoPhillips performed a study in 2006 to design a gas lift system for the Surmont SAGD development that would allow better control of lift gas into the production string. The wells completed with gas lift were placed on production in 2007. This paper discussed the data collection effort and analysis completed to determine the efficiency of the two types of gas lift nozzles used in the completions. It also presented the methodology for optimization of SAGD gas lift systems and recommendations for future improvement. Background information on the Surmont oil sands project, located southeast of Fort McMurray in the Athabasca oil sands was included along with a historical perspective of the SAGD Surmont gas lift experience followed by a discussion of the Surmont initial gas lift design. Last, the paper discussed the Surmont gas lift start-up and optimization. It was concluded that installation of backcheck valves in coil tubing used for gas lift may mitigate plugging issues on initial start-up and following periods of shut-down. 5 refs., 10 figs.

International conference on innovative technologies for nuclear fuel cycles and nuclear power. Unedited proceedings

International Nuclear Information System (INIS)

2004-01-01

Nuclear power is a significant contributor to the global supply of electricity, and continues to be the major source that can provide electricity on a large scale with a comparatively minimal impact on the environment. But it is evident that, despite decades of experience with this technology, nuclear power today remains mainly in a holding position, with its future somewhat uncertain primarily due to concerns related to waste, safety and security. One of the most important factors that would influence future nuclear growth is the innovation in reactor and fuel cycle technologies to successfully maximize the benefits of nuclear power while minimizing the associated concerns. The main objectives of the Conference were to facilitate exchange of information between senior experts and policy makers from Member States and international organizations on important aspects of the development of innovative technologies for future generations of nuclear power reactors and fuel cycles; to create an understanding of the social, environmental and economic conditions that would facilitate innovative and sustainable nuclear technologies; and to identify opportunities for collaborative work between Member States and international organizations and programmes. All relevant aspects of innovative technologies for nuclear fuel cycles and nuclear power were discussed in an open, frank and objective manner. These proceedings contain a summary of the results of the conference, invited and contributed papers, and summaries of panel discussions. No large increase in the use of nuclear energy is foreseen in the near and medium term, but is likely in the long term if developing country per-capita electricity consumption reaches that of the developed world. The nuclear sector including regulators view an increased use of nuclear energy as the solution for global sustainable energy needs considering that significant reductions in CO 2 emissions would be required. Although the current nuclear

Toward a new nanoLIFT transfer process

International Nuclear Information System (INIS)

Mezel, C.; Hallo, L.; Breil, J.; Souquet, A.; Guillemot, F.; Bourgeade, A.; Hebert, D.; Saut, O.

2010-01-01

The Laser Induced Forward Transfer (LIFT) is a direct-write technique used to print biological materials such as living cells or molecules. During the LIFT process, the biomaterial to be printed is deposited on a target submitted to a nanosecond laser shot, and the ejecta are collected onto a receiving substrate. Despite the several advantages of this technique (control of the propelled quantity, no spoiling of the substrate), it remains difficult to be employed due to the high sensitivity of its control parameters. Recently, Duocastella published some experimental results which exhibit the real-time jet formation process, under conditions similar to those present in the LIFT process. In the first Section, a typical experimental setup for LIFT process is presented. Then, simulations of Duocastella's and Guillemot's experiments are carried out to model the jet formation in water when irradiated by an ultraviolet nanosecond laser pulse. The 2D axisymmetric hydrodynamic code CHIC (Code d'Hydrodynamique et d'Implosion du CELIA) is used for these simulations with included equations of state (EOS) to take into account the behavior of water under standard conditions. Finally, an improvement of the LIFT technique which consists in using femtosecond lasers instead of nanosecond ones, is presented. It would allow to process smaller bioelements and to control the jet diameter, as it is directly related to the laser beam waist.

Analytical investigation of low temperature lift energy conversion systems with renewable energy source

International Nuclear Information System (INIS)

Lee, Hoseong; Hwang, Yunho; Radermacher, Reinhard

2014-01-01

The efficiency of the renewable energy powered energy conversion system is typically low due to its moderate heat source temperature. Therefore, improving its energy efficiency is essential. In this study, the performance of the energy conversion system with renewable energy source was theoretically investigated in order to explore its design aspect. For this purpose, a computer model of n-stage low temperature lift energy conversion (LTLEC) system was developed. The results showed that under given operating conditions such as temperatures and mass flow rates of heat source and heat sink fluids the unit power generation of the system increased with the number of stage, and it became saturated when the number of staging reached four. Investigation of several possible working fluids for the optimum stage LTLEC system revealed that ethanol could be an alternative to ammonia. The heat exchanger effectiveness is a critical factor on the system performance. The power generation was increased by 7.83% for the evaporator and 9.94% for the condenser with 10% increase of heat exchanger effectiveness. When these low temperature source fluids are applied to the LTLEC system, the heat exchanger performance would be very critical and it has to be designed accordingly. - Highlights: •Energy conversion system with renewable energy is analytically investigated. •A model of multi-stage low temperature lift energy conversion systems was developed. •The system performance increases as the stage number is increased. •The unit power generation is increased with increase of HX effectiveness. •Ethanol is found to be a good alternative to ammonia

International conference on management of spent fuel from nuclear power reactors. Book of extended synopses

International Nuclear Information System (INIS)

2006-01-01

This document contains 48 extended synopses of the International Conference on Management of Spent Fuel from Nuclear Power Reactors. The major topics covered related to national programmes in spent fuel management as well as regional trends, technology and safety/security aspects of wet and dry storage, licensing and regulation, quality assurance, design control, operating experience, R and D, and special aspects of spent fuel storage including in-service inspection, robotics, heat removal, and other engineering considerations. Each of the extended synopses was indexed separately

Airfoil design: Finding the balance between design lift and structural stiffness

DEFF Research Database (Denmark)

Bak, Christian; Gaudern, Nicholas; Zahle, Frederik

2014-01-01

When upscaling wind turbine blades there is an increasing need for high levels of structural efficiency. In this paper the relationships between the aerodynamic characteristics; design lift and lift-drag ratio; and the structural characteristics were investigated. Using a unified optimization setup......, the design lift coefficient increases if the box length reduces and at the same time the relative thickness increases. Even though the conclusions are specific to the airfoil design approach used, the study indicated that an increased design lift required slightly higher relative thickness compared...... to airfoils with lower design lift to maintain the flapwise stiffness. Also, the study indicated that the lift-drag ratio as a function of flapwise stiffness was relatively independent of the airfoil design with a tendency that the lift-drag ratio decreased for large box lengths. The above conclusions were...

Airfoil design: Finding the balance between design lift and structural stiffness

International Nuclear Information System (INIS)

Bak, Christian; Gaudern, Nicholas; Zahle, Frederik; Vronsky, Tomas

2014-01-01

When upscaling wind turbine blades there is an increasing need for high levels of structural efficiency. In this paper the relationships between the aerodynamic characteristics; design lift and lift-drag ratio; and the structural characteristics were investigated. Using a unified optimization setup, airfoils were designed with relative thicknesses between 18% and 36%, a structural box height of 85% of the relative thickness, and varying box widths in chordwise direction between 20% and 40% of the chord length. The results from these airfoil designs showed that for a given flapwise stiffness, the design lift coefficient increases if the box length reduces and at the same time the relative thickness increases. Even though the conclusions are specific to the airfoil design approach used, the study indicated that an increased design lift required slightly higher relative thickness compared to airfoils with lower design lift to maintain the flapwise stiffness. Also, the study indicated that the lift-drag ratio as a function of flapwise stiffness was relatively independent of the airfoil design with a tendency that the lift-drag ratio decreased for large box lengths. The above conclusions were supported by an analysis of the three airfoil families Riso-C2, DU and FFA, where the lift-drag ratio as a function of flapwise stiffness was decreasing, but relatively independent of the airfoil design, and the design lift coefficient was varying depending on the design philosophy. To make the analysis complete also design lift and lift- drag ratio as a function of edgewise and torsional stiffness were shown

Soccer Ball Lift Coefficients via Trajectory Analysis

Science.gov (United States)

Goff, John Eric; Carre, Matt J.

2010-01-01

We performed experiments in which a soccer ball was launched from a machine while two high-speed cameras recorded portions of the trajectory. Using the trajectory data and published drag coefficients, we extracted lift coefficients for a soccer ball. We determined lift coefficients for a wide range of spin parameters, including several spin…

VII international district heating conference

International Nuclear Information System (INIS)

1988-01-01

The proceedings of the 7th International District Heating Conference contain the full texts of the 89 presented papers of which 11 fall under the INIS Subject Scope. The conference met in seven sessions and dealt with the following problem areas: design and optimization of systems of district heating, integration of the power system and the district heating systems, cooperation of nuclear and fossil burning sources in district heating systems, the use of specific nuclear power plants for heating purposes, questions of the control of systems of district heating, the development of components of heating networks, the reliability and design of heat supply pipes. (Z.M.)

Neurologic disorders associated with weight lifting and bodybuilding.

Science.gov (United States)

Busche, Kevin

2009-02-01

Weight lifting and other forms of strength training are becoming more common because of an increased awareness of the need to maintain individual physical fitness. Emergency room data indicate that injuries caused by weight training have become more universal over time, likely because of increased participation rates. Neurologic injuries can result from weight lifting and related practices. Although predominantly peripheral nervous system injuries have been described, central nervous system disease may also occur. This article illustrates the types of neurologic disorders associated with weight lifting.

The 35th JAIF annual conference

International Nuclear Information System (INIS)

2003-01-01

The JAIF (Japan Atomic Industrial Forum, INC) conference was opened at Oomiya Sonic City- Sonic City Hole, Saitama, Japan from April 22 to 24, 2002. Main theme was nuclear power in the changing socio-political environment-challenges for the future. The conference consisted of six parts such as opening session, session 1: energy policy of the 21st century and nuclear power, session 2: tasks for metropolitan areas and regions with nuclear facilities, session 3: why plutonium recycling? , session 4: contribution of nuclear power under the new socio-economic environment and session 5: to shape the future of nuclear power: development of advanced and innovative reactors. Session 2 to 4 was panel discussion. The other meeting for citizens and Youth Forum was hold and cinemas of nuclear power were shown. 14 speakers from many countries gave a lecture, 16 persons were panelers and 4 commentators. (S.Y.)

Lifting Safety: Tips To Help Prevent Back Injuries

Science.gov (United States)

... Prevent Back Injuries Lifting Safety: Tips to Help Prevent Back Injuries Share Print Back injuries are common problems at work, home, and play. They can be caused by accidents or improper lifting technique. Below are tips to ...

Evaluation of ceiling lifts in health care settings: patient outcome and perceptions.

Science.gov (United States)

Alamgir, Hasanat; Li, Olivia Wei; Gorman, Erin; Fast, Catherine; Yu, Shicheng; Kidd, Catherine

2009-09-01

Ceiling lifts have been introduced into health care settings to reduce manual patient lifting and thus occupational injuries. Although growing evidence supports the effectiveness of ceiling lifts, a paucity of research links indicators, such as quality of patient care or patient perceptions, to the use of these transfer devices. This study explored the relationship between ceiling lift coverage rates and measures of patient care quality (e.g., incidence of facility-acquired pressure ulcers, falls, urinary infections, urinary incontinence, and assaults [patient to staff] in acute and long-term care facilities), as well as patient perceptions of satisfaction with care received while using ceiling lifts in a complex care facility. Qualitative semi-structured interviews were used to generate data. A significant inverse relationship was found between pressure ulcer rates and ceiling lift coverage; however, this effect was attenuated by year. No significant relationships existed between ceiling lift coverage and patient outcome indicators after adding the "year" variable to the model. Patients generally approved of the use of ceiling lifts and recognized many of the benefits. Ceiling lifts are not detrimental to the quality of care received by patients, and patients prefer being transferred by ceiling lifts. The relationship between ceiling lift coverage and pressure ulcer rates warrants further investigation. Copyright (c) 2009, SLACK Incorporated.

Lift mechanics of downhill skiing and snowboarding.

Science.gov (United States)

Wu, Qianhong; Igci, Yesim; Andreopoulos, Yiannis; Weinbaum, Sheldon

2006-06-01

This study is conducted to develop a simplified mathematical model to describe the lift mechanics of downhill skiing and snowboarding, where the lift contributions due to both the transiently trapped air and the compressed solid phase (snow crystals) are determined. To our knowledge, this is the first time that anyone has attempted to realistically estimate the relative contribution of the transiently trapped air to the total lift in skiing and snowboarding. The model uses Shimizu's empirical relation to predict the local variation in Darcy permeability due to the compression of the solid phase. The forces and moments on the skier or snowboarder are used to predict the angle of attack of the planing surface, the penetration depth at the leading edge, and the shift in the center of pressure for two typical snow types, fresh and wind-packed snow. We present numerical solutions for snowboarding and asymptotic analytic solutions for skiing for the case where there are no edging or turning maneuvers. The force and moment balance are then used to develop a theory for control and stability in response to changes in the center of mass as the individual shifts his/her weight. Our model predicts that for fine-grained, windpacked snow that when the velocity (U) of the snowboarder or skier is 20 m.s, approximately 50% of the total lift force is generated by the trapped air for snowboarding and 40% for skiing. For highly permeable fresh powder snow, the lift contribution from the pore air pressure drops substantially. This paper develops a new theoretical framework for analyzing the lift mechanics and stability of skis and snowboards that could have important applications in future ski and snowboard design.

