WorldWideScience

Sample records for positioning booster seats

  1. Compatibility of booster seats and vehicles in the U.S. market.

    Science.gov (United States)

    Bing, Julie A; Agnew, Amanda M; Bolte, John H

    2018-05-19

    The objective of this study was to analyze booster and rear vehicle seat dimensions to identify the most frequent compatibility problems. Measurements were collected from 40 high-back and backless boosters and 95 left rear and center rear row seating positions in 50 modern vehicles. Dimensions were compared for 3,800 booster/vehicle seat combinations. For validation and estimation of tolerance and correction factors, 72 booster installations were physically completed and compared with measurement-based compatibility predictions. Dimensions were also compared to the International Organization for Standardization (ISO) volumetric envelopes of forward-facing child restraints and boosters. Seat belt buckles in outboard positions accommodated the width of boosters better than center positions (success rates of 85.4 and 34.7%, respectively). Adequate head restraint clearance occurred in 71.9 to 77.2% of combinations, depending on the booster's head support setting. Booster recline angles aligned properly with vehicle seat cushion angles in 71.5% of combinations. In cases of poor angle alignment, booster angles were more obtuse than the vehicle seat angles 97.7% of the time. Head restraint interference exacerbated angle alignment issues. Data indicate success rates above 90% for boosters being fully supported by the length of the seat cushion and for adequate height clearance with the vehicle roofline. Comparison to ISO envelopes indicates that most boosters on the U.S. market are taller and angled more obtusely than ISO target envelopes. This study quantifies some of the common interferences between boosters and vehicles that may complicate booster usage. Data are useful for design and to prioritize specific problem areas.

  2. Identifying strategies to improve the effectiveness of booster seat laws

    Science.gov (United States)

    2008-05-01

    The objective of this project was to identify strategies to improve the effectiveness of booster seat laws. The project explored the possible factors that relate to the use and nonuse of booster seats, and examined the attitudes of law enforcement of...

  3. Naturalistic driving study of rear seat child occupants: Quantification of head position using a Kinect™ sensor.

    Science.gov (United States)

    Arbogast, Kristy B; Kim, Jinyong; Loeb, Helen; Kuo, Jonny; Koppel, Sjaan; Bohman, Katarina; Charlton, Judith L

    2016-09-01

    Restraint performance is evaluated using anthropomorphic test devices (ATDs) positioned in prescribed, optimal seating positions. Anecdotally, humans-children in particular-assume a variety of positions that may affect restraint performance. Naturalistic driving studies (NDSs), where cameras and other data acquisition systems are placed in a vehicle used by participants during their regular transportation, offer means to collect these data. To date, these studies have used conventional video and analysis methods and, thus, analyses have largely been qualitative. This article describes a recently completed NDS of child occupants in which their position was monitored using a Kinect sensor to quantify their head position throughout normal, everyday driving trips. A study vehicle was instrumented with a data acquisition system to measure vehicle dynamics, a set of video cameras, and a Kinect sensor providing 3D motion capture at 1 Hz of the rear seat occupants. Participant families used the vehicle for all driving trips over 2 weeks. The child occupants' head position was manually identified via custom software from each Kinect color image. The 3D head position was then extracted and its distribution summarized by seat position (left, rear, center) and restraint type (forward-facing child restraint system [FFCRS], booster seat, seat belt). Data from 18 families (37 child occupants) resulted in 582 trips (with children) for analysis. The average age of the child occupants was 45.6 months and 51% were male. Twenty-five child occupants were restrained in FFCRS, 9 in booster seats, and 3 in seat belts. As restraint type moved from more to less restraint (FFCRS to booster seat to seat belt), the range of fore-aft head position increased: 218, 244, and 340 mm on average, respectively. This observation was also true for left-right movement for every seat position. In general, those in the center seat position demonstrated a smaller range of head positions. For the first

  4. Standardized error severity score (ESS) ratings to quantify risk associated with child restraint system (CRS) and booster seat misuse.

    Science.gov (United States)

    Rudin-Brown, Christina M; Kramer, Chelsea; Langerak, Robin; Scipione, Andrea; Kelsey, Shelley

    2017-11-17

    Although numerous research studies have reported high levels of error and misuse of child restraint systems (CRS) and booster seats in experimental and real-world scenarios, conclusions are limited because they provide little information regarding which installation issues pose the highest risk and thus should be targeted for change. Beneficial to legislating bodies and researchers alike would be a standardized, globally relevant assessment of the potential injury risk associated with more common forms of CRS and booster seat misuse, which could be applied with observed error frequency-for example, in car seat clinics or during prototype user testing-to better identify and characterize the installation issues of greatest risk to safety. A group of 8 leading world experts in CRS and injury biomechanics, who were members of an international child safety project, estimated the potential injury severity associated with common forms of CRS and booster seat misuse. These injury risk error severity score (ESS) ratings were compiled and compared to scores from previous research that had used a similar procedure but with fewer respondents. To illustrate their application, and as part of a larger study examining CRS and booster seat labeling requirements, the new standardized ESS ratings were applied to objective installation performance data from 26 adult participants who installed a convertible (rear- vs. forward-facing) CRS and booster seat in a vehicle, and a child test dummy in the CRS and booster seat, using labels that only just met minimal regulatory requirements. The outcome measure, the risk priority number (RPN), represented the composite scores of injury risk and observed installation error frequency. Variability within the sample of ESS ratings in the present study was smaller than that generated in previous studies, indicating better agreement among experts on what constituted injury risk. Application of the new standardized ESS ratings to installation

  5. Emergency department transport rates of children from the scene of motor vehicle collisions: do booster seats make a difference?

    Science.gov (United States)

    House, Darlene R; Huffman, Gretchen; Walthall, Jennifer D H

    2012-11-01

    Motor vehicle collisions (MVCs) are the leading cause of death and disability among children older than 1 year. Many states currently mandate all children between the ages of 4 and 8 years be restrained in booster seats. The implementation of a booster-seat law is generally thought to decrease the occurrence of injury to children. We hypothesized that appropriate restraint with booster seats would also cause a decrease in emergency department (ED) visits compared with children who were unrestrained. This is an important measure as ED visits are a surrogate marker for injury. The main purpose of this study was to look at the rate of ED visits between children in booster seats compared with those in other or no restraint systems involved in MVCs. Injury severity was compared across restraint types as a secondary outcome of booster-seat use after the implementation of a state law. A prospective observational study was performed including all children 4 to 8 years old involved in MVCs to which emergency medical services was dispatched. Ambulance services used a novel on-scene computer charting system for all MVC-related encounters to collect age, sex, child-restraint system, Glasgow Coma Scale score, injuries, and final disposition. One hundred fifty-nine children were studied with 58 children (35.6%) in booster seats, 73 children in seatbelts alone (45.2%), and 28 children (19.1%) in no restraint system. 76 children (47.7%), 74 by emergency medical services and 2 by private vehicle, were transported to the ED with no significant difference between restraint use (P = 0.534). Utilization of a restraint system did not significantly impact MVC injury severity. However, of those children who either died (n = 2) or had an on-scene decreased Glasgow Coma Scale score (n = 6), 75% (6/8) were not restrained in a booster seat. The use of booster-seat restraints does not appear to be associated with whether a child will be transported to the ED for trauma evaluation.

  6. An ecological model to factors associated with booster seat use: A population based study.

    Science.gov (United States)

    Shimony Kanat, Sarit; Gofin, Rosa

    2017-11-01

    Belt-positioning booster seat use (BPB) is an effective technology to prevent severe child injury in cases of car crash. However, in many countries, age-appropriate car restraint use for children aged 4-7 years old remains the lowest among all age groups. The aim of this study was to identify the main determinants of BPB use through a comprehensive approach. An ecological model was used to analyze individual, parent-child relationships, and neighborhood characteristics. Parents of children enrolled in the first and second grades completed a self-reported questionnaire (n=745). The data were subjected to multilevel modeling. The first level examined individual and parent-child relationship variables; in addition the second level tested between neighborhood variance. According to parental self- reports, 56.6% of their children had used a BPB on each car trip during the previous month. The results indicated that the determinants positively related to BPB use were individual and parental; namely, the number of children in the family, the parents' car seat belt use, parental knowledge of children's car safety principles, and a highly authoritative parenting style. Children's temperaments and parental supervision were not associated with BPB use. At the neighborhood level, a small difference was found between neighborhoods for BPB users compared to non-users. Copyright © 2017 Elsevier Ltd. All rights reserved.

  7. Advocacy for booster seat legislation in Florida: a lesson in politics and policy formation.

    Science.gov (United States)

    Haring, R Sterling; Frattaroli, Shannon; Schneider, Eric B; Holland, M Becker; Vernick, Jon S

    2015-04-01

    MVCs are a major contributor to child injury and death. Infant restraint seats and child booster seats have been shown to reduce the odds of severe injury or death when used correctly. While all states have mandated the use of these restraint systems, the age at which a child can be legally restrained using an adult seat belt varies from state to state. Efforts to strengthen Florida's weak child restraint laws have failed for more than a decade; in the 2014 legislative session, advocates succeeded in raising the state's age requirement from 3 years to 5  years. While many factors contributed to this year's success, some key elements included efficient communication of supporting data, a strong and broad advocacy network and the leveraging of election year political rivalries. Efforts to further strengthen the law will continue into future legislative sessions. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

  8. Support force measures of midsized men in seated positions.

    Science.gov (United States)

    Bush, Tamara Reid; Hubbard, Robert P

    2007-02-01

    Two areas not well researched in the field of seating mechanics are the distribution of normal and shear forces, and how those forces change with seat position. The availability of these data would be beneficial for the design and development of office, automotive and medical seats. To increase our knowledge in the area of seating mechanics, this study sought to measure the normal and shear loads applied to segmental supports in 12 seated positions, utilizing three inclination angles and four levels of seat back articulation that were associated with automotive driving positions. Force data from six regions, including the thorax, sacral region, buttocks, thighs, feet, and hand support were gathered using multi-axis load cells. The sample contained 23 midsized subjects with an average weight of 76.7 kg and a standard deviation of 4.2 kg, and an average height of 1745 mm with a standard deviation of 19 mm. Results were examined in terms of seat back inclination and in terms of torso articulation for relationships between seat positions and support forces. Using a repeated measures analysis, significant differences (p<0.05) were identified for normal forces relative to all inclination angles except for forces occurring at the hand support. Other significant differences were observed between normal forces behind the buttocks, pelvis, and feet for torso articulations. Significant differences in the shear forces occurred under the buttocks and posterior pelvis during changes in seat back inclination. Significant differences in shear forces were also identified for torso articulations. These data suggest that as seat back inclination or torso articulation change, significant shifts in force distribution occur.

  9. The AGS Booster Beam Position Monitor system

    International Nuclear Information System (INIS)

    Ciardullo, D.J.; Abola, A.; Beadle, E.R.; Smith, G.A.; Thomas, R.; Van Zwienen, W.; Warkentien, R.; Witkover, R.L.

    1991-01-01

    To accelerate both protons and heavy ions, the AGS Booster requires a broadband (multi-octave) beam position monitoring system with a dynamic range spanning several orders of magnitude (2 x 10 10 to 1.5 x 10 13 particles per pulse). System requirements include the ability to acquire single turn trajectory and average orbit information with ± 0.1 mm resolution. The design goal of ± 0.5 mm corrected accuracy requires that the detectors have repeatable linear performance after periodic bakeout at 300 degree C. The system design and capabilities of the Booster Beam Position Monitor will be described, and initial results presented. 7 refs., 5 figs

  10. Boosting restraint norms: a community-delivered campaign to promote booster seat use.

    Science.gov (United States)

    Bryant-Stephens, Tyra; Garcia-Espana, J Felipe; Winston, Flaura K

    2013-01-01

    The objective of this study was to evaluate the effectiveness of a theoretically grounded community-delivered marketing campaign to promote belt-positioning booster seat (BPB) use among vulnerable populations when disseminated by community members. A prospective, nonrandomized community intervention trial was conducted to evaluate the "Boosting Restraint Norms" social marketing campaign delivered by community partners in Norristown, Pennsylvania (intervention community), between October 2008 and November 2008. York, Pennsylvania, served as the comparison community. In total, 800 vehicles with 822 children aged 4 to 7 years were observed for BPB use, the primary outcome of interest, at baseline (September 2008) and at 6 months after intervention (April 2009). During the study period, a 28 percent increase in the prevalence of BPB use at 6 months was observed in the intervention community with no change in the prevalence of BPB use in the comparison community. After adjustment for child age and gender, vehicle type, driver gender, and driver level, BPB use increased from 39 to 50 percent in the intervention community. The "Boosting Restraint Norms" social marketing campaign, distributed through community organizations combined with caregiver education and a one-time free distribution of BPBs, was effective in increasing BPB use. This study demonstrates the feasibility of utilizing community organizations with established audiences to spread the "No Regrets" messaging of the campaign in the community. This study also indicates that spreading evidence-based messages in this manner may effectively change behavior in populations that are often hard to reach. Future studies are needed in which this methodology is tested in additional communities and rural settings.

  11. Misuse of booster cushions - an observation study of children's performance during buckling up.

    Science.gov (United States)

    Osvalder, Anna-Lisa; Bohman, Katarina

    2008-10-01

    Booster cushions are effective tools to protect children from injuries in car crashes, but there remains a large amount of misuse. The aim of this study was to assess potential misuse of booster cushions in an observational laboratory study, and to identify whether booster cushion design, age or clothing had any effect. 130 Swedish children from the ages of 4-12 years participated. Each child buckled up on an integrated and on an aftermarket booster cushion in the rear seat. The older children also buckled up with seat belt only. Interviews, observations and body measurements were performed. Time to buckle up and amount of belt slack were registered. Photographs were taken to document misuse. Results showed that 77% failed to perform correct belt routing on the aftermarket cushion, independent of age, although they were familiar with this system. The misuse rate for the integrated cushion was only 4%. No misuse was found for seat belt only. Few children tightened the belt. The belt slack increased when wearing winter jackets. This indicates the importance of adding pretensioners to the rear seat. Sled tests with HIII&TNO 6y dummies were also performed for the most frequent misuse situations found. The main conclusion is that an integrated booster cushion has many advantages compared to an aftermarket cushion regarding both safety and comfort. It is easy and quick to handle, has few possibilities for misuse, has an intuitive design, the buckling up sequence is equal to buckling up with an ordinary seat belt, and younger children can buckle up correctly.

  12. Injury severity and seating position in accidents with German EMS helicopters.

    Science.gov (United States)

    Hinkelbein, Jochen; Spelten, Oliver; Neuhaus, Christopher; Hinkelbein, Mandy; Özgür, Enver; Wetsch, Wolfgang A

    2013-10-01

    Accident rates and fatality rates for Helicopter Emergency Medical Service (HEMS) missions have been investigated recently, but none of these studies considered the influence of the seating position in the helicopter. The aim of the present descriptive and observational study was to analyze injury severity depending on the seating position during HEMS accidents in Germany. Data from the German Federal Agency for Flight Accident Investigation was gathered for a period of 40 years (from 1970 to 2009). The seating position in the aircraft during the accident and the resulting injury severity (i.e., 1=no; 2=slight; 3=severe; and 4=fatal) were recorded. Injury severity was compared using the Fisher's exact test. P values accidents were investigated (n=61 accidents did not lead to any injuries in the occupants, n=7 accidents resulted in minor, and n=6 in severe injuries, and lethal injuries resulted from n=15 accidents). The occupant in the "patient" position was most likely to suffer from deadly injuries (44.9%), followed by the HEMS crew member rear seat (25.0%), compared to lower lethality rates in the other seating positions (9.4-11.2%). Sitting on the HEMS crew member rear seat also was associated with the highest percentage of severe and minor injuries (12.5% each). In HEMS accidents, the patients' position and the HEMS crew member rear seat were found to be at the highest risk for fatal or severe injuries. These results support the urgent requirement of a large international data base for HEMS accidents as a basis for further studies to improve the safety in HEMS missions. Copyright © 2013 Elsevier Ltd. All rights reserved.

  13. Design of the AGS Booster Beam Position Monitor electronics

    International Nuclear Information System (INIS)

    Ciardullo, D.J.; Smith, G.A.; Beadle, E.R.

    1991-01-01

    The operational requirements of the AGS Booster Beam Position Monitor system necessitate the use of electronics with wide dynamic range and broad instantaneous bandwidth. Bunch synchronization is provided by a remote timing sequencer coupled to the local ring electronics via digital fiber-optic links. The Sequencer and local ring circuitry work together to provide single turn trajectory or average orbit and intensity information, integrated over 1 to 225 bunches. Test capabilities are built in for the purpose of enhancing BPM system accuracy. This paper describes the design of the Booster Beam Position Monitor electronics, and presents performance details of the front end processing, acquisition and timing circuitry

  14. Comparative study of potential whiplash injuries for different occupant seated positions during rear end accidents.

    Science.gov (United States)

    Omerović, Senad; Tomasch, Ernst; Gutsche, Andreas J; Prebil, Ivan

    2016-01-01

    Whiplash injuries to the cervical spine represent a considerable economic burden on society with medical conditions, in some cases persisting for more than a year. Numerous studies of whiplash injuries have been made for occupant normal seated position, leaving the analysis of neck injuries for out-of-normal positions not well documented. For that purpose, a detailed human cervical spine finite element model was developed. The analysis was made for four most common occupant seated positions, such as: Normal Position with the torso against the seat back and the head looking straight ahead, Torso Lean forward position with the torso away from the seat back for approximately 10°, Head Flexed position with the head flexed forward approximately 20° from the normal position and Head-Flexed with Torso Lean forward position with the head flexed forward approximately 20° and torso 10° from the normal position. The comparative study included the analysis of capsular ligament deformation and the level of S-curvature of the cervical spine. The model developed predicted that Head Flexed seated position and Head-Flexed with Torso Lean forward seated position are most threatening for upper and lower cervical spine capsular ligament, respectively. As for the level of S-curvature, the model predicted that Head-Flexed with Torso Lean forward seated position would be most prone to neck injuries associated with it. This study demonstrated that the occupant seated position has a significant influence on potential whiplash injuries.

  15. Ergonomic Evaluation of Space Shuttle Light-Weight Seat Lever Position and Operation

    Science.gov (United States)

    Maida, J.; Rajulu, Sudhakar L.; Bond, Robert L. (Technical Monitor)

    2000-01-01

    During a Shuttle flight in the early part of 1999, one of the crewmembers was unable to operate the backrest lever for the light-weight seat in microgravity. It is essential that the crewmembers are able to adjust this back-rest lever, which is titled forward 2 degrees from vertical during launch and then moved backwards to 10 degrees aft of vertical upon reaching orbit. This adjustment is needed to cushion the crewmembers during an inadvertent crash landing situation. The original Shuttle seats, which had seat controls located on the front left and right sides of the seat, were replaced recently with the new light-weight seats. The controls for these new, seats were moved to the night side with one control at the front and the other at the back. While it was uncertain whether the problem encountered was unique to that crewmember or not it was clear to the personnel responsible for maintaining the Shuttle seats that not knowing the cause of the problem posed a safety concern for NASA. Hence the Anthropometry and Biomechanics Facility (ABF) of the Johnson Space Center was requested to perform an evaluation of the seat controls and provide NASA with appropriate recommendations on whether the seat lever positions and operations should be modified. The ABF designed an experiment to investigate the amount of pull force exerted by subjects, wearing an unpressurized or pressurized crew launch escape suit, when controls were placed in the front and back (on the right side) of the light-weight seat. Single-axis load cells were attached to the seat levers, which measured the maximum static pull forces that were exerted by the subjects. Twelve subjects, six male and six female, participated in this study. Each subject was asked to perform the pull test at least three times for each combination of lever position and suit pressure conditions. The results from this study showed that as a whole (or in general), the subjects were able to pull on the lever at the back position with

  16. Drivers' attitudes toward front or rear child passenger belt use and seat belt reminders at these seating positions.

    Science.gov (United States)

    Kidd, David G; McCartt, Anne T

    2014-01-01

    Passengers, especially those in rear seating positions, use seat belts less frequently than drivers. In-vehicle technology can inform drivers when their passengers are unbuckled and encourage passengers to use belts. The current study collected information about drivers' attitudes toward passenger belt use and belt reminders for front passengers and children in back seats. A national telephone survey of 1218 people 18 and older was conducted, of which 477 respondents were drivers who transport a front seat passenger at least once a week and 254 were drivers who transport an 8- to 15-year-old child in the back seat. Respondents were asked about their attitudes toward belt use by their front passengers or rear child passengers and preferences for different passenger belt reminder features. Ninety percent of drivers who regularly transport front seat passengers said that the passengers always use seat belts. Reported belt use was even higher among 8- to 15-year-old children in the back seat (97%). Among the drivers whose children do not always buckle up, about half said their child unbuckled the belt during the trip. Almost every full-time belt use driver (96%) would encourage front passengers to buckle up if not belted, compared to 57 percent of part-time belt users and nonusers. In contrast, nearly every driver who transports children in the back seat would encourage their belt use, regardless of the driver's belt use habits. Most drivers who transport front passengers wanted passenger belt reminders to encourage passengers to buckle up. Most of these drivers wanted a chime/buzzer or warning light or text display and wanted the reminder to last indefinitely. Most drivers who transport child passengers in the rear seat wanted the vehicle to indicate whether child passengers are unbuckled. A large majority of these drivers wanted notifications via a visual diagram of seating positions and belt use, a chime/buzzer, and a warning light or text display. These drivers

  17. Occupant Kinematics in Simulated Autonomous Driving Vehicle Collisions: Influence of Seating Position, Direction and Angle.

    Science.gov (United States)

    Kitagawa, Yuichi; Hayashi, Shigeki; Yamada, Katsunori; Gotoh, Mitsuaki

    2017-11-01

    This two-part study analyzed occupant kinematics in simulated collisions of future automated driving vehicles in terms of seating configuration. In part one, a frontal collision was simulated with four occupants with the front seats reversed. The left front seat occupant was unbelted while the others were belted. In part two of the study, occupant restraint was examined in various seating configurations using a single seat model with a three-point seatbelt. The seat direction with respect to impact was considered as forward, rearward, and lateral facing in 45 degree increments. The effect of seat recline was also studied in the forward-facing and rear-facing cases by assuming three positions: driving position, resting position and relaxed position. Occupants were represented by human body finite element models. The results of part one showed that the front seat (rear-facing) occupants were restrained by the seatback, resulting in T1 forward displacement less than 100 mm; the rear seat occupants were restrained by the seatbelt resulting larger T1 forward displacement more than 500 mm. The results of the part two showed the directional dependence of occupant restraint. Greater T1 displacements were observed when the occupant faced lateral or front oblique. However, the seatbelt provided some restraint in all directions considered. The seatback generated contact force to the occupant when it was in the impact direction, including the lateral directions. The relaxed position allowed increased excursion compared to the driving position when the occupant faced rearward, but the magnitude of this increase was lower with lower impact speed.

  18. Beam position monitoring in the AGS Linac to Booster transfer line

    International Nuclear Information System (INIS)

    Shea, T.J.; Brodowski, J.; Witkover, R.

    1991-01-01

    A beam position monitor system has been developed and used in the commissioning of Brookhaven's Linac to Booster transfer line. This line transports a chopped, RF modulated H- beam from the 200 MeV Linac to the AGS Booster. Over a 15dB dynamic range in beam current, the position monitor system provides a real-time, normalized position signal with an analog bandwidth of about 20 MHz. Seven directional coupler style pickups are installed in the line with each pickup sensing both horizontal and vertical position. Analog processing electronics are located in the tunnel and incorporate the amplitude modulation to phase modulation normalization technique. To avoid interference from the 200 MHz linac RF system, processing is performed at 400 MHz. This paper provides a system overview and report results from the commissioning experience

  19. Position pickup of the PS Booster

    CERN Multimedia

    CERN PhotoLab

    1975-01-01

    The beam position around the 4 rings of the PS Booster (originally 800 MeV, now 1.4 GeV), is measured with electrostatic pickups (PU). They consist of a ceramic cylinder forming part of the vacuum chamber, and, in order to save space, they are located inside the multipole lenses. The inside of the ceramic is coated with a metallic layer, into which the form of the electrodes was cut by computer-controlled micro-sandblasting. Each PU has a pair of horizontal and a pair of vertical electrodes, as well as a separate intensity-sensing circular electrode.

  20. Car seat inspection among children older than 3 years: Using data to drive practice in child passenger safety.

    Science.gov (United States)

    Kroeker, Amber M; Teddy, Amy J; Macy, Michelle L

    2015-09-01

    Motor vehicle crashes are the leading cause of unintentional death and disability among children 4 years to 12 years of age in the United States. Despite the high risk of injury from motor vehicle crashes in this age group, parental awareness and child passenger safety programs in particular may lack focus on this age group. This is a retrospective cross-sectional analysis of child passenger safety seat checklist forms from two Safe Kids coalitions in Michigan (2013) to identify restraint type upon arrival to car seat inspections. Other variables were included if the coalition provided a new child safety seat and if the child had a sibling who underwent a car seat inspection. χ statistics were used to compare change in restraint use on arrival and at departure, the proportion of children attending a car seat inspection event by age, the age category of children by site, the proportion of children with siblings also undergoing a car seat inspection by age, and the distribution of a new child safety seat by age. Data were available from 1,316 Safe Kids Huron Valley and 3,215 Safe Kids Greater Grand Rapids car seat inspections. Just 10.8% of the total seats inspected were booster seats. Child safety seats for infant and young children were more commonly inspected (rear-facing carrier [40.3%], rear-facing convertible [10.2%], and forward-facing [19.3%] car seats). Few children at inspections used a seat belt only (5.4%) or had no restraint (13.8%). Children 4 years and older were found to be in a suboptimal restraint at least 30% of the time. Low proportions of parents use car seat inspections for children in the booster seat age group. The proportion of children departing the inspection in a more protective restraint increased with increasing age. This highlights an area of weakness in child passenger safety programs and signals an opportunity to strengthen efforts on The Booster Age Child. Epidemiologic/prognostic study, level III.

  1. Automated recognition of rear seat occupants' head position using Kinect™ 3D point cloud.

    Science.gov (United States)

    Loeb, Helen; Kim, Jinyong; Arbogast, Kristy; Kuo, Jonny; Koppel, Sjaan; Cross, Suzanne; Charlton, Judith

    2017-12-01

    Child occupant safety in motor-vehicle crashes is evaluated using Anthropomorphic Test Devices (ATD) seated in optimal positions. However, child occupants often assume suboptimal positions during real-world driving trips. Head impact to the seat back has been identified as one important injury causation scenario for seat belt restrained, head-injured children (Bohman et al., 2011). There is therefore a need to understand the interaction of children with the Child Restraint System to optimize protection. Naturalistic driving studies (NDS) will improve understanding of out-of-position (OOP) trends. To quantify OOP positions, an NDS was conducted. Families used a study vehicle for two weeks during their everyday driving trips. The positions of rear-seated child occupants, representing 22 families, were evaluated. The study vehicle - instrumented with data acquisition systems, including Microsoft Kinect™ V1 - recorded rear seat occupants in 1120 driving 26 trips. Three novel analytical methods were used to analyze data. To assess skeletal tracking accuracy, analysts recorded occurrences where Kinect™ exhibited invalid head recognition among a randomly-selected subset (81 trips). Errors included incorrect target detection (e.g., vehicle headrest) or environmental interference (e.g., sunlight). When head data was present, Kinect™ was correct 41% of the time; two other algorithms - filtering for extreme motion, and background subtraction/head-based depth detection are described in this paper and preliminary results are presented. Accuracy estimates were not possible because of their experimental nature and the difficulty to use a ground truth for this large database. This NDS tested methods to quantify the frequency and magnitude of head positions for rear-seated child occupants utilizing Kinect™ motion-tracking. This study's results informed recent ATD sled tests that replicated observed positions (most common and most extreme), and assessed the validity of child

  2. Towards evidence-based classification in wheelchair sports: impact of seating position on wheelchair acceleration.

    Science.gov (United States)

    Vanlandewijck, Yves C; Verellen, Joeri; Tweedy, Sean

    2011-07-01

    In most Paralympic wheelchair sports, active trunk range of movement is assessed by observing shoulder girdle excursion during active trunk movements and is a key determinant of an athlete's class. However, to date research evaluating the impact of reduced trunk range of movement on wheelchair sports performance has not been conducted. In the present study, 15 non-disabled male participants performed two 20-s sprints on a wheelchair ergometer in each of three seating positions. Positions were typical of those used to enhance sitting stability in wheelchair sport and each impacted available trunk range of movement differently: condition-90 (seated with thighs horizontal; unrestricted range of movement) condition-45 (seated with thighs in 45°), and condition-0 (seated with hips maximally flexed; minimum range of movement). In condition-90, the trunk only actively contributed to the first push; for the remainder of the sprint, the trunk was held almost isometrically at 48.2° to the horizontal (range 42.1-56.4°). Similar patterns were observed for both condition-45 and condition-0. Compared with condition-90, participants in condition-0 had reduced capacity to accelerate of statistical (P sports performance, including strapping, seating position, and impairments of trunk muscle power and coordination.

  3. Enhancement of control rod drive mechanism seating position detector for JRR-3

    International Nuclear Information System (INIS)

    Ohuchi, Satoshi; Kurumada, Osamu; Kamiishi, Eigo; Sato, Masayuki; Ikekame, Yoshinori; Wada, Shigeru

    2016-06-01

    The purpose of the control rod drive mechanism seating position detector for JRR-3 is one of methods for confirming the shutdown condition of the reactor and sending out the seat position signal to other systems. The detector has been utilizing more than 25 years with maintenance regularly. However, some troubles occurred recently. Moreover, the detector has already been discontinued, and it is confirmed that the successor detector is unsuitable for the control rod drive mechanism of JRR-3. Therefore, it was necessary to select the adequate detector to the control rod drive mechanism of JRR-3. Accordingly, we built a test device with the aim of verifying several detectors for integrity and function. At the time of the test for performance confirmation, it was occurred unexpected problems. Nevertheless, we devise improvement of the problems and took measures. Thus we were able to make adequate detector for JRR-3 and replace to enhanced detector. This paper reports the Enhanced of Control rod drive mechanism seating position detector. (author)

  4. Design of the AGS Booster beam position monitor system

    International Nuclear Information System (INIS)

    Beadle, E.; Brennan, J.M.; Ciardullo, D.J.; Savino, J.; Stanziani, V.; Thomas, R.; Van Zwienen, W.; Witkover, R.L.; Schulte, E.

    1989-01-01

    The AGS Booster beam position monitor system must cover a wide range of beam intensity and bunch length for proton and heavy ion acceleration. The detector is designed to maintain 0.1 mm local tolerance following 300 degree C bakeout. The electronics will be located in the tunnel, communicating via fiber optic links to avoid ground loops. The design will be described and test results for prototype units presented. 5 refs., 4 figs

  5. Autonomous booster device of a safety valve

    International Nuclear Information System (INIS)

    Namand, H.

    1983-01-01

    The invention concerns an autonomous booster device of a protection safety valve of a pressure vessel. The valve comprises a hollow structure, a seat connected with a mobile flap forming one piece with a stem and a calibration spring bearing on the stem and on the valve structure to maintain the flap bearing on the seat. The stem of the flap is prolongated in a box forming one piece with the valve structure and receives an added push of a spring. The box acts as a pressure device of which the piston can exercise on the stem a push opposite to and larger than the spring one. The feeding device of the pressure box is finally described in detail [fr

  6. Implementation of electron beam position measurement algorithm and embedded web server using MCS-51 microcontroller for Booster Synchrotron

    International Nuclear Information System (INIS)

    Shrivastava, B.B.; Chouhan, Manish; Puntambekar, T.A.; Tiwari, A.N.

    2015-01-01

    The Booster Synchrotron at RRCAT caters as Injector Machine for Indus-1 and Indus-2 with the repetition rate of 1Hz. In Booster Synchrotron, energy of electron bunches are increased from 20 MeV to 450 MeV (in ∼ 280 ms) and 550 MeV (in ∼ 340 ms ) for Indus-1 and Indus-2 respectively. An algorithm for microcontroller based beam position measurement system has been developed for the Booster Synchrotron to measure the fast changes in the beam position of electron bunches during energy ramping. In this paper, software implementation in microcontroller and its optimization to achieve beam position update rate of 1 kHz is discussed. (author)

  7. Child seat belt guidelines: Examining the 4 feet 9 inches rule as the standard.

    Science.gov (United States)

    Morse, Amber M; Aitken, Mary E; Mullins, Samantha H; Miller, Beverly K; Pomtree, Mindy M; Ulloa, Erin M; Montgomery, Jeffrey S; Saylors, Marie E

    2017-11-01

    Current American Academy of Pediatrics recommendations regarding transition from child safety/booster seat to adult safety belt use indicate that children should be at least 4 feet 9 inches, 8 years old, or 80 pounds. Proper fit in the vehicle seat, assessed with a five-point fit test, should also be met. Although most children reach 4 feet 9 inches around age 8 years, each child and vehicle presents a unique combination; thus a child may not fit appropriately in all vehicle types using only the 4 feet 9 inches requirement. We enrolled children, aged 7 years to 12 years, into our study. Height, weight, and demographic data were obtained. A Child Passenger Safety Technician then performed the five-point fit test in each of a uniform lineup of five vehicles. Data were collected on fit in the standard vehicle seat and also in a booster seat. We set 90% as the threshold proportion of children who meet all criteria for proper fit to validate current recommendations of a height of 4 feet 9 inches. Data were collected on 388 children. The percentage of 90% proper fit was met in the compact car and small sport-utility vehicle (SUV). However, only 80 (77%) of 104 students (p guidelines for an adult seat belt do not meet safety requirements for fit, especially in larger, commonly used vehicles (large SUVs and trucks). This emphasizes the need for evaluation of fit by a trained personnel and/or development of standard back seat dimensions in all vehicles for maximum safety. Epidemiologic level 1.

  8. Child seat belt guidelines: Examining the 4 feet 9 inches rule as the standard.

    Science.gov (United States)

    Morse, Amber M; Aitken, Mary E; Mullins, Samantha H; Miller, Beverly K; Pomtree, Mindy M; Ulloa, Erin M; Montgomery, Jeffrey S; Saylors, Marie E

    2017-08-01

    Current American Academy of Pediatrics recommendations regarding transition from child safety/booster seat to adult safety belt use indicate that children should be at least 4 feet 9 inches, 8 years old, or 80 pounds. Proper fit in the vehicle seat, assessed with a five-point fit test, should also be met. Although most children reach 4 feet 9 inches around age 8 years, each child and vehicle presents a unique combination; thus a child may not fit appropriately in all vehicle types using only the 4 feet 9 inches requirement. We enrolled children, aged 7 years to 12 years, into our study. Height, weight, and demographic data were obtained. A Child Passenger Safety Technician then performed the five-point fit test in each of a uniform lineup of five vehicles. Data were collected on fit in the standard vehicle seat and also in a booster seat. We set 90% as the threshold proportion of children who meet all criteria for proper fit to validate current recommendations of a height of 4 feet 9 inches. Data were collected on 388 children. The percentage of 90% proper fit was met in the compact car and small sport-utility vehicle (SUV). However, only 80 (77%) of 104 students (p vehicles (large SUVs and trucks). This emphasizes the need for evaluation of fit by a trained personnel and/or development of standard back seat dimensions in all vehicles for maximum safety. Epidemiologic study, level III; Therapeutic study, level V.

  9. Take your seats: Leftward asymmetry in classroom seating choice

    Directory of Open Access Journals (Sweden)

    Victoria Lynn Harms

    2015-08-01

    Full Text Available Despite an overall body symmetry, human behaviour is full of examples of asymmetry, from writing or gesturing to kissing and cradling. Prior research has revealed that theatre patrons show a bias towards sitting on the right side of a movie theatre. Two competing theories have attempted to explain this seating asymmetry: one posits that expectation of processing demand drives the bias; the other posits that basic motor asymmetries drive the bias. To test these theories we assessed the real-world classroom seating choices of university students using photographs. A bias for students to choose seats on the left side of the classroom was observed, in contrast to the right side bias observed in theatre seating studies. These results provide evidence in support of a processing-expectation bias.

  10. The Physiologic and Behavioral Implications of Playing Active and Sedentary Video Games in a Seated and Standing Position.

    Science.gov (United States)

    Sanders, Gabriel J; Rebold, Michael; Peacock, Corey A; Williamson, Meagan L; Santo, Antonio S; Barkley, Jacob E

    Previous studies have assessed physiologic response while playing video games per manufacturer instructions with participants standing during active video game play and seated during sedentary game play. It is not known whether an assigned seated or standing position affects positional preference and oxygen consumption (VO2) while gaming. The purpose of the study was to assess VO2 and preference of playing active and sedentary video games in a seated and standing position. VO2 was assessed in 25 participants during four, 20-minute conditions; resting, PlayStation 2 Madden NFL Football 2011, Nintendo Wii-Sports Boxing and Nintendo Wii Madden NFL Football 2011. Each condition was divided into two positional conditions (10 minutes seated, 10 minutes standing) and each participant indicated their positional preference after each 20-minute condition. Standing VO2 (4.4 ± 0.2 ml • kg-1 • min-1 PS2, 4.6 ± 0.1 ml • kg-1 • min-1 Wii Madden, 6.8 ± 0.3 ml • kg-1 • min-1Wii Boxing) was significantly (p ≤ 0.001) greater than seated VO2 (4.0 ± 0.1 ml • kg-1 • min-1 PS2, 4.2 ± 0.1 ml • kg-1 • min-1 Wii Madden, 6.1 ± 0.3 ml • kg-1 • min-1Wii Boxing) for each gaming condition. Participants preferred (p ≤ 0.001) to sit for all gaming conditions except Wii Boxing. Playing video games while standing increases VO2 to a greater extent than playing the same games in a seated position. Standing was only preferred for the most physiologically challenging game, Wii Boxing. Gaming position should be considered when assessing the physiologic and behavioral outcomes of playing video games.

  11. Assessment of a head support system to prevent pediatric out-of-position: an observational study.

    Science.gov (United States)

    Lopez-Valdes, Francisco J; Forman, Jason L; Ash, Joseph H; Kent, Richard; Alba, Juan J; Segui-Gomez, Maria

    Head injuries are the most common severe injuries sustained by pediatric occupants in road traffic crashes. Preventing children from adopting positions that can result in an increased injury risk due to unfavorable interactions with the restraints is fundamental. The objective of this paper was to assess the effect of a head support system (SS) on the lateral position of the head, the vertical position of the sternum and the shoulder belt fit. Thirty pediatric rear-seat passengers were exposed to two 75-minute trials. Volunteers were restrained by a three-point belt and, if needed, used the appropriate child restraint system for their anthropometry (high-back booster, low-back booster, no booster). A case crossover study was designed in which the volunteers used the head support system (SS) during one of the trials, acting as their own controls (No SS) in the other. Compared to the control group, the head support reduced significantly the 90(th) percentile value of the absolute value of the relative lateral motion of the head, regardless of the restraint used. The system also reduced the maximum downward position of the sternal notch within the low-back booster group. As for the belt fit, the use of the head support improved significantly the position of the shoulder belt on the occupant in the low-back booster and in the no booster groups.

  12. Descriptive study of electromagnetic wave distribution for various seating positions: using digital textbooks.

    Science.gov (United States)

    Seomun, GyeongAe; Kim, YoungHwan; Lee, Jung-Ah; Jeong, KwangHoon; Park, Seon-A; Kim, Miran; Noh, Wonjung

    2014-04-01

    To better understand environmental electromagnetic wave exposure during the use of digital textbooks by elementary school students, we measured numeric values of the electromagnetic fields produced by tablet personal computers (TPCs). Specifically, we examined the distribution of the electromagnetic waves for various students' seating positions in an elementary school that uses digital textbooks. Electric and magnetic fields from TPCs were measured using the HI-3603 Visual Display Terminal/ Very Low Frequency (VDT/VLF) radiation measurement system. Electromagnetic field values from TPCs measured at a student's seat and at a teacher's computer were deemed not harmful to health. However, electromagnetic field values varied based on the distance between students, other electronic devices such as a desktop computers, and student posture while using a TPC. Based on these results, it is necessary to guide students to observe proper posture and to arrange seats at an appropriate distance in the classroom.

  13. Descriptive Study of Electromagnetic Wave Distribution for Various Seating Positions: Using Digital Textbooks

    Science.gov (United States)

    Seomun, GyeongAe; Kim, YoungHwan; Lee, Jung-Ah; Jeong, KwangHoon; Park, Seon-A; Kim, Miran; Noh, Wonjung

    2014-01-01

    To better understand environmental electromagnetic wave exposure during the use of digital textbooks by elementary school students, we measured numeric values of the electromagnetic fields produced by tablet personal computers (TPCs). Specifically, we examined the distribution of the electromagnetic waves for various students' seating positions in…

  14. Restraint use and seating position among children in motor vehicles ...

    African Journals Online (AJOL)

    Just over a third of the children were seated on the front seat of the vehicle, ... meaning adult will be dislodged by the huge gravitational forces in the case of an ..... action. 2009. http://whqlibdoc.who.int/publications/2009/9789241563840_.

  15. AGS BOOSTER BEAM POSITION, TUNE, AND LONGITUDINAL PROFILE DATA ACQUISITION SYSTEM

    International Nuclear Information System (INIS)

    BROWN, K.A.; AHRENS, L.; SEVERINO, F; SMITH, K.; WILINSKI, M

    2003-01-01

    In this paper we will describe a data acquisition system designed and developed for the AGS Booster. The system was motivated by the need to get high quality beam diagnostics from the AGS Booster. This was accomplished by locating the electronics and digital data acquisition close to the Booster ring, to minimize loss of bandwidth in the original signals. In addition we had to develop the system rapidly and at a low cost. The system consists of a Lecroy digital oscilloscope which is interfaced through a National Instruments LabView(trademark) server application, developed for this project. This allows multiple client applications to time share the scope without interfering with each other. We will present a description of the system design along with example clients that we have implemented

  16. The influence of occupant anthropometry and seat position on ejection risk in a rollover.

    Science.gov (United States)

    Atkinson, Theresa; Fras, Andrew; Telehowski, Paul

    2010-08-01

    During rollover crashes, ejection increases an occupant's risk of severe to fatal injury as compared to risks for those retained in the vehicle. The current study examined whether occupant anthropometry might influence ejection risk. Factors such as restraint use/disuse, seating position, vehicle type, and roll direction were also considered in the analysis. The current study examined occupant ejections in 10 years of National Automotive Sampling System (NASS) single-event rollovers of passenger vehicles and light trucks. Statistical analysis of unweighted and weighted ejection data was carried out. No statistically significant differences in ejection rates were found based on occupant height, age, or body mass index. Drivers were ejected significantly more frequently than other occupants: 62 percent of unrestrained drivers were ejected vs. 51 percent unrestrained right front occupants. Second row unrestrained occupants were ejected at rates similar to right front-seated occupants. There were no significant differences in ejection rates for near- vs. far-side occupants. These data suggest that assessment of ejection prevention systems using either a 50th or 5th percentile adult anthropomorphic test dummy (ATD) might provide a reasonable measure of system function for a broad range of occupants. They also support the development of ejection mitigation technologies that extend beyond the first row to protect occupants in rear seat positions. Future studies should consider potential interaction effects (i.e., occupant size and vehicle dimensions) and the influence of occupant size on ejection risk in non-single-event rollovers.

  17. Rear-facing car seat (image)

    Science.gov (United States)

    A rear-facing car seat position is recommended for a child who is very young. Extreme injury can occur in an accident because ... child. In a frontal crash a rear-facing car seat is best, because it cradles the head, ...

  18. The Impact of Seating Location and Seating Type on Student Performance

    OpenAIRE

    Meeks, Michael; Knotts, Tami; James, Karen; Williams, Felice; Vassar, John; Wren, Amy

    2013-01-01

    While an extensive body of research exists regarding the delivery of course knowledge and material, much less attention has been paid to the performance effect of seating position within a classroom. Research findings are mixed as to whether students in the front row of a classroom outperform students in the back row. Another issue that has not been fully examined in higher education is the effect of environmental factors, specifically seating type, on student performance. This study examines...

  19. Applications of Mechatronics in Seating Furniture

    Directory of Open Access Journals (Sweden)

    Hynek Maňák

    2014-01-01

    Full Text Available Mechatronics is gradually being used in different fields of the production process and final products. In the field of home seating furniture, it has not been formally declared as such yet. The purpose of further development of seating furniture is to improve its ergonomic parameters, to improve user comfort in controlling and using seating furniture or to provide new additional functions of seating furniture. Application of mechatronic principles can be presumed within the framework of this development. An analysis of the current state of reclining seating furniture, which uses mechanical and electromechanical positioning mechanisms, is conducted in order to formulate possible fields of applying mechatronics. The analysis defines individual ergonomic parameters which are influenced in reclining of seating furniture. This analysis is used as a basis for formulating a hypothesis describing potential development fields of applying mechatronics in home seating furniture.

  20. Injection Bucket Jitter Compensation Using Phase Lock System at Fermilab Booster

    Energy Technology Data Exchange (ETDEWEB)

    Seiya, K. [Fermilab; Drennan, C. [Fermilab; Pellico, W. [Fermilab; Chaurize, S. [Fermilab

    2017-05-12

    The extraction bucket position in the Fermilab Booster is controlled with a cogging process that involves the comparison of the Booster rf count and the Recycler Ring revolution marker. A one rf bucket jitter in the ex-traction bucket position results from the variability of the process that phase matches the Booster to the Recycler. However, the new slow phase lock process used to lock the frequency and phase of the Booster rf to the Recycler rf has been made digital and programmable and has been modified to correct the extraction notch position. The beam loss at the Recycler injection has been reduced by 20%. Beam studies and the phase lock system will be discussed in this paper.

  1. Comparison of knee flexion isokinetic deficits between seated and prone positions after ACL reconstruction with hamstrings graft: Implications for rehabilitation and return to sports decisions.

    Science.gov (United States)

    Koutras, Georgios; Bernard, Manfred; Terzidis, Ioannis P; Papadopoulos, Pericles; Georgoulis, Anastasios; Pappas, Evangelos

    2016-07-01

    Hamstrings grafts are commonly used in ACL reconstruction, however, the effect of graft harvesting on knee flexion strength has not been longitudinally evaluated in functional positions. We hypothesized that greater deficits in knee flexion strength exist in the prone compared to the seated position and these deficits remain as rehabilitation progresses. Case series. Forty-two consecutive patients who underwent ACL reconstruction with a hamstrings graft were followed prospectively for 9 months. Isokinetic knee flexion strength at a slow and a fast speed were collected at 3, 4, 6, and 9 months in two different positions: conventional (seated) and functional (0° of hip flexion). Peak torque knee flexion deficits were higher in the prone position compared to the seated position by an average of 6.5% at 60°/s and 9.1% at 180°/s (p<0.001). Measuring knee flexion strength in prone demonstrates higher deficits than in the conventional seated position. Most athletes would not be cleared to return to sports even at 9 months after surgery with this method. Copyright © 2015 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

  2. Environmental and psychosocial factors affecting seat belt use among Turkish front-seat occupants in Ankara: two observation studies.

    Science.gov (United States)

    Simşekoğlu, Ozlem; Lajunen, Timo

    2008-01-01

    Low seat belt use rate among car occupants is one of the main problems contributing to low driver and passenger safety in Turkey, where injury and fatality rates of car occupants are very high in traffic crashes. The present article consists of two observation studies, which were conducted in Ankara. The first study aimed at investigating environmental factors and occupant characteristics affecting seat belt use among front-seat occupants, and the objective of the second study was to investigate the relationship between driver and front-seat passenger seat belt use. In the first study, 4, 227 front-seat occupants (drivers or front seat passengers) were observed on four different road sides and, in the second study 1, 398 front seat occupants were observed in car parks of five different shopping centers in Ankara. In both observations, front-seat occupants' seat bet use (yes, no), sex (male, female), and age ( 50 years) were recorded. The data were analyzed using chi-square statistics and binary logistic regression techniques. Results of the first study showed that seat belt use proportion among observed front seat occupants was very low (25%). Being female and traveling on intercity roads were two main factors positively related to use a seat belt among front-seat occupants. High correlations between seat belt use of the drivers and front-seat passengers were found in the second study. Overall, low seat belt use rate (25%) among the front-seat occupants should be increased urgently for an improved driver and passenger safety in Turkey. Seat belt campaigns especially tailored for male front-seat occupants and for the front-seat occupants traveling on city roads are needed to increase seat belt use rates among them. Also, both drivers and passengers may have an important role in enforcing seat belt use among themselves.

  3. Diamond Light Source Booster fast orbit feedback system

    International Nuclear Information System (INIS)

    Gayadeen, S.; Duncan, S.R.; Christou, C.; Heron, M.T.; Rowland, J.

    2012-01-01

    The Fast Orbit Feedback system that has been installed on the Diamond Light Source Storage ring has been replicated on the Booster synchrotron in order to provide a test bed for the development of the Storage Ring controller design. To realise this the Booster is operated in DC mode. The electron beam is regulated in two planes using the Fast Orbit Feedback system, which takes the beam position from 22 beam position monitors for each plane, and calculates offsets to 44 corrector power supplies at a sample rate of 10 kHz. This paper describes the design and realization of the controller for the Booster Fast Orbit Feedback, presents results from the implementation and considers future development

  4. Booster gold beam injection efficiency and beam loss

    International Nuclear Information System (INIS)

    Zhang, S.Y.; Ahrens, L.A.

    1998-01-01

    The Relativistic Heavy Ion Collider (RHIC) at the BNL requires the AGS to provide Gold beam with the intensity of 10 9 ions per bunch. Over the years, the Tandem Van de Graaff has provided steadily increasing intensity of gold ion beams to the AGS Booster. However, the gold beam injection efficiency at the Booster has been found to decrease with the rising intensity of injected beams. As the result, for Tandem beams of the highest intensity, the Booster late intensity is lower than with slightly lower intensity Tandem beam. In this article, the authors present two experiments associated with the Booster injection efficiency and beam intensity. One experiment looks at the Booster injection efficiency by adjusting the Tandem beam intensity, and another looks at the beam life time while scraping the beam in the Booster. The studies suggest that the gold beam injection efficiency at the AGS Booster is related to the beam loss in the ring, rather than the intensity of injected beam or circulating beam. A close look at the effect of the lost gold ion at the Booster injection leads to the prediction that the lost gold ion creates large number of positive ions, and even larger number of electrons. The lost gold beam is also expected to create large numbers of neutral particles. In 1998 heavy ion run, the production of positive ions and electrons due to the lost gold beam has been observed. Also the high vacuum pressure due to the beam loss, presumably because of the neutral particles it created, has been measured. These results will be reported elsewhere

  5. Benefits of Seating and Positioning on the Wheelchairs and Factors that Interfere with its Use: a systematic review

    Directory of Open Access Journals (Sweden)

    Micaele Kedma Ribeiro de Moraes

    2016-12-01

    Full Text Available Seating and positioning are an assistive technology resource that aims to improve functional performance in the wheelchair. The aim of this paper was to find in the literature studies that addressed the benefits of seating and positioning in a wheelchair and factors that interfere with the prescription and use of this technology. Articles found that discuss the benefits addressed: the functionality and respiratory function; the pressure ulcer prevention; and user satisfaction and the family with assistive technology. Articles discussing the factors linked to prescription and use of adapting wheelchairs are those that address the environmental factors, components and wheelchair accessories. There are factors involved in the prescription process to achieve its benefits through its use, the prescribed process must have an interdisciplinary and biopsychosocial approach applied individually to each patient.

  6. Momentum Cogging at the Fermilab Booster

    International Nuclear Information System (INIS)

    Seiya, K.; Drennan, C.C.; Pellico, W.; Triplett, A.K.; Waller, A.M.

    2012-01-01

    The Fermilab Booster has an upgrade plan called the Proton Improvement Plan (PIP). The flux throughput goal is 2E17 protons/hour which, is almost double the present flux, 1.1E17 protons/hour. The beam loss in the machine is going to be an issue. The Booster accelerates beam from 400 MeV to 8 GeV and extracts to the Main Injector (MI). The current cogging process synchronizes the extraction kicker gap to the MI by changing radial position of the beam during the cycle. The gap creation occurs at about 700 MeV, which is about 6 ms into the cycle. The cycle-to-cycle variations of the Booster are larger at lower energy. However, changing the radial position at low energy for cogging is limited because of aperture. Momentum cogging is able to move the gap creation to an earlier time by using dipole correctors and radial position feedback, and is able to control the revolution frequency and radial position at the same time. The new cogging is expected to reduce beam loss and not be limited by aperture. The progress of the momentum cogging system development is going to be discussed in this paper.

  7. Shoulder Pain in Cases of Spinal Injury: Influence of the Position of the Wheelchair Seat

    Science.gov (United States)

    Giner-Pascual, Manuel; Alcanyis-Alberola, Modesto; Millan Gonzalez, Luis; Aguilar-Rodriguez, Marta; Querol, Felipe

    2011-01-01

    The objective of this study was to determine the relationship between shoulder pain and the position of the seat of a wheelchair relative to the ground and to determine the relationship between shoulder pain and structural damage. A transversal study of a patient cohort of 140 patients with grade A and B spinal cord injuries below the T1 vertebra,…

  8. Immunity booster

    International Nuclear Information System (INIS)

    Stefanescu, Ioan; Titescu, Gheorghe; Tamaian, Radu; Haulica, Ion; Bild, Walther

    2002-01-01

    The immunity booster is, according to its patent description, microbiologically pure water with an D/(D+H) isotopic concentration of 100 ppm, with physical-chemical characteristics similar to those of distilled water. It is obtained by sterilization of a mixture of deuterium depleted water, with a 25 ppm isotopic concentration, with distilled water in a volume ratio of 4:6. Unlike natural immunity boosters (bacterial agents as Bacillus Chalmette-Guerin, Corynebacterium parvum; lipopolysaccharides; human immunoglobulin) or synthetical products (levamysol; isoprinosyne with immunostimulating action), which cause hypersensitivity and shocks, thrill, fever, sickness and the immunity complex disease, the water of 100 ppm D/(D + H) isotopic concentration is a toxicity free product. The testing for immune reaction of the immunity booster led to the following results: - an increase of cell action capacity in the first immunity shielding stage (macrophages), as evidenced by stimulation of a number of essential characterizing parameters, as well as of the phagocytosis capacity, bactericide capacity, and opsonic capacity of serum; - an increase of the number of leucocyte particularly of the granulocyte in peripheral blood, produced especially when medullar toxic agents like caryolysine are used; - it hinders the effect of lowering the number of erythrocytes in peripheral blood produced by experimentally induced chronic inflammation; - an increase of nonspecific immunity defence capacity against specific bacterial aggression of both Gram-positive bacteria (Streptococcus pneumoniae 558 ) and of the Gram-negative ones (Klebsiella pneumoniae 507 ); - an increase of immunity - stimulating activity (proinflamatory), like that of levamisole as evidenced by the test of stimulation of experimentally induced inflammation by means of carrageenan. The following advantages of the immunity booster are stressed: - it is toxicity free and side effect free; - can be orally administrated as

  9. Discrepancies between knowledge and practice of childhood motor vehicle occupant safety in Nova Scotia--a population-based study.

    Science.gov (United States)

    Yanchar, Natalie L; Kirkland, Susan A; LeBlanc, John C; Langille, Donald B

    2012-03-01

    To determine discrepancies between knowledge and practice of childhood motor vehicle restraints (CMVRs) and vehicle seating position amongst parents within the province of Nova Scotia. Random telephone survey. The Canadian province of Nova Scotia. Four hundred and twenty-six households with at least one child under the age of 12 years, totaling 723 children. The proportion of parents whose children who should be in a specific stage of CMVR and sitting in the rear seat of the vehicle, and who demonstrate correct knowledge of that restraint system and seating position, yet do not use that restraint system/seating position for their child (demonstrate practice discrepant from their knowledge). Awareness of what restraint system to use is good (>80%). However, knowledge of when it is safe to graduate to the next stage is low (30-55%), most marked for when to use a seatbelt alone. Awareness of the importance of sitting in the rear seat of a vehicle was universal. Discrepancies between knowledge and practice were most marked with booster seats and rear-seating of older children. Factors influencing incorrect practice (prematurely graduated to a higher-level restraint system than what is appropriate for age and weight) included lower household income, caregiver education level, and knowledge of when to graduate from forward-facing car seats and booster seats. Incorrect practice was also more commonly observed amongst children of weight and/or age approaching (but not yet reaching) recommended graduation parameters of the appropriate CMVR. Discrepancies between knowledge and practice are evident through all stages of CMVRs, but most marked with booster seats. The roles of lower socioeconomic status and gaps in CMVR legislation, in influencing discrepant practice, must be acknowledged and suggest the need for targeted education concurrent with development of comprehensive all-stages CMVR policies. Copyright © 2011 Elsevier Ltd. All rights reserved.

  10. RF cogging in the FNAL Booster Accelerator

    International Nuclear Information System (INIS)

    William A. Pellico and Robert C. Webber

    2000-01-01

    The Fermilab Booster operates at a Radio Frequency (RF) harmonic number of 84 with beam in all buckets. One or two bunches of beam are systematically lost in the 8 GeV extraction process as beam is swept across a magnetic septum during the extraction kicker rise time. The prompt radiation and component activation resulting from this localized high energy beam loss become serious concerns as Booster beam throughput must be increased more than tenfold to meet the requirements of RUN II, NUMI, and MiniBooNE experiments. Synchronizing a gap in the beam to the firing of the extraction kickers, a relatively easy and standard practice in many machines, can eliminate the problem. This seemingly simple operation is greatly complicated in the Booster by the need to synchronize extraction to beam already circulating in the Main Injector. Coupled with the inflexibility of the Booster resonant magnetic cycle, cycle to cycle variations, and constraints inherent in the accelerator physics, that requirement forces active control of the gap's azimuthal position throughout the acceleration process as the revolution frequency sweeps rapidly. Until recently, the complexities of actually implementing and demonstrating this process in the Booster had not been worked out. This paper describes a successful demonstration of gap cogging in the Booster

  11. Elderly road collision injury outcomes associated with seat positions and seatbelt use in a rapidly aging society-A case study in South Korea.

    Directory of Open Access Journals (Sweden)

    Yuna Noh

    Full Text Available Aging has long been regarded as one of the most critical factors affecting crash injury outcomes. In South Korea, where the elderly population is projected to reach 35.9% by 2050, the implications of an increasing number of elderly vehicle users on road safety are evident. In this research, the confounding effect of occupant age in a vehicle in terms of seat position and seatbelt use was investigated. In addition, elderly occupants were divided into a younger-old group aged between 65 and 74 years and an older-old group aged 75 years and older in an effort to assess whether the conventional elderly age standard of 65 years should be reconsidered.A multinomial logit framework was adopted to predict two-level injury severity using collision data between 2008 and 2015. Predictor variables included gender, age group, seat position, seatbelt, road type, road slope, road surface, road line, and type of vehicle. Five models, a base model with no interactions and four interaction models which were combinations of age group, seatbelt use and seat position, were devised and evaluated.With no interacting term, age was the most prominent predictor. Elderly occupants were most likely to suffer from severe injury without a seatbelt in all seat positions, and the use of a seatbelt reduced this likelihood the most in the elderly group as well. Front passenger seats had the highest risk to elderly occupants, while the driver seat was statistically insignificant. When the elderly group was divided into the younger-old group and the older-old group, the older-olds were found to be much more vulnerable compared to the younger-olds. In particular, older drivers were five times more likely to suffer a severe injury without a seatbelt.The degree of injury severity of elderly occupants was reduced the most with the use of a seatbelt, demonstrating the importance of using seat restraints. The sharp increase in the risk of injury of the older-old group suggests that the

  12. Elderly road collision injury outcomes associated with seat positions and seatbelt use in a rapidly aging society-A case study in South Korea.

    Science.gov (United States)

    Noh, Yuna; Yoon, Yoonjin

    2017-01-01

    Aging has long been regarded as one of the most critical factors affecting crash injury outcomes. In South Korea, where the elderly population is projected to reach 35.9% by 2050, the implications of an increasing number of elderly vehicle users on road safety are evident. In this research, the confounding effect of occupant age in a vehicle in terms of seat position and seatbelt use was investigated. In addition, elderly occupants were divided into a younger-old group aged between 65 and 74 years and an older-old group aged 75 years and older in an effort to assess whether the conventional elderly age standard of 65 years should be reconsidered. A multinomial logit framework was adopted to predict two-level injury severity using collision data between 2008 and 2015. Predictor variables included gender, age group, seat position, seatbelt, road type, road slope, road surface, road line, and type of vehicle. Five models, a base model with no interactions and four interaction models which were combinations of age group, seatbelt use and seat position, were devised and evaluated. With no interacting term, age was the most prominent predictor. Elderly occupants were most likely to suffer from severe injury without a seatbelt in all seat positions, and the use of a seatbelt reduced this likelihood the most in the elderly group as well. Front passenger seats had the highest risk to elderly occupants, while the driver seat was statistically insignificant. When the elderly group was divided into the younger-old group and the older-old group, the older-olds were found to be much more vulnerable compared to the younger-olds. In particular, older drivers were five times more likely to suffer a severe injury without a seatbelt. The degree of injury severity of elderly occupants was reduced the most with the use of a seatbelt, demonstrating the importance of using seat restraints. The sharp increase in the risk of injury of the older-old group suggests that the age standard of

  13. SEAT BELT USE AMONG CAR USERS IN MALAYSIA

    Directory of Open Access Journals (Sweden)

    S. KULANTHAYAN

    2004-01-01

    Full Text Available The car is the second (40% most common mode of transportation in Malaysia. In terms of fatal road accidents, car drivers constitute about 9.0% and passengers 13.6% of fatalities. The major cause of car occupants' fatality in such accidents is head injuries, which consist of more than half (56.4% of the fatalities. Thus restraining the head and body, the initial position is the most important injury control strategy for car users. The use of seat belts was deemed one of the most effective ways to reduce road accident fatalities in Malaysia and consequently the mandatory seat belt law was enforced in the early seventies. Therefore, a study on factors influencing the compliance behaviour of seat belt use among cars is needed as to date no such research has been undertaken in Malaysia. A questionnaire study was carried out in Selangor, Malaysia on the compliance behaviour of car occupants in relation to seat belt use. A total of 237 respondents were interviewed and the data analysed using logistic regression method. Six variables were found to be significant at 5 percent level (p<0.05: seating position, location of travel, education level, speeding, night-time driving and enforcement. Compliance with the seat belt law was higher among drivers, educated car users, in the presence of enforcement activities, travelling in city-center areas and car users with a positive attitude towards the risks of speeding and night driving.

