An evolutionary algorithm for port-of-entry security optimization considering sensor thresholds

International Nuclear Information System (INIS)

Concho, Ana Lisbeth; Ramirez-Marquez, Jose Emmanuel

2010-01-01

According to the US Customs and Border Protection (CBP), the number of offloaded ship cargo containers arriving at US seaports each year amounts to more than 11 million. The costs of locating an undetonated terrorist weapon at one US port, or even worst, the cost caused by a detonated weapon of mass destruction, would amount to billions of dollars. These costs do not yet account for the devastating consequences that it would cause in the ability to keep the supply chain operating and the sociological and psychological effects. As such, this paper is concerned with developing a container inspection strategy that minimizes the total cost of inspection while maintaining a user specified detection rate for 'suspicious' containers. In this respect and based on a general decision-tree model, this paper presents a holistic evolutionary algorithm for finding the following: (1) optimal threshold values for every sensor and (2) the optimal configuration of the inspection strategy. The algorithm is under the assumption that different sensors with different reliability and cost characteristics can be used. Testing and experimentation show the proposed approach consistently finds high quality solutions in a reduced computational time.

One-Port Electronic Detection Strategies for Improving Sensitivity in Piezoelectric Resonant Sensor Measurements

Directory of Open Access Journals (Sweden)

Zhongxu Hu

2016-10-01

Full Text Available This paper describes a one-port mechanical resonance detection scheme utilized on a piezoelectric thin film driven silicon circular diaphragm resonator and discusses the limitations to such an approach in degenerate mode mass detection sensors. The sensor utilizes degenerated vibration modes of a radial symmetrical microstructure thereby providing both a sense and reference mode allowing for minimization of environmental effects on performance. The circular diaphragm resonator was fabricated with thickness of 4.5 µm and diameter of 140 µm. A PZT thin film of 0.75 µm was patterned on the top surface for the purposes of excitation and vibration sensing. The device showed a resonant frequency of 5.8 MHz for the (1, 1 mode. An electronic interface circuit was designed to cancel out the large static and parasitic capacitance allowing for electrical detection of the mechanical vibration thereby enabling the frequency split between the sense and reference mode to be measured accurately. The extracted motional current, proportional to the vibration velocity, was fed back to the drive to effectively increase the Q factor, and therefore device sensitivity, by more than a factor of 8. A software phase-locked loop was implemented to automatically track the resonant frequencies to allow for faster and accurate resonance detection. Results showed that by utilizing the absolute mode frequencies as an indication of sensor temperature, the variation in sensor temperature due to the heating from the drive electronics was accounted for and led to an ultimate measurement sensitivity of 2.3 Hz.

One-Port Electronic Detection Strategies for Improving Sensitivity in Piezoelectric Resonant Sensor Measurements

Science.gov (United States)

Hu, Zhongxu; Hedley, John; Keegan, Neil; Spoors, Julia; Gallacher, Barry; McNeil, Calum

2016-01-01

This paper describes a one-port mechanical resonance detection scheme utilized on a piezoelectric thin film driven silicon circular diaphragm resonator and discusses the limitations to such an approach in degenerate mode mass detection sensors. The sensor utilizes degenerated vibration modes of a radial symmetrical microstructure thereby providing both a sense and reference mode allowing for minimization of environmental effects on performance. The circular diaphragm resonator was fabricated with thickness of 4.5 µm and diameter of 140 µm. A PZT thin film of 0.75 µm was patterned on the top surface for the purposes of excitation and vibration sensing. The device showed a resonant frequency of 5.8 MHz for the (1, 1) mode. An electronic interface circuit was designed to cancel out the large static and parasitic capacitance allowing for electrical detection of the mechanical vibration thereby enabling the frequency split between the sense and reference mode to be measured accurately. The extracted motional current, proportional to the vibration velocity, was fed back to the drive to effectively increase the Q factor, and therefore device sensitivity, by more than a factor of 8. A software phase-locked loop was implemented to automatically track the resonant frequencies to allow for faster and accurate resonance detection. Results showed that by utilizing the absolute mode frequencies as an indication of sensor temperature, the variation in sensor temperature due to the heating from the drive electronics was accounted for and led to an ultimate measurement sensitivity of 2.3 Hz. PMID:27792154

ALC Rooftop Sensor System

Science.gov (United States)

2017-10-31

Department of the Army position unless so designated by other authorized documents. Citation of manufacturer’s or trade names does not constitute an... Interior view of the new sensor box ...................................................... 3 Fig. 4 Interior of original sensor box...7 Fig. 10 Interior of fiber patch panel .................................................................. 7 Fig. 11

Extreme Wave-Induced Oscillation in Paradip Port Under the Resonance Conditions

Science.gov (United States)

Kumar, Prashant; Gulshan

2017-12-01

A mathematical model is constructed to analyze the long wave-induced oscillation in Paradip Port, Odisha, India under the resonance conditions to avert any extreme wave hazards. Boundary element method (BEM) with corner contribution is utilized to solve the Helmholtz equation under the partial reflection boundary conditions. Furthermore, convergence analysis is also performed for the boundary element scheme with uniform and non-uniform discretization of the boundary. The numerical scheme is also validated with analytic approximation and existing studies based on harbor resonance. Then, the amplification factor is estimated at six key record stations in the Paradip Port with multidirectional incident waves and resonance modes are also estimated at the boundary of the port. Ocean surface wave field is predicted in the interior of Paradip Port for the different directional incident wave at various resonance modes. Moreover, the safe locations in the port have been identified for loading and unloading of moored ship with different resonance modes and directional incident waves.

An integrated port camera and display system for laparoscopy.

Science.gov (United States)

Terry, Benjamin S; Ruppert, Austin D; Steinhaus, Kristen R; Schoen, Jonathan A; Rentschler, Mark E

2010-05-01

In this paper, we built and tested the port camera, a novel, inexpensive, portable, and battery-powered laparoscopic tool that integrates the components of a vision system with a cannula port. This new device 1) minimizes the invasiveness of laparoscopic surgery by combining a camera port and tool port; 2) reduces the cost of laparoscopic vision systems by integrating an inexpensive CMOS sensor and LED light source; and 3) enhances laparoscopic surgical procedures by mechanically coupling the camera, tool port, and liquid crystal display (LCD) screen to provide an on-patient visual display. The port camera video system was compared to two laparoscopic video systems: a standard resolution unit from Karl Storz (model 22220130) and a high definition unit from Stryker (model 1188HD). Brightness, contrast, hue, colorfulness, and sharpness were compared. The port camera video is superior to the Storz scope and approximately equivalent to the Stryker scope. An ex vivo study was conducted to measure the operative performance of the port camera. The results suggest that simulated tissue identification and biopsy acquisition with the port camera is as efficient as with a traditional laparoscopic system. The port camera was successfully used by a laparoscopic surgeon for exploratory surgery and liver biopsy during a porcine surgery, demonstrating initial surgical feasibility.

Smartphone audio port data collection cookbook

Directory of Open Access Journals (Sweden)

Kyle Forinash

2018-06-01

Full Text Available The audio port of a smartphone is designed to send and receive audio but can be harnessed for portable, economical, and accurate data collection from a variety of sources. While smartphones have internal sensors to measure a number of physical phenomena such as acceleration, magnetism and illumination levels, measurement of other phenomena such as voltage, external temperature, or accurate timing of moving objects are excluded. The audio port cannot be only employed to sense external phenomena. It has the additional advantage of timing precision; because audio is recorded or played at a controlled rate separated from other smartphone activities, timings based on audio can be highly accurate. The following outlines unpublished details of the audio port technical elements for data collection, a general data collection recipe and an example timing application for Android devices.

Strong Motion Instrumentation of Seismically-Strengthened Port Structures in California by CSMIP

Science.gov (United States)

Huang, M.J.; Shakal, A.F.

2009-01-01

The California Strong Motion Instrumentation Program (CSMIP) has instrumented five port structures. Instrumentation of two more port structures is underway and another one is in planning. Two of the port structures have been seismically strengthened. The primary goals of the strong motion instrumentation are to obtain strong earthquake shaking data for verifying seismic analysis procedures and strengthening schemes, and for post-earthquake evaluations of port structures. The wharves instrumented by CSMIP were recommended by the Strong Motion Instrumentation Advisory Committee, a committee of the California Seismic Safety Commission. Extensive instrumentation of a wharf is difficult and would be impossible without the cooperation of the owners and the involvement of the design engineers. The instrumentation plan for a wharf is developed through study of the retrofit plans of the wharf, and the strong-motion sensors are installed at locations where specific instrumentation objectives can be achieved and access is possible. Some sensor locations have to be planned during design; otherwise they are not possible to install after construction. This paper summarizes the two seismically-strengthened wharves and discusses the instrumentation schemes and objectives. ?? 2009 ASCE.

Three ports versus four ports laparoscopic cholecystectomy

International Nuclear Information System (INIS)

Shah, S.F.; Waqar, S.; Chaudry, M.A.; Hameed, S.

2017-01-01

To compare three ports laparoscopic cholecystectomy and four ports laparoscopic cholecystectomy in terms of complications, time taken to complete the procedure, hospital stay and cost effectiveness in local perspective. Methodology: This randomized control trial included 60 patients who underwent elective laparoscopic cholecystectomy at Department of Surgery, Pakistan Institute of Medical Sciences, Islamabad, Pakistan from January 2013 to June 2013. These patients were randomized on computer generated table of random numbers into group A and Group B. In Group A patients four ports were passed to perform laparoscopic cholecystectomy and in Group B patients three ports were passed to perform the procedure. Results: The mean age in both groups was 44 years (range 18-72). Three ports laparoscopic cholecystectomy (43 min) took less time to complete than four ports laparoscopic cholecystectomy (51 min). Patients in three ports laparoscopic cholecystectomy experienced less pain as compared to four ports group. The total additional analgesia requirement in 24 hours calculated in milligrams was less in three port laparoscopic cholecystectomy group as compared four port laparoscopic cholecystectomy group. The mean hospital stay in three port laparoscopic cholecystectomy group is 25 hours while the mean hospital stay in the four port laparoscopic cholecystectomy group is 28 hours. Conclusion: Three ports laparoscopic cholecystectomy is safe and effective procedure and it did not compromise the patient safety. (author)

Development of chipless, wireless current sensor system based on giant magnetoimpedance magnetic sensor and surface acoustic wave transponder.

Science.gov (United States)

Kondalkar, Vijay V; Li, Xiang; Park, Ikmo; Yang, Sang Sik; Lee, Keekeun

2018-02-05

A chipless, wireless current sensor system was developed using a giant magnetoimpedance (GMI) magnetic sensor and one-port surface acoustic wave (SAW) reflective delay line for real-time power monitoring in a current-carrying conductor. The GMI sensor has a high-quality crystalline structure in each layer, which contributes to a high sensitivity and good linearity in a magnetic field of 3-16 Oe. A 400 MHz RF energy generated from the interdigital transducer (IDT)-type reflector on the one-port SAW delay line was used as an activation source for the GMI magnetic sensor. The one-port SAW delay line replaces the presently existing transceiver system, which is composed of thousands of transistors, thus enabling chipless and wireless operation. We confirmed a large variation in the amplitude of the SAW reflection peak with a change in the impedance of the GMI sensor caused by the current flow through the conductor. Good linearity and sensitivity of ~0.691 dB/A were observed for currents in the range 1-12 A. Coupling of Mode (COM) modeling and impedance matching analysis were also performed to predict the device performance in advance and these were compared with the experimental results.

Ports Primer: 3.2 Port Governance

Science.gov (United States)

State and local governments are important players in port governance and in oversight of transportation projects that may affect ports. Private corporations may also play a role if they lease or own a terminal at a port.

Evaluation of microwave cavity gas sensor for in-vessel monitoring of dry cask storage systems

Science.gov (United States)

Bakhtiari, S.; Gonnot, T.; Elmer, T.; Chien, H.-T.; Engel, D.; Koehl, E.; Heifetz, A.

2018-04-01

Results are reported of research activities conducted at Argonne to assess the viability of microwave resonant cavities for extended in-vessel monitoring of dry cask storage system (DCSS) environment. One of the gases of concern to long-term storage in canisters is water vapor, which appears due to evaporation of residual moisture from incompletely dried fuel assembly. Excess moisture could contribute to corrosion and deterioration of components inside the canister, which would in turn compromise maintenance and safe transportation of such systems. Selection of the sensor type in this work was based on a number of factors, including good sensitivity, fast response time, small form factor and ruggedness of the probing element. A critical design constraint was the capability to mount and operate the sensor using the existing canister penetrations-use of existing ports for thermocouple lances. Microwave resonant cavities operating at select resonant frequency matched to the rotational absorption line of the molecule of interest offer the possibility of highly sensitive detection. In this study, two prototype K-band microwave cylindrical cavities operating at TE01n resonant modes around the 22 GHz water absorption line were developed and tested. The sensors employ a single port for excitation and detection and a novel dual-loop inductive coupling for optimized excitation of the resonant modes. Measurement of the loaded and unloaded cavity quality factor was obtained from the S11 parameter. The acquisition and real-time analysis of data was implemented using software based tools developed for this purpose. The results indicate that the microwave humidity sensors developed in this work could be adapted to in-vessel monitoring applications that require few parts-per-million level of sensitivity. The microwave sensing method for detection of water vapor can potentially be extended to detection of radioactive fission gases leaking into the interior of the canister through

Cooperation Performance Evaluation between Seaport and Dry Port; Case of Qingdao Port and Xi'an Port

Directory of Open Access Journals (Sweden)

Jian Li

2014-12-01

Full Text Available Along with the drastic competition among ports, the strive for the vast economic hinterland and the supply of goods have become strategic problems for port operators. At the same time, port enterprises are paying more and more attention to the construction of dry ports. This article establishes the port cooperation performance evaluation index based on the balanced score card method and uses the grey relational degree method to evaluate the cooperation performance between seaports and dry ports. Finally using Qingdao port and Xi'an port as an example, and Zhengzhou port and Lanzhou port as benchmarks, the application of this evaluation method is introduced in detail. The conclusion reveals that cooperation between Qingdao port and Xi'an port has deficiencies in customer satisfaction, financial cooperation and non-market tools. Alongside this, the author proposes related issues about information management in the supply chain, competition position and the scope of hinterland. This article, combined with the related theory of supply chain and performance evaluation, puts forward a set of relatively complete cooperation performance evaluations between seaports and dry ports, which provide scientific theory support for better cooperation.

Sensor for metal detection

KAUST Repository

Kodzius, Rimantas

2014-06-26

NOVELTY - The sensor has a microfluidic flow channel that is provided with an inlet port, an outlet port, and a detection chamber. The detection chamber is provided with a group of sensing electrodes (4) having a working electrode (8), a counter electrode (9), and a reference electrode (10). A flow sensor is configured to measure flow in the channel. A temperature sensor (6) is configured to measure temperature in the channel (3). An electrical connection is configured to connect the sensor to a sensing device. USE - Sensor for detecting metal such as toxic metal in sample such as clinical sample such as stool, saliva, sputum, bronchial lavage, urine, vaginal swab, nasal swab, biopsy, tissue, tears, breath, blood, serum, plasma, cerebrospinal fluid, peritoneal fluid, pleural fluid, pericardial fluid, joint fluid, and amniotic fluid, water sample, food sample, air sample, and soil sample (all claimed). ADVANTAGE - The sensor for use with the portable analytical instrument is configured for detection of metalsin samples. The sensor can provide the excellent solution for on-site metal detection, including heavy metal detection. The sensors can provide significant advantages in higher throughput, lower cost, at the same time being less labor intensive and less dependent on individual skills. The disposable design of the sensor, the enhanced reliability and repeatability of measurements can be obtained. The sensors can be widely applied in various industries. DETAILED DESCRIPTION - INDEPENDENT CLAIMS are included for the following: (1) a system for detecting metal in sample; and (2) a method for using sensor for detecting metal in sample. DESCRIPTION OF DRAWING(S) - The drawing shows a schematic view of the sensor prototype. Channel (3) Sensing electrodes (4) Temperature sensor (6) Working electrode (8) Counter electrode (9) Reference electrode (10)

Intrusion detection sensors

International Nuclear Information System (INIS)

Williams, J.D.

1978-07-01

Intrusion detection sensors are an integral part of most physical security systems. Under the sponsorship of the U.S. Department of Energy, Office of Safeguards and Security, Sandia Laboratories has conducted a survey of available intrusion detection sensors and has tested a number of different sensors. An overview of these sensors is provided. This overview includes (1) the operating principles of each type of sensor, (2) unique sensor characteristics, (3) desired sensor improvements which must be considered in planning an intrusion detection system, and (4) the site characteristics which affect the performance of both exterior and interior sensors. Techniques which have been developed to evaluate various intrusion detection sensors are also discussed

Metropolitian area network services comprised of virtual local area networks running over hybrid fiber-coax and asynchronous transfer mode technologies

Science.gov (United States)

Biedron, William S.

1995-11-01

Since 1990 there has been a rapid increase in the demand for communication services, especially local and wide area network (LAN/WAN) oriented services. With the introduction of the DFB laser transmitter, hybrid-fiber-coax (HFC) cable plant designs, ATM transport technologies and rf modems, new LAN/WAN services can now be defined and marketed to residential and business customers over existing cable TV systems. The term metropolitan area network (MAN) can be used to describe this overall network. This paper discusses the technical components needed to provision these services as well as provides some perspectives on integration issues. Architecture at the headend and in the backbone is discussed, as well as specific service definitions and the technology issues associated with each. The TCP/IP protocol is suggested as a primary protocol to be used throughout the MAN.

Developing the port of Belawan as a modern and international port

Science.gov (United States)

Many, N.

2018-03-01

This study discusses the processes of government to pass the port development plan in Indonesia with the Port of Belawan and its port expansion as the study case. The study uses a descriptive approach by reviewing and analyzing some of relevant literature as the sources. It also reviews and examines the port development theoretical concepts and models giving attention to the international hub port models resulted from the previous studies. The international hub port aspects assessed to be further applied and compared to the actual situation of the Port of Belawan. This process draws the conclusion on which concept and model the port classified, followed by some recommendations concerning the necessary actions to be taken. The results show that: (1) The port planning regulated in port master plan is the guideline and foundation to implement the port development; (2) Spatial and zoning plan regulations are very important in the preparation, planning, and implementation of port development; (3) It has not provided the necessary facilities and criteria of the global hub port model has not been met completely. The port is strategic to be completely developed as the regional hub port to compete with the major ports of neighboring countries. Eventually, this study requires further analysis to examine the economic feasibility of the Port of Belawan in more comprehensive way functioning as an international hub port along with the ongoing development of Kuala Tanjung Port to achieve its ultimate objectives, among other things, the port effectiveness, efficiency, and competitiveness.

COMPARATIVE ANALYSIS OF LEADING PORTS OF LATVIA: COMPETITIVENESS OF LIEPAJA PORT

Directory of Open Access Journals (Sweden)

Diāna Līduma

2015-06-01

Full Text Available There are 10 operating ports in Latvia and 3 of them – Liepaja, Ventspils and Riga ports are regarded as the leading commercial ports. Role of port operation in the economics of region and country is essential from the point of view of employment and entrepreneurship. This is based with data on investment of operation of Latvian ports in GDP, on average it is assessed to be 5-7% annually. In the context of employment, Liepaja Port gives work to 6.9% of human resources of the city. However, concern about the competitiveness of Liepaja Port influenced by the proximity of more developed competitive ports, technical possibilities of the port and dynamics of freight turnover has occurred in recent years. Therewith in framework of this article in the context of such criteria as location of ports and their technical parameters, volumes of freight, specialization and costs of ports, the operation of leading ports of Latvia is intercompared and analyzed by clarifying whether Liepaja Port is competitive among other ports of Latvia. Opinions of port experts on perspectives of port development and statistical data of ports from 2011-2013 are analyzed within the framework of the article. The aim of the research is to clarify the comparative advantages of ports of Latvia. The research revealed that the provision of competitiveness of Liepaja Port is to be related with application of the available free territories, advantages of location in relation to the Scandinavian market, and the necessity to develop the cooperation among ports of Latvia to offer joint freight acquisition, distributions and unified logistics solution and strengthen the position of ports in the circumstances of international competition.

A wearable RF sensor on fabric substrate for pulmonary edema monitoring

KAUST Repository

Tayyab, Muhammad; Sharawi, Mohammad S.; Shamim, Atif

2017-01-01

We propose a radio frequency (RF) sensor built on a fabric textile substrate for pulmonary edema monitoring. The 37-port RF sensor is designed and optimized to operate at 60 MHz with a low input power of 1 mW. By applying the least squares (LS) method, an equation was obtained for dielectric constant estimation using the transmission coefficient of each RF sensor port. The simulated errors are estimated for normal lung, edema and emphysema infected lung cases using a human chest model with an average error of 0.57%. Inkjet printing of the proposed design is then discussed.

A wearable RF sensor on fabric substrate for pulmonary edema monitoring

KAUST Repository

Tayyab, Muhammad

2017-11-30

We propose a radio frequency (RF) sensor built on a fabric textile substrate for pulmonary edema monitoring. The 37-port RF sensor is designed and optimized to operate at 60 MHz with a low input power of 1 mW. By applying the least squares (LS) method, an equation was obtained for dielectric constant estimation using the transmission coefficient of each RF sensor port. The simulated errors are estimated for normal lung, edema and emphysema infected lung cases using a human chest model with an average error of 0.57%. Inkjet printing of the proposed design is then discussed.

Two-port access versus four-port access laparoscopic ovarian cystectomy.

Science.gov (United States)

Choi, Won-Kyu; Kim, Jang-Kew; Yang, Jung-Bo; Ko, Young-Bok; Nam, Sang-Lyun; Lee, Ki-Hwan

2014-09-01

This study was conducted to compare the surgical outcomes between two-port access and four-port access laparoscopic ovarian cystectomy. Four hundred and eighty nine patients who had received two-port access laparoscopic ovarian cystectomy (n=175) and four-port access laparoscopic ovarian cystectomy (n=314) in Chungnam National University Hospital from January 2009 to August 2012 were analyzed retrospectively. The data were compared between the bilaterality of the cysts and cyst diameter of less than 6 cm and 6 cm or more. There were no significant differences in patient's age, parity, body weight, body mass index and history of previous surgery between the two-port and four-port access laparoscopy group. Bilaterality of ovarian cysts was more in fourport access laparoscopy group (13.7% vs. 32.5%, P=0.000). There were no significant differences in operation time, hemoglobin change, hospital stay, adhesiolysis, transfusion, and insertion of hemo-vac between the two-port and four-port access laparoscopy group for size matched compare. However additional analgesics were more in four-port access laparoscopy group for unilateral ovarian cystectomy. Two-port access laparoscopic surgery was feasible and safe for unilateral and bilateral ovarian cystectomy compare with four-port access laparoscopic surgery.

Green Port / Eco Port Project - Applications and Procedures in Turkey

Science.gov (United States)

Akgul, Burak

2017-12-01

As being the heartlands of international trade, sea ports are the junction points of land and sea routes. The growth of global trade has led to the development of number and capacity as well as the service quality of ports. The policies and procedures applied during construction, operation and development of ports under development with environmental considerations scope has evolved in accordance with the needs of global trends. Although maritime transportation provides the most ecofriendly transportation method, the reduction of potential environmental threats and continuous improvement of ports and their vicinity is paramount from environmental concerns with regards to the international environmental standards. In the context of the study, national and international legal regulations governing the control of the environmental impacts of the activity groups causing pollution in Turkey based sea ports were viewed. In addition, the models applied during the measurement and documentation of environmental impacts were investigated. The most important aspects in terms of the effectiveness of the environmental management models are legal regulations. However, the standards applied at the ports without any legal obligation, such as EcoPorts applications, ISO 14001 standard, and the EMAS (Eco-Management and Audit Scheme) were sought in the scope of the study. The boundaries of the study were determined as the EU based Environmental Management Systems and the Green Port/Eco Port Project which is being administered by the Turkish Ministry of Transport, Maritime and Communication. “Marport”, which is Turkey’s first certified Green Port / Eco Port is designated as the experimental study site. In addition, the provisions in the ports of ESPO member countries are approached in order to compare the effectiveness and applicability of Green Port / Eco Port Project.

Rotary Speed Sensor for Antilocking Brakes

Science.gov (United States)

Berdahl, C. M.

1986-01-01

Sensor based on fluidic principles produces negative pressure approximately proportional to rotational speed. Sensor developed as part of antilocking brake system for motorcycles. Uses inlet pressure rather than outlet pressure as braking-control signal, eliminating pressure pulsations caused by pump vanes and ensuring low-noise signal. Sensor is centrifugal air pump turned by one of motorcycle wheels. Air enters pump through orifice plates, and suction taken off through port in pump inlet plenum.

Flat-port connectors

KAUST Repository

Alrashed, Mohammed

2017-05-26

Disclosed are various embodiments for connectors used with electronic devices, such as input and/or output ports to connect peripheral equipment or accessories. More specifically, various flat-port are provided that can be used in place of standard connectors including, but not limited to, audio jacks and Universal Serial Bus (USB) ports. The flat-port connectors are an alternate connection design to replace the traditional receptacle port (female-port), making the device more sealed creation more dust and water resistant. It is unique in the way of using the outer surfaces of the device for the electrical connection between the ports. Flat-port design can allow the manufacture of extremely thin devices by eliminating the side ports slots that take a lot of space and contribute to the increase thickness of the device. The flat-port receptacle improves the overall appearance of the device and makes it more resistant to dust and water.

Intra-arterial port implantation for intra-arterial chemotherapy : comparison between PIPS(Percutaneously Implantable Port System) and port system

International Nuclear Information System (INIS)

Yoon, Sang Jin; Shim, Hyung Jin; Jung, Hun Young; Choi, Yong Ho; Kim, Yang Soo; Song, In Sup; Kwak, Byung Kook

1999-01-01

To compare the techniques and complications of intra-arterial port implantation for intra-arterial chemotherapy between PIPS and the port system. For intra-arterial port implantation, 27 cases in 27 patients were retrospectively evaluated using PIPS(PIPS-200, William Cook Europe, Denmark) while for 21 cases in 19 patients a pediatric venous port system(Port-A-Cath, 5.8F, SIMS Deltec, U. S. A.) was used. All intra-arterial port implantation was performed percuteneously in an angiographic ward. Hepatocellular carcinoma was diagnosed in 18 patients and hepatic metastasis in 16. Peripheral cholangiocarcinoma, and pancreatic gastric, ovarian, renal cell and colon carcinoma were included. We compared the techniques and complications between PIPS and the port system. The follow up period ranged from 23 to 494(mean, 163) days in PIPS and from 12 to 431(mean, 150) days in the port system. In all cases, intra-arterial port implantations were technically successful. Port catheter tips were located in the common hepatic artery(n=8), proper hepatic artery(n=7), right hepatic artery(n=5), gastroduodenal artery(n=2), left hepatic artery(n=1), pancreaticoduodenal artery(n=1), inferior mesenteric artery(n=1), lumbar artery(n=1), and renal artery(n=1) in PIPS, and in the proper hepatic artery(n=6), gastroduodenal artery(n=6), common hepatic artery(n=3), right hepatic artery(n=4), inferior mesenteric artery(n=1), and internal iliac artery(n=1) in the port system. Port chambers were buried in infrainguinal subcutaneous tissue. Using PIPS, complications developed in seven cases(25.9%) and of these, four (57.1%) were catheter or chamber related. In the port system, catheter or chamber related complications developed in four cases(19.0%). Because PIPS and the port system have relative merits and demetrits, successful intra-arterial port implantation is possible if equipment is properly selected

Port Stakeholder Summit: Advancing More Sustainable Ports (April 2014)

Science.gov (United States)

EPA's National Port Stakeholders Summit, Advancing More Sustainable Ports, focused on actions to protect air quality while reducing climate risk and supporting economic growth, making ports more environmentally sustainable.

A subtractive approach to interior intrusion detection system design

International Nuclear Information System (INIS)

Sons, R.J.; Graham, R.H. Jr.

1986-01-01

This paper discusses the subtractive approach to interior intrusion detection system design which assumes that all sensors are viable candidates until they are subjected to the constraints imposed by a particular facility. The constraints are determined by a sequence of questions concerning parameters such as threat definition, facility description and operation, environment, assets to be protected, security system capabilities, and cost. As a result of the questioning, some sensors will be eliminated from the candidate list, and the ''best'' set of sensors for the facility will remain. This form of questioning could be incorporated into an expert system aiding future intrusion detection system designs

Ports Initiative

Science.gov (United States)

EPA's Ports Initiative works in collaboration with the port industry, communities, and government to improve environmental performance and increase economic prosperity. This effort helps people near ports breath cleaner air and live better lives.

An interior vessel viewing system for DIII-D

International Nuclear Information System (INIS)

Senior, R.

1989-11-01

It was anticipated that there could be damage to the interior walls of the vacuum vessel during operations of the DIII-D tokamak. A method of viewing the inside of the vessel from the outside was required, that would allow the interior walls to be inspected visually for damage and to locate any debris resulting from operations. A miniature closed circuit television color camera system was developed which could be inserted into one of several ports of the vessel during a 'clean' vent, i.e., vented to inert gas. The system has pan, tilt and zoom capability and carries its own lighting. The use of this system allows a quick assessment of the condition of the vessel to be made under 'clean' vent conditions. This precludes the need for the permit process and manned entry into the vessel which would allow air inside the vessel. A permanent record of the inspection can then be made on video tape. The design and configuration of this camera system is presented and its use as a diagnostic tool discussed. 2 refs., 5 figs

Revisiting port pricing : a proposal for seven port pricing principles

NARCIS (Netherlands)

Van Den Berg, R.; De Langen, P.W.; Van Zuijlen, P.C.J.

2017-01-01

A review of seven large landlord port authorities around the world reveals a notable diversity of pricing structures. While port authorities increasingly act as commercial undertakings, port pricing often seems to be not driven by commercial considerations. In this paper, we argue that ports can be

Influence of Port Policy on the Development of Croatian Container Ports

Directory of Open Access Journals (Sweden)

Čedomir Dundović

2002-03-01

Full Text Available It is important to consider the port development throughoutthe world from the aspect of economical, transport and portpolicy and their mutual impact on commerce and efficiency ofports. By examining such relations in the context of developmentof the Croatian container ports, it is possible to define reasonsfor lagging behind of Croatian ports compared to theworld movements.The main reason for the negative trend of development ofCroatian container ports lies in the non-existence of adequatemeasures of transport, maritime and port policy. Analysis ofstatistics over the past decade and comparison of structure andvolume of the general cargo traffic in the Rijeka port and theneighbouring ports in the area of North Adriatic are both showingsignificant size discrepancy and uncompetitiveness of theCroatian port. Disturbances that have brought to such a situationresult from inadequate port policy and non-harmonisedactivities between various modes of transport.In order to overcome such situation, the authors suggest determiningof clear tasks, goals and measures of the port policythat have to be undertaken so that the Croatian policy could becompatible with the main aspects, development tendencies andmeasures of theE U port policy.

Déficit nutricional em crianças de uma cidade de grande porte do interior da Bahia, Brasil

Directory of Open Access Journals (Sweden)

Gilmar Mercês de Jesus

2014-05-01

Full Text Available O estudo objetiva analisar o déficit nutricional de crianças de uma cidade de grande porte do interior da Bahia e os fatores socioambientais, características maternas e infantis associadas. Avaliou-se informações de duplas de mães e crianças de quatro anos, de uma coorte de nascidos vivos. O déficit nutricional foi definido pelo índice antropométrico estatura-para-idade (E/I, no ponto de corte -1 escore-z em relação à referência do Multicentre Growth Reference Study de 2006. As variáveis estudadas foram: características das crianças (peso ao nascer e gemelaridade e maternas (idade na ocasião do parto, nível de instrução, paridade e realização de pré-natal e fatores socioambientais (revestimento do piso e do teto domicílio, fonte da água consumida, canalização interna de água, água utilizada para o consumo e posse de geladeira. Utilizou-se a regressão logística para identificar os fatores associados ao déficit nutricional, o qual ocorreu em 24,6% das crianças. Peso insuficiente no nascimento, pré-natal inadequado, revestimento precário do piso do domicílio e ausência de canalização interna de água foram preditores do déficit nutricional entre as crianças do estudo. Os fatores associados ao déficit nutricional ratificam a contribuição de questões sociais na gênese da desnutrição.

Towards Sustainable ASEAN Port Development: Challenges and Opportunities for Vietnamese Ports

Directory of Open Access Journals (Sweden)

Saeyeon Roh

2016-06-01

Full Text Available Sustainability agendas are challenging port authorities around the world to find ways of operating and managing their ports efficiently and effectively in terms of economic, social, as well as environmental development. In this respect, governments in ASEAN countries have been implementing various green activities seeking to reduce the environmental impact of shipping and related activities. In this connection, most studies in the existing literature mainly focus on the environmental aspects of sustainable development and have not clearly explained what sustainable port development exactly entails. Furthermore, most of these studies emphasized on the impact of port development and overlooked what factors influence sustainable port development. To address these gaps, this research aim to explore the main factors shaping sustainable port development. This was conducted through a comprehensive review of related literature as well as confirmatory in-depth interviews with port authorities. As a result, findings from this research would help identify key elements of sustainable port development from port authorities’ perspective. The challenges, opportunities and managerial implications for Vietnamese ports are also discussed accordingly.

Port-Wine Stains

Science.gov (United States)

... Safe Videos for Educators Search English Español Port-Wine Stains KidsHealth / For Parents / Port-Wine Stains What's ... Manchas de vino de oporto What Are Port-Wine Stains? A port-wine stain is a type ...

Fewer-than-four ports versus four ports for laparoscopic cholecystectomy.

Science.gov (United States)

Gurusamy, Kurinchi Selvan; Vaughan, Jessica; Rossi, Michele; Davidson, Brian R

2014-02-20

Traditionally, laparoscopic cholecystectomy is performed using two 10-mm ports and two 5-mm ports. Recently, a reduction in the number of ports has been suggested as a modification of the standard technique with a view to decreasing pain and improving cosmesis. The safety and effectiveness of using fewer-than-four ports has not yet been established. To assess the benefits (such as improvement in cosmesis and earlier return to activity) and harms (such as increased complications) of using fewer-than-four ports (fewer-than-four-ports laparoscopic cholecystectomy) versus four ports in people undergoing laparoscopic cholecystectomy for any reason (symptomatic gallstones, acalculous cholecystitis, gallbladder polyp, or any other condition). We searched the Cochrane Central Register of Controlled Trials (CENTRAL; Issue 8, 2013), MEDLINE, EMBASE, Science Citation Index Expanded, and the World Health Organization International Clinical Trials Registry Platform portal to September 2013. We included all randomised clinical trials comparing fewer-than-four ports versus four ports, that is, with standard laparoscopic cholecystectomy that is performed with two ports of at least 10-mm incision and two ports of at least 5-mm incision. Two review authors independently identified the trials and extracted the data. We analysed the data using both the fixed-effect and the random-effects models. For each outcome, we calculated the risk ratio (RR) or mean difference (MD) with 95% confidence intervals (CI) based on intention-to-treat analysis, whenever possible. We found nine trials with 855 participants that randomised participants to fewer-than-four-ports laparoscopic cholecystectomy (n = 427) versus four-port laparoscopic cholecystectomy (n = 428). Most trials included low anaesthetic risk participants undergoing elective laparoscopic cholecystectomy. Seven of the nine trials used a single port laparoscopic cholecystectomy and the remaining two trials used three-port laparoscopic

Integration of thin film giant magnetoimpedance sensor and surface acoustic wave transponder

KAUST Repository

Li, Bodong

2012-03-09

Passive and remote sensing technology has many potential applications in implantable devices, automation, or structural monitoring. In this paper, a tri-layer thin film giant magnetoimpedance (GMI) sensor with the maximum sensitivity of 16%/Oe and GMI ratio of 44% was combined with a two-port surface acoustic wave(SAW) transponder on a common substrate using standard microfabrication technology resulting in a fully integrated sensor for passive and remote operation. The implementation of the two devices has been optimized by on-chip matching circuits. The measurement results clearly show a magnetic field response at the input port of the SAW transponder that reflects the impedance change of the GMI sensor.

Integration of thin film giant magnetoimpedance sensor and surface acoustic wave transponder

KAUST Repository

Li, Bodong; Salem, Nedime Pelin M. H.; Giouroudi, Ioanna; Kosel, Jü rgen

2012-01-01

Passive and remote sensing technology has many potential applications in implantable devices, automation, or structural monitoring. In this paper, a tri-layer thin film giant magnetoimpedance (GMI) sensor with the maximum sensitivity of 16%/Oe and GMI ratio of 44% was combined with a two-port surface acoustic wave(SAW) transponder on a common substrate using standard microfabrication technology resulting in a fully integrated sensor for passive and remote operation. The implementation of the two devices has been optimized by on-chip matching circuits. The measurement results clearly show a magnetic field response at the input port of the SAW transponder that reflects the impedance change of the GMI sensor.

A Compact, Versatile Six-Port Radar Module for Industrial and Medical Applications

Directory of Open Access Journals (Sweden)

Sarah Linz

2013-01-01

Full Text Available The Six-port receiver has been intensively investigated in the last decade to be implemented as an alternative radar architecture. Plenty of current scientific publications demonstrate the effectiveness and versatility of the Six-port radar for special industrial, automotive, and medical applications, ranging from accurate contactless vibration analysis, through automotive radar calibration, to remote breath and heartbeat monitoring. Its highlights, such as excellent phase discrimination, trivial signal processing, low circuit complexity, and cost, have lately drawn the attention of companies working with radar technology. A joint project involving the University of Erlangen-Nuremberg and InnoSenT GmbH (Innovative Sensor Technology led to the development of a highly accurate, compact, and versatile Six-port radar module aiming at a reliable high-integration of all subcomponents such as antenna, Six-port front-end, baseband circuitry, and digital signal processing in one single package. Innovative aspects in the RF front-end design as well as in the integration strategy are hereby presented, together with a system overview and measurement results.

Strategic port development

DEFF Research Database (Denmark)

Olesen, Peter Bjerg; Dukovska-Popovska, Iskra; Hvolby, Hans-Henrik

2014-01-01

While large global ports are recognised as playing a central role in many supply chains as logistic gateways, smaller regional ports have been more stagnant and have not reached the same level of development as the larger ports. The research literature in relation to port development is also...

Interior Space: Representation, Occupation, Well-Being and Interiority

OpenAIRE

Power, Jacqueline

2014-01-01

This article will provide an overview of space as it is understood and engaged with from within the discipline of interior design/interior architecture. Firstly, the term interior will be described. Secondly, the paper will discuss space as a general concept, before exploring what space is speifically for the interior design/interior architecture discipline. How is space understood? What does space "look" like for interuior designers/interior architects?.

Port of Rotterdam

NARCIS (Netherlands)

Veenstra, A.W.

2014-01-01

The port of Rotterdam is one of the largest ports in the World and has great significance for the Dutch and European economy. Newly appointed TU/e professor Albert Veenstra explains if and how the Port of Rotterdam is affected by the economic crisis. With other European ports closing in, what can

Engineering issues on the diagnostic port integration in ITER upper port 18

Energy Technology Data Exchange (ETDEWEB)

Pak, Sunil, E-mail: paksunil@nfri.re.kr [National Fusion Research Institute, Gwahak-ro, Yuseong-gu, Daejeon (Korea, Republic of); Bertalot, Luciano [ITER Organization, Route de Vinon sur Verdon, 13115 St Paul-lez-Durance (France); Cheon, Mun Seong [National Fusion Research Institute, Gwahak-ro, Yuseong-gu, Daejeon (Korea, Republic of); Giacomin, Thibaud [ITER Organization, Route de Vinon sur Verdon, 13115 St Paul-lez-Durance (France); Heemskerk, Cock J.M.; Koning, Jarich F. [Heemskerk Innovative Technology, Merelhof 2, 2172 HZ Sassenheim (Netherlands); Lee, Hyeon Gon [National Fusion Research Institute, Gwahak-ro, Yuseong-gu, Daejeon (Korea, Republic of); Nemtcev, Grigorii [Institution “PROJECT CENTER ITER”, Akademika Kurchatova sq., Moscow (Russian Federation); Ronden, Dennis M.S. [FOM Institute DIFFER, P.O. Box 1207, 3430 BE Nieuwegein (Netherlands); Seon, Chang Rae [National Fusion Research Institute, Gwahak-ro, Yuseong-gu, Daejeon (Korea, Republic of); Udintsev, Victor; Yukhnov, Nikolay [ITER Organization, Route de Vinon sur Verdon, 13115 St Paul-lez-Durance (France); Zvonkov, Alexander [Institution “PROJECT CENTER ITER”, Akademika Kurchatova sq., Moscow (Russian Federation)

2016-11-01

Highlights: • Diagnostic port integration in the upper port 18 of ITER is presented in order to house the three diagnostic systems. • Issue on the neutron shielding in the upper port 18 is addressed and the shut-down dose rate in the interspace is summarized. • The maintenance strategy in the upper port 18 is described. - Abstract: The upper port #18 (UP18) in ITER hosts three diagnostic systems: the neutron activation system, the Vacuum Ultra-Violet spectrometer system, and the vertical neutron camera. These diagnostics are integrated into three infrastructures in the port: the upper port plug, interspace support structure and port cell support structure. The port integration in UP18 is at the preliminary design stage and the current design of the infrastructure as well as the diagnostic integration is described here. The engineering issues related to neutron shielding and maintenance are addressed and the design approach is suggested.

Perancangan Interior “Interior World Center” di Surabaya

OpenAIRE

Handojo, Renita Olivia

2014-01-01

Interior World Center is a place that contain all needs and matters related to world of interior. The main purpose of Interior World Center is to give access and facilitate people in fulfill their needs that concern and correspond with interior world, that is to say with combine and integrate several interior activity into one in corporated place. Inside of this building there are several commercial space related with the interior world. The commercial spaces will support each other in order ...

Vehicle Based Vector Sensor

Science.gov (United States)

2015-09-28

buoyant underwater vehicle with an interior space in which a length of said underwater vehicle is equal to one tenth of the acoustic wavelength...underwater vehicle with an interior space in which a length of said underwater vehicle is equal to one tenth of the acoustic wavelength; an...unmanned underwater vehicle that can function as an acoustic vector sensor. (2) Description of the Prior Art [0004] It is known that a propagating

The Re-Conceptualization of the Port Supply Chain as a Smart Port Service System: The Case of the Port of Salerno

Directory of Open Access Journals (Sweden)

Antonio Botti

2017-04-01

Full Text Available This paper proposes a re-conceptualization of the port supply chain as a smart service system, in accordance with the theory of service science. Starting from a short literature review about the port supply chain approach and service science, a new comprehensive framework is provided to better understand seaport dynamics and the creation of competitive port supply chains. The methodology used is the case study approach. The Authors examined the Port of Salerno (Italy and re-conceptualized it as a smart port service system. The originality of the work lies in the application of service science as a lens to re-conceptualize the port supply chain, that allows the implementation of a logistic framework. Both theoretical and practical implications are provided to enrich the literature about port supply chains and to support port operators.

Fast Air Temperature Sensors

DEFF Research Database (Denmark)

Hendricks, Elbert

1998-01-01

The note documents briefly work done on a newly developed sensor for making fast temperature measurements on the air flow in the intake ports of an SI engine and in the EGR input line. The work reviewed has been carried out in close cooperation with Civ. Ing. Michael Føns, the author (IAU...

Flat-port connectors

KAUST Repository

Alrashed, Mohammed

2017-01-01

and water resistant. It is unique in the way of using the outer surfaces of the device for the electrical connection between the ports. Flat-port design can allow the manufacture of extremely thin devices by eliminating the side ports slots that take a lot

Integrated circuit test-port architecture and method and apparatus of test-port generation

Science.gov (United States)

Teifel, John

2016-04-12

A method and apparatus are provided for generating RTL code for a test-port interface of an integrated circuit. In an embodiment, a test-port table is provided as input data. A computer automatically parses the test-port table into data structures and analyzes it to determine input, output, local, and output-enable port names. The computer generates address-detect and test-enable logic constructed from combinational functions. The computer generates one-hot multiplexer logic for at least some of the output ports. The one-hot multiplexer logic for each port is generated so as to enable the port to toggle between data signals and test signals. The computer then completes the generation of the RTL code.

Sea freight - Antwerp Port

Directory of Open Access Journals (Sweden)

NEACSU Nicoleta Andreea

2017-01-01

Full Text Available Shipping plays a vital role in achieving the movement of goods, both in terms of quantity and efficiency. This paper presents the role and advantages of shipping in the global economy and analyzes the development and Antwerp Port activity. Currently, the second most important trading port in Europe and 14th in the ranking of most important ports that handle containers worldwide, the Port of Antwerp, Belgium is a port in the heart of Europe, accessible to large sized vessels. 200 years of constructing infrastructure and logistics around the central location, as well as pressure from Rotterdam, that had an impact on the competitiveness of the port of Antwerp, all this led the port to occupy a leading position in the top rankings.

Determinants of Port Performance - Case Study of 4 Main Ports in Indonesia (2005-2015

Directory of Open Access Journals (Sweden)

Atika Aqmarina

2018-03-01

Full Text Available Port plays significant role in supporting economic growth of a country. This study aims to analyze the determinant of port performance in Indonesia. In this research, the ports selected are four main ports in Indonesia which are Port of Belawan, Port of Tanjung Priok, Port of Tanjung Perak, and Makassar. These ports are designed as the hub ports in the national sea transport system of the country. The study used pooled OLS as the methodology to analyze the determinant. The result of this studies shows that total traffic is not influenced by operating surplus per ton, whereas the rest of variables such as turnaround time, idle time, berth of occupancy rate, rate of return, number of employee and cargo equipment have significant results and significantly influenced the total traffic.

ITER lower port systems integration

Energy Technology Data Exchange (ETDEWEB)

Levesy, B., E-mail: bruno.levesy@iter.org [ITER Organization, CS 90 046, 13067 St Paul Lez Durance Cedex (France); Baker, D.; Boussier, B.; Bryan, S.; Cordier, J.J.; Dremel, M.; Dell' Orco, G.; Daly, E.; Doshi, B.; Jeannoutot, T.; Friconneau, J.P.; Gliss, C.; Le Barbier, R.; Lachevre, F.; Loughlin, M.; Martin, A.; Martins, J.P.; Maruyama, S.; Palmer, J.; Reichle, R. [ITER Organization, CS 90 046, 13067 St Paul Lez Durance Cedex (France)

2011-10-15

The lower port systems are installed inside the vacuum vessel lower ports and in the adjacent port cells. The vacuum vessel ports and penetrations are allocated as follow: -4 ports dedicated to remote handling of the divertor cassettes, contain diagnostics racks and divertor cooling pipes. -5 ports connecting the main vessel to the torus cryopumps, contain divertor cooling pipes, pellet and gas injection pipes and vertical stabilization coil feeders. -3 penetrations connecting torus cryopumps are connected to the vacuum vessel by branch pipes. -Specific penetrations for divertor cooling lines, in-vessel viewing and glow discharge systems. The general layout of the port systems has been revised recently to improve the cryopump (8 t weight, 1.8 m diameter and 2.5 m long) maintenance scheme with remote handling tools and integrate the in-vessel vertical stabilization coil feeders. The port allocation, the pumping ports design, and interfaces in-between ports and cryostat and in-between cryopumps and cryostat have been up-dated. The integration inside the 18 port cells (11 m x 4 m each) has been reviewed to avoid clashes in between systems and to fix the openings in the port cell concrete walls. The new layout integrates safety and neutron-shielding requirements as well as remote handling and maintenance compatibility for the different systems. The paper presents the up-dated integration of the lower port systems inside the ports and the port cells. Interfaces of the port systems with the vacuum vessel, the cryostat and the port cells are described.

Principal Ports

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Principal Ports are defined by port limits or US Army Corps of Engineers (USACE) projects, these exclude non-USACE projects not authorized for publication. The...

Management of Port Operations

OpenAIRE

Gheorghe BASANU; Georgiana NUKINA

2011-01-01

The Management of port operation requires the proper and efficient use of port facility, equipment for cargo handling, berth facilities, waterways and roads. It also entails the use of effective communications system, storage facilities, and dockworkers. The whole activities mentioned above form the bulk of port operations. The aspiration of port operator is to get cargo through the gateway of ports as fast as possible on to other modes of transport (rail or road) with a minimal cost to them ...