Development of nuclear power

Energy Technology Data Exchange (ETDEWEB)

NONE

1962-01-15

An extensive discussion of problems concerning the development of nuclear power took place at the fifth regular session of the IAEA General Conference in September-October 1961. Not only were there many references in plenary meetings to the nuclear power plans of Member States, but there was also a more specific and detailed debate on the subject, especially on nuclear power costs, in the Program, Technical and Budget Committee of the Conference. The Conference had before it a report from the Board of Governors on the studies made by the Agency on the economics of nuclear power. In addition, it had been presented with two detailed documents, one containing a review of present-day costs of nuclear power and the other containing technical and economic information on several small and medium-sized power reactors in the United States. The Conference was also informed of the report on methods of estimating nuclear power costs, prepared with the assistance of a panel of experts convened by the Agency, which was reviewed in the July 1961 issue of this Bulletin

Development of nuclear power

International Nuclear Information System (INIS)

1962-01-01

An extensive discussion of problems concerning the development of nuclear power took place at the fifth regular session of the IAEA General Conference in September-October 1961. Not only were there many references in plenary meetings to the nuclear power plans of Member States, but there was also a more specific and detailed debate on the subject, especially on nuclear power costs, in the Program, Technical and Budget Committee of the Conference. The Conference had before it a report from the Board of Governors on the studies made by the Agency on the economics of nuclear power. In addition, it had been presented with two detailed documents, one containing a review of present-day costs of nuclear power and the other containing technical and economic information on several small and medium-sized power reactors in the United States. The Conference was also informed of the report on methods of estimating nuclear power costs, prepared with the assistance of a panel of experts convened by the Agency, which was reviewed in the July 1961 issue of this Bulletin

Lift hysteresis at stall as an unsteady boundary-layer phenomenon

Science.gov (United States)

Moore, Franklin K

1956-01-01

Analysis of rotating stall of compressor blade rows requires specification of a dynamic lift curve for the airfoil section at or near stall, presumably including the effect of lift hysteresis. Consideration of the magnus lift of a rotating cylinder suggests performing an unsteady boundary-layer calculation to find the movement of the separation points of an airfoil fixed in a stream of variable incidence. The consideration of the shedding of vorticity into the wake should yield an estimate of lift increment proportional to time rate of change of angle of attack. This increment is the amplitude of the hysteresis loop. An approximate analysis is carried out according to the foregoing ideas for a 6:1 elliptic airfoil at the angle of attack for maximum lift. The assumptions of small perturbations from maximum lift are made, permitting neglect of distributed vorticity in the wake. The calculated hysteresis loop is counterclockwise. Finally, a discussion of the forms of hysteresis loops is presented; and, for small reduced frequency of oscillation, it is concluded that the concept of a viscous "time lag" is appropriate only for harmonic variations of angle of attack with time at mean conditions other than maximum lift.

DEWEK '98: 4. German wind power conference; DEWEK '98: 4. Deutsche Windenergie-Konferenz. Tagungsband

Energy Technology Data Exchange (ETDEWEB)

Gerdes, B [ed.

1999-07-01

The conference report comprises 90 papers and posters on the following subjects: 1. Technological developments (e.g. use of adaptive structures systems, active stalle wind power systems, systems for early detection of errors); 2. Design and optimisation; 3. Wind forecasts; 4. Operation analyses (e.g. active and passive stall, collective loads, wind power systems in cold climates); 5. Wind power systems and the environment; 6. Offshore wind power generation; 7. Electric characteristics (e.g. modelling of flicker, energy conditioning in distribution systems with a high wind power share); 8. Economic efficiency (e.g. economic efficiency of offshore wind parks on the North Sea coast); 9. Network quality; 10. Rotor development (e.g. noise reduction); 11. Certification and methods of measurement. [German] Der Tagungsband enhaelt 90 Fach- und Posterbeitraege, die sich mit den folgenden Schwerpunkten befassen: 1. Technologische Entwicklungen (z.B. Einsatz von adaptiven Struktursystemen; Active-Stall-WKA; Fehlerfrueherkennungssystemen). 2. Auslegung und Optimierung. 3. Windprognosen. 4. Betriebsanalysen (z.B. Aktive Stall/Passive Stall im Vergleich; Lastkollektive von WKA; WKA in kaltem Klima). 5. Windenergieanlagen und Umwelt. 6. Offshore-Windenergienutzung. 7. Elektrische Eigenschaften (z.B. Modellierung des 'Flickerverhaltens' von WKA; Energiekonditionierung in Verteilnetzen mit hohem Windenergieanteil). 8. Wirtschaftlichkeit (z.B. Wirtschaftlichkeit von Offshore-Windparks der Norddeutschen Kuestenlinie). 9. Netzqualitaet. 10. Rotorentwicklung (z.B. Reduzierung der Schallabstrahlung von WKAs). 11. Zertifizierung von Messmethoden. (AKF)

Quadratic Interpolation and Linear Lifting Design

Directory of Open Access Journals (Sweden)

Joel Solé

2007-03-01

Full Text Available A quadratic image interpolation method is stated. The formulation is connected to the optimization of lifting steps. This relation triggers the exploration of several interpolation possibilities within the same context, which uses the theory of convex optimization to minimize quadratic functions with linear constraints. The methods consider possible knowledge available from a given application. A set of linear equality constraints that relate wavelet bases and coefficients with the underlying signal is introduced in the formulation. As a consequence, the formulation turns out to be adequate for the design of lifting steps. The resulting steps are related to the prediction minimizing the detail signal energy and to the update minimizing the l2-norm of the approximation signal gradient. Results are reported for the interpolation methods in terms of PSNR and also, coding results are given for the new update lifting steps.

Advanced power assessment for Czech lignite, Task 3.6, Part 2. The 2nd international conference on energy and environment: Transitions in East Central Europe

Energy Technology Data Exchange (ETDEWEB)

Sondreal, E.A.; Mann, M.D.; Weber, G.W.; Young, B.C.

1995-12-01

On November 1-5, 1994, the Energy & Environmental Research Center (EERC) and Power Research Institute of Prague cosponsored their second conference since 1991 in the Czech Republic, entitled ``Energy and Environment: Transitions in East Central Europe.`` This conference was a continuation of the EERC`s joint commitment, initiated in 1190, to facilitate solutions to short- and long-term energy and environmental problems in East Central Europe. Production of energy from coal in an environmentally acceptable manner is a critical issue facing East Central Europe, because the region continues to rely on coal as its primary energy source. The goal of the conference was to develop partnerships between industry, government, and the research community in East Central Europe and the United States to solve energy and environmental issues in a manner that fosters economic development. Among the topics addressed at the conference were: conventional and advanced energy generation systems; economic operation of energy systems; air pollution controls; power system retrofitting and repowering, financing options; regulatory issues; energy resource options; waste utilization and disposal; and long-range environmental issues. Selected papers in the proceedings have been processed separately for inclusion in the Energy Science and Technology database.

LIFT11 linnas

Index Scriptorium Estoniae

2010-01-01

Tallinn 2011 programmi kuuluva installatsioonide festivali "Lift11" avalikule ideekonkursile esitati 129 tööd, välja valiti 17. Tutvustatakse Maarja Kase ja Ralf Lõokese tööd "L", Tomomi Hayashi tööd "Merele!", Toomas Paaveri, Teele Pehki ja Triin Talki tööd "Kalarand"

Lifting bloody footwear impressions using alginate casts followed by chemical enhancement.

Science.gov (United States)

Wiesner, Sarena; Izraeli, Elad; Shor, Yaron; Domb, Avi

2013-05-01

A method for lifting bloody footwear impressions using alginate casts and enhancing the lifted impressions with amido black is presented. On rough or dark substrates, background interferences may conceal significant details of footwear impressions. Illumination with alternative light sources and chemically enhancing the bloody footwear impressions may reveal additional details, but sometimes, lifting footwear impressions prior to enhancing is the only way to expose hidden details (by using blood reagents not adequate on the original). Several cast formulations were tested for lifting the footwear impressions. The best results were achieved using Aroma fine®. Enhancement of the footwear impressions was attempted with several reagents prior to lifting, during the casting process, and on the lifted footwear impressions. Applying amido black to footwear impressions lifted with alginate produced the sharpest and most detailed footwear impressions. Alginate castings followed by chemical enhancement with amido black may produce high-quality footwear impressions for comparison. © 2013 American Academy of Forensic Sciences.

Factors associated with high physical exertion during manual lifting

DEFF Research Database (Denmark)

Andersen, Lars L.; Sundstrup, Emil; Brandt, Mikkel

2018-01-01

BACKGROUND: High physical exertion during work is a risk factor for back pain and long-term sickness absence. OBJECTIVE: To investigate which factors are associated with physical exertion during manual lifting. METHODS: From 14 workplaces across Denmark, 200 blue-collar workers reported perceived...... physical exertion (Borg-CR10) during manual lifting from floor to table height of 5, 10, 20 and 30 kg at the beginning and end of the working day. The workers also responded to a questionnaire and went through testing of isometric back muscle strength. Associations were modelled using logistic regression...... during manual lifting in blue-collar workers. These factors should be considered when planning work with manual lifting for individual workers....

Building on our past... building for the future. 33rd Annual Canadian Nuclear Society conference and 36th CNS/CNA student conference

International Nuclear Information System (INIS)

2012-01-01

The 33rd Annual Canadian Nuclear Society Conference and 36th CNS/CNA Student Conference was held in Saskatoon, Saskatchewan, Canada on June 10-13, 2012. With the theme of the conference, 'Building on our Past... Building for the Future', the conference specifically noted the 50th anniversary of the first-nuclear-produced electricity in Canada by the small Nuclear Power Demonstration (NPD) plant on June 4, 1962 and the 60th anniversary of the creation of Atomic Energy of Canada Limited in April 1952. The conference brought together over 360 delegates for the technical sessions with very broad subject matter of: physics, environment and waste management, safety and licensing, life extension, fusion technology, fuel and advanced reactors, reactor materials, uranium mining, I and C process, and, thermalhydraulics. Two plenary sessions focussed on: Small Modular Reactors; and, radioisotopes primarily for medical applications. The student conference was well attended with plenary sessions focussing on: Nuclear Industry Power Developments: The Renaissance; and a panel discussion on the overview of the proposed refurbishment of the Darlington four-unit station.

UF{sub 6} cylinder lifting equipment enhancements

Energy Technology Data Exchange (ETDEWEB)

Hortel, J.M. [Martin Marietta Energy Systems, Inc., Piketon, OH (United States)

1991-12-31

This paper presents numerous enhancements that have been made to the Portsmouth lifting equipment to ensure the safe handling of cylinders containing liquid uranium hexafluoride (UF{sub 6}). The basic approach has been to provide redundancy to all components of the lift path so that any one component failure would not cause the load to drop or cause any undesirable movement.

TMI-2 reactor vessel plenum final lift

International Nuclear Information System (INIS)

Wilson, D.C.

1986-01-01

Removal of the plenum assembly from the TMI-2 reactor vessel was necessary to gain access to the core region for defueling. The plenum was lifted from the reactor vessel by the polar crane using three specially designed pendant assemblies. It was then transferred in air to the flooded deep end of the refueling canal and lowered onto a storage stand where it will remain throughout the defueling effort. The lift and transfer were successfully accomplished on May 15, 1985 in just under three hours by a lift team located in a shielded area within the reactor building. The success of the program is attributed to extensive mockup and training activities plus thorough preparations to address potential problems. 54 refs

78 FR 38311 - Reliability Technical Conference Agenda

Science.gov (United States)

2013-06-26

... issues related to the reliability of the Bulk-Power System. The agenda for this conference is attached... Reliability Technical Docket No. AD13-6-000 Conference. North American Electric Docket No. RC11-6-004 Reliability Corporation. North American Electric Docket No. RR13-2-000 Reliability Corporation. Not...

FREIGHT CONTAINER LIFTING STANDARD

Energy Technology Data Exchange (ETDEWEB)

POWERS DJ; SCOTT MA; MACKEY TC

2010-01-13

This standard details the correct methods of lifting and handling Series 1 freight containers following ISO-3874 and ISO-1496. The changes within RPP-40736 will allow better reading comprehension, as well as correcting editorial errors.

Proceedings of the 20. annual CanWEA conference and trade show

International Nuclear Information System (INIS)

2000-01-01

Wind energy is the most competitive large-scale electricity alternative to hydro-electricity and natural gas. Approximately 10,000 MW of wind energy energy may be required in order to meet demand in Canada by 2010. This annual conference provided a forum for decision-makers, industry leaders, power marketers, and regulatory administrators to discuss methods of meeting Canada's future energy supplies. Financial and industrial challenges to the growth of the wind power industry were discussed. Market drivers for wind development in Canada were reviewed, as well as the global status of the wind power industry. Technological advances in wind power were assessed, and issues related to grid integration and reliability were discussed. The conference was divided into 3 sessions: (1) global status and future prospects; (2) the Canadian challenge and opportunity; and (3) the Canadian Wind Energy Association annual general meeting. The conference included a trade show with exhibitions of new technologies related to wind power. The conference featured 31 presentations, of which 3 have been catalogued separately for inclusion in this database. refs., tabs., figs

Two-dimensional unsteady lift problems in supersonic flight

Science.gov (United States)

Heaslet, Max A; Lomax, Harvard

1949-01-01

The variation of pressure distribution is calculated for a two-dimensional supersonic airfoil either experiencing a sudden angle-of-attack change or entering a sharp-edge gust. From these pressure distributions the indicial lift functions applicable to unsteady lift problems are determined for two cases. Results are presented which permit the determination of maximum increment in lift coefficient attained by an unrestrained airfoil during its flight through a gust. As an application of these results, the minimum altitude for safe flight through a specific gust is calculated for a particular supersonic wing of given strength and wing loading.

Lifted Java: A Minimal Calculus for Translation Polymorphism

DEFF Research Database (Denmark)

Ingesman, Matthias Diehn; Ernst, Erik

2011-01-01

To support roles and similar notions involving multiple views on an object, languages like Object Teams and CaesarJ include mechanisms known as lifting and lowering. These mechanisms connect pairs of objects of otherwise unrelated types, and enables programmers to consider such a pair almost...... of translation polymorphism has not been proved. This paper presents a simple model that extends Featherweight Java with the core operations of translation polymorphism, provides a Coq proof that its type system is sound, and shows that the ambiguity problem associated with the so-called smart lifting mechanism...... can be eliminated by a very simple semantics for lifting....

How to lift a box that is too large to fit between the knees

NARCIS (Netherlands)

Kingma, I.; Faber, G.S.; van Dieen, J.H.