  14. Traffic Safety Facts - Research Note: Additional Analysis of National Child Restraint Use Special Study: Characteristics Of Those Not Restrained

    Science.gov (United States)

    2018-03-01

    The National Child Restraint Use Special Study (NCRUSS) recorded the use of car seats and belt-positioning booster seats in children up to 8 years old in 4,167 vehicles. Observers approached vehicles that carried at least one child. They interviewed ...

  15. BROOKHAVEN: Booster boost

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    After three months of intensive dedicated machine studies, Brookhaven's new Booster accelerated 5 x 10 13 protons over four cycles, about 85% of the design intensity. This was made possible by careful matching of Linac beam into the Booster and by extensive resonance stop band corrections implemented during Booster acceleration. The best single cycle injection into the AGS Alternating Gradient Synchrotron was 1.14 x 10 13 protons from the Booster. 1.05 x 10 13 protons were kept in the AGS, a 92% combined efficiency of extraction, transfer, and injection. The maximum injected 1994 shutdown period, enabling the 1994 physics run to make use of the full Booster intensity and go for the stated AGS objective of 4x10 13 protons per pulse

  16. The Effects of Prototype Helicopter Seat Cushion Concepts on Human Body Vibration Response

    National Research Council Canada - National Science Library

    Smith, Suzanne

    1998-01-01

    ...), and thigh, and the input at the seat. Seating configurations included the rigid seat, a current inventory seat cushion, and a prototype cushion with an inflatable thigh support in both the deflated and inflated positions...

  17. Car Seat Safety

    Science.gov (United States)

    ... Staying Safe Videos for Educators Search English Español Car Seat Safety KidsHealth / For Parents / Car Seat Safety ... certified child passenger safety technician.) Guidelines for Choosing Car Seats Choose a seat with a label that ...

  18. Logic and control module for the Fermilab booster beam damper

    International Nuclear Information System (INIS)

    Sandberg, B.R.

    1977-01-01

    A logic and control module is included in the electronic system of the booster superdamper. This module produces a 9-bit digital word that controls the delay of beam bunch position information in the Fermilab booster synchrotron so that it arrives at the damping electrodes at the same time as the bunch of beam to be corrected. This delay word generator also has an output feature that only allows delay time decreases as the booster synchrotron frequency program increases monotonically. Such a feature guards against low-index incidental FM from affecting the delay computations

  19. Effect of different seated positions on lung volume and oxygenation in acute respiratory distress syndrome.

    Science.gov (United States)

    Dellamonica, J; Lerolle, N; Sargentini, C; Hubert, S; Beduneau, G; Di Marco, F; Mercat, A; Diehl, J L; Richard, J C M; Bernardin, G; Brochard, L

    2013-06-01

    Lung volume available for ventilation is markedly decreased during acute respiratory distress syndrome. Body positioning may contribute to increase lung volume and partial verticalization is simple to perform. This study evaluated whether verticalization had parallel effects on oxygenation and end expiratory lung volume (EELV). Prospective multicenter study in 40 mechanically ventilated patients with ALI/ARDS in five university hospital MICUs. We evaluated four 45-min successive trunk position epochs (supine slightly elevated at 15°; semi recumbent with trunk elevated at 45°; seated with trunk elevated at 60° and legs down at 45°; back to supine). Arterial blood gases, EELV measured using the nitrogen washin/washout, and static compliance were measured. Responders were defined by a PaO₂/FiO₂ increase >20 % between supine and seated position. Results are median [25th-75th percentiles]. With median PEEP = 10 cmH₂O, verticalization increased lung volume but only responders (13 patients, 32 %) had a significant increase in EELV/PBW (predicted body weight) compared to baseline. This increase persisted at least partially when patients were positioned back to supine. Responders had a lower EELV/PBW supine [14 mL/kg (13-15) vs. 18 mL/kg (15-27) (p = 0.005)] and a lower compliance [30 mL/cmH₂O (22-38) vs. 42 (30-46) (p = 0.01)] than non-responders. Strain decreased with verticalization for responders. EELV/PBW increase and PaO₂/FiO₂ increase were not correlated. Verticalization is easily achieved and improves oxygenation in approximately 32 % of the patients together with an increase in EELV. Nonetheless, effect of verticalization on EELV/PBW is not predictable by PaO₂/FiO₂ increase, its monitoring may be helpful for strain optimization.

  20. Does obesity affect the position of seat belt loading in occupants involved in real-world motor vehicle collisions?

    Science.gov (United States)

    Hartka, Thomas R; Carr, Hannah M; Smith, Brittany R; Melmer, Monica; Sochor, Mark R

    2018-02-28

    Previous work has shown that the lap belt moves superior and forward compared to the bony pelvis as body mass index (BMI) increases. The goal of this project was to determine whether the location of lap belt loading is related to BMI for occupants who sustained real-world motor vehicle collisions (MVCs). A national MVC database was queried for vehicle occupants over a 10-year period (2003-2012) who were at least 16 years old, restrained by a 3-point seat belt, sitting in the front row, and involved in a front-end collision with a change in velocity of at least 56 km/h. Cases were excluded if there was not an available computed tomography (CT) scan of the abdomen. CT scans were then analyzed using adipose enhancement of 3-dimensional reconstructions. Scans were assessed for the presence a radiographic seat belt sign (rSBS), or subcutaneous fat stranding due to seat belt loading. In scans in which the rSBS was present, anterior and superior displacement of rSBS from the anterior-superior iliac spine (ASIS) was measured bilaterally. This displacement was correlated with BMI and injury severity. The inclusion and exclusion criteria yielded 151 cases for analysis. An rSBS could definitively be identified in 55 cases. Cases in which occupants were older and had higher BMI were more likely to display an rSBS. There was a correlation between increasing BMI and anterior rSBS displacement (P obesity may worsen horizontal position but not the vertical position of the lap belt loading during real-world frontal MVCs.

  1. The PS booster

    CERN Multimedia

    CERN PhotoLab

    1972-01-01

    The PS booster which accelerates protons from the linac at an energy of 50 MeV to an energy of 800 MeV before injecting them into the main magnet ring of the synchrotron. The booster consists of four superposed rings. In the photograph can be seen the input beam line from the linac and the output beam lines, where beams from the four booster levels have been combined into two beams before final recombination.

  2. Kinematics of child volunteers and child anthropomorphic test devices during emergency braking events in real car environment.

    Science.gov (United States)

    Stockman, Isabelle; Bohman, Katarina; Jakobsson, Lotta; Brolin, Karin

    2013-01-01

    The objective of this study was to present, compare, and discuss the kinematic response of children and child anthropomorphic test devices (ATDs) during emergency braking events in different restraint configurations in a passenger vehicle. A driving study was conducted on a closed-circuit test track comprising 16 children aged 4 to 12 years old and the Q3, Hybrid III (HIII) 3-year-old, 6-year-old, and 10-year-old ATDs restrained on the right rear seat of a modern passenger vehicle. The children were exposed to one braking event in each of the 2 restraint systems and the ATDs were exposed to 2 braking events in each restraint system. All events had a deceleration of 1.0 g. Short children (stature 107-123 cm) and the Q3, HIII 3-year-old, and 6-year-old were restrained on booster cushions as well as high-back booster seats. Tall children (stature 135-150 cm) and HIII 10-year-old were restrained on booster cushions or restrained by 3-point belts directly on the car seat. Vehicle data were collected and synchronized with video data. Forward trajectories for the forehead and external auditory canal (ear) were determined as well as head rotation and shoulder belt force. A total of 40 trials were analyzed. Child volunteers had greater maximum forward displacement of the head and greater head rotation compared to the ATDs. The average maximum displacement for children ranged from 165 to 210 mm and 155 to 195 mm for the forehead and ear target, respectively. Corresponding values for the ATDs were 55 to 165 mm and 50 to 160 mm. The change in head angle was greater for short children than for tall children. Shoulder belt force was within the same range for short children when restrained on booster cushions or high-back booster seats. For tall children, the shoulder belt force was greater when restrained on booster cushions compared to being restrained by seat belts directly on the car seat. The forward displacement was within the same range for all children regardless of

  3. Seat belt reminders.

    NARCIS (Netherlands)

    2008-01-01

    Seat belts are an effective way of reducing the number or road deaths and severe road injuries in crashes. Seat belt reminders warn car drivers and passengers if the seat belt is not fastened. This can be done by a visual signal or an acoustic signal or by a combination of the two. Seat belt

  4. The Impact of Seating Location and Seating Type on Student Performance

    Science.gov (United States)

    Meeks, Michael D.; Knotts, Tami L.; James, Karen D.; Williams, Felice; Vassar, John A.; Wren, Amy Oakes

    2013-01-01

    While an extensive body of research exists regarding the delivery of course knowledge and material, much less attention has been paid to the performance effect of seating position within a classroom. Research findings are mixed as to whether students in the front row of a classroom outperform students in the back row. Another issue that has not…

  5. 49 CFR 571.210 - Standard No. 210; Seat belt assembly anchorages.

    Science.gov (United States)

    2010-10-01

    ... bolt holes or the centroid of any other means of attachment to the structure specified in 4.1.3.1... are either: (a) For designated seating positions that are common to the same occupant seat and that... common to the same occupant seat, but that face in the same direction, if the vertical centerline of the...

  6. Tilted seat position for non-ambulant individuals with neurological and neuromuscular impairment: a systematic review.

    Science.gov (United States)

    Michael, S M; Porter, D; Pountney, T E

    2007-12-01

    To determine the effects of tilt-in-space seating on outcomes for people with neurological or neuromuscular impairment who cannot walk. Search through electronic databases (MEDLINE, Embase, CINAHL, AMED). Discussions with researchers who are active in field. Selection criteria included interventional studies that investigated the effects of seat tilt on outcome or observational studies that identified outcomes for those who had used tilt-in-space seating in populations with neurological or neuromuscular impairments. Two reviewers independently selected trials for inclusion, assessed quality and extracted data. Nineteen studies were identified which fulfilled the selection criteria. Seventeen of these were essentially before-after studies investigating the immediate effects of tilting the seating. All studies looked at populations with neurological impairment, and most were on children with cerebral palsy (n=8) or adults with spinal cord injury (n=8). REVIEWER'S CONCLUSION: Posterior tilt can reduce pressures at the interface under the pelvis.

  7. Performance evaluation of DAAF as a booster material using the onionskin test

    Energy Technology Data Exchange (ETDEWEB)

    Morris, John S [Los Alamos National Laboratory; Francois, Elizabeth G [Los Alamos National Laboratory; Hooks, Daniel E [Los Alamos National Laboratory; Hill, Larry G [Los Alamos National Laboratory; Harry, Herbert H [Los Alamos National Laboratory

    2010-12-02

    Initiation of insensitive high explosive (IHE) formulations requires the use of a booster explosive in the initiation train. Booster material selection is crucial, as the initiation must reliably function across some spectrum of physical parameters. The interest in Diaminoazoxyfurazan (DAAF) for this application stems from the fact that it possesses many traits of an IHE but is shock sensitive enough to serve as an explosive booster. A hemispherical wave breakout test, termed the onionskin test, is one of the methods used to evaluate the performance of a booster material. The wave breakout time-position history at the surface of a hemispherical IHE charge is recorded and the relative uniformity of the breakout can be quantitatively compared between booster materials. A series of onionskin tests were performed to investigate breakout and propagation diaminoazoxyfurazan (DAAF) at low temperatures to evaluate ignition and detonation spreading in comparison to other explosives commonly used in booster applications. Some wave perturbation was observed with the DAAF booster in the onionskin tests presented. The results of these tests will be presented and discussed.

  8. NSLS-II booster timing system

    International Nuclear Information System (INIS)

    Cheblakov, P.; Karnaev, S.; De Long, J.

    2012-01-01

    NSLS-II light source includes the main storage ring with beam lines and injection part consisting of 200 MeV linac, a full-energy 3 GeV booster synchrotron and two transport lines. The booster timing system is a part of NSLS-II timing system which uses hardware from MicroResearch Finland: Event Generator (EVG) and Event Receivers (EVRs). The booster timing is based on the events coming from NSLS-II EVG: 'Pre-Injection', 'Injection', 'Pre-Extraction', 'Extraction'. These events are referenced to the selected RF bucket of the storage ring and correspond to the first RF bucket of the booster. EVRs provide triggers both for the injection and the extraction pulse devices. EVRs also provide the timing of booster cycle operation and generation of events for cycle-to-cycle updates of pulsed and ramping parameters, and synchronization of the booster beam instrumentation devices. This paper describes the final design of the booster timing system. The timing system functional diagrams and block diagram are presented. (authors)

  9. Knowledge, attitude and use of seat belt among commercial drivers in Sokoto Metropolis

    Directory of Open Access Journals (Sweden)

    A O Abiola

    2010-01-01

    Conclusion: This study has identified high level of knowledge, positive attitude and reported use of seat belt. It is recommended that public awareness of the safety benefits of seat belts and strong enforcement are necessary to achieve optimal use of seat belt.

  10. High levels of incorrect use of car seat belts and child restraints in Fife--an important and under-recognised road safety issue.

    Science.gov (United States)

    Campbell, H; Macdonald, S; Richardson, P

    1997-03-01

    To pilot data collection instruments and to make a preliminary estimate of the level of incorrect use of car seat belts and child restraints in Fife, Scotland. Cross sectional survey of cars containing adults and children at a number of public sites across Fife in 1995 to assess use of car occupant restraints. Trained road safety officers assessed whether seat restraints were appropriate for the age of the passengers and whether restraints were used correctly. These assessments were based on standards published by the Child Accident Prevention Trust. The survey gathered data from 596 occupants in 180 cars: 327 adults and 269 children. Ten per cent of drivers who were approached refused to participate. Car occupant restraint was assessed in 180 drivers, 151 front seat passengers, and 265 rear seat passengers. Three hundred and sixty one occupants wore seat belts, 68 were restrained by a seat belt and booster cushion, 63 in toddler seats, 25 in two way seats, and 18 in rear facing infant carriers. Ninety seven per cent of drivers, 95% of front seat passengers, and 77% of rear seat passengers were restrained. However, in 98 (52%) vehicles at least one passenger was restrained by a device that was used incorrectly. Seven per cent of adults and 28% of children were secured incorrectly. The commonest errors were loose seat belts and restraint devices not adequately secured to the seat. Rates of incorrect use were highest in child seat restraints, reaching 60% with two way seats and 44% with rear facing infant seats. The incorrect use of car occupant restraints is an under-recognised problem, both by health professionals, and the general public. Incorrect use has been shown to reduce the effectiveness of restraints, can itself result in injury, and is likely to be an important factor in child passenger injuries. The correct use of car seat restraints merits greater attention in strategies aiming to reduce road traffic casualties. Areas of intervention that could be

  11. Operational behaviour of CO{sub 2} booster systems; Betriebsverhalten von CO{sub 2}-Booster-Systemen

    Energy Technology Data Exchange (ETDEWEB)

    Javerschek, Oliver; Hieble, Tobias [BITZER Kuehlmaschinenbau GmbH, Sindelfingen (Germany)

    2011-07-01

    The operating characteristics of booster systems and the resulting operating conditions of CO{sub 2} booster systems in supermarket refrigeration are explained and discussed. Criteria and challenges of different operating and load conditions are gone into. Simulated and measured operating states of a small-scale booster system are compared and evaluated. [German] In der vorliegenden Veroeffentlichung werden unterschiedliche Betriebsverhalten und die daraus resultierenden Betriebsbedingungen von CO{sub 2}-Booster-Systemen in der Supermarktkaelte erlaeutert und diskutiert. Dabei werden wesentliche Kriterien und Herausforderungen bei den unterschiedlichen Betriebs- und Lastbedingungen besprochen. Ausserdem werden simulierte und gemessene Betriebszustaende einer kleinen Booster-Kaelteanlage vergleichend betrachtet und bewertet.

  12. Effective seat-to-head transmissibility in whole-body vibration: Effects of posture and arm position

    Science.gov (United States)

    Rahmatalla, Salam; DeShaw, Jonathan

    2011-12-01

    Seat-to-head transmissibility is a biomechanical measure that has been widely used for many decades to evaluate seat dynamics and human response to vibration. Traditionally, transmissibility has been used to correlate single-input or multiple-input with single-output motion; it has not been effectively used for multiple-input and multiple-output scenarios due to the complexity of dealing with the coupled motions caused by the cross-axis effect. This work presents a novel approach to use transmissibility effectively for single- and multiple-input and multiple-output whole-body vibrations. In this regard, the full transmissibility matrix is transformed into a single graph, such as those for single-input and single-output motions. Singular value decomposition and maximum distortion energy theory were used to achieve the latter goal. Seat-to-head transmissibility matrices for single-input/multiple-output in the fore-aft direction, single-input/multiple-output in the vertical direction, and multiple-input/multiple-output directions are investigated in this work. A total of ten subjects participated in this study. Discrete frequencies of 0.5-16 Hz were used for the fore-aft direction using supported and unsupported back postures. Random ride files from a dozer machine were used for the vertical and multiple-axis scenarios considering two arm postures: using the armrests or grasping the steering wheel. For single-input/multiple-output, the results showed that the proposed method was very effective in showing the frequencies where the transmissibility is mostly sensitive for the two sitting postures and two arm positions. For multiple-input/multiple-output, the results showed that the proposed effective transmissibility indicated higher values for the armrest-supported posture than for the steering-wheel-supported posture.

  13. The dynamic response of human subjects while seated in car seats.

    Science.gov (United States)

    Pope, M H; Magnusson, M; Broman, N H; Hasson, T

    1998-01-01

    A pendulum impact method was used to establish the dynamic response of the seated subject. Threaded K wires were placed in the L3 spinous process. The gain and phase angle between the platform and the vertebra were established. The response of the subject was observed while seated on a platform and a variety of other seats. The seats were found to be very important in the attenuation of the impulse, leading to a higher transmissibility. Clinical Relevance Skeletal impact through the lower extremity is quite common in many occupations. The importance of posture and seat design in attenuation of impulses has been established.

  14. Frontal and oblique crash tests of HIII 6-year-old child ATD using real-world, observed child passenger postures.

    Science.gov (United States)

    Bohman, Katarina; Arbogast, Kristy B; Loeb, Helen; Charlton, Judith L; Koppel, Sjaan; Cross, Suzanne L

    2018-02-28

    The aim of this study was to evaluate the consequences of frontal and oblique crashes when positioning a Hybrid III (HIII) 6-year-old child anthropometric test device (ATD) using observed child passenger postures from a naturalistic driving study (NDS). Five positions for booster-seated children aged 4-7 years were selected, including one reference position according to the FMVSS 213 ATD seating protocol and 4 based on real-world observed child passenger postures from an NDS including 2 user positions with forward tilting torso and 2 that combined both forward and lateral inboard tilting of the torso. Seventeen sled tests were conducted in a mid-sized vehicle body at 64 km/h (European New Car Assessment Programme [Euro NCAP] Offset Deformable Barrier [ODB] pulse), in full frontal and oblique (15°) crash directions. The rear-seated HIII 6-year-old child ATD was restrained on a high-back booster seat. In 10 tests, the booster seat was also attached with a top tether. In the oblique tests, the ATD was positioned on the far side. Three camera views and ATD responses (head, neck, and chest) were analyzed. The shoulder belt slipped off the shoulder in all ATD positions in the oblique test configuration. In full frontal tests, the shoulder belt stayed on the shoulder in 3 out of 9 tests. Head acceleration and neck tension were decreased in the forward leaning positions; however, the total head excursion increased up to 210 mm compared to te reference position, due to belt slip-off and initial forward leaning position. These results suggest that real-world child passenger postures may contribute to shoulder belt slip-off and increased head excursion, thus increasing the risk of head injury. Restraint system development needs to include a wider range of sitting postures that children may choose, in addition to the specified postures of ATDs in seating test protocols, to ensure robust performance across diverse use cases. In addition, these tests revealed that the child

  15. The dynamic response of human subjects while seated in car seats.

    OpenAIRE

    Pope, M. H.; Magnusson, M.; Broman, N. H.; Hasson, T.

    1998-01-01

    A pendulum impact method was used to establish the dynamic response of the seated subject. Threaded K wires were placed in the L3 spinous process. The gain and phase angle between the platform and the vertebra were established. The response of the subject was observed while seated on a platform and a variety of other seats. The seats were found to be very important in the attenuation of the impulse, leading to a higher transmissibility. Clinical Relevance Skeletal impact through the lower ext...

  16. Blast resistant vehicle seat

    Science.gov (United States)

    Ripley, Edward B

    2013-02-12

    Disclosed are various seats for vehicles particularly military vehicles that are susceptible to attack by road-bed explosive devices such as land mines or improvised explosive devices. The seats often have rigid seat shells and may include rigid bracing for rigidly securing the seat to the chassis of the vehicle. Typically embodiments include channels and particulate media such as sand disposed in the channels. A gas distribution system is generally employed to pump a gas through the channels and in some embodiments the gas is provided at a pressure sufficient to fluidize the particulate media when an occupant is sitting on the seat.

  17. Experimental study on occupant evacuation in narrow seat aisle

    Science.gov (United States)

    Huang, Shenshi; Lu, Shouxiang; Lo, Siuming; Li, Changhai; Guo, Yafei

    2018-07-01

    Narrow seat aisle is an important area in the train car interior due to the large passenger population, however evacuation therein has not gained enough concerns. In this experimental study, the occupant evacuation of the narrow seat aisle area is investigated, with the aisle width of 0.4-0.6 m and the evacuation direction of forward and backward. The evacuation behaviors are analyzed based on the video record, and the discussion is carried out in the aspect of evacuation time, crowdedness, evacuation order, and aisle conflicts. The result shows that with the increasing aisle width, total evacuation time and the average specific evacuation rate decrease. The aisle is crowded for some time, with a large linear occupant densities. The evacuation order of each occupant is mainly related to the seat position. Moreover, it is found that the aisle conflicts can be well described by Burstedde's model. This study gives a useful benchmark for evacuation simulation of narrow seat aisle, and provides reference to safety design of seat area in train cars.

  18. 75 FR 31691 - Safety Standard for Infant Bath Seats: Final Rule

    Science.gov (United States)

    2010-06-04

    ... would actually make the requirement less restrictive than what is already in the voluntary standard. For... various water levels and possible head positions of occupants vs. angles of bath seats to determine what... instructional literature or warnings, it is foreseeable that caregivers will install the bath seat on a wet and...

  19. A field-based approach for examining bicycle seat design effects on seat pressure and perceived stability.

    Science.gov (United States)

    Bressel, Eadric; Bliss, Shantelle; Cronin, John

    2009-05-01

    The purpose of this study was to investigate the effect of various bicycle seat designs on seat pressure and perceived stability in male and female cyclists using a unique field-based methodology. Thirty participants, comprising male and female cyclists, pedaled a bicycle at 118W over a 350m flat course under three different seat conditions: standard seat, a seat with a partial anterior cutout, and a seat with a complete anterior cutout. The pressure between the bicycle seat and perineum of the cyclist was collected with a remote pressure-sensing mat, and perceived stability was assessed using a continuous visual analogue scale. Anterior seat pressure and stability values for the complete cutout seat were significantly lower (p<0.05; 62-101%) than values for the standard and partial cutout designs. These findings were consistent between males and females. Our results would support the contention that the choice of saddle design should not be dictated by interface pressure alone since optimal anterior seat pressure and perceived seat stability appear to be inversely related.

  20. Misuse of car safety seats.

    Science.gov (United States)

    Bull, M J; Stroup, K B; Gerhart, S

    1988-01-01

    Correct use of car seats for small children is essential to prevent serious injuries and death from automotive accidents. Failure to use a car seat properly can contribute to serious injury or death of a child. A case study in which misuse of a car seat occurred is reported. The infant died of hemorrhage and shock secondary to liver laceration which resulted from excessive pressure over the abdomen sustained on impact. Surveys of car seat use for small children prior to and following a child restraint law are also reported. Observers noted types of car seats and specific forms of misuse. Survey results suggest that parents are more likely to misuse car seats for infants than toddlers. Medical professionals can reinforce the importance of proper car seat use by incorporating specific car seat use questions into the patient interview and by providing educational materials.

  1. BROOKHAVEN: Booster commissioned

    Energy Technology Data Exchange (ETDEWEB)

    Bleser, Ed

    1992-03-15

    The construction and first commissioning phase of the Booster synchrotron to inject into Brookhaven's veteran Alternating Gradient Synchrotron (AGS) were completed last year. Scheduled to come into operation this year, the new Booster will extend the research capabilities AGS, and with its ability to accelerate partially stripped heavy ions will play an essential role in the chain of accelerators serving the Relativistic Heavy Ion Collider (RHIC)

  2. ANTHROPOMETRIC CHARACTERISTICS OF FLIGHT PERSONNEL FOR DESIGNING DAMPERS FOR SHOCKPROOF SEATS OF HELICOPTER CREWS.

    Science.gov (United States)

    Moiseev, Yu B; Ignatovich, S N; Strakhov, A Yu

    The article discusses anthropometric design of shockproof pilot seats for state-of-the-art helicopters. Object of the investigation was anthropometric parameters of the helicopter aviation personnel of the Russian interior troops. It was stated that the body parameters essential for designing helicopter seat dampers are mass of the body part that presses against the seat in the seating position, and eye level above the seat surface. An uncontrolled seat damper ensuring shockproof safety to 95 % helicopter crews must be designed for the body mass contacting the seat of 99.7 kg and eye level above the seat of 78.6 cm. To absorb.shock effectively, future dampers should be adjustable to pilot's body parameters. The optimal approach to anthropometric design of a helicopter seat is development of type pilot' body models with due account of pilot's the flight outfit and seat geometry. Principle criteria of type models are body mass and eye level. The authors propose a system of type body models facilitating specification of anthropometric data helicopter seat developers.

  3. Automated tuning of the advanced photon source booster synchrotron

    International Nuclear Information System (INIS)

    Biedron, S.G.; Milton, S.V.

    1997-01-01

    The acceleration cycle of the Advanced Photon Source (APS) booster synchrotron is completed within 223 ms and is repeated at 2 Hz. Unless properly corrected, transverse and longitudinal injection errors can lead to inefficient booster performance. In order to simplify daily operation, automated tuning methods have been developed. Through the use of beam position monitor (BPM) reading, transfer line corrector magnets, magnet ramp timing, and empirically determined response functions, the injection process is optimized by correcting the first turn trajectory to the measured closed orbit. These tuning algorithms and their implementation are described here along with an evaluation of their performance

  4. Design and testing of the AGS Booster BPM detector

    International Nuclear Information System (INIS)

    Thomas, R.; Ciardullo, D.J.; Van Zwienen, W.

    1991-01-01

    The AGS Booster beam position monitor system must accurately measure the position of beams and bunches over a wide range of intensity. The frequency of operation must also cover a wide range (600 kHz to 4.2 MHz) since the Booster accelerates both protons and heavy ions. Split-cylinder electrodes were chosen to monitor the position of the beam because of their good low frequency response and high linearity. The need to accelerate low-energy partially-stripped heavy ions requires the pick-up electrodes (PUEs) to operate in a 3 x 10 -11 torr vacuum. The PUEs are to measure the beam position to an absolute accuracy of ±0.5 mm and must therefore be mechanically stable despite the requirements that they be vacuum fired at 950 degree C and baked periodically to 300 degree C. This presentation describes both the mechanical design of the PUEs and the automated test procedure used to ensure the stability, accuracy, and linearity of each unit. 3 refs., 5 figs

  5. Response to booster doses of hepatitis B vaccine among young adults who had received neonatal vaccination.

    Directory of Open Access Journals (Sweden)

    Paul K S Chan

    Full Text Available Newborns who have received hepatitis B immunization in 1980s are now young adults joining healthcare disciplines. The need for booster, pre- and post-booster checks becomes a practical question.The aim of this study is to refine the HBV vaccination policy for newly admitted students in the future.A prospective study on medical and nursing school entrants to evaluate hepatitis B serostatus and the response to booster doses among young adults.Among 212 students, 17-23-year-old, born after adoption of neonatal immunization, 2 (0.9% were HBsAg positive, 40 (18.9% were anti-HBs positive. At 1 month after a single-dose booster for anti-HBs-negative students, 14.5% had anti-HBs 100 mIU/mL, respectively. The anti-HBs levels were significantly higher for females than males (mean [SD]: 431 [418] vs. 246 [339] mIU/mL, P = 0.047. At 2-4 month after the third booster dose, 97.1% had anti-HBs >100 mIU/mL and 2.9% had 10-100 mIU/mL.Pre-booster check is still worthwhile to identify carriers among newly recruited healthcare workers born after adoption of neonatal immunization. A 3-dose booster, rather than a single dose, is required for the majority to achieve an anti-HBs level >100 mIU/mL, as memory immunity has declined in a substantial proportion of individuals. Cost-effectiveness of post-booster check for anti-HBs is low and should be further evaluated based on contextual specific utilization of results.

  6. Pressure-Equalizing Cradle for Booster Rocket Mounting

    Science.gov (United States)

    Rutan, Elbert L. (Inventor)

    2015-01-01

    A launch system and method improve the launch efficiency of a booster rocket and payload. A launch aircraft atop which the booster rocket is mounted in a cradle, is flown or towed to an elevation at which the booster rocket is released. The cradle provides for reduced structural requirements for the booster rocket by including a compressible layer, that may be provided by a plurality of gas or liquid-filled flexible chambers. The compressible layer contacts the booster rocket along most of the length of the booster rocket to distribute applied pressure, nearly eliminating bending loads. Distributing the pressure eliminates point loading conditions and bending moments that would otherwise be generated in the booster rocket structure during carrying. The chambers may be balloons distributed in rows and columns within the cradle or cylindrical chambers extending along a length of the cradle. The cradle may include a manifold communicating gas between chambers.

  7. PS Booster - Festive colloquium

    CERN Multimedia

    2012-01-01

    A festive colloquium will be held to celebrate the 40th anniversary of the PS Booster on Friday, 28 September at 2 p.m. in the CERN council chamber. The meeting will be open to everybody. Read more on the PS Booster in the CERN Bulletin and in the CERN Courier.

  8. AGS booster prototype magnets

    International Nuclear Information System (INIS)

    Danby, G.; Jackson, J.; Lee, Y.Y.; Phillips, R.; Brodowski, J.; Jablonski, E.; Keohane, G.; McDowell, B.; Rodger, E.

    1987-01-01

    Prototype magnets have been designed and constructed for two half cells of the AGS Booster. The lattice requires 2.4m long dipoles, each curved by 10 0 . The multi-use Booster injector requires several very different standard magnet cycles, capable of instantaneous interchange using computer control from dc up to 10 Hz

  9. AGS Booster prototype magnets

    Energy Technology Data Exchange (ETDEWEB)

    Danby, G.; Jackson, J.; Lee, Y.Y.; Phillips, R.; Brodowski, J.; Jablonski, E.; Keohane, G.; McDowell, B.; Rodger, E.

    1987-03-19

    Prototype magnets have been designed and constructed for two half cells of the AGS Booster. The lattice requires 2.4m long dipoles, each curved by 10/sup 0/. The multi-use Booster injector requires several very different standard magnet cycles, capable of instantaneous interchange using computer control from dc up to 10 Hz.

  10. The effect of shaped wheelchair cushion and lumbar supports on under-seat pressure, comfort, and pelvic rotation.

    Science.gov (United States)

    Samuelsson, Kersti; Björk, Maarit; Erdugan, Ann-Marie; Hansson, Anna-Karin; Rustner, Birgitta

    2009-09-01

    A wheelchair seat and position help clients perform daily activities. The comfort of the wheelchair can encourage clients to participate in daily activities and can help prevent future complications. This study evaluates how a shaped seat-cushion and two different back supports affect under-seat pressure, comfort, and pelvic rotation. Thirty healthy subjects were tested using two differently equipped manual wheelchairs. One wheelchair had a Velcro adjustable back seat and a plane seat-cushion. The other wheelchair had a non-adjustable sling-back seat and a plane cushion. The second wheelchair was also equipped with a shaped cushion and/or a detachable lumbar support. Under-seat pressure, estimated comfort, and pelvic rotation were measured after 10 min in each wheelchair outfit. Peak pressure increased with the shaped cushion compared to the plane cushion. No significant difference in estimated comfort was found. Pelvic posterior-rotation was reduced with the adjustable or detachable back-support irrespective of the shape of the seat cushion. To support a neutral pelvic position and spinal curvature, a combination of a shaped cushion and a marked lumbar support is most effective.

  11. Advanced Infant Car Seat Would Increase Highway Safety

    Science.gov (United States)

    Dabney, Richard; Elrod, Susan

    2004-01-01

    the video cameras would be transmitted by radio or infrared to a portable, miniature receiver/video monitor unit that would be attached to the dashboard of the car. The video-camera subsystem can also be used within transmission/reception range when the seat was removed from the car. The system would include a biotelemetric and tracking subsystem, which would include a Global Positioning System receiver for measuring its location. This subsystem would transmit the location of the infant car seat (even if the seat were not in a car) along with such biometric data as the baby s heart rate, perspiration rate, urinary status, temperature, and rate of breathing. Upon detecting any anomalies in the biometric data, this subsystem would send a warning to a paging device installed in the car or carried by the driver, so that the driver could pull the car off the road to attend to the baby. A motion detector in this subsystem would send a warning if the infant car seat were to be moved or otherwise disturbed unexpectedly while the infant was seated in it: this warning function, in combination with the position- tracking function, could help in finding a baby who had been kidnapped with the seat. Removable rechargeable batteries would enable uninterrupted functioning of all parts of the system while transporting the baby to and from the car. The batteries could be recharged via the cigarette-lighter outlet in the car or by use of an external AC-powered charger.

  12. TU-H-CAMPUS-TeP1-02: Seated Treatment: Setup Uncertainty Comparable to Supine

    Energy Technology Data Exchange (ETDEWEB)

    McCarroll, R [UT MD Anderson Cancer Center, Houston, TX (United States); UT Health Science Center, Graduate School of Biomedical Sciences, Houston, TX (United States); Beadle, B; Fullen, D; Balter, P; Followill, D; Stingo, F; Yang, J; Court, L [UT MD Anderson Cancer Center, Houston, TX (United States)

    2016-06-15

    Purpose: For some head and neck patients, positioning in the supine position is not well tolerated. For these patients, treatment in a seated position would be preferred. We have evaluated inter- and intra- fraction uncertainty of patient set-up in a novel treatment chair which is compatible with modern linac designs. Methods: Five head-and-neck cancer patients were positioned in the chair, fitted with immobilization devices, and imaged with orthogonal X-rays. The couch (with chair attached) was rotated to simulate delivery (without actual treatment), another set of images were acquired, providing a measure of intra-fraction displacement. The patient then got off of and back onto the chair and the process was repeated, thus providing a measure of inter-fraction set-up uncertainty. Six sub-regions in the head-and-neck were rigidly registered to evaluate local intra- and interfraction displacement. Image guidance was simulated by first registering one sub-region; the residual displacement of other sub-regions was then measured. Additionally, a patient questionnaire was administered to evaluate tolerance of the seated position. Results: The chair design is such that all advantages of couch motions may be utilized. Average inter- and intrafraction displacements of all sub-regions in the seated position were less than 2 and 3 mm, respectively. When image guidance was simulated, interfraction displacements were reduced by an average of 4 mm, providing comparable setup to the supine position. The enrolled patients, who had no indication for a seated treatment position, reported no preference for the seated or the supine position. Conclusion: The novel chair design provides acceptable inter- and intra-fraction displacement, with reproducibility similar to that observed for patients in the supine position. Such a chair will be utilized for patients who cannot tolerate the supine position and use with CBCT images for planning, in a fixed-beam linac system, and for other

  13. 47 CFR 74.733 - UHF translator signal boosters.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 4 2010-10-01 2010-10-01 false UHF translator signal boosters. 74.733 Section... Translator, and TV Booster Stations § 74.733 UHF translator signal boosters. (a) The licensee of a UHF television broadcast translator station may be authorized to operate one or more signal boosters for the...

  14. Adaptive magnetorheological seat suspension for the expeditionary fighting vehicle

    International Nuclear Information System (INIS)

    Hiemenz, G J; Hu, W; Wereley, N M

    2009-01-01

    The Expeditionary Fighting Vehicle (EFV) is an amphibious vehicle designed to operate through harsh conditions and at much higher speeds than its predecessors. These unique capabilities and broadly varying operational conditions lead to a complex design and human factors scenario for the forward seating positions that cannot be solved using conventional passive seat suspension systems. Injurious shock loads transmitted to the occupants when traversing over water in high sea states and/or at high speeds, as well as harmful shock and vibration transmitted to the occupants when the vehicle is travelling over land, pose a threat to occupant health and significantly limit mission duration. In this study, a semi-active magnetorheological (MR) seat suspension is developed which adapts to broadly varying operational conditions, as well as occupant weight, to provide optimal protection of EFV occupants. It is shown that this MR seat suspension system will reduce the shock and vibration transmitted to the occupant by up to 33% and 65%, respectively, as compared to the existing passive suspension.

  15. Adaptive magnetorheological seat suspension for the expeditionary fighting vehicle

    Energy Technology Data Exchange (ETDEWEB)

    Hiemenz, G J [Techno-Sciences, Inc., 11750 Beltsville Dr. Ste. 300, Beltsville, MD 20705 (United States); Hu, W; Wereley, N M [Aerospace Engineering, University of Maryland, College Park, MD 20712 (United States)], E-mail: greg@technosci.com, E-mail: wereley@umd.edu

    2009-02-01

    The Expeditionary Fighting Vehicle (EFV) is an amphibious vehicle designed to operate through harsh conditions and at much higher speeds than its predecessors. These unique capabilities and broadly varying operational conditions lead to a complex design and human factors scenario for the forward seating positions that cannot be solved using conventional passive seat suspension systems. Injurious shock loads transmitted to the occupants when traversing over water in high sea states and/or at high speeds, as well as harmful shock and vibration transmitted to the occupants when the vehicle is travelling over land, pose a threat to occupant health and significantly limit mission duration. In this study, a semi-active magnetorheological (MR) seat suspension is developed which adapts to broadly varying operational conditions, as well as occupant weight, to provide optimal protection of EFV occupants. It is shown that this MR seat suspension system will reduce the shock and vibration transmitted to the occupant by up to 33% and 65%, respectively, as compared to the existing passive suspension.

  16. Magnetic field errors tolerances of Nuclotron booster

    Science.gov (United States)

    Butenko, Andrey; Kazinova, Olha; Kostromin, Sergey; Mikhaylov, Vladimir; Tuzikov, Alexey; Khodzhibagiyan, Hamlet

    2018-04-01

    Generation of magnetic field in units of booster synchrotron for the NICA project is one of the most important conditions for getting the required parameters and qualitative accelerator operation. Research of linear and nonlinear dynamics of ion beam 197Au31+ in the booster have carried out with MADX program. Analytical estimation of magnetic field errors tolerance and numerical computation of dynamic aperture of booster DFO-magnetic lattice are presented. Closed orbit distortion with random errors of magnetic fields and errors in layout of booster units was evaluated.

  17. Measuring target for the PS Booster

    CERN Multimedia

    1971-01-01

    The measuring target for the PS Booster (originally 800 MeV, now 1.4 GeV). It measures the size of the beam by destroying all particles with amplitudes greater than the size of the fork, the position and width of which are adjustable. The plunging time is only 20 ms and the acceleration at the tip of the fork reaches 90 g. The servo-controlled linear motor is shown detached from the mechanism. See also 7602008.

  18. Beam tests on a proton linac booster for hadron therapy

    CERN Document Server

    De Martinis, C; Berra, P; Birattari, C; Calabretta, L; Crandall, K; Giove, D; Masullo, M R; Mauri, M; Rosso, E; Rovelli, A; Serafini, L; Szeless, Balázs; Toet, D Z; Vaccaro, Vittorio G; Weiss, M; Zennaro, R

    2002-01-01

    LIBO is a 3 GHz modular side-coupled proton linac booster designed to deliver beam energies up to 200 MeV, as required for the therapy of deep seated tumours. The injected beam of 50 to 70 MeV is produced by a cyclotron like those in several hospitals and research institutes. A full-scale prototype of the first module with an input/output energy of 62/74 MeV, respectively, was designed and built in 1999 and 2000. Full power RF tests were carried out successfully at CERN using a test facility at LIL at the end of the year 2000. In order to prove the feasibility of the acceleration process, an experimental setup with this module was installed at the INFN Laboratorio Nazionale del Sud (LNS) in Catania during 2001. The superconducting cyclotron provided the 62 MeV test beam. A compact solid-state RF modulator with a 4 MW klystron, made available by IBA-Scanditronix, was put into operation to power the linac. In this paper the main features of the accelerator are reviewed and the experimental results obtained duri...

  19. Factors related to seatbelt-wearing among rear-seat passengers in Malaysia.

    Science.gov (United States)

    Ng, Choy Peng; Law, Teik Hua; Wong, Shaw Voon; Kulanthayan, S

    2013-01-01

    The benefit of wearing a rear seatbelt in reducing the risk of motor vehicle crash-related fatalities and injuries has been well documented in previous studies. Wearing a seatbelt not only reduces the risk of injury to rear-seat passengers, but also reduces the risk of injury to front-seat occupant who could be crushed by unbelted rear-seat passengers in a motor vehicle crash. Despite the benefits of wearing a rear seatbelt, its rate of use in Malaysia is generally low. The objective of this study was to identify factors that are associated with the wearing of a seatbelt among rear-seat passengers in Malaysia. Multinomial logistic regression analysis of the results of a questionnaire survey of 1651 rear-seat passengers revealed that rear-seat passengers who were younger, male, single and less educated and who had a perception of a low level of legislation enforcement, a lower risk-aversion and less driving experience (only for passengers who are also drivers) were less likely to wear a rear seatbelt. There was also a significant positive correlation between driver seatbelt and rear seatbelt-wearing behaviour. This implies that, in regards to seatbelt-wearing behaviour, drivers are more likely to adopt the same seatbelt-wearing behaviour when travelling as rear-seat passengers as they do when driving. These findings are crucial to the development of new interventions to increase the compliance rate of wearing a rear seatbelt. Copyright © 2012 Elsevier Ltd. All rights reserved.

  20. Physiological Motion Axis for the Seat of a Dynamic Office Chair

    Science.gov (United States)

    Kuster, Roman Peter; Bauer, Christoph Markus; Oetiker, Sarah; Kool, Jan

    2016-01-01

    Objective The aim of this study was to determine and verify the optimal location of the motion axis (MA) for the seat of a dynamic office chair. Background A dynamic seat that supports pelvic motion may improve physical well-being and decrease the risk of sitting-associated disorders. However, office work requires an undisturbed view on the work task, which means a stable position of the upper trunk and head. Current dynamic office chairs do not fulfill this need. Consequently, a dynamic seat was adapted to the physiological kinematics of the human spine. Method Three-dimensional motion tracking in free sitting helped determine the physiological MA of the spine in the frontal plane. Three dynamic seats with physiological, lower, and higher MA were compared in stable upper body posture (thorax inclination) and seat support of pelvic motion (dynamic fitting accuracy). Spinal kinematics during sitting and walking were compared. Results The physiological MA was at the level of the 11th thoracic vertebra, causing minimal thorax inclination and high dynamic fitting accuracy. Spinal motion in active sitting and walking was similar. Conclusion The physiological MA of the seat allows considerable lateral flexion of the spine similar to walking with a stable upper body posture and a high seat support of pelvic motion. Application The physiological MA enables lateral flexion of the spine, similar to walking, without affecting stable upper body posture, thus allowing active sitting while focusing on work. PMID:27150530

  1. AAP Updates Recommendations on Car Seats

    Science.gov (United States)

    ... Size Email Print Share AAP Updates Recommendations on Car Seats Page Content Article Body Children should ride ... of approved car safety seats. Healthy Children Radio: Car Seat Safety Dennis Durbin, MD, FAAP, lead author ...

  2. The PS Booster hits 40

    CERN Multimedia

    Joannah Caborn Wengler

    2012-01-01

    Many accelerators’ "round" birthdays are being celebrated at CERN these days – the PS turned 50 in 2009, the SPS was 35 in 2011, and this year it's the turn of the PS Booster to mark its 40th anniversary. Originally designed to accelerate 1013 protons to 800 MeV, it has far exceeded its initial design performance over the years.   The PS Booster in the 1970s. Imagine the scene: a group of accelerator physicists staring expectantly at a monitor, when suddenly a shout of joy goes up as a signal flickers across the screen. Does that sound familiar? Well, turn the clock back 40 years (longer hair, wider trouser legs) and you have the situation at the PS Booster on 26 May 1972. On that day, beam was injected into the Booster for the first time. “It was a real buzz,” says Heribert Koziol, then Chairman of the Running-in Committee. “We were very happy – and also a little relieved – when the beam finally...

  3. The risk of whiplash-induced medical impairment in rear-end impacts for males and females in driver seat compared to front passenger seat

    Directory of Open Access Journals (Sweden)

    Bertil Jonsson

    2013-07-01

    Females had a relative risk of medical impairment of 3.1 compared to men after adjustment for the average increased risk in the driver position. The driver position had a doubled relative risk compared to the front passenger position. As a conclusion it may be of value to take risk differences between male and female occupants and between driver and front passenger positions into account in future automotive car and seat construction.

  4. Fox-7 for Insensitive Boosters

    Science.gov (United States)

    2010-08-01

    cavitation , and therefore nucleation, to occur at each frequency. As well as producing ultrasound at different frequencies, the method of delivery of...processing techniques using ultrasound , designed to optimise FOX-7 crystal size and morphology to improve booster formulations, and results from these...7 booster formulations. Also included are particle processing techniques using ultrasound , designed to optimise FOX-7 crystal size and morphology

  5. The Booster

    CERN Multimedia

    1972-01-01

    Where the beams from the Booster's four rings begin to recombine, before transfer to the PS. On the left are dipoles for vertical steering, and on the right is the tank containing two septum magnets which form the first combining element.

  6. Reusable Boosters in a European-Russian Perspective

    Science.gov (United States)

    Deneu, François; Ramiandrasoa, Fabienne

    2002-01-01

    In 2001, EADS and Khrunichev SRPSC have initiated and carried out a working group devoted to the analysis of potential common studies and developments in the field of space activities. This working group came up with several propositions of interest, among which, the use of reusable boosters issued from Khrunichev previous design appeared to be promising when applied to heavy type launchers. Although the results required to be confirmed by detailed studies prior to final conclusions, preliminary studies have shown the interest of Ariane 5 configurations using such reusable booster in view of reducing the specific and launch cost as well as potentially increasing the performance. In November 2001, EADS and KHRUNICHEV SRPSC have started a study on an Ariane 5 plus reusable boosters configuration. This study aims at obtaining a better understanding of the advantages and drawbacks attached to such a use. Technical feasibility is more in depth analysed, with all recurring and not recurring aspects (including launch infrastructure modifications). Programmatic aspects are also addressed in order to better assess potential economic advantages and unavoidable drawbacks. Beyond that the identification of what could be, for western Europe and Russian players, an efficient and pay- off industrial organisation, is also a study theme of importance. This papers intends to present the main results achieved within this study and the propositions for the future which are likely to provide western Europe and Russia with stronger positions in the competitive field of launch business.

  7. Roadside observation of child passenger restraint use

    Directory of Open Access Journals (Sweden)

    Beth Bruce

    2015-10-01

    Full Text Available Background: Despite legislation and research evidence supporting the use of childhood vehicle restraints, motor vehicle crashes remain the leading cause of injury, death and disability among Canadian children. Methods: Working in collaboration with trained car seat specialists and police officers, roadside checks were conducted to observe correct use of child restraints. Results: Of the 1323 child vehicle restraints inspected, 99.6% of the children were restrained, 91% were in the correct seat, and 48% of restraints were correctly installed. The seat/restraint types most used incorrectly used were booster seats (31% and seat belts (53%. The majority of incorrectly installed or fitted seats (55% were forward facing. Common errors in installation and fit included the seat not being secured tightly enough to the vehicle, incorrect tether strap use, the harness not being tight enough, and/or the chest clip being in the wrong place. Conclusions: The greatest proportion of incorrect seat use was among those children who transitioned to a seat belt too soon. The greatest proportion of installation and fit errors were among forward facing seats. Researchers recommend: 1 targeting parents with older children (ages 3 and above regarding transitioning too soon from forward facing seats to booster seats, and from booster seats to seat belts; 2 targeting parents with younger children regarding correct installation of rear facing and forward facing seats; 3 collaborating with police officers to review the most common errors and encourage observation at roadside checks; and 4 creating community awareness by way of roadside checks.

  8. Seating position, seat belt wearing, and the consequences in facial fractures in car occupants Posição no veículo, uso de cinto de segurança e suas conseqüências nas fraturas de face em ocupantes de carros

    Directory of Open Access Journals (Sweden)

    Alexandre Siqueira Franco Fonseca

    2007-01-01

    Full Text Available INTRODUCTION: Trauma caused by traffic accidents is among the main etiologies involved in the occurrence of facial fractures throughout the world. However, the trauma mechanisms involved are different according to the location where the study was performed, due to different conditions of development, legislation, and culture. A retrospective study was done between February 2001 and July 2006, with the purpose of determining the epidemiology and the mechanisms involved in the occurrence of facial fractures among car occupants in the metropolitan area of São Paulo. METHODS: Data were collected from 297 patients admitted with facial fractures to the emergency room of the Hospital das Clínicas, São Paulo University Medical School. Within this period, 151 individuals had been involved in traffic accidents, among which 56 (37.08% were inside passenger cars. These were grouped based on the seating position that they were occupying at the time of the accident and the wearing of seat belts. Data concerning the number and location of fracture lines were obtained from the different groups, and a fracture/patient index (F/P I was calculated to compare and make reference to the impact energy among these groups, for subsequent analysis and discussion. RESULTS: 323 fracture lines occurred among 56 patients who were car occupants. By applying the F/P I, we obtained higher values in the group of rear-seat passengers who were not wearing seat belts (7.23 fractures per patient, followed by the group of drivers not wearing seat belts (6.33 fractures per patient, the group of front-seat passengers not wearing seat belts (5.58 fractures per patient, the group of drivers wearing seat belts (5.54 fractures per patient and, finally, the group of front-seat passengers wearing seat belts (4.00 fractures per patient. None of the rear-seat passengers was wearing seat belts. CONCLUSION: The data collected indicate that the driver position shows a high incidence of facial

  9. Development of a method for rating climate seat comfort

    Science.gov (United States)

    Scheffelmeier, M.; Classen, E.

    2017-10-01

    The comfort aspect in the vehicle interior is becoming increasingly important. A high comfort level offers the driver a good and secure feeling and has a strong influence on passive traffic safety. One important part of comfort is the climate aspect, especially the microclimate that emerges between passenger and seat. In this research, different combinations of typical seat materials are used. Fourteen woven and knitted fabrics and eight leathers and its substitutes for the face fabric layer, one foam, one non-woven and one 3D spacer for the plus pad layer and for the support layer three foam types with variations in structure and raw material as well as one rubber hair structure were investigated. To characterise this sample set by thermo-physiological aspects (e.g. water vapour resistance Ret, thermal resistance Rct, buffering capacity of water vapour Fd) regular and modified sweating guarded hotplates were used according to DIN EN ISO 11092. The results of the material characterisation confirm the common knowledge that seat covers out of textiles have better water vapour resistance values than leathers and its substitutes. Subject trials in a driving simulator were executed to rate the subjective sensation while driving in a vehicle seat. With a thermal, sweating Manikin (Newton Type, Thermetrics) objective product measurements were carried out on the same seat. Indeed the subject trials show that every test subject has his or her own subjective perception concerning the climate comfort. The results of the subject trials offered the parameters for the Newton measuring method. Respectively the sweating rate, sit-in procedure, ambient conditions and sensor positions on and between the seat layers must be comparable with the subject trials. By taking care of all these parameters it is possible to get repeatable and reliable results with the Newton Manikin. The subjective feelings of the test subjects, concerning the microclimate between seat and passenger, provide

  10. Fire resistant aircraft seat materials

    Science.gov (United States)

    Trabold, E. L.

    1978-01-01

    The establishment of a technical data base for individual seat materials in order to facilitate materials selections is reviewed. The thermal response of multi-layer constructions representative of the basic functional layers of a typical future seat is examined. These functional layers include: (1) decorative fabric cover; (2) slip sheet (topper); (3) fire blocking layer; (4) cushion reinforcement; and (5) cushioning layer. The implications for material selection for full-scale seats are discussed.

  11. Summary of Booster Development and Qualification Report

    Energy Technology Data Exchange (ETDEWEB)

    Francois, Elizabeth G. [Los Alamos National Laboratory; Harry, Herbert H. [Los Alamos National Laboratory; Hartline, Ernest L. [Los Alamos National Laboratory; Hooks, Daniel E. [Los Alamos National Laboratory; Johnson, Carl E. [Los Alamos National Laboratory; Morris, John S. [Los Alamos National Laboratory; Novak, Alan M. [Los Alamos National Laboratory; Ramos, Kyle J. [Los Alamos National Laboratory; Sanders, Victor E. [Los Alamos National Laboratory; Scovel, Christina A. [Los Alamos National Laboratory; Lorenz, Thomas [LLNL; Wright, Mark [AWE; Botcher, Tod [PANTEX; Marx, Erin [NSWC-IHDIV; Gibson, Kevin [NSWC-IHDIV

    2012-06-21

    This report outlines booster development work done at Los Alamos National Laboratory from 2007 to present. The booster is a critical link in the initiation train of explosive assemblies, from complex devices like nuclear weapons to conventional munitions. The booster bridges the gap from a small, relatively sensitive detonator to an insensitive, but massive, main charge. The movement throughout the explosives development community is to use more and more insensitive explosive components. With that, more energy is needed out of the booster. It has to initiate reliably, promptly, powerfully and safely. This report is divided into four sections. The first provides a summary of a collaborative effort between LANL, LLNL, and AWE to identify candidate materials and uniformly develop a testing plan for new boosters. Important parameters and the tests required to measure them were defined. The nature of the collaboration and the specific goals of the participating partners has changed over time, but the booster development plan stands on its own merit as a complete description of the test protocol necessary to compare and qualify booster materials, and is discussed in its entirety in this report. The second section describes a project, which began in 2009 with the Department of Defense to develop replacement booster formulations for PBXN-7. Replacement of PBXN-7 was necessary because it contained Triaminotrinitrobenzene (TATB), which was becoming unavailable to the DoD and because it contained Cyclotrimethylenetrinitramine (RDX), which was sensitive and toxic. A LANL-developed explosive, Diaminoazoxyfurazan (DAAF), was an important candidate. This project required any replacement formulation be a drop-in replacement in existing munitions. This project was timely, in that it made use of the collaborative booster development project, and had the additional constraint of matching shock sensitivity. Additionally it needed to be a safety improvement, and a performance

  12. 30 CFR 57.8518 - Main and booster fans.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Main and booster fans. 57.8518 Section 57.8518... and Underground § 57.8518 Main and booster fans. (a) All mine main and booster fans installed and used...-cycle shutdowns or planned or scheduled fan maintenance or fan adjustments where air quality is...

  13. Improvement of seawater booster pump outlet check valve

    International Nuclear Information System (INIS)

    Li Xuning; Du Yansong; Huang Huimin

    2010-01-01

    Conventional island seawater booster pump set of QNPC 310 MWe unit are very important in the whole circulating cooling system, and the integrate function of seawater booster pump outlet check valve is the foundation of steady operation of the seawater booster pump set. The article mainly introduce that through the analyses to the reason to the problem that the seawater booster pump outlet check valve of QNPC 310 MWe unit appeared in past years by our team, and considering the influence of operation condition and circumstance, the team improve the seawater booster pump outlet check valve from swing check valve to shuttle check valve which operate more appropriately in the system. By the test of continuous practice, we make further modification to the inner structure of shuttle check valve contrapuntally, and therefore we solve the problem in seawater booster pump outlet check valve fundamentally which has troubled the security of system operation in past years, so we realize the aim of technical improvement and ensure that the system operate in safety and stability. (authors)

  14. Conceptual design report: superconducting booster

    International Nuclear Information System (INIS)

    1983-01-01

    The Superconducting Booster project includes the construction of a new high-voltage injector and buncher for the existing tandem, a magnetic transport system, an rf linac with superconducting resonators, and a rebuncher-debuncher. The booster will fit in existing space so that a new building is not required. The layout of the accelerator is given in Fig. I-1. The University of Washington is contributing approximately $1 M to this project

  15. Thermodynamic investigation of a booster-assisted ejector refrigeration system

    International Nuclear Information System (INIS)

    Zhao, Hongxia; Zhang, Ke; Wang, Lei; Han, Jitian

    2016-01-01

    Highlights: • COP based on thermal input increases with booster outlet pressure. • Both entrainment ratio and area ratio increase with booster outlet pressure. • COP based on work is larger than compressor-based refrigeration system. • An optimum booster outlet pressure obtains maximum COP based on work. • Exergy destruction occurs mainly in ejector, condenser, evaporator and generator. - Abstract: In order to improve performance of ejector refrigeration system, a booster is added before an ejector to enhance secondary flow pressure, which is called a booster assisted refrigeration system. Based on mass, momentum and energy conservation, a 1D model of ejector for optimal performance prediction was presented and validated with experimental data. A detailed study of working characteristics of the booster assisted ejector refrigeration system was carried out and compared against conventional ejector refrigeration system and compressor based refrigeration system, on the basis of first and second laws of thermodynamics. Effects of booster outlet pressure on COP_t_h based on thermal energy and COP_w based on work input, and also on entrainment ratio and area ratio of ejector were studied. The exergy destruction rates were also computed and analyzed for components of the booster-assisted ejector refrigeration system. Ways to reduce exergy destruction were discussed.

  16. Application of a bus seat buffer to mitigate frontal crash effects

    Science.gov (United States)

    Stanisławek, Sebastian; Dziewulski, Paweł; Sławiński, Grzegorz

    2018-01-01

    The paper considers the problem of coach occupant safety during crash events. The authors present a simple low-cost seat buffer concept which may mitigate the effects of frontal impact. The method of computer simulation was chosen to solve the problem efficiently. The Finite Element Method (FEM) implemented in the LS-DYNA commercial code was used. The testing procedure was based on European Commission regulations, under which vehicles move at a defined speed. Simulations have shown that seat occupants suffer serious trauma during a crash, with the head experiencing relatively high acceleration, thus resulting in an HIC36 of 1490. The installation of a protective buffer mounted on the upper part of the seat reduced the HIC36 to only 510. However, in its current form it does not meet the requirements of the regulations. Further modifications to the overlay shape and structure are essential in order to better improve the deceleration of passengers' bodies. Moreover, a detailed model of seats and their anchorage should be taken into account. A more flexible structure should provide more positive and more accurate results.

  17. Gas Test Loop Booster Fuel Hydraulic Testing

    International Nuclear Information System (INIS)

    Gas Test Loop Hydraulic Testing Staff

    2006-01-01

    The Gas Test Loop (GTL) project is for the design of an adaptation to the Advanced Test Reactor (ATR) to create a fast-flux test space where fuels and materials for advanced reactor concepts can undergo irradiation testing. Incident to that design, it was found necessary to make use of special booster fuel to enhance the neutron flux in the reactor lobe in which the Gas Test Loop will be installed. Because the booster fuel is of a different composition and configuration from standard ATR fuel, it is necessary to qualify the booster fuel for use in the ATR. Part of that qualification is the determination that required thermal hydraulic criteria will be met under routine operation and under selected accident scenarios. The Hydraulic Testing task in the GTL project facilitates that determination by measuring flow coefficients (pressure drops) over various regions of the booster fuel over a range of primary coolant flow rates. A high-fidelity model of the NW lobe of the ATR with associated flow baffle, in-pile-tube, and below-core flow channels was designed, constructed and located in the Idaho State University Thermal Fluids Laboratory. A circulation loop was designed and constructed by the university to provide reactor-relevant water flow rates to the test system. Models of the four booster fuel elements required for GTL operation were fabricated from aluminum (no uranium or means of heating) and placed in the flow channel. One of these was instrumented with Pitot tubes to measure flow velocities in the channels between the three booster fuel plates and between the innermost and outermost plates and the side walls of the flow annulus. Flow coefficients in the range of 4 to 6.5 were determined from the measurements made for the upper and middle parts of the booster fuel elements. The flow coefficient for the lower end of the booster fuel and the sub-core flow channel was lower at 2.3

  18. Gas Test Loop Booster Fuel Hydraulic Testing

    Energy Technology Data Exchange (ETDEWEB)

    Gas Test Loop Hydraulic Testing Staff

    2006-09-01

    The Gas Test Loop (GTL) project is for the design of an adaptation to the Advanced Test Reactor (ATR) to create a fast-flux test space where fuels and materials for advanced reactor concepts can undergo irradiation testing. Incident to that design, it was found necessary to make use of special booster fuel to enhance the neutron flux in the reactor lobe in which the Gas Test Loop will be installed. Because the booster fuel is of a different composition and configuration from standard ATR fuel, it is necessary to qualify the booster fuel for use in the ATR. Part of that qualification is the determination that required thermal hydraulic criteria will be met under routine operation and under selected accident scenarios. The Hydraulic Testing task in the GTL project facilitates that determination by measuring flow coefficients (pressure drops) over various regions of the booster fuel over a range of primary coolant flow rates. A high-fidelity model of the NW lobe of the ATR with associated flow baffle, in-pile-tube, and below-core flow channels was designed, constructed and located in the Idaho State University Thermal Fluids Laboratory. A circulation loop was designed and constructed by the university to provide reactor-relevant water flow rates to the test system. Models of the four booster fuel elements required for GTL operation were fabricated from aluminum (no uranium or means of heating) and placed in the flow channel. One of these was instrumented with Pitot tubes to measure flow velocities in the channels between the three booster fuel plates and between the innermost and outermost plates and the side walls of the flow annulus. Flow coefficients in the range of 4 to 6.5 were determined from the measurements made for the upper and middle parts of the booster fuel elements. The flow coefficient for the lower end of the booster fuel and the sub-core flow channel was lower at 2.3.