The Windows serial port programming handbook

CERN Document Server

Bai, Ying

2004-01-01

The fundamentals of serial port communications. Serial port programming in ANSI C and Assembly languages for MS-DOS. Serial ports interface developed in VC++ 6.0. Serial port programming in Visual Basic. Serial port programming in LabVIEW. Serial port programming in MATLAB. Serial port programming in Smalltalk. Serial port programming in Java.

Maintaining and Researching Port Safety: A Case Study of the Port of Kaohsiung

OpenAIRE

Tseng, Po-Hsing.; Pilcher, Nick.

2017-01-01

Maintaining port safety in full conformity with IMO standards is a requisite for every port and country. To do this, understanding the challenges and human factors involved is key. To date, much research has shed valuable light on these factors and considered how to address them. One aspect that is often noted is that both maintaining port safety and researching port safety presents numerous challenges. This paper considers both these aspects in the context of a case study of port safety in K...

Shipping emissions in ports

OpenAIRE

Merk, Olaf

2014-01-01

Shipping emissions in ports are substantial, accounting for 18 million tonnes of CO2 emissions, 0.4 million tonnes of NOx, 0.2 million of SOx and 0.03 million tonnes of PM10 in 2011. Around 85% of emissions come from containerships and tankers. Containerships have short port stays, but high emissions during these stays. Most of CO2 emissions in ports from shipping are in Asia and Europe (58%), but this share is low compared to their share of port calls (70%). European ports have much less emi...

19 CFR 101.3 - Customs service ports and ports of entry.

Science.gov (United States)

2010-04-01

... and Service Ports. Many of the ports listed were created by the President's message of March 3, 1913....S.C. 1). Subsequent orders of the President or of the Secretary of the Treasury which affected these... Port of the Delaware River and Bay described in T.D. 96-4. Perth Amboy New Mexico Albuquerque Including...

Virtual sensors for active noise control in acoustic-structural coupled enclosures using structural sensing: robust virtual sensor design.

Science.gov (United States)

Halim, Dunant; Cheng, Li; Su, Zhongqing

2011-03-01

The work was aimed to develop a robust virtual sensing design methodology for sensing and active control applications of vibro-acoustic systems. The proposed virtual sensor was designed to estimate a broadband acoustic interior sound pressure using structural sensors, with robustness against certain dynamic uncertainties occurring in an acoustic-structural coupled enclosure. A convex combination of Kalman sub-filters was used during the design, accommodating different sets of perturbed dynamic model of the vibro-acoustic enclosure. A minimax optimization problem was set up to determine an optimal convex combination of Kalman sub-filters, ensuring an optimal worst-case virtual sensing performance. The virtual sensing and active noise control performance was numerically investigated on a rectangular panel-cavity system. It was demonstrated that the proposed virtual sensor could accurately estimate the interior sound pressure, particularly the one dominated by cavity-controlled modes, by using a structural sensor. With such a virtual sensing technique, effective active noise control performance was also obtained even for the worst-case dynamics. © 2011 Acoustical Society of America

Wireless sensors and sensor networks for homeland security applications.

Science.gov (United States)

Potyrailo, Radislav A; Nagraj, Nandini; Surman, Cheryl; Boudries, Hacene; Lai, Hanh; Slocik, Joseph M; Kelley-Loughnane, Nancy; Naik, Rajesh R

2012-11-01

New sensor technologies for homeland security applications must meet the key requirements of sensitivity to detect agents below risk levels, selectivity to provide minimal false-alarm rates, and response speed to operate in high throughput environments, such as airports, sea ports, and other public places. Chemical detection using existing sensor systems is facing a major challenge of selectivity. In this review, we provide a brief summary of chemical threats of homeland security importance; focus in detail on modern concepts in chemical sensing; examine the origins of the most significant unmet needs in existing chemical sensors; and, analyze opportunities, specific requirements, and challenges for wireless chemical sensors and wireless sensor networks (WSNs). We further review a new approach for selective chemical sensing that involves the combination of a sensing material that has different response mechanisms to different species of interest, with a transducer that has a multi-variable signal-transduction ability. This new selective chemical-sensing approach was realized using an attractive ubiquitous platform of battery-free passive radio-frequency identification (RFID) tags adapted for chemical sensing. We illustrate the performance of RFID sensors developed in measurements of toxic industrial materials, humidity-independent detection of toxic vapors, and detection of chemical-agent simulants, explosives, and strong oxidizers.

Evaluation of the Necessity of Port Fixation in Central Venous Port Implantation

Energy Technology Data Exchange (ETDEWEB)

Kim, Sang Su; Kim, Hyung Pil [Inje University Pusan Paik Hospital, Busan (Korea, Republic of); Bae, Jae Ik; Won, Je Hwan [Ajou University School of Medicine, Suwon (Korea, Republic of)

2010-06-15

The technical success and complications were especially focused on and evaluated the need for fixation of a port under fluoroscopic guidance placement of the totally implantable central venous access ports for long term central venous access. Two hundred eighty nine consecutive patients (170 men, 119 women, mean age: 52-year-old) who underwent venous port implantation for the administration of chemotherapy were followed over a 1-month period. The procedures were performed in the angiographic suite by an interventional radiologist and all access was through the right jugular vein, except for the patients who had undergone a right mastectomy. The procedures were performed in the following order: 1) venous puncture, 2) making a pocket, 3) catheter tunneling, 4) port insertion, 5) catheter sizing, and 6) insertion. A port which was connected to the tunneled catheter was inserted into the minimally sized subcutaneous pocket with the aid of a small retractor. A follow-up was performed with medical records and chest radiographs. The follow-up period for evaluating the venous port ranged from 59 to 329 days (mean: 175 days) The procedures performed to gain right jugular vein access were successful without difficulty in all cases. The 18 patients that underwent procedures to gain left jugular vein access encountered some difficulty upon insertion of a catheter into the SVC due to encountering the tortuous left brachiocephalic vein. No complications occurred during and immediately after the procedure. In one case the port chamber rotated within the subcutaneous pocket; however, no catheter migration or malfunction occurred. If port insertion was followed by catheter insertion, the port chamber can be tightly implanted in the minimally sized pocket. This would avoid the need for fixation of the catheter to the port chamber leading into the pocket

Evaluation of physical-protection elements for interior applications

International Nuclear Information System (INIS)

Scott, S.H.

1983-01-01

Considerable emphasis has been given in recent years to the threat of sabotage by an insider at nuclear facilities. This threat is inherently different from the outsider threat of theft or sabotage because of the insiders' unique knowledge and access to vital material and equipment. Thus, special safeguards elements are needed in order to counter the insider threat. In addition, insider physical protection system elements must be compatible with the operations, safety, and maintenance programs at the facility. To help identify elements which meet these needs, field evaluations were performed on an interior access control system, piping sensors, interior video motion detectors, and valve monitoring devices. These elements were tested in a realistic operating environment and both technical and operational evaluation data were obtained. Safeguards element descriptions and the results of the operational tests and evaluations are outlined

Intake port

Science.gov (United States)

Mendler, Edward Charles

2005-02-01

The volumetric efficiency and power of internal combustion engines is improved with an intake port having an intake nozzle, a venturi, and a surge chamber. The venturi is located almost halfway upstream the intake port between the intake valves and the intake plenum enabling the venturi throat diameter to be exceptionally small for providing an exceptionally high ram velocity and an exceptionally long and in turn high efficiency diffuser flowing into the surge chamber. The intake port includes an exceptionally large surge chamber volume for blow down of the intake air into the working cylinder of the engine.

Video and thermal imaging system for monitoring interiors of high temperature reaction vessels

Science.gov (United States)

Saveliev, Alexei V [Chicago, IL; Zelepouga, Serguei A [Hoffman Estates, IL; Rue, David M [Chicago, IL

2012-01-10

A system and method for real-time monitoring of the interior of a combustor or gasifier wherein light emitted by the interior surface of a refractory wall of the combustor or gasifier is collected using an imaging fiber optic bundle having a light receiving end and a light output end. Color information in the light is captured with primary color (RGB) filters or complimentary color (GMCY) filters placed over individual pixels of color sensors disposed within a digital color camera in a BAYER mosaic layout, producing RGB signal outputs or GMCY signal outputs. The signal outputs are processed using intensity ratios of the primary color filters or the complimentary color filters, producing video images and/or thermal images of the interior of the combustor or gasifier.

Grain boundary and grain interior conduction in γ'-Bi2MoO6

International Nuclear Information System (INIS)

Vera, C.M.C.; Aragon, R.

2005-01-01

Impedance spectroscopy of fine grained ( 2 MoO 6 samples, in the frequency range of 0.1 Hz-250 kHz, relevant to sensor applications, up to 800 deg. C, has been used to characterize grain boundary and grain interior contributions to conduction. Above 500 deg. C, the grain boundary contribution is no longer rate limiting and conduction is dominated by the grain interior component. The corresponding activation energies are 0.98 eV for grain boundary and 0.73 eV for grain interior components. The weak dependence of conductivity on oxygen partial pressure below 500 deg. C can be attributed to electrode-electrolyte interface phenomena, whereas the robust response to ethanol is commensurate with changes in intrinsic ionic conductivity

Shutdown dose rates at ITER equatorial ports considering radiation cross-talk from torus cryopump lower port

Energy Technology Data Exchange (ETDEWEB)

Juárez, Rafael, E-mail: rjuarez@ind.uned.es [Departamento de Ingeniería Energética, ETSII-UNED, Calle Juan del Rosal 12, Madrid 28040 (Spain); Pampin, Raul [F4E, Torres Diagonal Litoral B3, Josep Pla 2, Barcelona 08019 (Spain); Levesy, Bruno [ITER Organization, 13115 Route de Vinon sur Verdon, St Paul Lez Durance (France); Moro, Fabio [ENEA, Via Enrico Fermi 45, Frascati, Rome (Italy); Suarez, Alejandro [ITER Organization, 13115 Route de Vinon sur Verdon, St Paul Lez Durance (France); Sanz, Javier [Departamento de Ingeniería Energética, ETSII-UNED, Calle Juan del Rosal 12, Madrid 28040 (Spain)

2015-11-15

Shutdown dose rates for planned maintenance purposes is an active research field in ITER. In this work the radiation (neutron and gamma) cross-talk between ports in the most conservative case foreseen in ITER is investigated: the presence of a torus cryopump lower port, mostly empty for pumping efficiency reasons. There will be six of those ports: #4, #6, #10, #12, #16 and #18. The equatorial ports placed above them will receive a significant amount of additional radiation affecting the shutdown dose rates during in situ maintenance activities inside the cryostat, and particularly in the port interspace area. In this study a general situation to all the equatorial ports placed above torus cryopump lower ports is considered: a generic diagnostics equatorial port placed above the torus cryopump lower port (LP#4). In terms of shutdown dose rates at equatorial port interspace after 10{sup 6} s of cooling time, 405 μSv/h has been obtained, of which 160 μSv/h (40%) are exclusively due to radiation cross-talk from a torus cryopump lower port. Equatorial port activation due to only “local neutrons” contributes 166 μSv/h at port interspace, showing that radiation cross-talk from such a lower port is a phenomenon comparable in magnitude to the neutron leakage though the equatorial port plug.

An overview of San Francisco Bay PORTS

Science.gov (United States)

Cheng, Ralph T.; McKinnie, David; English, Chad; Smith, Richard E.

1998-01-01

The Physical Oceanographic Real-Time System (PORTS) provides observations of tides, tidal currents, and meteorological conditions in real-time. The San Francisco Bay PORTS (SFPORTS) is a decision support system to facilitate safe and efficient maritime commerce. In addition to real-time observations, SFPORTS includes a nowcast numerical model forming a San Francisco Bay marine nowcast system. SFPORTS data and nowcast numerical model results are made available to users through the World Wide Web (WWW). A brief overview of SFPORTS is presented, from the data flow originated at instrument sensors to final results delivered to end users on the WWW. A user-friendly interface for SFPORTS has been designed and implemented. Appropriate field data analysis, nowcast procedures, design and generation of graphics for WWW display of field data and nowcast results are presented and discussed. Furthermore, SFPORTS is designed to support hazardous materials spill prevention and response, and to serve as resources to scientists studying the health of San Francisco Bay ecosystem. The success (or failure) of the SFPORTS to serve the intended user community is determined by the effectiveness of the user interface.

Generic Diagnostic Port Integration for the Equatorial Port Plug of ITER

International Nuclear Information System (INIS)

Doceul, L.; Chappuis, Ph.; Portafaix, Ch.; Guillaume, T.; Bruyere, Ch.; Walker, Ch.; Ingesson, Ch.; Ciattaglia, E.; Salasca, S.; Eric, T.

2006-01-01

ITER requires an extensive set of diagnostic systems to provide several key functions such as protection of the device, input to plasma control systems and evaluation of the plasma performance. Most of these diagnostics system are to be integrated in port plugs, which are water cooled stainless steel structures (approximately: 50 t, 2 m x 2 m x 4 m) inserted into the vacuum-vessel ports. The port plug must perform basic functions such as providing neutron and gamma shielding, supporting the first wall armour and shielding blanket material, closing the vacuum vessel ports, supporting the diagnostic equipment (within the primary vacuum, on the primary vacuum boundary and in the port interspace). CEA (Commissariat l'Energie Atomique) has contributed to the engineering activities on the port plugs and has more particularly focused on the design and diagnostic integration in the representative equatorial port plug EQ01. The specific CEA contributions were to perform the general engineering, structural and thermal analysis. These detailed analysis have highlighted some design issues which were worked out through different solutions. This paper will contain the description of the engineering activities performed such as: - The conceptual design of the EQ01 and the associated diagnostics, such as the visible and infrared optical diagnostic, - The static mechanical calculations, taking into account the electromagnetic loads occurring during fast transient plasma events, - The dynamic calculation constituted of modal and transient analysis under the same electromagnetic loads to estimate the dynamic amplification factor due to the resonance phenomenon, - The thermal assessment under the neutronic load of the water-cooled stainless steel structure, - The seismic response of the port plug inside the vacuum vessel, taking into account the ground spectra and soil conditions in the Cadarache site. (author)

A wireless sensor tag platform for container security and integrity

Science.gov (United States)

Amaya, Ivan A.; Cree, Johnathan V.; Mauss, Fredrick J.

2011-04-01

Cargo containers onboard ships are widely used in the global supply chain. The need for container security is evidenced by the Container Security Initiative launched by the U.S. Bureau of Customs and Border Protection (CBP). One method of monitoring cargo containers is using low power wireless sensor tags. The wireless sensor tags are used to set up a network that is comprised of tags internal to the container and a central device. The sensor network reports alarms and other anomalies to a central device, which then relays the message to an outside network upon arrival at the destination port. This allows the port authorities to have knowledge of potential security or integrity issues before physically examining the container. Challenges of using wireless sensor tag networks for container security include battery life, size, environmental conditions, information security, and cost among others. PNNL developed an active wireless sensor tag platform capable of reporting data wirelessly to a central node as well as logging data to nonvolatile memory. The tags, operate at 2.4 GHz over an IEEE 802.15.4 protocol, and were designed to be distributed throughout the inside of a shipping container in the upper support frame. The tags are mounted in a housing that allows for simple and efficient installation or removal prior to, during, or after shipment. The distributed tags monitor the entire container volume. The sensor tag platform utilizes low power electronics and provides an extensible sensor interface for incorporating a wide range of sensors including chemical, biological, and environmental sensors.

Getting Port Governance Right

DEFF Research Database (Denmark)

de Langen, Peter; Saragiotis, Periklis

2018-01-01

This chapter discusses the relevance of ports for economic development and next identifies port governance as a critical determinant of a well-functioning port industry. While in the past decades privately owned terminal operating companies have emerged and contributed to more efficient supply ch...

Reduced-port robotic total mesorectal resection for rectal cancer using a single-port access: a technical note.

Science.gov (United States)

Bae, Sung Uk; Jeong, Woon Kyung; Baek, Seong Kyu

2017-12-01

Single-port laparoscopic surgery has some advantages, including improved cosmetic outcomes and minimized parietal trauma. However, pure single-port laparoscopic rectal cancer surgery is challenging because of the difficulties in creating triangulation and applying the laparoscopic staplers with sufficient distal margins in the narrow pelvic cavity. Recently, a reduced-port robotic operation with a robotic single-port access plus one wristed robotic arm for colon cancer was introduced to overcome the limitations of single-port laparoscopic rectal surgery. Single-port laparoscopic surgery has some advantages, including improved cosmetic outcomes and minimized parietal trauma. However, the pure single-port laparoscopic rectal cancer operation is challenging. Recently, a reduced-port robotic operation with a robotic single-port access plus one wristed robotic arm for colon cancer was introduced to overcome the limitations of single-port laparoscopic rectal surgery. We performed a single-port plus an additional port robotic operation using a robotic single-port access through the umbilical incision, and the wristed robotic instruments were inserted through an additional robotic port in the right lower quadrant. The total operative and docking times were 310 min and 25 min, respectively. The total number of lymph nodes harvested was 12, and the proximal and distal resection margins were 11.1 and 2 cm, respectively. The patient was discharged on postoperative day 12 uneventfully. Based on a representative case, reduced-port robotic total mesorectal excision for rectal cancer using the single-port access appears to be feasible and safe. This approach could overcome the limitations of single-port laparoscopic rectal surgery.

Limited Scope Design Study for Multi-Sensor Towbody

Science.gov (United States)

2016-06-01

ports 2 Leak sensors 1 Electrical Surface supply voltage 300 V nominal (250–425 Vdc) Towbody output voltages 48/24/12 Vdc Load power...shallow water (អ m) at thousands of current and former Department of Defense (DoD) sites encompassing millions of acres. This design study...addresses the munitions remediation in shallow water problem with a system that uses a Multi-Sensor Towbody (MuST) and surface vessel with support

Application of Game Theory and Uncertainty Theory in Port Competition between Hong Kong Port and Shenzhen Port

Directory of Open Access Journals (Sweden)

Thi Minh Hoang Do

2015-06-01

Full Text Available This paper unveils the strong competition in container cargo between Hong Kong Port which has been emerging as an international maritime center since the 1970s and Shenzhen Port which has recently gained remarkable achievements in the Pearl River Delta region. Among various competing strategies, the study focuses on the long-term one in which two ports will decide to compete by investing in capacity. The purpose of this research is to examine their decision making process and to suggest future strategic actions in the current situation. Within its scope, only economic profit brought back from the investment is considered. For this reason, an uncertain payoff two-person game model is developed where an uncertain factor of demand is involved. In applying Uncertainty theory (Liu, 2013, the two methods to solve the game are introduced, including uncertain statistics and the expected Nash Equilibrium strategy. The results obtained from this research generate meaningful suggestions for future competition plan for the two selected ports, which conclude that Shenzhen is the dominant port in this long-term strategy. Compared to existing works on the same topic, the paper shows its distinctiveness by studying the latest competitive situation with regard to the uncertain demand in the game model.

Inland Ports in the Republic of Croatia: Approvals for Port Activities instead of Concessions

Directory of Open Access Journals (Sweden)

Goran Vojković

2008-11-01

Full Text Available According to the 1998 Act on Inland Ports, the right to performall port activities within inland ports of the Republic ofCroatia is given on the basis of concession, obtained throughbidding. It has been noticed in practice that modem businessprocesses and traffic flows are more dynamic than before whenclassic concession relations were created. Also, types andamounts of cargo are changing every couple of years, which isfollowed by quick adjustments, instead of working according torigid and long-term defined decisions and concession contracts.Furthermore, the practice has shown for some activitiesthat the number of port providers (such as ship suppliers,port-agency and freight forwarders should not be limited. Thismeans that the system of a limited number of port providers isimportant only for the activities that require location within aport, as the port area is physically limited. Therefore, the newAct on Navigation and Inland Ports from 2007, whose framehas been completed by sub-law acts during 2008, has replacedthe complex concession system for performing activities in inlandports by a more liberal approval system. On the basis ofthese, higher dynamics of work of port providers is enabled aswell as easier adjustment to market conditions. Furthermore,the main limitation factor that determines the number of portusers becomes the available physical space within a port, whichprovides undisturbed competition, along with larger offer ofport services that do not require that space. It is also importantto point out that the new Act specifically includes distributionand cargo logistics, also processing and improvement of goodsas well as industrial activities including production that enablecomplete economic utilization of port capacities into the existingport activities, thus significantly changing the role of the portitself as a logistic centre.

Multiple-port valve

International Nuclear Information System (INIS)

Doody, T.J.

1978-01-01

A multiple-port valve assembly is designed to direct flow from a primary conduit into any one of a plurality of secondary conduits as well as to direct a reverse flow. The valve includes two mating hemispherical sockets that rotatably receive a spherical valve plug. The valve plug is attached to the primary conduit and includes diverging passageways from that conduit to a plurality of ports. Each of the ports is alignable with one or more of a plurality of secondary conduits fitting into one of the hemispherical sockets. The other hemispherical socket includes a slot for the primary conduit such that the conduit's motion along that slot with rotation of the spherical plug about various axes will position the valve-plug ports in respect to the secondary conduits

360 PORT MDA - A Strategy to Improve Port Security

Science.gov (United States)

2006-09-01

Participating Agencies (After: Executive Briefing..........................27 Table 6. Designated Joint Operations Center Participants (From: SAFE...Investigations CGIP Coast Guard Intelligence Program CHOC Charleston Harbor Operations Center CIO Command Intelligence Officer CMT Combating Maritime... EXECUTIVE SUMMARY Ports are critical to our economy and national security. Key hubs in the international trade network, U.S. ports accounted for more than

Port Stakeholder Summit - April 2014

Science.gov (United States)

EPA's National Port Stakeholders Summit, Advancing More Sustainable Ports, focused on actions to protect air quality while reducing climate risk and supporting economic growth, making ports more environmentally sustainable.

An Analysis of Port Service Quality and Customer Satisfaction: The Case of Korean Container Ports

Directory of Open Access Journals (Sweden)

Gi Tae Yeo

2015-12-01

Full Text Available Ports play a critical role in the economy of many countries and regions. Failure or unreliability of port services can significantly influence port customers—shipping lines and cargo owners—and result in their dissatisfaction. However, what constitutes port service quality (PSQ and its influence on the satisfaction of port customers has not been well investigated in the literature. Therefore, this study investigates the concept of PSQ and its influence on customer satisfaction in the case of Korean container ports. Following a literature review, a conceptual model of PSQ and its influence on customer satisfaction is proposed. The model was validated through a survey of 313 members of the Korean Port Logistics Association (KPLA. Partial least squares structural equation modeling (PLS-SEM was conducted to confirm the PSQ dimensions and to examine their relationship with customer satisfaction using SmartPLS 3.2.1 software. PSQ is found to be a five-factor construct, and its management, and image and social responsibility factors have significant positive effects on customer satisfaction. In addition to its academic contribution, this study also contributes to management practices because port managers can use the PSQ scale to measure their customers’ satisfaction and justify investments in the quality management of port services.

Concerning background from calorimeter ports

International Nuclear Information System (INIS)

Digiacomo, N.J.

1985-01-01

Any detector system viewing a port or slit in a calorimeter wall will see, in addition to the primary particles of interest, a background of charged and neutral particles and photons generated by scattering from the port walls and by leakage from incompletely contained primary particle showers in the calorimeter near the port. The signal to noise ratio attainable outside the port is a complex function of the primary source spectrum, the calorimeter and port design and, of course, the nature and acceptance of the detector system that views the port. Rather than making general statements about the overall suitability (or lack thereof) of calorimeter ports, we offer here a specific example based on the external spectrometer and slit of the NA34 experiment. This combination of slit and spectrometer is designed for fixed-target work, so that the primary particle momentum spectrum contains higher momentum particles than expected in a heavy ion colliding beam environment. The results are, nevertheless, quite relevant for the collider case

Non-Price Competition in the Port Sector: A Case Study of Ports in Turkey

OpenAIRE

Soner Esmer; Hong-Oanh Nguyen, Ph.D.; Yapa Mahinda Bandara, Ph.D.; Kazim Yeni, Ph.D.

2016-01-01

Although the port sector has been facing increasing competition, there is limited research on how ports compete using non-price competition strategies. There are a few studies on non-price competition in the port sector. However they mainly focus on the marketing aspect. This paper seeks to fill this gap in the literature, especially from a combined marketing-economic perspective. Especially the paper's main objective is to identify the determinants of non-price competition in the port sector...

Dynamism Patterns of Western Mediterranean Cruise Ports and the Coopetition Relationships Between Major Cruise Ports

Directory of Open Access Journals (Sweden)

Esteve-Perez Jeronimo

2018-03-01

Full Text Available The Mediterranean Sea has seen an increase of ports hosting cruise ships during the first fifteen years of the 21st century. The increase in cruise ship presence in Mediterranean ports is associated with the dynamism of cruise traffic in recent years, with an average annual growth of 7.45% for cruise passengers worldwide during the period of 1990-2015. Cruise traffic is a maritime business that is primarily composed of two elements, maritime affairs and tourism. This article focuses on the maritime component. With the growth of the cruise industry, cruise lines have been forced to seek new ports to meet demand in an attempt to create differentiated products based on the ports that compose the itinerary. The itinerary system of cruise traffic makes the cruise ports depend on one another to design an itinerary. This feature results in both complex geographic relationships in the design of a cruise itinerary and complex competitive/cooperative relationships between ports. The aim of this article is to present the hierarchic picture of a sample of 29 cruise ports in the Western Mediterranean region during the period of 2000-2015. To achieve this goal, a port size classification is proposed and a shift-share analysis at the inter- and intra-group size level is applied. Moreover, concentration measures are used to determine the changes in the levels of market concentration. Furthermore, a dynamic model is proposed to determine the competitive or cooperative relationships between cruise ports. The proposed model is applied to the largest ports with data from the 2001-2015 period.

Case Studies: Improving Environmental Performance and Economic Prosperity at Ports and in Near-Port Communities

Science.gov (United States)

Case Study links for improving environmental performance and economic prosperity at ports and in near-port communities. Case studies on equipment upgrades, jobs and benefits, land use and transportation, port-community engagement, and citizen science.

A demonstration of a low cost approach to security at shipping facilities and ports

Science.gov (United States)

Huck, Robert C.; Al Akkoumi, Mouhammad K.; Herath, Ruchira W.; Sluss, James J., Jr.; Radhakrishnan, Sridhar; Landers, Thomas L.

2010-04-01

Government funding for the security at shipping facilities and ports is limited so there is a need for low cost scalable security systems. With over 20 million sea, truck, and rail containers entering the United States every year, these facilities pose a large risk to security. Securing these facilities and monitoring the variety of traffic that enter and leave is a major task. To accomplish this, the authors have developed and fielded a low cost fully distributed building block approach to port security at the inland Port of Catoosa in Oklahoma. Based on prior work accomplished in the design and fielding of an intelligent transportation system in the United States, functional building blocks, (e.g. Network, Camera, Sensor, Display, and Operator Console blocks) can be assembled, mixed and matched, and scaled to provide a comprehensive security system. The following functions are demonstrated and scaled through analysis and demonstration: Barge tracking, credential checking, container inventory, vehicle tracking, and situational awareness. The concept behind this research is "any operator on any console can control any device at any time."

Vectorization, parallelization and porting of nuclear codes (porting). Progress report fiscal 1999

Energy Technology Data Exchange (ETDEWEB)

Kawasaki, Nobuo; Nemoto, Toshiyuki; Kawai, Wataru; Ishizuki, Shigeru [Fujitsu Ltd., Tokyo (Japan); Ogasawara, Shinobu; Kume, Etsuo; Adachi, Masaaki [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Yatake, Yo-ichi [Hitachi Ltd., Tokyo (Japan)

2001-01-01

Several computer codes in the nuclear field have been vectorized, parallelized and transported on the FUJITSU VPP500 system, the AP3000 system, the SX-4 system and the Paragon system at Center for Promotion of Computational Science and Engineering in Japan Atomic Energy Research Institute. We dealt with 18 codes in fiscal 1999. These results are reported in 3 parts, i.e., the vectorization and the parallelization part on vector processors, the parallelization port on scalar processors and the porting part. In this report, we describe the porting. In this porting part, the porting of Assisted Model Building with Energy Refinement code version 5 (AMBER5), general purpose Monte Carlo codes far neutron and photon transport calculations based on continuous energy and multigroup methods (MVP/GMVP), automatic editing system for MCNP library code (autonj), neutron damage calculations for materials irradiations and neutron damage calculations for compounds code (SPECTER/SPECOMP), severe accident analysis code (MELCOR) and COolant Boiling in Rod Arrays, Two-Fluid code (COBRA-TF) on the VPP500 system and/or the AP3000 system are described. (author)

The Flexible Port

NARCIS (Netherlands)

Taneja, P.

2013-01-01

Ports are beset with many uncertainties about their futures. They are confronted with new demands in terms of functions and scales, new external constraints, and changed expectations. The inability to adequately meet these demands can mean costly adaptations for a port, or loss of cargo and

Integrating Telco interoffice fiber transport with coaxial distribution

Science.gov (United States)

McCarthy, Steven M.

1993-02-01

Real success in the residential broadband market is contingent on a platform that most efficiently shares broadband port costs while at the same time affords us an elegant, and cost efficient, upgrade from today's analog to tomorrow's digital world. Spectrum transport, whether it be over new or existing fiber/coax systems or FTTC, is that platform. It is compatible with today's home entertainment market, can be evolved to future digital transport, and effectively shares the cost of interfacing with a broadband network.

Principal Ports and Facilities

Data.gov (United States)

California Natural Resource Agency — The Principal Port file contains USACE port codes, geographic locations (longitude, latitude), names, and commodity tonnage summaries (total tons, domestic, foreign,...

Principal Ports and Facilities

Data.gov (United States)

California Department of Resources — The Principal Port file contains USACE port codes, geographic locations (longitude, latitude), names, and commodity tonnage summaries (total tons, domestic, foreign,...

Handling of waste in ports

International Nuclear Information System (INIS)

Olson, P.H.

1994-01-01

The regulations governing the handling of port-generated waste are often national and/or local legislation, whereas the handling of ship-generated waste is governed by the MARPOL Convention in most parts of the world. The handling of waste consists of two main phases -collection and treatment. Waste has to be collected in every port and on board every ship, whereas generally only some wastes are treated and to a certain degree in ports and on board ships. This paper considers the different kinds of waste generated in both ports and on board ships, where and how it is generated, how it could be collected and treated. The two sources are treated together to show how some ship-generated waste may be treated in port installations primarily constructed for the treatment of the port-generated waste, making integrated use of the available treatment facilities. (author)

Vacuum vessel port structures for ITER-FEAT

International Nuclear Information System (INIS)

Utin, Yu.; Ioki, K.; Komarov, V.; Krylov, V.; Kuzmin, E.; Labusov, I.; Miki, N.; Onozuka, M.; Rozov, V.; Sannazzaro, G.; Tesini, A.; Yamada, M.; Barthel, Th.

2001-01-01

The equatorial and the upper port structures are the most loaded among those of the ITER-FEAT vacuum vessel (VV). For all of these ports, the VV closure plate and the in-port components are integrated into the port plug. The plugs/port structures are affected by plasma events and must withstand high mechanical loads. Based on typical port plugs, this paper presents the conceptual design of the port structures (with emphasis on the supporting system), and the results of analyses performed

Vacuum vessel port structures for ITER-FEAT

Energy Technology Data Exchange (ETDEWEB)

Utin, Yu.; Ioki, K.; Komarov, V.; Krylov, V.; Kuzmin, E.; Labusov, I.; Miki, N.; Onozuka, M.; Rozov, V.; Sannazzaro, G.; Tesini, A.; Yamada, M.; Barthel, Th

2001-11-01

The equatorial and the upper port structures are the most loaded among those of the ITER-FEAT vacuum vessel (VV). For all of these ports, the VV closure plate and the in-port components are integrated into the port plug. The plugs/port structures are affected by plasma events and must withstand high mechanical loads. Based on typical port plugs, this paper presents the conceptual design of the port structures (with emphasis on the supporting system), and the results of analyses performed.

COSIMA-ES-PORT

DEFF Research Database (Denmark)

Barfod, Michael Bruhn; Leleur, Steen

2007-01-01

This article describes the results of the research project – WP3 East-west, Interreg IIIB – concerning the de¬velop¬ment of a new composite decision model, COSIMA-ES-PORT, for the assessment of three pre-feasibility studies situated at the Port of Esbjerg: a road project, a railway project...... and a multimodal terminal. The three studies indicates that a new road connection to the Port of Esbjerg is a very profitable project due to large travel time savings, whereas a new railway connection is not economically viable. However, a new multimodal terminal is also a very profitable project. The COSIMA...

Non-Price Competition in the Port Sector: A Case Study of Ports in Turkey

Directory of Open Access Journals (Sweden)

Soner Esmer

2016-03-01

Full Text Available Although the port sector has been facing increasing competition, there is limited research on how ports compete using non-price competition strategies. There are a few studies on non-price competition in the port sector. However they mainly focus on the marketing aspect. This paper seeks to fill this gap in the literature, especially from a combined marketing-economic perspective. Especially the paper's main objective is to identify the determinants of non-price competition in the port sector and evaluate their effect on various aspects of non-price competition. We start with a general conceptual framework to explain how competition in the sector can be affected by various factors and then propose an analytical framework on non-price competition. The analytical model is then used to support the design of a survey questionnaire. Next, hypothesis tests are conducted using exploratory factor analysis (EFA and structural equation modeling (SEM and data collected from a survey of Turkish ports. Based on the analysis results, the implications for port management and future research are also discussed.

Management of Artisanal Fishing Port: a Case Study on Labuhanhaji Fishing Port, South Aceh Regency, Aceh Province

OpenAIRE

NurJannah, Betri; ', Syaifuddin; Zain, Jonny

2014-01-01

A series survey activity was carried out for evaluating management function atlabuanhaji fishing port, South Aceh regency. This research was emphasis on planning, organizing, action and controlling at management pattern of labuhanhaji fishing port. The facilities of fishing port data and daily activities description of staff at labuhanhaji fishing port was used as additional information and consideration in management of labuhanhaji fishing port. Lack of good management was impact on staff an...

Maximizing port and transportation system productivity by exploring alternative port operation strategies.

Science.gov (United States)

2011-06-01

Seaports are a critical transportation component that supports the nations economy. Many U.S. : ports are now experiencing significant truck congestion at the gate, which decreases the productivity of : ports and truck fleets (e.g. truck wait time...

A review of dry ports

OpenAIRE

Violeta Roso; Kent Lumsden

2010-01-01

The objective of this article is to present the previous research on the dry port concept and to review the world's existing dry ports, that is freight terminals that use the term ‘dry port’ in their name. Therefore, the purpose of this article is to clarify the concept by showing potential discrepancies or agreements between theory and practice. Starting from a literature review on the dry port concept, this article presents a review of existing dry ports in the world. A number of qualitativ...

Analyzing Growth Opportunity of Port from the Resource-based Perspective The Case of Port of Tanjung Pelepas Malaysia

Directory of Open Access Journals (Sweden)

Muhammad Subhan

2008-09-01

Full Text Available Capturing growth opportunity has become a major integral activity of any port to sustain growth and competitive advantage. One of the famous strategies in leveraging sustainable growth and competitive advantage is the resource-based theory application into port strategic management, viewing resources of the port (internal and external and its capabilities as the sources for achieving competitive advantage. In this study, we attempt to identify, exploit, and analyze growth opportunity of a Malaysian port from the perspective of the theory. We analyze the port’s resources in terms of values, uniqueness, inimitability, durability, and substitutability. The result is then compared with its rival ports in the region. This study recognizes that the port has successfully identified and exploited its resources for capturing growth opportunity and competing with other ports in the region. We perceive that the port will sustain its growth and competitive advantage as a major port in the region based on its current performance and rivalry circumstances. This study signifies that the higher the level to which resource-based theory of competitive advantage is applied, the higher and longer the growth and competitive advantage will be achieved by the port.

Monitor portátil de signos vitales con un PDA

OpenAIRE

Rodríguez Salazar, Rita Beatriz

2007-01-01

El monitor portátil de signos vitales facilita el proceso de medición y lleva un registro organizado de los valores medidos. Los signos vitales que se contempla son la temperatura corporal, la presión arterial y la frecuencia cardiaca.Para la medición de estos signos vitales se utilizan los sensores respectivos y se realiza el acondicionamiento de señal. Estas señales son procesadas en un PDA en el que también se visualiza los valores obtenidos en la medición y se registra estos datos si el u...

Port Authority Best Practices

Science.gov (United States)

Best practices for port authorities include near-port community collaboration, anti-idling policies, expanding off-peak hours, development of EMS, developing an emissions inventory, education, electric power and substituting trucking for rail or barge.

US Ports of Entry

Data.gov (United States)

Department of Homeland Security — HSIP Non-Crossing Ports-of-Entry A Port of Entry is any designated place at which a CBP officer is authorized to accept entries of merchandise to collect duties, and...

Starting manufacturing phase of ITER upper ports

Energy Technology Data Exchange (ETDEWEB)

Utin, Yuri, E-mail: yuri.utin@iter.org [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Alekseev, Alexander; Sborchia, Carlo; Choi, Changho; Albin, Vincent; Barabash, Vladimir; Davis, James [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Fabritsiev, Sergey [NTC Sintez, Efremov Inst., 189631 Metallostroy, St. Petersburg (Russian Federation); Giraud, Benoit; Guirao, Julio [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Koenig, Werner [MAN Diesel & Turbo SE, Werftstrasse 17, Deggendorf (Germany); Kedrov, Igor; Kuzmin, Evgeny [NTC Sintez, Efremov Inst., 189631 Metallostroy, St. Petersburg (Russian Federation); Levesy, Bruno; Martinez, Jean-Marc [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Prebeck, Markus [MAN Diesel & Turbo SE, Werftstrasse 17, Deggendorf (Germany); Privalova, Elena [NTC Sintez, Efremov Inst., 189631 Metallostroy, St. Petersburg (Russian Federation); Ranzinger, Franz [MAN Diesel & Turbo SE, Werftstrasse 17, Deggendorf (Germany); Savrukhin, Petr [Russian Federation ITER Domestic Agency, Kurchatov sq.1, 123182 Moscow (Russian Federation); Schiller, Thomas [MAN Diesel & Turbo SE, Werftstrasse 17, Deggendorf (Germany); and others

2015-10-15

Highlights: • The port plugs are attached to the ports with high-strength fasteners. • Tightening of the fasteners via inductive heating was tested. • A concept for the port/plug sealing with metal-type gaskets has progressed. • Manufacturing design of the Upper Ports is in progress. • A full-scale mock-up of double-wall part of the port stub extension is in manufacturing process – acceptable final tolerances are expected. - Abstract: The ITER Vacuum Vessel (VV) features upper, equatorial and lower ports. The upper and regular equatorial ports are occupied by the port plugs. Although the port design has been overall completed in the past, the design of some remaining interfaces was still in progress: in particular, the Sealing Flange package, which includes the high-vacuum seals and the plug fasteners. As the ITER construction phase has started, the procurement of the VV ports has been launched. The VV upper ports will be procured by the Russian Federation Domestic Agency. The main suppliers were selected and the manufacturing design of the first parts is in full progress now. Since the VV is classified at nuclear level N2, the design and manufacture of its components are to be compliant with the French RCC-MR code and regulations for nuclear pressure equipment in France. These regulations make a strong impact to the port design and manufacturing process.

Starting manufacturing phase of ITER upper ports

International Nuclear Information System (INIS)

Utin, Yuri; Alekseev, Alexander; Sborchia, Carlo; Choi, Changho; Albin, Vincent; Barabash, Vladimir; Davis, James; Fabritsiev, Sergey; Giraud, Benoit; Guirao, Julio; Koenig, Werner; Kedrov, Igor; Kuzmin, Evgeny; Levesy, Bruno; Martinez, Jean-Marc; Prebeck, Markus; Privalova, Elena; Ranzinger, Franz; Savrukhin, Petr; Schiller, Thomas

2015-01-01

Highlights: • The port plugs are attached to the ports with high-strength fasteners. • Tightening of the fasteners via inductive heating was tested. • A concept for the port/plug sealing with metal-type gaskets has progressed. • Manufacturing design of the Upper Ports is in progress. • A full-scale mock-up of double-wall part of the port stub extension is in manufacturing process – acceptable final tolerances are expected. - Abstract: The ITER Vacuum Vessel (VV) features upper, equatorial and lower ports. The upper and regular equatorial ports are occupied by the port plugs. Although the port design has been overall completed in the past, the design of some remaining interfaces was still in progress: in particular, the Sealing Flange package, which includes the high-vacuum seals and the plug fasteners. As the ITER construction phase has started, the procurement of the VV ports has been launched. The VV upper ports will be procured by the Russian Federation Domestic Agency. The main suppliers were selected and the manufacturing design of the first parts is in full progress now. Since the VV is classified at nuclear level N2, the design and manufacture of its components are to be compliant with the French RCC-MR code and regulations for nuclear pressure equipment in France. These regulations make a strong impact to the port design and manufacturing process.

Logistics Road map for Smart SeaPorts

Directory of Open Access Journals (Sweden)

Khaled Gaber EL Sakty

2016-12-01

Full Text Available In the digital world, a smart concept became an essential feature for port organizations to serve as intelligent hubs in the world transport networks.  Smart ports are the trend for the future long-term strategies. Henceforth, ports aims at contributing to sustainable growth by establishing the appropriate conditions for the adoption of new management energy models based on low environmental impact and triggering innovation of both technologies and processes. The scope of this paper is to examine three main issues of smart ports; smart port arctic logistics roadmap, smart port challenges and obstacles in arctic port areas, and the criteria and Key Performance Indicators guiding the assessment of ports against this concept. The main purpose is to develop a smart arctic logistics road map for the future.

Dry Port Development: A Systematic Review

Directory of Open Access Journals (Sweden)

Fatimazahra BENTALEB

2015-12-01

Full Text Available Studies on dry ports as nodes in multimodal transport have been expanded to decrease the mounting congestion on seaports. The principal objective of this study is to inspect how dry port researches have been conducted from different perspective. This paper tries to recap the existing researches that aimed to study dry port concept via a systematic review, to present a general overview of the researches on our relevant region and propose a classification for these researches. This paper present a systematic review of dry port that looks to illustrate the progress of researches on this area between 1986 and 2015, collecting researches on dry port concept and analyzing the main characteristics of the dry port development and their contribution to the multimodal transport. The results indicated that most dry port studies considerate the strategic level and concentrate in the Asian continent. Studies regarding other decision levels and continents have to be developed in further researches. Although the existing studies make a contribution in dry port concept, they allow gaps in terms of operational and tactical decision levels considering their limited geographical region.

Interior acoustic cloak

Directory of Open Access Journals (Sweden)

Wael Akl

2014-12-01

Full Text Available Acoustic cloaks have traditionally been intended to externally surround critical objects to render these objects acoustically invisible. However, in this paper, the emphasis is placed on investigating the application of the acoustic cloaks to the interior walls of acoustic cavities in an attempt to minimize the noise levels inside these cavities. In this manner, the acoustic cloaks can serve as a viable and efficient alternative to the conventional passive noise attenuation treatments which are invariably heavy and bulky. The transformation acoustics relationships that govern the operation of this class of interior acoustic cloaks are presented. Physical insights are given to relate these relationships to the reasons behind the effectiveness of the proposed interior acoustic cloaks. Finite element models are presented to demonstrate the characteristics of interior acoustic cloaks used in treating the interior walls of circular and square cavities both in the time and frequency domains. The obtained results emphasize the effectiveness of the proposed interior cloaks in eliminating the reflections of the acoustic waves from the walls of the treated cavities and thereby rendering these cavities acoustically quiet. It is important to note here that the proposed interior acoustic cloaks can find applications in acoustic cavities such as aircraft cabins and auditoriums as well as many other critical applications.

Embedded fiber optic ultrasonic sensors and generators

Science.gov (United States)

Dorighi, John F.; Krishnaswamy, Sridhar; Achenbach, Jan D.

1995-04-01

Ultrasonic sensors and generators based on fiber-optic systems are described. It is shown that intrinsic fiber optic Fabry-Perot ultrasound sensors that are embedded in a structure can be stabilized by actively tuning the laser frequency. The need for this method of stabilization is demonstrated by detecting piezoelectric transducer-generated ultrasonic pulses in the presence of low frequency dynamic strains that are intentionally induced to cause sensor drift. The actively stabilized embedded fiber optic Fabry-Perot sensor is also shown to have sufficient sensitivity to detect ultrasound that is generated in the interior of a structure by means of a high-power optical fiber that pipes energy from a pulsed laser to an embedded generator of ultrasound.

Strategic Planning for Port Development: Improvement of Container Transit from the Iranian Southern Ports Terminals

Directory of Open Access Journals (Sweden)

Homayoun Yousefi

2013-09-01

Full Text Available The author attempts to highlight the significance of the Iranian southern ports development strategy planning which allows for the maximum container transit with minimum resources such as service capacities, human resources, and financial potential in order to expand the Iranian container transit. It should be noted that the strategic objectives, the business strategy and its implementation can be arranged only after the port vision and mission obviously delineated. For the purpose of improving the outcome of the ports operational management, it is recommended to concentrate on new strategies such as exploit of transit corridors for development of the Iranian South Ports. The main part of this paper is dedicated to evaluate the role of container transit from the Iranian south ports terminals from various transport corridors in order to improve Maritime Transport in Iran. The importance of defin¬ing the existing and potential competitors at the Persian Gulf and making a comparison between their and our own strengths and weaknesses is of utmost importance. Sometimes, the real business opportunities and threats are placed beyond one’s own line of indus¬try and business. It is therefore necessary to make a careful analysis of the port environment. After the port competition and environment have been analyzed, it would be possible to initiate the building of the SWOT analysis for the Iranian Southern Container Terminals such as Khoramshahr, Imam Khomani, Busher, Bandar Abbas and Chabahar port which have suitable strategic position as transit base in the region. The SWOT analysis method is therefore applied aiming at defining the weaknesses and strengths of the economic subjects as well as opportunities and threats coming from the environment. The next segment of this paper is dedicated to consider the role of dry ports and the International North-South Transit Corridor for the purpose of improving the Iranian container trade.

Voltage transients in thin-film InSb Hall sensor

Science.gov (United States)

Bardin, Alexey; Ignatjev, Vyacheslav; Orlov, Andrey; Perchenko, Sergey

The work is reached to study temperature transients in thin-film Hall sensors. We experimentally study InSb thin-film Hall sensor. We find transients of voltage with amplitude about 10 μ V on the sensor ports after current switching. We demonstrate by direct measurements that the transients is caused by thermo-e.m.f., and both non-stationarity and heterogeneity of temperature in the film. We find significant asymmetry of temperature field for different direction of the current, which is probably related to Peltier effect. The result can be useful for wide range of scientist who works with switching of high density currents in any thin semiconductor films.

Social Media Usage Patterns in Port Industry: Implications for Port Promotion and Public Relations

Directory of Open Access Journals (Sweden)

Aylin ÇALIŞKAN

2018-03-01

Full Text Available While social media has been penetrating the daily lives of individuals, the businesses have started to develop new strategical approaches for using social media tools, since they understand the importance of this new area. This study aims to take a step on the gap about social media marketing in the port industry. The focused sample is container ports located in Turkey, but to gain more meaningful insights, a comparison is also made with the ports of Los Angeles, Rotterdam, and Antwerp. The post set on Facebook, which covers the 8 months’ period, was analyzed through a social media analytics software, and the most attractive topics and engagement levels were determined. It was found that the most attractive posts of ports with high engagement levels do not include any statement, image, or video about port service, infrastructure and superstructure, investments, or success stories. At the end of the study, suggestions are developed by supporting with real cases for ports’ social media management.

Principles of subcutaneous port placement.

Science.gov (United States)

Gonda, Shaun J; Li, Ruizong

2011-12-01

The introduction of totally implantable subcutaneous devices in the early 1980s provided patients with secure, reliable venous access and also gave them the ability to move more freely and have a more normal lifestyle with these devices in place. The most common totally implantable device used today is the subcutaneous port. These ports consist of an injection port connected to a catheter. Ports provide a number of advantages compared with other venous catheters; the most important is the reduced risk of infection. These devices have significantly lower rates of infection than nontunneled and tunneled catheters. Additional advantages include less frequent irrigation and minimal home care, and they are less prone to environmental or cutaneous contamination when not being accessed. This article will focus on the placement of these ports. Copyright © 2011 Elsevier Inc. All rights reserved.