2010-01-01

Many studies compared lifting techniques such as stoop and squat lifting. Results thus far show that when lifting a wide load, high back loads result, irrespective of the lifting technique applied. This study compared four lifting techniques in 11 male subjects lifting wide loads. One of these

Clinical Comparison of Sinus Lift via Summers Osteotomy and Piezosurgery

Directory of Open Access Journals (Sweden)

Mehrdad Radvar

2017-12-01

Full Text Available Introduction: Sinus lift is a process that could be performed by two methods. In the closed sinus lift, hybrid materials enter a suitable position through a created cavity. Afterwards, the materials are pressed without damaging the sinus membrane, and the implants are usually placed at the same time. Closed sinus lift is carried out via osteotomy and piezosurgery, and each of the techniques has certain advantages and limitations. The present study aimed to compare the clinical results of closed sinus lift using the summers osteotomy and piezosurgery. Materials and Methods: In this study, 20 patients requiring dental implants in the posterior segment of the maxilla via sinus lift surgery were randomly divided into two groups. The first group received piezosurgery, and the second group underwent summers osteotomy for sinus lift. Postoperative Schneiderian membrane perforation, inflammation, pain, bone gain, and bone loss were compared between the groups six months after the surgery using Mann-Whitney U test and two-sample t-test. Results: In the groups receiving piezosurgery and summers osteotomy, mean sinus lift was 3.6±0.9 and 4.0±2.2 mm, pain score was 1.1±1.2 and 0.9±0.8, bone gain was 2.2±0.8 and 3.1±1.3 mm, and crestal bone loss was 1.1±1.2 and 0.9±0.8 mm, respectively. Moreover, no Schneiderian membrane perforation was observed in the two methods, and the differences between the groups were not considered significant (P>0.05. Conclusion: According to the results, the clinical outcomes of piezosurgery in sinus lift are similar to those of summers osteotomy. Therefore, piezosurgery could be a proper alternative to summers osteotomy in sinus lift surgery.

Performance and Vibration Analyses of Lift-Offset Helicopters

Directory of Open Access Journals (Sweden)

Jeong-In Go

2017-01-01

Full Text Available A validation study on the performance and vibration analyses of the XH-59A compound helicopter is conducted to establish techniques for the comprehensive analysis of lift-offset compound helicopters. This study considers the XH-59A lift-offset compound helicopter using a rigid coaxial rotor system as a verification model. CAMRAD II (Comprehensive Analytical Method of Rotorcraft Aerodynamics and Dynamics II, a comprehensive analysis code, is used as a tool for the performance, vibration, and loads analyses. A general free wake model, which is a more sophisticated wake model than other wake models, is used to obtain good results for the comprehensive analysis. Performance analyses of the XH-59A helicopter with and without auxiliary propulsion are conducted in various flight conditions. In addition, vibration analyses of the XH-59A compound helicopter configuration are conducted in the forward flight condition. The present comprehensive analysis results are in good agreement with the flight test and previous analyses. Therefore, techniques for the comprehensive analysis of lift-offset compound helicopters are appropriately established. Furthermore, the rotor lifts are calculated for the XH-59A lift-offset compound helicopter in the forward flight condition to investigate the airloads characteristics of the ABC™ (Advancing Blade Concept rotor.

Summaries of the thirteenth annual Canadian independent power conference and trade show : From theory to action: bringing fresh investment to the sector

International Nuclear Information System (INIS)

Eggertson, W.; McArthur, D.; Kishewitsch, S.

2002-05-01

This conference hosted by the Independent Power Producers' Society of Ontario, acquired an added impetus with the preparations under way for the opening of the Ontario electricity market to competition, scheduled for 2002. The speakers, over 30 of them, discussed the various aspects related to investment in the Ontario sector. The topics discussed were as follows: (1) what is needed to really get Ontario's market moving, (2) the regulator's role in facilitating competition and investment, (3) the regulator's role and the status of major capacity, (4) tax reforms proposed by the Canadian Electricity Association (CEA) and the Independent Power Producers' Society of Ontario to encourage investment, (5) achieving healthy competition, (6) addressing market behaviour: compliance and enforcement, (7) workshop on the new emission trading system, (8) improving environmental performance, (9) power purchasers' panel, (10) transmission within Ontario and at its borders, and (11) the shape of the future: maximizing on promise and opportunity. This conference provided an ideal forum for all independent producers to discuss issues and share ideas. refs., tabs., figs

Functional residual capacity increase during laparoscopic surgery with abdominal wall lift

Directory of Open Access Journals (Sweden)

Hiroshi Ueda

Full Text Available Abstract Background and objectives: The number of laparoscopic surgeries performed is increasing every year and in most cases the pneumoperitoneum method is used. One alternative is the abdominal wall lifting method and this study was undertaken to evaluate changes of functional residual capacity during the abdominal wall lift procedure. Methods: From January to April 2013, 20 patients underwent laparoscopic cholecystectomy at a single institution. All patients were anesthetized using propofol, remifentanil and rocuronium. FRC was measured automatically by Engstrom Carestation before the abdominal wall lift and again 15 minutes after the start of the procedure. Results: After abdominal wall lift, there was a significant increase in functional residual capacity values (before abdominal wall lift 1.48 × 103 mL, after abdominal wall lift 1.64 × 103 mL (p < 0.0001. No complications such as desaturation were observed in any patient during this study. Conclusions: Laparoscopic surgery with abdominal wall lift may be appropriate for patients who have risk factors such as obesity and respiratory disease.

The Revolutionary Vertical Lift Technology (RVLT) Project

Science.gov (United States)

Yamauchi, Gloria K.

2018-01-01

The Revolutionary Vertical Lift Technology (RVLT) Project is one of six projects in the Advanced Air Vehicles Program (AAVP) of the NASA Aeronautics Research Mission Directorate. The overarching goal of the RVLT Project is to develop and validate tools, technologies, and concepts to overcome key barriers for vertical lift vehicles. The project vision is to enable the next generation of vertical lift vehicles with aggressive goals for efficiency, noise, and emissions, to expand current capabilities and develop new commercial markets. The RVLT Project invests in technologies that support conventional, non-conventional, and emerging vertical-lift aircraft in the very light to heavy vehicle classes. Research areas include acoustic, aeromechanics, drive systems, engines, icing, hybrid-electric systems, impact dynamics, experimental techniques, computational methods, and conceptual design. The project research is executed at NASA Ames, Glenn, and Langley Research Centers; the research extensively leverages partnerships with the US Army, the Federal Aviation Administration, industry, and academia. The primary facilities used by the project for testing of vertical-lift technologies include the 14- by 22-Ft Wind Tunnel, Icing Research Tunnel, National Full-Scale Aerodynamics Complex, 7- by 10-Ft Wind Tunnel, Rotor Test Cell, Landing and Impact Research facility, Compressor Test Facility, Drive System Test Facilities, Transonic Turbine Blade Cascade Facility, Vertical Motion Simulator, Mobile Acoustic Facility, Exterior Effects Synthesis and Simulation Lab, and the NASA Advanced Supercomputing Complex. To learn more about the RVLT Project, please stop by booth #1004 or visit their website at https://www.nasa.gov/aeroresearch/programs/aavp/rvlt.

Press conference of the 15 october 2002; Conference de presse du 15 octobre 2002

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-10-01

Facing the public hostile purposes of october 2002, concerning the renewable energies, Andre Antolini, President of the renewable energies syndicate, proposed a press conference to give information, data and realizations on the renewable energies. The text of the conference is presented, as data on employment, biofuels, the wind energy, the hydro-electricity the greenhouse effect fight, the public opinion, the solar heating, the photovoltaic and the future projects and electric power supply for 2010. (A.L.B.)

Lifting Wing in Constructing Tall Buildings —Aerodynamic Testing

Directory of Open Access Journals (Sweden)

Ian Skelton

2014-05-01

Full Text Available This paper builds on previous research by the authors which determined the global state-of-the-art of constructing tall buildings by surveying the most active specialist tall building professionals around the globe. That research identified the effect of wind on tower cranes as a highly ranked, common critical issue in tall building construction. The research reported here presents a design for a “Lifting Wing,” a uniquely designed shroud which potentially allows the lifting of building materials by a tower crane in higher and more unstable wind conditions, thereby reducing delay on the programmed critical path of a tall building. Wind tunnel tests were undertaken to compare the aerodynamic performance of a scale model of a typical “brick-shaped” construction load (replicating a load profile most commonly lifted via a tower crane against the aerodynamic performance of the scale model of the Lifting Wing in a range of wind conditions. The data indicate that the Lifting Wing improves the aerodynamic performance by a factor of up to 50%.

Testing two novel stump-lifting heads in a final felling Norway spruce stand

Energy Technology Data Exchange (ETDEWEB)

Kaerhae, K. (Metsaeteho Oy, Helsinki (Finland)), Email: kalle.karha@metsateho.fi; Mutikainen, A. (TTS Research, Rajamaeki (Finland)), Email: arto.mutikainen@tts.fi

2009-07-01

The use of stump and root wood chips has increased very rapidly in the 21st century in Finland: in the year 2000, the total consumption of stump wood chips for energy generation was 10 GWh, while in 2008 it was around 1.2 TWh. Metsaeteho Oy and TTS Research tested two new stump-lifting devices for lifting stumps in a final felling Norway spruce (picea abies) stand. In the time study with the Vaekevae Stump Processor lifting head, the productivity of stump lifting was 7,5 m3 / E{sub 0}-hour when lifting spruce stumps with a diameter of 30 cm from clayey soil, and 8.3 m3 /E{sub 0}-hour when lifting spruce stumps from sandy soil. When lifting stumps with a diameter of 40 cm, the stump-lifting productivity was 9.0 m3 /E{sub 0}-h (clay) and 10,5 m3 / E{sub 0}-h (sand). The results of this relatively restricted test indicated that the Vaekevae Stump Processor is s reliable and effective stump-lifting head that enables the harvesting of high-quality stump raw material for energy generation. The stump lifting productivity of the other lifting head (Jaervinen) was lower than that of the Vaekevae Strump Processor. Some development suggestions for the Jaervinen lifting head were presented and discussed. (orig.)

Lift11 / Ingrid Ruudi

Index Scriptorium Estoniae

Ruudi, Ingrid, 1978-

2010-01-01

23. augustist 11. oktoobrini 2010 toimuvast konkursist, mille eesmärk on leida kultuuripealinna üritusena toimuva linnainstallatsioonide festivali "Lift11" tarvis installatsioonide ideekavandeid. Festivali kuraatorid on kunstiteadlased Maarin Mürk ja Ingrid Ruudi ning arhitektid Margit Aule ja Margit Argus

Proceedings of the 7. Nuclear Science and Technology Conference

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-01

The 7. conference on nuclear science and technology was held on 1-2 December 1998 in Bangkok. This conference contain papers on non-power applications of nuclear technology in medicine, agriculture and industry. These application include irradiation of food for disinfestation; tram technologies used in diagnosis and therapy and radiation chemistry important to industrial processes. Some technologies which evolved from the development of nuclear power industry are also discussed

Comparison of Methods of Teaching Children Proper Lifting ...

African Journals Online (AJOL)

Objective: This study was designed to determine the effects of three teaching methods on children\\'s ability to demonstrate and recall their mastery of proper lifting techniques. Method: Ninety-three primary five and six public school children who had no knowledge of proper lifting technique were assigned into three equal ...

EFFECT OF HEEL LIFTS ON PATELLOFEMORAL JOINT STRESS DURING RUNNING.

Science.gov (United States)

Mestelle, Zachary; Kernozek, Thomas; Adkins, Kelly S; Miller, Jessica; Gheidi, Naghmeh

2017-10-01

Patellofemoral pain is a debilitating injury for many recreational runners. Excessive patellofemoral joint stress may be the underlying source of pain and interventions often focus on ways to reduce patellofemoral joint stress. Heel lifts have been used as an intervention within Achilles tendon rehabilitation programs and to address leg length discrepancies. The purpose of this study was to examine the effect of running with heel lifts on patellofemoral joint stress, patellofemoral stress impulse, quadriceps force, step length, cadence, and other related kinematic and spatiotemporal variables. A repeated-measures research design. Sixteen healthy female runners completed five running trials in a controlled laboratory setting with and without 11mm heel lifts inserted in a standard running shoe. Kinetic and kinematic data were used in combination with a static optimization technique to estimate individual muscle forces. These data were inserted into a patellofemoral joint model which was used to estimate patellofemoral joint stress and other variables during running. When running with heel lifts, peak patellofemoral joint stress and patellofemoral stress impulse were reduced by a 4.2% (p=0.049) and 9.3% (p=0.002). Initial center of pressure was shifted anteriorly 9.1% when running with heel lifts (p0.05) were shown between conditions. Heel lift use resulted in decreased patellofemoral joint stress and impulse without associated changes in step length or frequency, or other variables shown to influence patellofemoral joint stress. The center of pressure at initial contact was also more anterior using heel lifts. The use of heel lifts may have therapeutic benefits for runners with patellofemoral pain if the primary goal is to reduce patellofemoral joint stress. 3b.

THE SHAPING OF SOME LIFTING AND TRANSPORTATION SYSTEMS, USING AUTODESK INVENTOR

Directory of Open Access Journals (Sweden)

URSE Cătălin

2011-11-01

Full Text Available The paper presents, through the use of Autodesk Inventor software package, several mechanisms from the structure of lifting and transportation machines, in this case lifting system with winch operated by screw,lifting system type with muffle with hook, respectively bridge crane type.

The 43rd JAIF annual conference

International Nuclear Information System (INIS)

2010-01-01

This CD-ROM includes the abstracts of JAIF annual conference held on April 20-22, 2010. Main theme was 'Major Pillar of Energy Supply and Global Warming Measures: Considering the Future of Nuclear Energy'. The conference consisted of three sessions. Each theme of these sessions are as follows; Session 1: 'How should nuclear power be positioned as a trump card for addressing climate change in political and social milieu?', Session 2: 'National perspectives on nuclear and energy policies toward the realization of their Nuclear Renaissance', Session 3: 'Here in Shimane, we think about the forty years back and future of the local community with nuclear power plants'. (J.P.N.)

2005 annual nuclear technology conference

International Nuclear Information System (INIS)

Anon.