  19. Modeling the Impact of Space Suit Components and Anthropometry on the Center of Mass of a Seated Crewmember

    Science.gov (United States)

    Rajulu, Sudhakar; Blackledge, Christopher; Ferrer, Mike; Margerum, Sarah

    2009-01-01

    The designers of the Orion Crew Exploration Vehicle (CEV) utilize an intensive simulation program in order to predict the launch and landing characteristics of the Crew Impact Attenuation System (CIAS). The CIAS is the energy absorbing strut concept that dampens loads to levels sustainable by the crew during landing and consists of the crew module seat pallet that accommodates four to six seated astronauts. An important parameter required for proper dynamic modeling of the CIAS is knowledge of the suited center of mass (COM) variations within the crew population. Significant center of mass variations across suited crew configurations would amplify the inertial effects of the pallet and potentially create unacceptable crew loading during launch and landing. Established suited, whole-body, and posture-based mass properties were not available due to the uncertainty of the final CEV seat posture and suit hardware configurations. While unsuited segmental center of mass values can be obtained via regression equations from previous studies, building them into a model that was posture dependent with custom anthropometry and integrated suit components proved cumbersome and time consuming. Therefore, the objective of this study was to quantify the effects of posture, suit components, and the expected range of anthropometry on the center of mass of a seated individual. Several elements are required for the COM calculation of a suited human in a seated position: anthropometry; body segment mass; suit component mass; suit component location relative to the body; and joint angles defining the seated posture. Anthropometry and body segment masses used in this study were taken from a selection of three-dimensional human body models, called boundary manikins, which were developed in a previous project. These boundary manikins represent the critical anthropometric dimension extremes for the anticipated astronaut population. Six male manikins and 6 female manikins, representing a

  20. A Motion Control of a Robotic Walker for Continuous Assistance during Standing, Walking and Seating Operation

    OpenAIRE

    Chugo, Daisuke; Takase, Kunikatsu

    2010-01-01

    In this paper, we develop an active walker system for standing, walking and seating operation continuously which cooperates the developed standing assistance system with safety and stability. For realizing these conditions, our walker coordinates the assisting position cooperating the standing assistance manipulator according to the posture of the patient. Furthermore, our walker adjusts a seating position when the patient sit down which has high risk for falling down. Using our proposed syst...

  1. Muscle Power during Standing and Seated Trunk Rotations with Different Weights

    Directory of Open Access Journals (Sweden)

    Erika Zemková

    2017-10-01

    Full Text Available This study compares peak and mean power during standing and seated trunk rotations with different weights. Twenty seven fit men completed four trials of trunk rotations in both standing and seated positions with a bar weight of 5.5, 10.5, 15.5, and 20 kg placed on the shoulders. The FiTRO Torso Premium was used to monitor basic biomechanical parameters throughout the movement. Results showed significantly higher peak power during standing than seated trunk rotations at weights of 20 kg (274.4±63.5 vs. 206.4±54.6 W, p=0.004, 15.5 kg (371.2±93.9 vs. 313.5±72.3 W, p=0.007, and 10.5 kg (336.9±77.8 vs. 286.3±66.0 W, p=0.009 but not at 5.5 kg (191.6±46.2 vs. 166.0±37.0 W, p=0.061. Similarly, mean power in the acceleration phase of trunk rotations was significantly higher when performed in standing than seated position at weights of 20 kg (143.2±32.1 vs. 101.9±23.7 W, p=0.008, 15.5 kg (185.1±42.3 vs. 150.4±36.5 W, p=0.019, and 10.5 kg (169.8±40.7 vs. 139.7±31.6 W, p=0.024 but not at 5.5 kg (107.4±29.4 vs. 86.5±21.1 W, p=0.111. Furthermore, peak and mean power during standing trunk rotations significantly correlated with values achieved in the seated position at the weight of 5.5 kg (r=0.684, p=0.027; r=0.676, p=0.033 but not at 10.5 kg (r=0.589, p=0.089; r=0.552, p=0.143, 15.5 kg (r=0.493, p=0.243; r=0.436, p=0.298, and 20 kg (r=0.357, p=0.361; r=0.333, p=0.417. In conclusion, power production is greater during standing as compared to seated trunk rotations, with more pronounced differences at higher weights. This fact has to be taken into account when training and testing the trunk rotational power.

  2. Design of the Zero Gradient Synchrotron Booster-II lattice

    International Nuclear Information System (INIS)

    Crosbie, E.A.; Foss, M.H.; Khoe, T.K.; Simpson, J.D.

    1975-01-01

    A 500 MeV booster was designed at the Argonne National Laboratory to increase the beam intensity from the Zero Gradient Synchrotron (ZGS). Many turns of H - ions from the 50 MeV linac will be injected into the booster and stripped to H + so that the ring will contain the maximum useful charge in each booster pulse. Several booster pulses will be injected into the ZGS to form one ZGS pulse. This machine is now under construction. (auth)

  3. Child Passenger Safety (A Minute of Health with CDC)

    Centers for Disease Control (CDC) Podcasts

    Using the correct car seat for your child can be a lifesaver. This podcast discusses the importance of ensuring children are buckled up in car seats or booster seats that are appropriate for their age and size until adult seat belts fit properly.

  4. Simulation of a programmed frequency shift near extraction from the Fermilab Booster

    International Nuclear Information System (INIS)

    Lucas, P.; Kerns, Q.

    1987-03-01

    The longitudinal phase space program ESME has been used to simulate the effects of a linear shift in RF frequency away from that appropriate for the accelerator guide field. This shift takes place in the new Booster low level RF and is used to position the particle bunches in Main Ring buckets in a reproducible fashion. Shifts in frequency are found to generate synchrotron oscillations; however, the simulations show that these can be reduced to acceptable levels by introduction of jumps in RF phase preceding the programmed frequency changes. Lowering the RF voltage near extraction from the Booster, a desirable operational feature, has also been investigated

  5. Drive alive: teen seat belt survey program.

    Science.gov (United States)

    Burkett, Katie M; Davidson, Steve; Cotton, Carol; Barlament, James; Loftin, Laurel; Stephens, James; Dunbar, Martin; Butterfield, Ryan

    2010-08-01

    To increase teen seat belt use among drivers at a rural high school by implementing the Drive Alive Pilot Program (DAPP), a theory-driven intervention built on highway safety best practices. The first component of the program was 20 observational teen seat belt surveys conducted by volunteer students in a high school parking lot over a 38-month period before and after the month-long intervention. The survey results were published in the newspaper. The second component was the use of incentives, such as gift cards, to promote teen seat belt use. The third component involved disincentives, such as increased police patrol and school policies. The fourth component was a programmatic intervention that focused on education and media coverage of the DAPP program. Eleven pre-intervention surveys and nine post-intervention surveys were conducted before and after the intervention. The pre- and post-intervention seat belt usage showed significant differences (p<0.0001). The average pre-intervention seat belt usage rate was 51.2%, while the average post-intervention rate was 74.5%. This represents a percentage point increase of 23.3 in seat belt use after the DAPP intervention. Based on seat belt observational surveys, the DAPP was effective in increasing seat belt use among rural high school teenagers. Utilizing a theory-based program that builds on existing best practices can increase the observed seat belt usage among rural high school students.

  6. Fire resistant aircraft seat program

    Science.gov (United States)

    Fewell, L. A.

    1979-01-01

    Foams, textiles, and thermoformable plastics were tested to determine which materials were fire retardant, and safe for aircraft passenger seats. Seat components investigated were the decorative fabric cover, slip covers, fire blocking layer, cushion reinforcement, and the cushioning layer.

  7. Suppression of transverse instabilities by fast feedback in the Fermilab booster

    International Nuclear Information System (INIS)

    Ankenbrandt, C.; Higgins, E.F. Jr.; Johnson, R.P.

    1977-01-01

    Systems to damp radial and vertical instabilities of individual rf bunches in the Fermilab Booster are being implemented. The positions of individual bunches are derived from stripline pickups. The position information is transmitted over a variable delay, amplified, and applied to deflectors after one almost complete revolution, 6.25 horizontal and 6.75 vertical betatron wavelengths downstream of the pickup. Motivation, system concepts, design considerations, and initial operating experience are described

  8. Validation of seat-off and seat-on in repeated sit-to-stand movements using a single-body-fixed sensor

    International Nuclear Information System (INIS)

    Van Lummel, R C; Ainsworth, E; Hausdorff, J M; Lindemann, U; Beek, P J; Van Dieën, J H

    2012-01-01

    The identification of chair rise phases is a prerequisite for quantifying sit-to-stand movements. The aim of this study is to validate seat-off and seat-on detection using a single-body-fixed sensor against detection based on chair switches. A single sensor system with three accelerometers and three gyroscopes was fixed around the waist. Synchronized on–off switches were placed under the chair. Thirteen older adults were recruited from a residential care home and fifteen young adults were recruited among college students. Subjects were asked to complete two sets of five trials each. Six features of the trunk movement during seat-off and seat-on were calculated automatically, and a model was developed to predict the moment of seat-off and seat-on transitions. The predictions were validated with leave-one-out cross-validation. Feature extraction failed in two trials (0.7%). For the optimal combination of seat-off predictors, cross-validation yielded a mean error of 0 ms and a mean absolute error of 51 ms. For the best seat-on predictor, cross-validation yielded a mean error of –3 ms and a mean absolute error of 127 ms. The results of this study demonstrate that seat-off and seat-on in repeated sit-to-stand movements can be detected semi-automatically in young and older adults using a one-body-fixed sensor system with an accuracy of 51 and 127 ms, respectively. The use of the ambulatory instrumentation is feasible for non-technically trained personnel. This is an important step in the development of an automated method for the quantification of sit-to-stand movements in clinical practice. (paper)

  9. NASA Standards Inform Comfortable Car Seats

    Science.gov (United States)

    2014-01-01

    NASA developed standards, which included the neutral body posture (NBP), to specify ways to design flight systems that support human health and safety. Nissan Motor Company, with US offices in Franklin, Tennessee, turned to NASA's NBP research for the development of a new driver's seat. The 2013 Altima now features the new seat, and the company plans to incorporate the seats in upcoming vehicles.

  10. The Sit & Stand chair. A revolutionary advance in adaptive seating systems.

    Science.gov (United States)

    Galumbeck, Michael H; Buschbacher, Ralph M; Wilder, Robert P; Winters, Kathryne L; Hudson, Mary Anne; Edlich, Richard F

    2004-01-01

    A major factor governing independence for the elderly and persons with disabilities is the ability to stand from a chair. Factors such as pain, reduced joint range of motion, stiffness, and muscle weakness frequently limit the ability to stand. Sit-to-stand position is even further reduced in patients whose hands and shoulders are afflicted with rheumatoid arthritis. When achieving a sit-to-stand position in the elderly and persons with disabilities, there is considerable risk of the individual falling and sustaining bone fracture. The purposes of this scientific report are to achieve the following goals: (1) to provide a narrative discussion of the senior author's contributions to furniture manufacturing as well as his successful patent application for the SIT & STAND chair, (2) to describe the steps involved in the development of the SIT & STAND prototype, and (3) to examine the performance of the SIT & STAND chair in assisting the elderly or persons with disabilities in achieving a sit-to-stand position. The invention of the SIT & STAND chair by the senior author, Michael Galumbeck, was a culmination of his lifelong interest in adaptive seating systems. His electrically operated chair has the unique ability to assist the occupant to achieve safely a sit-to-stand position. The rear portion of his chair remains in a fixed position to support the buttocks of the user during mechanical lift. The front portion of the seat folds down incrementally as the chair rises to allow the feet of the user to be positioned in a more posterior position firmly on the floor. Using its actuator, the height that the chair rises will vary with the length of the legs of the occupant. Using the drawing program Solid Works (Solid Works, Concord, Massachusetts), drawings of the chair were made. To visualize the operation and performance of the chair, separate drawings were made in the lateral position. The prototype of the SIT & STAND chair was manufactured with an electric actuator that

  11. Developing the World's Most Powerful Solid Booster

    Science.gov (United States)

    Priskos, Alex S.; Frame, Kyle L.

    2016-01-01

    NASA's Journey to Mars has begun. Indicative of that challenge, this will be a multi-decadal effort requiring the development of technology, operational capability, and experience. The first steps are underway with more than 15 years of continuous human operations aboard the International Space Station (ISS) and development of commercial cargo and crew transportation capabilities. NASA is making progress on the transportation required for deep space exploration - the Orion crew spacecraft and the Space Launch System (SLS) heavy-lift rocket that will launch Orion and large components such as in-space stages, habitat modules, landers, and other hardware necessary for deep-space operations. SLS is a key enabling capability and is designed to evolve with mission requirements. The initial configuration of SLS - Block 1 - will be capable of launching more than 70 metric tons (t) of payload into low Earth orbit, greater mass than any other launch vehicle in existence. By enhancing the propulsion elements and larger payload fairings, future SLS variants will launch 130 t into space, an unprecedented capability that simplifies hardware design and in-space operations, reduces travel times, and enhances two solid propellant five-segment boosters, both based on space shuttle technologies. This paper will focus on development of the booster, which will provide more than 75 percent of total vehicle thrust at liftoff. Each booster is more than 17 stories tall, 3.6 meters (m) in diameter and weighs 725,000 kilograms (kg). While the SLS booster appears similar to the shuttle booster, it incorporates several changes. The additional propellant segment provides additional booster performance. Parachutes and other hardware associated with recovery operations have been deleted and the booster designated as expendable for affordability reasons. The new motor incorporates new avionics, new propellant grain, asbestos-free case insulation, a redesigned nozzle, streamlined manufacturing

  12. Drive Alive: Teen Seat Belt Survey Program

    Directory of Open Access Journals (Sweden)

    Loftin, Laurel

    2010-08-01

    Full Text Available Objective: To increase teen seat belt use among drivers at a rural high school by implementing the Drive Alive Pilot Program (DAPP, a theory-driven intervention built on highway safety best practices.Methods: The first component of the program was 20 observational teen seat belt surveys conducted by volunteer students in a high school parking lot over a 38-month period before and after the month-long intervention. The survey results were published in the newspaper. The second component was the use of incentives, such as gift cards, to promote teen seat belt use. The third component involved disincentives, such as increased police patrol and school policies. The fourth component was a programmatic intervention that focused on education and media coverage of the DAPP program.Results: Eleven pre-intervention surveys and nine post-intervention surveys were conducted before and after the intervention. The pre- and post-intervention seat belt usage showed significant differences (p<0.0001. The average pre-intervention seat belt usage rate was 51.2%, while the average post-intervention rate was 74.5%. This represents a percentage point increase of 23.3 in seat belt use after the DAPP intervention.Conclusion: Based on seat belt observational surveys, the DAPP was effective in increasing seat belt use among rural high school teenagers. Utilizing a theory-based program that builds on existing best practices can increase the observed seat belt usage among rural high school students. [West J Emerg Med. 2010; 11(3: 280-283.

  13. Simulations Of Transverse Stacking In The NSLS-II Booster

    International Nuclear Information System (INIS)

    Fliller, R. III; Shaftan, T.

    2011-01-01

    The NSLS-II injection system consists of a 200 MeV linac and a 3 GeV booster. The linac needs to deliver 15 nC in 80 - 150 bunches to the booster every minute to achieve current stability goals in the storage ring. This is a very stringent requirement that has not been demonstrated at an operating light source. We have developed a scheme to transversely stack two bunch trains in the NSLS-II booster in order to alleviate the charge requirements on the linac. This scheme has been outlined previously. In this paper we show particle tracking simulations of the tracking scheme. We show simulations of the booster ramp with a stacked beam for a variety of lattice errors and injected beam parameters. In all cases the performance of the proposed stacking method is sufficient to reduce the required charge from the linac. For this reason the injection system of the NSLS-II booster is being designed to include this feature. The NSLS-II injection system consists of a 200 MeV linac and a 3 GeV booster. The injectors must provide 7.5nC in bunch trains 80-150 bunches long every minute for top off operation of the storage ring. Top off then requires that the linac deliver 15nC of charge once losses in the injector chain are taken into consideration. This is a very stringent requirement that has not been demonstrated at an operating light source. For this reason we have developed a method to transversely stack two bunch trains in the booster while maintaining the charge transport efficiency. This stacking scheme has been discussed previously. In this paper we show the simulations of the booster ramp with a single bunch train in the booster. Then we give a brief overview of the stacking scheme. Following, we show the results of stacking two bunch trains in the booster with varying beam emittances and train separations. The behavior of the beam through the ramp is examined showing that it is possible to stack two bunch trains in the booster.

  14. 47 CFR 74.1233 - Processing FM translator and booster station applications.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 4 2010-10-01 2010-10-01 false Processing FM translator and booster station... SERVICES FM Broadcast Translator Stations and FM Broadcast Booster Stations § 74.1233 Processing FM translator and booster station applications. (a) Applications for FM translator and booster stations are...

  15. Superconducting racetrack booster for the ion complex of MEIC

    Energy Technology Data Exchange (ETDEWEB)

    Filatov, Yu [Joint Inst. for Nuclear Research (JINR), Dubna (Russian Federation); Moscow Inst. of Physics and Technology (MIPT), Moscow (Russian Federation); Kondratenko, A. M. [Science and Technique Laboratory ' Zaryad' , 630090, Novosibirsk, Russia; Kondratenko, M. A. [Science and Technique Laboratory ' Zaryad' , 630090, Novosibirsk, Russia; Kovalenko, A. [Joint Inst. for Nuclear Research (JINR), Dubna (Russian Federation); Derbenev, Yaroslav S. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Lin, Fanglei [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Morozov, Vasiliy S. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Zhang, Yuhong [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States)

    2016-02-01

    The current design of the Medium-energy Electron-Ion Collider (MEIC) project at Jefferson lab features a single 8 GeV/c figure-8 booster based on super-ferric magnets. Reducing the circumference of the booster by switching to a racetrack design may improve its performance by limiting the space charge effect and lower its cost. We consider problems of preserving proton and deuteron polarizations in a superconducting racetrack booster. We show that using magnets based on hollow high-current NbTi composite superconducting cable similar to those designed at JINR for the Nuclotron guarantees preservation of the ion polarization in a racetrack booster up to 8 GeV/c. The booster operation cycle would be a few seconds that would improve the operating efficiency of the MEIC ion complex.

  16. Object-oriented programming techniques for the AGS Booster

    International Nuclear Information System (INIS)

    Skelly, J.F.

    1991-01-01

    The applications software developed for the control system of the AGS Booster Project was written in the object-oriented language, C++. A the start of the Booster Project, the programming staff of the AGS Controls Section comprised some dozen programmer/analysts, all highly fluent in C but novices in C++. During the coarse of this project, nearly the entire staff converted to using C++ for a large fraction of their assignments. Over 100 C++ software modules are now available for Booster and general AGS use, of which a large fraction are broadly applicable tools. The transition from C to C++ from a managerial perspective is discussed and an overview is provided of the ways in which object classes have been applied in Booster software development

  17. Object-oriented programming techniques for the AGS Booster

    International Nuclear Information System (INIS)

    Skelly, J.F.

    1992-01-01

    The applications software developed for the control system of the AGS Booster Project was written in the object-oriented language, C++. At the start of the Booster Project, the programming staff of the AGS Controls Section comprised some dozen programmer/analysts, all highly fluent in C but novices in C++. During the course of this project, nearly the entire staff converted to using C++ for a large fraction of their assignments. Over 100 C++ software modules are now available both for Booster and general AGS use, of which a large fraction are broadly applicable tools. The transition from C to C++ from a managerial perspective is discussed and an overview is provided of the ways in which object classes have been applied in Booster software development. (author)

  18. Concentrated Ground Plane Booster Antenna Technology for Multiband Operation in Handset Devices

    Directory of Open Access Journals (Sweden)

    C. Picher

    2014-12-01

    Full Text Available The current demand in the handset antenna field requires multiband antennas due to the existence of multiple communication standards and the emergence of new ones. At the same time, antennas with reduced dimensions are strongly required in order to be easily integrated. In this sense, the paper proposes a compact radiating system that uses two non-resonant elements to properly excite the ground plane to solve the abovementioned shortcomings by minimizing the required Printed Circuit Board (PCB area while ensuring a multiband performance. These non-resonant elements are called here ground plane boosters since they excite an efficient mode of the ground plane. The proposed radiating system comprises two ground plane boosters of small dimensions of 5 mm x 5 mm x 5 mm. One is in charge of the low frequency region (0.824-0.960 GHz and the other is in charge of the high frequency region (1.710-2.170 GHz. With the aim of achieving a compact configuration, the two boosters are placed close to each other in a corner of the ground plane of a handset device (concentrated architecture. Several experiments related to the coupling between boosters have been carried out in two different platforms (barphone and smartphone, and the best position and the required matching network are presented. The novel proposal achieves multiband performance at GSM850/900/1800/1900 and UMTS.

  19. LS1 Report: first beams in the Booster

    CERN Multimedia

    Anaïs Schaeffer

    2014-01-01

    On Monday, 2 June, the Operations Group injected the first beams into the PS Booster (PSB). The PSB, the second machine in the LHC injector chain to be recommissioned (Linac2 was the first), also provides beams for non-LHC experiments, some of which will need beams for physics as early as this summer.   The PS Booster. The Operations Group has been back in control of the PS Booster for a month now, having taken over where the engineers and experts of the EN Department, who were responsible for the maintenance work, left off. The group first ran tests with no beam (known as “cold check-out”) to check and requalify all the machine instrumentation, from the control room to the ring itself. Now in beam mode, the Booster is being prepared both to begin supplying the PS at the end of June and, above all, for physics to restart in the ISOLDE experimental area. The PS Booster console in the CERN Control Centre. “We have around 15 types of beams to ‘prepa...

  20. LS1 Report: PS Booster prepares for beam

    CERN Multimedia

    Katarina Anthony

    2014-01-01

    With Linac2 already up and running, the countdown to beam in the LHC has begun! The next in line is the PS Booster, which will close up shop to engineers early next week. The injector will be handed over to the Operations Group who are tasked with getting it ready for active duty.   Taken as we approach the end of LS1 activities, this image shows where protons will soon be injected from Linac2 into the four PS Booster rings. Over the coming two months, the Operations Group will be putting the Booster's new elements through their paces. "Because of the wide range of upgrades and repairs carried out in the Booster, we have a very full schedule of tests planned for the machine," says Bettina Mikulec, PS Booster Engineer in Charge. "We will begin with cold checks; these are a wide range of tests carried out without beam, including system tests with power on/off and with varying settings, as well as verification of the controls system and timings." Amon...

  1. Effectiveness of media and enforcement campaigns in increasing seat belt usage rates in a state with a secondary seat belt law.

    Science.gov (United States)

    Vasudevan, Vinod; Nambisan, Shashi S; Singh, Ashok K; Pearl, Traci

    2009-08-01

    In 2005, in terms of seat belt usage rates, Nevada ranked third nationally and first among states with secondary seat belt use enforcement laws in the United States. An effective combination of a media-based education and enforcement campaign helped in this regard. The objective of this article is to document the effectiveness of enforcement and media-based education and outreach campaigns on the seat belt usage rates in Nevada, a state with a secondary seat belt usage law. Observational data on seat belt usage and passenger fatality data are used to evaluate the effectiveness of enforcement campaigns and media-based education and outreach campaigns. Data based on observations of about 40,000 vehicles in each of the years 2003 to 2005 were analyzed. Statistical analyses show that a significant increase in seat belt usage rates among both drivers and passengers for both genders resulted from the accompanying the media and enforcement campaigns. The results from this study indicate that effective and well-planned media/enforcement campaigns can have a significant impact on seat belt usage rates even in a state where the enforcement of seat belt laws can only be as a secondary violation. They validate and expand on findings from other efforts documented in the literature. These results demonstrate that, if coordinated properly, media and enforcement campaigns work very effectively in increasing seat belt usage rates even in states with secondary seat belt laws.

  2. Maintaining the potential of a psycho-educational program: efficacy of a booster session after an intervention offered family caregivers at disclosure of a relative's dementia diagnosis.

    Science.gov (United States)

    Ducharme, Francine; Lachance, Lise; Lévesque, Louise; Zarit, Steven Howard; Kergoat, Marie-Jeanne

    2015-01-01

    Booster sessions as a means of maintaining the benefits of psycho-educational programs have received little attention in caregiving research. Caregivers were offered a booster session following participation in a program entitled Learning to Become a Family Caregiver (LBFC) intended to facilitate transition to the caregiver role after diagnostic disclosure of dementia in a relative. The 90-minute booster session served to review program content and afforded the opportunity to discuss and practice learned skills. This study sought to test the efficacy of the booster session in maintaining or recovering program effects at six months post-program. Participants in the program were randomly assigned to a group that received the booster session (n = 31) or a group that did not (n = 29). A third control group was also formed, which continued to receive only the usual care provided in memory clinics. Eligible participants - French-speaking primary caregivers of a relative diagnosed with Alzheimer's in the past nine months - were recruited in memory clinics in Quebec (Canada). Participants were blindly assessed before randomization and six months after the booster session on outcomes associated with a healthy role transition. Prediction analyses revealed one significant positive effect of the booster session: emergence of preparedness to provide care. Moreover, with or without the booster session, the program continued to have a positive effect on psychological distress and contributed to the emergence of self-efficacy in dealing with caregiving situations. The booster session had no significant effect on knowledge of services, planning for future care needs, use of reframing as a coping strategy, perceived informal support, and family conflicts. The limited effect observed is discussed in terms of the booster session's content and intensity. Recommendations are made for designing future research on the effect of booster sessions, including the importance of including a

  3. The injection and extraction of SSRF booster

    International Nuclear Information System (INIS)

    Li Yuan; Li Haohu; Liu Guimin; Li Deming

    2008-01-01

    The layout of injection and extraction system were introduced in this paper. The horizontal and vertical injection acceptance are about 23 πmm·mrad and 37 πmm·mrad, respectively, while emittance of the injected beam is 9 πmm·mrad (3σ). This ensures the high injection efficiency. Three slow kickers can form a good bump. The inside position of the entrance of septum is set to 15 mm, where the bumped beam and the extraction beam are 10 mm and 22 mm, respectively, far from the booster central orbit. (authors)

  4. Antibody response to booster vaccination with tetanus and diphtheria in adults exposed to perfluorinated alkylates

    DEFF Research Database (Denmark)

    Kielsen, Katrine; Shamim, Zaiba; Ryder, Lars P.

    2016-01-01

    Recent studies suggest that exposure to perfluorinated alkylate substances (PFASs) may induce immunosuppression in humans and animal models. In this exploratory study, 12 healthy adult volunteers were recruited. With each subject, serum-PFAS concentrations were measured and their antibody responses...... prospectively followed for 30 days after a booster vaccination with diphtheria and tetanus. The results indicated that serum-PFAS concentrations were positively correlated and positively associated with age and male sex. The specific antibody concentrations in serum were increased from Day 4 to Day 10 post......-booster, after which a constant concentration was reached. Serum PFAS concentrations showed significant negative associations with the rate of increase in the antibody responses. Interestingly, this effect was particularly strong for the longer-chain PFASs. All significant associations remained significant after...

  5. Lightweight, fire-retardant, crashworthy aircraft seat cushioning

    Science.gov (United States)

    Haslim, Leonard A.; Mcdonough, Paul T.

    1991-01-01

    A two page discussion of non-aerospace seating applications and the design of NASA's safety seat cushioning (SSC) is presented. The SSC was designed for both safety and comfort in order to replace polyurethane cushioning which is flammable and produces lethal fumes upon combustion. The SSC is composed of advanced fabric reinforced composites and is lightweight, fire-retardent, and crashworthy. The seat design consists of central elliptical tubular spring supports made of fire-resistant and fatigue-durable composites surrounded by a fire-blocking sheath. The cushioning is made crashworthy by incorporating energy-absorbing, viscoelastic layers between the nested, elliptical-hoop springs. The design is intended to provide comfortable seating that meets aircraft-loading requirements without using the conventional polyurethane materials. The designs of an aircraft seat and structural components of the SSC are also presented.

  6. The AGS Booster control system

    International Nuclear Information System (INIS)

    Frankel, R.; Auerbach, E.; Culwick, B.; Clifford, T.; Mandell, S.; Mariotti, R.; Salwen, C.; Schumburg, N.

    1988-01-01

    Although moderate in size, the Booster construction project requires a comprehensive control system. There are three operational modes: as a high intensity proton injector for the AGS, as a heavy ion accelerator and injector supporting a wide range of ions and as a polarized proton storage injector. These requirements are met using a workstation based extension of the existing AGS control system. Since the Booster is joining a complex of existing accelerators, the new system will be capable of supporting multiuser operational scenarios. A short discussion of this system is discussed in this paper

  7. Misuse of restraint systems for children and adults.

    NARCIS (Netherlands)

    Schoon, C.C.

    1992-01-01

    A study is described of the use of child seats in The Netherlands. Four types are used: a) rearward facing baby seat, b) seat with harness belt, c) seat without harness belt but with a shield of foam over which the belt is strapped and d) booster cushion. Seats were examined for the way in which

  8. Beam instrumentation in the AGS Booster

    International Nuclear Information System (INIS)

    Witkover, R.L.

    1991-01-01

    The AGS Booster was designed to accelerate low intensity (2 x 10 10 ) polarized protons, high intensity (1.5x10 13 ) protons and heavy ions through Au +33 . Coping with this wide range of beams, the 3 x 10 -11 Torr vacuum and the radiation environment presented challenges for the beam monitors. Some of the more interesting instrumentation design and performance during the recent Booster proton commissioning will be described

  9. Infant bath seats, drowning and near-drowning.

    Science.gov (United States)

    Byard, R W; Donald, T

    2004-01-01

    To investigate the possible role of infant bathtub seats in drowning and near-drowning episodes in infants. A review was conducted of the files of the Forensic Science Centre and Child Protection Unit, Women's and Children's Hospital, Adelaide, South Australia, for significant immersion incidents in infants involving bathtub seats from January 1998 to December 2003. A total of six cases of drowning occurred over the 6-year period of the study in children under 2 years of age, including two infants. One of these cases, a 7-month-old boy, had been left unattended for some time in an adult bath in a bathtub seat. He was found drowned, having submerged after slipping down and becoming trapped in the seat. Three near-drowning episodes occurred in children under the age of 2 years, including two boys aged 7 and 8 months, both of whom had been left for some time in adult baths in bath seats. Both were successfully resuscitated and treated in hospital. These cases demonstrate the vulnerability of infants to immersion incidents when left unattended in bathtubs. Bathtubs are particularly dangerous for infants as the slippery and smooth surfaces predispose to loss of balance and make escape from water difficult. Infant bathtub seats may give parents and child carers a false sense of security leading to infants being left unattended. Unfortunately, however, infants may fall out of, or slip and become trapped in, such seats. Infants and young children cannot be left unsupervised in water, and devices used as bathing aids such as bathtub seats may contribute to immersion incidents.

  10. Antibody response to booster vaccination with tetanus and diphtheria in adults exposed to perfluorinated alkylates.

    Science.gov (United States)

    Kielsen, Katrine; Shamim, Zaiba; Ryder, Lars P; Nielsen, Flemming; Grandjean, Philippe; Budtz-Jørgensen, Esben; Heilmann, Carsten

    2016-01-01

    Recent studies suggest that exposure to perfluorinated alkylate substances (PFASs) may induce immunosuppression in humans and animal models. In this exploratory study, 12 healthy adult volunteers were recruited. With each subject, serum-PFAS concentrations were measured and their antibody responses prospectively followed for 30 days after a booster vaccination with diphtheria and tetanus. The results indicated that serum-PFAS concentrations were positively correlated and positively associated with age and male sex. The specific antibody concentrations in serum were increased from Day 4 to Day 10 post-booster, after which a constant concentration was reached. Serum PFAS concentrations showed significant negative associations with the rate of increase in the antibody responses. Interestingly, this effect was particularly strong for the longer-chain PFASs. All significant associations remained significant after adjustment for sex and age. Although the study involved a small number of subjects, these findings of a PFAS-associated reduction of the early humoral immune response to booster vaccination in healthy adults supported previous findings of PFAS immunosuppression in larger cohorts. Furthermore, the results suggested that cellular mechanisms right after antigen exposure should be investigated more closely to identify possible mechanisms of immunosuppression from PFAS.

  11. Booster Vaccination: The Role of Reduced Antigen Content Vaccines as a Preschool Booster

    Directory of Open Access Journals (Sweden)

    Giovanni Gabutti

    2014-01-01

    Full Text Available The need for boosters for tetanus, diphtheria, pertussis, and polio, starting from preschool age, is related to the waning immune protection conferred by vaccination, the elimination/reduction of natural boosters due to large-scale immunization programs, and the possibility of reintroduction of wild agents from endemic areas. Taking into account the relevance of safety/tolerability in the compliance with vaccination among the population, it have been assessed whether today enough scientific evidences are available to support the use of dTap-IPV booster in preschool age. The review of the literature was conducted using the PubMed search engine. A total of 41 works has been selected; besides, the documentation produced by the World Health Organization, the European Centre for Disease Control, and the Italian Ministry of Health has been consulted. Many recent papers confirm the opportunity to use a low antigenic dose vaccine starting from 4 to 6 years of age. There is also evidence that 10 years after immunization the rate of seroprotected subjects against diphtheria does not differ significantly between those vaccinated with paediatric dose (DTaP or reduced dose (dTaP or dTap product. The dTpa vaccine is highly immunogenic for diphtheria toxoids regardless of prior vaccination history (2 + 1 and 3 + 1 schedules.

  12. Subcriticality determination in ADS: Valina-Booster experiments

    International Nuclear Information System (INIS)

    Persson, C. M.; Gudowski, W.; Fokau, A.; Bournos, V.; Fokov, Y.; Routkovskaia, C.; Serafimovich, I.; Kiyavitskaya, H.

    2007-01-01

    A major problem in operating a full-scale subcritical accelerator-driven system (ADS) is to ensure sufficient margin to criticality. Therefore, reliable techniques for subcriticality monitoring are required. In order to develop such techniques, a full understanding of existing reactivity determination methods is essential. In this work, reactivity determination methods, such as pulsed neutron source methods and noise methods, are studied experimentally in the subcritical facility YALINA-Booster. YALINA-Booster: The subcritical assembly YALINA-Booster: recently constructed at the Joint Institute for Power and Nuclear Research - Sosny, consists of a subcritical core driven by an external neutron source. The neutron source is a powerful neutron generator consisting of a deuteron accelerator and a target of deuterium or tritium embedded in titanium. Through (d, d) - or (d, t)-reactions neutrons are created with energy around 2.5 MeV and 14.1 MeV respectively. Neutrons are born in the centre of the core and multiply through a lead matrix fuelled with highly enriched uranium (90% and 36%). This zone is referred to as the booster zone and is surrounded by a thermal zone, moderated by polyethylene. In order to reach sufficient high effective multiplication factor, the thermal zone is fuelled by approximately one thousand rods of 10% enriched uranium dioxide in cylindrical geometry. To prevent thermal neutrons from diffusing into the fast booster zone, an interface, consisting of boron carbide and natural uranium rods, is located between the zones. YALINA-Booster has a radial graphite reflector of thickness 24 cm. Experiments: Experiments using the neutron source in pulsed mode will be presented, relying on methods such as the area method and the method of prompt neutron decay rate determination. Moreover, results from noise analysis using for instance the Feynman-α method will be presented

  13. Pregnancy: Should I Use a Seat Belt?

    Science.gov (United States)

    ... passenger has not been shown to affect the safety of an unborn baby in a crash. Injuries from car crashes tend to be less serious in people who are sitting in the back seat. If you are not driving, you may want to sit in the back seat. It is still important to wear a seat belt, no matter where ...

  14. Electronics for damping transverse instabilities for the Fermilab booster synchrotron

    International Nuclear Information System (INIS)

    Higgins, E.F. Jr.

    1977-01-01

    Transverse instabilities are controlled by an active beam damper which corrects the orbit of individual proton bunches in the Fermilab booster synchrotron. The corrective signals, which are in reality processed versions of the beam pick-up data, are applied to the beam via power amplifier/deflector electrodes approximately one turn after sensing the bunch position. The electronic systems of the damper are configured as a closed-loop feedback arrangement. A brief outline is given of the overall damper system configuration, and the beam position detector, coaxial cable delay system, and data receiver are described

  15. Head injury causation scenarios for belted, rear-seated children in frontal impacts.

    Science.gov (United States)

    Bohman, Katarina; Arbogast, Kristy B; Bostrom, Ola

    2011-02-01

    Head injuries are the most common serious injuries sustained by children in motor vehicle crashes and are of critical importance with regard to long-term disability. There is a lack of understanding of how seat belt-restrained children sustain head injuries in frontal impacts. The aim of the study was to identify the AIS2+ head injury causation scenarios for rear-seated, belt-restrained children in frontal impacts, including the set of parameters contributing to the injury. In-depth crash investigations from two National Highway Traffic Safety Administration (NHTSA) databases, the National Automotive Sampling System-Crashworthiness Data System (NASS-CDS; 1997-2008) and the Crash Injury Research and Engineering Network (CIREN; 1996-2009), were collected and analyzed in detail. Selection criteria were all frontal impacts with principal direction of force (PDOF) of 11, 12, and 1 o'clock involving rear-seated, three-point belt-restrained, with or without booster cushion, children from 3 to 13 years with an AIS2+ head injury. Cases were analyzed using the BioTab method of injury causation assessment in order to systematically analyze the injury causation scenario for each case. There were 27 cases meeting the inclusion criteria, 19 cases with MAIS2 head injuries and 8 cases with MAIS3+ head injuries, including 2 fatalities. Three major injury causation scenarios were identified, including head contact with seatback (10 cases), head contact with side interior (7 cases,) and no evidence of head contact (9 cases). Head injuries with seatback or side interior contact typically included a PDOF greater than 10 degree (similar to the Insurance Institute for Highway Safety [IIHS] and EuroNCAP offset frontal testing) and vehicle maneuvers. For seatback contact, the vehicle's movements contributed to occupant kinematics inboard the vehicle, causing a less than optimal restraint of the torso and/or torso roll out of the shoulder belt. For side interior contact, the PDOF and

  16. 14 CFR 135.113 - Passenger occupancy of pilot seat.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Passenger occupancy of pilot seat. 135.113... Operations § 135.113 Passenger occupancy of pilot seat. No certificate holder may operate an aircraft type certificated after October 15, 1971, that has a passenger seating configuration, excluding any pilot seat, of...

  17. The Effects of Microgravity on Seated Height (Spinal Elongation)

    Science.gov (United States)

    Young, K. S.; Rajulu, S.

    2011-01-01

    ABSTRACT Many physiological factors, such as spinal elongation, fluid shifts, bone atrophy, and muscle loss, occur during an exposure to a microgravity environment. Spinal elongation is just one of the factors that can also affect the safety and performance of a crewmember while in space. Spinal elongation occurs due to the lack of gravity/compression on the spinal column. This allows for the straightening of the natural spinal curve. There is a possible fluid shift in the inter-vertebral disks that may also result in changes in height. This study aims at collecting the overall change in seated height for crewmembers exposed to a microgravity environment. During previous Programs, Apollo-Soyuz Test Project (ASTP) and Skylab, spinal elongation data was collected from a small number of subjects in a standing posture but were limited in scope. Data from these studies indicated a quick increase in stature during the first few days of weightlessness, after which stature growth reached a plateau resulting in up to a 3% increase of the original measurement [1-5]. However, this data was collected only for crewmembers in standing posture and not in a seated posture. Seated height may have a different effect than standing height due to a change in posture as well as due to a compounded effect of wearing restraints and a potential compression of the gluteal area. Seated height was deemed as a critical measurement in the design of the Constellation Program s (CxP) Crew Exploration Vehicle (CEV), called Orion which is now the point-of-departure vehicle for the Multi-Purpose Crew Vehicle (MPCV) Program; therefore a better understanding of the effects of microgravity on seated height is necessary. Potential changes in seated height that may not have impacted crew accommodation in previous Programs will have significant effects on crew accommodation due to the layout of seats in the Orion.. The current and existing configuration is such that the four crewmembers are stacked two by

  18. Compliance with Seat Belt Use in Makurdi, Nigeria: An ...

    African Journals Online (AJOL)

    Background: Seat belts are designed to reduce injuries due to road crash among vehicle occupants. Aims: This study aims to determine the availability of seat belt in vehicles and compliance with seat belt use among vehicle occupants. Materials and methods: This was a 24‑h direct observational study of seat belt usage ...

  19. Development of electrostatic charging evaluation equipment for automobile seat; Jidoshayo seat no taidensei shiken hyoka sochi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Maeda, K [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    When passengers get out of vehicle, electrostatics is generated by separation of seat cloth and passenger cloth, and then charged to passenger`s body. It has been impossible for us to simulate this induction charging phenomenon with current evaluation equipments. We developed a new seat cloth evaluation equipments using induction charging plate, which enables us to simulate the phenomenon. This paper describes this new electrostatic charging evaluation method for automobile seat cloth. 5 refs., 6 figs.

  20. Children's and Adults' Comfort Experience of Extra Seat Belts When Riding in the Rear Seat of a Passenger Car.

    Science.gov (United States)

    Osvalder, Anna-Lisa; Hansson, Ida; Bohman, Katarina

    2015-01-01

    The objective of this study was to explore passengers' comfort experience of extra seat belts during on-road driving in the rear seat of a passenger car and to investigate how the use of extra belts affects children's and adults' attitudes to the product. Two different seat belt systems were tested, criss-cross (CC) and backpack (BP), consisting of the standard 3-point belt together with an additional 2-point belt. In total, 32 participants (15 children aged 6-10, 6 youths aged 11-15, and 11 adults aged 20-79, who differed considerably in size, shape, and proportions) traveled for one hour with each system, including city traffic and highway driving. Four video cameras monitored the test subject during the drive. Subjective data regarding emotions and perceived discomfort were collected in questionnaires every 20 min. A semistructured interview was held afterwards. All participant groups accepted the new products and especially the increased feeling of safety (P car. CC was appreciated for its symmetry, comfort, and the perceived feeling of safety. Some participants found CC unpleasant because the belts tended to slip close to the neck, described as a strangling feeling. BP was simpler to use and did not cause annoyance to the neck in the way CC did. Instead, it felt asymmetric and to some extent less safe than CC. Body size and shape affected seat belt fit to a great extent, which in turn affected the experience of comfort, both initially and over time. Perceived safety benefit and experienced comfort were the most determinant factors for the attitude toward the extra seat belts. The extra seat belts were perceived as being better than the participants had expected before the test, and they became more used to them over time. This exploratory study provided valuable knowledge from a user perspective for further development of new seat belt systems in cars. In addition to an increased feeling of safety, seat belt fit and comfort are supplementary influencing

  1. Legislating child restraint usage -Its effect on self-reported child restraint use rates in a central city.

    Science.gov (United States)

    Brixey, Suzanne; Ravindran, Karthik; Guse, Clare E

    2010-02-01

    To assess the effect of the newly enacted child passenger safety law, Wisconsin Act 106, on self-report of proper restraint usage of children in Milwaukee's central city population. A prospective, non-randomized study design was used. The settings used were (a) a pediatric urban health center, and (b) two Women, Infants and Children offices in Milwaukee, Wisconsin. Participants included 11,566 surveys collected over 18 months that spanned the pre-legislation and post-legislation time periods from February 2006 through August 2008. The study set out to assess appropriate child passenger restraint. The results showed that the changes in adjusted proper restraint usage rates for infants between the pre-law, grace period, and post-fine periods were 94%, 94%, and 94% respectively. For children 1-3years old, the adjusted proper usage rates were 65%, 63%, and 59%, respectively. And for children 4-7years old, the rates were 43%, 44% and 42%, respectively. There was a significant increase in premature booster seat use in children who should have been restrained in a rear- or forward-facing car seat (10% pre-law, 12% grace period, 20% post-fine; padvertising and marketing to the correct age group, ease of installation, and mechanisms to prevent incorrect safety strap and harness placement. To ensure accurate and consistent use on every trip, car seat manufacturers must ensure that best practice recommendations for use as well as age, weight, and height be clearly specified on each child restraint. The authors support the United States Department of Transportation's new consumer program that will assist caregivers in identifying the child seat that will fit in their vehicle. In addition, due to the increase in premature graduation of children into belt-positioning booster seats noted as a result of legislation, promoting and marketing booster seat use for children less than 40 pounds should not be accepted. Child passenger safety technicians must continue to promote best

  2. SIMULATIONS OF BOOSTER INJECTION EFFICIENCY FOR THE APS-UPGRADE

    Energy Technology Data Exchange (ETDEWEB)

    Calvey, J.; Borland, M.; Harkay, K.; Lindberg, R.; Yao, C.-Y.

    2017-06-25

    The APS-Upgrade will require the injector chain to provide high single bunch charge for swap-out injection. One possible limiting factor to achieving this is an observed reduction of injection efficiency into the booster synchrotron at high charge. We have simulated booster injection using the particle tracking code elegant, including a model for the booster impedance and beam loading in the RF cavities. The simulations point to two possible causes for reduced efficiency: energy oscillations leading to losses at high dispersion locations, and a vertical beam size blowup caused by ions in the Particle Accumulator Ring. We also show that the efficiency is much higher in an alternate booster lattice with smaller vertical beta function and zero dispersion in the straight sections.

  3. Assessment of changes in spine curvatures and the sensations caused in three different types of working seats

    Directory of Open Access Journals (Sweden)

    Caique de Melo do Espírito Santo

    2017-08-01

    Full Text Available Abstract Aims This study aimed to evaluate the changes in the spine curvatures and the sensations caused by different types of seats: standard, ischial support and salli. Methods The analyzes were performed by the kinematics and scales of discomfort and pain in 14 healthy subjects. The data collection occurred in three days, one day for each type of seat. The subjects answered questionnaires and were assessed for placement of kinematic markers used to measure the thoracic, thoraco-lumbar and lumbar angles. Each trial was conducted in a sixty-minute period on each chair. Results and conclusions The results showed that the salli seat type causes larger lumbar angles, which is consistent with the maintenance of lumbar lordosis. Likewise, the salli seat showed smaller thoraco-lumbar angle, which is consistent with smaller inferior thoracic kyphosis. Paradoxically, the ischial support seat produced less discomfort and pain than salli type. And finally, the longer the sitting position was the higher the score on the discomfort scale.

  4. Space shuttle booster separation motor design

    Science.gov (United States)

    Smith, G. W.; Chase, C. A.

    1976-01-01

    The separation characteristics of the space shuttle solid rocket boosters (SRBs) are introduced along with the system level requirements for the booster separation motors (BSMs). These system requirements are then translated into specific motor requirements that control the design of the BSM. Each motor component is discussed including its geometry, material selection, and fabrication process. Also discussed is the propellant selection, grain design, and performance capabilities of the motor. The upcoming test program to develop and qualify the motor is outlined.

  5. SEAT CHOICE AND DISTANCE JUDGMENT IN PUBLIC SPACES (1).

    Science.gov (United States)

    Neto, Olavo Avalone; Munakata, Jun

    2015-10-01

    This research assessed whether public space users will adopt a least-effort approach and choose a less suitable seat nearby or seek the most suitable seat, even if it is farther away from them when the decision is made. How distance assessment affects seat choice was investigated through an observational survey, which allowed the identification of behavioral patterns. Those behavioral patterns were then tested in a paired comparison experiment with 40 participants. The results showed that the effect of distance on seat choice is related to the difference in distance between the options and that a sufficient difference can cause trade-offs between distance and seat properties. The necessary difference in distance is conditioned by the activity and the seat properties.

  6. 75 FR 36062 - Availability of Conservation Seat and Diving Operations Seat for the Flower Garden Banks National...

    Science.gov (United States)

    2010-06-24

    ... Conservation Seat and Diving Operations Seat for the Flower Garden Banks National Marine Sanctuary Advisory... Flower Garden Banks National Marine Sanctuary Advisory Council: Conservation and Diving Operations... Jennifer Morgan, NOAA--Flower Garden Banks National Marine Sanctuary, 4700 Avenue U, Bldg. 216, Galveston...

  7. The AGS Booster main ring power supply system

    International Nuclear Information System (INIS)

    Soukas, A.; Hughes, K.; Sandberg, J.; Toldo, F.; Zhang, S.Y.

    1989-01-01

    The AGS Booster is being designed as a very versatile particle accelerator. Its primary function is to be a high quality injector to the currently operating Alternating Gradient Synchrotron (AGS). The Booster/AGS combination will produce proton intensities greater than 5 x 10 13 protons per pulse (ppp), and accelerate heavy ions, with mass up to 200, to a maximum energy of 15 GeV per atomic mass unit (GeV/amu). The power supply for the Booster Main Ring (BMRPS) has to accommodate a wide range of cycles and a wide range of operating parameters. The cycles range from storage for several seconds to rapid cycling at 7.5 Hz. The peak output power is 18 MW. This paper will describe the AGS Booster machine powering requirements, the choice of power supply, the a.c. circuit tie-in and its associated problems and some of the details of the design of the BMRPS. 9 refs., 2 figs

  8. Child Passenger Safety (A Minute of Health with CDC)

    Centers for Disease Control (CDC) Podcasts

    2016-09-29

    Using the correct car seat for your child can be a lifesaver. This podcast discusses the importance of ensuring children are buckled up in car seats or booster seats that are appropriate for their age and size until adult seat belts fit properly. .  Created: 9/29/2016 by MMWR.   Date Released: 9/29/2016.

  9. Exploring the design of a lightweight, sustainable and comfortable aircraft seat.

    Science.gov (United States)

    Kokorikou, A; Vink, P; de Pauw, I C; Braca, A

    2016-07-19

    Making a lightweight seat that is also comfortable can be contradictory because usually comfort improvement means adding a feature (e.g. headrest, adjustable lumbar support, movable armrests, integrated massage systems, etc.), which makes seats heavier. This paper explores the design of an economy class aircraft seat that aims to be lightweight, comfortable and sustainable. Theory about comfort in seats, ergonomics, lightweight design, Biomimicry and Cradle to cradle was studied and resulted in a list of requirements that the new seat should satisfy. The design process resulted in a new seat that is 36% lighter than the reference seat, which showed that a significant weight reduction can be achieved. This was completed by re-designing the backrest and seat pan and integrating their functions into a reduced number of parts. Apart from the weight reduction that helps in reducing the airplane's environmental impact, the seat also satisfies most of the other sustainability requirements such as the use of recyclable materials, design for disassembly, easy to repair. A user test compared the new seat with a premium economy class aircraft seat and the level of comfort was similar. Strong points of the new design were identified such as the lumbar support and the cushioning material, as well as shortcomings on which the seat needs to be improved, like the seat pan length and the first impression. Long term comfort tests are still needed as the seat is meant for long-haul flights.

  10. Wheelchair Seating Assessment and Intervention: A Comparison between Telerehabilitation and Face-to-Face Service

    Directory of Open Access Journals (Sweden)

    Ingrid G Barlow

    2009-09-01

    Full Text Available This study compared outcomes of wheelchair seating and positioning interventions provided by telerehabilitation (n=10 and face-to-face (n=20; 10 in each of two comparison groups, one urban and one rural. Comparison clients were matched to the telerehabilitation clients in age, diagnosis, and type of seating components received. Clients and referring therapists rated their satisfaction and identified if seating intervention goals were met. Clients recorded travel expenses incurred or saved, and all therapists recorded time spent providing service. Wait times and completion times were tracked. Clients seen by telerehabilitation had similar satisfaction ratings and were as likely to have their goals met as clients seen face-to-face; telerehabilitation clients saved travel costs. Rural referring therapists who used telerehabilitation spent more time in preparation and follow-up than the other groups. Clients assessed by telerehabilitation had shorter wait times for assessment than rural face-to-face clients, but their interventions took as long to complete. Keywords: Telerehabilitation, Telehealth, Videoconferencing, Wheelchair Seating, Outcomes, Rehabilitation

  11. An efficiency booster for energy conversion in natural circulation loops

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Dongqing, E-mail: wangdongqing@stu.xjtu.edu.cn [School of Nuclear Science and Technology, Xi’an Jiaotong University, Xi’an, Shaanxi 710049 (China); Beijing Computational Science Research Center, Beijing 100084 (China); Jiang, Jin, E-mail: jjiang@eng.uwo.ca [Department of Electrical and Computer Engineering, The University of Western Ontario, London, Ontario N6A 5B9 (Canada); Beijing Computational Science Research Center, Beijing 100084 (China)

    2016-08-01

    Highlights: • Low driving power conversion efficiency of natural circulation loops is proved. • The low conversion efficiency leads to low heat transfer capacity of such loops. • An efficiency booster is designed with turbine to increase the efficiency. • Performance of the proposed booster has been numerically simulated. • The booster drastically enhances heat transfer capacity of such loops. - Abstract: In this paper, the capacity of a natural circulation loop for transferring heat from a heat source to a heat sink has been analyzed. It is concluded that the capacity of the natural circulation loop depends on the conversion efficiency of the thermal energy from the heat source to the driving force for the circulation of the flow. The low conversion efficiency leading to weak driving force in such loops has been demonstrated analytically and validated through simulation results. This issue has resulted in a low heat transfer capacity in the circulation loop. To increase the heat transfer capacity, one has to improve this efficiency. To meet such a need, a novel efficiency booster has been developed in this paper. The booster essentially increases the flow driving force and hence significantly improves the overall heat transfer capacity. Design and analysis of this booster have been performed in detail. The performance has been examined through extensive computer simulations. It is concluded that the booster can indeed drastically improve the heat transfer capacity of the natural circulation loop.

  12. An efficiency booster for energy conversion in natural circulation loops

    International Nuclear Information System (INIS)

    Wang, Dongqing; Jiang, Jin

    2016-01-01

    Highlights: • Low driving power conversion efficiency of natural circulation loops is proved. • The low conversion efficiency leads to low heat transfer capacity of such loops. • An efficiency booster is designed with turbine to increase the efficiency. • Performance of the proposed booster has been numerically simulated. • The booster drastically enhances heat transfer capacity of such loops. - Abstract: In this paper, the capacity of a natural circulation loop for transferring heat from a heat source to a heat sink has been analyzed. It is concluded that the capacity of the natural circulation loop depends on the conversion efficiency of the thermal energy from the heat source to the driving force for the circulation of the flow. The low conversion efficiency leading to weak driving force in such loops has been demonstrated analytically and validated through simulation results. This issue has resulted in a low heat transfer capacity in the circulation loop. To increase the heat transfer capacity, one has to improve this efficiency. To meet such a need, a novel efficiency booster has been developed in this paper. The booster essentially increases the flow driving force and hence significantly improves the overall heat transfer capacity. Design and analysis of this booster have been performed in detail. The performance has been examined through extensive computer simulations. It is concluded that the booster can indeed drastically improve the heat transfer capacity of the natural circulation loop.

  13. Deep-seated sarcomas of the penis

    Directory of Open Access Journals (Sweden)

    Alberto A. Antunes

    2005-06-01

    Full Text Available Mesenchymal neoplasias represent 5% of tumors affecting the penis. Due to the rarity of such tumors, there is no agreement concerning the best method for staging and managing these patients. Sarcomas of the penis can be classified as deep-seated if they derive from the structures forming the spongy body and the cavernous bodies. Superficial lesions are usually low-grade and show a small tendency towards distant metastasis. In contrast, deep-seated lesions usually show behavior that is more aggressive and have poorer prognosis. The authors report 3 cases of deep-seated primary sarcomas of the penis and review the literature on this rare and aggressive neoplasia.

  14. New beam instrumentation in the AGS Booster

    International Nuclear Information System (INIS)

    Witkover, R.L.

    1991-01-01

    The AGS Booster was designed to accelerate beams from 2x10 10 polarized protons to 1.5x10 13 protons and heavy ions through Au +33 . The range of beam parameters and the high vacuum, and radiation environment presented challenges for the beam instrumentation. Some interesting beam monitors in the Booster and transport lines, will be described. Where available, results will be presented. 21 refs., 7 figs

  15. The SSRL injector beam position monitoring systems

    International Nuclear Information System (INIS)

    Lavender, W.; Baird, S.; Brennan, S.; Borland, M.; Hettel, R.; Nuhn, H.D.; Ortiz, R.; Safranek, J.; Sebek, J.; Wermelskirchen, C.; Yang, J.

    1991-01-01

    The beam position monitoring system of the SSRL injector forms a vital component of its operation. Several different types of instrumentation are used to measure the position or intensity of the electron beam in the injector. These include current toroids, fluorescent screens, Faraday cups, the 'Q' meter, a synchrotron light monitor, and electron beam position monitors. This paper focuses on the use of the electron beam position monitors to measure electron trajectories in the injector transport lines and the booster ring. The design of the beam position monitors is described in another paper to be presented at this conference. There are three different beam position monitor systems in the injector. One system consists of a set of five BPMs located on the injection transport line from the linac to the booster (known as the LTB line). There is a second system of six BPMs located on the ejection transport line (known as the BTS line). Finally, there is an array of 40 BPMs installed on the main booster ring itself. This article describes the software and processing electronics of the systems used to measure electron beam trajectories for the new SSRL injector for SPEAR

  16. Accelerating RF cavity of the Booster

    CERN Multimedia

    CERN PhotoLab

    1981-01-01

    Each of the 4 PS Booster rings has a single accelerating cavity. It consists of 2 quarter-wave ferrite-loaded resonators. There are 2 figure-of-eight loops on the ferrite loads for tuning the frequency throughout the acceleration cycle, from 3 to 8 MHz (from 50 MeV at injection to the original Booster energy of 800 MeV, 2 GeV today). The cavities have a flat design, to fit the ring-to-ring distance of 36 cm. The tube for forced-air cooling is visible in the left front. See also 8301084.

  17. Accelerating RF cavity of the Booster

    CERN Multimedia

    CERN PhotoLab

    1983-01-01

    Each of the 4 PS Booster rings has a single accelerating cavity.It consists of 2 quarter-wave ferrite-loaded resonators. 2 figure-of-eight loops tune the frequency throughout the accelerating cycle, from 3 to 8 MHz (from 50 MeV at injection to the original Booster energy of 800 MeV, 2 GeV today). The cavities have a flat design, to fit the ring-to-ring distance of 36 cm, and are forced-air cooled. The 2 round objects in the front-compartments are the final-stage power-tetrodes. See also 8111095.

  18. Weak Depolarizing Resonances in the 3-TeV VLHC Booster

    International Nuclear Information System (INIS)

    Anferov, V.A.

    1999-01-01

    The possibility of polarized-proton-beam acceleration in the proposed low-field 3-TeV VLHC booster is considered. We find that the low-field combined function magnets in the booster's long FODO cells cause an inadvertent cancellation of most depolarizing fields due to a mechanism suggested earlier by Chao and Derbenev [Part.Accel.36, 25 (1991)]. The strongest spin-depolarizing resonances in the 3-TeV booster seem to be similar in strength to those in the 250-GeV RHIC. Moreover, the strength of the 3-TeV booster's strongest intrinsic depolarizing resonances decreases with energy, in contrast with the energy growth of the depolarizing resonance's strength in most proton synchrotrons. copyright 1999 The American Physical Society

  19. Impaired Driving

    Science.gov (United States)

    ... Get the Facts What Works: Strategies to Increase Car Seat and Booster Seat ... narcotics. 3 That’s one percent of the 111 million self-reported episodes of alcohol-impaired driving among U.S. ...

  20. Modeling the Impact of Space Suit Components and Anthropometry on the Center of Mass of a Seated Crewmember

    Science.gov (United States)

    Blackledge, Christopher; Margerum, Sarah; Ferrer, Mike; Morency, Richard; Rajulu, Sudhakar

    2010-01-01

    The Crew Impact Attenuation System (CIAS) is the energy-absorbing strut concept that dampens Orion Crew Exploration Vehicle (CEV) landing loads to levels sustainable by the crew. Significant COM variations across suited crew configurations would amplify the inertial effects of the pallet and potentially create unacceptable crew loading during launch and landing. The objective of this study was to obtain data needed for dynamic simulation models by quantifying the effects of posture, suit components, and the expected range of anthropometry on the COM of a seated individual. Several elements are required for the COM calculation of a suited human in a seated position: anthropometry, body segment mass, suit component mass, suit component location relative to the body, and joint angles defining the seated posture. Three-dimensional (3D) human body models, suit mass data, and vector calculus were utilized to compute the COM positions for 12 boundary manikins in two different seated postures. The analysis focused on two objectives: (1) quantify how much the wholebody COM varied from the smallest to largest subject and (2) quantify the effects of the suit components on the overall COM in each seat configuration. The location of the anterior-posterior COM varied across all boundary manikins by about 7 cm, and the vertical COM varied by approximately 9 to 10 cm. The mediolateral COM varied by 1.2 cm from the midline sagittal plane for both seat configurations. The suit components caused an anterior shift of the total COM by approximately 2 cm and a shift to the right along the mediolateral axis of 0.4 cm for both seat configurations. When the seat configuration was in the standard posture the suited vertical COM shifted inferiorly by as much as 1 cm, whereas in the CEV posture the vertical COM had no appreciable change. These general differences were due to the high proportion of suit mass located in the boots and lower legs and their corresponding distance from the body COM

  1. Civil aircraft side-facing seat research summary.

    Science.gov (United States)

    2012-11-01

    The Federal Aviation Administration (FAA) has standards and regulations that are intended to protect aircraft : occupants in the event of a crash. However, side-facing seats were not specifically addressed when aircraft seat : dynamic test standards ...