Adaptive Port Planning under Disruptive Trends with focus on the case of The Port of Kuala Tanjung, Indonesia

OpenAIRE

Prakoso Andre; Taneja Poonam; Velinga Tiedo

2018-01-01

As a national strategic project, the Port of Kuala Tanjung draws significant attention at national and international level. Considering the semi-greenfield nature of the port, the diverse set of stakeholders, and the prevailing disruptive trends in the world port business, a robust first-phase port layout is required to kick-start the project and guarantee the overall sustainability of the port development. The objective of this research is to identify any uncertain or disruptive trends, both...

Grain boundary and grain interior conduction in {gamma}'-Bi{sub 2}MoO{sub 6}

Energy Technology Data Exchange (ETDEWEB)

Vera, C.M.C. [Laboratorio de Peliculas Delgadas, Facultad de Ingenieria, Universidad de Buenos Aires, Paseo Colon 850, 1063 Buenos Aires (Argentina)]. E-mail: cvera@fi.uba.ar; Aragon, R. [Laboratorio de Peliculas Delgadas, Facultad de Ingenieria, Universidad de Buenos Aires, Paseo Colon 850, 1063 Buenos Aires (Argentina); CINSO, CONICET, CITEFA, Lasalle 4397, Villa Martelli, Buenos Aires (Argentina)

2005-07-25

Impedance spectroscopy of fine grained (<10 {mu}m) {gamma}'-Bi{sub 2}MoO{sub 6} samples, in the frequency range of 0.1 Hz-250 kHz, relevant to sensor applications, up to 800 deg. C, has been used to characterize grain boundary and grain interior contributions to conduction. Above 500 deg. C, the grain boundary contribution is no longer rate limiting and conduction is dominated by the grain interior component. The corresponding activation energies are 0.98 eV for grain boundary and 0.73 eV for grain interior components. The weak dependence of conductivity on oxygen partial pressure below 500 deg. C can be attributed to electrode-electrolyte interface phenomena, whereas the robust response to ethanol is commensurate with changes in intrinsic ionic conductivity.

Port entry arrangements

International Nuclear Information System (INIS)

Chicken, J.C.; King, M.A.

1978-01-01

The objective of the paper is to describe the safety scheme port authorities should establish to deal with any contingency that may result from the visit of a nuclear powered ship. The safety scheme should be devised to cover both normal operation and any accident conditions that could arise while the ship is in port. The paper is divided into three parts. The three parts being: background information, general instructions, and emergency procedures. The background information will describe the nature of the hazards a port authority has to be prepared to deal with, and the philosophical basis for a berthing policy. In the part dealing with general instructions the objective of the safety scheme will be described. Also this part will describe the composition of the Port Safety Panel, allocation of responsibilities, passage and berthing arrangements, general safety precautions, records required, and rescue arrangements. In the part dealing with emergency procedures the role of: the Ship's Master, Harbour Authorities, Local Police, and local Health Services are discussed. As an Appendix to the paper a copy of the safety scheme that has been devised for visits of nuclear merchant ships to Southampton is given

Surface-acoustic-wave (SAW) flow sensor

Science.gov (United States)

Joshi, Shrinivas G.

1991-03-01

The use of a surface-acoustic-wave (SAW) device to measure the rate of gas flow is described. A SAW oscillator heated to a suitable temperature above ambient is placed in the path of a flowing gas. Convective cooling caused by the gas flow results in a change in the oscillator frequency. A 73-MHz oscillator fabricated on 128 deg rotated Y-cut lithium niobate substrate and heated to 55 C above ambient shows a frequency variation greater than 142 kHz for flow-rate variation from 0 to 1000 cu cm/min. The output of the sensor can be calibrated to provide a measurement of volume flow rate, pressure differential across channel ports, or mass flow rate. High sensitivity, wide dynamic range, and direct digital output are among the attractive features of this sensor. Theoretical expressions for the sensitivity and response time of the sensor are derived. It is shown that by using ultrasonic Lamb waves propagating in thin membranes, a flow sensor with faster response than a SAW sensor can be realized.

Assesment of port governance in Brazil: a managerial perspective on the port of Santos

OpenAIRE

Almeida, José Eduardo Costa de

2015-01-01

The role of maritime transportation within international trade was drastically revamped during the inception of the globalization process, which enhanced the contribution of ports in world economy as main logistics gateways for global production and trade. As a result, the relationship between ports and governments has changed. Devolution ideologies that had been applied in other industries decades ago were now being considered by governments for the port industry. Many central governments so...

[Clinical retrospective control study of single-port laparoendoscopic and multi-port laparoscopic ovarian cystectomy].

Science.gov (United States)

Liu, X; Wen, M K; Liu, H Y; Sun, D W; Lang, J H; Fan, Q B; Shi, H H

2017-10-25

Objective: To investigate clinical outcomes of laparoendoscopic single-site ovarian cystectomy compared with traditional multi-port laparoscopic ovarian cystectomy. Methods: Data of 81 patients with ovarian cystectomy from January 2016 to May 2017, the single-site group ( n= 40) and the multi-port group ( n= 41) in Peking Union Medical College Hospital were retrospectively collected. The outcomes of single-site and multi-port groups were analyzed and compared, including: postoperative fever, operation time, blood loss, hemoglobin change, surgical complications, postoperative pain score, postoperative analgesic requirements, body image scale and cosmetic score, length of hospital stay, postoperative total cost. Results: No complication was found in two groups. No difference was found in postoperative fever, blood loss, hemoglobin change, postoperative pain score, length of hospital stay, and total cost between the two groups (all P> 0.05). Operation time was (50±20) minutes in single-site group, and (40±15) minutes in multi-port group; postoperative analgesic requirements was 28%(11/40) in single-site group, and 7%(4/41) in multi-port group; cosmetic score was 22.6±2.6 in single-site group, and 17.3±2.6 in multi-port group; body image scale was 5.7±1.2 in single-site group, and 6.2±1.2 in multi-port group; these four clinical parameters were statistical differences (all P< 0.05). Conculsion: Laparoendoscopic single-site ovarian cystectomy is feasible and safe, although it could't relieve the postoperative pian, it do offer a higher cosmetic satisfaction.

Container Traffic In European Ports

Directory of Open Access Journals (Sweden)

Elen Twrdy

2004-03-01

Full Text Available Over the last fifteen years the European transport markethas witnessed a growth of container traffic which today reachesapproximately 50 million TEU per year. From 1997 to 2002,container traffic in the northern European ports increased from14 to 20.6 million TEU per year, in the ports of the westernMedite"anean from 6 to 10 million TEU per year, and in thenorthern Adriatic ports from 0. 69 to 0. 74 million TEU per year.The ports of the northern Adriatic are located in three states(Slovenia, Croatia and Italy with different statuses in relationto the common European market. In addition, different developmentlevels of these states are reflected in different levels ofinternational commercial exchange, the development of the existinginfrastructure and plans for the construction of new infrastructures.However, all three countries share a common goaltoincrease their competitiveness in comparison with the westemEuropean ports.

System аnalysis concession maritime trade ports

Directory of Open Access Journals (Sweden)

Y.V. Shmatock

2015-03-01

Full Text Available The article proves the significance of maritime commercial ports as strategic for the country. The urgency of port concessions to improve transport infrastructure. The definition of ports in terms of system analysis and determination of management port. Outlined the sequence of system analysis concessions maritime trade ports in the table. Selection of qualified managers is based on the concession tender under prescribed conditions. These criteria should be considered when determining the concessionaire. These stages of the concession tender. Meeting the needs of the economy, international trade, public inquiries into transportation of goods is not possible without the efficient operation of maritime trade ports. Only complex technological modernization of maritime trade ports will enable them to take leadership positions. Tree depicted objectives effectively manage commercial sea port. Therefore, initiation of concessions needs to implement measures to achieve the talented and skillful result.

Interior Design.

Science.gov (United States)

Texas Tech Univ., Lubbock. Home Economics Curriculum Center.

This document contains teacher's materials for an eight-unit secondary education vocational home economics course on interior design. The units cover period styles of interiors, furniture and accessories, surface treatments and lighting, appliances and equipment, design and space planning in home and business settings, occupant needs, acquisition…

Oluvil Port Development Project

DEFF Research Database (Denmark)

Frigaard, Peter; Margheritini, Lucia

Oluvil Port Development Project is the first development of a large port infrastructure in the entire eastern coastline of Sri Lanka. The project is supported by the Danish Foreign Ministry. Feasibility studies and detailed design studies were carried out by Lanka Hydraulic Institute Ltd during...... the years 1995 to 2003. The design was reviewed by COWI a/s. Construction of the port was started in 2008. MT Højgaard a/s acted as contractor. The outer breakwaters were constructed as first part of the project. During and after completion of the breakwaters a serious beach erosion and sand accumulation...... has been observed. Severe erosion is seen north of the harbour and some accumulation of sand is seen south of the harbour. On a sandy coastline like the one in Oluvil such erosion problems as observed are very typical. The report: Oluvil Port Development Project: Studies on Beach Erosion written...

Design of Mine Ventilators Monitoring System Based on Wireless Sensor Network

International Nuclear Information System (INIS)

Fu Sheng; Song Haiqiang

2012-01-01

A monitoring system for a mine ventilator is designed based on ZigBee wireless sensor network technology in the paper. The system consists of a sink node, sensor nodes, industrial personal computer and several sensors. Sensor nodes communicate with the sink node through the ZigBee wireless sensor network. The sink node connects with the configuration software on the pc via serial port. The system can collect or calculate vibration, temperature, negative pressure, air volume and other information of the mine ventilator. Meanwhile the system accurately monitors operating condition of the ventilator through these parameters. Especially it provides the most original information for potential faults of the ventilator. Therefore, there is no doubt that it improves the efficiency of fault diagnosis.

Design of Mine Ventilators Monitoring System Based on Wireless Sensor Network

Science.gov (United States)

Fu, Sheng; Song, Haiqiang

2012-05-01

A monitoring system for a mine ventilator is designed based on ZigBee wireless sensor network technology in the paper. The system consists of a sink node, sensor nodes, industrial personal computer and several sensors. Sensor nodes communicate with the sink node through the ZigBee wireless sensor network. The sink node connects with the configuration software on the pc via serial port. The system can collect or calculate vibration, temperature, negative pressure, air volume and other information of the mine ventilator. Meanwhile the system accurately monitors operating condition of the ventilator through these parameters. Especially it provides the most original information for potential faults of the ventilator. Therefore, there is no doubt that it improves the efficiency of fault diagnosis.

COMPETITION BETWEEN CONTAINER PORTS IN THE NORTHERN ADRIATIC

OpenAIRE

Elen Twrdy; Milan Batista

2014-01-01

World trade has changed in the last decade such that container traffic flows are oriented towards more parts of the European continent. The European container port system is not a homogeneous set of ports; instead it consists of several big ports (e.g., Rotterdam, Hamburg, Algeciras...) and a large number of medium and small ports. Northern Adriatic (NA) ports, namely Rijeka, Koper, Trieste, Venice and Ravenna, are small ports. Each of these ports have different development plans but in varyi...

50 CFR 24.12 - Designated ports.

Science.gov (United States)

2010-10-01

...) The U.S. Department of Agriculture ports at Hilo, Hawaii, and Chicago, Illinois, are designated ports..., Florida Atlanta, Georgia Savannah, Georgia Agana, Guam Hilo, Hawaii Honolulu, Hawaii Wailuku, Maui, Hawaii... Orlando, Florida Honolulu, Hawaii New Orleans, Louisiana Hoboken, New Jersey (Port of New York) Jamaica...

Perancangan Miniatur Traffic Light Dengan Mempergunakan Pengendali Port Paralel

OpenAIRE

Eka Wahyudi; Desi Permanasari

2012-01-01

Port paralel tentunya sudah tidak asing lagi dalam dunia komputer. Hal tersebut disebabkan karena port paralel merupakan sarana komunikasi yang terdapat pada Personal Computer (PC). Dengan memanfaatkan port tersebut, saat ini komputer juga dapat dipergunakan untuk keperluan pengontrolan/pengendalian rangkaian listrik dengan memanfaatkan port paralel (port printer). Port paralel memiliki kecepatan transfer data yang lebih cepat apabila dibandingkan dengan port serial, maka dari itu port parale...

The Development of the Regional Sea Port Infrastructure on the Basis of Dry Port

Directory of Open Access Journals (Sweden)

Aleksandr Nelevich Rakhmangulov

2016-09-01

Full Text Available This article contributes to the solution of the relevant problem of the seaport infrastructure development for the purpose of increasing the cargo turnover in the regions of seaport location as well as to improve the quality of freight traffic on the basis of the creation of container hinterlands — dry ports. The options of dry ports as the potentially effective solution to increase the cargo turnover of existing seaports, improve the timeliness of freight transportation and overcome the environmental problems of the regions of seaport location are shown. This work analyzes the transport infrastructure of the region, the cargo turnover of major Russian sea and dry ports as well as the experience of creating dry ports in the Russian Federation and abroad. The authors propose the system of parameters for dry ports, which are recommended for the assessment of seaport infrastructure development scenarios on the stage of strategic planning. The authors have developed the approach of optimal values determination of the main parameters of dry ports by simulation modeling method. The features of construction and research of the simulation models of system “seaport — dry port” in programming software AnyLogic are considered. The results of modeling experiments with a developed simulation model are provided. This model is aimed to assess the maximum estimated capacity of the existing seaport in the conditions of the increasing irregularity of cargo traffic, and also to determine the optimum parameters of the constructed «dry port». The obtained dependencies as a result of modeling experiments prove the adequacy of the selected main parameters of dry ports for the effective evaluation of the scenarios of the strengthening of carrying and estimated capacity of existing seaports on the stage of strategic planning. The article shows that the methodology of this research can be used by the investors and public authorities as grounds for a decision on

The annealing effects on irradiated SiC piezo resistive pressure sensor

International Nuclear Information System (INIS)

Almaz, E.; Blue, T. E.; Zhang, P.

2009-01-01

The effects of temperature on annealing of Silicon Carbide (SiC) piezo resistive pressure sensor which was broken after high fluence neutron irradiation, were investigated. Previously, SiC piezo resistive sensor irradiated with gamma ray and fast neutron in the Co-60 gamma-ray irradiator and Beam Port 1 (BP1) and Auxiliary Irradiation Facility (AIF) at the Ohio State University Nuclear Reactor Laboratory (OSUNRL) respectively. The Annealing temperatures were tested up to 400 C. The Pressure-Output voltage results showed recovery after annealing process on SiC piezo resistive pressure sensor. The bridge resistances of the SiC pressure sensor stayed at the same level up to 300 C. After 400 C annealing, the resistance values changed dramatically.

Hub Status and Indexation of Container Ports

Directory of Open Access Journals (Sweden)

Yong-An Park

2015-06-01

This study develops two sub-indexes of port classification and capacity, and combines cases of these two sub-indexes into various types in order to find a proper port hub index. The paper demonstrates how different types of port hub index are useful measurements for evaluating outputs and inputs of container ports. In a case analysis we show that the indexes of period variables and lagged variables have more explanatory power with regard to changes of port throughputs and high correlation with inputs.

PORT SECURITY-Threats and Vulnerabilities

OpenAIRE

Kusi, Bernard

2015-01-01

The main objective of this thesis is to identify the threats and the vulnerabilities concerning Takoradi port, and finally recommend measure to overcome the identified threats and vul-nerabilities. Various categories of potential threats and vulnerabilities have been studied throughout the literature review. However, because each port presents a unique sets of threats and vulnerabilities, there was a need to look critically into how Takoradi port operations are being conducted in other to ide...

DEA Window Analysis for Measuring Port Efficiencies in Serbia

Directory of Open Access Journals (Sweden)

Danijela Pjevčević

2012-01-01

Full Text Available The aim of the paper is to apply Data Envelopment Analysis (DEA method in measuring and analyzing the efficiencies of ports on the river Danube. DEA window analysis is used to determine the efficiency of ports and to observe the possibility of changes in the port efficiency over time. A study is conducted to evaluate the efficiencies of ports on the territory of Serbia in order to identify the sources of inefficiencies and formulate proposals for improving the services of those ports and their operations through a four-year window analysis with port efficiency trends and average efficiencies. The progress is made in the measurement of port efficiency in relation to port productive activities - total area of warehouses, quay length, number of cranes and port throughput, for the Serbian river ports. Keywords: river ports, total area of warehouses, quay length, number of cranes, port throughput, port efficiency, DEA window analysis

Development of an automated remote inspection system for the interior of the primary containment vessel of a nuclear power plant

International Nuclear Information System (INIS)

Senoo, Makoto; Yoshida, Tomiharu; Omote, Tatsuyuki; Tanaka, Keiji; Koga, Kazunori

1996-01-01

An automated remote inspection system has been developed for the interior of the primary containment vessel of a nuclear power plant. This system consists of an inspection robot and an operator's console. The inspection robot travels along a monorail provided in the interior of the primary containment vessel. The operator's console is located in the central control room of the power plant. We have made efforts to downsize the robot and automate the inspection and monitoring machinery. As for downsizing the robot, a 152 mm wide, 290 mm high cross-sectional area and 15 kg weight can be realized using commercially available small sensors and rearranging the parts in those sensors. As for automating the inspection and monitoring, several monitoring functions are developed using image processing, frequency analysis and other techniques applied to signals from sensors such as an ITV camera, an infrared camera and a microphone, which are mounted on the robot. Endurance tests show resistance of the robot to radiational and thermal conditions is adequate for actual use in actual power plants. (author)

Multi-functional use of port areas

NARCIS (Netherlands)

Ros, R.; Taneja, P.; Vellinga, T.

2012-01-01

The core business of a port is handling vessels and cargo. In addition a landlord Port Authority invests in development of port areas. However, in view of the new trends such as stakeholders interests related to environment and sustainability, it is can be wise to reexamine the business portfolio

Notch filters for port-Hamiltonian systems

NARCIS (Netherlands)

Dirksz, D.A.; Scherpen, J.M.A.; van der Schaft, A.J.; Steinbuch, M.

2012-01-01

In this paper a standard notch filter is modeled in the port-Hamiltonian framework. By having such a port-Hamiltonian description it is proven that the notch filter is a passive system. The notch filter can then be interconnected with another (nonlinear) port-Hamiltonian system, while preserving the

Port-contact systems in bilateral telemanipulation

NARCIS (Netherlands)

Secchi, C; Stramigioli, Stefano; Fantuzzi, C.

2007-01-01

In this paper we develop one of the first control applications of the recently proposed port-contact framework. We show how it is possible to model and control a bilateral telemanipulation system using port-contact systems and we develop a port-contact impedance controller that allows to impose a

A Nanocoaxial-Based Electrochemical Sensor for the Detection of Cholera Toxin

Science.gov (United States)

Archibald, Michelle; Rizal, Binod; Connolly, Timothy; Burns, Michael J.; Naughton, Michael J.; Chiles, Thomas C.; Biology; Physics Collaboration

We report a nanocoax-based electrochemical sensor for the detection of bacterial toxins using an electrochemical enzyme-linked immunosorbent assay (ELISA) and differential pulse voltammetry (DPV). The device architecture is composed of vertically-oriented, nanoscale coaxial electrodes, with coax cores and shields serving as integrated working and counter electrodes, respectively. Proof-of-concept was demonstrated for the detection of cholera toxin (CT), with a linear dynamic range of detection was 10 ng/ml - 1 µg/ml, and a limit of detection (LOD) of 2 ng/ml. This level of sensitivity is comparable to the standard optical ELISA used widely in clinical applications. The nanocoax array thus matches the detection profile of the standard ELISA while providing a simple electrochemical readout and a miniaturized platform with multiplexing capabilities, toward point-of-care (POC) implementation. In addition, next generation nanocoax devices with extended cores are currently under development, which would provide a POC platform amenable for biofunctionalization of ELISA receptor proteins directly onto the device. This work was supported by the National Institutes of Health (National Cancer Institute Award No. CA137681 and National Institute of Allergy and Infectious Diseases Award No. AI100216).

Port Harcourt Medical Journal

African Journals Online (AJOL)

Port Harcourt Medical Journal's objectives are to disseminate medical information from the College of Health Sciences, University of Port Harcourt and the rest of the national and international medical community; act as a medium for the articulation of research and findings from same as well as proceedings of medical ...

Perancangan Miniatur Traffic Light Dengan Mempergunakan Pengendali Port Paralel

Directory of Open Access Journals (Sweden)

Eka Wahyudi

2012-05-01

Full Text Available Port paralel tentunya sudah tidak asing lagi dalam dunia komputer. Hal tersebut disebabkan karena port paralel merupakan sarana komunikasi yang terdapat pada Personal Computer (PC. Dengan memanfaatkan port tersebut, saat ini komputer juga dapat dipergunakan untuk keperluan pengontrolan/pengendalian rangkaian listrik dengan memanfaatkan port paralel (port printer. Port paralel memiliki kecepatan transfer data yang lebih cepat apabila dibandingkan dengan port serial, maka dari itu port paralel lebih banyak dipergunakan untuk pengendalian nyala lampu (LED. Dengan memanfaatkan bantuan software Saraf Listrik versi 1.01, maka port paralel dapat menjadi alternatif baru untuk pengendalian traffic light.

Port Card Module

International Nuclear Information System (INIS)

Utes, M.

1994-01-01

The Port Card will be one link in the data acquisition system for the D0 Silicon Vertex Detector. This system consists of the following parts, starting at the detector: Silicon strip detectors are mounted in a spaceframe and wire-bonded to custom bare-die integrated circuits (SVX-II chips) that digitize the charge collected by the strips. The 128-channel chips are mounted on a High-Density Interconnect (HDI) that consists of a small flex circuit that routes control signals and eight data bits for each of three to ten chips onto a common data bus. A cable then routes this bus approximately thirty feet out from the detector to the Port Card. The Port Card houses a commercial chipset that serializes the data in real time and converts the signal into laser light impulses that are then transmitted through a multi-mode optical fiber about 150 feet to a Silicon Acquisition and Readout board (SAR). Here, the data is transformed back to parallel electrical signals that are stored in one of several banks of FIFO memories. The FIFOs place their data onto the VME backplane to a VME Buffer Driver (VBD) which stores the event data in buffers for eventual readout over a thirty-two signal ribbon cable to the Level Two Computers and subsequent tape storage. Control and sequencing of the whole operation starts with the Silicon Acquisition/Readout Controller (SARC) working in tandem with the D0 Clock System. The SARC resides in the same VME crate as the SARs, and transforms signals from the Trigger System into control codes distributed to the various Port Cards via optical fibers operating at 53 Mb/s. It is through these control codes that data taking operations such as data-acquisition, digitization, readout, and various resets can be carried out. The Port Card receives the control codes and manipulates the SVX-II chips in the proper way to effect proper data taking. There will be a total of about 700,000 channels, which translates into about 5580 SVX-II chips, 66 to 100 Port Cards

TRENDS IN CONTEMPORARY PORT SERVICES MARKETS

Directory of Open Access Journals (Sweden)

Hanna Klimek

2014-12-01

Full Text Available This article describes the issues associated with functioning of contemporary seaport services markets. The growth of international supply chains, technical progress and the integration processes in shipping, growth of containerization, increasing competition in the seaport services markets and environmental protection regulations make it necessary for port service providers to adapt to the changing expectations and requirements of their customers, both shippers and, especially maritime, carriers. Thus, the activities they undertake are associated with making investments to ensure an adequate capacity to handle cargo, passengers and means of transport, required quality of service, but also with appropriate organization of port supply centres and lead to an improvement of their competitiveness. Both the factors associated with the external and internal environment of seaports affect the changes in the relationship between the supply and demand on port services markets. Contemporary port services markets are characterized by certain phenomena which can be a sign of their adaptation and development. The aim of this article is to present the essence of the port services market and its relationship with the environment, which subject to rapid and significant changes, creates new conditions for the operation of port supply centres and the entire port services market.

Processamento radiográfico - câmara escura portátil: relação entre filtro de luz e densidade de base + véu

Directory of Open Access Journals (Sweden)

TAMBURÚS José Roberto

1999-01-01

Full Text Available O objetivo desta pesquisa foi avaliar o efeito sobre a densidade de base + véu de filmes radiográficos, decorrente do uso da luz filtrada pelo polímero acrílico utilizado nas câmaras portáteis para processamento radiográfico. Filmes Kodak Ultra-speed e Ektaspeed Plus foram colocados no interior de uma câmara desse tipo e submetidos durante cinco minutos às condições de iluminação natural e artificial em que elas são rotineiramente utilizadas. Depois disso, os filmes foram processados pelo método temperatura-tempo em câmara escura convencional, juntamente com filmes dos mesmos grupos de sensibilidade que serviram como controle. Os valores densitométricos obtidos das amostras dos filmes foram analisados pelo teste de Mann-Whitney que indicou ao nível de 1% de significância, que os filmes submetidos às condições da câmara portátil apresentaram densidades de base + véu maiores em relação aos grupos controle. Os resultados mostraram que o filme Ektaspeed Plus apresentou valores maiores de densidade de base + véu em comparação com o filme Ultra-speed e que, embora o acrílico filtre a luz de forma similar ao filtro Kodak GBX 2, a maior intensidade de luz no interior da câmara escura portátil ocasionou o aumento na densidade de base + véu.

US Army Corps of Engineers Ports, Geographic WGS84, BTS (2006) [usace_port_BTS_2006

Data.gov (United States)

Louisiana Geographic Information Center — Contains physical information on commercial facilities at the principal U.S. Coastal, Great Lakes and Inland Ports. The data consists of listings of port area's...

The Challenges of Malaysian Dry Ports Development

Directory of Open Access Journals (Sweden)

Jagan Jeevan

2015-03-01

Full Text Available This paper examines the functions and challenges of dry ports development in Malaysia through 11 face-to-face interviews with dry port stakeholders. The findings reveal that Malaysian dry ports are developed to accelerate national and international business, to activate intermodalism in the nation, to promote regional economic development and to enhance seaport competitiveness. Malaysian dry ports perform the function of transport and logistics, information processing, seaports and value-added services. Challenges facing Malaysian dry ports include insufficient railway tracks, unorganized container planning on the rail deck, highly dependent on single mode of transportation, poor recognition from the seaport community, and competition from localized seaports. This paper further indicates strategies for coping with these challenges and identifies future opportunities for Malaysian dry ports development.

Sensor Network Motes:

DEFF Research Database (Denmark)

Leopold, Martin

requirements on price and performance, and shows great potential for using sensor networks. Throughout the project we let the application requirements guide our design choices, leading us to push the technologies further to meet the specific goal of the application. In this dissertation, we attack two key...... areas related to the design of this solution. We found the current state of the art within performance evaluation to be inadequate and that the moving to the next generation platforms is being held back by practical issues in porting existing software. We have taken a pragmatic, experimental approach...

Benchmark dynamics in the environmental performance of ports.

Science.gov (United States)

Puig, Martí; Michail, Antonis; Wooldridge, Chris; Darbra, Rosa Mari

2017-08-15

This paper analyses the 2016 environmental benchmark performance of the port sector, based on a wide representation of EcoPorts members. This is the fifth time that this study has been conducted as an initiative of the European Sea Ports Organisation (ESPO). The data and results are derived from the Self-Diagnosis Method (SDM), a concise checklist against which port managers can self-assess the environmental management of their port in relation to the performance of the EcoPorts membership. The SDM tool was developed in the framework of the ECOPORTS project (2002-2005) and it is managed by ESPO. A total number of 91 ports from 20 different European Maritime States contributed to this evaluation. The main results are that air quality remains as the top environmental priority of the respondent ports, followed by energy consumption and noise. In terms of environmental management, the study confirms that key components are commonly implemented in the majority of European ports. 94% of contributing ports have a designated environmental manager, 92% own an environmental policy and 82% implement an environmental monitoring program. Waste is identified as the most monitored issue in ports (80%), followed by energy consumption (73%) and water quality (70%). Copyright © 2017 Elsevier Ltd. All rights reserved.

[Single-port laparoscopic cholecystectomy: advantages and disadvantages].

Science.gov (United States)

Alekberzade, A V; Lipnitsky, E M; Krylov, N N; Sundukov, I V; Badalov, D A

2016-01-01

To analyze the outcomes of single-port laparoscopic cholecystectomy. Early and long-term postoperative period has been analyzed in 240 patients who underwent laparoscopic cholecystectomy (LCE) including 120 cases of single-port technique and 120 cases of four-port technique. Both groups were compared in surgical time, pain syndrome severity (visual analog scale), need for analgesics, postoperative complications, hospital-stay, daily activity recovery and return to physical work, patients' satisfaction of surgical results and their aesthetic effect. It was revealed that single-port LCE is associated with lower severity of postoperative pain, quick recovery of daily activity and return to physical work, high satisfaction of surgical results and their aesthetic effect compared with four-port LCE. Disadvantages of single-port LCE include longer duration of surgery, high incidence of postoperative umbilical hernia. However hernia was predominantly observed during the period of surgical technique development. Further studies to standardize, evaluate the safety and benefits of single-port LCE are necessary.

The Practice of Guangzhou Port Planning Environmental Impact Assessment

Science.gov (United States)

Wang, Ning; Zhao, Junjie; Shou, Youping; Qiao, Jianzhe; Dong, Shipei; Zhang, Lu

2018-01-01

In this paper, the effects of the implementation of Guangzhou port plan were analyzed from hydrological condition, water environment and ecological environment. Regional water environmental carrying capacity was analyzed. Guangzhou port is a main port in the coast of China, it is an important port of foreign trade in south China, it is an important port for energy supplies and raw materials in Guangdong province [1]. With the shipping channel condition improvement and the construction of large specialized container port area, Guangzhou port will gradually become trunk line port of container transport in south China.

The radiation analyses of ITER lower ports

International Nuclear Information System (INIS)

Petrizzi, L.; Brolatti, G.; Martin, A.; Loughlin, M.; Moro, F.; Villari, R.

2010-01-01

The ITER Vacuum Vessel has upper, equatorial, and lower ports used for equipment installation, diagnostics, heating and current drive systems, cryo-vacuum pumping, and access inside the vessel for maintenance. At the level of the divertor, the nine lower ports for remote handling, cryo-vacuum pumping and diagnostic are inclined downwards and toroidally located each every 40 o . The cryopump port has additionally a branch to allocate a second cryopump. The ports, as openings in the Vacuum Vessel, permit radiation streaming out of the vessel which affects the heating in the components in the outer regions of the machine inside and outside the ports. Safety concerns are also raised with respect to the dose after shutdown at the cryostat behind the ports: in such zones the radiation dose level must be kept below the regulatory limit to allow personnel access for maintenance purposes. Neutronic analyses have been required to qualify the ITER project related to the lower ports. A 3-D model was used to take into account full details of the ports and the lower machine surroundings. MCNP version 5 1.40 has been used with the FENDL 2.1 nuclear data library. The ITER 40 o model distributed by the ITER Organization was developed in the lower part to include the relevant details. The results of a first analysis, focused on cryopump system only, were recently published. In this paper more complete data on the cryopump port and analysis for the remote handling port and the diagnostic rack are presented; the results of both analyses give a complete map of the radiation loads in the outer divertor ports. Nuclear heating, dpa, tritium production, and dose rates after shutdown are provided and the implications for the design are discussed.

Voltage transients in thin-film InSb Hall sensor

Directory of Open Access Journals (Sweden)

Alexey Bardin

Full Text Available The work is reached to study temperature transients in thin-film Hall sensors. We experimentally study InSb thin-film Hall sensor. We find transients of voltage with amplitude about 10 μV on the sensor ports after current switching. We demonstrate by direct measurements that the transients is caused by thermo-e.m.f., and both non-stationarity and heterogeneity of temperature in the film. We find significant asymmetry of temperature field for different direction of the current, which is probably related to Peltier effect. The result can be useful for wide range of scientist who works with switching of high density currents in any thin semiconductor films. 2000 MSC: 41A05, 41A10, 65D05, 65D17, Keywords: Thin-films, Semiconductors, Hall sensor, InSb, thermo-e.m.f.

Adaptive Port Planning under Disruptive Trends with focus on the case of the Port of Kuala Tanjung, Indonesia

NARCIS (Netherlands)

Taneja, P.; Velinga, Tiedo

2018-01-01

As a national strategic project, the Port of Kuala Tanjung draws significant attention at national and international level. Considering the semi-greenfield nature of the port, the diverse set of stakeholders, and the prevailing disruptive trends in the world port business, a robust first-phase

Interior Design in Architectural Education

Science.gov (United States)

Gurel, Meltem O.; Potthoff, Joy K.

2006-01-01

The domain of interiors constitutes a point of tension between practicing architects and interior designers. Design of interior spaces is a significant part of architectural profession. Yet, to what extent does architectural education keep pace with changing demands in rendering topics that are identified as pertinent to the design of interiors?…

Cyber security in ports: Business as usual

OpenAIRE

Moerel, Lokke; Dezeure, Freddy

2017-01-01

Our paper summarizes the risks and provides concrete and pragmatic proposals to increase substantially the cyber maturity and resilience in the ports by organizing training and awareness raising, fostering cooperation and information exchange both between the stakeholders in the ports and across the ports and integrating the cyber risk into the physical security risk management processes and structures already in place within the ports. This also involves a higher degree of oversight by the P...

Slewing Port Jib Cranes

Directory of Open Access Journals (Sweden)

Boris Visočnik

2002-09-01

Full Text Available The paper presents slewing port cra11es with a luffing jib.The advantages of slewing port jib cranes are high lifting capacities,high speeds of re-loading and excellent mobility since theyare capable of load lifting, travelling, luffing and slewing. Thepaper gives a detailed description of their characteristics suchas the highest reached load-canying capacities, speeds of motionand accelerations. It also presents the crane assembly,driving mechanisms, loads and load cases, transport by shipsand testing of lifting capacity. As a practical example the paperpresents the slewing port jib crane with the capacity of25!15!5 tat a 27/37/40 m radius made by the Slovenian companyMetalna Maribor for the shipyard 3. Maj, Rijeka, Croatia.

Research on variable swirl intake port for high-speed multivalve DI diesel engine. Effects of port configuration on flow characteristics and swirl generation capacity; 4 ben kogata kosoku DI diesel engine no kahen swirl kyuki port ni kansuru kenkyu. Kyuki port haichi ga ryudo tokusei to swirl seino ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Kawashima, J; Ogawa, H; Tsuru, Y [Nissan Motor Co. Ltd., Tokyo (Japan)

1997-10-01

In our previous papers, the variable swirl intake port system which can control a wide swirl ratio range (from 4 to 10) was described. This system consisted of two separate intake ports, one of them has a flow control valve for changing the swirl ratio. In this type of variable swirl system, some variations of port combination, port shape, and position can be designed. In this paper, the intake flow characteristics of various port combinations were analyzed on the basis of a steady-state air flow test and 3-dimensional computations. The results indicate that the total performance of the twin ports can be estimated from that of a single port in any kind of port combination. Some difference in flow patterns were found in a variety of port combinations even if each swirl ratio is similar. The selected port combinations in our previous study are good for a wide swirl control range. 11 refs., 9 figs., 1 tab.

CCD linear image sensor ILX511 arrangment for a technical spectrometer

Czech Academy of Sciences Publication Activity Database

Bartoněk, L.; Keprt, Jiří; Vlček, Martin

2003-01-01

Roč. 33, 2-3 (2003), s. 548-553 ISSN 0078-5466 Institutional research plan: CEZ:AV0Z1010921 Keywords : CCD linear sensor ILX511 * enhanced parallel port (EPP able IEEE1284) * A/D converter AD9280 Subject RIV: BH - Optics, Masers, Lasers Impact factor: 0.221, year: 2003

Two-port robotic hysterectomy: a novel approach.

Science.gov (United States)

Moawad, Gaby N; Tyan, Paul; Khalil, Elias D Abi

2018-03-24

The objective of the study was to demonstrate a novel technique for two-port robotic hysterectomy with a particular focus on the challenging portions of the procedure. The study is designed as a technical video, showing step-by-step a two-port robotic hysterectomy approach (Canadian Task Force classification level III). IRB approval was not required for this study. The benefits of minimally invasive surgery for gynecological pathology have been clearly documented in multiple studies. Patients had fewer medical and surgical complications postoperatively, better cosmesis and quality of life. Most gynecological surgeons require 3-5 ports for the standard gynecological procedure. Even though the minimally invasive multiport system provides an excellent safety profile, multiple incisions are associated with a greater risk for morbidity including infection, pain, and hernia. In the past decade, various new methods have emerged to minimize the number of ports used in gynecological surgery. The interventions employed were a two-port robotic hysterectomy, using a camera port plus one robotic arm, with a focus on salpingectomy and cuff closure. We describe a transvaginal and a transabdominal approach for salpingectomy and a novel method for cuff closure. The transvaginal and transabdominal techniques for salpingectomy for two-port robotic-assisted hysterectomy provide excellent tension and exposure for a safe procedure without the need for an extra port. We also describe a transvaginal technique to place the vaginal cuff on tension during closure. With the necessary set of skills on a carefully chosen patient, two-port robotic-assisted total laparoscopic hysterectomy is a feasible procedure.

[Subcutaneous implantation type central venous port management in patients with malignant tumors effect of different antiseptic agents on central venous port-related infection].

Science.gov (United States)

Sato, Junya; Kumagai, Masumi; Kato, Kenichi; Akahane, Akio; Suzuki, Michiko; Kashiwaba, Masahiro; Sone, Miyuki; Kudo, Kenzo

2014-08-01

Subcutaneous implantation type central venous ports(CV ports)are used in chemotherapy. Here, we prospectively examined the frequency of CV port-related infections when the disinfectant was changed from 10% povidone iodine to 1% chlorhexidine ethanol or 70% ethanol. The subjects were patients with malignant tumors, who had newly been implanted with CV ports. We examined CV port-related infections at 1 week after CV port implantation and every 2 weeks thereafter, following sterilization upon insertion of a Huber needle to the CV port. CV port evulsion due to CV port-related infection was noted in 3 patients(4.8%)in whom 15%chlorhexidine ethanol was used(n=62)and in 2 patients(3.3%)in whom 70% ethanol was used(n=60). Infection rates per 1,000 days of CV port use were 1.48% and 1.01%, respectively. Thus, the outcomes of sterilization using 1% chlorhexidine ethanol and 70% ethanol did not differ significantly from those on using 10% povidone iodine for sterilization, based on preliminary results at our institution(3 of 59 patients[5.1%]had port evulsion due to CV port-related infection and the infection rate per 1,000 days of CV port use was 1.47%, Akahane et al, 2012). Chlorhexidine ethanol and ethanol are very convenient to use because they dry quickly and do not need discoloration. Accordingly, chlorhexidine ethanol and ethanol might be useful in CV port management.

3D Modeling of Interior Building Environments and Objects from Noisy Sensor Suites

Science.gov (United States)

2015-05-14

Even though I moved to the other side of the country, they have always been supportive. My Dad , David Turner, has not only been my role model of an...model [10, 23–25]. Models with flat regions or sharp corners where the curvature approaches zero or infinity can become degenerate or have poor ...quality. Since building models are composed almost entirely of such areas, these techniques are not appropriate. Models of building interiors are rich with

Systems theory of interconnected port contact systems

NARCIS (Netherlands)

Eberard, D.; Maschke, B.M.; Schaft, A.J. van der

2005-01-01

Port-based network modeling of a large class of complex physical systems leads to dynamical systems known as port-Hamiltonian systems. The key ingredient of any port-Hamiltonian system is a power-conserving interconnection structure (mathematically formalized by the geometric notion of a Dirac

Ports and Terminals : Planning and Functional Design

NARCIS (Netherlands)

Groenveld, R.; Velsink, H.

1993-01-01

1. Maritime transport, means and commodities 3. Principles of integrated port planning 4. Planning and design of a port's water areas 5. Port terminals - introduction 6. Conventional general cargo terminals 7. Container terminals 8. Oil & liquid gas terminals 9. Dry bulk cargo terminals 10. Fishery

Conservative systems with ports on contact manifolds

NARCIS (Netherlands)

Eberard, D.; Maschke, B.M.; van der Schaft, Arjan; Piztek, P.

In this paper we propose an extension of port Hamiltonian systems, called conservative systems with ports, which encompass systems arising from the Irreversible Thermodynamics. Firstly we lift a port Hamiltonian system from its state space manifold to the thermodynamic phase space to a contact

Single port VATS: recent developments in Asia.

Science.gov (United States)

Yu, Peter S Y; Capili, Freddie; Ng, Calvin S H

2016-03-01

Single port video-assisted thoracic surgery (VATS) is the most recent evolution in minimally invasive thoracic surgery. With increasing global popularity, the single port VATS approach has been adopted by experienced thoracic surgeons in many Asian countries. From initial experience of single port VATS lobectomy to the more complex sleeve resection procedures now forming part of daily practice in some Asia institutes, the region has been the proving ground for single port VATS approaches' feasibility and safety. In addition, certain technical refinements in single port VATS lung resection and lymph node dissection have also sprung from Asia. Novel equipment designed to facilitate single port VATS allowing further reduce access trauma are being realized by the partnership between surgeons and the industries. Advanced thoracoscopes and staplers that are narrower and more maneuverable are particularly important in the smaller habitus of patients from Asia. These and similar new generation equipment are being applied to single port VATS in novel ways. As dedicated thoracic surgeons in the region continue to striving for excellence, innovative ideas in single incision access including subxiphoid and embryonic natural-orifice transluminal endoscopic surgery (e-NOTES) have been explored. Adjunct techniques and technology used in association with single port VATS such as non-intubated surgery, hybrid operating room image guidance and electromagnetic navigational bronchoscopy are all in rapid development in Asia.

Dual-port distal gastrectomy for the early gastric cancer

OpenAIRE

Kashiwagi, Hiroyuki; Kumagai, Kenta; Monma, Eiji; Nozue, Mutsumi

2014-01-01

Background Although recent trends in laparoscopic procedures have been toward minimizing the number of incisions, four or five ports are normally required to complete laparoscopic gastrectomy because of the complexity of this procedure. Multi-channel ports, such as the SILS port (Covidien, JAPAN), are now available and are crucial for performing single-incision laparoscopic surgery (SILS) or reduced port surgery (RPS). We carried out reduced port distal gastrectomy (RPDG) using a dual-port me...

Analysis of laparoscopic port site complications: A descriptive study.

Science.gov (United States)

Karthik, Somu; Augustine, Alfred Joseph; Shibumon, Mundunadackal Madhavan; Pai, Manohar Varadaraya

2013-04-01

The rate of port site complications following conventional laparoscopic surgery is about 21 per 100,000 cases. It has shown a proportional rise with increase in the size of the port site incision and trocar. Although rare, complications that occur at the port site include infection, bleeding, and port site hernia. To determine the morbidity associated with ports at the site of their insertion in laparoscopic surgery and to identify risk factors for complications. Prospective descriptive study. In the present descriptive study, a total of 570 patients who underwent laparoscopic surgeries for various ailments between August 2009 and July 2011 at our institute were observed for port site complications prospectively and the complications were reviewed. Descriptive statistical analysis was carried out in the present study. The statistical software, namely, SPSS 15.0 was used for the analysis of the data. Of the 570 patients undergoing laparoscopic surgery, 17 (3%) had developed complications specifically related to the port site during a minimum follow-up of three months; port site infection (PSI) was the most frequent (n = 10, 1.8%), followed by port site bleeding (n = 4, 0.7%), omentum-related complications (n = 2; 0.35%), and port site metastasis (n = 1, 0.175%). Laparoscopic surgeries are associated with minimal port site complications. Complications are related to the increased number of ports. Umbilical port involvement is the commonest. Most complications are manageable with minimal morbidity, and can be further minimized with meticulous surgical technique during entry and exit.

Challenges and Strategies of Abidjan Port-Hinterland Connectivity

Directory of Open Access Journals (Sweden)

Gamassa Pascal Kany Prud’ome

2017-01-01

Full Text Available Abidjan port-hinterland is composed of three countries which include Ivory Coast, Mali and Burkina Faso. The fast economic growth of the above countries resulted to a greater demand for the foreign goods from their population, causing a congestion problem at Abidjan port. Because of this problem, the connectivity movement between the port and its hinterland has considerably slowed down. In this article a qualitative methodology is used to analyse the Abidjan port-hinterland connectivity. The constant delays of the train services, the road congestion and the lack of coordination and communication between Abidjan port and its hinterland customers are the main presented challenges. The results of this research demonstrate that the poor quality roads and railways and the lack of a new dry port in Ivory Coast greatly affects the fluidity of the Abidjan port-hinterland connectivity. This article suggests some strategies on how to solve the current challenges and will be helpful in deciding on how the Abidjan port should be developed better and improve its connectivity with its hinterland.

The impact of an emerging port on the carbon dioxide emissions of inland container transport: An empirical study of Taipei port

International Nuclear Information System (INIS)

Liao, C.-H.; Tseng, P.-H.; Cullinane, Kevin; Lu, C.-S.

2010-01-01

This study analyzes the changes in carbon dioxide (CO 2 ) emissions resulting from the movement of containers from established ports through the emerging port of Taipei in Northern Taiwan. An activity-based emissions model is used to estimate the CO 2 emissions of container transport under four scenarios where there are switches of market share from existing ports to the emerging port. The results show that there are greater reductions in CO 2 when transhipment routes are changed from the ports of Kaohsiung, Taichung and Keelung to the emerging port of Taipei. The paper concludes that the analytical approach adopted in the paper can help decision-makers understand potential CO 2 emissions reduction strategies in the route selection of inland container transportation and such consideration should provide a broader and more meaningful basis for the socio-economic evaluation of port investment projects.

Process and overview of diagnostics integration in ITER ports

International Nuclear Information System (INIS)

Drevon, J.M.; Walsh, M.; Andrew, P.; Barnsley, R.; Bertalot, L.; Bock, M. de; Bora, D.; Bouhamou, R.; Direz, M.F.; Encheva, A.; Fang, T.; Feder, R.; Giacomin, T.; Hellermann, M. von; Jakhar, S.; Johnson, D.; Kaschuk, Y.; Kusama, Y.; Lee, H.G.; Levesy, B.

2013-01-01

Highlights: ► An overview of the Port Integration hardware for tenant system hosting inside ITER diagnostics ports is given. ► The main challenges for diagnostic port integration engineering are presented. ► The actions taken for a common modular approach and a coordinated design are detailed. -- Abstract: ITER will have a set of 45 diagnostics to ensure controlled operation. Many of them are integrated in the ITER ports. This paper addresses the integration process of the diagnostic systems and the approach taken to enable coordinated progress. An overview of the Port Integration hardware introduces the various structures needed for hosting tenant systems inside ITER diagnostics ports. The responsibilities of the different parties involved (ITER Organization and the Domestic Agencies) are outlined. The main challenges for diagnostic port integration engineering are summarized. The plan for a common approach to design and manufacture of the supporting structures, in particular the Port Plug is detailed. A coordinated design including common components and a common approach for neutronic analyses is proposed. One particular port, the equatorial port 11, is used to illustrate the approach

Ports, policies and interventions in ports in Portugal - 20th Century

OpenAIRE

Dias, Emílio Brògueira; Alves, Jorge Fernandes

2010-01-01

Ce texte, inspiré des données issues des travaux des deux auteurs, aborde, de manière synthétique, les grandes lignes des transformations portuaires au Portugal, à travers un panorama des différents ports et de leur évolution. Cet exposé se focalise sur les exemples les plus significatifs que sont les ports de Leixões, Aveiro, Lisbonne, Setubal et Sines. This text, based on the data used in previous works by the authors, seeks to assess briefly, the main lines of transformations in Portuga...

Wounds caused by contact with muzzle-lift relief ports (Mag-Na-Port).

Science.gov (United States)

Rogers, D R; Shem, R J

1992-12-01

Fan-shaped stippled burns were produced on the skin when a revolver whose barrel had been modified by the Mag-Na-Port process was fired twice with the side of the muzzle in contact. A grazing wound was produced by one bullet, and an oblique entry was produced by the other. The characteristics of Mag-Na-Port wounds and test shots are described, and these are compared with test shots from two other higher power revolvers.