2005-01-01

This year's Annual Nuclear Technology Conference of the Deutsches Atomforum and Kerntechnische Gesellschaft was held in Nuremberg on May 10-12, 2005. More than 1 100 participants from eighteen countries make this specialized event one of the largest international conventions in the field of the peaceful uses of nuclear power, whose attendance has steadily increased over the past few years. The first day of the conference was devoted to plenary lectures traditionally dealing mainly with political and economic problems of the use of nuclear power. The partner country of JK 2005 was Switzerland. Traditionally, the program of the three-day conference was organized in the proven format of plenary sessions on the first day, followed by technical sessions, specialized sessions, poster sessions, and special events on the following days. For the third time, the ''Nuclear Campus'' was organized which successfully made the world of nuclear technology transparent to high school and university students in lectures and an exhibition. The meeting was accompanied by a technical exhibition with meeting points of manufacturers, suppliers, and service industries. (orig.)

Laser-induced forward transfer (LIFT) of congruent voxels

Science.gov (United States)

Piqué, Alberto; Kim, Heungsoo; Auyeung, Raymond C. Y.; Beniam, Iyoel; Breckenfeld, Eric

2016-06-01

Laser-induced forward transfer (LIFT) of functional materials offers unique advantages and capabilities for the rapid prototyping of electronic, optical and sensor elements. The use of LIFT for printing high viscosity metallic nano-inks and nano-pastes can be optimized for the transfer of voxels congruent with the shape of the laser pulse, forming thin film-like structures non-lithographically. These processes are capable of printing patterns with excellent lateral resolution and thickness uniformity typically found in 3-dimensional stacked assemblies, MEMS-like structures and free-standing interconnects. However, in order to achieve congruent voxel transfer with LIFT, the particle size and viscosity of the ink or paste suspensions must be adjusted to minimize variations due to wetting and drying effects. When LIFT is carried out with high-viscosity nano-suspensions, the printed voxel size and shape become controllable parameters, allowing the printing of thin-film like structures whose shape is determined by the spatial distribution of the laser pulse. The result is a new level of parallelization beyond current serial direct-write processes whereby the geometry of each printed voxel can be optimized according to the pattern design. This work shows how LIFT of congruent voxels can be applied to the fabrication of 2D and 3D microstructures by adjusting the viscosity of the nano-suspension and laser transfer parameters.

Advances in Engineering Software for Lift Transportation Systems

Science.gov (United States)

Kazakoff, Alexander Borisoff

2012-03-01

In this paper an attempt is performed at computer modelling of ropeway ski lift systems. The logic in these systems is based on a travel form between the two terminals, which operates with high capacity cabins, chairs, gondolas or draw-bars. Computer codes AUTOCAD, MATLAB and Compaq-Visual Fortran - version 6.6 are used in the computer modelling. The rope systems computer modelling is organized in two stages in this paper. The first stage is organization of the ground relief profile and a design of the lift system as a whole, according to the terrain profile and the climatic and atmospheric conditions. The ground profile is prepared by the geodesists and is presented in an AUTOCAD view. The next step is the design of the lift itself which is performed by programmes using the computer code MATLAB. The second stage of the computer modelling is performed after the optimization of the co-ordinates and the lift profile using the computer code MATLAB. Then the co-ordinates and the parameters are inserted into a program written in Compaq Visual Fortran - version 6.6., which calculates 171 lift parameters, organized in 42 tables. The objective of the work presented in this paper is an attempt at computer modelling of the design and parameters derivation of the rope way systems and their computer variation and optimization.

Effect of hydrogen addition on autoignited methane lifted flames

KAUST Repository

Choin, Byung Chul; Chung, Suk-Ho

2012-01-01

Autoignited lifted flames in laminar jets with hydrogen-enriched methane fuels have been investigated experimentally in heated coflow air. The results showed that the autoignited lifted flame of the methane/hydrogen mixture, which had an initial

ALARA review for the deactivation of 105-N Lift Station

International Nuclear Information System (INIS)

Nellesen, A.L.

1997-01-01

This ALARA review provides a description of the engineering and administrative controls used to manage personnel exposure and to control contamination levels and airborne radioactivity concentrations, while removing water, sludge, stabilizing surfaces, and all other associated work involved in the deactivation of the 105-N Lift Station. The lift station was used as a sump and received contaminated water from the 105-N Fuel Storage Basin weirs and contaminated drains in the 105-N Building. During operation water from the lift station was pumped to the 1310-N and 1325-N cribs. Deactivation of the lift station is a critical step in completing the deactivation of N-Area

Performance investigations on modified vertical axis water turbine: Combination of lift and drag

Science.gov (United States)

Baumatary, Mithinga; Biswas, Angimitra; Misra, Rahul Dev

2018-04-01

Extracting energy from the water has been followed since decades due to environmental friendly. Now a days everyone is running after clean energy, therefore extracting energy from the water turbine is a good approach. The main idea of this study is to investigate the performance of a new design turbine which is a combination of the concepts of lift and drag turbine. The main purpose of the study is to accumulate maximum energy by considering advantages of two different types of turbine. The maximum coefficient of power is 0.141 at free stream velocity of 0.5 m/s. The modified new design turbine consist of straight section and the curve section. The length of the straight section influences the performance of the turbine. Investigation on the optimization of straight section has been carried out in this paper. As this type of turbine have opted the advantages of both lift and drag it has turned out to be fruitful.

iLift: A health behavior change support system for lifting and transfer techniques to prevent lower-back injuries in healthcare.

Science.gov (United States)

Kuipers, Derek A; Wartena, Bard O; Dijkstra, Boudewijn H; Terlouw, Gijs; van T Veer, Job T B; van Dijk, Hylke W; Prins, Jelle T; Pierie, Jean Pierre E N

2016-12-01

Lower back problems are a common cause of sick leave of employees in Dutch care homes and hospitals. In the Netherlands over 40% of reported sick leave is due to back problems, mainly caused by carrying out heavy work. The goal of the iLift project was to develop a game for nursing personnel to train them in lifting and transfer techniques. The main focus was not on testing for the effectiveness of the game itself, but rather on the design of the game as an autogenous trigger and its place in a behavioral change support system. In this article, the design and development of such a health behavior change support system is addressed, describing cycles of design and evaluation. (a) To define the problem space, use context and user context, focus group interviews were conducted with Occupational Therapists (n=4), Nurses (n=10) and Caregivers (n=12) and a thematic analysis was performed. We interviewed experts (n=5) on the subject of lifting and transferring techniques. (b) A design science research approach resulted in a playable prototype. An expert panel conducted analysis of video-recorded playing activities. (c) Field experiment: We performed a dynamic analysis in order to investigate the feasibility of the prototype through biometric data from player sessions (n=620) by healthcare professionals (n=37). (a) Occupational Therapists, Nurses and Caregivers did not recognise a lack of knowledge with training in lifting and transferring techniques. All groups considered their workload, time pressure and a culturally determined habit to place the patient's well being above their own as the main reason not to apply appropriate lifting and transferring techniques. This led to a shift in focus from a serious game teaching lifting and transferring techniques to a health behavior change support system containing a game with the intention to influence behavior. (b) Building and testing (subcomponents of) the prototype resulted in design choices regarding players perspective

Estimation of unsteady lift on a pitching airfoil from wake velocity surveys

Science.gov (United States)

Zaman, K. B. M. Q.; Panda, J.; Rumsey, C. L.

1993-01-01

The results of a joint experimental and computational study on the flowfield over a periodically pitched NACA0012 airfoil, and the resultant lift variation, are reported in this paper. The lift variation over a cycle of oscillation, and hence the lift hysteresis loop, is estimated from the velocity distribution in the wake measured or computed for successive phases of the cycle. Experimentally, the estimated lift hysteresis loops are compared with available data from the literature as well as with limited force balance measurements. Computationally, the estimated lift variations are compared with the corresponding variation obtained from the surface pressure distribution. Four analytical formulations for the lift estimation from wake surveys are considered and relative successes of the four are discussed.

Creating Learning at Conferences Through Participant Involvement

DEFF Research Database (Denmark)

Ravn, Ib; Elsborg, Steen

as a forum for learning, mutual inspiration and "human co-flourishing." We offer five design principles that specify how conferences may involve participants more and hence increase their learning. In the research and development effort reported here, our team collaborated with conference organizers......The typical conference is brimming with PowerPoint presentations that leave very little time for participant involvement. Students of learning have long abandoned the transfer model that underlies this massive show of one-way communication. We propose an alternative theory of the conference...... in Denmark to introduce a variety of simple learning techniques related to the design principles at thirty real conferences of some 100-200 participants each. We present twelve of these techniques and the data evaluating them and conclude that by spending a fraction of the time at a conference on involving...

Three-dimensional motion analysis of the lumbar spine during "free squat" weight lift training.

Science.gov (United States)

Walsh, James C; Quinlan, John F; Stapleton, Robert; FitzPatrick, David P; McCormack, Damian

2007-06-01

Heavy weight lifting using a squat bar is a commonly used athletic training exercise. Previous in vivo motion studies have concentrated on lifting of everyday objects and not on the vastly increased loads that athletes subject themselves to when performing this exercise. Athletes significantly alter their lumbar spinal motion when performing squat lifting at heavy weights. Controlled laboratory study. Forty-eight athletes (28 men, 20 women) performed 6 lifts at 40% maximum, 4 lifts at 60% maximum, and 2 lifts at 80% maximum. The Zebris 3D motion analysis system was used to measure lumbar spine motion. Exercise was performed as a "free" squat and repeated with a weight lifting support belt. Data obtained were analyzed using SAS. A significant decrease (P free squat or when lifting using a support belt in any of the groups studied. Weight lifting using a squat bar causes athletes to significantly hyperextend their lumbar spines at heavier weights. The use of a weight lifting support belt does not significantly alter spinal motion during lifting.

First-Order Twistor Lifts

Directory of Open Access Journals (Sweden)

Simões BrunoAscenso

2010-01-01

Full Text Available The use of twistor methods in the study of Jacobi fields has proved quite fruitful, leading to a series of results. L. Lemaire and J. C. Wood proved several properties of Jacobi fields along harmonic maps from the two-sphere to the complex projective plane and to the three- and four-dimensional spheres, by carefully relating the infinitesimal deformations of the harmonic maps to those of the holomorphic data describing them. In order to advance this programme, we prove a series of relations between infinitesimal properties of the map and those of its twistor lift. Namely, we prove that isotropy and harmonicity to first order of the map correspond to holomorphicity to first order of its lift into the twistor space, relatively to the standard almost complex structures and . This is done by obtaining first-order analogues of classical twistorial constructions.

First-Order Twistor Lifts

Directory of Open Access Journals (Sweden)

Bruno Ascenso Simões

2010-01-01

Full Text Available The use of twistor methods in the study of Jacobi fields has proved quite fruitful, leading to a series of results. L. Lemaire and J. C. Wood proved several properties of Jacobi fields along harmonic maps from the two-sphere to the complex projective plane and to the three- and four-dimensional spheres, by carefully relating the infinitesimal deformations of the harmonic maps to those of the holomorphic data describing them. In order to advance this programme, we prove a series of relations between infinitesimal properties of the map and those of its twistor lift. Namely, we prove that isotropy and harmonicity to first order of the map correspond to holomorphicity to first order of its lift into the twistor space, relatively to the standard almost complex structures J1 and J2. This is done by obtaining first-order analogues of classical twistorial constructions.

Shape memory alloy resetable spring lift for pedestrian protection

Science.gov (United States)

Barnes, Brian M.; Brei, Diann E.; Luntz, Jonathan E.; Strom, Kenneth; Browne, Alan L.; Johnson, Nancy

2008-03-01

Pedestrian protection has become an increasingly important aspect of automotive safety with new regulations taking effect around the world. Because it is increasingly difficult to meet these new regulations with traditional passive approaches, active lifts are being explored that increase the "crush zone" between the hood and rigid under-hood components as a means of mitigating the consequences of an impact with a non-occupant. Active lifts, however, are technically challenging because of the simultaneously high forces, stroke and quick timing resulting in most of the current devices being single use. This paper introduces the SMArt (Shape Memory Alloy ReseTable) Spring Lift, an automatically resetable and fully reusable device, which couples conventional standard compression springs to store the energy required for a hood lift, with Shape Memory Alloys actuators to achieve both an ultra high speed release of the spring and automatic reset of the system for multiple uses. Each of the four SMArt Device subsystems, lift, release, lower and reset/dissipate, are individually described. Two identical complete prototypes were fabricated and mounted at the rear corners of the hood, incorporated within a full-scale vehicle testbed at the SMARTT (Smart Material Advanced Research and Technology Transfer) lab at University of Michigan. Full operational cycle testing of a stationary vehicle in a laboratory setting confirms the ultrafast latch release, controlled lift profile, gravity lower to reposition the hood, and spring recompression via the ratchet engine successfully rearming the device for repeat cycles. While this is only a laboratory demonstration and extensive testing and development would be required for transition to a fielded product, this study does indicate that the SMArt Lift has promise as an alternative approach to pedestrian protection.

Nuclear the next generation. 34th Annual Canadian Nuclear Society conference and 37th CNS/CNA student conference

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-07-01

The 34th Annual Canadian Nuclear Society Conference and 37th CNS/CNA Student Conference was held in Toronto, Ontario, Canada on June 10-13, 2013. With the theme of the conference, 'Nuclear the Next Generation{sup ,} the conference actively engaged 400 participants in the many facets of this well-rum event. The conference combined excellent plenary speakers, a full set of technical papers, challenging student poster competitions, and interesting exhibits. The plenary session focussed on the themes: 'Nuclear Power - a Business Driver for the Next Generation'; and, 'Designing - the Next Generation'. The technical session titles were: Reactor and Radiation Physics; Environment and Spent Fuel Management; Operations and Maintenance; Fusion Science and Technology; Advanced Reactors and Fuels; Plant Life Extension, Refurbishment and Aging; Safety and Licensing; Chemistry and Materials; and, Thermalhydraulics. The student conference session was well attended and completed the 4 day event.

Study of lifting operation of a tripod foundation for offshore wind turbine

Science.gov (United States)

Zhu, H.; Li, L.; Ong, M. C.