  2. New beam instrumentation in the AGS Booster

    Energy Technology Data Exchange (ETDEWEB)

    Witkover, R.L.

    1991-01-01

    The AGS Booster was designed to accelerate beams from 2{times}10{sup 10} polarized protons to 1.5{times}10{sup 13} protons and heavy ions through Au{sup +33}. The range of beam parameters and the high vacuum, and radiation environment presented challenges for the beam instrumentation. Some interesting beam monitors in the Booster and transport lines, will be described. Where available, results will be presented. 21 refs., 7 figs.

  3. Booster Main Engine Selection Criteria for the Liquid Fly-Back Booster

    Science.gov (United States)

    Ryan, Richard M.; Rothschild, William J.; Christensen, David L.

    1998-01-01

    The Liquid Fly-Back Booster (LFBB) Program seeks to enhance the Space Shuttle system safety performance and economy of operations through the use of an advanced, liquid propellant Booster Main Engine (BME). There are several viable BME candidates that could be suitable for this application. The objective of this study was to identify the key criteria to be applied in selecting among these BME candidates. This study involved an assessment of influences on the overall LFBB utility due to variations in the candidate rocket engines' characteristics. This includes BME impacts on vehicle system weight, perfortnance,design approaches, abort modes, margins of safety, engine-out operations, and maintenance and support concepts. Systems engineering analyses and trade studies were performed to identify the LFBB system level sensitivities to a wide variety of BME related parameters. This presentation summarizes these trade studies and the resulting findings of the LFBB design teams regarding the BME characteristics that most significantly affect the LFBB system. The resulting BME choice should offer the best combination of reliability, performance, reusability, robustness, cost, and risk for the LFBB program.

  4. Space Launch System Accelerated Booster Development Cycle

    Science.gov (United States)

    Arockiam, Nicole; Whittecar, William; Edwards, Stephen

    2012-01-01

    With the retirement of the Space Shuttle, NASA is seeking to reinvigorate the national space program and recapture the public s interest in human space exploration by developing missions to the Moon, near-earth asteroids, Lagrange points, Mars, and beyond. The would-be successor to the Space Shuttle, NASA s Constellation Program, planned to take humans back to the Moon by 2020, but due to budgetary constraints was cancelled in 2010 in search of a more "affordable, sustainable, and realistic" concept2. Following a number of studies, the much anticipated Space Launch System (SLS) was unveiled in September of 2011. The SLS core architecture consists of a cryogenic first stage with five Space Shuttle Main Engines (SSMEs), and a cryogenic second stage using a new J-2X engine3. The baseline configuration employs two 5-segment solid rocket boosters to achieve a 70 metric ton payload capability, but a new, more capable booster system will be required to attain the goal of 130 metric tons to orbit. To this end, NASA s Marshall Space Flight Center recently released a NASA Research Announcement (NRA) entitled "Space Launch System (SLS) Advanced Booster Engineering Demonstration and/or Risk Reduction." The increased emphasis on affordability is evident in the language used in the NRA, which is focused on risk reduction "leading to an affordable Advanced Booster that meets the evolved capabilities of SLS" and "enabling competition" to "enhance SLS affordability. The purpose of the work presented in this paper is to perform an independent assessment of the elements that make up an affordable and realistic path forward for the SLS booster system, utilizing advanced design methods and technology evaluation techniques. The goal is to identify elements that will enable a more sustainable development program by exploring the trade space of heavy lift booster systems and focusing on affordability, operability, and reliability at the system and subsystem levels5. For this study

  5. Technical note: Spine loading in automotive seating

    NARCIS (Netherlands)

    Zenk, R.; Franz, M.; Bubb, H.; Vink, P.

    2012-01-01

    For car manufacturers, seat comfort is becoming more important in distinguishing themselves from their competitors. Therefore, many studies on participative seat comfort are carried out. In this paper, an objective assessment approach is reported which evaluates the concept of "optimal load

  6. 49 CFR 571.207 - Standard No. 207; Seating systems.

    Science.gov (United States)

    2010-10-01

    ... standard establishes requirements for seats, their attachment assemblies, and their installation to....2. General performance requirements. When tested in accordance with S5, each occupant seat shall... than a school bus; a passenger seat on a school bus with a GVWR greater than 4,536 kilograms (10,000...

  7. Active Suspension of Truck Seat

    Directory of Open Access Journals (Sweden)

    Masaaki Kawana

    1998-01-01

    Full Text Available The driver’s seat of a heavy duty truck is usually mounted on a spring–damper assembly anchored to the cab floor. To improve riding comfort, this study investigated the effects of mounting a computer-controlled actuator in parallel with the traditional spring–damper assembly. A dynamic model of the seat is represented by a two degree-of-freedom system, including a cushion. In this paper, a control system is designed, using optimal control theory, which minimizes rms vertical acceleration at a point representing the driver’s hip point. In this system, accelerations of the hip point, the seat frame and the cab floor are picked up and integrated to obtain the state variables to be fed back and fed forward to the actuator through a digital computer. The actuator is constructed with electric servo-motor and ball-screw mechanism. The experimental study was carried out on a shaker, which simulates the vibrations of the cab floor in actual service. Results were obtained for both a dummy and a real human body. The vibration test produced rms accelerations of the seat and the hip point of about 1.0 m/s2 without the actuator, while the rms accelerations were suppressed to about 0.5 m/s2 at a rms input voltage to the servo-motor of 1.0 V.

  8. Booster parameter list

    International Nuclear Information System (INIS)

    Parsa, Z.

    1986-10-01

    The AGS Booster is designed to be an intermediate synchrotron injector for the AGS, capable of accelerating protons from 200 MeV to 1.5 GeV. The parameters listed include beam and operational parameters and lattice parameters, as well as parameters pertaining to the accelerator's magnets, vacuum system, radio frequency acceleration system, and the tunnel. 60 refs., 41 figs

  9. The effect of seated pelvic tilt on posterior edge-loading in total hip arthroplasty: A finite element investigation.

    Science.gov (United States)

    Pierrepont, Jim; Yang, Long; Arulampalam, Jevan; Stambouzou, Catherine; Miles, Brad; Li, Qing

    2018-03-01

    Edge-loading of a ceramic-on-ceramic total hip replacement can lead to reproducible squeaking and revision. A patient's functional acetabular cup orientation, driven by their pelvic tilt, has been shown to be a significant factor in squeaking during hip flexion. The aim of this study was to investigate the effect of seated pelvic tilt on the contact mechanics at the ceramic bearing surface. A finite element model of a ceramic-on-ceramic total hip replacement was created. The cup was orientated at 40° inclination and 15° anteversion relative to the anterior pelvic plane. The stem was flexed 90° to replicate sitting in a chair. The model was loaded using data from in vivo measurements taken during a sit-to-stand activity. The pelvis was modelled in seven different sagittal positions, ranging from -30° to 30° of pelvic tilt, where a positive value denotes anterior pelvic tilt. Three different head sizes were investigated: 32, 36 and 40 mm. The maximum contact pressure and contact patch to rim distance were determined for each of the 21 simulations. Edge-loading (contact patch to rim distance Edge-loading initiated at seated pelvic tilts of 7°, 9° and 5° for the 32, 36 and 40 mm heads, respectively. Patients with anterior pelvic tilts in the seated position are susceptible to posterior edge-loading. As the position of the pelvis when seated is patient specific, cup orientation should be adjusted on an individual basis to minimise edge-loading.

  10. Mathematical modeling of compression processes in air-driven boosters

    International Nuclear Information System (INIS)

    Li Zeyu; Zhao Yuanyang; Li Liansheng; Shu Pengcheng

    2007-01-01

    The compressed air in normal pressure is used as the source of power of the air-driven booster. The continuous working of air-driven boosters relies on the difference of surface area between driven piston and driving piston, i.e., the different forces acting on the pistons. When the working surface area of the driving piston for providing power is greater than that of the driven piston for compressing gas, the gas in compression chamber will be compressed. On the basis of the first law of thermodynamics, the motion regulation of piston is analyzed and the mathematical model of compression processes is set up. Giving a calculating example, the vary trends of gas pressure and pistons' move in working process of booster have been gotten. The change of parameters at different working conditions is also calculated and compared. And the corresponding results can be referred in the design of air-driven boosters

  11. A target fibre study on seats in public houses.

    Science.gov (United States)

    Kelly, E; Griffin, R M

    1998-01-01

    A target fibre survey was conducted to assess the random occurrence of a blue wool fibre on seats in public houses throughout the United Kingdom. Fibre tape lifts were taken from 80 seats. Four seats yielded matching fibres and five of these were found on one seat. A total of 292 fibres were identified; nine fibres proved indistinguishable from the target after comparison microscopy, microspectro-photometry and attempts at thin layer chromatography, and two of these fibres were still apparently indistinguishable after TLC analysis although only one dye component was visible.

  12. The Study of Fabric Performance for Car Seats

    Directory of Open Access Journals (Sweden)

    Antonin Havelka

    2017-09-01

    Full Text Available This paper deals with the investigation of the performance of car seat fabrics in terms of physiological comfort of sitting, specifi cally their water vapour resistance and air permeability. The current work presents an alternative approach to increasing the effectiveness of car seat fabrics through a combination of newly designed middle layer with forced convection achieved by a supplementary suction ventilation device. The supplementary device was designed to measure water vapour permeability by means of the sweating guarded hot plate (SGHP system. It consists of two parts: a frame to grip a tested sample for measurements within the SGHP system and two suction ventilators which are arranged at one end of the mentioned frame in order to provide suction into the tested fabric plane during the SGHP test. The results of this investigation show that water vapour transport is increased by approximately 20% compared to the standard way of measurement by means of SGHP because of forced air flow in the plane of ribbed – channelled structure of the car seat middle layer. The findings of this study have a number of important implications for future practice. The combination of a car seat cover with channelled structure and forced air fl ow improves physiological comfort of sitting which is a key issue for both drivers and manufacturers. The suggested device for forced air flow convection in the plane of a car seat fabric has not yet been part of an actual car seat, however it is possible to use its principles in a smart car seat prototype.

  13. 75 FR 66686 - Federal Motor Vehicle Safety Standards; Seat Belt Assembly Anchorages, School Bus Passenger...

    Science.gov (United States)

    2010-10-29

    ... loose belts) also applies to seats that have wheelchair positions or side emergency doors behind them... have wheelchair positions or side emergency doors behind them); and, the test requirements for self... which correspond to the size of some high school football players) and school buses closer in weight to...

  14. Seat belt injuries and sigmoid colon trauma.

    OpenAIRE

    Eltahir, E M; Hamilton, D

    1997-01-01

    Colonic seat belt injuries are rare but carry higher mortality rates than small bowel injuries. The case of a 44 year old man is described who had severe sigmoid colon compression injury from his seat belt a few days after a road traffic accident.

  15. Using haptic feedback to increase seat belt use : traffic tech.

    Science.gov (United States)

    2011-07-01

    The legacy of research on increasing seat belt use has : focused on enactment of seat belt legislation, public education, : high-visibility police enforcement, and seat belt : reminder systems. Several behavioral programs have : produced large, susta...

  16. Yalina booster subcritical assembly performance with low enriched uranium fuel

    International Nuclear Information System (INIS)

    Talamo, Alberto; Gohar, Yousry

    2011-01-01

    The YALINA Booster facility is a subcritical assembly located in Minsk, Belarus. The facility has special features that result in fast and thermal neutron spectra in different zones. The fast zone of the assembly uses a lead matrix and uranium fuels with different enrichments: 90% and 36%, 36%, or 21%. The thermal zone of the assembly contains 10% enriched uranium fuel in a polyethylene matrix. This study discusses the performance of the three YALINA Booster configurations with the different fuel enrichments. In order to maintain the same subcriticality level in the three configurations, the number of fuel rods in the thermal zone is increased as the uranium fuel enrichment in the fast zone is decreased. The maximum number of fuel rods that can be loaded in the thermal zone is about 1185. Consequently, the neutron multiplication of the configuration with 21% enriched uranium fuel in the fast zone is enhanced by changing the position of the boron carbide and the natural uranium absorber rods, located between the fast and the thermal zones, to form an annular rather than a square arrangement. (author)

  17. Yalina booster subcritical assembly performance with low enriched uranium fuel

    Energy Technology Data Exchange (ETDEWEB)

    Talamo, Alberto; Gohar, Yousry, E-mail: alby@anl.gov [Argonne National Laboratory, Lemont, IL (United States)

    2011-07-01

    The YALINA Booster facility is a subcritical assembly located in Minsk, Belarus. The facility has special features that result in fast and thermal neutron spectra in different zones. The fast zone of the assembly uses a lead matrix and uranium fuels with different enrichments: 90% and 36%, 36%, or 21%. The thermal zone of the assembly contains 10% enriched uranium fuel in a polyethylene matrix. This study discusses the performance of the three YALINA Booster configurations with the different fuel enrichments. In order to maintain the same subcriticality level in the three configurations, the number of fuel rods in the thermal zone is increased as the uranium fuel enrichment in the fast zone is decreased. The maximum number of fuel rods that can be loaded in the thermal zone is about 1185. Consequently, the neutron multiplication of the configuration with 21% enriched uranium fuel in the fast zone is enhanced by changing the position of the boron carbide and the natural uranium absorber rods, located between the fast and the thermal zones, to form an annular rather than a square arrangement. (author)

  18. Seat and seatbelt accommodation in fire apparatus: Anthropometric aspects.

    Science.gov (United States)

    Hsiao, Hongwei; Whitestone, Jennifer; Wilbur, Michael; Lackore, J Roger; Routley, J Gordon

    2015-11-01

    This study developed anthropometric information on U.S. firefighters to guide fire-apparatus seat and seatbelt designs and future standards development. A stratified sample of 863 male and 88 female firefighters across the U.S. participated in the study. The study results suggested 498 mm in width, 404 mm in depth, and 365-476 mm in height for seat pans; 429-522 mm in width and 542 mm in height for seat back; 871 mm in height for head support; a seat space of 733 mm at shoulder and 678 mm at hip; and a knee/leg clearance of 909 mm in fire truck cab. Also, 1520 mm of lap belt web effective length and 2828 mm of lap-and-shoulder belt web effective length were suggested. These data for fire-truck seats and seatbelts provide a foundation for fire apparatus manufacturers and standards committees to improve firefighter seat designs and seatbelt usage compliance. Published by Elsevier Ltd.

  19. Booster fans : some considerations for their usage in underground coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Gillies, S.; Slaughter, C. [Missouri Univ. of Science and Technology, Rolla, MO (United States); Calizaya, F. [Utah Univ., Salt Lake City, UT (United States); Wu, H.W. [Gillies Wu Mining Technology Pty Ltd., Brisbane, QLD (Australia)

    2010-07-01

    This paper reported on a study that investigated the conditions under which booster fans can be used safely and efficiently in underground coal mines. Booster fans are installed in series with a main surface fan and are used to boost the air pressure of the ventilation air passing through it. Several coal mining countries use booster fans, but in the United States, they are only used in metal/non-metal mines due to concerns of uncontrolled recirculation. This study investigated installations of booster fans in non-US underground coal mines where safe and efficient atmospheric conditions are achieved. The purpose was to collect reliable information on airway resistances and flow requirements typical in large US coal mines. The study showed that safe booster fan installations are found in both high and low gas conditions, and sometimes where workings are located at great depths. The interlocking systems within the booster fan can control the underground fans and avoid recirculation when surface fans are unexpectedly turned off. Another purpose of the study was to determine when booster fans become a more viable solution in coal mines due to increases in air requirements at higher production rates. It was concluded that a new fan selection algorithm to produce recirculation-free ventilation designs will be developed to enable US coal mine operators to develop ventilation designs to extract coal seams from depths greater than 1000 m. 17 refs., 1 fig.

  20. Ram booster

    Science.gov (United States)

    Brand, Vance D. (Inventor); Morgan, Walter Ray (Inventor)

    2011-01-01

    The present invention is a space launch system and method to propel a payload bearing craft into earth orbit. The invention has two, or preferably, three stages. The upper stage has rocket engines capable of carrying a payload to orbit and provides the capability of releasably attaching to the lower, or preferably, middle stage. Similar to the lower stage, the middle stage is a reusable booster stage that employs all air breathing engines, is recoverable, and can be turned-around in a short time between missions.

  1. Optimization of Aircraft Seat Cushion Fire Blocking Layers.

    Science.gov (United States)

    1983-03-01

    function of cost and weight, and the costs of labor involved in assembling a ccmposite seat cushion. The same classes of high char yield polymers that are...SEAT LATER DESIGN REPORT NRBBNBsg$$$$$$NN$$R$$$$$ SEAT DESIGN NUMBER: 009 LAYER NAME CODE NO. S MANUFACTURER 5 COST FACTORS . LABOR ...72621, 9096.. 7SS43. 73757. 77147. DELTA COSTS 0. 8340. 2922. 1136. 4327. ACOSOS in Iho..aS Of dollars. COST SUIRNY REPORT Re ....... VONR3 MORFA

  2. Seat Belt Use Intention among Brazilian Undergraduate Students

    OpenAIRE

    TORQUATO, RENATA; FRANCO, CLÁUDIO M. A; BIANCHI, ALESSANDRA

    2012-01-01

    The objectives of this study were to explore self-reported seat belt use and group differences in different scenarios in a Brazilian sample and research the variables related to it. 120 college students answered a questionnaire with variables from the theory of planned behavior in order to evaluate the intention of seat belt use among car occupants. Results indicated that attitude and intention were the variables that most contributed to explaining seat belt use. Intention was highly correlat...

  3. Proposed data acquisition system for the Fermilab Booster

    International Nuclear Information System (INIS)

    Bharadwaj, V.; Peggs, S.; Wu, G.; Saltmarsh, C.

    1991-01-01

    At present, studies involving the FNAL Booster (or in fact most accelerators) depend on knowing exactly what detector one has to look at and at what time. Because of this, most studies are done 'on-line' and involve looking for repetitive effects using a limited number of detectors. In this paper the authors propose to design a Booster Data Acquisition System (BDAQ) for the FNAL Booster. In essence this system consists of a large number of digitizers with circular memory buffers. After a machine cycle of interest, these buffers are frozen and then read out into a mass storage device. This paper discusses the hardware and software capabilities needed to make such a data acquisition system a powerful tool for doing accelerator physics studies and improving machine performance

  4. Study to develop improved fire resistant aircraft passenger seat materials

    Science.gov (United States)

    Duskin, F. E.; Schutter, K. J.; Sieth, H. H.; Trabold, E. L.

    1980-01-01

    The Phase 3 study of the NASA 'Improved Fire Resistant Aircraft Seat Materials' involved fire tests of improved materials in multilayered combinations representative of cushion configurations. Tests were conducted to determine their thermal, smoke, and fire resistance characteristics. Additionally, a 'Design Guideline' for Fire Resistant Passenger Seats was written outlining general seat design considerations. Finally, a three-abreast 'Tourist Class' passenger seat assembly fabricated from the most advanced fire-resistant materials was delivered.

  5. Rapid cycling superconducting booster synchrotron

    International Nuclear Information System (INIS)

    Dinev, D.; Agapov, N.; Butenko, A.

    2001-01-01

    The existing set of Nuclotron heavy ion sources, such as duoplasmatron, polarized deuteron, laser and electron beam ion sources permits to have ion beams over a wide range of masses. The main problem for us now is to gain high intensity of accelerator particles. It can be solved by means of multiturn injection of the low current beams into the booster, acceleration up to the intermediate energies, stripping and transferring into the main ring. A design study of this accelerator - the 250 MeV/Amu Nuclotron booster synchrotron at 1 Hz repetition rate and circumference of 84 m, has been completed. The lattice dipole and quadrupole magnets have an iron yoke coils, made of hollow superconductor, are cooled by two-phase Helium flow, as well as the Nuclotron magnets. (authors)

  6. AHF Booster Tracking with SIMPSONS.

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, D. E. (David E.); Neri, F. (Filippo)

    2002-01-01

    The booster lattice for the Advanced Hydrotest Facility at Los Alamos was tracked in 3-D with the program SIMPSONS, using the full, symplectic lattice from TEAPOT, using the full set of magnet and misalignment errors, as well as full space-charge effects. The only corrections included were a rough closed-orbit correction and chromaticity correction. The lattice was tracked for an entire booster cycle, from multi-turn injection through acceleration to the top energy of 4 GeV, approximately 99,000 turns. An initial injection intensity of 4x1Ol2, injected in 25 turns, resulted in a final intensity of 3 . 2 {approx} 1 0a' {approx}t 4 GeV. Results of the tracking, including emittance growth, particle loss, and particle tune distributions are presented.

  7. AHF Booster Tracking with SIMPSONS

    International Nuclear Information System (INIS)

    Johnson, D.E.; Neri, F.

    2002-01-01

    The booster lattice for the Advanced Hydrotest Facility at Los Alamos was tracked in 3-D with the program SIMPSONS, using the full, symplectic lattice from TEAPOT, using the full set of magnet and misalignment errors, as well as full space-charge effects. The only corrections included were a rough closed-orbit correction and chromaticity correction. The lattice was tracked for an entire booster cycle, from multi-turn injection through acceleration to the top energy of 4 GeV, approximately 99,000 turns. An initial injection intensity of 4x1Ol2, injected in 25 turns, resulted in a final intensity of 3 . 2 ∼ 1 0a' ∼t 4 GeV. Results of the tracking, including emittance growth, particle loss, and particle tune distributions are presented.

  8. Association between weight and risk of crash-related injuries for children in child restraints.

    Science.gov (United States)

    Zonfrillo, Mark R; Elliott, Michael R; Flannagan, Carol A; Durbin, Dennis R

    2011-12-01

    To determine the association between weight and the risk of injury in motor vehicle crashes (MVCs) for children 1 through 8 years of age who were using child restraints. This was a cross-sectional study of children 1 to 8 years of age in MVCs, in which cases from the National Automotive Sampling System Crashworthiness Data System were used. Abbreviated Injury Scale scores of ≥2 indicated clinically significant injuries. The National Automotive Sampling System Crashworthiness Data System study sample included 650 children 1 to 5 years of age in forward-facing child restraints who weighed 20 to 65 lb and 344 children 3 to 8 years of age in belt-positioning booster seats who weighed 30 to 100 lb. With adjustment for seating position, type of vehicle, direction of impact, crash severity, and vehicle model year, there was no association between absolute weight and clinically significant injuries in either age group (odds ratio: 1.17 [95% confidence interval: 0.96-1.42] for children 1-5 years of age in forward-facing child restraints and 1.22 [95% confidence interval: 0.96-1.55] for children 3-8 years of age in belt-positioning booster seats). The risk of clinically significant injuries was not associated with weight across a broad weight range in this sample of children in MVCs who were using child restraint systems. Parents should continue to restrain their children according to current recommendations from the American Academy of Pediatrics and the National Highway Traffic Safety Administration.

  9. Multi-leg Seat Inventory Control Based on EMSU and Virtual Bucket

    Directory of Open Access Journals (Sweden)

    Wei Fan

    2014-01-01

    Full Text Available Expected marginal seat revenue (EMSR is a well-known method for airline seat inventory control airlines. However, this method employs a static model to study the dynamic reservation process, and does not take into account the risk tolerance of policy makers. Expected marginal seat utility (EMSU replaces revenue by utility, which addresses the real situation of seat inventory control. However, there is still a lack of multi-leg seat control algorithms based on EMSU. Therefore, using EMSU and bucket algorithms, this paper applies the Markov decision-making process to simulate the flight reservation process and builds a dynamic multi-leg seat inventory control model. Experimental results validate the effectiveness of the proposed method.

  10. The Booster to AGS beam transfer fast kicker systems

    International Nuclear Information System (INIS)

    Zhang, W.; Bunicci, J.; Soukas, A.V.; Zhang, S.Y.

    1992-01-01

    The Brookhaven AGS Booster has a very successful commissioning period in June 1991. The third phase of that commissioning was a beam extraction test. The Booster extraction fast kicker (F3) deflected a 1.2 GeV proton beam from the Booster circulating orbit into the extraction septum aperture, partially down the extraction line to a temporary beam stop. Now, the Booster is committed to the AGS operations program for both heavy ion and proton beams. Thus, the Booster extraction and the corresponding AGS injection systems must operate routinely up to a pulse repetition frequency of 7.5 Hertz, and up to a beam energy of 1.5 Gev. The injection fast kicker is located in the A5 section of the AGS ring and is used to deflect the proton or heavy ion beam into its final AGS closed orbit. A distinctive feature of the AGS injection fast kicker modulators is the tail-bitting function required for proton beam injection. This enables the system to produce a fast current fall time to go along with the high current pulse amplitude with a fast rise time. The AGS injection fast kicker system has three pulse modulators, and each modulator consists of two thyratrons. The main PFN thyratrons switch on the current, and the tail bitting thyratrons are used to force the magnet current to decrease rapidly. Two digital pulse delay generators are used to align the main thyratrons and the tail bitting thyratrons respectively. The system has been tested and installed. The final commissioning of the Booster to AGS beam transfer line and injection is currently being undertaken. In this article, the system design, realization techniques and performance data will be presented

  11. A rookie's guide to Booster operations. Booster technical note no. 231

    Energy Technology Data Exchange (ETDEWEB)

    Zeno, K. [Brookhaven National Lab. (BNL), Upton, NY (United States). Alternating Gradient Synchrotron Dept.

    1998-09-29

    The purpose of the Booster is to act as an injector for the AGS. It accelerates both protons and other ions. Proton acceleration is distinguished from the acceleration of other ions for several reasons. First, the experimental physics associated with protons, called High Energy Physics is different than that associated with other Ions, called Heavy Ion Physics. From the machine perspective, the process of injection of so called Heavy Ions (ions which are not protons), is distinctly different, from that of protons. A different preinjector, or injector for the Booster, is used for each case. For Protons, a 200 MeV Linear accelerator (The Linac) serves as a preinjector; for Heavy Ions, the Tandem Van De Graaf (The Tandem) is the preinjector. An attribute of the circulating beam which determines to a large degree what problems and what type of machine setup is involved is the beam intensity. The author's focus in this guide is on trying to convey the knowledge and experience involved in the operation of the Booster. Many of the problems encountered can be traced back to equipment failures, often power supplies. Although diagnostics are used, there can also be issues with the controls system itself. Problems with the controls system and prevent fixing or even finding a problem with a machine. The issue of improving a machines' performance can often involve trial and error and observations. The hard part is finding the relationships between things in the day to day operation of the machine. Abstractions about physics, information about controls and instrumentation, and purely empirical observations of how the machine behaves are all part of it.

  12. Kineto-dynamic design optimisation for vehicle-specific seat-suspension systems

    Science.gov (United States)

    Shangguan, Wen-Bin; Shui, Yijie; Rakheja, Subhash

    2017-11-01

    Designs and analyses of seat-suspension systems are invariably performed considering effective vertical spring rate and damping properties, while neglecting important contributions due to kinematics of the widely used cross-linkage mechanism. In this study, a kineto-dynamic model of a seat-suspension is formulated to obtain relations for effective vertical suspension stiffness and damping characteristics as functions of those of the air spring and the hydraulic damper, respectively. The proposed relations are verified through simulations of the multi-body dynamic model of the cross-linkage seat-suspension in the ADAMS platform. The validity of the kineto-dynamic model is also demonstrated through comparisons of its vibration transmission response with the experimental data. The model is used to identify optimal air spring coordinates to attain nearly constant natural frequency of the suspension, irrespective of the seated body mass and seated height. A methodology is further proposed to identify optimal damping requirements for vehicle-specific suspension designs to achieve minimal seat effective amplitude transmissibility (SEAT) and vibration dose value (VDV) considering vibration spectra of different classes of earthmoving vehicles. The shock and vibration isolation performance potentials of the optimal designs are evaluated under selected vehicle vibration superimposed with shock motions. Results show that the vehicle-specific optimal designs could provide substantial reductions in the SEAT and VDV values for the vehicle classes considered.

  13. Wheelchair Seating Assessment and Intervention: A Comparison Between Telerehabilitation and Face-to-Face Service

    Science.gov (United States)

    Barlow, Ingrid G; Liu, Lili; Sekulic, Angela

    2009-01-01

    This study compared outcomes of wheelchair seating and positioning interventions provided by telerehabilitation (n=10) and face-to-face (n=20; 10 in each of two comparison groups, one urban and one rural). Comparison clients were matched to the telerehabilitation clients in age, diagnosis, and type of seating components received. Clients and referring therapists rated their satisfaction and identified if seating intervention goals were met. Clients recorded travel expenses incurred or saved, and all therapists recorded time spent providing service. Wait times and completion times were tracked. Clients seen by telerehabilitation had similar satisfaction ratings and were as likely to have their goals met as clients seen face-to-face; telerehabilitation clients saved travel costs. Rural referring therapists who used telerehabilitation spent more time in preparation and follow-up than the other groups. Clients assessed by telerehabilitation had shorter wait times for assessment than rural face-to-face clients, but their interventions took as long to complete. PMID:25945159

  14. Using in-depth investigations to identify transportation safety issues for wheelchair-seated occupants of motor vehicles.

    Science.gov (United States)

    Schneider, Lawrence W; Klinich, Kathleen D; Moore, Jamie L; MacWilliams, Joel B

    2010-04-01

    In-depth investigations of motor-vehicle crashes involve detailed inspection, measurement, and photodocumentation of vehicle exterior and interior damage, evidence of belt-restraint use, and evidence of occupant contacts with the vehicle interior. Results of in-depth investigations thereby provide the most objective way to identify current and emerging injury problems and issues in occupant safety and crash protection, and provide important feedback on the real-world performance of the latest restraint-system and vehicle crashworthiness technologies. To provide an objective understanding of real-world transportation safety issues for wheelchair-seated travelers, the University of Michigan Transportation Research Institute (UMTRI) has been conducting and assembling data from in-depth investigations of motor-vehicle crashes and non-crash adverse moving-vehicle incidents, such as emergency vehicle braking, turning, and swerving, in which there was at least one vehicle occupant sitting in a wheelchair. The results of 39 investigations involving 42 wheelchair-seated occupants have been assembled and entered into a wheelchair-occupant crash/injury database. In addition, a biomechanical analysis of each case has been performed to identify key safety issues for wheelchair-seated travelers. The wheelchairs of 34 of the 42 occupants who were seated in wheelchairs while traveling in motor vehicles were effectively secured by either a four-point, strap-type tiedown system or a docking securement device, and all but one of these properly secured wheelchairs remained in place during the crash or non-collision event. However, 30 of the 42 occupants were improperly restrained, either because of non-use or incomplete use of available belt restraints, or because the belt restraints were improperly positioned on the occupant's body. Twenty-six of the 42 occupants sustained significant injuries and 10 of these occupants died as a direct result of injuries sustained, or from

  15. Classroom Seating Considerations for 21st Century Students and Faculty

    Science.gov (United States)

    Harvey, Eugene J.; Kenyon, Melaine C.

    2013-01-01

    This quantitative, cross-sectional research study explored students' perceptions of five different seating styles within typical classrooms in an urban public higher education institution. The five seating styles included: modern mobile chairs, tablet arm chairs, fixed tiered seating with tablet arms, rectangle tables with standard chairs, and…

  16. Child Passenger Safety (A Cup of Health with CDC)

    Centers for Disease Control (CDC) Podcasts

    Proper installation and use of car seats and booster seats for child passengers can save their lives. CDC recommends drivers ensure children are always buckled up. In this podcast, Bethany West discusses how to keep young passengers as safe as possible.

  17. MACRO MODEL OF SEAT BELT USE BY CAR DRIVERS AND PASSENGERS

    Directory of Open Access Journals (Sweden)

    Kazimierz JAMROZ

    2013-12-01

    Full Text Available The article presents some problems of seat belt use by car drivers and passengers. It looks in particular at seat belt use and effectiveness in selected countries. Next, factors of seat belt use are presented and methodology of model development. A macro model of seat belt use is presented based on data from around fifty countries from different continents.

  18. International survey of seat belt use exemptions.

    Science.gov (United States)

    Weiss, H; Sirin, H; Levine, J A; Sauber, E

    2006-08-01

    Substantial evidence of seatbelt efficacy has been shown by several studies, and it is widely recommended that motor vehicle occupants use properly fitted seat belts. However, some (but a heretofore unknown number of) countries with national seat belt laws permit various exemptions which may lower use rates. The aim of this study was to survey the variety of exemptions to national seat belt laws. This investigation relied on identifying respondents from national traffic safety agencies, other governmental and non-governmental organizations, Internet searches, personal contacts, and other sources. Questionnaires were deployed through a web based survey supplemented by email and postal versions. Responses were received from 30 countries of which 28 (93.7%) had a national seat belt law. About two thirds (63.7%) of the 28 national laws applied to both front and back seat passengers. The leading exemption types included vehicles made before a certain year (n = 13), antique vehicles (n = 12), military vehicles (n = 11), buses (n = 9), and emergency vehicles (n = 8). Most responding countries reported one or more specific categories of individuals as exempt including those with medical exemptions (n = 20), taxi drivers (n = 11), police (n = 9), emergency medical personnel (n = 8), physically disabled people (n = 6), and pregnant women (n = 6). Out of 26 responses to the question regarding current level of enforcement, 42.3% felt enforcement was "very good or good" and 57.7% characterized it as "fair or poor". This study represents one of the largest international traffic law surveys reported. Most national seatbelt laws offer perilous exemptions to a broad array of vehicle types and road user groups. These findings, coupled with concern over the level of enforcement in the majority of countries surveyed, suggest that international road safety efforts have a long way to go to improve coverage and enforcement of national seat belt laws.

  19. The effects of seat belt legislation on road traffic injuries.

    Science.gov (United States)

    Trinca, G W; Dooley, B J

    1977-04-01

    The compulsory wearing of seat belts, first introduced in the world in Victoria in 1970, has effectively reduced the number of deaths and injuries by approximately one-third for car occupants involved in motor vehicle crashes. Initially, the legislation did not apply to children under the age of eight years, but in 1975 a further law was introduced banning children from the front seat of any vehicle unless properly harnessed. Seat belts offer the best protection for front seat drivers and passengers involved in frontal impacts, but offer less protection to the recipient of a side impact. Ten per cent of car occupants admitted to hospital after a frontal impact show injuries, mostly minor, directly attibutable to the wearing of seat belts.

  20. Thermal comfort of seats as visualized by infrared thermography.

    Science.gov (United States)

    Sales, Rosemary Bom Conselho; Pereira, Romeu Rodrigues; Aguilar, Maria Teresa Paulino; Cardoso, Antônio Valadão

    2017-07-01

    Published studies that deal with the question of how the temperature of chair seats influences human activities are few, but the studies considering such a factor, a function of the type of material, could contribute to improvements in the design of chairs. This study evaluates seat temperatures of 8 types of chairs made of different materials. The parts of the furniture that people come into contact with, and the thermal response of the material to heating and cooling have been evaluated. Infrared thermography was used for this, as it is a non-contact technique that does not present any type of risk in the measurement of temperatures. Seats made of synthetic leather (leatherette), wood and polyester fabric were found to have the highest temperatures, and the plywood seat showed the lowest. The study has also revealed that thermography can contribute to studies of thermal comfort of chair seats in addition to determining the most suitable material. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Body height and arterial pressure in seated and supine young males during +2 G centrifugation

    DEFF Research Database (Denmark)

    Arvedsen, Sine K.; Eiken, Ola; Kölegård, Roger

    2015-01-01

    by the use of a human centrifuge would increase mean arterial pressure (MAP) more in tall than in short males in the seated position. In short (162-171cm, n=8) and tall (194-203cm, n=10) healthy males (18-41yr), brachial arterial pressure, heart rate (HR) and cardiac output were measured during +2G...... centrifugation, while they were seated upright with the legs kept horizontal (+2Gz). In a separate experiment, the same measurements were done with the subjects supine (+2Gx). During +2Gz MAP increased in the short (22±2 mmHg, P 

  2. Aortic ruptures in seat belt wearers.

    Science.gov (United States)

    Arajärvi, E; Santavirta, S; Tolonen, J

    1989-09-01

    Several investigations have indicated that rupture of the thoracic aorta is one of the leading causes of immediate death in victims of road traffic accidents. In Finland in 1983, 92% of front-seat passengers were seat belt wearers on highways and 82% in build-up areas. The mechanisms of rupture of the aorta have been intensively investigated, but the relationship between seat belt wearing and injury mechanisms leading to aortic rupture is still largely unknown. This study comprises 4169 fatally injured victims investigated by the Boards of Traffic Accident Investigation of Insurance Companies during the period 1972 to 1985. Chest injuries were recorded as the main cause of death in 1121 (26.9%) victims, 207 (5.0%) of those victims having worn a seat belt. Aortic ruptures were found at autopsy in 98 victims and the exact information of the location of the aortic tears was available in 68. For a control group, we analyzed 72 randomly chosen unbelted victims who had a fatal aortic rupture in similar accidents. The location of the aortic rupture in unbelted victims was more often in the ascending aorta, especially in drivers, whereas in seat belt wearers the distal descending aorta was statistically more often ruptured, especially in right-front passengers (p less than 0.05). The steering wheel predominated statistically as the part of the car estimated to have caused the injury in unbelted victims (37/72), and some interior part of the car was the most common cause of fatal thoracic impacts in seat belt wearers (48/68) (p less than 0.001). The mechanism of rupture of the aorta in the classic site just distal to the subclavian artery seems to be rapid deceleration, although complex body movements are also responsible in side impact collisions. The main mechanism leading to rupture of the ascending aorta seems to be severe blow to the bony thorax. This also often causes associated thoracic injuries, such as heart rupture and sternal fracture. Injuries in the ascending

  3. FNAL Booster intensity, extraction, and synchronization control for collider operation

    International Nuclear Information System (INIS)

    Ducar, R.J.; Lackey, J.R.; Tawzer, S.R.

    1987-03-01

    Booster operation for collider physics is considerably different than for fixed target operation. Various scenarios for collider physics, machine studies, and P-Bar targeting may require that the intensity vary from 5E10 PPP to 3E12 PPP at a 15 Hertz machine cycle rate. In addition to the normal Booster single turn extraction mode, collider operations require that the Booster inject into the Main Ring a small number of beam bunches for coalescing into a single high intensity bunch. These bunches must be synchronized such that the center bunch arrives in the RF bucket which corresponds to the zero phase of the coalescing cavity. The system implemented has the ability to deliver a precise fraction of the available 84 Booster beam bunches to Main Ring or to the P-Bar Debuncher via the newly installed AP-4 beam line for tune-up and studies. It is required that all of the various intensity and extraction scenarios be accommodated with minimal operator intervention

  4. Car safety seat usage and selection among families attending University Hospital Limerick

    LENUS (Irish Health Repository)

    Scully, P

    2016-05-01

    The safest way for children to travel within a car is by provision of a weight-appropriate safety-seat. To investigate this, we conducted a cross-sectional study of adult parents who had children under 12 years, and collected information related to: car use, safety-seat legislation, and type of safety-seat employed. Data were reviewed on 120 children from 60 respondents. Ninety-eight (81.7%) children were transported daily by car. Forty-eight (81.4%) respondents were aware that current safety-seat legislation is based on the weight of the child. One hundred and seven (89.9%) children were restrained during travel using a car safety-seat. One hundred and two (96.2%) safety seats were newly purchased, installed in 82.3% (88) cases by family members with installation instructions fully read in 58 (55.2%) cases. Ninety-nine (83.2%) children were restrained using an appropriate safety-seat for their weight. The results show that four out of five families are employing the most appropriate safety-seat for their child, so providing an effective mechanism to reduce car-related injury. However, the majority of safety-seats are installed by family members, which may have child safety consequences.

  5. Real-world adjustments of driver seat and head restraint in Saab 9-3 vehicles.

    Science.gov (United States)

    Carlsson, Anna; Pipkorn, Linda; Kullgren, Anders; Svensson, Mats

    2017-05-19

    Whiplash-associated disorder (WAD), commonly denoted whiplash injury, is a worldwide problem. These injuries occur at relatively low changes of velocity (typically whiplash injury than males.  Improved seat design is the prevailing means of increasing the protection of whiplash injury for occupants in rear impacts. Since 1997, more advanced whiplash protection systems have been introduced on the market, the Saab Active Head Restraint (SAHR) being one of the most prominent. The SAHR-which is height adjustable-is mounted to a pressure plate in the seatback by means of a spring-resisted link mechanism.  Nevertheless, studies have shown that seats equipped with reactive head restraints (such as the SAHR) have a very high injury-reducing effect for males (∼60-70%) but very low or no reduction effect for females. One influencing factor could be the position of the head restraint relative to the head, because a number of studies have reported that adjustable head restraints often are incorrectly positioned by drivers.  The aim was to investigate how female and male Saab drivers adjust the seat in the car they drive the most. The seated positions of drivers in stationary conditions have been investigated in a total of 76 volunteers (34 females, 42 males) who participated in the study. Inclusion criteria incorporated driving a Saab 9-3 on a regularly basis. The majority of the volunteers (89%) adjusted the head restraint to any of the 3 uppermost positions and as many as 59% in the top position.  The average vertical distance between the top of the head and the top of the head restraint (offset) increase linearly with increasing statures, from an average of -26 mm (head below the head restraint) for small females to an average of 82 mm (head above the head restraint) for large males. On average, the offset was 23 mm for females, which is within a satisfactory range and in accordance with recommendations; the corresponding value for males was 72 mm.

  6. Space shuttle with common fuel tank for liquid rocket booster and main engines (supertanker space shuttle)

    Science.gov (United States)

    Thorpe, Douglas G.

    1991-01-01

    An operation and schedule enhancement is shown that replaces the four-body cluster (Space Shuttle Orbiter (SSO), external tank, and two solid rocket boosters) with a simpler two-body cluster (SSO and liquid rocket booster/external tank). At staging velocity, the booster unit (liquid-fueled booster engines and vehicle support structure) is jettisoned while the remaining SSO and supertank continues on to orbit. The simpler two-bodied cluster reduces the processing and stack time until SSO mate from 57 days (for the solid rocket booster) to 20 days (for the liquid rocket booster). The areas in which liquid booster systems are superior to solid rocket boosters are discussed. Alternative and future generation vehicles are reviewed to reveal greater performance and operations enhancements with more modifications to the current methods of propulsion design philosophy, e.g., combined cycle engines, and concentric propellant tanks.

  7. Assessment of Rail Seat Abrasion Patterns and Environment

    Science.gov (United States)

    2012-05-01

    Rail seat abrasion (RSA) of concrete ties is manifested by the loss of material under the rail seat area and, in extreme cases, results in loss of rail clip holding power, reverse rail cant, and gauge widening. RSA was measured in several curves on t...

  8. Seat-belt message and the law?

    Science.gov (United States)

    Sengupta, S K; Patil, N G; Law, G

    1989-09-01

    This paper attempts to draw together available information on the use of seat belts, one of the most important safety devices for a person in a car. Considering the high rate of mortality and morbidity due to road traffic accidents in Papua New Guinea the authors strongly feel that seat-belt usage should be made compulsory. When one looks at the history of the implementation of such a successful countermeasure in other countries it seems that legislation is the only answer.

  9. Vibration control of an energy regenerative seat suspension with variable external resistance

    Science.gov (United States)

    Ning, Donghong; Sun, Shuaishuai; Du, Haiping; Li, Weihua; Zhang, Nong

    2018-06-01

    In this paper, an energy regenerative seat suspension with a variable external resistance is proposed and built, and a semi-active controller for its vibration control is also designed and validated. The energy regenerative seat suspension is built with a three-phase generator and a gear reducer, which are installed in the scissors structure centre of the seat suspension, and the vibration energy is directly harvested from the rotary movement of suspension's scissors structure. The electromagnetic torque of the semi-active seat suspension actuator is controlled by an external variable resistor. An integrated model including the seat suspension's kinematics and the generator is built and proven to match the test result very well. A simplified experimental phenomenon model is also built based on the test results for the controller design. A state feedback H∞ controller is proposed for the regenerative seat suspension's semi-active vibration control. The proposed regenerative seat suspension and its controller are validated with both simulations and experiments. A well-tuned passive seat suspension is applied to evaluate the regenerative seat's performance. Based on ISO 2631-1, the frequency-weighted root mean square (FW-RMS) acceleration of the proposed seat suspension has a 22.84% reduction when compared with the passive one, which indicates the improvement of ride comfort. At the same time, the generated RMS power is 1.21 W. The proposed regenerative seat suspension can greatly improve the driver's ride comfort and has the potential to be developed to a self-powered semi-active system.

  10. Sliding and pressure evaluation on conventional and V-shaped seats of reclining wheelchairs for stroke patients with flaccid hemiplegia: a crossover trial

    Directory of Open Access Journals (Sweden)

    Chen Chi-Myn

    2011-07-01

    Full Text Available Abstract Background Reclining wheelchairs are commonly used to transport elderly stroke patients in Taiwan. However, there is concern that the patient's body in the wheelchair often slides forward when they return to a seated position, increasing the sitting pressure. Therefore, a novel reclining wheelchair with an ergonomic "V-Seat" was designed to prevent forward sliding and pressure sores. The use of these reclining chairs by stroke patients has not yet been studied. Thus, we investigated the effects of V-shaped and conventional seats in reclining wheelchairs on the extent of forward sliding and on the sitting pressure of stroke patients with flaccid hemiplegia and of able-bodied elders. Methods We recruited 13 able-bodied elders and 11 stroke patients with flaccid hemiplegia and performed 5 reclining cycles in both types of wheelchair. The amount of sliding along the backrest (BS plane and the seat (SS plane, the mean sitting pressure (MP, and the sacral peak pressure (SPP of the subjects were recorded. We used the Wilcoxon signed-rank test to compare the BS, SS, MP, and SPP in wheelchairs with conventional and V-shaped seats, and we used the Wilcoxon rank sum test to compare the differences in BS and SS between stroke patients and able-bodied elders in both types of reclining wheelchair. Results The BS, SS, and SPP of stroke patients were significantly lower in the wheelchairs with V-shaped seats than in conventional wheelchairs in most comparisons; however, the BS of able-bodied elders was higher in V-shaped seats than in conventional seats. The SS and SPP of stroke patients were significantly higher than those of able-bodied elders in both types of reclining wheelchair, and the BS of stroke patients was significantly higher than that of able-bodied elders only in conventional reclining wheelchairs. Conclusions The use of V-shaped seats in reclining wheelchairs can help reduce the forward sliding and sacral peak pressure of stroke patients

  11. Linac boosters for electrostatic machines

    International Nuclear Information System (INIS)

    Ben-Zvi, I.; Brookhaven National Lab., Upton, NY

    1990-01-01

    A survey of linacs which are used as boosters to electrostatic accelerators is presented. Machines both operating and under construction, copper and superconducting, are reviewed. The review includes data on the accelerating structures, performance, rf and control, beam optics, budget, vacuum and cryogenics. (orig.)

  12. JAERI tandem-accelerator and tandem-booster

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, Tadashi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1998-03-01

    In 1982, aiming at the new development of atomic energy research, the tandem accelerator of Japan Atomic Energy Research Institute (JAERI) was installed. In fiscal year 1993, the superconducting boosters which can increase the ion energy by up to 4 times were added, and the research in the region below 1000 MeV became possible. Those are electrostatic type accelerators which are easy to be used especially in basic research field, and are useful for future research. The tandem accelerator has been operated while maintaining the first class performance as the accelerator for various kinds of heavy ion beam. It has the special shape among electrostatic type accelerators, and is excellent in the easiness of control and stability. The main particulars of the tandem accelerator are shown. As for the ion sources of the tandem accelerator, three cesium sputter type ion sources are installed on two high voltage stands. The kinds of the ions which can be accelerated are mainly negative ions. As the improvement, electron cyclotron resonance (ECR) ion sources are expected to be adopted. As for the tandem boosters, the 1/4 wavelength type resonance hollow cylinder was adopted. The constitution of the tandem boosters is explained. The way of utilizing the tandem accelerator system and the aim for hereafter are reported. (K.I.)

  13. Seat headrest-incorporated personalized ventilation: Thermal comfort and inhaled air quality

    DEFF Research Database (Denmark)

    Melikov, Arsen Krikor; Ivanova, T.; Stefanova, G.

    2012-01-01

    inhaled by the manikin was measured and used to assess the clean air supply efficiency of the SHPV. The response of 35 subjects was collected to examine thermal comfort with the SHPV. The subjects participated in 3 experiments at personalized air temperature and room air temperature of 22/20 °C, 23/23 °C......The performance of personalized ventilation with seat headrest-mounted air supply terminal devices (ATD), named seat headrest personalized ventilation (SHPV), was studied. Physical measurements using a breathing thermal manikin were taken to identify its ability to provide clean air to inhalation...... depending on design, shape, size and positioning of the ATD, flow rate and temperature of personalized air, room temperature, clothing thermal insulation of the manikin, etc. Tracer gas was mixed with the room air. The air supplied by the SHPV was free of tracer gas. Tracer gas concentration in the air...

  14. 47 CFR 74.1290 - FM translator and booster station information available on the Internet.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 4 2010-10-01 2010-10-01 false FM translator and booster station information... DISTRIBUTIONAL SERVICES FM Broadcast Translator Stations and FM Broadcast Booster Stations § 74.1290 FM translator and booster station information available on the Internet. The Media Bureau's Audio Division...

  15. Hemodynamic responses to seated and supine lower body negative pressure - Comparison with +Gz acceleration

    Science.gov (United States)

    Polese, Alvese; Sandler, Harold; Montgomery, Leslie D.

    1992-01-01

    The hemodynamic responses to LBNP in seated subjects and in subjects in supine body positions were compared and were correlated with hemodynamic changes which occurred during a simulated (by centrifugation) Shuttle reentry acceleration with a slow onset rate of 0.002 G/s and during gradual onset exposures to +3 Gz and +4 Gz. Results demonstrate that seated LBNP at a level of -40 mm Hg can serve as a static simulator for changes in the heart rate and in mean blood pressure induced by gradual onset acceleration stress occurring during Shuttle reentry. The findings also provide a rationale for using LBNP during weightlessness as a means of imposing G-loading on the circulation prior to reentry.

  16. 78 FR 29062 - Signal Booster Rules

    Science.gov (United States)

    2013-05-17

    ... number of FCC rules concerning signal boosters for consumer and industrial use. This document corrects a... chapter; the Maritime Services (ship earth station devices only) pursuant to part 80 of this chapter; and...

  17. Advanced Booster Composite Case/Polybenzimidazole Nitrile Butadiene Rubber Insulation Development

    Science.gov (United States)

    Gentz, Steve; Taylor, Robert; Nettles, Mindy

    2015-01-01

    The NASA Engineering and Safety Center (NESC) was requested to examine processing sensitivities (e.g., cure temperature control/variance, debonds, density variations) of polybenzimidazole nitrile butadiene rubber (PBI-NBR) insulation, case fiber, and resin systems and to evaluate nondestructive evaluation (NDE) and damage tolerance methods/models required to support human-rated composite motor cases. The proposed use of composite motor cases in Blocks IA and II was expected to increase performance capability through optimizing operating pressure and increasing propellant mass fraction. This assessment was to support the evaluation of risk reduction for large booster component development/fabrication, NDE of low mass-to-strength ratio material structures, and solid booster propellant formulation as requested in the Space Launch System NASA Research Announcement for Advanced Booster Engineering Demonstration and/or Risk Reduction. Composite case materials and high-energy propellants represent an enabling capability in the Agency's ability to provide affordable, high-performing advanced booster concepts. The NESC team was requested to provide an assessment of co- and multiple-cure processing of composite case and PBI-NBR insulation materials and evaluation of high-energy propellant formulations.

  18. 75 FR 30775 - Availability of Seats for the Monitor National Marine Sanctuary Advisory Council

    Science.gov (United States)

    2010-06-02

    ..., Recreational Diving seat, Education seat, Archaeological Research seat, Maritime Museum seat, Youth seat, and... by NOAA's Office of National Marine Sanctuaries. It is one of 13 sanctuaries and protects the wreck..., Recreational Diving, the US Navy, Virginia and North Carolina Department of Historic Resources, the National...

  19. MEASUREMENTS AND MODELING OF EDDY CURRENT EFFECTS IN BNL'S AGS BOOSTER

    International Nuclear Information System (INIS)

    BROWN, K.A.; AHRENS, L.; GARDNER, C.; GLENN, J.W.; HARVEY, M.; MENG, W.; ZENO, K.

    2006-01-01

    Recent beam experiments at BNL's AGS Booster have enabled us to study in more detail the effects of eddy currents on the lattice structure and our control over the betatron tune. The Booster is capable of operating at ramp rates as high as 9 T/sec. At these ramp rates eddy currents in the vacuum chambers significantly alter the fields and gradients seen by the beam as it is accelerated. The Booster was designed with these effects in mind and to help control the field uniformity and linearity in the Booster Dipoles special vacuum chambers were designed with current windings to negate the affect of the induced eddy currents. In this report results from betatron tune measurements and eddy current simulations will be presented. We will then present results from modeling the accelerator using the results of the magnetic field simulations and compare these to the measurements

  20. Tdap Booster Requirements for Secondary Schools

    Science.gov (United States)

    ... Experts State Information Tdap booster requirements for secondary schools State Td or Tdap Mandate for Sec School ... Checklists Standing Orders Storage & Handling Talking with Parents Temperature Logs Top Handouts Translations Vaccine Index >> view all ...

  1. Tracking study of hadron collider boosters

    Energy Technology Data Exchange (ETDEWEB)

    Machida, S.; Bourianoff, G.; Huang, Y.; Mahale, N.

    1992-07-01

    A simulation code SIMPSONS (previously called 6D-TEASE T) of single- and multi-particle tracking has been developed for proton synchrotrons. The 6D phase space coordinates are calculated each time step including acceleration with an arbitrary ramping curve by integration of the rf phase. Space-charge effects are modelled by means of the Particle In Cell (PIC) method. We observed the transverse emittance growth around the injection energy of the Low Energy Booster (LEB) of the Superconducting Super Collider (SSC) with and without second harmonic rf cavities which reduce peak line density. We also employed the code to see the possible transverse emittance deterioration around the transition energy in the Medium Energy Booster (MEB) and to estimate the emittance dilution due to an injection error of the MEB.

  2. Injection and transfer lines of the PS Booster

    CERN Multimedia

    Photographic Service

    1972-01-01

    In the foreground is the vacuum chamber for the 50 MeV proton beam coming from the Linac. The tank held by white frames houses the "Vertical Distributor", which deflects the Linac beam to the levels of the Booster's 4 superposed rings. After acceleration in the Booster, originally to 800 MeV, today to 1.4 GeV, the beams from the 4 rings are combined in the vertical plane and transfered to the 26 GeV PS. The "Recombination Line", intersecting the injection line, crosses the picture from left to right.

  3. Design study of CEPC Alternating Magnetic Field Booster

    CERN Document Server

    Bian, T; Cai, Y; Cui, X; Gao, J; Koratzinos, M; Su, F; Wang, D; Wang, Y; Xiao, M; Zhang, C

    2017-01-01

    The CEPC is a next generation circular e+e- collider proposed by China. The design of the full energy booster ring of the CEPC is especially challenging. The ejected beam energy is 120 GeV, but that of the injected beam is only 6 GeV. In a conventional approach, the low magnetic field of the main dipole magnets creates problems. We propose operating the booster ring as a large wiggler at low beam energies and as a normal ring at high energies to avoid the problem of very low dipole magnet fields.

  4. The Surprising Impact of Seat Location on Student Performance

    Science.gov (United States)

    Perkins, Katherine K.; Wieman, Carl E.

    2005-01-01

    Every physics instructor knows that the most engaged and successful students tend to sit at the front of the class and the weakest students tend to sit at the back. However, it is normally assumed that this is merely an indication of the respective seat location preferences of weaker and stronger students. Here we present evidence suggesting that in fact this may be mixing up the cause and effect. It may be that the seat selection itself contributes to whether the student does well or poorly, rather than the other way around. While a number of studies have looked at the effect of seat location on students, the results are often inconclusive, and few, if any, have studied the effects in college classrooms with randomly assigned seats. In this paper, we report on our observations of a large introductory physics course in which we randomly assigned students to particular seat locations at the beginning of the semester. Seat location during the first half of the semester had a noticeable impact on student success in the course, particularly in the top and bottom parts of the grade distribution. Students sitting in the back of the room for the first half of the term were nearly six times as likely to receive an F as students who started in the front of the room. A corresponding but less dramatic reversal was evident in the fractions of students receiving As. These effects were in spite of many unusual efforts to engage students at the back of the class and a front-to-back reversal of seat location halfway through the term. These results suggest there may be inherent detrimental effects of large physics lecture halls that need to be further explored.

  5. Spatial correction factors for YALINA Booster facility loaded with medium and low enriched fuels

    International Nuclear Information System (INIS)

    Talamo, A.; Gohar, Y.; Bournos, V.; Fokov, Y.; Kiyavitskaya, H.; Routkovskaya, C.

    2012-01-01

    The Bell and Glasstone spatial correction factor is used in analyses of subcritical assemblies to correct the experimental reactivity as function of the detector position. Besides the detector position, several other parameters affect the correction factor: the energy weighting function of the detector, the detector size, the energy-angle distribution of source neutrons, and the reactivity of the subcritical assembly. This work focuses on the dependency of the correction factor on the detector material and it investigates the YALINA Booster subcritical assembly loaded with medium (36%) and low (10%) enriched fuels. (authors)

  6. Spatial correction factors for YALINA Booster facility loaded with medium and low enriched fuels

    Energy Technology Data Exchange (ETDEWEB)

    Talamo, A.; Gohar, Y. [Argonne National Laboratory, 9700 S. Cass Ave, Argonne, IL 60439 (United States); Bournos, V.; Fokov, Y.; Kiyavitskaya, H.; Routkovskaya, C. [Joint Inst. for Power and Nuclear Research-Sosny, 99 Academician A.K.Krasin Str, Minsk 220109 (Belarus)

    2012-07-01

    The Bell and Glasstone spatial correction factor is used in analyses of subcritical assemblies to correct the experimental reactivity as function of the detector position. Besides the detector position, several other parameters affect the correction factor: the energy weighting function of the detector, the detector size, the energy-angle distribution of source neutrons, and the reactivity of the subcritical assembly. This work focuses on the dependency of the correction factor on the detector material and it investigates the YALINA Booster subcritical assembly loaded with medium (36%) and low (10%) enriched fuels. (authors)

  7. Development of a Methodology to Gather Seated Anthropometry in a Microgravity Environment

    Science.gov (United States)

    Rajulu, Sudhakar; Young, Karen; Mesloh, Miranda

    2009-01-01

    The Constellation Program's Crew Exploration Vehicle (CEV) is required to accommodate the full population range of crewmembers according to the anthropometry requirements stated in the Human-Systems Integration Requirement (HSIR) document (CxP70024). Seated height is one of many critical dimensions of importance to the CEV designers in determining the optimum seat configuration in the vehicle. Changes in seated height may have a large impact to the design, accommodation, and safety of the crewmembers. Seated height can change due to elongation of the spine when crewmembers are exposed to microgravity. Spinal elongation is the straightening of the natural curvature of the spine and the expansion of inter-vertebral disks. This straightening occurs due to fluid shifts in the body and the lack of compressive forces on the spinal vertebrae. Previous studies have shown that as the natural curvature of the spine straightens, an increase in overall height of 3% of stature occurs which has been the basis of the current HSIR requirements. However due to variations in the torso/leg ratio and impact of soft tissue, data is nonexistent as to how spinal elongation specifically affects the measurement of seated height. In order to obtain this data, an experiment was designed to collect spinal elongation data while in a seated posture in microgravity. The purpose of this study was to provide quantitative data that represents the amount of change that occurs in seated height due to spinal elongation in microgravity environments. Given the schedule and budget constraints of ISS and Shuttle missions and the uniqueness of the problem, a methodology had to be developed to ensure that the seated height measurements were accurately collected. Therefore, simulated microgravity evaluations were conducted to test the methodology and procedures of the experiment. This evaluation obtained seat pan pressure and seated height data to a) ensure that the lap restraint provided sufficient

  8. Joint overbooking and seat allocation for fare families

    DEFF Research Database (Denmark)

    Hjorth, Robert; Fiig, Thomas; Bondoux, Nicolas

    2016-01-01

    Revenue Management Systems (RMS) traditionally solve the seat allocation problem separately from the overbooking problem. Overbooking is managed by inflating the authorization levels obtained from seat allocation by various heuristics. This approach although suboptimal, is necessitated because...... independent demand model, which is readily solved. The resulting availability control can easily by implemented in existing RMS...

  9. Design and Evaluation Methods for Optimizing Ejection Seat Cushions for Comfort and Safety

    Science.gov (United States)

    1977-02-01

    buttocks to the seat cushion or seat pan. Kohara , a Japaners Investigator discussed the problems of seating comfort and the measuren.ent of buttock/seat...loads In an unpublished report in 1965 (23) and subsequently In a magazine article In 1966 (24). Kohara was able to weasure pressures by means of...Isolation. Kohara has also studied the vibration Isolation requirements in high speed trains (23, 2’). Howeveri the seat cushion has been used only rarely in

  10. User control of the proton beam injection trajectories into the AGS Booster

    International Nuclear Information System (INIS)

    D'Ottavio, T.; Kponou, A.; Luccio, A.; Alessi, J.G.; Reece, R.K.; Skelly, J.