Port performance evaluation tool based on microsimulation model

Directory of Open Access Journals (Sweden)

Tsavalista Burhani Jzolanda

2017-01-01

Full Text Available As port performance is becoming correlative to national competitiveness, the issue of port performance evaluation has significantly raised. Port performances can simply be indicated by port service levels to the ship (e.g., throughput, waiting for berthing etc., as well as the utilization level of equipment and facilities within a certain period. The performances evaluation then can be used as a tool to develop related policies for improving the port’s performance to be more effective and efficient. However, the evaluation is frequently conducted based on deterministic approach, which hardly captures the nature variations of port parameters. Therefore, this paper presents a stochastic microsimulation model for investigating the impacts of port parameter variations to the port performances. The variations are derived from actual data in order to provide more realistic results. The model is further developed using MATLAB and Simulink based on the queuing theory.

Modelo de simulação da temperatura e umidade relativa do ar no interior de estufa plástica Simulation model of air temperature and relative humidity in to plastic greenhouses

Directory of Open Access Journals (Sweden)

Edilson Costa

2004-04-01

Full Text Available A simulação dos parâmetros climáticos de temperatura e umidade relativa do ar no interior de uma estufa plástica, por meio do balanço de energia, pode propiciar ao produtor uma ferramenta de auxílio na tomada de decisão. Nesse propósito, realizou-se uma simulação das condições no interior de estufa plástica, em função de parâmetros externos e internos a ela. A simulação revelou uma temperatura no interior da estufa plástica de 23,6 ºC, e os sensores revelaram um valor médio de 24,1 ºC para o período de cultivo da alface. Para a umidade relativa no interior da estufa plástica, o valor simulado foi de 61,6%, e o obtido com o auxílio de sensores foi de 66,0%. Os valores simulados apresentaram-se próximos dos valores obtidos pelos sensores, mostrando que o modelo pode ser usado para a estimativa da temperatura e umidade relativa do ar no interior da estufa plástica.Simulation of climatic parameters inside air temperature and relative humidity of plastic greenhouse, trough energy balance, allows to growers a good technical tool on the decision making to improve the performance of inside environments. A simulation of internal conditions based on external and internal parameters was evaluated. The results showed the inside mean temperature of 23.6 ºC in comparison with the experimental value of 24.1 ºC, for the cultivated period. The simulated relative humidity presented a value of 61.6% against 66.0% obtained by the sensors. The simulated values were closed to the values obtained by the sensors, which means that the model can be used to determine the internal conditions of plastic greenhouses.

Analysis of laparoscopic port site complications: A descriptive study

Directory of Open Access Journals (Sweden)

Somu Karthik

2013-01-01

Full Text Available Context: The rate of port site complications following conventional laparoscopic surgery is about 21 per 100,000 cases. It has shown a proportional rise with increase in the size of the port site incision and trocar. Although rare, complications that occur at the port site include infection, bleeding, and port site hernia. Aims: To determine the morbidity associated with ports at the site of their insertion in laparoscopic surgery and to identify risk factors for complications. Settings and Design: Prospective descriptive study. Materials and Methods: In the present descriptive study, a total of 570 patients who underwent laparoscopic surgeries for various ailments between August 2009 and July 2011 at our institute were observed for port site complications prospectively and the complications were reviewed. Statistical Analysis Used: Descriptive statistical analysis was carried out in the present study. The statistical software, namely, SPSS 15.0 was used for the analysis of the data. Results: Of the 570 patients undergoing laparoscopic surgery, 17 (3% had developed complications specifically related to the port site during a minimum follow-up of three months; port site infection (PSI was the most frequent (n = 10, 1.8%, followed by port site bleeding (n = 4, 0.7%, omentum-related complications (n = 2; 0.35%, and port site metastasis (n = 1, 0.175%. Conclusions: Laparoscopic surgeries are associated with minimal port site complications. Complications are related to the increased number of ports. Umbilical port involvement is the commonest. Most complications are manageable with minimal morbidity, and can be further minimized with meticulous surgical technique during entry and exit.

Analysis of laparoscopic port site complications: A descriptive study

Science.gov (United States)

Karthik, Somu; Augustine, Alfred Joseph; Shibumon, Mundunadackal Madhavan; Pai, Manohar Varadaraya

2013-01-01

CONTEXT: The rate of port site complications following conventional laparoscopic surgery is about 21 per 100,000 cases. It has shown a proportional rise with increase in the size of the port site incision and trocar. Although rare, complications that occur at the port site include infection, bleeding, and port site hernia. AIMS: To determine the morbidity associated with ports at the site of their insertion in laparoscopic surgery and to identify risk factors for complications. SETTINGS AND DESIGN: Prospective descriptive study. MATERIALS AND METHODS: In the present descriptive study, a total of 570 patients who underwent laparoscopic surgeries for various ailments between August 2009 and July 2011 at our institute were observed for port site complications prospectively and the complications were reviewed. STATISTICAL ANALYSIS USED: Descriptive statistical analysis was carried out in the present study. The statistical software, namely, SPSS 15.0 was used for the analysis of the data. RESULTS: Of the 570 patients undergoing laparoscopic surgery, 17 (3%) had developed complications specifically related to the port site during a minimum follow-up of three months; port site infection (PSI) was the most frequent (n = 10, 1.8%), followed by port site bleeding (n = 4, 0.7%), omentum-related complications (n = 2; 0.35%), and port site metastasis (n = 1, 0.175%). CONCLUSIONS: Laparoscopic surgeries are associated with minimal port site complications. Complications are related to the increased number of ports. Umbilical port involvement is the commonest. Most complications are manageable with minimal morbidity, and can be further minimized with meticulous surgical technique during entry and exit. PMID:23741110

Interior design for passive solar homes

Science.gov (United States)

Breen, J. C.

1981-07-01

The increasing emphasis on refinement of passive solar systems brought recognition to interior design as an integral part of passive solar architecture. Interior design can be used as a finetuning tool minimizing many of the problems associated with passive solar energy use in residential buildings. In addition, treatment of interior space in solar model homes may be a prime factor in determining sales success. A new style of interior design is evolving in response to changes in building from incorporating passive solar design features. The psychology behind passive solar architecture is reflected in interiors, and selection of interior components increasingly depends on the functional suitably of various interior elements.

Interior design for passive solar homes

Energy Technology Data Exchange (ETDEWEB)

Breen, J. C.

1981-07-01

The increasing emphasis on refinement of passive solar systems has brought recognition to interior design as an integral part of passive solar architecture. Interior design can be used as a finetuning tool minimizing many of the problems associated with passive solar energy use in residential buildings. In addition, treatment of interior space in solar model homes may be a prime factor in determining sales success. A new style of interior design is evolving in response to changes in building form incorporating passive solar design features. The psychology behind passive solar architecture is reflected in interiors, and selection of interior components increasingly depends on the functional suitability of various interior elements.

Vectorization, parallelization and porting of nuclear codes (porting). Progress report fiscal 1998

International Nuclear Information System (INIS)

Nemoto, Toshiyuki; Kawai, Wataru; Ishizuki, Shigeru; Kawasaki, Nobuo; Kume, Etsuo; Adachi, Masaaki; Ogasawara, Shinobu

2000-03-01

Several computer codes in the nuclear field have been vectorized, parallelized and transported on the FUJITSU VPP500 system, the AP3000 system and the Paragon system at Center for Promotion of Computational Science and Engineering in Japan Atomic Energy Research Institute. We dealt with 12 codes in fiscal 1998. These results are reported in 3 parts, i.e., the vectorization and parallelization on vector processors part, the parallelization on scalar processors part and the porting part. In this report, we describe the porting. In this porting part, the porting of Monte Carlo N-Particle Transport code MCNP4B2 and Reactor Safety Analysis code RELAP5 on the AP3000 are described. In the vectorization and parallelization on vector processors part, the vectorization of General Tokamak Circuit Simulation Program code GTCSP, the vectorization and parallelization of Molecular Dynamics Ntv Simulation code MSP2, Eddy Current Analysis code EDDYCAL, Thermal Analysis Code for Test of Passive Cooling System by HENDEL T2 code THANPACST2 and MHD Equilibrium code SELENEJ on the VPP500 are described. In the parallelization on scalar processors part, the parallelization of Monte Carlo N-Particle Transport code MCNP4B2, Plasma Hydrodynamics code using Cubic Interpolated propagation Method PHCIP and Vectorized Monte Carlo code (continuous energy model/multi-group model) MVP/GMVP on the Paragon are described. (author)

Single port laparoscopic ileocaecal resection for Crohn's disease: a multicentre comparison with multi-port laparoscopy

NARCIS (Netherlands)

Carvello, M.; de Groof, E. J.; de Buck van Overstraeten, A.; Sacchi, M.; Wolthuis, A. M.; Buskens, C. J.; D'Hoore, A.; Bemelman, W. A.; Spinelli, A.

2018-01-01

AimSingle port (SP) ileocaecal resection (ICR) is an established technique but there are no large studies comparing SP and multi-port (MP) laparoscopic surgery in Crohn's disease (CD). The aim of this study was to compare postoperative pain scores and analgesia requirements after SP and MP

Sustainable Commercial Interior Design

OpenAIRE

Keane, Órla

2009-01-01

This dissertation looks at the environmental benefits of 3 key areas in relation to interior design: Energy, Water and Air; energy efficient lighting, water efficient plumbing fixtures and the effects of interior materials and finishes on indoor air quality. Qualitative research methodology: Extensive literature review of texts available on these topics, and also of the relevant building codes and environmental legislation applicable to Irish interior designers and the built environment. ...

Port Sunlight, essai architectural et social

OpenAIRE

Machet, Laurence

2017-01-01

The purpose of this article is to examine the city of Port Sunlight, its history, design and originality. Created by William Lever in 1888 in order to house his newly-built soap factory, Port Sunlight is part of the numerous “factory villages” built in the wake of the industrial revolution according to philanthropic and utilitarian principles. But this article intends to show that Port Sunlight differs from other factory towns. Its careful design, elaborate architecture and public facilities ...

Assessing Port Governance, Devolution and Terminal Performance in Nigeria

Directory of Open Access Journals (Sweden)

D. E. Onwuegbuchunam

2018-02-01

Full Text Available Concerns about performance and efficiency in port terminals led many national governments to embark on port reforms. The Federal government of Nigeria, for example, adopted the Landlord port model which brought about concessioning of port terminals to private operators. Despite high investments in terminal facilities by the private terminal operators, there are still complaints about level of service offered to port users. This paper applied key performance indicator metrics and parameters of queuing model in assessing performance of Nigeria’s concessioned port terminals. Data for the study were obtained from terminal level records of cargo and ship handling activities for years 2000 to 2015. Major findings indicate that cargo and vessel throughputs improved after the reforms in the six ports examined. However, much variability was observed in trends in ships’ turnround times across all ports after the concession policy implementation. Additional results from the queuing model analysis suggest that the high ships turnround times observed in some ports are associated to delays in ship operation at the berths. The paper recommends that policy interventions be focused on ship operations at the berths as a step in improving service level in the port terminals.

Extended-Range Passive RFID and Sensor Tags

Science.gov (United States)

Fink, Patrick W.; Kennedy, Timothy F.; Lin, Gregory Y.; Barton, Richard

2012-01-01

Extended-range passive radio-frequency identification (RFID) tags and related sensor tags are undergoing development. A tag of this type incorporates a retroreflective antenna array, so that it reflects significantly more signal power back toward an interrogating radio transceiver than does a comparable passive RFID tag of prior design, which does not incorporate a retroreflective antenna array. Therefore, for a given amount of power radiated by the transmitter in the interrogating transceiver, a tag of this type can be interrogated at a distance greater than that of the comparable passive RFID or sensor tag of prior design. The retroreflective antenna array is, more specifically, a Van Atta array, named after its inventor and first published in a patent issued in 1959. In its simplest form, a Van Atta array comprises two antenna elements connected by a transmission line so that the signal received by each antenna element is reradiated by the other antenna element (see Figure 1). The phase relationships among the received and reradiated signals are such as to produce constructive interference of the reradiated signals; that is, to concentrate the reradiated signal power in a direction back toward the source. Hence, an RFID tag equipped with a Van Atta antenna array automatically tracks the interrogating transceiver. The effective gain of a Van Atta array is the same as that of a traditional phased antenna array having the same number of antenna elements. Additional pairs of antenna elements connected by equal-length transmission lines can be incorporated into a Van Atta array to increase its directionality. Like some RFID tags here-to-fore commercially available, an RFID or sensor tag of the present developmental type includes one-port surface-acoustic-wave (SAW) devices. In simplified terms, the mode of operation of a basic one-port SAW device as used heretofore in an RFID device is the following: An interrogating radio signal is converted, at an input end, from

Port-Orford-Cedar Root Disease

Science.gov (United States)

Lewis F. Roth; Robert D. Jr. Harvey; John T. Kliejunas

1987-01-01

The most serious disease of Port-Orford-cedar (Chamaecyparis lawsoniana (A. Murr.) Parl.) is a root disease caused by the fungus Phytophthora lateralis. Nursery stock, ornamentals, and timber trees are subject to attack. Other species of Chamaecyparis are less susceptible than Port-Orford-cedar, and trees of other genera are not affected.

Port pricing : principles, structure and models

OpenAIRE

Meersman, Hilde; Strandenes, Siri Pettersen; Van de Voorde, Eddy

2014-01-01

Price level and price transparency are input to shippers’ choice of supply chain and transport mode. In this paper, we analyse current port pricing structures in the light of the pricing literature and consider opportunities for improvement. We present a detailed overview of pricing criteria, who sets prices and who ultimately foots the bill for port-of-call charges, cargo-handling fees and congestion charges. Current port pricing practice is based on a rather linear structure and fails to in...

Ports Primer: 7.1 Environmental Impacts

Science.gov (United States)

Port operations can lead to environmental impacts on air, water and land. Many communities with environmental justice concerns also experience disparities in health outcomes that they attribute to exposure to emissions from port operations.

Ports Primer: 7.0 Environmental Impacts

Science.gov (United States)

Port operations can lead to environmental impacts on air, water and land. Many communities with environmental justice concerns also experience disparities in health outcomes that they attribute to exposure to emissions from port operations.

Integrating sustainability in interior design studio

OpenAIRE

Karslı, Umut Tuğlu

2013-01-01

Teaching methods on concept of sustainability are frequently searched in the interior architecture education. The purpose of this study is to propose a model for integrating sustainability in interior design studio. In this context, the first part of the research defines relationship between sustainability and interior architecture and determines sustainable interior design principles. In the second part, an interior design studio model is proposed and principles determined in the first part ...

Ports Primer: 3.3 Federal and International Governance

Science.gov (United States)

State and local governments are important players in port governance and in oversight of transportation projects that may affect ports. Private corporations may also play a role if they lease or own a terminal at a port.

Radiologically-placed venous ports in children under venous anesthesia

International Nuclear Information System (INIS)

Jang, Joo Yeon; Jeon, Ung Bae; Choo, Ki Seok; Hwang, Jae Yeon; Kim, Yong Woo; Lee, Yun Jin; Nam, Sang Ool; Lim, Young Tak

2015-01-01

To evaluate the efficacy and safety of radiologic venous port placement in children under venous anesthesia. Between April 2009 and July 2011, 44 ports were implanted in 41 children (24 boys, 17 girls). The age of patients ranged from 9 months to 19 years (mean, 6.5 years) and their body weights ranged from 6.8 kg to 56.3 kg (mean, 23.2 kg). Right internal jugular vein access was used in 42 ports, right subclavian vein in 1, and left subclavian in 1. Durability and complications of port implantation were reviewed. The technical success rate was 100%. The catheter life was 10-661 days (mean 246 days). Two patients died during the follow-up period, 21 and 6 ports were removed at the end of treatment or as a result of complications, respectively. One port was removed and replaced by a Hickmann catheter. Three ports were explanted due to port-related sepsis, one due to a catheter kink, and two for unexplained fever or insertion site pain. The overall port-related infection was 3 cases (6.8%, 0.28/1000 catheter days). Venous port placement by interventional radiologists in children under intravenous sedation is relatively safe, with a high rate of technical success and low rate of complications.

Radiologically-placed venous ports in children under venous anesthesia

Energy Technology Data Exchange (ETDEWEB)

Jang, Joo Yeon; Jeon, Ung Bae; Choo, Ki Seok; Hwang, Jae Yeon; Kim, Yong Woo; Lee, Yun Jin; Nam, Sang Ool; Lim, Young Tak [Pusan National University School of Medicine, Yangsan (Korea, Republic of)

2015-02-15

To evaluate the efficacy and safety of radiologic venous port placement in children under venous anesthesia. Between April 2009 and July 2011, 44 ports were implanted in 41 children (24 boys, 17 girls). The age of patients ranged from 9 months to 19 years (mean, 6.5 years) and their body weights ranged from 6.8 kg to 56.3 kg (mean, 23.2 kg). Right internal jugular vein access was used in 42 ports, right subclavian vein in 1, and left subclavian in 1. Durability and complications of port implantation were reviewed. The technical success rate was 100%. The catheter life was 10-661 days (mean 246 days). Two patients died during the follow-up period, 21 and 6 ports were removed at the end of treatment or as a result of complications, respectively. One port was removed and replaced by a Hickmann catheter. Three ports were explanted due to port-related sepsis, one due to a catheter kink, and two for unexplained fever or insertion site pain. The overall port-related infection was 3 cases (6.8%, 0.28/1000 catheter days). Venous port placement by interventional radiologists in children under intravenous sedation is relatively safe, with a high rate of technical success and low rate of complications.

Overtopping hazards to port activities: Application of a new methodology to risk management (POrt Risk MAnagement Tool)

International Nuclear Information System (INIS)

Alises, Ana; Molina, Rafael; Gómez, Rebeca; Pery, Pascual; Castillo, Carmen

2014-01-01

In the past 20 years, the need of ports to serve a fleet whose dimensions are continuously increasing due to economies of scale, has derived on a port infrastructures growth with a trend to look for greater drafts at deeper waters and therefore the protection structures built in the last years have been increasingly exposed to severer maritime climate action. Consequently, overtopping phenomenon has been identified as a potential risk factor able to cause structural damages and operative failure modes to vulnerable economic activities located at these port facilities. Port activities must be developed ensuring operative and safety conditions what imply reducing uncertainties of overtopping phenomena by using prediction methods which may allow overtopping risk management. This paper provides a risk assessment methodology which is integrated into an overtopping risk management framework to cope with safety problems in port exploitation. Overtopping risk value is measured by combining probability of occurrence of an undesirable event together with its consequences, estimated in terms of costs or delays and given in base of the vulnerability of the affected port system. The development of this methodology is described and finally applied to a real case study what seems to reinforce the validity of the proposed method to overtopping risk assessment. - Highlights: • Infrastructure risk assessment involves both probabilistic and economic techniques. • Risk equation is posed by the combination of probability, vulnerability and cost. • Port infrastructures' vulnerability level depends on climate agents' action. • Economic value of natural hazards consequences is linked with vulnerability level. • Project planning process should be done taking into account the project's risk distribution

Slewing Port Jib Cranes

OpenAIRE

Boris Visočnik; Stojan Kravanja

2002-01-01

The paper presents slewing port cranes with a luffing jib. The advantages of slewing port jib cranes are high lifting capacities, high speeds of re-loading and excellent mobility since they are capable of load lifting, travelling, luffing and slewing. The paper gives a detailed description of their characteristics such as the highest reached load-carrying capacities, speeds of motion and accelerations. It also presents the crane assembly, driving mechanisms, loads and load cases, transport by...

Securing a port's future through Circular Economy: Experiences from the Port of Gävle in contributing to sustainability.

Science.gov (United States)

Carpenter, Angela; Lozano, Rodrigo; Sammalisto, Kaisu; Astner, Linda

2018-03-01

Ports are an important player in the world, due to their role in global production and distributions systems. They are major intermodal transport hubs, linking the sea to the land. For all ports, a key requirement for commercial and economic viability is to retain ships using them and to remain accessible to those ships. Ports need to find approaches to help them remain open. They must ensure their continued economic viability. At the same time, they face increasing pressure to become more environmentally and socially conscious. This paper examines the approach taken by the Port of Gävle, Sweden, which used contaminated dredged materials to create new land using principles of Circular Economy. The paper demonstrates that using Circular Economy principles can be a viable way of securing a port's future and contributing to its sustainability, and that of the city/region where it operates. Copyright © 2018 Elsevier Ltd. All rights reserved.

Queuing theory models used for port equipment sizing

Science.gov (United States)

Dragu, V.; Dinu, O.; Ruscă, A.; Burciu, Ş.; Roman, E. A.

2017-08-01

The significant growth of volumes and distances on road transportation led to the necessity of finding solutions to increase water transportation market share together with the handling and transfer technologies within its terminals. It is widely known that the biggest times are consumed within the transport terminals (loading/unloading/transfer) and so the necessity of constantly developing handling techniques and technologies in concordance with the goods flows size so that the total waiting time of ships within ports is reduced. Port development should be achieved by harmonizing the contradictory interests of port administration and users. Port administrators aim profit increase opposite to users that want savings by increasing consumers’ surplus. The difficulty consists in the fact that the transport demand - supply equilibrium must be realised at costs and goods quantities transiting the port in order to satisfy the interests of both parties involved. This paper presents a port equipment sizing model by using queueing theory so that the sum of costs for ships waiting operations and equipment usage would be minimum. Ship operation within the port is assimilated to a mass service waiting system in which parameters are later used to determine the main costs for ships and port equipment.

Adding some context to port marketing: Exploring the content and measurement of market orientation in the port industry

OpenAIRE

Kounoupas, Evangelos; Pardali, Angeliki

2015-01-01

Understanding and responding to customer needs is the essence of the marketing concept and as such it has been discussed in various fields of business and economic literature. Port economics and management literature has thoroughly investigated areas such as port efficiency and effectiveness, understanding and overcoming competitive pressures and identifying the sources of potential sustainable competitive advantage. In line with this discussion, albeit with a significant time delay, port eco...

Catheter fracture of intravenous ports and its management.

Science.gov (United States)

Wu, Ching-Yang; Fu, Jui-Ying; Feng, Po-Hao; Kao, Tsung-Chi; Yu, Sheng-Yueh; Li, Hao-Jui; Ko, Po-Jen; Hsieh, Hung-Chang

2011-11-01

Intravenous ports are widely used for oncology patients. However, catheter fractures may lead to the need for re-intervention. We aimed to identify the risk factors associated with catheter fractures. Between January 1 and December 31, 2006, we retrospectively reviewed the clinical data and plain chest films of 1,505 patients implanted with an intravenous port at Chang Gung Memorial Hospital. Different vascular sites were compared using the chi-square or Fisher's exact test for categorical variables, and the t test was used for continuous variables with normal distribution; P port type Arrow French (Fr.) 8.1 (P port and catheter removal is recommended. Female gender, intravenous port implantation via the subclavian route, and the Arrow Fr. 8.1 port were found to be risk factors. Patients with these risk factors should be monitored closely to avoid catheter fractures.

Study on the key technologies of the Transfer Equipment Cask for Tokamak Equator Port Plug

Energy Technology Data Exchange (ETDEWEB)

Wang, Buyun, E-mail: ayun@iim.ac.cn [Department of Automation, University of Science and Technology of China, Hefei, Anhui 230027 (China); Robot Sensors and Human-Machine Interaction Laboratory, Institute of Intelligent Machines, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Gao, Lifu [Department of Automation, University of Science and Technology of China, Hefei, Anhui 230027 (China); Robot Sensors and Human-Machine Interaction Laboratory, Institute of Intelligent Machines, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Cao, Huibin; Sun, Jian [Robot Sensors and Human-Machine Interaction Laboratory, Institute of Intelligent Machines, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Sun, Yuxiang; Song, Quanjun; Ma, Chengxue; Chang, Li; Shuang, Feng [Department of Automation, University of Science and Technology of China, Hefei, Anhui 230027 (China); Robot Sensors and Human-Machine Interaction Laboratory, Institute of Intelligent Machines, Chinese Academy of Sciences, Hefei, Anhui 230031 (China)

2014-12-15

Highlights: • Design on Intelligent Air Transfer System (IATS) for Transfer Equipment Cask (TECA). • A rhombic-like parallel robot for docking with minimum misalignment. • Design on electro-hydraulic servo system of the TECA for Tokamak Equator Port Plug (TEPP) manipulation. • A control architecture with several algorithms and information acquired from sensors could be used by the TECA for Remote Handling (RH). - Abstract: The Transfer Equipment Cask (TECA) is a key solution for Remote Handling (RH) in Tokamak Equator Port Plug (TEPP) operations. From the perspectives of both engineering and technical designs of effective experiments on the TEPP, key technologies on these topics covering the TECA are required. According to conditions in ITER (International Thermonuclear Experimental Reactor) and features of the TEPP, this paper introduces the design of an Intelligent Air Transfer System (IATS) with an adaptive attitude and high precision positioning that transports a cask system of more than 30 tons from the Tokamak Building (TB) to the Hot Cell Building (HCB). Additionally, different actuators are discussed, and the hydraulic power drive is eventually selected and designed. A rhombic-like parallel robot is capable of being used for docking with minimum misalignment. Practical mechanisms of the cask system are presented for hostile environments. A control architecture with several algorithms and information acquired from sensors could be used by the TECA. These designs yield realistic and extended applications for the RH of ITER.

Feasibility of Reduced Port Laparoscopic Colectomy for Colon Cancer.

Science.gov (United States)

Tsutsumi, Soichi; Morita, Hiroki; Fujii, Takaaki; Suto, Toshinaga; Yajima, Reina; Takada, Takahiro; Asao, Takayuki; Kuwano, Hiroyuki

2015-06-01

Reduced port laparoscopic surgery has recently emerged as a method to improve the cosmetic results of conventional laparoscopic surgery. We reported our technique of reduced port laparoscopic colectomy using 3-port and short-time outcomes. Between 2005 and 2012, we performed 161 reduced port laparoscopic colectomies using the 3-port technique. Data analyzed in-cluded age, gender, body mass index (BMI), duration of surgery, number of harvested lymph nodes, and duration of hospital stay. All of the cases were successfully performed using the 3-port procedure. The median durations of surgery and postoperative hospital stay were 140 mm (range 75-463 mm) and 9 days (range 5-38 days), respectively. No mortality was associated with this technique. Reduced port laparoscopic colectomy is feasible and may have advantages over conventional laparoscopic colectomy.

Classification and prediction of port variables

Energy Technology Data Exchange (ETDEWEB)

Molina Serrano, B.

2016-07-01

Many variables are included in planning and management of port terminals. They can beeconomic, social, environmental and institutional. Agent needs to know relationshipbetween these variables to modify planning conditions. Use of Bayesian Networks allowsfor classifying, predicting and diagnosing these variables. Bayesian Networks allow forestimating subsequent probability of unknown variables, basing on know variables.In planning level, it means that it is not necessary to know all variables because theirrelationships are known. Agent can know interesting information about how port variablesare connected. It can be interpreted as cause-effect relationship. Bayesian Networks can beused to make optimal decisions by introduction of possible actions and utility of theirresults.In proposed methodology, a data base has been generated with more than 40 port variables.They have been classified in economic, social, environmental and institutional variables, inthe same way that smart port studies in Spanish Port System make. From this data base, anetwork has been generated using a non-cyclic conducted grafo which allows for knowingport variable relationships - parents-children relationships-. Obtained network exhibits thateconomic variables are – in cause-effect terms- cause of rest of variable typologies.Economic variables represent parent role in the most of cases. Moreover, whenenvironmental variables are known, obtained network allows for estimating subsequentprobability of social variables.It has been concluded that Bayesian Networks allow for modeling uncertainty in aprobabilistic way, even when number of variables is high as occurs in planning andmanagement of port terminals. (Author)

Occupational hazards to health of port workers.

Science.gov (United States)

Wang, Yukun; Zhan, Shuifen; Liu, Yan; Li, Yan

2017-12-01

The aim of this article is to reduce the risk of occupational hazards and improve safety conditions by enhancing hazard knowledge and identification as well as improving safety behavior for freight port enterprises. In the article, occupational hazards to health and their prevention measures of freight port enterprises have been summarized through a lot of occupational health evaluation work, experience and understanding. Workers of freight port enterprises confront an equally wide variety of chemical, physical and psychological hazards in production technology, production environment and the course of labor. Such health hazards have been identified, the risks evaluated, the dangers to health notified and effective prevention measures which should be put in place to ensure the health of the port workers summarized. There is still a long way to go for the freight port enterprises to prevent and control the occupational hazards. Except for occupational hazards and their prevention measures, other factors that influence the health of port workers should also be paid attention to, such as age, work history, gender, contraindication and even the occurrence and development rules of occupational hazards in current production conditions.

INSTITUTIONAL AND MANAGEMENT STRUCTURE OF RUSSIAN ARCTIC SEA PORTS

Directory of Open Access Journals (Sweden)

P. A. Bryzgalov

2012-01-01

Full Text Available Institutional and management structure of any sea port is a system of interaction between commercial enterprises engaged in cargo operations in port, a subsidiary of Rosmorport FSUE, Sea Port Authority and a number of services (immigration, customs and sanitary-veterinary. Institutional and management structure of some Russian Arctic sea ports is significantly different from the typical one resulting in management problems for these socially significant objects of the Russian Arctic. A plan is proposed to improve the organizational and administrative structure of these ports based on the use of domestic and international experience in port infrastructure management including effective cooperation between the state and the private business.

Peripheral Venous Access Ports: Outcomes Analysis in 109 Patients

International Nuclear Information System (INIS)

Bodner, Leonard J.; Nosher, John L.; Patel, Kaushik M.; Siegel, Randall L.; Biswal, Rajiv; Gribbin, Christopher E.; Tokarz, Robert

2000-01-01

Purpose: To perform a retrospective outcomes analysis of central venous catheters with peripheral venous access ports, with comparison to published data.Methods: One hundred and twelve central venous catheters with peripherally placed access ports were placed under sonographic guidance in 109 patients over a 4-year period. Ports were placed for the administration of chemotherapy, hyperalimentation, long-term antibiotic therapy, gamma-globulin therapy, and frequent blood sampling. A vein in the upper arm was accessed in each case and the catheter was passed to the superior vena cava or right atrium. Povidone iodine skin preparation was used in the first 65 port insertions. A combination of Iodophor solution and povidone iodine solution was used in the last 47 port insertions. Forty patients received low-dose (1 mg) warfarin sodium beginning the day after port insertion. Three patients received higher doses of warfarin sodium for preexistent venous thrombosis. Catheter performance and complications were assessed and compared with published data.Results: Access into the basilic or brachial veins was obtained in all cases. Ports remained functional for a total of 28,936 patient days. The port functioned in 50% of patients until completion of therapy, or the patient's expiration. Ports were removed prior to completion of therapy in 18% of patients. Eleven patients (9.9% of ports placed) suffered an infectious complication (0.38 per thousand catheter-days)-in nine, at the port implantation site, in two along the catheter. In all 11 instances the port was removed. Port pocket infection in the early postoperative period occurred in three patients (4.7%) receiving a Betadine prep vs two patients (4.2%) receiving a standard O.R. prep. This difference was not statistically significant (p = 0.9). Venous thrombosis occurred in three patients (6.8%) receiving warfarin sodium and in two patients (3%) not receiving warfarin sodium. This difference was not statistically significant

Soil contamination issues at U.S. ports

International Nuclear Information System (INIS)

Rice, D.W.; Hagner, D.

1991-01-01

This paper reports that seven large and medium size west coast ports were surveyed during August 1990 to determine their involvement with hydrocarbon contaminated soils and activities associated with the characterization and remediation of these soils. All ports surveyed indicated that hey have hydrocarbon contaminated soil problems. Although other west coast ports do not have the scale of petroleum transfer and storage facilities that the Prot of Los Angeles has, all ports had tenants with bulk oil or fuel storage in aboveground tanks and were undertaking characterization and remediation work. Hydrocarbon contaminated soil problems were associated with these facilities or with decommissioned facilities of this type

Analyzing Growth Opportunity of Port from the Resource-based Perspective The Case of Port of Tanjung Pelepas Malaysia

OpenAIRE

Subhan, Muhammad; Abdul Ghani, Ahmad Bashawir

2008-01-01

Capturing growth opportunity has become a major integral activity of any port to sustain growth and competitive advantage. One of the famous strategies in leveraging sustainable growth and competitive advantage is the resource-based theory application into port strategic management, viewing resources of the port (internal and external) and its capabilities as the sources for achieving competitive advantage. In this study, we attempt to identify, exploit, and analyze growth opportunity of a Ma...

Step-wise integration of single-port laparoscopic surgery into routine colorectal surgical practice by use of a surgical glove port.

Science.gov (United States)

Hompes, R; Lindsey, I; Jones, O M; Guy, R; Cunningham, C; Mortensen, N J; Cahill, R A

2011-06-01

The cost associated with single-port laparoscopic access devices may limit utilisation of single-port laparoscopic surgery by colorectal surgeons. This paper describes a simple and cheap access modality that has facilitated the widespread adoption of single-port technology in our practice both as a stand-alone procedure and as a useful adjunct to traditional multiport techniques. A surgical glove port is constructed by applying a standard glove onto the rim of the wound protector/retractor used during laparoscopic resectional colorectal surgery. To illustrate its usefulness, we present our total experience to date and highlight a selection of patients presenting for a range of elective colorectal surgery procedures. The surgical glove port allowed successful completion of 25 single-port laparoscopic procedures (including laparoscopic adhesiolysis, ileo-rectal anastomosis, right hemicolectomy, total colectomy and low anterior resection) and has been used as an adjunct in over 80 additional multiport procedures (including refashioning of a colorectal anastomosis made after specimen extraction during a standard multiport laparoscopic anterior resection). This simple, efficient device can allow use of single-port laparoscopy in a broader spectrum of patients either in isolation or in combination with multiport surgery than may be otherwise possible for economic reasons. By separating issues of cost from utility, the usefulness of the technical advance inherent within single-port laparoscopy for colorectal surgery can be better appreciated. We endorse the creative innovation inherent in this approach as surgical practice continues to evolve for ever greater patient benefit.

78 FR 24069 - Safety Zone; 12th Annual Saltwater Classic; Port Canaveral Harbor; Port Canaveral, FL

Science.gov (United States)

2013-04-24

... under Executive Order 13045, Protection of Children from Environmental Health Risks and Safety Risks. This rule is not an economically significant rule and does not create an environmental risk to health...-AA00 Safety Zone; 12th Annual Saltwater Classic; Port Canaveral Harbor; Port Canaveral, FL AGENCY...

Interior Design Factors in Library Facilities.

Science.gov (United States)

Jackson, Patricia Ann

When planning the interior of a library facility, the planning team of librarian, library consultant, architect, and interior design consultant must focus attention on the basic principles of interior design and the psychological needs of the user. Colors for an interior should be selected with careful regard to space, light, and emotional and…

Research for Foreign Advanced Ports for Protection and Development Experience

Science.gov (United States)

Zhang, Lu; Tian, Mingjing; Zhao, Junjie; Shou, Youping; Wang, Ning; Qiao, Jianzhe; Li, Guanglou

2018-04-01

Into the twenty-first century, the process globalization of economic and trade is getting faster and faster, As of 2014, China's annual port trading amount topped the world, But in the port of environmental protection sustainable development approach with foreign advanced port environmental management concept has a big gap. Combined with the present situation of modern ports in China. Drawing lessons from foreign advanced environmental protection idea of port, in order to promote the protection of port environment in our country. The experience of protection and development of foreign advanced port environment will be discussed and discussed.

The Implications of the Growth of Port Throughput on the Port Capacity: the Case of Malaysian Major Container Seaports

Directory of Open Access Journals (Sweden)

J. Jeevan

2015-12-01

Full Text Available Malaysia, situated between East and West, is an interface in world maritime trade, playing a crucial role in the business of moving container boxes in South-eastern parts of Asia. The prominent container terminals in Malaysia such as Port Klang and Port of Tanjung Pelepas are positioned among the top twenty ports in terms of volume handled. The annual average growth of throughputs in Malaysian container ports increased more than three-fold from the year 2000 to 2010. Within this context, the development of Malaysian seaports has been significantly influenced by three forces: increased use of containerisation, significant growth in domestic economic activities and ever-changing patterns in both supply and demand chains, all of which have led to increased transshipment activities and altered shipping routes. This phenomenon has brought dynamic change to Malaysian container ports, resulting in the establishment of new terminals and adapting emerging technology to enhance the ports' ability to accommodate larger vessels and an increased number of containers. This paper aims to present the development of Malaysian container seaports by addressing changes to acreage size and handling volumes during the last three decades. The results of the analysis suggest that major Malaysian ports are experiencing an exponential growth in container trade with the expansion of port capacity following trade growth and need effective strategies to reduce the operational pressures of Malaysian seaports. The results of this research offer directions for development strategies of seaports by utilising the existing inland freight facilities as an effective strategy for capacity enhancement and develop efficient distribution network to meet future demands.

Vectorization, parallelization and porting of nuclear codes on the VPP500 system (porting). Progress report fiscal 1996

Energy Technology Data Exchange (ETDEWEB)

Nemoto, Toshiyuki [Fujitsu Ltd., Tokyo (Japan); Kawasaki, Nobuo; Tanabe, Hidenobu [and others

1998-01-01

Several computer codes in the nuclear field have been vectorized, parallelized and transported on the FUJITSU VPP500 system at Center for Promotion of Computational Science and Engineering in Japan Atomic Energy Research Institute. These results are reported in 3 parts, i.e., the vectorization part, the parallelization part and the porting part. In this report, we describe the porting. In this porting part, the porting of reactor safety analysis code RELAP5/MOD3.2 and RELAP5/MOD3.2.1.2, nuclear data processing system NJOY and 2-D multigroup discrete ordinate transport code TWOTRAN-II are described. And also, a survey for the porting of command-driven interactive data analysis plotting program IPLOT are described. In the parallelization part, the parallelization of 2-Dimensional relativistic electromagnetic particle code EM2D, Cylindrical Direct Numerical Simulation code CYLDNS and molecular dynamics code for simulating radiation damages in diamond crystals DGR are described. And then, in the vectorization part, the vectorization of two and three dimensional discrete ordinates simulation code DORT-TORT, gas dynamics analysis code FLOWGR and relativistic Boltzmann-Uehling-Uhlenbeck simulation code RBUU are described. (author)

INTERIORITY

DEFF Research Database (Denmark)

Hvejsel, Marie Frier

Dealing with the general theme of domestic architectural quality, the PhD thesis ‘INTERIORITY’ takes its point of departure in the continuous and increasing need to improve our capability as architects to theoretically articulate the intangible concept of quality, and to reveal it through an active...... been motivated by the particular hypothesis that an introduction of the notion of interiority, as an ability of the spatial envelope itself to address the sensuous scale of furniture, unfolds a particular dual critical potential signifying our experience of domestic architectural quality: On the one......, tectonically. Hence, it has been a particular idea of the study to explore the relation between furniture, the spatial envelope itself, and its construct by using furniture as an architectural concept. Consequently, the thesis has specifically investigated whether this notion of interiority, describing...

Interior design and healing architecture

DEFF Research Database (Denmark)

Mogensen, Jeppe; Poulsen, Søren Bolvig; Hansen, Allan Grutt

2015-01-01

. Through a mixed-method study, 43 patients from the outpatient-lung department at Hospital Vendsyssel, Denmark were presented with different types of furniture and materials and were asked about their preferences. Additional questions on their experience of the hospital interior were asked to guide......Hospital design is today influenced by the design concept healing architecture, stating that the patients’ healing process is promoted through accommodating physical surroundings. However, despite the increasing amount of research in the field of healing architecture, research on interior design...... and materials are rather limited. To compliment research in hospital interior design with particular focus on the use of interior textiles, this pilot study explores if the patients’ preferences for more home-like hospital interiors can be linked to a preference for textile-based furniture and materials...

A modified method using a two-port approach for accessing the hilar vasculature without transferring an endostapler from camera port to utility port during thoracoscopic right upper lobectomy.

Science.gov (United States)

Jiao, W; Zhao, Y; Xuan, Y; Wang, M

2015-02-01

For thoracoscopic upper lobectomies, most cutting endostaplers must be inserted through the camera port when using a two-port approach. Access to the hilar vasculature through only the utility port remains a challenge. In this study, we describe a procedure to access the hilar vasculature without transferring the endostapler site during a thoracoscopic right upper lobectomy. A 2.5-cm utility anterior incision was made in the fourth intercostal space. The posterior mediastinal visceral pleura were dissected to expose the posterior portion of the right upper bronchus and the anterior trunk of the right pulmonary artery. The pleura over the right hilar vasculature were then peeled with an electrocoagulation hook. The anterior trunk of the right pulmonary artery was then transected with a cutting endostapler through the utility port firstly. This crucial maneuver allowed the endostapler access to the right upper lobe pulmonary vein. The hilar structures were then easily handled in turn. This novel technique was performed successfully in 32 patients, with no perioperative deaths. The average operation time was 120.6 min (range 75-180 min). This novel technique permits effective control of the hilar vessels through the utility port, enabling simple, safe, quick and effective resection.

A microcontroller-based interface circuit for lossy capacitive sensors

International Nuclear Information System (INIS)

Reverter, Ferran; Casas, Òscar

2010-01-01

This paper introduces and analyses a low-cost microcontroller-based interface circuit for lossy capacitive sensors, i.e. sensors whose parasitic conductance (G x ) is not negligible. Such a circuit relies on a previous circuit also proposed by the authors, in which the sensor is directly connected to a microcontroller without using either a signal conditioner or an analogue-to-digital converter in the signal path. The novel circuit uses the same hardware, but it performs an additional measurement and executes a new calibration technique. As a result, the sensitivity of the circuit to G x decreases significantly (a factor higher than ten), but not completely due to the input capacitances of the port pins of the microcontroller. Experimental results show a relative error in the capacitance measurement below 1% for G x x ) shows the effectiveness of the circuit

Trace explosives sensor testbed (TESTbed)

Science.gov (United States)

Collins, Greg E.; Malito, Michael P.; Tamanaha, Cy R.; Hammond, Mark H.; Giordano, Braden C.; Lubrano, Adam L.; Field, Christopher R.; Rogers, Duane A.; Jeffries, Russell A.; Colton, Richard J.; Rose-Pehrsson, Susan L.

2017-03-01

A novel vapor delivery testbed, referred to as the Trace Explosives Sensor Testbed, or TESTbed, is demonstrated that is amenable to both high- and low-volatility explosives vapors including nitromethane, nitroglycerine, ethylene glycol dinitrate, triacetone triperoxide, 2,4,6-trinitrotoluene, pentaerythritol tetranitrate, and hexahydro-1,3,5-trinitro-1,3,5-triazine. The TESTbed incorporates a six-port dual-line manifold system allowing for rapid actuation between a dedicated clean air source and a trace explosives vapor source. Explosives and explosives-related vapors can be sourced through a number of means including gas cylinders, permeation tube ovens, dynamic headspace chambers, and a Pneumatically Modulated Liquid Delivery System coupled to a perfluoroalkoxy total-consumption microflow nebulizer. Key features of the TESTbed include continuous and pulseless control of trace vapor concentrations with wide dynamic range of concentration generation, six sampling ports with reproducible vapor profile outputs, limited low-volatility explosives adsorption to the manifold surface, temperature and humidity control of the vapor stream, and a graphical user interface for system operation and testing protocol implementation.

Development of a self-navigating mobile interior robot application as a security guard/sentry

International Nuclear Information System (INIS)

Klarer, P.R.; Harrington, J.J.

1986-07-01

This paper describes a mobile robot system designed to function as part of an overall security system at a high security facility. The features of this robot system include specialized software and sensors for navigation without the need for external locator beacons or signposts, sensors for remote imaging and intruder detection, and the ability to communicate information either directly to the electronic portion of the security system or to a manned central control center. Other desirable features of the robot system include low weight, compact size, and low power consumption. The robot system can be operated either by remote manual control, or it can operate autonomously where direct human control can be limited to the global command level. The robot can act as a mobile remote sensing platform for alarm assessment or roving patrol, as a point sensor (sentry) in routine security applications, or as an exploratory device in situations potentially hazardous to humans. This robot system may also be used to ''walk-test'' intrusion detection sensors as part of a routine test and maintenance program for an interior intrusion detection system. The hardware, software, and operation of this robot system will be briefly described herein

Assessing the port to port risk of vessel movements vectoring non-indigenous marine species within and across domestic Australian borders.

Science.gov (United States)

Campbell, Marnie L; Hewitt, Chad L

2011-07-01

Biofouling of vessels is implicated as a high risk transfer mechanism of non-indigenous marine species (NIMS). Biofouling on international vessels is managed through stringent border control policies, however, domestic biofouling transfers are managed under different policies and legislative arrangements as they cross internal borders. As comprehensive guidelines are developed and increased compliance of international vessels with 'clean hull' expectations increase, vessel movements from port to port will become the focus of biosecurity management. A semi-quantitative port to port biofouling risk assessment is presented that evaluates the presence of known NIMS in the source port and determines the likelihood of transfer based on the NIMS association with biofouling and environmental match between source and receiving ports. This risk assessment method was used to assess the risk profile of a single dredge vessel during three anticipated voyages within Australia, resulting in negligible to low risk outcomes. This finding is contrasted with expectations in the literature, specifically those that suggest slow moving vessels pose a high to extreme risk of transferring NIMS species.

Robotic right middle lobectomy with a subxiphoid utility port.

Science.gov (United States)

Jayakumar, Shruti; Nardini, Marco; Papoulidis, Pavlos; Dunning, Joel

2018-06-01

We present the case of a 74-year-old man with Stage IIa pulmonary adenocarcinoma, for which he underwent a robotic right middle lobectomy. A 4-armed, 5-port approach was used. Four intercostal ports were created above the ninth rib using the Cerfolio's technique. The subxiphoid port was created in the midline, 5 cm down from the xiphisternum. The robot offers higher image quality, depth perception and improved articulation of the instruments, allowing for more accurate dissection and stitching. The usage of a subxiphoid utility port reduces the clashing between instruments, offers a good angle for stapling and provides a direct view of the instruments entering into the chest. Specimen removal through the subxiphoid port may reduce postoperative pain and enhance patient recovery. The use of the subxiphoid approach as a utility port for robotic surgery is promising and may be a suitable replacement for the traditional utility port.

HomePort

DEFF Research Database (Denmark)

Madsen, Per Printz

2009-01-01

In the last couple of year's computer based home control systems are getting more and more common in modern homes. For instance these systems take care of light control, heat control and security systems.  The latest trend is to use wireless communication like Z-Wave and ZigBee to interconnect...... different components in these systems. One of the characteristics is that each system, like for instance heat and light, has their own specific way of using the communication system.   This paper describes a way to connect different home control systems through an intelligent gateway, called a Home......Port. The HomePort consists of a number of Subsystem communication drivers, a virtual communication layer, an interpreter and a PC- based compiler for a high level control language, called GIL (Gateway intelligence language). The focus in this paper will be on the upper two layers in the Home...

The VisPort Project: Visualization of Port Logistics

Science.gov (United States)

Katsioloudis, Petros J.; Watson, Ginger

2011-01-01

There is concern about the diminishing availability of skilled personnel that can operate in the wide variety of disciplines associated with port operations. Increasing cargo volume, combined with a shrinking workforce, could potentially create alarming situations in the future, hence the motivation to publicize to current students the breadth and…

Enabling information sharing in a port

DEFF Research Database (Denmark)

Olesen, Peter Bjerg; Hvolby, Hans-Henrik; Dukovska-Popovska, Iskra

2012-01-01

Ports are integral parts of many supply chains and are as such a contributing factor to the overall efficiency of the supply chain. Ports are also dynamic entities where things changes continuously. The dynamic nature of ports is also a problem when trying to optimise the utilisation of resources...... and ensure a low lead-time. Information sharing is a very important tool to reduce the effect of dynamism. This paper attempts to explain how information sharing is enabled in such an environment, and which considerations are relevant, both in regards to the information and required technology. The paper...

Port Environmental Management Challenges, Possibilities and Innovations in a Globalization Context

Directory of Open Access Journals (Sweden)

Dione Iara Silveira Kitzmann

2014-12-01

Full Text Available Port activity within an overall port environmental system encompassing the whole coastal area in which ports are situated constitutes an important analytical tool. The considerable potential for controlling and influencing activities that occur in the same geographical area means that ports generate significant positive and negative environmental impacts. This importance and the significant expansion of the Brazilian port sector in recent years gave rise to the need for Port Environmental Management (GAP based on internationally accepted environmental standards. This article discusses nested elements in the concept of port environmental management which take into account new realities of Brazilian ports as well as international standards concerning environmentally appropriate measures for the sector. New international technical proposals are discussed with regard to Brazilian port policy and the port of Rio Grande (Rio Grande do Sul State is used as a case study, highlighting its structures and the model of port environmental management being implemented.