2017-12-01

This study addresses numerical analysis of the installation of a tripod foundation using a heavy lift vessel (HLV). Limiting sea states are firstly predicted in the frequency domain based on crane tip vertical motions using linear transfer functions. Then, numerical modelling and simulations are carried out in the time domain to analyse the coupled dynamic system taking into consideration of the nonlinearities of the system. In time-domain analysis, two lifting phases are brought into focus, i.e., the lift-off and the lowering phases. For the lift-off phase, two scenarios are considered, i.e., lift-off from the own deck of the HLV and lift-off from a transport barge. Moreover, comparative studies using two types of installation vessels, a floating vessel and a Jack-up, are investigated for the lowering process. Critical responses including the motions of the tripod and the lift wire tensions are presented and compared under various environmental and loading conditions.

Knees Lifted High

Centers for Disease Control (CDC) Podcasts

The Eagle Books are a series of four books that are brought to life by wise animal characters - Mr. Eagle, Miss Rabbit, and Coyote - who engage Rain That Dances and his young friends in the joy of physical activity, eating healthy foods, and learning from their elders about health and diabetes prevention. Knees Lifted High gives children fun ideas for active outdoor play.

Mannesmann Demag crawler cranes give plants a big lift

International Nuclear Information System (INIS)

Anon.

1987-01-01

Preassembly of large reactor components reduces construction costs, but creates the need for cranes with larger lifting capacities. A German company is extending its range with a new crawler crane which will lift up to 1600t. (author)

Beams '96. Proceedings of the 11th international conference on high power particle beams. Vol. II

International Nuclear Information System (INIS)

Jungwirth, K.; Ullschmied, J.

1996-01-01

The scientific programme of the conference carved the physics and technology of intense beams of charged particles, from basic experimental and theoretical problems of beam generation, transport and interaction with various media, up to beam and pulsed power applications in science and in industry. The breakdown of the papers by main topical groups is as follows: radiation sources, Z-pinches, accelerate related topics, astrophysics, ICF, ION Beam Physics, ION DIODES, ION RINGS, Beam plasma systems, diagnostic and others. This volumes contains 160 contributions, out which 133 have been input to INIS

Beams `96. Proceedings of the 11th international conference on high power particle beams. Vol. II

Energy Technology Data Exchange (ETDEWEB)

Jungwirth, K.; Ullschmied, J. [eds.

1997-12-31

The scientific programme of the conference carved the physics and technology of intense beams of charged particles, from basic experimental and theoretical problems of beam generation, transport and interaction with various media, up to beam and pulsed power applications in science and in industry. The breakdown of the papers by main topical groups is as follows: radiation sources, Z-pinches, accelerate related topics, astrophysics, ICF, ION Beam Physics, ION DIODES, ION RINGS, Beam plasma systems, diagnostic and others. This volumes contains 160 contributions, out which 133 have been input to INIS.

Back muscle strength, lifting, and stooped working postures.

Science.gov (United States)

Poulsen, E; Jørgensen, K

1971-09-01

When lifting loads and working in a forward stooped position, the muscles of the back rather than the ligaments and bony structures of the spine should overcome the gravitational forces. Formulae, based on measurements of back muscle strength, for prediction of maximal loads to be lifted, and for the ability to sustain work in a stooped position, have been worked out and tested in practical situations. From tests with 50 male and female subjects the simplest prediction formulae for maximum loads were: max. load = 1.10 x isometric back muscle strength for men; and max. load = 0.95 x isometric back muscle strength - 8 kg for women. Some standard values for maximum lifts and permissible single and repeated lifts have been calculated for men and women separately and are given in Table 1. From tests with 65 rehabilitees it was found that the maximum isometric strength of the back muscles measured at shoulder height should exceed 2/3 of the body weight, if fatigue and/or pain in the back muscles is to be avoided during work in a standing stooped position.

An Extensional Characterization of Lambda-Lifting and Lambda-Dropping

DEFF Research Database (Denmark)

Danvy, Olivier

1999-01-01

Lambda-lifting and lambda-dropping respectively transform a block-structured functional program into recursive equations and vice versa. Lambda-lifting was developed in the early 80’s, whereas lambda-dropping is more recent. Both are split into an analysis and a transformation. Published work......, however, has only concentrated on the analysis parts. We focus here on the transformation parts and more precisely on their correctness, which appears never to have been proven. To this end, we define extensional versions of lambda-lifting and lambda-dropping and establish their correctness with respect...

Development of a Marine Propeller With Nonplanar Lifting Surfaces

DEFF Research Database (Denmark)

Andersen, Poul; Friesch, Jürgen; Kappel, Jens J.

2005-01-01

The principle of non-planar lifting surfaces is applied to the design of modern aircraft wings to obtain better lift to drag ratios. Whereas a pronounced fin or winglet at the wingtip has been developed for aircraft, the application of the nonplanar principle to marine propellers, dealt...... with in this paper, has led to the KAPPEL propeller with blades curved toward the suction side integrating the fin or winglet into the propeller blade. The combined theoretical, experimental, and practical approach to develop and design marine propellers with nonplanar lifting surfaces has resulted in propellers...

An Extensional Characterization of Lambda-Lifting and Lambda-Dropping

DEFF Research Database (Denmark)

Danvy, Olivier

1998-01-01

Lambda-lifting and lambda-dropping respectively transform a block-structured functional program into recursive equations and vice versa. Lambda-lifting was developed in the early 80’s, whereas lambda-dropping is more recent. Both are split into an analysis and a transformation. Published work......, however, has only concentrated on the analysis parts. We focus here on the transformation parts and more precisely on their correctness, which appears never to have been proven. To this end, we define extensional versions of lambda-lifting and lambda-dropping and establish their correctness with respect...

Aircraft Electric/Hybrid-Electric Power and Propulsion Workshop Perspective of the V/STOL Aircraft Systems Tech Committee

Science.gov (United States)

Hange, Craig E.

2016-01-01

This presentation will be given at the AIAA Electric Hybrid-Electric Power Propulsion Workshop on July 29, 2016. The workshop is being held so the AIAA can determine how it can support the introduction of electric aircraft into the aerospace industry. This presentation will address the needs of the community within the industry that advocates the use of powered-lift as important new technologies for future aircraft and air transportation systems. As the current chairman of the VSTOL Aircraft Systems Technical Committee, I will be presenting generalized descriptions of the past research in developing powered-lift and generalized observations on how electric and hybrid-electric propulsion may provide advances in the powered-lift field.

International Conference on Microelectronics, Electromagnetics and Telecommunications

CERN Document Server

Rao, N; Kumar, S; Raj, C; Rao, V; Sarma, G

2016-01-01

This volume contains 73 papers presented at ICMEET 2015: International Conference on Microelectronics, Electromagnetics and Telecommunications. The conference was held during 18 – 19 December, 2015 at Department of Electronics and Communication Engineering, GITAM Institute of Technology, GITAM University, Visakhapatnam, INDIA. This volume contains papers mainly focused on Antennas, Electromagnetics, Telecommunication Engineering and Low Power VLSI Design.

American power conference 2001 proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

Sessions included: distributed generation - trends and technologies; combustion modifications for NOx control; post combustion NOx control; repowering for the future; issues in development of new generation; taking a closer look at operation and maintenance; SCADA technology; customer/demand side management enters the trading area; managing feeder dynamics; keeping the lights on - power quality and reliability; merchant plant grid interconnection; optimising generation assets; power price spikes; e-commerce - from soup to nuts; and power generation market trends.

20th IEEE-NPSS Real Time Conference

CERN Document Server

2016-01-01

We invite you at the Centro Congressi “A. Luciani” in Padova for the 2016 Real Time Conference (RT2016). It will take place Monday 6 through Friday 10 June 2016, with optional pre-conference tutorials Sunday, June 5. Like the previous editions, RT2016 will be a multidisciplinary conference devoted to the latest developments on realtime techniques in the fields of Plasma and Nuclear Fusion, particle physics, nuclear physics and astrophysics, space science, accelerators, medical physics, nuclear power instrumentation and other radiation instrumentation.

Measurement and characterization of lift forces on drops and bubbles in microchannels

Science.gov (United States)

Stan, Claudiu; Guglielmini, Laura; Ellerbee, Audrey; Caviezel, Daniel; Whitesides, George; Stone, Howard

2013-11-01

The transverse motion of drops and bubbles within liquids flowing in pipes and channels is determined by the combination of several types of hydrodynamic lift forces with external forces. In microfluidic channels, lift forces have been used to position and sort particles with high efficiency and high accuracy. We measured lift forces on drops and bubbles and discriminated between different lift mechanisms under conditions characterized by low particle capillary numbers (0.0003 bubbles. We will present new experimental data that supports a dynamic interfacial mechanism for the second type of lift force, and discuss possible avenues for creating an analytical model for it.

Investigation and mapping of the requirements for lifting devices in a nuclear facility; Utredning och kartlaeggning av krav foer lyftanordningar inom kaernteknisk anlaeggning

Energy Technology Data Exchange (ETDEWEB)

Andersson, Kjell (Inspecta Sweden AB, Vaexjoe (Sweden))

2010-03-15

This technical report covers the investigation and identification of requirements for lifting devices in nuclear facilities. The report is divided into the following Section: 1. A mapping of the regulatory framework for nuclear hoists in Finland, Germany and USA. 2. A description of how the international legal framework is applied in for replacement or modernization of lifts in the Swedish nuclear power plants. 3. In Europe, the new harmonized standard has been developed for conventional hoists. The rules appear in the 'EN-13 001'. The study will illustrate these rules, and how they currently apply in the nuclear industry in Sweden. 4. A comparison between the IKH's lifting standards and EN13001 which differences are highlighted and explained

Proceedings of East Asia and Pacific area corrosion conference and expo: conference souvenir

International Nuclear Information System (INIS)

2011-01-01

The 19th annual conference being hosted by NACE International Gateway India Section (NIGIS) CORCON 2011 will feature technical symposia, interactive technical sessions and an expo. By promoting awareness and knowledge related to corrosion and its control through its educational programs and annual conferences, NIGIS reflects the mission and objectives of NACE International in India. The annual conference branded as 'CORCON', has emerged as the premier forum in India for Indian and overseas professionals wishing to interact on matters related to corrosion and its prevention. The technical symposia comprise a wide array of corrosion - related topics such as: Paints Coating and Lining, Materials and Composites, Inhibitors, MIC, Cathodic Protection, Failure Analysis, Inspection and Testing and covers sectors such as RCC and Infrastructure and Electric Power and Utilities. Papers relevant to INIS are indexed separately

Design of a large heat lift 40 K to 80 K pulse tube cryocooler for space applications

NARCIS (Netherlands)

Trollier, T.; Tanchon, J.; Buquet, J.; Ravex, A.; Charles, I.; Coynel, A.; Duband, L.; Ercolani, E.; Guillemet, L.; Mullié, J.; Dam, J.A.M.; Benschop, T.; Linder, M.; Miller, S.D.; Ross, Jr. R.G.

2007-01-01

A Large heat lift Pulse Tube Cooler (LPTC) is under development in partnership with AL/ DTA, CEA/SBT and THALES Cryogenics. The engineering model is expected to provide 2.3 W at 50 K at a 10 °C rejection temperature and 160 watts of electrical input power to the compressor. The split coaxial design

Lifting device for drilling rods

Energy Technology Data Exchange (ETDEWEB)

Radzivilovich, L L; Laptev, A G; Lipkovich, V A

1982-01-01

A lifter is proposed for drilling rods including a spacer stand with rotating bracket, boom with by-pass rollers, spacing and lifting hydrocylinders with rods and flexible tie mechanism. In order to improve labor productivity by improving maneuverability and to increase the maintenance zone, the lifter is equipped with a hydrocylinder of advance and a cross piece which is installed with the possibility of forward and rotational movement on the stand, and in which by means of the hydrocylinder of advance a boom is attached. Within the indicated boom there is a branch of the flexible tie mechanism with end attached with the possibility of regulation over the length on a rotating bracket, while the rod of the lifting hydrocylinder is connected to the cross piece.

Testing lifting systems in nuclear facilities

International Nuclear Information System (INIS)

Kling, H.; Laug, R.

1984-01-01

Lifting systems in nuclear facilities must be inspected at regular intervals after having undergone their first acceptance test. These inspections are frequently carried out by service firms which not only employ the skilled personnel required for such jobs but also make available the necessary test equipment. The inspections in particular include a number of sophisticated load tests for which test load systems have been developed to allow lifting systems to be tested so that reactor specific boundary conditions are taken into account. In view of the large number of facilities to be inspected, the test load system is a modular system. (orig.) [de

Cooperative control system of the floating cranes for the dual lifting

Directory of Open Access Journals (Sweden)

Mihee Nam

2018-01-01

Full Text Available This paper proposes a dual lifting and its cooperative control system with two different kinds of floating cranes. The Mega-erection and Giga-erection in the ship building are used to handle heavier and wider blocks and modules as ships and off-shore platforms are enlarged. However, there is no equipment to handle such Tera-blocks. In order to overcome the limit on performance of existing floating cranes, the dual lifting is proposed in this research. In the dual lifting, two floating cranes are well-coordinated to add up the lift capabilities of both cranes without any loss such that virtually a single crane is lifting, maneuvering and unloading. Two main constraints for the dual lifting are as follows: First, two barges of floating cranes should be constrained as a rigid body not to cause a relative motion between two barges and main hooks of the two cranes should be controlled as main hooks of a single crane. In order words, it is necessary to develop the cooperative control of two floating cranes in order to sustain a center of gravity of the module and minimize the tilting angle during the lifting and unloading by the two floating cranes. Two floating cranes are handled as a master-slave system. The master crane is able to gather information about all working conditions and make a decision to control the individual hook speed, which communicates the slave crane by TCP/IP. The developed control system has been embedded in the real floating crane systems and the dual lifting has been demonstrated five times at SHI shipyard in 2015. The moving angles of the lifting module are analyzed and verified to be suitable for hoisting control. It is verified that the dual lifting can be applied for many heavier and wider blocks and modules to shorten the construction time of ships and off-shore platforms.