    1991-01-01

    The 1.5 GeV (proton) Booster Synchrotron nearing completion at the AGS will get its 200 MeV beam from the linac, via a 34.9 m long linac-to-Booster transport line, LTB. LTB branches off from the existing linac-to-AGS transport line, HEBT, approximately 18.4 m downstream from the linac. A schematic layout of LTB is shown in the bottom part of Fig. 1. The four dipoles, DH2 through DH5, which are identical and are operated in series, provide a 126 degrees bend in the line. We have employed three strategies for implementing control of the trajectory, namely: (1) a global correction (2) a local correction (3) a zeroing correction. These, as well as their implementation, will be discussed. Operating experience obtained from early commissioning runs will be given. The hardware used to implement the correction schemes are the beam position monitors, BPMxxx, orbit correctors, DHxxx and DVxxx, and multiwire profile monitors, MWxxx. The quads are QHxxx and QVxxx. 3 refs., 3 figs

  11. The use of seat belts and contributing factors : an international comparison.

    NARCIS (Netherlands)

    Mäkinen, T. Wittink, R.D. & Hagenzieker, M.P.

    1991-01-01

    The purpose of this study was to define factors that contribute to the use or non-use of seat belts. Legislation prescribing compulsory seat belt usage is one of the most important factors. Promotion of the use of seat belts without this legislation is very difficult and time-consuming. So far, the

  12. MIT-Skywalker: Evaluating comfort of bicycle/saddle seat.

    Science.gov (United States)

    Goncalves, Rogerio S; Hamilton, Taya; Daher, Ali R; Hirai, Hiroaki; Krebs, Hermano I

    2017-07-01

    The MIT-Skywalker is a robotic device developed for the rehabilitation of gait and balance after a neurological injury. This device has been designed based on the concept of a passive walker and provides three distinct training modes: discrete movement, rhythmic movement, and balance training. In this paper, we present our efforts to evaluate the comfort of a bicycle/saddle seat design for the system's novel actuated body weight support device. We employed different bicycle and saddle seats and evaluated comfort using objective and subjective measures. Here we will summarize the results obtained from a study of fifteen healthy subjects and one stroke patient that led to the selection of a saddle seat design for the MIT-Skywalker.

  13. Autist mobile seat's frame strength simulation used in a car

    Science.gov (United States)

    Suryo, S. H.; Jamari, J.; Naufal, G. K.; Ismail, R.; Bayuseno, A. P.; Desiningrum, D. R.

    2016-04-01

    Going on a car with autistic children needs a special handling. Autistic children that tend to be hyperactive in the car may disturb driving. A tool is needed to keep them in a calm state when they are in the car. Autist Mobile Seat is an aid for the autistic children when going on a car. The aid is an additional seat paired with the main seat of the car. This aid consists of three main things: Main frame, body skin, and pneumatic system. Frame as the main component supporting the Autist Mobile Seat functions as a holder as well as a body skin retainer in order to be able to retain the body of the autistic children. The strength of the frame from this Autist Mobile Seat should be counted as an anticipation from the failure of the frame function when receiving load when used by the autistic children in the car. Consequently, a test on the frame of the Autist Mobile Seat towards the load received should be conducted by using a method of FEM (Finite Element Method) with the help of commercial software. The simulation produces the maximum strength, the frame towards the load received as well as the critical point on the frame when loading occurs.

  14. Emittance measurement and modeling for the Fermilab Booster

    Directory of Open Access Journals (Sweden)

    Xiaobiao Huang

    2006-01-01

    Full Text Available Turn-by-turn beam profile data measured at the Fermilab Booster are studied. Lattice models with experimental accelerator ramping parameters are used to obtain the lattice functions for data analysis. We studied the horizontal and vertical emittance growth behavior in different stages of a booster ramping cycle and its relation to the beam intensity. The transverse and longitudinal components in the horizontal beam width are separated by a fitting model which makes use of the different scaling rules of the beam momentum. We analyze the post-transition horizontal beam size oscillation based on a model where the longitudinal phase-space mismatch has resulted from rf voltage mismatch during the transition-energy crossing. We carried out systematic multiparticle simulation to show that the source of the vertical emittance growth is a combination of the random errors in skew-quadrupole and dipole fields, and the systematic Montague resonance. The effect of random quadrupole field is small for the Fermilab Booster because the betatron envelope tunes are reasonably far away from the half-integer stop band.

  15. Percentage of Drivers and Front Seat Passengers Wearing Seat Belts, 2012 & 2014, All States

    Data.gov (United States)

    U.S. Department of Health & Human Services — Source for 2012 national data: National Occupant Protection Use Survey (NOPUS), 2012. Source for 2012 state data: State Observational Survey of Seat Belt Use, 2012....

  16. 14 CFR 125.211 - Seat and safety belts.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Seat and safety belts. 125.211 Section 125... Requirements § 125.211 Seat and safety belts. (a) No person may operate an airplane unless there are available... the airplane who is at least 2 years old; and (2) An approved safety belt for separate use by each...

  17. "Hot Seat" Questioning: A Technique to Promote and Evaluate Student Dialogue

    Science.gov (United States)

    Crider, Anthony

    Several approaches have been proposed to include students in classroom dialogue, including "think-pair-share" and "talk to your neighbor." I recently implemented an additional technique in which four students answer questions in a "Hot Seat" at the front of the classroom. An unforeseen by-product of this was student-initiated peer instruction outside of the classroom. A small case study (approximately 50 students) on the effect of the Hot Seat using the midterm exam showed that students were 9.5 +/- 3.2% more likely to correctly answer a question related to material covered while they occupied the Hot Seat. Analysis of the Astronomy Diagnostic Test revealed that they were twice as likely to learn their Hot Seat material. A survey revealed one likely reason: Students typically spent 15-60 additional minutes preparing for class on their two assigned Hot Seat dates. Curiously, students received no significant benefit (2.2 +/- 3.6%) from their second turn in the Hot Seat, possibly reflecting student immunization to its motivational pressure.

  18. An Ergonomic Desk and Chair Prototype to Improve Seating Position on Senior High School Students at Kabupaten Gresik

    Directory of Open Access Journals (Sweden)

    Neffrety Nilamsari

    2015-04-01

    chair N, length = 48 cm, wide = 43 cm, cushion base’s height from floor surfaces = 47 cm, bag keeper’s height from floor surfaces =3cm, bag keeper’s wide= 43 cm, bag keeper’s length = 47 cm, cushion’s wide = 41 cm, cushion’s length = 46cm, handrest’s height = 22 cm, handrest’s length = 30 cm, backrest’s height = 38 cm, backrest’s wide = 43 cm, cushion’s foam thickness = 4 cm, backrest’s foam thickness = 4 cm; 2 Prototype desk N, length = 50 cm, wide = 66 cm, back section’s height = 85 cm, front section’s height = 75 cm, footrest from fl oor surfaces = 10 cm, drawer’s height = 10cm, front bamper’s height = 40 cm, and table’s angle = 10o. Discussion: An ergonomic desks and chairs are very important for students at school, it will help teaching learning process run well and comfortable. The measurement of desk and chair must be reviewed after fi ve years, because of student’s anthropometric development. So then students will feel no fatigue. Keywords: ergonomy, senior high school student’s seating position

  19. 76 FR 11680 - Digital Low Power Television, Television Translator, and Television Booster Stations and Digital...

    Science.gov (United States)

    2011-03-03

    ...] Digital Low Power Television, Television Translator, and Television Booster Stations and Digital Class A... Commission's Rules to Establish Rules for Digital Low Power, Television Translator, and Television Booster... Digital Low Power Television Translator, Television Booster Stations, and to Amend Rules for Digital Class...

  20. NASA's Space Launch System: Developing the World's Most Powerful Solid Booster

    Science.gov (United States)

    Priskos, Alex

    2016-01-01

    NASA's Journey to Mars has begun. Indicative of that challenge, this will be a multi-decadal effort requiring the development of technology, operational capability, and experience. The first steps are under way with more than 15 years of continuous human operations aboard the International Space Station (ISS) and development of commercial cargo and crew transportation capabilities. NASA is making progress on the transportation required for deep space exploration - the Orion crew spacecraft and the Space Launch System (SLS) heavy-lift rocket that will launch Orion and large components such as in-space stages, habitat modules, landers, and other hardware necessary for deep-space operations. SLS is a key enabling capability and is designed to evolve with mission requirements. The initial configuration of SLS - Block 1 - will be capable of launching more than 70 metric tons (t) of payload into low Earth orbit, greater mass than any other launch vehicle in existence. By enhancing the propulsion elements and larger payload fairings, future SLS variants will launch 130 t into space, an unprecedented capability that simplifies hardware design and in-space operations, reduces travel times, and enhances the odds of mission success. SLS will be powered by four liquid fuel RS-25 engines and two solid propellant five-segment boosters, both based on space shuttle technologies. This paper will focus on development of the booster, which will provide more than 75 percent of total vehicle thrust at liftoff. Each booster is more than 17 stories tall, 3.6 meters (m) in diameter and weighs 725,000 kilograms (kg). While the SLS booster appears similar to the shuttle booster, it incorporates several changes. The additional propellant segment provides additional booster performance. Parachutes and other hardware associated with recovery operations have been deleted and the booster designated as expendable for affordability reasons. The new motor incorporates new avionics, new propellant

  1. Beam Based RF Voltage Measurements and Longitudinal Beam Tomography at the Fermilab Booster

    Energy Technology Data Exchange (ETDEWEB)

    Bhat, C. M. [Fermilab; Bhat, S. [Fermilab

    2017-10-19

    Increasing proton beam power on neutrino production targets is one of the major goals of the Fermilab long term accelerator programs. In this effort, the Fermilab 8 GeV Booster synchrotron plays a critical role for at least the next two decades. Therefore, understanding the Booster in great detail is important as we continue to improve its performance. For example, it is important to know accurately the available RF power in the Booster by carrying out beam-based measurements in order to specify the needed upgrades to the Booster RF system. Since the Booster magnetic field is changing continuously measuring/calibrating the RF voltage is not a trivial task. Here, we present a beam based method for the RF voltage measurements. Data analysis is carried out using computer programs developed in Python and MATLAB. The method presented here is applicable to any RCS which do not have flat-bottom and flat-top in the acceleration magnetic ramps. We have also carried out longitudinal beam tomography at injection and extraction energies with the data used for RF voltage measurements. Beam based RF voltage measurements and beam tomography were never done before for the Fermilab Booster. The results from these investigations will be very useful in future intensity upgrades.

  2. Resection of deep-seated brain glioma by microsurgery assisted with neuronavigation

    International Nuclear Information System (INIS)

    Feng Ming; Zhou Youxin; Sun Chunming; Zhang Shiming

    2009-01-01

    Objective: To investigate the clinical value of neuronavigator assisted microsurgery for deep-seated brain glioma. Methods: The electromagnetic neuronavigation system had been applied for microsurgery of deep-seated brain glioma in fifteen cases. Results: Ten from 15 patients were totally removed, 2 were subtotally removed and 3 were partial removed.All patients had no new neurological deficit. Conclusion: The neuronavigator assisted microsurgery for deep-seated brain glioma is of characters including accurate location, minimal invasiveness, and can enhance the rate of total resection and decrease the operative complications in the patients with deep-seated brain glioma. (authors)

  3. A new landing impact attenuation seat in manned spacecraft biologically-inspired by felids

    Directory of Open Access Journals (Sweden)

    Yu Hui

    2015-04-01

    Full Text Available When manned spacecraft comes back to the earth, it relies on the impact attenuation seat to protect astronauts from injuries during landing phase. Hence, the seat needs to transfer impact load, as small as possible, to the crew. However, there is little room left for traditional seat to improve further. Herein, a new seat system biologically-inspired by felids’ landing is proposed. Firstly, a series of experiments was carried out on cats and tigers, in which they were trained to jump down voluntarily from different heights. Based on the ground reaction forces combined with kinematics, the experiment indicated that felids’ landing after self-initial jump was a multi-step impact attenuation process and the new seat was inspired by this. Then the construction and work process of new seat were redesigned to realize the multi-step impact attenuation. The dynamic response of traditional and new seat is analyzed under the identical conditions and the results show that the new concept seat can significantly weaken the occupant overload in two directions compared with that of traditional seat. As a consequence, the risk of injury evaluated for spinal and head is also lowered, meaning a higher level of protection which is especially beneficial to the debilitated astronaut.

  4. Thermoeconomic model of a commercial transcritical booster refrigeration system

    DEFF Research Database (Denmark)

    Ommen, Torben Schmidt; Elmegaard, Brian

    2011-01-01

    For cooling applications in supermarkets, booster refrigeration systems operating in both transcritical and subcritical conditions are increasingly used. A thermodynamic model of a transcritical booster refrigeration plant is tailored to match the new generation of commercial refrigeration plants...... of exergy for cooling. Second law analysis is needed to illustrate the characteristics of the plant at different load rates, according to the alternating load profile and corresponding to outdoor conditions. With the detailed model, different uses of the analysis are possible, including thermoeconomic...

  5. Experimental verification of numerical calculations of railway passenger seats

    Science.gov (United States)

    Ligaj, B.; Wirwicki, M.; Karolewska, K.; Jasińska, A.

    2018-04-01

    The construction of railway seats is based on industry regulations and the requirements of end users, i.e. passengers. The two main documents in this context are the UIC 566 (3rd Edition, dated 7 January 1994) and the EN 12663-1: 2010+A1:2014. The study was to carry out static load tests of passenger seat frames. The paper presents the construction of the test bench and the results of experimental and numerical studies of passenger seat rail frames. The test bench consists of a frame, a transverse beam, two electric cylinders with a force value of 6 kN, and a strain gauge amplifier. It has a modular structure that allows for its expansion depending on the structure of the seats. Comparing experimental results with numerical results for points A and B allowed to determine the existing differences. It follows from it that higher stress values are obtained by numerical calculations in the range of 0.2 MPa to 35.9 MPa.

  6. Biomechanical investigation of prolonged driving in an ergonomically designed truck seat prototype.

    Science.gov (United States)

    Cardoso, Michelle; McKinnon, Colin; Viggiani, Dan; Johnson, Michel J; Callaghan, Jack P; Albert, Wayne J

    2018-03-01

    A postural evaluation during a prolonged driving task was conducted to determine the ergonomic validity of a new freely adjustable truck seat prototype. Twenty participants were recruited to perform two 2-h simulated driving sessions. Postures were assessed using motion capture, accelerometers and pressure pads. Subjective discomfort was also monitored in 15-min increments using ratings of perceived discomfort (RPD) and the Automotive Seating Discomfort Questionnaire. Participants had a more neutral spine posture during the first hour of the drive and reported lower RPDs while sitting in the prototype. Pairing the gluteal backrest panel with the adjustable seat pan helped reduce the average sitting pressure. The industry-standard truck seat may lead to the development of poor whole body posture, and the proposed ergonomic redesign of a new truck seat helped improve sitting posture and reduce perceived discomfort. Practitioner Summary: A new freely adjustable truck seat prototype was compared to an Industry standard seat to assess hypothesised improvements to sitting posture and discomfort for long haul driving. It was found that the adjustable panels in the prototype helped promote spine posture, reduce sitting pressure and improved discomfort ratings.

  7. 75 FR 58340 - Airworthiness Directives; Koito Industries, Ltd., Seats and Seating Systems Approved Under...

    Science.gov (United States)

    2010-09-24

    ... under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States... cable, hook and loop (hook and loop is a generic term for Velcro), leather cover that is glued to seat...

  8. Numerically controlled oscillator for the Fermilab Booster

    International Nuclear Information System (INIS)

    Crisp, J.L.; Ducar, R.J.

    1989-01-01

    In order to improve the stability of the Fermilab Booster low level rf system, a numerically controlled oscillator system is being constructed. Although the system has not been implemented to date, the design is outlined in this paper. The heart of the new system consists of a numerically synthesized frequency generator manufactured by the Sciteq Company. The 3 GHz/sec rate and 30 to 53 MHz range of the Booster frequency program required the design of a CAMAC based, fast-cycling (1 MHz), 65K x 32 bit, digital function generator. A 1 MHz digital adder and 12 bit analog to digital converter will be used to correct small program errors by phase locking the oscillator to the beam. 6 refs., 1 fig

  9. Seat Adjustment Design of an Intelligent Robotic Wheelchair Based on the Stewart Platform

    Directory of Open Access Journals (Sweden)

    Po Er Hsu

    2013-03-01

    Full Text Available A wheelchair user makes direct contact with the wheelchair seat, which serves as the interface between the user and the wheelchair, for much of any given day. Seat adjustment design is of crucial importance in providing proper seating posture and comfort. This paper presents a multiple-DOF (degrees of freedom seat adjustment mechanism, which is intended to increase the independence of the wheelchair user while maintaining a concise structure, light weight, and intuitive control interface. This four-axis Stewart platform is capable of heaving, pitching, and swaying to provide seat elevation, tilt-in-space, and sideways movement functions. The geometry and types of joints of this mechanism are carefully arranged so that only one actuator needs to be controlled, enabling the wheelchair user to adjust the seat by simply pressing a button. The seat is also equipped with soft pressure-sensing pads to provide pressure management by adjusting the seat mechanism once continuous and concentrated pressure is detected. Finally, by comparing with the manual wheelchair, the proposed mechanism demonstrated the easier and more convenient operation with less effort for transfer assistance.

  10. The operational status of the Booster injector for the AGS accelerator complex at BNL

    International Nuclear Information System (INIS)

    Ahrens, L.; Bleser, E.; Brennan, J.M.; Gardner, C.; Gill, E.; Glenn, J.W.; Reece, K.; Roser, T.; van Asselt, W.; Weng, W.T.

    1992-01-01

    The Booster synchrotron at Brookhaven National Laboratory has been incorporated into the accelerator chain at the Alternating Gradient Synchrotron (AGS) complex. After a successful first commissioning effort in the spring of 1991, the Booster has been part of this year's silicon, gold and proton physics runs. After a brief review of the Booster design goals, and of the early commissioning, this paper will summarize this year's activities

  11. Self-reported seat discomfort among Dutch commercial truck drivers

    NARCIS (Netherlands)

    Tan, C.F.; Chen, W.; Rauterberg, G.W.M.

    2010-01-01

    Comfort is an attribute that today’s consumers demand more and more. The seat has an important role to play in fulfilling these comfort expectations. Seating comfort is a major concern for drivers and other members of the work force who are exposed to extended periods of sitting and its associated

  12. GRYPHON: Air launched space booster

    Science.gov (United States)

    1993-06-01

    The project chosen for the winter semester Aero 483 class was the design of a next generation Air Launched Space Booster. Based on Orbital Sciences Corporation's Pegasus concept, the goal of Aero 483 was to design a 500,000 pound air launched space booster capable of delivering 17,000 pounds of payload to Low Earth Orbit and 8,000 pounds of payload to Geosynchronous Earth Orbit. The resulting launch vehicle was named the Gryphon. The class of forty senior aerospace engineering students was broken down into eight interdependent groups. Each group was assigned a subsystem or responsibility which then became their field of specialization. Spacecraft Integration was responsible for ensuring compatibility between subsystems. This group kept up to date on subsystem redesigns and informed those parties affected by the changes, monitored the vehicle's overall weight and dimensions, and calculated the mass properties of the booster. This group also performed the cost/profitability analysis of the Gryphon and obtained cost data for competing launch systems. The Mission Analysis Group was assigned the task of determining proper orbits, calculating the vehicle's flight trajectory for those orbits, and determining the aerodynamic characteristics of the vehicle. The Propulsion Group chose the engines that were best suited to the mission. This group also set the staging configurations for those engines and designed the tanks and fuel feed system. The commercial satellite market, dimensions and weights of typical satellites, and method of deploying satellites was determined by the Payloads Group. In addition, Payloads identified possible resupply packages for Space Station Freedom and identified those packages that were compatible with the Gryphon. The guidance, navigation, and control subsystems were designed by the Mission Control Group. This group identified required tracking hardware, communications hardware telemetry systems, and ground sites for the location of the Gryphon

  13. Fiber optics in the BNL Booster radiation environment

    International Nuclear Information System (INIS)

    Beadle, E.R.

    1991-01-01

    The Booster instrumentation uses analog and digital fiber optic links, designed to withstand at least 50 krads without performance degradation. The links use inexpensive and commercially available components that operate at a center wavelength of 820 nm. The analog link operates to 30 MHz over a 200 m fiber and can provide insertion gain. The digital link provides 60 ns timing pulses without the dispersive effects of coaxial cables. The optical fiber is a step-index hard clad silica type with a 200 micron core. This paper presents the component selection criteria, link design, installation, testing and performance for the optical links in the Booster instrumentation systems

  14. Development of adaptive helicopter seat systems for aircrew vibration mitigation

    Science.gov (United States)

    Chen, Yong; Wickramasinghe, Viresh; Zimcik, David G.

    2008-03-01

    Helicopter aircrews are exposed to high levels of whole body vibration during flight. This paper presents the results of an investigation of adaptive seat mount approaches to reduce helicopter aircrew whole body vibration levels. A flight test was conducted on a four-blade helicopter and showed that the currently used passive seat systems were not able to provide satisfactory protection to the helicopter aircrew in both front-back and vertical directions. Long-term exposure to the measured whole body vibration environment may cause occupational health issues such as spine and neck strain injuries for aircrew. In order to address this issue, a novel adaptive seat mount concept was developed to mitigate the vibration levels transmitted to the aircrew body. For proof-of-concept demonstration, a miniature modal shaker was properly aligned between the cabin floor and the seat frame to provide adaptive actuation authority. Adaptive control laws were developed to reduce the vibration transmitted to the aircrew body, especially the helmet location in order to minimize neck and spine injuries. Closed-loop control test have been conducted on a full-scale helicopter seat with a mannequin configuration and a large mechanical shaker was used to provide representative helicopter vibration profiles to the seat frame. Significant vibration reductions to the vertical and front-back vibration modes have been achieved simultaneously, which verified the technical readiness of the adaptive mount approach for full-scale flight test on the vehicle.

  15. The repeatability and reproducibility of the BioRID IIg in a repeatable laboratory seat based on a production car seat.

    Science.gov (United States)

    Hynd, David; Depinet, Paul; Lorenz, Bernd

    2013-01-01

    The United Nations Economic Commission for Europe Informal Group on GTR No. 7 Phase 2 are working to define a build level for the BioRID II rear impact (whiplash) crash test dummy that ensures repeatable and reproducible performance in a test procedure that has been proposed for future legislation. This includes the specification of dummy hardware, as well as the development of comprehensive certification procedures for the dummy. This study evaluated whether the dummy build level and certification procedures deliver the desired level of repeatability and reproducibility. A custom-designed laboratory seat was made using the seat base, back, and head restraint from a production car seat to ensure a representative interface with the dummy. The seat back was reinforced for use in multiple tests and the recliner mechanism was replaced by an external spring-damper mechanism. A total of 65 tests were performed with 6 BioRID IIg dummies using the draft GTR No.7 sled pulse and seating procedure. All dummies were subject to the build, maintenance, and certification procedures defined by the Informal Group. The test condition was highly repeatable, with a very repeatable pulse, a well-controlled seat back response, and minimal observed degradation of seat foams. The results showed qualitatively reasonable repeatability and reproducibility for the upper torso and head accelerations, as well as for T1 Fx and upper neck Fx . However, reproducibility was not acceptable for T1 and upper neck Fz or for T1 and upper neck My . The Informal Group has not selected injury or seat assessment criteria for use with BioRID II, so it is not known whether these channels would be used in the regulation. However, the ramping-up behavior of the dummy showed poor reproducibility, which would be expected to affect the reproducibility of dummy measurements in general. Pelvis and spine characteristics were found to significantly influence the dummy measurements for which poor reproducibility was

  16. Accessing hospital packaged foods and beverages: the importance of a seated posture when eating.

    Science.gov (United States)

    Bell, A; Tapsell, L; Walton, K; Yoxall, A

    2017-06-01

    Hospitalised and community dwelling older people (aged 65 years and over) have difficulties opening certain food and beverage items (e.g. cheese portions and tetra packs) served in public hospitals. Previously, the role of hand strength on successful pack opening has been explored in a seated position. However, because many people in hospital eat in bed, the present laboratory study examined the differences between participants opening a selection of products in a hospital bed and a chair. The present study used a qualitative method (satisfaction) and quantitative methods (grip and pinch strength, dexterity, time and attempts) in two conditions (bed; chair) in a sample of well older community dwelling adults (n = 34). Packs tested included foil sealed thickened pudding, foil sealed thickened water, tetra pack, dessert, custard, jam, cereal, honey sachet and cheese portions. Honey sachets, cheese portions, foil sealed thickened pudding and tetra packs were the most difficult packs to open, with 15% of cheese portions unable to be opened in either the bed or chair posture. Although grip strength was consistent for each posture, pinch grips and dexterity were adversely affected by the bed posture. Lying in a hospital bed required greater pinch strength and dexterity to open packs. Eating in a seated position when in hospital has been shown to improve intake. The present study demonstrates that eating in a seated posture is also advantageous for opening the food and beverage packs used in the NSW hospital food service and supports the notion that patients should sit to eat in hospital. © 2016 The British Dietetic Association Ltd.

  17. The effect of a 3-point harness restraint and car seat in whiplash-type lateral impacts.

    Science.gov (United States)

    Kumar, Shrawan; Ferrari, Robert; Narayan, Yogesh; Jones, Troy

    2006-01-01

    Seventeen healthy volunteers were subjected to right and left lateral impacts 5.0, 6.8, 9.2, and 16.8 m/s acceleration while positioned in a Volvo car seat with lap and shoulder seat belt restraint in laboratory setting. The purpose of this study was to determine the effect of using a standard 3-point lap and shoulder seat belt and Volvo car seat on the response of the cervical muscles to increasing low-velocity lateral impacts. A previous study of lateral impacts in a 5-point harness restraint with head and trunk in neutral posture suggests that the burden of impact is borne primarily by the splenius capitis muscle contralateral to the direction of impact. That study, however, used a nonstandard harness for automobiles, and other studies suggest that a lap-and-shoulder seat belt may increase the risk of whiplash injury. Triaxial accelerometers recorded the acceleration of the 1) sled, 2) torso at the shoulder level, and 3) head of the participant, while bilateral electromyograms of the sternocleidomastoids, trapezii, and splenii capitis were also recorded. For participants experiencing a right or left lateral impact, the muscle responses increased with increasing levels of acceleration (P trend to progressively decrease with increasing levels of acceleration. The peak head accelerations relative to the sled ranged from 2.5 to 10.6 m/s. When the impact was a right lateral impact, at the highest sled acceleration, the left splenius capitis generated 47% of its maximal voluntary contraction (MVC), and the left trapezius also 46% of its MVC; the left and right sternocleidomastoid, right splenius capitis, and right trapezius generated 29% or less of their MVC. For the highest level of acceleration in a left lateral impact, the right splenius capitis generated 48% of its MVC and the right trapezius 57% of the MVC, the left and right sternocleidomastoid, left splenius capitis, and left trapezius generated 29% or less of their MVC. In both directions of impact, the

  18. Misuse of booster cushions among children and adults in Shanghai-an observational and attitude study during buckling up.

    Science.gov (United States)

    Bohman, Katarina; Jorlöv, Sofia; Zhou, Shengqi; Zhao, Cloud; Sui, Bo; Ding, Chengkai

    2016-10-02

    Traffic crashes are one of the leading causes of fatalities among Chinese children. Booster cushion usage in China is low, and there are no studies showing how a population with limited experience handles booster cushions during buckling up. The purpose of this study was to evaluate the handling of and explore the attitudes toward booster cushions among children, parents, and grandparents in Shanghai. An observational study including a convenience sample of 254 children aged 4-12 years was conducted in 2 passenger cars at a shopping center in Shanghai. Parents, grandparents, or the children themselves buckled up the child on 2 types of booster cushions, a 2-stage integrated booster cushion (IBC) and an aftermarket booster cushion (BC). The test participants were observed during buckling up, first without and then with instructions. The test leaders conducted structured interviews. Ninety-eight percent of the uninstructed participants failed to buckle up without identified misuse on the aftermarket booster cushion and 31% of those uninstructed on the integrated booster cushion. The majority of misuse was severe, including placing the belt behind the arm and the lap belt routing above the guiding loops. Instruction reduced misuse to 58% (BC) and 12% (IBC), respectively, and, in particular, severe misuse. Some misuse was related to limited knowledge of how to buckle up on the booster cushion, and some misuse was intentional in order to reduce discomfort. The participants, both children and adults, reported that they preferred the IBC due to good comfort and convenience. Safety was reported as the main reason for adults using booster cushions in general, whereas children reported comfort as the most important motivation. Education is needed to ensure frequent and correct use of booster cushions in China and to raise safety awareness among children and adults. Furthermore, it is important that the booster cushions offer intuitively correct usage to a population with

  19. YALINA Booster subcritical assembly modeling and analyses

    International Nuclear Information System (INIS)

    Talamo, A.; Gohar, Y.; Aliberti, G.; Cao, Y.; Zhong, Z.; Kiyavitskaya, H.; Bournos, V.; Fokov, Y.; Routkovskaya, C.; Sadovich, S.

    2010-01-01

    Full text: Accurate simulation models of the YALINA Booster assembly of the Joint Institute for Power and Nuclear Research (JIPNR)-Sosny, Belarus have been developed by Argonne National Laboratory (ANL) of the USA. YALINA-Booster has coupled zones operating with fast and thermal neutron spectra, which requires a special attention in the modelling process. Three different uranium enrichments of 90%, 36% or 21% were used in the fast zone and 10% uranium enrichment was used in the thermal zone. Two of the most advanced Monte Carlo computer programs have been utilized for the ANL analyses: MCNP of the Los Alamos National Laboratory and MONK of the British Nuclear Fuel Limited and SERCO Assurance. The developed geometrical models for both computer programs modelled all the details of the YALINA Booster facility as described in the technical specifications defined in the International Atomic Energy Agency (IAEA) report without any geometrical approximation or material homogenization. Materials impurities and the measured material densities have been used in the models. The obtained results for the neutron multiplication factors calculated in criticality mode (keff) and in source mode (ksrc) with an external neutron source from the two Monte Carlo programs are very similar. Different external neutron sources have been investigated including californium, deuterium-deuterium (D-D), and deuterium-tritium (D-T) neutron sources. The spatial neutron flux profiles and the neutron spectra in the experimental channels were calculated. In addition, the kinetic parameters were defined including the effective delayed neutron fraction, the prompt neutron lifetime, and the neutron generation time. A new calculation methodology has been developed at ANL to simulate the pulsed neutron source experiments. In this methodology, the MCNP code is used to simulate the detector response from a single pulse of the external neutron source and a C code is used to superimpose the pulse until the

  20. The transmission of vertical vibration through seats: Influence of the characteristics of the human body

    Science.gov (United States)

    Toward, Martin G. R.; Griffin, Michael J.

    2011-12-01

    The transmission of vibration through a seat depends on the impedance of the seat and the apparent mass of the seat occupant. This study was designed to determine how factors affecting the apparent mass of the body (age, gender, physical characteristics, backrest contact, and magnitude of vibration) affect seat transmissibility. The transmission of vertical vibration through a car seat was measured with 80 adults (41 males and 39 females aged 18-65) at frequencies between 0.6 and 20 Hz with two backrest conditions (no backrest and backrest), and with three magnitudes of random vibration (0.5, 1.0, and 1.5 m s -2 rms). Linear regression models were used to study the effects of subject physical characteristics (age, gender, and anthropometry) and features of their apparent mass (resonance frequency, apparent mass at resonance and at 12 Hz) on the measured seat transmissibility. The strongest predictor of both the frequency of the principal resonance in seat transmissibility and the seat transmissibility at resonance was subject age, with other factors having only marginal effects. The transmissibility of the seat at 12 Hz depended on subject age, body mass index, and gender. Although subject weight was strongly associated with apparent mass, weight was not strongly associated with seat transmissibility. The resonance frequency of the seat decreased with increases in the magnitude of the vibration excitation and increased when subjects made contact with the backrest. Inter-subject variability in the resonance frequency and transmissibility at resonance was less with greater vibration excitation, but was largely unaffected by backrest contact. A lumped parameter seat-person model showed that changes in seat transmissibility with age can be predicted from changes in apparent mass with age, and that the dynamic stiffness of the seat appeared to increase with increased loading so as to compensate for increases in subject apparent mass associated with increased sitting

  1. Seat-belt use still low in Kuwait: self-reported driving behaviours among adult drivers.

    Science.gov (United States)

    Raman, Sudha R; Ottensmeyer, C Andrea; Landry, Michel D; Alfadhli, Jarrah; Procter, Steven; Jacob, Susan; Hamdan, Elham; Bouhaimed, Manal

    2014-01-01

    Kuwait mandated seat-belt use by drivers in 1976 and by front seat passengers in 1994. The study objectives were to identify and estimate current factors associated with seat-belt use and levels of potentially unsafe driving behaviours in Kuwait. In 2010, 741 adults were surveyed regarding driving habits and history. Only 41.6% of drivers reported always using a seat belt. Front seat passenger belt use was more common (30.5%) than rear seat belt use (6.5%). Distracted driving behaviours were common, including mobile phone use ('always' or 'almost always': 51.1%) and texting/SMS (32.4%). Logistic regression indicated that drivers who were young (18-19 years), male, Kuwaiti nationals or non-Kuwaiti Arabs, drove over the speed limit, had traffic violation tickets or >1 car crashes in the last year, were less likely to use seat belts. Targeted initiatives to increase public awareness and to enforce car-safety legislation, including use of seat belts, are necessary to decrease the health burden of car crashes in Kuwait.

  2. 76 FR 31803 - Airworthiness Directives; Koito Industries, Ltd., Seats and Seating Systems Approved Under...

    Science.gov (United States)

    2011-06-02

    ... CONTACT: Patrick Farina, Aerospace Engineer, Cabin Safety Branch, ANM-150L, FAA, Los Angeles Aircraft... understands that the FAA considers this phased testing structure as an acceptable testing plan, but also... the suspect seats were witnessed by FAA ``delegates'' (designated engineering representatives (DERs...

  3. Race, belief in destiny, and seat belt usage: a pilot study.

    Science.gov (United States)

    Colón, I

    1992-01-01

    A survey of 1063 individuals found that when belief in destiny was statistically controlled, differences in seat belt use by race disappeared. Thus, racial differences in seat belt use are statistically accounted for and might be explained by belief in destiny. Efforts to increase seat belt use should target minority groups rather than include them in broadbrush programs. Further, these efforts should take into account this important difference in motivation. PMID:1585969

  4. Effects of Wheelchair Seat-height Settings on Alternating Lower Limb Propulsion With Both Legs.

    Science.gov (United States)

    Murata, Tomoyuki; Asami, Toyoko; Matsuo, Kiyomi; Kubo, Atsuko; Okigawa, Etsumi

    2014-01-01

    This study investigated the effects of seat-height settings of wheelchairs with alternating propulsion with both legs. Seven healthy individuals with no orthopedic disease participated. Flexion angles at initial contact (FA-IC) of each joint, range of motion during propulsion period (ROM-PP), and ground reaction force (GRF) were measured using a three dimensional motion capture system and force plates, and compared with different seat-height settings. Statistically significant relationships were found between seat-height and speed, stride length, knee FA-IC, ankle FA-IC, hip ROM-PP, vertical ground reaction force (VGRF), and anterior posterior ground reaction force (APGRF). Speed, hip ROM-PP, VGRF and APGRF increased as the seat-height was lowered. This effect diminished when the seat-height was set below -40 mm. VGRF increased as the seat-height was lowered. The results suggest that the seat-height effect can be attributed to hip ROM-PP; therefore, optimal foot propulsion cannot be achieved when the seat height is set either too high or too low. Efficient foot propulsion of the wheelchair can be achieved by setting the seat height to lower leg length according to a combination of physical characteristics, such as the user's physical functions, leg muscles, and range of motion.

  5. Nonconformities in real-world fatal crashes--electronic stability control and seat belt reminders.

    Science.gov (United States)

    Lie, Anders

    2012-01-01

    Many new safety systems are entering the market. Vision Zero is a safety strategy aiming at the elimination of fatalities and impairing injuries by the use of a holistic model for safe traffic to develop a safe system. The aim of this article is to analyze fatalities in modern cars with respect to the Vision Zero model with special respect to electronic stability control (ESC) systems and modern seat belt reminders (SBRs). The model is used to identify and understand cases where cars with ESC systems lost control and where occupants were unbelted in a seat with seat belt reminders under normal driving conditions. The model for safe traffic was used to analyze in-depth studies of fatal crashes with respect to seat belt use and loss of control. Vehicles from 2003 and later in crashes from January 2004 to mid-2010 were analyzed. The data were analyzed case by case. Cars that were equipped with ESC systems and lost control and occupants not using the seat belt in a seat with a seat belt reminder were considered as nonconformities. A total of 138 fatal crashes involving 152 fatally injured occupants were analyzed. Cars with ESC systems had fewer loss-of-control-relevant cases than cars without ESC systems. Thirteen percent of the ESC-equipped vehicles had loss-of-control-relevant crashes and 36 percent of the cars without ESC systems had loss-of-control-relevant crashes. The analysis indicates that only one car of the 9 equipped with ESC that lost control did it on a road surface with relevant friction when driving within the speed restriction of the road. In seats with seat belt reminders that are in accordance with the European New Car Assessment Programme's (Euro NCAP) protocol, 93 percent of the occupants were using a seat belt. In seats without reminders this number was 74 percent. This study shows that ESC systems result in a very significant reduction in fatal crashes, especially under normal driving conditions. Under extreme driving conditions such as speeding

  6. New Pulsed Orbit Bump Magnets for the Fermilab Booster Synchrotron

    CERN Document Server

    Lackey, James; John, Carson; Kashikhin, Vladimir; Makarov, Alexander; Prebys, Eric

    2005-01-01

    The beam from the Fermilab Linac is injected onto a bump in the closed orbit of the Booster Synchrotron where a carbon foil strips the electrons from the Linac’s negative ion hydrogen beam. Although the Booster itself runs at 15Hz, heat dissipation in the orbit bump magnets has been one limitation to the fraction of the cycles that can be used for beam. New, 0.28T pulsed window frame dipole magnets have been constructed that will fit into the same space as the old ones, run at the full repetition rate of the Booster, and provide a larger bump to allow a cleaner injection orbit. The new magnets use a high saturation flux density Ni-Zn ferrite in the yoke rather than laminated steel. The presented magnetic design includes two and three dimensional magnetic field calculations with eddy currents and ferrite nonlinear effects.

  7. Some understandings on radial motion at transition in the Fermilab Booster

    International Nuclear Information System (INIS)

    Yang, Xi

    2007-01-01

    The transition crossing is space charge dominated in the Fermilab Booster. Since the longitudinal space charge forces are defocusing below transition and focusing above transition, they generate the mismatch at transition, which causes the longitudinal emittance growth above transition. It's proved by numerical simulation that such mismatch can be partially compensated by a particular radial motion at transition, which is operationally favored by the high intensity beam. The transition crossing in Booster is space charge dominated. Usually, the nonlinear chromatic effect can cause the emittance growth during transition because particles with different energies cross transition at different times. The transition time is set by the synchronous particle; below transition, particles with positive energies relative to the synchronous particle become unstable since they are in the wrong phase, and above transition, particles with negative energies are unstable. The dependence of the transition energy upon the momentum deviation can be adjusted via different sextupole corrector settings such that the emittance growth due to the chromatic nonlinear effect can be greatly reduced. Fortunately, at the corrector setting of I sextl = -97 A and I sexts = 97 A, the dependence can be removed, see Figure 1. Space charge forces are mainly responsible for the longitudinal emittance growth at transition

  8. Rf beam control for the AGS Booster

    International Nuclear Information System (INIS)

    Brennan, J.M.

    1994-01-01

    RF beam control systems for hadron synchrotrons have evolved over the past three decades into an essentially standard design. The key difference between hadron and lepton machines is the absence of radiation damping and existence of significant frequency variation in the case of hadrons. Although the motion of the hadron in the potential well of the rf wave is inherently stable it is not strongly damped. Damping must be provided by electronic feedback through the accelerating system. This feedback is typically called the phase loop. The technology of the rf beam control system for the AGS Booster synchrotron is described. First, the overall philosophy of the design is explained in terms of a conventional servo system that regulates the beam horizontal position in the vacuum chamber. The concept of beam transfer functions is fundamental to the mathematics of the design process and is reviewed. The beam transfer functions required for this design are derived from first principles. An overview of the beam signal pick-ups and high level rf equipment is given. The major subsystems, the frequency program, the heterodyne system, and beam feedback loops, are described in detail. Beyond accelerating the beam, the rf system must also synchronize the bunches in the Booster to the buckets in the AGS before transfer. The technical challenge in this process is heightened by the need to accomplish synchronization while the frequency is still changing. Details of the synchronization system are given. This report is intended to serve two purposes. One is to document the hardware and performance of the systems that have been built. The other is to serve as a tutorial vehicle from which the non-expert can not only learn the details of this system but also learn the principles of beam control that have led to the particular design choices made

  9. Rf beam control for the AGS Booster

    Energy Technology Data Exchange (ETDEWEB)

    Brennan, J.M.

    1994-09-26

    RF beam control systems for hadron synchrotrons have evolved over the past three decades into an essentially standard design. The key difference between hadron and lepton machines is the absence of radiation damping and existence of significant frequency variation in the case of hadrons. Although the motion of the hadron in the potential well of the rf wave is inherently stable it is not strongly damped. Damping must be provided by electronic feedback through the accelerating system. This feedback is typically called the phase loop. The technology of the rf beam control system for the AGS Booster synchrotron is described. First, the overall philosophy of the design is explained in terms of a conventional servo system that regulates the beam horizontal position in the vacuum chamber. The concept of beam transfer functions is fundamental to the mathematics of the design process and is reviewed. The beam transfer functions required for this design are derived from first principles. An overview of the beam signal pick-ups and high level rf equipment is given. The major subsystems, the frequency program, the heterodyne system, and beam feedback loops, are described in detail. Beyond accelerating the beam, the rf system must also synchronize the bunches in the Booster to the buckets in the AGS before transfer. The technical challenge in this process is heightened by the need to accomplish synchronization while the frequency is still changing. Details of the synchronization system are given. This report is intended to serve two purposes. One is to document the hardware and performance of the systems that have been built. The other is to serve as a tutorial vehicle from which the non-expert can not only learn the details of this system but also learn the principles of beam control that have led to the particular design choices made.

  10. SIT (seated immobility thromboembolism) syndrome: a 21st century lifestyle hazard.

    Science.gov (United States)

    Beasley, Richard; Heuser, Patricia; Raymond, Nigel

    2005-04-01

    The association between prolonged seated immobility and venous thromboembolism (VTE) is well recognised in relation to travel. In this case series, we report the occurrence of deep vein thrombosis (DVT) or pulmonary embolism (PE) following prolonged sitting in relation to work and/or recreation. The cases were characterised by the considerable length of time the individuals sat, the extensive nature of the VTE events in young individuals without other recognised risk factors, and the lack of recognition by the attending doctors of seated immobility as the likely major risk factor. While recognising that the association may be coincidental rather than causal, we propose the acronym 'SIT' (seated immobility thromboembolism) syndrome to encompass all forms of seated immobility associated with VTE.

  11. 47 CFR 73.827 - Interference to the input signals of FM translator or FM booster stations.

    Science.gov (United States)

    2010-10-01

    ... translator or FM booster stations. 73.827 Section 73.827 Telecommunication FEDERAL COMMUNICATIONS COMMISSION... Interference to the input signals of FM translator or FM booster stations. (a) An authorized LPFM station will not be permitted to continue to operate if an FM translator or FM booster station demonstrates that...

  12. Data acquisition and control of the Zero Gradient Synchrotron 500 MeV booster synchrotron

    International Nuclear Information System (INIS)

    Timm, R.E.; Forrestal, J.; Hogrefe, R.; Voss, D.

    1977-01-01

    A data acquisition and control philosophy for the Zero Gradient Synchrotron (ZGS) 500 MeV booster has involved a top down design incorporating all of the systems comprising the booster. Consideration of operational complexity was necessary because the booster is to be used simultaneously for ZGS injection, and solid state physics studies. Existing software and hardware capabilities of the ZGS computer were considered. The resulting data acquisition and control system is based on a mix of sequential logic and a minicomputer. Hardware considerations were based on a ten year life expectancy of the booster. Due to time, budget, and manpower constraints, the incorporation of the total design has been divided into three phases of implementation. The first phase is covered and the remaining phases are outlined

  13. Space shuttle booster multi-engine base flow analysis

    Science.gov (United States)

    Tang, H. H.; Gardiner, C. R.; Anderson, W. A.; Navickas, J.

    1972-01-01

    A comprehensive review of currently available techniques pertinent to several prominent aspects of the base thermal problem of the space shuttle booster is given along with a brief review of experimental results. A tractable engineering analysis, capable of predicting the power-on base pressure, base heating, and other base thermal environmental conditions, such as base gas temperature, is presented and used for an analysis of various space shuttle booster configurations. The analysis consists of a rational combination of theoretical treatments of the prominent flow interaction phenomena in the base region. These theories consider jet mixing, plume flow, axisymmetric flow effects, base injection, recirculating flow dynamics, and various modes of heat transfer. Such effects as initial boundary layer expansion at the nozzle lip, reattachment, recompression, choked vent flow, and nonisoenergetic mixing processes are included in the analysis. A unified method was developed and programmed to numerically obtain compatible solutions for the various flow field components in both flight and ground test conditions. Preliminary prediction for a 12-engine space shuttle booster base thermal environment was obtained for a typical trajectory history. Theoretical predictions were also obtained for some clustered-engine experimental conditions. Results indicate good agreement between the data and theoretical predicitons.

  14. Effect of reactor finiteness on the boundary condition at the surface of a booster section

    International Nuclear Information System (INIS)

    Wassef, W.A.

    1982-01-01

    Effect of reactor finiteness on the boundary condition at the surface of an absorbing booster embedded in the reactor core is studied and formulated. The model used in these calculations depends on the Pl-Transport coupling technique. This method takes into consideration the rigorous neutron transport behavior inside the booster medium, while the Pl-approximation in the bulk of the scattering medium surrounding the booster which can be considered infinite in most practical applications. The neutron flux gradient parallel to the surface of the booster is considered. The geometrical configuration of the reactor core cross section is circular or rectangular. Finiteness of the reactor is introduced in the general formulation through its dimensions or buckling. Extensive numerical results are given to demonstrate the dependence of the boundary condition at the surface of the booster section on the reactor finiteness and the different physical parameters

  15. Multi-Physics Analysis of the Fermilab Booster RF Cavity

    International Nuclear Information System (INIS)

    Awida, M.; Reid, J.; Yakovlev, V.; Lebedev, V.; Khabiboulline, T.; Champion, M.

    2012-01-01

    After about 40 years of operation the RF accelerating cavities in Fermilab Booster need an upgrade to improve their reliability and to increase the repetition rate in order to support a future experimental program. An increase in the repetition rate from 7 to 15 Hz entails increasing the power dissipation in the RF cavities, their ferrite loaded tuners, and HOM dampers. The increased duty factor requires careful modelling for the RF heating effects in the cavity. A multi-physic analysis investigating both the RF and thermal properties of Booster cavity under various operating conditions is presented in this paper.

  16. Booster Long 13 irradiation studies

    Energy Technology Data Exchange (ETDEWEB)

    Leveling, A.; Mokhov, N.; Moore, C.D.; /Fermilab

    1998-06-01

    Extraction from the Booster to the Main Ring occurred at Long Straight 13. The nature of the extraction process was such that 1% to 2% of the beam was lost in this region. There was an appreciable amount of beam extracted as shown in Table 1, which gives the yearly integrated intensities from 1973 to 1997. A simple model of the extraction losses was set up by Chandra Bhat utilizing the program CASIM. A sample output I shown in figure 1 which gives contours of stars/cm3 in the dirt, also schematically depicted are the three six feet deep sampling holes which were drilled to map out this cascade. One aspect of this study has been the study of the production of non-migrating nuclides and further study may in fact yield better values for the K parameter, the probability per star that an atom of the particular nuclide will be produced. Also the results of this study can give experimental numbers for the production of other nuclides when the amount of Na22 has been calculated. However, the most important part of this study has been the determination of the amount of tritium produced by extraction from the Booster and the experimentally determined migration rate. If we look at the top sample result in hole S2 of 777 pCi/ml of tritium and use the experimentally determined rate of migration and the depth to the aquifer of 13.1m, they calculate that the concentration will have decayed away to 1.1E-8 pCi/ml. If we look at the bottom sample, which is 11.3 m away from the aquifer, they calculate that the 116 pCi/ml will have decayed to 5.2E-8 pCi/ml. The conclusions is that the rate of migration determined over the 24 year irradiation history of the Booster extraction point is small enough that there is no problem with migration of tritium to the aquifer.

  17. Materials for fire resistant passenger seats in aircraft

    Science.gov (United States)

    Tesoro, G.; Moussa, A.

    1980-01-01

    The paper considers the selection of cushioning foam and upholstery fabric materials for aircraft passenger seats. Polyurethane, polychloroprene, polyimide, and polyphosphazene are the foam materials considered; and a variety of commercial and developmental fabrics (including wool, cotton, synthetics, and blends) are examined. Viable approaches to the design of fire-resistant seat assemblies are indicated. Results of an experimental laboratory study of fabrics and fabric/foam assemblies exposed to external point-source radiative heat flux are discussed.

  18. Fire-resistant materials for aircraft passenger seat construction

    Science.gov (United States)

    Fewell, L. L.; Tesoro, G. C.; Moussa, A.; Kourtides, D. A.

    1979-01-01

    The thermal response characteristics of fabric and fabric-foam assemblies are described. The various aspects of the ignition behavior of contemporary aircraft passenger seat upholstery fabric materials relative to fabric materials made from thermally stable polymers are evaluated. The role of the polymeric foam backing on the thermal response of the fabric-foam assembly is also ascertained. The optimum utilization of improved fire-resistant fabric and foam materials in the construction of aircraft passenger seats is suggested.

  19. The Influence of Tractor-Seat Height above the Ground on Lateral Vibrations

    Directory of Open Access Journals (Sweden)

    Jaime Gomez-Gil

    2014-10-01

    Full Text Available Farmers experience whole-body vibrations when they drive tractors. Among the various factors that influence the vibrations to which the driver is exposed are terrain roughness, tractor speed, tire type and pressure, rear axle width, and tractor seat height above the ground. In this paper the influence of tractor seat height above the ground on the lateral vibrations to which the tractor driver is exposed is studied by means of a geometrical and an experimental analysis. Both analyses show that: (i lateral vibrations experienced by a tractor driver increase linearly with tractor-seat height above the ground; (ii lateral vibrations to which the tractor driver is exposed can equal or exceed vertical vibrations; (iii in medium-size tractors, a feasible 30 cm reduction in the height of the tractor seat, which represents only 15% of its current height, will reduce the lateral vibrations by around 20%; and (iv vertical vibrations are scarcely influenced by tractor-seat height above the ground. The results suggest that manufacturers could increase the comfort of tractors by lowering tractor-seat height above the ground, which will reduce lateral vibrations.

  20. Tune measurement in the NSLS booster synchrotron

    International Nuclear Information System (INIS)

    Blum, E.B.; Nawrocky, R.

    1993-01-01

    The NSLS booster synchrotron can accelerate an electron beam from approximately 80 to 750 MeV in 0.7 sec. The betatron tunes can change during acceleration by as much as 0.1 units, causing beam loss as they cross resonance lines. Precise measurements with a conventional swept spectrum analyzer have always been difficult because of the rapid variation of tune as the magnets are ramped. We are now using a system based on a Tektronix 3052 digital spectrum analyzer that can obtain a complete frequency spectrum over a 10 MHz bandwidth in 200 μsec. Betatron oscillations are stimulated for the measurements by applying white noise to the beam through stripline electrodes. We will describe the instrumentation, our measurements of tune as a function time during the acceleration cycle, and the resulting improvements to the booster operation

  1. Musculoskeletal analysis of driving fatigue: The influence of seat adjustments

    DEFF Research Database (Denmark)

    Majid, Noor Aliah binti Abdul; Abdullah, Mohd Fareez Edzuan; Jamaludin, Mohd Syahmi

    2013-01-01

    Main causes for discomfort experienced by vehicle drivers during driving were investigated using a rigid-body model originally developed in the AnyBody Modeling System [1]. The interactions between the human body and the car-seat in various combinations of seat-pan/backrest inclinations and the e...

  2. An Active Seat Controller with Vehicle Suspension Feedforward and Feedback States: An Experimental Study

    Directory of Open Access Journals (Sweden)

    Abdulaziz Alfadhli

    2018-04-01

    Full Text Available Active seat suspensions can be used to reduce the harmful vertical vibration of a vehicle’s seat by applying an external force using a closed loop controller. Many of the controllers found in the literature are difficult to implement practically, because they are based on using unavailable or difficult and costly measurements. This paper presents both simulation and experimental studies of five novel, simple, and cost-effective control strategies to be used for an active seat suspension in order to improve ride comfort at low frequencies below 20 Hz. These strategies use available and measurable feedforward (preview information states from the vehicle secondary suspension, as well as feedback states from the seat suspension, together with gains optimised to minimise the occupant vibration. The gains were optimised using a genetic algorithm (GA, with a fitness function based on the seat effective amplitude transmissibility (SEAT factor. Constraints on the control force and the seat suspension stroke were also included in the optimisation algorithm. Simulation and laboratory experimental tests were carried out to assess the performance of the proposed controllers according to the ISO 2631-1 standard, in both the frequency and time domains with a range of different road profiles. The experimental tests were performed using a multi-axis simulation table (MAST and a physical active seat suspension configured as a hardware-in-loop (HIL simulation with a virtual linear quarter vehicle model (QvM. The results demonstrate that the proposed controllers substantially attenuate the vertical vibration at the driver’s seat compared with both a passive and a proportional-integral-derivative (PID active seat suspension and thus improve ride comfort together with reducing vibration-linked health risks. Moreover, experimental results show that employing both feedforward information and feedback vehicle body and seat acceleration signals in the controller

  3. Airline seat inventory control benefiting from currency differentials to enhance revenues

    Directory of Open Access Journals (Sweden)

    C.E. Love

    2003-12-01

    Full Text Available The purpose of this paper is to develop an airline seat inventory control model which will capitalise on currency differentials that exist between city pairs. The approach taken here is to maximise Expected Marginal Seat Revenues as proposed by Belobaba for non-nested fare classes. the basic Expected Marginal Seat Revenue model is extended to explicitly include the effects of overbooking. Data from the South African Airways return flight between Cape Town and London is utilised to demonstrate the model.

  4. Development of Methodology to Gather Seated Anthropometry Data in a Microgravity Environment

    Science.gov (United States)

    Rajulu, Sudhakar; Young, Karen; Mesloh, Miranda

    2010-01-01

    The Constellation Program is designing a new vehicle based off of new anthropometric requirements. These requirements specify the need to account for a spinal elongation factor for anthropometric measurements involving the spine, such as eye height and seated height. However, to date there is no data relating spinal elongation to a seated posture. Only data relating spinal elongation to stature has been collected in microgravity. Therefore, it was proposed to collect seated height in microgravity to provide the Constellation designers appropriate data for their analyses. This document will describe the process in which the best method to collect seated height in microgravity was developed.

  5. Child Passenger Safety (A Cup of Health with CDC)

    Centers for Disease Control (CDC) Podcasts

    2016-09-29

    Proper installation and use of car seats and booster seats for child passengers can save their lives. CDC recommends drivers ensure children are always buckled up. In this podcast, Bethany West discusses how to keep young passengers as safe as possible.  Created: 9/29/2016 by MMWR.   Date Released: 9/29/2016.

  6. Design Method for Fast Switching Seat Valves for Digital Displacement Machines

    DEFF Research Database (Denmark)

    Roemer, Daniel Beck; Johansen, Per; Pedersen, Henrik C.

    2014-01-01

    corresponding to the piston movement, which has been shown to facilitate superior part load efficiency combined with high bandwidth compared to traditional displacement machines. However, DD machines need fast switching on-off valves with low pressure loss for efficient operation, especially in fast rotating......Digital Displacement (DD) machines are upcoming technology where the displacement of each pressure chamber is controlled electronically by use of two fast switching seat valves. The effective displacement and operation type (pumping/motoring) may be controlled by manipulating the seat valves...... method for DD seat valves are presented, taking into account the significant aspects related to obtaining efficient DD valves with basis in a given DD machine specifications. The seat area is minimized and the stroke length is minimized to obtain fast switching times while considering the pressure loss...

  7. The seating mechanics of head-neck modular tapers in vitro: Load-displacement measurements, moisture, and rate effects.

    Science.gov (United States)

    Ouellette, Eric S; Shenoy, Aarti A; Gilbert, Jeremy L

    2018-04-01

    The mechanically assisted crevice corrosion performance of head-neck modular tapers is a significant concern in orthopedic biomaterials. Fretting crevice corrosion processes in modular tapers are thought to be influenced by a wide array of factors including seating mechanics of the junction, hence there is a need for in vitro test methods that can assess their performance. This study presented a test method to directly measure the load-displacement seating mechanics of modular tapers and used this method to compare the seating mechanics for different tapers, moisture, seating loads and seating rates. Seating mechanics were explored whereby the instantaneous load-displacement behavior of the head seating onto the neck is captured and used to define the mechanics of seating. Two distinct taper design/material combinations were assembled wet or dry using axially applied loads (500, 1,000, 2,000, and 4,000 N) at two loading rates of 100 and 10 4  N/s (n = 5 for each condition) using a servohydraulic test frame. The results showed that pull-off strength scaled with seating load and ranged between 43% and 68% of seating load depending on sample and wetness. Tapers seated wet had higher pull-off strengths (2,200 ± 300 N) than those seated dry (1,800 ± 200 N, p mechanics (load-displacement plots) varied due to sample type and due to wetness with differences in seating energy, seating stiffness, and seating displacement. These results show the detailed mechanics of seating during assembly and provide significant insight into the complex interplay of factors associated with even "ideal" seating (axial, quasistatic) loading. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:1164-1172, 2018. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc.

  8. Beam current monitoring in the AGS Booster and its transfer lines

    International Nuclear Information System (INIS)

    Witkover, R.L.; Zitvogel, E.; Castillo, V.

    1991-01-01

    The new AGS Booster is designed to accelerate low intensity polarized protons and heavy ions, and high intensity protons. The wide range of beam parameters and the vacuum, thermal and radiation environment, presented challenges in the instrumentation design. This paper describes the problems and solutions for the beam current monitors in the Booster and its transport lines. Where available, results of the initial operation will be presented. 11 refs., 3 figs

  9. Study of solid rocket motors for a space shuttle booster. Volume 1: Executive summary

    Science.gov (United States)

    1972-01-01

    The design, development, production, and launch support analysis for determining the solid propellant rocket engine to be used with the space shuttle are discussed. Specific program objectives considered were: (1) definition of engine designs to satisfy the performance and configuration requirements of the various vehicle/booster concepts, (2) definition of requirements to produce booster stages at rates of 60, 40, 20, and 10 launches per year in a man-rated system, and (3) estimation of costs for the defined SRM booster stages.

  10. Disturbance observer based Takagi-Sugeno fuzzy control for an active seat suspension

    Science.gov (United States)

    Ning, Donghong; Sun, Shuaishuai; Zhang, Fei; Du, Haiping; Li, Weihua; Zhang, Bangji

    2017-09-01

    In this paper, a disturbance observer based Takagi-Sugeno (TS) fuzzy controller is proposed for an active seat suspension; both simulations and experiments have been performed verifying the performance enhancement and stability of the proposed controller. The controller incorporates closed-loop feedback control using the measured acceleration of the seat and deflection of the suspension; these two variables can be easily measured in practical applications, thus allowing the proposed controller to be robust and adaptable. A disturbance observer that can estimate the disturbance caused by friction, model simplification, and controller output error has also been used to compensate a H∞ state feedback controller. The TS fuzzy control method is applied to enhance the controller's performance by considering the variation of driver's weight during operation. The vibration of a heavy duty vehicle seat is largest in the frequency range between 2 Hz and 4 Hz, in the vertical direction; therefore, it is reasonable to focus on controlling low frequency vibration amplitudes and maintain the seat suspensions passivity at high frequency. Moreover, both the simulation and experimental results show that the active seat suspension with the proposed controller can effectively isolate unwanted vibration amplitudes below 4.5 Hz, when compared with a well-tuned passive seat suspension. The active controller has been further validated under bump and random road tests with both a 55 kg and a 70 kg loads. The bump road test demonstrated the controller has good transient response capabilities. The random road test result has been presented both in the time domain and the frequency domain. When with the above two loads, the controlled seat suspensions root-mean-square (RMS) accelerations were reduced by 45.5% and 49.5%, respectively, compared with a well-tuned passive seat suspension. The proposed active seat suspension controller has great potential and is very practical for application

  11. Adaptive magnetorheological seat suspension for shock mitigation

    Science.gov (United States)

    Singh, Harinder Jit

    This research focuses on theoretical and experimental analysis of an adaptive seat suspension employing magnetorheological energy absorber with the objective of minimizing injury potential to seated occupant of different weights subjected to broader crash intensities. The research was segmented into three tasks: (1) development of magnetorheological energy absorber, (2) biodynamic modeling of a seated occupant, and (3) control schemes for shock mitigation. A linear stroking semi-active magnetorheological energy absorber (MREA) was designed, fabricated and tested for intense impact conditions with piston velocities up to 8 m/s. MREA design was optimized on the basis of Bingham-plastic model (BPM model) in order to maximize the energy absorption capabilities at high impact velocities. Computational fluid dynamics and magnetic FE analysis were conducted to validate MREA performance. Subsequently, low-speed cyclic testing (0-2 Hz subjected to 0-5.5 A) and high-speed drop testing (0-4.5 m/s at 0 A) were conducted for quantitative comparison with the numerical simulations. Later, a nonlinear four degrees-of-freedom biodynamic model representing a seated 50th percentile male occupant was developed on the basis of experiments conducted on Hybrid II 50th percentile male anthropomorphic test device. The response of proposed biodynamic model was compared quantitatively against two different biodynamic models from the literature that are heavily implemented for obtaining biodynamic response under impact conditions. The proposed biodynamic model accurately predicts peak magnitude, overall shape and the duration of the biodynamic transient response, with minimal phase shift. The biodynamic model was further validated against 16 impact tests conducted on horizontal accelerator facility at NAVAIR for two different shock intensities. Compliance effects of human body were also investigated on the performance of adaptive seat suspension by comparing the proposed biodynamic model

  12. [Paresthesia and spinal anesthesia for cesarean section: comparison of patient positioning].