Efficiency analysis of container ports and terminals

OpenAIRE

Liu, Q.

2010-01-01

In the past two decades the steady growth of seaborne trade has resulted in the increase of container ships, container ports and their terminals. The structure of the shipping market is, moreover, continuously evolving. On the carrier side, shipping companies form consortia and alliances; on the port side, global terminal operators and dedicated container terminals are emerging. The aim of this research is to evaluate the efficiency of container ports and terminals and to study...

An analysis of the development of port operation in Da Nang Port, Vietnam

Science.gov (United States)

Nguyen, T. D. H.; Cools, M.

2018-04-01

This paper presents the current operating status in Da Nang Port, Vietnam in the period 2012-2016. The port operation had positive changes that were reflected by a significant increase in total throughputs, especially containerized cargo volumes. Classical decomposition techniques are used to find trend-cycle and seasonal components of monthly throughput flows. Appropriate predictive models of different kinds of throughputs are proposed. Finally, a development strategy towards containerization and investment policies in facilities, equipment, and infrastructure are suggested based on the predictive results.

Nuclear analysis of the ITER Cryopump Ports

International Nuclear Information System (INIS)

Moro, Fabio; Villari, Rosaria; Flammini, Davide; Antipenkov, Alexander; Dremel, Matthias; Levesy, Bruno; Loughlin, Michael; Juarez, Rafael; Perez, Lucia; Petrizzi, Luigino

2015-01-01

Highlights: • Evaluation the shielding effectiveness of the TCPHs by means of 3-D neutrons and gamma maps. • Assessment of the nuclear heating induced by neutron and photons on the TCP and TCPHs. • Calculation of the dose rate at 12 days after shutdown in the maintenance area of the Lower Ports with the Advanced D1S method, in order to verify the design target (100 μSv/h). • Potential improvements of the shielding configuration aimed at the reduction of the dose level in the Port Cell have been proposed and discussed. - Abstract: The ITER machine will be equipped with 6 torus Cryopumps (TCP) that are positioned in their housings (TCPH) and integrated into the cryostat walls at B1 level in the port cells. A comprehensive nuclear analysis of the Cryopump Ports #4 and #12 has been carried out by means of the MCNP-5 Monte Carlo code in a full 3-D geometry, providing guidelines for the design of the embedded components. Radiation transport calculations have been performed in order to determine the radiation field inside the Lower Ports, up the Port Cell: 3-D neutrons and gamma maps have been provided in order to evaluate the shielding effectiveness of the TCPHs. Nuclear heating induced by neutron and photons have been estimated on the TCP and TCPH to assess the nuclear loads during plasma operations. The shutdown dose rate in the maintenance area of the Lower Ports has been assessed with the Advanced D1S method to verify the design limits.

Nuclear analysis of the ITER Cryopump Ports

Energy Technology Data Exchange (ETDEWEB)

Moro, Fabio, E-mail: fabio.moro@enea.it [ENEA, Fusion Technical Unit, Nuclear Technologies Laboratory, Via Enrico Fermi 45, 00044 Frascati, Rome (Italy); Villari, Rosaria; Flammini, Davide [ENEA, Fusion Technical Unit, Nuclear Technologies Laboratory, Via Enrico Fermi 45, 00044 Frascati, Rome (Italy); Antipenkov, Alexander; Dremel, Matthias; Levesy, Bruno; Loughlin, Michael [ITER Organization, Route de Vinon sur Verdon, 13115 Saint Paul-lez-Durance (France); Juarez, Rafael; Perez, Lucia [UNED, Energetic Engineering Department, C/Juan del Rosal 12, Madrid (Spain); Petrizzi, Luigino [European Commission, DG Research & Innovation G5, CDMA 00/030, B-1049 Brussels (Belgium)

2015-10-15

Highlights: • Evaluation the shielding effectiveness of the TCPHs by means of 3-D neutrons and gamma maps. • Assessment of the nuclear heating induced by neutron and photons on the TCP and TCPHs. • Calculation of the dose rate at 12 days after shutdown in the maintenance area of the Lower Ports with the Advanced D1S method, in order to verify the design target (100 μSv/h). • Potential improvements of the shielding configuration aimed at the reduction of the dose level in the Port Cell have been proposed and discussed. - Abstract: The ITER machine will be equipped with 6 torus Cryopumps (TCP) that are positioned in their housings (TCPH) and integrated into the cryostat walls at B1 level in the port cells. A comprehensive nuclear analysis of the Cryopump Ports #4 and #12 has been carried out by means of the MCNP-5 Monte Carlo code in a full 3-D geometry, providing guidelines for the design of the embedded components. Radiation transport calculations have been performed in order to determine the radiation field inside the Lower Ports, up the Port Cell: 3-D neutrons and gamma maps have been provided in order to evaluate the shielding effectiveness of the TCPHs. Nuclear heating induced by neutron and photons have been estimated on the TCP and TCPH to assess the nuclear loads during plasma operations. The shutdown dose rate in the maintenance area of the Lower Ports has been assessed with the Advanced D1S method to verify the design limits.

Relationship beetween city-port-waterfront: complexity and complications

Directory of Open Access Journals (Sweden)

Bianca Petrella

2014-01-01

Full Text Available Water is the basis of human and urban civilization; transport is the basis of trade and therefore of social progress. For many centuries water was by far the most important mode of transport, this is the principle reason why cities with rivers or seaports were predominant over cities without such features.Initially, industrialization, the construction of the railways, the advent of the car and the beginning of air transport challenged the hegemonic role of the cities-port. However, since the introduction of containers in the mid-1950‘s and shortly after the construction of inter-ports the role of water transport has been revitalized.The containers and the enormous ships carrying them need great surface areas and long piers, so ports were moved outside of cities and, thus, the historical relationship between city and port was definitively broken.The decline of large parts of the urban water front triggered redevelopment initiatives, which over time changed their use from industrial to leisure. These initiatives were often given names such as ‘urban recovery’, ‘renewal’, ‘regeneration’, ‘redevelopment’, and so forth.Enormous leisure areas were the common denominator and often the buildings had an exclusive and, for this reason, homologated architecture designed by “archi-star” (famous architects. The new built-up areas were out of the local character and out of the historical city-port relationship.Almost always liberated port spaces remain the property of the Port Authority and for this reason the way of making decisions is difficult. Italian law provides for a set of governing bodies to decide how to plan the interventions in the port areas. However, the law does not impose a co-ordination of the border area between city and port. Thus, the good governance of this area is left to chance and the hope that the various bodies can find mutually satisfying agreements.Some good and bad practices in various cities around the world

Fuzzy MCDM Approach for Evaluating Intangible Resources Affecting Port Service Quality

Directory of Open Access Journals (Sweden)

Ji Yeong Pak

2015-12-01

Full Text Available Intangible resources consist of soft resources such as knowledge, information and capabilities. It is important for ports to enhance intangible as well as tangible resources to obtain sustainable competitive advantage. In this connection, this study aims to identify port intangible resources which may contribute to the delivery of port service quality and to propose a fuzzy TOPSIS approach to solve the port choice problem focusing on intangible resources. Fuzzy TOPSIS is appropriate to assist decision making with ambiguous and uncertain problems such as port choice with respect to intangible resources. In this paper, five port intangible resources were identified and evaluated and five leading container ports in the Asia-Pacific region were assessed in terms of their intangible resources. A survey questionnaire was sent to 21 experts who are working in shipping companies in Korea and involved in the selection of ports. It was found that customer and relational resource contributes most to the delivery of port service quality while Hong Kong appeared to be the port where intangible resources were most highly evaluated. This research helps to enrich the literature on port service quality and port choice evaluation. Its findings can also be used as guidelines for port managers to prioritise resources that may have greater influence on the delivery of port service quality and the subsequent training and education programs.

Rotterdam as a World Port City

NARCIS (Netherlands)

Wouter Jacobs; Menno Huijs; Isabelle Vries

2015-01-01

Most studies and models on the port-city interface focus on the inevitable process in which ports and cities grow apart, both spatially and economically. What is often overlooked is the relationships that remain in the form of maritime business services (finance, insurance, legal). These maritime

Complications after implantation of subcutaneous central venous ports (PowerPortⓇ

Directory of Open Access Journals (Sweden)

Takatoshi Nakamura

2017-05-01

Conclusion: PowerPort is a multifunctional port. Benign disease was a risk factor for postoperative complications. Because many types of subcutaneously implanted ports are used in our hospital, we had to inform the hospital staff about the functions of PowerPort.

Final design of ITER port plug test facility

Energy Technology Data Exchange (ETDEWEB)

Cerisier, Thierry, E-mail: thierry.cerisier@yahoo.fr [ITER Organization, Route de Vinon-sur-Verdon, CS 90046, St Paul-lez-Durance Cedex, 13067 (France); Levesy, Bruno [ITER Organization, Route de Vinon-sur-Verdon, CS 90046, St Paul-lez-Durance Cedex, 13067 (France); Romannikov, Alexander [Institution “Project Center ITER”, Kurchatov sq. 1, Building 3, Moscow 123182 (Russian Federation); Rumyantsev, Yuri [JSC “Cryogenmash”, Moscow reg., Balashikha 143907 (Russian Federation); Cordier, Jean-Jacques; Dammann, Alexis [ITER Organization, Route de Vinon-sur-Verdon, CS 90046, St Paul-lez-Durance Cedex, 13067 (France); Minakov, Victor; Rosales, Natalya; Mitrofanova, Elena [JSC “Cryogenmash”, Moscow reg., Balashikha 143907 (Russian Federation); Portone, Sergey; Mironova, Ekaterina [Institution “Project Center ITER”, Kurchatov sq. 1, Building 3, Moscow 123182 (Russian Federation)

2016-11-01

Highlights: • We introduce the port plug test facility (purpose and status of the design). • We present the PPTF sub-systems. • We present the environmental and functional tests. • We present the occupational and nuclear safety functions. • We conclude on the achievements and next steps. - Abstract: To achieve the overall ITER machine availability target, the availability of diagnostics and heating port plugs shall be as high as 99.5%. To fulfill this requirement, it is mandatory to test the port plugs at operating temperature before installation on the machine and after refurbishment. The ITER port plug test facility (PPTF) is composed of several test stands that can be used to test the port plugs whereas at the end of manufacturing (in a non-nuclear environment), or after refurbishment in the ITER hot cell facility. The PPTF provides the possibility to perform environmental (leak tightness, vacuum and thermo-hydraulic performances) and functional tests (radio frequency acceptance tests, behavior of the plugs’ steering mechanism and calibration of diagnostics) on upper and equatorial port plugs. The final design of the port plug test facility is described. The configuration of the standalone test stands and the integration in the hot cell facility are presented.

Severe Neutropenia at the Time of Implantable Subcutaneous Chest Port Insertion Is Not a Risk Factor for Port Removal at a Tertiary Pediatric Center.

Science.gov (United States)

Hoss, Daniel R; Bedros, Antranik A; Mesipam, Avinash; Criddle, Jared; Smith, Jason C

2017-03-01

To determine if severe neutropenia at the time of chest port insertion is a risk factor for port removal and central catheter-associated bloodstream infection (CCABSI) in pediatric patients. From May 2007 to June 2015, 183 consecutive patients (mean age, 9.9 y; range, 0.75-21 y) had a port inserted at a single tertiary pediatric center. Seventy-two had severe neutropenia at the time of port insertion (absolute neutrophil count [ANC] range, 0-500/mm 3 ; mean, 185/mm 3 ). Follow-up until port removal or death and CCABSI events were recorded. Within the first 30 days, similar incidences of CCABSI (12.5% of patients with severe neutropenia [n = 9] vs 4.5% of patients without [n = 5]), port removal for infection (2.8% [n = 2] vs 2.7% [n = 3]), and local port infection (2.8% [n = 2] vs 0.9% [n = 1]) were observed in both groups (P > .05), but the rate of CCABSI per 1,000 catheter-days was higher for patients with severe neutropenia (P = .045). Overall, similar incidences of CCABSI (18.1% [n = 13] vs 16.2% [n = 18]), port removal for infection (2.8% [n = 2] vs 7.2% [n = 8]), local port infection (2.8% [n = 2] vs 2.7% [n = 3]), and CCABSIs per 1,000 catheter-days (0.332 vs 0.400) were observed in both groups (P > .05). Port placement in patients with severe neutropenia can be performed without an increased incidence of port removal for infection. The majority of CCABSIs were successfully treated without port removal. Copyright © 2016 SIR. Published by Elsevier Inc. All rights reserved.

EVALUATING THE COMPETITION DYNAMICS OF CONTAINER PORTS IN THE NORTH ADRIATIC

OpenAIRE

Twrdy, Elen; Batista, Milan

2014-01-01

World trade has changed in the last decade and the container traffic flows are oriented towards several parts of the European continent. A European container port system is not a homogenous set of ports, but is established of several large ports (Rotterdam, Hamburg, Algeciras...) and a large number of medium- and small-sized ports. North Adriatic (NA) ports belong to this category of ports and in this paper we have analysed the container flows and the throughput attained in these ports.

78 FR 36014 - Deepwater Port License Application: Liberty Natural Gas, LLC, Port Ambrose Deepwater Port

Science.gov (United States)

2013-06-14

... timeline for processing an application. When MarAd and USCG determine that an application contains the... that Port Ambrose falls within the proposed area of interest for the New York Power Authority Long Island-New York City Offshore Wind Project. This project will be acknowledged and considered in the...

Is single port enough in minimally surgery for pneumothorax?

Science.gov (United States)

Ocakcioglu, Ilhan; Alpay, Levent; Demir, Mine; Kiral, Hakan; Akyil, Mustafa; Dogruyol, Talha; Tezel, Cagatay; Baysungur, Volkan; Yalcinkaya, Irfan

2016-01-01

Video-assisted thoracoscopic surgery is a widespread used procedure for treatment of primary spontaneous pneumothorax patients. In this study, the adaptation of single-port video-assisted thoracoscopic surgery approach to primary spontaneous pneumothorax patients necessitating surgical treatment, with its pros and cons over the traditional two- or three-port approaches are examined. Between January 2011 and August 2013, 146 primary spontaneous pneumothorax patients suitable for surgical treatment are evaluated prospectively. Indications for surgery included prolonged air leak, recurrent pneumothorax, or abnormal findings on radiological examinations. Visual analog scale and patient satisfaction scale score were utilized. Forty triple-port, 69 double-port, and 37 single-port operations were performed. Mean age of 146 (126 male, 20 female) patients was 27.1 ± 16.4 (range 15-42). Mean operation duration was 63.59 ± 26 min; 61.7 for single, 64.2 for double, and 63.8 min for triple-port approaches. Total drainage was lower in the single-port group than the multi-port groups (P = 0.001). No conversion to open thoracotomy or 30-day hospital mortality was seen in our group. No recurrence was seen in single-port group on follow-up period. Visual analog scale scores on postoperative 24th, 48th, and 72nd hours were 3.42 ± 0.94, 2.46 ± 0.81, 1.96 ± 0.59 in the single-port group; significantly lower than the other groups (P = 0.011, P = 0.014, and P = 0.042, respectively). Patient satisfaction scale scores of patients in the single-port group on 24th and 48th hours were 1.90 ± 0.71 and 2.36 ± 0.62, respectively, indicating a significantly better score than the other two groups (P = 0.038 and P = 0.046). This study confirms the competency of single-port procedure in first-line surgical treatment of primary spontaneous pneumothorax.

Interfacing external sensors with Android smartphones through near field communication

International Nuclear Information System (INIS)

Leikanger, Tore; Häkkinen, Juha; Schuss, Christian

2017-01-01

In this paper, we present and evaluate a new approach to communicate with inter-integrated circuit (I2C) enabled circuits such as sensors over near field communication (NFC). The NFC-to-I2C interface was designed using a non-standard NFC command to control the I2C bus directly from a smartphone, which was controlling both, the read and write operations on the I2C bus. The NFC-to-I2C interface was reporting back the data bytes on the bus to the smartphone when the transaction was completed successfully. The proposed system was tested experimentally, both, with write and read requests to a commercial microcontroller featuring a hardware I2C port, as well as reading a commercial I2C enabled humidity and temperature sensor. We present experimental results of the system which show that our approach enables an easy interface between smartphones and external sensors. Interfacing external sensors is useful and beneficial for smartphone users, especially, if certain types of sensors are not available on smartphones. (paper)

Single-port laparoscopic myomectomy using a new single-port transumbilical morcellation system: initial clinical study.

Science.gov (United States)

Kim, Yong-Wook; Park, Byung-Joon; Ro, Duck-Yeong; Kim, Tae-Eung

2010-01-01

To evaluate the feasibility of single-port laparoscopic myomectomy with transumbilical morcellation and suturing. Continuing prospective study (Canadian Task Force classification II-3). University hospital. Fifteen patients who underwent single-port laparoscopic myomectomy between September 2008 and October 2009 to remove single or multiple uterine myomas, at least 1 in each patient measuring greater than 4 cm in diameter. All single-port laparoscopic myomectomy procedures were performed by a single surgeon (Dr. Y.W. Kim). Myomas were extracted transumbilically by cutting the myomas into smaller pieces with a knife or a conventional electromechanical morcellator. After making a single 1.5- to 2.0-cm umbilical incision, the single-port system, created with a wound retractor and a surgical glove, was inserted. All operations were performed using conventional rigid straight laparoscopic instruments. Laparoscopic suturing was performed in intramural myomas and some subserosal myomas. Patient mean (SD; range) age was 38.3 (5.6; 29-49) years. The number of myomas per patient was 1.6 (1.4; 1-6). The diameter of the largest myomas was 6.1 (1.5; 4.2-9.6) cm. In 4 patients, only a knife was required for transumbilical extraction of myomas, and in 11 patients, transumbilical morcellation with an electromechanical morcellator with or without a knife was used. Transumbilical drainage tubes were inserted into the pelvic cavity in 11 of 15 patients. Operative time was 96.7 (33.8; 35-150) minutes. The decrease in postoperative hemoglobin concentration was 1.8 (1.2; 0.4-3.6) g/dL. During the operations, no patients required blood transfusion. No patients developed postoperative fever. Neither bowel injury nor urinary tract injury occurred in any patient. The postoperative hospital stay was 3.1 (0.8; 2-4) days. Single-port transumbilical morcellation using a conventional electromechanical morcellator with or without a knife is feasible. Single-port laparoscopic myomectomy is an

Free Port of Vladivostok: Development Conditions, Prospects, Risks

Directory of Open Access Journals (Sweden)

Elena Viktorovna Krasova

2015-12-01

Full Text Available One of the priority directions of Russia’s state policy with regard to territories’ development is the development of the Far Eastern region. The free port of Vladivostok is one of the key projects that are currently being implemented in the southern part of Primorsky Krai and they focus on boosting the socio-economic development of Vladivostok city, Primorsky Krai and the Far Eastern region as a whole. The goal of this research is to consider the conceptual issues of the free port of Vladivostok, to outline the conditions and prospects of its operation and identify risks associated with its future development. The article defines the modern concept of “free port”, characterizes historical experience of the “free port” regime in Vladivostok in the end of the 19th century, substantiates the strategic importance of using the free port of Vladivostok as a tool of intensive growth of Russian Far Eastern territories. The article also discloses the essence of the free port of Vladivostok as a means to promote free entrepreneurship, which is used to increase freight traffic through the port of Vladivostok, increase foreign trade, attract new investments, create new industries and develop the port’s infrastructure. The article provides a review of the main tax benefits and perspectives of the free port of Vladivostok in terms of the gross regional product formation. Analyzing the mechanisms of effective functioning of the free port of Vladivostok, the authors identify the short-term (mid-term and long-term priorities and operational risks for the free port of Vladivostok. The article also touches upon some issues concerning the response of some foreign countries to the creation of the free port of Vladivostok

On Distributed Port-Hamiltonian Process Systems

NARCIS (Netherlands)

Lopezlena, Ricardo; Scherpen, Jacquelien M.A.

2004-01-01

In this paper we use the term distributed port-Hamiltonian Process Systems (DPHPS) to refer to the result of merging the theory of distributed Port-Hamiltonian systems (DPHS) with the theory of process systems (PS). Such concept is useful for combining the systematic interconnection of PHS with the

Intracorporeal hybrid single port vs conventional laparoscopic appendectomy in children

Directory of Open Access Journals (Sweden)

Paul Anthony Karam

2016-12-01

Full Text Available Transumbilical laparoscopic assisted appendectomy combines laparoscopic single port dissection with open appendectomy after exteriorization of the appendix through the port site. Compared to the conventional three-port approach, this technique provides an alternative with excellent cosmetic outcome. We developed a safe and effective technique to perform an intracorporeal single port appendectomy, using the same laparoscope employed in the extracorporeal procedure. Retrospective review of 71 consecutively performed intracorporeal single port appendectomies and 30 conventional three-port appendectomies in children 6 to 17 years of age. A straight 10-mm Storz telescope with inbuilt 6 mm working channel is used to dissect the appendix, combined with one port-less 2.3 mm percutaneous grasper. Polymer WECK® hem-o-lock® clips are applied to seal the base of the appendix and the appendiceal vessels. No intraoperative complications were reported with the hybrid intracorporeal single port appendectomy or three-port appendectomy. There were two post-operative complications in the group treated with the single port hybrid technique: one intra-abdominal abscess and one surgical site infection. Groups did not differ in age, weight, and types of appendicitis. Operative times were shorter for the hybrid technique (70 vs 79 minutes but did not differ significantly (P=0.19. This modified technique to a previously described single port extracorporeal appendectomy is easy to master and implement. It provides exposure similar to a three-port laparoscopic appendectomy, while maintaining virtually scarless results and potentially reduces the risk for surgical site infections compared to the extracorporeal technique.

33 CFR 165.761 - Security Zones; Port of Palm Beach, Port Everglades, Port of Miami, and Port of Key West, Florida.

Science.gov (United States)

2010-07-01

... of the law enforcement boats and cruise ship tenders which will mark a transit lane in channel. (ii... east of the law enforcement vessels and cruise ship tenders, which will mark a transit lane in the..., tug boats and contracted security vessels may assist the Coast Guard Captain of the Port under the...

The Port Service Ecosystem Research Based on the Lotka-Volterra Model

Directory of Open Access Journals (Sweden)

Li Wenjuan

2017-11-01

Full Text Available Under the new normal of China’s economy, the competition among the port enterprises is not only the competition of the core competence of the port, the port industry chain or the port supply chain, but also the competition of the port service ecosystem. In this paper, the concept and characteristics of the port service ecosystem is discussed, a hierarchical model of the port service ecosystem is constructed. As an extended logistic model, Lotka-Volterra model is applied to study the competitive co-evolution and mutually beneficial co-evolution of enterprises in the port service ecosystem. This paper simulates the co-evolution of enterprises in the port service ecosystem by using MATLAB programming. The simulation results show that the breadth of the niche of the enterprises is changing with the change of the competition coefficient and the coefficient of mutual benefit in the port service ecosystem. Based on that, some proposals are put forward to ensure the healthy and orderly development of the port service ecosystem.

FIRST SINGLE-PORT LAPAROSCOPIC PANCREATECTOMY IN BRAZIL

Directory of Open Access Journals (Sweden)

Marcel Autran Cesar MACHADO

2013-12-01

Full Text Available Context Pancreatic surgery is an extremely challenging field, and the management of pancreatic diseases continues to evolve. In the past decade, minimal access surgery is moving towards minimizing the surgical trauma by reducing numbers and size of the port. In the last few years, a novel technique with a single-incision laparoscopic approach has been described for several laparoscopic procedures. Objectives We present a single-port laparoscopic spleen-preserving distal pancreatectomy. To our knowledge, this is the first single-port pancreatic resection in Brazil and Latin America. Methods A 33-year-old woman with neuroendocrine tumor underwent spleen-preserving distal pancreatectomy via single-port approach. A single-incision advanced access platform with gelatin cap, self-retaining sleeve and wound protector was used. Results Operative time was 174 minutes. Blood loss was minimal, and the patient did not receive a transfusion. The recovery was uneventful, and the patient was discharged on postoperative day 4. Conclusions Single-port laparoscopic spleen-preserving distal pancreatectomy is feasible and can be safely performed in specialized centers by skilled laparoscopic surgeons.

Specialization and Flexibility in Port Cargo Handling

Directory of Open Access Journals (Sweden)

Hakkı KİŞİ

2016-11-01

Full Text Available Cargo handling appears to be the fundamental function of ports. In this context, the question of type of equipment and capacity rate need to be tackled with respect to cargo handling principles. The purpose of this study is to discuss the types of equipment to be used in ports, relating the matter to costs and capacity. The question is studied with a basic economic theoretical approach. Various conditions like port location, size, resources, cargo traffic, ships, etc. are given parameters to dictate the type and specification of the cargo handling equipment. Besides, a simple approach in the context of cost capacity relation can be useful in deciding whether to use specialized or flexible equipment. Port equipment is sometimes expected to be flexible to handle various types of cargo as many as possible and sometimes to be specialized to handle one specific type of cargo. The cases that might be suitable for those alternatives are discussed from an economic point of view in this article. Consequently, effectiveness and efficiency criteria play important roles in determining the handling equipment in ports.

Laser treatment of Port-wine stains

OpenAIRE

Boffa, Michael J.

2001-01-01

A state-of-the-art pulsed dye laser machine to treat port-wine stains and other vascular lesions has been available in the Malta Health Service since 1999. This article reviews the pathophysiology and clinical features of port- wine stains and describes the principles of laser treatment for this condition.

Prefab-Interiority

DEFF Research Database (Denmark)

Frier, Marie; Fisker, Anna Marie; Kirkegaard, Poul Henning

2010-01-01

qualities is significantly dependent on our constructive ability to economically and production-technically join building elements. Consequently this paper explores the potential for developing interiority as a theory and design principle for transforming constructive challenges within prefab practice....../S. As a research result the paper suggests a positioning of interiority as a theory and design principle for developing a sensuous prefab practice......., and practical realm of prefabrication, leaving the produced houses as monotonous box-like constructions rather than inhabitable homes. But what are the sensuous qualities actually spatially defining a home, and how to formulate design principles for developing and revealing these qualities within prefab...

Optimal location of dry ports in the Pan-Pearl River Delta

Directory of Open Access Journals (Sweden)

Wu Qitao

2017-01-01

Full Text Available Dry ports have become a very important part of globalization and a cornerstone in port competitiveness. Based on the analytic hierarchy process, this paper established the dry port index system to evaluate the potential location of dry ports linked to the port system in the Pearl River Delta, in a case study covering 115 cities in the Pan - Pearl River Delta. The results show that it is optimal to locate 21 dry ports in the research region, and each dry port serves different areas. There are 4 optimal transport corridors for the dry port logistic network, including Guangzhou- Kunming transport corridor, Guangzhou-Chengdu transport corridor, Guangzhou-Changsha transport corridor and Shenzhen-Nanchang transport corridor.

Miniature large range multi-axis force-torque sensor for biomechanical applications

International Nuclear Information System (INIS)

Brookhuis, R A; Sanders, R G P; Ma, K; Lammerink, T S J; De Boer, M J; Krijnen, G J M; Wiegerink, R J

2015-01-01

A miniature force sensor for the measurement of forces and moments at a human fingertip is designed and realized. Thin silicon pillars inside the sensor provide in-plane guidance for shear force measurement and provide the spring constant in normal direction. A corrugated silicon ring around the force sensitive area provides the spring constant in shear direction and seals the interior of the sensor. To detect all load components, capacitive read-out is used. A novel electrode pattern results in a large shear force sensitivity. The fingertip force sensor has a wide force range of up to 60 N in normal direction, ± 30 N in shear direction and a torque range of ± 25 N mm. (paper)

Comparison of differences between ports for radioactive material transport

International Nuclear Information System (INIS)

Massey, C.D.; Wheeler, T.A.; Yoshimura, H.R.

1994-01-01

Recent controversy and litigation over the import/export of radioactive materials into and out of the United States via United States ports has centered on differences between ports, especially differences in surrounding population densities, and also whether reliance on one or a few ports poses unacceptable risks for these ports and the surrounding populations. This study examines the results of risk analyses from several recent environmental assessments dealing with import/export of various types of radioactive materials ranging from uranium hexafluoride to spent nuclear fuel. Since an intermodal transfer is always involved, the maritime and intermodal transportation is broken down into its component activities and segments; each is determined separately. The results indicate that most of the potential exposure occurs during routine handling of packages during intermodal transfer. Since handling of containerized cargo is highly standardized at ports around the world, differences between ports are of secondary importance. The risks associated with any overland transport from port to inland destination are primarily a function of distance for a given package type

Simulation model for port shunting yards

Science.gov (United States)

Rusca, A.; Popa, M.; Rosca, E.; Rosca, M.; Dragu, V.; Rusca, F.

2016-08-01

Sea ports are important nodes in the supply chain, joining two high capacity transport modes: rail and maritime transport. The huge cargo flows transiting port requires high capacity construction and installation such as berths, large capacity cranes, respectively shunting yards. However, the port shunting yards specificity raises several problems such as: limited access since these are terminus stations for rail network, the in-output of large transit flows of cargo relatively to the scarcity of the departure/arrival of a ship, as well as limited land availability for implementing solutions to serve these flows. It is necessary to identify technological solutions that lead to an answer to these problems. The paper proposed a simulation model developed with ARENA computer simulation software suitable for shunting yards which serve sea ports with access to the rail network. Are investigates the principal aspects of shunting yards and adequate measures to increase their transit capacity. The operation capacity for shunting yards sub-system is assessed taking in consideration the required operating standards and the measure of performance (e.g. waiting time for freight wagons, number of railway line in station, storage area, etc.) of the railway station are computed. The conclusion and results, drawn from simulation, help transports and logistics specialists to test the proposals for improving the port management.

PC interfacing using Centronics, RS232 and game ports

CERN Document Server

An, Pei

1998-01-01

The main links with your PC and the outside world are the centronic port, used for connecting the printer, the RS232 port, used for the mouse, and the games port for a joystick. This book explores how these input/output (I/O) ports can be put to use through a range of other interfacing applications. This is especially useful for laptop and palmtop PCs which cannot be fitted with internal I/O cards. A novel approach is taken by this book, combining the hardware through which the ports can be explored, and the software programming needed to carry out a range of experiments.Circuits are p

Fiber Optic Strain Sensor for Planetary Gear Diagnostics

Science.gov (United States)

Kiddy, Jason S.; Lewicki, David G.; LaBerge, Kelsen E.; Ehinger, Ryan T.; Fetty, Jason

2011-01-01

This paper presents a new sensing approach for helicopter damage detection in the planetary stage of a helicopter transmission based on a fiber optic strain sensor array. Complete helicopter transmission damage detection has proven itself a difficult task due to the complex geometry of the planetary reduction stage. The crowded and complex nature of the gearbox interior does not allow for attachment of sensors within the rotating frame. Hence, traditional vibration-based diagnostics are instead based on measurements from externally mounted sensors, typically accelerometers, fixed to the gearbox exterior. However, this type of sensor is susceptible to a number of external disturbances that can corrupt the data, leading to false positives or missed detection of potentially catastrophic faults. Fiber optic strain sensors represent an appealing alternative to the accelerometer. Their small size and multiplexibility allows for potentially greater sensing resolution and accuracy, as well as redundancy, when employed as an array of sensors. The work presented in this paper is focused on the detection of gear damage in the planetary stage of a helicopter transmission using a fiber optic strain sensor band. The sensor band includes an array of 13 strain sensors, and is mounted on the ring gear of a Bell Helicopter OH-58C transmission. Data collected from the sensor array is compared to accelerometer data, and the damage detection results are presented

Regional Hub port development : the case of Montevideo, Uruguay

OpenAIRE

Wilmsmeier, Gordon; Martínez Zarzoso, Inmaculada; Fiess, Norbert

2011-01-01

This paper reflects on port development in Uruguay in an environment of trilateral interport competition. The regional characteristics of port development in terms of their geographical, functional and operational characteristics are discussed by analysing the port system’s evolution. The case of Montevideo as the success or failure of a regional hub port development strategy is analysed in detail. Particular attention is given to the evolution and impact of the liner shipping service network...

Int-Soft Interior Hyperideals of Ordered Semihypergroups

Directory of Open Access Journals (Sweden)

Asghar Khan

2017-07-01

Full Text Available The main theme of this paper is to study ordered semihypergroups in the context of int-soft interior hyperideals. In this paper, the notion of int-soft interior hyperideals are studied and their related properties are discussed. We present characterizations of interior hyperideals in terms of int-soft interior hyperideals. The concepts of int-soft hyperideals and int-soft interior hyperideals coincide in a regular as well as in intra-regular ordered semihypergroups. We prove that every int-soft hyperideal is an int-soft interior hyperideal but the converse is not true which is shown with help of an example. Furthermore we characterize simple ordered semihypergroups by means of int-soft hyperideals and int-soft interior hyperideals.

77 FR 47522 - Special Local Regulation; Port Huron Offshore Gran Prix, St. Clair River; Port Huron, MI

Science.gov (United States)

2012-08-09

... 13045, Protection of Children from Environmental Health Risks and Safety Risks. This rule is not an economically significant rule and does not create an environmental risk to health or risk to safety that may...-AA08 Special Local Regulation; Port Huron Offshore Gran Prix, St. Clair River; Port Huron, MI AGENCY...

Ecological risk assessments for the baseline condition for the Port Hope and Port Granby Projects

International Nuclear Information System (INIS)

Hart, D.R.; Kleb, H.

2006-01-01

Baseline ecological risk assessments were completed in and around the areas where cleanup of low-level radioactive waste (LLRW) and marginally contaminated soil (MCS) is planned under the Port Hope Area Initiative (PHAI). Both aquatic and terrestrial environments were assessed, in the vicinity of the proposed waste management facilities near Welcome and Port Granby, in locations potentially influenced by LLRW and MCS that will be cleaned up in future, and in reference locations that are not potentially influenced. The calculated doses and risk quotients suggest potential radiation effects for pre-cleanup benthic invertebrates in Port Hope Harbour, for any ducks feeding exclusively in this area, and for soil invertebrates in some other waste sites. In addition, risk quotients suggest potential baseline effects from some elements, particularly uranium and arsenic, in localized areas that are influenced by LLRW and MCS. (author)

Port Site Infections After Laparoscopic Cholecystectomy

Directory of Open Access Journals (Sweden)

Mumtaz KH Al-Naser

2017-06-01

Full Text Available Background: Port site infection (PSI is an infrequent surgical site infection that complicates laparoscopic surgery but has a considerable influence in the overall outcome of laparoscopic cholecystectomy. The aim of this study was to evaluate factors that influence PSI after laparoscopic cholecystectomies and to analyze which of these factors can be modified to avoid PSI in a trail to achieve maximum laparoscopic advantages. Methods: A prospective descriptive qualitative study conducted on patients who underwent laparoscopic cholecystectomies. Swabs were taken for culture & sensitivity in all patients who developed PSI. Exploration under general anaesthesia, for patients, had deep surgical site infections and wound debridement was done, excisional biopsies had been taken for histopathological studies, and tissue samples for polymerase chain reaction for detection of mycobacterium tuberculosis was done. All patients were followed up for six months postoperatively. Factors as gender, site of infected port, type of microorganism, acute versus chronic cholecystitis, type of infection (superficial or deep infection and intraoperative spillage of stones, bile or pus were analyzed in our sample. Results: Port site infection rate was recorded in 40/889 procedures (4.5%, higher rates were observed in male patients 8/89 (8.9%, in acute cholecystitis 13/125 (10.4%, when spillage of bile, stones or pus occurred 24/80 (30%, and at epigastric port 32/40 (80%. Most of the PSI were superficial infections 77.5% with non-specific microorganism 34/40 (85%. Conclusion: There is a significant association of port site infection with spillage of bile, stones, or pus, with the port of gallbladder extraction and with acute cholecystitis. Especial consideration should be taken in chronic deep surgical site infection as mycobacterium tuberculosis could be the cause. Most of the PSIs are superficial and more common in males.

An Energy-Efficient ASIC for Wireless Body Sensor Networks in Medical Applications.

Science.gov (United States)

Xiaoyu Zhang; Hanjun Jiang; Lingwei Zhang; Chun Zhang; Zhihua Wang; Xinkai Chen

2010-02-01

An energy-efficient application-specific integrated circuit (ASIC) featured with a work-on-demand protocol is designed for wireless body sensor networks (WBSNs) in medical applications. Dedicated for ultra-low-power wireless sensor nodes, the ASIC consists of a low-power microcontroller unit (MCU), a power-management unit (PMU), reconfigurable sensor interfaces, communication ports controlling a wireless transceiver, and an integrated passive radio-frequency (RF) receiver with energy harvesting ability. The MCU, together with the PMU, provides quite flexible communication and power-control modes for energy-efficient operations. The always-on passive RF receiver with an RF energy harvesting block offers the sensor nodes the capability of work-on-demand with zero standby power. Fabricated in standard 0.18-¿m complementary metal-oxide semiconductor technology, the ASIC occupies a die area of 2 mm × 2.5 mm. A wireless body sensor network sensor-node prototype using this ASIC only consumes < 10-nA current under the passive standby mode, and < 10 ¿A under the active standby mode, when supplied by a 3-V battery.

Towards port sustainability through probabilistic models: Bayesian networks

Directory of Open Access Journals (Sweden)

B. Molina

2018-04-01

Full Text Available It is necessary that a manager of an infrastructure knows relations between variables. Using Bayesian networks, variables can be classified, predicted and diagnosed, being able to estimate posterior probability of the unknown ones based on known ones. The proposed methodology has generated a database with port variables, which have been classified as economic, social, environmental and institutional, as addressed in of smart ports studies made in all Spanish Port System. Network has been developed using an acyclic directed graph, which have let us know relationships in terms of parents and sons. In probabilistic terms, it can be concluded from the constructed network that the most decisive variables for port sustainability are those that are part of the institutional dimension. It has been concluded that Bayesian networks allow modeling uncertainty probabilistically even when the number of variables is high as it occurs in port planning and exploitation.

PERFORMANCE ASSESSMENT IN OPERATING DRY PORTS

Directory of Open Access Journals (Sweden)

Ciortescu Cezar-Gabriel

2010-12-01

Full Text Available In this paper, an approach for recognizing and defining correct and operable performance will be presented with the purpose of evaluating the effectiveness and efficiency of processes in dry ports (inland intermodal hubs. The challenge in evaluating the possible improvements of the underlying processes lies in the special nature and the complex structure of dry ports. It is important to consider that all the processes are highly interconnected and that changes in parameters in one process also have an impact on parameters in other processes. Furthermore, the performance of dry ports, seen as the backbone of the system, has a significant impact on the overall performance of the whole transportation network.

U.S. port commerce in radioactive materials

International Nuclear Information System (INIS)

Marti, B.E.

1987-01-01

Much attention has focused on the movement of radioactive materials over land transport systems. On the other hand, maritime flow and associated throughput studies of such substances have been neglected. Although several peaks and troughs are evident between 1972 and 1981, radioactive tonnage moving through U.S. port facilities steadily increasing. In the ten-year period assessed, total radioactive materials handled at U.S. ports expanded by over 19,000 tons, which amounts to almost a 173 percent growth rate. The purpose of this exploratory research is threefold. First, it identifies all U.S. ports which were involved in loading or discharging radioactive materials. The major goal of the identification process is to broaden public awareness of these types of movement. Second, it classifies U.S. seaports based on the magnitude of radioactive tonnage handled. The function of the classification is to impose some order on the varied data, while at the same time categorizing large, medium, and small facilities. Finally, it seeks to verify whether or not a long term trend exists. The objective of the verification process is to ascertain if the distribution of radioactive materials handled at individual ports has remained constant. Port safety and contingency planning are clearly within the purview of coastal zone management. The results of this preliminary research should form a foundation for future studies which compare and evaluate local, state, and federal regulatory policy pertaining to port operations involving radioactive materials, including waste

Hub port competition and welfare effects of strategic privatization

NARCIS (Netherlands)

Czerny, A.I.; Hoffler, F.; Mun, S.

2014-01-01

Private operation of port facilities is becoming increasingly common worldwide. We investigate the effect of port privatization in a setting with two ports located in different countries, each serving their home market but also competing for the transshipment traffic from a third region. Each

Desain Interior Gedung Kesenian Jakarta

Directory of Open Access Journals (Sweden)

Sri Rachmayanti

2011-04-01

Full Text Available The purpose of this study was to examine the interior design of Gedung Kesenian Jakarta in detail. Another thing is to obtain complete data and analyze the interior design development of GKJ.  This study will described in terms of design style and different designs since the early period of this building, the arrival of the Dutch until the present era. Besides aesthetic of interior design, it will review technical factors in the building that related to its interior design, such as acoustic, air conditioning, lighting system, sound system. This research is based on data literartures and interviews with the GKJ. In conclusion, it will discuss the existence of GKJ in relation to local identity, culture and heritage.   

The Aggregate Planning For Trucking Operation in Cikarang Dry Port

Directory of Open Access Journals (Sweden)

Dwi Puspita Sari Utami

2015-06-01

Full Text Available Abstract. Cikarang Dry Port currently is the only dry port in Indonesia. This Dry Port has a role to connect or extend the Sea Port to the industrial areas located far from Sea Port. Thus, it creates a value added and also reduce costs. One of the operations done in Cikarang Dry Port is trucking operation. This research aims to examine the planning of 2014 trucking activity in Cikarang Dry Port to determine the right number of the truck that will be best occupied to manage all demands. The analysis begins with demand forecasting by using a moving average method of 12 months or one year period in 2013 which will be used as main information to develop the plans. There are three plans developed in this research. Based on the three plans, Plan A with minimum trucking plan with subcontracting is the most profitable which gives the highest profitability of Rp. 374,984,625. Recommendation for this research is using the current minimum number of 39 trucks rent with additional subcontracting when the demand is exceeding the capacity, thus, Cikarang Dry Port can occupy all demands and gain more profits. Keywords: Aggregate Planning; Scheduling; Trucking Operation; Moving Average; Cikarang Dry Port

The Aggregate Planning For Trucking Operation in Cikarang Dry Port

Directory of Open Access Journals (Sweden)

Dwi Puspita Sari Utami

2015-07-01

Full Text Available Abstract. Cikarang Dry Port currently is the only dry port in Indonesia. This Dry Port has a role to connect or extend the Sea Port to the industrial areas located far from Sea Port. Thus, it creates a value added and also reduce costs. One of the operations done in Cikarang Dry Port is trucking operation. This research aims to examine the planning of 2014 trucking activity in Cikarang Dry Port to determine the right number of the truck that will be best occupied to manage all demands. The analysis begins with demand forecasting by using a moving average method of 12 months or one year period in 2013 which will be used as main information to develop the plans. There are three plans developed in this research. Based on the three plans, Plan A with minimum trucking plan with subcontracting is the most profitable which gives the highest profitability of Rp. 374,984,625. Recommendation for this research is using the current minimum number of 39 trucks rent with additional subcontracting when the demand is exceeding the capacity, thus, Cikarang Dry Port can occupy all demands and gain more profits.Keywords: Aggregate Planning; Scheduling; Trucking Operation; Moving Average; Cikarang Dry Port

The construction strategy and measures for ecological analysis of China's ports

Science.gov (United States)

Zhang, Lu; Zhao, Junjie; Shou, Youping; Wang, Ning; Qiao, Jianzhe; Tian, Mingjing

2018-04-01

The Port is an important transport hub, one of the important infrastructure of the national economy, the corresponding regional development has a great role in promoting.The construction of the port has been developed rapidly, but it has also brought about more serious environmental problems. Therefore, this paper discusses the nature of ecological ports, summarized the experience of ecological protection measures on the international advanced ports and port construction ecology. The central idea is to explore the construction of ecological port ideas and development countermeasures.

Advances in SAW gas sensors based on the condensate-adsorption effect.

Science.gov (United States)

Liu, Jiuling; Wang, Wen; Li, Shunzhou; Liu, Minghua; He, Shitang

2011-01-01

A surface-acoustic-wave (SAW) gas sensor with a low detection limit and fast response for volatile organic compounds (VOCs) based on the condensate-adsorption effect detection is developed. In this sensor a gas chromatography (GC) column acts as the separator element and a dual-resonator oscillator acts as the detector element. Regarding the surface effective permittivity method, the response mechanism analysis, which relates the condensate-adsorption effect, is performed, leading to the sensor performance prediction prior to fabrication. New designs of SAW resonators, which act as feedback of the oscillator, are devised in order to decrease the insertion loss and to achieve single-mode control, resulting in superior frequency stability of the oscillator. Based on the new phase modulation approach, excellent short-term frequency stability (±3 Hz/s) is achieved with the SAW oscillator by using the 500 MHz dual-port resonator as feedback element. In a sensor experiment investigating formaldehyde detection, the implemented SAW gas sensor exhibits an excellent threshold detection limit as low as 0.38 pg.

Are we connected? : Ports in Global Networks

NARCIS (Netherlands)

R.A. Zuidwijk (Rob)

2015-01-01

markdownabstractAbstract Global supply chains are built on organizational, information, and logistics networks. Ports are connected via these networks and also need to connect these networks. Synchromodality is an innovative concept for container transportation, and the port plays an important

A high-performance lab-on-a-chip liquid sensor employing surface acoustic wave resonance

Science.gov (United States)

Kustanovich, K.; Yantchev, V.; Kirejev, V.; Jeffries, G. D. M.; Lobovkina, T.; Jesorka, A.

2017-11-01

We demonstrate herein a new concept for lab-on-a-chip in-liquid sensing, through integration of surface acoustic wave resonance (SAR) in a one-port configuration with a soft polymer microfluidic delivery system. In this concept, the reflective gratings of a one-port surface acoustic wave (SAW) resonator are employed as mass loading-sensing elements, while the SAW transducer is protected from the measurement environment. We describe the design, fabrication, implementation, and characterization using liquid medium. The sensor operates at a frequency of 185 MHz and has demonstrated a comparable sensitivity to other SAW in-liquid sensors, while offering quality factor (Q) value in water of about 250, low impedance and fairly low susceptibility to viscous damping. For proof of principle, sensing performance was evaluated by means of binding 40 nm neutravidin-coated SiO2 nanoparticles to a biotin-labeled lipid bilayer deposited over the reflectors. Frequency shifts were determined for every step of the affinity assay. Demonstration of this integrated technology highlights the potential of SAR technology for in-liquid sensing.

Vectorization, parallelization and porting of nuclear codes. 2001

International Nuclear Information System (INIS)

Akiyama, Mitsunaga; Katakura, Fumishige; Kume, Etsuo; Nemoto, Toshiyuki; Tsuruoka, Takuya; Adachi, Masaaki

2003-07-01

Several computer codes in the nuclear field have been vectorized, parallelized and transported on the super computer system at Center for Promotion of Computational Science and Engineering in Japan Atomic Energy Research Institute. We dealt with 10 codes in fiscal 2001. In this report, the parallelization of Neutron Radiography for 3 Dimensional CT code NR3DCT, the vectorization of unsteady-state heat conduction code THERMO3D, the porting of initial program of MHD simulation, the tuning of Heat And Mass Balance Analysis Code HAMBAC, the porting and parallelization of Monte Carlo N-Particle transport code MCNP4C3, the porting and parallelization of Monte Carlo N-Particle transport code system MCNPX2.1.5, the porting of induced activity calculation code CINAC-V4, the use of VisLink library in multidimensional two-fluid model code ACD3D and the porting of experiment data processing code from GS8500 to SR8000 are described. (author)

The State of Environmentally Sustainable Interior Design Practice

OpenAIRE

Mihyun Kang; Denise A. Guerin

2009-01-01

Problem statement: Research that investigates how interior designers use environmentally sustainable interior design criteria in their design solutions has not been done. To provide a base to develop education strategies for sustainable interior design, this study examined the state of environmentally sustainable interior design practice. Approach: A national, Internet-based survey of interior design practitioners was conducted. To collect data, the random sample of US interior design practit...