Nuclear power experience

International Nuclear Information System (INIS)

1983-01-01

The International Conference on Nuclear Power Experience, organized by the International Atomic Energy Agency, was held at the Hofburg Conference Center, Vienna, Austria, from 13 to 17 September 1982. Almost 1200 participants and observers from 63 countries and 20 organizations attended the conference. The 239 papers presented were grouped under the following seven main topics: planning and development of nuclear power programmes; technical and economic experience of nuclear power production; the nuclear fuel cycle; nuclear safety experience; advanced systems; international safeguards; international co-operation. The proceedings are published in six volumes. The sixth volume contains a complete Contents of Volume 1 to 5, a List of Participants, Authors and Transliteration Indexes, a Subject Index and an Index of Papers by Number

Modeling of load lifting process with unknown center of gravity position

Science.gov (United States)

Kamanin, Y. N.; Zhukov, M. I.; Panichkin, A. V.; Redelin, R. A.

2018-03-01

The article proposes a new type of lifting beams that allows one to lift loads where the position of the center of gravity is unknown beforehand. The benefit of implementing this type of traverse is confirmed by the high demand for this product from the industrial enterprises and lack of their availability on the market. In conducted studies, the main kinematic and dynamic dependencies of the load lifting process with an unknown position of the center of gravity were described allowing for design and verification calculations of the traverse with flexible slings and an adjustable bail to be carried out. The obtained results can be useful to engineers and employees of enterprises engaged in the design and manufacturing of the lifting equipment and scientists doing research in “Carrying and lifting machines”.

Characterization of Oscillatory Lift in MFC Airfoils

OpenAIRE

Lang Jr, Joseph Reagle

2014-01-01

The purpose of this research is to characterize the response of an airfoil with an oscillatory morphing, Macro-fiber composite (MFC) trailing edge. Correlation of the airfoil lift with the oscillatory input is presented. Modal analysis of the test airfoil and apparatus is used to determine the frequency response function. The effects of static MFC inputs on the FRF are presented and compared to the unactuated airfoil. The transfer function is then used to determine the lift component du...

Bioenergy '97: Nordic Bioenergy Conference, market, environment and technology

International Nuclear Information System (INIS)

1997-01-01

(Leading abstract). The conference ''Bioenergy '97: Nordic Bioenergy Conference, market, environment and technology'' took place in Oslo, Norway, 7-8 Oct 1997. The conference papers are grouped under three headings: (1) The nordic energy market. 12 papers. (2) Production and sale of biofuels. 8 papers. (3) Conversion and utilization of biofuels. With subsections New technologies, 4 papers, and Power/heat production from biofuels, 4 papers

Face-Lift Satisfaction Using the FACE-Q.

Science.gov (United States)

Sinno, Sammy; Schwitzer, Jonathan; Anzai, Lavinia; Thorne, Charles H

2015-08-01

Face lifting is one of the most common operative procedures for facial aging and perhaps the procedure most synonymous with plastic surgery in the minds of the lay public, but no verifiable documentation of patient satisfaction exists in the literature. This study is the first to examine face-lift outcomes and patient satisfaction using a validated questionnaire. One hundred five patients undergoing a face lift performed by the senior author (C.H.T.) using a high, extended-superficial musculoaponeurotic system with submental platysma approximation technique were asked to complete anonymously the FACE-Q by e-mail. FACE-Q scores were assessed for each domain (range, 0 to 100), with higher scores indicating greater satisfaction with appearance or superior quality of life. Fifty-three patients completed the FACE-Q (50.5 percent response rate). Patients demonstrated high satisfaction with facial appearance (mean ± SD, 80.7 ± 22.3), and quality of life, including social confidence (90.4 ± 16.6), psychological well-being (92.8 ± 14.3), and early life impact (92.2 ± 16.4). Patients also reported extremely high satisfaction with their decision to undergo face lifting (90.5 ± 15.9). On average, patients felt they appeared 6.9 years younger than their actual age. Patients were most satisfied with the appearance of their nasolabial folds (86.2 ± 18.5), cheeks (86.1 ± 25.4), and lower face/jawline (86.0 ± 20.6), compared with their necks (78.1 ± 25.6) and area under the chin (67.9 ± 32.3). Patients who responded in this study were extremely satisfied with their decision to undergo face lifting and the outcomes and quality of life following the procedure.

Lifted linear phase filter banks and the polyphase-with-advance representation

Energy Technology Data Exchange (ETDEWEB)

Brislawn, C. M. (Christopher M.); Wohlberg, B. E. (Brendt E.)

2004-01-01

A matrix theory is developed for the noncausal polyphase-with-advance representation that underlies the theory of lifted perfect reconstruction filter banks and wavelet transforms as developed by Sweldens and Daubechies. This theory provides the fundamental lifting methodology employed in the ISO/IEC JPEG-2000 still image coding standard, which the authors helped to develop. Lifting structures for polyphase-with-advance filter banks are depicted in Figure 1. In the analysis bank of Figure 1(a), the first lifting step updates x{sub 0} with a filtered version of x{sub 1} and the second step updates x{sub 1} with a filtered version of x{sub 0}; gain factors 1/K and K normalize the lowpass- and highpass-filtered output subbands. Each of these steps is inverted by the corresponding operations in the synthesis bank shown in Figure 1(b). Lifting steps correspond to upper- or lower-triangular matrices, S{sub i}(z), in a cascade-form decomposition of the polyphase analysis matrix, H{sub a}(z). Lifting structures can also be implemented reversibly (i.e., losslessly in fixed-precision arithmetic) by rounding the lifting updates to integer values. Our treatment of the polyphase-with-advance representation develops an extensive matrix algebra framework that goes far beyond the results of. Specifically, we focus on analyzing and implementing linear phase two-channel filter banks via linear phase lifting cascade schemes. Whole-sample symmetric (WS) and half-sample symmetric (HS) linear phase filter banks are characterized completely in terms of the polyphase-with-advance representation. The theory benefits significantly from a number of new group-theoretic structures arising in the polyphase-with-advance matrix algebra from the lifting factorization of linear phase filter banks.

Proceedings IEEE Visualization Conference and IEEE Information Visualization Conference (VIS'07 and INFOVIS'07, Sacramento CA, USA, October 28-November 1, 2007)

NARCIS (Netherlands)

Chen, M.; Hansen, C.; North, C.; Pang, A.; Wijk, van J.J.

2007-01-01

These are the proceedings of the IEEE Visualization Conference 2007 (Vis 2007) and the IEEE Information Visualization Conference 2007 (InfoVis 2007) held during October 28 to November 1, 2007 in Sacramento, California. The power of using computing technology to create useful, effective imagery for

2005 ACGIH Lifting TLV: Employee-Friendly Presentation and Guidance for Professional Judgment

Energy Technology Data Exchange (ETDEWEB)

Splittstoesser, Riley [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); O' Farrell, Daniel Edward [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hill, John [Savannah River Site (SRS), Aiken, SC (United States); McMahon, Terrence [SLAC National Accelerator Lab., Menlo Park, CA (United States); Sastry, Nikhil [SLAC National Accelerator Lab., Menlo Park, CA (United States); Tiemeier, Mark [SLAC National Accelerator Lab., Menlo Park, CA (United States)

2017-05-22

The American Council of Governmental Industrial Hygienists (ACGIH) Lifting Threshold Limit Values (TLVs) provide a tool to reduce incidence of low back and shoulder injuries. However, application of the TLV is too complicated for floor-level workers and relies on professional judgment to assess commonly encountered tasks. This paper presents an Employee-Friendly Simplified Format of the TLV that has been adapted from Table 1 of the Lifting TLV presented in the 2005 TLVs and BEIs Based on the Documentation of the Threshold Limit Values for Chemical Substances and Physical Agents & Biological Exposure Indices. This simplified format can be employed by floor-level workers to self-assess lifting tasks. The Ergonomics Project Team also provides research-based guidance for applying professional judgment consistent with standard industry practice: Extended Work Shifts – Reduce weight by 20% for shifts lasting 8 to 12 hours; Constrained Lower Body Posture – Reduce weight by 25% when lifting in such postures; Infrequently Performed Lifts – Lift up to 15 lbs. ≤3 lifts per hour within the zones marked “No safe limit for repetitive lifting” in the TLVs Table 1; Asymmetry beyond 30° – Reduce weight by 10 lbs. for lifts with up to 60° asymmetry from sagittal plane.

Lift, drag, and guidance forces on alternating polarity magnets, using loop guideways

International Nuclear Information System (INIS)

Lindenbaum, S.D.; Lee, M.S.

1975-01-01

Exact solutions of track current, lift force, and drag force, together with their velocity dependence, have been computed for a vehicle carrying a finite number of fixed current alternating polarity superconducting magnets, suspended at various heights over structured track guideways of the single- and double-loop (''null'') types. Results for the double-loop case are compared with those of a previously reported approximate analysis. The analytical method is then applied to a study of a low-drag guidance loop guideway which is integrable with lift loop guideways utilizing a common set of vehicle magnets. Solutions are obtained for guidance track restoring forces, lateral destabilization forces, and lift force degradation as functions of lateral displacement from symmetry. The dependence of lift, drag, and lift-to-drag on track loop parameters is studied and the linear dependence of lift-to-drag on loop time constant confirmed. The contribution to the forces made by successive addition of alternating polarity magnets is calculated and the marked reduction in lift force pulsation noted

Natural substrate lift-off technique for vertical light-emitting diodes

Science.gov (United States)

Lee, Chia-Yu; Lan, Yu-Pin; Tu, Po-Min; Hsu, Shih-Chieh; Lin, Chien-Chung; Kuo, Hao-Chung; Chi, Gou-Chung; Chang, Chun-Yen

2014-04-01

Hexagonal inverted pyramid (HIP) structures and the natural substrate lift-off (NSLO) technique were demonstrated on a GaN-based vertical light-emitting diode (VLED). The HIP structures were formed at the interface between GaN and the sapphire substrate by molten KOH wet etching. The threading dislocation density (TDD) estimated by transmission electron microscopy (TEM) was reduced to 1 × 108 cm-2. Raman spectroscopy indicated that the compressive strain from the bottom GaN/sapphire was effectively released through the HIP structure. With the adoption of the HIP structure and NSLO, the light output power and yield performance of leakage current could be further improved.

75 FR 27662 - Special Conditions: Boeing 747-468, Installation of a Medical Lift

Science.gov (United States)

2010-05-18

... electrical motors, mounted to the rear wall, between the struts. A lifting gear-drive with shafts and gear... OPERATE LIFT DURING TAXI, TAKEOFF, LANDING, OR TURBULENCE. c. AN APPROVED MEDICAL STRETCHER OR WHEELCHAIR... operation. b. Operate the lift. c. Stow the lift for non-operation such as during TTL and turbulence. d...

Transport of timber by rope-and-pulley lift in steep seams

Energy Technology Data Exchange (ETDEWEB)

Spaniol, J

1980-11-01

This paper describes the rope-and-pulley lift used to transport timber and small items of equipment, which has been installed in tubbing in the return air drop-hole. Gives details of how the lift works and the equipment involved (winch, rope, slings, pulleys, safety and signalling arrangements). Looks at the future prospects of installing these lifts. (In French)

Conference on wind power development in the face of landscape and local project acceptability challenges

International Nuclear Information System (INIS)

Victoire Lejzerzon; Sauron, Claire; Villot, Marie; Ratzbor, Guenter; Tausch, Christian; Cagneaux, Bertrand; Jouneau, Agathe; Stemmer, Boris; Huebner, Gundula; Orozco-Souel, Paola; Lhermitte, Charles; Ferus, Elisabeth; Benezech, Philippe; Gunzelmann, Thomas

2015-01-01

The French-German office for Renewable energies (OFAEnR) organised a conference on n wind power development in the face of landscape and local project acceptability challenges. In the framework of this French-German exchange of experience, participants addressed the following points: the conciliation between landscape protection and wind power development, the definition of landscape environmental quality criteria, the needs and usages of the departments in charge of the treatment of landscape studies in France, the socio-psychological approach of the local acceptability of wind farm projects, the re-powering tool for the improvement of the wind farm integration in the landscape, and the conciliation between the monuments maintenance and wind power development. This document brings together the available presentations (slides) made during this event: 1 - Conciliating landscape protection and wind power development goals in France (Marie Villot); 2 - Wind turbines: Conflicts between development goals, landscape and acceptance - Perception and criteria (Guenter Ratzbor); 3 - Bayern's wind power atlas: a planning tool which takes into account the landscape aspects (Christian Tausch); 4 - Landscape assessment in wind farms projects: what and how to do in French administrative procedures? (Bertrand Cagneaux); 5 - Methods for evaluation of landscape for wind farms projects - A French project developer's feedback (Agathe Jouneau); 6 - Landscape Assessment: Methods from German Landscape Practice (Boris Stemmer); 7 - Acceptance of Wind Turbines - Social Psychological Research (Gundula Huebner); 8 - Local consultation: who to involve, when and how? (Paola Orozco-Souel); 9 - Local acceptability: what dialogue concepts and strategies, and how to manage wind energy objection (Charles Lhermitte); 10 - Re-powering and landscape: chances and limits (Elisabeth Ferus); 11 - Wind power and cultural heritage: consultation and dialogue to succeed (Philippe Benezech); 12

Conference to Focus on Vast Need for 'Village Power'

Science.gov (United States)

site. Conference contact: Barbara Ferris, NREL, 1617 Cole Blvd., Golden, CO 80401. Phone: 303-275-3781 . E-mail Barbara Ferris. NREL is a national laboratory managed by Midwest Research Institute, Battelle

The effect of ac magnetic fields on the lifting power of levitating superconductors

International Nuclear Information System (INIS)

Smolyak, B M; Ermakov, G V; Chubraeva, L I

2007-01-01

This study deals with the decrease in the levitation force under the action of an ac field up to the frequency at which oscillations of the superconducting suspension are limited by inertia. The lifting force was measured as a function of the ac field amplitude and the exposure time. It was shown that the force quickly decreased at the moment the ac field was applied and then continued diminishing, but at a lower rate. A qualitative model was proposed, taking into account two effects of the ac field on the magnetization of the levitating superconductor: a complete destruction of the critical state in some section of the superconductor (to a depth λ ac ) and the initiation of a faster magnetic relaxation in the region where the induction gradient is preserved