    Science.gov (United States)

    Palacio Abizanda, F J; Reina, M A; Fornet, I; López, A; López López, M A; Morillas Sendín, P

    2009-01-01

    To determine the incidence of paresthesia during lumbar puncture performed with the patient in different positions. A single-blind prospective study of patients scheduled for elective cesarean section, randomized to 3 groups. In group 1 patients were seated in the direction of the long axis of the table, with heels resting on the table. In group 2 they were seated perpendicular to the long axis of the table, with legs hanging from the table. In group 3 they were in left lateral decubitus position. Lumbar punctures were performed with a 27-gauge Whitacre needle. One hundred sixty-eight patients (56 per group) were enrolled. Paresthesia occurred most often in group 3 (P = .009). We observed no differences in blood pressure after patients moved from decubitus position to the assigned position. Nor did we observe between-group differences in blood pressure according to position taken during puncture. Puncture undertaken with the patient seated, heels on the table and knees slightly bent, is associated with a lower incidence of paresthesia than puncture performed with the patient seated, legs hanging from the table. Placing the patient's heels on the table requires hip flexion and leads to anterior displacement of nerve roots in the dural sac. Such displacement would increase the nerve-free zone on the posterior side of the sac, thereby decreasing the likelihood of paresthesia during lumbar puncture. A left lateral decubitus position would increase the likelihood of paresthesia, possibly because the anesthetist may inadvertently not follow the medial line when inserting the needle.

  13. OPTIMASI DAYA MESIN DAN KONSUMSI BAHAN BAKAR MESIN TOYOTA SERI 5K MELALUI PENGGUNAAN PENGAPIAN BOOSTER

    Directory of Open Access Journals (Sweden)

    Mardani Ali Sera

    2015-10-01

    Full Text Available Proses pembakaran adalah proses secara fisik yang terjadi di dalam silinder. Proses pembakaran dimulai pada saat busi memercikkan bunga api hingga terjadi proses pembakaran. Dalam penelitian ini digunakan metode eksperimen yaitu membandingkan daya dan konsumsi bahan bakar antara pengapian standar dengan pengapian menggunakan booster. Berdasarkan data hasil uji coba perbandingan antara sistem pengapian standar dengan pengapian yang menggunakan booster dengan objek penelitian mesin Toyota seri 5K diketahui adanya kenaikan 2.61% daya menjadi 27.723 kW dari 27.17 kW antara sistem pengapian standar dengan pengapian yang menggunakan booster pada putaran mesin 2400 rpm. Sedangkan prosentase kenaikan rerata daya sebesar 2.79 %. Penggunaan booster juga membuat penggunaan konsumsi bahan bakar spesifik (sfc antara sistem pengapian standar dengan pengapian yang menggunakan booster. Prosentase penurunan rerata konsumsi bahan bakar spesifik (sfc sebesar 6.99%. Pada sistem pengapian yang menggunakan booster, sfc minimum sebesar 0.219 kg/kWh pada putaran mesin 2200 rpm. Pada pengapian standar sfc minimum sebesar 0.231 kg/kWh pada putaran mesin 2400 rpm.

  14. Comparison of Organ Location, Morphology, and Rib Coverage of a Midsized Male in the Supine and Seated Positions

    Directory of Open Access Journals (Sweden)

    Ashley R. Hayes

    2013-01-01

    Full Text Available The location and morphology of abdominal organs due to postural changes have implications in the prediction of trauma via computational models. The purpose of this study is to use data from a multimodality image set to devise a method for examining changes in organ location, morphology, and rib coverage from the supine to seated postures. Medical images of a male volunteer (78.6±0.77 kg, 175 cm in three modalities (Computed Tomography, Magnetic Resonance Imaging (MRI, and Upright MRI were used. Through image segmentation and registration, an analysis between organs in each posture was conducted. For the organs analyzed (liver, spleen, and kidneys, location was found to vary between postures. Increases in rib coverage from the supine to seated posture were observed for the liver, with a 9.6% increase in a lateral projection and a 4.6% increase in a frontal projection. Rib coverage area was found to increase 11.7% for the spleen. Morphological changes in the organs were also observed. The liver expanded 7.8% cranially and compressed 3.4% and 5.2% in the anterior-posterior and medial-lateral directions, respectively. Similar trends were observed in the spleen and kidneys. These findings indicate that the posture of the subject has implications in computational human body model development.

  15. Integral Ramjet Booster Demonstration Program

    Science.gov (United States)

    1975-02-01

    vibration loads before motor firing at -65, +70, and +1650F, (2) The chambers are fabricated from roll and welded ( TIG ) L-605 sheet that is cold...Typical Integral Booster Internal Configuration Keyhole Grain Pressure and Thrust Versus Time (+700F, Sea Level) Keyhole Grain Pressure and...Thrust Versus Time (+1650F, Sea Level) Keyhole Grain Pressure and Thrust Versus Time (-65^, Sea Level) Radial-Slot Grain Design Radial-Slot Grain

  16. Injection system of teh SSC Medium Energy Booster

    International Nuclear Information System (INIS)

    Mao, N.; Gerig, R.; McGill, J.; Brown, K.

    1994-04-01

    The Medium Energy Booster (MEB) is the third of the SSCL accelerators and the largest of the resistive magnet synchrotrons. It accelerates protons from an injection momentum of 12 GeV/c to a top momentum of 200 GeV/c. A beam injection system has been designed to inject the beam transferred from the Low Energy Booster onto the MEB closed orbit in the MEB injection insertion region. The beam is injected via a vertical bending Lambertson septum magnet and a horizontal kicker with appropriate matching and very little beam loss and emittance dilution. The beam optics of the injection system is described in this paper. The required parameters of the Lambertson septum magnet and the injection kicker are given

  17. A study on mechanism of wear on body seat in nozzle of diesel fuel injector

    Energy Technology Data Exchange (ETDEWEB)

    Jeonggee, Son; Yamashita, Toru; Sato, Susumu; Kosaka, Hidenori; Masuko, Masabumi [Tokyo Institute of Technology (Japan)

    2013-06-01

    Wear of nozzle's body seat of diesel fuel injector, which is caused by the collision of needle on the body seat in a nozzle, affects fuel spray behaviors and injection characteristics. Recently, to reduce the wear of body seat, DLC nozzles are widely used. The DLC on the needle which is called diamond-like carbon has a certain effect in reducing wear of body seat. However, disallowable wear is reported at limited engine operating conditions. Moreover, the wear mechanism of body seat with DLC coated needle has not been made clear yet. In this study, the influence of temperature of the body seat and fuel property on the wear of DLC nozzle was investigated with a newly developed wear testing device which was constructed based on common-rail injection system. Worn surfaces of body seat were observed by FE-SEM, laser scanning microscope and EPMA. The obtained results from the measurements show that DLC nozzle has much less wear amount than non-DLC nozzle on the body seat and the corrosive wear effect is suppressed with DLC nozzle. (orig.)

  18. [Safety and immunogenicity of a 7-valent pneumococcal conjugate vaccine (Prevenar) booster dose in healthy Chinese toddlers].

    Science.gov (United States)

    Li, Rong-cheng; Li, Feng-xiang; Li, Yan-ping

    2009-06-01

    To evaluate the safety and immunogenicity of the booster dose of 7 valent pneumococcal conjugate vaccine (PCV7) to the healthy Chinese toddlers who had received 3 primary doses. Four hundred and eighty-eight Chinese toddlers received a booster dose of PCV7 at age of 12-15 months following a primary series of the vaccine given at ages 3, 4, 5 months separately with Diphtheria Tetanus Acellular Pertussis Combined Vaccine (DTaP) in Group 1 or concurrently with DTaP in Group 2. Following the booster dose immunization, each subject was followed up for 30 days to observe the safety of the vaccine. Blood samples were taken from a subset of subjects prior and post 30 days the booster dose immunization to evaluate immunogenicity. A high proportion of subjects in Group 1 (89%) and Group 2 (91%) remained afebrile after the booster dose. Local reactions to the PCV7 booster dose were generally mild. For each serotype, the rise in GMC (post-/pre-vaccination) showed a statistically significant difference (P<0.0001) between both groups. PCV7 administered as a booster dose is generally safe, well tolerate, and immunogenic in healthy Chinese toddlers.

  19. 49 CFR 571.209 - Standard No. 209; Seat belt assemblies.

    Science.gov (United States)

    2010-10-01

    ... seat belt assembly to fit the user, including such hardware that may be integral with a buckle... the proper use of the assembly, stressing particularly the importance of wearing the assembly snugly... of Standard No. 208. (a)(1) A manual seat belt assembly, which is subject to the requirements of S5.1...

  20. Analysis of resonance-driving imperfections in the AGS Booster

    International Nuclear Information System (INIS)

    Gardner, C.; Shoji, Y.; Danby, G.; Glenn, J.W.; Jackson, G.J.; Soukas, A.; van Asselt, W.; Whalen, C.

    1994-01-01

    At the design intensity of 1.5 x 10 13 ppp, the space charge tune shift in the AGS Booster at injection has been estimated to be about 0.35. The beam tunes are therefore spread over many lower order resonance lines and the associated stopbands must be corrected in order to minimize the amplitude growth due to resonance excitation. This requires proper compensation of the resonance-driving harmonics which result from random magnetic field errors. The observation and correction of second and third order resonance stopbands in the AGS Booster is reviewed, and an analysis of magnetic field imperfections based on the required corrections is given

  1. Measured longitudinal beam impedance of booster gradient magnets; TOPICAL

    International Nuclear Information System (INIS)

    James L Crisp and Brian J. Fellenz

    2001-01-01

    The Booster gradient magnets have no vacuum pipe which forces the beam image current to flow along the laminated pole tips. Both D and F style magnets were measured with a stretched wire to determine the longitudinal beam impedance caused by these laminations. Results are compared to calculations done 30 years ago. The inductive part of the magnet impedance is interesting because it partially compensates for the negative inductance effects of space charge on the beam. An R/L circuit consisting of 37K(center d ot) in parallel with between 40 and 100uH is a reasonable approximation to the total impedance of Booster magnet laminations

  2. Observation and correction of resonance stopbands in the AGS Booster

    International Nuclear Information System (INIS)

    Gardner, C.; Shoji, Y.; Ahrens, L.; Glenn, J.W.; Lee, Y.Y.; Roser, T.; Soukas, A.; van Asselt, W.; Weng, W.T.

    1993-01-01

    At the design intensity of 1.5 x 10 13 ppp, the space charge tune shift in the AGS Booster at injection has been estimated to be about 0.35. Therefore, the beam is spread over may lower order resonance lines and the stopbands have to be corrected to minimize the amplitude growth by proper compensation of the driving harmonics resulting from random errors. The observation and correction of second and third order resonance stopbands in the AGS Booster, and the establishment of a favorable operating point at high intensity are discussed

  3. Development of a multi-body nonlinear model for a seat-occupant system

    Science.gov (United States)

    Azizi, Yousof

    A car seat is an important component of today's cars, which directly affects ride comfort experienced by occupants. Currently, the process of ride comfort evaluation is subjective. Alternatively, the ride comfort can be evaluated by a series of objective metrics in the dynamic response of the occupant. From previous studies it is well known that the dynamic behavior of a seat-occupant system is greatly affected by soft nonlinear viscoelastic materials used in the seat cushion. Therefore, in this research, especial attention was given to efficiently modeling the behavior of seat cushion. In the first part of this research, a phenomenological nonlinear viscoelastic foam model was proposed and its ability to capture uniaxial behavior of foam was investigated. The model is based on the assumption that the total stress can be decomposed into the sum of a nonlinear elastic component, modeled by a higher order polynomial of strain, and a nonlinear hereditary type viscoelastic component. System identification procedures were developed to estimate the model parameters using uniaxial cyclic compression data from experiments conducted at different rates on two types of low density polyurethane foams and three types of high density CONFOR foams. The performance of the proposed model was compared to that of other traditional continuum models. For each foam type, it was observed that lower order models are sufficient to describe the uniaxial behavior of the foam compressed at different rates. Although, the estimated model parameters were functions of the input strain rate. Alternatively, higher order comprehensive models, with strain independent parameters, were estimated as well. The estimated comprehensive model predicts foam responses under different compression rates. Also, a methodology was proposed to predict the stress-response of a layered foam system using the estimated models of each foam in the layers. Next, the estimated foam model was incorporated into a single

  4. Vertical septum magnets for distributing the beam to the 4 PS Booster rings

    CERN Multimedia

    Ordan, Julien Marius

    2017-01-01

    To facilitate H- injection from Linac4 to the PS Booster via the transfer line the BI.SMV10 (Booster Injection Septum Magnet Vertical) provides the vertical deflection of the 160 MeV H- beam to rings 1, 2 and 4 of the Booster. Currently this system is capable of deflecting 50 MeV protons and comprises an assembly of ferrite type magnets in an “omega” section vacuum tank (see fig. 1). The current system shall be replaced with a UHV compatible vacuum chamber incorporating 3 sets of double septum magnets, pulsed from 3 individual power supplies via transformers with 12:1 ratio.

  5. La nuova sfida di SEAT Pagine Gialle

    Directory of Open Access Journals (Sweden)

    Leonardo Landini

    2008-03-01

    Full Text Available SEAT Pagine Gialle’s new challengeSEAT Pagine Gialle is a company that for over 80 years has provided information services, search and communication tools.The companies success and notoriety is built on a customer base of about 20 million families and 3 million professional operators with a continually updated technology with which it integrates with detailed geographical information that allows it to reach millions of users every day. The services the company offers include an advanced cartographic web-based search, satellite and aerial photos, the calculation of driving instructions, weather forecasts and traffic information, 360 degree views and the modelling of whole cities in 3D.

  6. Bench measurements of coupling impedance of AGS Booster components

    International Nuclear Information System (INIS)

    Ratti, A.; Shea, T.J.

    1991-01-01

    Quantifying instability thresholds for modern synchrotrons and storage rings requires some knowledge of the accelerator's coupling impedance. To this end, the wire technique has been implemented to measure the longitudinal coupling impedance of AGS Booster devices. The techniques are being refined to allow measurement of RHIC devices at higher frequencies. All the measurements are performed using an HP 8753 Network Analyzer controlled via GPIB by a Macintosh computer. The computer provides an environment for automated data acquisition, data analysis, and report generation. Resistive matches between the 50ω analyzer cables and the 300ω pipe-and-wire structure allow the use of a simple response calibration in the measurement of S21 to 400MHz. Results from ferrite loaded rf cavities, position monitors and kickers are presented. 4 refs., 4 figs

  7. Cineoesophagogastroscintigraphy and positioning therapy of infant gastroesophageal reflux

    International Nuclear Information System (INIS)

    Peyraud, J.; Guillet, J.; Bouix, G.; Brendel, A.J.

    1985-01-01

    During this prospective study, using cineoesophagogastroscintigraphy carried out in 27 infants under seven months of age, the positioning of the infants in the infant seat for the treatment of the gastroesophageal reflux was not detrimental in comparison to prone positioning [fr

  8. Cineoesophagogastroscintigraphy and positioning therapy of infant gastroesophageal reflux

    Energy Technology Data Exchange (ETDEWEB)

    Peyraud, J.; Guillet, J.; Bouix, G.; Brendel, A.J.

    1985-01-01

    During this prospective study, using cineoesophagogastroscintigraphy carried out in 27 infants under seven months of age, the positioning of the infants in the infant seat for the treatment of the gastroesophageal reflux was not detrimental in comparison to prone positioning.

  9. Cabling design of booster and storage ring construction progress of TPS

    International Nuclear Information System (INIS)

    Wong, Y.-S.; Liu, K.-B.; Liu, C.-Y.; Wang, B.-S.

    2017-01-01

    The 2012 Taiwan Photon Source (TPS) cable construction project started after 10 months to complete the cable laying and installation of power supply. The circumference of the booster ring (BR) is 496.8 m, whereas that of the storage ring (SR) is 518.4 m. Beam current is set to 500 mA at 3.3 GeV. The paper on grounding systems discusses the design of the ground wire (< 0.2 Ω) with low impedance, power supply of the accelerator and cabling tray. The flow and size of the ground current are carefully evaluated to avoid grounded current from flowing everywhere, which causes interference problems. In the design of the TPS, special shielding will be established to isolate the effects of electromagnetic interference on the magnet and ground current. Booster ring dipoles are connected by a series of 54-magnet bending dipole; the cable size of its stranded wire measures 250 mm"2, with a total length of 5000 m. Booster ring and storage ring quadrupoles have 150 magnets; the cable size of their stranded wire is 250 mm"2, with a total length of 17000 m. Storage ring dipole consists of 48 magnets; the cable size of its stranded wire is 325 mm"2, with a total length of 6000 m. This study discusses the power supply cabling design of the storage ring and booster ring construction progress of TPS. The sections of this paper are divided into discussions of the construction of the control and instrument area, cabling layout of booster ring and storage ring, as well as the installation and commission machine. This study also discusses the use of a high-impedance meter to determine the effect of cabling insulation and TPS power supply machine on energy transfer to ensure the use of safe and correct magnet.

  10. Designing Train Passenger Seat by Kansei Engineering in Indonesia

    Directory of Open Access Journals (Sweden)

    Hapsari Sakya Nabila

    2017-01-01

    Full Text Available Public transport adoption is still major problem in Indonesia. Integrating impression and emotion to service may change the image of public transport, leading to fast adoption rate. As product development technique, Kansei Engineering is well known to facilitate that integration. This paper communicates the implementation of Kansei Engineering (KE in designing train passenger seat in Indonesia. The train between Bandung-Solo (8 hours journey was chosen to be the investigated object. The train was selected to be refurbished by introducing a new passenger seat design, emphasizing on the improvement of passenger experience. As the first step of KE type I technique, travel experience of the existing passengers were taken into the consideration for selecting Kansei words. It was found that the relevant Kansei words to design passenger train seat in Indonesia were: comfort, people-friendly, multifunction, safe, soft, spacious, relaxing, superior, maintainable, strong, producible, minimalist, attractive, modern, unique, and durable. Upon understanding the semantic meaning of those words, physical properties and technical specification were produced by consulting to the related members. Finally, a passenger seat with synthetic leather cover, modular design, foldable table, individual power point, bluesilver color, and adjusted to Indonesian’s anthropometry data was proposed as the final design

  11. Optimum design of automobile seat using statistical design support system; Tokeiteki sekkei shien system no jidoshayo seat eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Kashiwamura, T [NHK Spring Co. Ltd., Yokohama (Japan); Shiratori, M; Yu, Q; Koda, I [Yokohama National University, Yokohama (Japan)

    1997-10-01

    The authors proposed a new practical optimum design method called statistical design support system, which consists of five steps: the effectivity analysis, reanalysis, evaluation of dispersion, the optimiza4ion and evaluation of structural reliability. In this study, the authors applied the present system to analyze and optimum design of an automobile seat frame subjected to crushing. This study should that the present method could be applied to the complex nonlinear problems such as large deformation, material nonlinearity as well as impact problem. It was shown that the optimum design of the seat frame has been solved easily using the present system. 6 refs., 5 figs., 5 tabs.

  12. Child car seats – a habitat for house dust mites and reservoir for harmful allergens

    Directory of Open Access Journals (Sweden)

    David Clarke

    2015-02-01

    Full Text Available [b]Introduction and objective[/b]. House dust mites produce allergens which can cause or aggravate diseases such as asthma, eczema and rhinitis. The objectives of this study are to quantify typical house dust mite and Der p 1 allergen levels in child car seats, and to determine external variables that may influence mite populations in cars. [b]Materials and Methods[/b]. Dust samples were collected from the child car seats and driver seats of 106 cars using a portable vacuum sampling pump over a two minute sampling period. Mites were counted and identified and results were expressed as mites per gram (mites/g of dust, while Der p 1 content of samples were measured by enzyme-linked immunosorbent assay (ELISA. Questionnaires were completed by participants to identify environmental and behavioural effects on mite populations. Results were analysed using General Linear Model (GLM procedures. [b]Results[/b]. Twelve species of mites, of which nine are known to produce harmful allergens, were recorded from 212 dust samples. Over 80% of drivers’ seats and over 77% of child car seats harboured dust mites with a significant correlation (p = 0.001 between the mites/g of dust and Der p 1 content recovered from each seat. A mean of 53 mites/g of dust per seat was recovered, with a mean Der p 1 level of 1.1µg/g. Over 12% of driver seats and 15% of child car seats contained house dust mite levels sufficient to be risk factors for sensitisation and allergic reactions. [b]Conclusions[/b]. Child car seats and driver seats are habitats to a range of mite species which can be present in sufficient concentrations to cause or aggravate allergen related illnesses in individuals who are genetically predisposed.

  13. [The use of seatbelts and child seats in drivers and passengers of motor vehicles in four metropolitan areas in Mexico].

    Science.gov (United States)

    Cervantes-Trejo, Arturo; Leenen, Iwin

    2015-01-01

    To estimate the rate of seatbelt and child seat use in drivers and passengers of motor vehicles in four metropolitan areas in Mexico (Guadalajara, León, Monterrey and Mexico City). To evaluate the impact of the Mexican Initiative for Road Safety (IMESEVI) in this respect. Data were collected at the start of IMESEVI (June 2008) and one year after the program's implementation (October 2009) in the four participating metropolitan areas. In particular, the use of seatbelts and child seats was observed in occupants of automobiles, station wagons, and light trucks. The sample included 28,412 (pre) and 52,274 (post) individuals, of which 1,454 (pre) and 1,679 (post) were younger than five years old. The data analysis was based on a hierarchical logistic model. Globally, the probability of using either safety device is 46% (95% CI: 43-49%) at baseline and 52% (95% CI: 48-55%) at the post measurement, with large differences, though, among the four participating metropolitan areas. Factors that significantly affect their use include the individual's position in the vehicle, the type and age of the vehicle, and the individual's sex. Child seat use is very limited. At baseline, about 17% (95% CI: 11-25%) of children below five years old travelled in a special seat, with this number increasing to 26% (95% CI: 19-34%) after the implementation of IMESEVI. Child seat use for children above four years is virtually nonexistent. Continued efforts are required to raise the public awareness of the importance of using safety devices, especially for passengers in the back of the car as well as with respect to the use of adapted seats for small children.

  14. Flow Characteristics and Sizing of Annular Seat Valves for Digital Displacement Machines

    Directory of Open Access Journals (Sweden)

    Christian Nørgård

    2018-01-01

    Full Text Available This paper investigates the steady-state flow characteristics and power losses of annular seat valves for digital displacement machines. Annular seat valves are promising candidates for active check-valves used in digital displacement fluid power machinery which excels in efficiency in a broad operating range. To achieve high machine efficiency, the valve flow losses and the required electrical power needed for valve switching should be low. The annular valve plunger geometry, of a valve prototype developed for digital displacement machines, is parametrized by three parameters: stroke length, seat radius and seat width. The steady-state flow characteristics are analyzed using static axi-symmetric computational fluid dynamics. The pressure drops and flow forces are mapped in the valve design space for several different flow rates. The simulated results are compared against measurements using a valve prototype. Using the simulated maps to estimate the flow power losses and a simple generic model to estimate the electric power losses, both during digital displacement operation, optimal designs of annular seat valves, with respect to valve power losses, are derived under several different operating conditions.

  15. Compensation of dogleg effect in Fermilab Booster

    CERN Document Server

    Xiao Biao Huang

    2003-01-01

    The edge focusing of dogleg magnets in Fermilab Booster has been causing severe distortion to the horizontal linear optics. The doglegs are vertical rectangular bends, therefore the vertical edge focusing is canceled by body focusing and the overall effect is focusing in the horizontal plane. The maximum horizontal beta function is changed from 7m to 46.9m and maximum dispersion from 3.19m to 6.14m. Beam size increases accordingly. This is believed to be one of the major reasons of beam loss. In this technote we demonstrate that this effect can be effectively corrected with Booster's quadrupole correctors in short straight sections (QS). There are 24 QS correctors which can alter horizontal linear optics with negligible perturbation to the vertical plane. The currents of correctors are determined by harmonic compensation, i.e., cancellation of dogleg's harmonics that are responsible for the distortion with that of QS correctors. By considering a few leading harmonics, the ideal lattice can be partly restored....

  16. Design and evaluation of a suspension seat to reduce vibration exposure of subway operators: a case study.

    Science.gov (United States)

    Marcotte, Pierre; Beaugrand, Sylvie; Boutin, Jérôme; Larue, Christian

    2010-01-01

    Subway operators have complained about discomfort caused by whole-body vibration. To address this problem, a suspension seat with extensive ergonomic features has been adapted to the confined space of the subway operator cab. The suspension was modified from an existing suspension in order to reduce the dominant frequency of the subway vertical vibration (2.4 Hz). The suspension seat has been extensively tested on a vertical hydraulic shaker. These tests have shown that the SEAT value was lower for a higher vibration level, for higher subject weight, and for the suspension adjusted at median height. The seat also produces a lower SEAT value when there was a predominance of the 6 Hz vibration component. The horizontal seat adjustments had no influence on the suspension SEAT value. Removing the suspension damper also decreases the SEAT value for all the tested configurations. The final version of the suspension seat prototype was validated during normal subway operation with 19 different operators having weight in the 5th, 50th and 95th percentile of the operator population. Accelerations were measured with triaxial accelerometers at the seat cushion, above the suspension and on the floor. In addition to the vibration measurements, each operator was asked about his perceived discomfort from vibration exposure. Globally, the suspension seat attenuated the vertical vibration (SEAT values from 0.86 to 0.99), but discomfort due to amplification of the 2.4 Hz component occurred when the suspension height was adjusted at the minimum, even when the global weighted acceleration was lower (SEAT value < 1). These results suggest that in order to reduce the discomfort caused by whole-body vibration, the transmissibility of the seat should also be considered, in particular when there is a dominant frequency in the vibration spectra.

  17. Blood Pressure Directed Booster Trainings Improve Intensive Care Unit Provider Retention of Excellent Cardiopulmonary Resuscitation Skills.

    Science.gov (United States)

    Wolfe, Heather; Maltese, Matthew R; Niles, Dana E; Fischman, Elizabeth; Legkobitova, Veronika; Leffelman, Jessica; Berg, Robert A; Nadkarni, Vinay M; Sutton, Robert M

    2015-11-01

    Brief, intermittent cardiopulmonary resuscitation (CPR) training sessions, "Booster Trainings," improve CPR skill acquisition and short-term retention. The objective of this study was to incorporate arterial blood pressure (ABP) tracings into Booster Trainings to improve CPR skill retention. We hypothesized that ABP-directed CPR "Booster Trainings" would improve intensive care unit (ICU) provider 3-month retention of excellent CPR skills without need for interval retraining. A CPR manikin creating a realistic relationship between chest compression depth and ABP was used for training/testing. Thirty-six ICU providers were randomized to brief, bedside ABP-directed CPR manikin skill retrainings: (1) Booster Plus (ABP visible during training and testing) versus (2) Booster Alone (ABP visible only during training, not testing) versus (3) control (testing, no intervention). Subjects completed skill tests pretraining (baseline), immediately after training (acquisition), and then retention was assessed at 12 hours, 3 and 6 months. The primary outcome was retention of excellent CPR skills at 3 months. Excellent CPR was defined as systolic blood pressure of 100 mm Hg or higher and compression rate 100 to 120 per minute. Overall, 14 of 24 (58%) participants acquired excellent CPR skills after their initial training (Booster Plus 75% vs 50% Booster Alone, P = 0.21). Adjusted for age, ABP-trained providers were 5.2× more likely to perform excellent CPR after the initial training (95% confidence interval [95% CI], 1.3-21.2; P = 0.02), and to retain these skills at 12 hours (adjusted odds ratio, 4.4; 95% CI, 1.3-14.9; P = 0.018) and 3 months (adjusted odds ratio, 4.1; 95% CI, 1.2-13.9; P = 0.023) when compared to baseline performance. The ABP-directed CPR booster trainings improved ICU provider 3-month retention of excellent CPR skills without the need for interval retraining.

  18. Digital Recovery Sequencer - Advanced Concept Ejection Seats

    National Research Council Canada - National Science Library

    Ross, David A; Cotter, Lee; Culhane, David; Press, Matthew J

    2005-01-01

    .... Continued usage of the Analog Sequencer is undesirable due to limitations with respect to its installed life, electronic component obsolescence, flexibility to accommodate seat safety improvements...

  19. [Use of seat belts and mobile phone while driving in Florence: trend from 2005 to 2009].

    Science.gov (United States)

    Lorini, Chiara; Pellegrino, Elettra; Mannocci, Federico; Allodi, Guendalina; Indiani, Laura; Mersi, Anna; Petrioli, Giuseppe; Santini, Maria Grazia; Garofalo, Giorgio; Bonaccorsi, Guglielmo

    2012-01-01

    to evaluate the trend over time of the use of seat belts by drivers and passengers of cars and vans and the use of hand held mobile phone while driving in Florence from 2005 to 2009. DESIGN, SETTING AND PARTICIPANTS AND MAIN OUTCOME MEASURES: direct observations (58,773 vehicles) have been conducted to detect the use of seat belts by occupants of cars and vans, and the use of mobile phone while driving. It has been carried out correlation analysis between the use of the seat belt by occupants of vehicles and between the simultaneous use of this device and mobile phone while driving.Moreover, it has been carried out time series analysis (ARIMA Box Jenkins) of in the prevalence of the use of seat belts by occupants of vehicles observed, of mobile phone by drivers and the trend of the risk to drive using the mobile phone with unfastened seat belt rather than to drive using the mobile phone with fastened seat belt. seat belts were used on average by 75.7% of drivers, 75.5% of front passengers and 25.1% of rear passengers. The average mobile phone use while driving was 4.5%. Drivers most frequently fasten seat belt if front passengers use it and while they do not use mobile phone. The use of seat belts by drivers and front passengers has not changed over time, whereas the use of mobile phone while driving has significantly increased. The prevalence of using mobile phone with unfastened seat belt rather than to use it with fastened seat belt while driving has significantly decreased over the years, indicating an increase in the use of mobile phone, especially among those who fasten the seat belt. it is necessary to plan and realize stronger interventions in the whole area.

  20. Relationship between postural alignment in sitting by photogrammetry and seated postural control in post-stroke subjects.

    Science.gov (United States)

    Iyengar, Y R; Vijayakumar, K; Abraham, J M; Misri, Z K; Suresh, B V; Unnikrishnan, B

    2014-01-01

    This study was executed to find out correlation between postural alignment in sitting measured through photogrammetry and postural control in sitting following stroke. A cross-sectional study with convenient sampling consisting of 45 subjects with acute and sub-acute stroke. Postural alignment in sitting was measured through photogrammetry and relevant angles were obtained through software MB Ruler (version 5.0). Seated postural control was measured through Function in Sitting Test (FIST). Correlation was obtained using Spearman's Rank Correlation co-efficient in SPSS software (version 17.0). Moderate positive correlation (r = 0.385; p < 0.01) was found between angle of lordosis and angle between acromion, lateral epicondyle and point between radius and ulna. Strong negative correlation (r = -0.435; p < 0.01) was found between cranio-vertebral angle and kyphosis. FIST showed moderate positive correlation (r = 0.3446; p < 0.05) with cranio-vertebral angle and strong positive correlation (r = 0.4336; p < 0.01) with Brunnstrom's stage of recovery in upper extremity. Degree of forward head posture in sitting correlates directly with seated postural control and inversely with degree of kyphosis in sitting post-stroke. Postural control in sitting post-stroke is directly related with Brunnstrom's stage of recovery in affected upper extremity in sitting.

  1. Design and status of the AGS booster accelerator

    International Nuclear Information System (INIS)

    Forsyth, E.B.; Lee, Y.Y.

    1987-01-01

    Comments are given on some areas of the design considered for the AGS Booster Accelerator, including lattice design, energy and repetition rate, injection, radio frequency system, and the vacuum system. The current status is then briefly described

  2. Association Between NCAP Ratings and Real-World Rear Seat Occupant Risk of Injury.

    Science.gov (United States)

    Metzger, Kristina B; Gruschow, Siobhan; Durbin, Dennis R; Curry, Allison E

    2015-01-01

    Several studies have evaluated the correlation between U.S. or Euro New Car Assessment Program (NCAP) ratings and injury risk to front seat occupants, in particular driver injuries. Conversely, little is known about whether NCAP 5-star ratings predict real-world risk of injury to restrained rear seat occupants. The NHTSA has identified rear seat occupant protection as a specific area under consideration for improvements to its NCAP. In order to inform NHTSA's efforts, we examined how NCAP's current 5-star rating system predicts risk of moderate or greater injury among restrained rear seat occupants in real-world crashes. We identified crash-involved vehicles, model year 2004-2013, in NASS-CDS (2003-2012) with known make and model and nonmissing occupant information. We manually matched these vehicles to their NCAP star ratings using data on make, model, model year, body type, and other identifying information. The resultant linked NASS-CDS and NCAP database was analyzed to examine associations between vehicle ratings and rear seat occupant injury risk; risk to front seat occupants was also estimated for comparison. Data were limited to restrained occupants and occupant injuries were defined as any injury with a maximum Abbreviated Injury Scale (AIS) score of 2 or greater. We linked 95% of vehicles in NASS-CDS to a specific vehicle in NCAP. The 18,218 vehicles represented an estimated 6 million vehicles with over 9 million occupants. Rear seat passengers accounted for 12.4% of restrained occupants. The risk of injury in all crashes for restrained rear seat occupants was lower in vehicles with a 5-star driver rating in frontal impact tests (1.4%) than with 4 or fewer stars (2.6%, P =.015); results were similar for the frontal impact passenger rating (1.3% vs. 2.4%, P =.024). Conversely, side impact driver and passenger crash tests were not associated with rear seat occupant injury risk (driver test: 1.7% for 5-star vs. 1.8% for 1-4 stars; passenger test: 1.6% for 5

  3. Design and status of the AGS booster accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Forsyth, E.B.; Lee, Y.Y.

    1987-01-01

    Comments are given on some areas of the design considered for the AGS Booster Accelerator, including lattice design, energy and repetition rate, injection, radio frequency system, and the vacuum system. The current status is then briefly described. (LEW)

  4. Energy-efficient operation of a booster RF system for Taiwan light source operated in top-up mode

    International Nuclear Information System (INIS)

    Yeh, Meng-Shu; Wang, Chaoen; Chang, Lung-Hai; Chung, Fu-Tsai; Yu, Tsung-Chi; Lin, Ming-Chyuan; Chen, Ling-Jhen; Yang, Tz-Te; Chang, Mei-Hsia; Lin, Yu-Han; Tsai, Ming-Hsun; Lo, Chih-Hung; Liu, Zong-Kai

    2015-01-01

    Contemporary light sources operate in a top-up mode to maintain their photon intensity quasi-constant so as to improve significantly the thermal stability of the photon beam and to maximize ultimately the average photon flux at a designed maximum operational beam current. Operating in a top-up mode requires frequent beam injection from the synchrotron booster to the storage ring of the light source, but the injection intervals occupy only a tiny portion of the operational time of the integrated machine. To maintain a high operational reliability, the booster RF system practically operates necessarily under injection conditions around the clock and consumes full electric power whether during top-up injection or not. How to decrease the power consumption of the booster RF system during its stand-by time but not to sacrifice the reliability and availability of the RF system is obviously of fundamental interest for routine operation of the light source in a top-up mode. Here, an energy-efficient operation of a booster RF system adaptive to top-up operation of a light source is proposed that has been developed, realized and integrated into the booster RF system of the Taiwan Light Source (TLS), and routinely operated since the end of year 2008. The klystron cathode current and RF gap voltage of the booster's accelerating RF cavity are both periodically modulated to adapt the injection rhythm during top-up operation, which results in decreased consumption of electric power of the booster RF system by more than 78%. The impact on the reliability and availability of the booster RF system has been carefully monitored during the past five operational years, delivering more than 5000 h scheduled user beam time per year. The booster RF system retains its excellent reliability and availability as previously. Neither a decrease of the service time nor an induced reliability issue from the klystron or any high-power high-voltage component of the transmitter has been

  5. Seat belt use to save face: impact on drivers' body region and nature of injury in motor vehicle crashes.

    Science.gov (United States)

    Han, Guang-Ming; Newmyer, Ashley; Qu, Ming

    2015-01-01

    Seat belt use is the single most effective way to save lives and reduce injuries in motor vehicle crashes. However, some case reports described seat belt use as a double-edged sword because some injuries are related to seat belt use in motor vehicle crashes. To comprehensively understand the effects of seat belt use, we systemically investigated the association between seat belt use and injuries based on anatomic body region and type of injury in drivers involved in motor vehicle crashes. The injury information was obtained by linking crash reports with hospital discharge data and categorized by using the diagnosis codes based on the Barell injury diagnosis matrix. A total of 10,479 drivers (≥15 years) in passenger vehicles involved in motor vehicle crashes from 2006 to 2011 were included in this study. Seat belt use significantly reduced the proportions of traumatic brain injury (10.4% non-seat belt; 4.1% seat belt) and other head, face, and neck injury (29.3% non-seat belt; 16.6% seat belt) but increased the proportion of spine: thoracic to coccyx injury (17.9% non-seat belt; 35.5% seat belt). Although the proportion of spine: thoracic to coccyx injury was increased in drivers with seat belt use, the severity of injury was decreased, such as fracture (4.2% with seat belt use; 22.0% without seat belt use). Furthermore, the total medical charges decreased due to the change of injury profiles in drivers with seat belt use from a higher percentage of fractures (average cost for per case $26,352) to a higher percentage of sprains and/or strains ($1,897) with spine: thoracic to coccyx injury. This study provide a comprehensive picture for understanding the protective effect of seat belt use on injuries based on anatomic body region and type of injury in drivers involved in motor vehicle crashes.

  6. Evaluation of the League General Insurance Company child safety seat distribution program

    Science.gov (United States)

    1982-05-01

    This report presents an evaluation of the child safety seat distribution initiated by the League General Insurance Company in June 1979. The program provides child safety seats as a benefit under the company's auto insurance policies to policy-holder...

  7. Whole-body Vibration Exposure Intervention among Professional Bus and Truck Drivers: A Laboratory Evaluation of Seat-suspension Designs.

    Science.gov (United States)

    Blood, Ryan P; Yost, Michael G; Camp, Janice E; Ching, Randal P

    2015-01-01

    Long-term exposure to seated whole-body vibration (WBV) is one of the leading risk factors for the development of low back disorders. Professional bus and truck drivers are regularly exposed to continuous WBV, since they spend the majority of their working hours driving heavy vehicles. This study measured WBV exposures among professional bus and truck drivers and evaluated the effects of seat-suspension designs using simulated field-collected data on a vibration table. WBV exposures were measured and compared across three different seat designs: an air-ride bus seat, an air-ride truck seat, and an electromagnetically active (EM-active) seat. Air-ride seats use a compressed-air bladder to attenuate vibrations, and they have been in operation throughout the transportation industry for many years. The EM-active seat is a relatively new design that incorporates a microprocessor-controlled actuator to dampen vibration. The vibration table simulated seven WBV exposure scenarios: four segments of vertical vibration and three scenarios that used field-collected driving data on different road surfaces-a city street, a freeway, and a section of rough roadway. The field scenarios used tri-axial WBV data that had been collected at the seat pan and at the driver's sternum, in accordance with ISO 2631-1 and 2631-5. This study found that WBV was significantly greater in the vertical direction (z-axis) than in the lateral directions (x-and y-axes) for each of the three road types and each of the three types of seats. Quantitative comparisons of the results showed that the floor-to-seat-pan transmissibility was significantly lower for the EM-active seat than for either the air-ride bus seat or the air-ride truck seat, across all three road types. This study also demonstrated that seat-suspension designs have a significant effect on the vibrations transmitted to vehicle operators, and the study's results may prove useful in designing future seat suspensions.

  8. Compliance with Use of Seat Belt among Commercial Drivers in a Nigerian Community

    Directory of Open Access Journals (Sweden)

    Oluwole C. Omolase

    2012-06-01

    Full Text Available AIM: This study aimed at determining compliance with use of seat belt among commercial intercity drivers. METHOD: This is a descriptive cross-sectional study conducted in Owo, South West Nigeria among commercial intercity drivers between June and September, 2009. Ethical clearance was obtained from the Ethical Review Committee of Federal Medical Centre, Owo, Ondo State, Nigeria prior to commencement of this study. The permission of the leadership of Road Transport Workers’ Union was also sought and obtained. Ninety intercity commercial drivers out of the estimated one hundred and sixty intercity commercial drivers in the community were enrolled in this study. Informed consent was obtained from each of the respondents. The data obtained was collated and analyzed with SPSS 15.0.1 statistical soft ware version. RESULTS: Ninety respondents were enrolled in this study. The driving experience of the respondents revealed that most respondents: 53 (58.9% had more than 20 years driving experience. Most respondents;78 (86.7% complied with use of seat belt .The main barrier to compliance with seat belt was short trip;28 (50.9%.Most respondents; 67 (74.4%were in support of penalization of defaulters. The major source of awareness about seat belt was Federal Road Safety Corps;59 (65.6%. CONCLUSION: Most respondents complied with use of seat belt. The major barrier to compliance with seat belt was short trip within the community. The Federal Road Safety Corps should enforce compliance with the use of seat belt most especially within communities. [TAF Prev Med Bull 2012; 11(3.000: 281-286

  9. Preliminary study of AC power feeders for AGS booster

    International Nuclear Information System (INIS)

    Meth, M.

    1992-01-01

    It has been proposed that the AGS Heavy Ion/Proton Booster be excited directly from the electric power distribution system without intervening an energy storage buffer such as an MG set or a magnetic energy buffer. The average power requirement of the AGS Booster is less than many single-loads presently housed on the lab site. However, the power swing will be the largest single pulsating load on the lab site. The large power swings will impact on the power grid producing utility-line disturbances such as voltage fluctuations and harmonic generation. Thus, it is necessary to carefully evaluate the quality of the electric power system resulting from the interconnection, such that the utility system is not degraded either on the lab site or at LILCO's substation

  10. The 1.4 GeV PS Booster in its tunnel.

    CERN Multimedia

    Patrice Loïez

    2002-01-01

    The PS Improvement Programme, launched as early as 1964, had a "Booster" as the key element in the quest for higher beam intensity and density. These were limited in the PS at injection of the 50 MeV proton beam from the linac by the incoherent (Laslett-) Q-shift. Boosting the linac beam to 800 MeV would raise the PS intensity limit by an order of magnitude, from 1E12 protons per pulse to 1E13. The main motivation was the supply of intense beams to the ISR. Soon, the Booster proved to be crucial for the neutral current experiment. A unique feature of the Booster are its 4 superposed rings. Its lattice is also unusual: between its 32 bending magnets, every second straight section contains a quadrupole triplet (F,D,F), while the alternate ones are drift spaces (mostly filled with essential components like septa, kickers, RF-cavities, etc.). In each picture we see one of the 16 periods. Following the direction of the beam from right to left: a bending magnet (green); an empty straight section; a bending magnet; ...

  11. Affirmative Action: Reservation Seats untuk Perempuan di Parlemen India

    Directory of Open Access Journals (Sweden)

    Evi Yunita Kurniaty

    2015-12-01

    Full Text Available The study aims to help us understand and analyze women's efforts in the policy-making process to increase their political participation in the constitutional and electoral processes. We can also see the extent to which the values rooted in the patriarchal culture in a society and what can be done and reduce them. Affirmative action is carried out in India by applying the system of reservation seats for women in the Indian Parliament. This is done in India is proven to increase the number of women in the Indian Parliament. By the way there are quotas for women as a strategy for accessing the political arena has growing support among MPs. In this study, Indonesia could get a reservation seats of learning about the system is done. To increase the representation in the "area" is very difficult to be touched by a quota system which is run now, it can be done with reservation seats quota to ensure women's representation in parliament.

  12. Magnet power supply system for the ALS storage ring and booster

    International Nuclear Information System (INIS)

    Jackson, L.T.; Luchini, K.; Lutz, I.

    1993-05-01

    The Magnet Power Supply System is described by specification, design, hardware, and operating experience. A unique system for the one Hz, 1.5 GeV Booster, where the wideband QF and QD power supplies track the dipole current to within 0.1% at injection will be detailed. AC distribution system considerations related to inverting the stored energy of the booster magnet back into power grid will be discussed. The rational for linear correctors and individual quad supplies (225 total units) will be placed within the context of the storage-ring requirements

  13. Ergonomic Analysis of Tricycle Sidecar Seats: Basis for Proposed Standard Design

    Directory of Open Access Journals (Sweden)

    Michael C. Godoy

    2015-12-01

    Full Text Available Ergonomics (also called human factors engineering is the study of human characteristics for the appropriate design of the living and work environment. It is applied in various industrial areas which includes transportation.Tricycle being one of the most common means of public transportation in Lipa City has various adaptations to suit the culture, and environment. The purpose of this study is to analyze the variability in design of the tricycles in Lipa City, Philippines and propose a standard ergonomically designed tricycle sidecar seat for a greater population. The study was conducted at 26 tricycle terminals with 232 tricycle samples within Lipa City proper including the public market area where 400 commuters were given questionnaires to determine the risk factors associated with the existing tricycle sidecar seat design. Anthropometric measurements of 100 males and 100 female commuters were obtained together with the sidecar dimensions of 232 tricycles to substantiate the observed variations in design. Using the design for the average and design for the extremes, it was found out that most of the tricycles in Lipa City, Philippines have inappropriate inclined seat and lowered sidecar seat pan height which can result to leg and abdominal pain; narrowed seat pan depth which caused pressure on buttocks and legs; narrowed backrest width which can cause upper and low back pain; low backrest height that can pose upper back pain; which can also result to abdominal pain; inclined backrest and limited vertical clearance which can cause upper back pain and neck pain. The researcher proposed a sidecar seat design standard which can be used by the Land Transportation Office, and Land Transportation Franchising and Regulatory Board to provide ease, comfort, and convenience to the passengers.

  14. Liquid Rocket Booster (LRB) for the Space Transportation System (STS) Systems Study; Volume 1 - Executive Summary

    National Research Council Canada - National Science Library

    Ware, Larry

    1989-01-01

    ...) solid rocket boosters (SRBs) with liquid rocket boosters (LRBs), Figure 1.0-1. The main objectives of a LRB substitution for the SRB were increased STS safety and reliability and increased payload performance...

  15. Integrated hydraulic booster/tool string technology for unfreezing of stuck downhole strings in horizontal wells

    Science.gov (United States)

    Tian, Q. Z.

    2017-12-01

    It is common to use a jarring tool to unfreeze stuck downhole string. However, in a horizontal well, influenced by the friction caused by the deviated section, jarring effect is poor; on the other hand, the forcing point can be located in the horizontal section by a hydraulic booster and the friction can be reduced, but it is time-consuming and easy to break downhole string using a large-tonnage and constant pull force. A hydraulic booster - jar tool string has been developed for unfreezing operation in horizontal wells. The technical solution involves three elements: a two-stage parallel spring cylinder structure for increasing the energy storage capacity of spring accelerators; multiple groups of spring accelerators connected in series to increase the working stroke; a hydraulic booster intensifying jarring force. The integrated unfreezing tool string based on these three elements can effectively overcome the friction caused by a deviated borehole, and thus unfreeze a stuck string with the interaction of the hydraulic booster and the mechanical jar which form an alternatively dynamic load. Experimental results show that the jarring performance parameters of the hydraulic booster-jar unfreezing tool string for the horizontal wells are in accordance with original design requirements. Then field technical parameters were developed based on numerical simulation and experimental data. Field application shows that the hydraulic booster-jar unfreezing tool string is effective to free stuck downhole tools in a horizontal well, and it reduces hook load by 80% and lessens the requirement of workover equipment. This provides a new technology to unfreeze stuck downhole string in a horizontal well.

  16. Present state of tandem superconductive booster of JAERI

    Energy Technology Data Exchange (ETDEWEB)

    Takeuchi, Suehiro; Matsuda, Makoto; Kanazawa, Shuhei; Yoshida, Tadashi; Ouchi, Isao; Shoji, Tokio [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1996-12-01

    The superconductive booster constructed rear-stage accelerator of the tandem accelerator of the Tokai Research Establishment, JAERI (Japan Atomic Energy Research Institute), was completed in construction of its whole system on October, 1993, and through its beam accelerating test and remodulation its design characteristics were established on September, 1994. From November, 1994 to April, 1995 a repulsion-forming nuclear isolation apparatus was installed to modulate at target room, and was begun to use on June, 1995. The beam reaccelerated at the booster was used mainly for nuclear spectroscopy experiment, a collaborative research was developed using mini-crystal balls made by collecting from University of Tsukuba and so forth. The accelerating part of the booster is a phase independent setting type Linac consisting of 40 niobium superconducting holes with 1/4 wave-length type and 130 MHz in frequency, in which a hole can form 5 MV/m of accelerating electric field for 4 W of radio frequency spent power of 0.75 MV of accelerating voltage per hole, to form 30 MV of voltage in a whole. 4 holes are contained into each 10 cryostats, respectively. In accelerating tests, Si, Cl, Ni, Ge, Ag, I and Au ions are accelerated to establish 30 mV of total accelerating voltage in its design value, which reaches to their expected energy characteristics. Its used days in this year are 25 days after beginning of its use, and operating days of the cooling apparatus was 135 days in total. (G.K.)

  17. Seat Capacity Selection for an Advanced Short-Haul Aircraft Design

    Science.gov (United States)

    Marien, Ty V.

    2016-01-01

    A study was performed to determine the target seat capacity for a proposed advanced short-haul aircraft concept projected to enter the fleet by 2030. This analysis projected the potential demand in the U.S. for a short-haul aircraft using a transportation theory approach, rather than selecting a target seat capacity based on recent industry trends or current market demand. A transportation systems model was used to create a point-to-point network of short-haul trips and then predict the number of annual origin-destination trips on this network. Aircraft of varying seat capacities were used to meet the demand on this network, assuming a single aircraft type for the entire short-haul fleet. For each aircraft size, the ticket revenue and operational costs were used to calculate a total market profitability metric for all feasible flights. The different aircraft sizes were compared, based on this market profitability metric and also the total number of annual round trips and markets served. Sensitivity studies were also performed to determine the effect of changing the aircraft cruise speed and maximum trip length. Using this analysis, the advanced short-haul aircraft design team was able to select a target seat capacity for their design.

  18. History of the ZGS 500 MeV booster.

    Energy Technology Data Exchange (ETDEWEB)

    Simpson, J.; Martin; R.; Kustom, R.

    2006-05-09

    The history of the design and construction of the Argonne 500 MeV booster proton synchrotron from 1969 to 1982 is described. This accelerator has since been in steady use for the past 25 years to power the Argonne Intense Pulsed Neutron Source (IPNS).

  19. Accessing hospital packaged foods and beverages : the importance of a seated posture when eating

    OpenAIRE

    Bell, Alison; Tapsell, Linda; Walton, Karen; Yoxall, Alaster

    2017-01-01

    Background: Hospitalised and community dwelling older people (65 years and over), have difficulties opening food and beverage items such as cheese portions and tetra packs served in public hospitals. Previously, the role of hand strength on successful pack opening has been explored in a seated position. However, as many people in hospital eat in bed, this laboratory study examined the differences between participants opening a selection of products both in a hospital bed and a chair.\\ud Metho...

  20. Acupuncture Deqi Intensity and Propagated Sensation along Channels May, Respectively, Differ due to Different Body Positions of Subjects

    Directory of Open Access Journals (Sweden)

    Xiang-Zhu Chen

    2013-01-01

    Full Text Available Acupuncture as an essential component of complementary and alternative medicine is gradually recognized and accepted by the mainstream of contemporary medicine. For obtaining preferable clinical effectiveness, Deqi is commonly regarded as efficacy predictor and parameter which is necessary to be achieved. Influential factors for acupuncture efficacy, like Deqi sensation as well as propagated sensation along channels (PSCs, enjoyed a long history in acupuncture basic research. Concerning this study, taking into account different positions on acupuncture Deqi sensation and PSCs, we would like to attest whether different body positions for subjects during needling procedure yield differed acupuncture Deqi sensation, particularly in terms of intensity, and PSCs. Methods. We used self-controlled method and selected 30 healthy subjects to perform needle insertion at Futu point (ST32 bilaterally. Then they were instructed to record the value of intensity of acupuncture sensation and the length and width of PSCs after removing the needle. Results. In regard to intensity of Deqi, kneeling seat position is stronger than supine position, accounting for 90% of the total number of subjects. In length of PSCs, kneeling seat position is greater than supine position, accounting for 56.7%. In width of PSCs, kneeling seat position is greater than supine position, accounting for 66.7%. Conclusion. Our findings show that needle inserting at Futu point (ST32 in kneeling seat position achieve better needle sensation and provide reference for clinical.

  1. Automatic delamination defect detection in radiographic sequence of rocket boosters

    International Nuclear Information System (INIS)

    Rebuffel, V.; Pires, S.; Caplier, A.; Lamarque, P.

    2003-01-01

    Solid rocket motors are routinely examined in real-time X-ray radioscopic mode. The large and cylindrical boosters are rotating between a high energy source and a two dimensional detector. The purpose of this control is to detect possible defects all through the sample. In the tangential configuration, the part of the object that intersects the X-rays beam is the peripheral one, allowing to detect the delamination defect between the propellant and the external metal envelope. But the defect detectability is very poor due to the strong attenuation of the X-rays through the motors. During the rotation of the booster, the system acquires a sequence of radiographs where the defects are visible over several successive instants. We have previously developed a real-time tomo-synthesis system, processing the radiographs on line, and based on a tomo-synthesis reconstruction algorithm in order to improve the signal-to-noise ratio. This system is installed at the industrial site of Kourou, and is currently used by the operators in charge of the visual inspection of the boosters. In this paper, we present a method that processes the digital images obtained by the system in the purpose of automatically extracting the delamination defects. Due to the size and the poor contrast of the defects, a single image is not sufficient to perform this detection. A spatio-temporal aspect is required for the algorithm to be robust and efficient. In a first step, the proposed method computes the apparent local displacement between the current radiograph and a reference one. This reference image is acquired at the beginning of the rotation, with few noise, and is supposed to be defect free. The apparent displacement is due to the non-perfect rotation positioning. It may be uniform or not, depending on the deformation of the insulation liner of the metallic wall. The images are then registered and compared. On the resulting difference image we apply a smoothed threshold to obtain an

  2. 76 FR 23793 - Extension of Application Period for Seats for the Stellwagen Bank National Marine Sanctuary...

    Science.gov (United States)

    2011-04-28

    ... Period for Seats for the Stellwagen Bank National Marine Sanctuary Advisory Council AGENCY: Office of National Marine Sanctuaries (ONMS), National Ocean Service (NOS), National Oceanic and Atmospheric... seats on the Stellwagen Bank National Marine Sanctuary Advisory Council: (1) Research Member seat and (2...

  3. Impact of Active Climate Control Seats on Energy Use, Fuel Use, and CO2 Emissions

    Energy Technology Data Exchange (ETDEWEB)

    Kreutzer, Cory J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Rugh, John P [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Titov, Eugene V [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Kekelia, Bidzina [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-11-28

    A project was developed through collaboration between Gentherm and NREL to determine the impact of climate control seats for light-duty vehicles in the United States. The project used a combination of experimentation and analysis, with experimental results providing critical input to the analysis process. First, outdoor stationary vehicle testing was performed at NREL's facility in Golden, CO using multiple occupants. Two pre-production Ford Focus electric vehicles were used for testing; one containing a standard inactive seat and the second vehicle containing a Gentherm climate control seat. Multiple maximum cool-down and steady-state cooling tests were performed in late summer conditions. The two vehicles were used to determine the increase in cabin temperature when using the climate control seat in comparison to the baseline vehicle cabin temperature with a standard seat at the equivalent occupant whole-body sensation. The experiments estimated that on average, the climate control seats allowed for a 2.61 degrees Celsius increase in vehicle cabin temperature at equivalent occupant body sensation compared to the baseline vehicle. The increased cabin air temperature along with their measured energy usage were then used as inputs to the national analysis process. The national analysis process was constructed from full vehicle cabin, HVAC, and propulsion models previously developed by NREL. In addition, three representative vehicle platforms, vehicle usage patterns, and vehicle registration weighted environmental data were integrated into the analysis process. Both the baseline vehicle and the vehicle with climate control seats were simulated, using the experimentally determined cabin temperature offset of 2.61degrees Celsius and added seat energy as inputs to the climate control seat vehicle model. The U.S. composite annual fuel use savings for the climate control seats over the baseline A/C system was determined to be 5.1 gallons of gasoline per year per

  4. Improving the performance of booster heat pumps using zeotropic mixtures

    DEFF Research Database (Denmark)

    Zühlsdorf, B.; Meesenburg, W.; Ommen, T. S.

    2018-01-01

    Abstract This study demonstrated an increase in the thermodynamic performance of a booster heat pump, which was achieved by choosing the working fluid among pure and mixed fluids. The booster heat pump was integrated in an ultra-low-temperature district heating network with a forward temperature...... of 40 °C to produce domestic hot water, by heating part of the forward stream to 60 °C, while cooling the remaining part to the return temperature of 25 °C. The screening of working fluids considered 18 pure working fluids and all possible binary mixtures of these fluids. The most promising solutions...... heat supply system while being economically competitive to pure fluids....

  5. Assessment of the vibration on the foam legged and sheet metal-legged passenger seat

    Directory of Open Access Journals (Sweden)

    L. Dahil

    2015-10-01

    Full Text Available In this study, it was aim ed to decrease the vibration reaching to passenger from the legs of vehicle seats. In order to determine the levels of vibrations reaching at passengers, a test pad placed under the passenger seat was used, and HVM100 device was used for digitizing the information obtained. By transferring the vibration data to system by using HVM100 device, the acceleration graphics were prepared with Blaze software. As a result, it was determined that the acceleration values of seat legs made of foam material were lower than that of seat legs made of 2 mm thick sheet metal, so they damped the vibration better.

  6. Precise positioning of patients for radiation therapy

    International Nuclear Information System (INIS)

    Verhey, L.J.; Goitein, M.; McNulty, P.; Munzenrider, J.E.; Suit, H.D.

    1982-01-01

    A number of immobilization schemes which permit precise daily positioning of patients for radiation therapy are discussed. Pretreatment and post-treatment radiographs have been taken with the patient in the treatment position and analyzed to determine the amount of intratreatment movement. Studies of patients in the supine, seated and decubitus positions indicate mean movements of less than 1 mm with a standard deviation of less than 1 mm. Patients immobilized in the seated position with a bite block and a mask have a mean movement of about 0.5 mm +/- 0.3 mm (s.d.), and patients immobilized in the supine position with their necks hyperextended for submental therapy evidence a mean movement of about 1.4 mm +/- 0.9 mm (s.d.). With the exception of those used for the decubitus position, the immobilization devices are simply fabricated out of thermoplastic casting materials readily available from orthopedic supply houses. A study of day-to-day reproducibility of patient position using laser alignment and pretreatment radiographs for final verification of position indicates that the initial laser alignment can be used to position a patient within 2.2 mm +/- 1.4 mm (s.d.) of the intended position. These results indicate that rigid immobilization devices can improve the precision of radiotherapy, which would be advantageous with respect to both tumor and normal tissue coverage in certain situations

  7. A FET based kicker for a charge booster for the TRIUMF ISAC project

    International Nuclear Information System (INIS)

    Barnes, M.J.; Wait, G.D.

    2001-07-01

    A charge booster unit is required as part of an upgrade to the ISAC facility at TRIUMF. ISAC is an isotope separator coupled to an accelerator. ISAC is presently capable of accelerating only isotopes with atomic mass up to 30. The charge booster will allow ISAC to accelerate all the masses in the periodic table. A fast kicker system has been built to study the characteristics of an existing charge booster, designed by ISN in Grenoble, to assess the suitability of using this charge booster at TRIUMF. This fast kicker will subsequently be used in the TRIUMF ISAC facility for time of flight separation of the chosen charge and to recycle the higher and lower charges back to the charge booster. This will increase the efficiency from 10% to 60%. The kicker system includes a pair of deflector plates. One plate is charged up to -3.5 kV by a PET based modulator, while the other plate is held at ground potential. The modulator consists of two stacks of FETs operating in push pull with variable output voltage, pulse width, and repetition rate from virtually DC to 52 kHz. The measured high voltage output pulse rise and fall times are 63 ns and the minimum pulse width is 350 ns. The maximum pulse width is dependent upon the repetition rate. The large dynamic range for the repetition rate and pulse width required a novel circuit design and control technique, which also resulted in an energy efficient kicker system. This paper describes the design of the kicker system and shows the results of measurements. (author)

  8. Frequency control of RF booster cavity in TRIUMF

    International Nuclear Information System (INIS)

    Fong, K.; Laverty, M.