Cyber security in ports : Business as usual

NARCIS (Netherlands)

Moerel, Lokke; Dezeure, Freddy

2017-01-01

Our paper summarizes the risks and provides concrete and pragmatic proposals to increase substantially the cyber maturity and resilience in the ports by organizing training and awareness raising, fostering cooperation and information exchange both between the stakeholders in the ports and across the

Neutronics analysis for integration of ITER diagnostics port EP10

Energy Technology Data Exchange (ETDEWEB)

Colling, Bethany, E-mail: bethany.colling@ccfe.ac.uk [Culham Centre for Fusion Energy, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Department of Engineering, Lancaster University, Lancashire LA1 4YR (United Kingdom); Eade, Tim [Culham Centre for Fusion Energy, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Joyce, Malcolm J. [Department of Engineering, Lancaster University, Lancashire LA1 4YR (United Kingdom); Pampin, Raul; Seyvet, Fabien [Fusion for Energy, Josep Pla 2, Torres Diagonal Litoral B3, 08019 Barcelona (Spain); Turner, Andrew [Culham Centre for Fusion Energy, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Udintsev, Victor [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France)

2016-11-01

Shutdown dose rate calculations have been performed on an integrated ITER C-lite neutronics model with equatorial port 10. A ‘fully shielded’ configuration, optimised for a given set of diagnostic designs (i.e. shielding in all available space within the port plug drawers), results in a shutdown dose rate in the port interspace, from the activation of materials comprising equatorial port 10, in excess of 2000 μSv/h. Achieving dose rates of 100 μSv/h or less, as required in areas where hands-on maintenance can be performed, in the port interspace region will be challenging. A combination of methods will need to be implemented, such as reducing mass and/or the use of reduced activation steel in the port interspace, optimisation of the diagnostic designs and shielding of the port interspace floor. Further analysis is required to test these options and the ongoing design optimisation of the EP10 diagnostic systems.

Surface sediment quality relative to port activities: A contaminant-spectrum assessment.

Science.gov (United States)

Yu, Shen; Hong, Bing; Ma, Jun; Chen, Yongshan; Xi, Xiuping; Gao, Jingbo; Hu, Xiuqin; Xu, Xiangrong; Sun, Yuxin

2017-10-15

Ports are facing increasing environmental concerns with their importance to the global economy. Numerous studies indicated sediment quality deterioration in ports; however, the deterioration is not discriminated for each port activity. This study investigated a spectrum of contaminants (metals and organic pollutants) in surface sediments at 20 sampling points in Port Ningbo, China, one of the top five world ports by volume. The spectrum of contaminants (metals and organic pollutants) was quantified following marine sediment quality guidelines of China and USA and surface sediment quality was assessed according to thresholds of the two guidelines. Coupling a categorical matrix of port activities with the matrix of sedimentary contaminants revealed that contaminants were highly associated with the port operations. Ship repair posed a severe chemical risk to sediment. Operations of crude oil and coal loadings were two top activities related to organic pollutants in sediments while port operations of ore and container loadings discharged metals. Among the 20 sampling points, Cu, Zn, Pb, and DDT and its metabolites were the priority contaminants influencing sediment quality. Overall, surface sediments in Port Ningbo had relatively low environmental risks but ship repair is an environmental concern that must be addressed. This study provides a practical approach for port activity-related quality assessment of surface sediments in ports that could be applicable in many world sites. Copyright © 2017 Elsevier B.V. All rights reserved.

INSTITUTIONAL BARRIERS TO PORT INFRASTRUCTURE AND HARBOR DEVELOPMENT

Directory of Open Access Journals (Sweden)

Roger R. STOUGH

2005-01-01

Full Text Available Ports and their regions have experienced at least a century of crisis from wars (e.g., World War I and II, technological change (e.g., containerization and information and computer technology, political change (e.g., end of the Cold War and liberalization of commerce and trade in countries like China and India and globalization. As such ports have needed to adjust to these conditions to maintain their competitiveness. They have done this by adapting their physical and institutional infrastructures and the adoption of new technologies. In this paper it is argued however that institutional adaptation is the most important way in which ports have changed in pursuit of sustained competitiveness. The paper defines institutions in keeping with the view of the new institutional economists and develops an institutional typology for framing the analyses of four case studies of ports and/or their regions that faced crisis conditions. The case studies include an analysis of the problems and responses made by the ports and then an institutional examination and evaluation of the adjustment process pursued. Conclusions are made as working hypotheses about the process of institutional adjustment to competitiveness crises of ports and their regions and directions for future research are presented.

Compact portable QEPAS multi-gas sensor

Science.gov (United States)

Dong, Lei; Kosterev, Anatoliy A.; Thomazy, David; Tittel, Frank K.

2011-01-01

A quartz-enhanced photoacoustic spectroscopy (QEPAS) based multi-gas sensor was developed to quantify concentrations of carbon monoxide (CO), hydrogen cyanide (HCN), hydrogen chloride (HCl), and carbon dioxide (CO2) in ambient air. The sensor consists of a compact package of dimensions 25cm x 25cm x 10cm and was designed to operate at atmospheric pressure. The HCN, CO2, and HCl measurement channels are based on cw, C-band telecommunication-style packaged, fiber-coupled diode lasers, while the CO channel uses a TO can-packaged Sb diode laser as an excitation source. Moreover, the sensor incorporates rechargeable batteries and can operate on batteries for at least 8 hours. It can also operate autonomously or interact with another device (such as a computer) via a RS232 serial port. Trace gas detection limits of 7.74ppm at 4288.29cm-1 for CO, 450ppb at 6539.11 cm-1 for HCN, 1.48ppm at 5739.26 cm-1 for HCl and 97ppm at 6361.25 cm-1 for CO2 for a 1sec average time, were demonstrated.

Three port converters used as interface in photovoltaic energy systems

Directory of Open Access Journals (Sweden)

Sarab Al-Chlaihawi

2018-04-01

Full Text Available The aim of this paper is to derive and study a full-bridge three-port converter. Based on the standard design of full-bridge converter, we have modeled and derived a three port converter. The three port converter can be used in renewable energy scenarios, such as solar cells or wind turbines connected to the input port. The input can be taken from two-ports simultaneously or from one port at a time. In order to balance the power mismatch between the input port and load port, the batteries are attached to the third port, to ensure there are no discrepancies in the power generated at the input and power demand at the load. In order to ensure isolation and reduced voltage stress on the switches, a high frequency transformer is also used in the design. The overall design contains four switches, and four diodes. MOSFETs are the strongest candidate for the switches owing to their high switching speed, lower losses and high resistance to higher voltage. Moreover, a buck-boost structure is modeled in order to ensure that it can work for a wide variety of different applications by adjusting the duty cycle of the switches properly. To minimize the switching losses in the converter, Zero-Voltage Switching (ZVS is also achievable in the modeled system.

Risk factors for venous port migration in a single institute in Taiwan.

Science.gov (United States)

Fan, Wen-Chieh; Wu, Cheng-Han; Tsai, Ming-Ju; Tsai, Ying-Ming; Chang, Hsu-Liang; Hung, Jen-Yu; Chen, Pei-Huan; Yang, Chih-Jen

2014-01-14

An implantable port device provides an easily accessible central route for long-term chemotherapy. Venous catheter migration is one of the rare complications of venous port implantation. It can lead to side effects such as pain in the neck, shoulder, or ear, venous thrombosis, and even life-threatening neurologic problems. To date, there are few published studies that discuss such complications. This retrospective study of venous port implantation in a single center, a Taiwan hospital, was conducted from January 2011 to March 2013. Venous port migration was recorded along with demographic and characteristics of the patients. Of 298 patients with an implantable import device, venous port migration had occurred in seven, an incidence rate of 2.3%. All seven were male and had received the Bard port Fr 6.6 which had smaller size than TYCO port Fr 7.5 and is made of silicon. Significantly, migration occurred in male patients (P = 0.0006) and in those with lung cancer (P = 0.004). Multivariable logistic regression analysis revealed that lung cancer was a significant risk factor for port migration (odds ratio: 11.59; P = 0.0059). The migration rate of the Bard port Fr 6.6 was 6.7%. The median time between initial venous port implantation and port migration was 35.4 days (range, 7 to 135 days) and 71.4% (5/7) of patients had port migration within 30 days after initial port implantation. Male sex and lung cancer are risk factors for venous port migration. The type of venous port is also an important risk factor.

Test Port for Fiber-Optic-Coupled Laser Altimeter

Science.gov (United States)

Ramos Izquierdo, Luis; Scott, V. Stanley; Rinis, Haris; Cavanaugh, John

2011-01-01

A test port designed as part of a fiber optic coupled laser altimeter receiver optical system allows for the back-illumination of the optical system for alignment verification, as well as illumination of the detector(s) for testing the receiver electronics and signal-processing algorithms. Measuring the optical alignment of a laser altimeter instrument is difficult after the instrument is fully assembled. The addition of a test port in the receiver aft-optics allows for the back-illumination of the receiver system such that its focal setting and boresight alignment can be easily verified. For a multiple-detector receiver system, the addition of the aft-optics test port offers the added advantage of being able to simultaneously test all the detectors with different signals that simulate the expected operational conditions. On a laser altimeter instrument (see figure), the aft-optics couple the light from the receiver telescope to the receiver detector(s). Incorporating a beam splitter in the aft-optics design allows for the addition of a test port to back-illuminate the receiver telescope and/or detectors. The aft-optics layout resembles a T with the detector on one leg, the receiver telescope input port on the second leg, and the test port on the third leg. The use of a custom beam splitter with 99-percent reflection, 1-percent transmission, and a mirrored roof can send the test port light to the receiver telescope leg as well as the detector leg, without unduly sacrificing the signal from the receiver telescope to the detector. The ability to test the receiver system alignment, as well as multiple detectors with different signals without the need to disassemble the instrument or connect and reconnect components, is a great advantage to the aft-optics test port. Another benefit is that the receiver telescope aperture is fully back-illuminated by the test port so the receiver telescope focal setting vs. pressure and or temperature can be accurately measured (as

Economic Contribution of Regional Feeder Ports to The Local Economy In Indonesia

Directory of Open Access Journals (Sweden)

Ibnu Syabri

2017-07-01

Full Text Available Indonesia regional feeder ports’ main function is to serve marine transport activities between regency/city in a province in limited quantities. The intention of the government to make marine transportation as the backbone of national logistic transportation system puts these ports to an important position, as suppliers for the main and/or collector ports and as goods distribution centers for the region from the bigger ports. Not only as a provider of accessibility between regions, regional feeder ports should be seen as an investation to boost regional economy. This study aims to explain the influences of regional feeder ports on regency/city economy, based on the port types: (1 cargo ports, and (2 cargo & passengers ports. Results showed that both types of ports have positive influences on the regency/city economy, although it is not related to region’s economic base sector. Cargo ports which are mainly located on west area of Indonesia, supports the region’s economy more than cargo & passenger ports which are mainly located on the east.

Virtual sensors for active noise control in acoustic-structural coupled enclosures using structural sensing: part II--Optimization of structural sensor placement.

Science.gov (United States)

Halim, Dunant; Cheng, Li; Su, Zhongqing

2011-04-01

The work proposed an optimization approach for structural sensor placement to improve the performance of vibro-acoustic virtual sensor for active noise control applications. The vibro-acoustic virtual sensor was designed to estimate the interior sound pressure of an acoustic-structural coupled enclosure using structural sensors. A spectral-spatial performance metric was proposed, which was used to quantify the averaged structural sensor output energy of a vibro-acoustic system excited by a spatially varying point source. It was shown that (i) the overall virtual sensing error energy was contributed additively by the modal virtual sensing error and the measurement noise energy; (ii) each of the modal virtual sensing error system was contributed by both the modal observability levels for the structural sensing and the target acoustic virtual sensing; and further (iii) the strength of each modal observability level was influenced by the modal coupling and resonance frequencies of the associated uncoupled structural/cavity modes. An optimal design of structural sensor placement was proposed to achieve sufficiently high modal observability levels for certain important panel- and cavity-controlled modes. Numerical analysis on a panel-cavity system demonstrated the importance of structural sensor placement on virtual sensing and active noise control performance, particularly for cavity-controlled modes.

Climate change considerations for the Port Hope area initiative

International Nuclear Information System (INIS)

Kirklady, J.; Morassutti, M.; Tamm, J.; Coutts, P.; Chambers, D.

2006-01-01

The Port Hope Area Initiative (PHAI) is a community-based program intended to develop a safe and long-term (approximately 500 years) solution for the management of historic low-level radioactive waste (LLRW) that has been present in the Port Hope area for many years. The PHAI undertakings involve the construction and management of two Long-Term Low-Level Radioactive Waste Management Facilities (referred to as the LTWMFs) in Port Hope and in Port Granby. These undertakings are currently undergoing detailed examination through the Environmental Screening process under the Canadian Environmental Assessment Act. The purpose of the study described in this paper was to provide information necessary to satisfy the requirements of the Scope of Environmental Assessment for the Port Hope and Port Granby Projects. In particular, the purpose of the study was to satisfy the requirements to evaluate greenhouse gas (GHG) emissions from the proposed PHAI initiatives and to evaluate the potential effect of climate change parameters on the two Projects. The Port Hope and Port Granby Projects will contribute to Ontario's GHG emission inventory due to vehicle exhaust from excavation equipment and haul trucks during the construction phase of the LTWMFs. The construction phase of the Projects is of relatively short duration, and the contribution of GHGs from each Project was determined to be insignificant compared to Ontario's GHG emissions from the Construction and Transportations sectors. The proposed project elements associated with the Port Hope and Port Granby Projects were each evaluated with respect to potential sensitivities to future change in climate parameters. Considering the potential changes to climate, a screening analysis of each element of the LTWMFs was undertaken. Because it is considered likely that the current design level storms will be exceeded within the next 500 years, it was determined that the storm water management system was potentially sensitive to changes

Strategic and Operational Plan Implementation of Seaports (Utilization Jeddah Port

Directory of Open Access Journals (Sweden)

Akram Elentably

2015-12-01

Full Text Available The Port of Jeddah (Port released the initial version of this Strategic Plan in 2006. It was developed by Port staff, along with input, as a five-year rolling plan designed to guide the Port’s future development while keeping in mind the needs of our tenants, local community members and stakeholders, and the nation. This is the second update to the Strategic Plan since its initial release. While the Port’s overarching principles – commitment to environmental stewardship, addressing tenant needs, goods movement, economic development, and security – have remained largely unchanged, it is important for us to adapt our strategies to meet the challenges of an ever changing local and global environment. The Port is among the world’s premier ports and is a critical hub for global trade. This prominence brings with it responsibilities and expectations for the highest possible standards for efficiency, safety and security, and environmental leadership. The Port is the nation’s busiest container port and part of the world’s busiest port complex, handling 3.7 million twenty-foot equivalent units in 2013. Global trade and goods movement is Western kingdom of Saudi Arabia’s strongest industries in terms of jobs and economic activity. The Port of Jeddah powers these industries, handling almost more than a quarter of the cargo that enters the kingdom of Saudi Arabia annually. Through the Port’s activities, a lot of jobs are created in western kingdom of Saudi Arabia and over five hundred thousand nationwide. In order to maintain our position among the world’ the kingdom of Saudi Arabia premier ports, the Port is continually addressing the demands for providing modern and efficient cargo handling terminals as well as transportation and infrastructure projects. Protecting one of the nation’s most vital economic hubs is also an ongoing challenge. Finally, promoting a sustainable “grow green” philosophy and ensuring that we are the leader

Lessons from Hurricane Sandy for port resilience.

Science.gov (United States)

2013-12-01

New York Harbor was directly in the path of the most damaging part of Hurricane Sandy causing significant impact on many of the : facilities of the Port of New York and New Jersey. The U.S. Coast Guard closed the entire Port to all traffic before the...

Working with Nature in Wadden Sea Ports

NARCIS (Netherlands)

Baptist, M.J.; Eekelen, van E.; Dankers, P.J.T.; Grasmeijer, B.; Kessel, van T.; Maren, van D.S.

2017-01-01

Wadden Sea ports are situated at the border of the UNESCO World Heritage site Wadden Sea. Because of the protected status of this area, developing new economic activities is not straightforward. However, maintaining and developing port activities is needed to safeguard the economic viability of the

Maximization of the Supportable Number of Sensors in QoS-Aware Cluster-Based Underwater Acoustic Sensor Networks

Directory of Open Access Journals (Sweden)

Thi-Tham Nguyen

2014-03-01

Full Text Available This paper proposes a practical low-complexity MAC (medium access control scheme for quality of service (QoS-aware and cluster-based underwater acoustic sensor networks (UASN, in which the provision of differentiated QoS is required. In such a network, underwater sensors (U-sensor in a cluster are divided into several classes, each of which has a different QoS requirement. The major problem considered in this paper is the maximization of the number of nodes that a cluster can accommodate while still providing the required QoS for each class in terms of the PDR (packet delivery ratio. In order to address the problem, we first estimate the packet delivery probability (PDP and use it to formulate an optimization problem to determine the optimal value of the maximum packet retransmissions for each QoS class. The custom greedy and interior-point algorithms are used to find the optimal solutions, which are verified by extensive simulations. The simulation results show that, by solving the proposed optimization problem, the supportable number of underwater sensor nodes can be maximized while satisfying the QoS requirements for each class.

Ports and innovation

NARCIS (Netherlands)

Taneja, P.; Vellinga, T.; Van Schuylenburg, M.

2012-01-01

A volatile environment, dynamic markets, and challenges created by new environmental and social consideration demand innovative solutions. Innovation is the implementation of ideas to create value. It promises ports resilience into the future. In this paper we trace some recent successful

A Conceptual Model of Excellent Performance Mode of Port Enterprise Logistics Management

Directory of Open Access Journals (Sweden)

Jiang He

2017-11-01

Full Text Available Port as one of the key hubs of international logistics, which has become the main part and the base of global logistics management. The port enterprises, plays an important role in the global supply chain. However, due to the lack of understanding in port supply chain management, coordination between the port enterprises, the integration of business process is not perfect, the lack of information sharing between various organizations, ports enterprises usually failed to fully play its positive role. Based on this, the paper makes the port enterprises as the research object, and introduces the excellent performance mode into the port enterprises. In order to study the port enterprises how to carry out effective quality management, and formation the coordination and integration of upstream and downstream of enterprises, so as to realize the competitive advantage in port logistics.

Single port Billroth I gastrectomy

Directory of Open Access Journals (Sweden)

Jeremy R Huddy

2013-01-01

Full Text Available Introduction: Experience has allowed increasingly complex procedures to be undertaken by single port surgery. We describe a technique for single port Billroth I gastrectomy with a hand-sewn intracorporeal anastomosis in the resection of a benign tumour diagnosed incidentally on a background of cholelithiasis. Materials and Methods: Single port Billroth I gastrectomy and cholecystectomy was performed using a transumbilical quadport. Flexible tipped camera and straight conventional instruments were used throughout the procedure. The stomach was mobilised including a limited lymph node dissection and resection margins in the proximal antrum and duodenum were divided with a flexible tipped laparoscopic stapler. The lesser curve was reconstructed and an intracorporal hand sewn two layer end-to-end anastomosis was performed using unidirectional barbed sutures. Intraoperative endoscopy confirmed the anastomosis to be patent without leak. Results: Enteral feed was started on the day of surgery, increasing to a full diet by day 6. Analgesic requirements were a patient-controlled analgesia morphine pump for 4 postoperative days and paracetamol for 6 days. There were no postoperative complications and the patient was discharged on the eighth day. Histology confirmed gastric submucosal lipoma. Discussion: As technology improves more complex procedures are possible by single port laparoscopic surgery. In this case, flexible tipped cameras and unidirectional barbed sutures have facilitated an intracorporal hand-sewn two layer end-to-end anastomosis. Experience will allow such techniques to become mainstream.

The effect of monsoon variability on fish landing in the Sadeng Fishing Port of Yogyakarta, Indonesia

Science.gov (United States)

Subarna, D.

2018-03-01

The volume of landing fish of the Sadeng Fishing Port within certain months showed an increase from year to year, especially during June, July and August (JJA). While in other months the fish production was low. The purpose of this research was to understand the influence of monsoon variability on fish landing in the Sadeng Fishing Port. Data were analyzed descriptively as spatial and temporal catch. Data were namely catch fish production collected from fishing port, while satellite and HYCOM model during 2011–2012 period were selected. The wind data, sea surface temperature (SST) and chlorophyll-a were analyzed from ASCAT and MODIS sensors during the Southeast Monsoon. The result showed the wind from the southeasterly provide wind stress at sea level and caused Ekman Transport to move away water mass from the sea shore. The lost water mass in the ocean surface was replaced by cold water from deeper layer which was rich in nutrients. The distribution of chlorophyll-a during the Southeast Monsoon was relatively higher in the southern coast of Java than during the Northwest monsoon. The SST showed approximately 25.3 °C. The abundance of nutrients indicated by the distribution of chlorophyll-a around the coast during the Southeast Monsoon, will enhance the arrival of larger fish. Thus, it can be understood that during June, July, and August the catch production is higher than the other months.

Color in interior spaces

OpenAIRE

Demirörs, Müge Bozbeyli

1992-01-01

Ankara : The Department of Interior Architecture and Environmental Design and the Institute of Fine Arts of Bilkent University, 1992. Thesis (Master's) -- -Bilkent University, 1992. Includes bibliographical references leaves 95-99. Color can be approached from different perspectives and disciplines such as, biology, theory, technology, and psychology. This thesis discusses color, from the stand point of interior spaces, which to some extent involves most of these discipli...

Development of the alternate entry port for the ATF

International Nuclear Information System (INIS)

Parsa, Z.

1993-05-01

We discussed a second entry port for the Accelerator Test Facility (ATF) injection system at Brookhaven National Laboratory, which consists of a photocathode rf gun and a straight - ahead beamline directly into the 50 MeV linac. The proposed second entry port should improve the beam quality and lower the emittance needed for FEL (Free Electron Laser), and laser - acceleration experiments. A discussion on the laser driven high brightness photoelectrons through the primary entry port (a low energy 180 degrees achromatic double bend transport line) now in operation, and a beam analysis for the proposed secondary port is also given

Integration of Land and Sea in a Port Area: A Case Study of the Port of Koper

Science.gov (United States)

Ažman Momirski, Lucija

2017-10-01

The spatial plan for a port based on land reclamation, existing land, or a combination of both should be designed in line with both reliable data for the existing situation and precise goals based on a well-founded vision by the port authority. In ports, human activities are concentrated in the limited space of the coastal belt, where they threaten the vulnerable equilibrium of the environment. Integrated multifunctional planning of ports is necessary for the sustainability of such plans. In this process, the relation between the environment and the economy is often neglected because the ecosystem—the totality of living organisms—which is fully dependent on biological, chemical, and physical factors, prevails. This method, also called building with nature, is the basis for integrated coastal zone development and management. It emphasizes the flexible integration of land and sea, which respects and uses forces and materials present in nature, and which is an essential interaction between man and environment. Strict ecological planning conditions and the public interest obliged the Port of Koper to modify its urban planning strategies and redefine its relationship with all bordering areas. The extension of two piers and construction of a third one was the result of functional factors, infrastructure connections, technical possibilities, and environmental requirements. Solutions that were relevant for distributing cargo on the docks had to adjust to the width of the basins for manoeuvring ships. Various types of construction restrict water flow under piers, thereby accelerating biomass degradation. Environmental aspects created conditions and requirements for pier construction.

Discovering the interior of black holes

Science.gov (United States)

Brustein, Ram; Medved, A. J. M.; Yagi, K.

2017-12-01

The detection of gravitational waves (GWs) from black hole (BH) mergers provides an inroad toward probing the interior of astrophysical BHs. The general-relativistic description of the BH interior is that of empty spacetime with a (possibly) singular core. Recently, however, the hypothesis that the BH interior does not exist has been gaining traction, as it provides a means for resolving the BH information-loss problem. Here, we propose a simple method for answering the following question: Does the BH interior exist and, if so, does it contain some distribution of matter or is it mostly empty? Our proposal is premised on the idea that, similar to the case of relativistic, ultracompact stars, any BH-like object whose interior has some matter distribution should support fluid modes in addition to the conventional spacetime modes. In particular, the Coriolis-induced Rossby (r-) modes, whose spectrum is mostly insensitive to the composition of the interior matter, should be a universal feature of such BH-like objects. In fact, the frequency and damping time of these modes are determined by only the object's mass and speed of rotation. The r-modes oscillate at a lower frequency, decay at a slower rate, and produce weaker GWs than do the spacetime modes. Hence, they imprint a model-insensitive signature of a nonempty interior in the GW spectrum resulting from a BH merger. We find that future GW detectors, such as Advanced LIGO with its design sensitivity, have the potential of detecting such r-modes if the amount of GWs leaking out quantum mechanically from the interior of a BH-like object is sufficiently large.

Dry Port Location Problem: A Hybrid Multi-Criteria Approach

Directory of Open Access Journals (Sweden)

BENTALEB Fatimazahra

2016-03-01

Full Text Available Choosing a location for a dry port is a problem which becomes more essential and crucial. This study deals with the problem of locating dry ports. On this matter, a model combining multi-criteria (MACBETH and mono-criteria (BARYCENTER methods to find a solution to dry port location problem has been proposed. In the first phase, a systematic literature review was carried out on dry port location problem and then a methodological classification was presented for this research. In the second phase, a hybrid multi-criteria approach was developed in order to determine the best dry port location taking different criteria into account. A Computational practice and a qualitative analysis from a case study in the Moroccan context have been provided. The results show that the optimal location is very convenient with the geographical region and the government policies.

Interface Circuit For Printer Port

Science.gov (United States)

Tucker, Jerry H.; Yadlowsky, Ann B.

1991-01-01

Electronic circuit, called printer-port interface circuit (PPI) developed to overcome certain disadvantages of previous methods for connecting IBM PC or PC-compatible computer to other equipment. Has both reading and writing modes of operation. Very simple, requiring only six integrated circuits. Provides for moderately fast rates of transfer of data and uses existing unmodified circuit card in IBM PC. When used with appropriate software, circuit converts printer port on IBM PC, XT, AT, or compatible personal computer to general purpose, 8-bit-data, 16-bit address bus that connects to multitude of devices.

Port-site metastases following robot-assisted laparoscopic surgery for gynecological malignancies.

Science.gov (United States)

Lönnerfors, Celine; Bossmar, Thomas; Persson, Jan

2013-12-01

To evaluate the incidence and possible predictors associated with port-site metastases following robotic surgery. Prospective study. University Hospital. Women with gynecological cancer. The occurrence of port-site metastases in the first 475 women undergoing robotic surgery for gynecological cancer was reviewed. Rate of port-site metastases. A port-site metastasis was detected in nine of 475 women (1.9%). Eight women had either an unexpected locally advanced disease or lymph-node metastases at the time of surgery. All nine women received postoperative adjuvant therapy. Women with ≥ stage III endometrial cancer and women with node positive cervical cancer had a significantly higher risk of developing a port-site metastasis, as did women with high-risk histology endometrial cancer. Port-site metastases were four times more likely to occur in a specimen-retrieval port. One (0.2%) isolated port-site metastasis was detected. The median time to occurrence of a port-site metastasis was 6 months (range 2-19 months). Six of the nine women (67%) have died and their median time of survival from recurrence was 4 months (range 2-16 months). In women with gynecological cancer, the incidence of port-site metastases following robotic surgery was 1.9%. High-risk histology and/or advanced stage of disease at surgery seem to be contributing factors. © 2013 Nordic Federation of Societies of Obstetrics and Gynecology.

Scout-view assisted interior micro-CT

International Nuclear Information System (INIS)

Sharma, Kriti Sen; Narayanan, Shree; Agah, Masoud; Holzner, Christian; Vasilescu, Dragoş M; Jin, Xin; Hoffman, Eric A; Yu, Hengyong; Wang, Ge

2013-01-01

Micro computed tomography (micro-CT) is a widely-used imaging technique. A challenge of micro-CT is to quantitatively reconstruct a sample larger than the field-of-view (FOV) of the detector. This scenario is characterized by truncated projections and associated image artifacts. However, for such truncated scans, a low resolution scout scan with an increased FOV is frequently acquired so as to position the sample properly. This study shows that the otherwise discarded scout scans can provide sufficient additional information to uniquely and stably reconstruct the interior region of interest. Two interior reconstruction methods are designed to utilize the multi-resolution data without significant computational overhead. While most previous studies used numerically truncated global projections as interior data, this study uses truly hybrid scans where global and interior scans were carried out at different resolutions. Additionally, owing to the lack of standard interior micro-CT phantoms, we designed and fabricated novel interior micro-CT phantoms for this study to provide means of validation for our algorithms. Finally, two characteristic samples from separate studies were scanned to show the effect of our reconstructions. The presented methods show significant improvements over existing reconstruction algorithms. (paper)

Performance Effects of the Corporatisation of Port of Rotterdam Authority

NARCIS (Netherlands)

P.W. de Langen (Peter); C. Heij (Christiaan)

2013-01-01

textabstractPort of Rotterdam Authority is a publicly owned but corporatized port development company. In 2004, this organisation was transformed from a municipal department to an independently operating company. The corporatisation intended to improve the overall performance of the port of

The Port Hope area initiative from municipal perspective

International Nuclear Information System (INIS)

Austin, R.

2006-01-01

'Full text:' This paper explores the Municipal perspective of the Port Hope Area Initiative (PHAI). The PHAI is unique in that it emerged from proposals to the Federal Government and subsequently a tri-partite agreement between the Federal Government and the Municipalities of Port Hope and Clarington for the cleanup and management of historic low-level radioactive wastes in long-term waste management facilities in their Municipalities. A key feature of the Port Hope Project is the remediation of many major and small scale sites in the urban area. As part of this Legal Agreement, each Municipality is required to give consent at key milestones for the project to proceed to the next stage. In addition, the Municipality also has veto authority if the preferred option is changed by the federal government during its final review. The Agreement also ensures that the Municipalities have the resources to conduct an independent assessment of the work completed by the federal proponent and to advise the Municipality on related matters. While this Legal Agreement provides the Municipalities with influence over the outcome of the EA and the project description, especially when compared with the typical role of municipalities in other Federal EAs, there are many challenges that Port Hope faces as partner in this process. These include: Balancing Port Hope's interests with those of the Federal Government; Reaching agreement on how clean the remediation sites should be; Considering the interests of future generations while meeting the needs of existing residents; Ensuring that the Project will have a positive legacy for Port Hope; Ensuring that institutional controls are in place and that Port Hope has a partnership role in monitoring the Project performance during the Construction Phase and the long term Maintenance and Monitoring Phase. In this context, this paper presents the unique aspects of the Municipal involvement in the process to finally achieve a safe, environmentally

Port interface requirements

International Nuclear Information System (INIS)

O'Neil, R.

1978-01-01

In a land-based reactor programme the Administration are usually confronted with a specific design in a particular environment. Safety and Reliability criteria necessary to the designer can be specified on the basis of acceptable risk to the population. However for the successful implementation of a nuclear ship programme on a broad commercial basis it is necessary to have agreed standards of risks from ships yet to be designed and agreed standards of acceptable risks to the population at likely ports of call yet to be specified, consulted, or agreed. At first sight it would seem that this double uncertainty must either lead to unnecessarily high safety standards for the ship or unacceptably conservative standards for berth selection. The paper discusses the problem and proposes a possible solution based on the concept of a 'Standard Port' and a 'Standard Ship' and indicates the level of risk implied by such a concept

Visual Support for Porting Large Code Bases

NARCIS (Netherlands)

Broeksema, Bertjan; Telea, Alexandru

2011-01-01

We present a tool that helps C/C++ developers to estimate the effort and automate software porting. Our tool supports project leaders in planning a porting project by showing where a project must be changed, how many changes are needed, what kinds of changes are needed, and how these interact with

Two-port Laparoscopic-assisted Appendicectomy Under Local ...

African Journals Online (AJOL)

Journal of Surgical Technique and Case Report | Jul-Dec 2011 | Vol-3 | Issue-2. 84. Two-port Laparoscopic-assisted ... appendicectomy (LAA) using the two-port technique under local anesthesia in adults. As a pilot study we .... of failure are the reasons for avoidance of using local anesthesia for surgical procedures.

Colour terms in the interior design process

OpenAIRE

Attiah, DY; Cheung, TLV; Westland, S; Bromilow, D

2015-01-01

Colour is a very important topic that interior designers need to consider. Considerable research has been conducted in the area of colour application in interior design; in this study we are concerned with colour terms in interior design, mainly the terms designers use and know about. Fifteen interior designers with varied professional backgrounds, but based in the Middle East (Saudi Arabia, Dubai, Bahrain, Lebanon, Egypt, and Turkey), were interviewed. Previously we reported that fourteen ou...

Use of CFD in development of intake ports for diesel engines

International Nuclear Information System (INIS)

Alcenius, T.

2002-01-01

The design of intake ports for diesel engines is difficult due to the many competing requirements of the cylinder head design. When the concept design is completed, the typical course for verification and optimization of the port is through steady state flow testing. In the past, optimization of the port was considered a 'black art' as the final shape of the port and its performance was tied directly to the experience of the port development engineer. As CFD has been increasingly used to analyze various aspects of engine performance, an obvious area to explore is its use to predict steady state port flow performance prior to fabrication of any test hardware. A study was carried out to evaluate the usefulness of CFD in predicting steady state flow bench results and to provide insight into the fluid mechanics of the port flow to assist in the flow bench development. Port flow testing was carried out on a baseline diesel engine port for a range of valve lifts from zero to just above the maximum valve lift. This experimental test data was used to calculate flow coefficients and swirl ratios (an indicator of mean air motion in the cylinder). Subsequently, CFD models were generated that replicated the flow bench set-up. Three valve lifts across the valve lift range were chosen for the comparison. Results of the analysis were used to calculate flow coefficients and swirl ratios. Computed results were then compared to the experiments to determine their accuracy and a detailed review of the CFD results was conducted to understand the flow in the port. Modifications were made to the port from recommendations made based on the CFD results. The ports were then retested to determine the effectiveness of the recommendations. Finally, the results are discussed as to their meaning and usefulness for design programs. (author)

Spatial Determinants of Import Traffic Distribution At Port Harcourt (Nigeria

Directory of Open Access Journals (Sweden)

Soddy I. Inyang

2013-07-01

Full Text Available This paper highlights the result of a study carried out to examine the Geographic determinants of import traffic distribution at the Port Harcourt Port. A substantial aspect of the study involved building a regression model to estimate import distribution from the Port. The import function was specified in log-linear form. The adequacy of the model was then tested; this, involved statistical experiments to obtain the R-squared, as well as t and f values. Further test on the adequacy of the nwdel was conducted through diagnostic exercises designed to check for inulticollinedrity and heteroscedasticity, in the data used. Results obtained show that road distance and manufacturing industries are significant Geographic determinants of import Cargo distribution at the study Port. It is therefore important to lake the two variables into account in any policy or planning exercise at Port Harcourt Port.

The role of sea ports in end-to-end maritime transport chain emissions

International Nuclear Information System (INIS)

Gibbs, David; Rigot-Muller, Patrick; Mangan, John; Lalwani, Chandra

2014-01-01

This paper's purpose is to investigate the role of sea ports in helping to mitigate the GHG emissions associated with the end-to-end maritime transport chain. The analysis is primarily focused on the UK, but is international in application. The paper is based on both the analysis of secondary data and information on actions taken by ports to reduce their emissions, with the latter data collected for the main UK ports via their published reports and/or via interviews. Only a small number of ports (representing 32% of UK port activity) actually measure and report their carbon emissions in the UK context. The emissions generated by ships calling at these ports are analysed using a method based on Department for Transport Maritime Statistics Data. In addition, a case example (Felixstowe) of emissions associated with HGV movements to and from ports is presented, and data on vessel emissions at berth are also considered. Our analyses indicate that emissions generated by ships during their voyages between ports are of a far greater magnitude than those generated by the port activities. Thus while reducing the ports' own emissions is worthwhile, the results suggest that ports might have more impact through focusing their efforts on reducing shipping emissions. - Highlights: • Investigates role of ports in mitigating GHG emissions in the end-to-end maritime transport chain. • Emissions generated both by ports and by ships calling at ports are analysed. • Shipping's emissions are far greater than those generated by port activities. • Ports may have more impact through focusing efforts on reducing shipping's emissions. • Options for ports to support and drive change in the maritime sector also considered

Pollution prevention at ports: clearing the air

International Nuclear Information System (INIS)

Bailey, Diane; Solomon, Gina

2004-01-01

Seaports are major hubs of economic activity and of environmental pollution in coastal urban areas. Due to increasing global trade, transport of goods through ports has been steadily increasing and will likely continue to increase in the future. Evaluating air pollution impacts of ports requires consideration of numerous sources, including marine vessels, trucks, locomotives, and off-road equipment used for moving cargo. The air quality impacts of ports are significant, with particularly large emissions of diesel exhaust, particulate matter, and nitrogen oxides. The health effects of these air pollutants to residents of local communities include asthma, other respiratory diseases, cardiovascular disease, lung cancer, and premature mortality. In children, there are links with asthma, bronchitis, missed school days, and emergency room visits. The significance of these environmental health impacts requires aggressive efforts to mitigate the problem. Approaches to mitigation encompass a range of possibilities from currently available, low-cost approaches, to more significant investments for cleaner air. Examples of the former include restrictions on truck idling and the use of low-sulfur diesel fuel; the latter includes shore-side power for docked ships, and alternative fuels. A precautionary approach to port-related air pollution would encourage local production of goods in order to reduce marine traffic, greener design for new terminals, and state-of-the art approaches to emissions-control that have been successfully demonstrated at ports throughout the world

CEA engineering studies and integration of the ITER diagnostic port plugs

International Nuclear Information System (INIS)

Doceul, L.; Walker, C.; Ingesson, C.; Ciattaglia, E.; Chappuis, P.; Portafaix, C.; Salasca, S.; Thomas, E.; Tremblay, G.; Bruyere, C.

2007-01-01

Most of the ITER diagnostic system is integrated in port plugs, which are water cooled stainless steel structures inserted into the vacuum-vessel ports. The port plug must perform basic functions such as providing neutron and gamma shielding, supporting the first wall armour and shielding blanket material, closing the vacuum vessel ports, while supporting the diagnostic equipment. CEA has contributed to the engineering activities on the port plugs and has more particularly focused on the design and diagnostic integration in the representative equatorial port plug Eq no. 01. The specific CEA contributions have been the engineering, structural and thermal analysis. These detailed analyses have highlighted some design issues which were worked out through different solutions. This paper contains a description of the engineering activities performed such as: the conceptual design of the Eq no. 01 port plug, the static mechanical calculations, the dynamic calculation to estimate the dynamic amplification factor due to the resonance phenomenon, the thermal assessment under the neutronic load and the seismic response of the port plug inside the vacuum vessel

CEA engineering studies and integration of the ITER diagnostic port plugs

Energy Technology Data Exchange (ETDEWEB)

Doceul, L. [Association Euratom-CEA sur la Fusion Controlee, Centre d' Etudes de Cadarache, F-13108 Saint-Paul-Lez-Durance Cedex (France)], E-mail: louis.doceul@cea.fr; Walker, C. [ITER International Team, Boltzmannstr. 2, D-85748 Garching bei Muenchen (Germany); Ingesson, C.; Ciattaglia, E. [EFDA CSU - Garching, Boltzmannstr. 2, D-85748 Garching bei Muenchen (Germany); Chappuis, P.; Portafaix, C.; Salasca, S.; Thomas, E.; Tremblay, G.; Bruyere, C. [Association Euratom-CEA sur la Fusion Controlee, Centre d' Etudes de Cadarache, F-13108 Saint-Paul-Lez-Durance Cedex (France)

2007-10-15

Most of the ITER diagnostic system is integrated in port plugs, which are water cooled stainless steel structures inserted into the vacuum-vessel ports. The port plug must perform basic functions such as providing neutron and gamma shielding, supporting the first wall armour and shielding blanket material, closing the vacuum vessel ports, while supporting the diagnostic equipment. CEA has contributed to the engineering activities on the port plugs and has more particularly focused on the design and diagnostic integration in the representative equatorial port plug Eq no. 01. The specific CEA contributions have been the engineering, structural and thermal analysis. These detailed analyses have highlighted some design issues which were worked out through different solutions. This paper contains a description of the engineering activities performed such as: the conceptual design of the Eq no. 01 port plug, the static mechanical calculations, the dynamic calculation to estimate the dynamic amplification factor due to the resonance phenomenon, the thermal assessment under the neutronic load and the seismic response of the port plug inside the vacuum vessel.

Engineering activities on the ITER representative diagnostic equatorial port plug

International Nuclear Information System (INIS)

Meunier, L.; Doceul, L.; Salasca, S.; Martins, J.-P.; Jullien, F.; Dechelle, Christian; Bidaud, Pierre; Pilard, Vincent; Terra, Alexis; Ogea, Mathieu; Ciattaglia, Emanuela; Walker, Christopher

2009-01-01

Most of ITER diagnostic systems are integrated in port plugs, which are water cooled stainless steel structures inserted into the vacuum vessel ports. The port plug must provide basic functions such as neutron and gamma shielding, supporting the first wall armour (BSM), closing the vacuum vessel ports, while supporting the diagnostic equipments. ITER diagnostic port plug must resist a severe environment like high temperature due to neutron interaction with the structures and high electromechanical loading during disruptions events. CEA has contributed to the design and integration tasks in the frame of the representative equatorial port plug EQ no. 01, in particular on the engineering, structural and thermal finite element analysis. These detailed analyses have highlighted some design issues which were worked out through different solutions. This paper contains a description of the engineering activities performed such as: -The static mechanical calculations of the top plate closure system under disruption load. -The static mechanical calculations of the BSM attachment to the port plug. These two first studies led to design changes proposals which significantly improved the behaviour of the structures but also showed that the safety margin with respect to design limits is quite low. -The design of a Diagnostic Shield Module (DSM) integrated inside the port plug and a proposition of attachment scheme, with respect to disruption loads. The manufacturing of the DSM has been taken into account, as well as diagnostic integration inside the structure and maintenance aspects. -The thermal assessment of the port plug under neutronic load during normal operation, with the optimization of the cooling system. The maximum temperature calculated in normal operation has been reduced from 900 deg. C to less than 400 deg. C in the front plate; and the cooling arrangement at the back of the port plug has been simplified without important temperature increase.

Engineering activities on the ITER representative diagnostic equatorial port plug

Energy Technology Data Exchange (ETDEWEB)

Meunier, L. [Association Euratom CEA, CEA/DSM/IRFM (France)], E-mail: lmeunier@cea.fr; Doceul, L.; Salasca, S.; Martins, J.-P.; Jullien, F.; Dechelle, Christian; Bidaud, Pierre; Pilard, Vincent; Terra, Alexis; Ogea, Mathieu [Association Euratom CEA, CEA/DSM/IRFM (France); Ciattaglia, Emanuela [EFDA CSU, Garching (Germany); Walker, Christopher [ITER International Organisation (France)

2009-06-15

Most of ITER diagnostic systems are integrated in port plugs, which are water cooled stainless steel structures inserted into the vacuum vessel ports. The port plug must provide basic functions such as neutron and gamma shielding, supporting the first wall armour (BSM), closing the vacuum vessel ports, while supporting the diagnostic equipments. ITER diagnostic port plug must resist a severe environment like high temperature due to neutron interaction with the structures and high electromechanical loading during disruptions events. CEA has contributed to the design and integration tasks in the frame of the representative equatorial port plug EQ no. 01, in particular on the engineering, structural and thermal finite element analysis. These detailed analyses have highlighted some design issues which were worked out through different solutions. This paper contains a description of the engineering activities performed such as: -The static mechanical calculations of the top plate closure system under disruption load. -The static mechanical calculations of the BSM attachment to the port plug. These two first studies led to design changes proposals which significantly improved the behaviour of the structures but also showed that the safety margin with respect to design limits is quite low. -The design of a Diagnostic Shield Module (DSM) integrated inside the port plug and a proposition of attachment scheme, with respect to disruption loads. The manufacturing of the DSM has been taken into account, as well as diagnostic integration inside the structure and maintenance aspects. -The thermal assessment of the port plug under neutronic load during normal operation, with the optimization of the cooling system. The maximum temperature calculated in normal operation has been reduced from 900 deg. C to less than 400 deg. C in the front plate; and the cooling arrangement at the back of the port plug has been simplified without important temperature increase.

Image-guided placement of port catheters: is there an increased risk of infection if the port is immediately accessed and used?

Science.gov (United States)

Salazar, Gloria; Yeddula, Kalpana; Wicky, Stephan; Oklu, Ramhi; Ganguli, Suvranu; Waltman, Arthur C; Walker, Thomas G; Kalva, Sanjeeva P

2013-01-01

To compare complication rates in patients who have port-a-catheters inserted and left accessed for immediate use and those who have ports inserted but not accessed. In this retrospective, IRB-approved study, medical records of patients who received a port catheter between 9/2009 and 2/2010 were reviewed. The data collected included patient demographics, diagnosis, procedure and complications. The patients were categorized into two groups: accessed (patients in whom the port was accessed with a Huber needle for immediate intravenous use and the patient left the procedure area with needle indwelling) and control (patients in whom the ports were not accessed). Complications were classified according to Society of Interventional Radiology guidelines. Results are given as mean ±SD. Statistical analysis was performed with student t test and statistical significance was considered at Pports were placed in 465 patients (Men: 206); 10.7% in the accessed group (n=50, age: 60±13.9) and 89.3% in the control group (n=417, age: 59±13.5). There were no statistically significant differences in patient demographics between the groups. The overall complication rate was 0.6% (n=3). Two complications (hematoma causing skin necrosis and thrombosis of the port) occurred in the control group and one (infection) in the accessed group. Infection rates after procedures were 2% (1/50) in the accessed group and 0% (0/417) in the control group. There was no statistically significant difference in overall complication (P=.1) and infection (P=.1) rates among the groups. Leaving the port accessed immediately after placement does not increase the risk of infection or other complications.

A Comparative Study of Acute and Chronic Pain between Single Port and Triple Port Video-assisted Thoracic Surgery for Lung Cancer

Directory of Open Access Journals (Sweden)

Caiwei LI

2018-04-01

Full Text Available Background and objective Through the comparative analysis of the acute and chronic pain postoperative between the single port and triple port video-assisted thoracic surgery to seek the better method which can reduce the incidence of acute and chronic pain in patients with lung cancer. Methods Data of 232 patients who underwent single port -VATS (n=131 or triple port VATS (n=101 for non-small cell lung cancer (NSCLC on January 1, 2016 to June 30, 2017 in our hospital were analyzed. The clinical and operative data were assessed, numeric rating scale (NRS was used to evaluate the mean pain score on the 1th, 2th, 3th, 7th, 14th days, 3th months and 6th months postoperative. Results Both groups were similar in clinical characteristics, there were no perioperative death in two groups. In the 1th, 2th, 7th, 14th days and 3th, 6th months postoperative, the NRS score of the single port group was superior, and the difference was significant compared with the triple port (P0.05. Univariate and multivariate analysis of the occurrence on the chronic pain showed that the operation time, surgical procedure and the 14th NRS score were risk factors for chronic pain (P<0.05. Conclusion The single port thoracoscopic surgery has an advantage in the incidence of acute and chronic pain in patients with non-small cell lung cancer. Shorter operative time can reduce the occurrence of chronic pain. The 14th day NRS score is a risk factor for chronic pain postoperative.

Clinical predictors of port infections within the first 30 days of placement.

Science.gov (United States)

Bamba, Ravinder; Lorenz, Jonathan M; Lale, Allison J; Funaki, Brian S; Zangan, Steven M

2014-03-01

To identify risk factors for port infections within 30 days of placement. A retrospective chart review of port placements from 2002-2009 was conducted. Patients who had port removals secondary to infection within the first 30 days of placement were included. This group of patients was compared with a control group of patients with ports with no evidence of infection. For every one patient with a port infection, two control subjects were chosen of the same gender and new port placement during the same month as the corresponding patient with an infected port. From 2002-2009, 4,404 ports were placed. Of the 4,404 patients, 33 (0.7%) were found to have a port infection within 30 days of placement. Compared with the control group, the early infection group had a higher prevalence of leukopenia (21.2% vs 6.1%, P = .039) and thrombocytopenia (33% vs 12%, P = .0158). There was also a higher prevalence of an inpatient hospital stay during port placement and high international normalized ratio in the early infection group. Low preoperative white blood cell and platelet counts were risk factors for early infection. Abnormal coagulation profiles and inpatient access of ports after placement could be additional risk factors. Copyright © 2014 SIR. Published by Elsevier Inc. All rights reserved.