Opening Address [International Conference on Human Resource Development for Introducing and Expanding Nuclear Power Programmes, Abu Dhabi (United Arab Emirates), 14-18 March 2010

Energy Technology Data Exchange (ETDEWEB)

Amano, Y [International Atomic Energy Agency, Vienna (Austria)

2012-10-15

Full text: It is a pleasure for me to open this IAEA conference on Human Resource Development for Introducing and Expanding Nuclear Power Programmes. I am very grateful to the Government of the United Arab Emirates for hosting this important event. As you know, the world is witnessing a resurgence of interest in nuclear power. The IAEA has projects on introducing nuclear power with no fewer than 58 of our Member States. We expect between 10 and 25 new countries to bring their first nuclear power plants on line by 2030. These are momentous changes. However, some countries are concerned about a possible shortage of skilled professionals in the nuclear field in the coming decades. The generation of professionals who built and led the nuclear power industry for much of the past 50 years is approaching retirement and in some countries not enough students are coming up through the educational system to take their place. Naturally, we, at the IAEA, want to do all we can to help Member States address this issue. That is why we have organized this conference. The situation is different in each country. For countries with expanding nuclear power programmes, the challenge is to scale up their existing education and training in order to have the required qualified workforce on time. Countries planning to supply nuclear technology to others must not only meet their national human resource needs, but also be able to transfer education and training capacity together with the technology they provide. Finally, countries embarking on nuclear power cannot become too dependent on their technology supplier and need to develop their own home grown expertise and skills base. The IAEA would be happy to help interested States to formulate country specific policies on human resource development, education, training and knowledge management in support of nuclear power programmes. We could also help countries make better use of training facilities, research reactors and other educational

Proceedings of the 5th nuclear science and technology conference

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-11-01

The 5th conference on nuclear science and technology was held on 21-23 November, 1992 in Bangkok. This conference contain papers on non-power applications of nuclear technology in medicine, agriculture and industry. These application including irradiation of food for desinfestation; tram technologies used in diagnosis and therapy and radiation chemistry important to industrial processes. Some technologies which evolved from the development of the nuclear power industry are also discussed.

Proceedings of the 5th nuclear science and technology conference

International Nuclear Information System (INIS)

1994-11-01

The 5th conference on nuclear science and technology was held on 21-23 November, 1992 in Bangkok. This conference contain papers on non-power applications of nuclear technology in medicine, agriculture and industry. These application including irradiation of food for desinfestation; tram technologies used in diagnosis and therapy and radiation chemistry important to industrial processes. Some technologies which evolved from the development of the nuclear power industry are also discussed

Proceedings of the 6th nuclear science and technology conference

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-01

The 6th conference on nuclear science and technology was held on 2 - 4 December, 1996 in Bangkok. This conference contain papers on non-power applications of nuclear technology in medicine, agriculture and industry. These application include irradiation of food for des infestation; tram technologies used in diagnosis and therapy and radiation chemistry important to industrial processes. Some technologies which evolved from the development of nuclear power industry are also discussed

Proceedings of the 11. annual North American natural gas and electricity market conference and trade show : GasFair power 2002. CD-Rom ed.

International Nuclear Information System (INIS)

2002-01-01

The electricity market is undergoing changes, from deregulation to competition and convergence. This conference provided an opportunity for North American natural gas and electricity industries representatives and stake holders to share their views concerning the many challenges, issues and opportunities in this field. Emerging market developments, issues and strategies are some of the topics discussed during this conference and trade show. The organizers placed emphasis on energy purchasers and managers, and the opportunities facing them for the improvement of their company's financial health by means of savings on natural gas costs and electricity purchases. In addition, there are several opportunities for improved energy efficiency and technologies and integrated energy and risk management programs which were all discussed. The economic challenges and opportunities arising from the supply, demand, marketing and pricing for gas and power products and services facing energy marketers, traders, producers, utilities and transporters were addressed. A detailed and practical examination of ways by which energy consumers can address issues of volatile gas and power prices was provided. Effective, cost saving purchasing options and risk management strategies and tools, contracting, outsourcing, aggregating and cost-effective energy management programs were also explored. In all, approximately 900 delegates attended the conference and trade show from all across Canada and the United States. refs., tabs., figs

Proceedings of the sixth international and forty third national conference on fluid mechanics and fluid power: book of abstracts

International Nuclear Information System (INIS)

Jain, Anuj; Paul, Akshoy Ranjan

2016-01-01

Fluid Mechanics and Fluid Power (FMFP) Conference is an important meeting to promote all activities in the field of Fluid Mechanics and Fluid Power in India. FMFP-2016 offers great opportunity to scientists, researchers, engineers and business executives from all parts of the world to share the recent advancements and future trends in all aspects of fluid mechanics and fluid power- be it theoretical, experimental, applied and computational, and build network. It covers theoretical and experimental fluid dynamics, flow instability, transition, turbulence and control, fluid machinery, turbomachinery and fluid power, IC engines and gas turbines, multiphase flows, fluid-structure interaction and flow-induced noise, micro and nano fluid mechanics, bio-inspired fluid mechanics, energy and environment, specialized topics (transport phenomena in materials processing and manufacturing, MHD and EHD flows, granular flows, nuclear reactor, thermal hydraulics, defence and space engineering, sustainable habitat. Papers relevant to INIS are indexed separately

Abrasion behavior of graphite pebble in lifting pipe of pebble-bed HTR

Energy Technology Data Exchange (ETDEWEB)

Shen, Ke; Su, Jiageng [Institute of Nuclear and New Energy Technology, Advanced Nuclear Energy Technology Cooperation Innovation Center, The Key Laboratory of Advanced Nuclear Engineering and Safety, Ministry of Education, Beijing 10084 (China); Zhou, Hongbo [Institute of Nuclear and New Energy Technology, Advanced Nuclear Energy Technology Cooperation Innovation Center, The Key Laboratory of Advanced Nuclear Engineering and Safety, Ministry of Education, Beijing 10084 (China); Chinergy Co., LTD., Beijing 100193 (China); Peng, Wei; Liu, Bing [Institute of Nuclear and New Energy Technology, Advanced Nuclear Energy Technology Cooperation Innovation Center, The Key Laboratory of Advanced Nuclear Engineering and Safety, Ministry of Education, Beijing 10084 (China); Yu, Suyun, E-mail: suyuan@tsinghua.edu.cn [Center for Combustion Energy, The Key Laboratory for Thermal Science and Power Engineering, Ministry of Educations, Tsinghua University, Beijing 10084 (China)

2015-11-15

Highlights: • Quantitative determination of abrasion rate of graphite pebbles in different lifting velocities. • Abrasion behavior of graphite pebble in helium, air and nitrogen. • In helium, intensive collisions caused by oscillatory motion result in more graphite dust production. - Abstract: A pebble-bed high-temperature gas-cooled reactor (pebble-bed HTR) uses a helium coolant, graphite core structure, and spherical fuel elements. The pebble-bed design enables on-line refueling, avoiding refueling shutdowns. During circulation process, the pebbles are lifted pneumatically via a stainless steel lifting pipe and reinserted into the reactor. Inevitably, the movement of the fuel elements as they recirculate in the reactor produces graphite dust. Mechanical wear is the primary source of graphite dust production. Specifically, the sources are mechanisms of pebble–pebble contact, pebble–wall (structural graphite) contact, and fuel handling (pebble–metal abrasion). The key contribution to graphite dust production is from the fuel handling system, particularly from the lifting pipe. During pneumatic lift, graphite pebbles undergo multiple collisions with the stainless steel lifting pipe, thereby causing abrasion of the graphite pebbles and producing graphite dust. The present work explored the abrasion behavior of graphite pebble in the lifting pipe by measuring the abrasion rate at different lifting velocities. The abrasion rate of the graphite pebble in helium was found much higher than those in air and nitrogen. This gas environment effect could be explained by either tribology behavior or dynamic behavior. Friction testing excluded the possibility of tribology reason. The dynamic behavior of the graphite pebble was captured by analysis of the audio waveforms during pneumatic lift. The analysis results revealed unique dynamic behavior of the graphite pebble in helium. Oscillation and consequently intensive collisions occur during pneumatic lift, causing

Creating drag and lift curves from soccer trajectories

Science.gov (United States)

Goff, John Eric; Kelley, John; Hobson, Chad M.; Seo, Kazuya; Asai, Takeshi; Choppin, S. B.

2017-07-01

Trajectory analysis is an alternative to using wind tunnels to measure a soccer ball’s aerodynamic properties. It has advantages over wind tunnel testing such as being more representative of game play. However, previous work has not presented a method that produces complete, speed-dependent drag and lift coefficients. Four high-speed cameras in stereo-calibrated pairs were used to measure the spatial co-ordinates for 29 separate soccer trajectories. Those trajectories span a range of launch speeds from 9.3 to 29.9 m s-1. That range encompasses low-speed laminar flow of air over a soccer ball, through the drag crises where air flow is both laminar and turbulent, and up to high-speed turbulent air flow. Results from trajectory analysis were combined to give speed-dependent drag and lift coefficient curves for the entire range of speeds found in the 29 trajectories. The average root mean square error between the measured and modelled trajectory was 0.028 m horizontally and 0.034 m vertically. The drag and lift crises can be observed in the plots of drag and lift coefficients respectively.

Assessment of the second conference

Energy Technology Data Exchange (ETDEWEB)

Eklund, S A [International Atomic Energy Agency, Vienna (Austria)

1964-08-15

Full text: (Sigvard A. Eklund, Conference Secretary General of the Second Conference, 1958). The Geneva Conference of 1958 was up to then the world's biggest and most comprehensive conference concerned with science and technology. Its description - the peaceful uses of atomic energy - was somewhat deceptive, since the conference covered not only engineering applications and energy problems but the nuclear sciences as a whole. It promoted specialized information, but at the same time attempted to counteract the tendency for overspecialization by attracting scientists and technicians from all the various disciplines which have contributed to the development of atomic energy. Such a big international meeting held under the auspices of the United Nations was effective in a manner different to that of smaller meetings in that it stimulated Governments to release and review material which otherwise might have remained undigested or buried in sometimes inaccessible reports and documents. The timing of the conference was propitious. The advanced countries had successfully operated research reactors long enough to enable the less advanced nations to be provided with much needed information; radioisotopes had become available on a relatively large scale and at lower prices. Consequently research, which had previously been restricted to a small number of privileged institutions, could be carried out anywhere; industry could freely benefit from the same tools; and - perhaps most important from the human aspect - methods could be introduced in medicine which offered new possibilities. In theoretical physics a whole series of newly discovered particles with intriguing properties stimulated the imagination of physicists. After an experimental and testing period the first power reactors were going into operation. Data and experience on fuel and on constructional problems had become available which justified a technical evaluation of the situation. Following the 1955 conference

Assessment of the second conference

International Nuclear Information System (INIS)

Eklund, S.A.

1964-01-01

Full text: (Sigvard A. Eklund, Conference Secretary General of the Second Conference, 1958). The Geneva Conference of 1958 was up to then the world's biggest and most comprehensive conference concerned with science and technology. Its description - the peaceful uses of atomic energy - was somewhat deceptive, since the conference covered not only engineering applications and energy problems but the nuclear sciences as a whole. It promoted specialized information, but at the same time attempted to counteract the tendency for overspecialization by attracting scientists and technicians from all the various disciplines which have contributed to the development of atomic energy. Such a big international meeting held under the auspices of the United Nations was effective in a manner different to that of smaller meetings in that it stimulated Governments to release and review material which otherwise might have remained undigested or buried in sometimes inaccessible reports and documents. The timing of the conference was propitious. The advanced countries had successfully operated research reactors long enough to enable the less advanced nations to be provided with much needed information; radioisotopes had become available on a relatively large scale and at lower prices. Consequently research, which had previously been restricted to a small number of privileged institutions, could be carried out anywhere; industry could freely benefit from the same tools; and - perhaps most important from the human aspect - methods could be introduced in medicine which offered new possibilities. In theoretical physics a whole series of newly discovered particles with intriguing properties stimulated the imagination of physicists. After an experimental and testing period the first power reactors were going into operation. Data and experience on fuel and on constructional problems had become available which justified a technical evaluation of the situation. Following the 1955 conference

Modeling and Design of Hybrid PEM Fuel Cell Systems for Lift Trucks

DEFF Research Database (Denmark)

Hosseinzadeh, Elham

driven lift trucks are being used more and more in different companies to reduce their emissions. However, battery driven lift trucks need a long time to recharge and thus may be out of work for a long time. Fuel cell driven lift trucks diminish this problem and are therefore getting more attention...... in a fork-lift truck. In order for the ejector to operate in the largest possible range of load, different approaches (with fixed nozzle and variable nozzle ejectors) have been investigated. Different geometries have been studied in order to optimize the ejector. The optimization is carried out not only...... a virtual fork-lift system. This investigation examines important performance metrics, such as hydrogen consumption and battery SOC as a function of the fuel cell and battery size, control strategy, drive cycle, and load variation for a fork-lift truck system. This study can be used as a benchmark...

Leading-edge vortex lifts swifts.

Science.gov (United States)

Videler, J J; Stamhuis, E J; Povel, G D E

2004-12-10

The current understanding of how birds fly must be revised, because birds use their hand-wings in an unconventional way to generate lift and drag. Physical models of a common swift wing in gliding posture with a 60 degrees sweep of the sharp hand-wing leading edge were tested in a water tunnel. Interactions with the flow were measured quantitatively with digital particle image velocimetry at Reynolds numbers realistic for the gliding flight of a swift between 3750 and 37,500. The results show that gliding swifts can generate stable leading-edge vortices at small (5 degrees to 10 degrees) angles of attack. We suggest that the flow around the arm-wings of most birds can remain conventionally attached, whereas the swept-back hand-wings generate lift with leading-edge vortices.