    1993-01-01

    A booster is used in the TRIUMF cyclotron to increase the energy gain per turn for beam orbits corresponding to energies greater than 370 MeV. It operates at 92.24 MHz, the 4 th harmonic of the cyclotron main rf, and at a nominal voltage of 150 kV. Excitation is provided by a 90 kW rf system that is phase locked to the main rf. When the main rf is interrupted due to sparking or other causes, a controller built into the low frequency source of the booster rf system disables the phase-locked loop, and reconfigures the source as a temperature stabilized oscillator operating at the last locked frequency. When the cyclotron rf is restored it usually will be at different frequency. The oscillator tunes automatically to this new frequency. The acquisition time is extended by the controller to match the response time of the mechanical tuner in the cavity

  9. A joint econometric analysis of seat belt use and crash-related injury severity.

    Science.gov (United States)

    Eluru, Naveen; Bhat, Chandra R

    2007-09-01

    This paper formulates a comprehensive econometric structure that recognizes two important issues in crash-related injury severity analysis. First, the impact of a factor on injury severity may be moderated by various observed and unobserved variables specific to an individual or to a crash. Second, seat belt use is likely to be endogenous to injury severity. That is, it is possible that intrinsically unsafe drivers do not wear seat belts and are the ones likely to be involved in high injury severity crashes because of their unsafe driving habits. The preceding issues are considered in the current research effort through the development of a comprehensive model of seat belt use and injury severity that takes the form of a joint correlated random coefficients binary-ordered response system. To our knowledge, this is the first instance of such a model formulation and application not only in the safety analysis literature, but in the econometrics literature in general. The empirical analysis is based on the 2003 General Estimates System (GES) data base. Several types of variables are considered to explain seat belt use and injury severity levels, including driver characteristics, vehicle characteristics, roadway design attributes, environmental factors, and crash characteristics. The results, in addition to confirming the effects of various explanatory variables, also highlight the importance of (a) considering the moderating effects of unobserved individual/crash-related factors on the determinants of injury severity and (b) seat belt use endogeneity. From a policy standpoint, the results suggest that seat belt non-users, when apprehended in the act, should perhaps be subjected to both a fine (to increase the chances that they wear seat belts) as well as mandatory enrollment in a defensive driving course (to attempt to change their aggressive driving behaviors).

  10. Valve seat pores sealed with thermosetting monomer

    Science.gov (United States)

    Olmore, A. B.

    1966-01-01

    Hard anodic coating provides a smooth wear resistant value seating surface on a cast aluminum alloy valve body. Vacuum impregnation with a thermosetting monomer, diallyl phthalate, seals the pores on the coating to prevent galvanic corrosion.

  11. Evaluating the impact of child safety seat check-up events on parental knowledge.

    Science.gov (United States)

    Herring, Ashley B; Jones, Ches; Nunez, Casandra

    2002-12-01

    Riding unrestrained is the greatest risk factor for death and injury among children in motor vehicles. Restraining a child can reduce the risk of death for that child by up to 71%. However, despite increased awareness, child safety seat usage rates are still disturbingly low. The purpose of this study was to evaluate the impact that child safety seat check-up events have on parental knowledge on child safety seats and installation. The subjects for this study were 101 parents/caregivers who attended child safety seat check-up events in northwest Arkansas from May 2000 through June 2001. A 20-item survey was conducted via the telephone. Results showed that the check-up events in northwest Arkansas have had an impact on self-efficacy. The participants of the events were primarily Caucasian and females in the 30-34 age group. Nine of 10 subjects scored in the high knowledge category. Conclusions are that check-up events do have an impact on parental knowledge and are accepted by the target group. Additionally, participants believed that car seats are of great importance and do protect their children in the event of a crash.

  12. 75 FR 63766 - Digital Low Power Television, Television Translator, and Television Booster Stations and Digital...

    Science.gov (United States)

    2010-10-18

    ...] Digital Low Power Television, Television Translator, and Television Booster Stations and Digital Class A... TV, TV Translator or TV Booster Station, FCC Form 346; 47 CFR 74.793(d); LPTV Out-of-Core Digital... collection requirements: 47 CFR 74.793(d) proposes that certain digital low power and TV translator stations...

  13. Rear seat safety: Variation in protection by occupant, crash and vehicle characteristics.

    Science.gov (United States)

    Durbin, Dennis R; Jermakian, Jessica S; Kallan, Michael J; McCartt, Anne T; Arbogast, Kristy B; Zonfrillo, Mark R; Myers, Rachel K

    2015-07-01

    Current information on the safety of rear row occupants of all ages is needed to inform further advances in rear seat restraint system design and testing. The objectives of this study were to describe characteristics of occupants in the front and rear rows of model year 2000 and newer vehicles involved in crashes and determine the risk of serious injury for restrained crash-involved rear row occupants and the relative risk of fatal injury for restrained rear row vs. front passenger seat occupants by age group, impact direction, and vehicle model year. Data from the National Automotive Sampling System Crashworthiness Data System (NASS-CDS) and Fatality Analysis Reporting System (FARS) were queried for all crashes during 2007-2012 involving model year 2000 and newer passenger vehicles. Data from NASS-CDS were used to describe characteristics of occupants in the front and rear rows and to determine the risk of serious injury (AIS 3+) for restrained rear row occupants by occupant age, vehicle model year, and impact direction. Using a combined data set containing data on fatalities from FARS and estimates of the total population of occupants in crashes from NASS-CDS, logistic regression modeling was used to compute the relative risk (RR) of death for restrained occupants in the rear vs. front passenger seat by occupant age, impact direction, and vehicle model year. Among all vehicle occupants in tow-away crashes during 2007-2012, 12.3% were in the rear row where the overall risk of serious injury was 1.3%. Among restrained rear row occupants, the risk of serious injury varied by occupant age, with older adults at the highest risk of serious injury (2.9%); by impact direction, with rollover crashes associated with the highest risk (1.5%); and by vehicle model year, with model year 2007 and newer vehicles having the lowest risk of serious injury (0.3%). Relative risk of death was lower for restrained children up to age 8 in the rear compared with passengers in the right

  14. SNS RING STUDY AT THE AGS BOOSTER.

    Energy Technology Data Exchange (ETDEWEB)

    ZHANG, S.Y.; AHRENS, L.; BEEBE-WANG, J.; BLASKIEWICZ, M.; FEDOTOV, A.; GARDNER, C.; LEE, Y.Y.; LUCCIO, A.; MALITSKY, N.; ROSER, T.; WENG, W.T.; WEI, J.; ZENO, K.; REECE, K.; WANG, J.G.

    2000-06-30

    During the g-2 run at the BNL AGS in early 2000, a 200 MeV storage-ring-like magnetic cycle has been set-up and tuned at the Booster in preparing for the Spallation Neutron Source (SNS) accumulator ring study. In this article, we report the progress of the machine set-up, tuning, some preliminary studies, and the future plan.

  15. Relativistic heavy ions from the BNL [Brookhaven National Laboratory] booster medical research and technological applications

    International Nuclear Information System (INIS)

    Thieberger, P.

    1990-05-01

    The BNL Booster, now nearing completion, was designed to inject protons and heavy ions into the Alternating Gradient Synchrotron (AGS) for further acceleration. In the future, ion beams from the AGS will in turn be further accelerated in the Relativistic Heavy Ion Collider (RHIC). Given the wide range of ion masses, energies and beam intensities the Booster will generate, other important applications should be considered. Dedicated use of the Booster for such applications may be possible during limited periods. However shared use would be preferable from the points of view of availability, affordability and efficiency. While heavy ions of a given isotope are injected into the AGS, the same or other ion species from the Booster could be simultaneously delivered to a new irradiation area for treatment of patients, testing of electronic devices or other applications and research. To generate two different beam species, ion sources on both Tandem accelerators would be used; one for AGS injection and the other one for a time-sharing application. Since the beam transport from the Tandems to the Booster can not be rapidly adjusted, it will be necessary to select beams of identical magnetic rigidity. The present study was performed to determine to what extent this compatibility requirement imposes limitations on the available ion species, energies and/or intensities

  16. Superconducting linac booster

    International Nuclear Information System (INIS)

    Srinivasan, B.; Betigeri, M.G.; Pandey, M.K.; Pillay, R.G.; Kurup, M.B.

    1997-01-01

    The report on superconducting LINAC booster, which is a joint project of Bhabha Atomic Research Centre (BARC) and Tata Institute of Fundamental Research (TIFR), brings out the work accomplished so far towards the development of the technology of superconducting LINAC to boost the energy of ions from the 14UD Pelletron. The LINAC is modular in construction with each module comprising of a helium cryostat housing four lead-plated quarter wave resonators. The resonators are superconducting for temperatures below 7.19K. An energy boost of 2 MeV/q per module is expected to be achieved. The first module and the post-tandem superbuncher have been fabricated and tested on the LINAC beam line. This report gives a summary of the technological achievements and also brings out the difficulties encountered during the R and D phase. (author)

  17. 76 FR 44821 - Digital Low Power Television, Television Translator, and Television Booster Stations and To Amend...

    Science.gov (United States)

    2011-07-27

    ...] Digital Low Power Television, Television Translator, and Television Booster Stations and To Amend Rules... Digital Low Power Television, Television Translator, and Television Booster Stations and to Amend Rules... translator facilities in the 700 MHz band. These provisions provide procedures for a primary wireless...

  18. 76 FR 72849 - Digital Low Power Television, Television Translator, and Television Booster Stations and To Amend...

    Science.gov (United States)

    2011-11-28

    ...] Digital Low Power Television, Television Translator, and Television Booster Stations and To Amend Rules... for Digital Low Power Television, Television Translator, and Television Booster Stations and to Amend... television, TV translator, and Class A television station DTV licensees''). The Commission has also revised...

  19. Pattern of seat belt use and its associated factors among taxi drivers ...

    African Journals Online (AJOL)

    Objective: Road traffic injuries constitute a major public health concern that demands effective interventions. Use of car seat belts is recommended as an effective intervention to reduce serious and fatal road traffic injuries. The study intended to investigate the pattern of seat belt use and its correlates among taxi drivers in ...

  20. PS Booster Orbit Correction

    CERN Document Server

    Chanel, M; Rumolo, G; Tomás, R; CERN. Geneva. AB Department

    2008-01-01

    At the end of the 2007 run, orbit measurements were carried out in the 4 rings of the PS Booster (PSB) for different working points and beam energies. The aim of these measurements was to provide the necessary input data for a PSB realignment campaign during the 2007/2008 shutdown. Currently, only very few corrector magnets can be operated reliably in the PSB; therefore the orbit correction has to be achieved by displacing (horizontally and vertically) and/or tilting some of the defocusing quadrupoles (QDs). In this report we first describe the orbit measurements, followed by a detailed explanation of the orbit correction strategy. Results and conclusions are presented in the last section.

  1. Performance of a correlator filter in betatron tune measurements and damping on the NSLS booster

    International Nuclear Information System (INIS)

    Galayda, J.

    1985-01-01

    A ''compensated correlator filter'', described by Kramer, et al. has been used for measurement and damping of betatron oscillations in the NSLS booster. The filter consists of a zero-degree power splitter, a 180-degree splitter, a length of 7/8'' air dielectric coaxial cable, and a short length of RG-58 cable. Connected to a beam position monitor, the output of the filter is proportional to the difference in transverse position of each bunch on subsequent turns. The useful bandwidth of the filter for damping rigid bunch oscillations extends from 10 MHz to 250 MHz, in contrast with the gigahertz bandwidth requirements for stochastic cooling, for which the filter was originally proposed. Attenuation of all rotation harmonics in this bandwidth is 40 to 60 dB

  2. Charge exchange studies with Gold ions at the Brookhaven Booster and AGS

    International Nuclear Information System (INIS)

    Ahrens, L.A.; Hseuh, H.C.; Roser, T.

    1994-01-01

    Efficient acceleration of Gold ions to ll GeV/nucleon places strong constraints on the vacuum and also on the choice of thickness and material of the necessary stripping foils. Results of a number of detailed experimental studies performed with the Gold beam at the Brookhaven Booster and AGS to determine the relevant electron stripping and pick-up probabilities are presented. Of particular interest is the lifetime of the relatively low energy, partially stripped Gold beam in the Booster and the stripping efficiency to Helium-like AU +77 for injection into the AGS

  3. Superconducting LINAC booster for the pelletron accelerator at Bombay

    International Nuclear Information System (INIS)

    Pillay, R.G.; Kurup, M.B.; Jain, A.K.; Biswas, D.; Kori, S.A.; Srinivasan, B.

    1989-01-01

    A superconducting heavy ion linear accelerator being constructed as a booster for the 14 UD pelletron installed recently at Bombay. The work involved in this project and the progress made so far are reviewed. (author). 15 refs., 8 figs

  4. Experimental Investigation of a Temperature-Controlled Car Seat Powered by an Exhaust Thermoelectric Generator

    Science.gov (United States)

    Du, H.; Wang, Y. P.; Yuan, X. H.; Deng, Y. D.; Su, C. Q.

    2016-03-01

    To improve the riding comfort and rational utilization of the electrical energy captured by an automotive thermoelectric generator (ATEG), a temperature-controlled car seat was constructed to adjust the temperature of the car seat surface. Powered by the ATEG and the battery, the seat-embedded air conditioner can improve the riding comfort using a thermoelectric device to adjust the surface temperature of the seat, with an air duct to regulate the cold side and hot side of the thermoelectric device. The performance of the thermoelectric cooler (TEC) and theoretical analysis on the optimum state of the TEC device are put forward. To verify the rationality of the air duct design and to ensure sufficient air supply, the velocity field of the air duct system was obtained by means of the finite element method. To validate the reliability of the numerical simulation, the air velocity around the thermoelectric device was measured by a wind speed transmitter. The performance of the temperature-controlled car seat has been validated and is in good agreement with bench tests and real vehicle tests.

  5. Pressure measurements in the AGS Booster ultra-high vacuum system

    International Nuclear Information System (INIS)

    Gabusi, J.; Geller, J.; Hseuh, H.C.; Mapes, M.; Stattel, P.

    1992-01-01

    An average pressure of mid 10 -11 Torr has been achieved and maintained in the AGS Booster ring vacuum system during its first year of operation. This ultra-high vacuum system is monitored through remote controlled Bayard-Alpert Gauges (BAGs). The characteristics of the pressure measurements with BAGs over the long cable lengths (up to 200 m) and under various accelerator operating conditions will be described. Two types of noise in the pressure readouts have been identified; the electromagnetic interference (EMI) associated with the acceleration cycles of the Booster and the environment noise associated with the temperature of the collector cables. The magnitude of the noise pickup depends on the routing of the collector cables and reaches the equivalent pressure of low 10 -9 Torr

  6. Response of booster dose of cuban recombinant hepatitis-B vaccine in nonresponder and hyporesponder children

    International Nuclear Information System (INIS)

    Dahifar, H.; Mousavi, F.; Ghorbani, A.

    2007-01-01

    Acute hepatitis B infection can debilitate a patient for weeks and occasionally has a fatal outcome, while chronic infection is a major threat to the individual. To assess response of nonresponder and hyporesponder children to booster dose of Cuban recombinant hepatitis B vaccine. An interventional, descriptive study has been conducted on children who had been immunized with Cuban recombinant Hepatitis B vaccine and their antibody titers were <10mIU/ml (nonresponder) and 10-100mIU/ml (hyporesponder) administered booster dose of the same vaccine in their Deltoid muscles. The response of 141 children with the mean age of 1.9 years to booster dose of vaccine were 94.3% and 100% vaccines with the first and second booster dose of vaccination respectively. The anti-HBs titer in nonresponders and hyporesponders were 468+-346 and 783+-346mIU/ml respectively with significant differences between two groups (P=0.001). This study demonstrate moderately increase antibody production in the majority of vaccines with single supplementary vaccine. (author)

  7. Beam aperture and emittance growth in the AGS-Booster

    International Nuclear Information System (INIS)

    Parsa, Z.

    1987-01-01

    The authors have developed analytical tools for calculating the variation of particle action, smear and emittance growth due to nonlinear elements in accelerators (with second order perturbation theory in two dimensions). The authors' results for the AGS-Booster is presented

  8. Simulation of the capture process in the Fermilab Booster

    International Nuclear Information System (INIS)

    Stahl, S.; Ankenbrandt, C.

    1987-01-01

    A progress report on efforts to understand and improve adiabatic capture in the Fermilab Booster by experiment and simulation is presented. In particular, a new Rf voltage program for capture which ameliorates transverse space-charge effects is described and simulated

  9. OPTIMAL SCHEDULING OF BOOSTER DISINFECTION IN WATER DISTRIBUTION SYSTEMS

    Science.gov (United States)

    Booster disinfection is the addition of disinfectant at locations distributed throughout a water distribution system. Such a strategy can reduce the mass of disinfectant required to maintain a detectable residual at points of consumption in the distribution system, which may lea...

  10. Simulation of proton RF capture in the AGS Booster

    International Nuclear Information System (INIS)

    Khiari, F.Z.; Luccio, A.U.; Weng, W.T.

    1988-01-01

    RF capture of the proton beam in the AGS Booster has been simulated with the longitudinal phase-space tracking code ESME. Results show that a capture in excess of 95% can be achieved with multiturn injection of a chopped beam

  11. Synchronization of the Zero Gradient Synchrotron (ZGS) and the fast-cycling booster II injector

    International Nuclear Information System (INIS)

    Rauchas, A.V.

    1977-01-01

    The planned method of booster injection into the ZGS requires the stacking of two booster beam bunches into the radial betatron phase space of the ZGS and necessitates precise synchronization of the two accelerators during the injection period. The requirement of maintaining independent radio-frequency (rf) steering control does not allow the frequencies of both accelerators to be locked. A synchronizer was developed which detects a coincidence zero crossing of the two rf's, anticipates the next coincidence, and at that time, generates trigger pulses for the booster extraction and ZGS injection systems. It also maintains control of the sequence in which the total phase space area of the ZGS is loaded. Synchronizer accuracy is obtained by using high speed digital logic circuits. Design considerations and system operation are discussed

  12. Pengaruh Tandem Booster TNT Terhadap Kecepatan Detonasi Campuran Bahan Peledak Tepung Kalium Klorat, Sulfur Dan Aluminium Sebagai Bahan Peldak High Explosive

    OpenAIRE

    Tarigan, Tarsim

    2010-01-01

    There are a research on velocity of detonation explosives from Improvised Bomb with potassium chlorate, sulfur and aluminum with a composition of 65:20:15% (weight / weight), 70 mesh, galvanized pipes and containers with some blasting mechanism, starts with an explosion that ignite by a improvise detonator, factory detonator without a booster, factory detonator with a tandem booster TNT, and TNT booster modifications by adding a layer of Pb plate and make a cavity between the main booster ch...

  13. Effect of a Dynamic Seating Surface on Postural Control and Function in Children with Cerebral Palsy

    DEFF Research Database (Denmark)

    Meyer, Erna Rosenlund; Trew, Lisa

    Purpose: The purpose was to investigate if a seating system involving a dynamic material covering the seat back and base improves postural control, alignment and function in children with cerebral palsy and to investigate consequences of adapting The Seated Postural Control Measure to a target...... group with multifunctional disabilities. Relevance: Developing sitting systems for disabled persons is of great importance to avoid sitting problems, to increase the level of functioning and postural control which will have an impact on their daily living and activities. This project takes its starting...... Ethical Committee. Outcome measures were Seated Postural Control Measure (SPCM), which was modified to meet the children’s needs, was used to measure alignment and function. Force Sensitive Applications (FSA) on the seat surfaces was used to measure postural movements and interface pressure. All tests...

  14. LMFBR with booster pump in pumping loop

    International Nuclear Information System (INIS)

    Rubinstein, H.J.

    1975-01-01

    A loop coolant circulation system is described for a liquid metal fast breeder reactor (LMFBR) utilizing a low head, high specific speed booster pump in the hot leg of the coolant loop with the main pump located in the cold leg of the loop, thereby providing the advantages of operating the main pump in the hot leg with the reliability of cold leg pump operation

  15. Control of Fermilab Booster tunes

    International Nuclear Information System (INIS)

    Johnson, R.P; Meisner, K.; Sandberg, B.

    1977-01-01

    Control of the radial and vertical tunes of the booster is implemented using ramped correction quadrupoles. Minor modifications to the power supply cards for the 48 (previously) dc correction quadrupoles allow ''the tunes'' to be continuously programmed or held constant throughout the 33 ms acceleration cycle. This capability is in addition to the usual use of these quadrupoles to be independently varied to correct for harmonic distortions in the lattice. An automatic computer program measures and displays the tunes vs. time in the cycle to monitor performance and to allow the ramps to be adjusted by the machine operator

  16. Commercial herbal medicines used as African traditional medicines: Ngoma Herbal Tonic Immune Booster interferes with a rapid urine drug screening test.

    Science.gov (United States)

    Mothibe, M E; Osuch, E; Kahler-Venter, C P

    2017-08-25

    The prevalent use of African traditional medicine by the general public has been reported. With commercialisation and marketing, some of the herbal medicines (HMs) used are readily available over the counter, most of them promoted as immune boosters. These commercial HMs have not been taken through clinical trials and other tests that would validate their composition and safety, and other properties such as their effect on laboratory diagnostic tests. To investigate the cross-reactivity of selected HMs with commonly tested drugs of abuse (DoA) using a qualitative rapid urinalysis assay. The six HMs selected were bought from local pharmacies. A rapid urinalysis screening test was performed with the Instant View Multi-Drug of Abuse Test kit from Labstix Diagnostics. Drug-free urine (DFU) was pooled from samples donated by healthy volunteers. Urine samples that had tested positive for DoA were obtained from a pharmacology laboratory. Aliquots of the urine samples were spiked with the HMs in neat and diluted form, and tested at various time intervals. The results for the DFU samples spiked with the HMs remained negative. There were no significant changes in pH or specific gravity of the samples. The results of samples that had tested positive for tetrahydrocannabinol (THC) were not altered by five of the HMs when spiked at 40% v/v. The HM Ngoma Herbal Tonic Immune Booster caused false-negative results for the THC test. An important finding is that the herbal mixture Ngoma Herbal Tonic Immune Booster caused false-negative results for the cannabinoid screening test. It adds to the list of substances that may be potential adulterants of urine for screening tests.

  17. One-year post-primary antibody persistence and booster immune ...

    African Journals Online (AJOL)

    One-year post-primary antibody persistence and booster immune response to a DTaP-IPV//PRP~T vaccine (Pentaxim) given at 18 - 19 months of age in South African children primed at 6, 10 and 14 weeks of age with the same vaccine.

  18. Assessing ergonomic risks of software: Development of the SEAT.

    Science.gov (United States)

    Peres, S Camille; Mehta, Ranjana K; Ritchey, Paul

    2017-03-01

    Software utilizing interaction designs that require extensive dragging or clicking of icons may increase users' risks for upper extremity cumulative trauma disorders. The purpose of this research is to develop a Self-report Ergonomic Assessment Tool (SEAT) for assessing the risks of software interaction designs and facilitate mitigation of those risks. A 28-item self-report measure was developed by combining and modifying items from existing industrial ergonomic tools. Data were collected from 166 participants after they completed four different tasks that varied by method of input (touch or keyboard and mouse) and type of task (selecting or typing). Principal component analysis found distinct factors associated with stress (i.e., demands) and strain (i.e., response). Repeated measures analyses of variance showed that participants could discriminate the different strain induced by the input methods and tasks. However, participants' ability to discriminate between the stressors associated with that strain was mixed. Further validation of the SEAT is necessary but these results indicate that the SEAT may be a viable method of assessing ergonomics risks presented by software design. Copyright © 2016 Elsevier Ltd. All rights reserved.

  19. Fabrication of a prototype dipole for the SSC Low Energy Booster

    International Nuclear Information System (INIS)

    Spencer, C.M.

    1993-12-01

    The Low Energy Booster of the Superconducting Super Collider (SSC) will be a synchrotron containing 96 dipoles operating between 0.13 T and 1.35 T at 10 Hz. Each dipole's 1.865 m-long core is made from ∼2900 steel laminations (lams), each 52 x 66 cm and 0.635 mm thick. A need to minimize power supply costs and stringent field specifications led to a straight core with very tight mechanical tolerances of the order of 0.05 mm. To satisfy these tolerances, we decided to stack the core in a vertical position; i.e., with the laminations laid horizontally. We designed and built an unusual vertical stacking fixture that pivots into a horizontal position after all the laminations have been stacked and compressed and four support angles welded onto the laminations. The stacking fixture, our experience using it, and conclusions as to the merits of stacking such a long core vertically will be described. The methods of insulating and potting the pancake coils and their installation into the unsplittable core is also described

  20. 47 CFR 90.219 - Use of signal boosters.

    Science.gov (United States)

    2010-10-01

    ... to operate radio systems in the frequency bands above 150 MHz may employ signal boosters at fixed... fill in only weak signal areas and cannot extend the system's normal signal coverage area. (b) Class A... effective radiated power (ERP) of the unit to a maximum of 5 watts under all conditions. Class B broadband...

  1. 76 FR 64074 - Request for Applications for Vacant Seats on the Flower Garden Banks National Marine Sanctuary...

    Science.gov (United States)

    2011-10-17

    ... for Vacant Seats on the Flower Garden Banks National Marine Sanctuary Advisory Council AGENCY: Office... ONMS is seeking applications for the following six vacant seats on the Flower Garden Banks National... experience in relation to the seat for which they are applying; community and professional affiliations...

  2. Attitudes towards child restrains and seat belts usage in the learned population of Karachi, Pakistan.

    Science.gov (United States)

    Siddiqui, Emaduddin; Ejaz, Kiran; Waheed, Shahan; Kazi, Ghazala Irfan; Khursheed, Munawar

    2014-01-01

    Motor vehicles crashes (MVCs) are the leading cause of injury related morbidity and mortality in developed countries. Recent evidence proves that properly used child seat belts can dramatically reduce the risk of severe and life-threatening injury from MVCs. There are rarities of thought and inspiration regarding the use of child seat belts in our society and region, therefore we lack of data regarding factors and paucity of usage of child seat belts in motor vehicles. This study aimed to assess the knowledge and attitudes of child seat belt usage among the educated population in Karachi, Pakistan. Altogether 304 employees were investigated. They were employees of Aga Khan University who were using their cars and having children younger than 10 years old. A cross sectional observational study was designed, and a 36-item questionnaire in English was used to collect data on participants' demographic details, designation, educational level, economic status, validity of driving license, number of children and cars, availability of adult seat belts and child seat belts along with their functionality, awareness, knowledge and attitude toward its use, and reason of not using these devices. SPSS version 20 for Windows was used to analyze the data and the Chi-square test was used. Totally 290 participants were recruited with a response rate of 72% (212). Of 212 participants, 126 (59%) were male. 154 (72.6%) participants had valid driver licenses, and 154 (72.6%) had adult seat belts in their vehicles. Only 32 (15%) reported regular use of adult seat belts. Although 168 (79.2%) participants had some knowledge about child restrains (CRs), only 65 (22%) had CRs in their cars. Eighty-two (38.7%) participants got the knowledge about CRs and seat belts from media. Mothers were more concerned about the use of CRs than fathers. Only 14 (6.6%) parents were found to use both adult and child seat belts all the time. Of the 157 parents who did not us use CRs, 42 considered unnecessary

  3. Charge exchange injection for Nuclotron and Nuclotron booster

    International Nuclear Information System (INIS)

    Dinev, D.; Mikhajlov, V.

    2000-01-01

    The acceleration of polarized beams is between the major items in the JINR LHE's heavy ion superconducting synchrotron Nuclotron research programme. One effective way to increase the intensities of polarized deuteron beams is the application of the charge exchange injection into the Nuclotron. The paper represents the results of a new analytical description of the heavy ion stripping injection based on the Boltzmann kinetic equation. Expressions for the ion density evolution in the transverse phase plane for the emittance growth due to the elastic scattering and to energy losses in the stripping foil and for the number of successfully stored particles have been derived. These results have been applied to the stripping injection of polarized deuterons into the Nuclotron as well as to the stripping injection of heavy ions into the now under consideration Nuclotron rapid cycling booster. It has been shown that an estimated 40-fold intensity gain could be achieved for the stripping injection of polarized D - into the Nuclotron and that an effective stripping injection of light and medium ions into the booster could be realized

  4. A cost benefit analysis of an enhanced seat belt enforcement program in South Africa.

    Science.gov (United States)

    Harris, G T; Olukoga, I A

    2005-04-01

    To examine whether a program to increase the wearing of seat belts in a South African urban area would be worthwhile in societal terms. A cost benefit analysis of a one year enhanced seat belt enforcement program in eThekwini (Durban) Municipality. Data were drawn from two main sources--a 1998 study of the cost of road crashes in South Africa and, given the absence of other data, a meta-analysis of the effectiveness of various types of interventions to reduce road crash casualties in the United States--and were analyzed using cost benefit analysis. A program designed to enforce greater wearing of seat belts, estimated to cost 2 million rand in one year, could be reasonably expected to increase seat belt usage rates by 16 percentage points and reduce fatalities and injuries by 9.5%. This would result in saved social costs of 13.6 million rand in the following year or a net present value of 11.6 million rand. There would also be favorable consequences for municipal finances. Investment in a program to increase seat belt wearing rates is highly profitable in societal terms.

  5. Simulation of the capture process in the Fermilab Booster

    International Nuclear Information System (INIS)

    Stahl, S.; Ankenbrandt, C.

    1987-09-01

    A progress report on efforts to understand and improve adiabatic capture in the Fermilab Booster by experiment and simulation is presented. In particular, a new RF voltage program for capture which ameliorates transverse space-charge effects is described and simulated. 7 refs., 4 figs

  6. Chromatic perturbation and resonance analysis for the AGS-Booster

    International Nuclear Information System (INIS)

    Parsa, Z.

    1987-01-01

    The authors investigated the nonlinear effects with the emphasis on nonlinear resonances. They present some of their findings, (e.g. the structure resonances; stop-bandwidths, etc.) for the AGS-Booster Lattice using program HARMON. Comparison with the results obtained from the algorithm ''NONLIN'' is presented

  7. Analysis of magnetic field measurement results for the AGS Booster magnets

    International Nuclear Information System (INIS)

    Bleser, E.; Thern, R.

    1991-01-01

    Magnetic field measurements have been made on nearly 200 conventional magnets that have been installed in the AGS Booster and its associated transfer lines. The measurements were intended to monitor the quality of the magnets being produced and to check the performance of each magnet before installation. The magnetic measurements effort led to certain improvements in the manufacturing process, which ten subsequently produced very good, very uniform magnets. The integrated dipole fields of the 36 booster dipoles are uniform to 1.5 parts in ten thousand. The magnetic measurements indicate that the quadrupoles were manufactured to an accuracy of 3 ten thousandths of an inch, which is better than we can physically measure. 3 refs., 2 figs., 4 tabs

  8. Factors associated with rear seating of children in motor vehicles: a study in two low-income, predominantly Hispanic communities.

    Science.gov (United States)

    Greenberg-Seth, Jennifer; Hemenway, David; Gallagher, Susan S; Lissy, Karen S; Ross, Julie B

    2004-07-01

    This study examined child seating patterns in two predominantly low-income, Hispanic communities in Massachusetts. The purpose was to determine the factors associated with child rear seating in the community as a whole and for a subset of Hispanic motorists. Five hundred and five vehicles carrying child passengers and no adult other than the driver were observed in parking lots of fast food restaurants and grocery stores. Four hundred and thirty-two vehicle drivers agreed to be interviewed. A child was defined as a passenger younger than age 12 as determined by appearance and height (head below the vehicle headrest when seated). Variables under study included driver gender, age, ethnicity, and educational attainment; driver shoulder belt use; driver perception of passenger-side airbag presence; and the number and ages of children in the car. Overall, 51% of vehicles were observed with all children seated in the rear. In a bivariate analysis, child rear seating was strongly associated with female drivers ( P = 0.01), younger drivers ( P = 0.02) driver shoulder belt use ( P safety behavior (e.g. seat belt use). Messages should be culturally appropriate and should emphasize driver seat belt use in conjunction with rear seating and the importance of rear seating regardless of the presence of a passenger-side airbag.

  9. 47 CFR 101.151 - Use of signal boosters.

    Science.gov (United States)

    2010-10-01

    ... authorized to operate multiple address systems in the 928-929/952-960 MHz and 932-932.5/941-941.5 MHz bands..., or portable station(s). The booster will fill in only weak signal areas and cannot extend the system... automatic gain control circuitry which will limit the total effective radiated power (ERP) of the unit to a...

  10. A Functional Analysis of DOD Implementation of Seat Management

    National Research Council Canada - National Science Library

    Rasmussen, David

    1999-01-01

    .... Seat management, also known as desktop outsourcing, involves the acquisition and management of all hardware and software, desktop and network management, operations management, support services...

  11. Machine for development impact tests in sports seats and similar

    International Nuclear Information System (INIS)

    Gonçalves, R M

    2015-01-01

    This paper describes the stages of development of a machine to perform impact tests in sport seats, seats for spectators and multiple seats. This includes reviews and recommendations for testing laboratories that have needs similar to the laboratory where unfolded this process.The machine was originally developed seeking to meet certain impact tests in accordance with the NBR15925 standards; 15878 and 16031. The process initially included the study of the rules and the election of the tests for which the machine could be developed and yet all reports and outcome of interaction with service providers and raw materials.For operating facility, it was necessary to set entirely the machine control, which included the concept of dialogue with operator, the design of the menu screens and the procedures for submission and registration of results. To ensure reliability in the process, the machine has been successfully calibrated according to the requirements of the Brazilian network of calibration.The criticism to this enterprise covers the technical and economic aspects involved and points out the main obstacles that were needed to overcome. (paper)

  12. Protection of children restrained in child safety seats in side impact crashes.

    Science.gov (United States)

    Arbogast, Kristy B; Locey, Caitlin M; Zonfrillo, Mark R; Maltese, Matthew R

    2010-10-01

    The performance of child restraint systems (CRS) in side impact motor vehicle crashes has been under study due to the injury and fatality burden of these events. Although previous research has quantified injury risk or described injured body regions, safety advances require an understanding of injury causation. Therefore, the objective was to delineate injury causation scenarios for CRS-restrained children in side impacts and document probable contact points in the vehicle interior. Two in-depth crash investigation databases, the Crash Injury Research and Engineering Network and the Partners for Child Passenger Safety Study, were queried for rear-seated, CRS-restrained children in side impact crashes who sustained Abbreviated Injury Scale 2+ injury. These cases were reviewed by a multidisciplinary team of physicians and engineers to describe injury patterns, injury causation, and vehicle components that contributed to the injuries. Forty-one occupants (average age, 2.6 years) met the inclusion criteria. Twenty-four were near side to the crash, 7 were far side, and 10 were center seated. The most common injuries were to the skull and brain with an increasing proportion of skull fracture as age increased. Head and spine injuries without evidence of head contact were rare but present. All thoracic injuries were lung contusions and no rib fractures occurred. Near-side head and face contacts points were along the rear vertical plane of the window and the horizontal plane of the window sill. Head and face contact points for center- and far-side occupants were along the edges of the front seat back and front seat head restraint. Head injuries are the target for injury prevention for children in CRS in side impact crashes. Most of these injuries are due to the contact; for near-side occupants, contact with the CRS structure and the door interior, for far- or center-seated occupants, contact with the front seat back. These data are useful in developing both educational and

  13. Reliability and responsiveness of the Self-Efficacy in Assessing, Training and Spotting wheelchair skills (SEATS) outcome measure.

    Science.gov (United States)

    Rushton, Paula W; Smith, Emma M; Miller, William C; Kirby, R Lee; Daoust, Geneviève

    2018-01-31

    The aim of this study was to evaluate the internal consistency, test-retest reliability and responsiveness of the Self-Efficacy in Assessing, Training and Spotting manual wheelchair skills (SEATS-M) and Self-Efficacy in Assessing, Training and Spotting power wheelchair skills (SEATS-P). A 2-week test-retest design was used with a convenience sample of occupational and physical therapists who worked at a provincial rehabilitation centre (inpatient and outpatient services). Sixteen participants completed the SEATS-M and 18 participants completed the SEATS-P. For the SEATS-M assessment, training, spotting and documentation sections, Cronbach's alpha coefficients ranged from 0.90 to 0.97, the 2-week intraclass correlation coefficients (ICC 1,1 ) ranged from 0.81 to 0.95, the standard error of measurements (SEM) ranged from 5.06 to 8.70 and the smallest real differences (SRD) ranged from 6.24 to 8.18. For the SEATS-P assessment, training, spotting and documentation sections, Cronbach's alpha coefficients ranged from 0.83 to 0.92, the ICCs ranged from 0.72 to 0.86, the SEMs ranged from 4.54 to 8.91 and the SRDs ranged from 5.90 to 8.27. There is preliminary evidence that both the SEATS-M and the SEATS-P have high internal consistency, good test-retest reliability and support for responsiveness. These tools can be used in evaluating clinician self-efficacy with assessing, training, spotting and documenting wheelchair skills included on the Wheelchair Skills Test. Implications for Rehabilitation There is preliminary evidence that the SEATS-M and SEATS-P are reliable and responsive outcome measures that can be used to evaluate the self-efficacy of clinicians to administer the Wheelchair Skills Program. Measurement of clinicians' self-efficacy in this area of practice may enable an enhanced understanding of the areas in which clinicians lack self-efficacy, thereby informing the development of improved knowledge translation interventions.

  14. Demonstration of the Trauma Nurses Talk Tough seat belt diversion program in North Carolina.

    Science.gov (United States)

    2014-03-01

    Trauma Nurses Talk Tough is a seat belt diversion program originally developed at the Legacy Emanuel Hospital in Portland, Oregon, in 1988. Attendance at the course is a condition for a one-time dismissal of a seat belt citation without fine or court...

  15. EVALUATING EXTREMELY LOW FREQUENCY MAGNETIC FIELDS IN THE REAR SEATS OF THE ELECTRIC VEHICLES.

    Science.gov (United States)

    Lin, Jun; Lu, Meng; Wu, Tong; Yang, Lei; Wu, Tongning

    2018-03-23

    In the electric vehicles (EVs), children can sit on a safety seat installed in the rear seats. Owing to their smaller physical dimensions, their heads, generally, are closer to the underfloor electrical systems where the magnetic field (MF) exposure is the greatest. In this study, the magnetic flux density (B) was measured in the rear seats of 10 different EVs, for different driving sessions. We used the measurement results from different heights corresponding to the locations of the heads of an adult and an infant to calculate the induced electric field (E-field) strength using anatomical human models. The results revealed that measured B fields in the rear seats were far below the reference levels by the International Commission on Non-Ionizing Radiation Protection. Although small children may be exposed to higher MF strength, induced E-field strengths were much lower than that of adults due to their particular physical dimensions.

  16. Flow Characteristics and Sizing of Annular Seat Valves for Digital Displacement Machines

    DEFF Research Database (Denmark)

    Nørgård, Christian; Bech, Michael Møller; Andersen, Torben O.

    2018-01-01

    operating range. To achieve high machine efficiency, the valve flow losses and the required electrical power needed for valve switching should be low. The annular valve plunger geometry, of a valve prototype developed for digital displacement machines, is parametrized by three parameters: stroke length......This paper investigates the steady-state flow characteristics and power losses of annular seat valves for digital displacement machines. Annular seat valves are promising candidates for active check-valves used in digital displacement fluid power machinery which excels in efficiency in a broad...... a valve prototype. Using the simulated maps to estimate the flow power losses and a simple generic model to estimate the electric power losses, both during digital displacement operation, optimal designs of annular seat valves, with respect to valve power losses, are derived under several different...

  17. Comparative Performance of Rear Facing Child Restraint Systems on the CMVSS 213 Bench and Vehicle Seats

    Science.gov (United States)

    Tylko, Suzanne; Locey, Caitlin M.; Garcia-Espana, J. Felipe; Arbogast, Kristy B.; Maltese, Matthew R.

    2013-01-01

    The purpose of this study was to compare the dynamic response of rear-facing child restraint systems (RFCRS) installed on the CMVSS 213 sled bench and a selection of vehicle seats. Thirty-six sled tests were conducted: three models of rear facing CRS with an anthropomorphic test device (ATD) representing a 12 month old child (CRABI) were affixed via lower anchors (LATCH), 3 point belt without CRS base, and 3 point belt with CRS base to one of three vehicle seats or the CMVSS 213 bench seat. All CRS were subjected to an identical sled acceleration pulse. Two types of matched pair analysis: “bench-to-vehicle” and “method of attachment” were conducted. Statistically significant differences were observed in the kinematic responses of the ATD and the CRS. This is the first study to quantify differences between the regulatory bench and vehicle seats on a system level and evaluate the influence of attachment method. Our results show that the difference in RFCRS forward excursion between 3-point belt with base and LATCH installations was between 1 and 7 percent on the bench and 22 to 76 percent on the vehicle seats. When evaluating the dynamic performance of RFCRS, the use of real vehicle seats from vehicles that commonly carry children may provide valuable insight. The findings would require further confirmation using a broader selection of RFCRS and vehicle seats, before generalizable conclusions can be drawn. PMID:24406967

  18. Hepatitis B virus vaccination booster does not provide additional protection in adolescents: a cross-sectional school-based study.

    Science.gov (United States)

    Chang, Yung-Chieh; Wang, Jen-Hung; Chen, Yu-Sheng; Lin, Jun-Song; Cheng, Ching-Feng; Chu, Chia-Hsiang

    2014-09-23

    Current consensus does not support the use of a universal booster of hepatitis B virus (HBV) vaccine because there is an anamnestic response in almost all children 15 years after universal infant HBV vaccination. We aimed to provide a booster strategy among adolescents as a result of their changes in lifestyle and sexual activity. This study comprised a series of cross-sectional serological surveys of HBV markers in four age groups between 2004 and 2012. The seropositivity rates of hepatitis B surface antigen (HBsAg) and its reciprocal antibody (anti-HBs) for each age group were collected. There were two parts to this study; age-specific HBV seroepidemiology and subgroup analysis, including effects of different vaccine types, booster response for immunogenicity at 15 years of age, and longitudinal follow-up to identify possible additional protection by HBV booster. Within the study period, data on serum anti-HBs and HBsAg in a total of 6950 students from four age groups were collected. The overall anti-HBs and HBsAg seropositivity rates were 44.3% and 1.2%, respectively. The anti-HBs seropositivity rate in the plasma-derived subgroup was significantly higher in both 15- and 18-year age groups. Overall response rate in the double-seronegative recipients at 15 years of age was 92.5% at 6 weeks following one recombinant HBV booster dose. Among the 24 recipients showing anti-HBs seroconversion at 6 weeks after booster, seven subjects (29.2%) had lost their anti-HBs seropositivity again within 3 years. Increased seropositivity rates and titers of anti-HBs did not provide additional protective effects among subjects comprehensively vaccinated against HBV in infancy. HBV booster strategy at 15 years of age was the main contributor to the unique age-related phenomenon of anti-HBs seropositivity rate and titer. No increase in HBsAg seropositivity rates within different age groups was observed. Vaccination with plasma-derived HBV vaccines in infancy provided higher

  19. Feasibility study for the development and marketing of magnesium seats for motor coaches and other modes of public transit

    Energy Technology Data Exchange (ETDEWEB)

    Bergeron, F. [IC-2 Technologies Inc., Quebec City, PQ (Canada); Audet, J.F. [J-F Audet Courtier Stratege, Carignan, PQ (Canada)

    2004-06-01

    Magnesium is currently used for seats in many minivans and luxury cars, as well as in some high speed trains. This paper addresses concerns about the use of magnesium in manufacturing seats for public transit vehicles. This paper aimed to validate the feasibility of magnesium and/or aluminum passenger seats and determine if they met weight and cost reduction objectives currently set by the public transportation industry. An assessment of the North American bus and motor coach market was made, and passenger seat design standards were reviewed. Additionally, magnesium samples were tested to ensure industry standards for material flammability and toxic fumes emissions during exposure to intense heat. Corrosion testing and a comparison with automobile industry tests were made. A number of manufacturing case studies were conducted, including life-cycle costs and comparisons with the manufacture of traditional steel seats. It was concluded that a lighter-weight seat is both technically possible and economically viable. In terms of flammability, magnesium seats met all required industry standards, and when combined with excellent seat design, increased the safety of seat occupants projected forward during collisions. In addition, magnesium's ability to absorb vibration was seen as a substantial benefit in terms of passenger comfort. In terms of manufacturing cost alone, a magnesium-aluminum hybrid was recommended. 15 refs., 25 tabs., 24 figs.

  20. Effectiveness of Humidification with Heat and Moisture Exchanger-booster in Tracheostomized Patients.

    Science.gov (United States)

    Gonzalez, Isabel; Jimenez, Pilar; Valdivia, Jorge; Esquinas, Antonio

    2017-08-01

    The two most commonly used types of humidifiers are heated humidifiers and heat and moisture exchange humidifiers. Heated humidifiers provide adequate temperature and humidity without affecting the respiratory pattern, but overdose can cause high temperatures and humidity resulting in condensation, which increases the risk of bacteria in the circuit. These devices are expensive. Heat and moisture exchanger filter is a new concept of humidification, increasing the moisture content in inspired gases. This study aims to determine the effectiveness of the heat and moisture exchanger (HME)-Booster system to humidify inspired air in patients under mechanical ventilation. We evaluated the humidification provided by 10 HME-Booster for tracheostomized patients under mechanical ventilation using Servo I respirators, belonging to the Maquet company and Evita 4. There was an increase in the inspired air humidity after 1 h with the humidifier. The HME-Booster combines the advantages of heat and moisture exchange minimizing the negatives. It increases the amount of moisture in inspired gas in mechanically ventilated tracheostomized patients. It is easy and safe to use. The type of ventilator used has no influence on the result.

  1. Child car seats – a habitat for house dust mites and reservoir for harmful allergens

    Directory of Open Access Journals (Sweden)

    David Clarke

    2015-02-01

    Child car seats and driver seats are habitats to a range of mite species which can be present in sufficient concentrations to cause or aggravate allergen related illnesses in individuals who are genetically predisposed.

  2. The low energy booster project status

    International Nuclear Information System (INIS)

    Tuttle, G.W.

    1993-05-01

    In order to achieve the required injection momentum, the Superconducting Super Collider (SSC) has an accelerator chain comprised of a Linear Accelerator and three synchrotrons. The Low Energy Booster (LEB) is the first synchrotron in this chain. The LEB project has made significant progress in the development of major subsystems and conventional construction. This paper briefly reviews the performance requirements of the LEB and describes significant achievements in each of the major subsystem areas. Highlighted among these achievements are the LEB foreign collaborations with the Budker Institute of Nuclear Physics (BINP) located in Novosibirsk, Russia

  3. Modeling of the YALINA booster facility by the Monte Carlo code MONK

    International Nuclear Information System (INIS)

    Talamo, A.; Gohar, Y.; Kondev, F.; Kiyavitskaya, H.; Serafimovich, I.; Bournos, V.; Fokov, Y.; Routkovskaya, C.

    2007-01-01

    The YALINA-Booster facility has been modeled according to the benchmark specifications defined for the IAEA activity without any geometrical homogenization using the Monte Carlo codes MONK and MCNP/MCNPX/MCB. The MONK model perfectly matches the MCNP one. The computational analyses have been extended through the MCB code, which is an extension of the MCNP code with burnup capability because of its additional feature for analyzing source driven multiplying assemblies. The main neutronics arameters of the YALINA-Booster facility were calculated using these computer codes with different nuclear data libraries based on ENDF/B-VI-0, -6, JEF-2.2, and JEF-3.1.

  4. An evaluation method on seat comfort based on optical motion capture

    Directory of Open Access Journals (Sweden)

    Qing TAO

    2015-10-01

    Full Text Available To research the sitting posture comfort evaluation method, through the example of comfort evaluation of the ergonomic seat and standard office seat, a methodology is introduced to evaluate the sitting posture comfort combining ergonomics theory. The proposed method is based on optical motion capture system, pressure sensor and JACK software, and TRC file is acquired by using EVART real-time capture software for identifying the spatial motion trail of human body. Then MATLAB software is used to analyze the human body motion data, and the sitting posture angle difference data for human body in different seats is acquired. TRC file is loaded into JACK software, and with the TAT REPORTER of JACK software, muscle force, moment of force and fatigue data, etc. are output, which are compared with the actual measured data from experiments, and ergonomics method is used for the evaluation. The result shows that the method of considering joint angles combining JACK software for data output is effective for evaluating sitting comfort.

  5. Controversial Swedish science minister loses seat in reshuffle

    CERN Multimedia

    Sylawan, P

    1998-01-01

    Carl Tham, who introduced sweeping changes to higher education and research, has lost his seat in a cabinet reshuffle. As science minister for 4 years he redirected funding to applied science and established new regional universities (1 page).

  6. Design and testing of an energy-absorbing crewseat for the F/FB-111 aircraft. Volume 2: Data from seat testing

    Science.gov (United States)

    Shane, S. J.

    1985-01-01

    The unacceptably high injury rate during the escape sequence (including the ejection and ground impact) of the crew module for F/FB-111 aircraft is reviewed. A program to determine if the injury potential could be reduced by replacing the existing crewseats with energy absorbing crewseats is presented. An energy absorbing test seat is designed using much of the existing seat hardware. An extensive dynamic seat test series, designed to duplicate various crew module ground impact conditions is conducted at a sled test facility. Comparative tests with operational F-111 crewseats are also conducted. After successful dynamic testing of the seat, more testing is conducted with the seats mounted in an F-111 crew module. Both swing tests and vertical drop tests are conducted. The vertical drop tests are used to obtain comparative data between the energy absorbing and operational seats. Volume 1 describes the energy absorbing test seat and testing conducted, and evaluates the data from both test series. Volume 2 presents the data obtained during the seat test series, while Volume 3 presents the data from the crew module test series.

  7. Creative thinking of design and redesign on SEAT aircraft cabin testbed: a case study

    NARCIS (Netherlands)

    Tan, C.F.; Chen, W.; Rauterberg, G.W.M.

    2009-01-01

    this paper, the intuition approach in the design and redesign of the environmental friendly innovative aircraft cabin simulator is presented.. The aircraft cabin simulator is a testbed that used for European Project SEAT (Smart tEchnologies for Stress free Air Travel). The SEAT project aims to

  8. Optimization of geometry of annular seat valves suitable for Digital Displacement fluid power pumps/motors

    DEFF Research Database (Denmark)

    Rømer, Daniel; Johansen, Per; Pedersen, Henrik C.

    2013-01-01

    Digital Displacement Fluid Power is an upcoming technology setting new standards for the achievable efficiency of fluid power pumps and motors. The core element of the Digital Displacement technology is high performance electronically controlled seat valves, which must exhibit very low flow...... work an annular seat valve suitable for use in Digital Displacement units is considered, and the ring geometry is optimized using finite element analysis including non-linear material behaviour, contact elements and fluid pressure penetrating load, closely reflecting the actual load of the seat valve...

  9. Front versus rear seat placement of children aged 12 or younger within vehicles: a rural/urban comparison in North Dakota.

    Science.gov (United States)

    Huseth-Zosel, Andrea L

    2012-01-01

    Research has shown that rear-seated children are 36 to 40 percent safer than front-seated children. Because of the substantial differences in traffic safety culture that appear to exist in rural areas and the limited research regarding seat placement and rurality, this study seeks to contribute to the safety literature by determining at what rate children are riding in the front seat and whether differences exist between rural and urban areas in regards to child front seat placement. Current child placement frequencies within vehicles were ascertained through direct observations of morning child drop-offs at randomly selected urban and rural elementary schools in eastern North Dakota during November and December of 2009, with a focus on children aged 12 or younger. Two observers wearing orange safety vests and carrying observation sheets were stationed at each elementary school a minimum of 45 min prior to each school's designated start time. Based on the vehicles that entered the school's parking lot/drop-off circle and from which a minimum of one child exited, observers were instructed to record vehicle type, presence of children in the front seat appearing to be younger than 13 years old, availability of room in the back seat, and placement of other children in the vehicle. During November and December of 2009 a total of 537 vehicles were observed at urban schools and 150 vehicles were observed at rural schools. Of the 537 vehicles observed at urban schools, 28.7 percent had children seated in the front seat, whereas 41.3 percent of the 150 vehicles observed at rural schools had front-seated children. Significant urban/rural differences exist in child seat placement, with vehicles in rural areas much more likely to be carrying front-seated children than vehicles in urban areas. Based on a sample of vehicles observed at urban and rural elementary schools in North Dakota, the results of this study indicate that there are significant rural/urban differences in

  10. Pertussis circulation has increased T-cell immunity during childhood more than a second acellular booster vaccination in Dutch children 9 years of age.

    Directory of Open Access Journals (Sweden)

    Rose-Minke Schure

    Full Text Available UNLABELLED: Here we report the first evaluation of T-cell responses upon a second acellular pertussis booster vaccination in Dutch children at 9 years of age, 5 years after a preschool booster vaccination. Blood samples of children 9 years of age were studied longitudinally until 1 year after the second aP booster and compared with those after the first aP booster in children 4 and 6 years of age from a cross-sectional study. After stimulation with pertussis-vaccine antigens, Th1, Th2 and Th17 cytokine responses were measured and effector memory cells (CCR7-CD45RA- were characterized by 8-colour FACS analysis. The second aP booster vaccination at pre-adolescent age in wP primed individuals did increase pertussis-specific Th1 and Th2 cytokine responses. Noticeably, almost all T-cell responses had increased with age and were already high before the booster vaccination at 9 years of age. The enhancement of T-cell immunity during the 5 year following the booster at 4 years of age is probably caused by natural boosting due to the a high circulation of pertussis. However, the incidence of pertussis is high in adolescents and adults who have only received the Dutch wP vaccine during infancy and no booster at 4 years of age. Therefore, an aP booster vaccination at adolescence or later in these populations might improve long-term immunity against pertussis and reduce the transmission to the vulnerable newborns. TRIAL REGISTRATION: Controlled-Trials.com ISRCTN64117538.

  11. Results from the AGS Booster transverse damper

    International Nuclear Information System (INIS)

    Russo, D.; Brennan, M.; Meth, M.; Roser, T.

    1993-01-01

    To reach the design intensity of 1.5 x 10 13 protons per pulse in the AGS Booster, transverse coupled bunch instabilities with an estimated growth rate of 1500s -1 have to be dampened. A prototype transverse damper has been tested successfully using a one turn digital delay and closed orbit suppression implemented in a programmable gate array. An updated damper, which includes an algorithm to optimize damping for a changing betatron rune, will also be presented

  12. Performance robustness of a magnetorheological seat suspension to temperature variations using skyhook control

    Science.gov (United States)

    Wilson, Nicholas L.; Wereley, Norman M.; Choi, Young-Tai; Hiemenz, Gregory J.; Hu, Wei

    2009-03-01

    The harmonic steady-state responses of an MR seat isolator, designed and fabricated at the University of Maryland for the driver/commander seat of the Expeditionary Fighting Vehicle (EFV), are measured over a temperature range from 100°C to 1000°C, and the damper behavior is characterized using a variant of the nonlinear Bingham plastic model. The effect of damper self-heating on the model parameters is investigated and the trends with temperature variation are presented. Numerical simulations are carried out to investigate seat isolation performance across a broad frequency spectrum as temperature and payload vary. Conclusions are drawn about the performance robustness to temperature variations of the semi-active skyhook control algorithm typically utilized in vibration isolation problems.

  13. Booster HBV vaccination; is it really necessary? | Alavian | Egyptian ...

    African Journals Online (AJOL)

    Egyptian Journal of Pediatric Allergy and Immunology (The). Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 9, No 2 (2011) >. Log in or Register to get access to full text downloads. Username, Password, Remember me, or Register. Booster HBV vaccination; is it ...

  14. Availability, functionality, and use of seat belts in Beijing taxis prior to the 2008 Beijing Olympic Games.

    Science.gov (United States)

    Fleiter, Judy J; Gao, Liping; Qiu, Chen; Shi, Kan

    2009-03-01

    Use of driver seat belts and availability and functionality of passenger seat belts in a convenience sample of 231 Beijing taxis were examined in the months prior to the 2008 Beijing Olympic Games. Driver and front passenger seat belt use was mandated in China from 2004 to help address the growing public health crisis of road trauma. Results from observations made by in-vehicle passengers revealed that 21.2% of drivers were correctly wearing a belt, approximately half were not, and one third were using the belt in a non-functional way. Over 3/4 of this sample of taxi drivers were unrestrained while working. The percentage of functionally available belts was higher for front than rear passengers (88.3% and 22.9%, respectively). This low rate of belt availability in rear seats calls into question the preparedness of the fleet to cater for the safety needs of foreign visitors to China, particularly those from countries with high levels of restraint use. Factors influencing the use/misuse of seat belts in China remain largely unexplored. Results of this pilot study support further investigations of barriers to using injury prevention mechanisms such as seat belts in less motorised countries.

  15. A social media program to increase adolescent seat belt use.

    Science.gov (United States)

    Drake, Stacy A; Zhang, Ni; Applewhite, Courtney; Fowler, Katherine; Holcomb, John B

    2017-09-01

    In response to motor vehicle crashes remaining the leading cause of death for teenagers in the United States, a nursing clinical group (n = 10) in conjunction with a local hospital injury prevention program created an educational campaign to bolster seat belt use. The nursing students created an Instagram account to serve as an educational tool to promote seat belt use among teenagers aged 14-19, and the program was presented at three high school health fairs. In all, 135 postings were made to the account over a 3-month period. The number of likes posted by high school students was the unit of analysis. The most significant result (p = .01) was the difference between postings most liked (celebrities wearing seat belts) and least liked (postings made at the high school health fair), otherwise, differences among postings liked (humor postings, response requests, pictures of celebrities, factual data) were not significant. Instagram user engagement, measured in number of likes, is indicative that social media provides platforms to promote injury prevention efforts. Further research is needed to identify measurable elements of social media and to follow-up on behavioral changes following participation. © 2017 Wiley Periodicals, Inc.

  16. The seat of ground water discharge as ore-mabilizing factor in the formatian of hydrogenic uranium deposits

    International Nuclear Information System (INIS)

    Natal'chenko, B.I.; Gol'dshtejn, R.I.

    1982-01-01

    The role of structural-hydrogeological factor in the process of ore-controlling zoning development during hydrogeneous deposit formation is discussed, as reflecting in the most objective way the spreading of stratal oxidation zones and morphology of uranium mineralization as regards discharge seats because there are only they which mobilize stratal waters for active displacement. The types of discharge seats of stratal waters and their effect on formation of ore-controlling zones of stratal oxidation with uranium mineralization are presented. The conclusion is drawn that local and regional discharge seats of stratal waters dictate both the spacing of regional fronts of stratal-oxidized rocks and their ore content degree. The displacement of discharge seats or their growing into local regions of alimentation results in reorganization of the total ore-controlling zoning, which enables to consider the seats of water discharge as ore-mobilizing structures in the formation of hydrogenic uranium deposits

  17. Power Supply of the Booster Magnets for the ILSF Synchrotron

    Directory of Open Access Journals (Sweden)

    O Ahmadi

    2017-08-01

    Full Text Available The Iranian Light Source Facility (ILSF booster main specifications including 250 ms ramp up, 2Hz repetition rate, and quasi-sinusoidal wave shape, up to this point have been the basis for calculations. Each family of magnets including Dipole, Quadrupole and Sextupoles will feed by individual power supply. In order to maintain constant transverse tunes and chromaticity while the beam is accelerated, quadrupole and sextupole magnet currents must closely track the current in the dipole magnets. In booster rings, feeding the high inductance load, tracking of Quadrupole and sextupole magnets, reducing output current fluctuation and having a precise high bandwidth current regulation system are particular challenges. In order to meet the requirements, it is necessary to have a fully digital controller to achieve a fast regulation system. The prototype power supply and its test results are described in this paper  

  18. Modeling and Analysis of Static and Dynamic Characteristics of Nonlinear Seat Suspension for Off-Road Vehicles

    OpenAIRE

    Yan, Zhenhua; Zhu, Bing; Li, Xuefei; Wang, Guoqiang

    2015-01-01

    Low-frequency vibrations (0.5–5 Hz) that harm drivers occur in off-road vehicles. Thus, researchers have focused on finding methods to effectively isolate or control low-frequency vibrations. A novel nonlinear seat suspension structure for off-road vehicles is designed, whose static characteristics and seat-human system dynamic response are modeled and analyzed, and experiments are conducted to verify the theoretical solutions. Results show that the stiffness of this nonlinear seat suspension...

  19. The AGS Booster vacuum systems

    International Nuclear Information System (INIS)

    Hseuh, H.C.

    1989-01-01

    The AGS Booster is a synchrotron for the acceleration of both protons and heavy ions. The design pressure of low 10 -11 mbar is required to minimize beam loss of the partially stripped heavy ions. To remove contaminants and to reduce outgassing, the vacuum chambers and the components located in them will be chemically cleaned, vacuum fired, baked then treated with nitric oxide. The vacuum sector will be insitu baked to a minimum of 200 degree C and pumped by the combination of sputter ion pumps and titanium sublimation pumps. This paper describes the design and the processing of this ultra high vacuum system, and the performance of some half-cell vacuum chambers. 9 refs., 7 figs

  20. Nasal obstruction and sleep-disordered breathing: the effect of supine body position on nasal measurements in snorers.

    Science.gov (United States)

    Virkkula, Paula; Maasilta, Paula; Hytönen, Maija; Salmi, Tapani; Malmberg, Henrik

    2003-06-01

    Nasal obstruction is considered to be a potential etiological factor in sleep-disordered breathing. However, a significant correlation between nasal measurements and obstructive sleep apnea has not been demonstrated so far. The aim of this study was to investigate the relationships between nasal resistance, nasal volumes and selected sleep parameters using nasal measurements performed in both seated and supine positions. We also investigated whether snoring patients in our clinical sample showed increased positional or decongestive nasal mucosal changes. Forty-one snoring men on a waiting list for correction of nasal obstruction underwent polysomnography, anterior rhinomanometry and acoustic rhinometry. Nineteen non-snoring control subjects were also recruited. Nasal measurements were performed in a seated position, after lying down in a supine position and, after decongestion of nasal mucosa, in a seated position again. In the overall patient group, nasal volume at a distance 2-4 cm from the nares in the supine position correlated inversely with apnea-hypopnea index (AHI) (r = -0.32, p patients, total nasal resistance measured in a supine position correlated with AHI (r = 0.50, p position and sleep parameters. Postural or decongestive changes in nasal measurements were not increased in snoring patients compared with control subjects. The relationship found between nasal measurements and sleep parameters suggests that nasal obstruction does augment airway collapse.

  1. Detecting MOV stem to stem-nut lubricant degradation by reviewing MOV open-quotes seating timeclose quotes

    International Nuclear Information System (INIS)

    Loweth, W.A.