Strategic port development

DEFF Research Database (Denmark)

Olesen, Peter Bjerg; Dukovska-Popovska, Iskra; Steger-Jensen, Kenn

2012-01-01

This paper proposes a framework for strategic development of a port’s collaboration with its hinterland. The framework is based on literature relevant to port development and undertakes market perspective by considering import/export data relevant for the region of interest. The series of steps...

Port-wine stain

Science.gov (United States)

... About MedlinePlus Show Search Search MedlinePlus GO GO About MedlinePlus Site Map FAQs Customer Support Health Topics Drugs & Supplements Videos & Tools Español You Are Here: Home → Medical Encyclopedia → Port-wine stain URL of this page: //medlineplus.gov/ency/ ...

Port wine stain on a child's face (image)

Science.gov (United States)

Port wine stains are always present at birth. In an infant, they are flat, pink, vascular lesions. Common locations ... may be present anywhere on the body. Port wine stains may appear in association with other syndromes.

The state-of-the-art port of entry workshop

Energy Technology Data Exchange (ETDEWEB)

Godfrey, B.

1995-05-01

The increased demand for freight movements through international ports of entry and the signing of the North American Free Trade Agreement (NAFTA) have increased freight traffic at border ports of entry. The State-of-the-Art Port of Entry Workshop initiated a dialogue among technologists and stakeholders to explore the potential uses of technology at border crossings and to set development priorities. International ports of entry are both information and labor intensive, and there are many promising technologies that could be used to provide timely information and optimize inspection resources. Participants universally held that integration of technologies and operations is critical to improving port services. A series of Next Steps was developed to address stakeholder issues and national priorities, such as the National Transportation Policy and National Drug Policy. This report documents the views of the various stakeholders and technologists present at the workshop and outlines future directions of study.

Structural Analysis for an Upper Port of the ITER Vacuum Vessel

International Nuclear Information System (INIS)

Yun-Seok Hong; Kwon, T. K.; Ahn, H. J.; Kim, Y.K.; Lee, C.D.

2006-01-01

The ITER vacuum vessel (VV) has numerous openings for the port structures including upper, equatorial, and lower ports used for equipment installation, utility feed through, vacuum pumping, and access into the vessel for maintenance. Every upper port, slanted upward slightly, has a trapezoidal/rectangular cross-section and consists of a port stub, a stub extension and a port extension with a connecting duct. To investigate the structural integrity and to increase the structural reliability of the VV and ports, the structural analyses of the upper port structure have been performed. The global structural analysis of the upper port with the in-port components has been carried out. The local analyses of a tangential key, an upper port flange, a connecting duct and a sealing unit have been performed. The design loads are dead weight, normal and abnormal pressure load, electromagnetic load, and seismic load in consideration of the dynamic amplification factors. The stress analyses were performed in a nonlinear elastic approach taking into account the contact surface between port extension flange and port plug flange. Two advanced designs from the ITER international team have been reviewed. To verify the strength of the reinforcing ribs for the connecting duct and of the fastening/sealing units, the local analyses utilizing the sub-modeling technique have been performed. The ASME code and the ITER design criteria were applied for the evaluation of the structural analysis results from the global and local analyses. The clearance between a port and a plug to accommodate the plug deformation has been assessed. The upper port flange based on the original design could withstand design loads, but there could be a gap on the flange surface under the design condition. The modified flange design, which is under the bolt friction only without tangential key was proposed. The deflection of the plug for an advanced design with a removable flange is higher than that for the original

Measure Guideline: Summary of Interior Ducts in New Construction, Including an Efficient, Affordable Method to Install Fur-Down Interior Ducts

Energy Technology Data Exchange (ETDEWEB)

Beal, D.; McIlvaine , J.; Fonorow, K.; Martin, E.

2011-11-01

This document illustrates guidelines for the efficient installation of interior duct systems in new housing, including the fur-up chase method, the fur-down chase method, and interior ducts positioned in sealed attics or sealed crawl spaces. This document illustrates guidelines for the efficient installation of interior duct systems in new housing. Interior ducts result from bringing the duct work inside a home's thermal and air barrier. Architects, designers, builders, and new home buyers should thoroughly investigate any opportunity for energy savings that is as easy to implement during construction, such as the opportunity to construct interior duct work. In addition to enhanced energy efficiency, interior ductwork results in other important advantages, such as improved indoor air quality, increased system durability and increased homeowner comfort. While the advantages of well-designed and constructed interior duct systems are recognized, the implementation of this approach has not gained a significant market acceptance. This guideline describes a variety of methods to create interior ducts including the fur-up chase method, the fur-down chase method, and interior ducts positioned in sealed attics or sealed crawl spaces. As communication of the intent of an interior duct system, and collaboration on its construction are paramount to success, this guideline details the critical design, planning, construction, inspection, and verification steps that must be taken. Involved in this process are individuals from the design team; sales/marketing team; and mechanical, insulation, plumbing, electrical, framing, drywall and solar contractors.

ECSPECT prospective multicentre registry for single-port laparoscopic colorectal procedures

DEFF Research Database (Denmark)

Weiss, Helmut; Zorron, R; Vestweber, K-H

2017-01-01

BACKGROUND: The international multicentre registry ECSPECT (European Consensus of Single Port Expertise in Colorectal Treatment) was established to evaluate the general feasibility and safety of single-port colorectal surgery with regard to preoperative risk assessment. METHODS: Consecutive...... patients undergoing single-port colorectal surgery were enrolled from 11 European centres between March 2010 and March 2014. Data were analysed to assess patient-, technique- and procedure-dependent parameters. A validated sex-adjusted risk chart was developed for prediction of single-port colorectal...

Current epidemiology of hypertension in Port Harcourt metropolis ...

African Journals Online (AJOL)

Current epidemiology of hypertension in Port Harcourt metropolis, Rivers State ... the University of Port Harcourt Teaching Hospital formed the cohort for this study. ... is high and only a small fraction of hypertensives are aware of their condition.

Characterization of the near-source population around five candidate ports.

Science.gov (United States)

Our results indicate that environmental justice issues continue to be a concern in port areas. Within the 10 km domain of the port boundary, the Ports of Houston and Virginia had the greatest disparities in median income combined with the greater percentages of Blacks (in Virgini...

FHWA operations support : port peak pricing program evaluation

Science.gov (United States)

2009-01-01

This report evaluates the applicability, Federal policy implications, and possible public and private sector roles related to peak pricing strategies at ports and intermodal facilities in the U.S. A number of ports and intermodal terminals are consid...

Vectorization, parallelization and porting of nuclear codes on the VPP500 system (porting). Progress report fiscal 1997

International Nuclear Information System (INIS)

Ishizuki, Shigeru; Nemoto, Toshiyuki; Kawai, Wataru; Watanabe, Hideo; Tanabe, Hidenobu; Kawasaki, Nobuo; Adachi, Masaaki; Ogasawara, Shinobu; Kume, Etsuo

1999-05-01

Several computer codes in the nuclear field have been vectorized, parallelized and transported on the FUJITSU VPP500 system and/or the AP3000 system at Center for Promotion of Computational Science and Engineering in Japan Atomic Energy Research Institute. We dealt with 14 codes in fiscal 1997. These results are reported in 3 parts, i.e., the vectorization part, the parallelization part and the porting part. In this report, we describe the porting. In this porting part, the porting of transient reactor analysis code TRAC-BF1 and Monte Carlo radiation transport code MCNP4A on the AP3000 are described. In addition, a modification of program libraries for command-driven interactive data analysis plotting program IPLOT is described. In the vectorization part, the vectorization of multidimensional two-fluid model code ACE-3D for evaluation of constitutive equations, statistical decay code SD and three-dimensional thermal analysis code for in-core test section (T2) of HENDEL SSPHEAT are described. In the parallelization part, the parallelization of cylindrical direct numerical simulation code CYLDNS44N, worldwide version of system for prediction of environmental emergency dose information code WSPEEDI, extension of quantum molecular dynamics code EQMD and three-dimensional non-steady compressible fluid dynamics code STREAM are described. (author)

The “diamond port configuration”: A standardised laparoscopic ...

African Journals Online (AJOL)

This covered patient position, port insertion, technical aspects of intestinal resection and perioperative management. In particular, a diamond configuration for ports was agreed upon. Data were prospectively collected, and included patient demographics, operative times, conversion rates and postoperative outcomes.

Structural Analysis of Port Brand Equity Using Structural Equation Modeling1

Directory of Open Access Journals (Sweden)

Taehwee Lee

2014-12-01

Full Text Available Port competition, especially in the Northeast Asia (NEA region, can be described as a price war. In this price competition, it is necessary to build up the brand concept to acquire higher market share. This paper aims to provide structural relationships for port brand equity (PBE and explore the PBE stages statistically. The stages are divided into three steps: port service quality as the precedent of PBE, the PBE dimensions (brand awareness [BA] and brand loyalty [BL], and the antecedent of PBE (overall value of brand equity [OVBE]. From a survey conducted with port users in Korea, the empirical results revealed several significant relationship: between tangibles (TA dimension of port service quality and BL, between the empathy (EMP dimension of port service quality and both BA and BL, and between BA and BL and OVBE. From the empirical analysis, this study suggests both managerial and academic contributions for port managers and scholars for further policy development and research in this important area.

Effectively reducing emissions from ports

Energy Technology Data Exchange (ETDEWEB)

Fazlagic, Ismir; Martelin, Marcus; Skinner, Ryan

2010-09-15

Commercial ships calling at more and more ports worldwide can now turn off their diesel engines and tap into cleaner energy sources provided by electrical connections from shore. The technology to make this possible has been in place for over a decade. With a global technology standard due to be ratified by three technical bodies in 2010, high-voltage shore connections will soon get much more attention. Environmentally-minded ports, governments and shipowners are all tuning in to the benefits of supplying electricity to ships at berth. ABB presents the challenge, the technical solution and the business case for all parties involved.

INSTITUTIONAL BARRIERS TO EFFICIENT POLICY INTERVENTION IN THE EUROPEAN PORT SECTOR

Directory of Open Access Journals (Sweden)

Barry UBBELS

2005-01-01

Full Text Available Despite the growing role of private involvement in recent port developments, most maritime trade is still largely handled in ports where investments, pricing and other managerial decisions are, to a varying extent, dependent, or at least influenced by public bodies. This paper shows that the extent and type of public intervention differs considerably between ports in the Hamburg-Le Havre range. The wide variety in ownership, financing and management of ports throughout Europe indicates that there is no level playing field at present. Because ports operate in an increasingly competitive environment (intensified by globalisation trends and the completion of the internal market, this may lead to situations of unfair competition. The European Union emphasises the importance of a more harmonised approach of port regulation by national governments (in terms of financing and pricing of infrastructure. Given the differences in (national port management styles and the low levels of transparency, the creation of a level playing field in the European port industry seems far away. This suggests the presence of a major institutional difference in European transport policy that hampers efficient policy intervention.

Graviatoms with de Sitter Interior

Directory of Open Access Journals (Sweden)

Irina Dymnikova

2013-01-01

Full Text Available We present a graviatom with de Sitter interior as a new candidate to atomic dark matter generically related to a vacuum dark energy through its de Sitter vacuum interior. It is a gravitationally bound quantum system consisting of a nucleus represented by a regular primordial black hole (RPBH, its remnant or gravitational vacuum soliton G-lump, and a charged particle. We estimate probability of formation of RPBHs and G-lumps in the early Universe and evaluate energy spectrum and electromagnetic radiation of graviatom which can in principle bear information about a fundamental symmetry scale responsible for de Sitter interior and serve as its observational signatures.

A cost-effective peripheral venous port system placed at the bedside.

Science.gov (United States)

Finney, R; Albrink, M H; Hart, M B; Rosemurgy, A S

1992-07-01

High costs and a paucity of available operating time have led us to seek alternatives to operatively placed vascular access systems. This prospective study is the initial report of a peripheral port system (P.A.S. PORT System, Pharmacia Deltec, Inc.) placed at the bedside. Seventy-nine patients (52 male, 27 female), ages 3-92 years, had ports implanted by surgical residents with attending supervision. Sixty-eight (86%) received the P.A.S. PORT for long-term antibiotics, antifungal, or antiviral therapy; four (5%) for TPN infusion; three (4%) for blood products; two (3%) for chemotherapy; and two (3%) for iv narcotics. Ports were placed in 10 (13%) HIV(+) patients, three (4%) who were fully anticoagulated, and one who was a hemophiliac with a platelet count of zero. Eight patients (10%) developed superficial phlebitis, all of which resolved with nonsteroidal anti-inflammatory agents within 48 hr without port removal. Seven patients (9%) had their port removed due to infection. The average hospital charge to place the P.A.S. PORT System was $1488.00 vs $2811.00 for a tunneled external chest catheter and $3729.00 for the placement of a chest port. Bedside insertion of vascular access devices can be safely performed with acceptable infection rates allowing more efficient use of hospital operating rooms and with substantial cost savings.

Shutdown dose rate contribution from diagnostics in ITER upper port 18

Energy Technology Data Exchange (ETDEWEB)

Cheon, M.S., E-mail: munseong@nfri.re.kr [National Fusion Research Institute, Daejeon (Korea, Republic of); Pak, S.; An, Y.H.; Seon, C.R.; Lee, H.G. [National Fusion Research Institute, Daejeon (Korea, Republic of); Bertalot, L.; Krasilnikov, V. [ITER Organization, St Paul-lez-Durance (France); Zvonkov, A. [Agency ITER-RF, Moscow (Russian Federation)

2016-11-01

Highlights: • The Shutdown Dose Rate in the interspace of ITER upper port 18 was evaluated. • VUV spectrometer is the dominant contributor to the average SDR. • The existence and size of the blanket cooling pipes impacts significantly on SDR. - Abstract: D-T operation of ITER plasma will produce high-energy fusion neutrons those can activate materials around the place where human-access is necessary. The interspace of the diagnostic port is one of the area where human-access is necessary for the maintenance of diagnostic systems installed at the port, so it is important to evaluate a dose rate of the interspace area in order to comply with ALARA principle. The shutdown dose rate (SDR) in the interspace of ITER upper port 18 was evaluated by the Direct 1-Step (D1S) method using MCNP5 code. This port contains three diagnostics: Vacuum Ultra-Violet (VUV) Spectrometer, Neutron Activation System (NAS), and Upper Vertical Neutron Camera (UVNC). The contribution of each diagnostic in the port was evaluated by running separate upper port MCNP models those contain individual diagnostic only, and the total dose rate contribution was evaluated with the model which was fully integrated with all the diagnostics. The effect of the opening around the upper port plug and of the other ports was also investigated. The purpose of this assessment is to provide the shielding design basis for the preliminary design of the diagnostic integration in the port. The method and result of the calculation will be presented in this paper.

Port type is a possible risk factor for implantable venous access port-related bloodstream infections and no sign of local infection predicts the growth of gram-negative bacilli.

Science.gov (United States)

Hsu, Jui-Feng; Chang, Hsu-Liang; Tsai, Ming-Ju; Tsai, Ying-Ming; Lee, Yen-Lung; Chen, Pei-Huan; Fan, Wen-Chieh; Su, Yu-Chung; Yang, Chih-Jen

2015-09-30

Implantable venous access port (IVAP)-related blood stream infections (BSIs) are one of the most common complications of implantable venous ports. The risk factors and pathogens for IVAP-related BSIs are still controversial. We retrospectively reviewed all patients who received IVAPs at a Hospital in Taiwan from January 1, 2011 to June 31, 2014. Two types of venous port, BardPort® 6.6 fr (Bard port) and Autosuture Chemosite® 7.5 fr (TYCO port) were used. All patients with clinically proven venous port-related BSIs were enrolled. A total of 552 patients were enrolled. There were 34 episodes of IVAP-related BSIs during the study period for a total incidence of 0.177 events/1000 catheter days. Port type (TYCO vs. Bard, HR = 7.105 (95% confidence interval (CI), 1.688-29.904), p = 0.0075), age > 65 years (HR = 2.320 (95 % CI, 1.179-4.564), p = 0.0148), and lung cancer (HR = 5.807 (95% CI, 2.946-11.447), p port infections. We also found that no local sign of infection was significantly associated with the growth of gram-negative bacilli (p = 0.031). TYCO venous ports, age > 65 years, and lung cancer were all significant risk factors for IVAP-related BSIs, and no sign of infection was significantly associated with the growth of gram-negative bacilli.

Port Harcourt Medical Journal, a paradigm shift | Eke | Port Harcourt ...

African Journals Online (AJOL)

Port Harcourt Medical Journal, a paradigm shift. N Eke. Abstract. No Abstract. Full Text: EMAIL FULL TEXT EMAIL FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT · http://dx.doi.org/10.4103/0795-3038.179439 · AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors ...

Comparison of Inversion (“flipping”) Rates Among Different Port Designs: A Single-Center Experience

International Nuclear Information System (INIS)

Etezadi, Vahid; Trerotola, Scott O.

2017-01-01

PurposeTo compare incidence of port inversion among different types of implantable venous access devices.Materials and Methods Records of patients who underwent imaging-guided subcutaneous port placement without port fixation between July 2001 and April 2015 were reviewed with use of a quality assurance database. 1930 patients with complete follow-up (death or explant) were included in the study. Collected data included date and indication for port placement, port type, venous access site, immediate and long-term complications, indication for removal, and total number of catheter days. BMI of patients with inverted ports was also calculated.Results Port inversion within the pocket was observed in 18 patients (0.9%) including 7/82 (9%) of Dignity ports, 4/126 (3%) of Vaxcel plastic arm ports, 3/142 (2%) of Smartports, 2/100 (2%) of Powerports, 1/14 (7%) of Vaccess ports, and 1/1421 (0.07%) of Vortex LP ports. Among these designs, the inversion rate was significantly lower in Vortex LP ports (0.1%) (P < 0.05). There was a trend toward higher inversion rate of Dignity ports, which have a rectangular design with a relatively narrow base. Mean dwell in inverted ports was 114 days (7–580).Conclusion The incidence of port inversion without suture fixation of the port base to the pocket is extremely low. The present study shows differences in inversion incidence based on port design.Level of Evidence: Case Series, Level IV.

Comparison of Inversion (“flipping”) Rates Among Different Port Designs: A Single-Center Experience

Energy Technology Data Exchange (ETDEWEB)

Etezadi, Vahid, E-mail: vahid.etezadi@umm.edu; Trerotola, Scott O., E-mail: streroto@uphs.upenn.edu [University of Pennsylvania Medical Center, Division of Interventional Radiology, Department of Radiology (United States)

2017-04-15

PurposeTo compare incidence of port inversion among different types of implantable venous access devices.Materials and Methods Records of patients who underwent imaging-guided subcutaneous port placement without port fixation between July 2001 and April 2015 were reviewed with use of a quality assurance database. 1930 patients with complete follow-up (death or explant) were included in the study. Collected data included date and indication for port placement, port type, venous access site, immediate and long-term complications, indication for removal, and total number of catheter days. BMI of patients with inverted ports was also calculated.Results Port inversion within the pocket was observed in 18 patients (0.9%) including 7/82 (9%) of Dignity ports, 4/126 (3%) of Vaxcel plastic arm ports, 3/142 (2%) of Smartports, 2/100 (2%) of Powerports, 1/14 (7%) of Vaccess ports, and 1/1421 (0.07%) of Vortex LP ports. Among these designs, the inversion rate was significantly lower in Vortex LP ports (0.1%) (P < 0.05). There was a trend toward higher inversion rate of Dignity ports, which have a rectangular design with a relatively narrow base. Mean dwell in inverted ports was 114 days (7–580).Conclusion The incidence of port inversion without suture fixation of the port base to the pocket is extremely low. The present study shows differences in inversion incidence based on port design.Level of Evidence: Case Series, Level IV.

Managing Risks in Dry Port Operations

OpenAIRE

Ciortescu Cezar-Gabriel; Pãvãla?cu Narcis Sebastian

2012-01-01

The purpose of this paper is to have an in-depth look into the phenomenon of risk assessment and risk management strategies in managing dry port operations as an integrated part into international containerized freight trade. The fact that world crises take the form of disruptions, bankruptcies, breakdowns, macroeconomic and political changes, and disasters leads to higher risks and makes risk management more and more difficult. This paper aims to discuss the theory behind the dry port concep...

Detailed Design and Fabrication Method of the ITER Vacuum Vessel Ports

International Nuclear Information System (INIS)

Hee-Jae Ahn; Kwon, T.H.; Hong, Y.S.

2006-01-01

The engineering design of the ITER vacuum vessel (VV) has been progressed by the ITER International Team (IT) with the cooperation of several participant teams (PT). The VV and ports are the components allocated to Korea for the construction of the ITER. Hyundai Heavy Industries has been involved in the structural analysis, detailed design and development of the fabrication method of the upper and lower ports within the framework of the ITER transitional arrangements (ITA). The design of the port structures has been investigated to validate and to improve the conceptual designs of the ITER IT and other PT. The special emphasis was laid on the flange joint between the port extension and the in-port plug to develop the design of the upper port. The modified design with a pure friction type flange with forty-eight pieces of bolts instead of the tangential key is recommended. Furthermore, the alternative flange designs developed by the ITER IT have been analyzed in detail to simplify the lip seal maintenance into the port flange. The structural analyses of the lower RH port have been also performed to verify the capacity for supporting the VV. The maximum stress exceeds the allowable value at the reinforcing block and basement. More elaborate local models have been developed to mitigate the stress concentration and to modify the component design. The fabrication method and the sequence of the detailed fabrication for the ports are developed focusing on the cost reduction as well as the simplification. A typical port structure includes a port stub, a stub extension and a port extension with a connecting duct. The fabrication sequence consists of surface treatment, cutting, forming, cleaning, welding, machining, and non-destructive inspection and test. Tolerance study has been performed to avoid the mismatch of each fabricated component and to obtain the suitable tolerances in the assembly at the shop and site. This study is based on the experience in the fabrication of

Remote Handling behind port plug in ITER

International Nuclear Information System (INIS)

Bede, O.; Neuberger, H.

2006-01-01

Different Test Blanket Modules (TBM) will be used in succession in the same equatorial ports of ITER. The remote handling operations for connection/disconnection of an interface between the port plug of the EU-HCPB-TBM and the port cell equipment are investigated with the goal to reach a quick and simple TBM exchange procedure. This paper describes the operations and systems which are required for connection of the TBM to its supply lines at this interface. The interface is located inside the free space of the port plug flange between the port plug shield and the bioshield of the port cell behind. The approach of the operation place is only available through a narrow gate in the bioshield opened temporarily during maintenance periods. This gate limits the dimensions of the whole system and its tools. The current design of the EU-HCPB-TBM foresees up to 9 supply lines which have to be connected inside the free space of one half of the port plug flange. The connection operations require positioning and adjustment of the tools for each pipe separately. Despite the strict circumstances it is still possible to find such an industrial jointed-arm robot with sufficient payload, which can penetrate into the working area. A mechanical system is necessary to move the robot from its storing place in the hot cell to the port plug on 6 m distance. Each operation requires different end-of-arm tools. The most special one is a pipe positioner tool, which can position and pull the pipe ends to each other and align the tool before welding and hold them in proper position during the welding process. Weld seams can be made by orbital welding tool. The pipe positioner tool has to provide place for welding tool. Using of inbore tool is impossible because pipes have no open ends where the tool could leave it. Orbital tool must be modified to meet requirements of remote handling because it is designed for human handling. The coolant is helium, so for eliminating the leak of helium it is

Soft-Tissue-Anchored Transcutaneous Port for Long-Term Percutaneous Transhepatic Biliary Drainage

International Nuclear Information System (INIS)

Nyman, Rickard; Ekloef, Hampus; Eriksson, Lars-Gunnar; Karlsson, Britt-Marie; Rasmussen, Ib; Lundgren, Dan; Thomsen, Peter

2005-01-01

Purpose. A transcutaneous port (T-port) has been developed allowing easy exchange of a catheter, which was fixed inside the device, using the Seldinger technique. The objective of the study was to test the T-port in patients who had percutaneous transhepatic biliary drainage (PTBD). Methods. The T-port, made of titanium, was implanted using local anesthesia in 11 patients (mean age 65 years, range 52-85 years) with biliary duct obstruction (7 malignant and 4 benign strictures). The subcutaneous part of the T-port consisted of a flange with several perforations allowing ingrowth of connective tissue. The T-port allowed catheter sizes of 10 and 12 Fr. Results. All wounds healed uneventfully and were followed by a stable period without signs of pronounced inflammation or infection. It was easy to open the port and to exchange the drainage tube. The patient's quality of life was considerably improved even though several patients had problems with repeated bile leakage due to frequent recurrent obstructions of the tubes. The ports were implanted for a mean time of 9 months (range 2-21 months). Histologic examination in four cases showed that the port was well integrated into the soft tissue. Tilting of the T-port in two cases led to perforation of the skin by the subcutaneous part of the ports, which were removed after 7 and 8 months. Conclusion. The T-port served as an excellent external access to the biliary ducts. The drainage tubes were well fixed within the ports. The quality of life of the patients was considerably improved. Together with improved aesthetic appearance they found it easier to conduct normal daily activities and personal care. However, the problem of recurrent catheter obstruction remained unsolved

Safety and Effectiveness of Percutaneously Inserted Peritoneal Ports Compared to Surgically Inserted Ports in a Retrospective Study of 87 Patients with Ovarian Carcinoma over a 10-Year Period

International Nuclear Information System (INIS)

Woodley-Cook, Joel; Tarulli, Emidio; Tan, Kong T.; Rajan, Dheeraj K.; Simons, Martin E.

2016-01-01

PurposePlacement of peritoneal ports has become a favorable technique for direct chemotherapy infusion in treating peritoneal metastases from ovarian cancer. We aim to outline an approach to the percutaneous insertion of peritoneal ports and to characterize success and complication rates compared to surgically inserted ports.Materials and MethodsRetrospective analysis was collected from 87 patients who had peritoneal port insertion (28 inserted surgically and 59 percutaneously) for treatment of peritoneal metastases from ovarian cancer from July 2004 to July 2014. Complications were classified according to the SIR Clinical Practice Guidelines as major or minor.ResultsTechnical success rates for surgically and percutaneously inserted ports were 100 and 96.7 %, respectively (p = 0.44), with the two percutaneous failures successful at a later date. There were no major complications in either group. Minor complication rates for surgically versus percutaneously inserted ports were 46.4 versus 22.0 %, respectively (p = 0.02). The infection rate for surgically inserted versus percutaneously inserted ports was 14.3 and 0 %, respectively (p = 0.002). The relative risk of developing a complication from percutaneous peritoneal port insertion without ascites was 3.4 (p = 0.04). For percutaneously inserted ports, the mean in-room procedure time was 81 ± 1.3 min and mean fluoroscopy time was 5.0 ± 4.5 min.ConclusionPercutaneously inserted peritoneal ports are a safe alternative to surgically inserted ports, demonstrating similar technical success and lower complication rates.

Safety and Effectiveness of Percutaneously Inserted Peritoneal Ports Compared to Surgically Inserted Ports in a Retrospective Study of 87 Patients with Ovarian Carcinoma over a 10-Year Period

Energy Technology Data Exchange (ETDEWEB)

Woodley-Cook, Joel, E-mail: jwoodleycook@gmail.com [The Scarborough Hospital, Vascular and Interventional Radiology, Department of Diagnostic Imaging (Canada); Tarulli, Emidio; Tan, Kong T.; Rajan, Dheeraj K.; Simons, Martin E. [University of Toronto, Vascular and Interventional Radiology, Department of Medical Imaging, University Health Network (Canada)

2016-11-15

PurposePlacement of peritoneal ports has become a favorable technique for direct chemotherapy infusion in treating peritoneal metastases from ovarian cancer. We aim to outline an approach to the percutaneous insertion of peritoneal ports and to characterize success and complication rates compared to surgically inserted ports.Materials and MethodsRetrospective analysis was collected from 87 patients who had peritoneal port insertion (28 inserted surgically and 59 percutaneously) for treatment of peritoneal metastases from ovarian cancer from July 2004 to July 2014. Complications were classified according to the SIR Clinical Practice Guidelines as major or minor.ResultsTechnical success rates for surgically and percutaneously inserted ports were 100 and 96.7 %, respectively (p = 0.44), with the two percutaneous failures successful at a later date. There were no major complications in either group. Minor complication rates for surgically versus percutaneously inserted ports were 46.4 versus 22.0 %, respectively (p = 0.02). The infection rate for surgically inserted versus percutaneously inserted ports was 14.3 and 0 %, respectively (p = 0.002). The relative risk of developing a complication from percutaneous peritoneal port insertion without ascites was 3.4 (p = 0.04). For percutaneously inserted ports, the mean in-room procedure time was 81 ± 1.3 min and mean fluoroscopy time was 5.0 ± 4.5 min.ConclusionPercutaneously inserted peritoneal ports are a safe alternative to surgically inserted ports, demonstrating similar technical success and lower complication rates.

49 CFR 179.12 - Interior heater systems.

Science.gov (United States)

2010-10-01

... Design Requirements § 179.12 Interior heater systems. (a) Interior heater systems shall be of approved design and materials. If a tank is divided into compartments, a separate system shall be provided for... 49 Transportation 2 2010-10-01 2010-10-01 false Interior heater systems. 179.12 Section 179.12...

Market Aspects of an Interior Design Program.

Science.gov (United States)

Gold, Judy E.

A project was conducted to evaluate a proposed interior design program in order to determine the marketability (job availability in the field of interior design and home furnishings merchandising) and the feasibility (educational requirements for entrance into the interior design and home furnishings merchandising job market) of the program. To…

Treatment of acute appendicitis with one-port transumbilical ...

African Journals Online (AJOL)

Background: Laparoscopic appendectomy is a feasible and safe alternative to open appendectomy for uncomplicated appendicitis. In the past decade several laparoscopic procedures have been described using one or more ports. We report our experience in treating acute appendicitis with one-port transumbilical ...

Port supply chain integration : analyzing biofuel supply chains

NARCIS (Netherlands)

Stevens, Leonie C. E.; Vis, Iris F. A.

2016-01-01

This paper focuses on port supply chain integration to strengthen operational and business performance. We provide a structured and comprehensive method to enable port supply chain integration and demonstrate its applicability to the biofuel supply chain. We define the value proposition, role,

Environmental reform of West and Central Africa ports

NARCIS (Netherlands)

Barnes-Dabban, Harry; Koppen, Van Kris; Mol, Arthur

2017-01-01

West and Central Africa ports have historically not paid much attention to environmental issues. In the past decade, however, environmental concerns are beginning to emerge with pockets of innovative responses to environmental risks as the ports undergo institutional and infrastructural reform –

The Long Shadow of Port Infrastructure in Germany

DEFF Research Database (Denmark)

Mitze, Timo Friedel; Breidenbach, Philipp

2016-01-01

. Since it is very likely that results from least square estimations suffer from endogeneity problems, we base the identification on exogenous long-run instruments. In particular, port facilities built before the industrial revolution provide an adequate instrument for current port infrastructure since...

The alternative means process for the Port Hope Area Initiative

International Nuclear Information System (INIS)

O'Neill, J.E.; Campbell, D.; Rossi, R.

2006-01-01

In March of 2001, the Government of Canada, the Town of Port Hope, Hope Township and the Municipality of Clarington agreed to the cleanup and long-term management of historic, low-level radioactive waste materials in these communities. The agreement identified conceptual designs for long-term management facilities for the wastes. Two environmental assessments (EAs) of the proposed long-term management facilities have been initiated as part of the Port Hope Area Initiative (PHAI); namely the Port Hope Long-Term Low-Level Radioactive Waste Management Project and the Port Granby Long-Term Low-Level Radioactive Waste Management Project. A requirement set out in the Scope for the EAs is the consideration of technically and economically feasible Alternative Means of carrying out the PHAI projects. Alternative Means are the various ways that the projects could be implemented, such as alternative technologies, sites, transportation routes, etc. Early in the overall EA processes the Low-Level Radioactive Waste Management Office (LLRWMO), which is responsible for undertaking the EAs, recognized that it was facing a significant challenge; namely, the successful completion of a clear, technically sound and defendable Alternative Means analysis, including consultation with and acceptance by the community. This would be a fundamental requirement for the success of the PHAI EAs. A further challenge was to develop consistent assessment methodologies for the Port Hope and Port Granby projects, which were both initiated under the PHAI at the same time. Although similar in many respects, the two projects have major differences. For example, the Port Hope Project, with more sources of contamination within a built- up urban area is more complex and has a broader range of potential solutions to be considered than the rural Port Granby Project. This paper describes how the LLRWMO met that challenge, developed and implemented a successful Alternative Means process and presents the

A Study on the Securement of the Competitiveness of Gyeong-In Port

Directory of Open Access Journals (Sweden)

Woo-chul Ahn

2014-08-01

Full Text Available Through empirical study of current port selection factors of import and export companies in metropolitan areas trading with China, which are likely to use Gyeong-In Port in the future due to its geographical proximity, the tendency of its use by manufacturing companies in relevant areas is analyzed, and problems and ways to strengthen the competitiveness of Gyeong-In Port are explored. Study results show that transshipment routes between nearby ports need to be established in the medium to long term. In the short term, direct routes to Qingdao Port and Tianjin Port need to be vitalized. Based on analysis results of priority and satisfaction in port selection factors, cargo volumes should be secured by providing various incentives to Gimpo terminal at Gyeong-In Port and using aggressive marketing from a logistics company on commission. A clear management strategy and active cooperation among the government, project operators of K-water, and terminal operation companies are necessary.

Assessment of Ports for Offshore Wind Development in the United States

Energy Technology Data Exchange (ETDEWEB)

Elkinton, Chris [DNV GL; Blatiak, Alicia; Ameen, Hafsa

2014-03-21

As offshore wind energy develops in the United States, port facilities will become strategic hubs in the offshore wind farm supply chain because all plant and transport logistics must transit through these facilities. Therefore, these facilities must provide suitable infrastructure to meet the specific requirements of the offshore wind industry. As a result, it is crucial that federal and state policy-makers and port authorities take effective action to position ports in the offshore wind value chain to take best advantage of their economic potential. The U.S. Department of Energy tasked the independent consultancy GL Garrad Hassan (GL GH) with carrying out a review of the current capability of U.S. ports to support offshore wind project development and an assessment of the challenges and opportunities related to upgrading this capability to support the growth of as many as 54 gigawatts of offshore wind installed in U.S. waters by 2030. The GL GH report and the open-access web-based Ports Assessment Tool resulting from this study will aid decision-makers in making informed decisions regarding the choice of ports for specific offshore projects, and the types of investments that would be required to make individual port facilities suitable to serve offshore wind manufacturing, installation and/or operations. The offshore wind industry in the United States is still in its infancy and this study finds that additional port facilities capable of supporting offshore wind projects are needed to meet the anticipated project build-out by 2030; however, no significant barriers exist to prevent the development of such facilities. Furthermore, significant port capabilities are in place today with purpose-build port infrastructure currently being built. While there are currently no offshore wind farms operating in the United States, much of the infrastructure critical to the success of such projects does exist, albeit in the service of other industries. This conclusion is based

Port Regionalization and Landlocked Hinterland: The Czech Republic

Directory of Open Access Journals (Sweden)

Jean Paul Rodrigue

2016-09-01

Full Text Available The expansion of the European Union (EU and economic growth have propelled the development of intermodal transportation and logistics activities in Central and Eastern Europe (CEE. Yet, the inland location of most CEE economies requires improved connectivity to port terminals on both the Atlantic/Baltic and Mediterranean/Black Sea ranges. The paper provides a broader research perspective on inland logistics platforms focusing on the CEE region, particularly as it concerns the role of the public sector in port hinterland infrastructure development. The paper identifies the current bottlenecks in logistics activity in regard to the whole range of the national transport chains. A dual regionalization process is taking place between the ports of the Northern and Mediterranean ranges and that the Northern Range is more effective at servicing the CEE region, including the Czech Republic, in spite of the proximity advantage of Mediterranean ports.

Ramifications of single-port laparoscopic surgery: measuring differences in task performance using simulation.

Science.gov (United States)

Conway, Nathan E; Romanelli, John R; Bush, Ron W; Seymour, Neal E

2014-02-01

Single-port laparoscopic surgery imposes unique psychomotor challenges. We used surgical simulation to define performance differences between surgeons with and without single-port clinical experience and examined whether a short course of training resulted in improved performance. Study participants were assigned to 3 groups: resident group (RES), experienced laparoscopic surgeons with (SP) and without (LAP) prior single-port laparoscopic experience. Participants performed the Fundamentals of Laparoscopic Surgery precision cutting task on a ProMIS trainer through conventional ports or with articulating instruments via a SILS Port (Covidien, Inc). Two iterations of each method were performed. Then, 6 residents performed 10 successive single-port iterations to assess the effect of practice on task performance. The SP group had faster task times for both laparoscopic (P = .0486) and single-port (P = .0238) methods. The LAP group had longer path lengths for the single-port task than for the laparoscopic task (P = .03). The RES group was slower (P = .0019), with longer path length (P = .0010) but with greater smoothness (P = .0186) on the single-port task than the conventional laparoscopic task. Resident performance task time (P = .005) and smoothness (P = .045) improved with successive iterations. Our data show that surgeons with clinical single-port surgery experience perform a simulated single-port surgical task better than inexperienced single-port surgeons. Furthermore, this performance is comparable to that achieved with conventional laparoscopic techniques. Performance of residents declined dramatically when confronted with the challenges of the single-port task but improved with practice. These results suggest a role for lab-based single-port training.

The Prefabricated Interior Design Studio: An Exploration into the History and Sustainability of Interior Prefabrication

Science.gov (United States)

Schneiderman, Deborah; Freihoefer, Kara

2013-01-01

This article examines the integration of prefabrication into an interior design studio. A review of the literature revealed that while there is a paucity of categorical research focused on this subject, the subject is historically significant with an abundance of evidence regarding the prefabrication of the interior environment dating back…

State Skill Standards: Housing and Interior Design

Science.gov (United States)

Nevada Department of Education, 2008

2008-01-01

Meeting the Housing and Interior Design Standards will provide students with skills for personal family life and towards becoming a professional in the interior design field. The mission of Housing and Interior Design education is to prepare students for family life, work life, and careers in the fashion industry by creating opportunities to…

7 CFR 319.8-22 - Ports of entry or export.

Science.gov (United States)

2010-01-01

... 7 Agriculture 5 2010-01-01 2010-01-01 false Ports of entry or export. 319.8-22 Section 319.8-22... SERVICE, DEPARTMENT OF AGRICULTURE FOREIGN QUARANTINE NOTICES Foreign Cotton and Covers Miscellaneous Provisions § 319.8-22 Ports of entry or export. When ports of entry or export are not specifically designated...

Four-port mode-selective silicon optical router for on-chip optical interconnect.

Science.gov (United States)

Jia, Hao; Zhou, Ting; Fu, Xin; Ding, Jianfeng; Zhang, Lei; Yang, Lin

2018-04-16

We propose and demonstrate a four-port mode-selective optical router on a silicon-on-insulator platform. The passive routing property ensures that the router consumes no power to establish the optical links. For each port, input signals with different modes are selectively routed to the target ports through the pre-designed architecture. In general, the device intrinsically supports broadcasting of multiplexed signals from one port to the other three ports through mode division multiplexing. In some applications, the input signal from one port would only be sent to another port as in reconfigurable optical routers. The prototype is constructed by mode multiplexers/de-multiplexers and single-mode interconnect waveguides between them. The insertion losses for all optical links are lower than 8.0 dB, and the largest optical crosstalk values are lower than -18.7 dB and -22.0 dB for the broadcasting and port-to-port routing modes, respectively, at the wavelength range of 1525-1565 nm. In order to verify the routing functionality, a 40-Gbps bidirectional data transmission experiment is performed. The device offers a promising building block for passive routing by utilizing the dimension of the modes.

7 CFR 319.55-3 - Ports of entry.

Science.gov (United States)

2010-01-01

... through Mexican border ports and such other ports as may later be approved by the Plant Protection and... Plant Protection and Quarantine Programs. (c) Pending development of adequate treating facilities in... Regulations of the Department of Agriculture (Continued) ANIMAL AND PLANT HEALTH INSPECTION SERVICE...

Safety shield for vacuum/pressure chamber viewing port

Science.gov (United States)

Shimansky, R. A.; Spencer, R. S. (Inventor)

1981-01-01

Observers are protected from flying debris resulting from a failure of a vacuum or pressure chamber viewing port following an implosion or explosion by an optically clear shatter resistant safety shield which spaced apart from the viewing port on the outer surface of the chamber.

Numerical simulation on bake-out of the ITER diagnostic upper port plug

International Nuclear Information System (INIS)

Pak, S.; Pitcher, C.S.; Kalish, M.R.; Cheon, M.S.; Seon, C.R.; Lee, H.G.

2010-01-01

The diagnostic upper port plug in ITER is fixed to the upper port of the vacuum vessel as a cantilevered beam with bolts and forms a primary vacuum boundary. It needs to be baked out for outgassing before normal operation. This study calculated the required bake-out time and the transient thermal stress during baking for the diagnostic upper port plug. The calculation was done through numerical simulation. The analysis took into consideration the gradual temperature increase of working fluid. In order to look into the effect of radiation heat transfer from the upper port plug to the vacuum vessel port, the upper vacuum vessel port was included in this analysis.

Optimisation of ported yield of hemispherical ported microparticles for soft tissue augmentation

CSIR Research Space (South Africa)

Barnard, A

2011-05-01

Full Text Available degradation period and biocompatibility. Micro-porous particles are useful in soft-tissue bulking due to their relatively large surface area, low density and high degree of porosity. In this study, the authors have developed ported porous PCL particles...

33 CFR 125.11 - Form of Coast Guard Port Security Card.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Form of Coast Guard Port Security... WATERFRONT FACILITIES OR VESSELS § 125.11 Form of Coast Guard Port Security Card. The Coast Guard Port... data. ...

Determining building interior structures using compressive sensing

Science.gov (United States)

Lagunas, Eva; Amin, Moeness G.; Ahmad, Fauzia; Nájar, Montse

2013-04-01

We consider imaging of the building interior structures using compressive sensing (CS) with applications to through-the-wall imaging and urban sensing. We consider a monostatic synthetic aperture radar imaging system employing stepped frequency waveform. The proposed approach exploits prior information of building construction practices to form an appropriate sparse representation of the building interior layout. We devise a dictionary of possible wall locations, which is consistent with the fact that interior walls are typically parallel or perpendicular to the front wall. The dictionary accounts for the dominant normal angle reflections from exterior and interior walls for the monostatic imaging system. CS is applied to a reduced set of observations to recover the true positions of the walls. Additional information about interior walls can be obtained using a dictionary of possible corner reflectors, which is the response of the junction of two walls. Supporting results based on simulation and laboratory experiments are provided. It is shown that the proposed sparsifying basis outperforms the conventional through-the-wall CS model, the wavelet sparsifying basis, and the block sparse model for building interior layout detection.

Interior design for dentistry.

Science.gov (United States)

Unthank, M; True, G

1999-11-01

In the increasingly complex, competitive and stressful field of dentistry, effectively designed dental offices can offer significant benefits. Esthetic, functional and life-cycle cost issues to be considered when developing your interior design scheme include color, finishes, lighting, furnishings, art and accessories. An appropriately designed dental office serves as a valuable marketing tool for your practice, as well as a safe and enjoyable work environment. Qualified interior design professionals can help you make design decisions that can yield optimum results within your budget.

Ultrathin SWCNT Films Enabled Multi-modal Fiber Sensors

Science.gov (United States)

2014-09-30

reinforced composite (GFRC)  laminates  embedded with SWCNT‐ FibSen sensors  A vacuum bagging process was used  to  fabricate  fiberglass  prepregs   ( Prepreg ...insights to reveal the resin curing  process. To demonstrate this point, the  laminates  of fiberglass  prepregs  respectively embedded  with glass, polyaramid...In particular,  the SWCNT‐FibSen  sensors  are able to provide the local curing information in the interior of the  laminated   prepregs , which  cannot

Cost Consequences of a Port-Related Supply Chain Disruption

Directory of Open Access Journals (Sweden)

Hui Shan LOH

2015-09-01

Full Text Available Port functionality is a significant and important aspect of cargo transportation. Previous studies have identified a list of port-related supply chain disruption threats and developed a management model that seeks to address these threats. This paper adds value to these related studies by comparing four consequences of an example of these threats: (1 avoidance of disruption, (2 mitigation of disruption, (3 deviation of transportation plan and (4 delays and deviation of transportation plan. The impact of these consequences is simulated in a case study using data from a chemical manufacturer based in Singapore. This paper quantitatively measures the impact of a port-related threat on supply chains and thus highlights the importance of port-related supply chain disruption management.

[A Comparative Study of Acute and Chronic Pain between Single Port and Triple Port Video-assisted Thoracic Surgery for Lung Cancer].

Science.gov (United States)

Li, Caiwei; Xu, Meiqing; Xu, Guangwen; Xiong, Ran; Wu, Hanran; Xie, Mingran

2018-04-20

Through the comparative analysis of the acute and chronic pain postoperative between the single port and triple port video-assisted thoracic surgery to seek the better method which can reduce the incidence of acute and chronic pain in patients with lung cancer. Data of 232 patients who underwent single port -VATS (n=131) or triple port VATS (n=101) for non-small cell lung cancer (NSCLC) on January 1, 2016 to June 30, 2017 in our hospital were analyzed. The clinical and operative data were assessed, numeric rating scale (NRS) was used to evaluate the mean pain score on the 1th, 2th, 3th, 7th, 14th days, 3th months and 6th months postoperative. Both groups were similar in clinical characteristics, there were no perioperative death in two groups. In the 1th, 2th, 7th, 14th days and 3th, 6th months postoperative, the NRS score of the single port group was superior, and the difference was significant compared with the triple port (P0.05). Univariate and multivariate analysis of the occurrence on the chronic pain showed that the operation time, surgical procedure and the 14th NRS score were risk factors for chronic pain (Pport thoracoscopic surgery has an advantage in the incidence of acute and chronic pain in patients with non-small cell lung cancer. Shorter operative time can reduce the occurrence of chronic pain. The 14th day NRS score is a risk factor for chronic pain postoperative.

33 CFR 165.813 - Security Zones; Ports of Houston and Galveston, TX.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Security Zones; Ports of Houston... Security Zones; Ports of Houston and Galveston, TX. (a) Location. Within the Ports of Houston and Galveston... yards of a cruise ship unless expressly authorized by the Coast Guard Captain of the Port Houston...

Surface Acoustic WaveAmmonia Sensors Based on ST-cut Quartz under Periodic Al Structure

Directory of Open Access Journals (Sweden)

Ming-Yau Su

2009-02-01

Full Text Available Surface acoustic wave (SAW devices are key components for sensing applications. SAW propagation under a periodic grating was investigated in this work. The theoretical method used here is the space harmonic method. We also applied the results of SAW propagation studied in this work to design a two-port resonator with an Al grating on ST-cut quartz. The measured frequency responses of the resonator were similar to the simulation ones. Then, the chemical interface of polyaniline/WO3 composites was coated on the SAW sensor for ammonia detection. The SAW sensor responded to ammonia gas and could be regenerated using dry nitrogen.

A Location-Allocation Model for Seaport-Dry Port System Optimization

Directory of Open Access Journals (Sweden)

Xuejun Feng

2013-01-01

Full Text Available Seaports participate in hinterland economic development through partnerships with dry ports, and the combined seaport-dry port network serves as the backbone of regional logistics. This paper constructs a location-allocation model for the regional seaport-dry port network optimization problem and develops a greedy algorithm and a genetic algorithm to obtain its solution. This model is applicable to situations under which the geographic distribution of demand is known. A case study involving configuration of dry ports near the west bank of the Taiwan Strait is conducted, and the model is successfully applied.

Sustainability as a procurement criterion for port investments

NARCIS (Netherlands)

Broesterhuizen, E.F.M.; Vellinga, T.; Docters van Leeuwen, L.; Taneja, P.; Zwakhals, J.W.; Nijdam, M.H.

2012-01-01

Ports are known to be one of the most polluting sectors, and therefore provide an opportunity to reduce emission significantly. Until now, the attention has been given to reduction of emissions in transport and shipping. The scope of research must expand to include port infrastructures, which should

Exploration of an ancient port: Elephanta Island (Bombay)

Digital Repository Service at National Institute of Oceanography (India)

Rao, S.R.; Gaur, A; Tripati, S.

of amphora sherds were recovered from the site. Morabandar was busy port during 4th-5th century AD as a large number of coins of this period have been found. While Shetbandar served as port till modern period. Onshore and inter tidal zone explorations brought...