Occupational lifting, fetal death and preterm birth

DEFF Research Database (Denmark)

Mocevic, Emina; Svendsen, Susanne Wulff; Jørgensen, Kristian Tore

2014-01-01

OBJECTIVE: We examined the association between occupational lifting during pregnancy and risk of fetal death and preterm birth using a job exposure matrix (JEM). METHODS: For 68,086 occupationally active women in the Danish National Birth Cohort, interview information on occupational lifting...... the JEM. We used Cox regression models with gestational age as underlying time variable and adjustment for covariates. RESULTS: We observed 2,717 fetal deaths and 3,128 preterm births within the study cohort. No exposure-response relation was observed for fetal death, but for women with a prior fetal...... death, we found a hazard ratio (HR) of 2.87 (95% CI 1.37, 6.01) for stillbirth (fetal death ≥22 completed gestational weeks) among those who lifted >200 kg/day. For preterm birth, we found an exposure-response relation for primigravid women, reaching a HR of 1.43 (95% CI 1.13, 1.80) for total loads >200...

Group Lifting Structures For Multirate Filter Banks, II: Linear Phase Filter Banks

Energy Technology Data Exchange (ETDEWEB)

Brislawn, Christopher M [Los Alamos National Laboratory

2008-01-01

The theory of group lifting structures is applied to linear phase lifting factorizations for the two nontrivial classes of two-channel linear phase perfect reconstruction filter banks, the whole-and half-sample symmetric classes. Group lifting structures defined for the reversible and irreversible classes of whole-and half-sample symmetric filter banks are shown to satisfy the hypotheses of the uniqueness theorem for group lifting structures. It follows that linear phase lifting factorizations of whole-and half-sample symmetric filter banks are therefore independent of the factorization methods used to compute them. These results cover the specification of user-defined whole-sample symmetric filter banks in Part 2 of the ISO JPEG 2000 standard.

Does team lifting increase the variability in peak lumbar compression in ironworkers?

NARCIS (Netherlands)

Faber, Gert; Visser, Steven; van der Molen, Henk F.; Kuijer, P. Paul F. M.; Hoozemans, Marco J. M.; van Dieën, Jaap H.; Frings-Dresen, Monique H. W.

2012-01-01

Ironworkers frequently perform heavy lifting tasks in teams of two or four workers. Team lifting could potentially lead to a higher variation in peak lumbar compression forces than lifts performed by one worker, resulting in higher maximal peak lumbar compression forces. This study compared

Development of Advanced High Lift Leading Edge Technology for Laminar Flow Wings

Science.gov (United States)

Bright, Michelle M.; Korntheuer, Andrea; Komadina, Steve; Lin, John C.

2013-01-01

This paper describes the Advanced High Lift Leading Edge (AHLLE) task performed by Northrop Grumman Systems Corporation, Aerospace Systems (NGAS) for the NASA Subsonic Fixed Wing project in an effort to develop enabling high-lift technology for laminar flow wings. Based on a known laminar cruise airfoil that incorporated an NGAS-developed integrated slot design, this effort involved using Computational Fluid Dynamics (CFD) analysis and quality function deployment (QFD) analysis on several leading edge concepts, and subsequently down-selected to two blown leading-edge concepts for testing. A 7-foot-span AHLLE airfoil model was designed and fabricated at NGAS and then tested at the NGAS 7 x 10 Low Speed Wind Tunnel in Hawthorne, CA. The model configurations tested included: baseline, deflected trailing edge, blown deflected trailing edge, blown leading edge, morphed leading edge, and blown/morphed leading edge. A successful demonstration of high lift leading edge technology was achieved, and the target goals for improved lift were exceeded by 30% with a maximum section lift coefficient (Cl) of 5.2. Maximum incremental section lift coefficients ( Cl) of 3.5 and 3.1 were achieved for a blown drooped (morphed) leading edge concept and a non-drooped leading edge blowing concept, respectively. The most effective AHLLE design yielded an estimated 94% lift improvement over the conventional high lift Krueger flap configurations while providing laminar flow capability on the cruise configuration.

CH-53K Heavy Lift Replacement Helicopter (CH-53K)

Science.gov (United States)

2015-12-01

Selected Acquisition Report (SAR) RCS: DD-A&T(Q&A)823-390 CH-53K Heavy Lift Replacement Helicopter (CH-53K) As of FY 2017 President’s Budget...December 2015 SAR March 4, 2016 10:04:18 UNCLASSIFIED 4 Col Henry Vanderborght PMA-261 Heavy Lift Helicopters Program Executive Office - Air, Anti...757-5780 Fax: 301-757-5109 DSN Phone: 757-5780 DSN Fax: 757-5109 Date Assigned: May 29, 2014 Program Information Program Name CH-53K Heavy Lift

Managing cultural diversity in healthcare partnerships: the case of LIFT.

Science.gov (United States)

Mannion, Russell; Brown, Sally; Beck, Matthias; Lunt, Neil

2011-01-01

The National Health Service (NHS) Local Improvement Finance Trust (LIFT) programme was launched in 2001 as an innovative public-private partnership to address the historical under-investment in local primary care facilities in England. The organisations from the public and private sector that comprise a local LIFT partnership each have their own distinctive norms of behaviour and acceptable working practices - ultimately different organisational cultures. The purpose of this article is to assess the role of organisational culture in facilitating (or impeding) LIFT partnerships and to contribute to an understanding of how cultural diversity in public-private partnerships is managed at the local level. The approach taken was qualitative case studies, with data gathering comprising interviews and a review of background documentation in three LIFT companies purposefully sampled to represent a range of background factors. Elite interviews were also conducted with senior policy makers responsible for implementing LIFT policy at the national level. Interpreting the data against a conceptual framework designed to assess approaches to managing strategic alliances, the authors identified a number of key differences in the values, working practices and cultures in public and private organisations that influenced the quality of joint working. On the whole, however, partners in the three LIFT companies appeared to be working well together, with neither side dominating the development of strategy. Differences in culture were being managed and accommodated as partnerships matured. As LIFT develops and becomes the primary source of investment for managing, developing and channelling funding into regenerating the primary care infrastructure, further longitudinal work might examine how ongoing partnerships are working, and how changes in the cultures of public and private partners impact upon wider relationships within local health economies and shape the delivery of patient care

Summary of IEA PVPS international conference 2003

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

This report for the International Energy Agency (IEA) summarises the two-day international conference held on Photovoltaic Power Systems (PVPS) by the IEA in 2003 in Osaka, Japan. The aim of this fourth Executive Conference was to present the achievements of this important international co-operation programme and to discuss the future needs for creating sustainable growth and expanding markets for photovoltaic power systems. The conference was attended by 258 participants. During the conference, the future visions for photovoltaics from both country and industry perspectives were presented and discussed. National issues and needs with respect to grid-connected and stand-alone PV systems were discussed. International issues and future visions were examined. Asian countries presented their current status and experience with the market introduction of photovoltaics. Photovoltaics and its opportunities within the framework of international institutions, namely the IEA, the International Finance Corporation (IFC) and the Clean Development Mechanism (CDM) were addressed, as were the needs of the most important markets - namely for distributed grid-connected applications and rural electrification in developing countries. A round-table discussion was also held on the future role and missions of the PVPS programme.

Cleft-lift operation for pilonidal sinuses under tumescent local anesthesia

DEFF Research Database (Denmark)

Bertelsen, Claus Anders

2011-01-01

The use of tumescent local anesthesia in the Bascom cleft-lift procedure has not been described before.......The use of tumescent local anesthesia in the Bascom cleft-lift procedure has not been described before....

Laser-induced forward transfer (LIFT) of congruent voxels

Energy Technology Data Exchange (ETDEWEB)

Piqué, Alberto, E-mail: pique@nrl.navy.mil [Materials Science and Technology Division, Code 6364, Naval Research Laboratory, Washington, DC 20375 (United States); Kim, Heungsoo; Auyeung, Raymond C.Y.; Beniam, Iyoel [Materials Science and Technology Division, Code 6364, Naval Research Laboratory, Washington, DC 20375 (United States); Breckenfeld, Eric [National Research Council Fellow at the Naval Research Laboratory, Washington, DC 20375 (United States)

2016-06-30

Highlights: • Laser-induced forward transfer (LIFT) is demonstrated with high viscosity Ag nanopaste. • Under the right conditions (viscosity and fluence) the transfer of congruent voxels was achieved. • For viscosities under 100 Pa s, congruent voxel transfer of silver nano-suspensions is only possible under a very narrow range of conditions. • For viscosities over 100 Pa s, congruent voxel transfer of silver nano-pastes works over a wider range of fluences, donor substrate thickness, gap distances and voxel areas. • The laser transfer of congruent voxels can be used for printing electronic patterns in particular interconnects. - Abstract: Laser-induced forward transfer (LIFT) of functional materials offers unique advantages and capabilities for the rapid prototyping of electronic, optical and sensor elements. The use of LIFT for printing high viscosity metallic nano-inks and nano-pastes can be optimized for the transfer of voxels congruent with the shape of the laser pulse, forming thin film-like structures non-lithographically. These processes are capable of printing patterns with excellent lateral resolution and thickness uniformity typically found in 3-dimensional stacked assemblies, MEMS-like structures and free-standing interconnects. However, in order to achieve congruent voxel transfer with LIFT, the particle size and viscosity of the ink or paste suspensions must be adjusted to minimize variations due to wetting and drying effects. When LIFT is carried out with high-viscosity nano-suspensions, the printed voxel size and shape become controllable parameters, allowing the printing of thin-film like structures whose shape is determined by the spatial distribution of the laser pulse. The result is a new level of parallelization beyond current serial direct-write processes whereby the geometry of each printed voxel can be optimized according to the pattern design. This work shows how LIFT of congruent voxels can be applied to the fabrication of 2D

Laser-induced forward transfer (LIFT) of congruent voxels

International Nuclear Information System (INIS)

Piqué, Alberto; Kim, Heungsoo; Auyeung, Raymond C.Y.; Beniam, Iyoel; Breckenfeld, Eric

2016-01-01

Highlights: • Laser-induced forward transfer (LIFT) is demonstrated with high viscosity Ag nanopaste. • Under the right conditions (viscosity and fluence) the transfer of congruent voxels was achieved. • For viscosities under 100 Pa s, congruent voxel transfer of silver nano-suspensions is only possible under a very narrow range of conditions. • For viscosities over 100 Pa s, congruent voxel transfer of silver nano-pastes works over a wider range of fluences, donor substrate thickness, gap distances and voxel areas. • The laser transfer of congruent voxels can be used for printing electronic patterns in particular interconnects. - Abstract: Laser-induced forward transfer (LIFT) of functional materials offers unique advantages and capabilities for the rapid prototyping of electronic, optical and sensor elements. The use of LIFT for printing high viscosity metallic nano-inks and nano-pastes can be optimized for the transfer of voxels congruent with the shape of the laser pulse, forming thin film-like structures non-lithographically. These processes are capable of printing patterns with excellent lateral resolution and thickness uniformity typically found in 3-dimensional stacked assemblies, MEMS-like structures and free-standing interconnects. However, in order to achieve congruent voxel transfer with LIFT, the particle size and viscosity of the ink or paste suspensions must be adjusted to minimize variations due to wetting and drying effects. When LIFT is carried out with high-viscosity nano-suspensions, the printed voxel size and shape become controllable parameters, allowing the printing of thin-film like structures whose shape is determined by the spatial distribution of the laser pulse. The result is a new level of parallelization beyond current serial direct-write processes whereby the geometry of each printed voxel can be optimized according to the pattern design. This work shows how LIFT of congruent voxels can be applied to the fabrication of 2D

Analysis of the Effects of Streamwise Lift Distribution on Sonic Boom Signature

Science.gov (United States)

Yoo, Paul

2013-01-01

Investigation of sonic boom has been one of the major areas of study in aeronautics due to the benefits a low-boom aircraft has in both civilian and military applications. This work conducts a numerical analysis of the effects of streamwise lift distribution on the shock coalescence characteristics. A simple wing-canard-stabilator body model is used in the numerical simulation. The streamwise lift distribution is varied by fixing the canard at a deflection angle while trimming the aircraft with the wing and the stabilator at the desired lift coefficient. The lift and the pitching moment coefficients are computed using the Missile DATCOM v. 707. The flow field around the wing-canard- stabilator body model is resolved using the OVERFLOW-2 flow solver. Overset/ chimera grid topology is used to simplify the grid generation of various configurations representing different streamwise lift distributions. The numerical simulations are performed without viscosity unless it is required for numerical stability. All configurations are simulated at Mach 1.4, angle-of-attack of 1.50, lift coefficient of 0.05, and pitching moment coefficient of approximately 0. Four streamwise lift distribution configurations were tested.

A Quasi-Steady Lifting Line Theory for Insect-Like Hovering Flight.

Directory of Open Access Journals (Sweden)

Mostafa R A Nabawy

Full Text Available A novel lifting line formulation is presented for the quasi-steady aerodynamic evaluation of insect-like wings in hovering flight. The approach allows accurate estimation of aerodynamic forces from geometry and kinematic information alone and provides for the first time quantitative information on the relative contribution of induced and profile drag associated with lift production for insect-like wings in hover. The main adaptation to the existing lifting line theory is the use of an equivalent angle of attack, which enables capture of the steady non-linear aerodynamics at high angles of attack. A simple methodology to include non-ideal induced effects due to wake periodicity and effective actuator disc area within the lifting line theory is included in the model. Low Reynolds number effects as well as the edge velocity correction required to account for different wing planform shapes are incorporated through appropriate modification of the wing section lift curve slope. The model has been successfully validated against measurements from revolving wing experiments and high order computational fluid dynamics simulations. Model predicted mean lift to weight ratio results have an average error of 4% compared to values from computational fluid dynamics for eight different insect cases. Application of an unmodified linear lifting line approach leads on average to a 60% overestimation in the mean lift force required for weight support, with most of the discrepancy due to use of linear aerodynamics. It is shown that on average for the eight insects considered, the induced drag contributes 22% of the total drag based on the mean cycle values and 29% of the total drag based on the mid half-stroke values.