    1996-01-01

    The objective is to describe a methodology, suitable for IST Programs, that obtains sufficient data to assess and trend the overall condition of AC and DC MOVs. Using existing diagnostic test equipment, recording the time from Hard Seat Contact to the Torque Switch Trip point (TST), open-quote Seating Time (msec)close quotes, can provide a means to quickly detect for signs of lubricant degradation in the interface between the stem and stem-nut for MOVs. Obtaining and trending the open-quote Seating Time close-quote parameter can be easily accomplished using the sensors which provide motor current, torque or thrust. From the initial baseline test to subsequent tests, it is the change in time between Hard Seat Contact to Torque Switch Trip point that is utilized to monitor changes in the coefficient of friction between the stem and stem-nut. While many Licensees have begun their MOV Periodic Verification Programs, obtaining the open-quotes Seating Timeclose quotes during Refueling Outages and comparing the results from subsequent outages can be an input to the justification for changing the MOV baseline test frequency

  2. 49 CFR 392.16 - Use of seat belts.

    Science.gov (United States)

    2010-10-01

    ... Transportation Other Regulations Relating to Transportation (Continued) FEDERAL MOTOR CARRIER SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR CARRIER SAFETY REGULATIONS DRIVING OF COMMERCIAL MOTOR VEHICLES Driving of Commercial Motor Vehicles § 392.16 Use of seat belts. A commercial motor vehicle which...

  3. Classroom Management: Seating Solutions [and] Hooray for Volunteers.

    Science.gov (United States)

    Novelli, Joan; Edgar, Susan

    1997-01-01

    Two articles present suggestions for enhancing classroom management in creative ways. The first article describes how to use flexible seating arrangements to encourage cooperation, friendship, and community. The second article discusses how to encourage and work with classroom volunteers from the community. (SM)

  4. REDUCING THE BOOSTER STATIONS ENERGY CONSUMPTION BY WAY OF ELIMINATING OVERPRESSURE IN THE WATER SUPPLY NETWORK

    Directory of Open Access Journals (Sweden)

    G. N. Zdor

    2015-01-01

    Full Text Available The energy efficiency improvement of the city housing-and-utilities infrastructure and watersupply and water-disposal systems poses an occurrent problem. The water-supply systems energy consumption sizable share falls on the pump plants. The article deals with the issues of the operating regime management of the existing booster stations equipped with a group of pumping units regulated with frequency converters. One of the optimization directions of their energy consumption is the reduction of over-pressure in the water-distribution network and its sustentation within the regulatory values. The authors offer the structure and methodology of the data collection-and-analysis automated system utilization for revealing and eliminating the overpressure in the water-supply network. This system is designed for the group management of booster-stations operating regimes on the ground of data obtained from the pressure controlling devices at the consumers. The data exchange in the system is realized via GSM.The paper presents results of the tests carried out at the booster stations in some major cities of the Republic of Belarus. The authors analyze dependence of overpressure in the network on the methods of the plant output pressure sustentation (daily graph or constant pressure. The authors study the elimination effect of over-pressure in the water distribution network on changing the booster station pumping units operation regimes. The study shows that eliminating over pressure in the water distributing network leads to lowering the booster station pressure. This in its turn decreases its energy consumption by 15–20 % depending on the over pressure fixed level.

  5. Electron cooling system in the booster synchrotron of the HIAF project

    Energy Technology Data Exchange (ETDEWEB)

    Mao, L.J., E-mail: maolijun@impcas.ac.cn [Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Yang, J.C.; Xia, J.W.; Yang, X.D.; Yuan, Y.J.; Li, J.; Ma, X.M.; Yan, T.L.; Yin, D.Y.; Chai, W.P.; Sheng, L.N. [Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Shen, G.D.; Zhao, H.; Tang, M.T. [Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Graduate University of Chinese Academy of Sciences, Beijing 100049 (China)

    2015-06-21

    The High Intensity heavy ion Accelerator Facility (HIAF) is a new accelerator complex under design at the Institute of Modern Physics (IMP). The facility is aiming at the production of high intensity heavy ion beams for a wide range of experiments in high energy density physics, nuclear physics, atomic physics and other applications. It consists of a superconducting electron-cyclotron-resonance ion source and an intense proton ion source, a linear accelerator, a 34 Tm booster synchrotron ring, a 43 Tm multifunction compression synchrotron ring, a 13 Tm high precision spectrometer ring and several experimental terminals. A magnetized electron cooling device is supposed to be used in the booster ring for decreasing the transverse emittance of injected beams. The conceptual design and main parameters of this cooler are presented in this paper.

  6. Development of hydraulic brake actuator for active brake control; Active brake seigyoyo yuatsu booster no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Konishi, Y; Hattori, M. Sugisawa, M.; Nishii, M [Aisin Seiki Co. Ltd., Aichi (Japan)

    1997-10-01

    Recently, application of active brake control systems of the vehicle are increasing. (Vehicle stability control, Panic brake assist ) We have developed a new hydraulic brake actuator for active brake control systems. New hydraulic brake actuator is composed of the three parts. (Hydraulic booster unit, Power supply unit, Control valve unit) This report describes the construction of the new hydraulic booster unit. 2 refs., 10 figs.

  7. The seated bus passenger--a review.

    Science.gov (United States)

    Levis, J A

    1978-09-01

    The paper describes the inter-relationship of anthropometry, rig studies and dynamic testing of aspects related to problems of the seated bus passenger. It seeks to draw together sub-sections of a very large study sponsored by the government through the Transport and Road Research Laboratory and undertaken by the Human Factors Group of Leyland Truck and Bus. It is relevant to all those designing passenger carrying transport systems.

  8. Using naturalistic driving data to identify variables associated with infrequent, occasional, and consistent seat belt use.

    Science.gov (United States)

    Reagan, Ian J; McClafferty, Julie A; Berlin, Sharon P; Hankey, Jonathan M

    2013-01-01

    Seat belt use is one of the most effective countermeasures to reduce traffic fatalities and injuries. The success of efforts to increase use is measured by road side observations and self-report questionnaires. These methods have shortcomings, with the former requiring a binary point estimate and the latter being subjective. The 100-car naturalistic driving study presented a unique opportunity to study seat belt use in that seat belt status was known for every trip each driver made during a 12-month period. Drivers were grouped into infrequent, occasional, or consistent seat belt users based on the frequency of belt use. Analyses were then completed to assess if these groups differed on several measures including personality, demographics, self-reported driving style variables as well as measures from the 100-car study instrumentation suite (average trip speed, trips per day). In addition, detailed analyses of the occasional belt user group were completed to identify factors that were predictive of occasional belt users wearing their belts. The analyses indicated that consistent seat belt users took fewer trips per day, and that increased average trip speed was associated with increased belt use among occasional belt users. The results of this project may help focus messaging efforts to convert occasional and inconsistent seat belt users to consistent users. Copyright © 2012 Elsevier Ltd. All rights reserved.

  9. Exercise, Manual Therapy, and Booster Sessions in Knee Osteoarthritis: Cost-Effectiveness Analysis From a Multicenter Randomized Controlled Trial.

    Science.gov (United States)

    Bove, Allyn M; Smith, Kenneth J; Bise, Christopher G; Fritz, Julie M; Childs, John; Brennan, Gerard P; Abbott, J Haxby; Fitzgerald, G Kelley

    2018-01-01

    Limited information exists regarding the cost-effectiveness of rehabilitation strategies for individuals with knee osteoarthritis (OA). The study objective was to compare the cost-effectiveness of 4 different combinations of exercise, manual therapy, and booster sessions for individuals with knee OA. This economic evaluation involved a cost-effectiveness analysis performed alongside a multicenter randomized controlled trial. The study took place in Pittsburgh, Pennsylvania; Salt Lake City, Utah; and San Antonio, Texas. The study participants were 300 individuals taking part in a randomized controlled trial investigating various physical therapy strategies for knee OA. Participants were randomized into 4 treatment groups: exercise only (EX), exercise plus booster sessions (EX+B), exercise plus manual therapy (EX+MT), and exercise plus manual therapy and booster sessions (EX+MT+B). For the 2-year base case scenario, a Markov model was constructed using the United States societal perspective and a 3% discount rate for costs and quality-adjusted life years (QALYs). Incremental cost-effectiveness ratios were calculated to compare differences in cost per QALY gained among the 4 treatment strategies. In the 2-year analysis, booster strategies (EX+MT+B and EX+B) dominated no-booster strategies, with both lower health care costs and greater effectiveness. EX+MT+B had the lowest total health care costs. EX+B cost ${\\$}$1061 more and gained 0.082 more QALYs than EX+MT+B, for an incremental cost-effectiveness ratio of ${\\$}$12,900/QALY gained. The small number of total knee arthroplasty surgeries received by individuals in this study made the assessment of whether any particular strategy was more successful at delaying or preventing surgery in individuals with knee OA difficult. Spacing exercise-based physical therapy sessions over 12 months using periodic booster sessions was less costly and more effective over 2 years than strategies not containing booster sessions for

  10. Low Energy Electron Cooler for NICA Booster

    CERN Document Server

    Denisov, A P

    2017-01-01

    BINP has developed an electron cooler to increase the ion accumulation efficiency in the NICA (Nuclotron-based Ion Collider fAcility) heavy ion booster (JINR, Dubna). Adjustment of the cooler magnetic system provides highly homogeneous magnetic field in the cooling section B trans/B long ≤ 4∙10-5 which is vital for efficient electron cooling. First experiments with an electron beam performed at BINP demonstrated the target DC current of 500 mA and electron energy 6 keV.

  11. The influence of parental education and other socio-economic factors on child car seat use.

    Science.gov (United States)

    Rok Simon, Mateja; Korošec, Aleš; Bilban, Marjan

    2017-03-01

    The behaviour of parents in ensuring car passenger safety for their children is associated with socio-economic (SE) status of the family; however, the influence of parental education has rarely been researched and the findings are contradictory. The aim of the study was to clarify whether parental education influences the use of a child car seat during short rides. A cross-sectional survey was carried out in outpatient clinics for children's healthcare across Slovenia. 904 parents of 3-year-old children participated in the study; the response rate was 95.9%. A self-administered questionnaire was used. A binary multiple logistic regression was applied to assess the association between parental unsafe behaviour as dependent variable, and education and other SE factors as independent variables. 14.6% of parents did not use a child car seat during short rides. Families where mother had low or college education had higher odds of the non-use of a child car seat than families where mother had a university education. Single-parent families and those who lived in areas with low or medium SE status also had higher odds of the non-use of a child car seat. Low educational attainment influences parents' behaviour regarding the non-use of a child car seat. Low parental education is not the only risk factor since some highly educated parents also have high odds of unsafe behaviour. All parents should therefore be included in individually tailored safety counselling programmes. SE inequalities could be further reduced with provision of free child car seats for eligible families.

  12. Comparison between a Computational Seated Human Model and Experimental Verification Data

    Directory of Open Access Journals (Sweden)

    Christian G. Olesen

    2014-01-01

    Full Text Available Sitting-acquired deep tissue injuries (SADTI are the most serious type of pressure ulcers. In order to investigate the aetiology of SADTI a new approach is under development: a musculo-skeletal model which can predict forces between the chair and the human body at different seated postures. This study focuses on comparing results from a model developed in the AnyBody Modeling System, with data collected from an experimental setup. A chair with force-measuring equipment was developed, an experiment was conducted with three subjects, and the experimental results were compared with the predictions of the computational model. The results show that the model predicted the reaction forces for different chair postures well. The correlation coefficients of how well the experiment and model correlate for the seat angle, backrest angle and footrest height was 0.93, 0.96, and 0.95. The study show a good agreement between experimental data and model prediction of forces between a human body and a chair. The model can in the future be used in designing wheelchairs or automotive seats.

  13. Seat pan and backrest pressure distribution while sitting in office chairs.

    Science.gov (United States)

    Zemp, Roland; Taylor, William R; Lorenzetti, Silvio

    2016-03-01

    Nowadays, an increasing amount of time is spent seated, especially in office environments, where sitting comfort and support are increasingly important due to the prevalence of musculoskeletal disorders. The aim of this study was to develop a methodology for chair-specific sensor mat calibration, to evaluate the interconnections between specific pressure parameters and to establish those that are most meaningful and significant in order to differentiate pressure distribution measures between office chairs. The shape of the exponential calibration function was highly influenced by the material properties and geometry of the office chairs, and therefore a chair-specific calibration proved to be essential. High correlations were observed between the eight analysed pressure parameters, whereby the pressure parameters could be reduced to a set of four and three parameters for the seat pan and the backrest respectively. In order to find significant differences between office chairs, gradient parameters should be analysed for the seat pan, whereas for the backrest almost all parameters are suitable. Copyright © 2015 Elsevier Ltd and The Ergonomics Society. All rights reserved.

  14. On the Modeling of a MEMS Based Capacitive Accelerometer for Measurement of Tractor Seat Vibration

    Directory of Open Access Journals (Sweden)

    M. Alidoost

    2010-04-01

    Full Text Available Drivers of heavy vehicles often face with higher amplitudes of frequencies range between 1-80 Hz. Hence, this range of frequency results in temporary or even sometimes permanent damages to the health of drivers. Examples for these problems are damages to the vertebral column and early tiredness, which both reduce the driver’s performance significantly. One solution to this problem is to decrease the imposed vibration to the driver’s seat by developing an active seat system. These systems require an online measuring unit to sense vibrations transferred to the seat. The measuring unit can include a capacitive micro-accelerometer on the basis of MEMS which measure online vibrations on the seat. In this study, the mechanical behavior of a capacitive micro-accelerometer for the vibration range applied to a tractor seat has been simulated. The accelerometer is capable to measure step, impact and harmonic external excitations applied to the system. The results of the study indicate that, with increasing the applied voltage, the system sensitivity also increases, but the measuring range of vibrations decreases and vice versa. The modeled accelerometer, at damping ratio of 0.67 is capable to measure accelerations within the frequency range of lower than 130 Hz.

  15. A subjective framework for seat comfort based on a heuristic multi criteria decision making technique and anthropometry.

    Science.gov (United States)

    Fazlollahtabar, Hamed

    2010-12-01

    Consumer expectations for automobile seat comfort continue to rise. With this said, it is evident that the current automobile seat comfort development process, which is only sporadically successful, needs to change. In this context, there has been growing recognition of the need for establishing theoretical and methodological automobile seat comfort. On the other hand, seat producer need to know the costumer's required comfort to produce based on their interests. The current research methodologies apply qualitative approaches due to anthropometric specifications. The most significant weakness of these approaches is the inexact extracted inferences. Despite the qualitative nature of the consumer's preferences there are some methods to transform the qualitative parameters into numerical value which could help seat producer to improve or enhance their products. Nonetheless this approach would help the automobile manufacturer to provide their seats from the best producer regarding to the consumers idea. In this paper, a heuristic multi criteria decision making technique is applied to make consumers preferences in the numeric value. This Technique is combination of Analytical Hierarchy Procedure (AHP), Entropy method, and Technique for Order Preference by Similarity to an Ideal Solution (TOPSIS). A case study is conducted to illustrate the applicability and the effectiveness of the proposed heuristic approach. Copyright © 2010 Elsevier Ltd. All rights reserved.

  16. Ultra-short-course booster is effective in recurrent grass pollen-induced allergic rhinoconjunctivitis.

    Science.gov (United States)

    Pfaar, O; Lang, S; Pieper-Fürst, U; Astvatsatourov, A; Gerich, F; Klimek, L; Kramer, M F; Reydelet, Y; Shah-Hosseini, K; Mösges, R

    2018-01-01

    A relevant proportion of allergic rhinoconjunctivitis (ARC) patients experience recurrent symptoms after successfully completing allergen immunotherapy (AIT). This prospective, controlled, noninterventional study used internationally standardized instruments to determine the clinical effects of a preseasonal, ultra-short-course booster AIT on clinical outcome parameters. This two-arm study included patients aged ≥12 years with recurrent grass pollen-induced seasonal AR who had completed a successful course of any grass pollen AIT at least 5 years before enrolment. Overall, 56 patients received one preseasonal short-course booster AIT using tyrosine-absorbed grass pollen allergoids containing the adjuvant monophosphoryl lipid A (MPL ® ); 51 control patients received symptomatic medication. The combined symptom and medication score (CSMS) was recorded in the (peak) grass pollen season. Furthermore, concomitant (antiallergic) medication use, the patients' state of health, Mini Rhinoconjunctivitis Quality of Life Questionnaire (MiniRQLQ) results and safety/tolerability of the treatment were assessed. The CSMS in the peak grass pollen season was significantly lower in the booster AIT group (Δ=38.4%, Pallergoids containing the adjuvant MPL ® effectively prevents re-occurrence of symptoms in patients with grass pollen-induced ARC. © 2017 The Authors. Allergy Published by John Wiley & Sons Ltd.

  17. Active immunisation of horses against tetanus including the booster dose and its application.

    Science.gov (United States)

    Liefman, C E

    1981-02-01

    Successful active immunisation of horses against tetanus is dependent on a number of factors of which the toxoid preparation used, its method of application and the ability of the individual horse to respond are fundamental. Two immunisation schedules using an aluminium-based toxoid preparation were examined and the protection determined by monitoring the level of antitoxin afforded by each schedule. The results obtained demonstrated that 2 doses of this toxoid are necessary to ensure 12 months protection in all horses. These results are discussed in relation to the factors involved in active immunisation against tetanus. Reference is also made to the occurrence of a transient phase of reduced levels of antitoxin following booster doses of toxoid in immunised horses during which it is considered these horses could become more susceptible to tetanus. The effect of a booster dose on immunised horses was examined and while there can be a reduction in the level of antitoxin in some immunised horses following this dose its effect is minimal, short-lived and for all practical purposes can be disregarded. The application of the booster dose in practice is also discussed.

  18. Variation between seated and standing/walking postures among male and female call centre operators

    Directory of Open Access Journals (Sweden)

    Toomingas Allan

    2012-03-01

    Full Text Available Abstract Background The dose and time-pattern of sitting has been suggested in public health research to be an important determinant of risk for developing a number of diseases, including cardiovascular disorders and diabetes. The aim of the present study was to assess the time-pattern of seated and standing/walking postures amongst male and female call centre operators, on the basis of whole-shift posture recordings, analysed and described by a number of novel variables describing posture variation. Methods Seated vs. standing/walking was recorded using dichotomous inclinometers throughout an entire work shift for 43 male and 97 female call centre operators at 16 call centres. Data were analysed using an extensive set of variables describing occurrence of and switches between seated and standing/walking, posture similarity across the day, and compliance with standard recommendations for computer work. Results The majority of the operators, both male and female, spent more than 80% of the shift in a seated posture with an average of 10.4 switches/hour between seated and standing/walking or vice versa. Females spent, on average, 11% of the day in periods of sustained sitting longer than 1 hour; males 4.6% (p = 0.013. Only 38% and 11% of the operators complied with standard recommendations of getting an uninterrupted break from seated posture of at least 5 or 10 minutes, respectively, within each hour of work. Two thirds of all investigated variables showed coefficients of variation between subjects above 0.5. Since work tasks and contractual break schedules were observed to be essentially similar across operators and across days, this indicates that sedentary behaviours differed substantially between individuals. Conclusions The extensive occurrence of uninterrupted seated work indicates that efforts should be made at call centres - and probably in other settings in the office sector - to introduce more physical variation in terms of standing

  19. Preparations for Upgrading the RF Systems of the PS Booster

    CERN Document Server

    Albright, Simon; Shaposhnikova, Elena

    2016-01-01

    The accelerators of the LHC injector chain need to be upgraded to provide the HL-LHC beams. The PS Booster, the first synchrotron in the LHC injection chain, uses three different RF systems (first, second and up to tenth harmonic) in each of its four rings. As part of the LHC Injector Upgrade the current ferrite RF systems will be replaced with broadband Finemet cavities, increasing the flexibility of the RF system. A Finemet test cavity has been installed in Ring 4 to investigate its effect on machine performance, especially beam stability, during extensive experimental studies. Due to large space charge impedance Landau damping is lost through most of the cycle in single harmonic operation, but is recovered when using the second harmonic and controlled longitudinal emittance blow-up. This paper compares beam parameters during acceleration with and without the Finemet test cavity. Comparisons were made using beam measurements and simulations with the BLonD code based on a full PS Booster impedance model. Thi...

  20. Explaining state-to-state differences in seat belt use : an analysis of socio-demographic variables.

    Science.gov (United States)

    2011-02-01

    "Despite the extensive evidence about the benefits of seat belt use, there is a great deal of variation in use within the US. For example, the national average for seat belt use in 2009 was 84 percent while the state-level averages ranged from 68 per...

  1. Perpendicular biased ferrite tuned RF cavity for the TRIUMF KAON Factory booster ring

    International Nuclear Information System (INIS)

    Poirier, R.L.; Enegren, T.; Haddock, C.

    1989-03-01

    The rf cavity for the booster ring requires a frequency swing of 46 MHz to 62 MHz at a repetition rate of 50 Hz. The possibility of using the LANL booster cavity design with a yttrium garnet ferrite tuner biased perpendicular to the rf field, in the longitudinal direction, is being investigated. In order to minimize the stray magnetic biasing field on the beam axis, an alternative scheme similar to the design being proposed for the LANL main ring cavity in which the ferrite is perpendicular biased in the radial direction, is being considered. The behaviour of the rf cavity and the magnetizing circuit for both designs are discussed

  2. 77 FR 57481 - Special Conditions: Embraer S.A., Models EMB-135 and EMB-145 Series; Airplane Seats with Non...

    Science.gov (United States)

    2012-09-18

    ... flammability of seat cushions. With the seat design being mostly fabric and metal, the contribution to a fire..., large, non-metallic panels that would affect survivability during a post-crash fire event. The.... At the time the applicable rules were written, seats were designed with a metal frame covered by...

  3. Staying Safe in the Car and on the Bus

    Science.gov (United States)

    ... a booster! Get in the Back Here's another important safety rule: Sit in the back seat. Kids 12 ... or band concerts once in a while, it's important to follow these rules. When you see the bus driving up, everyone waiting should get into a line. ...

  4. FDTD calculations of specific energy absorption rate in a seated voxel model of the human body from 10 MHz to 3 GHz

    Energy Technology Data Exchange (ETDEWEB)

    Findlay, R P; Dimbylow, P J [Health Protection Agency, Chilton, Didcot, Oxon OX11 0RQ (United Kingdom)

    2006-05-07

    Finite-difference time-domain (FDTD) calculations have been performed to investigate the frequency dependence of the specific energy absorption rate (SAR) in a seated voxel model of the human body. The seated model was derived from NORMAN (NORmalized MAN), an anatomically realistic voxel phantom in the standing posture with arms to the side. Exposure conditions included both vertically and horizontally polarized plane wave electric fields between 10 MHz and 3 GHz. The resolution of the voxel model was 4 mm for frequencies up to 360 MHz and 2 mm for calculations in the higher frequency range. The reduction in voxel size permitted the calculation of SAR at these higher frequencies using the FDTD method. SAR values have been calculated for the seated adult phantom and scaled versions representing 10-, 5- and 1-year-old children under isolated and grounded conditions. These scaled models do not exactly reproduce the dimensions and anatomy of children, but represent good geometric information for a seated child. Results show that, when the field is vertically polarized, the sitting position causes a second, smaller resonance condition not seen in resonance curves for the phantom in the standing posture. This occurs at {approx}130 MHz for the adult model when grounded. Partial-body SAR calculations indicate that the upper and lower regions of the body have their own resonant frequency at {approx}120 MHz and {approx}160 MHz, respectively, when the grounded adult model is orientated in the sitting position. These combine to produce this second resonance peak in the whole-body averaged SAR values calculated. Two resonance peaks also occur for the sitting posture when the incident electric field is horizontally polarized. For the adult model, the peaks in the whole-body averaged SAR occur at {approx}180 and {approx}600 MHz. These peaks are due to resonance in the arms and feet, respectively. Layer absorption plots and colour images of SAR in individual voxels show the

  5. FDTD calculations of specific energy absorption rate in a seated voxel model of the human body from 10 MHz to 3 GHz

    International Nuclear Information System (INIS)

    Findlay, R P; Dimbylow, P J

    2006-01-01

    Finite-difference time-domain (FDTD) calculations have been performed to investigate the frequency dependence of the specific energy absorption rate (SAR) in a seated voxel model of the human body. The seated model was derived from NORMAN (NORmalized MAN), an anatomically realistic voxel phantom in the standing posture with arms to the side. Exposure conditions included both vertically and horizontally polarized plane wave electric fields between 10 MHz and 3 GHz. The resolution of the voxel model was 4 mm for frequencies up to 360 MHz and 2 mm for calculations in the higher frequency range. The reduction in voxel size permitted the calculation of SAR at these higher frequencies using the FDTD method. SAR values have been calculated for the seated adult phantom and scaled versions representing 10-, 5- and 1-year-old children under isolated and grounded conditions. These scaled models do not exactly reproduce the dimensions and anatomy of children, but represent good geometric information for a seated child. Results show that, when the field is vertically polarized, the sitting position causes a second, smaller resonance condition not seen in resonance curves for the phantom in the standing posture. This occurs at ∼130 MHz for the adult model when grounded. Partial-body SAR calculations indicate that the upper and lower regions of the body have their own resonant frequency at ∼120 MHz and ∼160 MHz, respectively, when the grounded adult model is orientated in the sitting position. These combine to produce this second resonance peak in the whole-body averaged SAR values calculated. Two resonance peaks also occur for the sitting posture when the incident electric field is horizontally polarized. For the adult model, the peaks in the whole-body averaged SAR occur at ∼180 and ∼600 MHz. These peaks are due to resonance in the arms and feet, respectively. Layer absorption plots and colour images of SAR in individual voxels show the specific regions in which the

  6. Fabrics for fire resistant passenger seats in aircraft

    Science.gov (United States)

    Tesoro, G. C.

    1978-01-01

    The essential elements of the problem and of approaches to improved fire resistance in aircraft seats are reviewed. The performance requirements and availability of materials, delay in the ignition of upholstery fabric by a small source are considered a realistic objective. Results of experimental studies on the thermal response of fabrics and fabric/foam combinations suggest significant conclusions regarding: (1) the ignition behavior of a commercial 90/10 wool/nylon upholstery fabric relative to fabrics made from thermally stable polymers; (2) the role of the foam backing; (3) the behavior of seams. These results, coupled with data from other sources, also confirm the importance of materials' interactions in multicomponent assemblies, and the need for system testing prior to materials' selection. The use of an interlinear or thermal barrier between upholstery fabric and foam is a promising and viable approach to improved fire resistance of the seat assembly, but experimental evaluation of specific combinations of materials or systems is an essential part of the selection process.

  7. A new one-man submarine is tested as vehicle for solid rocket booster retrieval

    Science.gov (United States)

    2000-01-01

    - The one-man submarine known as DeepWorker 2000 is tested in Atlantic waters near Cape Canaveral, Fla. Nearby are divers; inside the sub is the pilot, Anker Rasmussen. The sub is being tested on its ability to duplicate the sometimes hazardous job United Space Alliance (USA) divers perform to recover the expended boosters in the ocean after a launch. The boosters splash down in an impact area about 140 miles east of Jacksonville and after recovery are towed back to KSC for refurbishment by the specially rigged recovery ships. DeepWorker 2000 will be used in a demonstration during retrieval operations after the upcoming STS-101 launch. The submarine pilot will demonstrate capabilities to cut tangled parachute riser lines using a manipulator arm and attach a Diver Operator Plug to extract water and provide flotation for the booster. DeepWorker 2000 was built by Nuytco Research Ltd., North Vancouver, British Columbia. It is 8.25 feet long, 5.75 feet high, and weighs 3,800 pounds. USA is a prime contractor to NASA for the Space Shuttle program.

  8. Evaluation of the seat fastening in the frame of a road bus submitted to frontal impact

    Directory of Open Access Journals (Sweden)

    Márcio Walber

    Full Text Available The collective intercity transportation by bus is currently a mean of locomotion much sought after by people. Security in accidents is a very important factor that must be taken into account in design of bus body structure, being the evaluation of passenger safety of this type of vehicle is an important subject that should be checked, because in many accidents occur disconnection between seats and fastening members causing serious passengers injury, often fatal. This work aims at evaluation the behavior of frame fixing of seats of intercity bus bodies, submitted to the frontal impact situation in a rigid wall of 100% offset, through evaluation by finite element method (FEM. This study uses a numerical model corresponding to the body structure and chassis, developed through flexible beam elements, combining with shell elements for the structure of the seats and its fastening members, with the objective of not missing the essential aspects of the problem, allowing the solution with a reduced computational time. The numerical model of bus body and seat was impacted against a rigid wall at a speed of 8.89 m/s, being its validation according to the deceleration curve established by Regulation 80. Then it was gotten the Von Mises stress in fastening members of the seat structure in bus body. It is also presented a proposal to improve the fastening of the seat structure, comparing the results of the stress gotten in the two types fastening submitted to the frontal impact.

  9. Research Paper: Impact of Air Seat Cushions and Ball Chairs on Classroom Behavior of Students with Autism Spectrum Disorder

    Directory of Open Access Journals (Sweden)

    Nader Matin Sadr

    2016-07-01

    Conclusion In the present study, therapy balls and or cushioned chairs for ASD students facilitated in-seat and on-task behaviors and improved classroom performance. It seems that using these alternative seating chairs can satisfy the subjects’ needs to sensory stimuli, and therefore, decreases their sensory seeking behaviors which interferes with their academic achievements. While, using therapy ball chairs for these students may facilitate in-seat behavior and decrease autistic behavior in class, the student’s response to dynamic seating is different individually. Therefore, chair selection must be based on vestibular reaction of the students.

  10. Best seating condition in children with spastic cerebral palsy : One type does not fit all

    NARCIS (Netherlands)

    Angsupaisal, Mattana; Dijkstra, Linze-Jaap; la Bastide-van Gemert, Sacha; van Hoorn, Jessika F.; Burger, Karine; Maathuis, Carel G. B.; Hadders-Algra, Mijna

    2017-01-01

    Background: The effect of forward-tilting of the seat surface and foot-support in children with spastic cerebral palsy (CP) is debated. Aim: To assess the effect of forward-tilting of the seat surface and foot-support in children with CP on kinematic head stability and reaching. Methods: Nineteen

  11. Design and optimization of a large flow rate booster pump in SWRO energy recovery system

    International Nuclear Information System (INIS)

    Lai, Z N; Wu, P; Wu, D Z; Wang, L Q

    2013-01-01

    Seawater reverse osmosis (SWRO) is a high energy-consumption industry, so energy efficiency is an important issue. Energy recovery systems, which contain a pressure exchanger and a booster pump, are widely used in SWRO plants. As a key part of energy recovery system, the difficulty of designing booster pumps lies in high inlet pressure, high medium causticity and large flow rate. High inlet pressure adds difficulties to seal design, and large flow rate and high efficiency requirement bring high demand for hydraulic design. In this paper, a 625 m 3 /h booster pump is designed and optimized according to the CFD (Computational Fluid Dynamics) simulation results. The impeller and volute is well designed, a new type of high pressure mechanical seal is applied and axial force is well balanced. After optimization based on blade redesign, the efficiency of the pump was improved. The best efficiency reaches more than 85% at design point according to the CFD simulation result

  12. Design and optimization of a large flow rate booster pump in SWRO energy recovery system

    Science.gov (United States)

    Lai, Z. N.; Wu, P.; Wu, D. Z.; Wang, L. Q.

    2013-12-01

    Seawater reverse osmosis (SWRO) is a high energy-consumption industry, so energy efficiency is an important issue. Energy recovery systems, which contain a pressure exchanger and a booster pump, are widely used in SWRO plants. As a key part of energy recovery system, the difficulty of designing booster pumps lies in high inlet pressure, high medium causticity and large flow rate. High inlet pressure adds difficulties to seal design, and large flow rate and high efficiency requirement bring high demand for hydraulic design. In this paper, a 625 m3/h booster pump is designed and optimized according to the CFD (Computational Fluid Dynamics) simulation results. The impeller and volute is well designed, a new type of high pressure mechanical seal is applied and axial force is well balanced. After optimization based on blade redesign, the efficiency of the pump was improved. The best efficiency reaches more than 85% at design point according to the CFD simulation result.

  13. Non-Invasive Detection of Respiration and Heart Rate with a Vehicle Seat Sensor.

    Science.gov (United States)

    Wusk, Grace; Gabler, Hampton

    2018-05-08

    This study demonstrates the feasibility of using a seat sensor designed for occupant classification from a production passenger vehicle to measure an occupant’s respiration rate (RR) and heart rate (HR) in a laboratory setting. Relaying occupant vital signs after a crash could improve emergency response by adding a direct measure of the occupant state to an Advanced Automatic Collision Notification (AACN) system. Data was collected from eleven participants with body weights ranging from 42 to 91 kg using a Ford Mustang passenger seat and seat sensor. Using a ballistocardiography (BCG) approach, the data was processed by time domain filtering and frequency domain analysis using the fast Fourier transform to yield RR and HR in a 1-min sliding window. Resting rates over the 30-min data collection and continuous RR and HR signals were compared to laboratory physiological instruments using the Bland-Altman approach. Differences between the seat sensor and reference sensor were within 5 breaths per minute for resting RR and within 15 beats per minute for resting HR. The time series comparisons for RR and HR were promising with the frequency analysis technique outperforming the peak detection technique. However, future work is necessary for more accurate and reliable real-time monitoring of RR and HR outside the laboratory setting.

  14. Searching the seat of the soul in Ancient Greek and Byzantine medical literature.

    Science.gov (United States)

    Lykouras, Eleftherios; Poulakou-Rebelakou, Effie; Ploumpidis, Demetrios N

    2010-12-01

    The objective of this paper was to examine the ancient and medieval concepts about the seat of the mental functions, as exposed in Greek texts from Antiquity to Byzantine times. The review of the philosophical and medical literature from the original ancient Greek language from the Homeric epics to the Holy Fathers of Christianity, as the problem of the seat of the soul remained without a certain answer through the centuries. Primitive concepts attributed great significance to the soul and dictated cannibal behaviours for the possession and eating of the defeated enemy's heart. Mental functions, such as thinking, feeling and mainly those related to affective manifestations, were attributed to the heart and to some other internal organs (liver, diaphragm) from the times of Greek mythology. Philosophy and empirical medicine had underestimated the brain probably because it is a 'silent' organ, contrary to the palpitating heart, with its obvious participations in the emotional reactions. The role of the brain as the mental organ and the seat of emotions has been gradually recognized. The permanent question of the seat of the soul had been for many centuries a critical dispute and the contribution of Greek philosophical and medical thought was decisive for the contemporary transformation of the whole concept.

  15. Who Sits Where? Infrastructure-Free In-Vehicle Cooperative Positioning via Smartphones

    Directory of Open Access Journals (Sweden)

    Zongjian He

    2014-06-01

    Full Text Available Seat-level positioning of a smartphone in a vehicle can provide a fine-grained context for many interesting in-vehicle applications, including driver distraction prevention, driving behavior estimation, in-vehicle services customization, etc. However, most of the existing work on in-vehicle positioning relies on special infrastructures, such as the stereo, cigarette lighter adapter or OBD (on-board diagnostic adapter. In this work, we propose iLoc, an infrastructure-free, in-vehicle, cooperative positioning system via smartphones. iLoc does not require any extra devices and uses only embedded sensors in smartphones to determine the phones’ seat-level locations in a car. In iLoc, in-vehicle smartphones automatically collect data during certain kinds of events and cooperatively determine the relative left/right and front/back locations. In addition, iLoc is tolerant to noisy data and possible sensor errors. We evaluate the performance of iLoc using experiments conducted in real driving scenarios. Results show that the positioning accuracy can reach 90% in the majority of cases and around 70% even in the worst-cases.

  16. Project of Ariane 5 LV family advancement by use of reusable fly-back boosters (named “Bargouzine”)

    Science.gov (United States)

    Sumin, Yu.; Bonnal, Ch.; Kostromin, S.; Panichkin, N.

    2007-12-01

    The paper concerns possible concept variants of a partially reusable Heavy-Lift Launch Vehicle derived from the advanced basic launcher (Ariane-2010) by means of substitution of the EAP Solid Rocket Boosters for a Reusable Starting Stage consisting two Liquid-propellant Reusable Fly-Back Boosters called "Bargouzin". This paper describes the status of the presently studied RFBB concepts during its three phases. The first project phase was dedicated to feasibility expertise of liquid-rocket reusable fly-back boosters ("Baikal" type) utilization for heavy-lift space launch vehicle. The design features and main conclusions are presented. The second phase has been performed with the purpose of selection of preferable concept among the alternative ones for the future Ariane LV modernization by using RFBB instead of EAP Boosters. The main requirements, logic of work, possible configuration and conclusion are presented. Initial aerodynamic, ballistic, thermoloading, dynamic loading, trade-off and comparison analysis have been performed on these concepts. The third phase consists in performing a more detailed expertise of the chosen LV concept. This part summarizes some of the more detailed results related to flight performance, system mass, thermoprotection system, aspects of technologies, ground complex modification, comparison analyses and conclusion.

  17. Does a booster intervention augment the preventive effects of an abbreviated version of the coping power program for aggressive children?

    Science.gov (United States)

    Lochman, John E; Baden, Rachel E; Boxmeyer, Caroline L; Powell, Nicole P; Qu, Lixin; Salekin, Karen L; Windle, Michel

    2014-01-01

    Booster interventions have been presumed to be important methods for maintaining the effects of evidence-based programs for children with behavioral problems, but there has been remarkably little empirical attention to this assumption. The present study examines the effect of a child-oriented booster preventive intervention with children who had previously received an abbreviated version (24 child sessions, 10 parent sessions) of the Coping Power targeted prevention program. Two hundred and forty-one children (152 boys, 89 girls) were screened as having moderate to high levels of aggressive behavior in 4th grade, then half were randomly assigned to receive the abbreviated Coping Power program in 5th grade, and half of the preventive intervention children were then randomly assigned to a Booster condition in 6th grade. The Booster sessions consisted of brief monthly individual contacts, and were primarily with the children. Five assessments across 4 years were collected from teachers, providing a three-year follow-up for all children who participated in the project. Results indicated that the abbreviated Coping Power program (one-third shorter than the full intervention) had long-term effects in reducing children's externalizing problem behaviors, proactive and reactive aggression, impulsivity traits and callous-unemotional traits. The Booster intervention did not augment these prevention effects. These findings indicate that a briefer and more readily disseminated form of an evidence-based targeted preventive intervention was effective. The findings have potential implications for policy and guidelines about possible intervention length and booster interventions.

  18. 75 FR 66064 - Extension of Application Period for Seats for the Stellwagen Bank National Marine Sanctuary...

    Science.gov (United States)

    2010-10-27

    ... Period for Seats for the Stellwagen Bank National Marine Sanctuary Advisory Council AGENCY: Office of National Marine Sanctuaries (ONMS), National Ocean Service (NOS), National Oceanic and Atmospheric... following vacant seats on the Stellwagen Bank National Marine Sanctuary Advisory Council: Advisory Council...

  19. 77 FR 27188 - Extension of Application Period for Seats for the Channel Islands National Marine Sanctuary...

    Science.gov (United States)

    2012-05-09

    ... Period for Seats for the Channel Islands National Marine Sanctuary Advisory Council AGENCY: Office of National Marine Sanctuaries (ONMS), National Ocean Service (NOS), National Oceanic and Atmospheric... following vacant seats on the Channel Islands National Marine Sanctuary Advisory Council: Chumash Community...

  20. 78 FR 5779 - Extension of Application Period for Seats for the Channel Islands National Marine Sanctuary...

    Science.gov (United States)

    2013-01-28

    ... Period for Seats for the Channel Islands National Marine Sanctuary Advisory Council AGENCY: Office of National Marine Sanctuaries (ONMS), National Ocean Service (NOS), National Oceanic and Atmospheric... following vacant seats on the Channel Islands National Marine Sanctuary Advisory Council: Business Alternate...

  1. 75 FR 57444 - Extension of Application Period for Seats for the Stellwagen Bank National Marine Sanctuary...

    Science.gov (United States)

    2010-09-21

    ... Period for Seats for the Stellwagen Bank National Marine Sanctuary Advisory Council AGENCY: Office of National Marine Sanctuaries (ONMS), National Ocean Service (NOS), National Oceanic and Atmospheric... following vacant seats on the Stellwagen Bank National Marine Sanctuary Advisory Council: Advisory Council...

  2. A Linac afterburner to supercharge the Fermilab booster

    International Nuclear Information System (INIS)

    Ankenbrandt M, Charles email = popovic@fnal.gov

    2002-01-01

    A Linac Afterburner is proposed to raise the energy of the beam injected into the Femrilab Booster from 400 MeV to about 600 MeV, thereby alleviating the longitudinal and transverse space-charge effects at low energy that currently limit its performance. The primary motivation is to increase the integrated luminosity of the Tevatron Collider in Run II, but other future programs would also recap substantial benefits. The estimated cost is $23M

  3. Detecting MOV stem to stem-nut lubricant degradation by reviewing MOV {open_quotes}seating time{close_quotes}

    Energy Technology Data Exchange (ETDEWEB)

    Loweth, W.A.

    1996-12-01

    The objective is to describe a methodology, suitable for IST Programs, that obtains sufficient data to assess and trend the overall condition of AC and DC MOVs. Using existing diagnostic test equipment, recording the time from Hard Seat Contact to the Torque Switch Trip point (TST), {open_quote}Seating Time (msec){close_quotes}, can provide a means to quickly detect for signs of lubricant degradation in the interface between the stem and stem-nut for MOVs. Obtaining and trending the {open_quote}Seating Time{close_quote} parameter can be easily accomplished using the sensors which provide motor current, torque or thrust. From the initial baseline test to subsequent tests, it is the change in time between Hard Seat Contact to Torque Switch Trip point that is utilized to monitor changes in the coefficient of friction between the stem and stem-nut. While many Licensees have begun their MOV Periodic Verification Programs, obtaining the {open_quotes}Seating Time{close_quotes} during Refueling Outages and comparing the results from subsequent outages can be an input to the justification for changing the MOV baseline test frequency.

  4. Analysis of WBV on standing and seated passengers during off-peak operation in KL monorail

    Science.gov (United States)

    Hasnan, K.; Bakhsh, Q.; Ahmed, A.; Ali, D.; Jamali, A. R.

    2018-03-01

    In this study, the Whole-Body Vibration (WBV) was analyzed on the standing and seated passenger during off-peak operating hours when train was on the track. The experiments were conducted on two car train at one constant location (bogie-1, which is near to driver’s cabin) during downward direction from KL sentral station towards Titiwangsa station. The aim of this study was to analyze that, in which posture of passenger’s exposures the maximum level of WBV. Since, one passenger was performed the whole journey in standing posture whereas, the other passenger was in seated posture. The result obtained from experiments for the RMS accelerations (Arms), maximum acceleration (Amax) and minimum acceleration (Amin) during the trip. As per standard ISO 2631-1, the daily vibration exposure (A8), Vibration Dose value (VDV) and Crest Factor (CF) of this trip for both standing and sitting orientations were calculated. Results shows that the seated passenger was exposed to longer periods of continuous vibration as compared to the standing passenger. Whereas, the Vibration Dose value (VDV) value was greater than the action value as per ISO 2631-1 and within the limit values. The study concluded that whole body vibration transmitted towards both passengers either standing or seated during their journey. But in overall results comparison of both orientations, the seated passengers gained higher vibration than the standing one.

  5. Numerical model for thermoeconomic diagnosis in commercial transcritical/subcritical booster refrigeration systems

    International Nuclear Information System (INIS)

    Ommen, Torben; Elmegaard, Brian

    2012-01-01

    Highlights: ► A transcritical booster refrigeration plant is modelled. ► We examine changes in cost flow at different operation parameters. ► The use of characteristic curves for diagnosis is studied. - Abstract: Transcritical/subcritical booster refrigeration systems are increasingly installed and used in Danish supermarkets. The systems operate in both transcritical and subcritical conditions dependent on the heat rejection performance and the ambient conditions. The plant consists of one refrigerant cycle supplying refrigerant for evaporators in both chilled and frozen display cases. In the paper, thermoeconomic theory is used to establish the cost of cooling at each individual temperature level based on operating costs. With a high amount of operating systems, faulty operation becomes an economic, and environmental, interest. A general solution for evaluation of these systems is considered, with the objective to reduce cost and power consumption of malfunctioning equipment in operation. An analysis of the use of thermoeconomic diagnosis methods is required, as these methods may prove applicable. To accommodate the analysis, a numerical model of a transcritical booster refrigeration plant is considered in this paper. Additionally the characteristic curves method is applied to the high pressure compressor unit of the refrigeration plant. The approach successfully determine whether an anomaly is intrinsic or induced in the component when no uncertainties are introduced in the steady state model.

  6. Looking forward: In-vehicle auxiliary display positioning affects carsickness.

    Science.gov (United States)

    Kuiper, Ouren X; Bos, Jelte E; Diels, Cyriel

    2018-04-01

    Carsickness is associated with a mismatch between actual and anticipated sensory signals. Occupants of automated vehicles, especially when using a display, are at higher risk of becoming carsick than drivers of conventional vehicles. This study aimed to evaluate the impact of positioning of in-vehicle displays, and subsequent available peripheral vision, on carsickness of passengers. We hypothesized that increased peripheral vision during display use would reduce carsickness. Seated in the front passenger seat 18 participants were driven a 15-min long slalom on two occasions while performing a continuous visual search-task. The display was positioned either at 1) eye-height in front of the windscreen, allowing peripheral view on the outside world, and 2) the height of the glove compartment, allowing only limited view on the outside world. Motion sickness was reported at 1-min intervals. Using a display at windscreen height resulted in less carsickness compared to a display at glove compartment height. Copyright © 2017 Elsevier Ltd. All rights reserved.

  7. The PS Booster's ejection kicker: full house.

    CERN Multimedia

    CERN PhotoLab

    1971-01-01

    The modules of the Booster's four-storied full-aperture kicker pretty much fill their vacuum tank (front cover removed). In the original 800 MeV version, the delay-type modules were pulsed at 30 kV from a Pulse-Forming-Network (PFN), yielding a field risetime as short as 60 ns. The fieldstrength was 0.1 T at a current of 1200 A. The modules are made from steel plates and ferrite slabs. The ferrite's high initial outgassing rate presented a serious vacuum problem for a long time.

  8. Comparison of the Effects of Seated, Supine, and Walking Interset Rest Strategies on Work Rate.

    Science.gov (United States)

    Ouellette, Kristen A; Brusseau, Timothy A; Davidson, Lance E; Ford, Candus N; Hatfield, Disa L; Shaw, Janet M; Eisenman, Patricia A

    2016-12-01

    Ouellette, KA, Brusseau, TA, Davidson, LE, Ford, CN, Hatfield, DL, Shaw, JM, and Eisenman, PA. Comparison of the effects of seated, supine, and walking interset rest strategies on work rate. J Strength Cond Res 30(12): 3396-3404, 2016-The idea that an upright posture should be maintained during the interset rest periods of training sessions is pervasive. The primary aim of this study was to determine differences in work rate associated with 3 interset rest strategies. Male and female members of the CrossFit community (male n = 5, female n = 10) were recruited to perform a strenuous training session designed to enhance work capacity that involved both cardiovascular and muscular endurance exercises. The training session was repeated on 3 separate occasions to evaluate 3 interset rest strategies, which included lying supine on the floor, sitting on a flat bench, and walking on a treadmill (0.67 m·s). Work rate was calculated for each training session by summing session joules of work and dividing by the time to complete the training session (joules of work per second). Data were also collected during the interset rest periods (heart rate [HR], respiratory rate [RR], and volume of oxygen consumed) and were used to explain why one rest strategy may positively impact work rate compared with another. Statistical analyses revealed significant differences (p ≤ 0.05) between the passive and active rest strategies, with the passive strategies allowing for improved work rate (supine = 62.77 ± 7.32, seated = 63.66 ± 8.37, and walking = 60.61 ± 6.42 average joules of work per second). Results also suggest that the passive strategies resulted in superior HR, RR, and oxygen consumption recovery. In conclusion, work rate and physiological recovery were enhanced when supine and seated interset rest strategies were used compared with walking interset rest.

  9. Reduced energy and volume air pump for a seat cushion

    Energy Technology Data Exchange (ETDEWEB)

    Vaughn, M.R.; Constantineau, E.J.; Groves, G.E.

    1997-08-19

    An efficient pump system is described for transferring air between sets of bladders in a cushion. The pump system utilizes a reversible piston within a cylinder in conjunction with an equalizing valve in the piston which opens when the piston reaches the end of travel in one direction. The weight of a seated user then forces air back across the piston from an inflated bladder to the previously deflated bladder until the pressure is equalized. In this fashion the work done by the pump is cut in half. The inflation and deflation of the different bladders is controlled to vary the pressure on the several pressure points of a seated user. A principal application is for wheel chair use to prevent pressure ulcers. 12 figs.

  10. Reduced energy and volume air pump for a seat cushion

    Energy Technology Data Exchange (ETDEWEB)

    Vaughn, Mark R. (Albuquerque, NM); Constantineau, Edward J. (Albuquerque, NM); Groves, Gordon E. (Tijeras, NM)

    1997-01-01

    An efficient pump system for transferring air between sets of bladders in a cushion. The pump system utilizes a reversible piston within a cylinder in conjunction with an equalizing valve in the piston which opens when the piston reaches the end of travel in one direction. The weight of a seated user then forces air back across the piston from an inflated bladder to the previously deflated bladder until the pressure is equalized. In this fashion the work done by the pump is cut in half. The inflation and deflation of the different bladders is controlled to vary the pressure on the several pressure points of a seated user. A principal application is for wheel chair use to prevent pressure ulcers.

  11. Multipole stack for the 4 rings of the PS Booster

    CERN Multimedia

    CERN PhotoLab

    1976-01-01

    The PS Booster (originally 800 MeV, now 1.4 GeV) saw first beam in 1972, routine operation began in 1973. The strive for ever higher intensities required the addition of multipoles. Manufacture of 8 stacks of multipoles was launched in 1974, for installation in 1976. For details, see 7511120X.

  12. Rural and Urban Differences in Passenger-Vehicle-Occupant Deaths and Seat Belt Use Among Adults - United States, 2014.

    Science.gov (United States)

    Beck, Laurie F; Downs, Jonathan; Stevens, Mark R; Sauber-Schatz, Erin K

    2017-09-22

    Motor-vehicle crashes are a leading cause of death in the United States. Compared with urban residents, rural residents are at an increased risk for death from crashes and are less likely to wear seat belts. These differences have not been well described by levels of rurality. 2014. Data from the Fatality Analysis Reporting System (FARS) and the Behavioral Risk Factor Surveillance System (BRFSS) were used to identify passenger-vehicle-occupant deaths from motor-vehicle crashes and estimate the prevalence of seat belt use. FARS, a census of U.S. motor-vehicle crashes involving one or more deaths, was used to identify passenger-vehicle-occupant deaths among adults aged ≥18 years. Passenger-vehicle occupants were defined as persons driving or riding in passenger cars, light trucks, vans, or sport utility vehicles. Death rates per 100,000 population, age-adjusted to the 2000 U.S. standard population and the proportion of occupants who were unrestrained at the time of the fatal crash, were calculated. BRFSS, an annual, state-based, random-digit-dialed telephone survey of the noninstitutionalized U.S. civilian population aged ≥18 years, was used to estimate prevalence of seat belt use. FARS and BRFSS data were analyzed by a six-level rural-urban designation, based on the U.S. Department of Agriculture 2013 rural-urban continuum codes, and stratified by census region and type of state seat belt enforcement law (primary or secondary). Within each census region, age-adjusted passenger-vehicle-occupant death rates per 100,000 population increased with increasing rurality, from the most urban to the most rural counties: South, 6.8 to 29.2; Midwest, 5.3 to 25.8; West, 3.9 to 40.0; and Northeast, 3.5 to 10.8. (For the Northeast, data for the most rural counties were not reported because of suppression criteria; comparison is for the most urban to the second-most rural counties.) Similarly, the proportion of occupants who were unrestrained at the time of the fatal crash

  13. RF field control for KAON Factory booster cavities

    International Nuclear Information System (INIS)

    Craig, S.T.; de Jong, M.S.

    1990-11-01

    A conceptual design is developed for control of the KAON Factory Booster rf accelerating fields. This design addresses control of cavity: tuning, voltage amplitude, and voltage phase angle. Time-domain simulations were developed to evaluated the proposed controllers. These simulations indicated that adequate tuning performance can be obtained with the combination of adaptive feed-forward and proportional feedback control. Voltage amplitude and voltage phase can be adequately controlled using non-adaptive feedforward and proportional feedback control

  14. Oil Stiction in Fast Switching Annular Seat Valves for Digital Displacement Fluid Power Machines

    DEFF Research Database (Denmark)

    Roemer, Daniel Beck; Johansen, Per; Pedersen, Henrik C.

    2014-01-01

    Digital Displacement (DD) fluid power machines utilizes electronically controlled seat valves connected to pressure chambers to obtain variable displacement with high operational efficiency and high bandwidth. To achieve high efficiency, fast valve switching is essential and all aspects related...... to the dynamic behaviour of the seat valves must be considered to optimize the machine efficiency. A significant effect influencing the valves switching performance is the presence of oil stiction when separating the contact surfaces in valve opening movement. This oil stiction force is limited by cavitation...... for low pressure levels, e.g. valves connected to the low pressure manifold, however for valves operated at higher pressure levels, the oil stiction force is dominating when the separating surfaces are close to contact. This paper presents an analytic solution to the oil stiction force for annular seat...

  15. Microenvironment temperature prediction between body and seat interface using autoregressive data-driven model.

    Science.gov (United States)

    Liu, Zhuofu; Wang, Lin; Luo, Zhongming; Heusch, Andrew I; Cascioli, Vincenzo; McCarthy, Peter W

    2015-11-01

    There is a need to develop a greater understanding of temperature at the skin-seat interface during prolonged seating from the perspectives of both industrial design (comfort/discomfort) and medical care (skin ulcer formation). Here we test the concept of predicting temperature at the seat surface and skin interface during prolonged sitting (such as required from wheelchair users). As caregivers are usually busy, such a method would give them warning ahead of a problem. This paper describes a data-driven model capable of predicting thermal changes and thus having the potential to provide an early warning (15- to 25-min ahead prediction) of an impending temperature that may increase the risk for potential skin damages for those subject to enforced sitting and who have little or no sensory feedback from this area. Initially, the oscillations of the original signal are suppressed using the reconstruction strategy of empirical mode decomposition (EMD). Consequentially, the autoregressive data-driven model can be used to predict future thermal trends based on a shorter period of acquisition, which reduces the possibility of introducing human errors and artefacts associated with longer duration "enforced" sitting by volunteers. In this study, the method had a maximum predictive error of body insensitivity and disability requiring them to be immobile in seats for prolonged periods. Copyright © 2015 Tissue Viability Society. Published by Elsevier Ltd. All rights reserved.

  16. Increased Seat Dump Angle in a Manual Wheelchair Is Associated With Changes in Thoracolumbar Lordosis and Scapular Kinematics During Propulsion.

    Science.gov (United States)

    Cloud, Beth A; Zhao, Kristin D; Ellingson, Arin M; Nassr, Ahmad; Windebank, Anthony J; An, Kai-Nan

    2017-10-01

    To quantify and compare spinal curvature and shoulder kinematics throughout the manual wheelchair (MWC) propulsion cycle for individuals with spinal cord injury (SCI) who were seated at 2 different seat dump angles. Single-group, repeated-measures study. Academic medical center. Individuals (N=28) with SCI or spinal cord disease who used MWCs completed a telephone screening, and 21 of them were eligible and completed the study. Participants' personal MWCs were modified to have seat dump angles of 0° or 14°, with a vertical backrest. Participants completed at least 3 propulsion cycles in each condition, during which spine and shoulder motion data were collected with fiberoptic and electromagnetic sensors, respectively. Thoracolumbar spinal curvature, glenohumeral kinematics, and scapulothoracic kinematics at the start of push (SP), mid-push (MP), end of push (EP), and mid-recovery. Participants had significantly less lordosis in the 14° condition for all propulsion events. Median differences ranged from 2.0° to 4.6°. Lordosis differences were more pronounced in those with low SCI. Scapulothoracic internal rotation was increased in the 14° condition at SP and MP (mean differences, 2.5° and 2.7°, respectively). Relative downward rotation increased in the 14° condition at SP and MP (mean differences, 2.4° and 2.1°, respectively). Scapulothoracic differences were more pronounced in those with high SCI. No glenohumeral rotations were significantly different between the conditions. Scapulothoracic kinematics and spinal curvature differences during propulsion may be associated with the position of other body segments or postural stability. Because no differences were observed at the glenohumeral joint, the risk of subacromial impingement may not be affected by this seat angle change. Copyright © 2017 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

  17. Beam Diagnosis and Lattice Modeling of the Fermilab Booster

    International Nuclear Information System (INIS)

    Huang, Xiaobiao

    2005-01-01

    A realistic lattice model is a fundamental basis for the operation of a synchrotron. In this study various beam-based measurements, including orbit response matrix (ORM) and BPM turn-by-turn data are used to verify and calibrate the lattice model of the Fermilab Booster. In the ORM study, despite the strong correlation between the gradient parameters of adjacent magnets which prevents a full determination of the model parameters, an equivalent lattice model is obtained by imposing appropriate constraints. The fitted gradient errors of the focusing magnets are within the design tolerance and the results point to the orbit offsets in the sextupole field as the source of gradient errors. A new method, the independent component analysis (ICA) is introduced to analyze multiple BPM turn-by-turn data taken simultaneously around a synchrotron. This method makes use of the redundancy of the data and the time correlation of the source signals to isolate various components, such as betatron motion and synchrotron motion, from raw BPM data. By extracting clean coherent betatron motion from noisy data and separates out the betatron normal modes when there is linear coupling, the ICA method provides a convenient means to measure the beta functions and betatron phase advances. It also separates synchrotron motion from the BPM samples for dispersion function measurement. The ICA method has the capability to separate other perturbation signals and is robust over the contamination of bad BPMs. The application of the ICA method to the Booster has enabled the measurement of the linear lattice functions which are used to verify the existing lattice model. The transverse impedance and chromaticity are measured from turn-by-turn data using high precision tune measurements. Synchrotron motion is also observed in the BPM data. The emittance growth of the Booster is also studied by data taken with ion profile monitor (IPM). Sources of emittance growth are examined and an approach to cure

  18. Delineation of potential deep seated landslides in a watershed using environmental index

    Science.gov (United States)

    Lai, Siao Ying; Lin, Chao Yuan; Lin, Cheng Yu

    2016-04-01

    The extreme rainfall induced deep seated landslides cause more attentions recently. Extreme rainfall can accelerate soil moisture content and surface runoff in slopeland which usually results in severe headward erosion and slope failures in an upstream watershed. It's a crucial issue for disaster prevention to extract the sites of potential deep seated landslide dynamically. Landslide risk and scale in a watershed were well discussed in this study. Risk of landslide occurrence in a watershed can be calculated from the multiplication of hazard and vulnerability for a certain event. A synthesis indicator derived from the indices of inverted extreme rainfall, road development and inverted normalized difference vegetation index can be effectively used as vulnerability for a watershed before the event. Landslide scale estimated from the indices of soil depth, headward erosion, river concave and dip slope could be applied to locate the hotspots of deep seated landslide in a watershed. The events of Typhoon Morakot in 2009 and Soudelor in 2015 were also selected in this study to verify the delineation accuracy of the model for the references of related authorities.

  19. Effect of oral booster vaccination of rainbow trout against Yersinia ruckeri depends on type of primary immunization

    DEFF Research Database (Denmark)

    Jaafar, Rzgar M.; Al-Jubury, Azmi; Dalsgaard, Inger

    2017-01-01

    provided as dip (most effective), bath (less effective) or orally (least effective). Oral immunization may be used as booster after dip but applied as a single oral application it induced merely a slight and statistically non-significant response. It is noteworthy that primary oral immunization followed...... already primed by one of these vaccination methods. Oral vaccination of trout (administering vaccine in feed) is an even more convenient way of presenting antigen to the fish but the effect of an oral booster has not previously been described in detail. The present work describes to what extent protection...... by an oral booster vaccination showed a trend for an even weaker response. It should be investigated if continued exposure to a low antigen concentration - as performed by two oral immunizations - may induce tolerance to the pathogen and thereby leave the fish more vulnerable....

  20. Power flow control using quadrature boosters

    Science.gov (United States)

    Sadanandan, Sandeep N.

    A power system that can be controlled within security constraints would be an advantage to power planners and real-time operators. Controlling flows can lessen reliability issues such as thermal limit violations, power stability problems, and/or voltage stability conditions. Control of flows can also mitigate market issues by reducing congestion on some lines and rerouting power to less loaded lines or onto preferable paths. In the traditional control of power flows, phase shifters are often used. More advanced methods include using Flexible AC Transmission System (FACTS) Controllers. Some examples include Thyristor Controlled Series Capacitors, Synchronous Series Static Compensators, and Unified Power Flow Controllers. Quadrature Boosters (QBs) have similar structures to phase-shifters, but allow for higher voltage magnitude during real power flow control. In comparison with other FACTS controllers QBs are not as complex and not as expensive. The present study proposes to use QBs to control power flows on a power system. With the inclusion of QBs, real power flows can be controlled to desired scheduled values. In this thesis, the linearized power flow equations used for power flow analysis were modified for the control problem. This included modifying the Jacobian matrix, the power error vector, and calculating the voltage injected by the quadrature booster for the scheduled real power flow. Two scenarios were examined using the proposed power flow control method. First, the power flow in a line in a 5-bus system was modified with a QB using the method developed in this thesis. Simulation was carried out using Matlab. Second, the method was applied to a 30-bus system and then to a 118-bus system using several QBs. In all the cases, the calculated values of the QB voltages led to desired power flows in the designated line.