76 FR 36318 - Safety Zone; Waterway Closure, Morgan City-Port Allen Route From Mile Marker 0 to Port Allen Lock

Science.gov (United States)

2011-06-22

... Executive Order 13045, Protection of Children from Environmental Health Risks and Safety Risks. This rule is not an economically significant rule and does not create an environmental risk to health or risk to...-AA00 Safety Zone; Waterway Closure, Morgan City-Port Allen Route From Mile Marker 0 to Port Allen Lock...

Symptomatic Tarlov Cysts: Surgical Treatment by Subcutaneous Infusion Port.

Science.gov (United States)

Huang, Ying; Zhu, Tong; Lin, Hongyi; Li, Jing; Zeng, Tao; Lin, Jian

2018-05-01

The treatment of Tarlov cysts is challenging and difficult. The objective of our study was to describe the security and efficacy of the subcutaneous infusion port for drainage of symptomatic Tarlov cysts. The authors executed a retrospective review of data from 5 symptomatic Tarlov cysts patients who were treated using a subcutaneous infusion port from June 2014 to July 2017. Numerical Rating Scale scores and the Japanese Orthopedic Association scores of back pain were analyzed. Complications and adverse effects on postoperative days 1, 7, 14, and 28 were also analyzed. The mean follow-up was 12.6 months. Five adults (3 females and 2 males) who had been symptomatic received a subcutaneous infusion port. After treatment, all patients experienced pain relief and pain alleviation lasted from 1 day to 3 years without complications and adverse effects. A subcutaneous infusion port is a useful treatment option for symptomatic Tarlov cysts. When the patients' symptoms returned and the cysts repressurized, we quickly and simply drained the cysts by using the infusion port. Copyright © 2018 Elsevier Inc. All rights reserved.

Overview video diagnostics for the W7-X stellarator

Energy Technology Data Exchange (ETDEWEB)

Kocsis, G., E-mail: kocsis.gabor@wigner.mta.hu [Wigner RCP, RMI, Konkoly Thege 29-33, H-1121 Budapest (Hungary); Baross, T. [Wigner RCP, RMI, Konkoly Thege 29-33, H-1121 Budapest (Hungary); Biedermann, C. [Max-Planck-Institute for Plasma Physics, 17491 Greifswald (Germany); Bodnár, G.; Cseh, G.; Ilkei, T. [Wigner RCP, RMI, Konkoly Thege 29-33, H-1121 Budapest (Hungary); König, R.; Otte, M. [Max-Planck-Institute for Plasma Physics, 17491 Greifswald (Germany); Szabolics, T.; Szepesi, T.; Zoletnik, S. [Wigner RCP, RMI, Konkoly Thege 29-33, H-1121 Budapest (Hungary)

2015-10-15

Considering the requirements of the newly built Wendelstein 7-X stellarator a ten-channel overview video diagnostic system was developed and is presently under installation. The system covering the whole torus interior can be used not only to observe the plasma but also to detect irregular operational events which are dangerous for the stellarator itself and to send automatic warning for the machine safety. The ten tangential AEQ ports used by the diagnostic remain under atmospheric pressure, the vacuum/air interface is at the front window located at the plasma side of the AEQ port. The optical vacuum window is protected by a cooled pinhole. The Sensor Module (SM) of the intelligent camera (EDICAM) – developed especially for this purpose – is located directly behind the vacuum window. EDICAM is designed to simultaneously record several regions of interest of its CMOS sensor with different frame rate and to detect various predefined events in real time. The air cooled SM is fixed by a docking mechanism which can preserve the pointing of the view. EDICAM can withstand the magnetic field (∼3 T), the neutron and gamma fluxes expected in the AEQ port. In order to adopt the new features of the video diagnostics system both control and data acquisition and visualization and data processing softwares are developed.

Overview video diagnostics for the W7-X stellarator

International Nuclear Information System (INIS)

Kocsis, G.; Baross, T.; Biedermann, C.; Bodnár, G.; Cseh, G.; Ilkei, T.; König, R.; Otte, M.; Szabolics, T.; Szepesi, T.; Zoletnik, S.

2015-01-01

Considering the requirements of the newly built Wendelstein 7-X stellarator a ten-channel overview video diagnostic system was developed and is presently under installation. The system covering the whole torus interior can be used not only to observe the plasma but also to detect irregular operational events which are dangerous for the stellarator itself and to send automatic warning for the machine safety. The ten tangential AEQ ports used by the diagnostic remain under atmospheric pressure, the vacuum/air interface is at the front window located at the plasma side of the AEQ port. The optical vacuum window is protected by a cooled pinhole. The Sensor Module (SM) of the intelligent camera (EDICAM) – developed especially for this purpose – is located directly behind the vacuum window. EDICAM is designed to simultaneously record several regions of interest of its CMOS sensor with different frame rate and to detect various predefined events in real time. The air cooled SM is fixed by a docking mechanism which can preserve the pointing of the view. EDICAM can withstand the magnetic field (∼3 T), the neutron and gamma fluxes expected in the AEQ port. In order to adopt the new features of the video diagnostics system both control and data acquisition and visualization and data processing softwares are developed.

Organizational and Managerial Structures, Financing and Other Elements of the Port System of Slovenia

Directory of Open Access Journals (Sweden)

Milojka Počuča

2007-01-01

Full Text Available The article gives a presentation of the port system of theRepublicof Slovenia and of the organizational, ownership andmanagerial structure of Slovenia's only cargo port in Koper.The analysis of the organizational, ownership and managerialstructure was carried out according to the methodology appliedin the European project entitled "Commission Staff WorkingProject on Public Financing and Charging Practices in theCommunity Sea Port Sector". The article performs a compara·tive analysis of the port of Koper with other ports of the EU inthe domain of organization, ownership and management, publicfinancing, accountancy monitoring of public money investedin the port infrastructure, principles of cost recovery ofinvested capital and possibilities of access of port operators tothe port infrastructure of the Slovenian cargo port. The articlepoints to the possibilities of ownership and managementchanges in the port of Koper.

A web-based screening tool for near-port air quality assessments

Science.gov (United States)

The Community model for near-PORT applications (C-PORT) is a screening tool with an intended purpose of calculating differences in annual averaged concentration patterns and relative contributions of various source categories over the spatial domain within about 10 km of the port...

Deepwater Ports in US waters as of August 2013

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Deepwater Port Licensing Program is the application process designed to promote the construction of LNG and oil deepwater ports. This license system was...

The Port Hope area initiative municipal involvement

International Nuclear Information System (INIS)

Austin, Rick; Stevenson, Mark

2006-01-01

Port Hope (Canada) contains one of the world's oldest nuclear facility sites. From the 1930's through to the 1970's, processing residues from radium refining facilities located at the Port Hope Harbour were being stored and/or deposited on numerous sites throughout the municipality. For a variety of reasons, including spillage of material during transportation and un-monitored or unauthorized diversion of materials, many private and public properties in the municipality were contaminated with low level radioactive waste. Over the past 30 years, the community has demanded that the nuclear industry and the federal government clean up the mess left in Port Hope. In the 1980's and 1990's, the federal government sought to fulfill its commitment to clean up over one million cubic metres of contaminated material remaining in Port Hope but was unable to find a solution. The Low Level Radioactive Waste Management Siting Task Force worked in trying to find a home for historic LLRW in the 1980's and 1990's. It is only within the past 6 years that Port Hope's community began to see the 'light at the end of the tunnel'. And, the light began to shine when the communities took the issue of long term management of the waste into their own hands and proposed possible solutions to the federal government. So the Port Hope Area Initiative is a community-based initiative. In this paper the author presents some of the reasons for success (so far) and some opportunities and challenges that his municipality, and specifically municipal Council, faces as a partner in this Environmental Assessment and project development process. He addresses some of the key elements of the Project that he believes have led to the success of the Project to this point, including: the Legal Agreement and Agreement Monitoring process; the Property Value Protection Program; the Hosting Fee; the Municipal veto on some decisions; the end Use as an asset to the Community; the Value of Peer Review. He also touches

Operational Optimization in Port Container Terminals

DEFF Research Database (Denmark)

As a result of the significant increase in worldwide containerized transportation the development of efficient handling systems in marine terminals has become very important for port competitiveness. In order to optimize the productivity the total handling time for containers in the terminal must...... be minimized. An overview of the different operational problems in port container terminals is presented and an aggregated model and solution approach is shown. Next, there will be focused on the yard storage problem and a mathematical formulation and solution proposals will be presented....

Environmental and health impact assessment for ports in Thailand.

Science.gov (United States)

Chanchang, Chamchan; Sithisarankul, Pornchai; Supanitayanon, Thanawat

2016-01-01

Port development in Thailand is an essential part of the national maritime interest in connection with ship and shore activities. The growth of maritime industry and transportation has led to the expansion of ports' areas and capacity. Each port type causes different environmental impacts. Therefore, the Port Authority of Thailand has set up guidelines on ports' environmental management. This is divided into 3 major phases; namely, planning, construction and operation commencement periods. The Report of Environmental and Health Impact Assessment (EIA, HIA and EHIA) is regarded as the environmental management process in the planning period. It is a key tool to anticipate and prevent any adverse effects that might occur on the environment as well as community health resulting from the project implementation. This measure, in turn, creates advance preparation on both the preventive and problem-solving means before the project gets off the ground. At present, the majority of new projects on port development have still been in the process of information gathering for EHIA submission. Some cannot start to operate due to their EHIA failure. For example, the Tha-sala port which did not pass EHIA, mainly because emphasis had been focused on adhering to legal regulations without taking into consideration the in-depth analysis of data being conducted by community entities in the area. Thus caused the project to be finally abolished. Impact assessment on environment and health should be aimed at detailed understanding of the community in each particular area so that effective data of objective achievement in preventing environmental problems could actually be carried out and welcomed by the concerned society.

HFB : A FASTBUS multi event double port buffer memory

International Nuclear Information System (INIS)

Cerrito, L.; Lebbolo, H.

1986-01-01

The authors describe here the FB double port buffer memory developed at the LPNHE of the University Paris VI. Its purposes are to make available same features useful in the High Energy environment, to reduce, for a given amount of memory, the dead time data collection in a large size (in term of read-out channels) High Energy experiment and to get a buffer of memory as cheap and reliable as possible. The FB protocol, on the crate and cable side, is exploited using the coupler on 4 PAL's developed by G.Fremont and E.Sanchis. The DATA-Space is divided in 4 independent smaller blocks in a way such that a block can be accessed from a port while a different block is accessed from the other port. The two ports are: A, the FB crate port and B, the FB cable port. The buffer works as a rotary FIFO, looping over the 4 blocks of memory, but allowing for any random access. A mechanism is implemented on the board in order to be able to link different modules placed everywhere. If there are m modules, the looping will be around m 4 memory blocks. A multi event function is implemented on the board. HFB is quiped of two NTA for the DATA-Space on the port ''A'', and a flag to choose between them, to allow for a FB spying of DATA during the DAS dead time. HFB is a buffer of memory which can be used at each stage of a DAS: Frontend, Intermediate (MEB) or final, being completely FB standard. The HFB was designed for the LEP data acquisition system

Single Interdigital Transducer Approach for Gravimetrical SAW Sensor Applications in Liquid Environments

Directory of Open Access Journals (Sweden)

Vu Hoa Nguyen

2017-12-01

Full Text Available Surface acoustic wave (SAW devices are well known for mass-sensitive sensor applications. In biosensing applications, chemical and biochemically evoked binding processes on surfaces are detected in liquid environments using delay line or resonator sensor configurations, preferably in combination with the appropriate microfluidic devices. All configurations share the common feature of analyzing the transmission characteristic of the propagating SAW. In this paper, a novel SAW-based impedance sensor type is introduced which uses only one interdigital transducer (IDT, simultaneously as the SAW generator and the sensor element. Here, the input port reflection coefficient S11 is measured at the IDT instead of the commonly used S21 transmission forward gain parameter. Thus, a sharp and distinct peak of the S11 spectrum is obtained, enabling a comfortable direct readout of the sensor signal. Proof of the concept was gained by analyzing the specific binding of the 4-mercaptophenylacetic acid gold nanoparticles (MPA–AuNP directly to the IDT surface. The corresponding binding kinetic of the MPA–AuNP on the functionalized gold surface has been analyzed and a sensitivity of 7.4 mΩ nM−1 has been determined.

Developing Port Klang as National Load Centre and Regional Hub Through Synchronized Supply Chain and Efficient Port Operation

OpenAIRE

Fong, Loo Ming

2007-01-01

The ocean covers more than two third of the earth’s surface and this provides immense maritime opportunities in marine transportation and trade. Ships that ply the maritime domain are primary mode of transportation and carry about 80% of the world trade volume (Organisation of Economic Cooperation and Development, OECD July 2003). Port Operations and ancillary services such as freight forwarding, shipping play an enormous role in generating economic growth. Seaborne trades through port termin...

A Mixed Integer Programming for Port Anzali Development Plan

OpenAIRE

Mahdieh Allahviranloo

2009-01-01

This paper introduces a mixed integer programming model to find the optimum development plan for port Anzali. The model minimizes total system costs taking into account both port infrastructure costs and shipping costs. Due to the multipurpose function of the port, the model consists of 1020 decision variables and 2490 constraints. Results of the model determine the optimum number of berths that should be constructed in each period and for each type of cargo. In addition to, the results of se...

Two port network analysis for three impedance based oscillators

KAUST Repository

Said, Lobna A.

2011-12-01

Two-port network representations are applied to analyze complex networks which can be dissolved into sub-networks connected in series, parallel or cascade. In this paper, the concept of two-port network has been studied for oscillators. Three impedance oscillator based on two port concept has been analyzed using different impedance structures. The effect of each structure on the oscillation condition and the frequency of oscillation have been introduced. Two different implementations using MOS and BJT have been introduced. © 2011 IEEE.

Dual-port distal gastrectomy for the early gastric cancer.

Science.gov (United States)

Kashiwagi, Hiroyuki; Kumagai, Kenta; Monma, Eiji; Nozue, Mutsumi

2015-06-01

Although recent trends in laparoscopic procedures have been toward minimizing the number of incisions, four or five ports are normally required to complete laparoscopic gastrectomy because of the complexity of this procedure. Multi-channel ports, such as the SILS port (Covidien, JAPAN), are now available and are crucial for performing single-incision laparoscopic surgery (SILS) or reduced port surgery (RPS). We carried out reduced port distal gastrectomy (RPDG) using a dual-port method with a SILS port. Ten patients who were diagnosed as early stage gastric cancer were offered the RPDG. Mean age and body mass index (BMI) were 68.1 and 21.4, respectively. No distant metastasis or regional lymph node swelling was seen in any case. A 5-mm flexible scope (Olympus, JAPAN) and SILS port were used and a nylon ligature with a straight needle, instead of a surgical instrument, was available to raise the gastric wall. The average operative time was 266.9 ± 38.3 min and blood loss was 37.8 ± 56.8 ml. Patients recovered well and experienced no complications after surgery. All patients could tolerate soft meals on the first day after surgery and the average hospital stay was 8.1 days. Past conventional LAG cases were evaluated to compare the short-term outcome and no difference was seen in the mean operative time or operative blood loss. The length of hospital stay after surgery was shorter for the RPDG group than the conventional operation group (p < 0.0001). Interestingly, the trend of serum CRP elevation after surgery was lower in the RPDG group than the conventional LAG group (p = 0.053). Although the benefits of RPS have not been established, this type of surgery may be expected to have some advantages. Cosmetic benefits and shorter hospital stays are clear advantages. Less invasiveness can be expected according to the trend of serum CRP elevation after RPDG.

Investing in Port Infrastructure to Lower Trade Costs in East Asia

Directory of Open Access Journals (Sweden)

Kazutomo Abe

2011-06-01

Full Text Available We examine how port infrastructure affects trade and role of transport costs in driving exports and imports for East Asia. Existing studies use survey indexes to explain transport costs. These do not link investment in port infrastructure to transport costs. We include in our estimates a variable to represent the congestion of the ports to explain the transport costs. We find that the port congestion has significantly increased the transport costs from East Asia to the United States. Our analysis suggests that increase in port capacity by 10 percent could cut transport cost in East Asia by up to three percent. This translates into a 0.3 to 0.5 percent across-the-board tariff cut.

Structural sensing of interior sound for active control of noise in structural-acoustic cavities.

Science.gov (United States)

Bagha, Ashok K; Modak, S V

2015-07-01

This paper proposes a method for structural sensing of acoustic potential energy for active control of noise in a structural-acoustic cavity. The sensing strategy aims at global control and works with a fewer number of sensors. It is based on the established concept of radiation modes and hence does not add too many states to the order of the system. Acoustic potential energy is sensed using a combination of a Kalman filter and a frequency weighting filter with the structural response measurements as the inputs. The use of Kalman filter also makes the system robust against measurement noise. The formulation of the strategy is presented using finite element models of the system including that of sensors and actuators so that it can be easily applied to practical systems. The sensing strategy is numerically evaluated in the framework of Linear Quadratic Gaussian based feedback control of interior noise in a rectangular box cavity with a flexible plate with single and multiple pairs of piezoelectric sensor-actuator patches when broadband disturbances act on the plate. The performance is compared with an "acoustic filter" that models the complete transfer function from the structure to the acoustic domain. The sensing performance is also compared with a direct estimation strategy.

Ergon-trial: ergonomic evaluation of single-port access versus three-port access video-assisted thoracic surgery.

Science.gov (United States)

Bertolaccini, Luca; Viti, Andrea; Terzi, Alberto

2015-10-01

Single-port access video-assisted thoracic surgery (VATS), a technique progressively developed from the standard three-port approach in minimally invasive surgery, offers ergonomic advantages but also new challenges for the surgeon. We compared the ergonomics of three-port versus single-port VATS. Posture analysis of surgeons was evaluated during 100 consecutive VATS wedge resections (50 triportal vs. 50 uniportal). Technically demanding procedures (major lung resection) were excluded. Operating table height, monitor height, distance and inclination were adjusted according to operator preference. Body posture was assessed by measuring head-trunk axial rotation and head flexion. Perceived physical strain was self-evaluated on the Borg Category Ratio (CR-10) scale. Mental workload was assessed with the National Aeronautics Space Administration-Task Load indeX (NASA-TLX), a multidimensional tool that rates workloads on six scales (mental, physical and temporal demand; effort; performance; frustration). All procedures were completed without complications. Head-trunk axial rotation was significantly reduced and neck flexion significantly improved in uniportal VATS. Viewing direction significantly declined (p = 0.01), body posture as measured on the Borg CR-10 scale was perceived as more stressful and the NASA-TLX score for overall workload was higher (p = 0.04) during triportal VATS. The NASA-TLX score for frustration was higher with uniportal VATS (p = 0.02), but the score for physical demand was higher in triportal VATS (p = 0.006). The surgeon can maintain a more neutral body posture during uniportal VATS by standing straight and facing the monitor with only minimal neck extension/rotation; however, frustration is greater than with triportal VATS.

33 CFR 80.1440 - Port Allen, Kauai, HI.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Port Allen, Kauai, HI. 80.1440 Section 80.1440 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY INTERNATIONAL NAVIGATION RULES COLREGS DEMARCATION LINES Pacific Islands § 80.1440 Port Allen, Kauai, HI. A line drawn from...

Very High Frequency Two-Port Characterization of Transistors

DEFF Research Database (Denmark)

Hertel, Jens Christian; Nour, Yasser; Jørgensen, Ivan Harald Holger

To properly use transistors in VHF converters, they need to be characterized under similar conditions. This research presents a two-port method, using a network analyzer (NWA) with a S-port setup. The method is a one-shot method, providing fast results of the off-state parasitics of the transistors....

Radiation and Shipping Port Security | RadTown USA | US ...

Science.gov (United States)

2017-08-07

Cargo comes into the U.S. from all over the world. Ports can ensure safety by: Screening cargo for radiation before it gets here. Safely handling any radioactive material that needs to pass through a port.

Relative Efficiencies of ASEAN Container Ports based on Data Envelopment Analysis

Directory of Open Access Journals (Sweden)

Nikola Kutin

2017-07-01

Full Text Available Ports play a critical role in the economies of many countries in the ASEAN region. Efficient ports facilitate a country's imports and exports, and the “relative efficiency” of a port is evaluated based on its efficiency compared to others in its group. This study analyzes the relative efficiencies of 50 ASEAN container ports and terminals. These ports are categorized according to their container handling system and location (those located in a riverbank connected to the sea are called “inland seaports” and those by the seaside are called “seaports”. The traditional output-oriented data envelopment analysis method is applied, and measures of super-efficiency constant returns to scale are estimated in order to compare the units situated on the efficiency frontier. The findings may support port managers in the ASEAN region to make decisions on whether to increase container traffic. In addition, policymakers may consider the evaluation results in deciding whether to improve the trans-ASEAN transport network and ASEAN trade competitiveness.

High Efficiency Non-isolated Three Port DC-DC Converter for PV-Battery Systems

DEFF Research Database (Denmark)

Tomas Manez, Kevin; Anthon, Alexander; Zhang, Zhe

2016-01-01

This paper presents a nonisolated Three Port Converter (TPC) with a unidirectional port for photovoltaic (PV) panels and a bidirectional port for energy storage. With the proposed topology single power conversion is performed between each port, so high efficiencies are obtained. A theoretical...

National- to port-level inventories of shipping emissions in China

Science.gov (United States)

Fu, Mingliang; Liu, Huan; Jin, Xinxin; He, Kebin

2017-11-01

Shipping in China plays a global role, and has led worldwide maritime transportation for the last decade. However, without taking national or local port boundaries into account, it is impossible to determine the responsibility that each local authority has on emission controls, nor compare them with land-based emissions to determine the priority for controlling these emissions. In this study, we provide national- to port-level inventories for China. The results show that in 2013, the total emissions of CO, non-methane volatile organic compounds (NMVOCs), nitrogen oxides (NO x ), particulate matter (PM), SO2 and CO2 were 0.0741 ± 0.0004 Tg•yr-1, 0.0691 ± 0.0004 Tg•yr-1, 1.91 ± 0.01 Tg•yr-1, 0.164 ± 0.001 Tg•yr-1, 1.30 ± 0.01 Tg•yr-1 and 86.3 ± 0.3 Tg•yr-1 in China, respectively. By providing high-resolution spatial distribution maps of these emissions, we identify three hotspots, centered on the Bohai Rim Area, the Yangtze River Delta and Pearl River Delta. These three hotspots account for 8% of the ocean area evaluated in this study, but contribute around 37% of total shipping emissions. Compared with on-road mobile source emissions, NO x and PM emissions from ships are equivalent to about 34% and 29% of the total mobile vehicle emissions in China. Moreover, this study provides detailed emission inventories for 24 ports in the country, which also greatly contributes to our understanding of global shipping emissions, given that eight of these ports rank within the top twenty of the port league table. Several ports in China suffer emissions 12-147 times higher than those at Los Angeles port. The ports of Ningbo-Zhou Shan, Shanghai, Hong Kong and Dalian dominate the port-level inventories, with individual emissions accounting for 28%-31%, 10%-14%, 10%-12% and 8%-14% of total emissions, respectively.

Two-port cholecystectomy maintains safety and feasibility in benign gallbladder diseases: a comparative study.

Science.gov (United States)

Lee, Sang Chul; Choi, Byeong-Jo; Kim, Say-June

2014-01-01

In an effort to overcome the limitations of single-port laparoscopic cholecystectomy (LC) while preserving the cosmetic benefits of reduced ports cholecystectomy, we have developed a 2-port LC that allows for the full, unrestricted use of 4 laparoscopic instruments. We retrospectively analyzed data of patients who had undergone either 4-port LC or 2-port LC for benign gallbladder diseases between March 2007 and March 2013. Two incisions of 2-port LC were composed of an umbilical incision as the manner of single-port laparoscopic surgery and a 5-mm epigastric incision. These two incisions were utilized for comfortable bimanual manipulation under the liver-elevated vision provided by a liver retractor. During the study period, 766 patients underwent LC; 263 (34.3%) started with 4-port LC, and 503 (65.7%) started with 2-port LC. Of patients started with 2-port LC, 486 patients (96.6%) was ended up with 2-port without open conversion or addition of port(s). The two groups had similar operative time, open conversion rate, incidence of complications, analgesic requirement, and length of postoperative hospital stay. Multivariate analyses revealed that the independent factors related to prolonged operative time (≥ 90 th percentile) in 2-port LC were the presence of cholecystitis (odds ratio [OR] 2.412, 95% CI 1.246-4.668, p = 0.009) and admission through the emergency department (OR 2.132, 95% CI 1.135-4.004, p = 0.019). This study suggests that 2-port LC for benign gallbladder diseases is as safe and feasible as 4-port LC when it is performed by surgeons trained in conventional laparoscopic techniques. Copyright © 2014 Surgical Associates Ltd. Published by Elsevier Ltd. All rights reserved.

Space station interior design: Results of the NASA/AIA space station interior national design competition

Science.gov (United States)

Haines, R. F.

1975-01-01

The results of the NASA/AIA space station interior national design competition held during 1971 are presented in order to make available to those who work in the architectural, engineering, and interior design fields the results of this design activity in which the interiors of several space shuttle size modules were designed for optimal habitability. Each design entry also includes a final configuration of all modules into a complete space station. A brief history of the competition is presented with the competition guidelines and constraints. The first place award entry is presented in detail, and specific features from other selected designs are discussed. This is followed by a discussion of how some of these design features might be applied to terrestrial as well as space situations.

RIVERS AND PORTS IN TRANSPORT HISTORY OF CAMEROON ...

African Journals Online (AJOL)

Dean SPGS NAU

importance of the ports in the development of the cities and the migration of people ... known to have developed in this region with technological .... Douala port as a case study. .... taking place. Traders came from West African coast, Greece and. France. .... global networks have not been limited to particular hubs but rather.

Ports: Definition and study of types, sizes and business models

Directory of Open Access Journals (Sweden)

Ivan Roa

2013-09-01

Full Text Available Purpose: In the world today there are thousands of port facilities of different types and sizes, competing to capture some market share of freight by sea, mainly. This article aims to determine the type of port and the most common size, in order to find out which business model is applied in that segment and what is the legal status of the companies of such infrastructure.Design/methodology/approach: To achieve this goal, we develop a research on a representative sample of 800 ports worldwide, which manage 90% of the containerized port loading. Then you can find out the legal status of the companies that manage them.Findings: The results indicate a port type and a dominant size, which are mostly managed by companies subject to a concession model.Research limitations/implications: In this research, we study only those ports that handle freight (basically containerized, ignoring other activities such as fishing, military, tourism or recreational.Originality/value: This is an investigation to show that the vast majority of the studied segment port facilities are governed by a similar corporate model and subject to pressure from the markets, which increasingly demand efficiency and service. Consequently, we tend to concession terminals to private operators in a process that might be called privatization, but in the strictest sense of the term, is not entirely realistic because the ownership of the land never ceases to be public

Port competition and selection in contestable hinterlands : the case of Austria

NARCIS (Netherlands)

Langen, de P.W.

2007-01-01

This paper deals with port competition and port selection for cargo to/from Austria. Austria is located centrally in Europe and seaports in at least five countries are used for imports and exports. Changes of market shares over time of different ports serving Austria are analysed. Switching of cargo

LOCATION AND POTENTIAL PORT OF GDYNIA AS ELEMENTS OF ITS COMPETITIVENESS

Directory of Open Access Journals (Sweden)

Adam Salomon

2017-06-01

Full Text Available The main aim of this article is to characterize the current operation of the port of Gdynia. Another goal is to describe the port’s location and potential for cargo handling and storage in 2007-2015 as factors determining competitiveness. The article focuses on the characteristics of the port in Gdynia, taking into account its geographical location and specialization. The article analyses the legal basis of operation of the port, its capital and organizational structure as well as governing bodies. In addition, the major universal and specialist terminals operating in the port area are described. The article also discusses the most important investments made in the port in 2007-2015 to improve its operation and ensure the best quality of service.

Registrador portátil de odorantes basado en la modulación de temperatura de un sensor mos comercial

Directory of Open Access Journals (Sweden)

Andy Blanco Rodríguez

2013-01-01

Full Text Available A simple, portable and low-cost system for odor detection was developed using a single MOS commercial sensor and a microcontroller. The temperature modulation technique was implemented applying a DC signal pulse to the sensor heater by a bipolar transistor. Two odorant profiles, ethanol and acetic acid vapors, were obtained and distinguished based on their amplitude versus time responses. Response for acetic acid was not reported by the sensor manufacturer. An ethanol vapor calibration curve was also obtained. Experimental data showed a potential behavior according to the theoretical equation of the MOS sensors. Values of logK=0.457 and α=-0.213 for a 95% confidence level were obtained.

Planning of Terminal Construction at the Port of Ploce

Directory of Open Access Journals (Sweden)

Čedomir Dundović

2007-07-01

Full Text Available The paper presents a systematic and comprehensive analysisof both the technological justification for the constructionof a container/multi-purpose terminal and a dry bulk terminal,and the efficiency of loading/unloading facilities. The organisationof Croatian ports is inefficient and the technology usedin outdated. Traffic links with the mainland, the continent andthe world are unsatisfactory, with traffic infrastructure impactingadversely on operational efficiency. Analysis results of thepresent condition of port traffic and the influence of traffic onport operations and development indicate that the Port ofPlace lacks a multi-purpose terminal that would enable modemcontainer traffic. Because of the inefficient cargo-handlingprocedure and manner of storing bulk cargo in the Port ofPlace, it is necessary to plan the construction of a coal andiron ore terminal taking into account spatia~ technological,economic and ecological development factors. The authorsalso examine the importance of regional initiatives spurringthe development of Croatia and, in particular, the port systemas part of the EU's Pan-European transport corridor V BranchC. Research results are presented by a traffic and technologicaldesign for a container/multi-purpose terminal and dry bulkterminal capable of providing an appropriate level of servicefor all terminal users.

Single port access for laparoscopic lateral segmentectomy.

Science.gov (United States)

Inoue, Yoshihiro; Asakuma, Mitsuhiro; Hirokawa, Fumitoshi; Hayashi, Michihiro; Shimizu, Tetsunosuke; Uchiyama, Kazuhisa

2017-12-01

Single-port access laparoscopic lateral segmentectomy (LLS) has been developed as a novel minimally invasive surgery. We have experience with this LLS technique. To report our technique and patients' postoperative course in a series of single-port access LLS performed in our department. We also examine the cosmetic outcome, safety, and utility of the procedure. Between February 2010 and October 2016, 54 patients who underwent single- or multiple-port laparoscopic or open lateral segmentectomy (LS) were retrospectively analyzed with respect to cosmetic outcome, safety, and utility. In the single LLS group, the laparoscopic procedure was successfully completed for all 14 patients. The median operative time was significantly shorter in the single LLS group (123 min; range: 50-270 min) than in the other groups. Estimated blood loss was also significantly lower in the single LLS group (10 ml; range: 0-330 ml). During the first 7 postoperative days, the visual analog scale pain score and the use of additional analgesia were not significantly different between groups. The single LLS group had a 7.1% complication rate (Clavien-Dindo classification > IIIA); this was not significantly different between groups. Single-port access LLS is a procedure with excellent cosmetic results, although, with regard to invasiveness, there are no major differences from conventional LLS.

A Novel Particulate Matter 2.5 Sensor Based on Surface Acoustic Wave Technology

Directory of Open Access Journals (Sweden)

Jiuling Liu

2018-01-01

Full Text Available Design, fabrication and experiments of a miniature particulate matter (PM 2.5 sensor based on the surface acoustic wave (SAW technology were proposed. The sensor contains a virtual impactor (VI for particle separation, a thermophoretic precipitator (TP for PM2.5 capture and a SAW sensor chip for PM2.5 mass detection. The separation performance of the VI was evaluated by using the finite element method (FEM model and the PM2.5 deposition characteristic in the TP was obtained by analyzing the thermophoretic theory. Employing the coupling-of-modes (COM model, a low loss and high-quality SAW resonator was designed. By virtue of the micro electro mechanical system (MEMS technology and semiconductor technology, the SAW based PM2.5 sensor detecting probe was fabricated. Then, combining a dual-port SAW oscillator and an air sampler, the experimental platform was set up. Exposing the PM2.5 sensor to the polystyrene latex (PSL particles in a chamber, the sensor performance was evaluated. The results show that by detecting the PSL particles with a certain diameter of 2 μm, the response of the SAW based PM2.5 sensor is linear, and in accordance with the response of the light scattering based PM2.5 monitor. The developed SAW based PM2.5 sensor has great potential for the application of airborne particle detection.

National Port Strategy Assessment: Reducing Air Pollution and Greenhouse Gases at U.S. Ports

Science.gov (United States)

The assessment finds that air pollution at the Nation's ports can be significantly reduced by implementing currently available strategies and technologies to reduce emissions of harmful pollutants from diesel vehicles and engines.

Simulating storm surge inundation and damage potential within complex port facilities

Science.gov (United States)

Mawdsley, Robert; French, Jon; Fujiyama, Taku; Achutan, Kamalasudhan

2017-04-01

Storm surge inundation of port facilities can cause damage to critical elements of infrastructure, significantly disrupt port operations and cause downstream impacts on vital supply chains. A tidal surge in December 2013 in the North Sea partly flooded the Port of Immingham, which handles the largest volume of bulk cargo in the UK including major flows of coal and biomass for power generation. This flooding caused damage to port and rail transport infrastructure and disrupted operations for several weeks. This research aims to improve resilience to storm surges using hydrodynamic modelling coupled to an agent-based model of port operations. Using the December 2013 event to validate flood extent, depth and duration, we ran a high resolution hydrodynamic simulation using the open source Telemac 2D finite element code. The underlying Digital Elevation Model (DEM) was derived from Environment Agency LiDAR data, with ground truthing of the flood defences along the port frontage. Major infrastructure and buildings are explicitly resolved with varying degrees of permeability. Telemac2D simulations are run in parallel and take only minutes on a single 16 cpu compute node. Inundation characteristics predicted using Telemac 2D differ from a simple Geographical Information System 'bath-tub' analysis of the DEM based upon horizontal application of the maximum water level across the port topography. The hydrodynamic simulation predicts less extensive flooding and more closely matches observed flood extent. It also provides more precise depth and duration curves. Detailed spatial flood depth and duration maps were generated for a range of tide and surge scenarios coupled to mean sea-level rise projections. These inundation scenarios can then be integrated with critical asset databases and an agent-based model of port operation (MARS) that is capable of simulating storm surge disruption along wider supply chains. Port operators are able to act on information from a particular

Application of flexible micro temperature sensor in oxidative steam reforming by a methanol micro reformer.

Science.gov (United States)

Lee, Chi-Yuan; Lee, Shuo-Jen; Shen, Chia-Chieh; Yeh, Chuin-Tih; Chang, Chi-Chung; Lo, Yi-Man

2011-01-01

Advances in fuel cell applications reflect the ability of reformers to produce hydrogen. This work presents a flexible micro temperature sensor that is fabricated based on micro-electro-mechanical systems (MEMS) technology and integrated into a flat micro methanol reformer to observe the conditions inside that reformer. The micro temperature sensor has higher accuracy and sensitivity than a conventionally adopted thermocouple. Despite various micro temperature sensor applications, integrated micro reformers are still relatively new. This work proposes a novel method for integrating micro methanol reformers and micro temperature sensors, subsequently increasing the methanol conversion rate and the hydrogen production rate by varying the fuel supply rate and the water/methanol ratio. Importantly, the proposed micro temperature sensor adequately controls the interior temperature during oxidative steam reforming of methanol (OSRM), with the relevant parameters optimized as well.

Application of Flexible Micro Temperature Sensor in Oxidative Steam Reforming by a Methanol Micro Reformer

Directory of Open Access Journals (Sweden)

Yi-Man Lo

2011-02-01

Full Text Available Advances in fuel cell applications reflect the ability of reformers to produce hydrogen. This work presents a flexible micro temperature sensor that is fabricated based on micro-electro-mechanical systems (MEMS technology and integrated into a flat micro methanol reformer to observe the conditions inside that reformer. The micro temperature sensor has higher accuracy and sensitivity than a conventionally adopted thermocouple. Despite various micro temperature sensor applications, integrated micro reformers are still relatively new. This work proposes a novel method for integrating micro methanol reformers and micro temperature sensors, subsequently increasing the methanol conversion rate and the hydrogen production rate by varying the fuel supply rate and the water/methanol ratio. Importantly, the proposed micro temperature sensor adequately controls the interior temperature during oxidative steam reforming of methanol (OSRM, with the relevant parameters optimized as well.

Development Possibilities of the Port of Koper

Directory of Open Access Journals (Sweden)

Igor Trupac

2002-03-01

Full Text Available The extent to which Slovenia will exploit its good geographictransport position, whether it will be merely a transportcorridor or assume an additional quality (e.g. a distributioncentre or a logistic centre will depend on a cluster of circumstances.The importance will also be laid on how Slovenia willpresent itself and what it will offer to Europe and the rest of theworld. One of its best assets is the Port of Koper (favourable position,good condition, capacities in the frame of the whole logisticsystem.A larger volume of transport and consequently be/fer exploitationof the Port of Koper will in the future depend on increasedtransit. However, to acquire new cargo, the mere installationand modernisation of port infrastructure and rise in thequality of services may not be sufficient: it will also require goodconnections to the hinterland.

48 CFR 47.305-6 - Shipments to ports and air terminals.

Science.gov (United States)

2010-10-01

... transportation costs are concerned. (d) Unless logistics requirements limit the ports of loading to the ports...) When the delivery term is ex dock, pier, or warehouse, port of importation or c.& f. (cost & freight...) for the commodity. (4) When the delivery term is c.i.f. (cost, insurance, freight) destination, the...

Interior operators and topological connectedness | Castellini ...

African Journals Online (AJOL)

A categorical notion of interior operator is used in topology to define connectedness and disconnectedness with respect to an interior operator. A commutative diagram of Galois connections is used to show a relationship between these notions and Arhangelskii and Wiegandt's notions of connectedness and ...

Repair of traumatic tricuspid insufficiency via minimally invasive port access.

Science.gov (United States)

Kasahara, Hirofumi; Kudo, Mikihiko; Kawajiri, Hiroyuki; Yozu, Ryohei

2010-04-01

We report on a successful tricuspid valve plasty using port-access minimally invasive cardiac surgery (MICS) for severe traumatic tricuspid insufficiency caused by blunt chest trauma suffered 15 years previously. A combination repair procedure, consisting of cleft closures, plication of the anteroseptal commissure, and ring annuloplasty, was necessary to achieve valve competence and proved possible via port access without difficulty. Port-access MICS is an alternative approach for tricuspid valve surgery.

Design and integration of lower ports for ITER diagnostic systems

Energy Technology Data Exchange (ETDEWEB)

Casal, Natalia, E-mail: Natalia.casal@iter.org [ITER Organization, Route de Vinon-sur-Verdon – CS 90 046 – 13067 St Paul Lez Durance Cedex (France); Bertalot, Luciano; Cheng, Hao; Drevon, Jean Marc; Duckworth, Philip; Giacomin, Thibaud; Guirao, Julio; Iglesias, Silvia [ITER Organization, Route de Vinon-sur-Verdon – CS 90 046 – 13067 St Paul Lez Durance Cedex (France); Kochergin, Mikhail [IOFFE Institute, Saint Petersburg (Russian Federation); Martin, Alex [ITER Organization, Route de Vinon-sur-Verdon – CS 90 046 – 13067 St Paul Lez Durance Cedex (France); McCarron, Eddie [Oxford Technologies Ltd., Abingdon (United Kingdom); Mokeev, Alexander [Russian Federation Domestic Agency, Moscow (Russian Federation); Mota, Fernando [CIEMAT, Madrid (Spain); Penot, Christophe; Portales, Mickael [ITER Organization, Route de Vinon-sur-Verdon – CS 90 046 – 13067 St Paul Lez Durance Cedex (France); Kitazawa, Sin-iti [Japanese Domestic Agency, Naka (Japan); Sky, Jack [Oxford Technologies Ltd., Abingdon (United Kingdom); Suarez, Alejandro; Udintsev, Victor; Utin, Yuri [ITER Organization, Route de Vinon-sur-Verdon – CS 90 046 – 13067 St Paul Lez Durance Cedex (France); and others

2015-10-15

Highlights: • Lower port structures are in its conceptual design phase. • Electromagnetic and seismic loads, will dominate all other mechanical loads. • Design allows diagnostics support, neutron shielding while and signals transmission. • Installation and maintenance operations are fully remote handling compatible. - Abstract: All around the ITER vacuum vessel, forty-four ports will provide access to the vacuum vessel for remote handling operations, diagnostic systems, heating, and vacuum systems: 18 upper ports, 17 equatorial ports, and 9 lower ports. Among the lower ports, three of them will be used for the remote handling installation of the ITER divertor. Once the divertor is in place, these ports will host various diagnostic systems mounted in the so-called diagnostic racks. The diagnostic racks must allow the support and cooling of the diagnostics, extraction of the required diagnostic signals, and providing access and maintainability while minimizing the leakage of radiation toward the back of the port where the humans are allowed to enter. A fully integrated inner rack, carrying the near plasma diagnostic components, will be an stainless steel structure, 4.2 m long, with a maximum weight of 10 t. This structure brings water for cooling and baking at maximum temperature of 240 °C and provides connection with gas, vacuum and electric services. Additional racks (placed away from plasma and not requiring cooling) may be required for the support of some particular diagnostic components. The diagnostics racks and its associated ex vessel structures, which are in its conceptual design phase, are being designed to survive the lifetime of ITER of 20 years. This paper presents the current state of development including interfaces, diagnostic integration, operation and maintenance, shielding requirements, remote handling, loads cases and discussion of the main challenges coming from the severe environment and engineering requirements.

33 CFR 110.155 - Port of New York.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Port of New York. 110.155 Section... ANCHORAGE REGULATIONS Anchorage Grounds § 110.155 Port of New York. (a) Long Island Sound—(1) Anchorage No... northwest corner of the crib icebreaker north of the New York Central Railroad Company drawbridge across...

Goods Movement and Ports: Community Impacts and Collaborative Solutions (January 2014 Webinar)

Science.gov (United States)

To exchange views and develop a shared understanding of the challenges and opportunities of ports and port communities, EPA's Office of Transportation and Air Quality is hosting a series of webinars, bringing together port stakeholders.

Technical Efficiency and Port Competition: Revisiting the Bohai Economic Rim, China

Directory of Open Access Journals (Sweden)

Grace Wang

2012-12-01

Full Text Available The Bohai Economic Rim plays an important role in supporting China’s economic growth. For this research, we selected nine main ports in the region to study whether intra-port competition or corporatization would improve efficiency. Using a panel fixed effect model and stochastic frontier model, we found that the technical efficiency of selected ports is significantly influenced by the time of the initial public offering than by regional competition. The results are supportive and encouraging for policy makers to move toward the decentralized port governance in China.

A new system for port films.

Science.gov (United States)

Sephton, R; Green, M; Fitzpatrick, C

1989-01-01

A novel system for port films is described which incorporates a high-quality fluorescent screen lying behind a flat, heavy-metal screen or filter and the film pressed between them is not an X ray type but a single-emulsion, very high contrast graphics or line-type film. In experimental comparisons using 4 MV, 6 MV, and 25 MV photon beams, the new Peter MacCallum Cancer Institute (PMCI) system produced clearer images, about X2 higher in contrast yet lower in relative noise levels, than did the conventional commercially-available systems which use x-ray film between heavy-metal screens. Direct clinical comparisons, chiefly using 6 MV accelerators, confirmed that anatomical details were correspondingly better visualized and in general, the PMCI port film could be matched against the simulator radiograph with greater confidence. Routine use for greater than 2 yr in this Institute (4000 new patients per yr, 20 cassettes made for use with four 6 MV accelerators) has shown the PMCI system to be an economical and practical device, giving reproducibly high quality images in all the common port film applications.

Characteristics of drayage operations at the Port of Houston.

Science.gov (United States)

2008-09-01

Port drayage, defined as a container truck pickup to or from a seaport terminal with both the trip : origin and destination in the same urban area, is a critical yet comparatively understudied link in the : intermodal supply chain. Because port dray ...

Perception of Rape Amongst Secondary School Students In Port ...

African Journals Online (AJOL)

Alasia Datonye

Department of Paediatrics and Child health, University of Port Harcourt, Teaching Hospital,. Port Harcourt, Nigeria. ABSTRACT ... questionnaire, data collected included bio data, awareness information, response and practices. ..... behaviour and experience of sexual coercion among secondary school studenta in three ...

An Analysis of Port-Visit Costs of U.S. Navy Aircraft Carriers

Science.gov (United States)

2008-06-01

Hong Kong are less expensive than visits to Port Klang, Malaysia or Laem Chabang, Thailand. The cost difference between conducting a port visit in...less than a comparable visit to nearby Port Klang, Malaysia . It is understandable that decisions on which ports to visit are governed by more than...to support manpower/efficiency initiatives. • Galley and Food Service equipment modifications to support Large Afloat Franchise Menu will be

Interior Design Students Perceptions of Sustainability

Science.gov (United States)

Stark, Johnnie; Park, Jin Gyu

2016-01-01

Purpose: This longitudinal study assessed student perceptions of sustainable design issues in the context of an accredited interior design program. Although literature exists documenting the integration of sustainable strategies into interior design curriculum, more analysis is needed to determine the impact of program experiences on students'…

Thermo-hydraulic analysis of the generic equatorial port plug design

International Nuclear Information System (INIS)

Rodríguez, E.; Guirao, J.; Ordieres, J.; Cortizo, J.L.; Iglesias, S.

2012-01-01

Highlights: ► Thermo-hydraulic transient performance evaluation and optimization of the GEPP structure cooling/heating system under neutronic heating and baking conditions. ► The optimization of the GEPP box structure's cooling system includes positioning and minimization of number and size of gun drilled channels, complying with the flow and functional requirements during operating and baking conditions. - Abstract: The port-based ITER diagnostic systems are housed primarily in two locations, the equatorial and upper port plugs. The port plug structure provides confinement function, maintains ultra-high vacuum quality and the first confinement barrier for radioactive materials at the ports. The port plug structure design, from the ITER International Organisation (IO), is cooled and heated by pressurized water which flows through a series of gun-drilled water channels and water pipes. The cooling function is required to remove nuclear heating due to radiation during operation of ITER, while the heating function is intended to heat up uniformly the machine during baking condition. The work presented provides coupled thermo-hydraulic analysis and optimization of a Generic Equatorial Port Plug (GEPP) structure cooling and heating system. The optimization performed includes positioning, minimization of number and size of gun drilled channels, complying with the flow and functional requirements during operating and baking conditions.

Natural thorium isotopes in marine sediment core off Labuan port

Energy Technology Data Exchange (ETDEWEB)

Hafidz, B. Y.; Asnor, A. S.; Terence, R. C.; Mohamed, C. A. R. [School of Environmental and Natural Resource Sciences, Faculty of Science and Technology, Universiti Kebangsaan Malaysia 43600, Bangi, Selangor (Malaysia)

2014-02-12

Sediment core was collected from Labuan port and analyzed to determine the radioactivity of thorium (Th) isotopes. The objectives of this study are to determine the possible sources of Th isotopes at Labuan port and estimates the sedimentation rate based on {sup 228}Th/{sup 232}Th model. The results suggest the {sup 230}Th and {sup 232}Th might be originated from terrestrial sedimentary rock while {sup 228}Th originated by authigenic origin. High ratio value of {sup 230}Th/{sup 232}Th detected at the top surface sediment indicates the increasing of {sup 230}Th at the recent years which might be contributed from the anthropogenic sources. The sedimentation rate of core sediment from Labuan Port was successfully estimated by using {sup 228}Th/{sup 232}Th model. The result show high sedimentation rate with 4.67 cm/year indicates rapid deposition occurred at this study area due to the high physical activity at the Labuan port. By assume the constant sedimentation rate at this area; we estimated the age of 142 cm core sediment obtained from Labuan port is 32 years started from 1981 to 2012. This chronology will be used in forthcoming research to investigate the historical profile of anthropogenic activities affecting the Labuan port.